WorldWideScience

Sample records for surfactant sodium dodecyl

  1. sodium dodecyl sulphate (SDS)

    Indian Academy of Sciences (India)

    Unknown

    sodium dodecyl sulphate, SDS) showed a marked effect, although there are some reports where cationic (cetyl trimethyl ammonium bromide, CTAB) and neutral (Triton X-100) surfactants have also shown changes in the. *For correspondence ...

  2. Effect of Anionic Surfactant on the Thermo Acoustical Properties of Sodium Dodecyl Sulphate in Polyvinyl Alcohol Solution by Ultrasonic Method

    Directory of Open Access Journals (Sweden)

    S. Ravichandran

    2011-01-01

    Full Text Available The interaction of sodium dodecyl sulphate (SDS / poly(vinyl alcohol (PVA solution was studied by ultrasonic velocity measurements. Ultrasonic velocity, density, viscosity in mixtures of sodium dodecyl sulphate in polyvinyl alcohol was measured over the entire range of composition. From the experimental data, other related thermodynamic parameters, viz., adiabatic compressibility, intermolecular free length, surface tension, relative association, relaxation time, absorption coefficient and internal pressure were calculated. Formations of rods interfere with velocity of ultrasonic waves. Hence the ultrasonic velocity decreases with concentration. These results were interpreted in terms of polymer-surfactant complex reactions.

  3. A conductometric investigation of hydroxypropylmethyl cellulose/sodium dodecyl sulfate/nonionic surfactant systems

    Directory of Open Access Journals (Sweden)

    Petrović Lidija B.

    2014-01-01

    Full Text Available Surfactant mixtures are very often used in various cosmetic and pharmaceutical products because they commonly act in synergism and provide more favorable properties than the single surfactants. At the same time, the 9 presence of polymers in mixtures of surfactants may lead to molecular interactions thereby affecting product stability and activity. For these reasons it is very important to determine the surfactant interactions influence on 1micellization and mixed micellization, as well as polymer-surfactants mixed micelles interactions. In this work we examined self-aggregation of nonionic surfactants, polysorbate 20 (Tween 20, polyoxyethylene octylphenyl ether (Triton X100 and polyoxyethylene-polyoxypropylene block copolymer (Pluronic F68 with ionic surfactant, sodium dodecylsulfate, in aqueous solution at 40ºC using conductometric titration method. It was found that concentration region for mixed micelle formation depends on nonionic surfactant characteristics and its concentration. Formation of surfactants mixed micelles in the presence of nonionic polymer, hydroxypropylmethyl cellulose, and their binding to polymer hydrophobic sites, were investigated too. Analysis of obtained results points to different kinds of interactions in investigated systems, which are crucial for their application. [Projekat Ministarstva nauke Republike Srbije, br. III 46010

  4. Thermodynamic solution properties of pefloxacin mesylate and its interactions with organized assemblies of anionic surfactant, sodium dodecyl sulphate

    International Nuclear Information System (INIS)

    Usman, Muhammad; Rashid, Muhammad Abid; Mansha, Asim; Siddiq, Mohammad

    2013-01-01

    Graphical abstract: - Highlights: • Free energy of adsorption is more negative than free energy of micellization. • Micellization becomes more spontaneous at high temperature. • There is strong interaction between PFM and SDS. - Abstract: This manuscript reports the physicochemical behavior of antibiotic amphiphilic drug pefloxacin mesylate (PFM) and its interaction with anionic surfactant, sodium dodecyl sulfate (SDS). The data of surface tension and electrical conductivity are helpful to detect the CMC as well as to calculate surface parameters, i.e. surface pressure, π, surface excess concentration, Γ, area per molecule of drug and standard Gibbs free energy of adsorption, ΔG ads and thermodynamic parameters like standard free energy of micellization, ΔG m , standard enthalpy of micellization, ΔH m and standard entropy of micellization, ΔS m . The interaction of this drug with anionic surfactant, sodium dodecyl sulfate (SDS) was studied by electrical conductivity and UV/visible spectroscopy. This enabled us to compute the values of partition coefficient (K x ), free energy of partition, ΔG p , binding constant, K b , free energy of binding, ΔG b , number of drug molecules per micelle, n, and thermodynamic parameters of drug–surfactant interaction

  5. Impact of model perfume molecules on the self-assembly of anionic surfactant sodium dodecyl 6-benzene sulfonate.

    Science.gov (United States)

    Bradbury, Robert; Penfold, Jeffrey; Thomas, Robert K; Tucker, Ian M; Petkov, Jordan T; Jones, Craig; Grillo, Isabelle

