WorldWideScience

Sample records for swing bridges

  1. 33 CFR 118.70 - Lights on swing bridges.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Lights on swing bridges. 118.70 Section 118.70 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY BRIDGES BRIDGE LIGHTING AND OTHER SIGNALS § 118.70 Lights on swing bridges. (a) Swing span lights on through bridges. Each...

  2. Analytical solution of the problem of acceleration of cargo by a bridge crane with constant acceleration at elimination of swings of a cargo rope

    Science.gov (United States)

    Korytov, M. S.; Shcherbakov, V. S.; Titenko, V. V.

    2018-01-01

    Limitation of the swing of the bridge crane cargo rope is a matter of urgency, as it can significantly improve the efficiency and safety of the work performed. In order to completely dampen the pendulum swing after the break-up of a bridge or a bridge-crane freight cart to maximum speed, it is necessary, in the normal repulsion control of the electric motor, to split the process of dispersion into a minimum of three gaps. For a dynamic system of swinging of a bridge crane on a flexible cable hanger in a separate vertical plane, an analytical solution was obtained to determine the temporal dependence of the cargo rope angle relative to the gravitational vertical when the cargo suspension point moves with constant acceleration. The resulting analytical dependence of the cargo rope angle and its first derivative can break the process of dispersing the cargo suspension point into three stages of dispersal and braking with various accelerations and enter maximum speed of movement of the cargo suspension point. In doing so, the condition of eliminating the swings of the cargo rope relative to the gravitational vertical is fulfilled. Provides examples of the maximum speed output constraints-to-time when removing the rope swing.

  3. Dynamics and swing control of double-pendulum bridge cranes with distributed-mass beams

    Science.gov (United States)

    Huang, Jie; Liang, Zan; Zang, Qiang

    2015-03-01

    Motion-induced oscillations of crane payloads seriously degrade their effectiveness and safety. Significant progress has been achieved with reducing payload oscillations on a single-pendulum crane with a point-mass payload attached to the end of the cable. However, large payloads and the actual configuration of the hoisting mechanism may transform the crane to a double-pendulum system with a distributed-mass payload. The manipulation task can be more challenging because of the complicated dynamics. The dynamics of bridge cranes transporting distributed-mass beams are derived. A command-smoothing scheme is presented to suppress the complex payload oscillations. Simulations of a large range of motions are used to analyze the dynamic behavior of the cranes and the robustness of the method. Experimental results obtained from a small-scale double-pendulum bridge crane transporting a distributed-mass beam validate the simulated dynamic behavior and the effectiveness of the method.

  4. Java Swing

    CERN Document Server

    Loy, Marc; Eckstein, Robert; Elliott, James; Wood, Dave

    2003-01-01

    Swing is a fully-featured user interface development kit for Java applications. Building on the foundations of the Abstract Window Toolkit (AWT), Swing enables cross-platform applications to use any of several pluggable look-and-feels. Swing developers can take advantage of its rich, flexible features and modular components, building elegant user interfaces with very little code. This second edition of Java Swing thoroughly covers all the features available in Java 2 SDK 1.3 and 1.4. More than simply a reference, this new edition takes a practical approach. It is a book by developers for

  5. Swinging, Adultery by Consent

    Directory of Open Access Journals (Sweden)

    Olivia Von Der Weid

    2010-09-01

    Full Text Available This research seeks to discuss issues related to the sexual-affective relationships between men and women in our society through the experience of couples who practice swinging. It considers especially the original conceptions of marriage, sexuality, infidelity, and also the rules of a swinger relationship. Does swinging create a new marriage model? Or, instead, does it reinforce pre-existing models? Through an analysis of the discourses of swinging couples about their erotic interactions, the paper examines how they articulate values such as love, sex, and pleasure in their relationships.

  6. ANTI-SWING CRANE

    Science.gov (United States)

    Goertz, R.C.

    1957-09-17

    A device that reduces or eliminntes the swing of an object being transported by a traveling crane is described. The supporting cable of the crane extends through a guide and follower positioned below the crane by an electric motor and follow-up circuit. The swing or horizontal motion of the cable is detected by the follower, and a signal is generated that will cause the motor to move the follower in opposition to the motion of the swing thus having a dampening effect on the pendulum action of the supported body. This improvement is particularly valuable when the supported load may be so radioactive that a person could not manually stop the swing.

  7. SwingStates: adding state machines to the swing toolkit

    OpenAIRE

    Appert , Caroline; Beaudouin-Lafon , Michel

    2006-01-01

    International audience; This article describes SwingStates, a library that adds state machines to the Java Swing user interface toolkit. Unlike traditional approaches, which use callbacks or listeners to define interaction, state machines provide a powerful control structure and localize all of the interaction code in one place. SwingStates takes advantage of Java's inner classes, providing programmers with a natural syntax and making it easier to follow and debug the resulting code. SwingSta...

  8. Swinging in Imaginary Time

    Indian Academy of Sciences (India)

    Home; Journals; Resonance – Journal of Science Education; Volume 15; Issue 2. Swinging in Imaginary Time - More on the Not-So-Simple Pendulum. Cihan Saclioglu. General Article Volume 15 Issue 2 February 2010 pp 104-115. Fulltext. Click here to view fulltext PDF. Permanent link:

  9. El mejor swing

    OpenAIRE

    Baydal Bertomeu, José Mª; Espí Guerola, Luis; Garrido Jaen, Jose David; ALCANTARA ALCOVER, ENRIQUE; Magraner Llavador, Laura; DURA GIL, JUAN-VICENTE; Gómez Herrero, Juan Alfonso; Huertas Leyva, Pedro

    2013-01-01

    [EN] The gesture of the golf swing is a complex movement involving the participation of virtually all segments of the musculoskeletal system, it is also a gesture with a difficult technical execution and it could sometimes be harmful for the golf player. Therefore, IBV makes available to both amateur and professional golfers a set of biomechanical techniques applied to the analysis and improvement of golf technique, biomechanical adaptation and personal...

  10. Playing with a digital swing

    DEFF Research Database (Denmark)

    Skovbjerg, Helle Marie

    2017-01-01

    Based on a field study in a kindergarten among children in Denmark, this paper explores playing activities on a digital swing, the SON-X Octavia (SON-X) and its Applause application. SON-X is an interactive sound unit that can be attached to any swing chain. Here, I explore the relationship betwe...

  11. Swings and roundabouts: management of jealousy in heterosexual swinging couples.

    Science.gov (United States)

    de Visser, Richard; McDonald, Dee

    2007-06-01

    Swinging involves consensual mutual involvement in extra-dyadic sex. Jealousy in swinging couples is an interesting topic for social psychological research, because it is a common and acceptable response to a romantic partner's real or imagined infidelity. This qualitative study examined the management of jealousy among four active heterosexual swinging couples living in southern England. Participants highlighted the importance of discussion and negotiation to develop a shared couple identity and shared rules and boundaries that allowed them to manage jealousy so that they could better enjoy swinging. Rather than seeking to eliminate jealousy, swingers may manage their feelings of jealousy in order to increase sexual excitement and arousal. This study adds to our understanding of jealousy among swingers and the broader issue of jealousy in intimate relationships.

  12. 104 Swinging in Imaginary Time

    Indian Academy of Sciences (India)

    IAS Admin

    104. Swinging in Imaginary Time. More on the Not-So-Simple Pendulum. Cihan Saclioglu. 116. Madhava, Gregory, Leibnitz, and Sums of Two. Squares. Shailesh A Shirali. 124. Electronic Effects in the Cyclocondensation of Benzil. G Nagendrappa. 131. Systems Biology. Karthik Raman and Nagasuma Chandra. 154.

  13. Effects of tempo, swing density, and listener's drumming experience, on swing detection thresholds for drum rhythms.

    Science.gov (United States)

    Frane, Andrew V; Shams, Ladan

    2017-06-01

    Swing, a popular technique in music performance, has been said to enhance the "groove" of the rhythm. Swing works by delaying the onsets of even-numbered subdivisions of each beat (e.g., 16th-note swing delays the onsets of the second and fourth 16th-note subdivisions of each quarter-note beat). The "swing magnitude" (loosely speaking, the amount of delay) is often quite small. And there has been little investigation, using musical stimuli, into what swing magnitudes listeners can detect. To that end, this study presented continually-looped electronic drum rhythms, with 16th-note swing in the hi-hat on every other bar, to drummers and non-drummers. Swing magnitude was adjusted using a staircase procedure, to determine the magnitude where the difference between swinging and not-swinging bars was just-noticeable. Different tempi (60 to 140 quarter-notes per minute) and swing densities (how often notes occurred at even-numbered subdivisions) were used. Results showed that all subjects could detect smaller swing magnitudes when swing density was higher, thus confirming a previous speculation that the perceptual salience of swing increases with swing density. The just-noticeable magnitudes of swing for drummers differed from those of non-drummers, in terms of both overall magnitude and sensitivity to tempo, thus prompting questions for further exploration.

  14. Nasopharyngeal cancer through maxillary swing

    International Nuclear Information System (INIS)

    Pacheco Ojeda, Luis; Chicaiza Acosta, Jorge; Ulloa Miranda, Darwin

    2006-01-01

    Nasopharyngeal cancer is very rare in Ecuador. Radiotherapy associated to concurrent chemotherapy is currently the standard treatment. In case of tumor recurrence, these two treatment modalities are usually not effective. For this reason, several studies about the satisfactory results of salvage surgery in terms of locoregional control of the disease, have appeared recently in the literature. We report our first experience of surgical salvage resection of a recurrent tumor through an anterolateral approach (maxillary swing) with an initial satisfactory result. (The author)

  15. Oxygen cost of kettlebell swings.

    Science.gov (United States)

    Farrar, Ryan E; Mayhew, Jerry L; Koch, Alexander J

    2010-04-01

    In recent years, kettlebells have re-emerged as a popular training modality for the conditioning of athletes. We sought to quantify the aerobic challenge of one popularly recommended kettlebell workout. Ten college-aged men (age = 20.8 +/- 1.1 years, height = 179 +/- 3 cm, body mass = 77.3 +/- 7.7 kg, Vo2max = 52.78 +/- 6.22 ml.kg.min) completed a graded exercise test to exhaustion for the determination of Vo2max. Two to 7 days later, subjects completed a kettlebell exercise routine consisting of as many 2-handed swings as could be completed in 12 minutes using a 16-kg kettlebell. During this exercise bout, subjects' expired gases were collected and analyzed for the determination of Vo2, and heart rate (HR) was continuously measured. Percent HRmax and Vo2max achieved during the kettlebell exercise were compared with each other using a paired t-test. Subjects completed 265 +/- 68 swings during the 12 minutes and achieved an average Vo2 of 34.31 +/- 5.67 ml.kg.min and an average HR of 165 +/- 13 b.min. The average %HRmax (86.8 +/- 6.0%) during kettlebell exercise was significantly higher (p kettlebell swings can impart a metabolic challenge of sufficient intensity to increase Vo2max. Heart rate was substantially higher than Vo2 during kettlebell swings. Kettlebells provide a useful tool with which coaches may improve the cardiorespiratory fitness of their athletes. However, HRs achieved during continuous kettlebell exercise are significantly higher than actual Vo2.

  16. Sour pressure swing adsorption process

    Science.gov (United States)

    Bhadra, Shubhra Jyoti; Wright, Andrew David; Hufton, Jeffrey Raymond; Kloosterman, Jeffrey William; Amy, Fabrice; Weist, Jr., Edward Landis

    2017-11-07

    Methods and apparatuses for separating CO.sub.2 and sulfur-containing compounds from a synthesis gas obtained from gasification of a carbonaceous feedstock. The primary separating steps are performed using a sour pressure swing adsorption (SPSA) system, followed by an acid gas enrichment system and a sulfur removal unit. The SPSA system includes multiple pressure equalization steps and a rinse step using a rinse gas that is supplied from a source other than directly from one of the adsorber beds of the SPSA system.

  17. 49 CFR 236.743 - Dog, swing.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Dog, swing. 236.743 Section 236.743 Transportation... OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Definitions § 236.743 Dog, swing. A locking dog mounted in such a manner that it is free to rotate on a trunnion which is riveted to a locking...

  18. The definitive guide to Java Swing

    CERN Document Server

    Zukowski, John

    2005-01-01

    Updated for the 1.5 edition of the Java 2 Platform, this third edition is a one-stop resource for serious Java developers. It shows the parts of Java Swing API used to create graphical user interfaces (GUI); and Model-View-Controller architecture that lies behind all Swing components; and customizing components for specific environments.

  19. Swinging Over the Water Hole

    Science.gov (United States)

    2011-06-01

    cuerda justo por debajo de su punto de inflexión y cayendo casi en línea recta hacia abajo en el agua desde el reposo. Por otra parte, como la velocidad...final angle1 of f / 2  if 20 2gL  , where g is earth’s R 0  L  FIGURE 1. Trajectory of a child swinging on the end of a rope and...1 cos )y L   , (3) above the water. Basic kinematics then implies that his flight time through the air will be 2 sin sin 2yt g g g

  20. SwingStates: Adding state machines to Java and the Swing toolkit

    OpenAIRE

    Appert , Caroline; Beaudouin-Lafon , Michel

    2008-01-01

    International audience; This article describes SwingStates, a Java toolkit designed to facilitate the development of graphical user interfaces and bring advanced interaction techniques to the Java platform. SwingStates is based on the use of finite-state machines specified directly in Java to describe the behavior of interactive systems. State machines can be used to redefine the behavior of existing Swing widgets or, in combination with a new canvas widget that features a rich graphical mode...

  1. The how and why of arm swing during human walking

    NARCIS (Netherlands)

    Meyns, Pieter; Bruijn, Sjoerd M.; Duysens, Jacques

    Humans walk bipedally, and thus, it is unclear why they swing their arms. In this paper, we will review the mechanisms and functions of arm swinging in human gait. First, we discuss the potential advantages of having swinging arms. Second, we go into the detail on the debate whether arm swing is

  2. The how and why of arm swing during human walking.

    NARCIS (Netherlands)

    Meyns, P.; Bruijn, S.M.; Duysens, J.E.J.

    2013-01-01

    Humans walk bipedally, and thus, it is unclear why they swing their arms. In this paper, we will review the mechanisms and functions of arm swinging in human gait. First, we discuss the potential advantages of having swinging arms. Second, we go into the detail on the debate whether arm swing is

  3. Mechanical demands of kettlebell swing exercise.

    Science.gov (United States)

    Lake, Jason P; Lauder, Mike A

    2012-12-01

    The aims of this study were to establish mechanical demands of kettlebell swing exercise and provide context by comparing them to mechanical demands of back squat and jump squat exercise. Sixteen men performed 2 sets of 10 swings with 16, 24, and 32 kg, 2 back squats with 20, 40, 60, and 80% 1-repetition maximum (1RM), and 2 jump squats with 0, 20, 40, and 60% 1RM. Sagittal plane motion and ground reaction forces (GRFs) were recorded during swing performance, and GRFs were recorded during back and jump squat performances. Net impulse, and peak and mean propulsion phase force and power applied to the center of mass (CM) were obtained from GRF data and kettlebell displacement and velocity from motion data. The results of repeated measures analysis of variance showed that all swing CM measures were maximized during the 32-kg condition but that velocity of the kettlebell was maximized during the 16-kg condition; displacement was consistent across different loads. Peak and mean force tended to be greater during back and jump squat performances, but swing peak and mean power were greater than back squat power and largely comparable with jump squat power. However, the highest net impulse was recorded during swing exercise with 32 kg (276.1 ± 45.3 N·s vs. 60% 1RM back squat: 182.8 ± 43.1 N·s, and 40% jump squat: 231.3 ± 47.1 N·s). These findings indicate a large mechanical demand during swing exercise that could make swing exercise a useful addition to strength and conditioning programs that aim to develop the ability to rapidly apply force.

  4. Operational Investigation of Overhead Crane with Fuzzy Logic Anti-Swing Controller Using 3-D Simulation

    Directory of Open Access Journals (Sweden)

    Y. N. Petrenko

    2011-01-01

    Full Text Available The purpose of a crane control system is to provide load transfer with minimum swinging. The paper presents a developed three-dimensional simulation model of a bridge crane with fuzzy logic controller designed with application of genetic algorithms. Comparative indices of oscillation while load transferring are given in the paper. The indices have been obtained at various parameters of the fuzzy logic controller. 

  5. The Kinetics of Swinging a Baseball Bat.

    Science.gov (United States)

    Crisco, Joseph J; Osvalds, Nikolas J; Rainbow, Michael J

    2018-04-13

    The purpose of this study was to compute the three-dimensional kinetics required to swing three youth baseball bats of varying moments of inertia (MOI). 306 swings by 22 male players (13-18 yrs.) were analyzed. Inverse dynamics with respect to the batter's hands were computed given the known kinematics and physical properties of the bats. We found that peak force increased with larger bat MOI and was strongly correlated with bat tip speed. In contrast, peak moments were weakly correlated with bat MOI and bat tip speed. Throughout the swing, the force applied to the bat was dominated by a component aligned with the long axis of the bat and directed away from the bat knob, while the moment applied to the bat was minimal until just prior to ball impact. These results indicate that players act to mostly "pull" the bat during their swing until just prior to ball impact, at which point they rapidly increase the moment on the bat. This kinetic analysis provides novel insight into the forces and moments used to swing baseball bats.

  6. Correlation of Titleist Performance Institute (TPI) level 1 movement screens and golf swing faults.

    Science.gov (United States)

    Gulgin, Heather R; Schulte, Brian C; Crawley, Amy A

    2014-02-01

    Although some research in the past has examined how physical limitations in strength or flexibility affect a golfer's performance, the performance outcome most measured was driving distance. Currently, there are no data that have examined the relationship between selected strength and flexibility variables and golf swing faults. The purpose of this study was to examine the relationship between Titleist Performance Institute (TPI) level 1 movement screen variables and 14 common golf swing faults. Thirty-six male and female golfers (mean age, 25.4 ± 9.9 years; height, 175.9 ± 16.2 cm; mass, 76.2 ± 14.6 kg; handicap, 14.2 ± 10.4) participated. Twelve physical tests of strength, flexibility, and balance were assessed using the TPI level 1 golf fitness screening tool. Golfers then hit 4 golf shots (with a 5-iron) while being videoed, and those were then analyzed for 14 different golf swing faults (using V1Pro software). Three significant associations between a physical limitation and a particular golf swing fault were found: toe touch and early hip extension (p = 0.015), bridge on right side with both early hip extension (p = 0.050), and loss of posture (p = 0.028). In addition, an odds ratio showed that when a golfer could not overhead deep squat or single leg balance on left side, they were 2-3 times more likely to exhibit a early hip extension, loss of posture, or slide during the golf swing, as compared with those who could perform a correct overhead deep squat. Based on our findings, it is important for the golf fitness professional to particularly address a golfer's core strength, balance, and hamstring flexibility to help avoid common golf swing faults, which affect a golfer's ball striking ability and ultimately their performance.

  7. 78 FR 13747 - Safety Advisory 2013-01; Passing Stop Signals Protecting Movable Bridges

    Science.gov (United States)

    2013-02-28

    ... perform these duties. FOR FURTHER INFORMATION CONTACT: Carlo M. Patrick, Staff Director, Rail and... the train. Unlike most swing bridges that possess end wedges that when driven, prevent rotation of the...

  8. Myocardial Bridge

    Science.gov (United States)

    ... Center > Myocardial Bridge Menu Topics Topics FAQs Myocardial Bridge Article Info En español Your heart is made ... surface of the heart. What is a myocardial bridge? A myocardial bridge is a band of heart ...

  9. Analysis of Swing Movement in Ballroom Dancing

    Directory of Open Access Journals (Sweden)

    Tadashi Shioya

    2018-02-01

    Full Text Available Natural rise and fall movement represents typical characteristics of the swing dances in ballroom dances. The rise and fall movements are analyzed in the mechanical point of view in the presentation. The biomechanics of the rise and fall movements were analyzed in terms of the potential energy and the velocity of the body. Some basic figures of Waltz are taken as examples with application suggestion to the other dances. A sinusoidal function is employed for vertical and horizontal movements in the analysis featuring the natural swing movement of the dancer’s body. The height of center of gravity of dancer and its vertical acceleration are quantitatively exhibited in graphs for each basic movement of the figures of these dances. It is shown that the maximum height in the movement depends on each figure in each dance and that it is limited by the acceleration analysis regardless of dancer’s height or weight.

  10. Tarzan swings: a dangerous new epidemic.

    Science.gov (United States)

    Edwards, D J

    1991-09-01

    Accidental injury in school children was thought to be unpreventable. This series presents the results of 24 consecutive patients with 29 fractures as a result of a fall from a 'Tarzan' rope swing. Twenty-six of the fractures involved the upper limb, 11 patients required hospitalization with operative intervention and 13 required outpatient care only. These types of injury are preventable. The morbidity and pain that these young patients suffer can be avoided.

  11. Swing Weights of Baseball and Softball Bats

    Science.gov (United States)

    Russell, Dan

    2010-01-01

    Baseball and softball bats are sold according to length in inches and weight in ounces. Much to the consternation of players buying new bats, however, not all bats that weigh the same swing the same. The reason for this has to do with moment of inertia of the bat about a pivot point on the handle, or what the sporting goods industry refers to as…

  12. Stepwise Precession of the Resonant Swinging Spring

    Science.gov (United States)

    Holm, Darryl D.; Lynch, Peter

    2002-01-01

    The swinging spring, or elastic pendulum, has a 2:1:1 resonance arising at cubic order in its approximate Lagrangian. The corresponding modulation equations are the well-known three-wave equations that also apply, for example, in laser-matter interaction in a cavity. We use Hamiltonian reduction and pattern evocation techniques to derive a formula that describes the characteristic feature of this system's dynamics, namely, the stepwise precession of its azimuthal angle.

  13. The Java Series. GUI Building with Swing

    CERN Multimedia

    CERN. Geneva

    2000-01-01

    The Swing Java package contains all the components that you expect to see in a modern User Interface, from buttons that contain pictures to trees and grids. It is a big library but it's designed to have the appropriate complexity for the task at hand - if something is simple you don't have to write much code to get it done, but if you want the power to manipulate and deeply customise it you also have it. This tutorial will introduce you to the basic set of components that Swing provides and to the mechanisms behind them. It will provide an overview of what you can do with Swing, even if you are new to GUI programming. However, if you want to follow closely the mechanisms behind what's being explained, it is convenient to have some basic knowledge of the main concepts of Java AWT (class hierarchy and event model) as provided by the previous tutorial of the Java Series. Organiser(s): M.Marquina and R.Ramos /IT-User Support

  14. Swing, o adultério consentido Swinging, adultery by consent

    Directory of Open Access Journals (Sweden)

    Olivia von der Weid

    2010-12-01

    Full Text Available O trabalho tem como objetivo discutir questões referentes às relações afetivo-sexuais entre homens e mulheres na sociedade atual a partir da experiência de casais adeptos da prática do swing. Procura-se compreender as concepções nativas sobre casamento, sexualidade, infidelidade e, também, as regras de uma relação swinger. O swing cria um novo modelo de casamento? Ou reforça os modelos já existentes? Por meio da análise do discurso dos casais adeptos da troca sobre suas interações eróticas, busca-se compreender a forma como se articulam amor, sexo e prazer nesses relacionamentosThis research seeks to discuss issues related to the sexual-affective relationships between men and women in our society through the experience of couples who practice swinging. It considers especially the original conceptions of marriage, sexuality, infidelity, and also the rules of a swinger relationship. Does swinging create a new marriage model? Or, instead, does it reinforce pre-existing models? Through an analysis of the discourses of swinging couples about their erotic interactions, the paper examines how they articulate values such as love, sex, and pleasure in their relationships

  15. Railroad Bridges

    Data.gov (United States)

    Department of Homeland Security — Bridges-Rail in the United States According to The National Bridge Inspection Standards published in the Code of Federal Regulations (23 CFR 650.3), a bridge isA...

  16. CSS-Driven Java Swing Component

    OpenAIRE

    Hvězda, Matěj

    2014-01-01

    Tato práce je zaměřená na vytvoření komponenty Java Swing, která zobrazí obsah HTML dokumentu na základě kaskádových stylů (CSS). Důvod k vytvoření takové komponenty je umožnění vývojářům tvořit uživatelské rozhraní pomocí CSS v Javě bez nutnosti toho, aby znali rozhraní Java Swing.   K syntaktickému rozboru HTML a CSS je použit zobrazovací stroj CSSBox , který umožní získat veškeré potřebné informace ke správnému zobrazení dokumentu. Komponenta je implementována pomocí komponent Swingu...

  17. The Impact of UPFC on Power Swing Blocker

    DEFF Research Database (Denmark)

    Khodaparast, Jalal; Khederzadeh, M.; Silva, Filipe Miguel Faria da

    2016-01-01

    Power Swing Blocker (PSB) is a complementary part in distance relay that detects power swing in the transmission line to prevent unintended operation of distance relay. Unified Power Flow Controller (UPFC) is used in a transmission line to control active and reactive power. The UPFC operation dur...

  18. 77 FR 66703 - Safety Standard for Infant Swings

    Science.gov (United States)

    2012-11-07

    ... at http://www.cpsc.gov/library/foia/foia12/brief/infantswings.pdf . B. The Product 1. Definition ASTM... against allowing infants to sleep in the swing. One of the comments suggests that the following language be added to the warning: ``Do not use the swing for routine sleep.'' (Response 8) We do not believe...

  19. The effects of baseball bat mass properties on swing mechanics, ground reaction forces, and swing timing.

    Science.gov (United States)

    Laughlin, Walter A; Fleisig, Glenn S; Aune, Kyle T; Diffendaffer, Alek Z

    2016-01-01

    Swing trajectory and ground reaction forces (GRF) of 30 collegiate baseball batters hitting a pitched ball were compared between a standard bat, a bat with extra weight about its barrel, and a bat with extra weight in its handle. It was hypothesised that when compared to a standard bat, only a handle-weighted bat would produce equivalent bat kinematics. It was also hypothesised that hitters would not produce equivalent GRFs for each weighted bat, but would maintain equivalent timing when compared to a standard bat. Data were collected utilising a 500 Hz motion capture system and 1,000 Hz force plate system. Data between bats were considered equivalent when the 95% confidence interval of the difference was contained entirely within ±5% of the standard bat mean value. The handle-weighted bat had equivalent kinematics, whereas the barrel-weighted bat did not. Both weighted bats had equivalent peak GRF variables. Neither weighted bat maintained equivalence in the timing of bat kinematics and some peak GRFs. The ability to maintain swing kinematics with a handle-weighted bat may have implications for swing training and warm-up. However, altered timings of kinematics and kinetics require further research to understand the implications on returning to a conventionally weighted bat.

  20. KINEMATIC AND KINETIC VARIABLES DIFFER BETWEEN KETTLEBELL SWING STYLES.

    Science.gov (United States)

    Bullock, Garrett S; Schmitt, Abigail C; Shutt, Jason M; Cook, Gray; Butler, Robert J

    2017-06-01

    Kettlebell (KB) and indian club swings (ICS) are used diversely for developing strength and power. It has been proposed that multiple swing techniques can be used interchangeably to elicit similar adaptations within performance training. Hypothesis/Purpose: It was hypothesized that there will be not be a difference in peak joint angles between types of swings. Furthermore, given the nature of the overhead kettlebell swing (OKS), it was hypothesized that the OKS will be associated with a greater cycle time and a greater vertical impulse compared to shoulder height swing (SKS) and ICS. The purpose of this study was to analyze the kinematics and kinetics of the SKS, OKS, and ICS. Cross-sectional cohort. Fifteen healthy subjects underwent 3D biomechanical analysis for assessment of kinematic and kinetic data. Subjects performed two trials of ten repetitions at full effort for each swing in a randomized order using either a standard set of 0.45 kg indian clubs or sex specific KB loads (Female = 12kg, Male = 20kg). Lower extremity sagittal plane kinematics and kinetics were analyzed for peak values during the down and up portions of the swing patterns. Statistical analyses were carried out utilizing one-way ANOVAs ( p power training. 2.

  1. Hamstring myoelectrical activity during three different kettlebell swing exercises.

    Science.gov (United States)

    Del Monte, Michael J; Opar, David A; Timmins, Ryan G; Ross, James; Keogh, Justin Wl; Lorenzen, Christian

    2017-09-11

    Kettlebell exercises have become an increasingly popular form of resistance training and component of lower body rehabilitative training programs; despite a lack of scientific literature illustrating internal mechanisms and effectiveness of these approaches. Participants (n=14) performed three different styles of kettlebell swings (hip hinge, squat and double knee extension) and were assessed for medial hamstrings (MH) and biceps femoris (BF) myoelectrical activity via surface electromyography (sEMG). Bipolar pre-gelled Ag/AgCl surface electromyography (sEMG) electrodes (10mm diameter, 20mm inter-electrode distance) were placed on the participant's dominant limb after correct skin preparation.There was a main effect for swing type (p = 0.004), where the hip hinge swing elicited a greater overall MH and BF sEMG in comparison to the squat swing (mean difference = 3.92; 95% CI = 1.53 to 6.32; p = 0.002) and the double knee extension swing (mean difference = 5.32; 95% CI = 0.80 to 9.83; p = 0.020). Across all swing types, normalised percentage of MH sEMG was significantly higher compared to the BF (mean difference = 9.93; 95% CI = 1.67 to 18.19; p = 0.022). The hip hinge kettlebell swing produced the greatest amount of hamstring sEMG for the three styles of kettlebell swings assessed. These findings have implications for the application of kettlebell swing exercises in strength and conditioning, injury prevention and rehabilitation programs.

  2. Gas separation by pressure swing adsorption

    International Nuclear Information System (INIS)

    Martin, J.R.; Gottzman, C.F.; Notaro, F.; Stewart, H.A.

    1986-01-01

    Over the past twenty years separation processes based upon pressure swing adsorption have replaced cryogenic processes in a number of selected applications such as air separation for production of moderate quantities of nitrogen and oxygen and recovery of hydrogen from refinery and chemical plant gases. Key events contributing to the emergence of PSA as an important process option have been the development of synthetic zeolite molecular sieves by Union Carbide Corporation in the USA and of carbon molecular sieves by Bergbau-Forschung in Germany. Today PSA processes enjoy significant commercial use producing oxygen from 0.1 Nm 3 /h for medical application to 1500 Nm 3 /h for steel mill use, for making nitrogen up to 1000 Nm 3 /h for inerting and in purifying hydrogen streams of up to 100,000 Nm 3 /h for refinery use. In this paper some of the principles of adsorptive separations are reviewed. The history of the technology is traced briefly with emphasis on key material, process and application events. The major commercial processes in the application of adsorption to bulk separation of air and hydrogen purification are reviewed in more detail with comparisons made to cryogenic alternatives in terms of specific characteristics, advantages and disadvantages where appropriate. Information on performance, reliability and comparative economics are discussed where available

  3. A swing driven by liquid crystals

    Science.gov (United States)

    Cheng, Cheng

    Angular momentum in liquid crystals exists as flow, director reorientation, etc. However, it is hard to observe and measure angular momentum in liquid crystals by a direct mechanical approach. Torsion pendulum is a general tool to measure angular momentum by torque balance. Our torsion pendulum can harvest the angular momentum in liquid crystals to make it observable. The oscillation of the pendulum keeps increasing by constructively adding a small angular momentum of liquid crystals each period at the resonant frequency of the pendulum. Its similar to a swing driven by a force at its resonant frequency. For the torsion pendulum, a cage made of two aluminum discs, in which a liquid crystal cell is placed, is suspended between two thin tungsten wires. A gold mirror, which is a part of the optical lever system, is attached on one tungsten wire. As first demonstration, we fabricate a circular hybrid liquid crystal cell, which can induce concentric backflows to generate angular momentum. The alignment on the planar substrate is concentric and tangential. Due to the coupling between director rotation and flow, the induced backflow goes around the cell when we add electrical pulses between top and bottom substrates. The oscillation is observed by a position sensitive detector and analyzed on the basis of Eriksen-Leslie theory. With vacuum condition and synchronous driving system, the oscillation signal is improved. We demonstrate that this torsion pendulum can sensitively detect the angular momentum in liquid crystals.

  4. Kinetic bridges.

    Science.gov (United States)

    1980-01-01

    This report on kinetic bridges is essentially a state-of-the-art study on two types of bridges whose location or physical characteristics are designed to be time dependent. The first type, called a "relocatable bridge", is essentially for use as a te...

  5. Active-learning physics experiments using the Tarzan Swing

    Science.gov (United States)

    Trout, K. P.; Gaston, Charles A.

    2001-03-01

    By reversing the conventional laboratory sequences, the Tarzan Swing engages and excites students, improving learning and retention. Problems are solved theoretically, then solutions are verified physically. Failure engenders reanalysis; success brings cheers. Students work overtime eagerly to achieve that success.

  6. Separation of hydrogen isotopes via single column pressure swing adsorption

    International Nuclear Information System (INIS)

    Wong, Y.W.; Hill, F.B.

    1981-01-01

    Separation of hydrogen isotopes based on kinetic isotope effects was studied. The mixture separated was hydrogen containing a trace of tritium as HT and the hydride was vanadium monohydride. The separation was achieved using the single-column pressure swing process. Stage separation factors are larger and product cuts smaller than for a two-column pressure swing process operated in the same monohydride phase

  7. CFD Analysis of Swing of Cricket Ball and Trajectory Prediction

    Science.gov (United States)

    G, Jithin; Tom, Josin; Ruishikesh, Kamat; Jose, Jyothish; Kumar, Sanjay

    2013-11-01

    This work aims to understand the aerodynamics associated with the flight and swing of a cricket ball and predict its flight trajectory over the course of the game: at start (smooth ball) and as the game progresses (rough ball). Asymmetric airflow over the ball due to seam orientation and surface roughness can cause flight deviation (swing). The values of Drag, Lift and Side forces which are crucial for determining the trajectory of the ball were found with the help of FLUENT using the standard K- ɛ model. Analysis was done to study how the ball velocity, spin imparted to be ball and the tilt of the seam affects the movement of the ball through air. The governing force balance equations in 3 dimensions in combination a MATLAB code which used Heun's method was used for obtaining the trajectory of the ball. The conditions for the conventional swing and reverse swing to occur were deduced from the analysis and found to be in alignment with the real life situation. Critical seam angle for maximum swing and transition speed for normal to reverse swing were found out. The obtained trajectories were compared to real life hawk eye trajectories for validation. The analysis results were in good agreement with the real life situation.

  8. Effects of moment of inertia on restricted motion swing speed.

    Science.gov (United States)

    Schorah, David; Choppin, Simon; James, David

    2015-06-01

    In many sports, the maximum swing speed of a racket, club, or bat is a key performance parameter. Previous research in multiple sports supports the hypothesis of an inverse association between the swing speed and moment of inertia of an implement. The aim of this study was to rigorously test and quantify this relationship using a restricted swinging motion. Eight visually identical rods with a common mass but variable moment of inertia were manufactured. Motion capture technology was used to record eight participants' maximal effort swings with the rods. Strict exclusion criteria were applied to data that did not adhere to the prescribed movement pattern. The study found that for all participants, swing speed decreased with respect to moment of inertia according to a power relationship. However, in contrast to previous studies, the rate of decrease varied from participant to participant. With further analysis it was found that participants performed more consistently at the higher end of the moment of inertia range tested. The results support the inverse association between swing speed and moment of inertia but only for higher moment of inertia implements.

  9. An prediction and explanation of 'climatic swing

    Science.gov (United States)

    Barkin, Yury

    2010-05-01

    Introduction. In works of the author [1, 2] the mechanism has been offered and the scenario of formation of congelations and warming of the Earth and their inversion and asymmetric displays in opposite hemispheres has been described. These planetary thermal processes are connected with gravitational forced oscillations of the core-mantle system of the Earth, controlling and directing submission of heat in the top layers of the mantle and on a surface of the Earth. It is shown, that action of this mechanism should observed in various time scales. In particular significant changes of a climate should occur to the thousand-year periods, with the periods in tens and hundred thousand years. Thus excitation of system the core-mantle is caused by planetary secular orbital perturbations and by perturbations of the Earth rotation which as is known are characterized by significant amplitudes. But also in a short time scale the climate variations with the interannual and decade periods also should be observed, how dynamic consequences of the swing of the core-mantle system of the Earth with the same periods [3]. The fundamental phenomenon of secular polar drift of the core relatively to the viscous-elastic and changeable mantle [4] in last years has obtained convincing confirmations various geosciences. Reliable an attribute of influence of oscillations of the core on a variation of natural processes is their property of inversion when, for example, activity of process accrues in northern hemisphere and decreases in a southern hemisphere. Such contrast secular changes in northern and southern (N/S) hemispheres have been predicted on the base of geodynamic model [1] and revealed according to observations: from gravimetry measurements of a gravity [5]; in determination of a secular trend of a sea level, as global, and in northern and southern hemispheres [6, 7]; in redistribution of air masses [6, 8]; in geodetic measurements of changes of average radiuses of northern and

  10. Split-arm swinging: the effect of arm swinging manipulation on interlimb coordination during walking.

    Science.gov (United States)

    Bondi, Moshe; Zeilig, Gabi; Bloch, Ayala; Fasano, Alfonso; Plotnik, Meir

    2017-08-01

    Human locomotion is defined by bilateral coordination of gait (BCG) and shared features with the fore-hindlimb coordination of quadrupeds. The objective of the present study is to explore the influence of arm swinging (AS) on BCG. Sixteen young, healthy individuals (eight women; eight right motor-dominant, eight left-motor dominant) participated. Participants performed 10 walking trials (2 min). In each of the trials AS was unilaterally manipulated (e.g., arm restriction, weight on the wrist), bilaterally manipulated, or not manipulated. The order of trials was random. Walking trials were performed on a treadmill. Gait kinematics were recorded by a motion capture system. Using feedback-controlled belt speed allowed the participants to walk at a self-determined gait speed. Effects of the manipulations were assessed by AS amplitudes and the phase coordination index (PCI), which quantifies the left-right anti-phased stepping pattern. Most of the AS manipulations caused an increase in PCI values (i.e., reduced lower limb coordination). Unilateral AS manipulation had a reciprocal effect on the AS amplitude of the other arm such that, for example, over-swinging of the right arm led to a decrease in the AS amplitude of the left arm. Side of motor dominance was not found to have a significant impact on PCI and AS amplitude. The present findings suggest that lower limb BCG is markedly influenced by the rhythmic AS during walking. It may thus be important for gait rehabilitation programs targeting BCG to take AS into account. NEW & NOTEWORTHY Control mechanisms for four-limb coordination in human locomotion are not fully known. To study the influence of arm swinging (AS) on bilateral coordination of the lower limbs during walking, we introduced a split-AS paradigm in young, healthy adults. AS manipulations caused deterioration in the anti-phased stepping pattern and impacted the AS amplitudes for the contralateral arm, suggesting that lower limb coordination is markedly

  11. Myocardial Bridging

    Directory of Open Access Journals (Sweden)

    Shi-Min Yuan

    2016-02-01

    Full Text Available Abstract Myocardial bridging is rare. Myocardial bridges are most commonly localized in the middle segment of the left anterior descending coronary artery. The anatomic features of the bridges vary significantly. Alterations of the endothelial morphology and the vasoactive agents impact on the progression of atherosclerosis of myocardial bridging. Patients may present with chest pain, myocardial infarction, arrhythmia and even sudden death. Patients who respond poorly to the medical treatment with β-blockers warrant a surgical intervention. Myotomy is a preferred surgical procedure for the symptomatic patients. Coronary stent deployment has been in limited use due to the unsatisfactory long-term results.

  12. WORK AND POWER ANALYSIS OF THE GOLF SWING

    Directory of Open Access Journals (Sweden)

    Steven M. Nesbit

    2005-12-01

    Full Text Available A work and power (energy analysis of the golf swing is presented as a method for evaluating the mechanics of the golf swing. Two computer models were used to estimate the energy production, transfers, and conversions within the body and the golf club by employing standard methods of mechanics to calculate work of forces and torques, kinetic energies, strain energies, and power during the golf swing. A detailed model of the golf club determined the energy transfers and conversions within the club during the downswing. A full-body computer model of the golfer determined the internal work produced at the body joints during the downswing. Four diverse amateur subjects were analyzed and compared using these two models. The energy approach yielded new information on swing mechanics, determined the force and torque components that accelerated the club, illustrated which segments of the body produced work, determined the timing of internal work generation, measured swing efficiencies, calculated shaft energy storage and release, and proved that forces and range of motion were equally important in developing club head velocity. A more comprehensive description of the downswing emerged from information derived from an energy based analysis

  13. The Effect of Kettlebell Swing Load and Cadence on Physiological, Perceptual and Mechanical Variables

    OpenAIRE

    Michael J. Duncan; Rosanna Gibbard; Leanne M. Raymond; Peter Mundy

    2015-01-01

    This study compared the physiological, perceptual and mechanical responses to kettlebell swings at different loads and swing speeds. Following familiarization 16 strength trained participants (10 males, six females, mean age ± SD = 23 ± 2.9) performed four trials: 2 min kettlebell swings with an 8 kg kettlebell at a fast cadence; 2 min kettlebell swings with an 8 kg kettlebell at a slow cadence; 4 min kettlebell swings with a 4 kg kettlebell at a fast cadence; 4 min kettlebell swings with a 4...

  14. JavaFX2 a Swing

    OpenAIRE

    Čapek, Ondřej

    2011-01-01

    The bachelor thesis deals mainly with the JavaFX2 library and its innovations. An aim is to acquaint readers with wider possibilities and help them with a transition from Swing to JavaFX2. In the thesis there are gone into benefits JavaFX2 which is accompanied by a source code examples for an illustration. A part of the thesis is also an application which shows differences between Swing and JavaFX2 both a graphical view as well as a viewing of the source code. Most of the information containe...

  15. A Standalone Vision Impairments Simulator for Java Swing Applications

    Science.gov (United States)

    Oikonomou, Theofanis; Votis, Konstantinos; Korn, Peter; Tzovaras, Dimitrios; Likothanasis, Spriridon

    A lot of work has been done lately in an attempt to assess accessibility. For the case of web rich-client applications several tools exist that simulate how a vision impaired or colour-blind person would perceive this content. In this work we propose a simulation tool for non-web JavaTM Swing applications. Developers and designers face a real challenge when creating software that has to cope with a lot of interaction situations, as well as specific directives for ensuring an accessible interaction. The proposed standalone tool will assist them to explore user-centered design and important accessibility issues for their JavaTM Swing implementations.

  16. Software-based governor control helps manage power swings

    Energy Technology Data Exchange (ETDEWEB)

    Bauman, T.A. [Woodward Governor Co., Loveland, CO (United States); Stead, D.P. [Homer Electric Association, AK (United States)

    1995-12-01

    Severe power swings occurring when water flow increases to impulse turbines at the 120-MW Bradley Lake Project in Alaska are managed by an innovative governor control scheme. To control severe power swings occurring when water flow increased to the impulse turbines at the Bradley Lake Project near Homer, Alaska, the plant`s governor was reprogrammed. This reprogramming was made possible owing to the use of state-of-the-art digital electronics. The new control scheme, which focuses on using the total flow of water ot the turbine rather than manipulating individual needle positions, is an appropriate solution for other high-head hydroelectric plants with impulse turbines encountering similar problems.

  17. Effect of arm swing strategy on local dynamic stability of human gait.

    Science.gov (United States)

    Punt, Michiel; Bruijn, Sjoerd M; Wittink, Harriet; van Dieën, Jaap H

    2015-02-01

    Falling causes long term disability and can even lead to death. Most falls occur during gait. Therefore improving gait stability might be beneficial for people at risk of falling. Recently arm swing has been shown to influence gait stability. However at present it remains unknown which mode of arm swing creates the most stable gait. To examine how different modes of arm swing affect gait stability. Ten healthy young male subjects volunteered for this study. All subjects walked with four different arm swing instructions at seven different gait speeds. The Xsens motion capture suit was used to capture gait kinematics. Basic gait parameters, variability and stability measures were calculated. We found an increased stability in the medio-lateral direction with excessive arm swing in comparison to normal arm swing at all gait speeds. Moreover, excessive arm swing increased stability in the anterior-posterior and vertical direction at low gait speeds. Ipsilateral and inphase arm swing did not differ compared to a normal arm swing. Excessive arm swing is a promising gait manipulation to improve local dynamic stability. For excessive arm swing in the ML direction there appears to be converging evidence. The effect of excessive arm swing on more clinically relevant groups like the more fall prone elderly or stroke survivors is worth further investigating. Excessive arm swing significantly increases local dynamic stability of human gait. Copyright © 2014 Elsevier B.V. All rights reserved.

  18. Bridge Management Systems

    DEFF Research Database (Denmark)

    Thoft-Christensen, Palle

    In this paper bridge management systems are discussed with special emphasis on management systems for reinforced concrete bridges. Management systems for prestressed concrete bridges, steel bridges, or composite bridges can be developed in a similar way.......In this paper bridge management systems are discussed with special emphasis on management systems for reinforced concrete bridges. Management systems for prestressed concrete bridges, steel bridges, or composite bridges can be developed in a similar way....

  19. 77 FR 7011 - Safety Standard for Infant Swings

    Science.gov (United States)

    2012-02-10

    ...) lack the neck muscle tone and strength to keep their head up. In 4 of the 5 slump-over deaths, the... asphyxiation occurs when the position of the child's body (such as compression of their neck from their head... a swing motion that is not horizontal, we are proposing that the text of ASTM F 2088-11b section 7.3...

  20. Input Shaping for Helicopter Slung Load Swing Reduction

    DEFF Research Database (Denmark)

    Bisgaard, Morten; la Cour-Harbo, Anders; Bendtsen, Jan Dimon

    2008-01-01

    This chapter presents a feedforward swing reducing control system for augmenting already existing helicopter controllers and enables slung load flight with autonomous helicopters general cargo transport. The feedforward controller is designed to avoid excitation of the lightly damped modes of the...

  1. Optimal operation of rapid pressure swing adsorption with slop recycling

    NARCIS (Netherlands)

    Betlem, Bernardus H.L.; Gotink, R.W.M.; Bosch, H.

    1998-01-01

    Rapid pressure swing adsorption (RPSA) is a cyclic process operating, basically, in three phases: a pressurization, a delay, and a depressurization phase. A new, modified operation is suggested by the addition of either a raffinate recycle phase or an extract recycle phase, during which raffinate

  2. Expert Baseball Batters Have Greater Sensitivity in Making Swing Decisions

    Science.gov (United States)

    Gray, Rob

    2010-01-01

    This study used signal detection theory to conceptualize the problem a baseball batter faces when deciding whether or not to swing at a pitch. It examined the launch angle (LA) criteria used by expert (college players) and less experienced (recreational league players) batters using a baseball batting simulation. This study showed that, although…

  3. Pressure Swing Adsorption in the Unit Operations Laboratory

    Science.gov (United States)

    Ganley, Jason

    2018-01-01

    This paper describes a student laboratory in the Unit Operations Laboratory at the Colorado School of Mines: air separation by pressure swing adsorption. The flexibility of the system enables students to study the production of enriched nitrogen or oxygen streams. Automatic data acquisition permits the study of cycle steps and performance.…

  4. Swing States, The Winner-Take-All Electoral College, and Fiscal Federalism

    OpenAIRE

    Duquette, Christopher; Mixon, Franklin; Cebula, Richard

    2013-01-01

    There is a debate regarding the impact of swing or independent voters in American politics. While some argue that swing voters either do not swing or have a marginal impact on campaigns, the decline in voter partisan identification and the rise of independents means that they have a potential impact on elections, making them a desirable commodity to candidates. Additionally, presidential elections represent a unique case for swing voters. A robust literature notes that during the presidenti...

  5. LUMBAR CORSETS CAN DECREASE LUMBAR MOTION IN GOLF SWING

    Directory of Open Access Journals (Sweden)

    Koji Hashimoto

    2013-03-01

    Full Text Available Swinging a golf club includes the rotation and extension of the lumbar spine. Golf-related low back pain has been associated with degeneration of the lumbar facet and intervertebral discs, and with spondylolysis. Reflective markers were placed directly onto the skin of 11young male amateur golfers without a previous history of back pain. Using a VICON system (Oxford Metrics, U.K., full golf swings were monitored without a corset (WOC, with a soft corset (SC, and with a hard corset (HC, with each subject taking 3 swings. Changes in the angle between the pelvis and the thorax (maximum range of motion and angular velocity in 3 dimensions (lumbar rotation, flexion-extension, and lateral tilt were analyzed, as was rotation of the hip joint. Peak changes in lumbar extension and rotation occurred just after impact with the ball. The extension angle of the lumbar spine at finish was significantly lower under SC (38° or HC (28° than under WOC (44° conditions (p < 0.05. The maximum angular velocity after impact was significantly smaller under HC (94°/sec than under SC (177°/sec and WOC (191° /sec conditions, as were the lumbar rotation angles at top and finish. In contrast, right hip rotation angles at top showed a compensatory increase under HC conditions. Wearing a lumbar corset while swinging a golf club can effectively decrease lumbar extension and rotation angles from impact until the end of the swing. These effects were significantly enhanced while wearing an HC

  6. National Bridge Inventory (NBI) Bridges

    Data.gov (United States)

    Department of Homeland Security — The NBI is a collection of information (database) describing the more than 600,000 of the Nation's bridges located on public roads, including Interstate Highways,...

  7. Effect of active arm swing to local dynamic stability during walking.

    Science.gov (United States)

    Wu, Yu; Li, Yue; Liu, An-Min; Xiao, Fei; Wang, Yin-Zhi; Hu, Fei; Chen, Jin-Ling; Dai, Ke-Rong; Gu, Dong-Yun

    2016-02-01

    Arm swing is an essential component in regulating dynamic stability of the whole body during walking, while the contribution of active arm swing to local dynamic stability of different motion segments remains unclear. This study investigated the effects of arm swing under natural arm swing condition and active arm swing condition on local dynamic stability and gait variability of the trunk segments (C7 and T10 joint) and lower extremity joints (hip, knee and ankle joint). The local divergence exponents (λs) and mean standard deviation over strides (MeanSD) of 24 young healthy adults were calculated while they were walking on treadmill with two arm swing conditions at their preferred walking speed (PWS). We found that in medial-lateral direction, both λs and MeanSD values of the trunk segments (C7 and T10 joint) in active arm swing condition were significantly lower than those in natural arm swing condition (parm swing conditions (p>0.05, respectively). In anterior-posterior and vertical direction, neither λs nor MeanSD values of all body segments showed significant difference between two arm swing conditions (p>0.05, respectively). These findings indicate that active arm swing may help to improve the local dynamic stability of the trunk segments in medial-lateral direction. Copyright © 2015 Elsevier B.V. All rights reserved.

