Interaction between a hydrophobic rigid face and a flexible alkyl tail: Thermodynamics of self-assembling of sodium cholate and SDS

International Nuclear Information System (INIS)

Bai, Guangyue; Sheng, Jianhui; Wang, Yujie; Wu, Hui; Zhao, Yang; Zhuo, Kelei; Bastos, Margarida

2016-01-01

Highlights: • Critical concentrations and enthalpy changes for stepwise aggregation are obtained by ITC. • ITC allowed the thermodynamic characterization for NaCA/SDS self-assembling. • Steroid face-to-alkyl chain hydrophobic interaction tends to be saturated at molar ratio 1:1.5. • Alkyl-steroid interaction favors micellization of NaCA/SDS and the mixture shows nonideal behavior. • Intermolecular interaction and excess enthalpies were discussed according to Rubingh’s model. - Abstract: The thermodynamics of molecular self-assembling of an anionic biosurfactant, sodium cholate (NaCA) and its mixtures with sodium dodecyl sulfate (SDS) in aqueous solution have been investigated by isothermal titration calorimetry (ITC), along with fluorescence and conductivity measurements. Different critical concentrations were obtained by these three techniques – critical pre-micelle concentration (cmc_p_r_e) and critical micelle concentration (cmc) for pure NaCA, and critical micelle concentrations (cmc_m_i_x) for the mixed systems with differently initial SDS concentrations. Importantly, ITC allowed us to directly measure the enthalpy changes of pre-micelle formation (ΔH_p_r_e_m_i_c = (−0.28 ± 0.02) kJ·mol"−"1) and of micelle formation (ΔH_m_i_c = (−1.76 ± 0.05) kJ·mol"−"1) for pure NaCA as well as the enthalpies for micellization for the mixed systems NaCA/SDS. The non-ideality of the mixed surfactant solution was evaluated in terms of interaction parameters and excess enthalpies that were calculated in the light of Clint’s and Rubingh’s models. It was found that there is an obvious synergistic effect in the NaCA/SDS mixed system. From all these results we can ascribe the strong interaction between the same charge surfactants NaCA and SDS to the structural difference in their hydrophobic moieties. In fact, the flexible alkyl chains of SDS and the non-planar hydrophobic β-faces of NaCA tend to have a more compact packing than pure NaCA.

Study of adjuvant effect of model surfactants from the groups of alkyl sulfates, alkylbenzene sulfonates, alcohol ethoxylates and soaps

DEFF Research Database (Denmark)

Clausen, S K; Sobhani, S; Poulsen, O M

2000-01-01

The sodium salts of representatives of anionic surfactants, dodecylbenzene sulfonate (SDBS), dodecyl sulfate (SDS) and coconut oil fatty acids, and a nonionic surfactant, dodecyl alcohol ethoxylate, were studied for adjuvant effect on the production of specific IgE antibodies in mice. The surfact......The sodium salts of representatives of anionic surfactants, dodecylbenzene sulfonate (SDBS), dodecyl sulfate (SDS) and coconut oil fatty acids, and a nonionic surfactant, dodecyl alcohol ethoxylate, were studied for adjuvant effect on the production of specific IgE antibodies in mice...

Structure of sodium alkyl sulphate micelles

International Nuclear Information System (INIS)

Vass, Sz.

1990-05-01

Micellar aggregation numbers of aggregated sodium octyl, decyl, dodecyl and tetradecyl sulphate molecules obtained from small-angle neutron scattering (SANS) measurements are reported. The surfactant concentration and solution temperature were varied systematically. A survey of the physical models and evaluation algorithms applied for SANS are presented. By utilizing a new least square fitting algorithm, the formation and annihilation parameters of orthopositronium in the micellar pseudophase and in the aqueous solvent is deduced by evaluating positron lifetime spectra measured by conventional technqiues. (R.P.) 157 refs.; 10 figs

Safety Assessment of Amino Acid Alkyl Amides as Used in Cosmetics.

Science.gov (United States)

Burnett, Christina L; Heldreth, Bart; Bergfeld, Wilma F; Belsito, Donald V; Hill, Ronald A; Klaassen, Curtis D; Liebler, Daniel C; Marks, James G; Shank, Ronald C; Slaga, Thomas J; Snyder, Paul W; Andersen, F Alan

The Cosmetic Ingredient Review Expert Panel (Panel) reviewed the product use, formulation, and safety data of 115 amino acid alkyl amides, which function as skin and hair conditioning agents and as surfactants-cleansing agents in personal care products. Safety test data on dermal irritation and sensitization for the ingredients with the highest use concentrations, lauroyl lysine and sodium lauroyl glutamate, were reviewed and determined to adequately support the safe use of the ingredients in this report. The Panel concluded that amino acid alkyl amides are safe in the present practices of use and concentration in cosmetics, when formulated to be nonirritating.

Propargyl organometallic compounds. II. Alkylation of sodium derivatives of 1-alkyl-1-aryl-2-alkynes in liquid ammonia

International Nuclear Information System (INIS)

Libman, N.M.; Sevryukov, Yu.P.

1987-01-01

In most cases the alkylation of the sodium derivatives of 1-phenyl-1-alkyl-2-alkynes by methyl, ethyl, isopropyl, and tert-butyl bromides in liquid ammonia takes place preferentially at the sp 2 -hybridized carbon atom, and this leads to the formation of the corresponding acetylenes, The regioselectivity of the reaction is explained by the greater softness of the trigonal atom of the ambient propargyl anion and its smaller screening by the solvate shell compared with the diagonal atom

Determination of anionic surfactants during wastewater recycling process by ion pair chromatography with suppressed conductivity detection

Science.gov (United States)

Levine, L. H.; Judkins, J. E.; Garland, J. L.; Sager, J. C. (Principal Investigator)

2000-01-01

A direct approach utilizing ion pairing reversed-phase chromatography coupled with suppressed conductivity detection was developed to monitor biodegradation of anionic surfactants during wastewater recycling through hydroponic plant growth systems and fixed-film bioreactors. Samples of hydroponic nutrient solution and bioreactor effluent with high concentrations (up to 120 mS electrical conductance) of inorganic ions can be analyzed without pretreatment or interference. The presence of non-ionic surfactants did not significantly affect the analysis. Dynamic linear ranges for tested surfactants [Igepon TC-42, ammonium lauryl sulfate, sodium laureth sulfate and sodium alkyl (C10-C16) ether sulfate] were 2 to approximately 500, 1 to approximately 500, 2.5 to approximately 550 and 3.0 to approximately 630 microg/ml, respectively.

Interactions of short chain phenylalkanoic acids within ionic surfactant micelles in aqueous media

Directory of Open Access Journals (Sweden)

Naeem Kashif

2012-01-01

Full Text Available % SDS KR nema Solubilization and interactions of phenylalkanoic acids induced by cationic surfactant, cetyltrimethylammonium bromide (CTAB and an anionic surfactant, sodium dodecyl sulfate (SDS was investigated spectrophotometrically at 25.0°C. The UV spectra of the additives (acids were measured with and without surfactant above and below critical micelle concentration (cmc of the surfactant. The presence of alkyl chain in phenylalkanoic acids is responsible for hydrophobic interaction resulting in shift of the spectra towards longer wavelength (red shift. The value of partition coefficient (Kx between the bulk water and surfactant micelles and in turn standard free energy change of solubilization (ΔGpº were also estimated by measuring the differential absorbance (ΔA of the additives in micellar solutions.

Bioaccumulation of sodium alkyl sulfate zinc chloride and their mixture in young goby proterorhinus marmoratus pall

Energy Technology Data Exchange (ETDEWEB)

Topcuoglu, S.; Birol, E. (Cekmece Nuclear Research and Training Center, Istanbul (Turkey))

1982-12-01

The bioaccumulation of labelled surfactant, 35S-labelled sodium lauryl sulfate and 65Zn-labelled zinc chloride, was investigated both as a mixture and alone by themselves in young goby. The concentration factor of 7.15 was calculated for the surfactant in the whole-body fish and there was no effect of zinc chloride on this bioaccumulation process. Biological half-life of the surfactant was around 35 hours. The effects of surfactants on the zinc accumulation were also followed under the same conditions. The results indicated that the sodium lauryl sulfate had no effect on the accumulation of zinc, however, the other surfactant, linear alkylbenzene sulfonate, caused a significant increase in the zinc accumulation in comparison with the control group, during the uptake period.

Bioaccumulation of sodium alkyl sulfate zinc chloride and their mixture in young goby proterorhinus marmoratus pall

International Nuclear Information System (INIS)

Topcuoglu, S.; Birol, E.

1982-01-01

The bioaccumulation of labelled surfactant, 35S-labelled sodium lauryl sulfate and 65Zn-labelled zinc chloride, was investigated both as a mixture and alone by themselves in young goby. The concentration factor of 7.15 was calculated for the surfactant in the whole-body fish and there was no effect of zinc chloride on this bioaccumulation process. Biological half-life of the surfactant was around 35 hours. The effects of surfactants on the zinc accumulation were also followed under the same conditions. The results indicated that the sodium lauryl sulfate had no effect on the accumulation of zinc, however, the other surfactant, linear alkylbenzene sulfonate, caused a significant increase in the zinc accumulation in comparison with the control group, during the uptake period. (author)

Sequential One-Pot Ruthenium-Catalyzed Azide−Alkyne Cycloaddition from Primary Alkyl Halides and Sodium Azide

KAUST Repository

Johansson, Johan R.

2011-04-01

An experimentally simple sequential one-pot RuAAC reaction, affording 1,5-disubstituted 1H-1,2,3-triazoles in good to excellent yields starting from an alkyl halide, sodium azide, and an alkyne, is reported. The organic azide is formed in situ by treating the primary alkyl halide with sodium azide in DMA under microwave heating. Subsequent addition of [RuClCp*(PPh 3) 2] and the alkyne yielded the desired cycloaddition product after further microwave irradiation. © 2011 American Chemical Society.

Polyoxyethylene alkyl ether carboxylic acids: An overview of a neglected class of surfactants with multiresponsive properties.

Science.gov (United States)

Chiappisi, Leonardo

2017-12-01

In this work, an overview on aqueous solutions of polyoxyethylene alkyl ether carboxylic acids is given. Unique properties arise from the combination of the nonionic, temperature-responsive polyoxyethylene block with the weakly ionic, pH-responsive carboxylic acid termination in a single surfactant headgroup. Accordingly, this class of surfactant finds broad application across very different sectors. Despite their large use on an industrial and a technical scale, the literature lacks a systematic and detailed characterization of their physico-chemical properties which is provided herein. In addition, a comprehensive overview is given of their self-assembly and interfacial behavior, of their use as colloidal building blocks and for large-scale applications. Copyright © 2017 Elsevier B.V. All rights reserved.

Surfactant-enhanced electrokinetic remediation of soil contaminated with hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Yang, J.W.; Park, J.Y.; Lee, H.H.; Cho, H.J. [Dept. of Chemical Engineering, Korea Advanced Inst. of Science and Technology, Taejon (Korea)

2001-07-01

Removal of hydrophobic organic contaminants (HOCs) using electrokinetic method was studied in a model system. Kaolinite and phenanthrene were selected as the model clay soil and representative HOC. Three different types of surfactants, APG (alkyl polyglucoside), Brij30 (polyoxyethylene 4 lauryl ether), and SDS (sodium dodecyl sulfate), were used to enhance the solubility of HOCs. Electrokinetic (EK) column experiments were performed using water, surfactant solution, and acetate buffer solution under a constant current condition. Voltage and flow through the soil system were interpreted with time. Electrolyte pH at the anode and cathode compartments was observed for operation time. Removal efficiency of phenanthrene was examined after the end of EK operation during 2, 4, and 6 weeks. (orig.)

How Chain Length and Charge Affect Surfactant Denaturation of Acyl Coenzyme A Binding Protein (ACBP)

DEFF Research Database (Denmark)

Andersen, Kell Kleiner; Otzen, Daniel

2009-01-01

maltoside (DDM). The aim has been to determine how surfactant chain length and micellar charge affect the denaturation mechanism. ACBP denatures in two steps irrespective of surfactant chain length, but with increasing chain length, the potency of the denaturant rises more rapidly than the critical micelle......Using intrinsic tryptophan fluorescence, equilibria and kinetics of unfolding of acyl coenzyme A binding protein (ACBP) have been investigated in sodium alkyl sulfate surfactants of different chain length (8-16 carbon atoms) and with different proportions of the nonionic surfactant dodecyl...... constants increases linearly with denaturant concentration below the cmc but declines at higher concentrations. Both shortening chain length and decreasing micellar charge reduce the overall kinetics of unfolding and makes the dependence of unfolding rate constants on surfactant concentration more complex...

Influence of Valsartan on the thermodynamics of micellization of anionic surfactant Sodium Dodecyl Sulphate

Directory of Open Access Journals (Sweden)

Stopková L.

2016-12-01

Full Text Available In this manuscript was investigated behaviour of drug valsartan by micellar media of anionic surfactant sodium dodecyl sulphate. As the method was used electrical conductivity for the determination of critical micelle concentration at different temperatures (T = 293.15 - 313.15 K, as well as calculated thermodynamic parameters like standard Gibbs free energy, enthalpy and entropy of micellization. According to contribution of Gibbs free energy is the process of micellization primarily controlled by entropy. Solubilization of valsartan was studied in surfactant system at 298.15 K and physiological conditions pH 7.4 using UV-spectrophotometry at different concentration range (0.001 - 0.07 mol/l of sodium dodecyl sulphate. The solubilization of drug was observed with increasing concentration of surfactant in aqueous solution.

Alkyl polyglucoside vs. ethoxylated surfactant-based microemulsions as vehicles for two poorly water-soluble drugs: physicochemical characterization and in vivo skin performance

Directory of Open Access Journals (Sweden)

Pajić Nataša Z. Bubić

2017-12-01

Full Text Available Two types of biocompatible surfactants were evaluated for their capability to formulate skin-friendly/non-irritant microemulsions as vehicles for two poorly water-soluble model drugs differing in properties and concentrations: alkyl polyglucosides (decyl glucoside and caprylyl/capryl glucoside and ethoxylated surfactants (glycereth-7-caprylate/ caprate and polysorbate 80. Phase behavior, structural inversion and microemulsion solubilization potential for sertaconazole nitrate and adapalene were found to be highly dependent on the surfactants structure and HLB value. Performed characterization (polarized light microscopy, pH, electrical conductivity, rheological, FTIR and DSC measurements indicated a formulation containing glycereth- 7-caprylate/caprate as suitable for incorporation of both drugs, whereas alkyl polyglucoside-based systems did not exhibit satisfying solubilization capacity for sertaconazole nitrate. Further, monitored parameters were strongly affected by sertaconazole nitrate incorporation, while they remained almost unchanged in adapalene-loaded vehicles. In addition, results of the in vivo skin performance study supported acceptable tolerability for all investigated formulations, suggesting selected microemulsions as promising carriers worth exploring further for effective skin delivery of model drugs.

Alkyl polyglucoside vs. ethoxylated surfactant-based microemulsions as vehicles for two poorly water-soluble drugs: physicochemical characterization and in vivo skin performance.

Science.gov (United States)

Pajić, Nataša Z Bubić; Todosijević, Marija N; Vuleta, Gordana M; Cekić, Nebojša D; Dobričić, Vladimir D; Vučen, Sonja R; Čalija, Bojan R; Lukić, Milica Ž; Ilić, Tanja M; Savić, Snežana D

2017-12-20

Two types of biocompatible surfactants were evaluated for their capability to formulate skin-friendly/non-irritant microemulsions as vehicles for two poorly water-soluble model drugs differing in properties and concentrations: alkyl polyglucosides (decyl glucoside and caprylyl/capryl glucoside) and ethoxylated surfactants (glycereth-7-caprylate/ caprate and polysorbate 80). Phase behavior, structural inversion and microemulsion solubilization potential for sertaconazole nitrate and adapalene were found to be highly dependent on the surfactants structure and HLB value. Performed characterization (polarized light microscopy, pH, electrical conductivity, rheological, FTIR and DSC measurements) indicated a formulation containing glycereth- 7-caprylate/caprate as suitable for incorporation of both drugs, whereas alkyl polyglucoside-based systems did not exhibit satisfying solubilization capacity for sertaconazole nitrate. Further, monitored parameters were strongly affected by sertaconazole nitrate incorporation, while they remained almost unchanged in adapalene-loaded vehicles. In addition, results of the in vivo skin performance study supported acceptable tolerability for all investigated formulations, suggesting selected microemulsions as promising carriers worth exploring further for effective skin delivery of model drugs.

Impact of cationic surfactant on the self-assembly of sodium caseinate.

Science.gov (United States)

Vinceković, Marko; Curlin, Marija; Jurašin, Darija

2014-08-27

The impact of a cationic surfactant, dodecylammonium chloride (DDACl), on the self-assembly of sodium caseinate (SC) has been investigated by light scattering, zeta potential, and rheological measurements as well as by microscopy (transmission electron and confocal laser scanning microscopy). In SC dilute solutions concentration-dependent self-assembly proceeds through the formation of spherical associates and their aggregation into elongated structures composed of connected spheres. DDACl interacts with SC via its hydrophilic and hydrophobic groups, inducing changes in SC self-assembled structures. These changes strongly depend on the surfactant aggregation states (monomeric or micellar) as well as concentration ratio of both components, leading to the formation of soluble and insoluble complexes of nano- to microdimensions. DDACl monomers interact with SC self-assembled entities in a different way compared to their micelles. Surfactant monomers form soluble complexes (similar to surfactant mixed micelles) at lower SC concentration but insoluble gelatinous complexes at higher SC concentration. At surfactant micellar concentration soluble complexes with casein chains wrapped around surfactant micelles are formed. This study suggests that the use of proper cationic surfactant concentration will allow modification and control of structural changes of SC self-assembled entities.

Adsorption of dimeric surfactants in lamellar silicates

Energy Technology Data Exchange (ETDEWEB)

Balcerzak, Mateusz; Pietralik, Zuzanna [Department of Macromolecular Physics, Faculty of Physics, A. Mickiewicz University, Umultowska 85, 61-614 Poznań (Poland); Domka, Ludwik [Department of Metalorganic Chemistry, Faculty of Chemistry, A. Mickiewicz University, Grunwaldzka 6, 60-780 Poznań (Poland); Skrzypczak, Andrzej [Institute of Chemical Technology, Poznań University of Technology, Berdychowo 4, 60-965 Poznań (Poland); Kozak, Maciej, E-mail: mkozak@amu.edu.pl [Department of Macromolecular Physics, Faculty of Physics, A. Mickiewicz University, Umultowska 85, 61-614 Poznań (Poland)

2015-12-01

Highlights: • The intercalation of dimeric surfactants changed the morphology of MMT samples. • XRD indicated structures formed by surfactant molecules in interlayer space. • The four-step thermal decomposition of dimeric surfactant, confirms intercalation. - Abstract: The adsorption of different types of cationic surfactants in lamellar silicates changes their surface character from hydrophilic to hydrophobic. This study was undertaken to obtain lamellar silicates modified by a series of novel dimeric (gemini) surfactants of different length alkyl chains and to characterise these organophilised materials. Synthetic sodium montmorillonite SOMASIF® ME 100 (M) and enriched bentonite of natural origin (Nanoclay – hydrophilic bentonite®) were organophilised with dimeric (gemini) surfactants (1,1′-(1,4-butanediyl)bis(alkoxymethyl)imidazolium dichlorides). As a result of surfactant molecule adsorption in interlamellar space, the d-spacing (d{sub 001}) increased from 0.97 nm (for the anhydrous structure) to 2.04 nm. A Fourier transform infrared spectroscopy (FTIR) analysis of the modified systems reveals bands assigned to the stretching vibrations of the CH{sub 2} and CH{sub 3} groups and the scissoring vibrations of the NH group from the structure of the dimeric surfactants. Thermogravimetric (TG) and derivative thermogravimetric (DTG) studies imply a four-stage process of surfactant decomposition. Scanning electron microscopy (SEM) images provide information on the influence of dimeric surfactant intercalation into the silicate structures. Particles of the modified systems show a tendency toward the formation of irregularly shaped agglomerates.

Alkylating efficiency of sodium azide on pod yield, nut size and ...

African Journals Online (AJOL)

Mutation has been utilised to improve growth and yield of many food crops, but only little effort has been made to ascertain the nutritional advantages in such improved crops. The present study evaluates the alkylating efficiency of sodium azide of different concentrations on pod yield, nut size and nutritional composition of ...

Adsorption of anionic surfactants in limestone medium during oil recovery

Energy Technology Data Exchange (ETDEWEB)

Canbolat, Serhat; Bagci, Suat [Middle East Technical Univ., Dept. of Petroleum and Natural Gas Engineering, Ankara (Turkey)

2004-07-15

Foam-forming surfactant performance was evaluated by several experimental methods (interfacial tension, foam stability, corefloods) using commercial surfactants. There is considerable interest in the use of foam-forming surfactants for mobility control in water flood. To provide effective mobility control, the injected surfactant must propagate from the injection well toward the production well. One of the important parameters affecting propagation of foam-forming surfactant through the reservoir is the retention of surfactant due to its adsorption on reservoir rock. The determination of the adsorption of foam-forming surfactants in limestone reservoirs is important for the residual oil recovery efficiency. Adsorption measurements, recovery efficiencies, and surfactant and alkaline flooding experiments carried out with the representative of the selected surfactants alkaline solutions, linear alkyl benzene sulphonic acid (LABSA), sodium lauryl ether sulfate (SLES), and NaOH in a limestone medium. These surfactants were selected with respect to their foaming ability. Calibration curves formed by pH measurements were used to determine the correct adsorption amount of the used surfactants and recovery efficiency of these surfactants compared with base waterflooding. The results showed that LABSA adsorbed more than SLES in limestone reservoirs. The recovery efficiency of SLES was higher than the recovery efficiency of LABSA, and they decreased the recovery efficiency with respect to only the water injection case. (Author)

Thermodynamics of non-ionic surfactant Triton X-100-cationic surfactants mixtures at the cloud point

International Nuclear Information System (INIS)

Batigoec, Cigdem; Akbas, Halide; Boz, Mesut

2011-01-01

Highlights: → Non-ionic surfactants are used as emulsifier and solubilizate in such as textile, detergent and cosmetic. → Non-ionic surfactants occur phase separation at temperature as named the cloud point in solution. → Dimeric surfactants have attracted increasing attention due to their superior surface activity. → The positive values of ΔG cp 0 indicate that the process proceeds nonspontaneous. - Abstract: This study investigates the effects of gemini and conventional cationic surfactants on the cloud point (CP) of the non-ionic surfactant Triton X-100 (TX-100) in aqueous solutions. Instead of visual observation, a spectrophotometer was used for measurement of the cloud point temperatures. The thermodynamic parameters of these mixtures were calculated at different cationic surfactant concentrations. The gemini surfactants of the alkanediyl-α-ω-bis (alkyldimethylammonium) dibromide type, on the one hand, with different alkyl groups containing m carbon atoms and an ethanediyl spacer, referred to as 'm-2-m' (m = 10, 12, and 16) and, on the other hand, with -C 16 alkyl groups and different spacers containing s carbon atoms, referred to as '16-s-16' (s = 6 and 10) were synthesized, purified and characterized. Additions of the cationic surfactants to the TX-100 solution increased the cloud point temperature of the TX-100 solution. It was accepted that the solubility of non-ionic surfactant containing polyoxyethylene (POE) hydrophilic chain was a maximum at the cloud point so that the thermodynamic parameters were calculated at this temperature. The results showed that the standard Gibbs free energy (ΔG cp 0 ), the enthalpy (ΔH cp 0 ) and the entropy (ΔS cp 0 ) of the clouding phenomenon were found positive in all cases. The standard free energy (ΔG cp 0 ) increased with increasing hydrophobic alkyl chain for both gemini and conventional cationic surfactants; however, it decreased with increasing surfactant concentration.

SALT-INDUCED TRANSITION FROM A MICELLAR TO A LAMELLAR LIQUID-CRYSTALLINE PHASE IN DILUTE MIXTURES OF ANIONIC AND NONIONIC SURFACTANTS IN AQUEOUS-SOLUTION

NARCIS (Netherlands)

SEIN, A; ENGBERTS, JBFN; VANDERLINDEN, E; VANDEPAS, JC

In dilute mixtures of anionic surfactant, sodium dodecylbenzenesulfonate (NaDoBS), and nonionic poly(ethylene oxide) alkyl monoether (C13-15E(7)) a transition from a micellar to a lamellar phase is found at high salting-out electrolyte (NaCit) concentrations. With an increase of the salt

The hydrolysis of C12 primary alkyl sulfates in concentrated aqueous solutions. Part 2. Influence of alkyl structure on hydrolytic reactivity in concentrated aqueous mixtures of sodium primary alkyl sulfates : 1-benzoyl-3-phenyl-1,2,4-triazole as a probe o

NARCIS (Netherlands)

Bethell, Donald; Fessey, Roger E.; Engberts, Jan B.F.N.; Roberts, David W.

2001-01-01

The kinetics of the hydrolysis of aqueous solutions of three sodium C12-alkyl sulfates (SXS), sodium 2-methylundecyl sulfate (SMS), sodium cycloundecylmethyl sulfate (SCS) and sodium 2-pentylheptyl sulfate (SPS), has been investigated at concentrations up to 70% and compared with the behaviour of

Micellar solubilization in strongly interacting binary surfactant systems. [Binary surfactant systems of: dodecyltrimethylammonium chloride + sodium dodecyl sulfate; benzyldimethyltetradecylammonium chloride + tetradecyltrimethylammonium chloride

Energy Technology Data Exchange (ETDEWEB)

Treiner, C. (Universite Pierre et Marie Curie, Paris (France)); Nortz, M.; Vaution, C. (Faculte de Pharmacie de Paris-sud, Chatenay-Malabry (France))

1990-07-01

The apparent partition coefficient P of barbituric acids between micelles and water has been determined in mixed binary surfactant solutions from solubility measurements in the whole micellar composition range. The binary systems chosen ranged from the strongly interacting system dodecyltrimethylammonium chloride + sodium dodecyl sulfate to weakly interacting systems such as benzyldimethyltetradecylammonium chloride + tetradecyltrimethyammonium chloride. In all cases studied, mixed micelle formation is unfavorable to micellar solubilization. A correlation is found between the unlike surfactants interaction energy, as measured by the regular solution parameter {beta} and the solute partition coefficient change upon surfactant mixing. By use of literature data on micellar solubilization in binary surfactant solutions, it is shown that the change of P for solutes which are solubilized by surface adsorption is generally governed by the sign and amplitude of the interaction parameter {beta}.

The effect of the head group on branched-alkyl chain surfactants in glycolipid/n-octane/water ternary system.

Science.gov (United States)

Nainggolan, Irwana; Radiman, Shahidan; Hamzah, Ahmad Sazali; Hashim, Rauzah

2009-10-01

Two novel glycolipids have been synthesized and their phase behaviour studied. They have been characterized using FT-IR, FAB and 13C NMR and 1H NMR to ensure the purity of novel glycolipids. The two glycolipids are distinguished based on the head group of glycolipids (monosaccharide/glucose and disaccharide/maltose). These two novel glycolipids have been used as surfactant to perform two phase diagrams. Phase behaviours that have been investigated are 2-hexyldecyl-beta-D-glucopyranoside (2-HDG)/n-octane/water ternary system and 2-hexyldecyl-beta-D-maltoside (2-HDM)/n-octane/water ternary system. SAXS and polarizing optical microscope have been used to study the phase behaviours of these two surfactants in ternary phase diagram. Study of effect of the head group on branched-alkyl chain surfactants in ternary system is a strategy to derive the structure-property relationship. For comparison, 2-HDM and 2-HDG have been used as surfactant in the same ternary system. The phase diagram of 2-hexyldecyl-beta-D-maltoside/n-octane/water ternary system exhibited a Lalpha phase at a higher concentration regime, followed with two phases and a micellar solution region in a lower concentration regime. The phase diagram of 2-HDG/water/n-octane ternary system shows hexagonal phase, cubic phase, rectangular ribbon phase, lamellar phase, cubic phase as the surfactant concentration increase.

Cooperative Effects of Zwitterionic-Ionic Surfactant Mixtures on the Interfacial Water Structure Revealed by Sum Frequency Generation Vibrational Spectroscopy.

Science.gov (United States)

Pan, Xuecong; Yang, Fangyuan; Chen, Shunli; Zhu, Xuefeng; Wang, Chuanyi

2018-05-08

Cooperative effects of a series of equimolar binary zwitterionic-ionic surfactant mixtures on the interfacial water structure at the air-water interfaces have been studied by sum frequency generation vibrational spectroscopy (SFG-VS). For zwitterionic surfactant palmityl sulfobetaine (SNC 16 ), anionic surfactant sodium hexadecyl sulfate (SHS), and cationic surfactant cetyltrimethylammonium bromide (CTAB) with the same length of alkyl chain, significantly enhanced ordering of interfacial water molecules was observed for the zwitterionic-anionic surfactant mixtures SNC 16 -SHS, indicating that SNC 16 interacts more strongly with SHS than with CTAB because of the strong headgroup-headgroup electrostatic attraction for SNC 16 -SHS. Meanwhile, the SFG amplitude ratio of methyl and methylene symmetric stretching modes was used to verify the stronger interaction between SNC 16 and SHS. The conformational order indicator increased from 0.64 for SNC 16 to 7.17 for SNC 16 -SHS but only 0.94 for SNC 16 -CTAB. In addition, another anionic surfactant sodium dodecyl sulfate (SDS) was introduced to study the influence of chain-chain interaction. Decreased SFG amplitude of interfacial water molecules for SNC 16 -SDS was observed. Therefore, both the headgroup-headgroup electrostatic interaction and chain-chain van der Waals attractive interaction of the surfactants play an important role in enhancing the ordering of interfacial water molecules. The results provided experimental and theoretical bases for practical applications of the surfactants.

Polycation–sodium lauryl ether sulfate-type surfactant complexes : influence of ethylene oxide length

NARCIS (Netherlands)

Vleugels, L.F.W.; Pollet, J.; Tuinier, R.

2015-01-01

Polyelectrolyte-surfactant complexes (PESC) are a class of materials which form spontaneously by self-assembly driven by electrostatic and hydrophobic interactions. PESC containing sodium lauryl ether sulfates (SLES) have found wide application in hair care products like shampoo. Typically, SLES

Polycation-Sodium Lauryl Ether Sulfate-Type Surfactant Complexes : Influence of Ethylene Oxide Length

NARCIS (Netherlands)

Vleugels, Leo F. W.; Pollet, Jennifer; Tuinier, Remco

2015-01-01

Poiyelectrolyte-surfactant complexes (PESC) are a class of materials which form spontaneously by self-assembly driven by electrostatic and hydrophobic interactions. PESC containing sodium lauryl ether Sulfates (SLES) have found wide application in hair care products like shampoo. Typically, SLES

40 CFR 721.3130 - Sulfuric acid, mono-C9-11-alkyl esters, sodium salts.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Sulfuric acid, mono-C9-11-alkyl esters, sodium salts. 721.3130 Section 721.3130 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... significant new uses are: (i) Industrial, commercial, and consumer activities. Requirements as specified in...

Comparison of the orogenic displacement of sodium caseinate with the caseins from the air-water interface by nonionic surfactants.

Science.gov (United States)

Woodward, N C; Gunning, A P; Mackie, A R; Wilde, P J; Morris, V J

2009-06-16

Displacement of sodium caseinate from the air-water interface by nonionic surfactants Tween 20 and Tween 60 was observed by atomic force microscopy (AFM). The interfacial structure was sampled by Langmuir-Blodgett deposition onto freshly cleaved mica substrates. Protein displacement occurred through an orogenic mechanism: it involved the nucleation and growth of surfactant domains within the protein network, followed by failure of the protein network. The surface pressure at which failure of the protein network occurred was essentially independent of the type of surfactant. The major component of sodium caseinate is beta-casein, and previous studies at the air-water interface have shown that beta-casein networks are weak, failing at surface pressures below that observed for sodium caseinate. The other components of sodium caseinate are alpha(s)- and kappa-caseins. Studies of the displacement of alpha(s)-caseins from air-water interfaces show that these proteins also form weak networks that fail at surface pressures below that observed for sodium caseinate. However, kappa-casein was found to form strong networks that resisted displacement and failed at surface pressures comparable to those observed for sodium caseinate. The AFM images of the displacement suggest that, despite kappa-casein being a minor component, it dominates the failure of sodium caseinate networks: alpha(s)-casein and beta-casein are preferentially desorbed at lower surface pressures, allowing the residual kappa-casein to control the breakdown of the sodium caseinate network at higher surface pressures.

The structure of normal ionic micelles by interpretation of small-angle neutron scattering data from selectively labeled (2H, 19F) surfactant solutions

International Nuclear Information System (INIS)

Berr, S.S.

1986-12-01

We have determined the structure of micelles formed in water by several classes of ionic surfactants under a variety of experimental conditions using small-angle neutron scattering (SANS) techniques. Contrast between the micelles and the solvent was achieved through either selective deuteration or fluorination of the surfactant, or through the use of D 2 O. Interpretation of SANS data was facilitated by the use of Hayter, Penfold, and Hansen's rescaled Mean Spherical Approximation theory to calculate the scattering due to interparticle interactions. We have devised a number of micelle models, both spherical and ellipsoidal, to account for the scattering due to single micelles. It was found that changing the solvent from H 2 O to D 2 O results in the formation of larger micelles due to changes in the solvent-surfactant hydrocarbon interactions. This solvent isotope effect increased as the length of the alkyl chain increased. The fractional micellar charge did not change with respect to isotopic composition of solvent. We found that alkyltrimethylammonium bromide surfactants form drier micelles than do the sodium alkyl sulfate surfactants of equal chain length. Also, all micelles studied were found to be dry near the critical micelle concentration (cmc) and to become increasingly wetter as the concentration increased. The increase in aggregation number with respect to the square root of surfactant concentration was found to be linear for all systems studied. 80 figs

Ultrathin nanofibrous films prepared from cadmium hydroxide nanostrands and anionic surfactants.

Science.gov (United States)

Peng, Xinsheng; Karan, Santanu; Ichinose, Izumi

2009-08-04

We developed a simple fabrication method of ultrathin nanofibrous films from the dispersion of cadmium hydroxide nanostrands and anionic surfactants. The nanostrands were prepared in a dilute aqueous solution of cadmium chloride by using 2-aminoethanol. They were highly positively charged and gave bundlelike fibers upon mixing an aqueous solution of anionic surfactant. The nanostrand/surfactant composite fibers were filtered on an inorganic membrane filter. The resultant nanofibrous film was very uniform in the area of a few centimeters square when the thickness was not less than 60 nm. The films obtained with sodium tetradecyl sulfate (STS) had a composition close to the electroneutral complex, [Cd37(OH)68(H2O)n] x 6(STS), as confirmed by energy dispersive X-ray analysis. They were water-repellent with a contact angle of 117 degrees, and the value slightly decreased with the alkyl chain length of anionic surfactants. Ultrathin nanofibrous films were stable enough to be used for ultrafiltration at pressure difference of 90 kPa. We could effectively separate Au nanoparticles of 40 nm at an extremely high filtration rate of 14000 L/(h m2 bar).

Strong cooperative effect of oppositely charged surfactant mixtures on their adsorption and packing at the air-water interface and interfacial water structure.

Science.gov (United States)

Nguyen, Khoi T; Nguyen, Tuan D; Nguyen, Anh V

2014-06-24

Remarkable adsorption enhancement and packing of dilute mixtures of water-soluble oppositely-charged surfactants, sodium dodecyl sulfate (SDS) and dodecyl amine hydrochloride (DAH), at the air-water interface were observed by using sum frequency generation spectroscopy and tensiometry. The interfacial water structure was also observed to be significantly influenced by the SDS-DAH mixtures, differently from the synergy of the single surfactants. Most strikingly, the obtained spectroscopic evidence suggests that the interfacial hydrophobic alkyl chains of the binary mixtures assemble differently from those of single surfactants. This study highlights the significance of the cooperative interaction between the headgroups of oppositely charged binary surfactant systems and subsequently provides some insightful observations about the molecular structure of the air-aqueous interfacial water molecules and, more importantly, about the packing nature of the surfactant hydrophobic chains of dilute SDS-DAH mixtures of concentration below 1% of the CMC.

Surfactant flushing remediation of o-dichlorobenzene and p-dichlorobenzene contaminated soil.

Science.gov (United States)

Pei, Guangpeng; Zhu, Yuen; Cai, Xiatong; Shi, Weiyu; Li, Hua

2017-10-01

Surfactant-enhanced remediation is used to treat dichlorobenzene (DCB) contaminated soil. In this study, soil column experiments were conducted to investigate the removal efficiencies of o-dichlorobenzene (o-DCB) and p-dichlorobenzene (p-DCB) from contaminated soil using micellar solutions of biosurfactants (saponin, alkyl polyglycoside) compare to a chemically synthetic surfactant (Tween 80). Leachate was collected and analyzed for o-DCB and p-DCB content. In addition, soil was analyzed to explore the effect of surfactants on soil enzyme activities. Results showed that the removal efficiency of o-DCB and p-DCB was highest for saponin followed by alkyl polyglycoside and Tween 80. The maximum o-DCB and p-DCB removal efficiencies of 76.34% and 80.43%, respectively, were achieved with 4 g L -1 saponin solution. However, an opposite result was observed in the cumulative mass of o-DCB and p-DCB in leachate. The cumulative extent of o-DCB and p-DCB removal by the biosurfactants saponin and alkyl polyglycoside was lower than that of the chemically synthetic surfactant Tween 80 in leachate. Soil was also analyzed to explore the effect of surfactants on soil enzyme activities. The results indicated that surfactants were potentially effective in facilitating soil enzyme activities. Thus, it was confirmed that the biosurfactants saponin and alkyl polyglycoside could be used for remediation of o-DCB and p-DCB contaminated soil. Copyright © 2017 Elsevier Ltd. All rights reserved.

LOWER COST METHODS FOR IMPROVED OIL RECOVERY (IOR) VIA SURFACTANT FLOODING

Energy Technology Data Exchange (ETDEWEB)

William A. Goddard III; Yongchun Tang; Patrick Shuler; Mario Blanco; Seung Soon Jang; Shiang-Tai Lin; Prabal Maiti; Yongfu Wu; Stefan Iglauer; Xiaohang Zhang

2004-09-01

This report provides a summary of the work performed in this 3-year project sponsored by DOE. The overall objective of this project is to identify new, potentially more cost-effective surfactant formulations for improved oil recovery (IOR). The general approach is to use an integrated experimental and computational chemistry effort to improve our understanding of the link between surfactant structure and performance, and from this knowledge, develop improved IOR surfactant formulations. Accomplishments for the project include: (1) completion of a literature review to assemble current and new surfactant IOR ideas, (2) Development of new atomistic-level MD (molecular dynamic) modeling methodologies to calculate IFT (interfacial tension) rigorously from first principles, (3) exploration of less computationally intensive mesoscale methods to estimate IFT, Quantitative Structure Property Relationship (QSPR), and cohesive energy density (CED) calculations, (4) experiments to screen many surfactant structures for desirable low IFT and solid adsorption behavior, and (5) further experimental characterization of the more promising new candidate formulations (based on alkyl polyglycosides (APG) and alkyl propoxy sulfate surfactants). Important findings from this project include: (1) the IFT between two pure substances may be calculated quantitatively from fundamental principles using Molecular Dynamics, the same approach can provide qualitative results for ternary systems containing a surfactant, (2) low concentrations of alkyl polyglycoside surfactants have potential for IOR (Improved Oil Recovery) applications from a technical standpoint (if formulated properly with a cosurfactant, they can create a low IFT at low concentration) and also are viable economically as they are available commercially, and (3) the alkylpropoxy sulfate surfactants have promising IFT performance also, plus these surfactants can have high optimal salinity and so may be attractive for use in higher

Preparation of Organized Mesoporous Silica from Sodium Metasilicate Solutions in Alkaline Medium using Nonionic Surfactants

Czech Academy of Sciences Publication Activity Database

Zukalová, Markéta; Rathouský, Jiří; Zukal, Arnošt

2003-01-01

Roč. 68, č. 10 (2003), s. 2019-2031 ISSN 0010-0765 Institutional research plan: CEZ:AV0Z4040901 Keywords : mesoporous SiO2 * sodium metasilicate * nonionic surfactants Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 1.041, year: 2003

Thermodynamics of inclusion complex formation of β-cyclodextrin with a variety of surfactants differing in the nature of headgroup

International Nuclear Information System (INIS)

Benkő, Mária; Király, Zoltán

2012-01-01

Highlights: ► Inclusion complexation of β-cyclodextrins with various surfactants. ► Thermodynamic parameters determined by titration microcalorimetry. ► Stoichiometry of complexation is 1:1. ► The binding constant decreases linearly with increasing temperature. ► Enthalpy–entropy compensation is independent of the nature of the headgroup. - Abstract: The inclusion complexation of β-cyclodextrin with various surfactants, possessing the same alkyl chain length but differing in the hydrophilic headgroup, was investigated by isothermal titration microcalorimetry. Sodium dodecyl sulfate, sodium dodecyl sulfonate, dodecyltrimethylammonium bromide and dodecyl(dimethyl)amine oxide were investigated. The major aim of this study was to elucidate the effects of temperature and the nature of the headgroup on the complex formation. Thermometric titrations were effected between the temperatures (288 and 348) K. The results provided the stoichiometry, the equilibrium constant and the reaction enthalpy of complexation. Changes in Gibbs energy, entropy and van’t Hoff enthalpy were additionally calculated.

Modification of the activity of an alpha-amylase from Bacillus licheniformis by several surfactants

OpenAIRE

Bravo Rodríguez,Vicente; Jurado Alameda,Encarnación; Martínez Gallegos,Juan Francisco; Reyes Requena,Antonia; García López,Ana Isabel; Sampaio Cabral,Joaquim Manuel; Fernandes,Pedro; Pina da Fonseca,Luis Joaquim

2006-01-01

The influence of different commercial surfactants on the enzymatic activity of a commercial alpha-amylase from Bacillus licheniformis (Termamyl 300 L) has been studied. As non-ionic surfactants, alkyl polyglycosides (Glucopon® 215, Glucopon® 600 and Glucopon® 650) were studied, as were fatty alcohol ethoxylates (Findet 1214N/23 and Findet 10/15), and nonyl phenol ethoxylate (Findet 9Q/21.5NF). Also, an anionic surfactant, linear alkyl benzene sulfonate (LAS) was assayed. In general, none of t...

Aquatic toxicity and biodegradability of advanced cationic surfactant APA-22 compatible with the aquatic environment.

Science.gov (United States)

Yamane, Masayuki; Toyo, Takamasa; Inoue, Katsuhisa; Sakai, Takaya; Kaneko, Youhei; Nishiyama, Naohiro

2008-01-01

Cationic surfactant is a chemical substance used in hair conditioner, fabric softener and other household products. By investigating the relationship between the aquatic toxicity and the chemical structures of two types of mono alkyl cationic surfactants, alkyl trimethylammonium salts and alkyl dimethylamine salts, we have found that the C22 alkyl chain length is effective to reduce the toxicity. Besides, we have recognized that the amidopropyl functional group contributes to the enhanced biodegradability by investigating the biodegradation trend of (alkylamidopropyl)dimethylamine salt (alkyl chain length: C18). Based on these findings, we have developed mono alkyl cationic surfactant called APA-22, N-[3-(dimethylamino)propyl]docosanamide salt. APA-22 is formed by the C22 alkyl chain, amidopropyl functional group and di-methyltertiary amine group. We evaluated the aerobic and anaerobic biodegradability of APA-22 by two standard methods (OECD Test Guideline 301B and ECETOC technical document No.28) and found that this substance was degraded rapidly in both conditions. The toxicity to algae, invertebrate and fish of this substance are evaluated by using OECD Test Guideline 201, 202 and 203, respectively. All acute toxicity values are >1 mg/L, which indicates that environmental toxicity of this substance is relatively less toxic to aquatic organism. In addition, we estimated the biodegradation pathway of APA-22 and observed the complete disappearance of APA-22 and its intermediates during the test periods. Based on the environmental data provided above, we concluded that APA22 is more compatible with the aquatic environment compared to other cationic surfactants with mono long alkyl chain.

Effect of surfactant types and their concentration on the structural characteristics of nanoclay

Science.gov (United States)

Zawrah, M. F.; Khattab, R. M.; Saad, E. M.; Gado, R. A.

2014-03-01

A series of organo-modified nanoclays was synthesized using three different surfactants having different alkyl chain lengths and concentrations [0.5-5.0 cation exchange capacity (CEC)]. These surfactants were Ethanolamine (EA), Cetyltrimethylammoniumbromide (CTAB) and Tetraoctadecylammoniumbromide (TO). The obtained modified nanoclays were characterized by X-ray diffraction (XRD), Fourier Transform Infrared spectroscopy (FTIR) and Scanning electron microscopy (SEM) and compared with unmodified nanoclay. The results of XRD analysis indicated that the basal d-spacing has increased with increasing alkyl chain length and surfactant concentration. From the obtained microstructures of these organo-modified nanoclays, the mechanism of surfactant adsorption was proposed. At relatively low loading of surfactant, most of surfactant entered the spacing by an ion-exchange mechanism and is adsorbed onto the interlayer cation sites. When the concentration of the surfactant exceeds the CEC of clay, the surfactant molecules then adhere to the surface adsorbed surfactant. Some surfactants entered the interlayers, whereas the others were attached to the clay surface. When the concentration of surfactant increased further beyond 2.0 CEC, the surfactants might occupy the inter-particle space within the house-of-cards aggregate structure.

DETERMINATION OF SURFACTANT SODIUM LAURYL ETHER SULFATE BY ION PAIRING CHROMATOGRAPHY WITH SUPPRESSED CONDUCTIVITY DETECTION

Science.gov (United States)

A method for the determination of the anionic Steol CS-330 surfactant is described. CS-330 is a complex mixture of oligomers due to the various sizes of fatty alcohols and the number of moles of the ethoxylation. The main component of CS-330 is sodium lauryl ether sulfate (SLES)....

Enhancing the Drag Reduction Phenomenon within a Rotating Disk Apparatus Using Polymer-Surfactant Additives

Directory of Open Access Journals (Sweden)

Musaab K. Rashed

2016-12-01

Full Text Available Pipelines and tubes play important roles in transporting economic liquids, such as water, petroleum derivatives, and crude oil. However, turbulence reduces the initial flow rate at which liquids are pumped, thereby making liquid transportation through pipelines inefficient. This study focuses on enhancing the drag reduction (DR phenomenon within a rotating disk apparatus (RDA using polymer-surfactant additives. The complex mixture of polyisobutylene (PIB and sodium dioctyl sulfosuccinate (SDS was used. These materials were tested individually and as a complex mixture in RDA at various concentrations and rotational speeds (rpm. The morphology of this complex was investigated using transmission electronic microscopy (TEM. The reduction of the degradation level caused by the continuous circulation of surfactant additives in RDA could improve the long-term DR level. Experimental result shows that the maximum %DR of the complex mixture was 21.455% at 3000 rpm, while the PIB and SDS were 19.197% and 8.03%, respectively. Therefore, the complex mixture had better performance than these substances alone and were highly dependent on the alkyl chain of the surfactant.

Dynamic interfacial tension behavior of alkyl amino sulfonate in crude oil-brine system

Energy Technology Data Exchange (ETDEWEB)

Ren, Zhao Hua; Luo, Yue [Yangtze Univ., Jingzhou, Hubei (China). College of Chemistry and Environmental Engineering

2013-09-15

The compatibility of surfactants, a series of alkyl amino sulfonate containing various the length of alkyl chain (dodecyl, tetradecyl, hexadecyl and octadecyl, developed in our laboratory), with formation water matching the Xinjiang Oil Field reservoir water and the dynamic interfacial tensions (DIT) behaviors between the crude oil and the formation water for a number of alkaline flooding systems were measured. These surfactants are found to be well compatible with formation water up to 0.10g L{sup -1} surfactant concentration, especially Dodec-AS and Tetradec-AS show a good compatibility with formation water over the full range of surfactant concentration investigated (0.01-0.20g L{sup -1}). All surfactants exhibit the dynamic interfacial tension behavior, and can reach and maintain low interfacial tension at very low concentration. The time for reaching the equilibrium DIT (DIT{sub eq}) is longer for surfactant with stronger lipophilicity, e.g. octadecyl-AS. It is interestingly found that the ratio value between DIT{sub eq} and the tension at crude oil/reservoir water interface in the absence of surfactant is in the range of 10{sup -4}-10{sup -3} mN m{sup -1}, accordingly based on which and the previous results, four surfactants individually or with other additives together may become potent candidates for enhanced oil recovery. Fortunately, the alkyl amino sulfonate combinational systems without alkali designed by our group can reduce the interfacial tension even to 10{sup -4} mN m{sup -1} at very low surfactant concentration. These surfactants or their systems have characteristic of 'Green', in addition to the excellent salt-tolerance and the less expensive cost for enhanced oil recovery, and therefore they are good oil-displacing reagents for enhanced oil recovery. (orig.)

Evaluation of the mechanism of skin enhancing surfactants on the biomembrane of shed snake skin.

Science.gov (United States)

Wonglertnirant, Nanthida; Ngawhirunpat, Tanasait; Kumpugdee-Vollrath, Mont

2012-01-01

The aim of the present work was to investigate the effects of different surfactants at various concentrations as a skin penetration enhancer through the biomembrane of the shed skin of Naja kaouthia. Additionally, the enhancer mechanism(s) of each class of surfactants were evaluated using physical characterization techniques, such as scanning electron microscopy (SEM), attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectroscopy, and small and wide angle X-ray scattering (SWAXS). Our results showed that skin permeability increased with increasing concentrations of surfactants and the degree of increase was higher for the model hydrophilic permeant, deuterium dioxide (D(2)O), than the lipophilic permeant, ketoprofen (KP). Ionic surfactants, sodium lauryl sulfate (SLS) and cetyl trimethyl ammonium bromide (CTAB), demonstrated higher enhancement ability than the polyoxyethylene (20) sorbitan mono-oleate (Tween 80) non-ionic surfactant, which was consistent with the results from physical characterization studies. Increasing amounts of permeated drug resulted in an increase in membrane interactions. From our observations, it can be assumed that SLS and CTAB can be localized inside the biomembrane and thereby enhance drug permeation mainly through interactions with intercellular lipids in the stratum corneum (SC) and the creation of a perturbed microenvironment among lipid alkyl chains and polar head groups.

Effect of double-tailed surfactant architecture on the conformation, self-assembly, and processing in polypeptide-surfactant complexes.

Science.gov (United States)

Junnila, Susanna; Hanski, Sirkku; Oakley, Richard J; Nummelin, Sami; Ruokolainen, Janne; Faul, Charl F J; Ikkala, Olli

2009-10-12

This work describes the solid-state conformational and structural properties of self-assembled polypeptide-surfactant complexes with double-tailed surfactants. Poly(L-lysine) was complexed with three dialkyl esters of phosphoric acid (i.e., phosphodiester surfactants), where the surfactant tail branching and length was varied to tune the supramolecular architecture in a facile way. After complexation with the branched surfactant bis(2-ethylhexyl) phosphate in an aqueous solution, the polypeptide chains adopted an alpha-helical conformation. These rod-like helices self-assembled into cylindrical phases with the amorphous alkyl tails pointing outward. In complexes with dioctyl phosphate and didodecyl phosphate, which have two linear n-octyl or n-dodecyl tails, respectively, the polypeptide formed antiparallel beta-sheets separated by alkyl layers, resulting in well-ordered lamellar self-assemblies. By heating, it was possible to trigger a partial opening of the beta-sheets and disruption of the lamellar phase. After repeated heating/cooling, all of these complexes also showed a glass transition between 37 and 50 degrees C. Organic solvent treatment and plasticization by overstoichiometric amount of surfactant led to structure modification in poly(L-lysine)-dioctyl phosphate complexes, PLL(diC8)(x) (x = 1.0-3.0). Here, the alpha-helical PLL is surrounded by the surfactants and these bottle-brush-like chains self-assemble in a hexagonal cylindrical morphology. As x is increased, the materials are clearly plasticized and the degree of ordering is improved: The stiff alpha-helical backbones in a softened surfactant matrix give rise to thermotropic liquid-crystalline phases. The complexes were examined by Fourier transform infrared spectroscopy, small- and wide-angle X-ray scattering, transmission electron microscopy, differential scanning calorimetry, polarized optical microscopy, and circular dichroism.

Degradation of surfactants by sono-irradiation

International Nuclear Information System (INIS)

Ashokkumar, M.; Grieser, F.; Vinodgopal, K.

2000-01-01

Full text: The ultrasound induced decomposition of a commercially available polydisperse nonylphenol ethoxylate surfactant (Teric GN9) has been investigated. Nearly 90% mineralization and/or degradation into volatile products of the surfactant is achieved after sonication for 24 hours. Ultrasound has been found to be a useful tool to achieve a number of chemical processes. Linear and branched alkyl benzene sulfonates and alkyl nonylphenol ethoxylates are widely used surfactants which accumulated in the environment and contribute to a well-recognised pollution problem. We have investigated the use of ultrasound in the degradation of both types of surfactants with the aim of understanding the mechanism of degradation in order to optimise the decomposition process. In this presentation, we report on the sonochemical degradation of Teric GN9- polydisperse, a nonylphenol ethoxylate with an average of 9 ethylene oxide units. The ultrasound unit used for the degradation studies of the surfactant solutions was an Allied Signal (ELAC Nautik) RF generator and transducer with a plate diameter of 54.5 mm operated at 363 kHz in continuous wave mode at an intensity of 2 W/cm 2 . Ultrasound induced cavitation events generate primary radicals inside gas/vapour filled bubbles. Due to the extreme conditions (T ∼ 5000 K; P ∼ 100 atm) generated within the collapsing bubble, H and OH radicals are produced by the homolysis of water molecules, if water is the medium of sonication. These primary radicals attack the surfactant molecules adsorbed at the bubble/water interface. The initial rate of reaction of the surfactant was found to be dependent on the monomer concentration in solution below and above the critical micelle concentration of the surfactants. This result strongly suggests that the initial radical attack on the surfactants occurs at the cavitation bubble/solution interface, followed by oxidative decomposition and pyrolysis of volatile fragments of the surfactant within

Thermodynamic solution properties of pefloxacin mesylate and its interactions with organized assemblies of anionic surfactant, sodium dodecyl sulphate

International Nuclear Information System (INIS)

Usman, Muhammad; Rashid, Muhammad Abid; Mansha, Asim; Siddiq, Mohammad

2013-01-01

Graphical abstract: - Highlights: • Free energy of adsorption is more negative than free energy of micellization. • Micellization becomes more spontaneous at high temperature. • There is strong interaction between PFM and SDS. - Abstract: This manuscript reports the physicochemical behavior of antibiotic amphiphilic drug pefloxacin mesylate (PFM) and its interaction with anionic surfactant, sodium dodecyl sulfate (SDS). The data of surface tension and electrical conductivity are helpful to detect the CMC as well as to calculate surface parameters, i.e. surface pressure, π, surface excess concentration, Γ, area per molecule of drug and standard Gibbs free energy of adsorption, ΔG ads and thermodynamic parameters like standard free energy of micellization, ΔG m , standard enthalpy of micellization, ΔH m and standard entropy of micellization, ΔS m . The interaction of this drug with anionic surfactant, sodium dodecyl sulfate (SDS) was studied by electrical conductivity and UV/visible spectroscopy. This enabled us to compute the values of partition coefficient (K x ), free energy of partition, ΔG p , binding constant, K b , free energy of binding, ΔG b , number of drug molecules per micelle, n, and thermodynamic parameters of drug–surfactant interaction

Application of Sodium Ligno Sulphonate as Surfactant in Enhanced Oil Recovery and Its Feasibility Test for TPN 008 Oil

Science.gov (United States)

Prakoso, N. I.; Rochmadi; Purwono, S.

2018-04-01

One of enhanced oil recovery (EOR) methods is using surfactants to reduce the interfacial tension between the injected fluid and the oil in old reservoir. The most important principle in enhanced oil recovery process is the dynamic interaction of surfactants with crude oil. Sodium ligno sulphonate (SLS) is a commercial surfactant and already synthesized from palm solid waste by another researcher. This work aimed to apply SLS as a surfactant for EOR especially in TPN 008 oil from Pertamina Indonesia. In its application as an EOR’s surfactant, SLS shall be passed feasibility test like IFT, thermal stability, compatibility, filtration, molecular weight, density, viscosity and pH tests. The feasibility test is very important for a preliminary test prior to another advanced test. The results demonstrated that 1% SLS solution in formation water (TPN 008) had 0.254 mN/M IFT value and was also great in thermal stability, compatibility, filtration, molecular weight, viscosity and pH test.

Profile of irritant patch testing with detergents: sodium lauryl sulfate, sodium laureth sulfate and alkyl polyglucoside.

Science.gov (United States)

Löffler, H; Happle, R

2003-01-01

The cutaneous reaction to detergents follows distinct kinetic rules: the duration of application and the irritant concentration are of major importance. The aim of this study was to evaluate the differences in kinetics of skin reaction between the standard irritant sodium lauryl sulfate (SLS), and 2 modern detergents: sodium laureth sulfate (SLES) and alkyl polyglucoside (APG). We performed patch testing with SLS and SLES (or APG) at different concentrations (0.125, 0.25, 0.5, 1.0 and 2.0%) and with different exposure times (6, 12 and 24 h). Evaluation was conducted by measurement of transepidermal water loss (TEWL) and laser Doppler flowmetry (LD) 24 h, 7 and 10 days after patch removal. We found a pronounced reaction to SLS, and a far milder one to SLES. Even at the highest concentration the skin reaction to APG was hard to detect. During the regeneration period (day 3-10) SLS showed even at day 10 an increased TEWL at all concentrations tested. The irritation due to SLES was convincingly detectable only up to day 7, whereas the APG-tested skin areas showed no significant reaction even at day 3. These results demonstrate the improvement in reduction of skin irritation achieved by development of novel detergents.

Layer-by-Layer Assembly of Fluorine-Free Polyelectrolyte-Surfactant Complexes for the Fabrication of Self-Healing Superhydrophobic Films.

Science.gov (United States)

Wu, Mengchun; An, Ni; Li, Yang; Sun, Junqi

2016-11-29

Fluorine-free self-healing superhydrophobic films are of significance for practical applications because of their extended service life and cost-effective and eco-friendly preparation process. In this study, we report the fabrication of fluorine-free self-healing superhydrophobic films by layer-by-layer (LbL) assembly of poly(sodium 4-styrenesulfonate) (PSS)-1-octadecylamine (ODA) complexes (PSS-ODA) and poly(allylamine hydrochloride) (PAH)-sodium dodecyl sulfonate (SDS) (PAH-SDS) complexes. The wettability of the LbL-assembled PSS-ODA/PAH-SDS films depends on the film structure and can be tailored by changing the NaCl concentration in aqueous dispersions of PSS-ODA complexes and the number of film deposition cycles. The freshly prepared PSS-ODA/PAH-SDS film with micro- and nanoscaled hierarchical structures is hydrophilic and gradually changes to superhydrophobic in air because the polyelectrolyte-complexed ODA and SDS surfactants tend to migrate to the film surface to cover the film with hydrophobic alkyl chains to lower its surface energy. The large amount of ODA and SDS surfactants loaded in the superhydrophobic PSS-ODA/PAH-SDS films and the autonomic migration of these surfactants to the film surface endow the resultant superhydrophobic films with an excellent self-healing ability to restore the damaged superhydrophobicity. The self-healing superhydrophobic PSS-ODA/PAH-SDS films are mechanically robust and can be deposited on various flat and nonflat substrates. The LbL assembly of oppositely charged polyelectrolyte-surfactant complexes provides a new way for the fabrication of fluorine-free self-healing superhydrophobic films with satisfactory mechanical stability, enhanced reliability, and extended service life.

Interactions between Surfactants in Solution and Electrospun Protein Fibers: Effects on Release Behavior and Fiber Properties

DEFF Research Database (Denmark)

Boutrup Stephansen, Karen; García-Díaz, María; Jessen, Flemming

2016-01-01

, and drug delivery. In the present study, we present a systematic investigation of how surfactants and proteins, as physiologically relevant components, interact with insulin-loaded fish sarcoplasmic protein (FSP) electrospun fibers (FSP-Ins fibers) in solution and thereby affect fiber properties...... such as accessible surface hydrophilicity, physical stability, and release characteristics of an encapsulated drug. Interactions between insulin-loaded protein fibers and five anionic surfactants (sodium taurocholate, sodium taurodeoxycholate, sodium glycocholate, sodium glycodeoxycholate, and sodium dodecyl sulfate......), a cationic surfactant (benzalkonium chloride), and a neutral surfactant (Triton X-100) were studied. The anionic surfactants increased the insulin release in a concentration-dependent manner, whereas the neutral surfactant had no significant effect on the release. Interestingly, only minute amounts...

S-alkylation of soft scorpionates.

Science.gov (United States)

Rajasekharan-Nair, Rajeev; Moore, Dean; Chalmers, Kirsten; Wallace, Dawn; Diamond, Louise M; Darby, Lisa; Armstrong, David R; Reglinski, John; Spicer, Mark D

2013-02-11

The alkylation reactions of soft scorpionates are reported. The hydrotris(S-alkyl-methimazolyl)borate dications (alkyl = methyl, allyl, benzyl), which were prepared by the reaction of Tm(Me) anion and primary alkyl halides, have been isolated and structurally characterised. The reaction is, however, not universally successful. DFT analysis of these alkylation reactions (C=S versus B-H alkylation) indicates that the observed outcome is driven by kinetic factors. Extending the study to incorporate alternative imine thiones (mercaptobenzothiazole, bz; thiazoline, tz) led to the structural characterisation of di[aquo-μ-aquohydrotris(mercaptobenzothiazolyl)boratosodium], which contains sodium atoms in the κ(3)-S,S,S coordination mode. Alkylation of Na[Tbz] and Na[tzTtz] leads to decomposition resulting in the formation of the simple S-alkylated heterocycles. The analysis of the species involved in these reactions shows an inherent weakness in the B-N bond in soft scorpionates, which has implications for their use in more advanced chemistry. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Tuning the probe location on zwitterionic micellar system with variation of pH and addition of surfactants with different alkyl chains: solvent and rotational relaxation studies.

Science.gov (United States)

Banerjee, Chiranjib; Mandal, Sarthak; Ghosh, Surajit; Rao, Vishal Govind; Sarkar, Nilmoni

2012-09-13

In this manuscript, we have modulated the location of an anionic probe, Coumarin-343 (C-343) in a zwitterionic (N-hexadecyl-N,N-dimethylammonio-1-propanesulfonate (SB-16)) micellar system by three different approaches. The effect of addition of the surfactant sodium dodecyl sulfate (SDS) and the room temperature ionic liquid (RTIL), 1-ethyl-3-methylimidazolium octylsulfate (EmimOs) and N,N-dimethylethanol hexanoate (DAH), to the micellar solution has been studied. The effect of pH variation has been studied as well using solvent and rotational measurements. Migration of the anionic probe, C-343, from the palisade layer of SB-16 micelle to the bulk water has been observed to varying extents with the addition of SDS and EmimOs. The effect is much more pronounced in the presence of SDS and can be ascribed to the presence of the long alkyl (dodecyl) chain on SDS which can easily orient itself and fuse inside the SB-16 micelle and facilitate the observed migration of the probe molecule. This phenomenon is confirmed by faster solvation and rotational relaxation of the investigated probe molecule. The analogous fusion process is difficult in case of EmimOs and DAH because of their comparatively smaller alkyl (octyl and hexanoate) chain. However, the direction of C-343 migration is reversed with the decrease of pH of the SB-16 micellar medium. An increase in the average solvation and rotational relaxation time of the probe in acidic medium has been observed. Since experimental conditions are maintained such that the probe molecules and the zwitterionic SB-16 micelles remain oppositely charged, the observed results can be attributed to the increased electrostatic interaction (attractive) between them. Temperature dependent study also supports this finding.

Impact of model perfume molecules on the self-assembly of anionic surfactant sodium dodecyl 6-benzene sulfonate.

Science.gov (United States)

Bradbury, Robert; Penfold, Jeffrey; Thomas, Robert K; Tucker, Ian M; Petkov, Jordan T; Jones, Craig; Grillo, Isabelle

2013-03-12

The impact of two model perfumes with differing degrees of hydrophobicity/hydrophilicity, linalool (LL) and phenylethanol (PE), on the solution structure of anionic surfactant sodium dodecyl 6-benzene sulfonate, LAS-6, has been studied by small angle neutron scattering, SANS. For both types of perfume molecules, complex phase behavior is observed. The phase behavior depends upon the concentration, surfactant/perfume composition, and type of perfume. The more hydrophilic perfume PE promotes the formation of more highly curved structures. At relatively low surfactant concentrations, small globular micelles, L1, are formed. These become perfume droplets, L(sm), stabilized by the surfactant at much higher perfume solution compositions. At higher surfactant concentrations, the tendency of LAS-6 to form more planar structures is evident. The more hydrophobic linalool promotes the formation of more planar structures. Combined with the greater tendency of LAS-6 to form planar structures, this results in the planar structures dominating the phase behavior for the LAS-6/linalool mixtures. For the LAS-6/linalool mixture, the self-assembly is in the form of micelles only at the lowest surfactant and perfume concentrations. Over most of the concentration-composition space explored, the structures are predominantly lamellar, L(α), or vesicle, L(v), or in the form of a lamellar/micellar coexistence. At low and intermediate amounts of LL, a significantly different structure is observed, and the aggregates are in the form of small, relatively monodisperse vesicles (i.e., nanovesicles), L(sv).

