WorldWideScience

Sample records for survival craft tempsc

  1. 46 CFR 133.105 - Survival craft.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Survival craft. 133.105 Section 133.105 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OFFSHORE SUPPLY VESSELS LIFESAVING SYSTEMS Requirements for All OSVs § 133.105 Survival craft. (a) Each survival craft must be approved and equipped as...

  2. 46 CFR 199.201 - Survival craft.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Survival craft. 199.201 Section 199.201 Shipping COAST... SYSTEMS FOR CERTAIN INSPECTED VESSELS Additional Requirements for Passenger Vessels § 199.201 Survival craft. (a) Each survival craft must be approved and equipped as follows: (1) Each lifeboat must be...

  3. 46 CFR 199.261 - Survival craft.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Survival craft. 199.261 Section 199.261 Shipping COAST... SYSTEMS FOR CERTAIN INSPECTED VESSELS Additional Requirements for Cargo Vessels § 199.261 Survival craft. (a) Each survival craft must be approved and equipped as follows: (1) Each lifeboat must be a totally...

  4. 46 CFR 28.120 - Survival craft.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Survival craft. 28.120 Section 28.120 Shipping COAST... VESSELS Requirements for All Vessels § 28.120 Survival craft. (a) Except as provided in paragraphs (b) through (h) of this section and 28.305, each vessel must carry the survival craft specified in Table 28...

  5. 46 CFR 117.130 - Stowage of survival craft.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Stowage of survival craft. 117.130 Section 117.130... AND ARRANGEMENTS Survival Craft Arrangements and Equipment § 117.130 Stowage of survival craft. (a) Each survival craft must be: (1) Secured to the vessel by a painter with a float-free link permanently...

  6. 46 CFR 133.130 - Stowage of survival craft.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Stowage of survival craft. 133.130 Section 133.130... SYSTEMS Requirements for All OSVs § 133.130 Stowage of survival craft. (a) General. Each survival craft must be stowed as follows: (1) Each survival craft must be as close to the accommodation and service...

  7. 46 CFR 180.130 - Stowage of survival craft.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Stowage of survival craft. 180.130 Section 180.130... TONS) LIFESAVING EQUIPMENT AND ARRANGEMENTS Survival Craft Arrangements and Equipment § 180.130 Stowage of survival craft. (a) Each survival craft must be: (1) Secured to the vessel by a painter with a...

  8. 46 CFR 28.310 - Launching of survival craft.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Launching of survival craft. 28.310 Section 28.310... Operate With More Than 16 Individuals on Board § 28.310 Launching of survival craft. A gate or other... each survival craft which weighs more than 110 pounds (489 Newtons), to allow the survival craft to be...

  9. 46 CFR 108.530 - Stowage of survival craft.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Stowage of survival craft. 108.530 Section 108.530... AND EQUIPMENT Lifesaving Equipment § 108.530 Stowage of survival craft. (a) General. Each survival... follows: (1) Each survival craft must be stowed as close to the accommodation and service spaces as...

  10. 46 CFR 28.805 - Launching of survival craft.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Launching of survival craft. 28.805 Section 28.805... FISHING INDUSTRY VESSELS Aleutian Trade Act Vessels § 28.805 Launching of survival craft. In addition to the survival craft requirements in subpart B, each vessel must have a gate or other opening in the...

  11. 46 CFR 199.130 - Stowage of survival craft.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Stowage of survival craft. 199.130 Section 199.130... LIFESAVING SYSTEMS FOR CERTAIN INSPECTED VESSELS Requirements for All Vessels § 199.130 Stowage of survival craft. (a) General. Each survival craft must be stowed— (1) As close to the accommodation and service...

  12. 46 CFR 199.290 - Stowage of survival craft.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Stowage of survival craft. 199.290 Section 199.290... of survival craft. (a) To meet the requirements of § 199.130(b)(1), each lifeboat— (1) On a cargo... required under § 199.261(e), no stowage position or muster and embarkation station for a survival craft on...

  13. 46 CFR 199.230 - Stowage of survival craft.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Stowage of survival craft. 199.230 Section 199.230... Stowage of survival craft. (a) To meet the requirements of § 199.130(b)(1), each lifeboat on a passenger... height of a survival craft must take into account the vessel's escape provisions, the vessel's size, and...

  14. 46 CFR 108.520 - Type of survival craft.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Type of survival craft. 108.520 Section 108.520 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Lifesaving Equipment § 108.520 Type of survival craft. (a) Each lifeboat must be a fire-protected...

  15. 46 CFR 28.125 - Stowage of survival craft.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Stowage of survival craft. 28.125 Section 28.125 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY UNINSPECTED VESSELS REQUIREMENTS FOR COMMERCIAL FISHING INDUSTRY VESSELS Requirements for All Vessels § 28.125 Stowage of survival craft. (a) Each...

  16. 33 CFR 146.120 - Manning of survival craft.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Manning of survival craft. 146... (CONTINUED) OUTER CONTINENTAL SHELF ACTIVITIES OPERATIONS Manned OCS Facilities § 146.120 Manning of survival..., lifeboat, life raft, or survival capsule who shall be responsible for launching it in event of an emergency. ...

  17. 46 CFR 199.220 - Survival craft and rescue boat embarkation arrangements.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Survival craft and rescue boat embarkation arrangements... Passenger Vessels § 199.220 Survival craft and rescue boat embarkation arrangements. (a) Survival craft... rescue boat must be able to be boarded and launched directly from the stowed position with the number of...

  18. 46 CFR 133.175 - Survival craft and rescue boat equipment.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Survival craft and rescue boat equipment. 133.175... LIFESAVING SYSTEMS Requirements for All OSVs § 133.175 Survival craft and rescue boat equipment. (a) All rescue boat equipment must be as follows: (1) The equipment must be secured within the boat by lashings...

  19. 46 CFR 108.575 - Survival craft and rescue boat equipment.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Survival craft and rescue boat equipment. 108.575... DRILLING UNITS DESIGN AND EQUIPMENT Lifesaving Equipment § 108.575 Survival craft and rescue boat equipment. (a) All lifeboat and rescue boat equipment must be as follows: (1) The equipment must be secured...

  20. 46 CFR 117.206 - Survival craft-vessels operating on Great Lakes routes.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Survival craft-vessels operating on Great Lakes routes...—vessels operating on Great Lakes routes. (a) Except as allowed by paragraph (b) of this section, each vessel certificated to operate on a Great Lakes route must be provided with the survival craft required...

  1. 46 CFR 180.206 - Survival craft-vessels operating on Great Lakes routes.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Survival craft-vessels operating on Great Lakes routes... Craft § 180.206 Survival craft—vessels operating on Great Lakes routes. (a) Except as allowed by paragraph (b) of this section, each vessel certificated to operate on a Great Lakes route must be provided...

  2. CRAFT

    DEFF Research Database (Denmark)

    Gammelgaard Nielsen, Anders

    2012-01-01

    for the design has been to reflect upon the importance of craftsmanship in relation to the contemporary building culture. Is there any future at all for craftsmanship in a building culture, which in recent years has undergone a major industrialization? Or should craftsmanship left be to a life in open-air...... museums, as a performing art in front of an audience. In this article the author discusses the importance of craft and craftsmanship in contemporary architecture in relation to its users....

  3. 46 CFR 25.25-17 - Survival craft requirements for uninspected passenger vessels of at least 100 gross tons.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Survival craft requirements for uninspected passenger... Survival craft requirements for uninspected passenger vessels of at least 100 gross tons. (a) Each uninspected passenger vessel of at least 100 gross tons must have adequate survival craft with enough capacity...

  4. 46 CFR 111.75-16 - Lighting of survival craft and rescue boats.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Lighting of survival craft and rescue boats. 111.75-16... ELECTRIC SYSTEMS-GENERAL REQUIREMENTS Lighting Circuits and Protection § 111.75-16 Lighting of survival... be adequately illuminated by lighting supplied from the emergency power source. (b) The arrangement...

  5. 46 CFR 180.202 - Survival craft-vessels operating on oceans routes.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Survival craft-vessels operating on oceans routes. 180... § 180.202 Survival craft—vessels operating on oceans routes. (a) Each vessel certificated to operate on an oceans route in cold water must either: (1) Be provided with inflatable buoyant apparatus of an...

  6. 46 CFR 117.202 - Survival craft-vessels operating on oceans routes.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Survival craft-vessels operating on oceans routes. 117... operating on oceans routes. (a) Except as allowed by paragraph (b) of this section, each vessel certificated to operate on an oceans route in cold water must be provided with inflatable liferafts of an...

  7. Comparison of Survival and Safety Requirements in European Union for Recreational Craft Inspections. A Spanish Case Study

    Directory of Open Access Journals (Sweden)

    J. Torralbo

    2014-03-01

    Full Text Available Statistical data shows that a large number of maritime accidents are related to recreational craft. For instance, in Spain, more than fifty percent of the emergencies are related to pleasure boats at sea. Recreational craft marketed in the EU must comply with harmonized technical safety and environmental requirements defined by Directive 94/25/EC, as amended in 2003. On 28 December 2013, the new recreational craft directive 2013/53/EU was published in the Official Journal of the European Union. EU Member States have until 18 January 2016 to amend their national legislation and transpose the new directive. The current directive 94/25/EC as amended by directive 2003/44/EC will be repealed on 18 January 2016, after the full application of the new text. Although this directive, there is not a clear coordination and equivalence among the EU countries according to the survival and safety equipment compulsory for recreational crafts. The main purpose of this paper is to analyze and compare the types of survey / inspections to be carried in pleasure craft (non-commercial use, periodicity and required safety equipment in some member states of the European Union. A case study of Spain is presented. From the results obtained, we can make clear that in the European Union there is a lack of coordination in this area and indicate the need to unify a common pattern in inspections and survival and safety requirements of recreational boats in the EU.

  8. Transformation Craft (T-Craft) Concept Study

    National Research Council Canada - National Science Library

    Marks, Cynthia; Phelps, Chance; Ryan, Justin; Sorensen, Paul

    2007-01-01

    The objective of the Transformation Craft (T-Craft) innovation team was to develop a conceptual craft that addresses the problem of transporting military vehicles at high speed from the Sea Base to troops inland...

  9. Space Craft

    Science.gov (United States)

    Demski, Jennifer

    2009-01-01

    This article discusses how craft innovative architecture is bringing form to the function of 21st-century learning. It describes the construction of New Tech High at Coppell, in Coppell, Texas, which produces an example of how workplace design principles can be coordinated with modern educational goals. The campus was built on the model of New…

  10. 33 CFR 149.303 - What survival craft and rescue boats may be used on a manned deepwater port?

    Science.gov (United States)

    2010-07-01

    ... boats may be used on a manned deepwater port? 149.303 Section 149.303 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) DEEPWATER PORTS DEEPWATER PORTS: DESIGN, CONSTRUCTION, AND EQUIPMENT Lifesaving Equipment Manned Deepwater Port Requirements § 149.303 What survival...

  11. 33 CFR 149.304 - What type and how many survival craft and rescue boats must a manned deepwater port have?

    Science.gov (United States)

    2010-07-01

    ... craft and rescue boats must a manned deepwater port have? 149.304 Section 149.304 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) DEEPWATER PORTS DEEPWATER PORTS: DESIGN, CONSTRUCTION, AND EQUIPMENT Lifesaving Equipment Manned Deepwater Port Requirements § 149.304...

  12. Implementing digital crafting : developing

    DEFF Research Database (Denmark)

    Tamke, Martin; Ramsgaard Thomsen, Mette

    2010 in the Danish Design Centre in Copenhagen. The exhibition presents 18 designers, architects and people from the crafts that have an innovative take on the future questions of sustainability, new materials and technology. Their products challenge traditional Danish Design and are yet interconnected...... in the countries traits and the way they design. Curated by the Danish Design Centre, The Danish Architectural Centre and the Danish Crafts Organisation groups of three from the different disciplines were identified in 6 scenarios with distinct expression....

  13. The craft of screenwriting

    NARCIS (Netherlands)

    Weijers, G.W.M.

    2014-01-01

    Isn't it ironic? Screenwriting is not something you learn from a book, or a talent that just falls into your lap. Nevertheless, without talent you will never become a great scriptwriter. Above all scriptwriting is a craft that you learn to master by writing, reflecting, and rewriting time after

  14. Air-gap effect on life boat arrangement for a semi-submersible FPU

    OpenAIRE

    Kim, Mun-Sung; Park, Hong-Shik; Jung, Kwang-Hyo; Chun, Ho-Hwan

    2016-01-01

    In the offshore project such as semi-submersible FPU and FPSO, the free fall type life boat called TEMPSC (Totally Enclosed Motor Propelled Survival Craft) has been installed for the use of an emergency evacuation of POB (People on Board) from the topside platform. For the design of life boat arrangement for semi-submersible FPU in the initial design stage, the drop height and launch angle are required fulfill with the limitation of classification society rule and Company requirement, includi...

  15. Crafting digital media

    CERN Document Server

    James, Daniel

    2010-01-01

    Open source software, also known as free software, now offers a creative platform with world-class programs. Just ask the people who have completed high-quality projects or developed popular web 2.0 sites using open source desktop applications. This phenomenon is no longer underground or restricted to techies - there have been more than 61 million downloads of the Audacity audio editor and more than 60 million downloads of the GIMP for Windows photographic tool from SourceForge.net alone. Crafting Digital Media is your foundation course in photographic manipulation, illustration, animation, 3D

  16. A crafting of potentials

    DEFF Research Database (Denmark)

    Kilbourn, Kyle

    In the movement from understanding the past towards creating the future design anthropology, as a discipline, will turn from one with archival qualities to one endowed with potentials for change. One challenge facing design anthropology is how to show relevance for theory generation while also in......-as is complemented by designing for as design anthropologists stage design workshops, span knowledge traditions, and make design moves. Reflecting on my own research process, I trace a few research tools that underline the craft of design anthropology....

  17. Digital wood craft

    DEFF Research Database (Denmark)

    Tamke, Martin; Ramsgaard Thomsen, Mette

    2009-01-01

    In 1995, Robin Evans points out in his book The Projective Cast how the development of techniques changed architecture and the space inhabited in times of Gothic and early Renaissance. We see a parallel phenomenon today, where the interplay of technology and tool gives shape to new design...... integrated field of design and innovation in architectural design and building industry....... (Kolarevic 2005). Yet in opposition to the interwoven fields of design and craft of the late Gothic, today’s building sector is enormously diversified, and a growing complexity in the building process and number of used materials can be observed. This gives an opposite point of departure into a more...

  18. Josiah Wedgwood, Manufacturing and Craft

    DEFF Research Database (Denmark)

    Holt, Robin; Popp, Andrew

    2016-01-01

    Craft and industrial manufacture are often seen as dichotomous, with craft being marginalized during the process of industrialization. We want to look beyond this position, searching for craft in places where it has gone unnoticed and where it might have bloomed anew in the interstices created...... by industrialization. We explore these questions by studying Josiah Wedgwood’s innovative craft and experimental practices, developed through a close reading of his extensive published correspondence. What we offer is a reinterpretation of Wedgwood’s practices positioned against the existing historiography, both...... standard and revisionist. Our reinterpretation is developed through application of a theoretical–methodological framework of phenomenological micro-history, in which craft is thought of primarily as a space that makes possible what Martin Heidegger called ‘occasioning’....

  19. Survival

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — These data provide information on the survival of California red-legged frogs in a unique ecosystem to better conserve this threatened species while restoring...

  20. To craft or not to craft : The relationships between regulatory focus, job crafting and work outcomes

    NARCIS (Netherlands)

    Brenninkmeijer, Veerle|info:eu-repo/dai/nl/182274551; Hekkert-Koning, Marleen

    2015-01-01

    Purpose – The purpose of this paper is to examine relationships between regulatory focus, job crafting, work engagement and perceived employability. Regulatory focus theory distinguishes between promotion-focused individuals, who strive for growth and development, and preventionfocussed individuals,

  1. Learning craft skills. Exploring preschoolers' craft making process

    Directory of Open Access Journals (Sweden)

    Virpi Yliverronen

    2016-06-01

    Full Text Available The aim of this study was to explore a preschooler craft-making process in which 18 preschool novices cut pieces for fabric bags and designed and printed patterns to decorate the bags. Through the task, children were familiarised with a small-scale holistic craft process. The intention was to determine how preschoolers perceived, verbalised and interpreted the craft-making process and how children used bodily expressions when explaining a learned craft skill. The present study relies on the videographic method: two preschool groups’ stamp printing activities were recorded, and each child was interviewed individually. Children’s embodied expressions were particularly in focus in video analysis. The results reveal that all the children were able to sufficiently explain the making phase, however, some children compensated for missing words using bodily and facial expressions and gestures when talking about making. The results showed that children worked logically, and the skill learning phases of perceiving, making, and interpretation were revealed from their learning.

  2. The craft process developing student decision making

    National Research Council Canada - National Science Library

    Marja-Leena Rönkkö; Jaana Lepistö

    2016-01-01

    .... In this study, we examine school students’ decision making during a craft process. The study was conducted during the spring term of 2013 and examines how the students make various decisions during the craft making process...

  3. Methodology Report: Survey of Crafts-Artists.

    Science.gov (United States)

    Cerf, J. George; And Others

    Research concerning crafts-artists in the United States involved two phases: a survey of craft organizations and members and a survey of professional and subscriber crafts-artists. This report describes the sampling, data collection, and data processing procedures used in the surveys, describes the questionnaires and other materials sent to crafts…

  4. Assessing the Art of Craft

    Science.gov (United States)

    Gale, Richard A.; Bond, Lloyd

    2007-01-01

    Assessment of craft in the creative/fine/performing arts is not different in any fundamental way from assessment of other competencies. By investigating the nature of critique and proposing a structural approach to examination/evaluation, we address processes and goals of assessment, providing access points for this difficult aspect of general…

  5. SMALL CRAFT OPERATION AND NAVIGATION.

    Science.gov (United States)

    Louisiana State Dept. of Education, Baton Rouge.

    THIS REFERENCE TEXTBOOK WAS PREPARED FOR USE IN THE FIRST PART OF A TWO-PART COURSE IN MARINE NAVIGATION AND SMALL CRAFT OPERATION ON INLAND AND INTERNATIONAL WATERS. THE MATERIAL WAS DEVELOPED BY AN INDIVIDUAL AUTHOR FOR USE IN TRADE SCHOOL PREPARATORY AND EXTENSION CLASSES FOR MALE ADULTS WHO PLAN TO OPERATE BOATS. IT IS MAINLY CONCERNED WITH…

  6. Craft Generation - Exhibition / Symposium / Workshops / Tour

    OpenAIRE

    Lamb, Andrew

    2015-01-01

    2014 saw a national programme celebrating 25 years of contemporary visual art under the banner of GENERATION.  \\ud \\ud FCA&C (Fife Contemporary Art & Craft) wanted to recognise and celebrate the achievements of Contemporary Scottish Craft practitioners, highlighting creativity, skills, and the career of key individuals as well as and the continuation and renewal of skill and Craftsmanship. \\ud \\ud Established craft artists will exhibited along with artists from the following generation whose ...

  7. Supporting Craft Sense in Early Education

    Directory of Open Access Journals (Sweden)

    Kalle Virta

    2013-10-01

    Full Text Available The research task was to describe and construct theoretical background for Craft Sense in early education. Craft Sense represents a learner’s skill for obtaining Sloyd (Craft, Design & Technology related knowledge, skills and understanding. The development of Craft Sense is based on producing artefacts and evaluating the production process. In this research, the concept of Craft Sense is based on the integration of Sloyd and meta-cognitive regulation of learning activities. Based on theoretical information, an empirical research question was formulated: “What kind of Craft Sense do children have in early education Sloyd?” The method of study was assessing picture supported learning on a Sloyd course for young children. The data was analyzed by qualitative content analysis and Child Behaviour Rating Scale (CBRS. Findings indicate that the development of children’s Craft Sense can be supported with pictures. Furthermore, the CBRS can be used to evaluate and understand children’s Craft Sense. Keywords: Craft Sense, Sloyd, Sloyd Education, Meta-cognition

  8. Research 2009-2011 - Digital Crafting

    DEFF Research Database (Denmark)

    Ramsgaard Thomsen, Mette; Tamke, Martin; Peder Pedersen, Claus

    2012-01-01

    The publication reports on the international research network 'Digital Crafting' organised in the period 2009-2011. The research network investigated profound changes in the design and building of architecture. Developing the term Digital Crafting, the network examined how the maturing...

  9. Teaching: Art, craft, science? Yes!

    Science.gov (United States)

    White, Gary

    2014-09-01

    One of my favorite teachers crafted his lectures like a potter molding clay—not likely into a vase, but rather something more solid and utilitarian, yet still elegant, say, a fruit bowl. Vincent Genusa (Dr. G, we called him) was the only person I have ever known to use the word "prodigious" routinely, referring admiringly to a scientist, or perhaps to the applicability of a particular theoretical method, and he would say it with such relish that sometimes a bit of spittle would be evident, to put it delicately. It was impossible not to be swept up in his enthusiasm as he waxed eloquently about this twisty path to discovery or that sinewy bit of logic, and the fact that I have such vivid memories of his lectures decades later speaks to his artistry.

  10. Are managers also ‘crafting leaders’? The link between organizational rank, autonomy, and job crafting

    OpenAIRE

    Roczniewska Marta Anna; Puchalska-Kamińska Malwina

    2017-01-01

    Although research has examined the role leaders may play in shaping job re-design behaviors among their subordinates, little is known about the way managers craft their jobs as compared to other employees. In two crosssectional studies we tested whether organizational rank affects the frequency of job crafting (H1), and to what extent this relationship is mediated via perceived autonomy (H2). Study 1 (N = 267) demonstrated that managers craft their jobs more frequently than non-managers by in...

  11. Re-crafting the culture: Crafting the gender statements through circumcision and belly dancer dresses

    OpenAIRE

    Akbulut, Dilek; Hocaoğlu, Dilek; Himam Er, Dilek

    2013-01-01

    Craft often carries an ideology suggesting a particular look. Craft is not simply about making, but about making political statement since the Industrial Revolution. It is often perceived inferior to art with its sensual, skill based, pastoral qualities used to introduce amateur forms. Although craft is taken to mean an object having a high degree of handmade input, it does not necessarily require being produced or designed using traditional materials, produced as a one-off or as part of a sm...

  12. DEVELOPMENT OF INTERACTIVE MULTIMEDIA COURSEWARE (E-CRAFT FOR CRAFT EDUCATION

    Directory of Open Access Journals (Sweden)

    Salyani OSMAN,

    2012-08-01

    Full Text Available The way of teaching and learning traditional crafts have always used traditional apprenticeship learning methods where the expert facilitates transfer of practice skill sets to novices. As a craft has been taught in conventional approach, the students and experts have been facing several problems especially when expert needs to teach a group of students. An appropriate mapping of craft education and Information and Communication Technologies using Multimedia technology for instance, has the potential in transforming traditional craft learning into more flexible environment. This paper reports on a research project on development of an interactive multimedia courseware package for teaching and learning traditional craft called e-CRAFT. The e-CRAFT is specially designed for songket weaving course taught to certificate and diploma students from Fakulti Seni Kraf Tenunan in their first year study at Institut Kraf Negara, Malaysia (National Craft Institute. The courseware was developed in a web-based environment and overall development process was based on the Dick and Carey's process model and conceptual Instructional Design framework. It is made up of eight learning modules: Introduction, Materials & Tools, Knowing Motifs, Learn How to Weave, Quizzes & Test, Online Discussion, Glossary and Help module. In order to test whether the courseware is suitable in terms of usability, pilot testing was done to a sample of 10 students. The results from pilot test received positive feedback which signifies the courseware is considered acceptable for effectiveness study and help for further improve of the e-CRAFT courseware.

  13. Fungal decay of traditional fishing craft

    Digital Repository Service at National Institute of Oceanography (India)

    Gupta, R.

    , their role in the biodeterioration process, traditional and modern preventive methods, their economics with suggestions for future work. This study becomes important in view of the fishing industry turning towards traditional fishing craft for low energy...

  14. Can Niche Agriculturalists Take Notes from the Craft Beer Industry?

    OpenAIRE

    Woolverton, Andrea E.; Parcell, Joseph L.

    2008-01-01

    This industry-level case study focuses on the growth cycles of craft brewing, a niche industry. The research case is defined as the craft beer industry evolution including the surrounding institutional and consumer environments. The research goal is to provide insight for niche agriculturalists by examining the case of the successful niche craft beer industry. First, the environment surrounding craft beer reemergence is analyzed. We examine the current state of the craft beer industry with a ...

  15. Modern electrical installation for craft students

    CERN Document Server

    Scaddan, Brian

    2013-01-01

    Modern Electrical Installation for Craft Students, Volume 2, Third Edition discusses several topics concerning electrical installations. The book is comprised of eight chapters that deal with craft theory, associated subjects, and electrical industries. Chapter 1 covers inductors and inductance, while Chapter 2 tackles capacitors and capacitance. Chapter 3 deals with inductance and capacitance in installation work. The book also discusses cells, batteries, and transformers. The electrical industries, control and earthing, and testing are also dealt with. The last chapter discusses the basic el

  16. Sustainable Innovation of Glass Design and Craft

    OpenAIRE

    Sparre-Petersen, Maria

    2014-01-01

    Barely any research has been made into the implementation of sustainable principles in glass design and craft. A common tendency among students and practitioners is to consider it problematic if not impossible to develop a “truly sustainable practice”. Generally glass crafts people and glass designers aim to explore new aesthetic possibilities for the material and see sustainability as a hindrance for aesthetic freedom.On the contrary the field of design has strong and growing emphasis on sus...

  17. Employees' Perceived Opportunities to Craft and In-Role Performance: The Mediating Role of Job Crafting and Work Engagement.

    Science.gov (United States)

    van Wingerden, Jessica; Poell, Rob F

    2017-01-01

    The present study was designed to gain knowledge of the relationship between employees' perceived opportunities to craft, their actual job crafting behavior and, in line with JD-R theory, subsequently their work engagement and performance. Although scholars have suggested that employees' perceived opportunities to craft their job may predict their actual job crafting behavior, which may have consequences for their well-being and performance, no study has examined the relationships between these variables. We collected data among a heterogeneous group of Dutch employees (N = 2090). Participants of the study reported their perceived opportunities to craft, job crafting behavior, work engagement and performance. Results indicated that individuals who experience a high level of opportunities to craft reported higher levels of job crafting behavior. In turn, perceived opportunities to craft and job crafting behavior related to higher levels of work engagement and subsequently performance. We discuss the implications of these findings for theory and practice.

  18. Employees’ Perceived Opportunities to Craft and In-Role Performance: The Mediating Role of Job Crafting and Work Engagement

    Science.gov (United States)

    van Wingerden, Jessica; Poell, Rob F.

    2017-01-01

    The present study was designed to gain knowledge of the relationship between employees’ perceived opportunities to craft, their actual job crafting behavior and, in line with JD-R theory, subsequently their work engagement and performance. Although scholars have suggested that employees’ perceived opportunities to craft their job may predict their actual job crafting behavior, which may have consequences for their well-being and performance, no study has examined the relationships between these variables. We collected data among a heterogeneous group of Dutch employees (N = 2090). Participants of the study reported their perceived opportunities to craft, job crafting behavior, work engagement and performance. Results indicated that individuals who experience a high level of opportunities to craft reported higher levels of job crafting behavior. In turn, perceived opportunities to craft and job crafting behavior related to higher levels of work engagement and subsequently performance. We discuss the implications of these findings for theory and practice. PMID:29118729

  19. BioCraft: Using Gamification to Stimulate Students' Motivation and Acquisition of Scientific Terms in a Bilingual Classroom

    Science.gov (United States)

    Turner, Kent Alan

    Gamification is the act of introducing game elements in any aspect of life. In this case, it is a classroom. The operating model of BioCraft was a role-playing game that reinforced deaf students' use of new vocabulary in a gamified environment. BioCraft addressed the problem of deaf students acquiring scientific terms and using these scientific terms bilingually in academic language. BioCraft also established a student-centered learning atmosphere that promoted intersubjectivity, appropriation, and self-determination. In BioCraft, students became avatars of new organisms living on a new planet who needed to learn about living systems, adaptations, and genetics in order to survive. The results of the operating model suggested that gamification had an effect on deaf students' motivation and frequency of using new scientific terms with minimal persuasion from the teacher.

  20. 47 CFR 80.1095 - Survival craft equipment.

    Science.gov (United States)

    2010-10-01

    ....4 of the SOLAS Convention. (The SOLAS Convention can be purchased from International Maritime... forward and aft areas (see Regulation III/26.1.4 of the SOLAS Convention). Alternatively, one radar... SOLAS Convention. One of these radar transponders may be radar transponder required by § 80.1085(a)(3...

  1. 46 CFR 180.175 - Survival craft equipment.

    Science.gov (United States)

    2010-10-01

    ... liferafts. Each inflatable liferaft must have one of the following equipment packs as shown by the markings on its container: (1) Safety of Life at Sea (SOLAS) B Pack; or (2) SOLAS A Pack. (c) Inflatable...

  2. 46 CFR 117.175 - Survival craft equipment.

    Science.gov (United States)

    2010-10-01

    ... inflatable liferaft must have one of the following equipment packs as shown by the markings on its container: (1) Safety of Life at Sea (SOLAS) B Pack; or (2) SOLAS A Pack. (c) Inflatable buoyant apparatus. Each...

  3. The nature of creativity in craft

    DEFF Research Database (Denmark)

    Glaveanu, Vlad Petre

    2012-01-01

    The present article explores the nature of creativity in craft and does so with the help of a case study of traditional Easter egg decoration. It starts by positioning the domain of folk art in relation to fine art and within a larger category of everyday life forms of creative expression......, internalisation, and social interaction aspects, which are discussed in turn. Findings reveal fundamental features of craft such as its materiality, the presence of a strong traditional background, the importance of continuous learning, and the role of family and community relations. Towards the end, connections...... are made with the existing literature and final reflections offered on whether the characteristics above say something about creativity more generally, beyond the context of craft....

  4. From Gender-segregated Subjects to Multi-material Craft: Craft Student Teachers’Views on the Future of the Craft Subject

    Directory of Open Access Journals (Sweden)

    Jaana Lepistö

    2015-12-01

    Full Text Available This paper describes the views of student teachers of craft about the future of craft as a school subject. The study was conducted at the University of Turku, Department of Teacher Education, in Rauma in 2014. The literature review revealed that the subject of craft in Finnish basic education is understood as a dialog between the maker and the materials. However, teaching and learning craft in schools and in teacher education has a strong gender-based tradition. The aim of this study is to investigate student teachers’ understanding of craft as a school subject in the future and their solutions to teaching craft in basic education. The data were collected from essays (N = 20 written by student teachers of craft. The essays were analyzed qualitatively using content analysis. The results showed that the student teachers of craft viewed holistic craft, reflective action readiness, entrepreneurial behaviour, multiple skills, the use of versatile materials, and craft as sources of pleasure and the main solutions for the future of craft as a subject.

  5. Crafting culture : artisan cooperatives in Oaxaca, Mexico

    OpenAIRE

    Edwards, Meghan E.

    2009-01-01

    As the cultural tourism industry expands in Mexico, the implications for Oaxacan artisans and their crafts are far -reaching. The economic crises of the 1980s and early 1990s led to a renewed push by the government to promote tourism and a state-sponsored idea of mexicanidad, which has resulted in the increased commercialization of crafts. This project focuses on artesanías within the framework of cultural tourism in order to examine the ways in which lo mexicano is packaged for tourist consu...

  6. Friedel-Crafts Acylation with Amides

    Science.gov (United States)

    Raja, Erum K.; DeSchepper, Daniel J.; Nilsson Lill, Sten O.; Klumpp, Douglas A.

    2012-01-01

    Friedel-Crafts acylation has been known since the 1870s and it is an important organic synthetic reaction leading to aromatic ketone products. Friedel-Crafts acylation is usually done with carboxylic acid chlorides or anhydrides while amides are generally not useful substrates in these reactions. Despite being the least reactive carboxylic acid derivative, we have found a series of amides capable of providing aromatic ketones in good yields (55–96%, 17 examples). We propose a mechanism involving diminished C-N resonance through superelectrophilic activation and subsequent cleavage to acyl cations. PMID:22690740

  7. 33 CFR 401.58 - Pleasure craft scheduling.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Pleasure craft scheduling. 401.58... OF TRANSPORTATION SEAWAY REGULATIONS AND RULES Regulations Seaway Navigation § 401.58 Pleasure craft scheduling. (a) The transit of pleasure craft shall be scheduled by the traffic controller or the officer in...

  8. Employees' perceived opportunities to craft and in-role performance: The mediating role of job crafting and work engagement

    National Research Council Canada - National Science Library

    Van Wingerden, Jessica; Poell, Rob F

    2017-01-01

    ..., subsequently their work engagement and performance. Although scholars have suggested that employees' perceived opportunities to craft their job may predict their actual job crafting behavior, which may have consequences for their well...

  9. Are managers also ‘crafting leaders’? The link between organizational rank, autonomy, and job crafting

    National Research Council Canada - National Science Library

    Marta Anna Roczniewska; Malwina Puchalska-Kamińska

    2017-01-01

    Although research has examined the role leaders may play in shaping job re-design behaviors among their subordinates, little is known about the way managers craft their jobs as compared to other employees...

  10. Textbooks as crafted representational objects: A comparative ...

    African Journals Online (AJOL)

    Textbooks as crafted representational objects: A comparative analysis of Grade 7 home language textbooks for isiZulu, Sepedi, Sesotho, Afrikaans and English. ... in each one, in the mediation strategies selected and in the subject positions that each design team offers to learners as adolescent local and global citizens.

  11. SMALL CRAFT OPERATION AND NAVIGATION, INSTRUCTOR'S GUIDE.

    Science.gov (United States)

    Louisiana State Dept. of Education, Baton Rouge.

    THE MATERIAL IN THIS COURSE IN MARINE NAVIGATION AND SMALL CRAFT OPERATION ON INLAND AND INTERNATIONAL WATERS WAS DEVELOPED BY AN INDIVIDUAL AUTHOR FOR USE IN TRADE SCHOOL PREPARATORY AND EXTENSION CLASSES FOR MALE ADULTS WHO PLAN TO OPERATE BOATS. THE OBJECTIVE IS TO PREPARE THE SMALL BOAT OPERATOR FOR HIS OWN CONTINUATION IN THE STUDY OF…

  12. Crafts-Artists in the United States.

    Science.gov (United States)

    Cerf, J. George; And Others

    Following a preliminary study of crafts membership organizations in the United States, a survey was conducted of members of these organizations in order to determine their number, kind, media of work, personal characteristics, and geographic location. A sample of 5,146 craftspersons who were members of these organizations was mailed a…

  13. The Art and Craft of Science

    Science.gov (United States)

    Root-Bernstein, Robert; Root-Bernstein, Michele

    2013-01-01

    Walter Alvarez, a doctor and physiologist of some renown, decided to send his scientifically talented son, Luis, to an arts and crafts school where Luis took industrial drawing and woodworking instead of calculus. Luis Alvarez won the Nobel Prize in physics in 1968. Einstein was certainly not a standout in his mathematics and physics classes. Yet…

  14. HYDRODYNAMIC PERFORMANCES OF SMALL SIZE SWATH CRAFT

    Directory of Open Access Journals (Sweden)

    Ermina Begovic

    2015-12-01

    Full Text Available The good seakeeping characteristics of SWATH hull form are very interesting for small working craft and pleasure boats. Intrinsic limitations as the low values of weight per inch of immersion and transversal and longitudinal instability, can be acceptable and successfully managed when the mission profile does not ask for significant load variation and shift. The exploitation of SWATH concept is limited by the craft size, but if main dimensions allow enough static stability, this configuration appears very promising. SWATH behaviour in rough sea at zero and low speed have led to consider this hull form within the small craft design research program in progress at University of Naples Federico II. The design of small size SWATH working/pleasure craft has to begin from the consideration of strut waterplane areas that are the key factor to get acceptable static and dynamic stability. Displacement has to be reduced as most as possible to increase static stability, as shown by last design trends. The results of CFD analysis concerning SWATH resistance and propulsion, aspects are presented. A numerical evaluation of the hull-propeller interactions is performed, through simulations of self-propulsion tests with a simplified method (Actuator Disk model to discretize the propeller effect. The effective wake coefficient, the thrust deduction fraction and hull efficiency are provided. To validate CFD resistance results a comparison with experimental tests performed by Authors is reported. The presented work highlights different hydrodynamic aspects, comments advantages and critical issues of SWATH concept and reports detailed CFD modelling procedure with the aim to provide a reference for SWATH small craft design.

  15. Digital Crafting in the field of Ceramics

    DEFF Research Database (Denmark)

    Hansen, Flemming Tvede; Evers, Henrik Leander; Tamke, Martin

    2015-01-01

    This article aims to discuss and explore how craft knowledge in the field of ceramics can be utilized through digital technologies. Based on a set of experiments, which led to the development of a computational system that negotiates between the movement of the designer’s hands and the 3d clay...... custom digital design tools are developed and the way craftsmen in the field of ceramics are developing their material and tools for the making of ceramics. The communalities are especially centred on the experimental approach, pursued by both fields. Reflecting on these positions through our own work we...... identify different modes of experimenting, which are useful to drive design development and to develop the concept of digital crafting in the fields of ceramics. We explore how novel digital means can be utilized for a parametric setup that directly informs ornamentation through bodily engagement...

  16. Sustainable Innovation of Glass Design and Craft

    DEFF Research Database (Denmark)

    Sparre-Petersen, Maria

    2014-01-01

    innovation within the creative practices of glass design and craft. The paper will consist of an exploration of how introduction of sustainable principles may serve as a catalyst for aesthetic innovation in a process of experimentation with materials end techniques. A workshop for students of glass......, reduction of production and transportation of new glass is desirable (Environmental Protection Agency, 2012), and can be realized by recycling glass, that has already been manufactured, used and collected for recycling, but has ended up in landfills due to the market mechanisms that allow manufacturing...... and deposition of glass is reduced Today glass production predominantly consists of window glass, glass wool for insulation and containers such as bottles and jelly jars. Glass craft and design hold only a fraction of the market. Still there is reason to believe that generation and implementation of new...

  17. Improving user experience in StateCraft

    OpenAIRE

    Carlson, Christoph Mandler; Hellevang, Mathias

    2010-01-01

    User experience is an important aspect of game development, and techniques in Artificial Intelligence have been proved to increase the agent performance and have the potential to affect user experience in games. In this thesis, we aim to improve the user experience of the computer game known as StateCraft by extending the computer controlled opponent with the Emotion module and the Prisoner's Dilemma module. We conducted simulations and user tests to study the effects of these modules on the ...

  18. Concept annotation in the CRAFT corpus

    Directory of Open Access Journals (Sweden)

    Bada Michael

    2012-07-01

    Full Text Available Abstract Background Manually annotated corpora are critical for the training and evaluation of automated methods to identify concepts in biomedical text. Results This paper presents the concept annotations of the Colorado Richly Annotated Full-Text (CRAFT Corpus, a collection of 97 full-length, open-access biomedical journal articles that have been annotated both semantically and syntactically to serve as a research resource for the biomedical natural-language-processing (NLP community. CRAFT identifies all mentions of nearly all concepts from nine prominent biomedical ontologies and terminologies: the Cell Type Ontology, the Chemical Entities of Biological Interest ontology, the NCBI Taxonomy, the Protein Ontology, the Sequence Ontology, the entries of the Entrez Gene database, and the three subontologies of the Gene Ontology. The first public release includes the annotations for 67 of the 97 articles, reserving two sets of 15 articles for future text-mining competitions (after which these too will be released. Concept annotations were created based on a single set of guidelines, which has enabled us to achieve consistently high interannotator agreement. Conclusions As the initial 67-article release contains more than 560,000 tokens (and the full set more than 790,000 tokens, our corpus is among the largest gold-standard annotated biomedical corpora. Unlike most others, the journal articles that comprise the corpus are drawn from diverse biomedical disciplines and are marked up in their entirety. Additionally, with a concept-annotation count of nearly 100,000 in the 67-article subset (and more than 140,000 in the full collection, the scale of conceptual markup is also among the largest of comparable corpora. The concept annotations of the CRAFT Corpus have the potential to significantly advance biomedical text mining by providing a high-quality gold standard for NLP systems. The corpus, annotation guidelines, and other associated resources are

  19. Crafted - meisterdatud / Mihkel Tüür

    Index Scriptorium Estoniae

    Tüür, Mihkel, 1976-

    2012-01-01

    12. Alvar Aalto sümpoosion Jyväskyläs 10.-12. augustil 2012 teemal "Crafted". Kuraator Pekka Heikkinen. Pikemalt Mohsen Mostafavi ettekandest "Arhitektuur on materiaalne" ja Jürg Conzetti ettekandest "Strukturaalse tava jätkamine". Autori sõnul jäi kõlama mõte, et meisterlikult ehitatud maja saab olla ainus arhitektuuri tegelik mõõde

  20. Catalytic Friedel-Crafts reaction of aminocyclopropanes.

    Science.gov (United States)

    de Nanteuil, Florian; Loup, Joachim; Waser, Jérôme

    2013-07-19

    A Lewis acid catalyzed Friedel-Crafts reaction between donor-acceptor aminocyclopropanes and indoles and other electron-rich aromatic compounds is reported. Indole alkylation at the C3 position was generally obtained for a broad range of functional groups and substitution patterns. In the case of C3-substituted indoles, C2 alkylation was observed. The reaction gives a rapid access to gamma amino acid derivatives present in numerous bioactive molecules.

  1. Are managers also ‘crafting leaders’? The link between organizational rank, autonomy, and job crafting

    Directory of Open Access Journals (Sweden)

    Roczniewska Marta Anna

    2017-06-01

    Full Text Available Although research has examined the role leaders may play in shaping job re-design behaviors among their subordinates, little is known about the way managers craft their jobs as compared to other employees. In two crosssectional studies we tested whether organizational rank affects the frequency of job crafting (H1, and to what extent this relationship is mediated via perceived autonomy (H2. Study 1 (N = 267 demonstrated that managers craft their jobs more frequently than non-managers by increasing structural job resources and seeking challenges at work. We also showed that autonomy explains the relationship between organizational rank and the frequency of increasing structural and social job demands, as well as seeking challenges. However, managers did not craft their jobs by decreasing job demands more often than regular employees. In Study 2 (N = 262 we replicated this pattern of results, subsequently demonstrating that managers with shorter tenure use their autonomy to craft their jobs via decreasing job demands. We discuss the contributions and potential implications of these results.

  2. NATURAL BASES AND ARTISTIC MEANS OF MODERN ARTS AND CRAFTS OF DAGESTAN

    Directory of Open Access Journals (Sweden)

    G. G. Gazimagomedov

    2015-01-01

    Full Text Available The aim is to carry out a generalized analysis of the history of formation of a new artistic language in contemporary arts and crafts of Dagestan. An innovative search for applied artist has gained further development in a series of works of the leading masters of folk arts and crafts of Dagestan. Discussion. For millennia, arts and crafts of Dagestan have been organically linked with the life of people and their everyday way of life and daily activities, with their worldview and understanding of beauty. In the middle of the 1st millennium BC in the mountainous Dagestan, art of bronze casting has reached a high degree of perfection, most vividly represented by statues of different wild and domestic animals. Images of animals are interpreted generically, without study of small details, but with the characteristic features of the exterior. Paired images of birds are often found in the arts and crafts of the medieval Dagestan. This heraldic composition, two-part or in conjunction with the sacred tree - a three-part, presented in metal-plastic and carved stone and wood, was one of the most popular and enduring decorative items that was common during the Middle Ages and has survived to the present day. This also has been further developed and improved and inherited by craftsmen of Dagestan.Conclusion. When creating works of arts and crafts craftsmen use diverse traditional arts and engineering techniques, the ancient but substantially revised and reinterpreted iconic scenes and ornamental motifs. In art, folk craftsmen emphasize the unity of man and nature. Most ornamental motifs common in Dagestan, go back to the very specific nature prototypes. Compositional structure, as the artistic analysis shows, is often borrowed from nature. This feeling becomes a condition for cultural and biological development, acting as a factor of co-evolution of man and nature.

  3. Leading to Crafting: The Relation Between Leadership Perception and Nurses' Job Crafting.

    Science.gov (United States)

    Esteves, Tiago; Pereira Lopes, Miguel

    2017-06-01

    Whenever individuals adapt their jobs to make them closer of their personal preferences, they are performing job crafting. This study aims to investigate if the way nurses perceive their leaders' behaviors is related with job crafting development. To do so, a quantitative analysis was conducted among a group of 325 Portuguese nurses. Results indicate that the perception of an empowering leader was found to be strongly related with the increase of challenges in the work environment, and with the development of stronger relations with direct managers and co-workers, which are two job crafting dimensions. The perception of a directive leader was found to be positively related with the avoidance of performing hindering tasks. Strengthening relations with direct managers and co-workers was found to be particularly related to leadership perception. Theoretical and practical implications are discussed.

  4. Unknown unknowns: knowledge elicitation for multimedia in craft learning

    OpenAIRE

    Wood, N.

    2004-01-01

    Craft skills were originally taught through apprenticeship, a time consuming process both for teacher and learner in a situation which discouraged innovation and development. New technologies offer the opportunity for learners to draw upon the skills of experienced craft practitioners whilst still directing their own learning at a pace and style that suits their craft practice.\\ud In my previous research (Wood 2003) I considered the design of multimedia to support learning of tacit knowledge;...

  5. Diverse orientations in craft education: Student teachers’ conceptions and perceptions

    Directory of Open Access Journals (Sweden)

    Tarja Kröger

    2016-03-01

    Full Text Available Craft education in Finland has been in a state of change. The concept of a holistic craft process was implemented in the National Core Curriculum in 2004 and the new Curriculum from 2014 strengthened it. Craft and holistic craft is not one unity but includes several orientations. This study aims to research student teachers’ conceptions and perceptions about diverse orientations and the necessity of craft education before they begin their studies in craft pedagogy. Given that the beliefs that student teachers bring to professional learning play a pivotal role in influencing what they can learn from teacher education, they are a subject worthy of investigation. The data consists of on‐line questionnaire answers by student teachers (N=113 at the University of Finland in teacher education in 2014. The on-line questionnaire was answered at the beginning of a basic course in textile craft education at an early stage of their teacher studies. Findings suggest that student teachers conceive of craft education primarily as model-oriented and skill-oriented rather than design-oriented and expression-oriented. Student teachers think that craft education is needed at school, but explanations are not very diverse. The findings of this study can be useful in the process of developing teacher education programmes.

  6. Crafting the change: the role of job crafting and regulatory focus in adaptation to organizational change

    NARCIS (Netherlands)

    Petrou, P.

    2013-01-01

    Background Organizations change rapidly nowadays. However, little is known about successful ways in which employees can adapt to the new situation that arises throughout organizational change. The present dissertation addressed job crafting as a proactive employee strategy in order to deal with and

  7. Crafting your Career: How Career Competencies Relate to Career Success via Job Crafting

    NARCIS (Netherlands)

    Akkermans, J.; Tims, M.

    2017-01-01

    This study aimed to investigate whether career competencies could enhance an employee's subjective career success in terms of perceived employability and work-home balance via job crafting behaviors. Based on Job Demands-Resources (JD-R) Theory, we examined a potential motivational process in which

  8. Defense Utility of Commercial Vessels and Craft.

    Science.gov (United States)

    1980-01-01

    total U.S.-flag tug and barge fleet. Data are presented on ocean-classed tugs of 2,237 kW (3,000 brake horsepower) or more, and on ocean- clased barges of...Boston area. Previously, it was operated by the City of Miami, Florida. Future craft include two fireboats (HM2 Mark IV ), which are to be delivered in...STRENGTHENING (yes/no) No 23. MISCELLANEOUS FEATURES Some booms can be operated in fixedirnde AL iV 161 8 VEbSf-L ADAPTABILITh 24 CONVIRIIBILIIY Cr TANKS

  9. Crafts and Craft Education as Expressions of Cultural Heritage: Individual Experiences and Collective Values among an International Group of Women University Students

    Science.gov (United States)

    Kokko, Sirpa; Dillon, Patrick

    2011-01-01

    This paper explores relationships between crafts, craft education and cultural heritage as reflected in the individual experiences and collective values of fifteen female university students of different nationalities. The students (all trainee teachers) were following a course in crafts and craft education as part of an International Study…

  10. Masters and Apprentices of Textile Craft

    Directory of Open Access Journals (Sweden)

    Annelie Holmberg

    2013-10-01

    Full Text Available This article describes how the craftsmen at the workroom at Handarbetets vänner, Stockholm, learned their craft skills during the years 1948‒2012. What this knowledge consisted of and how the apprentices’ knowledge grows into skillfulness. Interviews with 15 weavers and embroiderers who have worked during the time period form the empirical material. The period of time was chosen according to the informants´ times of employment.The strategies for learning are affected by dialogue between the craftsmen, both a verbal and a silent dialogue. The dialogue is an important part of the learning even though the making is central. The workroom forms its own way of making textile art, a way of doing that is learned from master to apprentice. In this situated knowledge, the different masters have their own ways of for instance mixing color and material, all corresponding with core values. The learning is also affected by the artistic leader and the artist.The learning within the workroom occurs in the making of objects, but never at the cost of the quality of the objects. The core values of the establishments, and the fact that there is a strive to be profitable, makes the circumstances. The collaboration with the artist in creating unique textile art is the primary goal; the learning is something that is taken for granted in order to withhold the competence in the establishment.Keywords: textile craft, master and apprentice, craftsmen, textile art, workroom

  11. Sarawak Bamboo Craft: Symbolism and Phenomenon

    Directory of Open Access Journals (Sweden)

    Arshad Mohd Zaihidee

    2014-04-01

    Full Text Available The relationship between human beings and their environment has stirred reactions between nature and the development of mind and actions that can be discussed using interdisciplinary approaches such as psychology, sociology, anthropology and history, in understanding human thinking and behavior. A psychological approach is intended to evaluate the individual choices and needs in society. A sociological approach details the various patterns in the social organization. An anthropological approach is tied with culture and belief to fulfil human needs which are based on their habitat, while a historical approach looks at the development which is related to the past. Dimensions of experiences, order and logic, selective elaboration and expressions are used to analyze the bamboo craft of Iban, Melanau and Bidayuh societies in Sarawak long-houses. The existence of constitutive, moral, expressive and cognitive symbols has been interpreted based on a theoretical framework that has been developed by Langer Art Theory, Parsons Social Theory and Kaplan Culture Theory. The values and meaning formed are interpreted to understand matters related to the lives of villagers and the finding suggests that bamboo craft expresses the multi-ethnic mind and character in the socio-culture of long- houses in Sarawak.