    2013-03-12

    The impact of two model perfumes with differing degrees of hydrophobicity/hydrophilicity, linalool (LL) and phenylethanol (PE), on the solution structure of anionic surfactant sodium dodecyl 6-benzene sulfonate, LAS-6, has been studied by small angle neutron scattering, SANS. For both types of perfume molecules, complex phase behavior is observed. The phase behavior depends upon the concentration, surfactant/perfume composition, and type of perfume. The more hydrophilic perfume PE promotes the formation of more highly curved structures. At relatively low surfactant concentrations, small globular micelles, L1, are formed. These become perfume droplets, L(sm), stabilized by the surfactant at much higher perfume solution compositions. At higher surfactant concentrations, the tendency of LAS-6 to form more planar structures is evident. The more hydrophobic linalool promotes the formation of more planar structures. Combined with the greater tendency of LAS-6 to form planar structures, this results in the planar structures dominating the phase behavior for the LAS-6/linalool mixtures. For the LAS-6/linalool mixture, the self-assembly is in the form of micelles only at the lowest surfactant and perfume concentrations. Over most of the concentration-composition space explored, the structures are predominantly lamellar, L(α), or vesicle, L(v), or in the form of a lamellar/micellar coexistence. At low and intermediate amounts of LL, a significantly different structure is observed, and the aggregates are in the form of small, relatively monodisperse vesicles (i.e., nanovesicles), L(sv).

  6. Micellar solubilization in strongly interacting binary surfactant systems. [Binary surfactant systems of: dodecyltrimethylammonium chloride + sodium dodecyl sulfate; benzyldimethyltetradecylammonium chloride + tetradecyltrimethylammonium chloride

    Energy Technology Data Exchange (ETDEWEB)

    Treiner, C. (Universite Pierre et Marie Curie, Paris (France)); Nortz, M.; Vaution, C. (Faculte de Pharmacie de Paris-sud, Chatenay-Malabry (France))

    1990-07-01

    The apparent partition coefficient P of barbituric acids between micelles and water has been determined in mixed binary surfactant solutions from solubility measurements in the whole micellar composition range. The binary systems chosen ranged from the strongly interacting system dodecyltrimethylammonium chloride + sodium dodecyl sulfate to weakly interacting systems such as benzyldimethyltetradecylammonium chloride + tetradecyltrimethyammonium chloride. In all cases studied, mixed micelle formation is unfavorable to micellar solubilization. A correlation is found between the unlike surfactants interaction energy, as measured by the regular solution parameter {beta} and the solute partition coefficient change upon surfactant mixing. By use of literature data on micellar solubilization in binary surfactant solutions, it is shown that the change of P for solutes which are solubilized by surface adsorption is generally governed by the sign and amplitude of the interaction parameter {beta}.

  7. Occurrence of photoluminescence and onion like structures decorating graphene oxide with europium using sodium dodecyl sulfate surfactant

    Science.gov (United States)

    Cedeño, V. J.; Rangel, R.; Cervantes, J. L.; Lara, J.; Alvarado, J. J.; Galván, D. H.

    2017-07-01

    Graphene oxide decoration with europium was carried out using SDS (sodium dodecyl sulfate) as the surfactant. The reaction was performed in a microwave oven and subsequently underwent thermal treatment under hydrogen flow. The results found in the present work demonstrate that through the use of SDS surfactant aggregates of hemi-cylindrical and onion-like structures could be obtained; which propitiate an enhanced synergistic photoluminescence located at the red wavelength. On the other hand, after thermal treatment the aggregates disappear providing a good dispersion of europium, however a decrease in the photoluminescence signal is observed. The graphene oxide decorated with europium was characterized by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), Fourier infrared transform spectroscopy (FTIR), RAMAN spectroscopy, x-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM) techniques, showing the characteristic features of graphene oxide and europium.

  8. Adsorption of hydroxamate siderophores and EDTA on goethite in the presence of the surfactant sodium dodecyl sulfate

    Directory of Open Access Journals (Sweden)

    Xu Jide

    2009-06-01

    Full Text Available Abstract Siderophore-promoted iron acquisition by microorganisms usually occurs in the presence of other organic molecules, including biosurfactants. We have investigated the influence of the anionic surfactant sodium dodecyl sulfate (SDS on the adsorption of the siderophores DFOB (cationic and DFOD (neutral and the ligand EDTA (anionic onto goethite (α-FeOOH at pH 6. We also studied the adsorption of the corresponding 1:1 Fe(III-ligand complexes, which are products of the dissolution process. Adsorption of the two free siderophores increased in a similar fashion with increasing SDS concentration, despite their difference in molecule charge. In contrast, SDS had little effect on the adsorption of EDTA. Adsorption of the Fe-DFOB and Fe-DFOD complexes also increased with increasing SDS concentrations, while adsorption of Fe-EDTA decreased. Our results suggest that hydrophobic interactions between adsorbed surfactants and siderophores are more important than electrostatic interactions. However, for strongly hydrophilic molecules, such as EDTA and its iron complex, the influence of SDS on their adsorption seems to depend on their tendency to form inner-sphere or outer-sphere surface complexes. Our results demonstrate that surfactants have a strong influence on the adsorption of siderophores to Fe oxides, which has important implications for siderophore-promoted dissolution of iron oxides and biological iron acquisition.