  8. Optimization analysis of swing check valve closing induced water hammer

    International Nuclear Information System (INIS)

    Han Wenwei; Han Weishi; Guo Qing; Wang Xin; Liu Chunyu

    2014-01-01

    A mathematical-physics model of double pump parallel feed system was constructed. The water hammer was precisely calculated, which was formed in the closing process of swing check valve. And a systematic analysis was carried out to determine the influence of the torques from both valve plate and damping torsion spring on the valve closing induced water hammer. The results show that the swing check valve would distinctly produce the water hammer during the closing procedure in the double pump parallel feed water system. The torques of the valve plate can partly reduce the water hammer effect, and implying appropriate materials of valve plate and appropriate spring can effectively relieve the harm of water hammer. (authors)

  9. Swing Damping for Helicopter Slung Load Systems using Delayed Feedback

    DEFF Research Database (Denmark)

    Bisgaard, Morten; la Cour-Harbo, Anders; Bendtsen, Jan Dimon

    2009-01-01

    of swing. The design of the delayed feedback controller is presented as an optimization problem which gives the possibility of an automated design process. Simulations and flight test verifications of the control system on two different autonomous helicopters are presented and it is shown how a significant......This paper presents the design and verification of a swing reducing controller for helicopter slung load systems using intentional delayed feedback. It is intended for augmenting a trajectory tracking helicopter controller and thereby improving the slung load handing capabilities for autonomous...... helicopters. The delayed feedback controller is added to actively reduce oscillations of the slung load by improving the damping of the slung load pendulum modes. Furthermore, it is intended for integration with a feedforward control scheme based on input shaping for concurrent avoidance and dampening...

  10. Balance Devices Train Golfers for a Consistent Swing

    Science.gov (United States)

    2015-01-01

    As part of the effort to understand the effects of spaceflight on astronauts, NASA funded research that resulted in a commercial product to treat balance disorders. West Palm Beach, Florida-based Sports Therapy Inc. worked with the inventor to modify the technology, creating the Dynamic Balance System (DBS) for sports applications. DBS is now used by Professional Golfers' Association-owned facilities and golf academies to help players achieve an effective, balanced swing.

  11. Simulated Lunar Testing of Metabolic Heat Regenerated Temperature Swing Adsorption

    Science.gov (United States)

    Padilla, Sebastian A.; Bower, Chad E.; Iacomini, Christie S.; Paul, Heather L.

    2012-01-01

    Metabolic heat regenerated Temperature Swing Adsorption (MTSA) technology is being developed for thermal and carbon dioxide (CO2) control for a Portable Life Support System (PLSS), as well as water recycling. An Engineering Development Unit (EDU) of the MTSA Subassembly (MTSAS) was designed and assembled for optimized Martian operations, but also meets system requirements for lunar operations. For lunar operations the MTSA sorption cycle is driven via a vacuum swing between suit ventilation loop pressure and lunar vacuum. The focus of this effort was testing in a simulated lunar environment. This environment was simulated in Paragon's EHF vacuum chamber. The objective of the testing was to evaluate the full cycle performance of the MTSA Subassembly EDU, and to assess CO2 loading and pressure drop of the wash coated aluminum reticulated foam sorbent bed. Lunar environment testing proved out the feasibility of pure vacuum swing operation, making MTSA a technology that can be tested and used on the Moon prior to going to Mars. Testing demonstrated better than expected CO2 Nomenclature loading on the sorbent and nearly replicates the equilibrium data from the sorbent manufacturer. This exceeded any of the previous sorbent loading tests performed by Paragon. Subsequently, the increased performance of the sorbent bed design indicates future designs will require less mass and volume than the current EDU rendering MTSA as very competitive for Martian PLSS applications.

  12. UPGRADING METHANE USING ULTRA-FAST THERMAL SWING ADSORPTION

    Energy Technology Data Exchange (ETDEWEB)

    Anna Lee Tonkovich

    2004-01-01

    The purpose of this project is to design and demonstrate an approach to upgrade low-BTU methane streams from coal mines to pipeline-quality natural gas. The objective of Phase I of the project was to assess the feasibility of upgrading low-Btu methane streams using ultra-fast thermal swing adsorption (TSA) using Velocys' modular microchannel process technology. The project is on schedule and under budget. For Task 1.1, the open literature, patent information, and vendor contacts were surveyed to identify adsorbent candidates for experimental validation and subsequent demonstration in an MPT-based ultra-fast TSA separation for methane upgrading. The leading candidates for preferential adsorption of methane over nitrogen are highly microporous carbons. A Molecular Gate{trademark} zeolite from Engelhard Corporation has emerged as a candidate. For Task 1.2, experimental evaluation of adsorbents was initiated, and data were collected on carbon (MGN-101) from PICA, Inc. This carbon demonstrated a preferential capacity for methane over nitrogen, as well as a reasonable thermal swing differential capacity for a 90% methane and 10% nitrogen mixture. A similar methane swing capacity at 2 psig was measured. The mixture composition is relevant because gob gas contains nearly 85% methane and must be purified to 97% methane for pipeline quality.

  13. Building Bridges

    DEFF Research Database (Denmark)

    The report Building Bridges adresses the questions why, how and for whom academic audience research has public value, from the different points of view of the four working groups in the COST Action IS0906 Transforming Audiences, Transforming Societies – “New Media Genres, Media Literacy and Trust...

  14. Bridging Anticoagulation

    Science.gov (United States)

    ... Procedure? The BRIDGE Study Investigators Download PDF https://doi.org/10.1161/CIRCULATIONAHA.111.084517 Circulation. 2012; 125: ... e496-e498 , originally published March 26, 2012 https://doi.org/10.1161/CIRCULATIONAHA.111.084517 Citation Manager Formats ...

  15. Crossing Bridges

    Indian Academy of Sciences (India)

    Perhaps we are not smart enough. How would we go about establishing that the problem has no solution? One possibility is to enumerate all possible ... Even if we do this for the bridges of Konigsberg, we would learn nothing about other similar situations. Consider for example the fictitious city of Lutetia at the confluence of.

  16. Mathematical bridges

    CERN Document Server

    Andreescu, Titu; Tetiva, Marian

    2017-01-01

    Building bridges between classical results and contemporary nonstandard problems, Mathematical Bridges embraces important topics in analysis and algebra from a problem-solving perspective. Blending old and new techniques, tactics and strategies used in solving challenging mathematical problems, readers will discover numerous genuine mathematical gems throughout that will heighten their appreciation of the inherent beauty of mathematics. Most of the problems are original to the authors and are intertwined in a well-motivated exposition driven by representative examples. The book is structured to assist the reader in formulating and proving conjectures, as well as devising solutions to important mathematical problems by making connections between various concepts and ideas from different areas of mathematics. Instructors and educators teaching problem-solving courses or organizing mathematics clubs, as well as motivated mathematics students from high school juniors to college seniors, will find Mathematical Bri...

  17. The acute hormonal response to the kettlebell swing exercise.

    Science.gov (United States)

    Budnar, Ronald G; Duplanty, Anthony A; Hill, David W; McFarlin, Brian K; Vingren, Jakob L

    2014-10-01

    The purpose of this investigation was to examine the acute hormonal response to the kettlebell swing exercise. Ten recreationally resistance trained men (age, 24 ± 4 years; height, 175 ± 6 cm; body mass, 78.7 ± 9.9 kg) performed 12 rounds of 30 seconds of 16 kg kettlebell swings alternated with 30 seconds of rest. Blood samples were collected before (PRE), immediately after (IP), and 15 (P15) and 30 minutes after exercise (P30) and analyzed for testosterone (T), immunoreactive growth hormone, cortisol (C), and lactate concentrations. Heart rate and rating of perceived exertion were measured at the end of each round. Testosterone was significantly higher (p ≤ 0.05) at IP than at PRE, P15, or P30 (PRE: 28 ± 3; IP: 32 ± 4; P15: 29 ± 3; P30: 27 ± 3 nmol·L). Growth hormone was higher at IP, P15, and P30 than at PRE (PRE: 0.1 ± 0.1; IP: 1.8 ± 1.2; P15: 2.1 ± 1.1; P30: 1.6 ± 1.3 μg·L). Cortisol was higher at IP and P15 than at PRE and P30 (PRE: 617 ± 266; IP: 894 ± 354; P15: 875 ± 243; P30: 645 ± 285 nmol·L). Lactate was higher at IP, P15, and P30 than at PRE (PRE: 1.1 ± 0.5; IP: 7.0 ± 3.0; P15: 4.0 ± 2.7; P30: 2.5 ± 1.8 mmol·L). Heart rate increased progressively from 57 ± 12 at PRE to 170 ± 10 at IP. The exercise protocol produced an acute increase in hormones involved in muscle adaptations. Thus, the kettlebell swing exercise might provide a good supplement to resistance training programs.

  18. Analysis of Human Swing Movement and Transferring into Robot

    Science.gov (United States)

    Shimodaira, Jun; Amaoka, Yuki; Hamatani, Shinsuke; Takeuchi, Masahiro; Hirai, Hiroaki; Miyazaki, Fumio

    Based on Generalized Motor Program, we analyzed the skill of human's table-tennis movement We hypothesized that it can be divided into arm swing and translational movements by upper and lower body movements, respectively. We expressed 3D position of the racket by only one parameter resulted from the analysis using Principal Component Analysis. Body trunk position measurement attested the lower body plays the role of keeping fixed relative-position between the ball and the body trunk at any hitting time. By applying human skills in upper and lower body movements, we could make the robot properly play table-tennis with a human.

  19. Early Prediction of Transient Voltage Sags caused by Rotor Swings

    DEFF Research Database (Denmark)

    Weckesser, Johannes Tilman Gabriel; Jóhannsson, Hjörtur; Van Cutsem, Thierry

    2014-01-01

    The paper investigates various methods to predict voltage sags at load buses caused by large generator rotor swings and following a transient disturbance. Three different prediction methods are proposed, which all use real-time measurements from PMUs. One of the methods uses a slightly extended...... version of the E-SIME method. The other two methods use Measurements and process them by recursive least square estimation. It is shown that the prediction method employing E-SIME allows the earliest detection of a critical voltage sag with satisfactory accuracy....

  20. Sound Synthesis of Objects Swinging through Air Using Physical Models

    Directory of Open Access Journals (Sweden)

    Rod Selfridge

    2017-11-01

    Full Text Available A real-time physically-derived sound synthesis model is presented that replicates the sounds generated as an object swings through the air. Equations obtained from fluid dynamics are used to determine the sounds generated while exposing practical parameters for a user or game engine to vary. Listening tests reveal that for the majority of objects modelled, participants rated the sounds from our model as plausible as actual recordings. The sword sound effect performed worse than others, and it is speculated that one cause may be linked to the difference between expectations of a sound and the actual sound for a given object.

  1. Extension - Upgrading Methane Using Ultra-Fast Thermal Swing Adsorption

    Energy Technology Data Exchange (ETDEWEB)

    Anna Lee Tonkovich

    2008-08-11

    The need for cost effective technologies for upgrading coal mine methane to pipeline quality natural gas is becoming ever greater. The current work presents and investigates a new approach to reduce the impact of the most costly step in the conventional technology, nitrogen rejection. The proposed approach is based on the Velocys microchannel platform, which is being developed to commercialize compact and cost efficient chemical processing technology. For this separation, ultra fast thermal swing sorption is enabled by the very high rates of heat and mass transfer inherent in microchannel processing. In a first phase of the project solid adsorbents were explored. Feasibility of ultrafast thermal swing was demonstrated but the available adsorbents had insufficient differential methane capacity to achieve the required commercial economics. In a second phase, ionic liquids were adopted as absorbents of choice, and experimental work and economic analyses, performed to gauge their potential, showed promise for this novel alternative. Final conclusions suggest that a combination of a required cost target for ionic liquids or a methane capacity increase or a combination of both is required for commercialization.

  2. Swinging of two-domains vesicles in shear flow

    Science.gov (United States)

    Viallat, Annie; Tusch, Simon; Khelloufi, Kamel; Leonetti, Marc

    2014-11-01

    Giant lipid vesicles and red blood cells in shear flow at low shear rates tank tread (TT) at small viscosity ratio between the inner particle volume and the external fluid, and flip or tumble (T) at large viscosity ratio. The phase diagram of motion of red blood cells is however much more complex. Swinging superimposes to TT, cells wobble and roll rather than tumble with increasing shear rate and present a shear-rate driven transition between TT to T. These features are attributed to the shear elasticity and the non spherical stress-free shape of the cell membrane, which stores shear elastic energy as a function of the relative position of its elements. We have created vesicles with a phase diagram of motion comparable to that of red blood cells by preparing membranes with two lipids and cholesterol. These membranes present two domains separated by a contact line. The line has a tension energy that depends on its relative position on the vesicle. Similarly to red blood cells, two-domains vesicles swing and wobble. An analytical model where line tension energy is added to the Keller and Skalak's model fits our experimental data without any adjustable parameter. Our experiments and model shed light on the motion of deformable particles in shear flow.

  3. Cyclical swings: The bête noire of psychiatry.

    Science.gov (United States)

    Decker, Hannah S

    2016-02-01

    Progress in psychiatry in the West has been retarded by the proclivity of the discipline to swing violently between 2 approaches to viewing mental illness; that is, emphasizing-to the exclusion of the other-the material-somatic vs the psychical-experiential avenues to knowledge. Each time a shift occurs, the leaders of the new dominant approach emotionally denounce the principles and ideas that came before. We can examine this phenomenon historically by looking at Romantic psychiatry, mid-/late-19th century empirical psychiatry, psychoanalysis, and modern biological psychiatry. Looking at the 2 approaches in treatment today, the gold standard of patient care involves combining empirical/psychological care in 1 person (the psychiatrist) or shared between 2 clinicians working intimately with each other (psychiatrist with psychologist or social worker.) Yet as regards psychiatrists, they are discouraged from paying full attention to the psychological side by the way managed care and third-party payment have combined to remunerate them. Finally, how do we account for the intense swings and denunciations in psychiatry? The author speculates on possible explanations but leaves the question open for her readers. (c) 2016 APA, all rights reserved).

  4. Influence of simulation environment on properties of swing system

    Science.gov (United States)

    Zhang, Yu-min; Han, Yuan-yuan; Zhou, Yu-feng; Han, Jie-cai; Yao, Wang

    2007-12-01

    Swing system used in the guiding system is a kind of special equipment composed by a piece of silicon carbide mirror and a support structure made of Al alloy. In order to connect them without harm to their properties, epoxy resin is used and is solidified at room temperature. The influence of connecting process on the optical property of the mirror in swing system is studied by testing the wave-front error before and after connecting process. The results show that the connecting process under room temperature has little effect on wave-front error. The deformations of the mirror under gravity fields and thermal fields are analyzed by finite element method. The calculated results show that the surface figures under all conditions are satisfied with the requirement. The deformation of the mirror under gravity field paralleling to axial direction is the largest. When there is temperature gradient, the effect of axial temperature field on the mirror surface is much greater than that of radial temperature field.

  5. Pressure swing distillation of azeotropic mixture – A simulation study

    Directory of Open Access Journals (Sweden)

    Asma Iqbal

    2016-09-01

    Full Text Available The aim of this work is to simulate a pressure-swing distillation column for the separation and purification of ethanol from the ethanol–water binary system. The choice for this system is due to the importance of the ethanol–water separation. A steady-state equilibrium-stage model based on normalised MESH equations is used to simulate pressure-swing distillation column applied for the production of ethanol. All the work has been carried out using Aspen Plus simulator, version 13.2. Among the activity coefficient models available, the WILSON-RK model with binary parameters predicted by the Aspen Plus simulator is shown to be the most accurate to correlate the experimental vapor-/liquid equilibrium (VLE data available for the ethanol–water system. The simulation has been satisfactorily carried out for a mixture of 20 mol% ethanol in water at 1 atm pressure and 90 °C with a molar flow rate of 100 kmol/h. The adjusting parameters include D/F ratio and reflux ratio of the two columns to get water purity of 99.5 mol% from the bottom of the Low Pressure Column (LPC and the ethanol purity of 99.7 mol% from the bottom of High Pressure Column (HPC.

  6. Supplement to Resonant Rossby Wave Triads and the Swinging Spring.

    Science.gov (United States)

    Lynch, Peter

    2003-05-01

    The wave solutions discovered by Rossby are of fundamental importance for atmospheric dynamics. The nonlinear interactions between these waves determine the primary characteristics of the energy spectrum. These interactions take place between triplets of waves known as "resonant triads" and, for small amplitude, they are described by the three-wave equations. These same equations also govern the dynamics of a simple mechanical system, the elastic pendulum or swinging spring. This equivalence allows us to deduce properties, not otherwise evident, of resonant triads from the behavior of the mechanical system. In particular, the characteristic stepwise precession of the swing plane, so obvious from observation of the physical spring pendulum, is also found for the Rossby triads. This phenomenon has not been previously noted and is an example of the insight coming from the mathematical equivalence of the two systems. The implications of the precession for predictability of atmospheric motions are considered. The pattern of breakdown of unstable Rossby waves is very sensitive to unobservable details of the perturbations, making accurate prediction very difficult.

  7. Pulsation and precession of the resonant swinging spring

    Science.gov (United States)

    Lynch, Peter; Houghton, Conor

    2004-03-01

    When the frequencies of the elastic and pendular oscillations of an elastic pendulum or swinging spring are in the ratio 2:1, there is a regular exchange of energy between the two modes of oscillation. We refer to this phenomenon as pulsation. Between the horizontal excursions, or pulses, the spring undergoes a change of azimuth which we call the precession angle. The pulsation and stepwise precession are the characteristic features of the dynamics of the swinging spring. The modulation equations for the small-amplitude resonant motion of the system are the well-known three-wave equations. We use Hamiltonian reduction to determine a complete analytical solution. The amplitudes and phases are expressed in terms of both Weierstrass and Jacobi elliptic functions. The strength of the pulsation may be computed from the invariants of the equations. Several analytical formulas are found for the precession angle. We deduce simplified approximate expressions, in terms of elementary functions, for the pulsation amplitude and precession angle and demonstrate their high accuracy by numerical experiments. Thus, for given initial conditions, we can describe the envelope dynamics without solving the equations. Conversely, given the parameters which determine the envelope, we can specify initial conditions which, to a high level of accuracy, yield this envelope.

  8. Resonant Rossby Wave Triads and the Swinging Spring.

    Science.gov (United States)

    Lynch, Peter

    2003-05-01

    The wave solutions discovered by Rossby are of fundamental importance for atmospheric dynamics. The nonlinear interactions between these waves determine the primary characteristics of the energy spectrum. These interactions take place between triplets of waves known as "resonant triads" and, for a small amplitude, they are described by the three-wave equations. These same equations also govern the dynamics of a simple mechanical system, the elastic pendulum or swinging spring. This equivalence allows us to deduce properties, not otherwise evident, of resonant triads from the behavior of the mechanical system. In particular, the characteristic stepwise precession of the swing plane, so obvious from observation of the physical spring pendulum, is also found for the Rossby triads. This phenomenon has not been previously noted and is an example of the insight coming from the mathematical equivalence of the two systems. The implications of the precession for predictability of atmospheric motions are considered. The pattern of breakdown of unstable Rossby waves is very sensitive to unobservable details of the perturbations, making accurate prediction very difficult.

  9. Energy harvesting from human motion: exploiting swing and shock excitations

    International Nuclear Information System (INIS)

    Ylli, K; Hoffmann, D; Willmann, A; Becker, P; Folkmer, B; Manoli, Y

    2015-01-01

    Modern compact and low power sensors and systems are leading towards increasingly integrated wearable systems. One key bottleneck of this technology is the power supply. The use of energy harvesting techniques offers a way of supplying sensor systems without the need for batteries and maintenance. In this work we present the development and characterization of two inductive energy harvesters which exploit different characteristics of the human gait. A multi-coil topology harvester is presented which uses the swing motion of the foot. The second device is a shock-type harvester which is excited into resonance upon heel strike. Both devices were modeled and designed with the key constraint of device height in mind, in order to facilitate the integration into the shoe sole. The devices were characterized under different motion speeds and with two test subjects on a treadmill. An average power output of up to 0.84 mW is achieved with the swing harvester. With a total device volume including the housing of 21 cm 3 a power density of 40 μW cm −3 results. The shock harvester generates an average power output of up to 4.13 mW. The power density amounts to 86 μW cm −3 for the total device volume of 48 cm 3 . Difficulties and potential improvements are discussed briefly. (paper)

  10. Development of swing-free / shock free crane

    International Nuclear Information System (INIS)

    Yoon, J. S.; Park, B. S.; Kim, S. H.; Kwon, D. A.; Kim, D. W.; Kim, J. H.; Jeon, B. K.; Lee, Y. E.; Lee, S. H.

    1999-04-01

    To develop the automatized crane and to apply the relevant technology to nuclear power plants, in this project and automatized crane control system is developed along with a swing and shock crane. Also, this technology has been transferred to Bando Machinery Co. Ltd. The drive mechanism of crane is designed by adopting vector drives which provide soft acceleration and deceleration characteristics. Also, radio modems and a long-range laser displacement sensor which are commercially available are introduced to accommodate the large scaled crane systems. Also, several devices are developed for the automation of crane system. These are a crane controller, a supervisory controller, a angle measuring device, and laser localizer, a drum grapple device, and crane supervisory program. The performance of developed crane system is revealed to rapidly reduce the residual swing of the transported object and precisely controls the object position in any case. Also, the laser localizer provides he capability of measuring any arbitrary located objects within 3 cm error range

  11. Bridge resource program.

    Science.gov (United States)

    2013-09-01

    The mission of Rutgers Universitys Center for Advanced Infrastructure and Transportation (CAIT) Bridge Resource Program (BRP) is to provide bridge engineering support to the New Jersey Department of Transportation (NJDOT)s Bridge Engineering an...

  12. Swing Once More: Relating Timing and Tempo in Expert Jazz Drumming

    NARCIS (Netherlands)

    Honing, H.; de Haas, W.B.|info:eu-repo/dai/nl/304841250

    2008-01-01

    Swing refers to a characteristic long-short subdivision of the beat that is generally considered a crucial aspect that contributes to the quality of a jazz or pop performance. The current study measures this pattern (referred to as the ‘swing ratio’) at different tempi in jazz drumming. The

  13. Swing once more: Relating timing and tempo in expert jazz drumming

    NARCIS (Netherlands)

    Honing, H.; de Haas, W.B.

    2008-01-01

    Swing refers to a characteristic long-short subdivision of the beat that is generally considered a crucial aspect that contributes to the quality of a jazz or pop performance. The current study measures this pattern (referred to as the 'swing ratio') at different tempi in jazz drumming. The

  14. Cycle-to-cycle control of swing phase of paraplegic gait induced by surface electrical stimulation

    NARCIS (Netherlands)

    Franken, H.M.; Franken, H.M.; Veltink, Petrus H.; Baardman, G.; Redmeijer, R.A.; Boom, H.B.K.

    1995-01-01

    Parameterised swing phase of gait in paraplegics was obtained using surface electrical stimulation of the hip flexors, hamstrings and quadriceps; the hip flexors were stimulated to obtain a desired hip angle range, the hamstrings to provide foot clearance in the forward swing, and the quadriceps to

  15. Power Swing Detection in UPFC-Compensated Line by Phase Angle of Current

    DEFF Research Database (Denmark)

    Khodaparast, Jalal; Khederzadeh, M.; Silva, Filipe Miguel Faria da

    2017-01-01

    condition. The results show that these indices may no longer work in systems with UPFC. In addition, this paper proposes a new method for detecting power swing based on the phase angle of current at relay point and compares it with two other methods. The new method distinguishes power swing from a fault...

  16. How Do Batters Use Visual, Auditory, and Tactile Information about the Success of a Baseball Swing?

    Science.gov (United States)

    Gray, Rob

    2009-01-01

    Bat/ball contact produces visual (the ball leaving the bat), auditory (the "crack" of the bat), and tactile (bat vibration) feedback about the success of the swing. We used a batting simulation to investigate how college baseball players use visual, tactile, and auditory feedback. In Experiment 1, swing accuracy (i.e., the lateral separation…

  17. The Effect of Kettlebell Swing Load and Cadence on Physiological, Perceptual and Mechanical Variables

    Directory of Open Access Journals (Sweden)

    Michael J. Duncan

    2015-08-01

    Full Text Available This study compared the physiological, perceptual and mechanical responses to kettlebell swings at different loads and swing speeds. Following familiarization 16 strength trained participants (10 males, six females, mean age ± SD = 23 ± 2.9 performed four trials: 2 min kettlebell swings with an 8 kg kettlebell at a fast cadence; 2 min kettlebell swings with an 8 kg kettlebell at a slow cadence; 4 min kettlebell swings with a 4 kg kettlebell at a fast cadence; 4 min kettlebell swings with a 4 kg kettlebell at a slow cadence. Repeated measured analysis of variance indicated no significant differences in peak blood lactate or peak net vertical force across loads and cadences (P > 0.05. Significant main effect for time for heart rate indicated that heart rate was higher at the end of each bout than at mid-point (P = 0.001. A significant Load X cadence interaction for rating of perceived exertion (RPE (P = 0.030 revealed that RPE values were significantly higher in the 8 kg slow cadence condition compared to the 4 kg slow (P = 0.002 and 4 kg fast (P = 0.016 conditions. In summary, this study indicates that the physiological and mechanical responses to kettlebell swings at 4 kg and 8 kg loads and at fast and slow cadence were similar, whereas the perceptual response is greater when swinging an 8 kg kettlebell at slow cadence.

  18. A low-power multi port register file design using a low-swing strategy

    International Nuclear Information System (INIS)

    Yan Hao; Liu Yan; Hua Siliang; Wang Donghui; Hou Chaohuan

    2012-01-01

    A low-power register file is designed by using a low-swing strategy and modified NAND address decoders. The proposed low-swing strategy is based on the feedback scheme and uses dynamic logic to reduce the active feedback power. This method contains two parts: WRITE and READ strategy. In the WRITE low-swing scheme, the modified memory cell is used to support low-swing WRITE. The modified NAND decoder not only dissipates less power, but also enables a great deal of area reduction. Compared with the conventional single-ended register file, the low-swing strategy saves 34.5% and 51.15% bit-line power in WRITE and READ separately. The post simulation results indicate a 39.4% power improvement when the twelve ports are all busy. (semiconductor integrated circuits)

  19. Investigation of the Linker Swing Motion in the Zeolitic Imidazolate Framework ZIF-90

    KAUST Repository

    Zheng, Bin

    2018-03-13

    The linker swing motion in the zeolitic imidazolate framework ZIF-90 is investigated by density functional theory (DFT) calculation, molecular dynamics (MD) and grand-canonical Monte Carlo (GCMC) simulations. The relation between the terminal aldehyde group rotation and the linker swing motion is revealed. The extremely high activation energy of the linker swing motion in ZIF-90 can be attributed to the asymmetric geometry and electron distribution of aldehyde groups. The change in the gate structure resulting from the linker rotation is used to understand the guest adsorption in ZIF-90. This study shows that it is possible to tune the linker swing motion and then the properties of ZIF-90 by manipulating the terminal group rotation. The results highlight the importance of considering the internal freedom effects to correctly describe the linker swing motion and the flexibility of metal-organic frameworks (MOFs).

  20. Analysis of Golf Swing Motion and Applied Loads on the Human Body Using Soft-Golf TM Club

    International Nuclear Information System (INIS)

    Kwak, Ki Young; So, Ha Ju; Kim, Sung Hyeon; Kim, Dong Wook; Kim, Nam Gyun

    2011-01-01

    The purpose of this study was to analyze the kinetic effect of Soft-golf TM instrument on the human body structure. To analyze the kinetic effect of Soft-golf TM instrument, Golf swing using Soft-golf TM instrument and regular golf instrument was captured. And then Upper limbs and lumbar joint torques was calculated via computer simulation. Five man participated this study. Subjects performed golf swing using a regular golf and Soft-golf TM instrument. Golf swing motion was captured using three position sensor, active infrared LED maker and force plate. Golf swing model was generated and simulated using ADAMS/LifeMOD program. As a results, joint torque during Soft-golf swing were lower than regular golf swing. Thus soft-golf swing have joint load lower than regular golf swing and contribute to reduce joint injury

  1. Development of swing-free / shock free crane

    Energy Technology Data Exchange (ETDEWEB)

    Yoon, J. S.; Park, B. S.; Kim, S. H.; Kwon, D. A.; Kim, D. W.; Kim, J. H.; Jeon, B. K. [Korea Atomic Research Institute, Taejon (Korea, Republic of); Lee, Y. E.; Lee, S. H. [Bando Machinery Co., Taejon (Korea, Republic of)

    1999-04-01

    To develop the automatized crane and to apply the relevant technology to nuclear power plants, in this project and automatized crane control system is developed along with a swing and shock crane. Also, this technology has been transferred to Bando Machinery Co. Ltd. The drive mechanism of crane is designed by adopting vector drives which provide soft acceleration and deceleration characteristics. Also, radio modems and a long-range laser displacement sensor which are commercially available are introduced to accommodate the large scaled crane systems. Also, several devices are developed for the automation of crane system. These are a crane controller, a supervisory controller, a angle measuring device, and laser localizer, a drum grapple device, and crane supervisory program. The performance of developed crane system is revealed to rapidly reduce the residual swingof the transported object and precisely controls the object position in any case. Also, the laser localizer provides he capability of measuring any arbitrary located objects within 3 cm error range.

  2. AIR SEPARATION BY PRESSURE SWING ADSORPTION USING SUPERIOR ADSORBENTS

    Energy Technology Data Exchange (ETDEWEB)

    Ralph T. Yang

    2001-08-31

    Li-X zeolite (Si/Al = 1.0) is currently the best sorbent for use in the separation of air by adsorption processes. In particular, pressure swing adsorption (PSA) using zeolite sorbents is being increasingly used for air separation. Silver is also known to strongly affect the adsorptive properties of zeolites; and it is known that thermal vacuum dehydration of silver zeolites leads to the formation of silver clusters within the zeolite. In this work we have synthesized type X zeolites containing Ag and also varying mixtures of Li and Ag. In this project, we developed the Ag-containing zeolite as the best sorbent for air separation. We have also studied Co-ligand compounds as oxygen-selective sorbents. Syntheses, structural characterization and adsorption properties have been performed on all sorbents. The results are described in detail in 5 chapters.

  3. Swing-Down of 21-PWR Waste Package

    International Nuclear Information System (INIS)

    A.K. Scheider

    2001-01-01

    The objective of this calculation is to determine the structural response of the waste package (WP) swinging down from a horizontally suspended height. The WP used for that purpose is the 21-Pressurized Water Reactor (PWR) WP. The scope of this document is limited to reporting the calculation results in terms of stress intensities. This calculation is associated with the WP design and was performed by the Waste Package Design group in accordance with the ''Technical Work Plan for: Waste Package Design Description for LA'' (Ref. 13). AP-3.12Q, ''Calculations'' (Ref. 18) is used to perform the calculation and develop the document. The information provided by the sketches attached to this calculation is that of the potential design of the type of 21-PWR WP design considered in this calculation and provides the potential dimensions and materials for the 21-PWR WP design

  4. Effects of Aging on Arm Swing during Gait: The Role of Gait Speed and Dual Tasking.

    Science.gov (United States)

    Mirelman, Anat; Bernad-Elazari, Hagar; Nobel, Tomer; Thaler, Avner; Peruzzi, Agnese; Plotnik, Meir; Giladi, Nir; Hausdorff, Jeffrey M

    2015-01-01

    Healthy walking is characterized by pronounced arm swing and axial rotation. Aging effects on gait speed, stride length and stride time variability have been previously reported, however, less is known about aging effects on arm swing and axial rotation and their relationship to age-associated gait changes during usual walking and during more challenging conditions like dual tasking. Sixty healthy adults between the ages of 30-77 were included in this study designed to address this gap. Lightweight body fixed sensors were placed on each wrist and lower back. Participants walked under 3 walking conditions each of 1 minute: 1) comfortable speed, 2) walking while serially subtracting 3's (Dual Task), 3) walking at fast speed. Aging effects on arm swing amplitude, range, symmetry, jerk and axial rotation amplitude and jerk were compared between decades of age (30-40; 41-50; 51-60; 61-77 years). As expected, older adults walked slower (p = 0.03) and with increased stride variability (p = 0.02). Arm swing amplitude decreased with age under all conditions (p = 0.04). In the oldest group, arm swing decreased during dual task and increased during the fast walking condition (parm swing asymmetry increased during the dual task in the older groups (parm swing jerk (parm swing amplitude of the dominant arm, arm swing asymmetry and axial rotation jerk were all independent predictors of age in a multivariate model. These findings suggest that the effects of gait speed and dual tasking on arm swing and axial rotation during walking are altered among healthy older adults. Follow-up work is needed to examine if these effects contribute to reduced stability in aging.

  5. "Speaking a Secret Language:" West Coast Swing as a Community of Practice of Informal and Incidental Learners

    Science.gov (United States)

    Callahan, Jamie L.

    2005-01-01

    This study reports the findings of a qualitative study of competitive West Coast Swing dancers that incorporated both ethnographic and phenomenological techniques. A modern variation of the original Lindy Hop, West Coast Swing is typically learned in dance studios and non-profit clubs. The West Coast Swing community can be considered a community…

  6. Cable Supported Bridges

    DEFF Research Database (Denmark)

    Gimsing, Niels Jørgen

    Cable supported bridges in the form of suspension bridges and cable-stayed bridges are distinguished by their ability to overcome large spans.The book concentrates on the synthesis of cable supported bridges, covering both design and construction aspects. The analytical part covers simple methods...

  7. A Three-Dimensional Kinematic and Kinetic Study of the College-Level Female Softball Swing

    Directory of Open Access Journals (Sweden)

    Monica Milanovich, Steven M. Nesbit

    2014-03-01

    Full Text Available This paper quantifies and discusses the three-dimensional kinematic and kinetic characteristics of the female softball swing as performed by fourteen female collegiate amateur subjects. The analyses were performed using a three-dimensional computer model. The model was driven kinematically from subject swings data that were recorded with a multi-camera motion analysis system. Each subject used two distinct bats with significantly different inertial properties. Model output included bat trajectories, subject/bat interaction forces and torques, work, and power. These data formed the basis for a detailed analysis and description of fundamental swing kinematic and kinetic quantities. The analyses revealed that the softball swing is a highly coordinated and individual three-dimensional motion and subject-to-subject variations were significant in all kinematic and kinetic quantities. In addition, the potential effects of bat properties on swing mechanics are discussed. The paths of the hands and the centre-of-curvature of the bat relative to the horizontal plane appear to be important trajectory characteristics of the swing. Descriptions of the swing mechanics and practical implications are offered based upon these findings.

  8. Using swing resistance and assistance to improve gait symmetry in individuals post-stroke.

    Science.gov (United States)

    Yen, Sheng-Che; Schmit, Brian D; Wu, Ming

    2015-08-01

    A major characteristic of hemiplegic gait observed in individuals post-stroke is spatial and temporal asymmetry, which may increase energy expenditure and the risk of falls. The purpose of this study was to examine the effects of swing resistance/assistance applied to the affected leg on gait symmetry in individuals post-stroke. We recruited 10 subjects with chronic stroke who demonstrated a shorter step length with their affected leg in comparison to the non-affected leg during walking. They participated in two test sessions for swing resistance and swing assistance, respectively. During the adaptation period, subjects counteracted the step length deviation caused by the applied swing resistance force, resulting in an aftereffect consisting of improved step length symmetry during the post-adaptation period. In contrast, subjects did not counteract step length deviation caused by swing assistance during adaptation period and produced no aftereffect during the post-adaptation period. Locomotor training with swing resistance applied to the affected leg may improve step length symmetry through error-based learning. Swing assistance reduces errors in step length during stepping; however, it is unclear whether this approach would improve step length symmetry. Results from this study may be used to develop training paradigms for improving gait symmetry of stroke survivors. Copyright © 2015 Elsevier B.V. All rights reserved.

  9. Reconstruction of human swing leg motion with passive biarticular muscle models.

    Science.gov (United States)

    Ahmad Sharbafi, Maziar; Mohammadi Nejad Rashty, Aida; Rode, Christian; Seyfarth, Andre

    2017-04-01

    Template models, which are utilized to demonstrate general aspects in human locomotion, mostly investigate stance leg operation. The goal of this paper is presenting a new conceptual walking model benefiting from swing leg dynamics. Considering a double pendulum equipped with combinations of biarticular springs for the swing leg beside spring-mass (SLIP) model for the stance leg, a novel SLIP-based model, is proposed to explain human-like leg behavior in walking. The action of biarticular muscles in swing leg motion helps represent human walking features, like leg retraction, ground reaction force and generating symmetric walking patterns, in simulations. In order to stabilize the motion by the proposed passive structure, swing leg biarticular muscle parameters such as lever arm ratios, stiffnesses and rest lengths need to be properly adjusted. Comparison of simulation results with human experiments shows the ability of the proposed model in replicating kinematic and kinetic behavior of both stance and swing legs as well as biarticular thigh muscle force of the swing leg. This substantiates the important functional role of biarticular muscles in leg swing. Copyright © 2017 Elsevier B.V. All rights reserved.

  10. Performance analysis of power swing blocking feature in ABB 670 series impedance relays

    Directory of Open Access Journals (Sweden)

    Maciej Łosiński

    2012-12-01

    Full Text Available This paper presents test results of a distance protection’s PSD power swing detection feature in ABB 670 series relays. A RED670 relay was tested, which is part of the hydroelectric set protection in Żarnowiec Pumped Storage Plant. The power swing blocking feature’s performance was analysed on the basis of the results of object tests made with an Omicron digital tester. Also presented are simulation results that illustrate the PSD feature’s response to power swings caused by a disturbance in the power system. It is also shown how a distance protection may react to the same fault, depending on its settings.

  11. A Novel Approach to Detect Faults Occurring During Power Swings by Abrupt Change of Impedance Trajectory

    DEFF Research Database (Denmark)

    Khodaparast, Jalal; Khederzadeh, M.; Silva, Filipe Miguel Faria da

    2017-01-01

    The main purpose of power swing blocking is to distinguish faults from power swings. However, faults occurred during a power swing should still be detected and cleared promptly. This paper proposes an index based on detecting abrupt jump of impedance trajectory by utilization of the predicting...... of Taylor expansion is used to decrease the corrugation effect of impedance estimation and increase the reliability of the proposed method. Furthermore, in order to increase the selectivity of the proposed method, the proposed index is armed with phase comparison logic to detect internal faults...

  12. Bridges in complex networks.

    Science.gov (United States)

    Wu, Ang-Kun; Tian, Liang; Liu, Yang-Yu

    2018-01-01

    A bridge in a graph is an edge whose removal disconnects the graph and increases the number of connected components. We calculate the fraction of bridges in a wide range of real-world networks and their randomized counterparts. We find that real networks typically have more bridges than their completely randomized counterparts, but they have a fraction of bridges that is very similar to their degree-preserving randomizations. We define an edge centrality measure, called bridgeness, to quantify the importance of a bridge in damaging a network. We find that certain real networks have a very large average and variance of bridgeness compared to their degree-preserving randomizations and other real networks. Finally, we offer an analytical framework to calculate the bridge fraction and the average and variance of bridgeness for uncorrelated random networks with arbitrary degree distributions.

  13. Optimization and Control of Pressure Swing Adsorption Processes Under Uncertainty

    KAUST Repository

    Khajuria, Harish

    2012-03-21

    The real-time periodic performance of a pressure swing adsorption (PSA) system strongly depends on the choice of key decision variables and operational considerations such as processing steps and column pressure temporal profiles, making its design and operation a challenging task. This work presents a detailed optimization-based approach for simultaneously incorporating PSA design, operational, and control aspects under the effect of time variant and invariant disturbances. It is applied to a two-bed, six-step PSA system represented by a rigorous mathematical model, where the key optimization objective is to maximize the expected H2 recovery while achieving a closed loop product H2 purity of 99.99%, for separating 70% H2, 30% CH4 feed. The benefits over sequential design and control approach are shown in terms of closed-loop recovery improvement of more than 3%, while the incorporation of explicit/multiparametric model predictive controllers improves the closed loop performance. © 2012 American Institute of Chemical Engineers (AIChE).

  14. Hybrid markerless tracking of complex articulated motion in golf swings.

    Science.gov (United States)

    Fung, Sim Kwoh; Sundaraj, Kenneth; Ahamed, Nizam Uddin; Kiang, Lam Chee; Nadarajah, Sivadev; Sahayadhas, Arun; Ali, Md Asraf; Islam, Md Anamul; Palaniappan, Rajkumar

    2014-04-01

    Sports video tracking is a research topic that has attained increasing attention due to its high commercial potential. A number of sports, including tennis, soccer, gymnastics, running, golf, badminton and cricket have been utilised to display the novel ideas in sports motion tracking. The main challenge associated with this research concerns the extraction of a highly complex articulated motion from a video scene. Our research focuses on the development of a markerless human motion tracking system that tracks the major body parts of an athlete straight from a sports broadcast video. We proposed a hybrid tracking method, which consists of a combination of three algorithms (pyramidal Lucas-Kanade optical flow (LK), normalised correlation-based template matching and background subtraction), to track the golfer's head, body, hands, shoulders, knees and feet during a full swing. We then match, track and map the results onto a 2D articulated human stick model to represent the pose of the golfer over time. Our work was tested using two video broadcasts of a golfer, and we obtained satisfactory results. The current outcomes of this research can play an important role in enhancing the performance of a golfer, provide vital information to sports medicine practitioners by providing technically sound guidance on movements and should assist to diminish the risk of golfing injuries. Copyright © 2013 Elsevier Ltd. All rights reserved.

  15. The Motion Planning of Overhead Crane Based on Suppressing Payload Residual Swing

    Directory of Open Access Journals (Sweden)

    Liu Hua-sen

    2016-01-01

    Full Text Available Since the overhead crane system is subject to under actuation system due to that overhead crane and payload are connected by flexibility wire rope. The payload generates residual swing when the overhead crane is accelerating/ decelerating the motions. This may cause trouble for the payload precise positioning and motion planning. Hence, an optimization input shaping control method is presented to reduce the under actuated overhead crane’s payload swing caused via the inertia force. The dynamic model of the overhead crane is proposed according to the physics structure of the crane. The input shaper based on the motion planning of the crane is used as the feed forward input to suppress payload residual swing. Simulation and experiment results indicate that the ZV input shaper and ZVD input shaper can reduce the payload swing of the overhead crane.

  16. Metabolic Heat Regenerated Temperature Swing Adsorption for CO2, Thermal and Humidity Control, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Metabolic heat regenerated Temperature Swing Adsorption (MTSA) technology is proposed for a Portable Life Support System to remove and reject heat and carbon dioxide...

  17. Metabolic Heat Regenerated Temperature Swing Adsorption for CO2, Thermal and Humidity Control Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Metabolic heat regenerated Temperature Swing Adsorption (MTSA) technology is proposed for a Portable Life Support System to remove and reject heat and carbon dioxide...

  18. The effects of the arm swing on biomechanical and physiological aspects of roller ski skating.

    Science.gov (United States)

    Hegge, Ann Magdalen; Ettema, Gertjan; de Koning, Jos J; Rognstad, Asgeir Bakken; Hoset, Martin; Sandbakk, Øyvind

    2014-08-01

    This study analyzed the biomechanical and physiological effects of the arm swing in roller ski skating, and compared leg-skating (i.e. ski skating without poles) using a pronounced arm swing (SWING) with leg-skating using locked arms (LOCKED). Sixteen elite male cross-country skiers performed submaximal stages at 10, 15 and 20kmh(-1) on a 2% inclined treadmill in the two techniques. SWING demonstrated higher peak push-off forces and a higher force impulse at all speeds, but a longer cycle length only at the highest speed (all Pski skating increases the ski forces and aerobic energy cost at low and moderate speeds, whereas the greater forces at high speed lead to a longer cycle length and smaller anaerobic contribution. Copyright © 2014 Elsevier B.V. All rights reserved.

  19. Core Muscle Activation in One-Armed and Two-Armed Kettlebell Swing.

    Science.gov (United States)

    Andersen, Vidar; Fimland, Marius S; Gunnarskog, Aril; Jungård, Georg-Andrè; Slåttland, Roy-Andrè; Vraalsen, Øyvind F; Saeterbakken, Atle H

    2016-05-01

    The aim of the study was to compare the electromyographic activity of rectus abdominis, oblique external, and lower and upper erector spinae at both sides of the truncus in 1-armed and 2-armed kettlebell swing. Sixteen healthy men performed 10 repetitions of both exercises using a 16-kg kettlebell in randomized order. For the upper erector spinae, the activation of the contralateral side during 1-armed swing was 24% greater than that of the ipsilateral side during 1-armed swing (p kettlebell swing with 1 arm resulted in greater neuromuscular activity for the contralateral side of the upper erector spinae and ipsilateral side of the rectus abdominis, and lower activation of the opposite side of the respective muscles.

  20. Design and Implementation of a Bionic Mimosa Robot with Delicate Leaf Swing Behavior

    OpenAIRE

    Chung-Liang Chang; Jin-Long Shie

    2014-01-01

    This study designed and developed a bionic mimosa robot with delicate leaf swing behaviors. For different swing behaviors, this study developed a variety of situations, in which the bionic mimosa robot would display different postures. The core technologies used were Shape Memory Alloys (SMAs), plastic material, and an intelligent control device. The technology particularly focused on the SMAs memory processing bend mode, directional guidance, and the position of SMAs installed inside the pla...

  1. Effects of Kettlebell Swing vs. Explosive Deadlift Training on Strength and Power

    OpenAIRE

    Matthew R. Maulit; David C. Archer; Whitney D. Leyva; Cameron N. Munger; Megan A. Wong; Lee E. Brown; Jared W. Coburn; Andrew J. Galpin

    2017-01-01

    Background: Recent research has compared explosive deadlift to kettlebell training observing their effects on strength. The kettlebell swing is a popular practical exercise as it shares share a hip hinge movement with the explosive deadlift, but the two have not been compared. Objectives: The purpose of this study was to compare the effects of kettlebell swing vs. explosive deadlift training on strength and power. Methods: Thirty-one recreationally resistance-trained men (age = 23.1 ± 2.3 yea...

  2. Bridge element deterioration rates.

    Science.gov (United States)

    2008-10-01

    This report describes the development of bridge element deterioration rates using the NYSDOT : bridge inspection database using Markov chains and Weibull-based approaches. It is observed : that Weibull-based approach is more reliable for developing b...

  3. Movable bridge maintenance monitoring.

    Science.gov (United States)

    2013-10-01

    Movable bridges have particular maintenance issues, which cost considerably more than those of fixed bridges, : mostly because of the complex interaction of the mechanical, electrical and structural components. In order to track : maintenance and ope...

  4. LTBP bridge performance primer.

    Science.gov (United States)

    2013-12-01

    "The performance of bridges is critical to the overall performance of the highway transportation system in the United States. However, many critical aspects of bridge performance are not well understood. The reasons for this include the extreme diver...

  5. Bridge vehicle impact assessment.

    Science.gov (United States)

    2011-12-01

    Bridges in New York State have been experiencing close to 200 bridge hits a year. These : accidents are attributed to numerous factors including: improperly stored equipment on trucks; : violation of vehicle posting signs; illegal commercial vehicles...

  6. Improving bridge load rating accuracy.

    Science.gov (United States)

    2013-06-01

    Nearly one-quarter of Alabamas bridges are deemed structurally deficient or functionally obsolete. An : additional seven percent of Alabamas bridges were posted bridges in 2010. (Federal Highway Administration, : 2011) Accurate bridge load rati...

  7. Kettlebell swing training improves maximal and explosive strength.

    Science.gov (United States)

    Lake, Jason P; Lauder, Mike A

    2012-08-01

    The aim of this study was to establish the effect that kettlebell swing (KB) training had on measures of maximum (half squat-HS-1 repetition maximum [1RM]) and explosive (vertical jump height-VJH) strength. To put these effects into context, they were compared with the effects of jump squat power training (JS-known to improve 1RM and VJH). Twenty-one healthy men (age = 18-27 years, body mass = 72.58 ± 12.87 kg) who could perform a proficient HS were tested for their HS 1RM and VJH pre- and post-training. Subjects were randomly assigned to either a KB or JS training group after HS 1RM testing and trained twice a week. The KB group performed 12-minute bouts of KB exercise (12 rounds of 30-second exercise, 30-second rest with 12 kg if 70 kg). The JS group performed at least 4 sets of 3 JS with the load that maximized peak power-Training volume was altered to accommodate different training loads and ranged from 4 sets of 3 with the heaviest load (60% 1RM) to 8 sets of 6 with the lightest load (0% 1RM). Maximum strength improved by 9.8% (HS 1RM: 165-181% body mass, p < 0.001) after the training intervention, and post hoc analysis revealed that there was no significant difference between the effect of KB and JS training (p = 0.56). Explosive strength improved by 19.8% (VJH: 20.6-24.3 cm) after the training intervention, and post hoc analysis revealed that the type of training did not significantly affect this either (p = 0.38). The results of this study clearly demonstrate that 6 weeks of biweekly KB training provides a stimulus that is sufficient to increase both maximum and explosive strength offering a useful alternative to strength and conditioning professionals seeking variety for their athletes.

  8. Effects of Aging on Arm Swing during Gait: The Role of Gait Speed and Dual Tasking.

    Directory of Open Access Journals (Sweden)

    Anat Mirelman

    Full Text Available Healthy walking is characterized by pronounced arm swing and axial rotation. Aging effects on gait speed, stride length and stride time variability have been previously reported, however, less is known about aging effects on arm swing and axial rotation and their relationship to age-associated gait changes during usual walking and during more challenging conditions like dual tasking. Sixty healthy adults between the ages of 30-77 were included in this study designed to address this gap. Lightweight body fixed sensors were placed on each wrist and lower back. Participants walked under 3 walking conditions each of 1 minute: 1 comfortable speed, 2 walking while serially subtracting 3's (Dual Task, 3 walking at fast speed. Aging effects on arm swing amplitude, range, symmetry, jerk and axial rotation amplitude and jerk were compared between decades of age (30-40; 41-50; 51-60; 61-77 years. As expected, older adults walked slower (p = 0.03 and with increased stride variability (p = 0.02. Arm swing amplitude decreased with age under all conditions (p = 0.04. In the oldest group, arm swing decreased during dual task and increased during the fast walking condition (p<0.0001. Similarly, arm swing asymmetry increased during the dual task in the older groups (p<0.004, but not in the younger groups (p = 0.67. Significant differences between groups and within conditions were observed in arm swing jerk (p<0.02, axial rotation amplitude (p<0.02 and axial jerk (p<0.001. Gait speed, arm swing amplitude of the dominant arm, arm swing asymmetry and axial rotation jerk were all independent predictors of age in a multivariate model. These findings suggest that the effects of gait speed and dual tasking on arm swing and axial rotation during walking are altered among healthy older adults. Follow-up work is needed to examine if these effects contribute to reduced stability in aging.

