WorldWideScience

Sample records for system devices panel

  1. 78 FR 49272 - Circulatory System Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting

    Science.gov (United States)

    2013-08-13

    .... The hotel telephone number is 301-977-8900. Contact Person: Jamie Waterhouse, Center for Devices and..., pneumatically, or electrically and (2) devices that aid the emergency medical professional in delivering manual...

  2. Overview of the 2016 U.S. Food and Drug Administration Circulatory System Devices Advisory Panel Meeting on the Absorb Bioresorbable Vascular Scaffold System.

    Science.gov (United States)

    Steinvil, Arie; Rogers, Toby; Torguson, Rebecca; Waksman, Ron

    2016-09-12

    This study aims to describe the discussions and recommendations made during the U.S. Food and Drug Administration (FDA) Circulatory System Device Panel pre-market approval application for the Absorb Bioresorbable Vascular Scaffold (BVS) System. The Absorb BVS System is a first-of-its-kind fully bioresorbable percutaneous coronary intervention technology. The absorb BVS was studied in the ABSORB III (A Clinical Evaluation of Absorb BVS, the Everolimus Eluting Bioresorbable Vascular Scaffold in the Treatment of Subjects with de Novo Native Coronary Artery Lesions) trial, the pivotal U.S. investigational device exemption trial. Observational report of the FDA Circulatory System Device Panel pre-market approval application meeting held on March 15, 2016. The U.S. FDA Circulatory System Device Panel members reviewed the ABSROB III trial outcomes and additional post hoc analyses presented by the sponsor and the FDA. The ABSORB III trial met the primary endpoint of noninferiority of Absorb BVS compared with the control, XIENCE drug-eluting stent, for target lesion failure at 1 year. Although a higher numerical trend for adverse outcomes was reported for the Absorb BVS, there were no statistical differences between Absorb BVS and XIENCE for any safety or effectiveness components for target lesion failure or for the secondary pre-specified outcomes. Panel members raised concerns with regard to the ABSORB III results and post hoc analyses focusing mainly on the noninferiority design of the trial, the apparent safety issues of the Absorb BVS in small vessels, the mismatch of visually versus intravascular imaging assessed vessel size found in ABSORB III and its implications on the adequate device labeling, the safety of Absorb BVS in specific patient and lesion subsets, and the post-approval commitments of the sponsor. Following panel discussions and the evidence presented, the panel voted for approval of the device. Copyright © 2016 American College of Cardiology Foundation

  3. 76 FR 50485 - Obstetrics and Gynecology Devices Panel of the Medical Devices Advisory Committee; Amendment of...

    Science.gov (United States)

    2011-08-15

    ...] Obstetrics and Gynecology Devices Panel of the Medical Devices Advisory Committee; Amendment of Notice AGENCY... an amendment to the notice of meeting of the Obstetrics and Gynecology Devices Panel of the Medical... Obstetrics and Gynecology Devices Panel of the Medical Devices Advisory Committee would be held on September...

  4. 78 FR 26786 - Microbiology Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting

    Science.gov (United States)

    2013-05-08

    ... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2013-N-0001] Microbiology Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting AGENCY: Food and Drug...: Microbiology Devices Panel of the Medical Devices Advisory Committee. General Function of the Committee: To...

  5. 76 FR 55398 - Immunology Devices Panel of the Medical Devices Advisory Committee: Notice of Postponement of...

    Science.gov (United States)

    2011-09-07

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration Immunology Devices Panel of the Medical Devices Advisory.... SUMMARY: The Food and Drug Administration (FDA) is postponing the meeting of the Immunology Devices Panel...

  6. 76 FR 48871 - Immunology Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting

    Science.gov (United States)

    2011-08-09

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration Immunology Devices Panel of the Medical Devices Advisory...). The meeting will be open to the public. Name of Committee: Immunology Devices Panel of the Medical...

  7. 78 FR 13347 - Clinical Chemistry and Clinical Toxicology Devices Panel of the Medical Devices Advisory...

    Science.gov (United States)

    2013-02-27

    ... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2013-N-0001] Clinical Chemistry and Clinical Toxicology Devices Panel of the Medical Devices Advisory Committee; Notice... be open to the public. Name of Committee: Clinical Chemistry and Clinical Toxicology Devices Panel of...

  8. 78 FR 63225 - Ear, Nose and Throat Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting

    Science.gov (United States)

    2013-10-23

    ... HUMAN SERVICES Food and Drug Administration Ear, Nose and Throat Devices Panel of the Medical Devices... Federal Register about last minute modifications that impact a previously announced advisory committee... for the Nucleus Hybrid TM L24 Implant System sponsored by Cochlear Americas. The proposed Indications...

  9. Solar panel truss mounting systems and methods

    Energy Technology Data Exchange (ETDEWEB)

    Al-Haddad, Tristan Farris; Cavieres, Andres; Gentry, Russell; Goodman, Joseph; Nolan, Wade; Pitelka, Taylor; Rahimzadeh, Keyan; Brooks, Bradley; Lohr, Joshua; Crooks, Ryan; Porges, Jamie; Rubin, Daniel

    2018-01-30

    An exemplary embodiment of the present invention provides a solar panel truss mounting system comprising a base and a truss assembly coupled to the base. The truss assembly comprises a first panel rail mount, second panel rail mount parallel to the first panel rail mount, base rail mount parallel to the first and second panel rail mounts, and a plurality of support members. A first portion of the plurality of support members extends between the first and second panel rail mounts. A second portion of the plurality of support members extends between the first panel rail mount and the base rail mount. A third portion of the plurality of support members extends between the second panel rail mount and the base rail mount. The system can further comprise a plurality of connectors for coupling a plurality of photovoltaic solar panels to the truss assembly.

  10. Solar panel truss mounting systems and methods

    Science.gov (United States)

    Al-Haddad, Tristan Farris; Cavieres, Andres; Gentry, Russell; Goodman, Joseph; Nolan, Wade; Pitelka, Taylor; Rahimzadeh, Keyan; Brooks, Bradley; Lohr, Joshua; Crooks, Ryan; Porges, Jamie; Rubin, Daniel

    2015-10-20

    An exemplary embodiment of the present invention provides a solar panel truss mounting system comprising a base and a truss assembly coupled to the base. The truss assembly comprises a first panel rail mount, second panel rail mount parallel to the first panel rail mount, base rail mount parallel to the first and second panel rail mounts, and a plurality of support members. A first portion of the plurality of support members extends between the first and second panel rail mounts. A second portion of the plurality of support members extends between the first panel rail mount and the base rail mount. A third portion of the plurality of support members extends between the second panel rail mount and the base rail mount. The system can further comprise a plurality of connectors for coupling a plurality of photovoltaic solar panels to the truss assembly.

  11. Guns and High Gas Output Devices Panel: Introduction

    Science.gov (United States)

    Simmons, Ronald L.; Kaste, Pamela J.

    2000-01-01

    A new panel known as the Guns and High Gas Output Panel was organized in 1999 under the auspices of the JANNAF Propellant and Characterization SubCommittee (PDCS). This is an introduction to our first meeting, purpose of the panel, and the scope of activities to be covered. The primary purpose of the panel is very simple: to provide a single focal point for interfacing Government Laboratories (Department of Defense and Department of Energy) and commercial industry researchers to share R&D activities and findings (i.e. facilitate the exchange of information) specifically aimed at gun-launched propulsion and high-gas output devices (gas generators and air bag inflators). Specific areas of interest included in the Panel's scope (and the Technical Data Base) are the following: (1) new propellant formulations and chemistry, (2) new ingredients, (3) ballistic effects of the new formulations and ingredients, (4) new processing methods unique to gun propellants, (5) thermochemistry of new ingredients, (6) unique physical and mechanical properties, (7) burning rates of new propellants and small scale closed bomb testing, (8) plasma effects on the propellant, and (9) unique safety and insensitive munitions properties.

  12. 76 FR 18227 - Molecular and Clinical Genetics Panel of the Medical Devices Advisory Committee; Notice of...

    Science.gov (United States)

    2011-04-01

    ...] Molecular and Clinical Genetics Panel of the Medical Devices Advisory Committee; Notice of Meeting... comment period for the notice announcing a meeting of the Molecular and Clinical Genetics Panel (the panel... Clinical Genetics Panel of the Medical Devices Advisory Committee, and the opening of a public docket to...

  13. 76 FR 14414 - Microbiology Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting

    Science.gov (United States)

    2011-03-16

    ... DEPARTMENT OF HEALTH AND HUMAN SERVICES [Docket No. FDA-2011-N-0002] Microbiology Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting AGENCY: Food and Drug Administration, HHS... and Drug Administration (FDA). The meeting will be open to the public. Name of Committee: Microbiology...

  14. 78 FR 19717 - Clinical Chemistry and Clinical Toxicology Devices Panel of the Medical Devices Advisory...

    Science.gov (United States)

    2013-04-02

    ... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2013-N-0001] Clinical Chemistry and Clinical Toxicology Devices Panel of the Medical Devices Advisory Committee: Notice of Change of Meeting Schedule AGENCY: Food and Drug Administration, HHS. ACTION: Notice; correction...

  15. 76 FR 41507 - Obstetrics and Gynecology Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting

    Science.gov (United States)

    2011-07-14

    ... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2011-N-0002] Obstetrics and Gynecology Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting AGENCY... public. Name of Committee: Obstetrics and Gynecology Devices Panel of the Medical Devices Advisory...

  16. Structural noise from automatic exposure control device and its relationship to X-ray tube voltage used for calibration of a flat-panel detector system.

    Science.gov (United States)

    Mizuta, Masayoshi; Akazawa, Hiroyuki; Kasai, Toshifumi; Sanada, Shigeru; Abe, Shuji; Mitou, Shigeki

    2012-01-01

    In flat-panel detector (FPD) systems, the ion-chamber dosimeters used for automatic exposure control (AEC), which are placed between the detector and the source, should not affect clinical images because of FPD gain correction, but can sometimes still introduce fixed-pattern noise. In this study, we investigated whether such artifacts were caused by structural noise from the AEC detector on the basis of the noise power spectrum (NPS) and the mean square error (MSE) of FPD images taken at various tube voltages either with or without the AEC detector. When the NPS was measured without the AEC detector, the NPS did not increase in the low special-frequency band at all radiation qualities tested, irrespective of X-ray calibration tube voltages. However, when the NPS was measured while the AEC detector was used, the NPS increased in the low special-frequency band at all radiation qualities when the X-ray calibration tube voltages were at low levels. Similarly, the MSE increased when the X-ray calibration tube voltages were at low levels. From these results, artifacts in the AEC detector appear to be suppressed when a radiation quality of approximately 90 kV is used at four different standardized radiations quality (RQA3, RQA5, RQA7, and RQA9).

  17. Touch panel system for control applications

    International Nuclear Information System (INIS)

    Crook, K.; Johnson, R.

    1976-12-01

    The use of finger-sensitive touch panels in association with computer-generated displays for control and monitoring of the Stanford linear accelerator is discussed. This control concept has proven to be very effective. The hardware and software aspects of the Touch Panel portion of the control system are described

  18. Palletizing and depalletizing systems of soundproof panel; Boon panel depare/paredizu system

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-02-29

    The palletizing and depalletizing systems in the washing process of a soundproof panel were manufactured and delivered (Figure 12). The soundproof panels used in the construction field are supplied to this system using a forklift in the state where they were loaded on a pallet. A palletizer takes out the supplied soundproof panels one at a time and transfers them to the conveyor of a washing line. The palletizer also takes out the soundproof panels washed using a washer from the conveyor of a washing line and loads them on an empty pallet. Various effects (for example, liberation from simple and hard works and solution of insufficient man power) were obtained by introduction of this system. The main configuration of this system is as follows: (1) Palletizer (VPR-800) x 2. (2) Controller (meirocs-G) x 2. (3) Panel catch-only hand x 2. (4) Pallet carrier unit x 1. (5) Panel carrier unit x 1. (translated by NEDO)

  19. Automatic outdoor monitoring system for photovoltaic panels.

    Science.gov (United States)

    Stefancich, Marco; Simpson, Lin; Chiesa, Matteo

    2016-05-01

    Long-term acquisition of solar panel performance parameters, for panels operated at maximum power point in their real environment, is of critical importance in the photovoltaic research sector. However, few options exist for the characterization of non-standard panels such as concentrated photovoltaic systems, heavily soiled or shaded panels or those operating under non-standard spectral illumination; certainly, it is difficult to find such a measurement system that is flexible and affordable enough to be adopted by the smaller research institutes or universities. We present here an instrument aiming to fill this gap, autonomously tracking and maintaining any solar panel at maximum power point while continuously monitoring its operational parameters and dissipating the produced energy without connection to the power grid. The instrument allows periodic acquisition of current-voltage curves to verify the employed maximum power point tracking approach. At the same time, with hardware schematics and software code being provided, it provides a flexible open development environment for the monitoring of non-standard generators like concentrator photovoltaic systems and to test novel power tracking approaches. The key issues, and the corresponding solutions, encountered in the design are analyzed in detail and the relevant schematics presented.

  20. Automatic outdoor monitoring system for photovoltaic panels

    Energy Technology Data Exchange (ETDEWEB)

    Stefancich, Marco [Consiglio Nazionale delle Ricerce, Istituto dei Materiali per l’Elettronica ed il Magnetismo (CNR-IMEM), Parco Area delle Scienze 37/A, 43124 Parma, Italy; Simpson, Lin [National Renewable Energy Laboratory, 15013 Denver West Parkway, Golden, Colorado 80401, USA; Chiesa, Matteo [Masdar Institute of Science and Technology, P.O. Box 54224, Masdar City, Abu Dhabi, United Arab Emirates

    2016-05-01

    Long-term acquisition of solar panel performance parameters, for panels operated at maximum power point in their real environment, is of critical importance in the photovoltaic research sector. However, few options exist for the characterization of non-standard panels such as concentrated photovoltaic systems, heavily soiled or shaded panels or those operating under non-standard spectral illumination; certainly, it is difficult to find such a measurement system that is flexible and affordable enough to be adopted by the smaller research institutes or universities. We present here an instrument aiming to fill this gap, autonomously tracking and maintaining any solar panel at maximum power point while continuously monitoring its operational parameters and dissipating the produced energy without connection to the power grid. The instrument allows periodic acquisition of current-voltage curves to verify the employed maximum power point tracking approach. At the same time, with hardware schematics and software code being provided, it provides a flexible open development environment for the monitoring of non-standard generators like concentrator photovoltaic systems and to test novel power tracking approaches. The key issues, and the corresponding solutions, encountered in the design are analyzed in detail and the relevant schematics presented.

  1. Developing a solar panel testing system

    Directory of Open Access Journals (Sweden)

    Árpád Rácz

    2009-10-01

    Full Text Available Solar energy is increasingly used togenerate electricity for individual households. There isa wide variety of solar panel technologies, whichshould be tested at an individual level during theirlifetime. In this paper, the development of a testingstation at the University of Debrecen is presented. Thetesting system can be used for research andeducational purposes and for in field applicationsequally well.

  2. 78 FR 16684 - General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee; Notice of...

    Science.gov (United States)

    2013-03-18

    ... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2013-N-0001] General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting AGENCY: Food and Drug Administration, HHS. ACTION: Notice. This notice announces a forthcoming meeting of a public advisory committee of the Food...

  3. 75 FR 49940 - General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee; Notice of...

    Science.gov (United States)

    2010-08-16

    ... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2010-N-0001] General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting AGENCY: Food and Drug Administration, HHS. ACTION: Notice. This notice announces a forthcoming meeting of a public advisory committee of the Food...

  4. 75 FR 36102 - General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee; Notice of...

    Science.gov (United States)

    2010-06-24

    ... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2010-N-0001] General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting AGENCY: Food and Drug Administration, HHS. ACTION: Notice. This notice announces a forthcoming meeting of a public advisory committee of the Food...

  5. 75 FR 61507 - General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee; Amendment of...

    Science.gov (United States)

    2010-10-05

    ... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2010-N-0001] General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee; Amendment of Notice AGENCY: Food and Drug Administration, HHS. ACTION: Notice. The Food and Drug Administration (FDA) is announcing an amendment to the notice of...

  6. 76 FR 62419 - General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee; Notice of...

    Science.gov (United States)

    2011-10-07

    ... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2011-N-0002] General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting AGENCY: Food and Drug Administration, HHS. ACTION: Notice. This notice announces a forthcoming meeting of a public advisory committee of the Food...

  7. 76 FR 14415 - General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee; Notice of...

    Science.gov (United States)

    2011-03-16

    ... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2011-N-0002] General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting AGENCY: Food and Drug Administration, HHS. ACTION: Notice. This notice announces a forthcoming meeting of a public advisory committee of the Food...

  8. 77 FR 20642 - General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee; Notice of...

    Science.gov (United States)

    2012-04-05

    ... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2012-N-0001] General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting AGENCY: Food and Drug Administration, HHS. ACTION: Notice. This notice announces a forthcoming meeting of a public advisory committee of the Food...

  9. 76 FR 39882 - General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee; Notice of...

    Science.gov (United States)

    2011-07-07

    ... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2011-N-0478] General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting AGENCY: Food and Drug Administration, HHS. ACTION: Notice. This notice announces a forthcoming meeting of a public advisory committee of the Food...

  10. 76 FR 42713 - General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee; Amendment of...

    Science.gov (United States)

    2011-07-19

    ... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2011-N-0478] General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee; Amendment of Notice AGENCY: Food and Drug Administration, HHS. ACTION: Notice. The Food and Drug Administration (FDA) is announcing an amendment to the notice of...

  11. Sound transmission reduction with intelligent panel systems

    Science.gov (United States)

    Fuller, Chris R.; Clark, Robert L.

    1992-01-01

    Experimental and theoretical investigations are performed of the use of intelligent panel systems to control the sound transmission and radiation. An intelligent structure is defined as a structural system with integrated actuators and sensors under the guidance of an adaptive, learning type controller. The system configuration is based on the Active Structural Acoustic Control (ASAC) concept where control inputs are applied directly to the structure to minimize an error quantity related to the radiated sound field. In this case multiple piezoelectric elements are employed as sensors. The importance of optimal shape and location is demonstrated to be of the same order of influence as increasing the number of channels of control.

  12. 75 FR 76757 - Licensing Support System Advisory Review Panel

    Science.gov (United States)

    2010-12-09

    ... NUCLEAR REGULATORY COMMISSION Licensing Support System Advisory Review Panel AGENCY: U.S. Nuclear... Review Panel (LSNARP). SUMMARY: The Licensing Support System Advisory Review Panel was established by the... system to be used to store and retrieve documents relating to the licensing of a geologic repository for...

  13. An orientable solar panel system for nanospacecraft

    Science.gov (United States)

    Santoni, Fabio; Piergentili, Fabrizio; Candini, Gian Paolo; Perelli, Massimo; Negri, Andrea; Marino, Michele

    2014-08-01

    An orientable deployed solar array system for 1-5 kg weight nanospacecraft is described, enhancing the achievable performance of these typically power-limited systems. The system is based on a deployable solar panel system, previously developed with cooperation between Laboratorio di Sistemi Aerospaziali of University of Roma “la Sapienza” and the company IMT (Ingegneria Marketing Tecnologia). The system proposed is a modular one, and suitable in principle for the 1U, 2U and 3U standard Cubesat bus, even if the need for three axis attitude stabilization makes it typically preferred for 3U Cubesats. The size of each solar panel is the size of a lateral Cubesat surface. A single degree of freedom maneuvering capability is given to the deployed solar array, in order to follow the apparent motion of the sun as close as possible, given the mission requirements on the spacecraft attitude. Considerable effort has been devoted to design the system compatible with the Cubesat standard, being mounted outside on the external spacecraft structure, without requiring modifications on the standard prescriptions. The small available volume is the major constraint, which forces to use miniaturized electric motor technology. The system design trade-off is discussed, leading to the selection of an architecture based on two independently steerable solar array wings.

  14. 75 FR 4407 - The Neurological Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting

    Science.gov (United States)

    2010-01-27

    .... Contact Person: Deborah Falls, Center for Devices and Radiological Health, Food and Drug Administration... premarket approval application for the Deep Brain Stimulation System for Epilepsy sponsored by Medtronic...-onset seizures (affecting only a part of the brain when they begin), with or without secondary...

  15. DC current distribution mapping system of the solar panels using a HTS-SQUID gradiometer

    International Nuclear Information System (INIS)

    Miyazaki, Shingo; Kasuya, Syohei; Saari, Mohd Mawardi; Sakai, Kenji; Kiwa, Toshihiko; Tsukada, Keiji; Tsukamoto, Akira; Adachi, Seiji; Tanabe, Keiichi

    2014-01-01

    Solar panels are expected to play a major role as a source of sustainable energy. In order to evaluate solar panels, non-destructive tests, such as defect inspections and response property evaluations, are necessary. We developed a DC current distribution mapping system of the solar panels using a High Critical Temperature Superconductor Superconducting Quantum Interference Device (HTS-SQUID) gradiometer with ramp edge type Josephson junctions. Two independent components of the magnetic fields perpendicular to the panel surface (∂Bz/∂x, ∂Bz/∂y) were detected. The direct current of the solar panel is visualized by calculating the composition of the two signal components, the phase angle, and mapping the DC current vector. The developed system can evaluate the uniformity of DC current distributions precisely and may be applicable for defect detection of solar panels.

  16. Medical devices; immunology and microbiology devices; classification of respiratory viral panel multiplex nucleic acid assay. Final rule.

    Science.gov (United States)

    2009-10-09

    The Food and Drug Administration (FDA) is announcing the classification of the respiratory viral panel multiplex nucleic acid assay into class II (special controls). The special controls that will apply to the device are three guidance documents entitled: "Class II Special Controls Guidance Document: Respiratory Viral Panel Multiplex Nucleic Acid Assay," as applicable, "Class II Special Controls Guidance Document: Testing for Human Metapneumovirus (hMPV) Using Nucleic Acid Assays," and as applicable,"Class II Special Controls Guidance Document: Testing for Detection and Differentiation of Influenza A Virus Subtypes Using Multiplex Nucleic Acid Assays.'' The agency classified the device into class II (special controls) in order to provide a reasonable assurance of safety and effectiveness of the device. Elsewhere in this issue of the Federal Register, FDA is announcing the availability of the guidance documents that will serve as the special controls for this device.

  17. 75 FR 47606 - General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee; Notice of...

    Science.gov (United States)

    2010-08-06

    ...The meeting of the General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee scheduled for August 26, 2010, is postponed. The meeting was announced in the Federal Register of June 24, 2010 (75 FR 36102). The meeting is postponed so that FDA can review and consider additional information that was submitted. A future meeting date will be announced in the Federal Register at a later date.

  18. 76 FR 65200 - General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee: Notice of...

    Science.gov (United States)

    2011-10-20

    ...The Food and Drug Administration (FDA) is postponing the meeting of the General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee scheduled for December 1, 2011. The meeting was announced in the Federal Register of Friday, October 7, 2011 (76 FR 62419). The meeting is postponed so that FDA can review and consider additional information that was submitted. A future meeting date will be announced in the Federal Register.

  19. 75 FR 33315 - Dental Products Panel of the Medical Devices Advisory Committee; Notice of Meeting

    Science.gov (United States)

    2010-06-11

    ... received by FDA concerning the final rule on the classification of dental amalgam, which published in the... adequacy of the risk assessment performed by FDA in classifying dental amalgam in light of a new report on... HUMAN SERVICES Food and Drug Administration Dental Products Panel of the Medical Devices Advisory...

  20. 76 FR 6623 - Molecular and Clinical Genetics Panel of the Medical Devices Advisory Committee; Notice of Meeting

    Science.gov (United States)

    2011-02-07

    ... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2011-N-0066] Molecular and Clinical Genetics Panel of the Medical Devices Advisory Committee; Notice of Meeting AGENCY... public. Name of Committee: Molecular and Clinical Genetics Panel of the Medical Devices Advisory...

  1. 78 FR 77689 - Orthopaedic and Rehabilitation Devices Panel of the Medical Devices Advisory Committee; Notice of...

    Science.gov (United States)

    2013-12-24

    ... diagnosis of cystic fibrosis or for other uses if the drug intended for use with the device bears adequate... 50520) for classification of iontophoresis devices for specialized uses (for the diagnosis of cystic... cystic fibrosis or other uses if the labeling of the drug intended for use with the device bears adequate...

  2. Photovoltaic Thermal panels in collective thermal solar systems

    International Nuclear Information System (INIS)

    Elswijk, M.J.; Strootman, K.J.; Jong, M.J.M.; De Lange, E.T.N.; Smit, W.F.

    2003-12-01

    A feasibility study has been carried out to assess the options to apply photovoltaic/thermal panels (PVT-panels) in collective solar thermal systems in urban areas in the Netherlands. The study was focused on the technical (architecture and installations) and the economical feasibility of collective PVT-systems in comparison with conventional solar thermal systems and combinations of photovoltaic (PV) panels and solar collectors. The results of the study also give insight into cost and the market for PVT-panels. Three case studies in which collective solar collector systems were applied are analyzed again by simulating the installation of a PVT-panels system and a separate solar thermal PV system [nl

  3. 75 FR 1446 - Future Systems Technology Advisory Panel Meeting

    Science.gov (United States)

    2010-01-11

    ... SOCIAL SECURITY ADMINISTRATION [Docket No. SSA-2010-0001] Future Systems Technology Advisory Panel...: February 3, 2010, 10:30 a.m.-5 p.m. and February 4, 2010, 8:30 a.m.-12 p.m. Location: The Latham Hotel... systems technology and electronic services at the agency five to ten years into the future. The Panel will...

  4. Introduction of an Innovative Cladding Panel System for Multi-Story Buildings

    Directory of Open Access Journals (Sweden)

    Hathairat Maneetes

    2014-08-01

    Full Text Available An Energy Dissipating Cladding System has been developed for use in buildings designed based on the concept of damage-controlled structure in seismic design. This innovative cladding panel system is capable of functioning both as a structural brace, as well as a source of energy dissipation, without demanding inelastic action and ductility from the basic lateral force resisting system. The structural systems of many modern buildings typically have large openings to accommodate glazing systems, and a popular type of construction uses spandrel precast cladding panels at each floor level that supports strip window systems. The present study focuses on developing spandrel type precast concrete cladding panels as supplementary energy dissipating devices that are added to the basic structural system. Through a series of analytical studies, the result of evaluating the ability of the proposed Energy Dissipating Cladding system to improve the earthquake resistance of the buildings is presented here.

  5. 78 FR 25747 - Gastroenterology and Urology Devices Panel of the Medical Devices Advisory Committee; Notice of...

    Science.gov (United States)

    2013-05-02

    ... make recommendations regarding the proposed classification of implanted blood access devices for hemodialysis from class III to class II. The class III implanted blood access devices for hemodialysis include... tubing terminating in rigid Luer lock connectors for attachment to a dialysis machine. Subcutaneous...

  6. 75 FR 18566 - Future Systems Technology Advisory Panel Meeting

    Science.gov (United States)

    2010-04-12

    ... SOCIAL SECURITY ADMINISTRATION [Docket No. SSA-2010-0014] Future Systems Technology Advisory Panel Meeting AGENCY: Social Security Administration (SSA). ACTION: Notice of Seventh Panel Meeting. DATES: May 4, 2010, 9 a.m.-5 p.m. Location: Hotel Palomar, Bumham Ballroom. ADDRESSES: 117 South 17th Street...

  7. Photovoltaic solar panel for a hybrid PV/thermal system

    Energy Technology Data Exchange (ETDEWEB)

    Zakharchenko, R.; Licea-Jimenez, L.; Perez-Garcia, S.A.; Perez-Robles, J.F.; Gonzalez-Hernandez, J.; Vorobiev, Y. [CINVESTAV-Queretaro, (Mexico); Vorobiev, P. [Universidad Autonoma de Queretaro, (Mexico). Facultad de Ingenieria; Dehesa-Carrasco, U. [Instituto Tec. Del Istmo, Oaxaco (Mexico). Dep. de Ingenieria Electromecanica

    2004-05-01

    The hybrid PV-thermal system was studied, with the photovoltaic panel (PVP) area much smaller than that of the solar collector. Performance of the different panels in the system was investigated, in particular, those made of crystalline (c-) Si, {alpha}-Si and CuInSe{sub 2} as well as different materials and constructions for the thermal contact between the panel and the collector. Our conclusion is that the PVP for application in a hybrid system needs a special design providing efficient heat extraction from it. PVP was designed and made. Its study has shown that this design provides the high electrical and thermal efficiency of the hybrid system. (author)

  8. Monitoring and control system of charging batteries connected to a photovoltaic panel

    Science.gov (United States)

    Idzkowski, Adam; Leoniuk, Katarzyna; Walendziuk, Wojciech; Budzynski, Lukasz

    2015-09-01

    In this paper the off-grid photovoltaic system consisting of a PV panel, MMPT charge controller and battery is described. The realization of a laboratory stand for charging or discharging batteries is presented. Original monitoring and control system, which is based on LabVIEW software and LabJack DAQ device, has been built. Data acquisition part, arithmetic part and front panel of program created in LabVIEW are described. Some problems with implementation of this system, providing the monitoring of electrical parameters, are mentioned.

  9. 75 FR 36660 - Orthopaedic and Rehabilitation Devices Panel of the Medical Devices Advisory Committee; Notice of...

    Science.gov (United States)

    2010-06-28

    ...., Gaithersburg, MD. Contact Person: Tracy Phillips, Food and Drug Administration, Center for Devices and... special needs. If you require special accommodations due to a disability, please contact AnnMarie Williams...

  10. 77 FR 32125 - Orthopaedic and Rehabilitation Devices Panel of the Medical Devices Advisory Committee; Amendment...

    Science.gov (United States)

    2012-05-31

    .... There are no other changes. FOR FURTHER INFORMATION CONTACT: Avena Russell, Center for Devices and..., MD 20993-0002, 301-796-3805, Avena[email protected] , or please use the FDA Advisory Committee...

  11. 76 FR 71045 - Neurological Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting

    Science.gov (United States)

    2011-11-16

    ... (301) 977-8900. Contact Person: Avena Russell, Center for Devices and Radiological Health, Food and Drug Administration, 10903 New Hampshire Ave., Bldg. 66, Rm. 1535, Silver Spring, MD 20993-0002, Avena...

  12. 76 FR 71983 - Gastroenterology and Urology Devices Panel of the Medical Devices Advisory Committee; Notice of...

    Science.gov (United States)

    2011-11-21

    ... 20877. The hotel's telephone number is (301) 977-8900. Contact Person: Avena Russell, Center for Devices..., Silver Spring, MD 20993-0002, Avena[email protected] , (301) 796-3805, or FDA Advisory Committee...

  13. A simple tracking system to monitor solar PV panels

    International Nuclear Information System (INIS)

    Bentaher, H.; Kaich, H.; Ayadi, N.; Ben Hmouda, M.; Maalej, A.; Lemmer, U.

    2014-01-01

    Highlights: • We designed and constructed a solar tracking system based on light-dependent resistors (LDRs). • A study was made to determine the optimal angle of LDRs inducing the best precision of the device. • An experimental system was built to test different values of the angle between LDRs. • Results showed a good agreement between the experience and the predicted values. • The obtained results are useful for the design of new trackers based on the use of LDRs. - Abstract: The solar tracking systems are a center of interest of a big number of researchers from the fifties. The deflection of sun rays on a solar photovoltaic panel can reduce its power output until 50%. For concentrators solar trackers are master parts of the systems. A simple tracking system based on light dependent resistors was locally constructed, tested and optimized. Good agreement was recorded between numerical optimization results and experimental ones. These results are useful for the design and construction of new sun trackers

  14. 75 FR 9422 - Orthopaedic and Rehabilitation Devices Panel of the Medical Devices Advisory Committee; Notice of...

    Science.gov (United States)

    2010-03-02

    ... A, B, C and D, 620 Perry Pkwy., Gaithersburg, MD. Contact Person: Tracy Phillips, Center for Devices... 20993, 301-796-6150, Tracy[email protected] , or FDA Advisory Committee Information Line, 1-800-741... special needs. If you require special accommodations due to a disability, please contact AnnMarie Williams...

  15. 78 FR 24426 - Orthopaedic and Rehabilitation Devices Panel of the Medical Devices Advisory Committee; Notice of...

    Science.gov (United States)

    2013-04-25

    ... application for the Kineflex/C Cervical Artificial Disc sponsored by SpinalMotion. The Kineflex/C is a metal-on-metal (cobalt chrome molybdenum alloy) cervical total disc replacement device. The Kineflex/C is... discectomy for intractable radiculopathy or myelopathy due to a single-level abnormality localized to the...

  16. 77 FR 42503 - Ophthalmic Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting

    Science.gov (United States)

    2012-07-19

    ... 301-977-8900. Contact Person: Natasha Facey, Center for Devices and Radiological Health, Food and Drug... who meet the following criteria: Adults, age 25 years or older. Bare light or no light perception in... perception, the retina must be able to respond to electrical stimulation as evidenced by an electrically...

  17. Wireless device monitoring systems and monitoring devices, and associated methods

    Science.gov (United States)

    McCown, Steven H; Derr, Kurt W; Rohde, Kenneth W

    2014-05-27

    Wireless device monitoring systems and monitoring devices include a communications module for receiving wireless communications of a wireless device. Processing circuitry is coupled with the communications module and configured to process the wireless communications to determine whether the wireless device is authorized or unauthorized to be present at the monitored area based on identification information of the wireless device. Methods of monitoring for the presence and identity of wireless devices are also provided.

  18. An innovative deployable solar panel system for Cubesats

    Science.gov (United States)

    Santoni, Fabio; Piergentili, Fabrizio; Donati, Serena; Perelli, Massimo; Negri, Andrea; Marino, Michele

    2014-02-01

    One of the main Cubesat bus limitations is the available on-board power. The maximum power obtained using body mounted solar panels and advanced triple junction solar cells on a triple unit Cubesat is typically less than 10 W. The Cubesat performance and the mission scenario opened to these small satellite systems could be greatly enhanced by an increase of the available power. This paper describes the design and realization of a modular deployable solar panel system for Cubesats, consisting of a modular hinge and spring system that can be potentially used on-board single (1U), double(2U), triple (3U) and six units (6U) Cubesats. The size of each solar panels is the size of a lateral Cubesat surface. The system developed is the basis for a SADA (Solar Array Drive Assembly), in which a maneuvering capability is added to the deployed solar array in order to follow the apparent motion of the sun. The system design trade-off is discussed, comparing different deployment concepts and architectures, leading to the final selection for the modular design. A prototype of the system has been realized for a 3U Cubesat, consisting of two deployable solar panel systems, made of three solar panels each, for a total of six deployed solar panels. The deployment system is based on a plastic fiber wire and thermal cutters, guaranteeing a suitable level of reliability. A test-bed for the solar panel deployment testing has been developed, supporting the solar array during deployment reproducing the dynamical situation in orbit. The results of the deployment system testing are discussed, including the design and realization of the test-bed, the mechanical stress given to the solar cells by the deployment accelerations and the overall system performance. The maximum power delivered by the system is about 50.4 W BOL, greatly enhancing the present Cubesat solar array performance.

  19. Performance evaluation of solar photovoltaic panel driven refrigeration system

    Science.gov (United States)

    Rajoria, C. S.; Singh, Dharmendra; Gupta, Pankaj Kumar

    2018-03-01

    The solar photovoltaic (PV) panel driven refrigeration system employs solar PV panel and play a vital role when combined with storage batteries. The variation in performance of solar PV panel driven refrigeration system has been experimentally investigated in this paper. The change in battery voltage is analyzed with respect to panel size. Different series and parallel combinations have been applied on four solar PV panels of 35W each to get 24V. With the above combination a current in the range of 3-5 ampere has been obtained depending upon the solar intensity. A refrigerator of 110 W and 50 liters is used in the present investigation which requires 0.80 ampere AC at 230 V. The required current and voltage has been obtained from an inverter which draws about 7 ampere DC from the battery bank at 24V. The compressor of the refrigerator consumed 110W which required a PV panel size of 176 W approximately. It is important to note that the compressor consumed about 300W for first 50 milliseconds, 130 W for next five seconds and gradually comes to 110 W in 65 seconds. Thus panel size should be such that it may compensate for the initial load requirement.

  20. Biomedical devices and systems security.

    Science.gov (United States)

    Arney, David; Venkatasubramanian, Krishna K; Sokolsky, Oleg; Lee, Insup

    2011-01-01

    Medical devices have been changing in revolutionary ways in recent years. One is in their form-factor. Increasing miniaturization of medical devices has made them wearable, light-weight, and ubiquitous; they are available for continuous care and not restricted to clinical settings. Further, devices are increasingly becoming connected to external entities through both wired and wireless channels. These two developments have tremendous potential to make healthcare accessible to everyone and reduce costs. However, they also provide increased opportunity for technology savvy criminals to exploit them for fun and profit. Consequently, it is essential to consider medical device security issues. In this paper, we focused on the challenges involved in securing networked medical devices. We provide an overview of a generic networked medical device system model, a comprehensive attack and adversary model, and describe some of the challenges present in building security solutions to manage the attacks. Finally, we provide an overview of two areas of research that we believe will be crucial for making medical device system security solutions more viable in the long run: forensic data logging, and building security assurance cases.

  1. Integrated thermal treatment systems study. Internal review panel report

    Energy Technology Data Exchange (ETDEWEB)

    Cudahy, J.; Escarda, T.; Gimpel, R. [and others

    1995-04-01

    The U.S. Department of Energy (DOE) Office of Technology Development (OTD) commissioned two studies to evaluate nineteen thermal treatment technologies for treatment of DOE mixed low-level waste. These studies were called the Integrated Thermal Treatment System (ITTS) Phase I and Phase II. With the help of the DOE Office of Environmental Management (EM) Mixed Waste Focus Group, OTD formed an ITTS Internal Review Panel to review and comment on the ITTS studies. This Panel was composed of scientists and engineers from throughout the DOE complex, the U.S. Environmental Protection Agency, the California EPA, and private experts. The Panel met from November 15-18, 1994 to review the ITTS studies and to make recommendations on the most promising thermal treatment systems for DOE mixed low-level wastes and on research and development necessary to prove the performance of the technologies. This report describes the findings and presents the recommendations of the Panel.

  2. Integrated thermal treatment systems study. Internal review panel report

    International Nuclear Information System (INIS)

    Cudahy, J.; Escarda, T.; Gimpel, R.

    1995-04-01

    The U.S. Department of Energy (DOE) Office of Technology Development (OTD) commissioned two studies to evaluate nineteen thermal treatment technologies for treatment of DOE mixed low-level waste. These studies were called the Integrated Thermal Treatment System (ITTS) Phase I and Phase II. With the help of the DOE Office of Environmental Management (EM) Mixed Waste Focus Group, OTD formed an ITTS Internal Review Panel to review and comment on the ITTS studies. This Panel was composed of scientists and engineers from throughout the DOE complex, the U.S. Environmental Protection Agency, the California EPA, and private experts. The Panel met from November 15-18, 1994 to review the ITTS studies and to make recommendations on the most promising thermal treatment systems for DOE mixed low-level wastes and on research and development necessary to prove the performance of the technologies. This report describes the findings and presents the recommendations of the Panel

  3. A CubeSat deployable solar panel system

    Science.gov (United States)

    McGuire, Thomas; Hirsch, Michael; Parsons, Michael; Leake, Skye; Straub, Jeremy

    2016-05-01

    The power usage of CubeSat's onboard systems has increased with the complexity of the systems included. This paper presents a deployment system design which creates a plane of solar panels to collect energy. This allows more panels to be in direct normal sunlight at any given point (in conjunction with the onboard attitude determination and control system), facilitating increased power generation. The deployable system is comprised of a printed circuit board (holding the solar cells) which is attached to an aluminum hinge. The efficacy of this approach for power generation and its simplicity, as compared to other prospective approaches, are assessed herein.

  4. Electromechanical systems and devices

    CERN Document Server

    Lyshevski, Sergey Edward

    2008-01-01

    ""The book begins with a good, well-written review of some of the basic equations used for electromechanical designs . . . There is very good technical depth to each of the sections in this book, giving the reader the ability to design real systems using the equations and examples from this book . . . aimed at electrical engineering students because it contains homework problems at the end of each chapter and is very instructive for power and electromechanical engineers."" - John J. Shea, in IEEE Electrical Insulation Magazine, March-April 2009, Vol. 25, No. 2

  5. Numerical optimization,modeling and system evaluation of a thermophotovoltaic hybrid panel

    OpenAIRE

    Greppi, Matteo

    2013-01-01

    Photovoltaic (PV) solar panels generally produce electricity in the 6% to 16% efficiency range, the rest being dissipated in thermal losses. To recover this amount, hybrid photovoltaic thermal systems (PVT) have been devised. These are devices that simultaneously convert solar energy into electricity and heat. It is thus interesting to study the PVT system globally from different point of views in order to evaluate advantages and disadvantages of this technology and its possible uses. In p...

  6. 77 FR 50701 - Radiological Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting

    Science.gov (United States)

    2012-08-22

    ..., sponsored by Hologic, Inc. The Selenia Dimensions 3D System is currently approved for breast cancer... synthetic 2D images from the DBT data. Hologic requests to expand the indications for use to allow the...

  7. Virtual panel for FOTIA control and information system

    International Nuclear Information System (INIS)

    Singh, S.K.; Kansara, M.J.; Padmini, S.; Ananthakrishnan, T.S.; Ghodgaonkar, M.D.

    2001-01-01

    Use of computers has provided an easy environment to tune machines like accelerators by integrating different subsystems and providing interface to control whole machine from a single node. Use of virtual panel in place of conventional shaft encoders and hard wired controls has provided an easy and efficient and interactive environment for accelerator operation. A graphical user interface is provided for system configuration (system data base change). FOTIA (Folded Tandem Ion Accelerator) is an indigenously designed accelerator at BARC. This paper describes the Virtual Panel features of the FOTIA Control and Information System. (author)

  8. Control System for Prosthetic Devices

    Science.gov (United States)

    Bozeman, Richard J. (Inventor)

    1996-01-01

    A control system and method for prosthetic devices is provided. The control system comprises a transducer for receiving movement from a body part for generating a sensing signal associated with that of movement. The sensing signal is processed by a linearizer for linearizing the sensing signal to be a linear function of the magnitude of the distance moved by the body part. The linearized sensing signal is normalized to be a function of the entire range of body part movement from the no-shrug position of the moveable body part through the full-shrg position of the moveable body part. The normalized signal is divided into a plurality of discrete command signals. The discrete command signals are used by typical converter devices which are in operational association with the prosthetic device. The converter device uses the discrete command signals for driving the moveable portions of the prosthetic device and its sub-prosthesis. The method for controlling a prosthetic device associated with the present invention comprises the steps of receiving the movement from the body part, generating a sensing signal in association with the movement of the body part, linearizing the sensing signal to be a linear function of the magnitude of the distance moved by the body part, normalizing the linear signal to be a function of the entire range of the body part movement, dividing the normalized signal into a plurality of discrete command signals, and implementing the plurality of discrete command signals for driving the respective moveable prosthesis device and its sub-prosthesis.

  9. 76 FR 4146 - Future Systems Technology Advisory Panel Meeting

    Science.gov (United States)

    2011-01-24

    ... SOCIAL SECURITY ADMINISTRATION [Docket No. SSA-2011-0010] Future Systems Technology Advisory Panel...: February 8, 2011, 10 a.m.-5 p.m., Location: The Latham Hotel, Presidential Ball Room. ADDRESSES: 3000 M... advice and recommendations on the future of systems technology and electronic services at the agency five...

  10. 75 FR 67804 - Future Systems Technology Advisory Panel Meeting

    Science.gov (United States)

    2010-11-03

    ... SOCIAL SECURITY ADMINISTRATION [Docket No. SSA-2010-0071] Future Systems Technology Advisory Panel...: December 13, 2010, 10 a.m.-5 p.m. Location: Omni Shoreham Hotel Washington, DC, Diplomat Room. ADDRESSES... recommendations on the future of systems technology and electronic services at the agency five to ten years into...

  11. Panel: Methodologies for multi-agent systems

    NARCIS (Netherlands)

    Kinny, David; Treur, Jan; Gasser, Les; Clark, Steve; Müller, Jörg

    1998-01-01

    Multi-Agent Systems technologies are migrating from research labs to software engineering centres. If these technologies are to realize their potential, it will become increasingly important to develop and employ methodologies, accessible to software engineers, for specifying, analysing, designing,

  12. Second generation precast deck panel (NUDECK) system.

    Science.gov (United States)

    2010-12-01

    "The majority of todays bridge decks are built using cast-in-place concrete construction. This is due to the perceived : low initial cost and constructor familiarity with the system. This research report describes the design, details, and : constr...

  13. Solar maximum mission panel jettison analysis remote manipulator system

    Science.gov (United States)

    Bauer, R. B.

    1980-01-01

    A study is presented of the development of the Remote Manipulator System (RMS) configurations for jettison of the solar panels on the Solar Maximum Mission/Multimission Satellite. A valid RMS maneuver between jettison configurations was developed. Arm and longeron loads and effector excursions due to the solar panel jettison were determined to see if they were within acceptable limits. These loads and end effector excursions were analyzed under two RMS modes, servos active in position hold submode, and in the brakes on mode.

  14. Microcontroller-based system for analyzing and characterizing solar panels

    International Nuclear Information System (INIS)

    Jabbar, Muhandis Abdul; Prawito

    2016-01-01

    A solar cell is one of many alternative energy which is still being developed and it works by converting sunlight into electricity. In order to use a solar cell, a deep knowledge about the solar cell’s characteristics is needed. The current and voltage (I-V) produced when the light hits the solar cell surface with a certain value of intensity and at a certain value of temperature becomes the basic study to determine solar cell characteristics. In the past decade, there were so many developments of devices to characterize solar cells and solar panels. One of them used a MOSFET device for varying electronic load to observe solar cell current and voltage responses. However, many devices which have been developed even device on the market using many expensive tools and quite complex. Therefore in this research, a simple low cost electronic controlled device for solar cell characterization is built based on MOSFET method and a microcontroller but still has high reliability and accuracy.

  15. Renewable Energy Devices and Systems

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Ionel, Dan M.

    2015-01-01

    In this paper, essential statistics demonstrating the increasing role of renewable energy generation are firstly discussed. A state of the art review section covers fundamentals of wind turbines and PV systems. Included are schematic diagrams illustrating the main components and system topologies...... and the fundamental and increasing role of power electronics as an enabler for renewable energy integration, and for the future power system and smart grid. Recent examples of research and development, including new devices and system installations for utility power plants, as well for as residential and commercial...... applications are provided. Fuel cells, solar thermal, wave generators, and energy storage systems are also briefly presented and illustrated. Challenges and future trends for 2025 are summarized in a table for on-shore and off-shore wind energy, solar power, including photovoltaic and concentering, wave energy...

  16. Integrated application of combined cooling, heating and power poly-generation PV radiant panel system of zero energy buildings

    Science.gov (United States)

    Yin, Baoquan

    2018-02-01

    A new type of combined cooling, heating and power of photovoltaic radiant panel (PV/R) module was proposed, and applied in the zero energy buildings in this paper. The energy system of this building is composed of PV/R module, low temperature difference terminal, energy storage, multi-source heat pump, energy balance control system. Radiant panel is attached on the backside of the PV module for cooling the PV, which is called PV/R module. During the daytime, the PV module was cooled down with the radiant panel, as the temperature coefficient influence, the power efficiency was increased by 8% to 14%, the radiant panel solar heat collecting efficiency was about 45%. Through the nocturnal radiant cooling, the PV/R cooling capacity could be 50 W/m2. For the multifunction energy device, the system shows the versatility during the heating, cooling and power used of building utilization all year round.

  17. A virtual control panel configuration tool for the X-Window system

    International Nuclear Information System (INIS)

    Hill, J.O.; Dalesio, L.R.; Kerstiens, D.M.

    1992-01-01

    Computer Graphics Workstations are becoming increasingly popular for use as virtual process control and read back panels. The workstation's CRT, keyboard, and pointing device are used in concert to produce a display that is in essence a control panel, even if actual switches and gauges are not present. The code behind these displays is most often specific to one display and not reusable for any other display. Recently, programs have been written allowing many of these virtual control panel displays to be configured without writing additional code. This approach allows the initial programming effort to be reapplied to many different display instances with minimal effort. These programs often incorporate many of the features of a graphics editor, allowing a pictorial model of the process under control to be incorporated into the control panel. We have just finished writing a second generation software system of this type for use with the X-window system and the Experimental Physics and Industrial Control System (EPICS). This paper describes the primary features of our software, the framework of our design, and our observations after initial installation. (author)

  18. Control system of fuel transporting device

    International Nuclear Information System (INIS)

    Yokota, Minoru.

    1981-01-01

    Purpose: To effectively avoid an obstacle in a fuel transporting device by reading the outputs of absolute position detectors mounted on movable trucks, controlling the movements of the trucks, and thereby smoothly and accurately positioning the fuel transporting device at predetermined position and providing a contact detector thereat. Method: The outputs from absolute position detectors which are mounted on a longitudinally movable truck and a laterally movable truck are input to an input/output control circuit. The input/output control circuit serves to compare, the position a fuel transporting device is to be moved to, with the present position on the basis of said input detection signal and a command signal from an operator console, to calculate the amount of movement to be driven, to produce an operation signal therefor to a control panel, and to drive and control the drive motors which are respectively mounted on the trucks for the fuel transfer device. On the other hand, in case that the transfer device comes into contact with an obstacle, the contact detector will immediately operate to produce a stop command through the control panel to the transporting device, and avoid a collision with the obstacle. (Yoshino, Y.)

  19. 75 FR 61509 - Notice of Issuance of Final Determination Concerning Solar Photovoltaic Panel Systems

    Science.gov (United States)

    2010-10-05

    ... Determination Concerning Solar Photovoltaic Panel Systems AGENCY: U.S. Customs and Border Protection, Department... Procurement; Title III, Trade Agreements Act of 1979; Country of Origin of solar photovoltaic panel system... solar photovoltaic (``PV'') panel systems contain both U.S. and foreign-origin raw materials and...

  20. Initiation devices, initiation systems including initiation devices and related methods

    Energy Technology Data Exchange (ETDEWEB)

    Daniels, Michael A.; Condit, Reston A.; Rasmussen, Nikki; Wallace, Ronald S.

    2018-04-10

    Initiation devices may include at least one substrate, an initiation element positioned on a first side of the at least one substrate, and a spark gap electrically coupled to the initiation element and positioned on a second side of the at least one substrate. Initiation devices may include a plurality of substrates where at least one substrate of the plurality of substrates is electrically connected to at least one adjacent substrate of the plurality of substrates with at least one via extending through the at least one substrate. Initiation systems may include such initiation devices. Methods of igniting energetic materials include passing a current through a spark gap formed on at least one substrate of the initiation device, passing the current through at least one via formed through the at least one substrate, and passing the current through an explosive bridge wire of the initiation device.

  1. Maximun power point tracker of photovoltaic s panels for stand alone systems

    International Nuclear Information System (INIS)

    Stoll, R; Manno, R

    2005-01-01

    The low energetic efficiency of photovoltaic s panels is known, in addition, due to the use of linear regulators, which dissipate an important bit of the generated energy, the efficiency of the photovoltaic systems is still smaller.Also, the I-V characteristic curve of the photovoltaic modules depends on the solar radiation and the own temperature; consequently, the maximum power point (Wp) changes permanently.In conclusion, to produce electricity with photovoltaic panels is very expensive. However due to preserve the environment this technology is widely used.With the purpose of optimizing the amount of energy produced by the photovoltaic system, two complementary methods are used.One is the Maximum Power Point Tracker (MPPT) system and the other one is the Solar Tracker system.The objective of this project is to reduce that cost increasing the amount of energy produced by the solar panels using a Maximum Power Point Tracker system.This device consists of a DC/DC buck converter of high performance, controlled by a PIC 16F873 micro controller; which carries out the conversions of the analogical signals of the solar array to digital signals (ADC), the PIC output digital signals to the PWM control of the power FET (DAC), and calculates the Duty Cycle (D) for the point of I-V curve where this product becomes maximum.Measurements for different loads and battery charges were made.With the obtained results, the comparisons with a conventional system were made, a greater cession of energy to the load is observed.The main conclusion of this work is: Using a MPPT device to making work the PV module during the greater possible time near the maximum power point, the efficiency of the photovoltaic systems can be increased

  2. 78 FR 25972 - Establishment of the Response Systems to Adult Sexual Crimes Panel

    Science.gov (United States)

    2013-05-03

    ... in Federal and State criminal courts, victim advocacy, treatment for victims, military justice, the... individuals do not count toward the Response Systems Panel's total membership nor do they have voting... to Adult Sexual Assault Crimes Panel membership about the Response System Panel's mission and...

