Development, characterization and testing of tungsten doped DLC coatings for dry rotary swaging

Directory of Open Access Journals (Sweden)

Hasselbruch Henning

2015-01-01

Full Text Available The extensive use of lubricant during rotary swaging is particularly required for a good surface finish of the work piece and the reduction of tool wear. Abandonment of lubricant would improve the ecological process-balance and could also accelerate for further work piece refinements. Also cleaning of the manufactured components becomes obsolete. Thus, a dry machining is highly innovative, consequently new strategies to substitute the lubricant functions become necessary. To encounter the changed tribological conditions due to dry rotary swaging, low friction, tungsten doped, hard DLC coatings and structured surfaces are the most promising approaches. In this work the development of hard coating by means of reactive magnetron sputtering is presented, a promising layer variant is deposited on a set of tools and then tested and investigated in real use.

Basic thermal–mechanical properties and thermal shock, fatigue resistance of swaged + rolled potassium doped tungsten

Energy Technology Data Exchange (ETDEWEB)

Zhang, Xiaoxin; Yan, Qingzhi, E-mail: qzyan@ustb.edu.cn; Lang, Shaoting; Xia, Min; Ge, Changchun

2014-09-15

Highlights: • The potassium doped tungsten grade was achieved via swaging + rolling process. • The cracking threshold of the W–K alloy was in the range of 0.44–0.66 GW/m{sup 2}. • Recrystallization occurred at 0.66–1.1 GW/m{sup 2} during the thermal shock tests. • No cracks emerged during the thermal fatigue tests (0.44 GW/m{sup 2}, 1000 cycles). • Recrystallization occurred after 1000 cycles during the thermal fatigue tests. - Abstract: The potassium doped tungsten (W–K) grade was achieved via swaging + rolling process. The swaged + rolled W–K alloy exhibited acceptable thermal conductivity of 159.1 W/m K and ductile-to-brittle transition temperature of about 873 K while inferior mechanical properties attributed to the coarse pores and small deformation degree. Then the thermal shock, fatigue resistance of the W–K grade were characterized by an electron beam facility. Thermal shock tests were conducted at absorbed power densities varied from 0.22 to 1.1 GW/m{sup 2} in a step of 0.22 GW/m{sup 2}. The cracking threshold was in the range of 0.44–0.66 GW/m{sup 2}. Furthermore, recrystallization occurred in the subsurface of the specimens tested at 0.66–1.1 GW/m{sup 2} basing on the analysis of microhardness and microstructure. Thermal fatigue tests were performed at 0.44 GW/m{sup 2} up to 1000 cycles and no cracks emerged throughout the tests. Moreover, recrystallization occurred after 1000 cycles.

Basic thermal-mechanical properties and thermal shock, fatigue resistance of swaged + rolled potassium doped tungsten

Science.gov (United States)

Zhang, Xiaoxin; Yan, Qingzhi; Lang, Shaoting; Xia, Min; Ge, Changchun

2014-09-01

The potassium doped tungsten (W-K) grade was achieved via swaging + rolling process. The swaged + rolled W-K alloy exhibited acceptable thermal conductivity of 159.1 W/m K and ductile-to-brittle transition temperature of about 873 K while inferior mechanical properties attributed to the coarse pores and small deformation degree. Then the thermal shock, fatigue resistance of the W-K grade were characterized by an electron beam facility. Thermal shock tests were conducted at absorbed power densities varied from 0.22 to 1.1 GW/m2 in a step of 0.22 GW/m2. The cracking threshold was in the range of 0.44-0.66 GW/m2. Furthermore, recrystallization occurred in the subsurface of the specimens tested at 0.66-1.1 GW/m2 basing on the analysis of microhardness and microstructure. Thermal fatigue tests were performed at 0.44 GW/m2 up to 1000 cycles and no cracks emerged throughout the tests. Moreover, recrystallization occurred after 1000 cycles.

Effect of Annealing Temperature on the Corrosion Protection of Hot Swaged Ti-54M Alloy in 2 M HCl Pickling Solutions

Directory of Open Access Journals (Sweden)

El-Sayed M. Sherif

2017-01-01

Full Text Available The corrosion of Ti-54M titanium alloy processed by hot rotary swaging and post-annealed to yield different grain sizes, in 2 M HCl solutions is reported. Two annealing temperatures of 800 °C and 940 °C, followed by air cooling and furnace cooling were used to give homogeneous grain structures of 1.5 and 5 μm, respectively. It has been found that annealing the alloy at 800 °C decreased the corrosion of the alloy, with respect to the hot swaged condition, through increasing its corrosion resistance and decreasing the corrosion current and corrosion rate. Increasing the annealing temperature to 940 °C further decreased the corrosion of the alloy.

Annealing Effects on Microstructure and Mechanical Properties of Ultrafine-Grained Al Composites Reinforced with Nano-Al2O3 by Rotary Swaging

Science.gov (United States)

Chen, Cunguang; Wang, Wenwen; Guo, Zhimeng; Sun, Chunbao; Volinsky, Alex A.; Paley, Vladislav

2018-03-01

Microstructure evolution and variations in mechanical properties of Al-Al2O3 nanocomposite produced by powder metallurgy were investigated and compared with commercially pure aluminum (Al-1050) after furnace annealing. Fine gas-atomized Al powder compacts were first sintered in flowing nitrogen, subsequently consolidated into wires by rotary swaging and eventually annealed at 300 and 500 °C for 24 h each. Scanning and transmission electron microscopy with energy-dispersive spectroscopy was utilized to document the microstructure evolution. Rotary swaging was proven to lead to a marked decrease in grain size. After heavy swaging to true deformation degree of φ = 6 and annealing at 500 °C, obvious recrystallization was observed at Al-1050's existing grain boundaries and the crystals began to grow perpendicular to the flow direction. In the Al-Al2O3 nanocomposite, fabricated from d 50 = 6 μm Al powder, recrystallization partially occurred, while grains were still extremely fine. Due to the dual role of fine-grained Al2O3 dispersion strengthening, the nanocomposite showed improved mechanical performance in terms of tensile strength, approximately twice higher than Al-1050 after annealing at 500 °C.

Reduction of Gas Bubbles and Improved Critical Current Density in Bi-2212 Round Wire by Swaging

CERN Document Server

Jiang, J; Huang, Y; Hong, S; Parrell, J; Scheuerlein, C; Di Michiel, M; Ghosh, A; Trociewitz, U; Hellstrom, E; Larbalestier, D

2013-01-01

Bi-2212 round wire is made by the powder-in-tube technique. An unavoidable property of powder-in-tube conductors is that there is about 30% void space in the as-drawn wire. We have recently shown that the gas present in the as-drawn Bi-2212 wire agglomerates into large bubbles and that they are presently the most deleterious current limiting mechanism. By densifying short 2212 wires before reaction through cold isostatic pressing (CIPping), the void space was almost removed and the gas bubble density was reduced significantly, resulting in a doubled engineering critical current density (JE) of 810 A/mm2 at 5 T, 4.2 K. Here we report on densifying Bi-2212 wire by swaging, which increased JE (4.2 K, 5 T) from 486 A/mm2 for as-drawn wire to 808 A/mm2 for swaged wire. This result further confirms that enhancing the filament packing density is of great importance for making major JE improvement in this round-wire magnet conductor.

Effect of swaging on the 1000 C compressive slow plastic flow characteristics of the directionally solidified eutectic alloy gamma/gamma prime-alpha

Science.gov (United States)

Whittenberger, J. D.; Wirth, G.

1983-01-01

Swaging between 750 and 1050 C has been investigated as a means to introduce work into the directionally solidified eutectic alloy gamma/gamma prime-alpha (Ni-32.3 wt percent Mo-6.3 wt percent Al) and increase the elevated temperature creep strength. The 1000 C slow plastic compressive flow stress-strain rate properties in air of as-grown, annealed, and worked nominally 10 and 25 percent materials have been determined. Swaging did not improve the slow plastic behavior. In fact large reductions tended to degrade the strength and produced a change in the deformation mechanism from uniform flow to one involving intense slip band formation. Comparison of 1000 C tensile and compressive strength-strain rate data reveals that deformation is independent of the stress state.

Influence of the pressure holding time on strain generation in fuel injection lines

International Nuclear Information System (INIS)

Basara, Adis; Alt, Nicolas; Schluecker, Eberhard

2011-01-01

An influence of the pressure holding time on residual strain generation during the autofrettage process was studied experimentally for the first time in the present work. It is the state of the art that fuel injection lines are held at the autofrettage pressure for only a few seconds in an industrial production. In doing so, it is assumed that a desirable residual stress-strain pattern is generated. However, the results of the experimental investigations outlined in this work indicated that completion of the plastic deformation caused by the autofrettage process and generation of the desirable stress-strain pattern require a much longer period. As shown, a third-order polynomial equation best described the interdependence between the time required for the completion of the process, the corresponding autofrettage pressure and the generated strain state. The method presented can be used as a tool for the determination of the optimal autofrettage process parameters in industrial production of fuel injection lines.

Ultrafine-Grained Precipitation Hardened Copper Alloys by Swaging or Accumulative Roll Bonding

Directory of Open Access Journals (Sweden)

Igor Altenberger

2015-05-01

Full Text Available There is an increasing demand in the industry for conductive high strength copper alloys. Traditionally, alloy systems capable of precipitation hardening have been the first choice for electromechanical connector materials. Recently, ultrafine-grained materials have gained enormous attention in the materials science community as well as in first industrial applications (see, for instance, proceedings of NANO SPD conferences. In this study the potential of precipitation hardened ultra-fine grained copper alloys is outlined and discussed. For this purpose, swaging or accumulative roll-bonding is applied to typical precipitation hardened high-strength copper alloys such as Corson alloys. A detailed description of the microstructure is given by means of EBSD, Electron Channeling Imaging (ECCI methods and consequences for mechanical properties (tensile strength as well as fatigue and electrical conductivity are discussed. Finally the role of precipitates for thermal stability is investigated and promising concepts (e.g. tailoring of stacking fault energy for grain size reduction and alloy systems for the future are proposed and discussed. The relation between electrical conductivity and strength is reported.

Mechanical characterization of Ti-12Mo-13Nb alloy for biomedical application hot swaged and aged

Energy Technology Data Exchange (ETDEWEB)

Gabriel, Sinara Borborema; Rezende, Monica Castro; Almeida, Luiz Henrique de, E-mail: sinara@metalmat.ufrj.br [Universidade Federal do Rio de Janeiro (UFRJ), Rio de Janeiro, RJ (Brazil). Departamento de Engenharia Metalurgica e de Materiais; Dille, Jean [Universite Libre de Bruxelles, Brussels (Belgium); Mei, Paulo [Universidade Estadual de Campinas (UNICAMP), Campinas, SP (Brazil). Departamento de Engenharia Mecanica; Baldan, Renato; Nunes, Carlos Angelo [Universidade de Sao Paulo (USP), Lorena, SP (Brazil). Departamento de Engenharia de Materiais

2015-07-01

Beta titanium alloys were developed for biomedical applications due to the combination of its mechanical properties including low elasticity modulus, high strength, fatigue resistance, good ductility and with excellent corrosion resistance. With this perspective a metastable beta titanium alloy Ti-12Mo-13Nb was developed with the replacement of both vanadium and aluminum from the traditional alloy Ti-6Al-4V. This paper presents the microstructure, mechanical properties of the Ti-12Mo-13Nb hot swaged and aged at 500 deg C for 24 h under high vacuum and then water quenched. The alloy structure was characterized by X-ray diffraction and transmission electron microscopy. Tensile tests were carried out at room temperature. The results show a microstructure consisting of a fine dispersed α phase in a β matrix and good mechanical properties including low elastic modulus. The results indicate that Ti-12Mo-13Nb alloy can be a promising alternative for biomedical application. (author)

Characterization of consolidated rapidly solidified Cu-Nb ribbons

International Nuclear Information System (INIS)

Ebrahimi, F.; Henne, M.L.C.

1997-01-01

Copper-niobium ribbons produced by melt-spinning were compacted by swaging and consolidated using HIPping. Final processing to obtain in-situ composites was done by swaging. The strength of the composite is discussed in terms of the composition and morphology of the niobium phase as evaluated using electron microscopy techniques

Tungsten heavy metal alloys relations between the crystallographic texture and the internal stress distribution

International Nuclear Information System (INIS)

Nicolas, G.; Voltz, M.

2001-01-01

Quite often the W-Ni-Fe-Co heavy alloys are subjected to a thermomechanical processing of swaging and aging in order to obtain the highest possible level of resistance. Within the framework of this plastic deformation on cylindrical parts, the swaging leads to the distribution of morphological and crystallographic texture as well as specific internal stresses. The resulting mechanical characteristics are correlated to structural and sub-structural variations. (author)

The influence of recrystallization annealing and the state of stress on tungsten formability

International Nuclear Information System (INIS)

Greger, M.

1995-01-01

The submitted deals with the prediction of strain limits regarding the swaging procedures. An appearance of inhomogeneous localities and defect inward the forged bodies is assumed to be affected by plasticity of applied tungsten being strictly determined by chemical composition and thermomechanical conditions of the forging process. Chosen operation of swaging procedure were analysed in terms of hypothesis of maximum admissible strain, the calculated value of which at the critical area of forging had to be lesser than the strain limit

Scaleup of powder metallurgy processed Nb-Al multifilamentary wire

International Nuclear Information System (INIS)

Thieme, C.; Foner, S.; Otubo, J.; Pourrahimi, S.; Schwartz, B.; Zhang, H.

1983-01-01

Power metallurgy processed Nb-Al superconducting wires were fabricated from billets up to 45 mm o.d. with nominal areal reduction ratios, R, up to 2 X 10 5 , Nb powder sizes from 40 to 300 μm from various sources, Al powder sizes from 9 to 75 μm, Al concentrations from 3 to 25 wt % Al and with a wide range of heat treatments. All the compacts used tap density powder in a Cu tube and swaging and/or rod rolling and subsequent wire drawing. Both single strand and bundled wires were made. Overall critical current densities, J /SUB c/, of 2 X 10 4 A/cm 2 at 14 T and 10 4 A/cm 2 at 16 T were achieved for 6 to 8 wt % Al in Nb

Microstructural Development and Control in Liquid Phase Sintering; Processing, Structures and Properties of Cold Worked Metal Matrix Composites

Science.gov (United States)

1984-06-03

between them in a composite develops in a manner consistent with the macroscopic axisymmetric deformation of wire drawing or swaging. Additionally, for...spacing) V 0 bo :vsii~f:- nikel omposit’es 0.5 -~ ................................*. . C pper-7chrorhium c2o * - - 0 0 C -io~omposites ~ :13 Nickeil

Metallurgical processing and properties of multifilamentary V3Ga composite wires

International Nuclear Information System (INIS)

Howe, D.G.; Weinman, L.S.

1976-01-01

Multifilamentary composite wires of V - 6.1 at. percent Ga filaments in a Cu-17.5 at. percent Ga matrix were fabricated. High purity V and Ga were arc melted and cast to form an alloy rod. High purity Cu and Ga were induction melted and also cast as an alloy rod. The alloy rods were reduced in diameter by swaging. The larger diameter Cu - Ga matrix rod was drilled with 19 holes which terminated within the matrix-rod. The holes served as receptacles for 19 V-Ga rods which were inserted into the matrix. The composite assembly was evacuated under high vacuum and sealed by an electron beam weld. The composite was then reduced in diameter through swaging and wire drawing to 0.032-in. dia wire. V 3 Ga layers at the filament/matrix interface were formed through an isothermal solid-state reaction. Growth rates for V 3 Ga are strongly influenced by alloy composition and formation temperature, with more rapid growth occurring in composite wires with higher Ga contents. Improved critical current densities (J/sub c/) resulted from lower formation temperatures, J/sub c/ values of over 1 x 10 6 A/cm 2 in a transverse magnetic field of 100 kG were obtained in the multifilamentary composite wire. 9 figs

Influence of cold-working and subsequent heat-treatment on young's modulus and strength of Co-Ni-Cr-Mo alloy

International Nuclear Information System (INIS)

Otomo, Takuma; Matsumoto, Hiroaki; Chiba, Akihiko; Nomura, Naoyuki

2009-01-01

Changes in Young's modulus of the Co-31 mass%Ni-19 mass%Cr-10 mass%Mo alloy (Co-Ni based alloy) with cold-swaging, combined with heat-treatment at temperatures from 673 to 1323 K, was investigated to enhance the Young's modulus of Co-Ni based alloy. After cold-swaging, the Co-Ni based alloy, forming fiber deformation texture, shows the Young's modulus of 220 GPa. Furthermore, after ageing the cold-swaged alloy at temperature from 673 to 1323 K, the Young's modulus increased to 230 GPa, accompanied by a decrease in the internal fiction and an increase in the tensile strength. This suggests that the increment in Young's modulus is caused by a moving of the vacancies to the dislocation cores and a continuous locking of the dislocations along their entire length with solute atoms (trough model). By annealing at 1323 K after cold swaging, Young's modulus slightly increased to 236 GPa. On the other hand, the tensile strength decreases to almost the same value as that before cold swaging due to recrystallization. These results suggest that the Young's modulus and the strength in the present alloy are simultaneously enhanced by the continuous dislocation locking during aging as well as the formation of fiber deformation texture. (author)

Charging material into a container and closing the container

International Nuclear Information System (INIS)

Critchley, R.J.; Oldham, S.R.

1989-01-01

Radioactive waste material is passed from a cell through a port into a storage drum which has a mouth with a removable lid. A port door includes an electromagnet to hold the lid to the door and both are moved into the cell by a pneumatic cylinder to allow loading of the drum and after re-closure of door and lid swaging tools operate to deform the lid to form one or more lips which engage under the margin around mouth to resist separation of the lid from the drum. Seals are provided. The swaging tools, or a single swaging tool, can be rotatably mounted on the port door. (author)

Application of radiation technology to sewage sludge processing: A review

International Nuclear Information System (INIS)

Wang Jianlong; Wang Jiazhuo

2007-01-01

Sewage sludge is unwanted residual solid wastes generated in wastewater treatment and its management is one of the most critical environmental issues of today. The treatment and disposal of sludge contribute a considerable proportion of the cost for running a wastewater treatment plant. The increasing amount of swage sludge and more and more legislative regulation of its disposal have stimulated the need for developing new technologies to process sewage sludge efficiently and economically. One ideal consideration is to recycle it after proper treatment. Radiation technology is regarded to be a promising alternative for its high efficiency in pathogen inactivation, organic pollutants oxidation, odor nuisance elimination and some other characteristics enhancement, which will facilitate the down-stream process of sludge treatment and disposal. Here we present a brief review of application of radiation technology on sewage sludge processing. Some basic information of two currently available irradiation systems and fundamental radiation chemistry are introduced firstly; then the world-wide application of this promising technology is reviewed; various effects of radiation on sludge is discussed in detail; and some concluding remarks are given and some future directions are also proposed

Fall meeting 2004: information conference on engines. Final and interim reports of the research centres; Herbsttagung 2004: Informationstagung Motoren. Abschluss- und Zwischenberichte der Forschungsstellen

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-07-01

The Proceedings (volume R526, 2004) of the Information Conference on Engines which has been held on the 23rd September 2004 in Pforzheim/Germany, contains ten final and interim reports. The subjects of the contributions presented were as follow: particulate filter with NOx storage coating; cause study on damage-relevant knocking combustion; spray wall interaction; binaural transfer path analysis synthesis; acoustical optimized sealing-systems on engine acoustics; working process caused gas exchange noise; knowledge based diesel engine optimization; frontal press fit assemblies; case hardening and autofrettage; oil condition sensor (orig.)

Oxide dispersion strengthened ferritic alloys. 14/20% chromium: effects of processing on deformation texture, recrystallization and tensile properties

International Nuclear Information System (INIS)

Regle, H.

1994-01-01

The ferritic oxide dispersion strengthened alloys are promising candidates for high temperature application materials, in particular for long life core components of advanced nuclear reactors. The aim of this work is to control the microstructure, in order to optimise the mechanical properties. The two ferritic alloys examined here, MA956 and MA957, are obtained by Mechanical Alloying techniques. They are characterised by quite anisotropic microstructure and mechanical properties. We have investigated the influence of hot and cold working processes (hot extrusion, swaging and cold-drawing) and recrystallization heat treatments on deformation textures, microstructures and tensile properties. The aim was to control the size of the grains and their anisotropic shape, using recrystallization heat treatments. After consolidation and hot extrusion, as-received materials present a extremely fine microstructure with elongated grains and a very strong (110) deformation texture with single-crystal character. At that stage of processing, recrystallization temperature are very high (1450 degrees C for MA957 alloy and 1350 degrees C for MA956 alloy) and materials develop millimetric recrystallized grains. Additional hot extrusion induce a fibre texture. Cold-drawing maintains a fibre texture, but the intensity decreases with increasing cold-work level. For both materials, the decrease of texture intensities correspond to a decrease of the recrystallization temperatures (from 1350 degrees C for a low cold-work level to 750 degrees C for 60 % cold-deformation, case of MA956 alloy) and a refinement of the grain size (from a millimetric size to less than an hundred of micrometer). Swaging develop a cyclic component where the intensity increases with increasing deformation in this case, the recrystallization temperature remains always very high and the millimetric grain size is slightly modified, even though cold-work level increases. Technologically, cold-drawing is the only way

Anisotropic nature of radially strained metal tubes

Science.gov (United States)

Strickland, Julie N.

yield strength to calculate these ratings. I set out to characterize the anisotropic nature of swaged metal. As expected, the tensile tests showed a difference between the axial and transverse tensile strength. The correlation was 12% difference in yield strength in the axial and transverse directions for strained material and 9% in strained and aged material. This means that the strength of the metal in the hoop (transverse) direction is approximately 10% stronger than in the axial direction, because the metal was work hardened during the swaging process. Therefore, the metal is more likely to fail in axial tension than in burst or collapse. I presented the findings from the microstructure examination, standard tensile tests, and SEM data. All of this data supported the findings of the mini-tensile tests. This information will help engineers set burst and collapse ratings and allow material scientists to predict the anisotropic characteristics of swaged steel tubes.

The effect of Zr on the microstructure and properties of Ti-35Nb-XZr alloy

Energy Technology Data Exchange (ETDEWEB)

Málek, Jaroslav, E-mail: malek@ujp.cz [UJP PRAHA a.s., Nad Kamínkou 1345, 156 00 Prague-Zbraslav (Czech Republic); Czech Technical University in Prague, Faculty of Mechanical Engineering, Karlovo náměstí 13, 121 35 Praha 2 (Czech Republic); Hnilica, František, E-mail: hnilica@ujp.cz [UJP PRAHA a.s., Nad Kamínkou 1345, 156 00 Prague-Zbraslav (Czech Republic); Veselý, Jaroslav, E-mail: vesely@ujp.cz [UJP PRAHA a.s., Nad Kamínkou 1345, 156 00 Prague-Zbraslav (Czech Republic); Smola, Bohumil, E-mail: smola@met.mff.cuni.cz [Charles University in Prague, Faculty of Mathematics and Physics, KeKarlovu 5, 121 16 Prague 2 (Czech Republic); Kolařík, Kamil, E-mail: kamil.kolarik@email.cz [Czech Technical University in Prague, Faculty of Nuclear Sciences and Physical Engineering, Trojanova 339/13, 120 00 Praha 2 (Czech Republic); Fojt, Jaroslav, E-mail: jaroslav.fojt@vscht.cz [Institute of Chemical Technology, Technická 5, 166 28 Prague (Czech Republic); Vlach, Martin, E-mail: martin.vlach@mff.cuni.cz [Charles University in Prague, Faculty of Mathematics and Physics, KeKarlovu 5, 121 16 Prague 2 (Czech Republic); Kodetová, Veronika [Charles University in Prague, Faculty of Mathematics and Physics, KeKarlovu 5, 121 16 Prague 2 (Czech Republic)

2016-10-15

The demand for biomaterials with high strength, low modulus, excellent biocompatibility and good corrosion resistance has led to the development of new alloys. Zirconium is known as a biocompatible element that can be used for alloying in titanium alloys. The effect of Zr on the mechanical and structural properties of a titanium alloy is studied in this paper. Binary Ti-35Nb alloy has been alloyed with various amounts of Zr (2, 4, 6 or 8 wt%). The specimens were thermo-mechanically processed (hot forged, solution treated 850 °C/0.5 h/water quenched, cold swaged and finally aged (at 400 °C or 450 °C for various periods). Cold-swaged alloys possess tensile strength of about 800 MPa, along with a low Young's modulus (~50 GPa). The elongation of all the alloys is more than 12%. The hardness increased during 400 °C annealing up to 370 HV10. The addition of Zr stabilized the β-phase and supports recrystallization and recovery processes. Corrosion resistance was also increased by the addition of Zr.

Deformation processed Al/Ca nano-filamentary composite conductors for HVDC applications

Science.gov (United States)

Czahor, C. F.; Anderson, I. E.; Riedemann, T. M.; Russell, A. M.

2017-07-01

Efficient long-distance power transmission is necessary as the world continues to implement renewable energy sources, often sited in remote areas. Light, strong, high-conductivity materials are desirable for this application to reduce both construction and operational costs. In this study an Al/Ca (11.5% vol.) composite with nano-filamentary reinforcement was produced by powder metallurgy then extruded, swaged, and wire drawn to a maximum true strain of 12.7. The tensile strength increased exponentially as the filament size was reduced to the sub-micron level. In an effort to improve the conductor’s ability to operate at elevated temperatures, the deformation-processed wires were heat-treated at 260°C to transform the Ca-reinforcing filaments to Al2Ca. Such a transformation raised the tensile strength by as much as 28%, and caused little change in ductility, while the electrical conductivity was reduced by only 1% to 3%. Al/Al2Ca composites are compared to existing conductor materials to show how implementation could affect installation and performance.

Experimental and finite element prediction of bursting pressure in compound cylinders

International Nuclear Information System (INIS)

Majzoobi, G.H.; Farrahi, G.H.; Pipelzadeh, M.K.; Akbari, A.

2004-01-01

Aluminium cylinders with a constant ratio of outer to inner radii, k=2.2, with different diametral interferences and various shrinkage radii were subjected to bursting and autofrettage pressures. Numerical simulations of the compound cylinders were also performed using the finite element code, NISA. The results can predict the optimum shrinkage radius to a reasonable accuracy with the use of finite element analysis. This radius corresponds to the situation when the maximum von-Mises stress at the internal radii of both the inner and outer cylinders become equal. It was shown that the maximum von-Mises stress across the wall of the cylinder is at the minimum at this shrinkage radius. The optimum diametral interference was found to be that which sufficiently brought the contact surface of the inner and outer cylinders to the point of yielding. Should the shrinkage pressure exceed the elastic limit, the pressure capacity of the cylinder will not be improved. The numerical and experimental results show that autofrettage had no effect on the bursting pressure of the thick-walled compound cylinder for the material tested

Thermal Recovery from Cold-Working in Type K Bare-Wire Thermocouples

Science.gov (United States)

Greenen, A. D.; Webster, E. S.

2017-12-01

Cold-working of most thermocouples has a significant, direct impact on the Seebeck coefficient which can lead to regions of thermoelectric inhomogeneity and accelerated drift. Cold-working can occur during the wire swaging process, when winding the wire onto a bobbin, or during handling by the end user—either accidentally or deliberately. Swaging-induced cold-work in thermocouples, if uniformly applied, may result in a high level of homogeneity. However, on exposure to elevated temperatures, the subsequent recovery process from the cold-working can then result in significant drift, and this can in turn lead to erroneous temperature measurements, often in excess of the specified manufacturer tolerances. Several studies have investigated the effects of cold-work in Type K thermocouples usually by bending, or swaging. However, the amount of cold-work applied to the thermocouple is often difficult to quantify, as the mechanisms for applying the strains are typically nonlinear when applied in this fashion. A repeatable level of cold-working is applied to the different wires using a tensional loading apparatus to apply a known yield displacement to the thermoelements. The effects of thermal recovery from cold-working can then be accurately quantified as a function of temperature, using a linear gradient furnace and a high-resolution homogeneity scanner. Variation in these effects due to differing alloy compositions in Type K wire is also explored, which is obtained by sourcing wire from a selection of manufacturers. The information gathered in this way will inform users of Type K thermocouples about the potential consequences of varying levels of cold-working and its impact on the Seebeck coefficient at a range of temperatures between ˜ 70°C and 600° C. This study will also guide users on the temperatures required to rapidly alleviate the effects of cold-working using thermal annealing treatments.

Analysis of Potential for Titanium Liner Buckling after Proof in a Large Kevlar/Epoxy COPV

Science.gov (United States)

Phoenix, S. Leigh; Kezirian, Michael T.

2009-01-01

We analyze the potential for liner buckling in a 40-in Kevlar49/epoxy overwrapped spherical pressure vessel (COPV) due to long, local depressions or valleys in the titanium liner, which appeared after proof testing (autofrettage). We begin by presenting the geometric characteristics of approximately 20 mil (0.02 in.) deep depressions measured by laser profilometry in several vessels. While such depths were more typical, depths of more than 40 mils (0.02 in.) were seen near the equator in one particular vessel. Such depressions are largely the result of overlap of the edges of overwrap bands (with rectangular cross-section prepreg tows) from the first or second wrap patterns particularly where they start and end. We then discuss the physical mechanisms of formation of the depressions during the autofrettage process in terms of uneven void compaction in the overwrap around the tow overlap lines and the resulting 10-fold increase in through-thickness stiffness of the overwrap. We consider the effects of liner plastic yielding mechanisms in the liner on residual bending moments and interface pressures with the overwrap both at the peak proof pressure (approx.6500 psi) and when reducing the pressure to 0 psi. During depressurization the Bauschinger phenomenon becomes very important whereby extensive yielding in tension reduces the magnitude of the yield threshold in compression by 30 to 40%, compared to the virgin annealed state of the liner titanium. In the absence of a depression, the liner is elastically stable in compression even at liner overwrap interface pressures nominally 6 times the approx. 1000 psi interface pressure that exists at 0 psi. Using a model based on a plate-on-an-elastic-foundation, we develop an extensive analysis of the possible destabilizing effects of a frozen-in valley. The analysis treats the modifying effects of the residual bending moments and interface pressures remaining after the proof hold as well as the Bauschinger effect on the

Increasing marketability and profitability of product line thru PATRAN and NASTRAN

Science.gov (United States)

Hyatt, Art

1989-01-01

Starting with the design objective the operational cycle life of the Swaging Tool was increased. To accomplish this increase in cycle life without increasing the size or weight of the tool would be engineering achievement. However, not only was the operational cycle life increased between 2 to 10 times but simultaneously the size and weight of the Swage Tool was decreased by about 50 percent. This accomplishment now becomes an outstanding engineering achievement. This achievement was only possible because of the computerized Patran, Nastran and Medusa programs.

Oxide dispersion strengthened ferritic alloys. 14/20% chromium: effects of processing on deformation texture, recrystallization and tensile properties; Alliages ferritiques 14/20% de chrome renforces par dispersion d`oxydes. Effets des procedes de mise en forme sur les textures de deformation, la recristallisation et les proprietes de traction

Energy Technology Data Exchange (ETDEWEB)

Regle, H

1994-12-31

The ferritic oxide dispersion strengthened alloys are promising candidates for high temperature application materials, in particular for long life core components of advanced nuclear reactors. The aim of this work is to control the microstructure, in order to optimise the mechanical properties. The two ferritic alloys examined here, MA956 and MA957, are obtained by Mechanical Alloying techniques. They are characterised by quite anisotropic microstructure and mechanical properties. We have investigated the influence of hot and cold working processes (hot extrusion, swaging and cold-drawing) and recrystallization heat treatments on deformation textures, microstructures and tensile properties. The aim was to control the size of the grains and their anisotropic shape, using recrystallization heat treatments. After consolidation and hot extrusion, as-received materials present a extremely fine microstructure with elongated grains and a very strong (110) deformation texture with single-crystal character. At that stage of processing, recrystallization temperature are very high (1450 degrees C for MA957 alloy and 1350 degrees C for MA956 alloy) and materials develop millimetric recrystallized grains. Additional hot extrusion induce a fibre texture. Cold-drawing maintains a fibre texture, but the intensity decreases with increasing cold-work level. For both materials, the decrease of texture intensities correspond to a decrease of the recrystallization temperatures (from 1350 degrees C for a low cold-work level to 750 degrees C for 60 % cold-deformation, case of MA956 alloy) and a refinement of the grain size (from a millimetric size to less than an hundred of micrometer). Swaging develop a cyclic component where the intensity increases with increasing deformation in this case, the recrystallization temperature remains always very high and the millimetric grain size is slightly modified, even though cold-work level increases. (Abstract Truncated)

In vitro use characterization of the microorganism from land farming of the Presidente Getulio Vargas Refinery, Brazil, for soils decontamination; Caracterizacao in vitro do uso de microorganismos do landfarming da Refinaria Presidente Getulio Vargas - PETROBRAS-REPAR para a descontaminacao de solos

Energy Technology Data Exchange (ETDEWEB)

Krenczynski, Michele Cristine; Goncalves, Claudia Martins; Castro, Rodrigo Azevedo; Nascimento Neto, Durval [Parana Univ., Curitiba (Brazil). Pos-graduacao em Ciencia do Solo; Carvalho, Francisco Jose Pereira de Campos [Parana Univ., Curitiba (Brazil); Grube, Karl; Coelho, Ibirajara Jorge Evangelista [PETROBRAS, Rio de Janeiro, RJ (Brazil)

1998-07-01

In the present work, a set of experiments are reported from the evaluation of commercial use of the microorganisms of the Refinaria Presidente Getulio Vargas PETROBRAS land farming as inoculants for accelerating the bioremediation of contaminated soil with petroleum sludge, light naphtha, shale naphtha, toluene, heavy refinery oily waste, solp oil, sludge from the oily swage treatment plant, oily swage sludge and mixed oily wastes. These results are presented and discussed comparatively, and the characterization of the biodegradation activity of the land farming microorganisms for use in acceleration of bioremediation is discussed. (author)

The effect of annealing temperature on the properties of powder metallurgy processed Ti-35Nb-2Zr-0.5O alloy.

Science.gov (United States)

Málek, Jaroslav; Hnilica, František; Veselý, Jaroslav; Smola, Bohumil; Medlín, Rostislav

2017-11-01

Ti-35Nb-2Zr-0.5O (wt%) alloy was prepared via a powder metallurgy process (cold isostatic pressing of blended elemental powders and subsequent sintering) with the primary aim of using it as a material for bio-applications. Sintered specimens were swaged and subsequently the influence of annealing temperature on the mechanical and structural properties was studied. Specimens were annealed at 800, 850, 900, 950, and 1000°C for 0.5h and water quenched. Significant changes in microstructure (i.e. precipitate dissolution or grain coarsening) were observed in relation to increasing annealing temperature. In correlation with those changes, the mechanical properties were also studied. The ultimate tensile strength increased from 925MPa (specimen annealed at 800°C) to 990MPa (900°C). Also the elongation increased from ~ 13% (800°C) to more than 20% (900, 950, and 1000°C). Copyright © 2017 Elsevier Ltd. All rights reserved.

Full size U-10Mo monolithic fuel foil and fuel plate fabrication-technology development

International Nuclear Information System (INIS)

Moore, G.A.; Jue, J-F.; Rabin, B.H.; Nilles, M.J.

2010-01-01

Full-size U-10Mo foils are being developed for use in high density LEU monolithic fuel plates. The application of a zirconium barrier layer to the foil is performed using a hot co-rolling process. Aluminium clad fuel plates are fabricated using Hot Isostatic Pressing (HIP) or a Friction Bonding (FB) process. An overview is provided of ongoing technology development activities, including: the co-rolling process, foil shearing/slitting and polishing, cladding bonding processes, plate forming, plate-assembly swaging, and fuel plate characterization. Characterization techniques being employed include, Ultrasonic Testing (UT), radiography, and microscopy. (author)

Application of x-ray residual stress measurement to products

International Nuclear Information System (INIS)

Goto, T.; Iwamura, T.

1975-01-01

The X-ray residual stress measuring method is the only nondestructive method for measuring residual stress in polycrystalline materials. It is capable of obtaining information not only on macroscopic stress but also microscopic stress. The authors are employing this method for the development of pre-service and in-service inspection methods and for the improvement of various manufacturing techniques. In this paper, the results of measurement of some products as examples of its application are described. The examples introduced concern the following: (1) Selection of optimum conditions in heat treatment and stress-relief treatment. (2) Residual stress produced by mechanical processes such as autofrettage and flow form. (3) Check of manufacturing processes of rotary shaft and welded parts. (4) Estimation of fatigue strength of shot-peened part. (5) Detection of fatigue damage of shot-peened part. (auth.)

Utilization of carbon/carbon composites in nuclear simulation fuel rods

International Nuclear Information System (INIS)

Polidoro, H.A.; Otani, S.; Rezende, M.C.; Ferreira, S.R.; Otani, C.

1988-01-01

Thermo-hydraulic problems, in nuclear plants are normally analysed by using electrically heated rods. Carbon/carbon composites were used to make heating elements for testing by indirect heating up to a heat flux of 100 W/cm 2 . It is easy to verify that this value can be exceed if the choice of the complementary materials for insulator and cladding were improved. The swaging process used to reduce the cladding diameter prevented the fabrication of graphite heater rods. (author) [pt

Surgical implantation techniques for electronic tags in fish

Energy Technology Data Exchange (ETDEWEB)

Wagner, Glenn N.; Cooke, Steven J.; Brown, Richard S.; Deters, Katherine A.

2011-01-01

Intracoelomic implantation of transmitters into fish requires making a surgical incision, incision closure, and other surgery related techniques; however, the tools and techniques used in the surgical process vary widely. We review the available literature and focus on tools and techniques used for conducting surgery on juvenile salmonids because of the large amount of research that is conducted on them. The use of sterilized surgical instruments properly selected for a given size of fish will minimize tissue damage and infection rates, and speed the wound healing of fish implanted with transmitters. For the implantation of transmitters into small fish, the optimal surgical methods include making an incision on the ventral midline along the linea alba (for studies under 1 month), protecting the viscera (by lifting the skin with forceps while creating the incision), and using absorbable monofilament suture with a small-swaged-on swaged-on tapered or reverse-cutting needle. Standardizing the implantation techniques to be used in a study involving particular species and age classes of fish will improve survival and transmitter retention while allowing for comparisons to be made among studies and across multiple years. This review should be useful for researchers working on juvenile salmonids and other sizes and species of fish.

Process improvements for enhanced productivity of PHWR garter springs

International Nuclear Information System (INIS)

Srinivasula Reddy, S.; Tonpe, Sunil; Saibaba, N.; Jayaraj, R.N.

2009-01-01

Full text: In Pressurised Heavy Water Reactors (PHWR), Garter springs are used as spacers between the coolant tube and calandria tube. Garter springs are made from Zirconium alloy containing 2.5 % Niobium and 0.5% copper. The springs are basically manufactured by coiling a wire of cross section 1.7 mm x 1.0 mm, which is produced by series of drawing and swaging operations using hot extruded rods of 19 mm diameter. The manufacturing process also involves heat treatment and chemical cleaning operations at appropriate stages. It is required to ensure that the life of springs against parameters like hydrogen pickup, residual stresses and low stiffness is improved at the manufacturing stage itself by improving manufacturing process. The impact of above problems on spring life and process improvements is briefly discussed. The critical factor affecting the garter spring performance in PHWR Reactor is mainly hydrogen. The life limiting factors for garter springs are the problems arising out of high total hydrogen content, which depends on the hydrogen pickup during reactor operation. This phenomenon can happen during the reactor operation, as springs are prone to pick-up hydrogen in the reactor environment. Hence acceptable hydrogen content for the springs is specified as 25 ppm (max.). Garter spring is susceptible to hydrogen pick-up during various production processes, which make material brittle and difficult for fabrication process such as wire drawing and coiling. By studying and optimizing the process parameters of spring manufacturing, the hydrogen pick-up of springs is brought down from 70 ppm to a level of 20 ppm. Garter springs are provided with a hook at each end to enable its assembly to coolant tube in the reactor. The hook portion is very critical in maintaining the integrity of the spring. It is desirable to have the hook portion relieved of all residual stresses. For this purpose manufacturing process has been modified and solutionising was introduced as

Strength-toughness requirements for thick walled high pressure vessels

International Nuclear Information System (INIS)

Kapp, J.A.

1990-01-01

The strength and toughness requirements of materials for use in high pressure vessels has been the subject of some discussion in the meetings of the Materials Task Group of the Special Working Group High Pressure Vessels. A fracture mechanics analysis has been performed to theoretically establish the required toughness for a high pressure vessel. This paper reports that the analysis performed is based on the validity requirement for plane strain fracture of fracture toughness test specimens. This is that at the fracture event, the crack length, uncracked ligament, and vessel length must each be greater than fifty times the crack tip plastic zone size for brittle fracture to occur. For high pressure piping applications, the limiting physical dimension is the uncracked ligament, as it can be assumed that the other dimensions are always greater than fifty times the crack tip plastic zone. To perform the fracture mechanics analysis several parameters must be known: these include vessel dimensions, material strength, degree of autofrettage, and design pressure. Results of the analysis show, remarkably, that the effects of radius ratio, pressure and degree of autofrettage can be ignored when establishing strength and toughness requirements for code purposes. The only parameters that enter into the calculation are yield strength, toughness and vessel thickness. The final results can easily be represented as a graph of yield strength against toughness on which several curves, one for each vessel thickness, are plotted

An integrated CAD/CAM system for CNG pressure vessel manufactured by deep drawing and ironing operation

Energy Technology Data Exchange (ETDEWEB)

Park, Joon Hong; Kim, Chul; Choi, Jae Chan [Pusan National Univ., Pusan (Korea, Republic of)

2004-06-01

The fiber reinforced composite material is widely used in the multi-industrial field because of their high specific modulus and specific strength. It has two main merits which are to cut down energy by reducing weight and to prevent explosive damage proceeding to the sudden bursting which is generated by the pressure leakage condition. Therefore, pressure vessels using this composite material can be applied in the field such as defence industry and aerospace industry. In this paper, for nonlinear finite element analysis of E-glass/epoxy filament winding of composite vessel subjected to internal pressure, the standard interpretation model is developed by using the ANSYS with AutoLISP and ANSYS APDL languages, general commercial software, which is verified as useful characteristic of the solution. Among the modules of the system, both the process planning module for carrying out the process planning of filament wound composite pressure vessel and the autofrettage process module for obtaining higher residual stress will minimize trial and error and reduce the period for developing new products. The system can serve as a valuable system for experts and as a dependable training aid for beginners.

An integrated CAD/CAM system for CNG pressure vessel manufactured by deep drawing and ironing operation

International Nuclear Information System (INIS)

Park, Joon Hong; Kim, Chul; Choi, Jae Chan

2004-01-01

The fiber reinforced composite material is widely used in the multi-industrial field because of their high specific modulus and specific strength. It has two main merits which are to cut down energy by reducing weight and to prevent explosive damage proceeding to the sudden bursting which is generated by the pressure leakage condition. Therefore, pressure vessels using this composite material can be applied in the field such as defence industry and aerospace industry. In this paper, for nonlinear finite element analysis of E-glass/epoxy filament winding of composite vessel subjected to internal pressure, the standard interpretation model is developed by using the ANSYS with AutoLISP and ANSYS APDL languages, general commercial software, which is verified as useful characteristic of the solution. Among the modules of the system, both the process planning module for carrying out the process planning of filament wound composite pressure vessel and the autofrettage process module for obtaining higher residual stress will minimize trial and error and reduce the period for developing new products. The system can serve as a valuable system for experts and as a dependable training aid for beginners

FABRICATION OF TUBE TYPE FUEL ELEMENT FOR NUCLEAR REACTORS

Science.gov (United States)

Loeb, E.; Nicklas, J.H.

1959-02-01

A method of fabricating a nuclear reactor fuel element is given. It consists essentially of fixing two tubes in concentric relationship with respect to one another to provide an annulus therebetween, filling the annulus with a fissionablematerial-containing powder, compacting the powder material within the annulus and closing the ends thereof. The powder material is further compacted by swaging the inner surface of the inner tube to increase its diameter while maintaining the original size of the outer tube. This process results in reduced fabrication costs of powdered fissionable material type fuel elements and a substantial reduction in the peak core temperatures while materially enhancing the heat removal characteristics.

Microstructure and hardness development in a copper-nickel diffusion gradient model system

DEFF Research Database (Denmark)

Duchstein, Linus Daniel Leonhard; Zhang, Xiaodan; Hansen, Niels

2015-01-01

Cu has been electrolytically coated with Ni and subsequently deformed by rotary swaging up to a strain of ε=2 to create a chemical gradient at the interface of the two elements. The extend of this chemical intermixing has been investigated through Energy Dispersive X-ray (EDX) spectroscopy...

77 FR 42958 - Airworthiness Directives; Eurocopter Deutschland GmbH Helicopters

Science.gov (United States)

2012-07-23

... airworthiness directive (AD) for Eurocopter Deutschland GmbH (ECD) Model MBB-BK 117 (all versions) and BO-105LS... tail rotor pitch link and subsequent loss of control of the helicopter. DATES: This AD becomes... improperly swaged spherical bearing on the pitch link, which could result in loss of tail rotor control and...

Application Of Lean Strategy To Redesign The Assembly Process Flow Of Glow Plug

Directory of Open Access Journals (Sweden)

Rahul Vylen

2013-06-01

Full Text Available Lean manufacturing is an applied methodology of scientific objective techniques which will improve the tasks in a process to be performed with a minimum of non-value-added activities. It is being increasingly adopted as a potential solution for many automotive manufacturing industries. This paper addresses the implementation of lean principles in an automotive component manufacturing company with a focus on current manufacturing practices and visual identification of non-value-added time, such as bottle necking, waiting time and material handling, etc. The typical operations involved in making the Glow Plug are caulking, tig welding, MgO filling & O-ring pressing, swaging, facing, thread rolling, inspection and assembly. The facing operation can be eliminated by stabilizing the variations generated during the MgO filling machine. The MgO filling activity contains various forms of non-value-added activities such as worn-out gripper, insufficient clamping tension, physical shaking of the WPC on the agitation unit instead of fine vibration, Jerky insertion of the WPC shank into the agitation locator. It was identified that approximately 15mm material was wasted per piece, though there is no value addition on the part. This project utilizes Lean tools such as “Six Sigma” and “Value Stream Mapping” procedures. Resolving and improving the above problems resulted in drastic increase in productivity by 87% from 82%, reduction in the rejections by 13% from 18%, reduction in the manufacturing lead time by 2.62 days/annum, reduction in the utilization of shop floor space by 6m2 and also the manufacturing cost by 1.16 million INR/ annum.

CONTROL ROD

Science.gov (United States)

Walker, D.E.; Matras, S.