  9. Progressing MoodSwings. The upgrade and evaluation of MoodSwings 2.0: An online intervention for bipolar disorder.

    Science.gov (United States)

    Lauder, S; Cosgrove, V E; Gliddon, E; Grimm, D; Dodd, S; Berk, L; Castle, D; Suppes, T S; Berk, M

    2017-05-01

    MoodSwings 2.0 is a self-guided online intervention for bipolar disorder. The intervention incorporates technological improvements on an earlier validated version of the intervention (MoodSwings 1.0). The previous MoodSwings trial provides this study with a unique opportunity to progress previous work, whilst being able to take into consideration lesson learnt, and technological enhancements. The structure and technology of MoodSwings 2.0 are described and the relevance to other online health interventions is highlighted. An international team from Australia and the US updated and improved the programs content pursuant to changes in DSM-5, added multimedia components and included larger numbers of participants in the group discussion boards. Greater methodological rigour in this trial includes an attention control condition, quarterly telephone assessments, and red flag alerts for significant clinical change. This paper outlines these improvements, including additional security and safety measures. A 3 arm RCT is currently evaluating the enhanced program to assess the efficacy of MS 2.0; the primary outcome is change in depressive and manic symptoms. To our knowledge this is the first randomized controlled online bipolar study with a discussion board attention control and meets the key methodological criteria for online interventions. Copyright © 2017. Published by Elsevier Inc.

  10. Ground reaction forces produced by two different hockey skating arm swing techniques.

    Science.gov (United States)

    Hayward-Ellis, Julie; Alexander, Marion J L; Glazebrook, Cheryl M; Leiter, Jeff

    2017-10-01

    The arm swing in hockey skating can have a positive effect on the forces produced by each skate, and the resulting velocity from each push off. The main purpose of this study was to measure the differences in ground reaction forces (GRFs) produced from an anteroposterior versus a mediolateral style hockey skating arm swing. Twenty-four elite-level female hockey players performed each technique while standing on a ground-mounted force platform, and all trials were filmed using two video cameras. Force data was assessed for peak scaled GRFs in the frontal and sagittal planes, and resultant GRF magnitude and direction. Upper limb kinematics were assessed from the video using Dartfish video analysis software, confirming that the subjects successfully performed two distinct arm swing techniques. The mediolateral arm swing used a mean of 18.38° of glenohumeral flexion/extension and 183.68° of glenohumeral abduction/adduction while the anteroposterior technique used 214.17° and 28.97° respectively. The results of this study confirmed that the mediolateral arm swing produced 37% greater frontal plane and 33% less sagittal plane GRFs than the anteroposterior arm swing. The magnitudes of the resultant GRFs were not significantly different between the two techniques; however, the mediolateral technique produced a resultant GRF with a significantly larger angle from the direction of travel (44.44°) as compared to the anteroposterior technique (31.60°). The results of this study suggest that the direction of GRFs produced by the mediolateral arm swing more closely mimic the direction of lower limb propulsion during the skating stride.

  11. A comparative study of two different uncinectomy techniques: swing-door and classical.

    Science.gov (United States)

    Singhania, Ankit A; Bansal, Chetan; Chauhan, Nirali; Soni, Saurav

    2012-01-01

    The aim of this study was to determine which technique of uncinectomy, classical or swing door technique. Four hundred eighty Cases of sinusitis were selected and operated for Functional Endoscopic Sinus Surgery (FESS). Out of these, in 240 uncinectomies classical uncinectomy was done whereas in another 240 uncinectomies swing door technique was used. Initially patients were medically managed treated according to their symptoms and prior management. Patients who had received previous adequate medical management were evaluated with CT scan of the sinuses. If disease still persists than they were operated for FESS. The authors' experience indicates that Functional endoscopic sinus surgery can be performed under local or general anesthesia, as permitted or tolerated. In this review classical technique was used in 240 uncinectomies. Out of this, ethmoidal complex injury was noted in 4 cases, missed maxillary ostium syndrome (incomplete removal) was reported in 12 patients and orbital fat exposure was encountered in 5 patients. As compared to 240 uncinectomies done with swing door technique, incomplete removal was evident in 2 cases and lacrimal duct injury was reported in 3 cases. 'Evidence that underscores how this 'swing door technique' successfully combines 'the conservation goals of the anterior-to-posterior approach and anatomic virtues of the posterior-to-anterior approach to ethmoidectomy of the total 480 uncinectomies operated. Out of which 240 uncinectomies have been performed using the 'swing-door' technique. The 240 uncinectomies performed using classical technique were used as controls. The incidence of orbital penetration, incomplete removal, ethmoidal complex injury and ostium non-identification was significantly less with the new technique. Three lacrimal injuries occurred with the 'swing-door' technique compared to no injuries with classical technique. The authors recommend swing door technique as it is easy to learn, allows complete removal of the

  12. A Comparative Study of Two Different Uncinectomy Techniques: Swing-Door and Classical

    Directory of Open Access Journals (Sweden)

    Ankit A Singhania

    2011-01-01

    Full Text Available Introduction: The aim of this study was to determine which technique of uncinectomy, classical or swing door technique.  Materials and Methods: Four hundred eighty Cases of sinusitis were selected and operated for Functional Endoscopic Sinus Surgery (FESS. Out of these, in 240 uncinectomies classical uncinectomy was done whereas in another 240 uncinectomies swing door technique was used. Initially patients were medically managed treated according to their symptoms and prior management. Patients who had received previous adequate medical management were evaluated with CT scan of the sinuses. If disease still persists than they were operated for FESS. Results: The authors' experience indicates that Functional endoscopic sinus surgery can be performed under local or general anesthesia, as permitted or tolerated. In this review classical technique was used in 240 uncinectomies. Out of this, ethmoidal complex injury was noted in 4 cases, missed maxillary ostium syndrome (incomplete removal was reported in 12 patients and orbital fat exposure was encountered in 5 patients. As compared to 240 uncinectomies done with swing door technique, incomplete removal was evident in 2 cases and lacrimal duct injury was reported in 3 cases. 'Evidence that underscores how this 'swing door technique' successfully combines 'the conservation goals of the anterior-to-posterior approach and anatomic virtues of the posterior-to-anterior approach to ethmoidectomy of the total 480 uncinectomies operated. Out of which 240 uncinectomies have been performed using the 'swing-door' technique. The 240 uncinectomies performed using classical technique were used as controls. The incidence of orbital penetration, incomplete removal, ethmoidal complex injury and ostium non-identification was significantly less with the new technique. Three lacrimal injuries occurred with the 'swing-door' technique compared to no injuries with classical technique. Conclusion: The authors recommend

  13. Mechanical loading of the gymnast’s motor system during swings on rings

    Directory of Open Access Journals (Sweden)

    R Serafin

    2008-12-01

    Full Text Available The aim of this work was to identify the mechanical loading of the gymnast’s motor system during forward and backward swings on gymnastic rings. A junior gymnast of the First Class, aged 14, with body mass 53.1 kg and body length 1.61 m, participated in the study. He executed a series of ten cyclic swing movements on rings with his maximum amplitude. Kinematic variables of the gymnast’s centre of mass (COM as well as reaction forces in the cables were measured and synchronized using the SIMI MOTION movement analysis system. Two separate phases of mechanical loading of the motor system have been identified: resistance phase and non resistance phase. In the non resistance phase the gymnast attains similar values of the COM’s momentum but different angular displacements. In the resistance phase the forces acting on the motor system have their maximum. They amount to 5.5 BW for the forward swing and 6.5 BW for the backward swing movement. The maximum rate of change of the force for forward and backward swing is 42.6 BWs-1 and 67.4 BWs-1, respectively. These two variables differentiate the mechanical loading of the gymnast’s motor system between forward and backward swings. The reaction force produced by the gymnast is significantly greater during the execution of forward swings. It seems probable that horizontal displacements of COM may be the factor responsible for reduction of the mechanical loading experienced by the gymnast.

  14. Nonlinear dynamic response of cable-suspended systems under swinging and heaving motion

    International Nuclear Information System (INIS)

    Cao, Guohua; Wang, Naige; Wang, Lei; Zhu, Zhencai

    2017-01-01

    In order to enhance the fidelity, convenient and flexibility of swinging motion, the structure of incompletely restrained cablesuspended system controlled by two drums was proposed, and the dynamic response of the system under swinging and heaving motion were investigated in this paper. The cables are spatially discretized using the assumed modes method and the system equations of motion are derived by Lagrange equations of the first kind. Based on geometric boundary conditions and linear complementary theory, the differential algebraic equations are transformed to a set of classical difference equations. Nonlinear dynamic behavior occurs under certain range of rotational velocity and frequency. The results show that asynchronous motion of suspension platform is easily caused imbalance for cable tension. Dynamic response of different swing frequencies were obtained via power frequency analysis, which could be used in the selection of the working frequency of the swing motion. The work will contribute to a better understanding of the swing frequency, cable tension and posture with dynamic characteristics of unilateral geometric and kinematic constraints in this system, and it is also useful to investigate the accuracy and reliability of instruments in future.

  15. Effects of constrained arm swing on vertical center of mass displacement during walking.

    Science.gov (United States)

    Yang, Hyung Suk; Atkins, Lee T; Jensen, Daniel B; James, C Roger

    2015-10-01

    The purpose of this study was to determine the effects of constraining arm swing on the vertical displacement of the body's center of mass (COM) during treadmill walking and examine several common gait variables that may account for or mask differences in the body's COM motion with and without arm swing. Participants included 20 healthy individuals (10 male, 10 female; age: 27.8 ± 6.8 years). The body's COM displacement, first and second peak vertical ground reaction forces (VGRFs), and lowest VGRF during mid-stance, peak summed bilateral VGRF, lower extremity sagittal joint angles, stride length, and foot contact time were measured with and without arm swing during walking at 1.34 m/s. The body's COM displacement was greater with the arms constrained (arm swing: 4.1 ± 1.2 cm, arm constrained: 4.9 ± 1.2 cm, p arm COM acceleration might have contributed to the difference. These findings indicate that a change in arm swing causes differences in vertical COM displacement, which could increase energy expenditure. Copyright © 2015 Elsevier B.V. All rights reserved.

  16. Rhythmic arm swing enhances patterned locomotor-like muscle activity in passively moved lower extremities

    Science.gov (United States)

    Ogawa, Tetsuya; Sato, Takahiko; Ogata, Toru; Yamamoto, Shin-Ichiro; Nakazawa, Kimitaka; Kawashima, Noritaka

    2015-01-01

    The use of driven gait orthosis (DGO) has drawn attention in gait rehabilitation for patients after central nervous system (CNS) lesions. By imposing a passive locomotor-like kinematic pattern, the neural mechanisms responsible for locomotion can be activated as in a normal gait. To further enhance this activity, discussions on possible intervention are necessary. Given the possible functional linkages between the upper and lower limbs, we investigated in healthy subjects the degree of modification in the lower limb muscles during DGO-induced passive gait by the addition of swing movement in the upper extremity. The results clearly showed that muscle activity in the ankle dorsiflexor TA muscle was significantly enhanced when the passive locomotor-like movement was accompanied by arm swing movement. The modifications in the TA activity were not a general increase through the stride cycles, but were observed under particular phases as in normal gaits. Voluntary effort to swing the arms may have certain effects on the modification of the muscle activity. The results provide clinical implications regarding the usefulness of voluntary arm swing movement as a possible intervention in passive gait training using DGO, since ordinary gait training using DGO does not induce spontaneous arm swing movement despite its known influence on the lower limb movement. PMID:25742956

  17. Target of physiological gait: Realization of speed adaptive control for a prosthetic knee during swing flexion.

    Science.gov (United States)

    Cao, Wujing; Yu, Hongliu; Zhao, Weiliang; Li, Jin; Wei, Xiaodong

    2017-10-13

    Prosthetic knee is the most important component of lower limb prosthesis. Speed adaptive for prosthetic knee during swing flexion is the key method to realize physiological gait. This study aims to discuss the target of physiological gait, propose a speed adaptive control method during swing flexion and research the damping adjustment law of intelligent hydraulic prosthetic knee. According to the physiological gait trials of healthy people, the control target during swing flexion is defined. A new prosthetic knee with fuzzy logical control during swing flexion is designed to realize the damping adjustment automatically. The function simulation and evaluation system of intelligent knee prosthesis is provided. Speed adaptive control test of the intelligent prosthetic knee in different velocities are researched. The maximum swing flexion of the knee angle is set between sixty degree and seventy degree as the target of physiological gait. Preliminary experimental results demonstrate that the prosthetic knee with fuzzy logical control is able to realize physiological gait under different speeds. The faster the walking, the bigger the valve closure percentage of the hydraulic prosthetic knee. The proposed fuzzy logical control strategy and intelligent hydraulic prosthetic knee are effective for the amputee to achieve physiological gait.

  18. Increasing cognitive load attenuates right arm swing in healthy human walking

    Science.gov (United States)

    Killeen, Tim; Easthope, Christopher S.; Filli, Linard; Lőrincz, Lilla; Schrafl-Altermatt, Miriam; Brugger, Peter; Linnebank, Michael; Curt, Armin; Zörner, Björn; Bolliger, Marc

    2017-01-01

    Human arm swing looks and feels highly automated, yet it is increasingly apparent that higher centres, including the cortex, are involved in many aspects of locomotor control. The addition of a cognitive task increases arm swing asymmetry during walking, but the characteristics and mechanism of this asymmetry are unclear. We hypothesized that this effect is lateralized and a Stroop word-colour naming task-primarily involving left hemisphere structures-would reduce right arm swing only. We recorded gait in 83 healthy subjects aged 18-80 walking normally on a treadmill and while performing a congruent and incongruent Stroop task. The primary measure of arm swing asymmetry-an index based on both three-dimensional wrist trajectories in which positive values indicate proportionally smaller movements on the right-increased significantly under dual-task conditions in those aged 40-59 and further still in the over-60s, driven by reduced right arm flexion. Right arm swing attenuation appears to be the norm in humans performing a locomotor-cognitive dual-task, confirming a prominent role of the brain in locomotor behaviour. Women under 60 are surprisingly resistant to this effect, revealing unexpected gender differences atop the hierarchical chain of locomotor control.

  19. Kinetic and Kinematic Differences in a Golf Swing in One and Both Lower Limb Amputees

    Directory of Open Access Journals (Sweden)

    Stastny Petr

    2015-12-01

    Full Text Available Amputee golfers need to cope with the absence of sole proprioception, a decreased range of swing motion and other factors which should be recognized for training purposes. The aim of this study was to determine the kinetic and kinematic differences in the golf swing in one leg and two legs amputees. The participants consisted of two males and one female at a professional or amateur level with a different degree of disability. Each participant was taped by 3D markers and performed five golf swings with the iron 6. The intraclass correlation coefficient (ICC did not vary between individuals in kinematics, however, it was low in kinetic variables of two leg amputees. The Kendal rank correlation showed a significant relationship between the level of amputation and a large number of kinetic and kinematic variables such as X factor, O factor, S factor and individual body angles. The fluency and similarity of the golf swing did not depend on the level of amputation. One lower limb amputation did not seem to increase movement variability contrary to two lower limb amputation. The most variable parameter was a weight-shift in all golfers. The takeaway and horizontal force angle depended on the level of amputation rather than individual technique, thus, their modification by training may be difficult. Estimation of golf swing „mistakes“ in amputees in respect to the leading arm in an early follow or late follow position appeared to be useless.

  20. Nonlinear dynamic response of cable-suspended systems under swinging and heaving motion

    Energy Technology Data Exchange (ETDEWEB)

    Cao, Guohua; Wang, Naige; Wang, Lei; Zhu, Zhencai [China University of Mining and Technology, Xuzhou (China)

    2017-07-15

    In order to enhance the fidelity, convenient and flexibility of swinging motion, the structure of incompletely restrained cablesuspended system controlled by two drums was proposed, and the dynamic response of the system under swinging and heaving motion were investigated in this paper. The cables are spatially discretized using the assumed modes method and the system equations of motion are derived by Lagrange equations of the first kind. Based on geometric boundary conditions and linear complementary theory, the differential algebraic equations are transformed to a set of classical difference equations. Nonlinear dynamic behavior occurs under certain range of rotational velocity and frequency. The results show that asynchronous motion of suspension platform is easily caused imbalance for cable tension. Dynamic response of different swing frequencies were obtained via power frequency analysis, which could be used in the selection of the working frequency of the swing motion. The work will contribute to a better understanding of the swing frequency, cable tension and posture with dynamic characteristics of unilateral geometric and kinematic constraints in this system, and it is also useful to investigate the accuracy and reliability of instruments in future.

  1. Cardiovascular and Metabolic Demads of the Kettlebell Swing using Tabata Interval versus a Traditional Resistance Protocol.

    Science.gov (United States)

    Fortner, Howard A; Salgado, Jeanette M; Holmstrup, Angelica M; Holmstrup, Michael E

    Tabata (TAB) training, consisting of eight cycles of 20 seconds of maximal exercise followed by 10 seconds of rest, is time-efficient, with aerobic and anaerobic benefit. This study investigated the cardiovascular and metabolic demands of a TAB versus traditional (TRAD) resistance protocol with the kettlebell swing. Fourteen young (18-25y), non-obese (BMI 25.7±0.8 kg/m 2 ) participants reported on three occasions. All testing incorporated measurements of HR, oxygen consumption, and blood lactate accumulation. Each participant completed Tabata kettlebell swings (male- 8kg, female- 4.5kg; 8 intervals; 20s maximal repetitions, 10s rest). On a subsequent visit (TRAD), the total swings from the TAB protocol were evenly divided into 4 sets, with 90s rest between sets. Outcome measures were compared using paired t-tests. The TAB was completed more quickly than the TRAD protocol (240.0±0.0 v. 521.5±3.3 sec, Pkettlebell swing demonstrated significantly greater cardiovascular and metabolic responses within a TAB vs. TRAD framework. Appropriate screening and risk stratification are advised before implementing kettlebell swings.

  2. Design and Implementation of a Bionic Mimosa Robot with Delicate Leaf Swing Behavior

    Directory of Open Access Journals (Sweden)

    Chung-Liang Chang

    2014-12-01

    Full Text Available This study designed and developed a bionic mimosa robot with delicate leaf swing behaviors. For different swing behaviors, this study developed a variety of situations, in which the bionic mimosa robot would display different postures. The core technologies used were Shape Memory Alloys (SMAs, plastic material, and an intelligent control device. The technology particularly focused on the SMAs memory processing bend mode, directional guidance, and the position of SMAs installed inside the plastic material. Performance analysis and evaluation were conducted using two SMAs for mimosa opening/closing behaviors. Finally, by controlling the mimosa behavior with a micro-controller, the optimal strain swing behavior was realized through fuzzy logic control in order to display the different postures of mimosa under different situations. The proposed method is applicable to micro-bionic robot systems, entertainment robots, biomedical engineering, and architectural aesthetics-related fields in the future.

  3. Effect of Junction Temperature Swing Durations on a Lifetime of a Transfer Molded IGBT Module

    DEFF Research Database (Denmark)

    Choi, Uimin; Blaabjerg, Frede; Jorgensen, Soren

    2016-01-01

    In this paper, the effect of junction temperature swing duration on the lifetime of a transfer molded Intelligent Power IGBT Module is studied and a relevant lifetime factor is modeled. A temperature swing duration dependent lifetime factor is defined based on 38 accelerated power cycling test...... results under 6 different conditions and it may improve a lifetime model for lifetime prediction of IGBT modules under various mission profiles of converters. The power cycling tests are performed by an advanced power cycling test setup which enables tested modules to be operated under more realistic...... electrical conditions during the power cycling test. The analysis of the test results and the temperature swing duration dependent lifetime factor under different definitions and confidence levels are presented....

  4. From Fantasy to Reality: A Grounded Theory of Experiences in the Swinging Lifestyle.

    Science.gov (United States)

    Kimberly, Claire; Hans, Jason D

    2017-04-01

    Swinger couples-committed couples who consensually engage in extra-relational sex for recreational purposes-are difficult for researchers to access due to the social stigma associated with swinging. This study builds upon the limited research on swinger couples by examining personal experiences with swinging. Specifically, 32 semi-structured interviews with swingers (16 husband-wife dyads, interviewed separately) were analyzed using grounded theory methods to understand the process of transitioning into and maintaining marital satisfaction in the swinging lifestyle. The model formed included (a) antecedent steps taken to enter into the lifestyle, (b) types of desires fulfilled, (c) stated benefits of being in the lifestyle, and (d) rules that guided couples throughout the process. Although variations were found across couples, the effective use of verbal and non-verbal communication to increase sexual and marital satisfaction within these non-monogamous couples was paramount to their experiences.

  5. Restricted Arm Swing Affects Gait Stability and Increased Walking Speed Alters Trunk Movements in Children with Cerebral Palsy

    Science.gov (United States)

    Delabastita, Tijs; Desloovere, Kaat; Meyns, Pieter

    2016-01-01

    Observational research suggests that in children with cerebral palsy, the altered arm swing is linked to instability during walking. Therefore, the current study investigates whether children with cerebral palsy use their arms more than typically developing children, to enhance gait stability. Evidence also suggests an influence of walking speed on gait stability. Moreover, previous research highlighted a link between walking speed and arm swing. Hence, the experiment aimed to explore differences between typically developing children and children with cerebral palsy taking into account the combined influence of restricting arm swing and increasing walking speed on gait stability. Spatiotemporal gait characteristics, trunk movement parameters and margins of stability were obtained using three dimensional gait analysis to assess gait stability of 26 children with cerebral palsy and 24 typically developing children. Four walking conditions were evaluated: (i) free arm swing and preferred walking speed; (ii) restricted arm swing and preferred walking speed; (iii) free arm swing and high walking speed; and (iv) restricted arm swing and high walking speed. Double support time and trunk acceleration variability increased more when arm swing was restricted in children with bilateral cerebral palsy compared to typically developing children and children with unilateral cerebral palsy. Trunk sway velocity increased more when walking speed was increased in children with unilateral cerebral palsy compared to children with bilateral cerebral palsy and typically developing children and in children with bilateral cerebral palsy compared to typically developing children. Trunk sway velocity increased more when both arm swing was restricted and walking speed was increased in children with bilateral cerebral palsy compared to typically developing children. It is proposed that facilitating arm swing during gait rehabilitation can improve gait stability and decrease trunk movements in

  6. Bridging the Gap

    DEFF Research Database (Denmark)

    Kramer Overgaard, Majken; Broeng, Jes; Jensen, Monika Luniewska

    Bridging the Gap (BtG) is a 2-year project funded by The Danish Industry Foundation. The goal of Bridging the Gap has been to create a new innovation model which will increase the rate at which Danish universities can spinout new technology ventures.......Bridging the Gap (BtG) is a 2-year project funded by The Danish Industry Foundation. The goal of Bridging the Gap has been to create a new innovation model which will increase the rate at which Danish universities can spinout new technology ventures....

  7. ENERGY-COST DURING AMBULATION IN TRANSFEMORAL AMPUTEES - A KNEE-JOINT WITH A MECHANICAL SWING PHASE-CONTROL VS A KNEE-JOINT WITH A PNEUMATIC SWING PHASE-CONTROL

    NARCIS (Netherlands)

    BOONSTRA, AM; SCHRAMA, J; FIDLER, [No Value; EISMA, WH

    The aim of the study was (i) to evaluate the preference of transfemoral amputees for a 4-bar linked knee joint with either a mechanical swing phase control or a pneumatic swing phase control, and (ii) to compare the energy expenditure in transfemoral amputees using a prosthesis with a mechanical

  8. Gasdynamic modeling and parametric study of mesoscale internal combustion swing engine/generator systems

    Science.gov (United States)

    Gu, Yongxian

    The demand of portable power generation systems for both domestic and military applications has driven the advances of mesoscale internal combustion engine systems. This dissertation was devoted to the gasdynamic modeling and parametric study of the mesoscale internal combustion swing engine/generator systems. First, the system-level thermodynamic modeling for the swing engine/generator systems has been developed. The system performance as well as the potentials of both two- and four-stroke swing engine systems has been investigated based on this model. Then through parameterc studies, the parameters that have significant impacts on the system performance have been identified, among which, the burn time and spark advance time are the critical factors related to combustion process. It is found that the shorter burn time leads to higher system efficiency and power output and the optimal spark advance time is about half of the burn time. Secondly, the turbulent combustion modeling based on levelset method (G-equation) has been implemented into the commercial software FLUENT. Thereafter, the turbulent flame propagation in a generic mesoscale combustion chamber and realistic swing engine chambers has been studied. It is found that, in mesoscale combustion engines, the burn time is dominated by the mean turbulent kinetic energy in the chamber. It is also shown that in a generic mesoscale combustion chamber, the burn time depends on the longest distance between the initial ignition kernel to its walls and by changing the ignition and injection locations, the burn time can be reduced by a factor of two. Furthermore, the studies of turbulent flame propagation in real swing engine chambers show that the combustion can be enhanced through in-chamber turbulence augmentation and with higher engine frequency, the burn time is shorter, which indicates that the in-chamber turbulence can be induced by the motion of moving components as well as the intake gas jet flow. The burn time

  9. Multi-Objective Motion Control Optimization for the Bridge Crane System

    Directory of Open Access Journals (Sweden)

    Renxin Xiao

    2018-03-01

    Full Text Available A novel control algorithm combining the linear quadratic regulator (LQR control and trajectory planning (TP is proposed for the control of an underactuated crane system, targeting position adjustment and swing suppression. The TP is employed to control the swing angle within certain constraints, and the LQR is applied to achieve anti-disturbance. In order to improve the accuracy of the position control, a differential-integral control loop is applied. The weighted LQR matrices representing priorities of the state variables for the bridge crane motion are searched by the multi-objective genetic algorithm (MOGA. The stability proof is provided in order to validate the effectiveness of the proposed algorithm. Numerous simulation and experimental validations justify the feasibility of the proposed method.

  10. Long-term bridge performance high priority bridge performance issues.

    Science.gov (United States)

    2014-10-01

    Bridge performance is a multifaceted issue involving performance of materials and protective systems, : performance of individual components of the bridge, and performance of the structural system as a whole. The : Long-Term Bridge Performance (LTBP)...

  11. Bridge health monitoring metrics : updating the bridge deficiency algorithm.

    Science.gov (United States)

    2009-10-01

    As part of its bridge management system, the Alabama Department of Transportation (ALDOT) must decide how best to spend its bridge replacement funds. In making these decisions, ALDOT managers currently use a deficiency algorithm to rank bridges that ...

  12. The Effect of Biological Movement Variability on the Performance of the Golf Swing in High- and Low-Handicapped Players

    Science.gov (United States)

    Bradshaw, Elizabeth J.; Keogh, Justin W. L.; Hume, Patria A.; Maulder, Peter S.; Nortje, Jacques; Marnewick, Michel

    2009-01-01

    The purpose of this study was to examine the role of neuromotor noise on golf swing performance in high- and low-handicap players. Selected two-dimensional kinematic measures of 20 male golfers (n = 10 per high- or low-handicap group) performing 10 golf swings with a 5-iron club was obtained through video analysis. Neuromotor noise was calculated…

  13. Load rating of complex bridges.

    Science.gov (United States)

    2010-07-01

    The National Bridge Inspection Standards require highway departments to inspect, evaluate, and determine load ratings for : structures defined as bridges located on all public roads. Load rating of bridges is performed to determine the live load that...

  14. Principles of Bridge Reliability

    DEFF Research Database (Denmark)

    Thoft-Christensen, Palle; Nowak, Andrzej S.

    The paper gives a brief introduction to the basic principles of structural reliability theory and its application to bridge engineering. Fundamental concepts like failure probability and reliability index are introduced. Ultimate as well as serviceability limit states for bridges are formulated...

  15. Covered Bridge Security Manual

    Science.gov (United States)

    Brett Phares; Terry Wipf; Ryan Sievers; Travis Hosteng

    2013-01-01

    The design, construction, and use of covered timber bridges is all but a lost art in these days of pre-stressed concrete, high-performance steel, and the significant growth both in the volume and size of vehicles. Furthermore, many of the existing covered timber bridges are preserved only because of their status on the National Registry of Historic Places or the...

  16. The floating water bridge

    International Nuclear Information System (INIS)

    Fuchs, Elmar C; Woisetschlaeger, Jakob; Gatterer, Karl; Maier, Eugen; Pecnik, Rene; Holler, Gert; Eisenkoelbl, Helmut

    2007-01-01

    When high voltage is applied to distilled water filled in two glass beakers which are in contact, a stable water connection forms spontaneously, giving the impression of a floating water bridge. A detailed experimental analysis reveals static and dynamic structures as well as heat and mass transfer through this bridge

  17. Active-bridge oscillator

    Science.gov (United States)

    Wessendorf, Kurt O.

    2001-01-01

    An active bridge oscillator is formed from a differential amplifier where positive feedback is a function of the impedance of one of the gain elements and a relatively low value common emitter resistance. This use of the nonlinear transistor parameter h stabilizes the output and eliminates the need for ALC circuits common to other bridge oscillators.

  18. Students design composite bridges

    NARCIS (Netherlands)

    Stark, J.W.B.; Galjaard, J.C.; Brekelmans, J.W.P.M.

    1999-01-01

    The paper gives an overview of recent research on steel-concrete composite bridge design by students of Delft University of Technology doing their master's thesis. Primary objective of this research was to find possibilities for application of steel-concrete composite bridges in the Netherlands,

  19. Virtual Bridge Design Challenge

    Science.gov (United States)

    Mitts, Charles R.

    2013-01-01

    This design/problem-solving activity challenges students to design a replacement bridge for one that has been designated as either structurally deficient or functionally obsolete. The Aycock MS Technology/STEM Magnet Program Virtual Bridge Design Challenge is an authentic introduction to the engineering design process. It is a socially relevant…

  20. Swing-leg trajectory of running guinea fowl suggests task-level priority of force regulation rather than disturbance rejection.

    Directory of Open Access Journals (Sweden)

    Yvonne Blum

    Full Text Available To achieve robust and stable legged locomotion in uneven terrain, animals must effectively coordinate limb swing and stance phases, which involve distinct yet coupled dynamics. Recent theoretical studies have highlighted the critical influence of swing-leg trajectory on stability, disturbance rejection, leg loading and economy of walking and running. Yet, simulations suggest that not all these factors can be simultaneously optimized. A potential trade-off arises between the optimal swing-leg trajectory for disturbance rejection (to maintain steady gait versus regulation of leg loading (for injury avoidance and economy. Here we investigate how running guinea fowl manage this potential trade-off by comparing experimental data to predictions of hypothesis-based simulations of running over a terrain drop perturbation. We use a simple model to predict swing-leg trajectory and running dynamics. In simulations, we generate optimized swing-leg trajectories based upon specific hypotheses for task-level control priorities. We optimized swing trajectories to achieve i constant peak force, ii constant axial impulse, or iii perfect disturbance rejection (steady gait in the stance following a terrain drop. We compare simulation predictions to experimental data on guinea fowl running over a visible step down. Swing and stance dynamics of running guinea fowl closely match simulations optimized to regulate leg loading (priorities i and ii, and do not match the simulations optimized for disturbance rejection (priority iii. The simulations reinforce previous findings that swing-leg trajectory targeting disturbance rejection demands large increases in stance leg force following a terrain drop. Guinea fowl negotiate a downward step using unsteady dynamics with forward acceleration, and recover to steady gait in subsequent steps. Our results suggest that guinea fowl use swing-leg trajectory consistent with priority for load regulation, and not for steadiness of gait

  1. Swing-Leg Trajectory of Running Guinea Fowl Suggests Task-Level Priority of Force Regulation Rather than Disturbance Rejection

    Science.gov (United States)

    Blum, Yvonne; Vejdani, Hamid R.; Birn-Jeffery, Aleksandra V.; Hubicki, Christian M.; Hurst, Jonathan W.; Daley, Monica A.

    2014-01-01

    To achieve robust and stable legged locomotion in uneven terrain, animals must effectively coordinate limb swing and stance phases, which involve distinct yet coupled dynamics. Recent theoretical studies have highlighted the critical influence of swing-leg trajectory on stability, disturbance rejection, leg loading and economy of walking and running. Yet, simulations suggest that not all these factors can be simultaneously optimized. A potential trade-off arises between the optimal swing-leg trajectory for disturbance rejection (to maintain steady gait) versus regulation of leg loading (for injury avoidance and economy). Here we investigate how running guinea fowl manage this potential trade-off by comparing experimental data to predictions of hypothesis-based simulations of running over a terrain drop perturbation. We use a simple model to predict swing-leg trajectory and running dynamics. In simulations, we generate optimized swing-leg trajectories based upon specific hypotheses for task-level control priorities. We optimized swing trajectories to achieve i) constant peak force, ii) constant axial impulse, or iii) perfect disturbance rejection (steady gait) in the stance following a terrain drop. We compare simulation predictions to experimental data on guinea fowl running over a visible step down. Swing and stance dynamics of running guinea fowl closely match simulations optimized to regulate leg loading (priorities i and ii), and do not match the simulations optimized for disturbance rejection (priority iii). The simulations reinforce previous findings that swing-leg trajectory targeting disturbance rejection demands large increases in stance leg force following a terrain drop. Guinea fowl negotiate a downward step using unsteady dynamics with forward acceleration, and recover to steady gait in subsequent steps. Our results suggest that guinea fowl use swing-leg trajectory consistent with priority for load regulation, and not for steadiness of gait. Swing

  2. A comparison of the modern and classic golf swing: a clinician's ...

    African Journals Online (AJOL)

    . The clubhead hits the ball. Early follow-through. From impact to club horizontal to ground. Late follow-through. From club horizontal to end of swing. Results in the ... tus lateralis and adductor magnus.4,32 In the upper body, the combined ...

  3. Designing Playful Interactive Installations for Urban Environments - The SwingScape Experience

    DEFF Research Database (Denmark)

    Grønbæk, Kaj; Kortbek, Karen Johanne; Christensen, Claus Møller

    2012-01-01

    . The design issues include: creating playful and collective interaction, making a familiar swing interaction simulate the experience of a music mixing board, providing gentle integration of multimedia (light and sound) in the atmosphere of an urban space, and finally making installations robust and safe...

  4. Honey bees (Apis mellifera ligustica) swing abdomen to dissipate residual flying energy landing on a wall

    Science.gov (United States)

    Zhao, Jieliang; Huang, He; Yan, Shaoze

    2017-03-01

    Whether for insects or for aircrafts, landing is one of the indispensable links in the verification of airworthiness safety. The mechanisms by which insects achieve a fast and stable landing remain unclear. An intriguing example is provided by honeybees (Apis mellifera ligustica), which use the swinging motion of their abdomen to dissipate residual flying energy and to achieve a smooth, stable, and quick landing. By using a high-speed camera, we observed that touchdown is initiated by honeybees extending their front legs or antennae and then landing softly on a wall. After touchdown, they swing the rest of their bodies until all flying energy is dissipated. We suggested a simplified model with mass-spring dampers for the body of the honeybee and revealed the mechanism of flying energy transfer and dissipation in detail. Results demonstrate that body translation and abdomen swinging help honeybees dissipate residual flying energy and orchestrate smooth landings. The initial kinetic energy of flying is transformed into the kinetic energy of the abdomen's rotary movement. Then, the kinetic energy of rotary movement is converted into thermal energy during the swinging cycle. This strategy provides more insight into the mechanism of insect flying, which further inspires better design on aerial vehicle with better landing performance.

  5. Study on Effect of Junction Temperature Swing Duration on Lifetime of Transfer Molded Power IGBT Modules

    DEFF Research Database (Denmark)

    Choi, Uimin; Blaabjerg, Frede; Jørgensen, Søren

    2017-01-01

    In this paper, the effect of junction temperature swing duration on lifetime of transfer molded power insulated gate bipolar transistor (IGBT) modules is studied and a relevant lifetime factor is modeled. This study is based on 39 accelerated power cycling test results under six different...

  6. Electromyographic analysis of lower limb muscles during the golf swing performed with three different clubs.

    Science.gov (United States)

    Marta, Sérgio; Silva, Luís; Vaz, João Rocha; Castro, Maria António; Reinaldo, Gustavo; Pezarat-Correia, Pedro

    2016-01-01

    The aim of this study was to describe and compare the EMG patterns of select lower limb muscles throughout the golf swing, performed with three different clubs, in non-elite middle-aged players. Fourteen golfers performed eight swings each using, in random order, a pitching wedge, 7-iron and 4-iron. Surface electromyography (EMG) was recorded bilaterally from lower limb muscles: tibialis anterior, peroneus longus, gastrocnemius medialis, gastrocnemius lateralis, biceps femoris, semitendinosus, gluteus maximus, vastus medialis, rectus femoris and vastus lateralis. Three-dimensional high-speed video analysis was used to determine the golf swing phases. Results showed that, in average handicap golfers, the highest muscle activation levels occurred during the Forward Swing Phase, with the right semitendinosus and the right biceps femoris muscles producing the highest mean activation levels relative to maximal electromyography (70-76% and 68-73% EMG(MAX), respectively). Significant differences between the pitching wedge and the 4-iron club were found in the activation level of the left semitendinosus, right tibialis anterior, right peroneus longus, right vastus medialis, right rectus femuris and right gastrocnemius muscles. The lower limb muscles showed, in most cases and phases, higher mean values of activation on electromyography when golfers performed shots with a 4-iron club.

  7. Jazz Style and Articulation: How to Get Your Band or Choir to Swing

    Science.gov (United States)

    Tolson, Jerry

    2012-01-01

    The interpretation of jazz style is crucial to the element of swing in any jazz ensemble performance. Today, many charts for both large and small instrumental and vocal jazz ensembles are well marked with articulations and expression markings. However, in some cases, there is nothing to guide the musician. This article addresses some common jazz…

  8. Research on the measurement technology of effective arm length of swing arm profilometer

    Science.gov (United States)

    Chen, Lin; Jing, Hongwei; Wei, Zhongwei; Li, Jie; Cao, Xuedong

    2014-09-01

    When the swing arm profilometer(SAP) measuring the mirror, the effective arm length of SAP which haves an obvious influence on the measurement results of the mirror surface shape needs to be measured accurately. It requires the measurement uncertainty of the effective arm length to reach 10μm in order to meet the measurement requirements, in this paper, we present a kind of technology based on laser tracker to measure the effective arm length of SAP. When the swing arm rotates around the shaft axis of swing arm rotary stage, the probe and two laser tracker balls form three sections of circular arc around the shaft axis of swing arm rotary stage in space. Laser tracker tracks and measures the circular arcs of two laser tracker balls, the center coordinates of the circular plane of circular arc can be calculated by data processing. The linear equation that passes through the two center coordinates is the equation of the shaft axis of rotary stage, the vertical distance from the probe to the shaft axis of rotary stage which can be calculated refer to the equation from the point to the line is the effective arm length. After Matlab simulation, this measurement method can meet the measurement accuracy.

  9. Cardiovascular and Metabolic Demads of the Kettlebell Swing using Tabata Interval versus a Traditional Resistance Protocol

    Science.gov (United States)

    FORTNER, HOWARD A.; SALGADO, JEANETTE M.; HOLMSTRUP, ANGELICA M.; HOLMSTRUP, MICHAEL E.

    2014-01-01

    Tabata (TAB) training, consisting of eight cycles of 20 seconds of maximal exercise followed by 10 seconds of rest, is time-efficient, with aerobic and anaerobic benefit. This study investigated the cardiovascular and metabolic demands of a TAB versus traditional (TRAD) resistance protocol with the kettlebell swing. Fourteen young (18–25y), non-obese (BMI 25.7±0.8 kg/m2) participants reported on three occasions. All testing incorporated measurements of HR, oxygen consumption, and blood lactate accumulation. Each participant completed Tabata kettlebell swings (male- 8kg, female- 4.5kg; 8 intervals; 20s maximal repetitions, 10s rest). On a subsequent visit (TRAD), the total swings from the TAB protocol were evenly divided into 4 sets, with 90s rest between sets. Outcome measures were compared using paired t-tests. The TAB was completed more quickly than the TRAD protocol (240.0±0.0 v. 521.5±3.3 sec, PTRAD framework. Appropriate screening and risk stratification are advised before implementing kettlebell swings. PMID:27182402

  10. An efficient pricing algorithm for swing options based on Fourier cosine expansions

    NARCIS (Netherlands)

    Zhang, B.; Oosterlee, C.W.

    2013-01-01

    Swing options give contract holders the right to modify amounts of future delivery of certain commodities, such as electricity or gas. We assume that these options can be exercised at any time before the end of the contract, and more than once. However, a recovery time between any two consecutive

  11. Neuro fuzzy control of the FES assisted freely swinging leg of paraplegic subjects

    NARCIS (Netherlands)

    van der Spek, J.H.; Velthuis, W.J.R.; Veltink, Petrus H.; de Vries, Theodorus J.A.

    1996-01-01

    The authors designed a neuro fuzzy control strategy for control of cyclical leg movements of paraplegic subjects. The cyclical leg movements were specified by three `swing phase objectives', characteristic of natural human gait. The neuro fuzzy controller is a combination of a fuzzy logic controller

  12. Effect of arm swing strategy on local dynamic stability of human gait

    NARCIS (Netherlands)

    Punt, M.; Bruijn, S.M.; Wittink, H.; van Dieen, J.H.

    2015-01-01

    Introduction: Falling causes long term disability and can even lead to death. Most falls occur during gait. Therefore improving gait stability might be beneficial for people at risk of falling. Recently arm swing has been shown to influence gait stability. However at present it remains unknown which

  13. High Bar Swing Performance in Novice Adults: Effects of Practice and Talent

    Science.gov (United States)

    Busquets, Albert; Marina, Michel; Irurtia, Alfredo; Ranz, Daniel; Angulo-Barroso, Rosa M.

    2011-01-01

    An individual's a priori talent can affect movement performance during learning. Also, task requirements and motor-perceptual factors are critical to the learning process. This study describes changes in high bar swing performance after a 2-month practice period. Twenty-five novice participants were divided by a priori talent level…

  14. Rational design of temperature swing adsorption cycles for post-combustion CO2 capture

    NARCIS (Netherlands)

    Joss, Lisa; Gazzani, Matteo; Mazzotti, Marco

    2017-01-01

    The design of temperature swing adsorption (TSA) cycles aimed at recovering the heavy product at high purity is investigated by model-based design and applied to the capture of CO2 from flue gases. This model based design strategy and an extensive parametric analysis enables gaining an understanding

  15. A Datalogger Demonstration of Electromagnetic Induction with a Falling, Oscillating and Swinging Magnet

    Science.gov (United States)

    Wong, Darren; Lee, Paul; Foong, See Kit

    2010-01-01

    We investigate the electromagnetic induction phenomenon for a "falling," "oscillating" and "swinging" magnet and a coil, with the help of a datalogger. For each situation, we discuss the salient aspects of the phenomenon, with the aid of diagrams, and relate the motion of the magnet to its mathematical and graphical representations. Using various…

  16. Comparison of kettlebell swings and treadmill running at equivalent rating of perceived exertion values.

    Science.gov (United States)

    Hulsey, Caleb R; Soto, David T; Koch, Alexander J; Mayhew, Jerry L

    2012-05-01

    The purpose of this study was to compare metabolic demand of a kettlebell (KB) swing routine with treadmill (TM) running at equivalent rating of perceived exertion (RPE). Thirteen subjects (11 male, 2 female, age = 21.4 ± 2.1 years, weight = 73.0 ± 9.2 kg) completed a 10-minute KB swing routine consisting of 35-second swing intervals followed by 25-second rest intervals. Men used a 16-kg KB, and women used an 8-kg KB. After 48 hours of rest, the subjects completed a 10-minute TM run at equivalent RPEs as measured during the swing workout. Metabolic data were monitored each minute during each exercise using an automated cart, with the final 7 minutes used for analysis. The RPE and heart rate (HR) recorded at minutes 5, 7, 9, and 10 increased by 2-3 and 7-9%, respectively, for each exercise, producing a significantly increasing pattern but no significant difference between exercises. Average HR and RPE were not significantly different between KB and TM and averaged 90 and 89%, respectively, of age-predicted HRmax. Oxygen consumption, METS, pulmonary ventilation, and calorie expenditure were significantly higher for TM (25-39%) than for KB. Respiratory exchange ratio (TM = 0.94 ± 0.04, KB = 0.95 ± 0.05) and respiratory rate (TM = 38 ± 7, KB = 36 ± 4 b·min) were not significantly different between the exercises at any time point. During TM and KB exercises matched for RPE, the subjects are likely to have higher oxygen consumption, work at a higher MET level, and burn more kilocalories per minute during TM running than during KB swings. However, according to the American College of Sports Medicine standards, this KB drill could provide sufficient exercise stress to produce gains in aerobic capacity.

  17. Sustainable Bridge Infrastructure Procurement

    DEFF Research Database (Denmark)

    Safi, Mohammed; Du, Guangli; Simonsson, Peter

    2016-01-01

    The lack of a flexible but systematic approach for integrating lifecycle aspects into bridge investment decisions is a major obstacle hindering the procurement of sustainable bridge infrastructures. This paper addresses this obstacle by introducing a holistic approach that agencies could use to p...... to procure the most “sustainable” (lifecycle-efficient) bridge through a fair design-build (D-B) tendering process, considering all the main aspects: life-cycle cost (LCC), service life-span, aesthetic demands and environmental impacts (LCA)....

  18. Bridge technology report

    CERN Document Server

    2013-01-01

    Please note this is a Short Discount publication. As LANs have proliferated, new technologies and system concepts have come to the fore. One of the key issues is how to interconnect networks. One means of interconnection is to use a 'bridge'. Other competing technologies are repeaters, routers, and gateways. Bridges permit traffic isolation, connect network segments together and operate at the MAC layer. Further, because they operate at the MAC layer, they can handle a variety of protocols such as TCP/IP, SNA, and X.25. This report focuses on the specific technology of bridging two netw

  19. Bridging Humanism and Behaviorism.

    Science.gov (United States)

    Chu, Lily

    1980-01-01

    Humanistic behaviorism may provide the necessary bridge between behaviorism and humanism. Perhaps the most humanistic approach to teaching is to learn how certain changes will help students and how these changes can be accomplished. (Author/MLF)

  20. Skewed highway bridges.

    Science.gov (United States)

    2013-07-01

    Many highway bridges are skewed and their behavior and corresponding design analysis need to be furthered to fully accomplish design objectives. This project used physical-test and detailed finite element analysis to better understand the behavior of...

  1. Bridge removal plan requirements.

    Science.gov (United States)

    2011-04-15

    This report provides resources that detail specifications and guidelines related to bridge removal plans across the : United States. We have organized the information into three sections: : ! National Guidance : Includes language from AASHTO specific...

  2. Forward Affect Bridge.

    Science.gov (United States)

    Bonshtein, Udi; Torem, Moshe

    2017-01-01

    This article presents a modification of the affect bridge technique. The Forward Affect Bridge enables practitioners to create and maintain hope when it is missing. Hope is relevant for diminishing avoidance and being involved with necessary activities. The main idea is to build up a positive atmosphere in the here and now (relying on rapport), to amplify it, and to project it forward. By using clinical vignettes, the authors illustrate these techniques.

  3. Transfemoral amputee recovery strategies following trips to their sound and prosthesis sides throughout swing phase.

    Science.gov (United States)

    Shirota, Camila; Simon, Ann M; Kuiken, Todd A

    2015-09-09

    Recovering from trips is challenging for transfemoral amputees, and attempts often result in falls. Better understanding of the effects of the sensory-motor deficits brought by amputation and the functional limitations of prosthetic devices could help guide therapy and fall prevention mechanisms in prostheses. However, how transfemoral amputees attempt to recover from trips on the sound and prosthesis sides throughout swing phase is poorly understood. We tripped eight able-bodied subjects and eight unilateral transfemoral amputees wearing their prescribed prostheses. The protocol consisted of six repetitions of 6 and 4 points throughout swing phase, respectively. We compared recovery strategies in able-bodied, sound side and prosthesis side limbs. The number of kinematic recovery strategies used, when they were used throughout swing phase, and kinematic characteristics (tripped limb joint angles, bilateral trochanter height and time from foot arrest to foot strike) of each strategy were compared across limb groups. Non-parametric statistical tests with corrections for post-hoc tests were used. Amputees used the same recovery strategies as able-bodied subjects on both sound and prosthesis sides, although not all subjects used all strategies. Compared to able-bodied subjects, amputees used delayed-lowering strategies less often from 30-60 % of swing phase on the sound side, and from 45-60 % of swing phase on the prosthesis side. Within-strategy kinematic differences occurred across limbs; however, these differences were not consistent across all strategies. Amputee-specific recovery strategies-that are not used by control subjects-occurred following trips on both the sound and prosthesis sides in mid- to late swing. Collectively, these results suggest that sensory input from the distal tripped leg is not necessary to trigger able-bodied trip recovery strategies. In addition, the differences between sound and prosthesis side recoveries indicate that the ability of the

  4. Long Span Bridges in Scandinavia

    DEFF Research Database (Denmark)

    Gimsing, Niels Jørgen

    1998-01-01

    The first Scandinavian bridge with a span of more than 500 m was the Lillebælt Suspension Bridge opened to traffic in 1970.Art the end of the 20th century the longest span of any European bridge is found in the Storebælt East Bridge with a main span of 1624 m. Also the third longest span in Europe...... is found in Scandinavia - the 1210 m span of the Höga Kusten Bridge in Sweden.The Kvarnsund Bridge in Norway was at the completion in 1991 the longest cable-stayed bridge in the world, and the span of 530 m is still thge longest for cable-stayed bridges in concrete. The Øresund Bridge with its sapn of 490...... m is the longest among cable-stayed bridges for both road and railway traffic....

  5. Cooperativity of complex salt bridges

    OpenAIRE

    Gvritishvili, Anzor G.; Gribenko, Alexey V.; Makhatadze, George I.

    2008-01-01

    The energetic contribution of complex salt bridges, in which one charged residue (anchor residue) forms salt bridges with two or more residues simultaneously, has been suggested to have importance for protein stability. Detailed analysis of the net energetics of complex salt bridge formation using double- and triple-mutant cycle analysis revealed conflicting results. In two cases, it was shown that complex salt bridge formation is cooperative, i.e., the net strength of the complex salt bridge...