  3. 77 FR 40735 - Unique Device Identification System

    Science.gov (United States)

    2012-07-10

    ... postmarket surveillance, and better security of devices through more effective detection and removal of... Drug Administration 21 CFR Parts 16, 801, 803, et al. Unique Device Identification System; Proposed..., 806, 810, 814, 820, 821, 822, and 830 [Docket No. FDA-2011-N-0090] RIN 0910-AG31 Unique Device...

  4. Experimental study of hydronic panels system and its environment

    Energy Technology Data Exchange (ETDEWEB)

    Diaz, Nestor Fonseca [University of Liege Belgium, Thermodynamics Laboratory, Campus du Sart Tilman, Bat: B49 - P33, B-4000 Liege (Belgium); Universidad Tecnologica de Pereira, Facultad de Ingenieria Mecanica (Colombia)

    2011-01-15

    An experimental analysis of hydronic cooling or heating ceiling panels coupled to the building is present in this investigation as a part of the commissioning study of this system. Two test chambers are adapted in a way to reproduce the interaction of the system to the building (windows, internal thermal loads distribution, building structure and ventilation). A series of experimental tests were performed in which the main objective is to observe the influence of parameters such as the water mass flow rate, supply water temperature, thermal load distribution, window and ventilation system effects on the hydronic ceiling capacity and comfort conditions. Test results show that the influence of asymmetric surfaces temperatures inside the room, especially the window effect is not negligible. Then, it is clear that the cooling hydronic ceiling must be evaluated coupled to the building systems and structure. (author)

  5. Experimental study of hydronic panels system and its environment

    Energy Technology Data Exchange (ETDEWEB)

    Fonseca Diaz, Nestor, E-mail: nestorfonseca5@hotmail.co [University of Liege Belgium, Thermodynamics Laboratory, Campus du Sart Tilman, Bat: B49 - P33, B-4000 Liege (Belgium); Universidad Tecnologica de Pereira, Facultad de Ingenieria Mecanica (Colombia)

    2011-01-15

    An experimental analysis of hydronic cooling or heating ceiling panels coupled to the building is present in this investigation as a part of the commissioning study of this system. Two test chambers are adapted in a way to reproduce the interaction of the system to the building (windows, internal thermal loads distribution, building structure and ventilation). A series of experimental tests were performed in which the main objective is to observe the influence of parameters such as the water mass flow rate, supply water temperature, thermal load distribution, window and ventilation system effects on the hydronic ceiling capacity and comfort conditions. Test results show that the influence of asymmetric surfaces temperatures inside the room, especially the window effect is not negligible. Then, it is clear that the cooling hydronic ceiling must be evaluated coupled to the building systems and structure.

  6. System reliability evaluation of a touch panel manufacturing system with defect rate and reworking

    International Nuclear Information System (INIS)

    Lin, Yi-Kuei; Huang, Cheng-Fu; Chang, Ping-Chen

    2013-01-01

    In recent years, portable consumer electronic products, such as cell phone, GPS, digital camera, tablet PC, and notebook are using touch panel as interface. With the demand of touch panel increases, performance assessment is essential for touch panel production. This paper develops a method to evaluate system reliability of a touch panel manufacturing system (TPMS) with defect rate of each workstation and takes reworking actions into account. The system reliability which evaluates the possibility of demand satisfaction can provide to managers with an understanding of the system capability and can indicate possible improvements. First, we construct a capacitated manufacturing network (CMN) for a TPMS. Second, a decomposition technique is developed to determine the input flow of each workstation based on the CMN. Finally, we generate the minimal capacity vectors that should be provided to satisfy the demand. The system reliability is subsequently evaluated in terms of the minimal capacity vectors. A further decision making issue is discussed to decide a reliable production strategy. -- Graphical abstract: The proposed procedure to evaluate system reliability of the touch panel manufacturing system (TPMS). Highlights: • The system reliability of a touch panel manufacturing system (TPMS) is evaluated. • The reworking actions are taken into account in the TPMS. • A capacitated manufacturing network is constructed for the TPMS. • A procedure is proposed to evaluate system reliability of TPMS

  7. Transparent Fingerprint Sensor System for Large Flat Panel Display

    Directory of Open Access Journals (Sweden)

    Wonkuk Seo

    2018-01-01

    Full Text Available In this paper, we introduce a transparent fingerprint sensing system using a thin film transistor (TFT sensor panel, based on a self-capacitive sensing scheme. An armorphousindium gallium zinc oxide (a-IGZO TFT sensor array and associated custom Read-Out IC (ROIC are implemented for the system. The sensor panel has a 200 × 200 pixel array and each pixel size is as small as 50 μm × 50 μm. The ROIC uses only eight analog front-end (AFE amplifier stages along with a successive approximation analog-to-digital converter (SAR ADC. To get the fingerprint image data from the sensor array, the ROIC senses a capacitance, which is formed by a cover glass material between a human finger and an electrode of each pixel of the sensor array. Three methods are reviewed for estimating the self-capacitance. The measurement result demonstrates that the transparent fingerprint sensor system has an ability to differentiate a human finger’s ridges and valleys through the fingerprint sensor array.

  8. Transparent Fingerprint Sensor System for Large Flat Panel Display.

    Science.gov (United States)

    Seo, Wonkuk; Pi, Jae-Eun; Cho, Sung Haeung; Kang, Seung-Youl; Ahn, Seong-Deok; Hwang, Chi-Sun; Jeon, Ho-Sik; Kim, Jong-Uk; Lee, Myunghee

    2018-01-19

    In this paper, we introduce a transparent fingerprint sensing system using a thin film transistor (TFT) sensor panel, based on a self-capacitive sensing scheme. An armorphousindium gallium zinc oxide (a-IGZO) TFT sensor array and associated custom Read-Out IC (ROIC) are implemented for the system. The sensor panel has a 200 × 200 pixel array and each pixel size is as small as 50 μm × 50 μm. The ROIC uses only eight analog front-end (AFE) amplifier stages along with a successive approximation analog-to-digital converter (SAR ADC). To get the fingerprint image data from the sensor array, the ROIC senses a capacitance, which is formed by a cover glass material between a human finger and an electrode of each pixel of the sensor array. Three methods are reviewed for estimating the self-capacitance. The measurement result demonstrates that the transparent fingerprint sensor system has an ability to differentiate a human finger's ridges and valleys through the fingerprint sensor array.

  9. Optimal design of sound absorbing systems with microperforated panels

    Science.gov (United States)

    Kim, Nicholas Nakjoo

    As the development of technology makes economic prosperity and life more convenient, people now desire a higher quality of life. This quality of life is based not only on the convenience in their life but also on clean and eco-friendly environments. To meet that requirement, much research is being performed in many areas of eco-friendly technology, such as renewable energy, biodegradable content, and batteries for electronic vehicles. This tendency is also obvious in the acoustics area, where there are continuing attempts to replace fiber-glass sound absorbers with fiber-free materials. The combination of microperfoated panels (MPP) (one of the fiber-free sound absorbing materials), usually in the form of a thin panel with small holes, and an air backing may be one of the preferred solutions. These panels can be designed in many ways, and usually feature many small (sub-millimeter) holes and typically surface porosities on the order of 1 percent. The detailed acoustical properties of MPPs depend on their hole shape, the hole diameter, the thickness of the panel, the overall porosity of the perforated film, the film's mass per unit area, and the depth of the backing air cavity. Together, these parameters control the absorption peak location and the magnitude of the absorption coefficient (and the magnitude of the transmission loss in barrier applications). By an appropriate choice of these parameters good absorption performance can be achieved in a frequency range one or two octaves wide. That kind of solution may be adequate when it is necessary to control sound only in a specified frequency range (in the speech interference range, for example). However, in order to provide appropriate noise control solutions over a broader range of frequencies, it is necessary to design systems featuring multiple-layers of MPPs, thus creating what amounts to a multi-degree-of-freedom system and so expanding the range over which good absorption can be obtained. In this research

  10. The development of an Infrared Environmental System for TOPEX Solar Panel Testing

    Science.gov (United States)

    Noller, E.

    1994-01-01

    Environmental testing and flight qualification of the TOPEX/POSEIDON spacecraft solar panels were performed with infrared (IR) lamps and a control system that were newly designed and integrated. The basic goal was more rigorous testing of the costly panels' new composite-structure design without jeopardizing their safety. The technique greatly reduces the costs and high risks of testing flight solar panels.

  11. Generic device controller for accelerator control systems

    International Nuclear Information System (INIS)

    Mariotti, R.; Buxton, W.; Frankel, R.; Hoff, L.

    1987-01-01

    A new distributed intelligence control system has become operational at the AGS for transport, injection, and acceleration of heavy ions. A brief description of the functionality of the physical devices making up the system is given. An attempt has been made to integrate the devices for accelerator specific interfacing into a standard microprocessor system, namely, the Universal Device Controller (UDC). The main goals for such a generic device controller are to provide: local computing power; flexibility to configure; and real time event handling. The UDC assemblies and software are described

  12. Data Base Management Systems Panel. Third workshop summary

    Science.gov (United States)

    Urena, J. L. (Editor)

    1981-01-01

    The discussions and results of a review by a panel of data base management system (DRMS) experts of various aspects of the use of DBMSs within NASA/Office of Space and Terrestrial Applications (OSTA) and related organizations are summarized. The topics discussed included the present status of the use of DBMS technology and of the various ongoing DBMS-related efforts within NASA. The report drafts of a study that seeks to determine the functional requirements for a generalized DBMS for the NASA/OSTA and related data bases are examined. Future problems and possibilities with the use of DBMS technology are also considered. A list of recommendations for NASA/OSTA data systems is included.

  13. 78 FR 27971 - Dental Products Panel of the Medical Devices Advisory Committee; Notice of Meeting

    Science.gov (United States)

    2013-05-13

    ... regulatory classification for dental devices known as Endosseous Dental Implants (Blade-form), one of the remaining preamendments Class III devices. The Class III blade-form endosseous dental implant is a device... endosseous dental implant into class II (special controls). The committee's discussion will involve making...

  14. Development of virtual touch panel system for operation at KEK-Electron Linac

    International Nuclear Information System (INIS)

    Kudou, T.; Kusano, S.; Furukawa, K.; Kamikubota, N.; Satoh, M.

    2004-01-01

    At the KEK Electron Linac, various operator interfaces are employed to keep its stable operation. Among these, the touch-panel system has been used to manipulate each equipment. However, maintenance of the touch-panel system became difficult for various reasons. A new operator interface on X Window was developed as a virtual touch-panel system with an improved operator interface. All the functions which are used in the old system were already ported. It is designed so that a new function can be added flexibly. The architecture of those old and new touch panel systems is described. (author)

  15. 75 FR 1396 - The General Hospital and Personal Use Devices Panel of the Medical Devices Advisory Committee...

    Science.gov (United States)

    2010-01-11

    ..., Salons C, D and E, 620 Perry Pkwy., Gaithersburg, MD. Contact Person: Tracy Phillips, Center for Devices... a disability, please contact AnnMarie Williams at 301-796-5966 at least 7 days in advance of the...

  16. Heat exchanger panel

    Science.gov (United States)

    Warburton, Robert E. (Inventor); Cuva, William J. (Inventor)

    2005-01-01

    The present invention relates to a heat exchanger panel which has broad utility in high temperature environments. The heat exchanger panel has a first panel, a second panel, and at least one fluid containment device positioned intermediate the first and second panels. At least one of the first panel and the second panel have at least one feature on an interior surface to accommodate the at least one fluid containment device. In a preferred embodiment, each of the first and second panels is formed from a high conductivity, high temperature composite material. Also, in a preferred embodiment, the first and second panels are joined together by one or more composite fasteners.

  17. Human health and ecological toxicity potentials due to heavy metal content in waste electronic devices with flat panel displays

    International Nuclear Information System (INIS)

    Lim, Seong-Rin; Schoenung, Julie M.

    2010-01-01

    Display devices such as cathode-ray tube (CRT) televisions and computer monitors are known to contain toxic substances and have consequently been banned from disposal in landfills in the State of California and elsewhere. New types of flat panel display (FPD) devices, millions of which are now purchased each year, also contain toxic substances, but have not previously been systematically studied and compared to assess the potential impact that could result from their ultimate disposal. In the current work, the focus is on the evaluation of end-of-life toxicity potential from the heavy metal content in select FPD devices with the intent to inform material selection and design-for-environment (DfE) decisions. Specifically, the metals antimony, arsenic, barium, beryllium, cadmium, chromium, cobalt, copper, lead, mercury, molybdenum, nickel, selenium, silver, vanadium, and zinc in plasma TVs, LCD (liquid crystal display) TVs, LCD computer monitors and laptop computers are considered. The human health and ecotoxicity potentials are evaluated through a life cycle assessment perspective by combining data on the respective heavy metal contents, the characterization factors in the U.S. EPA Tool for the Reduction and Assessment of Chemical and other environmental Impacts (TRACI), and a pathway and impact model. Principal contributors to the toxicity potentials are lead, arsenic, copper, and mercury. Although the heavy metal content in newer flat panel display devices creates less human health toxicity potential than that in CRTs, for ecological toxicity, the new devices are worse, especially because of the mercury in LCD TVs and the copper in plasma TVs.

  18. Human health and ecological toxicity potentials due to heavy metal content in waste electronic devices with flat panel displays.

    Science.gov (United States)

    Lim, Seong-Rin; Schoenung, Julie M

    2010-05-15

    Display devices such as cathode-ray tube (CRT) televisions and computer monitors are known to contain toxic substances and have consequently been banned from disposal in landfills in the State of California and elsewhere. New types of flat panel display (FPD) devices, millions of which are now purchased each year, also contain toxic substances, but have not previously been systematically studied and compared to assess the potential impact that could result from their ultimate disposal. In the current work, the focus is on the evaluation of end-of-life toxicity potential from the heavy metal content in select FPD devices with the intent to inform material selection and design-for-environment (DfE) decisions. Specifically, the metals antimony, arsenic, barium, beryllium, cadmium, chromium, cobalt, copper, lead, mercury, molybdenum, nickel, selenium, silver, vanadium, and zinc in plasma TVs, LCD (liquid crystal display) TVs, LCD computer monitors and laptop computers are considered. The human health and ecotoxicity potentials are evaluated through a life cycle assessment perspective by combining data on the respective heavy metal contents, the characterization factors in the U.S. EPA Tool for the Reduction and Assessment of Chemical and other environmental Impacts (TRACI), and a pathway and impact model. Principal contributors to the toxicity potentials are lead, arsenic, copper, and mercury. Although the heavy metal content in newer flat panel display devices creates less human health toxicity potential than that in CRTs, for ecological toxicity, the new devices are worse, especially because of the mercury in LCD TVs and the copper in plasma TVs. Copyright (c) 2009 Elsevier B.V. All rights reserved.

  19. Microwave Feeding System Devices Of Linear Collider

    CERN Document Server

    Bogdanovich, B Yu; Kaminsky, V I; Lalayan, M V; Sobenin, N P; Zavadtsev, D A

    2004-01-01

    The simulations, manufacturing and experimental results for two devices of linear collider RF power distribution system are presented. One of these devices is magic tee with movable choke plungers in E- and H-arms for the tuning the coupling-factor and RF phase of highpower accelerating cavities. The QEXT

  20. Adaptive Device Context Based Mobile Learning Systems

    Science.gov (United States)

    Pu, Haitao; Lin, Jinjiao; Song, Yanwei; Liu, Fasheng

    2011-01-01

    Mobile learning is e-learning delivered through mobile computing devices, which represents the next stage of computer-aided, multi-media based learning. Therefore, mobile learning is transforming the way of traditional education. However, as most current e-learning systems and their contents are not suitable for mobile devices, an approach for…

  1. Advances in memristors, memristive devices and systems

    CERN Document Server

    Volos, Christos

    2017-01-01

    This book reports on the latest advances in and applications of memristors, memristive devices and systems. It gathers 20 contributed chapters by subject experts, including pioneers in the field such as Leon Chua (UC Berkeley, USA) and R.S. Williams (HP Labs, USA), who are specialized in the various topics addressed in this book, and covers broad areas of memristors and memristive devices such as: memristor emulators, oscillators, chaotic and hyperchaotic memristive systems, control of memristive systems, memristor-based min-max circuits, canonic memristors, memristive-based neuromorphic applications, implementation of memristor-based chaotic oscillators, inverse memristors, linear memristor devices, delayed memristive systems, flux-controlled memristive emulators, etc. Throughout the book, special emphasis is given to papers offering practical solutions and design, modeling, and implementation insights to address current research problems in memristors, memristive devices and systems. As such, it offers a va...

  2. Machine Vision System for Color Sorting Wood Edge-Glued Panel Parts

    Science.gov (United States)

    Qiang Lu; S. Srikanteswara; W. King; T. Drayer; Richard Conners; D. Earl Kline; Philip A. Araman

    1997-01-01

    This paper describes an automatic color sorting system for hardwood edge-glued panel parts. The color sorting system simultaneously examines both faces of a panel part and then determines which face has the "better" color given specified color uniformity and priority defined by management. The real-time color sorting system software and hardware are briefly...

  3. 78 FR 30928 - General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee; Notice of...

    Science.gov (United States)

    2013-05-23

    ... integral sharps injury prevention feature is for single use only, disposable blood lancet with a blade attached to a solid base which includes an integral sharps injury prevention feature that allows the device... puncture the skin to obtain a drop of blood for diagnostic purposes; Blood lancet without an integral...

  4. 75 FR 1395 - General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee; Amendment of...

    Science.gov (United States)

    2010-01-11

    ... and Radiological Health, Food and Drug Administration, 10903 New Hampshire Ave., White Oak 66, rm..., Center for Devices and Radiological Health, Food and Drug Administration, 10903 New Hampshire Ave., White... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2009-N-0606...

  5. System and method for networking electrochemical devices

    Science.gov (United States)

    Williams, Mark C.; Wimer, John G.; Archer, David H.

    1995-01-01

    An improved electrochemically active system and method including a plurality of electrochemical devices, such as fuel cells and fluid separation devices, in which the anode and cathode process-fluid flow chambers are connected in fluid-flow arrangements so that the operating parameters of each of said plurality of electrochemical devices which are dependent upon process-fluid parameters may be individually controlled to provide improved operating efficiency. The improvements in operation include improved power efficiency and improved fuel utilization in fuel cell power generating systems and reduced power consumption in fluid separation devices and the like through interstage process fluid parameter control for series networked electrochemical devices. The improved networking method includes recycling of various process flows to enhance the overall control scheme.

  6. Reliability of microtechnology interconnects, devices and systems

    CERN Document Server

    Liu, Johan; Sarkka, Jussi; Tegehall, Per-Erik; Andersson, Cristina

    2011-01-01

    This text discusses the reliability of microtechnology products from the bottom up, beginning with devices and extending to systems. It covers many topics, and it addresses specific failure modes in solder and conductive adhesives at great length.

  7. Micro and smart devices and systems

    CERN Document Server

    Ananthasuresh, G; Pratap, Rudra; Krupanidhi, S

    2014-01-01

    The book presents cutting-edge research in the emerging fields of micro, nano, and smart devices and systems from experts working in these fields over the last decade. Most of the contributors have built devices or systems or developed processes or algorithms in these areas. The book is a unique collection of chapters from different areas with a common theme and is immensely useful to academic researchers and practitioners in the industry who work in this field.

  8. Safety status system for operating room devices.

    Science.gov (United States)

    Guédon, Annetje C P; Wauben, Linda S G L; Overvelde, Marlies; Blok, Joleen H; van der Elst, Maarten; Dankelman, Jenny; van den Dobbelsteen, John J

    2014-01-01

    Since the increase of the number of technological aids in the operating room (OR), equipment-related incidents have come to be a common kind of adverse events. This underlines the importance of adequate equipment management to improve the safety in the OR. A system was developed to monitor the safety status (periodic maintenance and registered malfunctions) of OR devices and to facilitate the notification of malfunctions. The objective was to assess whether the system is suitable for use in an busy OR setting and to analyse its effect on the notification of malfunctions. The system checks automatically the safety status of OR devices through constant communication with the technical facility management system, informs the OR staff real-time and facilitates notification of malfunctions. The system was tested for a pilot period of six months in four ORs of a Dutch teaching hospital and 17 users were interviewed on the usability of the system. The users provided positive feedback on the usability. For 86.6% of total time, the localisation of OR devices was accurate. 62 malfunctions of OR devices were reported, an increase of 12 notifications compared to the previous year. The safety status system was suitable for an OR complex, both from a usability and technical point of view, and an increase of reported malfunctions was observed. The system eases monitoring the safety status of equipment and is a promising tool to improve the safety related to OR devices.

  9. Compact Active Vibration Control System for a Flexible Panel

    Science.gov (United States)

    Schiller, Noah H. (Inventor); Cabell, Randolph H. (Inventor); Perey, Daniel F. (Inventor)

    2014-01-01

    A diamond-shaped actuator for a flexible panel has an inter-digitated electrode (IDE) and a piezoelectric wafer portion positioned therebetween. The IDE and/or the wafer portion are diamond-shaped. Point sensors are positioned with respect to the actuator and measure vibration. The actuator generates and transmits a cancelling force to the panel in response to an output signal from a controller, which is calculated using a signal describing the vibration. A method for controlling vibration in a flexible panel includes connecting a diamond-shaped actuator to the flexible panel, and then connecting a point sensor to each actuator. Vibration is measured via the point sensor. The controller calculates a proportional output voltage signal from the measured vibration, and transmits the output signal to the actuator to substantially cancel the vibration in proximity to each actuator.

  10. Embedded nonvolatile memory devices with various silicon nitride energy band gaps on glass used for flat panel display applications

    International Nuclear Information System (INIS)

    Son, Dang Ngoc; Van Duy, Nguyen; Jung, Sungwook; Yi, Junsin

    2010-01-01

    Nonvolatile memory (NVM) devices with a nitride–nitride–oxynitride stack structure on a rough poly-silicon (poly-Si) surface were fabricated using a low-temperature poly-Si (LTPS) thin film transistor technology on glass substrates for application of flat panel display (FPD). The plasma-assisted oxidation/nitridation method is used to form a uniform oxynitride with an ultrathin tunneling layer on a rough LTPS surface. The NVMs, using a Si-rich silicon nitride film as a charge-trapping layer, were proposed as one of the solutions for the improvement of device performance such as the program/erase speed, the memory window and the charge retention characteristics. To further improve the vertical scaling and charge retention characteristics of NVM devices, the high-κ high-density N-rich SiN x films are used as a blocking layer. The fabricated NVM devices have outstanding electrical properties, such as a low threshold voltage, a high ON/OFF current ratio, a low subthreshold swing, a low operating voltage of less than ±9 V and a large memory window of 3.7 V, which remained about 1.9 V over a period of 10 years. These characteristics are suitable for electrical switching and data storage with in FPD application

  11. Detailed design report for an operational phase panel-closure system

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-01-11

    Under contract to Westinghouse Electric Corporation (Westinghouse), Waste Isolation Division (WID), IT Corporation has prepared a detailed design of a panel-closure system for the Waste Isolation Pilot Plant (WIPP). Preparation of this detailed design of an operational-phase closure system is required to support a Resource Conservation and Recovery Act (RCRA) Part B permit application and a non-migration variance petition. This report describes the detailed design for a panel-closure system specific to the WIPP site. The recommended panel-closure system will adequately isolate the waste-emplacement panels for at least 35 years. This report provides detailed design and material engineering specifications for the construction, emplacement, and interface-grouting associated with a panel-closure system at the WIPP repository, which would ensure that an effective panel-closure system is in place for at least 35 years. The panel-closure system provides assurance that the limit for the migration of volatile organic compounds (VOC) will be met at the point of compliance, the WIPP site boundary. This assurance is obtained through the inherent flexibility of the panel-closure system.

  12. Detailed design report for an operational phase panel-closure system

    International Nuclear Information System (INIS)

    1996-01-01

    Under contract to Westinghouse Electric Corporation (Westinghouse), Waste Isolation Division (WID), IT Corporation has prepared a detailed design of a panel-closure system for the Waste Isolation Pilot Plant (WIPP). Preparation of this detailed design of an operational-phase closure system is required to support a Resource Conservation and Recovery Act (RCRA) Part B permit application and a non-migration variance petition. This report describes the detailed design for a panel-closure system specific to the WIPP site. The recommended panel-closure system will adequately isolate the waste-emplacement panels for at least 35 years. This report provides detailed design and material engineering specifications for the construction, emplacement, and interface-grouting associated with a panel-closure system at the WIPP repository, which would ensure that an effective panel-closure system is in place for at least 35 years. The panel-closure system provides assurance that the limit for the migration of volatile organic compounds (VOC) will be met at the point of compliance, the WIPP site boundary. This assurance is obtained through the inherent flexibility of the panel-closure system

  13. Performance evaluation of an automatic positioning system for photovoltaic panels; Avaliacao de desempenho de um sistema de posicionamento automatico para paineis fotovoltaicos

    Energy Technology Data Exchange (ETDEWEB)

    Alves, Alceu Ferreira; Cagnon, Jose Angelo [Universidade Estadual Paulista (FEB/UNESP), Bauru, SP (Brazil). Fac. de Engenharia], Emails: alceu@feb.unesp.br, jacagnon@feb.unesp.br

    2009-07-01

    The need of using electric energy in localities not attended by the utilities has motivated the development of this research, whose main approach was photovoltaic systems and the search for better performance of these systems with the solar panels positioning toward the sun. This work presents the performance evaluation of an automatic positioning system for photovoltaic panels taking in account the increase in generation of electric energy and its costs of implantation. It was designed a simplified electromechanical device, which is able to support and to move a photovoltaic panel along the day and along the year, keeping its surface aimed to the sun rays, without using sensors and with optimization of movements, due the adjustment of panel's inclination take place only once a day. The obtained results indicated that the proposal is viable, showing a compatible cost compared to the increase in the generation of electricity. (author)

  14. Wireless device monitoring methods, wireless device monitoring systems, and articles of manufacture

    Science.gov (United States)

    McCown, Steven H [Rigby, ID; Derr, Kurt W [Idaho Falls, ID; Rohde, Kenneth W [Idaho Falls, ID

    2012-05-08

    Wireless device monitoring methods, wireless device monitoring systems, and articles of manufacture are described. According to one embodiment, a wireless device monitoring method includes accessing device configuration information of a wireless device present at a secure area, wherein the device configuration information comprises information regarding a configuration of the wireless device, accessing stored information corresponding to the wireless device, wherein the stored information comprises information regarding the configuration of the wireless device, comparing the device configuration information with the stored information, and indicating the wireless device as one of authorized and unauthorized for presence at the secure area using the comparing.

  15. 47 CFR 15.115 - TV interface devices, including cable system terminal devices.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 1 2010-10-01 2010-10-01 false TV interface devices, including cable system... FREQUENCY DEVICES Unintentional Radiators § 15.115 TV interface devices, including cable system terminal devices. (a) Measurements of the radiated emissions of a TV interface device shall be conducted with the...

  16. Light-emitting device test systems

    Science.gov (United States)

    McCord, Mark; Brodie, Alan; George, James; Guan, Yu; Nyffenegger, Ralph

    2018-01-23

    Light-emitting devices, such as LEDs, are tested using a photometric unit. The photometric unit, which may be an integrating sphere, can measure flux, color, or other properties of the devices. The photometric unit may have a single port or both an inlet and outlet. Light loss through the port, inlet, or outlet can be reduced or calibrated for. These testing systems can provide increased reliability, improved throughput, and/or improved measurement accuracy.

  17. Biometric Authentication System on Mobile Personal Devices

    NARCIS (Netherlands)

    Tao, Q.; Veldhuis, Raymond N.J.

    We propose a secure, robust, and low-cost biometric authentication system on the mobile personal device for the personal network. The system consists of the following five key modules: 1) face detection; 2) face registration; 3) illumination normalization; 4) face verification; and 5) information

  18. 49 CFR 571.118 - Standard No. 118; Power-operated window, partition, and roof panel systems.

    Science.gov (United States)

    2010-10-01

    ...-operated window, partition, and roof panel systems. S1. Purpose and scope. This standard specifies requirements for power operated window, partition, and roof panel systems to minimize the likelihood of death.... S5. Automatic reversal systems. A power-operated window, partition, or roof panel system that is...

  19. Stretchable bioelectronics for medical devices and systems

    CERN Document Server

    Ghaffari, Roozbeh; Kim, Dae-Hyeong

    2016-01-01

    This book highlights recent advances in soft and stretchable biointegrated electronics. A renowned group of authors address key ideas in the materials, processes, mechanics, and devices of soft and stretchable electronics; the wearable electronics systems; and bioinspired and implantable biomedical electronics. Among the topics discussed are liquid metals, stretchable and flexible energy sources, skin-like devices, in vitro neural recording, and more. Special focus is given to recent advances in extremely soft and stretchable bio-inspired electronics with real-world clinical studies that validate the technology. Foundational theoretical and experimental aspects are also covered in relation to the design and application of these biointegrated electronics systems. This is an ideal book for researchers, engineers, and industry professionals involved in developing healthcare devices, medical tools and related instruments relevant to various clinical practices.

  20. Apparatuses, Systems and Methods for Cleaning Photovoltaic Devices

    KAUST Repository

    Eitelhuber, Georg

    2013-02-14

    Embodiments of solar panel cleaning apparatuses, solar panel cleaning systems, and solar panel cleaning methods are disclosed. In certain embodiments, the disclosed solar panel cleaning apparatuses, systems and methods do may not require any water or other cleaning liquids in the whole cleaning process, which makes them prominent well suited in for water-deficit environments such as deserts. In one embodiment, the solar panel cleaning apparatus comprises one or more rotatable brushes each having a rotational axis and a drive configured to move each of the one or more rotatable brushes in a direction that is not perpendicular to the rotational axis. The solar panel cleaning apparatus is may be configured such that the angle of the rotational axis of at least one of the one or more rotatable brushes is adjustable relative to the direction of travel.

  1. Practice-based PREP Panel handling evaluation of a new impression mixing device and the associated material.

    Science.gov (United States)

    Burke, F J Trevor; Crisp, Russell J; Klettke, Thomas

    2011-12-01

    To evaluate the handling of a new impression mixing device and the associated impression material by general dental practitioner members of the PREP Panel. By means of a questionnaire, the participating practitioners recorded their views on the mixing machine and impression materials, having used these for ten weeks. UK general dental practices. General dental practitioner members of a UK practice-based research group. A questionnaire was designed to elicit views on the performance of the mixing device and impression material under test. This was distributed to the practitioners who had used the test materials for 10 weeks and the data thereby obtained collated and presented, principally in the form of VAS scales. Rating of various parameters of the mixing device and impression materials on VAS scales. The Pentamix 3 machine scored well for ease of initial use [4.8 on a visual analogue scale (VAS) where 1 = very difficult to use and 5 = very easy to use]. In a range of criteria (including cleanliness, easy handling, time to fill the tray and overall convenience) the Pentamix scored highly on VAS scales. A maximum score of 5 (on a VAS where 1 = very dissatisfied and 5 = very satisfied) was achieved for reproducible mixing quality. The appreciation of the Pentamix 3 mixing machine was demonstrated by the fact that 85% (n = 11) of evaluators stated that they would recommend it to colleagues. Regarding the impression material under evaluation, 85% (n = 11) of the evaluators stated that they would recommend Impregum Quick impression materials to their colleagues. Within the limitations of this study, the Pentamix 3 automatic impression mixing device scored highly in this assessment, together with the impression materials assessed. © 2011 FDI World Dental Federation.

  2. Control system and method for prosthetic devices

    Science.gov (United States)

    Bozeman, Richard J., Jr. (Inventor)

    1992-01-01

    A control system and method for prosthetic devices is provided. The control system comprises a transducer for receiving movement from a body part for generating a sensing signal associated with that movement. The sensing signal is processed by a linearizer for linearizing the sensing signal to be a linear function of the magnitude of the distance moved by the body part. The linearized sensing signal is normalized to be a function of the entire range of body part movement from the no-shrug position of the movable body part through the full-shrug position of the movable body part. The normalized signal is divided into a plurality of discrete command signals. The discrete command signals are used by typical converter devices which are in operational association with the prosthetic device. The converter device uses the discrete command signals for driving the movable portions of the prosthetic device and its sub-prosthesis. The method for controlling a prosthetic device associated with the present invention comprises the steps of receiving the movement from the body part, generating a sensing signal in association with the movement of the body part, linearizing the sensing signal to be a linear function of the magnitude of the distance moved by the body part, normalizing the linear signal to be a function of the entire range of the body part movement, dividing the normalized signal into a plurality of discrete command signals, and implementing the plurality of discrete command signals for driving the respective movable prosthesis device and its sub-prosthesis.

  3. Technologies and devices for micro chemical systems

    NARCIS (Netherlands)

    Gardeniers, Johannes G.E.; Schasfoort, Richardus B.M.; van den Berg, Albert

    2000-01-01

    This article describes recent developments at MESA+ in the field of miniaturised systems for chemical synthesis and analysis, also frequently referred to as "Lab-on-a-Chip". Several examples of siliconbased devices will be discussed, like micro pipettes for DNA studies, chips for cation analysis in

  4. 76 FR 8637 - Medical Devices; Medical Device Data Systems

    Science.gov (United States)

    2011-02-15

    ... used for, the design, manufacture, packaging, labeling, storage, installation, and servicing of devices... practitioners; and health care and consumer advocacy organizations, including individual physicians and hospital...

  5. Automated Intelligent Monitoring and the Controlling Software System for Solar Panels

    Science.gov (United States)

    Nalamwar, H. S.; Ivanov, M. A.; Baidali, S. A.

    2017-01-01

    The inspection of the solar panels on a periodic basis is important to improve longevity and ensure performance of the solar system. To get the most solar potential of the photovoltaic (PV) system is possible through an intelligent monitoring & controlling system. The monitoring & controlling system has rapidly increased its popularity because of its user-friendly graphical interface for data acquisition, monitoring, controlling and measurements. In order to monitor the performance of the system especially for renewable energy source application such as solar photovoltaic (PV), data-acquisition systems had been used to collect all the data regarding the installed system. In this paper the development of a smart automated monitoring & controlling system for the solar panel is described, the core idea is based on IoT (the Internet of Things). The measurements of data are made using sensors, block management data acquisition modules, and a software system. Then, all the real-time data collection of the electrical output parameters of the PV plant such as voltage, current and generated electricity is displayed and stored in the block management. The proposed system is smart enough to make suggestions if the panel is not working properly, to display errors, to remind about maintenance of the system through email or SMS, and to rotate panels according to a sun position using the Ephemeral table that stored in the system. The advantages of the system are the performance of the solar panel system which can be monitored and analyzed.

  6. Analysis and Design of CLL Resonant Converter for Solar Panel-battery Systems

    OpenAIRE

    D.Ramasubramanian; C.Nagarajan; M.Muruganandam

    2012-01-01

    This paper presents a CLL resonant converter with DSP based Fuzzy Logic Controller (FLC) for solar panel to battery charging system. The mathematical model of the converters has been developed and simulated using MATLAB. The state space model of the converter is developed; it is used to analysis the steady state stability of the system. The aim of the proposed converter is to regulate and control of the output voltage from the solar panel voltage. The performance of the proposed converter is ...

  7. A study on development of virtual panel and virtual collaboration system

    International Nuclear Information System (INIS)

    Yoo, H. J.; Park, S. Y.; Lee, M. S.; Hong, J. H.

    2001-01-01

    The Nuclear I and C group of KEPRI has been peforming research and development on the VRCATS, Virtual Reality based Computer Assisted Training System. For the past two years, we have developed the first VRCATS for Youngkwang 1 nuclear power plant. Currently, we are developing an advanced VRCATS for Uljin 3 nuclear power plant. In this paepr, we will describe virtual panel system and VR based collaborate training system (VRCATS) of the Uljin VRCATS. Since Virtual Panel provides the same environment as the real MCR, trainees can expect the same training effect with Virtual Panel as they do with full scope simulator. i.e., trainees can check key variables and operate the plants and get responses with Virtual Panel. VRCTS provides another realistic training environment for trainees. In VRCATS, for example, operators in a group can work together t handle LOCA (Loss of Coolant Accident) according to emergency operation procedures

  8. Dynamic heat transfer modeling and parametric study of thermoelectric radiant cooling and heating panel system

    International Nuclear Information System (INIS)

    Luo, Yongqiang; Zhang, Ling; Liu, Zhongbing; Wang, Yingzi; Wu, Jing; Wang, Xiliang

    2016-01-01

    Highlights: • Dynamic model of thermoelectric radiant panel system is established. • The internal parameters of thermoelectric module are dynamically calculated in simulation. • Both artificial neural networks model and system model are verified through experiment data. • Optimized system structure is obtained through parametric study. - Abstract: Radiant panel system can optimize indoor thermal comfort with lower energy consumption. The thermoelectric radiant panel (TERP) system is a new and effective prototype of radiant system using thermoelectric module (TEM) instead of conventional water pipes, as heat source. The TERP can realize more stable and easier system control as well as lower initial and operative cost. In this study, an improved system dynamic model was established by combining analytical system model and artificial neural networks (ANN) as well as the dynamic calculation functions of internal parameters of TEM. The double integral was used for the calculation of surface average temperature of TERP. The ANN model and system model were in good agreement with experiment data in both cooling and heating mode. In order to optimize the system design structure, parametric study was conducted in terms of the thickness of aluminum panel and insulation, as well as the arrangement of TEMs on the surface of radiant panel. It was found through simulation results that the optimum thickness of aluminum panel and insulation are respectively around 1–2 mm and 40–50 mm. In addition, TEMs should be uniformly installed on the surface of radiant panel and each TEM should stand at the central position of a square-shaped typical region with length around 0.387–0.548 m.

  9. Performance power evaluation of DC fan cooling system for PV panel by using ANSYS CFX

    Science.gov (United States)

    Syafiqah, Z.; Amin, N. A. M.; Irwan, Y. M.; Irwanto, M.; Leow, W. Z.; Amelia, A. R.

    2017-09-01

    A research has been conducted to find the optimum combination for DC fan air cooling system of photovoltaic (PV) panel. During normal operation of PV panel, it is estimated that only 15 % of solar radiation is converted into electrical energy. Meanwhile, the rest of the solar radiation is converted into heat energy which affects the performance of the PV panel. Therefore, the aim of this research is to investigate the performance power evaluation of DC fan cooling system for PV panel by using ANSYS CFX. The effect of airflow configuration of DC fan has been investigated. This is to analyze whether the airflow circulation of DC fan cause a change towards the maximum temperature of PV panel. Besides, the impact of varying number of DC fans attached at the back of PV panel is evaluated. The result of airflow circulation of DC fan has been discussed. Meanwhile, with the increment number of DC fans, the PV panel temperature drops significantly. As a conclusion, the optimum number of DC fans is two with the combination of inlet airflow.

  10. Stationary Optical Concentrator Designs and Wafer Scale Monolithic Integration of Semiconductor Devices for Next Generation Photovoltaic Panels

    Science.gov (United States)

    Kim, Jung Min

    A major barrier in utilizing solar energy for large scale deployment is the cost of the photovoltaic (PV) systems. Several approaches have been used for the cost reduction such as by modifying PV system designs in addition to enhancing the efficiency of solar cells. Due to the high cost of materials, minimizing the use of solar cells such as in concentrator type systems is highly attractive for reducing the cost of the PV modules by focusing the incident light onto the PV cell. However concentrator PV systems (CPV) require constant tracking of the sun and hence are complex in design and expensive to operate, except in limited situations such as large scale PV power plants. It is desirable to design new concentrator type systems that do not require continuous tracking of the sun. These systems could ultimately reduce the PV system cost to a minimum while maximizing the power conversion efficiency. In this thesis we propose a simple design for a stationary concentrator photovoltaic (SCPV) system that could significantly reduce the cost of generating electricity using PV devices. Using optical ray tracing simulations, we have been able to design SCPV systems that could reduce the PV module cost by 2--10 times without compromising on the power conversion efficiency of the system. Another alternative approach for sustainable high efficiency PV system design is to develop low cost PV cells for terrestrial applications. To meet the demands of low cost and large scale production, larger and thinner (or flexible) substrates are required. We demonstrated the feasibility of fabricating monolithic interconnected PV devices at the wafer scale (2 inch wafers). In this study, GaSb PV cells grown on semi-insulating GaAs were used as the model material. Crucial device fabrication steps such as a selective etching process have been developed that is necessary for isolating individual devices on the wafer and interconnecting them with sub-micron scale accuracy. Selective etching of

  11. Low-power-consumption flat-panel light-emitting device driven by field-emission electron source using high-crystallinity single-walled carbon nanotubes

    Science.gov (United States)

    Shimoi, Norihiro; Abe, Daisuke; Matsumoto, Kazuyuki; Sato, Yoshinori; Tohji, Kazuyuki

    2017-06-01

    Thin electrode films assembled through a wet process using single-walled carbon nanotubes (SWCNTs) are expected to play a role in reducing power consumption and saving energy in field-emission electron sources. The flat-panel light-emitting device for this study featured a line-sequential-scanning-type electrode structure equipped with electrodes for on-and-off controls of electron emissions, on which high-crystallinity SWCNTs were uniformly distributed. The device successfully emitted electrons on the flat panel in a stable manner. A technology for amplifying the luminance output by controlling the persistence characteristics of a fluorescent screen was also successfully developed. By combining such elemental technologies, a flat-panel light-emission device, as a stand-alone planar lighting device, which achieves a high-luminance efficiency of 87 lm/W and energy-conserved driving, was assembled for the first time in the world. The creation of field-emission electron sources driven with ultralow power consumption, along with applications that utilize such devices, is expected in the future.

  12. 78 FR 55081 - Circulatory System Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting

    Science.gov (United States)

    2013-09-09

    ..., and D, 620 Perry Pkwy., Gaithersburg, MD 20877. The hotel's telephone number is 301-977-8900. Contact... of the trial was to demonstrate that the time until the first event of all-cause mortality, heart... special needs. If you require special accommodations due to a disability, please contact AnnMarie Williams...

  13. 77 FR 25183 - Circulatory System Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting

    Science.gov (United States)

    2012-04-27

    ... guidewire and to track the bioprosthesis over the aortic arch and for crossing and positioning in the native...-dilate the native annulus) and a crimper. FDA intends to make background material available to the public... Advisory Committee Act (5 U.S.C. app. 2). Dated: April 19, 2012. Jill Hartzler Warner, Acting Associate...

  14. 76 FR 36548 - Circulatory System Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting

    Science.gov (United States)

    2011-06-22

    ... track the bioprosthesis over the aortic arch and for crossing and positioning in the native valve. The... native annulus) and a crimper. On July 21, 2011, the committee will discuss, make recommendations, and... Federal Advisory Committee Act (5 U.S.C. app. 2). Dated: June 15, 2011. Jill Hartzler Warner, Acting...

  15. 77 FR 66847 - Circulatory System Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting

    Science.gov (United States)

    2012-11-07

    ...: (1) Centrifugal type pumps utilize a rotor to impart energy to the blood in an extracorporeal circuit... cardiopulmonary blood pumps for use in cardiopulmonary bypass circuits for periods of up to six hours. Micro... blood pumps for use in cardiopulmonary bypass circuits for periods of up to six hours, but FDA did not...

  16. 76 FR 56200 - Circulatory System Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting

    Science.gov (United States)

    2011-09-12

    ... lesion lengths per patient of 280 mm. \\1\\ ``Fr'' stands for French. It is a term that defines the... registrants requesting to speak is greater than can be reasonably accommodated during the scheduled open... hearing session. The contact person will notify interested persons regarding their request to speak by...

  17. 78 FR 67365 - Circulatory System Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting

    Science.gov (United States)

    2013-11-12

    ... Washington DC North/Gaithersburg, Salons A, B, C, and D, 620 Perry Pkwy., Gaithersburg, MD 20877. The hotel's... notice in the Federal Register about last minute modifications that impact a previously announced... Technology. The WATCHMAN LAA Closure Technology is a percutaneously delivered permanent cardiac implant...

  18. Development of a mini-mobile digital radiography system by using wireless smart devices.

    Science.gov (United States)

    Jeong, Chang-Won; Joo, Su-Chong; Ryu, Jong-Hyun; Lee, Jinseok; Kim, Kyong-Woo; Yoon, Kwon-Ha

    2014-08-01

    The current technologies that trend in digital radiology (DR) are toward systems using portable smart mobile as patient-centered care. We aimed to develop a mini-mobile DR system by using smart devices for wireless connection into medical information systems. We developed a mini-mobile DR system consisting of an X-ray source and a Complementary Metal-Oxide Semiconductor (CMOS) sensor based on a flat panel detector for small-field diagnostics in patients. It is used instead of the systems that are difficult to perform with a fixed traditional device. We also designed a method for embedded systems in the development of portable DR systems. The external interface used the fast and stable IEEE 802.11n wireless protocol, and we adapted the device for connections with Picture Archiving and Communication System (PACS) and smart devices. The smart device could display images on an external monitor other than the monitor in the DR system. The communication modules, main control board, and external interface supporting smart devices were implemented. Further, a smart viewer based on the external interface was developed to display image files on various smart devices. In addition, the advantage of operators is to reduce radiation dose when using remote smart devices. It is integrated with smart devices that can provide X-ray imaging services anywhere. With this technology, it can permit image observation on a smart device from a remote location by connecting to the external interface. We evaluated the response time of the mini-mobile DR system to compare to mobile PACS. The experimental results show that our system outperforms conventional mobile PACS in this regard.

  19. Thermal energy storage devices, systems, and thermal energy storage device monitoring methods

    Science.gov (United States)

    Tugurlan, Maria; Tuffner, Francis K; Chassin, David P.

    2016-09-13

    Thermal energy storage devices, systems, and thermal energy storage device monitoring methods are described. According to one aspect, a thermal energy storage device includes a reservoir configured to hold a thermal energy storage medium, a temperature control system configured to adjust a temperature of the thermal energy storage medium, and a state observation system configured to provide information regarding an energy state of the thermal energy storage device at a plurality of different moments in time.

  20. Data processing device for computed tomography system

    International Nuclear Information System (INIS)

    Nakayama, N.; Ito, Y.; Iwata, K.; Nishihara, E.; Shibayama, S.

    1984-01-01

    A data processing device applied to a computed tomography system which examines a living body utilizing radiation of X-rays is disclosed. The X-rays which have penetrated the living body are converted into electric signals in a detecting section. The electric signals are acquired and converted from an analog form into a digital form in a data acquisition section, and then supplied to a matrix data-generating section included in the data processing device. By this matrix data-generating section are generated matrix data which correspond to a plurality of projection data. These matrix data are supplied to a partial sum-producing section. The partial sums respectively corresponding to groups of the matrix data are calculated in this partial sum-producing section and then supplied to an accumulation section. In this accumulation section, the final value corresponding to the total sum of the matrix data is calculated, whereby the calculation for image reconstruction is performed

  1. Energy harvesting devices, systems, and related methods

    Science.gov (United States)

    Kotter, Dale K.

    2016-10-18

    Energy harvesting devices include a substrate and a plurality of resonance elements coupled to the substrate. Each resonance element is configured to collect energy in the visible and infrared light spectra and to reradiate energy having a wavelength in the range of about 0.8 .mu.m to about 0.9 .mu.m. The resonance elements are arranged in groups of two or more resonance elements. Systems for harvesting electromagnetic radiation include a substrate, a plurality of resonance elements including a conductive material carried by the substrate, and a photovoltaic material coupled to the substrate and to at least one resonance element. The resonance elements are arranged in groups, such as in a dipole, a tripole, or a bowtie configuration. Methods for forming an energy harvesting device include forming groups of two or more discrete resonance elements in a substrate and coupling a photovoltaic material to the groups of discrete resonance elements.

  2. Electric drive systems including smoothing capacitor cooling devices and systems

    Energy Technology Data Exchange (ETDEWEB)

    Dede, Ercan Mehmet; Zhou, Feng

    2017-02-28

    An electric drive system includes a smoothing capacitor including at least one terminal, a bus bar electrically coupled to the at least one terminal, a thermoelectric device including a first side and a second side positioned opposite the first side, where the first side is thermally coupled to at least one of the at least one terminal and the bus bar, and a cooling element thermally coupled to the second side of the thermoelectric device, where the cooling element dissipates heat from the thermoelectric device.

  3. News and Events - Nanodelivery Systems and Devices Branch

    Science.gov (United States)

    The latest news from the Nanodelivery Systems and Devices Branch and the Alliance, as well as upcoming and past events attended by the Nanodelivery Systems and Devices Branchstaff, and relevant upcoming scientific meetings.

  4. Designing a concentrating photovoltaic (CPV) system in adjunct with a silicon photovoltaic panel for a solar competition car

    Science.gov (United States)

    Arias-Rosales, Andrés.; Barrera-Velásquez, Jorge; Osorio-Gómez, Gilberto; Mejía-Gutiérrez, Ricardo

    2014-06-01

    Solar competition cars are a very interesting research laboratory for the development of new technologies heading to their further implementation in either commercial passenger vehicles or related applications. Besides, worldwide competitions allow the spreading of such ideas where the best and experienced teams bet on innovation and leading edge technologies, in order to develop more efficient vehicles. In these vehicles, some aspects generally make the difference such as aerodynamics, shape, weight, wheels and the main solar panels. Therefore, seeking to innovate in a competitive advantage, the first Colombian solar vehicle "Primavera", competitor at the World Solar Challenge (WSC)-2013, has implemented the usage of a Concentrating Photovoltaic (CPV) system as a complementary solar energy module to the common silicon photovoltaic panel. By harvesting sunlight with concentrating optical devices, CPVs are capable of maximizing the allowable photovoltaic area. However, the entire CPV system weight must be less harmful than the benefit of the extra electric energy generated, which in adjunct with added manufacture and design complexity, has intervened in the fact that CPVs had never been implemented in a solar car in such a scale as the one described in this work. Design considerations, the system development process and implementation are presented in this document considering both the restrictions of the context and the interaction of the CPV system with the solar car setup. The measured data evidences the advantage of using this complementary system during the competition and the potential this technology has for further developments.

  5. Swimming type inspection device and system thereof

    International Nuclear Information System (INIS)

    Ito, Arata; Kimura, Motohiko; Ito, Tomoyuki

    1998-01-01

    The present invention provides a swimming type inspection device which can be reduced in the size, easily accessible to each portion of a reactor, and increase the degree of freedom of swimming and visual range, and facilitate visual inspection. The swimming type inspection device comprises two photographing devices, a device which can obtain propelling force by rotation of impellers, two second propelling devices having impellers disposed in perpendicular to the rotating axis of the impellers of the first propelling device, a control device for controlling control signals of first and second propelling devices and driving devices therefor and control image signals of the photographing devices, and transmission section for wireless transmitting of the control signals and the image signals. (N.H.)