  9. Ecotoxicological assessment of the pharmaceutical fluoxetine hydrochloride and the surfactant dodecyl sodium sulfate after their submission to ionizing radiation treatment

    International Nuclear Information System (INIS)

    Santos, Dymes Rafael Alves dos

    2011-01-01

    The use of pharmaceuticals and personal care products and the consequent and continuous input of this substances in the environment generates an increasing need to investigate the presence, behavior and the effects on aquatic biota, as well as new ways to treat effluents containing such substances. Fluoxetine hydrochloride is an active ingredient used in the treatment of depressive disorders and anxiety. As the surfactant sodium dodecyl sulfate is present in many cleaning and personal care products. The present study aimed on assessing the acute toxicity of fluoxetine hydrochloride, sodium dodecyl sulfate and the mixture of both to the aquatic organisms Hyalella azteca, Daphnia similis and Vibrio ficheri. Reducing the toxicity of fluoxetine and the mixture after treatment with ionizing radiation from industrial electron beam accelerator has also been the focus of this study. For Daphnia similis the average values of CE50-4 8h found for the non-irradiated drug, surfactant and mixture were 14.4 %, 9.62 % and 13.8 %, respectively. After irradiation of the substances, the dose 5 kGy proved itself to be the most effective dose for the treatment of the drug and the mixture as it was obtained the mean values for CE50 48h 84.60 % and > 90 %, respectively. For Hyalella azteca the acute toxicity tests were performed for water column with duration of 96 hours, the mean values for CE50 96h found for the drug, the surfactant and the mixture non-irradiated were 5.63 %, 19.29 %, 6.27 %, respectively. For the drug fluoxetine and the mixture irradiated with 5 kGy, it was obtained 69.57 % and 77.7 %, respectively. For Vibrio ficheri the acute toxicity tests for the untreated drug and the drug irradiated with 5 kGy it was obtained CE50 15min of 6.9 % and 32.88 % respectively. These results presented a reduction of the acute toxicity of the test-substances after irradiation. (author)

  10. Effect of different concentrations of sodium dodecyl sulfate and additional anionic surfactant on properties of low protein natural rubber latex

    Science.gov (United States)

    Abdullah, Nurulhuda; Manaf, Siti Nor Qamarina; Hassan, Aziana Abu

    2017-12-01

    This paper describes the chemical deproteinization process of natural rubber latex (NRL) using chemical denaturants namely urea and sodium dodecyl sulfate (SDS). Commercial high ammoniated natural rubber latex (HANRL) was incubated with both denaturants - urea and SDS for selected period of time before centrifugation and characterization. The role of SDS in NRL deproteinization process was further elucidated by manipulating the concentration of SDS at 0.3 phr and 0.5 phr during the incubation process. It was found that the physical properties of NRL especially stability, were governed by the amount of SDS, whereby higher concentration of SDS used led to greater NRL stability. However, too much concentration of SDS in the system might cause detrimental effect on the properties of low protein NRL. The effects of additional anionic surfactant namely potassium laurate on the physical properties of low protein NRL and its stabilization were also scrutinized. Characterizations include nitrogen determination by Kjeldahl method, zeta potential, and morphological analysis by Field Emission Scanning Electron Microscopy (FESEM).

  11. Polyelectrolyte-surfactant complexes formed by poly[3,5-bis(trimethylammoniummethyl)4-hydroxystyrene iodide]-block-poly(ethylene oxide) and sodium dodecyl sulfate in aqueous solutions

    Czech Academy of Sciences Publication Activity Database

    Štěpánek, M.; Matějíček, P.; Procházka, K.; Filippov, Sergey K.; Angelov, Borislav; Šlouf, Miroslav; Mountrichas, G.; Pispas, S.