  6. Structural assessment of concrete bridges

    OpenAIRE

    Plos, Mario; Gylltoft, Kent; Lundgren, Karin; Cervenka, Jan; Herwig, Andrin; Brühwiler, Eugen; Thelandersson, Sven; Elfgren, Lennart; Rosell, Ebbe

    2008-01-01

    The paper summarizes the work on concrete bridges performed in the EU project Sustainable Bridges. The work provides enhanced assessment methods that are able to provide higher load-carrying capacities and longer fatigue lives for exixixting concrete railway bridges. The work is also presented in a Guideleine available at http://www.sustainablebridges.net/ The paper summarizes the work on concrete bridges performed in the EU project Sustainable Bridges. The work provides enhanced assessmen...

  7. Swinging multi-source industrial CT systems for aperiodic dynamic imaging.

    Science.gov (United States)

    Wu, Weiwen; Yu, Hengyong; Gong, Changcheng; Liu, Fenglin

    2017-10-02

    The goal of this paper is to develop a new architecture for industrial computed tomography (ICT) aiming at dynamically imaging an aperiodic changing object. We propose a data acquisition approach with multiple x-ray source/detector pairs targeting a continuously changeable object with corresponding timeframes. In this named swinging multi-source CT (SMCT) structure, each source and its associated detector swing forth and back within a certain angle for CT scanning. In the SMCT system design, we utilize a circular journal bearing based setup to replace the normal CT slip ring by weakening the scanning speed requirement. Inspired by the prior image constrained compressed sensing (PICCS) algorithm, we apply a modified PICCS algorithm for the SMCT (SM-PICCS). Our numerical simulation and realistic specimen experiment studies demonstrate the feasibility of the proposed approach.

  8. Fast generation shedding equipment based on the observation of swings of generators

    International Nuclear Information System (INIS)

    Takahashi, M.; Matsuzawa, K.; Sato, M.; Omata, K.; Tsukui, R.; Nakamura, T.; Mizuguchi, S.

    1988-01-01

    This paper presents a new method and newly developed stabilizing equipment to prevent the loss of synchronism of generators in pumped-storage plants from spreading. The proposed method includes functions to estimate the swing of each generator by using on-line generator output sampled at a rate of 600 times per second after an occurrence of disturbance such as fault, faulty equipment and so on, to predict generator swing 200-300 milliseconds ahead and loss of synchronism between generators in pumped-storage plants and those in thermal and nuclear plants, and to decide the number of generators that must be shed to maintain stability. Tokyo Electric Power Co. (TEPCO) installed the newly developed stabilizing equipment based on this method in the power system in June, 1986

  9. Maxillary Swing Approach for Removal of Palatal Carcinoma: A Modified Procedure

    Directory of Open Access Journals (Sweden)

    Tsutomu Nomura

    2018-01-01

    Full Text Available Introduction. We report a modification of the maxillary swing approach to remove a palatal tumor while preserving the anterior alveolar area. Methods. Case report using clinical records. Results. The patient was a 54-year-old male. TNM grade was T4bN0M0, and invasion to the base of the pterygoid process was seen. Two courses of induction chemotherapy were administered prior to the operation. Because there was no evidence of anterior maxillary invasion, the maxillary swing approach was chosen. The left anterior maxilla was cut and swung laterally, preserving the blood supply. After removal of the palatal tumor, the maxilla was repositioned and the defect was restored with an anterior lateral thigh flap. Postoperative course was typical, and facial appearance, speech, and masticatory function were satisfactory. Conclusions. This technique is particularly useful for preserving appearance as well as speech and mastication.

  10. PKU: high plasma phenylalanine concentrations are associated with increased prevalence of mood swings.

    Science.gov (United States)

    Anjema, Karen; van Rijn, Margreet; Verkerk, Paul H; Burgerhof, Johannes G M; Heiner-Fokkema, M Rebecca; van Spronsen, Francjan J

    2011-11-01

    In phenylketonuria, knowledge about the relation between behavior and plasma phenylalanine is scarce. The aim of this study was to determine whether high phenylalanine is associated with disturbed behavior noticed by the patient and or close environment (parents or partners). 48 early treated PKU patients (median age 8.5, range 0-35 years) participated (median phenylalanine concentration in total sample 277 (range 89-1171) μmol/l; and in patients introvert or extravert behavior. The interviewer as well as the respondents were blinded with regard to the phenylalanine concentration. Patients reported less deviant behavior compared to close environment. Mood swings were positively associated with phenylalanine concentrations in the total group (P=0.039) and patients introvert and extravert behavior were not statistically significant. there is a positive association between phenylalanine concentrations and mood swings. Copyright © 2011 Elsevier Inc. All rights reserved.

  11. Treatment of uncertainty through the interval smart/swing weighting method: a case study

    Directory of Open Access Journals (Sweden)

    Luiz Flávio Autran Monteiro Gomes

    2011-12-01

    Full Text Available An increasingly competitive market means that many decisions must be taken, quickly and with precision, in complex, high risk scenarios. This combination of factors makes it necessary to use decision aiding methods which provide a means of dealing with uncertainty in the judgement of the alternatives. This work presents the use of the MAUT method, combined with the INTERVAL SMART/SWING WEIGHTING method. Although multicriteria decision aiding was not conceived specifically for tackling uncertainty, the combined use of MAUT and the INTERVAL SMART/SWING WEIGHTING method allows approaching decision problems under uncertainty. The main concepts which are involved in these two methods are described and their joint application to the case study concerning the selection of a printing service supplier is presented. The case study makes use of the WINPRE software as a support tool for the calculation of dominance. It is then concluded that the proposed approach can be applied to decision making problems under uncertainty.

  12. Validation of an Inertial Sensor System for Swing Analysis in Golf

    Directory of Open Access Journals (Sweden)

    Paul Lückemann

    2018-02-01

    Full Text Available Wearable inertial sensor systems are an upcoming tool for self-evaluation in sports, and can be used for swing analysis in golf. The aim of this work was to determine the validity and repeatability of an inertial sensor system attached to a player’s glove using a radar system as a reference. 20 subjects performed five full swings with each of three different clubs (wood, 7-iron, wedge. Clubhead speed was measured simultaneously by both sensor systems. Limits of Agreement were used to determine the accuracy and precision of the inertial sensor system. Results show that the inertial sensor system is quite accurate but with a lack of precision. Random error was quantified to approximately 17 km/h. The measurement error was dependent on the club type and was weakly negatively correlated to the magnitude of clubhead speed.

  13. Creative mood swings: divergent and convergent thinking affect mood in opposite ways.

    Science.gov (United States)

    Akbari Chermahini, Soghra; Hommel, Bernhard

    2012-09-01

    Increasing evidence suggests that emotions affect cognitive processes. Recent approaches have also considered the opposite: that cognitive processes might affect people's mood. Here we show that performing and, to a lesser degree, preparing for a creative thinking task induce systematic mood swings: Divergent thinking led to a more positive mood, whereas convergent thinking had the opposite effect. This pattern suggests that thought processes and mood are systematically related but the type of relationship is process-specific.

  14. An Ingenious Modification in Conventional Swing Lock Cast Partial Denture for Rehabilitating A Hemi Mandibulectomy Defect.

    Science.gov (United States)

    Shah, Rupal Jaydip; Lagdive, Sanjay Balaji; Saini, Shraddha Lalit; Verma, Vishal Bipinbihari; Shah, Satyaprakash Ranjit

    2017-01-01

    Mandibular resections compromise the balance and symmetry of mandibular functions. Since centuries there has been advent of various prosthetic treatment modalities to improve the masticatory efficiency. Swing lock dentures, a treatment facet with high degree of clinical effectiveness, yet gradually fading into oblivion due to its design complexities, has been resurrected by retaining its indigenous concept of reciprocation, and consolidating aesthetics with introduction of newer breed of aesthetic material (Thermoplastic Acetal resin).

  15. Effects of Kettlebell Swing vs. Explosive Deadlift Training on Strength and Power

    Directory of Open Access Journals (Sweden)

    Matthew R. Maulit

    2017-01-01

    Full Text Available Background: Recent research has compared explosive deadlift to kettlebell training observing their effects on strength. The kettlebell swing is a popular practical exercise as it shares share a hip hinge movement with the explosive deadlift, but the two have not been compared. Objectives: The purpose of this study was to compare the effects of kettlebell swing vs. explosive deadlift training on strength and power. Methods: Thirty-one recreationally resistance-trained men (age = 23.1 ± 2.3 years, height = 175.5 ± 6.6 cm, mass = 83.9 ± 13.8 kg, 1RM deadlift = 159.9 ± 31.7 kg were randomly assigned to one of two groups [kettlebell swing group (KBG n = 15, or explosive deadlift group (EDLG n = 16]. Vertical jump height, isometric mid-thigh pull (MTP, and 1RM deadlift were measured pre and post training. Both groups trained twice per week for 4 weeks. Volume and load were increased after the first 2 weeks of training. Results: A 2 (time x 2 (group mixed factor ANOVA revealed a significant (P<0.05 increase in deadlift 1RM (pre: 159.9 ± 31.7 kg, post: 168.9 ± 31.8 kg and vertical jump height (pre: 56.6 ± 9.9 cm, post: 57.9 ± 9.7 cm for both groups, but were not significantly different between groups. There were no significant changes in MTP. Conclusions: Strength and conditioning professionals may use both kettlebell swings and explosive deadlifts to increase deadlift strength and vertical jump power.

  16. Creative mood swings: divergent and convergent thinking affect mood in opposite ways

    OpenAIRE

    Akbari Chermahini, Soghra; Hommel, Bernhard

    2011-01-01

    Increasing evidence suggests that emotions affect cognitive processes. Recent approaches have also considered the opposite: that cognitive processes might affect people’s mood. Here we show that performing and, to a lesser degree, preparing for a creative thinking task induce systematic mood swings: Divergent thinking led to a more positive mood, whereas convergent thinking had the opposite effect. This pattern suggests that thought processes and mood are systematically related but the type o...

  17. Comparison between swinging and playing of white noise among colicky babies: A paired randomised controlled trial.

    Science.gov (United States)

    Sezici, Emel; Yigit, Deniz

    2018-02-01

    This study aimed to compare the effects of swinging and playing of white noise on the crying and sleeping durations of colicky babies. Infantile colic (IC) is one of the most common reasons for doctor visits among babies younger than 3 months. One of five babies older than 3 months also experiences IC. IC, unlike gastrointestinal problems, is regarded as an individual differentiation and maturation of the central nervous system. Providing a warm bath, breastfeeding, swinging and playing of white noise are nonpharmacological methods. The efficiency of these methods has been proven by various studies independently of one another. The study is a prospective, multicentre, paired randomised controlled trial. The study was conducted between April-December 2016. The study sample consisted of 40 1-month-old babies with gas pains who passed a hearing screening and their mothers. The total daily crying and sleeping durations of the babies were determined without any intervention on the first week. On the second week, 20 randomly selected babies (first group) were swung each time they cried, and on the third week, they were made to listen to white noise. The other 20 babies (second group) were made to listen to white noise on the second week and were swung on the third week. Swinging and playing of white noise were performed until the babies stopped crying. After every intervention, the total crying and sleeping durations of the babies were evaluated using a "Colicky Baby's Diary." Playing of white noise significantly decreased the daily crying durations (p white noise was found to be a more effective nonpharmacological method on crying and sleeping durations of colicky babies than swinging. Playing of white noise may be helpful for parents and healthcare personnel in reducing the gas pains of babies. © 2017 John Wiley & Sons Ltd.

  18. Explaining medium run swings in unemployment : shocks, monetary policy and labour market frictions

    OpenAIRE

    Rannenberg, Ansgar

    2010-01-01

    The literature trying to link the increase in unemployment in many western European countries since the middle of the 1970s to an increase in labour market rigidity has run into a number of problems. In particular, changes in labour market institutions do not seem to be able to explain the evolution of unemployment across time. We conclude that a new theory of medium run unemployment swings should explain the increase in unemployment in many European countries and the lack thereof...

  19. Enhanced arm swing alters interlimb coordination during overground walking in individuals with traumatic brain injury.

    Science.gov (United States)

    Ustinova, Ksenia I; Langenderfer, Joseph E; Balendra, Nilanthy

    2017-04-01

    The current study investigated interlimb coordination in individuals with traumatic brain injury (TBI) during overground walking. The study involved 10 participants with coordination, balance, and gait abnormalities post-TBI, as well as 10 sex- and age-matched healthy control individuals. Participants walked 12m under two experimental conditions: 1) at self-selected comfortable walking speeds; and 2) with instructions to increase the amplitude and out-of-phase coordination of arm swinging. The gait was assessed with a set of spatiotemporal and kinematic parameters including the gait velocity, step length and width, double support time, lateral displacement of the center of mass, the amplitude of horizontal trunk rotation, and angular motions at shoulder and hip joints in sagittal plane. Interlimb coordination (coupling) was analyzed as the relative phase angles between the left and right shoulders, hips, and contralateral shoulders and hips, with an ideal out-of-phase coupling of 180° and ideal in-phase coupling of 0°. The TBI group showed much less interlimb coupling of the above pairs of joint motions than the control group. When participants were required to increase and synchronize arm swinging, coupling between shoulder and hip motions was significantly improved in both groups. Enhanced arm swinging was associated with greater hip and shoulder motion amplitudes, and greater step length. No other significant changes in spatiotemporal or kinematic gait characteristics were found in either group. The results suggest that arm swinging may be a gait parameter that, if controlled properly, can improve interlimb coordination during overground walking in patients with TBI. Copyright © 2017 Elsevier B.V. All rights reserved.

  20. Brain blood-flow changes during motion sickness. [thalamus vascular changes in dogs during swing tests

    Science.gov (United States)

    Johnson, W. H.; Hsuen, J.

    1973-01-01

    The possibility of diminished blood flow in the brain is studied as one of the factors resulting from an increase in skeletal muscle blood volume concomitant with other characteristics of motion sickness. Thermistors are implanted in the thalamus of dogs and blood flow changes are recorded while they are subjected to sinusoidal movement on a two pole swing. Results of these initial steps in a proposed long term exploration of different areas of the brain are presented.

  1. Experiments on the Porch Swing Bearing of Michelson Interferometer for Low Resolution FTIR

    OpenAIRE

    Tuomas Välikylä; Jyrki Kauppinen

    2013-01-01

    Porch swing bearing for the linear motion of the mirror in Michelson interferometer for mid-infrared low resolution Fourier transform spectrometer was studied experimentally using the modulation depth of the collimated laser beam. The mirror tilting was measured to be lower than 5 μrad over 3 mm mirror travel using two different bearings assemblies. Additionally, the manufacturing tolerances of the bearing type were proved to be loose enough not to limit the interferometer application. These ...

  2. Foot varus in stroke patients: muscular activity of extensor digitorum longus during the swing phase of gait.

    Science.gov (United States)

    Reynard, F; Dériaz, O; Bergeau, J

    2009-06-01

    Hemiparetic patients often present an abnormal leg muscles balance that can lead to foot deformities like equinovarus or varus. To assess whether a muscle imbalance between tibialis anterior and extensor digitorum longus was associated with a varus deformity of the foot during the swing phase of gait in stroke patients. Twenty hemiparetic patients presenting a foot varus during the swing phase of gait were compared to 16 healthy subjects. Gait was analyzed by video recording and by surface electromyography. Duration and magnitude of electromyographic signal were collected for tibialis anterior and extensor digitorum longus. Presence of an activity of the calf muscles during the swing phase was also evaluated. Hemiparetic patients exhibited more often premature activity of the calf muscles (pextensor digitorum longus (pextensor digitorum longus activity (pextensor digitorum longus muscle during the swing phase of gait is important to balance the foot in the frontal plane. The activation of that muscle should be included in rehabilitation programs.

  3. Warm-up with weighted bat and adjustment of upper limb muscle activity in bat swinging under movement correction conditions.

    Science.gov (United States)

    Ohta, Yoichi; Ishii, Yasumitsu; Ikudome, Sachi; Nakamoto, Hiroki

    2014-02-01

    The effects of weighted bat warm-up on adjustment of upper limb muscle activity were investigated during baseball bat swinging under dynamic conditions that require a spatial and temporal adjustment of the swinging to hit a moving target. Seven male college baseball players participated in this study. Using a batting simulator, the task was to swing the standard bat coincident with the arrival timing and position of a moving target after three warm-up swings using a standard or weighted bat. There was no significant effect of weighted bat warm-up on muscle activity before impact associated with temporal or spatial movement corrections. However, lower inhibition of the extensor carpi ulnaris muscle activity was observed in a velocity-changed condition in the weighted bat warm-up, as compared to a standard bat warm-up. It is suggested that weighted bat warm-up decreases the adjustment ability associated with inhibition of muscle activation under movement correction conditions.

  4. Investigations of leakage mechanisms and its influences on a micro swing engine considering rarefaction effects

    International Nuclear Information System (INIS)

    Zhou, Xiong; Zhang, Zhenyu; Kong, Wenjun; Du, Ning

    2016-01-01

    Highlights: • Mechanisms of the leakage flow in different flow regimes have been studied. • The leakage flow regime and patterns in the micro swing engine are presented. • Slip on the walls has a larger effect on leakage flow with decreasing the gap. • Rarefaction effects on the engine performance have been investigated. - Abstract: Considering rarefaction effects, this paper investigated mechanisms of the clearance leakage and its influences on a micro swing engine for the micro power generation by employing three different flow models named as discrete velocity direction (DVD) model, Navier-Stokes equations with slip boundary conditions (NS-slip) and no-slip boundary conditions (NS-no slip). Using the DVD model, this paper firstly studied leakage mechanisms of a micro Couette-Poisueille flow. Factors which control the leakage in different regimes were obtained. Furthermore, the system-level predictions of the clearance leakage in the micro swing engine have been conducted by solving the Navier-Stokes equations. The leakage flow regime, patterns and characteristics were presented. Results by NS-slip and NS-no slip were compared to study the rarefaction effects. Finally, investigations of the engine size and the gap height on the engine performance have been conducted. The significance of the leakage in different engine size regimes was presented, and the results show that rarefaction effects affect the indicated thermal efficiency greatly with the decrease of the engine size scale.

  5. Simulation of Pressure-swing Distillation for Separation of Ethyl Acetate-Ethanol-Water

    Science.gov (United States)

    Yang, Jing; Zhou, Menglin; Wang, Yujie; Zhang, Xi; Wu, Gang

    2017-12-01

    In the light of the azeotrope of ethyl acetate-ethanol-water, a process of pressure-swing distillation is proposed. The separation process is simulated by Aspen Plus, and the effects of theoretical stage number, reflux ratio and feed stage about the pressure-swing distillation are optimized. Some better process parameters are as follows: for ethyl acetate refining tower, the pressure is 500.0 kPa, theoretical stage number is 16, reflux ratio is 0.6, feed stage is 5; for crude ethanol tower, the pressure is 101.3 kPa, theoretical stage number is 15, reflux ratio is 0.3, feed stage is 4; for ethanol tower, the pressure is 101.3 kPa, theoretical stage number is 25, reflux ratio is 1.2, feed stage is 10. The mass fraction of ethyl acetate in the bottom of the ethyl acetate refining tower reaches 0.9990, the mass fraction of ethanol in the top of the ethanol tower tower reaches 0.9017, the mass fraction of water in the bottom of the ethanol tower tower reaches 0.9622, and there is also no ethyl acetate in the bottom of the ethanol tower. With laboratory tests, experimental results are in good agreement with the simulation results, which indicates that the separation of ethyl acetate ethanol water can be realized by the pressure-swing distillation separation process. Moreover, it has certain practical significance to industrial practice.

  6. Quasi-stiffness of the knee joint in flexion and extension during the golf swing.

    Science.gov (United States)

    Choi, Ahnryul; Sim, Taeyong; Mun, Joung Hwan

    2015-01-01

    Biomechanical understanding of the knee joint during a golf swing is essential to improve performance and prevent injury. In this study, we quantified the flexion/extension angle and moment as the primary knee movement, and evaluated quasi-stiffness represented by moment-angle coupling in the knee joint. Eighteen skilled and 23 unskilled golfers participated in this study. Six infrared cameras and two force platforms were used to record a swing motion. The anatomical angle and moment were calculated from kinematic and kinetic models, and quasi-stiffness of the knee joint was determined as an instantaneous slope of moment-angle curves. The lead knee of the skilled group had decreased resistance duration compared with the unskilled group (P knee was lower than that of the trail knee in the skilled group (P knee of the skilled golfers had greater flexible excursion duration than the trail knee of the skilled golfers, and of both the lead and trail knees of the unskilled golfers. These results provide critical information for preventing knee injuries during a golf swing and developing rehabilitation strategies following surgery.

  7. Simulated Lunar Testing of Metabolic Heat Regenerated Temperature Swing Adsorption Technology

    Science.gov (United States)

    Padilla, Sebastian A.; Bower, Chad; Iacomini, Christie S.; Paul, H.

    2011-01-01

    Metabolic heat regenerated Temperature Swing Adsorption (MTSA) technology is being developed for thermal and carbon dioxide (CO2) control for a Portable Life Support System (PLSS), as well as water recycling. An Engineering Development Unit (EDU) of the MTSA subassembly was designed and assembled for optimized Martian operations, but also meets system requirements for lunar operations. For lunar operations the MTSA sorption cycle is driven via a vacuum swing between suit ventilation loop pressure and lunar vacuum. The focus of this effort is operations and testing in a simulated lunar environment. This environment was simulated in Paragon s EHF vacuum chamber. The objective of this testing was to evaluate the full cycle performance of the MTSA Subassembly EDU, and to assess CO2 loading and pressure drop of the wash coated aluminum reticulated foam sorbent bed. The lunar testing proved out the feasibility of pure vacuum swing operation, making MTSA a technology that can be tested and used on the Moon prior to going to Mars. Testing demonstrated better than expected CO2 loading on the sorbent and nearly replicates the equilibrium data from the sorbent manufacturer. This had not been achieved in any of the previous sorbent loading tests performed by Paragon. Subsequently, the increased performance of the sorbent bed design indicates future designs will require less mass and volume than the current EDU rendering MTSA as very competitive for Martian PLSS applications.

  8. Wireless inclinometer acquisition system for reducing swing movement control module experiment of hook model

    Science.gov (United States)

    Yu, Yan; Ou, Jinping; Zhang, Chunwei; Li, Luyu

    2008-03-01

    Large Scale Heavy Derrick Lay Barge is very important for sea work. Under intense wind and wave load, the hook on the Barge will vibrate so large that in some cases it can not work. Through installing the Tuned Mass Damper(TMD) on the hook, the vibration will be reduced to a certain range to meet the demand on sea work, which is also important for increasing the efficiency of sea work. To design the suitable TMD for the hook, the dynamical parameters should be specified beforehand. Generally, the related dynamical parameters such as inclinometer and acceleration are measured by wire sensors. But due to the restriction of the actual condition, the wire sensors are very hard to implement. Recently, the wireless sensors have been presented to overcome the shortcomings of wire ones. It is more suitable and also convenient to utilize wireless sensors to acquire the useful data of large scale heavy derrick lay barge. In this paper, the hook reducing swing movement control module is designed for large scale heavy derrick lay barge. Secondly, wireless inclinometer sensor system is integrated using the technique of MEMS, sensing and wireless communication. Finally, the hook reducing swing movement control module is validated by the developed wireless inclinometer data acquisition system. The wireless inclinometer sensor can be used not only in swing monitoring for large scale heavy derrick lay barge's Hook, but also in vibration monitoring for TV tower, large crane. In general, it has great application foreground.

  9. Nonlinearity in oscillating bridges

    Directory of Open Access Journals (Sweden)

    Filippo Gazzola

    2013-09-01

    Full Text Available We first recall several historical oscillating bridges that, in some cases, led to collapses. Some of them are quite recent and show that, nowadays, oscillations in suspension bridges are not yet well understood. Next, we survey some attempts to model bridges with differential equations. Although these equations arise from quite different scientific communities, they display some common features. One of them, which we believe to be incorrect, is the acceptance of the linear Hooke law in elasticity. This law should be used only in presence of small deviations from equilibrium, a situation which does not occur in widely oscillating bridges. Then we discuss a couple of recent models whose solutions exhibit self-excited oscillations, the phenomenon visible in real bridges. This suggests a different point of view in modeling equations and gives a strong hint how to modify the existing models in order to obtain a reliable theory. The purpose of this paper is precisely to highlight the necessity of revisiting the classical models, to introduce reliable models, and to indicate the steps we believe necessary to reach this target.

  10. Between the Dance Studio and the Social Dance Floor: On Solidarity and Practices of Mutuality in Swing Dance Communities

    Directory of Open Access Journals (Sweden)

    Boštjan Kravanja

    2014-07-01

    Full Text Available This article discusses the dynamics of actualization of solidarity and hierarchical relations in contemporary swing dance communities. It shows how these communities are based on a specific solidarity ideology, at least it terms of dealing with processes of their institutionalization, commercialization and establishing of formal dance hierarchies. However, when we take into view the swing dancers themselves, diverse practices of mutuality become evident. In contrast to the formal solidarity discourses and practices, the latter are much more heterogeneous and as such more interesting for anthropological discussion, for they establish solidarity and hierarchical relations apart from wider mobilization movements of the swing dance industry, and many of them implicitly resist institutionalization. The thesis arising from this case study is that the practices of mutuality are not always in complementary relation with discourses of solidarity. On the contrary, they often bypass the major solidarity flows and, paradoxically, contribute most efficiently to the actual solidarity of vital parts of the swing communities. The author discusses the subject on the basis of six years of active participation in different Slovene swing dance scenes and occasional presence at international swing dance events in different European cities.

  11. Active Control of Suspension Bridges

    DEFF Research Database (Denmark)

    Thoft-Christensen, Palle

    In this paper some recent research on active control of very long suspension bridges, is presented. The presentation is based on research work at Aalborg University, Denmark. The active control system is based on movable flaps attached to the bridge girder. Wind load on bridges with or without...... flaps attached to the girder is briefly presented. A simple active control system is discussed. Results from wind tunnel experiments with a bridge section show that flaps can be used effectively to control bridge girder vibrations. Flutter conditions for suspension bridges with and without flaps...... are presented. The theory is illustrated by an example....

  12. 47 CFR 80.1007 - Bridge-to-bridge radiotelephone installation.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 5 2010-10-01 2010-10-01 false Bridge-to-bridge radiotelephone installation. 80.1007 Section 80.1007 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) SAFETY AND... Bridge-to-Bridge Act § 80.1007 Bridge-to-bridge radiotelephone installation. Use of the bridge-to-bridge...

  13. Istanbul Bridge Conference 2014

    CERN Document Server

    Gülkan, Polat; Mahmoud, Khaled

    2016-01-01

      The book includes peer-reviewed contributions selected from presentations given at the Istanbul Bridge Conference 2014, held from August 11 – 13 in Istanbul, Turkey. It reports on the current challenges in bridge engineering faced by professionals around the globe, giving a special emphasis to recently developed techniques, innovations and opportunities. The book covers key topics in the field, including modeling and analysis methods; construction and erection techniques; design for extreme events and condition assessment and structural health monitoring. There is a balanced presentation of theory, research and practice. This book, which provides the readers with a comprehensive and timely reference guide on current practices in bridge engineering, is intended for professionals, academic researchers and students alike.

  14. Bridge deterioration models to support Indiana's bridge management system.

    Science.gov (United States)

    2016-02-01

    An effective bridge management system that is equipped with reliable deterioration models enables agency engineers to carry out : monitoring and long-term programming of bridge repair actions. At the project level, deterioration models help the agenc...

  15. Development of bridge girder movement criteria for accelerated bridge construction.

    Science.gov (United States)

    2014-06-01

    End diaphragms connect multiple girders to form a bridge superstructure system for effective resistance to earthquake loads. Concrete : girder bridges that include end diaphragms consistently proved to perform well during previous earthquake events. ...

  16. Linguistic Barriers and Bridges

    DEFF Research Database (Denmark)

    Thuesen, Frederik

    2016-01-01

    The influence of language on social capital in low-skill and ethnically diverse workplaces has thus far received very limited attention within the sociology of work. As the ethnically diverse workplace is an important social space for the construction of social relations bridging different social...... and intercultural communication, this article analyses interviews with 31 employees from two highly ethnically diverse Danish workplaces. The article shows how linguistic barriers such as different levels of majority language competence and their consequent misunderstandings breed mistrust and hostility, whilst...... communication related to collaboration and ‘small talk’ may provide linguistic bridges to social capital formation....

  17. Bridge the Gap

    DEFF Research Database (Denmark)

    Marselis, Randi

    2017-01-01

    This article focuses on photo projects organised for teenage refugees by the Society for Humanistic Photography (Berlin, Germany). These projects, named Bridge the Gap I (2015), and Bridge the Gap II (2016), were carried out in Berlin and brought together teenagers with refugee and German-majorit...... was produced – and sometimes not produced - within the projects. The importance of memory work in the context of refugee resettlement is often overlooked, but is particularly relevant when cultural encounters are organised in museums and exhibition galleries....

  18. BUILDING "BRIDGES" WITH QUALITY ASSURANCE

    Science.gov (United States)

    The papr describes how, rather than building "bridges" across centuries, quality assurance (QA) personnel have the opportunity to build bridges across technical disciplines, between public and private organizations, and between different QA groups. As reviewers and auditors of a...

  19. Public response to bridge colors.

    Science.gov (United States)

    1973-01-01

    To determine people's reactions to bridges painted in colors as white, yellow, green, blue, red, brown, black, and aluminum, two test bridges were selected in Charlottesville, Virginia. One was painted a different color each month and the other was k...

  20. Bridge-Vehicle Impact Assessment

    Science.gov (United States)

    2011-08-01

    Bridges in New York State have been experiencing close to 200 bridge hits a year. These : accidents are attributed to numerous factors including: improperly stored equipment on trucks; : violation of vehicle posting signs; illegal commercial vehicles...

  1. Colorado statewide historic bridge inventory.

    Science.gov (United States)

    2011-05-01

    The purpose of the Colorado statewide historic bridge inventory was to document and evaluate the National : Register of Historic Places eligibility all on-system highway bridges and grade separation structures built in : Colorado between 1959 and 196...

  2. Virginia Bridge Information Systems Laboratory.

    Science.gov (United States)

    2014-06-01

    This report presents the results of applied data mining of legacy bridge databases, focusing on the Pontis and : National Bridge Inventory databases maintained by the Virginia Department of Transportation (VDOT). Data : analysis was performed using a...

  3. Looking Beyond the Bridge

    DEFF Research Database (Denmark)

    Jahn, Elke; Rosholm, Michael

    We perform a comprehensive analysis of the stepping-stone effect of temporary agency employment on unemployed workers. Using the timing-of-events approach, we not only investigate whether agency employment is a bridge into regular employment but also analyze its effect on post-unemployment wages...

  4. Bridging the Gap?

    Science.gov (United States)

    Salter, Colin

    2009-01-01

    The political context of the conversion of the Historic Tramway Bridge, adjacent to Sandon Point in Bulli (NSW, Australia), and how this was exploited to serve predetermined ends, illustrates that technologies can be designed to have particular social (and political) effects. Through reflection on this relatively small engineering project, this…

  5. Building a Straw Bridge

    Science.gov (United States)

    Teaching Science, 2015

    2015-01-01

    This project is for a team of students (groups of two or three are ideal) to design and construct a model of a single-span bridge, using plastic drinking straws as the building material. All steps of the design, construction, testing and critiquing stages should be recorded by students in a journal. Students may like to include labelled diagrams,…

  6. Bridge over troubled water?

    DEFF Research Database (Denmark)

    Svendsen, Gunnar Lind Haase; Nannestad, Peter; Svendsen, Gert Tinggaard

    2008-01-01

    The problem of integrating non-Western immigrants into Western welfare states is the focus of this paper. To address this issue, we suggest a social capital approach in which we apply the conceptual pair of bridging social capital (BR), which connects an individual to the broader social structure...

  7. Quantum Bidding in Bridge

    Science.gov (United States)

    Muhammad, Sadiq; Tavakoli, Armin; Kurant, Maciej; Pawłowski, Marcin; Żukowski, Marek; Bourennane, Mohamed

    2014-04-01

    Quantum methods allow us to reduce communication complexity of some computational tasks, with several separated partners, beyond classical constraints. Nevertheless, experimental demonstrations of this have thus far been limited to some abstract problems, far away from real-life tasks. We show here, and demonstrate experimentally, that the power of reduction of communication complexity can be harnessed to gain an advantage in a famous, immensely popular, card game—bridge. The essence of a winning strategy in bridge is efficient communication between the partners. The rules of the game allow only a specific form of communication, of very low complexity (effectively, one has strong limitations on the number of exchanged bits). Surprisingly, our quantum technique does not violate the existing rules of the game (as there is no increase in information flow). We show that our quantum bridge auction corresponds to a biased nonlocal Clauser-Horne-Shimony-Holt game, which is equivalent to a 2→1 quantum random access code. Thus, our experiment is also a realization of such protocols. However, this correspondence is not complete, which enables the bridge players to have efficient strategies regardless of the quality of their detectors.

  8. Bridging a Cultural Gap

    Science.gov (United States)

    Leviatan, Talma

    2008-01-01

    There has been a broad wave of change in tertiary calculus courses in the past decade. However, the much-needed change in tertiary pre-calculus programmes--aimed at bridging the gap between high-school mathematics and tertiary mathematics--is happening at a far slower pace. Following a discussion on the nature of the gap and the objectives of a…

  9. DOE Information Bridge

    CERN Document Server

    United States. Department of Energy. Office of Scientific and Technical Information

    DOE Information Bridge, a component of EnergyFiles, provides free, convenient, and quick access to full-text DOE research and development reports in physics, chemistry, materials, biology, environmental sciences, energy technologies, engineering, computer and information science, renewable energy, and other topics. This vast collection includes over 43,000 reports that have been received and processed by OSTI since January 1995.

  10. Revised Rules for Concrete Bridges

    DEFF Research Database (Denmark)

    Thoft-Christensen, Palle; Jensen, F. M.; Middleton, C.

    This paper is based on research performed for the Highway Agency, London, UK under the project DPU/9/44 "Revision of Bridge Assessment Rules Based on Whole Life Performance: Concrete Bridges" It contains details of a methodology which can be used to generate Whole Life (WL) reliability profiles....... These WL reliability profiles may be used to establish revised rules for Concrete Bridges....

  11. Altered kinematics of arm swing in Parkinson's disease patients indicates declines in gait under dual-task conditions.

    Science.gov (United States)

    Baron, Elise I; Miller Koop, Mandy; Streicher, Matthew C; Rosenfeldt, Anson B; Alberts, Jay L

    2018-03-01

    Declines in simultaneous performance of a cognitive and motor task are present in Parkinson's disease due to compromised basal ganglia function related to information processing. The aim of this project was to determine if biomechanical measures of arm swing could be used as a marker of gait function under dual-task conditions in Parkinson's disease patients. Twenty-three patients with Parkinson's disease completed single and dual-task cognitive-motor tests while walking on a treadmill at a self-selected rate. Multiple cognitive domains were evaluated with five cognitive tests. Cognitive tests were completed in isolation (single-task) and simultaneously with gait (dual-task). Upper extremity biomechanical data were gathered using the Motek CAREN system. Primary outcomes characterizing arm swing were: path length, normalized jerk, coefficient of variation of arm swing time, and cognitive performance. Performance on the cognitive tasks were similar across single and dual-task conditions. However, biomechanical measures exhibited significant changes between single and dual-task conditions, with the greatest changes occurring in the most challenging conditions. Arm swing path length decreased significantly from single to dual-task, with the greatest decrease of 21.16%. Jerk, characterizing smoothness, increased significantly when moving from single to dual-task conditions. The simultaneous performance of a cognitive and gait task resulted in decrements in arm swing while cognitive performance was maintained. Arm swing outcomes provide a sensitive measure of declines in gait function in Parkinson's disease under dual-task conditions. The quantification of arm swing is a feasible approach to identifying and evaluating gait related declines under dual-task conditions. Copyright © 2017. Published by Elsevier Ltd.

  12. Double Swing

    DEFF Research Database (Denmark)

    Clausen, Lisbeth

    2017-01-01

    There are two main streams of understanding intercultural communication. The “classic” transmission models include the basic elements of communication involved in sending messages from a sender to a receiver. These models enable analysis of all communication elements and effects by focusing...

  13. Swinging Networks

    Czech Academy of Sciences Publication Activity Database

    Hadrava, Michal; Hlinka, Jaroslav

    2016-01-01

    Roč. 17, suppl. 1 (2016), P146 ISSN 1471-2202 R&D Projects: GA MZd(CZ) NV15-29835A; GA ČR(CZ) GA14-02634S Institutional support: RVO:67985807 Keywords : neurodynamics * connectivity * music * epilepsy Subject RIV: FH - Neurology https://bmcneurosci.biomedcentral.com/articles/10.1186/s12868-016-0283-6

  14. Testing and Results of Vacuum Swing Adsorption Units for Spacesuit Carbon Dioxide and Humidity Control

    Science.gov (United States)

    McMillin, Summer D.; Broerman, Craig D.; Swickrath, Michael; Anderson, Molly

    2011-01-01

    A principal concern for extravehicular activity (EVA) spacesuits is the capability to control carbon dioxide (CO2) and humidity (H2O) for the crewmember. The release of CO2 in a confined or unventilated area is dangerous for human health and leads to asphyxiation; therefore, CO2 and H2O control become leading factors in the design and development of the spacesuit. An amine-based CO2 and H2O vapor sorbent for use in pressure-swing regenerable beds has been developed by Hamilton Sundstrand. The application of solidamine materials with vacuum swing adsorption technology has shown the capacity to concurrently manage CO2 and H2O levels through a fully regenerative cycle eliminating mission constraints imposed with nonregenerative technologies. Two prototype solid amine-based systems, known as rapid cycle amine (RCA), were designed to continuously remove CO2 and H2O vapor from a flowing ventilation stream through the use of a two-bed amine based, vacuum-swing adsorption system. The Engineering and Science Contract Group (ESCG) RCA implements radial flow paths, whereas the Hamilton Sundstrand RCA was designed with linear flow paths. Testing was performed in a sea-level pressure environment and a reduced-pressure environment with simulated human metabolic loads in a closed-loop configuration. This paper presents the experimental results of laboratory testing for a full-size and a sub-scale test article. The testing described here characterized and evaluated the performance of each RCA unit at the required Portable Life Support Subsystem (PLSS) operating conditions. The test points simulated a range of crewmember metabolic rates. The experimental results demonstrated the ability of each RCA unit to sufficiently remove CO2 and H2O from a closed loop ambient or sub-ambient atmosphere.

  15. Biomechanical factors behind toe clearance during the swing phase in hemiparetic patients.

    Science.gov (United States)

    Matsuda, Fumihiro; Mukaino, Masahiko; Ohtsuka, Kei; Tanikawa, Hiroki; Tsuchiyama, Kazuhiro; Teranishi, Toshio; Kanada, Yoshikiyo; Kagaya, Hitoshi; Saitoh, Eiichi

    2017-04-01

    The toe clearance of a paretic limb in the swing phase of gait is related to tripping, which is considered a major cause of falls. The biomechanical factors for obtaining toe clearance are more complicated in hemiparetic gait than that in normal gait because of the compensatory movements during swing phase. Understanding the biomechanical factors should help in targeting the point for rehabilitative interventions. To clarify the biomechanical factors behind toe clearance during swing phase in hemiparetic gait. Fifty patients with hemiparesis after a stroke participated in this study. Three-dimensional motion analysis was used for the kinematic analysis of the hemiparetic gait. The correlation coefficients between limb shortening and angle changes and between limb shortening and hip elevation and foot lateral shift were calculated. Limb shortening was defined as the shortening of the hip-toe distance. The significant factors that determine toe clearance were examined by multiple regression analysis. Independent variables were limb shortening, hip elevation, and foot lateral shift. Limb shortening was negatively correlated with hip elevation (r = -0.75) and foot lateral shift (r = -0.41). Multiple regression analysis showed a significant contribution of limb shortening and hip elevation to toe clearance. The coefficient of determination was 0.95. Toe clearance was mainly determined by limb shortening and hip elevation, which were found to be in a trade-off relationship. These results warrant further investigation into the use of three-dimensional motion analysis in the rehabilitation clinic to facilitate targeted rehabilitative training to restore gait ability.

  16. Active gate driving method for reliability improvement of IGBTs via junction temperature swing reduction

    DEFF Research Database (Denmark)

    Luo, Haoze; Iannuzzo, Francesco; Ma, Ke

    2016-01-01

    This paper introduces an advanced gate driver used as thermal swing control method for the reduction of AC load current-related ΔTj in Insulated-Gate Bipolar Transistors (IGBTs). A switchable gate resistor network is applied to the advanced gate driver, so that the switching power losses can...... be changed according to the amplitude of AC current. Accordingly, a closed-loop thermal control method including the functions of root-mean-square calculation and phase analysis is proposed. Hence ΔTj can be reduced by means of changing losses-related gate resistors on the basis of output fundamental...

  17. The effect of spin in swing bowling in cricket: model trajectories for spin alone

    Science.gov (United States)

    Robinson, Garry; Robinson, Ian

    2015-02-01

    In ‘swing’ bowling, as employed by fast and fast-medium bowlers in cricket, back-spin along the line of the seam is normally applied in order to keep the seam vertical and to provide stability against ‘wobble’ of the seam. Whilst spin is normally thought of as primarily being the slow bowler's domain, the spin applied by the swing bowler has the side-effect of generating a lift or Magnus force. This force, depending on the orientation of the seam and hence that of the back-spin, can have a side-ways component as well as the expected vertical ‘lift’ component. The effect of the spin itself, in influencing the trajectory of the fast bowler's delivery, is normally not considered, presumably being thought of as negligible. The purpose of this paper is to investigate, using calculated model trajectories, the amount of side-ways movement due to the spin and to see how this predicted movement compares with the total observed side-ways movement. The size of the vertical lift component is also estimated. It is found that, although the spin is an essential part of the successful swing bowler's delivery, the amount of side-ways movement due to the spin itself amounts to a few centimetres or so, and is therefore small, but perhaps not negligible, compared to the total amount of side-ways movement observed. The spin does, however, provide a considerable amount of lift compared to the equivalent delivery bowled without spin, altering the point of pitching by up to 3 m, a very large amount indeed. Thus, for example, bowling a ball with the seam pointing directly down the pitch and not designed to swing side-ways at all, but with the amount of back-spin varied, could provide a very powerful additional weapon in the fast bowler's arsenal. So-called ‘sling bowlers’, who use a very low arm action, can take advantage of spin since effectively they can apply side-spin to the ball, giving rise to a large side-ways movement, ˜ 20{}^\\circ cm or more, which certainly is

  18. A Resolution of the Purchasing Power Parity Puzzle: Imperfect Knowledge and Long Swings

    DEFF Research Database (Denmark)

    Frydman, Roman; Goldberg, Michael D.; Johansen, Søren

    2009-01-01

    Asset prices undergo long swings that revolve around benchmark levels. In currency markets, fluctuations involve real exchange rates that are highly persistent and that move in near-parallel fashion with nominal rates. The inability to explain these two regularities with one model has been called...... the "purchasing power parity puzzle." In this paper, we trace the puzzle to exchange rate modelers' use of the "Rational Expectations Hypothesis." We show that once imperfect knowledge is recognized, a monetary model is able to account for the puzzle, as well as other salient features of the data, including...

  19. Rapid Temperature Swing Adsorption using Polymeric/Supported Amine Hollow Fibers

    Energy Technology Data Exchange (ETDEWEB)

    Chance, Ronald [Georgia Tech Research Corporation, Atlanta, GA (United States); Chen, Grace [Georgia Tech Research Corporation, Atlanta, GA (United States); Dai, Ying [Georgia Tech Research Corporation, Atlanta, GA (United States); Fan, Yanfang [Georgia Tech Research Corporation, Atlanta, GA (United States); Jones, Christopher [Georgia Tech Research Corporation, Atlanta, GA (United States); Kalyanaraman, Jayashree [Georgia Tech Research Corporation, Atlanta, GA (United States); Kawajiri, Yoshiaki [Georgia Tech Research Corporation, Atlanta, GA (United States); Koros, William [Georgia Tech Research Corporation, Atlanta, GA (United States); Lively, Ryan [Georgia Tech Research Corporation, Atlanta, GA (United States); McCool, Benjamin [Georgia Tech Research Corporation, Atlanta, GA (United States); Pang, Simon [Georgia Tech Research Corporation, Atlanta, GA (United States); Realff, Matthew [Georgia Tech Research Corporation, Atlanta, GA (United States); Rezaei, Fateme [Georgia Tech Research Corporation, Atlanta, GA (United States); Searcy, Katherine [Georgia Tech Research Corporation, Atlanta, GA (United States); Sholl, David [Georgia Tech Research Corporation, Atlanta, GA (United States); Subramanian, Swernath [Georgia Tech Research Corporation, Atlanta, GA (United States); Pang, Simon [Georgia Tech Research Corporation, Atlanta, GA (United States)

    2015-03-31

    This project is a bench-scale, post-combustion capture project carried out at Georgia Tech (GT) with support and collaboration with GE, Algenol Biofuels, Southern Company and subcontract to Trimeric Corporation. The focus of the project is to develop a process based on composite amine-functionalized oxide / polymer hollow fibers for use as contactors in a rapid temperature swing adsorption post-combustion carbon dioxide capture process. The hollow fiber morphology allows coupling of efficient heat transfer with effective gas contacting, potentially giving lower parasitic loads on the power plant compared to traditional contacting strategies using solid sorbents.

  20. Sensitivity based Assessment of Transient Voltage Sags caused by Rotor Swings

    DEFF Research Database (Denmark)

    Weckesser, Johannes Tilman Gabriel; Jóhannsson, Hjörtur; Østergaard, Jacob

    2014-01-01

    The paper introduces an approach to investigate voltage sags, which are caused by large generator rotor swings following a transient disturbance. Therefore, the method exploits sensitivities derived from the algebraic network equations. These provide information on the impact of a generator...... on the voltage magnitude at a load bus and the effect of load variation on the generator’s power injection. It is shown that these sensitivities give valuable information to identify critical generator-load pairs and locations for applying preventive control measures....

  1. Derivation and application of sensitivities to assess transient voltage sags caused by rotor swings

    DEFF Research Database (Denmark)

    Weckesser, Johannes Tilman Gabriel; Jóhannsson, Hjörtur; Østergaard, Jacob

    2015-01-01

    The paper introduces an approach to investigate voltage sags, which are caused by large generator rotor swings following a transient disturbance. Therefore, the method exploits sensitivities derived from the algebraic network equations. These provide information on the impact of a generator...... on the voltage magnitude at a load bus and the effect of load variation on the generator’s power injection. It is shown that these sensitivities give valuable information to identify critical generator–load pairs and locations for applying preventive control measures....

  2. The effect of spin in swing bowling in cricket: model trajectories for spin alone

    International Nuclear Information System (INIS)

    Robinson, Garry; Robinson, Ian

    2015-01-01

    In ‘swing’ bowling, as employed by fast and fast-medium bowlers in cricket, back-spin along the line of the seam is normally applied in order to keep the seam vertical and to provide stability against ‘wobble’ of the seam. Whilst spin is normally thought of as primarily being the slow bowler's domain, the spin applied by the swing bowler has the side-effect of generating a lift or Magnus force. This force, depending on the orientation of the seam and hence that of the back-spin, can have a side-ways component as well as the expected vertical ‘lift’ component. The effect of the spin itself, in influencing the trajectory of the fast bowler's delivery, is normally not considered, presumably being thought of as negligible. The purpose of this paper is to investigate, using calculated model trajectories, the amount of side-ways movement due to the spin and to see how this predicted movement compares with the total observed side-ways movement. The size of the vertical lift component is also estimated. It is found that, although the spin is an essential part of the successful swing bowler's delivery, the amount of side-ways movement due to the spin itself amounts to a few centimetres or so, and is therefore small, but perhaps not negligible, compared to the total amount of side-ways movement observed. The spin does, however, provide a considerable amount of lift compared to the equivalent delivery bowled without spin, altering the point of pitching by up to 3 m, a very large amount indeed. Thus, for example, bowling a ball with the seam pointing directly down the pitch and not designed to swing side-ways at all, but with the amount of back-spin varied, could provide a very powerful additional weapon in the fast bowler's arsenal. So-called ‘sling bowlers’, who use a very low arm action, can take advantage of spin since effectively they can apply side-spin to the ball, giving rise to a large side-ways movement, ∼20 ∘ cm or more, which

  3. System and process for polarity swing assisted regeneration of gas selective capture liquids

    Science.gov (United States)

    Heldebrant, David J.; Tegrotenhuis, Ward E.; Freeman, Charles J.; Elliott, Michael L.; Koech, Phillip K.; Humble, Paul H.; Zheng, Feng; Zhang, Jian

    2017-07-18

    A polarity swing-assisted regeneration (PSAR) process is disclosed for improving the efficiency of releasing gases chemically bound to switchable ionic liquids. Regeneration of the SWIL involves addition of a quantity of non-polar organic compound as an anti-solvent to destabilize the SWIL, which aids in release of the chemically bound gas. The PSAR decreases gas loading of a SWIL at a given temperature and increases the rate of gas release compared to heating in the absence of anti-solvent.

  4. A Comparison of Jump Height, Takeoff Velocities, and Blocking Coverage in the Swing and Traditional Volleyball Blocking Techniques

    Directory of Open Access Journals (Sweden)

    Travis Ficklin

    2014-03-01

    Full Text Available The purpose of this study was to compare traditional and swing blocking techniques on center of mass (COM projectile motion and effective blocking area in nine healthy Division I female volleyball players. Two high-definition (1080 p video cameras (60 Hz were used to collect two-dimensional variables from two separate views. One was placed perpendicular to the plane of the net and the other was directed along the top of the net, and were used to estimate COM locations and blocking area in a plane parallel to the net and hand penetration through the plane of the net respectively. Video of both the traditional and swing techniques were digitized and kinematic variables were calculated. Paired samples t-tests indicated that the swing technique resulted in greater (p < 0.05 vertical and horizontal takeoff velocities (vy and vx, jump height (H, duration of the block (tBLOCK, blocking coverage during the block (C as well as hand penetration above and through the net’s plane (YPEN, ZPEN. The traditional technique had significantly greater approach time (tAPP. The results of this study suggest that the swing technique results in both greater jump height and effective blocking area. However, the shorter tAPP that occurs with swing is associated with longer times in the air during the block which may reduce the ability of the athlete to make adjustments to attacks designed to misdirect the defense.