  6. Performance of panel photovoltaic in an isolated system; Desempenho de painel fotovoltaico em um sistema isolado

    Energy Technology Data Exchange (ETDEWEB)

    Gnoatto, Estor [Centro Federal de Educacao Tecnologica do Parana (CEFET-PR), Mediadeira, PR (Brazil)], e-mail: estor@unioeste.br; Ferruzzi, Yuri; Munemuri Junior, Miguel [Universidade Estadual do Oeste do Parana (UNIOESTE), Cascavel, PR (Brazil)], e-mail: yuri@unioeste.br, e-mail: miguel@fag.edu.br; Ricieri, Reginaldo P. [Universidade Estadual do Oeste do Parana (UNIOESTE), Cascavel, PR (Brazil). Curso de Mestrado e Graduacao em Engenharia Agricola], e-mail: ricieri@unioeste.br; Oliveira, Adriana T.E. de [Universidade Estadual do Oeste do Parana (UNIOESTE), Cascavel, PR (Brazil)], e-mail: atoliveira@unioeste.br

    2004-07-01

    The installation of photovoltaic modules has if turned an alternative source of supply of electric energy, the present work had as objective to evaluate the efficiency of photovoltaic panels of multi crystalline silicon, through its installation in an isolated system, in conditions natural meteorological of the region, and having an automatic system of acquisition of data, for the tension indexes, current, and temperature, of the panel and the incident solar irradiation in the same inclination of the cells, during the year of 2002. (author)

  7. The response of wavelength shifting panels in large water Cherenkov systems

    International Nuclear Information System (INIS)

    Bakich, A.M.; Peak, L.S.

    1986-01-01

    This paper describes a series of tests performed with a panel Bicron wavelength shifting acrylic plastic (BC-480) coupled to an EMI 9623B photomultiplier tube. The aim was to effectively increase the cathode coverage and its sensitivity to incident Cherenkov radiation, so that such a system could be employed in a solar neutrino detector. Measurements of the uniformity and effective efficiency of the system have been made and compared with the results of various simulation runs. The effects of side mirrors, back reflector, water interface and possible shaping of the panel to enhance its response are also assessed. (orig.)

  8. Magnetic evaluation of a solar panel using HTS-SQUID

    International Nuclear Information System (INIS)

    Kiwa, Toshihiko; Fukudome, Yohei; Miyazaki, Shingo; Saari, Mohd Mawardi; Sakai, Kenji; Tsukada, Keiji

    2013-01-01

    Highlights: •The magnetic evaluation system of a solar panel using HTS-SQUID has been developed. •The electric circuits made by the discrete devices on the circuit board were visualized. •The electric properties of the commercial solar panels were demonstrated. -- Abstract: The magnetic evaluation system of a solar panel using HTS-SQUID has been proposed and developed. A normal pick-up coil was applied to detect the tangential magnetic field to the panel surface. Since the detected field could be related to the currents of the solar panels, the electric properties of the solar panels could be evaluated. In this work, the evaluation of the electric properties of the commercial solar panels as well as the electric circuits made by the discrete devices on the circuit board was visualized

  9. Method and system for mesh network embedded devices

    Science.gov (United States)

    Wang, Ray (Inventor)

    2009-01-01

    A method and system for managing mesh network devices. A mesh network device with integrated features creates an N-way mesh network with a full mesh network topology or a partial mesh network topology.

  10. [Design and application of implantable medical device information management system].

    Science.gov (United States)

    Cao, Shaoping; Yin, Chunguang; Zhao, Zhenying

    2013-03-01

    Through the establishment of implantable medical device information management system, with the aid of the regional joint sharing of resources, we further enhance the implantable medical device traceability management level, strengthen quality management, control of medical risk.

  11. Outer skin protection of columbium Thermal Protection System (TPS) panels

    Science.gov (United States)

    Culp, J. D.

    1973-01-01

    A coated columbium alloy material system 0.04 centimeter thick was developed which provides for increased reliability to the load bearing character of the system in the event of physical damage to and loss of the exterior protective coating. The increased reliability to the load bearing columbium alloy (FS-85) was achieved by interposing an oxidation resistant columbium alloy (B-1) between the FS-85 alloy and a fused slurry silicide coating. The B-1 alloy was applied as a cladding to the FS-85 and the composite was fused slurry silicide coated. Results of material evaluation testing included cyclic oxidation testing of specimens with intentional coating defects, tensile testing of several material combinations exposed to reentry profile conditions, and emittance testing after cycling of up to 100 simulated reentries. The clad material, which was shown to provide greater reliability than unclad materials, holds significant promise for use in the thermal protection system of hypersonic reentry vehicles.

  12. Application of a multi-gene next-generation sequencing panel to a non-invasive oesophageal cell-sampling device to diagnose dysplastic Barrett's oesophagus.

    Science.gov (United States)

    Katz-Summercorn, Annalise; Anand, Shubha; Ingledew, Sophie; Huang, Yuanxue; Roberts, Thomas; Galeano-Dalmau, Nuria; O'Donovan, Maria; Liu, Hongxiang; Fitzgerald, Rebecca C

    2017-10-01

    The early detection and endoscopic treatment of patients with the dysplastic stage of Barrett's oesophagus is a key to preventing progression to oesophageal adenocarcinoma. However, endoscopic surveillance protocols are hampered by the invasiveness of repeat endoscopy, sampling bias, and a subjective histopathological diagnosis of dysplasia. In this case-control study, we investigated the use of a non-invasive, pan-oesophageal cell-sampling device, the Cytosponge™, coupled with a cancer hot-spot panel to identify patients with dysplastic Barrett's oesophagus. Formalin-fixed, paraffin-embedded (FFPE) Cytosponge™ samples from 31 patients with non-dysplastic and 28 with dysplastic Barrett's oesophagus with good available clinical annotation were selected for inclusion. Samples were microdissected and amplicon sequencing performed using a panel covering > 2800 COSMIC hot-spot mutations in 50 oncogenes and tumour suppressor genes . S trict mutation criteria were determined and duplicates were run to confirm any mutations with an allele frequency panel achieved a 71.4% sensitivity (95% CI 51.3-86.8) and 90.3% (95% CI 74.3-98.0) specificity for diagnosing dysplasia. TP53 had the highest rate of mutation in 14/28 dysplastic samples (50%). CDKN2A was mutated in 6/28 (21.4%), ERBB2 in 3/28 (10.7%), and 5 other genes at lower frequency. The only gene from this panel found to be mutated in the non-dysplastic cases was CDKN2A in 3/31 cases (9.7%) in keeping with its known loss early in the natural history of the disease. Hence, it is possible to apply a multi-gene cancer hot-spot panel and next-generation sequencing to microdissected, FFPE samples collected by the Cytosponge™, in order to distinguish non-dysplastic from dysplastic Barrett's oesophagus. Further work is required to maximize the panel sensitivity.

  13. Data Base Management Systems Panel Workshop: Executive summary

    Science.gov (United States)

    1979-01-01

    Data base management systems (DBMS) for space acquired and associated data are discussed. The full range of DBMS needs is covered including acquiring, managing, storing, archiving, accessing and dissemination of data for an application. Existing bottlenecks in DBMS operations, expected developments in the field of remote sensing, communications, and computer science are discussed, and an overview of existing conditions and expected problems is presented. The requirements for a proposed spatial information system and characteristics of a comprehensive browse facility for earth observations applications are included.

  14. Use of perforated acoustic panels as supply air diffusers in diffuse ceiling ventilation systems

    DEFF Research Database (Denmark)

    Iqbal, Ahsan; Kazemi, Seyed Hossein; Ardkapan, Siamak Rahimi

    Ventilation is needed for diluting and removing the contaminants, odour and excess heat from the building interior. It is important that the inhabitants perceive the ventilated spaces as comfortable. Therefore, the supply air should reach all parts of the occupied zones. Troldtekt has been...... manufacturing perforated acoustic panels for the last 13 years. The panels can be used not only in applications related to acoustics but also as low pressure drop supply air diffusers, particularly in diffuse ceiling ventilation systems. The present study verifies on a theoretically level the performance...

  15. Hybrid system of unbonded post-tensioned CLT panels and light-frame wood shear walls

    Science.gov (United States)

    T. Ho; T. Dao; S. Aaleti; J. van de Lindt; Douglas Rammer

    2016-01-01

    Cross-laminated timber (CLT) is a relatively new type of massive timber system that has shown to possess excellent mechanical properties and structural behavior in building construction. When post-tensioned with high-strength tendons, CLT panels perform well under cyclic loadings because of two key characteristics: their rocking behavior and self-centering capacity....

  16. Study on the optimum tilted angle of solar panels in Hainan tropical photovoltaic facility agricultural system

    Science.gov (United States)

    Wang, Jingxuan; Ge, Zhiwu; Yang, Xiaoyan; Ye, Chunhua; Lin, Yanxia

    2017-04-01

    Photovoltaic facility agriculture system can effectively alleviate the contradiction between limited land and Photovoltaic power generation. It’s flexible to create suitable environment for crop growth, and generate electricity over the same land at the same time. It’s necessary to set appropriate solar panel angle to get more solar energy. Through detailed analysis and comparison, we chose the Hay’s model as solar radiation model. Based on the official meteorological data got from Haikou Meteorological Bureau, and by comparing the amount of radiation obtained at different tilted angles per month, the optimal placement angle of PV panels at different seasons in Haikou was obtained through calculation, and the optimal placement angle from April to October was also obtained. Through optimized angle and arrangement of solar photovoltaic panels, we can get greater power efficiency.

  17. Performance quantification of a flat-panel imager in industrial mega-voltage X-ray imaging systems

    International Nuclear Information System (INIS)

    Stritt, Carina; Plamondon, Mathieu; Hofmann, Jürgen; Flisch, Alexander; Sennhauser, Urs

    2017-01-01

    Active matrix flat-panel detectors have gained popularity amongst X-ray imaging systems due to their speed, resolution and high dynamic range. With appropriate shielding modern flat-panel imagers can even be used in high energy Computed Tomography (CT) systems of energies up to several mega-electronvolt (MeV). However, the performance of a digital detector is not independent of the rest of the radiographic system but depends on all other components of the system. Signal and noise transfer properties highly depend on all parameters of an imaging chain. This work focuses on quantifying the resolution capabilities and the noise in the signals of a MeV X-ray imaging system. The performance quantification is done by computing the modulation transfer function (MTF) using the standard edge method as well as the noise power spectrum (NPS) of the imaging system. We performed Monte Carlo (MC) simulations in order to understand the influence of scattered radiation on the measurements. A comparison of the horizontal and vertical MTF showed that the imaging behaviour of the detector is isotropic. Moreover, an additional investigation of the noise performance of the system showed that there is no measurable noise correlation present in the system. It was shown that the thickness of the edge device does not have a significant influence on the resulting system MTF. A rapid drop in the visibility could be observed resulting in a value of 1.2 line pairs per mm at 50% MTF. The visibility limit of line pair patterns was found to be at 2.3 line pairs per mm given by the 10% MTF value.

  18. Medical Devices; Ophthalmic Devices; Classification of the Diurnal Pattern Recorder System. Final order.

    Science.gov (United States)

    2016-05-31

    The Food and Drug Administration (FDA) is classifying the diurnal pattern recorder system into class II (special controls). The special controls that will apply to the device are identified in this order and will be part of the codified language for the diurnal pattern recorder system's classification. The Agency is classifying the device into class II (special controls) in order to provide a reasonable assurance of safety and effectiveness of the device.

  19. Medical Devices; General and Plastic Surgery Devices; Classification of the Magnetic Surgical Instrument System. Final order.

    Science.gov (United States)

    2016-09-21

    The Food and Drug Administration (FDA) is classifying the Magnetic Surgical Instrument System into class II (special controls). The special controls that will apply to the device are identified in this order and will be part of the codified language for the magnetic surgical instrument system's classification. The Agency is classifying the device into class II (special controls) in order to provide a reasonable assurance of safety and effectiveness of the device.

  20. Analysis of 3-panel and 4-panel microscale ionization sources

    International Nuclear Information System (INIS)

    Natarajan, Srividya; Parker, Charles B.; Glass, Jeffrey T.; Piascik, Jeffrey R.; Gilchrist, Kristin H.; Stoner, Brian R.

    2010-01-01

    Two designs of a microscale electron ionization (EI) source are analyzed herein: a 3-panel design and a 4-panel design. Devices were fabricated using microelectromechanical systems technology. Field emission from carbon nanotube provided the electrons for the EI source. Ion currents were measured for helium, nitrogen, and xenon at pressures ranging from 10 -4 to 0.1 Torr. A comparison of the performance of both designs is presented. The 4-panel microion source showed a 10x improvement in performance compared to the 3-panel device. An analysis of the various factors affecting the performance of the microion sources is also presented. SIMION, an electron and ion optics software, was coupled with experimental measurements to analyze the ion current results. The electron current contributing to ionization and the ion collection efficiency are believed to be the primary factors responsible for the higher efficiency of the 4-panel microion source. Other improvements in device design that could lead to higher ion source efficiency in the future are also discussed. These microscale ion sources are expected to find application as stand alone ion sources as well as in miniature mass spectrometers.

  1. 77 FR 69393 - Unique Device Identification System

    Science.gov (United States)

    2012-11-19

    ...'' instead of ``life- saving.'' FDA, the medical device industry, and the health care community are already... the efficient enforcement of the FD&C Act). Devices for which there has been a failure or refusal to... are misbranded under section 502(t)(2) of the FD&C Act (21 U.S.C. 352(t)(2)). The failure or refusal...

  2. Light-erasable embedded charge-trapping memory based on MoS2 for system-on-panel applications

    Science.gov (United States)

    He, Long-Fei; Zhu, Hao; Xu, Jing; Liu, Hao; Nie, Xin-Ran; Chen, Lin; Sun, Qing-Qing; Xia, Yang; Wei Zhang, David

    2017-11-01

    The continuous scaling and challenges in device integrations in modern portable electronic products have aroused many scientific interests, and a great deal of effort has been made in seeking solutions towards a more microminiaturized package assembled with smaller and more powerful components. In this study, an embedded light-erasable charge-trapping memory with a high-k dielectric stack (Al2O3/HfO2/Al2O3) and an atomically thin MoS2 channel has been fabricated and fully characterized. The memory exhibits a sufficient memory window, fast programming and erasing (P/E) speed, and high On/Off current ratio up to 107. Less than 25% memory window degradation is observed after projected 10-year retention, and the device functions perfectly after 8000 P/E operation cycles. Furthermore, the programmed device can be fully erased by incident light without electrical assistance. Such excellent memory performance originates from the intrinsic properties of two-dimensional (2D) MoS2 and the engineered back-gate dielectric stack. Our integration of 2D semiconductors in the infrastructure of light-erasable charge-trapping memory is very promising for future system-on-panel applications like storage of metadata and flexible imaging arrays.

  3. Testing and thermal modeling of radiant panels systems as commissioning tool

    International Nuclear Information System (INIS)

    Fonseca Diaz, Nestor; Cuevas, Cristian

    2010-01-01

    This paper presents the results of a study performed to develop a thermal modeling of radiant panels systems to be used in situ, as diagnosis tool in commissioning processes to determine the main operating conditions of the system in cooling or heating mode. The model considers the radiant panels as a finned heat exchanger in dry regime. By using as inputs the ceiling and room dimensions, the radiant ceiling material properties and the measurements of air and water mass flow rates and temperatures, the model is able to calculate the radiant ceiling capacity, ceiling surface average temperature, water exhaust temperature and resultant temperature as a comfort indicator. The modeling proposed considers combined convection, perforation effect and a detailed radiative heat exchange method for radiant ceiling systems. An example of each system considered in this study is shown, illustrating the validation of the model. A sensitive analysis of the model is performed.

  4. Performance comparison between silicon solar panel and dye-sensitized solar panel in Malaysia

    Science.gov (United States)

    Hamed, N. K. A.; Ahmad, M. K.; Urus, N. S. T.; Mohamad, F.; Nafarizal, N.; Ahmad, N.; Soon, C. F.; Ameruddin, A. S.; Faridah, A. B.; Shimomura, M.; Murakami, K.

    2017-09-01

    In carrying out experimental research in performance between silicon solar panel and dye-sensitive solar panel, we have been developing a device and a system. This system has been developed consisting of controllers, hardware and software. This system is capable to get most of the input sources. If only need to change the main circuit and coding for a different source input value. This device is able to get the ambient temperature, surface temperature, surrounding humidity, voltage with load, current with load, voltage without load and current without load and save the data into external memory. This device is able to withstand the heat and rain as it was fabricated in a waterproof box. This experiment was conducted to examine the performance of both the solar panels which are capable to maintain their stability and performance. A conclusion based on data populated, the distribution of data for dye-sensitized solar panel is much better than silicon solar panel as dye-sensitized solar panel is very sensitive to heat and not depend only on midday where is that is the maximum ambient temperature for both solar panel as silicon solar panel only can give maximum and high output only when midday.

  5. Medical Devices; Hematology and Pathology Devices; Classification of a Cervical Intraepithelial Neoplasia Test System. Final order.

    Science.gov (United States)

    2018-01-03

    The Food and Drug Administration (FDA or we) is classifying the cervical intraepithelial neoplasia (CIN) test system into class II (special controls). The special controls that apply to the device type are identified in this order and will be part of the codified language for the CIN test system's classification. We are taking this action because we have determined that classifying the device into class II (special controls) will provide a reasonable assurance of safety and effectiveness of the device. We believe this action will also enhance patients' access to beneficial innovative devices, in part by reducing regulatory burdens.

  6. MEDEMAS -Medical Device Management and Maintenance System Architecture

    Science.gov (United States)

    Dogan, Ülkü Balcı; Dogan, Mehmet Ugur; Ülgen, Yekta; Özkan, Mehmed

    In the proposed study, a medical device maintenance management system (MEDEMAS) is designed and implemented which provides a data pool of medical devices, the maintenance protocols and other required information for these devices. The system also contains complete repair and maintenance history of a specific device. MEDEMAS creates optimal maintenance schedule for devices and enables the service technician to carry out and report maintenance/repair processes via remote access. Thus predicted future failures are possible to prevent or minimize. Maintenance and repair is essential for patient safety and proper functioning of the medical devices, as it prevents performance decrease of the devices, deterioration of the equipment, and detrimental effects on the health of a patient, the user or other interacting people. The study aims to make the maintenance process more accurate, more efficient, faster and easier to manage and organize; and much less confusing. The accumulated history of medical devices and maintenance personnel helps efficient facility planning.

  7. Hydrogen production system from photovoltaic panels: experimental characterization and size optimization

    International Nuclear Information System (INIS)

    Ferrari, M.L.; Rivarolo, M.; Massardo, A.F.

    2016-01-01

    Highlights: • Plant optimization for hydrogen generation from renewable sources. • Experimental tests on a 42 kW alkaline electrolyser. • Time-dependent hierarchical thermo-economic optimization. • Italian case for electricity costs and solar irradiation (Savona). - Abstract: In this paper an approach for the determination of the optimal size and management of a plant for hydrogen production from renewable source (photovoltaic panels) is presented. Hydrogen is produced by a pressurized alkaline electrolyser (42 kW) installed at the University Campus of Savona (Italy) in 2014 and fed by electrical energy produced by photovoltaic panels. Experimental tests have been carried out in order to analyze the performance curve of the electrolyser in different operative conditions, investigating the influence of the different parameters on the efficiency. The results have been implemented in a software tool in order to describe the behavior of the systems in off-design conditions. Since the electrical energy produced by photovoltaic panels and used to feed the electrolyser is strongly variable because of the random nature of the solar irradiance, a time-dependent hierarchical thermo-economic analysis is carried out to evaluate both the optimal size and the management approach related to the system, considering a fixed size of 1 MW for the photovoltaic panels. The thermo-economic analysis is performed with the software tool W-ECoMP, developed by the authors’ research group: the Italian energy scenario is considered, investigating the impact of electricity cost on the results as well.

  8. Study of thermosiphon and radiant panel passive heating systems for metal buildings

    Energy Technology Data Exchange (ETDEWEB)

    Biehl, F.A.; Schnurr, N.M.; Wray, W.O.

    1983-01-01

    A study of passive-heating systems appropriate for use on metal buildings is being conducted at Los Alamos National Laboratory for the Naval Civil Engineering Laboratory, Port Hueneme, California. The systems selected for study were chosen on the basis of their appropriateness for retrofit applications, although they are also suitable for new construction: simple radiant panels that communicate directly with the building interior and a backflow thermosiphon that provides heat indirectly.

  9. Field evaluation of performance of radiant heating/cooling ceiling panel system

    DEFF Research Database (Denmark)

    Li, Rongling; Yoshidomi, Togo; Ooka, Ryozo

    2015-01-01

    As in many other countries in the world, Japan has witnessed an increased focus on low-energy buildings.For testing different engineering solutions for energy-efficient buildings, a low-energy building was builtat the University of Tokyo as an experimental pilot project. In this building, a radiant...... heating/coolingceiling panel system is used. However, no standard exists for the in situ performance evaluation of radiantheating/cooling ceiling systems; furthermore, no published database is available for comparison. Thus,this study aims to not only clarify the system performance but also to share our......, respectively. The upwardheat flux from the panels was found to be as large as 30–40% of the water heating/cooling capacity; thiswould translate into heat loss in certain operating modes. Several proposals for reducing the upwardheat flux were discussed. The measurements also showed that a category B thermal...

  10. Multi-axes sun-tracking system with PLC control for photovoltaic panels in Turkey

    Energy Technology Data Exchange (ETDEWEB)

    Sungur, Cemil [Selcuk University, Technical Science College, Electrical and Electronics Science, Alaeddin Keykubat Campus, 42075 Konya (Turkey)

    2009-04-15

    In the present study, the azimuth and solar altitude angles of the sun were calculated for a period of 1 year at 37.6 latitude in the Northern hemisphere, where Turkey is located, and according to these angles, an electromechanical system which tracks the sun on both axes and which is controlled via a programmable logic control (PLC) and an analog module was designed and implemented. After the mechanical control unit of the designed system was started, the performance measurements of the solar panel were carried out first when the solar panel was in a fixed position and then the solar panel was controlled while tracking the sun on azimuth and solar altitude angles and the necessary measurements were performed. It was observed that the control system operated without a problem. Besides, when the data obtained from the measurements were compared, it was seen that 42.6% more energy was obtained in the two-axes sun-tracking system when compared to the fixed system. (author)

  11. Electronic firing systems and methods for firing a device

    Science.gov (United States)

    Frickey, Steven J [Boise, ID; Svoboda, John M [Idaho Falls, ID

    2012-04-24

    An electronic firing system comprising a control system, a charging system, an electrical energy storage device, a shock tube firing circuit, a shock tube connector, a blasting cap firing circuit, and a blasting cap connector. The control system controls the charging system, which charges the electrical energy storage device. The control system also controls the shock tube firing circuit and the blasting cap firing circuit. When desired, the control system signals the shock tube firing circuit or blasting cap firing circuit to electrically connect the electrical energy storage device to the shock tube connector or the blasting cap connector respectively.

  12. 76 FR 51876 - Medical Devices; Ophthalmic Devices; Classification of the Eyelid Thermal Pulsation System

    Science.gov (United States)

    2011-08-19

    ... validate electromagnetic compatibility (EMC) and safety of exposure to non-ionizing radiation; (2) Design... HUMAN SERVICES Food and Drug Administration 21 CFR Part 886 Medical Devices; Ophthalmic Devices; Classification of the Eyelid Thermal Pulsation System AGENCY: Food and Drug Administration, HHS. ACTION: Final...

  13. Maintenance and Durability of the Concrete External Layer of Curtain Walls in Prefabricated Technological Poznan Large Panel System

    Science.gov (United States)

    Jasiczak, Józef; Girus, Krzysztof

    2017-10-01

    The issue of usability and durability of large-panel building constructed several decades ago is a subject of an in-depth analysis of many domestic and foreign investments. When considering the durability of specific large-panel system, one should consider, among others, the process of making external walls. The long-term and direct impact of weather conditions on the external layer of curtain walls is significant for the durability of large-panel buildings. For the needs of the presented paper, in 2016, the survey of cracks and a series of other tests of large-panel façade, residential building constructed in 1986, in Poland, in the PLP process system - Rataje was executed. Several hundred large-size, triple-layer curtain-wall slab with a 6-cm, concrete exterior cladding layer anchored using pins and hangers with the load-bearing layer, a 9-cm insulation layer made of mineral wool, and a 21-cm structural layer were surveyed. Significant deviations in thicknesses of particular wall layers were proven. Other significant damages and defects of external layers were found. At the second stage, many tests, both nondestructive and destructive, were conducted. They involved determining mechanical properties of an external layer. The concrete thickness was measured using with a type N Schmidt sclerometer and core samples were taken from this layer in order to mark concrete’s compressive strength. The range of carbonation (by phenolphthalein method) and the actual location and condition of reinforcement were estimated using a ferromagnetic device to determine the condition of the external layer. The diagnosis conducted in such a manner was the verification of necessary repair of the walls and their thermal efficiency improvement while ensuring safe conditions of their operation and modern functional and utility requirements. It should be also emphasized that the method of diagnosing the external walls presented in this paper may be popularized when evaluating such

  14. Hybrid harmonic compensation device adapted for variable speed drive system

    Science.gov (United States)

    Abramovich, B. N.; Sychev, Yu A.; Zimin, R. Yu

    2017-10-01

    The structure of the hybrid harmonic compensation device adapted for variable speed drive system is proposed in the paper. The main feature of the proposed device is the usage of common direct current link both for inverter of power frequency converter and for inverter of active part of the hybrid device. This decision allows to decrease the cost of active part of the proposed hybrid device. The proposed hybrid device is firstly intended for voltage and current harmonic determination and elimination. A mathematical model of generalized industrial power supply system with nonlinear load and the proposed hybrid device was developed by means of Matlab Simulink software. During simulation the proper efficiency of the proposed hybrid device is shown in different modes of voltage and current harmonic compensation.

  15. Integrated Thermal Treatment Systems study: US Department of Energy Internal Review Panel report

    Energy Technology Data Exchange (ETDEWEB)

    Cudahy, J.; Escarda, T.; Gimpel, R. [and others

    1995-04-01

    The U.S. Department of Energy`s (DOE) Office of Technology Development (OTD) commissioned two studies to uniformly evaluate nineteen thermal treatment technologies. These studies were called the Integrated Thermal Treatment System (ITTS) Phase I and Phase II. With the advice and guidance of the DOE Office of Environmental Management`s (EM`s) Mixed Waste Focus Group, OTD formed an ITTS Internal Review Panel, composed of scientists and engineers from throughout the DOE complex, the U.S. Environmental Protection Agency (EPA), the California EPA, and private experts. The Panel met from November 15-18, 1994, to review and comment on the ITTS studies, to make recommendations on the most promising thermal treatment systems for DOE mixed low level wastes (MLLW), and to make recommendations on research and development necessary to prove the performance of the technologies on MLLW.

  16. Low-cost modular array-field designs for flat-panel and concentrator photovoltaic systems

    Science.gov (United States)

    Post, H. N.; Carmichael, D. C.; Alexander, G.; Castle, J. A.

    1982-09-01

    Described are the design and development of low-cost, modular array fields for flat-panel and concentrator photovoltaic (PV) systems. The objective of the work was to reduce substantially the cost of the array-field Balance-of-System (BOS) subsystems and site-specific design costs as compared to previous PV installations. These subsystems include site preparation, foundations, support structures, electrical writing, grounding, lightning protection, electromagnetic interference considerations, and controls. To reduce these BOS and design costs, standardized modular (building-block) designs for flat-panel and concentrator array fields have been developed that are fully integrated and optimized for lowest life-cycle costs. Using drawings and specifications now available, these building-block designs can be used in multiples to install various size array fields. The developed designs are immediately applicable (1982) and reduce the array-field BOS costs to a fraction of previous costs.

  17. Integrated Thermal Treatment Systems study: US Department of Energy Internal Review Panel report

    International Nuclear Information System (INIS)

    Cudahy, J.; Escarda, T.; Gimpel, R.

    1995-04-01

    The U.S. Department of Energy's (DOE) Office of Technology Development (OTD) commissioned two studies to uniformly evaluate nineteen thermal treatment technologies. These studies were called the Integrated Thermal Treatment System (ITTS) Phase I and Phase II. With the advice and guidance of the DOE Office of Environmental Management's (EM's) Mixed Waste Focus Group, OTD formed an ITTS Internal Review Panel, composed of scientists and engineers from throughout the DOE complex, the U.S. Environmental Protection Agency (EPA), the California EPA, and private experts. The Panel met from November 15-18, 1994, to review and comment on the ITTS studies, to make recommendations on the most promising thermal treatment systems for DOE mixed low level wastes (MLLW), and to make recommendations on research and development necessary to prove the performance of the technologies on MLLW

  18. Device, method and system for preparing microcapsules

    DEFF Research Database (Denmark)

    2014-01-01

    into hydrophobic oil flow, which is horizontally maintained in the silicone tubing. The injection of polymer/cell mixture into a stream of mineral oil results in the generation of spherical droplet and in the formation of a water- in-oil emulsion due to the immiscibility of the two phases. Subsequently, the micro......The invention discloses a novel device for the formation of microcapsules based on micro-droplet generation inside silicone tubing, which is punctured with a blunt-ended syringe needle vertically (1). The device uses droplet generation by vertical injection of hydrophilic polymer/cell mixture......-droplets in oil phase are converted into stable microcapsules by gelation in a separate chamber which is loaded with ionic cross- linking solution at physiological ionic strength and pH. The utility of the microcapsules generated by the device of present invention is virtually unlimited in the fields...

  19. Detection and location of fouling on photovoltaic panels using a drone-mounted infrared thermography system

    Science.gov (United States)

    Zhang, Peng; Zhang, Lifu; Wu, Taixia; Zhang, Hongming; Sun, Xuejian

    2017-01-01

    Due to weathering and external forces, solar panels are subject to fouling and defects after a certain amount of time in service. These fouling and defects have direct adverse consequences such as low-power efficiency. Because solar power plants usually have large-scale photovoltaic (PV) panels, fast detection and location of fouling and defects across large PV areas are imperative. A drone-mounted infrared thermography system was designed and developed, and its ability to detect rapid fouling on large-scale PV panel systems was investigated. The infrared images were preprocessed using the K neighbor mean filter, and the single PV module on each image was recognized and extracted. Combining the local and global detection method, suspicious sites were located precisely. The results showed the flexible drone-mounted infrared thermography system to have a strong ability to detect the presence and determine the position of PV fouling. Drone-mounted infrared thermography also has good technical feasibility and practical value in the detection of PV fouling detection.

  20. Design of biomedical devices and systems

    CERN Document Server

    Press, CRC

    2014-01-01

    ""This book is a comprehensive overview of all the pieces that need to come together to bring a medical device from an idea to an approved device. It is an impressive compilation of information that is not easily found elsewhere, and included extensive references for every chapter. The writing is clear, yet succinct. The book is well organized with labeled subsections that let the reader find exactly what content he/she may want to explore. Each chapter has exercises that can be used as a self-assessment or to supplement a class.""-Anna Iwaniec Hickerson, Keck Graduate Institute of Appl

  1. Safety of mechanical devices. Safety of automation systems

    International Nuclear Information System (INIS)

    Pahl, G.; Schweizer, G.; Kapp, K.

    1985-01-01

    The paper deals with the classic procedures of safety engineering in the sectors mechanical engineering, electrical and energy engineering, construction and transport, medicine technology and process technology. Particular stress is laid on the safety of automation systems, control technology, protection of mechanical devices, reactor safety, mechanical constructions, transport systems, railway signalling devices, road traffic and protection at work in chemical plans. (DG) [de

  2. Integrated neuron circuit for implementing neuromorphic system with synaptic device

    Science.gov (United States)

    Lee, Jeong-Jun; Park, Jungjin; Kwon, Min-Woo; Hwang, Sungmin; Kim, Hyungjin; Park, Byung-Gook

    2018-02-01

    In this paper, we propose and fabricate Integrate & Fire neuron circuit for implementing neuromorphic system. Overall operation of the circuit is verified by measuring discrete devices and the output characteristics of the circuit. Since the neuron circuit shows asymmetric output characteristic that can drive synaptic device with Spike-Timing-Dependent-Plasticity (STDP) characteristic, the autonomous weight update process is also verified by connecting the synaptic device and the neuron circuit. The timing difference of the pre-neuron and the post-neuron induce autonomous weight change of the synaptic device. Unlike 2-terminal devices, which is frequently used to implement neuromorphic system, proposed scheme of the system enables autonomous weight update and simple configuration by using 4-terminal synapse device and appropriate neuron circuit. Weight update process in the multi-layer neuron-synapse connection ensures implementation of the hardware-based artificial intelligence, based on Spiking-Neural- Network (SNN).

  3. Enabling Dynamic Security Management of Networked Systems via Device-Embedded Security (Self-Securing Devices)

    National Research Council Canada - National Science Library

    Ganger, Gregory R

    2007-01-01

    This report summarizes the results of the work on the AFOSR's Critical Infrastructure Protection Program project, entitled Enabling Dynamic Security Management of Networked Systems via Device-Embedded Security...

  4. Design of digital systems and devices

    CERN Document Server

    Adamski, Marian; Wegrzyn, Marek

    2011-01-01

    This book includes a variety of design and test methods targeted on different digital devices, as well as different logic elements. The authors of the book represent such countries as Israel, Poland, Russia, and Ukraine. The book is divided by three main parts, including thirteen different Chapters.

  5. 78 FR 58785 - Unique Device Identification System

    Science.gov (United States)

    2013-09-24

    ... Benefits Accounting Statement [2012 dollars] Units Category Primary estimate Low High Discount estimate...(g) AA. Requirements for Stand-Alone Software--Final Sec. 801.50 BB. Request for an Exception from or... software regulated as a stand[dash]alone software medical device. Proposed Sec. regulated as a medical...

  6. Design of Control System Device for Electron Gun Power Supply of 350 keV/10 mA Electron Beam Machine

    International Nuclear Information System (INIS)

    Eko Priyono; Budi Santosa; Taxwim

    2003-01-01

    The electron gun power supply control system of electron beam machine has been designed. Using this design regulator device for the electron gun power supply will be constructed. This regulator device was designed that it can be operated manually or automatically. Beside that, this was also provided with the safety system which is useful to scram the MBE when something wrong happened. The main components of the device are remote data communication system using infra red and fiber optic module, DC motor driver system, regulated transformer coupled by DC motor and operation panel system. (author)

  7. Lateral Load-Resisting System Using Mass Timber Panel for High-Rise Buildings

    Directory of Open Access Journals (Sweden)

    Zhiyong Chen

    2017-07-01

    Full Text Available As global interest in using engineered wood products in tall buildings intensifies due to the “green” credential of wood, it is expected that more tall wood buildings will be designed and constructed in the coming years. This, however, brings new challenges to the designers. One of the major challenges is how to design lateral load-resisting systems (LLRSs with sufficient stiffness, strength, and ductility to resist strong wind and earthquakes. In this study, an LLRS using mass timber panel on a stiff podium was developed for high-rise buildings in accordance with capacity-based design principle. The LLRS comprises eight shear walls with a core in the center of the building, which was constructed with structural composite lumber and connected with dowel-type connections and wood–steel composite system. The main energy dissipating mechanism of the LLRS was detailed to be located at the panel-to-panel interface. This LLRS was implemented in the design of a hypothetical 20-storey building. A finite element (FE model of the building was developed using general-purpose FE software, ABAQUS. The wind-induced and seismic response of the building model was investigated by performing linear static and non-linear dynamic analyses. The analysis results showed that the proposed LLRS using mass timber was suitable for high-rise buildings. This study provided a valuable insight into the structural performance of LLRS constructed with mass timber panels as a viable option to steel and concrete for high-rise buildings.

  8. Peer review panel summary report for technical determination of mixed waste incineration off-gas systems for Rocky Flats

    International Nuclear Information System (INIS)

    1992-01-01

    A Peer Review Panel was convened on September 15-17, 1992 in Boulder, Co. The members of this panel included representatives from DOE, EPA, and DOE contractors along with invited experts in the fields of air pollution control and waste incineration. The primary purpose of this review panel was to make a technical determination of a hold, test and release off gas capture system should be implemented in the proposed RF Pland mixed waste incineration system; or if a state of the art continuous air pollution control and monitoring system should be utilized as the sole off-gas control system. All of the evaluations by the panel were based upon the use of the fluidized bed unit proposed by Rocky Flats and cannot be generalized to other systems

  9. Magnesium-based methods, systems, and devices

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Yufeng; Ban, Chunmei; Ruddy, Daniel; Parilla, Philip A.; Son, Seoung-Bum

    2017-12-12

    An aspect of the present invention is an electrical device, where the device includes a current collector and a porous active layer electrically connected to the current collector to form an electrode. The porous active layer includes MgB.sub.x particles, where x.gtoreq.1, mixed with a conductive additive and a binder additive to form empty interstitial spaces between the MgB.sub.x particles, the conductive additive, and the binder additive. The MgB.sub.x particles include a plurality of boron sheets of boron atoms covalently bound together, with a plurality of magnesium atoms reversibly intercalated between the boron sheets and ionically bound to the boron atoms.

  10. Novel Devices and Components for THz Systems

    Science.gov (United States)

    2014-04-25

    low-temperature-grown (with molecular beam epitaxy) Gallium Arsenide (LT-GaAs). LT-GaAs was first utilized in photoconductive devices in the early...The cage rods themselves were mounted to this lens holder with the set screws. 66 87 The tunable mirror was made of the 6061 aluminum alloy...comprise the polarizer was also negligible because cheap metals could be used, such as aluminum . Additionally, the amount of metal used per polarizer is

  11. Design of biomedical devices and systems

    CERN Document Server

    King, Paul H

    2008-01-01

    Introduction to Biomedical Engineering Design. Fundamental Design Tools. Design Team Management, Reporting, and Documentation. Product Definition. Product Documentation. Product Development. Hardware Development Methods and Tools. Software Development Methods and Tools. Human Factors. Industrial Design. Biomaterials and Material Testing. Safety Engineering: Devices and Processes. Testing. Analysis of Test Data. Reliability and Liability. Food and Drug Administration. Regulations and Standards. Licensing, Patents, Copyrights, and Trade Secrets. Manufacturing and Quality Control. Miscellaneous Issues. Product Issues. Professional Issues. Design Case Studies. Future Design Issues.

  12. Building materials and systems with vacuum insulation panels for external walls; Bauelemente und Systeme mit VIP fuer Aussenwandkonstruktionen - Schlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Binz, A.; Steinke, G.

    2007-07-01

    This final report for the Swiss Federal Office of Energy (SFOE) takes a look at materials and systems using vacuum insulation panels (VIP) for the construction of external walls. The aim of this research project was the development, practical use and market introduction of VIP systems that take account of the special properties of VIP. Along with partners in industry, applications involving external and internal insulation were examined. The need for protecting the vacuum panels against mechanical damage is stressed. The specific needs for the protection of external and internal applications are discussed. The dynamic developments in this relatively new area are commented on. Various mounting systems are examined and commented on. The thermal properties of such insulation systems and applications are noted and commented on.

  13. Micro-inverter solar panel mounting

    Science.gov (United States)

    Morris, John; Gilchrist, Phillip Charles

    2016-02-02

    Processes, systems, devices, and articles of manufacture are provided. Each may include adapting micro-inverters initially configured for frame-mounting to mounting on a frameless solar panel. This securement may include using an adaptive clamp or several adaptive clamps secured to a micro-inverter or its components, and using compressive forces applied directly to the solar panel to secure the adaptive clamp and the components to the solar panel. The clamps can also include compressive spacers and safeties for managing the compressive forces exerted on the solar panels. Friction zones may also be used for managing slipping between the clamp and the solar panel during or after installation. Adjustments to the clamps may be carried out through various means and by changing the physical size of the clamps themselves.

  14. Metabolomics and its integration with systems biology: PSI 2014 conference panel discussion report.

    Science.gov (United States)

    More, Tushar; RoyChoudhury, Sourav; Gollapalli, Kishore; Patel, Sandip K; Gowda, Harsha; Chaudhury, Koel; Rapole, Srikanth

    2015-09-08

    Metabolomics, being a relatively new field, is facing multiple challenges related to data acquisition and interpretation, reproducibility across analytical platforms, integration with other omics approaches and translation into theragnostic biomarkers. There is an immediate need to overcome these challenges in order to make metabolomics more useful and reliable in terms of improving our current understanding of disease biology and help in developing predictive biomarkers. Researchers interested in metabolomics gathered for a panel discussion on 'Metabolomics and its integration with systems biology' during the 6th Annual Meeting of Proteomics Society-India and International Conference on "Proteomics from Discovery to Function" held at the Indian Institute of Technology, Bombay from December 7-9, 2014. The panel discussed various challenges related to metabolomics and also proposed several effective solutions for optimum implementation of metabolomics in clinical practice. The key areas of panel discussion were improvement in metabolite databases with comprehensive spectral libraries, need for extensive bioinformatics tools for integrative approaches and serious considerations for clinical validation of the biomarkers for the successful implementation of metabolomics in clinics. Information drafted in this report is significant for researchers working in metabolomics field to overcome the challenges and successful implementation of metabolomics in clinical practice. This article is part of a special issue titled: Proteomics in India. Copyright © 2015 Elsevier B.V. All rights reserved.

  15. Assessing the Structural, Driver and Economic Impacts of Traffic Pole Mounted Wind Power Generator and Solar Panel Hybrid System

    Science.gov (United States)

    2012-06-01

    This project evaluates the physical and economic feasibility of using existing traffic infrastructure to mount wind power : generators. Some possible places to mount a light weight wind generator and solar panel hybrid system are: i) Traffic : signal...

  16. Correlation Of An E-Nose System For Odor Assessment Of Shoe/Sock Systems With A Human Sensory Panel

    International Nuclear Information System (INIS)

    Horras, Stephan; Reimann, Peter; Schuetze, Andreas; Gaiotto, Alessandra; Mayer, Maria

    2009-01-01

    Evaluation of strength and quality of smell is today still primarily done with human sensory panels. For a range of applications, technical systems for an objective smell assessment would provide a great benefit in R and D and also day-to-day application. The project presented here specifically addresses the problem of assessing the strength and unpleasantness of smell caused by sweat in shoes and socks by an E-nose system. The ultimate goal is to provide a tool for developing improved shoe/sock systems with optimized materials.The main approach to achieve this goal is to find a correlation between the assessment of a human sensory panel and the complex sensor response patterns of an E-Nose system to appraise the smell of sweat in shoes and socks. Therefore a range of test persons wear shoes and socks under defined ambient conditions in a controlled test environment as well as during everyday use. Afterwards the smell of the shoes and socks is both measured with the E-Nose system and assessed by a human sensory panel. We report here the results of the first larger test series and the identified correlation between the E-Nose system and the human assessment of the smell of sweat.

  17. Application of energy storage devices in power systems | Gupta ...

    African Journals Online (AJOL)

    Some of the major disadvantages in electric power supply system have been flickering and deviations in power supply which make some of the electronic equipments and domestic devices highly sensitive to it. To avoid such problems we need to find out devices that can provide a backup during the time of voltage sags ...

  18. A parameters acquisition and device monitoring system for HIRFL

    International Nuclear Information System (INIS)

    Yao Nan; Huang Xinmin; Chen Yun; Zheng Jianhua; Huang Tuanhua; Tang Jingyu

    2002-01-01

    A practical application for patrolling the devices' status of HIRFL has been developed ad hoc in VC ++ environment. It periodically acquires the devices' parameters by running a server program on the corresponding consoles. A client program simultaneously reads these data via local network and displays the status of the current devices under control of the HIRFL distributed control system, and automatically gives alarm signals whenever exception occurs. It can respond the user's interruption requirement while running. Many practical functions, such as inclusion and exclusion of the listed devices, modification of their error range and automatic saving of the record of the exceptions and the relevant operations, are enabled

  19. A parameters acquisition and device monitoring system for HIRFL

    CERN Document Server

    Yao Nan; Chen Yun; Zheng Jian; Huang Tuan Hua; Tang Jin Gyu

    2002-01-01

    A practical application for patrolling the devices' status of HIRFL has been developed ad hoc in VC sup + sup + environment. It periodically acquires the devices' parameters by running a server program on the corresponding consoles. A client program simultaneously reads these data via local network and displays the status of the current devices under control of the HIRFL distributed control system, and automatically gives alarm signals whenever exception occurs. It can respond the user's interruption requirement while running. Many practical functions, such as inclusion and exclusion of the listed devices, modification of their error range and automatic saving of the record of the exceptions and the relevant operations, are enabled

  20. Power supply devices and systems of relay protection

    CERN Document Server

    Gurevich, Vladimir

    2013-01-01

    Power Supply Devices and Systems of Relay Protection brings relay protection and electrical power engineers a single, concentrated source of information on auxiliary power supply systems and devices. The book also tackles specific problems and solutions of relay protection power supply systems and devices, which are often not dealt with in the literature. The author, an experienced engineer with more than 100 patents, draws on his own experience to offer practical, tested advice to readers. A Guide to Relay Protection Power Supply for Engineers and Technicians The first chapter reviews the ele

  1. Development of a DAQ system for a plasma display panel-based X-ray detector (PXD)

    International Nuclear Information System (INIS)

    Lee, Hakjae; Jung, Young-Jun; Eom, Sangheum; Kang, Jungwon; Lee, Kisung

    2015-01-01

    Recently, a novel plasma display panel (PDP)-based X-ray detector (PXD) was developed. The goal of this study is to develop a data acquisition system for use with the PXD as an imaging detector. Since the prototype detector does not have any barrier ribs or a switching device in a detector pixel, a novel pixelation scheme—the line-scan method—is developed for this new detector. To implement line scanning, a multichannel high-voltage switching circuit and a multichannel charge-acquisition circuit are developed. These two circuits are controlled by an FPGA-based digital signal processing board, from which the information about the charge and position of each pixel can be sent to a PC. FPGA-based baseline compensation and switching noise rejection algorithms are used to improve the signal-to-noise ratio (SNR). The characteristic curve of the entire PXD system is acquired, and the correlation coefficients between the X-ray dose, and the signal intensity and the SNR were determined to be approximately 0.99 and 52.9, respectively. - Highlights: • We developed a data acquisition circuit for a novel X-ray imaging detector. • Line scan, noise rejection, and data transmission methods have been implemented by the FPGA. • The linearity and SNR of the proposed detector system have been measured quantitatively

  2. Impact of the Implementation of Photovoltaic Panels at Cayo Santa Maria Electric System

    International Nuclear Information System (INIS)

    Gallego Landera, Yandi Aníbal; Casas Fernandez, Leonardo; Garcia Sanchez, Zaid; Rivas Arocha, Yanet

    2017-01-01

    The global interest in encouraging the use of renewable energy has triggered a massive opening unconventional generation units. In view of the current incentives at country level for the installation of photovoltaic panels (PFV), it is possible to foresee that in the future there will be high penetration of distributed generation of this type connected to the electrical system. In our province, Cayo Santa Maria isolated system has three areas for the installation of PFV. As stated above and considering that high penetration levels of photovoltaic generation produces static and dynamic effects in connected isolated systems, it is essential to conduct studies systemically to determine the impact that would produce this connection, taking into consideration its location, technology, modeling and penetration level. The analysis allows to know how beneficial or harmful the installation of photovoltaic generators can be in that system. (author)

  3. Development of a cloud-based system for remote monitoring of a PVT panel

    Science.gov (United States)

    Saraiva, Luis; Alcaso, Adérito; Vieira, Paulo; Ramos, Carlos Figueiredo; Cardoso, Antonio Marques

    2016-10-01

    The paper presents a monitoring system developed for an energy conversion system based on the sun and known as thermophotovoltaic panel (PVT). The project was implemented using two embedded microcontrollers platforms (arduino Leonardo and arduino yún), wireless transmission systems (WI-FI and XBEE) and net computing ,commonly known as cloud (Google cloud). The main objective of the project is to provide remote access and real-time data monitoring (like: electrical current, electrical voltage, input fluid temperature, output fluid temperature, backward fluid temperature, up PV glass temperature, down PV glass temperature, ambient temperature, solar radiation, wind speed, wind direction and fluid mass flow). This project demonstrates the feasibility of using inexpensive microcontroller's platforms and free internet service in theWeb, to support the remote study of renewable energy systems, eliminating the acquisition of dedicated systems typically more expensive and limited in the kind of processing proposed.

  4. An asynchronous, pipelined, electronic acquisition system for Active Matrix Flat-Panel Imagers (AMFPIs)

    CERN Document Server

    Huang, W; Berry, J; Maolinbay, M; Martelli, C; Mody, P; Nassif, S; Yeakey, M

    1999-01-01

    The development of a full-custom electronic acquisition system designed for readout of large-area active matrix flat-panel imaging arrays is reported. The arrays, which comprise two-dimensional matrices of pixels utilizing amorphous silicon thin-film transistors, are themselves under development for a wide variety of X-ray imaging applications. The acquisition system was specifically designed to facilitate detailed, quantitative investigations of the properties of these novel imaging arrays and contains significant enhancements compared to a previously developed acquisition system. These enhancements include pipelined preamplifier circuits to allow faster readout speed, expanded addressing capabilities allowing a maximum of 4096 array data lines, and on-board summing of image frames. The values of many acquisition system parameters, including timings and voltages, may be specified and downloaded from a host computer. Once acquisition is enabled, the system operates asynchronously of its host computer. The sys...

  5. System Control Applications of Low-Power Radio Frequency Devices

    Science.gov (United States)

    van Rensburg, Roger

    2017-09-01

    This paper conceptualizes a low-power wireless sensor network design for application employment to reduce theft of portable computer devices used in educational institutions today. The aim of this study is to design and develop a reliable and robust wireless network that can eradicate accessibility of a device’s human interface. An embedded system supplied by an energy harvesting source, installed on the portable computer device, may represent one of multiple slave nodes which request regular updates from a standalone master station. A portable computer device which is operated in an undesignated area or in a field perimeter where master to slave communication is restricted, indicating a possible theft scenario, will initiate a shutdown of its operating system and render the device unusable. Consequently, an algorithm in the device firmware may ensure the necessary steps are executed to track the device, irrespective whether the device is enabled. Design outcomes thus far indicate that a wireless network using low-power embedded hardware, is feasible for anti-theft applications. By incorporating one of the latest Bluetooth low-energy, ANT+, ZigBee or Thread wireless technologies, an anti-theft system may be implemented that has the potential to reduce major portable computer device theft in institutions of digitized learning.

  6. Signal Processing Device (SPD) for networked radiation monitoring system

    International Nuclear Information System (INIS)

    Dharmapurikar, A.; Bhattacharya, S.; Mukhopadhyay, P.K.; Sawhney, A.; Patil, R.K.

    2010-01-01

    A networked radiation and parameter monitoring system with three tier architecture is being developed. Signal Processing Device (SPD) is a second level sub-system node in the network. SPD is an embedded system which has multiple input channels and output communication interfaces. It acquires and processes data from first level parametric sensor devices, and sends to third level devices in response to request commands received from host. It also performs scheduled diagnostic operations and passes on the information to host. It supports inputs in the form of differential digital signals and analog voltage signals. SPD communicates with higher level devices over RS232/RS422/USB channels. The system has been designed with main requirements of minimal power consumption and harsh environment in radioactive plants. This paper discusses the hardware and software design details of SPD. (author)

  7. Remotely Piloted Aircraft Systems Panel (RPASP) Working Paper: Autonomy and Automation

    Science.gov (United States)

    Shively, Jay

    2017-01-01

    A significant level of debate and confusion has surrounded the meaning of the terms "autonomy" and "automation". Automation is a multi-dimensional concept, and we propose that RPAS automation should be described with reference to the specific system and task that has been automated, the context in which the automation functions, and other relevant dimensions. In this paper, we present a definition of "automation". We recommend that autonomy and autonomous operations are out of the scope of the RPAS panel. WG7 proposes to develop, in consultation with other workgroups, a taxonomy of "Levels of Automation" for RPAS.