  12. Crafting usable knowledge for sustainable development.

    Science.gov (United States)

    Clark, William C; van Kerkhoff, Lorrae; Lebel, Louis; Gallopin, Gilberto C

    2016-04-26

    This paper distills core lessons about how researchers (scientists, engineers, planners, etc.) interested in promoting sustainable development can increase the likelihood of producing usable knowledge. We draw the lessons from both practical experience in diverse contexts around the world and from scholarly advances in understanding the relationships between science and society. Many of these lessons will be familiar to those with experience in crafting knowledge to support action for sustainable development. However, few are included in the formal training of researchers. As a result, when scientists and engineers first venture out of the laboratory or library with the goal of linking their knowledge with action, the outcome has often been ineffectiveness and disillusionment. We therefore articulate here a core set of lessons that we believe should become part of the basic training for researchers interested in crafting usable knowledge for sustainable development. These lessons entail at least four things researchers should know, and four things they should do. The knowing lessons involve understanding the coproduction relationships through which knowledge making and decision making shape one another in social-environmental systems. We highlight the lessons that emerge from examining those coproduction relationships through the ICAP lens, viewing them from the perspectives of Innovation systems, Complex systems, Adaptive systems, and Political systems. The doing lessons involve improving the capacity of the research community to put its understanding of coproduction into practice. We highlight steps through which researchers can help build capacities for stakeholder collaboration, social learning, knowledge governance, and researcher training.

  13. Students' Attitudes towards Craft and Technology in Iceland and Finland

    Science.gov (United States)

    Thorsteinsson, Gísli; Ólafsson, Brynjar; Autio, Ossi

    2012-01-01

    Craft education in both Finland and Iceland originated over 140 years ago and was influenced by the Scandinavian Sloyd pedagogy. Since then, the subject has moved away from craft and towards technology, with the aim being to increase students' technological abilities. In the beginning, the subject largely focused on the students copying artefacts,…

  14. Craft Training in Russia: Theory and Practice of Development

    Science.gov (United States)

    Romantsev, Gennadij M.; Efanov, Andrei V.; Moiseev, Andrei V.; Bychkova, Ekaterina Yu.; Karpova, Natalia P.; Tidemann, Bruno

    2016-01-01

    The relevance of the research topic is substantiated by the social commitment to the establishment of a system of craft training focused on training personnel for craft enterprises. The purpose of the article is to provide theoretical and methodological substantiation of the necessity to provide organizational and pedagogical foundations for the…

  15. Construction and validation of the perceived opportunity to craft scale

    NARCIS (Netherlands)

    J. Van Wingerden (Jessica); Niks, I.M.W. (Irene M.W.)

    2017-01-01

    textabstractWe developed and validated a scale to measure employees' perceived opportunity to craft (POC) in two separate studies conducted in the Netherlands (total N = 2329). POC is defined as employees' perception of their opportunity to craft their job. In Study 1, the perceived opportunity to

  16. Cloth Crafts of India: Cotton and Silk, Trade and History.

    Science.gov (United States)

    Mueller, Peggy; Turkovich, Marilyn

    This resource suggests that to study India without experiencing the life of the people as represented through their folk craft traditions would be a hollow venture. History and geography are conveyed in the symbols and figures that decorate Indian crafts. Basic beliefs, ancient symbols, and religious traditions are conveyed in recurring visual…

  17. Formation control of marine surface craft: a Lagrangian approach

    DEFF Research Database (Denmark)

    Ihle, Ivar-Andre F.; Jouffroy, Jerome; Fossen, Thor I.

    2006-01-01

    This paper presents a method for formation control of marine surface craft inspired by Lagrangian mechanics. The desired formation configuration and response of the marine surface craft are given as a set of constraints in analytical mechanics. Thus, constraints forces arise and feedback from...

  18. Craft-Art as a Basis for Human Activity

    Science.gov (United States)

    Karppinen, Seija

    2008-01-01

    This article based on my doctoral thesis examines the Basic Arts Education system in Finland, focusing on Basic Crafts Education and its description through action concepts. The main task of the study was to create a concept model. In the first part of the study a concept map was created from the practice of Basic Crafts Education. The aim of the…

  19. Searching the Soul: Veterans and Their Arts and Crafts

    Science.gov (United States)

    Hasio, Cindy

    2011-01-01

    For military veterans suffering from the long-term trauma of warfare, arts and crafts become much more than the fabrication of relics; they can literally save the spirit. Dialogue and interaction between the veterans, volunteers, and staff are crucial to the success of veterans' arts and crafts program. The purpose of this research was threefold.…

  20. Creating Chicago History: Making Outreach Craft Activities Meaningful

    Science.gov (United States)

    Karp, Madeline

    2012-01-01

    When it comes to having a traveling outreach activity for a museum, a craft can seem like the perfect solution. It can seemingly be all things at once--educational, quick and fun. But, if poorly constructed, crafts can also have serious fallbacks. Using the Chicago History Museum and the Millennium Park Family Fun Festival as a case study, this…

  1. Crafting Stories in Hermeneutic Phenomenology Research: A Methodological Device.

    Science.gov (United States)

    Crowther, Susan; Ironside, Pam; Spence, Deb; Smythe, Liz

    2017-05-01

    Hermeneutic phenomenology, as a methodology, is not fixed. Inherent in its enactment are contested areas of practice such as how interview data are used and reported. Using philosophical notions drawn from hermeneutic phenomenological literature, we argue that working with crafted stories is congruent with the philosophical underpinnings of this methodology. We consider how the practical ontic undertaking of story crafting from verbatim transcripts is integral with the interpretive process. We show how verbatim transcripts can be crafted into stories through examples taken from interview data. Our aim is to open dialogue with other hermeneutic phenomenological researchers and offer alternate possibilities to conventional ways of work with qualitative data. We argue that crafted stories can provide glimpses of phenomena that other forms of data analysis and presentation may leave hidden. We contend that crafted stories are an acceptable and trustworthy methodological device.

  2. Crafting minds and communities with Minecraft.

    Science.gov (United States)

    Riordan, Benjamin C; Scarf, Damian

    2016-01-01

    Minecraft is a first-person perspective video game in which players roam freely in a large three-dimensional environment. Players mine the landscape for minerals and use these minerals to create structures ( e.g., houses) and mould the landscape. But can Minecraft be used to craft communities and minds? In this opinion piece, we highlight the enormous potential of Minecraft for fostering social connectedness, collaboration, and its potential as an educational tool. We highlight the recent use of Minecraft to aid socialization in individuals with Autistic Spectrum Disorder (ASD) and promote civic engagement via the United Nations Human Settlement Program. We further provide novel links between Minecraft and recent on work on the role of social cures and community empowerment in enhancing mental health, wellbeing, and resilience.

  3. Unknown toxic exposures. Arts and crafts materials.

    Science.gov (United States)

    Grabo, T N

    1997-03-01

    1. Arts and crafts material containing toxic chemicals have been found to be hazardous to human health. 2. Artists/craftspersons, who also may be employed in industry, often are unaware or not adequately informed about the toxic nature of many art products. 3. The occupational health nurse is in a critical position to identify and monitor the worker exposed to toxic chemicals both in the workplace and at home/art studio. 4. Education about hazardous substances can prevent illness or injury. With expertise in public health, occupational health nurses are in a key position to provide community education about the dangers of toxic art materials to the general public and the health care community.

  4. Art and Craft education for sustainable development

    Directory of Open Access Journals (Sweden)

    Eva Lutnæs

    2017-12-01

    Full Text Available The Norwegian school subject Art and Crafts makes a lense for pupils into the world of object, buildings and pictures. It makes visual and material culture part of general education. The subject embodies problem solving in materials, aesthetical awareness and critical reflection on visual communication and the quality of objects. Teachers in this subject have the opportunity to connect daily actions and opinions to bigger picture thinking, by challenging pupils to take responsibility for what they do, and what they might choose to ignore. This article explores four entries to ecoliteracy in the repertoire of the subject: Problem solving in materials, aesthetic experiences, responsible product design and critical reflection. Ecoliteracy rely on both awareness and empowerment, and to coin the four entries in design assignments would better prepare pupils for a transition towards a more sustainable future.

  5. Job crafting: Towards a new model of individual job redesign

    Directory of Open Access Journals (Sweden)

    Maria Tims

    2010-12-01

    Full Text Available Orientation: For a long time, employees have been viewed as passive performers of their assigned job tasks. Recently, several scholars have argued that job design theory needs to address the influence of employees on their job designs.Research purpose: The purpose of the study was to fit job crafting in job design theory.Motivation for the study: The study was an attempt to shed more light on the types of proactive behaviours of individual employees at work. Moreover, we explored the concept of job crafting and its antecedents and consequences.Research design, approach and method: A literature study was conducted in which the focus was first on proactive behaviour of the employee and then on job crafting.Main findings: Job crafting can be seen as a specific form of proactive behaviour in which the employee initiates changes in the level of job demands and job resources. Job crafting may be facilitated by job and individual characteristics and may enable employees to fit their jobs to their personal knowledge, skills and abilities on the one hand and to their preferences and needs on the other hand.Practical/managerial implications: Job crafting may be a good way for employees to improve their work motivation and other positive work outcomes. Employees could be encouraged to exert more influence on their job characteristics.Contribution/value-add: This article describes a relatively new perspective on active job redesign by the individual, called job crafting, which has important implications for job design theories.

  6. Women, Craft and the Post Conflict Reconstruction of Kashmir

    OpenAIRE

    Raina, Neelam

    2009-01-01

    This thesis contributes towards the knowledge of post conflict crafts of Kashmir and the role women play in this sector. It proposes crafts to be a culturally relevant activity which could generate income for people living in Kashmir. It analyses the impact of the conflict on the crafts of Kashmir from the perspective of the craftspeople. The research is based on fieldwork conducted in Srinagar, Kashmir (2003-2006). Here craftsmen’s groups were studied and a craftswomen’s organisation – Z...

  7. Shipboard Training and Maintenance for Merchant Vessel Survival Equipment.

    Science.gov (United States)

    1979-10-01

    ventilating sytems, ard the operation of all safety equipment. (2) The preparation and launching of lifeboats and liferafts. (3) The extinction of fire. 5-8 (4...water; (2) cold conditions; (3) shark -infested waters; (ii) how 1,o riqht a capsized survival craft; (i) actions to be taken when aboard a survival

  8. Integrated Design of Semi-Displacement Patrol Crafts

    National Research Council Canada - National Science Library

    Gillespy, Andrew J

    2008-01-01

    ... of any one change on the entire system. The initial design of smaller patrol craft is especially difficult due to the lack of design tools able to deal with ships of small size operating in the semi-planing region...

  9. Guides crafting meaning and identity in a flexible working life

    DEFF Research Database (Denmark)

    Meged, Jane Widtfeldt

    2017-01-01

    Certified guides are exemplary, well-educated, self-employed, casual labourers in a liberal and competitive job market. Applying grounded theory, this exploratory study builds on in-depth qualitative interviews with Danish, Italian and French certified guides. Informed by the theory of job crafting...... and adding a critical perspective, we understand the guides’ agency, and how they craft scope, tasks and relations in order to sustain a positive self-image and a meaningful working life. Comparing certified guides’ job-crafting practices, we learn that guides are alike across the three countries......, and they perceive themselves as natural-born who engage in self-actualization. They thrive on connecting with tourists, whom they empower or enlighten, as they craft idealistic or social objectives. At the same time, the guides work in individual workspaces, and they adapt to a competitive labour market...

  10. A Systematic Case Study of the Course, Offshore Survival Systems Training, To Improve the Practice of Marine Survival Training.

    Science.gov (United States)

    Zambon, Franco

    A major applied research project evaluated the effectiveness of a novel course, Offshore Survival Systems Training. The major course outcome that was evaluated was the increase in frequency with which offshore personnel correctly launched the covered powered survival craft on offshore drilling rigs. The evaluation methodology included the 628…

  11. Accidents of surface effect ships and hydrofoil craft

    Energy Technology Data Exchange (ETDEWEB)

    Korotkin, I.M.

    1981-01-01

    The work describes 200 accidents and disasters of hovercraft and hydrofoil craft of the United States, Great Britain, France, and other fleets which occurred in the 1960s and 1970s as a result of capsizing, storm damage, collisions, fires, explosions, etc. The causes of the accidents, the functioning of various craft systems, and the actions of the crews are examined. Recommendations on the prevention of such accidents are discussed.

  12. Minimum Plate Thickness in High-Speed Craft

    DEFF Research Database (Denmark)

    Pedersen, Preben Terndrup; Zhang, Shengming

    1998-01-01

    The minimum plate thickness requirements specified by the classification societies for high-speed craft are supposed to ensure adequate resistance to impact loads such as collision with floating objects and objects falling on the deck. The paper presents analytical methods of describing such impact...... phenomena and proposes performance requirements instead of thickness requirements for hull panels in high-speed craft made of different building materials....

  13. Craft Beer in the US: A Production of Culture Perspective

    OpenAIRE

    Chapman, Nathaniel Gray

    2015-01-01

    In this dissertation I use the production of culture perspective as a lens to analyze the emergence of craft beer in the US. In doing so, I examine how the six facets of the production of culture perspective have both constrained and stimulated the production of craft beer in the US. The six facets of the production of culture perspective are: law and regulation, industry structure, organizational structure, markets, technology, and occupational careers. These six facets, in concert, allowed ...

  14. A health hazard assessment in school arts and crafts.

    Science.gov (United States)

    Lu, P C

    1992-01-01

    Unlike the cautious attitude being exercised toward generic chemicals, an off-guard behavior is often observed toward the same chemicals once they are recognized as a "common daily item." Students and instructors of arts and crafts classes alike are often unaware of the potential risks from exposure to some of the arts and crafts materials they use due to either the false security of "common daily item" or the lack of specific knowledge of the hazardous ingredients in those products. This unawareness of potential health hazards could lead to improper handling of these materials and result in unnecessary health risk during their use. A three-year study of college arts and crafts class students indicates a high incidence of allergic reactions among attending students for exposure of less than 70 hours within a period of 7 weeks. A self-evaluation method is developed to identify and minimize these health hazards associated with arts and crafts classes. This checklist of 15 pertinent parameters covers identifiable hazardous areas and situations in arts and crafts classrooms. Record keeping and promotion of student awareness are also addressed, so that instructors and students in an arts and crafts class can more readily recognize actual or potential hazards and act to prevent them.

  15. Detail in architecture: Between arts & crafts

    Science.gov (United States)

    Dulencin, Juraj

    2016-06-01

    Architectural detail represents an important part of architecture. Not only can it be used as an identifier of a specific building but at the same time enhances the experience of the realized project. Within it lie the signs of a great architect and clues to understanding his or her way of thinking. It is therefore the central topic of a seminar offered to architecture students at the Brno University of Technology. During the course of the semester-long class the students acquaint themselves with atypical architectural details of domestic and international architects by learning to read them, understand them and subsequently draw them by creating architectural blueprints. In other words, by general analysis of a detail the students learn theoretical thinking of its architect who, depending on the nature of the design, had to incorporate a variety of techniques and crafts. Students apply this analytical part to their own architectural detail design. The methodology of the seminar consists of experiential learning by project management and is complemented by a series of lectures discussing a diversity of details as well as materials and technologies required to implement it. The architectural detail design is also part of students' bachelors thesis, therefore, the realistic nature of their blueprints can be verified in the production process of its physical counterpart. Based on their own documentation the students choose the most suitable manufacturing process whether it is supplied by a specific technology or a craftsman. Students actively participate in the production and correct their design proposals in real scale with the actual material. A student, as a future architect, stands somewhere between a client and an artisan, materializes his or her idea and adjusts the manufacturing process so that the final detail fulfills aesthetic consistency and is in harmony with its initial concept. One of the very important aspects of the design is its economic cost, an

  16. Arts and Crafts Painting: The Political Agency of Things

    Directory of Open Access Journals (Sweden)

    Morna O'Neill

    2015-11-01

    Full Text Available Can there be such a thing as “Arts and Crafts” painting? This article will address that question by interrogating the points of connection between Pre-Raphaelite painting and the Arts and Crafts object. Taking its cue from William Morris’s reflection on the “English Pre-Raphaelite School” from 1891, this article examines the interplay between painting and design in both Pre-Raphaelite painting and the Arts and Crafts movement. It addresses the ways in which paintings depicted decorative art, as well as the aspiration of decorative art to the symbolic potential traditionally associated with painting. It is my contention that Pre-Raphaelite painting unleashed a radical possibility for decorative art: the Arts and Crafts belief in the political agency of things.

  17. T-Craft Seabase Ramp Loads Model Test Data Report

    Science.gov (United States)

    2010-12-01

    matrix of Table 1, the T-Craft model was tested in three different modes in the Tandem. These modes included 1) as a barge (with a Styrofoam block... plates of the T-Craft is presented in Figure 11. This figure details the airflow holes for each of the separate plates that make up the transverse...deck. 13 *oo 99.3 ^ 3 och tmaaa kolc -3.30 - Top Plate Details i •K’Ki i.UU «J0 NJD -99.37- -» 18.10 » 1 Fii7IX2:.5«l ?l <l 43 30

  18. Guides crafting meaning and identity in a flexible workinglife

    DEFF Research Database (Denmark)

    Meged, Jane Widtfeldt

    2017-01-01

    Certified guides are exemplary, well-educated, self-employed, casual labourers in a liberal and competitive job market. Applying grounded theory, this exploratory study builds on in-depth qualitative interviews with Danish, Italian and French certified guides. Informed by the theory of job crafting......, and they perceive themselves as natural-born who engage in self-actualization. They thrive on connecting with tourists, whom they empower or enlighten, as they craft idealistic or social objectives. At the same time, the guides work in individual workspaces, and they adapt to a competitive labour market...

  19. Arts and Crafts Painting: The Political Agency of Things

    OpenAIRE

    Morna O'Neill

    2015-01-01

    Can there be such a thing as “Arts and Crafts” painting? This article will address that question by interrogating the points of connection between Pre-Raphaelite painting and the Arts and Crafts object. Taking its cue from William Morris’s reflection on the “English Pre-Raphaelite School” from 1891, this article examines the interplay between painting and design in both Pre-Raphaelite painting and the Arts and Crafts movement. It addresses the ways in which paintings depicted decorative art, ...

  20. Marian Roberts, Developing the Craft of Mediation: Reflections on Theory and Practice

    Directory of Open Access Journals (Sweden)

    Ghislaine M. Lanteigne

    2008-10-01

    Full Text Available In Developing the Craft of Mediation, Marian Roberts proposes that mediation is akin to a craft with its focus on learning from experience and from others working in the field to develop and master knowledge and skills.

  1. Maneuverability Estimation of High-Speed Craft

    Science.gov (United States)

    2015-06-01

    predators and preys generate new tactics in order to find food and survive. Howland analyzed the optimal strategies for predator avoidance based on...Prey-Predator Interactions in a Pursuit Situation, from [23] C. CATCH/ESCAPE CONDITIONS AND GENERALIZED CIRCLE INTERSECTION POINTS Howland suggests...dynamic models,” J. Mar. Sci. Technol., vol. 7, pp. 79–88, 1999. [23] H. C. Howland , “Optimal strategies for predator avoidance: The relative

  2. Craft Beer Marketing. Do You Have to be First, Best, or Unique to Succeed?

    OpenAIRE

    Lahnalampi, Benjamin

    2016-01-01

    This thesis deals with the interplay of marketing and design in the craft brewing industry in Finland. The goal was to figure out what craft brewers do to successfully market their products. The thesis first explains that craft beer is different from generic beer in that it is uncompromising in its ingredients, special flavours, and sole focus on the beer rather than stock prices. Craft breweries use grassroots and guerrilla marketing tactics. They are heavily involved in social media marketi...

  3. Malleable Thought: The Role of Craft Thinking in Practice-Led Graphic Design

    Science.gov (United States)

    Ings, Welby

    2015-01-01

    This article considers the potential of craft processes as creative engagements in graphic design research. It initially discusses the uneasy history of craft within the discipline, then draws upon case studies undertaken by three established designers who, in their postgraduate theses, engaged with craft as a process of thinking. In doing so, the…

  4. Artisans, Architects, and Apprentices: Valuing the Craft of Teacher Education

    Science.gov (United States)

    Boyd Potter, Rachel

    2016-01-01

    In this article, Boyd Potter describes teacher education faculty as both artisans and architects. As artisans, it is not only their products that enrich us; it is the art of the craft itself that shapes their work. An artisan is valued for the creative endeavor, and not solely the masterpiece. Preparing a quality teacher is not easy work, while…

  5. Examining Teaching Practices in Design and Craft Education in Iceland

    Science.gov (United States)

    Thorsteinsson, Gisli; Olafsson, Brynjar

    2017-01-01

    This article reports a survey which aimed to examine the present situation in Design and Craft Education (D&C) in Iceland in terms of teachers' general standing and their teaching inside the Icelandic elementary schools. A questionnaire was sent to 170 D&C teachers in Icelandic elementary schools. The questionnaire was completed by 101…

  6. Professional Interventions as a State-Crafting Grammar

    DEFF Research Database (Denmark)

    Ydesen, Christian; Øland, Trine

    2015-01-01

    This article is written in connection with a joint research project which adopts a comparative outlook in investigating post-war Danish professional interventions aimed at immigrants. Specifically, these interventions are investigated as a state-crafting grammar. One project primarily focuses...

  7. Role of clay as catalyst in Friedel–Craft alkylation

    Indian Academy of Sciences (India)

    solid catalysts in a test Friedel–Craft alkylation reaction of benzyl chloride with toluene using differential scanning calorimeter (DSC) are reported. Product formation has been analysed by FTIR spectroscopy. The main objective of this work is to show how clay as a solid catalyst affects reaction rates and activation energies.

  8. Crafts, Boys, Ernest Thompson Seton, and the Woodcraft Movement

    Science.gov (United States)

    Chalmers, F. Graeme; Dancer, Andrea A.

    2008-01-01

    This article examines early influences on art education for boys (Chalmers & Dancer, 2007) in areas traditionally labeled as crafts. Under review is the work of Ernest Thompson Seton, artist, naturalist, storyteller, author, philosopher, crusader for and supporter of indigenous American Indian ways of knowing, and a co-founder of the Boy Scouts of…

  9. Ghanaian Craft Exporters in the Global Market: Binding and Missing ...

    African Journals Online (AJOL)

    Agribotix GCS 068

    demonstrates that the ability of small enterprises to develop ties with industry actors (locally and globally) offers ..... Artisans Ghana (ATAG), an official of the Ministry of Trade and Industry in charge of craft export promotion and .... in Brazil and Pakistan, where local firms operating in industrial clusters invested in productive.

  10. Crafting Creative Nonfiction: From Close Reading to Close Writing

    Science.gov (United States)

    Dollins, Cynthia A.

    2016-01-01

    A process writing project in a third-grade classroom explored the idea of using nonfiction mentor texts to assist students in writing their own creative informational texts about animals. By looking at author craft and structure during close reading activities with nonfiction Twin Texts, students were taught how to emulate these techniques in…

  11. Conceptualizing responsible innovation in craft villages in Vietnam

    NARCIS (Netherlands)

    Voeten, J.; de Haan, J.A.C.; Roome, N.; de Groot, G.A.; Nguyen Thi, Huong; van den Hoven, J.; Doorn, N.; Swierstra, T.; Koops, B.-J.; Romijn, H.

    2014-01-01

    Previous research by the authors has explored small-scale innovations in poor craft producers’ clusters in villages in the Red River Delta in northern Vietnam. Although these innovations resulted in value creation and increased incomes, they also often gave rise to negative environmental or social

  12. Supplementing income from farms with income from rural craft: The ...

    African Journals Online (AJOL)

    This study on supplementation of income from farm enterprises with income from craft (mat-weaving) was conducted in Uturu in Abia state, Nigeria. Primary objective was to compare farm income with income from non-farm activities, especially from mat weaving; and determine factors that influenced decisions to use income ...

  13. Bottom Raking Damage to High-Speed Craft

    DEFF Research Database (Denmark)

    Simonsen, Bo Cerup

    1998-01-01

    This paper presents a comparative study of the raking damage to high speed craft (HSC) and conventional ships. The analysis is based on a detailed theoretical model for the raking resistance of an assembled ship bottom structure and on the idea that the impact conditions for various ship types have...

  14. Effectiveness of a Volunteer-Led Crafts Group Intervention amongst ...

    African Journals Online (AJOL)

    The purpose of this study was to determine the effectiveness of a volunteer led crafts group intervention (VLCG) as an adjunct to antidepressant medication on mild to moderately depressed women. A quasi-experimental, non-equivalent, control group study was conducted in an urban, psychiatric clinic. Depression was ...

  15. Robust formation control of marine surface craft using Lagrange multipliers

    DEFF Research Database (Denmark)

    Ihle, Ivar-Andre F.; Jouffroy, Jerome; Fossen, Thor I.

    2006-01-01

    This paper presents a formation modelling scheme based on a set of inter-body constraint functions and Lagrangian multipliers. Formation control for a °eet of marine craft is achieved by stabilizing the auxiliary constraints such that the desired formation con¯guration appears. In the proposed...

  16. Arts, Crafts and Indigenous Industries in Nigeria | Yakubu | Journal ...

    African Journals Online (AJOL)

    The paper is illustrative of the cultural wealth of Nigeria in terms of arts and crafts. It provides a descriptive picture of the various characteristics of the genres in the past and present and in traditional as well as modern Nigerian communities. It functions within religious, intellectual, and socio-economic contexts. Hence ...

  17. Richard Nixon's "Pragmatic" Space Race: Metaphorically Crafting a National Identity.

    Science.gov (United States)

    Krug, Linda T.

    President Richard Nixon decided in 1970 to commission the construction of a fleet of reusable space shuttles. Nixon's rhetoric on the space shuttle program (examined here in the light of Kenneth Burke's theory of symbolic action) shows how a philosophy of pragmatism was crafted out of a philosophy of wonderment. That one cannot now remember…

  18. Teaching the Surgical Craft: Surgery Residents Perception of the ...

    African Journals Online (AJOL)

    These include concerns about time management (e.g., patient cancellation), availability of resources (e.g., equipment allocation), roles (e.g., responsibilities), patient safety and sterility (e.g., aseptic. Teaching the Surgical Craft: Surgery Residents. Perception of the Operating Theater Educational. Environment in a Tertiary ...

  19. Transferring PSM craft skills in a 2 hour session

    NARCIS (Netherlands)

    Zijderveld, E.J.A. van; Morill, N.; Shaw, D.; Belton, V.; Harvey, P.; Rouwette, E.

    2007-01-01

    Many of those involved in the Problem Structuring Methods (PSM) community have commented on the struggle that novices face in building the craft skills associated with conducting a PSM intervention. As part of this year's Operational Research Society Conference, we have three 2-hour practical

  20. Ghanaian Craft Exporters in the Global Market: Binding and Missing ...

    African Journals Online (AJOL)

    The strong positions of buyers and export agents in the craft value chain enable them to apply sanctions to extract compliance from the exporters whereas the weak position of the export vendors implies the lack of sanctioning authority over the rogue artisan subcontractors. The government's promotion programmes could ...

  1. D Digital Simulation of Minnan Temple Architecture CAISSON'S Craft Techniques

    Science.gov (United States)

    Lin, Y. C.; Wu, T. C.; Hsu, M. F.

    2013-07-01

    Caisson is one of the important representations of the Minnan (southern Fujian) temple architecture craft techniques and decorative aesthetics. The special component design and group building method present the architectural thinking and personal characteristics of great carpenters of Minnan temple architecture. In late Qing Dynasty, the appearance and style of caissons of famous temples in Taiwan apparently presented the building techniques of the great carpenters. However, as the years went by, the caisson design and craft techniques were not fully inherited, which has been a great loss of cultural assets. Accordingly, with the caisson of Fulong temple, a work by the well-known great carpenter in Tainan as an example, this study obtained the thinking principles of the original design and the design method at initial period of construction through interview records and the step of redrawing the "Tng-Ko" (traditional design, stakeout and construction tool). We obtained the 3D point cloud model of the caisson of Fulong temple using 3D laser scanning technology, and established the 3D digital model of each component of the caisson. Based on the caisson component procedure obtained from interview records, this study conducted the digital simulation of the caisson component to completely recode and present the caisson design, construction and completion procedure. This model of preserving the craft techniques for Minnan temple caisson by using digital technology makes specific contribution to the heritage of the craft techniques while providing an important reference for the digital preservation of human cultural assets.

  2. Arts and Crafts Painting: The Political Agency of Things

    National Research Council Canada - National Science Library

    O'Neill, Morna

    2015-01-01

    .... Taking its cue from William Morris’s reflection on the “English Pre-Raphaelite School” from 1891, this article examines the interplay between painting and design in both Pre-Raphaelite painting and the Arts and Crafts movement...

  3. Reading the Writer's Craft: The Hemingway Short Stories

    Science.gov (United States)

    Garrigues, Lisa

    2004-01-01

    The high school students who spent five weeks studying the style and craft of Ernest Hemingway experienced the power and plus points of apprenticeships. Several assignments that helped the high school juniors to analyze Hemingway's work on short stories and learn from this master craftsman are presented.

  4. The Validity of the School Assessment in the Craft Subject

    Directory of Open Access Journals (Sweden)

    Antti Hilmola

    2016-06-01

    Full Text Available In this research project, the validity of the school assessment is examined in the craft subject in Finland’s basic education. The criteria for the school assessment are based on the Finnish Na-tional Core Curriculum (FNCC in which the idea of the Entire Craft (EC is highlighted. How-ever, the discussion as to whether or not the school practice is based on the idea of EC, or whether the teachers are still focused on the technical details of products in reflecting on the pupils’ tool-handling skills, is still an ongoing debate. Learner-centred learning is implicated in EC since the pupils are expected to set goals for the implementation of their own ideating, plan-ning and constructing. And, finally, in such a process, the self-reflection of the implemented out-comes against the goals will take place.  Altogether 73 craft teachers from 59 upper level schools participated in this research project. The pupils’ (N = 982 success was assessed during an EC period using the indicator validated by the previous nation-wide evaluation by the Finn-ish National Board of Education (FNBE. Since the valid school assessment was expected to reflect the success in the Entire Craft Assessment Period (ECAP, the outcomes were assessed against the criteria of the FNCC and compared to the pupils’ school scores. The data was ana-lysed using the Linear Regression Analysis (Enter Method. The central observation was that the pupils’ success in the criteria of the EC do not reflect the 7th grade school scores, in all re-spects. Moreover, the pupils’ success does not reflect the 6th grade school scores. The instruc-tions and supplementary education of the FNCC criteria are needed for craft teachers, especial-ly for class teachers at the lower level. In Finland, also the craft subject is taught by the class teachers at the lower level while, at the upper level, the subject teachers take their place. Ac-cording to the new FNCC, the number of class lessons will be

  5. Job crafting in schools for special education: A qualitative analysis [Job crafting in het speciaal onderwijs: Een kwalitatieve analyse

    NARCIS (Netherlands)

    Wingerden, J. van; Derks, D.; Bakker, A.B.; Dorenbosch, L.

    2013-01-01

    In this article we discuss the design and qualitative (process) evaluation of a job crafting intervention among employees at three Dutch schools for special education. In a period of 1.5 months, fifty employees participated in a group-based training intervention that addressed individual's job

  6. Categorizing the meanings of craft: A multi-perspectival framework for eight interrelated meaning categories

    Directory of Open Access Journals (Sweden)

    Anna Kouhia

    2012-09-01

    Full Text Available The meaning and value of crafts as bearers of the cultural heritage are widely acknowledged, and deserved attention has also been paid to the pedagogical applications of craft in practice. Still, research relating to subjectively interpreted meanings of crafts has remained rather scarce. The main interest of the study is to examine subjectively construed meanings of craft associated both to the self-reflective act of making and to the tangible craft object, and categorize the discovered meanings into representative categories. In presenting a multi-perspectival framework for the categories that portray the common kinds of meanings that crafts have, a substance that surpasses cultural boundaries is also captured due to the multicultural research setting. The primary empirical data of the study are composed of interviews of six women from different cultural backgrounds; the supporting data feature a participant observation of a multicultural craft activity group and photographic notes. The wide range of different meanings captured from the data is, during the conducted qualitative content analysis, critically classified into representational categories that typify the personally experienced meanings. The analysis revealed eight interrelated meaning categories regarding the meanings of craft that go beyond cultural boundaries: Meanings proceed from the subjective process of interpreting craft in a socially constructed, personalized setting, but still the meanings given to craft have been given similar characterizations in the several cultural contexts examined. This study adds to an understanding of how personalized meanings contribute to building intercultural reciprocity. Keywords: craft, culture, meanings, interculturality, meaning making

  7. O activismo estético feminista de Nikki Craft Nikki Craft's aesthetic feminist activism

    Directory of Open Access Journals (Sweden)

    Rui Pedro Fonseca

    2010-12-01

    Full Text Available Uma das condições para que na sociedade sejam alicerçados valores de género misóginos consiste na existência de uma estrutura de produção cultural heterossexual compulsiva, dominante e universalista que estabeleça princípios de representação dos sexos claramente diferenciados, que tendam a favorecer mais o homem em detrimento da mulher. Partimos de um princípio de que a produção da cultura origina processos de reprodução, o que significa, em termos práticos, que a representação de signos, códigos, valores e comportamentos associados aos sexos é potencialmente materializada nas sociedades, por homens e por mulheres. Essa tem sido uma batalha levada a cabo por muitas mulheres a partir da segunda vaga do movimento feminista, nomeadamente pela ala mais radical, que tem procurado reivindicar novos paradigmas no que diz respeito às convenções culturais de género. O que propomos neste estudo é analisar algumas das campanhas levadas a cabo por Nikki Craft, uma feminista radical norte-americana que viria a organizar e/ou a protagonizar nos anos 1970 e 1980 vários protestos em espaços públicos de algumas cidades dos Estados Unidos. Neste estudo procuramos clarificar as motivações e as estratégias levadas a cabo por essa feminista, cujos activismos incidiram contra algumas das estruturas culturais (campo da arte, instituições da beleza e indústria pornográfica legitimadoras de representações desencadeadoras de prejuízos para a mulherOne of the conditions for misogynic genders to be settled in society consists on the existence of a compulsive dominant and universal heterosexual cultural production, which establishes clearly differentiated representation principles of both sexes. These representation principles tend to favour more the man, disregarding the woman. We consider that culture production gives origin to reproduction processes, which means that, in practical terms, the representation of signs, codes, values

  8. Evidence of Validity of the Job Crafting Behaviors Scale

    Directory of Open Access Journals (Sweden)

    Renata Silva de Carvalho Chinelato

    2015-12-01

    Full Text Available AbstractJob crafting behavior refers to the changes made by workers in their job context for adjusting their activities to their preferences. We sought to adapt and collect validity evidences of the Job Crafting Behaviors Scale for the Brazilian context, in a sample of 491 workers, with a mean age of 26.7 years. Factor analysis revealed that the final instrument consisted of three dimensions (increasing structural job resources, increasing social job resources, increasing challenging job demands, which showed good internal consistency indexes. These dimensions showed low or moderate correlations with work engagement, positive psychological capital, positive job affect, and in-role performance. The scale showed evidence of validity, the use of which is recommended for future research on the changes that people make in their jobs.

  9. Creativity, Community, & Growth: A Social Geography of Urban Craft Beer

    Directory of Open Access Journals (Sweden)

    Neil Reid

    2017-03-01

    Full Text Available To better understand the non-economic drivers of growth in emerging industries, this paper examines the craft beer industry.  Specifically, the paper will review two examples—the Black Cloister Brewing Company in Toledo, OH and 3rd Turn Brewery, Louisville, KY—to understand how the values of entrepreneurs and local firms that are situated at the nexus of work, place, and creativity promote growth.  Further, the paper will consider the socio-cultural meaning of creativity relative to the craft beer industry and the many ways in which the concept of innovation traditionally used by economic geographers to understand growth can be better understood within the context of creativity in some industries.  In doing so, the paper represents a conceptual shift away from innovation towards creativity, as well as community.

  10. Management of the Immigrant Child as a State Crafting Grammar

    DEFF Research Database (Denmark)

    Padovan-Özdemir, Marta; Moldenhawer, Bolette

    This paper engages with the state-migrant nexus by investigating how the crafting of the Danish welfare state can be studied through administrative classifications of the immigrant and the pedagogical practices managing the immigrant of school age. We propose an elaborated statist perspective...... the immigrant of school age as an educational problem emerges with and are legitimized by ambivalent references to regimes of national membership, universal welfare, workfare and securitization....

  11. Multistage aerospace craft. [perspective drawings of conceptual design

    Science.gov (United States)

    Kelly, D. L. (Inventor)

    1973-01-01

    A conceptual design of a multi-stage aerospace craft is presented. Two perspective views of the vehicle are developed to show the two component configuration with delta wing, four vertical tail surfaces, tricycle landing gear, and two rocket exhaust nozzles at the rear of the fuselage. Engines for propulsion in the atmosphere are mounted on the fuselage in front of the wing root attachment.

  12. Modeling emotions with EEG-data in StateCraft

    OpenAIRE

    Slinde, Anders Njøs

    2012-01-01

    Emotions have been shown to play an important part in human decision making, and emotions in Artificial Intelligence have been shown to affect agent performance and believability. The aim of this thesis is to use EEG-data to model players' emotions. The emotion model was incorporated into the existing Emotion module in the computer game known as StateCraft. Using artificial neural networks as a tool, two different models of the players' emotions were created, a gene...

  13. Tracking Porters: Learning the Craft of Techno-Anthropology.

    Science.gov (United States)

    Bruun, Maja Hojer; Krause-Jensen, Jakob; Saltofte, Margit

    2015-01-01

    Anthropology attempts to gain insight into people's experiential life-worlds through long-term fieldwork. The quality of anthropological knowledge production, however, does not depend solely on the duration of the stay in the field, but also on a particular way of seeing social situations. The anthropological perspective is grounded in socio-cultural theory and forged by a distinct relativist or contextualist epistemological stance. The point is to understand events, concepts and phenomena from the insiders' point of view and to show how this view relates to the particular social and cultural context. In this chapter, we argue that although anthropology has its specific methodology - including a myriad of ethnographic data-gathering tools, techniques, analytical approaches and theories - it must first and foremost be understood as a craft. Anthropology as craft requires a specific 'anthropological sensibility' that differs from the standardized procedures of normal science. To establish our points we use an example of problem-based project work conducted by a group of Techno-Anthropology students at Aalborg University, we focus on key aspects of this craft and how the students began to learn it: For two weeks the students followed the work of a group of porters. Drawing on anthropological concepts and research strategies the students gained crucial insights about the potential effects of using tracking technologies in the hospital.

  14. Environmental Support to Amphibious Craft, Patrol Boats, and Coastal Ships: An Annotated Bibliography

    National Research Council Canada - National Science Library

    Bachmann, Charles M; Fusina, Robert A; Nichols, C. R; McDermid, Jack

    2008-01-01

    This annotated bibliography is a selection of citations to books, articles, documents, and data bases highlighting environmental conditions that impact the safety and performance of amphibious craft...

  15. Ergonomic Analysis of the Work Condition in Aluminum Crafts Industry

    Science.gov (United States)

    Soewardi, H.; Taufiq, A.; Pradipta, T.

    2017-12-01

    Indonesia has plenty of abundant natural wealth. This natural wealth produces natural materials that can be utilized as a craft product. The craft workers generally still work manually and the work is done repeatedly in one cycle so it is very susceptible to musculoskeletal disorders. Musculoskeletal disorders will cause decrease of worker’s effectiveness and efficiency in completing the task. Thus, this fact has some adverse impact for the company. The purpose of this study is to analyze some task in manufacturing a traditional cooking tool (griddle) which encompasses mold of the griddle, refine of the griddle and the finishing touch by using the Occupational Repetitive Action Index (OCRA index) method. This method consists of high frequency movements, large forces, awkward postures, insufficient resting time and other factor such as vibration. Result of this study shows that in the molding operation, the worker has uncertain and medium risk on right hand in manufacturing small and large size of griddle with OCRA index is 2.5 and 5.3 respectively. In the refining operation the worker has light and medium risk on left hand in manufacturing small and large size with OCRA index is 3.6 and 5.8 using grinding machine and 5.8, 5.2, 6.3 and 5.0 using miser tool. In finishing operation, the worker has high risk on right hand in numbering of code griddle and has medium risk on right hand and medium on left hand in labeling with OCRA index is 9, 6.1 and 6.8 While in assembling operation the worker has no risk. Score that it indicates the risk level of the task in such job. Thus the following actions are to improve the work condition ergonomicly in all operation in alumunium craft.

  16. Hand-crafted programming objects and visual perception

    CSIR Research Space (South Africa)

    Smith, Adrew C

    2009-05-01

    Full Text Available stream_source_info Smith1_2009.pdf.txt stream_content_type text/plain stream_size 20071 Content-Encoding UTF-8 stream_name Smith1_2009.pdf.txt Content-Type text/plain; charset=UTF-8 IST-Africa 2009 Conference... Proceedings Paul Cunningham and Miriam Cunningham (Eds) IIMC International Information Management Corporation, 2009 ISBN: 978-1-905824-11-3 Copyright © 2009 The authors www.IST-Africa.org/Conference2009 Page 1 of 7 Hand-Crafted Programming Objects...

  17. Craft vs. industrial: Habits, attitudes and motivations towards beer consumption in Mexico.

    Science.gov (United States)

    Gómez-Corona, Carlos; Escalona-Buendía, Héctor B; García, Mauricio; Chollet, Sylvie; Valentin, Dominique

    2016-01-01

    Food choices tend to be stable over time; they do not change fast, since consumers tend to act like creatures of habits. However, food habits can evolve, like currently the craft beer category. A change of habits involves a change of perception towards a product. Therefore, what is changing in the perception of beer? Two studies were conducted to address this question. First study was preliminary and aimed at exploring beer consumption habits in Mexico and a better understanding of craft beer representation among beer users. A questionnaire was administrated to 207 consumers in Mexico City during a beer festival. Results showed that respondents could be classified in: industrial beer (41.1%), occasional industrial (24.1%), and craft beer (34.8%) consumers. Craft cluster included mostly 25-35 years old men with high-income level. Among the craft beers cited by respondents from this cluster some are industrial, suggesting that the concept of craft beer might not be well defined, or defined in ideological terms. The second and main study was conducted using consumer ethnographies to understand the motivations and benefits of craft beer consumption. Opposite to industrial, craft beer emerges as an experience-based and symbolic product rather than a utilitarian one. The main motivation for drinking craft beer seems to be the quest of authenticity. Respondents' motivations to drink craft beer are generated by three important factors: desire for more knowledge, new taste experiences, and move away from the mainstream beer consumption. Craft consumers do not drink the product for its functional attributes, they consume it for what it means and as a consequence they build an identity, perceived as more authentic and unique, in comparison to the mainstream industrial beer consumption in Mexico. Copyright © 2015 Elsevier Ltd. All rights reserved.

  18. 46 CFR 199.175 - Survival craft and rescue boat equipment.

    Science.gov (United States)

    2010-10-01

    ... must be capable of being used at each entrance on either side or at the stern of the boat to enable... the bow of the lifeboat, ready for use. On lifeboats to be launched by free-fall launching, both painters must be stowed near the bow ready for use. (A) If the painter is of synthetic material, the...

  19. 46 CFR 108.540 - Survival craft muster and embarkation arrangements.

    Science.gov (United States)

    2010-10-01

    ... condition with the unit listed not less than up to 15 degrees either way; or (ii) Each embarkation ladder... intended to be moved to the stowed position with a full complement of persons on board. (g) Each davit... ladder as follows: (1) Each embarkation ladder must be approved under approval series 160.117 or be a...

  20. 46 CFR 199.280 - Survival craft embarkation and launching arrangements.

    Science.gov (United States)

    2010-10-01

    ... APPLIANCES AND ARRANGEMENTS LIFESAVING SYSTEMS FOR CERTAIN INSPECTED VESSELS Additional Requirements for... from Ships, 1973, as amended by the Protocol of 1978 (MARPOL 73/78), in the case of an oil tanker; (2... Bulk, in the case of a chemical tanker; or (3) The International Code for the Construction and...

  1. A Survivability Assessment of the Transformable Craft in an Operational Environment

    Science.gov (United States)

    2010-06-01

    THIS PAGE INTENTIONALLY LEFT BLANK xxi EXECUTIVE SUMMARY Seabasing is the future of joint operations abroad. However, without...spreading to neighboring Ecuador , Peru, and Venezuela. With their considerable arsenal and forces, the objective of the San José Cartel and the CFLC is to

  2. Ripples on water. Research-based art and crafts teaching

    Directory of Open Access Journals (Sweden)

    Torunn Paulsen Dagsland

    2015-10-01

    Full Text Available The article focuses on how classroom research from primary and secondary schools can be implemented in, have influence on, change and provide instruction on the subject Art and Crafts in the College of Education and in practice in primary and secondary schools. This article presents and discusses some selected research findings from a project on the subject of Art and Crafts, where students at the secondary level are in a dialogue with art. The results of the study, which are based on a pupil’s perspective, call for a subject didactic reorientation related to young people’s meeting with art in school, towards content that are more related to youth culture and relational meetings with art that are narrative-oriented, interpretation-orientated, experience-orientated, dialogic and multi-voiced. The article also shows how these research findings have become an important part of the teaching of subject didactics, art history and practical aesthetic work in the College of Education.

  3. Overview of craft brewing specificities and potentially associated microbiota.

    Science.gov (United States)

    Rodhouse, Lindsey; Carbonero, Franck

    2017-09-14

    The brewing process differs slightly in craft breweries as compared to industrial breweries, as there are fewer control points. This affects the microbiota of the final product. Beer contains several antimicrobial properties that protect it from pathogens, such as low pH, low oxygen and high carbon dioxide content, and the addition of hops. However, these hurdles have limited power controlling spoilage organisms. Contamination by these organisms can originate in the raw materials, persist in the environment, and be introduced by using flavoring ingredients later in the process. Spoilage is a prominent issue in brewing, and can cause quality degradation resulting in consumer rejection and product waste. For example, lactic acid bacteria are predominately associated with producing a ropy texture and haze, along with producing diacetyl which gives the beer butter flavor notes. Other microorganisms may not affect flavor or aroma, but can retard fermentation by consuming nutrients needed by fermentation yeast. Quality control in craft breweries today relies on culturing methods to detect specific spoilage organisms. Using media can be beneficial for detecting the most common beer spoilers, such as Lactobacillus and Pediococci. However, these methods are time consuming with long incubation periods. Molecular methods such as community profiling or high throughput sequencing are better used for identifying entire populations of beer. These methods allow for detection, differentiation, and identification of taxa.

  4. CRAFT: Multimodality confocal skin imaging for early cancer diagnosis.

    Science.gov (United States)

    Peng, Tong; Xie, Hao; Ding, Yichen; Wang, Weichao; Li, Zhiming; Jin, Dayong; Tang, Yuanhe; Ren, Qiushi; Xi, Peng

    2012-05-01

    Although histological analysis serves as a gold standard to cancer diagnosis, its application on skin cancer detection is largely prohibited due to its invasive nature. To obtain both the structural and pathological information in situ, a Confocal Reflectance/Auto-Fluorescence Tomography (CRAFT) system was established to examine the skin sites in vivo with both reflectance and autofluorescence modes simultaneously. Nude mice skin with cancerous sites and normal skin sites were imaged and compared with the system. The cellular density and reflective intensity in cancerous sites reflects the structural change of the tissue. With the decay coefficient analysis, the corresponding NAD(P)H decay index for cancerous sites is 1.65-fold that of normal sites, leading to a 97.8% of sensitivity and specificity for early cancer diagnosis. The results are verified by the followed histological analysis. Therefore, CRAFT may provide a novel method for the in vivo, non-invasive diagnosis of early cancer. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  5. Use your eyes - metallographic versus superficial traces of the crafting of Bronze Age ornaments

    DEFF Research Database (Denmark)

    Nørgaard, Heide Wrobel

    of superficial crafting traces for further studies will be put on display. As the destructive sampling of artefacts kept in museum exhibitions is becoming more and more difficult, such a basic knowledge concerning the residues of the crafting processes would allow examining artefacts non-destructively...