Aerobic biodegradation of amphoteric amine-oxide-based surfactants: Effect of molecular structure, initial surfactant concentration and pH.

Science.gov (United States)

Ríos, Francisco; Lechuga, Manuela; Fernández-Serrano, Mercedes; Fernández-Arteaga, Alejandro

2017-03-01

The present study was designed to provide information regarding the effect of the molecular structure of amphoteric amine-oxide-based surfactants and the initial surfactant concentration on their ultimate biodegradation. Moreover, given this parameter's pH-dependence, the effect of pH was also investigated. Three amine-oxide-based surfactants with structural differences in their hydrophobic alkyl chain were tested: Lauramine oxide (AO-R 12 ), Myristamine oxide (AO-R 14 ) and Cocamidopropylamine oxide (AO-Cocoamido). We studied the ultimate biodegradation using the Modified OECD Screening Test at initial surfactant concentrations ranged from 5 to 75 mg L -1 and at pH levels from 5 to 7.4. The results demonstrate that at pH 7.4, amine-oxide-based surfactants are readily biodegradable. In this study, we concluded that ω-oxidation can be assumed to be the main biodegradation pathway of amine-oxides and that differences in the biodegradability between them can be explained by the presence of an amide group in the alkyl chain of AO-Cocoamido; the CN fission of the amide group slows down their mineralization process. In addition, the increase in the concentration of the surfactant from 5 to 75 mg L -1 resulted in an increase in the final biodegradation of AO-R 12 and AO-R 14 . However, in the case of AO-Cocoamido, a clear relationship between the concentration and biodegradation cannot be stated. Conversely, the biodegradability of AO-R 12 and AO-R 14 was considerably lower in an acid condition than at a pH of 7.4, whereas AO-Cocoamido reached similar percentages in acid conditions and at a neutral pH. However, microorganisms required more time to acclimate. Copyright © 2016 Elsevier Ltd. All rights reserved.

Effect of selected non-ionic surfactants on the flow behavior of aqueous veegum suspensions.

Science.gov (United States)

Kennedy, Ross A; Kennedy, Michelle L

2007-03-30

The aim of this work was to investigate the influence of some non-ionic surfactants, Tween 80 and Brij 98, on the viscosity and flow behavior of a commercial montmorillonite clay, Veegum Granules. The effect of different concentrations of the surfactants on the shear stress-shear rate rheograms of hydrated concentrated clay suspensions was determined by shear viscometry. The addition of either surfactant increased the plastic viscosity and the yield stress of the suspensions. Furthermore, both surfactants altered the thixotropy of the suspensions to an extent that depended on both the surfactant concentration and the time of equilibration of the surfactant and Veegum. Brij 98 had a greater and more rapid effect. It is proposed that the surfactant polar head-groups anchor at the tetrahedral sheet surface, leaving the alkyl chains extending away from the edges and faces. Consequently, the alkyl chains undergo hydrophobic interactions that facilitate the association between the platelets and increase the physical structure within the suspension. Stereochemical differences between the polar groups may lead to differences in the way the surfactants associate with the tetrahedral sheet and hence their ultimate effect on the rheological behavior. There is a significant interaction between these surfactants and montmorillonite clays, and the rheological changes that occur could have a major impact on any pharmaceutical formulation that uses these ingredients.

Cu sbnd Al sbnd Fe layered double hydroxides with CO32- and anionic surfactants with different alkyl chains in the interlayer

Science.gov (United States)

Trujillano, Raquel; Holgado, María Jesús; González, José Luis; Rives, Vicente

2005-08-01

Layered double hydroxides (LDHs), with the hydrotalcite-like structure containing Cu(II), Al(III) and Fe(III) in the layers, and different alkyl sulfonates in the interlayer, have been prepared and characterized by powder X-ray diffraction, FT-IR spectroscopy, differential thermal analysis and thermogravimetric analysis. Pure crystalline phases have been obtained in all cases. Upon heating, combustion of the organic chain takes place at lower temperature than the corresponding sodium salts.

Thermodynamics on the micellization of various pure and mixed surfactants: Effects of head- and tail-groups

International Nuclear Information System (INIS)

Lee, Nam-Min; Lee, Byung-Hwan

2016-01-01

Highlights: • The values of critical micelle concentration of various pure and mixed surfactants are measured. • Thermodynamic parameters’ values are calculated to analyze the effects of head- and tail-groups on the micellization. • All the thermodynamic parameters’ values are decreasing with the increase of temperature. • The thermodynamic parameters’ values are depending severely on the chain length of alkyl group. - Abstract: The values of critical micelle concentration (CMC) for the micellization of various pure and mixed surfactants are determined by the UV–Vis spectrophotometric method. And the effects of temperature on the CMC values have been measured and thermodynamic parameters’ values are calculated to analyse the effects of head- and tail-groups on the micellization of surfactant molecules. The results show that the values of ΔG"o are negative and those of ΔS"o are positive for the micellization of all the surfactants within the measured temperature range. But the values of ΔH"o are positive or negative, depending on the kinds of surfactants. All these thermodynamic parameters’ values are decreasing together with the increase of temperature for all the surfactants. And these thermodynamic parameters’ values are depending severely on the chain length of alkyl group also as much as on the head-groups of surfactant molecules.

Nanoparticle-enabled delivery of surfactants in porous media.

Science.gov (United States)

Nourafkan, Ehsan; Hu, Zhongliang; Wen, Dongsheng

2018-06-01

The adsorption of surfactants on the reservoir rocks surface is a serious issue in many energy and environment related areas. Learning from the concept of drug delivery in the nano-medicine field, this work proposes and validates the concept of using nanoparticles to deliver a mixture of surfactants into a porous medium. TiO 2 nanoparticles (NPs) are used as carriers for a blend of surfactants mixtures including anionic alkyl aryl sulfonic acid (AAS) and nonionic alcohol ethoxylated (EA) at the optimum salinity and composition conditions. The transport of NPs through a core sample of crushed sandstone grains and the adsorption of surfactants are evaluated. By using TiO 2 NPs, the adsorption of surfactant molecules can be significantly reduced, i.e. half of the initial adsorption value. The level of surfactant adsorption reduction is related to the NPs transport capability through the porous medium. An application study shows that comparing to surfactant flooding alone, the total oil recovery can be increased by 7.81% of original oil in place (OOIP) by using nanoparticle bonded surfactants. Such work shows the promise of NP as an effective surfactant carrier for sandstone reservoirs, which could have many potential applications in enhanced oil recovery (EOR) and environmental remediation. Copyright © 2018 Elsevier Inc. All rights reserved.

Photoisomerization of merocyanine 540 in polymer-surfactant ...

Indian Academy of Sciences (India)

Photoisomerization of merocyanine 540 (MC540) in a polymer-surfactant aggregate is studied using picosecond time resolved emission spectroscopy. The aggregate consists of the polymer, poly(vinylpyrrolidone) (PVP) and the surfactant, sodium dodecyl sulphate (SDS). With increase in the concentration of SDS in an ...

Preparation and physicochemical properties of surfactant-free emulsions using electrolytic-reduction ion water containing lithium magnesium sodium silicate.

Science.gov (United States)

Okajima, Masahiro; Wada, Yuko; Hosoya, Takashi; Hino, Fumio; Kitahara, Yoshiyasu; Shimokawa, Ken-ichi; Ishii, Fumiyoshi

2013-04-01

Surfactant-free emulsions by adding jojoba oil, squalane, olive oil, or glyceryl trioctanoate (medium chain fatty acid triglycerides, MCT) to electrolytic-reduction ion water containing lithium magnesium sodium silicate (GE-100) were prepared, and their physiochemical properties (thixotropy, zeta potential, and mean particle diameter) were evaluated. At an oil concentration of 10%, the zeta potential was ‒22.3 ‒ ‒26.8 mV, showing no marked differences among the emulsions of various types of oil, but the mean particle diameters in the olive oil emulsion (327 nm) and MCT emulsion (295 nm) were smaller than those in the other oil emulsions (452-471 nm). In addition, measurement of the hysteresis loop area of each type of emulsion revealed extremely high thixotropy of the emulsion containing MCT at a low concentration and the olive emulsion. Based on these results, since surfactants and antiseptic agents markedly damage sensitive skin tissue such as that with atopic dermatitis, surfactant- and antiseptic-free emulsions are expected to be new bases for drugs for external use.

Study of conformation and dynamic of surfactant molecules in graphite oxide via NMR

Energy Technology Data Exchange (ETDEWEB)

Ai, X.Q. [Jiangsu Second Normal University, College of Physics and Electronic Engineering, Nanjing (China); Ma, L.G. [Nanjing Xiaozhuang University, School of Electronic Engineering, Nanjing (China)

2016-08-15

The conformation and dynamic of surfactant in graphite oxide (GO) was investigated by solid-state {sup 13}C magic-angle-spinning NMR and {sup 1}H-{sup 13}C cross-polarization/magic-angle-spinning NMR spectra. The conformation ordering of the alkyl chains in the confined system shows strong dependence on its orientation. While the alkyl chains parallel to the GO layer in lateral monolayer arrangement are in gauche conformation in addition to a small amount of all-trans conformation, those with orientation radiating away from the GO in paraffin bilayer arrangement is in all-trans conformation in addition to some gauche conformation even though high-order diffraction peaks appears. NMR results suggest that the least mobile segment is located at the GO-surfactant interface corresponding to the N-methylene group. Further from it, the mobility of the alkyl chain increases. The terminal methyl and N-methyl carbon groups have the highest mobile. The chains in all-trans conformational state are characterized as more rigid than chains with gauche conformation; each segment of the confined alkyl chains with the lateral monolayer arrangement exhibits less mobility as compared to that with the paraffin bilayer arrangement. (orig.)

Integration of chemical scrubber with sodium hypochlorite and surfactant for removal of hydrocarbons in cooking oil fume

International Nuclear Information System (INIS)

Cheng, Hsin-Han; Hsieh, Chu-Chin

2010-01-01

There are many types of technologies to control cooking oil fumes (COFs), but current typical technologies, such as electrostatic precipitator, conventional scrubber, catalyst, or condenser, are unable to efficiently remove the odorous materials present in COFs which are the primary cause of odor-complaint cases. There is also a lack of information about using sodium hypochlorite (NaOCl) and surfactants to remove contaminants in COFs, and previous studies lack on-site investigations in restaurants. This study presents a chemical scrubber integrated with an automatic control system (ACS) to treat hydrocarbons (HCs) in COFs, and to monitor non-methane HCs (NMHC) and odor as indicators for its efficiency evaluation. The chemical scrubber effectively treats hydrophobic substances in COFs by combining surfactant and NaOCl under optimal operational conditions with NHMC removal efficiency as high as 85%. The mass transfer coefficient (K L a) of NMHC was enhanced by 50% under the NaOCl and surfactant conditions, as compared to typical wet scrubber. Further, this study establishes the fuzzy equations of the ACS, including the relationship between the removal efficiency and K L a, liquid/gas ratio, pH and C NaOCl .

Integration of chemical scrubber with sodium hypochlorite and surfactant for removal of hydrocarbons in cooking oil fume

Energy Technology Data Exchange (ETDEWEB)

Cheng, Hsin-Han [Graduate School of Engineering Science and Technology, National Yunlin University of Science and Technology, Touliu, Yunlin, Taiwan (China); Hsieh, Chu-Chin, E-mail: hsiehcc@yuntech.edu.tw [Department of Environmental and Safety Engineering, National Yunlin University of Science and Technology, Touliu, Yunlin, Taiwan (China)

2010-10-15

There are many types of technologies to control cooking oil fumes (COFs), but current typical technologies, such as electrostatic precipitator, conventional scrubber, catalyst, or condenser, are unable to efficiently remove the odorous materials present in COFs which are the primary cause of odor-complaint cases. There is also a lack of information about using sodium hypochlorite (NaOCl) and surfactants to remove contaminants in COFs, and previous studies lack on-site investigations in restaurants. This study presents a chemical scrubber integrated with an automatic control system (ACS) to treat hydrocarbons (HCs) in COFs, and to monitor non-methane HCs (NMHC) and odor as indicators for its efficiency evaluation. The chemical scrubber effectively treats hydrophobic substances in COFs by combining surfactant and NaOCl under optimal operational conditions with NHMC removal efficiency as high as 85%. The mass transfer coefficient (K{sub L}a) of NMHC was enhanced by 50% under the NaOCl and surfactant conditions, as compared to typical wet scrubber. Further, this study establishes the fuzzy equations of the ACS, including the relationship between the removal efficiency and K{sub L}a, liquid/gas ratio, pH and C{sub NaOCl}.

Adsorption at air-water and oil-water interfaces and self-assembly in aqueous solution of ethoxylated polysorbate nonionic surfactants.

Science.gov (United States)

Penfold, Jeffrey; Thomas, Robert K; Li, Peixun X; Petkov, Jordan T; Tucker, Ian; Webster, John R P; Terry, Ann E

2015-03-17

The Tween nonionic surfactants are ethoxylated sorbitan esters, which have 20 ethylene oxide groups attached to the sorbitan headgroup and a single alkyl chain, lauryl, palmityl, stearyl, or oleyl. They are an important class of surfactants that are extensively used in emulsion and foam stabilization and in applications associated with foods, cosmetics and pharmaceuticals. A range of ethoxylated polysorbate surfactants, with differing degrees of ethoxylation from 3 to 50 ethylene oxide groups, have been synthesized and characterized by neutron reflection, small-angle neutron scattering, and surface tension. In conjunction with different alkyl chain groups, this provides the opportunity to modify their surface properties, their self-assembly in solution, and their interaction with macromolecules, such as proteins. Adsorption at the air-water and oil-water interfaces and solution self-assembly of the range of ethoxylated polysorbate surfactants synthesized are presented and discussed.

Binding of alkylpyridinium chloride surfactants to sodium polystyrene sulfonate

NARCIS (Netherlands)

Ishiguro, M.; Koopal, L.K.

2009-01-01

Binding of cationic surfactants to anionic polymers is well studied. However, the surfactant binding characteristics at very low concentration near the start of binding and at high concentration, where charge compensation may Occur. are less well known. Therefore, the binding characteristics of

Entropy of adsorption of mixed surfactants from solutions onto the air/water interface

Science.gov (United States)

Chen, L.-W.; Chen, J.-H.; Zhou, N.-F.

1995-01-01

The partial molar entropy change for mixed surfactant molecules adsorbed from solution at the air/water interface has been investigated by surface thermodynamics based upon the experimental surface tension isotherms at various temperatures. Results for different surfactant mixtures of sodium dodecyl sulfate and sodium tetradecyl sulfate, decylpyridinium chloride and sodium alkylsulfonates have shown that the partial molar entropy changes for adsorption of the mixed surfactants were generally negative and decreased with increasing adsorption to a minimum near the maximum adsorption and then increased abruptly. The entropy decrease can be explained by the adsorption-orientation of surfactant molecules in the adsorbed monolayer and the abrupt entropy increase at the maximum adsorption is possible due to the strong repulsion between the adsorbed molecules.

DETERMINATION OF ALKYLATED & SULFONATED DIPHENYL OXIDE SULFACTANT BY HIGH PERFORMANCE LIQUID CHROMATOGRAPHY

Science.gov (United States)

Methods for the determination of the anionic surfactant Dowfax 8390 are described. Dowfax is a complex mixture of various alkylated and sulfonated diphenyl oxides. The primary component of Dowfax is monoalkylated disulfonated diphenyl oxide (MADS). This work uses ion pairing chro...

The interactions between ionic surfactants and phosphatidylcholine vesicles: Conductometry

Science.gov (United States)

Tsao, Heng-Kwong; Tseng, Wen Liang

2001-11-01

The interaction between ionic surfactants and phosphatidylcholine vesicles, which are prepared without addition of buffer and salt, is investigated by conductivity measurements. On the basis of the vesicle acting as a trap of charge carriers, the bilayer/aqueous phase partition coefficient K and the surfactant/lipid molar ratio Re of nine surfactants are determined. The thermodynamic consistency is satisfied by the measured parameters. The effects of the alkyl chain length (C10-C16) and ionic head group are then studied. The inverse partition coefficient K-1 is linearly related to the critical micelle concentration. The solubilizing ability Reb is a consequence of the competition between the surfactant incorporation into the bilayer and the formation of micelles. Consequently, the K parameter rises whereas the Reb parameter declines as the chain length is increased. The influence due to addition of salt is also discussed.

Maillard Conjugation of Sodium Alginate to Whey Protein for Enhanced Resistance to Surfactant-Induced Competitive Displacement from Air-Water Interfaces.

Science.gov (United States)

Cai, Bingqing; Saito, Anna; Ikeda, Shinya

2018-01-24

Whey protein adsorbed to an interface forms a viscoelastic interfacial film but is displaced competitively from the interface by a small-molecule surfactant added afterward. The present study evaluated the impact of the covalent conjugation of high- or low-molecular-weight sodium alginate (HA or LA) to whey protein isolate (WPI) via the Maillard reaction on the ability of whey protein to resist surfactant-induced competitive displacement from the air-water interface. Surfactant added after the pre-adsorption of conjugate to the interface increased surface pressure. At a given surface pressure, the WPI-LA conjugate showed a significantly higher interfacial area coverage and lower interfacial film thickness compared to those of the WPI-HA conjugate or unconjugated WPI. The addition of LA to the aqueous phase had little effect on the interfacial area and thickness of pre-adsorbed WPI. These results suggest the importance of the molecular weight of the polysaccharide moiety in determining interfacial properties of whey protein-alginate conjugates.

Silica micro- and nanoparticles reduce the toxicity of surfactant solutions.

Science.gov (United States)

Ríos, Francisco; Fernández-Arteaga, Alejandro; Fernández-Serrano, Mercedes; Jurado, Encarnación; Lechuga, Manuela

2018-04-20

In this work, the toxicity of hydrophilic fumed silica micro- and nanoparticles of various sizes (7 nm, 12 nm, and 50 μm) was evaluated using the luminescent bacteria Vibrio fischeri. In addition, the toxicity of an anionic surfactant solution (ether carboxylic acid), a nonionic surfactant solution (alkyl polyglucoside), and a binary (1:1) mixture of these solutions all containing these silica particles was evaluated. Furthermore, this work discusses the adsorption of surfactants onto particle surfaces and evaluates the effects of silica particles on the surface tension and critical micellar concentration (CMC) of these anionic and nonionic surfactants. It was determined that silica particles can be considered as non-toxic and that silica particles reduce the toxicity of surfactant solutions. Nevertheless, the toxicity reduction depends on the ionic character of the surfactants. Differences can be explained by the different adsorption behavior of surfactants onto the particle surface, which is weaker for nonionic surfactants than for anionic surfactants. Regarding the effects on surface tension, it was found that silica particles increased the surface activity of anionic surfactants and considerably reduced their CMC, whereas in the case of nonionic surfactants, the effects were reversed. Copyright © 2018 Elsevier B.V. All rights reserved.

Adsorption of dissymmetric cationic gemini surfactants at silica/water interface

Science.gov (United States)

Sun, Yuhai; Feng, Yujun; Dong, Hongwei; Chen, Zhi

2007-05-01

Adsorption of a series of cationic gemini surfactants 12-2- m ( m = 8, 12, 16) on the surface of silica was investigated. The critical micelle concentrations, cmcs, of cationic gemini surfactants in the initial solutions and in the supernatants were measured by conductometry and tensiometer. The changes in cmc values indicate that the ion exchanges take place between polar groups of gemini surfactants adsorbed and ions bound on the surface of silica. The adsorption isotherms of cationic gemini surfactants were obtained by a solution depletion method. Based on the driving force, the adsorption includes two steps, one of which is ion exchange, and the other is hydrophobic interaction. In each step, the tendency of surfactant molecules in the solution to form aggregates or to be adsorbed on the silica varies with their structures. The maximum adsorption amount of gemini surfactants on the silica, τmax, decreases as increasing in the length of one alkyl chain, m, from 8, 12 to 16. So the results show that the adsorption behaviors of gemini surfactants are closely related to the dissymmetry of gemini molecules.

Synthesis and properties evaluation of sulfobetaine surfactant with double hydroxyl

Science.gov (United States)

Zhou, Ming; Luo, Gang; Zhang, Ze; Li, Sisi; Wang, Chengwen

2017-09-01

A series of sulfobetaine surfactants {N-[(3-alkoxy-2-hydroxyl)propoxy] ethyl-N,N-dimethyl-N-(2-hydroxyl)propyl sulfonate} ammonium chloride were synthesized with raw materials containing linear saturated alcohol, N,N-dimethylethanolamine, sodium 3-chloro-2-hydroxyl propane sulfonic acid and epichlorohydrin. The molecule structures of sulfobetaine surfactants were characterized by FTIR, 1HNMR and elemental analysis. Surface tension measurements can provide us information about the surface tension at the CMC (γCMC), pC20, Γmax and Amin. The pC20 values of sulfobetaine surfactants increase with the hydrophobic chain length increasing. Amin values of the surfactants decrease with increasing hydrophobic chain length from 10 to 14. The critical micelle concentration (CMC) and surface tension (γCMC) values of the sulfobetaine surfactants decrease with increasing hydrophobic chain length from 10 to 16. The lipophilicity of surfactant was enhanced with the increase of the carbon chain, however, the ability of anti-hard water was weakened. The minimum oil/water interfacial tension of four kinds of sulfobetaine surfactants is 10-2-10-3 mN/m magnitude, which indicates that the synthesized bis-hydroxy sulfobetaine surfactants have a great ability to reduce interfacial tension in the surfactant flooding system. The surface tension (γCMC) values of synthesized surfactants were lower compared with conventional anionic surfactant sodium dodecyl sulfonate.

Biodegradation of surfactant bearing wastes

International Nuclear Information System (INIS)

Chitra, S.; Chandran, S.; Sasidhar, P.; Lal, K.B.; Amalraj, R.V.

1991-01-01

In nuclear industry, during decontamination of protective wears and contaminated materials, detergents are employed to bring down the level of radioactive contamination within safe limits. However, the surfactant present in these wastes interferes in the chemical treatment process, reducing the decontamination factor. Biodegradation is an efficient and ecologically safe method for surfactant removal. A surfactant degrading culture was isolated and inoculated separately into simulated effluents containing 1% yeast extract and 5-100 ppm sodium lauryl sulphate (SLS) and 1% yeast extract and 5-100 ppm of commercial detergent respectively. The growth of the bacterial culture and the degradation characteristics of the surfactant in the above effluents were monitored under both dynamic and static conditions. (author). 6 refs., 6 figs., 1 tab

Role of adsorbed surfactant in the reaction of aryl diazonium salts with single-walled carbon nanotubes.

Science.gov (United States)

Hilmer, Andrew J; McNicholas, Thomas P; Lin, Shangchao; Zhang, Jingqing; Wang, Qing Hua; Mendenhall, Jonathan D; Song, Changsik; Heller, Daniel A; Barone, Paul W; Blankschtein, Daniel; Strano, Michael S

2012-01-17

Because covalent chemistry can diminish the optical and electronic properties of single-walled carbon nanotubes (SWCNTs), there is significant interest in developing methods of controllably functionalizing the nanotube sidewall. To date, most attempts at obtaining such control have focused on reaction stoichiometry or strength of oxidative treatment. Here, we examine the role of surfactants in the chemical modification of single-walled carbon nanotubes with aryl diazonium salts. The adsorbed surfactant layer is shown to affect the diazonium derivatization of carbon nanotubes in several ways, including electrostatic attraction or repulsion, steric exclusion, and direct chemical modification of the diazonium reactant. Electrostatic effects are most pronounced in the cases of anionic sodium dodecyl sulfate and cationic cetyltrimethylammonium bromide, where differences in surfactant charge can significantly affect the ability of the diazonium ion to access the SWCNT surface. For bile salt surfactants, with the exception of sodium cholate, we find that the surfactant wraps tightly enough such that exclusion effects are dominant. Here, sodium taurocholate exhibits almost no reactivity under the explored reaction conditions, while for sodium deoxycholate and sodium taurodeoxycholate, we show that the greatest extent of reaction is observed among a small population of nanotube species, with diameters between 0.88 and 0.92 nm. The anomalous reaction of nanotubes in this diameter range seems to imply that the surfactant is less effective at coating these species, resulting in a reduced surface coverage on the nanotube. Contrary to the other bile salts studied, sodium cholate enables high selectivity toward metallic species and small band gap semiconductors, which is attributed to surfactant-diazonium coupling to form highly reactive diazoesters. Further, it is found that the rigidity of anionic surfactants can significantly influence the ability of the surfactant layer to

FLOTATION DE-INKING OF 50% ONP/ 50% OMG RECOVERED PAPERS MIXTURES USING NONIONIC SURFACTANT, SOAP, AND SURFACTANT/SOAP BLENDS

Directory of Open Access Journals (Sweden)

Jeremy Allix

2010-11-01

Full Text Available A laboratory flotation column equipped with Venturi aerators and an adjustable froth removal system was used to study the effect of calcium soap and a mixture of calcium soap/alkyl phenol ethoxylate surfactant on ink and fibres transfer during flotation de-inking of a 50% old newprint (ONP / 50% old magazines (OMG recovered papers mixture. Mass transport phenomena determining the yield of the flotation process were interpreted using model equations describing particle removal in terms of flotation, entrainment, and drainage in the froth. A decrease in the ink and mineral fillers flotation rate constant, drainage through the froth, and in fibre entrainment was observed when increasing the surfactant concentration. These trends were consistent with the typical dispersing action of the studied nonionic surfactant. An opposite effect on ink and fillers was observed when using calcium soap alone, and the increase in the flotation rate constant and drainage through the froth were consistent with the collecting and defoaming action of the calcium soap. Moreover, fibre entrainment decreased when increasing the soap concentration. The study of the surfactant/soap mixture highlighted the absence of synergy between the calcium soap and the surfactant.

Degradation of surfactant-modified montmorillonites in HCl

International Nuclear Information System (INIS)

Madejová, Jana; Pálková, Helena; Jankovič, Ľuboš

2012-01-01

The effect of surfactant size on the extent of montmorillonites decomposition in HCl was investigated. Na-SAz montmorillonite and tetraalkylammonium salts of alkyl-chains length increasing from methyl- Me 4 N to pentyl- Pe 4 N were used for organo-montmorillonites preparation. Decreasing intensity of d 001 diffraction proved destruction of montmorillonite structure connected with gradual surfactant release. A shift of the SiO stretching band to 1097 cm −1 confirmed formation of amorphous silica phase. A new band near 7315 cm −1 corresponding to SiOH overtone revealed creation of protonated silica. This band was observed in the spectra of all acid-treated samples, also in those with minor decomposition of the structure. The size of the cations significantly affected decomposition of montmorillonites in HCl. The less stable were Na-SAz and Me 4 N-SAz in which the content of octahedral atoms dropped to ∼5% of their original values upon 8 h treatments. Et 4 N-SAz and Pr 4 N-SAz were slightly more resistant mainly at short times. Bu 4 N-SAz and Pe 4 N-SAz showed the least structural modifications, only 50% and 35% of octahedral atoms, respectively, were released into solution within 8 h treatments. This observation proves that bulky alkylammonium cations covering the inner and outer surfaces of montmorillonite prevent effectively the access of protons to the layers protecting the mineral from degradation in the acid. - Highlights: ► Hybrid materials were prepared from montmorillonite and alkylammonium cations with short alkyl chains. ► The effect of surfactant on organo-montmorillonites dissolution in HCl was studied. ► With increasing size of cation the extent of montmorillonite decomposition decreased. ► Bulky surfactants prevent the access of protons to the layers and thus protect montmorillonite from degradation.

Surfactant loss control in chemical flooding: Spectroscopic and calorimetric study of adsorption and precipitation on reservoir minerals. Annual report, September 30, 1992--September 30, 1993

Energy Technology Data Exchange (ETDEWEB)

Somasundaran, P.

1994-07-01

The aim of this research project is to investigate mechanisms underlying adsorption and surface precipitation of flooding surfactants on reservoir minerals. Effects of surfactant structure, surfactant combinations, various inorganic and polymeric species, and solids mineralogy will be determined. A multi-pronged approach consisting of micro & nano spectroscopy, microcalorimetry, electrokinetics, surface tension and wettability; is used in this study. The results obtained should help in controlling surfactant loss in chemical flooding and in developing optimum structures and conditions for efficient chemical flooding processes. During the first year of this three year contract, adsorption of single surfactants and select surfactant mixtures was studied at the solid-liquid and gas-liquid interfaces. Surfactants studied include alkyl xylene sulfonates, polyethoxylated alkyl phenols, octaethylene glycol mono n-decyl ether, and tetradecyl trimethyl ammonium chloride. Adsorption of surfactant mixtures of varying composition was also investigated. The microstructure of the adsorbed layer was characterized using fluorescence spectroscopy. Changes interfacial properties such as wettability, electrokinetics and stability of reservoir minerals were correlated with the amount of reagent adsorbed. Strong effects of the structure of the surfactant and position of functional groups were revealed.

Polyelectrolyte surfactant aggregates and their deposition on macroscopic surfaces

International Nuclear Information System (INIS)

Voisin, David

2002-01-01

cationically modified guar gums (of varying charge density) with two anionic surfactants: sodium lauryl (or dodecyl) ether sulfate [SLES] and sodium dodecyl sulfate [SDS], for various concentrations of the polyelectrolyte and added sodium chloride, at room temperature. The addition of sodium chloride has only a minor net effect on the CFC, but increases the CSC significantly. The interactions between the cationic polyelectrolyte and the surfactant have been studied in the one-phase regions, i.e. below the CFC and above the CSC, using different techniques. Surface tension, electrophoresis, light scattering and viscosimetry have been employed. In the two-phase region, the sedimented floe phase has been analysed and the flocculation has been investigated. Rheology of the floe phase has been studied, after a mild compression by centrifugation. The initial rate of flocculation has been determined, using stop-flow equipment. The growth and the structure of the flocs have been investigated by light scattering. The open-network flocs of polyelectrolyte-surfactant particles grow to ∼10's μm in size, prior to their eventual settling out. Other colloidal particles can be trapped within these large flocs, and the flocs can be used to transport these particles to a macroscopic surface. The deposition and the removal of such composite flocs on glass surfaces, under flow, have been studied using a flow cell device coupled with an optical microscope. Scanning electron microscopy and atomic force microscopy have also been employed. (author)

Biodegradation of the anionic surfactant sodium dodecyl sulfate by local bacterial isolate

International Nuclear Information System (INIS)

Ibrahim, H.M.M.; NoorEl-Din, M.R.

2011-01-01

Anionic surfactants, e.g., sodium dodecyl sulfate (SDS), as a main components in the detergent and cosmetic industries, contribute significantly to the pollution profile of sewage and wastewaters of all kinds. The purpose of this study was to isolate local SDS degrading bacteria. Screening was carried out by the conventional enrichment culture technique. One bacterial isolate was obtained; this isolate was primarily defined as gram-negative rods . It was capable of degrading 100% of 1000 and 2000 mg/l of SDS after 6 days of incubation. The isolate exhibited maximum growth at SDS concentration 4000 mg/I, but it was significantly decreased at higher concentration (16000 mg/I).All the carbon sources being tested repressed the degradation ability. Sodium nitrate at concentration of 2.0 g/I was the best nitrogen source for growth and SDS biodegradation, it enhanced the degradation of 3000 mg/I SDS by 95%,i.e., by 32% upon the control (broth medium containing NH 4 Cl). SDS degradation by the bacterium was optimum at initial ph 8.5, incubation temperature 35 degree C, and inoculum size 2% (v/v). Under the optimized conditions, almost 98% of initial SDS concentration (4000 mg/l) was degraded after 120 h of incubation. Gamma irradiation did not improve the biodegradation ability of this bacterial isolate.

The role of electrolyte and polyelectrolyte on the adsorption of the anionic surfactant, sodium dodecylbenzenesulfonate, at the air-water interface.

Science.gov (United States)

Zhang, X L; Taylor, D J F; Thomas, R K; Penfold, J

2011-04-15

The role of the polyelectrolyte, poly(ethyleneimine), PEI, and the electrolytes NaCl and CaCl(2), on the adsorption of the anionic surfactant, sodium dodecylbenzenesulfonate, LAS, at the air-water interface have been investigated by neutron reflectivity and surface tension. The surface tension data for the PEI/LAS mixtures are substantially affected by pH and the addition of electrolyte, and are consistent with a strong adsorption of surface polymer/surfactant complexes down to relatively low surfactant concentrations. The effects are most pronounced at high pH, and this is confirmed by the adsorption data obtained directly from neutron reflectivity. However, the effects of the addition of PEI and electrolyte on the LAS adsorption are not as pronounced as previously reported for PEI/SDS mixtures. This is attributed primarily to the steric hindrance of the LAS phenyl group resulting in a reduction in the ion-dipole attraction between the LAS sulfonate and amine groups that dominates the interaction at high pH. Copyright © 2011 Elsevier Inc. All rights reserved.

Surfactant sodium lauryl sulfate enhances skin vaccination: molecular characterization via a novel technique using ultrafiltration capillaries and mass spectrometric proteomics.

Science.gov (United States)

Huang, Chun-Ming; Wang, Chao-Cheng; Kawai, Mikako; Barnes, Stephen; Elmets, Craig A

2006-03-01

The skin is a highly accessible organ and thus provides an attractive immune environment for cost-effective, simple, and needle-free delivery of vaccines and immunomodulators. In this study, we pretreated mouse skin with an anionic surfactant, sodium lauryl sulfate (SLS), for a short period of time (10 min) followed by epicutaneous vaccination with hen egg lysozyme antigen. We demonstrated for the first time that pretreatment of skin with surfactant SLS significantly enhances the production of antibody to hen egg lysozyme. Short term pretreatment with SLS disorganized the stratum corneum, extracted partial lamellar lipids, induced the maturation of Langerhans cells, and did not result in epidermis thickening. To reveal the mechanism underlying these changes, particularly at the molecular level, we used a novel proteomic technique using ultrafiltration capillaries and mass spectrometry to identify in vivo proteins/peptides secreted in the SLS-pretreated skin. Two secretory proteins, named as calcium-binding protein S100A9 and thymosin beta4, were identified by this novel technique. These two proteins thus may provide new insight into the enhancing effect of surfactants on skin vaccination.

NMR study of the dynamics of cationic gemini surfactant 14-2-14 in mixed solutions with conventional surfactants.

Science.gov (United States)

Jiang, Yan; Lu, Xing-Yu; Chen, Hong; Mao, Shi-Zhen; Liu, Mai-Li; Luo, Ping-Ya; Du, You-Ru

2009-06-18

Three kinds of conventional surfactants, namely, two nonionic surfactants [polyethylene glycol (23) lauryl ether (Brij-35) and Triton X-100 (TX-100)], one cationic surfactant [n-tetradecyltrimethyl ammonium bromide (TTAB)], and an anionic surfactant [sodium n-dodecyl sulfate (SDS)}, were mixed into the quaternary ammonium gemini surfactant [C(14)H(29)N(+)(CH(3))(2)](2)(CH(2))(2).2Br(-) (14-2-14) in aqueous solution. The exchange rate constants between 14-2-14 molecules in the mixed micelles and those in the bulk solution were detected using two nuclear magnetic resonance (NMR) methods: one-dimensional (1D) line shape analysis and two-dimensional (2D) exchange spectroscopy (EXSY). The results obtained from these two methods were consistent. Both showed that mixing a nonionic conventional surfactant, either Brij-35 or TX-100, enhanced the exchange process between the 14-2-14 molecules in the mixed micelles and those in the bulk solution. In contrast, the anionic surfactant SDS and the cationic surfactant TTAB slowed the process slightly.

Adsorption of hydroxamate siderophores and EDTA on goethite in the presence of the surfactant sodium dodecyl sulfate

Directory of Open Access Journals (Sweden)

Xu Jide

2009-06-01

Full Text Available Abstract Siderophore-promoted iron acquisition by microorganisms usually occurs in the presence of other organic molecules, including biosurfactants. We have investigated the influence of the anionic surfactant sodium dodecyl sulfate (SDS on the adsorption of the siderophores DFOB (cationic and DFOD (neutral and the ligand EDTA (anionic onto goethite (α-FeOOH at pH 6. We also studied the adsorption of the corresponding 1:1 Fe(III-ligand complexes, which are products of the dissolution process. Adsorption of the two free siderophores increased in a similar fashion with increasing SDS concentration, despite their difference in molecule charge. In contrast, SDS had little effect on the adsorption of EDTA. Adsorption of the Fe-DFOB and Fe-DFOD complexes also increased with increasing SDS concentrations, while adsorption of Fe-EDTA decreased. Our results suggest that hydrophobic interactions between adsorbed surfactants and siderophores are more important than electrostatic interactions. However, for strongly hydrophilic molecules, such as EDTA and its iron complex, the influence of SDS on their adsorption seems to depend on their tendency to form inner-sphere or outer-sphere surface complexes. Our results demonstrate that surfactants have a strong influence on the adsorption of siderophores to Fe oxides, which has important implications for siderophore-promoted dissolution of iron oxides and biological iron acquisition.

Flavonoid-surfactant interactions: A detailed physicochemical study

Science.gov (United States)

Singh, Onkar; Kaur, Rajwinder; Mahajan, Rakesh Kumar

2017-01-01

The aim of this article is to study the interactions between flavonoids and surfactants with attention of finding the probable location of flavonoids in micellar media that can be used for controlling their antioxidant behavior. In present study, the micellar and interfacial behavior of twin tailed anionic surfactants viz. sodium bis(2-ethylhexyl)sulfosuccinate (AOT) and sodium bis(2-ethylhexyl)phosphate (NaDEHP) in the presence of two flavonoids, namely quercetin (QUE) and kaempferol (KFL) have been studied by surface tension measurements. UV-visible, fluorescence and differential pulse voltammetric (DPV) measurements have been employed to predict the probable location of flavonoids (QUE/KFL) within surfactant (AOT/NaDEHP) aggregates. Dynamic light scattering (DLS) measurements further confirmed the solubilization of QUE/KFL in AOT/NaDEHP aggregates deduced from increased hydrodynamic diameter (Dh) of aggregates in the presence of flavonoids. Both radical scavenging activity (RSA) and degradation rate constant (k) of flavonoids are found to be higher in NaDEHP micelles as compared to AOT micelles.

Effect of Surfactants on Plasmid DNA Stability and Release from ...

African Journals Online (AJOL)

Purpose: To evaluate the effect of surfactants on plasmid DNA during preparation and release from polylactic glycolide (PLGA) microspheres. Methods: Various surfactants, both ionic and non-ionic (Span, Tween, Triton X100, cetyltrimethylammonium bromide and sodium dodecyl sulphate), were added during the ...

Correlation and prediction of environmental properties of alcohol ethoxylate surfactants using the UNIFAC method

DEFF Research Database (Denmark)

Cheng, Hongyuan; Kontogeorgis, Georgios; Stenby, Erling Halfdan

2005-01-01

), the bioconcentration factor (BCF), and the toxicity. Kow values of alcohol ethoxylates are difficult to measure. Existing methods such as those in commercial software like ACD,ClogP and KowWin have not been applied to surfactants, and they fail for heavy alcohol ethoxylates (alkyl carbon numbers above 12). Thus...... and toxicity of alcohol ethoxylates are correlated with their Kow. The proposed approach can be extended to other families of nonionic surfactants....

Polyelectrolyte surfactant aggregates and their deposition on macroscopic surfaces

Energy Technology Data Exchange (ETDEWEB)

Voisin, David

2002-07-01

the CSC have been determined for mixtures of cationically modified guar gums (of varying charge density) with two anionic surfactants: sodium lauryl (or dodecyl) ether sulfate [SLES] and sodium dodecyl sulfate [SDS], for various concentrations of the polyelectrolyte and added sodium chloride, at room temperature. The addition of sodium chloride has only a minor net effect on the CFC, but increases the CSC significantly. The interactions between the cationic polyelectrolyte and the surfactant have been studied in the one-phase regions, i.e. below the CFC and above the CSC, using different techniques. Surface tension, electrophoresis, light scattering and viscosimetry have been employed. In the two-phase region, the sedimented floe phase has been analysed and the flocculation has been investigated. Rheology of the floe phase has been studied, after a mild compression by centrifugation. The initial rate of flocculation has been determined, using stop-flow equipment. The growth and the structure of the flocs have been investigated by light scattering. The open-network flocs of polyelectrolyte-surfactant particles grow to {approx}10's {mu}m in size, prior to their eventual settling out. Other colloidal particles can be trapped within these large flocs, and the flocs can be used to transport these particles to a macroscopic surface. The deposition and the removal of such composite flocs on glass surfaces, under flow, have been studied using a flow cell device coupled with an optical microscope. Scanning electron microscopy and atomic force microscopy have also been employed. (author)

Optimization of Surfactant Mixtures and Their Interfacial Behavior for Advanced Oil Recovery

Energy Technology Data Exchange (ETDEWEB)

Somasundaran, Prof. P.

2002-03-04

The objective of this project was to develop a knowledge base that is helpful for the design of improved processes for mobilizing and producing oil left untapped using conventional techniques. The main goal was to develop and evaluate mixtures of new or modified surfactants for improved oil recovery. In this regard, interfacial properties of novel biodegradable n-alkyl pyrrolidones and sugar-based surfactants have been studied systematically. Emphasis was on designing cost-effective processes compatible with existing conditions and operations in addition to ensuring minimal reagent loss.

Conductometric study of sodium dodecyl sulfate - nonionic surfactant (Triton X-100, Tween 20, Tween 60, Tween 80 or Tween 85 mixed micelles in aqueous solution

Directory of Open Access Journals (Sweden)

Ćirin Dejan M.

2012-01-01

Full Text Available The present study is concerned with the determination of the critical micelle concentration (cmc of mixed micelles of sodium dodecyl sulfate with one of five nonionic surfactants (Triton X-100, Tween 20, Tween 60, Tween 80 or Tween 85 from conductance measurements. Based on the calculated values of the β parameters we have noticed that SDS-nonionic surfactants mostly showed strong synergistic effect. It was found that nonionic surfactants with mainly longer and more hydrophobic tail show stronger interactions with hydrophobic part of SDS, thus expressing stronger synergism. In SDS-Tween 80 binary system the strongest synergistic effect was noticed. SDS-Tween 85 micellar system showed antagonistic effect, most probably because the presence of the double bond in its three hydrophobic tails (three C18 tails makes it sterically rigid.

Surfactant modified clays’ consistency limits and contact angles

Directory of Open Access Journals (Sweden)

S Akbulut

2012-07-01

Full Text Available This study was aimed at preparing a surfactant modified clay (SMC and researching the effect of surfactants on clays' contact angles and consistency limits; clay was thus modified by surfactants formodifying their engineering properties. Seven surfactants (trimethylglycine, hydroxyethylcellulose  octyl phenol ethoxylate, linear alkylbenzene sulfonic acid, sodium lauryl ether sulfate, cetyl trimethylammonium chloride and quaternised ethoxylated fatty amine were used as surfactants in this study. The experimental results indicated that SMC consistency limits (liquid and plastic limits changedsignificantly compared to those of natural clay. Plasticity index and liquid limit (PI-LL values representing soil class approached the A-line when zwitterion, nonionic, and anionic surfactant percentageincreased. However, cationic SMC became transformed from CH (high plasticity clay to MH (high plasticity silt class soils, according to the unified soil classification system (USCS. Clay modifiedwith cationic and anionic surfactants gave higher and lower contact angles than natural clay, respectively.

21 CFR 172.822 - Sodium lauryl sulfate.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium lauryl sulfate. 172.822 Section 172.822 Food... Multipurpose Additives § 172.822 Sodium lauryl sulfate. The food additive sodium lauryl sulfate may be safely... specifications: (1) It is a mixture of sodium alkyl sulfates consisting chiefly of sodium lauryl sulfate [CH2(CH2...

Preparation of the cactus-like porous manganese oxide assisted with surfactant sodium dodecyl sulfate for supercapacitors

Energy Technology Data Exchange (ETDEWEB)

Dai, Yu [State Key Laboratory of Advanced Metallurgy, University of Science and Technology Beijing, No. 30 College Road, Beijing 100083 (China); Li, Jianling, E-mail: lijianling@ustb.edu.cn [State Key Laboratory of Advanced Metallurgy, University of Science and Technology Beijing, No. 30 College Road, Beijing 100083 (China); Yan, Gang; Xu, Guofeng; Xue, Qingrui [State Key Laboratory of Advanced Metallurgy, University of Science and Technology Beijing, No. 30 College Road, Beijing 100083 (China); Kang, Feiyu [Lab of Advanced Materials, Department of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China)

2015-02-05

Highlights: • The cactus-like porous MnO{sub 2} was synthesized by hydrothermal method assisted with SDS. • The MnO{sub 2} exhibits a max specific capacitance of 187.8 F g{sup −1} (0.2 A g{sup −1}, 1 M Na{sub 2}SO{sub 4}). • Excellent cycling stability: 92.9% capacitance retention after 1000 cycles. - Abstract: The cactus-like porous manganese dioxide (MnO{sub 2}) was synthesized by a simple hydrothermal method assisted with the surfactant sodium dodecyl sulfate (SDS). The morphology, composition, property of the prepared materials were characterized by X-ray diffraction (XRD), Raman spectroscopy, Brunauer–Emmett–Teller (BET), Field Emission Scanning Electron Microscopy (FE-SEM) and Transmission Electron Microscopy (TEM) measurements. It was found that the sample without surfactant was composed of nanoflakes which piling up together, whereas in the presence of the surfactant, the MnO{sub 2} samples with the max specific surface of 321.9 m{sup 2} g{sup −1} showed a porous cactus-like microstructure, consisted of uniform nanowires and porous nanoflakes. The electrochemical performances of the MnO{sub 2} with and without surfactant were analyzed using Cyclic Voltammetry (CV), Electrochemical Impedance Spectrometry (EIS) and Galvanostatic Charge–Discharge (GCD) tests. The results showed that the MnO{sub 2} assisted with 1 wt.% SDS displayed a higher specific capacitance of 187.8 F g{sup −1} at the current density of 0.2 A g{sup −1} compared with the MnO{sub 2} without surfactant (134.8 F g{sup −1}). And such MnO{sub 2} samples with higher specific capacitance also afford an excellent cyclic stability with the capacity retention of approximately 92.9% after 1000 cycles in 1 M Na{sub 2}SO{sub 4} solution at a current density of 1 A g{sup −1}. The superior capacitive performance of the as-prepared materials could be attributed to its unique cactus-like porous structure, which provided good electronic conductivity, large specific surface area as

Influence of metacide - surfactant complexes on agricultural crops

Directory of Open Access Journals (Sweden)

Orynkul Esimova

2014-12-01

Full Text Available The complexes based on surfactants and polyhexamethyleneguanidine hydrochloride (metacide are important for agriculture. This paper considers compositions of known bactericidal metacide with different surfactants: anionic surfactant sodium dodecylsulphate (DDSNa and nonionic surfactant Tween 80 (monooleate of oxyethylenated anhydrosorbitols. The effect of individual components and associates of metacide and surfactants on productivity and infection of cereals was studied. According to the study, the highest productivity and infection rate were shown by the associate of metacide and Tween-80. At concentration of Tween-80 in aqueous solution equal to 0.001% in combination with metacide, efficiency was 98% at 0% infection. The surface tension and the wetting of metacide, DDSNa, Tween-80, and associates of metacide with surfactants were studied. In comparison with individual components, metacide-DDSNa and metacide-Tween-80 associates have higher surface activity.

Surfactant-nanotube interactions in water and nanotube separation by diameter: atomistic simulations

Science.gov (United States)

Carvalho, E. J. F.; Dos Santos, M. C.

2010-05-01

A non-destructive sorting method to separate single-walled carbon nanotubes (SWNTs) by diameter was recently proposed. By this method, SWNTs are suspended in water by surfactant encapsulation and the separation is carried out by ultracentrifugation in a density gradient. SWNTs of different diameters are distributed according to their densities along the centrifuge tube. A mixture of two anionic surfactants, namely sodium dodecylsulfate (SDS) and sodium cholate (SC), presented the best performance in discriminating nanotubes by diameter. Unexpectedly, small diameter nanotubes are found at the low density part of the centrifuge tube. We present molecular dynamics studies of the water-surfactant-SWNT system to investigate the role of surfactants in the sorting process. We found that surfactants can actually be attracted towards the interior of the nanotube cage, depending on the relationship between the surfactant radius of gyration and the nanotube diameter. The dynamics at room temperature showed that, as the amphiphile moves to the hollow cage, water molecules are dragged together, thereby promoting the nanotube filling. The resulting densities of filled SWNT are in agreement with measured densities.

Interactions of structurally modified surfactants with reservoir minerals: Calorimetric, spectroscopic and electrokinetic study

Energy Technology Data Exchange (ETDEWEB)

Somasundaran, P.; Sivakumar, A.; Xu, Q.

1991-03-01

The objective of this project is to elucidate mechanisms of adsorption of structurally modified surfactants on reservoir minerals and to develop a full understanding of the effect of the surfactant structure on the nature of the adsorbed layers at the molecular level. An additional aim is to study the adsorption of surfactant mixtures on simple well-characterized minerals and on complex minerals representing real conditions. The practical goal of these studies is the identification of the optimum surfactant structures and their combinations for micellar flooding. In this work, the experiments on adsorption were focussed on the position of sulfonate and methyl groups on the aromatic ring of alkyl xylene sulfonates. A multi-pronged approach consisting of calorimetry, electrokinetics, wettability and spectroscopy is planned to elucidate the adsorption mechanism of surfactants and their mixtures on minerals such as alumina and kaolinite. 32 refs., 15 figs., 7 tabs.

Effect of Gemini-type surfactant on methane hydrate formation

Energy Technology Data Exchange (ETDEWEB)

Jeong, K.E.; Park, J.M.; Kim, C.U.; Chae, H.J.; Jeong, S.Y. [Korea Research Inst. of Chemical Technology, Jang-Dong, Yuseong-Gu, Daejeon (Korea, Republic of)

2008-07-01

Natural gas hydrates are formed from water and natural gas molecules at particular temperatures and pressures that become ice-like inclusion compounds. Gas hydrates offer several benefits such as energy resource potential and high storage capacity of natural gas in the form of hydrates. However, the application of natural gas hydrates has been deterred by its low formation rate and low conversion ratio of water into hydrate resulting in low actual storage capacity. This paper presented an experimental study to determine the effect of adding a novel Gemini-type surfactant on methane hydrate formation. The experimental study was described with reference to the properties of prepared diols and properties of prepared disulfonates. Gemini surfactant is the family of surfactant molecules possessing more than one hydrophobic tail and hydrophilic head group. They generally have better surface-active properties than conventional surfactants of equal chain length. The paper presented the results of the study in terms of the reactions of diols with propane sultone; storage capacity of hydrate formed with and without surfactant; and methane hydrate formation with and without disulfonate. It was concluded that the methane hydrate formation was accelerated by the addition of novel anionic Gemini-type surfactants and that hydrate formation was influenced by the surfactant concentration and alkyl chain length. For a given concentration, the surfactant with the highest chain length demonstrated the highest formation rate and storage capacity. 5 refs., 3 tabs., 4 figs.

Determination of trace quaternary ammonium surfactants in water by combining solid-phase extraction with surface-assisted laser desorption/ionization mass spectrometry.

Science.gov (United States)

Chen, Y C; Sun, M C

2001-01-01

This study demonstrates the feasibility of combining solid-phase extraction (SPE) with surface-assisted laser desorption/ionization (SALDI) mass spectrometry to determine trace quaternary ammonium surfactants in water. The trace surfactants in water were directly concentrated on the surface of activated carbon sorbent in SPE. The activated carbon sorbent was then mixed with the SALDI liquid for SALDI analysis. No SPE elution procedure was necessary. Experimental results indicate that the surfactants with longer chain alkyl groups exhibit higher sensitivities than those with shorter chain alkyl groups in SPE-SALDI analysis. The detection limit for hexadecyltrimethylammonium bromide is around 10 ppt in SPE-SALDI analysis by sampling 100 mL of aqueous solution, while that of tetradecyltrimethylammonium bromide is about 100 ppt. The detection limit for decyltrimethylammonium bromide and dodecyltrimethylammonium bromide is in the low-ppb range. Copyright 2001 John Wiley & Sons, Ltd.

Remediation of Nitrobenzene Contaminated Soil by Combining Surfactant Enhanced Soil Washing and Effluent Oxidation with Persulfate

Science.gov (United States)

Yan, Jingchun; Gao, Weiguo; Qian, Linbo; Han, Lu; Chen, Yun; Chen, Mengfang

2015-01-01

The combination of surfactant enhanced soil washing and degradation of nitrobenzene (NB) in effluent with persulfate was investigated to remediate NB contaminated soil. Aqueous solution of sodium dodecylbenzenesulfonate (SDBS, 24.0 mmol L-1) was used at a given mass ratio of solution to soil (20:1) to extract NB contaminated soil (47.3 mg kg-1), resulting in NB desorption removal efficient of 76.8%. The washing effluent was treated in Fe2+/persulfate and Fe2+/H2O2 systems successively. The degradation removal of NB was 97.9%, being much higher than that of SDBS (51.6%) with addition of 40.0 mmol L-1 Fe2+ and 40.0 mmol L-1 persulfate after 15 min reaction. The preferential degradation was related to the lone pair electron of generated SO4•−, which preferably removes electrons from aromatic parts of NB over long alkyl chains of SDBS through hydrogen abstraction reactions. No preferential degradation was observed in •OH based oxidation because of its hydrogen abstraction or addition mechanism. The sustained SDBS could be reused for washing the contaminated soil. The combination of the effective surfactant-enhanced washing and the preferential degradation of NB with Fe2+/persulfate provide a useful option to remediate NB contaminated soil. PMID:26266532

Application of positron annihilation techniques to the study of micels and microemulsions

International Nuclear Information System (INIS)

Olea C, O.

1981-01-01

The molecular auto-association mechanisms in sodium-oleate-alcohol-alkane-water systems were studied, applying positron and positronium annihilation techniques. The effects of the different component structures of these systems and of their concentrations on the swelled micel formation process which eventually produce microemulsions, were also investigated. The influences studied were: a) co-surfactant (alcohol) hydrocarbon chain lengths, b) alkane (oil) hydrocarbon chain lengths, c) surfactant concentrations, and d) surfactant double link alkylic chains. (author)

Kinetic study of the anaerobic biodegradation of alkyl polyglucosides and the influence of their structural parameters.

Science.gov (United States)

Ríos, Francisco; Fernández-Arteaga, Alejandro; Lechuga, Manuela; Jurado, Encarnación; Fernández-Serrano, Mercedes

2016-05-01

This paper reports a study of the anaerobic biodegradation of non-ionic surfactants alkyl polyglucosides applying the method by measurement of the biogas production in digested sludge. Three alkyl polyglucosides with different length alkyl chain and degree of polymerization of the glucose units were tested. The influence of their structural parameters was evaluated, and the characteristics parameters of the anaerobic biodegradation were determined. Results show that alkyl polyglucosides, at the standard initial concentration of 100 mgC L(-1), are not completely biodegradable in anaerobic conditions because they inhibit the biogas production. The alkyl polyglucoside having the shortest alkyl chain showed the fastest biodegradability and reached the higher percentage of final mineralization. The anaerobic process was well adjusted to a pseudo first-order equation using the carbon produced as gas during the test; also, kinetics parameters and a global rate constant for all the involved metabolic process were determined. This modeling is helpful to evaluate the biodegradation or the persistence of alkyl polyglucosides under anaerobic conditions in the environment and in the wastewater treatment.

Effect of Dialkyl Ammonium Cationic Surfactants on the Microfluidity of Membranes Containing Raft Domains.

Science.gov (United States)

Uyama, Makoto; Inoue, Kaori; Kinoshita, Koichi; Miyahara, Reiji; Yokoyama, Hirokazu; Nakano, Minoru

2018-01-01

It has been reported that a lot of receptors localize in lipid raft domains and that the microfluidity of these domains regulates the activation of these receptors. In this study, we focused on the lipid raft and in order to evaluate the physicochemical effects of surfactants on microfluidity of lipid membranes, we used liposomes comprising of egg-yolk L-α-phosphatidylcholine, egg-yolk sphingomyelin, and cholesterol as a model of cell membranes containing raft domains. The microfluidity of the domains was characterized by fluorescence spectrometry using 1,6-diphenyl-1,3,5-hexatriene and 2-dimethylamino-6-lauroylnaphthalene. Among several surfactants, dialkylammonium-type cationic surfactants most efficiently increased the microfluidity. It is therefore concluded that (1) the electrostatic interaction between the cationic surfactant and eggPC/eggSM/cholesterol liposome could be important, (2) surfactants with alkyl chains more effectively inserted into membranes than those with acyl chains, and (3) cationic surfactants with lower T m values have a greater ability to increase the fluidity.

Surfactant loss control in chemical flooding spectroscopic and calorimetric study of adsorption and precipitation on reservoir minerals. Annual report, September 30, 1992--September 30 1995

Energy Technology Data Exchange (ETDEWEB)

Casteel, J. [Bartlesville Project Office, OK (United States)

1996-07-01

The aim of this research project was to investigate mechanisms governing adsorption and surface precipitation of flooding surfactants on reservoir minerals. Effects of surfactant structure, surfactant combinations, various inorganic and polymeric species, and solids mineralogy have been determined. A multi-pronged approach consisting of micro & nano spectroscopy, electrokinetics, surface tension and wettability is used in this study. The results obtained should help in controlling surfactant loss in chemical flooding and in developing optimum structures and conditions for efficient chemical flooding processes. During the three years contract period, adsorption of single surfactants and select surfactant mixtures was studied at the solid-liquid and gas-liquid interfaces. Alkyl xylene sulfonates, polyethoxylated alkyl phenols, octaethylene glycol mono n-decyl ether, and tetradecyl trimethyl ammonium chloride were the surfactants studied. Adsorption of surfactant mixtures of varying composition was also investigated. The microstructure of the adsorbed layer was characterized using fluorescence spectroscopy. Changes in interfacial properties such as wettability, electrokinetics and stability of reservoir minerals were correlated with the amounts of reagent adsorbed. Strong effects of the structure of the surfactant and position of functional groups were revealed. Changes of microstructure upon dilution (desorption) were also studied. Presence of the nonionic surfactants in mixed aggregate leads to shielding of the charge of ionic surfactants which in turn promotes aggregation but reduced electrostatic attraction between the charged surfactant and the mineral surface. Strong consequences of surfactant interactions in solution on adsorption as well as correlations between monomer concentration in mixtures and adsorption were revealed.

EVALUATION OF STABILITY OF EMULSION OIL / WATER FRONT OF THE USE OF DIFFERENT SURFACTANTS

Directory of Open Access Journals (Sweden)

Fernanda Cristina Wiedusch Sindelar

2013-05-01

Full Text Available The reuse of waste generated by various industrial sectors is a practice that has been increasingly used due to impairment of industries with their social responsibility (environmental protection or the requirements of the protection of the environment, since many residues do not have proper disposal. In the processing industry in the reuse of stones is no different. This study aims to evaluate the reuse of the oil used as a lubricant in the stone processing industry, along with water, surfactants and corrosion. To prepare the emulsions samples were used of diesel oil as a lubricant used in the cutting industry this type of industry, plus the following surfactants: Tween 20, Tween 80, sodium lauryl ether sulphate and Cetiol HE. After completing the pH, viscosity, density and phase separation in these emulsions, the conclusion was reached that the surfactant Sodium Lauryl Ether Sulfate provided the best formulation. Using this result, new emulsions prepared with the surfactant Sodium Lauryl Ether Sulfate and an anticorrosive, in this case, sodium molybdate. In such solutions containing sodium molybdate were analyzed power anticorrosive this substance, using the SAE 1020 steel plates. After these analyzes, it was found that the addition of an anticorrosive may reduce or inhibit oxidation, but in other cases, as in this study, can promote oxidation even greater.

Effect of presence of benzene ring in surfactant hydrophobic chain on the transformation towards one dimensional aggregate

Directory of Open Access Journals (Sweden)

Rabah A. Khalil

2015-07-01

Full Text Available The formation of wormlike micelle and the following significant changes in rheological properties suffer misunderstanding from both theoretical and fundamental aspects. Recently, we have introduced a theory for interpreting such important phenomenon which is referred to as critical intermolecular forces (CIF. The theory has stated that the hydrophobic effect is the main factor for the formation of worm-like aggregates. Therefore, it seems interesting to check out the validity of this new physical insight through investigating the presence of benzene ring as less hydrophobic group in contrast to that of alkyl in surfactant tail. The mixture of anionic sodium dodecylbenzenesulphonate (SDBS and cationic cetyltrimethylammonium bromide (CTAB shows a high dynamic viscosity peak at the ratio of 80/20 of 3 wt.% CTAB/SDBS indicating the formation of wormlike micelles. The thermodynamic properties have been evaluated for this mixture exhibiting good agreement with the rheological changes. Interestingly, the results show the presence of benzene ring (in SDBS causing a negative effect towards the formation of one dimensional aggregate in contrast to previous results which support the proposed CIF theory. The presence of nonionic surfactant TritonX-100 in binary and ternary systems of SDBS and CTAB prohibits the formation of wormlike micelles.

Dynamics of Surfactant Clustering at Interfaces and Its Influence on the Interfacial Tension: Atomistic Simulation of a Sodium Hexadecane-Benzene Sulfonate-Tetradecane-Water System.

Science.gov (United States)

Paredes, Ricardo; Fariñas-Sánchez, Ana Isabel; Medina-Rodrı Guez, Bryan; Samaniego, Samantha; Aray, Yosslen; Álvarez, Luis Javier

2018-03-06

The process of equilibration of the tetradecane-water interface in the presence of sodium hexadecane-benzene sulfonate is studied using intensive atomistic molecular dynamics simulations. Starting as an initial point with all of the surfactants at the interface, it is obtained that the equilibration time of the interface (several microseconds) is orders of magnitude higher than previously reported simulated times. There is strong evidence that this slow equilibration process is due to the aggregation of surfactants molecules on the interface. To determine this fact, temporal evolution of interfacial tension and interfacial formation energy are studied and their temporal variations are correlated with cluster formation. To study cluster evolution, the mean cluster size and the probability that a molecule of surfactant chosen at random is free are obtained as a function of time. Cluster size distribution is estimated, and it is observed that some of the molecules remain free, whereas the rest agglomerate. Additionally, the temporal evolution of the interfacial thickness and the structure of the surfactant molecules on the interface are studied. It is observed how this structure depends on whether the molecules agglomerate or not.

Removal Efficiency of Linear Alkyl Benzene Sulfonate (LAS in Yazd Stabilization Pond

Directory of Open Access Journals (Sweden)

Asghar Ebrahimi

2011-01-01

Full Text Available Surfactants are organic chemicals with wide applications as detergents. Linear alkyl benzene sulfonate (LAS is an anionic surfactant most commonly used. Discharge of raw or treated wastewater containing this chemical into the environment causes major public health problems. In this study, 64 samples were taken from the effluent of Yazd Wastewater  Treatment Plant over a period of one year. The samples were analyzed according to standard methods. The results obtained from the samples taken in different seasons showed that the highest efficiency of anionic surfactant removal was achieved in the summer in the secondary facultative stabilization pond. The least efficiency was observed in the autumn in samples from the anaerobic stabilization pond. It was also found that treated wastewater discharged into surface waters, reused for agricultural irrigation, or discharged into absorbent wells had significant differences with Pvalue

Switching wormlike micelles of selenium-containing surfactant using redox reaction.

Science.gov (United States)

Zhang, Yongmin; Kong, Weiwei; Wang, Cheng; An, Pengyun; Fang, Yun; Feng, Yujun; Qin, Zhirong; Liu, Xuefeng

2015-10-14

A novel redox-switchable wormlike micellar system was developed based on a mixture of selenium-containing zwitterionic surfactant and commercially available anionic surfactant sodium dodecyl sulfate, which reversibly and quickly responds to H2O2 and vitamin C, and shows circulatory gel/sol transition, reflecting changes in aggregate morphology from entangled worms to vesicles.

Synergism and Physicochemical Properties of Anionic/Amphoteric Surfactant Mixtures with Nonionic Surfactant of Amine Oxide Type

Science.gov (United States)

Blagojević, S. M.; Pejić, N. D.; Blagojević, S. N.