    2011-01-01

    Roč. 27, č. 9 (2011), s. 5275-5281 ISSN 0743-7463 R&D Projects: GA MŠk ME09059; GA ČR GCP205/11/J043; GA ČR GAP208/10/0353 Institutional research plan: CEZ:AV0Z40500505 Keywords : polyelectrolyte-surfactant complexes * sodium dodecyl sulfate * small-angle X-ray scattering Subject RIV: CD - Macromolecular Chemistry Impact factor: 4.186, year: 2011

  12. Contribution of sodium dodecyl sulphate and sodium lauric acid in ...

    Indian Academy of Sciences (India)

    Contribution of sodium dodecyl sulphate and sodium lauric acid in the one-pot synthesis of intercalated ... chain length but different anion groups were used together as intercalates to prepare intercalated ZnAl–layered double hydroxides ... assembly method, LDHs layers and surfactants are closely interconnected.

  13. Contribution of sodium dodecyl sulphate and sodium lauric acid in ...

    Indian Academy of Sciences (India)

    Abstract. Anion surfactants, sodium dodecyl sulphate (SDS) and sodium lauric acid (SLA), with almost the same chain length but different anion groups were used together as intercalates to prepare intercalated ZnAl–layered double hydroxides (ZnAl–LDHs). Their composition, structure and morphology were characterized ...

  14. Conductometric study of sodium dodecyl sulfate - nonionic surfactant (Triton X-100, Tween 20, Tween 60, Tween 80 or Tween 85 mixed micelles in aqueous solution

    Directory of Open Access Journals (Sweden)

    Ćirin Dejan M.

    2012-01-01

    Full Text Available The present study is concerned with the determination of the critical micelle concentration (cmc of mixed micelles of sodium dodecyl sulfate with one of five nonionic surfactants (Triton X-100, Tween 20, Tween 60, Tween 80 or Tween 85 from conductance measurements. Based on the calculated values of the β parameters we have noticed that SDS-nonionic surfactants mostly showed strong synergistic effect. It was found that nonionic surfactants with mainly longer and more hydrophobic tail show stronger interactions with hydrophobic part of SDS, thus expressing stronger synergism. In SDS-Tween 80 binary system the strongest synergistic effect was noticed. SDS-Tween 85 micellar system showed antagonistic effect, most probably because the presence of the double bond in its three hydrophobic tails (three C18 tails makes it sterically rigid.

  15. sodium dodecyl sulphate (SDS)

    Indian Academy of Sciences (India)

    Unknown

    Addition of NaCl during the dye–surfactant complex formation converted the complex into ... homogeneous aqueous system, the photochemical devices show very poor power- conversion efficiency due to slow ... reactions in a suitable micellar media.4 Cresyl violet, a phenoxazine dye is of current interest particularly for ...

  16. Interactions between poly(acrylic acid) and sodium dodecyl sulfate: isothermal titration calorimetric and surfactant ion-selective electrode studies.

    Science.gov (United States)

    Wang, C; Tam, K C

    2005-03-24

    Interaction between a monodispersed poly(acrylic acid) (PAA) (M(W) = 5670 g/mol, M(w)/M(n) = 1.02) with sodium dodecyl sulfate (SDS) was investigated using isothermal titration calorimetry (ITC), ion-selective electrode (ISE), and dynamic light scattering measurements. Contrary to previous studies, we report for the first time evidence of interaction between SDS and PAA when the degree of neutralization (alpha) of PAA is lower than 0.2. Hydrocarbon chains of SDS cooperatively bind to apolar segments of PAA driven by hydrophobic interaction. The interaction is both enthalpy and entropy favored (deltaH is negative but deltaS is positive). In 0.05 wt % PAA solution, the SDS concentration corresponding to the onset of binding (i.e., CAC) is approximately 2.4 mM and the saturation concentration (i.e., C(S)) is approximately 13.3 mM when alpha = 0. When PAA was neutralized and ionized, the binding was hindered by the enhanced electrostatic repulsion between negatively charged SDS and PAA chains and improved solubility of the polymer. With increasing alpha to 0.2, CAC increases to approximately 6.2 mM, C(S) drops to 8.6 mM, and the interaction is significantly weakened where the amount of bound SDS on PAA is reduced considerably. The values of CAC and C(S) derived from different techniques are in good agreement. The binding results in the formation of mixed micelles on apolar PAA coils, which then expands and dissociates into single PAA chains. The majority of unneutralized PAA molecules exist as single polymer chains stabilized by bound SDS micelles in solution after the saturation concentration.

  17. Coarse-Grain Molecular Dynamics Simulations to Investigate the Bulk Viscosity and Critical Micelle Concentration of the Ionic Surfactant Sodium Dodecyl Sulfate (SDS) in Aqueous Solution.