  6. The Need for the United States Army to Possess a Landing Craft with Maneuver Capabilities

    Science.gov (United States)

    2015-06-12

    landing craft after the 2004 Indian Ocean tsunami and the 2009 Myanmar cyclone.9 The landing craft enabled the relief effort to bypass partially...in Vietnam and Panama to disaster relieve efforts in Haiti, the Indian Ocean , and within the United States. The Army Concept Framework, informed by...

  7. Job crafting at the team and individual level: Implications for work engagement and performance

    NARCIS (Netherlands)

    Tims, M.; Bakker, A.B.; Derks, D.; Rhenen, van W.

    2013-01-01

    Previous research suggests that employee job crafting is positively related to job performance through employee work engagement. The present study expands this individual-level perspective to the team level by hypothesizing that team job crafting relates positively to team performance through team

  8. Computer Technology-Integrated Projects Should Not Supplant Craft Projects in Science Education

    Science.gov (United States)

    Klopp, Tabatha J.; Rule, Audrey C.; Schneider, Jean Suchsland; Boody, Robert M.

    2014-01-01

    The current emphasis on computer technology integration and narrowing of the curriculum has displaced arts and crafts. However, the hands-on, concrete nature of craft work in science modeling enables students to understand difficult concepts and to be engaged and motivated while learning spatial, logical, and sequential thinking skills. Analogy…

  9. The Development of Indian and Eskimo Art and Crafts in the Far North.

    Science.gov (United States)

    Phillips, R. A. J.; And Others

    The focus of the conference, "The Development of Indian and Eskimo Art and Crafts in the Far North," was the creation of a market for reputable Indian and Eskimo art work on an economically sound basis which would benefit both the native artists and the Canadian economy. Two governmental reports, "Northern Arts and Crafts" and…

  10. Mycotoxin profiling of 1000 beer samples with a special focus on craft beer

    NARCIS (Netherlands)

    Peters, Jeroen; Dam, van Ruud; Doorn, van Ronald; Katerere, David; Berthiller, Franz; Haasnoot, Willem; Nielen, Michel W.F.

    2017-01-01

    Currently beer is booming, mainly due to the steady rise of craft breweries worldwide. Previous surveys for occurrence of mycotoxins in beer, were mainly focussed on industrial produced beer. The present survey reports the presence of mycotoxins in craft beer and how this compares to industrial

  11. The geography of informal arts and crafts traders in South Africa's ...

    African Journals Online (AJOL)

    The results show that informal selling of arts and crafts is a relatively small component of street trading in all four centres. Intra-city variations are reported and the geographical patterns of arts and crafts traders in the four centres analysed with GIS software. The purpose of this analysis is to identify concentrations of traders ...

  12. The Intelligence of the Hands: Studying the Origin of Pedagogical Craft Education

    Science.gov (United States)

    Olafsson, Brynjar; Thorsteinsson, Gisli

    2012-01-01

    Pedagogical craft was established in the Scandinavia around 1950 under the name Sloyd. The ideology was developed by European educators from 16th and 17th century. Sloyd aimed to educate children holistically via a carefully structured system for teaching craft. The child became the centre of the educational activities and the development of the…

  13. Job crafting and its impact on work engagement and job satisfaction in mining and manufacturing

    NARCIS (Netherlands)

    De Beer, L.T. (Leon T.); M. Tims (Maria); A.B. Bakker (Arnold)

    2016-01-01

    textabstractThe purpose of this study was to investigate job crafting and its relationship with work engagement and job satisfaction within the South African context. This research is important as job crafting has been shown to have a positive influence on employee motivation. A cross-sectional

  14. Digitizing Craft: Creative Writing Studies and New Media--A Proposal

    Science.gov (United States)

    Koehler, Adam

    2013-01-01

    This article identifies and examines a digital arm of creative writing studies and organizes that proposal into four categories through which to theorize the "craft" of creative production, each borrowed from Tim Mayers's "(Re)Writing Craft: Composition, Creative Writing, and the Future of English Studies": process, genre, author, and…

  15. The influence of the arts-and-crafts movement on the professional status of occupational therapy.

    Science.gov (United States)

    Levine, R E

    1987-04-01

    This paper explores why occupational therapists use arts and crafts as therapeutic modalities. Beginning with the turn-of-the-century origins of occupational therapy, the paper traces the similarities and differences in the ideas and beliefs of the founders of occupational therapy and the proponents of the arts-and-crafts movement.

  16. Examining Design and Craft Education in Iceland. Curriculum development and present situation

    Directory of Open Access Journals (Sweden)

    Brynjar Olafsson

    2010-12-01

    Full Text Available This article reports a research project that examined the background, status, understanding of and attitude to Design and Craft education (Hönnun og smíði in Icelandic elementary schools. The main conclusions showed that certain aspects of Design and Craft need to be further defined in order to strengthen its position in the school system. Concepts were not clearly defined and research on Design and Craft education was lacking. The participants’ attitudes to Design and Craft were positive and the subject was popular amongst students. However, results showed a lack of understanding of the differences between basic terms such as Art, Design and Craft. All of the interviewees thought Design and Craft were important subjects for individualized learning and wanted to give them a more prominent role in general education. Design and Craft education in the Icelandic National Curriculum has not been fully realised. The research identified that schools have not allocated extra hours for the subjects, even though local authorities were supportive and flexibility existed in the time schedule. Lack of finances was, furthermore, not a hindrance to increased Design and Craft education.

  17. Becoming Animated When Teaching Physics, Crafts and Drama Together: A Multidisciplinary Course for Student-Teachers

    Science.gov (United States)

    Kallunki, Veera; Karppinen, Seija; Komulainen, Kauko

    2017-01-01

    This article examines a physics course for pre-service primary teachers in which physics, crafts and drama were taught together by connecting the standpoints of crafts and drama. The study was carried out by three university educators from these disciplines during an advanced optional course for student-teachers at the University of Helsinki in…

  18. Effect of menthol coated craft paper on corrosion of copper in HCl ...

    Indian Academy of Sciences (India)

    Home; Journals; Bulletin of Materials Science; Volume 33; Issue 3. Effect of menthol coated craft paper on corrosion of copper in HCl environment. P Premkumar ... Natural menthol was coated on craft paper by impregnation and studied as volatile corrosion inhibitor for copper in hydrochloric acid environment. The effect of ...

  19. 46 CFR 24.15-5 - Canadian pleasure craft temporarily using navigable waters of the United States.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Canadian pleasure craft temporarily using navigable... SECURITY UNINSPECTED VESSELS GENERAL PROVISIONS Equivalents § 24.15-5 Canadian pleasure craft temporarily using navigable waters of the United States. Uninspected Canadian pleasure craft (uninspected vessels...

  20. 77 FR 32985 - Notice of Inventory Completion: U.S. Department of the Interior, Indian Arts and Crafts Board...

    Science.gov (United States)

    2012-06-04

    ...: Notice. SUMMARY: The Museum of the Plains Indian, Indian Arts and Crafts Board, has completed an... contact the Museum of the Plains Indian, Indian Arts and Crafts Board. Disposition of the human remains to... contact the Museum of the Plains Indian, Indian Arts and Crafts Board at the address below by July 5, 2012...

  1. 25 CFR 309.24 - How will statements about Indian origin of art or craft products be interpreted?

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 2 2010-04-01 2010-04-01 false How will statements about Indian origin of art or craft products be interpreted? 309.24 Section 309.24 Indians INDIAN ARTS AND CRAFTS BOARD, DEPARTMENT OF THE INTERIOR PROTECTION OF INDIAN ARTS AND CRAFTS PRODUCTS § 309.24 How will statements about Indian origin of...

  2. Design- and Craft thinking analysed as Embodied Cognition

    Directory of Open Access Journals (Sweden)

    Camilla Groth

    2016-06-01

    Full Text Available Through the concept of design thinking the act of designing is presented as an intellectual activity, and the act of planning the design is elevated over the making process. However, the importance of materiality and the embodied sense-making that occurs in this context should not be forgotten. In this study, embodied cognition in design and craft practices was investigated through three case studies. The study takes on an enhanced tactile perspective as a methodological platform; thus, the cases involve 1 deafblind makers in ceramics, 2 a practice-led self-study report on tactile experiences while working with clay and 3 a study on design students’ use of their tactile sense during material exploration. The results show that the act of thinking design involves the body as a knowledge provider.

  3. Multipurpose stabilization of the advanced marine surface crafts

    Directory of Open Access Journals (Sweden)

    Sevostyanov Ruslan A.

    2016-01-01

    Full Text Available Advanced marine surface crafts, such as SWATHs, catamarans or hovercrafts become more and more popular for a great range of various tasks. They usually operate at much higher speed than conventional ships. Moreover, in the open sea there are a lot of requirements and restrictions concerning the quality of such crafts’ dynamics, especially in case of the wind or waves. This paper considers application of the control law with a special multipurpose structure for autopilot design for amphibious air cushion vehicles. Such control law allows to decompose the autopilot task into simpler optimization subtasks. Efficiency of this approach is shown in the task of stabilizing yaw angle of the air cushion vehicle in the different weather conditions.

  4. Cooled variable nozzle radial turbine for rotor craft applications

    Science.gov (United States)

    Rogo, C.

    1981-01-01

    An advanced, small 2.27 kb/sec (5 lbs/sec), high temperature, variable area radial turbine was studied for a rotor craft application. Variable capacity cycles including single-shaft and free-turbine engine configurations were analyzed to define an optimum engine design configuration. Parametric optimizations were made on cooled and uncooled rotor configurations. A detailed structural and heat transfer analysis was conducted to provide a 4000-hour life HP turbine with material properties of the 1988 time frame. A pivoted vane and a moveable sidewall geometry were analyzed. Cooling and variable geometry penalties were included in the cycle analysis. A variable geometry free-turbine engine configuration with a design 1477K (2200 F) inlet temperature and a compressor pressure ratio of 16:1 was selected. An uncooled HP radial turbine rotor with a moveable sidewall nozzle showed the highest performance potential for a time weighted duty cycle.

  5. Crafting Sustainable Development Solutions: Frugal Innovations of Grassroots Entrepreneurs

    Directory of Open Access Journals (Sweden)

    Mario Pansera

    2016-01-01

    Full Text Available A shift in the entrepreneurial landscape is taking place brought about by grassroots innovators with little formal education and technological knowhow, living and working in penurious environments. This research represents an emerging third wave of literature on Bottom of the Pyramid innovation, where products are offered for and by the underserved. Using primary and secondary data derived from four cases of grassroots entrepreneurs in the Indian Subcontinent, the study explores the phenomenon where resource scarce entrepreneurs craft solutions that are environmental friendly, with low overall ownership costs, and use locally available material. We argue that the grassroots phenomenon can be fruitfully exploited to achieve the new Sustainable Development Goals proposed by the UN as a post-2015 strategy for the future of global governance. These innovations might have a tremendous impact not only in terms of serving unmet and ignored consumer needs, but also longer term impacts through enhanced productivity, sustainability, poverty reduction and inclusion promotion.

  6. Low-cost silicon wafer dicing using a craft cutter

    KAUST Repository

    Fan, Yiqiang

    2014-05-20

    This paper reports a low-cost silicon wafer dicing technique using a commercial craft cutter. The 4-inch silicon wafers were scribed using a crafter cutter with a mounted diamond blade. The pre-programmed automated process can reach a minimum die feature of 3 mm by 3 mm. We performed this scribing process on the top polished surface of a silicon wafer; we also created a scribing method for the back-unpolished surface in order to protect the structures on the wafer during scribing. Compared with other wafer dicing methods, our proposed dicing technique is extremely low cost (lower than $1,000), and suitable for silicon wafer dicing in microelectromechanical or microfluidic fields, which usually have a relatively large die dimension. The proposed dicing technique is also usable for dicing multiple project wafers, a process where dies of different dimensions are diced on the same wafer.

  7. Neolithic Layer of the Kalmius Settlement in Mariupol. Stone Crafts

    Directory of Open Access Journals (Sweden)

    Kolesnik Aleksandr V.

    2016-06-01

    Full Text Available The multilayer archaeological site Kalmius is situated on the right bank of the Kalmius river in historical center of Mariupol. The excavated area (2,8 m in depth contains cultural layers of the 20th-19th, 18th centuries, Early Middle Age, Late Bronze Age and Neolithic Age. The site was excavated in 2010-2012, 2014. The Neolithic layer includes numerous flint, stone, pottery artifacts, fragments of animal bones. The collection of stone crafts from 2014 excavation is under discussion in the article. It includes about 1200 flint crafts, unique pieces of slabe and sandstone. The flint industry was based on knapping of prismatic cores. The flint blades of middle size (100-120 mm are a framework of the industry. At the finish stage of exploitation the prismatic cores were modified as cuboid-sharped cores. Geometric microliths of various types, side-scrapers, “non-geometric microliths” and blade implements form the structures of tools assemblages. Burins and end-scrapers are absent. Abundant sources of a flint raw material are situated at the distance of about 120 km in the Southern Donbass (Krynka river basin. Flint raw materials are knapped completely. Non-utilized flint flakes more than 40 mm in size are rare. Intensive usage was provoked by a microlitism of a stone inventory. There are an “iron” and two sandstone plates among pieces of “soft” stone. Analogous complexes are famous in the basin of Lower Don region. The flint collection is similar to the flint complexes of the Mariupol burial place too.

  8. An Overview of the Utilisation of Brewery By-Products as Generated by British Craft Breweries

    Directory of Open Access Journals (Sweden)

    Clare Kerby

    2017-06-01

    Full Text Available There is a wide range of information available on by-product disposal methods used by large national breweries. However, little information is available on the methods of by-product disposal used by craft breweries. An investigation was carried out in which 200+ British craft brewers were contacted, of which 90 craft brewers provided basic information about their brewery operations and by-product disposal. Representatives of eleven breweries were interviewed to provide an in-depth case study of their by-product disposal methods. The research found that urban craft brewers use a wider range of disposal methods compared to rural craft brewers; urban brewers dispose of more waste through sewage and landfill, as well as using external companies, such as bio-recycling and anaerobic digester plants, whereas rural brewers have relationships with farmers who dispose of the by-products in various ways. Craft brewers tend to have a direct relationship with the by-product users. Even though they do not have all disposal options available to them which the large industrial breweries have, due to their small scale of by-product production, craft brewers appear to find alternative means of sustainability.

  9. High Job Demands, Still Engaged and Not Burned Out? The Role of Job Crafting.

    Science.gov (United States)

    Hakanen, Jari J; Seppälä, Piia; Peeters, Maria C W

    2017-08-01

    Traditionally, employee well-being has been considered as resulting from decent working conditions arranged by the organization. Much less is known about whether employees themselves can make self-initiated changes to their work, i.e., craft their jobs, in order to stay well, even in highly demanding work situations. The aim of this study was to use the job demands-resources (JD-R model) to investigate whether job crafting buffers the negative impacts of four types of job demands (workload, emotional dissonance, work contents, and physical demands) on burnout and work engagement. A questionnaire study was designed to examine the buffering role of job crafting among 470 Finnish dentists. All in all, 11 out of 16 possible interaction effects of job demands and job crafting on employee well-being were significant. Job crafting particularly buffered the negative effects of job demands on burnout (7/8 significant interactions) and to a somewhat lesser extent also on work engagement (4/8 significant interactions). Applying job crafting techniques appeared to be particularly effective in mitigating the negative effects of quantitative workload (4/4 significant interactions). By demonstrating that job crafting can also buffer the negative impacts of high job demands on employee well-being, this study contributed to the JD-R model as it suggests that job crafting may even be possible under high work demands, and not only in resourceful jobs, as most previous studies have indicated. In addition to the top-down initiatives for improving employee well-being, bottom-up approaches such as job crafting may also be efficient in preventing burnout and enhancing work engagement.

  10. The effects of job crafting on subjective well-being amongst South African high school teachers

    Directory of Open Access Journals (Sweden)

    Sergio Peral

    2016-04-01

    Full Text Available Orientation: Job crafting can result in a number of positive outcomes for teachers, such as increased meaningfulness and engagement at work. Increased work engagement and psychological meaningfulness may yield positive benefits for the practice of teaching, thus highlighting the pivotal role of job crafting.Research purpose: The study’s aim was to investigate the relationship between job crafting and subjective well-being amongst South African high school teachers. Subjective well-being comprises psychological meaningfulness and work engagement. The potential mediating effect that psychological meaningfulness had on this relationship was further explored.Motivation for the study: Being in a highly stressful occupation, teachers need to continuously find ways to craft their working practices in order to deal effectively with their job demands and to capitalise on their available job resources. Furthermore, South Africa’s current education system calls for serious proactive measures to be taken to improve and rectify the current status, such as job crafting.Research approach, design and method: A quantitative, cross-sectional survey design was used and administered to a sample of South African high school teachers situated in Gauteng, South Africa (N = 251.Main findings: A positive relationship was found between job crafting (increasing structural resources and challenging job demands and work engagement. Furthermore, psychological meaningfulness mediated the relationship between job crafting and work engagement amongst the sampled high school teachers.Practical/managerial implications: Teachers who craft their work to better suit their preferences and needs will obtain greater meaning in their work and experience increased levels of work engagement. Training programmes and/or group-based interventions targeted around job crafting techniques may be particularly useful in the South African teaching context.Contribution/value-add: This study

  11. 25 CFR 309.9 - When can non-Indians make and sell products in the style of Indian arts and crafts?

    Science.gov (United States)

    2010-04-01

    ... of Indian arts and crafts? 309.9 Section 309.9 Indians INDIAN ARTS AND CRAFTS BOARD, DEPARTMENT OF THE INTERIOR PROTECTION OF INDIAN ARTS AND CRAFTS PRODUCTS § 309.9 When can non-Indians make and sell products in the style of Indian arts and crafts? A non-Indian can make and sell products in the style of...

  12. 25 CFR 309.1 - How do the regulations in this part carry out the Indian Arts and Crafts Act of 1990?

    Science.gov (United States)

    2010-04-01

    ... Arts and Crafts Act of 1990? 309.1 Section 309.1 Indians INDIAN ARTS AND CRAFTS BOARD, DEPARTMENT OF THE INTERIOR PROTECTION OF INDIAN ARTS AND CRAFTS PRODUCTS § 309.1 How do the regulations in this part carry out the Indian Arts and Crafts Act of 1990? These regulations define the nature and Indian origin...

  13. Workplace Well-Being: The Role of Job Crafting and Autonomy Support

    National Research Council Canada - National Science Library

    Slemp, Gavin R; Kern, Margaret L; Vella-Brodrick, Dianne A

    2015-01-01

    .... The hypothesized model fit the data well; however, a competing model in which autonomy support and job crafting were separate, but correlated direct predictors of well-being provided a better fit to the data...

  14. Ocean disposal of dredged materials from Atlantic Canadian harbours ll. small craft harbours, Gulf Region

    National Research Council Canada - National Science Library

    1984-01-01

    The objective of this report is to provide a compilation of all data related to dredging/ocean disposal of dredged materials from harbours maintained by the Small Craft Harbours Branch of Fisheries...

  15. HOW DO SERVANT LEADERS PROMOTE ENGAGEMENT? A BOTTOM-UP PERSPECTIVE OF JOB CRAFTING

    National Research Council Canada - National Science Library

    Yang, Rui; Ma, Jianhong; Ming, Ying; Huo, Rongmian

    2017-01-01

    We drew on the literature addressing servant leadership and job crafting, self-determination theory, and the job demands-resources model, and hypothesized that employees who are supported by servant...

  16. Microwave-assisted facile and rapid Friedel-Crafts benzoylation of arenes catalysed by bismuth trifluoromethanesulfonate

    DEFF Research Database (Denmark)

    Tran, Phoung Hoang; Hansen, Poul Erik; Pham, Thuy Than

    2014-01-01

    The catalytic activity of metal triflates was investigated in Friedel–Crafts benzoylation under microwave irradiation. Friedel–Crafts benzoylation with benzoyl chloride of a variety of arenes containing electron-rich and electron-poor rings using bismuth triflate under microwave irradiation...... is described. This method allows the preparation of aryl ketones under solventless conditions in good to excellent yields and short reaction time. Bismuth triflate was easily recovered and reused five times without significant loss of the catalytic activity....

  17. Investigations of Thickness Requirement in DNV Rules for High-Speed Craft

    DEFF Research Database (Denmark)

    Pedersen, Preben Terndrup; Zhang, Shengming

    1997-01-01

    Simple formulas for determining impact strength of high-speed craft collisions with floating objects are given in this note. Thereby the minimum mass of a floating object that just ruptures the shell plating is predicted. The minimum thickness requirements of DNV rules for aluminiumcrafts and GRP...... single skin crafts can be converted to critical impact energy and minimum object mass. Some comparisons show an acceptable agreement between present method and DNV test results....

  18. Developing a Diagnostic Test of Verbs for Hands-on Craft Workshops

    OpenAIRE

    Hammond, Mark

    2017-01-01

    The paper describes and evaluates the development of The Verbs for Craft Test, a small-scale diagnostic instrument to measure knowledge of 50 common imperative verbs found in spoken discourse related to technical instruction requiring the use of one’s hands. Still under development, the test is designed to contribute to a pedagogic approach towards relevant English language learning materials to help train professionals of the Japanese craft industry, especially in the context ...

  19. Craft Arts and Tourism in Ceramic Art Village of Kasongan in Yogyakarta

    OpenAIRE

    sp gustami; laksmi kusuma wardani; agus heru setiawan

    2014-01-01

    Yogyakarta is one of Indonesia’s major tourist destinations. This is due to its nature, interesting, unique and fantastic ancient cultural and art sites. Creative industries and the ceramic crafts play an important role in the development of tourism in Yogyakarta. In this paper, ethnographic approach is used to describe the creative process and the ceramic crafts industry in the village of Kasongan, Yogyakarta. Based on the results of the field research, the authors conclude that the ceramic ...

  20. Effective Multicultural Learning in Iterative Cycles; Language Learning Breaking Gender Barriers in Doing Craft

    Directory of Open Access Journals (Sweden)

    Eeva-Maija Henrita Lappalainen

    2014-04-01

    Full Text Available Normal 0 21 MicrosoftInternetExplorer4 Myths prevail on craft, culture and language, and in multicultural learning environments. In multicultural education teaching, I explored the learning language in craft learning environments and in learning situation the myths’ effects on gender gap. Basic terms and conceptions are 1. The Ha-La-Cu - method and learning style: language and textile material and color impression (craft learning in doing, 2. Reflecting the process, generating interpretations of textile material and color impression (design, producing and processing analysis in textile material and color impression learning and 3. Multi-scientific and multicultural education, interactive language and craft learning in doing -pedagogy: in craft activity, the analyses contain elements that are challenging learners in an active and innovative dialogue with a cultural awareness process. This is a tool for transcending the prevailing gender gap. Gathering the material, I used the (Ashman & Conway, 1989 classroom integration model, a cognitive verbalizing method; the contextualized notes I made by partial parallel and phased coding. Analogies and associations were linked to the vocabulary, increasing it in a sensitive creative manner. This multicultural pedagogy and didactic, in various contexts, is effectively breaking the gender gap. Keywords: crafts learning in doing, content analysis, gender gap, Ha-La-Cu –method, multicultural learning   

  1. Job crafting among health care professionals: The role of work engagement.

    Science.gov (United States)

    Bakker, Arnold B

    2017-10-09

    The aim of this study was to examine the impact of job crafting on the quality of the work environment of health care professionals. Job crafting refers to proactive behavior aimed at optimizing the fit between person and job. Using job demands-resources theory, we hypothesized that job crafting would be positively related to job resources and person-organisation fit, and negatively to hindrance demands. Furthermore, we hypothesized that these relationships would be qualified by work engagement. A total of 5,272 health care professionals from one of 35 different organisations filled out an electronic questionnaire (response is 55%). Regression analyses were used to test hypotheses. Consistent with hypotheses, job crafting in the form of increasing job resources was positively related to opportunities for development, performance feedback and P-O fit; and negatively related to hindrance job demands - particularly when work engagement was high. The combination of job crafting and work engagement is important for the realization of a resourceful work environment and fit between person and organisation. Interventions aimed at fostering job crafting should be tailored to the motivation of health care professionals. © 2017 John Wiley & Sons Ltd.

  2. New Methods for Crafting Locally Decision-Relevant Scenarios

    Science.gov (United States)

    Lempert, R. J.

    2015-12-01

    Scenarios can play an important role in helping decision makers to imagine future worlds, both good and bad, different than the one with which we are familiar and to take concrete steps now to address the risks generated by climate change. At their best, scenarios can effectively represent deep uncertainty; integrate over multiple domains; and enable parties with different expectation and values to expand the range of futures they consider, to see the world from different points of view, and to grapple seriously with the potential implications of surprising or inconvenient futures. These attributes of scenario processes can prove crucial in helping craft effective responses to climate change. But traditional scenario methods can also fail to overcome difficulties related to choosing, communicating, and using scenarios to identify, evaluate, and reach consensus on appropriate policies. Such challenges can limit scenario's impact in broad public discourse. This talk will demonstrate how new decision support approaches can employ new quantitative tools that allow scenarios to emerge from a process of deliberation with analysis among stakeholders, rather than serve as inputs to it, thereby increasing the impacts of scenarios on decision making. This talk will demonstrate these methods in the design of a decision support tool to help residents of low lying coastal cities grapple with the long-term risks of sea level rise. In particular, this talk will show how information from the IPCC SSP's can be combined with local information to provide a rich set of locally decision-relevant information.

  3. Electrical Safety Program: Nonelectrical Crafts at LANL, Live #12175

    Energy Technology Data Exchange (ETDEWEB)

    Glass, George [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-12-22

    Los Alamos National Laboratory (LANL) and the federal government require those working with or near electrical equipment to be trained on electrical hazards and how to avoid them. Although you might not be trained to work on electrical systems, your understanding of electricity, how it can hurt you, and what precautions to take when working near electricity could save you or others from injury or death. This course, Electrical Safety Program: Nonelectrical Crafts at LANL (12175), provides knowledge of basic electrical concepts, such as current, voltage, and resistance, and their relationship to each other. You will learn how to apply these concepts to safe work practices while learning about the dangers of electricity—and associated hazards—that you may encounter on the job. The course also discusses what you can do to prevent electrical accidents and what you should do in the event of an electrical emergency. The LANL Electrical Safety Program is defined by LANL Procedure (P) 101-13. An electrical safety officer (ESO) is well versed in this document and should be consulted regarding electrical questions. Appointed by the responsible line manager (RLM), ESOs can tell you if a piece of equipment or an operation is safe or how to make it safe.

  4. Optimal reconfigurations of two-craft Coulomb formations along manifolds

    Science.gov (United States)

    Jones, Drew R.; Schaub, Hanspeter

    2013-02-01

    Coulomb formations refer to swarms of closely flying spacecraft, in which the net electric charge of each vehicle is controlled. Active charge control is central to this concept and enables a propulsion system with highly desirable characteristics, albeit with limited controllability. Numerous Coulomb formation equilibria have been derived, but to maintain and maneuver these configurations, some inertial thrust is required to supplement the nearly propellant-less charge control. In this work, invariant manifold theory is applied to two-craft Coulomb equilibria, which are admitted in a linearized two-body gravity model. The manifolds associated with these systems are analyzed for the first time, and are then utilized as part of a general procedure for formulating optimal reconfigurations. Specifically, uncontrolled flows along the manifolds are sought which provide near continuous transfers from one equilibrium to another. Control is then introduced to match continuity, while minimizing inertial thrusting. This methodology aims to exploit uncontrolled motions and charge control to realize the shape-changing ability of these formations, without large inertial control efforts. Some variations in formulating and parameterizing the optimal transfers are discussed, and analytical expressions are derived to aid in establishing control parameter limits, under certain assumptions. Numerical results are provided, as demonstrative examples of the optimization procedure, using relatively simple control approximations. Finally, Particle Swarm Optimization, a novel stochastic method, is used with considerable success to solve the numerically difficult parameter optimization problems.

  5. Crafting a science life: Learning from twentieth century women

    Science.gov (United States)

    Lenz, Michele Ann

    This study examined how women in the field of science craft a science life. Within a historical and cultural framework, the study analyzed the autobiographies, biographies, and other written works of five noted women scientists who lived during the time period of 1878 through 1992. The women scientists chosen for the study were Lise Meitner, Florence Seibert, Barbara McClintock, Rita Levi-Montalcini, and Rosalind Franklin. Together they represented the three major science disciplines of biology, chemistry and physics. I attempted to make sense of my own science life using the stories of the women scientists as a framework. Situating my experiences within the context of the lives of the women scientists allowed me to use a phenomenological approach to discern commonalities within their lives and my own. The results indicated that the women scientists and myself encountered multiple obstacles in terms of access and equity. However, it was also indicated that all of the women in the study developed a variety of techniques, including resistance and accommodation, in order to navigate these obstacles while still being able to pursue their chosen career path. These women did, however, make great sacrifices that cost them personally, emotionally, financially, and even in terms of their career advancement. Their success was closely tied to their ability to forge their own path, to create their own way of living, and to accept themselves as nonconformists.

  6. Greener Friedel-Crafts Acylation using Microwave-enhanced reactivity of Bismuth Triflate in the Friedel-Crafts Benzoylation of Aromatic Compounds with Benzoic Anhydride

    DEFF Research Database (Denmark)

    Tran, Phuong Hoang; Nguyen, Hai Truong; Hansen, Poul Erik

    2017-01-01

    An efficient and facile bismuth trifluoromethanesulfonate-catalyzed benzoylation of aromatic compounds using benzoic anhydride under solvent-free microwave irradiation has been developed. The microwave-assisted Friedel-Crafts benzoylation results in good yields within short reaction times. Bismuth...

  7. Different Types of Employee Well-Being Across Time and Their Relationships With Job Crafting.

    Science.gov (United States)

    Hakanen, Jari J; Peeters, Maria C W; Schaufeli, Wilmar B

    2017-02-13

    We used and integrated the circumplex model of affect (Russell, 1980) and the conservation of resources theory (Hobfoll, 1998) to hypothesize how various types of employee well-being, which can be differentiated on theoretical grounds (i.e., work engagement, job satisfaction, burnout, and workaholism), may differently predict various job crafting behaviors (i.e., increasing structural and social resources and challenging demands, and decreasing hindering demands) and each other over time. At Time 1, we measured employee well-being, and 4 years later at Time 2, job crafting and well-being, using a large sample of Finnish dentists (N = 1,877). The results of structural equation modeling showed that (a) work engagement positively predicted both types of increasing resources and challenging demands and negatively predicted decreasing hindering demands; (b) workaholism positively predicted increasing structural resources and challenging demands; (c) burnout positively predicted decreasing hindering demands and negatively predicted increasing structural resources, whereas (d) job satisfaction did not relate to job crafting over time; and (e) work engagement positively influenced job satisfaction and negatively influenced burnout, whereas (f) workaholism predicted burnout after controlling for baseline levels. Thus, work engagement was a stronger predictor of future job crafting and other types of employee well-being than job satisfaction. Although workaholism was positively associated with job crafting, it also predicted burnout. We conclude that the relationship between job crafting and employee well-being may be more complex than assumed, because the way in which employees will craft their jobs in the future seems to depend on how they currently feel. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

  8. Leader–member exchange fosters work engagement: The mediating role of job crafting

    Directory of Open Access Journals (Sweden)

    Mirjam Radstaak

    2017-01-01

    Full Text Available Orientation: The right balance between job demands and job resources are essential for employees to bring energy and enthusiasm to work. Employees who experience high-quality relationships with their supervisors may actively craft their job demands and job resources and feel more engaged.Research purpose: The current study examined the associations between leader–member exchange (LMX, job crafting and work engagement. Motivation: This study attempts to gain more insight in the associations between LMX, job crafting and work engagement. It was hypothesised that high-quality relationships with supervisors fosters work engagement because it stimulates employees to craft their jobs by increasing social and structural job resources and challenging job demands and by decreasing hindering job demands.Research approach, design and methodology: Participants (N = 402 working for a leading mail and parcels company in the Netherlands completed questionnaires measuring LMX, work engagement and job crafting. Structural equation modelling was used to examine the hypotheses.Main findings: Increasing social job resources (β = 0.01, SE = 0.00, p < 0.001 and increasing challenging job demands (β = 0.08, SE = 0.04, p < 0.05 were significant mediators in the association between LMX and work engagement. Increasing structural job resources (β = 0.00, SE = 0.00, p = 0.92 and decreasing hindering job demands (β = -0.00, SE 0.00, p = 0.09 were not significant mediators.Practical and managerial implications: Supervisors who are capable of building high-quality relationships with their employees based on trust, respect and loyalty will foster a positive, fulfilling work-related state of mind among employees because they are more willing to proactively craft a challenging and resourceful work environment.Contribution or value-add: The findings of this study showed the importance of high-quality relationships with supervisors and were unique in examining the

  9. Crafting an International Study of Students' Conceptual Understanding of Astronomy

    Science.gov (United States)

    Slater, Stephanie; Bretones, P. S.; McKinnon, D.; Schleigh, S.; Slater, T. F.; Astronomy, Center; Education Research, Physics

    2013-01-01

    Large international investigations into the learning of science, such as the TIMSS and PISA studies, have been enlightening with regard to effective instructional practices. Data from these studies revealed weaknesses and promising practices within nations' educational systems, with evidence to suggest that these studies have led to international reforms in science education. However, these reforms have focused on the general characteristics of teaching and learning across all sciences. While extraordinarily useful, these studies have provided limited insight for any given content domain. To date, there has been no systematic effort to measure individual's conceptual astronomy understanding across the globe. This paper describes our motivations for a coordinated, multinational study of astronomy understanding. First, reformed education is based upon knowing the preexisting knowledge state of our students. The data from this study will be used to assist international astronomy education and public outreach (EPO) professionals in their efforts to improve practices across global settings. Second, while the US astronomy EPO community has a long history of activity, research has established that many practices are ineffective in the face of robust misconceptions (e.g.: seasons). Within an international sample we hope to find subpopulations that do not conform to our existing knowledge of student misconceptions, leading us to cultural or educational practices that hint at alternative, effective means of instruction. Finally, it is our hope that this first venture into large-scale disciplinary collaboration will help us to craft a set of common languages and practices, building capacity and leading toward long-term cooperation across the international EPO community. This project is sponsored and managed by the Center for Astronomy & Physics Education Research (CAPER), in collaboration with members of the International Astronomical Union-Commission 46. We are actively

  10. Science and art of synthesis and crafting of nano/microstructures and devices using ion-crafted templates: a review

    Science.gov (United States)

    Chakarvarti, S. K.

    2006-03-01

    The miniaturization of devices and synthesis of new materials have a tremendous role in the development of powerful electronics as well as material based technologies in other areas but for the laws of quantum mechanics posing limitations besides the increasing cost and difficulties in manufacturing at such a small scale. The quest, therefore, for the alternative technologies have stimulated a surge of interest in nano-meter scale materials and devices in the recent years. Metallic nano wires are the most attractive materials because of their unique properties having myriad applications like interconnects for nano-electronics, magnetic devices, chemical and biosensors, where as the hollow tubules are equally considered to be candidate for more potent applications- both in physical as well as biosciences. Materials' processing for nano-structured devices is indispensable to their rational design. The technique, known as "Template Synthesis", using electrochemical/electro less deposition is one of the most important processes for manufacturing nano/micro structures, nano-composites and devices and is relatively inexpensive and simple. The technique involves in using membranes- ion crafted ones (popularly known as Particle Track-Etch Membranes or Nuclear Track Filters), alumite substrate membranes, besides other types of membranes as templates. The parameters viz., diameter as well as length i.e., the aspect ratio, shape and wall surface traits in these membranes are controllable. In the present work, a detailed review of this technique, synthesis of nano/micro materials including hybrid materials and devices like field-ion emitters, resonant tunneling diodes (RTDs) etc. will be presented including most of the results obtained in our laboratory.

  11. Job crafting and its impact on work engagement and job satisfaction in mining and manufacturing

    Directory of Open Access Journals (Sweden)

    Leon T de Beer

    2016-09-01

    Full Text Available The purpose of this study was to investigate job crafting and its relationship with work engagement and job satisfaction within the South African context. This research is important as job crafting has been shown to have a positive influence on employee motivation. A cross-sectional survey design was used to collect primary data from organisations in the mining and manufacturing industries of South Africa (N = 470. The results of multi-group structural equation modelling showed that the original four-factor structure of the job crafting scale was supported by the data, but that a three-factor structure was necessary due to a discriminant validity concern regarding two job crafting dimensions. Regression results revealed that increasing structural job resources with challenging job demands, and increasing social job resources were significant predictors of work engagement in both groups. Contrary to expectations decreasing hindering job demands was a negative predictor of job satisfaction in the mining group. Furthermore, increasing social job resources was also a significant predictor of job satisfaction in both groups. This study indicates the importance of job crafting for work engagement and job satisfaction in organisations.

  12. Alternative theoretical and methodological approaches for exploring higher education in Art and Crafts

    Directory of Open Access Journals (Sweden)

    Marte Sørebø Gulliksen

    2009-12-01

    Full Text Available This article presents and discusses approaches for exploring higher education in Art and Crafts. The concepts exploring versus research and the different foci in an insider perspective versus an outsider perspective introduces the theme. An insider perspective is said to be a useful starting point for inquiry, referring to Frayling’s trichotomy research into, research on and research through from 1993. The field of higher education in Art and Crafts education is shortly presented as comprising two main areas of knowledge: knowledge of education, and knowledge about the different subject areas within Art and Crafts. Both theory and practice are a part of these areas of knowledge. As higher education in Art and Crafts is a making profession, the most prominent challenge when exploring this today is thus said to be to develop research based knowledge on Education in Art and Crafts as a making discipline.  Two keywords are deemed to be useful in approaching this theme: Mode 2 knowledge production and transdisciplinarity. The article concludes with describing specific ways of doing this today from within the context of application. Two examples of large research projects in Scandinavia are presented as examples of such projects.

  13. Survival Analysis

    CERN Document Server

    Miller, Rupert G

    2011-01-01

    A concise summary of the statistical methods used in the analysis of survival data with censoring. Emphasizes recently developed nonparametric techniques. Outlines methods in detail and illustrates them with actual data. Discusses the theory behind each method. Includes numerous worked problems and numerical exercises.

  14. Modelling survival

    DEFF Research Database (Denmark)

    Ashauer, Roman; Albert, Carlo; Augustine, Starrlight

    2016-01-01

    well GUTS, calibrated with short-term survival data of Gammarus pulex exposed to four pesticides, can forecast effects of longer-term pulsed exposures. Thirdly, we tested the ability of GUTS to estimate 14-day median effect concentrations of malathion for a range of species and use these estimates...

  15. Continual Online Evolutionary Planning for In-Game Build Order Adaptation in StarCraft

    DEFF Research Database (Denmark)

    Justesen, Niels Orsleff; Risi, Sebastian

    2017-01-01

    able to switch between predefined strategies, which makes it hard to adapt to new situations. This paper introduces an evolutionary-based method to overcome this challenge, called Continual Online Evolutionary Planning (COEP), which is able to perform in-game adaptive build-order planning. COEP...... was added to an open source StarCraft bot called UAlbertaBot and is able to outperform the built-in bots in the game as well as being competitive against a number of scripted opening strategies. The COEP augmented bot can change its build order dynamically and quickly adapt to the opponent’s strategy.......The real-time strategy game StarCraft has become an important benchmark for AI research as it poses a complex environment with numerous challenges. An important strategic aspect in this game is to decide what buildings and units to produce. StarCraft bots playing in AI competitions today are only...

  16. The development and validation of a job crafting measure for use with blue-collar workers

    DEFF Research Database (Denmark)

    Nielsen, Karina; Abildgaard, Johan Simonsen

    2012-01-01

    are characterized by poor working conditions and low well-being. We present the development and adaptation of a job crafting measure that may be used among blue-collar workers, based on an existing scale by Tims, Bakker, and Derks (2012) that was not specifically developed for blue-collar workers. We test....... They also add to knowledge of the job crafting behaviours in which blue-collar workers engage and link them to well-being outcomes.......Abstract Job crafting describes a set of proactive behaviours in which employees may engage to shape their work in order to minimize hindering job demands and maximize resources and challenging demands. Such behaviours may be particularly important among blue-collar workers whose jobs...

  17. Poly(vinyl chloride-grafted multi-walled carbon nanotubes via Friedel-Crafts alkylation

    Directory of Open Access Journals (Sweden)

    2010-11-01

    Full Text Available A novel approach was developed for the surface modification of the multi-walled carbon nanotubes (MWCNTs with high percentage of grafting (PG% by the grafting of polymer via the Friedel-Crafts alkylation. The graft reaction conditions, such as the amount of catalyst added, the reaction temperature, and the reaction time were optimized for the Friedel-Crafts alkylation of the MWCNTs with poly(vinyl chloride (PVC with anhydrous aluminum chloride (AlCl3 as catalyst in chloroform (CHCl3. The Fourier Transform Infrared (FT-IR, Raman, and thermogravimetric (TGA analysis showed that PVC had been successfully grafted onto MWCNTs both at the ends and on the sidewalls by the proposed Friedel-Crafts alkylation. The PVC grafted MWCNTs (PVC-MWCNTs could be dispersed well in organic solvent and the dispersion was more stable.

  18. Job crafting, work engagement, and psychological distress among Japanese employees: a cross-sectional study.

    Science.gov (United States)

    Sakuraya, Asuka; Shimazu, Akihito; Eguchi, Hisashi; Kamiyama, Kimika; Hara, Yujiro; Namba, Katsuyuki; Kawakami, Norito

    2017-01-01

    Job crafting, an employee-initiated job design/redesign, has become important for employees' well-being. However, most studies on the relationship between job crafting and employees' well-being have been conducted in western countries; thus, it is unclear whether job crafting can be effectively applied to Asian cultures, such as Japan, which emphasizes group harmony. The aim of this study was to examine the cross-sectional associations of self-reported job crafting with work engagement and psychological distress among employees in Japan. A questionnaire survey through the internet was conducted among all employees of a manufacturing company in Japan. We analyzed the data from 894 respondents, all employees with regular employment. Job crafting, work engagement, and psychological distress were assessed using the Japanese version of the Job Crafting Questionnaire, the Japanese version of the Utrecht Work Engagement Scale (UWES), and the Brief Job Stress Questionnaire (BJSQ), respectively. Hierarchical multiple regression showed that increasing structural job resources, social job resources, and challenging job demands was significantly and positively associated with work engagement (β = 0.31, p < 0.001; β = 0.14, p < 0.001; β = 0.36, p < 0.001, respectively). For psychological distress, increasing structural job resources was significantly and negatively associated with psychological distress (β = -0.15, p < 0.001). Our study suggests that increasing structural job resources is associated with higher work engagement and lower psychological distress. In addition, increasing social job resources and challenging job demands are also associated with higher work engagement.

  19. Modern Friedel-Crafts chemistry: Part 36. Facile synthesis of some new pyrido[3,2,1-jk]carbazoles via Friedel-Crafts cyclialkylations

    Directory of Open Access Journals (Sweden)

    El-Aal Abd Kotb Abdou Hassan

    2013-01-01

    Full Text Available An efficient methodology for the synthesis of novel substituted pyrido[3,2,1-jk]carbazole via Friedel-Crafts cyclialkylations is reported. The methodology was realized by three-step protocol involved the addition of carbazole to 3-methylcrotononitrile. The resulted nitrile was hydrolyzed to desired ester, followed by addition of Grignard reagents to afford tertiary alcohols and/or reacted directly with different Grignard reagent to form the desired ketones. The later ketones were converted to both secondary and tertiary alcohols by reduction with LAH and addition of Grignard reagents respectively. These carbinols were cyclialkylated under Friedel-Crafts conditions catalyzed by AlCl3/CH3NO2, PTSA and PPA to give tri-and tetrasubstituted pyrido[3,2,1-jk]carbazole.

  20. The Simulation of Wave Slam Impulses to Evaluate Shock Mitigation Seats For High-Speed Planing Craft

    Science.gov (United States)

    2013-05-17

    engineering [25].” Planing craft motions include all six degrees of freedom: three translational (i.e., heave, surge , sway ) and three rotational (i.e., pitch...Motion Rigid body motions of a craft are its absolute translations (heave, surge , and sway ) and rotations (pitch, roll, and yaw) in a seaway. It...critical damping coefficient

  1. Innovations’ Survival

    Directory of Open Access Journals (Sweden)

    Jakub Tabas

    2016-01-01

    Full Text Available Innovations currently represent a tool of maintaining the going concern of a business entity and its competitiveness. However, effects of innovations are not infinite and if an innovation should constantly preserve a life of business entity, it has to be a continual chain of innovations, i.e. continual process. Effective live of a single innovation is limited while the limitation is derived especially from industry. The paper provides the results of research on innovations effects in the financial performance of small and medium-sized enterprises in the Czech Republic. Objective of this paper is to determine the length and intensity of the effects of technical innovations in company’s financial performance. The economic effect of innovations has been measured at application of company’s gross production power while the Deviation Analysis has been applied for three years’ time series. Subsequently the Survival Analysis has been applied. The analyses are elaborated for three statistical samples of SMEs constructed in accordance to the industry. The results obtained show significant differences in innovations’ survival within these three samples of enterprises then. The results are quite specific for the industries, and are confronted and discussed with the results of authors’ former research on the issue.

  2. Primary student teachers’ perceptions of their prior experiences with craft-making in light of Hannah Arendt’s human condition

    Directory of Open Access Journals (Sweden)

    Seija Karppinen

    2013-09-01

    Full Text Available This article presents the results of a study about student teachers’ feelings toward craft-making and teaching crafts. As a teacher educator in teacher training, my interest lies first in student teachers’ prior craft experiences and in their prejudices about themselves as craft-makers in relation to the human condition as set forth by philosopher Hannah Arendt (1958/2002. Second, I am interested in how students’ experiences and their image of crafts affect their attitude to crafts and teaching crafts. The study uses qualitative content analysis (e.g. Cohen, Manion & Morrison, 2007, concept clarification (e.g. Kramer, 1993; Burkin, 2011 and thought experiments (Zalta, 2011; Cohnitz, 2006; Sorensen, 1992 to identify and categorise student teachers’ emotional experiences. The data consist of essays (craft biographies, N=144 by first-year student teachers which were written in 2008 and 2009 during a basic course in crafts as part of teacher education at the University of Helsinki. Arendt (1958/2002 labelled the elements of the human condition as labour, work and action. In this study I discuss how, for instance, Arendtian concepts could be explained in relation to crafts, craft-making and education. Arendt categorises craft, defined as things made by hand, as part of the concept of work. In this study, I consider whether crafts and craft-making could be part of other Arendtian terms as well and how these terms fit various educational situations. As a result, there is a need for additional terms alongside Arendtian terms to describe multifaceted craft-making and primary student teachers’ perceptions of themselves as craft-makers. In relation to student teachers’ memories on primary school crafts, I have labelled Arendtian concept labour as students’ credit-orientated activity, the concept of work as making-orientated activity and the concept of action as interaction-orientated activity. These three orientations of craft frame student

  3. Scholarisation, Apprenticeship and Social Differentiation. Analysis of the Non-Industrial Craft Sector in Morocco

    Science.gov (United States)

    Gerard, Etienne

    2012-01-01

    The article approaches the question of the schooling processes in the particular environment of the Moroccan craftsmen of Fez. It shows that the weak schooling of the children is bound to the representations and to the ways of transmission of craft industry knowledge. Schooling is, indeed, the object of tensions between a school system of western…

  4. Job crafting in changing organizations: Antecedents and implications for exhaustion and performance.

    Science.gov (United States)

    Petrou, Paraskevas; Demerouti, Evangelia; Schaufeli, Wilmar B

    2015-10-01

    The present study addressed employee job crafting behaviors (i.e., seeking resources, seeking challenges, and reducing demands) in the context of organizational change. We examined predictors of job crafting both at the organizational level (i.e., perceived impact of the implemented changes on the working life of employees) and the individual level (i.e., employee willingness to follow the changes). Job crafting behaviors were expected to predict task performance and exhaustion. Two-wave longitudinal data from 580 police officers undergoing organizational changes were analyzed with structural equation modeling. Findings showed that the degree to which changes influence employees' daily work was linked to reducing demands and exhaustion, whereas employee willingness to change was linked to seeking resources and seeking challenges. Furthermore, while seeking resources and seeking challenges were associated with high task performance and low exhaustion respectively, reducing demands seemed to predict exhaustion positively. Our findings suggest that job crafting can act as a strategy of employees to respond to organizational change. While seeking resources and seeking challenges enhance employee adjustment and should be encouraged by managers, reducing demands seems to have unfavorable implications for employees. (c) 2015 APA, all rights reserved).