2017-12-01

The physicochemical properties of initial formulation, that is anionic/amphoteric surfactants mixture SLES/AOS/CAB (sodium lauryl ether sulfate (SLES), α-olefin sulfonates (AOS) and cocamidopropyl betaine (CAB) at ratio 80 : 15 : 5) with nonionic surfactant of amine oxide type (lauramine oxide (AO)) in various concentration (1-5%) were studied. To characterize the surfactants mixture, the critical micelle concentration (CMC), surface tension (γ), foam volume, biodegradability and irritability were determined. This study showed that adding of AO in those mixtures lowered both γ and CMC as well as enhanced SLES/AOS/CAB foaming properties, but did not significantly affect biodegradability and irritability of initial formulation. Moreover, an increase in AO concentration has a meaningful synergistic effect on the initial formulation properties. All those results indicates that a nonionic surfactant of amine oxide type significantly improves the performance of anionic/amphoteric mixed micelle systems, and because of that anionic/amphoteric/nonionic mixture can be used in considerably lower concentrations as a cleaning formulation.

Analysis of polyethoxylated surfactants in microemulsion-oil-water systems III. Fractionation and partitioning of polyethoxylated alcohol surfactants

International Nuclear Information System (INIS)

Marquez, N.; Bravo, B.; Ysambertt, F.; Chavez, G.; Subero, N.; Salager, J.L.

2002-01-01

Oligomer distribution of polyethoxylated alcohol and polyethoxylated nonylphenol surfactants is studied by normal and reverse-phase high performance liquid chromatography (HPLC). A RP8 column is able to efficiently separate these surfactants according to their alkyl chain (lipophilic) group, while silica and amino columns separate them according to their polyether chain length (hydrophilic group). Polyethoxylated alcohol and polyethoxylated nonylphenol oligomers selectively partition between the microemulsion-oil-water phases of a Winsor III system. Partitioning of these oligomers was analyzed by HPLC with RI detection. The logarithm of the partition coefficient between the water and oil linearly increases with the number of ethylene oxide groups per molecule of oligomer. For a same ethoxylation degree, the partition coefficient of a polyethoxylated tridecanol is found to be higher than the one of the corresponding nonylphenol specie. On the other hand, a polyethoxylated nonylphenol exhibits a higher solubilization than the matching polyethoxylated alcohol

Photochemical key steps in the synthesis of surfactants from furfural-derived intermediates.

Science.gov (United States)

Gassama, Abdoulaye; Ernenwein, Cédric; Hoffmann, Norbert

2009-01-01

Furfural is oxidized to 2[5H]-furanone by using hydrogen peroxide or to 5-hydroxy-2[5H]-furanone by using photo-oxygenation. An amine function is introduced by photochemically induced radical addition of tertiairy amines, some of which carry an n-alkyl side chain as hydrophobic moiety. These amines are produced from fatty aldehydes and cyclic secondary amines. The resulting adducts are transformed into amphoteric surfactants possessing an ammonium and a carboxylate function. Amphoteric (pK(N) and isoelectric point) and surfactant properties such as the critical micelle concentration and the adsorption efficiency are determined.

Surfactant-induced mobilisation of trace metals from estuarine sediment: Implications for contaminant bioaccessibility and remediation

Energy Technology Data Exchange (ETDEWEB)

Singh, Anu [School of Earth, Ocean and Environmental Sciences, University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom); Turner, Andrew [School of Earth, Ocean and Environmental Sciences, University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom)], E-mail: aturner@plymouth.ac.uk

2009-02-15

The mobilisation of metals (Al, Fe, Cd, Cu, Mn, Ni, Pb, Sn, Zn) from contaminated estuarine sediment has been examined using commercially available surfactants. Metal release by the anionic surfactant, sodium dodecyl sulphate (SDS), increased with increasing amphiphile concentration up to and above its critical micelle concentration (CMC). Metal mobilisation by the bile acid salt, sodium taurocholate, and the nonionic surfactant, Triton X-100, however, did not vary with amphiphile concentration. SDS was the most efficient surfactant in mobilising metals from the sample, and Cd, Cu and Ni were released to the greatest extents (12-18% of total metal at [SDS] > CMC). Metal mobilisation appeared to proceed via complexation with anionic amphiphiles and denudation of hydrophobic host phases. Surfactants may play an important role in the solubilisation of metals in the digestive environment of deposit-feeding animals and, potentially, in the remediation of metal-contaminated soil and sediment. - Significant quantities of metals are mobilised from estuarine sediment by commercially available surfactants.

Chemistry of the pyrazolidines. 26. Alkylation of 4-benzyliden-1-phenyl-3,5-dioxopyrazolidines

International Nuclear Information System (INIS)

Moldarev, B.L.; Aronzon, M.E.; Adanin, V.M.; Zyakun, A.M.

1986-01-01

The reaction of 4-benzyliden-1-phenyl-3,5-dioxopyrazolidines with alkyl halides in the presence of sodium alkoxide gave 1-phenyl-2-alkyl-4-benzyliden- and 1-phenyl-2,4-dialkyl-4-(α-alkoxybenzyl)-3,4-dioxopyrazolines. The structures of these compounds were confirmed by UV, IR, and PMR spectroscopy, and by mass-spectrometry

Interactions between Surfactants in Solution and Electrospun Protein Fibers: Effects on Release Behavior and Fiber Properties

DEFF Research Database (Denmark)

Boutrup Stephansen, Karen; García-Díaz, María; Jessen, Flemming

2016-01-01

, and drug delivery. In the present study, we present a systematic investigation of how surfactants and proteins, as physiologically relevant components, interact with insulin-loaded fish sarcoplasmic protein (FSP) electrospun fibers (FSP-Ins fibers) in solution and thereby affect fiber properties...... such as accessible surface hydrophilicity, physical stability, and release characteristics of an encapsulated drug. Interactions between insulin-loaded protein fibers and five anionic surfactants (sodium taurocholate, sodium taurodeoxycholate, sodium glycocholate, sodium glycodeoxycholate, and sodium dodecyl sulfate......Intermolecular interaction phenomena occurring between endogenous compounds, such as proteins and bile salts, and electrospun compounds are so far unreported, despite the exposure of fibers to such biorelevant compounds when applied for biomedical purposes, e.g., tissue engineering, wound healing...

Polyelectrolyte-surfactant complexes formed by poly[3,5-bis(trimethylammoniummethyl)4-hydroxystyrene iodide]-block-poly(ethylene oxide) and sodium dodecyl sulfate in aqueous solutions

Czech Academy of Sciences Publication Activity Database

Štěpánek, M.; Matějíček, P.; Procházka, K.; Filippov, Sergey K.; Angelov, Borislav; Šlouf, Miroslav; Mountrichas, G.; Pispas, S.

2011-01-01

Roč. 27, č. 9 (2011), s. 5275-5281 ISSN 0743-7463 R&D Projects: GA MŠk ME09059; GA ČR GCP205/11/J043; GA ČR GAP208/10/0353 Institutional research plan: CEZ:AV0Z40500505 Keywords : polyelectrolyte-surfactant complexes * sodium dodecyl sulfate * small-angle X-ray scattering Subject RIV: CD - Macromolecular Chemistry Impact factor: 4.186, year: 2011

Effects of Surfactant on Geotechnical Characteristics of Silty Soil

International Nuclear Information System (INIS)

Rahman, Z.A.; Sahibin, A.R.; Lihan, T.; Idris, W.M.R.; Sakina, M.

2013-01-01

Surfactants are often used as a cleaning agent for restoration of oil-contaminated soil. However the effect of surfactant on the geotechnical properties of soil is not clearly understood. In this study, the effects of surfactant on silty soil were investigated for consistency index, compaction, permeability and shear strength. Sodium dodecyl sulfate (SDS) was used in this study to prepare the surfactant-treated soil. Our results showed that the soil with added surfactant exhibited a decrease in liquid and plastic limit values. Maximum dry densities increased and optimum moisture contents decreased as contents of added surfactant were increased. The presence of surfactant assists the soil to achieve maximum density at lower water content. The addition of surfactant decreased the permeability of soil from 6.29 x 10 -4 to 1.15 x 10 -4 ms -1 . The shear strength of soil with added surfactant was examined using the undrained unconsolidated triaxial tests. The results showed that the undrained shear strength, Cu was significantly affected, decreased from 319 kPa to 50 kPa for soil with 20 % of added surfactant. The results of this study showed that the presence of surfactant in soil can modify the mechanical behaviour of the soil. (author)

A kinetic study of 1,3-dipolar cycloadditions in micellar media

NARCIS (Netherlands)

Rispens, T; Engberts, JBFN

2003-01-01

The kinetics of the 1,3-dipolar cycloadditions (DC) of benzonitrile oxide with a series of N-substituted maleimides in micellar media have been investigated. Surfactants studied include anionic sodium dodecyl sulfate, cationic cetyltrimethylammonium bromide, and a series of nonionic alkyl

Nanoparticle decoration with surfactants: Molecular interactions, assembly, and applications

Science.gov (United States)

Heinz, Hendrik; Pramanik, Chandrani; Heinz, Ozge; Ding, Yifu; Mishra, Ratan K.; Marchon, Delphine; Flatt, Robert J.; Estrela-Lopis, Irina; Llop, Jordi; Moya, Sergio; Ziolo, Ronald F.

2017-02-01

Nanostructures of diverse chemical nature are used as biomarkers, therapeutics, catalysts, and structural reinforcements. The decoration with surfactants has a long history and is essential to introduce specific functions. The definition of surfactants in this review is very broad, following its lexical meaning ;surface active agents;, and therefore includes traditional alkyl modifiers, biological ligands, polymers, and other surface active molecules. The review systematically covers covalent and non-covalent interactions of such surfactants with various types of nanomaterials, including metals, oxides, layered materials, and polymers as well as their applications. The major themes are (i) molecular recognition and noncovalent assembly mechanisms of surfactants on the nanoparticle and nanocrystal surfaces, (ii) covalent grafting techniques and multi-step surface modification, (iii) dispersion properties and surface reactions, (iv) the use of surfactants to influence crystal growth, as well as (v) the incorporation of biorecognition and other material-targeting functionality. For the diverse materials classes, similarities and differences in surfactant assembly, function, as well as materials performance in specific applications are described in a comparative way. Major factors that lead to differentiation are the surface energy, surface chemistry and pH sensitivity, as well as the degree of surface regularity and defects in the nanoparticle cores and in the surfactant shell. The review covers a broad range of surface modifications and applications in biological recognition and therapeutics, sensors, nanomaterials for catalysis, energy conversion and storage, the dispersion properties of nanoparticles in structural composites and cement, as well as purification systems and classical detergents. Design principles for surfactants to optimize the performance of specific nanostructures are discussed. The review concludes with challenges and opportunities.

Ecotoxicological assessment of the pharmaceutical fluoxetine hydrochloride and the surfactant dodecyl sodium sulfate after their submission to ionizing radiation treatment

International Nuclear Information System (INIS)

Santos, Dymes Rafael Alves dos

2011-01-01

The use of pharmaceuticals and personal care products and the consequent and continuous input of this substances in the environment generates an increasing need to investigate the presence, behavior and the effects on aquatic biota, as well as new ways to treat effluents containing such substances. Fluoxetine hydrochloride is an active ingredient used in the treatment of depressive disorders and anxiety. As the surfactant sodium dodecyl sulfate is present in many cleaning and personal care products. The present study aimed on assessing the acute toxicity of fluoxetine hydrochloride, sodium dodecyl sulfate and the mixture of both to the aquatic organisms Hyalella azteca, Daphnia similis and Vibrio ficheri. Reducing the toxicity of fluoxetine and the mixture after treatment with ionizing radiation from industrial electron beam accelerator has also been the focus of this study. For Daphnia similis the average values of CE50-4 8h found for the non-irradiated drug, surfactant and mixture were 14.4 %, 9.62 % and 13.8 %, respectively. After irradiation of the substances, the dose 5 kGy proved itself to be the most effective dose for the treatment of the drug and the mixture as it was obtained the mean values for CE50 48h 84.60 % and > 90 %, respectively. For Hyalella azteca the acute toxicity tests were performed for water column with duration of 96 hours, the mean values for CE50 96h found for the drug, the surfactant and the mixture non-irradiated were 5.63 %, 19.29 %, 6.27 %, respectively. For the drug fluoxetine and the mixture irradiated with 5 kGy, it was obtained 69.57 % and 77.7 %, respectively. For Vibrio ficheri the acute toxicity tests for the untreated drug and the drug irradiated with 5 kGy it was obtained CE50 15min of 6.9 % and 32.88 % respectively. These results presented a reduction of the acute toxicity of the test-substances after irradiation. (author)

Permaflood, formation in situ of surfactants

Energy Technology Data Exchange (ETDEWEB)

Kapo, G

1972-01-01

The present paper described a new process to produce surfactants in situ in which advantage is taken of the chemical reaction of oxidation in the liquid phase. This process consists of injecting a front of oxidizing agents and reaction compounds, in order to avoid the precipitation of the reaction products and to avoid the interaction between the surfactants produced and the calcium and magnesium in the connate water. Many different types of oxidizing agents as sodium dichromate, hydrogen peroxide, potassium permanganate, sodium hypochlorite, etc., are used. Also, there is considered the use of catalyzers with these oxidizing agents and the variation of the pH of the oxidizing front (permanaganate was the first oxidant used to check the technical and economic possibilities of this process in the laboratory). The process is called Permaflood, so named because potassium permanganate was the first oxidant used to check the technical and economic possibilities of this process in the laboratory.

Effects of alkyl polyglycoside (APG) on Bombyx mori silk degumming and the mechanical properties of silk fibroin fibre

Energy Technology Data Exchange (ETDEWEB)

Wang, Fei; Zhang, Yu-Qing, E-mail: sericult@suda.edu.cn

2017-05-01

Alkyl polyglycoside (APG), a nonionic surfactant, is often considered to be a green surfactant and is synthesized using glucose and long chain fatty alcohols. It is used as a degumming agent of Bombyx mori silk fibre in this study for the first time. We studied APG systematically in comparison to the traditional degumming methods, such as aqueous solutions of sodium carbonate (Na{sub 2}CO{sub 3}) and neutral soap (NS). After repeatedly boiling silk fibres in an aqueous solution of 0.25% APG three times for 30 min and using a bath ratio of 1:90–120 (g/mL), sericin was completely removed from the fibre. SDS-PAGE showed that the degumming in APG did not induce an evident breakage of the silk fibroin peptide chains, including the light chain and P25 protein. The tensile properties, thermal analysis, and scanning electron microscopic (SEM) observation of the degummed fibroin fibre all show that APG is a degumming agent similar to NS and far superior to Na{sub 2}CO{sub 3}. These results indicate that APG is an environment-friendly silk degumming/refining agent in the silk textile industry and in the manufacture of silk floss quilts. - Graphical abstract: APG has potential uses as a green degumming/refining reagent for silkworm cocoons or silk fibres in the silk industry and for sericulture production. Display Omitted.

Status of surfactants as penetration enhancers in transdermal drug delivery

Directory of Open Access Journals (Sweden)

Iti Som

2012-01-01

Full Text Available Surfactants are found in many existing therapeutic, cosmetic, and agro-chemical preparations. In recent years, surfactants have been employed to enhance the permeation rates of several drugs via transdermal route. The application of transdermal route to a wider range of drugs is limited due to significant barrier to penetration across the skin which is associated with the outermost stratum corneum layer. Surfactants have effects on the permeability characteristics of several biological membranes including skin. They have the potential to solubilize lipids within the stratum corneum. The penetration of the surfactant molecule into the lipid lamellae of the stratum corneum is strongly dependent on the partitioning behavior and solubility of surfactant. Surfactants ranging from hydrophobic agents such as oleic acid to hydrophilic sodium lauryl sulfate have been tested as permeation enhancer to improve drug delivery. This article reviews the status of surfactants as permeation enhancer in transdermal drug delivery of various drugs.

Antimicrobial Activity of Single-Walled Carbon Nanotubes Suspended in Different Surfactants

Directory of Open Access Journals (Sweden)

Lifeng Dong

2012-01-01

Full Text Available We investigated the antibacterial activity of single-walled carbon nanotubes (SWCNTs dispersed in surfactant solutions of sodium cholate, sodium dodecylbenzene sulfonate, and sodium dodecyl sulfate. Among the three surfactants, sodium cholate demonstrated the weakest antibacterial activity against Salmonella enterica, Escherichia coli, and Enterococcus faecium and thereby was used to disperse bundled SWCNTs in order to study nanotube antibiotic activity. SWCNTs exhibited antibacterial characteristics for both S. enterica and E. coli. With the increase of nanotube concentrations from 0.3 mg/mL to 1.5 mg/mL, the growth curves had plateaus at lower absorbance values whereas the absorbance value was not obviously affected by the incubation ranging from 5 min to 2 h. Our findings indicate that carbon nanotubes could become an effective alternative to antibiotics in dealing with drug-resistant and multidrug-resistant bacterial strains because of the physical mode of bactericidal action that SWCNTs display.

Studying the silver nanoparticles influence on thermodynamic behavior and antimicrobial activities of novel amide Gemini cationic surfactants.

Science.gov (United States)

Shaban, Samy M; Abd-Elaal, Ali A

2017-07-01

Three novels amide Gemini cationic surfactants with various alkyl chains and their silver nanohybrid with silver nanoparticles were synthesized and a confirmation study for surfactant and their nanoparticles formation has been established using IR, 1 HNMR, TEM and UV-Vis spectroscopy. The surface-active properties of these surfactants and their nanoform were investigated through surface tension and electrical conductivity measurements and a comparative study has been established. The thermodynamic parameters of micellization and adsorption were assessed at temperatures range from 25 to 65°C. The effect of silver particles on the surface behavior of the synthesized surfactant has been discussed. The aggregation behavior of silver nanoparticles with these synthesized Gemini surfactants in water were investigated using dynamic light scattering and transmission electron microscopy. Furthermore, the antimicrobial activities of these synthesized amide Gemini surfactants and their nanostructure with silver against both Gram positive and Gram negative bacteria were also investigated. Copyright © 2017 Elsevier B.V. All rights reserved.

The Effect Of Organic Surfactants On The Properties Of Common Hygroscopic Particles: Effective Densities, Reactivity And Water Evaporation Of Surfactant Coated Particles

Science.gov (United States)

Cuadrarodriguez, L.; Zelenyuk, A.; Imre, D.; Ellison, B.

2006-12-01

Measurements of atmospheric aerosol compositions routinely show that organic compounds account for a very large fraction of the particle mass. The organic compounds that make up this aerosol mass represent a wide range of molecules with a variety of properties. Many of the particles are composed of hygroscopic salts like sulfates, nitrates and sea-salt internally mixed with organics. While the properties of the hygroscopic salts are known, the effect of the organic compounds on the microphysical and chemical properties which include CCN activity is not clear. .One particularly interesting class of internally mixed particles is composed of aqueous salts solutions that are coated with organic surfactants which are molecules with long aliphatic chain and a water soluble end. Because these molecules tend to coat the particles' surfaces, a monolayer might be sufficient to drastically alter their hygroscopic properties, their CCN activity, and reactivity. The aliphatic chains, being exposed to the oxidizing atmosphere are expected to be transformed through heterogeneous chemistry, yielding complex products with mixed properties. We will report the results from a series of observations on ammonium sulfate, sodium chloride and sea salt particles coated with three types of surfactant molecules: sodium lauryl sulfate, sodium oleate and laurtrimonium chloride. We have been able to measure the effective densities of internally mixed particles with a range of surfactant concentration that start below a monolayer and extend all the way to particles composed of pure surfactant. For many of the measurements the data reveal a rather complex picture that cannot be simply interpreted in terms of the known pure-compound densities. For unsaturated hydrocarbons we observed and quantified the effect of oxidation by ozone on particle size, effective density and individual particle mass spectral signatures. One of the more important properties of these surfactants is that they can form a

Modulation of the wettability of excipients by surfactant and its impacts on the disintegration and release of tablets.

Science.gov (United States)

Yang, Baixue; Xu, Lu; Wang, Qiuxiao; Li, Sanming

2016-12-01

To investigate the modulation of the wettability of excipients by different types of surfactants and its impacts on the disintegration of tablets and drug release. The critical micelle concentration (CMC) of surfactants, including sodium dodecyl sulfate (SDS), sodium dodecyl benzene sulfonate (SDBS), dodecyl trimethyl ammonium bromide (DTAB), cetyltrimethyl ammonium bromide (CTAB) and polysorbate (Tween-20 and Tween-80), was obtained using the platinum ring method. Contact angles of surfactant solutions on the excipient compacts and double-distilled water on the mixture of surfactant and the other excipient (magnesium stearate (MgSt) or sodium alginate (SA)) were measured by the sessile drop technique. Besides, surface free energy of excipients was calculated by the Owens method. Finally, the disintegration of tablets and in vitro dissolution testing were performed according to the method described in USP. The wettability of excipients could be enhanced to different extent with low concentration of surfactant solutions and maintained stable basically after CMC. For MgSt (hydrophobic excipient), the shorter the hydrophobic chain (C 12 , including SDS and DTAB), the better the wettability with the addition of surfactant in the formulation, leading to the shorter disintegration time of tablets and higher drug release rate. In contrast, the wettability of SA (hydrophilic excipient) was reduced by adding surfactant, resulting in the longer disintegration time of tablets and lower release rate. The modulation of the wetting of pharmaceutical excipients by surfactant had changed the disintegration time of tablets and drug release rate to a greater extent.

Structure of DNA-Cationic Surfactant Complexes at Hydrophobically Modified and Hydrophilic Silica Surfaces as Revealed by Neutron Reflectometry

DEFF Research Database (Denmark)

Cardenas Gomez, Marite; Wacklin, Hanna; Campbell, Richard A.

2011-01-01

with dodecyltrimethylammonium bromide (DTAB) and hexadecyltrimethylammonium bromide (CTAB) on hydrophobic surfaces, where we show that DNA molecules are located on top of a self-assembled surfactant monolayer, with the thickness of the DNA layer and the surfactant DNA ratio determined by the surface coverage of the underlying...... interfacial structures, a higher concentration in relation to its cmc is required for the more soluble DTAB surfactant with a shorter alkyl chain than for CTAB. Our results suggest that the DNA Molecules Will spontaneously form a relatively dense, thin layer on top of a surfactant monolayer (hydrophobic...... surface) or a layer of admicelles (hydrophilic surface) as long as the surface concentration of surfactant is great enough to ensure a high interfacial-charge density. These findings have implications for bioanalytical and nanotechnology applications, which require the deposition of DNA layers with well...

The effect of surfactants on the electropolishing behavior of copper in orthophosphoric acid

Energy Technology Data Exchange (ETDEWEB)

Taha, A.A., E-mail: asia_taha@yahoo.com; Ahmed, A.M.; Rahman, H.H. Abdel; Abouzeid, F.M.

2013-07-15

The electropolishing behavior of copper was studied in orthophosphoric acid with Triton X-100, sodium dodecyl sulphate and cetyl pyridinium chloride as additives for improving the finish obtained on copper surface. This was investigated by measuring and comparing anode potential-limiting current relationships in solutions of gradually increasing concentration of surfactants. The addition of surfactants to the electropolishing solution results in a lower limiting current. This confirms the mass transport of dissolved species from the anode surface to the bulk of solution as the rate-determining step in the presence of three surfactants in all concentrations investigated. Scanning electron microscope (SEM), atomic force microscope (AFM) and measured brightness values were used to investigate the copper surface after electropolishing and the results were compared to polishing done in absence of surfactants. According to SEM images and brightness values, addition of Triton X-100 was effective to enhance levelling and brightening more than sodium dodecyl sulphate and cetyl pyridinium chloride. AFM analysis showed that the roughness values (R{sub a}) for an electropolished copper surface, in presence of surfactants, is significantly lower than in absence of surfactants. Different reaction conditions and the physical properties of solutions are studied to obtain dimensionless correlation among all these parameters.

Studies on interfacial tension and contact angle of synthesized surfactant and polymeric from castor oil for enhanced oil recovery

Science.gov (United States)

Babu, Keshak; Pal, Nilanjan; Bera, Achinta; Saxena, V. K.; Mandal, Ajay

2015-10-01

New synthesized polymeric surfactants have immensely attracted the researchers for further development of chemical enhanced oil recovery method particularly in surfactant flooding. Contact angle and interfacial tension measurement tests are the effective ways to identify proper chemicals/surfactants for enhanced oil recovery by chemical/surfactant flooding. In the present study a new polymeric surfactant was synthesized from pre-synthesized sodium methyl ester sulfonate (surfactant) and acrylamide for application in chemical enhanced oil recovery. The synthesized surfactant and polymeric surfactant were used to measure interfacial tension between their aqueous phase and crude oil phase to investigate the efficiency of the surfactants in reduction of interfacial tension. The synthesized polymeric surfactant has also ability to control the mobility because of its viscous nature in aqueous solution. Contact angles of solid-crude oil-surfactant interface were also measured to study the effect of the synthesized surfactant and polymeric surfactant on wettability alteration mechanism. Synergistic effect was studied by using NaCl and synthesized surfactants on interfacial tension. Dynamic interfacial tensions of the surfactant and polymeric surfactant solutions with crude oil were measured at different NaCl concentrations. Interfacial tension was found to be lowered up to 10-2 to 10-3 mN/m which is effective for oil recovery. Measurement of contact angle indicates the wettability change of the quartz surface. Comparative studies on efficiencies of synthesized sodium methyl ester sulfonate surfactant and polymeric surfactant were also carried out with respect to interfacial tension reduction and contact angle change.

Effect of fluid velocity, temperature, and concentration of non-ionic surfactants on drag reduction

International Nuclear Information System (INIS)

Cho, Sung-Hwan; Tae, Choon-Seob; Zaheeruddin, M.

2007-01-01

The drag reduction (DR) and heat transfer efficiency reduction (ER) of non-ionic surfactant as a function of fluid velocity, temperature, and surfactant concentration were investigated. Several types of new surfactants, which contain amine-oxide and betaine, were developed. An experimental apparatus consisting of two temperature controlled water storage tanks, pumps, test specimen pipe and the piping network, two flow meters, two pressure gauges, a heat exchanger, and data logging system was built. From the experimental results, it was concluded that existing alkyl ammonium surfactant (CTAC; cethyl trimethyl ammonium chloride) had DR of 0.6-0.8 at 1000-2000 ppm concentration with fluid temperature ranging between 50 and 60 o C. However, the DR was very low when the fluid temperature was 70-80 o C. The new amine oxide and betaine surfactant (SAOB; stearyl amine oxide + betaine) had lower DR at fluid temperatures ranging between 50 and 60 o C compared with CTAC. However, with fluid temperature ranging between 70 and 80 o C the DR was 0.6-0.8 when the concentration level was between 1000 and 2000 ppm

Tunable, antibacterial activity of silicone polyether surfactants.

Science.gov (United States)

Khan, Madiha F; Zepeda-Velazquez, Laura; Brook, Michael A

2015-08-01

Silicone surfactants are used in a variety of applications, however, limited data is available on the relationship between surfactant structure and biological activity. A series of seven nonionic, silicone polyether surfactants with known structures was tested for in vitro antibacterial activity against Escherichia coli BL21. The compounds varied in their hydrophobic head, comprised of branched silicone structures with 3-10 siloxane linkages and, in two cases, phenyl substitution, and hydrophilic tail of 8-44 poly(ethylene glycol) units. The surfactants were tested at three concentrations: below, at, and above their Critical Micelle Concentrations (CMC) against 5 concentrations of E. coli BL21 in a three-step assay comprised of a 14-24h turbidometric screen, a live-dead stain and viable colony counts. The bacterial concentration had little effect on antibacterial activity. For most of the surfactants, antibacterial activity was higher at concentrations above the CMC. Surfactants with smaller silicone head groups had as much as 4 times the bioactivity of surfactants with larger groups, with the smallest hydrophobe exhibiting potency equivalent to sodium dodecyl sulfate (SDS). Smaller PEG chains were similarly associated with higher potency. These data link lower micelle stability and enhanced permeability of smaller silicone head groups to antibacterial activity. The results demonstrate that simple manipulation of nonionic silicone polyether structure leads to significant changes in antibacterial activity. Copyright © 2015 Elsevier B.V. All rights reserved.

Assessment of primary eye and skin irritants by in vitro cytotoxicity and phototoxicity models: an in vitro approach of new arginine-based surfactant-induced irritation

International Nuclear Information System (INIS)

Benavides, T.; Mitjans, M.; Martinez, V.; Clapes, P.; Infante, M.R.; Clothier, R.H.; Vinardell, M.P.

2004-01-01

Extensive efforts have been made, recently, to find surfactants with lower irritation potential than those presently commercially available, for use in pharmaceutical and cosmetic preparations. Cytotoxic and phototoxic effects of a novel family of dicationic arginine-diglyceride surfactant compounds, 1,2-diacyl,3-O-(L-arginyl)-rac-glycerol with alkyl chain lengths in the range from 8 to 14 carbon atoms, were compared to three commercial surfactants. The end-points used to assess toxicity were the red blood cell lysis assay and uptake of the vital dye neutral red 24 h after dosing (NRU), respectively. Two immortalized cell lines, murine fibroblast cell line, 3T3, and one human keratinocyte cell line, HaCaT, were used as in vitro models to predict the potential phototoxicity which could result in irritation, determined by resazurin reduction to resorufin and neutral red uptake (NRU). All tested surfactants had cytotoxicity effects as demonstrated by and decrease of NR uptake, which showed a clear concentration-response relationship. Concentrations resulting in 50% inhibition of NR uptake (IC 50 ) range from 1 μmol l -1 (hexadecyl trimethyl ammonium bromide) to 565 μmol l -1 (12,12-L-arginine). Erythrocyte haemolysis also showed a clear concentration-response relationship, the 50% of haemolysis ranged from 37 μmol l -1 (10,10-L-arginine) to 151 μmol l -1 (sodium lauryl sulphate). Phototoxicity was performed with 12,12-L-acetyl-arginine, the most stable chemical structure. The validated 3T3 NRU photoxicity assay was used and revealed a phototoxic potential

The determination of the irritancy potential of surfactants using various methods of assessment.

Science.gov (United States)

Ciuchta, H P; Dodd, K T

1978-01-01

Several animal irritancy test methods whose criteria include sensory response, pain/discomfort or tissue damage were evaluated as to their ability to assess relative irritancy potential of the following surfactants: sodium lauryl polyether (12) sulfate (SLES), Miranol C2M (MC2M), Miranol MHT (MMHT), sodium coco methyl tauride (SCMT), triethanolamine lauryl sulfate (TEALS), ammonium lauryl sulfate (ALS) and sodium lauryl sulfate (SLS). Data from the mouse upper respiratory tract and mouse writhing tests indicated that SLES, MC2M and MMHT were the least irritating and SLS, ALS and TEALS were the most irritating. The blepharospasm test did not lend itself to this type of evaluation because sequential instillation of the surfactants produced eye anesthesia. Data from the Draize eye test indicated that SLES was the least irritating while MC2M was slightly more irritating. All other surfactants were equally irritating. The Draize skin test results showed that SLES again was the least irritating at all concentrations tested and that SLS and ALS along with TEALS and SCMT were the most irritating.

Jagannath Panda

Indian Academy of Sciences (India)

Home; Journals; Journal of Chemical Sciences. Jagannath Panda. Articles written in Journal of Chemical Sciences. Volume 112 Issue 6 December 2000 pp 615-622 Physical and Theoretical. Kinetic investigation of the oxidation of N-alkyl anilines by peroxomonophosphoric acid in anionic surfactant sodium lauryl sulphate.

Read-across of ready biodegradability based on the substrate specificity of N-alkyl polypropylene polyamine-degrading microorganisms.

Science.gov (United States)

Geerts, R; van Ginkel, C G; Plugge, C M

2017-04-01

The biodegradation of N-alkyl polypropylene polyamines (NAPPs) was studied using pure and mixed cultures to enable read-across of ready biodegradability test results. Two Pseudomonas spp. were isolated from activated sludge with N-oleyl alkyl propylene diamine and N-coco alkyl dipropylene triamine, respectively. Both strains utilized all NAPPs tested as the sole source of carbon, nitrogen and energy for growth. Mineralization of NAPPs was independent of the alkyl chain length and the size of the polyamine moiety. NAPPs degraded in closed bottle tests (CBTs) using both river water and activated sludge. However, ready biodegradability of NAPPs with alkyl chain lengths of 16-18 carbon atoms and polyamine moieties with three and four nitrogen atoms could not be demonstrated. Biodegradation in the CBT was hampered by their limited bioavailability, making assessment of the true ready biodegradability of these highly adsorptive surfactants impossible. All NAPPs are therefore classified as readily biodegradable through read-across. Read-across is justified by the broad substrate specificity of NAPP-degrading microorganisms, their omnipresence and the mineralization of NAPPs.

Antimicrobial Activity of Single-Walled Carbon Nano tubes Suspended in Different Surfactants

International Nuclear Information System (INIS)

Dong, L.; Alex Henderson, A.; Field, Ch.

2012-01-01

We investigated the antibacterial activity of single-walled carbon nano tubes (SWCNTs) dispersed in surfactant solutions of sodium cholate, sodium dodecylbenzene sulfonate, and sodium dodecyl sulfate. Among the three surfactants, sodium cholate demonstrated the weakest antibacterial activity against Salmonella enterica, Escherichia coli, and Enterococcus faecium and thereby was used to disperse bundled SWCNTs in order to study nano tube antibiotic activity. SWCNTs exhibited antibacterial characteristics for both S. enterica and E. coli. With the increase of nano tube concentrations from 0.3 mg/mL to 1.5 mg/mL, the growth curves had plateaus at lower absorbance values whereas the absorbance value was not obviously affected by the incubation ranging from 5?min to 2 h. Our findings indicate that carbon nano tubes could become an effective alternative to antibiotics in dealing with drug-resistant and multidrug-resistant bacterial strains because of the physical mode of bactericidal action that SWCNTs display

Surfactant use with nitrate-based bioremediation

International Nuclear Information System (INIS)

Wilson, B.H.; Hutchins, S.R.; West, C.C.

1995-01-01

This study presents results of an initial survey on the effect of six surfactants on the biodegradation of petroleum hydrocarbons in bioremediation applications using nitrate as the electron acceptor. Aquifer material from Park City, Kansas, was used for the study. The three atomic surfactants chosen were Steol CS-330, Dowfax 8390 and sodium dodecylbenzene sulfonate (SDBS); the three nonionic surfactants were T-MAZ-60, Triton X-100, and Igepal CO-660. Both Steol CS-330 and T-MAZ-60 biodegraded under denitrifying conditions. The Steol inhibited biodegradation of benzene, toluene, ethylbenzene, xylenes, and trimethylbenzenes (BTEXTMB). Only toluene was rapidly degraded in the presence of T-MAZ-60. Biodegradation of all compounds, including toluene, appears to be inhibited by Dowfax 8390 and SDBS. No biodegradation of Dowfax 8390 or SDBS was observed. SDBS inhibited denitrification, but Dowfax 8390 did not. For the microcosms containing Triton X-100 or Igepal CO-660, removal of toluene, ethylbenzene, m-xylene, 1,3,5-TMB, and 1,2,4-TMB were similar to their removals in the no-surfactant treatment. These two surfactants did not biodegrade, did not inhibit biodegradation of the alkylbenzenes, and did not inhibit denitrification. Further studies are continuing with aquifer material from Eglin Air Force Base

Foaming behaviour of polymer-surfactant solutions

International Nuclear Information System (INIS)

Cervantes-MartInez, Alfredo; Maldonado, Amir

2007-01-01

We study the effect of a non-ionic amphiphilic polymer (PEG-100 stearate also called Myrj 59) on the foaming behaviour of aqueous solutions of an anionic surfactant (sodium dodecyl sulfate or SDS). The SDS concentration was kept fixed while the Myrj 59 concentration was varied. Measurements of foamability, surface tension and electrical conductivity were carried out. The results show two opposite effects depending on the polymer concentration: foamability is higher when the Myrj 59 concentration is low; however, it decreases considerably when the polymer concentration is increased. This behaviour is due to the polymer adsorption at the air/liquid interface at lower polymer concentrations, and to the formation of a polymer-surfactant complex in the bulk at higher concentrations. The results are confirmed by surface tension and electrical conductivity measurements, which are interpreted in terms of the microstructure of the polymer-surfactant solutions. The observed behaviour is due to the amphiphilic nature of the studied polymer. The increased hydrophobicity of Myrj 59, compared to that of water-soluble polymers like PEG or PEO, increases its 'reactivity' towards SDS, i.e. the strength of its interaction with this anionic surfactant. Our results show that hydrophobically modified polymers have potential applications as additives in order to control the foaming properties of surfactant solutions

Kinetics of Surfactant Desorption at an Air–Solution Interface

KAUST Repository

Morgan, C. E.; Breward, C. J. W.; Griffiths, I. M.; Howell, P. D.; Penfold, J.; Thomas, R. K.; Tucker, I.; Petkov, J. T.; Webster, J. R. P.

2012-01-01

The kinetics of re-equilibration of the anionic surfactant sodium dodecylbenzene sulfonate at the air-solution interface have been studied using neutron reflectivity. The experimental arrangement incorporates a novel flow cell in which the subphase

Adsorption properties of biologically active derivatives of quaternary ammonium surfactants and their mixtures at aqueous/air interface. I. Equilibrium surface tension, surfactant aggregation and wettability.

Science.gov (United States)

Rojewska, Monika; Biadasz, Andrzej; Kotkowiak, Michał; Olejnik, Anna; Rychlik, Joanna; Dudkowiak, Alina; Prochaska, Krystyna

2013-10-01

The adsorption properties of surfactant mixtures containing two types of quaternary derivatives of lysosomotropic substances: alkyl N,N-dimethylalaninates methobromides and alkyl N,N-dimethylglycinates methobromides were studied. Quantitative and qualitative description of the adsorption process was carried out on the basis of experimentally obtained equilibrium surface tension isotherms. The results indicated that most of the systems studied revealed synergistic effect both in adsorption and wetting properties. In vitro studies on human cancer cells were undertaken and the data obtained showed that the mixtures suppressed the cancer cells' proliferation more effectively than individual components. Results of preliminary research on the interaction of catanionic mixtures with phospholipids suggested a possibility of a strong penetration of cell membranes by the mixtures investigated. Copyright © 2013 Elsevier B.V. All rights reserved.

An Experimental Study of Alkali-surfactant-polymer Flooding through Glass Micromodels Including Dead-end Pores

Directory of Open Access Journals (Sweden)

Mohsen Esmaeili

2013-07-01

Full Text Available Chemical flooding, especially alkaline/surfactant/polymer flooding, is of increasing interest due to the world increasing oil demand. This work shows the aspects of using alkaline/surfactant/polymer as an enhanced oil recovery method in the porous media having a high dead-end pore frequency with various dead-end pore parameters (such as opening, depth, aspect ratio, and orientation. Using glass micromodels makes it possible to manipulate and analyze the pore parameters and watch through the porous media precisely. The results show that polyacrylamide almost always enhances oil production recovery factor (up to 14% in comparison with brine injection in this kind of porous media. Except at low concentrations of polyacrylamide and sodium carbonate, sodium dodecyl sulfonate improves oil recovery (even 15% in the case of high polyacrylamide concentration and low sodium carbonate concentration. Increasing alkaline concentration reduces recovery factor except at low concentrations of polyacrylamide and high concentrations of surfactant.

Cytotoxicity Effects of Different Surfactant Molecules Conjugated to Carbon Nanotubes on Human Astrocytoma Cells

Science.gov (United States)

Dong, Lifeng; Witkowski, Colette M.; Craig, Michael M.; Greenwade, Molly M.; Joseph, Katherine L.

2009-12-01

Phase contrast and epifluorescence microscopy were utilized to monitor morphological changes in human astrocytoma cells during a time-course exposure to single-walled carbon nanotube (SWCNT) conjugates with different surfactants and to investigate sub-cellular distribution of the nanotube conjugates, respectively. Experimental results demonstrate that cytotoxicity of the nanotube/surfactant conjugates is related to the toxicity of surfactant molecules attached on the nanotube surfaces. Both sodium dodecyl sulfate (SDS) and sodium dodecylbenzene sulfonate (SDBS) are toxic to cells. Exposure to CNT/SDS conjugates (0.5 mg/mL) for less than 5 min caused changes in cell morphology resulting in a distinctly spherical shape compared to untreated cells. In contrast, sodium cholate (SC) and CNT/SC did not affect cell morphology, proliferation, or growth. These data indicate that SC is an environmentally friendly surfactant for the purification and dispersion of SWCNTs. Epifluorescence microscopy analysis of CNT/DNA conjugates revealed distribution in the cytoplasm of cells and did not show adverse effects on cell morphology, proliferation, or viability during a 72-h incubation. These observations suggest that the SWCNTs could be used as non-viral vectors for diagnostic and therapeutic molecules across the blood-brain barrier to the brain and the central nervous system.

Ruthenium-Catalyzed Alkylation of Oxindole with Alcohols

DEFF Research Database (Denmark)

Jensen, Thomas; Madsen, Robert

2009-01-01

An atom-economical and solvent-free catalytic procedure for the mono-3-alkylation of oxindole with alcohols is described. The reaction is mediated by the in situ generated catalyst from RuCl3 center dot xH(2)O and PPh3 in the presence of sodium hydroxide, The reactions proceed in good to excellent...... yields with a wide range of aromatic, heteroaromatic, and aliphatic alcohols....

Controlling block copolymer phase behavior using ionic surfactant

Energy Technology Data Exchange (ETDEWEB)

Ray, D.; Aswal, V. K. [Solid State Physics Division, Bhabha Atomic Research Centre, Mumbai 400 085, India E-mail: debes.phys@gmail.com (India)

2016-05-23

The phase behavior of poly(ethylene oxide)-poly(propylene oxide-poly(ethylene oxide) PEO-PPO-PEO triblock copolymer [P85 (EO{sub 26}PO{sub 39}EO{sub 26})] in presence of anionic surfactant sodium dodecyl sulfate (SDS) in aqueous solution as a function of temperature has been studied using dynamic light scattering (DLS) and small-angle neutron scattering (SANS). The measurements have been carried out for fixed concentrations (1 wt%) of block copolymer and surfactants. Each of the individual components (block copolymer and surfactant) and the nanoparticle–surfactant mixed system have been examined at varying temperature. The block copolymer P85 forms spherical micelles at room temperature whereas shows sphere-to-rod like micelle transition at higher temperatures. On the other hand, SDS surfactant forms ellipsoidal micelles over a wide temperature range. Interestingly, it is found that phase behavior of mixed micellar system (P85 + SDS) as a function of temperature is drastically different from that of P85, giving the control over the temperature-dependent phase behavior of block copolymers.

Degradation of anionic surfactants using the reactor based on dielectric barrier discharge

Directory of Open Access Journals (Sweden)

Aonyas Munera Mustafa

2016-01-01

Full Text Available Two anionic surfactants (sodium lauryl sulfate - SDS and sodium dodecylbenzenesulfonate - SDBS were treated with dielectric barrier discharge. Loss of surfactant activity, decrease of chemical oxygen demand and total organic carbon as well as lower toxicity of degradation products were determined. Effects of catalysts - hydrogen peroxide and iron (II, on parameters mentioned above, were determined. Catalysts affect the degradation of SDBS and in the case of SDS catalysts have no effect on degradation. Both catalysts induce the decrease of COD and TOC values. Toxicity of solutions after the plasma treatment is lower in all the systems tested. [Projekat Ministarstva nauke Republike Srbije, br. OI 172030

Influence of surfactants in forced dynamic dewetting.

Science.gov (United States)

Henrich, Franziska; Fell, Daniela; Truszkowska, Dorota; Weirich, Marcel; Anyfantakis, Manos; Nguyen, Thi-Huong; Wagner, Manfred; Auernhammer, Günter K; Butt, Hans-Jürgen

2016-09-20

In this work we show that the forced dynamic dewetting of surfactant solutions depends sensitively on the surfactant concentration. To measure this effect, a hydrophobic rotating cylinder was horizontally half immersed in aqueous surfactant solutions. Dynamic contact angles were measured optically by extrapolating the contour of the meniscus to the contact line. Anionic (sodium 1-decanesulfonate, S-1DeS), cationic (cetyl trimethylammonium bromide, CTAB) and nonionic surfactants (C 4 E 1 , C 8 E 3 and C 12 E 5 ) with critical micelle concentrations (CMCs) spanning four orders of magnitude were used. The receding contact angle in water decreased with increasing velocity. This decrease was strongly enhanced when adding surfactant, even at surfactant concentrations of 10% of the critical micelle concentration. Plots of the receding contact angle-versus-velocity almost superimpose when being plotted at the same relative concentration (concentration/CMC). Thus the rescaled concentration is the dominating property for dynamic dewetting. The charge of the surfactants did not play a role, thus excluding electrostatic effects. The change in contact angle can be interpreted by local surface tension gradients, i.e. Marangoni stresses, close to the three-phase contact line. The decrease of dynamic contact angles with velocity follows two regimes. Despite the existence of Marangoni stresses close to the contact line, for a dewetting velocity above 1-10 mm s -1 the hydrodynamic theory is able to describe the experimental results for all surfactant concentrations. At slower velocities an additional steep decrease of the contact angle with velocity was observed. Particle tracking velocimetry showed that the flow profiles do not differ with and without surfactant on a scales >100 μm.

Thermodynamics of self-assembling of mixture of a cationic gemini surfactant and sodium dodecylsulfate in aqueous solution: Calorimetry, conductivity and surface pressure measurements

International Nuclear Information System (INIS)

Bai, Guangyue; Wang, Yujie; Ding, Yanhong; Zhuo, Kelei; Wang, Jianji; Bastos, Margarida

2016-01-01

Highlights: • ITC provided thermodynamic characterization of self-association of oppositely charged gemini/SDS surfactants. • Phase transitions and corresponding enthalpies were obtained by ITC. • The transitions reflect a change in morphology, supported by Cryo-TEM images. • Conductivity and ITC results show very good agreement. • An asymmetric distribution of surfactants in the aggregates is supported by results. - Abstract: The thermodynamics and phase behavior of mixtures of cationic gemini surfactant decanediyl-α,ω-bis(dodecyldimethylammonium bromide) (12-10-12) and sodium dodecylsulfate (SDS) were studied in the dilute SDS-rich region. The enthalpy of interaction between both surfactant monomers before the critical micelle concentration for the mixture (cmc_m_i_x) was determined by isothermal titration calorimetry (ITC). After the cmc_m_i_x, ITC results exhibited a first process associated with a large endothermic enthalpy change followed by a second one with a very small exothermic enthalpy change. In the same regions, the conductivity curves show an increase in slope after the break, followed by a plateau region, respectively for the two processes. The combined results from the various methodologies used lead us to propose that the first process reflects the formation of non-spherical micelles and the second one the vesicle formation. The area per catanionic complex was obtained through surface pressure measurements, leading to an apparent packing parameter ⩾1. The observed behavior may be rationalized on the basis of the hypothesis that both surfactants distribute asymmetrically in the vesicle bilayers and unevenly in the non-spherical micelle. In order to get structural information Cryo-TEM experiments were performed, which provided images that support this interpretation. From all the information gathered a phase diagram was mapped, including three one-phase regions of spherical micelles, non-spherical micelles and vesicles.

Adsorption and Surfactant-Mediated Desorption of Poly(vinylpyrrolidone) on Plasma- and Piranha-Cleaned Silica Surfaces

NARCIS (Netherlands)

de Vos, Wiebe Matthijs; Cattoz, B.; Avery, M.P.; Cosgrove, T.; Prescott, S.W.

2014-01-01

Optical flow cell reflectometry was used to study the adsorption of poly(vinylpyrrolidone) (PVP) to a silica surface and the subsequent surfactant adsorption and polymer desorption upon exposure to the anionic surfactant sodium dodecyl sulfate (SDS). We have studied these effects as a function of pH

Polyfluorinated surfactants (PFS) in paper and board coatings for food packaging

DEFF Research Database (Denmark)

Trier, Xenia; Granby, Kit; Christensen, Jan H

2011-01-01

sulfonamide N-alkyl esters were analysed. Di- and trialkylated PAPS and S-diPAPS were found in migrates from European food contact materials. Conclusion This study highlights the need to monitor for more types of PFS in order to map the sources of PFAS in humans and the environment.......range of polyfluorinated surfactants (PFS) used for food contact materials, primarily to impart oil and water repellency on paper and board. PFS are of interest, as they can be precursors of poly- and perfluorinated alkyl substances (PFAS), of which several are persistent and are found worldwide...... in human blood and in the environment. Materials and methods To determine the elemental composition of PFS, we combined information from patents, chemical suppliers and analyses of industrial blends using ultra performance liquid chromatography-negative electrospray ionisation quadrupole time...

ASSOCIATION OF BRANCHED POLYETHYLENE IMINE WITH SURFACTANTS IN AQUEOUS SOLUTION

Directory of Open Access Journals (Sweden)

Ismael C. Bellettini

2015-07-01

Full Text Available Three polymer-surfactant systems comprised of branched polyethylene imine (PEI with an anionic surfactant (sodium dodecylsulfate; SDS, a cationic surfactant (tetradecyltrimethylammonium bromide; TTAB, and a zwitterionic surfactant (N-tetradecyl-N,N-dimethyl-3-ammonio-1-propanesulfonate; SB3-14 were studied based on the properties of surface tension, pyrene fluorescence emission, dynamic light scattering, pH, and zeta potential measurements. The critical aggregation concentration (cac and polymer saturation point (psp were determined for all three systems. The effect of these surfactants on the physico-chemical characteristics (diameter and surface charge of the complexes formed was determined. Polymer-surfactant interactions occurred in all of the systems studied, with the strongest interactions, electrostatic in nature, occurring in the SDS-PEI system. After the neutralization of the polymer charges with the addition of the surfactant, the hydrophobic effect started to control the interlacing of the polymer chains. For the PEI-TTAB system, a very dense film was formed at surfactant concentrations above 2.0 mmol L-1. In this case, the bromide counter-ion interacted with both the positively-charged PEI and the head of the surfactant, which is responsible for the formation of double layer coordination complexes. For the system composed of PEI and the zwitterionic surfactant, less cooperative associations occurred in comparison with the other systems.

Probing dynamics and mechanism of exchange process of quaternary ammonium dimeric surfactants, 14-s-14, in the presence of conventional surfactants.

Science.gov (United States)

Liu, Jun; Jiang, Yan; Chen, Hong; Mao, Shi Zhen; Du, You Ru; Liu, Mai Li

2012-12-27

In this Article, we investigated effects of different types of conventional surfactants on exchange dynamics of quaternary ammonium dimeric surfactants, with chemical formula C(14)H(29)N(+)(CH(3))(2)- (CH(2))(s)-N(+)(CH(3))(2)C(14)H(29)·2Br(-), or 14-s-14 for short. Two nonionic surfactants, TritonX-100 (TX-100) and polyethylene glycol (23) laurylether (Brij-35), and one cationic surfactant, n-tetradecyltrimethyl ammonium bromide (TTAB), and one ionic surfactant, sodium dodecyl sulfate (SDS) were chosen as typical conventional surfactants. Exchange rates of 14-s-14 (s = 2, 3, and 4) between the micelle form and monomer in solution were detected by two NMR methods: one-dimensional (1D) line shape analysis and two-dimensional (2D) exchange spectroscopy (EXSY). Results show that the nonionic surfactants (TX-100 and Brij-35), the cationic surfactant (TTAB), and the ionic surfactant (SDS) respectively accelerated, barely influenced, and slowed the exchange rate of 14-s-14. The effect mechanism was investigated by the self-diffusion experiment, relaxation time measurements (T(2)/T(1)), the fluorescence experiment (I(1)/I(3)) and observed chemical shift variations. Results reveal that, nonionic conventional surfactants (TX-100 and Brij-35) loosened the molecule arrangement and decreased hydrophobic interactions in the micelle, and thus accelerated the exchange rate of 14-s-14. The cationic conventional surfactant (TTAB) barely changed the molecule arrangement and thus barely influenced the exchange rate of 14-s-14. The ionic conventional surfactant (SDS) introduced the electrostatic attraction effect, tightened the molecule arrangement, and increased hydrophobic interactions in the micelle, and thus slowed down the exchange rate of 14-s-14. Additionally, the two-step exchange mechanism of 14-s-14 in the mixed solution was revealed through interesting variation tendencies of exchange rates of 14-s-14.

Comparative evaluation of antibacterial property and substantivity of chlorhexidine containing dentifrices with sodium lauryl sulfate and Tween as surfactants: an in vivo study.

Science.gov (United States)

Venu, V; Prabhakar, A R; Basappa, N

2013-01-01

The aim of the study was to determine the antibacterial property and substantivity of chlorhexidine containing dentifrices with sodium lauryl sulfate (SLS) and Tween as surfactants. It is a double-blind cross over the study, a total of 20 children within their mixed dentition period (7-13 year) having Streptococci mutans count more than 10(6) were selected for the main study. Three types of chlorhexidine containing dentifrices were used with a washout period of 1 week. Out of the three toothpastes, one was without surfactant and other two toothpastes contained SLS and Tween as surfactants respectively. 20 volunteers brushed for 1 min during the study day with their assigned toothpaste. Saliva samples were collected before brushing, immediately after brushing and 1, 3, 5, and 7 hand sent for microbial analysis. The culture carried out by inoculating saliva sample onto Mitis salivarius agar for selective isolation of S. mutans followed by counting of colony forming unit. Group I and III (Chlorhexidine and CHX + Tween) had shown statistically significant reduction in bacterial count until 7 h when compared to their baseline values ( P < 0.001). Group II toothpaste (CHX + SLS) had shown significant reduction in bacterial count until 3 h only. On inter group comparison, Group III had shown good amount of percentage reduction in bacterial count when compared to other groups. CHX + Tween toothpaste had shown statistically significant reduction in antibacterial activity and substantivity than other groups. These findings show chlorhexidine containing toothpaste with non-ionic surfactant will be able to maintain the antibacterial property and substantivity of chlorhexidine.

Study on the Alkylation Reactions of N(7)-Unsubstituted 1,3-Diazaoxindoles.

Science.gov (United States)

Kókai, Eszter; Halász, Judit; Dancsó, András; Nagy, József; Simig, Gyula; Volk, Balázs

2017-05-19

The chemistry of the 5,7-dihydro-6 H -pyrrolo[2,3- d ]pyrimidin-6-one (1,3-diazaoxindole) compound family, possessing a drug-like scaffold, is unexplored. In this study, the alkylation reactions of N (7)-unsubstituted 5-isopropyl-1,3-diazaoxindoles bearing various substituents at the C (2) position have been investigated. The starting compounds were synthesized from the C (5)-unsubstituted parent compounds by condensation with acetone and subsequent catalytic reduction of the 5-isopropylidene moiety. Alkylation of the thus obtained 5-isopropyl derivatives with methyl iodide or benzyl bromide in the presence of a large excess of sodium hydroxide led to 5,7-disubstituted derivatives. Use of butyllithium as the base rendered alkylation in the C (5) position possible with reasonable selectivity, without affecting the N (7) atom. During the study on the alkylation reactions, some interesting by-products were also isolated and characterized.

MICROEMULSION OF MIXED CHLORINATED SOLVENTS USING FOOD GRADE (EDIBLE) SURFACTANTS

Science.gov (United States)

Ground water contamination frequently consists of mixed chlorinated solvents [e.g., tetrachloroethylene (PCE), trichloroethylene (TCE), and trans-1,2- dichloroethylene (DCE)]. In this research, mixtures of the food grade (edible) surfactants bis(2-ethylhexyl) sodium sulfosuccinat...

Dilational viscoelastic properties of fluid interfaces - III mixed surfactant systems

Energy Technology Data Exchange (ETDEWEB)

Djabbarah, N.F.; Wasan, D.T.

1982-01-01

The surface viscosity and elasticity of solutions of mixed surfactants were determined using the longitudinal wave technique combined with tracer particle measurements. The recent analysis of Maru et al., which was restricted to insoluble monolayers and to monolayers adsorbed from a single surfactant solution, has now been extended to multicomponent solutions. This analysis can be used not only to estimate the ''net'' viscoelastic properties at gas-liquid interfaces but also to estimate the composition as well as the intrinsic viscoelastic properties. Furthermore, when accompanied by separate measurements of shear viscoelastic properties, the above analysis can be used for the determination of dilational viscosity and elasticity. Surface viscoelasticity measurements were conducted on aqueous solutions of sodium lauryl sulfate and sodium lauryl sulfate-lauryl alcohol. Net surface viscosity and elasticity of sodium lauryl sulfate solutions increased with bulk concentration and reached a maximum at a concentration in the neighborhood of the critical micelle concentration. The presence of small amount of lauryl alcohol caused almost an order of magnitude increase in intrinsic surface viscosity and a similar increase in compositional surface elasticity. A comparison between the values of intrinsic surface viscosity and those of surface shear viscosity indicated that surface dilational viscosity exceeds surface shear viscosity by at least two orders of magnitude. These appear to be the first set of data presented hitherto for the surface dilational properties in addition to surface shear properties for the same mixed surfactant systems.

Effects of various surfactants on the dispersion stability and electrical conductivity of surface modified graphene

Energy Technology Data Exchange (ETDEWEB)

Uddin, Md. Elias [WCU Program, Department of BIN Fusion Technology, Chonbuk National University, Jeonju, Jeonbuk 561-756 (Korea, Republic of); Kuila, Tapas [Surface Engineering and Tribology, CSIR – Central Mechanical Engineering Research Institute, Durgapur 721 302 (India); Nayak, Ganesh Chandra [Department of Applied Chemistry, ISM Dhanbad, Dhanbad 826 004, Jharkhand (India); Kim, Nam Hoon [Department of Hydrogen and Fuel Cell Engineering, Chonbuk National University, Jeonju, Jeonbuk 561-756 (Korea, Republic of); Ku, Bon-Cheol [Institute of Advanced Composite Materials, Korea Institute of Science and Technology, Dunsan-ri, Bongdong-eup, Wanju-gun, Jeollabuk-do 864-9 (Korea, Republic of); Lee, Joong Hee, E-mail: jhl@chonbuk.ac.kr [WCU Program, Department of BIN Fusion Technology, Chonbuk National University, Jeonju, Jeonbuk 561-756 (Korea, Republic of); Department of Hydrogen and Fuel Cell Engineering, Chonbuk National University, Jeonju, Jeonbuk 561-756 (Korea, Republic of)

2013-06-15

Highlights: ► Water dispersible graphene has been prepared using ionic and non-ionic surfactants. ► XPS and FTIR spectra analysis confirm surface modification and reduction of GO. ► The highest water dispersibility is observed in the graphene modified with of SDBS. ► The best properties of modified graphene is achieved with GO/surfactant ratio of two. -- Abstract: Ionic and non-ionic surfactant functionalized, water dispersible graphene were prepared to investigate the effects on the dispersion stability and electrical conductivity of graphene. In this study, sodium dodecyl benzene sulfonate (SDBS), sodium dodecyl sulfate and 4-(1,1,3,3-tetramethylbutyl) phenyl-polyethylene glycol (Triton X-100) were used as ionic and non-ionic surfactants. The effects of surfactant concentrations on the dispersibility and electrical conductivity of the surface modified graphene were investigated. The dispersion stability of SDBS functionalized graphene (SDBS-G) was found to be best in water at 1.5 mg ml{sup −1}. X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy analysis indicate that the presence of surfactants does not prevent the reduction of graphene oxide (GO). These measurements also demonstrated that the surfactants were present on the surface of graphene, resulting in the formation of functionalized graphene. The thickness of different functionalized graphene was measured by Atomic force microscopy and varied significantly with different surfactants. The thermal properties of the functionalized graphene were also found to be dependent on the nature of the surfactants. The electrical conductivity of SDBS-G (108 S m{sup −1}) was comparatively higher than SDS and Triton X-100 functionalized graphene.

Biodegradability of bacterial surfactants.

Science.gov (United States)

Lima, Tânia M S; Procópio, Lorena C; Brandão, Felipe D; Carvalho, André M X; Tótola, Marcos R; Borges, Arnaldo C

2011-06-01

This work aimed at evaluating the biodegradability of different bacterial surfactants in liquid medium and in soil microcosms. The biodegradability of biosurfactants by pure and mixed bacterial cultures was evaluated through CO(2) evolution. Three bacterial strains, Acinetobacter baumanni LBBMA ES11, Acinetobacter haemolyticus LBBMA 53 and Pseudomonas sp. LBBMA 101B, used the biosurfactants produced by Bacillus sp. LBBMA 111A (mixed lipopeptide), Bacillus subtilis LBBMA 155 (lipopeptide), Flavobacterium sp. LBBMA 168 (mixture of flavolipids), Dietzia Maris LBBMA 191(glycolipid) and Arthrobacter oxydans LBBMA 201(lipopeptide) as carbon sources in minimal medium. The synthetic surfactant sodium dodecyl sulfate (SDS) was also mineralized by these microorganisms, but at a lower rate. CO(2) emitted by a mixed bacterial culture in soil microcosms with biosurfactants was higher than in the microcosm containing SDS. Biosurfactant mineralization in soil was confirmed by the increase in surface tension of the soil aqueous extracts after incubation with the mixed bacterial culture. It can be concluded that, in terms of biodegradability and environmental security, these compounds are more suitable for applications in remediation technologies in comparison to synthetic surfactants. However, more information is needed on structure of biosurfactants, their interaction with soil and contaminants and scale up and cost for biosurfactant production.

Polycation-sodium lauryl ether sulfate-type surfactant complexes: influence of ethylene oxide length.

Science.gov (United States)

Vleugels, Leo F W; Pollet, Jennifer; Tuinier, Remco

2015-05-21

Polyelectrolyte-surfactant complexes (PESC) are a class of materials which form spontaneously by self-assembly driven by electrostatic and hydrophobic interactions. PESC containing sodium lauryl ether sulfates (SLES) have found wide application in hair care products like shampoo. Typically, SLES with only one or two ethylene oxide (EO) groups are used for this application. We have studied the influence of the size of the EO block (ranging from 0 to 30 EO groups) on complexation with two model polycations: linear polyDADMAC and branched PEI. PESC size and electrostatic properties were determined during stepwise titration of buffered polycation solutions. The critical aggregation concentration (CAC) of PESC was determined by surface tension measurements and fluorescence spectroscopy. For polyDADMAC, there is no influence of the size of the EO block on the complexation behavior; the stiff polycation governs the structure formation. For PEI, it was seen that the EO block size does affect the structure of the complexes. The CAC value of the investigated complexes turns out to be rather independent of the EO block size; however, the CMC/CAC ratio decreases with increasing size of the EO block. This latter observation explains why the Lochhead-Goddard effect is most effective for small EO blocks.

Antioxidant poly(lactic-co-glycolic) acid nanoparticles made with α-tocopherol-ascorbic acid surfactant.

Science.gov (United States)

Astete, Carlos E; Dolliver, Debra; Whaley, Meocha; Khachatryan, Lavrent; Sabliov, Cristina M

2011-12-27

The goal of the study was to synthesize a surfactant made of α-tocopherol (vitamin E) and ascorbic acid (vitamin C) of antioxidant properties dubbed as EC, and to use this surfactant to make poly(lactic-co-glycolic) acid (PLGA) nanoparticles. Self-assembled EC nanostructures and PLGA-EC nanoparticles were made by nanoprecipitation, and their physical properties (size, size distribution, morphology) were studied at different salt concentrations, surfactant concentrations, and polymer/surfactant ratios. EC surfactant was shown to form self-assembled nanostructures in water with a size of 22 to 138 nm in the presence of sodium chloride, or 12 to 31 nm when synthesis was carried out in sodium bicarbonate. Polymeric PLGA-EC nanoparticles presented a size of 90 to 126 nm for 40% to 120% mass ratio PLGA to surfactant. For the same mass ratios, the PLGA-Span80 formed particles measured 155 to 216 nm. Span80 formed bilayers, whereas EC formed monolayers at the interfaces. PLGA-EC nanoparticles and EC showed antioxidant activity based on 2,2-diphenyl-1-picrylhydrazyl (DPPH) radical scavenging assay measurements using UV and EPR techniques, antioxidant activity which is not characteristic to commercially available Span80. The thiobarbituric acid reactive substances (TBARS) assay for lipid peroxidation showed that PLGA nanoparticles with EC performed better as antioxidants than the EC nanoassembly or the free vitamin C. Nanoparticles were readily internalized by HepG2 cells and were localized in the cytoplasm. The newly synthesized EC surfactant was therefore found successful in forming uniform, small size polymeric nanoparticles of intrinsic antioxidant properties.