    Science.gov (United States)

    Ruiz-Morales, Yosadara; Romero-Martínez, Ascencion

    2018-03-13

    The first critical micelle concentration (CMC) of the ionic surfactant sodium dodecyl sulfate (SDS), in diluted aqueous solution, has been determined at room temperature from the investigation of the bulk viscosity, at several concentrations of SDS, by means of coarse grain molecular dynamics simulations. The coarse-grained model molecules at the mesoscale level are adopted. The bulk viscosity of SDS was calculated at several millimolar concentrations of SDS in water using the MARTINI force field by means of NVT shear Mesocite molecular dynamics. The definition of each bead in the MARTINI force field is established, as well as their radius, volume, and mass. The effect of the size of the simulation box on the obtained CMC has been investigated as well as the effect of the number of SDS molecules, in the simulations, on the formation of aggregates. The CMC, which was obtained from a graph of the calculated viscosities versus concentration, is in good agreement with reported experimental data, and do not depend on the size of the box used in the simulation. The formation of a spherical micelle-like aggregate is observed, where the dodecyl sulfate tails point inwards and the heads point outwards the aggregation micelle, in accordance with experimental observations. The advantage of using coarse grain molecular dynamics is the possibility of treating explicitly charged beads, applying a shear flow for viscosity calculation, as well as to process much larger spatial and temporal scales than atomistic molecular dynamics can. Furthermore, the CMC of SDS obtained with the coarse-grained model is in much better agreement with the experimental value than the value obtained with atomistic simulations.

  18. Estimation of interfacial acidity of sodium dodecyl sulfate micelles

    Indian Academy of Sciences (India)

    An enhancement in the excited state proton transfer (ESPT) processes of coumarin-102 (C-102) dye was observed upon addition of salicylic acid and hydrochloric acid in sodium dodecyl sulfate (SDS) micellar solution. The phenomenon was observed only in the micellar medium of anionic surfactant SDS and not in case of ...

  19. Estimation of interfacial acidity of sodium dodecyl sulfate micelles

    Indian Academy of Sciences (India)

    Abstract. An enhancement in the excited state proton transfer (ESPT) processes of coumarin-102 (C-102) dye was observed upon addition of salicylic acid and hydrochloric acid in sodium dodecyl sulfate (SDS) micellar solution. The phenomenon was observed only in the micellar medium of anionic surfactant SDS and.

  20. Impact of sodium dodecyl sulphate on the dissolution of poorly soluble drug into biorelevant medium from drug-surfactant discs

    DEFF Research Database (Denmark)

    Madelung, Peter; Ostergaard, Jesper; Bertelsen, Poul

    2014-01-01

    soluble drugs griseofulvin and felodipine in a biorelevant dissolution medium (BDM). Dissolution constants from dissolution profiles of drug discs with and without SDS were measured using miniaturized rotating disc dissolution. Solid state changes were investigated by X-ray diffraction. Solubility...... was determined using HPLC-UV. The interaction between micelles in BDM and SDS was investigated by isothermal titration calorimetry and dynamic light scattering. Isothermal titration calorimetry showed that SDS formed mixed micelles with bile salt:phospholipid (BS:PC) micelles in BDM. Dynamic light scattering....... The improved solubility at the solid-liquid interface provided a much steeper concentration gradient resulted in a faster dissolution. The total amount of SDS in the discs only gave a minor increase in total surfactant concentration in the dissolution medium and did therefore not to any large extent affect...

  1. Sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS ...

    African Journals Online (AJOL)

    Four strains of eri, Samia cynthia ricini Lepidoptera: Saturniidae that can be identified morphologically and maintained at North East Institute of Science and Technology, Jorhat were characterized based on their protein profile by sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE) and DNA by random ...

  2. Interfacial properties of chitosan/sodium dodecyl sulfate complexes

    Directory of Open Access Journals (Sweden)

    Milinković Jelena R.

    2017-01-01

    Full Text Available Contemporary formulations of cosmetic and pharmaceutical emulsions may be achieved by using combined polymer/surfactant system, which can form complexes with different structure and physicochemical properties. Such complexation can lead to additional stabilization of the emulsion products. For these reasons, the main goal of this study was to investigate the interfacial properties of chitosan/sodium dodecyl sulfate complexes. In order to understand the stabilization mechanism, the interface of the oil/water systems that contained mixtures of chitosan and sodium dodecyl sulfate, was studied by measuring the interfacial tension. Considering the fact that the properties of the oil phase has influence on the adsorption process, three different types of oil were investigated: medium-chain triglycerides (semi-synthetic oil, paraffin oil (mineral oil and natural oil obtained from the grape seed. The surface tension measurements at the oil/water interface, for chitosan water solutions, indicate a poor surface activity of this biopolymer. Addition of sodium dodecyl sulfate to chitosan solution causes a significant decrease in the interfacial tension for all investigated oils. The results of this study are important for understanding the influence of polymer-surfactant interactions on the properties of the solution and stability of dispersed systems. [Project of the Serbian Ministry of Education, Science and Technological Development, Grant no. III46010