  5. Critical Success Factors in Crafting Strategic Architecture for E-Learning at HP University

    Science.gov (United States)

    Sharma, Kunal; Pandit, Pallvi; Pandit, Parul

    2011-01-01

    Purpose: The purpose of this paper is to outline the critical success factors for crafting a strategic architecture for e-learning at HP University. Design/methodology/approach: A descriptive survey type of research design was used. An empirical study was conducted on students enrolled with the International Centre for Distance and Open Learning…

  6. An Investigation of Wave Impact Duration in High-Speed Planing Craft in Rough Water

    Science.gov (United States)

    2014-04-01

    body modes and the vibration modes. Rigid Body Motions Rigid body motions of a craft are its absolute translations (heave, surge , and sway ) and... Damped Example ............................................................................................19 NSWCCD-80-TR-2014/026 iv Lightly... Damped Example .............................................................................................22 Peak Acceleration versus Pulse Duration

  7. Acceleration Response Mode Decomposition for Quantifying Wave Impact Load in High-Speed Planing Craft

    Science.gov (United States)

    2014-04-01

    ESG value is a convenient parameter that enables investigations of the static strength of materials for structures operating in dynamic...environments. The use of the ESG for investigating craft structural strength could also be extended into a Level II investigations by considering the effects

  8. The African Female Writer and Her Craft: Aspects of Yvonne Vera's ...

    African Journals Online (AJOL)

    This paper is particularly concerned with identifying and examining some peculiar features of Yvonne Vera's literary artistry. It essentially explores the varied ways the Zimbabwean writer has articulated some aspects of her feminist viewpoint through the unique manner she crafts her novels. While drawing illustrations from ...

  9. Urban networks and Arctic outlands: Craft specialists and reindeer antler in Viking towns

    DEFF Research Database (Denmark)

    Ashby, Steven P.; Coutu, Ashley N.; Sindbæk, Søren Michael

    2015-01-01

    This paper presents the results of the use of a minimally destructive biomolecular technique to explore the resource networks behind one of the first specialized urban crafts in early mediaeval northern Europe: the manufacture of composite combs of deer antler. The research incorporates the largest...

  10. Crafting the Set of Buckets in a R&D Portfolio

    DEFF Research Database (Denmark)

    Santiago, Leonardo; Soares, Verônica Mariana Oliveira

    2017-01-01

    The fact that R&D portfolio should be aligned with firm’s strategy is self-evident. The strategic buckets method is often posited in the literature as an alternative to ensure the strategic alignment. However, crafting the right set of buckets is not a straightforward task. In this paper, we...

  11. Dialogue between Art and Craft: Textile Materials and Techniques in Contemporary Art

    Science.gov (United States)

    Pöllänen, Sinikka; Ruotsalainen, Kati

    2017-01-01

    The aim of this study was to investigate the ways in which textile materials and techniques are expressed in contemporary art in Finland. The first phase of data collection was to identify a population of Finnish artists who use textile craft-based forms in their art and who produce their works themselves. After that, six discretionary selected…

  12. An Illuminative Evaluation on Practical Art, Craft and Design Instruction: The Case of Botswana

    Science.gov (United States)

    Mannathoko, Magdeline C.; Major, Thenjiwe E.

    2013-01-01

    Art, craft and design (ACD) is a practical subject that provides learners the opportunity to explore various media and techniques. This includes creating two and three dimensional work in order to help learners develop their practical skills which may benefit them in future. Learners may create products to sell and earn a living as the National…

  13. The use of arts and crafts in the rehabilitation of the adult burn patient.

    Science.gov (United States)

    Sanford, S L; Cash, S H; Nelson, C

    1995-01-01

    The purpose of this study was to gain insight into one small aspect of occupational therapy: the use of arts and crafts in the rehabilitation of the adult burn patient. While burn care literature is plentiful, that related specifically to occupational therapy treatment of burn patients is scarce. A survey was mailed to occupational therapists in 165 burn units across the United States. Responses to survey questions indicate that a majority of respondents (73%%) do not use arts and crafts in the rehabilitation of adult burn patients, while 26%% do use these modalities. Those respondents who do use arts and crafts stated that they use leatherwork, painting, and woodworking most frequently. Therapists who do not use arts and crafts indicated that their primary reasons for not doing so were the acutely ill status of the patients and wound drainage/sterility issues. The entire scope of occupational therapy treatment of burn patients deserves greater attention as it is a challenging and rapidly-evolving area of practice.

  14. 3D DIGITAL SIMULATION OF MINNAN TEMPLE ARCHITECTURE CAISSON'S CRAFT TECHNIQUES

    Directory of Open Access Journals (Sweden)

    Y. C. Lin

    2013-07-01

    Full Text Available Caisson is one of the important representations of the Minnan (southern Fujian temple architecture craft techniques and decorative aesthetics. The special component design and group building method present the architectural thinking and personal characteristics of great carpenters of Minnan temple architecture. In late Qing Dynasty, the appearance and style of caissons of famous temples in Taiwan apparently presented the building techniques of the great carpenters. However, as the years went by, the caisson design and craft techniques were not fully inherited, which has been a great loss of cultural assets. Accordingly, with the caisson of Fulong temple, a work by the well-known great carpenter in Tainan as an example, this study obtained the thinking principles of the original design and the design method at initial period of construction through interview records and the step of redrawing the "Tng-Ko" (traditional design, stakeout and construction tool. We obtained the 3D point cloud model of the caisson of Fulong temple using 3D laser scanning technology, and established the 3D digital model of each component of the caisson. Based on the caisson component procedure obtained from interview records, this study conducted the digital simulation of the caisson component to completely recode and present the caisson design, construction and completion procedure. This model of preserving the craft techniques for Minnan temple caisson by using digital technology makes specific contribution to the heritage of the craft techniques while providing an important reference for the digital preservation of human cultural assets.

  15. High Job Demands, Still Engaged and Not Burned Out? The Role of Job Crafting

    NARCIS (Netherlands)

    Hakanen, Jari J.; Seppälä, Piia; Peeters, Maria C W

    2017-01-01

    Purpose: Traditionally, employee well-being has been considered as resulting from decent working conditions arranged by the organization. Much less is known about whether employees themselves can make self-initiated changes to their work, i.e., craft their jobs, in order to stay well, even in highly

  16. Traditional Craft or Technology Education: Development of Students' Technical Abilities in Finnish Comprehensive School

    Science.gov (United States)

    Autio, Ossi

    2016-01-01

    Changes in the economy, nature, production and society together with increasing scientific and technological knowledge make demands of transforming school teaching in the field of technology education. The aim of the article is briefly to explore the integration between science, technology and traditional craft education by analyzing the current…

  17. the secret south african project: building strike craft, 1975-79

    African Journals Online (AJOL)

    fsc

    computerised database of all spare parts was created in order to effectively manage onboard and shore spare parts stores. To this end the project team had to both order spare parts for the onboard storage as well as order and dispatch sufficient spare parts for the maintenance and service of the strike craft in South Africa.

  18. 76 FR 38153 - California State Nonroad Engine Pollution Control Standards; Commercial Harbor Craft Regulations...

    Science.gov (United States)

    2011-06-29

    ... nitrogen from new and in-use diesel- fueled engines on commercial harbor craft. CARB has requested that EPA... . Fax: (202) 566-1741. Mail: Air and Radiation Docket, Docket ID No. EPA-HQ-OAR- 2011-0549, U.S... proceeding are contained in the Air and Radiation Docket and Information Center, maintained in Docket ID No...

  19. Craft Arts and Tourism in Ceramic Art Village of Kasongan in Yogyakarta

    Directory of Open Access Journals (Sweden)

    sp gustami

    2014-03-01

    Full Text Available Yogyakarta is one of Indonesia’s major tourist destinations. This is due to its nature, interesting, unique and fantastic ancient cultural and art sites. Creative industries and the ceramic crafts play an important role in the development of tourism in Yogyakarta. In this paper, ethnographic approach is used to describe the creative process and the ceramic crafts industry in the village of Kasongan, Yogyakarta. Based on the results of the field research, the authors conclude that the ceramic crafts tourist village of Kasongan is moving toward greater commoditization whereby the ceramics centre is now more oriented towards meeting the needs of tourist industry in Yogyakarta. Due to extensive interaction and the positive response from the general public, ceramic crafts practitioners of Kasongan experience unique and characteristic creative period. The crafters manage to negotiate between the old and the new values, in the village one can find both traditional pottery and new, creative and innovative ceramic products of export quality. Today, Kasongan is a trade mark ceramic tourism village that is entering the global era.

  20. The Craft of Poetry: A Directed-Study Seminar Course Planned by Knowles' Andragogical Principles.

    Science.gov (United States)

    Kelso, Genell

    This paper describes a directed-study seminar course in the craft of poetry using Malcolm Knowles' andragogical principles of teaching (related to the educational process of adults as contrasted with pedagogy, the educational process of children). The background and significance of the course are discussed and procedures for administering it,…

  1. Synthesis of isopropyl-substituted anthraquinones via Friedel–Crafts acylations: migration of isopropyl groups

    Science.gov (United States)

    Chakiri, Abdel B.

    2017-01-01

    Friedel–Crafts reactions of isopropyl-substituted benzenes with phthalic anhydride in the presence of aluminium trichloride, followed by cyclization of the products with strong sulfuric acid give, as expected, anthraquinones. The syntheses, however, often afford more than one anthraquinone. In some cases the isopropyl groups migrate cleanly to other ring positions; in other cases they are lost. PMID:28878991

  2. Effects of spent craft brewers’ yeast on fermentation and methane production by rumen microorganisms

    Science.gov (United States)

    Saccharomyces cerevisiae is a key component of beer brewing and a major by-product. The leftover, spent brewers’ yeast, from large breweries has been used for some time as a protein supplement in cattle, however the possible advantages of spent yeast from smaller craft breweries, containing much hig...

  3. Industrial Crafts. A Bilingual Text = Trabajos Manuales Industriales. Un Texto Bilingue.

    Science.gov (United States)

    Los Angeles Unified School District, CA. Div. of Career and Continuing Education.

    This bilingual instructional text, one in a series of six texts covering various vocational and technical topics, provides secondary level English and Spanish instruction in industrial crafts. Addressed in the individual units are the following topics: plastics; laminating acrylic plastic; thermoforming plastics; sawing, shaping, and finishing…

  4. Good Work and Aesthetic Education: William Morris, the Arts and Crafts Movement, and beyond

    Science.gov (United States)

    Petts, Jeffrey

    2008-01-01

    A notion of "good work," derived from William Morris and the Arts and Crafts Movement but also part of a wider tradition in philosophy (associated with pragmatism and Everyday Aesthetics) understanding the global significance of, and opportunities for, aesthetic experience, grounds both art making and appreciation in the organization of labor…

  5. Fatigue resistance of welded joints in aluminium high-speed craft : A total stress concept

    NARCIS (Netherlands)

    Den Besten, J.H.

    2015-01-01

    Crew transfers, surveillance duties and {security, rescue, interception} operations at sea typically require high-speed craft. Aluminium is quite often selected as hull structure material because of its weight save potential in comparison to steel. The fatigue strength, however, may become a point

  6. Mycotoxin profiling of 1000 beer samples with a special focus on craft beer

    Science.gov (United States)

    van Dam, Ruud; van Doorn, Ronald; Katerere, David; Berthiller, Franz; Haasnoot, Willem; Nielen, Michel W. F.

    2017-01-01

    Currently beer is booming, mainly due to the steady rise of craft breweries worldwide. Previous surveys for occurrence of mycotoxins in beer, were mainly focussed on industrial produced beer. The present survey reports the presence of mycotoxins in craft beer and how this compares to industrial produced beer. More than 1000 beers were collected from 47 countries, of which 60% were craft beers. A selection of 1000 samples were screened for the presence of aflatoxin B1, ochratoxin A (OTA), zearalenone (ZEN), fumonisins (FBs), T-2 and HT-2 toxins (T-2 and HT-2) and deoxynivalenol (DON) using a mycotoxin 6-plex immunoassay. For confirmatory analysis, a liquid chromatography tandem mass spectrometry (LC-MS/MS) method was developed and applied. The 6-plex screening showed discrepancies with the LC-MS/MS analysis, possibly due to matrix interference and/or the presence of unknown mycotoxin metabolites. The major mycotoxins detected were DON and its plant metabolite deoxynivalenol-3-β-D-glucopyranoside (D3G). The 6-plex immunoassay reported the sum of DON and D3G (DON+D3G) contaminations ranging from 10 to 475 μg/L in 406 beers, of which 73% were craft beers. The popular craft beer style imperial stout, had the highest percentage of samples suspected positive (83%) with 29% of all imperial stout beers having DON+D3G contaminations above 100 μg/L. LC-MS/MS analysis showed that industrial pale lagers from Italy and Spain, predominantly contained FBs (3–69 μg/L). Besides FBs, African traditional beers also contained aflatoxins (0.1–1.2 μg/L). The presence of OTA, T-2, HT-2, ZEN, β-zearalenol, 3/15-acetyl-DON, nivalenol and the conjugated mycotoxin zearalenone 14-sulfate were confirmed in some beers. This study shows that in 27 craft beers, DON+D3G concentrations occurred above (or at) the Tolerable Daily Intake (TDI). Exceeding the TDI, may have a health impact. A better control of brewing malts for craft beer, should be put in place to circumvent this potential

  7. Mycotoxin profiling of 1000 beer samples with a special focus on craft beer.

    Directory of Open Access Journals (Sweden)

    Jeroen Peters

    Full Text Available Currently beer is booming, mainly due to the steady rise of craft breweries worldwide. Previous surveys for occurrence of mycotoxins in beer, were mainly focussed on industrial produced beer. The present survey reports the presence of mycotoxins in craft beer and how this compares to industrial produced beer. More than 1000 beers were collected from 47 countries, of which 60% were craft beers. A selection of 1000 samples were screened for the presence of aflatoxin B1, ochratoxin A (OTA, zearalenone (ZEN, fumonisins (FBs, T-2 and HT-2 toxins (T-2 and HT-2 and deoxynivalenol (DON using a mycotoxin 6-plex immunoassay. For confirmatory analysis, a liquid chromatography tandem mass spectrometry (LC-MS/MS method was developed and applied. The 6-plex screening showed discrepancies with the LC-MS/MS analysis, possibly due to matrix interference and/or the presence of unknown mycotoxin metabolites. The major mycotoxins detected were DON and its plant metabolite deoxynivalenol-3-β-D-glucopyranoside (D3G. The 6-plex immunoassay reported the sum of DON and D3G (DON+D3G contaminations ranging from 10 to 475 μg/L in 406 beers, of which 73% were craft beers. The popular craft beer style imperial stout, had the highest percentage of samples suspected positive (83% with 29% of all imperial stout beers having DON+D3G contaminations above 100 μg/L. LC-MS/MS analysis showed that industrial pale lagers from Italy and Spain, predominantly contained FBs (3-69 μg/L. Besides FBs, African traditional beers also contained aflatoxins (0.1-1.2 μg/L. The presence of OTA, T-2, HT-2, ZEN, β-zearalenol, 3/15-acetyl-DON, nivalenol and the conjugated mycotoxin zearalenone 14-sulfate were confirmed in some beers. This study shows that in 27 craft beers, DON+D3G concentrations occurred above (or at the Tolerable Daily Intake (TDI. Exceeding the TDI, may have a health impact. A better control of brewing malts for craft beer, should be put in place to circumvent this potential

  8. Mycotoxin profiling of 1000 beer samples with a special focus on craft beer.

    Science.gov (United States)

    Peters, Jeroen; van Dam, Ruud; van Doorn, Ronald; Katerere, David; Berthiller, Franz; Haasnoot, Willem; Nielen, Michel W F

    2017-01-01

    Currently beer is booming, mainly due to the steady rise of craft breweries worldwide. Previous surveys for occurrence of mycotoxins in beer, were mainly focussed on industrial produced beer. The present survey reports the presence of mycotoxins in craft beer and how this compares to industrial produced beer. More than 1000 beers were collected from 47 countries, of which 60% were craft beers. A selection of 1000 samples were screened for the presence of aflatoxin B1, ochratoxin A (OTA), zearalenone (ZEN), fumonisins (FBs), T-2 and HT-2 toxins (T-2 and HT-2) and deoxynivalenol (DON) using a mycotoxin 6-plex immunoassay. For confirmatory analysis, a liquid chromatography tandem mass spectrometry (LC-MS/MS) method was developed and applied. The 6-plex screening showed discrepancies with the LC-MS/MS analysis, possibly due to matrix interference and/or the presence of unknown mycotoxin metabolites. The major mycotoxins detected were DON and its plant metabolite deoxynivalenol-3-β-D-glucopyranoside (D3G). The 6-plex immunoassay reported the sum of DON and D3G (DON+D3G) contaminations ranging from 10 to 475 μg/L in 406 beers, of which 73% were craft beers. The popular craft beer style imperial stout, had the highest percentage of samples suspected positive (83%) with 29% of all imperial stout beers having DON+D3G contaminations above 100 μg/L. LC-MS/MS analysis showed that industrial pale lagers from Italy and Spain, predominantly contained FBs (3-69 μg/L). Besides FBs, African traditional beers also contained aflatoxins (0.1-1.2 μg/L). The presence of OTA, T-2, HT-2, ZEN, β-zearalenol, 3/15-acetyl-DON, nivalenol and the conjugated mycotoxin zearalenone 14-sulfate were confirmed in some beers. This study shows that in 27 craft beers, DON+D3G concentrations occurred above (or at) the Tolerable Daily Intake (TDI). Exceeding the TDI, may have a health impact. A better control of brewing malts for craft beer, should be put in place to circumvent this potential problem.

  9. The role of work-related needs in the relationship between job crafting, burnout and engagement

    Directory of Open Access Journals (Sweden)

    Fabrice Travaglianti

    2016-04-01

    Full Text Available Orientation: Knowing that it is imperative to better understand the antecedents and consequences of needs-supplies fit, the present research had two main objectives. Firstly we wanted to extend our knowledge about traditional psychological needs, for example highlighted through the Self-Determination Theory, by presenting more specific work-related needs. Secondly, following the new directions of organisational fit theories, we wanted to better understand how individuals make sense of fit.Research purpose: The purpose of this study is to propose more specific work-related needs in terms of employment quality and to test job crafting as an antecedent of needs-supplies fit (NS fit. We tested the double mediating role of NS fit (i.e. specific: based on more specific work-related needs, and general: based on global job perceptions between job crafting and individual outcomes namely burnout and work engagement.Motivation for the study: By taking into account more specific work-related needs, this study aimed to add more specific information to better help predict well-being at work. Moreover, the present research responds to the need to better understand how individuals make sense of fit.Research design, approach, and method: Data were collected in a Belgian Public Federal Service (N = 1500. Our research model was tested using Structural Equation Modelling with Mplus.Main findings: Results show, (1 that specific NS fit perception was positively related to a global NS fit perception and (2 the partial mediating role (specific and general of NS fit between job crafting and burnout and work engagement.Practical/managerial implications: Managers should encourage crafting behaviours and should know their team and that team’s specific needs.Contribution/added-value: By taking into account more specific work-related needs, our study suggests that needs-supplies may have more than one dimension. Moreover, it shows that job crafting is a way to increase NS

  10. Children Designing a Soft Toy. An LCE model as an application of the experiential learning during the holistic craft process

    Directory of Open Access Journals (Sweden)

    Marja-Leena Rönkkö

    2015-02-01

    Full Text Available In a holistic craft process, the same person designs a visual and technical appearance, produces the design with craft materials and technologies, make necessary changes to the design during its production and finally assesses the process and the finished product. Similarly, in the educational context, students should make craft products starting with the design process. These kinds of designing and hands-on activities nurture students’ creativity and problem-solving skills and offer them an opportunity to test their ideas and see them realised. Testing and further developing pedagogical approaches to holistic craft is important from the perspective of the renewal of the national core curriculum (2016 in Finland, which emphasises holistic approaches and the integration of different content areas. This study presents an experiential learning model of combining literature education, ethic-moral education and craft. Kolb’s model of experiential learning gives a solid and systematic theoretical base for this LCE model (one combining literature, craft and ethic-moral education. The teaching experiment is implemented as a craft process supported with children’s literature and activities based on a story. It seems that children can derive benefit from literature and activities during a craft making process. In addition, referencing literature enables the teacher to combine the craft process with multiple learning targets, fostering both ethical and content skills. We present the LCE model both in the light of an experiential learning model and the pragmatic implementations it gives rise to. According to our experiments, experiential learning can be meaningfully applied to the holistic craft process and craft education. Furthermore, the LCE model helps students to commit to holistic craft by nurturing a personal attachment. Normal 0 21 false false false FI X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso

  11. Brewing with Distinction: The Implications of a Quality Symbol for the Craft Beer Industry of British Columbia

    OpenAIRE

    Oppenheimer, Leonardo Manuel

    2008-01-01

    A growing segment of the Canadian beer market is the microbrew/craft beer segment. For the palates of many beer connoisseurs, craft beer has a taste that distinguishes it from other beers, thus setting it apart from the mass-marketed products of the giant commercial breweries. However, a large proportion of beer consumers in Canada remain oblivious to the virtues and properties that make craft beer unique. This study examines the feasibility of creating a quality symbol of distinction as a me...

  12. Medications for the treatment of motion sickness during evacuation, escape and rescue offshore

    Energy Technology Data Exchange (ETDEWEB)

    Coleshaw, S.R.K.

    1996-06-01

    A high incidence of seasickness has been recorded amongst survivors of accidents occurring offshore, whether in lifeboats or in the water. Illness is prevalent in relatively calm seas as well as conditions of severe wind and wave. When considering the occupants of totally enclosed motor propelled survival craft (TEMPSC), then the shape and design of the vessel, the lack of visual cues, the lack of forward facing seats and head restraint, the smell, and the view of others being sick are all factors which exacerbate the problem. The majority of drugs used in the treatment of nausea and vomiting are given in advance, to prevent the development of symptoms. Of the anti-emetic agents currently available, scopolamine is thought to be the most effective drug, both for the prophylaxis and treatment of seasickness. To achieve therapeutic levels quickly, and then maintain the treatment, a combination of preparations are indicated; an initial dose given by buccal tablet or injection followed by a transdermal patch to ensure long-term effectiveness. (author)

  13. A review of new developments in the Friedel-Crafts alkylation - From green chemistry to asymmetric catalysis.

    Science.gov (United States)

    Rueping, Magnus; Nachtsheim, Boris J

    2010-01-20

    The development of efficient Friedel-Crafts alkylations of arenes and heteroarenes using only catalytic amounts of a Lewis acid has gained much attention over the last decade. The new catalytic approaches described in this review are favoured over classical Friedel-Crafts conditions as benzyl-, propargyl- and allyl alcohols, or styrenes, can be used instead of toxic benzyl halides. Additionally, only low catalyst loadings are needed to provide a wide range of products. Following a short introduction about the origin and classical definition of the Friedel-Crafts reaction, the review will describe the different environmentally benign substrates which can be applied today as an approach towards greener processes. Additionally, the first diastereoselective and enantioselective Friedel-Crafts-type alkylations will be highlighted.

  14. A review of new developments in the Friedel–Crafts alkylation – From green chemistry to asymmetric catalysis

    Directory of Open Access Journals (Sweden)

    Magnus Rueping

    2010-01-01

    Full Text Available The development of efficient Friedel–Crafts alkylations of arenes and heteroarenes using only catalytic amounts of a Lewis acid has gained much attention over the last decade. The new catalytic approaches described in this review are favoured over classical Friedel–Crafts conditions as benzyl-, propargyl- and allyl alcohols, or styrenes, can be used instead of toxic benzyl halides. Additionally, only low catalyst loadings are needed to provide a wide range of products. Following a short introduction about the origin and classical definition of the Friedel–Crafts reaction, the review will describe the different environmentally benign substrates which can be applied today as an approach towards greener processes. Additionally, the first diastereoselective and enantioselective Friedel–Crafts-type alkylations will be highlighted.

  15. A comparison study on the deck house shape of high speed planing crafts for air resistance reduction

    Directory of Open Access Journals (Sweden)

    Park Chung-Hwan

    2014-12-01

    Full Text Available Planing crafts were specifically designed to achieve relatively high speeds on the water. When a planing craft is running at high speed, dynamic pressure on the bottom makes the boat rise on the surface of the water. This reduces the area of the sinking surface of the boat to increase air resistance. Air resistance means the resistance that occurs when the hull and deck house over the surface of the water come in contact with the air current. In this paper, we carried out a CFD numerical analysis to find optimal deck houses that decreased air-resistance on the water when planing crafts are running at high speed. We finally developed the deck house shape of high-speed planing crafts that optimally decreased air resistance.

  16. Development Strategy for Continuous Professional Education in the Field of Traditional Applied Arts and Crafts of Russia

    Directory of Open Access Journals (Sweden)

    O V Fedotova

    2011-12-01

    Full Text Available The major factors of the development and perfection of the education system in the field of traditional applied arts and crafts in view of modern requirements are considered in the article.

  17. Ocean disposal of dredged materials from Atlantic Canadian harbours. 1. Small craft harbours, Scotia-Fundy Region

    National Research Council Canada - National Science Library

    1985-01-01

    The objective of this report is to provide a compilation of all data related to dredging/ocean disposal of dredged materials from harbours maintained by the Small Craft Harbours Branch of Fisheries...

  18. Three-Point Flexural Properties of Bonded Reinforcement Elements for Pleasure Craft Decks

    Science.gov (United States)

    Di Bella, G.; Galtieri, G.; Borsellino, C.

    2017-04-01

    The aim of this work was both to study the performances of pleasure craft reinforced components, bonded using a structural adhesive, and to compare them with those obtained using over-lamination as joining system, typically employed in the shipbuilding. With such aim, two different lots of components were prepared: in the first lot, the reinforcement structures were laminated directly on the investigated composite components and, in the second one; they were made separately in a mould and, then, bonded to the composite components. This last method allowed to evaluate the introduction of a product/process innovation in a field typically unwilling to innovation, still tied to craft, and non-standardized procedures. The results of bending tests, performed in order to evaluate the mechanical behaviour of the reinforced components, evidenced the goodness of this innovative design choice. Finally, a finite element analysis was performed.

  19. Combining Hand-crafted Rules and Unsupervised Learning in Constraint-based Morphological Disambiguation

    CERN Document Server

    Oflazer, K; Oflazer, Kemal; Tur, Gokhan

    1996-01-01

    This paper presents a constraint-based morphological disambiguation approach that is applicable languages with complex morphology--specifically agglutinative languages with productive inflectional and derivational morphological phenomena. In certain respects, our approach has been motivated by Brill's recent work, but with the observation that his transformational approach is not directly applicable to languages like Turkish. Our system combines corpus independent hand-crafted constraint rules, constraint rules that are learned via unsupervised learning from a training corpus, and additional statistical information from the corpus to be morphologically disambiguated. The hand-crafted rules are linguistically motivated and tuned to improve precision without sacrificing recall. The unsupervised learning process produces two sets of rules: (i) choose rules which choose morphological parses of a lexical item satisfying constraint effectively discarding other parses, and (ii) delete rules, which delete parses sati...

  20. CRAFTING THE MICROWORLD: HOW ROBERT HOOKE CONSTRUCTED KNOWLEDGE ABOUT SMALL THINGS.

    Science.gov (United States)

    Lawson, Ian

    2016-03-20

    This paper investigates the way in which Robert Hooke constructed his microscopical observations. His Micrographia is justifiably famous for its detailed engravings, which communicated Hooke's observations of tiny nature to his readers, but less attention has been paid to how he went about making the observations themselves. In this paper I explore the relationship between the materiality of his instrument and the epistemic images he produced. Behind the pictures lies an array of hidden materials, and the craft knowledge it took to manipulate them. By investigating the often counter-theoretical and conflicting practices of his ingenious microscope use, I demonstrate the way in which Hooke crafted the microworld for his readers, giving insight into how early modern microscopy was understood by its practitioners and audience.

  1. Creativity in the Bronze Age: bringing archaeological research into contemporary craft teaching and learning through a live project

    OpenAIRE

    Persad, Rachel; Sofaer, Joanna

    2016-01-01

    The CinBA Live Project sought to engage students of contemporary craft courses in the UK with Bronze Age creativity. We aimed to explore the ways in which the creativity inherent in prehistoric craft may be used as inspiration in contemporary making. It simultaneously offered institutions a unique opportunity to offer a practice-led, research-based live project which was distinct to those generally known to be available to art and design institutions. It offered a different experience within ...

  2. The historic working small craft of South Carolina : a general typology with a study of adaptations of flatboat design

    OpenAIRE

    Newell, Mark M.

    1997-01-01

    The following dissertation presents a typology for historic working watercraft of the State of South Carolina, United States of America. The background investigation for this typology addressed research design questions concerning the geographic and ethnic origins of the builders of these craft, the history of transportation growth in the area and other factors which are thought to have influenced basic design, and construction methods. These factors were the environments in which craft opera...

  3. A Guide for Measuring, Analyzing, and Evaluating Accelerations Recorded During Seakeeping Trials of High-Speed Craft

    Science.gov (United States)

    2016-01-01

    Naval Surface Warfare Center Carderock Division West Bethesda, MD 20817-5700 NSWCCD-80-TR-2016/003 January 2016 Naval Architecture and...ADMINISTRATIVE INFORMATION This report was prepared by the Combatant Craft Division (CCD, Code 83) of the Naval Architecture and Engineering Department at...or small craft with their sensory perceptions of heave, surge, sway, pitch, roll, and yaw, as well as the linear and rotational rates of change of

  4. The role of big five factors on predicting job crafting propensities amongst administrative employees in a South African tertiary institution

    Directory of Open Access Journals (Sweden)

    Clement Bell

    2016-02-01

    Full Text Available Orientation: Personality provides a foundation for understanding employee job behaviours. It determines and reflects how they respond to their work situations. There is a shortage of previous researches that have specifically dealt with the predictive role of personality on job crafting. Job crafting is also a significantly new concept in the South African work context. It has both positive and negative consequences on employee job behaviours.Research purpose: The present study investigated the role of big five factors on predicting job crafting propensities amongst administrative employees in Alice, South Africa.Motivation for the study: The present study aimed to determine the role of big five factors on predicting job crafting propensities amongst administrative employees. It was premised on previous research that the big five factors are associated with many employee job behaviours.Research approach, design and method: The present study employed a quantitative, crosssectional research design with a sample of 246 administrative employees in Alice, South Africa. A biographical questionnaire, a Big Five Inventory, and a job crafting questionnaire were used to collect data.Main findings: The findings showed that big five factors of Conscientiousness, Extraversion, Agreeableness, Openness to experience and Neuroticism play a significant role in predicting job crafting propensities.Practical implications: The present study suggests that big five factors of Conscientiousness, Extraversion, Agreeableness, Openness to experience and Neuroticism have a predictive role on job crafting behaviours. Managers of tertiary institutions can therefore consider these big five personalities to understand and predict the impacts of their job design strategies on administrative employees’ behaviours.Contribution: The contribution of the study was significant in that it contributed to research literature representing the influence of the big five factors in

  5. The relationship crafts- design through jewelry. A historical-technical perspective

    OpenAIRE

    Medina-Gómez, Andrea; Hernandis Ortuño, Bernabé

    2012-01-01

    This article discusses relationships and contemporary jewelry components from the crafts perspective, an evolutionary view in which design is seen as a tool to promote materials, techniques, and their connotations. It addresses a basic taxonomy and concepts of craftsmanship in the European and Latin American contexts, in order to evaluate a contemporary definition of jewelry, the influence of the materials on their connotations, the importance of ...

  6. Carlo Ginzburg and the Historian’s Craft: Questions and Remarks

    Directory of Open Access Journals (Sweden)

    Giovanni Tarantino

    2014-03-01

    Full Text Available Selected paper from the first edition of IinteR-La+b (the International Interdisciplinary Research Laboratory of the Accademia Nazionale dei Lincei, the Swiss Academies of Arts and Sciences and the Balzan Foundation held in Rome, at the Accademia Nazionale dei Lincei, 12–13 November 2012. Published in Giovanni Tarantino (ed., “Our words, and theirs:” A conversation with Carlo Ginzburg on the historian’s craft, Cromohs 18 (2013.

  7. Job Crafting: Older Workers' Mechanism for Maintaining Person-Job Fit.

    Science.gov (United States)

    Wong, Carol M; Tetrick, Lois E

    2017-01-01

    Aging at work is a dynamic process. As individuals age, their motives, abilities and values change as suggested by life-span development theories (Lang and Carstensen, 2002; Kanfer and Ackerman, 2004). Their growth and extrinsic motives weaken while intrinsic motives increase (Kooij et al., 2011), which may result in workers investing their resources in different areas accordingly. However, there is significant individual variability in aging trajectories (Hedge et al., 2006). In addition, the changing nature of work, the evolving job demands, as well as the available opportunities at work may no longer be suitable for older workers, increasing the likelihood of person-job misfit. The potential misfit may, in turn, impact how older workers perceive themselves on the job, which leads to conflicting work identities. With the traditional job redesign approach being a top-down process, it is often difficult for organizations to take individual needs and skills into consideration and tailor jobs for every employee (Berg et al., 2010). Therefore, job crafting, being an individualized process initiated by employees themselves, can be a particularly valuable mechanism for older workers to realign and enhance their demands-abilities and needs-supplies fit. Through job crafting, employees can exert personal agency and make changes to the task, social and cognitive aspects of their jobs with the goal of improving their work experience (Wrzesniewski and Dutton, 2001). Building on the Life Span Theory of Control (Heckhausen and Schulz, 1995), we posit that job crafting, particularly cognitive crafting, will be of increasing value as employees age. Through reframing how they think of their job and choosing to emphasize job features that are personally meaningful, older workers can optimize their resources to proactively redesign their jobs and maintain congruent, positive work identities.

  8. Job Crafting: Older Workers’ Mechanism for Maintaining Person-Job Fit

    Directory of Open Access Journals (Sweden)

    Carol M. Wong

    2017-09-01

    Full Text Available Aging at work is a dynamic process. As individuals age, their motives, abilities and values change as suggested by life-span development theories (Lang and Carstensen, 2002; Kanfer and Ackerman, 2004. Their growth and extrinsic motives weaken while intrinsic motives increase (Kooij et al., 2011, which may result in workers investing their resources in different areas accordingly. However, there is significant individual variability in aging trajectories (Hedge et al., 2006. In addition, the changing nature of work, the evolving job demands, as well as the available opportunities at work may no longer be suitable for older workers, increasing the likelihood of person-job misfit. The potential misfit may, in turn, impact how older workers perceive themselves on the job, which leads to conflicting work identities. With the traditional job redesign approach being a top-down process, it is often difficult for organizations to take individual needs and skills into consideration and tailor jobs for every employee (Berg et al., 2010. Therefore, job crafting, being an individualized process initiated by employees themselves, can be a particularly valuable mechanism for older workers to realign and enhance their demands-abilities and needs-supplies fit. Through job crafting, employees can exert personal agency and make changes to the task, social and cognitive aspects of their jobs with the goal of improving their work experience (Wrzesniewski and Dutton, 2001. Building on the Life Span Theory of Control (Heckhausen and Schulz, 1995, we posit that job crafting, particularly cognitive crafting, will be of increasing value as employees age. Through reframing how they think of their job and choosing to emphasize job features that are personally meaningful, older workers can optimize their resources to proactively redesign their jobs and maintain congruent, positive work identities.

  9. Tetranuclear 3d/4f coordination clusters as highly efficient catalysts for Friedel Crafts alkylation

    OpenAIRE

    Griffiths, Kieran; Kumar, Prashant; Akien, Geoffrey R.; Chilton, Nicholas F; Abdul-Sada, Alaa; Tizzard, Graham J; Simon J. Coles; Kostakis, George E.

    2016-01-01

    A series of custom-designed, high yield, isoskeletal tetranuclear Zn/4f coordination clusters showing high efficiency as catalysts with low catalytic loadings in Friedel-Crafts alkylation are described for the first time. The possibility of altering the 4f centers in these catalysts without altering the core topology allows us to further confirm their stability via EPR and NMR, as well to gain insights into the plausible reaction mechanism, showcasing the usefulness of these bimetallic system...

  10. Tetranuclear Zn/4f coordination clusters as highly efficient catalysts for Friedel–Crafts alkylation

    OpenAIRE

    Griffiths, Kieran; Kumar, Prashant; Akien, Geoffrey R.; Chilton, Nicholas F; Abdul-Sada, Alaa; Tizzard, Graham; Coles, Simon; Kostakis, George E.

    2016-01-01

    A series of custom-designed, high yield, isoskeletal tetranuclear Zn/4f coordination clusters showing high efficiency as catalysts with low catalytic loadings in Friedel–Crafts alkylation are described for the first time. The possibility of altering the 4f centers in these catalysts without altering the core topology allows us to further confirm their stability via EPR and NMR, as well to gain insights into the plausible reaction mechanism, showcasing the usefulness of these bimetallic system...

  11. Notes about “Art as a Vehicle” and the Alchemical Craft of the Performer

    Directory of Open Access Journals (Sweden)

    Cassiano Sydow Quilici

    2013-03-01

    Full Text Available The article discusses how Grotowski thinks the craft of the performer inspired by the dialogue with spiritual traditions. I focus on some concepts and metaphors found in his research about verticality, especially the idea of transforming a common experience into a subtle one. I establish comparisons with some alchemical principles and discuss the use of symbols such as Jacob’s ladder in his work. Finally, I approach the connection between structure and spontaneity.

  12. Brynmawr experiment 1928-1940 : Quaker values and arts and crafts principles

    OpenAIRE

    Manasseh, Pamela

    2009-01-01

    This is a study of the social work of Quakers in the town of Brynmawr in South Wales during the depressions of the 1920s and 1930s. The work, which took place during the years 1928 to 1940, has become known as the Brynmawr Experiment. The initial provision of practical and financial relief for a town suffering severely from the effects of unemployment, was developed with the establishment of craft workshops to provide employment. Special reference is made to the furniture makin...

  13. From Dalek half balls to Daft Punk helmets: Mimetic fandom and the crafting of replicas

    OpenAIRE

    Matt Hills

    2014-01-01

    Mimetic fandom is a surprisingly understudied mode of (culturally masculinized) fan activity in which fans research and craft replica props. Mimetic fandom can be considered as (in)authentic and (im)material, combining noncommercial status with grassroots marketing or brand reinforcement as well as fusing an emphasis on material artifacts with Web 2.0 collective intelligence. Simply analyzing mimetic fandom as part of fannish material culture fails to adequately assess the nonmaterial aspects...

  14. Classification of radiolarian images with hand-crafted and deep features

    Science.gov (United States)

    Keçeli, Ali Seydi; Kaya, Aydın; Keçeli, Seda Uzunçimen

    2017-12-01

    Radiolarians are planktonic protozoa and are important biostratigraphic and paleoenvironmental indicators for paleogeographic reconstructions. Radiolarian paleontology still remains as a low cost and the one of the most convenient way to obtain dating of deep ocean sediments. Traditional methods for identifying radiolarians are time-consuming and cannot scale to the granularity or scope necessary for large-scale studies. Automated image classification will allow making these analyses promptly. In this study, a method for automatic radiolarian image classification is proposed on Scanning Electron Microscope (SEM) images of radiolarians to ease species identification of fossilized radiolarians. The proposed method uses both hand-crafted features like invariant moments, wavelet moments, Gabor features, basic morphological features and deep features obtained from a pre-trained Convolutional Neural Network (CNN). Feature selection is applied over deep features to reduce high dimensionality. Classification outcomes are analyzed to compare hand-crafted features, deep features, and their combinations. Results show that the deep features obtained from a pre-trained CNN are more discriminative comparing to hand-crafted ones. Additionally, feature selection utilizes to the computational cost of classification algorithms and have no negative effect on classification accuracy.

  15. Deep Visual Attributes vs. Hand-Crafted Audio Features on Multidomain Speech Emotion Recognition

    Directory of Open Access Journals (Sweden)

    Michalis Papakostas

    2017-06-01

    Full Text Available Emotion recognition from speech may play a crucial role in many applications related to human–computer interaction or understanding the affective state of users in certain tasks, where other modalities such as video or physiological parameters are unavailable. In general, a human’s emotions may be recognized using several modalities such as analyzing facial expressions, speech, physiological parameters (e.g., electroencephalograms, electrocardiograms etc. However, measuring of these modalities may be difficult, obtrusive or require expensive hardware. In that context, speech may be the best alternative modality in many practical applications. In this work we present an approach that uses a Convolutional Neural Network (CNN functioning as a visual feature extractor and trained using raw speech information. In contrast to traditional machine learning approaches, CNNs are responsible for identifying the important features of the input thus, making the need of hand-crafted feature engineering optional in many tasks. In this paper no extra features are required other than the spectrogram representations and hand-crafted features were only extracted for validation purposes of our method. Moreover, it does not require any linguistic model and is not specific to any particular language. We compare the proposed approach using cross-language datasets and demonstrate that it is able to provide superior results vs. traditional ones that use hand-crafted features.

  16. Effects of a job crafting intervention program on work engagement among Japanese employees: a pretest-posttest study.

    Science.gov (United States)

    Sakuraya, Asuka; Shimazu, Akihito; Imamura, Kotaro; Namba, Katsuyuki; Kawakami, Norito

    2016-10-24

    Job crafting, an employee-initiated job design/redesign, has become important for employees' well-being such as work engagement. This study examined the effectiveness of a newly developed job crafting intervention program on work engagement (as primary outcome), as well as job crafting and psychological distress (as secondary outcomes), using a pretest-posttest study design among Japanese employees. Participants were managers of a private company and a private psychiatric hospital in Japan. The job crafting intervention program consisted of two 120-min sessions with a two-week interval between them. Outcomes were assessed at baseline (Time 1), post-intervention (Time 2), and a one-month follow-up (Time 3). The mixed growth model analyses were conducted using time (Time 1, Time 2, and Time 3) as an indicator of intervention effect. Effect sizes were calculated using Cohen's d. The program showed a significant positive effect on work engagement (t = 2.20, p = 0.03) in the mixed growth model analyses, but with only small effect sizes (Cohen's d = 0.33 at Time 2 and 0.26 at Time 3). The program also significantly improved job crafting (t = 2.36, p = 0.02: Cohen's d = 0.36 at Time 2 and 0.47 at Time 3) and reduced psychological distress (t = -2.06, p = 0.04: Cohen's d = -0.15 at Time 2 and -0.31 at Time 3). The study indicated that the newly developed job crafting intervention program was effective in increasing work engagement, as well as in improving job crafting and decreasing psychological distress, among Japanese managers. UMIN Clinical Trials Registry UMIN000024062 . Retrospectively registered 15 September 2016.

  17. Who Seeks Job Resources, and Who Avoids Job Demands? The Link Between Dark Personality Traits and Job Crafting.

    Science.gov (United States)

    Roczniewska, Marta; Bakker, Arnold B

    2016-10-08

    Although job crafting has been linked repeatedly to positive employee and organizational outcomes, its detrimental side has not been well explored. To understand the way dark personality traits affect the type of crafting in which employees engage, this research focuses on two frameworks: the PEN (psychopathy, extraversion, and neuroticism) framework and the Dark Triad (narcissism, psychopathy, and Machiavellianism). In Study 1, we collected data on the PEN traits and job crafting from 155 individuals in various occupations. We found that neuroticism was negatively related to seeking structural job resources, whereas psychoticism was negatively related to seeking social job resources. We also found that extraversion was positively related to seeking structural and social job resources and to seeking challenging job demands. In Study 2, we examined how the Dark Triad traits predicted job crafting among police officers (N = 135). The results showed that narcissism was positively related to seeking social job resources and challenges, whereas psychopathy was negatively related to seeking social resources. Age and narcissism were positive predictors of reducing job demands. We conclude that personality plays an important role when choosing how to craft one's job. We discuss the practical implications of these findings.

  18. A Vision-Based Method for Autonomous Landing of a Rotor-Craft Unmanned Aerial Vehicle

    Directory of Open Access Journals (Sweden)

    Z. Yuan

    2006-01-01

    Full Text Available This article introduces a real-time vision-based method for guided autonomous landing of a rotor-craft unmanned aerial vehicle. In the process of designing the pattern of landing target, we have fully considered how to make this easier for simplified identification and calibration. A linear algorithm was also applied using a three-dimensional structure estimation in real time. In addition, multiple-view vision technology is utilized to calibrate intrinsic parameters of camera online, so calibration prior to flight is unnecessary and the focus of camera can be changed freely in flight, thus upgrading the flexibility and practicality of the method.

  19. Highly enantioselective Friedel-Crafts reaction of thiophenes with glyoxylates: formal synthesis of duloxetine.

    Science.gov (United States)

    Majer, Jakub; Kwiatkowski, Piotr; Jurczak, Janusz

    2009-10-15

    An efficient Friedel-Crafts reaction of a series of 2-substituted thiophenes with alkyl glyoxylates has been developed using a catalytic amount of an easy accessible 6,6'-dibromo-BINOL/Ti(IV) complex. A variety of hydroxy(thiophene-2-yl)acetates can be synthesized in high enantioselectivites (92-98% ee) and good yields. This is the first report on the efficient asymmetric F-C reaction of thiophenes with alkyl glyoxylates. Starting from simple thiophene and n-butyl glyoxylate, we demonstrated the formal synthesis of duloxetine.

  20. Teaching Quantum Mechanics with qCraft: Outreach and Video Games

    Science.gov (United States)

    Kubica, Aleksander; Chatwin-Davies, Aidan; Michalakis, Spyridon

    Why is quantum mechanics considered a hard and inaccessible subject? Part of the difficulty is due to the nature of the subject itself. However, no small part of the difficulty is its pedagogy, which often relies on out-of-date historical motivation and experimental evidence that is disconnected from day-to-day experiences. In this first talk, we explore ways in which video games are well-suited to teaching quantum mechanics, in particular with regards to building intuition, as well as some of their limitations. We then illustrate these considerations through qCraft, an extension for Minecraft that incorporates aspects of quantum mechanics into the game.

  1. Profession or craft? A reflection on the moral identity of social work

    Directory of Open Access Journals (Sweden)

    Ed de Jonge

    2014-03-01

    Full Text Available Profession or craft? A reflection on the moral identity of social workWhat is the occupational identity of social work, and what should it be? Social work is sometimes characterized as a profession and sometimes as a craft, very often without a clear distinction being made between these two categories – and possibly without realizing that a difference exists. An ideal-typical approach, however, may be helpful in clarifying not only the many similarities but also the fundamental differences between these two types of occupations. Following Freidson (2001 and Sennett (2008, it can be shown that the ideal-typical focus of a profession is realizing an abstract value (like justice, whereas a craft will centre on manipulating a concrete material (such as stone. As such, professions – and only professions – are occupations with a moral identity. This moral identity, this humanitarian mission can be found in all self-definitions of social work (e.g. IFSW, NVMW. Social work should therefore be regarded as a profession and not as a craft. This is not merely an academic discussion but impacts on the position of the occupation in society, as recent developments in the Netherlands concerning the new style of welfare (“Welzijn Nieuwe Stijl” illustrate.Professie of ambacht? Een reflectie over de morele beroepsidentiteit van sociaal werk Wat is de beroepsidentiteit van sociaal werk, wat behoort zij te zijn? Sociaal werk wordt wel omschreven als een professie maar ook als een ambacht, vaak zonder duidelijk onderscheid tussen en wellicht zelfs door impliciete gelijkstelling van deze kwalificaties. Met behulp van de ideaaltypische benadering kan echter worden aangetoond dat deze twee typen beroepen niet alleen veel overeenkomsten delen maar ook op enkele punten fundamenteel van elkaar verschillen. Op basis van het werk van Freidson (2001 en Sennett (2008 kan worden aangetoond dat het ideaaltypische doel van professies het realiseren van een abstracte

  2. 3D technology in fine art and craft exploring 3D printing, scanning, sculpting and milling

    CERN Document Server

    Mongeon, Bridgette

    2015-01-01

    The possibilities for creation are endless with 3D printing, sculpting, scanning, and milling, and new opportunities are popping up faster than artists can keep up with them. 3D Technology in Fine Art and Craft takes the mystery out of these exciting new processes by demonstrating how to navigate their digital components and showing their real world applications. Artists will learn to incorporate these new technologies into their studio work and see their creations come to life in a physical form never before possible. Featuring a primer on 3D basics for beginners,interviews, tutorials, and ar

  3. Technology for future low-pollution air-craft gas turbines. Technologie fuer kuenftige schadstoffarme Luftfahrtgasturbinen

    Energy Technology Data Exchange (ETDEWEB)

    Weyer, H.B. (Inst. fuer Antriebstechnik, Deutsche Forschungsanstalt fuer Luft- und Raumfahrt e.V. (DLR), Koeln (Germany))

    1992-01-01

    The author highlights the state of the art and development of aviation and the resulting atmospheric pollution with a special reference to civilian air traffic at cruising altitude. The propagation and long-term chemical effect of power-unit exhaust gases are not discussed; these complex processes of diffusion and atmospheric chemistry are dealt with in papers of their own. The author focusses on future aviation technologies which will improve the pollutivity and profitability of air-craft while maintaining their high level of operational safety. (orig.)