Surfactant adsorption study in sandstone for enhanced oil recovery; Estudo da adsorcao de tensoativos em arenitos para recuperacao avancada de petroleo

Energy Technology Data Exchange (ETDEWEB)

Curbelo, Fabiola D.S.; Santanna, Vanessa C.; Barros Neto, Eduardo L. de; Dutra Junior, Tarcilio V.; Dantas Neto, Afonso A. [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil). Dept. de Engenharia Quimica; Garnica, Alfredo I.C. [Universidade Federal da Paraiba (UFPB), Joao Pessoa, PB (Brazil). Dept. de Tecnologia Quimica e de Alimentos; Lucena Neto, Marciano [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil); Dantas, Tereza N.C. [Faculdade Natalense para o Desenvolvimento do RN (FARN), Natal, RN (Brazil)

2004-07-01

Adsorption of surfactants from aqueous solutions in porous media is very important in Enhanced Oil Recovery (EOR) of oil reservoirs because surfactant loss due to adsorption on the reservoir rocks weakens the effectiveness of the injected chemical slug in reducing oil-water tension (IFT) and makes the process uneconomical. In this paper, two nonionic surfactants, such as alkyl phenol polyoxyethylene, with different ethoxylation degrees were studied, ENP95 and ENP150. The results of flow experiments of surfactant solutions in porous media showed that adsorption was higher for ENP95 because it has smaller ethoxylation degree than ENP150. This occurs what with increasing length of the head group, the molecules become more hydrophilic and, in associated structures, the steric hindrance between the head groups increases. Generally speaking, adsorption appears to be a cooperative process involving lateral interaction between surfactant and weak interaction with the solid surface. (author)

Comparative evaluation of antibacterial property and substantivity of chlorhexidine containing dentifrices with sodium lauryl sulfate and Tween as surfactants: An in vivo study

Directory of Open Access Journals (Sweden)

V Venu

2013-01-01

Full Text Available Aim: The aim of the study was to determine the antibacterial property and substantivity of chlorhexidine containing dentifrices with sodium lauryl sulfate (SLS and Tween as surfactants. Materials and Methods: It is a double-blind cross over the study, a total of 20 children within their mixed dentition period (7-13 year having Streptococci mutans count more than 10 6 were selected for the main study. Three types of chlorhexidine containing dentifrices were used with a washout period of 1 week. Out of the three toothpastes, one was without surfactant and other two toothpastes contained SLS and Tween as surfactants respectively. 20 volunteers brushed for 1 min during the study day with their assigned toothpaste. Saliva samples were collected before brushing, immediately after brushing and 1, 3, 5, and 7 hand sent for microbial analysis. The culture carried out by inoculating saliva sample onto Mitis salivarius agar for selective isolation of S. mutans followed by counting of colony forming unit. Results: Group I and III (Chlorhexidine and CHX + Tween had shown statistically significant reduction in bacterial count until 7 h when compared to their baseline values ( P < 0.001. Group II toothpaste (CHX + SLS had shown significant reduction in bacterial count until 3 h only. On inter group comparison, Group III had shown good amount of percentage reduction in bacterial count when compared to other groups. Conclusion: CHX + Tween toothpaste had shown statistically significant reduction in antibacterial activity and substantivity than other groups. These findings show chlorhexidine containing toothpaste with non-ionic surfactant will be able to maintain the antibacterial property and substantivity of chlorhexidine.

Effect of surfactants on the spectrofluorimetric properties of zearalenone

International Nuclear Information System (INIS)

Appell, Michael; Bosma, Wayne B.

2011-01-01

The chemiluminescent properties of the estrogenic mycotoxin zearalenone in the presence of aqueous micellar media were investigated using steady state fluorescence techniques. Micelles of surfactants sodium dodecyl sulfate (SDS), hexadecyltrimethylammonium bromide (CTAB), and non-ionic Triton X-100 enhanced the fluorescence intensity of zearalenone in aqueous solutions. The binding constants have been determined and indicate zearalenone has the highest affinity for Triton X-100, followed by CTAB, and then by SDS. The encapsulation of zearalenone by the micelles studied is spontaneous and exothermic. The selective microenvironments provided by organized micellar systems offer an attractive medium to modulate fluorescence detection of zearalenone. - Highlights: → Surfactants can selectively modulate the fluorescence detection of zearalenone. → Binding studies provide information on the zearalenone-surfactant interactions. → Fluorescence intensity of zearalenone is related to the micelle microenvironment.

Effect of surfactant concentration on the size of one-pot synthesized Si nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Lee, Su Jung; Kim, Tae Woo; Lee, Myong Euy [Dept. of Chemistry and Medical Chemistry, College of Science and Technology, Research and EducationCenter for Advanced Silicon Materials, Yonsei University, Wonju (Korea, Republic of); Cho, Hyeon Mo [University College, Yonsei University, Incheon (Korea, Republic of); Yoon, Sang Woong [Youngchang Chemical Co., LTD, Seongnam (Korea, Republic of); Ryou, Joon Sung [Advanced Technology R and D Center, SKC, Suwon (Korea, Republic of)

2015-07-15

The effect of surfactant concentration on the synthesis of Si nanoparticles (NPs) was studied. Hexyl Si NPs were synthesized using one-pot synthetic methodology with different ratios of SiCl{sub 4}:HexylSiCl{sub 3} (1:1, 1:2, 1:3, 1:6) to observe the effect of surfactant concentration on the size of Si NPs. In Fourier transform infrared spectroscopy analysis, the Si–H stretching band and the characteristic Si–O–Si bands decreased and eventually disappeared with increasing hexyltrichlorosilane concentration. This suggests that the level of oxidation decreased with excess amounts of hexyltrichlorosilane because the surface area of exposed Si NPs without hexyl capping groups was reduced. Results of transmission electron microscopy and particle size analysis showed that the average diameter of hexyl Si NPs increased slightly from low surfactant concentration (SiCl{sub 4}:HexylSiCl{sub 3} = 1:1) to high concentration (1:6). This might be caused due to the relationship between the surfactant concentration effect and the core material part effect of hexyltrichlorosilane. Agglomerated Si NPs were observed and their luminescence bands were not shifted because the Si NPs were capped by alkyl groups to prevent aggregation.

Surfactant effect on functionalized carbon nanotube coated snowman-like particles and their electro-responsive characteristics

Energy Technology Data Exchange (ETDEWEB)

Zhang, Ke; Liu, Ying Dan [Department of Polymer Science and Engineering, Inha University, Incheon 402-751 (Korea, Republic of); Choi, Hyoung Jin, E-mail: hjchoi@inha.ac.kr [Department of Polymer Science and Engineering, Inha University, Incheon 402-751 (Korea, Republic of)

2012-10-15

The core–shell structured snowman-like (SL) microparticles coated by functionalized multi-walled carbon nanotube (MWNT) were prepared in the presence of different surfactants including cationic surfactant-cetyl trimethylammonium bromide (CTAB) and anionic surfactant-sodium lauryl sulfate (SDS). The effect of surfactants on adsorption onto SL particles was characterized by scanning electron microscopy (SEM), thermogravimetric analysis (TGA) and conductivity. The cationic surfactant is found to be more effective than anionic surfactant for helping nanotube adsorbed onto microparticle due to the presence of electrostatic interaction between the functionalized MWNT and the surfactant. Furthermore, the MWNT/SL particles dispersed in silicone oil exhibited a typical fibril structure of the electrorheological characteristics under an applied electric field observed by an optical microscope (OM), in which the state of nanotubes wrapped on the particles strongly affects their electro-responsive characteristics.

Surfactant effect on functionalized carbon nanotube coated snowman-like particles and their electro-responsive characteristics

International Nuclear Information System (INIS)

Zhang, Ke; Liu, Ying Dan; Choi, Hyoung Jin

2012-01-01

The core–shell structured snowman-like (SL) microparticles coated by functionalized multi-walled carbon nanotube (MWNT) were prepared in the presence of different surfactants including cationic surfactant-cetyl trimethylammonium bromide (CTAB) and anionic surfactant-sodium lauryl sulfate (SDS). The effect of surfactants on adsorption onto SL particles was characterized by scanning electron microscopy (SEM), thermogravimetric analysis (TGA) and conductivity. The cationic surfactant is found to be more effective than anionic surfactant for helping nanotube adsorbed onto microparticle due to the presence of electrostatic interaction between the functionalized MWNT and the surfactant. Furthermore, the MWNT/SL particles dispersed in silicone oil exhibited a typical fibril structure of the electrorheological characteristics under an applied electric field observed by an optical microscope (OM), in which the state of nanotubes wrapped on the particles strongly affects their electro-responsive characteristics.

Separation of oil and grease from oil sludge using surfactant

International Nuclear Information System (INIS)

Ainon Abdul Aziz; Syed Hakimi Sakuma Syed Ahmad; Zalina Laili

2005-01-01

The objective of the experiments was to observe the efficiency of the surfactant to remove oil and grease from oil sludges using various surfactant concentration ranging from 10 %, 15 %, 20 % and 30 %. The surfactant solution consists of two mixtures of Aqua 2000 and D Bond. The oil sludge were subjected to heating and surfactant treatment process. Remaining oil and grease concentration were observed on the oil sludges after treatment. Small scale experiments were conducted by heating process, without heating process and heating process with addition of sodium chloride. Surfactant solution was added in each process. Results shows that there is separation of oil and grease from the oil sludges. There were formation of mini emulsions (oil in water). The higher the concentration of surfactant used, the higher the concentrations of mini emulsion formed as observed. Solid remains after the treatment process were found to contain lesser oil concentration with presence of bitumen, sediment, organic and inorganic materials. After a washing process using distilled water, the solid was still black but less oily than before the treatment. There is no separation of oil occurred in aqueous solution for the control experiment. (Author)

Kinetic analysis of anionic surfactant adsorption from aqueous solution onto activated carbon and layered double hydroxide with the zero length column method

NARCIS (Netherlands)

Schouten, N.; van der Ham, Aloysius G.J.; Euverink, G.J.W.; de Haan, A.B.

2009-01-01

Low cost adsorption technology offers high potential to clean-up laundry rinsing water. From an earlier selection of adsorbents, layered double hydroxide (LDH) and granular activated carbon (GAC) proved to be interesting materials for the removal of anionic surfactant, linear alkyl benzene sulfonate

Bioremediation of diesel fuel contaminated soil: effect of non ionic surfactants and selected bacteria addition.

Science.gov (United States)

Collina, Elena; Lasagni, Marina; Pitea, Demetrio; Franzetti, Andrea; Di Gennaro, Patrizia; Bestetti, Giuseppina

2007-09-01

Aim of this work was to evaluate influence of two commercial surfactants and inoculum of selected bacteria on biodegradation of diesel fuel in different systems. Among alkyl polyethossilates (Brij family) and sorbitan derivates (Tween family) a first selection of surfactants was performed by estimation of Koc and Dafnia magna EC50 with molecular descriptor and QSAR model. Further experiments were conducted to evaluate soil sorption, biodegradability and toxicity. In the second part of the research, the effect of Brij 56, Tween 80 and selected bacteria addition on biodegradation of diesel fuel was studied in liquid cultures and in slurry and solid phase systems. The latter experiments were performed with diesel contaminated soil in bench scale slurry phase bioreactor and solid phase columns. Tween 80 addition increased the biodegradation rate of hydrocarbons both in liquid and in slurry phase systems. Regarding the effect of inoculum, no enhancement of biodegradation rate was observed neither in surfactant added nor in experiments without addition. On the contrary, in solid phase experiments, inoculum addition resulted in enhanced biodegradation compared to surfactant addition.

Bioremediation of Diesel Fuel Contaminated Soil: Effect of Non Ionic Surfactants and Selected Bacteria Addition

International Nuclear Information System (INIS)

Collina, E.; Lasagni, M.; Pitea, D.; Franzetti, A.; Di Gennaro, P.; Bestetti, G.

2007-01-01

Aim of this work was to evaluate influence of two commercial surfactants and inoculum of selected bacteria on biodegradation of diesel fuel in different systems. Among alkyl polyethossilates (Brij family) and sorbitan derivates (Tween family) a first selection of surfactants was performed by estimation of Koc and Dafnia magna EC 50 with molecular descriptor and QSAR model. Further experiments were conducted to evaluate soil sorption, biodegradability and toxicity. In the second part of the research, the effect of Brij 56, Tween 80 and selected bacteria addition on biodegradation of diesel fuel was studied in liquid cultures and in slurry and solid phase systems. The latter experiments were performed with diesel contaminated soil in bench scale slurry phase bioreactor and solid phase columns. Tween 80 addition increased the biodegradation rate of hydrocarbons both in liquid and in slurry phase systems. Regarding the effect of inoculum, no enhancement of biodegradation rate was observed neither in surfactant added nor in experiments without addition. On the contrary, in solid phase experiments, inoculum addition resulted in enhanced biodegradation compared to surfactant addition

Spontaneous vesicle phase formation by pseudogemini surfactants in aqueous solutions.

Science.gov (United States)

Sun, Nan; Shi, Lijuan; Lu, Fei; Xie, Shuting; Zheng, Liqiang

2014-08-14

The phase behavior of a kind of pseudogemini surfactant in aqueous solutions, formed by the mixture of sodium dodecyl benzene sulfonate (SDBS) and butane-1,4-bis (methylimidazolium bromide) ([mim-C4-mim]Br2) or butane-1,4-bis(methylpyrrolidinium bromide) ([mpy-C4-mpy]Br2) in a molar ratio of 2 : 1, is reported in the present work. When [mim-C4-mim]Br2 or [mpy-C4-mpy]Br2 is mixed with SDBS in aqueous solutions, one cationic [mim-C4-mim]Br2 or [mpy-C4-mpy]Br2 molecule "bridges" two SDBS molecules by noncovalent interactions (e.g. electrostatic, π-π stacking, and σ-π interactions), behaving like a pseudogemini surfactant. Vesicles can be formed by this kind of pseudogemini surfactant, determined by freeze-fracture transmission electron microscopy (FF-TEM) or cryogenic-transmission electron microscopy (cryo-TEM) and dynamic light scattering (DLS). The mixed system of sodium dodecyl sulfate (SDS) with [mim-C4-mim]Br2 or [mpy-C4-mpy]Br2 was also constructed, and only micelles were observed. We infer that a pseudogemini surfactant is formed under the synergic effect of electrostatic, π-π stacking, and σ-π interactions in the SDBS/[mim-C4-mim]Br2/H2O system, while electrostatic attraction and hydrophobic interactions may provide the directional force for vesicle formation in the SDBS/[mpy-C4-mpy]Br2/H2O system.

Pyrene removal from contaminated soil using electrokinetic process combined with surfactant

Directory of Open Access Journals (Sweden)

Seyed Enayat Hashemi

2015-07-01

Full Text Available Background: Pyrene is one of the stable polycyclic aromatic hydrocarbons that is considered as an important pollutants, because of extensive distribution in the environment and carcinogenic and mutagenic properties. Among the various treatment techniques, electrokinetic method is an environmental- friendly process for organic and mineral pollutants adsorbed to soil with fine pore size the same as clay and low hydraulic conductivity soils. For improving the efficiency of pyrene removal from soil, soulobilization of pyrene from soil could be used by surfactants. Materials and Methods : In this study, clay soil was selected as model because of the specific properties. Combined method using surfactant and electrokinetic was applied for pyrene removal from soil. Experiments were designed using response surface methodology (RSM, and effect of three variables includes surfactant concentration, voltage and surfactant type were evaluated for pyrene removal from contaminated soil. Results: Pyrene removal using anionic surfactants(SDS and nonionic surfactants(TX100 as a solubilizing agents has high removal efficiency. In the optimum condition with 95% confidence coefficient, utilizing mixed surfactants of sodium dodecyl sulfate and triton X-100 with the same volume, induced of 18.54 volt and 6.53 percent surfactant concentration have 94.6% pyrene removal efficiency. Conclusion:: Results of this study shows that electrokinetic process combined with surfactant as solubilizing agent could be applied as an efficient method for treating the pyrene-contaminated soils.

Beyond the detergent effect: a binding site for sodium dodecyl sulfate (SDS) in mammalian apoferritin

Energy Technology Data Exchange (ETDEWEB)

Liu, Renyu, E-mail: renyu.liu@uphs.upenn.edu; Bu, Weiming; Xi, Jin [University of Pennsylvania, Philadelphia, Pennsylvania (United States); Mortazavi, Shirin R. [Drexel University College of Medicine, Philadelphia, Pennsylvania (United States); Cheung-Lau, Jasmina C.; Dmochowski, Ivan J. [University of Pennsylvania, Philadelphia, Pennsylvania (United States); Loll, Patrick J., E-mail: renyu.liu@uphs.upenn.edu [Drexel University College of Medicine, Philadelphia, Pennsylvania (United States); University of Pennsylvania, Philadelphia, Pennsylvania (United States)

2012-05-01

Using X-ray crystallography and isothermal titration calorimetry, we show that sodium dodecyl sulfate (SDS) binds specifically to a pre-formed internal cavity in horse-spleen apoferritin. Although sodium dodecyl sulfate (SDS) is widely used as an anionic detergent, it can also exert specific pharmacological effects that are independent of the surfactant properties of the molecule. However, structural details of how proteins recognize SDS are scarce. Here, it is demonstrated that SDS binds specifically to a naturally occurring four-helix bundle protein: horse apoferritin. The X-ray crystal structure of the apoferritin–SDS complex was determined at a resolution of 1.9 Å and revealed that the SDS binds in an internal cavity that has previously been shown to recognize various general anesthetics. A dissociation constant of 24 ± 9 µM at 293 K was determined by isothermal titration calorimetry. SDS binds in this cavity by bending its alkyl tail into a horseshoe shape; the charged SDS head group lies in the opening of the cavity at the protein surface. This crystal structure provides insights into the protein–SDS interactions that give rise to binding and may prove useful in the design of novel SDS-like ligands for some proteins.

Interactions between selected bile salts and Triton X-100 or sodium lauryl ether sulfate

Directory of Open Access Journals (Sweden)

Ćirin Dejan M

2011-12-01

Full Text Available Abstract Background In order to develop colloidal drug carriers with desired properties, it is important to determine physico-chemical characteristics of these systems. Bile salt mixed micelles are extensively studied as novel drug delivery systems. The objective of the present investigation is to develop and characterize mixed micelles of nonionic (Triton X-100 or anionic (sodium lauryl ether sulfate surfactant having oxyethylene groups in the polar head and following bile salts: cholate, deoxycholate and 7-oxodeoxycholate. Results The micellization behaviour of binary anionic-nonionic and anionic-anionic surfactant mixtures was investigated by conductivity and surface tension measurements. The results of the study have been analyzed using Clint's, Rubingh's, and Motomura's theories for mixed binary systems. The negative values of the interaction parameter indicate synergism between micelle building units. It was noticed that Triton X-100 and sodium lauryl ether sulfate generate the weakest synergistic interactions with sodium deoxycholate, while 7-oxodeoxycholate creates the strongest attractive interaction with investigated co-surfactants. Conclusion It was concluded that increased synergistic interactions can be attributed to the larger number of hydrophilic groups at α side of the bile salts. Additionally, 7-oxo group of 7-oxodeoxycholate enhance attractive interactions with selected co-surfactants more than 7-hydroxyl group of sodium cholate.

Interactions between selected bile salts and Triton X-100 or sodium lauryl ether sulfate.

Science.gov (United States)

Cirin, Dejan M; Poša, Mihalj M; Krstonošić, Veljko S

2011-12-29

In order to develop colloidal drug carriers with desired properties, it is important to determine physico-chemical characteristics of these systems. Bile salt mixed micelles are extensively studied as novel drug delivery systems. The objective of the present investigation is to develop and characterize mixed micelles of nonionic (Triton X-100) or anionic (sodium lauryl ether sulfate) surfactant having oxyethylene groups in the polar head and following bile salts: cholate, deoxycholate and 7-oxodeoxycholate. The micellization behaviour of binary anionic-nonionic and anionic-anionic surfactant mixtures was investigated by conductivity and surface tension measurements. The results of the study have been analyzed using Clint's, Rubingh's, and Motomura's theories for mixed binary systems. The negative values of the interaction parameter indicate synergism between micelle building units. It was noticed that Triton X-100 and sodium lauryl ether sulfate generate the weakest synergistic interactions with sodium deoxycholate, while 7-oxodeoxycholate creates the strongest attractive interaction with investigated co-surfactants. It was concluded that increased synergistic interactions can be attributed to the larger number of hydrophilic groups at α side of the bile salts. Additionally, 7-oxo group of 7-oxodeoxycholate enhance attractive interactions with selected co-surfactants more than 7-hydroxyl group of sodium cholate.

Preparation of ZnS semiconductor nanocrystals using pulsed laser ablation in aqueous surfactant solutions

International Nuclear Information System (INIS)

Choi, S-H; Sasaki, T; Shimizu, Y; Yoon, J-W; Nichols, W T; Sung, Y-E; Koshizaki, N

2007-01-01

Cubic ZnS semiconductor nanocrystals with the size of 2 to 5 nm were prepared by pulsed laser ablation in aqueous surfactant solutions of sodium dodecyl sulfate and cetyltrimethylammonium bromide without any further treatments. The obtained suspensions of the nanocrystals have broad photoluminescence emission from 375 to 600 nm. The abundance and emission intensity of the nanocrystals depend on the concentration of the surfactant in solution

Heterofacial alkylation of alkylenediamines by higher alkyl halides

International Nuclear Information System (INIS)

Semenov, V.A.; Kryshko, G.M.; Sokal'skaya, L.I.; Zhukova, N.G.

1985-01-01

A study of the physiochemical properties of alkylenediamines substituted by lower alkyls, showed that they possess increased complex-forming ability with respect to salts of different metals as titanium, niobium, zirconium, molybdenum, and zinc. To create a simpler method of synthesis of higher tetraaklyalkylalklyenediamines, based on the use of the accessible domestic raw material, the authors investigated the reaction of alkylenediamines with various alkyl halides. It was established that the best reagents can be obtained using alkyl bromides. It is concluded that the procedure of alkylation of alkylenediamines by higher alkyl halides in the presence of water developed permits the production of terraalkylalkylenediamines in one step with good yield and with purity acceptable for use as extraction reagents

Molecular perspective on diazonium adsorption for controllable functionalization of single-walled carbon nanotubes in aqueous surfactant solutions.

Science.gov (United States)

Lin, Shangchao; Hilmer, Andrew J; Mendenhall, Jonathan D; Strano, Michael S; Blankschtein, Daniel

2012-05-16

Functionalization of single-walled carbon nanotubes (SWCNTs) using diazonium salts allows modification of their optical and electronic properties for a variety of applications, ranging from drug-delivery vehicles to molecular sensors. However, control of the functionalization process remains a challenge, requiring molecular-level understanding of the adsorption of diazonium ions onto heterogeneous, charge-mobile SWCNT surfaces, which are typically decorated with surfactants. In this paper, we combine molecular dynamics (MD) simulations, experiments, and equilibrium reaction modeling to understand and model the extent of diazonium functionalization of SWCNTs coated with various surfactants (sodium cholate, sodium dodecyl sulfate, and cetyl trimethylammonium bromide). We show that the free energy of diazonium adsorption, determined using simulations, can be used to rank surfactants in terms of the extent of functionalization attained following their adsorption on the nanotube surface. The difference in binding affinities between linear and rigid surfactants is attributed to the synergistic binding of the diazonium ion to the local "hot/cold spots" formed by the charged surfactant heads. A combined simulation-modeling framework is developed to provide guidance for controlling the various sensitive experimental conditions needed to achieve the desired extent of SWCNT functionalization.

Molecular dynamics simulations of surfactant and nanoparticle self-assembly at liquid-liquid interfaces

Energy Technology Data Exchange (ETDEWEB)

Luo Mingxiang; Dai, Lenore L [Department of Chemical Engineering, Texas Tech University, Lubbock, TX 79409 (United States)

2007-09-19

We have performed molecular dynamics (MD) simulations to investigate self-assembly at water-trichloroethylene (TCE) interfaces with the emphasis on systems containing modified hydrocarbon nanoparticles (1.2 nm in diameter) and sodium dodecyl sulfate (SDS) surfactants. The nanoparticles and surfactants were first distributed randomly in the water phase. The MD simulations have clearly shown the progress of migration and final equilibrium of the SDS molecules at the water-TCE interfaces with the nanoparticles either at or in the vicinity of the interfaces. One unique feature is the 'attachment' of surfactant molecules to the nanoparticle clusters in the water phase followed by the 'detachment' at the water-TCE interfaces. At low concentrations of surfactants, the surfactants and nanoparticles co-equilibrate at the interfaces. However, the surfactants, at high concentrations, competitively dominate the interfaces and deplete nanoparticles away from the interfaces. The interfacial properties, such as interfacial thickness and interfacial tension, are significantly influenced by the presence of the surfactants, but not the nanoparticles. The order of the surfactants at the interfaces increases with increasing surfactant concentration, but is independent of nanoparticle concentration. Finally, the simulation has shown that surfactants can aggregate along the water-TCE interfaces, with and without the presence of nanoparticles.

Interactions between ionic liquid surfactant [C12mim]Br and DNA in dilute brine.

Science.gov (United States)

He, Yunfei; Shang, Yazhuo; Liu, Zhenhai; Shao, Shuang; Liu, Honglai; Hu, Ying

2013-01-01

Interactions between ionic liquid surfactant [C(12)mim]Br and DNA in dilute brine were investigated in terms of various experimental methods and molecular dynamics (MD) simulation. It was shown that the aggregation of [C(12)mim]Br on DNA chains is motivated not only by electrostatic attractions between DNA phosphate groups and [C(12)mim]Br headgroups but also by hydrophobic interactions among [C(12)mim]Br alkyl chains. Isothermal titration calorimetry analysis indicated that the [C(12)mim]Br aggregation in the presence and absence of DNA are both thermodynamically favored driven by enthalpy and entropy. DNA undergoes size transition and conformational change induced by [C(12)mim]Br, and the charges of DNA are neutralized by the added [C(12)mim]Br. Various microstructures were observed such as DNA with loose coil conformation in nature state, necklace-like structures, and compact spherical aggregates. MD simulation showed that the polyelectrolyte collapses upon the addition of oppositely charged surfactants and the aggregation of surfactants around the polyelectrolyte was reaffirmed. The simulation predicted the gradual neutralization of the negatively charged polyelectrolyte by the surfactant, consistent with the experimental results. Copyright © 2012 Elsevier B.V. All rights reserved.

Non toxic biodegradable cationic gemini surfactants as novel corrosion inhibitor for mild steel in hydrochloric acid medium and synergistic effect of sodium salicylate: Experimental and theoretical approach

Energy Technology Data Exchange (ETDEWEB)

Mobin, Mohammad, E-mail: drmmobin@hotmail.com; Aslam, Ruby; Aslam, Jeenat

2017-04-15

Two biodegradable, non toxic cationic gemini surfactants having ester linkage in the spacer namely, C{sub m}H{sub 2m+1}(CH{sub 3}){sub 2}N{sup +}(CH{sub 2}COOCH{sub 2}){sub 2}N{sup +}(CH{sub 3}){sub 2}C{sub m}H{sub 2m+1}.2Cl{sup -} (m-E2-m, m = 12, 14), were synthesized and characterized using elemental analysis, FT-IR and {sup 1}H-NMR. The corrosion inhibition performance of synthesized compounds separately and in combination with sodium salicylate (SS), along with the nature and stability of inhibitive film, for mild steel (MS) in 1 M HCl solution at 30–60 °C was evaluated using weight loss, potentiodynamic polarization, EIS, UV–visible spectroscopy, FTIR, SEM/EDAX, TGA and quantum chemical calculations. Results of the studies confirm m-E2-m as effective corrosion inhibitor for MS in HCl; the inhibition effect being synergistically strengthened in presence of SS. The synthesized compounds act as mixed type inhibitor and adsorb on MS surface in accordance with Langmuir adsorption isotherm. Experimentally measured inhibition efficiencies are correlated with the molecular parameters obtained using PM6 semi-empirical method. Empirical results are in good agreement with the theoretical predictions. - Graphical abstract: (a) Optimized geometry of studied inhibitors by PM6 method with (b) HOMO and (c) LUMO orbital occupation. - Highlights: • Environment friendly gemini surfactants were studied as corrosion inhibitor for MS. • Studied compounds act as good inhibitor for MS corrosion in 1 M HCl at 30–60 °C. • η of inhibitors is synergistically increased in presence of sodium salicylate. • The synthesized cationic gemini surfactants act as mixed-type inhibitor. • Experimentally obtained results are in good agreement with theoretical results.

Standard molar enthalpies of formation of sodium alkoxides

International Nuclear Information System (INIS)

Chandran, K.; Srinivasan, T.G.; Gopalan, A.; Ganesan, V.

2007-01-01

The molar enthalpies of solution of sodium in methanol, ethanol, and n-propanol and of sodium alkoxides in their corresponding alcohols were measured at T=298.15K using an isoperibol solution calorimeter. From these results and other auxiliary data, the standard molar enthalpies of formation, Δ f H m o (RONa,cr) of sodium methoxide, sodium ethoxide, and sodium n-propoxide were calculated and found to be {(-366.21+/-1.38) (-413.39+/-1.45), and (-441.57+/-1.18)}kJ.mol -1 , respectively. A linear correlation has been found between Δ f H m o (RONa)andΔ f H m o (ROH) for R=n-alkyl, enabling the prediction of data for other sodium alkoxides

Influence of Surfactants and Fluoride against Enamel Erosion.

Science.gov (United States)

Zanatta, Rayssa Ferreira; Ávila, Daniele Mara da Silva; Miyamoto, Karen Mayumi; Torres, Carlos Rocha Gomes; Borges, Alessandra Bühler

2018-06-06

This study investigated the effect of surfactants associated with sodium fluoride (NaF) on enamel erosion prevention, using an erosion-remineralization in vitro model. Sodium lauryl sulfate (SLS), polysorbate 20 (P20), and cocoamidopropyl betaine (CAPB) were tested, at concentrations of 1.0 and 1.5%, and associated or not with NaF (275 ppm). The control groups were distilled water and the NaF solution. Bovine enamel samples (n = 12) were prepared and submitted to a 5-day cycling model: acid challenge (0.3% citric acid, pH 2.6, 4×/day), human saliva (2 h, 4×/day), and the treatment solutions (2 min, 2×/day). The protective potential of the agents against initial erosion was assessed by microhardness and the surface loss by profilometry. Enamel surface wettability was determined by goniometry, protein adsorption was measured by spectroscopy (FTIR), and the KOH-soluble fluoride was quantified. Goniometry showed that SLS and CAPB increased enamel wettability. No differences were found among the surfactants regarding protein adsorption. Microhardness showed that SLS reduced NaF protection. P20 (1 and 1.5%) and CAPB 1.5% presented a protective effect, but lower than the NaF solution. Profilometry showed that CAPB protected enamel, but no agent associated with NaF promoted a higher protection than the NaF solution alone. KOH-soluble fluoride analysis showed that all surfactants reduced the fluoride adsorption on the enamel surface. Therefore, the surfactants tested (except for P20) changed the enamel surface energy. The SLS decreased the protective potential of NaF on initial erosion, but no tested agent interfered with the protective effect of NaF on enamel erosive wear. © 2018 S. Karger AG, Basel.

Evaluation of bacterial surfactant toxicity towards petroleum degrading microorganisms.

Science.gov (United States)

Lima, Tânia M S; Procópio, Lorena C; Brandão, Felipe D; Leão, Bruna A; Tótola, Marcos R; Borges, Arnaldo C

2011-02-01

The acute toxicity of bacterial surfactants LBBMA111A, LBBMA155, LBBMA168, LBBMA191 and LBBMA201 and the synthetic surfactant sodium dodecyl sulfate (SDS) on the bioluminescent bacterium Vibrio fischeri was evaluated by measuring the reduction of light emission (EC(20)) by this microorganism when exposed to different surfactant concentrations. Moreover, the toxic effects of different concentrations of biological and synthetic surfactants on the growth of pure cultures of isolates Acinetobacter baumannii LBBMA04, Acinetobacter junni LBBMA36, Pseudomonas sp. LBBMA101B and Acinetobacter baumanni LBBMAES11 were evaluated in mineral medium supplemented with glucose. The EC(20) values obtained confirmed that the biosurfactants have a significantly lower toxicity to V. fischeri than the SDS. After 30 min of exposure, bacterial luminescence was almost completely inhibited by SDS at a concentration of 4710 mg L(-1). Growth reduction of pure bacterial cultures caused by the addition of biosurfactants to the growth medium was lower than that caused by SDS. Copyright © 2010 Elsevier Ltd. All rights reserved.

Synthesis, surface properties and antimicrobial activity of some germanium nonionic surfactants.

Science.gov (United States)

Zaki, Mohamed F; Tawfik, Salah M

2014-01-01

Esterification reaction between different fatty acid namely; lauric, stearic, oleic and linoleic acids and polyethylene glycol-400 were performed. The produced polyethylene glycol ester were reacted with p-amine benzoic acid followed by condensation reaction with germanium dioxide in presence of sodium carbonate to form desired germinate surfactants. The chemical structures of the synthesized surfactants were determined using different spectra tools. The surface parameter including: the critical micelle concentration (CMC), effectiveness (π(cmc)), efficiency (Pc20), maximum surface excess (Γ(max)) and minimum surface area (A(min)), were calculated from the surface tension measurements. The synthesized surfactants showed higher surface activity. The thermodynamic parameters showed that adsorption and micellization processes are spontaneous. It is clear that the synthesized nonionic surfactants showed their tendency towards adsorption at the interfaces and also micellization in the bulk of their solutions. The synthesized surfactants were tested against different strain of bacteria using inhibition zone diameters. The synthesized surfactants showed good antimicrobial activities against the tested microorganisms including Gram positive, Gram negative as well as fungi. The promising inhibition efficiency of these compounds against the sulfate reducing bacteria facilitates them to be applicable as new categories of sulfate reducing bacteria biocides.

Surfactants enhance recovery of poorly soluble drugs during microdialysis sampling

DEFF Research Database (Denmark)

Koplin, Sebastian; Kumpugdee-Vollrath, Mont; Bauer-Brandl, Annette

2017-01-01

Aim of this project was to investigate the applicability of a recently developed in vitro microdialysis-sampling approach in connection with a dissolution-/permeation (D/P) system, especially the impact of surfactants within the perfusion fluid. The D/P-system is based on side-by-side chambers...... drug-dissolution (-release) and drug permeation. Furthermore, it should allow quantification of the unbound (free) drug concentration. In the first step, it was assessed, if the addition of the anionic surfactant sodium dodecyl sulphate (SDS) to the perfusate of the microdialysis system affects...... celecoxib, i.e. the fraction of drug, which is not associated with taurocholate surfactant micelles. In buffer, the measured concentrations matched the overall CXB concentrations. By the use of SDS-containing perfusates microdialysis sampling enabled reliable quantification of minute amounts of free CXB...

The effects of anionic and cationic surfactants on the ion flotation of Cd2+

International Nuclear Information System (INIS)

Kobayashi, Koichi

1975-01-01

The ion flotation of Cd 2+ ions has been investigated from the surface chemical point of view in comparison with the case of Cu 2+ ions reported previously. The effects of the change in the pH, the anionic and cationic surfactants, and bentonite on the flotation rate have also been studied. Sodium α-sulfolaurate proved to be one of the best surfactants among the anionic surfactants used for removing Cd 2+ ions, showing as high as a 97% removal. About 97% of the Cd 2+ ions could be floated in the region of pH 11.3 when a cationic surfactant was used with bentonite, regardless of the exact surfactant used. The addition of bentonite reduced the foam formation and liquid hold-up, resulting in effective bubble flotation. This behavior was as a whole similar to that of Cu 2+ ions. However, in all the flotation systems tested, the flotation rate increased sharply at about pH 8, and the flotation rate vs. pH curve for Cd 2+ shifted towards a more alkaline region than that for Cu 2+ , because of the stronger basic nature of the former. Also, the flotation rate of Cd 2+ ions for the Cd 2+ -anionic surfactant systems attained a steady value after about 7 min, longer than the 2-min gas flow required in the case of Cu 2+ ion flotation. The adjustment of the pH using ammonia gave a lower rate of flotation than in the case of flotation using sodium hydroxide. (auth.)

Adsorption of diclofenac onto organoclays: Effects of surfactant and environmental (pH and temperature) conditions

OpenAIRE

De Oliveira , Tiago; Guégan , Régis; Thiebault , Thomas; Le Milbeau , Claude; Muller , Fabrice; Teixeira , Vinicius; Giovanela , Marcelo; Boussafir , Mohammed

2017-01-01

Accepted Manuscript; International audience; Among pharmaceutical products (PPs) recalcitrant to water treatments, diclofenac shows a high toxicity and remains at high concentration in natural aquatic environments. The aim of this study concerns the understanding of the adsorption mechanism of this anionic PP onto two organoclays prepared with two long-alkyl chains cationic surfactants showing different chemical nature for various experimental pH and temperature conditions. The experimental d...

Acidic Pretreatment of Wheat Straw in Decanol for the Production of Surfactant, Lignin and Glucose

Directory of Open Access Journals (Sweden)

Boris Estrine

2011-12-01

Full Text Available Wheat straw is an abundant residue of agriculture which is increasingly being considered as feedstock for the production of fuels, energy and chemicals. The acidic decanol-based pre-treatment of wheat straw has been investigated in this work. Wheat straw hemicellulose has been efficiently converted during a single step operation into decyl pentoside surfactants and the remaining material has been preserved keeping all its promises as potential feedstock for fuels or value added platform chemicals such as hydroxymethylfurfural (HMF. The enzymatic digestibility of the cellulose contained in the straw residue has been evaluated and the lignin prepared from the material characterized. Wheat-based surfactants thus obtained have exhibited superior surface properties compared to fossil-based polyethoxylates decyl alcohol or alkyl oligoglucosides, some of which are largely used surfactants. In view of the growing importance of renewable resource-based molecules in the chemical industry, this approach may open a new avenue for the conversion of wheat straw into various chemicals.

Solid-phase extraction sorbent consisting of alkyltrimethylammonium surfactants immobilized onto strong cation-exchange polystyrene resin.

Science.gov (United States)

Reid, Kendra R; Kennedy, Lonnie J; Crick, Eric W; Conte, Eric D

2002-10-25

Presented is a solid-phase extraction sorbent material composed of cationic alkyltrimethylammonium surfactants attached to a strong cation-exchange resin via ion-exchange. The original hydrophilic cation-exchange resin is made hydrophobic by covering the surface with alkyl chains from the hydrophobic portion of the surfactant. The sorbent material now has a better ability to extract hydrophobic molecules from aqueous samples. The entire stationary phase (alkyltrimethylammonium surfactant) is removed along with the analyte during the elution step. The elution step requires a mild elution solvent consisting of 0.25 M Mg2+ in a 50% 2-propanol solution. The main advantage of using a removable stationary phase is that traditionally utilized toxic elution solvents such as methylene chloride, which are necessary to efficiently release strongly hydrophobic species from SPE stationary phases, may now be avoided. Also, the final extract is directly compatible with reversed-phase liquid chromatography. The performance of this procedure is presented using pyrene as a test molecule.

Sodium Hypochlorite and Sodium Bromide Individualized and Stabilized Carbon Nanotubes in Water

KAUST Repository

Xu, Xuezhu

2017-09-20

Aggregation is a major problem for hydrophobic carbon nanomaterials such as carbon nanotubes (CNTs) in water because it reduces the effective particle concentration, prevents particles from entering the medium, and leads to unstable electronic device performances when a colloidal solution is used. Molecular ligands such as surfactants can help the particles to disperse, but they tend to degrade the electrical properties of CNTs. Therefore, self-dispersed particles without the need for surfactant are highly desirable. We report here, for the first time to our knowledge, that CNT particles with negatively charged hydrophobic/water interfaces can easily self-disperse themselves in water via pretreating the nanotubes with a salt solution with a low concentration of sodium hypochlorite (NaClO) and sodium bromide (NaBr). The obtained aqueous CNT suspensions exhibit stable and superior colloidal performances. A series of pH titration experiments confirmed the presence and role of the electrical double layers on the surface of the salted carbon nanotubes and of functional groups and provided an in-depth understanding of the phenomenon.

Sodium Hypochlorite and Sodium Bromide Individualized and Stabilized Carbon Nanotubes in Water

KAUST Repository

Xu, Xuezhu; Zhou, Jian; Colombo, Veronica; Xin, Yangyang; Tao, Ran; Lubineau, Gilles

2017-01-01

Aggregation is a major problem for hydrophobic carbon nanomaterials such as carbon nanotubes (CNTs) in water because it reduces the effective particle concentration, prevents particles from entering the medium, and leads to unstable electronic device performances when a colloidal solution is used. Molecular ligands such as surfactants can help the particles to disperse, but they tend to degrade the electrical properties of CNTs. Therefore, self-dispersed particles without the need for surfactant are highly desirable. We report here, for the first time to our knowledge, that CNT particles with negatively charged hydrophobic/water interfaces can easily self-disperse themselves in water via pretreating the nanotubes with a salt solution with a low concentration of sodium hypochlorite (NaClO) and sodium bromide (NaBr). The obtained aqueous CNT suspensions exhibit stable and superior colloidal performances. A series of pH titration experiments confirmed the presence and role of the electrical double layers on the surface of the salted carbon nanotubes and of functional groups and provided an in-depth understanding of the phenomenon.

Surfactant mediated slurry formulations for Ge CMP applications

KAUST Repository

Basim, G. Bahar

2013-01-01

In this study, slurry formulations in the presence of self-assembled surfactant structures were investigated for Ge/SiO2 CMP applications in the absence and presence of oxidizers. Both anionic (sodium dodecyl sulfate-SDS) and cationic (cetyl trimethyl ammonium bromide-C12TAB) micelles were used in the slurry formulations as a function of pH and oxidizer concentration. CMP performances of Ge and SiO2 wafers were evaluated in terms of material removal rates, selectivity and surface quality. The material removal rate responses were also assessed through AFM wear rate tests to obtain a faster response for preliminary analyses. The surfactant adsorption characteristics were studied through surface wettability responses of the Ge and SiO2 wafers through contact angle measurements. It was observed that the self-assembled surfactant structures can help obtain selectivity on the silica/germanium system at low concentrations of the oxidizer in the slurry. © 2013 Materials Research Society.

Morphological control of seedlessly-synthesized gold nanorods using binary surfactants

Science.gov (United States)

Roach, Lucien; Ye, Sunjie; Moorcroft, Samuel C. T.; Critchley, Kevin; Coletta, P. Louise; Evans, Stephen D.

2018-04-01

High purity gold nanorods (AuNRs) with tunable morphology have been synthesized through a binary-surfactant seedless method, which enables the formation of monocrystalline AuNRs with diameters between 7 and 35 nm. The protocol has high shape yield and monodispersity, demonstrating good reproducibility and scalability allowing synthesis of batches 0.5 l in volume. Morphological control has been achieved through the adjustment of the molar concentrations of cetyltrimethylammonium bromide and sodium oleate in the growth solution, providing fine tuning of the optical scattering and absorbance properties of the AuNRs across the visible and NIR spectrum. Sodium oleate was found to provide greatest control over the aspect ratio (and hence optical properties) with concentration changes between 10 and 23 mM leading to variation in the aspect ratio between 2.8 and 4.8. Changes in the geometry of the end-caps were also observed as a result of manipulating the two surfactant concentrations.

Preparation of a Fluorocarbon Polymerizable Surfactant and Its Application in Emulsion Polymerization of Fluorine-Containing Acrylate

Directory of Open Access Journals (Sweden)

Meng Zhao

2017-11-01

Full Text Available A novel polymerizable fluorocarbon surfactant, perfluoro (4–methyl–3, 6–dioxaoct–7–ene sodium sulfonate (PSVNa, was synthesized and characterized. The fluorocarbon surfactant PSVNa and its mixture PSVNa/SDS were used as emulsifiers during the emulsion polymerization of DFHMA/MMA. The investigation of polymerization kinetics, particle size, and stability of the emulsions revealed that PSVNa has excellent emulsifying properties. The NMR spectrum of the copolymer and the detection of residual PSVNa show that more than 95% of the fluorocarbon surfactants have been linked to the polymer chains by radical polymerization, which will greatly reduce the environmental pollution caused by fluorinated surfactants.

Synthesis and Surface Activity of Cationic Amino Acid-Based Surfactants in Aqueous Solution.

Science.gov (United States)

Greber, Katarzyna E

2017-01-01

I studied the possibility of using amino acid-based surfactants as emulsifiers at the same time as preservatives. Fourteen lipopeptides were synthesized employing a solid phase peptide synthesis procedure. All compounds were designed to be positively charged from +1 to +4 and acylated with fatty acid chain-palmitic and miristic. The surface activity of the obtained lipopeptides was tested using a semi-automatic tensiometer to calculate parameters describing the behavior of lipopeptides in the air/water interface. Such parameters as CMC, surface tension at the CMC point ( σ CMC ), effectiveness ( π CMC ), and efficiency (pC20) were measured. Emulsifying properties of all lipopeptides were also examined. The studies reveal that the surface active properties of synthesized compounds strongly depend on the length of alkyl chains as well as on the composition of amino acid polar heads. The critical micelle concentration decreases with increasing alkyl chain length of lipopeptides with the same polar head. The effectiveness and efficiency decrease when the number of amino acids in the polar head increases. All lipopeptides established a very weak emulsification power and created unstable water/Miglyol 812 and water/paraffin oil emulsions. Results suggest that lipopeptides cannot be used as emulsifiers; nonetheless, it is possible to use them as auxiliary surfactants with disinfectant properties in combination with more potent emulsifiers.

Binding affinities of cationic dyes in the presence of activated charcoal and anionic surfactant in the premicellar region

Science.gov (United States)

Ali, Farman; Ibrahim, Muhammad; Khan, Fawad; Bibi, Iram; Shah, Syed W. H.

2018-03-01

Binding preferences of cationic dyes malachite green and methylene blue in a mixed charcoal-sodium dodecyl sulfate system have been investigated using UV-visible absorption spectroscopy. The dye adsorption shows surfactant-dependent patterns, indicating diverse modes of interactions. At low surfactant concentration, a direct binding to charcoal is preferred. Comparatively greater quantities of surfactant lead to attachment of dye-surfactant complex to charcoal through hydrophobic interactions. A simple model was employed for determination of equilibrium constant K eq and concentration of dye-surfactant ion pair N DS for both dyes. The values of binding parameters revealed that malachite green was directly adsorbed onto charcoal, whereas methylene blue was bound through surfactant monomers. The model is valid for low surfactant concentrations in the premicellar region. These findings have significance for material and environmental sciences.

pH-Sensitive self-propelled motion of oil droplets in the presence of cationic surfactants containing hydrolyzable ester linkages.

Science.gov (United States)

Banno, Taisuke; Kuroha, Rie; Toyota, Taro

2012-01-17

Self-propelled oil droplets in a nonequilibrium system have drawn much attention as both a primitive type of inanimate chemical machinery and a dynamic model of the origin of life. Here, to create the pH-sensitive self-propelled motion of oil droplets, we synthesized cationic surfactants containing hydrolyzable ester linkages. We found that n-heptyloxybenzaldehyde oil droplets were self-propelled in the presence of ester-containing cationic surfactant. In basic solution prepared with sodium hydroxide, oil droplets moved as molecular aggregates formed on their surface. Moreover, the self-propelled motion in the presence of the hydrolyzable cationic surfactant lasted longer than that in the presence of nonhydrolyzable cationic surfactant. This is probably due to the production of a fatty acid by the hydrolysis of the ester-containing cationic surfactant and the subsequent neutralization of the fatty acid with sodium hydroxide. A complex surfactant was formed in the aqueous solution because of the cation and anion combination. Because such complex formation can induce both a decrease in the interfacial tension of the oil droplet and self-assembly with n-heptyloxybenzaldehyde and lauric acid in the aqueous dispersion, the prolonged movement of the oil droplet may be explained by the increase in heterogeneity of the interfacial tension of the oil droplet triggered by the hydrolysis of the ester-containing surfactant. © 2011 American Chemical Society

Performance improvement of ionic surfactant flooding in carbonate rock samples by use of nanoparticles

Directory of Open Access Journals (Sweden)

Mohammad Ali Ahmadi

2016-07-01

Full Text Available Abstract Various surfactants have been used in upstream petroleum processes like chemical flooding. Ultimately, the performance of these surfactants depends on their ability to reduce the interfacial tension between oil and water. The surfactant concentration in the aqueous solution decreases owing to the loss of the surfactant on the rock surface in the injection process. The main objective of this paper is to inhibit the surfactant loss by means of adding nanoparticles. Sodium dodecyl sulfate and silica nanoparticles were used as ionic surfactant and nanoparticles in our experiments, respectively. AEROSIL® 816 and AEROSIL® 200 are hydrophobic and hydrophilic nanoparticles. To determine the adsorption loss of the surfactant onto rock samples, a conductivity approach was used. Real carbonate rock samples were used as the solid phase in adsorption experiments. It should be noted that the rock samples were water wet. This paper describes how equilibrium adsorption was investigated by examining adsorption behavior in a system of carbonate sample (solid phase and surfactant solution (aqueous phase. The initial surfactant and nanoparticle concentrations were 500–5000 and 500–2000 ppm, respectively. The rate of surfactant losses was extremely dependent on the concentration of the surfactant in the system, and the adsorption of the surfactant decreased with an increase in the nanoparticle concentration. Also, the hydrophilic nanoparticles are more effective than the hydrophobic nanoparticles.

One-pot synthesis of 4′-alkyl-4-cyanobiaryls on the basis of the terephthalonitrile dianion and neutral aromatic nitrile cross-coupling

Directory of Open Access Journals (Sweden)

Roman Yu. Peshkov

2016-07-01

Full Text Available A convenient one-pot approach to alkylcyanobiaryls is described. The method is based on biaryl cross-coupling between the sodium salt of the terephthalonitrile dianion and a neutral aromatic nitrile in liquid ammonia, and successive alkylation of the long-lived anionic intermediate with alkyl bromides. The reaction is compatible with benzonitriles that contain methyl, methoxy and phenyl groups, fluorine atoms, and a 1-cyanonaphthalene residue. The variety of ω-substituted alkyl bromides, including an extra bromine atom, a double bond, cyano and ester groups, as well as a 1,3-dioxane fragment are suitable as alkylation reagents.

Methotrexate intercalated layered double hydroxides with the mediation of surfactants: Mechanism exploration and bioassay study

Energy Technology Data Exchange (ETDEWEB)

Dai, Chao-Fan; Tian, De-Ying; Li, Shu-Ping, E-mail: lishuping@njnu.edu.cn; Li, Xiao-Dong

2015-12-01

Methotrexatum intercalated layered double hydroxides (MTX/LDHs) hybrids were synthesized by the co-precipitation method and three kinds of nonionic surfactants with different hydrocarbon chain lengths were used. The resulting hybrids were then characterized by X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy and transmission electron microscopy (TEM). XRD and FTIR investigations manifest the successful intercalation of MTX anions into the interlayer of LDHs. TEM graphs indicate that the morphology of the hybrids changes with the variation of the chain length of the surfactants, i.e., the particles synthesized using polyethylene glycol (PEG-7) present regular disc morphology with good monodispersity, while samples with the mediation of alkyl polyglycoside (APG-14) are heavily aggregated and samples with the addition of polyvinylpyrrolidone (PVP-10) exhibit irregular branches. Furthermore, the release and bioassay experiments show that monodisperse MTX/LDHs present good controlled-release and are more efficient in the suppression of the tumor cells. - Highlights: • Surfactants could be used to modify the dispersing state of MTX/LDHs hybrids. • Surfactants have great effect on the morphology of MTX/LDHs hybrids. • MTX/LDHs with good monodisperse degree are more efficient in the suppression of the tumor cells.

Toluidine blue-sodium lauryl ether sulfate complexes : Influence of ethylene oxide length

NARCIS (Netherlands)

Vleugels, L.F.W.; Féat, A.; Voets, I.K.; Tuinier, R.

2017-01-01

Sodium Lauryl Ether Sulfates (SLES) are an increasingly important and versatile type of surfactants. The complexation between ortho-Toluidine blue (TBO) and a homologous series of SLES, including Sodium Lauryl Sulfate (SDS) without Ethylene Oxide (EO), has been investigated using visible

Preparation, physicochemical characterisation and magnetic properties of Cu-Al layered double hydroxides with CO 32- and anionic surfactants with different alkyl chains in the interlayer

Science.gov (United States)

Trujillano, Raquel; Holgado, María Jesús; Pigazo, Fernando; Rives, Vicente

2006-03-01

Layered double hydroxides with the hydrotalcite-like structure, containing Cu(II) and Al(III) in the layers, and different alkyl sulphonates in the interlayer, have been prepared and characterised by powder X-ray diffraction, FT-IR spectroscopy, differential thermal analysis and thermogravimetric analysis. Their magnetic properties have been also studied. Except for the sample containing octadecanesulphonate in the interlayer, for which an excess of sulphonate exists, pure crystalline phases have been obtained in the other cases. Upon heating, combustion of the organic chain takes place at lower temperature than for the corresponding sodium salts. A two-dimensional antiferromagnetic behaviour is observed at 200 K in all samples containing intercalated sulphonate. The χT value is lower for the samples containing interlayer sulphonates (with layer-layer distances in the 21-31 Å range), than for a carbonate-containing analogue (basal spacing 7.51 Å).

Influence of MWCNT/surfactant dispersions on the mechanical properties of Portland cement pastes

Science.gov (United States)

Rodríguez, B.; Quintero, J. H.; Arias, Y. P.; Mendoza-Reales, O. A.; Ochoa-Botero, J. C.; Toledo-Filho, R. D.

2017-12-01

This work studies the reinforcing effect of Multi Walled Carbon Nanotubes (MWCNT) on cement pastes. A 0.35% solid concentration of MWCNT in powder was dispersed in deionized water with sodium dodecyl sulfate (cationic surfactant), cetylpyridinium chloride (anionic surfactant) and triton X-100 (amphoteric surfactant) using an ultrasonic tip processor. Three concentrations of each surfactant (1mM, 10mM and 100mM) were tested, and all samples were sonicated until an adequate dispersion degree was obtained. Cement pastes with additions of carbon nanotubes of 0.15% by mass of cement were produced in two steps; first the dispersions of MWCNT were combined with the mixing water using an ultrasonic tip processor to guarantee homogeneity, and then cement was added and mixed until a homogeneous paste was obtained. Direct tensile strength, apparent density and open porosity of the pastes were measured after 7 days of curing. It was found that the MWCNT/surfactants dispersions decrease the mechanical properties of the cement based matrix due to an increased porosity caused by the presence of surfactants.

Electrostatic Screening and Charge Correlation Effects in Micellization of Ionic Surfactants

KAUST Repository

Jusufi, Arben

2009-05-07

We have used atomistic simulations to study the role of electrostatic screening and charge correlation effects in self-assembly processes of ionic surfactants into micelles. Specifically, we employed grand canonical Monte Carlo simulations to investigate the critical micelle concentration (cmc), aggregation number, and micellar shape in the presence of explicit sodium chloride (NaCl). The two systems investigated are cationic dodecyltrimethylammonium chloride (DTAC) and anionic sodium dodecyl sulfate (SDS) surfactants. Our explicit-salt results, obtained from a previously developed potential model with no further adjustment of its parameters, are in good agreement with experimental data for structural and thermodynamic micellar properties. We illustrate the importance of ion correlation effects by comparing these results with a Yukawa-type surfactant model that incorporates electrostatic screening implicitly. While the effect of salt on the cmc is well-reproduced even with the implicit Yukawa model, the aggregate size predictions deviate significantly from experimental observations at low salt concentrations. We attribute this discrepancy to the neglect of ion correlations in the implicit-salt model. At higher salt concentrations, we find reasonable agreement of the Yukawa model with experimental data. The crossover from low to high salt concentrations is reached when the electrostatic screening length becomes comparable to the headgroup size. © 2009 American Chemical Society.

Anaerobic digestion of amine-oxide-based surfactants: biodegradation kinetics and inhibitory effects.

Science.gov (United States)

Ríos, Francisco; Lechuga, Manuela; Fernández-Arteaga, Alejandro; Jurado, Encarnación; Fernández-Serrano, Mercedes

2017-08-01

Recently, anaerobic degradation has become a prevalent alternative for the treatment of wastewater and activated sludge. Consequently, the anaerobic biodegradability of recalcitrant compounds such as some surfactants require a thorough study to avoid their presence in the environment. In this work, the anaerobic biodegradation of amine-oxide-based surfactants, which are toxic to several organisms, was studied by measuring of the biogas production in digested sludge. Three amine-oxide-based surfactants with structural differences in their hydrophobic alkyl chain were tested: Lauramine oxide (AO-R 12 ), Myristamine oxide (AO-R 14 ) and Cocamidopropylamine oxide (AO-cocoamido). Results show that AO-R 12 and AO-R 14 inhibit biogas production, inhibition percentages were around 90%. AO-cocoamido did not cause inhibition and it was biodegraded until reaching a percentage of 60.8%. Otherwise, we fitted the production of biogas to two kinetic models, to a pseudo first-order model and to a logistic model. Production of biogas during the anaerobic biodegradation of AO-cocoamido was pretty good adjusted to the logistics model. Kinetic parameters were also determined. This modelling is useful to predict their behaviour in wastewater treatment plants and under anaerobic conditions in the environment.

Chichibabin-type direct alkylation of pyridyl alcohols with alkyl lithium reagents.

Science.gov (United States)

Jeffrey, Jenna L; Sarpong, Richmond

2012-11-02

Direct C(6) alkylation of pyridyl alcohols can be achieved following an initial deprotonation of the hydroxy group. This transformation, which is believed to occur by a Chichibabin-type alkylation, avoids lateral deprotonation prior to pyridine ring alkylation and gives increased regioselectivity for C(6) over C(4) alkylation.

Evaluation of a common commercial surfactant in a water recycle system

International Nuclear Information System (INIS)

Rector, T.; Jackson, A.; Rainwater, K.; Pickering, S.

2002-01-01

The fate of a common commercial surfactant was investigated in the biological reactors of a water recycle system. A NO 2 - reducing packed-bed bioreactor was employed to evaluate degradation of surfactant present in a typical greywater stream. The research was conducted to determine if an alternative commercial surfactant could be used in a biological water recycle system proposed for space travel in place of the current surfactant. The commercial soap used in the research was Pert Plus for Kids (PPK), which contains sodium laureth sulfate (SLES) as the active surfactant. Experiments included a combination of microcosm studies as well as a continuous-flow packed-bed bioreactor. The hydraulic retention time of the packed-bed bioreactor was varied through changes in flow rate to yield different steady-state values for NO 2 -N, TOC, and COD. Steady-state values will allow the determination of the bacterial kinetic parameters. Initial results suggest that the commercial surfactant may be difficult to treat in the time frame of typical biological systems. NO 2 - reduction was favorable in the packed-bed reactor, but TOC removal rates did not correspond to the NO 2 - removal. It is theorized that, due to its high K oc value (1200), SLES has an affinity to absorb to the media contained in the bed, which in turn allows for adsorption of the surfactant. Future research will include development of an isotherm model to characterize the adsorption rates and correlate them to surfactant removal. (author)

Cytotoxicity of Poly(Alkyl Cyanoacrylate Nanoparticles

Directory of Open Access Journals (Sweden)

Einar Sulheim

2017-11-01

Full Text Available Although nanotoxicology has become a large research field, assessment of cytotoxicity is often reduced to analysis of one cell line only. Cytotoxicity of nanoparticles is complex and should, preferentially, be evaluated in several cell lines with different methods and on multiple nanoparticle batches. Here we report the toxicity of poly(alkyl cyanoacrylate nanoparticles in 12 different cell lines after synthesizing and analyzing 19 different nanoparticle batches and report that large variations were obtained when using different cell lines or various toxicity assays. Surprisingly, we found that nanoparticles with intermediate degradation rates were less toxic than particles that were degraded faster or more slowly in a cell-free system. The toxicity did not vary significantly with either the three different combinations of polyethylene glycol surfactants or with particle size (range 100–200 nm. No acute pro- or anti-inflammatory activity on cells in whole blood was observed.

Mass spectrometry compatible surfactant for optimized in-gel protein digestion.

Science.gov (United States)

Saveliev, Sergei V; Woodroofe, Carolyn C; Sabat, Grzegorz; Adams, Christopher M; Klaubert, Dieter; Wood, Keith; Urh, Marjeta

2013-01-15

Identification of proteins resolved by SDS-PAGE depends on robust in-gel protein digestion and efficient peptide extraction, requirements that are often difficult to achieve. A lengthy and laborious procedure is an additional challenge of protein identification in gel. We show here that with the use of the mass spectrometry compatible surfactant sodium 3-((1-(furan-2-yl)undecyloxy)carbonylamino)propane-1-sulfonate, the challenges of in-gel protein digestion are effectively addressed. Peptide quantitation based on stable isotope labeling showed that the surfactant induced 1.5-2 fold increase in peptide recovery. Consequently, protein sequence coverage was increased by 20-30%, on average, and the number of identified proteins saw a substantial boost. The surfactant also accelerated the digestion process. Maximal in-gel digestion was achieved in as little as one hour, depending on incubation temperature, and peptides were readily recovered from gel eliminating the need for postdigestion extraction. This study shows that the surfactant provides an efficient means of improving protein identification in gel and streamlining the in-gel digestion procedure requiring no extra handling steps or special equipment.

Synthesis of hydroxyapatite particles in catanionic mixed surfactants template

International Nuclear Information System (INIS)

Tari, Nesa Esmaeilian; Kashani Motlagh, Mohammad M.; Sohrabi, Beheshteh

2011-01-01

Highlights: ►The mixture of cetyltrimethyl ammonium bromide (CTAB) and sodium dodecyl sulfate (SDS) with different ratio were used as the template for synthesizing HAP particles. ► The overall morphology of the obtained powders at anionic-rich region (SDS:CTAB, 99:1) solution is rod like with high regularity. ► In the presence of cationic rich region (SDS:CTAB, 1:99) the resulted particles was sheet like. ► The resulted HAP nano particles in the presence of SDS were rod like but their morphology was less oriented than anionic-rich region. - Abstract: Different morphologies of nano hydroxyapatite particles, Ca 10 (PO 4 ) 6 (OH) 2 (HAP) are prepared by precipitation method using CaCl 2 and H 3 PO 4 (water phase) and the mixture of cationic surfactant cetyltrimethyl ammonium bromide (CTAB) and anionic one sodium dodecyl sulfate (SDS) as template. The mixture of these surfactants in two regions of cationic-rich and anionic-rich form the various aggregations as template. The results show that by changing the ratio of cationic to anionic surfactant in the mixture the morphology of the nano HAP can be controlled. The nano structure of products is studied by the means of X-ray diffraction (XRD), Fourier transmission infrared spectrometer (FT-IR) and scanning electron microscopy (SEM). With this system we could synthesize nano particles of hydroxyapatite with high crystallinity and least agglomeration.

Synthesis of hydroxyapatite particles in catanionic mixed surfactants template

Energy Technology Data Exchange (ETDEWEB)

Tari, Nesa Esmaeilian [Department of Chemistry, Iran University of Science and Technology, Resalat Square, Hengam Street, Tehran (Iran, Islamic Republic of); Kashani Motlagh, Mohammad M., E-mail: M.Kashani@iust.ac.ir [Department of Chemistry, Iran University of Science and Technology, Resalat Square, Hengam Street, Tehran (Iran, Islamic Republic of); Sohrabi, Beheshteh [Department of Chemistry, Iran University of Science and Technology, Resalat Square, Hengam Street, Tehran (Iran, Islamic Republic of)

2011-12-15

Highlights: Black-Right-Pointing-Pointer The mixture of cetyltrimethyl ammonium bromide (CTAB) and sodium dodecyl sulfate (SDS) with different ratio were used as the template for synthesizing HAP particles. Black-Right-Pointing-Pointer The overall morphology of the obtained powders at anionic-rich region (SDS:CTAB, 99:1) solution is rod like with high regularity. Black-Right-Pointing-Pointer In the presence of cationic rich region (SDS:CTAB, 1:99) the resulted particles was sheet like. Black-Right-Pointing-Pointer The resulted HAP nano particles in the presence of SDS were rod like but their morphology was less oriented than anionic-rich region. - Abstract: Different morphologies of nano hydroxyapatite particles, Ca{sub 10}(PO{sub 4}){sub 6}(OH){sub 2} (HAP) are prepared by precipitation method using CaCl{sub 2} and H{sub 3}PO{sub 4} (water phase) and the mixture of cationic surfactant cetyltrimethyl ammonium bromide (CTAB) and anionic one sodium dodecyl sulfate (SDS) as template. The mixture of these surfactants in two regions of cationic-rich and anionic-rich form the various aggregations as template. The results show that by changing the ratio of cationic to anionic surfactant in the mixture the morphology of the nano HAP can be controlled. The nano structure of products is studied by the means of X-ray diffraction (XRD), Fourier transmission infrared spectrometer (FT-IR) and scanning electron microscopy (SEM). With this system we could synthesize nano particles of hydroxyapatite with high crystallinity and least agglomeration.

Petroleum Contaminated Soil Treatment Using Surfactant and Hydrogen Peroxide

Directory of Open Access Journals (Sweden)

Ilza Lobo

2010-12-01

Full Text Available The process of washing soil with surfactants, sodium lauryl ether sulphate (LESS and sodium lauryl sulphate (SDS was combined with chemical oxidation using hydrogen peroxide, with a view to in situ remediation of clay soil contaminated with hydrocarbons oil. The evaluation of the efficiency of the procedure was the removal of polyaromatic hydrocarbons and the comparison of physical and chemical characteristics of contaminated soil and uncontaminated from the same region. The combination of these two techniques, soil washing and application of an oxidizing agent, presented as a process of effective remediation for soils contaminated with petroleum products in subtropical regions.

Influence of anionic surfactant on the process of electro-Fenton decolorized methyl orange.