1963-04-30

This patent shows a method of making a fuel or control rod for a nuclear reactor. Fuel or control material is placed within a tube and plugs of porous metal wool are inserted at both ends. The metal wool is then compacted and the tube compressed around it as by swaging, thereby making the plugs liquid- impervious but gas-pervious. (AEC)

Diverless pipeline repair system for deep water

Energy Technology Data Exchange (ETDEWEB)

Spinelli, Carlo M. [Eni Gas and Power, Milan (Italy); Fabbri, Sergio; Bachetta, Giuseppe [Saipem/SES, Venice (Italy)

2009-07-01

SiRCoS (Sistema Riparazione Condotte Sottomarine) is a diverless pipeline repair system composed of a suite of tools to perform a reliable subsea pipeline repair intervention in deep and ultra deep water which has been on the ground of the long lasting experience of Eni and Saipem in designing, laying and operating deep water pipelines. The key element of SiRCoS is a Connection System comprising two end connectors and a repair spool piece to replace a damaged pipeline section. A Repair Clamp with elastomeric seals is also available for pipe local damages. The Connection System is based on pipe cold forging process, consisting in swaging the pipe inside connectors with suitable profile, by using high pressure seawater. Three swaging operations have to be performed to replace the damaged pipe length. This technology has been developed through extensive theoretical work and laboratory testing, ending in a Type Approval by DNV over pipe sizes ranging from 20 inches to 48 inches OD. A complete SiRCoS system has been realised for the Green Stream pipeline, thoroughly tested in workshop as well as in shallow water and is now ready, in the event of an emergency situation.The key functional requirements for the system are: diverless repair intervention and fully piggability after repair. Eni owns this technology and is now available to other operators under Repair Club arrangement providing stand-by repair services carried out by Saipem Energy Services. The paper gives a description of the main features of the Repair System as well as an insight into the technological developments on pipe cold forging reliability and long term duration evaluation. (author)

Strain aging in tungsten heavy alloys

International Nuclear Information System (INIS)

Dowding, R.J.; Tauer, K.J.

1991-01-01

This paper reports on tungsten heavy alloys which are two-phase mixtures of body center cubic (BCC) tungsten surrounded by a face center cubic (FCC) matrix. The matrix is most often composed of nickel and iron in a ratio of 70:30 but, occasionally, the matrix may also contain cobalt or copper. Nickel, however, is always the primary matrix component. The tungsten heavy alloy is fabricated through powder metallurgy techniques. Elemental powders are blended, pressed to shape, and sintered. Depending upon the tungsten content, the sintering temperatures are usually in the range of 1450 degrees C to 1525 degrees C. These temperatures are high enough that, as a result, the matrix is at the liquid phase and the process is known as liquid phase sintering. At the liquid phase temperature, the matrix becomes saturated with tungsten, but this does not change the FCC character of the matrix. The sintering is usually done in a hydrogen atmosphere furnace in order to reduce the oxides on the tungsten powder surfaces and create clean, active surfaces which will enhance the adherence between the tungsten and the matrix. The hydrogen atmosphere also creates the presence of excess dissolved hydrogen in the alloy. It has been shown that the hydrogen degrades the toughness and ductility of the heavy alloy. A post-sintering vacuum heat treatment is generally required to insure that there is no residual hydrogen present. The as-sintered tensile strength of a 90% tungsten, 7% nickel, 3% iron alloy (90W) is in the range of 800 to 940 MPa and can be increased significantly by cold working, usually rolling or swaging. Swaging to reductions in area of 20% can result in tensile strengths of 1250 MPa or more. As the strength increases, the elongation, which may have been 30% or more, decreases to less than 5%

Correlations between the post-HIP treatment, resulting microstructure and fatigue behaviour of prealloyed Ti6Al4V powder compacts

International Nuclear Information System (INIS)

Wirth, G.; Grundhoff, K.J.; Smarsly, W.

1985-01-01

Prealloyed Ti6Al4V powders, hot isostatically pressed in the (alpha + beta) temperature range, always possess a mixed microstructure of lenticular and equiaxed parts. Numerous treatments have been used to improve microstructural homogeneity, especially to achieve fine equiaxed grains well known to possess good HCF properties. In this contribution, four different conditions of HIP compacts from ultraclean PREP powder were investigated together with PSV powder compacted by combined die forging (CDF). The HIP compacts had pure equiaxed and lenticular, a mixture of both (as HIP) as well as a swaged + beta annealed microstructure. The best HCF fatigue strength was correlated to the last condition instead of the expected equiaxed microstructure. CDF resulted in a homogeneous equiaxed microstructure which thus could be achieved by a one-step compaction process directly from untreated powder. 12 references

The effect of various deformation processes on the corrosion behavior of casing and tubing carbon steels in sweet environment

Science.gov (United States)

Elramady, Alyaa Gamal

The aim of this research project is to correlate the plastic deformation and mechanical instability of casing steel materials with corrosion behavior and surface change, in order to identify a tolerable degree of deformation for casing steel materials. While the corrosion of pipeline and casing steels has been investigated extensively, corrosion of these steels in sweet environments with respect to plastic deformation due to bending, rolling, autofrettage, or handling needs more investigation. Downhole tubular expansion of pipes (casings) is becoming standard practice in the petroleum industry to repair damaged casings, shutdown perforations, and ultimately achieve mono-diameter wells. Tubular expansion is a cold-drawing metal forming process, which consists of running conical mandrels through casings either mechanically using a piston or hydraulically by applying a back pressure. This mechanism subjects the pipes to large radial plastic deformations of up to 30 pct. of the inner diameter. It is known that cold-working is a way of strengthening materials such as low carbon steel, but given that this material will be subjected to corrosive environments, susceptibility to stress corrosion cracking (SCC) should be investigated. This research studies the effect of cold-work, in the form of cold-rolling and cold-expansion, on the surface behavior of API 5CT steels when it is exposed to a CO2-containing environment. Cold-work has a pronounced influence on the corrosion behavior of both API 5CT K55 and P110 grade steels. The lowest strength grade steel, API 5CT K55, performed poorly in a corrosive environment in the slow strain rate test. The ductile material exhibited the highest loss in strength and highest susceptibility to stress corrosion cracking in a CO 2-containing environment. The loss in strength declined with cold-rolling, which can be ascribed to the surface compressive stresses induced by cold-work. On the other hand, API 5CT P110 grade steels showed higher

Stress concentration effects in high pressure components

International Nuclear Information System (INIS)

Aller, J.E.

1990-01-01

This paper examines the stress concentration effects of sideholes in thick walled, high pressure cylinders. It has been shown that the theoretical stress concentration factor at the intersection of a small crossbore in a closed end, thick walled cylinder varies between 3.0 and 4.0. Tests have shown that this effect can be greatly reduced in practice by carefully radiusing the bore intersection and autofrettaging the cylinder. It has also been shown that the minimum stress concentration factor occurs when the main bore and sidehole or crossbore have the same diameter, and the radius of the intersection is approximately equal to the sidehole radius. When the bore and sidehole intersection angle decreases from 90 degrees, the stress concentration factor increases significantly. Knowledge of these fundamental relationships can be used in maintaining, as well ad designing, high pressure equipment

Oxygen sensor development and low temperature corrosion study in lead-alloy coolant loop

International Nuclear Information System (INIS)

Hwang, Il Soon; Bahn, Chi Bum; Lee, Seung Gi; Jeong, Seung Ho; Nam, Hyo On; Lim, Jun

2007-07-01

Oxygen sensor to measure dissolved oxygen concentration at liquid lead-bismuth eutectic environments have been developed. Developed oxygen sensor for application in lead-bismuth eutectic (LBE) system was based on the oxygen ion conductor made of YSZ ceramic having Bi/Bi2O3 reference joined by electro-magnetic swaging. Leakage problem, which was major problem of existing sensors, can be solved by using electro-magnetic swaging method. A new calibration strategy combining the oxygen titration with electrochemical impedance spectroscopy (EIS) was performed to increase the reliability of sensor. Another calibration was also conducted by controlling the oxygen concentration using OCS (oxygen control system). Materials corrosion tests of various metals (SS316, EP823, T91 and HT9) were conducted for up to 1,000 hours with specimen inspection after every 333hours at 450 .deg. C in HELIOS. Oxygen concentration was controlled at 10 -6 wt% by using the direct gas bubbling of Ar+4%H 2 , Ar+5%O 2 and pure Ar. The dissolved oxygen concentration in LBE was also monitored by two calibrated YSZ oxygen sensors located at different places under different temperatures within HELIOS. It shows a good performance during 1000 hours. Liquid metal embrittlement (LME) test of SS316L specimen in the LBE was performed at various temperature and strain rate. The result shows that the liquid metal embrittlement effect is not crucial at tested conditions

Heater Validation for the NEXT-C Hollow Cathodes

Science.gov (United States)

Verhey, Timothy R.; Soulas, George C.; Mackey, Jonathan A.

2018-01-01

Swaged cathode heaters whose design was successfully demonstrated under a prior flight project are to be provided by the NASA Glenn Research Center for the NEXT-C ion thruster being fabricated by Aerojet Rocketdyne. Extensive requalification activities were performed to validate process controls that had to be re-established or revised because systemic changes prevented reuse of the past approaches. A development batch of heaters was successfully fabricated based on the new process controls. Acceptance and cyclic life testing of multiple discharge and neutralizer sized heaters extracted from the development batch was initiated in August, 2016, with the last heater completing testing in April, 2017. Cyclic life testing results substantially exceeded the NEXT-C thruster requirement as well as all past experience for GRC-fabricated units. The heaters demonstrated ultimate cyclic life capability of 19050 to 33500 cycles. A qualification batch of heaters is now being fabricated using the finalized process controls. A set of six heaters will be acceptance and cyclic tested to verify conformance to the behavior observed with the development heaters. The heaters for flight use will be then be provided to the contractor from the remainder of the qualification batch. This paper summarizes the fabrication process control activities and the acceptance and life testing of the development heater units.

Development of electrically heated rods with resistive element of graphite or carbon/carbon composites for simulating transients in nuclear reactors

International Nuclear Information System (INIS)

Polidoro, H.A.

1987-01-01

Thermo-hydraulic problems, in nuclear plants are normally analysed by the use of electrically heated rods. The direct or indirect heater rods are limited in their use because, for high temperatures and high heat flux, the heating element temperature approach its melting point. The use of platinum or tantalum is not economically viable. Graphite and carbon/carbon composites are alternative materials because they are good electrical conductors and have good mechanical properties at high temperatures. Graphite and carbon/carbon composites were used to make heating elements for testing by indirect heating. The swaging process used to reduce the cladding diameter prevented the fabrication of graphite heater rods. Carbon/carbon composite used to make heating elements gave good results up to a heat flux of 100 W/cm 2 . It is easy to verify that this value can be exceeded if the choice of the complementary materials for insulator and cladding improved. (author) [pt

Elaboration and characterization of silver sheathed YBaCuO and BiSrCaCuO wires

International Nuclear Information System (INIS)

Regnier, P.; Chaffron, L.; Schmirgeld, L.

1990-01-01

We report on our recent progress in the elaboration of silver sheathed high-Tc superconducting wires. It is shown that careful optimization of the swaging and pressing stages leads to a compacity of nearly 100% for the green ceramic, which considerably reduces the problem of its shrinkage in the silver clad during sintering, and consequently increases the critical current density far above 10 3 A/cm 2 at 77 K. Electrical and microstructural characterization of the wires are presented and compared with other published data. In particular, for both YBaCuO and BiSrCaCuO ribbons, it is shown that the thinner the ribbon the higher the critical current density. But this effect is much more pronounced for BiSrCaCuO because, due to partial melting of the former ceramic during the elaboration process, there is a pronounced enhancement of its texture as its thickness is reduced

A study on the development of high-Tc superconducting wire

International Nuclear Information System (INIS)

Won, Dong Yeon; Lee, Hee Gyoun; Kim, Chan Joong

1991-09-01

High magnetization YBaCuO superconductor was prepared with additions of BaSnO 3 , SnO 2 and SiC by partial melt processing. Addition of BaSnO 3 increased the magnetic property of YBaCuO by flux pinning action of finely dispersed BaSnO 3 particles, while addition of SnO 2 decreased the magnetic property, because the size of particle was larger than that of BaSnO 3 . BiPbSrCaCuO superconducting tape of single filament was prepared by powder-in-tube method using silver as a shearth material. The fabrication techniques involves powder packing, swaging, drawing and cold rolling/pressing method. The final dimension of wire after drawing is 1.2mm diameter. The wire was pressed into a tape form with a thickness of 70micron and a width of 3mm. The obtained critical current density of the prepared tape was 2000A/cm 2 at 77K. (Author)

Cu-Nb3Sn superconducting wires prepared by ''Copper Liquid Phase Sintering method'' using the Nb-H

International Nuclear Information System (INIS)

Resende, A.T. de.

1985-01-01

Cu-30% Nb in weighting were prepared by the method of Copper sintering liquid phase the method was improved by substitution of Nb power by Nb-H powder, obtaining a high density material with good mechanical properties, which was reduced to fine. Wire, Without heat treatment. The Cu-Nb 3 Sn wires were obtained by external diffusion process depositing tin in the Cu-30%Nb wires, and by internal diffusion process using the Sn-8.5% Cu in weighting, which was reduced to rods of 3.5 mm. These Cu-30%Nb rods were enclosed in copper tubes and deformed mechanically by rotary swaging and drawing. During the drawing step some wires were fractured, that were analysed and correlated with the microstructure of the Sn-8.5 Wt% Cu alloy. External and internal diffusion samples; after a fast thermal treatment for Sn diffusion, were submited to the temperature of 700 0 C to provide the reaction between Sn and Nb, leading to the Nb 3 Sn phase. Samples with several reaction times, and its influence on T c and J c critical parameters and normal resistivity were prepared and analysed. (author) [pt

The Conceptual Design for Tubular Fuel Assemblies of an Advanced Research Reactor

International Nuclear Information System (INIS)

Ryu, Jeong Soo; Dan, Ho Jin; Cho, Yeong Garp; Yoon, Doo Byung; Park, Cheol

2005-05-01

An Advanced Research Reactor(ARR) is being designed by KAERI since 2002. The final goal of the project is to develop a new and unique research reactor model which is superior in safety and economical aspects. In this work, the conceptual design for tubular fuel assemblies was carried out to enhance the previous model. The shape optimization of the cross section of the top guide was performed, and the swaging procedure in connecting fuel plates and stiffeners was developed. Moreover to reflect changes in number and size of fuel plates, related parts of the standard and the reduced fuel assemblies were redesigned. The top guide should suppress the vibration of the fuel assembly due to coolant and resist against material failures owing to fatigue and yield. In order to gain these design requirements, we have optimized the section profile of the top guide. To confirm manufacturing aspects, the swaging procedure was developed and its performance was tested. The results of tangential tensile test and axial compression test guaranteed that the fixing state between fuel plates and stiffeners is firm enough to hold each other. In addition, due to changes in number and size of fuel plates, the outer cross section of the fuel assembly was expanded and the diameter of the spacer tube was reduced. Reflecting these design changes, top/bottom guide, top guide cover, spring, spring cover, and receptacle were readjusted. Based on the technical experiences on the design and operation of the HANARO, the standard and the reduced fuel assemblies will be verified by performing various tests and analysis

Method of making V.sub.3 Ga superconductors

Science.gov (United States)

Dew-Hughes, David

1980-01-01

An improved method for producing a vanadium-gallium superconductor wire having aluminum as a component thereof is disclosed, said wire being encased in a gallium bearing copper sheath. The superconductors disclosed herein may be fabricated under normal atmospheres and room temperatures by forming a tubular shaped billet having a core composed of an alloy of vanadium and aluminum and an outer sheath composed of an alloy of copper, gallium and aluminum. Thereafter the entire billet is swage reduced to form a wire therefrom and heat treated to form a layer of V.sub.3 Ga in the interior of the wire.

Nuclear fuels for material test reactors

International Nuclear Information System (INIS)

Ramanathan, L.V.; Durazzo, M.; Freitas, C.T. de

1982-01-01

Experimental results related do the development of nuclear fuels for reactors cooled and moderated by water have been presented cylindrical and plate type fuels have been described in which the core consists of U compouns dispersed in an Al matrix and is clad with aluminium. Fabrication details involving rollmilling, swaging or hot pressing have been described. Corrosion and irradiation test results are also discussed. The performance of the different types of fuels indicates that it is possible to locally fabricate fuel plates with U 3 O 8 +Al cores (20% enriched U) for use in operating Brazilian research reactors. (Author) [pt

Effect of Sn addition on phases stability and mechanical properties of aged Ti-10Mo Alloy

International Nuclear Information System (INIS)

Cardoso, F.F.; Lopes, E.S.N.; Cremasco, A.; Contieri, R.J.; Mello, M.G.; Caram, R.

2010-01-01

Nowadays there is considerable effort in order to develop new titanium alloys using non-toxic elements such as Mo and Sn. This work deals with the alloys Ti-Mo-Sn. The samples were melted, homogenized and hot swaged. Afterwards they were solubilized and water quenched. The alloys were also aged at several temperatures Characterization involved determination of Young's modulus, hardness, X-ray diffraction and optical microscopy. The X-ray diffraction indicated the presence of athermal and isothermal ω phase for Ti-10Mo alloy. One also evidenced that the Vickers hardness varies with the temperature and the time of aging heat treatment. (author)

Innovative approaches in the manufacture of zirconium alloy components for PHWRs

International Nuclear Information System (INIS)

Rao, M.N.; Srivastava, R.K.

2005-01-01

Selection of an appropriate route for the fabrication of Zirconium alloy fuel components has a direct bearing on the quality of finished product. Many sophisticated and intricate processes such as vacuum arc melting, extrusion, hot rolling and cold working processes - swaging, drawing and sheet rolling are employed. Many advances were made in eddy current and ultrasonic evaluation to meet the stringent quality control requirement and locate the micro flaws. Emphasis was laid on achieving high recoveries and manufacture the product at minimum cost. Several creative and innovative processes were adopted particularly in the fabrication of end caps and spacers. The spacers were produced through the wire route and subsequently parting them into tiny spacers, which is entirely different from the conventional route of fabricating the sheets followed by blanking and coining. This has improved the material recovery and the lead time has been reduced substantially. The end caps used for the closure of clad tubes have to meet the most stringent quality requirements to avoid micro-flaws. The manufacturing processes adopted have direct influence on the integrity of the finished product. Special defect standards were developed to identify and eliminate micro-flaws and thereby ensure consistent and repetitive quality product. The paper brings out the above innovative approaches made in fabrication and quality control techniques in the manufacture of fuel components for PHWR fuel bundles. (author)

Experimental Qualification of the Sleeved Pin Multilink Attachment for Divertor PFC's

International Nuclear Information System (INIS)

Poutanen, J.; McCallum, A.; Turner, A.; Merola, M.

2006-01-01

The latest design for connecting the limited life ITER divertor plasma facing components (PFC's) to the reusable cassette body is the so called sleeved pin multilink attachment. The connection is made by expanding a 43 mm diameter hollow AlBr pin inside the fixation holes of components of the cassette body and PFC by a swaging process. The multilink is an easy, safe and fast assembly method, but the original dismantling method of drilling out the pin was found troublesome. Therefore, in the latest attachment design a thin sleeve is incorporated between the pin and the holes, which makes it possible to dismantle the joint by simply pulling out the pin and sleeve sequentially. Experimental qualification of the new sleeved design is now proceeding. The aim of the experimental qualification is to prove that the sleeved design meets the requirements of load carrying capability, clearance free connection, and easy and safe removal. Associated analytical studies were performed to develop and verify theoretical models and correlations for use in design. Results from the experimental qualification will provide reference information for developing tools for making and removing the connection. Theoretical finite element models in association with the results of earlier test campaigns with nonsleeved design were used to determine pin expansion parameters. The expansion parameters were verified with plate-pin tests measuring contact pressures produced by pin expansion. The plate-pin tests were also used to demonstrate the feasibility of pin removal and develop pin removal methodology. The mechanical capabilities of the connection design are being examined with test series of cyclic tensile loading plus articulation-induced loading of a single connection mock-up. Remaking properties of the attachment are being studied with multiple swaging and removing of the pin into the fixation holes. Finally the dismantling of the connection will be examined with full length pin extraction

Mechanical properties and microstructure of Ti-35.5Nb-5.7Ta beta alloy.

Science.gov (United States)

Bartakova, S; Prachar, P; Dvorak, I; Hruby, V; Vanek, J; Pospichal, M; Svoboda, E; Martikan, A; Konecna, H; Sedlak, I

2015-01-01

Titanium and titanium alloys represent generally accepted metallic biomaterials for clinical dentistry and dental implantology. In this paper, we present a Ti-35.5Nb-5.7Ta alloy with a special respect to its microstructure and mechanical characteristics, such as Young modulus of elasticity. Three thermal treatments differing in temperature and time of annealing were used during the Ti-35.5Nb-5.7Ta processing in order to evaluate the effects of ageing, melting annealing, and annealing on mechanical characteristics and microstructure. Using microscopy, the alloy was analyzed and the differences in shares of beta phase grains, alpha particles and precipitates evaluated. The three thermal treatments were evaluated also from technological point of view. The following thermal treatment was found optimal for the Ti-35.5Nb-5.7Ta alloy: melting annealing at 800 °C for 0.5 hour followed by a cold swaging with a 52-79 % deformation, and final hardening at 500 °C for 2 hours in water(Tab. 2, Fig. 3, Ref. 24).

High density tungsten-nickel-iron-cobalt alloys having improved hardness and method for making same

International Nuclear Information System (INIS)

Penrice, T.W.; Bost, J.

1988-01-01

This patent describes the process of making high density alloy containing about 85 to 98 weight percent tungsten and the balance of the alloy being essentially a binder of nickel, iron and cobalt, and wherein the cobalt is present in an amount within the range of about 5 to 47.5 weight percent of the binder, comprising: blending powders of the tungsten, nickel, iron and cobalt into a homogeneous composition, compacting the homogeneous composition into a shaped article, heating the shaped article to a temperature and for a time sufficient to sinter the article, subjecting the sintered article to a temperature sufficient to enable the intermetallic phase formed at the matrix to tungsten interface to diffuse into the gamma austenitic phase whereby the alpha tungsten/gamma austenite boundaries are essentially free of such intermetallic phase, quenching the article, and swaging the article to a reduction in area of about 5 to 40 percent, the article having improved mechanical properties, including improved tensile strength and hardness while maintaining suitable ductility for subsequent working thereof

Study of structure and residual stresses in cold rotary swaged tungsten heavy alloy

Czech Academy of Sciences Publication Activity Database

Kunčická, L.; Kocich, R.; Hervoches, Charles; Macháčková, A.

2017-01-01

Roč. 705, č. 9 (2017), s. 25-31 ISSN 0921-5093 R&D Projects: GA MŠk LM2015056 Institutional support: RVO:61389005 Keywords : Tungsten heavy alloy * residual stresses * neutron scattering * electron microscopy * work hardening Subject RIV: BM - Solid Matter Physics ; Magnetism OBOR OECD: Condensed matter physics (including formerly solid state physics, supercond.) Impact factor: 3.094, year: 2016

Effect of Sn addition on phases stability and mechanical properties of aged Ti-10Mo Alloy; Efeito da adicao de Sn na estabilidade de fases e propriedades de ligas Ti-10Mo resfriadas rapidamente e envelhecidas

Energy Technology Data Exchange (ETDEWEB)

Cardoso, F.F.; Lopes, E.S.N.; Cremasco, A.; Contieri, R.J.; Mello, M.G.; Caram, R., E-mail: flaviamec@fem.unicamp.b [Universidade Estadual de Campinas (FEM/UNICAMP), SP (Brazil). Fac. de Engenharia Mecanica

2010-07-01

Nowadays there is considerable effort in order to develop new titanium alloys using non-toxic elements such as Mo and Sn. This work deals with the alloys Ti-Mo-Sn. The samples were melted, homogenized and hot swaged. Afterwards they were solubilized and water quenched. The alloys were also aged at several temperatures Characterization involved determination of Young's modulus, hardness, X-ray diffraction and optical microscopy. The X-ray diffraction indicated the presence of athermal and isothermal {omega} phase for Ti-10Mo alloy. One also evidenced that the Vickers hardness varies with the temperature and the time of aging heat treatment. (author)

Mechanical behaviour of copper 15% volume niobium microcomposite wires

Directory of Open Access Journals (Sweden)

Marcello Filgueira

2001-01-01

Full Text Available Cu-Nb microcomposites are attractive in magnet pulsed field technology applications due to their anomalous mechanism of mechanical strength and high electrical conductivity. In this sense, recently it was conceived the use of Cu 15% vol. Nb wires to operate as a high tensile strength cable for a diamond cutting tool (diamond wires for marble and granite slabbing. The multifilamentary Cu 15% vol. Nb composite was obtained using a new processing route, starting with niobium bars bundled into copper tubes, without arc melting. Cold working techniques, such as swaging and wire drawing, combined with heat treatments such as sintering and annealing, and tube restacking were employed. The tensile property of the composite was measured as a function of the niobium filaments dimensions and morphology into the copper matrix, in the several processing steps. An ultimate tensile strength (UTS of 960 MPa was obtained for an areal reduction (R = Ao/A, with Ao-initial cross section area, and A-final cross section area of 4x10(8 X, in which the niobium filaments reached thickness less than 20 nm. The anomalous mechanical strength increase is attributed to the fact that the niobium filaments acts as a barrier to copper dislocations.

Fabrication of U-10wt.%Zr Fuel slug for SFR by Injection Casting

International Nuclear Information System (INIS)

Kim, Jong Hwan; Song, Hoon; Kim, Hyung Tae; Ko, Young Mo; Kim, Ki Hwan; Lee, Chan B.

2013-01-01

The fabrication technology of metal fuel has been developed by various methods such as rolling, swaging, wire drawing, and co-extrusion, but each of these methods had process limitations requiring an additional subsequent process, and needing the fabrication equipment is complex, which is not favorable for remote use. A practical process of metallic fuel fabrication for an SFR needs to be cost efficient, suitable for remote operation, and capable of mass production while reducing the amount of radioactive waste. Injection casting was chosen as the most promising technique, in the early 1950s, and this technique has been applied to fuel slug fabrication for the Experimental Breeder Reactor-II (EBR-II) driver and the Fast Flux Test Facility (FFTF) fuel pins. Because of the simplistic nature of the process and equipment, compared to other processes examined, this process has been successfully used in a remote operation environment for fueling of the EBR-II reactor. In this study, vacuum injection casting suitable for remote operation has been developed to fabricate metallic fuel for an SFR. Vacuum injection casting technique was developed to fabricate metallic fuel for an SFR. The appearance of the fabricated U-10wt.%Zr fuel was generally sound and the internal integrity was found to be satisfactory through gamma-ray radiography. Minimum fuel losses after casting relative to the initial charge amount of U-10wt.%Zr fuel slugs met the proposed goal of less than 0.1% fuel losses during fabrication. Modifications of the current facility system and advanced casting techniques are underway to produce higher quality fuel slugs

Fabrication of U-10wt.%Zr Fuel slug for SFR by Injection Casting

Energy Technology Data Exchange (ETDEWEB)

Kim, Jong Hwan; Song, Hoon; Kim, Hyung Tae; Ko, Young Mo; Kim, Ki Hwan; Lee, Chan B. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2013-10-15

The fabrication technology of metal fuel has been developed by various methods such as rolling, swaging, wire drawing, and co-extrusion, but each of these methods had process limitations requiring an additional subsequent process, and needing the fabrication equipment is complex, which is not favorable for remote use. A practical process of metallic fuel fabrication for an SFR needs to be cost efficient, suitable for remote operation, and capable of mass production while reducing the amount of radioactive waste. Injection casting was chosen as the most promising technique, in the early 1950s, and this technique has been applied to fuel slug fabrication for the Experimental Breeder Reactor-II (EBR-II) driver and the Fast Flux Test Facility (FFTF) fuel pins. Because of the simplistic nature of the process and equipment, compared to other processes examined, this process has been successfully used in a remote operation environment for fueling of the EBR-II reactor. In this study, vacuum injection casting suitable for remote operation has been developed to fabricate metallic fuel for an SFR. Vacuum injection casting technique was developed to fabricate metallic fuel for an SFR. The appearance of the fabricated U-10wt.%Zr fuel was generally sound and the internal integrity was found to be satisfactory through gamma-ray radiography. Minimum fuel losses after casting relative to the initial charge amount of U-10wt.%Zr fuel slugs met the proposed goal of less than 0.1% fuel losses during fabrication. Modifications of the current facility system and advanced casting techniques are underway to produce higher quality fuel slugs.

Closeout of JOYO-1 Specimen Fabrication Efforts

International Nuclear Information System (INIS)

ME Petrichek; JL Bump; RF Luther

2005-01-01

Fabrication was well under way for the JOYO biaxial creep and tensile specimens when the NR Space program was canceled. Tubes of FS-85, ASTAR-811C, and T-111 for biaxial creep specimens had been drawn at True Tube (Paso Robles, CA), while tubes of Mo-47.5 Re were being drawn at Rhenium Alloys (Cleveland, OH). The Mo-47.5 Re tubes are now approximately 95% complete. Their fabrication and the quantities produced will be documented at a later date. End cap material for FS-85, ASTAR-811C, and T-111 had been swaged at Pittsburgh Materials Technology, Inc. (PMTI) (Large, PA) and machined at Vangura (Clairton, PA). Cutting of tubes, pickling, annealing, and laser engraving were in process at PMTI. Several biaxial creep specimen sets of FS-85, ASTAR-811C, and T-111 had already been sent to Pacific Northwest National Laboratory (PNNL) for weld development. In addition, tensile specimens of FS-85, ASTAR-811C, T-111, and Mo-47.5 Re had been machined at Kin-Tech (North Huntington, PA). Actual machining of the other specimen types had not been initiated. Flowcharts 1-3 detail the major processing steps each piece of material has experienced. A more detailed description of processing will be provided in a separate document [B-MT(SRME)-51]. Table 1 lists the in-process materials and finished specimens. Also included are current metallurgical condition of these materials and specimens. The available chemical analyses for these alloys at various points in the process are provided in Table 2

Mechanical behaviour of U3O8-Al cermets

International Nuclear Information System (INIS)

Figueredo, A.M. de; Ferreira, I.

1981-01-01

Homogeneous, high density U 3 O 8 -Al cermets, containing between 5 W% and 55 Wt% of U 3 ω 8 were fabricated using hot swaging and powder metallurgy technics. Tensile tests were performed at room temperature on specimens obtained from the cermets fabricated. The results show that the ultimate tensile strength (UTS) and elongation to fracture decrease with increasing U 3 O 8 in the cermet. The UTS is shown to be proportional to the minimum matrix load bearing cross-sectional area. The main influence of an increase in the content of U 3 O 8 in the cermet appears to be the decrease in the minimum matrix, load bearing cross-section. (Author) [pt

Determination of the duration of heating and cooling of titanium alloy billets for swaging

International Nuclear Information System (INIS)

Kushakevich, S.A.; Konovalov, M.A.; Chistyakov, N.I.

1978-01-01

An attempt was made to establish a connection between the duration of heat and the decrease in metal temperature during deformation to determine the beginning and duration of heating titanium alloy billets for hot stamping. The investigations were made on the VT3-1 alloy billets with chromel-alumel thermocouples inside. The results of measurements of billet surface and center temperatures during the heating in a resistance surface up to 960-1050deg C and during the cooling in the air. It is shown that heating and cooling increase with the billet cross-section. The heating duration up to 1050deg C for all cross-sections is 4 or 5 min less than up to 960deg C. The cooling duration from 960 and 1050deg C to 200deg C depends weakly on the heating temperature and varies for various cross-sections within the limits of 1-2 min. It is proposed to determine roughly the metal temperature on complection of stamping through the time elapsed after the heated billet has left the furnace

Microstructural changes in zirconium alloy bar due to multi-roll straightening

International Nuclear Information System (INIS)

Gouraharidas; Acharya, Swaroop; Pratap, Y.; Chaube, R.K.; Kiran Kumar, I.; Ramana Rao, A.V.; Saibaba, N.

2010-01-01

Zirconium alloy bar is the input material for making of end plugs required for encapsulating the uranium di-oxide pellets in the fuel tubes. These bars are manufactured through extrusion followed by multi-pass swaging with intermediate and final vacuum annealing. The straightened and ground bars are subjected to 100% Ultrasonic testing and Eddy current testing to identify flaws and micro-porosity in the material, which could otherwise affect the integrity of fuel element. The defect standards at ultrasonic and eddy current inspection have been made more stringent, in view of the importance of fuel pin integrity during reactor operation. Consequently, many of the rods have shown eddy current indications greater than the defect standard. Detailed microstructural examination was carried out at each process step to identify the cause for these indications. Characteristic variation in the grain size and microstructure were noticed from surface to the centre of the material. Correlation between residual stresses and the eddy current signals was established. The extent of residual stresses could be controlled by adopting improvised straightening method at the final stage. This paper deals with the various trials carried out and the conclusions arrived at. (author)

THE COMBINED EFFECTS OF STRESS CONCENTRATION AND TENSILE STRESSES FROM AUTOFRETTAGE ON THE LIFE OF PRESSURE VESSELS

Science.gov (United States)

2017-02-22

information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing ... hydraulically or mechanically overstrained in order to impart favorable near bore residual compressive hoop stresses in an attempt to enhance fatigue life. As a...detrimental. In the early stages of development of each system, multiple full size vessels are hydraulically fatigue tested and a safe life is

The Combined Effects of Stress Concentration and Tensile Stresses from Autofrettage on the Life of Pressure Vessels

Science.gov (United States)

2017-02-01

Approved for public release; distribution is unlimited. 13. SUPPLEMENTARY NOTES 14. ABSTRACT Thick walled pressure vessels are often...studies which will identify the cause of the reduced lives and propose corrective action. 15. SUBJECT TERMS Thick Walled Pressure Vessels...are indicated, follow agency authorization procedures, e.g. RD/FRD, PROPIN, ITAR, etc. Include copyright information. 13. SUPPLEMENTARY NOTES

High-temperature strength of Nb-1%Zr alloy for irradiation-capsules inner-shell

International Nuclear Information System (INIS)

Nomura, Yasushi; Nakata, Hirokatsu; Tanaka, Mitsuo; Fukaya, Kiyoshi.

1978-04-01

Coated fuel particles in capsules will be irradiated at about 1600 0 C in JMTR. Nb-1%Zr alloy was chosen for inner shell material of the capsules because of its sufficient strength at 1000 0 C and low induced radioactivity. Nb-1%Zr ingot produced by electron beam melting was formed into seamless tubes by hollowing and swaging, followed by annealing. Creep test in helium flow and tensile test in vacuum were made to examine mechanical strength of the Nb-1%Zr tubes at 1000 0 C. Following are the results; 1) 0.2% yield stress at 1000 0 C is about 6 kg/mm 2 . 2) 3000 hr creep rupture stress at 1000 0 C is about 6 kg/mm 2 . (auth.)

Study on the overview on food borne bacteria in food with animal origin in Iran; Part three: seafood

Directory of Open Access Journals (Sweden)

S.S Shekarforoush

2013-02-01

Full Text Available The current retrospective study was focused on the contamination of seafood in Iran during the years 1999 to 2012. The isolates were Clostridium botulinum, Clostridium perferingense, Escherichia coli, Listeria monocytogenes, Salmonella, Shigella, Staphylococcus aureus and Vibrio parahemolyticus. C. botulinum type E was the most prevalent type of bacteria in the fisheries products, responsible for the most cases of botulinal food poisoning. The presence of coliforms and E. coli in the seafood was due to environmental pollution. Additionally, in the processed food, the contamination of potable water and poor handling of the products are the main sources. L. monocytogenes was isolated from fresh, frozen and processed food. The microorganism is able to grow in the refrigeration condition and multiply in the processed food. The temperature of cold smoking (20-30 ºC cannot stop growing of Listeria. High prevalence of Salmonella in water and fisheries product was mainly because of the low environmental sanitation and various geographical conditions. However, Compost fertilizer and flowing of the swages through the farms were considered as the major source of contamination. S. aureus is not a typical microorganism of the fisheries farms but may contaminate them during the processing or in-appropriate handling of the products. V. Parahemolyticus is a normal habitant organism of the pelagic area. The organism usually find in the warm water and presents in the tropical conditions. Different species of Vibrio may contaminate the salty water in the warm seasons and so contaminate the aquatics farms in these areas. In general, the prevalence of vibriosis was associated with the consumption of semi-cooked food stuff and/or the secondary contamination of the processed ones.

Ultrasonic measurements on residual stress in autofrettged thick walled petroleum pipes

International Nuclear Information System (INIS)

Woias, G.; Mizera, J.

2008-01-01

The residual stresses in a component or structure are caused by incompatible permanent deformation and related gradient of plastic/elastic strains. They may be generated or modified at every stage in the components life cycle, from original material production to final disposal. Residual stresses can be measured by non-destructive techniques, including X-ray and neutron diffraction, magnetic and ultrasonic methods. The selection of the optimum measurement technique should take account volumetric resolution, material, geometry and access to the component. For large metallic components neutron diffraction is of prime importance as it provides quantitative information on stresses in relatively large volume of methods disregarding its shape complexity. Residual stresses can play a significant role in explaining or preventing failure of components of industrial installations. One example of residual stresses preventing failure are the ones generated by shot peening, inducing surface compressive stresses that improve the fatigue life. Petroleum refinery piping is generally characterized by large-diameters, operated at elevated temperature and under high pressure. Pipelines of a polyethylene plant working in one of the Polish refineries are subjected to pressures exceeding 300 MPa at temperatures above 200 o C. The pipes considered here were pressurized with pressure of 600 MPa. The wall thickness of the pipes is 27 mm and pipe dimensions are 46 x 100 mm. The material is steel with Re=580 MPa. Due to pressurizing, the components retain compressive stresses at the internal surface. These stresses increase resistance to cracking of the pipes. Over the period of exploitation these stresses diminish due to temperature activated relaxation or creep. The purpose of the project is to verify kinetics of such a relaxation process and calibrate alternative methods of their measurements. To avoid stress relaxation, numerical analysis from Finite Element Modelling (FEM)gave an

Room temperature creep behavior of Ti–Nb–Ta–Zr–O alloy

Energy Technology Data Exchange (ETDEWEB)

Zhang, Wei-dong [State Key Laboratory of Powder Metallurgy, Central South University, Changsha, Hunan 410083 (China); Liu, Yong, E-mail: yonliu@csu.edu.cn [State Key Laboratory of Powder Metallurgy, Central South University, Changsha, Hunan 410083 (China); Wu, Hong; Lan, Xiao-dong [State Key Laboratory of Powder Metallurgy, Central South University, Changsha, Hunan 410083 (China); Qiu, Jingwen [College of Electrical and Mechanical Engineering, Hunan University of Science and Technology, Xiangtan, Hunan 411201 (China); Hu, Te [State Key Laboratory of Powder Metallurgy, Central South University, Changsha, Hunan 410083 (China); Tang, Hui-ping [State Key Laboratory of Porous Metal Materials, Northwestern Institute of Nonferrous Metal Research, Xi' an, Shaanxi 710012 (China)

2016-08-15

The room temperature creep behavior and deformation mechanisms of a Ti–Nb–Ta–Zr–O alloy, which is also called “gum metal”, were investigated with the nanoindentation creep and conventional creep tests. The microstructure was observed with electron backscattered diffraction analysis (EBSD) and transmission electron microscopy (TEM). The results show that the creep stress exponent of the alloy is sensitive to cold deformation history of the alloy. The alloy which was cold swaged by 85% shows high creep resistance and the stress exponent is approximately equal to 1. Microstructural observation shows that creep process of the alloy without cold deformation is controlled by dislocation mechanism. The stress-induced α' martensitic phase transformation also occurs. The EBSD results show that the grain orientation changes after the creep tests, and thus, the creep of the cold-worked alloy is dominated by the shear deformation of giant faults without direct assistance from dislocations. - Highlights: •Nanoindentation was used to investigate room temperature creep behavior of gum metal. •The creep stress exponent of gum metal is sensitive to the cold deformation history. •The creep stress exponent of cold worked gum metal is approximately equal to 1. •The creep of the cold-worked gum metal is governed by the shear deformation of giant faults.

Vibratory-compacted (vipac/sphere-pac) nuclear fuels - a comparison with pelletized nuclear fuels

Energy Technology Data Exchange (ETDEWEB)

Chidester, K.; Rubin, J. [Los Alamos National Lab., NM (United States); Thompson, M

2001-07-01

In order to achieve the packing densities required for nuclear fuel stability, economy and performance, the fuel material must be densified. This has traditionally been performed by high-temperature sintering. (At one time, fuel densification was investigated using cold/hot swaging. However, this fabrication method has become uncommon.) Alternatively, fuel can be densified by vibratory compaction (VIPAC). During the late 1950's and into the 1970's, in the U.S., vibratory compaction fuel was fabricated and test irradiated to evaluate its applicability compared to the more traditional pelletized fuel for nuclear reactors. These activities were primarily focused on light water reactors (LWR) but some work was performed for fast reactors. This paper attempts to summarize these evaluations and proposes to reconsider VIPAC fuel for future use. (author)

Vibratory-compacted (vipac/sphere-pac) nuclear fuels - a comparison with pelletized nuclear fuels

International Nuclear Information System (INIS)

Chidester, K.; Rubin, J.; Thompson, M.

2001-01-01

In order to achieve the packing densities required for nuclear fuel stability, economy and performance, the fuel material must be densified. This has traditionally been performed by high-temperature sintering. (At one time, fuel densification was investigated using cold/hot swaging. However, this fabrication method has become uncommon.) Alternatively, fuel can be densified by vibratory compaction (VIPAC). During the late 1950's and into the 1970's, in the U.S., vibratory compaction fuel was fabricated and test irradiated to evaluate its applicability compared to the more traditional pelletized fuel for nuclear reactors. These activities were primarily focused on light water reactors (LWR) but some work was performed for fast reactors. This paper attempts to summarize these evaluations and proposes to reconsider VIPAC fuel for future use. (author)

Designing high pressure containers for research- principles and applications

International Nuclear Information System (INIS)

Anandkumar, V.

1997-01-01

The high pressure scientist looks for a well engineered pressure apparatus for high pressure experiments for 1 kbar (0.1 GPa) and above. Often, a variety of difficulties including the choice of materials, design configuration, optimum utilisation of the strength of materials used in the design, are encountered. This article is intended to help the high pressure scientist to select the design approach for pressure retaining container. The limitations imposed by the strength of available materials and engineering standards in building high pressure containers are discussed. Engineering solutions to overcome these limitations with optimal utilisation of the strength of the materials are also discussed. Novel methods to boost up the pressure retaining capacity like multilayered design and autofrettaging are compared along with their relative advantages and disadvantages. Special methods by which it is possible to attain pressures which are several times the yield strength of the materials of construction are presented. In this aspects such as the basis of the codes and their relevance in the design of high pressure equipment will also be described. Discussions are centered around the methods to tackle situations where experimental constraints dictate requirements of pressures higher than those permitted by design codes. Safety features are also discussed. (author)

Production of superconducting Nb3Sn wire using Nb or Nb(Ti) and Sn(Ga) solid solution powders

International Nuclear Information System (INIS)

Thieme, C.L.H.; Foner, S.

1991-01-01

This paper reports on superconducting Nb 3 Sn wire produced by the powder metallurgy method using Nb or Nb-2.9 at% Ti powder in combination with Sn-x at% Ga powders (x = 3, 4.2, 6.2 and 9.0). Ga additions to the Sn caused considerable solid solution hardening which improved its workability. It made the Nb-Sn(Ga) powder combinations convenient for swaging and extensive wire drawing. Anneals at 950 degrees C produced wires with an overall J c of 10 4 A/cm 2 at 21.9 T for wires with both Ti in the Nb and 6.2 at% Ga in the Sn. Comparison of this wire with the best Nb(Ti)-Cu-internal Sn(Ti) shows a higher J c per A15 areas, especially in fields of 22T and above

The United States pit disassembly and conversion project -- Meeting the MOX fuel specification

International Nuclear Information System (INIS)

Nelson, T.O.; James, C.A.; Kolman, D.G.

1998-01-01

The US is actively involved in demonstrating the disassembly of nuclear weapons pits to an unclassified form readied for disposition. The MOX option is the most likely path forward for plutonium that originated from nuclear weapon pits. The US demonstration line for pit disassembly and conversion is known as ARIES, the advanced recovery and integrated extraction system. The ARIES demonstration line is being used to gather data in an integrated fashion of the technologies needed for pit disassembly and conversion. These activities include the following modules: pit bisection, hydride-dehydride, oxide conversion, canning, electrolytic decontamination, and nondestructive assay (NDA). Pit bisection swages in a pit in half. Hydride-dehydride converts the pit plutonium metal to an unclassified metal button. To convert the plutonium metal to an oxide the US is investigating a number of options. The primary oxide conversion approach involves variations of combining plutonium hydriding and subsequent oxidation. Another approach is to simply oxidize the metal under controlled conditions-direct metal oxidation (DMO). To remove the gallium from the plutonium oxide, a thermal distillation approach is being used. These pyrochemical approaches will substantially reduce the wastes produced for oxide conversion of weapon plutonium, compared to traditional aqueous processing. The packaging of either the plutonium metal or oxide to long term storage criteria involves the canning and electrolytic decontamination modules. The NDA suite of instruments is then used to assay the material in the containers, which enables international verification without the need to open the containers and repackage them. All of these processes are described

Mechanical properties of molybdenum alloyed liquid phase-sintered tungsten-based composites

International Nuclear Information System (INIS)

Kemp, P.B.; German, R.M.

1995-01-01

Tungsten-based composites are fabricated from mixed elemental powders using liquid phase sintering, usually with a nickel-iron matrix. During sintering, the tungsten undergoes grain growth, leading to microstructure coarsening that lowers strength but increases ductility. Often the desire is to increase strength at the sacrifice of ductility, and historically, this has been performed by postsintering deformation. There has been considerable research on alloying to adjust the as-sintered mechanical properties to match those of swaged alloys. Prior reports cover many additions, seemingly including much of the periodic table. Unfortunately, many of the modified alloys proved disappointing, largely due to degraded strength at the tungsten-matrix interface. Of these modified alloys, the molybdenum-containing systems exhibit a promising combination of properties, cost, and processing ease. For example, the 82W-8Mo-7Ni-3Fe alloy gives a yield strength that is 34% higher than the equivalent 90W-7Ni-3Fe alloy (from 535 to 715 MPa) but with a 33% decrease in fracture elongation (from 30 to 20% elongation). This article reports on experiments geared to promoting improved properties in the W-Mo-Ni-Fe alloys. However, unlike the prior research which maintained a constant Ni + Fe content and varied the W:Mo ratio, this study considers the Mo:(Ni + Fe) ratio effect for 82, 90, and 93 wt pct W

A collapse mode of failure in powder-filled fuel elements

International Nuclear Information System (INIS)

Feraday, M.A.; Chalder, G.H.

1964-01-01

Two swaged fuel elements containing crushed, fused UO 2 powder were irradiated in a pressurized water loop at high heat ratings (∫Kdθ = 48 w/cm). The fuel elements were 2.0 cm in diameter and were sheathed in nickel-free Zircaloy--2 of 0.038 cm thickness. One element failed when the sheath ruptured at the top of a longitudinal ridge in the sheath after a burn-up of approximately 2550 MWd/TeU. No evidence was found that outgassing of the UO 2 contributed to the failure. Dimensional and structural changes observed in the fuel elements led to the conclusion that ridging of the sheath resulted from the action of coolant pressure on the diametral clearance formed by sintering and shrinkage of the UO 2 . Failure resulted due to severe local deformation accompanying one or more power cycles following ridge formation. (author)

Effect of high content nano-thoria addition on the properties of tungsten electrode

International Nuclear Information System (INIS)

Wang Fazhan; Zhuge Fei; Zhang Hui; Ding Bingjun

2003-01-01

By hot swaging, the nano-composite W-4.5%ThO 2 cathode was fabricated. A comparative investigation has been made on the operation characteristics for a conventional W-2%ThO 2 cathode, a conventional W-4%ThO 2 cathode and a nano-composite W-4.5%ThO 2 cathode. The results showed that the arc starting and arc voltage-current characteristic of the nano-composite W-4.5%ThO 2 electrode was the best among the three cathodes. These operating characteristics depended on the content and the size of thoria. The anti-erosion ability of the nano-composite W-4.5%ThO 2 cathode was slightly better than that of conventional W-4%ThO 2 cathode, but was obviously improved as compared to W-2%ThO 2 cathode, indicating that the content of thoria governs the resistance to arc erosion of the electrodes

Structural fatigue test results for large wind turbine blade sections

Science.gov (United States)

Faddoul, J. R.; Sullivan, T. L.