  5. Anti-Swing Control of Gantry and Tower Cranes Using Fuzzy and Time-Delayed Feedback with Friction Compensation

    Directory of Open Access Journals (Sweden)

    H.M. Omar

    2005-01-01

    Full Text Available We designed a feedback controller to automate crane operations by controlling the load position and its swing. First, a PD tracking controller is designed to follow a prescribed trajectory. Then, another controller is added to the control loop to damp the load swing. The anti-swing controller is designed based on two techniques: a time-delayed feedback of the load swing angle and an anti-swing fuzzy logic controller (FLC. The rules of the FLC are generated by mapping the performance of the time-delayed feedback controller. The same mapping method used for generating the rules can be applied to mimic the performance of an expert operator. The control algorithms were designed for gantry cranes and then extended to tower cranes by considering the coupling between the translational and rotational motions. Experimental results show that the controller is effective in reducing load oscillations and transferring the load in a reasonable time. To experimentally validate the theory, we had to compensate for friction. To this end, we estimated the friction and then applied a control action to cancel it. The friction force was estimated by assuming a mathematical model and then estimating the model coefficients using an off-line identification technique, the method of least squares (LS.

  6. Kettlebell swing, snatch, and bottoms-up carry: back and hip muscle activation, motion, and low back loads.

    Science.gov (United States)

    McGill, Stuart M; Marshall, Leigh W

    2012-01-01

    The intent of this study was to quantify spine loading during different kettlebell swings and carries. No previously published studies of tissue loads during kettlebell exercises could be found. Given the popularity of kettlebells, this study was designed to provide an insight into the resulting joint loads. Seven male subjects participated in this investigation. In addition, a single case study of the kettlebell swing was performed on an accomplished kettlebell master. Electromyography, ground reaction forces (GRFs), and 3D kinematic data were recorded during exercises using a 16-kg kettlebell. These variables were input into an anatomically detailed biomechanical model that used normalized muscle activation; GRF; and spine, hip, and knee motion to calculate spine compression and shear loads. It was found that kettlebell swings create a hip-hinge squat pattern characterized by rapid muscle activation-relaxation cycles of substantial magnitudes (∼50% of a maximal voluntary contraction [MVC] for the low back extensors and 80% MVC for the gluteal muscles with a 16-kg kettlebell) resulting in about 3,200 N of low back compression. Abdominal muscular pulses together with the muscle bracing associated with carries create kettlebell-specific training opportunities. Some unique loading patterns discovered during the kettlebell swing included the posterior shear of the L4 vertebra on L5, which is opposite in polarity to a traditional lift. Thus, quantitative analysis provides an insight into why many individuals credit kettlebell swings with restoring and enhancing back health and function, although a few find that they irritate tissues.

  7. BALKANS: Building bridges

    International Nuclear Information System (INIS)

    Anon.

    1991-01-01

    At a time when upheaval and political unrest in some Balkan countries gives cause for concern, it is good to know that physics, once again, is building bridges between nations. The new international mobility in the region was marked by a major activity of the Balkan Physical Union - the first Balkan School of Physics, held on the banks of the Bosphorus during the first two weeks of September

  8. Differences in wrist mechanics during the golf swing based on golf handicap.

    Science.gov (United States)

    Fedorcik, Gregory G; Queen, Robin M; Abbey, Alicia N; Moorman, Claude T; Ruch, David S

    2012-05-01

    Variation in swing mechanics between golfers of different skill levels has been previously reported. To investigate if differences in three-dimensional wrist kinematics and the angle of golf club descent between low and high handicap golfers. A descriptive laboratory study was performed with twenty-eight male golfers divided into two groups, low handicap golfers (handicap = 0-5, n = 15) and high handicap golfers (handicap ≥ 10, n = 13). Bilateral peak three-dimensional wrist mechanics, bilateral wrist mechanics at ball contact (BC), peak angle of descent from the end of the backswing to ball contact, and the angle of descent when the forearm was parallel to the ground (DEC-PAR) were determined using an 8 camera motion capture system. Independent t-tests were completed for each study variable (α = 0.05). Pearson correlation coefficients were determined between golf handicap and each of the study variables. The peak lead arm radial deviation (5.7 degrees, p = 0.008), lead arm radial deviation at ball contact (7.1 degrees, p = 0.001), and DEC-PAR (15.8 degrees, p = 0.002) were significantly greater in the high handicap group. In comparison with golfers with a low handicap, golfers with a high handicap have increased radial deviation during the golf swing and at ball contact. Copyright © 2011 Sports Medicine Australia. Published by Elsevier Ltd. All rights reserved.

  9. Orientation of Cells Cultured in Vortex Flow with Swinging Plate in Vitro

    Directory of Open Access Journals (Sweden)

    Shigehiro Hashimoto

    2011-06-01

    Full Text Available An effect of flow on cell culture has been studied in vitro. A silicone disk was placed in the center of culture dish of 52 mm internal diameter to make a doughnut-shaped canal. The dish was placed on a tilted plate, which rotates to make a vortex flow around the silicone disk with a swing motion. Variations were made on the diameter (20 mm, 30 mm, and 40 mm of the silicone disk and the rotational speed (2.1 rad/sec, 5.2 rad/sec of the swinging plate, which tilts with 0.1 rad from the horizontal plane. Five kinds of cells were cultured in the vortex flow of Dulbecco’s Modified Eagle’s Medium for seven days: C2C12 (mouse myoblast, L6 (rat skeletal muscle cell, A7r5 (rat aortic smooth muscle cell, CS-2P2-C75 (primary normal porcine aortic endothelial cell, and L929 (mouse fibroblast. The experiments show the following results. The orientation of cells depends on flow and on kinds of cells. A7r5 and CS-2P2-C75 line along the streamline of the flow. C2C12 and L6 adhere along the direction of the flow in the first stage, and tilt to the perpendicular direction to the flow differentiating to myotubes with fusion in the second stage.

  10. Development of a doorframe-typed swinging seedling pick-up device for automatic field transplantation

    Energy Technology Data Exchange (ETDEWEB)

    Han, H.; Mao, H.; Hu, J.; Tian, K.

    2015-07-01

    A doorframe-typed swing seedling pick-up device for automatic field transplanters was developed and evaluated in a laboratory. The device, consisting of a path manipulator and two grippers, can move the pins slowly to extract seedlings from the tray cells and return quickly to the pick-up point for the next extraction. The path manipulator was constructed with the creative design of type-Ⅱ mechanism combination in series. It consists of an oscillating guide linkage mechanism and a grooved globoidal cam mechanism. The gripper is a pincette-type mechanism using the pick-up pins to penetrate into the root mass for seedling extraction. The dynamic analysis of the designed seedling pick-up device was simulated with ADAMS software. Being the first prototype, various performance tests under local production conditions were conducted to find out the optimal machine operation parameters and transplant production conditions. As the gripper with multiple fine pins was moved by the swing pick-up device, it can effectively complete the transplanting work cycle of extracting, transferring, and discharging a seedling. The laboratory evaluation showed that the pick-up device equipped with two grippers can extract 80 seedlings/min with a 90% success and a 3% failure in discharging seedlings, using 42-day-old tomato plantlets. The quality of extracting seedlings was satisfactory. (Author)

  11. Swing-attenuation for a quadrotor transporting a cable-suspended payload.

    Science.gov (United States)

    Guerrero-Sánchez, M Eusebia; Mercado-Ravell, D Alberto; Lozano, Rogelio; García-Beltrán, C Daniel

    2017-05-01

    This paper presents the problem of safe and fast transportation of packages by an Unmanned Aerial Vehicle (UAV) kind quadrotor. A mathematical model and a control strategy for a special class of underactuated mechanical systems, composed of a quadrotor transporting a cable-suspended payload, are proposed. The Euler-Lagrange formulation is used to obtain the dynamic model of the system, where the integrated dynamics of the quadrotor, cable and payload are considered. An Interconnection and Damping Assignment-Passivity Based Control (IDA-PBC) is chosen because of its inherent robustness against parametric uncertainty and unmodeled dynamics. Two cases are considered to obtain two different control laws, in the first case, the designed control law depends on the swing angle of the payload, in the second case the control law does not depend on it. The control objective is to transport the payload from point to point, with swing reduction along trajectory. Experimental results using monocular vision based navigation are shown to evaluate the proposed control law. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

  12. Solar Power Ramp Events Detection Using an Optimized Swinging Door Algorithm: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Cui, Mingjian; Zhang, Jie; Florita, Anthony; Hodge, Bri-Mathias; Ke, Deping; Sun, Yuanzhang

    2015-08-07

    Solar power ramp events (SPREs) are those that significantly influence the integration of solar power on non-clear days and threaten the reliable and economic operation of power systems. Accurately extracting solar power ramps becomes more important with increasing levels of solar power penetrations in power systems. In this paper, we develop an optimized swinging door algorithm (OpSDA) to detection. First, the swinging door algorithm (SDA) is utilized to segregate measured solar power generation into consecutive segments in a piecewise linear fashion. Then we use a dynamic programming approach to combine adjacent segments into significant ramps when the decision thresholds are met. In addition, the expected SPREs occurring in clear-sky solar power conditions are removed. Measured solar power data from Tucson Electric Power is used to assess the performance of the proposed methodology. OpSDA is compared to two other ramp detection methods: the SDA and the L1-Ramp Detect with Sliding Window (L1-SW) method. The statistical results show the validity and effectiveness of the proposed method. OpSDA can significantly improve the performance of the SDA, and it can perform as well as or better than L1-SW with substantially less computation time.

  13. CFD Simulation for Separation of Carbon Dioxide-Methane Mixture by Pressure Swing Adsorption

    Directory of Open Access Journals (Sweden)

    K. Rambabu

    2014-01-01

    Full Text Available A developing technology for gas separations is pressure swing adsorption, which has been proven to be more economical and energy efficient compared to other separation methods like cryogenic distillation and membrane separation. A pressure swing adsorption (PSA column, with carbon dioxide-methane as feed mixture and 6-FDA based polyimides as the adsorbent, was modeled and simulated in this work. Ansys Fluent 12.1, along with supplementary user defined functions, was used to develop a 2D transient Eulerian laminar viscous flow model for the PSA column. The model was validated by comparing the simulated results with established analytical models for PSA. The developed numerical model was used to determine the carbon dioxide concentration in the column as a function of time based on different operating conditions. Effect of various operating parameters like pressure, temperature, and flow rate on the separation efficiency has been studied and reported. Optimization studies were carried out to obtain suitable operating conditions for the feed gases separation. Simulation studies were carried out to determine the separation length required for complete separation of the feed mixture corresponding to different inlet feed concentrations which were entering the column at a given flow rate.

  14. Getting into the flow: Red cells go on a roll, two-component vesicles swing

    Science.gov (United States)

    Viallat, Annie; Dupire, Jules; Khelloufi, Kamel; Al Halifa, Al Hair; Adhesion and Inflammation Team

    2013-11-01

    Red blood cells are soft capsules. Under shear flow, their two known motions were ``tumbling'' and ``swinging-tank treading,'' depending on cell mechanics and flow conditions. We reveal new wobbling regimes, among which the ``rolling'' regime, where red cells move as wheels on a road. We show, by coupling two video-microscopy approaches providing multi-directional cell pictures that the orientation of cells flipping into the flow is determined by the shear rate. Rolling permits to avoid energetically costly cellular deformations and is a true signature of the cytoskeleton elasticity. We highlight two transient dynamics: an intermittent regime during the ``tank-treading-to-flipping'' transition and a Frisbee-like ``spinning'' regime during the ``rolling-to-tank-treading'' transition. We find that the biconcave red cell shape is very stable under moderate shear stresses, and we interpret this result in terms of shape memory and elastic buckling. Finally, we generate lipid vesicles with a shape memory by using two lipids with different bending rigidities. These vesicles swing in shear flow similarly to red blood cells but their non-axisymmetric stress-free shape changes the periodicity of the motion and induces specific features.

  15. Influence of the Pressure Difference and Door Swing on Heavy Contaminants Migration between Rooms.

    Science.gov (United States)

    Hendiger, Jacek; Chludzińska, Marta; Ziętek, Piotr

    2016-01-01

    This paper presents the results of investigations whose aim was to describe the influence of the pressure difference level on the ability of contaminants migration between neighbouring rooms in dynamic conditions associated with door swing. The analysis was based on airflow visualization made with cold smoke, which simulated the heavy contaminants. The test room was pressurized to a specific level and then the door was opened to observe the trail of the smoke plume in the plane of the door. The door was opened in both directions: to the positively and negatively pressurized room. This study focuses on the visualization of smoke plume discharge and an uncertainty analysis is not applicable. Unlike other studies which focus on the analysis of pressure difference, the present study looks at the contaminants which are heavier than air and on "pumping out" the contaminants by means of door swing. Setting the proper level of pressure difference between the contaminated room and the neighbouring rooms can prove instrumental in ensuring protection against toxic contaminants migration. This study helped to establish the threshold of pressure difference necessary to reduce migration of heavy contaminants to neighbouring rooms.

  16. The influence of the gait-related arm swing on elevation gain measured by sport watches

    Directory of Open Access Journals (Sweden)

    Ammann Rahel

    2016-06-01

    Full Text Available The elevation gain is an important contributor to the total workload in endurance sports. The purpose of this study was to evaluate the influence of the arm swing on elevation gain in three sport watches (Garmin® Forerunner 910XT, Polar® RS800CX and Suunto® Ambit2 on a flat 400 m outdoor track. Altogether, a total of 120 repetitions of 1,200 m were performed at self-selected speeds corresponding to strolling, walking, jogging and running. During the assessment two devices of each sport watch, one secured on the hip and one on the wrist, were worn by the participants. A small but significant (effect size = .39; p < .001 influence of the arm swing on elevation was revealed in all sport watches. Elevation indication errors recorded on the wrist were significantly larger than the ones recorded on the hip (4.0-7.4 vs. 1.2-5.7 m per 1,200 m; p < .05. Furthermore, when wearing the devices on the wrist, errors in elevation indication increased when gait speed increased. Users should be aware that wearing the devices on the hip can significantly decrease measurement errors. This might be especially relevant for activities with high dynamics, such as jogging and running.

  17. Development of Pressure Swing Adsorption Technology for Spacesuit Carbon Dioxide and Humidity Removal

    Science.gov (United States)

    Papale, William; Paul, Heather; Thomas, Gretchen

    2006-01-01

    Metabolically produced carbon dioxide (CO2) removal in spacesuit applications has traditionally been accomplished utilizing non-regenerative Lithium Hydroxide (LiOH) canisters. In recent years, regenerative Metal Oxide (MetOx) has been developed to replace the Extravehicular Mobility Unity (EMU) LiOH canister for extravehicular activity (EVA) missions in micro-gravity, however, MetOx may carry a significant weight burden for potential use in future Lunar or planetary EVA exploration missions. Additionally, both of these methods of CO2 removal have a finite capacity sized for the particular mission profile. Metabolically produced water vapor removal in spacesuits has historically been accomplished by a condensing heat exchanger within the ventilation process loop of the suit life support system. Advancements in solid amine technology employed in a pressure swing adsorption system have led to the possibility of combining both the CO2 and humidity control requirements into a single, lightweight device. Because the pressure swing adsorption system is regenerated to space vacuum or by an inert purge stream, the duration of an EVA mission may be extended significantly over currently employed technologies, while markedly reducing the overall subsystem weight compared to the combined weight of the condensing heat exchanger and current regenerative CO2 removal technology. This paper will provide and overview of ongoing development efforts evaluating the subsystem size required to manage anticipated metabolic CO2 and water vapor generation rates in a spacesuit environment.

  18. Anti-Swing Control of Suspended Loads on Shipboard Robotic Cranes

    Directory of Open Access Journals (Sweden)

    Jackrit Suthakorn

    2005-02-01

    Full Text Available Currently, the speed at which materials can be transferred between ships at sea is limited by sea conditions. Rough sea conditions cause the payload to swing making load transfer difficult and time-consuming. The objective of this research is to develop a real-time, command compensating control for reducing sea state induced payload swing for shipboard robotic cranes. The future use of this control strategy will be to facilitate faster "ship-to-ship" payload transfer in rough sea conditions. In this study, only the sea-induced rotational motion of the ship is considered, since it is assumed that a station-keeping control maintains a constant position of the ship. This rotational motion is modelled using pitch-yaw-roll Euler angles. The shipboard robotic crane is modelled as a spherical pendulum attached to a three-degree-of-freedom manipulator. The three degrees-of-freedom are azimuth (rotation about an axis normal to the ship's deck, elevation (rotation about an axis parallel with the ship's deck, also referred to as luffing, and lift-line length. An inverse kinematics based approach and a sliding mode control strategy are explored. Both approaches use the azimuth and the elevation capability of the crane manipulator to maintain a horizontal position of the suspended load to reduce sea-induced payload sway.

  19. The effect of two different swinging methods upon colic and crying durations among the infants

    Directory of Open Access Journals (Sweden)

    Gamze Yilmaz

    2015-01-01

    Full Text Available Context: Swinging "repetitive and rhythmic" movements are helpful because these provide a continuous stimulus. These methods are reported to be effective upon decreasing baby′s pains or cry. Aim: The purpose of this study was to determine the factors of the two different methods (rhythmic rocking of infants in the arm and rhythmic rocking infants on a blanket on crying duration and colic as well as the factors affecting duration of crying with colic. Materials and Methods: A pre-test post-test quasi experimental model was used. Subjects included 72 infants (1-3 months who had colic and their mothers. The infants were healthy and were delivered after full-term gestation. Results: It has been determined that as the duration of application increased (at the end of the second week, the crying duration of babies who were in each of the two groups decreased. Conclusion: It has been found that swinging ( rhythmic rocking the infants on a blanket and in arm, decreased the colic and crying duration of infants.

  20. The effects of cognitive anxiety on the biomechanical characteristics of the golf swing

    Directory of Open Access Journals (Sweden)

    MBA De Ste Croix

    2008-03-01

    Full Text Available The aim of this study was to examine the effect of cognitive anxiety (CA on the biomechanical characteristics of the golf swing. Written informed consent was obtained from 9 subjects, with a range of golf experience (handicap range 4-23. Each subject was filmed under a low anxiety condition (during practice, and a high anxiety condition (during competition and completed a revised version of the Competitive State Anxiety Inventory-2 (CSAI-2. Human movement analysis (Hu-m-an software package was used to identify the clubhead speeds during the backswing, downswing, and impact time, along with the completion times for each phase. The absolute angle of the club to the vertical, and the relative angle of the forearm, wrist, and club hinge, at the completion of the backswing stage were also examined. CA intensity scores were significantly lower during practice than competition (p<0.05. CA interpretation scores indicate that anxiety symptoms during practice were significantly more facilitative to performance (p<0.05. The time taken to complete the downswing phase was significantly lower during competition (p<0.05. The combined backswing and downswing times were significantly lower during the competition trial (p<0.05. There were no significant differences between the practice and competition trials on any of the remaining swing variables measured.

  1. Development of a doorframe-typed swinging seedling pick-up device for automatic field transplantation

    International Nuclear Information System (INIS)

    Han, H.; Mao, H.; Hu, J.; Tian, K.

    2015-01-01

    A doorframe-typed swing seedling pick-up device for automatic field transplanters was developed and evaluated in a laboratory. The device, consisting of a path manipulator and two grippers, can move the pins slowly to extract seedlings from the tray cells and return quickly to the pick-up point for the next extraction. The path manipulator was constructed with the creative design of type-Ⅱ mechanism combination in series. It consists of an oscillating guide linkage mechanism and a grooved globoidal cam mechanism. The gripper is a pincette-type mechanism using the pick-up pins to penetrate into the root mass for seedling extraction. The dynamic analysis of the designed seedling pick-up device was simulated with ADAMS software. Being the first prototype, various performance tests under local production conditions were conducted to find out the optimal machine operation parameters and transplant production conditions. As the gripper with multiple fine pins was moved by the swing pick-up device, it can effectively complete the transplanting work cycle of extracting, transferring, and discharging a seedling. The laboratory evaluation showed that the pick-up device equipped with two grippers can extract 80 seedlings/min with a 90% success and a 3% failure in discharging seedlings, using 42-day-old tomato plantlets. The quality of extracting seedlings was satisfactory. (Author)

  2. Eight Weeks of Kettlebell Swing Training Does not Improve Sprint Performance in Recreationally Active Females.

    Science.gov (United States)

    Holmstrup, Michael E; Jensen, Brock T; Evans, William S; Marshall, Emily C

    2016-01-01

    The kettlebell swing (KBS), emphasizing cyclical, explosive hip extension in the horizontal plane, aligns with movement- and velocity-specificity of sprinting. The present study examined the effect of an eight-week KBS intervention on sprinting in recreationally-active females, in comparison to an eight-week intervention using the stiff-legged deadlift (SDL). Following a pre-testing session measuring 30 meter sprint and countermovement vertical jump performance, participants were divided evenly by sprint time into KBS (n=8) and SDL (n=10) cohorts. Following familiarization with the exercises, KBS met twice weekly to perform swings using the Tabata interval (20s work, 10s rest, 8 rounds), stressing a rapid, explosive tempo. In contrast, the SDL group performed their Tabata stiff-legged deadlifts at a conventional resistance training tempo (2 seconds concentric, 2 seconds eccentric). Following eight weeks and greater than 95% training adherence, the SDL group only had a slightly greater average training volume (~3%) than KBS. No significant differences in pre-test values, or changes were noted in sprint performance from pre- to post-intervention in either group. An improvement in vertical jump performance was noted across groups. Potential explanations for the lack of sprint improvement compared to previous studies include differences between recreationally-active and athletic females, and low exercise volume (~46% of a comparable study with improvements in vertical jump). Future studies should seek to determine the appropriate volume and intensity for KBS components of sprint programming.

  3. Subthreshold-swing-adjustable tunneling-field-effect-transistor-based random-access memory for nonvolatile operation

    Science.gov (United States)

    Huh, In; Cheon, Woo Young; Choi, Woo Young

    2016-04-01

    A subthreshold-swing-adjustable tunneling-field-effect-transistor-based random-access memory (SAT RAM) has been proposed and fabricated for low-power nonvolatile memory applications. The proposed SAT RAM cell demonstrates adjustable subthreshold swing (SS) depending on stored information: small SS in the erase state ("1" state) and large SS in the program state ("0" state). Thus, SAT RAM cells can achieve low read voltage (Vread) with a large memory window in addition to the effective suppression of ambipolar behavior. These unique features of the SAT RAM are originated from the locally stored charge, which modulates the tunneling barrier width (Wtun) of the source-to-channel tunneling junction.

  4. Design of Low Voltage Low Power CMOS OP-AMPS with Rail-to-Rail Input/Output Swing

    OpenAIRE

    Gopalaiah, SV; Shivaprasad, AP; Panigrahi, Sukanta K

    2004-01-01

    A novel input and output biasing circuit to extend the input common mode (CM) voltage range and the output swing to rail-to-rail in a low voltage op-amp in standard CMOS technology is presented. The input biasing circuit uses a Switched Capacitor Based Attenuator (SCBA) approach to establish rail-to-rail common mode input voltage range. And the output biasing circuit uses an Output Driver (OD), with floating bias to give the rail-to-rail swing at output stage. Three different OD schemes in op...

  5. CO2 Molecule as a Quantum Realization of the 1∶1∶2 Resonant Swing-Spring with Monodromy

    Science.gov (United States)

    Cushman, R. H.; Dullin, H. R.; Giacobbe, A.; Holm, D. D.; Joyeux, M.; Lynch, P.; Sadovskií, D. A.; Zhilinskií, B. I.

    2004-07-01

    We consider the wide class of systems modeled by an integrable approximation to the 3degrees of freedom elastic pendulum with 1∶1∶2 resonance, or the swing-spring. This approximation has monodromy which prohibits the existence of global action-angle variables and complicates the dynamics. We study the quantum swing-spring formed by bending and symmetric stretching vibrations of the CO2 molecule. We uncover quantum monodromy of CO2 as a nontrivial codimension2 defect of the three dimensional energy-momentum lattice of its quantum states.

  6. Testing Hypotheses in an I(2) Model with Applications to the Persistent Long Swings in the Dmk/$ Rate

    DEFF Research Database (Denmark)

    Johansen, Søren; Juselius, Katarina; Frydman, Roman

    and persistent swings in the foreign exchange market between Germany and USA. The data analyzed consist of nominal exchange rates, relative prices, US inflation rate, two long-term interest rates and two short-term interest rates over the 1975-1999 period. One important aim of the paper is to demonstrate...... that by structuring the data with the help of the I(2) model one can achieve a better understanding of the empirical regularities underlying the persistent swings in nominal exchange rates, typical in periods of floating exchange rates...

  7. Simulation of multivariate diffusion bridges

    DEFF Research Database (Denmark)

    Bladt, Mogens; Finch, Samuel; Sørensen, Michael

    We propose simple methods for multivariate diffusion bridge simulation, which plays a fundamental role in simulation-based likelihood and Bayesian inference for stochastic differential equations. By a novel application of classical coupling methods, the new approach generalizes a previously...... proposed simulation method for one-dimensional bridges to the mulit-variate setting. First a method of simulating approzimate, but often very accurate, diffusion bridges is proposed. These approximate bridges are used as proposal for easily implementable MCMC algorithms that produce exact diffusion bridges....... The new method is much more generally applicable than previous methods. Another advantage is that the new method works well for diffusion bridges in long intervals because the computational complexity of the method is linear in the length of the interval. In a simulation study the new method performs well...

  8. Morphological aspects of myocardial bridges.

    Science.gov (United States)

    Lujinović, Almira; Kulenović, Amela; Kapur, Eldan; Gojak, Refet

    2013-11-01

    Although some myocardial bridges can be asymptomatic, their presence often causes coronary disease either through direct compression of the "tunnel" segment or through stimulation and accelerated development of atherosclerosis in the segment proximally to the myocardial bridge. The studied material contained 30 human hearts received from the Department of Anatomy. The hearts were preserved 3 to 5 days in 10% formalin solution. Thereafter, the fatty tissue was removed and arterial blood vessels prepared by careful dissection with special reference to the presence of the myocardial bridges. Length and thickness of the bridges were measured by the precise electronic caliper. The angle between the myocardial bridge fibre axis and other axis of the crossed blood vessel was measured by a goniometer. The presence of the bridges was confirmed in 53.33% of the researched material, most frequently (43.33%) above the anterior interventricular branch. The mean length of the bridges was 14.64 ± 9.03 mm and the mean thickness was 1.23 ± 1.32 mm. Myocardial bridge fibres pass over the descending blood vessel at the angle of 10-90 degrees. The results obtained on a limited sample suggest that the muscular index of myocardial bridge is the highest for bridges located on RIA, but that the difference is not significant in relation to bridges located on other branches. The results obtained suggest that bridges located on other branches, not only those on RIA, could have a great contractive power and, consequently, a great compressive force, which would be exerted on the wall of a crossed blood vessel.

  9. Bridge Aesthetics and Structural Honesty

    DEFF Research Database (Denmark)

    Gimsing, Niels Jørgen

    1999-01-01

    In bridges the overall form must be chosen with due respect to the transmission of forces if efficient structures shall be created, The design must therefore be governed by experienced structural engineers - in some cases assisted by aesthetic advisers on specific issues. Some basic requirements...... decisive for choosing the form of trusses, arches and cable-stayed bridges are outlined, and several examples show bridges designed without giving priority to the structural aspects....

  10. Morphological aspects of myocardial bridges

    Directory of Open Access Journals (Sweden)

    Almira Lujinović

    2013-11-01

    Full Text Available Although some myocardial bridges can be asymptomatic, their presence often causes coronary disease either through direct compression of the “tunnel” segment or through stimulation and accelerated development of atherosclerosis in the segment proximally to the myocardial bridge. The studied material contained 30 human hearts received from the Department of Anatomy. The hearts were preserved 3 to 5 days in 10% formalin solution. Thereafter, the fatty tissue was removed and arterial blood vessels prepared by careful dissection with special reference to the presence of the myocardial bridges. Length and thickness of the bridges were measured by the precise electronic caliper. The angle between the myocardial bridge fibre axis and other axis of the crossed blood vessel was measured by a goniometer. The presence of the bridges was confirmed in 53.33% of the researched material, most frequently (43.33% above the anterior interventricular branch. The mean length of the bridges was 14.64±9.03 mm and the mean thickness was 1.23±1.32 mm. Myocardial bridge fibres pass over the descending blood vessel at the angle of 10-90 degrees. The results obtained on a limited sample suggest that the muscular index of myocardial bridge is the highest for bridges located on RIA, but that the difference is not significant in relation to bridges located on other branches. The results obtained suggest that bridges located on other branches, not only those on RIA, could have a great contractive power and, consequently, a great compressive force, which would be exerted on the wall of a crossed blood vessel.

  11. An innovating method to measure bridge deflection using interference-based sensors

    Science.gov (United States)

    Kung, Peter; Wang, Lutang; Comanici, Maria Iulia

    2012-04-01

    The Vibrofiber sensor is a Fabry-Perot cavity formed between two broad band fiber gratings creating interference fringes. It was introduced three years ago to monitor the vibration and temperature rise of the stator end winding in a power generator.(1) This paper will discuss the use of Vibrofiber to monitor the deflection of the bridge under adverse conditions: wide temperature swings, excess load, strong winds, earth quake, etc. The fringes in these cavity sensors have features like peaks and valleys which are sensitive to temperature and strain. When the bridge becomes overloaded, we are interested in knowing the extent of the deflection. In addition, we might want to locate the cause of the overload. A simple Sagnac FBG interferometer has been invented to provide such diagnostics. A pair of long fibers with such cavity sensors can be installed on the underside of the target bridge segment between two supporting columns. The objective is to monitor the deflection together with any distortion of the bridge deck. Each of the 2 long fiber segments has a pair of cavity sensors, one measures the deflection as a result of the excess strain, and the other measures temperature and provides compensation for the deflection data. An array of cavity sensors with different center wavelengths will be used to support the typical multi-segment bridge structure. The interrogation unit is based on a tunable laser that can hop to different ITU grids. A separate DFB laser will run a grating based Sagnac interferometer, measuring weight in motion, identifying the speed and the make of vehicle in traffic and provide deflection diagnostics. Overloaded trucks and speeding vehicles can be captured and tagged for corrective actions. The interrogation unit is equipped with wireless Ethernet communication enabling the monitoring of many bridges from a central location and similarly warning can be initiated to alert the central traffic control ahead of any problems.

  12. Comprehensive evaluation of fracture critical bridges.

    Science.gov (United States)

    2014-02-01

    Two-girder steel bridges are classified as fracture critical bridges based on the definition given in the AASHTO LRFD Bridge Design Specifications. In a fracture critical bridge a failure of a tension member leads to collapse of the bridge. However, ...

  13. 75 FR 41281 - Bridge Safety Standards

    Science.gov (United States)

    2010-07-15

    ... bridges. The structural integrity of bridges that carry railroad tracks is important to the safety of... the structural failure of a railroad bridge. Train accidents caused by the structural failure of... inspection and analysis of the bridge. In general, timber bridges continue to function safely, and masonry...

  14. 33 CFR 115.40 - Bridge repairs.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Bridge repairs. 115.40 Section 115.40 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY BRIDGES BRIDGE LOCATIONS AND CLEARANCES; ADMINISTRATIVE PROCEDURES § 115.40 Bridge repairs. Repairs to a bridge which do...

  15. Modulating Arm Swing Symmetry with Cognitive Load: A Window on Rhythmic Spinal Locomotor Networks in Humans?

    Science.gov (United States)

    Killeen, Tim; Easthope, Christopher S; Filli, Linard; Linnebank, Michael; Curt, Armin; Bolliger, Marc; Zörner, Björn

    2017-05-15

    In healthy subjects, changes in arm swing symmetry while walking are observed when a cognitive dual task is added, with a tendency toward left-dominant arm swing as cognitive load increases. We applied a modified Stroop word/color naming paradigm to investigate this effect in spinal cord injured (SCI) patients. Six patients with cervical SCI (cSCI), 6 with thoracic injuries (tSCI; all 12 patients American Spinal Injury Association [ASIA] Injury Score [AIS]D), and 12 healthy, matched controls underwent three-dimensional 3D gait analysis while walking normally at a comfortable speed (NW) and when performing an additional congruent (CS) and incongruent (IS) Stroop task. An arm swing symmetry index (ASI)-in which positive values indicate proportionally more movement on the left and vice versa-was calculated. Even in the baseline NW condition, all three subject groups showed larger arm movements on the left. In controls, ASI increased (NW, 13.7 ± 6.3; CS, 16.6 ± 6.4; IS, 19.6 ± 7.8) as the task became more demanding. A larger shift in tSCI patients (NW, 15.8 ± 6.0; CS, 23.4 ± 3.8; IS, 30.7 ± 4.4) was driven by a significant reduction in right wrist trajectory (p = 0.014), whereas cSCI patients showed a small reduction in mean ASI with high variability (NW, 14.2 ± 10.7; CS, 9.3 ± 13.5; IS, 6.0 ± 12.9). The effect of the IS task on ASI compared to baseline (NW) was significantly different between tSCI (+12.5 ± 6.3) and cSCI (-8.2 ± 6.0) patients (p = 0.011). Disruption of the long propriospinal connections coordinating arm and leg movements during walking may explain the heightened sensitivity to manipulation of cognitive load in tSCI, whereas the more robust automaticity in cSCI may be attributed to impaired supraspinal inputs in the context of preserved intraspinal pathways.

  16. Comparative analysis of selected biomechanic characteristics between a support backward swing and support swing for the 1 1/4 straddle-piked forward salto on the parallel bars.

    Science.gov (United States)

    Kolar, Edvard; Kolar, Katarina Andlovic; Stuhec, Stanko

    2002-01-01

    The aim of our research was to study the relationships between performance variables in a support backward swing (SBS), which was used as a progressive step in the learning procedure for a 1 1/4 straddle-piked front somersault and the swing prior to a 1 1/4 straddle-piked front somersault from support to bent arm support on the parallel bars (5/4S). Mitja Petkovsek, parallel bars gold medallist at the 2000 EC in Bremen, performed these elements. Kinematic analysis involved CMAS software (Praha, 1993), and the Suskana body segment model that has 17 points and 15 segments. Kinetic variables were estimated using 2D IMGIM software, which has 8 points and 6 segments (Colja and Cuk, 1994). The results indicated that some kinematic aspects of the two types of swings were similar but there were important differences in kinetic aspects of the motion. During the swing for the 5/4S, force and torque were higher than in the SBS.

  17. Field performance of timber bridges. 7, Connell Lake stress-laminated deck bridge

    Science.gov (United States)

    L. E. Hislop; M. A. Ritter

    The Connell Lake bridge was constructed in early 1991 on the Tongass National Forest, Alaska, as a demonstration bridge under the Timber Bridge Initiative. The bridge is a stress-laminated deck structure with an approximate 36-ft length and 18-ft width and is the first known stress-laminated timber bridge constructed in Alaska. Performance of the bridge was monitored...

  18. 47 CFR 80.163 - Operator requirements of the Bridge-to-Bridge Act.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 5 2010-10-01 2010-10-01 false Operator requirements of the Bridge-to-Bridge... Requirements § 80.163 Operator requirements of the Bridge-to-Bridge Act. Each ship subject to the Bridge-to-Bridge Act must have on board a radio operator who holds a restricted radiotelephone operator permit or...

  19. Optimized Swinging Door Algorithm for Wind Power Ramp Event Detection: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Cui, Mingjian; Zhang, Jie; Florita, Anthony R.; Hodge, Bri-Mathias; Ke, Deping; Sun, Yuanzhang

    2015-08-06

    Significant wind power ramp events (WPREs) are those that influence the integration of wind power, and they are a concern to the continued reliable operation of the power grid. As wind power penetration has increased in recent years, so has the importance of wind power ramps. In this paper, an optimized swinging door algorithm (SDA) is developed to improve ramp detection performance. Wind power time series data are segmented by the original SDA, and then all significant ramps are detected and merged through a dynamic programming algorithm. An application of the optimized SDA is provided to ascertain the optimal parameter of the original SDA. Measured wind power data from the Electric Reliability Council of Texas (ERCOT) are used to evaluate the proposed optimized SDA.

  20. Comments on "cyclical swings" by Professor Hannah Decker: The underappreciated "solid center" of psychiatry.

    Science.gov (United States)

    Pies, Ronald W

    2016-02-01

    The history of psychiatry is characterized by some deep ideological and conceptual divisions, as adumbrated in Professor Hannah Decker's essay. However, the schism between "biological" and "psychosocial" models of mental illness and its treatment represents extreme positions among some psychiatrists-not the model propounded by academic psychiatry or its affiliated professional organizations. Indeed, the "biopsycho-social model" (BPSM) developed by Dr. George L. Engel has been, and remains, the foundational model for academic psychiatry, notwithstanding malign market forces that have undermined the BPSM's use in clinical practice. The BPSM is integrally related to "centralizing" and integrative trends in American psychiatry that may be traced to Franz Alexander, Karl Jaspers, and Engel himself, among others. This "Alexandrian-Jaspersian-Engelian" tradition is explored in relation to Professor Decker's "cyclical swing" model of psychiatry's history. (c) 2016 APA, all rights reserved).

  1. Swinging Atwood Machine: Experimental and numerical results, and a theoretical study

    Science.gov (United States)

    Pujol, O.; Pérez, J. P.; Ramis, J. P.; Simó, C.; Simon, S.; Weil, J. A.

    2010-06-01

    A Swinging Atwood Machine ( SAM) is built and some experimental results concerning its dynamic behaviour are presented. Experiments clearly show that pulleys play a role in the motion of the pendulum, since they can rotate and have non-negligible radii and masses. Equations of motion must therefore take into account the moment of inertia of the pulleys, as well as the winding of the rope around them. Their influence is compared to previous studies. A preliminary discussion of the role of dissipation is included. The theoretical behaviour of the system with pulleys is illustrated numerically, and the relevance of different parameters is highlighted. Finally, the integrability of the dynamic system is studied, the main result being that the machine with pulleys is non-integrable. The status of the results on integrability of the pulley-less machine is also recalled.

  2. Construction and measurements of an improved vacuum-swing-adsorption radon-mitigation system

    International Nuclear Information System (INIS)

    Street, J.; Bunker, R.; Dunagan, C.; Loose, X.; Schnee, R. W.; Stark, M.; Sundarnath, K.; Tronstad, D.

    2015-01-01

    In order to reduce backgrounds from radon-daughter plate-out onto detector surfaces, an ultra-low-radon cleanroom is being commissioned at the South Dakota School of Mines and Technology. An improved vacuum-swing-adsorption radon mitigation system and cleanroom build upon a previous design implemented at Syracuse University that achieved radon levels of ∼0.2 Bq m −3 . This improved system will employ a better pump and larger carbon beds feeding a redesigned cleanroom with an internal HVAC unit and aged water for humidification. With the rebuilt (original) radon mitigation system, the new low-radon cleanroom has already achieved a > 300× reduction from an input activity of 58.6 ± 0.7 Bq m −3 to a cleanroom activity of 0.13 ± 0.06 Bq m −3

  3. Construction and measurements of an improved vacuum-swing-adsorption radon-mitigation system

    Science.gov (United States)

    Street, J.; Bunker, R.; Dunagan, C.; Loose, X.; Schnee, R. W.; Stark, M.; Sundarnath, K.; Tronstad, D.

    2015-08-01

    In order to reduce backgrounds from radon-daughter plate-out onto detector surfaces, an ultra-low-radon cleanroom is being commissioned at the South Dakota School of Mines and Technology. An improved vacuum-swing-adsorption radon mitigation system and cleanroom build upon a previous design implemented at Syracuse University that achieved radon levels of ˜0.2 Bq m-3. This improved system will employ a better pump and larger carbon beds feeding a redesigned cleanroom with an internal HVAC unit and aged water for humidification. With the rebuilt (original) radon mitigation system, the new low-radon cleanroom has already achieved a > 300× reduction from an input activity of 58.6 ± 0.7 Bq m-3 to a cleanroom activity of 0.13 ± 0.06 Bq m-3.

  4. Construction and measurements of an improved vacuum-swing-adsorption radon-mitigation system

    Energy Technology Data Exchange (ETDEWEB)

    Street, J., E-mail: joseph.street@mines.sdsmt.edu; Bunker, R.; Dunagan, C.; Loose, X.; Schnee, R. W.; Stark, M.; Sundarnath, K.; Tronstad, D. [Department of Physics, South Dakota School of Mines & Technology, Rapid City, SD 57701 (United States)

    2015-08-17

    In order to reduce backgrounds from radon-daughter plate-out onto detector surfaces, an ultra-low-radon cleanroom is being commissioned at the South Dakota School of Mines and Technology. An improved vacuum-swing-adsorption radon mitigation system and cleanroom build upon a previous design implemented at Syracuse University that achieved radon levels of ∼0.2 Bq m{sup −3}. This improved system will employ a better pump and larger carbon beds feeding a redesigned cleanroom with an internal HVAC unit and aged water for humidification. With the rebuilt (original) radon mitigation system, the new low-radon cleanroom has already achieved a > 300× reduction from an input activity of 58.6 ± 0.7 Bq m{sup −3} to a cleanroom activity of 0.13 ± 0.06 Bq m{sup −3}.

  5. Selectivity of power system protections at power swings in power system

    Directory of Open Access Journals (Sweden)

    Jan Machowski

    2012-12-01

    Full Text Available The paper discusses out-of-step protection systems such as: generator pole slip protections, out of step tripping protections, distance protections of step-up transformer, distance protections of transmission lines and transformers, power swing blocking, and special out-of-step protection. It is shown that all these protections make up a protection system, to which a setting concept uniform for the entire power system has to be applied. If a power system is inappropriately equipped with these protections, or their settings are inappropriate, they may operate unselectively, thus contributing to the development of power system blackouts. In the paper the concepts for a real power system are given for the two stages: target stage fully compliant with selectivity criteria, and transitional stage between the current and target stages.

  6. CO2 Binding Organic Liquids Gas Capture with Polarity Swing Assisted Regeneration

    Energy Technology Data Exchange (ETDEWEB)

    Heldebrant, David [Battelle Memorial Institute, Columbus, OH (United States)

    2014-05-31

    This report outlines the comprehensive bench-scale testing of the CO2-binding organic liquids (CO2BOLs) solvent platform and its unique Polarity Swing Assisted Regeneration (PSAR). This study outlines all efforts on a candidate CO2BOL solvent molecule, including solvent synthesis, material characterization, preliminary toxicology studies, and measurement of all physical, thermodynamic and kinetic data, including bench-scale testing. Equilibrium and kinetic models and analysis were made using Aspen Plus™. Preliminary process configurations, a technoeconomic assessment and solvent performance projections for separating CO2 from a subcritical coal-fired power plant are compared to the U.S. Department of Energy's Case 10 monoethanolamine baseline.

  7. Rotation of the swing plane of Foucault's pendulum and Thomas spin precession: two sides of one coin

    International Nuclear Information System (INIS)

    Krivoruchenko, Mikhail I

    2009-01-01

    Using elementary geometric tools, we apply essentially the same methods to derive expressions for the rotation angle of the swing plane of Foucault's pendulum and the rotation angle of the spin of a relativistic particle moving in a circular orbit (the Thomas precession effect). (methodological notes)

  8. Rotation of the swing plane of Foucault's pendulum and Thomas spin precession: two sides of one coin

    Energy Technology Data Exchange (ETDEWEB)

    Krivoruchenko, Mikhail I [Alikhanov Institute for Theoretical and Experimental Physics, Russian Federation State Scientific Center, Moscow (Russian Federation)

    2009-08-31

    Using elementary geometric tools, we apply essentially the same methods to derive expressions for the rotation angle of the swing plane of Foucault's pendulum and the rotation angle of the spin of a relativistic particle moving in a circular orbit (the Thomas precession effect). (methodological notes)

  9. The effects of additional arm weights on arm-swing magnitude and gait patterns in Parkinson's disease.

    Science.gov (United States)

    Yoon, Jiyeon; Park, Jinse; Park, Kunbo; Jo, Geunyeol; Kim, Haeyu; Jang, Wooyoung; Kim, Ji Sun; Youn, Jinyoung; Oh, Eung Seok; Kim, Hee-Tae; Youm, Chang Hong

    2016-01-01

    Recently, arm facilitation has been interested in gait rehabilitation. However, there have been few studies concerning arm facilitation in patients with Parkinson's disease (PD). The aim of our study was to investigate the effect of increasing arm weights on gait pattern in patients with PD. Twenty-seven patients with PD were enrolled, and they underwent gait analysis using a three-dimensional motion capture system. Sandbags were applied to the distal forearms in all participants. We compared gait parameters including arm swing, pelvic motion, spatiotemporal data, and relative rotational angle between the weighted and unweighted gaits. The total arm-swing amplitude and pelvic rotation were significantly higher when walking with additional arm weights than without arm weights. Cadence, walking speed, stride length, and swing phase were significantly higher, whereas stride time, double-support time, and stance phase were significantly lower, when walking with additional arm weights than without arm weights. We conclude that adding weights to the arm during walking may facilitate arm and pelvic movements, which results in changes to gait patterns. The therapeutic use of additional arm weights could be considered for gait rehabilitation in PD to improve gait impairment. Arm-swing facilitation using weight load improved gait in Parkinson's disease. Copyright © 2015 International Federation of Clinical Neurophysiology. Published by Elsevier Ireland Ltd. All rights reserved.

  10. A Wireless Swing Angle Measurement Scheme Using Attitude Heading Reference System Sensing Units Based on Microelectromechanical Devices

    Directory of Open Access Journals (Sweden)

    Bingtuan Gao

    2014-11-01

    Full Text Available Feasible real-time swing angle measurement is significant to improve the efficiency and safety of industrial crane systems. This paper presents a wireless microelectromechanical system (MEMS-based swing angle measurement system. The system consists of two attitude heading reference system (AHRS sensing units with a wireless communication function, which are mounted on the hook (or payload and the jib (or base of the crane, respectively. With a combination of a three-axis accelerometer, a three-axis gyroscope and a three-axis magnetometer, the standard extended Kalman filter (EKF is used to estimate the desired orientation of the payload and the base. Wireless ZigBee communication is employed to transmit the orientation of the payload to the sensing unit mounted on the base, which measures the orientation of the base. Because several physical parameters from the payload to the base can be acquired from the original crane control system, the swing angles of the payload can be calculated based on the two measured orientation parameters together with the known physical parameters. Experiments were performed to show the feasibility and effectiveness of the proposed swing angle measurement system.

  11. Soleus stretch reflex inhibition in the early swing phase of gait using deep peroneal nerve stimulation in spastic stroke participants

    NARCIS (Netherlands)

    Voormolen, Marco M.; Ladouceur, Michel; Veltink, Petrus H.; Sinkjaer, Thomas

    2000-01-01

    Objectives: To investigate the feasibility of inhibiting the stretch reflex of the soleus muscle by a conditioning stimulus applied to the deep peroneal nerve in spastic stroke participants during the early swing phase of gait. - Materials and Methods: This study investigated the effect of an

  12. Using a Swinging Vane Anemometer to Measure Airflow. Module 14. Vocational Education Training in Environmental Health Sciences.

    Science.gov (United States)

    Consumer Dynamics Inc., Rockville, MD.

    This module, one of 25 on vocational education training for careers in environmental health occupations, contains self-instructional materials on using a swinging vane anemometer to measure airflow. Following guidelines for students and instructors and an introduction that explains what the student will learn are three lessons: (1) naming each…

  13. The development and validation of a golf swing and putt skill assessment for children.

    Science.gov (United States)

    Barnett, Lisa M; Hardy, Louise L; Brian, Ali S; Robertson, Sam

    2015-03-01

    The aim was to describe development of a process-oriented instrument designed to assess the golf swing and putt stroke, and to assess the instrument's discriminative validity in terms of age and reliability (intra-rater and re-test). A Delphi consultation (with golf industry professionals and researchers in movement skill assessment) was used to develop an assessment for each skill based on existing skill assessment protocols. Each skill had six components to be marked as present/absent. Individual scores were based on the number of performance components successfully demonstrated over two trials for each skill (potential score range 0 to 24). Children (n = 43) aged 6-10 years (M = 7.8 years, SD = 1.3) were assessed in both skills live in the field by one rater at Time 1(T1). A subset of children (n = 28) had consent for assessments to be videoed. Six weeks later 19 children were reassessed, five days apart (T2, T3). An ANOVA assessed discriminative validity i.e. whether skill competence at T1 differed by age (6 years, 7/8 years and 9/10 years). Intraclass correlations (ICC) assessed intra-rater reliability between the live and video assessment at T1 and test-retest reliability (between T2 and T3). Paired t-tests assessed any systematic differences between live and video assessments (T1) and between T2 and T3. Older children were more skilled (F (2, 40) = 11.18, p mastery level, and talent identification in beginner young golf players.Process rather than product oriented outcomes better identify areas of skill deficit in young children.The proposed swing and putt instrument can reliably identify skill deficits in children of elementary school age who are new to golf and can be used by a range of stakeholders including golf coaches, generalist sport coaches and physical education teachers.

  14. The effect of isolated core training on selected measures of golf swing performance.

    Science.gov (United States)

    Weston, Matthew; Coleman, Neil J; Spears, Iain R

    2013-12-01

    This study aimed to quantify the effect of an 8-wk isolated core training program on selected ball and club parameters during the golf swing and also the variability of these measures. Thirty-six club-level golfers were randomly assigned to an exercise (n = 18) or control (n =18) group. The exercise group participated in an 8-wk core training program, which included eight basic exercises. Both groups continued with their normal activity levels including golf. Baseline and postintervention measurements included club-head speed, backspin, sidespin, and timed core endurance. Baseline measures for club-head speed, backspin, sidespin, and core endurance test were 79.9 ± 8.4 mph, 3930 ± 780 rpm, 1410 ± 610 rpm, and 91 ± 56 s for the intervention group and 77.6 ± 8.8 mph, 3740 ± 910 rpm, 1290 ± 730 rpm, and 69 ± 55 s for the control group (mean ± SD). The effect of our core training, when compared with control, was a likely small improvement in club-head speed (3.6%; 90% confidence limits = ±2.7%) and a very likely small improvement in muscular endurance (61%; ±33%). The effect on backspin (5%; ±10%) and sidespin (-6%; ±20%) was unclear. Baseline variability for club-head speed, backspin, and sidespin (based on 10 swings per golfer) was 5.7% ± 5.3%, 43% ± 19%, and 140% ± 180% for the intervention group and 6.5% ± 5.3%, 53% ± 53%, and 170% ± 130% for control group. The effect of the intervention on within-subject variability was a moderate decrease for club-head speed, a small decrease for backspin, and a small increase for sidespin when compared with control. The benefits achieved from our isolated core training program are comparable with those from other studies.