Science.gov (United States)

Ren, B X

2010-01-01

The electro-Fenton process has been shown to be very successful to remove dyes from water. However, the influence of other constituents in dyeing industry wastewater, such as Sodium Dodecyl Sulfate (SDS) surfactants, has not been investigated. In this study, the effect of SDS surfactant on the kinetics of Methyl Orange degradation undergoing Electro-Fenton process was investigated. Results show that Methyl Orange degradation rate decreased as SDS concentration (below Critical Micelle Concentration, CMC) increased, which was attributed to the consumption of hydroxyl radicals (( )OH) by surfactants. The kinetics modeling indicates the reaction was the first-order reaction to Methyl Orange even SDS existing. The pseudo first-order rate constants decreased as SDS concentration increased.

Effect of anionic surfactants on the process of Fenton degradation of methyl orange.

Science.gov (United States)

Yang, C W; Wang, D

2009-01-01

Fenton process has been shown to be very successful to remove dyes from water. However, the influence of other constituents in dyeing industry wastewater, such as Sodium Dodecyl Sulphate (SDS) surfactants, has not been investigated. In this study, the effect of SDS surfactant on the kinetics of Methyl Orange degradation undergoing Fenton process was investigated. Results show that Methyl Orange degradation rate decreased as SDS concentration increased, which was attributed to the consumption of hydroxyl radicals (OH) by surfactants and the formation of Methyl Orange-SDS complex. No evidence was found that the Methyl Orange degradation pathway was affected by the presence of SDS. The kinetics modelling indicates the reaction was the first-order reaction to Methyl Orange.

Composition driven monolayer to bilayer transformation in a surfactant intercalated Mg-Al layered double hydroxide.

Science.gov (United States)

Naik, Vikrant V; Chalasani, Rajesh; Vasudevan, S

2011-03-15

The structure and organization of dodecyl sulfate (DDS) surfactant chains intercalated in an Mg-Al layered double hydroxide (LDH), Mg(1-x)Alx(OH)2, with differing Al/Mg ratios has been investigated. The Mg-Al LDHs can be prepared over a range of compositions with x varying from 0.167 to 0.37 and therefore provides a simple system to study how the organization of the alkyl chains of the intercalated DDS anions change with packing density; the Al/Mg ratio or x providing a convenient handle to do so. Powder X-ray diffraction measurements showed that at high packing densities (x ≥ 0.3) the alkyl chains of the intercalated dodecyl sulfate ions are anchored on opposing LDH sheets and arranged as bilayers with an interlayer spacing of ∼27 Å. At lower packing densities (x flat in the galleries with an interlayer spacing of ∼8 Å. For the in between compositions, 0.2 ≤ x organization of the chains and the interlayer spacing. The simulations are able to reproduce the composition driven monolayer to bilayer transformation in the arrangement of the intercalated surfactant chains and in addition provide insights into the factors that decide the arrangement of the surfactant chains in the two situations. In the bilayer arrangement, it is the dispersive van der Waals interactions between chains in opposing layers of the anchored bilayer that is responsible for the cohesive energy of the solid whereas at lower packing densities, where a monolayer arrangement is favored, Coulomb interactions between the positively charged Mg-Al LDH sheets and the negatively charged headgroup of the DDS anion dominate.

Improved surfactants formulation for remediation of oil sludge recovery

International Nuclear Information System (INIS)

Syed Hakimi Sakuma Syed Ahmad; Shahidan Radiman

2000-01-01

Surfactant enhanced remediation based on mobilisation of the residual NAPLs (oil sludge) which is radioactive depends on the tendency of the surfactants to lower interfacial tension. Mobilisation has greater potential than solubilisation to increase the rate of remediation. Optimised surfactants formulation was determined with concentration of Aqua 2000 and D Bond of 1% wt respectively, sodium chloride concentration of 2 gmL -1 and addition of 3% wt butanol as cosolvent. The formulation was of benefit not only able to decrease further the interfacial tension of aqueous solution containing oil emulsion, but also to make possible to be more mobile and destruction of mixed liquid crystals that formed. Formation of liquid crystals can hinders significantly recovery efficiency of aqueous solution containing oil emulsion in field remediation work. In a 100 litres soil column experiment conducted containing oil emulsion in field sludge soil and using the surfactants formulation for flushing, miniemulsion formed sizes maintained at average size between 125 nm and 280 nm before and after remediation. Total oil and grease concentration removed from the soil were significant due to the decreased in oil emulsion sizes, increase mobility and solubility. (Author)

Ammonium Laurate Surfactant for Cleaner Deposition of Carbon Nanotubes

Energy Technology Data Exchange (ETDEWEB)

Nilsson, Hanna M. [Department of Material Science and Engineering and ‡Department of Chemistry and Biochemistry, University of Maryland, College Park, Maryland 20742, United States; Meany, Brendan [Department of Material Science and Engineering and ‡Department of Chemistry and Biochemistry, University of Maryland, College Park, Maryland 20742, United States; Ticey, Jeremy [Department of Material Science and Engineering and ‡Department of Chemistry and Biochemistry, University of Maryland, College Park, Maryland 20742, United States; Sun, Chuan-Fu [Department of Material Science and Engineering and ‡Department of Chemistry and Biochemistry, University of Maryland, College Park, Maryland 20742, United States; Wang, YuHuang [Department of Material Science and Engineering and ‡Department of Chemistry and Biochemistry, University of Maryland, College Park, Maryland 20742, United States; Cumings, John [Department of Material Science and Engineering and ‡Department of Chemistry and Biochemistry, University of Maryland, College Park, Maryland 20742, United States

2015-06-15

Experiments probing the properties of individual carbon nanotubes (CNTs) and those measuring bulk composites show vastly different results. One major issue limiting the results is that the procedures required to separate and test CNTs introduce contamination that changes the properties of the CNT. These contamination residues often come from the resist used in lithographic processing and the surfactant used to suspend and deposit the CNTs, commonly sodium dodecyl sulfate (SDS). Here we present ammonium laurate (AL), a surfactant that has previously not been used for this application, which differs from SDS only by substitution of ionic constituents but shows vastly cleaner depositions. In addition, we show that compared to SDS, AL-suspended CNTs have greater shelf stability and more selective dispersion. These results are verified using transmission electron microscopy, atomic force microscopy, ζ-potential measurements, and Raman and absorption optical spectroscopy. This surfactant is simple to prepare, and the nanotube solutions require minimal sonication and centrifugation in order to outperform SDS.

Atomistic simulations of surfactant adsorption kinetics at interfaces

Science.gov (United States)

Iskrenova, Eugeniya; Patnaik, Soumya

2014-03-01

Heat transfer control and enhancement is an important and challenging problem in a variety of industrial and technological applications including aircraft thermal management. The role of additives in nucleate boiling and phase change in general has long been recognized and studied experimentally and modeled theoretically but in-depth description and atomistic understanding of the multiscale processes involved are still needed for better prediction and control of the heat transfer efficiency. Surfactant additives have been experimentally observed to either enhance or inhibit the boiling heat transfer depending on the surfactant concentration and chemistry and, on a molecular level, their addition leads to dynamic surface tension and changes in interfacial and transfer properties, thus contributing to the complexity of the problem. We present our atomistic modeling study of the interfacial adsorption kinetics of aqueous surfactant (sodium dodecyl sulfate) systems at a range of concentrations at room and boiling temperatures. Classical molecular dynamics and Umbrella Sampling simulations were used to study the surfactant transport properties and estimate the adsorption and desorption rates at liquid-vacuum and liquid-solid interfaces. The authors gratefully acknowledge funding from AFOSR Thermal Science Program and the Air Force Research Laboratory DoD Supercomputing Resource Center for computing time and resources.

Pengaruh Penambahan Sodium Lauril Sulfat (Sls) Sebagai Surfaktan Terhadap Sifat Fisik Dan Uji Disolusi Tablet Ketoprofen

OpenAIRE

Pratama, Adithya Wahyu; Siswanto, Agus; Suparman, Suparman

2012-01-01

Ketoprofen (acid 2-(3-benzoilfenil) propanoat) was derivated of propionat acid which has analgesic, antipyretic, and anti-inflammatory with poor solubillity in water. This research allowed to increase the dissolution rate of ketoprofen tablets and effect on the physical characteristic by adding sodium lauril sulfat as surfactant. Sodium lauryl sulfat is a surfactant that can be used to improve wetting and dissolution rate. This study was done with make four formula of ketoprofen tablets by d...

Self-assembly, foaming, and emulsifying properties of sodium alkyl carboxylate/guanidine hydrochloride aqueous mixtures.

Science.gov (United States)

Fameau, Anne-Laure; Houinsou-Houssou, Bérénice; Ventureira, Jorge Luis; Navailles, Laurence; Nallet, Frédéric; Novales, Bruno; Douliez, Jean-Paul

2011-04-19

Unsaturated fatty acids may be extracted from various agricultural resources and are widely used as soaps in the industry. However, there also exist a large variety of saturated and hydroxy fatty acids in nature, but their metal salts crystallize at room temperature in water, hampering their use in biological and chemical studies or for industrial applications. Addition of guanidine hydrochloride (GuHCl) to sodium salt of myristic acid has been shown to prevent its crystallization in water, forming stable flat bilayers at room temperature. Herein, we extend this finding to two other saturated fatty acids (palmitic and stearic acids) and two hydroxyl fatty acids (juniperic and 12 hydroxy stearic acids) and study more deeply (by using small angle neutron scattering) the supramolecular assemblies formed in both saturated and hydroxyl fatty acid systems. In addition, we take the advantage that crystallization no longer occurs at room temperature in the presence of GuHCl to study the foaming and emulsifying properties of those fatty acid dispersions. Briefly, our results show that all fatty acids, even juniperic acid, which is a bola lipid, are arranged in a bilayer structure that may be interdigitated. Depending on the nature of the fatty acid, the systems exhibit good foamability and foam stability (except for juniperic acid), and emulsion stability was good. Those findings should be of interest for using saturated long chain (and hydroxyl) fatty acids as surfactants for detergency or even materials chemistry. © 2011 American Chemical Society

76 FR 6335 - Sodium and Potassium Salts of N-alkyl (C8

Science.gov (United States)

2011-02-04

... dietary risk due to a series of compounded conservatisms. First, assuming that the level of residue for an... because surfactants are generally used at levels far below this percentage. Second, the conservatism of... commodity. Finally, a third compounding conservatism is EPA's assumption that all foods contain the inert...

Comparative tests on the biodegradation of secondary alkane sulphonate, using 14C-labelled preparations

International Nuclear Information System (INIS)

Loetzsch, K.; Neufahrt, A.; Taeuber, G.

1979-01-01

The biodegradability of 14 C-labelled and unlabelled secondary alkane sulphonates (SAS) and an unlabelled alkyl benzene sulphonate as well as ar ring-labelled sodium-4-(dodecyl-(4'))-benzene sulphonate (LAS) was tested over a period of 12 days with slight germ introduction under aerobic conditions (Hach apparatus). In the 'one-pot method' (simultaneous determination of MBAS, DOC and BSB) with the unlabelled A-surfactants, it was shown that biodegradation of both substances started at different speeds and is almost finished after 15 days in the case of SAS and after 30 days in the case of LAS. The tests with radioactively labelled secondary alkane sulphonate showed that the greater part of the surfactant carbon is quickly degraded to CO 2 . It therefore behaves like uniformly labelled stearate or like a stearyl alcohol ethoxylate uniformly labelled in the alkyl chain. Both were included in the tests as reference substances. The dissimilation processes of the ring-labelled linear alkyl benzene sulphonate are delayed. Here, CO 2 formation started only after a few days. (orig.) [de

Discourse of the form and concentration of surfactants to ensure the sustainability foam-emulsive products

Directory of Open Access Journals (Sweden)

O. Kotlyar

2015-05-01

Full Text Available Introduction. Development of dry mixes for making spumy and emulsion products are topical, because nowadays there is a tendency to minimize the time spent on the process of cooking, which is achieved by the use of semi finished products high degree of readiness. Materials and methods. Foaming ability was determined by the method of multiplicity of the foam, the stability of unstable foam-by the half-life method of foam, highly resistant foam - as a ratio of the height of the column of foam after exposure for 24 hours. Results. Was determined the influence of sunflower oil on the foaming ability and half-life foam of systems «sodium caseinate-oil». It was found that getting systems with high index of foaming capacity and foam stability in the presence of oil in the system is impossible without the use of low molecular weight surfactants. Substantiated recommendations regarding the feasibility of using two surfactants in systems «sodium caseinate-surfactants-oil», which provide the necessary kinship surfaces air, fat and water phases. it has been found that the use of 2,5...3,5% mono-and diglycerides of fatty acid sand Lecithin’s 0.15...0.25% in the content of sodium caseinate about 0.5% allows to receive the stable foam-emulsive systems containing sunflower oil 7...8% and foaming ability about 640±1%. Conclusions. It is established that for ensuring high indicators foaming capacity and stability of foam-emulsive systems required the use of low-molecular surfactants. The research results, is recommended to use when developing technology of foam-emulsive products. Introduction

Discourse of the form and concentration of surfactants to ensure the sustainability foam-emulsive products

Directory of Open Access Journals (Sweden)

Oleg

2015-05-01

Full Text Available Introduction. Development of dry mixes for making spumy and emulsion products are topical, because nowadays there is a tendency to minimize the time spent on the process of cooking, which is achieved by the use of semi finished products high degree of readiness. Materials and methods. Foaming ability was determined by the method of multiplicity of the foam, the stability of unstable foam-by the half-life method of foam, highly resistant foam - as a ratio of the height of the column of foam after exposure for 24 hours. Results. Was determined the influence of sunflower oil on the foaming ability and half-life foam of systems «sodium caseinate-oil». It was found that getting systems with high index of foaming capacity and foam stability in the presence of oil in the system is impossible without the use of low molecular weight surfactants. Substantiated recommendations regarding the feasibility of using two surfactants in systems «sodium caseinate-surfactants-oil», which provide the necessary kinship surfaces air, fat and water phases. it has been found that the use of 2,5...3,5% mono-and diglycerides of fatty acid sand Lecithin’s 0.15...0.25% in the content of sodium caseinate about 0.5% allows to receive the stable foam-emulsive systems containing sunflower oil 7...8% and foaming ability about 640±1%. Conclusions. It is established that for ensuring high indicators foaming capacity and stability of foam-emulsive systems required the use of low-molecular surfactants. The research results, is recommended to use when developing technology of foam-emulsive products.

NMR studies of electrophoretic mobility in surfactant systems

International Nuclear Information System (INIS)

Conveney, F.M.; Strange, J.H.; Smith, A.L.; Smith, E.G.

1989-01-01

An experimental technique is described in which the flow of electrically charged micelles is measured in the presence of an applied electric field using an NMR technique. The method is used to determine the electrophoretic mobility at ambient temperature of a 5% aqueous solution of sodium dodecyl sulphate and is shown to provide a new technique for the study of electrophoresis in surfactant solutions. (author). 8 refs.; 4 figs

Study of complex thermosensitive amphiphilic polyoxazolines and their interaction with ionic surfactants. Are hydrophobic, thermosensitive, and hydrophilic moieties equally important?

Czech Academy of Sciences Publication Activity Database

Bogomolova, Anna; Filippov, Sergey K.; Starovoytova, Larisa; Angelov, Borislav; Konarev, P.; Sedláček, Ondřej; Hrubý, Martin; Štěpánek, Petr

2014-01-01

Roč. 118, č. 18 (2014), s. 4940-4950 ISSN 1520-6106 R&D Projects: GA ČR GAP205/11/1657; GA MPO FR-TI4/625 Grant - others:AV ČR(CZ) M200501201 Program:M Institutional support: RVO:61389013 Keywords : poly(2-alkyl-2-oxazoline) * thermosensitivity * ionic surfactant Subject RIV: CD - Macromolecular Chemistry Impact factor: 3.302, year: 2014

Biomimetic oligosaccharide and peptide surfactant polymers designed for cardiovascular biomaterials

Science.gov (United States)

Ruegsegger, Mark Andrew

A common problem associated with cardiovascular devices is surface induced thrombosis initiated by the rapid, non-specific adsorption of plasma proteins onto the biomaterial surface. Control of the initial protein adsorption is crucial to achieve the desired longevity of the implanted biomaterial. The cell membrane glycocalyx acts as a non-thrombogenic interface through passive (dense oligosaccharide structures) and active (ligand/receptor interactions) mechanisms. This thesis is designed to investigate biomimicry of the cell glycocalyx to minimize non-specific protein adsorption and promote specific ligand/receptor interactions. Biomimetic macromolecules were designed through the molecular-scale engineering of polymer surfactants, utilizing a poly(vinyl amine) (PVAm) backbone to which hydrophilic (dextran, maltose, peptide) and hydrophobic alkyl (hexanoyl or hexanal) chains are simultaneously attached. The structure was controlled through the molar feed ratio of hydrophobic-to-hydrophilic groups, which also provided control of the solution and surface-active properties. To mimic passive properties, a series of oligomaltose surfactants were synthesized with increasing saccharide length (n = 2, 7, 15 where n is number of glucose units) to investigate the effect of coating height on protein adsorption. The surfactants were characterized by infra red (IR) and nuclear magnetic resonance (NMR) spectroscopies for structural properties and atomic force microscopy (AFM) and contact angle goniometry for surface activity. Protein adsorption under dynamic flow (5 dyn/cm2) was reduced by 85%--95% over the bare hydrophobic substrate; platelet adhesion dropped by ˜80% compared to glass. Peptide ligands were incorporated into the oligosaccharide surfactant to promote functional activity of the passive coating. The surfactants were synthesized to contain 0%, 25%, 50%, 75%, and 100% peptide ligand density and were stable on hydrophobic surfaces. The peptide surface density was

Maintaining Supersaturation of Nimodipine by PVP with or without the Presence of Sodium Lauryl Sulfate and Sodium Taurocholate.

Science.gov (United States)

Pui, Yipshu; Chen, Yuejie; Chen, Huijun; Wang, Shan; Liu, Chengyu; Tonnis, Wouter; Chen, Linc; Serno, Peter; Bracht, Stefan; Qian, Feng

2018-05-30

Amorphous solid dispersion (ASD) is one of the most versatile supersaturating drug delivery systems to improve the dissolution rate and oral bioavailability of poorly water-soluble drugs. PVP based ASD formulation of nimodipine (NMD) has been marketed and effectively used in clinic for nearly 30 years, yet the mechanism by which PVP maintains the supersaturation and subsequently improves the bioavailability of NMD was rarely investigated. In this research, we first studied the molecular interactions between NMD and PVP by solution NMR, using CDCl 3 as the solvent, and the drug-polymer Flory-Huggins interaction parameter. No strong specific interaction between PVP and NMD was detected in the nonaqueous state. However, we observed that aqueous supersaturation of NMD could be significantly maintained by PVP, presumably due to the hydrophobic interactions between the hydrophobic moieties of PVP and NMD in aqueous medium. This hypothesis was supported by dynamic light scattering (DLS) and supersaturation experiments in the presence of different surfactants. DLS revealed the formation of NMD/PVP aggregates when NMD was supersaturated, suggesting the formation of hydrophobic interactions between the drug and polymer. The addition of surfactants, sodium lauryl sulfate (SLS) or sodium taurocholate (NaTC), into PVP maintained that NMD supersaturation demonstrated different effects: SLS could only improve NMD supersaturation with concentration above its critical aggregation concentration (CAC) value while not with lower concentration. Nevertheless, NaTC could prolong NMD supersaturation independent of concentration, with lower concentration outperformed higher concentration. We attribute these observations to PVP-surfactant interactions and the formation of PVP/surfactant complexes. In summary, despite the lack of specific interactions in the nonaqueous state, NMD aqueous supersaturation in the presence of PVP was attained by hydrophobic interactions between the hydrophobic

Characterization of surfactant/hydrotalcite-like clay/glassy carbon modified electrodes: Oxidation of phenol

International Nuclear Information System (INIS)

Hernandez, Maria; Fernandez, Lenys; Borras, Carlos; Mostany, Jorge; Carrero, Hermes

2007-01-01

The characteristics of hydrotalcite (HT)-like clay films containing ionic and nonionic surfactants and their ability to oxidize phenol have been examined. The HT clay (Co/Al-NO 3 ) was synthesized by coprecipitation techniques and then modified with surfactants such as sodium dodecylbenzenesulfonate (SDBS), octylphenoxypolyethoxyethanol (TX100) or cetylpyridinium bromide (CPB). X-ray diffraction analysis revealed that the interlayer basal spacing varied depending on the type of surfactant retained by the HT. The presence of SDBS and CPB expanded the HT interlayer, which in the presence of TX100 did not show an appreciable change. Phenol oxidation is favored at surfactant-HT-GC modified electrodes, after a preconcentration time, compared to phenol oxidation at HT-GC or GC electrodes. Surfactant-HT-GC modified electrodes display good stability in continuous electrochemical phenol oxidation. At pH values between 6 and 10.8, both SDBS-HT-GC and TX100-HT-GC modified electrodes seem to be promising electrodes for the detection of phenol in water; while the CPB-HT-GC modified electrode should be affected by the inorganic anions

Synthesis and evaluation of sequence-specific DNA alkylating agents: effect of alkylation subunits.

Science.gov (United States)

Shimizu, Tatsuhiko; Sasaki, Shunta; Minoshima, Masafumi; Shinohara, Ken-ichi; Bando, Toshikazu; Sugiyama, Hiroshi

2006-01-01

We have demonstrated that hairpin pyrrole (Py)- imidazole (Im) polyamide-CBI conjugates selectively alkylate predetermined sequences. In this study, we investigated the effect of alkylation subunits, for example conjugates 1-4 with three types of DNA alkylating units, and Py-Im polyamides with indole linker. Conjugate 3 and 4 selectively alkylated the predetermined sequences as described previously, while conjugates 1 and 2 alkylate at mismatched sites.

Effect of surfactants on the properties of hydrotalcites prepared by the reverse micelle method

Energy Technology Data Exchange (ETDEWEB)

Holgado, Patricia H., E-mail: h.holgado@usal.es; Holgado, María J., E-mail: holgado@usal.es; San Román, María S., E-mail: sanroman@usal.es; Rives, Vicente, E-mail: vrives@usal.es

2015-02-01

Layered double hydroxides with the hydrotalcite-type structure have been prepared by the reverse micelles method. The layer cations were Ni{sup 2+} and Fe{sup 3+} in all cases and the interlayer anion was carbonate. We have studied the effect of the surfactant used (with linear chains of different lengths, or cyclic) and the effect of the pH on the properties of the solids formed. These have been characterized by element chemical analysis, powder X-ray diffraction, thermogravimetric analysis, temperature-programmed reduction, FT-IR and Vis–UV spectroscopies and scanning electron microscopy. It has been found that the samples prepared at pH 9 are more crystalline than those prepared at pH 11 and their crystallite sizes are always larger than for samples prepared by the conventional precipitation method. Surfactants with cyclic organic chains lead to a larger crystallite size, probably because the water pool vesicle where the crystallite grows is larger due to sterical hindrance of the organic chains. - Graphical abstract: Layered double hydroxides with the hydrotalcite-type structure with Ni{sup 2+} and Fe{sup 3+} cations in the layers have been prepared by the reverse micelles method. Different surfactants were used at different pH synthesis. Samples prepared at pH 9 are higher crystalline than those prepared at pH 11. Surfactants with cyclic organic chains lead to a larger crystallite size. - Highlights: • Hydrotalcites were prepared by the micelles reverse method. • Straight alkyl or cyclic chain surfactants were used. • All hydrotalcites are well crystallized at pH = 9 and 11. • The crystallite size depends on the linear/cyclic nature of the surfactant chain.

Effect of surfactants on the properties of hydrotalcites prepared by the reverse micelle method

International Nuclear Information System (INIS)

Holgado, Patricia H.; Holgado, María J.; San Román, María S.; Rives, Vicente

2015-01-01

Layered double hydroxides with the hydrotalcite-type structure have been prepared by the reverse micelles method. The layer cations were Ni 2+ and Fe 3+ in all cases and the interlayer anion was carbonate. We have studied the effect of the surfactant used (with linear chains of different lengths, or cyclic) and the effect of the pH on the properties of the solids formed. These have been characterized by element chemical analysis, powder X-ray diffraction, thermogravimetric analysis, temperature-programmed reduction, FT-IR and Vis–UV spectroscopies and scanning electron microscopy. It has been found that the samples prepared at pH 9 are more crystalline than those prepared at pH 11 and their crystallite sizes are always larger than for samples prepared by the conventional precipitation method. Surfactants with cyclic organic chains lead to a larger crystallite size, probably because the water pool vesicle where the crystallite grows is larger due to sterical hindrance of the organic chains. - Graphical abstract: Layered double hydroxides with the hydrotalcite-type structure with Ni 2+ and Fe 3+ cations in the layers have been prepared by the reverse micelles method. Different surfactants were used at different pH synthesis. Samples prepared at pH 9 are higher crystalline than those prepared at pH 11. Surfactants with cyclic organic chains lead to a larger crystallite size. - Highlights: • Hydrotalcites were prepared by the micelles reverse method. • Straight alkyl or cyclic chain surfactants were used. • All hydrotalcites are well crystallized at pH = 9 and 11. • The crystallite size depends on the linear/cyclic nature of the surfactant chain

Effect of surfactant on kinetics of thinning of capillary bridges

Science.gov (United States)

Nowak, Emilia; Kovalchuk, Nina; Simmons, Mark

2015-11-01

Kinetics of thinning of capillary bridges is of great scientific and industrial interest being of vital importance for example in various emulsification and microfluidic processes. It is well known that the rate of bridge thinning is proportional to the interfacial tension. Therefore it is expected that the process should slow down by addition of surfactant. The kinetics of capillary bridges in the presence of surfactant was studied by the dripping of liquid from a capillary tip under conditions of nearly zero flow rate (We personal care products. The viscosity, surfactant activity and adsorption kinetics have been controlled by addition of glycerol and sodium chloride. The study has shown that the kinetics of capillary bridges are determined by dynamic surface tension rather than by its equilibrium value. In particular, the kinetics of the bridge thinning for the 0.1 g L-1 aqueous SLES solution is practically the same as that of pure water despite twice lower equilibrium surface tension. EPSRC Programme Grant, MEMPHIS, EP/K0039761/1.

HPLC/ESI-quadrupole ion trap mass spectrometry for characterization and direct quantification of amphoteric and nonionic surfactants in aqueous samples

Science.gov (United States)

Levine, Lanfang H.; Garland, Jay L.; Johnson, Jodie V.

2002-01-01

An amphoteric (cocamidopropylbetaine, CAPB) and a nonionic (alcohol polyethoxylate, AE) surfactant were characterized by electrospray ionization quadrupole ion trap mass spectrometry (ESI-MS) as to their homologue distribution and ionization/fragmentation chemistry. Quantitative methods involving reversed-phase gradient HPLC and (+)ESI-MSn were developed to directly determine these surfactants in hydroponic plant growth medium that received simulated graywater. The predominant homologues, 12 C alkyl CAPB and 9 EO AE, were monitored to represent the total amount of the respective surfactants. The methods demonstrated dynamic linear ranges of 0.5-250 ng (r2 > 0.996) for CAPB and 8-560 ng (r2 > 0.998) for AE homologue mixture, corresponding to minimum quantification limits of 25 ppb CAPB and 0.4 ppm AE with 20-microL injections. This translated into an even lower limit for individual components due to the polydispersive nature of the surfactants. The procedure was successfully employed for the assessment of CAPB and AE biodegradation in a hydroponic plant growth system used as a graywater bioreactor.

Effect of Presence and Concentration of Plasticizers, Vegetable Oils, and Surfactants on the Properties of Sodium-Alginate-Based Edible Coatings

Science.gov (United States)

Schott, Michael; Müller, Kajetan

2018-01-01

Achieving high quality of a coated food product is mostly dependent on the characteristics of the food material to be coated, the properties of the components in the coating solution, and the obtained coating material. In the present study, usability and effectiveness of various components as well as their concentrations were assessed to produce an effective coating material. For this purpose, different concentrations of gelling agent (sodium alginate 0–3.5%, w/w), plasticizers (glycerol and sorbitol (0–20%, w/w), surfactants (tween 40, tween 80, span 60, span 80, lecithin (0–5%, w/w), and vegetable oils (sunflower oil, olive oil, rapeseed oil (0–5%, w/w) were used to prepare edible coating solutions. Formulations were built gradually, and characteristics of coatings were evaluated by analyzing surface tension values and its polar and dispersive components, emulsion droplet size, and optical appearance in microscopic scale. The results obtained showed that 1.25% sodium alginate, 2% glycerol, 0.2% sunflower oil, 1% span 80, and 0.2% tween 40 or tween 80 can be used in formulation to obtain an effective coating for hydrophobic food surfaces. Three formulations were designed, and their stability (emulsion droplet size, optical characteristics, and creaming index) and wettability tests on strawberry showed that they could be successfully used in coating applications. PMID:29509669

Effect of Presence and Concentration of Plasticizers, Vegetable Oils, and Surfactants on the Properties of Sodium-Alginate-Based Edible Coatings

Directory of Open Access Journals (Sweden)

Tugce Senturk Parreidt

2018-03-01

Full Text Available Achieving high quality of a coated food product is mostly dependent on the characteristics of the food material to be coated, the properties of the components in the coating solution, and the obtained coating material. In the present study, usability and effectiveness of various components as well as their concentrations were assessed to produce an effective coating material. For this purpose, different concentrations of gelling agent (sodium alginate 0–3.5%, w/w, plasticizers (glycerol and sorbitol (0–20%, w/w, surfactants (tween 40, tween 80, span 60, span 80, lecithin (0–5%, w/w, and vegetable oils (sunflower oil, olive oil, rapeseed oil (0–5%, w/w were used to prepare edible coating solutions. Formulations were built gradually, and characteristics of coatings were evaluated by analyzing surface tension values and its polar and dispersive components, emulsion droplet size, and optical appearance in microscopic scale. The results obtained showed that 1.25% sodium alginate, 2% glycerol, 0.2% sunflower oil, 1% span 80, and 0.2% tween 40 or tween 80 can be used in formulation to obtain an effective coating for hydrophobic food surfaces. Three formulations were designed, and their stability (emulsion droplet size, optical characteristics, and creaming index and wettability tests on strawberry showed that they could be successfully used in coating applications.

Competition between a lamellar and a microemulsion phase in an ionic surfactant system

NARCIS (Netherlands)

Kegel, W.K.; Lekkerkerker, H.N.W.

1993-01-01

An experimental study of a microemulsion system consisting of equal volumes of brine (water plus salt) and oil (cyclohexane), sodium dodecyl sulfate (SDS) as surfactant, and a mixture of hexanol and pentanol as cosurfactant is presented. Increasing the hexanol fraction in the cosurfactant mixture

No Ameliorating Effect of Surfactant Protein D on DSS-Induced Colitis in Mice

DEFF Research Database (Denmark)

Nexøe, Anders Bathum; Pilecki, Bartosz; Husby, Steffen

Inflammatory bowel diseases (IBD) are disorders associated to a pathological immune response. Surfactant protein D (SP-D) is part of the innate host defense and has known anti-inflammatory effects. We hypothesize that SP-D dampens dextran sodium sulfate (DSS)-induced colitis by reducing innate...

Critical role of surfactants in the formation of digestively-ripened, ultra-small (r<2 nm) copper oxide quantum dots

Science.gov (United States)

Talluri, Bhusankar; Prasad, Edamana; Thomas, Tiju

2018-04-01

Synthesis of ultra-small (r photovoltaics to sensing. Digestive ripening (DR), a method for preparing uniformly-sized particles is critically influenced by nature and concentrations of the starting materials, solvent, and surfactant. To better understand the DR process there is a need to study the effect of each synthetic parameter. In this work, we investigate the effect of surfactant on a ceramic-DR process, with copper oxide as the chosen material. To study the influence of surfactant; aminoalcohols (triethanolamine, diethanolamine, monoethanolamine), alkylamines (ethyl amine) and aqua ligands are chosen. Digestively ripened quantum dots (QDs) are formed in case of all surfactants except ethyl amine and water. Aminoalchols based surfactants which contain both hydroxyl and amine moieties are efficient ligands (due to their chelation ability) for achieving DR. With the increase of denticity of the ligand, average size of QDs do not vary; however the variance in size does. QDs formed using aminoalchols are more monodispersed when compared to alkyl amine and aqua ligand systems. Furthermore, absorption and photoluminescence spectra suggest that choice of surfactant is important for achieving DR in ceramic nanostructures (when compared to other parameters). Hard-soft-acid-base-interactions between surfactant and copper oxide seem primarily responsible for the observed DR in copper oxide QDs. The absorption and photoluminescence spectra indicate that the energy migration and relaxation pathways taking place in DR QDs depend on the type of capping agent used.

Wettability modification of Wender lignite by adsorption of dodecyl poly ethoxylated surfactants with different degree of ethoxylation: A molecular dynamics simulation study.

Science.gov (United States)

Zhang, Lei; Li, Bao; Xia, Yangchao; Liu, Shengyu

2017-09-01

Lignite is an important and useful fossil fuel in the world and the strong hydrophilicity of it limits its applications. Surfactant adsorption on lignite is an effective way to make it hydrophobic. In this work, aiming to examine the effect of the degree of ethoxylation on the adsorption behavior of dodecyl poly ethoxylated surfactants on lignite and the wettability modification of modified lignite by surfactant adsorption, different combined systems formed by surfactants, water and a model surface of Wender lignite have been studied using molecular dynamics simulation. The adsorption configurations vary with the degree of ethoxylation. At the same adsorption amounts, increasing the degree of ethoxylation can make the adsorption layer more compactness and bring stronger adsorption strength. The results of binding energy and its components show that the adsorption of alkyl polyoxyethylene ethers surfactant on lignite is physically adsorbed rather than electrostatically or chemisorbed. Meanwhile, van der Waals interaction plays a dominant role in the adsorption. The addition of surfactant could reduce the possibility of the interaction between water and lignite. Compared to the original lignite, the interaction between them is weakened after surfactant adsorption in water/surfactant/lignite system, thus strengthening the hydrophobicity of lignite. Similar to the adsorption strength, hydrophobicity of modified lignite increases with the increase of the degree of ethoxylation. The lignite surface properties are changed due to surfactant adsorption by analyzing the compositions of interaction energy and the change of hydrogen bonds. Copyright © 2017 Elsevier Inc. All rights reserved.

Thermodynamic insights into drug-surfactant interactions: Study of the interactions of naporxen, diclofenac sodium, neomycin, and lincomycin with hexadecytrimethylammonium bromide by using isothermal titration calorimetry.

Science.gov (United States)

Choudhary, Sinjan; Talele, Paurnima; Kishore, Nand

2015-08-01

The success of drug delivery depends on the efficiency of the route of administration, which in turn relies on properties of the drug and its transport vehicle. A quantitative knowledge of association of drugs with transport vehicles is lacking when the latter are in the category of self assembled structures. The work reported in this manuscript addresses the mechanism of partitioning of naproxen, diclofenac sodium, neomycin and lincomycin in the micelles of hexadecytrimethylammonium bromide and that is quantitatively based on the measurement of thermodynamic parameters of interactions by using isothermal titration calorimetry. The addressed mechanism of partitioning is based on the identification of the type of interactions of these drugs with the surfactant micelles and monomers, along with the effect of the former on the micellization properties of the surfactant. The conclusions are based on the interpretation of the values of partitioning constant, standard molar enthalpy change, standard molar entropy change and the stoichiometry of the interaction. The results of this study have implications for deriving guidelines for the target oriented synthesis of new drugs that are to be used for effective delivery via micellar media. Copyright © 2015 Elsevier B.V. All rights reserved.

Effects of a homologous series of linear alcohol ethoxylate surfactants on fathead minnow early life stages.

Science.gov (United States)

Lizotte, R E; Wong, D C; Dorn, P B; Rodgers, J H

1999-11-01

Effects of a homologous series of three primarily linear alcohol ethoxylate surfactants were studied in laboratory flow-through 28-day early-life-stage tests with fathead minnow (Pimephales promelas Rafinesque). Surfactants were a C(9-11), C(12-13), and C(14-15) with an average of 6, 6.5, and 7 ethylene oxide units per mole of alcohol, respectively. Average measured surfactant recoveries were 103%, 81%, and 79% of nominal concentrations for the C(9-11) EO 6, C(12-13) EO 6.5, and C(14-15) EO 7 studies, respectively. Embryo survival at 48 h was not adversely affected at any of the concentrations tested. Impaired hatching and deformed fry were observed only in the C(12-13) EO 6.5 study. The 28-day LC50 values were 4.87, 2.39, and 1.02 mg/L for the C(9-11) EO 6, C(12-13) EO 6.5, and C(14-15) EO 7 surfactants, respectively. The corresponding NOECs for survival were 1.01, 1.76, and 0.74 mg/L. Posthatch fry growth was more sensitive than survival for the C(12-13) EO 6.5 and C(14-15) EO 7 surfactants. Survival of posthatch fry decreased with increasing surfactant alkyl chain length. Twenty-eight-day laboratory data were compared to 96-h laboratory, 10-day laboratory and 30-day stream mesocosm data for fathead minnow previously determined for these surfactants. Survival endpoints from the different exposures were comparable and only varied within a factor of two. Similarity of results suggests that it is possible to effectively use 96-h, 10-day, or 28-day laboratory data to predict environmental effects concentrations of these surfactants for fish. http://link.springer-ny. com/link/service/journals/00244/bibs/37n4p536.html

Mixed Micelle System Produced by Interaction Between Transglycosylated Stevia and an Ionic Surfactant Improves Dissolution Profile of Mefenamic Acid.

Science.gov (United States)

Fujimori, Miki; Kadota, Kazunori; Tozuka, Yuichi

2017-04-01

Transglycosylated stevia (stevia-G) can effectively improve the dissolution and bioavailability of poorly water-soluble drugs. Furthermore, addition of an ionic surfactant to stevia-G solution has been shown to enhance the dissolution effect of stevia-G on flurbiprofen. Herein, 4 surfactants, namely sodium dodecyl sulfate, sodium N-dodecanoylsarcosinate, sodium monododecyl phosphate, and lauryltrimethylammonium chloride (LTAC) were screened to investigate their synergistic effect with stevia-G in enhancing the solubility of mefenamic acid (MFA). The ternary formulation containing LTAC produced the highest increase in solubility, whereas the binary MFA/LTAC formulation did not increase the solubility of MFA. Surface tension was evaluated to analyze the interaction between stevia-G and each ionic surfactant, wherein the Rubingh model was applied to predict mixed micelle formation between stevia-G and LTAC. Interaction parameters calculated by the Rubingh model reflected mixed micelle formation between stevia-G and LTAC relative to the self-interactions of the 2 individual surfactants. All interaction parameters in this system showed negative values, indicating a favorable interaction (e.g., hydrogen bond or electrostatic and dipole) between binary components in the mixed micelles. Spray-dried particles of ternary formulations (MFA/stevia-G/LTAC) were prepared to evaluate the dissolution profile and physicochemical properties. Dissolution profiling showed that the concentration of MFA released from spray-dried particles was significantly higher than untreated MFA. Copyright © 2017 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Temporal and geographical distributions of epilithic sodium dodecyl sulfate-degrading bacteria in a polluted South Wales river

Energy Technology Data Exchange (ETDEWEB)

Anderson, D.J.; Day, M.J.; Russell, N.J.; White, G.F.

1988-02-01

Epilithic bacteria were isolated nonselectively from riverbed stones and examined by gel zymography for their ability to produce alkylsulfatase (AS) enzymes and thus to metabolize alkyl sulfate surfactants such as sodium dodecyl sulfate. The percentages of AS+ isolates from stone epilithon at five sites from the source to the river mouth were measured on five sampling days spread over 1 year. The results showed that (i) the prevalence of epilithic AS+ strains (as a percentage of all isolates) was much higher at polluted sites than at the source; (ii) when averaged over the whole river, percentages of AS+ strains were significantly higher at the end of summer compared with either the preceding or the following winter; (iii) analysis of site-sampling time interactions indicated that water quality factors (e.g., biochemical oxygen demand and dissolved oxygen concentration) rather than climatic factors determined the distributions of epilithic AS+ isolates; (iv) constitutive strains were the most prevalent (7.2% of all isolates), with smaller numbers of isolates with inducible (4.5%) and repressible (1.7%) enzymes.

Kinetic and thermodynamic studies on the adsorption of anionic surfactant on quaternary ammonium cationic cellulose.

Science.gov (United States)

Zhang, Yuanzhang; Shi, Wenjian; Zhou, Hualan; Fu, Xing; Chen, Xuan

2010-06-01

Removal of anionic surfactants from aqueous solutions by adsorption onto quaternary ammonium cationic cellulose (QACC) was investigated. The effects of solution acidity, initial concentration, adsorption time, and temperature on the adsorption of sodium dodecyl-benzene sulfonate (SDBS), sodium lauryl sulfate (SLS), and sodium dodecyl sulfonate (SDS) were studied. The kinetic experimental data fit well with the pseudo-second-order model; the rate constant of the adsorption increased with temperature. The values of apparent activation energy for the adsorption were calculated as ranging from 10.2 to 17.4 kJ/ mol. The adsorption isotherm can be described by the Langmuir isotherm. The values of thermodynamic parameters (deltaH0, deltaS0, and deltaG0) for the adsorption indicated that this process was spontaneous and endothermic. At 318 K, the saturated adsorption capacities of QACC for SDBS, SLS, and SDS were 1.75, 1.53, and 1.39 mmol/g, respectively. The adsorption process was mainly chemisorption and partially physisorption. The results show that QACC is effective for the removal of anionic surfactants.

The Roll of NaPSS Surfactant on the Ceria Nanoparticles Embedding in Polypyrrole Films

Directory of Open Access Journals (Sweden)

Simona Popescu

2016-01-01

Full Text Available Cerium oxide nanoparticles (CeO2 NPs in crystalline form have been synthesized by a coprecipitation method. CeO2 nanoparticles were then embedded in polypyrrole (PPy films during the electropolymerization of pyrrole (Py on titanium substrate. The influence of poly(sodium 4-styrenesulfonate (NaPSS surfactant used during polymerization on the embedding of CeO2 NPs in polypyrrole films was investigated. The new films were characterized in terms of surface analysis, wettability, electrochemical behaviour, and antibacterial effect. The surface and electrochemical characterization revealed the role of surfactant on PPy doping process cerium oxide incorporation. In the presence of surfactant, CeO2 NPs are preferentially embedded in the polymeric film while, without surfactant, the ceria nanoparticles are quasiuniformly spread as agglomerates onto polymeric films. The antibacterial effect of studied PPy films was substantially improved in the presence of cerium oxide and depends by the polymerization conditions.

Formation of protein/surfactant adsorption layer at the air/water interface as studied by dilational surface rheology.

Science.gov (United States)

Mikhailovskaya, A A; Noskov, B A; Lin, S-Y; Loglio, G; Miller, R

2011-08-25

The dynamic dilatational surface elasticity of mixed solutions of globular proteins (β-lactoglobulin (BLG) and bovine serum albumin (BSA)) with cationic (dodecyltrimethylammonium bromide (DTAB)) and anionic (sodium dodecyl sulfate (SDS)) surfactants was measured as a function of the surfactant concentration and surface age. If the cationic surfactant concentration exceeds a certain critical value, the kinetic dependencies of the dynamic surface elasticity of BLG/DTAB and BSA/DTAB solutions become nonmonotonous and resemble those of mixed solutions of proteins with guanidine hydrochloride. This result indicates not only the destruction of the protein tertiary structure in the surface layer of mixed solution but also a strong perturbation of the secondary structure. The corresponding kinetic dependencies for protein solutions with added anionic surfactants are always monotonous, thereby revealing a different mechanism of the adsorption layer formation. One can assume that the secondary structure is destroyed to a lesser extent in the latter case and hinders the formation of loops and tails at the interface. The increase of the solution's ionic strength by the addition of sodium chloride results in stronger changes of the protein conformations in the surface layer and the appearance of a local maximum in the kinetic dependencies of the dynamic surface elasticity in a relatively narrow range of SDS concentration. © 2011 American Chemical Society

Sedimentation and deformation of an aqueous sodium hydroxide drop in vegetable oil

Science.gov (United States)

White, Andrew; Hyacinthe, Hyaquino; Ward, Thomas

2013-11-01

The addition of water droplets in fuels is known to provide benefits such as decreased Nitrous Oxide NOx emissions. Unfortunately the shelf life of a water-fuel emulsion is limited by the sedimentation rate of the water droplets. It is well known that adding surfactants can significantly slow the sedimentation rate due to the introduction of Marangoni stresses. In the case of a vegetable oil fuel, adding sodium hydroxide (NaOH) to the water droplets will produce surfactants through saponification in the form of sodium-carboxylate salts. Pendant drops of aqueous NaOH solutions with pH between 11 and 13 will be suspended in several oils such as corn, olive, canola and soybean oil in order to measure the interfacial tension. The change in interfacial tension with time will be used to estimate the surfactant concentration and the saponification rate. Then individual drops will be placed in the oils to observe the settling velocity and drop deformation. NSF CBET.

Atrazine and Diuron partitioning within a soil-water-surfactant system

Science.gov (United States)

Wang, P.; Keller, A.

2006-12-01

The interaction between pesticide and soil and water is even more complex in the presence of surfactants. In this study, batch equilibrium was employed to study the sorption of surfactants and the partitioning behaviors of Atrazine and Diuron within a soil-water-surfactant system. Five soils and four surfactants (nonionic Triton- 100, cationic Benzalkonium Chloride (BC), anionic Linear Alkylbenzenesulfonate (LAS), and anionic Sodium Dodecyl Sulfate (SDS)) were used. All surfactant sorption isotherms exhibited an initial linear increase at low surfactant concentrations but reached an asymptotic value as the surfactant concentrations increased. Among the surfactants, BC had the highest sorption onto all soils, followed by Triton-100 and then by LAS and SDS, implying that the nature of the charge significantly influences surfactant sorption. Sorption of either Triton-100 or BC was highly correlated with soil Cation Exchange Capacity (CEC) while that of LAS and SDS was complicated by the presence of Ca2+ and Mg2+ in the aqueous phase and the CEC sites. Both LAS and SDS formed complexes with Ca2+ and Mg2+, resulting in a significant decrease in the detergency of the surfactants. At high surfactant concentrations and with micelles present in the aqueous phase, the micelles formed a more competitive partitioning site for the pesticides, resulting in less pesticide sorbed to the soil. At low Triton-100 and BC concentration, the sorption of the surfactants first resulted in less Atrazine sorption but more Diuron sorption, implying competition between the surfactants and Atrazine, which serves as an indirect evidence that there is a different sorption mechanism for Atrazine. Atrazine is a weak base and it protonates and becomes positively charged near particle surfaces where the pH is much lower than in the bulk solution. The protonated Atrazine may then be held on the CEC sites via electrostatic attraction. Triton-100, LAS and SDS sorbed on the soil showed similar

Surfactant media for constant-current coulometry. Application for the determination of antioxidants in pharmaceuticals

Energy Technology Data Exchange (ETDEWEB)

Ziyatdinova, Guzel, E-mail: Ziyatdinovag@mail.ru [Analytical Chemistry Department, A.M. Butlerov Institute of Chemistry, Kazan (Volga Region) Federal University, Kremlyevskaya, 18, Kazan 420008 (Russian Federation); Ziganshina, Endzhe; Budnikov, Herman [Analytical Chemistry Department, A.M. Butlerov Institute of Chemistry, Kazan (Volga Region) Federal University, Kremlyevskaya, 18, Kazan 420008 (Russian Federation)

2012-09-26

Highlights: Black-Right-Pointing-Pointer Applicability of surfactants in constant-current coulometry is shown for the first time. Black-Right-Pointing-Pointer Reactions of antioxidants with electrogenerated titrants in surfactant media are investigated. Black-Right-Pointing-Pointer Water insoluble antioxidants can be determined in water media with addition of surfactants. Black-Right-Pointing-Pointer Coulometric determination of antioxidants in pharmaceutical dosage forms using surfactants media is developed. - Abstract: Effect of surfactant presence on electrochemical generation of titrants has been evaluated and discussed for the first time. Cationic (1-dodecylpyridinium and cetylpyridinium bromide), anionic (sodium dodecyl sulfate) and nonionic (Triton X100 and Brij{sup Registered-Sign} 35) surfactants as well as nonionic high molecular weight polymer (PEG 4000) do not react with the electrogenerated bromine, iodine and hexacyanoferrate(III) ions. The electrogenerated chlorine chemically interact with Triton X100 and Brij{sup Registered-Sign} 35. The allowable range of surfactants concentrations providing 100% current yield has been found. Chain-breaking low molecular weight antioxidants (ascorbic acid, rutin, {alpha}-tocopherol and retinol) were determined by reaction with the electrogenerated titrants in surfactant media. Nonionic and cationic surfactants can be used for the determination of antioxidants by reaction with the electrogenerated halogens. On contrary, cationic surfactants gives significantly overstated results of antioxidants determination with electrogenerated hexacyanoferrate(III) ions. The use of surfactants in coulometry of {alpha}-tocopherol and retinol provides their solubilization and allows to perform titration in water media. Simple, express and reliable coulometric approach for determination of {alpha}-tocopherol, rutin and ascorbic acid in pharmaceuticals using surfactant media has been developed. The relative standard deviation of the

Acid-base, optical and extraction properties of Rose Bengal in the presence of surfactants

International Nuclear Information System (INIS)

Lengyel, J.; Krtil, J.; Kuban, V.

1989-01-01

Changes in the optical and acid-base characteristics of Rose Bengal in the presence of cationic (Septones - SPX, hexadecyltrimethylammonium bromide - CTMAB and hexadecylpyridinium bromide - CPB), anionic (sodium dodecylsuulfate - SDS) and nonionic (Triton X-100) surfactants in submicellar and micellar concentrations were studied spectrophotometrically. The conditional dissociation constants of Rose Bengal pK ai * depend on the kind and concentration of cationic surfactant. Changes in pK ai * values are described in terms of formation of ion associates of the dye with the surfactant of the composition QHB and Q 2 B. The extraction constants of the ion associates in chloroform were determined radiometrically with the aid of Rose Bengal labelled with 131 I. (author). 4 figs., 3 tabs., 22 refs

Impact of surfactants on the target recognition of Fab-conjugated PLGA nanoparticles.

Science.gov (United States)

Kennedy, Patrick J; Perreira, Ines; Ferreira, Daniel; Nestor, Marika; Oliveira, Carla; Granja, Pedro L; Sarmento, Bruno

2018-06-01

Targeted drug delivery with nanoparticles (NPs) requires proper surface ligand presentation and availability. Surfactants are often used as stabilizers in the production of targeted NPs. Here, we evaluated the impact of surfactants on ligand functionalization and downstream molecular recognition. Our model system consisted of fluorescent poly(lactic-co-glycolic acid) (PLGA) NPs that were nanoprecipitated in one of a small panel of commonly-used surfactants followed by equivalent washes and conjugation of an engineered Fab antibody fragment. Size, polydispersity index and zeta potential were determined by dynamic light scattering and laser Doppler anemometry, and Fab presence on the NPs was assessed by enzyme-linked immunosorbent assay. Most importantly, Fab-decorated NP binding to the cell surface receptor was monitored by fluorescence-activated cell sorting. 2% polyvinyl alcohol, 1% sodium cholate, 0.5% Pluronic F127 (F127) and 2% Tween-80 were initially tested. Of the four surfactants tested, PLGA NPs in 0.5% F127 and 2% Tween-80 had the highest cell binding. These two surfactants were then retested in two different concentrations, 0.5% and 2%. The Fab-decorated PLGA NPs in 2% F127 had the highest cell binding. This study highlights the impact of common surfactants and their concentrations on the downstream targeting of ligand-decorated NPs. Similar principles should be applied in the development of future targeted nanosystems where surfactants are employed. Copyright © 2018 Elsevier B.V. All rights reserved.

[Alkylating agents].

Science.gov (United States)

Pourquier, Philippe

2011-11-01

With the approval of mechlorethamine by the FDA in 1949 for the treatment of hematologic malignancies, alkylating agents are the oldest class of anticancer agents. Even though their clinical use is far beyond the use of new targeted therapies, they still occupy a major place in specific indications and sometimes represent the unique option for the treatment of refractory diseases. Here, we are reviewing the major classes of alkylating agents and their mechanism of action, with a particular emphasis for the new generations of alkylating agents. As for most of the chemotherapeutic agents used in the clinic, these compounds are derived from natural sources. With a complex but original mechanism of action, they represent new interesting alternatives for the clinicians, especially for tumors that are resistant to conventional DNA damaging agents. We also briefly describe the different strategies that have been or are currently developed to potentiate the use of classical alkylating agents, especially the inhibition of pathways that are involved in the repair of DNA lesions induced by these agents. In this line, the development of PARP inhibitors is a striking example of the recent regain of interest towards the "old" alkylating agents.

Aggregation behavior and intermicellar interactions of cationic Gemini surfactants: Effects of alkyl chain, spacer lengths and temperature

International Nuclear Information System (INIS)

Hajy Alimohammadi, Marjan; Javadian, Soheila; Gharibi, Hussein; Tehrani-Bagha, Ali reza; Alavijeh, Mohammad Rashidi; Kakaei, Karim

2012-01-01

Graphical abstract: Highlights: → Enthalpy-entropy compensation relation was found between and for gemini surfactants. → The intermicellar interaction parameters are influenced with increasing the lengths of the tail and the spacer of gemini surfactants. → Increasing temperature decreases the intermicellar interaction parameters. → The changes in micellar surface charge density, and phase transition between spherical and rod geometries explain the data. - Abstract: The aggregation behavior of the cationic Gemini surfactants C m H 2m+1 N(CH 3 ) 2 (CH 2 ) S (CH 3 ) 2 N C m H 2m+1 ,2Br - with m = 12, 14 and s = 2, 4 were studied by performing surface tension, electrical conductivity, pulsed field gradient nuclear magnetic resonance (PFG-NMR), and cyclic voltammetry (CV) measurements over the temperature range 298 K to 323 K. The critical micelle concentration (CMC), surface excess (Γ max ), mean molecular surface area (A min ), degree of counter ion dissociation (α), and the thermodynamic parameters of micellization were determined from the surface tension and conductance data. An enthalpy-entropy compensation effect was observed and all the plots of enthalpy-entropy compensation exhibit excellent linearity. The micellar self-diffusion coefficients (D m ) and intermicellar interaction parameters (k d ) were obtained from the PFG-NMR and CV measurements. These results are discussed in terms of the intermicellar interactions, the effects of the chain and spacer lengths on the micellar surface charge density, and the phase transition between spherical and rod geometries. The intermicellar interaction parameters were found to decrease slightly with increasing temperature for 14-4-14, which suggests that the micellar surface charge density decreases with increasing temperature. The mean values of the hydrodynamic radius, R h , and the aggregation number, N agg , of the Gemini surfactants'm-4-m micelles were calculated from the micellar self-diffusion coefficient

Study on the surfactants present in atmospheric aerosols collected in the Okinawa Japan

Science.gov (United States)

Kamegawa, A.; Kasaba, T.; Shimabukuro, W.; Arakaki, T.

2017-12-01

The main constituent of atmospheric aerosols is organic substances, which occupy 20 to 70% of the mass. Organic matters in the aerosols contain organic acids, protein and humic acid, which behave similar to surfactants. Since surfactants contain both hydrophobic and hydrophilic functional groups in the molecule, they can play important roles in cloud formation and can affect climate change, but detailed mechanisms and magnitude are not well understood. In addition, surfactants can cause asthma, allergy, dry eye and so on. In this study, our aim is to characterize surfactants in the aerosols collected in different seasons in Okinawa, Japan. Atmospheric aerosols were collected at Cape Hedo Atmosphere and Aerosol Monitoring Station (CHAAMS) during Sep. 2013 and July 2014. Surfactants in the environment are comprised of artificially synthesized compounds and naturally derived organics so we only differentiate them into anionic and cationic surfactants. Colorimetric methods were used to determine the concentrations of anionic surfactants as methylene blue active substance (MBAS). Cationic surfactants were also measured by colorimetric method as disulfine blue active substance (DBAS) and showed always below detection limit. Thus, we only discuss anionic surfactants measured as MBAS. Water soluble organic carbon (WSOC) and metal concentrations were also measured for the same aerosol samples. Concentrations of MBAS in the studied samples were 2-3 times higher in spring, fall and winter than those collected in summer. MBAS concentration in the aerosols showed strong correlation with sulfate ion and WSOC, and slightly weaker correlation with nss-sulfate ion. Among the metals, only sodium ion showed a relatively strong correlation with MBAS concentrations. It is suggested that the anionic surfactants in the studied aerosols are mainly derived from marine sources.

Influences of surfactants on the preparation of copper nanoparticles by electron beam irradiation

Energy Technology Data Exchange (ETDEWEB)

Zhou Ruimin [Shanghai Applied Radiation Institute, Shanghai University, Shanghai 201800 (China)], E-mail: zhourm47@staff.shu.edu.cn; Wu Xinfeng; Hao Xufeng; Zhou Fei [Shanghai Applied Radiation Institute, Shanghai University, Shanghai 201800 (China); Li Hongbin [Department of Chemical Engineering and Technology, Shanghai University, Shanghai 201800 (China); Rao Weihong [Shenzhen Tianding Fine Chemical Engineering Manufacturing Co., Ltd., Shenzhen, Guangdong 518057 (China)

2008-02-15

Electron beam radiation was applied to prepare nano-size copper in water system using polyvinyl alcohol, sodium dodecyl benzene sulfonate, gluten and polyethylene glycol as the surfactants, respectively. The irradiated products were characterized by XRD, TEM and LSPSDA. The XRD and TEM showed that relative pure copper products with an average size of 20 nm, 40 nm and 20 nm can be obtained by using gluten, PEG and SDBS as surfactant, respectively. An admixture of copper and cuprous oxide was obtained in PVA system. The LSPSDA showed that the size of the Cu nanoparticles decreased with increasing the glutin concentration.

The self-organization and functional activity of binary system based on erucyl amidopropyl betaine - alkylated polyethyleneimine

Science.gov (United States)

Gaynanova, Gulnara A.; Valiakhmetova, Alsu R.; Kuryashov, Dmitry A.; Kudryashova, Yuliana R.; Lukashenko, Svetlana S.; Syakaev, Victor V.; Latypov, Shamil K.; Bukharov, Sergey V.; Bashkirtseva, Natalia Yu.; Zakharova, Lucia Ya.

2013-11-01

The self-organization in individual and binary aqueous solutions of a zwitterionic surfactant erucyl amidopropyl betaine and alkylated polyethyleneimine is carried out with a wide range of physical and chemical methods, including tensiometry, conductometry, dynamic light scattering, pH-metry, spectrophotometry, and fluorescence spectroscopy. The data obtained strongly support the formation of nanosized aggregates in the systems and provide information on their structure and probable morphological transitions. High solubilization capacity and data on the contact angle showed a possibility of the application of these systems as nanocontainers or oil wetting agents in the oil recovery.

Novel star-like surfactant as dispersant for multi-walled carbon nanotubes in aqueous suspensions at high concentration

Science.gov (United States)

Qiao, Min; Ran, Qianping; Wu, Shishan

2018-03-01

A kind of novel surfactant with star-like molecular structure and terminated sulfonate was synthesized, and it was used as the dispersant for multi-walled carbon nanotubes (CNTs) in aqueous suspensions compared with a traditional single-chained surfactant. The star-like surfactant showed good dispersing ability for multi-walled CNTs in aqueous suspensions. Surface tension analysis, total organic carbon analysis, X-ray photoelectron spectroscopy, zeta potential, dynamic light scattering and transmission electron microscopy were performed to research the effect of star-like surfactant on the dispersion of multi-walled CNTs in aqueous suspensions. With the assistance of star-like surfactant, the CNTs could disperse well in aqueous suspension at high concentration of 50 g/L for more than 30 days, while the CNTs precipitated completely in aqueous suspension after 1 day without any dispersant or after 10 days with sodium 4-dodecylbenzenesulfonic acid as dispersant.

Sodium phthalamates as corrosion inhibitors for carbon steel in aqueous hydrochloric acid solution

International Nuclear Information System (INIS)

Flores, Eugenio A.; Olivares, Octavio; Likhanova, Natalya V.; Dominguez-Aguilar, Marco A.; Nava, Noel; Guzman-Lucero, Diego; Corrales, Monica

2011-01-01

Highlights: → N-Alkyl-sodium phthalamates as corrosion inhibitors for industry in acidic medium. → Compounds behaved as mixed type inhibitors and followed Langmuir adsorption isotherm. → Efficiencies were proportional to aliphatic chain length and inhibitor concentration. → Iron complexes and chelates with phthalamates contributed to carbon steel protection. - Abstract: Three compounds of N-alkyl-sodium phthalamates were synthesized and tested as corrosion inhibitors for carbon steel in 0.5 M aqueous hydrochloric acid. Tests showed that inhibitor efficiencies were related to aliphatic chain length and dependent on concentration. N-1-n-tetradecyl-sodium phthalamate displayed moderate efficiency against uniform corrosion, 42-86% at 25 deg. C and 25-60% at 40 o C. Tests indicated that compounds behave as mixed type inhibitors where molecular adsorption on steel followed Langmuir isotherm, whereas thermodynamic suggested that a physisorption process occurred. XPS analysis confirmed film formation on surface, where Fe +2 complexes and Fe +2 chelates with phthalamates prevented steel from further corrosion.

REMOVAL OF ANIONIC SURFACTANTS FROM WASTEWATER BY MAGNETIC MINERAL SORBENTS

Directory of Open Access Journals (Sweden)

Oksana Vladimirova Makarchuk

2016-07-01

Full Text Available The simplest and most effective method of removing low concentrations of anionic surfactants such as sodium dodecyl benzenesulfonate (SDBS and sodium lauryl sulfate (SLS is adsorption. Among adsorbents the natural clays are cheap and promising for these purposes. However, there are significant difficulties in removal of spent sorbent after the adsorption process. So, the creation of magnetic sorbents that can be effectively removed from water after sorption by magnetic separation will be a successful decision. The aim of this investigation is the creation of cheap and efficient magnetic sorbents based on natural clays and magnetite for anionic surfactant removal from wastewater. We have synthesized a series of magnetic sorbents from different natural clays with a content of magnetite from 2 to 10 wt%. The ability of magnetic sorbents to remove SDBS and SLS from aqueous solutions has been studied for different adsorbate concentrations by varying the amount of adsorbent, temperature and shaking time. Thermodynamic parameters were calculated from the slope and intercept of the linear plots of ln K against 1/T. Analysis of adsorption results obtained at different temperatures showed that the adsorption pattern on magnetic sorbents correspond to the Langmuir isotherm. It is shown that with increasing the content of magnetite in the magnetic sorbents improves not only their separation from water by magnetic separation, but adsorption capacity to SDBS and SLS. Thus, we obtained of cheap magnetic sorbents based on natural clays and magnetite by the easy way, which not only quickly separated from the solution by magnetic separation, but effectively remove anionic surfactants.

Estudo das dispersões aquosas de nanotubos de carbono utilizando diferentes surfactantes Study of aqueous dispersions of carbon nanotubes using different surfactants

Directory of Open Access Journals (Sweden)

Isabella R. da Silva

2013-01-01

Full Text Available The dispersion of carbon nanotubes in water for their utilization in nanoscale devices is a challenging task. Comparative studies on interaction and dispersion of multi-wall carbon nanotubes (MWNT using two different surfactants (sodium dodecyl sulfate, SDS, and polyoxyethylenesorbitanmonooleate, Tween 80 are presented. The interaction between carbon nanotubes and surfactants was studied by tensiometry, conductivimetry, and fluorimetry. The dispersions of MWNT in surfactants were characterized using a UV-vis spectrophotometer. For effective dispersion, the minimum weight ratio of MWNT to surfactant was 1:41 and 1:3 for SDS and Tween 80, respectively.

The Scarlet Letter of Alkylation: A Mini Review of Selective Alkylating Agents

OpenAIRE

Oronsky, Bryan T; Reid, Tony; Knox, Susan J; Scicinski, Jan J

2012-01-01

If there were a stigma scale for chemotherapy, alkylating agents would be ranked at the top of the list. The chemical term alkylation is associated with nonselective toxicity, an association that dates back to the use of nitrogen mustards during World War I as chemical warfare agents. That this stigma persists and extends to compounds that, through selectivity, attempt to “tame” the indiscriminate destructive potential of alkylation is the subject of this review. Selective alkylation, as it i...

Mechanism of the protective effects of long chain n-alkyl glucopyranosides against ultrasound-induced cytolysis of HL-60 cells.