  4. Accounting for taste:conversation, categorisation and certification in the sensory assessment of craft brewing

    OpenAIRE

    Wright, Steve

    2014-01-01

    The recent rapid growth of “craft beer” has led to a search for definitions and categorisation of that sector with “beer style” used as one criterion. This thesis explores the origins of these style definitions and how they act as a technology of classification which affects how sensory judgments are formed and expressed in practice, and how judges are examined and certified. The investigation draws on actor-network theory and ethnomethodology to trace how taste descriptions are assembled and...

  5. Thesaurus of craft and professional terminology in Ukrainian bibliopegy: the issues of a special dictionary formation

    Directory of Open Access Journals (Sweden)

    Halchenko O.

    2015-01-01

    Full Text Available The article covers terminological problems which arise when medieval manuscripts’ bindings are described for scientific catalogs and electronic databases. The author attempts to analyze the causes of these problems and ways to overcome them. Reviewed are handwritten and printed sources, which contain the terms dealing with manuscripts production, and substantiated is the relevance of formation of the national craft and professional terminology thesaurus in Ukrainian codicology and bibliopegy. We have also defined the basic steps of the dictionary creation, which are the following: collecting special terms and creating a glossary and card index; translation, editing and unification of borrowed terms; creation of a digital visual dictionary

  6. Comparison of hand-craft feature based SVM and CNN based deep learning framework for automatic polyp classification.

    Science.gov (United States)

    Younghak Shin; Balasingham, Ilangko

    2017-07-01

    Colonoscopy is a standard method for screening polyps by highly trained physicians. Miss-detected polyps in colonoscopy are potential risk factor for colorectal cancer. In this study, we investigate an automatic polyp classification framework. We aim to compare two different approaches named hand-craft feature method and convolutional neural network (CNN) based deep learning method. Combined shape and color features are used for hand craft feature extraction and support vector machine (SVM) method is adopted for classification. For CNN approach, three convolution and pooling based deep learning framework is used for classification purpose. The proposed framework is evaluated using three public polyp databases. From the experimental results, we have shown that the CNN based deep learning framework shows better classification performance than the hand-craft feature based methods. It achieves over 90% of classification accuracy, sensitivity, specificity and precision.

  7. Organocatalytic asymmetric Friedel-Crafts reaction of sesamol with isatins: access to biologically relevant 3-aryl-3-hydroxy-2-oxindoles.

    Science.gov (United States)

    Kumar, Akshay; Kaur, Jasneet; Chauhan, Pankaj; Chimni, Swapandeep Singh

    2014-05-01

    The Friedel-Crafts reaction of electron-rich phenols with isatins was developed by employing bifunctional thiourea-tertiary amine organocatalysts. Cinchona alkaloid derived thiourea epiCDT-3 a efficiently catalyzed the Friedel-Crafts-type addition of phenols to isatin derivatives to provide 3-aryl-3-hydroxy-2-oxindoles 7 and 9 in good yield (80-95 %) with good enantiomeric excess (83-94 %). Friedel-Crafts adduct 7 t was subjected to a copper(I)-catalyzed azide-alkyne cycloaddition to obtain biologically important 3-aryl-3-hydroxy-2-oxindole 11 in good enantiomeric excess and having a 1,2,3-triazole moiety. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  8. Crafting tolerance

    DEFF Research Database (Denmark)

    Kirchner, Antje; Freitag, Markus; Rapp, Carolin

    2011-01-01

    Ongoing changes in social structures, orientation, and value systems confront us with the growing necessity to address and understand transforming patterns of tolerance as well as specific aspects, such as social tolerance. Based on hierarchical analyses of the latest World Values Survey (2005–08...... results show that specific institutional qualities, which reduce status anxiety, such as inclusiveness, universality, and fairness, prevail over traditional socio-economic, societal, cultural, and democratic explanations.......–08) and national statistics for 28 countries, we assess both individual and contextual aspects that influence an individual's perception of different social groupings. Using a social tolerance index that captures personal attitudes toward these groupings, we present an institutional theory of social tolerance. Our...

  9. THE CRAFT MASTERY OF FOLK ARTISANS IN ROMANIA BEFORE AND AFTER 1989

    Directory of Open Access Journals (Sweden)

    MARIN CONSTANTIN

    2016-08-01

    Full Text Available The article deals with a series of aspects defining the “craftwork” process as a technical and artistic effort among the contemporary representatives of the peasant traditions in Romania. With respect to the craftsmanship from several Romanian ethnographic areas, three main chapters organize the present text as regards the origin of the artisans’ knowledge and skills, their craft techniques, and the folk art thus inherited, performed, and transmitted. As will be seen, “mastery” (in this case may reflect various but also interdependent phenomena like dexterity, “gift”, handwork, “the craft theft”, the management of raw materials and their properties, the imagining of an artifact and creativity in its execution, etc. Since all these facts (among others as well are difficult to encompass in a single referential term, choosing the word mastery meets at the same time exigencies of etymology (lat. magister, semantics (mastery as “skillfulness”, “ingenuity”, “ability”… and ethnography (pasărea măiastră, in Romanian “fantastic bird” as a folk artifact

  10. Editorial. Yes, Please - Both Crafts and Digital Tools in Basic Education

    Directory of Open Access Journals (Sweden)

    Liv Merete Nielsen

    2014-12-01

    Full Text Available The Ludvigsen Committee (Ludvigsen-utvalget, which aims to assess primary and secondary educational subjects in terms of the competence Norwegian society and its working life will need in the future, has published an interim report entitled Pupils’ Learning in the School of the Future – A Knowledge Foundation (Norwegian Ministry of Education and Research, 2014. The committee wrote the following about arts and crafts: “That subject will contribute to personal development and simultaneously strengthen opportunities to participate in a democratic society, which can be seen as a desire to protect both individual-oriented and community-oriented training. The breadth of the subject can restrict the ability to delve into individual topics” (NOU 2014: 7, 2014, p. 89, our translation from Norwegian. This will be an important challenge for the team in the near future. The committee shall submit their principal report by June 2015.Practical work with materials must not be removed from primary school. It should be required that qualified teachers are employed on the lower grades. Practical/hands-on work can give the trades a boost, encourage students to choose vocations and prevent dropouts in vocational education programmes. We need skilled craftsmen in the future, and good teaching in Arts & Crafts in compulsory education could provide an important basis for both future craftsmen and customers of good craftsmen.

  11. The Occurrence of Beer Spoilage Lactic Acid Bacteria in Craft Beer Production.

    Science.gov (United States)

    Garofalo, Cristiana; Osimani, Andrea; Milanović, Vesna; Taccari, Manuela; Aquilanti, Lucia; Clementi, Francesca

    2015-12-01

    Beer is one of the world's most ancient and widely consumed fermented alcoholic beverages produced with water, malted cereal grains (generally barley and wheat), hops, and yeast. Beer is considered an unfavorable substrate of growth for many microorganisms, however, there are a limited number of bacteria and yeasts, which are capable of growth and may spoil beer especially if it is not pasteurized or sterile-filtered as craft beer. The aim of this research study was to track beer spoilage lactic acid bacteria (LAB) inside a brewery and during the craft beer production process. To that end, indoor air and work surface samples, collected in the brewery under study, together with commercial active dry yeasts, exhausted yeasts, yeast pellet (obtained after mature beer centrifugation), and spoiled beers were analyzed through culture-dependent methods and PCR-DGGE in order to identify the contaminant LAB species and the source of contamination. Lactobacillus brevis was detected in a spoiled beer and in a commercial active dry yeast. Other LAB species and bacteria ascribed to Staphylococcus sp., Enterobaceriaceae, and Acetobacter sp. were found in the brewery. In conclusion, the PCR-DGGE technique coupled with the culture-dependent method was found to be a useful tool for identifying the beer spoilage bacteria and the source of contamination. The analyses carried out on raw materials, by-products, final products, and the brewery were useful for implementing a sanitization plan to be adopted in the production plant. © 2015 Institute of Food Technologists®

  12. Modeling, simulation & optimization of the landing craft air cushion fleet readiness.

    Energy Technology Data Exchange (ETDEWEB)

    Engi, Dennis

    2006-10-01

    The Landing Craft Air Cushion is a high-speed, over-the-beach, fully amphibious landing craft capable of carrying a 60-75 ton payload. The LCAC fleet can serve to transport weapons systems, equipment, cargo and personnel from ship to shore and across the beach. This transport system is an integral part of our military arsenal and, as such, its readiness is an important consideration for our national security. Further, the best way to expend financial resources that have been allocated to maintain this fleet is a critical Issue. There is a clear coupling between the measure of Fleet Readiness as defined by the customer for this project and the information that is provided by Sandia's ProOpta methodology. Further, there is a richness in the data that provides even more value to the analyst. This report provides an analytic framework for understanding the connection between Fleet Readiness and the output provided by Sandia's ProOpta software. Further, this report highlights valuable information that can also be made available using the ProOpta output and concepts from basic probability theory. Finally, enabling assumptions along with areas that warrant consideration for further study are identified.

  13. An Enquiry into Primary Student Teachers' Confidence, Feelings and Attitudes towards Teaching Arts and Crafts in Finland and Malta during Initial Teacher Training

    Science.gov (United States)

    Gatt, Isabelle; Karppinen, Seija

    2014-01-01

    Arts and crafts are connected with a variety of emotions, and the prospect of teaching these subjects could be a source of other emotions, not necessarily positive. This study explores the feelings and attitudes of student teachers towards arts and crafts prior to any training within their degree course and examines any changes that occur…

  14. Developing Craft Skills with Quasi-Cases: The Example of the Big Apple's Flirtation with Congestion Pricing

    Science.gov (United States)

    Straussman, Jeffrey D.

    2015-01-01

    This article adopts the perspective expounded by Weimer, and Vining and Weimer, that policy analysis requires "craft skills" and, therefore, one of the fundamental objectives of public affairs programs is to prepare graduates for the professional working world by providing opportunities to learn and practice these skills. Second, the…

  15. 76 FR 419 - Airworthiness Directives; 328 Support Services GmbH (Type Certificate Previously Held by AvCraft...

    Science.gov (United States)

    2011-01-05

    ... production line for the Model 328- 300 and for 328-100 aeroplanes with a s/n higher than 3098. For the... Certificate Previously Held by AvCraft Aerospace GmbH; Fairchild Dornier GmbH; Dornier Luftfahrt GmbH) Model...: Tom Rodriguez, Aerospace Engineer, International Branch, ANM-116, Transport Airplane Directorate, FAA...

  16. Erbium trifluoromethanesulfonate-catalyzed Friedel–Crafts acylation using aromatic carboxylic acids as acylating agents under monomode-microwave irradiation

    DEFF Research Database (Denmark)

    Tran, Phuong Hoang; Hansen, Poul Erik; Nguyen, Hai Truong

    2015-01-01

    Erbium trifluoromethanesulfonate is found to be a good catalyst for the Friedel–Crafts acylation of arenes containing electron-donating substituents using aromatic carboxylic acids as the acylating agents under microwave irradiation. An effective, rapid and waste-free method allows the preparation...... of a wide range of aryl ketones in good yields and in short reaction times with minimum amounts of waste...

  17. Crafting traps with attractant alcoholics an alternative for monitoring and control of borer coffee, Hypothenemus hampei (Ferrari 1867

    Directory of Open Access Journals (Sweden)

    Agramont Richard

    2010-10-01

    Full Text Available The necessity to incorporate an alternative, for monitoring and control of the borer coffee, Hypothenemus hampei (Ferrari (Choleoptera: Curculionidae to be feasible for the use of the coffee producers, in the community Choro, Coripata municipality, second section of Nor Yungas province, La Paz Bolivia. It was evaluated the capture of adult borer coffee individuals using 45 traps into 1,5 hectares distributed at random with four repetitions. It was used three types of craft traps, built with disposable plastic bottles of soft drinks, with the traps Casera, Brocap and Yessica, were evaluated three treatments: mixture of alcohols methyl (M and ethylic (E in proportions 3:1; mix 1:1 of (M and (E; mix 1:1:1 of (M (E and coffee fresh cherry liquated (CFCL and water as a witness. The largest captures of adult individuals, were present in the crafting traps with mixture of (M(E 3:1 with overalls (± standard deviation adults/traps/ten days of 3414,5±3227,7 being superior to the other treatments. The crafting trap is one of the alternatives for the control and monitoring of the borer in the coffee plantations. The use of crafting traps with alcoholic attractants for the capture of adult individuals, is present as a low cost alternative, being feasible the successful use by the producers into the management integrated programs.

  18. Racialised Entanglements of Teacher Professionalisation and Problematised Immigrant Schoolchildren: Crafting a Danish Welfare Nation-State, 1970-2013

    Science.gov (United States)

    Padovan-Özdemir, Marta

    2016-01-01

    Modern welfare states emerged as a response to the social question and were crafted through the educationalisation of society engendering a need for a variety of professionals who could take care of citizens of concern. This article revisits the social question in a post-1970 Danish context of a growing non-western immigrant and refugee population…

  19. Indium triflate in 1-isobutyl-3-methylimidazolium dihydrogenphosphate: an efficient and green catalytic system for Friedel-Crafts acylation

    DEFF Research Database (Denmark)

    Tran, Phuong Hoang; Hoang, Huy Manh; Chau, Duy-Khiem Nguyen

    2015-01-01

    Indium triflate in the ionic liquid, 1-isobutyl-3-methylimidazolium dihydrogen phosphate ([i-BMIM]H2PO4), was found to show enhanced catalytic activity in the Friedel–Crafts acylation of various aromatic compounds with acid anhydrides. The catalytic system was easily recovered and reused without ...

  20. “Not a Vacation, But a Hardening Process”: The Self-Empowerment Work of Therapeutic Craft in Nova Scotia

    Directory of Open Access Journals (Sweden)

    Erin Morton

    2014-10-01

    Full Text Available This article will examine the development of a state-sponsored therapeutic craft regime in Nova Scotia in the early to mid-twentieth century. Built on the notion that postwar residents needed "work therapy - not a vacation, but a hardening process" (Black n.d. a: 3 - therapeutic craft emerged in Nova Scotia through a complex combination of the individualization of work habits, the desire to construct an antimodern regional identity around handwork, and the notion that both infirm patients and the province as a whole could be healed from economic stagnation through craft. Key to the success of Nova Scotia's therapeutic craft regime was occupational therapist Mary E. Black's career as director of the provincial government's Handicrafts and Home Industries Division from 1943 to 1955. Black's healthcare training led her to seek out therapeutic possibilities in everyday work activities, not to mention a therapeutic solution to what she called "the atti-tude of most Nova Scotians"[:] defeatism" (Black 1949: 46. Her ability to turn seemingly disparate things - such as Scandinavian design, the ordered work of occupational rehabilitation, and a phenomenological focus on what she called “in-dividualistic existence” (Black n.d. b: 2 - into a unified therapeutic solution demonstrates that the contemporary rise of therapeutic culture under the increased individualism of the neoliberal era has an established historical root in the postwar period that remains important to understand.

  1. A Collective Case Study of Veterans inside an Arts and Crafts Room and Their Perceptions Regarding Empowerment

    Science.gov (United States)

    Hasio, Cindy Lee

    2013-01-01

    This dissertation is "A Collective Case Study of Veterans Inside an Arts and Crafts Room and Their Perceptions Regarding Empowerment." This research examined to what degree art making, and in what ways a community of learning contributed to veterans' self-worth and empowerment through their creative activities and interactions inside an…

  2. The Use of Shock Isolation mounts in Small High-Speed Craft to Protect Equipment from Wave Slam Effects

    Science.gov (United States)

    2017-07-01

    including suggestions for reducing this burden to Department of Defense, Washington Headquarters Services , Directorate for Information Operations and... failure during high-speed operations in rough seas is discussed. 15. SUBJECT TERMS Shock mounts planing craft equipment data...shock isolation systems. An alternative method for minimizing the risk of equipment failure during high-speed operations in rough seas is discussed

  3. Efficient Friedel-Crafts benzoylation of aniline derivatives with 4-fluorobenzoyl chloride using copper triflate in the synthesis of aminobenzophenones

    DEFF Research Database (Denmark)

    Tran, Phuong Hoang; Phung, Huy Quang; Hansen, Poul Erik

    2016-01-01

    An efficient pathway for the synthesis of the aminobenzophenone derivatives via Friedel–Crafts benzoylation using copper triflate as catalyst is proposed. New derivatives are synthesized. The copper triflate could be easily recovered and reused without loss of catalytic activity. Both the use of ...... of ionic liquids and microwave heating turned out to be fruitful....

  4. Can job crafting reduce job boredom and increase work engagement? A three-year cross-lagged panel study

    NARCIS (Netherlands)

    Harju, Lotta K.; Hakanen, Jari J.; Schaufeli, Wilmar B.

    2016-01-01

    Building upon the Conservation of Resources (COR) theory, this longitudinal study examined whether job crafting behaviors (i.e. increasing structural and social job resources and increasing challenges) predict less job boredom and more work engagement. We also tested the reverse causation effects of

  5. Uncovering Procedural Knowledge in Craft, Design, and Technology Education: A Case of Hands-On Activities in Electronics

    Science.gov (United States)

    Pirttimaa, Matti; Husu, Jukka; Metsärinne, Mika

    2017-01-01

    Different knowledge types have their own specific features and tasks in the learning process. Procedural knowledge is used in craft and technology education when students solve problems individually and share their working knowledge with others. This study presents a detailed analysis of a one student's learning process in technology education and…

  6. Efficient Friedel-Crafts benzoylation of aniline derivatives with 4-fluorobenzoyl chloride using copper triflate in the synthesis of aminobenzophenones

    DEFF Research Database (Denmark)

    Tran, Phuong Hoang; Phung, Huy Quang; Hansen, Poul Erik

    2016-01-01

    An efficient pathway for the synthesis of the aminobenzophenone derivatives via Friedel–Crafts benzoylation using copper triflate as catalyst is proposed. New derivatives are synthesized. The copper triflate could be easily recovered and reused without loss of catalytic activity. Both the use of ...

  7. Job Crafting and Identity in Low-Grade Work: How Hospital Porters Redefine the Value of Their Work and Expertise

    Science.gov (United States)

    Fuller, Alison; Unwin, Lorna

    2017-01-01

    Over 25 years ago, Brown and Duguid ("Organisation Science," 2(1), 40-57, 1991) highlighted the differences between the way organisations formally describe and delineate jobs and the actual practices of their employees. This paper combines ideas from their seminal contribution with theories of "job crafting" and identity to…

  8. Modeling Ships and Space Craft The Science and Art of Mastering the Oceans and Sky

    CERN Document Server

    Hagler, Gina

    2013-01-01

    Modeling Ships and Space Craft: The Science and Art of Mastering the Oceans and Sky begins with the theories of Aristotle and Archimedes, moving on to examine the work of Froude and Taylor, the early aviators and the Wright Brothers, Goddard and the other rocket men, and the computational fluid dynamic models of our time. It examines the ways each used fluid dynamic principles in the design of their vessels. In the process, this book covers the history of hydrodynamic (aero and fluid) theory and its progression – with some very accessible science examples – including seminal theories. Hydrodynamic principles in action are also explored with examples from nature and the works of man. This is a book for anyone interested in the history of technology – specifically the methods and science behind the use of scale models and hydrodynamic principles in the marine and aeronautical designs of today.

  9. Cosmogonic Perceptions in the Armenian Traditional Musical Instrument-crafting Culture

    Science.gov (United States)

    Pikichian, Hripsime

    2015-07-01

    Based on research data and materials recorded by folk musicians and craftsmen, the article presents the musical instrument-crafting in traditional culture, its contribution in to re-establishment of cosmic order. In this context, the several issues are reviewed in detail: individuality of craftsmen and musicians, the raw materials for the creation of instrument, the instrument structure, the manufacturing process, the ornaments and application. According to the traditional view, using the elements of nature and imitating the sounds of nature and human psychological states the master imitates God repeating the process of creation of the Universe. So, the Instrument is held capable to influence the society contributing to the eternity of life.

  10. "Slow food" post-qualitative research in psychology: old craft skills in new disguise?

    Science.gov (United States)

    Demuth, Carolin

    2015-06-01

    The present paper addresses several aspects discussed in the special issue on the future of qualitative research in psychology. Particularly, it asks whether in light of the overhomogenization of the term "qualitative methods" researchers actually can still assume that they talk about the same thing when using this terminology. In addressing the topic of what constitutes the object of psychological research and what accordingly could be a genuinely psychological qualitative research it acknowledges the need to return to the study of persons' unique experience. In light of the risk of "McDonaldization" in present qualitative research, it argues that we need to return to learning research methods as craft skills. It will then give an outlook on how recent developments in discursive and narrative psychology offer a fruitful avenue for studying unique psychological experience as people manage to 'move on' in a material world and in irreversible time.

  11. Energy spectrum of iron nuclei measured inside the MIR space craft using CR-39 track detectors

    CERN Document Server

    Guenther, W; Becker, E; Flesch, F; Heinrich, W; Huentrup, G; Reitz, G; Roecher, H; Streibel, T

    1999-01-01

    We have exposed stacks of CR-39 plastic nuclear track detectors inside the MIR space craft during the EUROMIR95 space mission for almost 6 months. Over this long period a large number of tracks of high LET events was accumulated in the detector foils. The etching and measuring conditions for this experiment were optimized to detect tracks of stopping iron nuclei. We found 185 stopping iron nuclei inside the stack and identified their trajectories through the material of the experiment. Based on the energy-range relation the energy at the surface of the stack was determined. These particles allow the determination of the low energy part of the spectrum of iron nuclei behind shielding material inside the MIR station.

  12. Socio-economic Classification and its Scope in Crafting Rural Segments

    Directory of Open Access Journals (Sweden)

    Rinalini Pathak Kakati

    2015-12-01

    Full Text Available With the liberalization of the Indian Economy in the mid 1990’s, substantial growth has been seen in the rural areas. Rural India which comprises around 70% of the total population of the country has become an emerging area for marketers. This study tries to identify key market variables that can help in crafting rural market segments. The socio-economic classification (SEC 2011 which segments the market based on education level and possession of consumer durables. This study examines income as another key market variable together with education in the creation of distinct segments or hybrid segments. It then further identifies important criteria like technical, promotional and social in influencing consumers’ behaviour in the context of the purchase of consumer durables which can thereby help to create segments. The study concludes that the increase in education level has higher impact than increase in income on the important identified purchase criteria.

  13. Crafting interactivity for stakeholder engagement: transforming assumptions about communication in science and policy.

    Science.gov (United States)

    Aakhus, Mark

    2011-11-01

    The International Radiation Protection Association's guiding principles for stakeholder engagement focus on fostering, facilitating, and enabling interaction among stakeholders that is inclusive and fosters competent decision making. Implicit in these standards is a call to cultivate knowledge and competence in designing communication for stakeholder engagement among radiation protection professionals. Communication as design is an approach to risk communication in science and policy that differs from, yet complements, the more well-known communication practices of informing and persuading. Design focuses on the recurring practical problem faced by professionals in making communication possible among stakeholders where it has otherwise been difficult, impossible, or even unimagined. The knowledge and competence associated with design involves principles for crafting interactivity across a variety of mediated and non-mediated encounters among stakeholders. Risk communication can be improved by cultivating expertise in scalable communication design that embraces the demands of involvement without abandoning the need for competence in science and policy communication.

  14. 3D printing as a Ceramic Craft Tool in Its Own Right

    DEFF Research Database (Denmark)

    Hansen, Flemming Tvede; Falin, Priska

    2016-01-01

    In April 2016, four universities met for one week at the KAHLA Porcelain Factory to discuss the future of ceramics and, through workshops, explore the theme »shaping the future«. One of the workshops was focusing on 3D printing in clay and the concept of material driven 3D printing in clay....... This article reports from and reflects on the experiments and discussions in this workshop and concentrates on 3D printing in clay from the perspective of studio practice in art and design. The main point of interest is in examining how a technology such as 3D printing can be utilised and seen as a new ceramic...... craft tool in its own right and how 3D printed ceramics can also be considered as handmade objects....

  15. Archaeometry and craft context of the gold disks from Fortios (Portalegre, Alto Alentejo, Portugal

    Directory of Open Access Journals (Sweden)

    Alicia Perea

    2017-01-01

    Full Text Available Starting from the topographic study and the elemental analysis of four gold objects from Fortios, we define a little-known type of gold object and survey all examples known to date. It is important to select the appropriate analytical technique depending on the problem to be solved and in order to obtain reliable results. In our particular case this allowed us to detect a brazing procedure using a solder of a lower melting point than the parts to be joined. Comparing analytical data from other, similar objects permitted the reconstruction of their technological domain, which is clearly Mediterranean. Finally the archaeological context, between the 8th and 7th centuries BC, and the particular character of the workshop point to a craft production belonging to the Orientalizing period of Southwestern Iberia.

  16. The staging of a hospice arts and crafts exhibition in the UK.

    Science.gov (United States)

    Sarginson, Andrea

    2005-09-01

    The use of arts in hospices is now well established. However, the voluntary nature of much hospice work in England encourages most regular creative activities to be provided by volunteers with minimal financial support. This article looks at how a successful arts and crafts exhibition for a hospice community was staged by a volunteer arts worker, helped by art and design students from the local university. It was not intended that the exhibition should be a research project; however, it became clear that to learn more about arts practice within a hospice environment, it would need to be appraised in some way. The project leader (and author) adopted an approach which reflected on the responses of people involved in the preparation and staging of the exhibition.

  17. Crafting minds and communities with Minecraft [version 2; referees: 2 approved

    Directory of Open Access Journals (Sweden)

    Benjamin C. Riordan

    2017-01-01

    Full Text Available Minecraft is a first-person perspective video game in which players roam freely in a large three-dimensional environment. Players mine the landscape for minerals and use these minerals to create structures (e.g., houses and mould the landscape. But can Minecraft be used to craft communities and minds? In this opinion piece, we highlight the enormous potential of Minecraft for fostering social connectedness, collaboration, and its potential as an educational tool. We highlight the recent use of Minecraft to aid socialization in individuals with Autistic Spectrum Disorder (ASD and promote civic engagement via the United Nations Human Settlement Program. We further provide novel links between Minecraft and recent on work on the role of social cures and community empowerment in enhancing mental health, wellbeing, and resilience.

  18. Liquid Chromatography-Mass Spectrometry Analysis Reveals Hydrolyzed Gluten in Beers Crafted To Remove Gluten.

    Science.gov (United States)

    Colgrave, Michelle L; Byrne, Keren; Howitt, Crispin A

    2017-11-08

    During brewing, gluten proteins may be solubilized, modified, complexed, hydrolyzed, and/or precipitate. Gluten fragments that persist in conventional beers render them unsuitable for people with celiac disease (CD) or gluten intolerance. Barley-based beers crafted to remove gluten using proprietary precipitation and/or application of enzymes, e.g. prolyl endopeptidases (PEP) that degrade the proline-rich gluten molecules, are available commercially. Gluten measurement in fermented products remains controversial. The industry standard, a competitive ELISA, may indicate gluten values gluten peptides derived from hydrolyzed fragments, many >30 kDa in size. Barley gluten (hordeins) were detected in all beers analyzed with peptides representing all hordein classes detected in conventional beers but also, alarmingly, in many gluten-reduced beers. It is evident that PEP digestion was incomplete in several commercial beers, and peptides comprising missed cleavages were identified, warranting further optimization of PEP application in an industrial setting.

  19. How Valuable is a Well-Crafted Design and Name Brand?

    DEFF Research Database (Denmark)

    Kristensen, Tore; Gabrielsen, Gorm; Zaichkowsky, Judith

    2012-01-01

    Preferences for similarly designed consumer products, evaluated blind and branded and also with and without prices, were tested in a consumer setting. The consumer's perceptual experience led to preference of the well-crafted high-priced option. This preference was enhanced by priming consumers...... with background information about the brand, perhaps causing the subjects to guess which choice was the well-known brand before evaluation. Preferences for that choice increased again when brand names were visible during evaluation. When actual prices were added to the evaluations, preferences for the well......-known brand were very robust to high prices, indicating the strength of the brand name. Using the least preferred option and the lowest price as an anchor, the consumers' price threshold to pay for the preferred design and the brand name was computed. Attempts to explain and predict individual differences...

  20. Free Software Beyond Radical Politics: Negotiations of Creative and Craft Autonomy in Digital Visual Media Production

    Directory of Open Access Journals (Sweden)

    Julia Velkova

    2016-08-01

    Full Text Available Free software development and the technological practices of hackers have been broadly recognised as fundamental for the formation of political cultures that foster democracy in the digital mediascape. This article explores the role of free software in the practices of digital artists, animators and technicians who work in various roles for the contemporary digital visual media industries. Rather than discussing it as a model of organising work, the study conceives free software as a production tool and shows how it becomes a locus of politics about finding material security in flexible capitalism. This politics is ultimately contradictory in that it extends creative and craft autonomy of digital artists but does not mobilise a critical project. Instead, it nurtures further precarious labour. Empirically, the article draws on ethnographically collected material from the media practices of digital artists and programmers who engage with two popular free software production tools, Blender and Synfig.

  1. Death from atlanto-occipital dislocation in a boy due to personal water craft collision.

    Science.gov (United States)

    Carson, Henry J; Martin Johnson, J

    2002-12-01

    Injuries associated with use of personal water craft (PWC) typically include fractures, lacerations, or head injuries. Deaths are rare. We recently encountered an unusual case of a collision between two PWCs in which a 9-year-old boy was struck on the left side, causing the vehicle to rock and him to twist upward and to the right. There was rapid extension, flexion, and rotation of his head. At postmortem examination, it was established that the boy died from atlanto-occipital dislocation and brainstem transection. The risk of atlanto-occipital dislocation is high in children under 10. The tectoral ligament which stabilizes the upper cervical spine can be torn or ruptured by hyperextension-flexion injury. Some atlanto-occipital dislocations in children can be stabilized and recovery is possible, but in this case of complete ligament rupture and brainstem transection, death was immediate.

  2. The craft of scientific presentations critical steps to succeed and critical errors to avoid

    CERN Document Server

    Alley, Michael

    2013-01-01

    The Craft of Scientific Presentations, 2nd edition aims to strengthen you as a presenter of science and engineering. The book does so by identifying what makes excellent presenters such as Brian Cox, Jane Goodall, Richard Feynman, and Jill Bolte Taylor so strong. In addition, the book explains what causes so many scientific presentations to flounder. One of the most valuable contributions of this text is that it teaches the assertion-evidence approach to scientific presentations. Instead of building presentations, as most engineers and scientists do, on the weak foundation of topic phrases and bulleted lists, this assertion-evidence approach calls for building presentations on succinct message assertions supported by visual evidence. Unlike the commonly followed topic-subtopic approach that PowerPoint leads presenters to use, the assertion-evidence approach is solidly grounded in research. By showing the differences between strong and weak presentations, by identifying the errors that scientific presenters ty...

  3. Socio-Economic Benefits of Bamboo-Craft Entrepreneurship: The Case of Rinconada Bamboo Entrepreneurs

    Directory of Open Access Journals (Sweden)

    Seth B. Barandon

    2015-12-01

    Full Text Available –Bamboo entrepreneurship is one of the key instruments in uplifting the socio-economic status of the poor and under privileged people in Rinconada area. This study evaluated the socioeconomic benefits of bamboo craft making on the entrepreneurs of the district. Using descriptive-survey, data were obtained from 60 purposely chosen bamboo entrepreneurs from a list given by the Department of Trade of Industry. A 12-item researcher-made questionnaire was the main gathering tool supported by interview and observation. Results revealed that the social benefits derived by the bamboo entrepreneurs can able to communicate to more networks, adequate support to education of children is being provided, and television sets, while economic benefits is having their own house with sanitation. The bamboo entrepreneurs can satisfy the hierarchy of needs for shelter, security and social communication.

  4. Structure Prediction for Gland Segmentation with Hand-Crafted and Deep Convolutional Features.

    Science.gov (United States)

    Manivannan, Siyamalan; Li, Wenqi; Zhang, Jianguo; Trucco, Emanuele; McKenna, Stephen

    2017-09-08

    We present a novel method to segment instances of glandular structures from colon histopathology images. We use a structure learning approach which represents local spatial configurations of class labels, capturing structural information normally ignored by sliding-window methods. This allows us to reveal different spatial structures of pixel labels (e.g., locations between adjacent glands, or far from glands), and to identify correctly neighbouring glandular structures as separate instances. Exemplars of label structures are obtained via clustering and used to train support vector machine classifiers. The label structures predicted are then combined and post-processed to obtain segmentation maps. We combine hand-crafted, multi-scale image features with features computed by a deep convolutional network trained to map images to segmentation maps. We evaluate the proposed method on the public domain GlaS dataset, which allows extensive comparisons with recent, alternative methods. Using the GlaS contest protocol, our method achieves the overall best performance.

  5. Data-fusion for multiplatform characterization of an Italian craft beer aimed at its authentication.

    Science.gov (United States)

    Biancolillo, Alessandra; Bucci, Remo; Magrì, Antonio L; Magrì, Andrea D; Marini, Federico

    2014-04-11

    Five different instrumental techniques: thermogravimetry, mid-infrared, near-infrared, ultra-violet and visible spectroscopies, have been used to characterize a high quality beer (Reale) from an Italian craft brewery (Birra del Borgo) and to differentiate it from other competing and lower quality products. Chemometric classification models were built on the separate blocks using soft independent modeling of class analogies (SIMCA) and partial least squares-discriminant analysis (PLS-DA) obtaining good predictive ability on an external test set (75% or higher depending on the technique). The use of data fusion strategies - in particular, the mid-level one - to integrate the data from the different platforms allowed the correct classification of all the training and validation samples. Copyright © 2014 Elsevier B.V. All rights reserved.

  6. Data-fusion for multiplatform characterization of an italian craft beer aimed at its authentication

    Energy Technology Data Exchange (ETDEWEB)

    Biancolillo, Alessandra; Bucci, Remo; Magrì, Antonio L.; Magrì, Andrea D.; Marini, Federico, E-mail: fmmonet@hotmail.com

    2014-04-01

    Highlights: • Characterization of beer samples by five different fingerprinting techniques. • Chemometric discriminant and class-modeling techniques used for their authentication. • Mid-level data fusion allowed correct classification of all samples. - Abstract: Five different instrumental techniques: thermogravimetry, mid-infrared, near-infrared, ultra-violet and visible spectroscopies, have been used to characterize a high quality beer (Reale) from an Italian craft brewery (Birra del Borgo) and to differentiate it from other competing and lower quality products. Chemometric classification models were built on the separate blocks using soft independent modeling of class analogies (SIMCA) and partial least squares-discriminant analysis (PLS-DA) obtaining good predictive ability on an external test set (75% or higher depending on the technique). The use of data fusion strategies – in particular, the mid-level one – to integrate the data from the different platforms allowed the correct classification of all the training and validation samples.

  7. Development and Positioning of the Collective Product of Slovenian Craft Trademark

    Directory of Open Access Journals (Sweden)

    Adrijana Poljanšek

    2017-09-01

    Full Text Available The new collective trademark Izdelek slovenske obrti (hereinafter: PSC; English: Product of Slovenian Craft was launched on the market in 2014. The initiative for the trademark was provided by the Textile Section at the Chamber of Craft and Small Business of Slovenia (hereinafter: the OZS, which also registered the trademark. Members of the OZS have the right to obtain and use the trademark, and to use it to promote their products or services. After two years, only a small number of section members use the trademark. Because the section would like to see an increased number of members use the trademark, research regarding the latter was carried out. The results are presented in this article. The descriptive course of development and registration of the collective trademark PSC is presented in the first part of our research. In the second part, questionnaires were drafted for collective trademark PSC users, potential users and consumers. The results obtained using three questionnaires were analysed using a SWOT analysis. Based on the results, it was determined that the trademark has not yet been properly positioned on the Slovenian market. Advantages include the familiarity of Textile Section members with the trademark, and their eagerness to use it. One disadvantage is the trademark’s current lack of recognition among consumers. For this reason, section members who are also potential users of the trademark do not give it priority and therefore do not opt to use it. The following will impact the trademark’s recognition among consumers: innovative marketing campaigns, the inclusion of the media and social networks, the improved recognition and visibility of the logotype, and an effective and pervasive slogan, as was determined in our research.

  8. PEDAGOGICAL SUPPORT OF GIFTED STUDENTS FROM CARPATHIAN MOUNTAIN AREAS BY MEANS OF FOLK ART CRAFTS

    Directory of Open Access Journals (Sweden)

    Iryna Kozlovska

    2015-04-01

    Full Text Available This paper, presented at the Conference Plenary the possibilities of pedagogical support of gifted students from vocational schools, living in the mountainous areas of the Carpathians. Education of talented and gifted students requires pedagogical support. The specific conditions, in which Carpathian students live, require the development of pedagogical support of their abilities. New approaches to teaching science, which led to the selection of topics of this article are described. Gifted personalities differ from their peers by same criterias. The social aspect of the problem remains in the shadow: not to be ashamed of your talent and not to compare it with cliches. And goals of educators and psychologists have to be slightly different as is common. Widespread  Carpathian crafts include: embroidery, artistic textiles producing, carpet manufacture, carving, pottery, metalworking, fabric painting, knitting, lace, artistic weaving, artistic working of  leather, stones, bones and horns. Nowadays, some detachment of mountainous regions has significantly reduced due to new means of communication, including the Internet. The possibilities of colleges in mountainous regions still cannot reach the level of the colleges in capital. In Carpathian and Prykrpattya regions there is a number of vocational schools of art direction. During the execution of creative work in class industrial training necessary for students to comply with the rules of relationships form and decoration in various ways: decorative motif obeys the functional form, enriching it artistic and creative solutions, utilitarian function obeys the decorative motif Products, the form of the product can be extremely decorative, artistic and creative product solutions focused on practical value and decorative value of the product. Pedagogical support of gifted students from art colleges in the Carpathian region has extremely wide range of opportunities. The problem of finding and nurturing

  9. Multinationals and plant survival

    DEFF Research Database (Denmark)

    Bandick, Roger

    2010-01-01

    The aim of this paper is twofold: first, to investigate how different ownership structures affect plant survival, and second, to analyze how the presence of foreign multinational enterprises (MNEs) affects domestic plants’ survival. Using a unique and detailed data set on the Swedish manufacturing...... sector, I am able to separate plants into those owned by foreign MNEs, domestic MNEs, exporting non-MNEs, and purely domestic firms. In line with previous findings, the result, when conditioned on other factors affecting survival, shows that foreign MNE plants have lower survival rates than non......-MNE plants. However, separating the non-MNEs into exporters and non-exporters, the result shows that foreign MNE plants have higher survival rates than non-exporting non-MNEs, while the survival rates of foreign MNE plants and exporting non-MNE plants do not seem to differ. Moreover, the simple non...

  10. Robotic craft: Rapid-prototype technology may take the labor out of craft, but it also allows individually styled items to compete with those that have been mass-produced

    OpenAIRE

    Miodownik, M.

    2006-01-01

    Computer-controlled manufacturing machines are no longer confined in the large companies, but they are also being increasingly bought and used in small small businesses and craftspeople. Customers can order any design that they in the shop, which is then tailored digitally to their exact needs. Another important aspect of this machines is that they are affordable, so that jewelers, designers, and craft cooperatives can compete on price and precision with big business. The technology is revolu...

  11. Concerning the Charging of an Exploration Craft on and near a Small Asteroid

    Science.gov (United States)

    Jackson, T. L.; Zimmerman, M. I.; Farrell, W. M.

    2014-01-01

    Introduction: An object immersed in an airless plasma environment will experience a natural process of surface charging in order to acheieve current balance, or zero net electric current to the object. It has been shown in recent computer simulations that the small-body plasma environment is very complex [1], considering effects of photoemission, topography, and formation of a plasma wake. For this work we consider an exploration craft (or astronaut) immersed within a plasma environment near an asteroid, which exhibits widely varying solar wind and photoelectric particle fluxes and continuously evolving illumination conditions. Objective: We aim to determine how an explo-ration craft or astronaut suit accumulates charge while located in the "nightside" asteroid wake where the particle fluxes are reduced, and in the dayside near-surface photoelectron sheath, by combining an object charging model [2] with kinetic simulations of a near-asteroid plasma environment [1]. We consider an astronaut floating near the asteroid while not in contact with the surface, as well as an astronaut moving along the surface using their hands/gloves to crawl along. Results: The modeling results suggest that remediation of triboelectric charge via accumulation of plasma currents is an important factor to consider when designing future NEA mission infrastructure, especially if repeated and frequent contact with the surface is planned. In shadowed regions such as the location shown in Fig. 1a, the plasma currents are so low (and the effective charge-remediation timescale so long, e.g. minutes to hours) that repeated contact with the surface tribocharges the glove in an uncontrollable fashion, as shown for two representative electron temperatures in Fig. 2a. The resulting buildup of significant negative charge would eventually initiate some other "current of last resort" [4] such as transport of positively-charged dust, field-emission from the glove, or significant alteration of

  12. Uncovering patterns of consumers' interest for beer: A case study with craft beers.

    Science.gov (United States)

    Donadini, Gianluca; Porretta, Sebastiano

    2017-01-01

    To uncover patterns of consumer interest in craft beers, the authors explored the quality perception of craft beers in a panel of industrial mass-marketed beer drinkers (n=150) and examined the differences in interest for this beer segment between men and women. The authors adopted a conjoint rating experiment in which the respondents were given forty-nine beer profiles to evaluate and were asked to score the degree of interest in each profile on a 9-point scale. Each profile was described on eight attributes (type of brewery, brewing technology, characterizing raw materials, brewhouse equipment, location of the brewery, type of container, retail price, where to buy) varied at different levels. Results showed that Italian consumers placed greatest importance on type of container (30.49%) and on brewing technology (17.64%). Characterizing raw materials (13.44%) and type of brewery (12.64) rank 3 and 4 and were placed in the same band some way below brewing technology. Retail price (9.87%) and where to buy (8.73%) were of far less importance. The least importance of all was attached to brewhouse equipment (4.44%) and to location of the brewery (2.75%). As far as utility values are concerned, the factor level glass bottle+crown cap and the factor level microfiltration are the utilities that most increased the interest of consumers. They were followed by the factor level local grains, stainless steel keg and monastery. In contrast, the factor level PET Keg, aluminum can and large scale corporate brewery showed the greatest negative impact on interest. Men and women shared similar patterns of interest. However, men placed more importance than women on retail price, location of the brewery and where to buy. Women attached more importance than men on type of container, brewing technology and type of brewer. These findings are relevant to understanding consumers'behavior in the beer market and to translating consumer needs, wants and expectations into manufacturing

  13. The effects of a combined physical activity, recreation, and art and craft program on ADL, cognition, and depression in the elderly

    OpenAIRE

    Kim, DeokJu

    2017-01-01

    [Purpose] To determine the effects of a combined physical activity, arts and crafts, and recreational program on the activities of daily living (ADL), cognitive function, and depression in the elderly. [Subjects and Methods] Twenty-eight elderly persons aged 65?years or older who live in P City, South Korea participated in a program combining arts and crafts and physical and recreational activities, twice weekly for eight weeks (a total of 16 sessions). The subjects? ADL, cognitive function, ...

  14. Polystyrene-supported cu(II)-R-Box as recyclable catalyst in asymmetric Friedel–Crafts reaction

    KAUST Repository

    Desyatkin, V. G.

    2017-02-12

    The complex of copper(II) trifluoromethanesulfonate with chiral isopropyl bis(oxazoline) ligand (i-Pr-Box) was immobilized on accessible and inexpensive Merrifield resin according to a “click” procedure. The resulting catalyst showed high efficiency and recyclability in the asymmetric Friedel–Crafts alkylation of indole and its derivatives. The catalyst can be recycled five times without appreciable loss in activity and enantioselectivity.

  15. THE ROLE OF FOLK ARTS AND CRAFTS OF DAGESTAN IN CONSOLIDATING AND EXPANDING THE TOURIST-EXCURSION ROUTES

    Directory of Open Access Journals (Sweden)

    G. G. Gazimagomedov

    2017-01-01

    Full Text Available Aim. The aim of this study is to create and represent the tourist routes in the places of the traditional folk arts and crafts in the Republic of Dagestan.Research Methodology. In the first stage of the study, according to the register and public materials we identified and studied traditional places of folk arts and crafts; carried out monitoring of existing tourist routes and programs. Developed routes are included in the tourist route map.Findings and discussion. We developed five radial exit routes from the city of Makhachkala, characteristics of which are presented below. Folk arts and crafts of Dagestan are a unique part of the artistic culture and at the same time, it is a branch of industry with a high level of tourist attractiveness. Today, Dagestan is one of the few areas in the modern world where traditional folk art is naturally a part of a contemporary social life having the rights of the dominant cultural unity due to the peculiarities of its historical development. Archaeological studies show that due to the geographical position, in Dagestan, there has been an interaction of significant aspects of cultural phenomena relating to the ancient civilizations of the Mediterranean, Western, Central and Eastern Europe, on the one hand, and the development of cultures of different regions of Asia, on the other hand. Coupled with the traditions of the ancient population of the Caucasus, they formed complex and varied artistic conglomerate.Conclusion. The study revealed the basic centers of traditional arts and crafts of the Republic of Dagestan, hiving a high tourism potential. On this basis, we developed five tourist-excursion routes. These routes are included in the information booklet, which has a marketing and information value. 

  16. An efficient and green synthesis of 1-indanone and 1-tetralone via intramolecular Friedel-Crafts acylation reaction

    DEFF Research Database (Denmark)

    Tran, Phuong Hoang; Huynh, Vy Hieu; Hansen, Poul Erik

    2015-01-01

    Metal-triflate-catalyzed intramolecular Friedel–Crafts acylation of 3-arylpropanoic and 4-arylbutanoic acids in triflate-anion ionic liquids under monomodal microwave irradiation is reported. The environmentally benign synthetic procedure allows the formation of cyclic ketones in good yields within...... a short reaction time. The catalytic metal triflate in triflate-anion ionic liquids can be easily recovered and reused several times without significant loss of the catalytic performance....

  17. Modificación de Betún-Venezuela por reacción de Friedel y Crafts

    OpenAIRE

    Blanco, Manuel; Cuevas, Ángel; Ortega, Juan J.

    1987-01-01

    In this work, a Venezuelan-bitumen of newtonian nature was modified by Friedel and Crafts reaction, changing it in new materials that present pseudoplastic characteristics, with very different properties from the original product. These new materials are harder and have less thermical susceptibility and allow us to use them in many applications such as paving and roofing. The modifications have been made with rubbers, PVC, phtalic anhydride, maleic anhydride, 1, 2-propyleneglycol, hexamethyle...

  18. Combat Support Forces (1C6C) Naval Surface Forces Requirements-based Budget Determination for Assault Craft Unit ONE

    Science.gov (United States)

    2009-06-01

    Kristy, Riley and Sydney. Mike Ruminski would like to thank his mother, Norma Ruminski, who passed away prior to completion of the project. We...Upon completion of the briefing the authors sat down with each subordinate command leadership team individually to ask more detailed questions and...tour their facilities and see much of the equipment and craft that they used. After receiving the general overview, the authors sat down with the

  19. Heteropoly acid encapsulated into zeolite imidazolate framework (ZIF-67) cage as an efficient heterogeneous catalyst for Friedel–Crafts acylation

    Energy Technology Data Exchange (ETDEWEB)

    Ammar, Muhammad; Jiang, Sai; Ji, Shengfu, E-mail: jisf@mail.buct.edu.cn

    2016-01-15

    A new strategy has been developed for the encapsulation of the phosphotungstic heteropoly acid (H{sub 3}PW{sub 12}O{sub 40} denoted as PTA) into zeolite imidazolate framework (ZIF-67) cage and the PTA@ZIF-67(ec) catalysts with different PTA content were prepared. The structure of the catalysts was characterized by XRD, BET, SEM, FT-IR, ICP-AES and TG. The catalytic activity and recovery properties of the catalysts for the Friedel-Crafts acylation of anisole with benzoyl chloride were evaluated. The results showed that 14.6–31.7 wt% PTA were encapsulated in the ZIF-67 cage. The PTA@ZIF-67(ec) catalysts had good catalytic activity for Friedel-Crafts acylation. The conversion of anisole can reach ~100% and the selectivity of the production can reach ~94% over 26.5 wt% PTA@ZIF-67(ec) catalyst under the reaction condition of 120 °C and 6 h. After reaction, the catalyst can be easily separated from the reaction mixture by the centrifugation. The recovered catalyst can be reused five times and the selectivity can be kept over 90%. - Graphical abstract: The PTA@ZIF-67 catalysts with different PTA content were prepared by encapsulating the PTA into ZIF-67 cage and the as-synthesized catalysts exhibited good catalytic activity for the Friedel–Craft acylation of anisole with benzoyl chloride.