1982-01-01

In order to provide quantitative information on the operating life capabilities of wind turbine rotor blade concepts for root-end load transfer, a series of cantilever beam fatigue tests was conducted. Fatigue tests were conducted on a laminated wood blade with bonded steel studs, a low cost steel spar (utility pole) with a welded flange, a utility pole with additional root-end thickness provided by a swaged collar, fiberglass spars with both bonded and nonbonded fittings, and, finally, an aluminum blade with a bolted steel fitting (Lockheed Mod-0 blade). Photographs, data, and conclusions for each of these tests are presented. In addition, the aluminum blade test results are compared to field failure information; these results provide evidence that the cantilever beam type of fatigue test is a satisfactory method for obtaining qualitative data on blade life expectancy and for identifying structurally underdesigned areas (hot spots).

The effect of boron addition on microstructure and mechanical properties of biomedical Ti35Nb6Ta alloy

Energy Technology Data Exchange (ETDEWEB)

Málek, Jaroslav, E-mail: malek@ujp.cz [UJP PRAHA a.s., Nad Kamínkou 1345, 156 10 Prague, Zbraslav (Czech Republic); CTU in Prague, Faculty of Mechanical Engineering, Department of Materials Engineering, Karlovo Namesti 13, 121 35 Praha 2 (Czech Republic); Hnilica, František, E-mail: hnilica@ujp.cz [UJP PRAHA a.s., Nad Kamínkou 1345, 156 10 Prague, Zbraslav (Czech Republic); Veselý, Jaroslav, E-mail: vesely@ujp.cz [UJP PRAHA a.s., Nad Kamínkou 1345, 156 10 Prague, Zbraslav (Czech Republic); Smola, Bohumil, E-mail: smola@met.mff.cuni.cz [Charles University, Faculty of Mathematics and Physics, Ke Karlovu 5, 121 16 Prague 2 (Czech Republic); Březina, Vítězslav, E-mail: brezinavita@gmail.com [Masaryk University, Faculty of Medicine, Department of Stomathology, Komenského Náměstí 220/2, 662 43 Brno (Czech Republic); Kolařík, Kamil, E-mail: kamil.kolarik@email.cz [Faculty of Mechanical Engineering, University of West Bohemia, Univerzitní 22, 306 14 Plzeň (Czech Republic)

2014-10-15

The beta-titanium alloys are promising materials for bioapplications but their processing via melting is difficult. Coarse grains have been observed in as-cast specimens. Subsequent thermo-mechanical processing seems to be necessary in order to obtain fine-grained microstructure with better mechanical properties. The grain size can be decreased significantly by addition of small boron amount. In this work Ti–35Nb–6Ta alloy with various B additions (0, 0.05, 0.1, 0.3 and 0.5 wt.%) has been studied. Even the smallest amount of B leads to significant grain refinement in Ti–35Nb–6Ta alloy (from 1300 to about 350 μm). Slight grain refinement has been observed also after hot forging and solution treatment. TiB particles emerged in specimens due to B addition. These particles contribute to changes in mechanical properties not only in hot forged and solution treated specimens (hardness increase from 140 to 180 HV10), but also in cold swaged specimens (hardness from 230 to 250 HV10, tensile strength from 800 to 920 MPa). The hardness values can be increased up to 370 HV10 during aging at 400 °C (specimen with 0.5 wt.% B). It has been observed that specimens with low boron addition 0.05 wt.% possess no cytotoxicity. On the other hand in specimens with 0.1 wt.% B or more slight adverse effect on cytotoxicity has been observed. - Highlights: • The influence of boron on microstructure and mechanical properties has been studied. • Beta-transus temperature has been determined. • Cytotoxicity depending on boron content has been evaluated. • Possibility of final heat treatment has been determined.

Materials considerations in accelerator targets

International Nuclear Information System (INIS)

Peacock, H.B. Jr.; Iyer, N.C.; Louthan, M.R. Jr.

1994-01-01

Future nuclear materials production and/or the burn-up of long lived radioisotopes may be accomplished through the capture of spallation produced neutrons in accelerators. Aluminum clad-lead and/or lead alloys has been proposed as a spallation target. Aluminum was the cladding choice because of the low neutron absorption cross section, fast radioactivity decay, high thermal conductivity, and excellent fabricability. Metallic lead and lead oxide powders were considered for the target core with the fabrication options being casting or powder metallurgy (PM). Scoping tests to evaluate gravity casting, squeeze casting, and casting and swaging processes showed that, based on fabricability and heat transfer considerations, squeeze casting was the preferred option for manufacture of targets with initial core cladding contact. Thousands of aluminum clad aluminum-lithium alloy core targets and control rods for tritium production have been fabricated by coextrusion processes and successfully irradiated in the SRS reactors. Tritium retention in, and release from the coextruded product was modeled from experimental and operational data. Newly produced tritium atoms were trapped by lithium atoms to form a lithium tritide. The effective tritium pressure required for trap or tritide stability was the equilibrium decomposition pressure of tritium over a lithium tritide-aluminum mixture. The temperature dependence of tritium release was determined by the permeability of the cladding to tritium and the local equilibrium at the trap sites. The model can be used to calculate tritium release from aluminum clad, aluminum-lithium alloy targets during postulated accelerator operational and accident conditions. This paper describes the manufacturing technologies evaluated and presents the model for tritium retention in aluminum clad, aluminum-lithium alloy tritium production targets

Surface modification of Ti-30Ta alloy by electrospun PCL deposition

Energy Technology Data Exchange (ETDEWEB)

Wada, C.M.; Rangel, A.L.R.; Souza, M.A. de; Claro, A.P.R.A.; Rezende, M.C.R. [Universidade Estadual Paulista Julio de Mesquita Filho (UNESP), SP (Brazil); Almeida, R. dos S. [Universidade Estadual de Campinas (UNICAMP), SP (Brazil)

2014-07-01

Full text: Surface modifications techniques have been used for change the inert surface of the titanium alloys for better interaction. Ingots of the experimental alloy Ti30Ta were melted in an arc furnace and re-melted ten times at least. They were homogenized under vacuum at 1000 °C for 86. 4 ks to eliminate chemical segregation and cold-worked by swaging. Discs were immersed in aqueous NaOH solution for 24 h, dried at room temperature, immersed in HCl and dried at 40 °C in oven for 24 hours. Followed, PCL fibers were deposited on the Ti30Ta alloy discs surfaces by electrospinning. Plasma treatment was carried out for change PCL electrospun by using stainless steel plasma reactor. Samples were immersed in SBF 5x solution for apatite growth. Surfaces were evaluated by using SEM, X-rays diffraction and contact angle. Samples exhibited hydrophilic behavior after plasma treatment and SBF immersion. Results are very interesting for biomedical applications. (author)

Surface modification of Ti-30Ta alloy by electrospun PCL deposition

International Nuclear Information System (INIS)

Wada, C.M.; Rangel, A.L.R.; Souza, M.A. de; Claro, A.P.R.A.; Rezende, M.C.R.; Almeida, R. dos S.

2014-01-01

Full text: Surface modifications techniques have been used for change the inert surface of the titanium alloys for better interaction. Ingots of the experimental alloy Ti30Ta were melted in an arc furnace and re-melted ten times at least. They were homogenized under vacuum at 1000 °C for 86. 4 ks to eliminate chemical segregation and cold-worked by swaging. Discs were immersed in aqueous NaOH solution for 24 h, dried at room temperature, immersed in HCl and dried at 40 °C in oven for 24 hours. Followed, PCL fibers were deposited on the Ti30Ta alloy discs surfaces by electrospinning. Plasma treatment was carried out for change PCL electrospun by using stainless steel plasma reactor. Samples were immersed in SBF 5x solution for apatite growth. Surfaces were evaluated by using SEM, X-rays diffraction and contact angle. Samples exhibited hydrophilic behavior after plasma treatment and SBF immersion. Results are very interesting for biomedical applications. (author)

Biological and chemical evaluation of sewage water pollution in the Rietvlei nature reserve wetland area, South Africa

International Nuclear Information System (INIS)

Oberholster, P.J.; Botha, A.-M.; Cloete, T.E.

2008-01-01

Macroinvertebrate communities in Rietvlei nature reserve wetland area and their relationship with water quality were studied with the aim to evaluate their use as potential indicators of pollution. Sampling locations were selected to include outlets from swage effluent, agricultural and informal residential runoff. A large increase in nutrient concentrations was observed downstream from discharged treated sewage with an associated decrease in species richness. Bioassays performed included: Daphnia magna, Hydra attenuate, Lactuca sativa, Allium cepa and Pyxicephalus adspersus. The highest percentage of lethality response to a screen (100% concentration) of sampled wetland water by test specimens were observed at the point source input of the Hartbeespoort treated sewage plant. Data generated from the AUSRIVAS method and multitrophic level bioassays revealed the deterioration of the wetland possibly due to factors such as increasing urbanization, industrialization, agriculture runoff and rapid human settlement in the Hennops River catchment area and its principal tributaries. - Bioassays confirmed the degradation of a freshwater wetland system due to effluent from a variety of sources

Biological and chemical evaluation of sewage water pollution in the Rietvlei nature reserve wetland area, South Africa

Energy Technology Data Exchange (ETDEWEB)

Oberholster, P.J. [CSIR Natural Resources and the Environment, P.O. Box 395, Pretoria 0001 (South Africa)], E-mail: anna.oberholster@up.ac.za; Botha, A.-M. [Department of Genetics, University of Pretoria, Hillcrest, Pretoria ZA002 (South Africa); Cloete, T.E. [Department of Microbiology and Plant Pathology, University of Pretoria, Hillcrest, Pretoria ZA002 (South Africa)

2008-11-15

Macroinvertebrate communities in Rietvlei nature reserve wetland area and their relationship with water quality were studied with the aim to evaluate their use as potential indicators of pollution. Sampling locations were selected to include outlets from swage effluent, agricultural and informal residential runoff. A large increase in nutrient concentrations was observed downstream from discharged treated sewage with an associated decrease in species richness. Bioassays performed included: Daphnia magna, Hydra attenuate, Lactuca sativa, Allium cepa and Pyxicephalus adspersus. The highest percentage of lethality response to a screen (100% concentration) of sampled wetland water by test specimens were observed at the point source input of the Hartbeespoort treated sewage plant. Data generated from the AUSRIVAS method and multitrophic level bioassays revealed the deterioration of the wetland possibly due to factors such as increasing urbanization, industrialization, agriculture runoff and rapid human settlement in the Hennops River catchment area and its principal tributaries. - Bioassays confirmed the degradation of a freshwater wetland system due to effluent from a variety of sources.

Method of fabricating a poision tube for reactor control rods

Energy Technology Data Exchange (ETDEWEB)

Mori, Yasuhiko; Yoshida, Toshimi; Masaoka, Isao; Naruse, Akisuke

1983-04-28

A method to unify the neutron absorbing performance, enhance the workability in the insertion of neutron absorber tube and further decrease the stresses acting on the neutron absorber coating tube is described. The neutron absorber coated rod comprising neutron absorbing substance and a metal pipe is fabricated by compressing a metal pipe filled with the neutron absorber. Specifically, neutron absorbing substance such as boron carbide powder or the like is filled in a metal pipe such as made of stainless steel tube by way of vibration packing or the like. Then, after heating the metal pipe, it is applied with compression working such as swaging into a fine tube to increase the packing density of the absorbing substance filled in the pipe to greater than 60% of the theoretical density and completely contacted closely to the inner wall of the pipe. The neutron absorber coated rod thus fabricated can be inserted to an external coating tube with ease at a predetermined gap.

Obtention of copper-magnesium alloys wires used in electrical transmission lines

International Nuclear Information System (INIS)

Fernandes, Marcos Gonzales

2010-01-01

The aim of this work was to obtain copper wires in three different chemical compositions starting from electrolytic copper and magnesium. The mains steps were evaluated, starting from the melting of small eutectic cooper-magnesium specimens in an electric arc furnace, followed by further dilution of this buttons in a resistive furnace and casting it in a copper mould. The as cast billets were homogenized in a resistive furnace at 910 degree C for 2 h. The billets were mechanically cold worked by swaging and a final drawing step to attain a round shape and a reasonable surface quality. The cast ingots chemical analysis indicated that the processing route showed to be adequate, in laboratory scale, to obtain wires with cross sectional area of 4 mm2 and 10 m in length. The wires in both conditions - as cold worked and after a recovering heat treatment at 510 degree C for 1 h, were mechanically characterized by tensile testing and hardness. The wires had also the electric conductivity assessed in the recovered heat-treated state and the results were compared to the literature data. The obtained material showed to be adequate to be used as electric conductor. The yield strain and ultimate tensile strength were improved with the increasing amount of Mg in the alloy, 11 % and 24 %, respectively, while the electric conductivity decreased to 60 % IACS (International Annealed Copper Standard). (author)

Atomics International fuel fabrication facility and low enrichment program [contributed by T.A. Moss, AI

International Nuclear Information System (INIS)

Moss, T.A.

1993-01-01

The AI facility is approximately 30,000 square feet in area and consists of four general areas. One area is devoted to the production of UAl x powder. It consists of a series of arc melting furnaces, crushing lines, glove boxes, and compacting presses. The second area is used for the rolling of fuel plates. The third area is used for the machining of the plates to final size and also the machining of the fuel elements. In the fourth area the fuel plates are swaged into assemblies, and all welding and inspection operations are performed. As part of the lower enrichment program we are scheduled to put a second UAl x powder line into operation and we have had to expand some of our storage area. Under the low enrichment program the AI fuel facility will be modified to accommodate a separate low enrichment Al x production line and compacting line. This facility modification should be done by the end of the fiscal year. We anticipate producing fuel with an enrichment slightly less than 20% We anticipate powder being available for plate production shortly after the facility is completed. Atomics International is scheduled to conduct plate LEU verification work using fully enriched material in the June-July time period, at which time we will investigate what level of uranium loadings we can go to using the current process. It is anticipated that 55 volume percent uranium compound in our fuel form can be achieved

Influence of residual stresses during eddy current testing of zircaloy bar material

International Nuclear Information System (INIS)

Saibaba, N.; Das, G.; Pratap, Y.; Acharya, S.; Chaube, R.K.; Jayaraj, R.N.

2009-01-01

Full text: Zirconium alloy bar is the input material for making end plugs required for encapsulating the fuel tubes after loading of uranium di-oxide pellets. These bars are manufactured through extrusion followed by multi-pass swaging and intermediate vacuum annealing. The bar is subjected to 100% Ultrasonic testing to ensure that defect free material is used for making the end plugs. The elements thus welded are subjected to helium leak testing for checking the weld integrity. However, stray cases of helium leakage from fuel elements were observed on few occasions. On investigation, it was found that the leakage was from small porosity present in the plugs. In order to isolate such an eventuality, stricter ultrasonic standards were adopted and additionally eddy current testing was introduced. It was observed that a number of eddy current signals equal to the defect standard were noticed and the reasons for these indications could not be identified. This led to a significant fall in the material recovery. An in-depth study with various heat treatment cycles and process steps was carried out. It was finally concluded that the indications observed in eddy current testing were due to the residual stresses on the periphery of the bar material caused due by improper straightening being carried out at the final stage of the bar manufacture. This paper presents the systematic studies carried out and correlation established between the eddy current signals and the residual stresses

Californium-252 radiotherapy sources for interstitial afterloading

International Nuclear Information System (INIS)

Permar, P.H.; Walker, V.W.

1976-01-01

Californium-252 neutron sources for interstitial afterloading were developed to investigate the value of this radionuclide in cancer therapy. Californium-252 seed assemblies contain essentially point sources of 252 Cf permanently sealed on 1-cm centers within a flexible plastic tube. The seed assemblies are fabricated with remotely operated, specially designed machines. The fabrication process involves the production of a Pt-10 percent Ir-clad wire with a 252 Cf 2 O 3 -Pd cermet core. The wire is swaged and drawn to size, cut to length, and welded in a Pt-10 percent Ir capsule 0.8 mm in diameter and 6 mm long. Each seed capsule contains approximately 0.5 microgram of 252 Cf. Because the effective half-life of 252 Cf is 2.6 years, the seed assemblies are not disposable and must be reused until their activities have decreased to unsuitable levels. The flexible plastic components must therefore have sufficient resistance to radiation damage to survive the neutron-plus-gamma radiation from 252 Cf. On the basis of accelerated irradiation tests with a large 252 Cf source, a recently developed fluoropolymer, ''Tefzel'' (trademark of E. I. du Pont de Nemours and Company) has adequate radiation resistance for this application. Californium-252 seed assembly systems are loaned by the United States Energy Research and Development Administration for clinical investigations under a protocol of the Radiation Therapy Oncology Group, U.S. National Cancer Institute

Structure-property relationships in an Al matrix Ca nanofilamentary composite conductor with potential application in high-voltage power transmission

Science.gov (United States)

Tian, Liang

This study investigated the processing-structure-properties relationships in an Al/Ca composites using both experiments and modeling/simulation. A particular focus of the project was understanding how the strength and electrical conductivity of the composite are related to its microstructure in the hope that a conducting material with light weight, high strength, and high electrical conductivity can be developed to produce overhead high-voltage power transmission cables. The current power transmission cables (e.g., Aluminum Conductor Steel Reinforced (ACSR)) have acceptable performance for high-voltage AC transmission, but are less well suited for high-voltage DC transmission due to the poorly conducting core materials that support the cable weight. This Al/Ca composite was produced by powder metallurgy and severe plastic deformation by extrusion and swaging. The fine Ca metal powders have been produced by centrifugal atomization with rotating liquid oil quench bath, and a detailed study about the atomization process and powder characteristics has been conducted. The microstructure of Al/Ca composite was characterized by electron microscopy. Microstructure changes at elevated temperature were characterized by thermal analysis and indirect resistivity tests. The strength and electrical conductivity were measured by tensile tests and four-point probe resistivity tests. Predicting the strength and electrical conductivity of the composite was done by micro-mechanics-based analytical modeling. Microstructure evolution was studied by mesoscale-thermodynamics-based phase field modeling and a preliminary atomistic molecular dynamics simulation. The application prospects of this composite was studied by an economic analysis. This study suggests that the Al/Ca (20 vol. %) composite shows promise for use as overhead power transmission cables. Further studies are needed to measure the corrosion resistance, fatigue properties and energized field performance of this composite.

Validation of structural design of JHR fuel element

International Nuclear Information System (INIS)

Brisson, S.; Miras, G.; Le Bourdonnec, L.; Lemoine, P.; Anselmet, M.C.; Marelle, V.

2010-01-01

The validation of the structural design of the Jules Horowitz Reactor fuel element was made by the Finite Element Method, starting from the Computer Aided Design. The JHR fuel element is a cylindrical assembly of three sectors composed of eight rolled fuel plates. A roll-swaging process is used to join the fuel plates to three aluminium stiffeners. The hydraulic gap between each plate is 1.95 mm. The JHR fuel assembly is fastened at both ends to the upper and lower endfittings by riveting. The main stresses are essentially thermal loads, imposed on the fuel zone of the plates. These thermal loads result from the nuclear heat flux (W/cm 2 ). The mechanical loads are mainly hydraulic thrust forces. The average coolant velocity is 15 m/s. Seismic effects are also studied. The fuel assembly is entirely modelled by thin shells. The model takes into account asymmetric thermal loads which often appear in Research Reactors. The mechanics of the fuel plates vary in function of the burn up. These mechanical properties are derived from the data sets used in the MAIA code, and the validity of the structure is demonstrable at throughout the life of the fuel. Results concerning displacement are compared to functional criteria, while results concerning stress are compared to RCC-MX criteria. The results of this analysis show that the mechanical and geometrical integrity of the JHR fuel elements is respected for Operating Categories 1 and 2. This paper presents the methodology of this demonstration for the results obtained. (author)

The effect of the solute on the structure, selected mechanical properties, and biocompatibility of Ti–Zr system alloys for dental applications

International Nuclear Information System (INIS)

Correa, D.R.N.; Vicente, F.B.; Donato, T.A.G.; Arana-Chavez, V.E.; Buzalaf, M.A.R.; Grandini, C.R.

2014-01-01

New titanium alloys have been developed with the aim of utilizing materials with better properties for application as biomaterials, and Ti–Zr system alloys are among the more promising of these. In this paper, the influence of zirconium concentrations on the structure, microstructure, and selected mechanical properties of Ti–Zr alloys is analyzed. After melting and swaging, the samples were characterized through chemical analysis, density measurements, X-ray diffraction, optical microscopy, Vickers microhardness, and elasticity modulus. In-vitro cytotoxicity tests were performed on cultured osteogenic cells. The results showed the formation essentially of the α′ phase (with hcp structure) and microhardness values greater than cp-Ti. The elasticity modulus of the alloys was sensitive to the zirconium concentrations while remaining within the range of values of conventional titanium alloys. The alloys presented no cytotoxic effects on osteoblastic cells in the studied conditions. - Highlights: • Ti–Zr alloys for biomedical applications were developed. • Only α′ phase was observed. • Influence of zirconium concentrations on the properties of Ti–Zr alloys was analyzed. • No cytotoxic effects were observed

A novel method for shape analysis: deformation of bubbles during wire drawing in doped tungsten

International Nuclear Information System (INIS)

Harmat, P.; Bartha, L.; Grosz, T.; Rosta, L.

2001-01-01

A novel technique has been developed for monitoring shape and size of microscopic pores, bubbles, second phase particles in deformed PM materials. The anisotropic small angle neutron scattering (ASANS) measurement provides direct visualization of the shape of second phase objects after rolling, swaging, wire drawing. Also in case of mixture of different objects e. g. uniformly elongated bubbles and spherical ones they can be separated and their morphological parameters like relative number density, diameter, aspect ratio can be obtained from the quantitative analysis of ASANS data. Rods and wires from K-AI-Si doped tungsten containing residual porosity and K filled bubbles were studied from 6 mm to 0.2 mm in diameter. The increase of the average aspect ratio (∼1/d) was found to be much slower than expected from the usual theory (∼1/d 3 ). Instead of 'constant volume' assumption, the 'constant length' seems to be reliable. The ASANS investigation revealed also the occurrence of a small amount of spherical bubbles after several steps of wire drawing. (author)

The effect of the solute on the structure, selected mechanical properties, and biocompatibility of Ti–Zr system alloys for dental applications

Energy Technology Data Exchange (ETDEWEB)

Correa, D.R.N.; Vicente, F.B. [UNESP — Univ. Estadual Paulista, Laboratório de Anelasticidade e Biomateriais, 17.033-360, Bauru, SP (Brazil); Donato, T.A.G.; Arana-Chavez, V.E. [USP — Universidade de São Paulo, Faculdade de Odontologia, Departamento de Biologia Oral e Biomateriais, 05.508-900, São Paulo, SP (Brazil); Buzalaf, M.A.R. [USP — Universidade de São Paulo, Faculdade de Odontologia de Bauru, Departamento de Ciências Biológicas, 17.012-901, Bauru, SP (Brazil); Grandini, C.R., E-mail: betog@fc.unesp.br [UNESP — Univ. Estadual Paulista, Laboratório de Anelasticidade e Biomateriais, 17.033-360, Bauru, SP (Brazil)

2014-01-01

New titanium alloys have been developed with the aim of utilizing materials with better properties for application as biomaterials, and Ti–Zr system alloys are among the more promising of these. In this paper, the influence of zirconium concentrations on the structure, microstructure, and selected mechanical properties of Ti–Zr alloys is analyzed. After melting and swaging, the samples were characterized through chemical analysis, density measurements, X-ray diffraction, optical microscopy, Vickers microhardness, and elasticity modulus. In-vitro cytotoxicity tests were performed on cultured osteogenic cells. The results showed the formation essentially of the α′ phase (with hcp structure) and microhardness values greater than cp-Ti. The elasticity modulus of the alloys was sensitive to the zirconium concentrations while remaining within the range of values of conventional titanium alloys. The alloys presented no cytotoxic effects on osteoblastic cells in the studied conditions. - Highlights: • Ti–Zr alloys for biomedical applications were developed. • Only α′ phase was observed. • Influence of zirconium concentrations on the properties of Ti–Zr alloys was analyzed. • No cytotoxic effects were observed.

Influence of the chemical composition and temperature in the mechanical behaviour of U3O8-Al cermets

International Nuclear Information System (INIS)

Ferreira, P.I.; Figueredo, A.M. de

1982-01-01

U 3 O 8 -Al nuclear cermets, with U 3 O 8 content varying from zero to 80 wt%, were prepared by rotary swaging of U 3 O 8 -Al compacts at 500 0 C. Specimens were fabricated from these materials and tensile tested at the temperatures 25 0 , 200 0 , 300 0 and 400 0 C at a strain rate of 4.3 x 10 - 5 s - 1 . The yield stress σ sub(E) and the ultimate tensile strength σ sub(R), were analysed as a function of the test temperature and cermet composition. The results show that the dependence of σ sub(E) and σ sub(R) on composition can be explained in terms of the variation of the minimum load bearing cross-sectional area of the aluminum matrix with U 3 O 8 concentration. The temperature dependence of σ sub(R) and σ sub(E) of the cermets was seen to be similar to the temperature dependence of these parameters of the aluminum matrix. (Author) [pt

Microstructural and mechanical characterization of biomedical Ti-Nb-Zr(-Ta) alloys

International Nuclear Information System (INIS)

Elias, L.M.; Schneider, S.G.; Schneider, S.; Silva, H.M.; Malvisi, F.

2006-01-01

In recent years there has been a significant development of novel implant alloys based on β-Ti such as Ti-Nb-Zr and Ti-Nb-Zr-Ta alloys systems. The purpose of this work is to provide characterization of Ti-35.3Nb-5.1Ta-7.1Zr and Ti-41.1Nb-7.1Zr alloys, in which Nb will substitute the atomic amount of Ta, with emphasis in the property-microstructure-composition relationships. These alloys are produced from commercially pure materials (Ti, Nb, Zr and Ta) by an arc melting method. All ingots were submitted to sequences of heat treatment (1000 deg. C/2 h - WQ), cold working by swaging procedures and other heat treatment (1000 deg. C/2 h - WQ). Specimens, in as cast and heat-treated condition, were examined by light and scanning electron microscopy (SEM). These results suggested the presence of β- and ω-phases. Mechanical properties were based on tensile and hardness tests. These alloys exhibit a lower modulus than that of conventional Ti alloys and the other mechanical properties are suitable for biomedical applications

AN ADVANCED OXIDATION PROCESS : FENTON PROCESS

Directory of Open Access Journals (Sweden)

Engin GÜRTEKİN

2008-03-01

Full Text Available Biological wastewater treatment is not effective treatment method if raw wastewater contains toxic and refractory organics. Advanced oxidation processes are applied before or after biological treatment for the detoxification and reclamation of this kind of wastewaters. The advanced oxidation processes are based on the formation of powerful hydroxyl radicals. Among advanced oxidation processes Fenton process is one of the most promising methods. Because application of Fenton process is simple and cost effective and also reaction occurs in a short time period. Fenton process is applied for many different proposes. In this study, Fenton process was evaluated as an advanced oxidation process in wastewater treatment.

Stress concentration factors for pressurized elliptic crossbores in blocks

International Nuclear Information System (INIS)

Badr, Elie A.

2006-01-01

Intersecting bore geometries are used in a number of industrial applications including heavy-walled pressure vessels containing oil holes for lubrication, ports for valves and fluid ends of reciprocating pumps. The bore intersection location is a stress concentration point where the maximum hoop stress can be many times the fluid pressure in the bores. Intersecting circular holes in heavy-walled cylinders and rectangular blocks have been extensively investigated. Specifically, stress/pressure concentration curves for intersecting circular bores in rectangular blocks were presented by Sorem et al. [Sorem JR, Shadley JR, Tipton SM. Design curves for maximum stresses in blocks containing pressurized bore intersections. ASME J Mech Des 1990; 113: 427-31.]. However, stress/pressure concentrations due to intersecting elliptic bores have not been broadly investigated. With the availability of computer numerical control (CNC) machinery, bores with elliptic crosssection can be produced with relative ease. In this paper, hoop stress concentration ratios are developed for elliptic crossbores in rectangular blocks. Results indicate that introducing elliptic crossbores, rather than circular ones, significantly reduces the hoop stress concentration factor at the crossbore intersection. Also, the presence of intersecting crossbores has a major effect on the fatigue life of pressure vessels [Badr EA, Sorem JR, Jr Tipton SM. Evaluation of the autofrettage effect on fatigue lives of steel blocks with crossbores using a statistical and a strain-based method. ASTM J Test Eval 2000; 28: 181-8.] and the reduction of hoop stress concentration is expected to enhance the fatigue life of pressure vessels containing crossbores

Control system for technological processes in tritium processing plants with process analysis

International Nuclear Information System (INIS)

Retevoi, Carmen Maria; Stefan, Iuliana; Balteanu, Ovidiu; Stefan, Liviu; Bucur, Ciprian

2005-01-01

Integration of a large variety of installations and equipment into a unitary system for controlling the technological process in tritium processing nuclear facilities appears to be a rather complex approach particularly when experimental or new technologies are developed. Ensuring a high degree of versatility allowing easy modifications in configurations and process parameters is a major requirement imposed on experimental installations. The large amount of data which must be processed, stored and easily accessed for subsequent analyses imposes development of a large information network based on a highly integrated system containing the acquisition, control and technological process analysis data as well as data base system. On such a basis integrated systems of computation and control able to conduct the technological process could be developed as well protection systems for cases of failures or break down. The integrated system responds to the control and security requirements in case of emergency and of the technological processes specific to the industry that processes radioactive or toxic substances with severe consequences in case of technological failure as in the case of tritium processing nuclear plant. In order to lower the risk technological failure of these processes an integrated software, data base and process analysis system are developed, which, based on identification algorithm of the important parameters for protection and security systems, will display the process evolution trend. The system was checked on a existing plant that includes a removal tritium unit, finally used in a nuclear power plant, by simulating the failure events as well as the process. The system will also include a complete data base monitoring all the parameters and a process analysis software for the main modules of the tritium processing plant, namely, isotope separation, catalytic purification and cryogenic distillation

Transmission electron microscopy of aged Ti-10Mo-20Nb alloy after hot swaging; Microscopia eletronica de transmissao da liga Ti-10Mo-20Nb envelhecida apos forjamento a quente

Energy Technology Data Exchange (ETDEWEB)

Gabriel, Sinara Borborema, E-mail: sinarab@msn.com [Universidade Federal do Rio de Janeiro (UFRJ), Rio de Janeiro, RJ (Brazil); Baldan, Renato, E-mail: renatobaldan@gmail.com [Universidade de Sao Paulo (EEL/USP), Lorena, SP (Brazil). Escola de Engenharia; Torres, Juliana; Oliveira, Nathalia Rodrigues, E-mail: juliana_torres_5@hotmail.com, E-mail: nathalia_roliveira@yahoo.com.br [Centro Universitario de Volta Redonda (UNIFOA), Volta Redonda, RJ (Brazil); Nunes, Carlos Angelo; Mei, Paulo Roberto, E-mail: cnunes@demar.eel.usp.br, E-mail: pmei@fem.unicamp.br [Universidade Estadual de Campinas (UNICAMP), Campinas, SP (Brazil)

2014-08-15

Ti alloys are widely used in biomedical applications. Within this class, metastable β -Ti alloys stand, because through thermomechanical processing it is possible to obtain mechanical properties and in particular one suitable Young's modulus for biomedical applications. These alloys require high mechanical strength and a low Young's modulus to avoid stress shielding. Preliminary studies showed that the microstructure of the Ti-10Mo- 20Nb alloy after cold forging and aging 500 °C/24 h consisted in bimodal distribution of α phase in the β matrix. The aim of this study was to characterize the microstructure of Ti-10Mo-20Nb alloy after hot forging and aging at 500 °C for 24 hours. Microstructural characterization consisted of analyzes by X-ray diffraction and transmission electron microscopy. According to the results, while the cold forging resulted in a bimodal α distribution in the β matrix, hot forging resulted in a thin and homogeneous α precipitation in the β matrix. (author)

Markov Processes in Image Processing

Science.gov (United States)

Petrov, E. P.; Kharina, N. L.

2018-05-01

Digital images are used as an information carrier in different sciences and technologies. The aspiration to increase the number of bits in the image pixels for the purpose of obtaining more information is observed. In the paper, some methods of compression and contour detection on the basis of two-dimensional Markov chain are offered. Increasing the number of bits on the image pixels will allow one to allocate fine object details more precisely, but it significantly complicates image processing. The methods of image processing do not concede by the efficiency to well-known analogues, but surpass them in processing speed. An image is separated into binary images, and processing is carried out in parallel with each without an increase in speed, when increasing the number of bits on the image pixels. One more advantage of methods is the low consumption of energy resources. Only logical procedures are used and there are no computing operations. The methods can be useful in processing images of any class and assignment in processing systems with a limited time and energy resources.

Thinning spatial point processes into Poisson processes

DEFF Research Database (Denmark)

Møller, Jesper; Schoenberg, Frederic Paik

, and where one simulates backwards and forwards in order to obtain the thinned process. In the case of a Cox process, a simple independent thinning technique is proposed. In both cases, the thinning results in a Poisson process if and only if the true Papangelou conditional intensity is used, and thus can......This paper describes methods for randomly thinning certain classes of spatial point processes. In the case of a Markov point process, the proposed method involves a dependent thinning of a spatial birth-and-death process, where clans of ancestors associated with the original points are identified...... be used as a diagnostic for assessing the goodness-of-fit of a spatial point process model. Several examples, including clustered and inhibitive point processes, are considered....

Process validation for radiation processing

International Nuclear Information System (INIS)

Miller, A.

1999-01-01

Process validation concerns the establishment of the irradiation conditions that will lead to the desired changes of the irradiated product. Process validation therefore establishes the link between absorbed dose and the characteristics of the product, such as degree of crosslinking in a polyethylene tube, prolongation of shelf life of a food product, or degree of sterility of the medical device. Detailed international standards are written for the documentation of radiation sterilization, such as EN 552 and ISO 11137, and the steps of process validation that are described in these standards are discussed in this paper. They include material testing for the documentation of the correct functioning of the product, microbiological testing for selection of the minimum required dose and dose mapping for documentation of attainment of the required dose in all parts of the product. The process validation must be maintained by reviews and repeated measurements as necessary. This paper presents recommendations and guidance for the execution of these components of process validation. (author)

Thinning spatial point processes into Poisson processes

DEFF Research Database (Denmark)

Møller, Jesper; Schoenberg, Frederic Paik

2010-01-01

are identified, and where we simulate backwards and forwards in order to obtain the thinned process. In the case of a Cox process, a simple independent thinning technique is proposed. In both cases, the thinning results in a Poisson process if and only if the true Papangelou conditional intensity is used, and......In this paper we describe methods for randomly thinning certain classes of spatial point processes. In the case of a Markov point process, the proposed method involves a dependent thinning of a spatial birth-and-death process, where clans of ancestors associated with the original points......, thus, can be used as a graphical exploratory tool for inspecting the goodness-of-fit of a spatial point process model. Several examples, including clustered and inhibitive point processes, are considered....

Process correlation analysis model for process improvement identification.

Science.gov (United States)

Choi, Su-jin; Kim, Dae-Kyoo; Park, Sooyong

2014-01-01

Software process improvement aims at improving the development process of software systems. It is initiated by process assessment identifying strengths and weaknesses and based on the findings, improvement plans are developed. In general, a process reference model (e.g., CMMI) is used throughout the process of software process improvement as the base. CMMI defines a set of process areas involved in software development and what to be carried out in process areas in terms of goals and practices. Process areas and their elements (goals and practices) are often correlated due to the iterative nature of software development process. However, in the current practice, correlations of process elements are often overlooked in the development of an improvement plan, which diminishes the efficiency of the plan. This is mainly attributed to significant efforts and the lack of required expertise. In this paper, we present a process correlation analysis model that helps identify correlations of process elements from the results of process assessment. This model is defined based on CMMI and empirical data of improvement practices. We evaluate the model using industrial data.

Management of processes of electrochemical dimensional processing

Science.gov (United States)

Akhmetov, I. D.; Zakirova, A. R.; Sadykov, Z. B.

2017-09-01

In different industries a lot high-precision parts are produced from hard-processed scarce materials. Forming such details can only be acting during non-contact processing, or a minimum of effort, and doable by the use, for example, of electro-chemical processing. At the present stage of development of metal working processes are important management issues electrochemical machining and its automation. This article provides some indicators and factors of electrochemical machining process.

Chemical process engineering in the transuranium processing plant

International Nuclear Information System (INIS)

Collins, E.D.; Bigelow, J.E.

1976-01-01

Since operation of the Transuranium Processing Plant began, process changes have been made to counteract problems caused by equipment corrosion, to satisfy new processing requirements, and to utilize improved processes. The new processes, equipment, and techniques have been incorporated into a sequence of steps which satisfies all required processing functions

Managing Process Variants in the Process Life Cycle

NARCIS (Netherlands)

Hallerbach, A.; Bauer, Th.; Reichert, M.U.

2007-01-01

When designing process-aware information systems, often variants of the same process have to be specified. Each variant then constitutes an adjustment of a particular process to specific requirements building the process context. Current Business Process Management (BPM) tools do not adequately

The Inter-Agency programme on marine pollution

International Nuclear Information System (INIS)

Carvalho, F.P.

1998-01-01

The Global Programme of Action (GPA) for the Protection of the Marine Environment from Land-based Activities - as well as a number of international conventions (e.g., United Nations Convention on the Law of the Sea, the Oslo and Paris Conventions) and regional agreements - are addressing the needs, The GPA sets the obligations for, and aims at assisting the States to undertake, the monitoring of contaminants in the marine environment and to control and abate pollution sources. Included among the contaminants of major concern are persistent organic pollutants (e.g., pesticides and PCBs), heavy metals, petroleum hydrocarbons, radioactive substances, nutrients, swage, and litter. Effective surveillance of contaminants of the marine environment and control of pollution depend upon a number of factors, including appropriate institutional capacity in the countries. In recent years, many countries displayed increased attention to environmental issues and, gradually, infrastructures were developed and environmental protection regulations were put into place. This article reviews the global framework for assisting countries to upgrade their capabilities for analysing data related to the marine environment, and particularly focuses on services being provided by the IAEA's Marine Environment Laboratory (MEL) in Monaco

Study of a design criterion for 316L irradiated represented by a strain hardened material

International Nuclear Information System (INIS)

Gouin, H.

1999-01-01

The aim of this study is to analyse the consequence of radiation on different structure submitted to imposed displacement loading and for damages due to plastic instability or rupture. The main consequence of radiation is a material hardening with a ductility decrease. This effect is similar to initial mechanical hardening: the mechanical properties (determined on smooth tensile specimen) evolve in the same way while irradiation or mechanical hardening increase. So in this study, radiation hardening is simulated by mechanical hardening (swaging). Tests were carried out for which two damages were considered: plastic instability and rupture. These two damages were studied with initial mechanical hardening (5 tested hammering rate 0, 15, 25, 35 and 45% on 316L stainless steel). Likewise two types of loading were studied: tensile or bending loading on specimens with or without geometrical singularities (notches). From tensile tests, two deformation criteria are proposed for prevention against the two quoted damages. Numerical study is carried out allowing to confirm hypothesis made at the time of the tensile test result interpretation and to validate the rupture criterion by applying on bending test. (author)

Study of a design criterion for 316L irradiated represented by a strain hardened material; Etude d'un critere de dimensionnement d'un acier 316L irradie represente par un materiau ecroui

Energy Technology Data Exchange (ETDEWEB)

Gouin, H

1999-07-01

The aim of this study is to analyse the consequence of radiation on different structure submitted to imposed displacement loading and for damages due to plastic instability or rupture. The main consequence of radiation is a material hardening with a ductility decrease. This effect is similar to initial mechanical hardening: the mechanical properties (determined on smooth tensile specimen) evolve in the same way while irradiation or mechanical hardening increase. So in this study, radiation hardening is simulated by mechanical hardening (swaging). Tests were carried out for which two damages were considered: plastic instability and rupture. These two damages were studied with initial mechanical hardening (5 tested hammering rate 0, 15, 25, 35 and 45% on 316L stainless steel). Likewise two types of loading were studied: tensile or bending loading on specimens with or without geometrical singularities (notches). From tensile tests, two deformation criteria are proposed for prevention against the two quoted damages. Numerical study is carried out allowing to confirm hypothesis made at the time of the tensile test result interpretation and to validate the rupture criterion by applying on bending test. (author)

Cladding temperature measurement by thermocouples at preirradiated LWR fuel rod samples

International Nuclear Information System (INIS)

Leiling, W.

1981-12-01

This report describes the technique to measure cladding temperatures of test fuel rod samples, applied during the in-pile tests on fuel rod failure in the steam loop of the FR2 reactor. NiCr/Ni thermocouples with stainless steel and Inconel sheaths, respectively,of 1 mm diameter were resistance spot weld to the outside of the fuel rod cladding. For the pre-irradiated test specimens, welding had to be done under hot-cell conditions, i.e. under remote handling. In order to prevent the formation of eutectics between zirconium and the chemical elements of the thermocouple sheath at elevated temperatures, the thermocouples were covered with a platinum jacket of 1.4 mm outside diameter swaged onto the sheath in the area of the measuring junction. This thermocouple design has worked satisfactorily in the in-pile experiments performed in a steam atmosphere. Even in the heatup phase, in which cladding temperatures up to 1050 0 C were reached, only very few failures occured. This good performance is to a great part due to a careful control and a thorough inspection of the thermocouples. (orig.) [de

Effects of Oil Shocks on the Unemployment: GVAR Approach

Directory of Open Access Journals (Sweden)

Malek KhojastehNeghad

2017-09-01

Full Text Available Oil is not only one of the most significant and useful consumer goods but also is a remarkable material in energy production all around the world which has a lot of price fluctuation. oil shocks consider as a principal factor of many financial crises and have various effects on economy of countries. Hence, the assessment of price fluctuations on macroeconomic variables such as unemployment seems important. This paper survey the oil price inconstancy on unemployment in 31countries during the period from the second quarter of 1985 to the fourth quarter of 2009 through Global Vector Auto-Regression model. Results demonstrate except of the rest of W. Europe, there is a positive relationship between oil prices oscillation and unemployment. It should be noted in many area the feedback along with the lag that depends on the ratio of oil cost in national income, reliance level to imported oil, end-users ability to reduce their usage and substitute other sources, gas consumption quantity in economy, effect of higher prices on other energy sources, monetary policies adopt when face with oil price swaging and capability of goverments to apply the vary policies.

Applications of Process Synthesis: Moving from Conventional Chemical Processes towards Biorefinery Processes

DEFF Research Database (Denmark)

Yuan, Zhihong; Chen, Bingzhen; Gani, Rafiqul

2013-01-01

Concerns about diminishing petroleum reserves, enhanced worldwide demand for fuels and fluctuations in the global oil market, together with climate change and national security have promoted many initiatives for exploring alternative, non-petroleum based processes. Among these initiatives......, biorefinery processes for converting biomass-derived carbohydrates into transportation fuels and chemicals are now gaining more and more attention from both academia and industry. Process synthesis, which has played a vital role for the development, design and operation of (petro) chemical processes, can...

Visualizing the process of process modeling with PPMCharts

NARCIS (Netherlands)

Claes, J.; Vanderfeesten, I.T.P.; Pinggera, J.; Reijers, H.A.; Weber, B.; Poels, G.; La Rosa, M.; Soffer, P.

2013-01-01

In the quest for knowledge about how to make good process models, recent research focus is shifting from studying the quality of process models to studying the process of process modeling (often abbreviated as PPM) itself. This paper reports on our efforts to visualize this specific process in such

Process Intensification: A Perspective on Process Synthesis

DEFF Research Database (Denmark)

Lutze, Philip; Gani, Rafiqul; Woodley, John

2010-01-01

In recent years, process intensification (PI) has attracted considerable academic interest as a potential means for process improvement, to meet the increasing demands for sustainable production. A variety of intensified operations developed in academia and industry creates a large number...... of options to potentially improve the process but to identify the set of feasible solutions for PI in which the optimal can be found takes considerable resources. Hence, a process synthesis tool to achieve PI would potentially assist in the generation and evaluation of PI options. Currently, several process...... design tools with a clear focus on specific PI tasks exist. Therefore, in this paper, the concept of a general systematic framework for synthesis and design of PI options in hierarchical steps through analyzing an existing process, generating PI options in a superstructure and evaluating intensified...

Perceptual Processing Affects Conceptual Processing

Science.gov (United States)

van Dantzig, Saskia; Pecher, Diane; Zeelenberg, Rene; Barsalou, Lawrence W.

2008-01-01

According to the Perceptual Symbols Theory of cognition (Barsalou, 1999), modality-specific simulations underlie the representation of concepts. A strong prediction of this view is that perceptual processing affects conceptual processing. In this study, participants performed a perceptual detection task and a conceptual property-verification task…

A process insight repository supporting process optimization

OpenAIRE

Vetlugin, Andrey

2012-01-01

Existing solutions for analysis and optimization of manufacturing processes, such as online analysis processing or statistical calculations, have shortcomings that limit continuous process improvements. In particular, they lack means of storing and integrating the results of analysis. This makes the valuable information that can be used for process optimizations used only once and then disposed. The goal of the Advanced Manufacturing Analytics (AdMA) research project is to design an integrate...

Two-stage process analysis using the process-based performance measurement framework and business process simulation

NARCIS (Netherlands)

Han, K.H.; Kang, J.G.; Song, M.S.

2009-01-01

Many enterprises have recently been pursuing process innovation or improvement to attain their performance goals. To align a business process with enterprise performances, this study proposes a two-stage process analysis for process (re)design that combines the process-based performance measurement

Continuous Correctness of Business Processes Against Process Interference

NARCIS (Netherlands)

van Beest, Nick; Bucur, Doina

2013-01-01

In distributed business process support environments, process interference from multiple stakeholders may cause erroneous process outcomes. Existing solutions to detect and correct interference at runtime employ formal verification and the automatic generation of intervention processes at runtime.

Materials considerations in accelerator targets

International Nuclear Information System (INIS)

Peacock, H. B. Jr.; Iyer, N. C.; Louthan, M. R. Jr.