  8. Nanomedical device and systems design challenges, possibilities, visions

    CERN Document Server

    2014-01-01

    Nanomedical Device and Systems Design: Challenges, Possibilities, Visions serves as a preliminary guide toward the inspiration of specific investigative pathways that may lead to meaningful discourse and significant advances in nanomedicine/nanotechnology. This volume considers the potential of future innovations that will involve nanomedical devices and systems. It endeavors to explore remarkable possibilities spanning medical diagnostics, therapeutics, and other advancements that may be enabled within this discipline. In particular, this book investigates just how nanomedical diagnostic and

  9. Danish translation and validation of the International Skin Tear Advisory Panel Skin Tear Classification System

    DEFF Research Database (Denmark)

    Skiveren, J; Bermark, S; LeBlanc, K

    2015-01-01

    ) and social and health-care assistants (non-RN) from both primary health care and a Danish university hospital in Copenhagen. Thirty photographs, with equal representation of the three types of skin tears, were selected to test validity. The photographs chosen were those originally used for internal.......443, respectively). CONCLUSION: The ISTAP Skin Tear Classification System was developed with the goal of establishing a global language for describing and documenting skin tears and to raise the health-care community's awareness of skin tears. The Danish translation of the ISTAP classification system supports......OBJECTIVE: The aim of this study was to translate, validate and establish reliability of the International Skin Tear Classification System in Danish. METHOD: Phase 1 of the project involved the translation of the International Skin Tear Advisory Panel (ISTAP) Skin Tear Classification System...

  10. Performance Characteristic of a CsI(Tl) Flat Panel Detector Radiography System

    International Nuclear Information System (INIS)

    Jeong, Hoi Woun; Min, Jung Hwan; Kim, Jung Min; Park, Min Seok; Lee, Gaung Young

    2012-01-01

    The purpose of this work was to evaluate an amorphous silicon cesium iodide based indirect flat-panel detector (FPD) in terms of their modulation transfer function (MTF), Wiener spectrum (WS, or noise power spectrum, NPS), and detective quantum efficiency (DQE). Measurements were made on flat-panel detector using the International Electrotechnical Commission (IEC) defined RQA3, RQA5, RQA7, and RQA9 radiographic technique. The MTFs of the systems were measured using an edge method. The WS(NPS) of the systems were determined for a range of exposure levels by two-dimensional (2D). Fourier analysis of uniformly exposed radiographs. The DQEs were assessed from the measured MTF, WS(NPS), exposure, and estimated ideal signal-to-noise ratios. Characteristic curve in the RQA3 showed difference in the characteristic curve from RQA5, RQA7, RQA9. MTFs were not differences according to x-ray beam quality. WS(NPS) was reduced with increasing dose, and RQA 3, RQA5, RQA7, RQA9 as the order is reduced. DQE represented the best in the 1mR, RQA 3, RQA5, RQA7, RQA9 decrease in the order. The physical imaging characteristics of FPD may also differ from input beam quality. This study gives an initial motivation that the physical imaging characteristics of FPD is an important issue for the right use of digital radiography system.

  11. Performance Characteristic of a CsI(Tl) Flat Panel Detector Radiography System

    Energy Technology Data Exchange (ETDEWEB)

    Jeong, Hoi Woun [Dept. of Radiological Science, Baekseok Culture University, Seoul (Korea, Republic of); Min, Jung Hwan [Dept. of Radiological Technology, Shingu University, Seongnam (Korea, Republic of); Kim, Jung Min [Dept. of Radiological Science, Korea University, Health Science College, Seoul (Korea, Republic of); Park, Min Seok [Korea Institue of Radiological and Medical Sicences, Research Institute of Radiologycal and Medical Sciences, Seoul (Korea, Republic of); Lee, Gaung Young [National Institute of Food and Drug Safety Evaluation, Seoul (Korea, Republic of)

    2012-06-15

    The purpose of this work was to evaluate an amorphous silicon cesium iodide based indirect flat-panel detector (FPD) in terms of their modulation transfer function (MTF), Wiener spectrum (WS, or noise power spectrum, NPS), and detective quantum efficiency (DQE). Measurements were made on flat-panel detector using the International Electrotechnical Commission (IEC) defined RQA3, RQA5, RQA7, and RQA9 radiographic technique. The MTFs of the systems were measured using an edge method. The WS(NPS) of the systems were determined for a range of exposure levels by two-dimensional (2D). Fourier analysis of uniformly exposed radiographs. The DQEs were assessed from the measured MTF, WS(NPS), exposure, and estimated ideal signal-to-noise ratios. Characteristic curve in the RQA3 showed difference in the characteristic curve from RQA5, RQA7, RQA9. MTFs were not differences according to x-ray beam quality. WS(NPS) was reduced with increasing dose, and RQA 3, RQA5, RQA7, RQA9 as the order is reduced. DQE represented the best in the 1mR, RQA 3, RQA5, RQA7, RQA9 decrease in the order. The physical imaging characteristics of FPD may also differ from input beam quality. This study gives an initial motivation that the physical imaging characteristics of FPD is an important issue for the right use of digital radiography system.

  12. Development of a DAQ system for a plasma display panel-based X-ray detector (PXD)

    Science.gov (United States)

    Lee, Hakjae; Jung, Young-Jun; Eom, Sangheum; Kang, Jungwon; Lee, Kisung

    2015-06-01

    Recently, a novel plasma display panel (PDP)-based X-ray detector (PXD) was developed. The goal of this study is to develop a data acquisition system for use with the PXD as an imaging detector. Since the prototype detector does not have any barrier ribs or a switching device in a detector pixel, a novel pixelation scheme-the line-scan method-is developed for this new detector. To implement line scanning, a multichannel high-voltage switching circuit and a multichannel charge-acquisition circuit are developed. These two circuits are controlled by an FPGA-based digital signal processing board, from which the information about the charge and position of each pixel can be sent to a PC. FPGA-based baseline compensation and switching noise rejection algorithms are used to improve the signal-to-noise ratio (SNR). The characteristic curve of the entire PXD system is acquired, and the correlation coefficients between the X-ray dose, and the signal intensity and the SNR were determined to be approximately 0.99 and 52.9, respectively.

  13. Prototyping of concurrent control systems implemented in FPGA devices

    CERN Document Server

    Wiśniewski, Remigiusz

    2017-01-01

    This book focuses on prototyping aspects of concurrent control systems and their further implementation and partial reconfiguration in programmable devices. Further, it lays out a full prototyping flow for concurrent control systems. Based on a given primary specification, a system is described with an interpreted Petri net, which naturally reflects the concurrent and sequential relationships of the design. The book shows that, apart from the traditional option of static configuration of the entire system, the latest programmable devices (especially FPGAs) offer far more sophistication. Partial reconfiguration allows selected parts of the system to be replaced without having to reprogram the entire structure of the device. Approaches to dynamic and static partial reconfiguration of concurrent control systems are presented and described in detail.< The theoretical work is illustrated by examples drawn from various applications, with a milling machine and a traffic-light controller highlighted as representat...

  14. Developing Control System of Electrical Devices with Operational Expense Prediction

    Science.gov (United States)

    Sendari, Siti; Wahyu Herwanto, Heru; Rahmawati, Yuni; Mukti Putranto, Dendi; Fitri, Shofiana

    2017-04-01

    The purpose of this research is to develop a system that can monitor and record home electrical device’s electricity usage. This system has an ability to control electrical devices in distance and predict the operational expense. The system was developed using micro-controllers and WiFi modules connected to PC server. The communication between modules is arranged by server via WiFi. Beside of reading home electrical devices electricity usage, the unique point of the proposed-system is the ability of micro-controllers to send electricity data to server for recording the usage of electrical devices. The testing of this research was done by Black-box method to test the functionality of system. Testing system run well with 0% error.

  15. Constancy tests radiography X-ray devices with CR system

    International Nuclear Information System (INIS)

    Durdikova, M.; Zakova, M.

    2005-01-01

    The paper presents the changes in QAP (Quality Assurance Program) as consequence of digitalisation of medical facilities. Digitalisation brings many advantages - more comfort for personal use, images are easy achievable and transferable to workstation, fine quality images by postprocessing are easily achievable. But it must be taken into account that due to simplicity of image make it is sometimes taken more images then necessary .There are two possible ways of digitalisation in radiography: to exchange conventional developer machine by Computer Radiography (CR), that means to use CR reader and cassette with phosphor plate - un-direct digitalisation or to use special radiography X-ray devices with flat-panel detector -direct radiography. (authors)

  16. Electrical overstress (EOS) devices, circuits and systems

    CERN Document Server

    Voldman, Steven H

    2013-01-01

    Electrical Overstress (EOS) continues to impact semiconductor manufacturing, semiconductor components and systems as technologies scale from micro- to nano-electronics.  This bookteaches the fundamentals of electrical overstress  and how to minimize and mitigate EOS failures. The text provides a clear picture of EOS phenomena, EOS origins, EOS sources, EOS physics, EOS failure mechanisms, and EOS on-chip and system design.  It provides an illuminating insight into the sources of EOS in manufacturing, integration of on-chip, and system level EOS protection networks, followed by examples in spe

  17. Memristive Systems Analysis of 3-Terminal Devices

    OpenAIRE

    Mouttet, Blaise

    2010-01-01

    Memristive systems were proposed in 1976 by Leon Chua and Sung Mo Kang as a model for 2-terminal passive nonlinear dynamical systems which exhibit memory effects. Such systems were originally shown to be relevant to the modeling of action potentials in neurons in regards to the Hodgkin-Huxley model and, more recently, to the modeling of thin film materials such as TiO2-x proposed for non-volatile resistive memory. However, over the past 50 years a variety of 3-terminal non-passive dynamical d...

  18. Metabolic Panel

    Science.gov (United States)

    A metabolic panel is a group of tests that measures different chemicals in the blood. These tests are usually done on ... and liver. There are two types: basic metabolic panel (BMP) and comprehensive metabolic panel (CMP). The BMP ...

  19. Critical incidence reporting systems - an option in equine anaesthesia? Results from a panel meeting.

    Science.gov (United States)

    Hartnack, Sonja; Bettschart-Wolfensberger, Regula; Driessen, Bernd; Pang, Daniel; Wohlfender, Franziska

    2013-11-01

    To provide a brief introduction into Critical Incident Reporting Systems (CIRS) as used in human medicine, and to report the discussion from a recent panel meeting discussion with 23 equine anaesthetists in preparation for a new CEPEF-4 (Confidential Enquiry into Perioperative Equine Fatalities) study. Moderated group discussions, and review of literature. The first group discussion focused on the definition of 'preventable critical incidents' and/or 'near misses' in the context of equine anaesthesia. The second group discussion focused on categorizing critical incidents according to an established framework for analysing risk and safety in clinical medicine. While critical incidents do occur in equine anaesthesia, no critical incident reporting system including systematic collection and analysis of critical incidents is in place. Critical incident reporting systems could be used to improve safety in equine anaesthesia - in addition to other study types such as mortality studies. © 2013 Association of Veterinary Anaesthetists and the American College of Veterinary Anesthesia and Analgesia.

  20. Structural performance of new thin-walled concrete sandwich panel system reinforced with bfrp shear connectors

    DEFF Research Database (Denmark)

    Hodicky, Kamil; Hulin, Thomas; Schmidt, Jacob Wittrup

    2013-01-01

    This paper presents a new thin-walled concrete sandwich panel system reinforced with basalt fiber-reinforced plastic (BFRP) with optimum structural performances and a high thermal resistance developed by Connovate and Technical University of Denmark. The shear connecting system made of a BFRP grid...... is described and provides information on the structural design with its advantages. Experimental and numerical investigations of the BFRP connecting systems were performed. The experimental program included testing of small scale specimens by applying shear (push-off) loading and semi-full scale specimens...... by flexural loading. Numerical investigations were based on 3-D linear elastic finite element analysis. Results from the numerical investigations were compared with experimental results of small and semi-scale specimens for the validation of the design procedure. Experimental and numerical results based...

  1. Reliability and safety analysis for systems of fusion device

    Energy Technology Data Exchange (ETDEWEB)

    Alzbutas, Robertas, E-mail: robertas.alzbutas@lei.lt; Voronov, Roman

    2015-05-15

    Highlights: • Reliability is very important from fusion devices efficiency perspective. • Rich experience of probabilistic safety analysis exists in nuclear industry. • Reliability and safety analysis was applied for systems of fusion device. • This enables to identify and prioritize availability improvement measures. • Recommendations are based on cost effectiveness for risk decrease options. - Abstract: Fusion energy or thermonuclear power is a promising, literally endless source of energy. Development of fusion power is still under investigation and experimental phase, and a number of fusion devices are under construction in Europe. Since fusion energy is innovative and fusion devices contain unique and expensive equipment, an issue of their reliability is very important from their efficiency perspective. A Reliability, Availability, Maintainability, Inspectability (RAMI) analysis is being performed or is going to be performed in the nearest future for such fusion devices as ITER and DEMO in order to ensure reliable and efficient operation for experiments (e.g., in ITER) or for energy production purposes (e.g., in DEMO). On the other hand, rich experience of the reliability and Probabilistic Safety Analysis (PSA) exists in nuclear industry for fission power plants and other nuclear installations. In this paper, the Wendelstein 7-X (W7-X) device is mainly considered. This stellarator device is in commissioning stage in the Max-Planck-Institut für Plasmaphysik, Greifswald, Germany (IPP). In the frame of cooperation between the IPP and the Lithuanian Energy Institute (LEI) under the European Fusion Development Agreement a pilot project of a reliability analysis of the W7-X systems was performed with a purpose to adopt Nuclear Power Plant (NPP) PSA experience for fusion device systems. During the project reliability and safety (risk) analysis of a Divertor Target Cooling Circuit, which is an important system for permanent and reliable operation of in

  2. Video integrated measurement system. [Diagnostic display devices

    Energy Technology Data Exchange (ETDEWEB)

    Spector, B.; Eilbert, L.; Finando, S.; Fukuda, F.

    1982-06-01

    A Video Integrated Measurement (VIM) System is described which incorporates the use of various noninvasive diagnostic procedures (moire contourography, electromyography, posturometry, infrared thermography, etc.), used individually or in combination, for the evaluation of neuromusculoskeletal and other disorders and their management with biofeedback and other therapeutic procedures. The system provides for measuring individual diagnostic and therapeutic modes, or multiple modes by split screen superimposition, of real time (actual) images of the patient and idealized (ideal-normal) models on a video monitor, along with analog and digital data, graphics, color, and other transduced symbolic information. It is concluded that this system provides an innovative and efficient method by which the therapist and patient can interact in biofeedback training/learning processes and holds considerable promise for more effective measurement and treatment of a wide variety of physical and behavioral disorders.

  3. Development of filter systems injection systems and mixing device evaluation

    International Nuclear Information System (INIS)

    Loughborough, D.

    1989-01-01

    A problem when in-situ testing High Efficiency Particulate Air (HEPA) filters is to ensure that the test aerosol provides a uniform challenge to the whole of the filter face. Uniform challenge is defined in this case as a concentration variation of aerosol across the plane of the duct of less than +/- 10%. Injecting into an open duct via a single point injector requires a minimum of 30 hydraulic duct diameters (De) between the injector and sample point to ensure a mixed flow. This may be reduced to 10De with the use of a Stairmand disc mixer. Methods of reducing the lengths of ducting required for an in-situ filter test have been investigated. Results shows that there is a minimum aerosol exit velocity below which the mixing length requirement may be substantially increased. By ensuring that this minimum velocity is exceeded, Harwell has developed a system of multiple point injectors in conjunction with a modified Stairmand disc which reduces the mixing length to 5.5De. Further work has investigated two plane devices which reduce the lengths of ducting to 4.0De, although these have an associated increased resistance to airflow

  4. Novel Na(+) doped Alq3 hybrid materials for organic light-emitting diode (OLED) devices and flat panel displays.

    Science.gov (United States)

    Bhagat, S A; Borghate, S V; Kalyani, N Thejo; Dhoble, S J

    2015-05-01

    Pure and Na(+) -doped Alq3 complexes were synthesized by a simple precipitation method at room temperature, maintaining a stoichiometric ratio. These complexes were characterized by X-ray diffraction, Fourier transform infrared (FTIR), UV/Vis absorption and photoluminescence (PL) spectra. The X-ray diffractogram exhibits well-resolved peaks, revealing the crystalline nature of the synthesized complexes, FTIR confirms the molecular structure and the completion of quinoline ring formation in the metal complex. UV/Vis absorption and PL spectra of sodium-doped Alq3 complexes exhibit high emission intensity in comparison with Alq3 phosphor, proving that when doped in Alq3 , Na(+) enhances PL emission intensity. The excitation spectra of the synthesized complexes lie in the range 242-457 nm when weak shoulders are also considered. Because the sharp excitation peak falls in the blue region of visible radiation, the complexes can be employed for blue chip excitation. The emission wavelength of all the synthesized complexes lies in the bluish green/green region ranging between 485 and 531 nm. The intensity of the emission wavelength was found to be elevated when Na(+) is doped into Alq3 . Because both the excitation and emission wavelengths fall in the visible region of electromagnetic radiation, these phosphors can also be employed to improve the power conversion efficiency of photovoltaic cells by using the solar spectral conversion principle. Thus, the synthesized phosphors can be used as bluish green/green light-emitting phosphors for organic light-emitting diodes, flat panel displays, solid-state lighting technology - a step towards the desire to reduce energy consumption and generate pollution free light. Copyright © 2014 John Wiley & Sons, Ltd.

  5. Overload protection device for pulsed electric systems

    International Nuclear Information System (INIS)

    Glushchenko, V.G.; Kurskov, I.A.; Semina, R.S.

    1976-01-01

    Results of pulsed electric system protection development from effective pulse current overload depending on pulse duration are described. An integrating circuit, charge resistance of which is connected in parallel with a stabilitron, is used in a protection diagram. Given were time responses of overload protection of an output lens of slow root particle extraction channel from synchrophasotron; the responses have been obtained by the experimental and calculation methods

  6. Semiconductor terahertz technology devices and systems at room temperature operation

    CERN Document Server

    Carpintero, G; Hartnagel, H; Preu, S; Raisanen, A

    2015-01-01

    Key advances in Semiconductor Terahertz (THz) Technology now promises important new applications enabling scientists and engineers to overcome the challenges of accessing the so-called "terahertz gap".  This pioneering reference explains the fundamental methods and surveys innovative techniques in the generation, detection and processing of THz waves with solid-state devices, as well as illustrating their potential applications in security and telecommunications, among other fields. With contributions from leading experts, Semiconductor Terahertz Technology: Devices and Systems at Room Tempe

  7. THERMOELECTRIC DEVICES TO PROVIDE THERMAL BLOCK MODE ELECTRONIC SYSTEMS

    Directory of Open Access Journals (Sweden)

    T. A. Ismailov

    2015-01-01

    Full Text Available The article deals with thermoelectric cooling (TEC device to provide thermal mode power electronics systems cluster design, are areas of constructive solutions use the feasibility study of the device, a description of the experimental facility and methodology of the experiment, the dependences of temperature on the simulator of the electronic board from the exhaust of the feasibility study power, temperatures of hot and cold junctions, the speed of the air flow and the distance between the electronic boards. 

  8. Automatic coordination of protection devices in distribution system

    International Nuclear Information System (INIS)

    Comassetto, L.; Bernardon, D.P.; Canha, L.N.; Abaide, A.R.

    2008-01-01

    Among the several components of distribution systems, protection devices present a fundamental importance, since they aim at keeping the physical integrity not only of the system equipment, but also of the electricians' team and the population in general. The existing tools today in the market that carry out the making of protection studies basically draw curves, and need direct user's interference for the protection devices adjustment and coordination analyses of selectivity, being susceptible to the user's mistakes and not always considering the best technical and economical application. In Brazil, the correct application of the protection devices demand a high amount of time, being extremely laborious due to the great number of devices (around 200 devices), besides the very dynamic behaviour of distribution networks and the need for constant system expansion. This article presents a computational tool developed with the objective of automatically determining the adjustments of all protection devices in the distribution networks to obtain the best technical application, optimizing its performance and making easier protection studies. (author)

  9. Humid free efficient solar panel

    Science.gov (United States)

    Panjwani, Manoj Kumar; Panjwani, Suresh Kumar; Mangi, Fareed Hussain; Khan, Danish; Meicheng, Li

    2017-09-01

    The paper examines the impact of the humidity on the Solar panels which makes a space for the drastic variation in the power generated and makes the device less efficient. Humidity readily affects the efficiency of the solar cells and creates a minimal layer of water on its surface. It also decreases the efficiency by 10-20% of the total power output produced. Moreover, to handle this issue, all around characterized measures are required to be taken to guarantee the smooth working of the solar panels utilized in humid areas. In connection with this issue, Karachi, the biggest city of Pakistan which is located near the costal line touching Arabian Sea, was taken as a reference city to measure the humidity range. In Karachi, the average humidity lies between 25-70% (as per Pakistan Meteorological Department PMD), that indirectly leads in decreasing power acquired from a Solar Panel and develops various complexities for the solar system. The system on average experiences stability issues, such as those of power fluctuations etc., due to which, the whole solar system installed observes abnormal variations in acquired power. Silica Gel was used as a desiccant material in order to assure dryness over the solar panel. More than four experiments were conducted with the usage of water absorbent to improve the efficiency and to make system more power efficient.

  10. Microcomputer based test system for charge coupled devices

    International Nuclear Information System (INIS)

    Sidman, S.

    1981-02-01

    A microcomputer based system for testing analog charge coupled integrated circuits has been developed. It measures device performance for three parameters: dynamic range, baseline shift due to leakage current, and transfer efficiency. A companion board tester has also been developed. The software consists of a collection of BASIC and assembly language routines developed on the test system microcomputer

  11. Quantum communications system with integrated photonic devices

    Energy Technology Data Exchange (ETDEWEB)

    Nordholt, Jane E.; Peterson, Charles Glen; Newell, Raymond Thorson; Hughes, Richard John

    2017-11-14

    Security is increased in quantum communication (QC) systems lacking a true single-photon laser source by encoding a transmitted optical signal with two or more decoy-states. A variable attenuator or amplitude modulator randomly imposes average photon values onto the optical signal based on data input and the predetermined decoy-states. By measuring and comparing photon distributions for a received QC signal, a single-photon transmittance is estimated. Fiber birefringence is compensated by applying polarization modulation. A transmitter can be configured to transmit in conjugate polarization bases whose states of polarization (SOPs) can be represented as equidistant points on a great circle on the Poincare sphere so that the received SOPs are mapped to equidistant points on a great circle and routed to corresponding detectors. Transmitters are implemented in quantum communication cards and can be assembled from micro-optical components, or transmitter components can be fabricated as part of a monolithic or hybrid chip-scale circuit.

  12. Tracking Systems for Orientation of Solar Panels and Optimization of their Positioning Using Three-coordinate Platforms

    Directory of Open Access Journals (Sweden)

    Chalbash O.H.

    2017-12-01

    Full Text Available Two-coordinate platforms equipped with orientation systems are 40-45% more effective than stationary installations. However, there are other factors affecting the efficiency of solar installations. In particular, the shading on the panels’ surfaces when panels, located in rows, are casting shadows on each other. This negatively affects the efficiency of photovoltaic installations. Previous experience in the design of photovoltaic systems shows that neither stationary platforms nor two-coordinate installations completely eliminate energy losses due to shadow formation. The only way to mitigate this negative impact is to increase the distance between the panels. At the same time, and the density ratio (the ratio of the panel area to the area of the land does not exceed 0.2. Our goal is to develop kinematic schemes and software control systems for three coordinate platforms that can avoid shadow formation on panels placed in constrained spaces. The result of our work is a numerical method that solves the optimization problem for controlling the motion of a set of platforms and a rational kinematic scheme for three coordinate platforms. This problem is especially relevant for solar photovoltaic systems located on space stations. In space, the changes in temperature between shaded and shadow-free sections of panels is enormous, due to temperature stress, the panels get destroyed and require expensive repairs. Three-coordinate tracking can reduce the surface occupied by solar panels by about 3 times compared to the currently used solutions and increased module placement densities from 0.2 to 0.6.

  13. Terrestrial radiation effects in ULSI devices and electronic systems

    CERN Document Server

    Ibe, Eishi H

    2014-01-01

    A practical guide on how mathematical approaches can be used to analyze and control radiation effects in semiconductor devices within various environments Covers faults in ULSI devices to failures in electronic systems caused by a wide variety of radiation fields, including electrons, alpha -rays, muons, gamma rays, neutrons and heavy ions. Readers will learn the environmental radiation features at the ground or avionics altitude. Readers will also learn how to make numerical models from physical insight and what kind of mathematical approaches should be implemented to analyze the radiation effects. A wide variety of mitigation techniques against soft-errors are reviewed and discussed. The author shows how to model sophisticated radiation effects in condensed matter in order to quantify and control them. The book provides the reader with the knowledge on a wide variety of radiation fields and their effects on the electronic devices and systems. It explains how electronic systems including servers and rout...

  14. Interagency Nuclear Safety Review Panel Power System Subpanel review for the Ulysses mission

    International Nuclear Information System (INIS)

    McCulloch, W.H.

    1991-01-01

    As part of the Interagency Nuclear Safety Review Panel's assessment of the nuclear safety of NASA's Ulysses Mission to investigate properties of the sun, the Power System Subpanel has reviewed the safety analyses and risk evaluations done for the General Purpose Heat Source-Radioisotope Thermoelectric Generator which provides on-board electrical power for the spacecraft. This paper summarizes the activities and results of that review. In general, the approach taken in the primary analysis, executed by the General Electric Company under contract to the Department of Energy, and the resulting conclusions were confirmed by the review. However, the Subpanel took some exceptions and modified the calculations accordingly, producing an independent evaluation of potential releases of radioactive fuel in launch and reentry accidents. Some of the more important of these exceptions are described briefly

  15. ADC's Insertion Devices and Magnetic Measurement Systems Capabilities

    Science.gov (United States)

    Deyhim, A.; Kulesza, J.

    2013-03-01

    In this paper Advance Design Consulting USA, Inc. (ADC) will discuss ADC's major improved capabilities for building Wiggler Insertion Devices, Undulator Planar Devices, Elliptical Polarizing Undulators (EPU), In-Vacuum Undulators (IVU), Cryogenically Cooled in-vacuum Undulators (CPMU), Super Conductive Undulator, and Insertion Device Magnetic Measurement Systems. ADC has designed, built and delivered Insertion Devices and Magnetic Measurement Systems to such facilities as MAX-lab (two EPUs, a Planar, and Measurement System), ALBA and ASP (Wigglers), BNL (CPMU), SSRF (two IVUs and a Measurement System), PAL (one IVU and Measurement System), NSRRC (one 4m EPU), and SRC (Planar and EPU). ADC's magnetic field measurement system is a sophisticated and sensitive machine for the measurement of magnetic fields in undulators (Planar and EPU), wigglers and in-vacuum ID units. The magnetic fields are measured using 3 axis hall-effect probes, mounted orthogonally, to a thin wand. The wand is mounted to a carriage that rides on vacuum air bearings. The base is granite. A flip coil is provided on two vertical towers with X, Y and Theta axes. Special software is provided to assist in homing, movement, and data collection and analysis.

  16. Design, Simulation and Experimental Investigation of a Solar System Based on PV Panels and PVT Collectors

    Directory of Open Access Journals (Sweden)

    Annamaria Buonomano

    2016-06-01

    Full Text Available This paper presents numerical and experimental analyses aimed at evaluating the technical and economic feasibility of photovoltaic/thermal (PVT collectors. An experimental setup was purposely designed and constructed in order to compare the electrical performance of a PVT solar field with the one achieved by an identical solar field consisting of conventional photovoltaic (PV panels. The experimental analysis also aims at evaluating the potential advantages of PVT vs. PV in terms of enhancement of electrical efficiency and thermal energy production. The installed experimental set-up includes four flat polycrystalline silicon PV panels and four flat unglazed polycrystalline silicon PVT collectors. The total electrical power and area of the solar field are 2 kWe and 13 m2, respectively. The experimental set-up is currently installed at the company AV Project Ltd., located in Avellino (Italy. This study also analyzes the system from a numerical point of view, including a thermo-economic dynamic simulation model for the design and the assessment of energy performance and economic profitability of the solar systems consisting of glazed PVT and PV collectors. The experimental setup was modelled and partly simulated in TRNSYS environment. The simulation model was useful to analyze efficiencies and temperatures reached by such solar technologies, by taking into account the reference technology of PVTs (consisting of glazed collectors as well as to compare the numerical data obtained by dynamic simulations with the gathered experimental results for the PV technology. The numerical analysis shows that the PVT global efficiency is about 26%. Conversely, from the experimental point of view, the average thermal efficiency of PVT collectors is around 13% and the electrical efficiencies of both technologies are almost coincident and equal to 15%.

  17. A Novel Binocular Vision System for Wearable Devices.

    Science.gov (United States)

    Zhai, Haitian; Li, Hui; Bai, Yicheng; Jia, Wenyan; Sun, Mingui

    2014-04-25

    We present a novel binocular imaging system for wearable devices incorporating the biology knowledge of the human eyes. Unlike the camera system in smartphones, two fish-eye lenses with a larger angle of view are used, the visual field of the new system is larger, and the central resolution of output images is higher. This design leads to more effective image acquisition, facilitating computer vision tasks such as target recognition, navigation and object tracking.

  18. Comparison of solar panel cooling system by using dc brushless fan and dc water

    International Nuclear Information System (INIS)

    Irwan, Y M; Leow, W Z; Irwanto, M; M, Fareq; Hassan, S I S; Amelia, A R; Safwati, I

    2015-01-01

    The purpose of this article is to discuss comparison of solar panel cooling system by using DC brushless fan and DC water pump. Solar photovoltaic (PV) power generation is an interesting technique to reduce non-renewable energy consumption and as a renewable energy. The temperature of PV modules increases when it absorbs solar radiation, causing a decrease in efficiency. A solar cooling system is design, construct and experimentally researched within this work. To make an effort to cool the PV module, Direct Current (DC) brushless fan and DC water pump with inlet/outlet manifold are designed for constant air movement and water flow circulation at the back side and front side of PV module representatively. Temperature sensors were installed on the PV module to detect temperature of PV. PIC microcontroller was used to control the DC brushless fan and water pump for switch ON or OFF depend on the temperature of PV module automatically. The performance with and without cooling system are shown in this experiment. The PV module with DC water pump cooling system increase 3.52%, 36.27%, 38.98%in term of output voltage, output current, output power respectively. It decrease 6.36 °C compare than to PV module without DC water pump cooling system. While DC brushless fan cooling system increase 3.47%, 29.55%, 32.23%in term of output voltage, output current, and output power respectively. It decrease 6.1 °C compare than to PV module without DC brushless fan cooling system. The efficiency of PV module with cooling system was increasing compared to PV module without cooling system; this is because the ambient temperature dropped significantly. The higher efficiency of PV cell, the payback period of the system can be shorted and the lifespan of PV module can also be longer. (paper)

  19. Comparison of solar panel cooling system by using dc brushless fan and dc water

    Science.gov (United States)

    Irwan, Y. M.; Leow, W. Z.; Irwanto, M.; M, Fareq; Hassan, S. I. S.; Safwati, I.; Amelia, A. R.

    2015-06-01

    The purpose of this article is to discuss comparison of solar panel cooling system by using DC brushless fan and DC water pump. Solar photovoltaic (PV) power generation is an interesting technique to reduce non-renewable energy consumption and as a renewable energy. The temperature of PV modules increases when it absorbs solar radiation, causing a decrease in efficiency. A solar cooling system is design, construct and experimentally researched within this work. To make an effort to cool the PV module, Direct Current (DC) brushless fan and DC water pump with inlet/outlet manifold are designed for constant air movement and water flow circulation at the back side and front side of PV module representatively. Temperature sensors were installed on the PV module to detect temperature of PV. PIC microcontroller was used to control the DC brushless fan and water pump for switch ON or OFF depend on the temperature of PV module automatically. The performance with and without cooling system are shown in this experiment. The PV module with DC water pump cooling system increase 3.52%, 36.27%, 38.98%in term of output voltage, output current, output power respectively. It decrease 6.36 °C compare than to PV module without DC water pump cooling system. While DC brushless fan cooling system increase 3.47%, 29.55%, 32.23%in term of output voltage, output current, and output power respectively. It decrease 6.1 °C compare than to PV module without DC brushless fan cooling system. The efficiency of PV module with cooling system was increasing compared to PV module without cooling system; this is because the ambient temperature dropped significantly. The higher efficiency of PV cell, the payback period of the system can be shorted and the lifespan of PV module can also be longer.

  20. AN ANALYSIS OF THE CHARACTERISTICS OF PUBLIC HEALTH SYSTEM AT REGIONAL LEVEL USING PANEL DATA

    Directory of Open Access Journals (Sweden)

    CATALINA LILIANA ANDREI

    2011-04-01

    Full Text Available Reforming the public health system is a complex and long process, involving different categories of people. To accelerate the process of integration into the European Union, Romania is currently implementing strategies and programs aimed to increase the quality of public services. In the medical field a series of measures have been undertaken aimed at accelerating the decentralization process and optimize the activities of medical institutions. During the transition period a series of measures have been taken to decentralization and privatization of health services. However, currently we are witnessing a fragmentation of the system, which stressed the inequality in the distribution of medical personnel and reduced people's access to certain types of medical services. Please note that the number of doctors per capita in rural areas is only 20% of the urban area. Another major shortcoming of the system is linked to the financing system and its correlation with the strategies of decentralization. Frequently, decentralization has emerged as a way of placing the central tasks in the task of local government. Using panel data from developing regions we highlight a number of implications of the decentralization process.

  1. An implantable thermoresponsive drug delivery system based on Peltier device.

    Science.gov (United States)

    Yang, Rongbing; Gorelov, Alexander V; Aldabbagh, Fawaz; Carroll, William M; Rochev, Yury

    2013-04-15

    Locally dropping the temperature in vivo is the main obstacle to the clinical use of a thermoresponsive drug delivery system. In this paper, a Peltier electronic element is incorporated with a thermoresponsive thin film based drug delivery system to form a new drug delivery device which can regulate the release of rhodamine B in a water environment at 37 °C. Various current signals are used to control the temperature of the cold side of the Peltier device and the volume of water on top of the Peltier device affects the change in temperature. The pulsatile on-demand release profile of the model drug is obtained by turning the current signal on and off. The work has shown that the 2600 mAh power source is enough to power this device for 1.3 h. Furthermore, the excessive heat will not cause thermal damage in the body as it will be dissipated by the thermoregulation of the human body. Therefore, this simple novel device can be implanted and should work well in vivo. Copyright © 2013 Elsevier B.V. All rights reserved.

  2. On the feasibility of device fingerprinting in industrial control systems

    NARCIS (Netherlands)

    Caselli, M.; Hadziosmanovic, D.; Zambon, Emmanuele; Kargl, Frank; Luiijf, Eric; Hartel, Pieter H.

    2013-01-01

    As Industrial Control Systems (ICS) and standard IT networks are becoming one heterogeneous entity, there has been an increasing effort in adjusting common security tools and methodologies to fit the industrial environment. Fingerprinting of industrial devices is still an unexplored research field.

  3. Ceramics and healthy heating and cooling systems: thermal ceramic panels in buildings. Conditions of comfort and energy demand versus convective systems

    Directory of Open Access Journals (Sweden)

    V. Echarri Iribarren

    2016-12-01

    Full Text Available Porcelain stoneware is a widely used building material. In recent years, its range of uses has expanded to encompass a new spectrum of innovative and inventive applications in architecture. In this research, we analysed the patented Thermal Ceramic Panel. This consists of a thin porcelain stoneware panel that incorporates a capillary system of polypropylene tubes measuring 3.5 mm in diameter embedded in a conductive ceramic interface. The system works with hot or cold water, producing healthy heating and cooling by means of radiant surfaces. Following an initial prototype test in which panels were placed on the walls of an office, we conducted simulations at the University of Alicante Museum using wall, ceiling and baffle panels, having previously monitored the state of the building. Thermal behaviour parameters were analysed and compared with those of other standard finishing materials, obtaining results for thermal comfort and energy savings in comparison with all-air systems.

  4. Respiratory protective device design using control system techniques

    Science.gov (United States)

    Burgess, W. A.; Yankovich, D.

    1972-01-01

    The feasibility of a control system analysis approach to provide a design base for respiratory protective devices is considered. A system design approach requires that all functions and components of the system be mathematically identified in a model of the RPD. The mathematical notations describe the operation of the components as closely as possible. The individual component mathematical descriptions are then combined to describe the complete RPD. Finally, analysis of the mathematical notation by control system theory is used to derive compensating component values that force the system to operate in a stable and predictable manner.

  5. 242-A Control System device logic software documentation. Revision 2

    International Nuclear Information System (INIS)

    Berger, J.F.

    1995-01-01

    A Distributive Process Control system was purchased by Project B-534. This computer-based control system, called the Monitor and Control System (MCS), was installed in the 242-A Evaporator located in the 200 East Area. The purpose of the MCS is to monitor and control the Evaporator and Monitor a number of alarms and other signals from various Tank Farm facilities. Applications software for the MCS was developed by the Waste Treatment System Engineering Group of Westinghouse. This document describes the Device Logic for this system

  6. Devices, systems, and methods for harvesting energy and methods for forming such devices

    Science.gov (United States)

    Kotter, Dale K.; Novack, Steven D.

    2012-12-25

    Energy harvesting devices include a substrate coupled with a photovoltaic material and a plurality of resonance elements associated with the substrate. The resonance elements are configured to collect energy in at least visible and infrared light spectra. Each resonance element is capacitively coupled with the photovoltaic material, and may be configured to resonate at a bandgap energy of the photovoltaic material. Systems include a photovoltaic material coupled with a feedpoint of a resonance element. Methods for harvesting energy include exposing a resonance element having a resonant electromagnetic radiation having a frequency between approximately 20 THz and approximately 1,000 THz, absorbing at least a portion of the electromagnetic radiation with the resonance element, and resonating the resonance element at a bandgap energy of an underlying photovoltaic material. Methods for forming an energy harvesting device include forming resonance elements on a substrate and capacitively coupling the resonance elements with a photovoltaic material.

  7. Use of digital computing devices in systems important to safety

    International Nuclear Information System (INIS)

    1986-01-01

    The incorporation of digital computing devices in systems important to safety now is progressing fast in several countries, including Canada, France, Federal Republic of Germany, Japan, USA. There are now reactors with microprocessors in some trip systems. The major functions of those systems are: reactor trip initiation, display, monitoring, testing, re-calibration of detectors. The benefits of moving to a fully computerized shut-down system should be improved reliability, greater flexibility, better man-machine interface, improved testing, higher reactor output and lower overall cost. With the introduction of computer devices in systems important to safety, plant availability and safety are improved because disturbances are treated before they lead to safety action, in this way helping the operator to avoid errors. The Meeting presentations were divided into sessions devoted to the following topics: Needs for the use of digital devices (DCD) in safety important systems (SIS) (5 papers); Problems raised by the integration SIS in the NPP control (7 papers); Description and presentation of DCD of SIS (6 papers); Results of experiences in engineering, manufacture, qualification operation of DCD hardware and software (5 papers). A separate abstract was prepared for each of these papers

  8. The Influence of a Radiant Panel System with Integrated Phase Change Material on Energy Use and Thermal Indoor Environment

    DEFF Research Database (Denmark)

    Nielsen, Lin Flemming; Bourdakis, Eleftherios; Kazanci, Ongun Berk

    2018-01-01

    This study examined the effect on energy use and thermal comfort when combining microencapsulated phase change material (PCM) with radiant ceiling panels in a two-person office. The performance of the system was studied during the cooling season in the climates of Copenhagen, Denmark, and Rome...

  9. Analysis of AC and DC Lighting Systems with 150-Watt Peak Solar Panel in Denpasar Based on NASA Data

    Science.gov (United States)

    Narottama, A. A. N. M.; Amerta Yasa, K.; Suwardana, I. W.; Sapteka, A. A. N. G.; Priambodo, P. S.

    2018-01-01

    Solar energy on the Earth’s surface has different magnitudes on every longitude and latitude. National Aeronautics and Space Administration (NASA) provides surface meteorology and solar energy database which can be accessed openly online. This database delivers information about Monthly Averaged Insolation Incident On A Horizontal Surface, Monthly Averaged Insolation Incident On A Horizontal Surface At Indicated GMT Times and also data about Equivalent Number Of No-Sun Or Black Days for any latitude and longitude. Therefore, we investigate the lighting systems with 150-Watt peak solar panel in Denpasar City, the capital province of Bali. Based on NASA data, we analyse the received wattage by a unit of 150-Watt peak solar panel in Denpasar City and the sustainability of 150-Watt peak solar panel to supply energy for 432-Watt hour/day AC and 360-Watt hour/day DC lighting systems using 1.2 kWh battery. The result shows that the maximum received wattage by a unit of 150-Watt peak solar panel is 0.76 kW/day in October. We concluded that the 1.2 kWh installed battery has higher capacity than the battery capacity needed in March, the month with highest no-sun days, for both AC and DC lighting systems. We calculate that the installed battery can be used to store the sustainable energy from sun needed by AC and DC lighting system for about 2.78 days and 3.51 days, consecutively.

  10. Smart nanogrid systems for disaster mitigation employing deployable renewable energy harvesting devices

    Science.gov (United States)

    Ghasemi-Nejhad, Mehrdad N.; Menendez, Michael; Minei, Brenden; Wong, Kyle; Gabrick, Caton; Thornton, Matsu; Ghorbani, Reza

    2016-04-01

    This paper explains the development of smart nanogrid systems for disaster mitigation employing deployable renewable energy harvesting, or Deployable Disaster Devices (D3), where wind turbines and solar panels are developed in modular forms, which can be tied together depending on the needed power. The D3 packages/units can be used: (1) as a standalone unit in case of a disaster where no source of power is available, (2) for a remote location such as a farm, camp site, or desert (3) for a community that converts energy usage from fossil fuels to Renewable Energy (RE) sources, or (4) in a community system as a source of renewable energy for grid-tie or off-grid operation. In Smart D3 system, the power is generated (1) for consumer energy needs, (2) charge storage devices (such as batteries, capacitors, etc.), (3) to deliver power to the network when the smart D3 nano-grid is tied to the network and when the power generation is larger than consumption and storage recharge needs, or (4) to draw power from the network when the smart D3 nano-grid is tied to the network and when the power generation is less than consumption and storage recharge needs. The power generated by the Smart D3 systems are routed through high efficiency inverters for proper DC to DC or DC to AC for final use or grid-tie operations. The power delivery from the D3 is 220v AC, 110v AC and 12v DC provide proper power for most electrical and electronic devices worldwide. The power supply is scalable, using a modular system that connects multiple units together. This are facilitated through devices such as external Input-Output or I/O ports. The size of the system can be scaled depending on how many accessory units are connected to the I/O ports on the primary unit. The primary unit is the brain of the system allowing for smart switching and load balancing of power input and smart regulation of power output. The Smart D3 systems are protected by ruggedized weather proof casings allowing for operation

  11. Application of Structured Light System Technique for Authentication of Wooden Panel Paintings

    Directory of Open Access Journals (Sweden)

    Fernando Buchón-Moragues

    2016-06-01

    Full Text Available This paper presents a new application of photogrammetric techniques for protecting cultural heritage. The accuracy of the method and the fact that it can be used to carry out different tests without contact between the sample and the instruments can make this technique very useful for authenticating and cataloging artworks. The application focuses on the field of pictorial artworks, and wooden panel paintings in particular. In these works, the orography formed by the brushstrokes can be easily digitalized using a photogrammetric technique, called Structured Light System, with submillimeter accuracy. Thus, some of the physical characteristics of the brushstrokes, like minimum and maximum heights or slopes become a fingerprint of the painting. We explain in detail the general principles of the Structured Light System Technique and the specific characteristics of the commercial set-up used in this work. Some experiments are carried out on a sample painted by us to check the accuracy limits of the technique and to propose some tests that can help to stablish a methodology for authentication purposes. Finally, some preliminary results obtained on a real pictorial artwork are presented, providing geometrical information of its metric features as an example of the possibilities of this application.

  12. Panel Analysis

    DEFF Research Database (Denmark)

    Brænder, Morten; Andersen, Lotte Bøgh

    2014-01-01

    where panel attrition, the practical and ethical challenges of contacting the same respondents at different points of time may affect response rates negatively. In the article, we present some key distinctions regarding panel data and analyses, and in the subsequent exercises we invite readers to apply...... these concepts on a number of recently published panel studies....

  13. Innovative wave energy device applied to coastal observatory systems

    Science.gov (United States)

    Marcelli, Marco; Bonamano, Simone; Piermattei, Viviana; Scanu, Sergio; Paladini de Mendoza, Francesco; Martellucci, Riccardo; Maximo, Peviani

    2017-04-01

    Marine environment is one of the most promising sources of renewable energy, whose exploitation could have an effect on several application fields. This work presents the design of an innovative device based on the Oscillating Water Column (OWC), that allows to convert wave energy into electricity, suitable for the typical Mediterranean wave climate. The flexibility of the device permits its installation either in deep or shallow waters, with reduced costs of deployment, maintenance and connection to the grid. Furthermore, the replicability of the design allows the device to be installed in array of several number of similar units. The technical concept is to convey the sea water within a vertical pipe, in which the water movements activate a rotor connected to a generator that transforms the energy of the water motion into electricity. The hydrodynamic design of the pipe is built to minimize the losses due to friction and turbulence and to exploit the maximum possible energy from wave motion. The wave energy is directly absorbed by the rotational movement of the turbine blades located in the water itself allowing a further reduction of the energy losses associated with the transformation of the linear water motion into electrical generation in the air phase (typical configuration of the OWC devices). In this work the device components are described considering two possible configurations that use a Wells turbine or a Bulb type turbine. The system can be realized at a low cost, because of the modularity of the device project, which allows large freedom of sizes and placements, being able to be installed both individually and in arrays. The modularity, associated with the fact that the main elements of the system are available on the market, makes the device particularly attractive from the economic point of view. Finally, it is realized with a high constructive flexibility: the proposed system can be transported floating and moored to existing coastal structures or

  14. Embedded Control System for Smart Walking Assistance Device.

    Science.gov (United States)

    Bosnak, Matevz; Skrjanc, Igor

    2017-03-01

    This paper presents the design and implementation of a unique control system for a smart hoist, a therapeutic device that is used in rehabilitation of walking. The control system features a unique human-machine interface that allows the human to intuitively control the system just by moving or rotating its body. The paper contains an overview of the complete system, including the design and implementation of custom sensors, dc servo motor controllers, communication interfaces and embedded-system based central control system. The prototype of the complete system was tested by conducting a 6-runs experiment on 11 subjects and results are showing that the proposed control system interface is indeed intuitive and simple to adopt by the user.

  15. Evaluation of patient exposure with Flat Panel Detector (FPD) in X-ray TV system

    International Nuclear Information System (INIS)

    Yamada, M.; Komiya, N.; Kawaguchi, A.; Suzuki, M.; Suzuki, Shoichi; Asada, Yasuki

    2008-01-01

    The use of flat-panel detector (FPD) systems in TV equipment for gastrointestinal tract examination is increasing. The use of FPD systems is believed to reduce the exposure dose. When our institution changed its TV equipment from an image intensifier (GE; MS90Tj) system to an FPD (Shimadzu; SONIALVISION safire DAR-3500) system, we measured the doses produced and carried out a comparative examination of the extent to which exposure could be reduced. Two TV systems were used. We used an analyzer to measure output waveform, tube voltage, and half-value layer (HVL), and an ionization chamber dosimeter to carry out dose-in-air measurements. Body thickness, number of image acquisitions, and fluoroscopy time are required for the calculation of entrance skin dose (ESD). We therefore measured body thicknesses in 1000 upper gastrointestinal tract (UGI) and barium enemas and obtained average body thicknesses for males and females by age group. Values used for number of image acquisitions and fluoroscopy times were the averages in our institution over a two-year period. When an I.I. system was used, the average ESD during UGI examination were 126.8 mGy fluoroscopy dose and 11.62 mGy imaging dose, for an average total dose of 138.42 mGy per examination. ESD during barium enema averaged 201.73 mGy fluoroscopy dose and 45.2 mGy imaging dose, for an average total dose of 246.92 mGy per examination. When an FPD system was used, the average ESD during UGI examination were 58.71 mGy fluoroscopy dose and 5.72 mGy imaging dose, for an average total dose of 64.43 mGy per examination. ESD during barium enema averaged 112.21 mGy fluoroscopy dose and 24.55 mGy imaging dose, for an average total dose of 136.76 mGy per examination. The use of an FPD system reduced both fluoroscopy dose and imaging dose by 50%. The number of TV systems equipped with FPD in Japan has increased from around 1300 in 2006 to around 1700 in 2007. The use of FPD systems can be expected to increase in future. This

  16. Paneling architectural freeform surfaces

    KAUST Repository

    Eigensatz, Michael

    2010-07-26

    The emergence of large-scale freeform shapes in architecture poses big challenges to the fabrication of such structures. A key problem is the approximation of the design surface by a union of patches, socalled panels, that can be manufactured with a selected technology at reasonable cost, while meeting the design intent and achieving the desired aesthetic quality of panel layout and surface smoothness. The production of curved panels is mostly based on molds. Since the cost of mold fabrication often dominates the panel cost, there is strong incentive to use the same mold for multiple panels. We cast the major practical requirements for architectural surface paneling, including mold reuse, into a global optimization framework that interleaves discrete and continuous optimization steps to minimize production cost while meeting user-specified quality constraints. The search space for optimization is mainly generated through controlled deviation from the design surface and tolerances on positional and normal continuity between neighboring panels. A novel 6-dimensional metric space allows us to quickly compute approximate inter-panel distances, which dramatically improves the performance of the optimization and enables the handling of complex arrangements with thousands of panels. The practical relevance of our system is demonstrated by paneling solutions for real, cutting-edge architectural freeform design projects. © 2010 ACM.

  17. Paneling architectural freeform surfaces

    KAUST Repository

    Eigensatz, Michael

    2010-07-25

    The emergence of large-scale freeform shapes in architecture poses big challenges to the fabrication of such structures. A key problem is the approximation of the design surface by a union of patches, so-called panels, that can be manufactured with a selected technology at reasonable cost, while meeting the design intent and achieving the desired aesthetic quality of panel layout and surface smoothness. The production of curved panels is mostly based on molds. Since the cost of mold fabrication often dominates the panel cost, there is strong incentive to use the same mold for multiple panels. We cast the major practical requirements for architectural surface paneling, including mold reuse, into a global optimization framework that interleaves discrete and continuous optimization steps to minimize production cost while meeting user-specified quality constraints. The search space for optimization is mainly generated through controlled deviation from the design surface and tolerances on positional and normal continuity between neighboring panels. A novel 6-dimensional metric space allows us to quickly compute approximate inter-panel distances, which dramatically improves the performance of the optimization and enables the handling of complex arrangements with thousands of panels. The practical relevance of our system is demonstrated by paneling solutions for real, cutting-edge architectural freeform design projects.

  18. Accelerated Aging System for Prognostics of Power Semiconductor Devices

    Science.gov (United States)

    Celaya, Jose R.; Vashchenko, Vladislav; Wysocki, Philip; Saha, Sankalita

    2010-01-01

    Prognostics is an engineering discipline that focuses on estimation of the health state of a component and the prediction of its remaining useful life (RUL) before failure. Health state estimation is based on actual conditions and it is fundamental for the prediction of RUL under anticipated future usage. Failure of electronic devices is of great concern as future aircraft will see an increase of electronics to drive and control safety-critical equipment throughout the aircraft. Therefore, development of prognostics solutions for electronics is of key importance. This paper presents an accelerated aging system for gate-controlled power transistors. This system allows for the understanding of the effects of failure mechanisms, and the identification of leading indicators of failure which are essential in the development of physics-based degradation models and RUL prediction. In particular, this system isolates electrical overstress from thermal overstress. Also, this system allows for a precise control of internal temperatures, enabling the exploration of intrinsic failure mechanisms not related to the device packaging. By controlling the temperature within safe operation levels of the device, accelerated aging is induced by electrical overstress only, avoiding the generation of thermal cycles. The temperature is controlled by active thermal-electric units. Several electrical and thermal signals are measured in-situ and recorded for further analysis in the identification of leading indicators of failures. This system, therefore, provides a unique capability in the exploration of different failure mechanisms and the identification of precursors of failure that can be used to provide a health management solution for electronic devices.

  19. Control system devices : architectures and supply channels overview.

    Energy Technology Data Exchange (ETDEWEB)

    Trent, Jason; Atkins, William Dee; Schwartz, Moses Daniel; Mulder, John C.