Science.gov (United States)

Cheng, Jason Y; Riesz, Peter

2007-07-01

Recently it has been shown that long chain (C5-C8) n-alkyl glucopyranosides completely inhibit ultrasound-induced cytolysis [J.Z. Sostaric, N. Miyoshi, P. Riesz, W.G. DeGraff, and J.B. Mitchell, Free Radical Biol. Med., 39 (2005) 1539]. This protective effect has possible applications in HIFU (high intensity focused ultrasound) for tumor treatment, and in ultrasound assisted drug delivery and gene therapy. n-Alkyl glucopyranosides with hexyl (5mM), heptyl (3mM), octyl (2mM) n-alkyl chains protected 100% of HL-60 cells in vitro from 1.057 MHz ultrasound-induced cytolysis under a range of conditions that resulted in 35-100% cytolysis in the absence of glucopyranosides. However the hydrophilic methyl-beta-d-glucopyranoside did not protect cells. The surface active n-alkyl glucopyranosides accumulate at the gas-liquid interface of cavitation bubbles. The OH radicals and H atoms formed in collapsing cavitation bubbles react by H-atom abstraction from either the n-alkyl chain or the glucose moiety of the n-alkyl glucopyranosides. Owing to the high concentration of the long chain surfactants at the gas-liquid interface of cavitation bubbles, the initially formed carbon radicals on the alkyl chains are transferred to the glucose moieties to yield radicals which react with oxygen leading to the formation of hydrogen peroxide. In this work, we find that the sonochemically produced hydrogen peroxide yields from oxygen-saturated solutions of long chain (hexyl, octyl) n-alkyl glucopyranosides at 614 kHz and 1.057 MHz ultrasound increase with increasing n-alkyl glucopyranoside concentration but are independent of concentration for methyl-beta-D-glucopyranoside. These results are consistent with the previously proposed mechanism of sonoprotection [J.Z. Sostaric, N. Miyoshi, P. Riesz, W.G. DeGraff, and J.B. Mitchell, Free Radical Biol. Med., 39 (2005) 1539]. This sequence of events prevents sonodynamic cell killing by initiation of lipid peroxidation chain reactions in cellular

Effect of surfactant on single drop mass transfer for extraction of aromatics from lubricating oils

Science.gov (United States)

Izza, H.; Ben Abdessalam, S.; Korichi, M.

2018-03-01

Solvent extraction is an effective method for the reduction of the content of aromatic of lubricating oil. Frequently, with phenol, furfural, the NMP (out of N-methyl pyrrolidone). The power solvent and the selectivity can be still to increase while using surfactant as additive which facilitates the separation of phase and increases the yeild in raffinat. Liquid-liquid mass transfer coefficients for single freely rising drops in the presence of surfactant in an extraction column have been investigated. The surfactant used in this study was sodium lauryl ether sulfate (SLES). The experiments were performed by bubbling a solvent as a series of individual drops from the top of the column containing furfural-SLES solution. The column used in this experiment was made from glass with 17 mm inner diameter and a capacity of 125ml. The effects of the concentration of surfactant on the overall coefficient of mass transfer was investigated.

Discrepancies over the onset of surfactant monomer aggregation interpreted by fluorescence, conductivity and surface tension methods

Directory of Open Access Journals (Sweden)

Maria de Fátima Carvalho Costa

1998-06-01

Full Text Available Molecular probe techniques have made important contributions to the determination of microstructure of surfactant assemblies such as size, stability, micropolarity and conformation. Conductivity and surface tension were used to determine the critical aggregation concentration (cac of polymer-surfactant complexes and the critical micellar concentration (cmc of aqueous micellar aggregates. The results are compared with those of fluorescent techniques. Several surfactant systems were examined, 1-butanol-sodium dodecylsulfate (SDS mixtures, solutions containing poly(ethylene oxide-SDS, poly(vinylpyrrolidone-SDS and poly(acrylic acid-alkyltrimethylammonium bromide complexes. We found differences between the cac and cmc values obtained by conductivity or surface tension and those obtained by techniques which use hydrophobic probe.

Phase transitions in surfactant monolayers

International Nuclear Information System (INIS)

Casson, B.D.

1998-01-01

Two-dimensional phase transitions have been studied in surfactant monolayers at the air/water interface by sum-frequency spectroscopy and ellipsometry. In equilibrium monolayers of medium-chain alcohols C n H 2n+1 OH (n = 9-14) a transition from a two-dimensional crystalline phase to a liquid was observed at temperatures above the bulk melting point. The small population of gauche defects in the solid phase increased only slightly at the phase transition. A model of the hydrocarbon chains as freely rotating rigid rods allowed the area per molecule and chain tilt in the liquid phase to be determined. The area per molecule, chain tilt and density of the liquid phase all increased with increasing chain length, but for each chain length the density was higher than in a bulk liquid hydrocarbon. In a monolayer of decanol adsorbed at the air/water interface a transition from a two-dimensional liquid to a gas was observed. A clear discontinuity in the coefficient of ellipticity as a function of temperature showed that the transition is first-order. This result suggests that liquid-gas phase transitions in surfactant monolayers may be more widespread than once thought. A solid-liquid phase transition has also been studied in mixed monolayers of dodecanol with an anionic surfactant (sodium dodecyl sulphate) and with a homologous series of cationic surfactants (alkyltrimethylammonium bromides: C n TABs, n = 12, 14, 16). The composition and structure of the mixed monolayers was studied above and below the phase transition. At low temperatures the mixed monolayers were as densely packed as a monolayer of pure dodecanol in its solid phase. At a fixed temperature the monolayers under-went a first-order phase transition to form a phase that was less dense and more conformationally disordered. The proportion of ionic surfactant in the mixed monolayer was greatest in the high temperature phase. As the chain length of the C n TAB increased the number of conformational defects

The influence of synthetic food additives and surfactants on the body weight of larvae of Tenebrio molitor (Coleoptera, Tenebrionidae

Directory of Open Access Journals (Sweden)

V. O. Martynov

2017-08-01

Full Text Available The broad spectrum of negative effects of food additives and surfactants on living organisms and the environment in general indicate a necessity of a detailed study on this issue. The aim of this article is to evaluate the impact of food additives and surfactants in a concentration of 350 mg/kg of fodder on the body weight of third age Tenebrio molitor Linnaeus, 1758 (Coleoptera, Tenebrionidae larvae. A significant change in the body weight of T. molitor larvae was observed when they consumed a diet containing 350 mg/kg of sodium glutamate, sodium cyclamate and sodium benzoate. We observed a tendency towards increase in body weight after addition of the food colouring Allura Red, saccharin, benzoic acid, betaine, emulsifying wax, AOS and SLES, and also we observed a decrease in body weight after addition of Tartrazine and Indigo Carmine in the same concentration. Out of the 18 tested food additives, 3 significantly stimulated an increase in the body weight of third age T. molitor larvae, and 3 manifested the same effect at the level of tendency (stimulated an increase in mass on average by 43–58% over the 14-day experiment, and 2 caused decrease in the body weight of larvae. Also, the 4 studied surfactants manifested a tendency towards increase in the body weight of T. molitor. This study on the impact of food additives and surfactants on organisms of insects is of great significance for protecting rare species of insects.

An investigation of chitosan and sodium dodecyl sulfate interactions in acetic media

Directory of Open Access Journals (Sweden)

Petrović Lidija B.

2016-01-01

Full Text Available Polymer/surfactant association is a cooperative phenomenon where surfactant binds to the polymer in the form of aggregates, usually through electrostatic or hydrophobic forces. As already known, polyelectrolytes may interact with oppositely charged surfactants through electrostatic attraction that results in polymer/surfactant complex formation. This behavior could be desirable in wide range of application of polymer/surfactant mixtures, such as improving colloid stability, gelling, emulsification and microencapsulation. In the present study surface tension, turbidity, viscosity and electrophoretic mobility measurements were used to investigate interactions of cationic polyelectrolyte chitosan (Ch and oppositely charged anionic surfactant, sodium dodecyl sulfate (SDS, in buffered water. Obtained results show the presence of interactions that lead to Ch/SDS complexes formation at all investigated pH and for all investigated polymer concentrations. Mechanisms of interaction, as well as characteristics of formed Ch/SDS complexes, are highly dependent on their mass ratio in the mixtures, while pH has no significant influence. [Projekat Ministarstva nauke Republike Srbije, br. II46010

Isobutane/olefin-alkylation

Energy Technology Data Exchange (ETDEWEB)

Waitkamp, J.; Maixner, S.

1983-11-01

Isobutane/olefin-alkylation - technology and reaction mechanism of a refinery process for production of high octane gasoline components: The alkylation of i-butane with olefins, especially with butenes, is a process for the conversion of light byproducts of a catalytic cracker to high quality gasoline components. Alkylate is a complex mixture of i-paraffins containing 5 to ca. 12 carbon atoms. Due to their octane numbers the four trimethylpentane isomers are the most desirable product components. Indeed, under optimum process conditions these isomers are the main products. Presently, alkylation capacity in the western world amounts to more than 40x10/sup 6/ t/a. Most units are located in the USA. Two liquid-phase processes using sulfuric acid and hydrofluoric acid, respectively, are of commercial importance. At present, there is a definite trend towards HF-alkylation. The reaction mechanism which proceeds via carbocations, is extremely complex. It is composed of a great variety of individual steps. Modern mechanistic concepts are discussed.

Molecular organization and dynamics of micellar phase of polyelectrolyte-surfactant complexes: ESR spin probe study

Science.gov (United States)

Wasserman, A. M.; Kasaikin, V. A.; Zakharova, Yu. A.; Aliev, I. I.; Baranovsky, V. Yu.; Doseva, V.; Yasina, L. L.

2002-04-01

Molecular dynamics and organization of the micellar phase of complexes of linear polyelectrolytes with ionogenic and non-ionogenic surfactants was studied by the ESR spin probe method. Complexes of polyacrylic acid (PAA) and sodium polystyrenesulfonate (PSS) with alkyltrimethylammonium bromides (ATAB), as well as complexes of poly- N, N'-dimethyldiallylammonium chloride (PDACL) with sodium dodecylsulfate (SDS) were studied. The micellar phase of such complexes is highly organized molecular system, molecular ordering of which near the polymeric chain is much higher than in the 'center' of the micelle, it depends on the polymer-detergent interaction, flexibility of polymeric chain and length of carbonic part of the detergent molecule. Complexes of polymethacrylic acid (PMAA) with non-ionic detergent (dodecyl-substituted polyethyleneglycol), show that the local mobility of surfactant in such complexes is significantly lower than in 'free' micelles and depends on the number of micellar particles participating in formation of complexes.

"Phase diagrams of Lecithin-based microemulsions containing Sodium Salicylate "

Directory of Open Access Journals (Sweden)

"Aboofazeli R

2000-08-01

Full Text Available Partial phase diagrams were constructed at 25°C to investigate the phase behaviour of systems composed of soybean lecithin, water, sodium salicylate, alcohol and isopropyl myristate. The lecithins used were the commercially available soy bean lecithins, namely E200 and E170 (phosphatidyl choline purities greater than 95% and 68-72% respectively. The cosurfactants employed were n-propanol, 2-propanol and n-butanol and these were used at lecithin/alcohol weight ratios (Km of 1:1 and 1.5:1. At a given Km, the aqueous phase consisted of a 2% w/w sodium salicylate solution. Phase diagrams showed the area of existence of a stable isotropic region along the surfactant/oil axis (i.e., reverse microemulsion area. The extension of the microemulsion domain was influenced by the purity of surfactant, the lecithin/alcohol weight ratios and the kind of the alcohol.

Effect of Surfactants on the Deformation and Detachment of Oil Droplets in a Model Laminar Flow Cell

Directory of Open Access Journals (Sweden)

Fréville V.

2013-10-01

Full Text Available Sugar-based surfactants are increasingly present in the development of eco-friendly detergents due to current regulations and consumer demand. In order to assess the degreasing performance of these new surfactants, the behavior of model oil droplets subjected to the action of a flow of surfactant solutions of different concentrations was studied in a laminar flow cell and related to the physico-chemical properties measured at the liquid/liquid (interfacial tension and solid/liquid/liquid interfaces (contact angle. With the surfactant solutions and the model oils employed in this study, three main behaviors were observed when a critical flow rate was reached: elongation, fragmentation or spontaneous detachment of the droplet. The analysis of the results leads to a correlation between the droplet behavior and the balance of the forces applied on the droplet in its initial position, in particular the gravity force Fg, which tends to move the oil droplet upwards (given the density difference, and the capillary force Fc, which tends to keep the droplet spherical. A state diagram could be established, based on the dimensionless Bond number (Fg/Fc and cosθ, θ being the initial contact angle of the drop on the surface before the establishment of the flow. One can thus predict the droplet behavior as a function of the system initial characteristics. The results allowed the comparison of degreasing performance of the different surfactants used and illustrated the potential of AlkylPolyPentosides (APP for detergent formulations.

Properties of diclofenac sodium sorption onto natural zeolite modified with cetylpyridinium chloride.

Science.gov (United States)

Krajišnik, Danina; Daković, Aleksandra; Milojević, Maja; Malenović, Anđelija; Kragović, Milan; Bogdanović, Danica Bajuk; Dondur, Vera; Milić, Jela

2011-03-01

In this study an investigation of a model drug sorption onto cationic surfactant-modified natural zeolites as a drug formulation excipient was performed. Natural zeolite was modified with cetylpyridinium chloride in amounts equivalent to 100, 200 and 300% of its external cation-exchange capacity. The starting material and obtained organozeolites were characterized by Fourier transform infrared spectroscopy, zeta potential measurements and thermal analysis. In vitro sorption of diclofenac sodium as a model drug was studied for all surfactant/zeolite composites by means of sorption isotherm measurements in aqueous solutions (pH 7.4). The modified zeolites with three levels of surfactant coverage within the short activation time were prepared. Zeta potential measurements and thermal analysis showed that when the surfactant loading level was equal to external cation-exchange value, almost monolayer of organic phase were present at the zeolitic surface while higher amounts of surfactant produced less extended bilayers, ordered bilayers or admicelles at the zeolitic surface. Modified zeolites, obtained in this manner, were effective in diclofenac sodium sorption and the organic phase derived from adsorbed cetylpyridinium chloride was the primary sorption phase for the model drug. The Langmuir isotherm was found to describe the equilibrium sorption data well over the entire concentration range. The separate contributions of the adsorption and partition to the total sorption of DS were analyzed mathematically. Results revealed that that adsorption and partitioning of the model drug take place simultaneously. 2010 Elsevier B.V. All rights reserved.

The effect of octylglucoside and sodium cholate in Staphylococcus epidermidis and Pseudomonas aeruginosa adhesion to soft contact lenses.

Science.gov (United States)

Santos, Lívia; Rodrigues, Diana; Lira, Madalena; Oliveira, Rosario; Real Oliveira, M Elisabete C D; Vilar, Eva Yebra-Pimentel; Azeredo, Joana

2007-05-01

In this study, the effect of the natural surfactants octylglucoside and sodium cholate in inhibiting Staphylococcus epidermidis and Pseudomonas aeruginosa adhesion to conventional and silicone-hydrogel contact lenses (CL) was assessed. Hydrophobicity was also evaluated to conditioned and nonconditioned CL. The inhibiting effect of the tested surfactants was determined through "in vitro" adhesion studies to conditioned and nonconditioned CL followed by image acquisition and cell enumeration. Hydrophobicity was evaluated through contact angle measurements using the advancing type technique on air. Sodium cholate exhibits a very low capability to inhibit microbial adhesion. Conversely, octylglucoside effectively inhibited microbial adhesion in both types of lenses. This surfactant exhibited an even greater performance than a multipurpose lens care solution used as control. Octylglucoside was the only tested surfactant able to lower the hydrophobicity of all CL, which can explain its high performance. The results obtained in this study point out the potential of octylglucoside as a conditioning agent to prevent microbial colonization.

Effect of anionic surfactant concentration on the variable range hopping conduction in polypyrrole nanoparticles

International Nuclear Information System (INIS)

Rawal, Ishpal; Kaur, Amarjeet

2014-01-01

The mechanism of charge transport in polypyrrole (PPy) nanoparticles prepared with different concentrations (5 to 30 mM) of anionic surfactant (sodium dodecyl sulfate) is reported. Transmission electron microscopy technique confirms the formation of PPy nanoparticles of sizes ∼52 to 28 nm under surfactant directed approach. The room temperature electrical conductivity of the prepared nanoparticles found to increase from 3 to 22 S/cm with surfactant concentration. The temperature dependent activation energy rules out the possibility of band conduction mechanism in the prepared PPy nanoparticles and thus the synthesized nanoparticles are analyzed under variable range hopping (VRH) model for conduction mechanism. The PPy nanoparticles, reduced with liquid ammonia, hold 3D VRH conduction mechanism for the charge transport. However, in the doped samples, some deviation from 3D VRH conduction behavior at higher temperatures (>150 K) has been observed. This may be attributed to the presence of anionic surfactant in these samples. The doping of anionic surfactant causes rise in conducting islands, which may lead to the change in the shape/distribution of density of states governed by Gaussian or exponential type near Fermi level

Effect of anionic surfactant concentration on the variable range hopping conduction in polypyrrole nanoparticles

Science.gov (United States)

Rawal, Ishpal; Kaur, Amarjeet

2014-01-01

The mechanism of charge transport in polypyrrole (PPy) nanoparticles prepared with different concentrations (5 to 30 mM) of anionic surfactant (sodium dodecyl sulfate) is reported. Transmission electron microscopy technique confirms the formation of PPy nanoparticles of sizes ˜52 to 28 nm under surfactant directed approach. The room temperature electrical conductivity of the prepared nanoparticles found to increase from 3 to 22 S/cm with surfactant concentration. The temperature dependent activation energy rules out the possibility of band conduction mechanism in the prepared PPy nanoparticles and thus the synthesized nanoparticles are analyzed under variable range hopping (VRH) model for conduction mechanism. The PPy nanoparticles, reduced with liquid ammonia, hold 3D VRH conduction mechanism for the charge transport. However, in the doped samples, some deviation from 3D VRH conduction behavior at higher temperatures (>150 K) has been observed. This may be attributed to the presence of anionic surfactant in these samples. The doping of anionic surfactant causes rise in conducting islands, which may lead to the change in the shape/distribution of density of states governed by Gaussian or exponential type near Fermi level.

Effect of cationic/anionic organic surfactants on evaporation induced self assembled tin oxide nanostructured films

International Nuclear Information System (INIS)

Khun Khun, Kamalpreet; Mahajan, Aman; Bedi, R.K.

2011-01-01

Tin oxide nanostructures with well defined morphologies have been obtained through an evaporation induced self assembly process. The technique has been employed using an ultrasonic nebulizer for production of aersol and its subsequent deposition onto a heated glass substrate. The precursor used for aersol production was modified by introducing cationic and anionic surfactants namely cetyl trimethyl ammonium bromide and sodium dodecyl sulphate respectively. The effect of surfactants on the structural, electrical and optical properties of self assembled tin oxide nanostructures were investigated by using X-ray diffraction, field emission scanning electroscope microscopy, two probe technique and photoluminiscence studies. The results reveal that high concentration of surfactants in the precursor solution leads to reduction in crystallite size with significant changes in the morphology of tin oxide nanostructures. Photoluminiscence studies of the nanostructures show emissions in the visible region which exhibit marked changes in the intensities upon variation of surfactants in the precursor solutions.

Effect of cationic/anionic organic surfactants on evaporation induced self assembled tin oxide nanostructured films

Energy Technology Data Exchange (ETDEWEB)

Khun Khun, Kamalpreet [Material Science Laboratory, Department of Physics, Guru Nanak Dev University, Amritsar 143005 (India); Mahajan, Aman, E-mail: dramanmahajan@yahoo.co.in [Material Science Laboratory, Department of Physics, Guru Nanak Dev University, Amritsar 143005 (India); Bedi, R.K. [Material Science Laboratory, Department of Physics, Guru Nanak Dev University, Amritsar 143005 (India)

2011-01-15

Tin oxide nanostructures with well defined morphologies have been obtained through an evaporation induced self assembly process. The technique has been employed using an ultrasonic nebulizer for production of aersol and its subsequent deposition onto a heated glass substrate. The precursor used for aersol production was modified by introducing cationic and anionic surfactants namely cetyl trimethyl ammonium bromide and sodium dodecyl sulphate respectively. The effect of surfactants on the structural, electrical and optical properties of self assembled tin oxide nanostructures were investigated by using X-ray diffraction, field emission scanning electroscope microscopy, two probe technique and photoluminiscence studies. The results reveal that high concentration of surfactants in the precursor solution leads to reduction in crystallite size with significant changes in the morphology of tin oxide nanostructures. Photoluminiscence studies of the nanostructures show emissions in the visible region which exhibit marked changes in the intensities upon variation of surfactants in the precursor solutions.

Evaluation of acute and chronic toxicity of DSS and LAS surfactants undergoing the irradiation with electron beam

International Nuclear Information System (INIS)

Romanelli, Maria Fernanda

2004-01-01

Surfactants are synthetic organic compounds widely used in cosmetic, food, textile, dyers and paper production industries and in particular detergents and others cleaning products industries. The world consumption is nearly 8 million tons per year. One of the main environmental issues coming from the use of these compounds is their toxicity that compromises the biological treatment of effluents and the quality of receiving waters. The objective of this work was the application of ionizing radiation by electron beam in the degradation and reduction of acute and chronic toxicities of surfactants sodium dodecylsulfate (SDS), dodecyl p-benzenesulfonate acid (LAS) and sodium dodecyl p-benzenesulfonate (LAS). This treatment technology has been studied as a pre-treatment for effluents containing toxic and non-biodegradable compounds, before the biological treatment. Two acute toxicity assays were employed, one with the micro-crustacean Daphnia similis and the other with the luminescent bacterium Vibrio fischeri along with a chronic toxicity assay with the micro-crustacean Ceriodaphnia dubia (just for SDS and acid LAS) for the non-irradiated and irradiated samples and radiation doses 3.0 kGy, 6.0 kGy, 9.0 kGy and 12.0 kGy. Physical-chemical parameters were evaluated for the following up the degradation of the surfactant molecules. The reductions of acute toxicity varied between 72.49% and 90.98% for SDS, 18.22% and 78.98% for acid LAS and 82.66% and 94.26% for sodium LAS. For the chronic toxicity, the reduction percentages varied between 64.03% and 83.01% for SDS and 47.48% and 64.91% for acid LAS. When one considers the application of the electron beam as a pre-treatment of effluents containing high concentrations of surfactants, the toxicity is an essential parameter allowing the further biological treatment of these effluents. (author)

Adsorption Of Surfactants At the Water-Oil Interface By Short-Time Diffusion

Science.gov (United States)

Cortes-Estrada, Aldo; Ibarra-Bracamontes, Laura; Aguilar-Corona, Alicia; Viramontes-Gamboa, Gonzalo

2017-11-01

Surface tension is an important parameter for different industrial processes. The addition of surfactants can modify the interfacial tension between two fluids. As the surfactant molecules reach and are adsorbed at a fluid interface, the surface tension or interfacial tension is reduced until the interface is saturated. Dynamic Interfacial tension measurements were carried out using an optical tensiometer by the Pendant Drop technique at a room temperature of 25 °C for a period of 250 sec. A drop of surfactant solution was deposited and allowed to diffuse into a water-oil interface, and then the adsorption rate at the interface was calculated. Sodium Dodecyl Sulfate (SDS) was used as the surfactant, hexane and dodecane were tested as the oil phase. A linear decay in the interfacial tension was observed for the lower initial concentrations of the order of 0.0001 to 0.01 mM, and an exponential decay was observed for initial concentrations of the order of 0.1 to 1 mM. This study was supported by the Mexican Council of Science and Technology (CONACyT) and by the Scientific Research Coordination of the University of Michoacan in Mexico.

Effects of Surfactants on the Performance of CeO2 Humidity Sensor

Directory of Open Access Journals (Sweden)

Chunjie Wang

2014-01-01

Full Text Available Nanosized CeO2 powders were synthesized via hydrothermal method with different types of surfactants (polyethylene glycol (PEG, cetyltrimethylammonium bromide (CTAB, and sodium dodecylbenzenesulfonate (SDBS. X-ray diffraction, Raman spectroscopy, and transmission electron microscopy were utilized to characterize the phase structures and morphologies of the products. The sample with CTAB as surfactant (CeO2-C has the largest specific surface area and the smallest particle size among these three samples. The humidity sensor fabricated by CeO2-C shows higher performance than those used CeO2-P and CeO2-S. The impedance of the CeO2-C sensor decreases by about five orders of magnitude with relative humidity (RH changing from 15.7 to 95%. The response and recovery time are 7 and 7 s, respectively. These results indicate that the performance of CeO2 humidity sensors can be improved effectively by the addition of cationic surfactant.

Effect of foamability index of short chain alkyl amines on flotation of quartz

Directory of Open Access Journals (Sweden)

Szczerkowska Sabina

2016-01-01

Full Text Available Amines can be used for flotation of various minerals, especially quartz. The flotation efficiency of quartz depends on the amine type and dose. It was proved that the shorter alkyl amine, higher amine concentration has to be used to recover quartz at the same level. In flotation amines play a role of both collectors and frothers. The ability of a amine to collect particles can be expressed in the form of contact angle, while the foaming properties by different parameters including dynamic foamability index (DFI and critical coalescence concentration (CCC. Determination of DFI and CCC requires advanced techniques and methods. Therefore, in this paper a rapid and facile method for determination of foaming properties of amines and also other surfactants was used. It was based on measuring the initial foam and froth heights in a conventional flotation machine at different concentrations of surfactants. The foam height-concentration curve was described by utilizing an empirical equation which was based on one-adjustable parameter called the foamability index (FI. In this work the foamability index was determined for butylamine (ButNH2, hexylamine (HexNH2 and octylamine (OctNH2 as examples of short chain alkyl amines. The determined foamability indices were 92, 12 and 4 mg/dm3 for ButNH2, HexNH2 and OctNH2, respectively. It was shown that when the flotation results of quartz were presented in the form of recovery versus normalized amine concentration in relation to the foamability index (c/FI, all the experimental data points converged to one curve. It indicates that amines act similarly but at different concentrations expressed as FI. The foamability index seems to be a useful parameter for characterizing any flotation frother.

Interfacial properties of chitosan/sodium dodecyl sulfate complexes

Directory of Open Access Journals (Sweden)

Milinković Jelena R.

2017-01-01

Full Text Available Contemporary formulations of cosmetic and pharmaceutical emulsions may be achieved by using combined polymer/surfactant system, which can form complexes with different structure and physicochemical properties. Such complexation can lead to additional stabilization of the emulsion products. For these reasons, the main goal of this study was to investigate the interfacial properties of chitosan/sodium dodecyl sulfate complexes. In order to understand the stabilization mechanism, the interface of the oil/water systems that contained mixtures of chitosan and sodium dodecyl sulfate, was studied by measuring the interfacial tension. Considering the fact that the properties of the oil phase has influence on the adsorption process, three different types of oil were investigated: medium-chain triglycerides (semi-synthetic oil, paraffin oil (mineral oil and natural oil obtained from the grape seed. The surface tension measurements at the oil/water interface, for chitosan water solutions, indicate a poor surface activity of this biopolymer. Addition of sodium dodecyl sulfate to chitosan solution causes a significant decrease in the interfacial tension for all investigated oils. The results of this study are important for understanding the influence of polymer-surfactant interactions on the properties of the solution and stability of dispersed systems. [Project of the Serbian Ministry of Education, Science and Technological Development, Grant no. III46010

Dispersion stability of a ceramic glaze achieved through ionic surfactant adsorption.

Science.gov (United States)

Panya, Preecha; Arquero, Orn-anong; Franks, George V; Wanless, Erica J

2004-11-01

The adsorption of cetylpyridinium chloride (CPC) and sodium dodecylbenzenesulfonate (SDBS) onto a ceramic glaze mixture composed of limestone, feldspar, quartz, and kaolin has been investigated. Both adsorption isotherms and the average particle zeta potential have been studied in order to understand the suspension stability as a function of pH, ionic strength, and surfactant concentration. The adsorption of small amounts of cationic CPC onto the primarily negatively charged surfaces of the particles at pH 7 and 9 results in strong attraction and flocculation due to hydrophobic interactions. At higher surfactant concentrations a zeta potential of more than +60 mV results from the bilayered adsorbed surfactant, providing stability at salt concentrations dispersion or hydrophobic interactions, the magnitude of the negative zeta potential increases slightly. At pH 9 this increase is enough to promote stability with an average zeta potential of more than -55 mV, whereas at pH 7 the zeta potential is lower at about -45 mV. The stability of suspensions at pH 7 is additionally due to steric repulsion caused by the adsorption of thick layers of neutrally charged Ca(DBS)2 complexes created when the surfactant interacts with dissolved calcium ions from the calcium carbonate component.

Alkylation of isobutane with light olefins: Yields of alkylates for different olefins

Energy Technology Data Exchange (ETDEWEB)

Albright, L.F. [Purdue Univ., West Lafayette, IN (United States); Kranz, K.E.; Masters, K.R. [STRATCO, Inc., Leawood, KS (United States)

1993-12-01

For alkylation of isobutane with C{sub 3}-C{sub 5} olefins using sulfuric acid as the catalyst, the yields of alkylates with different olefins are compared as the operating conditions are changed. The results of recent pilot plant experiments with propylene, C{sub 4} olefins, and C{sub 5} olefins permit such comparisons. The yields expressed as weight of alkylate produced per 100 wt of olefin consumed varied from about 201:100 to 220:100. Weight ratios of the isobutane consumed per olefin consumed vary from about 101:100 to 120:100. differences of yield values are explained by the changes in the overall chemistry. The procedure employed to calculate yields with good accuracy is based on the analysis of the alkylate and the amount of conjunct polymers produced. Based on literature data, yields are also reported for alkylations using HF as the catalyst.

Adsorption behavior of hydrophobin and hydrophobin/surfactant mixtures at the air-water interface.

Science.gov (United States)

Zhang, Xiaoli L; Penfold, Jeffrey; Thomas, Robert K; Tucker, Ian M; Petkov, Jordan T; Bent, Julian; Cox, Andrew; Campbell, Richard A

2011-09-20

The adsorption of the surface-active protein hydrophobin, HFBII, and the competitive adsorption of HFBII with the cationic, anionic, and nonionic surfactants hexadecyltrimethylammonium bromide, CTAB, sodium dodecyl sulfate, SDS, and hexaethylene monododecyl ether, C(12)E(6), has been studied using neutron reflectivity, NR. HFBII adsorbs strongly at the air-water interface to form a dense monolayer ∼30 Å thick, with a mean area per molecule of ∼400 Å(2) and a volume fraction of ∼0.7, for concentrations greater than 0.01 g/L, and the adsorption is independent of the solution pH. In competition with the conventional surfactants CTAB, SDS, and C(12)E(6) at pH 7, the HFBII adsorption totally dominates the surface for surfactant concentrations less than the critical micellar concentration, cmc. Above the cmc of the conventional surfactants, HFBII is displaced by the surfactant (CTAB, SDS, or C(12)E(6)). For C(12)E(6) this displacement is only partial, and some HFBII remains at the surface for concentrations greater than the C(12)E(6) cmc. At low pH (pH 3) the patterns of adsorption for HFBII/SDS and HFBII/C(12)E(6) are different. At concentrations just below the surfactant cmc there is now mixed HFBII/surfactant adsorption for both SDS and C(12)E(6). For the HFBII/SDS mixture the structure of the adsorbed layer is more complex in the region immediately below the SDS cmc, resulting from the HFBII/SDS complex formation at the interface. © 2011 American Chemical Society

Nitric oxide donors attenuate clongenic potential in rat C6 glioma cells treated with alkylating chemotherapeutic agents.

Science.gov (United States)

Yang, Jir-Jei; Yin, Jiu-Haw; Yang, Ding-I

2007-05-11

1,3-Bis(2-chloroethyl)-1-nitrosourea (BCNU) kills tumor cells via multiple actions including alkylation and carbamoylation. Previously, we have reported that formation of S-nitrosoglutathione (GSNO) in glioma cells overexpressing inducible nitric oxide synthase (iNOS) contributed to nitric oxide (NO)-dependent carbamoylating chemoresistance against BCNU. To further characterize the effects of NO on alkylating cytotoxicity, colony formation assay was applied to evaluate the effects of various NO donors on rat C6 glioma cells challenged with alkylating agents. We demonstrate that NO donors including GSNO, diethylamine NONOate (DEA/NO), and sodium nitroprusside (SNP) substantially reduced the extent of colony formation in glioma cells treated with alkylating agents, namely methyl methanesulfonate (MMS), N-methyl-N-nitrosourea (MNU), and N-ethyl-N-nitrosourea (ENU). Without alkylating agents these NO-releasing agents alone had no effects on clongenic potential of rat C6 glioma cells. Among these three NO donors used, the effectiveness in potentiating alkylating cytotoxicity is in the order of "GSNO>DEA/NO>SNP" when applied at the same dosages. GSNO also exerted similar synergistic actions reducing the extents of colony formation when co-administrated with 1,2-bis(methylsulfonyl)-1-(2-chloroethyl)-hydrazine (compound #1), another alkylating agent that mimics the chloroethylating action of BCNU. Together with our previous findings, we propose that NO donors may be used as adjunct chemotherapy with alkylating agents for such malignant brain tumors as glioblastoma multiforme (GBM). In contrast, production of NO as a result of iNOS induction, such as that occurring after surgical resection of brain tumors, may compromise the efficacy of carbamoylating chemotherapy.

Bioaccumulation and toxicity of a cationic surfactant (DODMAC) in sediment dwelling freshwater invertebrates

Energy Technology Data Exchange (ETDEWEB)

Comber, S.D.W. [Atkins Ltd, Chilbrook, Oasis Business Park, Eynsham, Oxford, OX29 4AH (United Kingdom)], E-mail: sean.comber@atkinsglobal.com; Rule, K.L. [Centre for Environmental Sciences, University of Southampton, Southampton SO17 1BJ (United Kingdom); Conrad, A.U. [Scottish Environmental Protection Agency, SEPA Corporate Office, Erskine Court Castle Business Park, Stirling FK9 4TR (United Kingdom); Hoess, S. [ECOSSA, Thierschstrasser 43, 80538 Muenchen (Germany); Webb, S.F. [Procter and Gamble, Temselaan 100, Strombeek-Bever B1853 (Belgium); Marshall, S. [Unilever Colworth, Sharnbrook, Bedford MK44 1LQ (United Kingdom)

2008-05-15

Dimethyldioctadecylammonium chloride (DODMAC, CAS No. 107-64-2) is the principal active component of Di(hydrogenated tallow alkyl) dimethylammonium chloride (DHTDMAC, CAS No. 61789-80-8), a cationic surfactant formerly used principally in laundry fabric softeners. After discharge to water, DODMAC partitions strongly to sediment, therefore the assessment of the effects of DODMAC to benthic organisms is essential in any risk assessment. Chronic toxicity studies were conducted with Lumbriculus variegatus (Oligochaete), Tubifex tubifex (Oligochaete) and Caenorhabditis elegans (Nematode). NOECs were greater than 5738, 1515 and 1351 mg/kg dw, respectively, even for sub-lethal effects. Measurement of the route of uptake of DODMAC by L. variegatus demonstrated the relative importance of uptake via ingestion (86%) compared with direct contact with the sediment and via pore water (14%). The overall tendency of DODMAC to bioaccumulate, however, was low with measured accumulation factors of 0.22 and 0.78 for L. variegatus and T. tubifex, respectively. - The cationic surfactant, DODMAC, exhibits low bioavailability and toxicity to sediment dwelling organisms, with uptake dominated by ingestion.

Bioaccumulation and toxicity of a cationic surfactant (DODMAC) in sediment dwelling freshwater invertebrates

International Nuclear Information System (INIS)

Comber, S.D.W.; Rule, K.L.; Conrad, A.U.; Hoess, S.; Webb, S.F.; Marshall, S.

2008-01-01

Dimethyldioctadecylammonium chloride (DODMAC, CAS No. 107-64-2) is the principal active component of Di(hydrogenated tallow alkyl) dimethylammonium chloride (DHTDMAC, CAS No. 61789-80-8), a cationic surfactant formerly used principally in laundry fabric softeners. After discharge to water, DODMAC partitions strongly to sediment, therefore the assessment of the effects of DODMAC to benthic organisms is essential in any risk assessment. Chronic toxicity studies were conducted with Lumbriculus variegatus (Oligochaete), Tubifex tubifex (Oligochaete) and Caenorhabditis elegans (Nematode). NOECs were greater than 5738, 1515 and 1351 mg/kg dw, respectively, even for sub-lethal effects. Measurement of the route of uptake of DODMAC by L. variegatus demonstrated the relative importance of uptake via ingestion (86%) compared with direct contact with the sediment and via pore water (14%). The overall tendency of DODMAC to bioaccumulate, however, was low with measured accumulation factors of 0.22 and 0.78 for L. variegatus and T. tubifex, respectively. - The cationic surfactant, DODMAC, exhibits low bioavailability and toxicity to sediment dwelling organisms, with uptake dominated by ingestion

Synthetic high-charge organomica: effect of the layer charge and alkyl chain length on the structure of the adsorbed surfactants.

Science.gov (United States)

Pazos, M Carolina; Castro, Miguel A; Orta, M Mar; Pavón, Esperanza; Valencia Rios, Jesús S; Alba, María D

2012-05-15

A family of organomicas was synthesized using synthetic swelling micas with high layer charge (Na(n)Si(8-n)Al(n)Mg(6)F(4)O(20)·XH(2)O, where n = 2, 3, and 4) exchanged with dodecylammonium and octadecylammonium cations. The molecular arrangement of the surfactant was elucidated on the basis on XRD patterns and DTA. The ordering conformation of the surfactant molecules into the interlayer space of micas was investigated by (13)C, (27)Al, and (29)Si MAS NMR. The arrangement of alkylammonium ions in these high-charge synthetic micas depends on the combined effects of the layer charge of the mica and the chain length of the cation. In the organomicas with dodecylammonium, a transition from a parallel layer to a bilayer-paraffin arrangement is observed when the layer charge of the mica increases. However, when octadecylammonium is the interlayer cation, the molecular arrangement of the surfactant was found to follow the bilayer-paraffin model for all values of layer charge. The amount of ordered conformation all-trans is directly proportional of layer charge.

Synthesis and characterization of anionic/nonionic surfactant-interceded iron-doped TiO{sub 2} to enhance sorbent/photo-catalytic properties

Energy Technology Data Exchange (ETDEWEB)

Sharma, Ajit; Lee, Byeong-Kyu, E-mail: bklee@ulsan.ac.kr

2015-09-15

We investigated the synthesis, characterization, and application of surfactant-interceded Fe nanoparticle-doped TiO{sub 2} (TiO{sub 2}/Fe-S1 and TiO{sub 2}/Fe-S2) that were used as adsorbents and photo-catalysts for the removal of As(V) ions from aqueous media. Two types of surfactant (anionic (sodium dodecyl sulfate), S1 and non-ionic (Triton X-100), S2) were used to obtain the separation and mono-dispersion of Fe(III) ions in the reaction solution. The nanocomposites were characterized by Fourier transform infrared (FTIR) spectroscopy, X-ray photoelectron spectroscopy (XPS), UV–vis, scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM/EDX) and elemental mapping analysis before and after As(V) removal. The Langmuir capacities (q{sub e}, mg/g) of the sodium dodecyl sulfate (SDS) and Triton X-100 interceded nanocomposites (TiO{sub 2}/Fe-S1 and TiO{sub 2}/Fe-S2, respectively) for arsenic removal were determined to be 65.79 and 50.76 mg/g, respectively, in aqueous media with As(V) concentration ranges of 0–10 mg/L at pH 6.5. - Highlights: • Fe(III) doped TiO{sub 2} nanocomposite was prepared with surfactant. • Anionic surfactant SDS enhanced the transfer of Fe(III) ions to TiO{sub 2}. • Surfactant-interceded nanocomposite enhanced As(V) removal. • Arsenic removal efficiency was as follows: dark phase>visible phase>UV region.

Grafting C8-C16 alkyl groups altered the self-assembly and curcumin –loading properties of sodium caseinate in water

Directory of Open Access Journals (Sweden)

Yaqiong Zhang

2018-02-01

Full Text Available The data presented here are related to the research article entitled “Synthesis and characterization of alkylated caseinate, and its structure-curcumin loading property relationship in water” (Zhang et al., 2018 [1]. This data article reports the detailed spectra information for 1H NMR, 13C NMR and UPLC-Q-TOF MS of the N-succinimidyl fatty acid esters with various alkyl chain lengths (Cn-NHSs, n = 8, 12, 14 and 16. 1H NMR, 13C NMR and UPLC-Q-TOF MS spectra for C16-NHS are shown as an example. Then the stacked 1H NMR spectra of the obtained alkylated caseinates (Cn-caseinates, n = 8, 12, 14 and 16 are provided. The surface hydrophobicity index (S0 of Cn-caseinates with different substitution degrees (SD of alkyl groups is shown. Additionally, Visual appearances for the formed aqueous dispersions of curcumin-loaded native caseinate (NaCas and Cn-caseinates self-assemblies are shown. X-ray diffraction patterns of curcumin, C16-caseinate, its physical mixture and curcumin-loaded C16-caseinate self-assemblies are examined. The re-dispersibility and short-term storage stability of the curcumin-loaded NaCas and C16-caseinate self-assemblies are also studied. Keywords: Caseinate, Alkylated caseinate, Self-assembly, Curcumin-loading property

The Scarlet Letter of Alkylation: A Mini Review of Selective Alkylating Agents

Science.gov (United States)

Oronsky, Bryan T; Reid, Tony; Knox, Susan J; Scicinski, Jan J

2012-01-01

If there were a stigma scale for chemotherapy, alkylating agents would be ranked at the top of the list. The chemical term alkylation is associated with nonselective toxicity, an association that dates back to the use of nitrogen mustards during World War I as chemical warfare agents. That this stigma persists and extends to compounds that, through selectivity, attempt to “tame” the indiscriminate destructive potential of alkylation is the subject of this review. Selective alkylation, as it is referred to herein, constitutes an extremely nascent and dynamic field in oncology. The pharmacodynamic response to this selective strategy depends on a delicate kinetic balance between specificity and the rate and extent of binding. Three representative compounds are presented: RRx-001, 3-bromopyruvate, and TH-302. The main impetus for the development of these compounds has been the avoidance of the serious complications of traditional alkylating agents; therefore, it is the thesis of this review that they should not experience stigma by association. PMID:22937173

The scarlet letter of alkylation: a mini review of selective alkylating agents.

Science.gov (United States)

Oronsky, Bryan T; Reid, Tony; Knox, Susan J; Scicinski, Jan J

2012-08-01

If there were a stigma scale for chemotherapy, alkylating agents would be ranked at the top of the list. The chemical term alkylation is associated with nonselective toxicity, an association that dates back to the use of nitrogen mustards during World War I as chemical warfare agents. That this stigma persists and extends to compounds that, through selectivity, attempt to "tame" the indiscriminate destructive potential of alkylation is the subject of this review. Selective alkylation, as it is referred to herein, constitutes an extremely nascent and dynamic field in oncology. The pharmacodynamic response to this selective strategy depends on a delicate kinetic balance between specificity and the rate and extent of binding. Three representative compounds are presented: RRx-001, 3-bromopyruvate, and TH-302. The main impetus for the development of these compounds has been the avoidance of the serious complications of traditional alkylating agents; therefore, it is the thesis of this review that they should not experience stigma by association.

A Spectroscopic and Electrochemical Investigation of Interactions of Anticancer Uracil Derivatives with Cationic and Anionic Surfactants

International Nuclear Information System (INIS)

Zafar, F.; Shah, A.; Ahmad, Z.; Siddiq, M.; Ali, S.; Asad Muhammad Khan, A. M.; Rana, U. A.

2015-01-01

Interactions of 5-fluorouracil (5-FU), a commercially available anti-cancer drug and two other possibly anti-cancer actives, 2-thiouracil (2-TU) and 2,4-dithiouracil (DTU), with anionic sodium dodecyl sulphate (SDS) and cationic cetlytrimethyl ammonium bromide (CTAB) surfactants were studied using cyclic voltammetry and UV-Visible spectroscopic techniques. The results from both techniques asserted the formation of complex between the drugs and surfactants. In the pre-micellar concentrations, the binding was mainly due to the interactions between the surfactants monomers (electrostatic) and the drug molecules, while in the post-micellar region, drug was encapsulated within the micelle due to electrostatic as well as hydrophobic interactions. The UV-Visible spectroscopic data of the interaction between 5-fluorouracil and the surfactants exhibited an isobestic point which indicated the presence of equilibrium species in bulk and the micellar phase. Binding constant, partition coefficient between bulk and miceller phase, and the number of drug molecules incorporated per micelle were calculated. (author)

Sono-electroanalysis of copper: enhanced detection and determination in the presence of surfactants.

Science.gov (United States)

Hardcastle, Joanna Lorraine; Hignett, Geraldine; Melville, James L; Compton, Richard G

2002-04-01

Surfactant adsorption has been shown to have a passivating effect on the electrode surface during anodic stripping voltammetric measurements. In the present work the feasibility of sono-anodic stripping analysis for the determination of copper in aqueous media contaminated with surfactant has been studied at an unmodified bare glassy carbon electrode. We illustrate the deleterious effect of three common surfactants, sodium dodecyl sulfate (SDS), dodecyl pyridinium chloride (DPC) and Triton-X 100 (TX-100) on conventional electroanalysis. The analogous sono-electroanalytical response was investigated for each surfactant at ultrasound intensities above and below the cavitation threshold. The enhancement in the stripping signal observed is attributed to the increased mass transport due to acoustic streaming and above the cavitation threshold the intensity of cavitational events is significantly increased leading to shearing of adsorbed surfactant molecules from the surface. As a result accurate analyses for SDS concentrations up to 100 ppm are possible, with analytical signals visible in solutions of SDS and TX-100 of 1000 ppm. Analysis is reported in high concentration of surfactant with use of sono-solvent double extraction. The power of this technique is clearly illustrated by the ability to obtain accurate measurements of copper concentration from starting solutions containing 1000 ppm SDS or TX-100. This was also exemplified by analysis of the low concentration 0.3 microM Cu(II) solution giving a percentage recovery of 94% in the presence of 1000 ppm SDS or TX-100.

Effect of alkyl chain length and temperature on the thermodynamic properties of ionic liquids 1-alkyl-3-methylimidazolium bromide in aqueous and non-aqueous solutions at different temperatures

International Nuclear Information System (INIS)

Sadeghi, Rahmat; Shekaari, Hemayat; Hosseini, Rahim

2009-01-01

The alkyl chain length of 1-alkyl-3-methylimidazolium bromide ([Rmim][Br], R = propyl (C 3 ), hexyl (C 6 ), heptyl (C 7 ), and octyl (C 8 )) was varied to prepare a series of room-temperature ionic liquids (RTILs), and experimental measurements of density and speed of sound at different temperatures ranging from (288.15 to 308.15) K for their aqueous and methanolic solutions in the dilute concentration region (0.01 to 0.30) mol . kg -1 were taken. The values of the compressibilities, expansivity and apparent molar properties for [C n mim][Br] in aqueous and methanolic solutions were determined at the investigated temperatures. The obtained apparent molar volumes and apparent molar isentropic compressibilities were fitted to the Redlich-Mayer and the Pitzer's equations from which the corresponding infinite dilution molar properties were obtained. The values of the infinite dilution molar properties were used to obtain some information about solute-solvent and solute-solute interactions. The thermodynamic properties of investigated ionic liquids in aqueous solutions have been compared with those in methanolic solutions. Also, the comparison between thermodynamic properties of investigated solutions and those of electrolyte solutions, polymer solutions, cationic surfactant solutions and tetraalkylammonium salt solutions have been made

Effect of alkyl chain length and temperature on the thermodynamic properties of ionic liquids 1-alkyl-3-methylimidazolium bromide in aqueous and non-aqueous solutions at different temperatures

Energy Technology Data Exchange (ETDEWEB)

Sadeghi, Rahmat [Department of Chemistry, University of Kurdistan, Sanandaj (Iran, Islamic Republic of)], E-mail: rahsadeghi@yahoo.com; Shekaari, Hemayat [Department of Chemistry, Faculty of Science, University of Mohaghegh Ardabili, Ardabil (Iran, Islamic Republic of); Hosseini, Rahim [Department of Chemistry, University of Kurdistan, Sanandaj (Iran, Islamic Republic of)

2009-02-15

The alkyl chain length of 1-alkyl-3-methylimidazolium bromide ([Rmim][Br], R = propyl (C{sub 3}), hexyl (C{sub 6}), heptyl (C{sub 7}), and octyl (C{sub 8})) was varied to prepare a series of room-temperature ionic liquids (RTILs), and experimental measurements of density and speed of sound at different temperatures ranging from (288.15 to 308.15) K for their aqueous and methanolic solutions in the dilute concentration region (0.01 to 0.30) mol . kg{sup -1} were taken. The values of the compressibilities, expansivity and apparent molar properties for [C{sub n}mim][Br] in aqueous and methanolic solutions were determined at the investigated temperatures. The obtained apparent molar volumes and apparent molar isentropic compressibilities were fitted to the Redlich-Mayer and the Pitzer's equations from which the corresponding infinite dilution molar properties were obtained. The values of the infinite dilution molar properties were used to obtain some information about solute-solvent and solute-solute interactions. The thermodynamic properties of investigated ionic liquids in aqueous solutions have been compared with those in methanolic solutions. Also, the comparison between thermodynamic properties of investigated solutions and those of electrolyte solutions, polymer solutions, cationic surfactant solutions and tetraalkylammonium salt solutions have been made.

Temperature Effect on Micelle Formation: Molecular Thermodynamic Model Revisited.

Science.gov (United States)

Khoshnood, Atefeh; Lukanov, Boris; Firoozabadi, Abbas

2016-03-08

Temperature affects the aggregation of macromolecules such as surfactants, polymers, and proteins in aqueous solutions. The effect on the critical micelle concentration (CMC) is often nonmonotonic. In this work, the effect of temperature on the micellization of ionic and nonionic surfactants in aqueous solutions is studied using a molecular thermodynamic model. Previous studies based on this technique have predicted monotonic behavior for ionic surfactants. Our investigation shows that the choice of tail transfer energy to describe the hydrophobic effect between the surfactant tails and the polar solvent molecules plays a key role in the predicted CMC. We modify the tail transfer energy by taking into account the effect of the surfactant head on the neighboring methylene group. The modification improves the description of the CMC and the predicted micellar size for aqueous solutions of sodium n-alkyl sulfate, dodecyl trimethylammonium bromide (DTAB), and n-alkyl polyoxyethylene. The new tail transfer energy describes the nonmonotonic behavior of CMC versus temperature. In the DTAB-water system, we redefine the head size by including the methylene group, next to the nitrogen, in the head. The change in the head size along with our modified tail transfer energy improves the CMC and aggregation size prediction significantly. Tail transfer is a dominant energy contribution in micellar and microemulsion systems. It also promotes the adsorption of surfactants at fluid-fluid interfaces and affects the formation of adsorbed layer at fluid-solid interfaces. Our proposed modifications have direct applications in the thermodynamic modeling of the effect of temperature on molecular aggregation, both in the bulk and at the interfaces.

EFFECTIVENESS OF WASTE STABILIZATION PONDS IN REMOVAL OF LINEAR ALKYL BENZENE SALFONATE (LAS

Directory of Open Access Journals (Sweden)

Ahmed. M. Abdel-Rahman

2013-06-01

Full Text Available Detergents contain synthetic or organic surface active agents called surfactants, which are derived from petroleum product precursors. They have the common property of lowering the surface tensions of water thus allowing dirt or grease adhered to various articles to be washed off. Linear alkyl benzene sulfonate (LAS is a most commonly used anionic surfactant. Discharge of raw or treated wastewater containing this chemical substance into the environment causes major public health and enviromental problems. In this study, samples were taken from raw wastewater and effluents of treatment ponds of Elzaraby waste stabilization ponds over a period of one year. The treated effluent is either discharged into surface waters or re-used in agricultural irrigation. The samples were analyzed according to the standard methods. The results obtained from the samples taken in different seasons showed that the highest overall removal efficiency of LAS was achieved in summer season (77%, and the least efficiency was observed in Winter season (55%, while the maximum overall efficiency of BOD5 was in summer (88% and minimum efficiency was (73% in winter season. The Dissolved oxygen concentrations along the pond series (DO ranged from 0.18 to 4.8 mg/l.

EFFECTIVENESS OF WASTE STABILIZATION PONDS IN REMOVAL OF LINEAR ALKYL BENZENE SALFONATE (LAS

Directory of Open Access Journals (Sweden)

Ahmed. M. Abdel-Rahman

2013-01-01

Full Text Available Detergents contain synthetic or organic surface active agents called surfactants, which are derived from petroleum product precursors. They have the common property of lowering the surface tensions of water thus allowing dirt or grease adhered to various articles to be washed off. Linear alkyl benzene sulfonate (LAS is a most commonly used anionic surfactant. Discharge of raw or treated wastewater containing this chemical substance into the environment causes major public health and enviromental problems. In this study, samples were taken from raw wastewater and effluents of treatment ponds of Elzaraby waste stabilization ponds over a period of one year. The treated effluent is either discharged into surface waters or re-used in agricultural irrigation. The samples were analyzed according to the standard methods. The results obtained from the samples taken in different seasons showed that the highest overall removal efficiency of LAS was achieved in summer season (77%, and the least efficiency was observed in Winter season (55%, while the maximum overall efficiency of BOD5 was in summer (88% and minimum efficiency was (73% in winter season. The Dissolved oxygen concentrations along the pond series (DO ranged from 0.18 to 4.8 mg/l.

Investigations into surfactant/gas hydrate relationship

Energy Technology Data Exchange (ETDEWEB)

Rogers, Rudy; Zhang, Guochang; Dearman, Jennifer; Woods, Charles [Swalm School of Chemical Engineering, Mississippi State University, Mississippi State, MS 39762 (United States)

2007-03-15

Gas hydrates have unique physical properties portending useful industrial applications of gas storage, gas separation, or water desalination. When gas hydrates were found in the early 1990s to occur naturally and abundantly in seafloors, three other primary interests and concerns emerged: potential new energy source, climate threat from their greenhouse gases, and seafloor instabilities. This paper presents research showing how anionic synthetic surfactants helped develop an industrial gas hydrate storage process for natural gas and how naturally-occurring in-situ anionic biosurfactants influence the formation and placement of gas hydrates in ocean sediments. The catalytic effects, mechanisms, and surface specificities imparted by synthetic surfactants in the gas storage process and imparted by biosurfactants in porous media are discussed. The Bacillus subtilis bacterium that is indigenous to gas hydrate mounds in the Gulf of Mexico was cultured in the laboratory. Its biosurfactant was separated and found to catalyze gas hydrates in porous media. The experiments indicate that seafloor-biosurfactants can be produced rapidly in-situ to achieve threshold concentrations whereby hydrates are promoted. The biosurfactants accumulate and promote hydrate formation on specific mineral surfaces such as sodium montmorillonite. (author)

A comparison study between sodium dodecyl sulfate and sodium dodecyl sulfonate with respect to the thermodynamic properties, micellization, and interaction with poly(ethylene glycol) in aqueous solutions

International Nuclear Information System (INIS)

Sadeghi, Rahmat; Shahabi, Somayyeh

2011-01-01

Graphical abstract: Apparent molar volume against molality: o, ·, and Δ, respectively in water, (1 and 4) wt% PEG solution at 293.15 K; x, Δ, and lozenge, respectively in water, (1 and 4) wt% PEG solution at 313.15 K. Research highlights: → C 12 H 25 SO 3 Na(SDSn) was seen to interact with PEG more weakly than C 12 H 25 SO 4 Na(SDS). → The constraints on molecular mobility of SDS micelles are larger than those of SDSn. → Entropy change on micellization for SDSn is larger than those for SDS. → Micelle formation of SDS is less endothermic and more spontaneous than that of SDSn. → Micelles of SDS have smaller aggregation number than that of SDSn. - Abstract: The density, sound velocity, and conductivity measurements were performed on aqueous solutions of sodium dodecyl sulfate (C 12 H 25 SO 4 Na) or sodium dodecyl sulfonate (C 12 H 25 SO 3 Na) in the absence and presence of poly(ethylene glycol) (PEG) at different temperatures. Changes in the apparent molar volumes and isentropic compressibilities upon micellization were derived using a pseudophase-transition approach and the infinite dilution apparent molar properties of the monomer and micellar form of C 12 H 25 SO 4 Na and C 12 H 25 SO 3 Na were determined. Variations of the critical micelle concentrations (CMCs) of both surfactants in the solutions investigated with temperature were obtained from which thermodynamic parameters of micellization were estimated. It was found that at low temperature the micelle formation process is endothermic and therefore, this process must be entropically driven. However, upon increasing the temperature, the enthalpic factor becomes more significant and, at temperatures higher than 303.15 K the micellization is enthalpy driven. The interactions between C 12 H 25 SO 4 Na/C 12 H 25 SO 3 Na and PEG were studied and it was found that sodium alkyl sulfonates were seen to interact more weakly than their sulfate analogues.

Sodium lauryl ether sulfate (SLES) degradation by nitrate-reducing bacteria

NARCIS (Netherlands)

Silva Paulo, da Ana; Aydin, Rozelin; Dimitrov, Mauricio R.; Vreeling, Harm; Cavaleiro, Ana J.; García-Encina, Pedro A.; Stams, Fons; Plugge, Caroline M.

2017-01-01

The surfactant sodium lauryl ether sulfate (SLES) is widely used in the composition of detergents and frequently ends up in wastewater treatment plants (WWTPs). While aerobic SLES degradation is well studied, little is known about the fate of this compound in anoxic environments, such as

Alkyl and aryl phosphorodiiodidites. Pt. 2

International Nuclear Information System (INIS)

Feshchenko, N.G.; Kostina, V.G.

1976-01-01

Alkyl phosphorodiiodidites are formed in the reactions of alkyl phosphorodichloridites with lithium iodide. They are stable at -60 to -50 0 . When warmed to 20 0 , they disproportionate with conversion into trialkyl phosphites and phosphorus triiodide. The latter also react together and give alkyl iodides, diphosphorus tetraiodide, and a polymer of unestablished structure. Diaryl and dialkyl phosphoriodidites are stable only in solution at low temperatures. They disproportionate in a similar way to aryl and alkyl phosphorodiiodidites. Alkyl phosphorodiiodidites react with iodine with the formation of alkyl iodides and phosphoryl iodide

Rhamnolipids--next generation surfactants?

Science.gov (United States)

Müller, Markus Michael; Kügler, Johannes H; Henkel, Marius; Gerlitzki, Melanie; Hörmann, Barbara; Pöhnlein, Martin; Syldatk, Christoph; Hausmann, Rudolf

2012-12-31

The demand for bio-based processes and materials in the petrochemical industry has significantly increased during the last decade because of the expected running out of petroleum. This trend can be ascribed to three main causes: (1) the increased use of renewable resources for chemical synthesis of already established product classes, (2) the replacement of chemical synthesis of already established product classes by new biotechnological processes based on renewable resources, and (3) the biotechnological production of new molecules with new features or better performances than already established comparable chemically synthesized products. All three approaches are currently being pursued for surfactant production. Biosurfactants are a very promising and interesting substance class because they are based on renewable resources, sustainable, and biologically degradable. Alkyl polyglycosides are chemically synthesized biosurfactants established on the surfactant market. The first microbiological biosurfactants on the market were sophorolipids. Of all currently known biosurfactants, rhamnolipids have the highest potential for becoming the next generation of biosurfactants introduced on the market. Although the metabolic pathways and genetic regulation of biosynthesis are known qualitatively, the quantitative understanding relevant for bioreactor cultivation is still missing. Additionally, high product titers have been exclusively described with vegetable oil as sole carbon source in combination with Pseudomonas aeruginosa strains. Competitive productivity is still out of reach for heterologous hosts or non-pathogenic natural producer strains. Thus, on the one hand there is a need to gain a deeper understanding of the regulation of rhamnolipid production on process and cellular level during bioreactor cultivations. On the other hand, there is a need for metabolizable renewable substrates, which do not compete with food and feed. A sustainable bioeconomy approach should

Effects for rapid conversion from abalone shell to hydroxyapaptite nanosheets by ionic surfactants.

Science.gov (United States)

Zhong, Shengnan; Wen, Zhenliang; Chen, Jingdi; Li, Qian; Shi, Xuetao; Ding, Shinnjyh; Zhang, Qiqing

2017-08-01

Hydroxyapatite (HAP) has been widely used for repairing or substituting human hard tissues. In this paper, two typical ionic surfactants, cation hexadecyltrimethylammonium bromide (CTAB) and anion sodium dodecyl sulfate (SDS), were used for rapid conversion of HAP from abalone shell. From field emission scanning electron microscopy (FESEM), the prepared HAP is flake-like structure. From X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and thermal analysis, these samples contain a small amount of calcium carbonate whose content gradually increases by increasing the surfactants. The results showed that the HAP formed fast on the layer of abalone shell powder with the assistance of CTAB and SDS. Copyright © 2017 Elsevier B.V. All rights reserved.

Effect of surfactant species and electrophoretic medium composition on the electrophoretic behavior of neutral and water-insoluble linear synthetic polymers in nonaqueous capillary zone electrophoresis.

Science.gov (United States)

Fukai, Nao; Kitagawa, Shinya; Ohtani, Hajime

2017-07-01

We have recently demonstrated the separation of neutral and water-insoluble linear synthetic polymers in nonaqueous capillary zone electrophoresis (NACZE) using a cationic surfactant of cetyltrimethylammonium chloride (CTAC). In this study, eight ionic surfactants were investigated for the separation of four synthetic polymers (polystyrene, polymethylmethacrylates, polybutadiene, and polycarbonate); only three surfactants (CTAC, dimethyldioctadecylammonium bromide, and sodium dodecylsulfate) caused their separation. The order of the interaction between the polymers and the surfactants depended on both the surfactant species and the composition of the electrophoretic medium. Their investigation revealed that the separation is majorly affected by the hydrophobic interactions between the polymers and the ionic surfactants. In addition, the electrophoretic behavior of polycarbonate suggested that electrostatic interaction also affects the selectivity of the polymers. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Photoinduced alkylation reactions

Energy Technology Data Exchange (ETDEWEB)

Dondi, D.; Fagnoni, M.; Albini, A.

2002-07-01

Some {alpha}{beta}-unsaturated aldehydes have been alkylated generating alkyl radicals from alcohols and dioxolanes in mixed aqueous-organic solution though photoinduced hydrogen abstraction by disodium benzophenondisulfonate when exposed to solar light (6 to 14 hours for 10 g amounts). (Author) 8 refs.

DNA-directed alkylating ligands as potential antitumor agents: sequence specificity of alkylation by intercalating aniline mustards.

Science.gov (United States)

Prakash, A S; Denny, W A; Gourdie, T A; Valu, K K; Woodgate, P D; Wakelin, L P

1990-10-23

The sequence preferences for alkylation of a series of novel parasubstituted aniline mustards linked to the DNA-intercalating chromophore 9-aminoacridine by an alkyl chain of variable length were studied by using procedures analogous to Maxam-Gilbert reactions. The compounds alkylate DNA at both guanine and adenine sites. For mustards linked to the acridine by a short alkyl chain through a para O- or S-link group, 5'-GT sequences are the most preferred sites at which N7-guanine alkylation occurs. For analogues with longer chain lengths, the preference of 5'-GT sequences diminishes in favor of N7-adenine alkylation at the complementary 5'-AC sequence. Magnesium ions are shown to selectively inhibit alkylation at the N7 of adenine (in the major groove) by these compounds but not the alkylation at the N3 of adenine (in the minor groove) by the antitumor antibiotic CC-1065. Effects of chromophore variation were also studied by using aniline mustards linked to quinazoline and sterically hindered tert-butyl-9-aminoacridine chromophores. The results demonstrate that in this series of DNA-directed mustards the noncovalent interactions of the carrier chromophores with DNA significantly modify the sequence selectivity of alkylation by the mustard. Relationships between the DNA alkylation patterns of these compounds and their biological activities are discussed.

Influence of clay, surfactant and presence of dispersant in the non-aqueous fluids rheology

International Nuclear Information System (INIS)

Gomes, N.L.; Guedes, I.C.; Menezes, R.R.; Campos, L.F.A.; Ferreira, H.S.

2012-01-01

The bentonite clay used as a thickening agent in production of non-aqueous fluids and can not be used without a prior treatment to their organic surfaces become hydrophobic. These treated clays are called organoclays, and are usually obtained by adding, in aqueous solution, a quaternary ammonium salt. This work makes a detailed study of the variables involved in the dispersion of the bentonite clays in organophilization process, as well, the type of clay, type of surfactant and the presence of dispersant. It was observed this study that the process variables involved in the dispersion of the clays and organophilization, observed through characterization, have low influence on the peaks related to interplanar basal distance caused by the incorporation of the surfactant and bentonite clays been influential the type of clay and surfactant and the presence of sodium as dispersant agent, on the rheological properties. (author)

Surfactant phosphatidylcholine metabolism and surfactant function in preterm, ventilated lambs

International Nuclear Information System (INIS)

Jobe, A.H.; Ikegami, M.; Seidner, S.R.; Pettenazzo, A.; Ruffini, L.