  3. Adsorption of sodium dodecyl sulfate and sodium dodecyl phosphate on aluminum, studied by QCM-D, XPS, and AAS.

    Science.gov (United States)

    Karlsson, Philip M; Palmqvist, Anders E C; Holmberg, Krister

    2008-12-02

    The adsorption of two anionic surfactants, sodium dodecyl sulfate (SDS) and sodium dodecyl phosphate (SDP), at surfaces of aluminum and aluminum oxide has been studied by means of atomic absorption spectrometry (AAS), X-ray photoelectron spectroscopy (XPS), and quartz crystal microbalance with dissipation monitoring (QCM-D). It was shown that more SDP than SDS binds to the surface and that SDP prevents dissolution of aluminum in water whereas SDS does not. This was not obvious, since the adsorption isotherms of the two surfactants to aluminum pigment powder are quite similar, as shown in an earlier work. The decreased aluminum dissolution with SDP compared to SDS was explained by the formation of a more compact protective layer with less permeability on the aluminum surface with SDP than with SDS. This is explained by differences in complexing ability between the surfactants and the aluminum pigment surface. While SDP is expected to form an inner-sphere complex with aluminum, leading to a lower accessibility of aluminum sites to water, SDS is likely to form a weaker outer-sphere complex.

  4. Hair protein removal by sodium dodecyl sulfate.

    Science.gov (United States)

    de Cássia Comis Wagner, Rita; Joekes, Inés

    2005-03-10

    The effect of sodium dodecyl sulfate (SDS) on protein loss was studied. Three kinds of human hair were tested by rubbing or immersion in water or immersion in SDS solution, at 25, 40 and 70 degrees C. Under friction, hair treated with SDS solution loses seven times more protein than in water, while by immersion, protein loss is roughly two times higher in SDS than in water. Protein loss increases at higher temperatures. Estimated activation energy values for protein loss by immersion are 69+/-22 kJ mol(-1) for blended brown hair; 40+/-12 kJ mol(-1) for blond hair (tip-end region) and 61+/-4 kJ mol(-1) for blond hair (root-end region) for samples treated in water, while 53+/-8, 7+/-5 and 32+/-8 kJ mol(-1) were the corresponding activation energy values for samples treated in 5% SDS solution. These values indicate that protein loss is mainly a diffusion-controlled process. The more damaged the hair, the lower the activation energy and the higher the protein loss. From these data, it can be estimated that daily care shampooing at room temperature will cause opacity and combing difficulties in 1 year and split ends after 3 years by removal of all cuticle layers.

  5. Effects of sodium dodecyl sulfate of polyphenoloxidase

    International Nuclear Information System (INIS)

    Moore, B.M.; Flurkey, W.H.

    1989-01-01

    The effects of sodium dodecyl sulfate (SDS) on the enzymatic and physical characteristics of purified broad bean polyphenoloxidase (PPO) were examined. A sigmoidal increase in PPO activation was observed with increasing SDS concentrations. Half maximal activation occurred at .9 mM SDS well below the CMC of 3.5 mM. No apparent changes in the Km for catechol, pH optimum, of I 50 for tropolone were observed in the presence vs absence of SDS. Thermal inactivation and binding of 14 C dopa increased in the presence of SDS. Analytical ultracentrifugation and HPLC-SEC indicated that SDS did not change the apparent size of the PPO under nondenaturing conditions. Scanning fluorescence spectroscopy showed an increase in intrinsic trp/tyr fluorescence at approximately the same concentration in which SDS activation began. Further addition of SDS caused a large increase in intrinsic fluorescence. These results suggest the SDS causes an apparent conformational change induced by SDS binding which leads to enzyme activation

  6. Towards optimised drug delivery: structure and composition of testosterone enanthate in sodium dodecyl sulfate monolayers.