    2010-08-01

    This report describes a research project to examine the hardware used in automated control systems like those that control the electric grid. This report provides an overview of the vendors, architectures, and supply channels for a number of control system devices. The research itself represents an attempt to probe more deeply into the area of programmable logic controllers (PLCs) - the specialized digital computers that control individual processes within supervisory control and data acquisition (SCADA) systems. The report (1) provides an overview of control system networks and PLC architecture, (2) furnishes profiles for the top eight vendors in the PLC industry, (3) discusses the communications protocols used in different industries, and (4) analyzes the hardware used in several PLC devices. As part of the project, several PLCs were disassembled to identify constituent components. That information will direct the next step of the research, which will greatly increase our understanding of PLC security in both the hardware and software areas. Such an understanding is vital for discerning the potential national security impact of security flaws in these devices, as well as for developing proactive countermeasures.

  20. Symmetric miniaturized heating system for active microelectronic devices.

    Science.gov (United States)

    McCracken, Michael; Mayer, Michael; Jourard, Isaac; Moon, Jeong-Tak; Persic, John

    2010-07-01

    To qualify interconnect technologies such as microelectronic fine wire bonds for mass production of integrated circuit (IC) packages, it is necessary to perform accelerated aging tests, e.g., to age a device at an elevated temperature or to subject the device to thermal cycling and measure the decrease of interconnect quality. There are downsides to using conventional ovens for this as they are relatively large and have relatively slow temperature change rates, and if electrical connections are required between monitoring equipment and the device being heated, they must be located inside the oven and may be aged by the high temperatures. Addressing these downsides, a miniaturized heating system (minioven) is presented, which can heat individual IC packages containing the interconnects to be tested. The core of this system is a piece of copper cut from a square shaped tube with high resistance heating wire looped around it. Ceramic dual in-line packages are clamped against either open end of the core. One package contains a Pt100 temperature sensor and the other package contains the device to be aged placed in symmetry to the temperature sensor. According to the temperature detected by the Pt100, a proportional-integral-derivative controller adjusts the power supplied to the heating wire. The system maintains a dynamic temperature balance with the core hot and the two symmetric sides with electrical connections to the device under test at a cooler temperature. Only the face of the package containing the device is heated, while the socket holding it remains below 75 degrees C when the oven operates at 200 degrees C. The minioven can heat packages from room temperature up to 200 degrees C in less than 5 min and maintain this temperature at 28 W power. During long term aging, a temperature of 200 degrees C was maintained for 1120 h with negligible resistance change of the heating wires after 900 h (heating wire resistance increased 0.2% over the final 220 h). The

  1. Optical Tomography System: Charge-coupled Device Linear Image Sensors

    Directory of Open Access Journals (Sweden)

    M. Idroas

    2010-09-01

    Full Text Available This paper discussed an optical tomography system based on charge-coupled device (CCD linear image sensors. The developed system consists of a lighting system, a measurement section and a data acquisition system. Four CCD linear image sensors are configured around a flow pipe with an octagonal-shaped measurement section, for a four projections system. The four CCD linear image sensors consisting of 2048 pixels with a pixel size of 14 micron by 14 micron are used to produce a high-resolution system. A simple optical model is mapped into the system’s sensitivity matrix to relate the optical attenuation due to variations of optical density within the measurement section. A reconstructed tomographic image is produced based on the model using MATLAB software. The designed instrumentation system is calibrated and tested through different particle size measurements from different projections.

  2. MEMS- and NEMS-based smart devices and systems

    Science.gov (United States)

    Varadan, Vijay K.

    2001-11-01

    The microelectronics industry has seen explosive growth during the last thirty years. Extremely large markets for logic and memory devices have driven the development of new materials, and technologies for the fabrication of even more complex devices with features sized now don at the sub micron and nanometer level. Recent interest has arisen in employing these materials, tools and technologies for the fabrication of miniature sensors and actuators and their integration with electronic circuits to produce smart devices and systems. This effort offers the promise of: 1) increasing the performance and manufacturability of both sensors and actuators by exploiting new batch fabrication processes developed including micro stereo lithographic an micro molding techniques; 2) developing novel classes of materials and mechanical structures not possible previously, such as diamond like carbon, silicon carbide and carbon nanotubes, micro-turbines and micro-engines; 3) development of technologies for the system level and wafer level integration of micro components at the nanometer precision, such as self-assembly techniques and robotic manipulation; 4) development of control and communication systems for MEMS devices, such as optical and RF wireless, and power delivery systems, etc. A novel composite structure can be tailored by functionalizing carbon nano tubes and chemically bonding them with the polymer matrix e.g. block or graft copolymer, or even cross-linked copolymer, to impart exceptional structural, electronic and surface properties. Bio- and Mechanical-MEMS devices derived from this hybrid composite provide a new avenue for future smart systems. The integration of NEMS (NanoElectroMechanical Systems), MEMS, IDTs (Interdigital Transducers) and required microelectronics and conformal antenna in the multifunctional smart materials and composites results in a smart system suitable for sensing and control of a variety functions in automobile, aerospace, marine and civil

  3. Interface requirements in nuclear medicine devices and systems

    International Nuclear Information System (INIS)

    Maguire, G.Q. Jr.; Brill, A.B.; Noz, M.E.

    1982-01-01

    Interface designs for three nuclear medicine imaging systems, and computer networking strategies proposed for medical imaging departments are presented. Configurations for two positron-emission-tomography devices (PET III and ECAT) and a general-purpose tomography instrument (the UNICON) are analyzed in terms of specific performance parameters. Interface designs for these machines are contrasted in terms of utilization of standard versus custom modules, cost, and ease of modification, upgrade, and support. The requirements of general purpose systems for medical image analysis, display, and archiving, are considered, and a realizable state-of-the-art system is specfied, including a suggested timetable

  4. A portable air jet actuator device for mechanical system identification

    Science.gov (United States)

    Belden, Jesse; Staats, Wayne L.; Mazumdar, Anirban; Hunter, Ian W.

    2011-03-01

    System identification of limb mechanics can help diagnose ailments and can aid in the optimization of robotic limb control parameters and designs. An interesting fluid phenomenon—the Coandă effect—is utilized in a portable actuator to provide a stochastic binary force disturbance to a limb system. The design of the actuator is approached with the goal of creating a portable device which could be deployed on human or robotic limbs for in situ mechanical system identification. The viability of the device is demonstrated by identifying the parameters of an underdamped elastic beam system with fixed inertia and stiffness and variable damping. The nonparametric compliance impulse response yielded from the system identification is modeled as a second-order system and the resultant parameters are found to be in excellent agreement with those found using more traditional system identification techniques. The current design could be further miniaturized and developed as a portable, wireless, unrestrained mechanical system identification instrument for less intrusive and more widespread use.

  5. Automatic Number Plate Recognition System for IPhone Devices

    Directory of Open Access Journals (Sweden)

    Călin Enăchescu

    2013-06-01

    Full Text Available This paper presents a system for automatic number plate recognition, implemented for devices running the iOS operating system. The methods used for number plate recognition are based on existing methods, but optimized for devices with low hardware resources. To solve the task of automatic number plate recognition we have divided it into the following subtasks: image acquisition, localization of the number plate position on the image and character detection. The first subtask is performed by the camera of an iPhone, the second one is done using image pre-processing methods and template matching. For the character recognition we are using a feed-forward artificial neural network. Each of these methods is presented along with its results.

  6. Development of an Erlang System Adaopted to Embedded Devices

    OpenAIRE

    Andersson, Fredrik; Bergström, Fabian

    2011-01-01

    Erlang is a powerful and robust language for writing massively parallel and distributed applications. With the introduction of multi-core ARM processors, the embedded market will be looking for ways of taking advantage of the newfound opportunities for parallelism. To support the development of embedded applications using Erlang we want to provide Erlang and Embedded developers with a run-time system suited for embedded devices. We have managed to shrink the disk size of the Erlang runtime sy...

  7. Biomedical materials, devices and drug delivery systems by radiation techniques

    International Nuclear Information System (INIS)

    Kaetsu, Isao.

    1996-01-01

    The study of radiation polymerization in a super-cooled state started in 1966 and has been applied to the immobilization of biofunctional materials since 1973. In the last twenty years, application has been concentrated on the immobilization of drugs and hormones for the purpose of drug delivery systems. Very recently, the author has proposed a concept of environmental signal responsive chemical delivery system, as a new generation of controlled release and delivery systems. The study and development of materials, devices and systems is described. The signal responsive delivery system consists of a sensor part and a controlled delivery part. Therefore, the use of immobilization techniques for the biochip sensor and the hydrogel actuator has been investigated. As a future goal, systems for brain research are to be designed and studied. (author)

  8. Solar panel parallel mounting configuration

    Science.gov (United States)

    Mutschler, Jr., Edward Charles (Inventor)

    1998-01-01

    A spacecraft includes a plurality of solar panels interconnected with a power coupler and an electrically operated device to provide power to the device when the solar cells are insolated. The solar panels are subject to bending distortion when entering or leaving eclipse. Spacecraft attitude disturbances are reduced by mounting each of the solar panels to an elongated boom made from a material with a low coefficient of thermal expansion, so that the bending of one panel is not communicated to the next. The boom may be insulated to reduce its bending during changes in insolation. A particularly advantageous embodiment mounts each panel to the boom with a single mounting, which may be a hinge. The single mounting prevents transfer of bending moments from the panel to the boom.

  9. Building elements and systems using vacuum insulated panels in external walling; Bauelemente und Systeme mit VIP fuer Aussenwandkonstruktionen

    Energy Technology Data Exchange (ETDEWEB)

    Binz, A.; Steinke, G.

    2008-07-01

    This illustrated report for the Swiss Federal Office of Energy (SFOE) takes a look at a research project concerning vacuum-insulated building elements and systems. The advantages of the thin vacuum insulation panels (VIP) are listed and compared with the increasingly thick layers of conventional insulation required for low energy consumption buildings that meet so-called 'passive house' standard. The aims of the research project are discussed which addressed the particular requirements placed on the materials and their protection against external damage. The monitoring of vacuum state using RFID chips is discussed. Various protective elements are examined. Also, facade constructions and the avoidance of thermal short circuits are discussed. Illustrated examples of applications are presented and developments in this fast-moving area are commented on.

  10. Solar panel cleaning robot

    Science.gov (United States)

    Nalladhimmu, Pavan Kumar Reddy; Priyadarshini, S.

    2018-04-01

    As the demand of electricity is increasing, there is need to using the renewable sources to produce the energy at present of power shortage, the use of solar energy could be beneficial to great extent and easy to get the maximum efficiency. There is an urgent in improving the efficiency of solar power generation. Current solar panels setups take a major power loss when unwanted obstructions cover the surface of the panels. To make solar energy more efficiency of solar array systems must be maximized efficiency evaluation of PV panels, that has been discussed with particular attention to the presence of dust on the efficiency of the PV panels have been highlighted. This paper gives the how the solar panel cleaning system works and designing of the cleaning system.

  11. Energy management in mobile devices with the cinder operating system

    KAUST Repository

    Roy, Arjun

    2011-01-01

    We argue that controlling energy allocation is an increasingly useful and important feature for operating systems, especially on mobile devices. We present two new low-level abstractions in the Cinder operating system, reserves and taps, which store and distribute energy for application use. We identify three key properties of control - isolation, delegation, and subdivision - and show how using these abstractions can achieve them. We also show how the architecture of the HiStar information-flow control kernel lends itself well to energy control. We prototype and evaluate Cinder on a popular smartphone, the Android G1. Copyright © 2011 ACM.

  12. Reliable Integration of Terascale Systems with Nanoscale Devices

    Science.gov (United States)

    Naeimi, Helia

    Nanotechnology design has attracted considerable attention in recent years and seems to be the technology for the future generation of the electronic devices, either as scaled and more restricted conventional lithographic technology, or as emerging sublithographic technologies, such as nanowires, carbon nanotubes, NDR (Negative Differential Resistance) devices, or other nanotechnology devices. Each of these technologies provides one or more design benefits including feature-size scaling, high on-off ratios, and faster devices. However, all of these techniques share their most challenging design issue: reliability. Providing reliability is becoming constantly more challenging due to increases in both the device failure rate and system complexity. This work develops techniques that make achieving reliability in such systems feasible with practical area overhead and considerable improvement in area overhead and system reliability compared to related techniques. Conventional reliability techniques focus on low defect and fault rates, i.e., single event upset (SEU). These techniques cannot simply be scaled to larger systems with more unreliable devices. If these techniques are directly applied to the high defect and fault rate of the nanotechnology regime, they suffer impractically high overhead, or they may not achieve the desired reliability. Our approach in this thesis exploits the following design patterns to achieve a considerable area reduction compared to related works and achieve high reliability: (1) Fine-grained reliability: In this technique, the system is partitioned into fine-grained blocks, and the reliability is provided for each block. This technique is used to contain the area overhead and bound the impact on the throughput. (2) Using alternative resources: This technique improves the design quality by sparing other resources when system is tight on one resource. In our work we replace some of the spacial redundancies with temporal redundancy to limit

  13. Panel discussion

    Energy Technology Data Exchange (ETDEWEB)

    No Author Given

    1975-01-01

    Panel discussion: summation and future projections. Introductory remarks by panelists followed by questions and comments from the floor. Panelists: Dr. Joseph Barnea (former director of Resources and Transport for the United Nations; energy consultant to the United Nations Institute for Training and Research (UNITAR)); the Honorable Clyde F. Bel, Jr. (member of the Louisiana House of Representatives representing District 90 and New Orleans); Dr. David Lombard (acting chief of the Advanced Systems Branch of the Division of Geothermal Energy Research and Technology, Energy Research and Development Administration (ERDA)); Fred C. Repper (vice-president of Central Power and Light Company in Corpus Christi, Texas); Dr. Hans Suter (environmental consultant in Corpus Christi, Texas; environmental columnist for the Corpus Christi Caller Times). Session chairman: Herbert Woodson.

  14. Aerothermoelastic response analysis for C/SiC panel of ceramic matrix composite shingle thermal protection system

    Science.gov (United States)

    Huo, Lin; Cheng, Xing-Hua; Yang, Tao

    2015-05-01

    This paper presents a study of aerothermoelastic response of a C/SiC panel, which is a primary structure for ceramic matrix composite shingle thermal protection system for hypersonic vehicles. It is based on a three dimensional thermal protection shingle panel on a quasi-waverider vehicle model. Firstly, the Thin Shock Layer and piston theory are adopted to compute the aerodynamic pressure of rigid body and deformable body, and a series of engineering methods are used to compute the aerodynamic heating. Then an aerothermoelastic loosely-coupled time marching strategy and self-adapting aerodynamic heating time step are developed to analyze the aerothermoelastic response of the panel, with an aerodynamic heating and temperature field coupling parameter selection method being adopted to increase the efficiency. Finally, a few revealing conclusions are reached by analyzing how coupling at different degrees influences the quasi-static aerothermoelastic response of the panel and how aerodynamic pressure of rigid body time step influences the quasi-static aerothermoelastic response on a glide trajectory.

  15. Measurement of joint kinematics using a conventional clinical single-perspective flat-panel radiography system

    International Nuclear Information System (INIS)

    Seslija, Petar; Teeter, Matthew G.; Yuan Xunhua; Naudie, Douglas D. R.; Bourne, Robert B.; MacDonald, Steven J.; Peters, Terry M.; Holdsworth, David W.

    2012-01-01

    Purpose: The ability to accurately measure joint kinematics is an important tool in studying both normal joint function and pathologies associated with injury and disease. The purpose of this study is to evaluate the efficacy, accuracy, precision, and clinical safety of measuring 3D joint motion using a conventional flat-panel radiography system prior to its application in an in vivo study. Methods: An automated, image-based tracking algorithm was implemented to measure the three-dimensional pose of a sparse object from a two-dimensional radiographic projection. The algorithm was tested to determine its efficiency and failure rate, defined as the number of image frames where automated tracking failed, or required user intervention. The accuracy and precision of measuring three-dimensional motion were assessed using a robotic controlled, tibiofemoral knee phantom programmed to mimic a subject with a total knee replacement performing a stair ascent activity. Accuracy was assessed by comparing the measurements of the single-plane radiographic tracking technique to those of an optical tracking system, and quantified by the measurement discrepancy between the two systems using the Bland–Altman technique. Precision was assessed through a series of repeated measurements of the tibiofemoral kinematics, and was quantified using the across-trial deviations of the repeated kinematic measurements. The safety of the imaging procedure was assessed by measuring the effective dose of ionizing radiation associated with the x-ray exposures, and analyzing its relative risk to a human subject. Results: The automated tracking algorithm displayed a failure rate of 2% and achieved an average computational throughput of 8 image frames/s. Mean differences between the radiographic and optical measurements for translations and rotations were less than 0.08 mm and 0.07° in-plane, and 0.24 mm and 0.6° out-of-plane. The repeatability of kinematics measurements performed using the

  16. Control room, emergency control system and local control panels in nuclear power plants

    International Nuclear Information System (INIS)

    1988-01-01

    The requirements on planning and construction of control boards including ergonomic-technical designing are specified in this rule. The specifications put the requirements on the design of place, process and environment of work, which are mentioned in the sections 90 and 91 of the labor-management relations act, into more concrete terms for the safety-relevant control panels as work places in a nuclear power station. The work places at control panels are not considered as video workstations in the sense of the 'Safety Rules for Video Workstations in the Office Sector' published by the General Association of the Industrial Trade Associations. The requirements are based on the operation and information technology realized at present in control panels of stationary nuclear power plants. (orig./HP) [de

  17. A flat-panel detector based micro-CT system: performance evaluation for small-animal imaging

    Science.gov (United States)

    Lee, Sang Chul; Kim, Ho Kyung; Chun, In Kon; Hye Cho, Myung; Lee, Soo Yeol; Cho, Min Hyoung

    2003-12-01

    A dedicated small-animal x-ray micro computed tomography (micro-CT) system has been developed to screen laboratory small animals such as mice and rats. The micro-CT system consists of an indirect-detection flat-panel x-ray detector with a field-of-view of 120 × 120 mm2, a microfocus x-ray source, a rotational subject holder and a parallel data processing system. The flat-panel detector is based on a matrix-addressed photodiode array fabricated by a CMOS (complementary metal-oxide semiconductor) process coupled to a CsI:Tl (thallium-doped caesium iodide) scintillator as an x-ray-to-light converter. Principal imaging performances of the micro-CT system have been evaluated in terms of image uniformity, voxel noise and spatial resolution. It has been found that the image non-uniformity mainly comes from the structural non-uniform sensitivity pattern of the flat-panel detector and the voxel noise is about 48 CT numbers at the voxel size of 100 × 100 × 200 µm3 and the air kerma of 286 mGy. When the magnification ratio is 2, the spatial resolution of the micro-CT system is about 14 lp/mm (line pairs per millimetre) that is almost determined by the flat-panel detector showing about 7 lp/mm resolving power. Through low-contrast phantom imaging studies, the minimum resolvable contrast has been found to be less than 36 CT numbers at the air kerma of 95 mGy. Some laboratory rat imaging results are presented.

  18. Tritium Systems Test Assembly: design for major device fabrication review

    International Nuclear Information System (INIS)

    Anderson, J.L.; Sherman, R.H.

    1977-06-01

    This document has been prepared for the Major Device Fabrication Review for the Tritium Systems Test Assembly (TSTA). The TSTA is dedicated to the development, demonstration, and interfacing of technologies related to the deuterium-tritium fuel cycle for fusion reactor systems. The principal objectives for TSTA are: (a) demonstrate the fuel cycle for fusion reactor systems; (b) develop test and qualify equipment for tritium service in the fusion program; (c) develop and test environmental and personnel protective systems; (d) evaluate long-term reliability of components; (e) demonstrate long-term safe handling of tritium with no major releases or incidents; and (f) investigate and evaluate the response of the fuel cycle and environmental packages to normal, off-normal, and emergency situations. This document presents the current status of a conceptual design and cost estimate for TSTA. The total cost to design, construct, and operate TSTA through FY-1981 is estimated to be approximately $12.2 M

  19. Heating control device for nuclear reactor cooling systems

    International Nuclear Information System (INIS)

    Kishigawa, Osamu.

    1981-01-01

    Purpose: To obtain a heating control device capable of surely preventing deformations and fluctures due to thermal stresses in equipments such as tanks and pipeways upon starting of reactor operation. Constitution: A heating control device for nuclear reactor cooling systems using metal coolants comprises a plurality of heaters disposed at each of the sections in the cooling systems for heating the coolants, temperature detectors for the detection of temperature at each of the sections in the cooling systems to be heated by the heaters, a circuit for judging the range of filling process of the metal coolants in the cooling systems, a coefficient change circuit for heating control for changing and setting the coefficient for the heating control by the heaters based on the information for the range judged by the judging circuit, and a circuit for controlling the input to each of the heaters based on the output signals for the coefficient change circuit and the signals from the temperature detectors. (Seki, T.)

  20. Control device for start-up of reactor depressurization system

    International Nuclear Information System (INIS)

    Suzuki, Hiroshi; Saito, Minoru; Oda, Shingo; Miura, Satoshi; Hashimoto, Koji; Tate, Hitoshi; Fujii, Kazunobu

    1998-01-01

    The present invention concerns are emergency reactor core cooling system (ECCS) of a BWR type reactor and provides a control device for start-up of an automatic depressurization system. Namely, the device has an object of preventing erroneous opening of a main steam escape safety value when testing a start-up signal circuit of an automatic depressurization system for testing the automatic depressurization system. A start-up signal circuit receives both signals of a reactor container pressure high signal and a reactor pressure vessel water level low signal and outputs an automatic start-up signal for compulsorily opening a main steam escape safety valve automatically. A test switch having a self-holding circuit is disposed to a central control chamber. A test signal circuit is disposed for preventing transfer of an erroneous start-up signal to the main steam escape safety valve due to a simulation signal during output test signals by the test switch. (I.S.)

  1. An optical system via liquid crystal photonic devices for photobiomodulation.

    Science.gov (United States)

    Chang, Chia-Ming; Lin, Yi-Hsin; Srivastava, Abhishek Kumar; Chigrinov, Vladimir Grigorievich

    2018-03-09

    Photobiomodulation or low-level light therapy (LLLT) has extensive applications based on light-induced effects in biological systems. Photobiomodulation remains controversial because of a poorly understood biochemical mechanism limited by the well-known biphasic dose response or Arndt-Schulz curve. The Arndt-Schulz curve states that an optimal dose of light is a key factor for realizing a therapeutic effect. In this report, we demonstrate a tunable optical system for photobiomodulation to aid physicians in overcoming the constraints of light due to biphasic dose response. The tunable optical system is based on a white light-emitting diode and four liquid crystal (LC) photonic devices: three LC phase retarders, and one LC lens. The output light of the tunable optical system exhibits electrical tunability for the wavelength, energy density and beam size. The operating principle is introduced, and the experimental results are presented. The proposed concept can be further extended to other electrically tunable photonic devices for different clinical purposes for photobiomodulation.

  2. Efficiency improvements of photo-voltaic panels using a sun - tracking system

    International Nuclear Information System (INIS)

    Al-Mohamad, A.

    2005-01-01

    This paper presents a sun-tracking design, whereby the movement of a photo-voltaic module was controlled to follow the Sun's radiation using a programmable logic-controller unit (PLC). All electronic circuits and the necessary software have been designed and developed to perform the technical tasks. A PLC unit was employed to control and monitor the mechanical movement of the PV module and to collect and store data related to the Sun's radiation. It is found that the daily output the power of the PV was increased by more than 20% in comparison with that of a fixed module. The PV-tracking system can be employed as a standalone device and it could be connected to a personal computer through the RS232 serial port to monitor the whole process on a computer screen. (author)

  3. Efficiency improvements of photo-voltaic panels using a Sun-tracking system

    International Nuclear Information System (INIS)

    Al-Mohamad, Ali

    2004-01-01

    This paper presents a Sun-tracking design, whereby the movement of a photo-voltaic module was controlled to follow the Sun's radiation using a programmable logic-controller (PLC) unit. All electronic circuits and the necessary software have been designed and developed to perform the technical tasks. A PLC unit was employed to control and monitor the mechanical movement of the PV module and to collect and store data related to the Sun's radiation. It is found that the daily output power of the PV was increased by more than 20% in comparison with that of a fixed module. The PV-tracking system can be employed as a stand-alone device and it could be connected to a personal computer through the RS232 serial port to monitor the whole process on a computer screen

  4. [Methodology for construction of a panel of indicators for monitoring and evaluation of unified health system (SUS) management].

    Science.gov (United States)

    Tamaki, Edson Mamoru; Tanaka, Oswaldo Yoshimi; Felisberto, Eronildo; Alves, Cinthia Kalyne de Almeida; Drumond Junior, Marcos; Bezerra, Luciana Caroline de Albuquerque; Calvo, Maria Cristina Marino; Miranda, Alcides Silva de

    2012-04-01

    This study sought to develop methodology for the construction of a Panel for the Monitoring and Evaluation of Management of the Unified Health System (SUS). The participative process used in addition to the systematization conducted made it possible to identify an effective strategy for building management tools in partnership with researchers, academic institutions and managers of the SUS. The final systematization of the Panel selected indicators for the management of the SUS in terms of Demand, Inputs, Processes, Outputs and Outcomes in order to provide a simple, versatile and useful tool for evaluation at any level of management and more transparent and easier communication with all stakeholders in decision-making. Taking the management of the SUS as the scope of these processes and practices in all normative aspects enabled dialog between systemic theories and those which consider the centrality of the social actor in the decision-making process.

  5. Automatic Color Sorting System for Hardwood Edge-Glued Panel Parts

    Science.gov (United States)

    Richard W. Conners; D.Earl Kline; Philip A. Araman

    1996-01-01

    The color sorting of edge-glued panel parts is becoming more important in the manufacture of hardwood products. Consumers, while admiring the natural appearance of hardwoods, do not like excessive color variation across product surfaces. Color uniformity is particularly important today because of the popularity of lightly stained products. Unfortunately, color sorting...

  6. Potential Usage of Thermoelectric Devices in a HTPEMFC System

    DEFF Research Database (Denmark)

    Xin, Gao; Chen, Min; Andreasen, Søren Juhl

    of thermoelectric (TE) devices to release this Li-ion dependence has been preliminarily evaluated. Firstly, following the HTPEMFC stack or the methanol reformer, TEGs are embedded inside a gas-liquid heat exchanger to jointly form a TE recovery subsystem for electricity production. A finite-difference model...... coolers are integrated into the methanol evaporator to reduce the heat loss herein during the HTPEMFC power system startup. It is believed that by reducing this heat loss, the electricity consumption by the evaporator during startup can be steadily reduced. Through the heat-electricity conversion...

  7. Establishment and application of Competitive Intelligence System in Mobile Devices

    Directory of Open Access Journals (Sweden)

    Anass El Haddadi

    2011-12-01

    Full Text Available The strategy concept has changed dramatically: from a long range planning to strategic planning then to strategic responsiveness. This response implies moving from a concept of change to a concept of continuous evolution. In our context, the competitive intelligence system presented aims to improve decision‐making in all aspects of business life, particularly for offensive and innovative decisions. In the paper we present XPlor EveryWhere, our competitive intelligence system based on a multidimensional analysis model for mobile devices. The objective of this system is to capture the information environment in all dimensions of a decision problem, with the exploitation of information by analyzing the evolution of their interactions

  8. Color quality management in advanced flat panel display engines

    Science.gov (United States)

    Lebowsky, Fritz; Neugebauer, Charles F.; Marnatti, David M.

    2003-01-01

    During recent years color reproduction systems for consumer needs have experienced various difficulties. In particular, flat panels and printers could not reach a satisfactory color match. The RGB image stored on an Internet server of a retailer did not show the desired colors on a consumer display device or printer device. STMicroelectronics addresses this important color reproduction issue inside their advanced display engines using novel algorithms targeted for low cost consumer flat panels. Using a new and genuine RGB color space transformation, which combines a gamma correction Look-Up-Table, tetrahedrization, and linear interpolation, we satisfy market demands.

  9. 75 FR 391 - Medical Device Quality System Regulation Educational Forum on Risk Management Through the Product...

    Science.gov (United States)

    2010-01-05

    ... Cycle; Public Workshop AGENCY: Food and Drug Administration, HHS. ACTION: Notice of public workshop...), is announcing a public workshop entitled ``Medical Device Quality System Regulation Educational Forum... information about FDA's Medical Device Quality Systems Regulation (QSR) to the regulated industry...

  10. Diagnosis of the Main Busbar II Panel Components Ageing of RSG-GAS Electrical System by Using Infrared Thermography

    International Nuclear Information System (INIS)

    Teguh Sulistyo; Kiswanto; Roziq Himawan; Ari Satmoko

    2007-01-01

    To support the operation of RSG-GAS safely, the diagnosis of the ageing of main busbar II BHD/BHE/BHF panel components of RSG-GAS electrical system have been done. By using infrared thermography type Thermo Tracer TH9100PM VI/PW VI. The results of the diagnosis showed that some of the components under degradation with various rate. It can cause the system failure. By understanding the components ageing degradation mechanism and performing the preventive and predictive maintenance and safety of RSG-GAS electrical system earlier, the possibility of accident can be avoided. (author)

  11. Developing a HACCP-like system for improving animal health and welfare in organic egg production - based on an expert panel analysis

    DEFF Research Database (Denmark)

    Hegelund, Lene; Sørensen, Jan Tind

    2007-01-01

    In the process of developing a generic Hazard Analysis and Critical Control Point (HACCP)-like system for securing animal health and welfare in organic egg production, an expert panel analysis was used to perform the initial hazard analysis. Eighteen advisers and researchers in organic egg...... production were included in the expert panel. In a series of four questionnaires, the expert panel first scored 34 health and welfare problems seen in Danish organic egg production. Based on scorings of severity and occurrence, 10 problems were selected for further analysis. The experts subsequently...... specific systems. An expert panel analysis based on questionnaires was a useful tool during the first steps of developing a HACCP plan, conducting a hazard analysis and suggesting control points. However, care should be taken regarding the panel's size and fields of expertise in order to assure...

  12. Rational Design of Composite Panels

    DEFF Research Database (Denmark)

    Riber, Hans Jørgen

    1996-01-01

    panels as well as single-skin panels, the effect of shear is included. The finite difference method is used solving the system of governing plate equations. Laterally loaded panels are analysed with respect to mid-point deflections and stresses. The numerical results are discussed in the light of 'Det...

  13. Smart wave filtering method of a rectangular panel using Hilbert transformers and its application to an adaptive control system

    International Nuclear Information System (INIS)

    Iwamoto, Hiroyuki; Tanaka, Nobuo; Hill, Simon G

    2010-01-01

    This paper concerns the active vibration control of a rectangular panel using smart sensors from the viewpoint of an active wave control theory. The objective of this paper is to present a new type of filter which enables the measurement of the wave amplitude of a rectangular panel in real time for the application of an adaptive feedforward control system which inactivates vibration modes. Firstly, a novel wave filtering method using smart PVDF sensors is proposed. It is found that the shaping function of smart sensors is a complex function. To realize the smart sensor in a practical situation, a Hilbert transformer is utilized to implement a phase shifter of 90° for broadband frequencies. Then, from the viewpoint of a numerical analysis, the characteristics of the proposed wave filter and the performance of the adaptive feedforward control system using the wave filter are discussed. Finally, experiments implementing the active wave control theory which uses the proposed wave filter are conducted, demonstrating the validity of the proposed method in suppressing the vibration of a rectangular panel

  14. Clinical evaluation of digital angiographic system equipped with the Safire' flat-panel detector of a direct conversion type

    International Nuclear Information System (INIS)

    Miura, Yoshiaki; Miura, Yusuke; Goto, Keiichi

    2003-01-01

    This report presents a report on clinical evaluation of our newly developed flat-panel X-ray detector of a direct conversion type, designed to provide images of a resolution higher than, or at least equal to, that ensured by X-ray photographic films, in clinical digital X-ray cinematography. This new detector was named 'Safire' the acronym of 'Shimadzu advanced flat imaging receptor', emphasizing its high technological level, such as the capability to ensure high quality of images. The clinical evaluation of Shimadzu DIGITEX Premier digital angiography system, equipped with this new flat-panel X-ray detector of a direct conversion type, has been started in March, 2003, at the Kokura Memorial Hospital in Kyushu, Japan. (author)

  15. 78 FR 79300 - Cardiovascular Devices; Reclassification of Intra-Aortic Balloon and Control Systems for Acute...

    Science.gov (United States)

    2013-12-30

    .... FDA-2013-N-0581] Cardiovascular Devices; Reclassification of Intra-Aortic Balloon and Control Systems... of these devices into class II. List of Subjects in 21 CFR Part 870 Medical devices, Cardiovascular... Commissioner of Food and Drugs, 21 CFR part 870 is amended as follows: PART 870--CARDIOVASCULAR DEVICES 0 1...

  16. A Text-Independent Speaker Authentication System for Mobile Devices

    Directory of Open Access Journals (Sweden)

    Florentin Thullier

    2017-09-01

    Full Text Available This paper presents a text independent speaker authentication method adapted to mobile devices. Special attention was placed on delivering a fully operational application, which admits a sufficient reliability level and an efficient functioning. To this end, we have excluded the need for any network communication. Hence, we opted for the completion of both the training and the identification processes directly on the mobile device through the extraction of linear prediction cepstral coefficients and the naive Bayes algorithm as the classifier. Furthermore, the authentication decision is enhanced to overcome misidentification through access privileges that the user should attribute to each application beforehand. To evaluate the proposed authentication system, eleven participants were involved in the experiment, conducted in quiet and noisy environments. Public speech corpora were also employed to compare this implementation to existing methods. Results were efficient regarding mobile resources’ consumption. The overall classification performance obtained was accurate with a small number of samples. Then, it appeared that our authentication system might be used as a first security layer, but also as part of a multilayer authentication, or as a fall-back mechanism.

  17. 78 FR 31576 - Enforcement Proceeding; Certain Two-Way Global Satellite Communication Devices, System and...

    Science.gov (United States)

    2013-05-24

    ...-Way Global Satellite Communication Devices, System and Components Thereof; Notice of Institution of... importation of certain two-way global satellite communication devices, system and components thereof by reason... importation any two-way global satellite communication devices, system, and components thereof that infringe...

  18. 30 CFR 75.1101-10 - Water sprinkler systems; fire warning devices at belt drives.

    Science.gov (United States)

    2010-07-01

    ... Protection § 75.1101-10 Water sprinkler systems; fire warning devices at belt drives. Each water sprinkler system shall be equipped with a device designed to stop the belt drive in the event of a rise in... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Water sprinkler systems; fire warning devices...

  19. 29 CFR Appendix D to Subpart M of... - Positioning Device Systems

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 8 2010-07-01 2010-07-01 false Positioning Device Systems D Appendix D to Subpart M of..., Subpt. M, App. D Appendix D to Subpart M of Part 1926—Positioning Device Systems Non-Mandatory Guidelines for Complying With § 1926.502(e) I. Testing Methods For Positioning Device Systems. This appendix...

  20. Optimization of a flat-panel based real time dual-energy system for cardiac imaging

    International Nuclear Information System (INIS)

    Ducote, Justin L.; Xu Tong; Molloi, Sabee

    2006-01-01

    A simulation study was conducted to evaluate the effects of high-energy beam filtration, dual-gain operation and noise reduction on dual-energy images using a digital flat-panel detector. High-energy beam filtration increases image contrast through greater beam separation and tends to reduce total radiation exposure and dose per image pair. It is also possible to reduce dual-energy image noise by acquiring low and high-energy images at two different detector gains. In addition, dual-energy noise reduction algorithms can further reduce image noise. The cumulative effect of these techniques applied in series was investigated in this study. The contrast from a small thickness of calcium was simulated over a step phantom of tissue equivalent material with a CsI phosphor as the image detector. The dual-energy contrast-to-noise ratio was calculated using values of energy absorption and energy variance. A figure-of-merit (FOM) was calculated from dual-energy contrast-to-noise ratio (CNR) and patient effective dose estimated from values of entrance exposure. Filter atomic numbers in the range of 1-100 were considered with thicknesses ranging from 0-2500 mg/cm 2 . The simulation examined combinations of the above techniques which maximized the FOM. The application of a filter increased image contrast by as much as 45%. Near maximal increases were seen for filter atomic numbers in the range of 40-60 and 85-100 with masses above 750 mg/cm 2 . Increasing filter thickness beyond 1000 mg/cm 2 increased tube loading without further significant contrast enhancement. No additional FOM improvements were seen with dual gain before or after the application of any noise reduction algorithm. Narrow beam experiments were carried out to verify predictions. The measured FOM increased by more than a factor of 3.5 for a silver filter thickness of 800 μm, equal energy weighting and application of a noise clipping algorithm. The main limitation of dynamic high-energy filtration is increased

  1. Time stress measurement device: system design and synthesis

    Science.gov (United States)

    Harchani, Noursaied; Jimenez, Fernando; Al-Mohammed, Mohammed; Esteve, Daniel; Courvoisier, M.

    2000-04-01

    System design methodology becomes a strategic activity in the industrial competition. Obtaining substantial reduction of time to market for complex and reliable products is one of the priorities for the manufacturers. Top down design, automated generation of architecture, co-design, virtual prototyping, etc. are already identified as research topics which have to be privileged. To be efficient, each theoretical contribution must be inserted in a global procedure of project management where complementary elements such as marketing, technico-economic survey, road-mapping, internal know-how,.. must be considered. In this context, this paper will present a design methodology starting from the requirement statement until the technical realization of the product, and applied to the design of a Time Stress Measurement Device for the observation of aeronautical mechanical systems.

  2. Material Research of Rotary Sealing Device for Combined Cutting System

    Directory of Open Access Journals (Sweden)

    Rui Zeng

    2017-01-01

    Full Text Available In order to solve the rotary sealing problem of rotary shaft in drum shearer combined cutting system, the material and structure of combined cutting system rotary sealing device needs to be selected and designed. In the paper, the rotary sealing structure of four grades in series was designed first, and then the material of NBR-40 and PTFE 4FT-4 under the separate static and dynamic sealing tests were carried out on the combined tooth-slip-ring sealing test-bed. The tests show that the NBR-40 O-Ring with PTFE 4FT-4 tooth-slip-ring has no low-pressure leakage problem and low leakage in the sealing progress, the sealing effect of which is the best.

  3. Improving escape panel selectivity in Nephrops directed fisheries by actively stimulating fish behaviour

    DEFF Research Database (Denmark)

    Krag, Ludvig Ahm; Herrmann, Bent; Feekings, Jordan P.

    2017-01-01

    with it. To increase the efficiency of such panels, the contact probability needs to be improved. In this study, we investigate to what extent the efficiency of escape panels can be improved by actively stimulating the escape behaviour of fish. The performance of two identical panel sections was compared...... in a twin-trawl system, one with and one without a stimulation device. A new coupled analysis method was used to explicitly quantify the improvements in contact probability and release efficiency for the escape panel. The results demonstrate that by actively stimulating escape behaviour, the contact...

  4. VES PANEL (by invitation): Advancement and Enhanced Integration of Digital Technology Systems, VR Applications, CPS-Systems and Tools for Design Engineering

    NARCIS (Netherlands)

    Wendrich, Robert E.; Lim, Theodore; Baalsrud Hauge, Jannicke; Vitali, Andrea

    2018-01-01

    The purpose of this VES panel is to encourage discussion and exchange of views about current and new trends for Virtual and Immersive/Blended Systems and the transference of knowledge over multiple domains. As the market and/or industrial interest in virtual environments increase, new technologies

  5. Can FDI promote export diversification and sophistication of host countries? : dynamic panel system GMM analysis

    OpenAIRE

    Iwamoto, Manabu; Nabeshima, Kaoru

    2012-01-01

    Recent trade literature highlights the importance of export diversification and upgrading in fostering faster and sustainable economic growth. This study investigates the impact of FDI inflow and stock on the level of export diversification and sophistication in host country's export baskets. By utilizing the dynamic panel data model, we find that the five-year lagged FDI inflow correlates positively with both export diversification and sophistication, and FDI stock makes the positive contrib...

  6. System Estimation of Panel Data Models under Long-Range Dependence

    DEFF Research Database (Denmark)

    Ergemen, Yunus Emre

    using conditional-sum-of-squares criteria based on projected series by which latent characteristics are proxied. Resulting estimates are consistent and asymptotically normal at standard parametric rates. A simulation study provides reliability on the estimation method. The method is then applied......A general dynamic panel data model is considered that incorporates individual and interactive fixed effects allowing for contemporaneous correlation in model innovations. The model accommodates general stationary or nonstationary long-range dependence through interactive fixed effects...

  7. Photovoltaic cell electrical heating system for removing snow on panel including verification.

    Science.gov (United States)

    Weiss, Agnes; Weiss, Helmut

    2017-11-16

    Small photovoltaic plants in private ownership are typically rated at 5 kW (peak). The panels are mounted on roofs at a decline angle of 20° to 45°. In winter time, a dense layer of snow at a width of e.g., 10 cm keeps off solar radiation from the photovoltaic cells for weeks under continental climate conditions. Practically, no energy is produced over the time of snow coverage. Only until outside air temperature has risen high enough for a rather long-time interval to allow partial melting of snow; the snow layer rushes down in an avalanche. Following this proposal, snow removal can be arranged electrically at an extremely positive energy balance in a fast way. A photovoltaic cell is a large junction area diode inside with a threshold voltage of about 0.6 to 0.7 V (depending on temperature). This forward voltage drop created by an externally driven current through the modules can be efficiently used to provide well-distributed heat dissipation at the cell and further on at the glass surface of the whole panel. The adhesion of snow on glass is widely reduced through this heating in case a thin water film can be produced by this external short time heating. Laboratory experiments provided a temperature increase through rated panel current of more than 10 °C within about 10 min. This heating can initiate the avalanche for snow removal on intention as described before provided the clamping effect on snow at the edge of the panel frame is overcome by an additional heating foil. Basics of internal cell heat production, heating thermal effects in time course, thermographic measurements on temperature distribution, power circuit opportunities including battery storage elements and snow-removal under practical conditions are described.

  8. System and method of operating toroidal magnetic confinement devices

    Science.gov (United States)

    Chance, M.S.; Jardin, S.C.; Stix, T.H.; Grimm, R.C.; Manickam, J.; Okabayashi, M.

    1984-08-30

    This invention pertains to methods and arrangements for attaining high beta values in plasma confinement devices. More specifically, this invention pertains to methods for accessing the second stability region of operation in toroidal magnetic confinement devices.

  9. Panel 3

    OpenAIRE

    Lin, Jizhen; Hafren, Lena; Kerschner, Joseph; Li, Jian-Dong; Brown, Steve; Zheng, Qing Y.; Preciado, Diego; Nakamura, Yoshihisa; Huang, Qiuhong; Zhang, Yan

    2017-01-01

    Objective. The objective is to perform a comprehensive review of the literature up to 2015 on the genetics and precision medicine relevant to otitis media. Data Sources. PubMed database of the National Library of Medicine. Review Methods. Two subpanels were formed comprising experts in the genetics and precision medicine of otitis media. Each of the panels reviewed the literature in their respective fields and wrote draft reviews. The reviews were shared with all panel members, and a merged d...

  10. Panel Session

    DEFF Research Database (Denmark)

    Bertelsen, Olav Wedege

    2004-01-01

    In this panel session, four researchers will discuss the role of a theoretical foundation, in particular AT, in the design of information technology based artefacts. The general discussion will take of from a specific examination of the ActAD approach.......In this panel session, four researchers will discuss the role of a theoretical foundation, in particular AT, in the design of information technology based artefacts. The general discussion will take of from a specific examination of the ActAD approach....

  11. Cryogenic system for the Large Helical Device. The helium refrigerator/liquefier for Large Helical Device

    International Nuclear Information System (INIS)

    Maekawa, Ryuji; Mito, Toshiyuki; Satoh, Sadao

    1997-01-01

    A large-scale helium refrigerator/liquefier has been developed to provide reliable and safe operation for the Large Helical Device (LHD). The refrigerator is required to satisfy four different types of cooling methods: forced-flow supercritical helium, a pool boiling method, two-phase helium flow and forced-flow low-temperature (40-80 K) helium gas. The forced-flow supercritical helium is widely used in modern large-scale superconducting magnets. This method requires a much more complex refrigeration system than does pool boiling because of the circulation of low-temperature helium within a very long cooling path. The overall refrigeration system is fairly complicated because of these multi-refrigeration requirements. As a matter of fact, it is not likely to find this type of refrigeration plant in the world. The helium refrigerator has a total refrigeration capacity of 5.65 kW at 4.4 K and 20.6 kW at 80 K and 650 l/h liquefaction. The refrigerator was designed to have high processing efficiency since the construction expense is much less than the operating cost. In order to achieve this, the refrigerator has two precooling cycles (300 to 80 K and 80 to 20 K) and has two turboexpanders running in parallel with different temperature levels at the cold end. To achieve a high mass flow rate in a low-temperature regime, eight screw-type compressors are operated at room temperature. There are two compressor groups, group A and group B, to reduce the overall work load. Each group consists of 1st and 2nd stage compression processes. The total mass flow rate becomes 960 g/s at 1.864 MPa. This article reviews the basic characteristics of a 10 kW class helium refrigerator/liquefier and a simple refrigeration cycle. (author)

  12. System for characterizing semiconductor materials and photovoltaic devices through calibration

    Science.gov (United States)

    Sopori, B.L.; Allen, L.C.; Marshall, C.; Murphy, R.C.; Marshall, T.

    1998-05-26

    A method and apparatus are disclosed for measuring characteristics of a piece of material, typically semiconductor materials including photovoltaic devices. The characteristics may include dislocation defect density, grain boundaries, reflectance, external LBIC, internal LBIC, and minority carrier diffusion length. The apparatus includes a light source, an integrating sphere, and a detector communicating with a computer. The measurement or calculation of the characteristics is calibrated to provide accurate, absolute values. The calibration is performed by substituting a standard sample for the piece of material, the sample having a known quantity of one or more of the relevant characteristics. The quantity measured by the system of the relevant characteristic is compared to the known quantity and a calibration constant is created thereby. 44 figs.

  13. Devices, systems, and methods for detecting nucleic acids using sedimentation

    Energy Technology Data Exchange (ETDEWEB)

    Koh, Chung-Yan; Schaff, Ulrich Y.; Sommer, Gregory J.

    2017-10-24

    Embodiments of the present invention are directed toward devices, systems, and method for conducting nucleic acid purification and quantification using sedimentation. In one example, a method includes generating complexes which bind to a plurality of beads in a fluid sample, individual ones of the complexes comprising a nucleic acid molecule such as DNA or RNA and a labeling agent. The plurality of beads including the complexes may be transported through a density media, wherein the density media has a density lower than a density of the beads and higher than a density of the fluid sample, and wherein the transporting occurs, at least in part, by sedimentation. Signal may be detected from the labeling agents of the complexes.

  14. Toxin activity assays, devices, methods and systems therefor

    Science.gov (United States)

    Koh, Chung-Yan; Schaff, Ulrich Y.; Sommer, Gregory Jon

    2016-04-05

    Embodiments of the present invention are directed toward devices, system and method for conducting toxin activity assay using sedimentation. The toxin activity assay may include generating complexes which bind to a plurality of beads in a fluid sample. The complexes may include a target toxin and a labeling agent, or may be generated due to presence of active target toxin and/or labeling agent designed to be incorporated into complexes responsive to the presence of target active toxin. The plurality of beads including the complexes may be transported through a density media, wherein the density media has a lower density than a density of the beads and higher than a density of the fluid sample, and wherein the transporting occurs, at least in part, by sedimentation. Signal may be detected from the labeling agents of the complexes.

  15. Disruptive Logic Architectures and Technologies From Device to System Level

    CERN Document Server

    Gaillardon, Pierre-Emmanuel; Clermidy, Fabien

    2012-01-01

    This book discusses the opportunities offered by disruptive technologies to overcome the economical and physical limits currently faced by the electronics industry. It provides a new methodology for the fast evaluation of an emerging technology from an architectural perspective and discusses the implications from simple circuits to complex architectures. Several technologies are discussed, ranging from 3-D integration of devices (Phase Change Memories, Monolithic 3-D, Vertical NanoWires-based transistors) to dense 2-D arrangements (Double-Gate Carbon Nanotubes, Sublithographic Nanowires, Lithographic Crossbar arrangements). Novel architectural organizations, as well as the associated tools, are presented in order to explore this freshly opened design space. Describes a novel architectural organization for future reconfigurable systems; Includes a complete benchmarking toolflow for emerging technologies; Generalizes the description of reconfigurable circuits in terms of hierarchical levels; Assesses disruptive...

  16. 77 FR 58579 - Certain Two-Way Global Satellite Communication Devices, System and Components Thereof...

    Science.gov (United States)

    2012-09-21

    ... Communication Devices, System and Components Thereof; Institution of Investigation Pursuant to 19 U.S.C. 1337... certain two-way global satellite communication devices, system and components thereof that infringe one or... within the United States after importation of certain two-way global satellite communication devices...

  17. Weapon and Sighting System Compatibility Assessment for Prototype Maxillofacial Protection Devices

    Science.gov (United States)

    2013-03-01

    Weapon and Sighting System Compatibility Assessment for Prototype Maxillofacial Protection Devices by Frank Morelli and William H. Harper...ARL-TR-6367 March 2013 Weapon and Sighting System Compatibility Assessment for Prototype Maxillofacial Protection Devices Frank Morelli...Compatibility Assessment for Prototype Maxillofacial Protection Devices 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S

  18. Main devices design of submarine oil-water separation system

    Science.gov (United States)

    Cai, Wen-Bin; Liu, Bo-Hong

    2017-11-01

    In the process of offshore oil production, in order to thoroughly separate oil from produced fluid, solve the environment problem caused by oily sewage, and improve the economic benefit of offshore drilling, from the perspective of new oil-water separation, a set of submarine oil-water separation devices were designed through adsorption and desorption mechanism of the polymer materials for crude oil in this paper. The paper introduces the basic structure of gas-solid separation device, periodic separation device and adsorption device, and proves the rationality and feasibility of this device.

  19. National Incident Management System (NIMS) Standards Review Panel Workshop Summary Report

    Energy Technology Data Exchange (ETDEWEB)

    Stenner, Robert D.; Kirk, Jennifer L.; Stanton, James R.; Shebell, Peter; Schwartz, Deborah S.; Judd, Kathleen S.; Gelston, Gariann M.

    2006-02-07

    The importance and need for full compliant implementation of NIMS nationwide was clearly demonstrated during the Hurricane Katrina event, which was clearly expressed in Secretary Chertoff's October 4, 2005 letter addressed to the State's governors. It states, ''Hurricane Katrina was a stark reminder of how critical it is for our nation to approach incident management in a coordinated, consistent, and efficient manner. We must be able to come together, at all levels of government, to prevent, prepare for, respond to, and recover from any emergency or disaster. Our operations must be seamless and based on common incident management doctrine, because the challenges we face as a nation are far greater than capabilities of any one jurisdiction.'' The NIMS is a system/architecture for organizing response on a ''national'' level. It incorporations ICS as a main component of that structure (i.e., it institutionalizes ICS in NIMS). In a paper published on the NIMS Website, the following statements were made: ''NIMS represents a core set of doctrine, principles, terminology, and organizational processes to enable effective, efficient and collaborative incident management at all levels. To provide the framework for interoperability and compatibility, the NIMS is based on a balance between flexibility and standardization.'' Thus the NIC is challenged with the need to adopt quality SDO generated standards to support NIMS compliance, but in doing so maintain the flexibility necessary so that response operations can be tailored for the specific jurisdictional and geographical needs across the nation. In support of this large and complex challenge facing the NIC, the Pacific Northwest National Laboratory (PNNL) was asked to provide technical support to the NIC, through their DHS Science and Technology ? Standards Portfolio Contract, to help identify, review, and develop key standards for NIMS compliance. Upon

  20. Microprocessor system for data acquisition and processing for the Flora device

    International Nuclear Information System (INIS)

    Klimov, V.M.