1995-01-01

Future nuclear materials production and/or the burn-up of long lived radioisotopes may be accomplished through the capture of spallation produced neutrons in accelerators. Aluminum clad-lead and/or lead alloys has been proposed as a spallation target. Aluminum was the cladding choice because of the low neutron absorption cross section, fast radioactivity decay, high thermal conductivity, and excellent fabricability. Metallic lead and lead oxide powders were considered for the target core with the fabrication options being casting or powder metallurgy (PM). Scoping tests to evaluate gravity casting, squeeze casting, and casting and swaging processes showed that, based on fabricability and heat transfer considerations, squeeze casting was the preferred option for manufacture of targets with initial core cladding contact. Thousands of aluminum clad aluminum-lithium alloy core targets and control rods for tritium production have been fabricated by coextrusion processes and successfully irradiated in the SRS reactors. Tritium retention in, and release from, the coextruded product was modeled from experimental and operational data. The model assumed that tritium atoms, formed by the 6Li(n,a)3He reaction, were produced in solid solution in the Al-Li alloy. Because of the low solubility of hydrogen isotopes in aluminum alloys, the irradiated Al-Li rapidly became supersaturated in tritium. Newly produced tritium atoms were trapped by lithium atoms to form a lithium tritide. The effective tritium pressure required for trap or tritide stability was the equilibrium decomposition pressure of tritium over a lithium tritide-aluminum mixture. The temperature dependence of tritium release was determined by the permeability of the cladding to tritium and the local equilibrium at the trap sites. The model can be used to calculate tritium release from aluminum clad, aluminum-lithium alloy targets during postulated accelerator operational and accident conditions. This paper describes

Process mining: making knowledge discovery process centric

NARCIS (Netherlands)

Aalst, van der W.M.P.

2011-01-01

Recently, the Task Force on Process Mining released the Process Mining Manifesto. The manifesto is supported by 53 organizations and 77 process mining experts contributed to it. The active contributions from end-users, tool vendors, consultants, analysts, and researchers illustrate the growing

Business process model repositories : efficient process retrieval

NARCIS (Netherlands)

Yan, Z.

2012-01-01

As organizations increasingly work in process-oriented manner, the number of business process models that they develop and have to maintain increases. As a consequence, it has become common for organizations to have collections of hundreds or even thousands of business process models. When a

Aerodynamic isotope separation processes for uranium enrichment: process requirements

International Nuclear Information System (INIS)

Malling, G.F.; Von Halle, E.

1976-01-01

The pressing need for enriched uranium to fuel nuclear power reactors, requiring that as many as ten large uranium isotope separation plants be built during the next twenty years, has inspired an increase of interest in isotope separation processes for uranium enrichment. Aerodynamic isotope separation processes have been prominently mentioned along with the gas centrifuge process and the laser isotope separation methods as alternatives to the gaseous diffusion process, currently in use, for these future plants. Commonly included in the category of aerodynamic isotope separation processes are: (a) the separation nozzle process; (b) opposed gas jets; (c) the gas vortex; (d) the separation probes; (e) interacting molecular beams; (f) jet penetration processes; and (g) time of flight separation processes. A number of these aerodynamic isotope separation processes depend, as does the gas centrifuge process, on pressure diffusion associated with curved streamlines for the basic separation effect. Much can be deduced about the process characteristics and the economic potential of such processes from a simple and elementary process model. In particular, the benefit to be gained from a light carrier gas added to the uranium feed is clearly demonstrated. The model also illustrates the importance of transient effects in this class of processes

Business Process Innovation using the Process Innovation Laboratory

DEFF Research Database (Denmark)

Møller, Charles

for practical applications has not been identified. The aim of this paper is to establish a conceptual framework for business process innovation in the supply chain based on advanced enterprise systems. The main approach to business process innovation in this context is to create a new methodology for exploring...... process models and patterns of applications. The paper thus presents a new concept for business process innovation called the process innovation laboratory a.k.a. the ?-Lab. The ?-Lab is a comprehensive framework for BPI using advanced enterprise systems. The ?-Lab is a collaborative workspace...... for experimenting with process models and an explorative approach to study integrated modeling in a controlled environment. The ?-Lab facilitates innovation by using an integrated action learning approach to process modeling including contemporary technological, organizational and business perspectives....

Discovering Reference Process Models by Mining Process Variants

NARCIS (Netherlands)

Li, C.; Reichert, M.U.; Wombacher, Andreas

Recently, a new generation of adaptive Process-Aware Information Systems (PAIS) has emerged, which allows for dynamic process and service changes (e.g., to insert, delete, and move activities and service executions in a running process). This, in turn, has led to a large number of process variants

BUSINESS PROCESS REENGINEERING AS THE METHOD OF PROCESS MANAGEMENT

Directory of Open Access Journals (Sweden)

O. Honcharova

2013-09-01

Full Text Available The article is devoted to the analysis of process management approach. The main understanding of process management approach has been researched in the article. The definition of process and process management has been given. Also the methods of business process improvement has been analyzed, among them are fast-analysis solution technology (FAST, benchmarking, reprojecting and reengineering. The main results of using business process improvement have been described in figures of reducing cycle time, costs and errors. Also the tasks of business process reengineering have been noticed. The main stages of business process reengineering have been noticed. The main efficiency results of business process reengineering and its success factors have been determined.

Fundamentals of process intensification: A process systems engineering view

DEFF Research Database (Denmark)

Babi, Deenesh Kavi; Sales Cruz, Alfonso Mauricio; Gani, Rafiqul

2016-01-01

This chapter gives an overview of the fundamentals of process intensification from a process systems engineering point of view. The concept of process intensification, including process integration, is explained together with the drivers for applying process intensification, which can be achieved...

Idaho Chemical Processing Plant Process Efficiency improvements

International Nuclear Information System (INIS)

Griebenow, B.

1996-03-01

In response to decreasing funding levels available to support activities at the Idaho Chemical Processing Plant (ICPP) and a desire to be cost competitive, the Department of Energy Idaho Operations Office (DOE-ID) and Lockheed Idaho Technologies Company have increased their emphasis on cost-saving measures. The ICPP Effectiveness Improvement Initiative involves many activities to improve cost effectiveness and competitiveness. This report documents the methodology and results of one of those cost cutting measures, the Process Efficiency Improvement Activity. The Process Efficiency Improvement Activity performed a systematic review of major work processes at the ICPP to increase productivity and to identify nonvalue-added requirements. A two-phase approach was selected for the activity to allow for near-term implementation of relatively easy process modifications in the first phase while obtaining long-term continuous improvement in the second phase and beyond. Phase I of the initiative included a concentrated review of processes that had a high potential for cost savings with the intent of realizing savings in Fiscal Year 1996 (FY-96.) Phase II consists of implementing long-term strategies too complex for Phase I implementation and evaluation of processes not targeted for Phase I review. The Phase II effort is targeted for realizing cost savings in FY-97 and beyond

Process Accounting

OpenAIRE

Gilbertson, Keith

2002-01-01

Standard utilities can help you collect and interpret your Linux system's process accounting data. Describes the uses of process accounting, standard process accounting commands, and example code that makes use of process accounting utilities.

Modeling of biopharmaceutical processes. Part 2: Process chromatography unit operation

DEFF Research Database (Denmark)

Kaltenbrunner, Oliver; McCue, Justin; Engel, Philip

2008-01-01

Process modeling can be a useful tool to aid in process development, process optimization, and process scale-up. When modeling a chromatography process, one must first select the appropriate models that describe the mass transfer and adsorption that occurs within the porous adsorbent. The theoret......Process modeling can be a useful tool to aid in process development, process optimization, and process scale-up. When modeling a chromatography process, one must first select the appropriate models that describe the mass transfer and adsorption that occurs within the porous adsorbent...

Generalized Ornstein-Uhlenbeck processes and associated self-similar processes

CERN Document Server

Lim, S C

2003-01-01

We consider three types of generalized Ornstein-Uhlenbeck processes: the stationary process obtained from the Lamperti transformation of fractional Brownian motion, the process with stretched exponential covariance and the process obtained from the solution of the fractional Langevin equation. These stationary Gaussian processes have many common properties, such as the fact that their local covariances share a similar structure and they exhibit identical spectral densities at large frequency limit. In addition, the generalized Ornstein-Uhlenbeck processes can be shown to be local stationary representations of fractional Brownian motion. Two new self-similar Gaussian processes, in addition to fractional Brownian motion, are obtained by applying the (inverse) Lamperti transformation to the generalized Ornstein-Uhlenbeck processes. We study some of the properties of these self-similar processes such as the long-range dependence. We give a simulation of their sample paths based on numerical Karhunan-Loeve expansi...

Generalized Ornstein-Uhlenbeck processes and associated self-similar processes

International Nuclear Information System (INIS)

Lim, S C; Muniandy, S V

2003-01-01

We consider three types of generalized Ornstein-Uhlenbeck processes: the stationary process obtained from the Lamperti transformation of fractional Brownian motion, the process with stretched exponential covariance and the process obtained from the solution of the fractional Langevin equation. These stationary Gaussian processes have many common properties, such as the fact that their local covariances share a similar structure and they exhibit identical spectral densities at large frequency limit. In addition, the generalized Ornstein-Uhlenbeck processes can be shown to be local stationary representations of fractional Brownian motion. Two new self-similar Gaussian processes, in addition to fractional Brownian motion, are obtained by applying the (inverse) Lamperti transformation to the generalized Ornstein-Uhlenbeck processes. We study some of the properties of these self-similar processes such as the long-range dependence. We give a simulation of their sample paths based on numerical Karhunan-Loeve expansion

From Process Understanding to Process Control

NARCIS (Netherlands)

Streefland, M.

2010-01-01

A licensed pharmaceutical process is required to be executed within the validated ranges throughout the lifetime of product manufacturing. Changes to the process usually require the manufacturer to demonstrate that the safety and efficacy of the product remains unchanged. Recent changes in the

Integrated Process Modeling-A Process Validation Life Cycle Companion.

Science.gov (United States)

Zahel, Thomas; Hauer, Stefan; Mueller, Eric M; Murphy, Patrick; Abad, Sandra; Vasilieva, Elena; Maurer, Daniel; Brocard, Cécile; Reinisch, Daniela; Sagmeister, Patrick; Herwig, Christoph

2017-10-17

During the regulatory requested process validation of pharmaceutical manufacturing processes, companies aim to identify, control, and continuously monitor process variation and its impact on critical quality attributes (CQAs) of the final product. It is difficult to directly connect the impact of single process parameters (PPs) to final product CQAs, especially in biopharmaceutical process development and production, where multiple unit operations are stacked together and interact with each other. Therefore, we want to present the application of Monte Carlo (MC) simulation using an integrated process model (IPM) that enables estimation of process capability even in early stages of process validation. Once the IPM is established, its capability in risk and criticality assessment is furthermore demonstrated. IPMs can be used to enable holistic production control strategies that take interactions of process parameters of multiple unit operations into account. Moreover, IPMs can be trained with development data, refined with qualification runs, and maintained with routine manufacturing data which underlines the lifecycle concept. These applications will be shown by means of a process characterization study recently conducted at a world-leading contract manufacturing organization (CMO). The new IPM methodology therefore allows anticipation of out of specification (OOS) events, identify critical process parameters, and take risk-based decisions on counteractions that increase process robustness and decrease the likelihood of OOS events.

PC image processing

International Nuclear Information System (INIS)

Hwa, Mok Jin Il; Am, Ha Jeng Ung

1995-04-01

This book starts summary of digital image processing and personal computer, and classification of personal computer image processing system, digital image processing, development of personal computer and image processing, image processing system, basic method of image processing such as color image processing and video processing, software and interface, computer graphics, video image and video processing application cases on image processing like satellite image processing, color transformation of image processing in high speed and portrait work system.

Meat Processing.

Science.gov (United States)

Legacy, Jim; And Others

This publication provides an introduction to meat processing for adult students in vocational and technical education programs. Organized in four chapters, the booklet provides a brief overview of the meat processing industry and the techniques of meat processing and butchering. The first chapter introduces the meat processing industry and…

Process for improving metal production in steelmaking processes

Science.gov (United States)

Pal, Uday B.; Gazula, Gopala K. M.; Hasham, Ali

1996-01-01

A process and apparatus for improving metal production in ironmaking and steelmaking processes is disclosed. The use of an inert metallic conductor in the slag containing crucible and the addition of a transition metal oxide to the slag are the disclosed process improvements.

Genetic Process Mining: Alignment-based Process Model Mutation

NARCIS (Netherlands)

Eck, van M.L.; Buijs, J.C.A.M.; Dongen, van B.F.; Fournier, F.; Mendling, J.

2015-01-01

The Evolutionary Tree Miner (ETM) is a genetic process discovery algorithm that enables the user to guide the discovery process based on preferences with respect to four process model quality dimensions: replay fitness, precision, generalization and simplicity. Traditionally, the ETM algorithm uses

Business process modeling for processing classified documents using RFID technology

Directory of Open Access Journals (Sweden)

Koszela Jarosław

2016-01-01

Full Text Available The article outlines the application of the processing approach to the functional description of the designed IT system supporting the operations of the secret office, which processes classified documents. The article describes the application of the method of incremental modeling of business processes according to the BPMN model to the description of the processes currently implemented (“as is” in a manual manner and target processes (“to be”, using the RFID technology for the purpose of their automation. Additionally, the examples of applying the method of structural and dynamic analysis of the processes (process simulation to verify their correctness and efficiency were presented. The extension of the process analysis method is a possibility of applying the warehouse of processes and process mining methods.

Novel process windows, part 1: Boosted micro process technology

NARCIS (Netherlands)

Hessel, V.; Wang, Q.

2011-01-01

Novel Process Windows (NPW) is the use of highly intensified, unusual and typically harsh process conditions to boost micro process technology and flow chemistry for the production of high-added value fine chemicals, pharmaceuticals, etc.. It is far from conventional processing and also from

Durability Evaluation of a Thin Film Sensor System With Enhanced Lead Wire Attachments on SiC/SiC Ceramic Matrix Composites

Science.gov (United States)

Lei, Jih-Fen; Kiser, J. Douglas; Singh, Mrityunjay; Cuy, Mike; Blaha, Charles A.; Androjna, Drago

2000-01-01

An advanced thin film sensor system instrumented on silicon carbide (SiC) fiber reinforced SiC matrix ceramic matrix composites (SiC/SiC CMCs), was evaluated in a Mach 0.3 burner rig in order to determine its durability to monitor material/component surface temperature in harsh environments. The sensor system included thermocouples in a thin film form (5 microns thick), fine lead wires (75 microns diameter), and the bonds between these wires and the thin films. Other critical components of the overall system were the heavy, swaged lead wire cable (500 microns diameter) that contained the fine lead wires and was connected to the temperature readout, and ceramic attachments which were bonded onto the CMCs for the purpose of securing the lead wire cables, The newly developed ceramic attachment features a combination of hoops made of monolithic SiC or SiC/SiC CMC (which are joined to the test article) and high temperature ceramic cement. Two instrumented CMC panels were tested in a burner rig for a total of 40 cycles to 1150 C (2100 F). A cycle consisted of rapid heating to 1150 C (2100 F), a 5 minute hold at 1150 C (2100 F), and then cooling down to room temperature in 2 minutes. The thin film sensor systems provided repeatable temperature measurements for a maximum of 25 thermal cycles. Two of the monolithic SiC hoops debonded during the sensor fabrication process and two of the SiC/SiC CMC hoops failed during testing. The hoops filled with ceramic cement, however, showed no sign of detachment after 40 thermal cycle test. The primary failure mechanism of this sensor system was the loss of the fine lead wire-to-thin film connection, which either due to detachment of the fine lead wires from the thin film thermocouples or breakage of the fine wire.

Cognitive Processes in Discourse Comprehension: Passive Processes, Reader-Initiated Processes, and Evolving Mental Representations

Science.gov (United States)

van den Broek, Paul; Helder, Anne

2017-01-01

As readers move through a text, they engage in various types of processes that, if all goes well, result in a mental representation that captures their interpretation of the text. With each new text segment the reader engages in passive and, at times, reader-initiated processes. These processes are strongly influenced by the readers'…

Data processing

CERN Document Server

Fry, T F

2013-01-01

Data Processing discusses the principles, practices, and associated tools in data processing. The book is comprised of 17 chapters that are organized into three parts. The first part covers the characteristics, systems, and methods of data processing. Part 2 deals with the data processing practice; this part discusses the data input, output, and storage. The last part discusses topics related to systems and software in data processing, which include checks and controls, computer language and programs, and program elements and structures. The text will be useful to practitioners of computer-rel

In-process and post-process measurements of drill wear for control of the drilling process

Science.gov (United States)

Liu, Tien-I.; Liu, George; Gao, Zhiyu

2011-12-01

Optical inspection was used in this research for the post-process measurements of drill wear. A precision toolmakers" microscope was used. Indirect index, cutting force, is used for in-process drill wear measurements. Using in-process measurements to estimate the drill wear for control purpose can decrease the operation cost and enhance the product quality and safety. The challenge is to correlate the in-process cutting force measurements with the post-process optical inspection of drill wear. To find the most important feature, the energy principle was used in this research. It is necessary to select only the cutting force feature which shows the highest sensitivity to drill wear. The best feature selected is the peak of torque in the drilling process. Neuro-fuzzy systems were used for correlation purposes. The Adaptive-Network-Based Fuzzy Inference System (ANFIS) can construct fuzzy rules with membership functions to generate an input-output pair. A 1x6 ANFIS architecture with product of sigmoid membership functions can in-process measure the drill wear with an error as low as 0.15%. This is extremely important for control of the drilling process. Furthermore, the measurement of drill wear was performed under different drilling conditions. This shows that ANFIS has the capability of generalization.

Quasi-Birth-and-Death Processes with Rational Arrival Process Components

DEFF Research Database (Denmark)

Bean, Nigel G.; Nielsen, Bo Friis

to develop an analytic method for such a process, that parallels the analysis of a traditional QBD. We demonstrate the analysis by considering a queue where the arrival process and the sequence of service times are derived from two different RAPs that are not just Markovian Arrival processes. We also...... introduce an element of correlation between the arrival process and the sequence of service times.......In this paper we introduce the concept of a Quasi-Birth-and-Death process (QBD) with Rational Arrival Process components. We use the physical interpretation of a Rational Arrival Process (RAP), developed by Asmussen and Bladt, to consider such a Markov process. We exploit this interpretation...

Processes subject to integrated pollution control. Petroleum processes: oil refining and associated processes

International Nuclear Information System (INIS)

1995-01-01

This document, part of a series offering guidance on pollution control regulations issued by Her Majesty's Inspectorate of Pollution, (HMIP) focuses on petroleum processes such as oil refining and other associated processes. The various industrial processes used, their associated pollution release routes into the environment and techniques for controlling these releases are all discussed. Environmental quality standards are related to national and international agreements on pollution control and abatement. HMIP's work on air, water and land pollution monitoring is also reported. (UK)

Reflow process stabilization by chemical characteristics and process conditions

Science.gov (United States)

Kim, Myoung-Soo; Park, Jeong-Hyun; Kim, Hak-Joon; Kim, Il-Hyung; Jeon, Jae-Ha; Gil, Myung-Goon; Kim, Bong-Ho

2002-07-01

With the shrunken device rule below 130nm, the patterning of smaller contact hole with enough process margin is required for mass production. Therefore, shrinking technology using thermal reflow process has been applied for smaller contact hole formation. In this paper, we have investigated the effects of chemical characteristics such as molecular weight, blocking ratio of resin, cross-linker amount and solvent type with its composition to reflow process of resist and found the optimized chemical composition for reflow process applicable condition. And several process conditions like resist coating thickness and multi-step thermal reflow method have been also evaluated to stabilize the pattern profile and improve CD uniformity after reflow process. From the experiment results, it was confirmed that the effect of crosslinker in resist to reflow properties such as reflow temperature and reflow rate were very critical and it controlled the pattern profile during reflow processing. And also, it showed stable CD uniformity and improved resist properties for top loss, film shrinkage and etch selectivity. The application of lower coating thickness of resist induced symmetric pattern profile even at edge with wider process margin. The introduction of two-step baking method for reflow process showed uniform CD value, also. It is believed that the application of resist containing crosslinker and optimized process conditions for smaller contact hole patterning is necessary for the mass production with a design rule below 130nm.

Microcrystalline silicon deposition: Process stability and process control

International Nuclear Information System (INIS)

Donker, M.N. van den; Kilper, T.; Grunsky, D.; Rech, B.; Houben, L.; Kessels, W.M.M.; Sanden, M.C.M. van de

2007-01-01

Applying in situ process diagnostics, we identified several process drifts occurring in the parallel plate plasma deposition of microcrystalline silicon (μc-Si:H). These process drifts are powder formation (visible from diminishing dc-bias and changing spatial emission profile on a time scale of 10 0 s), transient SiH 4 depletion (visible from a decreasing SiH emission intensity on a time scale of 10 2 s), plasma heating (visible from an increasing substrate temperature on a time scale of 10 3 s) and a still puzzling long-term drift (visible from a decreasing SiH emission intensity on a time scale of 10 4 s). The effect of these drifts on the crystalline volume fraction in the deposited films is investigated by selected area electron diffraction and depth-profiled Raman spectroscopy. An example shows how the transient depletion and long-term drift can be prevented by suitable process control. Solar cells deposited using this process control show enhanced performance. Options for process control of plasma heating and powder formation are discussed

The permanent process

DEFF Research Database (Denmark)

Møller, Jesper; McCullagh, Peter

We extend the boson process first to a large class of Cox processes and second an even larger class of infinitely divisible point processes. Density and moment results are studied in detail. These results are obtained in closed form as weighted permanents, so the extension is called a permanent...... process. Temporal extensions and a particularly tractable case of the permanent process are also studied. Extensions of the ferminon process along similar lines, leading to so-called determinant processes, are discussed at the end. While the permanent process is attractive, the determinant process...

Multidimensional process discovery

NARCIS (Netherlands)

Ribeiro, J.T.S.

2013-01-01

Typically represented in event logs, business process data describe the execution of process events over time. Business process intelligence (BPI) techniques such as process mining can be applied to get strategic insight into business processes. Process discovery, conformance checking and

Process development

Energy Technology Data Exchange (ETDEWEB)

Schuegerl, K

1984-01-01

The item 'process development' comprises the production of acetonic/butonal with C. acetobylicum and the yeasting of potato waste. The target is to increase productivity by taking the following measures - optimation of media, on-line process analysis, analysis of reaction, mathematic modelling and identification of parameters, process simulation, development of a state estimator with the help of the on-line process analysis and the model, optimization and adaptive control.

Use of Raman Spectroscopy and Delta Volume Growth from Void Collapse to Assess Overwrap Stress Gradients Compromising the Reliability of Large Kevlar/Epoxy COPVs

Science.gov (United States)

Kezirian, Michael T.; Phoenix, S. Leigh; Eldridge, Jeffrey I.

2009-01-01

Composite Overwrapped Pressure Vessels (COPVs) are frequently used for storing pressurized gases aboard spacecraft and aircraft when weight saving is desirable compared to all-metal versions. Failure mechanisms in fibrous COPVs and variability in lifetime can be very different from their metallic counterparts; in the former, catastrophic stress-rupture can occur with virtually no warning, whereas in latter, a leak before burst design philosophy can be implemented. Qualification and certification typically requires only one burst test on a production sample (possibly after several pressure cycles) and the vessel need only meet a design burst strength (the maximum operating pressure divided by a knockdown factor). Typically there is no requirement to assess variability in burst strength or lifetime, much less determine production and materials processing parameters important to control of such variability. Characterizing such variability and its source is crucial to models for calculating required reliability over a given lifetime (e.g. R = 0.9999 for 15 years). In this paper we present a case study of how lack of control of certain process parameters in COPV manufacturing can result in variations among vessels and between production runs that can greatly increase uncertainty and reduce reliability. The vessels considered are 40-inch ( NASA Glenn Research center, Cleveland, OH, 44135 29,500 in3 ) spherical COPVs with a 0.74 in. thick Kevlar49/epoxy overwrap and with a titanium liner of which 34 were originally produced. Two burst tests were eventually performed that unexpectedly differed by almost 5%, and were 10% lower than anticipated from burst tests on 26-inch sister vessels similar in every detail. A major observation from measurements made during proof testing (autofrettage) of the 40-inch vessels was that permanent volume growth from liner yielding varied by a factor of more than two (150 in3 to 360 in3 ), which suggests large differences in the residual

Statistical Process Control for KSC Processing

Science.gov (United States)

Ford, Roger G.; Delgado, Hector; Tilley, Randy

1996-01-01

The 1996 Summer Faculty Fellowship Program and Kennedy Space Center (KSC) served as the basis for a research effort into statistical process control for KSC processing. The effort entailed several tasks and goals. The first was to develop a customized statistical process control (SPC) course for the Safety and Mission Assurance Trends Analysis Group. The actual teaching of this course took place over several weeks. In addition, an Internet version of the same course complete with animation and video excerpts from the course when it was taught at KSC was developed. The application of SPC to shuttle processing took up the rest of the summer research project. This effort entailed the evaluation of SPC use at KSC, both present and potential, due to the change in roles for NASA and the Single Flight Operations Contractor (SFOC). Individual consulting on SPC use was accomplished as well as an evaluation of SPC software for KSC use in the future. A final accomplishment of the orientation of the author to NASA changes, terminology, data format, and new NASA task definitions will allow future consultation when the needs arise.

A method for manufacturing a tool part for an injection molding process, a hot embossing process, a nano-imprint process, or an extrusion process

DEFF Research Database (Denmark)

2013-01-01

The present invention relates to a method for manufacturing a tool part for an injection molding process, a hot embossing process, nano-imprint process or an extrusion process. First, there is provided a master structure (10) with a surface area comprising nanometre-sized protrusions (11...

Process control using modern systems of information processing

International Nuclear Information System (INIS)

Baldeweg, F.

1984-01-01

Modern digital automation techniques allow the application of demanding types of process control. These types of process control are characterized by their belonging to higher levels in a multilevel model. Functional and technical aspects of the performance of digital automation plants are presented and explained. A modern automation system is described considering special procedures of process control (e.g. real time diagnosis)

DUAL-PROCESS, a highly reliable process control system

International Nuclear Information System (INIS)

Buerger, L.; Gossanyi, A.; Parkanyi, T.; Szabo, G.; Vegh, E.

1983-02-01

A multiprocessor process control system is described. During its development the reliability was the most important aspect because it is used in the computerized control of a 5 MW research reactor. DUAL-PROCESS is fully compatible with the earlier single processor control system PROCESS-24K. The paper deals in detail with the communication, synchronization, error detection and error recovery problems of the operating system. (author)

Advances in the manufacture of clad tubes and components for PHWR fuel bundle

International Nuclear Information System (INIS)

Saibaba, N.; Jha, S.K.; Chandrasekha, B.; Tonpe, S.; Jayaraj, R.N.

2010-01-01

Fuel bundles for Pressurized Heavy Water Reactors (PHWRs) consists of Uranium di-oxide pellets encapsulated into thin wall Zircaloy clad tubes. Other components such as end caps, bearing pads and spacer pads are the integral elements of the fuel bundle. As the fuel assembly is subjected to severe operating conditions of high temperature and pressure in addition to continual irradiation exposure, all the components are manufactured conforming to stringent specifications with respect to chemical composition, mechanical & metallurgical properties and dimensional tolerances. The integrity of each component is ensured by NDE at different stages of manufacture. The manufacturing route for fuel tubes and components comprise of a combination of thermomechanical processing and each process step has marked effect on the final properties. The fuel tubes are manufactured by processing the extruded blanks in four stage cold pilgering with intermediate annealing and final stress relieving operation. The bar material is produced by hot extrusion followed by multi-pass swaging and intermediate annealing. Spacer pads and bearing pads are manufactured by blanking and coining of Zircaloy sheet which is made by a combination of hot and cold rolling operations. Due to the small size and stringent dimensional requirements of these appendages, selection of production route and optimization of process parameters are important. This paper discusses about various measures taken for improving the recoveries and mechanical and corrosion properties of the tube, sheet and bar materials being manufactured at Nuclear Fuel Complex, Hyderabad For the production of clad tubes, modifications at extrusion stage to reduce the wall thickness variation, introduction of ultrasonic testing of extruded blanks, optimization of cold working and heat treatment parameters at various stages of production etc. were done. The finished bar material is subjected to 100% Ultrasonic and eddy current testing to ensure

Quasi-Birth-and-Death Processes with Rational Arrival Process Components

DEFF Research Database (Denmark)

Bean, Nigel G.; Nielsen, Bo Friis

2010-01-01

This paper introduces the concept of a Quasi-Birth-and-Death process (QBD) with Rational Arrival Process (RAP) components. We use the physical interpretation of the prediction process of the RAP, developed by Asmussen and Bladt, and develop an analysis that parallels the analysis of a traditional...... QBD. Further, we present an algorithm for the numerical evaluation of the matrix G. As an example, we consider two queues where the arrival process and the sequence of service times are taken from two dependent RAPs, that are not Markovian Arrival Processes......This paper introduces the concept of a Quasi-Birth-and-Death process (QBD) with Rational Arrival Process (RAP) components. We use the physical interpretation of the prediction process of the RAP, developed by Asmussen and Bladt, and develop an analysis that parallels the analysis of a traditional...

Stochastic processes

CERN Document Server

Parzen, Emanuel

1962-01-01

Well-written and accessible, this classic introduction to stochastic processes and related mathematics is appropriate for advanced undergraduate students of mathematics with a knowledge of calculus and continuous probability theory. The treatment offers examples of the wide variety of empirical phenomena for which stochastic processes provide mathematical models, and it develops the methods of probability model-building.Chapter 1 presents precise definitions of the notions of a random variable and a stochastic process and introduces the Wiener and Poisson processes. Subsequent chapters examine

Dosimetry and process control for radiation processing

International Nuclear Information System (INIS)

Mod Ali, N.

2002-01-01

Complete text of publication follows. Accurate radiation dosimetry can provide quality assurance in radiation processing. Considerable relevant experiences in dosimetry by the SSDL-MINT has necessitate the development of methods making measurement at gamma plant traceable to the national standard. It involves the establishment of proper calibration procedure and selection of appropriate transfer system/technique to assure adequate traceability to a primary radiation standard. The effort forms the basis for irradiation process control, the legal approval of the process by the public health authorities (medical product sterilization and food preservation) and the safety and acceptance of the product

Process mining using BPMN: relating event logs and process models

NARCIS (Netherlands)

Kalenkova, A.A.; van der Aalst, W.M.P.; Lomazova, I.A.; Rubin, V.A.

2017-01-01

Process-aware information systems (PAIS) are systems relying on processes, which involve human and software resources to achieve concrete goals. There is a need to develop approaches for modeling, analysis, improvement and monitoring processes within PAIS. These approaches include process mining

Process mining using BPMN : relating event logs and process models

NARCIS (Netherlands)

Kalenkova, A.A.; Aalst, van der W.M.P.; Lomazova, I.A.; Rubin, V.A.

2015-01-01

Process-aware information systems (PAIS) are systems relying on processes, which involve human and software resources to achieve concrete goals. There is a need to develop approaches for modeling, analysis, improvement and monitoring processes within PAIS. These approaches include process mining

Process modeling for Humanities: tracing and analyzing scientific processes

OpenAIRE

Hug , Charlotte; Salinesi , Camille; Deneckere , Rebecca; Lamasse , Stéphane

2011-01-01

International audience; This paper concerns epistemology and the understanding of research processes in Humanities, such as Archaeology. We believe that to properly understand research processes, it is essential to trace them. The collected traces depend on the process model established, which has to be as accurate as possible to exhaustively record the traces. In this paper, we briefly explain why the existing process models for Humanities are not sufficient to represent traces. We then pres...

Poisson processes

NARCIS (Netherlands)

Boxma, O.J.; Yechiali, U.; Ruggeri, F.; Kenett, R.S.; Faltin, F.W.

2007-01-01

The Poisson process is a stochastic counting process that arises naturally in a large variety of daily life situations. We present a few definitions of the Poisson process and discuss several properties as well as relations to some well-known probability distributions. We further briefly discuss the

Process improvement : the creation and evaluation of process alternatives

NARCIS (Netherlands)

Netjes, M.

2010-01-01

Companies continuously strive to improve their processes to increase productivity and delivered quality against lower costs. With Business Process Redesign (BPR) projects such improvement goals can be achieved. BPR involves the restructuring of business processes, stimulated by the application of

The permanental process

DEFF Research Database (Denmark)

McCullagh, Peter; Møller, Jesper

2006-01-01

We extend the boson process first to a large class of Cox processes and second to an even larger class of infinitely divisible point processes. Density and moment results are studied in detail. These results are obtained in closed form as weighted permanents, so the extension i called a permanental...... process. Temporal extensions and a particularly tractable case of the permanental process are also studied. Extensions of the fermion process along similar lines, leading to so-called determinantal processes, are discussed....

Dry process potentials

International Nuclear Information System (INIS)

Faugeras, P.

1997-01-01

Various dry processes have been studied and more or less developed in order particularly to reduce the waste quantities but none of them had replaced the PUREX process, for reasons departing to policy errors, un-appropriate demonstration examples or too late development, although realistic and efficient dry processes such as a fluoride selective volatility based processes have been demonstrated in France (CLOVIS, ATILA) and would be ten times cheaper than the PUREX process. Dry processes could regain interest in case of a nuclear revival (following global warming fears) or thermal wastes over-production. In the near future, dry processes could be introduced in complement to the PUREX process, especially at the end of the process cycle, for a more efficient recycling and safer storage (inactivation)

Business Process Customization using Process Merging Techniques

NARCIS (Netherlands)

Bulanov, Pavel; Lazovik, Alexander; Aiello, Marco

2012-01-01

One of the important application of service composition techniques lies in the field of business process management. Essentially a business process can be considered as a composition of services, which is usually prepared by domain experts, and many tasks still have to be performed manually. These

Fiber optic micro sensor for the measurement of tendon forces

Directory of Open Access Journals (Sweden)

Behrmann Gregory P

2012-10-01

Full Text Available Abstract A fiber optic sensor developed for the measurement of tendon forces was designed, numerically modeled, fabricated, and experimentally evaluated. The sensor incorporated fiber Bragg gratings and micro-fabricated stainless steel housings. A fiber Bragg grating is an optical device that is spectrally sensitive to axial strain. Stainless steel housings were designed to convert radial forces applied to the housing into axial forces that could be sensed by the fiber Bragg grating. The metal housings were fabricated by several methods including laser micromachining, swaging, and hydroforming. Designs are presented that allow for simultaneous temperature and force measurements as well as for simultaneous resolution of multi-axis forces. The sensor was experimentally evaluated by hydrostatic loading and in vitro testing. A commercial hydraulic burst tester was used to provide uniform pressures on the sensor in order to establish the linearity, repeatability, and accuracy characteristics of the sensor. The in vitro experiments were performed in excised tendon and in a dynamic gait simulator to simulate biological conditions. In both experimental conditions, the sensor was found to be a sensitive and reliable method for acquiring minimally invasive measurements of soft tissue forces. Our results suggest that this sensor will prove useful in a variety of biomechanical measurements.

Progress report, Chemistry and Materials Division: 1982 July 1 - September 30

International Nuclear Information System (INIS)

1982-10-01

During the third quarter of 1982, work in solid state studies included study of energy spectra of Auger electrons from a silicon single crystal, use of an excimer laser to anneal an aluminum crystal implanted with iron atoms, studies of defects created by helium ion irradiation of a dilute copper-indium alloy crystal, and computer simulations of ion channeling in a platinum crystal surface. Work in radiation chemistry on the enhancement of water calorimetry sensitivity continued. A surface science program to understand the temporal oscillations in the oxidation of carbon monoxide over platinum continued with the study of the interaction of oxygen with the (100) crystallographic face of platinum. Studies in analytical chemistry included a comparison of fuel burnup results using 145 Nd + 146 Nd and 148 Nd, and a preliminary investigation into methods of reduction of U(VI) to U(IV), particularly electrolytic reduction. Materials science work continued on the fracture surfaces of Exel alloys cracked in hydrogen gas, the true incubation time for stress corrosion cracking in cesium-cadmium vapour mixtures, evidence for a previously unknown hexagonal phase of germanium, growth experiments in the DIDO reactor on swaged single-crystals, and examination of the first zirconium specimen purified by electrotransport in the CRNL equipment

Fiber optic micro sensor for the measurement of tendon forces.

Science.gov (United States)

Behrmann, Gregory P; Hidler, Joseph; Mirotznik, Mark S

2012-10-03

A fiber optic sensor developed for the measurement of tendon forces was designed, numerically modeled, fabricated, and experimentally evaluated. The sensor incorporated fiber Bragg gratings and micro-fabricated stainless steel housings. A fiber Bragg grating is an optical device that is spectrally sensitive to axial strain. Stainless steel housings were designed to convert radial forces applied to the housing into axial forces that could be sensed by the fiber Bragg grating. The metal housings were fabricated by several methods including laser micromachining, swaging, and hydroforming. Designs are presented that allow for simultaneous temperature and force measurements as well as for simultaneous resolution of multi-axis forces.The sensor was experimentally evaluated by hydrostatic loading and in vitro testing. A commercial hydraulic burst tester was used to provide uniform pressures on the sensor in order to establish the linearity, repeatability, and accuracy characteristics of the sensor. The in vitro experiments were performed in excised tendon and in a dynamic gait simulator to simulate biological conditions. In both experimental conditions, the sensor was found to be a sensitive and reliable method for acquiring minimally invasive measurements of soft tissue forces. Our results suggest that this sensor will prove useful in a variety of biomechanical measurements.

Design, Fabrication and Performance of Boron-Carbide Control Elements

International Nuclear Information System (INIS)

Brammer, H.A.; Jacobson, J.

1964-01-01

A control blade design, incorporating boron-carbide (B 4 C) in stainless-steel tubes, was introduced into service in boiling water reactors in April 1961. Since that time this blade has become the standard reference control element in General Electric boiling-water reactors, replacing the 2% boron-stainless-steel blades previously used. The blades consist of a sheathed, cruciform array of small vertical stainless-steel tubes filled with compácted boron-carbide powder. The boron-carbide powder is confined longitudinally into several independent compartments by swaging over ball bearings located inside the tubes. The development and use of boron-carbide control rods is discussed in five phases: 1. Summary of experience with boron-steel blades and reasons for transition to boron-carbide control; 2. Design of the boron-carbide blade, beginning with developmental experiments, including early measurements performed in the AEC ''Control Rod Material and Development Program'' at the Vallecitos Atomic Laboratory, through a description of the final control blade configuration; 3. Fabrication of the blades and quality control procedures; 4. Results of confirmatory pre-operational mechanical and reactivity testing; and 5. Post-operational experience with the blades, including information on the results of mechanical inspection and reactivity testing after two years of reactor service. (author) [fr

Business process transformation the process tangram framework

CERN Document Server

Sharma, Chitra

2015-01-01

This book presents a framework through transformation and explains  how business goals can be translated into realistic plans that are tangible and yield real results in terms of the top line and the bottom line. Process Transformation is like a tangram puzzle, which has multiple solutions yet is essentially composed of seven 'tans' that hold it together. Based on practical experience and intensive research into existing material, 'Process Tangram' is a simple yet powerful framework that proposes Process Transformation as a program. The seven 'tans' are: the transformation program itself, triggers, goals, tools and techniques, culture, communication and success factors. With its segregation into tans and division into core elements, this framework makes it possible to use 'pick and choose' to quickly and easily map an organization's specific requirements. Change management and process modeling are covered in detail. In addition, the book approaches managed services as a model of service delivery, which it ex...

Composable Data Processing in Environmental Science - A Process View

NARCIS (Netherlands)

Wombacher, Andreas

Data processing in environmental science is essential for doing science. The heterogeneity of data sources, data processing operations and infrastructures results in a lot of manual data and process integration work done by each scientist individually. This is very inefficient and time consuming.

Processing module operating methods, processing modules, and communications systems

Science.gov (United States)

McCown, Steven Harvey; Derr, Kurt W.; Moore, Troy

2014-09-09

A processing module operating method includes using a processing module physically connected to a wireless communications device, requesting that the wireless communications device retrieve encrypted code from a web site and receiving the encrypted code from the wireless communications device. The wireless communications device is unable to decrypt the encrypted code. The method further includes using the processing module, decrypting the encrypted code, executing the decrypted code, and preventing the wireless communications device from accessing the decrypted code. Another processing module operating method includes using a processing module physically connected to a host device, executing an application within the processing module, allowing the application to exchange user interaction data communicated using a user interface of the host device with the host device, and allowing the application to use the host device as a communications device for exchanging information with a remote device distinct from the host device.

Improving the process of process modelling by the use of domain process patterns

NARCIS (Netherlands)

Koschmider, A.; Reijers, H.A.

2015-01-01

The use of business process models has become prevalent in a wide area of enterprise applications. But while their popularity is expanding, concerns are growing with respect to their proper creation and maintenance. An obvious way to boost the efficiency of creating high-quality business process

Trends in business process analysis: from verification to process mining

NARCIS (Netherlands)

Aalst, van der W.M.P.; Cardoso, J.; Cordeiro, J.; Filipe, J.

2007-01-01

Business process analysis ranges from model verification at design-time to the monitoring of processes at runtime. Much progress has been achieved in process verification. Today we are able to verify the entire reference model of SAP without any problems. Moreover, more and more processes leave

Automatic extraction of process categories from process model collections

NARCIS (Netherlands)

Malinova, M.; Dijkman, R.M.; Mendling, J.; Lohmann, N.; Song, M.; Wohed, P.

2014-01-01

Many organizations build up their business process management activities in an incremental way. As a result, there is no overarching structure defined at the beginning. However, as business process modeling initiatives often yield hundreds to thousands of process models, there is a growing need for

Opportunities and challenges for process control in process intensification

NARCIS (Netherlands)

Nikacevic, N.M.; Huesman, A.E.M.; Hof, Van den P.M.J.; Stankiewicz, A.

2012-01-01

This is a review and position article discussing the role and prospective for process control in process intensification. Firstly, the article outlines the classical role of control in process systems, presenting an overview of control systems’ development, from basic PID control to the advanced

Transforming spatial point processes into Poisson processes using random superposition

DEFF Research Database (Denmark)

Møller, Jesper; Berthelsen, Kasper Klitgaaard

with a complementary spatial point process Y  to obtain a Poisson process X∪Y  with intensity function β. Underlying this is a bivariate spatial birth-death process (Xt,Yt) which converges towards the distribution of (X,Y). We study the joint distribution of X and Y, and their marginal and conditional distributions....... In particular, we introduce a fast and easy simulation procedure for Y conditional on X. This may be used for model checking: given a model for the Papangelou intensity of the original spatial point process, this model is used to generate the complementary process, and the resulting superposition is a Poisson...... process with intensity function β if and only if the true Papangelou intensity is used. Whether the superposition is actually such a Poisson process can easily be examined using well known results and fast simulation procedures for Poisson processes. We illustrate this approach to model checking...

Process/Equipment Co-Simulation on Syngas Chemical Looping Process

Energy Technology Data Exchange (ETDEWEB)

Zeng, Liang; Zhou, Qiang; Fan, Liang-Shih

2012-09-30

The chemical looping strategy for fossil energy applications promises to achieve an efficient energy conversion system for electricity, liquid fuels, hydrogen and/or chemicals generation, while economically separate CO{sub 2} by looping reaction design in the process. Chemical looping particle performance, looping reactor engineering, and process design and applications are the key drivers to the success of chemical looping process development. In order to better understand and further scale up the chemical looping process, issues such as cost, time, measurement, safety, and other uncertainties need to be examined. To address these uncertainties, advanced reaction/reactor modeling and process simulation are highly desired and the modeling efforts can accelerate the chemical looping technology development, reduce the pilot-scale facility design time and operating campaigns, as well as reduce the cost and technical risks. The purpose of this work is thus to conduct multiscale modeling and simulations on the key aspects of chemical looping technology, including particle reaction kinetics, reactor design and operation, and process synthesis and optimization.

Process Fragment Libraries for Easier and Faster Development of Process-based Applications

Directory of Open Access Journals (Sweden)

David Schumm

2011-01-01

Full Text Available The term “process fragment” is recently gaining momentum in business process management research. We understand a process fragment as a connected and reusable process structure, which has relaxed completeness and consistency criteria compared to executable processes. We claim that process fragments allow for an easier and faster development of process-based applications. As evidence to this claim we present a process fragment concept and show a sample collection of concrete, real-world process fragments. We present advanced application scenarios for using such fragments in development of process-based applications. Process fragments are typically managed in a repository, forming a process fragment library. On top of a process fragment library from previous work, we discuss the potential impact of using process fragment libraries in cross-enterprise collaboration and application integration.

Rapid thermal processing and beyond applications in semiconductor processing

CERN Document Server

Lerch, W

2008-01-01

Heat-treatment and thermal annealing are very common processing steps which have been employed during semiconductor manufacturing right from the beginning of integrated circuit technology. In order to minimize undesired diffusion, and other thermal budget-dependent effects, the trend has been to reduce the annealing time sharply by switching from standard furnace batch-processing (involving several hours or even days), to rapid thermal processing involving soaking times of just a few seconds. This transition from thermal equilibrium, to highly non-equilibrium, processing was very challenging a

Fractional Processes and Fractional-Order Signal Processing Techniques and Applications

CERN Document Server

Sheng, Hu; Qiu, TianShuang

2012-01-01

Fractional processes are widely found in science, technology and engineering systems. In Fractional Processes and Fractional-order Signal Processing, some complex random signals, characterized by the presence of a heavy-tailed distribution or non-negligible dependence between distant observations (local and long memory), are introduced and examined from the ‘fractional’ perspective using simulation, fractional-order modeling and filtering and realization of fractional-order systems. These fractional-order signal processing (FOSP) techniques are based on fractional calculus, the fractional Fourier transform and fractional lower-order moments. Fractional Processes and Fractional-order Signal Processing: • presents fractional processes of fixed, variable and distributed order studied as the output of fractional-order differential systems; • introduces FOSP techniques and the fractional signals and fractional systems point of view; • details real-world-application examples of FOSP techniques to demonstr...

Clinical Processes - The Killer Application for Constraint-Based Process Interactions

DEFF Research Database (Denmark)

Jiménez-Ramírez, Andrés; Barba, Irene; Reichert, Manfred

2018-01-01

. The scenario is subject to complex temporal constraints and entails the need for coordinating the constraint-based interactions among the processes related to a patient treatment process. As demonstrated in this work, the selected real process scenario can be suitably modeled through a declarative approach....... examples. However, to the best of our knowledge, they have not been used to model complex, real-world scenarios that comprise constraints going beyond control-flow. In this paper, we propose the use of a declarative language for modeling a sophisticated healthcare process scenario from the real world......For more than a decade, the interest in aligning information systems in a process-oriented way has been increasing. To enable operational support for business processes, the latter are usually specified in an imperative way. The resulting process models, however, tend to be too rigid to meet...

Process innovation laboratory

DEFF Research Database (Denmark)

Møller, Charles

2007-01-01

to create a new methodology for developing and exploring process models and applications. The paper outlines the process innovation laboratory as a new approach to BPI. The process innovation laboratory is a comprehensive framework and a collaborative workspace for experimenting with process models....... The process innovation laboratory facilitates innovation by using an integrated action learning approach to process modelling in a controlled environment. The study is based on design science and the paper also discusses the implications to EIS research and practice......Most organizations today are required not only to operate effective business processes but also to allow for changing business conditions at an increasing rate. Today nearly every business relies on their enterprise information systems (EIS) for process integration and future generations of EIS...