  15. Developing deterioration models for Nebraska bridges.

    Science.gov (United States)

    2011-07-01

    Nebraska Bridge Management System (NBMS) was developed in 1999 to assist in optimizing budget allocation for : the maintenance, rehabilitation and replacement needs of highway bridges. This requires the prediction of bridge : deterioration to calcula...

  16. Faster bridge construction using precast substructures : brief.

    Science.gov (United States)

    2011-07-01

    Bridge replacement often requires road closures and detours that frustrate road users. It remains a key goal of Wisconsin DOT to reduce construction-related road use interruptions. This will be a challenge with bridges: Bridge inspections in 2007 ide...

  17. Key Royale bridge five year evaluation : [summary].

    Science.gov (United States)

    2013-06-01

    The Florida Department of Transportation (FDOT) : maintains more than 6,500 bridges. Considering : the expense of repair and replacement of bridges, : extending their durability and service life is : important. Of special concern for bridges in : mar...

  18. Monitoring bridge scour using fiber optic sensors.

    Science.gov (United States)

    2015-04-01

    The scouring process excavates and carries away materials from the bed and banks of streams, and from : around the piers and abutments of bridges. Scour undermines bridges and may cause bridge failures due to : structural instability. In the last 30 ...

  19. Lean Construction Applications for Bridge Inspection

    Science.gov (United States)

    2017-10-01

    Lean philosophy was used to analyze the efficiency of bridge inspection. Emphasis was put on identifying activities that add value to the final output, an owner approved bridge inspection report. 26 bridge inspections were shadowed. Time spent on bri...

  20. Continuous One-Arm Kettlebell Swing Training on Physiological Parameters in US Air Force Personnel: A Pilot Study.

    Science.gov (United States)

    Wade, Molly; O'Hara, Reginald; Caldwell, Lydia; Ordway, Jason; Bryant, Darryn

    The primary aim of this study was to investigate the effects of continuous one-arm kettlebell (KB) swing training on various US Air Force physical fitness testing components. Thirty trained male (n = 15) and female (n = 15) US Air Force (USAF) personnel volunteered and were sequentially assigned to one of three groups based on 1.5-mile run time: (1) KB one-arm swing training, (2) KB one-arm swing training plus highintensity running (KB + run), and (3) traditional USAF physical training (PT) according to Air Force Instruction 36-2905. The following measurements were made before and after 10 weeks of training: 1.5-mile run, 1-minute maximal push-ups, 1-minute maximal situps, maximal grip strength, pro agility, vertical jump, 40-yard dash, bodyweight, and percent body fat. Subjects attended three supervised exercise sessions per week for 10 weeks. During each exercise session, all groups performed a 10-minute dynamic warm-up followed by either (1) 10 minutes of continuous KB swings, (2) 10 minutes of continuous kettlebell swings plus 10 minutes of high-intensity running, or (3) 20 minutes of moderate intensity running plus push-ups and sit-ups. Average and peak heart rate were recorded for each subject after all sessions. Paired t tests were conducted to detect changes from pretesting to posttesting within each group and analysis of variance was used to compare between-group variability (ρ ≤ .05). Twenty subjects completed the study. There were no statistically significant changes in 1.5-mile run time between or within groups. The 40- yard dash significantly improved within the KB swing (ρ ≤ .05) and KB + run group (ρ ≤ .05); however, there were no significant differences in the traditional PT group (ρ ≤ .05) or between groups. Maximal push-ups significantly improved in the KB + run group (ρ ≤ .05) and trends toward significant improvements in maximal push-ups were found in both the KB (ρ = .057) and traditional PT (ρ = .067) groups. This study

  1. Comparison of lumbar and abdominal muscle activation during two types of golf swing: An EMG analysis. (Comparación de la activación muscular abdominal y lumbar en la realización de dos tipos de swing en Golf: Un análisis electromiográfico.

    Directory of Open Access Journals (Sweden)

    Sandhu Jaspal Singh

    2008-07-01

    Full Text Available AbstractGolf is a popular sport and golf swing is a complex movement which requires a coordinated sequence of muscle activity. Two types of golf swing exists i.e. “Classical” and “Modern”. Classical swing differs from modern swing in several respects, which are important when considering their effects on the lower back. The present study compared muscle activation amplitudes in the trunk region of golfers during two different types of golf swing. 22 golfers (21.5 years ±3.4 were instructed to perform modern and classical golf swing and surface EMG activity was recorded from external oblique (E.O., internal oblique (I.O., and erector spinae (E.S. muscles of both sides. Results showed muscle activity of right and left side of E.O. and I.O. to be lower in modern swing than classical swing (significant difference p menor que 0.05 in downswing and impact phase, whereas it is higher for both sides E.S. in modern swing. The E.S. muscle activity during follow-through phase was significantly higher (p menor que 0.05 in modern swing compared to classical swing. Significant differences in E.S. and other muscles activity suggest inappropriate recruitment of these muscles in golfers during the modern swing. EMG evidence proposes that the modern golf swing produces more extension forces in the lower back compared with the forces of classical swing.Resumen El Golf es un deporte popular y el swing en golf es un movimiento complejo que reclama una secuencia coordinada de movimientos. Existen dos tipos de swing: el clásico y el moderno. El Clásico se diferencia del Moderno en varios aspectos que son importantes cuando se consideran sus efectos en la parte inferior de la espalda. Este estudio comparó la amplitud de la activación muscular en el tronco de los golfistas al realizar los dos tipos de swing. Veintidos jugadores de golf (21.5 años ±3.4 fueron instruidos para realizar el swing moderno y clásico, tomándose la actividad muscular (actividad

  2. Steel-soil composite bridge

    DEFF Research Database (Denmark)

    Du, Guangli; Pettersson, Lars; Karoumi, Raid

    2017-01-01

    viability, while their environmental performance is overlooked. Today’s designers are urged to seek new design options to reduce the environmental burdens. Sweden owns more than 24574 bridges and most of them are short spans. Among them, the slab frame bridge (CFB) is a common solution. Soil steel composite...

  3. Crossing borders via mental bridges

    DEFF Research Database (Denmark)

    Keil, Dirk

    administration, and in specific on the attempt to initiate and promote cross-border regional integration via the building of mental bridges between Danish and German parts of the Femern Belt Region. Here one of the first projects aiming primarily at building mental bridges in the Femern Belt Region...

  4. The violin bridge as filter.

    Science.gov (United States)

    Bissinger, George

    2006-07-01

    The violin bridge filter role was investigated using modal and acoustic measurements on 12 quality-rated violins combined with systematic bridge rocking frequency f(rock) and wing mass decrements deltam on four bridges for two other violins. No isolated bridge resonances were observed; bridge motions were complex (including a "squat" mode near 0.8 kHz) except for low frequency rigid body pivot motions, all more or less resembling rocking motion at higher frequencies. A conspicuous broad peak near 2.3 kHz in bridge driving point mobility (labeled BH) was seen for good and bad violins. Similar structure was seen in averaged bridge, bridge feet, corpus mobilities and averaged radiativity. No correlation between violin quality and BH driving point, averaged corpus mobility magnitude, or radiativity was found. Increasing averaged-over-f(rock) deltam(g) from 0 to 0.12 generally increased radiativity across the spectrum. Decreasing averaged-over-deltam f(rock) from 3.6 to 2.6 kHz produced consistent decreases in radiativity between 3 and 4.2 kHz, but only few-percent decreases in BH frequency. The lowest f(rock) values were accompanied by significantly reduced radiation from the Helmholtz A0 mode near 280 Hz; this, combined with reduced high frequency output, created overall radiativity profiles quite similar to "bad" violins among the quality-rated violins.

  5. Fatigue tests on aluminium bridges

    NARCIS (Netherlands)

    Maljaars, J.; Soetens, F.; Straalen, IJ.J. van

    2004-01-01

    Traffic bridges are subjected to variable loads and should therefore be checked on fatigue. Especially low weight materials, like aluminium, are sensitive to fatigue, because the variable load is a substantial part of the total load. This paper shows the structural design of an aluminium bridge

  6. Contributions of knee swing initiation and ankle plantar flexion to the walking mechanics of amputees using a powered prosthesis.

    Science.gov (United States)

    Ingraham, Kimberly A; Fey, Nicholas P; Simon, Ann M; Hargrove, Levi J

    2014-01-01

    Recently developed powered prostheses are capable of producing near-physiological joint torque at the knee and/or ankle joints. Based on previous studies of biological joint impedance and the mechanics of able-bodied gait, an impedance-based controller has been developed for a powered knee and ankle prosthesis that integrates knee swing initiation and powered plantar flexion in late stance with increasing ankle stiffness throughout stance. In this study, five prosthesis configuration conditions were tested to investigate the individual contributions of each sub-strategy to the overall walking mechanics of four unilateral transfemoral amputees as they completed a clinical 10-m walk test using a powered knee and ankle prosthesis. The baseline condition featured constant ankle stiffness and no swing initiation or powered plantar flexion. The four remaining conditions featured knee swing initiation alone (SI) or in combination with powered plantar flexion (SI+PF), increasing ankle stiffness (SI+IK), or both (SI+PF+IK). Self-selected walking speed did not significantly change between conditions, although subjects tended to walk the slowest in the baseline condition compared to conditions with swing initiation. The addition of powered plantar flexion resulted in significantly higher ankle power generation in late stance irrespective of ankle stiffness. The inclusion of swing initiation resulted in a significantly more flexed knee at toe off and a significantly higher average extensor knee torque following toe off. Identifying individual contributions of intrinsic control strategies to prosthesis biomechanics could help inform the refinement of impedance-based prosthesis controllers and simplify future designs of prostheses and lower-limb assistive devices alike.

  7. Majorana entanglement bridge

    Science.gov (United States)

    Plugge, Stephan; Zazunov, Alex; Sodano, Pasquale; Egger, Reinhold

    2015-06-01

    We study the concurrence of entanglement between two quantum dots in contact to Majorana bound states on a floating superconducting island. The distance between the Majorana states, the charging energy of the island, and the average island charge are shown to be decisive parameters for the efficiency of entanglement generation. We find that long-range entanglement with basically distance-independent concurrence is possible over wide parameter regions, where the proposed setup realizes a "Majorana entanglement bridge." We also study the time-dependent concurrence obtained after one of the tunnel couplings is suddenly switched on, which reveals the time scales for generating entanglement. Accurate analytical expressions for the concurrence are derived both for the static and the time-dependent cases. Our results indicate that entanglement formation in interacting Majorana devices can be fully understood in terms of an interplay of elastic cotunneling (also referred to as "teleportation") and crossed Andreev reflection processes.

  8. Bridging the Evaluation Gap

    Directory of Open Access Journals (Sweden)

    Paul Wouters

    2017-02-01

    Full Text Available Paul Wouters’ essay is concerned with bridging the gap between what we value in our academic work and how we are assessed in formal evaluation exercises. He reflects on the recent evaluation of his own center, and reminds us that it is productive to see evaluations not as the (obviously impossible attempt to produce a true representation of past work, but rather as the exploration and performance of “who one wants to be.” Reflecting on why STS should do more than just play along to survive in the indicator game, he suggests that our field should contribute to changing its very rules. In this endeavor, the attitude and sensibilities developed in our field may be more important than any specific theoretical concepts or methodologies.

  9. Electrothermally Tunable Bridge Resonator

    KAUST Repository

    Hajjaj, Amal Z.

    2016-12-05

    This paper demonstrates experimentally, theoretically, and numerically a wide-range tunability of an in-plane clamped-clamped microbeam, bridge, and resonator compressed by a force due to electrothermal actuation. We demonstrate that a single resonator can be operated at a wide range of frequencies. The microbeam is actuated electrothermally, by passing a DC current through it. We show that when increasing the electrothermal voltage, the compressive stress inside the microbeam increases, which leads eventually to its buckling. Before buckling, the fundamental frequency decreases until it drops to very low values, almost to zero. After buckling, the fundamental frequency increases, which is shown to be as high as twice the original resonance frequency. Analytical results based on the Galerkin discretization of the Euler Bernoulli beam theory are generated and compared to the experimental data and to simulation results of a multi-physics finite-element model. A good agreement is found among all the results.

  10. Half Bridge Inductive Heater

    Directory of Open Access Journals (Sweden)

    Zoltán GERMÁN-SALLÓ

    2015-12-01

    Full Text Available Induction heating performs contactless, efficient and fast heating of conductive materials, therefore became one of the preferred heating procedure in industrial, domestic and medical applications. During induction heating the high-frequency alternating currents that heat the material are induced by means of electromagnetic induction. The material to be heated is placed inside the time-varying magnetic field generated by applying a highfrequency alternating current to an induction coil. The alternating electromagnetic field induces eddy currents in the workpiece, resulting resistive losses, which then heat the material. This paper describes the design of a power electronic converter circuit for induction heating equipment and presents the obtained results. The realized circuit is a low power half bridge resonant inverter which uses power MOS transistors and adequate driver circuits.

  11. Wright-Fisher diffusion bridges.

    Science.gov (United States)

    Griffiths, Robert C; Jenkins, Paul A; Spanò, Dario

    2017-10-06

    The trajectory of the frequency of an allele which begins at x at time 0 and is known to have frequency z at time T can be modelled by the bridge process of the Wright-Fisher diffusion. Bridges when x=z=0 are particularly interesting because they model the trajectory of the frequency of an allele which appears at a time, then is lost by random drift or mutation after a time T. The coalescent genealogy back in time of a population in a neutral Wright-Fisher diffusion process is well understood. In this paper we obtain a new interpretation of the coalescent genealogy of the population in a bridge from a time t∈(0,T). In a bridge with allele frequencies of 0 at times 0 and T the coalescence structure is that the population coalesces in two directions from t to 0 and t to T such that there is just one lineage of the allele under consideration at times 0 and T. The genealogy in Wright-Fisher diffusion bridges with selection is more complex than in the neutral model, but still with the property of the population branching and coalescing in two directions from time t∈(0,T). The density of the frequency of an allele at time t is expressed in a way that shows coalescence in the two directions. A new algorithm for exact simulation of a neutral Wright-Fisher bridge is derived. This follows from knowing the density of the frequency in a bridge and exact simulation from the Wright-Fisher diffusion. The genealogy of the neutral Wright-Fisher bridge is also modelled by branching Pólya urns, extending a representation in a Wright-Fisher diffusion. This is a new very interesting representation that relates Wright-Fisher bridges to classical urn models in a Bayesian setting. Copyright © 2017 Elsevier Inc. All rights reserved.

  12. Compilation of accelerated bridge construction (ABC) bridges : final report.

    Science.gov (United States)

    2016-01-01

    Development of accelerated bridge construction (ABC) technologies has been occurring across the country, many times in : isolation. Although FHWA and others have worked to facilitate communication between these efforts, there was not a : comprehensiv...

  13. Bridge Creek IMW database - Bridge Creek Restoration and Monitoring Project

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The incised and degraded habitat of Bridge Creek is thought to be limiting a population of ESA-listed steelhead (Oncorhynchus mykiss). A logical restoration approach...

  14. Reliability Assessment of Concrete Bridges

    DEFF Research Database (Denmark)

    Thoft-Christensen, Palle; Middleton, C. R.

    This paper is partly based on research performed for the Highways Agency, London, UK under the project DPU/9/44 "Revision of Bridge Assessment Rules Based on Whole Life Performance: concrete bridges". It contains the details of a methodology which can be used to generate Whole Life (WL) reliability...... profiles. These WL reliability profiles may be used to establish revised rules for concrete bridges. This paper is to some extend based on Thoft-Christensen et. al. [1996], Thoft-Christensen [1996] et. al. and Thoft-Christensen [1996]....

  15. Vulnerability of bridges to fire

    DEFF Research Database (Denmark)

    Giuliani, Luisa; Crosti, C.; Gentili, F.

    2012-01-01

    Even if recent effort in developing methodology and measures for design structures against fire and explosions has been mostly focused on buildings, bridges can also be very sensitive to those actions, as witnesses by some recent bridge accidents, which caused major economic losses and also......, considering both the costs deriving by structural damages and by limited serviceability and other indirect societal aspects. Few cases of recent bridge fire are reviewed in detail and structural consequences are highlighted, distinguishing between damages directly induced by fire and damages induced by local...

  16. Propiedades psicométricas de la versión Española del cuestionario de interacción trabajo-familia (SWING) [Psychometric properties of the Spanish version of the Survey Work-Home Interaction Nijmegen (SWING)

    NARCIS (Netherlands)

    Moreno-Jiménez, B.; Sanz Vergel, A.I.; Rodriguez Muñoz, A.; Geurts, S.A.E.

    2009-01-01

    Psychometric properties of the Spanish version of the Survey Work-Home Interaction Nijmegen (SWING). The aim of this work was to analyze the psychometric properties of the Spanish version of the «Survey Work-Home Interaction Nijmegen» (SWING) developed by S. Geurts and colleagues to evaluate the

  17. Effects of Electrolyte on Floating Water Bridge

    Directory of Open Access Journals (Sweden)

    Hideo Nishiumi

    2009-01-01

    spontaneously. In this paper, we examined flow direction of water bridge and what effects the addition of electrolytes such as NaCl, NaOH, and NH4Cl to the floating water bridge would give. We found that ionization degree reduced the length of water bridge though insoluble electrolyte Al2O3 had no effect on the length of water bridge.

  18. The stories of two bridges in Ghana

    DEFF Research Database (Denmark)

    Andreasen, Jørgen

    2004-01-01

    Public participation in bridge building was promoted by un habitat in the village of Mankrong. The neighbouring village did not participate in the construction of their bridge. The first flooding washed the second bridge down while the "participative bridge" stood up....

  19. Caltrans bridge inspection aerial robot.

    Science.gov (United States)

    2008-10-01

    The California Department of Transportation (Caltrans) project resulted in the development of a twin-motor, : single duct, electric-powered Aerobot designed of carrying video cameras up to 200 feet in elevation to enable : close inspection of bridges...

  20. Energy harvesting on highway bridges.

    Science.gov (United States)

    2011-01-01

    A concept for harvesting energy from the traffic-induced loadings on a highway bridge using piezoelectric : materials to generate electricity was explored through the prototype stage. A total of sixteen lead-zirconate : titanate (PZT) Type 5A piezoel...

  1. Preventative maintenance program for bridges.

    Science.gov (United States)

    2015-07-01

    The Kentucky Transportation Cabinets (KYTC) bridge inventory is rapidly aging. As such, the Cabinet : needs to identify and implement relevant preventative maintenance (PM) actions to extend the useful : service lives of those structures. Maintena...

  2. Research notes : listening to bridges.

    Science.gov (United States)

    2008-09-01

    The Federal Highway Administration requires owners of structurally deficient bridges to repair, replace, restrict truck loads, or conduct analysis and testing to maintain a safe highway system. Past experiments on reinforced concrete beams showed aco...

  3. Corrosion inhibitors for concrete bridges.

    Science.gov (United States)

    2004-12-01

    Deicing salts and salt-water spray can cause serious corrosion problems for reinforced concrete bridge structures. : These problems can lead to costly and labor-intensive repair and even replacement of the structure. Surface applied : corrosion inhib...

  4. Linear Cracking in Bridge Decks

    Science.gov (United States)

    2018-03-01

    Concrete cracking in bridge decks remains an important issue relative to deck durability. Cracks can allow increased penetration of chlorides, which can result in premature corrosion of the reinforcing steel and subsequent spalling of the concrete de...

  5. Interstate-35 bridge instrumentation renaissance.

    Science.gov (United States)

    2012-09-01

    An updated, accelerometer-based, sensor and data acquisition system was installed and verified on the I-35 Walnut Creek Bridge in Purcell, Oklahoma. The data collection system also includes a microwave communication system to move sensor and video da...

  6. 77 FR 53251 - Annual Materials Report on New Bridge Construction and Bridge Rehabilitation

    Science.gov (United States)

    2012-08-31

    ... describing construction materials used in new Federal-aid bridge construction and bridge rehabilitation... construction materials used in new bridge construction and bridge rehabilitation projects. Data on Federal-aid... the following tables: Construction Materials for New and Replaced Bridges, a summary report which...

  7. Combined use of maxillomandibular swing approach and neurosurgical ultrasonic aspirator in the management of extensive clival chordoma: A case report

    Directory of Open Access Journals (Sweden)

    Hassan Shahid

    2008-02-01

    Full Text Available Abstract Introduction Chordoma is a rare malignant tumour with an incidence of metastasis of less than 10 percent. Usually arising from clivus its posterior extension may involve the brainstem before presenting as nasal mass and obstruction. Surgery is the main mode of treatment with adjuvant radiotherapy. However surgery is rarely possible for a large intracranial lesion. Case presentation We report the case of an adolescent patient with a chordoma extending posteriorly to the brainstem and anteriorly to the nasopharynx and managed by the combination of resection using a maxillomandibular swing approach and the use of a neurosurgical ultrasonic aspirator. Conclusion Maxillomandibular swing approach provides good access for large nasopharyngeal tumour extending brainstem area.

  8. Testing hypotheses in an I(2) model with applications to the persistent long swings in the Dmk/$ rate

    DEFF Research Database (Denmark)

    Johansen, Søren; Juselius, Katarina; Frydman, Roman

    components in the I(2) model is discussed at some length. Model specification and tests are illustrated with an empirical analysis of long and persistent swings in the foreign exchange market between Germany and USA. The data analyzed consist of nominal exchange rates, relative prices, US inflation rate, two...... in nominal exchange rates, typical in periods of floating exchange rates....... long-term interest rates and two short-term interest rates over the 1975-1999 period. One important aim of the paper is to demonstrate that by structuring the data with the help of the I(2) model one can achieve a better understanding of the empirical regularities underlying the persistent swings...

  9. Subthreshold Current and Swing Modeling of Gate Underlap DG MOSFETs with a Source/Drain Lateral Gaussian Doping Profile

    Science.gov (United States)

    Singh, Kunal; Kumar, Sanjay; Goel, Ekta; Singh, Balraj; Kumar, Mirgender; Dubey, Sarvesh; Jit, Satyabrata

    2017-01-01

    This paper proposes a new model for the subthreshold current and swing of the short-channel symmetric underlap ultrathin double gate metal oxide field effect transistors with a source/drain lateral Gaussian doping profile. The channel potential model already reported earlier has been utilized to formulate the closed form expression for the subthreshold current and swing of the device. The effects of the lateral straggle and geometrical parameters such as the channel length, channel thickness, and oxide thickness on the off current and subthreshold slope have been demonstrated. The devices with source/drain lateral Gaussian doping profiles in the underlap structure are observed to be highly resistant to short channel effects while improving the current drive. The proposed model is validated by comparing the results with the numerical simulation data obtained by using the commercially available ATLAS™, a two-dimensional (2-D) device simulator from SILVACO.

  10. THE SWINGS OF SELENDANGIN RONGGENG DUKUH PARUK AND THE DANCER SCRUTINIZED THROUGH DECONSTRUCTION

    Directory of Open Access Journals (Sweden)

    Suzana Maria L.A. Fajarini

    2017-04-01

    Full Text Available Known as an adornment and beautification for womenin dancing costume, a scarf (selendang – Javanese/Indonesian in RonggengDukuhParuk and The Dancer has two contradictory meanings. On the one hand, it represents the shackle of the dancer, Srintil. On the other hand, the scarf can be a symbol of Srintil‘s dominance againstthe patriarchal system. As far as patriarchal society is concerned, subjugation towards women tends to occur. Believed to be born as a ronggeng dancer, Srintilgoes through oppressions since her early adolescent. However, employing Derrida‘s deconstruction theory, this paper will argue that Srintil attempts veryhard to achieve her liberation and to overturn the control. The swings of the scarf during the dancing denote the domination of the dancer‘s fated life and her self-determination as a woman. Under a strong influence of Javanese female negotiation, Srintil endeavors to liberate herself – although she is rendered to be unsuccessful – yet, there are some efforts done by her. Through some discussionthe readers are supposed to observe that Srintil– who is treated unjustly by patriarchal society– manipulativelyresists and fights for her freedom.

  11. Microtiming in Swing and Funk affects the body movement behavior of music expert listeners

    Science.gov (United States)

    Kilchenmann, Lorenz; Senn, Olivier

    2015-01-01

    The theory of Participatory Discrepancies (or PDs) claims that minute temporal asynchronies (microtiming) in music performance are crucial for prompting bodily entrainment in listeners, which is a fundamental effect of the “groove” experience. Previous research has failed to find evidence to support this theory. The present study tested the influence of varying PD magnitudes on the beat-related body movement behavior of music listeners. 160 participants (79 music experts, 81 non-experts) listened to 12 music clips in either Funk or Swing style. These stimuli were based on two audio recordings (one in each style) of expert drum and bass duo performances. In one series of six clips, the PDs were downscaled from their originally performed magnitude to complete quantization in steps of 20%. In another series of six clips, the PDs were upscaled from their original magnitude to double magnitude in steps of 20%. The intensity of the listeners' beat-related head movement was measured using video-based motion capture technology and Fourier analysis. A mixed-design Four-Factor ANOVA showed that the PD manipulations had a significant effect on the expert listeners' entrainment behavior. The experts moved more when listening to stimuli with PDs that were downscaled by 60% compared to completely quantized stimuli. This finding offers partial support for PD theory: PDs of a certain magnitude do augment entrainment in listeners. But the effect was found to be small to moderately sized, and it affected music expert listeners only. PMID:26347694

  12. A Robust Metal-Organic Framework for Dynamic Light-Induced Swing Adsorption of Carbon Dioxide.

    Science.gov (United States)

    Li, Haiqing; Martinez, Marta Rubio; Perry, Zachary; Zhou, Hong-Cai; Falcaro, Paolo; Doblin, Christian; Lim, Seng; Hill, Anita J; Halstead, Barry; Hill, Matthew R

    2016-08-01

    Adsorbents for CO2 capture need to demonstrate efficient release. Light-induced swing adsorption (LISA) is an attractive new method to release captured CO2 that utilizes solar energy rather than electricity. MOFs, which can be tailored for use in LISA owing to their chemical functionality, are often unstable in moist atmospheres, precluding their use. A MOF is used that can release large quantities of CO2 via LISA and is resistant to moisture across a large pH range. PCN-250 undergoes LISA, with UV flux regulating the CO2 desorption capacity. Furthermore, under UV light, the azo residues within PCN-250 have constrained, local, structural flexibility. This is dynamic, rapidly switching back to the native state. Reusability tests demonstrate a 7.3 % and 4.9 % loss in both adsorption and LISA capacity after exposure to water for five cycles. These minimal changes confirm the structural robustness of PCN-250 and its great potential for triggered release applications. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  13. Analysis of Pelvis-Thorax Coordination Patterns of Professional and Amateur Golfers during Golf Swing.

    Science.gov (United States)

    Sim, Taeyong; Yoo, Hakje; Choi, Ahnryul; Lee, Ki Young; Choi, Mun-Taek; Lee, Soeun; Mun, Joung Hwan

    2017-01-01

    The aim of this research was to quantify the coordination pattern between thorax and pelvis during a golf swing. The coordination patterns were calculated using vector coding technique, which had been applied to quantify the coordination changes in coupling angle (γ) between two different segments. For this, fifteen professional and fifteen amateur golfers who had no significant history of musculoskeletal injuries. There was no significant difference in coordination patterns between the two groups for rotation motion during backswing (p = 0.333). On the other hand, during the downswing phase, there were significant differences between professional and amateur groups in all motions (flexion/extension: professional [γ] = 187.8°, amateur [γ] = 167.4°; side bending: professional [γ] = 288.4°, amateur [γ] = 245.7°; rotation: professional [γ] = 232.0°, amateur [γ] = 229.5°). These results are expected to be a discriminating measure to assess complex coordination of golfers' trunk movements and preliminary study for interesting comparison by golf skilled levels.

  14. Rapid inversion: running animals and robots swing like a pendulum under ledges.

    Directory of Open Access Journals (Sweden)

    Jean-Michel Mongeau

    Full Text Available Escaping from predators often demands that animals rapidly negotiate complex environments. The smallest animals attain relatively fast speeds with high frequency leg cycling, wing flapping or body undulations, but absolute speeds are slow compared to larger animals. Instead, small animals benefit from the advantages of enhanced maneuverability in part due to scaling. Here, we report a novel behavior in small, legged runners that may facilitate their escape by disappearance from predators. We video recorded cockroaches and geckos rapidly running up an incline toward a ledge, digitized their motion and created a simple model to generalize the behavior. Both species ran rapidly at 12-15 body lengths-per-second toward the ledge without braking, dove off the ledge, attached their feet by claws like a grappling hook, and used a pendulum-like motion that can exceed one meter-per-second to swing around to an inverted position under the ledge, out of sight. We discovered geckos in Southeast Asia can execute this escape behavior in the field. Quantification of these acrobatic behaviors provides biological inspiration toward the design of small, highly mobile search-and-rescue robots that can assist us during natural and human-made disasters. We report the first steps toward this new capability in a small, hexapedal robot.

  15. The effect of expert performance microtiming on listeners’ experience of groove in swing or funk music

    Directory of Open Access Journals (Sweden)

    Olivier Senn

    2016-10-01

    Full Text Available This study tested the influence of expert performance microtiming on listeners' groove experience. Two professional rhythm section (bass/drums performances in swing and funk style were recorded, and the performances' original microtemporal deviations from a regular metronomic grid were scaled to several magnitude levels. Music expert (n=79 and non-expert (n=81 listeners rated the groove qualities of stimuli using a newly developed questionnaire that measures three dimensions of the groove experience (Entrainment, Enjoyment, and the absence of Irritation. Findings show that music expert listeners were more sensitive to microtiming manipulations than non-experts. Across both expertise groups and for both styles, groove ratings were high for microtiming magnitudes equal or smaller than those originally performed and decreased for exaggerated microtiming magnitudes. In particular, both the fully quantized music and the music with the originally performed microtiming pattern were rated equally high on groove. This means that neither the claims of PD theory (that microtiming deviations are necessary for groove nor the opposing exactitude hypothesis (that microtiming deviations are detrimental to groove were supported by the data.

  16. ON MEASURING AMPLITUDES AND PERIODS OF PHYSICAL PENDULUM MICRO-SWINGS WITH ROLLING-CONTACT BEARING

    Directory of Open Access Journals (Sweden)

    N. N. Riznookaya

    2011-01-01

    Full Text Available The paper considers a method and an instrument for measuring amplitudes and  periods of physical pendulum oscillations with rolling-contact bearing in the regime of micro-swings when the oscillation amplitude is significantly less of an elastic contact angle. It has been established that the main factors limiting a measuring accuracy are noises of the measuring circuit, base vibration and analog-digital conversion. A new measuring methodology based on original algorithms of data processing and application of the well-known methods for statistic processing of a measuring signal is  proposed in the paper. The paper contains error estimations for measuring oscillation amplitudes justified by discreteness of a signal conversion in a photoelectric receptor and also by the influence of measuring circuit noise. The paper reveals that the applied methodologies make it possible to ensure measuring of amplitudes with an error of 0.2 second of arc and measuring of a period with an error of 10–4 s. The original measuring instrument including mechanical and optical devices and also an electric circuit of optical-to-electrical measuring signal conversion is described in the paper. 

  17. Systemic swings in end-Permian environments from Siberian Traps carbon and sulfur outgassing

    Science.gov (United States)

    Black, B. A.; Neely, R.; Lamarque, J. F.; Elkins-Tanton, L. T.; Kiehl, J. T.; Shields, C. A.; Mills, M. J.; Bardeen, C.

    2017-12-01

    U-Pb geochronology has revealed that Siberian Traps flood basalt magmatism coincided with the 252 Ma end-Permian mass extinction. Most environmental consequences of magmatism follow directly or indirectly from the release of sulfur and some combination of magmatic and metamorphic carbon to the atmosphere (exceptions include ozone depletion from halogen emissions, release of toxic metals, and enhanced weathering of fresh volcanic rocks). However, the critical combinations of forcing and stress that trigger global mass extinction remain unknown. In particular, the combined and competing effects of sulfur and carbon outgassing on Earth systems remain to be quantified. Here we present results from global climate model simulations of flood basalt outgassing that account for sulfur chemistry and aerosol microphysics. We consider the effects of sulfur and carbon in isolation and in tandem, and find that carbon and sulfur emissions combine to generate swings in climate, ocean circulation, and hydrology. Our simulations provide a self-consistent framework to quantitatively explain observed features of the end-Permian including surface warming, fluctuating ocean oxygenation, intense weathering, and carbon cycle perturbation, unifying observed changes in climate and geochemical cycles with feedbacks initiated by Siberian Traps magmatism.

  18. Development of a novel pressure swing adsorption dehydration system for the preservation of dermal tissue

    International Nuclear Information System (INIS)

    Chou, S.K.; Chua, K.J.; Teoh, S.H.; Lim, K.K.; Sun, W.Q.

    2007-01-01

    Due to the perishable nature of bioproducts, the need to preserve them until required is of paramount importance. This is particularly true for tissue engineered products such as the skin. The paper reports on a novel drying technology, Pressure Swing Adsorption Dehydration System (PSAD), for the dehydration of freshly prepared acellular porcine dermal tissue. The aim is to investigate the effectiveness of the PSADS to obtain partially dehydrated mammalian dermal tissue suitable for biomedical preservation. Experiments were carried out by a varying number of parameters such as the chamber pressure level, duration and temperature. Samples were weighed and the surface color was taken periodically to track moisture removal rate and color deterioration due to oxidation. Scanning electron microscopy images of the lyophilized and processed samples were also taken for comparison. Results indicated that the depressurized level, frequency of pressure drops and temperature have positive effects on dehydration rate. Color change was generally low, indicating low level of oxidation. Hence, the PSADS provides a feasible way that can be as good if not better than current drying processes to obtain partially dried dermal tissue while minimizing product deterioration

  19. Enhancing analog performance and suppression of subthreshold swing using hetero-junctionless double gate TFETs

    Science.gov (United States)

    Chauhan, Sudakar Singh; Sharma, Neha

    2017-12-01

    This paper proposes hetero-junctionless double gate tunnel field effect transistor (HJLDG-TFETs) for suppression of subthreshold swing (SS) using an InAs compound semiconductor material. The proposed device with high dielectric material, gives an excellent performance when InAs uses at source side. Because of low band gap of 0.36 eV , it reduces the potential barrier height of source channel interface causing higher band to band tunneling. Whereas, Si at the drain side with higher band gap of 1.12 eV , increasing the barrier height of drain channel interface causing lower quantum tunneling. As a result, the proposed device with high-k (HfO2) at 30 nm channel section provides a tremendous characteristics with high ION /IOFF ratio of 2 ×1011 , a point SS of 43.30 mV / decade and moderate SS of 56.75 mV / decade . All the above results show that the proposed device is assured for a low power switching application. The variation in gate supply voltage also analyzed for transconductance property of the device.

  20. Dynamic modeling and explicit/multi-parametric MPC control of pressure swing adsorption systems

    KAUST Repository

    Khajuria, Harish

    2011-01-01

    Pressure swing adsorption (PSA) is a flexible, albeit complex gas separation system. Due to its inherent nonlinear nature and discontinuous operation, the design of a model based PSA controller, especially with varying operating conditions, is a challenging task. This work focuses on the design of an explicit/multi-parametric model predictive controller for a PSA system. Based on a system involving four adsorbent beds separating 70% H2, 30% CH4 mixture into high purity hydrogen, the key controller objective is to fast track H2 purity to a set point value of 99.99%. To perform this task, a rigorous and systematic framework is employed. First, a high fidelity detailed dynamic model is built to represent the system\\'s real operation, and understand its dynamic behavior. The model is then used to derive appropriate linear models by applying suitable system identification techniques. For the reduced models, a model predictive control (MPC) step is formulated, where latest developments in multi-parametric programming and control are applied to derive a novel explicit MPC controller. To test the performance of the designed controller, closed loop simulations are performed where the dynamic model is used as the virtual plant. Comparison studies of the derived explicit MPC controller are also performed with conventional PID controllers. © 2010 Elsevier Ltd. All rights reserved.

  1. A study of the Armstrong Whitworth swing beam engine for automotive application

    Science.gov (United States)

    1983-01-01

    The introduction of ceramics to those parts suffering high thermal loading was successfully demonstrated, and there is no question that the 100 kw (134 hp) naturally aspirated engine of the future will be developed to produce up to 300 kw (402 hp) by the application of turbocharging or its equivalent. However, at the 60 - 80 kw (80 - 107 hp) size needed for the economic automotive engine, scaling down the 300 kw (402 hp) is beset by the laws of scale. The conventional four stroke diesel was not shown to be successful at the small high speed engine size. The opposed piston two stroke engine does not suffer the same laws of scale and engines in the low power range have already been marketed successfully. The half liter/cylinder Armstrong Whitworth Swing Beam Engine is the latest to be designed with the automotive market in mind. Its low noise structure and balanced linkage system coupled with advantages for easy start and potential use of low grade fuels, derived from its variable compression ratio and slow piston motion, qualifies it for the application.

  2. Rapid Inversion: Running Animals and Robots Swing like a Pendulum under Ledges

    Science.gov (United States)

    Mongeau, Jean-Michel; McRae, Brian; Jusufi, Ardian; Birkmeyer, Paul; Hoover, Aaron M.; Fearing, Ronald; Full, Robert J.

    2012-01-01

    Escaping from predators often demands that animals rapidly negotiate complex environments. The smallest animals attain relatively fast speeds with high frequency leg cycling, wing flapping or body undulations, but absolute speeds are slow compared to larger animals. Instead, small animals benefit from the advantages of enhanced maneuverability in part due to scaling. Here, we report a novel behavior in small, legged runners that may facilitate their escape by disappearance from predators. We video recorded cockroaches and geckos rapidly running up an incline toward a ledge, digitized their motion and created a simple model to generalize the behavior. Both species ran rapidly at 12–15 body lengths-per-second toward the ledge without braking, dove off the ledge, attached their feet by claws like a grappling hook, and used a pendulum-like motion that can exceed one meter-per-second to swing around to an inverted position under the ledge, out of sight. We discovered geckos in Southeast Asia can execute this escape behavior in the field. Quantification of these acrobatic behaviors provides biological inspiration toward the design of small, highly mobile search-and-rescue robots that can assist us during natural and human-made disasters. We report the first steps toward this new capability in a small, hexapedal robot. PMID:22701594

  3. Analysis of Dynamic Differential Swing Limited Logic for Low-Power Secure Applications

    Directory of Open Access Journals (Sweden)

    Denis Flandre

    2012-03-01

    Full Text Available Low-power secure applications such as Radio Frequency IDentification (RFID and smart cards represent extremely constrained environments in terms of power consumption and die area. This paper investigates the power, delay and security performances of the dynamic differential swing limited logic (DDSLL. A complete analysis of an advanced encryption standard (AES S-box is conducted using a low-power (LP 65 nm CMOS technology node. Measurements show that the DDSLL S-box has 35% less power consumption than the static CMOS S-box, with an area increase of only 12%, at the expense of a 2.5× increase in delay which remains fairly acceptable for low-power applications such as RFIDs and smart cards. Also when compared to other dynamic differential logic (DDL styles, simulation results show that DDSLL and dynamic current mode logic (DyCML consume the same power which is about 1.8× less that of sense amplifier based logic (SABL. The effect of process variations is also studied, measurement results show that the DDSLL style has lower variability in terms of dynamic power as the activity factor (αF is deterministic thanks to glitch-free operation. As for security, the perceived information metric demonstrates that the DDSLL S-box has a 3× security margin compared to static CMOS. Therefore, DDSLL presents an interesting tradeoff between improved security and area constrained low-power designs.

  4. Allocation of ESS by interval optimization method considering impact of ship swinging on hybrid PV/diesel ship power system

    International Nuclear Information System (INIS)

    Wen, Shuli; Lan, Hai; Hong, Ying-Yi; Yu, David C.; Zhang, Lijun; Cheng, Peng

    2016-01-01

    Highlights: • An uncertainty model of PV generation on board is developed based on the experiments. • The moving and swinging of the ship are considered in the optimal ESS sizing problem. • Optimal sizing of ESS in a hybrid PV/diesel/ESS ship power system is gained by the interval optimization method. • Different cases were studied to show the significance of the proposed method considering the swinging effects on the cost. - Abstract: Owing to low efficiency of traditional ships and the serious environmental pollution that they cause, the use of solar energy and an energy storage system (ESS) in a ship’s power system is increasingly attracting attention. However, the swinging of a ship raises crucial challenges in designing an optimal system for a large oil tanker ship, which are associated with uncertainties in solar energy. In this study, a series of experiments are performed to investigate the characteristics of a photovoltaic (PV) system on a moving ship. Based on the experimental results, an interval uncertainty model of on-board PV generation is established, which considers the effect of the swinging of the ship. Due to the power balance equations, the outputs of the diesel generator and the ESS on a large oil tanker are also modeled using interval variables. An interval optimization method is developed to determine the optimal size of the ESS in this hybrid ship power system to reduce the fuel cost, capital cost of the ESS, and emissions of greenhouse gases. Variations of the ship load are analyzed using a new method, taking five operating conditions into account. Several cases are compared in detail to demonstrate the effectiveness of the proposed algorithm.

  5. EMG Analysis and Sagittal Plane Kinematics of the Two-Handed and Single-Handed Kettlebell Swing: A Descriptive Study.

    Science.gov (United States)

    Van Gelder, Leonard H; Hoogenboom, Barbara J; Alonzo, Bryan; Briggs, Dayna; Hatzel, Brian

    2015-11-01

    Kettlebell (KB) swing exercises have been proposed as a possible method to improve hip and spinal motor control as well as improve power, strength, and endurance. To describe electromyographic (EMG) and sagittal plane kinematics during two KB exercises: the two-handed KB swing (THKS) and the single-handed KB swing (SHKS). In addition, the authors sought to investigate whether or not hip flexor length related to the muscular activity or the kinematics of the exercise. Twenty-three healthy college age subjects participated in this study. Demographic information and passive hip flexor length were recorded for each subject. A maximum voluntary isometric contraction (MVIC) of bilateral gluteus maximus (GMAX), gluteus medius (GMED), and biceps femoris (BF) muscles was recorded. EMG activity and sagittal plane video was recorded during both the THKS and SHKS in a randomized order. Normalized muscular activation of the three studied muscles was calculated from EMG data. During both SHKS and THKS, the average percent of peak MVIC for GMAX was 75.02% ± 55.38, GMED 55.47% ± 26.33, and BF 78.95% ± 53.29. Comparisons of the mean time to peak activation (TTP) for each muscle showed that the biceps femoris was the first muscle to activate during the swings. Statistically significant (p < .05), moderately positive correlations (r = .483 and .417) were found between passive hip flexor length and % MVIC for the GMax during the SHKS and THKS, respectively. The THKS and SHKS provide sufficient muscular recruitment for strengthening of all of the muscles explored. This is the first study to show significant correlations between passive hip flexor length and muscular activation of hip extensors, particularly the GMax. Finally, the BF consistently reached peak activity before the GMax and GMed during the SHKS. Level 3.

  6. Immediate Effects of Sports Taping Applied on the Lead Knee of Low- and High-Handicapped Golfers During Golf Swing.

    Science.gov (United States)

    Kim, Tae-Gyu; Kim, Eun-Kuk; Park, Jong-Chul

    2017-04-01

    Kim, T-G, Kim, E-K, and Park, J-C. Immediate effects of sports taping applied on the lead knee of low- and high-handicapped golfers during golf swing. J Strength Cond Res 31(4): 981-989, 2017-Elite golf athletes suffer from various musculoskeletal injuries due to repeated golf swings. Repetitive varus moment during golf swing has been suggested as a possible cause of injuries to the lead knee. The aim of this study was to objectively and quantitatively evaluate the immediate effects of sports taping on the lead knee of elite golfers to restrict varus moment. Thirty-one elite golfers were assigned to the low- (LHG, n = 15) or high-handicapped group (HHG, n = 16). Using 3-dimensional motion analysis, the lead knee position on the frontal plane with and without rigid taping (RT), elastic taping (ET), and placebo taping was identified in 4 separate phases by the 5 events of golf swing as follows: the peak of the backswing (E1), parallel to the ground during downswing (E2), ball impact (E3), parallel to the ground during follow-through (E4), and finish (E5). The LHG when using a driver club had decreased movement toward knee varus with RT and ET than that without it from E1 to E2 (p = 0.001). The LHG when using a 5-iron club decreased movement toward knee varus with RT than that without it from E1 to E2 (p = 0.006) and from E2 to E3 (p = 0.019). The HHG when using a driver club had decreased movement toward knee varus with RT from E1 to E2 (p = 0.014). Sports taping may be helpful for elite golfers in terms of reducing varus moment of the lead knee during the downswing and be useful for the development of preventive strategies for golf-related knee injuries.

  7. Dynamic model and workspace analysis of novel incompletely restrained cable-suspension swing system driven by two cables

    Directory of Open Access Journals (Sweden)

    Naige Wang

    2017-03-01

    Full Text Available The incompletely restrained cable-suspension swing system driven by two cables is introduced in this article. Based on wrench of forces theory and Lagrange’s equation of first kind, the static and dynamics models of incompletely restrained cable-suspension swing system driven by two cables are established, respectively. In order to obtain an intuitive understanding of the trajectory analysis, a dynamics model consisting of governing equation and geometric constraint conditions which is a set of the mixed differential-algebraic equation in mathematics is established. A typical feedback controller and an inverse model were set up to estimate the driving function. The effective workspace, which is used to guarantee an efficient swing process, mostly depends on the geometrical shape rather than the volume itself which was calculated by trajectory analysis. In order to estimate system features and ensure a limited range of tension in underconstrained spatial cable system, the probable location of unbalanced loading was evaluated by pointwise evaluation techniques during normal work.

  8. Influence on Strength and Flexibility of a Swing Phase-Specific Hamstring Eccentric Program in Sprinters' General Preparation.

    Science.gov (United States)

    Guex, Kenny J; Lugrin, Véronique; Borloz, Stéphane; Millet, Grégoire P

    2016-02-01

    Hamstring injuries are common in sprinters and mainly occur during the terminal swing phase. Eccentric training has been shown to reduce hamstring injury rate by improving several risk factors. The aim of this study was to test the hypothesis that an additional swing phase-specific hamstring eccentric training in well-trained sprinters performed at the commencement of the winter preparation is more efficient to improve strength, ratio, optimum angle, and flexibility than a similar program without hamstring eccentric exercises. Twenty sprinters were randomly allocated to an eccentric (n = 10) or a control group (n = 10). Both groups performed their usual track and field training throughout the study period. Sprinters in the eccentric group performed an additional 6-week hamstring eccentric program, which was specific to the swing phase of the running cycle (eccentric high-load open-chain kinetic movements covering the whole hamstring length-tension relationship preformed at slow to moderate velocity). Isokinetic and flexibility measurements were performed before and after the intervention. The eccentric group increased hamstring peak torques in concentric at 60° · s(-1) by 16% (p ratios by 12% (p hamstring peak torques only in eccentric at 30° · s(-1) by 6% (p ≤ 0.05) and at 120° · s(-1) by 6% (p hamstring eccentric training in sprinters seems to be crucial to address different risk factors for hamstring strain injuries, such as eccentric and concentric strength, hamstring-to-quadriceps ratio ratio, and flexibility.

  9. Analytical modeling of subthreshold current and subthreshold swing of Gaussian-doped strained-Si-on-insulator MOSFETs

    International Nuclear Information System (INIS)

    Rawat, Gopal; Kumar, Sanjay; Goel, Ekta; Kumar, Mirgender; Jit, S.; Dubey, Sarvesh

    2014-01-01

    This paper presents the analytical modeling of subthreshold current and subthreshold swing of short-channel fully-depleted (FD) strained-Si-on-insulator (SSOI) MOSFETs having vertical Gaussian-like doping profile in the channel. The subthreshold current and subthreshold swing have been derived using the parabolic approximation method. In addition to the effect of strain on silicon layer, various other device parameters such as channel length (L), gate-oxide thickness (t ox ), strained-Si channel thickness (t s-Si ), peak doping concentration (N P ), project range (R p ) and straggle (σ p ) of the Gaussian profile have been considered while predicting the device characteristics. The present work may help to overcome the degradation in subthreshold characteristics with strain engineering. These subthreshold current and swing models provide valuable information for strained-Si MOSFET design. Accuracy of the proposed models is verified using the commercially available ATLAS™, a two-dimensional (2D) device simulator from SILVACO. (semiconductor devices)

  10. Safety and walking ability of KAFO users with the C-Brace®Orthotronic Mobility System, a new microprocessor stance and swing control orthosis.

    Science.gov (United States)

    Pröbsting, Eva; Kannenberg, Andreas; Zacharias, Britta

    2017-02-01

    There are clear indications for benefits of stance control orthoses compared to locked knee ankle foot orthoses. However, stance control orthoses still have limited function compared with a sound human leg. The aim of this study was to evaluate the potential benefits of a microprocessor stance and swing control orthosis compared to stance control orthoses and locked knee ankle foot orthoses in activities of daily living. Survey of lower limb orthosis users before and after fitting of a microprocessor stance and swing control orthosis. Thirteen patients with various lower limb pareses completed a baseline survey for their current orthotic device (locked knee ankle foot orthosis or stance control orthosis) and a follow-up for the microprocessor stance and swing control orthosis with the Orthosis Evaluation Questionnaire, a new self-reported outcome measure devised by modifying the Prosthesis Evaluation Questionnaire for use in lower limb orthotics and the Activities of Daily Living Questionnaire. The Orthosis Evaluation Questionnaire results demonstrated significant improvements by microprocessor stance and swing control orthosis use in the total score and the domains of ambulation ( p = .001), paretic limb health ( p = .04), sounds ( p = .02), and well-being ( p = .01). Activities of Daily Living Questionnaire results showed significant improvements with the microprocessor stance and swing control orthosis with regard to perceived safety and difficulty of activities of daily living. The microprocessor stance and swing control orthosis may facilitate an easier, more physiological, and safer execution of many activities of daily living compared to traditional leg orthosis technologies. Clinical relevance This study compared patient-reported outcomes of a microprocessor stance and swing control orthosis (C-Brace) to those with traditional knee ankle foot orthosis and stance control orthosis devices. The C-Brace offers new functions including controlled

  11. Dynamic assessment of bridge deck performance considering realistic bridge-traffic interaction

    Science.gov (United States)

    2017-09-01

    Concrete bridge decks are directly exposed to daily traffic loads and may experience some surface cracking caused by excessive stress or fatigue accumulation, which requires repair or replacement. Among typical bridges in North America, bridge decks ...