    1986-01-01

    ''VEhFORMIKA'' microprocessor system for data collection and processing when conducting experiments at the ''Flora'' device is described, its application is grounded. The complex allows one to conduct investigations using multichannel methods and exercise the device electrophysical control

  1. Democracy and environmental quality in Latin America : a panel system of equations approach, 1995-2008

    OpenAIRE

    García Callejas, Danny

    2010-01-01

    Esta investigación sugiere que un incremento del 10% en los niveles de democracia en América Latina reduce hasta en 0.6% el nivel de emisiones per capita de CO2 (calidad ambiental). Esta relación se estima mediante un sistema de ecuaciones de panel de datos aplicado a 19 países latinoamericanos en el periodo 1995-2008. La democracia actúa como un medio para las crecientes demandas de calidad ambiental en América Latina causadas por el incremento en la población urbana y niveles de desarrollo....

  2. MPPT algorithm test on a photovoltaic emulating system constructed by a DC power supply and an indoor solar panel

    International Nuclear Information System (INIS)

    Zhou, Z.; Holland, P.M.; Igic, P.

    2014-01-01

    Highlights: • A novel PV emulator is constructed by using conventional solar panels with a DC power supply. • The proposed PV emulator is cost-effectiveness, relatively easy implementation. • The proposed PV emulator avoids the bandwidth problem associated with electronics PV emulators. • Indoor testing of MPPT algorithms and power converters avoids the dependency on solar irradiation. • The PV emulating system has been used for testing a P and O MPPT algorithm and a boost dc converter. - Abstract: In this paper a novel photovoltaic (PV) emulating scheme for testing maximum power point tracking (MPPT) algorithms and PV inverters has been proposed. It is constructed by the parallel connection of conventional solar panels with a DC power supply operating in current source mode. The advantages of the proposed scheme are cost-effectiveness, relatively easy implementation and indoor testing of MPPT algorithms and power converters avoiding weather and time of day dependency on solar irradiation levels. Furthermore, the proposed PV emulator avoids the bandwidth problem associated with the dc converter based PV emulating systems. Detailed circuit connection, parameters, electrical characteristics and mathematical model of the PV emulator are presented and discussed. Proposed PV emulating system has been used to test a boost DC/DC converter controlled by Perturb and Observe (P and O) MPPT algorithm. Test results confirmed the effectiveness of the proposed PV emulation system and all achieved results correspond well to the original designed values

  3. Electronic security systems and active implantable medical devices.

    Science.gov (United States)

    Irnich, Werner

    2002-08-01

    How do active implantable medical devices react in the presence of strong magnetic fields in the frequency range between extremely low frequency (ELF) to radiofrequency (RF) as they are emitted by electronic security systems (ESS)? There are three different sorts of ESSs: electronic article surveillance (EAS) devices, metal detector (MDS) devices, and radiofrequency identification (RFID) systems. Common to all is the production of magnetic fields. There is an abundance of literature concerning interference by ESS gates with respect to if there is an influence possible and if such an influence can bear a risk for the AIMD wearers. However, there has been no attempt to study the physical mechanism nor to develop a model of how and under which conditions magnetic fields can influence pacemakers and defibrillators and how they could be disarmed by technological means. It is too often assumed that interference of AIMD with ESS is inevitable. Exogenous signals of similar intensity and rhythm to heart signals can be misinterpreted and, thus, confuse the implant. Important for the interference coupling mechanism is the differentiation between a "unipolar" and a "bipolar" system. With respect to magnetic fields, the left side implanted pacemaker is the most unfavorable case as the lead forms approximately a semicircular area of maximum 225 cm2 into which a voltage can be induced. This assumption yields an interference coupling model that can be expressed by simple mathematics. The worst-case conditions for induced interference voltages are a coupling area of 225 cm2 that is representative for a large human, a homogeneous magnetic field perpendicular to the area formed by the lead, and a unipolar ventricular pacemaker system that is implanted on the left side of the thorax and has the highest interference sensitivity. In bipolar systems the fields must be 17 times larger when compared to a unipolar system to have the same effect. The magnetic field for interfering with ICDs

  4. Alignment and focusing device for a multibeam laser system

    International Nuclear Information System (INIS)

    Sweatt, W.C.

    1980-01-01

    Large inertial confinement fusion laser systems have many beams focusing on a small target. The Antares system is a 24-beam CO 2 pulse laser. To produce uniform illumination, the 24 beams must be individually focused on (or near) the target's surface in a symmetric pattern. To assess the quality of a given beam, we will locate a Smartt (point diffraction) interferometer at the desired focal point and illuminate it with an alignment laser. The resulting fringe pattern shows defocus, lateral misalignment, and beam aberrations; all of which can be minimized by tilting and translating the focusing mirror and the preceding flat mirror. The device described in this paper will remotely translate the Smartt interferometer to any position in the target space and point it in any direction using a two-axis gimbal. The fringes produced by the interferometer are relayed out of the target vacuum shell to a vidicon by a train or prisms. We are designing four separate snap-in heads to mount on the gimbal; two of which are Smartt interferometers (for 10.6 μm and 633 nm) and two for pinholes, should we wish to put an alignment beam backwards through the system

  5. A Mobile Device System for Early Warning of ECG Anomalies

    Directory of Open Access Journals (Sweden)

    Adam Szczepański

    2014-06-01

    Full Text Available With the rapid increase in computational power of mobile devices the amount of ambient intelligence-based smart environment systems has increased greatly in recent years. A proposition of such a solution is described in this paper, namely real time monitoring of an electrocardiogram (ECG signal during everyday activities for identification of life threatening situations. The paper, being both research and review, describes previous work of the authors, current state of the art in the context of the authors’ work and the proposed aforementioned system. Although parts of the solution were described in earlier publications of the authors, the whole concept is presented completely for the first time along with the prototype implementation on mobile device—a Windows 8 tablet with Modern UI. The system has three main purposes. The first goal is the detection of sudden rapid cardiac malfunctions and informing the people in the patient’s surroundings, family and friends and the nearest emergency station about the deteriorating health of the monitored person. The second goal is a monitoring of ECG signals under non-clinical conditions to detect anomalies that are typically not found during diagnostic tests. The third goal is to register and analyze repeatable, long-term disturbances in the regular signal and finding their patterns.

  6. SUBWAY POWER SYSTEMS WITH MODERN SEMICONDUCTOR CONVERTERS AND ENERGY STORAGE DEVICES

    Directory of Open Access Journals (Sweden)

    O.I. Kholod

    2013-02-01

    Full Text Available Five subway power systems, a traditional power system and power systems with an active rectifier and an energy storage device, are considered. Estimation of energy loss in the analyzed subway power systems circuits is made.

  7. Nickel allergy induced systemic reaction to an intracardiac amplatzer device.

    Science.gov (United States)

    Prestipino, Filippo; Pragliola, Claudio; Lusini, Mario; Chello, Massimo

    2014-05-01

    Nickel hypersensitivity is reported in about 10-15% of the general population and manifests mainly with dermatological signs. Chest discomfort, palpitations, signs and symptoms of pericarditis, and migraine are symptoms reported in rare cases of nickel hypersensitivity after implantation of a cardiac device made of nickel. We present the case of a patient with a nickel allergy from an Amplatzer device in which the removal of the device produced resolution of the symptoms. © 2014 Wiley Periodicals, Inc.

  8. A foundation for the future: building an environmental monitoring system for the oil sands[Report of the federal advisory panel on oilsands monitoring

    Energy Technology Data Exchange (ETDEWEB)

    Dowdeswell, L.; Dillon, P.; Ghoshal, S.; Miall, A.; Rasmussen, J.; Smol, J.P.

    2010-12-15

    In September, 2010, important concerns regarding the impacts of oil sand industry on the environment in the Lower Athabasca River Basin resulted in the creation of the oil sands advisory panel. This panel was set up to examine and evaluate the existing system for research and monitoring and identify strengths and weaknesses regarding water monitoring in the Lower Athabasca River Basin and connected waterways. In this report, the panel provides important elements to guide the monitoring of water quality and quantity. The panel has identified several organizations or individuals contributing to the research and monitoring of the Athabasca River system but also points out in the document that the research has not yet led to a consensus regarding the impacts of oil sands development on the environment. It has also been observed that no standardized data management system has been put in place to facilitate the access to data for interested parties. Important weaknesses in the existing monitoring system were identified by the panel. The advisory panel recommended the implementation of a credible and transparent, comprehensive and adaptive monitoring program, through a collaborative work between relevant jurisdictions and stakeholders. 50 refs.

  9. Automatic Data Logging and Quality Analysis System for Mobile Devices

    Directory of Open Access Journals (Sweden)

    Yong-Yi Fanjiang

    2017-01-01

    Full Text Available The testing phase of mobile device products includes two important test projects that must be completed before shipment: the field trial and the beta user trial. During the field trial, the product is certified based on its integration and stability with the local operator’s system, and, during the beta user trial, the product is certified by multiple users regarding its daily use, where the goal is to detect and solve early problems. In the traditional approach used to issue returns, testers must log into a web site, fill out a problem form, and then go through a browser or FTP to upload logs; however, this is inconvenient, and problems are reported slowly. Therefore, we propose an “automatic logging analysis system” (ALAS to construct a convenient test environment and, using a record analysis (log parser program, automate the parsing of log files and have questions automatically sent to the database by the system. Finally, the mean time between failures (MTBF is used to establish measurement indicators for the beta user trial.

  10. Communication Between Devices in the Viola Document Delivery System

    Directory of Open Access Journals (Sweden)

    Theodor Tolstoy

    2015-01-01

    Full Text Available Viola is a newly developed document delivery system that handles incoming and outgoing requests for printed books, articles, sharing electronic resources, and other document delivery services on the local level in a library organisation. An important part of Viola is the stack fetching Android application that enables librarians to collect books in the open and closed stacks in an efficient manner using a smartphone and a Bluetooth connected portable printer. The aim of this article is to show how information is transferred between systems and devices in Viola. The article presents code examples from Viola that use current .NET technologies. The examples span from the creation of high-level REST-based JSON APIs to byte array communication with a Bluetooth connected printer and the reading of RFID tags. Please note that code examples in this article are for illustration purposes only. Null checking and other exception handling has been removed for clarity. Code that is separated in Viola for testability and other reasons has been brought together to make it more readable.

  11. Integrated isolators for opto-electro-mechanical systems and devices

    Science.gov (United States)

    Cruz Rivera, Luis J.; Pandit, Saurabh; Pieski, Suzanne; Cobian, Ryan; Cherif, Monher; Stadler, Bethanie J. H.

    2001-05-01

    The development of integrated isolators is critical to the functional integration of optics within OEM devices and systems. Bulk isolators have proven to be the most important components in many fiber optic systems due to their ability to protect light sources from back-reflected light. Such reflections are created at each component interface, inhomogeneity, or other perturbation in the path of the light. This paper reviews the operation of and current work in integrated isolators. Several methods for fabricating monolithically integrated magneto-optical isolators are discussed, including the fabrication of garnets, magnets, and cladding/buffer layers. Garnets are traditionally grown by liquid phase epitaxy (LPE) at temperatures and environments that are not friendly to semiconductors or other common substrates. More importantly, LPE requires epitaxial growth, which dictates garnet substrates and therefore hybrid integration techniques. We have used metallorganic chemical vapor deposition (MOCVD), sputtering, and metallorganic chemical liquid deposition (MOCLD) to deposit single-phase yttrium iron garnet (YIG). A variety of substrates were used, including MgO and SiO2 which are promising buffer layer materials. The chemical, structural, and optical properties of the resulting films are discussed. We have also used a variety of sputtering techniques to integrate permanent magnet films with semiconductor processing. These magnets are sufficient for biasing the magneto-optical element. The chemical, structural and magnetic properties of these materials, as well as total integration will be discussed.

  12. EPICS device support module as ATCA system manager for the ITER fast plant system controller

    Energy Technology Data Exchange (ETDEWEB)

    Carvalho, Paulo F., E-mail: pricardofc@ipfn.ist.utl.pt [Associação EURATOM/IST, Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico – Universidade Técnica de Lisboa, Lisboa (Portugal); Santos, Bruno; Gonçalves, Bruno; Carvalho, Bernardo B.; Sousa, Jorge; Rodrigues, A.P.; Batista, António J.N.; Correia, Miguel; Combo, Álvaro [Associação EURATOM/IST, Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico – Universidade Técnica de Lisboa, Lisboa (Portugal); Correia, Carlos M.B.A. [Centro de Instrumentação, Departamento de Física, Universidade de Coimbra, Coimbra (Portugal); Varandas, Carlos A.F. [Associação EURATOM/IST, Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico – Universidade Técnica de Lisboa, Lisboa (Portugal)

    2013-10-15

    Highlights: ► In Nuclear Fusion, demanding security and high-availability requirements call for redundancy to be available. ► ATCA based Nuclear Fusion Systems are composed by several electronic and mechanical component. ► Control and monitoring of ATCA electronic systems are recommended. ► ITER Fast Plant System Controller Project CODAC system prototype. ► EPICS device support module as External ATCA system manager solution. -- Abstract: This paper presents an Enhanced Physics and Industrial Control System (EPICS) device support module for the International Thermonuclear Experimental Reactor (ITER) Fast Plant System Controller (FPSC) project based in Advanced Telecommunications Computing Architecture (ATCA) specification. The developed EPICS device support module provides an External System Manager (ESM) solution for monitoring and control the ITER FPSC ATCA shelf system and data acquisition boards in order to take proper action and report problems to a control room operator or high level management unit in case of any system failure occurrence. EPICS device support module acts as a Channel Access (CA) server to report problems and publish ATCA system data information to the control room operator, high level management unit or other CA network clients such as Control System Studio Operator Interfaces (CSS OPIs), Best Ever Alarm System Toolkit (BEAST), Best Ever Archive Utility (BEAUTY) or other CA client applications. EPICS device support module communicates with the ATCA Shelf manager (ShM) using HTTP protocol to send and receive commands through POST method in order to get and set system and shelf components properties such as fan speeds measurements, temperatures readings, module status and ATCA boards acquisition and configuration parameters. All system properties, states, commands and parameters are available through the EPICS device support module CA server in EPICS Process Variables (PV) and signals format. ATCA ShM receives the HTTP protocol

  13. Lithographically-Scribed Planar Holographic Optical CDMA Devices and Systems

    National Research Council Canada - National Science Library

    Mossberg, Thomas

    2007-01-01

    .... Holographic Bragg Reflectors (HBRs) comprise an exemplary lithographically scribed fully integrated holographic device useful for multiplexing of wavelength differentiated optical signals and general purpose spectral filtering...

  14. Evaluation of Test Antifouling (AF) and Foul Release Coating Systems on Bilge Keel Panels and Ship Hulls

    National Research Council Canada - National Science Library

    Radakovich, Thomas

    2004-01-01

    .... Evaluation consisted of two phases, bilge keel panel testing and hull patch testing. Four ships served as test platforms for bilge keel panel testing; USS FOSTER (DD 980). USS THOMAS GATES (CG 51), USS LEYTE GULF (CG 55...

  15. Reengineering a PC-based System into the Mobile Device Product Line

    DEFF Research Database (Denmark)

    Zhang, Weishan; Jarzabek, Stanislaw; Loughran, Neil

    2003-01-01

    There is a growing demand to port existing PC-based software systems to mobile device platforms. Systems running on mobile devices share basic characteristics with their PC-based counterparts, but differ from them in details of user interfaces, application models, etc. Systems running on mobile...... devices must also perform well using less memory than PC-based systems. Mobile devices themselves are different from each other in many ways, too. We describe how we made an existing PC-based City Guide System available on a wide range of mobile devices, in a cost-effective way. We applied "reengineering...... into a product line architecture" approach to achieve the goal. Our product line architecture facilitates reuse via generation. We generate specific City Guide Systems for target platforms including PC, Pocket PC and other mobile devices, from generic meta-components that form the City Guide System product line...

  16. Detecting delaminations and disbondings on full-scale wing composite panel by guided waves based SHM system

    Science.gov (United States)

    Monaco, E.; Boffa, N. D.; Memmolo, V.; Ricci, F.; Maio, L.

    2016-04-01

    A full-scale lower wing panel made of composite material has been designed, manufactured and sensorised within the European Funded research project named SARISTU. The authors contributed to the whole development of the system, from design to implementation as well as to the impacts campaign phase where Barely Visible and Visible Damages (BVID and VID) are to be artificially induced on the panel by a pneumatic impact machine. This work summarise part of the experimental results related to damages production, their assessment by C-SCAN as reference NDT method as well as damage detection of delimitations by a guided waves based SHM. The SHM system is made by customized piezoelectric patches secondary bonded on the wing plate acting both as guided waves sources and receivers. The paper will deal mostly with the experimental impact campaign and the signal analyses carried out to extract the metrics more sensitive to damages induced. Image reconstruction of the damages dimensions and shapes will be also described based mostly on the combination of metrics maps over the plate partial surfaces. Finally a comparison of damages maps obtained by the SHM approach and those obtained by "classic" C-SCAN will be presented analyzing briefly pros and cons of the two different approached as a combination to the most effective structural maintenance scenario of a commercial aircraft.

  17. MYRRHA/XT-ADS primary system design and experimental devices

    International Nuclear Information System (INIS)

    Maes, D.

    2009-01-01

    The EUROTRANS project is an integrated project in the Sixth European Framework Program in the context of Partitioning and Transmutation. The objective of this project is to work towards an ETD (European Transmutation Demonstration) in a step-wise manner. The first step is to carry out an advanced design of a small-scale XT-ADS (eXperimental Transmutation in an Accelerator Driven System) for realisation in a short-term (about 10 years) as well as to accomplish a generic conceptual design of EFIT (European Facility for Industrial Transmutation) for realisation in the long-term. The MYRRHA-2005 design served as a starting basis for the XT-ADS. Many options have been revisited and the framework is now set up. While the MYRRHA-2005 design was still a conceptual design, the intention is to get at the end of the EUROTRANS project (March 2009) an advanced design of the XT-ADS, albeit a first advanced design. While the design work performed during the first years of the project (2005-2006) was mainly devoted to optimise and enhance the primary and secondary system configuration according to the suggestions and contributions of our industrial partners (Ansaldo Nucleare, Areva, Suez-Tractebel) within the DM1 (Domain 1 D ESIGN ) , the last year work objectives mainly consisted of (1) the release of the Remote Handling Design Catalogue for XT-ADS and (2) the formulation of the specification of the experimental devices according to the XT-ADS objectives and adapted to the actual XT-ADS core and core support structure design; (3) the detailed calculations of the main XT-ADS primary and secondary system components

  18. Processes in construction of failure management expert systems from device design information

    Science.gov (United States)

    Malin, Jane T.; Lance, Nick

    1987-01-01

    This paper analyzes the tasks and problem solving methods used by an engineer in constructing a failure management expert system from design information about the device to te diagnosed. An expert test engineer developed a trouble-shooting expert system based on device design information and experience with similar devices, rather than on specific expert knowledge gained from operating the device or troubleshooting its failures. The construction of the expert system was intensively observed and analyzed. This paper characterizes the knowledge, tasks, methods, and design decisions involved in constructing this type of expert system, and makes recommendations concerning tools for aiding and automating construction of such systems.

  19. 75 FR 68200 - Medical Devices; Radiology Devices; Reclassification of Full-Field Digital Mammography System

    Science.gov (United States)

    2010-11-05

    ... for Breast- Cancer Screening,'' New England Journal of Medicine, 353: 1773-1783, 2005. 3. Yaffe, M., A..., 10903 New Hampshire Ave., Bldg. 66, rm. G304, Silver Spring, MD 20993-0002, 301-796-6887; or Kyle J. Myers, Center for Devices and Radiological Health, Food and Drug Administration, 10903 New Hampshire Ave...

  20. Testing of MEMS/MOEMS/MNT devices and systems

    Science.gov (United States)

    van Heeren, Henne; El-Fatatry, Ayman; Paschalidou, Lia; Salomon, Patric R.

    2005-01-01

    Unlike electronic devices, where for analysis only electrical parameters need to be tested, Micro and Nano Technology (MNT) devices require precise measurement of multi domain parameters for characterization. Furthermore, the sensitivities require other or improved technologies. For instance, for testing a MEMS device, a stable supply of physical energy is required and must be transferred to the product in a reproducible way. Also a sensitive measuring technology is necessary to detect the electrical signal produced as a response to the physical energy on the device. Sometimes interactions between input and output make measuring difficult. A third point is that handling of the devices is difficult due to their non-standard sizes and small dimension. Also MST including MEMS and MOEMS devices require new types of reliability testing addressing stiction, and other specific failure modes. Thus, the testing of MNT devices is much more complex than standard electronic components. Currently standardized tests are often not available, neither is there sufficient background information available about MNT testing, as most of the companies regard testing experience, and especially product testing, as company confidential information. However, the MNT industry can utilise existing testing equipment. This article addresses the available equipment for MNT testing in relation to the industry needs. Examples of the instruments discussed include optical profilers for dynamic measurement of MOEMS/MEMS devices, such as gyros and accelerometers, and wafer testers for optical products.

  1. Hepatitis Panel

    Science.gov (United States)

    ... others, the virus can cause long-term, chronic liver disease . Hepatitis C is most often spread by contact with infected ... contact with an infected person. Many people with hepatitis C develop chronic liver disease and cirrhosis . A hepatitis panel includes tests for ...

  2. Effective vulnerability assessments for physical security devices, systems, and programs

    International Nuclear Information System (INIS)

    Johnston, R.G.; Garcia, A.R.E.

    2002-01-01

    Full text: The efficacy of devices, systems, and programs used for physical security depend critically on having periodic and effective vulnerability assessments. Effective vulnerability assessments, in turn, require certain conditions and attributes. These include: a proper understanding of their purpose; not confusing vulnerability assessments with other kinds of metrics, analyses, tests, and security exercises; the view that vulnerabilities are inevitable, and that finding them is good news (since they can then be mitigated), not bad news; rejection of findings of no vulnerabilities; avoidance of mere 'compliance mode' rubber stamping; the use of the proper outside, independent, imaginative personnel; psychologically predisposed to finding and demonstrating problems; the absence of conflicts of interest; no unrealistic constraints on the possible attack tools, procedures, personnel, or strategies; efforts to not just find and demonstrate vulnerabilities, but also to suggest possible countermeasures; proper context; input and buy-in from ALL facility security personnel, especially low-level personnel; emphasis on the simplest, most relevant attacks first; no underestimation of potential adversaries; consideration of fault analysis attacks; awareness of Rohrbach's Maxim and Shannon's Maxim. In addition to these factors, we will cover some of the complex issues and problems associated with the design of vulnerability assessments. There will also be suggestions on how to conduct effective vulnerability assessments on a severely limited budget. We will conclude with a discussion of both conventional and unconventional ways of reporting results. (author)

  3. A Model for Service Life Control of Selected Device Systems

    Directory of Open Access Journals (Sweden)

    Zieja Mariusz

    2014-04-01

    Full Text Available This paper presents a way of determining distribution of limit state exceedence time by a diagnostic parameter which determines accuracy of maintaining zero state. For calculations it was assumed that the diagnostic parameter is deviation from nominal value (zero state. Change of deviation value occurs as a result of destructive processes which occur during service. For estimation of deviation increasing rate in probabilistic sense, was used a difference equation from which, after transformation, Fokker-Planck differential equation was obtained [4, 11]. A particular solution of the equation is deviation increasing rate density function which was used for determining exceedance probability of limit state. The so-determined probability was then used to determine density function of limit state exceedance time, by increasing deviation. Having at disposal the density function of limit state exceedance time one determined service life of a system of maladjustment. In the end, a numerical example based on operational data of selected aircraft [weapon] sights was presented. The elaborated method can be also applied to determining residual life of shipboard devices whose technical state is determined on the basis of analysis of values of diagnostic parameters.

  4. 21 CFR 801.60 - Principal display panel.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Principal display panel. 801.60 Section 801.60... panel. The term principal display panel, as it applies to over-the-counter devices in package form and..., or examined under customary conditions of display for retail sale. The principal display panel shall...

  5. Thermal Analysis of Solar Panels

    Science.gov (United States)

    Barth, Nicolas; de Correia, João Pedro Magalhães; Ahzi, Saïd; Khaleel, Mohammad Ahmed

    In this work, we propose to analyze the thermal behavior of PV panels using finite element simulations (FEM). We applied this analysis to compute the temperature distribution in a PV panel BP 350 subjected to different atmospheric conditions. This analysis takes into account existing formulations in the literature and, based on NOCT conditions, meteorological data was used to validate our approach for different wind speed and solar irradiance. The electrical performance of the PV panel was also studied. The proposed 2D FEM analysis is applied to different region's climates and was also used to consider the role of thermal inertia on the optimization of the PV device efficiency.

  6. [Study on the reform and improvement of the medical device registration system in China].

    Science.gov (United States)

    Wang, Lanming

    2012-11-01

    Based on the theories of the Government Regulation and Administrative Licensure, aiming at the current situations of medical device registration system in China, some policy suggestions for future reform and improvement were provided as follows. (1) change the concepts of medical device registration administration. (2) perfect the regulations of medical device registration administration. (3) reform the medical device review organizational system. (4) Optimize the procedure of review and approval. (5) set up and maintain a professional team of review and approval staff. (6) reinforce the post-marketing supervision of medical devices. (7) foster and bring into play of the role of non-government organizations.

  7. Enabling Dynamic Security Management of Networked Systems via Device-Embedded Security (Self-Securing Devices)

    Science.gov (United States)

    2007-01-15

    device. However, with rapidly shrinking hardware costs, growing software development costs, and astronomical security costs, it makes no sense to not be...ceptable levels of performance and manageability. After describing our inspiration for this architecture ( medieval siege warfare), this chapter overviews...perimeters. Borrowing from lessons learned in pre-gun warfare, we pro- pose a new network security architecture analogous to medieval defense

  8. 20-kW solar photovoltaic flat-panel power system for an uninterruptible power-system load in El Paso, Texas. Phase II. System fabrication. Final report October 1, 1979-May 31, 1981

    Energy Technology Data Exchange (ETDEWEB)

    Risser, V.V.

    1981-12-01

    The system plans, construction, integration and test, and performance evaluation are discussed for the photovoltaic power supply at the Newman Power Station in El Paso, Texas. The system consists of 64 parallel-connected panels, each panel containing nine series-connected photovoltaic modules. The system is connected, through power monitoring equipment, to an existing DC bus that supplies uninterruptible power to a computer that controls the power generating equipment. The site is described and possible environmental hazards are assessed. Site preparation and the installation of the photovoltaic panels, electrical cabling, and instrumentation subsystems are described. System testing includes initial system checkout, module performance test, control system test. A training program for operators and maintenance personnel is briefly described, including visual aids. Performance data collection and analysis are described, and actual data are compared with a computer simulation. System drawings are included. (LEW)

  9. Panel summary of cyber-physical systems (CPS) and Internet of Things (IoT) opportunities with information fusion

    Science.gov (United States)

    Blasch, Erik; Kadar, Ivan; Grewe, Lynne L.; Brooks, Richard; Yu, Wei; Kwasinski, Andres; Thomopoulos, Stelios; Salerno, John; Qi, Hairong

    2017-05-01

    During the 2016 SPIE DSS conference, nine panelists were invited to highlight the trends and opportunities in cyber-physical systems (CPS) and Internet of Things (IoT) with information fusion. The world will be ubiquitously outfitted with many sensors to support our daily living thorough the Internet of Things (IoT), manage infrastructure developments with cyber-physical systems (CPS), as well as provide communication through networked information fusion technology over the internet (NIFTI). This paper summarizes the panel discussions on opportunities of information fusion to the growing trends in CPS and IoT. The summary includes the concepts and areas where information supports these CPS/IoT which includes situation awareness, transportation, and smart grids.

  10. Reconfigurable Computing for Embedded Systems, FPGA Devices and Software Components

    National Research Council Canada - National Science Library

    Bardouleau, Graham; Kulp, James

    2005-01-01

    In recent years the size and capabilities of field-programmable gate array (FPGA) devices have increased to a point where they can be deployed as adjunct processing elements within a multicomputer environment...

  11. System requirements for one-time-use ENRAF control panel software

    International Nuclear Information System (INIS)

    HUBER, J.H.

    1999-01-01

    An Enraf Densitometer is installed on tank 241-AY-102. The Densitometer will frequently be tasked to obtain and log density profiles. The activity can be effected a number of ways. Enraf Incorporated provides a software package called ''Logger18'' to its customers for the purpose of in-shop testing of their gauges. Logger18 is capable of accepting an input file which can direct the gauge to obtain a density profile for a given tank level and bottom limit. Logger18 is a complex, DOS based program which will require trained technicians and/or tank farm entries to obtain the data. ALARA considerations have prompted the development of a more user-friendly, computer-based interface to the Enraf densitometers. This document records the plan by which this new Enraf data acquisition software will be developed, reviewed, verified, and released. This plan applies to the development and implementation of a one-time-use software program, which will be called ''Enraf Control Panel.'' The software will be primarily used for remote operation of Enraf Densitometers for the purpose of obtaining and logging tank product density profiles

  12. System requirements for one-time-use ENRAF control panel software

    Energy Technology Data Exchange (ETDEWEB)

    HUBER, J.H.

    1999-08-19

    An Enraf Densitometer is installed on tank 241-AY-102. The Densitometer will frequently be tasked to obtain and log density profiles. The activity can be effected a number of ways. Enraf Incorporated provides a software package called ''Logger18'' to its customers for the purpose of in-shop testing of their gauges. Logger18 is capable of accepting an input file which can direct the gauge to obtain a density profile for a given tank level and bottom limit. Logger18 is a complex, DOS based program which will require trained technicians and/or tank farm entries to obtain the data. ALARA considerations have prompted the development of a more user-friendly, computer-based interface to the Enraf densitometers. This document records the plan by which this new Enraf data acquisition software will be developed, reviewed, verified, and released. This plan applies to the development and implementation of a one-time-use software program, which will be called ''Enraf Control Panel.'' The software will be primarily used for remote operation of Enraf Densitometers for the purpose of obtaining and logging tank product density profiles.

  13. Guest Editorial Advanced Distributed Control of Energy Conversion Devices and Systems

    DEFF Research Database (Denmark)

    Davoudi, Ali; Guerrero, Josep M.; Lewis, Frank

    2014-01-01

    The papers in this special issue on advanced distributed control of energy conversion devices and systems are loosely grouped into three categories: 1) ac energy conversion systems; 2) dc energy conversion systems; and 3) optimization and standards.......The papers in this special issue on advanced distributed control of energy conversion devices and systems are loosely grouped into three categories: 1) ac energy conversion systems; 2) dc energy conversion systems; and 3) optimization and standards....

  14. Integrated control rod monitoring device

    International Nuclear Information System (INIS)

    Saito, Katsuhiro

    1997-01-01

    The present invention provides a device in which an entire control rod driving time measuring device and a control rod position support device in a reactor building and a central control chamber are integrated systematically to save hardwares such as a signal input/output device and signal cables between boards. Namely, (1) functions of the entire control rod driving time measuring device for monitoring control rods which control the reactor power and a control rod position indication device are integrated into one identical system. Then, the entire devices can be made compact by the integration of the functions. (2) The functions of the entire control rod driving time measuring device and the control rod position indication device are integrated in a central operation board and a board in the site. Then, the place for the installation of them can be used in common in any of the cases. (3) The functions of the entire control rod driving time measuring device and the control rod position indication device are integrated to one identical system to save hardware to be used. Then, signal input/output devices and drift branching panel boards in the site and the central operation board can be saved, and cables for connecting both of the boards is no more necessary. (I.S.)

  15. Radiation sensitive devices and systems for detection of radioactive materials and related methods

    Science.gov (United States)

    Kotter, Dale K

    2014-12-02

    Radiation sensitive devices include a substrate comprising a radiation sensitive material and a plurality of resonance elements coupled to the substrate. Each resonance element is configured to resonate responsive to non-ionizing incident radiation. Systems for detecting radiation from a special nuclear material include a radiation sensitive device and a sensor located remotely from the radiation sensitive device and configured to measure an output signal from the radiation sensitive device. In such systems, the radiation sensitive device includes a radiation sensitive material and a plurality of resonance elements positioned on the radiation sensitive material. Methods for detecting a presence of a special nuclear material include positioning a radiation sensitive device in a location where special nuclear materials are to be detected and remotely interrogating the radiation sensitive device with a sensor.

  16. EFSA NDA Panel (EFSA Panel on Dietetic Products, Nutrition and Allergies), 2015. Scientific Opinion on the substantiation of a health claim related to vitamin D and contribution to the normal function of the immune system pursuant to Article 14 of Regulation (EC) No 1924/2006

    DEFF Research Database (Denmark)

    Tetens, Inge

    2015-01-01

    . The Panel had previously assessed a claim on vitamin D and contribution to the normal function of the immune system with a favourable outcome. The target population was the general population. The Panel considered that vitamin D plays a regulatory role in the functioning of the immune system. The Panel...... considers that the role of vitamin D in the functioning of the immune system applies to all ages, including children. The Panel concludes that a cause and effect relationship has been established between the dietary intake of vitamin D and contribution to the normal function of the immune system...... on the scientific substantiation of a health claim related to vitamin D and contribution to the normal function of the immune system. The Panel considers that vitamin D is sufficiently characterised. Contribution to the normal function of the immune system is a beneficial physiological effect for children...

  17. A moving image system for cardiovascular nuclear medicine. A dedicated auxiliary device for the total capacity imaging system for multiple plane dynamic colour display

    International Nuclear Information System (INIS)

    Iio, M.; Toyama, H.; Murata, H.; Takaoka, S.

    1981-01-01

    The recent device of the authors, the dedicated multiplane dynamic colour image display system for nuclear medicine, is discussed. This new device is a hardware-based auxiliary moving image system (AMIS) attached to the total capacity image processing system of the authors' department. The major purpose of this study is to develop the dedicated device so that cardiovascular nuclear medicine and other dynamic studies will include the ability to assess the real time delicate processing of the colour selection, edge detection, phased analysis, etc. The auxiliary system consists of the interface for image transferring, four IC refresh memories of 64x64 matrix with 10 bit count depth, a digital 20-in colour TV monitor, a control keyboard and a control panel with potentiometers. This system has five major functions for colour display: (1) A microcomputer board can select any one of 40 different colour tables preset in the colour transformation RAM. This key also provides edge detection at a certain level of the count by leaving the optional colour and setting the rest of the levels at 0 (black); (2) The arithmetic processing circuit performs the operation of the fundamental rules, permitting arithmetic processes of the two images; (3) The colour level control circuit is operated independently by four potentiometers for four refresh image memories, so that the gain and offset of the colour level can be manually and visually controlled to the satisfaction of the operator; (4) The simultaneous CRT display of the maximum four images with or without cinematic motion is possible; (5) The real time movie interval is also adjustable by hardware, and certain frames can be freezed with overlapping of the dynamic frames. Since this system of AMIS is linked with the whole capacity image processing system of the CPU size of 128kW, etc., clinical applications are not limited to cardiovascular nuclear medicine. (author)

  18. East to west – The optimal tilt angle and orientation of photovoltaic panels from an electricity system perspective

    International Nuclear Information System (INIS)

    Hartner, Michael; Ortner, André; Hiesl, Albert; Haas, Reinhard

    2015-01-01

    Highlights: • Adjustments of PV installation angles can reduce total electricity generation costs. • However total benefits are small (<1% of total costs) even for high PV shares. • In Austria and Germany adjustments toward east and steeper tilt can be beneficial. • PV market values drop significantly with high PV shares also for adjusted angles. • Also CO 2 reductions decrease but are still high even for a doubling of PV capacity. - Abstract: The integration of photovoltaic as a fluctuating renewable energy source has raised concerns about additional costs for the electricity system due to the variable nature of power output leading to more frequent and steeper ramping of conventional power plants and the need for backup capacity. One way to reduce those costs can be the variation of installation angles of PV panels at different locations to smoothen out the total production from PV in the whole system. To a certain extent steeper tilt angles can shift the production from summer months to winter months and the variation of the azimuth from east to west can partly shift production during the day increasing the production in morning or afternoon hours. However, for fixed mounted PV panels, there is one angle combination that maximizes the total output of the PV panel throughout the year and each deviation from this angle combination results in losses of total output. This paper evaluates the trade-off between annual energy losses and possible electricity generation cost reductions through adapting PV installation angles for the current electricity system and for potentially higher PV penetration levels in the future. A theoretical explanation why the annual maximum output of a PV system is not always the optimal solution from a system perspective is presented. To assess the effects of deviations from output maximizing angles at present, the wholesale market value of PV for various tilt angles and orientations in 23 regions of Austria and Germany using

  19. The inherent weaknesses in industrial control systems devices; hacking and defending SCADA systems

    Science.gov (United States)

    Bianco, Louis J.

    The North American Electric Reliability Corporation (NERC) is about to enforce their NERC Critical Infrastructure Protection (CIP) Version Five and Six requirements on July 1st 2016. The NERC CIP requirements are a set of cyber security standards designed to protect cyber assets essential the reliable operation of the electric grid. The new Version Five and Six requirements are a major revision to the Version Three (currently enforced) requirements. The new requirements also bring substations into scope alongside Energy Control Centers. When the Version Five requirements were originally drafted they were vague, causing in depth discussions throughout the industry. The ramifications of these requirements has made owners look at their systems in depth, questioning how much money it will take to meet these requirements. Some owners saw backing down from routable networks to non-routable as a means to save money as they would be held to less requirements within the standards. Some owners saw removing routable connections as a proper security move. The purpose of this research was to uncover the inherent weaknesses in Industrial Control Systems (ICS) devices; to show how ICS devices can be hacked and figure out potential protections for these Critical Infrastructure devices. In addition, this research also aimed to validate the decision to move from External Routable connectivity to Non-Routable connectivity, as a security measure and not as a means of savings. The results reveal in order to ultimately protect Industrial Control Systems they must be removed from the Internet and all bi-directional external routable connections must be removed. Furthermore; non-routable serial connections should be utilized, and these non-routable serial connections should be encrypted on different layers of the OSI model. The research concluded that most weaknesses in SCADA systems are due to the inherent weaknesses in ICS devices and because of these weaknesses, human intervention is

  20. Development of full scale testing of an alternate foundation system for post and panel retaining walls.

    Science.gov (United States)

    2009-03-01

    The alternate post system offers benefits such as ease of construction, reduced construction time, and : lower wall costs. While this system seems feasible, there are concerns regarding its performance, in : particular the amount of bending in the po...

  1. Power Management of MEMS-Based Storage Devices for Mobile Systems

    NARCIS (Netherlands)

    Khatib, M.G.; Hartel, Pieter H.

    2008-01-01

    Because of its small form factor, high capacity, and expected low cost, MEMS-based storage is a suitable storage technology for mobile systems. MEMS-based storage devices should also be energy efficient for deployment in mobile systems. The problem is that MEMS-based storage devices are mechanical,

  2. 21 CFR 821.25 - Device tracking system and content requirements: manufacturer requirements.

    Science.gov (United States)

    2010-04-01

    ... HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES MEDICAL DEVICE TRACKING REQUIREMENTS Tracking... procedure for the collection, maintenance, and auditing of the data specified in paragraphs (a) and (b) of... recording system, and the file maintenance procedures system; and (3) A quality assurance program that...

  3. Small animal imaging using a flat panel detector-based cone beam computed tomography (FPD-CBCT) imaging system

    Science.gov (United States)

    Conover, David L.; Ning, Ruola; Yu, Yong; Lu, Xianghua; Wood, Ronald W.; Reeder, Jay E.; Johnson, Aimee M.

    2005-04-01

    Flat panel detector-based cone beam CT (FPD-CBCT) imaging system prototypes have been constructed based on modified clinical CT scanners (a modified GE 8800 CT system and a modified GE HighSpeed Advantage (HSA) spiral CT system) each with a Varian PaxScan 2520 imager. The functions of the electromechanical and radiographic subsystems of the CT system were controlled through specially made hardware, software and data acquisition modules to perform animal cone beam CT studies. Small animal (mouse) imaging studies were performed to demonstrate the feasibility of an optimized CBCT imaging system to have the capability to perform longitudinal studies to monitor the progression of cancerous tumors or the efficacy of treatments. Radiographic parameters were optimized for fast (~10 second) scans of live mice to produce good reconstructed image quality with dose levels low enough to avoid any detectable radiation treatment to the animals. Specifically, organs in the pelvic region were clearly imaged and contrast studies showed the feasibility to visualize small vasculature and space-filling bladder tumors. In addition, prostate and mammary tumors were monitored in volume growth studies.

  4. Reconfiguration of photovoltaic panels for reducing the hydrogen consumption in fuel cells of hybrid systems

    Directory of Open Access Journals (Sweden)

    Daniel González-Montoya

    2017-05-01

    Full Text Available Hybrid generation combines advantages from fuel cell systems with non-predictable generation approaches, such as photovoltaic and wind generators. In such hybrid systems, it is desirable to minimize as much as possible the fuel consumption, for the sake of reducing costs and increasing the system autonomy. This paper proposes an optimization algorithm, referred to as population-based incremental learning, in order to maximize the produced power of a photovoltaic generator. This maximization reduces the fuel consumption in the hybrid aggregation. Moreover, the algorithm's speed enables the real-time computation of the best configuration for the photovoltaic system, which also optimizes the fuel consumption in the complementary fuel cell system. Finally, a system experimental validation is presented considering 6 photovoltaic modules and a NEXA 1.2KW fuel cell. Such a validation demonstrates the effectiveness of the proposed algorithm to reduce the hydrogen consumption in these hybrid systems.

  5. Semimanufacture intended to be mounted on a vibrating wall or a vibrating panel for actively damping vibrations of the wall, wall or panel provided with such semimanufacture, system provided with a semimanufacture and a control unit, wall or panel provided with a control unit and method for damping audible vibrations of a wall or panel

    NARCIS (Netherlands)

    de Goeje, Marius; van Overbeek, Michiel Wilbert R.M.; van der Waal, Adri; Berkhoff, Arthur P.; Nederveen, Peter J.

    2005-01-01

    A semimanufacture intended to be mounted on a vibrating wall or a vibrating panel for actively damping the vibrations in the wall or the panel with frequencies which are at least partly audible, wherein the semimanufacture is provided with a plate wherein the plate is integrated with: at least one

  6. A new design and implementation of an infrared device driver in embedded Linux systems

    Science.gov (United States)

    Jia, Li-li; Cui, Hua; Wang, Ru-li

    2009-07-01

    Wireless infrared communication systems are widely-used for the remote controls in portable terminals, particularly for systems requiring low cost, light weight, moderate data rates. They have already proven their electiveness for short-range temporary communications and in high data rate longer range point-to-point systems. This paper proposes the issue of design and implementation of an infrared device driver in a personal portable intelligent digital infrared communications system. After analyzing the various constraints, we use the embedded system based on Samsung S3C2440A 32-bit processor and Linux operating system to design the driver program. The program abandons its traditional Serial interface control mode, uses the generic GPIO to achieve infrared receiver device driver, and intends a user-defined communication protocol which is much more simple and convenient instead of traditional infrared communication protocol to design the character device drivers for the infrared receiver. The communication protocol uses interrupt counter to determine to receive the value and the first code.In this paper, the interrupt handling and an I/O package to reuse Linux device drivers in embedded system is introduced. Via this package, the whole Linux device driver source tree can be reused without any modifications. The driver program can set up and initialize the infrared device, transfer data between the device and the software, configure the device, monitor and trace the status of the device, reset the device, and shut down the device as requested. At last infrared test procedure was prepared and some testing and evaluations were made in a mobile infrared intelligent cicerone system, and the test result shows that the design is simple, practical, with advantages such as easy transplantation, strong reliability and convenience.

  7. Integrated microwave resonant device for dielectric analysis of microfluidic systems

    Energy Technology Data Exchange (ETDEWEB)

    Rowe, D J; Porch, A; Barrow, D A [School of Engineering, Cardiff University, Cardiff CF24 3AA (United Kingdom); Allender, C J, E-mail: rowedj@cf.ac.uk [Welsh School of Pharmacy, Cardiff University, Cardiff CF24 3NB (United Kingdom)

    2011-08-12

    Herein we present a device for performing non-contact dielectric spectroscopy upon liquids in a microfluidic environment. The device is comprised of a compression-sealed polytetrafluoroethylene (PTFE) chip with an embedded coaxial resonator, which is overmoded for dielectric measurements at six discrete frequencies between 1 and 8 GHz. A novel capacitive coupling structure allows transmission measurements to be taken from one end of the resonator, and an optimised microchannel design maximises sensitivity and repeatability. The use of a PTFE substrate and a non-contact measurement gives excellent chemical and biological compatibility. A simple 'fingerprint' method for identifying solvents is demonstrated, whereby a sample is characterised by air-referenced changes in complex frequency. Complex permittivity values are also obtained via a perturbation theory-based inversion. A combination of experimental and simulated results is used to characterise the device behaviour, limits of operation and measurement uncertainty. The high stability of temporal measurements, coupled with the robustness of the design, make this device ideal for analytical chemistry and industrial process control.

  8. Plant phenometrics systems and methods and devices related thereto

    Energy Technology Data Exchange (ETDEWEB)

    Kramer, David; Cruz, Jeffrey; Hall, Christopher; Kovac, William Kent; Zegarac, Robert

    2016-08-30

    Chlorophyll fluorescence may be studied in response to a variety of environmental cues or conditions by growing phototrophic organisms under actinic illumination. Such illumination may be punctuated or disrupted to gain information about the photosynthetic properties or performance of the phototrophic organism. Instruments or devices for carrying out the method are also described.

  9. Pressurized waterproof case electronic device

    KAUST Repository

    Berumen, Michael L.

    2013-01-31

    A pressurized waterproof case for an electronic device is particularly adapted for fluid-tight containment and operation of a touch-screen electronic device or the like therein at some appreciable water depth. In one example, the case may be formed as an enclosure having an open top panel or face covered by a flexible, transparent membrane or the like for the operation of the touchscreen device within the case. A pressurizing system is provided for the case to pressurize the case and the electronic device therein to slightly greater than ambient in order to prevent the external water pressure from bearing against the transparent membrane and pressing it against the touch screen, thereby precluding operation of the touch screen device within the case. The pressurizing system may include a small gas cartridge or may be provided from an external source.

  10. Application of Devices and Systems Designed for Power Quality Monitoring and Assessment

    Directory of Open Access Journals (Sweden)

    Wiesław Gil

    2014-03-01

    Full Text Available The paper presents the problems associated with increasing demands on the equipment and systems for power quality assessment (PQ, installed at power substations. Difficulties are signaled due to current lack of standards defining the test methodology of measuring devices. The necessary device properties and the structure of a large system operated in real time and designed to assess the PQ are discussed. The usefulness of multi-channel analyzers featuring the identification and registration of transients is pointed out. The desirability of synchrophasor assessment implementation and device integration by standard PN-EN 61850 with other SAS devices is also justified.

  11. Data-acquisition system of the reversed field pinch device REPUTE-1

    International Nuclear Information System (INIS)

    Tsuzuki, N.; Aoki, H.; Shinohara, H.; Toyama, H.; Morikawa, J.

    1988-01-01

    The new, compact data-acquisition system of the reversed field pinch device, REPUTE-1, is reported. Its distinctive feature is high flexibility and easy handling. The interface between the computer and measurement devices is CAMAC. The computer and the CAMAC devices are connected to a CAMAC byte serial highway that transmits setup parameters and acquisition data. The computer carries out setup of CAMAC devices and data acquisition automatically by use of CAMAC parameters and the acquisition data base. The maintenance tools for the data base are also provided. The computer system, which consists of a ''TOSBAC DS-600,'' has been in operation for REPUTE-1 since 1985

  12. LASA (Lidar Atmospheric Sounder and Altimeter) Earth Observing System. Volume 2D: Instrument Panel Report

    Science.gov (United States)

    1987-01-01

    The Earth Observing System (Eos) will provide an ideal forum in which the stronly synergistic characteristics of the lidar systems can be used in concert with the characteristics of a number of other sensors to better understand the Earth as a system. Progress in the development of more efficient and long-lasting laser systems will insure their availability in the Eos time frame. The necessary remote-sensing techniques are being developed to convert the Lidar Atmospheric Sounder and Altimeter (LASA) observations into the proper scientific parameters. Each of these activities reinforces the promise that LASA and GLRS will be a reality in the Eos era.

  13. Concepts and Models Regarding the Behavior of Antiseismic Devices for the Base Isolation System

    Directory of Open Access Journals (Sweden)

    Polidor BRATU

    2013-07-01

    Full Text Available The paper presents the main antiseismic devices, as component elements of the base isolation systems, in such a manner that the functional and constructive parameters are correlated with the inertial and stiffness characteristics of the dynamic isolated building. Also, each device will be characterized through a rheological model, which conditions the eigenvalues and eigenvectors spectrum, as well as the dynamic response to an exterior excitation of a seismic nature. In this context, antiseismic devices defined and characterized by the European Standard EN 15129 will be presented. Based on the requirements formulated in the norm, the devices can be identified and their laws of evolution established and checked as follows: antiseismic devices with permanent rigid connection; antiseismic devices with rigid connections with respect to the instantaneous displacement and antiseismic devices dependent on the velocity and on the velocity variation in time.

  14. NMOS-Based Integrated Modular Bypass for Use in Solar Systems (NIMBUS: Intelligent Bypass for Reducing Partial Shading Power Loss in Solar Panel Applications

    Directory of Open Access Journals (Sweden)

    Pieter Bauwens

    2016-06-01

    Full Text Available NMOS-based Integrated Modular Bypass for Use in Solar systems (NIMBUS is designed as a replacement for the traditional bypass diode, used in common solar panels. Because of the series connection between the individual solar cells, the power output of a photovoltaic (PV panel will drop disproportionally under partial shading. Currently, this is solved by dividing the PV panel into substrings, each with a diode bypass placed in parallel. This allows an alternative current path. However, the diodes still have a significant voltage drop (about 350 mV, and due to the fairly large currents in a panel, the diodes are dissipating power that we would rather see at the output of the panel. The NIMBUS chip, being a low-voltage-drop switch, aims to replace these diodes and, thus, reduce that power loss. NIMBUS is a smart bypass: a completely stand-alone system that detects the failing of one or more cells and activates when necessary. It is designed for a 100-mV voltage drop under a 5-A load current. When two or more NIMBUS chips are placed in parallel, an internal synchronization circuit ensures proper operation to provide for larger load currents. This paper will elaborate on the operation, design and implementation of the NIMBUS chip, as well as on the first measurements.

  15. Development and Implementation of Team-Based Panel Management Tools: Filling the Gap between Patient and Population Information Systems.

    Science.gov (United States)

    Watts, Brook; Lawrence, Renée H; Drawz, Paul; Carter, Cameron; Shumaker, Amy Hirsch; Kern, Elizabeth F

    2016-08-01

    Effective team-based models of care, such as the Patient-Centered Medical Home, require electronic tools to support proactive population management strategies that emphasize care coordination and quality improvement. Despite the spread of electronic health records (EHRs) and vendors marketing population health tools, clinical practices still may lack the ability to have: (1) local control over types of data collected/reports generated, (2) timely data (eg, up-to-date data, not several months old), and accordingly (3) the ability to efficiently monitor and improve patient outcomes. This article describes a quality improvement project at the hospital system level to develop and implement a flexible panel management (PM) tool to improve care of subpopulations of patients (eg, panels of patients with diabetes) by clinical teams. An in-depth case analysis approach is used to explore barriers and facilitators in building a PM registry tool for team-based management needs using standard data elements (eg, laboratory values, pharmacy records) found in EHRs. Also described are factors that may contribute to sustainability; to date the tool has been adapted to 6 disease-focused subpopulations encompassing more than 200,000 patients. Two key lessons emerged from this initiative: (1) though challenging, team-based clinical end users and information technology needed to work together consistently to refine the product, and (2) locally developed population management tools can provide efficient data tracking for frontline clinical teams and leadership. The preliminary work identified critical gaps that were successfully addressed by building local PM registry tools from EHR-derived data and offers lessons learned for others engaged in similar work. (Population Health Management 2016;19:232-239).