  20. Crafting Linked Open Data for Cultural Heritage: Mapping and Curation Tools for the Linked Jazz Project

    Directory of Open Access Journals (Sweden)

    M. Cristina Pattuelli

    2013-07-01

    Full Text Available This paper describes tools and methods developed as part of Linked Jazz, a project that uses Linked Open Data (LOD to reveal personal and professional relationships among jazz musicians based on interviews from jazz archives. The overarching aim of Linked Jazz is to explore the possibilities offered by LOD to enhance the visibility of cultural heritage materials and enrich the semantics that describe them. While the full Linked Jazz dataset is still under development, this paper presents two applications that have laid the foundation for the creation of this dataset: the Mapping and Curator Tool, and the Transcript Analyzer. These applications have served primarily for data preparation, analysis, and curation and are representative of the types of tools and methods needed to craft linked data from digital content available on the web. This paper discusses these two domain-agnostic tools developed to create LOD from digital textual documents and offers insight into the process behind the creation of LOD in general.

  1. Concepts of illicit drug quality among darknet market users: Purity, embodied experience, craft and chemical knowledge.

    Science.gov (United States)

    Bancroft, Angus; Scott Reid, Peter

    2016-09-01

    Users of darknet markets refer to product quality as one of the motivations for buying drugs there, and vendors present quality as a selling point. However, what users understand by quality and how they evaluate it is not clear. This article investigates how users established and compared drug quality. We used a two-stage method for investigating users' assessments. The user forum of a darknet market that we called 'Merkat' was analysed to develop emergent themes. Qualitative interviews with darknet users were conducted, then forum data was analysed again. To enhance the applicability of the findings, the forum was sampled for users who presented as dependent as well as recreational. Quality could mean reliability, purity, potency, and predictability of effect. We focused on the different kinds of knowledge users drew on to assess quality. These were: embodied; craft; and chemical. Users' evaluations of quality depended on their experience, the purpose of use, and its context. Market forums are a case of indigenous harm reduction where users share advise and experiences and can be usefully engaged with on these terms. Copyright © 2015 Elsevier B.V. All rights reserved.

  2. How to surf today's information tsunami: on the craft of effective reading.

    Science.gov (United States)

    Erren, Thomas C; Cullen, Paul; Erren, Michael

    2009-09-01

    In this editorial, we provide concise suggestions to help individuals decide what scientific papers to read and how to read them. We do so because--like others--we are frequently asked by people with interest in science as to how to effectively surf today's information tsunami. This is particularly important in, but not confined to, universities and other research institutions where reading scientific papers is a fundamental task that forms the basis for all other academic activities such as writing papers or grant applications, providing reviews for a journal, preparing for postdoctoral positions, qualifying for collaborations or making oral or poster presentations. Included in our Advices 1-8 are concise suggestions which range from the appropriate motivation for reading articles in books, journals or on the internet to the very craft of systematically reviewing and, indeed, constantly challenging what one reads. We close this editorial with reading Advice 9 "You should always identify the roots of thinking and research" and 10 "The Golden Rule: set aside reading time" which should be necessary conditions for everyone who works in science. Importantly, while maintaining focus on material immediately pertinent to one's primary research area, one should read about developments in other fields as well because this may be the key to original, and sometimes revolutionary, research.

  3. From Dalek half balls to Daft Punk helmets: Mimetic fandom and the crafting of replicas

    Directory of Open Access Journals (Sweden)

    Matt Hills

    2014-06-01

    Full Text Available Mimetic fandom is a surprisingly understudied mode of (culturally masculinized fan activity in which fans research and craft replica props. Mimetic fandom can be considered as (inauthentic and (immaterial, combining noncommercial status with grassroots marketing or brand reinforcement as well as fusing an emphasis on material artifacts with Web 2.0 collective intelligence. Simply analyzing mimetic fandom as part of fannish material culture fails to adequately assess the nonmaterial aspects of this collaborative creativity. Two fan cultures are taken as case studies: Dalek building groups and Daft Punk helmet constructors. These diverse cases indicate that mimetic fandom has a presence and significance that moves across media fandoms and is not restricted to the science fiction, fantasy, and horror followings with which it is most often associated. Mimetic fandom may be theorized as an oscillatory activity that confuses binaries and constructions of (academic/fan authenticity. This fan practice desires and pursues a kind of ontological bridging or unity—from text to reality—that is either absent or less dominant in many other fan activities such as cosplay, screen-used prop collecting, and geographical pilgrimage. Fan studies may benefit from reassessing the place of mimesis, especially in order to theorize fan practices that are less clearly transformative in character.

  4. Crafting biochars to reduce N2O and CO2 emissions while also improving soil quality

    Science.gov (United States)

    Novak, Jeff; Ippolito, Jim; Spokas, Kurt; Sigua, Gilbert; Kammann, Claudia; Wrage-Monnig, Nicole; Borchard, Nils; Schirrmann, Michael; Estavillo, Jose Maria; Fuertes-Mendizabal, Teresa; Menendez, Sergio; Cayuela, Maria Luz

    2017-04-01

    Biochar used as an amendment has been linked to nitrous oxide (N2O) emission reductions, a decrease in nitrogen (N) leaching, and soil quality improvements (e.g., soil carbon sequestration, pH, etc.). While numerous articles will support these three facts, conversely, there are reports of no to marginal influences. One reason for the mixed biochar performance could be related to applying biochar with incorrect chemical and physical characteristics. As a means to increase biochar efficiency, we introduced the concept of crafting biochars with properties attuned to specific soil deficiencies. Implementing this concept requires a literature review to identify salient biochar characteristics that reduces N2O emissions, impacts N availability, while also improving soil quality. Thus, scientists from the USDA-ARS and through a coalition of European scientists under the FACCE-JPI umbrella have conceived the DesignChar4food (d4f) project. In this project, scientists are working collaboratively to further this concept to match the appropriate biochar for selective soil quality improvement, retain N for crops, and promote greenhouse gas reductions. This presentation will highlight results from the d4f team compromising a meta-analysis of articles on biochar:N2O dynamics, N availability, and how designer biochars can target specific soil quality improvements.

  5. ANALISA PENGARUH BENTUK LAMBUNG AXE BOW PADA KAPAL HIGH SPEED CRAFT TERHADAP HAMBATAN TOTAL

    Directory of Open Access Journals (Sweden)

    Romadhoni Oni

    2015-06-01

    Full Text Available Hambatan merupakan salah satu faktor utama yang mempengaruhi proses perancangan sebuah kapal. Kapal dengan bentuk lambung yang baik akan menghasilkan hambatan yang efisiensi sehingga operasional kapal dan pergerakan kapal lebih baik. Pada ini penelitian dilakukan dengan memodelkan kapal high speed craft tipe Crew boat panjang 38 meter, lebar 7.6 meter, tinggi 3.65 meter dan draft 1.89 meter. Selanjutnya diselidiki model lambung kapal yang menghasilkan hambatan total paling kecil menggunakan pendekatan studi numerik software (maxsuft hullspeed metode savitsky dan holtrop dan software Computational Fluid Dynamics (CFD. Hasil penelitian berdasarkan analisa numerik (Maxsuft –Hullspeed dan CFD menujukkan pada kecepatan sevice bentuk lambung model AXE Bow memiliki nilai hambatan yang lebih kecil dibandingkan model kapal planing hull chine (HPC dan rounded hull (RH. Hasil perhitungan numerik dan CFD memiliki nilai yang hampir sama pada setiap variasi model. Hasil komparisi yang dilakukan didapatkan selisih total hambatan pada kecepatan 25 knot yaitu  model HPC 1.8 kN, model HPCAB 5.2 kN, model RH 4.8 kN dan model 5.1 kN. Dari perbandingan kedua metode tersebut memiliki selisih cukup kecil yaitu  kurang dari 5%. Selain mendapatkan nilai hambatan Software CFD akan menghasilkan nilai  perbandingan gaya angkat (lift force, dan total pressure yang terdistribusi  pada permukaan model setiap variasi kecepatan.

  6. The craft of writing: a physician-writer's workshop for resident physicians.

    Science.gov (United States)

    Reisman, Anna B; Hansen, Helena; Rastegar, Asghar

    2006-10-01

    How can residency programs help trainees address conflicting emotions about their professional roles and cultivate a curiosity about their patients' lives beyond their diseases? We drew on the medical humanities to address these challenges by creating an intensive writing workshop for internal medicine residents. To help participants become better physicians by reflecting on their experiences and on what gives meaning to work and life. This paper describes the workshop and how residents were affected by the focus on the craft of writing. A group of 15 residents from 3 training programs affiliated with 1 institution. We engaged the expertise of physician-writer Abraham Verghese in planning and facilitating the 2 and one-half day workshop. Residents' submissions were discussed with a focus on the effectiveness of the writing. We also conducted a focus group with participants to evaluate the workshop. Themes in the writing included dysphoria, impotence of the physician, and the healing power of compassion. Our focus group data suggested that this workshop served as a creative outlet from the rigors of medicine, created a sense of community among participants, enhanced both self-awareness and awareness of their patients' lives, and increased intra-institutional and extra-institutional interest in writing and the residency program. Teaching creative writing to residents in an intensive workshop may deepen interactions with peers and patients, improve writing skills, and increase interest in writing and the residency program.

  7. Has the Historian’s craft gone digital? Some observations from France

    Directory of Open Access Journals (Sweden)

    Franziska Heimburger

    2012-06-01

    Full Text Available Since the end of the 1980s the historiographical context has changed considerably. Over the course of the last ten years, we have reached the “digital age” and computers as well as resources available via the Internet have become indispensable tools for all researchers. Be it for the stage of documentation or for actual writing, we are now living and working in a context where historians can no longer completely refuse all IT tools. As long as there are no solid, durable, large-scale training efforts to equip all historians with the skills to use the new and old IT tools, their potential is necessarily limited. While there have been studies on “researchers” in general and also on political scientists in particular, there has, to our knowledge, been no scientific study which would allow us to reach conclusions on the use of IT tools and digital resources by French historians. It is thus difficult to reach conclusions on a larger scale and we have decided to base our analysis on our own experience in order to consider what could be the transformations of the historian’s craft in the digital age. We will thus proceed first to a series of conclusions based on our activities in mediation (teaching and blogging, before proposing a typology of the principal evolutions. We will conclude with a certain number of propositions as far as training of historians is concerned.

  8. Ceramic Production and Craft Specialization in the Prehispanic Philippines, A.D. 500 to 1600

    Science.gov (United States)

    Niziolek, Lisa Christine

    In the millennium prior to Spanish contact, the political economies of lowland societies in the Philippines, such as Tanjay (A.D. 500-1600) on southeastern Negros Island in the central Philippines, underwent significant social, political, and economic changes. Foreign trade with China increased, the circulation of wealth through events such as ritual feasting and bridewealth exchanges expanded, inter-polity competition through slave-raiding and warfare heightened, and agriculture intensified. It also has been hypothesized that the production of craft goods such as pottery and metal implements became increasingly specialized and centralized at polity centers. Tanjay, a historically-known chiefdom, was among them. This dissertation examines changes in the organization of ceramic production using the results of laser ablation-inductively coupled plasma-mass spectrometry analysis of close to 300 ceramic samples. In addition to geochemical analysis, this research draws on Chinese accounts of trade from the late first millennium and early second millennium A.D.; Spanish colonial accounts of exploration and conquest from the sixteenth and seventeenth centuries; ethnographic research on traditional Philippine societies and ceramic production; ethnoarchaeological investigations of pottery production, exchange, and use; and archaeological work that has taken place in the Bais-Tanjay region of Negros Island for more than 30 years. Rather than finding clear evidence that ceramics became more compositionally standardized or homogeneous over time, this analysis reveals that a dynamic and complex pattern of local, dispersed pottery production existed alongside increasingly centralized and specialized production of ceramic materials.

  9. Emergence of quasiparticle Bloch states in artificial crystals crafted atom-by-atom

    Directory of Open Access Journals (Sweden)

    Jan Girovsky, Jose L. Lado, Floris E. Kalff, Eleonora Fahrenfort, Lucas J. J. M. Peters, Joaquín Fernández-Rossier, Alexander F. Otte

    2017-06-01

    Full Text Available The interaction of electrons with a periodic potential of atoms in crystalline solids gives rise to band structure. The band structure of existing materials can be measured by photoemission spectroscopy and accurately understood in terms of the tight-binding model, however not many experimental approaches exist that allow to tailor artificial crystal lattices using a bottom-up approach. The ability to engineer and study atomically crafted designer materials by scanning tunnelling microscopy and spectroscopy (STM/STS helps to understand the emergence of material properties. Here, we use atom manipulation of individual vacancies in a chlorine monolayer on Cu(100 to construct one- and two-dimensional structures of various densities and sizes. Local STS measurements reveal the emergence of quasiparticle bands, evidenced by standing Bloch waves, with tuneable dispersion. The experimental data are understood in terms of a tight-binding model combined with an additional broadening term that allows an estimation of the coupling to the underlying substrate.

  10. From peripheral hamlet to craft beer capital: Apecchio and the ‘Alogastronomia’

    Directory of Open Access Journals (Sweden)

    Maria Giulia Pezzi

    2017-05-01

    Full Text Available In 2012, the Italian Ministry for Territorial Cohesion launched the ‘National Strategy for Inner Areas’ (SNAI, a development strategy aimed at enhancing the quality of life and the access to essential services (health, education and transport in areas considerably far from urban centres, which have been suffering from processes of increasing marginalisation and de-anthropisation since the 1950s. The current contribution focuses on how tourism is locally interpreted in peripheral areas, taking the cue from a wider research on the implementation of SNAI in the Marche’s Apennines carried out between 2015 and 2016. The underlying hypothesis is that the creation of a tourism market in such areas requires, on the one hand, the selection of few cultural traits perceived as more ‘charismatic’, often enhanced through dedicated events, and, on the other, the creation of new potential attractors in line with the expectations of prospective rural tourists. In particular, the ‘Alogastronomia’ phenomenon will be analysed, highlighting the cultural and environmental factors which have brought the local administration to create a territorial marketing strategy linked to a peculiar craft beer and gastronomic culture, and considering whether specific niche tourism can contribute to giving some kind of ‘centrality’ to areas otherwise considered as marginal.

  11. Network ties and survival

    DEFF Research Database (Denmark)

    Acheampong, George; Narteh, Bedman; Rand, John

    2017-01-01

    Poultry farming has been touted as one of the major ways by which poverty can be reduced in low-income economies like Ghana. Yet, anecdotally there is a high failure rate among these poultry farms. This current study seeks to understand the relationship between network ties and survival chances...... of small commercial poultry farms (SCPFs). We utilize data from a 2-year network survey of SCPFs in rural Ghana. The survival of these poultry farms are modelled using a lagged probit model of farms that persisted from 2014 into 2015. We find that network ties are important to the survival chances...... but this probability reduces as the number of industry ties increases but moderation with dynamic capability of the firm reverses this trend. Our findings show that not all network ties aid survival and therefore small commercial poultry farmers need to be circumspect in the network ties they cultivate and develop....

  12. Aircraft Survivability: Rotorcraft Survivability. Summer 2010

    Science.gov (United States)

    2010-01-01

    protect those who serve to protect us?” The answer is a mixed bag. I am fortunate to have joined a group of dedicated men and women who represent this...and Service subject matter experts on rotorcraft safety and survivability to complete the study and report the results to the Joint Chiefs of...Operations and Support CDD TEMP DT DT/OT LUT IOT &E BLRIP TEMP TEMP LRIP Acquisition & LFT Strategies B C LFT&E Review Requirements Approve TEMPs

  13. Study of a 30-M Boom For Solar Sail-Craft: Model Extendibility and Control Strategy

    Science.gov (United States)

    Keel, Leehyun

    2005-01-01

    Space travel propelled by solar sails is motivated by the fact that the momentum exchange that occurs when photons are reflected and/or absorbed by a large solar sail generates a small but constant acceleration. This acceleration can induce a constant thrust in very large sails that is sufficient to maintain a polar observing satellite in a constant position relative to the Sun or Earth. For long distance propulsion, square sails (with side length greater than 150 meters) can reach Jupiter in two years and Pluto in less than ten years. Converting such design concepts to real-world systems will require accurate analytical models and model parameters. This requires extensive structural dynamics tests. However, the low mass and high flexibility of large and light weight structures such as solar sails makes them unsuitable for ground testing. As a result, validating analytical models is an extremely difficult problem. On the other hand, a fundamental question can be asked. That is whether an analytical model that represents a small-scale version of a solar-sail boom can be extended to much larger versions of the same boom. To answer this question, we considered a long deployable boom that will be used to support the solar sails of the sail-craft. The length of fully deployed booms of the actual solar sail-craft will exceed 100 meters. However, the test-bed we used in our study is a 30 meter retractable boom at MSFC. We first develop analytical models based on Lagrange s equations and the standard Euler-Bernoulli beam. Then the response of the models will be compared with test data of the 30 meter boom at various deployed lengths. For this stage of study, our analysis was limited to experimental data obtained at 12ft and 18ft deployment lengths. The comparison results are positive but speculative. To observe properly validate the analytic model, experiments at longer deployment lengths, up to the full 30 meter, have been requested. We expect the study to answer the

  14. Some Phonetic Phenomena in the Central Podillia Dialect (Based on the Terminology of Traditional Folk Crafts

    Directory of Open Access Journals (Sweden)

    Kraievska Hanna

    2016-08-01

    Full Text Available Background: In the reviewed paper we attempted to investigate the phonetic variation of the Central Podillia dialect on the example of some linguistic phenomena. We found out that many linguists studied the phonetic variation based on the Ukrainians' dialect speech. However, they did not study the terminology of folk crafts of the Central Podillia dialects, that's why we aim to describe the sound differences of the lexical units of this area. Purpose: The purpose of the analysis is to determine some phonetic phenomena of the Central Podillia dialect. First of all, there are changes within the stable word length (metathesis, substantive changes of one sound in the stable surround sound, and changes, accompanied by the word elongation or contraction (prosthesis, epenthesis, elision. Results: The analyzed dialects widely present the consonant changes within the stable word length (г → ґ, т → д, с → ш, з → ж…. The performed study characterizes the Central Podillia dialects by the vowel change within a stable word length – 5 cases. Sound changes are typical for the analyzed dialects affecting the dynamics of the word length (prosthetic sounds - [г], [в], [й], [і], [и]. In opposition to the phonetic processes that help to increase the length of the word, we observe the loss of the sound in the middle of the word in the Central Podillia dialects (reduction – [o], [й], [в]. Discussion: The analysis of some phonetic phenomena of the Central Podillia dialects proved the existence of phonetic features typical for the South-Western dialect. However, we determined the local sound differences of this area, which confirm the identity of the language of this region.

  15. Radiation damage of variscite in historic crafts: Solarization, decolouration, structural changes and spectra from ionoluminescence

    Science.gov (United States)

    Garcia-Guinea, J.; Correcher, V.; Sanchez-Muñoz, L.; Lopez-Arce, P.; Townsend, P. D.; Hole, D. E.

    2008-01-01

    X-ray diffraction measurements, during halogen lamp illumination to simulate sunlight, (TXRD) show a phase transition from variscite (AlPO 4·H 2O) Messbach to variscite Lucin and a loss of the dark green colour. The differential-thermal and thermo-gravimetric (DTA-TG) analyses and thermoluminescence (TL) peaks all depict this first-order phase transition which takes place under sunlight. From the water vaporization temperature up to circa 650 °C, a second-order phase transition progressively occurs from variscite to berlinite (AlPO 4) by loss of a second unit of water with hydrogen bonded to the lattice. The ion beam luminescence (IBL) spectra of the Zamora variscite display a spectral band from 500 to 570 nm attributed to [UO 2] 2+ in phosphates, and another spectral band from 670 to 740 nm is linked with Cr(VI) 3+ defects situated in octahedral Al(VI) 3+ positions. In the hydrous variscite lattice, the Al-O and P-O chemical bonds are mainly covalent; with the degree of covalency of the P-O chemical bond significantly larger than of Al-O. This open structure of variscite, which has a crystal field of reduced strength, involves small shifts of the absorption bands which intensify the blue-green transmission producing the characteristic emerald colour of the dark green variscite of Zamora. These data provide a valuable basis for detection of solarization damage in historic crafts with inlaid variscite in the Museo del Prado (Madrid, Spain).

  16. Postural Stability of Special Warfare Combatant-Craft Crewmen With Tactical Gear.

    Science.gov (United States)

    Morgan, Paul M; Williams, Valerie J; Sell, Timothy C

    The US Naval Special Warfare's Special Warfare Combatant-Craft Crewmen (SWCC) operate on small, high-speed boats while wearing tactical gear (TG). The TG increases mission safety and success but may affect postural stability, potentially increasing risk for musculoskeletal injury. Therefore, the purpose of this study was to examine the effects of TG on postural stability during the Sensory Organization Test (SOT). Eight SWCC performed the SOT on NeuroCom's Balance Manager with TG and with no tactical gear (NTG). The status of gear was performed in randomized order. The SOT consisted of six different conditions that challenge sensory systems responsible for postural stability. Each condition was performed for three trials, resulting in a total of 18 trials. Overall performance, each individual condition, and sensory system analysis (somatosensory, visual, vestibular, preference) were scored. Data were not normally distributed therefore Wilcoxon signed-rank tests were used to compare each variable (ρ = .05). No significant differences were found between NTG and TG tests. No statistically significant differences were detected under the two TG conditions. This may be due to low statistical power, or potentially insensitivity of the assessment. Also, the amount and distribution of weight worn during the TG conditions, and the SWCC's unstable occupational platform, may have contributed to the findings. The data from this sample will be used in future research to better understand how TG affects SWCC. The data show that the addition of TG used in our study did not affect postural stability of SWCC during the SOT. Although no statistically significant differences were observed, there are clinical reasons for continued study of the effect of increased load on postural stability, using more challenging conditions, greater surface perturbations, dynamic tasks, and heavier loads. 2016.

  17. Proof-Carrying Survivability

    Science.gov (United States)

    2013-01-15

    pp.289-302 ( Impact factor : 2.09). 2. Julic, J. and Zuo, Y. (2012). “An RFID Survivability Impact Model in the Military Domain”, Proc. of 18 th...Availability, Reliability and Security, 40(4), pp. 406-418 ( Impact factor : 2.016). 10. Zuo, Y. (2010). “A Holistic Approach for Specification of Security... Impact factor : 1.596). 20. Zuo, Y., Pimple, M. and Lande, S. (2009). “A Framework for RFID Survivability Requirement Analysis and Specification”, Proc

  18. TRADITIONAL CRAFTS AND FOLKLORE AS A MEANS OF ECONOMIC DEVELOPMENT IN THE LAND OF CĂLATA

    Directory of Open Access Journals (Sweden)

    Roxana-Maria BUŞ

    2017-04-01

    Full Text Available The main purpose of this paper is to demonstrate how territorial identity, expressed through immaterial and material heritage, especially folklore and traditional crafts, can be a means of economic sustainable development in rural areas. As a case study, we choose the Land of Călata (Hu. Kalotaszeg, a region from North-Western Transylvania, Romania, focusing on two of its best-known villages: Izvoru Crișului (Hu. Körösfő and Sâncraiu (Hu. Kalotaszentkirály. Izvoru Crișului is appreciated for carpentry and handicrafts products, whilst Sâncraiu is well-known for its Hungarian folk music and dance festival. In order to illustrate how these activities can lead to economic development, we interviewed a craftsman family from Izvoru Crișului and a dance instructor, cofounder of the International folk music and dance camp that is held annually in Sâncraiu. We also analysed several handicrafts stalls from Izvoru Crișului to see exactly what kind of products were being sold in there. The results show that even though traditional crafts could generate an income for the local people, most of the products sold in Izvoru Crișului are not authentic, but brought there from other regions of Romania or abroad. On the other hand, the international folk music and dance camp from Sâncraiu is the best example of how a one-week event can help local economy by generating income for various stakeholders involved in the organisation and realisation of the event, and be the igniter of a larger agro-touristic activity. In the end, we concluded with several remarks concerning the need for raising awareness among the locals how to benefit from their cultural heritage and traditional occupations and we acknowledged the potential of traditional crafts and folklore as a means of diversifying income possibilities in rural areas.

  19. Survivability via Control Objectives

    Energy Technology Data Exchange (ETDEWEB)

    CAMPBELL,PHILIP L.

    2000-08-11

    Control objectives open an additional front in the survivability battle. A given set of control objectives is valuable if it represents good practices, it is complete (it covers all the necessary areas), and it is auditable. CobiT and BS 7799 are two examples of control objective sets.

  20. Artists’ Survival Rate

    DEFF Research Database (Denmark)

    Bille, Trine; Jensen, Søren

    2017-01-01

    The literature of cultural economics generally finds that an artistic education has no significant impact on artists’ income and careers in the arts. In our research, we have readdressed this question by looking at the artists’ survival in the arts occupations. The results show that an artistic...... education has a significant impact on artists’ careers in the arts and we find important industry differences....

  1. Education for Survival

    Science.gov (United States)

    Aldrich, Richard

    2010-01-01

    This article provides a brief overview of current approaches to education and concludes that none of these is sufficient to meet the challenges that now face the human race. It argues instead for a new concept of education for survival. (Contains 1 note.)

  2. Flexible survival regression modelling

    DEFF Research Database (Denmark)

    Cortese, Giuliana; Scheike, Thomas H; Martinussen, Torben

    2009-01-01

    Regression analysis of survival data, and more generally event history data, is typically based on Cox's regression model. We here review some recent methodology, focusing on the limitations of Cox's regression model. The key limitation is that the model is not well suited to represent time-varyi...

  3. Seeds to survive

    NARCIS (Netherlands)

    Groot, S.P.C.

    2002-01-01

    Seeds are important for man, either as propagation material of crops or directly for the production of foods, fodder and drinks. The natural function of seeds is dispersal of its genes to successive generations. Survival mechanisms seed have evolved sometimes interfere with those preferred by

  4. Survival After Retirement.

    Science.gov (United States)

    Holloway, Clark; Youngblood, Stuart A.

    1986-01-01

    Examined survival rates after retirement in a large corporation. A regression analysis was performed to control for age, sex, job status, and type of work differences that may influence longevity. Short-term suvivors seemed to undergo a different adjustment process than long-term survivors. (Author/ABL)

  5. An art-based healing process: The Aurukun creative livelihoods project at the Wik and Kugu Arts and Craft Centre.

    Science.gov (United States)

    Allain, Guy

    2011-07-01

    This paper describes the challenges in implementing an innovative arts-based mental health project in a remote Indigenous community. The author (the Art Centre Manager) presents a personal narrative of the development of the Aurukun Creative Livelihoods project. A partnership between an existing arts and mental health project (Creative Recovery) and the Wik and Kugu Arts and Craft Centre is described. This collaboration aims to enhance the emotional and social wellbeing of vulnerable Aboriginal people in a remote Indigenous community in Cape York - Aurukun.

  6. A novel mesoporous sulfated zirconium solid acid catalyst for Friedel-Crafts benzylation reaction

    Energy Technology Data Exchange (ETDEWEB)

    Miao, Zhichao; Zhou, Jin; Zhao, Jinping; Liu, Dandan; Bi, Xu [School of Chemical Engineering, Shandong University of Technology, Zibo, 255049 (China); Chou, Lingjun, E-mail: ljchou@licp.cas.cn [State Key Laboratory for Oxo Synthesis and Selective Oxidation, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou, 730000 (China); Zhuo, Shuping, E-mail: zhuosp_academic@yahoo.com [School of Chemical Engineering, Shandong University of Technology, Zibo, 255049 (China)

    2017-07-31

    Highlights: • A novel mesoporous ZrO{sub 2}/SO{sub 4}{sup 2−} has been prepared via a facile one-pot EISA strategy. • The M-ZrO{sub 2}/SO{sub 4}{sup 2−} exhibited excellent textural and acidic properties. • The introduced S species were homogeneously dispersed in mesoporous skeleton. • The M-ZrO{sub 2}/SO{sub 4}{sup 2−} exhibited excellent catalytic performance and reusability. - Abstract: In this paper, a novel mesoporous sulfated zirconium (M-ZrO{sub 2}/SO{sub 4}{sup 2−}) has been gotten by one-pot evaporation-induced self-assembly (one-pot EISA) strategy. The SXRD, N{sub 2}-physisorption and TEM characterization techniques indicated that M-ZrO{sub 2}/SO{sub 4}{sup 2−} possessed distinct mesostructure with big specific surface area (133.5 m{sup 2} g{sup −1}), large pore volume (0.18 cm{sup 3} g{sup −1}) and narrow pore size distribution (4.90 nm). Moreover, the existing states and the influence in mesostructure of introduced S species were detailedly investigated by the XRD, N{sub 2}-physisorption, TEM, TG-DSC, FT-IR and XPS techniques and the results showed that the S species, which existed as the type of SO{sub 4}{sup 2−}, improved the textural properties of prepared materials. In addition, the NH{sub 3}-TPD and IR spectra of adsorbed pyridine indicated the existence of strong Brønsted and Lewis acid sites in M-ZrO{sub 2}/SO{sub 4}{sup 2−} even evacuated at 400 °C. Furthermore, the M-ZrO{sub 2}/SO{sub 4}{sup 2−} was used as a promise solid acid catalyst and displayed excellent catalytic performance and reusability in Friedel-Crafts benzylation reaction.

  7. The Aura of the Analogue in a Digital Age: Women’s Crafts, Creative Markets and Home-Based Labour After Etsy

    Directory of Open Access Journals (Sweden)

    Susan Luckman

    2013-02-01

    Full Text Available This article examines the renewed popularity of the handmade by examining the current renaissance in the street credibility of previously disparaged women's craft practices, particularly those employing yarn (for example knitting, crochet, needlepoint and weaving and fabric (sewing, felting. The author historically locates current debates around craft production and creative work by drawing upon the British Arts and Crafts movement, with its own longstanding association with women's' labour in the home and desire to realise sustainable ethical labour practices. Notably, both the periods under discussion mark profound shifts in the economic organisation of society – then, the Industrial Revolution; now the de-industrialisation of much of the 'industrialised' world and the rise of the (digitised knowledge economy – and see a concurrent increase in the popularity of the handmade original as a desirable aesthetic object.

  8. Pupils' Activities in a Multimaterial Learning Environment in Craft subject A Pilot Study using an Experience Sampling Method based on a Mobile Application in Classroom Settings

    Directory of Open Access Journals (Sweden)

    Juha Jaatinen

    2017-12-01

    Full Text Available This study investigates holistic craft processes in craft education with an instrument for data-collection and self-assessment. Teaching in a study context is based on co-teaching and a design process, highlighted by the Finnish Basic Education Core Curriculum 2014. The school architecture and web-based learning environment is combined. Division for textiles and technical work is no longer supported in this multimaterial learning environment. The aim of the study is to 1 make pupils’ holistic craft processes visible in everyday classroom practices with information collected by a mobile-application and 2 point out the curriculum topics that are covered during everyday classroom practices as defined by the teachers. The data is collected using an Experience Sampling Method with a gamified learning analytics instrument. Teachers’ classroom activities were used as the backbone for the thematic mapping of the craft curriculum. Preliminary measurements were carried out in a Finnish primary school in grades 5–6 (age 10–12, n = 125 during a four-week period in October-November 2016. The list of classroom activities was updated after the four weeks’ experiment and was tested in March-May 2017 with all the pupils of the pilot school (N = 353. The key findings were that a for pupils the self-assessment was easy as a technical process but there were several factors in the everyday classroom settings that made the process challenging and b it was relatively difficult for teachers to describe the classroom activities in terms of the new curriculum; however, after four weeks they could not only described the activities in more details but had also developed new activities that supported the ideas of the new curriculum better.Keywords: multi-material craft, learning environment, holistic craft process, experience sampling method

  9. Surviving Sepsis Campaign

    DEFF Research Database (Denmark)

    Rhodes, Andrew; Evans, Laura E; Alhazzani, Waleed

    2017-01-01

    OBJECTIVE: To provide an update to "Surviving Sepsis Campaign Guidelines for Management of Sepsis and Septic Shock: 2012". DESIGN: A consensus committee of 55 international experts representing 25 international organizations was convened. Nominal groups were assembled at key international meetings......, and to formulate recommendations as strong or weak, or best practice statement when applicable. RESULTS: The Surviving Sepsis Guideline panel provided 93 statements on early management and resuscitation of patients with sepsis or septic shock. Overall, 32 were strong recommendations, 39 were weak recommendations...... of care have relatively weak support, evidence-based recommendations regarding the acute management of sepsis and septic shock are the foundation of improved outcomes for these critically ill patients with high mortality....

  10. Surviving Sepsis Campaign

    DEFF Research Database (Denmark)

    Rhodes, Andrew; Evans, Laura E; Alhazzani, Waleed

    2017-01-01

    OBJECTIVE: To provide an update to "Surviving Sepsis Campaign Guidelines for Management of Sepsis and Septic Shock: 2012." DESIGN: A consensus committee of 55 international experts representing 25 international organizations was convened. Nominal groups were assembled at key international meetings......, and to formulate recommendations as strong or weak, or best practice statement when applicable. RESULTS: The Surviving Sepsis Guideline panel provided 93 statements on early management and resuscitation of patients with sepsis or septic shock. Overall, 32 were strong recommendations, 39 were weak recommendations...... of care have relatively weak support, evidence-based recommendations regarding the acute management of sepsis and septic shock are the foundation of improved outcomes for these critically ill patients with high mortality....

  11. Modification of an Amposta origin bitumen by using tlie Friedel and Crafts reaction with toluyiene-2,4-diisocyanate

    Directory of Open Access Journals (Sweden)

    Blanco, M.

    1988-03-01

    Full Text Available In this works, we have modified a bitumen from Amposta by using the Friedel and Crafts reaction with toluylene-2,4-diisocyanate in presence of aluminium trichloride, presenting as well as the characteristics of the original bitumen as the ones of the modification products. We have made technological test, aging of thin film, rheological test, thermical susceptibility and components analyses.

    En el presente trabajo se ha modificado un betún procedente de Amposta por reacción de Friedei y Crafts con 4-metil-1,3-bencenodiisocianato, en presencia de tricloruro de aluminio. Se han determinado las características del betún original así como las de los productos obtenidos en la modificación. Se han llevado a cabo ensayos de tipo tecnológico, envejecimiento en película delgada, propiedades reológicas, susceptibilidad térmica y análisis de componentes.

  12. Application of a Spectral Wave Model to Assess Breakwater Configurations at a Small Craft Harbour on Lake Ontario

    Directory of Open Access Journals (Sweden)

    Amelia H. Cooper

    2016-08-01

    Full Text Available A surface wave model using three nested grids is applied to the eastern end of Lake Ontario to investigate wave propagation from an open lake environment to a small craft harbour protected by a breakwater. The Simulating WAves Nearshore (SWAN spectral wave model, coupled with the Delft3D hydrodynamic model, is applied to simulate a series of storms in November, 2013. The model results are compared to observations from two pressure sensors, and used to quantify wave properties around existing and future breakwaters to evaluate the bulk changes to the harbour configuration. Overall, the results indicate that the rubblemound breakwater reduces wave heights in the existing harbour by 63% compared to no breakwater, and that the addition of a surface breakwater extension could reduce wave heights by an additional 54%. Wave height attenuation was found to be highly dependent on the incident wave direction relative to breakwater orientation. The spectral wave model is useful for simulating wave transformation for broad directional spectra in wind-sea conditions over large scales to semi-protected areas such as small craft harbours.

  13. The Eco-Innovation Variables which Influence the Performance of Creative Industries Center of Natural Stone Crafts

    Directory of Open Access Journals (Sweden)

    Murti Astuti

    2018-01-01

    Full Text Available This study investigates the eco-innovation variable which has the significant effecton creative industries center’s performance of marble and natural stone craft sector in Tulungagung, Indonesia. The object of the study is the creative industries center with the non-renewable raw material. Mostly, the companies are in form of small and medium-sized enterprises (SMEs which is ‘passive eco-innovator’ and their eco-innovation variables have not been investigated before in terms of their influenceon their performance. The respondents were 81 craftsmen taken from the population. The data were collected through questionnaires which were tested, processed and analyzed by using Consistent Partial Least Square (PLSc. The eco-innovation variables which significantly effecton innovative performance are eco-organizational innovation and eco-product innovation. Eco-process innovation and eco-marketing innovation don’t directly affecton innovative performance, but its significant effecton eco-product innovation may influence innovative performance. Improving innovative performance will impact on financial performance through improvement of production performance, but market performance does not significantly affect financial performance. The findings of this study could be a reference for creative industries center’s of marble and natural stone craft sector to prioritize which type of eco-innovation should be improved so that its impact on performance is more significant

  14. The building blocks of drinking experience across men and women: A case study with craft and industrial beers.

    Science.gov (United States)

    Gómez-Corona, Carlos; Escalona-Buendía, Héctor B; Chollet, Sylvie; Valentin, Dominique

    2017-09-01

    In today's market, every product seems to be marked by the label of "experience". It is expected that successful products give the consumer "extraordinary experiences". The research in consumption experience is growing, but much work still needs to be done to understand the food and beverage experience. A qualitative study was conducted using contextual focus groups to explore the building blocks of consumers' drinking experience of industrial and craft beers. The results show that drinking experience is shaped by our cognitive, sensory or affective systems, especially during the core consumption experience. Elements such as attitudes, consumption habits, and individual versus social consumption, shopping experience and product benefits are also responsible for shaping the experience, but are more relevant during the pre-consumption or post-consumption experience. Gender differences occur more frequently in the affective experience, as women search more for relaxation while men for excitement and stimulation while drinking beer. When comparing industrial users versus craft, in the latter the cognitive and shopping experiences are more relevant. Overall, the results showed that the drinking experience of beers can be studied as a function of the salient human system used during product interaction, and this systems act as the building blocks of the drinking experience of beer. This information can be applied in consumer research studies to further study the experiential differences across products and consumers. Copyright © 2017 Elsevier Ltd. All rights reserved.

  15. Cracking the survival code

    Science.gov (United States)

    Füllgrabe, Jens; Heldring, Nina; Hermanson, Ola; Joseph, Bertrand

    2014-01-01

    Modifications of histones, the chief protein components of the chromatin, have emerged as critical regulators of life and death. While the “apoptotic histone code” came to light a few years ago, accumulating evidence indicates that autophagy, a cell survival pathway, is also heavily regulated by histone-modifying proteins. In this review we describe the emerging “autophagic histone code” and the role of histone modifications in the cellular life vs. death decision. PMID:24429873

  16. Artillery Survivability Model

    Science.gov (United States)

    2016-06-01

    experiment mode also enables users to set their own design of experiment by manipulating an editable CSV file. The second one is a real-time mode that...renders a 3D virtual environment of a restricted battlefield where the survivability movements of an artillery company are visualized . This mode...provides detailed visualization of the simulation and enables future experimental uses of the simulation as a training tool. 14. SUBJECT TERMS

  17. Survival analysis models and applications

    CERN Document Server

    Liu, Xian

    2012-01-01

    Survival analysis concerns sequential occurrences of events governed by probabilistic laws.  Recent decades have witnessed many applications of survival analysis in various disciplines. This book introduces both classic survival models and theories along with newly developed techniques. Readers will learn how to perform analysis of survival data by following numerous empirical illustrations in SAS. Survival Analysis: Models and Applications: Presents basic techniques before leading onto some of the most advanced topics in survival analysis.Assumes only a minimal knowledge of SAS whilst enablin

  18. Applied survival analysis using R

    CERN Document Server

    Moore, Dirk F

    2016-01-01

    Applied Survival Analysis Using R covers the main principles of survival analysis, gives examples of how it is applied, and teaches how to put those principles to use to analyze data using R as a vehicle. Survival data, where the primary outcome is time to a specific event, arise in many areas of biomedical research, including clinical trials, epidemiological studies, and studies of animals. Many survival methods are extensions of techniques used in linear regression and categorical data, while other aspects of this field are unique to survival data. This text employs numerous actual examples to illustrate survival curve estimation, comparison of survivals of different groups, proper accounting for censoring and truncation, model variable selection, and residual analysis. Because explaining survival analysis requires more advanced mathematics than many other statistical topics, this book is organized with basic concepts and most frequently used procedures covered in earlier chapters, with more advanced topics...

  19. Survival after blood transfusion

    DEFF Research Database (Denmark)

    Kamper-Jørgensen, Mads; Ahlgren, Martin; Rostgaard, Klaus

    2008-01-01

    of transfusion recipients in Denmark and Sweden followed for up to 20 years after their first blood transfusion. Main outcome measure was all-cause mortality. RESULTS: A total of 1,118,261 transfusion recipients were identified, of whom 62.0 percent were aged 65 years or older at the time of their first...... the SMR remained significantly 1.3-fold increased. CONCLUSION: The survival and relative mortality patterns among blood transfusion recipients were characterized with unprecedented detail and precision. Our results are relevant to assessments of the consequences of possible transfusion-transmitted disease...... as well as for cost-benefit estimation of new blood safety interventions....

  20. Nuclear War Survival Skills

    Energy Technology Data Exchange (ETDEWEB)

    Kearny, C.H.

    2002-06-24

    The purpose of this book is to provide Americans with information and instructions that will significantly increase their chances of surviving a possible nuclear attack. It brings together field-tested instructions that, if followed by a large fraction of Americans during a crisis that preceded an attack, could save millions of lives. The author is convinced that the vulnerability of our country to nuclear threat or attack must be reduced and that the wide dissemination of the information contained in this book would help achieve that objective of our overall defense strategy.

  1. Design of survivable networks

    CERN Document Server

    Stoer, Mechthild

    1992-01-01

    The problem of designing a cost-efficient network that survives the failure of one or more nodes or edges of the network is critical to modern telecommunications engineering. The method developed in this book is designed to solve such problems to optimality. In particular, a cutting plane approach is described, based on polyhedral combinatorics, that is ableto solve real-world problems of this type in short computation time. These results are of interest for practitioners in the area of communication network design. The book is addressed especially to the combinatorial optimization community, but also to those who want to learn polyhedral methods. In addition, interesting new research problemsare formulated.

  2. Enhancing Video Games Policy Based on Least-Squares Continuous Action Policy Iteration: Case Study on StarCraft Brood War and Glest RTS Games and the 8 Queens Board Game

    Directory of Open Access Journals (Sweden)

    Shahenda Sarhan

    2016-01-01

    Full Text Available With the rapid advent of video games recently and the increasing numbers of players and gamers, only a tough game with high policy, actions, and tactics survives. How the game responds to opponent actions is the key issue of popular games. Many algorithms were proposed to solve this problem such as Least-Squares Policy Iteration (LSPI and State-Action-Reward-State-Action (SARSA but they mainly depend on discrete actions, while agents in such a setting have to learn from the consequences of their continuous actions, in order to maximize the total reward over time. So in this paper we proposed a new algorithm based on LSPI called Least-Squares Continuous Action Policy Iteration (LSCAPI. The LSCAPI was implemented and tested on three different games: one board game, the 8 Queens, and two real-time strategy (RTS games, StarCraft Brood War and Glest. The LSCAPI evaluation proved superiority over LSPI in time, policy learning ability, and effectiveness.

  3. PRODUCTION WORKSHOP AT HOME: CULTURAL ELEMENT AND SURVIVAL STRATEGY IN THE REGION P'URHEPECHA

    Directory of Open Access Journals (Sweden)

    Rigoberto Sandoval-Contreras

    2013-04-01

    Full Text Available The aim of this paper is to analyze, characterize and give a definition of home workshop production from wood craft activities performed by residents of San Juan Pamatácuaro, Michoacán. For its realization, from an ethnographic perspective had to live for a time in the community study and thus directly observe workspaces artisans and learn in their own words of their organization in different ways, as the establishment of a workshop is given in the domestic space, the tools that are used have certain peculiarities, labor usually takes familiar, coupled required part marketing or networking. Furthermore, learning from each of the trades is through socialization and observation. Thus the formation of these productive activities turn out to be a survival strategy just for families to meet their needs because they do not generate surpluses.

  4. The Influence of Teaching Methods and Learning Environment to the Student's Learning Achievement of Craft and Entrepreneurship Subjects at Vocational High School

    Science.gov (United States)

    Munawaroh

    2017-01-01

    This research aims to explain the influence of teacher's teaching methods and learning environment to the learning achievement in class XI with the competency of accounting expertise to the subjects of craft and entrepreneurship, according to the students, the subject was very heavy and dull. The population in this research are students in class…

  5. Selling an Energy Efficiency Loan Portfolio in Oregon: Resale of the Craft3 loan portfolio to Self-Help Credit Union

    Energy Technology Data Exchange (ETDEWEB)

    Thompson, Peter; Borgeson, Merrian; Kramer, Chris; Zimring, Mark; Goldman, Charles

    2014-05-30

    Under the Clean Energy Works (CEW) program, Craft3 developed a loan product that widened access to financing for homeowners, offered long term funding, and collected repayments through the customer?s utility bill. The program?s success led Craft3 to pursue the sale of the loan portfolio to both mitigate its own risks and replenish funds for lending. This sale breaks new ground for energy efficiency finance and is notable as it was completed even with many novel program design elements. It replenished Craft3?s program capital and uncovered some valuable lessons that may facilitate future transactions. However, the lack of data history and the unproven nature of the loan portfolio meant that Craft3 had to limit the risk of losses to Self-Help, the purchaser of the portfolio. It remains to be seen whether this experience will pave the way for more sales of on-bill energy efficiency loan portfolios. This case study illustrates how certain program design decisions can sometimes both facilitate programmatic objectives and possibly present challenges for the sale of a portfolio of energy efficiency loans.

  6. Choosing Content and Methods: Focus Group Interviews with Faculty Teachers in Norwegian Pre-Service Subject Teacher Education in Design, Art, and Crafts

    Science.gov (United States)

    Gulliksen, Marte S.; Hjardemaal, Finn R.

    2016-01-01

    The study is aimed at generating knowledge on how faculty teachers reflect and justify their choice of subject content logic in teacher education, exemplified by a concurrent pre-service Subject Teacher Education in design, art, and crafts. Focus-group interviews generated data. Three topics were discussed: too many choices, different logics, and…

  7. Reading the dental record : a dental anthropological approach to foodways, health and disease, and crafting in the pre-Columbian Caribbean

    NARCIS (Netherlands)

    Mickleburgh, Hayley Louise

    2013-01-01

    Reading the Dental Record investigates human foodways, health and disease, and certain (gender-related) craft activities in the pre-Columbian Caribbean archipelago, through integrated analyses of patterns of dental wear and pathology in a large number of skeletal remains from the region.

  8. A Research-Based Undergraduate Organic Laboratory Project: Investigation of a One-Pot, Multicomponent, Environmentally Friendly Prins-Friedel-Crafts-Type Reaction

    Science.gov (United States)

    Dintzner, Matthew R.; Maresh, Justin J.; Kinzie, Charles R.; Arena, Anthony F.; Speltz, Thomas

    2012-01-01

    Students in the undergraduate organic laboratory synthesize tetrahydro-2-(4-nitrophenyl)-4-phenyl-2"H"-pyran via the Montmorillonite K10 clay-catalyzed reaction of p-nitrobenzaldehye with methanol, 3-buten-1-ol, and benzene. The synthesis comprises an environmentally friendly tandem Prins-Friedel-Crafts-type multicomponent reaction (MCR) and sets…

  9. Highly enantioselective Friedel-Crafts alkylation reaction catalyzed by rosin-derived tertiary amine-thiourea: synthesis of modified chromanes with anticancer potency.

    Science.gov (United States)

    Jiang, Xianxing; Wu, Lipeng; Xing, Yanhong; Wang, Long; Wang, Shoulei; Chen, Zongyao; Wang, Rui

    2012-01-11

    We present herein for the first time the synthesis and preliminary biological evaluation of various modified chromanes via a rosin-derived tertiary amine-thiourea-catalyzed highly enantioselective Friedel-Crafts alkylation reaction. This journal is © The Royal Society of Chemistry 2012

  10. Friedel-Craft Acylation of ar-Himachalene: Synthesis of Acyl-ar-Himachalene and a New Acyl-Hydroperoxide

    Directory of Open Access Journals (Sweden)

    Abdallah Karim

    2011-07-01

    Full Text Available Friedel-Craft acylation at 100 °C of 2,5,9,9-tetramethyl-6,7,8,9-tetrahydro-5H-benzocycloheptene [ar-himachalene (1], a sesquiterpenic hydrocarbon obtained by catalytic dehydrogenation of α-, β- and γ-himachalenes, produces a mixture of two compounds: (3,5,5,9-tetramethyl-6,7,8,9-tetrahydro-5H-benzocyclohepten-2-yl-ethanone (2, in 69% yield, with a conserved reactant backbone, and 3, with a different skeleton, in 21% yield. The crystal structure of 3 reveals it to be 1-(8-ethyl-8-hydroperoxy-3,5,5-trimethyl-5,6,7,8-tetrahydronaphthalen-2-yl-ethanone. In this compound O-H…O bonds form dimers. These hydrogen-bonds, in conjunction with weaker C-H…O interactions, form a more extended supramolecular arrangement in the crystal.

  11. Mary Carruthers & Jan M. Ziolkowski (dir.), The Medieval Craft of Memory. An Anthology of Texts and Pictures

    OpenAIRE

    Lejbowicz, Max

    2008-01-01

    Mary Carruthers et Jan M. Ziolkowski ont réuni neuf collaborateurs pour compléter avec cette anthologie deux des livres publiés précédemment par la première : The Book of Memory : A Study of Memory in Medieval Culture, Cambridge, 1990 et The Craft of Thought : Meditation, Rhetoric, and the Making of Images, 400-1200, Cambridge, 1998. Ces deux titres sont maintenant accessibles en français : Le Livre de la Mémoire. Une étude de la mémoire dans la culture médiévale, traduit de l’anglais par Dia...