  12. 33 CFR 118.100 - Retroreflective panels on bridge piers.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Retroreflective panels on bridge... SECURITY BRIDGES BRIDGE LIGHTING AND OTHER SIGNALS § 118.100 Retroreflective panels on bridge piers. The... 12 inches square. (c) To mark bridge piers or channel sides on bridges not required to have bridge...

  13. Is there really an eccentric action of the hamstrings during the swing phase of high-speed running? part I: A critical review of the literature.

    Science.gov (United States)

    Van Hooren, Bas; Bosch, Frans

    2017-12-01

    It is widely assumed that there is an eccentric hamstring muscle fibre action during the swing phase of high-speed running. However, animal and modelling studies in humans show that the increasing distance between musculotendinous attachment points during forward swing is primarily due to passive lengthening associated with the take-up of muscle slack. Later in the swing phase, the contractile element (CE) maintains a near isometric action while the series elastic (tendinous) element first stretches as the knee extends, and then recoils causing the swing leg to forcefully retract prior to ground contact. Although modelling studies showed some active lengthening of the contractile (muscular) element during the mid-swing phase of high-speed running, we argue that the increasing distance between the attachment points should not be interpreted as an eccentric action of the CE due to the effects of muscle slack. Therefore, there may actually be no significant eccentric, but rather predominantly an isometric action of the hamstrings CE during the swing phase of high-speed running when the attachment points of the hamstrings are moving apart. Based on this, we propose that isometric rather than eccentric exercises are a more specific way of conditioning the hamstrings for high-speed running.

  14. Numerical simulations of constant cycle jets from a swing nozzle; Kubirufi undo suru fukidashiguchi yori funshutsu sareru funryu no suchi kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Ueda, T.; Shibano, T. [Shinryo Corp., Tokyo (Japan); Hagino, G.; Honda, N.; Suzuki, M. [University of Electro-Communications, Tokyo (Japan)

    1997-09-25

    To apply swing nozzles to HVAC (heating, ventilation and air conditioning) systems in large indoor spaces, numerical simulations were conducted for the characteristics of constant cycle jets from a swing nozzle. For the simulations, the velocity and temperature of air supply, and the inclination angle and swing cycle of outlet were used as parameters. A total of 168 numerical simulations were conducted, which included cases with fixed air supply direction. As a result, jet formations could be classified into four groups. Among these, two groups provided distributions with depressions in their centers, which means that the residual air flow velocity in the dwelling region should be carefully examined. Characteristics of cycle jets greatly varied dependent on the parameters. Especially, the vertical distance from the outlet and the diffusion width of swing direction increased or decreased monotonously against the variation of parameters, except only a part of cases. For the change of air flow velocity at the fixed point, its amplitude became shorter with shortening the swing frequency. The frequency was not always in agreement with the movement of the nozzle. Complicated behavior of air flow velocity was observed dependent on the swing frequency. 10 refs., 12 figs., 2 tabs.

  15. The Akashi Kaikyo Bridge and the Storebælt Bridge

    DEFF Research Database (Denmark)

    Gimsing, Niels Jørgen

    1999-01-01

    With the completion of the Akashi Kaikyo Bridge and the Storebælt East Bridge the development of the suspension bridge technology in the 20th century has manifested itself in two impressive structures. With the present echnology may bridges of similar (and also more modest) dimensions...... will undoubtedly be built far into the next century. For bridges going beyond the spans of existing bridges it is, however, likely that new concepts will be developed....

  16. Floating liquid bridge charge dynamics

    Science.gov (United States)

    Teschke, Omar; Soares, David Mendez; Gomes, Whyllerson Evaristo; Valente Filho, Juracyr Ferraz

    2016-01-01

    The interaction of liquid with electric fields is investigated in a configuration where up to 13 kV are applied between electrodes resulting in a 106 V/m electric field in the capillaries and where there is the formation of a free-standing fluid bridge in the interelectrode gap. The Mott-Gurney equation was fitted to the measured ionization current vs applied voltage curve which indicates that the ionization rate at the high-voltage anode electrode dimethylsulfoxide (DMSO) interface and space charging in the interelectrode gap determine the floating liquid bridge current for a given cathode-to-anode voltage. Space charge effects were measured in the cathode becker and also at the liquid bridge since the ionized charges at the anode migrate to the bridge outer surface and decrease the interfacial tension from 43 mJ/m2 to 29 mJ/m2. Two distinct structural regions then form the bridge, a charged plastic (bulk modulus ˜100 MPa) conducting outer layer with a surface conductivity of ˜10-9 Ω-1, which shapes and supports the floating fluid structure, and an inner liquid cylinder, where DMSO molecules flow.

  17. Thermal bridges of modern windows

    DEFF Research Database (Denmark)

    Hansen, Ernst Jan de Place; Møller, Eva B.; Nielsen, Anker

    2013-01-01

    With its focus on reduced energy consumption, contemporary housing construction requires a highly insulated and airtight building envelope with as few thermal bridges as possible.Windows must be carefully designed, as thermal bridges can lead to surface condensation or mold growth, even if the wi......With its focus on reduced energy consumption, contemporary housing construction requires a highly insulated and airtight building envelope with as few thermal bridges as possible.Windows must be carefully designed, as thermal bridges can lead to surface condensation or mold growth, even...... if the window has an U-factor of 1 W/(m2·K) or lower. This paper describes the development of modern, energy efficient Danish windows with reduced thermal bridges. It focuses on materials, geometry, and sealing of window panes based on a literature review. Examples of modern windows are presented. Experience...... been an important driver for the development of new window solutions in Denmark, increasing the inner-surface temperature at the sealing of window panes. However, it will not stop complaints fromconsumers, as this temperature is calculated under standardized conditions. Increasing requirements...

  18. A tutorial on bridge sampling.

    Science.gov (United States)

    Gronau, Quentin F; Sarafoglou, Alexandra; Matzke, Dora; Ly, Alexander; Boehm, Udo; Marsman, Maarten; Leslie, David S; Forster, Jonathan J; Wagenmakers, Eric-Jan; Steingroever, Helen

    2017-12-01

    The marginal likelihood plays an important role in many areas of Bayesian statistics such as parameter estimation, model comparison, and model averaging. In most applications, however, the marginal likelihood is not analytically tractable and must be approximated using numerical methods. Here we provide a tutorial on bridge sampling (Bennett, 1976; Meng & Wong, 1996), a reliable and relatively straightforward sampling method that allows researchers to obtain the marginal likelihood for models of varying complexity. First, we introduce bridge sampling and three related sampling methods using the beta-binomial model as a running example. We then apply bridge sampling to estimate the marginal likelihood for the Expectancy Valence (EV) model-a popular model for reinforcement learning. Our results indicate that bridge sampling provides accurate estimates for both a single participant and a hierarchical version of the EV model. We conclude that bridge sampling is an attractive method for mathematical psychologists who typically aim to approximate the marginal likelihood for a limited set of possibly high-dimensional models.

  19. Simulation and Optimization of Vacuum Swing Adsorption Units for Spacesuit Carbon Dioxide and Humidity Control

    Science.gov (United States)

    Swickrath, Michael J.; Anderson, Molly; McMillin, Summer; Broerman, Craig

    2011-01-01

    Controlling carbon dioxide (CO2) and humidity levels in a spacesuit is critical to ensuring both the safety and comfort of an astronaut during extra-vehicular activity (EVA). Traditionally, this has been accomplished utilizing either non-regenerative lithium hydroxide (LiOH) or regenerative but heavy metal oxide (MetOx) canisters which pose a significant weight burden. Although such technology enables air revitalization, the volume requirements to store the waste canisters as well as the mass to transport multiple units become prohibitive as mission durations increase. Consequently, motivation exists toward developing a fully regenerative technology for spacesuit environmental control. The application of solid amine materials with vacuum swing adsorption technology has shown the capacity to control CO2 while concomitantly managing humidity levels through a fully regenerative cycle eliminating constraints imposed with the traditional technologies. Prototype air revitalization units employing this technology have been fabricated in both a rectangular and cylindrical geometry. Experimental results for these test articles have been collected and are described herein. In order to accelerate the developmental efforts, an axially-dispersed plug flow model with an accompanying energy balance has been established and correlated with the experimental data. The experimental and simulation results display good agreement for a variety of flow rates (110-170 ALM), replicated metabolic challenges (100-590 Watts), and atmosphere pressures under consideration for the spacesuit (248 and 760 mm Hg). The testing and model results lend insight into the operational capabilities of these devices as well as the influence the geometry of the device has on performance. In addition, variable metabolic profiles were imposed on the test articles in order to assess the ability of the technology to transition to new metabolic conditions. The advent of the model provides the capacity to apply

  20. More extreme swings of the South Pacific convergence zone due to greenhouse warming.

    Science.gov (United States)

    Cai, Wenju; Lengaigne, Matthieu; Borlace, Simon; Collins, Matthew; Cowan, Tim; McPhaden, Michael J; Timmermann, Axel; Power, Scott; Brown, Josephine; Menkes, Christophe; Ngari, Arona; Vincent, Emmanuel M; Widlansky, Matthew J

    2012-08-16

    The South Pacific convergence zone (SPCZ) is the Southern Hemisphere's most expansive and persistent rain band, extending from the equatorial western Pacific Ocean southeastward towards French Polynesia. Owing to its strong rainfall gradient, a small displacement in the position of the SPCZ causes drastic changes to hydroclimatic conditions and the frequency of extreme weather events--such as droughts, floods and tropical cyclones--experienced by vulnerable island countries in the region. The SPCZ position varies from its climatological mean location with the El Niño/Southern Oscillation (ENSO), moving a few degrees northward during moderate El Niño events and southward during La Niña events. During strong El Niño events, however, the SPCZ undergoes an extreme swing--by up to ten degrees of latitude toward the Equator--and collapses to a more zonally oriented structure with commensurately severe weather impacts. Understanding changes in the characteristics of the SPCZ in a changing climate is therefore of broad scientific and socioeconomic interest. Here we present climate modelling evidence for a near doubling in the occurrences of zonal SPCZ events between the periods 1891-1990 and 1991-2090 in response to greenhouse warming, even in the absence of a consensus on how ENSO will change. We estimate the increase in zonal SPCZ events from an aggregation of the climate models in the Coupled Model Intercomparison Project phases 3 and 5 (CMIP3 and CMIP5) multi-model database that are able to simulate such events. The change is caused by a projected enhanced equatorial warming in the Pacific and may lead to more frequent occurrences of extreme events across the Pacific island nations most affected by zonal SPCZ events.

  1. Performance of an electrothermal swing adsorption system with postdesorption liquefaction for organic gas capture and recovery.

    Science.gov (United States)

    Mallouk, Kaitlin E; Rood, Mark J

    2013-07-02

    The use of adsorption on activated carbon fiber cloth (ACFC) followed by electrothermal swing adsorption (ESA) and postdesorption pressure and temperature control allows organic gases with boiling points below 0 °C to be captured from air streams and recovered as liquids. This technology has the potential to be a more sustainable abatement technique when compared to thermal oxidation. In this paper, we determine the process performance and energy requirements of a gas recovery system (GRS) using ACFC-ESA for three adsorbates with relative pressures between 8.3 × 10(-5) and 3.4 × 10(-3) and boiling points as low as -26.3 °C. The GRS is able to capture > 99% of the organic gas from the feed air stream, which is comparable to destruction efficiencies for thermal oxidizers. The energy used per liquid mole recovered ranges from 920 to 52,000 kJ/mol and is a function of relative pressure of the adsorbate in the feed gas. Quantifying the performance of the bench-scale gas recovery system in terms of its ability to remove organic gases from the adsorption stream and the energy required to liquefy the recovered organic gases is a critical step in developing new technologies to allow manufacturing to occur in a more sustainable manner. To our knowledge, this is the first time an ACFC-ESA system has been used to capture, recover, and liquefy organic compounds with vapor pressures as low as 8.3 × 10(-5) and the first time such a system has been analyzed for process performance and energy consumption.

  2. Constant speed control of four-stroke micro internal combustion swing engine

    Science.gov (United States)

    Gao, Dedong; Lei, Yong; Zhu, Honghai; Ni, Jun

    2015-09-01

    The increasing demands on safety, emission and fuel consumption require more accurate control models of micro internal combustion swing engine (MICSE). The objective of this paper is to investigate the constant speed control models of four-stroke MICSE. The operation principle of the four-stroke MICSE is presented based on the description of MICSE prototype. A two-level Petri net based hybrid model is proposed to model the four-stroke MICSE engine cycle. The Petri net subsystem at the upper level controls and synchronizes the four Petri net subsystems at the lower level. The continuous sub-models, including breathing dynamics of intake manifold, thermodynamics of the chamber and dynamics of the torque generation, are investigated and integrated with the discrete model in MATLAB Simulink. Through the comparison of experimental data and simulated DC voltage output, it is demonstrated that the hybrid model is valid for the four-stroke MICSE system. A nonlinear model is obtained from the cycle average data via the regression method, and it is linearized around a given nominal equilibrium point for the controller design. The feedback controller of the spark timing and valve duration timing is designed with a sequential loop closing design approach. The simulation of the sequential loop closure control design applied to the hybrid model is implemented in MATLAB. The simulation results show that the system is able to reach its desired operating point within 0.2 s, and the designed controller shows good MICSE engine performance with a constant speed. This paper presents the constant speed control models of four-stroke MICSE and carries out the simulation tests, the models and the simulation results can be used for further study on the precision control of four-stroke MICSE.

  3. Gender differences in triple jump phase ratios and arm swing motion of international level athletes

    Directory of Open Access Journals (Sweden)

    Vassilios Panoutsakopoulos

    2016-12-01

    Full Text Available Background: Female triple jumping is a relatively new athletics event. A limited number of researchers have focused on comparing male and female jumpers competing in international events, resulting in scarce findings in the literature regarding gender differences of the determinants of triple jump performance. Objective: The aim of the study was to examine the possible gender differences in the approach step characteristics, the spatiotemporal parameters of the separate phases of the triple jump as performed by athletes participating in sub-elite international events. Methods: The male and female participants of the 2015 European Team Championships triple jump event were recorded with a panning video camera. Approach speed was measured using photocells. Kinematical parameters were extracted using the APAS WIZARD 13.3.0.3 software. The relationships between the examined parameters and the actual triple jump performance were examined with Pearson's correlation analysis. Repeated measures ANOVA and chi-square statistical tests were run to examine the significance of the differences between genders. Results: Approach speed significantly correlated with the actual jumping distance in both males and females (p < .05. Significant gender differences (p < .05 existed concerning basic kinematical parameters. Men were found to have larger average horizontal speed of the 11 m to 1 m segment of the final approach, step length of the final six steps of the approach, step frequency of the final two steps, actual phase distances and percentage distribution of the step. Women, unlike men, used solely single arm swing techniques. No athlete executed the jump using a jump dominated technique. Conclusions: Gender differences in triple jump performance lies upon the kinematical parameters of the final two steps of the approach, the length of the step phase and the support time for the jump. The technique elements of the penultimate step are suggested to

  4. Engineering design solutions of flux swing with structural requirements for ohmic heating solenoids

    International Nuclear Information System (INIS)

    Smith, R.A.

    1977-01-01

    Here a more detailed publication is summarized which presents analytical methods with solutions that describe the structural behavior of ohmic heating solenoids to achieve a better understanding of the relationships between the functional variables that can provide the basis for recommended design improvements. The solutions relate the requirements imposed by structural integrity to the need for producing sufficient flux swing to initiate a plasma current in the tokamak fusion machine. A method is provided to perform a detailed structural analysis of every conducting turn in the radial build of the solenoid, and computer programmed listings for the closed form solutions are made available as part of the reference document. Distinction is made in deriving separate models for the regions of the solenoid where turn-to-turn radial contact is maintained with radial compression or with a bond in the presence of radial tension, and also where there is turn-to-turn radial separation due to the absence or the loss of bonding in the presence of would be radial tension. The derivations follow the theory of elasticity for a body possessing cylindrical anisotropy where the material properties are different in the radial and tangential directions. The formulations are made practical by presenting the methods for reducing stress and for relocating the relative position for potential turn-to-turn radial delamination by permitting an arbitrary traction at the outer radial surface of the solenoid in the form of pressure or displacement such as may be applied by a containment or a shrink fit structural cylinder

  5. Application of Vacuum Swing Adsorption for Carbon Dioxide and Water Vapor Removal from Manned Spacecraft Atmospheres

    Science.gov (United States)

    Knox, J.; Howard, D.

    2007-01-01

    In NASA's Vision for Space Exploration (Bush, 2004), (Griffin, 2007), humans will once again travel beyond the confines of earth's gravity, this time to remain there for extended periods. These forays will place unprecedented demands on launch systems. They must not only blast out of earth's gravity well as during the Apollo moon missions, but also liftoff the supplies needed to sustain a larger crew over much longer periods. Thus all spacecraft systems, including those for the separation of metabolic carbon dioxide and water from a crewed vehicle, must be minimized with respect to mass, power, and volume. Emphasis is also placed on system robustness both to minimize replacement parts and ensure crew safety when a quick return to earth is not possible. For short-term phases of manned space exploration, such as transit from the earth to the moon, venting of metabolic carbon dioxide and water to space is more efficient than the inclusion of large recycling systems on the spacecraft. The baseline system for the Orion spacecraft is an amine-based vacuum swing system (Smith, Perry et aI., 2006). As part of the development of an alternative approach, a sorbent-based CO2 and H2O removal system (Knox, Adams et aI., 2006), subscale testing was conducted to evaluate potential performance improvements obtainable by recuperating the heat of adsorption to aid in vacuum desorption. This bed design is shown in Figure 1, is depicted here with a lattice structure instead of reticulated foam for heat transfer. The slot widths are approximately 1.2 mm wide and 8.5 mm long. Bed depth is approximately 4.7 mm. Headers (not shown) were produced by the stereo lithography apparatus at MSFC.

  6. An Expert System for Concrete Bridge Management

    DEFF Research Database (Denmark)

    Brito, J. de; Branco, F. A.; Thoft-Christensen, Palle

    1997-01-01

    management systems are presently being implemented by bridge authorities in several countries. The prototype of an expert system for concrete bridge management is presented in this paper, with its functionality relying on two modules. The inspection module relies on a periodic acquisition of field......The importance of bridge repair versus new bridge construction has risen in recent decades due to high deterioration rates that have been observed in these structures. Budgets both for building new bridges and keeping the existing ones are always limited. To help rational decision-making, bridge...

  7. Precast concrete elements for accelerated bridge construction : laboratory testing, field testing, evaluation of a precast concrete bridge, Madison County bridge.

    Science.gov (United States)

    2009-01-01

    The importance of rapid construction technologies has been recognized by the Federal Highway Administration (FHWA) and the Iowa : DOT Office of Bridges and Structures. Recognizing this a two-lane single-span precast box girder bridge was constructed ...

  8. Excitation Methods for Bridge Structures

    Energy Technology Data Exchange (ETDEWEB)

    Farrar, C.R.; Duffy, T.A.; Cornwell, P.J.; Doebling, S.W.

    1999-02-08

    This paper summarizes the various methods that have been used to excited bridge structures during dynamic testing. The excitation methods fall into the general categories of ambient excitation methods and measured-input excitation methods. During ambient excitation the input to the bridge is not directly measured. In contrast, as the category label implies, measured-input excitations are usually applied at a single location where the force input to the structure can be monitored. Issues associated with using these various types of measurements are discussed along with a general description of the various excitation methods.

  9. Morphometry of the osteodural bridge and the myodural bridge of ...

    African Journals Online (AJOL)

    The osteodural bridge, the connective tissue between the axis and dura can be measured radiographically. The aim of the study was therefore to determine if there is a relationship between their lengths. Thirty formalin fixed cadavers were meticulously dissected at the department of Human Anatomy, University of Nairobi, ...

  10. Laboratory and field testing of an accelerated bridge construction demonstration bridge : US Highway 6 bridge over Keg Creek.

    Science.gov (United States)

    2013-04-01

    The US Highway 6 Bridge over Keg Creek outside of Council Bluffs, Iowa is a demonstration bridge site chosen to put into practice : newly-developed Accelerated Bridge Construction (ABC) concepts. One of these new concepts is the use of prefabricated ...

  11. Fiber reinforced polymer bridge decks : [technical summary].

    Science.gov (United States)

    2011-01-01

    A number of researchers have addressed the use of Fiber Reinforced Polymer (FRP) deck as a replacement solution for deteriorated bridge decks made of traditional materials. The use of new, advanced materials such as FRP is advantageous when the bridg...

  12. Developing county bridge repair and retrofit techniques.

    Science.gov (United States)

    2013-08-01

    Oklahoma rated first in the Nation in the percentage of bridges that are structurally deficient or : functionally obsolete. According to Federal Highway Administration data, Oklahoma uses : approximately 23,250 bridges maintained by state, County, Ci...

  13. Risk Mitigation for Highway and Railway Bridges

    Science.gov (United States)

    2009-02-01

    Performance of the transportation network strongly depends on the performance of bridges. Bridges constitute a vital part of the transportation infrastructure system and they are vulnerable to extreme events such as natural disasters (i.e., hurricane...

  14. Performance monitoring of jointless bridges : phase III.

    Science.gov (United States)

    2014-05-01

    Part I: : The third phase of a research project investigating the field performance of jointless bridges is reported. Three : integral abutment bridges in Vermont, US have been instrumented and monitored as part of this research. : General descriptio...

  15. IceBridge Mission Flight Reports

    Data.gov (United States)

    National Aeronautics and Space Administration — The IceBridge Mission Flight Reports data set contains flight reports from NASA Operation IceBridge Greenland, Arctic, Antarctic, and Alaska missions. Flight reports...

  16. Meeting Environmental Requirements after a Bridge Collapse

    Science.gov (United States)

    2008-08-01

    This report is intended to assist transportation and environmental professionals in the event of a bridge collapse or similar emergency. It analyzes the environmental review process in five cases of bridge reconstruction following collapse in Florida...

  17. Forensic testing of a double tee bridge.

    Science.gov (United States)

    2014-12-01

    This report describes an investigation to quantify the behavior of precast, prestressed concrete double-tee bridge : girders made with lightweight concrete. As part of the investigation, three bridge girders were salvaged from a : decommissioned brid...

  18. Microfluidic Wheatstone bridge for rapid sample analysis.

    Science.gov (United States)

    Tanyeri, Melikhan; Ranka, Mikhil; Sittipolkul, Natawan; Schroeder, Charles M

    2011-12-21

    We developed a microfluidic analogue of the classic Wheatstone bridge circuit for automated, real-time sampling of solutions in a flow-through device format. We demonstrate precise control of flow rate and flow direction in the "bridge" microchannel using an on-chip membrane valve, which functions as an integrated "variable resistor". We implement an automated feedback control mechanism in order to dynamically adjust valve opening, thereby manipulating the pressure drop across the bridge and precisely controlling fluid flow in the bridge channel. At a critical valve opening, the flow in the bridge channel can be completely stopped by balancing the flow resistances in the Wheatstone bridge device, which facilitates rapid, on-demand fluid sampling in the bridge channel. In this article, we present the underlying mechanism for device operation and report key design parameters that determine device performance. Overall, the microfluidic Wheatstone bridge represents a new and versatile method for on-chip flow control and sample manipulation.

  19. Characterization of bridge foundations workshop report.

    Science.gov (United States)

    2013-11-01

    "In 2013, the Federal Highway Administration proposed a new research program for the characterization of bridge foundations. To narrow the focus and develop a research roadmap for the program, a workshop on Characterization of Bridge Foundations...

  20. Phase and widening construction of steel bridges : [summary].

    Science.gov (United States)

    2014-03-01

    Maintaining traffic flow for bridge widening and replacement projects often requires bridges to be constructed in phases so that traffic can travel on one : portion of the bridge while another portion is being : constructed. The bridge portions are t...

  1. Bridge Design to Eurocodes – Worked examples

    OpenAIRE

    BOUASSIDA Yorsa; BOUCHON Emmanuel; CRESPO Pilar; CROCE Pietro; DAVAINE Laurence; DENTON Steve; FELDMANN Markus; FRANK Roger; HANSWILLE Gerhard; HENSEN Wolfang; KOLIAS Basil; MALAKATAS Nikolaos; MANCINI Giuseppe; ORTEGA CORNEJO Miguel; SEDLACEK Gerhard

    2011-01-01

    This document is a Technical Report with worked examples for a bridge structure designed following the Eurocodes. It summarizes important points of the Eurocodes for the design of concrete, steel and composite road bridges, including foundations and seismic design, utilizing a common bridge project as a basis. The geometry and materials of the example bridge as well as the main assumptions and the detailed structural calculations are presented in the first chapter of the report. Each of ...

  2. Field performance of timber bridges. 5, Little Salmon Creek stress-laminated deck bridge

    Science.gov (United States)

    M. A. Ritter; J. A. Kainz; G. J. Porter

    The Little Salmon Creek bridge was constructed in November 1988 on the Allegheny National Forest in Pennsylvania. The bridge is a simple span, single-lane, stress-laminated deck superstructure that is approximately 26-ft long and 16-ft wide. The bridge is unique in that it is the first known stress-laminated timber bridge to be constructed of hardwood lumber. The...

  3. Field performance of timber bridges. 6, Hoffman Run stress-laminated deck bridge

    Science.gov (United States)

    M. A. Ritter; P. D. Hilbrich Lee; G. J. Porter

    The Hoffman Run bridge, located just outside Dahoga, Pennsylvania, was constructed in October 1990. The bridge is a simple-span, single-lane, stress-laminated deck superstructure that is approximately 26 ft long and 16 ft wide. It is the second stress-laminated timber bridge to be constructed of hardwood lumber in Pennsylvania. The performance of the bridge was...

  4. 47 CFR 80.331 - Bridge-to-bridge communication procedure.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 5 2010-10-01 2010-10-01 false Bridge-to-bridge communication procedure. 80.331 Section 80.331 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) SAFETY AND SPECIAL..., Alarm, Urgency and Safety Procedures § 80.331 Bridge-to-bridge communication procedure. (a) Vessels...

  5. Bridge Programs in Illinois: Results of the 2010 Illinois Bridge Status Survey

    Science.gov (United States)

    Taylor, J. L.; Harmon, T.

    2010-01-01

    This report provides a summary of major results of the Illinois Bridge Status Survey, administered online between April and June 2010. The purpose of the survey was to understand the extent to which bridge programs are being implemented in Illinois, as well as to build an online directory of bridge programs. Bridge programs are an emerging…

  6. 75 FR 62181 - Annual Materials Report on New Bridge Construction and Bridge Rehabilitation

    Science.gov (United States)

    2010-10-07

    ... describing construction materials used in new Federal-aid bridge construction and bridge rehabilitation...), the FHWA has produced a report that summarizes the types of construction materials used in new bridge....fhwa.dot.gov/bridge/brdgtabs.cfm , consists of the following tables: Construction Materials for New and...

  7. 76 FR 55160 - Annual Materials Report on New Bridge Construction and Bridge Rehabilitation

    Science.gov (United States)

    2011-09-06

    ... describing construction materials used in new Federal-aid bridge construction and bridge rehabilitation... FHWA has produced a report that summarizes the types of construction materials used in new bridge....fhwa.dot.gov/bridge/brdgtabs.cfm , consists of the following tables: Construction Materials for New and...

  8. Control of bridge cranes with distributed-mass payloads under windy conditions

    Science.gov (United States)

    Tang, Rui; Huang, Jie

    2016-05-01

    Operating cranes is challenging because payloads experience large and dangerous oscillations, especially when the system is suffering from wind disturbances and the large-size payload is modeled as a distributed-mass model. The payload oscillations induced by both intentional motions commanded by the human operator and by the external wind disturbances make the dynamics more complicated. This paper presents a novel combined control architecture to limit oscillations of the distributed-mass payload caused by both human-operator commands and wind disturbances. While a smoothed command suppressed operator-induced oscillations, a wind-rejection command eliminated the payload swing resulting from the wind gusts. Through simulations, a large range of system parameters and motions are analyzed to investigate the dynamic behavior of bridge cranes with distributed-mass beams and wind disturbances by using the new control scheme. Experimental results obtained from a small-scale bridge crane validate the simulated dynamic behavior and the effectiveness of the proposed method.

  9. Project LOCAL - Bridging The Gap

    Science.gov (United States)

    Haven, Robert N.

    1975-01-01

    Project LOCAL, a not-for-profit regional consortium, offers a broad spectrum of in-service training courses tailored to meet the needs of educators in various disciplines and levels of experience. The purpose of these offerings is to bridge the communication gap between innovative centers in computer-oriented education and staff members in Boston…

  10. The Wien Bridge Oscillator Family

    DEFF Research Database (Denmark)

    Lindberg, Erik

    2006-01-01

    A tutorial in which the Wien bridge family of oscillators is defined and investigated. Oscillators which do not fit into the Barkhausen criterion topology may be designed. A design procedure based on initial complex pole quality factor is reported. The dynamic transfer characteristic...

  11. Talent Management: Bridging the Gap

    Science.gov (United States)

    2015-06-12

    culling continues at each grade. By this process, the model proposes to raise the talent distribution and level. Professional sports use this method... TALENT MANAGEMENT: BRIDGING THE GAP A thesis presented to the Faculty of the U.S. Army Command and General Staff College in...

  12. Evaluation of Summer Bridge Programs

    Science.gov (United States)

    Garcia, Lisa D.; Paz, Chiara C.

    2009-01-01

    Many colleges and universities in the United States offer summer programs for their incoming students. While programs are structured and administered in a variety of ways and target various student populations, the most common type of summer bridge program aims to serve historically underrepresented students and students of low socioeconomic…

  13. Optimizing Tailored Bus Bridging Paths

    NARCIS (Netherlands)

    Gu, Wei; Yu, Jie; Ji, Yuxiong; van der Gun, J.P.T.; Pel, A.J.; Zhang, H. Michael; van Arem, B.

    2017-01-01

    Metro disruptions due to unexpected events reduce transit system reliability, resulting in significant productivity loss and long passenger delays. Bus bridging strategy is often used to connect stations affected by metro disruptions such that passengers could continue their journey. The literature

  14. Accelerated bridge paint test program.

    Science.gov (United States)

    2011-07-06

    The accelerated bridge paint (AB-Paint) program evaluated a new Sherwin-Williams two-coat, : fast-curing paint system. The system is comprised of an organic zinc-rich primer (SW Corothane I : Galvapac One-Pack Zinc-Rich Primer B65 G11) and a polyurea...

  15. Detection of Ultrafine Anaphase Bridges

    DEFF Research Database (Denmark)

    Bizard, Anna H; Nielsen, Christian F; Hickson, Ian D

    2018-01-01

    Ultrafine anaphase bridges (UFBs) are thin DNA threads linking the separating sister chromatids in the anaphase of mitosis. UFBs are thought to form when topological DNA entanglements between two chromatids are not resolved prior to anaphase onset. In contrast to other markers of defective...

  16. Intercellular bridges in vertebrate gastrulation.

    Directory of Open Access Journals (Sweden)

    Luca Caneparo

    Full Text Available The developing zebrafish embryo has been the subject of many studies of regional patterning, stereotypical cell movements and changes in cell shape. To better study the morphological features of cells during gastrulation, we generated mosaic embryos expressing membrane attached Dendra2 to highlight cellular boundaries. We find that intercellular bridges join a significant fraction of epiblast cells in the zebrafish embryo, reaching several cell diameters in length and spanning across different regions of the developing embryos. These intercellular bridges are distinct from the cellular protrusions previously reported as extending from hypoblast cells (1-2 cellular diameters in length or epiblast cells (which were shorter. Most of the intercellular bridges were formed at pre-gastrula stages by the daughters of a dividing cell maintaining a membrane tether as they move apart after mitosis. These intercellular bridges persist during gastrulation and can mediate the transfer of proteins between distant cells. These findings reveal a surprising feature of the cellular landscape in zebrafish embryos and open new possibilities for cell-cell communication during gastrulation, with implications for modeling, cellular mechanics, and morphogenetic signaling.

  17. Nonlinear models of suspension bridges

    Czech Academy of Sciences Publication Activity Database

    Malík, Josef

    2006-01-01

    Roč. 321, č. 2 (2006), s. 828-850 ISSN 0022-247X Institutional research plan: CEZ:AV0Z30860518 Keywords : suspension bridges * principle of minimum energy Subject RIV: BA - General Mathematics Impact factor: 0.758, year: 2006

  18. Exodermic bridge deck performance evaluation.

    Science.gov (United States)

    2010-07-01

    In 1998, the Wisconsin DOT completed a two"leaf bascule bridge in Green Bay with an exodermic deck system. The exodermic deck consisted of 4.5"in thick cast"in"place reinforced concrete supported by a 5.19"in tall unfilled steel grid. The concrete an...

  19. Performance Characterization and Simulation of Amine-Based Vacuum Swing Sorption Units for Spacesuit Carbon Dioxide and Humidity Control

    Science.gov (United States)

    Swickrath, Michael J.; Watts, Carly; Anderson, Molly; McMillin, Summer; Broerman, Craig; Colunga, Aaron; Vogel, Matthew

    2012-01-01

    Controlling carbon dioxide (CO2) and water (H2O) vapor concentrations in a space suit is critical to ensuring an astronauts safety, comfort, and capability to perform extra-vehicular activity (EVA) tasks. Historically, this has been accomplished using lithium hydroxide (LiOH) and metal oxide (MetOx) canisters. Lithium hydroxide is a consumable material that requires priming with water before it becomes effective at removing carbon dioxide. MetOx is regenerable through a power-intensive thermal cycle but is significantly heavier on a volume basis than LiOH. As an alternative, amine-based vacuum swing beds are under aggressive development for EVA applications. The vacuum swing units control atmospheric concentrations of both CO2 and H2O through fully-regenerative process. The current concept, referred to as the rapid cycle amine (RCA), has resulted in numerous laboratory prototypes. Performance of these prototypes have been assessed experimentally and documented in previous reports. To support developmental e orts, a first principles model has also been established for the vacuum swing sorption technology. For the first time in several decades, a major re-design of Portable Life Support System (PLSS) for the extra-vehicular mobility unit (EMU) is underway. NASA at Johnson Space Center built and tested an integrated PLSS test bed of all subsystems under a variety of simulated EVA conditions of which the RCA prototype played a significant role. The efforts documented herein summarize RCA test performance and simulation results for single and variable metabolic rate experiments in an integrated context. In addition, a variety of off-nominal tests were performed to assess the capability of the RCA to function under challenging circumstances. Tests included high water production experiments, degraded vacuum regeneration, and deliberate valve/power failure and recovery.

  20. Performance Characterization and Simulation of Amine-Based Vacuum Swing Adsorption Units for Spacesuit Carbon Dioxide and Humidity Control

    Science.gov (United States)

    Swickrath, Michael J.; Watts,Carly; Anderson, Molly; McMillin, Summer; Boerman, Craig; Colunga, Aaron; Vogel, Matthew

    2011-01-01

    Controlling carbon dioxide (CO2) and water (H2O) concentrations in the vapor phase of a space suit is critical to ensuring an astronauts safety, comfortability, and capability to perform extra-vehicular activity (EVA) tasks. Historically, this has been accomplished using lithium hydroxide (LiOH) and metal oxides (MetOx). Lithium hydroxide is a consumable material and requires priming with water before it becomes effective at removing carbon dioxide. MetOx is regenerable through a power-intensive thermal cycle but is significantly heavier on a volume basis than LiOH. As an alternative, amine-based vacuum swing beds are under aggressive development for EVA applications which control atmospheric concentrations of both CO2 and H2O through a fully-regenerative process. The current concept, referred to as the rapid cycle amine (RCA), has resulted in numerous laboratory prototypes. Performance of these prototypes have been assessed and documented from experimental and theoretical perspectives. To support developmental efforts, a first principles model has also been established for the vacuum swing adsorption technology. The efforts documented herein summarize performance characterization and simulation results for several variable metabolic profiles subjected to the RCA. Furthermore, a variety of control methods are explored including timed swing cycles, instantaneous CO2 feedback control, and time-averaged CO2 feedback control. A variety of off-nominal tests are also explored including high/low suit temperatures, increasingly high humidity cases, and dynamic pressure cases simulating the suit pre-breathe protocol. Consequently, this work builds on efforts previous efforts to fully bound the performance of the rapid cycle amine under a variety of nominal and off-nominal conditions.

  1. Evaluation of a subject-specific female gymnast model and simulation of an uneven parallel bar swing.

    Science.gov (United States)

    Sheets, Alison L; Hubbard, Mont

    2008-11-14

    A gymnast model and forward dynamics simulation of a dismount preparation swing on the uneven parallel bars were evaluated by comparing experimental and predicted joint positions throughout the maneuver. The bar model was a linearly elastic spring with a frictional bar/hand interface, and the gymnast model consisted of torso/head, arm and two leg segments. The hips were frictionless balls and sockets, and shoulder movement was planar with passive compliant structures approximated by a parallel spring and damper. Subject-specific body segment moments of inertia, and shoulder compliance were estimated. Muscles crossing the shoulder and hip were represented as torque generators, and experiments quantified maximum instantaneous torques as functions of joint angle and angular velocity. Maximum torques were scaled by joint torque activations as functions of time to produce realistic motions. The downhill simplex method optimized activations and simulation initial conditions to minimize the difference between experimental and predicted bar-center, shoulder, hip, and ankle positions. Comparing experimental and simulated performances allowed evaluation of bar, shoulder compliance, joint torque, and gymnast models. Errors in all except the gymnast model are random, zero mean, and uncorrelated, verifying that all essential system features are represented. Although the swing simulation using the gymnast model matched experimental joint positions with a 2.15cm root-mean-squared error, errors are correlated. Correlated errors indicate that the gymnast model is not complex enough to exactly reproduce the experimental motion. Possible model improvements including a nonlinear shoulder model with active translational control and a two-segment torso would not have been identified if the objective function did not evaluate the entire system configuration throughout the motion. The model and parameters presented in this study can be effectively used to understand and improve an uneven

  2. Influence of optimization constraints in uneven parallel bar dismount swing simulations.

    Science.gov (United States)

    Sheets, Alison L; Hubbard, Mont

    2009-08-07

    Forward dynamics simulations of a dismount preparation swing on the uneven parallel bars were optimized to investigate the sensitivity of dismount revolution potential to the maximum bar force before slipping, and to low-bar avoidance. All optimization constraints were classified as 1-anatomical/physiological; limiting maximum hand force on the high bar before slipping, joint ranges of motion and maximum torques, muscle activation/deactivation timing and 2-geometric; avoiding low-bar contact, and requiring minimum landing distance. The gymnast model included torso/head, arm and two leg segments connected by a planar rotating, compliant shoulder and frictionless ball-and-socket hip joints. Maximum shoulder and hip torques were measured as functions of joint angle and angular velocity. Motions were driven by scaling maximum torques by a joint torque activation function of time which approximated the average activation of all muscles crossing the joint causing extension/flexion, or adduction/abduction. Ten joint torque activation values, and bar release times were optimized to maximize dismount revolutions using the downhill simplex method. Low-bar avoidance and maximum bar-force constraints are necessary because they reduce dismount revolution potential. Compared with the no low-bar performance, optimally avoiding the low bar by piking and straddling (abducting) the hips reduces dismount revolutions by 1.8%. Using previously reported experimentally measured peak uneven bar-force values of 3.6 and 4.0 body weight (BW) as optimization constraints, 1.40 and 1.55 revolutions with the body extended and arms overhead were possible, respectively. The bar-force constraint is not active if larger than 6.9 BW, and instead performances are limited only by maximum shoulder and hip torques. Bar forces accelerate the mass center (CM) when performing muscular work to flex/extend the joints, and increase gymnast mechanical energy. Therefore, the bar-force constraint inherently

  3. The Development and Validation of a Golf Swing and Putt Skill Assessment for Children

    Directory of Open Access Journals (Sweden)

    Lisa M. Barnett, Louise L. Hardy, Ali S. Brian

    2015-03-01

    Full Text Available The aim was to describe development of a process-oriented instrument designed to assess the golf swing and putt stroke, and to assess the instrument’s discriminative validity in terms of age and reliability (intra-rater and re-test. A Delphi consultation (with golf industry professionals and researchers in movement skill assessment was used to develop an assessment for each skill based on existing skill assessment protocols. Each skill had six components to be marked as present/absent. Individual scores were based on the number of performance components successfully demonstrated over two trials for each skill (potential score range 0 to 24. Children (n = 43 aged 6-10 years (M = 7.8 years, SD = 1.3 were assessed in both skills live in the field by one rater at Time 1(T1. A subset of children (n = 28 had consent for assessments to be videoed. Six weeks later 19 children were reassessed, five days apart (T2, T3. An ANOVA assessed discriminative validity i.e. whether skill competence at T1 differed by age (6 years, 7/8 years and 9/10 years. Intraclass correlations (ICC assessed intra-rater reliability between the live and video assessment at T1 and test-retest reliability (between T2 and T3. Paired t-tests assessed any systematic differences between live and video assessments (T1 and between T2 and T3. Older children were more skilled (F (2, 40 = 11.18, p < 0.001. The live assessment reflected the video assessment (ICC = 0.79, 95% CI 0.59, 0.90 and scores did not differ between live and video assessments. Test retest reliability was acceptable (ICC = 0.60, 95% CI 0.23, 0.82, although the mean score was slightly higher at retest. This instrument could be used reliably by golf coaches and physical education teachers as part of systematic early player assessment and feedback.

  4. Thermally moderated hollow fiber sorbent modules in rapidly cycled pressure swing adsorption mode for hydrogen purification

    KAUST Repository

    Lively, Ryan P.

    2012-10-01

    We describe thermally moderated multi-layered pseudo-monolithic hollow fiber sorbents entities, which can be packed into compact modules to provide small-footprint, efficient H2 purification/CO2 removal systems for use in on-site steam methane reformer product gas separations. Dual-layer hollow fibers are created via dry-jet, wet-quench spinning with an inner "active" core of cellulose acetate (porous binder) and zeolite NaY (69 wt% zeolite NaY) and an external sheath layer of pure cellulose acetate. The co-spun sheath layer reduces the surface porosity of the fiber and was used as a smooth coating surface for a poly(vinyl-alcohol) post-treatment, which reduced the gas permeance through the fiber sorbent by at least 7 orders of magnitude, essentially creating an impermeable sheath layer. The interstitial volume between the individual fibers was filled with a thermally-moderating paraffin wax. CO2 breakthrough experiments on the hollow fiber sorbent modules with and without paraffin wax revealed that the "passively" cooled paraffin wax module had 12.5% longer breakthrough times than the "non-isothermal" module. The latent heat of fusion/melting of the wax offsets the released latent heat of sorption/desorption of the zeolites. One-hundred rapidly cycled pressure swing adsorption cycles were performed on the "passively" cooled hollow fiber sorbents using 25 vol% CO2/75 vol% He (H2 surrogate) at 60 °C and 113 psia, resulting in a product purity of 99.2% and a product recovery of 88.1% thus achieving process conditions and product quality comparable to conventional pellet processes. Isothermal and non-isothermal dynamic modeling of the hollow fiber sorbent module and a traditional packed bed using gPROMS® indicated that the fiber sorbents have sharper fronts (232% sharper) and longer adsorbate breakthrough times (66% longer), further confirming the applicability of the new fiber sorbent approach for H2 purification. © 2012, Hydrogen Energy Publications, LLC

  5. Building Bridges One Line at a Time

    Science.gov (United States)

    Grigsby, Cathy Murray

    2012-01-01

    In this article, first-grade students were taught the different kinds of lines that were part of the construction of various bridges--the curved lines of the arches of stone bridges, straight lines connecting the cables of a suspension bridge, vertical lines, horizontal lines, and so on. They gained practice in drawing structures and in fine brush…

  6. Hydrodynamic forces on inundated bridge decks

    Science.gov (United States)

    2009-05-01

    The hydrodynamic forces experienced by an inundated bridge deck have great importance in the design of bridges. Specifically, the drag force, lift force, and the moment acting on the bridge deck under various levels of inundation and a range of flow ...

  7. Hydraulic forces on submerged bridge decks.

    Science.gov (United States)

    2008-09-01

    Bridge decks can be subjected to large horizontal forces when overtopping occurs. These forces may result in the displacement of bridge decks from the bents. This paper reports on the results of a laboratory study of horizontal forces on bridge decks...

  8. BRIDGES for Young Adolescents in North Dakota.

    Science.gov (United States)

    Harris, Mary McDonnell

    The BRIDGES Project was initiated to explore ways for North Dakota to provide young people with stronger bridges from childhood to adulthood. This report summarizes recommendations of the 1990-91 Governor's Task Force on Early Adolescence. The recommendations concern practical actions for the building of bridges by the following groups: (1)…

  9. Spread prestressed concrete slab beam bridges.

    Science.gov (United States)

    2015-04-01

    TxDOT uses prestressed slab beam bridges for short-span bridges ranging from approximately 3050 ft in : length. These bridges have precast, pretensioned slab beams placed immediately adjacent to one another : with a cast-in-place slab made composi...

  10. The experimental study of a new pressure equalization step in the pressure swing adsorption cycle of a portable oxygen concentrator.

    Science.gov (United States)

    Li, Jianhua

    2014-01-01

    For portable oxygen concentrator by pressure swing adsorption (PSA) method, its volume, mass, power, oxygen flux and oxygen saving efficiency are the most important parameters which are affected strongly by the PSA cycle. In this paper, we propose a new pressure equalization step to optimize the PSA cycle. According to the experimental results, when the product ends of two beds are connected and the feed gas is switched from the high pressure bed to the low pressure bed during the pressure equalization step, the system has a larger oxygen flux, a less energy consumption and a more simple structure.

  11. 33 CFR 115.70 - Advance approval of bridges.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Advance approval of bridges. 115... BRIDGES BRIDGE LOCATIONS AND CLEARANCES; ADMINISTRATIVE PROCEDURES § 115.70 Advance approval of bridges. (a) The General Bridge Act of 1946 requires the approval of the location and plans of bridges prior...

  12. Field performance of timber bridges. 4, Graves Crossing stress-laminated deck bridge

    Science.gov (United States)

    J. P. Wacker; M. A. Ritter

    The Graves Crossing bridge was constructed October 1991 in Antrim County, Michigan, as part of the demonstration timber bridge program sponsored by the USDA Forest Service. The bridge is a two-span continuous, stress-laminated deck superstructure and it is 36-ft long and 26-ft wide. The bridge is one of the first stress-laminated deck bridges to be built of sawn lumber...

  13. Further Research on an Anti-Swing Control System for Overhead Cranes

    Directory of Open Access Journals (Sweden)

    B. Spruogis

    2018-02-01

    Full Text Available A method of reducing load oscillations that occur when overhead crane reaches destination position is presented in the article. The use of control drive scheme of crane bridge and trolley that ensures a smooth phase trajectory transition of the load to the optimum trajectory in accordance with Pontryagin's maximum principle is proposed. Mentioned control system changes the magnitude or direction of the traction force at the moment when the load is located above the destination. It is found that the degree of change of the traction force depends on the hoisting rope deviation angle from vertical. This study was conducted in order to provide more accurate and fast handling of loads by overhead crane.

  14. Heavy Vehicles on Minor Highway Bridges

    DEFF Research Database (Denmark)

    Kirkegaard, Poul Henning; Nielsen, Søren R. K.; Enevoldsen, I.

    Vibration of a bridge structure due to the passage of vehicles is an important consideration in the design of bridges. Further, a common problem in bridge engineering practice in these years is the upgrading of minor highway bridges (=5-20 m) to carry heavier loads partly due to a tendency...... of heavier trucks moving at larger speeds, and partly because the authorities want to permit transportation of special heavy goods at a larger part of the road net. These needs will in many cases cause the strengthening of the bridges becomes necessary. In order to keep the expenses of such strengthening....... Each axle is suspended on two elastic supports modelling the wheels....

  15. Effects of Electrolyte on Floating Water Bridge

    OpenAIRE

    Hideo Nishiumi; Fumitaka Honda

    2009-01-01

    Fuchs found phenomena that when high voltage is applied to deionized water filled in two contacted beakers, a floating water bridge forms spontaneously. In this paper, we examined flow direction of water bridge and what effects the addition of electrolytes such as NaCl, NaOH, and N H 4 C l to the floating water bridge would give. We found that ionization degree reduced the length of water bridge though insoluble electrolyte A l 2 O 3 had no effect on the length of water bridge.

  16. Beginning Course Surveys: Bridges for Knowing and Bridges for Being

    Directory of Open Access Journals (Sweden)

    David Starr-Glass

    2011-06-01

    Full Text Available The use of a participant survey, administered at the outset of an online course, can provide information useful in the management of the learning environment and in its subsequent redesign. Such information can clarify participants’ prior experience, expectations, and demographics. But the very act of enquiring about the learner also signals the instructor’s social presence, relational interest, and desire to enter into an authentic dialogue. This study examines the use of participant surveys in online management courses. The first section discusses the informational bridges that this instrument provides. The second section considers survey responses to open-ended questions dealing with student sentiments. This analysis suggests that the survey plays a valuable part in accentuating social presence and in initiating relational bridges with participants.

  17. Heavy Vehicles on Minor Highway Bridges

    DEFF Research Database (Denmark)

    Kirkegaard, Poul Henning; Nielsen, Søren R. K.; Enevoldsen, I.

    Vibration of a bridge structure due to the passage of vehicles is an important consideration in the design of bridges. Further, a common problem in bridge engineering practice in these years is the upgrading of minor highway bridges (=5-20 m) to carry heavier loads partly due to a tendency...... of heavier trucks moving at larger speeds, and partly because the authorities want to permit transportation of special heavy goods at a larger part of the road net. These needs will in many cases cause the strengthening of the bridges becomes necessary. In order to keep the expenses of such strengthening...... the numerical models for the mathematical models of the vehicles and the bridge from which the load amplification factors can be estimated assuming that the dynamic parameters of the vehicles and the modal parameters of the bridge are known....

  18. Strengthening Bridges with Prestressed CFRP Strips

    Science.gov (United States)

    Siwowski, Tomasz; Żółtowski, Piotr

    2012-06-01

    Limitation of bridge's carrying bearing capacity due to aging and deterioration is a common problem faced by road administration and drivers. Rehabilitation of bridges including strengthening may be applied in order to maintain or upgrade existing bridge parameters. The case studies of strengthening of two small bridges with high modulus prestressed CFRP strips have been presented in the paper. The first one - reinforced concrete slab bridge - and the other - composite steel-concrete girder bridge - have been successfully upgraded with quite new technology. In both cases the additional CFRP reinforcement let increasing of bridge carrying capacity from 15 till 40 metric tons. The CFRP strip prestressing system named Neoxe Prestressing System (NPS), developed by multi-disciplinary team and tested at full scale in Rzeszow University of Technology, has been also described in the paper.