Membrane processes

Science.gov (United States)

Staszak, Katarzyna

2017-11-01

The membrane processes have played important role in the industrial separation process. These technologies can be found in all industrial areas such as food, beverages, metallurgy, pulp and paper, textile, pharmaceutical, automotive, biotechnology and chemical industry, as well as in water treatment for domestic and industrial application. Although these processes are known since twentieth century, there are still many studies that focus on the testing of new membranes' materials and determining of conditions for optimal selectivity, i. e. the optimum transmembrane pressure (TMP) or permeate flux to minimize fouling. Moreover the researchers proposed some calculation methods to predict the membrane processes properties. In this article, the laboratory scale experiments of membrane separation techniques, as well their validation by calculation methods are presented. Because membrane is the "heart" of the process, experimental and computational methods for its characterization are also described.

PROPOSAL OF SPATIAL OPTIMIZATION OF PRODUCTION PROCESS IN PROCESS DESIGNER

Directory of Open Access Journals (Sweden)

Peter Malega

2015-03-01

Full Text Available This contribution is focused on optimizing the use of space in the production process using software Process Designer. The aim of this contribution is to suggest possible improvements to the existing layout of the selected production process. Production process was analysed in terms of inputs, outputs and course of actions. Nowadays there are many software solutions aimed at optimizing the use of space. One of these software products is the Process Designer, which belongs to the product line Tecnomatix. This software is primarily aimed at production planning. With Process Designer is possible to design the layout of production and subsequently to analyse the production or to change according to the current needs of the company.

Process automation

International Nuclear Information System (INIS)

Moser, D.R.

1986-01-01

Process automation technology has been pursued in the chemical processing industries and to a very limited extent in nuclear fuel reprocessing. Its effective use has been restricted in the past by the lack of diverse and reliable process instrumentation and the unavailability of sophisticated software designed for process control. The Integrated Equipment Test (IET) facility was developed by the Consolidated Fuel Reprocessing Program (CFRP) in part to demonstrate new concepts for control of advanced nuclear fuel reprocessing plants. A demonstration of fuel reprocessing equipment automation using advanced instrumentation and a modern, microprocessor-based control system is nearing completion in the facility. This facility provides for the synergistic testing of all chemical process features of a prototypical fuel reprocessing plant that can be attained with unirradiated uranium-bearing feed materials. The unique equipment and mission of the IET facility make it an ideal test bed for automation studies. This effort will provide for the demonstration of the plant automation concept and for the development of techniques for similar applications in a full-scale plant. A set of preliminary recommendations for implementing process automation has been compiled. Some of these concepts are not generally recognized or accepted. The automation work now under way in the IET facility should be useful to others in helping avoid costly mistakes because of the underutilization or misapplication of process automation. 6 figs

Process Analytical Technology (PAT): batch-to-batch reproducibility of fermentation processes by robust process operational design and control.

Science.gov (United States)

Gnoth, S; Jenzsch, M; Simutis, R; Lübbert, A

2007-10-31

The Process Analytical Technology (PAT) initiative of the FDA is a reaction on the increasing discrepancy between current possibilities in process supervision and control of pharmaceutical production processes and its current application in industrial manufacturing processes. With rigid approval practices based on standard operational procedures, adaptations of production reactors towards the state of the art were more or less inhibited for long years. Now PAT paves the way for continuous process and product improvements through improved process supervision based on knowledge-based data analysis, "Quality-by-Design"-concepts, and, finally, through feedback control. Examples of up-to-date implementations of this concept are presented. They are taken from one key group of processes in recombinant pharmaceutical protein manufacturing, the cultivations of genetically modified Escherichia coli bacteria.

Defense Waste Processing Facility Process Simulation Package Life Cycle

International Nuclear Information System (INIS)

Reuter, K.

1991-01-01

The Defense Waste Processing Facility (DWPF) will be used to immobilize high level liquid radioactive waste into safe, stable, and manageable solid form. The complexity and classification of the facility requires that a performance based operator training to satisfy Department of Energy orders and guidelines. A major portion of the training program will be the application and utilization of Process Simulation Packages to assist in training the Control Room Operators on the fluctionality of the process and the application of the Distribution Control System (DCS) in operating and managing the DWPF process. The packages are being developed by the DWPF Computer and Information Systems Simulation Group. This paper will describe the DWPF Process Simulation Package Life Cycle. The areas of package scope, development, validation, and configuration management will be reviewed and discussed in detail

Comparative process mining in education : an approach based on process cubes

NARCIS (Netherlands)

van der Aalst, W.M.P.; Guo, S.; Gorissen, P.J.B.; Ceravolo, P.; Accorsi, R.; Cudre-Mauroux, P.

2015-01-01

Process mining techniques enable the analysis of a wide variety of processes using event data. For example, event logs can be used to automatically learn a process model (e.g., a Petri net or BPMN model). Next to the automated discovery of the real underlying process, there are process mining

Process mining

DEFF Research Database (Denmark)

van der Aalst, W.M.P.; Rubin, V.; Verbeek, H.M.W.

2010-01-01

Process mining includes the automated discovery of processes from event logs. Based on observed events (e.g., activities being executed or messages being exchanged) a process model is constructed. One of the essential problems in process mining is that one cannot assume to have seen all possible...... behavior. At best, one has seen a representative subset. Therefore, classical synthesis techniques are not suitable as they aim at finding a model that is able to exactly reproduce the log. Existing process mining techniques try to avoid such “overfitting” by generalizing the model to allow for more...... support for it). None of the existing techniques enables the user to control the balance between “overfitting” and “underfitting”. To address this, we propose a two-step approach. First, using a configurable approach, a transition system is constructed. Then, using the “theory of regions”, the model...

Process monitoring

International Nuclear Information System (INIS)

Anon.

1981-01-01

Many of the measurements and observations made in a nuclear processing facility to monitor processes and product quality can also be used to monitor the location and movements of nuclear materials. In this session information is presented on how to use process monitoring data to enhance nuclear material control and accounting (MC and A). It will be seen that SNM losses can generally be detected with greater sensitivity and timeliness and point of loss localized more closely than by conventional MC and A systems if process monitoring data are applied. The purpose of this session is to enable the participants to: (1) identify process unit operations that could improve control units for monitoring SNM losses; (2) choose key measurement points and formulate a loss indicator for each control unit; and (3) describe how the sensitivities and timeliness of loss detection could be determined for each loss indicator

Metacognition in Creativity: Process Awareness Used to Facilitate the Creative Process

DEFF Research Database (Denmark)

Valgeirsdóttir, Dagný; Onarheim, Balder

2017-01-01

to ensure capture of all instances of process awareness. Through this iterative process it was revealed that process awareness was predominantly observed in creativity related tasks. Moreover three distinct facets to process awareness emerged; planning, monitoring and reflecting, which were employed...... respectively before, during and after initiating a process and/or a workshop. We conclude that process awareness is an important creativity skill, being a crucial mechanism to enhance all stages of the creative process. If a designer becomes able to plan, monitor and reflect on his or her own cognitive...... processes, as well as other team members, he or she will be able to understand what works and what does not for advancing the creative process. In turn, that enables the designer to become more strategic about which actions are appropriate and at what time they are most usefully deployed; making the use...

Development of functionally-oriented technological processes of electroerosive processing

Science.gov (United States)

Syanov, S. Yu

2018-03-01

The stages of the development of functionally oriented technological processes of electroerosive processing from the separation of the surfaces of parts and their service functions to the determination of the parameters of the process of electric erosion, which will provide not only the quality parameters of the surface layer, but also the required operational properties, are described.

Data processing

International Nuclear Information System (INIS)

Cousot, P.

1988-01-01

The 1988 progress report of the Data Processing laboratory (Polytechnic School, France), is presented. The laboratory research fields are: the semantics, the tests and the semantic analysis of the codes, the formal calculus, the software applications, the algorithms, the neuron networks and VLSI (Very Large Scale Integration). The investigations concerning the polynomial rings are performed by means of the standard basis approach. Among the research topics, the Pascal codes, the parallel processing, the combinatorial, statistical and asymptotic properties of the fundamental data processing tools, the signal processing and the pattern recognition. The published papers, the congress communications and the thesis are also included [fr

PROCESS VARIABILITY REDUCTION THROUGH STATISTICAL PROCESS CONTROL FOR QUALITY IMPROVEMENT

Directory of Open Access Journals (Sweden)

B.P. Mahesh

2010-09-01

Full Text Available Quality has become one of the most important customer decision factors in the selection among the competing product and services. Consequently, understanding and improving quality is a key factor leading to business success, growth and an enhanced competitive position. Hence quality improvement program should be an integral part of the overall business strategy. According to TQM, the effective way to improve the Quality of the product or service is to improve the process used to build the product. Hence, TQM focuses on process, rather than results as the results are driven by the processes. Many techniques are available for quality improvement. Statistical Process Control (SPC is one such TQM technique which is widely accepted for analyzing quality problems and improving the performance of the production process. This article illustrates the step by step procedure adopted at a soap manufacturing company to improve the Quality by reducing process variability using Statistical Process Control.

Emotional Processing, Interaction Process, and Outcome in Clarification-Oriented Psychotherapy for Personality Disorders: A Process-Outcome Analysis.

Science.gov (United States)

Kramer, Ueli; Pascual-Leone, Antonio; Rohde, Kristina B; Sachse, Rainer

2016-06-01

It is important to understand the change processes involved in psychotherapies for patients with personality disorders (PDs). One patient process that promises to be useful in relation to the outcome of psychotherapy is emotional processing. In the present process-outcome analysis, we examine this question by using a sequential model of emotional processing and by additionally taking into account a therapist's appropriate responsiveness to a patient's presentation in clarification-oriented psychotherapy (COP), a humanistic-experiential form of therapy. The present study involved 39 patients with a range of PDs undergoing COP. Session 25 was assessed as part of the working phase of each therapy by external raters in terms of emotional processing using the Classification of Affective-Meaning States (CAMS) and in terms of the overall quality of therapist-patient interaction using the Process-Content-Relationship Scale (BIBS). Treatment outcome was assessed pre- and post-therapy using the Global Severity Index (GSI) of the SCL-90-R and the BDI. Results indicate that the good outcome cases showed more self-compassion, more rejecting anger, and a higher quality of therapist-patient interaction compared to poorer outcome cases. For good outcome cases, emotional processing predicted 18% of symptom change at the end of treatment, which was not found for poor outcome cases. These results are discussed within the framework of an integrative understanding of emotional processing as an underlying mechanism of change in COP, and perhaps in other effective therapy approaches for PDs.

Process Materialization Using Templates and Rules to Design Flexible Process Models

Science.gov (United States)

Kumar, Akhil; Yao, Wen

The main idea in this paper is to show how flexible processes can be designed by combining generic process templates and business rules. We instantiate a process by applying rules to specific case data, and running a materialization algorithm. The customized process instance is then executed in an existing workflow engine. We present an architecture and also give an algorithm for process materialization. The rules are written in a logic-based language like Prolog. Our focus is on capturing deeper process knowledge and achieving a holistic approach to robust process design that encompasses control flow, resources and data, as well as makes it easier to accommodate changes to business policy.

Thin film processes

CERN Document Server

Vossen, John L

1978-01-01

Remarkable advances have been made in recent years in the science and technology of thin film processes for deposition and etching. It is the purpose of this book to bring together tutorial reviews of selected filmdeposition and etching processes from a process viewpoint. Emphasis is placed on the practical use of the processes to provide working guidelines for their implementation, a guide to the literature, and an overview of each process.

Partial processing

International Nuclear Information System (INIS)

1978-11-01

This discussion paper considers the possibility of applying to the recycle of plutonium in thermal reactors a particular method of partial processing based on the PUREX process but named CIVEX to emphasise the differences. The CIVEX process is based primarily on the retention of short-lived fission products. The paper suggests: (1) the recycle of fission products with uranium and plutonium in thermal reactor fuel would be technically feasible; (2) it would, however, take ten years or more to develop the CIVEX process to the point where it could be launched on a commercial scale; (3) since the majority of spent fuel to be reprocessed this century will have been in storage for ten years or more, the recycling of short-lived fission products with the U-Pu would not provide an effective means of making refabrication fuel ''inaccessible'' because the radioactivity associated with the fission products would have decayed. There would therefore be no advantage in partial processing

Assessment of Process Capability: the case of Soft Drinks Processing Unit

Science.gov (United States)

Sri Yogi, Kottala

2018-03-01

The process capability studies have significant impact in investigating process variation which is important in achieving product quality characteristics. Its indices are to measure the inherent variability of a process and thus to improve the process performance radically. The main objective of this paper is to understand capability of the process being produced within specification of the soft drinks processing unit, a premier brands being marketed in India. A few selected critical parameters in soft drinks processing: concentration of gas volume, concentration of brix, torque of crock has been considered for this study. Assessed some relevant statistical parameters: short term capability, long term capability as a process capability indices perspective. For assessment we have used real time data of soft drinks bottling company which is located in state of Chhattisgarh, India. As our research output suggested reasons for variations in the process which is validated using ANOVA and also predicted Taguchi cost function, assessed also predicted waste monetarily this shall be used by organization for improving process parameters. This research work has substantially benefitted the organization in understanding the various variations of selected critical parameters for achieving zero rejection.

Perturbed GUE Minor Process and Warren's Process with Drifts

Science.gov (United States)

Ferrari, Patrik L.; Frings, René

2014-01-01

We consider the minor process of (Hermitian) matrix diffusions with constant diagonal drifts. At any given time, this process is determinantal and we provide an explicit expression for its correlation kernel. This is a measure on the Gelfand-Tsetlin pattern that also appears in a generalization of Warren's process (Electron. J. Probab. 12:573-590, 2007), in which Brownian motions have level-dependent drifts. Finally, we show that this process arises in a diffusion scaling limit from an interacting particle system in the anisotropic KPZ class in 2+1 dimensions introduced in Borodin and Ferrari (Commun. Math. Phys., 2008). Our results generalize the known results for the zero drift situation.

Integrated stationary Ornstein-Uhlenbeck process, and double integral processes

Science.gov (United States)

Abundo, Mario; Pirozzi, Enrica

2018-03-01

We find a representation of the integral of the stationary Ornstein-Uhlenbeck (ISOU) process in terms of Brownian motion Bt; moreover, we show that, under certain conditions on the functions f and g , the double integral process (DIP) D(t) = ∫βt g(s) (∫αs f(u) dBu) ds can be thought as the integral of a suitable Gauss-Markov process. Some theoretical and application details are given, among them we provide a simulation formula based on that representation by which sample paths, probability densities and first passage times of the ISOU process are obtained; the first-passage times of the DIP are also studied.

Integrating textual and model-based process descriptions for comprehensive process search

NARCIS (Netherlands)

Leopold, Henrik; van der Aa, Han; Pittke, Fabian; Raffel, Manuel; Mendling, Jan; Reijers, Hajo A.

2016-01-01

Documenting business processes using process models is common practice in many organizations. However, not all process information is best captured in process models. Hence, many organizations complement these models with textual descriptions that specify additional details. The problem with this

Neurological evidence linguistic processes precede perceptual simulation in conceptual processing.

Science.gov (United States)

Louwerse, Max; Hutchinson, Sterling

2012-01-01

There is increasing evidence from response time experiments that language statistics and perceptual simulations both play a role in conceptual processing. In an EEG experiment we compared neural activity in cortical regions commonly associated with linguistic processing and visual perceptual processing to determine to what extent symbolic and embodied accounts of cognition applied. Participants were asked to determine the semantic relationship of word pairs (e.g., sky - ground) or to determine their iconic relationship (i.e., if the presentation of the pair matched their expected physical relationship). A linguistic bias was found toward the semantic judgment task and a perceptual bias was found toward the iconicity judgment task. More importantly, conceptual processing involved activation in brain regions associated with both linguistic and perceptual processes. When comparing the relative activation of linguistic cortical regions with perceptual cortical regions, the effect sizes for linguistic cortical regions were larger than those for the perceptual cortical regions early in a trial with the reverse being true later in a trial. These results map upon findings from other experimental literature and provide further evidence that processing of concept words relies both on language statistics and on perceptual simulations, whereby linguistic processes precede perceptual simulation processes.

Silicon integrated circuit process

International Nuclear Information System (INIS)

Lee, Jong Duck

1985-12-01

This book introduces the process of silicon integrated circuit. It is composed of seven parts, which are oxidation process, diffusion process, ion implantation process such as ion implantation equipment, damage, annealing and influence on manufacture of integrated circuit and device, chemical vapor deposition process like silicon Epitaxy LPCVD and PECVD, photolithography process, including a sensitizer, spin, harden bake, reflection of light and problems related process, infrared light bake, wet-etch, dry etch, special etch and problems of etching, metal process like metal process like metal-silicon connection, aluminum process, credibility of aluminum and test process.

Silicon integrated circuit process

Energy Technology Data Exchange (ETDEWEB)

Lee, Jong Duck

1985-12-15

This book introduces the process of silicon integrated circuit. It is composed of seven parts, which are oxidation process, diffusion process, ion implantation process such as ion implantation equipment, damage, annealing and influence on manufacture of integrated circuit and device, chemical vapor deposition process like silicon Epitaxy LPCVD and PECVD, photolithography process, including a sensitizer, spin, harden bake, reflection of light and problems related process, infrared light bake, wet-etch, dry etch, special etch and problems of etching, metal process like metal process like metal-silicon connection, aluminum process, credibility of aluminum and test process.

Industrial processing versus home processing of tomato sauce

NARCIS (Netherlands)

Tomas, Merve; Beekwilder, Jules; Hall, Robert D.; Sagdic, Osman; Boyacioglu, Dilek; Capanoglu, Esra

2017-01-01

The effect of industrial and home processing, in vitro gastrointestinal digestion, individual phenolic content, and antioxidant capacity of tomato into tomato sauce were investigated. Industrial processing of tomato fruit into sauce had an overall positive effect on the total antioxidant capacity

Genetic process mining

NARCIS (Netherlands)

Aalst, van der W.M.P.; Alves De Medeiros, A.K.; Weijters, A.J.M.M.; Ciardo, G.; Darondeau, P.

2005-01-01

The topic of process mining has attracted the attention of both researchers and tool vendors in the Business Process Management (BPM) space. The goal of process mining is to discover process models from event logs, i.e., events logged by some information system are used to extract information about

Marshaling and Acquiring Resources for the Process Improvement Process

Science.gov (United States)

1993-06-01

stakeholders. ( Geber , 1990) D. IDENTIFYING SUPPLIERS Suppliers are just as crucial to setting requirements for processes as are customers. Although...output ( Geber , 1990, p. 32). Before gathering resources for process improvement, the functional manager must ensure that the relationship of internal...him patent information and clerical people process his applications. ( Geber , 1990, pp. 29-34) To get the full benefit of a white-collar worker as a

Process for recovering uranium from wet process phosphoric acid (III)

International Nuclear Information System (INIS)

Pyrih, R.Z.; Rickard, R.S.; Carrington, O.F.

1983-01-01

Uranium is conventionally recovered from wet-process phosphoric acid by two liquid ion exchange steps using a mixture of mono- and disubstituted phenyl esters of orthophosphoric acid (OPPA). Efficiency of the process drops as the mono-OPPA is lost preferentially to the aqueous phase. This invention provides a process for the removal of the uranium process organics (OPPA and organic solvents) from the raffinate of the first liquid ion exchange step and their return to the circuit. The process organics are removed by a combination flotation and absorption step, which results in the recovery of the organics on beads of a hydrophobic styrene polymer

Extensible packet processing architecture

Science.gov (United States)

Robertson, Perry J.; Hamlet, Jason R.; Pierson, Lyndon G.; Olsberg, Ronald R.; Chun, Guy D.

2013-08-20

A technique for distributed packet processing includes sequentially passing packets associated with packet flows between a plurality of processing engines along a flow through data bus linking the plurality of processing engines in series. At least one packet within a given packet flow is marked by a given processing engine to signify by the given processing engine to the other processing engines that the given processing engine has claimed the given packet flow for processing. A processing function is applied to each of the packet flows within the processing engines and the processed packets are output on a time-shared, arbitered data bus coupled to the plurality of processing engines.

Process intensification on membrane-based process for blackcurrant juice concentration

DEFF Research Database (Denmark)

Fjerbæk Søtoft, Lene; Rong, Ben-Guang; Christensen, Knud Villy

Juice concentrate production is a field where process intensification and novel concentration processes need to be implemented. The paper presents a systematic approach for process synthesis based on membrane processes for the concentration of blackcurrant juice, exemplified by the aroma recovery...... using combinations of vacuum membrane distillation and traditional distillation. Furthermore, the paper further suggests a novel method for the combination of nanofiltration, reverse osmosis and membrane distillation for the concentration of the dearomatized juice....

Application of various technological processes in red clover seed processing

OpenAIRE

Đokić, Dragoslav; Stanisavljević, Rade; Terzić, Dragan; Marković, Jordan; Radivojević, Gordana; Anđelković, Bojan; Barać, Saša

2012-01-01

This paper presents the results of the processing of natural red clover seed on the processing equipment using different technological methods. Red clover seed, for the establishment and crop utilization, must be of high purity, germination, and high genetic values. These requirements are achieved by processing, or removing impurities and poor quality seeds. Red clover seed processing involves a number of operations, of which the most important are: cleaning, packaging, labeling and storage. ...

CO-PRODUCT ENHANCEMENT AND DEVELOPMENT FOR THE MASADA OXYNOL PROCESS PROCESS

Energy Technology Data Exchange (ETDEWEB)

Donald V. Watkins

2010-06-14

The focus of this project was an overall process improvement through the enhancement of the co-product streams. The enhancement of the process operations and co-products will increase both ethanol production and the value of other process outputs and reduces the amount of waste byproducts. This leads to a more economical and environmentally sound alternative to landfill disposal of municipal solid waste (MSW). These enhancements can greatly increase the commercial potential for the production of ethanol from MSW by the Masada CES OxyNol process. Both technological and economical issues were considered for steps throughout the conversion process. The research efforts of this project are varied but synergistic. The project investigated many of the operations involved in the Masada process with the overall goal of process improvements. The general goal of the testing was to improve co-product quality, improve conversions efficiencies, minimize process losses, increase energy efficiency, and mitigate process and commercialization risks. The project was divided into 16 subtasks as described in general terms below. All these tasks are interrelated but not necessarily interdependent.

Modeling the Object-Oriented Software Process: OPEN and the Unified Process

NARCIS (Netherlands)

van den Berg, Klaas; Aksit, Mehmet; van den Broek, P.M.

A short introduction to software process modeling is presented, particularly object-oriented modeling. Two major industrial process models are discussed: the OPEN model and the Unified Process model. In more detail, the quality assurance in the Unified Process tool (formally called Objectory) is

Links between attachment and social information processing: examination of intergenerational processes.

Science.gov (United States)

Dykas, Matthew J; Ehrlich, Katherine B; Cassidy, Jude

2011-01-01

This chapter describes theory and research on intergenerational connections between parents' attachment and children's social information processing, as well as between parents' social information processing and children's attachment. The chapter begins with a discussion of attachment theorists' early insights into the role that social information processing plays in attachment processes. Next, current theory about the mechanisms through which cross-generational links between attachment and social information processing might emerge is presented. The central proposition is that the quality of attachment and/or the social information processing of the parent contributes to the quality of attachment and/or social information processing in the child, and these links emerge through mediating processes related to social learning, open communication, gate-keeping, emotion regulation, and joint attention. A comprehensive review of the literature is then presented. The chapter ends with the presentation of a current theoretical perspective and suggestions for future empirical and clinical endeavors.

A Repeatable Collaboration Process for Exploring Business Process Improvement Alternatives

NARCIS (Netherlands)

Sol, H G; Amiyo, Mercy; Nabukenya, J.

2012-01-01

The dynamic nature of organisations has increased demand for business process agility leading to the adoption of continuous Business Process Improvement (BPI). Success of BPI projects calls for continuous process analysis and exploration of several improvement alternatives. These activities are

Processing approaches to cognition: the impetus from the levels-of-processing framework.

Science.gov (United States)

Roediger, Henry L; Gallo, David A; Geraci, Lisa

2002-01-01

Processing approaches to cognition have a long history, from act psychology to the present, but perhaps their greatest boost was given by the success and dominance of the levels-of-processing framework. We review the history of processing approaches, and explore the influence of the levels-of-processing approach, the procedural approach advocated by Paul Kolers, and the transfer-appropriate processing framework. Processing approaches emphasise the procedures of mind and the idea that memory storage can be usefully conceptualised as residing in the same neural units that originally processed information at the time of encoding. Processing approaches emphasise the unity and interrelatedness of cognitive processes and maintain that they can be dissected into separate faculties only by neglecting the richness of mental life. We end by pointing to future directions for processing approaches.

Editorial: "Business process intelligence : connecting data and processes"

NARCIS (Netherlands)

Aalst, van der W.M.P.; Zhao, J.L.; Wang, H.; Wang, Harry Jiannan

2015-01-01

This introduction to the special issue on Business Process Intelligence (BPI) discusses the relation between data and processes. The recent attention for Big Data illustrates that organizations are aware of the potential of the torrents of data generated by today's information systems. However, at

Modeling the Object-Oriented Software Process: OPEN and the Unified Process

OpenAIRE

van den Berg, Klaas; Aksit, Mehmet; van den Broek, P.M.

1999-01-01

A short introduction to software process modeling is presented, particularly object-oriented modeling. Two major industrial process models are discussed: the OPEN model and the Unified Process model. In more detail, the quality assurance in the Unified Process tool (formally called Objectory) is reviewed.

Process modelling on a canonical basis[Process modelling; Canonical modelling

Energy Technology Data Exchange (ETDEWEB)

Siepmann, Volker

2006-12-20

Based on an equation oriented solving strategy, this thesis investigates a new approach to process modelling. Homogeneous thermodynamic state functions represent consistent mathematical models of thermodynamic properties. Such state functions of solely extensive canonical state variables are the basis of this work, as they are natural objective functions in optimisation nodes to calculate thermodynamic equilibrium regarding phase-interaction and chemical reactions. Analytical state function derivatives are utilised within the solution process as well as interpreted as physical properties. By this approach, only a limited range of imaginable process constraints are considered, namely linear balance equations of state variables. A second-order update of source contributions to these balance equations is obtained by an additional constitutive equation system. These equations are general dependent on state variables and first-order sensitivities, and cover therefore practically all potential process constraints. Symbolic computation technology efficiently provides sparsity and derivative information of active equations to avoid performance problems regarding robustness and computational effort. A benefit of detaching the constitutive equation system is that the structure of the main equation system remains unaffected by these constraints, and a priori information allows to implement an efficient solving strategy and a concise error diagnosis. A tailor-made linear algebra library handles the sparse recursive block structures efficiently. The optimisation principle for single modules of thermodynamic equilibrium is extended to host entire process models. State variables of different modules interact through balance equations, representing material flows from one module to the other. To account for reusability and encapsulation of process module details, modular process modelling is supported by a recursive module structure. The second-order solving algorithm makes it

Uranium enrichment. Enrichment processes

International Nuclear Information System (INIS)

Alexandre, M.; Quaegebeur, J.P.

2009-01-01

Despite the remarkable progresses made in the diversity and the efficiency of the different uranium enrichment processes, only two industrial processes remain today which satisfy all of enriched uranium needs: the gaseous diffusion and the centrifugation. This article describes both processes and some others still at the demonstration or at the laboratory stage of development: 1 - general considerations; 2 - gaseous diffusion: physical principles, implementation, utilisation in the world; 3 - centrifugation: principles, elementary separation factor, flows inside a centrifuge, modeling of separation efficiencies, mechanical design, types of industrial centrifuges, realisation of cascades, main characteristics of the centrifugation process; 4 - aerodynamic processes: vortex process, nozzle process; 5 - chemical exchange separation processes: Japanese ASAHI process, French CHEMEX process; 6 - laser-based processes: SILVA process, SILMO process; 7 - electromagnetic and ionic processes: mass spectrometer and calutron, ion cyclotron resonance, rotating plasmas; 8 - thermal diffusion; 9 - conclusion. (J.S.)

Science-based information processing in the process control of power stations

International Nuclear Information System (INIS)

Weisang, C.

1992-01-01

Through the application of specialized systems, future-orientated information processing integrates the sciences of processes, control systems, process control strategies, user behaviour and ergonomics. Improvements in process control can be attained, inter alia, by the preparation of the information contained (e.g. by suppressing the flow of signals and replacing it with signals which are found on substance) and also by an ergonomic representation of the study of the process. (orig.) [de

Process mining: discovering direct successors in process logs

NARCIS (Netherlands)

Maruster, L.; Weijters, A.J.M.M.; Aalst, van der W.M.P.; Bosch, van den A.P.J.; Lange, S.; Satoh, K.; Smith, C.H.

2002-01-01

Workflow management technology requires the existence of explicit process models, i.e. a completely specified workflow design needs to be developed in order to enact a given workflow process. Such a workflow design is time consuming and often subjective and incomplete. We propose a learning method

Internal process: what is abstraction and distortion process?

Science.gov (United States)

Fiantika, F. R.; Budayasa, I. K.; Lukito, A.

2018-03-01

Geometry is one of the branch of mathematics that plays a major role in the development of science and technology. Thus, knowing the geometry concept is needed for students from their early basic level of thinking. A preliminary study showed that the elementary students have difficulty in perceiving parallelogram shape in a 2-dimention of a cube drawing as a square shape. This difficulty makes the students can not solve geometrical problems correctly. This problem is related to the internal thinking process in geometry. We conducted the exploration of students’ internal thinking processes in geometry particularly in distinguishing the square and parallelogram shape. How the students process their internal thinking through distortion and abstraction is the main aim of this study. Analysis of the geometrical test and deep interview are used in this study to obtain the data. The result of this study is there are two types of distortion and abstraction respectively in which the student used in their internal thinking processes.

Nonaqueous processing methods

International Nuclear Information System (INIS)

Coops, M.S.; Bowersox, D.F.

1984-09-01

A high-temperature process utilizing molten salt extraction from molten metal alloys has been developed for purification of spent power reactor fuels. Experiments with laboratory-scale processing operations show that purification and throughput parameters comparable to the Barnwell Purex process can be achieved by pyrochemical processing in equipment one-tenth the size, with all wastes being discharged as stable metal alloys at greatly reduced volume and disposal cost. This basic technology can be developed for large-scale processing of spent reactor fuels. 13 references, 4 figures

Transforming Collaborative Process Models into Interface Process Models by Applying an MDA Approach

Science.gov (United States)

Lazarte, Ivanna M.; Chiotti, Omar; Villarreal, Pablo D.

Collaborative business models among enterprises require defining collaborative business processes. Enterprises implement B2B collaborations to execute these processes. In B2B collaborations the integration and interoperability of processes and systems of the enterprises are required to support the execution of collaborative processes. From a collaborative process model, which describes the global view of the enterprise interactions, each enterprise must define the interface process that represents the role it performs in the collaborative process in order to implement the process in a Business Process Management System. Hence, in this work we propose a method for the automatic generation of the interface process model of each enterprise from a collaborative process model. This method is based on a Model-Driven Architecture to transform collaborative process models into interface process models. By applying this method, interface processes are guaranteed to be interoperable and defined according to a collaborative process.

Z-buffer image assembly processing in high parallel visualization processing

International Nuclear Information System (INIS)

Kaneko, Isamu; Muramatsu, Kazuhiro

2000-03-01

On the platform of the parallel computer with many processors, the domain decomposition method is used as a popular means of parallel processing. In these days when the simulation scale becomes much larger and takes a lot of time, the simultaneous visualization processing with the actual computation is much more needed, and especially in case of a real-time visualization, the domain decomposition technique is indispensable. In case of parallel rendering processing, the rendered results must be gathered to one processor to compose the integrated picture in the last stage. This integration is usually conducted by the method using Z-buffer values. This process, however, induces the crucial problems of much lower speed processing and local memory shortage in case of parallel processing exceeding more than several tens of processors. In this report, the two new solutions are proposed. The one is the adoption of a special operator (Reduce operator) in the parallelization process, and the other is a buffer compression by deleting the background informations. This report includes the performance results of these new techniques to investigate their effect with use of the parallel computer Paragon. (author)

Explosive processes in nucleosynthesis

International Nuclear Information System (INIS)

Boyd, R.N.

2002-01-01

There are many explosive processes in nucleosynthesis: big bang nucleosynthesis, the rp-process, the γ-process, the ν-process, and the r-process. However, I will discuss just the rp-process and the r-process in detail, primarily because both seem to have been very active research areas of late, and because they have great potential for studies with radioactive nuclear beams. I will also discuss briefly the γ-process because of its inevitability in conjunction with the rp-process. (orig.)

Processing Depth, Elaboration of Encoding, Memory Stores, and Expended Processing Capacity.

Science.gov (United States)

Eysenck, Michael W.; Eysenck, M. Christine

1979-01-01

The effects of several factors on expended processing capacity were measured. Expended processing capacity was greater when information was retrieved from secondary memory than from primary memory, when processing was of a deep, semantic nature than when it was shallow and physical, and when processing was more elaborate. (Author/GDC)

Sewer Processes

DEFF Research Database (Denmark)

Hvitved-Jacobsen, Thorkild; Vollertsen, Jes; Nielsen, Asbjørn Haaning

Since the first edition was published over a decade ago, advancements have been made in the design, operation, and maintenance of sewer systems, and new problems have emerged. For example, sewer processes are now integrated in computer models, and simultaneously, odor and corrosion problems caused...... by hydrogen sulfide and other volatile organic compounds, as well as other potential health issues, have caused environmental concerns to rise. Reflecting the most current developments, Sewer Processes: Microbial and Chemical Process Engineering of Sewer Networks, Second Edition, offers the reader updated...... and valuable information on the sewer as a chemical and biological reactor. It focuses on how to predict critical impacts and control adverse effects. It also provides an integrated description of sewer processes in modeling terms. This second edition is full of illustrative examples and figures, includes...

AN OVERVIEW OF PHARMACEUTICAL PROCESS VALIDATION AND PROCESS CONTROL VARIABLES OF TABLETS MANUFACTURING PROCESSES IN INDUSTRY

OpenAIRE

Mahesh B. Wazade*, Sheelpriya R. Walde and Abhay M. Ittadwar

2012-01-01

Validation is an integral part of quality assurance; the product quality is derived from careful attention to a number of factors including selection of quality parts and materials, adequate product and manufacturing process design, control of the process variables, in-process and end-product testing. Recently validation has become one of the pharmaceutical industry’s most recognized and discussed subjects. It is a critical success factor in product approval and ongoing commercialization, fac...

Phenomena based Methodology for Process Synthesis incorporating Process Intensification

DEFF Research Database (Denmark)

Lutze, Philip; Babi, Deenesh Kavi; Woodley, John

2013-01-01

at processes at the lowest level of aggregation which is the phenomena level. In this paper, a phenomena based synthesis/design methodology incorporating process intensification is presented. Using this methodology, a systematic identification of necessary and desirable (integrated) phenomena as well......Process intensification (PI) has the potential to improve existing as well as conceptual processes, in order to achieve a more sustainable production. PI can be achieved at different levels. That is, the unit operations, functional and/or phenomena level. The highest impact is expected by looking...... as generation and screening of phenomena based flowsheet options are presented using a decomposition based solution approach. The developed methodology as well as necessary tools and supporting methods are highlighted through a case study involving the production of isopropyl-acetate....

Minimal and careful processing

OpenAIRE

Nielsen, Thorkild

2004-01-01

In several standards, guidelines and publications, organic food processing is strongly associated with "minimal processing" and "careful processing". The term "minimal processing" is nowadays often used in the general food processing industry and described in literature. The term "careful processing" is used more specifically within organic food processing but is not yet clearly defined. The concept of carefulness seems to fit very well with the processing of organic foods, especially if it i...

The Newest Laser Processing

International Nuclear Information System (INIS)

Lee, Baek Yeon

2007-01-01

This book mentions laser processing with laser principle, laser history, laser beam property, laser kinds, foundation of laser processing such as laser oscillation, characteristic of laser processing, laser for processing and its characteristic, processing of laser hole including conception of processing of laser hole and each material, and hole processing of metal material, cut of laser, reality of cut, laser welding, laser surface hardening, application case of special processing and safety measurement of laser.

Process Integration Analysis of an Industrial Hydrogen Production Process

OpenAIRE

Stolten, Detlef; Grube, Thomas; Tock, Laurence; Maréchal, François; Metzger, Christian; Arpentinier, Philippe

2010-01-01

The energy efficiency of an industrial hydrogen production process using steam methane reforming (SMR) combined with the water gas shift reaction (WGS) is analyzed using process integration techniques based on heat cascade calculation and pinch analysis with the aim of identifying potential measures to enhance the process performance. The challenge is to satisfy the high temperature heat demand of the SMR reaction by minimizing the consumption of natural gas to feed the combustion and to expl...

Developing engineering processes through integrated modelling of product and process

DEFF Research Database (Denmark)

Nielsen, Jeppe Bjerrum; Hvam, Lars

2012-01-01

This article aims at developing an operational tool for integrated modelling of product assortments and engineering processes in companies making customer specific products. Integrating a product model in the design of engineering processes will provide a deeper understanding of the engineering...... activities as well as insight into how product features affect the engineering processes. The article suggests possible ways of integrating models of products with models of engineering processes. The models have been tested and further developed in an action research study carried out in collaboration...... with a major international engineering company....

Process-based costing.

Science.gov (United States)

Lee, Robert H; Bott, Marjorie J; Forbes, Sarah; Redford, Linda; Swagerty, Daniel L; Taunton, Roma Lee

2003-01-01

Understanding how quality improvement affects costs is important. Unfortunately, low-cost, reliable ways of measuring direct costs are scarce. This article builds on the principles of process improvement to develop a costing strategy that meets both criteria. Process-based costing has 4 steps: developing a flowchart, estimating resource use, valuing resources, and calculating direct costs. To illustrate the technique, this article uses it to cost the care planning process in 3 long-term care facilities. We conclude that process-based costing is easy to implement; generates reliable, valid data; and allows nursing managers to assess the costs of new or modified processes.

Colloid process engineering

CERN Document Server

Peukert, Wolfgang; Rehage, Heinz; Schuchmann, Heike

2015-01-01

This book deals with colloidal systems in technical processes and the influence of colloidal systems by technical processes. It explores how new measurement capabilities can offer the potential for a dynamic development of scientific and engineering, and examines the origin of colloidal systems and its use for new products. The future challenges to colloidal process engineering are the development of appropriate equipment and processes for the production and obtainment of multi-phase structures and energetic interactions in market-relevant quantities. The book explores the relevant processes and for controlled production and how they can be used across all scales.

Laser Processing of Multilayered Thermal Spray Coatings: Optimal Processing Parameters

Science.gov (United States)

Tewolde, Mahder; Zhang, Tao; Lee, Hwasoo; Sampath, Sanjay; Hwang, David; Longtin, Jon

2017-12-01

Laser processing offers an innovative approach for the fabrication and transformation of a wide range of materials. As a rapid, non-contact, and precision material removal technology, lasers are natural tools to process thermal spray coatings. Recently, a thermoelectric generator (TEG) was fabricated using thermal spray and laser processing. The TEG device represents a multilayer, multimaterial functional thermal spray structure, with laser processing serving an essential role in its fabrication. Several unique challenges are presented when processing such multilayer coatings, and the focus of this work is on the selection of laser processing parameters for optimal feature quality and device performance. A parametric study is carried out using three short-pulse lasers, where laser power, repetition rate and processing speed are varied to determine the laser parameters that result in high-quality features. The resulting laser patterns are characterized using optical and scanning electron microscopy, energy-dispersive x-ray spectroscopy, and electrical isolation tests between patterned regions. The underlying laser interaction and material removal mechanisms that affect the feature quality are discussed. Feature quality was found to improve both by using a multiscanning approach and an optional assist gas of air or nitrogen. Electrically isolated regions were also patterned in a cylindrical test specimen.

Application of statistical process control and process capability analysis procedures in orbiter processing activities at the Kennedy Space Center

Science.gov (United States)

Safford, Robert R.; Jackson, Andrew E.; Swart, William W.; Barth, Timothy S.

1994-01-01

Successful ground processing at KSC requires that flight hardware and ground support equipment conform to specifications at tens of thousands of checkpoints. Knowledge of conformance is an essential requirement for launch. That knowledge of conformance at every requisite point does not, however, enable identification of past problems with equipment, or potential problem areas. This paper describes how the introduction of Statistical Process Control and Process Capability Analysis identification procedures into existing shuttle processing procedures can enable identification of potential problem areas and candidates for improvements to increase processing performance measures. Results of a case study describing application of the analysis procedures to Thermal Protection System processing are used to illustrate the benefits of the approaches described in the paper.

Westinghouse modular grinding process - improvement for follow on processes

Energy Technology Data Exchange (ETDEWEB)

Fehrmann, Henning [Westinghouse Germany GmbH, Mannheim, State (Germany)

2013-07-01

In nuclear power plants (NPP) ion exchange (IX) resins are used in several systems for water treatment. The resins can be in bead or powdered form. For waste treatment of spent IX resins, two methods are basically used: Direct immobilization (e.g. with cement, bitumen, polymer or High Integrity Container (HIC)); Thermal treatment (e.g. drying, oxidation or pyrolysis). Bead resins have some properties (e.g. particle size and density) that can have negative impacts on following waste treatment processes. Negative impacts could be: Floatation of bead resins in cementation process; Sedimentation in pipeline during transportation; Poor compaction properties for Hot Resin Supercompaction (HRSC). Reducing the particle size of the bead resins can have beneficial effects enhancing further treatment processes and overcoming prior mentioned effects. Westinghouse Electric Company has developed a modular grinding process to crush/grind the bead resins. This modular process is designed for flexible use and enables a selective adjustment of particle size to tailor the grinding system to the customer needs. The system can be equipped with a crusher integrated in the process tank and if necessary a colloid mill. The crusher reduces the bead resins particle size and converts the bead resins to a pump able suspension with lower sedimentation properties. With the colloid mill the resins can be ground to a powder. Compared to existing grinding systems this equipment is designed to minimize radiation exposure of the worker during operation and maintenance. Using the crushed and/or ground bead resins has several beneficial effects like facilitating cementation process and recipe development, enhancing oxidation of resins, improving the Hot Resin Supercompaction volume reduction performance. (authors)

Westinghouse modular grinding process - improvement for follow on processes

International Nuclear Information System (INIS)

Fehrmann, Henning

2013-01-01

In nuclear power plants (NPP) ion exchange (IX) resins are used in several systems for water treatment. The resins can be in bead or powdered form. For waste treatment of spent IX resins, two methods are basically used: Direct immobilization (e.g. with cement, bitumen, polymer or High Integrity Container (HIC)); Thermal treatment (e.g. drying, oxidation or pyrolysis). Bead resins have some properties (e.g. particle size and density) that can have negative impacts on following waste treatment processes. Negative impacts could be: Floatation of bead resins in cementation process; Sedimentation in pipeline during transportation; Poor compaction properties for Hot Resin Supercompaction (HRSC). Reducing the particle size of the bead resins can have beneficial effects enhancing further treatment processes and overcoming prior mentioned effects. Westinghouse Electric Company has developed a modular grinding process to crush/grind the bead resins. This modular process is designed for flexible use and enables a selective adjustment of particle size to tailor the grinding system to the customer needs. The system can be equipped with a crusher integrated in the process tank and if necessary a colloid mill. The crusher reduces the bead resins particle size and converts the bead resins to a pump able suspension with lower sedimentation properties. With the colloid mill the resins can be ground to a powder. Compared to existing grinding systems this equipment is designed to minimize radiation exposure of the worker during operation and maintenance. Using the crushed and/or ground bead resins has several beneficial effects like facilitating cementation process and recipe development, enhancing oxidation of resins, improving the Hot Resin Supercompaction volume reduction performance. (authors)

Defense waste processing facility precipitate hydrolysis process

International Nuclear Information System (INIS)

Doherty, J.P.; Eibling, R.E.; Marek, J.C.

1986-03-01

Sodium tetraphenylborate and sodium titanate are used to assist in the concentration of soluble radionuclide in the Savannah River Plant's high-level waste. In the Defense Waste Processing Facility, concentrated tetraphenylborate/sodium titanate slurry containing cesium-137, strontium-90 and traces of plutonium from the waste tank farm is hydrolyzed in the Salt Processing Cell forming organic and aqueous phases. The two phases are then separated and the organic phase is decontaminated for incineration outside the DWPF building. The aqueous phase, containing the radionuclides and less than 10% of the original organic, is blended with the insoluble radionuclides in the high-level waste sludge and is fed to the glass melter for vitrification into borosilicate glass. During the Savannah River Laboratory's development of this process, copper (II) was found to act as a catalyst during the hydrolysis reactions, which improved the organic removal and simplified the design of the reactor

On some applications of diffusion processes for image processing

International Nuclear Information System (INIS)

Morfu, S.

2009-01-01

We propose a new algorithm inspired by the properties of diffusion processes for image filtering. We show that purely nonlinear diffusion processes ruled by Fisher equation allows contrast enhancement and noise filtering, but involves a blurry image. By contrast, anisotropic diffusion, described by Perona and Malik algorithm, allows noise filtering and preserves the edges. We show that combining the properties of anisotropic diffusion with those of nonlinear diffusion provides a better processing tool which enables noise filtering, contrast enhancement and edge preserving.

Grind hardening process

CERN Document Server

Salonitis, Konstantinos

2015-01-01

This book presents the grind-hardening process and the main studies published since it was introduced in 1990s.  The modelling of the various aspects of the process, such as the process forces, temperature profile developed, hardness profiles, residual stresses etc. are described in detail. The book is of interest to the research community working with mathematical modeling and optimization of manufacturing processes.

Transuranium processing plant

International Nuclear Information System (INIS)

King, L.J.

1983-01-01

The Transuranium Processing Plant (TRU) is a remotely operated, hot-cell, chemical processing facility of advanced design. The heart of TRU is a battery of nine heavily shielded process cells housed in a two-story building. Each cell, with its 54-inch-thick walls of a special high-density concrete, has enough shielding to stop the neutrons and gamma radiation from 1 gram of 252/sub Cf/ and associated fission products. Four cells contain chemical processing equipment, three contain equipment for the preparation and inspection of HFIR targets, and two cells are used for analytical chemistry operations. In addition, there are eight laboratories used for process development, for part of the process-control analyses, and for product finishing operations. Although the Transuranium Processing Plant was built for the purpose of recovering transuranium elements from targets irradiated in the High Flux Isotope Reactor (HFIR), it is also a highly versatile facility which has extensive provisions for changing and modifying equipment. Thus, it was a relatively simple matter to install a Solvent Extraction Test Facility (SETF) in one of the TRU chemical processing cells for use in the evaluation and demonstration of solvent extraction flowsheets for the recovery of fissile and fertile materials from irradiated reactor fuels. The equipment in the SETF has been designed for process development and demonstrations and the particular type of mixer-settler contactors was chosen because it is easy to observe and sample

Welding processes handbook

CERN Document Server

Weman, Klas

2003-01-01

Deals with the main commercially significant and commonly used welding processes. This title takes the student or novice welder through the individual steps involved in each process in an easily understood way. It covers many of the requirements referred to in European Standards including EN719, EN 729, EN 729 and EN 287.$bWelding processes handbook is a concise, explanatory guide to the main commercially significant and commonly-used welding processes. It takes the novice welder or student through the individual steps involved in each process in a clear and easily understood way. It is intended to provide an up-to-date reference to the major applications of welding as they are used in industry. The contents have been arranged so that it can be used as a textbook for European welding courses in accordance with guidelines from the European Welding Federation. Welding processes and equipment necessary for each process are described so that they can be applied to all instruction levels required by the EWF and th...