  12. Metal halide hydrates as lewis acid catalysts for the conjugated friedel-crafts reactions of indoles and activated olefins

    Energy Technology Data Exchange (ETDEWEB)

    Schwalm, Cristiane S.; Ceschi, Marco Antonio; Russowsky, Dennis, E-mail: dennis@iq.ufrgs.b [Universidade Federal do Rio Grande do Sul (IQ/UFRGS), Porto Alegre, RS (Brazil). Inst. de Quimica

    2011-07-01

    Metal halide hydrates such as SnCl{sub 2{center_dot}}2H{sub 2}O, MnCl{sub 2{center_dot}}4H{sub 2}O, SrCl{sub 2{center_dot}}6H{sub 2}O, CrCl{sub 2{center_dot}}6H{sub 2}O, CoCl{sub 2{center_dot}}6H{sub 2}O e CeCl{sub 3{center_dot}}7H{sub 2}O were investigated as mild Lewis acids catalysts for the conjugate Friedel-Crafts reaction between indoles and activated olefins. The reactions were carried out with aliphatic unsaturated ketones over a period of days at room temperature, while chalcones reacted only under reflux conditions. The reactions with nitrostyrene s were either performed in solvent or under solventless conditions. In all cases reasonable to good yields were obtained. (author)

  13. Reasons to keep making crafts in México: Similarities and differences between current artisanal Chiapas and Jalisco

    Directory of Open Access Journals (Sweden)

    Perla Shiomara del Carpio Ovando

    2013-01-01

    Full Text Available To present and to discuss two research communities of artisans in Mexico is the goal in this document. The work is the result of a large study with an indigenous artisans Tzotil of Chiapas and potters artisans of Tonalá, Jalisco. The aim was to find some elements that allowed the permanence of traditional craft in both contexts. For this reason, we will discuss in this article what we understand for handicrafts and the development of the artisan work in the Mexicancontext. Also, we present the case studies we conducted and some of the findings results. For example, some of the reasons for artisan people to continue making handicrafts such as the cultural need lived by these communities and the interiorized discourse about the commitment to continue with the tradition of doing this work.

  14. OBESITY IN CANCER SURVIVAL

    Science.gov (United States)

    Parekh, Niyati; Chandran, Urmila; Bandera, Elisa V.

    2013-01-01

    Although obesity is a well known risk factor for several cancers, its role on cancer survival is poorly understood. We conducted a systematic literature review to assess the current evidence evaluating the impact of body adiposity on the prognosis of the three most common obesity-related cancers: prostate, colorectal, and breast. We included 33 studies of breast cancer, six studies of prostate cancer, and eight studies of colorectal cancer. We note that the evidence over-represents breast cancer survivorship research and is sparse for prostate and colorectal cancers. Overall, most studies support a relationship between body adiposity and site-specific mortality or cancer progression. However, most of the research was not specifically designed to study these outcomes and, therefore, several methodological issues should be considered before integrating their results to draw conclusions. Further research is urgently warranted to assess the long-term impact of obesity among the growing population of cancer survivors. PMID:22540252

  15. Surviving relatives after suicide

    DEFF Research Database (Denmark)

    Nørrelykke, Helle; Cohrt, Pernille

    suicide in Denmark. This means that at least 400 people undergo the trauma it is when one of their near relatives commits suicide. We also know that the loss from suicide involves a lot of conflicting feelings - like anger, shame, guilt and loss and that the lack of therapy/treatment of these difficult...... and conflicting feelings may result in pathological expansion of grief characterized by extremely reduced quality of life involving severe psychical and social consequences. Suicide a subject of taboo In the 1980s WHO drafted a health policy document (‘Health for all year 2000’) with 38 targets for attaining......We would like to focus on the surviving relatives after suicides, because it is generally accepted that it is especially difficult to recover after the loss from suicide and because we know as a fact that one suicide affects five persons on average. Every year approximately 700 people commit...

  16. Obesity in cancer survival.

    Science.gov (United States)

    Parekh, Niyati; Chandran, Urmila; Bandera, Elisa V

    2012-08-21

    Although obesity is a well-known risk factor for several cancers, its role on cancer survival is poorly understood. We conducted a systematic literature review to assess the current evidence evaluating the impact of body adiposity on the prognosis of the three most common obesity-related cancers: prostate, colorectal, and breast. We included 33 studies of breast cancer, six studies of prostate cancer, and eight studies of colo-rectal cancer. We note that the evidence overrepresents breast cancer survivorship research and is sparse for prostate and colorectal cancers. Overall, most studies support a relationship between body adiposity and site-specific mortality or cancer progression. However, most of the research was not specifically designed to study these outcomes and, therefore, several methodological issues should be considered before integrating their results to draw conclusions. Further research is urgently warranted to assess the long-term impact of obesity among the growing population of cancer survivors.

  17. Candida survival strategies.

    Science.gov (United States)

    Polke, Melanie; Hube, Bernhard; Jacobsen, Ilse D

    2015-01-01

    Only few Candida species, e.g., Candida albicans, Candida glabrata, Candida dubliniensis, and Candida parapsilosis, are successful colonizers of a human host. Under certain circumstances these species can cause infections ranging from superficial to life-threatening disseminated candidiasis. The success of C. albicans, the most prevalent and best studied Candida species, as both commensal and human pathogen depends on its genetic, biochemical, and morphological flexibility which facilitates adaptation to a wide range of host niches. In addition, formation of biofilms provides additional protection from adverse environmental conditions. Furthermore, in many host niches Candida cells coexist with members of the human microbiome. The resulting fungal-bacterial interactions have a major influence on the success of C. albicans as commensal and also influence disease development and outcome. In this chapter, we review the current knowledge of important survival strategies of Candida spp., focusing on fundamental fitness and virulence traits of C. albicans. Copyright © 2015 Elsevier Inc. All rights reserved.

  18. Psychology and survival.

    Science.gov (United States)

    Phillips, D P; Ruth, T E; Wagner, L M

    1993-11-06

    We examined the deaths of 28,169 adult Chinese-Americans, and 412,632 randomly selected, matched controls coded "white" on the death certificate. Chinese-Americans, but not whites, die significantly earlier than normal (1.3-4.9 yr) if they have a combination of disease and birthyear which Chinese astrology and medicine consider ill-fated. The more strongly a group is attached to Chinese traditions, the more years of life are lost. Our results hold for nearly all major causes of death studied. The reduction in survival cannot be completely explained by a change in the behaviour of the Chinese patient, doctor, or death-registrar, but seems to result at least partly from psychosomatic processes.

  19. Craft-Joule Project: Stagnation proof transparently insulated flat plate solar collector (static)

    Energy Technology Data Exchange (ETDEWEB)

    Oliva, A; Cadafalch, J; Perez-Segarra, C.D. [Universitat Politecnica de Catalunya, Barcelona (Spain)] (and others)

    2000-07-01

    The STATIC (STAgnation proof Transparently Insulated flat plate Solar Collector) project is a Craft-Joule Project within the framework of the Non Nuclear Energy Programme Joule III coordinated by the Centre Technologic de Transferencia de Calor (CTTC). The core group of SMEs involved in the project has its main economical activity in the field of solar thermal systems at low temperature level (domestic hot water, solar heating, etc.). Beyond this, a large application potential exists for solar heating at medium temperature level (from 80 to 160 Celsius degrees) : industrial process heat, solar cooling and air conditioning, solar drying , distillation and desalination. Three of the four SME proposers are located in Southern Europe and in the Caribean, where a continuos increase of the demand for air conditioning and cooling has been demonstrated in the last years. The recent development of flat plate solar collectors with honeycomb-type transparent insulation cover has shown that this type of collectors can become a low cost alternative to evacuated tube and high concentrating CPC collectors in the medium temperature range from 80 to 160 Celsius degrees. With the expected reduction of collector cost, that forms 30%-50% of total system cost, a decisive break-through of solar thermal systems using heat in the medium temperature range can be achieved. The feasibility and good performance of these solar collectors has been proved in several prototypes. Nevertheless, up to now no commercial products are available. In order to reach this, the following developments of new concepts are necessary and are being carried out within this project: solution of the problem of overheating: development of collector versions for different working temperatures: optimization of the design with the support of high level numerical simulation. Several prototypes of the new solar collectors are being tested. System tests will also be carried or for two test arrays of optimized collector

  20. Survival assays using Caenorhabditis elegans.

    Science.gov (United States)

    Park, Hae-Eun H; Jung, Yoonji; Lee, Seung-Jae V

    2017-02-01

    Caenorhabditis elegans is an important model organism with many useful features, including rapid development and aging, easy cultivation, and genetic tractability. Survival assays using C. elegans are powerful methods for studying physiological processes. In this review, we describe diverse types of C. elegans survival assays and discuss the aims, uses, and advantages of specific assays. C. elegans survival assays have played key roles in identifying novel genetic factors that regulate many aspects of animal physiology, such as aging and lifespan, stress response, and immunity against pathogens. Because many genetic factors discovered using C. elegans are evolutionarily conserved, survival assays can provide insights into mechanisms underlying physiological processes in mammals, including humans.

  1. Surviving a Suicide Attempt

    Directory of Open Access Journals (Sweden)

    Ahmed Al-Harrasi

    2016-09-01

    Full Text Available Suicide is a global phenomenon in all regions of the world affecting people of all age groups. It has detrimental consequences on patients, their families, and the community as a whole. There have been numerous risk factors described for suicide including mental illness, stressful life situations, loss of social support, and general despair. The association of suicide with Islam has not been extensively studied. The common impression from clinical practice is that being a practicing Muslim reduces the risk of suicide. Another factor associated with suicide is starting a patient on antidepressants. However, this has been questioned recently. This report describes a middle-aged man with depression and multiple social stressors who survived a serious suicide attempt. The discussion will focus on the factors that lead him to want to end his life and the impact of the assumed protective factors such as religious belief and family support on this act of self-harm. Such patients can be on the edge when there is an imbalance between risk factors (such as depression, insomnia, and psychosocial stressors and protective factors (like religious affiliation and family support. All physicians are advised to assess the suicide risk thoroughly in patients with depression regardless of any presumed protective factor.

  2. Surviving a Suicide Attempt.

    Science.gov (United States)

    Al-Harrasi, Ahmed; Al Maqbali, Mandhar; Al-Sinawi, Hamed

    2016-09-01

    Suicide is a global phenomenon in all regions of the world affecting people of all age groups. It has detrimental consequences on patients, their families, and the community as a whole. There have been numerous risk factors described for suicide including mental illness, stressful life situations, loss of social support, and general despair. The association of suicide with Islam has not been extensively studied. The common impression from clinical practice is that being a practicing Muslim reduces the risk of suicide. Another factor associated with suicide is starting a patient on antidepressants. However, this has been questioned recently. This report describes a middle-aged man with depression and multiple social stressors who survived a serious suicide attempt. The discussion will focus on the factors that lead him to want to end his life and the impact of the assumed protective factors such as religious belief and family support on this act of self-harm. Such patients can be on the edge when there is an imbalance between risk factors (such as depression, insomnia, and psychosocial stressors) and protective factors (like religious affiliation and family support). All physicians are advised to assess the suicide risk thoroughly in patients with depression regardless of any presumed protective factor.

  3. Will the olympics survive?.

    Science.gov (United States)

    Khosla, T.

    1977-01-01

    The United States of America dominated 58 events in athletics, field and swimming, which between them accounted for 35 per cent of all events in the Munich Olympiad. 1972; these events favour taller individuals. But, in 25 per cent of other events (1) cycling, (2) fencing, (3) gymnastics, (4) judo, (5) weightlifting and (6) Graeco Roman wrestling the U.S.A. did not win a single medal. The failure of the U.S.A. to maintain her lead in Munich was largely due to weaknesses in these other events in many of which the potential medallists can be derived from the lower half of the height distribution (events 3 to 6). These weaknesses are Russia's strength and they continued to remain unstrengthened at Montreal. Also, the domination held by the U.S.A. in swimming was seriously challenged by East Germany. The present trends indicate that the U.S.A.'s ranking is likely to slip further to the third position in Moscow 1980. Factors inhibiting the survival of the Olympics are pointed. PMID:861436

  4. Survival After Relapse of Medulloblastoma.

    Science.gov (United States)

    Koschmann, Carl; Bloom, Karina; Upadhyaya, Santhosh; Geyer, J Russell; Leary, Sarah E S

    2016-05-01

    Survival after recurrence of medulloblastoma has not been reported in an unselected cohort of patients in the contemporary era. We reviewed 55 patients diagnosed with medulloblastoma between 2000 and 2010, and treated at Seattle Children's Hospital to evaluate patterns of relapse treatment and survival. Fourteen of 47 patients (30%) over the age of 3 experienced recurrent or progressive medulloblastoma after standard therapy. The median time from diagnosis to recurrence was 18.0 months (range, 3.6 to 62.6 mo), and site of recurrence was metastatic in 86%. The median survival after relapse was 10.3 months (range, 1.3 to 80.5 mo); 3-year survival after relapse was 18%. There were trend associations between longer survival and having received additional chemotherapy (median survival 12.8 vs. 1.3 mo, P=0.16) and radiation therapy (15.4 vs. 5.9 mo, P=0.20). Isolated local relapse was significantly associated with shorter survival (1.3 vs. 12.8 mo, P=0.009). Recurrence of medulloblastoma is more likely to be metastatic than reported in previous eras. Within the limits of our small sample, our data suggest a potential survival benefit from retreatment with cytotoxic chemotherapy and radiation even in heavily pretreated patients. This report serves as a baseline against which to evaluate novel therapy combinations.

  5. Transformation Craft (T-Craft) Concept Study

    Science.gov (United States)

    2007-08-01

    reduction, it was later determined that fiberglass tanks are needed to meet stability criteria. The same type of pillow tank was also evaluated for gray...system. However, it uses 5% chlorine solution as a disinfectant , thus requiring the need to carry additional chemicals onboard. The Super Trident...Technology, Economics, and Applications. Amsterdam: Elsevier Science Publishers, 1989. iiArrington, Jess W. Naval Post Graduate School. The

  6. Design Method for Contra-Rotating Propellers for High-Speed Crafts: Revising the Original Lerbs Theory in a Modern Perspective

    Directory of Open Access Journals (Sweden)

    Stefano Brizzolara

    2012-01-01

    Full Text Available The main theoretical and numerical aspects of a design method for optimum contrar-rotating (CR propellers for fast marine crafts are presented. We propose a reformulated version of a well-known design theory for contra-rotating propellers, by taking advantage of a new fully numerical algorithm for the calculation of the mutually induced velocities and introducing new features such as numerical lifting surface corrections, use of an integrated modern cavitation/strength criteria, a modified method to consider different numbers of blades among the two propellers, and to allow for an unloading function in the search for the optimal circulation distribution. The paper first introduces the main theoretical principles of the new methods and then discusses the influence of the main design parameters on an emblematic example of application in the case of counter rotating propellers for a pod propulsor designed for fast planing crafts (35 knots and above.

  7. “The Great Palace of American Civilization”: Allen Eaton’s Arts and Crafts of the Homelands, 1919-1932

    Directory of Open Access Journals (Sweden)

    Diana Greenwold

    2014-06-01

    Full Text Available Allen Eaton’s Arts and Crafts of the Homelands exhibition premiered in Buffalo, New York in 1919, where it drew record crowds to the Albright Gallery. Iterations of the display soon opened in Albany, Rochester, and then in several other cities across the United States. Arts and Crafts of the Homelands showcased European craftwork of local immigrant groups to celebrate a model of early twentieth-century American pluralism. This article examines the aims of exhibit organizers, immigrant presenters, and native-born visitors to these exhibitions. The structure of the displays—which highlighted domestic tableaux of old-world objects—obfuscated the contemporary contributions of immigrant groups to American cultural and economic forums. I argue, however, that local groups took advantage of the exhibit’s performance spaces to assert their active presence in American public life. 

  8. Methanetrisulfonic Acid: A Highly Efficient Strongly Acidic Catalyst for Wagner-Meerwein Rearrangement, Friedel-Crafts Alkylation and Acylation Reactions. Examples from Vitamin E Synthesis

    Directory of Open Access Journals (Sweden)

    Francesco Pace

    2009-04-01

    Full Text Available Methanetrisulfonic acid had been prepared for the first time over 140 years ago, but it was used only scarcely in chemical transformations. In the course of our activities dealing with key-steps of industrial syntheses of vitamins, e.g. economically important vitamin E (acetate, we found that methanetrisulfonic acid is an extremely effective catalyst in a variety of reactions. Examples of its applications are Wagner-Meerwein rearrangements, Friedel-Crafts alkylations and ring closures, as well as acylation reactions. Use of this catalyst in truly catalytic amounts (0.04-1.0 mol% resulted in highly selective transformations and yields over 95%. (Remark by the authors: We are describing only one example each for the various types of reactions. Therefore, it would be more appropriate to write (here and in the Introduction and in the Conclusion sections: “Wagner-Meerwein rearrangement, Friedel-Crafts alkylation and ring closure, as well as acylation reactions”

  9. Marketing child survival.

    Science.gov (United States)

    Grant, J P

    1984-01-01

    Growth monitoring charts, packets of oral rehydration salts (ORS), and vaccines, are inexpensive, life-saving, growth-protecting technologies which can enable parents to protect their children against the worst effects of poverty. Similarly, a matrix of current and easily understandable information about pregnancy, breast feeding, weaning, feeding during and immediately after illness, child spacing, and preparing and using home-made oral rehydration solutions, also could empower parents to protect the lives and the health of their children. The question arises as to how can these technologies and this information be put at the disposal of millions of families in the low-income world. The initial task of the Child Survival and Development Revolution is the communication of what is now possible, yet little is known about how to communicate information whose principal value is to the poor. There are 2 large-scale precedents: the Green Revolution, which in many instances succeeded in putting into the hands of thousands of small and large farmers the techniques and the knowledge which enabled them to double and treble the yields from their lands; and the campaign to put the knowledge and the means of family planning at the disposal of many millions of people. There are 2 lessons to be learned from these precedents: they have shown that the way to promote a people's technology and to put information at the disposal of the majority is by mobilizing all possible resources and working through all possible channels both to create the demand and to meet it; and neither the Green Revolution nor the family planning movement rally took off until they were viewed as political and economic priorities and given the full support of the nation's political leadership. Nowhere are these 2 lessons more clearly illustrated than in present-day Indonesia. Because the campaign for family planning was given high personal and political priority by the President, and because 85% of all family

  10. Gode Valg – om læreres utvelgelseskompetanse i Kunst og håndverk (Good choices – on teachers’ selection competence in Arts and Crafts

    Directory of Open Access Journals (Sweden)

    Marte Sørebø Gulliksen

    2013-01-01

    Full Text Available The article highlights and discusses teachers’ educational selection competence in the subject area of Arts and Crafts, and introduces the assumption that it is possible and useful to construct a choice perspective on educational actions. Certain challenges related to the requirements of the teachers’ selection competence, such as teachers’ knowledge, pedagogical content knowledge, content, methods and assessment of the subject, are also introduced. Vygotskij’s theories on borrowed experiences, and the psychological judgement theories of Kahneman & Tversky and Kahneman & Fredricks, are presented as selected theoretical perspectives. Examples from empirical studies that have focused on the specialized area of teacher education in Arts and Crafts are also provided. Situations in which selection issues are critical to a student’s learning and mastery of the upcoming profession are presented and discussed. The choice perspective reveals a potential opportunity to develop new structures in the complex situation of Arts and Crafts teacher education. The perspective may shed light on how uncertainty led participants to restrict their choices to those that were perceived as viable options. Moreover, it could help to problematize aspects of the speciality of this area of teacher education, and more specifically, the combination of creative praxis in arts, design and/or crafts, and educational practice and teaching skills. It is concluded that more research is needed, and it is hoped that on-going research will be facilitated to contribute to this initial study. This knowledge will strengthen the research-based foundation for educating teachers with enough selection competence to make sound choices.

  11. [Health, illnes and higiene in the boarding schools. the case of the salesian arts and craft scholl of Córdoba. 1905 - 1930].

    Science.gov (United States)

    Moretti, Nicolás

    2017-01-01

    The following article asks about the speeches, practices, representations and experiences on health, hygiene and illnes in boarding schools early last century, taking for instance the School of Arts and Crafts of the Salesian Congregation, with the intention of revisiting the dialogue between medicine, hygiene and school in the context of development of the social question, the result of accelerated modernization process experienced by the city of Córdoba.

  12. Stereocontrolled syntheses of tetralone- and naphthyl-type lignans by a one-pot oxidative [3,3] rearrangement/Friedel-Crafts arylation.

    Science.gov (United States)

    Reddel, Jordan C T; Lutz, Kelly E; Diagne, Abdallah B; Thomson, Regan J

    2014-01-27

    The development of a stereoselective one-pot oxidative [3,3] sigmatropic rearrangement/Friedel-Crafts arylation that provides enantioenriched benzhydryl compounds is reported. The utility of this new transformation is demonstrated by the concise synthesis of several tetralone- and naphthyl-type lignan natural products, many of which display anti-malarial activity. Copyright © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  13. From the History of Lace Craft in the South Black Earth Russia (2nd Half of the 19th Century - Beginning of the 20th Century

    Directory of Open Access Journals (Sweden)

    Grigorova Viktoriya A.

    2016-10-01

    Full Text Available The author studies the specifics of lace in the territory of the South Black Earth Russia in the 19th – early 20th centuries. The author has analyzed the history of lace crafts in the Yelets and Mtsensk districts of the Orlovsk province, and in the Zadonsk district of the Voronezh province. Based on archive materials the article determines such features of lace crafts development as the uniqueness of lace; the dependence of the growth of the influence of buyers on the pace of industry development; presence of the qualitative indicators of the manufacturing process inversely proportional to the quantitative; expanding the range of manufactured lace; the expansion of the sales area of lace; activation of the attention of individuals and public institutions to revive the specificity and individuality of local products lace. It was concluded that the impact of identified features on the pace of development of the lace industry in the South Black Earth Russia and on the development of Russian business in general. Analyzing the history of lace crafts, the author describes the conditions of industrial activity lace, which showed the formation of the capitalist forms of lace makers’ work. The features of the capitalist forms of labour which characterized crafts activity are pointed out. The peculiarities of lace sales organization in local and distant markets are studied. In addition to interprovince and interdistrict markets the author investigates the material on exporting goods abroad. The main reasons for the expansion of sales geography determine the change in product mix. The author raises the issue related to the history of the preservation of unique lace made following the traditions of Russian folk art of their ancestors. The problem consisted in the fact that the buyers were not interested in the originality and identity of the goods. As a result, this led to the reduction of the original performance by increasing the amount of work on the

  14. Wetland craft plants in KwaZulu-Natal: an ecological review of har­vesting impacts and implications for sustainable utilization

    Directory of Open Access Journals (Sweden)

    C. H. Traynor

    2010-07-01

    Full Text Available In South Africa, wetland plants have been used for centuries and they continue to be harvested for subsistence and commercial purposes. Fibres for crafts are collected by cutting the aboveground parts. KwaZulu-Natal is one of the major basket-producing regions in southern Africa and at least twenty-two species of wetland plants are harvested for crafts. A literature review of the harvested species revealed that the impacts of cutting have only been extensively investigated for Phragmites australis (Cav. Steud. and Juncus kraussii Hochst. The review suggested that, where plants display strong seasonal aboveground productivity patterns, cutting should take place after shoot senescence and before new shoot emergence to minimize damage to plants. Cutting in the short term could increase the density of green stems. However, in the long term in  Phragmites australis, it may deplete the rhizome reserves and reduce the density of useable (longer and thicker culms.The opportunity for sustainable harvests was investigated by considering the geographic distribution, whether species are habitat specific or not, and local population sizes of the craft plants. Juncus kraussii is of the greatest conservation concern.Ecologically sustainable wetland plant harv esting could contribute to the wise use of wetlands, an approach promoted nationally and internationally.

  15. The effects of a combined physical activity, recreation, and art and craft program on ADL, cognition, and depression in the elderly.

    Science.gov (United States)

    Kim, DeokJu

    2017-04-01

    [Purpose] To determine the effects of a combined physical activity, arts and crafts, and recreational program on the activities of daily living (ADL), cognitive function, and depression in the elderly. [Subjects and Methods] Twenty-eight elderly persons aged 65 years or older who live in P City, South Korea participated in a program combining arts and crafts and physical and recreational activities, twice weekly for eight weeks (a total of 16 sessions). The subjects' ADL, cognitive function, and depression were measured before and after the program using the following assessment instruments: the FIM, MMSE-K, and BDI, respectively. [Results] The results showed that, after the program intervention, ADL were remarkably improved for both men and women, cognitive function increased considerably, and depression levels significantly decreased, especially for elderly women. [Conclusion] The results of the present study indicate that a program combining physical and recreational activities, as well as arts and crafts, had positive effects on the health of the elderly and provide evidence for managing their health.

  16. Wetland craft plants in KwaZulu-Natal: an ecological review of har­vesting impacts and implications for sustainable utilization

    Directory of Open Access Journals (Sweden)

    C. H. Traynor

    2010-12-01

    Full Text Available In South Africa, wetland plants have been used for centuries and they continue to be harvested for subsistence and commercial purposes. Fibres for crafts are collected by cutting the aboveground parts. KwaZulu-Natal is one of the major basket-producing regions in southern Africa and at least twenty-two species of wetland plants are harvested for crafts. A literature review of the harvested species revealed that the impacts of cutting have only been extensively investigated for Phragmites australis (Cav. Steud. and Juncus kraussii Hochst. The review suggested that, where plants display strong seasonal aboveground productivity patterns, cutting should take place after shoot senescence and before new shoot emergence to minimize damage to plants. Cutting in the short term could increase the density of green stems. However, in the long term in  Phragmites australis, it may deplete the rhizome reserves and reduce the density of useable (longer and thicker culms.The opportunity for sustainable harvests was investigated by considering the geographic distribution, whether species are habitat specific or not, and local population sizes of the craft plants. Juncus kraussii is of the greatest conservation concern.Ecologically sustainable wetland plant harv esting could contribute to the wise use of wetlands, an approach promoted nationally and internationally.

  17. [Simplified models of analysis of the sources of risk and biomechanical overload in craft industries: application experience in wooden barrel making].

    Science.gov (United States)

    Pressiani, Sofia

    2011-01-01

    Barrel making is an ancient art evidence of which is found in paintings from the Egyptian era in the Mediterranean civilizations, and since it was an ideal shipping container its use spread quickly and on a wide scale. The study was conducted in a small high quality craft industry, applying the method which is the topic of this volume, i.e., risk pre-mapping by which it is possible to identify the presence or absence of occupational risk and any need for further evaluation. The study showed the presence of health risks for workers, which were mainly physical (noise, vibrations produced by machinery and equipment typical of the craft, and risks from hardwood dust, in addition to the traditional risks of biomechanical overload of the upper limbs. Today, the barrel maker is a professional craft of excellence and quality, dedicated to the creation of large barrels and vats, using woods of different essences depending on the organoleptic qualities that it is desired should influence the final flavour of the wine: the manual art and the equipment are ancient but the technology used to achieve the final product is necessarily advanced. So far issues of safety and health risks related to this type of industry have received little attention and the risks poorly evaluated, with the possibility that occupational diseases may occur among the operators, particularly of the skeletal-muscular type.

  18. Synthesis of Chiral TFA-Protected α-Amino Aryl-Ketone Derivatives with Friedel–Crafts Acylation of α-Amino Acid N-Hydroxysuccinimide Ester

    Directory of Open Access Journals (Sweden)

    Zetryana Puteri Tachrim

    2017-10-01

    Full Text Available Chiral N-protected α-amino aryl-ketones are one of the useful precursors used in the synthesis of various biologically active compounds and can be constructed via Friedel–Crafts acylation of N-protected α-amino acids. One of the drawbacks of this reaction is the utilization of toxic, corrosive and moisture-sensitive acylating reagents. In peptide construction via amide bond formation, N-hydroxysuccinimide ester (OSu, which has high storage stability, can react rapidly with amino components and produces fewer side reactions, including racemization. This study reports the first synthesis and utilization of N-trifluoroacetyl (TFA-protected α-amino acid-OSu as a potential acyl donor for Friedel–Crafts acylation into various arenes. The TFA-protected isoleucine derivative and its diastereomer TFA-protected allo-isoleucine derivative were investigated to check the retention of α-proton chirality in the Friedel–Crafts reaction. Further utilization of OSu in other branched-chain and unbranched-chain amino acids results in an adequate yield of TFA-protected α-amino aryl-ketone without loss of optical purity.

  19. Global Activities and Plant Survival

    DEFF Research Database (Denmark)

    Bandick, Roger

    2014-01-01

    This chapter provides an extensive review of the empirical evidence found for Sweden concerning plant survival. The result reveals that foreign MNE plants and exporting non-MNE plants have the lowest exit rates, followed by purely domestic-oriented plants, and that domestic MNE plants have...... the highest exit rates. Moreover, the exit rates of globally engaged plants seem to be unaffected by increased foreign presence, whereas there appears to be a negative impact on the survival rates of non-exporting non-MNE plants. Finally, the result reveals that the survival ratio of plants of acquired...... exporters, but not other types of plants, improves post acquisition....

  20. Cardiovascular disease incidence and survival

    DEFF Research Database (Denmark)

    Byberg, Stine; Agyemang, Charles; Zwisler, Ann Dorthe

    2016-01-01

    Studies on cardiovascular disease (CVD) incidence and survival show varying results between different ethnic groups. Our aim was to add a new dimension by exploring the role of migrant status in combination with ethnic background on incidence of-and survival from-CVD and more specifically acute...... of some types of cardiovascular disease compared to Danish-born. Family-reunified migrants on the other hand had lower rates of CVD. All migrants had better survival than Danish-born indicating that migrants may not always be disadvantaged in health....

  1. Crafting semiconductor organic-inorganic nanocomposites via placing conjugated polymers in intimate contact with nanocrystals for hybrid solar cells.

    Science.gov (United States)

    Zhao, Lei; Lin, Zhiqun

    2012-08-22

    Semiconductor organic-inorganic hybrid solar cells incorporating conjugated polymers (CPs) and nanocrystals (NCs) offer the potential to deliver efficient energy conversion with low-cost fabrication. The CP-based photovoltaic devices are complimented by an extensive set of advantageous characteristics from CPs and NCs, such as lightweight, flexibility, and solution-processability of CPs, combined with high electron mobility and size-dependent optical properties of NCs. Recent research has witnessed rapid advances in an emerging field of directly tethering CPs on the NC surface to yield an intimately contacted CP-NC nanocomposite possessing a well-defined interface that markedly promotes the dispersion of NCs within the CP matrix, facilitates the photoinduced charge transfer between these two semiconductor components, and provides an effective platform for studying the interfacial charge separation and transport. In this Review, we aim to highlight the recent developments in CP-NC nanocomposite materials, critically examine the viable preparative strategies geared to craft intimate CP-NC nanocomposites and their photovoltaic performance in hybrid solar cells, and finally provide an outlook for future directions of this extraordinarily rich field. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  2. [Physical activity and cancer survival].

    Science.gov (United States)

    Romieu, Isabelle; Touillaud, Marina; Ferrari, Pietro; Bignon, Yves-Jean; Antoun, Sami; Berthouze-Aranda, Sophie; Bachmann, Patrick; Duclos, Martine; Ninot, Grégory; Romieu, Gilles; Sénesse, Pierre; Behrendt, Jan; Balosso, Jacques; Pavic, Michel; Kerbrat, Pierre; Serin, Daniel; Trédan, Olivier; Fervers, Béatrice

    2012-10-01

    Physical activity has been shown in large cohort studies to positively impact survival in cancer survivors. Existing randomized controlled trials showed a beneficial effect of physical activity on physical fitness, quality of life, anxiety and self-esteem; however, the small sample size, the short follow-up and the lack of standardization of physical activity intervention across studies impaired definite conclusion in terms of survival. Physical activity reduces adiposity and circulating estrogen levels and increases insulin sensitivity among other effects. A workshop was conducted at the International Agency for Research on Cancer in April 2011 to discuss the role of physical activity on cancer survival and the methodology to develop multicentre randomized intervention trials, including the type of physical activity to implement and its association with nutritional recommendations. The authors discuss the beneficial effect of physical activity on cancer survival with a main focus on breast cancer and report the conclusions from this workshop.

  3. Operational slack and venture survival

    OpenAIRE

    Azadegan, Arash; Patel, Pankaj; Parida, Vinit

    2013-01-01

    Slack can act as a double-edged sword. While it can buffer against environmental threats to help ensure business continuity, slack canalso be costly and reduce profitability. In this study, we focus on operational slack, the form related to the firm’s production processes. We investigate the role of operational slack on firm survival during its venture stage, when its survival is significantly challenged by environmental threats. Specifically, we explore how change in three types of environme...

  4. A framework for crafting and implementing a congregational strategy in the local congregations of the Reformed Churches of South Africa

    Directory of Open Access Journals (Sweden)

    Aldeon B. Grobler

    2012-11-01

    Full Text Available The church is not like any other institution or organisation in society. Although the church is primarily invisible and spiritual, it is a visible organisation in the world, and it spans across borders of nations, languages and countries. John Calvin strongly rejected the notion that the church is only a spiritual organisation of which the visible administrative side is downplayed. The fellowship of the church must not only be seen as a mystical relation with Jesus Christ. During 2010, an empirical study was done on the extent to which congregations of the Reformed Churches of South Africa (RCSA adhere to the request to have a well-designed congregational strategy. The knowledge gained from a literature study on the science of Strategic Management and the results of the empirical study was combined into a framework for crafting and executing a congregational strategy. This framework can be used by congregational leaders to guide them through their own process of crafting and executing their unique congregational strategy.  The research was concluded with a recommendation that the Theological School of the RCSA should consider including a course on Strategic Management in the training syllabus of aspiring ministers. Considering that Strategic Management is a specialised management science, and external Strategic Management consultants tend to be expensive, the research also recommended that the Administrative Bureau of the RCSA consider employing their own Strategic Management consultant for the RCSA with the specific assignment of assisting and guiding all congregations with their congregational strategy.’n Raamwerk vir die ontwerp en implementering van ’n gemeentestrategie in die plaaslike gemeentes van die Gereformeerde Kerke in Suid-Afrika. ’n Kerk is ’n unieke organisasie. Die kerk is primêr onsigbaar en geestelik van  aard. Tog  funksioneer dit as ’n instituut in die wêreld en moet dit doelmatig en doeltreffend bestuur word

  5. „Sirogojno Style“: The Production and Distribution of Hand-crafted Objects/Products Made of Wool

    Directory of Open Access Journals (Sweden)

    Senka Kovač

    2016-03-01

    Full Text Available The basic premise of my research regarding the fashion production of Sirogojno style was that „objects are, like words, carriers of information“. Based on research published so far – a paper by Bojana Bogdanovic being the most detailed – and my own fieldwork conducted in 2010, I have attempted to ascertain the extent to which this particular style of fashion carried information about the cultural environment which it represented. The research encompasses the study of the materials being used, the production and the sale of products made of wool. The development of this particular style was influenced by the enthusiasm of designer Dobrila Vasiljevic-Smiljanic and the women of the mt. Zlatibor region, as well as the support provided by the political structure of the period, the local government, and through Dobrila Vasiljevic-Smiljanic’s family ties – the church. Her creations are famous for incorporating adapted local ornaments. A distinct and recognizable style of woolen products was created. This „Wool Road“ – from using local raw materials to materials imported from Iceland, from creating unique motifs to sale in the open, from national and international sales to musealized sales in the first decade of the 21st century – has lasted for over fifty years. Products from Sirogojno were renowned both in the country and abroad. All the negative processes which happened during the nineties influenced the decline of production and distribution of hand-crafted products from Sirogojno. In the late 1990’s, the production was acquired by a local owner who didn’t show much interest in it. This production has been musealized in the first decade of the 21st century. Dobrila Vasiljevic-Smiljanic told me in 2010 that „everything should be started from scratch now, from new motifs to new marketing“. The new owners of the firm say that „the villages are deserted and there aren’t enough weavers“. On the other hand, there is sale

  6. 'Al pie de la letra': crafting a report card for elderly Spanish-only-speaking patients with stroke.

    Science.gov (United States)

    Ovbiagele, Bruce

    2010-04-01

    Ethnic minorities are at higher stroke risk than non-Hispanic whites yet are less likely to have optimal vascular risk factor control. There is a need to develop culturally sensitive strategies for enhancing vascular risk reduction in minority patients with stroke. This study aimed to develop a postdischarge report card to boost treatment adherence among elderly Spanish-speaking patients with stroke within an urban health system. This study included a total of 13 Spanish-only speaking participants aged > or = 60 years discharged from a local government hospital in Los Angeles within 18 months of an index ischemic stroke and 6 caregivers engaged in focus groups and interviews. Structured interviews were conducted with 11 care providers and 9 administrators at the hospital. Framework analysis examined the data and elicited themes to adapt a pre-existing patient report card tool. Spontaneously using the same phrase, "Al pie de la letra," several participants expressed a need to follow medical instructions accurately to prevent recurrent stroke and identified barriers/facilitators for doing so. They made comments about the pre-existing report card, advising several changes, including the clarification of phrases, and written instructions to explain the need for the card and how to fill it out. The providers and administrators recommended avenues for successfully using the card at the hospital. A new report card was created that incorporated all major perspectives. Crafting a culturally sensitive tool for promoting treatment adherence in elderly Spanish-only-speaking patients with stroke within an urban health system using a participatory methodology is feasible. The efficacy of this new report card should be tested in a randomized controlled trial.

  7. A study on the industrialization of building stones and industrial stone crafts - Study on the causes of stone contaminations

    Energy Technology Data Exchange (ETDEWEB)

    Hyun, Jeon Ki; Lee, Han Yeang [Korea Institute of Geology Mining and Materials, Taejon (Korea, Republic of)

    1996-12-01

    Causes of building stone contamination are acid rains in polluted areas, iron bearing minerals in stone itself, salts, sealants, cutting and grinding processes in stone factory and steel compounds structures such as stone anchors, bolts, rain culvert and guide frames. Contaminations on the building stone surface of Sejong culture center can be found around floor stones, stair stones, parterre stones, pillar stones and other outdoor stone panels. The parterre stones are contaminated by white tarnishes and rust flows are occurred on the surface of pillar stones and outdoor stone panels around entrance. Black tarnishes are cumulated on the pillar stones and other outdoor decorated stone panels and change the original granite color. Causes of building stone contaminations from Sejong culture center are wet method to attach stone panels, rust from steel compounds structures and air pollutants. Cement and mortar used from wet method react with sulfur dioxides in polluted air and from fine calcite crystals (white tarnish). Rusts from steel compounds structures such as rainwater culvert and steel guide frames can move to the stone surface by rain and leave rust flows on it. Pollutants (tar compounds, carbons, dusts, etc.) in air are cumulated with humidity on the stone surface and change color from white granite color to dusty dark color. Historical stone sculptures such as man and animal shaped stone crafts, tombstones, square stone tables in front of a tomb and guide and circumference stones around tomb in Royal Tombs (Donggu rung, Yung rung, Seoou rung and Hunin rung) distributed in Kyunggi province are contaminated by various moss and air pollutants and its original colors are deeply changed. (author). 21 refs., 11 tabs., 22 figs.

  8. Survival Processing Eliminates Collaborative Inhibition.

    Science.gov (United States)

    Reysen, Matthew B; Bliss, Heather; Baker, Melissa A

    2017-04-11

    The present experiments examined the effect of processing words for their survival value, relevance to moving, and pleasantness on participants' free recall scores in both nominal groups (non-redundant pooled individual scores) and collaborative dyads. Overall, participants recalled more words in the survival processing conditions than in the moving and pleasantness processing conditions. Furthermore, nominal groups in both the pleasantness condition (Experiment 1) and the moving and pleasantness conditions (Experiment 2) recalled more words than collaborative groups, thereby replicating the oft-observed effect of collaborative inhibition. However, processing words for their survival value appeared to eliminate the deleterious effects of collaborative remembering in both Experiments 1 and 2. These results are discussed in the context of the retrieval strategy disruption hypothesis and the effects of both expertise and collaborative skill on group remembering.

  9. Survival in Women with NSCLC

    Science.gov (United States)

    Katcoff, Hannah; Wenzlaff, Angela S.; Schwartz, Ann G.

    2014-01-01

    Introduction Although lung cancer is the leading cause of cancer death in women, few studies have investigated the hormonal influence on survival after a lung cancer diagnosis and results have been inconsistent. We evaluated the role of reproductive and hormonal factors in predicting overall survival in women with non–small-cell lung cancer (NSCLC). Methods Population-based lung cancer cases diagnosed between November 1, 2001 and October 31, 2005 were identified through the Metropolitan Detroit Surveillance, Epidemiology, and End Results Registry. Interview and follow-up data were collected for 485 women. Cox proportional hazard regression models were used to determine hazard ratios (HRs) for death after an NSCLC diagnosis associated with reproductive and hormonal variables. Results Use of hormone therapy (HT) was associated with improved survival (HR, 0.69; 95% confidence interval, 0.54–0.89), adjusting for stage, surgery, radiation, education level, pack-years of smoking, age at diagnosis, race, and a multiplicative interaction between stage and radiation. No other reproductive or hormonal factor was associated with survival after an NSCLC diagnosis. Increased duration of HT use before the lung cancer diagnosis (132 months or longer) was associated with improved survival (HR, 0.54; 95% confidence interval, 0.37–0.78), and this finding remained significant in women taking either estrogen alone or progesterone plus estrogen, never smokers, and smokers. Conclusion These findings suggest that HT use, in particular use of estrogen plus progesterone, and long-term HT use are associated with improved survival of NSCLC. PMID:24496005

  10. Survival of Sami cancer patients

    Directory of Open Access Journals (Sweden)

    Leena Soininen

    2012-07-01

    Full Text Available Objectives. The incidence of cancer among the indigenous Sami people of Northern Finland is lower than among the Finnish general population. The survival of Sami cancer patients is not known, and therefore it is the object of this study. Study design. The cohort consisted of 2,091 Sami and 4,161 non-Sami who lived on 31 December 1978 in the two Sami municipalities of Inari and Utsjoki, which are located in Northern Finland and are 300–500 km away from the nearest central hospital. The survival experience of Sami and non-Sami cancer patients diagnosed in this cohort during 1979–2009 was compared with that of the Finnish patients outside the cohort. Methods. The Sami and non-Sami cancer patients were matched to other Finnish cancer patients for gender, age and year of diagnosis and for the site of cancer. An additional matching was done for the stage at diagnosis. Cancer-specific survival analyses were made using the Kaplan–Meier method and Cox regression modelling. Results. There were 204 Sami and 391 non-Sami cancer cases in the cohort, 20,181 matched controls without matching with stage, and 7,874 stage-matched controls. In the cancer-specific analysis without stage variable, the hazard ratio for Sami was 1.05 (95% confidence interval 0.85–1.30 and for non-Sami 1.02 (0.86–1.20, indicating no difference between the survival of those groups and other patients in Finland. Likewise, when the same was done by also matching the stage, there was no difference in cancer survival. Conclusion. Long distances to medical care or Sami ethnicity have no influence on the cancer patient survival in Northern Finland.

  11. Survival following spinal cord infarction.

    Science.gov (United States)

    New, P W; McFarlane, C L

    2013-06-01

    Retrospective open cohort. To calculate the survival of patients with spinal cord infarction and to compare the cause of death in patients with different mechanisms of ischaemic injury. Spinal Rehabilitation Unit, Melbourne, Victoria, Australia. Consecutive admissions between 1 January 1995 and 31 December 2008 with recent onset of spinal cord infarction. Linkage to the Registry of Births, Deaths and Marriages (Victoria) was used to determine survival following discharge from in-patient rehabilitation and cause of death. A total of 44 patients were admitted (males=26, 59%), with a median age of 72 years (interquartile range (IQR) 62-79). One patient died during their in-patient rehabilitation programme. In all, 14 patients (n=14/44; 33%) died during the follow-up period. The median survival after diagnosis was 56 months (IQR 28-85) and after discharge from in-patient rehabilitation was 46 months (IQR 25-74). The 1- and 5-year mortality rates were 7.0% (n=3/43; 95% confidence interval (CI)=2.4-18.6%) and 20.9% (n=9/43; 95% CI=11.4-35.2%). There was no statistically significant difference in survival between patients with the different aetiologies of spinal cord infarction (other vs idiopathic: χ(2)=0.6, P=0.7; other vs vascular: χ(2)=1.9, P=0.3). There was no relationship between survival and gender (χ(2)=0.2, P=0.6), age (χ(2)=3.0, P=0.08), level of injury (χ(2)=0.0, P=1) or American Spinal Cord Society Impairment Scale grade of spinal cord injury (χ(2)=0.02, P=0.9). Patients with spinal cord infarction appear to have a fair survival after discharge from in-patient rehabilitation, not withstanding the occurrence of risk factors of vascular disease in many patients.

  12. Genetic aspects of piglet survival

    OpenAIRE

    Knol, E.F.

    2001-01-01

    Piglet mortality is high. In the USA nearly 20% of the piglets do not survive between late gestation and weaning; 7% of the piglets die during farrowing and some 13% are lost during lactation. These statistics from the USA are no exception to the norm. Selection for increased piglet survival, if possible, could have an important economic impact.

    Litters and sows

    Data on some 33.000 litters and some 400.000 piglets from a commercial breeding progr...

  13. Frailty Models in Survival Analysis

    CERN Document Server

    Wienke, Andreas

    2010-01-01

    The concept of frailty offers a convenient way to introduce unobserved heterogeneity and associations into models for survival data. In its simplest form, frailty is an unobserved random proportionality factor that modifies the hazard function of an individual or a group of related individuals. "Frailty Models in Survival Analysis" presents a comprehensive overview of the fundamental approaches in the area of frailty models. The book extensively explores how univariate frailty models can represent unobserved heterogeneity. It also emphasizes correlated frailty models as extensions of

  14. Chemical Composition of the Essential Oil of Bupleurum fontanesii (Apiaceae) Growing Wild in Sicily and its Activity on Microorganisms Affecting Historical Art Crafts.

    Science.gov (United States)

    Casiglia, Simona; Bruno, Maurizio; Senatore, Federica; Senatore, Felice

    2016-01-01

    Hydrodistillation of the flowers (BpFI) of and fruits (BpFr) of Bupleurumfontanesii Guss. ex Caruel gave two oils that were analyzed by GC and GC-MS. The main components were α-elemol (16.7%), caryophyllene oxide (16.4%) and heptacosane (15.9%) in BpFl, and spathulenol (16.8%), caryophylladienol I (13.2%) and α-elemol (12.8%) in BpFr. A good antimicrobial activity against several microorganisms, including Bacillus subtilis, Staphylococcus aureus, Fusarium oxysporum and Aspergillus niger, all infesting historical art craft, was also determined.

  15. Acerca de la influencia de William Morris y el movimiento Arts & Crafts en Cataluña. Primeros apuntes y algunas puntualizaciones

    OpenAIRE

    Calvera, Anna

    1997-01-01

    En considerar el desenvolupament del Modernisme i els seus origens, se citen Morris i el Moviment de les Arts & Crafts com una de les seves principals fonts d'inspiració. Si convé considerar més en detall aquesta influencia 6s perque ja no es tracta tant de demostrar la component internacionalista del Modernisme com de comprendre que podia suposar aquest influx i demostrar si era possible que tingués Iloc, i quan. El treball es proposa, en primer Iloc, resseguir I'ascendent angles mitjanc...

  16. School Leadership: Handbook for Survival.

    Science.gov (United States)

    Smith, Stuart C., Ed.; And Others

    Based on the assumption that the survival of the nation's schools and their leaders depends on these leaders having real influence over the quality of schooling, this volume draws from the work of many authorities to look at leadership from three perspectives: the person, the structure, and the skills. Chapters focusing on the person who holds the…

  17. Long-term haemodialysis survival

    DEFF Research Database (Denmark)

    Heaf, James; Nielsen, Arne Høj; Hansen, Henrik Post

    2012-01-01

    Haemodialysis (HD) treatment for end-stage renal disease bears a poor prognosis. We present a case of a patient who, apart from two transplant periods lasting 8 months in all, was treated with conventional in-centre HD three times a week and who survived for 41 years. Patients should be aware tha...

  18. Characteristics of Patients Who Survived

    NARCIS (Netherlands)

    Verlaan, Jorrit-Jan; Choi, David; Versteeg, Anne; Albert, Todd; Arts, Mark; Balabaud, Laurent; Bunger, Cody; Buchowski, Jacob Maciej; Chung, Chung Kee; Coppes, Maarten Hubert; Crockard, Hugh Alan; Depreitere, Bart; Fehlings, Michael George; Harrop, James; Kawahara, Norio; Kim, Eun Sang; Lee, Chong-Suh; Leung, Yee; Liu, Zhongjun; Martin-Benlloch, Antonio; Massicotte, Eric Maurice; Mazel, Christian; Meyer, Bernhard; Peul, Wilco; Quraishi, Nasir A.; Tokuhashi, Yasuaki; Tomita, Katsuro; Ulbricht, Christian; Wang, Michael; Oner, F. Cumhur

    2016-01-01

    Purpose Survival after metastatic cancer has improved at the cost of increased presentation with metastatic spinal disease. For patients with pathologic spinal fractures and/or spinal cord compression, surgical intervention may relieve pain and improve quality of life. Surgery is generally

  19. Genetic aspects of piglet survival

    NARCIS (Netherlands)

    Knol, E.F.