  16. A Passive Wireless Multi-Sensor SAW Technology Device and System Perspectives

    Directory of Open Access Journals (Sweden)

    Nikolai Kozlovski

    2013-05-01

    Full Text Available This paper will discuss a SAW passive, wireless multi-sensor system under development by our group for the past several years. The device focus is on orthogonal frequency coded (OFC SAW sensors, which use both frequency diversity and pulse position reflectors to encode the device ID and will be briefly contrasted to other embodiments. A synchronous correlator transceiver is used for the hardware and post processing and correlation techniques of the received signal to extract the sensor information will be presented. Critical device and system parameters addressed include encoding, operational range, SAW device parameters, post-processing, and antenna-SAW device integration. A fully developed 915 MHz OFC SAW multi-sensor system is used to show experimental results. The system is based on a software radio approach that provides great flexibility for future enhancements and diverse sensor applications. Several different sensor types using the OFC SAW platform are shown.

  17. EFFICIENCY OPTIMIZATION OF ATTENDANCE SYSTEM WITH GPS AND BIOMETRIC METHOD USING MOBILE DEVICES

    OpenAIRE

    Benfano Soewito; Echo Wahana Marciano Simanjuntak

    2014-01-01

    The existing attendance system still has drawbacks, namely the queue in front of the finger scanner, the attendance data are not integrated with Human Resources Systems, and also the employees who work outside the office cannot get in the attendance system to roll presence. In the other hand, everyone has the mobile devices and all the mobile devices will be embedded a finger scanner in the future. In this paper, it is proposed the absence system using one own device. The finger scanner and c...

  18. Use of the Perclose ProGlide device with the 9 French Merci retrieval system

    Energy Technology Data Exchange (ETDEWEB)

    Layton, Kennith F.; Cloft, Harry J.; Kallmes, David F. [Mayo Clinic, Department of Radiology, Rochester, MN (United States); White, J. Bradley [Mayo Clinic, Department of Neurosurgery, Rochester, MN (United States)

    2006-05-15

    Closure devices are commonly used in neurointerventional procedures to achieve groin hemostasis. These devices are particularly useful in procedures requiring anticoagulation and larger catheters. The suture-mediated Perclose ProGlide device is intended for use with 5F to 8F sheaths. We describe the use of the ProGlide device with 9F sheaths in acute stroke treatment using the Merci retrieval device. The ProGlide device is advanced over a wire until the wire exit port is at the skin surface. The wire is removed and the device is advanced until pulsatile blood flow is encountered. The footplates are opened and the stitch is deployed. The footplates are then closed and the device is removed. After advancing the suture to the vessel, it is locked and trimmed. Firm pressure is necessary during deployment to prevent oozing around the device. If continued bleeding is encountered, direct manual pressure is used to achieve hemostasis. We have successfully used the Perclose ProGlide device in four patients following the Merci retriever without groin or extremity complication. The Perclose ProGlide device can be successfully used after placement of a 9F system in patients who have undergone mechanical thrombectomy. (orig.)

  19. Installation package for concentrating solar collector panels

    Science.gov (United States)

    1978-01-01

    The concentrating solar collector panels comprise a complete package array consisting of collector panels using modified Fresnel prismatic lenses for a 10 to 1 concentrating ratio, supporting framework, fluid manifolding and tracking drive system, and unassembled components for field erection.

  20. Do intrauterine device/intrauterine system users check their threads?

    Science.gov (United States)

    Davies, Amanda; Fleming, Charlotte

    2014-04-01

    Expulsion of an intrauterine device (IUD) occurs in about 1 in 20 women and expulsion may not be noticed by the user. Current guidance recommends that users are instructed to check regularly for their threads. This is the first study to explore the reality of how women feel about checking their threads and the details surrounding how frequently checks are done. One hundred consecutive IUD users were interviewed regarding their type of device, duration of use, frequency of thread checking, prompts for checking and reasons for not checking. Only 23% checked their threads regularly and 51% had never done so. The most common reason for not checking was forgetting about it. Despite being advised to do so, the majority of users do not check their threads at all and fewer than one-quarter of them check regularly. We propose that advice offered about thread checking should be given less emphasis and suggested more for user reassurance.

  1. Evaluation of Galvanized and Galvalume/Paint Duplex Coating Systems for Steel Building Panels

    National Research Council Canada - National Science Library

    Race, Timothy

    2002-01-01

    ...) or silicone modified polyester (SMP). Specimens having these coating systems were subjected to ASTM B 117, conventional salt spray exposure testing and ASTM D 5894 Testing in the laboratory, which combines the environmental effects...

  2. Simulation of Photovoltaic Panel Production as Complement to Ground Source Heat Pump System

    OpenAIRE

    Badri, Seyed Ali Mohammad

    2013-01-01

    This master thesis presents a new technological combination of two environmentally friendly sources of energy in order to provide DHW, and space heating. Solar energy is used for space heating, and DHW production using PV modules which supply direct current directly to electrical heating elements inside a water storage tank. On the other hand a GSHP system as another source of renewable energy provides heat in the water storage tank of the system in order to provide DHW and space heating. The...

  3. Temperature Dependences on Various Types of Photovoltaic (PV) Panel

    International Nuclear Information System (INIS)

    Audwinto, I A; Leong, C S; Sopian, K; Zaidi, S H

    2015-01-01

    Temperature is one of the key roles in PV technology performance, since with the increases of temperature the open-circuit voltage will drop accordingly so do the electrical efficiency and power output generation. Different types of Photovoltaic (PV) panels- silicon solar panels and thin film solar panels; mono-crystalline, poly-crystalline, CIS, CIGS, CdTe, back-contact, and bi-facial solar panel under 40°C to 70°C approximately with 5°C interval have been comparatively analyzed their actual performances with uniformly distribution of light illumination from tungsten halogen light source, ±500W/m 2 . DC-Electronic Load and Data Logger devices with “Lab View” data program interface were used to collect all the necessary parameters in this study. Time needed to achieve a certain degree of temperature was recorded. Generally, each of the panels needed 15 minutes to 20 minutes to reach 70°C. Halogen based light source is not compatible in short wave-length in response to thin-film solar cell. Within this period of times, all the panels are facing a performance loss up to 15%. Other parameters; P max , V max , I max , V oc , I sc , R serries , R shunt , Fillfactor were collected as study cases. Our study is important in determining Photovoltaic type selection and system design as for study or industrial needed under different temperature condition. (paper)

  4. Circuits in the Sun: Solar Panel Physics

    Science.gov (United States)

    Gfroerer, Tim

    2013-01-01

    Typical commercial solar panels consist of approximately 60 individual photovoltaic cells connected in series. Since the usual Kirchhoff rules apply, the current is uniform throughout the circuit, while the electric potential of the individual devices is cumulative. Hence, a solar panel is a good analog of a simple resistive series circuit, except…

  5. Effects and Satisfaction of Medical Device Safety Information Reporting System Using Electronic Medical Record.

    Science.gov (United States)

    Jang, Hye Jung; Choi, Young Deuk; Kim, Nam Hyun

    2017-04-01

    This paper describes an evaluation study on the effectiveness of developing an in-hospital medical device safety information reporting system for managing safety information, including adverse incident data related to medical devices, following the enactment of the Medical Device Act in Korea. Medical device safety information reports were analyzed for 190 cases that took place prior to the application of a medical device safety information reporting system and during a period when the reporting system was used. Also, questionnaires were used to measure the effectiveness of the medical device safety information reporting system. The analysis was based on the questionnaire responses of 15 reporters who submitted reports in both the pre- and post-reporting system periods. Sixty-two reports were submitted in paper form, but after the system was set up, this number more than doubled to 128 reports in electronic form. In terms of itemized reporting, a total of 45 items were reported. Before the system was used, 23 items had been reported, but this increased to 32 items after the system was put to use. All survey variables of satisfaction received a mean of over 3 points, while positive attitude , potential benefits , and positive benefits all exceeded 4 points, each receiving 4.20, 4.20, and 4.13, respectively. Among the variables, time-consuming and decision-making had the lowest mean values, each receiving 3.53. Satisfaction was found to be high for system quality and user satisfaction , but relatively low for time-consuming and decision-making . We were able to verify that effective reporting and monitoring of adverse incidents and the safety of medical devices can be implemented through the establishment of an in-hospital medical device safety information reporting system that can enhance patient safety and medical device risk management.

  6. Solar Panel System for Street Light Using Maximum Power Point Tracking (MPPT Technique

    Directory of Open Access Journals (Sweden)

    Wiedjaja A.

    2014-03-01

    Full Text Available Solar energy is one form of the renewable energy which is very abundant in regions close to the equator. One application of solar energy is for street light. This research focuses on using the maximum power point tracking technique (MPPT, particularly the perturb and observe (P&O algorithm, to charge battery for street light system. The proposed charger circuit can achieve 20.73% higher power efficiency compared to that of non-MPPT charger. We also develop the LED driver circuit for the system which can achieve power efficiency up to 91.9% at a current of 1.06 A. The proposed street lightning system can be implemented with a relatively low cost for public areas.

  7. Grounds of two positions photovoltaic panels

    OpenAIRE

    Castán Fortuño, Fernando

    2008-01-01

    The objective of this Master Thesis is to find the optimum positioning for a two positions photovoltaic panel. Hence, it will be implemented a model in order to optimize the energy of the sun that the photovoltaic panel is receiving by its positioning. Likewise this project will include the comparison with other photovoltaic panel systems as the single position photovoltaics panels. Ultimately, it is also going to be designed a system array for the optimized model of two positions photovoltai...

  8. The Best Efficiency Point of the Performance of Solar Cell Panel System for Pumping Water at Various Lifting Heads Using 100 W Motor Pump Unit

    OpenAIRE

    Himran, Sukri

    2013-01-01

    This study was carried out experimentally and analytically about the performance of solar cell panel system for operating the pump coupled by dc motor. The solar cell panel with total area 1.9848 m2 consists of three modules of 80 Wp each. The small centrifugal pump powered by dc motor is operated to lift water from 1m to 7m heads in sequence and gives the amount of water pumped over the whole day from 08.00 to 16.00 h are 11988, 10851, 8874, 7695, 5760, 3600...

  9. The Best Efficiency Point of the Performance of Solar Cell Panel System for Pumping Water at Various Lifting Heads Using 100 W Motor- Pump Unit

    OpenAIRE

    S. Himran; B. Mire; N. Salam; L. Sule

    2013-01-01

    This study was carried out experimentally and analytically about the performance of solar cell panel system for operating the pump coupled by dc-motor. The solar cell panel with total area 1.9848 m2 consists of three modules of 80 Wp each. The small centrifugal pump powered by dc-motor is operated to lift water from 1m to 7m heads in sequence and gives the amount of water pumped over the whole day from 08.00 to 16.00 h are 11988, 10851, 8874, 7695, 5760, 3600, 2340 L/d respectively. The hourl...

  10. A biomarker panel to discriminate between systemic inflammatory response syndrome SIRS and sepsis and sepsis severity

    NARCIS (Netherlands)

    Punyadeera, C.; Schneider, E. M.; Schaffer, D.; Hsu, H-Y.; Joos, T.O.; Kriebel, F; Weiss, M.; Verhaegh, W.F.J.

    2009-01-01

    In this study we report on initial efforts to discover putative biomarkers for differential diagnosis of a systemic inflammatory response syndrome (SIRS) vs. sepsis; and different stages of sepsis. In addition, we also investigated whether there are proteins that can discriminate between patients

  11. Advanced solar panel designs

    Science.gov (United States)

    Ralph, E. L.; Linder, E.

    1995-01-01

    This paper describes solar cell panel designs that utilize new hgih efficiency solar cells along with lightweight rigid panel technology. The resulting designs push the W/kg and W/sq m parameters to new high levels. These new designs are well suited to meet the demand for higher performance small satellites. This paper reports on progress made on two SBIR Phase 1 contracts. One panel design involved the use of large area (5.5 cm x 6.5 cm) GaAs/Ge solar cells of 19% efficiency combined with a lightweight rigid graphite fiber epoxy isogrid substrate configuration. A coupon (38 cm x 38 cm) was fabricated and tested which demonstrated an array specific power level of 60 W/kg with a potential of reaching 80 W/kg. The second panel design involved the use of newly developed high efficiency (22%) dual junction GaInP2/GaAs/Ge solar cells combined with an advanced lightweight rigid substrate using aluminum honeycomb core with high strength graphite fiber mesh facesheets. A coupon (38 cm x 38 cm) was fabricated and tested which demonstrated an array specific power of 105 W/kg and 230 W/sq m. This paper will address the construction details of the panels and an a analysis of the component weights. A strawman array design suitable for a typical small-sat mission is described for each of the two panel design technologies being studied. Benefits in respect to weight reduction, area reduction, and system cost reduction are analyzed and compared to conventional arrays.

  12. The spatial and logical organization of devices in an advanced industrial robot system

    Science.gov (United States)

    Ruoff, C. F.

    1980-01-01

    This paper describes the geometrical and device organization of a robot system which is based in part upon transformations of Cartesian frames and exchangeable device tree structures. It discusses coordinate frame transformations, geometrical device representation and solution degeneracy along with the data structures which support the exchangeable logical-physical device assignments. The system, which has been implemented in a minicomputer, supports vision, force, and other sensors. It allows tasks to be instantiated with logically equivalent devices and it allows tasks to be defined relative to appropriate frames. Since these frames are, in turn, defined relative other frames this organization provides a significant simplification in task specification and a high degree of system modularity.

  13. Performance Modeling of Network-Attached Storage Device Based Hierarchical Mass Storage Systems

    Science.gov (United States)

    Menasce, Daniel A.; Pentakalos, Odysseas I.

    1995-01-01

    Network attached storage devices improve I/O performance by separating control and data paths and eliminating host intervention during the data transfer phase. Devices are attached to both a high speed network for data transfer and to a slower network for control messages. Hierarchical mass storage systems use disks to cache the most recently used files and a combination of robotic and manually mounted tapes to store the bulk of the files in the file system. This paper shows how queuing network models can be used to assess the performance of hierarchical mass storage systems that use network attached storage devices as opposed to host attached storage devices. Simulation was used to validate the model. The analytic model presented here can be used, among other things, to evaluate the protocols involved in 1/0 over network attached devices.

  14. Application of complex programmable logic devices in memory radiation effects test system

    International Nuclear Information System (INIS)

    Li Yonghong; He Chaohui; Yang Hailiang; He Baoping

    2005-01-01

    The application of the complex programmable logic device (CPLD) in electronics is emphatically discussed. The method of using software MAX + plus II and CPLD are introduced. A new test system for memory radiation effects is established by using CPLD devices-EPM7128C84-15. The old test system's function are realized and, moreover, a number of small scale integrated circuits are reduced and the test system's reliability is improved. (authors)

  15. Development of device drivers embedded in real time OS for SPring-8 SR control system

    International Nuclear Information System (INIS)

    Masuda, T.; Fujiwara, S.; Nakamura, T.; Takebe, H.; Wada, T.

    1994-01-01

    A distributed computer system has been adopted for the SPring-8 SR control system. For lower level computers, we intend to adopt VMEbus computer systems with the real time OS which are compliant with POSIX. For R and D study, we introduced LynxOS and wrote device drivers for Digital Output(DO), Digital Input(DI) and Analog Input(AI) boards on VMEbus. They were successfully operated with device drivers. (author)

  16. Device for supply and discharge of coupling medium ultrasonic probe system

    International Nuclear Information System (INIS)

    Zuzo, M.

    1989-01-01

    The device allows to bring in the coupling medium through a single integrated distributor. The distribution system rotates together with the lower revolving plate on which is mounted the system of ultrasonic probes. This removes the undesirable force side-effects on the configuration of the probes from the supply hoses. The device may be used for one probe or for a whole system of probes. (J.B.). 1 fig

  17. Development of gas-sampling device for 13N monitoring system

    International Nuclear Information System (INIS)

    Zhao Lihong; Gong Xueyu

    2003-01-01

    The 13 N monitoring system is used in the monitoring of the rate of leakage of the primary coolant circuit in nuclear power stations. The author introduces a gas-sampling device of the 13 Nmonitoring system. It is with a close-loop flow control system with intelligent control of Single Chip Micyoco (SCM), and has the ability to monitor and replace the filter paper automatically, to increase the automation of the device and stable operation in long time

  18. Characteristics and applications of a flat panel computer tomography system; Eigenschaften und Anwendungen der Flaechendetektor-basierten Volumen-Computertomographie

    Energy Technology Data Exchange (ETDEWEB)

    Knollmann, F.; Valencia, R.; Obenauer, S. [Abt. Diagnostische Radiologie, Klinikum der Georg-August-Univ. Goettingen (Germany); Buhk, J.H. [Abt. Neuroradiologie, Univ. Goettingen (Germany)

    2006-09-15

    Purpose: to assess a new flat panel volume computed tomography (FP-VCT) with very high isotropic spatial resolution as well as high Z-axis coverage. Materials and Methods: The prototype of an FP-VCT scanner with a detector cell size of 0.2 mm was used for numerous phantom studies, specimen examinations, and animal research projects. Results: The high spatial resolution of the new system can be used to accurately determine solid tumor volume, thus allowing for earlier assessment of the therapeutic response. In animal experimentation, whole-body perfusion mapping of mice is feasible. The high spatial resolution also improves the classification of coronary artery atherosclerotic plaques in the isolated post mortem human heart. With the depiction of intramyocardial segments of the coronary arteries, investigations of myocardial collateral circulation are feasible. In skeletal applications, an accurate analysis of the smallest bony structures, e.g., petrous bone and dental preparations, can be successfully performed, as well as investigations of repetitive studies of fracture healing and the treatment of osteoporosis. Conclusion: The introduction of FP-VCT opens up new applications for CT, including the field of molecular imaging, which are highly attractive for future clinical applications. Present limitations include limited temporal resolution and necessitate further improvement of the system. (orig.)

  19. Optimizing MEMS-Based Storage Devices for Mobile Battery-Powered Systems

    NARCIS (Netherlands)

    Khatib, M.G.; Hartel, Pieter H.

    An emerging storage technology, called MEMS-based storage, promises nonvolatile storage devices with ultrahigh density, high rigidity, a small form factor, and low cost. For these reasons, MEMS-based storage devices are suitable for battery-powered mobile systems such as PDAs. For deployment in such

  20. A simple optical fibre-linked remote control system for multiple devices

    Indian Academy of Sciences (India)

    MS received 11 June 2003. Abstract. We report on the development of a simple control system which can handle multiple devices through an optical fibre data link. The devices are controlled using a set of DACs through serial data communication via a serial port of a PC. Serial data from the PC get converted to parallel ...

  1. A nanosecond high voltage pulse device for accelerator time analytical system

    International Nuclear Information System (INIS)

    Lou Binqiao; Ding Furong; Xue Zhihua; Wang Xuemei; Shen Dingyu

    2002-01-01

    A nanosecond high voltage pulse device has been designed. The pulse rise time is 10 ns. The pulse voltage reached 16000 V. This device has been used to accelerator time analytical system, its resolution time is less than 0.8%

  2. A simple optical fibre-linked remote control system for multiple devices

    Indian Academy of Sciences (India)

    We report on the development of a simple control system which can handle multiple devices through an optical fibre data link. The devices are controlled using a set of DACs through serial data communication via a serial port of a PC. Serial data from the PC get converted to parallel mode using a homemade “serial in ...

  3. Development of Hand Grip Assistive Device Control System for Old People through Electromyography (EMG Signal Acquisitions

    Directory of Open Access Journals (Sweden)

    Khamis Herman

    2017-01-01

    Full Text Available The hand grip assistive device is a glove to assist old people who suffer from hand weakness in their daily life activities. The device earlier control system only use simple on and off switch. This required old people to use both hand to activate the device. The new control system of the hand grip assistive device was developed to allow single hand operation for old people. New control system take advantages of electromyography (EMG and flex sensor which was implemented to the device. It was programmed into active and semi-active mode operation. EMG sensors were placed on the forearm to capture EMG signal of Flexor Digitorum Profundus muscle to activate the device. Flex sensor was used to indicate the finger position and placed on top of the finger. The signal from both sensors then used to control the device. The new control system allowed single hand operation and designed to prevent user from over depended on the device by activating it through moving their fingers.

  4. Interference of regional support policies on the economic and environmental performance of a hybrid cogeneration-solar panel energy system

    International Nuclear Information System (INIS)

    Maes, Dries; Van Passel, Steven

    2012-01-01

    This paper assesses unintentional interference between different public policies promoting energy efficiency and renewable energy. The paper develops a methodology to study the interference by analysing the economic and technical behaviour of a hybrid energy system. The hybrid energy system in this case consists of an existing cogeneration unit extended with a new installation of thermal solar panels. This puts two complementary heating technologies in juxtaposition. The two technologies are supported with distinct regional support instruments in each region. The design and operation of the energy system is optimised from the point of view of the investor according to the different support instruments. The optimal configuration is analysed as well as its effect on reduced CO 2 -emissions during the lifetime of the project. The methodology is applied to a case-study for two neighbouring regions, the Netherlands and Flanders. The policies in the Netherlands show a beneficial synergy. In Flanders, the hybrid energy system is not interesting, indicating unbalanced high support for cogeneration in this case. From the point of view of the authorities, a more balanced regional policy as in the Netherlands provides a larger CO 2 -emission reduction for a smaller cost. - Highlights: ► Study of interference between various public policies by analysing a hybrid energy system. ► A methodology based on maximum value for the investor based on different public policies. ► Case study in the Netherlands show policies with a beneficial synergy. ► Situation in Flanders indicates unbalanced policies and larger cost for CO 2 -emission reduction.

  5. DeviceGuard: External Device-Assisted System And Data Security

    OpenAIRE

    Deng, Yipan

    2011-01-01

    This thesis addresses the threat that personal computer faced from malware when the personal computer is connected to the Internet. Traditional host-based security approaches, such as anti-virus scanning protect the host from virus, worms, Trojans and other malwares. One of the issues of the host-based security approaches is that when the operating system is compromised by the malware, the antivirus software also becomes vulnerable. In this thesis, we present a novel approach through usin...

  6. Launch Lock Assemblies Including Axial Gap Amplification Devices and Spacecraft Isolation Systems Including the Same

    Science.gov (United States)

    Barber, Tim Daniel (Inventor); Hindle, Timothy (Inventor); Young, Ken (Inventor); Davis, Torey (Inventor)

    2014-01-01

    Embodiments of a launch lock assembly are provided, as are embodiments of a spacecraft isolation system including one or more launch lock assemblies. In one embodiment, the launch lock assembly includes first and second mount pieces, a releasable clamp device, and an axial gap amplification device. The releasable clamp device normally maintains the first and second mount pieces in clamped engagement; and, when actuated, releases the first and second mount pieces from clamped engagement to allow relative axial motion there between. The axial gap amplification device normally residing in a blocking position wherein the gap amplification device obstructs relative axial motion between the first and second mount pieces. The axial gap amplification device moves into a non-blocking position when the first and second mount pieces are released from clamped engagement to increase the range of axial motion between the first and second mount pieces.

  7. Evaluation of a CLEIA automated assay system for the detection of a panel of tumor markers.

    Science.gov (United States)

    Falzarano, Renato; Viggiani, Valentina; Michienzi, Simona; Longo, Flavia; Tudini, Silvestra; Frati, Luigi; Anastasi, Emanuela

    2013-10-01

    Tumor markers are commonly used to detect a relapse of disease in oncologic patients during follow-up. It is important to evaluate new assay systems for a better and more precise assessment, as a standardized method is currently lacking. The aim of this study was to assess the concordance between an automated chemiluminescent enzyme immunoassay system (LUMIPULSE® G1200) and our reference methods using seven tumor markers. Serum samples from 787 subjects representing a variety of diagnoses, including oncologic, were analyzed using LUMIPULSE® G1200 and our reference methods. Serum values were measured for the following analytes: prostate-specific antigen (PSA), alpha-fetoprotein (AFP), carcinoembryonic antigen (CEA), cancer antigen 125 (CA125), carbohydrate antigen 15-3 (CA15-3), carbohydrate antigen 19-9 (CA19-9), and cytokeratin 19 fragment (CYFRA 21-1). For the determination of CEA, AFP, and PSA, an automatic analyzer based on chemiluminescence was applied as reference method. To assess CYFRA 21-1, CA125, CA19-9, and CA15-3, an immunoradiometric manual system was employed. Method comparison by Passing-Bablok analysis resulted in slopes ranging from 0.9728 to 1.9089 and correlation coefficients from 0.9977 to 0.9335. The precision of each assay was assessed by testing six serum samples. Each sample was analyzed for all tumor biomarkers in duplicate and in three different runs. The coefficients of variation were less than 6.3 and 6.2 % for within-run and between-run variation, respectively. Our data suggest an overall good interassay agreement for all markers. The comparison with our reference methods showed good precision and reliability, highlighting its usefulness in clinical laboratory's routine.

  8. Memorandum for public panel discussants and others interested in the proposed financial reporting system (FRS)

    Energy Technology Data Exchange (ETDEWEB)

    Rodgers, G.M.

    1977-07-11

    This is the information package for the FEA Petroleum Company Financial Reporting System (FRS). The following are included: set of FRS forms and instructions, a schedule requiring a 10 year history of exploration and development expenditures and reserve additions, a schedule which separates the refining and marketing functions, a copy of the Federal Register notice, and a set of FRS data displays which show how financial operating and net asset data reported on the FRS form might be arranged to prepare an information report. (DLC)

  9. Panel C report: Standards needed for the use of ISO Open Systems Interconnection - basic reference model

    Science.gov (United States)

    1981-01-01

    The use of an International Standards Organization (ISO) Open Systems Interconnection (OSI) Reference Model and its relevance to interconnecting an Applications Data Service (ADS) pilot program for data sharing is discussed. A top level mapping between the conjectured ADS requirements and identified layers within the OSI Reference Model was performed. It was concluded that the OSI model represents an orderly architecture for the ADS networking planning and that the protocols being developed by the National Bureau of Standards offer the best available implementation approach.

  10. System constitution of plasma high frequency heating device and element equipment

    International Nuclear Information System (INIS)

    Nagashima, Takashi

    1988-01-01

    On the high frequency heating device used for nuclear fusion experiment, the system constitution and the main items of development for the element equipment are described. As for the high frequency heating device, large technical progress was observed in the past 10 years as the second stage heating for tokamaks and one of the main means of current drive. At present, three frequency zones are regarded as promising for plasma high frequency heating in large nuclear fusion devices, and the experiment of 10 MW class is in progress at JT-60, JET and so on. There are electron cyclotron heating, lower hybrid resonance frequency heating and ion cyclotron range of frquency heating. The basic constitution of these heating devices includes a high frequency source, a transmission system, a connection system, and a common system for control, cooling, record and others. The ECH device using gyrotrons of several tens GHz, the LHRF heating device using large power klystrons up to several GHz and the ICRF heating device up to 200 MHz are briefly explained. The main element equipments composing the high frequency heating systems of several tens MW are discussed. (Kako, I.)

  11. A computational system for analyze nuclear power plants structures, made by panels, using superelements

    International Nuclear Information System (INIS)

    Jesus Miranda, C.A. de.

    1981-03-01

    The analysis of linear static behavior of folded-plate structures like the turbine building of a nuclear power plant by the Finite Element Method. Folded-plate isoparametric plane elements with 48 degrees of freedom each, 8 nodal points, in which shear deformations are considered, and super-elements, whose internal degrees of freedom are condensated, are used. Arbitrary shells can be analized too. A brief exposition of the method is present and the developing of the foregoing element and super-element is also shown. A computer program was developed for the CDC-CYBER 175 computer machine and the FORTRAN IV language was used. The coeficients of the equations system are stored by the technique of block partitioning with a compacted column storage scheme and special attention was dedicated to the preparation of the problem's data and some options were developed for this purpose. (Author) [pt

  12. A City Parking Integration System Combined with Cloud Computing Technologies and Smart Mobile Devices

    Science.gov (United States)

    Yeh, Her-Tyan; Chen, Bing-Chang; Wang, Bo-Xun

    2016-01-01

    The current study applied cloud computing technology and smart mobile devices combined with a streaming server for parking lots to plan a city parking integration system. It is also equipped with a parking search system, parking navigation system, parking reservation service, and car retrieval service. With this system, users can quickly find…

  13. Analysis of operations and cyber security policies for a system of cooperating Flexible Alternating Current Transmission System (FACTS) devices.

    Energy Technology Data Exchange (ETDEWEB)

    Phillips, Laurence R.; Tejani, Bankim; Margulies, Jonathan; Hills, Jason L.; Richardson, Bryan T.; Baca, Micheal J.; Weiland, Laura

    2005-12-01

    Flexible Alternating Current Transmission Systems (FACTS) devices are installed on electric power transmission lines to stabilize and regulate power flow. Power lines protected by FACTS devices can increase power flow and better respond to contingencies. The University of Missouri Rolla (UMR) is currently working on a multi-year project to examine the potential use of multiple FACTS devices distributed over a large power system region in a cooperative arrangement in which the FACTS devices work together to optimize and stabilize the regional power system. The report describes operational and security challenges that need to be addressed to employ FACTS devices in this way and recommends references, processes, technologies, and policies to address these challenges.

  14. Ultrasonic scanner for radial and flat panels

    Science.gov (United States)

    Spencer, R. L.; Hill, E. K. (Inventor)

    1973-01-01

    An ultrasonic scanning mechanism is described that scans panels of honeycomb construction or with welded seams. It incorporates a device which by simple adjustment is adapted to scan either a flat panel or a radial panel. The supporting structure takes the form of a pair of spaced rails. An immersion tank is positioned between the rails and below their level. A work holder is mounted in the tank and is adapted to hold the flat or radial panel. A traveling bridge is movable along the rails and a carriage is mounted on the bridge.

  15. [Life expectancy, strenuous work and pension system's fairness. First evidence from the Work Histories Italian Panel].

    Science.gov (United States)

    Leombruni, Roberto; Richiardi, Matteo; Demaria, Moreno; Costa, Giuseppe

    2010-01-01

    the study aims to estimate the differentials in life expectancy by income and work history in Italy during the 2000's, in order to evaluate the level of actuarial equity of the recent Italian retirement reform in computing benefits proportional to the contributions paid. retrospective cohort study. mortality follow up of a 1% sample of the Italian workforce employed or self employed in the private sector, retired between 1985 and 2003 (about 63,000 people), whose work history and income since 1985 is registered in the National Institute for Social Insurance (INPS) data base. mortality differentials computed through Cox model. social inequalities in survival in favour of the more advantaged categories of income and occupational classes are observed. the principle of actuarial equity assumes that life expectancy varies only according to age and birth cohort; nevertheless inequalities in life expectancy exist also along other dimensions, like income and occupational class: this means that the system is producing an opposite redistribution, from the careers more socially disadvantaged to the less disadvantaged ones.

  16. Solar Trigeneration: a Transitory Simulation of HVAC Systems Using Different Typologies of Hybrid Panels

    Directory of Open Access Journals (Sweden)

    Alejandro del Amo Sancho

    2014-03-01

    Full Text Available The high energy demand on buildings requires efficient installations and the integration of renewable energy to achieve the goal of reducing energy consumption using traditional energy sources. Usually, solar energy generation and heating loads have different profiles along a day and their maximums take place at different moments. In addition, in months in which solar production is higher, the heating demands are the minimum (hot water is consumed only domestically in summer. Cooling machines (absorption and adsorption allow using thermal energy to chill a fluid. This heat flow rate could be recovered from solar collectors or any other heat source. The aim of this study is to integrate different typologies of solar hybrid (photovoltaic and thermal collectors with cooling machines getting solar trigeneration and concluding the optimal combination for building applications. The heat recovered from the photovoltaic module is used to provide energy to these cooling machines getting a double effect: to get a better efficiency on PV modules and to cool the building. In this document the authors analyse these installations, their operating conditions, dimensions and parameters, in order to get the optimal installation in three different European cities. This work suggests that in a family house in Madrid, the optimal combination is to use CPVT with azimuthally tracking and absorption machine. In this case, the solar trigeneration system using 55 m2 of collector area saves the cooling loads and 79% of the heating load in the house round the year.

  17. Automatic cross-sectioning and monitoring system locates defects in electronic devices

    Science.gov (United States)

    Jacobs, G.; Slaughter, B.

    1971-01-01

    System consists of motorized grinding and lapping apparatus, sample holder, and electronic control circuit. Low power microscope examines device to pinpoint location of circuit defect, and monitor displays output signal when defect is located exactly.

  18. Statistical analysis and optimization in the process/device/circuit/system microelectronics design

    OpenAIRE

    Kuleshov, A.; Nelayev, V.; Stempitsky, V.

    2010-01-01

    Methodology and results of statistical analysis and optimization in the joined process/device/circuit/system microelectronics design are presented. A simple example of the cell inverter design illustrates the e±ciency of the methodology.

  19. 76 FR 22726 - Certain Multimedia Display and Navigation Devices and Systems, Components Thereof, and Products...

    Science.gov (United States)

    2011-04-22

    ... INTERNATIONAL TRADE COMMISSION [Investigation No. 337-TA-694] Certain Multimedia Display and Navigation Devices and Systems, Components Thereof, and Products Containing Same; Notice of Commission... importation, and the sale within the United States after importation of certain multimedia display and...

  20. Demonstration of Silicon Carbide Power Devices in Practical Power Conversion Systems

    National Research Council Canada - National Science Library

    Cooper, James A., Jr; Sudhoff, Scott D; Kwon, C; Glover, S. F

    2005-01-01

    ...) with blocking voltages above 1,000 V and on-state currents above 25 A; (2) to fabricate and package sufficient quantities of these devices to implement a demonstration motor control system; (3...

  1. Combined Resource Allocation System for Device-to-Device Communication towards LTE Networks

    Directory of Open Access Journals (Sweden)

    Abbas Fakhar

    2016-01-01

    Full Text Available The LTE networks are being developed to grant mobile broadband services in the fourth generation (4G systems and allow operators to use spectrum more efficiently.D2D communication is a promising technique to provide wireless services and enhance spectrum exploitation in the LTE Heterogeneous Networks (HetNets.D2D communication in HetNets allows users to communicate with each other directly by reusing the resources when communicating via the base stations. But during the downlink period, both the D2D receiver and the Heterogeneous Users equipment’s (HUE experience interference caused by resource allocation. In this article, we identify and analyze the interference problem of HetNets caused by D2D transmitter during download. We propose a combined resource allocation and resource reuse method for LTE HetNets, where resource allocation to HUEs is employed on the basis of comparative fair algorithm and resource reuse to D2D users is employed on acquisitive empirical algorithm. This approach evaluates whether D2D mode is suitable or not by path loss evaluation, after that decreases the interference to HUE by selection of the minimum channel gain between HUE and D2D transmitter each time to mitigate interference. Our simulation results show that the efficiency and throughput of HetNets is improved by using the proposed method.

  2. Systems genetics of intravenous cocaine self-administration in the BXD recombinant inbred mouse panel.

    Science.gov (United States)

    Dickson, Price E; Miller, Mellessa M; Calton, Michele A; Bubier, Jason A; Cook, Melloni N; Goldowitz, Daniel; Chesler, Elissa J; Mittleman, Guy

    2016-02-01

    Cocaine addiction is a major public health problem with a substantial genetic basis for which the biological mechanisms remain largely unknown. Systems genetics is a powerful method for discovering novel mechanisms underlying complex traits, and intravenous drug self-administration (IVSA) is the gold standard for assessing volitional drug use in preclinical studies. We have integrated these approaches to identify novel genes and networks underlying cocaine use in mice. Mice from 39 BXD strains acquired cocaine IVSA (0.56 mg/kg/infusion). Mice from 29 BXD strains completed a full dose-response curve (0.032-1.8 mg/kg/infusion). We identified independent genetic correlations between cocaine IVSA and measures of environmental exploration and cocaine sensitization. We identified genome-wide significant quantitative trait loci (QTL) on chromosomes 7 and 11 associated with shifts in the dose-response curve and on chromosome 16 associated with sessions to acquire cocaine IVSA. Using publicly available gene expression data from the nucleus accumbens, midbrain, and prefrontal cortex of drug-naïve mice, we identified Aplp1 and Cyfip2 as positional candidates underlying the behavioral QTL on chromosomes 7 and 11, respectively. A genome-wide significant trans-eQTL linking Fam53b (a GWAS candidate for human cocaine dependence) on chromosome 7 to the cocaine IVSA behavioral QTL on chromosome 11 was identified in the midbrain; Fam53b and Cyfip2 were co-expressed genome-wide significantly in the midbrain. This finding indicates that cocaine IVSA studies using mice can identify genes involved in human cocaine use. These data provide novel candidate genes underlying cocaine IVSA in mice and suggest mechanisms driving human cocaine use.

  3. Control panel for CMC 8080 crate controller

    International Nuclear Information System (INIS)

    Masayuki Inokuchi

    1978-01-01

    The main features of Control Panel for CAMAC Crate Controller CMC 8080 are described. The control panel can be directly connected with CRATE CONTROLLER's front panel connector with a 50 lines cable without any changes in CMC 8080 system circuits. (author)

  4. The upgraded control and instrumentation system of C5 irradiation device

    International Nuclear Information System (INIS)

    Iordache, A.; Ancuta, M.; Gruia, L.; Pulpa, A.; Salistean, E.; Gusescu, G.

    2013-01-01

    C5 capsule is an irradiation device of TRIGA SSR, which is designed for irradiation of structural materials in an inert environment for mechanical behavior characterization and the material microstructure evolution during irradiation. The paper presents the upgraded control and instrumentation system of the C5 irradiation device which was designed and manufactured to enhance the performance of this system for better surveillance and processing the acquired experimental data. (authors)

  5. Prototype of a simple warehouse management system based on Android mobile devices and PHP server

    OpenAIRE

    Slejko, Nejc

    2014-01-01

    This thesis presents an analysis of the competitive android applications, the process of planning and development of application system and android applications. The system will operate separately on android device and the application server, through which it will receive the information necessary for the operation. On the market there are many competing applications for storage management. Our contribution is the central storage of data and the ability to use multiple devices at once, ...

  6. Accessibility od design documentation on mobile devices with Android Operating System

    OpenAIRE

    Lovše, Tilen

    2013-01-01

    In this graduation thesis the accessibility of design documentation on mobile devices with Android operating system is discussed. Mobile devices, used for accessing to design documentation, are tablet computers or simply tablets. Introduction presents benefits of accessing to design documentation on tablets and Slovenian history in this field, followed by the review of Android operating system, its history, upgrade and features. Practical part covers the review of five different tablets, whic...

  7. Measuring channels for data transmission for on-line control systems of tokamak type thermonuclear devices

    International Nuclear Information System (INIS)

    Arsen'ev, V.A.; Bondarenko, I.M.; Gerasimov, V.P.; Repin, S.S.; Turkin, V.B.

    1982-01-01

    The experimental results are given of studying the measuring channel accuracy of automated control systems, automatic adjustment systems, interlocking and signalling control apparatus on tokamak-type devices. The diagram of the whole measuring channel is presented. It includes a measuring amplifier, a primary converter, a receiver-transmitter, secondary converters. Measurements of metrological characteristics of the measuring channels have shown that the design principles of the channels meet the measurement requarements of a tokamak device

  8. [Impact of an automated dispensing system for medical devices in cardiac surgery department].

    Science.gov (United States)

    Clou, E; Dompnier, M; Kably, B; Leplay, C; Poupon, E; Archer, V; Paul, M

    2018-01-01

    To secure medical devices' management, the implementation of automated dispensing system in surgical service has been realized. The objective of this study was to evaluate security, organizational and economic impact of installing automated dispensing system for medical devices (ASDM). The implementation took place in a cardiac surgery department. Security impact was assessed by comparing traceability rate of implantable medical devices one year before and one year after installation. Questionnaire on nurses' perception and satisfaction completed this survey. Resupplying costs, stocks' evolution and investments for the implementation of ASDM were the subject of cost-benefit study. After one year, traceability rate is excellent (100%). Nursing staffs were satisfied with 87.5% by this new system. The introduction of ASDM allowed a qualitative and quantitative decrease in stocks, with a reduction of 30% for purchased medical devices and 15% for implantable medical devices in deposit-consignment. Cost-benefit analysis shows a rapid return on investment. Real stock decrease (purchased medical devices) is equivalent to 46.6% of investment. Implementation of ASDM allows to secure storage and dispensing of medical devices. This system has also an important economic impact and appreciated by users. Copyright © 2017 Académie Nationale de Pharmacie. Published by Elsevier Masson SAS. All rights reserved.

  9. Design and Experimental Research on Venting Device for Cryostat System of EAST

    International Nuclear Information System (INIS)

    Sheng Daolin; Wu Songtao; Zhu Yinfeng

    2010-01-01

    In order to protect the cryostat system of EAST under overpressure condition,the overpressure venting device with bursting disc was designed on the cryostat system, then its type and the parameters were decided based on the ANSYS structure analysis. Furthermore, the 316LN bursting disc device was trial-manufactured based on the analytic results, and the feasibility and reliability of the design were verified through experiments. The experimental results indicate that the design is reasonable and can provide a valuable reference for the protection and research of the similar overpressure venting devices. (authors)

  10. Datacollection And Fault Tolerant Design Of Iot Devices Over A Distributed Network System

    Directory of Open Access Journals (Sweden)

    Bharadwaj Turlapati

    2017-10-01

    Full Text Available In a world where connecting and communicating with devices have never been more in need The Internet of Things thereby has a demanding need for a strategy of a design to ensure the communication between these devices is reliable maintainable and scalable. Having many permutations and combinations of possibilities of devices and solutions offered to world this paper addresses a solution with a working use case to design the system check for reliability throughput maintainability scalability and address the issues in the current system and how this design will help to overcome those issues.

  11. Structure of the main control system for the FTU device

    International Nuclear Information System (INIS)

    Panaccione, L.

    1983-01-01

    The computer based control system for FTU (Frascati Tokamak Upgrade) machine is a distributed intelligence control system consisting of various subsystems, called ''specific units''. A specific unit can work as a stand-alone small system or as a part of more complex systems, together with other units, in any possible combination. In the case of combined units working mode, a dedicated specific unit performs supervisory functions. Communication between specific units is done on a dedicated bus-like network, in the form of temporary master-slave relationship. There are three groups of specific units: Plant Control Units, Supervisory Control Unit and Synoptic Handling Unit. Performances and structures of these specific units are described. In addition, a very simple hard-wired safety system works in parallel with the computer based control system, in order to save personnel and apparatus. (author)

  12. Autonomous smart antenna systems for future mobile devices

    OpenAIRE

    Zhou, Wei

    2015-01-01

    Along with the current trend of wireless technology innovation, wideband, compact size, low-profile, lightweight and multiple functional antenna and array designs are becoming more attractive in many applications. Conventional wireless systems utilise omni-directional or sectored antenna systems. The disadvantage of such antenna systems is that the electromagnetic energy, required by a particular user located in a certain direction, is radiated unnecessarily in every direction ...

  13. Support system for loop device operator. Analysis of technological processes

    International Nuclear Information System (INIS)

    Yakovlev, V.V.; Mozhaev, A.A.; Lyadin, A.V.

    1988-01-01

    The paper presents the results obtained from the analysis of controlling the loops of a research reactor. A method of optimized interaction of the operator and hardware of the control system by computeraided identification of the cause of regime violation is considered. The equipment diagnostics based on use of the expert system methods and tuzzy algorithms enables to propose a support system for application in new generation of loops

  14. Comparative performance of passive devices for piping system under seismic excitation

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, Praveen, E-mail: pra_veen74@rediffmail.com [Bhabha Atomic Research Centre, Trombay, Mumbai, 400085 (India); Jangid, R.S. [Department of Civil Engineering, Indian Institute of Technology Bombay, Powai, Mumbai, 400076 (India); Reddy, G.R. [Bhabha Atomic Research Centre, Trombay, Mumbai, 400085 (India)

    2016-03-15

    Highlights: • Correlated the analytical results obtained from the proposed analytical procedures with experimental results in the case of XPD. • Substantial reduction of the seismic response of piping system with passive devices is observed. • Significant increase in the modal damping of the piping system is noted. • There exist an optimum parameters of the passive devices. • Good amount of energy dissipation is observed by using passive devices. - Abstract: Among several passive control devices, X-plate damper, viscous damper, visco-elastic damper, tuned mass damper and multiple tuned mass dampers are popular and used to mitigate the seismic response in the 3-D piping system. In the present paper detailed studies are made to see the effectiveness of the dampers when used in 3-D piping system subjected to artificial earthquake with increasing amplitudes. The analytical results obtained using Wen's model are compared with the corresponding experimental results available which indicated a good match with the proposed analytical procedure for the X-plate dampers. It is observed that there is significant reduction in the seismic response of interest like relative displacement, acceleration and the support reaction of the piping system with passive devices. In general, the passive devices under particular optimum parameters such as stiffness and damping are very effective and practically implementable for the seismic response mitigation, vibration control and seismic requalification of piping system.

  15. Display system architectures for digital micromirror device (DMD)-based projectors

    Science.gov (United States)

    Florence, James M.; Yoder, Lars A.

    1996-03-01

    The Digital Micromirror Device (DMDTM) developed by Texas Instruments is a highly useful Micro-Opto-Electro-Mechanical Structures (MOEMS) device that enables high quality projection display. Acting as a semiconductor light switch, the DMD can modulate incident light to produce truly digital projection display systems. Illumination and projection optics are described for three fundamental display system architectures based on the DMD light modulator. These systems include one, two, and three DMD configurations all producing full color image projection. The single device configuration implemented with a rotating color filter system represents the least system hardware while providing the capability of full color and a high brightness monochromatic mode. A two device configuration using a rotating color filter combined with a secondary color splitting filter is of particular interest when using a light source that is spectrally imbalanced. The two device configuration is also capable of a high brightness monochromatic mode of operation. The three device configuration is the most efficient with respect to light throughput considerations providing the highest brightness full color projection with the DMD light modulators. Comparisons of system performance characteristics are described indicating the features of each configuration.

  16. Hybrid optical security system using photonic crystals and MEMS devices

    Science.gov (United States)

    Ciosek, Jerzy; Ostrowski, Roman

    2017-10-01

    An important issue in security systems is that of selection of the appropriate detectors or sensors, whose sensitivity guarantees functional reliability whilst avoiding false alarms. Modern technology enables the optimization of sensor systems, tailored to specific risk factors. In optical security systems, one of the safety parameters considered is the spectral range in which the excitation signal is associated with a risk factor. Advanced safety systems should be designed taking into consideration the possible occurrence of, often multiple, complex risk factors, which can be identified individually. The hazards of concern in this work are chemical warfare agents and toxic industrial compounds present in the forms of gases and aerosols. The proposed sensor solution is a hybrid optical system consisting of a multi-spectral structure of photonic crystals associated with a MEMS (Micro Electro-Mechanical System) resonator. The crystallographic structures of carbon present in graphene rings and graphenecarbon nanotube nanocomposites have properties which make them desirable for use in detectors. The advantage of this system is a multi-spectral sensitivity at the same time as narrow-band selectivity for the identification of risk factors. It is possible to design a system optimized for detecting specified types of risk factor from very complex signals.

  17. Profilographic detection system for single-track scanning device

    International Nuclear Information System (INIS)

    Silar, J.; Kula, J.

    1988-01-01

    A profilographic detection system is claimed for diagnosing the renal function by isotope nephrography, and the bladder filling in small children and infants. The configuration described guarantees good position resolution and sensitivity of the detection system. (E.J.). 2 figs

  18. Detection device for off-gas system accidents

    International Nuclear Information System (INIS)

    Kubota, Ryuji; Tsuruoka, Ryozo; Yamanari, Shozo.

    1984-01-01

    Purpose: To rapidly isolate the off-gas system by detecting the off-gas system failure accident in a short time. Constitution: Radiation monitors are disposed to ducts connecting an exhaust gas area and an air conditioning system as a portion of a turbine building. The ducts are disposed independently such that they ventilate only the atmosphere in the exhaust gas area and do not mix the atmosphere in the turbine building. Since radioactivity issued upon off-gas accidents to the exhaust gas area is sucked to the duct, it can be detected by radiation detection monitors in a short time after the accident. Further, since the operator judges it as the off-gas system accident, the off-gas system can be isolated in a short time after the accident. (Moriyama, K.)

  19. The Evolution of Devices and Systems Supporting Rehabilitation of Lower Limbs

    Science.gov (United States)

    Olinski, M.; Lewandowski, B.; Gronowicz, A.

    2015-02-01

    This paper presents the process of development, as well as examples of devices and systems supporting rehabilitation of the human lower extremities, developed independently over the years in many parts of the world. Particular emphasis was placed on indicating, which major groups of devices supporting kinesitherapy of the lower limbs can be distinguished, what are the important advantages and disadvantages of particular types of solutions, as well as what directions currently dominating in development of rehabilitation systems may be specified. A deeper analysis and comparison of several selected systems was also conducted, resulting in gathering the outcomes in two tables. They focused on a few features of mechanical design, especially the devices' kinematic structures, and devices' additional functions associated with, among others, interaction, as well as diagnosis of the limb's state and the progress of rehabilitation.

  20. Demonstrating EnTracked a System for Energy-Efficient Position Tracking for Mobile Devices

    DEFF Research Database (Denmark)

    Kjærgaard, Mikkel Baun; Jensen, Jakob Langdal; Godsk, Torben

    An important feature of a modern mobile device is that it can position itself. Not only for use on the device but also for remote applications that require tracking of the device. To be useful, such position tracking has to be energy-efficient to avoid having a major impact on the battery life...... of the mobile device. To address this challenge we have build a system named EnTracked that, based on the estimation and prediction of system conditions and mobility, schedules position updates to both minimize energy consumption and optimize robustness. In this demonstration we would like to show how...... the system can lower the energy consumption and remain robust as pedestrians targets move around in the city center of Copenhagen....

  1. Ignitor electrode system design for the pulses electron irradiators device

    International Nuclear Information System (INIS)

    Lely Susita RM; Ihwanul Aziz

    2016-01-01

    The designed ignitor electrode system is a system used to initiate the plasma discharge. It consists of two pieces which are placed on both side of the plasma vessel. Each of the ignitor electrode system consists of a cathode, an anode and insulator between the cathode and the anode. The best cathode material for ignitor electrode system is Mg due to its lowest ion erosion rate (γi =11.7 μg/C) and its low cohesive energy (1.51 eV). The specifications of ignitor electrode system designed for the pulse electron irradiators is as follow: Mg cathode materials in the form of rod having a diameter of 6.35 mm and length of 76.75 mm. Anode material are made of non magnetic of SS 304 cylinder shaped with an outer diameter of 88.53 mm, an inner diameter of 81.53 mm and a thickness of 3.50 mm. Insulating material between the cathode and the anode is made of teflon cylinder shaped, outer diameter of 9.50 mm, an inner diameter of 6.35 mm and a length of 30 mm. Based on the ignitor electrode system design, the next step is construction and function test of the ignitor electrode system. (author)

  2. EFFICIENCY OPTIMIZATION OF ATTENDANCE SYSTEM WITH GPS AND BIOMETRIC METHOD USING MOBILE DEVICES

    Directory of Open Access Journals (Sweden)

    Benfano Soewito

    2014-05-01

    Full Text Available The existing attendance system still has drawbacks, namely the queue in front of the finger scanner, the attendance data are not integrated with Human Resources Systems, and also the employees who work outside the office cannot get in the attendance system to roll presence. In the other hand, everyone has the mobile devices and all the mobile devices will be embedded a finger scanner in the future. In this paper, it is proposed the absence system using one own device. The finger scanner and coordinate Global Position System (GPS are used as inputs for the attendance system that integrated with payroll system and human resource management tools. Application base on android platform is developed because the android is the most platforms that have been using in the most mobile devices. Using our proposed methodology, the employee can roll presence using their mobile devices and the do not need to be in queue and the employees who work outside the office also can roll presence. Research showed that proposed methodology can be used for the next generation attendance system.

  3. Improving hemodynamics of cardiovascular system under a novel intraventricular assist device support via modeling and simulations.