1989-01-01

Preterm lambs were delivered at 138 days gestational age and ventilated for periods up to 24 h in order to study surfactant metabolism and surfactant function. The surfactant-saturated phosphatidylcholine pool in the alveolar wash was 13 +/- 4 mumol/kg and did not change from 10 min to 24 h after birth. Trace amounts of labeled natural sheep surfactant were mixed with fetal lung fluid at birth. By 24 h, 80% of the label had become lung-tissue-associated, yet there was no loss of label from phosphatidylcholine in the lungs when calculated as the sum of the lung tissue plus alveolar wash. De novo synthesized phosphatidylcholine was labeled with choline given by intravascular injection at 1 h of age. Labeled phosphatidylcholine accumulated in the lung tissue linearly to 24 h, and the labeled phosphatidylcholine moved through lamellar body to alveolar pools. The turnover time for alveolar phosphatidylcholine was estimated to be about 13 h, indicating an active metabolic pool. A less surface-active surfactant fraction recovered as a supernatant after centrifugation of the alveolar washes at 40,000 x g increased from birth to 10 min of ventilation, but no subsequent changes in the distribution of surfactant phosphatidylcholine in surfactant fractions occurred. The results were consistent with recycling pathway(s) that maintained surface-active surfactant pools in preterm ventilated lambs

Williamson alkylation approach to the synthesis of poly(alkyl vinyl ether) copolymers

International Nuclear Information System (INIS)

Markova, D.; Christova, D.; Velichkova, R.

2008-01-01

A method for synthesis of poly(alkyl vinyl ether-co-vinyl alcohol) copolymers was developed based on the Williamson's alkylation of poly(vinyl acetate) (PVAc) with alkyl iodides. The influence of the alkylating agent and the reaction conditions on the efficiency of the modification reaction was investigated. The copolymers obtained were characterized by means of 1 H NMR and GPC. It was proved that by applying the proposed method copolymers of different composition and properties containing methyl vinyl ether, ethyl vinyl ether as well as n-butyl vinyl ether units could be prepared. Poly(methyl vinyl ether-co-vinyl alcohol)s of high degree of methylation exhibit sharp temperature response at 38-39 deg C in aqueous solution typical of the so-called smart polymers. (authors)

Persurf, a new method to improve surfactant delivery: a study in surfactant depleted rats.

Directory of Open Access Journals (Sweden)

Wolfram Burkhardt

Full Text Available PURPOSE: Exogenous surfactant is not very effective in adults with ARDS, since surfactant does not reach atelectatic alveoli. Perfluorocarbons (PFC can recruit atelectatic areas but do not replace impaired endogenous surfactant. A surfactant-PFC-mixture could combine benefits of both therapies. The aim of the proof-of-principal-study was to produce a PFC-in-surfactant emulsion (Persurf and to test in surfactant depleted Wistar rats whether Persurf achieves I. a more homogenous pulmonary distribution and II. a more homogenous recruitment of alveoli when compared with surfactant or PFC alone. METHODS: Three different PFC were mixed with surfactant and phospholipid concentration in the emulsion was measured. After surfactant depletion, animals either received 30 ml/kg of PF5080, 100 mg/kg of stained (green dye Curosurf™ or 30 ml/kg of Persurf. Lungs were fixated after 1 hour of ventilation and alveolar aeration and surfactant distribution was estimated by a stereological approach. RESULTS: Persurf contained 3 mg/ml phospholipids and was stable for more than 48 hours. Persurf-administration improved oxygenation. Histological evaluation revealed a more homogenous surfactant distribution and alveolar inflation when compared with surfactant treated animals. CONCLUSIONS: In surfactant depleted rats administration of PFC-in-surfactant emulsion leads to a more homogenous distribution and aeration of the lung than surfactant alone.

Optimizing the surfactant for the aqueous processing of LiFePO{sub 4} composite electrodes

Energy Technology Data Exchange (ETDEWEB)

Porcher, W.; Jouanneau, S. [Commissariat a l' Energie Atomique, 38054 Grenoble Cedex 9 (France); Lestriez, B.; Guyomard, D. [Institut des Materiaux Jean Rouxel (IMN), Universite de Nantes, CNRS, 44322 Nantes Cedex 3 (France)

2010-05-01

Aqueous processing would reduce the costs associated with the making of the composite electrode. To achieve the incorporation and the dispersion of the carbon black (CB) conductive agent in aqueous slurries, a surfactant is needed. In this paper, three surfactants are compared, an anionic one, the sodium dodecyle sulphate (SDS), a non-ionic one, the isooctylphenylether of polyoxyethylene called commercially Triton X-100 and a cationic one, the hexadecyltrimethylammonium bromide (CTAB), by using rheology and laser granulometry measurements on electrode slurries on one hand, and SEM observations, porosity and adhesion measurements and electrochemical testing on composite electrodes on the other hand. Ionic surfactants were found to be not suitable because a corrosion of the aluminium current collector occurred. The utilization of Triton X-100 favoured a more homogeneous CB distribution, resulted in a better electronic wiring of the active material particles and higher rate behavior of the electrode. Optimal electrochemical performances are obtained for an optimal surfactant concentration which depends on the BET surface area of the CB powder. (author)

Poly(alkyl acrylate) nonparticles

International Nuclear Information System (INIS)

Kreuter, J.

1985-01-01

This study deals with the preparation of poly(alkyl acrylic) and poly(alkyl cyanocrylic) nanoparticles. Nonoparticles are solid colloidal particles, consisting of macromolecular materials in which drugs or biologically active materials are dissolved, entrapped, and encapsulated, and/or to which the active substance is adsorbed or attached. Poly(alkyl acrylic) nanoparticles are much more slowly biodegradable than poly(alkyl cyanoacrylate) nanoparticles, and are thus more suitable for drug delivery purposes. Poly(methyl methacrylate) is the material of choice for the use of nanoparticles as an adjuvant for vaccines and are produced by emulsifier-free polymerization in aqueous media. The polymerization, which can be initiated with gamma rays or with potassium peroxodisulfate, is described

pH dependent fluorescence switching in salicylideneaniline: ‘off–on–off’ operation controlled by surfactant micelles

Energy Technology Data Exchange (ETDEWEB)

Das, Diganta Kumar, E-mail: digkdas@yahoo.com; Dutta, Kaku

2014-01-15

Salaniline, a condensation product of salicylaldehyde and aniline, shows “off–on” fluorescent behaviour with pH in 1:1 (v/v) CH{sub 3}CN:H{sub 2}O and when 3% (w/v) anionic sodium dodecylsulphate (SDS) surfactant is present. The fluorescent switch behaviour of salaniline is forced to “off–on–off” type by 3% (w/v) neutral triton X-100 (TX-100) and 3% (w/v) cationic cetyltrimethylammonium bromide (CTAB) surfactant. The fluorescent “on” window is observed in the pH range 8.0–12.5 for TX-100 and 7.0–11.0 for CTAB. Different charge nature of the surfactants affects the protonation/deprotonation behaviour of salaniline differently, hence the photoinduced electron transfer (PET) processes and the fluorescent switch behaviour. -- Highlights: • Salicylideneaniline act as pH dependent “off–on” fluorescent switch in 1:1 (v/v) CH{sub 3}CN:H{sub 2}O. • In surfactant micelles TX-100 (neutral) and CTAB (positive) make the fluorescent switch “off–on–off” type while in. • In surfactant micelle SDS (negative) the pH dependent fluorescent switch is “off–on” type.

Permeabilization and recovery of the stratum corneum in vivo: the synergy of photomechanical waves and sodium lauryl sulfate.

Science.gov (United States)

Lee, S; McAuliffe, D J; Kollias, N; Flotte, T J; Doukas, A G

2001-01-01

Photomechanical waves render the stratum corneum permeable and allow macromolecules to diffuse into the epidermis and dermis. The aim of this study was to investigate the combined action of photomechanical waves and sodium lauryl sulfate, an anionic surfactant, for transdermal delivery. A single photomechanical wave was applied to the skin of rats in the presence of sodium lauryl sulfate. The sodium lauryl sulfate solution was removed and aqueous solutions of rhodamine-B dextran (40 kDa molecular weight) were applied to the skin at time points 2, 30, and 60 minutes post-exposure. The presence of rhodamine-B dextran in the skin was measured by fluorescence emission spectroscopy in vivo and fluorescence microscopy of frozen biopsies. The use of sodium lauryl sulfate delayed the recovery of the stratum corneum barrier and extended the time available for the diffusion of dextran through it. The combination of photomechanical waves and surfactants can enhance transdermal drug delivery. Copyright 2001 Wiley-Liss, Inc.

Denaturation of proteins by surfactants studied by the Taylor dispersion analysis.

Directory of Open Access Journals (Sweden)

Aldona Jelińska

Full Text Available We showed that the Taylor Dispersion Analysis (TDA is a fast and easy to use method for the study of denaturation proteins. We applied TDA to study denaturation of β-lactoglobulin, transferrin, and human insulin by anionic surfactant sodium dodecyl sulfate (SDS. A series of measurements at constant protein concentration (for transferrin was 1.9 x 10-5 M, for β- lactoglobulin was 7.6 x 10-5 M, and for insulin was 1.2 x 10-4 M and varying SDS concentrations were carried out in the phosphate-buffered saline (PBS. The structural changes were analyzed based on the diffusion coefficients of the complexes formed at various surfactant concentrations. The concentration of surfactant was varied in the range from 1.2 x 10-4 M to 8.7 x 10-2 M. We determined the minimum concentration of the surfactant necessary to change the native conformation of the proteins. The minimal concentration of SDS for β-lactoglobulin and transferrin was 4.3 x 10-4 M and for insulin 2.3 x 10-4 M. To evaluate the TDA as a novel method for studying denaturation of proteins we also applied other methods i.e. electronic circular dichroism (ECD and dynamic light scattering (DLS to study the same phenomenon. The results obtained using these methods were in agreement with the results from TDA.

Efecto de surfactantes polimerizables en la distribución de tamaño de partícula, pH, viscosidad, contenidos de sólidos y de monómero residual de una resina estireno-butilacrilato Effect of polymerizable surfactants on particle size distribution, pH, viscosity, contents of solids and residual monomer of a styrene-butylacrylate resin

Directory of Open Access Journals (Sweden)

Luis A. Rios

2013-01-01

Full Text Available Se presentan los resultados de la polimerización en emulsión de una resina acrílica estirenada usando surfactantes polimerizables, los cuales presentan ventajas técnicas como baja formación de espuma, alta resistencia de la película al contacto con agua y buena estabilidad en la polimerización. Se evaluó el efecto de estos surfactantes polimerizables en la distribución de tamaños de partícula de la resina; además se determinaron propiedades finales de la resina tales como porcentaje de sólidos, porcentaje de monómero libre, viscosidad y pH. Estos resultados se compararon con los obtenidos usando surfactantes convencionales no polimerizables del tipo alquil fenol etoxilado y alquilarilpoliglicol éter sulfato de sodio. Los resultados indican que que se pueden remplazar totalmente los surfactantes convencionales no polimerizables por los surfactantes poliméricos evaluados sin afectar significativamente las propiedades de la resina, mientras que la sustitución parcial de los surfactantes no polimerizables por los polimerizables induce, en algunos casos, a la formación de partículas con mayor tamaño a las presentes en la muestra estándar.Results on the emulsion polymerization of a styrenated acrylic resin using polymerizable surfactants are presented. These surfactants exhibit low foaming, high film strength upon contact with water and good stability in the polymerization. A comparison was made with results for conventional non-polymerizable alkyl aryl polyglycol ether sulphate, sodium salt and nonylphenolethoxylate surfactants. The effect of these polymerizable surfactants on the particle size distribution of the resin was evaluated; in addition to determining the final properties of the resin such as solids content, free monomer content, viscosity and pH. It is feasible to totally replace non-polymerizable surfactants by the polymerizable surfactants evaluated without affecting significantly the properties of the resin, while

[Effect of 60Co gamma-irradiation on dilute aqueous solutions of surfactants].

Science.gov (United States)

Sawai, T; Shimokowa, T; Miki, Y; Oseko, K; Sawai, T

1978-01-01

Present work deals with the effects of gamma irradiation from 60Co gamma-ray source upon aqueous solutions of three kinds of surfactants. When dilute aqueous solutions of sodium dodecyl sulfate (SDS, anionic), cethyl trimethyl ammonium chloride (CTAC, cationic), and polyoxyethylene lauryl ether (POE, non-ionic) were irradiated with gamma-rays at a room remperature, the residual concentration, products, surface tension, and forming power were examined by colorimetric method, IR spectrophotometric method, gaschromatography, Ross-Miles method, and Traube's stalagnometer etc.. These surfactants were decomposed by the irradiation and thus the surface tension increased and the forming power, on the contrary, decreased with dose. Radiation chemical yields (G-value) of the degradation were about 1 for the solutions of SDS and CTAC, and about 0.3 for the POE solution. From the experimental results, it was found that following chemical reactions seem to occur followed by the radiolysis of water; a) bond cleavage of ester for SDS, of CN for CTAC, and of oxyethylene for POE, b) hydrogen abstraction from the surfactants, c) production of CO bond in the presence of dissolved oxygen.

Safety assessment of decyl glucoside and other alkyl glucosides as used in cosmetics.

Science.gov (United States)

Fiume, Monice M; Heldreth, Bart; Bergfeld, Wilma F; Belsito, Donald V; Hill, Ronald A; Klaassen, Curtis D; Liebler, Daniel; Marks, James G; Shank, Ronald C; Slaga, Thomas J; Snyder, Paul W; Andersen, F Alan

2013-01-01

The Cosmetic Ingredient Review (CIR) Expert Panel assessed the safety of 19 alkyl glucosides as used in cosmetics and concluded that these ingredients are safe in the present practices of use and concentration when formulated to be nonirritating. Most of these ingredients function as surfactants in cosmetics, but some have additional functions as skin-conditioning agents, hair-conditioning agents, or emulsion stabilizers. The Panel reviewed the available animal and clinical data on these ingredients. Since glucoside hydrolases in human skin are likely to break down these ingredients to release their respective fatty acids and glucose, the Panel also reviewed CIR reports on the safety of fatty alcohols and were able to extrapolate data from those previous reports to support safety.

Grafting C8-C16 alkyl groups altered the self-assembly and curcumin -loading properties of sodium caseinate in water.

Science.gov (United States)

Zhang, Yaqiong; Yang, Puyu; Yao, Fangyi; Liu, Jie; Yu, Liangli Lucy

2018-02-01

The data presented here are related to the research article entitled "Synthesis and characterization of alkylated caseinate, and its structure-curcumin loading property relationship in water" (Zhang et al., 2018) [1]. This data article reports the detailed spectra information for 1 H NMR, 13 C NMR and UPLC-Q-TOF MS of the N-succinimidyl fatty acid esters with various alkyl chain lengths (Cn-NHSs, n = 8, 12, 14 and 16). 1 H NMR, 13 C NMR and UPLC-Q-TOF MS spectra for C16-NHS are shown as an example. Then the stacked 1 H NMR spectra of the obtained alkylated caseinates (Cn-caseinates, n = 8, 12, 14 and 16) are provided. The surface hydrophobicity index (S 0 ) of Cn-caseinates with different substitution degrees (SD) of alkyl groups is shown. Additionally, Visual appearances for the formed aqueous dispersions of curcumin-loaded native caseinate (NaCas) and Cn-caseinates self-assemblies are shown. X-ray diffraction patterns of curcumin, C16-caseinate, its physical mixture and curcumin-loaded C16-caseinate self-assemblies are examined. The re-dispersibility and short-term storage stability of the curcumin-loaded NaCas and C16-caseinate self-assemblies are also studied.

Characteristics and environmental fate of the anionic surfactant sodium lauryl ether sulphate (SLES) used as the main component in foaming agents for mechanized tunnelling

International Nuclear Information System (INIS)

Barra Caracciolo, Anna; Cardoni, Martina; Pescatore, Tanita; Patrolecco, Luisa

2017-01-01

The anionic surfactant sodium lauryl ether sulphate (SLES) is the main component of most commercial products used for soil conditioning in the excavation industry, in particular as lubricants for mechanized tunnelling. Its use during the excavation processes can result in either the subsequent possible re-use of the huge amount of soil debris as by-products (e.g. land covering) or its discharge as waste. Currently, there are neither SLES soil threshold limits in European legislation, nor comprehensive studies on the environmental risk for soil ecosystems in these exposure scenarios. In this context, the present paper reviews the available data on the intrinsic characteristics of persistence and the ecotoxicological effects of the anionic surfactant SLES. Although SLES is generally reported to be biodegradable in standard tests, with degradation rates between 7 h and 30 days, depending on the initial conditions, data on its biodegradation in environmental studies are quite scarce. Consequently, assessing SLES biodegradation rates in field conditions is crucial for evaluating if in residual concentrations (typically in the range 40–500 mg/kg in excavated soils) it can or not be a potential hazard for terrestrial and water organisms. Laboratory ecotoxicological tests pointed out detrimental effects of SLES for aquatic organisms, while data on the terrestrial species are rather poor so far and further studies at the expected environmental concentrations are necessary. Finally, the review reports the main analytical methods available for detecting anionic surfactants in solid matrices and the future research needed to improve knowledge on the possible environmental risks posed by the use of SLES in foaming agents for mechanized tunnelling. - Highlights: • Tons of excavated soil containing SLES are reused posing an environmental risk. • SLES can have detrimental effects on aquatic organisms exposed in lab test. • There is a need to improve knowledge on SLES

Effect of Al_2O_3 nanolubrication with Sodium Dodecylbenzene Sulfonate (SDBS) on surface roughness and tool wear under MQL during turning of Ti-6AL-4T

International Nuclear Information System (INIS)

Ali, M A M; Khalil, A N M; Azmi, A I

2016-01-01

The application of coolant reduces the friction and heat generation, which affect the surface finish and tool life, during machining. Recently, nanolubricant opens a new ways of coolant strategy in machining operation. It is well known that suspended nanoparticles without surfactant in base oil tend to agglomerate after a period of time. This paper presents the effects of AEO_3 nanolubricant with surfactant, Sodium Dodecylbenzene Sulfonate (SDBS) on surface roughness and tool wear during turning of titanium alloy, Ti-6AL-4T. The comparison of different coolant strategies, dry cutting, flooding, minimum quantity lubricant (MQL), nanolubricant with and without surfactant are also presented. The results showed that Al_2O_3 nanolubricant with surfactant, Sodium Dodecylbenzene Sulfonate (SDBS) under MQL exhibits low surface roughness and tool wear rate compared to others. This proved that the addition of surfactant not only improved nanolubricant stability but also machining performance. (paper)

Effect of surfactant amount on the morphology and magnetic properties of monodisperse ZnFe{sub 2}O{sub 4} nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Zhao, Haitao, E-mail: zht95711lunwen@163.com; Liu, Ruiping; Zhang, Qiang; Wang, Qiao

2016-03-15

Graphical abstract: Polyol process to monodisperse ZnFe{sub 2}O{sub 4} nanoparticles. - Highlights: • An one-step, facile and inexpensive synthetic route to monodisperse ZnFe{sub 2}O{sub 4} nanoparticles is described. • The sodium citrate stabilized ZnFe{sub 2}O{sub 4} nanoparticles with a diameter in the 5–8 nm size range can be easily dispersed in water. • The synthesis is very robust in terms of variations of experimental parameters. • ZnFe{sub 2}O{sub 4} nanoparticles present ferrimagnetic behavior at room temperature with a small hysteresis. - Abstract: The spinel ZnFe{sub 2}O{sub 4} ferrites with sodium citrate as a surfactant were fabricated by polyol process. The effect of surfactant amount on the structure, morphology and magnetic properties of ZnFe{sub 2}O{sub 4} ferrites were investigated by X-ray diffraction(XRD), transmission electron microscope (TEM), thermogravimetric and differential scanning calorimetry (TG–DSC) and vibrating sample magnetometry (VSM), respectively. The results indicate that the structure of ZnFe{sub 2}O{sub 4} ferrites is a pure cubic spinel structure with a particle size of 5–8 nm. The dispersion of the synthesized ZnFe{sub 2}O{sub 4} is enhanced when the mole ratio of Fe(acac){sub 3} to sodium citrate decreases. The synthesized particles present ferrimagnetic behavior with a small hysteresis at room temperature. The increase of surfactant amount conversely leads to the decrease in the saturation magnetization value (Ms) especially when the mole ratio of Fe(acac){sub 3} to sodium citrate decreases to 8:3. Its Ms value is drastically reduced to 18.97 emu/g.

Radiometric determination of anionic surfactants by two-phase titration method with the use of sup(131)I-Rose Bengal as indicator

International Nuclear Information System (INIS)

Lengyel, J.; Krtil, J.

1986-01-01

A radiometric variant of the two-phase titration method for the determination of anionic surfactants of nonsoapy type is described. The method is based on the titration of an anionic surfactant with Septonex in alkaline medium in the presence of sup(131)I-Rose Bengal (sup(131)I-RB). The ion associates are extracted into chloroform. The equivalence point is determined graphically from the activity of sup(131)I-RB-Septonex associate, which is formed after the consumption of the anionic surfactant and passes into the organic phase. The influence of sup(131)I-RB amount, pH of the titrated medium and of soap on the precision of anionic surfactant determination was studied. The detection limit is 2.88 μg sodium n-dodecylsulfate in 10 ml of sample. (author)

Evaluation of soy-based surface active copolymers as surfactant ingredients in model shampoo formulations.

Science.gov (United States)

Popadyuk, A; Kalita, H; Chisholm, B J; Voronov, A

2014-12-01

A new non-toxic soybean oil-based polymeric surfactant (SBPS) for personal-care products was developed and extensively characterized, including an evaluation of the polymeric surfactant performance in model shampoo formulations. To experimentally assure applicability of the soy-based macromolecules in shampoos, either in combination with common anionic surfactants (in this study, sodium lauryl sulfate, SLS) or as a single surface-active ingredient, the testing of SBPS physicochemical properties, performance and visual assessment of SBPS-based model shampoos was carried out. The results obtained, including foaming and cleaning ability of model formulations, were compared to those with only SLS as a surfactant as well as to SLS-free shampoos. Overall, the results show that the presence of SBPS improves cleaning, foaming, and conditioning of model formulations. SBPS-based formulations meet major requirements of multifunctional shampoos - mild detergency, foaming, good conditioning, and aesthetic appeal, which are comparable to commercially available shampoos. In addition, examination of SBPS/SLS mixtures in model shampoos showed that the presence of the SBPS enables the concentration of SLS to be significantly reduced without sacrificing shampoo performance. © 2014 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

Improved microbial growth inhibition activity of bio-surfactant induced Ag–TiO{sub 2} core shell nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Nithyadevi, D. [Department of Nanoscience and Technology, Bharathiar University, Coimbatore 641 046 (India); Kumar, P. Suresh [Thin Film and Nanomaterials Laboratory, Department of Physics, Bharathiar University, Coimbatore 641 046 (India); Mangalaraj, D., E-mail: dmraj800@yahoo.com [Department of Nanoscience and Technology, Bharathiar University, Coimbatore 641 046 (India); Ponpandian, N.; Viswanathan, C. [Department of Nanoscience and Technology, Bharathiar University, Coimbatore 641 046 (India); Meena, P. [Department of Physics, PSGR Krishnammal college for women, Coimbatore 641 004 (India)

2015-02-01

Graphical abstract: - Highlights: • TiO{sub 2} nanoparticles were synthesized by hydrolysis process and Ag nanoparticles were prepared by using hydrazine reduction method. • Ag–TiO{sub 2} core shell nanoparticles were synthesized by reverse micelle method. • Coatings of TiO{sub 2} shell leads to decrease the usage of silver particles and also it reduces the release of silver ions from the matrix. • Optimum ratio of TiO{sub 2} particles: Ag atoms are needed for better antibacterial activity. • Sodium alginate (Bio-copolymer) induced core shell nanoparticles results 100% cell growth inhibition toward Staphylococcus aureus. - Abstract: Surfactant induced silver–titanium dioxide core shell nanoparticles within the size range of 10–50 nm were applied in the antibacterial agent to inhibit the growth of bacterial cells. The single crystalline silver was located in the core part of the composite powder and the titanium dioxide components were uniformly distributed in the shell part. HRTEM and XRD results indicated that silver was completely covered by titanium dioxide and its crystal structure was not affected after being coated by titanium dioxide. The effect of silver–titanium dioxide nanoparticles in the inhibition of bacterial cell growth was studied by means of disk diffusion method. The inhibition zone results reveal that sodium alginate induced silver–titanium dioxide nanoparticles exhibit 100% more antibacterial activity than that with cetyltrimethylbromide or without surfactant. UV–vis spectroscopic analysis showed a large concentration of silver was rapidly released into phosphate buffer solution (PBS) within a period of 1 day, with a much smaller concentration being released after this 1-day period. It was concluded that sodium alginate induced silver–titanium dioxide core shell nanoparticles could enhance long term cell growth inhibition in comparison with cetyltrimethylbromide or without surfactant. The surfactant mediated core shell

Adsorption of ionic surfactants at microscopic air-water interfaces using the micropipette interfacial area-expansion method

DEFF Research Database (Denmark)

Kinoshita, Koji; Parra, Elisa; Needham, David

2017-01-01

The dynamic adsorption of ionic surfactants at air-water interfaces have been less-well studied than that of the simpler non-ionics since experimental limitations on dynamic surface tension (DST) measurements create inconsistencies in their kinetic analysis. Using our newly designed "Micropipette...... interfacial area-expansion method", we have measured and evaluated both equilibrium and dynamic adsorption of a well-known anionic surfactant, sodium dodecyl sulphate (SDS), in the absence or presence of 100mM NaCl. Our focus was to determine if and to what extent the inclusion of a new correction parameter...... for the "ideal ionic activity", A±i, can renormalize both equilibrium and dynamic surface tension measurements and provide better estimates of the diffusion coefficient of ionic surfactants in aqueous media obtained from electroneutral models, namely extended Frumkin isotherm and Ward-Tordai adsorption models...

Preparation, Characterization and Performance Studies of Active PVDF Ultrafiltration-Surfactants Membranes Containing PVP as Additive

International Nuclear Information System (INIS)

Nur Izzah Md Fadilah; Abdul Rahman Hassan

2016-01-01

The role of surfactants in the formation of active Poly(vinylidene fluoride) (PVDF) ultrafiltration (AUF) membranes was studied. The effect combination of surfactants that are Sodium dodecyl sulfate (SDS)/ Tween 80 and Tween 80/ Triton X-100 formulations on performance and morphological structures were investigated for the first time. The influence of surfactants blends on the membrane pores was also examined. Experimental data showed that combination of Tween 80/ Triton X-100 give the highest BSA permeation flux with a value of 285.51 Lm -2 h -1 . With combination of SDS/ Tween 80, the AUF membrane showed the highest protein rejection up to 93 % and 79 % for Bovine Serum Albumin (BSA) and Egg Albumin (EA), respectively. Moreover, membranes characterization demonstrated that the addition of SDS/ Tween 80 and Tween 80/ Triton X-100 were found to affect the performance, surface morphologies and membrane pores of AUF PVDF membranes. (author)

Adsorption kinetics of surfactants on activated carbon

Science.gov (United States)

Arnelli; Aditama, WP; Fikriani, Z.; Astuti, Y.

2018-04-01

A study on the adsorption of both cationic and anionic surfactants using activated carbon as well as the investigation of the adsorption isotherms and adsorption kinetics has been conducted. The results showed that the adsorption of sodium lauryl sulfate (SLS) by activated carbon was Langmuir’s adsorption isotherm while its adsorption kinetics showed pseudo-second order with an adsorption rate constant of 2.23 x 103 g mg-1 hour-1. Meanwhile, the adsorption of HDTMA-Br by activated carbon showed that the isotherm adsorption tended to follow Freundlich’s isotherm and was pseudo-second order with an adsorption rate constant of 89.39 g mg-1 hour-1.

Effect of chemical structure on the cloud point of some new non-ionic surfactants based on bisphenol in relation to their surface active properties

Directory of Open Access Journals (Sweden)

A.M. Al-Sabagh

2011-06-01

Full Text Available A series of non-ionic surfactants were prepared from bisphenol derived from acetone (A, acetophenone (AC and cyclohexanone (CH. The prepared bisphenols were ethoxylated at different degrees of ethylene oxide (27, 35, 43. The ethoxylated bisphenols were non-esterified by fatty acids; decanoic, lauric, myristic, palmitic, stearic, oleic, linoloic and linolinic. Some surface active properties for these surfactants were measured and calculated such as, surface tension [γ], critical micelle concentration [CMC], minimum area per molecule [Amin], surface excess [Cmax], free energy of micellization and adsorption [ΔGmic] and [ΔGads]. At a certain temperature, the cloud point was measured for these surfactants. From the obtained data it was found that; the cloud point is very sensitive to the increase of the alkyl chain length, content of ethylene oxide and degree of unsaturation. The core of bisphenol affected the cloud point sharply and they are ranked regarding bisphenol structure as BA > BCH > BAC. By inspection of the surface active properties of these surfactants, a good relation was obtained with their cloud points. The data were discussed on the light of their chemical structures.

Effect of a Benzalkonium Chloride Surfactant-Sodium Hypochlorite Combination on Elimination of Enterococcus faecalis.

Science.gov (United States)

Baron, Aleksandr; Lindsey, Kimberly; Sidow, Stephanie J; Dickinson, Douglas; Chuang, Augustine; McPherson, James C

2016-01-01

The purpose of this investigation was to determine the effect of a sodium hypochlorite-surfactant combination on the removal of Enterococcus faecalis from infected teeth. Sixty-four extracted human single canal anterior teeth were prepared with rotary instrumentation and sterilized. Teeth were divided into 4 groups, N = 16. Three experimental groups were inoculated with E. faecalis and cultured for 21 days before use: positive control group, no irrigation; NaOCl group, irrigated with 5 mL 6% NaOCl; and NaOCl/BAK group, irrigated with 5 mL 6% NaOCl/0.008% benzalkonium chloride (BAK). The negative control group received medium only and no inoculate. Paper point sampling of the canals was obtained before irrigation (S1) for all 4 groups and for 2 groups after irrigation (S2) to determine remaining colony-forming units. After sampling, all teeth were split in half and evaluated for bacterial viability colony-forming units and penetration of dentinal tubules by using fluorescent vital dye staining and confocal laser scanning microscopy. Comparison of pre-irrigation and post-irrigation paper point samples from the 2 irrigated groups showed a significant reduction in bacterial canal load (P < .001, Kruskal-Wallis), with a significantly lower load in the NaOCl/BAK group than in the NaOCl group (P = .001, Mann-Whitney U test); 68.8% of the NaOCl/BAK samples gave no recoverable counts. In contrast, no significant difference between these groups was found for counts recovered from dentin. Confocal laser scanning microscopy showed no differences in tubule penetration. The addition of BAK to NaOCl significantly reduced the number of remaining bacteria within the canal after irrigation compared with NaOCl alone. Published by Elsevier Inc.

Tensiometric, fluorescence and 1H NMR study of mixed micellization of non-steroidal anti-inflammatory drug sodium salt of ibuprofen in the presence of non-ionic surfactant in aqueous/urea solutions

International Nuclear Information System (INIS)

Rub, Malik Abdul; Khan, Farah; Sheikh, Mohmad Shafi; Azum, Naved; Asiri, Abdullah M.

2016-01-01

Highlights: • Interaction between (IBF + TX-100) mixtures has been investigated. • (IBF + TX-100) mixtures exhibit synergistic behavior. • Urea increases the surface charge of the micelles resulting halt of the micelles formation. • N agg , K sv and dielectric constant of mixed systems have also been evaluated. • 1 H NMR data suggested that IBF and TX-100 interacts through hydrophobic as well as hydrophillic interaction. - Abstract: The desirable surface/bulk properties for specific applications of drug sodium salt of ibuprofen (IBF) and Triton X-100 (TX-100) can be achieved by adjusting mainly the composition of these systems. The interactions of anionic drug IBF with non-ionic surfactant TX-100 micelles have been investigated using tensiometry, fluorometry and 1 H NMR in aqueous as well in 250 mmol⋅kg −1 urea solutions. Different theoretical models like Clint, Rubingh, and Rosen, etc. were utilized to get information about the nature of interaction between these two in bulk and at the interface. These models disclose that the non-ideal behavior with attractive interaction in bulk and at the interface exists. The steady-state fluorescence quenching study was employed to evaluate micelle aggregation numbers (N agg ), which signify the involvement of surfactant was forever higher compared to IBF. Stern–Volmer binding constants (K sv ), micropolarity (I 1 /I 3 ) and dielectric constant (D exp ) of the mixtures are also obtained using fluorescence method. By the addition of urea raise in the surface charge of the micelles was observed followed by halt of the micellization of drug and surfactant as well as their mixture, therefore cmc values increases followed by decrease in aggregation number. The 1 H NMR resonance intensity variations were paralleled by upfield shifts in the resonance frequencies, due to an increased shielding of IBF happening from closeness of the non-ionic TX-100 surfactant.

CLONING AND SEQUENCING OF PSEUDOMONAS GENES DETERMINING SODIUM DODECYL-SULFATE BIODEGRADATION

NARCIS (Netherlands)

DAVISON, J; BRUNEL, F; PHANOPOULOS, A; PROZZI, D; TERPSTRA, P

1992-01-01

The nucleotide sequences of two genes involved in sodium dodecyl sulfate (SDS) degradation, by Pseudomonas, have been determined. One of these, sdsA, codes for an alkyl sulfatase (58 957 Da) and has similarity (31.8% identity over a 201-amino acid stretch) to the N terminus of a predicted protein of

Stabilization of cadmium electrode properties when introducing surfactants

International Nuclear Information System (INIS)

Alekseeva, M.E.; Mansurov, F.Kh.; Nikol'skij, V.A.

1995-01-01

The results of tests of both separate cadmium electrodes and silver-cadmium accumulators, depending on introduction of surfactants (polyethylene oxide - PO - and its derivatives), have been considered. The influence of PO on the course of electrochemical reaction on cadmium is pronounced in facilitation of anodic process. In case of PO introduction in the amount of 1 % instead of sodium lignosulfonate (2 %) into accumulators with silver-cadmium electrodes, the electrode potential is stabilized, while the accumulator capacity increases. The time period of the accumulation maintenance in the charged state increases 2-3 fold (1-1,5 years). 5 refs.; 4 figs.; 2 tabs

Embryotoxicity induced by alkylating agents. Some methodological aspects of DNA alkylation studies in murine embryos using ethylmethanesulfonate.

Science.gov (United States)

Platzek, T; Bochert, G; Rahm, U; Neubert, D

1987-05-01

Synthesis and spectroscopic analysis of some alkylated DNA purine bases are described. HPLC separation methods are developed for the determination of DNA alkylation rates in mammalian embryonic tissues. Following treatment of pregnant mice with the ethylating agent ethylmethanesulfonate (EMS), an appreciable amount of alkylation (ethylation and methylation) was found in the nuclear DNA of the embryos during organogenesis. The results are discussed in context of our thesis that a certain amount of DNA alkylation in the embryos is correlated to the teratogenic potential of alkylating agents.

Synthesis of Mixed Carbonates via a Three-Component Coupling of Alcohols, CO2, and Alkyl Halides in the Presence of K2CO3 and Tetrabutylammonium Iodide

OpenAIRE

Yu-Mei Shen; Min Shi

2002-01-01

Various mixed carbonates can be conveniently prepared in good yields using the corresponding alcohols, alkyl halides under CO2 atmosphere in the presence of potassium carbonate or sodium carbonate and tetrabutylammonium iodide.

A solid phase extraction-ion chromatography with conductivity detection procedure for determining cationic surfactants in surface water samples.

Science.gov (United States)

Olkowska, Ewa; Polkowska, Żaneta; Namieśnik, Jacek

2013-11-15

A new analytical procedure for the simultaneous determination of individual cationic surfactants (alkyl benzyl dimethyl ammonium chlorides) in surface water samples has been developed. We describe this methodology for the first time: it involves the application of solid phase extraction (SPE-for sample preparation) coupled with ion chromatography-conductivity detection (IC-CD-for the final determination). Mean recoveries of analytes between 79% and 93%, and overall method quantification limits in the range from 0.0018 to 0.038 μg/mL for surface water and CRM samples were achieved. The methodology was applied to the determination of individual alkyl benzyl quaternary ammonium compounds in environmental samples (reservoir water) and enables their presence in such types of waters to be confirmed. In addition, it is a simpler, less time-consuming, labour-intensive, avoiding use of toxic chloroform and significantly less expensive methodology than previously described approaches (liquid-liquid extraction coupled with liquid chromatography-mass spectrometry). Copyright © 2013 Elsevier B.V. All rights reserved.

Preparation of Barley Storage Protein, Hordein, for Analytical Sodium Dodecyl Sulfate-Polyacrylamide Gel Electrophoresis

DEFF Research Database (Denmark)

Doll, Hans; Andersen, Bente

1981-01-01

The extraction, reduction, and alkylation of barley hordein for routine electrophoresis in sodium dodecyl sulfate-polyacrylamide gels were studied to set up a simple preparation procedure giving well-resolved bands in the electrophoresis gel. Hordein was extracted from single crushed seeds or flour...... by aqueous 50% propan-2-ol containing a Tris-borate buffer, pH 8.6. The presence of the buffer facilitates the consecutive complete reduction of the extracted protein in the alcohol. Reduction and alkylation in the buffer containing propan-2-ol give sharper bands in the electrophoresis than reduction...

Thioimidazolium Ionic Liquids as Tunable Alkylating Agents.

Science.gov (United States)

Guterman, Ryan; Miao, Han; Antonietti, Markus

2018-01-19

Alkylating ionic liquids based on the thioimidazolium structure combine the conventional properties of ionic liquids, including low melting point and nonvolatility, with the alkylating function. Alkyl transfer occurs exclusively from the S-alkyl position, thus allowing for easy derivatization of the structure without compromising specificity. We apply this feature to tune the electrophilicty of the cation to profoundly affect the reactivity of these alkylating ionic liquids, with a caffeine-derived compound possessing the highest reactivity. Anion choice was found to affect reaction rates, with iodide anions assisting in the alkylation reaction through a "shuttling" process. The ability to tune the properties of the alkylating agent using the toolbox of ionic liquid chemistry highlights the modular nature of these compounds as a platform for alkylating agent design and integration in to future systems.

Influence of synthetic surfactants on the uptake of Pd, Cd and Pb by the marine macroalga, Ulva lactuca

Energy Technology Data Exchange (ETDEWEB)

Masakorala, Kanaji [School of Earth, Ocean and Environmental Sciences, University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom); Turner, Andrew [School of Earth, Ocean and Environmental Sciences, University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom)], E-mail: aturner@plymouth.ac.uk; Brown, Murray T. [School of Biological Sciences, University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom)

2008-12-15

Uptake of Pd, Cd and Pb by the marine macroalga, Ulva lactuca, has been studied in the presence of an anionic (sodium dodecyl sulphate, SDS), cationic (hexadecyltrimethylammonium bromide; HDTMA) and non-ionic (Triton X-100; TX) surfactant. Compared with the surfactant-free system, metal sorption was reduced in the presence of SDS or TX. Neither surfactant, however, had any measurable impact on cell membrane permeability, determined by leakage of dissolved free amino acids (DFAA), or on metal internalisation. We attribute these observations to the stabilisation of aqueous Cd and Pb by SDS and the shielding of otherwise amenable sorption sites by TX. Presence of HDTMA resulted in a reduction in the extent of both sorption and internalisation of all metals and a significant increase in the leakage of DFAA. Thus, by enhancing membrane permeability, HDTMA exerts the greatest influence on metal behaviour in the presence of U. lactuca. - Synthetic surfactants exert a significant impact on the uptake and internalisation of metals by a marine macroalga.

Influence of synthetic surfactants on the uptake of Pd, Cd and Pb by the marine macroalga, Ulva lactuca

International Nuclear Information System (INIS)

Masakorala, Kanaji; Turner, Andrew; Brown, Murray T.

2008-01-01

Uptake of Pd, Cd and Pb by the marine macroalga, Ulva lactuca, has been studied in the presence of an anionic (sodium dodecyl sulphate, SDS), cationic (hexadecyltrimethylammonium bromide; HDTMA) and non-ionic (Triton X-100; TX) surfactant. Compared with the surfactant-free system, metal sorption was reduced in the presence of SDS or TX. Neither surfactant, however, had any measurable impact on cell membrane permeability, determined by leakage of dissolved free amino acids (DFAA), or on metal internalisation. We attribute these observations to the stabilisation of aqueous Cd and Pb by SDS and the shielding of otherwise amenable sorption sites by TX. Presence of HDTMA resulted in a reduction in the extent of both sorption and internalisation of all metals and a significant increase in the leakage of DFAA. Thus, by enhancing membrane permeability, HDTMA exerts the greatest influence on metal behaviour in the presence of U. lactuca. - Synthetic surfactants exert a significant impact on the uptake and internalisation of metals by a marine macroalga

Release of surfactant cargo from interfacially-active halloysite clay nanotubes for oil spill remediation.

Science.gov (United States)

Owoseni, Olasehinde; Nyankson, Emmanuel; Zhang, Yueheng; Adams, Samantha J; He, Jibao; McPherson, Gary L; Bose, Arijit; Gupta, Ram B; John, Vijay T

2014-11-18

Naturally occurring halloysite clay nanotubes are effective in stabilizing oil-in-water emulsions and can serve as interfacially-active vehicles for delivering oil spill treating agents. Halloysite nanotubes adsorb at the oil-water interface and stabilize oil-in-water emulsions that are stable for months. Cryo-scanning electron microscopy (Cryo-SEM) imaging of the oil-in-water emulsions shows that these nanotubes assemble in a side-on orientation at the oil-water interface and form networks on the interface through end-to-end linkages. For application in the treatment of marine oil spills, halloysite nanotubes were successfully loaded with surfactants and utilized as an interfacially-active vehicle for the delivery of surfactant cargo. The adsorption of surfactant molecules at the interface serves to lower the interfacial tension while the adsorption of particles provides a steric barrier to drop coalescence. Pendant drop tensiometry was used to characterize the dynamic reduction in interfacial tension resulting from the release of dioctyl sulfosuccinate sodium salt (DOSS) from halloysite nanotubes. At appropriate surfactant compositions and loadings in halloysite nanotubes, the crude oil-saline water interfacial tension is effectively lowered to levels appropriate for the dispersion of oil. This work indicates a novel concept of integrating particle stabilization of emulsions together with the release of chemical surfactants from the particles for the development of an alternative, cheaper, and environmentally-benign technology for oil spill remediation.

Stress responses of duckweed (Lemna minor L.) and water velvet (Azolla filiculoides Lam.) to anionic surfactant sodium-dodecyl-sulphate (SDS).

Science.gov (United States)

Forni, C; Braglia, R; Harren, F J M; Cristescu, S M

2012-04-01

Surfactants are used for several purposes and recently they have attracted the attention for their ability to modify the behavior of other preexistent or co-disposed contaminants, although their use or discharge in wastewaters can represent a real or potential risk for the environment. Lemna minor L. and Azolla filiculoides Lam. are floating aquatic macrophytes, very effective in accumulating several pollutants including sodium dodecyl sulphate (SDS). In this work we evaluated the effects of SDS on these species by determining the stress ethylene production via laser-based trace gas detection, and the activities of enzymes involved in stress response, such as guaiacol peroxidase (G-POD), phenylalanine ammonia-lyase (PAL) and polyphenol-oxidase (PPO). Phenolics content was also determined. The macrophytes were treated with different concentrations of SDS for one week. SDS affected duckweed enzymatic activities and phenol content. While in the fern phenolics amount, PAL, G-POD and PPO activities were not affected by SDS except for 100 ppm SDS, the only concentration that was taken up and not completely degraded. Stress ethylene production was induced only in the fern treated with 50 and 100 ppm SDS. Copyright © 2011 Elsevier B.V. All rights reserved.

Outlook for the U.S. alkylation industry

International Nuclear Information System (INIS)

Felten, J.R.; Bradshaw, T.; McCarthy, K.

1994-01-01

Alkylation has long been recognized in the refining industry as one of the best options to convert refinery olefins into valuable, clean, high octane blending components. In fact, refinery alkylation is a preferred source of blending stocks for reformulated gasoline. However, the hydrofluoric acid (HF) alkylation process and, to a lesser extent, the sulfuric acid (SA) process have come under increasing pressure in the US due to safety and environmental concerns. This paper examines the current outlook for the US alkylation industry including: key trends and driving forces in the industry, the impact of environmental issues on both HF and SA alkylation, US alkylation supply/demand forecast including the outlook for oxygenates, how US refines will respond to the increased demand and restricted supply for alkylates, and the outlook for new solid acid alkylation (SAC) technology

Electrochemical sample preparation for the determination of Cd, Pb, and Cu in the presence of surfactants by stripping voltammetry

International Nuclear Information System (INIS)

Svintsova, L.D.; Chernysheva, N.N.

1997-01-01

The electrochemical pretreatment of aqueous solutions of synthetic surfactants in a diaphragm elelctrolyzer was used in order to diminish surfactant interference. The determination of cadmium, lead, and copper by stripping voltammetry with a mercury-film electrode in model solutions of cetylpyriridinium chloride, sodium lauryl sulfate, and OP-10 was taken as an example. It was found that the reproducibility of anodic peaks of the elements was improved, and the linearity of calibration characteristics was recovered; however, the sensitivity was not always as high as the value in the blank experiment

Effect of 60Co gamma-ray irradiation on dilute aqueous solutions of surfactants

International Nuclear Information System (INIS)

Sawai, Teruko; Shimokawa, Toshinari; Miki, Yasushi; Oseko, Koichi; Sawai, Takeshi

1978-01-01

Present work deals with the effects of gamma irradiation from 60 Co γ-ray source upon aqueous solutions of three kinds of surfactants. When dilute aqueous solutions of sodium dodecyl sulfate (SDS, anionic), cethyl trimethyl ammonium chloride (CTAC, cationic), and polyoxyethylene lauryl ether (POE, non-ionic) were irradiated with γ-rays at a room temperature, the residual concentration, products, surface tension, and forming power were examined by colorimetric method, IR spectrophotometric method, gaschromatography, Ross-Miles method, and Traube's stalagmometer etc. These surfactants were decomposed by the irradiation and thus the surface tension increased and the forming power, on the contrary, decreased with dose. Radiation chemical yields (G-value) of the degradation were about 1 for the solutions of SDS and CTAC, and about 0.3 for the POE solution. From the experimental results, it was found that following chemical reactions seem to occur followed by the radiolysis of water: a) bond cleavage of ester for SDS, of CN for CTAC, and of oxyethylene for POE, b) hydrogen abstraction from the surfactants, c) production of CO bond in the presence of dissolved oxygen. (auth.)

The Effects of Alkyl Chain Combinations on the Structural and Mechanical Properties of Biomimetic Ion Pair Amphiphile Bilayers

Directory of Open Access Journals (Sweden)

Cheng-hao Chen

2017-10-01

Full Text Available Ion pair amphiphile (IPA, a lipid-like complex composed of a pair of cationic and anionic surfactants, has great potentials in various pharmaceutical applications. In this work, we utilized molecular dynamics (MD simulation to systematically examine the structural and mechanical properties of the biomimetic bilayers consist of alkyltrimethyl-ammonium-alkylsulfate (CmTMA+-CnS− IPAs with various alkyl chain combinations. Our simulations show an intrinsic one-atom offset for the CmTMA+ and CnS− alignment, leading to the asymmetric index definition of ΔC = m − (n + 1. Larger |ΔC| gives rise to higher conformational fluctuations of the alkyl chains with the reduced packing order and mechanical strength. In contrast, increasing the IPA chain length enhances the van der Waals interactions within the bilayer and thus improves the bilayer packing order and mechanical properties. Further elongating the CmTMA+-CnS− alkyl chains to m and n ≥ 12 causes the liquid disorder to gel phase transition of the bilayer at 298 K, with the threshold membrane properties of 0.45 nm2 molecular area, deuterium order parameter value of 0.31, and effective bending rigidity of 20 kBT, etc. The combined results provide molecular insights into the design of biomimetic IPA bilayers with wide structural and mechanical characteristics for various applications.

Contact Angle Measurements: an Alternative Approach Towards Understanding the Mechanism of Increased Drug Dissolution from Ethylcellulose Tablets Containing Surfactant and Exploring the Relationship Between Their Contact Angles and Dissolution Behaviors.

Science.gov (United States)

Liu, Tiaotiao; Hao, Jingqiang; Yang, Baixue; Hu, Beibei; Cui, Zhixiang; Li, Sanming

2018-05-01

The addition of surfactant in tablet was a well-defined approach to improve drug dissolution rate. While the selected surfactant played a vital role in improving the wettability of tablet by medium, it was equally important to improve the dissolution rate by permeation effect due to production of pores or the reduced inter-particle adhesion. Furthermore, understanding the mechanism of dissolution rate increased was significant. In this work, contact angle measurement was taken up as an alternative approach for understanding the dissolution rate enhancement for tablet containing surfactant. Ethylcellulose, as a substrate, was used to prepare tablet. Four surfactants, sodium dodecyl sulfate (SDS), sodium dodecylbenzenesulfonate (SDBS), dodecyltrimethylammonium bromide (DTAB), and sodium lauryl sulfonate (SLS), were used. Berberine hydrochloride, metformin hydrochloride, and rutin were selected as model drugs. The contact angle of tablet in the absence and presence of surfactant was measured to explore the mechanism. The dissolution test was investigated to verify the mechanism and to establish a correlation with the contact angle. The result showed that the mechanism was the penetration effect rather than the wetting effect. The dissolution increased with a reduction in the contact angle. DTAB was found to obtain the highest level of dissolution enhancement and the lowest contact angle, while SDS, SDBS, and SLS were found to be the less effective in both dissolution enhancement and contact angle decrease. Therefore, contact angle was a good indicator for dissolution behavior besides exploring the mechanism of increased dissolution, which shows great potential in formula screening.

Performance of Surfactant Methyl Ester Sulphonate solution for Oil Well Stimulation in reservoir sandstone TJ Field

Science.gov (United States)

Eris, F. R.; Hambali, E.; Suryani, A.; Permadi, P.

2017-05-01

Asphaltene, paraffin, wax and sludge deposition, emulsion and water blocking are kinds ofprocess that results in a reduction of the fluid flow from the reservoir into formation which causes a decrease of oil wells productivity. Oil well Stimulation can be used as an alternative to solve oil well problems. Oil well stimulation technique requires applying of surfactant. Sodium Methyl Ester Sulphonate (SMES) of palm oil is an anionic surfactant derived from renewable natural resource that environmental friendly is one of potential surfactant types that can be used in oil well stimulation. This study was aimed at formulation SMES as well stimulation agent that can identify phase transitions to phase behavior in a brine-surfactant-oil system and altered the wettability of rock sandstone and limestone. Performance of SMES solution tested by thermal stability test, phase behavioral examination and rocks wettability test. The results showed that SMES solution (SMES 5% + xylene 5% in the diesel with addition of 1% NaCl at TJformation water and SMES 5% + xylene 5% in methyl ester with the addition of NaCl 1% in the TJ formation water) are surfactant that can maintain thermal stability, can mostly altered the wettability toward water-wet in sandstone reservoir, TJ Field.

Critical micelle concentration of surfactants in aqueous buffered and unbuffered systems

International Nuclear Information System (INIS)

Fuguet, Elisabet; Rafols, Clara; Roses, Marti; Bosch, Elisabeth

2005-01-01

Critical micelle concentration (CMC) of sodium dodecyl sulphate (SDS), lithium perfluorooctanesulfonate (LPFOS), hexadecyltrimethylammonium bromide (HTAB), tetradecyltrimethylammonium bromide (TTAB), and sodium cholate (SC), surfactants commonly used as pseudostationary phases in micellar electrokinetic chromatography (MEKC), have been determined by means of three different methods: MEKC, spectrophotometry, and conductometry. Determinations have been performed in water, and also in different concentrations of phosphate buffer at pH 7.0. CMC values ranging from 8.08 (water) to 1.99 (50 mM phosphate buffer) mM for SDS, from 7.16 (water) to 2,81 (30 mM phosphate buffer) mM for LPFOS, from 3.77 (water) to 1.93 (20 mM phosphate buffer) mM for TTAB, from 0.91 (water) to ∼0.34 (20 mM phosphate buffer) for HTAB, and around 13 mM (20 mM phosphate buffer) for SC, are obtained. The effect of the electrolyte concentration on the CMC, as well as the linear relationship between the electrolyte counter-ion concentration and the CMC are discussed. This linear relationship provides an easy way for users to estimate the CMC of a MEKC system, at a given electrolyte concentration. A comparison between experimental methods, as well as a discussion about the suitability of a given method for the determination of the CMC for a given surfactant system is also provided

L-β-N-methylamino-l-alanine (BMAA) nitrosation generates a cytotoxic DNA damaging alkylating agent: An unexplored mechanism for neurodegenerative disease.

Science.gov (United States)

Potjewyd, G; Day, P J; Shangula, S; Margison, G P; Povey, A C

2017-03-01

L-β-N-methylamino-l-alanine (BMAA) is a non-proteinic amino acid, that is neurotoxic in vitro and in animals, and is implicated in the causation of amyotrophic lateral sclerosis and parkinsonism-dementia complex (ALS-PDC) on Guam. Given that natural amino acids can be N-nitrosated to form toxic alkylating agents and the structural similarity of BMAA to other amino acids, our hypothesis was that N-nitrosation of BMAA might result in a toxic alkylating agent, providing a novel mechanistic hypothesis for BMAA action. We have chemically nitrosated BMAA with sodium nitrite to produce nitrosated BMAA (N-BMAA) which was shown to react with the alkyl-trapping agent, 4-(p-nitrobenzyl)pyridine, cause DNA strand breaks in vitro and was toxic to the human neuroblastoma cell line SH-SY5Y under conditions in which BMAA itself was minimally toxic. Our results indicate that N-BMAA is an alkylating agent and toxin suggesting a plausible and previously unrecognised mechanism for the neurotoxic effects of BMAA. Copyright © 2017 Elsevier B.V. All rights reserved.

Effect of surfactants on the aggregation of pyronin B and pyronin Y in aqueous solution

Energy Technology Data Exchange (ETDEWEB)

Arik, Mustafa; Meral, Kadem [Department of Chemistry, Faculty of Sciences, Atatuerk University, 25240 Erzurum (Turkey); Onganer, Yavuz, E-mail: yonganer@atauni.edu.t [Department of Chemistry, Faculty of Sciences, Atatuerk University, 25240 Erzurum (Turkey)

2009-06-15

Molecular dynamics of pyronin B (PyB) and pyronin Y (PyY) in aqueous solution containing different surfactants were investigated by using absorption and fluorescence spectroscopy techniques. First, the interactions of PyB and PyY with the negatively charged surfactant sodium dodecyl sulphate (SDS) were investigated in the below and above critical micelle concentration (cmc). The H-aggregate formation of the dye compounds was observed for below the cmc of SDS surfactant. The absorbance of H-aggregate absorption band of PyB and PyY decreased according to the aggregate-monomer equilibrium by increasing SDS surfactant concentration towards the cmc. Therefore, equilibrium constants of the aggregate formation and oscillator strengths of monomer and aggregate of the dye compounds were calculated from spectral studies. Moreover, aggregate formation dynamics was discussed in terms of thermodynamic functions by using temperature studies. The interactions of PyB and PyY with the positively charged hexadecyltrimethylammonium bromide (CTAB) and neutral Triton X-100 (TX-100) were also studied and it was observed that there was no aggregate formation on the absorption and fluorescence spectra for below and above the cmc.

Organoclays obtaining starting up of clays sodium

International Nuclear Information System (INIS)

Silva, M.M. da; Mota, M.F.; Oliveira, G.C. de; Rodrigues, M.G.F.

2012-01-01

Clays have several applications in many areas of fields of technology, however, modification of these materials using organic compounds can be performed to obtain further hydrophobic materials, for applications in the adsorption of organic pollutants. This study aimed to analyze the effects of modifying two clays using sodium quaternary ammonium surfactants through ion exchange reaction process, in obtaining organoclays. The samples with sodium and organoclays were characterized by the techniques of X-ray diffraction (XRD), Infrared Spectroscopy in the region (IV), Gravimetric and Differential Thermal Analysis (DTA / TG) and organic adsorption tests. The results show that the process of obtaining organoclay is efficient, and materials have the potential for future applications in removing organic contaminants. (author)

Self-assembly in mixtures of sodium alkyl sulfates and alkyltrimethylammonium bromides : Aggregation behavior and catalytic properties

NARCIS (Netherlands)

Talhout, Reinskje; Engberts, BFN

1997-01-01

Two aqueous mixtures of cationic and anionic surfactants have been studied by means of conductometry, transmission electron microscopy, and microcalorimetry. Their catalytic effects on the decarboxylation of the kinetic probe 6-nitrobenzisoxazole-3-carboxylate (6-NBIC) were also examined in some

Synthesis of Mixed Carbonates via a Three-Component Coupling of Alcohols, CO2, and Alkyl Halides in the Presence of K2CO3 and Tetrabutylammonium Iodide

Directory of Open Access Journals (Sweden)

Yu-Mei Shen

2002-04-01

Full Text Available Various mixed carbonates can be conveniently prepared in good yields using the corresponding alcohols, alkyl halides under CO2 atmosphere in the presence of potassium carbonate or sodium carbonate and tetrabutylammonium iodide.

Surfactant-dependent macrophage response to polypyrrole-based coatings electrodeposited on Ti6Al7Nb alloy

Energy Technology Data Exchange (ETDEWEB)

Mindroiu, Mihaela [University Polytechnica of Bucharest, Faculty of Applied Chemistry and Materials Science, 1-7 Polizu, 011061, Bucharest (Romania); Ion, Raluca [University of Bucharest, Department of Biochemistry and Molecular Biology, 91-95 Spl. Independentei, 050095, Bucharest (Romania); Pirvu, Cristian [University Polytechnica of Bucharest, Faculty of Applied Chemistry and Materials Science, 1-7 Polizu, 011061, Bucharest (Romania); Cimpean, Anisoara, E-mail: anisoara.cimpean@bio.unibuc.ro [University of Bucharest, Department of Biochemistry and Molecular Biology, 91-95 Spl. Independentei, 050095, Bucharest (Romania)

2013-08-01

In this study, polypyrrole (PPy) films were successfully synthesized on Ti6Al7Nb alloy by potentiostatic polymerization in the presence of poly(sodium 4-styrenesulfonate) (NaPSS), t-octylphenoxy polyethoxyethanol (Triton X-100) and N-dodecyl-β-D-maltoside (DM) surfactants. Atomic force microscopy (AFM) analysis of the PPy/surfactant composite films revealed a granular structure characterized by a lower surface roughness than un-modified PPy films. The results demonstrated that addition of surfactants, namely Triton X-100 and DM, can improve electrochemical film stability and corrosion resistance. Further, Triton X-100 enhanced the adhesive strength of PPy films to the substrate. The surfactant type also showed a great influence on the surface wettability, the highest hydrophilic character being observed in the case of PPy/PSS film. Few studies have been devoted to the elucidation of inflammatory cell response to PPy-based materials. Therefore, RAW 264.7 macrophages were cultured on PPy-surfactant films to determine whether they elicit a differential cell behavior in terms of cell adhesion, proliferation, cellular morphology and cytokine secretion. Our results highlight the dependence of macrophage response on the surfactants used in the pyrrole polymerization process and suggest that the immune response to biomaterials coated with PPy films might be controlled by the choice of surfactant molecules. Highlights: • We electrodeposited polypyrrole films on Ti6Al7Nb alloy using three surfactants. • Differences in electrostability and wettability of polypyrrole films were found. • Triton X increased and NaPSS decreased the adhesion of polypyrrole films to Ti6Al7Nb. • Cytoskeletal architecture and macrophage activation were affected by surfactants. • The hydrophilic PPy/PSS coating elicited the lowest inflammatory response.

Surfactant-dependent macrophage response to polypyrrole-based coatings electrodeposited on Ti6Al7Nb alloy

International Nuclear Information System (INIS)

Mindroiu, Mihaela; Ion, Raluca; Pirvu, Cristian; Cimpean, Anisoara

2013-01-01

In this study, polypyrrole (PPy) films were successfully synthesized on Ti6Al7Nb alloy by potentiostatic polymerization in the presence of poly(sodium 4-styrenesulfonate) (NaPSS), t-octylphenoxy polyethoxyethanol (Triton X-100) and N-dodecyl-β-D-maltoside (DM) surfactants. Atomic force microscopy (AFM) analysis of the PPy/surfactant composite films revealed a granular structure characterized by a lower surface roughness than un-modified PPy films. The results demonstrated that addition of surfactants, namely Triton X-100 and DM, can improve electrochemical film stability and corrosion resistance. Further, Triton X-100 enhanced the adhesive strength of PPy films to the substrate. The surfactant type also showed a great influence on the surface wettability, the highest hydrophilic character being observed in the case of PPy/PSS film. Few studies have been devoted to the elucidation of inflammatory cell response to PPy-based materials. Therefore, RAW 264.7 macrophages were cultured on PPy-surfactant films to determine whether they elicit a differential cell behavior in terms of cell adhesion, proliferation, cellular morphology and cytokine secretion. Our results highlight the dependence of macrophage response on the surfactants used in the pyrrole polymerization process and suggest that the immune response to biomaterials coated with PPy films might be controlled by the choice of surfactant molecules. Highlights: • We electrodeposited polypyrrole films on Ti6Al7Nb alloy using three surfactants. • Differences in electrostability and wettability of polypyrrole films were found. • Triton X increased and NaPSS decreased the adhesion of polypyrrole films to Ti6Al7Nb. • Cytoskeletal architecture and macrophage activation were affected by surfactants. • The hydrophilic PPy/PSS coating elicited the lowest inflammatory response

α-TCP cements prepared by syringe-foaming: Influence of Na2HPO4 and surfactant concentration.

Science.gov (United States)

Vásquez, A F; Domínguez, S; Loureiro Dos Santos, L A

2017-12-01

The lack of intrinsic open porosity in calcium phosphate cements slows down the resorption rate and bone ingrowth when implanted In Vivo. In this study, macroporous structures were obtained by mixing α-TCP cement with a foamed liquid phase containing different concentrations of sodium hydrogen phosphate and a nonionic surfactant. The cement paste was prepared by hand mixing in a novel system of two syringes connected by a tube. Two different liquid to powder (L/P) ratios were used to prepare the cement paste. The cement samples showed open macropores with diameters>100μm. The specimens prepared with lower L/P ratio showed smaller porosity, macroporosity and pore size distribution. The cohesion of the cement paste in liquid solutions was assessed by adding 2wt% sodium alginate to the liquid phase. This study suggests that the final macrostructure of the foamed cements can be controlled by varying the phosphate and surfactant concentrations in the liquid phase and the L/P ratio. Copyright © 2017 Elsevier B.V. All rights reserved.

Thyme oil nanoemulsions coemulsified by sodium caseinate and lecithin.

Science.gov (United States)

Xue, Jia; Zhong, Qixin

2014-10-08

Many nanoemulsions are currently formulated with synthetic surfactants. The objective of the present work was to study the possibility of blending sodium caseinate (NaCas) and lecithin to prepare transparent thyme oil nanoemulsions. Thyme oil was emulsified using NaCas and soy lecithin individually or in combination at neutral pH by shear homogenization. The surfactant combination improved the oil content in transparent/translucent nanoemulsions, from 1.0% to 2.5% w/v for 5% NaCas with and without 1% lecithin, respectively. Nanoemulsions prepared with the NaCas-lecithin blend had hydrodynamic diameters smaller than 100 nm and had significantly smaller and more narrowly distributed droplets than those prepared with NaCas or lecithin alone. Particle dimension and protein surface load data suggested the coadsorption of both surfactants on oil droplets. These characteristics of nanoemulsions minimized destabilization mechanisms of creaming, coalescence, and Ostwald ripening, as evidenced by no significant changes in appearance and particle dimension after 120-day storage at 21 °C.

Optimization of palm oil extraction from Decanter cake of small crude palm oil mill by aqueous surfactant solution using RSM

Science.gov (United States)

Ahmadi Pirshahid, Shewa; Arirob, Wallop; Punsuvon, Vittaya

2018-04-01

The use of hexane to extract vegetable oil from oilseeds or seed cake is of growing concern due to its environmental impact such as its smelling and toxicity. In our method, used Response Surface Methodology (RSM) was applied to study the optimum condition of decanter cake obtained from small crude palm oil with aqueous surfactant solution. For the first time, we provide an optimum condition of preliminary study with decanter cake extraction to obtain the maximum of oil yield. The result from preliminary was further used in RSM study by using Central Composite Design (CCD) that consisted of thirty experiments. The effect of four independent variables: the concentration of Sodium Dodecyl Sulfate (SDS) as surfactant, temperature, the ratio by weight to volume of cake to surfactant solution and the amount of sodium chloride (NaCl) on dependent variables are studied. Data were analyzed using Design-Expert 8 software. The results showed that the optimum condition of decanter cake extraction were 0.016M of SDS solution concentration, 73°C of extraction temperature, 1:10 (g:ml) of the ratio of decanter cake to SDS solution and 2% (w/w) of NaCl amount. This condition gave 77.05% (w/w) oil yield. The chemical properties of the extracted palm oil from this aqueous surfactant extraction are further investigated compared with the hexane extraction. The obtained result showed that all properties of both extractions were nearly the same.

Graft copolymerization of a series of alkyl acrylates and alkyl methacrylates onto polyethylene

International Nuclear Information System (INIS)

Zurakowska-Orszagh, J.; Soerjosoeharto, K.; Busz, W.; Oldziejewski, J.