    2001-01-01

    Piglet mortality is high. In the USA nearly 20% of the piglets do not survive between late gestation and weaning; 7% of the piglets die during farrowing and some 13% are lost during lactation. These statistics from the USA are no exception to the norm. Selection for increased piglet

  20. Cool echidnas survive the fire

    Science.gov (United States)

    Nowack, Julia; Cooper, Christine Elizabeth; Geiser, Fritz

    2016-01-01

    Fires have occurred throughout history, including those associated with the meteoroid impact at the Cretaceous–Palaeogene (K–Pg) boundary that eliminated many vertebrate species. To evaluate the recent hypothesis that the survival of the K–Pg fires by ancestral mammals was dependent on their ability to use energy-conserving torpor, we studied body temperature fluctuations and activity of an egg-laying mammal, the echidna (Tachyglossus aculeatus), often considered to be a ‘living fossil’, before, during and after a prescribed burn. All but one study animal survived the fire in the prescribed burn area and echidnas remained inactive during the day(s) following the fire and substantially reduced body temperature during bouts of torpor. For weeks after the fire, all individuals remained in their original territories and compensated for changes in their habitat with a decrease in mean body temperature and activity. Our data suggest that heterothermy enables mammals to outlast the conditions during and after a fire by reducing energy expenditure, permitting periods of extended inactivity. Therefore, torpor facilitates survival in a fire-scorched landscape and consequently may have been of functional significance for mammalian survival at the K–Pg boundary. PMID:27075255

  1. Modelling survival and connectivity of

    NARCIS (Netherlands)

    van der Molen, J.; van Beek, J.; Augustine, S.; Vansteenbrugge, L.; van Walraven, L.; van Langenberg, V.; van der Veer, H.W.; Hostens, K.; Pitois, S.; Robbens, J.

    2015-01-01

    Three different models were applied to study the reproduction, survival and dispersal of Mnemiopsis leidyi in the Scheldt estuaries and the southern North Sea: a high-resolution particle tracking model with passive particles, a low-resolution particle tracking model with a reproduction model

  2. Survivability of SCADA Control Loop

    NARCIS (Netherlands)

    Camacho, José; de Boer, Pieter-Tjerk; Remke, Anne Katharina Ingrid

    2009-01-01

    The endorsement of information technologies for critical infrastructures control introduces new threats in their security and surveillance. Along with certain level of protection against attacks, it is desirable for critical processes to survive even if they succeed. A stochastic Petri Nets-based

  3. Crafting the News

    Science.gov (United States)

    Strawser, Michael G.

    2017-01-01

    Courses: This activity could be used in a basic public-speaking course to demonstrate messaging and the development of the three pillars of public speaking: content, organization, and delivery. In a basic communication course, this activity would help illustrate the process of communication (sender, receiver, feedback, channel, etc.). A mass…

  4. Crafting a Teaching Persona

    Science.gov (United States)

    Lang, James M.

    2007-01-01

    In this article, the author contemplates two books dealing with developing a teaching persona. These books are Elaine Showalter's "Teaching Literature" and Jay Parini's "The Art of Teaching". Showalter and Parini present very different perspectives on the issue. Showalter addresses it in a section called "Personae: The Teaching Self," in which she…

  5. The Craft of Editing

    DEFF Research Database (Denmark)

    Moeran, Brian

    To edit is to make a choice, or series of choices. Will I write a rough draft of this essay in longhand, or hammer it out on my computer? If the latter, what font shall I use? Times New Roman, Book Antiqua, or Garamond? Once I get started, what style shall I adopt: realistic, confessional or impr...

  6. Arctic Craft Demonstration Report

    Science.gov (United States)

    2012-11-01

    dock is the older dock which is no longer used due to shallow water and West Dock where the ACS fleet and Crowley’s ACV are located. Despite their...all participants are protected from potential hypothermia exposure, and receive adequate periods of rest and nourishment . • Slips, trips and falls

  7. Craft brewery business plan

    OpenAIRE

    García Carrillo, Javier

    2016-01-01

    Business plan The project, created with the intention of becoming a company carrying out the points described therein. Based on the readings on the subject, factories visited in Spain and in Belgium, the beers made in "Homemade" mode, attendance at specific courses and brewers events, and two years of study and observation of market developments brewer Catalan and more specifically developed in Barcelona, allow me to have a clear vision of what the public demand of this sector and the type...

  8. MineCrafting Friendship

    DEFF Research Database (Denmark)

    Skovbjerg, Helle Marie

    Based on a phenomenological inspired fieldwork of children (aged 7 to 11) playing Minecraft and producing, showing and sharing experiences through YouTube this paper explores how children engage, and relate through the activities. Focus is on sociability and playful association (Simmel, 1997......, 2013) that forms the basis for striking up friendships within the context of playing Minecraft and producing/consuming Mindcraft metatexts via YouTube. The investigation shows that children perform different types of friendships in the combination of Minecraft and Youtube. The analysis expose two...

  9. Craft Physics Interface

    OpenAIRE

    Hansson, Henrik

    2007-01-01

    This is a masters thesis (20p) in computer science at the University of Linköping. This thesis will give an introduction to what a physics engine is and what it consist of. It will put some engines under the magnifying glass and test them in a couple of runtime tests. Two cutting edge commercial physics engines have been examined, trying to predict the future of physics engines. From the research and test results, an interface for physics engine independency has been implemented for a company...

  10. Inscribing women and gender into histories and reception of design, crafts, and decorative arts of small-scale non-European cultures

    Directory of Open Access Journals (Sweden)

    Marjan Groot

    2015-06-01

    Full Text Available Given the formation of the history of art and the anthropology of material culture in the late nineteenth century, this paper focuses on the scholarly field of study which has come to consist of the interrelationship of ornament, design, craft, and decorative art. After addressing the historiography of this emerging field with special attention to non-European cultures and areas, the paper will inscribe women authors and gender into the narrative and interpretation of craft, design, decorative art, and ornament through their personal observations of small-scale societies. Examples will address Ceylon, ‘the savage woman’, Brazil, Japan, Indonesian peoples, and African peoples. Contrary to object-oriented scholarly histories of the time, women’s reflections are linked to subject-personal experiences and imply a gendered appropriation of first-hand reception. Women’s writings also offer a gendering of geography in history writing where scholarly overviews by male authors created a western historical ‘landscape’ and women’s reception of non-European cultures positioned realms beyond it.

  11. Women's experiences of increasing subjective well-being in CFS/ME through leisure-based arts and crafts activities: a qualitative study.

    Science.gov (United States)

    Reynolds, Frances; Vivat, Bella; Prior, Sarah

    2008-01-01

    To understand the meanings of art-making among a group of women living with the occupational constraints and stigma of CFS/ME. The study explored their initial motives for art-making, and then examined how art-making had subsequently influenced their subjective well-being. Ten women with CFS/ME were interviewed; three provided lengthy written accounts to the interview questions. Illness had resulted in devastating occupational and role loss. Participants took many years to make positive lifestyle changes. Art-making was typically discovered once participants had accepted the long-term nature of CFS/ME, accommodated to illness, and reprioritized occupations. Several factors then attracted participants specifically to art-making. It was perceived as manageable within the constraints of ill-health. Participants also tended to be familiar with craft skills; had family members interested in arts and crafts, and some desired a means to express grief and loss. Once established as a leisure activity, art-making increased subjective well-being mainly through providing increased satisfaction in daily life, positive self-image, hope, and contact with the outside world. Participants recommended provision of occupational/recreational counselling earlier in the illness trajectory. Creative art-making occurred as part of a broader acceptance and adjustment process to CFS/ME, and allowed some psychological escape from a circumscribed lifeworld.

  12. Novel starters for old processes: use of Saccharomyces cerevisiae strains isolated from artisanal sourdough for craft beer production at a brewery scale.

    Science.gov (United States)

    Marongiu, Antonella; Zara, Giacomo; Legras, Jean-Luc; Del Caro, Alessandra; Mascia, Ilaria; Fadda, Costantino; Budroni, Marilena

    2015-01-01

    The deliberate inoculation of yeast strains isolated from food matrices such as wine or bread, could allow the transfer of novel properties to beer. In this work, the feasibility of the use of baker's yeast strains as starters for craft beer production has been evaluated at laboratory and brewery scale. Nine out of 12 Saccharomyces cerevisiae strains isolated from artisanal sourdoughs metabolized 2 % maltose, glucose and trehalose and showed growth rates and cell populations higher than those of the brewer's strain Safbrew-S33. Analysis of allelic variation at 12 microsatellite loci clustered seven baker's strains and Safbrew-S33 in the main group of bread isolates. Chemical analyses of beers produced at a brewery scale showed significant differences among the beers produced with the baker's strain S38 or Safbrew-S33, while no significant differences were observed when S38 or the brewer's strain Safbrew-F2 was used for re-fermentation. The sensory profile of beers obtained with S38 or the brewer's yeasts did not show significant differences, thus suggesting that baker's strains of S. cerevisiae could represent a reservoir of biodiversity for the selection of starter strains for craft beer production.

  13. Individual social capital and survival

    DEFF Research Database (Denmark)

    Ejlskov, Linda; Mortensen, Rikke N; Overgaard, Charlotte

    2014-01-01

    BACKGROUND: The concept of social capital has received increasing attention as a determinant of population survival, but its significance is uncertain. We examined the importance of social capital on survival in a population study while focusing on gender differences. METHODS: We used data from...... a Danish regional health survey with a five-year follow-up period, 2007-2012 (n = 9288, 53.5% men, 46.5% women). We investigated the association between social capital and all-cause mortality, performing separate analyses on a composite measure as well as four specific dimensions of social capital while...... controlling for covariates. Analyses were performed with Cox proportional hazard models by which hazard ratios and 95% confidence intervals were calculated. RESULTS: For women, higher levels of social capital were associated with lower all-cause mortality regardless of age, socioeconomic status, health...

  14. Campylobacter virulence and survival factors.

    Science.gov (United States)

    Bolton, Declan J

    2015-06-01

    Despite over 30 years of research, campylobacteriosis is the most prevalent foodborne bacterial infection in many countries including in the European Union and the United States of America. However, relatively little is known about the virulence factors in Campylobacter or how an apparently fragile organism can survive in the food chain, often with enhanced pathogenicity. This review collates information on the virulence and survival determinants including motility, chemotaxis, adhesion, invasion, multidrug resistance, bile resistance and stress response factors. It discusses their function in transition through the food processing environment and human infection. In doing so it provides a fundamental understanding of Campylobacter, critical for improved diagnosis, surveillance and control. Copyright © 2014 Elsevier Ltd. All rights reserved.

  15. Does Intelligence Provide Survival Value?

    OpenAIRE

    Cairns, John

    2009-01-01

    Intelligence is defined as a general mental capacity to reason, plan, solve problems, think abstractly, comprehend ideas, and learn. Intelligence can also be defined as the ability to acquire and apply information gathered from the environment to modify its behavior. It is this intelligence that has allowed the genus Homo to survive for 2 million years. However, recently the global financial meltdown and the deleterious effects of climate change raise the question of whether intelligence has ...

  16. Survival on Land and Sea

    Science.gov (United States)

    1943-01-01

    flower, leaf steams, and young leaves may be eaten cooked as greens provided you cook them in several changes of water to remove the bitter taste and...and become a weed almost throughout the tropics. Its bladdery pods contain a single retl tomato-like fruit that is edible. Raspberries, blackberries ...plant that 108 SURVIVAL OK LAND AND SEA is about one foot In height and has blue flowers and inflated leaf stems. The young leaves, leafy stalks

  17. Columbia Crew Survival Investigation Report

    Science.gov (United States)

    2009-01-01

    NASA commissioned the Columbia Accident Investigation Board (CAIB) to conduct a thorough review of both the technical and the organizational causes of the loss of the Space Shuttle Columbia and her crew on February 1, 2003. The accident investigation that followed determined that a large piece of insulating foam from Columbia s external tank (ET) had come off during ascent and struck the leading edge of the left wing, causing critical damage. The damage was undetected during the mission. The CAIB's findings and recommendations were published in 2003 and are available on the web at http://caib.nasa.gov/. NASA responded to the CAIB findings and recommendations with the Space Shuttle Return to Flight Implementation Plan. Significant enhancements were made to NASA's organizational structure, technical rigor, and understanding of the flight environment. The ET was redesigned to reduce foam shedding and eliminate critical debris. In 2005, NASA succeeded in returning the space shuttle to flight. In 2010, the space shuttle will complete its mission of assembling the International Space Station and will be retired to make way for the next generation of human space flight vehicles: the Constellation Program. The Space Shuttle Program recognized the importance of capturing the lessons learned from the loss of Columbia and her crew to benefit future human exploration, particularly future vehicle design. The program commissioned the Spacecraft Crew Survival Integrated Investigation Team (SCSIIT). The SCSIIT was asked to perform a comprehensive analysis of the accident, focusing on factors and events affecting crew survival, and to develop recommendations for improving crew survival for all future human space flight vehicles. To do this, the SCSIIT investigated all elements of crew survival, including the design features, equipment, training, and procedures intended to protect the crew. This report documents the SCSIIT findings, conclusions, and recommendations.

  18. Statistical analysis of survival data.

    Science.gov (United States)

    Crowley, J; Breslow, N

    1984-01-01

    A general review of the statistical techniques that the authors feel are most important in the analysis of survival data is presented. The emphasis is on the study of the duration of time between any two events as applied to people and on the nonparametric and semiparametric models most often used in these settings. The unifying concept is the hazard function, variously known as the risk, the force of mortality, or the force of transition.

  19. LATERAL SURVIVAL: AN OT ACCOUNT

    Directory of Open Access Journals (Sweden)

    Moira Yip

    2004-12-01

    Full Text Available When laterals are the targets of phonological processes, laterality may or may not survive. In a fixed feature geometry, [lateral] should be lost if its superordinate node is eliminated by either the spreading of a neighbouring node, or by coda neutralization. So if [lateral] is under Coronal (Blevins 1994, it should be lost under Place assimilation, and if [lateral] is under Sonorant Voicing (Rice & Avery 1991 it should be lost by rules that spread voicing. Yet in some languages lateral survives such spreading intact. Facts like these argue against a universal attachment of [lateral] under either Coronal or Sonorant Voicing, and in favour of an account in terms of markedness constraints on feature-co-occurrence (Padgett 2000. The core of an OT account is that IFIDENTLAT is ranked above whatever causes neutralization, such as SHARE-F or *CODAF. laterality will survive. If these rankings are reversed, we derive languages in which laterality is lost. The other significant factor is markedness. High-ranked feature co-occurrence constraints like *LATDORSAL can block spreading from affecting laterals at all.

  20. Artesanias Mexico - Americanas. Programa Piloto de Entrenamiento Para El Asociado Bilingue y Bicultural En El Desarrollo del Nino: Guia XIII [Arts and Crafts of Mexico and the Americas. Pilot Program for the Training of Bilingual and Bicultural Teachers for the Cognitive Development of the Child: Guide XIII].

    Science.gov (United States)

    de Celis, Margarita

    This Child Development Associate (CDA) training module, the thirteenth in a series of 16, provides creative experiences with arts and crafts for young children. Designed for preschool teachers and paraprofessional trainees, the Spanish text offers a variety of craft activities. A list of materials necessary, step-by-step directions and…

  1. Stage at diagnosis and ovarian cancer survival

    DEFF Research Database (Denmark)

    Maringe, Camille; Walters, Sarah; Butler, John

    2012-01-01

    We investigate what role stage at diagnosis bears in international differences in ovarian cancer survival.......We investigate what role stage at diagnosis bears in international differences in ovarian cancer survival....

  2. Surviving to Tell the Tale: Josef Haslinger’s Phi Phi Island (2007

    Directory of Open Access Journals (Sweden)

    Katharina Gerstenberger

    2012-01-01

    Full Text Available Literary texts about historical disasters tend to offer moral, political, or scientific interpretations of the occurrence that go well beyond the immediate experience of a catastrophe. They are, almost exclusively, written by people who did not in fact experience the catastrophic event. Survivor accounts, by contrast, typically do not have literary qualities. Phi Phi Island, the Austrian writer and essayist Josef Haslinger's literary report on how he and his family lived through the tsunami of 2004, is an exception. Point of departure for Haslinger's narrative is his inability to rejoice in the fact that he is alive. Carefully crafted and beautifully realized, his text combines the reconstruction of the events with reflections about how one can tell such a story in the first place. This essay analyzes Haslinger's strategies for coming to terms with the coincidence of survival, observing that the very personal nature of the report stands in noticeable contrast to the writer's commitment to political commentary in his other works.

  3. Starvation-Survival in Haloarchaea

    Science.gov (United States)

    Winters, Yaicha D.; Lowenstein, Tim K.; Timofeeff, Michael N.

    2015-01-01

    Recent studies claiming to revive ancient microorganisms trapped in fluid inclusions in halite have warranted an investigation of long-term microbial persistence. While starvation-survival is widely reported for bacteria, it is less well known for halophilic archaea—microorganisms likely to be trapped in ancient salt crystals. To better understand microbial survival in fluid inclusions in ancient evaporites, laboratory experiments were designed to simulate growth of halophilic archaea under media-rich conditions, complete nutrient deprivation, and a controlled substrate condition (glycerol-rich) and record their responses. Haloarchaea used for this work included Hbt. salinarum and isolate DV582A-1 (genus Haloterrigena) sub-cultured from 34 kyear Death Valley salt. Hbt. salinarum and DV582A-1 reacted to nutrient limitation with morphological and population changes. Starved populations increased and most cells converted from rods to small cocci within 56 days of nutrient deprivation. The exact timing of starvation adaptations and the physical transformations differed between species, populations of the same species, and cells of the same population. This is the first study to report the timing of starvation strategies for Hbt. salinarum and DV582A-1. The morphological states in these experiments may allow differentiation between cells trapped with adequate nutrients (represented here by early stages in nutrient-rich media) from cells trapped without nutrients (represented here by experimental starvation) in ancient salt. The hypothesis that glycerol, leaked from Dunaliella, provides nutrients for the survival of haloarchaea trapped in fluid inclusions in ancient halite, is also tested. Hbt. salinarum and DV582A-1 were exposed to a mixture of lysed and intact Dunaliella for 56 days. The ability of these organisms to utilize glycerol from Dunaliella cells was assessed by documenting population growth, cell length, and cell morphology. Hbt. salinarum and DV582A-1

  4. Starvation-Survival in Haloarchaea

    Directory of Open Access Journals (Sweden)

    Yaicha D. Winters

    2015-11-01

    Full Text Available Recent studies claiming to revive ancient microorganisms trapped in fluid inclusions in halite have warranted an investigation of long-term microbial persistence. While starvation-survival is widely reported for bacteria, it is less well known for halophilic archaea—microorganisms likely to be trapped in ancient salt crystals. To better understand microbial survival in fluid inclusions in ancient evaporites, laboratory experiments were designed to simulate growth of halophilic archaea under media-rich conditions, complete nutrient deprivation, and a controlled substrate condition (glycerol-rich and record their responses. Haloarchaea used for this work included Hbt. salinarum and isolate DV582A-1 (genus Haloterrigena sub-cultured from 34 kyear Death Valley salt. Hbt. salinarum and DV582A-1 reacted to nutrient limitation with morphological and population changes. Starved populations increased and most cells converted from rods to small cocci within 56 days of nutrient deprivation. The exact timing of starvation adaptations and the physical transformations differed between species, populations of the same species, and cells of the same population. This is the first study to report the timing of starvation strategies for Hbt. salinarum and DV582A-1. The morphological states in these experiments may allow differentiation between cells trapped with adequate nutrients (represented here by early stages in nutrient-rich media from cells trapped without nutrients (represented here by experimental starvation in ancient salt. The hypothesis that glycerol, leaked from Dunaliella, provides nutrients for the survival of haloarchaea trapped in fluid inclusions in ancient halite, is also tested. Hbt. salinarum and DV582A-1 were exposed to a mixture of lysed and intact Dunaliella for 56 days. The ability of these organisms to utilize glycerol from Dunaliella cells was assessed by documenting population growth, cell length, and cell morphology. Hbt. salinarum

  5. Survival of adult martens in Northern Wisconsin

    Science.gov (United States)

    Nicholas P. McCann; Patrick A. Zollner; Jonathan H. Gilbert

    2010-01-01

    Low adult marten (Martes americana) survival may be one factor limiting their population growth >30 yr after their reintroduction in Wisconsin, USA. We estimated annual adult marten survival at 0.81 in northern Wisconsin, with lower survival during winter (0.87) than summer-fall (1.00). Fisher (Martes pennanti) and raptor kills...

  6. Long-term survival after perforated diverticulitis

    NARCIS (Netherlands)

    J. Vermeulen (Jan); M.P. Gosselink (Martijn Pieter); W.C.J. Hop (Wim); E. van der Harst (Erwin); B.E. Hansen (Bettina); G.H.H. Mannaerts (Guido); P-P. Coene (Peter Paul); W.F. Weidema (Wibo); J.F. Lange (Johan)

    2011-01-01

    textabstractAim: Short-term survival after emergency surgery for perforated diverticulitis is poor. Less is known about long-term survival. The aims of this study were to evaluate long-term survival after discharge from hospital and to identify factors associated with prognosis. Method: All patients

  7. Clustered survival data with left-truncation

    DEFF Research Database (Denmark)

    Eriksson, Frank; Martinussen, Torben; Scheike, Thomas H.

    2015-01-01

    Left-truncation occurs frequently in survival studies, and it is well known how to deal with this for univariate survival times. However, there are few results on how to estimate dependence parameters and regression effects in semiparametric models for clustered survival data with delayed entry...

  8. 46 CFR 174.320 - Damage survival.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Damage survival. 174.320 Section 174.320 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SUBDIVISION AND STABILITY SPECIAL RULES PERTAINING TO... survival. A hopper dredge survives assumed damage if it meets the following conditions: (a) The maximum...

  9. Surviving the crash: T-cell homeostasis

    Indian Academy of Sciences (India)

    TOSHIBA

    Spatial and temporal elements. – Cellular sites for the integration of cell death and survival cues. – Spatial regulation of Notch activity for cell survival. Page 4. Cell survival is determined by the availability and uptake of nutrients live dead. Activated T-cells. T-cells. Page 5. dead wildtype. Bax active -6A7. Nucleus – H33342.

  10. Survival strategies in arctic ungulates

    Directory of Open Access Journals (Sweden)

    N. J. C. Tyler

    1990-09-01

    Full Text Available Arctic ungulates usually neither freeze nor starve to death despite the rigours of winter. Physiological adaptations enable them to survive and reproduce despite long periods of intense cold and potential undernutrition. Heat conservation is achieved by excellent insulation combined with nasal heat exchange. Seasonal variation in fasting metabolic rate has been reported in several temperate and sub-arctic species of ungulates and seems to occur in muskoxen. Surprisingly, there is no evidence for this in reindeer. Both reindeer and caribou normally maintain low levels of locomotor activity in winter. Light foot loads are important for reducing energy expenditure while walking over snow. The significance and control of selective cooling of the brain during hard exercise (e.g. escape from predators is discussed. Like other cervids, reindeer and caribou display a pronounced seasonal cycle of appetite and growth which seems to have an intrinsic basis. This has two consequences. First, the animals evidently survive perfectly well despite enduring negative energy balance for long periods. Second, loss of weight in winter is not necessarily evidence of undernutrition. The main role of fat reserves, especially in males, may be to enhance reproductive success. The principal role of fat reserves in winter appears to be to provide a supplement to, rather than a substitute for, poor quality winter forage. Fat also provides an insurance against death during periods of acute starvation.

  11. Foreign Ownership and Long-term Survival

    DEFF Research Database (Denmark)

    Kronborg, Dorte; Thomsen, Steen

    2006-01-01

    Does foreign ownership enhance or decrease a firm's chances of survival? Over the 100 year period 1895-2001 this paper compares the survival of foreign subsidiaries in Denmark to a control sample matched by industry and firm size. We find that foreign-owned companies have higher survival...... probability. On average exit risk for domestic companies is 2.3 times higher than for foreign companies. First movers like Siemens, Philips, Kodak, Ford, GM or Goodyear have been active in the country for almost a century. Relative foreign survival increases with company age. However, the foreign survival...

  12. Friedel-Crafts acylation of the 2-methoxynaphthalene using the silica-supported dodecatungstophosphoric acid (HPW/SiO{sub 2}) as catalyst and acetonitrile as solvent; Acilacao de Friedel-Crafts do 2-metoxinaftaleno usando o acido dodecafosfotungstico suportado em silica (HPW/SiO{sub 2}) como catalisador e acetonitrila como solvente

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Gil Luciano Guedes dos; Silva, Creuza Souza; Cardoso, Luiz Augusto Martins [Universidade Estadual do Sudoeste da Bahia, Jequie, BA (Brazil). Dept. de Quimica e Exatas

    2010-07-01

    The synthesis of fine chemicals intermediates using Friedel-Crafts acylation is one of the most important methods in chemical technology. In this work, the acylation of 2-methoxynaphthalene with acetic anhydride using a silica-supported dodeca tungstophosphoric acid catalyst (HPW/SiO{sub 2}) and acetonitrile as solvent was studied, showing that this reaction is a feasible alternative to produce intermediaries to replace the current methods of production. The reactions using acetonitrile solvent showed yields greater than or equal to the reactions using traditional solvents such as nitrobenzene and dichloroethane. Finally, the modified Eley-Rideal mechanism was proposed to elucidate the experimental data obtained. (author)

  13. Acilação de Friedel-Crafts do 2-metoxinaftaleno usando o ácido dodecafosfotúngstico suportado em sílica (HPW/SiO2 como catalisador e acetonitrila como solvente Friedel-Crafts acylation of the 2-methoxynaphthalene using the silica-supported dodecatungstophosphoric acid (HPW/SiO2 as catalyst and acetonitrile as solvent

    Directory of Open Access Journals (Sweden)

    Gil Luciano Guedes dos Santos

    2010-01-01

    Full Text Available The synthesis of fine chemicals intermediates using Friedel-Crafts acylation is one of the most important methods in chemical technology. In this work, the acylation of 2-methoxynaphthalene with acetic anhydride using a silica-supported dodecatungstophosphoric acid catalyst (HPW/SiO2 and acetonitrila as solvent was studied, showing that this reaction is a feasible alternative to produce intermediaries to replace the current methods of production. The reactions using acetonitrile solvent showed yields greater than or equal to the reactions using traditional solvents such as nitrobenzene and dichloroethane. Finally, the modified Eley-Rideal mechanism was proposed to elucidate the experimental data obtained.

  14. [Development of simple tools for risk identification and prevention of WMSDs (work related muscular-skeletal disorders): application experience in small and craft industries].

    Science.gov (United States)

    Colombini, Daniela; Occhipinti, E

    2011-01-01

    When studying WMSDs, multiple factors of different nature (mechanical, organizational, psychosocial, individual) and their interrelationship are considered relevant; consequently, the need for a "holistic" approach to MSD prevention was established. However, in recent years, considering the widespread presence of WMSDs in various work contexts there is a strong demand from OSH agencies and operators to develop "simple" tools for risk assessment and management, usable also by non-experts both in developed and developing countries, and in particular in craft industries and SME (small-medium enterprises). The World Health Organization (WHO) promoted the development of "toolkits" for different occupational risks and diseases; in outlining a toolkit (for WMSDs prevention), WHO defines this as "a set of practical risk assessment procedures and related management guidance documents, including advice on simple risk control options". The "Ergonomics of Posture and Movement" Research Unit (EPM) is very much involved in the WHO project for developing a "toolkit for MSD prevention" (as well as in similar issues promoted by ISO or UE); attention was consequently focused on craft industries, small enterprises and "difficult" work sectors (i.e. agriculture, fisheries, construction). In these sectors simple tools, procedures and software were developed and applied, that could facilitate WMSDs risk assessment and management. This issue of "La Medicina del Lavoro" is entirely devoted to selected papers regarding the above proposals and experience, especially in craft industries. The opening paper is a basic methodological contribution presenting a procedure and a tool (with relative software) that is useful for the identification of a number of occupational risks by means of special "key-enters"; the same tool, with special regard to WMSDs, defines criteria for a "quick risk assessment" which is mainly aimed at identifying 3 possible conditions: Acceptable (no remedial actions

  15. Looking at the work of Raul Lino, in comparison with Frank Lloyd Wright: from the Arts & Crafts, the nature, the organic and the house

    OpenAIRE

    José Manuel Fernandes

    2016-01-01

    El texto hace un análisis comparativo de las obras de Raul Lino (1879-1974), portugués, y Frank Lloyd Wright (1867-1959), de Estados Unidos- dos arquitectos (casi) contemporáneos, cada uno exponente de la cultura y la sociedad de su tiempo y de su espacio de vida y de trabajo.El artículo se refiere al contexto histórico y cultural del primer periodo creativo de estos autores. En este contexto trata de las obras de John Ruskin y William Morris, creadores del Arts & Crafts, así como de las cara...

  16. A reactivity-selectivity study of the Friedel-Crafts acetylation of 3,3′-dimethylbiphenyl and the oxidation of the acetyl derivatives

    Directory of Open Access Journals (Sweden)

    Titinchi Salam JJ

    2012-06-01

    Full Text Available Abstract Background Friedel-Crafts acetylation is an important route to aromatic ketones, in research laboratories and in industry. The acetyl derivatives of 3,3′-dimethylbiphenyl (3,3′-dmbp have applications in the field of liquid crystals and polymers and may be oxidized to the dicarboxylic acids and derivatives that are of interest in cancer treatment. Findings The effect of solvent and temperature on the selectivity of monoacetylation of 3,3’-dmbp by the Perrier addition procedure was studied using stoichiometric amounts of reagents. 4-Ac-3,3′-dmbp was formed almost quantitatively in boiling 1,2-dichloroethane and this is almost twice the yield hitherto reported. Using instead a molar ratio of substrate:AcCl:AlCl3 equal to 1:4:4 or 1:6:6 in boiling 1,2-dichloroethane, acetylation afforded 4,4′- and 4,6′-diacetyl-3,3′-dmbp in a total yield close to 100%. The acetyl derivatives were subsequently converted to the carboxylic acids by hypochlorite oxidation. The relative stabilities of the isomeric products and the corresponding σ-complexes were studied by DFT calculations and the data indicated that mono- and diacetylation followed different mechanisms. Conclusions Friedel-Crafts acetylation of 3,3′-dmbp using the Perrier addition procedure in boiling 1,2-dichloroethane was found to be superior to other recipes. The discrimination against the 6-acetyl derivative during monoacetylation seems to reflect a mechanism including an AcCl:AlCl3 complex or larger agglomerates as the electrophile, whereas the less selective diacetylations of the deactivated 4-Ac-3,3′-dmbp are suggested to include the acetyl cation as the electrophile. The DFT data also showed that complexation of intermediates and products with AlCl3 does not seem to be important in determining the mechanism.

  17. Survival paths through the forest

    DEFF Research Database (Denmark)

    Mogensen, Ulla Brasch

    when the information is high-dimensional e.g. when there are many thousands of genes or markers. In these situations machine learning methods such as the random forest can still be applied and provide reasonable prediction accuracy. The main focus in this talk is the performance of random forest...... in particular when the response is three-dimensional. In a diagnostic study of inflammatory bowel disease three classes of patients have to be diagnosed based on microarray gene-expression data. The performance of random forest is compared on a probability scale and on a classification scale to elastic net....... In survival analysis with competing risks I present an extension of random forest using time-dependent pseudo-values to build event risk prediction models. This approach is evaluated with data from Copenhagen stroke study. Further, I will explain how to use the R-package "pec" to evaluate random forests using...

  18. MRI survival guide; MRT Basiskurs

    Energy Technology Data Exchange (ETDEWEB)

    Cardoza, J. [Alta Imaging Medical Group and Magnetic Imaging Affiliates, Berkeley, CA (United States); Herfkens, R.J. [eds.] [Stanford Univ., CA (United States). Medical Center

    1999-07-01

    The book is a German translation of an American textbook with the original title ''MRI Survival Guide'' and is intended to serve as an introductory guide for beginners or a reference book for quick information. Readers will find information on the fundamentals of the technology and methodology of MRI as well as all details of relevance to practice in a precise and easy-to-grasp arrangement, covering all anatomic areas of interest, illustrations and descriptions of characteristic signs of pathologic processes, high-quality and unusually large-sized diagnostic pictures, a modern didactic concept for quick orientiation, including surveys, tables, and reproductions for visualisation of contents. (orig./CB) [German] Praktisch jeder Mediziner wird im Laufe seiner Berufstaetigkeit mit der MRT konfrontiert - unabhaengig davon ob in der Radiologie, Orthopaedie, Gynaekologie, Chirurgie, Neurologie oder sonstigen Fachrichtung. Das Buch ist eine Uebersetzung eines amerikanischen Lehrbuches mit dem Originaltitel ''MRI Survival Guide'' und will eine wesentliche Erleichterung als 'Ueberlebenshandbuch fuer die MRT' bieten: - Darstellung aller relevanten Grundlagen zu Technik, verschiedenen Sequenzen und Methodik der MRT - knapp und mit maximalem Praxisbezug - Beruecksichtigung aller moeglichen Untersuchungsregionen und strukturierte Orientierung daran (Gehirn, Wirbelsaeule, Kopf/Nacken, Brustkorb, Bauch, Becken, Muskel-Skelett-Bereich) - Illustration und Beschreibung der charakteristischen Erscheinungsmerkmale aller haeufigen pathologischen Prozesse im MRT, inklusive direkt umsetzbarer differentialdiagnostischer Abgrenzungskriterien - hochwertiges und aussergewoehnlich gross dimensioniertes Bildmaterial - modernes, didaktisches Konzept fuer die rasche Orientierung mit vielen Uebersichten, Tabellen und Abbildungen zur Visualisierung der Inhalte, Praxistips und Aufzeigen von Fehlermoeglichkeiten - zum Einstieg, zur Rekapitulation

  19. Shared Frailty Model for Left-Truncated Multivariate Survival Data

    DEFF Research Database (Denmark)

    Jensen, Henrik; Brookmeyer, Ron; Aaby, Peter

    multivariate survival data, left truncation, multiplicative hazard model, shared gamma frailty, conditional model, piecewise exponential model, childhood survival......multivariate survival data, left truncation, multiplicative hazard model, shared gamma frailty, conditional model, piecewise exponential model, childhood survival...

  20. The Survival and Birth of Firms

    OpenAIRE

    Leon Shilton; Craig Stanley

    1999-01-01

    Using a modified form of the location quotient, a "growth quotient," this study traces the survival and growth for the headquarters of publicly listed firms in the United States. At the county level, the spatial concentrations of headquarters listed in 1997 are correlated with the spatial concentrations of corporate headquarters that survived from 1986 though 1996. Counties that house the headquarters of many different survival firms continue to spawn new headquarters. Counties with headquart...

  1. Reflexive Aero Structures for Enhanced Survivability Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Cornerstone Research Group Inc. (CRG) proposes to develop an advanced reflexive structure system to increase the survivability of aerostructures. This reflexive...

  2. Surviving severe traumatic brain injury in Denmark

    DEFF Research Database (Denmark)

    Odgaard, Lene; Poulsen, Ingrid; Kammersgaard, Lars Peter

    2015-01-01

    PURPOSE: To identify all hospitalized patients surviving severe traumatic brain injury (TBI) in Denmark and to compare these patients to TBI patients admitted to highly specialized rehabilitation (HS-rehabilitation). PATIENTS AND METHODS: Patients surviving severe TBI were identified from...... severe TBI were admitted to HS-rehabilitation. Female sex, older age, and non-working status pre-injury were independent predictors of no HS-rehabilitation among patients surviving severe TBI. CONCLUSION: The incidence rate of hospitalized patients surviving severe TBI was stable in Denmark...

  3. Reflexive Aero Structures for Enhanced Survivability Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Cornerstone Research Group Inc. (CRG) will develop an advanced reflexive structure technology system to increase the survivability of future systems constructed of...

  4. Improving Survival in Decompensated Cirrhosis

    Directory of Open Access Journals (Sweden)

    Amar Nath Mukerji

    2012-01-01

    Full Text Available Mortality in cirrhosis is consequent of decompensation, only treatment being timely liver transplantation. Organ allocation is prioritized for the sickest patients based on Model for End Stage Liver Disease (MELD score. In order to improve survival in patients with high MELD score it is imperative to preserve them in suitable condition till transplantation. Here we examine means to prolong life in high MELD score patients till a suitable liver is available. We specially emphasize protection of airways by avoidance of sedatives, avoidance of Bilevel Positive Airway Pressure, elective intubation in grade III or higher encephalopathy, maintaining a low threshold for intubation with lesser grades of encephalopathy when undergoing upper endoscopy or colonoscopy as pre transplant evaluation or transferring patient to a transplant center. Consider post-pyloric tube feeding in encephalopathy to maintain muscle mass and minimize risk of aspiration. In non intubated and well controlled encephalopathy, frequent physical mobility by active and passive exercises are recommended. When renal replacement therapy is needed, night-time Continuous Veno-Venous Hemodialysis may be useful in keeping the daytime free for mobility. Sparing and judicious use of steroids needs to be borne in mind in treatment of ARDS and acute hepatitis from alcohol or autoimmune process.

  5. Survival From Childhood Hematological Malignancies in Denmark

    DEFF Research Database (Denmark)

    Erdmann, Friederike; Winther, Jeanette Falck; Dalton, Susanne Oksbjerg

    2016-01-01

    .76 (CI 2.01; 16.51) were observed for the fourth or later born children with ALL (N = 41) and AML (N = 9), respectively. Children with older parents showed a tendency toward inferior ALL survival, while for AML young maternal age was related to poorer survival. Based on small numbers, a trend toward...

  6. Zimbabwe's Exodus: Crisis, Migration, Survival | IDRC - International ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    2010-07-01

    Zimbabwe's Exodus: Crisis, Migration, Survival. Book cover Zimbabwe's Exodus: Crisis, Migration, Survival. Editor(s):. Jonathan Crush and Daniel Tevera. Publisher(s):. Southern African Migration Programme, IDRC. July 1, 2010. ISBN: 9781920409227. 420 pages. e-ISBN: 9781552504994. Download PDF · Read the e- ...

  7. Domesticating Ugandan local earthworms: Survival of African ...

    African Journals Online (AJOL)

    3.5; E, 90±2.8 and E. eugeniae There was significant effect (P<0.05) of feeding rate on the survival of both species and the Fisher's LSD multiple comparison test also showed significant different (P<0.05) in the survival among the two species.

  8. Cancer rehabilitation: a barometer for survival?

    Science.gov (United States)

    Saotome, Takako; Klein, Linda; Faux, Steven

    2015-10-01

    This pilot study was conducted to describe the clinical features and functional outcomes of patients attending inpatient rehabilitation for cancer-related deconditioning and neurological deficits and to explore factors associated with improved survival. Using a retrospective audit, demographic characteristics, discharge outcomes, survival time, and functional status as measured by Functional Independence Measure (FIM) were recorded for 73 patients. Clinical status was estimated by Karnofsky Performance Status Scale (KPS). Cox regression was used to assess factors associated with improved survival following discharge from rehabilitation. Significant functional gains following rehabilitation were observed in total FIM (p = 0.02), motor FIM (p = 0.001), and KPS (p = 0.003). Length of survival ranged from 9.0 to 25.0 months, with 26 cases surviving to the end of study (censored). Patients scoring a total FIM of ≥80 survived significantly longer than patients scoring <80 (p = 0.002). At discharge, motor FIM scores (p = 0.004), FIM Efficiency (p = 0.001), KPS scores (p = 0.022), ambulation ability (p = 0.026), return to home (p = 0.009), and receipt of in-home services (p = 0.045) were significantly associated with improved survival. Functional improvement achieved through inpatient rehabilitation was associated with prolonged survival among cancer patients. Rehabilitation leading to improved independence among cancer patients may act as a marker of those with greater likelihood of better prognosis.

  9. Nematode survival in relation to soil moisture

    NARCIS (Netherlands)

    Simons, W.R.

    1973-01-01

    Established nematode populations are very persistent in the soil. It is known that they need sufficient soil moisture for movement, feeding and reproduction (fig. 5), and that there are adverse soil moisture conditions which they cannot survive. The influence of soil moisture on survival

  10. Socioeconomic position and survival after cervical cancer

    DEFF Research Database (Denmark)

    Ibfelt, E H; Kjær, S K; Høgdall, C

    2013-01-01

    In an attempt to decrease social disparities in cancer survival, it is important to consider the mechanisms by which socioeconomic position influences cancer prognosis. We aimed to investigate whether any associations between socioeconomic factors and survival after cervical cancer could...... be explained by socioeconomic differences in cancer stage, comorbidity, lifestyle factors or treatment....

  11. MECHANICAL TRANSMISSION AND SURVIVAL OF BACTERIAL ...

    African Journals Online (AJOL)

    jen

    The transmission of enset bacterial wilt with contaminated knives and the survival of the causal agent in soil and enset plant debris was studied ... Xanthomonas campestris pv. musacearum (Xcm) isolates were observed to survive in the soil up to. 9 days. Thereafter the .... and needle, while pathogenicity tests were carried ...

  12. Long-term survival in Patau syndrome.

    Science.gov (United States)

    Tunca, Y; Kadandale, J S; Pivnick, E K

    2001-04-01

    A female patient with an extra chromosome 13 (Patau syndrome) is described. There are only five previous reports of patients with trisomy 13 who have survived past the first decade. It is concluded that non-lethal congenital anomalies and aggressive medical care play an important role in the survival of patients with trisomy 13.

  13. EFFECT OF SALINITY ON SURVIVAL AND LARVAL ...

    African Journals Online (AJOL)

    Laboratory investigations was conducted to gain a better insight into the effect of changing salinity regime on the development and survival of Macrobrachium vollenhoveli larvae. At water temperature of 28 ± 2oC, larvae reared in the salinity range of 0 to 10 ppt showed low survival (<48%), whereas those reared at 12 ...

  14. Escherichia coli survival in waters: Temperature dependence

    Science.gov (United States)

    Knowing the survival rates of water-borne Escherichia coli is important in evaluating microbial contamination and making appropriate management decisions. E. coli survival rates are dependent on temperature, a dependency that is routinely expressed using an analogue of the Q10 mo...

  15. Relief for surviving relatives following a suicide.

    NARCIS (Netherlands)

    Oud, MJT; de Groot, MH

    2006-01-01

    Relief for surviving relatives following a suicide. - After the suicide of a 43-year-old woman with known depression, a 41-year-old paraplegic man who recently developed diarrhoea and a 41-year-old woman with probable depression with symptoms of psychosis, the general practitioners of the surviving

  16. Survival after in-hospital Cardiopulmonary Resuscitation

    Directory of Open Access Journals (Sweden)

    M Adib Hajbaghery

    2005-05-01

    Full Text Available Background: During recent years, cardiopulmonary resuscitation (CPR in hospital has received much attention. However, the survival rate of CPR in Iran’s hospitals is unknown. This study was designed to evaluate outcome of in-hospital CPR in Kashan. Methods: A longitudinal case registry study was conducted on all cases of in-hospital CPR during 6 months at 2002. Necessary data including; age, sex, underlying disease, working shift, time from cardiac arrest until initiating of CPR and until defibrillation, duration and result of CPR, frequency of tracheal intubations and time served for it were collected in a checklist. Results: In six months study, 206 cases of cardiopulmonary resuscitation attempted. The survival rate was similar for both sexes. Short-term survival observed in19.9% of cases and only 5.3% survived to discharge. Conclusions: Duration of CPR, time of the first defibrillation, response time and the location of cardiac arrest are the key predictors of survival to hospital discharge and in-hospital CPR strategies require improvement. This study promotes a national study on post CPR survival for accurate data on our performance in attention to chain of survival. KeyWords: Cardiopulmonary Resuscitation (CPR, Survival rate, Iran

  17. Racial differences in survival from gynecologic cancer.

    Science.gov (United States)

    Morgan, M A; Behbakht, K; Benjamin, I; Berlin, M; King, S A; Rubin, S C

    1996-12-01

    To determine whether survival from gynecologic cancer is different between African-American and white patients at an inner-city hospital with both a large clinic and a private service. We studied 538 patients (89 African American, 449 white) diagnosed with cervical, uterine, or ovarian cancer at a single institution from January 1, 1989 through December 31, 1993. Information was obtained on age, stage, site of disease, histology, and type of health insurance (public or commercial). Insurance coverage was used as a proxy for socioeconomic status. Overall survival was estimated by the method of Kaplan and Meier and compared by the log-rank test. Cox proportional hazard modeling was used to evaluate the effects of multiple factors on survival. African-American patients were significantly older and were more likely to have cervical cancer and public insurance than white patients. Overall survival was worse for African-American patients than for white patients (P whites, and African-American patients older than 65 years had a worse survival than whites of similar age. On multivariate analysis, only stage and insurance coverage were significant predictors of survival. African-American patients with gynecologic cancer at our institution have worse overall survival than white patients. The survival difference seems to be due predominantly to differences in socioeconomic status and stage at diagnosis.

  18. Microbial survival and odor in laundry

    DEFF Research Database (Denmark)

    Jepsen, Signe Munk; Johansen, Charlotte; Stahnke, Louise Heller

    2001-01-01

    , hydrophobic odorants [(Z)-4- heptenal, (E)-2-nonenal, and guaiacol] adhered more strongly to polyester than the acids. The odor formed by surviving skin microflora attached to textiles soiled with human sebum and sweat after laundering at 30 degreesC was studied by sensory evaluation and aroma extract......-were evaluated on cotton textile. A significant survival and transfer between textiles were found for all four test strains washed in E.U. and U.S. color detergents (without bleach), whereas no survival was observed in bleach-containing detergents. Gram-negative strains generally survived in greater numbers than...... Gram-positive strains. A greater survival was observed in U.S. detergents at U.S. conditions (30 degreesC, 12 min) than in E.U. detergents at E.U. conditions (40 degreesC, 30 min). The adhesion of odorants to cotton and polyester textiles during washing and drying was studied using six previously...

  19. Seasonal survival of adult female mottled ducks

    Science.gov (United States)

    Moon, Jena A.; Haukos, David A.; Conway, Warren C.

    2017-01-01

    The mottled duck (Anas fulgivula) is a non-migratory duck dependent on coastal habitats to meet all of its life cycle requirements in the Western Gulf Coast (WGC) of Texas and Louisiana, USA. This population of mottled ducks has experienced a moderate decline during the past 2 decades. Adult survival has been identified as an important factor influencing population demography. Previous work based on band-recovery data has provided only annual estimates of survival. We assessed seasonal patterns of female mottled duck survival from 2009 to 2012 using individuals marked with satellite platform transmitter terminals (PTTs). We used temperature and movement sensors within each PTT to indicate potential mortality events. We estimated cumulative weekly survival and ranked factors influential in patterns of mortality using known-fate modeling in Program MARK. Models included 4 predictors: week; hunting and non-hunting periods; biological periods defined as breeding, brooding, molt, and pairing; and mass at time of capture. Models containing hunt periods, during and outside the mottled duck season, comprised essentially 100% of model weights where both legal and illegal harvest had a negative influence on mottled duck survival. Survival rates were low during 2009–2011 (12–38% annual rate of survival), when compared with the long-term banding average of 53% annual survival. During 2011, survival of female mottled ducks was the lowest annual rate (12%) ever documented and coincided with extreme drought. Management actions maximizing the availability of wetlands and associated upland habitats during hunting seasons and drought conditions may increase adult female mottled duck survival.

  20. A Large Scale Formal Synthesis of CoQ{sub 10}: Highly Stereoselective Friedel-Crafts Allylation Reaction of Tetramethoxytoluene with (E)-4-Chloro-2-methyl-1-phenylsulfonyl-2-butene in the Presence of Montmorillonite K-10

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Sang Who; Lee, Hee Bong; Kim, Bong Chan; Sadaiah, Kadivendi; Lee, Kyuwoong; Shin, Hyunik [LG Life Sciences, Ltd., Daejeon (Korea, Republic of)

    2013-04-15

    We disclosed that MK-10 is a highly effective catalyst for the Friedel-Crafts reaction of 6 and 7 in terms of yield and of stereoselectivity. Although there are numerous applications of clays in Friedel-Crafts reaction, there is very limited example which demonstrated its effect on the stereoselectivity. In that context, our result is significant and further expansion in this direction is highly envisioned. Ubiquinone, as its name represents, exists ubiquitously in human body, particularly in the heart. It mediates the electron transfer process in mitochondria and also exerts strong antioxidant effect in its reduced form. In clinical trial, it showed beneficial effect on heart-related diseases such as myocardial infarction, angina, and other related symptoms to cause decreased mortality compared to the placebo group.