Kidney transplantation process in Brazil represented in business process modeling notation.

Science.gov (United States)

Peres Penteado, A; Molina Cohrs, F; Diniz Hummel, A; Erbs, J; Maciel, R F; Feijó Ortolani, C L; de Aguiar Roza, B; Torres Pisa, I

2015-05-01

Kidney transplantation is considered to be the best treatment for people with chronic kidney failure, because it improves the patients' quality of life and increases their length of survival compared with patients undergoing dialysis. The kidney transplantation process in Brazil is defined through laws, decrees, ordinances, and resolutions, but there is no visual representation of this process. The aim of this study was to analyze official documents to construct a representation of the kidney transplantation process in Brazil with the use of business process modeling notation (BPMN). The methodology for this study was based on an exploratory observational study, document analysis, and construction of process diagrams with the use of BPMN. Two rounds of validations by specialists were conducted. The result includes the kidney transplantation process in Brazil representation with the use of BPMN. We analyzed 2 digital documents that resulted in 2 processes with 45 total of activities and events, 6 organizations involved, and 6 different stages of the process. The constructed representation makes it easier to understand the rules for the business of kidney transplantation and can be used by the health care professionals involved in the various activities within this process. Construction of a representation with language appropriate for the Brazilian lay public is underway. Copyright © 2015 Elsevier Inc. All rights reserved.

High temperature nuclear process heat systems for chemical processes

International Nuclear Information System (INIS)

Jiacoletti, R.J.

1976-01-01

The development planning and status of the very high temperature gas cooled reactor as a source of industrial process heat is presented. The dwindling domestic reserves of petroleum and natural gas dictate major increases in the utilization of coal and nuclear sources to meet the national energy demand. The nuclear process heat system offers a unique combination of the two that is environmentally and economically attractive and technically sound. Conceptual studies of several energy-intensive processes coupled to a nuclear heat source are presented

Process development

International Nuclear Information System (INIS)

Zapata G, G.

1989-01-01

Process development: The paper describes the organization and laboratory facilities of the group working on radioactive ore processing studies. Contains a review of the carried research and the plans for the next future. A list of the published reports is also presented

Information Technology Process Improvement Decision-Making: An Exploratory Study from the Perspective of Process Owners and Process Managers

Science.gov (United States)

Lamp, Sandra A.

2012-01-01

There is information available in the literature that discusses information technology (IT) governance and investment decision making from an executive-level perception, yet there is little information available that offers the perspective of process owners and process managers pertaining to their role in IT process improvement and investment…

Process synthesis, design and analysis using a process-group contribution method

DEFF Research Database (Denmark)

Kumar Tula, Anjan; Eden, Mario R.; Gani, Rafiqul

2015-01-01

) techniques. The fundamental pillars of this framework are the definition and use of functional process-groups (building blocks) representing a wide range of process operations, flowsheet connectivity rules to join the process-groups to generate all the feasible flowsheet alternatives and flowsheet property...... models like energy consumption, atom efficiency, environmental impact to evaluate the performance of the generated alternatives. In this way, a list of feasible flowsheets are quickly generated, screened and selected for further analysis. Since the flowsheet is synthesized and the operations......This paper describes the development and application of a process-group contribution method to model, simulate and synthesize chemical processes. Process flowsheets are generated in the same way as atoms or groups of atoms are combined to form molecules in computer aided molecular design (CAMD...

Development of interface technology between unit processes in E-Refining process

Energy Technology Data Exchange (ETDEWEB)

Lee, S. H.; Lee, H. S.; Kim, J. G. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2010-10-15

The pyroprocessing is composed mainly four subprocesses, such as an electrolytic reduction, an electrorefining, an electrowinning, and waste salt regeneration/ solidification processes. The electrorefining process, one of main processes which are composed of pyroprocess to recover the useful elements from spent fuel, is under development by Korea Atomic Energy Research Institute as a sub process of pyrochemical treatment of spent PWR fuel. The CERS(Continuous ElectroRefining System) is composed of some unit processes such as an electrorefiner, a salt distiller, a melting furnace for the U-ingot and U-chlorinator (UCl{sub 3} making equipment) as shown in Fig. 1. In this study, the interfaces technology between unit processes in E-Refining system is investigated and developed for the establishment of integrated E-Refining operation system as a part of integrated pyroprocessing

A secondary fuel removal process: plasma processing

Energy Technology Data Exchange (ETDEWEB)

Min, J Y; Kim, Y S [Hanyang Univ., Seoul (Korea, Republic of); Bae, K K; Yang, M S [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1997-07-01

Plasma etching process of UO{sub 2} by using fluorine containing gas plasma is studied as a secondary fuel removal process for DUPIC (Direct Use of PWR spent fuel Into Candu) process which is taken into consideration for potential future fuel cycle in Korea. CF{sub 4}/O{sub 2} gas mixture is chosen for reactant gas and the etching rates of UO{sub 2} by the gas plasma are investigated as functions of CF{sub 4}/O{sub 2} ratio, plasma power, substrate temperature, and plasma gas pressure. It is found that the optimum CF{sub 4}/O{sub 2} ratio is around 4:1 at all temperatures up to 400 deg C and the etching rate increases with increasing r.f. power and substrate temperature. Under 150W r.f. power the etching rate reaches 1100 monolayers/min at 400 deg C, which is equivalent to about 0.5mm/min. (author).

Clinical Process Intelligence

DEFF Research Database (Denmark)

Vilstrup Pedersen, Klaus

2006-01-01

.e. local guidelines. From a knowledge management point of view, this externalization of generalized processes, gives the opportunity to learn from, evaluate and optimize the processes. "Clinical Process Intelligence" (CPI), will denote the goal of getting generalized insight into patient centered health...

Sustainable processing

DEFF Research Database (Denmark)

Kristensen, Niels Heine

2004-01-01

Kristensen_NH and_Beck A: Sustainable processing. In Otto Schmid, Alexander Beck and Ursula Kretzschmar (Editors) (2004): Underlying Principles in Organic and "Low-Input Food" Processing - Literature Survey. Research Institute of Organic Agriculture FiBL, CH-5070 Frick, Switzerland. ISBN 3-906081-58-3...

Food processing

NARCIS (Netherlands)

Teodorowicz, Malgorzata; Neerven, Van Joost; Savelkoul, Huub

2017-01-01

The majority of foods that are consumed in our developed society have been processed. Processing promotes a non-enzymatic reaction between proteins and sugars, the Maillard reaction (MR). Maillard reaction products (MRPs) contribute to the taste, smell and color of many food products, and thus

Using Process Mining to Learn from Process Changes in Evolutionary Systems

NARCIS (Netherlands)

Günther, Christian W.; Rinderle, S.B.; Reichert, M.U.; van der Aalst, Wil M.P.; Recker, Jan

2008-01-01

Traditional information systems struggle with the requirement to provide flexibility and process support while still enforcing some degree of control. Accordingly, adaptive process management systems (PMSs) have emerged that provide some flexibility by enabling dynamic process changes during

REALIZING BUSINESS PROCESS MANAGEMENT BY HELP OF A PROCESS MAPPING DATABASE TOOL

CERN Document Server

Vergili, Ceren

2016-01-01

In a typical business sector, processes are the building blocks of the achievement. A considerable percentage of the processes are consisting of business processes. This fact is bringing the fact that business sectors are in need of a management discipline. Business Process Management (BPM) is a discipline that combines modelling, automation, execution, control, measurement, and optimization of process by considering enterprise goals, spanning systems, employees, customers, and partners. CERN’s EN – HE – HM section desires to apply the BPM discipline appropriately for improving their necessary technical, administrative and managerial actions to supply appropriate CERN industrial transport, handling and lifting equipment and to maintain it. For this reason, a Process Mapping Database Tool is created to develop a common understanding about how the section members can visualize their processes, agree on quality standards and on how to improve. It provides a management support by establishing Process Charts...

Multimodal Processes Rescheduling

DEFF Research Database (Denmark)

Bocewicz, Grzegorz; Banaszak, Zbigniew A.; Nielsen, Peter

2013-01-01

Cyclic scheduling problems concerning multimodal processes are usually observed in FMSs producing multi-type parts where the Automated Guided Vehicles System (AGVS) plays a role of a material handling system. Schedulability analysis of concurrently flowing cyclic processes (SCCP) exe-cuted in the......Cyclic scheduling problems concerning multimodal processes are usually observed in FMSs producing multi-type parts where the Automated Guided Vehicles System (AGVS) plays a role of a material handling system. Schedulability analysis of concurrently flowing cyclic processes (SCCP) exe...

Process-aware information systems : lessons to be learned from process mining

NARCIS (Netherlands)

Aalst, van der W.M.P.; Jensen, K.; Aalst, van der W.M.P.

2009-01-01

A Process-Aware Information System (PAIS) is a software system that manages and executes operational processes involving people, applications, and/or information sources on the basis of process models. Example PAISs are workflow management systems, case-handling systems, enterprise information

Applicability of product-driven process synthesis to separation processes in food

NARCIS (Netherlands)

Jankowiak, L.; Goot, van der A.J.; Trifunovic, O.; Bongers, P.; Boom, R.M.

2012-01-01

The demand for more sustainable processing in the food industry is rising but requires structured methodologies to support the fast implementation of new economic and sustainable processes. Product-driven process synthesis (PDPS) is a recently established methodology facilitating the rapid

Synroc processing options

International Nuclear Information System (INIS)

Rozsa, R.B.; Hoenig, C.L.

1981-01-01

Synroc is a titanate-based ceramic material currently being developed for immobilizing high-level nuclear reactor wastes in solid form. Synroc D is a unique variation of Synroc. It can contain the high-level defense wastes, particularly those in storage at the Savannah River Plant. In this report, we review the early development of the initial Synroc process, discuss modification and other options that simplify it overall, and recommend the future direction of research and development in the processing area. A reference Synroc process is described briefly and contrasted with the Savannah River Laboratory glass-based reference case. Preliminary engineering layouts show Synroc to be a more complex processing operation and, thus, more expensive than the glass-based process. However, we believe that simplifications, which will significantly reduce the cost difference, are possible. Further research and development will continue in the areas of slurry processing, fluidized bed calcination, and mineralization. This last will use sintering, hot uniaxial pressing, or hot isostatic pressing

Design Processes

DEFF Research Database (Denmark)

Ovesen, Nis

2009-01-01

Inspiration for most research and optimisations on design processes still seem to focus within the narrow field of the traditional design practise. The focus in this study turns to associated businesses of the design professions in order to learn from their development processes. Through interviews...... and emerging production methods....

Process modeling style

CERN Document Server

Long, John

2014-01-01

Process Modeling Style focuses on other aspects of process modeling beyond notation that are very important to practitioners. Many people who model processes focus on the specific notation used to create their drawings. While that is important, there are many other aspects to modeling, such as naming, creating identifiers, descriptions, interfaces, patterns, and creating useful process documentation. Experience author John Long focuses on those non-notational aspects of modeling, which practitioners will find invaluable. Gives solid advice for creating roles, work produ

Improving Healthcare Logistics Processes

DEFF Research Database (Denmark)

Feibert, Diana Cordes

logistics processes in hospitals and aims to provide theoretically and empirically based evidence for improving these processes to both expand the knowledge base of healthcare logistics and provide a decision tool for hospital logistics managers to improve their processes. Case studies were conducted...... processes. Furthermore, a method for benchmarking healthcare logistics processes was developed. Finally, a theoretically and empirically founded framework was developed to support managers in making an informed decision on how to improve healthcare logistics processes. This study contributes to the limited...... literature concerned with the improvement of logistics processes in hospitals. Furthermore, the developed framework provides guidance for logistics managers in hospitals on how to improve their processes given the circumstances in which they operate....

Nuclear process heat

International Nuclear Information System (INIS)

Barnert, H.; Hohn, H.; Schad, M.; Schwarz, D.; Singh, J.

1993-01-01

In a system for the application of high temperature heat from the HTR one must distinguish between the current generation and the use of process heat. In this respect it is important that the current can be generated by dual purpose power plants. The process heat is used as sensible heat, vaporisation heat and as chemical energy at the chemical conversion for the conversion of raw materials, the refinement of fossil primary energy carriers and finally circuit processes for the fission of water. These processes supply the market for heat, fuels, motor fuels and basic materials. Fifteen examples of HTR heat processes from various projects and programmes are presented in form of energy balances, however in a rather short way. (orig./DG) [de

Business process support

Energy Technology Data Exchange (ETDEWEB)

Carle, Adriana; Fiducia, Daniel [Transportadora de Gas del Sur S.A. (TGS), Buenos Aires (Argentina)

2005-07-01

This paper is about the own development of business support software. The developed applications are used to support two business processes: one of them is the process of gas transportation and the other is the natural gas processing. This software has interphases with the ERP SAP, software SCADA and on line gas transportation simulation software. The main functionalities of the applications are: entrance on line real time of clients transport nominations, transport programming, allocation of the clients transport nominations, transport control, measurements, balanced pipeline, allocation of gas volume to the gas processing plants, calculate of product tons processed in each plant and tons of product distributed to clients. All the developed software generates information to the internal staff, regulatory authorities and clients. (author)

Process for making unsaturated hydrocarbons using microchannel process technology

Science.gov (United States)

Tonkovich, Anna Lee [Dublin, OH; Yuschak, Thomas [Lewis Center, OH; LaPlante, Timothy J [Columbus, OH; Rankin, Scott [Columbus, OH; Perry, Steven T [Galloway, OH; Fitzgerald, Sean Patrick [Columbus, OH; Simmons, Wayne W [Dublin, OH; Mazanec, Terry Daymo, Eric

2011-04-12

The disclosed invention relates to a process for converting a feed composition comprising one or more hydrocarbons to a product comprising one or more unsaturated hydrocarbons, the process comprising: flowing the feed composition and steam in contact with each other in a microchannel reactor at a temperature in the range from about 200.degree. C. to about 1200.degree. C. to convert the feed composition to the product, the process being characterized by the absence of catalyst for converting the one or more hydrocarbons to one or more unsaturated hydrocarbons. Hydrogen and/or oxygen may be combined with the feed composition and steam.

Correlation between radwaste processing and hazardous waste treatment processes

International Nuclear Information System (INIS)

Block, O.U.J.; Tulipano, F.J.

1988-01-01

The basic framework under SARA has established that preferred remedies are those which permanently and significantly reduce toxicity, mobility or volume of wastes. In the 1970's radwaste process designs at power plants received pressure to satisfy essentially the same criteria when increased emphasis was placed on limited disposal sites which resulted in rapidly escalating disposal costs. This paper provides a historical perspective of radwaste experience and discusses valuable insight to hazardous waste treatment technologies. The radwaste system experience is discussed in terms of providing a source of proven and reliable technologies. Discussion is presented on specific radwaste processes which are applicable technologies for hazardous waste treatment. The technologies presented include (a) Solidification, (b) Evaporation, and (c) Incineration. Experience is presented which establishes assurance that the treatment technologies will provide a permanent remedy to hazardous waste treatment. This paper describes typical radwaste solidification, evaporation and incineration processes at power plants. The design requirements and implementation of radwaste equipment is correlated to design requirement of hazardous waste equipment. Specific discussion is provided on how the available process equipment can reduce toxicity, mobility, and volume of waste. Discussion is presented on how the standard off the shelf processing equipment needs to be modified for radwaste and hazardous waste applications

Modeling Aspects of Activated Sludge Processes Part l l: Mathematical Process Modeling and Biokinetics of Activated Sludge Processes

Energy Technology Data Exchange (ETDEWEB)

AbdElHaleem, H S [Cairo Univ.-CivlI Eng. Dept., Giza (Egypt); EI-Ahwany, A H [CairoUlmrsity- Faculty ofEngincering - Chemical Engineering Department, Giza (Egypt); Ibrahim, H I [Helwan University- Faculty of Engineering - Biomedical Engineering Department, Helwan (Egypt); Ibrahim, G [Menofia University- Faculty of Engineering Sbebin EI Kom- Basic Eng. Sc. Dept., Menofia (Egypt)

2004-07-01

Mathematical process modeling and biokinetics of activated sludge process were reviewed considering different types of models. It has been evaluated the task group models of ASMI. and 2, and 3 versioned by Henze et al considering the conditions of each model and the different processes of which every model consists. It is revealed that ASMI contains some defects avoided in ASM3. Relied on homogeneity, Models can be classified into homogenous models characterized by taking the activated sludge process as one phase. In this type of models, the internal mass transfer inside the floes was neglected.. Hence, the kinetic parameter produces can be considered inaccurate. The other type of models is the heterogeneous model This type considers the mass transfer operations in addition to the biochemical reaction processes; hence, the resulted kinetic parameters can be considered more accurate than that of homogenous type.

Modeling Aspects of Activated Sludge Processes Part l l: Mathematical Process Modeling and Biokinetics of Activated Sludge Processes

International Nuclear Information System (INIS)

AbdElHaleem, H.S.; EI-Ahwany, A. H.; Ibrahim, H.I.; Ibrahim, G.

2004-01-01

Mathematical process modeling and biokinetics of activated sludge process were reviewed considering different types of models. It has been evaluated the task group models of ASMI. and 2, and 3 versioned by Henze et al considering the conditions of each model and the different processes of which every model consists. It is revealed that ASMI contains some defects avoided in ASM3. Relied on homogeneity, Models can be classified into homogenous models characterized by taking the activated sludge process as one phase. In this type of models, the internal mass transfer inside the floes was neglected.. Hence, the kinetic parameter produces can be considered inaccurate. The other type of models is the heterogeneous model This type considers the mass transfer operations in addition to the biochemical reaction processes; hence, the resulted kinetic parameters can be considered more accurate than that of homogenous type

A Dual Process Approach to Understand Tourists’ Destination Choice Processes

DEFF Research Database (Denmark)

Kock, Florian; Josiassen, Alexander; Assaf, Albert

2017-01-01

Most studies that investigate tourists' choices of destinations apply the concept of mental destination representations, also referred to as destination image. The present study investigates tourists’ destination choice processes by conceptualizing how different components of destination image...... are mentally processed in tourists' minds. Specifically, the seminal dual processing approach is applied to the destination image literature. By doing this, we argue that some components of mental destination representations are processed systematically while others serve as inputs for heuristics...... that individuals apply to inform their decision making. Understanding how individuals make use of their mental destination representations and how they color their decision-making is essential in order to better explain tourist behavior....

Ornstein-Uhlenbeck Processes Simulation

OpenAIRE

Kuzmina, A.

2012-01-01

In this paper we give a brief introduction to Ornstein-Uhlenbeck processes and their simulation methods. Ornstein-Uhlenbeck processes were introduced by Barndorff-Nielsen and Shephard (2001) as a model to describe volatility in finance. Ornstein-Uhlenbeck processes are based on Levy processes. Levy processes simulation may be found in [1, 2].

Process heat. Triggering the processes

Energy Technology Data Exchange (ETDEWEB)

Augsten, Eva

2012-07-01

If solar process heat is to find a market, then the decision makers in industrial companies need to be aware that it actually exists. This was one of the main goals of the So-Pro project, which officially drew to a close in April 2012. (orig.)

Optimality of Poisson Processes Intensity Learning with Gaussian Processes

NARCIS (Netherlands)

Kirichenko, A.; van Zanten, H.

2015-01-01

In this paper we provide theoretical support for the so-called "Sigmoidal Gaussian Cox Process" approach to learning the intensity of an inhomogeneous Poisson process on a d-dimensional domain. This method was proposed by Adams, Murray and MacKay (ICML, 2009), who developed a tractable computational

Is There Dependence Between Process Maturity and Process Performance?

NARCIS (Netherlands)

Joost Spekschoor; Pascal Ravesteijn; Roeland Loggen; dr. Martijn Zoet

2012-01-01

During recent years the world has seen rapid changes such as globalization, the Internet, and the rise of new economies. To survive these changes organizations need to be in control of their processes, and be able to continuously improve the process performance. Therefore many organizations are

Stream-processing pipelines: processing of streams on multiprocessor architecture

NARCIS (Netherlands)

Kavaldjiev, N.K.; Smit, Gerardus Johannes Maria; Jansen, P.G.

In this paper we study the timing aspects of the operation of stream-processing applications that run on a multiprocessor architecture. Dependencies are derived for the processing and communication times of the processors in such a system. Three cases of real-time constrained operation and four

Detecting Difference between Process Models Based on the Refined Process Structure Tree

Directory of Open Access Journals (Sweden)

Jing Fan

2017-01-01

Full Text Available The development of mobile workflow management systems (mWfMS leads to large number of business process models. In the meantime, the location restriction embedded in mWfMS may result in different process models for a single business process. In order to help users quickly locate the difference and rebuild the process model, detecting the difference between different process models is needed. Existing detection methods either provide a dissimilarity value to represent the difference or use predefined difference template to generate the result, which cannot reflect the entire composition of the difference. Hence, in this paper, we present a new approach to solve this problem. Firstly, we parse the process models to their corresponding refined process structure trees (PSTs, that is, decomposing a process model into a hierarchy of subprocess models. Then we design a method to convert the PST to its corresponding task based process structure tree (TPST. As a consequence, the problem of detecting difference between two process models is transformed to detect difference between their corresponding TPSTs. Finally, we obtain the difference between two TPSTs based on the divide and conquer strategy, where the difference is described by an edit script and we make the cost of the edit script close to minimum. The extensive experimental evaluation shows that our method can meet the real requirements in terms of precision and efficiency.

Preliminary evaluation of alternative waste form solidification processes. Volume I. Identification of the processes

International Nuclear Information System (INIS)

Treat, R.L.; Nesbitt, J.F.; Blair, H.T.; Carter, J.G.; Gorton, P.S.; Partain, W.L.; Timmerman, C.L.

1980-04-01

This document contains preconceptual design data on 11 processes for the solidification and isolation of nuclear high-level liquid wastes (HLLW). The processes are: in-can glass melting (ICGM) process, joule-heated glass melting (JHGM) process, glass-ceramic (GC) process, marbles-in-lead (MIL) matrix process, supercalcine pellets-in-metal (SCPIM) matrix process, pyrolytic-carbon coated pellets-in-metal (PCCPIM) matrix process, supercalcine hot-isostatic-pressing (SCHIP) process, SYNROC hot-isostatic-pressing (SYNROC HIP) process, titanate process, concrete process, and cermet process. For the purposes of this study, it was assumed that each of the solidification processes is capable of handling similar amounts of HLLW generated in a production-sized fuel reprocessing plant. It was also assumed that each of the processes would be enclosed in a shielded canyon or cells within a waste facility located at the fuel reprocessing plant. Finally, it was assumed that all of the processes would be subject to the same set of regulations, codes and standards. Each of the solidification processes converts waste into forms that may be acceptable for geological disposal. Each process begins with the receipt of HLLW from the fuel reprocessing plant. In this study, it was assumed that the original composition of the HLLW would be the same for each process. The process ends when the different waste forms are enclosed in canisters or containers that are acceptable for interim storage. Overviews of each of the 11 processes and the bases used for their identification are presented in the first part of this report. Each process, including its equipment and its requirements, is covered in more detail in Appendices A through K. Pertinent information on the current state of the art and the research and development required for the implementation of each process are also noted in the appendices

Suppurative processes

International Nuclear Information System (INIS)

Vinner, M.G.

1983-01-01

Suppurative process in the case of bronchiectatic disease, abscess and gang rene of lungs, has been described. Characteristic signs of roentgenologic pictu re of the above-mentioned diseases are considered. It is shown,that in most cas es roentgenologic studies give a possibility to make a high-quality diagnosis of suppurative processes

Investigating the Process of Process Modeling with Eye Movement Analysis

OpenAIRE

Pinggera, Jakob; Furtner, Marco; Martini, Markus; Sachse, Pierre; Reiter, Katharina; Zugal, Stefan; Weber, Barbara

2015-01-01

Research on quality issues of business process models has recently begun to explore the process of creating process models by analyzing the modeler's interactions with the modeling environment. In this paper we aim to complement previous insights on the modeler's modeling behavior with data gathered by tracking the modeler's eye movements when engaged in the act of modeling. We present preliminary results and outline directions for future research to triangulate toward a more comprehensive un...

Radiotracer investigations of the flotation process in copper ore processing

International Nuclear Information System (INIS)

Petryka, L.; Przewlocki, K.

1983-01-01

Optimization of copper ore processing requires in particular the investigation of the flotation process. 64 Cu induced in natural ore by activation was used as a tracer. Detailed measurements were performed in an industrial flotation plant consisting of 14 cells. As a result the mean residence time of different grain size fractions of natural copper sulphide was determined for all parts of the flotation plant together with the efficiency of the flotation process. (author)

Shot-noise-weighted processes : a new family of spatial point processes

NARCIS (Netherlands)

M.N.M. van Lieshout (Marie-Colette); I.S. Molchanov (Ilya)

1995-01-01

textabstractThe paper suggests a new family of of spatial point processes distributions. They are defined by means of densities with respect to the Poisson point process within a bounded set. These densities are given in terms of a functional of the shot-noise process with a given influence

Process Management Plans

Directory of Open Access Journals (Sweden)

Tomasz Miksa

2014-07-01

Full Text Available In the era of research infrastructures and big data, sophisticated data management practices are becoming essential building blocks of successful science. Most practices follow a data-centric approach, which does not take into account the processes that created, analysed and presented the data. This fact limits the possibilities for reliable verification of results. Furthermore, it does not guarantee the reuse of research, which is one of the key aspects of credible data-driven science. For that reason, we propose the introduction of the new concept of Process Management Plans, which focus on the identification, description, sharing and preservation of the entire scientific processes. They enable verification and later reuse of result data and processes of scientific experiments. In this paper we describe the structure and explain the novelty of Process Management Plans by showing in what way they complement existing Data Management Plans. We also highlight key differences, major advantages, as well as references to tools and solutions that can facilitate the introduction of Process Management Plans.

DECAB: process development of a phase change absorption process

NARCIS (Netherlands)

Sanchez Fernandez, E.; Goetheer, E.L.V.

2011-01-01

This work describes the conceptual design of a novel separation process for CO2 removal from flue gas based on precipitating solvents. The process here described (DECAB) is an enhanced CO2 absorption based on the Le Chatelier's principle, which states that reaction equilibrium can be shifted by

The H-Oil process: a worldwide leader in vacuum residue hydro processing

Energy Technology Data Exchange (ETDEWEB)

Colyar, J.J.; Wisdom, L.I.; Koskas, A.

1996-12-31

The h-Oil process is a catalytic hydrocracking process which is used to convert and upgrade petroleum residua and heavy oils. This paper discusses additional background information on the H-Oil process, some of the key advances made to the process and applications for the Latin America market. 5 refs., 6 tabs.., 2 figs.

Development of the Log-in Process and the Operation Process for the VHTR-SI Process Dynamic Simulation Code

International Nuclear Information System (INIS)

Chang, Jiwoon; Shin, Youngjoon; Kim, Jihwan; Lee, Kiyoung; Lee, Wonjae; Chang, Jonghwa; Youn, Cheung

2009-01-01

The VHTR-SI process is a hydrogen production technique by using Sulfur and Iodine. The SI process for a hydrogen production uses a high temperature (about 950 .deg. C) of the He gas which is a cooling material for an energy sources. The Korea Atomic Energy Research Institute Dynamic Simulation Code (KAERI DySCo) is an integration application software that simulates the dynamic behavior of the VHTR-SI process. A dynamic modeling is used to express and model the behavior of the software system over time. The dynamic modeling deals with the control flow of system, the interaction of objects and the order of actions in view of a time and transition by using a sequence diagram and a state transition diagram. In this paper, we present an user log-in process and an operation process for the KAERI DySCo by using a sequence diagram and a state transition diagram

Quantifying Quantum-Mechanical Processes.

Science.gov (United States)

Hsieh, Jen-Hsiang; Chen, Shih-Hsuan; Li, Che-Ming

2017-10-19

The act of describing how a physical process changes a system is the basis for understanding observed phenomena. For quantum-mechanical processes in particular, the affect of processes on quantum states profoundly advances our knowledge of the natural world, from understanding counter-intuitive concepts to the development of wholly quantum-mechanical technology. Here, we show that quantum-mechanical processes can be quantified using a generic classical-process model through which any classical strategies of mimicry can be ruled out. We demonstrate the success of this formalism using fundamental processes postulated in quantum mechanics, the dynamics of open quantum systems, quantum-information processing, the fusion of entangled photon pairs, and the energy transfer in a photosynthetic pigment-protein complex. Since our framework does not depend on any specifics of the states being processed, it reveals a new class of correlations in the hierarchy between entanglement and Einstein-Podolsky-Rosen steering and paves the way for the elaboration of a generic method for quantifying physical processes.

Hydrogen production processes

International Nuclear Information System (INIS)

2003-01-01

The goals of this first Gedepeon workshop on hydrogen production processes are: to stimulate the information exchange about research programs and research advances in the domain of hydrogen production processes, to indicate the domains of interest of these processes and the potentialities linked with the coupling of a nuclear reactor, to establish the actions of common interest for the CEA, the CNRS, and eventually EDF, that can be funded in the framework of the Gedepeon research group. This document gathers the slides of the 17 presentations given at this workshop and dealing with: the H 2 question and the international research programs (Lucchese P.); the CEA's research program (Lucchese P., Anzieu P.); processes based on the iodine/sulfur cycle: efficiency of a facility - flow-sheets, efficiencies, hard points (Borgard J.M.), R and D about the I/S cycle: Bunsen reaction (Colette S.), R and D about the I/S cycle: the HI/I 2 /H 2 O system (Doizi D.), demonstration loop/chemical engineering (Duhamet J.), materials and corrosion (Terlain A.); other processes under study: the Westinghouse cycle (Eysseric C.), other processes under study at the CEA (UT3, plasma,...) (Lemort F.), database about thermochemical cycles (Abanades S.), Zn/ZnO cycle (Broust F.), H 2 production by cracking, high temperature reforming with carbon trapping (Flamant G.), membrane technology (De Lamare J.); high-temperature electrolysis: SOFC used as electrolyzers (Grastien R.); generic aspects linked with hydrogen production: technical-economical evaluation of processes (Werkoff F.), thermodynamic tools (Neveu P.), the reactor-process coupling (Aujollet P.). (J.S.)

Materials, process, product analysis of coal process technology. Phase I final report

Energy Technology Data Exchange (ETDEWEB)

Saxton, J. C.; Roig, R. W.; Loridan, A.; Leggett, N. E.; Capell, R. G.; Humpstone, C. C.; Mudry, R. N.; Ayres, E.

1976-02-01

The purpose of materials-process-product analysis is a systematic evaluation of alternative manufacturing processes--in this case processes for converting coal into energy and material products that can supplement or replace petroleum-based products. The methodological steps in the analysis include: Definition of functional operations that enter into coal conversion processes, and modeling of alternative, competing methods to accomplish these functions; compilation of all feasible conversion processes that can be assembled from combinations of competing methods for the functional operations; systematic, iterative evaluation of all feasible conversion processes under a variety of economic situations, environmental constraints, and projected technological advances; and aggregative assessments (economic and environmental) of various industrial development scenarios. An integral part of the present project is additional development of the existing computer model to include: A data base for coal-related materials and coal conversion processes; and an algorithmic structure that facilitates the iterative, systematic evaluations in response to exogenously specified variables, such as tax policy, environmental limitations, and changes in process technology and costs. As an analytical tool, the analysis is intended to satisfy the needs of an analyst working at the process selection level, for example, with respect to the allocation of RDandD funds to competing technologies.

Process for separating nitrogen from methane using microchannel process technology

Science.gov (United States)

Tonkovich, Anna Lee [Marysville, OH; Qiu, Dongming [Dublin, OH; Dritz, Terence Andrew [Worthington, OH; Neagle, Paul [Westerville, OH; Litt, Robert Dwayne [Westerville, OH; Arora, Ravi [Dublin, OH; Lamont, Michael Jay [Hilliard, OH; Pagnotto, Kristina M [Cincinnati, OH

2007-07-31

The disclosed invention relates to a process for separating methane or nitrogen from a fluid mixture comprising methane and nitrogen, the process comprising: (A) flowing the fluid mixture into a microchannel separator, the microchannel separator comprising a plurality of process microchannels containing a sorption medium, the fluid mixture being maintained in the microchannel separator until at least part of the methane or nitrogen is sorbed by the sorption medium, and removing non-sorbed parts of the fluid mixture from the microchannel separator; and (B) desorbing the methane or nitrogen from the sorption medium and removing the desorbed methane or nitrogen from the microchannel separator. The process is suitable for upgrading methane from coal mines, landfills, and other sub-quality sources.

Business process reporting using process mining, analytic workflows and process cubes : A case study in education

NARCIS (Netherlands)

Bolt Iriondo, A.J.; de Leoni, M.; van der Aalst, W.M.P.; Gorissen, P.; Paolo, C.; Stefanie, R.-M.

2017-01-01

Business Process Intelligence (BPI) is an emerging topic that has gained popularity in the last decade. It is driven by the need for analysis techniques that allow businesses to understand and improve their processes. One of the most common applications of BPI is reporting, which consists on the

The plasma hearth process: Process residuals characterization

International Nuclear Information System (INIS)

Leatherman, G.L.; Geimer, R.; Batdorf, J.; Hassel, G.; Wolfe, P.; Carney, K.P.

1994-01-01

The Plasma Hearth Process (PHP) is a high-temperature waste treatment process being developed by Science Applications International Corporation (SAIC) for the Department of Energy (DOE) that destroys hazardous organics while stabilizing radionuclides and hazardous metals in a vitreous slag waste form. The PHP has potential application for the treatment of a wide range of mixed waste types in both the low-level and transuranic (TRU) mixed waste categories. DOE, through the Office of Technology Development's Mixed Waste Integrated Program (MWIP) is conducting a three phase development project to ready the PHP for implementation in the DOE complex

Process and device for processing radioactive wastes

International Nuclear Information System (INIS)

1974-01-01

A method is described for processing liquid radioactive wastes. It includes the heating of the liquid wastes so that the contained liquids are evaporated and a practically anhydrous mass of solid particles inferior in volume to that of the wastes introduced is formed, then the transformation of the solid particles into a monolithic structure. This transformation includes the compressing of the particles and sintering or fusion. The solidifying agent is a mixture of polyethylene and paraffin wax or a styrene copolymer and a polyester resin. The device used for processing the radioactive liquid wastes is also described [fr

Fermentation process using specific oxygen uptake rates as a process control

Science.gov (United States)

Van Hoek, Pim [Minnetonka, MN; Aristidou, Aristos [Maple Grove, MN; Rush, Brian [Minneapolis, MN

2011-05-10

Specific oxygen uptake (OUR) is used as a process control parameter in fermentation processes. OUR is determined during at least the production phase of a fermentation process, and process parameters are adjusted to maintain the OUR within desired ranges. The invention is particularly applicable when the fermentation is conducted using a microorganism having a natural PDC pathway that has been disrupted so that it no longer functions. Microorganisms of this sort often produce poorly under strictly anaerobic conditions. Microaeration controlled by monitoring OUR allows the performance of the microorganism to be optimized.

Photon technology. Laser processing technology; Photon technology. Laser process gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Survey has been conducted to develop laser processing technology utilizing the interaction between substance and photon. This is a part of the leading research on photon technology development. The photon technology development is aimed at novel technology development highly utilizing the quantum nature of photons. In the field of laser processing, high quality photons are used as tools, special functions of atoms and molecules will be discovered, and processing for functional fabrication (photon machining) will be established. A role of laser processing in industries has become significant, which is currently spreading not only into cutting and welding of materials and scalpels but also into such a special field as ultrafine processing of materials. The spreading is sometimes obstructed due to the difficulty of procurement of suitable machines and materials, and the increase of cost. The purpose of this study is to develop the optimal laser technology, to elucidate the interaction between substance and photon, and to develop the laser system and the transmission and regulation systems which realize the optimal conditions. 387 refs., 115 figs., 25 tabs.

Process Technical Basis Documentation Diagram for a solid-waste processing facility

International Nuclear Information System (INIS)

Benar, C.J.; Petersen, C.A.

1994-02-01

The Process Technical Basis Documentation Diagram is for a solid-waste processing facility that could be designed to treat, package, and certify contact-handled mixed low-level waste for permanent disposal. The treatment processes include stabilization using cementitious materials and immobilization using a polymer material. The Diagram identifies several engineering/demonstration activities that would confirm the process selection and process design. An independent peer review was conducted at the request of Westinghouse Hanford Company to determine the technical adequacy of the technical approach for waste form development. The peer review panel provided comments and identified documents that it felt were needed in the Diagram as precedence for Title I design. The Diagram is a visual tool to identify traceable documentation of key activities, including those documents suggested by the peer review, and to show how they relate to each other. The Diagram is divided into three sections: (1) the Facility section, which contains documents pertaining to the facility design, (2) the Process Demonstration section, which contains documents pertaining to the process engineering/demonstration work, and 3) the Regulatory section, which contains documents describing the compliance strategy for each acceptance requirement for each feed type, and how this strategy will be implemented

Flue Gas Desulphurization Processes

International Nuclear Information System (INIS)

Aly, A.I.M.; Halhouli, K.A.; Abu-Ashur, B.M.

1999-01-01

Flue gas desulphurization process are discussed. These processes can be grouped into non-regenerable systems and regenerable systems. The non-regenerable systems produce a product which is either disposed of as waste or sold as a by-product e.g. lime/limestone process. While in the regenerable systems, e.g. Wellman-Lord process, the SO 2 is regenerated from the sorbent(sodium sulphite), which is returned to absorb more SO 2 . Also a newer technology for flue gas desulphurization is discussed. The Ispra process uses bromine as oxidant, producing HBr, from which bromine is regenerated by electrolysis. The only by-products of this process are sulphuric acid and hydrogen, which are both valuable products, and no waste products are produced. Suggested modifications on the process are made based on experimental investigations to improve the efficiency of the process and to reduce its costs

BPMN process views construction

NARCIS (Netherlands)

Yongchareon, S.; Liu, Chengfei; Zhao, X.; Kowalkiewicz, M.; Kitagawa, H.; Ishikawa, Y.

2010-01-01

Process view technology is catching more attentions in modern business process management, as it enables the customisation of business process representation. This capability helps improve the privacy protection, authority control, flexible display, etc., in business process modelling. One of

Visual processing in rapid-chase systems: Image processing, attention, and awareness

Directory of Open Access Journals (Sweden)

Thomas eSchmidt

2011-07-01

Full Text Available Visual stimuli can be classified so rapidly that their analysis may be based on a single sweep of feedforward processing through the visuomotor system. Behavioral criteria for feedforward processing can be evaluated in response priming tasks where speeded pointing or keypress responses are performed towards target stimuli which are preceded by prime stimuli. We apply this method to several classes of complex stimuli. 1 When participants classify natural images into animals or non-animals, the time course of their pointing responses indicates that prime and target signals remain strictly sequential throughout all processing stages, meeting stringent behavioral criteria for feedforward processing (rapid-chase criteria. 2 Such priming effects are boosted by selective visual attention for positions, shapes, and colors, in a way consistent with bottom-up enhancement of visuomotor processing, even when primes cannot be consciously identified. 3 Speeded processing of phobic images is observed in participants specifically fearful of spiders or snakes, suggesting enhancement of feedforward processing by long-term perceptual learning. 4 When the perceived brightness of primes in complex displays is altered by means of illumination or transparency illusions, priming effects in speeded keypress responses can systematically contradict subjective brightness judgments, such that one prime appears brighter than the other but activates motor responses as if it was darker. We propose that response priming captures the output of the first feedforward pass of visual signals through the visuomotor system, and that this output lacks some characteristic features of more elaborate, recurrent processing. This way, visuomotor measures may become dissociated from several aspects of conscious vision. We argue that "fast" visuomotor measures predominantly driven by feedforward processing should supplement "slow" psychophysical measures predominantly based on visual

A survey of process control computers at the Idaho Chemical Processing Plant

International Nuclear Information System (INIS)

Dahl, C.A.

1989-01-01

The Idaho Chemical Processing Plant (ICPP) at the Idaho National Engineering Laboratory is charged with the safe processing of spent nuclear fuel elements for the United States Department of Energy. The ICPP was originally constructed in the late 1950s and used state-of-the-art technology for process control at that time. The state of process control instrumentation at the ICPP has steadily improved to keep pace with emerging technology. Today, the ICPP is a college of emerging computer technology in process control with some systems as simple as standalone measurement computers while others are state-of-the-art distributed control systems controlling the operations in an entire facility within the plant. The ICPP has made maximal use of process computer technology aimed at increasing surety, safety, and efficiency of the process operations. Many benefits have been derived from the use of the computers for minimal costs, including decreased misoperations in the facility, and more benefits are expected in the future

Hydroforming of Tesla Cavities at Desy

International Nuclear Information System (INIS)

Singer, W.; Kaiser, H.; Singer, X.; Gonin, I.; Zhelezov, I.; Khabibullin, T.; Kneisel, P.; Saito, K.

2000-01-01

Since several years the development of seamless niobium cavity fabrication by hydro forming is being pursued at DESY. This technique offers the possibility of lower cost of fabrication and perhaps better rf performance of the cavities because of the elimination of electron-beam welds, which in the standard fabrication technique have sometimes lead to inferior cavity performance due to defects. Several single cell 1300 MHz cavities have been formed from high purity seamless niobium tubes, which are under computer control expanded with internal pressure while simultaneously being swaged axially. The seamless tubes have been made by either back extrusion and flow forming or by spinning or deep drawing. Standard surface treatment techniques such as high temperature post purification, buffered chemical polishing (BCP), electropolishing (EP) and high pressure ultra pure water rinsing (HPR) have been applied to these cavities. The cavities exhibited high Q - values of 2 x 10 10 at 2K and residual resistances as low as 3 n(Omega) after the removal of a surface layer of app. 100 (micro)m by BCP. Surprisingly, even at high gradients up to the maximum measured values of E acc ∼ 33 MV/m the Q-value did not decrease in the absence of field emission as often observed. After electropolishing of additional 100 (micro)m one of the cavities reached an accelerating gradient of E acc (ge) 42 MV/m

Process evaluation distributed system

Science.gov (United States)

Moffatt, Christopher L. (Inventor)

2006-01-01

The distributed system includes a database server, an administration module, a process evaluation module, and a data display module. The administration module is in communication with the database server for providing observation criteria information to the database server. The process evaluation module is in communication with the database server for obtaining the observation criteria information from the database server and collecting process data based on the observation criteria information. The process evaluation module utilizes a personal digital assistant (PDA). A data display module in communication with the database server, including a website for viewing collected process data in a desired metrics form, the data display module also for providing desired editing and modification of the collected process data. The connectivity established by the database server to the administration module, the process evaluation module, and the data display module, minimizes the requirement for manual input of the collected process data.

Development of processes for the utilization of Brazilian coal using nuclear process heat and/or nuclear process steam

International Nuclear Information System (INIS)

Bamert, H.; Niessen, H.F.; Walbeck, M.; Wasrzik, U.; Mueller, R.; Schiffers, U.; Strauss, W.

1980-01-01

Status of the project: End of the project definition phase and preparation of the planned conceptual phase. Objective of the project: Development of processes for the utilization of nuclear process heat and/or nuclear process steam for the gasification of coal with high ash content, in particular coal from Brazil. Results: With the data of Brazilian coal of high ash content (mine Leao/ 43% ash in the mine-mouth quality, 20% ash after preparation) there have been worked out proposals for the mine planning and for a number of processes. On the basis of these proposals and under consideration of the main data specified by the Brazilian working group there have been choosen two processes and worked out in a conceptual design: 1) pressurized water reactor + LURGI-pressure gasifier/hydrogasification for the production of SNG and 2) high temperature reactor steam gasification for the production of town gas. The economic evaluation showed that the two processes are not substantially different in their cost efficiency and they are economical on a long-term basis. For more specific design work there has been planned the implementation of an experimental programme using the semi-technical plants 'hydrogasification' in Wesseling and 'steam gasification' in Essen as the conceptual phase. (orig.) [de

Improving the Document Development Process: Integrating Relational Data and Statistical Process Control.

Science.gov (United States)

Miller, John

1994-01-01

Presents an approach to document numbering, document titling, and process measurement which, when used with fundamental techniques of statistical process control, reveals meaningful process-element variation as well as nominal productivity models. (SR)

Fuel processing. Wastes processing

International Nuclear Information System (INIS)

Bourgeois, M.

2000-01-01

The gaseous, liquid and solid radioactive effluents generated by the fuel reprocessing, can't be release in the environment. They have to be treated in order to respect the limits of the pollution regulations. These processing are detailed and discussed in this technical paper. A second part is devoted to the SPIN research program relative to the separation of the long life radionuclides in order to reduce the radioactive wastes storage volume. (A.L.B.)

Exploring processes and deviations

NARCIS (Netherlands)

Leemans, S.J.J.; Fahland, D.; Aalst, van der W.M.P.; Fournier, F.; Mendling, J.

2015-01-01

In process mining, one of the main challenges is to discover a process model, while balancing several quality criteria. This often requires repeatedly setting parameters, discovering a map and evaluating it, which we refer to as process exploration. Commercial process mining tools like Disco,

Process for winning uranium from wet process phosphoric acid

International Nuclear Information System (INIS)

1980-01-01

A process is described for winning uranium from wet process phosphoric acid by means of liquid-liquid extraction with organic phosphoric acid esters. The process is optimised by keeping the sulphate percentage in the phosphoric acid below 2% by weight, and preferably below 0.6% by weight, as compared to P 2 O 5 in the phosphoric acid. This is achieved by adding an excess of Ba and/or Ca carbonate or sulfide solution and filtering off the formed calcium and/or barium sulphate precipitates. Solid KClO 3 is then added to the filtrate to oxidise U 4+ to U 6+ . The normal extraction procedure using organic phosphoric esters as extraction liquid, can then be applied. (Th.P.)

Product- and Process Units in the CRITT Translation Process Research Database

DEFF Research Database (Denmark)

Carl, Michael

than 300 hours of text production. The database provides the raw logging data, as well as Tables of pre-processed product- and processing units. The TPR-DB includes various types of simple and composed product and process units that are intended to support the analysis and modelling of human text......The first version of the "Translation Process Research Database" (TPR DB v1.0) was released In August 2012, containing logging data of more than 400 translation and text production sessions. The current version of the TPR DB, (v1.4), contains data from more than 940 sessions, which represents more...

Poisson branching point processes

International Nuclear Information System (INIS)

Matsuo, K.; Teich, M.C.; Saleh, B.E.A.