    Science.gov (United States)

    Saaka, Yussif; Allen, Daniel T; Luangwitchajaroen, Yuvared; Shao, Yanan; Campbell, Richard A; Lorenz, Christian D; Lawrence, M Jayne

    2018-04-09

    Surface tension and specular neutron reflectivity measurements have been used, for the first time to systematically study both the interfacial structure and composition of monolayers of the soluble surfactant, sodium dodecyl sulfate containing a low-dose, poorly water soluble drug, testosterone enanthate. Modelling of the specular neutron reflectivity data suggests that the hydrophobic testosterone enanthate was adsorbed in the C12 hydrophobic tail region of the surfactant monolayer, regardless of the concentration of surfactant at the interface and whether or not additional drug was added to the interface. The location of the hydrophobic drug in the tail region of the surfactant monolayer is supported by the results of classical, large-scale molecular dynamics simulations. The thickness of the surfactant monolayer obtained, in the presence and absence of drug, using molecular dynamics simulations was in good agreement with the corresponding values obtained from the specular neutron reflectivity measurements. The stoichiometry of surfactant:drug at the air-water interface at sodium dodecyl sulfate concentrations above the critical micelle concentration was determined from specular neutron reflectivity measurements to be approximately 3 : 1, and remained constant after the spreading of further testosterone enanthate at the interface. Significantly, this stoichiometry was the same as that obtained in the micelles from bulk solubilisation studies. Important insights into the preferred location of drug in surfactant monolayers at the air-water interface as well as its effect on the structure of the monolayer have been obtained from our combined use of experimental and simulation techniques.

  7. Pathway for Unfolding of Ubiquitin in Sodium Dodecyl Sulfate, Studied by Capillary Electrophoresis

    OpenAIRE

    Schneider, Grégory F.; Shaw, Bryan F.; Lee, Andrew; Carillho, Emanuel; Whitesides, George M.

    2008-01-01

    This paper characterizes the complexes formed by a small protein, ubiquitin (UBI), and a negatively charged surfactant, sodium dodecyl sulfate (SDS), using capillary electrophoresis (CE), circular dichroism (CD), and amide hydrogendeuterium exchange (HDX; as monitored by mass spectroscopy, MS). Capillary electrophoresis of complexes of UBI and SDS, at apparent equilibrium, at concentrations of SDS ranging from sub-micellar and sub-denaturing to micellar and denaturing, revealed multiple compl...

  8. Immobilization of surface active compounds on polymer supports using glow discharge processess. 1. Sodium dodecyl sulfate on poly(propylene)

    NARCIS (Netherlands)

    Terlingen, J.G.A.; Terlingen, Johannes G.A.; Feijen, Jan; Hoffman, Allan S.

    1993-01-01

    A new method has been developed in which a reversibly adsorbed layer of a surfactant (sodium dodecyl sulfate, SDS) is covalently immobilized in one step onto a hydrophobic substrate (poly(propylene), PP) by applying an argon plasma treatment. The adsorption of SDS from aqueous solutions onto PP

  9. Epidermal cell proliferation and terminal differentiation in skin organ culture after topical exposure to sodium dodecyl sulphate

    NARCIS (Netherlands)

    Sandt, J.J.M. van de; Bos, T.A.; Rutten, A.A.J.J.L.

    1995-01-01

    Epidermal cell proliferation and differentiation were investigated in vitro after exposure to the anionic surfactant sodium dodecyl sulfate (SDS). Human skin organ cultures were exposed topically to various concentrations of SDS for 22 h, after which the irritant was removed. Cell proliferation was

  10. Anaerobic degradation of sodium dodecyl sulfate (SDS) by denitrifying bacteria

    NARCIS (Netherlands)

    Paulo, A.; Plugge, C.M.; Garcia Encina, P.A.; Stams, A.J.M.

    2013-01-01

    Two denitrifying bacteria were isolated using sodium dodecyl sulfate (SDS) as substrate. Strains SN1 and SN2 were isolated from an activated sludge reactor of a wastewater treatment plant (WWTP) with Anaerobic–Anoxic–Oxic (A2/O) steps. Based on 16S rRNA gene analysis strain SN1 is 99% similar to

  11. Sodium-dodecyl-sulphate-assisted synthesis of Ni nanoparticles ...

    Indian Academy of Sciences (India)

    Stabilized nickel nanoparticles (SNNPs) were prepared using Ni(acac) 2 (acac = acetylacetonate) via a simplesolvothermal method. The synthesis of the nickel nanoparticles was performed in the presence of sodium dodecyl sulphate(SDS) of different concentrations (mole ratios of SDS:Ni(acac) 2 = 1:1, 2:1 and 4:1), as the ...

  12. Sodium-dodecyl-sulphate-assisted synthesis of Ni nanoparticles ...

    Indian Academy of Sciences (India)

    2017-11-20

    Nov 20, 2017 ... The synthesis of the nickel nanoparticles was performed in the presence of sodium dodecyl sulphate. (SDS) of different concentrations ... fields of chemical catalysis, rechargeable batteries, catalysis superconductors, magnetic ..... polar group in SDS arrangement and Ni2+ ions were obtained, with the ...