  19. Black Phosphorus Based Field Effect Transistors with Simultaneously Achieved Near Ideal Subthreshold Swing and High Hole Mobility at Room Temperature.

    Science.gov (United States)

    Liu, Xinke; Ang, Kah-Wee; Yu, Wenjie; He, Jiazhu; Feng, Xuewei; Liu, Qiang; Jiang, He; Dan Tang; Wen, Jiao; Lu, Youming; Liu, Wenjun; Cao, Peijiang; Han, Shun; Wu, Jing; Liu, Wenjun; Wang, Xi; Zhu, Deliang; He, Zhubing

    2016-04-22

    Black phosphorus (BP) has emerged as a promising two-dimensional (2D) material for next generation transistor applications due to its superior carrier transport properties. Among other issues, achieving reduced subthreshold swing and enhanced hole mobility simultaneously remains a challenge which requires careful optimization of the BP/gate oxide interface. Here, we report the realization of high performance BP transistors integrated with HfO2 high-k gate dielectric using a low temperature CMOS process. The fabricated devices were shown to demonstrate a near ideal subthreshold swing (SS) of ~69 mV/dec and a room temperature hole mobility of exceeding >400 cm(2)/Vs. These figure-of-merits are benchmarked to be the best-of-its-kind, which outperform previously reported BP transistors realized on traditional SiO2 gate dielectric. X-ray photoelectron spectroscopy (XPS) analysis further reveals the evidence of a more chemically stable BP when formed on HfO2 high-k as opposed to SiO2, which gives rise to a better interface quality that accounts for the SS and hole mobility improvement. These results unveil the potential of black phosphorus as an emerging channel material for future nanoelectronic device applications.

  20. Eu, tu, ele(s, ela(s: cartografando heteroconjugalidades na prática do swing

    Directory of Open Access Journals (Sweden)

    Andréa Marília Alves de Oliveira

    2015-12-01

    Full Text Available Resumo As experimentações da sexualidade produzidas nas heteroconjugalidades contemporâneas têm vivido transições nos seus suportes afetivo-relacionais, maior flexibilização em suas hierarquias de gênero e enriquecimento das suas possibilidades institucionais. Problematizaremos a prática do swing como uma das linhas de tensionamento produzidas nesta agonística cultural, tomando como objeto de estudo hetero/casais em cenas eróticas ‘dissidentes’. Nesta cena da pesquisa nos valemos de conversações entre interlocutoras/res swingers cearenses e uma das pesquisadoras. Os princípios do método do nosso estudo se (desacomodam em perspectivas feministas e desde os estudos queer, assumindo um modo de análise em posição discursivo-desconstrucionista, a partir dos pressupostos foucaultianos da análise do discurso. Esta cartografia íntima nos permitiu acompanhar algo dos/nos trânsitos das relações hetero/conjugais contemporâneas e suas (dissidentes performances de gênero e experimentações das sexualidades. De modo que assumimos, pelo instante, a ideia do swing como prática de subjetivação e modo de experimentação da heteroconjugalidade.

  1. A Novel Approach to Determine Strides, Ice Contact, and Swing Phases During Ice Hockey Skating Using a Single Accelerometer.

    Science.gov (United States)

    Stetter, Bernd J; Buckeridge, Erica; von Tscharner, Vinzenz; Nigg, Sandro R; Nigg, Benno M

    2016-02-01

    This study presents a new approach for automated identification of ice hockey skating strides and a method to detect ice contact and swing phases of individual strides by quantifying vibrations in 3D acceleration data during the blade-ice interaction. The strides of a 30-m forward sprinting task, performed by 6 ice hockey players, were evaluated using a 3D accelerometer fixed to a hockey skate. Synchronized plantar pressure data were recorded as reference data. To determine the accuracy of the new method on a range of forward stride patterns for temporal skating events, estimated contact times and stride times for a sequence of 5 consecutive strides was validated. Bland-Altman limits of agreement (95%) between accelerometer and plantar pressure derived data were less than 0.019 s. Mean differences between the 2 capture methods were shown to be less than 1 ms for contact and stride time. These results demonstrate the validity of the novel approach to determine strides, ice contact, and swing phases during ice hockey skating. This technology is accurate, simple, effective, and allows for in-field ice hockey testing.

  2. Bio-inspired swing leg control for spring-mass robots running on ground with unexpected height disturbance.

    Science.gov (United States)

    Vejdani, H R; Blum, Y; Daley, M A; Hurst, J W

    2013-12-01

    We proposed three swing leg control policies for spring-mass running robots, inspired by experimental data from our recent collaborative work on ground running birds. Previous investigations suggest that animals may prioritize injury avoidance and/or efficiency as their objective function during running rather than maintaining limit-cycle stability. Therefore, in this study we targeted structural capacity (maximum leg force to avoid damage) and efficiency as the main goals for our control policies, since these objective functions are crucial to reduce motor size and structure weight. Each proposed policy controls the leg angle as a function of time during flight phase such that its objective function during the subsequent stance phase is regulated. The three objective functions that are regulated in the control policies are (i) the leg peak force, (ii) the axial impulse, and (iii) the leg actuator work. It should be noted that each control policy regulates one single objective function. Surprisingly, all three swing leg control policies result in nearly identical subsequent stance phase dynamics. This implies that the implementation of any of the proposed control policies would satisfy both goals (damage avoidance and efficiency) at once. Furthermore, all three control policies require a surprisingly simple leg angle adjustment: leg retraction with constant angular acceleration.

  3. Noise Considerations in Resistance Bridges

    DEFF Research Database (Denmark)

    Diamond, Joseph M.

    1963-01-01

    A signal-to-noise analysis is made of the Wheatstone bridge, where the unknown and standard resistors may be at different temperatures, a situation which occurs in resistance thermometry. The limiting condition is assumed to be dissipation in the unknown resistor. It is shown that the ratio arms...... should be low in resistance compared with the unknown resistor, while the standard resistor should be high. This is true to an extreme degree when the unknown resistor is at liquid helium temperatures, and the standard resistor at room temperature. This factor is much less important in high temperature...... thermometry, where the noise in the unknown resistor will predominate strongly. An impedance step-up device (transformer or tuned circuit) is valuable in raising the bridge signal and noise level above the noise of the first amplifier tube. However, as the step-up ratio is increased, two counterfactors appear...

  4. Physical Adsorption of Gases on Heterogeneous Solids and Equilibrium Studies of the Pressure Swing Adsorption Process.

    Science.gov (United States)

    Lu, Xiaochun

    1990-01-01

    -parameter isotherm equation based on benzene adsorption isotherms. We extended further the TVFM to derive thermodynamic functions, such as the adsorption entropy, the adsorption enthalpy, and the adsorption energy distribution, and constructed these functions for various adsorption systems based on their adsorption isotherms. To explore the energetic heterogeneity of the adsorbent, we used two approaches. First, we used the overall integral isotherm equation to obtain the Langmuir -Freundlich isotherm; and second, we used the Gibb's relation to obtain an exponential isotherm equation. The adsorption energy-distribution function can be obtained from these isotherm equations. The pressure swing adsorption (PSA) process was studied based on Shandalman and Mitchell's equilibrium theory for a PSA system with a linear isotherm. This theory was extended to a PSA system with a non-linear isotherm. Relationships were established between the isotherms and process parameters, such as the enrichment factor, the critical recycle ratio, and the extent of the recovery.

  5. Cross-Quint-Bridge Resistor

    Science.gov (United States)

    Hannaman, David J.; Lieneweg, Udo; Buehler, Martin G.; Mantalas, Linda

    1991-01-01

    Integrated-circuit conductive test pattern intended to provide data on effects of design widths and design spacings upon actual widths of conductive lines. Provides for electrical measurements both on lines of unknown width and on features having known dimensions. Data from measurements on five bridges used to determine four parameters of mathematical model describing system. In principle, pattern determines effects of width and spacing and interaction between them.

  6. Melanoma and immunotherapy bridge 2015

    OpenAIRE

    Nanda, Vashisht G. Y.; Peng, Weiyi; Hwu, Patrick; Davies, Michael A.; Ciliberto, Gennaro; Fattore, Luigi; Malpicci, Debora; Aurisicchio, Luigi; Ascierto, Paolo Antonio; Croce, Carlo M.; Mancini, Rita; Spranger, Stefani; Gajewski, Thomas F.; Wang, Yangyang; Ferrone, Soldano

    2016-01-01

    Table of contents MELANOMA BRIDGE 2015 KEYNOTE SPEAKER PRESENTATIONS Molecular and immuno-advances K1 Immunologic and metabolic consequences of PI3K/AKT/mTOR activation in melanoma Vashisht G. Y. Nanda, Weiyi Peng, Patrick Hwu, Michael A. Davies K2 Non-mutational adaptive changes in melanoma cells exposed to BRAF and MEK inhibitors help the establishment of drug resistance Gennaro Ciliberto, Luigi Fattore, Debora Malpicci, Luigi Aurisicchio, Paolo Antonio Ascierto, Carlo M. Croce, Rita Mancin...

  7. Severe ASR damaged concrete bridges

    DEFF Research Database (Denmark)

    Antonio Barbosa, Ricardo; Gustenhoff Hansen, Søren

    2015-01-01

    Technical University of Denmark (DTU) and University of Southern Denmark (SDU) have conducted several full-scale experiments with severe ASR deteriorated bridges. This paper presents few and preliminary results from both the shear tests and the measuring of the material properties. The shear test...... show that the shear capacity is almost unaffected of ASR despite significant reduction in compressive concrete strength. Furthermore, measurements show a significant tensile reinforcement strain developed due to ASR expansion....

  8. Inspection Strategies for Concrete Bridges

    DEFF Research Database (Denmark)

    Sørensen, John Dalsgaard; Thoft-Christensen, Palle

    1989-01-01

    In this paper an optimal inspection strategy for concrete bridges based on periodic routine and detailed inspections is presented. The failure mode considered is corrosion of the reinforcement due to chlorides. A simple modelling of the corrosion and of the inspection strategy is presented....... The optimal inspection strategy is determined from an optimization problem, where the design variables are time intervals between detailed inspections and the concrete cover. The strategy is illustrated on a simple structure, namely a reinforced concrete beam....

  9. 2-D analytical modeling of subthreshold current and subthreshold swing for ion-implanted strained-Si double-material double-gate (DMDG) MOSFETs

    Science.gov (United States)

    Goel, Ekta; Singh, Kunal; Singh, Balraj; Kumar, Sanjay; Jit, Satyabrata

    2017-09-01

    In this paper, the subthreshold behavior of ion-implanted strained-Si double-material double-gate (DMDG) MOSFETs has been analyzed by means of subthreshold current and subthreshold swing. The surface potential based formulation of subthreshold current and subthreshold swing is done by solving the 2-D Poisson's equations in the channel region using parabolic approximation method. The dependence of subthreshold characteristics on various device parameters such as gate length ratio, Ge mole fraction, peak doping concentration, projected range, straggle parameter etc. has been studied. The modeling results are found to be well matched with the simulation data obtained by a 2-D device simulator, ATLAS™, from SILVACO.

  10. Salt bridges: geometrically specific, designable interactions.

    Science.gov (United States)

    Donald, Jason E; Kulp, Daniel W; DeGrado, William F

    2011-03-01

    Salt bridges occur frequently in proteins, providing conformational specificity and contributing to molecular recognition and catalysis. We present a comprehensive analysis of these interactions in protein structures by surveying a large database of protein structures. Salt bridges between Asp or Glu and His, Arg, or Lys display extremely well-defined geometric preferences. Several previously observed preferences are confirmed, and others that were previously unrecognized are discovered. Salt bridges are explored for their preferences for different separations in sequence and in space, geometric preferences within proteins and at protein-protein interfaces, co-operativity in networked salt bridges, inclusion within metal-binding sites, preference for acidic electrons, apparent conformational side chain entropy reduction on formation, and degree of burial. Salt bridges occur far more frequently between residues at close than distant sequence separations, but, at close distances, there remain strong preferences for salt bridges at specific separations. Specific types of complex salt bridges, involving three or more members, are also discovered. As we observe a strong relationship between the propensity to form a salt bridge and the placement of salt-bridging residues in protein sequences, we discuss the role that salt bridges might play in kinetically influencing protein folding and thermodynamically stabilizing the native conformation. We also develop a quantitative method to select appropriate crystal structure resolution and B-factor cutoffs. Detailed knowledge of these geometric and sequence dependences should aid de novo design and prediction algorithms. Copyright © 2010 Wiley-Liss, Inc.

  11. Road Bridges and Culverts, Bridge dataset only includes bridges maintained by Johnson County Public Works in the unincorporated areas, Published in Not Provided, Johnson County Government.

    Data.gov (United States)

    NSGIC Local Govt | GIS Inventory — Road Bridges and Culverts dataset current as of unknown. Bridge dataset only includes bridges maintained by Johnson County Public Works in the unincorporated areas.

  12. Horizontal bridges in polar dielectric liquids

    Science.gov (United States)

    Woisetschläger, Jakob; Wexler, Adam D.; Holler, Gert; Eisenhut, Mathias; Gatterer, Karl; Fuchs, Elmar C.

    2012-01-01

    When a high-voltage direct-current is applied to two beakers filled with polar liquid dielectrica like water or methanol, a horizontal bridge forms between the two beakers. By repeating a version of Pellat's experiment, it is shown that a horizontal bridge is stable by the action of electrohydrodynamic pressure. Thus, the static and dynamic properties of the phenomenon called a `floating water bridge' can be explained by the gradient of Maxwell pressure, replenishing the liquid within the bridge against any drainage mechanism. It is also shown that a number of liquids can form stable and long horizontal bridges. The stability of such a connection, and the asymmetry in mass flow through such bridges caused by the formation of ion clouds in the vicinity of the electrodes, is also discussed by two further experiments.

  13. Bridge engineering handbook construction and maintenance

    CERN Document Server

    Chen, Wai-Fah

    2014-01-01

    Over 140 experts, 14 countries, and 89 chapters are represented in the second edition of the Bridge Engineering Handbook. This extensive collection highlights bridge engineering specimens from around the world, contains detailed information on bridge engineering, and thoroughly explains the concepts and practical applications surrounding the subject.Published in five books: Fundamentals, Superstructure Design, Substructure Design, Seismic Design, and Construction and Maintenance, this new edition provides numerous worked-out examples that give readers step-by-step design procedures, includes c

  14. Markovian bridges: Weak continuity and pathwise constructions

    OpenAIRE

    Chaumont, Loïc; Uribe Bravo, Gerónimo

    2011-01-01

    A Markovian bridge is a probability measure taken from a disintegration of the law of an initial part of the path of a Markov process given its terminal value. As such, Markovian bridges admit a natural parameterization in terms of the state space of the process. In the context of Feller processes with continuous transition densities, we construct by weak convergence considerations the only versions of Markovian bridges which are weakly continuous with respect to their parameter. We use this ...

  15. Removal of failed crown and bridge

    OpenAIRE

    Sharma, Ashu; Rahul, G.R.; Poduval, Soorya T.; Shetty, Karunakar

    2012-01-01

    Crown and bridge have life span of many years but they fail for a number of reasons. Over the years, many devices have been designed to remove crowns and bridges from abutment teeth. While the removal of temporary crowns and bridges is usually very straightforward, the removal of a definitive cast crown with unknown cement is more challenging. Removal is often by destructive means. There are a number of circumstances, however, in which conservative disassembly would aid the practitioner in co...

  16. Measurement of Deflection Line on Bridges

    Science.gov (United States)

    Urban, Rudolf; Štroner, Martin

    2013-12-01

    Prestressed concrete bridges are very sensitive to the increase in long-term deflections. Reliable forecasts of deflections of bridge structures during construction and durability are crucial for achieving good durability. The main results of measurements are the changes of the deflection line of the bridge structures, which places special demands on the measurement procedure. Results from measurements are very useful for the improvement of mathematical prediction methods of behaviour of long span prestressed concrete structures.

  17. Industrial steel hall with bridge grane

    OpenAIRE

    Jurejevčič, Nejc

    2016-01-01

    In introduction this diploma thesis describes all main characteristics of (single block)? industrial steel hall with bridge crane. Load arrangement on the supporting structure which covers general actions (snow load and wind action), self-weight and dynamic load of bridge crane was designed with moment resisting frame in transverse direction and frame with concentric diagonal bracing in longitudinual direction. Actions induced by crane bridge was considered in design of runway beam. Steel hal...

  18. Dynamic assessment of bridge deck performance considering realistic bridge-traffic interaction : research brief

    Science.gov (United States)

    2017-09-01

    This study is to develop simulation methodology to conduct the dynamic assessment of bridge deck performance subjected to traffic. Concrete bridge decks are exposed to daily traffic loads and may experience some surface cracking caused by excessive s...

  19. Evaluation of the Buena Vista IBRD bridge : a furthering of accelerated bridge construction in Iowa.

    Science.gov (United States)

    2012-02-01

    The need to construct bridges that last longer, are less expensive, and take less time to build has increased. The importance of accelerated bridge construction (ABC) technologies has been realized by the Federal Highway Administration (FHWA) and the...

  20. SSI-bridge : soil bridge interaction during long-duration earthquake motions.

    Science.gov (United States)

    2014-09-01

    The seismic response of a complete soil-bridge system during shallow, crustal and subduction zone earthquakes is the topic of this report. Specifically, the effects of earthquake duration on the seismic performance of soil-bridge systems are examined...

  1. Review of Energy Harvesters Utilizing Bridge Vibrations

    Directory of Open Access Journals (Sweden)

    Farid Ullah Khan

    2016-01-01

    Full Text Available For health monitoring of bridges, wireless acceleration sensor nodes (WASNs are normally used. In bridge environment, several forms of energy are available for operating WASNs that include wind, solar, acoustic, and vibration energy. However, only bridge vibration has the tendency to be utilized for embedded WASNs application in bridge structures. This paper reports on the recent advancements in the area of vibration energy harvesters (VEHs utilizing bridge oscillations. The bridge vibration is narrowband (1 to 40 Hz with low acceleration levels (0.01 to 3.8 g. For utilization of bridge vibration, electromagnetic based vibration energy harvesters (EM-VEHs and piezoelectric based vibration energy harvesters (PE-VEHs have been developed. The power generation of the reported EM-VEHs is in the range from 0.7 to 1450000 μW. However, the power production by the developed PE-VEHs ranges from 0.6 to 7700 μW. The overall size of most of the bridge VEHs is quite comparable and is in mesoscale. The resonant frequencies of EM-VEHs are on the lower side (0.13 to 27 Hz in comparison to PE-VEHs (1 to 120 Hz. The power densities reported for these bridge VEHs range from 0.01 to 9539.5 μW/cm3 and are quite enough to operate most of the commercial WASNs.

  2. Assessment of the Reliability of Concrete Bridges

    DEFF Research Database (Denmark)

    Middleton, C. R.; Thoft-Christensen, Palle

    a significant shift in emphasis for the highways authorities around the world away from the design of new structures over to maintaining the existing infrastructure. As a result, bridge owners are seeking improved ways of inspecting, assessing, maintaining and repairing their existing stock of bridges...... in the wake of ever increasing traffic loads and volumes, and an ageing population of bridges subject to various mechanisms of deterioration. The goal is to optimise the allocation of limited resources whilst maintaining their bridges in a safe and serviceable condition. Reliability analysis is one tool being...

  3. The I-35W bridge Project Website

    DEFF Research Database (Denmark)

    Kampf, Constance

    How can websites be used to rebuild trust?  In August 2007, the Interstate Highway 35-W bridge in Minneapolis, MN collapsed during rush hour.  Although many people were rescued and casualties were as limited as could be expected due to quick and effective intervention, the image of a major bridge......, and the use of multimodal features.  This paper looks at the I35-W bridge reconstruction project in Minneapolis through web-based communication by the Minnesota Department of Transportation (MnDOT) about the project. The MnDOT bridge reconstruction website will be examined using a combination of 1). Weick...

  4. A data management infrastructure for bridge monitoring

    Science.gov (United States)

    Jeong, Seongwoon; Byun, Jaewook; Kim, Daeyoung; Sohn, Hoon; Bae, In Hwan; Law, Kincho H.

    2015-04-01

    This paper discusses a data management infrastructure framework for bridge monitoring applications. As sensor technologies mature and become economically affordable, their deployment for bridge monitoring will continue to grow. Data management becomes a critical issue not only for storing the sensor data but also for integrating with the bridge model to support other functions, such as management, maintenance and inspection. The focus of this study is on the effective data management of bridge information and sensor data, which is crucial to structural health monitoring and life cycle management of bridge structures. We review the state-of-the-art of bridge information modeling and sensor data management, and propose a data management framework for bridge monitoring based on NoSQL database technologies that have been shown useful in handling high volume, time-series data and to flexibly deal with unstructured data schema. Specifically, Apache Cassandra and Mongo DB are deployed for the prototype implementation of the framework. This paper describes the database design for an XML-based Bridge Information Modeling (BrIM) schema, and the representation of sensor data using Sensor Model Language (SensorML). The proposed prototype data management framework is validated using data collected from the Yeongjong Bridge in Incheon, Korea.

  5. CONDITION RATING SYSTEM FOR THAILAND'S CONCRETE BRIDGES

    Directory of Open Access Journals (Sweden)

    Bonaventure H.W. Hadikusumo

    2010-06-01

    Full Text Available The Bridge Management System is designed to maximise use of available data and determine the optimal strategy to perform necessary improvements to bridges in the most cost-effective manner. This paper provides a condition rating system to meet the requirements of Thailand’s Department of Highways (DOH. A rating system to assess the existing condition of bridges is proposed. Segmental inspection is developed to execute efficient element-level evaluations and collect data that demonstrate deterioration patterns in bridge elements. The paper also describes inspection procedures for field survey execution, which enables observed distresses at the level of sub-elements or members to be allocated. Recommendations from bridge experts reveal that the proposed rating system is robust, implementable in actual practice, and suitable for efficient application in evaluating the nation’s concrete highway bridges. Although the bridge condition rating was developed in response to the specific characteristics of Thailand’s bridges, the proposed methodology can easily be extended to other bridge agencies.

  6. A Polish approach to FRP bridges

    Science.gov (United States)

    Siwowski, Tomasz; Rajchel, Mateusz

    2017-12-01

    The paper presents initial results of a new approach to FRP composite bridge construction that is presently being developed and tested in Poland. The concept combines lightweight concrete with FRP composites to create a durable highly optimised structure. The paper describes the bridge system itself and presents the research results on its development. The basic design is presented together with research results on its development: FEM analysis and a range of static test results of full-scale bridge beam experiments. The paper finishes with some test results of a full scale bridge that was constructed near Rzeszow in December 2015.

  7. Factory test results on NOx recycle system using pressure swing adsorption method (PSA-method) for Rokkasho Reprocessing Plant

    International Nuclear Information System (INIS)

    Sakai, Masami; Nakamura, Kou; Shimizu, Yoshinao; Kubota, Masaru; Takeishi, Masayuki; Kumura, Seiji

    2005-01-01

    At Rokkasho Reprocessing Plant (RRR), a great deal of NOx is mainly used as oxidizing reagent of Pu. This NOx has been conventionally manufactured by reaction of sodium nitrite and nitric acid. Problem, however, was how to process the radioactive waste materials left after immunization of the non-radioactive sodium nitrite occurring in manufacturing and the residual NOx used in the reprocessing. This paper reports the factory test results on the recycle system for NOx from denitrating tower off-gas using PSA method (vacuum pressure swing adsorption method) which has been developed to reduce waste materials occurring in the manufacture of NOx and the processing of residual NOx in the off-gas. (author)

  8. Field performance of timber bridges. 9, Big Erick`s stress-laminated deck bridge

    Science.gov (United States)

    J. A. Kainz; J. P. Wacker; M. Nelson

    The Big Erickas bridge was constructed during September 1992 in Baraga County, Michigan. The bridge is 72 ft long, 16 ft wide, and consists of three simple spans: two stress-laminated deck approach spans and a stress-laminated box center span. The bridge is unique in that it is one of the first known stress-laminated timber bridge applications to use Eastern Hemlock...

  9. Element Level Bridge Inspection: Benefits and Use of Data for Bridge Management

    OpenAIRE

    Campbell, Leslie E.; Perry, Chase N.; Connor, Robert J.; Lloyd, Jason B.

    2016-01-01

    In 2012, Congress passed the Moving Ahead for Progress in the 21st Century Act (MAP-21) and committed to the development of a data-driven, risk based approach to asset management in the United States. This law requires the collection and submission of element level bridge inspection data for all National Highway System bridges, in addition to the National Bridge Inspection condition rating data. Ultimately, the data collected during element level bridge inspections should satisfy the requirem...

  10. 33 CFR 118.65 - Lights on fixed bridges.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Lights on fixed bridges. 118.65 Section 118.65 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY BRIDGES BRIDGE LIGHTING AND OTHER SIGNALS § 118.65 Lights on fixed bridges. (a) Each fixed bridge span over a navigable...

  11. 33 CFR 118.90 - Bridges crossing channel obliquely.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Bridges crossing channel obliquely. 118.90 Section 118.90 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY BRIDGES BRIDGE LIGHTING AND OTHER SIGNALS § 118.90 Bridges crossing channel obliquely. Bridges...

  12. 33 CFR 118.85 - Lights on vertical lift bridges.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Lights on vertical lift bridges... BRIDGES BRIDGE LIGHTING AND OTHER SIGNALS § 118.85 Lights on vertical lift bridges. (a) Lift span lights. The vertical lift span of every vertical lift bridge shall be lighted so that the center of the...

  13. 23 CFR 650.809 - Movable span bridges.

    Science.gov (United States)

    2010-04-01

    ... 23 Highways 1 2010-04-01 2010-04-01 false Movable span bridges. 650.809 Section 650.809 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION ENGINEERING AND TRAFFIC OPERATIONS BRIDGES, STRUCTURES, AND HYDRAULICS Navigational Clearances for Bridges § 650.809 Movable span bridges. A fixed bridge...

  14. 23 CFR 650.807 - Bridges requiring a USCG permit.

    Science.gov (United States)

    2010-04-01

    ... improvement or construction of a bridge over navigable waters except for the exemption exercised by FHWA in... 23 Highways 1 2010-04-01 2010-04-01 false Bridges requiring a USCG permit. 650.807 Section 650.807... BRIDGES, STRUCTURES, AND HYDRAULICS Navigational Clearances for Bridges § 650.807 Bridges requiring a USCG...

  15. 23 CFR 650.409 - Evaluation of bridge inventory.

    Science.gov (United States)

    2010-04-01

    ... 23 Highways 1 2010-04-01 2010-04-01 false Evaluation of bridge inventory. 650.409 Section 650.409... Evaluation of bridge inventory. (a) Sufficiency rating of bridges. Upon receipt and evaluation of the bridge inventory, a sufficiency rating will be assigned to each bridge by the Secretary in accordance with the...

  16. A one-step separation of human serum high density lipoproteins 2 and 3 by rate-zonal density gradient ultracentrifugation in a swinging bucket rotor

    NARCIS (Netherlands)

    Groot, P.H.E.; Scheek, L.M.; Havekes, L.; Noort, W.L. van; Hooft, F.M. van 't

    1982-01-01

    A method was developed for the separation of the high density lipoprotein subclasses HDL2 and HDL3 from human serum. Six serum samples are fractionated in a single-step ultracentrifugal procedure using the Beckman (SW-40) swinging bucket rotor. The method is based on a difference in flotation rate

  17. Is the modified Tardieu scale in semi-standing position better associated with knee extension and hamstring activity in terminal swing than the supine Tardieu?

    NARCIS (Netherlands)

    Faber, I.R.; Nienhuis, B.; Rijs, N.P.; Geurts, A.C.H.; Duysens, J.E.J.

    2008-01-01

    The aim of this study was to investigate whether the modified Tardieu scale (MTS) in a semi-standing position, used for the assessment of hamstrings spasticity, was better associated with knee extension and hamstrings activity in terminal swing than the MTS in a supine position in children with

  18. A New Limb Movement Detector Enabling People with Multiple Disabilities to Control Environmental Stimulation through Limb Swing with a Gyration Air Mouse

    Science.gov (United States)

    Shih, Ching-Hsiang; Chang, Man-Ling; Shih, Ching-Tien

    2010-01-01

    This study assessed whether two persons with multiple disabilities would be able to control environmental stimulation using limb swing with a gyration air mouse and a newly developed limb movement detection program (LMDP, i.e., a new software program that turns a gyration air mouse into a precise limb movement detector). The study was performed…

  19. A bridge to advanced mathematics

    CERN Document Server

    Sentilles, Dennis

    2011-01-01

    This helpful workbook-style ""bridge"" book introduces students to the foundations of advanced mathematics, spanning the gap between a practically oriented calculus sequence and subsequent courses in algebra and analysis with a more theoretical slant. Part 1 focuses on logic and number systems, providing the most basic tools, examples, and motivation for the manner, method, and concerns of higher mathematics. Part 2 covers sets, relations, functions, infinite sets, and mathematical proofs and reasoning. Author Dennis Sentilles also discusses the history and development of mathematics as well a

  20. Buddha and the bridging relations.

    Science.gov (United States)

    Banerjee, Rahul

    2008-01-01

    The chapter reviews a classical Indian model of consciousness found in the Abhidhamma, a collection of seven treatises in the Pali Canon Tipitaka. The model was based on observations made during advanced vipassana practice, a first-person method taught by the Buddha. The climax of the model consists in the elucidation of 24 'Bridging Relations' causally linking the stream of consciousness, its contents and associated physical events. Review of such a model based on a specialized first-person technique could prove to be a resource of useful ideas providing directions for further research.

  1. Nanoclusters a bridge across disciplines

    CERN Document Server

    Jena, Purusottam

    2010-01-01

    This comprehensive book on Nanoclusters comprises sixteen authoritative chapters written by leading researchers in the field. It provides insight into topics that are currently at the cutting edge of cluster science, with the main focus on metal and metal compound systems that are of particular interest in materials science, and also on aspects related to biology and medicine. While there are numerous books on clusters, the focus on clusters as a bridge across disciplines sets this book apart from others. Delivers cutting edge coverage of cluster science Covers a broad range of topics in

  2. Use of Real‐Time GNSS‐RF Data to Characterize the Swing Movements of Forestry Equipment

    Directory of Open Access Journals (Sweden)

    Ryer M. Becker

    2017-02-01

    Full Text Available The western United States faces significant forest management challenges after severe bark beetle infestations have led to substantial mortality. Minimizing costs is vital for increasing the feasibility of management operations in affected forests. Multi‐transmitter Global Navigation Satellite System (GNSS‐radio frequencies (RF technology has applications in the quantification and analysis of harvest system production efficiency and provision of real‐time operational machine position, navigation, and timing. The aim of this study was to determine the accuracy with which multi‐transmitter GNSS‐RF captures the swinging and forwarding motions of ground based harvesting machines at varying transmission intervals. Assessing the accuracy of GNSS in capturing intricate machine movements is a first step toward development of a real‐time production model to assist timber harvesting of beetle‐killed lodgepole pine stands. In a complete randomized block experiment with four replicates, a log loader rotated to 18 predetermined angles with GNSS‐RF transponders collecting and sending data at two points along the machine boom (grapple and heel rack and at three transmission intervals (2.5, 5.0, and 10.0 s. The 2.5 and 5.0 s intervals correctly identified 94% and 92% of cycles at the grapple and 92% and 89% of cycles at the heel, respectively. The 2.5 s interval successfully classified over 90% of individual cycle elements, while the 5.0 s interval returned statistically similar results. Predicted swing angles obtained the highest level of similarity to observed angles at the 2.5 s interval. Our results show that GNSS‐RF is useful for realtime, model‐based analysis of forest operations, including woody biomass production logistics.

  3. COMPARISON OF THE TRADITIONAL, SWING, AND CHICKEN WING VOLLEYBALL BLOCKING TECHNIQUES IN NCAA DIVISION I FEMALE ATHLETES

    Directory of Open Access Journals (Sweden)

    Taubi J. Neves

    2011-09-01

    Full Text Available In volleyball, blocking is highly correlated with team success. The identification of specific techniques that produce a more successful block would be helpful knowledge for coaches and players. This study compared the traditional, swing, and "chicken wing" blocking techniques in combination with the running step footwork pattern in order to determine which technique enabled athletes to perform a more effective block. High-speed videography (7 cameras, Vicon Motion Analysis System was used to capture the blocking movements of thirteen female NCAA Division I athletes (age = 19.4 ± 1.19 years, height = 1.82 ± 0.08 m, mass = 70.63 ± 7.96 kg, and years of participation at the collegiate level = 2.23 ± 1.17 years. Each player was familiar with each blocking technique. Reflective markers were placed on the players and in randomized order the players performed 3 blocking trials of each technique. The following dependent variables were assessed: The time it took the athletes to get off the ground and get their hands above (vertically the net was calculated. The distance the hand reached over the net or hand penetration (displacement between the net and finger in the anterior and vertical planes was also measured. Lastly, jump height was calculated. Repeated measures ANOVA and post-hoc comparisons were done (α = 0.05. There was no significant difference in the main effect for time to get off the ground (p > 0.05. There was a significant difference in the time to get the hands above the net (p < 0.05. The swing block was best for jump height (p <.001 and hand penetration (p < 0.05. These results can help coaches and players decide which blocking technique will benefit them most as a blocking team and as individual blockers

  4. Advanced bridge safety initiative : FRP flexural retrofit for concrete slab bridges - task 4 deliverables.

    Science.gov (United States)

    2014-06-01

    Concrete slab bridges are being examined as part of the MaineDOT Advanced Bridge Safety Initiative. Under Tasks : 1 3 a finite element analysis program is developed, validated and applied to twenty bridges. : Task 4 investigates and develops a no...

  5. Field performance of timber bridges. 15, Pueblo County, Colorado, stress-laminated deck bridge

    Science.gov (United States)

    L. E. Hislop

    The Pueblo County 204B bridge was constructed in March 1990 in Pueblo, Colorado, as a demonstration bridge under the USDA Forest Service Timber Bridge Initiative. The stress-laminated deck superstructure is approximately 10 m long, 9 m wide, and 406 mm deep, with a skew of 10 degrees. Performance monitoring was conducted for 3 years, beginning at...

  6. Light-weight aluminium bridges and bridge decks. An overview of recent applications

    NARCIS (Netherlands)

    Maljaars, J.; Soetens, F.; Kluyver, D. de

    2008-01-01

    The last decades have shown a large increase in the application of aluminium alloys for light-weight bridges. For bridge construction, aluminium alloys have some specific advantages, but also some points of attention. This paper deals with some recent projects of aluminium bridges, and for these

  7. 49 CFR 236.312 - Movable bridge, interlocking of signal appliances with bridge devices.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Movable bridge, interlocking of signal appliances with bridge devices. 236.312 Section 236.312 Transportation Other Regulations Relating to... SYSTEMS, DEVICES, AND APPLIANCES Interlocking Standards § 236.312 Movable bridge, interlocking of signal...

  8. A bridge with a view, a view with a bridge : Identifying design considerations for bridges to strengthen regional identity

    NARCIS (Netherlands)

    Smits, J.E.P.; van der Hoeven, F.D.

    2015-01-01

    This paper discusses design considerations for creating high quality infrastructural artefacts with an emphasis on bridges. The authors pursue a design study and analysis approach to highlight the specifics of infrastructure design for regional identity, based on their own work on a bridge

  9. Bridging history and social psychology

    DEFF Research Database (Denmark)

    Glaveanu, Vlad Petre; Yamamoto, Koji

    2012-01-01

    This special issue aims to bridge history and social psychology by bringing together historians and social psychologists in an exercise of reading and learning from each other’s work. This interdisciplinary exercise is not only timely but of great importance for both disciplines. Social psycholog......This special issue aims to bridge history and social psychology by bringing together historians and social psychologists in an exercise of reading and learning from each other’s work. This interdisciplinary exercise is not only timely but of great importance for both disciplines. Social...... psychologists can benefit from engaging with historical sources by being able to contextualise their findings and enrich their theoretical models. It is not only that all social and psychological phenomena have a history but this history is very much part of present-day and future developments. On the other...... hand historians can enhance their analysis of historical sources by drawing upon the conceptual tools developed in social psychology. They can “test” these tools and contribute to their validation and enrichment from completely different perspectives. Most important, as contributions to this special...

  10. Developing a Tele-Robotic Platform for Bridge Inspection

    Science.gov (United States)

    2011-05-01

    There are many bridges in Virginia with high traffic volumes or difficult access conditions which make these bridges difficult and expensive to inspect. In addition, the inspection of many bridges exposes the inspectors to hazardous conditions such a...

  11. Real time assessment of dynamic loads on bridges.

    Science.gov (United States)

    2013-05-01

    Highway bridges are an important class of civil structures that are subject to continuously : acting and varying dynamic loads due to traffic. A large number of highway bridges in the US : (bridges on interstate highways or state highways which have ...

  12. Final report bridge design system analysis and modernization.

    Science.gov (United States)

    2016-09-27

    The Bridge Design System (BDS) is an in-house software program developed by the Michigan Department of Transportations : (MDOT) Bridge Design Unit. The BDS designs bridges according to the required specifications, and outputs corresponding design ...

  13. Load ratings for standard bridges : final report, October 2008.

    Science.gov (United States)

    2008-10-01

    A load rating states the load in tons which a vehicle can impose on a bridge. Changes in guidelines, standards, and customary uses of bridges require analyses of bridges to be updated and reevaluated.

  14. Verification of Texas superheavy load criteria for bridges.

    Science.gov (United States)

    2011-11-01

    This report evaluates TxDOT criteria for the superheavy loads that trigger bridge analyses to determine : whether the criteria adequately protects Texas bridges. Researchers used solid modeling calibrated with a : bridge test of a 3-span continuous s...

  15. Response modification for enhanced operation and safety of bridges.

    Science.gov (United States)

    2011-08-01

    This report shows that safe extension of the service life of existing bridge structures is possible through bridge : health monitoring and structural response modification. To understand bridge health monitoring and structural : response modification...

  16. The effect of bridge deck design methodology on crack control.

    Science.gov (United States)

    2010-01-30

    At present, the Idaho Transportation Department (ITD) Bridge Design Manual allows engineers to use the AASHTO empirical method to : design concrete bridge decks. However, the ITD Bridge Section would like to compare their design practices to those em...

  17. Long-term behavior of integral abutment bridges : [technical summary].

    Science.gov (United States)

    2011-01-01

    Integral abutment bridges, a type of jointless bridge, are the construction option of choice when designing highway bridges in many parts of the country. Rather than providing an expansion joint to separate the substructure from the superstructure to...

  18. Design aids of NU I-girders bridges.

    Science.gov (United States)

    2010-05-01

    Precast prestressed concrete I-Girder bridges have become the most dominant bridge system in the United States. In the early design : stages, preliminary design becomes a vital first step in designing an economical bridge. Within the state of Nebrask...

  19. An expert system for the esthetic rating of bridges.

    Science.gov (United States)

    1990-01-01

    The expert system presented should facilitate the in-depth analysis of bridge esthetics and encourage high standards for the appearance of bridges. The procedure described systematically evaluates features of a target bridge in relation to a similar ...

  20. Implementation of sustainability in bridge design, construction and maintenance.

    Science.gov (United States)

    2012-12-01

    The focus of this research is to develop a framework for more sustainable design and construction : processes for new bridges, and sustainable maintenance practices for existing bridges. The framework : includes a green rating system for bridges. The...

  1. 0-6722 : spread prestressed concrete slab beam bridges.

    Science.gov (United States)

    2014-08-01

    The Texas Department of Transportation uses : precast prestressed concrete slab beam bridges for : shorter-span bridges of approximately 3050 ft in : length. Conventional slab beam bridges have slab : beams placed immediately adjacent to one anoth...

  2. History of cable-stayed bridges

    DEFF Research Database (Denmark)

    Gimsing, Niels Jørgen

    1999-01-01

    The principle of supporting a bridge deck by inclined tension members leading to towers on either side of the span has been known for centuries. However, the real development of cable-stayed bridges did not begin before the 1950s. Since then the free span has been increased from 183 m...

  3. Shear assessment of reinforced concrete slab bridges

    NARCIS (Netherlands)

    Lantsoght, E.O.L.; Van der Veen, C.; Walraven, J.C.; De Boer, A.

    2013-01-01

    The capacity of reinforced concrete solid slab bridges in shear is assessed by comparing the design beam shear resistance to the design value of the applied shear force due to the permanent actions and live loads. Results from experiments on half-scale continuous slab bridges are used to develop a

  4. Lifetime Reliability Assessment of Concrete Slab Bridges

    DEFF Research Database (Denmark)

    Thoft-Christensen, Palle

    A procedure for lifetime assesment of the reliability of short concrete slab bridges is presented in the paper. Corrosion of the reinforcement is the deterioration mechanism used for estimating the reliability profiles for such bridges. The importance of using sensitivity measures is stressed...

  5. Neighborhood Bridges: 2010-2011 Evaluation Report

    Science.gov (United States)

    Ingram, Debra

    2011-01-01

    In 2010-2011, students in twenty-five classrooms from eleven schools in the Minneapolis-Saint Paul metropolitan area participated in The Children's Theatre Company's Neighborhood Bridges (Bridges) program. The Children's Theatre Company contracted with the University of Minnesota's Center for Applied Research and Educational Improvement (CAREI) to…

  6. Rapid replacement/construction of bridges.

    Science.gov (United States)

    2012-11-01

    Bridges are a key element of the transportation system because they control system capacity and are normally built at : the highest cost to the system. Once a bridge reaches its useful design service life, it needs to be replaced or : reconstructed i...

  7. Kings Covered Bridge rehabilitation, Somerset County, PA

    Science.gov (United States)

    William J. Collins; David C. Fischetti; Arnold M. Jr. Graton; Len Lichvar; Branden Diehl; James P. Wacker; Ed Cesa; Ed Stoltz; Emory L. Kemp; Samer H. Petro; Leon Buckwalter; John McNamara

    2005-01-01

    Kings Covered Bridge over Laurel Creek in Somerset County, Pennsylvania is approximately 114-foot clear span multiple Kingpost Truss with nail-laminated arches. This timber bridge is historically significant because it retains its original features of the 1860’s since the 1930s when it was spared from modernization by the construction of an adjacent steel highway...

  8. Disturbance indicator benchmark for urban bridge construction

    NARCIS (Netherlands)

    Brouwer, J.; Vogel, R.; Thodesen, C.

    2013-01-01

    European bridges are today in a state of particular concern with over 50% of European urban bridges being more than 40 years old and thus requiring considerable maintenance or possibly even replacement [1]. This means that interventions in the present infrastructure have to be made while ensuring

  9. Analysis of Biaxially Stressed Bridge Deck Plates

    DEFF Research Database (Denmark)

    Jönsson, Jeppe; Bondum, Tommi Højer

    2012-01-01

    The ultimate state analysis of bridge deck plates at the intersection zone between main girders and transverse beams is complicated by biaxial membrane stresses, which may be in compression or tension in either direction depending on the bridge configuration and the specific location. This paper...

  10. Construction of crack-free bridge decks.

    Science.gov (United States)

    2017-04-01

    This serves as the final report on Transportation Pooled-Fund Program Project No. TPF-5(174), Construction : of Crack-Free Bridge Decks. The goal of the study was to implement the most cost-effective techniques for : improving bridge deck life ...

  11. Re-Assessment of Concrete Bridges

    DEFF Research Database (Denmark)

    Thoft-Christensen, Palle

    In this paper two aspects of re-assessment of the reliability of concrete bridges are discussed namely modelling of the corrosion of reinforcement and updating of uncertain variables. The main reason for deterioration of concrete bridges is corrosion of the reinforcement. Therefore, modelling...

  12. Bridges Over Troubled Waters: Theoretical Linguistics And ...

    African Journals Online (AJOL)

    This paper tries to construct a bridge between the concerns of theoretical linguistics and those of multilingualism and code-switching (CS) research. It argues that the primary special point of interaction between these fields lies in the question of potential equivalence between elements or categories, bridging across ...

  13. Standard plans for southern pine bridges

    Science.gov (United States)

    P. D. Hilbrich Lee; M. A. Ritter; M. H. Triche

    1995-01-01

    The development of standardized timber bridge plans and specifications is a key element in improving design and construction practices. The bridge plans presented were developed as a cooperative effort between the USDA Forest Service, Forest Products Laboratory (FPL); the University of Alabama; and the Southern Pine Council and are the first step in developing...

  14. Debris mitigation methods for bridge piers.

    Science.gov (United States)

    2012-06-01

    Debris accumulation on bridge piers is an on-going national problem that can obstruct the waterway openings at bridges and result in significant erosion of stream banks and scour at abutments and piers. In some cases, the accumulation of debris can a...

  15. Optimum Maintenance Strategies for Highway Bridges

    DEFF Research Database (Denmark)

    Frangopol, Dan M.; Thoft-Christensen, Palle; Das, Parag C.

    As bridges become older and maintenance costs become higher, transportation agencies are facing challenges related to implementation of optimal bridge management programs based on life cycle cost considerations. A reliability-based approach is necessary to find optimal solutions based on minimum...... expected life-cycle costs or maximum life-cycle benefits. This is because many maintenance activities can be associated with significant costs, but their effects on bridge safety can be minor. In this paper, the program of an investigation on optimum maintenance strategies for different bridge types...... is described. The end result of this investigation will be a general reliability-based framework to be used by the UK Highways Agency in order to plan optimal strategies for the maintenance of its bridge network so as to optimize whole-life costs....

  16. New conceptual design of portable bamboo bridge for emergency purposes

    Science.gov (United States)

    Musthaffa, A. A.; Nor, N. M.; Yusof, M. A.; Yuhazri, M. Y.

    2018-02-01

    Portable bridges serve as routes for troops during the military operations and the disaster relief operation. Nowadays, bamboo has been regarded as one of the alternative construction materials for building and bridge structures. This paper presents the conceptual design of the portable bridge. Several types of portable bridges and bamboo bridges are reviewed in the current work. The characteristics, capability and method of construction of each bridge are discussed. Finally, the conceptual of the portable bamboo bridge for emergency purposes is presented. The idea of producing portable bridge is proposed in the current work as it is crucial for providing route for communities affected by natural disasters.

  17. Root coverage with bridge flap

    Directory of Open Access Journals (Sweden)

    Pushpendra Kumar Verma

    2013-01-01

    Full Text Available Gingival recession in anterior teeth is a common concern due to esthetic reasons or root sensitivity. Gingival recession, especially in multiple anterior teeth, is of huge concern due to esthetic reasons. Various mucogingival surgeries are available for root coverage. This case report presents a new bridge flap technique, which allows the dentist not only to cover the previously denuded root surfaces but also to increase the zone of attached gingiva at a single step. In this case, a coronally advanced flap along with vestibular deepening technique was used as root coverage procedure for the treatment of multiple recession-type defect. Here, vestibular deepening technique is used to increase the width of the attached gingiva. The predictability of this procedure results in an esthetically healthy periodontium, along with gain in keratinized tissue and good patient′s acceptance.

  18. Building bridges … and accelerators

    CERN Document Server

    2009-01-01

    Lyn Evans, the LHC project leader, was awarded an honorary doctorate from the University of Geneva (UNIGE) to celebrate his role not just in building accelerators, but also in building bridges between nations. He was one of four notables honoured at the event on Friday 5 June, coinciding with the University’s 450th Anniversary. Lyn Evans arriving at the ceremony with Archbishop Desmond Tutu. "It was a big surprise when I found out I’d been nominated," recounts Evans, "but it was an even bigger surprise to find out with whom I’d been nominated". At the ceremony Evans was awarded the honorary doctorate along with three others: Archbishop Desmond Tutu, who was acclaimed for his fight against apartheid in South Africa, Mary Robinson, first woman president of Ireland and former United Nations’ high commissioner of human rights, and Pascal Lamy, Director-General of the World Trade Organization. The award ceremony, known as the �...

  19. Lava zirconia crowns and bridges.

    Science.gov (United States)

    Suttor, D

    2004-01-01

    Ceramic restorations--suitable for the anterior as well as the posterior region, simultaneously satisfying the demand for high strength, longevity, and esthetics--are an increasingly important field for the dental professional. Because of its outstanding mechanical properties and esthetics with a proven track record in other industrial areas, zirconium oxide (zirconia) is emerging in the dental industry. As the manufacturing method of choice, CAD/CAM is important for the dental laboratory; however, in the final analysis, the primary focus will be on the material properties and the clinical performance of the result of the CAD/CAM process--in this case, zirconia crowns and bridges. This is especially true since some concepts do not require the acquisition of a CAD/CAM system at all.

  20. Pharmacological bridge to cardiac transplantation.

    Science.gov (United States)

    Loisance, D; Dubois Rande, J L; Deleuze, P H; Hillion, M L; Duval, A M; Tavolaro, O; Romano, P; Castaigne, A; Tarral, A; Cachera, J P

    1989-01-01

    From September 1985 to August 1988, 32 patients were referred from various intensive care units throughout Paris for urgent cardiac transplantation or for a mechanical bridge to transplantation. At time of admission, under maximal sympathomimetic therapy, the cardiac index (CI) was 1.81 +/- 0.26 l/min per m2, the pulmonary capillary wedge pressure (PCWP 31 +/- 7 mmHg), systemic vascular resistances (SVR) 2053 +/- 469 dynes s cm-5. In 25, diuresis was less than 25 ml/h. Five were anuric. Prior to any final decision, a new inotropic agent, enoximone, was infused in addition to previous treatment as a 10 min bolus iv 1.5-2 mg/kg every 8 h. In 3, the situation further deteriorated, leading to a Jarvik 7-70 implantation within 12 h. In 29 however, within 3 h, the Cl increased to 2.69 +/- 0.56 as SVR dropped to 1410 +/- 453 and PCWP to 18 +/- 7. Diuresis increased to more than 100 ml/h in all. This permitted an indepth evaluation of the transplant candidates leading to contraindications to transplantation in 16. Nine patients could be weaned off iv enoximone. Four of these are still living (NYHA class III) with a follow up of 6-17 months. In 11, transplantation was performed within 2 days. Four died within a month, 2 with multiple organ failure. One patient died after 5 months. Six are back to normal life, NYHA class I (follow up 10 months-2.5 years). This protocol suggests that in patients with extreme heart failure, immediate survival may be increased by iv enoximone therapy, permitting a better selection of the recipients, more efficient pre-transplantation intensive care and consequently a decrease in the indications for a temporary mechanical bridge to a staged transplantation.