1977-01-01

Graft copolymerization of a series of alkyl acrylates and alkyl methacrylates into polyethylene of Polish production was investigated, using benzoyl peroxide as the initiator as well as preirradiation technique, namely ionizing radiation from a 60 Co γ-source. The effect of α-carbon methyl substituent of methacrylates as well as the influence of the length of alkyl chains in the ester groups of both series of monomers into the grafting process was observed. The ungrafted and some of the grafted polyethylene film obtained was studied by infrared spectrophotometry. (author)

On the use of sodium lignosulphonate for enhanced oil recovery

Science.gov (United States)

Azis, M. M.; Rachmadi, H.; Wintoko, J.; Yuliansyah, A. T.; Hasokowati, W.; Purwono, S.; Rochmadi, W.; Murachman, B.

2017-05-01

There has been large interest to utilize oil reservoirs in Indonesia by using Enhanced Oil Recovery (EOR) processes. Injection of surfactant as a part of chemical injection technique in EOR is known to aid the mobility and reduction in surface tension. One potential surfactant for EOR application is Sodium Lignosulphonate (SLS) which can be made from various sources particularly empty fruit bunch of oil palm and black liquor from kraft pulp production. Here, we will discuss a number of methods for SLS production which includes lignin isolation techniques and sulphonation reaction. The use of SLS alone as EOR surfactant, however, is often not feasible as the Interfacial Tension (IFT) value of SLS is typically above the order of 10-3 dyne/cm which is mandated for EOR application. Hence, brief discussion on SLS formulation screening is provided which illustrates an extensive labwork experience during the SLS development in our lab.

Anionic Surfactant as a Corrosion Inhibitor for Synthesized Ferrous Alloy in Acidic Solution

Directory of Open Access Journals (Sweden)

Farida Kellou-Kerkouche

2013-01-01

Full Text Available The effect of temperature on the corrosion behaviour of a synthesized iron-based alloy in 1 N sulphuric acid solution has been examined by means of three electrochemical techniques. Thereafter, we studied the influence of an anionic surfactant (sodium dodecyl benzene sulfonate at various concentrations on the electrochemical behaviour of the ferrous alloy. The obtained results show that the temperature increase reduced the performance of the used alloy, in the acidic environment. Otherwise, the surfactant inhibits the alloy dissolution in the sulphuric acid, through its adsorption on the metal surface without modifying the mechanism of corrosion process. We also noticed that the highest inhibition effect is obtained at a concentration above its critical micelle concentration (CMC. Langmuir adsorption isotherm fits well with the experimental data.

Influence of Surfactant Sorbitan Monolaurate to Suspension Polymerization of Polyacrylic Acid Super absorbent

International Nuclear Information System (INIS)

Dewi Sondari; Nuri Astrini; Lik Anah; Agus Haryono

2008-01-01

A super absorbent polymer has been prepared by suspension polymerization reaction using acrylic acid, sodium hydroxide, cyclohexane, potassium persulfate as initiator and sorbitan monolaurate as surfactant. The effect of different weight ratio of acrylic acid/sorbitan monolaurate 20/1, 20/2 and 20/3 were investigated based on its swelling properties, chemical structure by using Fourier Transform-Infra Red (FTIR) Spectroscopy and the surface morphology by scanning electron microscopy (SEM). The molecular weight of polyacrylic acid super absorbent was determinate by intrinsic viscosity measurements in 2 M aqueous sodium hydroxide at 25 o C. The study showed sample with weight ratio of acrylic acid/sorbitan monolaurate = 20/2 have best swelling properties. (author)

Photoinduced, copper-catalyzed alkylation of amides with unactivated secondary alkyl halides at room temperature.

Science.gov (United States)

Do, Hien-Quang; Bachman, Shoshana; Bissember, Alex C; Peters, Jonas C; Fu, Gregory C

2014-02-05

The development of a mild and general method for the alkylation of amides with relatively unreactive alkyl halides (i.e., poor substrates for SN2 reactions) is an ongoing challenge in organic synthesis. We describe herein a versatile transition-metal-catalyzed approach: in particular, a photoinduced, copper-catalyzed monoalkylation of primary amides. A broad array of alkyl and aryl amides (as well as a lactam and a 2-oxazolidinone) couple with unactivated secondary (and hindered primary) alkyl bromides and iodides using a single set of comparatively simple and mild conditions: inexpensive CuI as the catalyst, no separate added ligand, and C-N bond formation at room temperature. The method is compatible with a variety of functional groups, such as an olefin, a carbamate, a thiophene, and a pyridine, and it has been applied to the synthesis of an opioid receptor antagonist. A range of mechanistic observations, including reactivity and stereochemical studies, are consistent with a coupling pathway that includes photoexcitation of a copper-amidate complex, followed by electron transfer to form an alkyl radical.

Comparative Effects of Water, Acid and Sodium Benzoate as ...

African Journals Online (AJOL)

The relative effects of water, sulphuric acid and sodium benzoate as additives on the micelle-catalyzed aquation reactions of the complexes:Fe(Me2Phen)3 2+ and FE(Me4Phen) were studied in acetone using Triton X-100 (TX-100), as the surfactant-catalyst. FE(Me4Phen)2+ equates faster than FE(Me2Phen)2+ in the ...

Interfce alkylation of ethyldiphenylphosphinylacetate

International Nuclear Information System (INIS)

Yarkevich, A.N.; Tsvetkov, E.N.

1994-01-01

The paper deals with the alkylation of the methyline group of ethyldiphenylphosphinylacetate (1) by different alkylating agents in the presence of Cs 2 CO 3 . In all cases the application of Cs 2 CO 3 results in a significant increase of reaction rate. 10 refs., 3 tabs

Formation of enamines by alkylation of imines

NARCIS (Netherlands)

Heiszwolf, G.J.; Kloosterziel, H.

1966-01-01

cf. CA 64, 12473c. With ice-cooling, 1 equiv. alkylating agent was added to one equiv. of the imine in 1M soln. in a solvent in the presence of NaH to give both N- and C-alkylated products. The following summarizes the date (imine, solvent, alkylating agent, % unreacted imine, % N-alkylated product,

Sulfonium Salts as Alkylating Agents for Palladium-Catalyzed Direct Ortho Alkylation of Anilides and Aromatic Ureas.

Science.gov (United States)

Simkó, Dániel Cs; Elekes, Péter; Pázmándi, Vivien; Novák, Zoltán

2018-02-02

A novel method for the ortho alkylation of acetanilide and aromatic urea derivatives via C-H activation was developed. Alkyl dibenzothiophenium salts are considered to be new reagents for the palladium-catalyzed C-H activation reaction, which enables the transfer of methyl and other alkyl groups from the sulfonium salt to the aniline derivatives under mild catalytic conditions.

Molecular design of sequence specific DNA alkylating agents.

Science.gov (United States)

Minoshima, Masafumi; Bando, Toshikazu; Shinohara, Ken-ichi; Sugiyama, Hiroshi

2009-01-01

Sequence-specific DNA alkylating agents have great interest for novel approach to cancer chemotherapy. We designed the conjugates between pyrrole (Py)-imidazole (Im) polyamides and DNA alkylating chlorambucil moiety possessing at different positions. The sequence-specific DNA alkylation by conjugates was investigated by using high-resolution denaturing polyacrylamide gel electrophoresis (PAGE). The results showed that polyamide chlorambucil conjugates alkylate DNA at flanking adenines in recognition sequences of Py-Im polyamides, however, the reactivities and alkylation sites were influenced by the positions of conjugation. In addition, we synthesized conjugate between Py-Im polyamide and another alkylating agent, 1-(chloromethyl)-5-hydroxy-1,2-dihydro-3H-benz[e]indole (seco-CBI). DNA alkylation reactivies by both alkylating polyamides were almost comparable. In contrast, cytotoxicities against cell lines differed greatly. These comparative studies would promote development of appropriate sequence-specific DNA alkylating polyamides against specific cancer cells.

Evaluation of anionic surfactant concentrations in US effluents and probabilistic determination of their combined ecological risk in mixing zones.

Science.gov (United States)

McDonough, Kathleen; Casteel, Kenneth; Itrich, Nina; Menzies, Jennifer; Belanger, Scott; Wehmeyer, Kenneth; Federle, Thomas

2016-12-01

Alcohol sulfates (AS), alcohol ethoxysulfates (AES), linear alkyl benzenesulfonates (LAS) and methyl ester sulfonates (MES) are anionic surfactants that are widely used in household detergents and consumer products resulting in over 1 million tons being disposed of down the drain annually in the US. A monitoring campaign was conducted which collected grab effluent samples from 44 wastewater treatment plants (WWTPs) across the US to generate statistical distributions of effluent concentrations for anionic surfactants. The mean concentrations for AS, AES, LAS and MES were 5.03±4.5, 1.95±0.7, 15.3±19, and 0.35±0.13μg/L respectively. Since each of these surfactants consist of multiple homologues that differ in their toxicity, the concentration of each homologue measured in an effluent sample was converted into a toxic unit (TU) by normalizing to the predicted no effect concentration (PNEC) derived from high tier effects data (mesocosm studies). The statistical distributions of the combined TUs in the effluents were used in combination with distributions of dilution factors for WWTP mixing zones to conduct a US-wide probabilistic risk assessment for the aquatic environment for each of the surfactants. The 90th percentile level of TUs for AS, AES, LAS and MES in mixing zones were 1.89×10 -2 , 2.73×10 -3 , 2.72×10 -2 , and 3.65×10 -5 under 7Q10 (lowest river flow occurring over a 7day period every 10years) low flow conditions. Because these surfactants have the same toxicological mode of action, the TUs were summed and the aquatic safety for anionic surfactants as a whole was assessed. At the 90th percentile level under the conservative 7Q10 low flow conditions the forecasted TUs were 4.21×10 -2 which indicates that there is a significant margin of safety for the class of anionic surfactants in US aquatic environments. Copyright © 2016 Elsevier B.V. All rights reserved.

Bis(trialkylsilyl) peroxides as alkylating agents in the copper-catalyzed selective mono-N-alkylation of primary amides.

Science.gov (United States)

Sakamoto, Ryu; Sakurai, Shunya; Maruoka, Keiji

2017-06-13

The copper-catalyzed selective mono-N-alkylation of primary amides with bis(trialkylsilyl) peroxides as alkylating agents was reported. The results of a mechanistic study suggest that this reaction should proceed via a free radical process that includes the generation of alkyl radicals from bis(trialkylsilyl) peroxides.

Inactivation of Escherichia coli O157:H7 in vitro and on the surface of spinach leaves by biobased surfactants

Science.gov (United States)

This study was conducted to evaluate the effect of biosurfactants on the populations of Escherichia coli O157:H7 in suspension and on spinach leaves. Eight surfactants including four soybean oil-based biosurfactants, sodium dodecyl sulfate (SDS), polyoxyethylene sorbitan monooleate (Tween 80), sopho...

Pulmonary surfactant and lung transplantation

NARCIS (Netherlands)

Erasmus, Michiel Elardus

1997-01-01

Pulmonary surfactant lowers the surface tension at the air-water interface inside the alveolus. This is achieved by adsorption of surfactant phospholipids at the air-water interface, a process controlled by surfactant-associated proteins, such as SP-A. In this way, surfactant prevents collapse of

Surfactant-enhanced bioremediation of PAH- and PCB-contaminated soils

International Nuclear Information System (INIS)

Ghosh, M.M.; Yeom, I.T.; Shi, Z.; Cox, C.D.; Robinson, K.G.

1995-01-01

The role of surfactants in the desorption of soil-bound polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs) was investigated. The solubilization of individual PAHs in an extract of a weathered, coal tar-contaminated soil containing a mixture of PAHs and other petroleum derivatives was found to be significantly less than that for pure compounds. Batch soil washing with Triton X-100 (a commercial, nonionic alkyl phenol ethoxylate) was found to increase the effective diffusion rate of PAHs from the contaminated soil by four orders of magnitude compared to that obtained by gas purging when the results were analyzed using a radial diffusion model. At concentrations of up to 24 times its critical micelle concentration (CMC), Triton X-100 did not seem to enhance hydrocarbon degradation in the coal tar-contaminated soil; however, the biosurfactant rhamnolipid R1, at a concentration of 50x CMC, increased the rate of mineralization of 4,4'-chlorinated biphenyl mobilized from a laboratory-contaminated soil by more than 60 times

40 CFR 721.9892 - Alkylated urea.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Alkylated urea. 721.9892 Section 721... Alkylated urea. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as an alkylated urea (PMN P-93-1649) is subject to reporting under this...

Increased release of fermentable sugars from elephant grass by enzymatic hydrolysis in the presence of surfactants

International Nuclear Information System (INIS)

Menegol, Daiane; Scholl, Angélica Luisi; Fontana, Roselei Claudete; Dillon, Aldo José Pinheiro; Camassola, Marli

2014-01-01

Highlights: • Milling is an attractive method to enhance the enzymatic hydrolysis of biomass. • Surfactants improve the efficiency of lignocellulose enzymatic hydrolysis. • Pretreatment with NaOH, smaller particle size and Tween 80® were more efficient. - Abstract: In the search for renewable energy sources, elephant grass is an alternative substrate for ethanol production, but this substrate must be hydrolyzed by cellulases and xylanases to liberate fermentable sugars. During enzymatic hydrolysis, cellulase activity is reduced by the irreversible adsorption of cellulase onto cellulose, decreasing the rate of hydrolysis. Adding surfactants during hydrolysis can improve the process. The effects of Tween® and Triton® surfactants on the enzymatic hydrolysis of elephant grass were evaluated in this context. The data indicate that pretreatment with sodium hydroxide, along with a smaller particle size (0.075–0.152 mm) and the use of Tween 80®, increased the efficiency of releasing reducing sugars from pretreated elephant grass biomass. Thus, it is possible to reduce grinding costs in second-generation ethanol production through the use of surfactants, as they allow efficient hydrolysis of larger biomass particles

Identify alkylation hazards

International Nuclear Information System (INIS)

Scott, B.

1992-01-01

This paper reports that extensive experience shows that alkylation plants regardless of acid catalyst choice, can be operated safely, and with minimum process risk to employees or neighbors. Both types of plants require a comprehensive and fully supported hazard management program that accounts for differing physical properties of the acids involved. Control and mitigation cost to refiners will vary considerably from plant to plant and location to location. In the author's experience, the order of magnitude costs will be about $1 to $2 million for a sulfuric acid (SA) alkylation plant, and about $10 to $15 million for a hydrofluoric acid (HF) plant. These costs include water supply systems and impoundment facilities for contaminated runoff water. The alkylation process, which chemically reacts isobutane and light olefins in the presence of a strong acid catalyst into a premium gasoline component is described

Microemulsion-based lycopene extraction: Effect of surfactants, co-surfactants and pretreatments.

Science.gov (United States)

Amiri-Rigi, Atefeh; Abbasi, Soleiman

2016-04-15

Lycopene is a potent antioxidant that has received extensive attention recently. Due to the challenges encountered with current methods of lycopene extraction using hazardous solvents, industry calls for a greener, safer and more efficient process. The main purpose of present study was application of microemulsion technique to extract lycopene from tomato pomace. In this respect, the effect of eight different surfactants, four different co-surfactants, and ultrasound and enzyme pretreatments on lycopene extraction efficiency was examined. Experimental results revealed that application of combined ultrasound and enzyme pretreatments, saponin as a natural surfactant, and glycerol as a co-surfactant, in the bicontinuous region of microemulsion was the optimal experimental conditions resulting in a microemulsion containing 409.68±0.68 μg/glycopene. The high lycopene concentration achieved, indicates that microemulsion technique, using a low-cost natural surfactant could be promising for a simple and safe separation of lycopene from tomato pomace and possibly from tomato industrial wastes. Copyright © 2015 Elsevier Ltd. All rights reserved.

A sensitive fluorescent probe for the polar solvation dynamics at protein-surfactant interfaces.

Science.gov (United States)

Singh, Priya; Choudhury, Susobhan; Singha, Subhankar; Jun, Yongwoong; Chakraborty, Sandipan; Sengupta, Jhimli; Das, Ranjan; Ahn, Kyo-Han; Pal, Samir Kumar

2017-05-17

Relaxation dynamics at the surface of biologically important macromolecules is important taking into account their functionality in molecular recognition. Over the years it has been shown that the solvation dynamics of a fluorescent probe at biomolecular surfaces and interfaces account for the relaxation dynamics of polar residues and associated water molecules. However, the sensitivity of the dynamics depends largely on the localization and exposure of the probe. For noncovalent fluorescent probes, localization at the region of interest in addition to surface exposure is an added challenge compared to the covalently attached probes at the biological interfaces. Here we have used a synthesized donor-acceptor type dipolar fluorophore, 6-acetyl-(2-((4-hydroxycyclohexyl)(methyl)amino)naphthalene) (ACYMAN), for the investigation of the solvation dynamics of a model protein-surfactant interface. A significant structural rearrangement of a model histone protein (H1) upon interaction with anionic surfactant sodium dodecyl sulphate (SDS) as revealed from the circular dichroism (CD) studies is nicely corroborated in the solvation dynamics of the probe at the interface. The polarization gated fluorescence anisotropy of the probe compared to that at the SDS micellar surface clearly reveals the localization of the probe at the protein-surfactant interface. We have also compared the sensitivity of ACYMAN with other solvation probes including coumarin 500 (C500) and 4-(dicyanomethylene)-2-methyl-6-(p-dimethylamino-styryl)-4H-pyran (DCM). In comparison to ACYMAN, both C500 and DCM fail to probe the interfacial solvation dynamics of a model protein-surfactant interface. While C500 is found to be delocalized from the protein-surfactant interface, DCM becomes destabilized upon the formation of the interface (protein-surfactant complex). The timescales obtained from this novel probe have also been compared with other femtosecond resolved studies and molecular dynamics simulations.

Model study of enhanced oil recovery by flooding with aqueous surfactant solution and comparison with theory.

Science.gov (United States)

Fletcher, Paul D I; Savory, Luke D; Woods, Freya; Clarke, Andrew; Howe, Andrew M

2015-03-17

With the aim of elucidating the details of enhanced oil recovery by surfactant solution flooding, we have determined the detailed behavior of model systems consisting of a packed column of calcium carbonate particles as the porous rock, n-decane as the trapped oil, and aqueous solutions of the anionic surfactant sodium bis(2-ethylhexyl) sulfosuccinate (AOT). The AOT concentration was varied from zero to above the critical aggregation concentration (cac). The salt content of the aqueous solutions was varied to give systems of widely different, post-cac oil-water interfacial tensions. The systems were characterized in detail by measuring the permeability behavior of the packed columns, the adsorption isotherms of AOT from the water to the oil-water interface and to the water-calcium carbonate interface, and oil-water-calcium carbonate contact angles. Measurements of the percent oil recovery by pumping surfactant solutions into calcium carbonate-packed columns initially filled with oil were analyzed in terms of the characterization results. We show that the measured contact angles as a function of AOT concentration are in reasonable agreement with those calculated from values of the surface energy of the calcium carbonate-air surface plus the measured adsorption isotherms. Surfactant adsorption onto the calcium carbonate-water interface causes depletion of its aqueous-phase concentration, and we derive equations which enable the concentration of nonadsorbed surfactant within the packed column to be estimated from measured parameters. The percent oil recovery as a function of the surfactant concentration is determined solely by the oil-water-calcium carbonate contact angle for nonadsorbed surfactant concentrations less than the cac. For surfactant concentrations greater than the cac, additional oil removal occurs by a combination of solubilization and emulsification plus oil mobilization due to the low oil-water interfacial tension and a pumping pressure increase.

Thermodynamics of micellization of cationic surfactants based on O-alkyl and O-perfluoro-N,N'-diisopropylisourea: Effect of the counter ion nature

International Nuclear Information System (INIS)

Lehanine, Zineb; Badache, Leila

2011-01-01

Graphical abstract: The pseudo phase thermodynamic model was applied to study the process of micellization of O-dodecyl- and O-tridecafluorooctyl-N,N'-diisopropylisourea hydrohalogenides. Free energy of micellization is weakly temperature dependent and decreased slightly with the size of the counterion, indicating a more favored micellization. Enthalpies and entropies of micellization decrease strongly with increasing temperature. The enthalpy-entropy compensation phenomenon was observed for all the surfactants studied. Highlights: → The pseudo phase thermodynamic model was applied to study the process of micellization of O-dodecyl- and O-tridecafluorooctyl-N,N'-diisopropylisourea hydrohalogenides. → Free energy of micellization is weakly temperature dependent and decreased slightly with the size of the counterion, indicating a more favored micellization. → Enthalpies and entropies of micellization decrease strongly with increasing temperature. → The enthalpy-entropy compensation phenomenon was observed for all the surfactants studied. - Abstract: A thermodynamic study on the micellization process of two series of cationic surfactants, viz. the O-dodecyl-N,N'-diisopropylisourea hydrochloride, hydrobromide, and hydroiodide and the O-tridecafluorooctyl-N,N'-diisopropylisourea hydrochloride, and hydrobromide, is reported. In order to explain the effect of the counter ion nature in the micellization process, thermodynamic parameters to include the standard free energy (ΔG mic 0 ), enthalpy (ΔH mic 0 ), entropy (ΔS mic 0 ), and heat capacity (ΔC p,mic 0 ) of micellization have been discussed. These parameters are evaluated from the variation of the critical micelle concentration (CMC) with temperature by fitting these values to expressions derived on the basis of a micellization thermodynamic model. The heat capacities of micellization (ΔC p,mic 0 ) were determined from the temperature dependence of ΔH mic 0 . For both surfactant series, the free energy of

Tungsten Oxide and Polyaniline Composite Fabricated by Surfactant-Templated Electrodeposition and Its Use in Supercapacitors

Directory of Open Access Journals (Sweden)

Benxue Zou

2014-01-01

Full Text Available Composite nanostructures of tungsten oxide and polyaniline (PANI were fabricated on carbon electrode by electrocodeposition using sodium dodecylbenzene sulfonate (SDBS as the template. The morphology of the composite can be controlled by changing SDBS surfactant and aniline monomer concentrations in solution. With increasing concentration of aniline in surfactant solution, the morphological change from nanoparticles to nanofibers was observed. The nanostructured WO3/PANI composite exhibited enhanced capacitive charge storage with the specific capacitance of 201 F g−1 at 1.28 mA cm−2 in large potential window of -0.5~ 0.65 V versus SCE compared to the bulk composite film. The capacitance retained about 78% when the sweeping potential rate increased from 10 to 150 mV/s.

Adsorption of anionic surfactant on porous and nonporous polyethylene terephthalate films

International Nuclear Information System (INIS)

Yamauchi, Yu.; Apel, P.Yu.

2016-01-01

We study the adsorption of anionic surfactant, sodium dodecyl diphenyloxide disulfonate (SDDD) on three types of polyethylene terephthalate (PET) substrates from aqueous solutions of SDDD of different concentrations. Neutral electrolyte (KCl) was added to the solutions to vary the ionic strength. Three types of substrates were used: 1) original PET film; 2) etched nonporous film, obtained from pristine film by chemical etching and bearing negative charge on the surface; 3) etched porous membranes, fabricated from pristine film by ion irradiation and subsequent chemical etching. The membranes have negative charge on the flat surface and on the inner pore walls. The comparison shows that the negative charge on the flat surface has weak effect on adsorption of the anionic surfactant, and the SDDD adsorption on the inner walls of pores is much weaker than on flat surface, even if the pore radius is significantly larger than the Debye length. This «exclusion» effect strongly depends on ionic strength of solution. [ru

A comparison study between sodium dodecyl sulfate and sodium dodecyl sulfonate with respect to the thermodynamic properties, micellization, and interaction with poly(ethylene glycol) in aqueous solutions

Energy Technology Data Exchange (ETDEWEB)

Sadeghi, Rahmat, E-mail: rsadeghi@uok.ac.ir [Department of Chemistry, University of Kurdistan, Sanandaj (Iran, Islamic Republic of); Shahabi, Somayyeh [Department of Chemistry, University of Kurdistan, Sanandaj (Iran, Islamic Republic of)

2011-09-15

Graphical abstract: Apparent molar volume against molality: o, {center_dot}, and {Delta}, respectively in water, (1 and 4) wt% PEG solution at 293.15 K; x, {Delta}, and lozenge, respectively in water, (1 and 4) wt% PEG solution at 313.15 K. Research Highlights: > C{sub 12}H{sub 25}SO{sub 3}Na(SDSn) was seen to interact with PEG more weakly than C{sub 12}H{sub 25}SO{sub 4}Na(SDS). > The constraints on molecular mobility of SDS micelles are larger than those of SDSn. > Entropy change on micellization for SDSn is larger than those for SDS. > Micelle formation of SDS is less endothermic and more spontaneous than that of SDSn. > Micelles of SDS have smaller aggregation number than that of SDSn. - Abstract: The density, sound velocity, and conductivity measurements were performed on aqueous solutions of sodium dodecyl sulfate (C{sub 12}H{sub 25}SO{sub 4}Na) or sodium dodecyl sulfonate (C{sub 12}H{sub 25}SO{sub 3}Na) in the absence and presence of poly(ethylene glycol) (PEG) at different temperatures. Changes in the apparent molar volumes and isentropic compressibilities upon micellization were derived using a pseudophase-transition approach and the infinite dilution apparent molar properties of the monomer and micellar form of C{sub 12}H{sub 25}SO{sub 4}Na and C{sub 12}H{sub 25}SO{sub 3}Na were determined. Variations of the critical micelle concentrations (CMCs) of both surfactants in the solutions investigated with temperature were obtained from which thermodynamic parameters of micellization were estimated. It was found that at low temperature the micelle formation process is endothermic and therefore, this process must be entropically driven. However, upon increasing the temperature, the enthalpic factor becomes more significant and, at temperatures higher than 303.15 K the micellization is enthalpy driven. The interactions between C{sub 12}H{sub 25}SO{sub 4}Na/C{sub 12}H{sub 25}SO{sub 3}Na and PEG were studied and it was found that sodium alkyl sulfonates were seen

Protolytic properties and complexation of DL-alpha-alanine and DL-alpha-valine and their dipeptides in aqueous and micellar solutions of surfactants

NARCIS (Netherlands)

Chernyshova, O. S.; Boychenko, Oleksandr; Abdulrahman, H.; Loginova, L. P.

In this work we investigated the effect of the micellar media of anionic (sodium dodecylsulfate, SDS), cationic (cetylpiridinium chloride, CPC) and non-ionic (Brij-35) surfactants on the protolytic properties of amino acids DL-alpha-alanine, DL-alpha-valine and dipeptides

Determination of reaction rate constants for alkylation of 4-(p-nitrobenzyl) pyridine by different alkylating agents.

Science.gov (United States)

Walles, S A

1980-02-01

The rate constants have been determined for the reaction between some different alkylating agents and 4-(p-nitrobenzyl) pyridine (NBP) in methanol. These constants have been compared with those for alkylation of aniline in water. All the constants were lower in methanol than in water but in different degrees. The rate constants of the different alkylating agents have been calculated at a nucleophilic strength n=2. The genetic risk defined as the degree of alkylation of a nucleophile (n=2) is equivalent to the rate constant kn=2 and the target dose. The dependence of the genetic risk on the rate constant (kn=2) is discussed.

Alkylation of enolate anions formation of enol ethers

NARCIS (Netherlands)

Heiszwolf, G.J.; Kloosterziel, H.

1970-01-01

The alkylation of ambident enolate anions-obtained from aliphatic ketones (and one particular type of aldehyde)-was studied using various solvents, bases, alkylating agents and substrates. Alkylation with a reactive alkylating agent (dialkyl sulfates, triethyloxonium fluoroborate) in an aprotic

Design of Agglomerated Crystals of Ibuprofen During Crystallization: Influence of Surfactant

Directory of Open Access Journals (Sweden)

Maryam Maghsoodi

2011-01-01

Full Text Available Objective(sIbuprofen is a problematic drug in tableting, and dissolution due to its poor solubility, hydrophobicity, and tendency to stick to surface. Because of the bad compaction behavior ibuprofen has to be granulated usually before tableting. However, it would be more satisfactory to obtain directly during the crystallization step crystalline particles that can be directly compressed and quickly dissolved. Materials and Methods Crystallization of ibuprofen was carried out using the quasi emulsion solvent diffusion method in presence of surfactant (sodium lauryl sulfate (SLS, Tween 80. The particles were characterized by differential scanning calorimetry (DSC, powder X-ray diffraction (XRPD and were evaluated for particle size, flowability, drug release and tableting behavior. ResultsIbuprofen particles obtained in the presence of surfactants consisted of numerous plate- shaped crystals which had agglomerated together as near spherical shape. The obtained agglomerates exhibited significantly improved micromeritic properties as well as tableting behavior than untreated drug crystals. The agglomerates size and size distribution was largely controlled by surfactant concentration, but there was no significant influence found on the tableting properties. The dissolution tests showed that the agglomerates obtained in presence of SLS exhibited enhanced dissolution rate while the agglomerates made in the presence of Tween 80 had no significant impact on dissolution rate of ibuprofen in comparison to untreated sample. The XRPD and DSC results showed that during the agglomeration process, ibuprofen did not undergo any polymorphic changes.Conclusion The study highlights the influence of surfactants on crystallization process leading to modified performance.

Structure and Conformational Dynamics of DMPC/Dicationic Surfactant and DMPC/Dicationic Surfactant/DNA Systems

Directory of Open Access Journals (Sweden)

Maciej Kozak

2013-04-01

Full Text Available Amphiphilic dicationic surfactants, known as gemini surfactants, are currently studied for gene delivery purposes. The gemini surfactant molecule is composed of two hydrophilic “head” groups attached to hydrophobic chains and connected via molecular linker between them. The influence of different concentrations of 1,5-bis (1-imidazolilo-3-decyloxymethyl pentane chloride (gemini surfactant on the thermotropic phase behaviour of 1,2-dimyristoyl-sn-glycero-3-phosphocholine (DMPC bilayers with and without the presence of DNA was investigated using Fourier transformed infrared (FTIR and circular dichroism (CD spectroscopies, small angle scattering of synchrotron radiation and differential scanning calorimetry. With increasing concentration of surfactant in DMPC/DNA systems, a disappearance of pretransition and a decrease in the main phase transition enthalpy and temperature were observed. The increasing intensity of diffraction peaks as a function of surfactant concentration also clearly shows the ability of the surfactant to promote the organisation of lipid bilayers in the multilayer lamellar phase.

Enantioseparation of palonosetron hydrochloride by micellar electrokinetic chromatography with sodium cholate as chiral selector.

Science.gov (United States)

Tian, Kan; Chen, Hongli; Tang, Jianghong; Chen, Xingguo; Hu, Zhide

2006-11-03

The enantioseparation of four stereoisomers of palonosetron hydrochloride by micellar electrokinetic chromatography using sodium cholate as chiral surfactant was described. Sodium cholate was shown to be effective in separating palonosetron hydrochloride stereoisomers. For method optimization, several parameters such as sodium cholate concentration, buffer pH and concentration, the types and concentration of organic modifiers and applied voltage, on the enantioseparation were evaluated and the optimum conditions were obtained as follows: 30 mM borate buffer (pH 9.40) containing 70 mM sodium cholate and 20% (v/v) methanol with an applied voltage of 20 kV. Under these conditions, baseline separation of palonosetron hydrochloride stereoisomers was achieved within 18 min.

Surfactant Membrane Phases Containing Mixtures of Hydrocarbon and Fluorocarbon Surfactants

International Nuclear Information System (INIS)

de Campo, Liliana; Warr, G.G.

2005-01-01

Full text: We describe the structure and stability of sponge and lamellar phases comprising mixtures of hydrocarbon and fluorocarbon surfactants. Such mixtures can show limited miscibility with each other, forming for example coexisting populations of hydrocarbon rich and fluorocarbon rich micelles under some circumstances. Our system is based on the well-characterised lamellar and sponge phases of cetylpyridinium chloride, hexanol and 0.2M brine, into which the partially fluorinated surfactant N-1H,1H,2H,2H-tridecafluorooctylpyridinium chloride is incorporated. By probing the structures with SAXS (small angle x-ray scattering) and SANS (small angle neutron scattering) using contrast variation, and by characterizing the dynamic properties with dynamic light scattering, we will describe the effect of incorporating the fluorinated surfactant on the phase equilibria and properties of the surfactant membrane structures. (authors)

Mechanism of the immobilization of surfactants on polymeric surfaces by means of an argon plasma treatment: Influence of UV radiation

NARCIS (Netherlands)

Lens, J.P.; Spaay, B.; Terlingen, J.G.A.; Engbers, G.H.M.; Feijen, Jan

1999-01-01

The mechanism of the immobilization of the surfactant sodium 10-undecenoate (C11(:)) on poly(ethylene) (PE) by means of an argon plasma treatment has been investigated. In particular, the influence of the vacuum ultraviolet (UV) radiation emitted by the argon plasma on the immobilization was

DNA minor groove targeted alkylating agents based on bisbenzimidazole carriers: synthesis, cytotoxicity and sequence-specificity of DNA alkylation.

Science.gov (United States)

Smaill, J B; Fan, J Y; Denny, W A

1998-12-01

A series of bisbenzimidazoles bearing a variety of alkylating agents [ortho- and meta-mustards, imidazolebis(hydroxymethyl), imidazolebis(methylcarbamate) and pyrrolebis(hydroxymethyl)], appended by a propyl linker chain, were prepared and investigated for sequence-specificity of DNA alkylation and their cytotoxicity. Previous work has shown that, for para-aniline mustards, a propyl linker is optimal for cytotoxicity. Alkaline cleavage assays using a variety of different labelled oligonucleotides showed that the preferred sequences for adenine alkylation were 5'-TTTANANAANN and 5'-ATTANANAANN (underlined bases show the drug alkylation sites), with AT-rich sequences required on both the 5' and 3' sides of the alkylated adenine. The different aniline mustards showed little variation in alkylation pattern and similar efficiencies of DNA cross-link formation despite the changes in orientation and positioning of the mustard, suggesting that the propyl linker has some flexibility. The imidazole- and pyrrolebis(hydroxymethyl) alkylators showed no DNA strand cleavage following base treatment, indicating that no guanine or adenine N3 or N7 adducts were formed. Using the PCR-based polymerase stop assay, these alkylators showed PCR blocks at 5'-C*G sites (the * nucleotide indicates the blocked site), particularly at 5'-TAC*GA 5'-AGC*GGA, and 5'-AGCC*GGT sequences, caused by guanine 2-NH2 lesions on the opposite strand. Only the (more reactive) imidazolebis(methylcarbamoyl) and pyrrolebis(hydroxymethyl) alkylators demonstrated interstrand cross-linking ability. All of the bifunctional mustards showed large (approximately 100-fold) increases in cytotoxicity over chlorambucil, with the corresponding monofunctional mustards being 20- to 60-fold less cytotoxic. These results suggest that in the mustards the propyl linker provides sufficient flexibility to achieve delivery of the alkylator to favoured (adenine N3) sites in the minor groove, regardless of its exact geometry with

Alkylation of reticular polymers of ethynyl piperidol by alkyl halogen and investigation of the swelling of the products in water

International Nuclear Information System (INIS)

Khakimkhodjaev, S.N.; Khalikov, D.Kh.

1999-01-01

In the paper the results of investigation on alkylation of reticular polymer of ethyl piperidol by methyl Iodide and ethyl Iodide are adduced. It have been shown that in the first case the reaction of an alkylation proceeds up to 100% of a degree of completion. In the second case of an alkylation the highest degree of alkylation reaches only 60% which is connected with formation of secondary structures. In both cases the process of an alkylation results in deriving highly swelled system

Surfactant-Mediated Growth Revisited

International Nuclear Information System (INIS)

Meyerheim, H. L.; Sander, D.; Popescu, R.; Pan, W.; Kirschner, J.; Popa, I.

2007-01-01

The x-ray structure analysis of the oxygen-surfactant-mediated growth of Ni on Cu(001) identifies up to 0.15 monolayers of oxygen in subsurface octahedral sites. This questions the validity of the general view that surfactant oxygen floats on top of the growing Ni film. Rather, the surfactant action is ascribed to an oxygen-enriched zone extending over the two topmost layers. Surface stress measurements support this finding. Our results have important implications for the microscopic understanding of surfactant-mediated growth and the change of the magnetic anisotropy of the Ni films

Occurrence of multi-class surfactants in urban wastewater: contribution of a healthcare facility to the pollution transported into the sewerage system.

Science.gov (United States)

Bergé, Alexandre; Wiest, Laure; Baudot, Robert; Giroud, Barbara; Vulliet, Emmanuelle

2018-04-01

Healthcare facility discharges, by their nature, are often considered as non-domestic effluent, which can provide significant pollution comparatively to other domestic sources. In this context, a total of 12 monthly sampling campaigns were collected from a healthcare facility as well as the output of a sewerage system of Site Pilote de Bellecombe (SIPIBEL) observatory. This study focuses more specifically on 12 surfactants and biocides: four anionics, four cationic, two non-ionic, one zwitterionic, and one dispersive agent, among the most commonly used commercial surfactants. Particular attention was also provided to routine wastewater quality parameters. Both effluents were heavily contaminated by most anionic surfactants; they displayed median concentrations up to 1 to 2 mg/L for linear alkylbenzene sulfonates and between 10 and 100 μg/L for other sodium sulfate congeners (lauryl and laureth). Overall, for the majority of surfactants, the healthcare facility contribution to the total flux reaching the wastewater treatment plant ranges between 5 and 9%.

Surfactants in tribology

CERN Document Server

Biresaw, Girma

2014-01-01

Surface science and tribology play very critical roles in many industries. Manufacture and use of almost all consumer and industrial products rely on the application of advanced surface and tribological knowledge. The fourth in a series, Surfactants in Tribology, Volume 4 provides an update on research and development activities connecting surfactants and tribological phenomena. Written by renowned subject matter experts, the book demonstrates how improved design of surfactants can be harnessed to control tribological phenomena. Profusely illustrated and copiously referenced, the chapters also

Grafting C8-C16 alkyl groups altered the self-assembly and curcumin –loading properties of sodium caseinate in water

OpenAIRE

Yaqiong Zhang; Puyu Yang; Fangyi Yao; Jie Liu; Liangli (Lucy) Yu

2018-01-01

The data presented here are related to the research article entitled “Synthesis and characterization of alkylated caseinate, and its structure-curcumin loading property relationship in water” (Zhang et al., 2018) [1]. This data article reports the detailed spectra information for 1H NMR, 13C NMR and UPLC-Q-TOF MS of the N-succinimidyl fatty acid esters with various alkyl chain lengths (Cn-NHSs, n = 8, 12, 14 and 16). 1H NMR, 13C NMR and UPLC-Q-TOF MS spectra for C16-NHS are shown as an exampl...

A blend of Sodium Humate/SLES/Herbal Oils

Directory of Open Access Journals (Sweden)

Yeliz Akyiğit

2013-08-01

Full Text Available A blend of sodium humate (SH with anionic surfactants such as sodium lauryl ether sulfate (SLES was prepared by solution mixing at medium of herbal oils at 25, 50 and 75°C. Its miscibility studies were carried out by using physical techniques over an extended range of concentration and composition in buffer solution. In addition, to ascertain the state of miscibility of the blends, they were investigated by using UV-visible spectrophotometer and Fourier transform infrared (FTIR. These values revealed that the blend is miscible when the sodium humate content is more than %60 in the blend at all temperatures. There were no important differences in the characteristics of the blends at different temperatures.It was thought that the mechanism ofthe complex formation is realized by making strong intermolecular interaction like hydrogen bonds between the carbonyl groups in humic acid and hydroxyl groups in fatty acids.

Simultaneous quantification of poly-dispersed anionic, amphoteric and nonionic surfactants in simulated wastewater samples using C18 high-performance liquid chromatography-quadrupole ion-trap mass spectrometry

Science.gov (United States)

Levine, Lanfang H.; Garland, Jay L.; Johnson, Jodie V.

2005-01-01

This paper describes the development of a guantitative method for direct and simultaneous determination of three frequently encountered surfactants, amphoteric (cocoamphoacetate, CAA), anionic (sodium laureth sulfate, SLES), and nonionic (alcohol ethoxylate, AE) using a reversed-phase C18 HPLC coupled with an ESI ion-trap mass spectrometer (MS). Chemical composition, ionization characteristics and fragmentation pathways of the surfactants are presented. Positive ESI was effective for all three surfactants in agueous methanol buffered with ammonium acetate. The method enables rapid determinations in small sample volumes containing inorganic salts (up to 3.5 g L(-1)) and multiple classes of surfactants with high specificity by applying surfactant specific tandem mass spectrometric strategies. It has dynamic linear ranges of 2-60, 1.5-40, 0.8-56 mg L(-1) with R2 egual or greater than 0.999, 0.98 and 0.999 (10 microL injection) for CAA, SLES, and AE, respectively.

The alkylation of imine anions formation of enamines

NARCIS (Netherlands)

Heiszwolf, G.J.; Kloosterziel, H.

1970-01-01

The ambident anions derived from imines were alkylated using a variety of solvents and alkylating agents. Under reactive conditions enamines (N-alkylation) are formed as the main products instead of the usually obsd. homologous imines (C-alkylation). The influence of the type of imine, solvent, and

Quantitative estimation of the extent of alkylation of DNA following treatment of mammalian cells with non-radioactive alkylating agents

Energy Technology Data Exchange (ETDEWEB)

Snyder, R.D. (Univ. of Tennessee, Oak Ridge); Regan, J.D.

1981-01-01

Alkaline sucrose sedimentation has been used to quantitate phosphotriester formation following treatment of human cells with the monofunctional alkylating agents methyl and ethyl methanesulfonate. These persistent alkaline-labile lesions are not repaired during short-term culture conditions and thus serve as a useful and precise index of the total alkylation of the DNA.Estimates of alkylation by this procedure compare favorably with direct estimates by use of labeled alkylating agents.

Thermogravimetric studies on alkyl methacrylate polymers and poly(alkyl methacrylate)-grafted polypropylene fibers

International Nuclear Information System (INIS)

Hayakawa, Kiyoshi; Taoda, Hiroshi; Kawase, Kaoru; Tazawa, Masato; Yamakita, Hiromi

1986-01-01

Thermal behavior of several kinds of poly (alkyl methacrylate) and polypropylene-g-poly (alkyl methacrylate) fibers prepared by γ-irradiation was investigated by thermogravimetric measurements with the intermittent analysis of the gaseous products. The degradation of poly (methyl methacrylate) proceeded according to the deploymerization mechanism reproducing the pristine monomer exclusively. The thermogram in inert atmosphere showed the features of a two-step depolymerization, while in air it showed no such a stepwise decrease with the elevating temperature. The dissolution-precipitation treatment of polymer seemed to affect the decomposition behavior. On other alkyl methacrylate polymers, the thermal decomposition generally proceeded also according to the depolymerization mechanism. But, for instance, at least two kinds of products besides its own monomer were formed from poly (isobutyl methacrylate), and their relative fractions differed with the temperature. Polypropylene-g-poly (alkyl methacrylate) fibers showed lowering of initiation temperature of decomposition with the increase in extent of the grafting, and their initiation temperatures of decomposition in air were lower than those in inert atmosphere. (author)

Interactions between fluorinated cationic guar gum and surfactants in the dilute and semi-dilute solutions.

Science.gov (United States)

Wang, Chen; Li, Xiaorui; Li, Peizhi; Niu, Yuhua

2014-01-01

The interactions between the fluorinated cationic guar gum (FCGG) and ionic surfactants including cetyl trimethyl ammonium bromide (CTAB) and sodium lauryl sulfate (SDS) were studied by light scattering, fluorescence spectroscopy, UV-spectrophotometer, (19)F NMR and dynamic rheometer, respectively. The FCGG is prepared with cationic guar gum, isophorone diisocyanate and 2,2,3,4,4,4-hexafluoro-1-butanol. The results show that, with the addition of the surfactants, the stretching degree of the FCGG chains is increased in the FCGG/CTAB solutions, while the dramatical shrinking of FCGG chain, the phase separation and the re-stretched macromolecules appear successively because of the electricity neutralization reaction in the FCGG/SDS system. The mixed hydrophobic domains in all solutions will be reinforced and then dismantled. The solution elasticity shows up the maximum value accordingly. The surfactants can be embedded in the micro-domains and then hinder the fluorinated segmental motions. The interactions between FCGG and SDS are much stronger than those between FCGG and CTAB. Copyright © 2013 Elsevier Ltd. All rights reserved.

Manganese-catalyzed Dehydrogenative Alkylation or α-Olefination of Alkyl-N-Heteroaromatics by Alcohols.

Science.gov (United States)

Kempe, Rhett; Zhang, Guoying; Irrgang, Torsten; Dietel, Thomas; Kallmeier, Fabian

2018-05-02

Catalysis involving earth-abundant transition metals is an option to help save our rare noble metal resources and is especially interesting if novel reactivity or selectivity patterns are observed. We report here on a novel reaction: the dehydrogenative alkylation or α-olefination of alkyl-N-heteroaromatics by alcohols. Manganese complexes developed in our laboratory catalyze the reaction efficiently. Fe and Co complexes stabilized by such ligands are essentially inactive. Hydrogen is liberated during the reaction and bromo or iodo functional groups and olefins can be tolerated. A variety of alkyl-N-heteroaromatics can be functionalized, and benzyl and aliphatic alcohols undergo the reaction. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

DNA modification by alkylating compounds

Energy Technology Data Exchange (ETDEWEB)

Kruglyakova, E.E.

1985-09-01

Results are given for research on the physico-chemical properties of alkylating compounds - nitroso alkyl ureas (NAU) which possess a broad spectrum of biological activity, such as mutagenic, carcinogenic, and anti-tumor action that is due to the alkylation and carbamoylation of DNA as well as other cellular components. Identified chemical products of NAU interaction with DNA and its components are cited. Structural conversions of a DNA macromolecule resulting from its chemical modification are examined. NAU are used to discuss possible biological consequences of DNA modification. 148 references.

A practical and convenient method for the synthesis of anesthetic drug thiopental: using thiourea and sodium ethoxide

Directory of Open Access Journals (Sweden)

Hojat Narimani

2014-02-01

Full Text Available A general, simple, practical and convenient method has been described for the synthesis of anesthetic drug thiopental using thiourea in the presence of sodium ethoxide. Anesthetic drug of thiopental was prepared in two stages; during the first stage, the alkylation of mthyl cyanoacetate was performed which was then to be followed by cyclization. Alkylation of methyl cyanoacetate which was performed by 2-iodopentane in the presence of sodium ethoxide reacts with thiourea and then the process was followed by thiopental prepration in excellent yield. Some important aspects of this methodology are the high reactivity of the substrates, avoidance of the use of hazardous solvents, simplicity of the product separation, low cost of the substrates and reagents and high yield of product. This is a applicable and efficient method for the preparation of thiopental anesthesia in high yield and in an appropriate time.

Surfactant-induced skin irritation and skin repair. Evaluation of the acute human irritation model by noninvasive techniques.

Science.gov (United States)

Wilhelm, K P; Freitag, G; Wolff, H H

1994-06-01

Although the induction of irritant dermatitis by surfactants has been extensively studied in recent years, our understanding of the repair phase of irritant dermatitis is limited. We investigated qualitative and quantitative differences in surfactant-induced irritant skin reactions from short-term exposure to three structurally different surfactants. Sodium lauryl sulfate (SLS), dodecyl trimethyl ammonium bromide (DTAB), and potassium soap were the model irritants. Surfactant solutions (0.5%) were applied for 24 hours to the volar aspect of the forearm of 11 volunteers. Irritant reactions were assessed until complete healing was indicated by visual assessment and by various aspects of skin function, that is, transepidermal water loss (TEWL), erythema (skin color reflectance), and stratum that is, transepidermal water loss (TEWL), erythema (skin color reflectance), and stratum corneum hydration (electrical capacitance). SLS and DTAB induced similar degrees of erythema, whereas SLS induced significantly higher TEWL increase. Although both erythema and TEWL were highest 1 hour after exposure to surfactants, skin dryness was a symptom with delayed onset, justifying the long observation period in this study. Minimum hydration values were measured as late as 7 days after surfactant exposure. Dryness was significantly more pronounced in areas exposed to SLS than in areas exposed to DTAB. Complete repair of the irritant reaction induced by either SLS or DTAB was achieved 17 days after surfactant exposure. Stratum corneum hydration was the last feature to return to baseline values. Potassium soap did not significantly influence any skin function. We emphasize the importance of extended periods needed before a patient with irritant contact dermatitis can be reexposed to irritant substances. The evaluation of the irritation potential of diverse surfactants depended significantly on the feature (erythema vs hydration and TEWL) measured.

Thermodynamic Study of the Ion-Pair Complexation Equilibria of Dye and Surfactant by Spectral Titration and Chemometric Analysis

Directory of Open Access Journals (Sweden)

Hakimeh Abbasi Awal

2017-12-01

Full Text Available Surfactant-dye interactions are very important in chemical and dyeing processes. The dyes interact strongly with surfactant and show new spectrophotometric properties, so the UV-vis absorption spectrophotometric method has been used to study this process and extract some thermodynamic parameters. In this work, the association equilibrium between ionic dyes and ionic surfactant were studied by analyzing spectrophotometric data using chemometric methods. Methyl orange and crystal violet were selected as a model of cationic and anionic dyes respectively. Also sodium dodecyl sulphate and cetyltrimethylammonium bromide were selected as anionic and cationic surfactant, respectively. Hard model methods such as target transform fitting (TTF classical multi-wavelength fitting and soft model method such as multivariate curve resolution (MCR were used to analyze data that were recorded as a function of surfactant concentration in premicellar and postmicellar regions. Hard model methods were used to resolve data using ion-pair model in premicellar region in order to extract the concentration and spectral profiles of individual components and also related thermodynamic parameters. The equilibrium constants and other thermodynamic parameters of interaction of dyes with surfactants were determined by studying the dependence of their absorption spectra on the temperature in the range 293–308 K at concentrations of 5 × 10−6 M and 8 × 10−6 M for dye crystal violet and methyl orange, respectively. In postmicellar region, the MCR-ALS method was applied for resolving data and getting the spectra and concentration profiles in complex mixtures of dyes and surfactants.

Surfactant-assisted growth of anodic nanoporous niobium oxide with a grained surface

Energy Technology Data Exchange (ETDEWEB)

Yoo, Jeong Eun [Department of Chemical Engineering, Inha University, 253 Yonghyun Dong, Nam-Gu, Incheon 402-751 (Korea, Republic of); Choi, Jinsub, E-mail: jinsub@inha.ac.k [Department of Chemical Engineering, Inha University, 253 Yonghyun Dong, Nam-Gu, Incheon 402-751 (Korea, Republic of)

2010-07-15

Nanoporous niobium oxide film with a maximum thickness of 520 nm was prepared by anodizing niobium in a mixture of 1 wt% HF, 1 M H{sub 3}PO{sub 4}, and a small amount of Sodium Dodecyl Sulfate (SDS) surfactant. The porosity of the anodic niobium oxide prepared without SDS is irregular with the surface of the oxide suggesting a grained surface pattern rather than an ordered porous structure. A proper amount of SDS addition can prepare a pore arrangement with stripe patterns. The pore depth and surface pattern were strongly affected by the concentration of SDS and bath temperature. We found that the addition of SDS surfactant facilitated improvement in the chemical resistance of niobium oxide, leading to the formation of pores with a longer length compared to those prepared without a SDS surfactant. This can be in part ascribed to the protection of the surface by the physical adsorption of SDS on the surface due to a charge-charge interaction and be in part attributed to the formation of Nb=O bonding on the outermost oxide layer by SDS. When anodization was carried out for 4 h, the surface dissolution of niobium oxide was observed, which means that the maximum tolerance time against chemical dissolution was less than 4 h.

Mechanisms of action of quinone-containing alkylating agents: DNA alkylation by aziridinylquinones.

Science.gov (United States)

Hargreaves, R H; Hartley, J A; Butler, J

2000-11-01

Aziridinyl quinones can be activated by cellular reductases eg. DT-diaphorase and cytochrome P450 reductase to form highly reactive DNA alkylating agents. The mechanisms by which this activation and alkylation take place are many and varied. Using clinically relevant and experimental agents this review will describe many of these mechanisms. The agents discussed are Mitomycin C, EO9 and analogues, diaziridinylbenzoquinones and the pyrrolo[1, 2-alpha]benzimidazolequinones.

Surfactant loss control in chemical flooding spectroscopic and calorimetric study of adsorption and precipitation on reservoir minerals. Annual report, September 30, 1993--September 30, 1994

Energy Technology Data Exchange (ETDEWEB)

Somasundaran, P.

1995-06-01

The aim of this project is to elucidate the mechanisms underlying adsorption and surface precipitation of flooding surfactants on reservoir minerals. Effect of surfactant structure, surfactant combinations, other inorganic and polymeric species is being studied. A multi-pronged approach consisting of micro and nano spectroscopy, microcalorimetry, electrokinetics, surface tension and wettability is used to achieve the goals. The results of this study should help in controlling surfactant loss in chemical flooding and also in developing optimum structures and conditions for efficient chemical flooding processes. During the second year of this three year contract, adsorption/desorption of single surfactants and select surfactant mixtures on alumina and silica was studied. Surfactants studied include the anionic sodium dodecyl sulfate (SDS), cationic tetradecyl trimethyl ammonium chloride (TTAC), nonionic pentadecylethoxylated nonyl phenol (NP-15) and the nonionic octaethylene glycol n-dodecyl ether (C{sub 12}EO{sub 8}) of varying hydrocarbon chain length. The microstructure of the adsorbed layer in terms of micropolarity and aggregation numbers was probed using fluorescence spectroscopy. Changes of microstructure upon dilution (desorption) were also studied. Presence of the nonionic surfactant in the mixed aggregate led to shielding of the charge of the ionic surfactant which in-turn promoted aggregation but reduced electrostatic attraction between the charged surfactant and the mineral surface. Strong consequences of surfactant interactions in solution upon adsorption as well as correlations between monomer concentrations in mixtures and adsorption were revealed.

Surfactant replacement therapy--economic impact.

Science.gov (United States)

Pejaver, R K; al Hifzi, I; Aldussari, S

2001-06-01

Surfactant replacement is an effective treatment for neonatal respiratory distress syndrome. (RDS). As widespread use of surfactant is becoming a reality, it is important to assess the economic implications of this new form of therapy. A comparison study was carried out at the Neonatal Intensive Care Unit (NICU) of Northwest Armed Forces Hospital, Saudi Arabia. Among 75 infants who received surfactant for RDS and similar number who were managed during time period just before the surfactant was available, but by set criteria would have made them eligible for surfactant. All other management modalities except surfactant were the same for all these babies. Based on the intensity of monitoring and nursing care required by the baby, the level of care was divided as: Level IIIA, IIIB, Level II, Level I. The cost per day per bed for each level was calculated, taking into account the use of hospital immovable equipment, personal salaries of nursing, medical, ancillary staff, overheads and maintenance, depreciation and replacement costs. Medications used, procedures done, TPN, oxygen, were all added to individual patient's total expenditure. 75 infants in the Surfactant group had 62 survivors. They spent a total of 4300 days in hospital. (av 69.35) Out of which 970 d (av 15.65 per patient) were ventilated days. There were 56 survivors in the non-surfactant group of 75. They had spent a total of 5023 days in the hospital (av 89.69/patient) out of which 1490 were ventilated days (av 26.60 d). Including the cost of surfactant (two doses), cost of hospital stay for each infant taking the average figures of stay would be SR 118, 009.75 per surfactant treated baby and SR 164, 070.70 per non-surfactant treated baby. The difference of 46,061 SR is 39.03% more in non-surfactant group. One Saudi rial = 8 Rs (approx at the time study was carried out.) Medical care cost varies from place to place. However, it is definitely cost-effective where surfactant is concerned. Quality adjusted

Experimental contribution to the understanding of the dynamics of spreading of Newtonian fluids: effect of volume, viscosity and surfactant.

Science.gov (United States)

Roques-Carmes, Thibault; Mathieu, Vincent; Gigante, Alexandra

2010-04-01

The dynamics of drop spreading of glycerol-water mixtures with and without surfactant on hydrophilic glass surfaces has been investigated. The influence of different factors, such as viscosity, drop volume and non-ionic alkyl (8-16) glucoside (Plantacare) surfactant concentration on the number and the nature of the spreading regimes is systematically investigated. More than 25 spreading experiments have been performed in order to obtain clear trends. The results confirm the existence of several spreading regimes for the duration of an experiment (200 s). For each regime, the radius can be expressed by a power law of the form R=Kt(n). Both n and K are necessary to identify the regime. The experimental data are compared with the analytical predictions of the combined theory of spreading. One of the main results of this study is that the nature of the regimes is strongly affected by the drop volume, the viscosity and the surfactant concentration. This behavior is not predicted by the theory. For drop volume less than or equal to 15 microL, a succession of two different regimes which depend on the viscosity and surfactant concentration are observed in the following order: a molecular-kinetic regime followed by a hydrodynamic regime (for high viscosity in the presence of surfactant) or a hydrodynamic regime and lastly a final asymptotic regime corresponding to a long relaxation time to equilibrium (for high viscosity in absence of surfactant and for low viscosity regardless of the presence of surfactant). The spreading follows quantitatively the predictions of the theory. Our results demonstrate that the theory is still valid for low viscosity liquids and in the presence of surfactant. The contact angle for which the crossover between molecular-kinetic regime and hydrodynamic regime occurs is thoroughly estimated since the theories do not allow the exact calculation of this value. Here for the first time, an empirical power law exponent (n=0.08+/-0.05) is proposed for

Probing the surface of aqueous surfactant-perfume mixed solutions during perfume evaporation

OpenAIRE

Penfold, J; Thomas, RK; Bradbury, R; Tucker, I; Petkov, JT; Jones, CW; Webster, JRP

2017-01-01

The rate of release or evaporation of perfume molecules from surfaces is a key factor in determining the impact of the perfume in a range of applications relating to home and personal care products. For mixtures of the anionic surfactant sodium dodecylsulfate and the model perfume linalool the rate of change of adsorption with time due to forced air flow over a fixed headspace was evaluated using neutron reflectivity over a period of up to ∼250 min. The measurements were made in the limit of ...

Effects of surfactants on spinning carbon nanotube fibers by an electrophoretic method

Directory of Open Access Journals (Sweden)

Jun Ma, Jie Tang, Qian Cheng, Han Zhang, Norio Shinya and Lu-Chang Qin

2010-01-01

Full Text Available Thin fibers were spun from a colloidal solution of single-walled carbon nanotubes (SWNTs using an electrophoretic method. Sodium dodecylbenzenesulfonate (NaDDBS was chosen as a surfactant and showed good performance owing to its special chemical structure. The highest spinning velocity reached 0.5 mm s−1. The resulting SWNT fibers had a tensile strength of 400 MPa and a conductivity of 355 S cm−1. Their mechanical and electrical properties were markedly improved after adding NaDDBS as the dispersant in water.

Synthesis of low-oxide blue luminescent alkyl-functionalized silicon nanoparticles with no nitrogen containing surfactant

International Nuclear Information System (INIS)

Thomas, Jason A.; Ashby, Shane P.; Huld, Frederik; Pennycook, Timothy J.; Chao, Yimin

2015-01-01

Of ever growing interest in the fields of physical chemistry and materials science, silicon nanoparticles show a great deal of potential. Methods for their synthesis are, however, often hazardous, expensive or otherwise impractical. In the literature, there is a safe, fast and cheap inverse micelle-based method for the production of alkyl-functionalized blue luminescent silicon nanoparticles, which nonetheless found limitations, due to undesirable Si-alkoxy and remaining Si–H functionalization. In the following work, these problems are addressed, whereby an optimisation of the reaction mechanism encourages more desirable capping, and the introduction of alcohol is replaced by the use of anhydrous copper (II) chloride. The resulting particles, when compared with their predecessors through a myriad of spectroscopic techniques, are shown to have greatly reduced levels of ‘undesirable’ capping, with a much lower surface oxide level; whilst also maintaining long-term air stability, strong photoluminescence and high yields

Synthesis of low-oxide blue luminescent alkyl-functionalized silicon nanoparticles with no nitrogen containing surfactant

Energy Technology Data Exchange (ETDEWEB)

Thomas, Jason A.; Ashby, Shane P.; Huld, Frederik [University of East Anglia, School of Chemistry (United Kingdom); Pennycook, Timothy J. [SuperSTEM Laboratory, STFC Daresbury Campus (United Kingdom); Chao, Yimin, E-mail: y.chao@uea.ac.uk [University of East Anglia, School of Chemistry (United Kingdom)

2015-05-15

Of ever growing interest in the fields of physical chemistry and materials science, silicon nanoparticles show a great deal of potential. Methods for their synthesis are, however, often hazardous, expensive or otherwise impractical. In the literature, there is a safe, fast and cheap inverse micelle-based method for the production of alkyl-functionalized blue luminescent silicon nanoparticles, which nonetheless found limitations, due to undesirable Si-alkoxy and remaining Si–H functionalization. In the following work, these problems are addressed, whereby an optimisation of the reaction mechanism encourages more desirable capping, and the introduction of alcohol is replaced by the use of anhydrous copper (II) chloride. The resulting particles, when compared with their predecessors through a myriad of spectroscopic techniques, are shown to have greatly reduced levels of ‘undesirable’ capping, with a much lower surface oxide level; whilst also maintaining long-term air stability, strong photoluminescence and high yields.

Sintesis Asam Etoksi Lignosulfonat sebagai Surfaktan dari Limbah Tandan Kosong Kelapa Sawit

Directory of Open Access Journals (Sweden)

A Ardinal

2017-12-01

Full Text Available Synthesis of ethoxy lignosulfonic acid as a surfactant from a waste of palm oil empty fruit bunch was aimed to isolate lignin, studying the ethylation of the lignin and sulfonation of the alkyl lignin to produce ethoxy lignosulfonic acid moreover to investigate its activity as the surfactant. At first, lignin was isolated from the waste of palm oil empty fruit bunch by sulfate method, then lignin was alkylated with diethylsulfate (DES, and the resulted ethoxy lignin was sulfonated using sodium bisulfite. Each product was characterized by FT-IR and the success of the sulfonation was proven by SEM-EDX. Surfactant test properties included: determination of critical micelle concentration (CMC with turbidimetry method, foam stability, emulsions index and emulsion stability. Lignin isolation gave lignin as light brown solid in 27.8% yield. Alkylation reaction of lignin with diethyl sulfate produced ethoxy lignin in 83.0% yield. Sulfonation of ethoxy lignin using sodium bisulfite afforded ethoxy lignosulfonic acid in 88.5% yield. It was known that there was a significant increase in oxygen percentage at the sulfonation process. Ethoxy lignosulfonic acid as the surfactant has CMC of 1.6 g/L, the surfactant concentration of 1.5 g/L gave stable foam for 100 minutes, the surfactant has an emulsion index of 35% in a gasoline-water system and 56% in the cooking oil-water system. The emulsion on both systems was stable for four days of measurement.ABSTRAKSintesis asam etoksi lignosulfonat sebagai surfaktan dari limbah tandan kosong kelapa sawit (TKKS dilakukan dengan tujuan mengisolasi lignin dari TKKS, mempelajari etilasi terhadap lignin dan sulfonasi terhadap etoksi lignin untuk menghasilkan asam etoksi lignosulfonat serta uji aktifitasnya sebagai surfaktan. Lignin diisolasi dari TKKS dengan metode sulfat, lalu dialkilasi dengan dietil sulfat (DES dan disulfonasi dengan natrium bisulfit. Tiap produk dikarakterisasi dengan FT-IR dan untuk mengetahui

Distribution of methyl and ethyl adducts following alkylation with monofunctional alkylating agents.

Science.gov (United States)

Beranek, D T

1990-07-01

Alkylating agents, because of their ability to react directly with DNA either in vitro or in vivo, or following metabolic activation as in the case of the dialkylnitrosamines, have been used extensively in studying the mechanisms of mutagenicity and carcinogenicity. Their occurrence is widespread in the environment and human exposure from natural and pollutant sources is universal. Since most of these chemicals show varying degrees of both carcinogenicity and mutagenicity, and exhibit compound-specific binding patterns, they provide an excellent model for studying molecular dosimetry. Molecular dosimetry defines dose as the number of adducts bound per macromolecule and relates the binding of these adducts to the human mutagenic or carcinogenic response. This review complies DNA alkylation data for both methylating and ethylating agents in a variety of systems and discusses the role these alkylation products plays in molecular mutagenesis.

Surfactant -- Where Are We in 2003?

Directory of Open Access Journals (Sweden)

JF Lewis

2004-01-01

Full Text Available Surfactant research has progressed over the past several years to the extent that exogenous surfactant administration in patients with the acute respiratory distress syndrome (ARDS is now being evaluated. Unfortunately, clinical responses have been variable, and we now need to take a look at how surfactant is altered in this disease so that more effective treatment strategies can be developed. This review briefly discusses the biophysical and host defense properties of surfactant, the impact of mechanical ventilation (MV on the endogenous surfactant system and the most recent clinical data involving exogenous surfactant administration in patients with ARDS. Discussions regarding future directions of surfactant research both in ARDS and diseases other than acute lung injury are included.