    Science.gov (United States)

    Zhu, Shidong; Luo, Lin; Yang, Bibo; Li, Xinghui; Wang, Xiaohao

    2017-12-01

    Ventricular assist devices (LVADs) are increasingly recognized for supporting blood circulation in heart failure patients who are non-transplant eligible. Because of its volume, the traditional pulsatile device is not easy to implant intracorporeally. Continuous flow LVADs (CF-LVADs) reduce arterial pulsatility and only offer continuous flow, which is different from physiological flow, and may cause long-term complications in the cardiovascular system. The aim of this study was to design a new pulsatile assist device that overcomes this disadvantage, and to test this device in the cardiovascular system. Firstly, the input and output characteristics of the new device were tested in a simple cardiovascular mock system. A detailed mathematical model was established by fitting the experimental data. Secondly, the model was tested in four pathological cases, and was simulated and coupled with a fifth-order cardiovascular system and a new device model using Matlab software. Using assistance of the new device, we demonstrated that the left ventricle pressure, aortic pressure, and aortic flow of heart failure patients improved to the levels of a healthy individual. Especially, in state IV level heart failure patients, the systolic blood pressure increased from 81.34 mmHg to 132.1 mmHg, whereas the diastolic blood pressure increased from 54.28 mmHg to 78.7 mmHg. Cardiac output increased from 3.21 L/min to 5.16 L/min. The newly-developed assist device not only provided a physiological flow that was similar to healthy individuals, but also effectively improved the ability of the pathological ventricular volume. Finally, the effects of the new device on other hemodynamic parameters are discussed.

  4. Reliability of Dubbed Technical Systems with Built-In Control Device

    Directory of Open Access Journals (Sweden)

    V. A. Аnischenko

    2013-01-01

    Full Text Available The paper substantiates a selection of passive or active system for dubbing technical systems in accordance with characteristics pertaining to probability of no-failure operation and mean–time-between failures with due account of non-reliability of a built-in control device and systems complexity. 

  5. 30 CFR 75.1101-16 - Dry powder chemical systems; sensing and fire-suppression devices.

    Science.gov (United States)

    2010-07-01

    ... activate the fire-control system, sound an alarm and stop the conveyor drive motor in the event of a rise... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Dry powder chemical systems; sensing and fire... Protection § 75.1101-16 Dry powder chemical systems; sensing and fire-suppression devices. (a) Each self...

  6. DC motor proportional control system for orthotic devices

    Science.gov (United States)

    Blaise, H. T.; Allen, J. R.

    1972-01-01

    Multi-channel proportional control system for operation of dc motors for use with externally-powered orthotic arm braces is described. Components of circuitry and principles of operation are described. Schematic diagram of control circuit is provided.

  7. Lithographically-Scribed Planar Holographic Optical CDMA Devices and Systems

    National Research Council Canada - National Science Library

    Mossberg, Thomas

    2007-01-01

    .... The present Phase II effort has harnessed new fabrication tools to perfect disruptive HBR-based multiplexer products for DoD avionics, optical communications systems computer data communications and local area networks...

  8. 46 CFR 62.25-25 - Programable systems and devices.

    Science.gov (United States)

    2010-10-01

    ..., alarm, and monitoring systems must be stored in non-volatile memory and automatically operate on supply... to be aboard the vessel must not be stored in electronic or magnetic memory. [CGD 81-030, 53 FR 17838...

  9. Unmanned Aerial System Four-Dimensional Gunnery Training Device Development

    Science.gov (United States)

    2017-10-01

    Operator program of instruction. 15. SUBJECT TERMS Gray Eagle Unmanned Aerial System Training; 4D Visualization Training; Airspace...for operators of the Shadow and Gray Eagle1 (referred to as GE from this point forward) systems occurs at Fort Huachuca, Arizona in the 2-13th...space and seeing it through their cockpit windows . On the other hand, UAS operators are limited to the stovepipe view from the aircraft payload and

  10. Double deflection system for an electron beam device

    International Nuclear Information System (INIS)

    Parker, N.W.; Crewe, A.V.

    1978-01-01

    A double deflection scanning system for electron beam instruments is provided embodying a means of correcting isotropic coma, and anisotropic coma aberrations induced by the magnetic lens of such an instrument. The scanning system deflects the beam prior to entry into the magnetic lens from the normal on-axis intersection of the beam with the lens according to predetermined formulas and thereby reduces the aberrations

  11. Development of 14' x 8.5' active matrix flat-panel digital x-ray detector system and imaging performance

    International Nuclear Information System (INIS)

    Park, Ji Koon; Choi, Jang Yong; Kang, Sang Sik; Lee, Dong Gil; Seok, Dae Woo; Nam, Sang Hee

    2003-01-01

    Digital radiographic systems based on solid-state detectors, commonly referred to as flat-panel detectors, are gaining popularity in clinical practice. Large area, flat panel solid state detectors are being investigated for digital radiography. The purpose of this work was to evaluate the active matrix flat panel digital x-ray detectors in terms or their modulation transfer function (MTF), noise power spectrum (NPS), and detective quantum efficiency (DQE). In this paper, development and evaluation of a selenium-based flat-panel digital x-ray detector are described. The prototype detector has a pixel pitch of 139 μ m and a total active imaging area of 14 x 8.5 inch 2 giving a total 3.9 million pixels. This detector include a x-ray imaging layer of amorphous selenium as a photoconductor which is evaporated in vacuum state on a TFT flat panel, to make signals in proportion to incident x-ray. The film thickness was about 500 μ m. To evaluate the imaging performance of the digital radiography (DR) system developed in our group, sensitivity, linearity, the modulation transfer function (MTF), noise power spectrum (NPS) and detective quantum efficiency (DQE) of detector was measured. The measured sensitivity was 4.16 x 10 6 ehp/pixel·mR at the bias field of 10 V/ μ m: The beam condition was 41.9 KeV. Measured MTF at 2.5 lp/mm was 52%, and the DQE at 1.5 lp/mm was 75%. And the excellent linearity was showed where the coefficient of determination (r 2 ) is 0.9693

  12. Development of 14' x 8.5' active matrix flat-panel digital x-ray detector system and imaging performance

    Energy Technology Data Exchange (ETDEWEB)

    Park, Ji Koon; Choi, Jang Yong; Kang, Sang Sik; Lee, Dong Gil; Seok, Dae Woo; Nam, Sang Hee [Medical Imaging Research Center of Inje Univeristy, Kimhae (Korea, Republic of)

    2003-12-15

    Digital radiographic systems based on solid-state detectors, commonly referred to as flat-panel detectors, are gaining popularity in clinical practice. Large area, flat panel solid state detectors are being investigated for digital radiography. The purpose of this work was to evaluate the active matrix flat panel digital x-ray detectors in terms or their modulation transfer function (MTF), noise power spectrum (NPS), and detective quantum efficiency (DQE). In this paper, development and evaluation of a selenium-based flat-panel digital x-ray detector are described. The prototype detector has a pixel pitch of 139 {mu} m and a total active imaging area of 14 x 8.5 inch{sup 2} giving a total 3.9 million pixels. This detector include a x-ray imaging layer of amorphous selenium as a photoconductor which is evaporated in vacuum state on a TFT flat panel, to make signals in proportion to incident x-ray. The film thickness was about 500 {mu} m. To evaluate the imaging performance of the digital radiography (DR) system developed in our group, sensitivity, linearity, the modulation transfer function (MTF), noise power spectrum (NPS) and detective quantum efficiency (DQE) of detector was measured. The measured sensitivity was 4.16 x 10{sup 6} ehp/pixel{center_dot}mR at the bias field of 10 V/ {mu} m: The beam condition was 41.9 KeV. Measured MTF at 2.5 lp/mm was 52%, and the DQE at 1.5 lp/mm was 75%. And the excellent linearity was showed where the coefficient of determination (r{sup 2}) is 0.9693.

  13. A prompt information retrieval system on handheld devices

    Science.gov (United States)

    Huang, Yo-Ping; Yen, Wei; Lin, Shi-Hung

    2007-04-01

    In this paper, we propose an intelligent bird information retrieval system which aims to construct a mobility-learning activity under the up-to-date wireless technology. The system consists of a Tablet PC and PDAs with wireless networking capabilities. The PDA is equipped with a friendly retrieval interface and a good learning environment. In our system, users only need to click the buttons or input the keywords to retrieve bird information. Besides, users can discuss or share their information and knowledge via the wireless network. Our system saves bird information in four categories including "Introduction," "Images," "Sound," "Streaming Media," and "Ecological Memo." The integral knowledge helps users understand more about birds. Data mining and fuzzy association rules are applied to recommend users those birds they may be interested in. A streaming server on the Tablet PC is built to provide the streaming media for PDA users. By this way, PDA users can enjoy the multimedia from Tablet PC in real time without downloading completely. Finally, the system is a perfect tool for outdoor teaching and can be easily extended to provide navigation and touring services for national parks or museums.

  14. [Web-based support system for medical device maintenance].

    Science.gov (United States)

    Zhao, Jinhai; Hou, Wensheng; Chen, Haiyan; Tang, Wei; Wang, Yihui

    2015-01-01

    A Web-based technology system was put forward aiming at the actual problems of the long maintenance cycle and the difficulties of the maintenance and repairing of medical equipments. Based on analysis of platform system structure and function, using the key technologies such as search engine, BBS, knowledge base and etc, a platform for medical equipment service technician to use by online or offline was designed. The platform provides users with knowledge services and interactive services, enabling users to get a more ideal solution.

  15. Reactor-Capaсitor Device for Flexible Link Between Non-Synchronous Power Systems

    Directory of Open Access Journals (Sweden)

    Bosneaga V.

    2016-04-01

    Full Text Available In present flexible interconnections for transmission of required active power between different power systems is used, as a rule, so-called DC back-to-back link. The aim of this work is the investigation of proposed reactor-capacitor device for flexible connection of asynchronously alternating current power systems with the same nominal values of frequencies for parallel operation. The reactor-capacitor device was elaborated. The installation develops the idea of controlled reactor alternating current link, and provides reactive power balance in the unit and needed value of the output voltage module. The basic characteristics of reactor-capacitor device for controlled power transmission were investigated. Analytical expressions for device elements parameters were derived. These ensure necessary ratio of voltages modules of linked power systems and reactive power balance of the device at circular output voltage vector rotation for a given load admittance. Obtained parameters ensure constant active power flow between linked asynchronously power systems and device reactive power internal balance.

  16. Measurement of effective detective quantum efficiency for a photon counting scanning mammography system and comparison with two flat panel full-field digital mammography systems

    Science.gov (United States)

    Wood, Tim J.; Moore, Craig S.; Saunderson, John R.; Beavis, Andrew W.

    2018-01-01

    Effective detective quantum efficiency (eDQE) describes the resolution and noise properties of an imaging system along with scatter and primary transmission, all measured under clinically appropriate conditions. Effective dose efficiency (eDE) is the eDQE normalised to mean glandular dose and has been proposed as a useful metric for the optimisation of clinical imaging systems. The aim of this study was to develop a methodology for measuring eDQE and eDE on a Philips microdose mammography (MDM) L30 photon counting scanning system, and to compare performance with two conventional flat panel systems. A custom made lead-blocker was manufactured to enable the accurate determination of dose measurements, and modulation transfer functions were determined free-in-air at heights of 2, 4 and 6 cm above the breast support platform. eDQE were calculated for a Philips MDM L30, Hologic Dimensions and Siemens Inspiration digital mammography system for 2, 4 and 6 cm thick poly(methyl methacrylate) (PMMA). The beam qualities (target/filter and kilovoltage) assessed were those selected by the automatic exposure control, and anti-scatter grids were used where available. Measurements of eDQE demonstrate significant differences in performance between the slit- and scan-directions for the photon counting imaging system. MTF has been shown to be the limiting factor in the scan-direction, which results in a rapid fall in eDQE at mid-to-high spatial frequencies. A comparison with two flat panel mammography systems demonstrates that this may limit image quality for small details, such as micro-calcifications, which correlates with a more conventional image quality assessment with the CDMAM phantom. eDE has shown the scanning photon counting system offers superior performance for low spatial frequencies, which will be important for the detection of large low contrast masses. Both eDQE and eDE are proposed as useful metrics that should enable optimisation of the Philips MDM L30.

  17. A general device driver simulator to help compare real time control systems

    International Nuclear Information System (INIS)

    Mohan, M.

    2012-01-01

    Supervisory Control And Data Acquisition systems (SCADA) such as Epics, Tango and Tine usually provide small example device driver programs for testing or to help users get started, however they differ between systems making it hard to compare the SCADA. To address this, a small simulator driver was created which emulates signals and errors similar to those received from a hardware device. The simulator driver can return from one to four signals: a ramp signal, a large alarm ramp signal, an error signal and a time-out. The different signals or errors are selected using the associated software device number. The simulator driver performs similar functions to Epic's clockApp, Tango's TangoTest and the Tine's sine-generator but the signals are independent of the SCADA. A command line application, an Epics server (IOC), a Tango device server, and a Tine server (FEC) were created and linked with the simulator driver. In each case the software device numbers were equated to a dummy device. Using the servers it was possible to compare how each SCADA behaved against the same repeatable signals. In addition to comparing and testing the SCADA the finished servers proved useful as templates for real hardware device drivers. (author)

  18. A review of fusion device fuel cleanup systems

    International Nuclear Information System (INIS)

    Dombra, A.H.; Carney, M.

    1984-01-01

    Design options for a small fusion fuel purification system are assessed by comparing six conceptual system designs based on one of the following: (1) a Zr/Al getter pump for in vacuo applications, (2) a cryogenic molecular sieve adsorber at 77K, (3) a palladium-alloy membrane diffuser, (4) a U-bed reactor at 1170K, (5) a two-compartment cryogenic freezer at 27-50K and 50-300K, and (6) a U-bed and non-regenerative Zr/Al gas purifier. The preferred system (6) introduces a new concept of fuel purification based on well-established techniques: recovery of purified D 2 -DR-T 2 from a helium carrier gas with the U-bed, followed by the removal of impurities from the carrier gas with the non-regenerative Zr/Al gas purifier. The main advantages of this system are simplicity, safety and relatively small quantity of tritiated waste produced by the process. The tritium in the waste is immobilized as a stable tritide of Zr/Al. (author)

  19. Data base management system configuration specification. [computer storage devices

    Science.gov (United States)

    Neiers, J. W.

    1979-01-01

    The functional requirements and the configuration of the data base management system are described. Techniques and technology which will enable more efficient and timely transfer of useful data from the sensor to the user, extraction of information by the user, and exchange of information among the users are demonstrated.

  20. System Control Device Electronics Smart Home Using Neural Networks

    Directory of Open Access Journals (Sweden)

    Safarul Ilham

    2017-06-01

    Full Text Available The use of information technology is very useful for today’s life and the next, where the human facilitated in doing a variety of activities in the life day to day. By the development of the existing allows people no longer do a job with difficulty. For that, it takes a system safety home using system technology Web-based and complete video streaming CCTV (video streaming a person can see the condition of his home whenever and wherever by using handphone, laptops and other tools are connected to the Internet network. This tool can facilitate someone in the monitor at home and control equipment the House as open and close and the lock the gate, turning on and off the lights so homeowners are no longer have to visit their home and fear the state of the House because fully security and control in the House was handled by the system. based on the above problems Writer try to design work system a tool that can control the simulation tools home using two Microcontroller is Attiny 2313 and Atmega16.

  1. Application of energy storage devices in power systems

    African Journals Online (AJOL)

    user

    Abstract. In Electric Power systems, power quality has been one of the issues of increasing interests. Energy storage does not mean just the energy sources but they also provide the added benefits of improving power quality, dynamic and transient stability and also the reliability of the supply. Some of the major ...

  2. Energy Systems Integration: Demonstrating the Grid Benefits of Connected Devices

    Energy Technology Data Exchange (ETDEWEB)

    2017-01-01

    Overview fact sheet about the Electric Power Research Institute (EPRI) and the University of Delaware Integrated Network Testbed for Energy Grid Research and Technology Experimentation (INTEGRATE) project at the Energy Systems Integration Facility. INTEGRATE is part of the U.S. Department of Energy's Grid Modernization Initiative.

  3. PMJ panel discussion overview on mask complexities, cost, and cycle time in 32-nm system LSI generation: conflict or concurrent?

    Science.gov (United States)

    Hosono, Kunihiro; Kato, Kokoro

    2008-10-01

    This is a report on a panel discussion organized in Photomask Japan 2008, where the challenges about "Mask Complexities, Cost, and Cycle Time in 32-nm System LSI Generation" were addressed to have a look over the possible solutions from the standpoints of chipmaker, commercial mask shop, DA tool vendor and equipments makers. The wrap-up is as follows: Mask complexities justify the mask cost, while the acceptable increase rate of 32nm-mask cost significantly differs between mask suppliers or users side. The efficiency progress by new tools or DFM has driven their cycle-time reductions. Mask complexities and cost will be crucial issues prior to cycle time, and there seems to be linear correlation between them. Controlling complexity and cycle time requires developing a mix of advanced technologies, and especially for cost reduction, shot prices in writers and processing rates in inspection tools have been improved remarkably by tool makers. In addition, activities of consortium in Japan (Mask D2I) are expected to enhance the total optimization of mask design, writing and inspection. The cycle-time reduction potentially drives the lowering of mask cost, and, on the other, the pattern complexities and tighter mask specifications get in the way to 32nm generation as well as the nano-economics and market challenges. There are still many difficult problems in mask manufacturing now, and we are sure to go ahead to overcome a 32nm hurdle with the advances of technologies and collaborations by not only technologies but also finance.

  4. System Testability Analysis for Complex Electronic Devices Based on Multisignal Model

    International Nuclear Information System (INIS)

    Long, B; Tian, S L; Huang, J G

    2006-01-01

    It is necessary to consider the system testability problems for electronic devices during their early design phase because modern electronic devices become smaller and more compositive while their function and structure are more complex. Multisignal model, combining advantage of structure model and dependency model, is used to describe the fault dependency relationship for the complex electronic devices, and the main testability indexes (including optimal test program, fault detection rate, fault isolation rate, etc.) to evaluate testability and corresponding algorithms are given. The system testability analysis process is illustrated for USB-GPIB interface circuit with TEAMS toolbox. The experiment results show that the modelling method is simple, the computation speed is rapid and this method has important significance to improve diagnostic capability for complex electronic devices

  5. EFSA NDA Panel (EFSA Panel on Dietetic Products, Nutrition and Allergies ), 2015. Scientific opinion on vitamin D and contribution to the normal function of the immune system: evaluation of a health claim pursuant to Article14 of Regulation (EC) No 1924/2006

    DEFF Research Database (Denmark)

    Tetens, Inge

    2015-01-01

    Following an application from Specialised Nutrition Europe (formerly IDACE), submitted for authorisation of a health claim pursuant to Article 14 of Regulation (EC) No 1924/2006 via the Competent Authority of France, the EFSA Panel on Dietetic Products, Nutrition and Allergies (NDA) was asked...... to deliver an opinion on the scientific substantiation of a health claim related to vitamin D and its contribution to the normal function of the immune system. The Panel considers that vitamin D is sufficiently characterised. A contribution to the normal function of the immune system is a beneficial...... physiological effect. The Panel has previously assessed claims on vitamin D and its contribution to the normal function of the immune system with favourable outcomes. The target populations were the general population and children aged 3 to 18 years. The Panel considers that the role of vitamin D...

  6. A Compact Energy Harvesting System for Outdoor Wireless Sensor Nodes Based on a Low-Cost In Situ Photovoltaic Panel Characterization-Modelling Unit.

    Science.gov (United States)

    Antolín, Diego; Medrano, Nicolás; Calvo, Belén; Martínez, Pedro A

    2017-08-04

    This paper presents a low-cost high-efficiency solar energy harvesting system to power outdoor wireless sensor nodes. It is based on a Voltage Open Circuit (VOC) algorithm that estimates the open-circuit voltage by means of a multilayer perceptron neural network model trained using local experimental characterization data, which are acquired through a novel low cost characterization system incorporated into the deployed node. Both units-characterization and modelling-are controlled by the same low-cost microcontroller, providing a complete solution which can be understood as a virtual pilot cell, with identical characteristics to those of the specific small solar cell installed on the sensor node, that besides allows an easy adaptation to changes in the actual environmental conditions, panel aging, etc. Experimental comparison to a classical pilot panel based VOC algorithm show better efficiency under the same tested conditions.

  7. Independent peer review panel report on the integrated nonthermal treatment systems study and the comparison of integrated thermal and integrated nonthermal treatment systems for mixed low level waste

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-08-01

    The US Department of Energy`s (DOE) Office of Environmental Management (EM) Office of Science and Technology (OST) has conducted studies of integrated thermal treatment systems and integrated nonthermal treatment systems (INTS) for treating contact handled, alpha and non-alpha mixed low level radioactive waste (MLLW). The MLLW in the DOE complex consists of a wide variety of organic and inorganic solids and liquids contaminated with radioactive substances. Treatment systems are needed to destroy organic material and stabilize residues prior to land disposal. In May 1996 the Deputy Assistant Secretary for OST appointed an Independent Peer Review Panel to: (1) review and comment on the INTS Study; (2) make recommendations on the most promising thermal and nonthermal treatment systems; (3) make recommendations on research and development necessary to prove the performance of nonthermal and thermal technologies; and (4) review and comment on the preliminary draft of the ITTS/INTS Comparison Report. This report presents the primary conclusions and recommendations based on the review of the INTS study and the comparison report. System selection, overviews, comparisons, cost estimations and sensitivity analyses, and recommended R and D engineering needs are then described and discussed.

  8. Independent peer review panel report on the integrated nonthermal treatment systems study and the comparison of integrated thermal and integrated nonthermal treatment systems for mixed low level waste

    International Nuclear Information System (INIS)

    1996-08-01

    The US Department of Energy's (DOE) Office of Environmental Management (EM) Office of Science and Technology (OST) has conducted studies of integrated thermal treatment systems and integrated nonthermal treatment systems (INTS) for treating contact handled, alpha and non-alpha mixed low level radioactive waste (MLLW). The MLLW in the DOE complex consists of a wide variety of organic and inorganic solids and liquids contaminated with radioactive substances. Treatment systems are needed to destroy organic material and stabilize residues prior to land disposal. In May 1996 the Deputy Assistant Secretary for OST appointed an Independent Peer Review Panel to: (1) review and comment on the INTS Study; (2) make recommendations on the most promising thermal and nonthermal treatment systems; (3) make recommendations on research and development necessary to prove the performance of nonthermal and thermal technologies; and (4) review and comment on the preliminary draft of the ITTS/INTS Comparison Report. This report presents the primary conclusions and recommendations based on the review of the INTS study and the comparison report. System selection, overviews, comparisons, cost estimations and sensitivity analyses, and recommended R and D engineering needs are then described and discussed

  9. Gore excluder device with the C3 delivery system for management of abdominal aortic aneurysm

    OpenAIRE

    Morasch, Mark; Cheong J. Lee,; Mark L. Keldahl,

    2012-01-01

    Cheong J Lee, Mark L Keldahl, Mark D MoraschDivision of Vascular Surgery, Northwestern University Feinberg School of Medicine, Chicago, IL, USAAbstract: The GORE Excluder stent-graft is one of the currently available devices approved by the US Food and Drug Administration for use in endovascular aortic repair. Recently, a new delivery system modification has been applied to the Excluder device which allows repositioning of the stent-graft to adjust for accurate proximal landing and facilitate...

  10. Conceptual design report for a Fusion Engineering Device sector-handling machine and movable manipulator system

    International Nuclear Information System (INIS)

    Watts, K.D.; Masson, L.S.; McPherson, R.S.

    1982-10-01

    Design requirements, trade studies, design descriptions, conceptual designs, and cost estimates have been completed for the Fusion Engineering Device sector handling machine, movable manipulator system, subcomponent handling machine, and limiter blade handling machine. This information will be used by the Fusion Engineering Design Center to begin to determine the cost and magnitude of the effort required to perform remote maintenance on the Fusion Engineering Device. The designs presented are by no means optimum, and the costs estimates are rough-order-of-magnitude

  11. Terahertz and Microwave Devices Based on the Photo-Excited Low Dimensional Electronic System

    Science.gov (United States)

    2015-03-11

    2010 12-Nov-2014 Approved for Public Release; Distribution Unlimited Final Report: Continuation: Terahertz and Microwave Devices Based on the Photo...NAME(S) AND ADDRESS (ES) U.S. Army Research Office P.O. Box 12211 Research Triangle Park, NC 27709-2211 Terahertz , Microwaves, 2 Dimensional... Terahertz and Microwave Devices Based on the Photo-Excited Low Dimensional Electronic System Report Title This experimental project funded by the ARO

  12. Fabrication of polystyrene microfluidic devices using a pulsed CO2 laser system

    KAUST Repository

    Li, Huawei

    2013-10-10

    In this article, we described a simple and rapid method for fabrication of droplet microfluidic devices on polystyrene substrate using a CO2 laser system. The effects of the laser power and the cutting speed on the depth, width and aspect ratio of the microchannels fabricated on polystyrene were investigated. The polystyrene microfluidic channels were encapsulated using a hot press bonding technique. The experimental results showed that both discrete droplets and laminar flows could be obtained in the device.

  13. Ontology-Driven Instant Messaging-Based Dialogue System for Device Control

    KAUST Repository

    Noguera-Arnaldos, José Ángel

    2015-10-14

    The im4Things platform aims to develop a communication interface for devices in the Internet of the Things (IoT) through intelligent dialogue based on written natural language over instant messaging services. This type of communication can be established in different ways such as order sending and, status querying. Also, the devices themselves are responsible for alerting users when a change has been produced in the device’s sensors. The system has been validated and it has obtained promising results.

  14. Constructing the informatics and information technology foundations of a medical device evaluation system: a report from the FDA unique device identifier demonstration.

    Science.gov (United States)

    Drozda, Joseph P; Roach, James; Forsyth, Thomas; Helmering, Paul; Dummitt, Benjamin; Tcheng, James E

    2018-02-01

    The US Food and Drug Administration (FDA) has recognized the need to improve the tracking of medical device safety and performance, with implementation of Unique Device Identifiers (UDIs) in electronic health information as a key strategy. The FDA funded a demonstration by Mercy Health wherein prototype UDIs were incorporated into its electronic information systems. This report describes the demonstration's informatics architecture. Prototype UDIs for coronary stents were created and implemented across a series of information systems, resulting in UDI-associated data flow from manufacture through point of use to long-term follow-up, with barcode scanning linking clinical data with UDI-associated device attributes. A reference database containing device attributes and the UDI Research and Surveillance Database (UDIR) containing the linked clinical and device information were created, enabling longitudinal assessment of device performance. The demonstration included many stakeholders: multiple Mercy departments, manufacturers, health system partners, the FDA, professional societies, the National Cardiovascular Data Registry, and information system vendors. The resulting system of systems is described in detail, including entities, functions, linkage between the UDIR and proprietary systems using UDIs as the index key, data flow, roles and responsibilities of actors, and the UDIR data model. The demonstration provided proof of concept that UDIs can be incorporated into provider and enterprise electronic information systems and used as the index key to combine device and clinical data in a database useful for device evaluation. Keys to success and challenges to achieving this goal were identified. Fundamental informatics principles were central to accomplishing the system of systems model. © The Author 2017. Published by Oxford University Press on behalf of the American Medical Informatics Association. All rights reserved. For Permissions, please email: journals.permissions@oup.com

  15. A simple and highly stable free-flow electrophoresis device with thermoelectric cooling system.

    Science.gov (United States)

    Yan, Jian; Guo, Cheng-Gang; Liu, Xiao-Ping; Kong, Fan-Zhi; Shen, Qiao-Yi; Yang, Cheng-Zhang; Li, Jun; Cao, Cheng-Xi; Jin, Xin-Qiao

    2013-12-20

    Complex assembly, inconvenient operations, poor control of Joule heating and leakage of solution are still fundamental issues greatly hindering application of free-flow electrophoresis (FFE) for preparative purpose in bio-separation. To address these issues, a novel FFE device was developed based on our previous work. Firstly, a new mechanical structure was designed for compact assembly of separation chamber, fast removal of air bubble, and good anti-leakage performance. Secondly, a highly efficient thermoelectric cooling system was used for dispersing Joule heating for the first time. The systemic experiments revealed the three merits: (i) 3min assembly without any liquid leakage, 80 times faster than pervious FFE device designed by us or commercial device (4h); (ii) 5s removing of air bubble in chamber, 1000-fold faster than a normal one (2h or more) and (iii) good control of Joule heating by the cooling system. These merits endowed the device high stable thermo- and hydro-dynamic flow for long-term separation even under high electric field of 63V/cm. Finally, the developed device was used for up to 8h continuous separation of 5mg/mL fuchsin acid and purification of three model proteins of phycocyanin, myoglobin and cytochrome C, demonstrating the applicability of FFE. The developed FFE device has evident significance to the studies on stem cell, cell or organelle proteomics, and protein complex as well as micro- or nano-particles. Copyright © 2013 Elsevier B.V. All rights reserved.

  16. Positioning device for MRI-guided high intensity focused ultrasound system

    Energy Technology Data Exchange (ETDEWEB)

    Damianou, Christakis [Frederick Institute of Technology (FIT), Limassol (Cyprus); MEDSONIC, LTD, Limassol (Cyprus); Ioannides, Kleanthis [Polikliniki Igia, Limassol (Cyprus); Milonas, Nicos [Frederick Institute of Technology (FIT), Limassol (Cyprus)

    2008-04-15

    A prototype magnetic resonance imaging (MRI)- compatible positioning device was used to move an MRI-guided high intensity focused ultrasound (HIFU) transducer. The positioning device has three user-controlled degrees of freedom that allow access to various targeted lesions. The positioning device was designed and fabricated using construction materials selected for compatibility with high magnetic fields and fast switching magnetic field gradients encountered inside MRI scanners. The positioning device incorporates only MRI compatible materials such as piezoelectric motors, plastic sheets, brass screws, plastic pulleys and timing belts. The HIFU/MRI system includes the multiple subsystems (a) HIFU system, (b) MR imaging, (c) Positioning device (robot) and associate drivers, (d) temperature measurement, (e) cavitation detection, (f) MRI compatible camera, and (g) Soft ware. The MRI compatibility of the system was successfully demonstrated in a clinical high-field MRI scanner. The ability of the robot to accurately move the transducer thus creating discrete and overlapping lesions in biological tissue was tested successfully. A simple, cost effective, portable positioning device has been developed which can be used in virtually any clinical MRI scanner since it can be sited on the scanner's table. The propagation of HIFU can use either a lateral or superior-inferior approach. Discrete and large lesions were created successfully with reproducible results. (orig.)

  17. Security analysis on some experimental quantum key distribution systems with imperfect optical and electrical devices

    Science.gov (United States)

    Liang, Lin-Mei; Sun, Shi-Hai; Jiang, Mu-Sheng; Li, Chun-Yan

    2014-10-01

    In general, quantum key distribution (QKD) has been proved unconditionally secure for perfect devices due to quantum uncertainty principle, quantum noncloning theorem and quantum nondividing principle which means that a quantum cannot be divided further. However, the practical optical and electrical devices used in the system are imperfect, which can be exploited by the eavesdropper to partially or totally spy the secret key between the legitimate parties. In this article, we first briefly review the recent work on quantum hacking on some experimental QKD systems with respect to imperfect devices carried out internationally, then we will present our recent hacking works in details, including passive faraday mirror attack, partially random phase attack, wavelength-selected photon-number-splitting attack, frequency shift attack, and single-photon-detector attack. Those quantum attack reminds people to improve the security existed in practical QKD systems due to imperfect devices by simply adding countermeasure or adopting a totally different protocol such as measurement-device independent protocol to avoid quantum hacking on the imperfection of measurement devices [Lo, et al., Phys. Rev. Lett., 2012, 108: 130503].

  18. Miniaturized supercapacitors: key materials and structures towards autonomous and sustainable devices and systems

    Science.gov (United States)

    Soavi, Francesca; Bettini, Luca Giacomo; Piseri, Paolo; Milani, Paolo; Santoro, Carlo; Atanassov, Plamen; Arbizzani, Catia

    2016-09-01

    Supercapacitors (SCs) are playing a key role for the development of self-powered and self-sustaining integrated systems for different fields ranging from remote sensing, robotics and medical devices. SC miniaturization and integration into more complex systems that include energy harvesters and functional devices are valuable strategies that address system autonomy. Here, we discuss about novel SC fabrication and integration approaches. Specifically, we report about the results of interdisciplinary activities on the development of thin, flexible SCs by an additive technology based on Supersonic Cluster Beam Deposition (SCBD) to be implemented into supercapacitive electrolyte gated transistors and supercapacitive microbial fuel cells. Such systems integrate at materials level the specific functions of devices, like electric switch or energy harvesting with the reversible energy storage capability. These studies might open new frontiers for the development and application of new multifunction-energy storage elements.

  19. Performance evaluation of propulsion systems as LEO deorbiting devices

    Directory of Open Access Journals (Sweden)

    Alexandru IONEL

    2017-09-01

    Full Text Available This paper evaluates the possibility of deorbiting a launch vehicle upper-stage at end-of-mission from low Earth orbit, by using an additional propulsion system as a means of achieving deorbiting and complying with the “25 years” mitigation regulation. The deorbiting performances of chemical and electrical propulsion are analyzed through a MATLAB code which integrates orbital perturbations such as gravitational acceleration, atmospheric drag and rocket engine/motor thrust. Additionally, the research is placed within a body of similar papers concerned with deorbiting by means of propulsion, by performing a state of the art study.

  20. Microscale mass spectrometry systems, devices and related methods

    Energy Technology Data Exchange (ETDEWEB)

    Ramsey, John Michael

    2017-04-11

    Mass spectrometry systems or assemblies therefore include an ionizer that includes at least one planar conductor, a mass analyzer with a planar electrode assembly, and a detector comprising at least one planar conductor. The ionizer, the mass analyzer and the detector are attached together in a compact stack assembly. The stack assembly has a perimeter that bounds an area that is between about 0.01 mm.sup.2 to about 25 cm.sup.2 and the stack assembly has a thickness that is between about 0.1 mm to about 25 mm.

  1. Using event-B for critical device software systems

    CERN Document Server

    Singh, Neeraj Kumar

    2013-01-01

    Defining a new development life-cycle methodology, together with a set of associated techniques and tools to develop highly critical systems using formal techniques, this book adopts a rigorous safety assessment approach explored via several layers (from requirements analysis to automatic source code generation). This is assessed and evaluated via a standard case study: the cardiac pacemaker. Additionally a formalisation of an Electrocardiogram (ECG) is used to identify anomalies in order to improve existing medical protocols. This allows the key issue - that formal methods are not currently i

  2. Developing a HACCP-like system for improving animal health and welfare in organic egg production - based on an expert panel analysis.

    Science.gov (United States)

    Hegelund, L; Sørensen, J T

    2007-08-01

    In the process of developing a generic Hazard Analysis and Critical Control Point (HACCP)-like system for securing animal health and welfare in organic egg production, an expert panel analysis was used to perform the initial hazard analysis. Eighteen advisers and researchers in organic egg production were included in the expert panel. In a series of four questionnaires, the expert panel first scored 34 health and welfare problems seen in Danish organic egg production. Based on scorings of severity and occurrence, 10 problems were selected for further analysis. The experts subsequently suggested and scored risk factors for those problems and finally suggested control points, alarm values indicating the need for corrective actions in order to control the risk factors and monitoring frequencies of these. The 10 selected problems were hunger, thirst, piling, crop impaction, blackhead, pasteurellosis, bone fractures, cannibalism, predators and red mites. A total of 154 different risk factors were suggested for these problems. The 41 risk factors which rated highest in a combined scoring of importance and occurrence were selected for further analysis. There was a high degree of consensus between experts when scoring both problems and risk factors. The level of consensus, as defined by an interquartile range 1, was 79% to 100% when scoring the health and welfare problems (scale 1-5) and 77% to 95% when scoring the risk factors (scale 1-4). On average, 5.8 control points were suggested for every risk factor. Alarm values were often not detailed enough to be of practical significance and further analysis is needed in order to define these. The experts were highly diverse in their suggested monitoring frequencies and establishment of monitoring schemes should be part of developing the farm specific systems. An expert panel analysis based on questionnaires was a useful tool during the first steps of developing a HACCP plan, conducting a hazard analysis and suggesting control

  3. Unified Haptic System Using Three Kinds of Cutting Devices for the Basic Use of Medical Application

    Science.gov (United States)

    Honma, Satoru; Wakamatsu, Hidetoshi

    Most training simulators of surgery have simply required manipulation of organic models with their deformation by a single operating device. In order to operate them by various kinds of operating devices, we hereby propose a new type of force-display system based on the combination of the haptic cutting systems of knife, scissors and saw, considering the dynamics of cutting operation of materials mathematically analyzed from their corresponding physical viewpoints. The proposed system is well confirmed to represent the dynamic deformation of virtual objects during their operation inclusive of their incidental cutting force.

  4. Implications for a Wireless, External Device System to Study Electrocorticography

    Directory of Open Access Journals (Sweden)

    David Rotermund

    2017-04-01

    Full Text Available Implantable neuronal interfaces to the brain are an important keystone for future medical applications. However, entering this field of research is difficult since such an implant requires components from many different areas of technology. Since the complete avoidance of wires is important due to the risk of infections and other long-term problems, means for wirelessly transmitting data and energy are a necessity which adds to the requirements. In recent literature, many high-tech components for such implants are presented with remarkable properties. However, these components are typically not freely available for such a system. Every group needs to re-develop their own solution. This raises the question if it is possible to create a reusable design for an implant and its external base-station, such that it allows other groups to use it as a starting point. In this article, we try to answer this question by presenting a design based exclusively on commercial off-the-shelf components and studying the properties of the resulting system. Following this idea, we present a fully wireless neuronal implant for simultaneously measuring electrocorticography signals at 128 locations from the surface of the brain. All design files are available as open source.

  5. MEMS- and NEMS-based complex adaptive smart devices and systems

    Science.gov (United States)

    Varadan, Vijay K.

    2001-10-01

    The microelectronics industry has seen explosive growth during the last thirty years. Extremely large markets for logic and memory devices have driven the development of new materials, and technologies for the fabrication of even more complex devices with feature sizes now down at the sub micron and nanometer level. Recent interest has arisen in employing these materials, tools and technologies for the fabrication of miniature sensors and actuators and their integration with electronic circuits to produce smart devices and systems. This effort offers the promise of: 1) increasing the performance and manufacturability of both sensors and actuators by exploiting new batch fabrication processes developed including micro stereo lithographic and micro molding techniques; 2) developing novel classes of materials and mechanical structures not possible previously, such as diamond like carbon, silicon carbide and carbon nanotubes, micro-turbines and micro-engines; 3) development of technologies for the system level and wafer level integration of micro components at the nanometer precision, such as self-assembly techniques and robotic manipulation; 4) development of control and communication systems for MEMS devices, such as optical and RF wireless, and power delivery systems, etc. A novel composite structure can be tailored by functionalizing carbon nanotubes and chemically bonding them with the polymer matrix e.g. block or graft copolymer, or even cross-linked copolymer, to impart exceptional structural, electronic and surface properties. Bio- and mechanical-MEMS devices derived from this hybrid composite provide a new avenue for future smart systems.

  6. An easy-to-use microfluidic interconnection system to create quick and reversibly interfaced simple microfluidic devices

    DEFF Research Database (Denmark)

    Pfreundt, Andrea; Andersen, Karsten Brandt; Dimaki, Maria

    2015-01-01

    The presented microfluidic interconnection system provides an alternative for the individual interfacing of simple microfluidic devices fabricated in polymers such as polymethylmethacrylate, polycarbonate and cyclic olefin polymer. A modification of the device inlet enables the direct attachment...

  7. ATCA Shelf Manager EPICS device support for ITER CODAC Core System

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Bruno, E-mail: bsantos@ipfn.ist.utl.pt [Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade de Lisboa, 1049-001 Lisboa (Portugal); Carvalho, Paulo F.; Rodrigues, A.P.; Carvalho, Bernardo B.; Sousa, Jorge; Batista, António J.N.; Correia, Miguel; Combo, Álvaro M.; Cruz, Nuno [Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade de Lisboa, 1049-001 Lisboa (Portugal); Correia, Carlos M.B.A. [Centro de Instrumentação, Departamento de Física, Universidade de Coimbra, 3004-516 Coimbra (Portugal); Gonçalves, Bruno [Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade de Lisboa, 1049-001 Lisboa (Portugal)

    2015-10-15

    Highlights: • This architecture targets the health management integration into the NDS. • The developed solution supports the ShM redundancy features, specified by ATCA. • The average RTT was around 59 ms and in 99.9% of the cases was less than 130 ms. • Without losing any update cycle, can monitor a system shelf with approximately 400 sensors. • This solution enables the user to configure the entire system in DB files and st.cmd. - Abstract: The ITER CODAC Core System (CCS) is responsible for plant Instrumentation and Control (I&C) supervising and monitoring. This system uses the Enhanced Physics and Industrial Control System (EPICS) Channel Access (CA) protocol as the interface with the Plant Operation Network (PON). This paper presents a generic EPICS device support developed for the integration of the ATCA Shelf Manager (ShM) into the ITER CCS, providing scalability and easy configuration. The device support uses the available HTTP interface on Shelf Manager in the communication layer. Both HTTP server and sensors/actuators definitions can be configured using the EPICS database file and the Input/Output Controller (IOC) initialization file. A proposal based on this device is also presented, targeting the Nominal Device Support (NDS) for health management. The EPICS device support running in an IOC provides Process Variables (PV) to the PON network with the system information and these PVs can be used by all CA clients, such as EPICS user interface clients, alarm systems and archive systems. Operation with redundant ATCA ShMs and device support scalability tests were performed and the results are presented.

  8. Solar Panel based Milk Pasteurization

    DEFF Research Database (Denmark)

    Nielsen, Kirsten Mølgaard; Pedersen, Tom Søndergaard

    This paper treats the subject of analysis, design and development of the control system for a solar panel based milk pasteurization system to be used in small villages in Tanzania. The analysis deals with the demands for an acceptable pasteurization, the varying energy supply and the low cost, low...... complexity, simple user interface and high reliability demands. Based on these demands a concept for the pasteurization system is established and a control system is developed. A solar panel has been constructed and the energy absorption has been tested in Tanzania. Based on the test, the pasteurization...... system is dimensioned. A functional prototype of the pasteurization facility with a capacity of 200 l milk/hour has been developed and tested. The system is prepared for solar panels as the main energy source and is ready for a test in Tanzania....

  9. Solar Panel based Milk Pasteurization

    DEFF Research Database (Denmark)

    Nielsen, Kirsten Mølgaard; Pedersen, Tom Søndergaard

    2002-01-01

    This paper treats the subject of analysis, design and development of the control system for a solar panel based milk pasteurization system to be used in small villages in Tanzania. The analysis deals with the demands for an acceptable pasteurization, the varying energy supply and the low cost, low...... complexity, simple user interface and high reliability demands. Based on these demands a concept for the pasteurization system is established and a control system is developed. A solar panel has been constructed and the energy absorption has been tested in Tanzania. Based on the test, the pasteurization...... system is dimensioned. A functional prototype of the pasteurization facility with a capacity of 200 l milk/hour has been developed and tested. The system is prepared for solar panels as the main energy source and is ready for a test in Tanzania....

  10. Modelling of pressure increase protection system for the vacuum vessel of W7-X device

    Energy Technology Data Exchange (ETDEWEB)

    Kaliatka, Tadas, E-mail: tadas.kaliatka@lei.lt; Uspuras, Eugenijus; Kaliatka, Algirdas

    2016-11-01

    Highlights: • Two in-vessel LOCAs (partial and guillotine break of 40 mm diameter pipe of cooling system) for Wendelstein 7-X fusion device were analyzed. • The analysis of the processes in the cooling system, vacuum vessel and pressure increase protection system were performed using thermal-hydraulic RELAP5 Mod3.3 code. • The suitability of pressure increase protection system was assessed. - Abstract: In fusion devices, plasma is contained in a vacuum vessel. The vacuum vessel cannot withstand a pressure above atmospheric. Any damage of in-vessel components could lead to water ingress and may lead to pressure increase and possible damage of vacuum vessel. In order to avoid such undesirable consequences, the pressure increase protection system is designed. In this article, the processes occurring in the vacuum vessel and pressure increase protection system of W7-X device during LOCA (small and guillotine pipe break) event are analyzed. The model of W7-X cooling system, vacuum vessel and pressure increase protection system was developed using RELAP5 code. Numerical analysis of partial and guillotine break of 40 mm diameter pipe of cooling system was performed. Calculation results showed that burst disc of the pressure increase protection system does not open when the cross section area of partial break in the cooling system is smaller than 1 mm{sup 2}. During the guillotine break of cooling system, the burst disc opens, but pressure increase protection system is capable to prevent overpressure of the vacuum vessel.

  11. Mitigation of large power spills by an energy storage device in a stand alone energy system

    NARCIS (Netherlands)

    D. Bhaumik (Debarati); D.T. Crommelin (Daan); A.P. Zwart (Bert)

    2018-01-01

    textabstractThe unpredictable nature of wind energy makes its integration to the electric grid highly challenging. However, these challenges can be addressed by incorporating storage devices (batteries) in the system. We perform an overall assessment of a single domestic power system with a wind

  12. Physics-based mathematical models for quantum devices via experimental system identification

    Energy Technology Data Exchange (ETDEWEB)

    Schirmer, S G; Oi, D K L; Devitt, S J [Department of Applied Maths and Theoretical Physics, University of Cambridge, Wilberforce Rd, Cambridge, CB3 0WA (United Kingdom); SUPA, Department of Physics, University of Strathclyde, Glasgow G4 0NG (United Kingdom); National Institute of Informatics, 2-1-2 Hitotsubashi, Chiyoda-ku, Tokyo 101-8430 (Japan)], E-mail: sgs29@cam.ac.uk

    2008-03-15

    We consider the task of intrinsic control system identification for quantum devices. The problem of experimental determination of subspace confinement is considered, and simple general strategies for full Hamiltonian identification and decoherence characterization of a controlled two-level system are presented.

  13. "Joint Workshop on High Confidence Medical Devices, Software, and Systems (HCMDSS) and Medical Device Plug-and-Play (MD PnP) Interoperability"

    National Research Council Canada - National Science Library

    Goldman, Julian M

    2008-01-01

    Partial support was requested from TATRC, with joint funding from NSF, for a joint workshop to bring together the synergistic efforts and communities of the High Confidence Medical Devices, Software, and Systems (HCMDSS...

  14. Design of General-purpose Industrial signal acquisition system in a large scientific device

    Science.gov (United States)

    Ren, Bin; Yang, Lei

    2018-02-01

    In order to measure the industrial signal of a large scientific device experiment, a set of industrial data general-purpose acquisition system has been designed. It can collect 4~20mA current signal and 0~10V voltage signal. Through the practical experiments, it shows that the system is flexible, reliable, convenient and economical, and the system has characters of high definition and strong anti-interference ability. Thus, the system fully meets the design requirements..

  15. Systems and methods for tracking a device in zero-infrastructure and zero-power conditions, and a tracking device therefor

    KAUST Repository

    Shamim, Atif

    2017-03-23

    Disclosed are embodiments for a tracking device having multiple layers of localization and communication capabilities, and particularly having the ability to operate in zero-infrastructure or zero-power conditions. Also disclosed are methods and systems that enhance location determination in zero-infrastructure and zero-power conditions. In one example, a device, system and/or method includes an infrastructure-based localization module, an infrastructure-less localization module and a passive module that can utilize at least two of the modules to determine a location of the tracking device.

  16. Design and Realization of a Condition Management System for the Gateway Electrical Energy Metering Device

    Directory of Open Access Journals (Sweden)

    Chao Tang

    2013-12-01

    Full Text Available With the construction of firm and intelligent power grid in China, it is difficult for the traditional management method of electrical energy metering device to meet the prospecting requirements. Using the computer and internet techniques to realize the information and intelligentization of the electrical energy metering management has become a necessary guarantee of improving power supply ability, marketing control, and customer service. This paper introduced a kind of large and intelligent condition management system of the gateway electrical energy metering device. The key technologies and realize process were analyzed. Moreover, a detailed description of the application modules such as the GIS smart display of metering point, the condition management of metering devices and the visual monitoring of metering point was presented. The trial operation in the selected transformer substations and the power stations of Chongqing Power Electrical Corp. indicated that, the condition management system is very open, safety and efficient. According to the data exchange with the production and scheduling platform, the system improved the efficient operation of the electrical energy metering devices. Meanwhile, combined with the real-time visual monitoring, the condition management system improved the prevention ability of electricity filching, realized the unified automatic large-scale management of electrical energy metering devices.

  17. Note: Fixture for characterizing electrochemical devices in-operando in traditional vacuum systems.

    Science.gov (United States)

    Whaley, Josh A; McDaniel, Anthony H; El Gabaly, Farid; Farrow, Roger L; Grass, Michael E; Hussain, Zahid; Liu, Zhi; Linne, Mark A; Bluhm, Hendrik; McCarty, Kevin F

    2010-08-01

    We describe a fixture that allows electrochemical devices to be studied under electrical bias in the type of vacuum systems commonly used in surface science. Three spring-loaded probes provide independent contacts for device operation and the characterization in vacuum or under in situ conditions with reactive gases. We document the robustness of the electrical contacts over large temperature changes and their reliability for conventional electrochemical measurements such as impedance spectroscopy. The optical access provided to the device enables the analysis by many techniques, as we demonstrate using x-ray photoelectron spectroscopy to measure local electrical potentials on a solid-oxide electrolyte device operating at high temperature in near-ambient pressure.

  18. Laminated Copper Nanocluster Incorporated Antioxidative Paper Device with RGB System-Assisted Signal Improvement

    Directory of Open Access Journals (Sweden)

    Chong-You Chen

    2018-02-01

    Full Text Available Paper-based analytical devices are an emerging class of lightweight and simple-to-use analytical platform. However, challenges such as instrumental requirements and chemical reagents durability, represent a barrier for less-developed countries and markets. Herein, we report an advanced laminated device using red emitting copper nanocluster and RGB digital analysis for signal improvement. Upon RGB system assistance, the device signal-to-background ratio and the calibration sensitivity are highly enhanced under a filter-free setup. In addition, the calibration sensitivity, limit of detection, and coefficient of determination are on par with those determined by instrumental fluorescence analysis. Moreover, the limitation of using oxidation-susceptible fluorescent nanomaterials is overcome by the introduction of protecting tape barriers, antioxidative sheets, and lamination enclosing. The robustness of device is highly advanced, and the durability is prolonged to more than tenfold.

  19. Gore excluder device with the C3 delivery system for management of abdominal aortic aneurysm

    Directory of Open Access Journals (Sweden)

    Morasch MD

    2012-02-01

    Full Text Available Cheong J Lee, Mark L Keldahl, Mark D MoraschDivision of Vascular Surgery, Northwestern University Feinberg School of Medicine, Chicago, IL, USAAbstract: The GORE Excluder stent-graft is one of the currently available devices approved by the US Food and Drug Administration for use in endovascular aortic repair. Recently, a new delivery system modification has been applied to the Excluder device which allows repositioning of the stent-graft to adjust for accurate proximal landing and facilitate gate cannulation. In this review, we examine the Excluder device with the new C3 delivery system and its potential benefit in the management of abdominal aortic aneurysms.Keywords: gore excluder, abdominal aortic aneurysm, repair, C3 delivery system

  20. IoT Enabled Low Cost Wearable Device for Location and Information Tracking System

    Directory of Open Access Journals (Sweden)

    Kamaludin Nur Atika Binti

    2017-01-01

    Full Text Available An internet-of-things (IoT enabled low cost wearable device for location and information tracking system is developed to monitor and ensure the safety of the children while their parents are away either to work or abroad. This system aims to ensure human safety especially the children and efficiently initiate search and rescue in the event of emergencies. The device will notify the parents on the condition of the surroundings of the children, specifically inside the house and notify the parents if the children are outside the target area by using the application developed in the smartphone. The system uses a microcomputer called Beagle-Bone Black (BBB as the processor while GPS and LTE technology for wireless communication. Future improvement mainly focuses on reducing the size and power consumption of the device, improving communication module, and optimizing microcomputer’s specification.