1984-01-01

We investigate the statistical properties of a special branching point process. The initial process is assumed to be a homogeneous Poisson point process (HPP). The initiating events at each branching stage are carried forward to the following stage. In addition, each initiating event independently contributes a nonstationary Poisson point process (whose rate is a specified function) located at that point. The additional contributions from all points of a given stage constitute a doubly stochastic Poisson point process (DSPP) whose rate is a filtered version of the initiating point process at that stage. The process studied is a generalization of a Poisson branching process in which random time delays are permitted in the generation of events. Particular attention is given to the limit in which the number of branching stages is infinite while the average number of added events per event of the previous stage is infinitesimal. In the special case when the branching is instantaneous this limit of continuous branching corresponds to the well-known Yule--Furry process with an initial Poisson population. The Poisson branching point process provides a useful description for many problems in various scientific disciplines, such as the behavior of electron multipliers, neutron chain reactions, and cosmic ray showers

Investigation of Mediational Processes Using Parallel Process Latent Growth Curve Modeling

Science.gov (United States)

Cheong, JeeWon; MacKinnon, David P.; Khoo, Siek Toon

2010-01-01

This study investigated a method to evaluate mediational processes using latent growth curve modeling. The mediator and the outcome measured across multiple time points were viewed as 2 separate parallel processes. The mediational process was defined as the independent variable influencing the growth of the mediator, which, in turn, affected the growth of the outcome. To illustrate modeling procedures, empirical data from a longitudinal drug prevention program, Adolescents Training and Learning to Avoid Steroids, were used. The program effects on the growth of the mediator and the growth of the outcome were examined first in a 2-group structural equation model. The mediational process was then modeled and tested in a parallel process latent growth curve model by relating the prevention program condition, the growth rate factor of the mediator, and the growth rate factor of the outcome. PMID:20157639

A Campbell random process

International Nuclear Information System (INIS)

Reuss, J.D.; Misguich, J.H.

1993-02-01

The Campbell process is a stationary random process which can have various correlation functions, according to the choice of an elementary response function. The statistical properties of this process are presented. A numerical algorithm and a subroutine for generating such a process is built up and tested, for the physically interesting case of a Campbell process with Gaussian correlations. The (non-Gaussian) probability distribution appears to be similar to the Gamma distribution

Weak convergence of marked point processes generated by crossings of multivariate jump processes

DEFF Research Database (Denmark)

Tamborrino, Massimiliano; Sacerdote, Laura; Jacobsen, Martin

2014-01-01

We consider the multivariate point process determined by the crossing times of the components of a multivariate jump process through a multivariate boundary, assuming to reset each component to an initial value after its boundary crossing. We prove that this point process converges weakly...... process converging to a multivariate Ornstein–Uhlenbeck process is discussed as a guideline for applying diffusion limits for jump processes. We apply our theoretical findings to neural network modeling. The proposed model gives a mathematical foundation to the generalization of the class of Leaky...

Business process quality management

NARCIS (Netherlands)

Reijers, H.A.; Mendling, J.; Recker, J.; Brocke, vom J.; Rosemann, M.

2010-01-01

Abstract Process modeling is a central element in any approach to Business Process Management (BPM). However, what hinders both practitioners and aca demics is the lack of support for assessing the quality of process models — let alone realizing high quality process models. Existing frameworks are

Distributed genetic process mining

NARCIS (Netherlands)

Bratosin, C.C.; Sidorova, N.; Aalst, van der W.M.P.

2010-01-01

Process mining aims at discovering process models from data logs in order to offer insight into the real use of information systems. Most of the existing process mining algorithms fail to discover complex constructs or have problems dealing with noise and infrequent behavior. The genetic process

7 Processes that Enable NASA Software Engineering Technologies: Value-Added Process Engineering

Science.gov (United States)

Housch, Helen; Godfrey, Sally

2011-01-01

The presentation reviews Agency process requirements and the purpose, benefits, and experiences or seven software engineering processes. The processes include: product integration, configuration management, verification, software assurance, measurement and analysis, requirements management, and planning and monitoring.

Motivated information processing and group decision-making : Effects of process accountability on information processing and decision quality

NARCIS (Netherlands)

Scholten, Lotte; van Knippenberg, Daan; Nijstad, Bernard A.; De Dreu, Carsten K. W.

Integrating dual-process models [Chaiken, S., & Trope, Y. (Eds.). (1999). Dual-process theories in social psychology. NewYork: Guilford Press] with work on information sharing and group decision-making [Stasser, G., & Titus, W. (1985). Pooling of unshared information in group decision making: biased

FFTF gas processing systems

International Nuclear Information System (INIS)

Halverson, T.G.

1977-01-01

The design and operation of the two radioactive gas processing systems at the Fast Flux Test Facility (FFTF) exemplifies the concept that will be used in the first generation of Liquid Metal Fast Breeder Reactors (LMFBR's). The two systems, the Radioactive Argon Processing System (RAPS) and the Cell Atmosphere Processing System (CAPS), process the argon and nitrogen used in the FFTF for cover gas on liquid metal systems and as inert atmospheres in steel lined cells housing sodium equipment. The RAPS specifically processes the argon cover gas from the reactor coolant system, providing for decontamination and eventual reuse. The CAPS processes radioactive gasses from inerted cells and other liquid metal cover gas systems, providing for decontamination and ultimate discharge to the atmosphere. The cryogenic processing of waste gas by both systems is described

Sustainable Process Synthesis-Intensification

DEFF Research Database (Denmark)

Babi, Deenesh Kavi; Holtbruegge, Johannes; Lutze, Philip

2014-01-01

Sustainable process design can be achieved by performing process synthesis and process intensification together. This approach first defines a design target through a sustainability analysis and then finds design alternatives that match the target through process intensification. A systematic......, multi-stage framework for process synthesis- intensification that identifies more sustainable process designs has been developed. At stages 1-2, the working scale is at the level of unit operations, where a base case design is identified and analyzed with respect to sustainability metrics. At stages 3......, a phenomena-based process synthesis method is applied, where the phenomena involved in each tasks are identified, manipulated and recombined to generate new and/or existing unit operations configured into flowsheets that are more sustainable from those found in the previous levels. An overview of the key...

Feller processes: the next generation in modeling. Brownian motion, Lévy processes and beyond.

Directory of Open Access Journals (Sweden)

Björn Böttcher

Full Text Available We present a simple construction method for Feller processes and a framework for the generation of sample paths of Feller processes. The construction is based on state space dependent mixing of Lévy processes. Brownian Motion is one of the most frequently used continuous time Markov processes in applications. In recent years also Lévy processes, of which Brownian Motion is a special case, have become increasingly popular. Lévy processes are spatially homogeneous, but empirical data often suggest the use of spatially inhomogeneous processes. Thus it seems necessary to go to the next level of generalization: Feller processes. These include Lévy processes and in particular brownian motion as special cases but allow spatial inhomogeneities. Many properties of Feller processes are known, but proving the very existence is, in general, very technical. Moreover, an applicable framework for the generation of sample paths of a Feller process was missing. We explain, with practitioners in mind, how to overcome both of these obstacles. In particular our simulation technique allows to apply Monte Carlo methods to Feller processes.

Standard Model processes

CERN Document Server

Mangano, M.L.; Aguilar-Saavedra, Juan Antonio; Alekhin, S.; Badger, S.; Bauer, C.W.; Becher, T.; Bertone, V.; Bonvini, M.; Boselli, S.; Bothmann, E.; Boughezal, R.; Cacciari, M.; Carloni Calame, C.M.; Caola, F.; Campbell, J.M.; Carrazza, S.; Chiesa, M.; Cieri, L.; Cimaglia, F.; Febres Cordero, F.; Ferrarese, P.; D'Enterria, D.; Ferrera, G.; Garcia i Tormo, X.; Garzelli, M.V.; Germann, E.; Hirschi, V.; Han, T.; Ita, H.; Jäger, B.; Kallweit, S.; Karlberg, A.; Kuttimalai, S.; Krauss, F.; Larkoski, A.J.; Lindert, J.; Luisoni, G.; Maierhöfer, P.; Mattelaer, O.; Martinez, H.; Moch, S.; Montagna, G.; Moretti, M.; Nason, P.; Nicrosini, O.; Oleari, C.; Pagani, D.; Papaefstathiou, A.; Petriello, F.; Piccinini, F.; Pierini, M.; Pierog, T.; Pozzorini, S.; Re, E.; Robens, T.; Rojo, J.; Ruiz, R.; Sakurai, K.; Salam, G.P.; Salfelder, L.; Schönherr, M.; Schulze, M.; Schumann, S.; Selvaggi, M.; Shivaji, A.; Siodmok, A.; Skands, P.; Torrielli, P.; Tramontano, F.; Tsinikos, I.; Tweedie, B.; Vicini, A.; Westhoff, S.; Zaro, M.; Zeppenfeld, D.; CERN. Geneva. ATS Department

2017-06-22

This report summarises the properties of Standard Model processes at the 100 TeV pp collider. We document the production rates and typical distributions for a number of benchmark Standard Model processes, and discuss new dynamical phenomena arising at the highest energies available at this collider. We discuss the intrinsic physics interest in the measurement of these Standard Model processes, as well as their role as backgrounds for New Physics searches.

Classical higher-order processes

DEFF Research Database (Denmark)

Montesi, Fabrizio

2017-01-01

Classical Processes (CP) is a calculus where the proof theory of classical linear logic types processes à la Π-calculus, building on a Curry-Howard correspondence between session types and linear propositions. We contribute to this research line by extending CP with process mobility, inspired...... by the Higher-Order Π-calculus. The key to our calculus is that sequents are asymmetric: one side types sessions as in CP and the other types process variables, which can be instantiated with process values. The controlled interaction between the two sides ensures that process variables can be used at will......, but always respecting the linear usage of sessions expected by the environment....

Process margin enhancement for 0.25-μm metal etch process

Science.gov (United States)

Lee, Chung Y.; Ma, Wei Wen; Lim, Eng H.; Cheng, Alex T.; Joy, Raymond; Ross, Matthew F.; Wong, Selmer S.; Marlowe, Trey

2000-06-01

This study evaluates electron beam stabilization of UV6, a positive tone Deep-UV (DUV) resist from Shipley, for a 0.25 micrometer metal etch application. Results are compared between untreated resist and resist treated with different levels of electron beam stabilization. The electron beam processing was carried out in an ElectronCureTM flood electron beam exposure system from Honeywell International Inc., Electron Vision. The ElectronCureTM system utilizes a flood electron beam source which is larger in diameter than the substrate being processed, and is capable of variable energy so that the electron range is matched to the resist film thickness. Changes in the UV6 resist material as a result of the electron beam stabilization are monitored via spectroscopic ellipsometry for film thickness and index of refraction changes and FTIR for analysis of chemical changes. Thermal flow stability is evaluated by applying hot plate bakes of 150 degrees Celsius and 200 degrees Celsius, to patterned resist wafers with no treatment and with an electron beam dose level of 2000 (mu) C/cm2. A significant improvement in the thermal flow stability of the patterned UV6 resist features is achieved with the electron beam stabilization process. Etch process performance of the UV6 resist was evaluated by performing a metal pattern transfer process on wafers with untreated resist and comparing these with etch results on wafers with different levels of electron beam stabilization. The etch processing was carried out in an Applied Materials reactor with an etch chemistry including BCl3 and Cl2. All wafers were etched under the same conditions and the resist was treated after etch to prevent further erosion after etch but before SEM analysis. Post metal etch SEM cross-sections show the enhancement in etch resistance provided by the electron beam stabilization process. Enhanced process margin is achieved as a result of the improved etch resistance, and is observed in reduced resist side

Quality Control in Automated Manufacturing Processes – Combined Features for Image Processing

Directory of Open Access Journals (Sweden)

B. Kuhlenkötter

2006-01-01

Full Text Available In production processes the use of image processing systems is widespread. Hardware solutions and cameras respectively are available for nearly every application. One important challenge of image processing systems is the development and selection of appropriate algorithms and software solutions in order to realise ambitious quality control for production processes. This article characterises the development of innovative software by combining features for an automatic defect classification on product surfaces. The artificial intelligent method Support Vector Machine (SVM is used to execute the classification task according to the combined features. This software is one crucial element for the automation of a manually operated production process. 

The creation of process redesigns by selecting, transforming and replacing process parts

NARCIS (Netherlands)

Netjes, M.; Reijers, H.A.; Aalst, van der W.M.P.

2008-01-01

For companies to sustain competitive advantages, it is required to redesign and improve business processes continuously by monitoring and analyzing process enactment results. Furthermore, organizational structures must be redesigned according to the changes in business processes. However, there are

Hierarchical process memory: memory as an integral component of information processing

Science.gov (United States)

Hasson, Uri; Chen, Janice; Honey, Christopher J.

2015-01-01

Models of working memory commonly focus on how information is encoded into and retrieved from storage at specific moments. However, in the majority of real-life processes, past information is used continuously to process incoming information across multiple timescales. Considering single unit, electrocorticography, and functional imaging data, we argue that (i) virtually all cortical circuits can accumulate information over time, and (ii) the timescales of accumulation vary hierarchically, from early sensory areas with short processing timescales (tens to hundreds of milliseconds) to higher-order areas with long processing timescales (many seconds to minutes). In this hierarchical systems perspective, memory is not restricted to a few localized stores, but is intrinsic to information processing that unfolds throughout the brain on multiple timescales. “The present contains nothing more than the past, and what is found in the effect was already in the cause.”Henri L Bergson PMID:25980649

Process mining applied to the test process of wafer steppers in ASML

NARCIS (Netherlands)

Rozinat, A.; Jong, de I.S.M.; Günther, C.W.; Aalst, van der W.M.P.

2009-01-01

Process mining techniques attempt to extract nontrivial and useful information from event logs. For example, there are many process mining techniques to automatically discover a process model describing the causal dependencies between activities. Several successful case studies have been reported in

Welding process

International Nuclear Information System (INIS)

Abdul Nassir Ibrahim; Azali Muhammad; Ab. Razak Hamzah; Abd. Aziz Mohamed; Mohamad Pauzi Ismail

2008-01-01

For the final chapter of this book, there is basic introduction on welding process. The good radiography must know somehow on welding process so that they can know what kind of welding that must rejected or not. All of the exposure technique that mention in earlier chapter almost applicable in this field because welding process is critical problem if there is no inspection will be done. So, for this chapter, all the discontinuity that usually appeared will be discussed and there is another discontinuity maybe not to important and do not give big impact if found it, do not described here. On top of that, the decision to accept or reject based on code, standard and specification that agreed by both to make sure that decision that agreed is corrected and more meaningful.

Multivariate supOU processes

DEFF Research Database (Denmark)

Barndorff-Nielsen, Ole Eiler; Stelzer, Robert

Univariate superpositions of Ornstein-Uhlenbeck (OU) type processes, called supOU processes, provide a class of continuous time processes capable of exhibiting long memory behaviour. This paper introduces multivariate supOU processes and gives conditions for their existence and finiteness...... of moments. Moreover, the second order moment structure is explicitly calculated, and examples exhibit the possibility of long range dependence. Our supOU processes are defined via homogeneous and factorisable Lévy bases. We show that the behaviour of supOU processes is particularly nice when the mean...... reversion parameter is restricted to normal matrices and especially to strictly negative definite ones.For finite variation Lévy bases we are able to give conditions for supOU processes to have locally bounded càdlàg paths of finite variation and to show an analogue of the stochastic differential equation...

Multivariate supOU processes

DEFF Research Database (Denmark)

Barndorff-Nielsen, Ole Eiler; Stelzer, Robert

2011-01-01

Univariate superpositions of Ornstein–Uhlenbeck-type processes (OU), called supOU processes, provide a class of continuous time processes capable of exhibiting long memory behavior. This paper introduces multivariate supOU processes and gives conditions for their existence and finiteness of moments....... Moreover, the second-order moment structure is explicitly calculated, and examples exhibit the possibility of long-range dependence. Our supOU processes are defined via homogeneous and factorizable Lévy bases. We show that the behavior of supOU processes is particularly nice when the mean reversion...... parameter is restricted to normal matrices and especially to strictly negative definite ones. For finite variation Lévy bases we are able to give conditions for supOU processes to have locally bounded càdlàg paths of finite variation and to show an analogue of the stochastic differential equation of OU...

Rapid process development of chromatographic process using direct analysis in real time mass spectrometry as a process analytical technology tool.

Science.gov (United States)

Yan, Binjun; Chen, Teng; Xu, Zhilin; Qu, Haibin

2014-06-01

The concept of quality by design (QbD) is widely applied in the process development of pharmaceuticals. However, the additional cost and time have caused some resistance about QbD implementation. To show a possible solution, this work proposed a rapid process development method, which used direct analysis in real time mass spectrometry (DART-MS) as a process analytical technology (PAT) tool for studying the chromatographic process of Ginkgo biloba L., as an example. The breakthrough curves were fast determined by DART-MS at-line. A high correlation coefficient of 0.9520 was found between the concentrations of ginkgolide A determined by DART-MS and HPLC. Based on the PAT tool, the impacts of process parameters on the adsorption capacity were discovered rapidly, which showed a decreased adsorption capacity with the increase of the flow rate. This work has shown the feasibility and advantages of integrating PAT into QbD implementation for rapid process development. Copyright © 2014 Elsevier B.V. All rights reserved.

Recollection is a continuous process: implications for dual-process theories of recognition memory.

Science.gov (United States)

Mickes, Laura; Wais, Peter E; Wixted, John T

2009-04-01

Dual-process theory, which holds that recognition decisions can be based on recollection or familiarity, has long seemed incompatible with signal detection theory, which holds that recognition decisions are based on a singular, continuous memory-strength variable. Formal dual-process models typically regard familiarity as a continuous process (i.e., familiarity comes in degrees), but they construe recollection as a categorical process (i.e., recollection either occurs or does not occur). A continuous process is characterized by a graded relationship between confidence and accuracy, whereas a categorical process is characterized by a binary relationship such that high confidence is associated with high accuracy but all lower degrees of confidence are associated with chance accuracy. Using a source-memory procedure, we found that the relationship between confidence and source-recollection accuracy was graded. Because recollection, like familiarity, is a continuous process, dual-process theory is more compatible with signal detection theory than previously thought.

Fractional Poisson process (II)

International Nuclear Information System (INIS)

Wang Xiaotian; Wen Zhixiong; Zhang Shiying

2006-01-01

In this paper, we propose a stochastic process W H (t)(H-bar (12,1)) which we call fractional Poisson process. The process W H (t) is self-similar in wide sense, displays long range dependence, and has more fatter tail than Gaussian process. In addition, it converges to fractional Brownian motion in distribution

Making process improvement 'stick'.

Science.gov (United States)

Studer, Quint

2014-06-01

To sustain gains from a process improvement initiative, healthcare organizations should: Explain to staff why a process improvement initiative is needed. Encourage leaders within the organization to champion the process improvement, and tie their evaluations to its outcomes. Ensure that both leaders and employees have the skills to help sustain the sought-after process improvements.

Process Improvement Essentials

CERN Document Server

Persse, James R

2006-01-01

Process Improvement Essentials combines the foundation needed to understand process improvement theory with the best practices to help individuals implement process improvement initiatives in their organization. The three leading programs: ISO 9001:2000, CMMI, and Six Sigma--amidst the buzz and hype--tend to get lumped together under a common label. This book delivers a combined guide to all three programs, compares their applicability, and then sets the foundation for further exploration.

Integrated Renovation Process

DEFF Research Database (Denmark)

Galiotto, Nicolas; Heiselberg, Per; Knudstrup, Mary-Ann

2016-01-01

renovation to be overcome. The homeowners were better integrated and their preferences and immaterial values were better taken into account. To keep the decision-making process economically viable and timely, the process as known today still needs to be improved, and new tools need to be developed....... This paper presents a new scheme: the integrated renovation process. One successful case study is introduced, and recommendations for future developments needed in the field are provided....

Business Process Quality Computation : Computing Non-Functional Requirements to Improve Business Processes

NARCIS (Netherlands)

Heidari, F.

2015-01-01

Business process modelling is an important part of system design. When designing or redesigning a business process, stakeholders specify, negotiate, and agree on business requirements to be satisfied, including non-functional requirements that concern the quality of the business process. This thesis

Specification of e-business process model for PayPal online payment process using Reo

NARCIS (Netherlands)

M. Xie

2005-01-01

textabstractE-business process modeling allows business analysts to better understand and analyze the business processes, and eventually to use software systems to automate (parts of) these business processes to achieve higher profit. To support e-business process modeling, many business process

Honing process optimization algorithms

Science.gov (United States)

Kadyrov, Ramil R.; Charikov, Pavel N.; Pryanichnikova, Valeria V.

2018-03-01

This article considers the relevance of honing processes for creating high-quality mechanical engineering products. The features of the honing process are revealed and such important concepts as the task for optimization of honing operations, the optimal structure of the honing working cycles, stepped and stepless honing cycles, simulation of processing and its purpose are emphasized. It is noted that the reliability of the mathematical model determines the quality parameters of the honing process control. An algorithm for continuous control of the honing process is proposed. The process model reliably describes the machining of a workpiece in a sufficiently wide area and can be used to operate the CNC machine CC743.

Sustainable process synthesis–intensification

DEFF Research Database (Denmark)

Babi, Deenesh Kavi; Holtbruegge, Johannes; Lutze, Philip

2015-01-01

Chemical industry is facing global challenges such as the need to find sustainable production processes.Process intensification as part of process synthesis has the potential to find truly innovative and moresustainable solutions. In this paper, a computer-aided, multi-level, multi-scale framework...... for synthesis,design and intensification of processes, for identifying more sustainable alternatives is presented. Withinthe framework, a three stage work-flow has been implemented where, in the first “synthesis” stage anoptimal processing route is synthesized through a network superstructure optimization...

Data processing made simple

CERN Document Server

Wooldridge, Susan

2013-01-01

Data Processing: Made Simple, Second Edition presents discussions of a number of trends and developments in the world of commercial data processing. The book covers the rapid growth of micro- and mini-computers for both home and office use; word processing and the 'automated office'; the advent of distributed data processing; and the continued growth of database-oriented systems. The text also discusses modern digital computers; fundamental computer concepts; information and data processing requirements of commercial organizations; and the historical perspective of the computer industry. The

Participative Facility Planning for Obstetrical and Neonatal Care Processes: Beginning of Life Process

Directory of Open Access Journals (Sweden)

Jori Reijula

2016-01-01

Full Text Available Introduction. Old hospitals may promote inefficient patient care processes and safety. A new, functionally planned hospital presents a chance to create an environment that supports streamlined, patient-centered healthcare processes and adapts to users’ needs. This study depicts the phases of a facility planning project for pregnant women and newborn care processes (beginning of life process at Turku University Hospital. Materials and Methods. Project design reports and meeting documents were utilized to assess the beginning of life process as well as the work processes of the Women’s and Children’s Hospital. Results. The main elements of the facility design (FD project included rigorous preparation for the FD phase, functional planning throughout the FD process, and setting key values: (1 family-centered care, (2 Lean thinking and Lean tools as the framework for the FD process, (3 safety, and (4 cooperation. Conclusions. A well-prepared FD project with sufficient insight into functional planning, Lean thinking, and user-centricity seemed to facilitate the actual FD process. Although challenges occurred, the key values were not forgone and were successfully incorporated into the new hospital building.

Signals, processes, and systems an interactive multimedia introduction to signal processing

CERN Document Server

Karrenberg, Ulrich

2013-01-01

This is a very new concept for learning Signal Processing, not only from the physically-based scientific fundamentals, but also from the didactic perspective, based on modern results of brain research. The textbook together with the DVD form a learning system that provides investigative studies and enables the reader to interactively visualize even complex processes. The unique didactic concept is built on visualizing signals and processes on the one hand, and on graphical programming of signal processing systems on the other. The concept has been designed especially for microelectronics, computer technology and communication. The book allows to develop, modify, and optimize useful applications using DasyLab - a professional and globally supported software for metrology and control engineering. With the 3rd edition, the software is also suitable for 64 bit systems running on Windows 7. Real signals can be acquired, processed and played on the sound card of your computer. The book provides more than 200 pre-pr...

Modular toolkit for Data Processing (MDP: a Python data processing framework

Directory of Open Access Journals (Sweden)

Tiziano Zito

2009-01-01

Full Text Available Modular toolkit for Data Processing (MDP is a data processing framework written in Python. From the user's perspective, MDP is a collection of supervised and unsupervised learning algorithms and other data processing units that can be combined into data processing sequences and more complex feed-forward network architectures. Computations are performed efficiently in terms of speed and memory requirements. From the scientific developer's perspective, MDP is a modular framework, which can easily be expanded. The implementation of new algorithms is easy and intuitive. The new implemented units are then automatically integrated with the rest of the library. MDP has been written in the context of theoretical research in neuroscience, but it has been designed to be helpful in any context where trainable data processing algorithms are used. Its simplicity on the user's side, the variety of readily available algorithms, and the reusability of the implemented units make it also a useful educational tool.

ARTIST process. A novel chemical process for treatment of spent nuclear fuel

International Nuclear Information System (INIS)

Tachimori, Shoichi

2001-10-01

A new chemical process, ARTIST process, is proposed for the treatment of spent nuclear fuel. The main concept of the ARTIST process is to recover and stock all actinides (Ans) as two groups, uranium (U) and a mixture of transuranics (TRU), to preserve their resource value and to dispose solely fission products (FPs). The process is composed of two main steps, an U exclusive isolation and a total recovery of TRU; which copes with the nuclear non-proliferation measures, and additionally of Pu separation process and soft N-donor process if requested, and optionally of processes for separation of long-lived FPs. These An products: U-product and TRU-product, are to be solidified by calcination and allowed to the interim stockpile for future utilization. These separations are achieved by use of amidic extractants in accord with the CHON principle. The technical feasibility of the ARTIST process was explained by the performance of both the branched alkyl monoamides in extracting U and suppressing the extraction of tetravalent Ans due to the steric effect and the diglycolic amide (TODGA) in thorough extraction of all TRU by tridentate fashion. When these TRU are requested to put into reactors, LWR or FBR, for power generation or the Accelerator - Driven System (ADS) for transmutation, Pu (Np) or Am-Cm (Np) are to be extracted from the TRU-product. (author)

Exploiting process cubes, analytic workflows and process mining for business process reporting : a case study in education

NARCIS (Netherlands)

Bolt Iriondo, Alfredo; de Leoni, Massimiliano; van der Aalst, Wil M.P.; Gorissen, Pierre; Ceravolo, P.; Rinderle-Ma, S.

2015-01-01

Business Process Intelligence (BPI) is an emerging topic that has gained popularity in the last decade. It is driven by the need for analysis techniques that allow businesses to understand and improve their processes. One of the most common applications of BPI is reporting, which consists on the

On Intelligent Design and Planning Method of Process Route Based on Gun Breech Machining Process

Science.gov (United States)

Hongzhi, Zhao; Jian, Zhang

2018-03-01

The paper states an approach of intelligent design and planning of process route based on gun breech machining process, against several problems, such as complex machining process of gun breech, tedious route design and long period of its traditional unmanageable process route. Based on gun breech machining process, intelligent design and planning system of process route are developed by virtue of DEST and VC++. The system includes two functional modules--process route intelligent design and its planning. The process route intelligent design module, through the analysis of gun breech machining process, summarizes breech process knowledge so as to complete the design of knowledge base and inference engine. And then gun breech process route intelligently output. On the basis of intelligent route design module, the final process route is made, edited and managed in the process route planning module.

A systematic synthesis and design methodology to achieve process intensification in (bio) chemical processes

DEFF Research Database (Denmark)

Lutze, Philip; Roman Martinez, Alicia; Woodley, John

2012-01-01

Process intensification (PI) has the potential to improve existing processes or create new process options, which are needed in order to produce products using more sustainable methods. In principle, an enormous number of process options can be generated but where and how the process should be in...

Process Mining Methodology for Health Process Tracking Using Real-Time Indoor Location Systems

Science.gov (United States)

Fernandez-Llatas, Carlos; Lizondo, Aroa; Monton, Eduardo; Benedi, Jose-Miguel; Traver, Vicente

2015-01-01

The definition of efficient and accurate health processes in hospitals is crucial for ensuring an adequate quality of service. Knowing and improving the behavior of the surgical processes in a hospital can improve the number of patients that can be operated on using the same resources. However, the measure of this process is usually made in an obtrusive way, forcing nurses to get information and time data, affecting the proper process and generating inaccurate data due to human errors during the stressful journey of health staff in the operating theater. The use of indoor location systems can take time information about the process in an unobtrusive way, freeing nurses, allowing them to engage in purely welfare work. However, it is necessary to present these data in a understandable way for health professionals, who cannot deal with large amounts of historical localization log data. The use of process mining techniques can deal with this problem, offering an easily understandable view of the process. In this paper, we present a tool and a process mining-based methodology that, using indoor location systems, enables health staff not only to represent the process, but to know precise information about the deployment of the process in an unobtrusive and transparent way. We have successfully tested this tool in a real surgical area with 3613 patients during February, March and April of 2015. PMID:26633395

Process Mining Methodology for Health Process Tracking Using Real-Time Indoor Location Systems.

Science.gov (United States)

Fernandez-Llatas, Carlos; Lizondo, Aroa; Monton, Eduardo; Benedi, Jose-Miguel; Traver, Vicente

2015-11-30

The definition of efficient and accurate health processes in hospitals is crucial for ensuring an adequate quality of service. Knowing and improving the behavior of the surgical processes in a hospital can improve the number of patients that can be operated on using the same resources. However, the measure of this process is usually made in an obtrusive way, forcing nurses to get information and time data, affecting the proper process and generating inaccurate data due to human errors during the stressful journey of health staff in the operating theater. The use of indoor location systems can take time information about the process in an unobtrusive way, freeing nurses, allowing them to engage in purely welfare work. However, it is necessary to present these data in a understandable way for health professionals, who cannot deal with large amounts of historical localization log data. The use of process mining techniques can deal with this problem, offering an easily understandable view of the process. In this paper, we present a tool and a process mining-based methodology that, using indoor location systems, enables health staff not only to represent the process, but to know precise information about the deployment of the process in an unobtrusive and transparent way. We have successfully tested this tool in a real surgical area with 3613 patients during February, March and April of 2015.

Discovering Process Reference Models from Process Variants Using Clustering Techniques

NARCIS (Netherlands)

Li, C.; Reichert, M.U.; Wombacher, Andreas

2008-01-01

In today's dynamic business world, success of an enterprise increasingly depends on its ability to react to changes in a quick and flexible way. In response to this need, process-aware information systems (PAIS) emerged, which support the modeling, orchestration and monitoring of business processes

Thin film processes II

CERN Document Server

Kern, Werner

1991-01-01

This sequel to the 1978 classic, Thin Film Processes, gives a clear, practical exposition of important thin film deposition and etching processes that have not yet been adequately reviewed. It discusses selected processes in tutorial overviews with implementation guide lines and an introduction to the literature. Though edited to stand alone, when taken together, Thin Film Processes II and its predecessor present a thorough grounding in modern thin film techniques.Key Features* Provides an all-new sequel to the 1978 classic, Thin Film Processes* Introduces new topics, and sever

Business process transformation

CERN Document Server

Grover, Varun

2015-01-01

Featuring contributions from prominent thinkers and researchers, this volume in the ""Advances in Management Information Systems"" series provides a rich set of conceptual, empirical, and introspective studies that epitomize fundamental knowledge in the area of Business Process Transformation. Processes are interpreted broadly to include operational and managerial processes within and between organizations, as well as those involved in knowledge generation. Transformation includes radical and incremental change, its conduct, management, and outcome. The editors and contributing authors pay clo

Shell coal gasification process

Energy Technology Data Exchange (ETDEWEB)

Hennekes, B. [Shell Global Solutions (US) Inc. (United States). Technology Marketing

2002-07-01

The presentation, on which 17 slides/overheads are included in the papers, explained the principles of the Shell coal gasification process and the methods incorporated for control of sulfur dioxide, nitrogen oxides, particulates and mercury. The economics of the process were discussed. The differences between gasification and burning, and the differences between the Shell process and other processes were discussed.

Closed-Loop Process Control for Electron Beam Freeform Fabrication and Deposition Processes

Science.gov (United States)

Taminger, Karen M. (Inventor); Hafley, Robert A. (Inventor); Martin, Richard E. (Inventor); Hofmeister, William H. (Inventor)

2013-01-01

A closed-loop control method for an electron beam freeform fabrication (EBF(sup 3)) process includes detecting a feature of interest during the process using a sensor(s), continuously evaluating the feature of interest to determine, in real time, a change occurring therein, and automatically modifying control parameters to control the EBF(sup 3) process. An apparatus provides closed-loop control method of the process, and includes an electron gun for generating an electron beam, a wire feeder for feeding a wire toward a substrate, wherein the wire is melted and progressively deposited in layers onto the substrate, a sensor(s), and a host machine. The sensor(s) measure the feature of interest during the process, and the host machine continuously evaluates the feature of interest to determine, in real time, a change occurring therein. The host machine automatically modifies control parameters to the EBF(sup 3) apparatus to control the EBF(sup 3) process in a closed-loop manner.

Issues Management Process Course # 38401

Energy Technology Data Exchange (ETDEWEB)

Binion, Ula Marie [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2018-02-01

The purpose of this training it to advise Issues Management Coordinators (IMCs) on the revised Contractor Assurance System (CAS) Issues Management (IM) process. Terminal Objectives: Understand the Laboratory’s IM process; Understand your role in the Laboratory’s IM process. Learning Objectives: Describe the IM process within the context of the CAS; Describe the importance of implementing an institutional IM process at LANL; Describe the process flow for the Laboratory’s IM process; Apply the definition of an issue; Use available resources to determine initial screening risk levels for issues; Describe the required major process steps for each risk level; Describe the personnel responsibilities for IM process implementation; Access available resources to support IM process implementation.

Organizing Process

DEFF Research Database (Denmark)

Hull Kristensen, Peer; Bojesen, Anders

This paper invites to discuss the processes of individualization and organizing being carried out under what we might see as an emerging regime of change. The underlying argumentation is that in certain processes of change, competence becomes questionable at all times. The hazy characteristics...... of this regime of change are pursued through a discussion of competencies as opposed to qualifications illustrated by distinct cases from the Danish public sector in the search for repetitive mechanisms. The cases are put into a general perspective by drawing upon experiences from similar change processes...... in MNCs. The paper concludes by asking whether we can escape from a regime of competence in a world defined by a rhetoric of change and create a more promising world in which doubt and search serve as a strategy for gaining knowledge and professionalism that improve on our capability for mutualism....

The SILVA atomic process

International Nuclear Information System (INIS)

Cazalet, J.

1997-01-01

The SILVA laser isotope separation process is based on the laser selective photo-ionization of uranium atomic vapour; the process is presently under development by CEA and COGEMA in France, with the aim to reduce by a factor three the cost of uranium enrichment. The two main components of a SILVA process plant are the lasers (copper vapour lasers and dye lasers) and the separator for the vaporization (with a high energy electron beam), ionization and separation operations. Researches on the SILVA process started in 1985 and the technical and economical feasibility is to be demonstrated in 1997. The progresses of similar rival processes and other processes are discussed and the remaining research stages and themes of the SILVA program are presented

Badge Office Process Analysis

Energy Technology Data Exchange (ETDEWEB)

Haurykiewicz, John Paul [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Dinehart, Timothy Grant [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Parker, Robert Young [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-05-12

The purpose of this process analysis was to analyze the Badge Offices’ current processes from a systems perspective and consider ways of pursuing objectives set forth by SEC-PS, namely increased customer flow (throughput) and reduced customer wait times. Information for the analysis was gathered for the project primarily through Badge Office Subject Matter Experts (SMEs), and in-person observation of prevailing processes. Using the information gathered, a process simulation model was constructed to represent current operations and allow assessment of potential process changes relative to factors mentioned previously. The overall purpose of the analysis was to provide SEC-PS management with information and recommendations to serve as a basis for additional focused study and areas for potential process improvements in the future.

Water And Waste Water Processing

International Nuclear Information System (INIS)

Yang, Byeong Ju

1988-04-01

This book shows US the distribution diagram of water and waste water processing with device of water processing, and device of waste water processing, property of water quality like measurement of pollution of waste water, theoretical Oxygen demand, and chemical Oxygen demand, processing speed like zero-order reactions and enzyme reactions, physical processing of water and waste water, chemical processing of water and waste water like neutralization and buffering effect, biological processing of waste water, ammonia removal, and sludges processing.

Specification of e-business process model for PayPal online payment process using Reo

OpenAIRE

Xie, M.

2005-01-01

textabstractE-business process modeling allows business analysts to better understand and analyze the business processes, and eventually to use software systems to automate (parts of) these business processes to achieve higher profit. To support e-business process modeling, many business process modeling languages have been used as tools. However, many existing business process modeling languages lack (a) formal semantics, (b) formal computational model, and (c) an integrated view of the busi...

Translating Message Sequence Charts to other Process Languages using Process

DEFF Research Database (Denmark)

Lassen, Kristian Bisgaard; van Dongen, Boudewijn F.

2008-01-01

stakeholders. Often such discussions lead to more complete behavioral models described by e.g. Event-driven Process Chains (EPCs), UML activity diagrams, BPMN models, Petri nets, etc. Process mining on the other hand, deals with the problem of constructing complete behavioral models by analyzing event logs...

Pennsylvania's partnering process

International Nuclear Information System (INIS)

Latham, J.W.

1996-01-01

Pennsylvania is committed to finding a site for a low-level radioactive waste (LLRW) disposal facility through an innovative voluntary process. The Pennsylvania Department of Environmental Protection (DEP) and Chem-Nuclear Systems, Inc. (CNSI) developed the Community Partnering Plan with extensive public participation. The Community Partnering Plan outlines a voluntary process that empowers municipalities to evaluate the advantages and disadvantages of hosting the facility. DEP and CNSI began developing the Community Partnering Plan in July 1995. Before then, CNSI was using a screening process prescribed by state law and regulations to find a location for the facility. So far, approximately 78 percent of the Commonwealth has been identified as disqualified as a site for the LLRW disposal facility. The siting effort will now focus on identifying volunteer host municipalities in the remaining 22 percent of the state. This combination of technical screening and voluntary consideration makes Pennsylvania's process unique. A volunteered site will have to meet the same tough requirements for protecting people and the environment as a site chosen through the screening process. Protection of public health and safety continues to be the foundation of the state's siting efforts. The Community Partnering Plan offers a window of opportunity. If Pennsylvania does not find volunteer municipalities with suitable sites by the end of 1997, it probably will return to a technical screening process

Raw material changes and their processing parameters in an extrusion cooking process

DEFF Research Database (Denmark)

Cheng, Hongyuan; Friis, Alan

In this work, the effects of raw material and process parameters on product expansion in a fish feed extrusion process were investigated. Four different recipes were studied with a pilot-scale twin-screw co-rotating extruder according to a set of pre-defined processing conditions. In the four rec...

Process monitoring for intelligent manufacturing processes - Methodology and application to Robot Assisted Polishing

DEFF Research Database (Denmark)

Pilny, Lukas

Process monitoring provides important information on the product, process and manufacturing system during part manufacturing. Such information can be used for process optimization and detection of undesired processing conditions to initiate timely actions for avoidance of defects, thereby improving...... quality assurance. This thesis is aimed at a systematic development of process monitoring solutions, constituting a key element of intelligent manufacturing systems towards zero defect manufacturing. A methodological approach of general applicability is presented in this concern.The approach consists...... of six consecutive steps for identification of product Vital Quality Characteristics (VQCs) and Key Process Variables (KPVs), selection and characterization of sensors, optimization of sensors placement, validation of the monitoring solutions, definition of the reference manufacturing performance...

Laser dimpling process parameters selection and optimization using surrogate-driven process capability space

Science.gov (United States)

Ozkat, Erkan Caner; Franciosa, Pasquale; Ceglarek, Dariusz

2017-08-01

Remote laser welding technology offers opportunities for high production throughput at a competitive cost. However, the remote laser welding process of zinc-coated sheet metal parts in lap joint configuration poses a challenge due to the difference between the melting temperature of the steel (∼1500 °C) and the vapourizing temperature of the zinc (∼907 °C). In fact, the zinc layer at the faying surface is vapourized and the vapour might be trapped within the melting pool leading to weld defects. Various solutions have been proposed to overcome this problem over the years. Among them, laser dimpling has been adopted by manufacturers because of its flexibility and effectiveness along with its cost advantages. In essence, the dimple works as a spacer between the two sheets in lap joint and allows the zinc vapour escape during welding process, thereby preventing weld defects. However, there is a lack of comprehensive characterization of dimpling process for effective implementation in real manufacturing system taking into consideration inherent changes in variability of process parameters. This paper introduces a methodology to develop (i) surrogate model for dimpling process characterization considering multiple-inputs (i.e. key control characteristics) and multiple-outputs (i.e. key performance indicators) system by conducting physical experimentation and using multivariate adaptive regression splines; (ii) process capability space (Cp-Space) based on the developed surrogate model that allows the estimation of a desired process fallout rate in the case of violation of process requirements in the presence of stochastic variation; and, (iii) selection and optimization of the process parameters based on the process capability space. The proposed methodology provides a unique capability to: (i) simulate the effect of process variation as generated by manufacturing process; (ii) model quality requirements with multiple and coupled quality requirements; and (iii

Contaminated nickel scrap processing

International Nuclear Information System (INIS)

Compere, A.L.; Griffith, W.L.; Hayden, H.W.; Johnson, J.S. Jr.; Wilson, D.F.

1994-12-01

The DOE will soon choose between treating contaminated nickel scrap as a legacy waste and developing high-volume nickel decontamination processes. In addition to reducing the volume of legacy wastes, a decontamination process could make 200,000 tons of this strategic metal available for domestic use. Contaminants in DOE nickel scrap include 234 Th, 234 Pa, 137 Cs, 239 Pu (trace), 60 Co, U, 99 Tc, and 237 Np (trace). This report reviews several industrial-scale processes -- electrorefining, electrowinning, vapormetallurgy, and leaching -- used for the purification of nickel. Conventional nickel electrolysis processes are particularly attractive because they use side-stream purification of process solutions to improve the purity of nickel metal. Additionally, nickel purification by electrolysis is effective in a variety of electrolyte systems, including sulfate, chloride, and nitrate. Conventional electrorefining processes typically use a mixed electrolyte which includes sulfate, chloride, and borate. The use of an electrorefining or electrowinning system for scrap nickel recovery could be combined effectively with a variety of processes, including cementation, solvent extraction, ion exchange, complex-formation, and surface sorption, developed for uranium and transuranic purification. Selected processes were reviewed and evaluated for use in nickel side-stream purification. 80 refs

Wetland Groundwater Processes

National Research Council Canada - National Science Library

Williams, Greg

1993-01-01

This technical note summarizes hydrologic and hydraulic (H AND H) processes and the related terminology that will likely be encountered during an evaluation of the effect of ground-water processes on wetland function...

Manufacturing Process Selection of Composite Bicycle’s Crank Arm using Analytical Hierarchy Process (AHP)

Science.gov (United States)

Luqman, M.; Rosli, M. U.; Khor, C. Y.; Zambree, Shayfull; Jahidi, H.

2018-03-01

Crank arm is one of the important parts in a bicycle that is an expensive product due to the high cost of material and production process. This research is aimed to investigate the potential type of manufacturing process to fabricate composite bicycle crank arm and to describe an approach based on analytical hierarchy process (AHP) that assists decision makers or manufacturing engineers in determining the most suitable process to be employed in manufacturing of composite bicycle crank arm at the early stage of the product development process to reduce the production cost. There are four types of processes were considered, namely resin transfer molding (RTM), compression molding (CM), vacuum bag molding and filament winding (FW). The analysis ranks these four types of process for its suitability in the manufacturing of bicycle crank arm based on five main selection factors and 10 sub factors. Determining the right manufacturing process was performed based on AHP process steps. Consistency test was performed to make sure the judgements are consistent during the comparison. The results indicated that the compression molding was the most appropriate manufacturing process because it has the highest value (33.6%) among the other manufacturing processes.

Advanced materials processing

International Nuclear Information System (INIS)

Giamei, A.F.

1993-01-01

Advanced materials will require improved processing methods due to high melting points, low toughness or ductility values, high reactivity with air or ceramics and typically complex crystal structures with significant anisotropy in flow and/or fracture stress. Materials for structural applications at elevated temperature in critical systems will require processing with a high degree of control. This requires an improved understanding of the relationship between process variables and microstructure to enable control systems to achieve consistently high quality. One avenue to the required level of understanding is computer simulation. Past attempts to do process modeling have been hampered by incomplete data regarding thermophysical or mechanical material behavior. Some of the required data can be calculated. Due to the advances in software and hardware, accuracy and costs are in the realm of acquiring experimental data. Such calculations can, for example, be done at an atomic level to compute lattice energy, fault energies, density of states and charge densities. These can lead to fundamental information about the competition between slip and fracture, anisotropy of bond strength (and therefore cleavage strength), cohesive strength, adhesive strength, elastic modulus, thermal expansion and possibly other quantities which are difficult (and therefore expensive to measure). Some of these quantities can be fed into a process model. It is probable that temperature dependencies can be derived numerically as well. Examples are given of the beginnings of such an approach for Ni 3 Al and MoSi 2 . Solidification problems are examples of the state-of-the-art process modeling and adequately demonstrate the need for extensive input data. Such processes can be monitored in terms of interfacial position vs. time, cooling rate and thermal gradient

Optimization of a novel enzyme treatment process for early-stage processing of sheepskins.

Science.gov (United States)

Lim, Y F; Bronlund, J E; Allsop, T F; Shilton, A N; Edmonds, R L

2010-01-01

An enzyme treatment process for early-stage processing of sheepskins has been previously reported by the Leather and Shoe Research Association of New Zealand (LASRA) as an alternative to current industry operations. The newly developed process had marked benefits over conventional processing in terms of a lowered energy usage (73%), processing time (47%) as well as water use (49%), but had been developed as a "proof of principle''. The objective of this work was to develop the process further to a stage ready for adoption by industry. Mass balancing was used to investigate potential modifications for the process based on the understanding developed from a detailed analysis of preliminary design trials. Results showed that a configuration utilising a 2 stage counter-current system for the washing stages and segregation and recycling of enzyme float prior to dilution in the neutralization stage was a significant improvement. Benefits over conventional processing include a reduction of residual TDS by 50% at the washing stages and 70% savings on water use overall. Benefits over the un-optimized LASRA process are reduction of solids in product after enzyme treatment and neutralization stages by 30%, additional water savings of 21%, as well as 10% savings of enzyme usage.

Rational Unified Process

OpenAIRE

Kopal, Nils

2016-01-01

In this German seminar paper, which was written in the year 2011 at the University of Duisburg for a Bachelor Colloquium in Applied computer science, we show a brief overview of the Rational Unified Process (RUP). Thus, interested students or generally interested people in software development gain a first impression of RUP. The paper includes a survey and overview of the underlying process structure, the phases of the process, its workflows, and describes the always by the RUP developers pos...

gProcess and ESIP Platforms for Satellite Imagery Processing over the Grid

Science.gov (United States)

Bacu, Victor; Gorgan, Dorian; Rodila, Denisa; Pop, Florin; Neagu, Gabriel; Petcu, Dana

2010-05-01

The Environment oriented Satellite Data Processing Platform (ESIP) is developed through the SEE-GRID-SCI (SEE-GRID eInfrastructure for regional eScience) co-funded by the European Commission through FP7 [1]. The gProcess Platform [2] is a set of tools and services supporting the development and the execution over the Grid of the workflow based processing, and particularly the satelite imagery processing. The ESIP [3], [4] is build on top of the gProcess platform by adding a set of satellite image processing software modules and meteorological algorithms. The satellite images can reveal and supply important information on earth surface parameters, climate data, pollution level, weather conditions that can be used in different research areas. Generally, the processing algorithms of the satellite images can be decomposed in a set of modules that forms a graph representation of the processing workflow. Two types of workflows can be defined in the gProcess platform: abstract workflow (PDG - Process Description Graph), in which the user defines conceptually the algorithm, and instantiated workflow (iPDG - instantiated PDG), which is the mapping of the PDG pattern on particular satellite image and meteorological data [5]. The gProcess platform allows the definition of complex workflows by combining data resources, operators, services and sub-graphs. The gProcess platform is developed for the gLite middleware that is available in EGEE and SEE-GRID infrastructures [6]. gProcess exposes the specific functionality through web services [7]. The Editor Web Service retrieves information on available resources that are used to develop complex workflows (available operators, sub-graphs, services, supported resources, etc.). The Manager Web Service deals with resources management (uploading new resources such as workflows, operators, services, data, etc.) and in addition retrieves information on workflows. The Executor Web Service manages the execution of the instantiated workflows

Business Process Inventory

Data.gov (United States)

Office of Personnel Management — Inventory of maps and descriptions of the business processes of the U.S. Office of Personnel Management (OPM), with an emphasis on the processes of the Office of the...

Eye Tracking Meets the Process of Process Modeling: a Visual Analytic Approach

DEFF Research Database (Denmark)

Burattin, Andrea; Kaiser, M.; Neurauter, Manuel

2017-01-01

Research on the process of process modeling (PPM) studies how process models are created. It typically uses the logs of the interactions with the modeling tool to assess the modeler’s behavior. In this paper we suggest to introduce an additional stream of data (i.e., eye tracking) to improve the ...

Empirical evaluation of the Process Overview Measure for assessing situation awareness in process plants.

Science.gov (United States)

Lau, Nathan; Jamieson, Greg A; Skraaning, Gyrd

2016-03-01

The Process Overview Measure is a query-based measure developed to assess operator situation awareness (SA) from monitoring process plants. A companion paper describes how the measure has been developed according to process plant properties and operator cognitive work. The Process Overview Measure demonstrated practicality, sensitivity, validity and reliability in two full-scope simulator experiments investigating dramatically different operational concepts. Practicality was assessed based on qualitative feedback of participants and researchers. The Process Overview Measure demonstrated sensitivity and validity by revealing significant effects of experimental manipulations that corroborated with other empirical results. The measure also demonstrated adequate inter-rater reliability and practicality for measuring SA in full-scope simulator settings based on data collected on process experts. Thus, full-scope simulator studies can employ the Process Overview Measure to reveal the impact of new control room technology and operational concepts on monitoring process plants. Practitioner Summary: The Process Overview Measure is a query-based measure that demonstrated practicality, sensitivity, validity and reliability for assessing operator situation awareness (SA) from monitoring process plants in representative settings.

Technology or Process First?

DEFF Research Database (Denmark)

Siurdyban, Artur Henryk; Svejvig, Per; Møller, Charles

Enterprise Systems Management (ESM) and Business Pro- cess Management (BPM), although highly correlated, have evolved as alternative and mutually exclusive approaches to corporate infrastruc- ture. As a result, companies struggle to nd the right balance between technology and process factors...... in infrastructure implementation projects. The purpose of this paper is articulate a need and a direction to medi- ate between the process-driven and the technology-driven approaches. Using a cross-case analysis, we gain insight into two examples of sys- tems and process implementation. We highlight the dierences...... between them using strategic alignment, Enterprise Systems and Business Process Management theories. We argue that the insights from these cases can lead to a better alignment between process and technology. Implications for practice include the direction towards a closer integration of process...

Sustainable Process Synthesis-Intensification

DEFF Research Database (Denmark)

Babi, Deenesh Kavi

The chemical and biochemical industry needs major reductions in energy consumption, waste generation, number of equipment used in the construction of plants and capital/operational cost. These required reductions can be addressed through process intensification that is the efficient use of raw....... Therefore sustainable process design can be achieved by performing process syn-thesis and process intensification together. The main contribution of this work is the development of a systematic computer-aided multi-scale, multi-level framework for performing process synthesis-intensification that aims...... designs that otherwise could not be found from the higher scales. The framework is applied to three case studies related to the chemical and bioprocess industry in order to test the applicability of the framework for covering a wide range of applications, showing that process intensification provides...

Remarks to a process-overlapping description of cost structures of energy conversion processes

International Nuclear Information System (INIS)

Barnert, H.

1986-03-01

The cost of energy conversion processes are more and more determined by capital expenses. These are partly used to improve the efficiency. With a mathematical formula for the relation between capital costs and efficiency a process-over-laping description is proposed and proved at 10 typically chosen energy conversion processes. The result is a classification of enery conversion processes in categories of efficiency-producing and efficiency-independent capital expenditures. Another result is that process-overlapping the relative capital cost supplement is described by the (1-eta)/eta-law. (orig.) [de

Renewal processes

CERN Document Server

Mitov, Kosto V

2014-01-01

This monograph serves as an introductory text to classical renewal theory and some of its applications for graduate students and researchers in mathematics and probability theory. Renewal processes play an important part in modeling many phenomena in insurance, finance, queuing systems, inventory control and other areas. In this book, an overview of univariate renewal theory is given and renewal processes in the non-lattice and lattice case are discussed. A pre-requisite is a basic knowledge of probability theory.

Transnational Learning Processes

DEFF Research Database (Denmark)

Nedergaard, Peter

This paper analyses and compares the transnational learning processes in the employment field in the European Union and among the Nordic countries. Based theoretically on a social constructivist model of learning and methodologically on a questionnaire distributed to the relevant participants......, a number of hypotheses concerning transnational learning processes are tested. The paper closes with a number of suggestions regarding an optimal institutional setting for facilitating transnational learning processes.Key words: Transnational learning, Open Method of Coordination, Learning, Employment......, European Employment Strategy, European Union, Nordic countries....

Software Process Validation: Quantitatively Measuring the Correspondence of a Process to a Model

National Research Council Canada - National Science Library

Cook, Jonathan E; Wolf, Alexander L

1997-01-01

.... When process models and process executions diverge, something significant is happening. The authors have developed techniques for uncovering and measuring the discrepancies between models and executions, which they call process validation...

A computer-aided approach for achieving sustainable process design by process intensification

DEFF Research Database (Denmark)

Anantasarn, Nateetorn; Suriyapraphadilok, Uthaiporn; Babi, Deenesh Kavi

2017-01-01

to generate flowsheet alternatives that satisfy the design targets thereby, minimizing and/or eliminating the process hot-spots. The application of the framework is highlighted through the production of para-xylene via toluene methylation where more sustainable flowsheet alternatives that consist of hybrid......Process intensification can be applied to achieve sustainable process design. In this paper, a systematic, 3-stage synthesis-intensification framework is applied to achieve more sustainable design. In stage 1, the synthesis stage, an objective function and design constraints are defined and a base...... case is synthesized. In stage 2, the design and analysis stage, the base case is analyzed using economic and environmental analyses to identify process hot-spots that are translated into design targets. In stage 3, the innovation design stage, phenomena-based process intensification is performed...

Laser material processing

CERN Document Server

Steen, William

2010-01-01

This text moves from the basics of laser physics to detailed treatments of all major materials processing techniques for which lasers are now essential. New chapters cover laser physics, drilling, micro- and nanomanufacturing and biomedical laser processing.

Cascading activation from lexical processing to letter-level processing in written word production.

Science.gov (United States)

Buchwald, Adam; Falconer, Carolyn

2014-01-01

Descriptions of language production have identified processes involved in producing language and the presence and type of interaction among those processes. In the case of spoken language production, consensus has emerged that there is interaction among lexical selection processes and phoneme-level processing. This issue has received less attention in written language production. In this paper, we present a novel analysis of the writing-to-dictation performance of an individual with acquired dysgraphia revealing cascading activation from lexical processing to letter-level processing. The individual produced frequent lexical-semantic errors (e.g., chipmunk → SQUIRREL) as well as letter errors (e.g., inhibit → INBHITI) and had a profile consistent with impairment affecting both lexical processing and letter-level processing. The presence of cascading activation is suggested by lower letter accuracy on words that are more weakly activated during lexical selection than on those that are more strongly activated. We operationalize weakly activated lexemes as those lexemes that are produced as lexical-semantic errors (e.g., lethal in deadly → LETAHL) compared to strongly activated lexemes where the intended target word (e.g., lethal) is the lexeme selected for production.

Explicit and Implicit Processes Constitute the Fast and Slow Processes of Sensorimotor Learning.

Science.gov (United States)

McDougle, Samuel D; Bond, Krista M; Taylor, Jordan A

2015-07-01

A popular model of human sensorimotor learning suggests that a fast process and a slow process work in parallel to produce the canonical learning curve (Smith et al., 2006). Recent evidence supports the subdivision of sensorimotor learning into explicit and implicit processes that simultaneously subserve task performance (Taylor et al., 2014). We set out to test whether these two accounts of learning processes are homologous. Using a recently developed method to assay explicit and implicit learning directly in a sensorimotor task, along with a computational modeling analysis, we show that the fast process closely resembles explicit learning and the slow process approximates implicit learning. In addition, we provide evidence for a subdivision of the slow/implicit process into distinct manifestations of motor memory. We conclude that the two-state model of motor learning is a close approximation of sensorimotor learning, but it is unable to describe adequately the various implicit learning operations that forge the learning curve. Our results suggest that a wider net be cast in the search for the putative psychological mechanisms and neural substrates underlying the multiplicity of processes involved in motor learning. Copyright © 2015 the authors 0270-6474/15/359568-12$15.00/0.

Contaminated nickel scrap processing

Energy Technology Data Exchange (ETDEWEB)

Compere, A.L.; Griffith, W.L.; Hayden, H.W.; Johnson, J.S. Jr.; Wilson, D.F.

1994-12-01

The DOE will soon choose between treating contaminated nickel scrap as a legacy waste and developing high-volume nickel decontamination processes. In addition to reducing the volume of legacy wastes, a decontamination process could make 200,000 tons of this strategic metal available for domestic use. Contaminants in DOE nickel scrap include {sup 234}Th, {sup 234}Pa, {sup 137}Cs, {sup 239}Pu (trace), {sup 60}Co, U, {sup 99}Tc, and {sup 237}Np (trace). This report reviews several industrial-scale processes -- electrorefining, electrowinning, vapormetallurgy, and leaching -- used for the purification of nickel. Conventional nickel electrolysis processes are particularly attractive because they use side-stream purification of process solutions to improve the purity of nickel metal. Additionally, nickel purification by electrolysis is effective in a variety of electrolyte systems, including sulfate, chloride, and nitrate. Conventional electrorefining processes typically use a mixed electrolyte which includes sulfate, chloride, and borate. The use of an electrorefining or electrowinning system for scrap nickel recovery could be combined effectively with a variety of processes, including cementation, solvent extraction, ion exchange, complex-formation, and surface sorption, developed for uranium and transuranic purification. Selected processes were reviewed and evaluated for use in nickel side-stream purification. 80 refs.

Business Process Reengineering: A Primer for the Marine Corps' Process Owner

National Research Council Canada - National Science Library

Brewster, Rollin

1997-01-01

.... Business Process Reengineering (BPR) is a technique used by the private sector to achieve order of magnitude improvements in organizational performance by leveraging information technology to enable the holistic redesign of business processes...

States in Process Calculi

Directory of Open Access Journals (Sweden)

Christoph Wagner

2014-08-01

Full Text Available Formal reasoning about distributed algorithms (like Consensus typically requires to analyze global states in a traditional state-based style. This is in contrast to the traditional action-based reasoning of process calculi. Nevertheless, we use domain-specific variants of the latter, as they are convenient modeling languages in which the local code of processes can be programmed explicitly, with the local state information usually managed via parameter lists of process constants. However, domain-specific process calculi are often equipped with (unlabeled reduction semantics, building upon a rich and convenient notion of structural congruence. Unfortunately, the price for this convenience is that the analysis is cumbersome: the set of reachable states is modulo structural congruence, and the processes' state information is very hard to identify. We extract from congruence classes of reachable states individual state-informative representatives that we supply with a proper formal semantics. As a result, we can now freely switch between the process calculus terms and their representatives, and we can use the stateful representatives to perform assertional reasoning on process calculus models.

Multi-Wave Mixing Processes

CERN Document Server

Zhang, Yanpeng

2009-01-01

"Multi-Wave Mixing Processes - From Ultrafast Polarization Beats to Electromagnetically Induced Transparency" discusses the interactions of efficient multi-wave mixing (MWM) processes enhanced by atomic coherence in multilevel atomic systems. It covers topics in five major areas: attosecond and femtosecond polarization beats of four-wave mixing (FWM) processes; heterodyne detection of FWM, six-wave mixing (SWM) and eight-wave mixing (EWM) processes; Raman and Rayleigh enhanced polarization beats; coexistence and interactions of MWM processes via electromagnetically induced transparency(EIT); multi-dressing MWM processes. The book is intended for researchers, advanced undergraduate and graduate students in Nonlinear Optics. Dr. Yanpeng Zhang is a professor at the Key Laboratory for Physical Electronics and Devices of the Ministry of Education, Xi'an Jiaotong University. Dr. Min Xiao is a professor of Physics at University of Arkansas, Fayetteville, U.S.A.

Sociotechnical design processes and working environment: The case of a continuous process wok

DEFF Research Database (Denmark)

Broberg, Ole

2000-01-01

A five-year design process of a continuous process wok has been studied with the aim of elucidating the conditions for integrating working environment aspects. The design process is seen as a network building activity and as a social shaping process of the artefact. A working environment log...... is suggested as a tool designers can use to integrate considerations of future operators' working environment....

Example process hazard analysis of a Department of Energy water chlorination process

Energy Technology Data Exchange (ETDEWEB)

1993-09-01

On February 24, 1992, the Occupational Safety and Health Administration (OSHA) released a revised version of Section 29 Code of Federal Regulations CFR Part 1910 that added Section 1910.119, entitled ``Process Safety Management of Highly Hazardous Chemicals`` (the PSM Rule). Because US Department of Energy (DOE) Orders 5480.4 and 5483.1A prescribe OSHA 29 CFR 1910 as a standard in DOE, the PSM Rule is mandatory in the DOE complex. A major element in the PSM Rule is the process hazard analysis (PrHA), which is required for all chemical processes covered by the PSM Rule. The PrHA element of the PSM Rule requires the selection and application of appropriate hazard analysis methods to systematically identify hazards and potential accident scenarios associated with processes involving highly hazardous chemicals (HHCs). The analysis in this report is an example PrHA performed to meet the requirements of the PSM Rule. The PrHA method used in this example is the hazard and operability (HAZOP) study, and the process studied is the new Hanford 300-Area Water Treatment Facility chlorination process, which is currently in the design stage. The HAZOP study was conducted on May 18--21, 1993, by a team from the Westinghouse Hanford Company (WHC), Battelle-Columbus, the DOE, and Pacific Northwest Laboratory (PNL). The chlorination process was chosen as the example process because it is common to many DOE sites, and because quantities of chlorine at those sites generally exceed the OSHA threshold quantities (TQs).

Study for process and equipment design of wet gelation stages in vibropacking process

International Nuclear Information System (INIS)

Tanimoto, Ryoji; Kikuchi, Toshiaki; Tanaka, Hirokazu; Amino, Masaki; Yanai, Minoru

2004-02-01

Process and layout design of external wet gelation stages in vibropacking process was examined for the feasibility study of commercialized FBR cycle system. In this study, following process stages for the oxide core fuel production line were covered, that is, solidification, washing, drying, calcination, reduction, sintering stages including interim storage of sintering particles and reagent recovery stage. The main results obtained by this study are as follows: (1) Based on the process examination results conducted previously, process-flow, mass-balance and number of production line/equipment were clarified. The process is covered from the receive tank of feed solution to the interim storage equipment. Reagent recovery process-flow, mass-balance were also clarified. And preliminary design of the main equipment was reexamined. (2) Normal operation procedure and the procedure after process failure were summarized along with a remote automated operation procedure. Operation sequence of each production line was mapped out by using a time-chart. (3) Design outline of reagent recovery equipments, installed to recover waste liquid from the wet gelation stages in the view of environmental impact were examined. Effective techniques such as collection of solvent, residue waste treatment method were examined its applicability and selected. Schematic block diagram was presented. (4) Analytical items and analyzing apparatus were extracted taking into account of quality control and process management. Analytical sample taking position and frequency of sampling were also examined. (5) A schematic layout drawing of main manufacturing process and reagent recovery process was presented taking into account of material handling. (6) A feature of the operating rate at each process stage was examined by analyzing failure rate reliability of each component. applying the reliability-centred method. (RCM), the operating rate was evaluated and annual maintenance period was estimated using

Semi-Markov processes

CERN Document Server

Grabski

2014-01-01

Semi-Markov Processes: Applications in System Reliability and Maintenance is a modern view of discrete state space and continuous time semi-Markov processes and their applications in reliability and maintenance. The book explains how to construct semi-Markov models and discusses the different reliability parameters and characteristics that can be obtained from those models. The book is a useful resource for mathematicians, engineering practitioners, and PhD and MSc students who want to understand the basic concepts and results of semi-Markov process theory. Clearly defines the properties and

A Petri Net-Based Software Process Model for Developing Process-Oriented Information Systems

Science.gov (United States)

Li, Yu; Oberweis, Andreas

Aiming at increasing flexibility, efficiency, effectiveness, and transparency of information processing and resource deployment in organizations to ensure customer satisfaction and high quality of products and services, process-oriented information systems (POIS) represent a promising realization form of computerized business information systems. Due to the complexity of POIS, explicit and specialized software process models are required to guide POIS development. In this chapter we characterize POIS with an architecture framework and present a Petri net-based software process model tailored for POIS development with consideration of organizational roles. As integrated parts of the software process model, we also introduce XML nets, a variant of high-level Petri nets as basic methodology for business processes modeling, and an XML net-based software toolset providing comprehensive functionalities for POIS development.

CMOS/SOS processing

Science.gov (United States)

Ramondetta, P.

1980-01-01

Report describes processes used in making complementary - metal - oxide - semiconductor/silicon-on-sapphire (CMOS/SOS) integrated circuits. Report lists processing steps ranging from initial preparation of sapphire wafers to final mapping of "good" and "bad" circuits on a wafer.

Generating process model collections

NARCIS (Netherlands)

Yan, Z.; Dijkman, R.M.; Grefen, P.W.P.J.

2017-01-01

Business process management plays an important role in the management of organizations. More and more organizations describe their operations as business processes. It is common for organizations to have collections of thousands of business processes, but for reasons of confidentiality these

Mining processes in dentistry

NARCIS (Netherlands)

Mans, R.S.; Reijers, H.A.; van Genuchten, M.; Wismeijer, D.

2012-01-01

Business processes in dentistry are quickly evolving towards "digital dentistry". This means that many steps in the dental process will increasingly deal with computerized information or computerized half products. A complicating factor in the improvement of process performance in dentistry,

Process based analysis of manually controlled drilling processes for bone

Science.gov (United States)

Teicher, Uwe; Achour, Anas Ben; Nestler, Andreas; Brosius, Alexander; Lauer, Günter

2018-05-01

The machining operation drilling is part of the standard repertoire for medical applications. This machining cycle, which is usually a multi-stage process, generates the geometric element for the subsequent integration of implants, which are screwed into the bone in subsequent processes. In addition to the form, shape and position of the generated drill hole, it is also necessary to use a technology that ensures an operation with minimal damage. A surface damaged by excessive mechanical and thermal energy input shows a deterioration in the healing capacity of implants and represents a structure with complications for inflammatory reactions. The resulting loads are influenced by the material properties of the bone, the used technology and the tool properties. An important aspect of the process analysis is the fact that machining of bone is in most of the cases a manual process that depends mainly on the skills of the operator. This includes, among other things, the machining time for the production of a drill hole, since manual drilling is a force-controlled process. Experimental work was carried out on the bone of a porcine mandible in order to investigate the interrelation of the applied load during drilling. It can be shown that the load application can be subdivided according to the working feed direction. The entire drilling process thus consists of several time domains, which can be divided into the geometry-generating feed motion and a retraction movement of the tool. It has been shown that the removal of the tool from the drill hole has a significant influence on the mechanical load input. This fact is proven in detail by a new evaluation methodology. The causes of this characteristic can also be identified, as well as possible ways of reducing the load input.

Pyro-processes and the wastes

International Nuclear Information System (INIS)

Kurata, Masaki; Tokiwai, Moriyasu; Inoue, Tadashi; Nishimura, Tomohiro

2000-01-01

Reprocessing using pyrometallurgical processes is generally considered to have economical benefits comparing with conventional aqueous processes because of the combination of simpler process and equipments, less criticality, and more compact facilities. On the other hand, the pyrometallurgical processes must generate peculiar wastes and R and D on those wastes is slightly inferior, as compared with the main processes. In this paper, process flows of major pyrometallurgical processes are firstly summarized and, then, the present R and D condition on the wastes are shown. (author)

Chemical process hazards analysis

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-01

The Office of Worker Health and Safety (EH-5) under the Assistant Secretary for the Environment, Safety and Health of the US Department (DOE) has published two handbooks for use by DOE contractors managing facilities and processes covered by the Occupational Safety and Health Administration (OSHA) Rule for Process Safety Management of Highly Hazardous Chemicals (29 CFR 1910.119), herein referred to as the PSM Rule. The PSM Rule contains an integrated set of chemical process safety management elements designed to prevent chemical releases that can lead to catastrophic fires, explosions, or toxic exposures. The purpose of the two handbooks, ``Process Safety Management for Highly Hazardous Chemicals`` and ``Chemical Process Hazards Analysis,`` is to facilitate implementation of the provisions of the PSM Rule within the DOE. The purpose of this handbook ``Chemical Process Hazards Analysis,`` is to facilitate, within the DOE, the performance of chemical process hazards analyses (PrHAs) as required under the PSM Rule. It provides basic information for the performance of PrHAs, and should not be considered a complete resource on PrHA methods. Likewise, to determine if a facility is covered by the PSM rule, the reader should refer to the handbook, ``Process Safety Management for Highly Hazardous Chemicals`` (DOE- HDBK-1101-96). Promulgation of the PSM Rule has heightened the awareness of chemical safety management issues within the DOE. This handbook is intended for use by DOE facilities and processes covered by the PSM rule to facilitate contractor implementation of the PrHA element of the PSM Rule. However, contractors whose facilities and processes not covered by the PSM Rule may also use this handbook as a basis for conducting process hazards analyses as part of their good management practices. This handbook explains the minimum requirements for PrHAs outlined in the PSM Rule. Nowhere have requirements been added beyond what is specifically required by the rule.

Software Process Improvement Defined

DEFF Research Database (Denmark)

Aaen, Ivan

2002-01-01

This paper argues in favor of the development of explanatory theory on software process improvement. The last one or two decades commitment to prescriptive approaches in software process improvement theory may contribute to the emergence of a gulf dividing theorists and practitioners....... It is proposed that this divide be met by the development of theory evaluating prescriptive approaches and informing practice with a focus on the software process policymaking and process control aspects of improvement efforts...

Modeling multiphase materials processes

CERN Document Server

Iguchi, Manabu

2010-01-01

""Modeling Multiphase Materials Processes: Gas-Liquid Systems"" describes the methodology and application of physical and mathematical modeling to multi-phase flow phenomena in materials processing. The book focuses on systems involving gas-liquid interaction, the most prevalent in current metallurgical processes. The performance characteristics of these processes are largely dependent on transport phenomena. This volume covers the inherent characteristics that complicate the modeling of transport phenomena in such systems, including complex multiphase structure, intense turbulence, opacity of

Fuel processing

International Nuclear Information System (INIS)

Allardice, R.H.

1990-01-01

The technical and economic viability of the fast breeder reactor as an electricity generating system depends not only upon the reactor performance but also on a capability to recycle plutonium efficiently, reliably and economically through the reactor and fuel cycle facilities. Thus the fuel cycle is an integral and essential part of the system. Fuel cycle research and development has focused on demonstrating that the challenging technical requirements of processing plutonium fuel could be met and that the sometimes conflicting requirements of the fuel developer, fuel fabricator and fuel reprocessor could be reconciled. Pilot plant operation and development and design studies have established both the technical and economic feasibility of the fuel cycle but scope for further improvement exists through process intensification and flowsheet optimization. These objectives and the increasing processing demands made by the continuing improvement to fuel design and irradiation performance provide an incentive for continuing fuel cycle development work. (author)

From mineral processing to waste treatment: an open-mind process simulator

International Nuclear Information System (INIS)

Guillaneau, J.C.; Brochot, S.; Durance, M.V.; Villeneuve, J.; Fourniguet, G.; Vedrine, H.; Sandvik, K.; Reuter, M.

1999-01-01

More than two hundred companies are using the USIM PAC process simulator within the mineral industry world-wide. Either for design or plant adaptation, simulation is increasingly supporting the process Engineer in his activities. From the mineral field, new domains have been concerned by this model-based approach as new models are developed and new applications involving solid waste appears. Examples are presented in bio-processing, steel-making flue dust treatment for zinc valorisation, soil decontamination or urban waste valorisation (sorting, composting and incineration). (author)

Serial Learning Process: Test of Chaining, Position, and Dual-Process Hypotheses

Science.gov (United States)

Giurintano, S. L.

1973-01-01

The chaining, position, and dual-process hypotheses of serial learning (SL) as well as serial recall, reordering, and relearning of paired-associate learning were examined to establish learning patterns. Results provide evidence for dual-process hypothesis. (DS)

Nonhomogeneous fractional Poisson processes

International Nuclear Information System (INIS)

Wang Xiaotian; Zhang Shiying; Fan Shen

2007-01-01

In this paper, we propose a class of non-Gaussian stationary increment processes, named nonhomogeneous fractional Poisson processes W H (j) (t), which permit the study of the effects of long-range dependance in a large number of fields including quantum physics and finance. The processes W H (j) (t) are self-similar in a wide sense, exhibit more fatter tail than Gaussian processes, and converge to the Gaussian processes in distribution in some cases. In addition, we also show that the intensity function λ(t) strongly influences the existence of the highest finite moment of W H (j) (t) and the behaviour of the tail probability of W H (j) (t)

Processed and ultra-processed foods are associated with lower-quality nutrient profiles in children from Colombia.

Science.gov (United States)

Cornwell, Brittany; Villamor, Eduardo; Mora-Plazas, Mercedes; Marin, Constanza; Monteiro, Carlos A; Baylin, Ana

2018-01-01

To determine if processed and ultra-processed foods consumed by children in Colombia are associated with lower-quality nutrition profiles than less processed foods. We obtained information on sociodemographic and anthropometric variables and dietary information through dietary records and 24 h recalls from a convenience sample of the Bogotá School Children Cohort. Foods were classified into three categories: (i) unprocessed and minimally processed foods, (ii) processed culinary ingredients and (iii) processed and ultra-processed foods. We also examined the combination of unprocessed foods and processed culinary ingredients. Representative sample of children from low- to middle-income families in Bogotá, Colombia. Children aged 5-12 years in 2011 Bogotá School Children Cohort. We found that processed and ultra-processed foods are of lower dietary quality in general. Nutrients that were lower in processed and ultra-processed foods following adjustment for total energy intake included: n-3 PUFA, vitamins A, B12, C and E, Ca and Zn. Nutrients that were higher in energy-adjusted processed and ultra-processed foods compared with unprocessed foods included: Na, sugar and trans-fatty acids, although we also found that some healthy nutrients, including folate and Fe, were higher in processed and ultra-processed foods compared with unprocessed and minimally processed foods. Processed and ultra-processed foods generally have unhealthy nutrition profiles. Our findings suggest the categorization of foods based on processing characteristics is promising for understanding the influence of food processing on children's dietary quality. More studies accounting for the type and degree of food processing are needed.

A taxonomy of business processes

OpenAIRE

ANGEL ANTONIO DIAZ; Luis Eduardo Solís

2004-01-01

This study aims to gain a better understanding of key business processes. The processes of the firm are analyzed, proposing a classification of eight generic intra-organizational processes, and eleven generic inter-organizational processes, as well as criteria for the determination of the criticality of these processes and key performance indicators. Using these criteria critical intra-organizational and inter-organizational processes are identified in sixteen industrial sectors. Through a be...

Neuroscientific Model of Motivational Process

OpenAIRE

Kim, Sung-il

2013-01-01

Considering the neuroscientific findings on reward, learning, value, decision-making, and cognitive control, motivation can be parsed into three sub processes, a process of generating motivation, a process of maintaining motivation, and a process of regulating motivation. I propose a tentative neuroscientific model of motivational processes which consists of three distinct but continuous sub processes, namely reward-driven approach, value-based decision-making, and goal-directed control. Rewa...

Food processing and allergenicity.

Science.gov (United States)

Verhoeckx, Kitty C M; Vissers, Yvonne M; Baumert, Joseph L; Faludi, Roland; Feys, Marcel; Flanagan, Simon; Herouet-Guicheney, Corinne; Holzhauser, Thomas; Shimojo, Ryo; van der Bolt, Nieke; Wichers, Harry; Kimber, Ian

2015-06-01

Food processing can have many beneficial effects. However, processing may also alter the allergenic properties of food proteins. A wide variety of processing methods is available and their use depends largely on the food to be processed. In this review the impact of processing (heat and non-heat treatment) on the allergenic potential of proteins, and on the antigenic (IgG-binding) and allergenic (IgE-binding) properties of proteins has been considered. A variety of allergenic foods (peanuts, tree nuts, cows' milk, hens' eggs, soy, wheat and mustard) have been reviewed. The overall conclusion drawn is that processing does not completely abolish the allergenic potential of allergens. Currently, only fermentation and hydrolysis may have potential to reduce allergenicity to such an extent that symptoms will not be elicited, while other methods might be promising but need more data. Literature on the effect of processing on allergenic potential and the ability to induce sensitisation is scarce. This is an important issue since processing may impact on the ability of proteins to cause the acquisition of allergic sensitisation, and the subject should be a focus of future research. Also, there remains a need to develop robust and integrated methods for the risk assessment of food allergenicity. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

Monitoring of operating processes

International Nuclear Information System (INIS)

Barry, R.F.

1981-01-01

Apparatus is described for monitoring the processes of a nuclear reactor to detect off-normal operation of any process and for testing the monitoring apparatus. The processes are evaluated by response to their paramters, such as temperature, pressure, etc. The apparatus includes a pair of monitoring paths or signal processing units. Each unit includes facilities for receiving on a time-sharing basis, a status binary word made up of digits each indicating the status of a process, whether normal or off-normal, and test-signal binary words simulating the status binary words. The status words and test words are processed in succession during successive cycles. During each cycle, the two units receive the same status word and the same test word. The test words simulate the status words both when they indicate normal operation and when they indicate off-normal operation. Each signal-processing unit includes a pair of memories. Each memory receives a status word or a test word, as the case may be, and converts the received word into a converted status word or a converted test word. The memories of each monitoring unit operate into a non-coincidence which signals non-coincidence of the converted word out of one memory of a signal-processing unit not identical to the converted word of the other memory of the same unit

Process cubes : slicing, dicing, rolling up and drilling down event data for process mining

NARCIS (Netherlands)

Aalst, van der W.M.P.

2013-01-01

Recent breakthroughs in process mining research make it possible to discover, analyze, and improve business processes based on event data. The growth of event data provides many opportunities but also imposes new challenges. Process mining is typically done for an isolated well-defined process in

Gas processing device

International Nuclear Information System (INIS)

Kobayashi, Yoshihiro; Seki, Eiji.

1991-01-01

State of electric discharge is detected based on a gas pressure in a sealed container and a discharging current flowing between both of electrodes. When electric arc discharges occur, introduction of gases to be processed is stopped and a voltage applied to both of the electrodes is interrupted. Then, when the gas pressure in the sealed container is lowered to a predetermined value, a power source voltage is applied again to both of the electrodes to recover glow discharges, and the introduction of the gas to be processed is started. With such steps, even if electric arc discharges occur, they are eliminated automatically and, accordingly, normal glow discharges can be recovered, to prevent failures of the device due to electric arc discharges. The glow discharges are recovered automatically without stopping the operation of the gas processing device, and gas injection and solidification processing can be conducted continuously and stably. (T.M.)

Preliminary evaluation of alternative waste form solidification processes. Volume II. Evaluation of the processes

International Nuclear Information System (INIS)

1980-08-01

This Volume II presents engineering feasibility evaluations of the eleven processes for solidification of nuclear high-level liquid wastes (HHLW) described in Volume I of this report. Each evaluation was based in a systematic assessment of the process in respect to six principal evaluation criteria: complexity of process; state of development; safety; process requirements; development work required; and facility requirements. The principal criteria were further subdivided into a total of 22 subcriteria, each of which was assigned a weight. Each process was then assigned a figure of merit, on a scale of 1 to 10, for each of the subcriteria. A total rating was obtained for each process by summing the products of the subcriteria ratings and the subcriteria weights. The evaluations were based on the process descriptions presented in Volume I of this report, supplemented by information obtained from the literature, including publications by the originators of the various processes. Waste form properties were, in general, not evaluated. This document describes the approach which was taken, the developent and application of the rating criteria and subcriteria, and the evaluation results. A series of appendices set forth summary descriptions of the processes and the ratings, together with the complete numerical ratings assigned; two appendices present further technical details on the rating process

Dosimetry for radiation processing

DEFF Research Database (Denmark)

Miller, Arne

1986-01-01

During the past few years significant advances have taken place in the different areas of dosimetry for radiation processing, mainly stimulated by the increased interest in radiation for food preservation, plastic processing and sterilization of medical products. Reference services both...... and sterilization dosimetry, optichromic dosimeters in the shape of small tubes for food processing, and ESR spectroscopy of alanine for reference dosimetry. In this paper the special features of radiation processing dosimetry are discussed, several commonly used dosimeters are reviewed, and factors leading...

Process equipment waste and process waste liquid collection systems

International Nuclear Information System (INIS)

1990-06-01

The US DOE has prepared an environmental assessment for construction related to the Process Equipment Waste (PEW) and Process Waste Liquid (PWL) Collection System Tasks at the Idaho Chemical Processing Plant. This report describes and evaluates the environmental impacts of the proposed action (and alternatives). The purpose of the proposed action would be to ensure that the PEW and PWL collection systems, a series of enclosed process hazardous waste, and radioactive waste lines and associated equipment, would be brought into compliance with applicable State and Federal hazardous waste regulations. This would be accomplished primarily by rerouting the lines to stay within the buildings where the lined floors of the cells and corridors would provide secondary containment. Leak detection would be provided via instrumented collection sumps locate din the cells and corridors. Hazardous waste transfer lines that are routed outside buildings will be constructed using pipe-in-pipe techniques with leak detection instrumentation in the interstitial area. The need for the proposed action was identified when a DOE-sponsored Resource Conservation and Recovery Act (RCRA) compliance assessment of the ICPP facilities found that singly-contained waste lines ran buried in the soil under some of the original facilities. These lines carried wastes with a pH of less than 2.0, which were hazardous waste according to the RCRA standards. 20 refs., 7 figs., 1 tab

A DMAIC approach for process capability improvement an engine crankshaft manufacturing process

Science.gov (United States)

Sharma, G. V. S. S.; Rao, P. Srinivasa

2014-05-01

The define-measure-analyze-improve-control (DMAIC) approach is a five-strata approach, namely DMAIC. This approach is the scientific approach for reducing the deviations and improving the capability levels of the manufacturing processes. The present work elaborates on DMAIC approach applied in reducing the process variations of the stub-end-hole boring operation of the manufacture of crankshaft. This statistical process control study starts with selection of the critical-to-quality (CTQ) characteristic in the define stratum. The next stratum constitutes the collection of dimensional measurement data of the CTQ characteristic identified. This is followed by the analysis and improvement strata where the various quality control tools like Ishikawa diagram, physical mechanism analysis, failure modes effects analysis and analysis of variance are applied. Finally, the process monitoring charts are deployed at the workplace for regular monitoring and control of the concerned CTQ characteristic. By adopting DMAIC approach, standard deviation is reduced from 0.003 to 0.002. The process potential capability index ( C P) values improved from 1.29 to 2.02 and the process performance capability index ( C PK) values improved from 0.32 to 1.45, respectively.

A systematic synthesis and design methodology to achieve process intensification in (bio) chemical processes

DEFF Research Database (Denmark)

Lutze, Philip; Román-Martinez, Alicia; Woodley, John

2010-01-01

Process intensification (PI) has the potential to improve existing processes or create new process options which are needed in order to produce products using more sustainable methods. PI creates an enormous number of process options. In order to manage the complexity of options in which a feasib...

Radiation processing of minimally processed fruits and vegetables to ensure microbiological safety

International Nuclear Information System (INIS)

Bandekar, J.R.; Saroj, S.D.; Shashidhar, R.; Dhokane, V.S.; Hajare, S.N.; Nagar, V.; Sharma, A.

2009-01-01

Minimally processed fruits and vegetables are in demand as they offer ready rich source of nutrients and convenience to consumers. However, these products are often unsafe due to contamination with harmful pathogens. Therefore, a study was carried out to analyze microbiological quality of minimally processed fruits, vegetables and sprouts and to optimize radiation dose necessary to ensure safety of these commodities. Microbiological quality of these products was found to be poor. Decimal reduction dose (D 10 ) for Salmonella Typhimurium and Listeria monocytogenes in these minimally processed foods (MPF) were in the range of 164 to 588 Gy. Radiation processing with 2 kGy dose of gamma radiation resulted in 5 log reduction of S. Typhimurium and 4 log reduction of L. monocytogenes. The treatment did not significantly affect nutritional, organoleptic and textural properties. These results suggest that radiation processing can ensure safety of these products. (author)

Property optimization of nanostructured ARB-processed Al by post-process deformation

DEFF Research Database (Denmark)

Huang, Xiaoxu; Kamikawa, Naoya; Hansen, Niels

2008-01-01

The effect of post-process deformation on the mechanical properties of nanostructured aluminum (99.2% purity) has been investigated by cold rolling of samples which have been processed by accumulative roll bonding (ARB) to a strain of epsilon(vM) = 4.8. Samples have been cold rolled to 10, 15...... material. In contrary, cold rolling to large strain (50%) results in significant strengthening. This leads to the suggestion of a transition strain within the range of 25-35% reduction by rolling. The microstructural evolution during post-process deformation has been followed by transmission electron...

Generic Health Management: A System Engineering Process Handbook Overview and Process

Science.gov (United States)

Wilson, Moses Lee; Spruill, Jim; Hong, Yin Paw

1995-01-01

Health Management, a System Engineering Process, is one of those processes-techniques-and-technologies used to define, design, analyze, build, verify, and operate a system from the viewpoint of preventing, or minimizing, the effects of failure or degradation. It supports all ground and flight elements during manufacturing, refurbishment, integration, and operation through combined use of hardware, software, and personnel. This document will integrate Health Management Processes (six phases) into five phases in such a manner that it is never a stand alone task/effort which separately defines independent work functions.

Classical higher-order processes

DEFF Research Database (Denmark)

Montesi, Fabrizio

2017-01-01

Classical Processes (CP) is a calculus where the proof theory of classical linear logic types processes à la Π-calculus, building on a Curry-Howard correspondence between session types and linear propositions. We contribute to this research line by extending CP with process mobility, inspired by ...

Real-time radar signal processing using GPGPU (general-purpose graphic processing unit)

Science.gov (United States)

Kong, Fanxing; Zhang, Yan Rockee; Cai, Jingxiao; Palmer, Robert D.

2016-05-01

This study introduces a practical approach to develop real-time signal processing chain for general phased array radar on NVIDIA GPUs(Graphical Processing Units) using CUDA (Compute Unified Device Architecture) libraries such as cuBlas and cuFFT, which are adopted from open source libraries and optimized for the NVIDIA GPUs. The processed results are rigorously verified against those from the CPUs. Performance benchmarked in computation time with various input data cube sizes are compared across GPUs and CPUs. Through the analysis, it will be demonstrated that GPGPUs (General Purpose GPU) real-time processing of the array radar data is possible with relatively low-cost commercial GPUs.

What do information reuse and automated processing require in engineering design? Semantic process

Directory of Open Access Journals (Sweden)

Ossi Nykänen

2011-12-01

Full Text Available Purpose: The purpose of this study is to characterize, analyze, and demonstrate machine-understandable semantic process for validating, integrating, and processing technical design information. This establishes both a vision and tools for information reuse and semi-automatic processing in engineering design projects, including virtual machine laboratory applications with generated components.Design/methodology/approach: The process model has been developed iteratively in terms of action research, constrained by the existing technical design practices and assumptions (design documents, expert feedback, available technologies (pre-studies and experiments with scripting and pipeline tools, benchmarking with other process models and methods (notably the RUP and DITA, and formal requirements (computability and the critical information paths for the generated applications. In practice, the work includes both quantitative and qualitative components.Findings: Technical design processes may be greatly enhanced in terms of semantic process thinking, by enriching design information, and automating information validation and transformation tasks. Contemporary design information, however, is mainly intended for human consumption, and needs to be explicitly enriched with the currently missing data and interfaces. In practice, this may require acknowledging the role of technical information or knowledge engineer, to lead the development of the semantic design information process in a design organization. There is also a trade-off between machine-readability and system complexity that needs to be studied further, both empirically and in theory.Research limitations/implications: The conceptualization of the semantic process is essentially an abstraction based on the idea of progressive design. While this effectively allows implementing semantic processes with, e.g., pipeline technologies, the abstraction is valid only when technical design is organized into

Customer Innovation Process Leadership

DEFF Research Database (Denmark)

Lindgren, Peter; Jørgensen, Jacob Høj; Goduscheit, René Chester

2007-01-01

Innovation leadership has traditionally been focused on leading the companies' product development fast, cost effectively and with an optimal performance driven by technological inventions or by customers´ needs. To improve the efficiency of the product development process focus has been on diffe......Innovation leadership has traditionally been focused on leading the companies' product development fast, cost effectively and with an optimal performance driven by technological inventions or by customers´ needs. To improve the efficiency of the product development process focus has been...... on different types of organisational setup to the product development model and process. The globalization and enhanced competitive markets are however changing the innovation game and the challenge to innovation leadership Excellent product development innovation and leadership seems not any longer to enough...... another outlook to future innovation leadership - Customer Innovation Process Leadership - CIP-leadership. CIP-leadership moves the company's innovation process closer to the customer innovation process and discusses how companies can be involved and innovate in customers' future needs and lead...

Multi-enzyme Process Modeling

DEFF Research Database (Denmark)

Andrade Santacoloma, Paloma de Gracia

are affected (in a positive or negative way) by the presence of the other enzymes and compounds in the media. In this thesis the concept of multi-enzyme in-pot term is adopted for processes that are carried out by the combination of enzymes in a single reactor and implemented at pilot or industrial scale...... features of the process and provides the information required to structure the process model by using a step-by-step procedure with the required tools and methods. In this way, this framework increases efficiency of the model development process with respect to time and resources needed (fast and effective....... In this way the model parameters that drives the main dynamic behavior can be identified and thus a better understanding of this type of processes. In order to develop, test and verify the methodology, three case studies were selected, specifically the bi-enzyme process for the production of lactobionic acid...

Business process intelligence

NARCIS (Netherlands)

Castellanos, M.; Alves De Medeiros, A.K.; Mendling, J.; Weber, B.; Weijters, A.J.M.M.; Cardoso, J.; Aalst, van der W.M.P.

2009-01-01

Business Process Intelligence (BPI,) is an emerging area that is getting increasingly popularfor enterprises. The need to improve business process efficiency, to react quickly to changes and to meet regulatory compliance is among the main drivers for BPI. BPI refers to the application of Business

Continuous affine processes

DEFF Research Database (Denmark)

Buchardt, Kristian

2016-01-01

Affine processes possess the property that expectations of exponential affine transformations are given by a set of Riccati differential equations, which is the main feature of this popular class of processes. In this paper we generalise these results for expectations of more general transformati...

DWPF process control

International Nuclear Information System (INIS)

Heckendoin, F.M. II

1983-01-01

The Defense Waste Processing Facility (DWPF) for waste vitrification at the Savannah River Plant (SRP) is in the final design stage. Instrumentation to provide the parameter sensing required to assure the quality of the two-foot-diameter, ten-foot-high waste canister is in the final stage of development. All step of the process and instrumentation are now operating as nearly full-scale prototypes at SRP. Quality will be maintained by assuring that only the intended material enters the canisters, and by sensing the resultant condition of the filled canisters. Primary emphasis will be on instrumentation of the process

Quantum Information Processing

CERN Document Server

Leuchs, Gerd

2005-01-01

Quantum processing and communication is emerging as a challenging technique at the beginning of the new millennium. This is an up-to-date insight into the current research of quantum superposition, entanglement, and the quantum measurement process - the key ingredients of quantum information processing. The authors further address quantum protocols and algorithms. Complementary to similar programmes in other countries and at the European level, the German Research Foundation (DFG) started a focused research program on quantum information in 1999. The contributions - written by leading experts - bring together the latest results in quantum information as well as addressing all the relevant questions

A Robust Process Analytical Technology (PAT) System Design for Crystallization Processes

DEFF Research Database (Denmark)

Abdul Samad, Noor Asma Fazli Bin; Sin, Gürkan; Gernaey, Krist

2013-01-01

A generic computer-aided framework for systematic design of a process monitoring and control system for crystallization processes has been developed to study various aspects of crystallization operations. The design framework contains a generic multidimensional modelling framework, a tool for gen...

Process for recovering yttrium and lanthanides from wet-process phosphoric acid

Energy Technology Data Exchange (ETDEWEB)

Janssen, J.A.; Weterings, C.A.

1983-06-28

Process for recovering yttrium and lanthanides from wet-process phosphoric acid by adding a flocculant to the phosphoric acid, separating out the resultant precipitate and then recovering yttrium and lanthanides from the precipitate. Uranium is recovered from the remaining phosphoric acid.

Process-aware information systems : bridging people and software through process technology

NARCIS (Netherlands)

Dumas, M.; Aalst, van der W.M.P.; Hofstede, ter A.H.M.

2005-01-01

A unifying foundation to design and implement process-aware information systems This publication takes on the formidable task of establishing a unifying foundation and set of common underlying principles to effectively model, design, and implement process-aware information systems. Authored by

Process evaluation of discharge planning implementation in healthcare using normalization process theory.

Science.gov (United States)

Nordmark, Sofi; Zingmark, Karin; Lindberg, Inger

2016-04-27

Discharge planning is a care process that aims to secure the transfer of care for the patient at transition from home to the hospital and back home. Information exchange and collaboration between care providers are essential, but deficits are common. A wide range of initiatives to improve the discharge planning process have been developed and implemented for the past three decades. However, there are still high rates of reported medical errors and adverse events related to failures in the discharge planning. Using theoretical frameworks such as Normalization Process Theory (NPT) can support evaluations of complex interventions and processes in healthcare. The aim of this study was to explore the embedding and integration of the DPP from the perspective of registered nurses, district nurses and homecare organizers. The study design was explorative, using the NPT as a framework to explore the embedding and integration of the DPP. Data consisted of written documentation from; workshops with staff, registered adverse events and system failures, web based survey and individual interviews with staff. Using the NPT as a framework to explore the embedding and integration of discharge planning after 10 years in use showed that the staff had reached a consensus of opinion of what the process was (coherence) and how they evaluated the process (reflexive monitoring). However, they had not reached a consensus of opinion of who performed the process (cognitive participation) and how it was performed (collective action). This could be interpreted as the process had not become normalized in daily practice. The result shows necessity to observe the implementation of old practices to better understand the needs of new ones before developing and implementing new practices or supportive tools within healthcare to reach the aim of development and to accomplish sustainable implementation. The NPT offers a generalizable framework for analysis, which can explain and shape the