  13. Sodium-dodecyl-sulphate-assisted synthesis of Ni nanoparticles ...

    Indian Academy of Sciences (India)

    2017-11-20

    Nov 20, 2017 ... Abstract. Stabilized nickel nanoparticles (SNNPs) were prepared using Ni(acac)2 (acac = acetylacetonate) via a simple solvothermal method. The synthesis of the nickel nanoparticles was performed in the presence of sodium dodecyl sulphate. (SDS) of different concentrations (mole ratios of SDS:Ni(acac)2 ...

  14. Intercalation and Exfoliation of Kaolinite with Sodium Dodecyl Sulfate

    Directory of Open Access Journals (Sweden)

    Xiaochao Zuo

    2018-03-01

    Full Text Available Kaolinite (Kaol was intercalated with dimethyl sulfoxide (DMSO and subsequently methanol (MeOH to prepare intercalation compounds Kaol-DMSO and Kaol-MeOH. Kaol-MeOH was used as an intermediate to synthesize Kaol-sodium dodecyl sulfate (SDS intercalation compound (Kaol-SDS via displacement reaction. The ultrasonic exfoliation of Kaol-SDS produced a resultant Kaol-SDS-U. The samples were characterized by X-ray diffraction (XRD, Fourier transformation infrared spectroscopy (FTIR, thermal analysis, scanning electronic microscopy (SEM, transmission electron microscopy (TEM and particle size analysis. The results revealed that the intercalation of sodium dodecyl sulfate into kaolinite layers caused an obvious increase of the basal spacing from 0.72–4.21 nm. The dehydroxylation temperature of Kaol-SDS was obviously lower than that of original kaolinite. During the intercalation process of sodium dodecyl sulfate, a few kaolinite layers were exfoliated and curled up from the edges of the kaolinite sheets. After sonication treatment, the kaolinite layers were further transformed into nanoscrolls, and the exfoliated resultant Kaol-SDS-U possessed a smaller particle size close to nanoscale.

  15. An investigation of chitosan and sodium dodecyl sulfate interactions in acetic media

    Directory of Open Access Journals (Sweden)

    Petrović Lidija B.

    2016-01-01

    Full Text Available Polymer/surfactant association is a cooperative phenomenon where surfactant binds to the polymer in the form of aggregates, usually through electrostatic or hydrophobic forces. As already known, polyelectrolytes may interact with oppositely charged surfactants through electrostatic attraction that results in polymer/surfactant complex formation. This behavior could be desirable in wide range of application of polymer/surfactant mixtures, such as improving colloid stability, gelling, emulsification and microencapsulation. In the present study surface tension, turbidity, viscosity and electrophoretic mobility measurements were used to investigate interactions of cationic polyelectrolyte chitosan (Ch and oppositely charged anionic surfactant, sodium dodecyl sulfate (SDS, in buffered water. Obtained results show the presence of interactions that lead to Ch/SDS complexes formation at all investigated pH and for all investigated polymer concentrations. Mechanisms of interaction, as well as characteristics of formed Ch/SDS complexes, are highly dependent on their mass ratio in the mixtures, while pH has no significant influence. [Projekat Ministarstva nauke Republike Srbije, br. II46010

  16. Spectroscopy and computational studies on the interaction of octyl, dodecyl, and hexadecyl derivatives of anionic and cationic surfactants with adenosine deaminase.

    Science.gov (United States)

    Ajloo, Davood; Mahmoodabadi, Najmeh; Ghadamgahi, Maryam; Saboury, Ali Akbar

    2016-07-01

    Effects of sodium (octyl, dodecyl, hexadecyl) sulfate and their cationic analogous on the structure of adenosine deaminase (ADA) were investigated by fluorescence and circular dichroism spectroscopy as well as molecular dynamics simulation and docking calculation. Root-mean-square derivations, radius of gyration, solvent accessible surface area, and radial distribution function were obtained. The results showed that anionic and cationic surfactants reduce protein stability. Cationic surfactants have more effect on the ADA structure in comparison with anionic surfactants. More concentration and longer surfactants are parallel to higher denaturation. Furthermore, aggregation in the presence of anionic surfactants is more than cationic surfactants. Docking data showed that longer surfactants have more interaction energy and smaller ones bound to the active site.

  17. Ecotoxicological assessment of the pharmaceutical fluoxetine hydrochloride and the surfactant dodecyl sodium sulfate after their submission to ionizing radiation treatment; Avaliacao ecotoxicologica do farmaco cloridrato de fluoxetina e do surfactante dodecil sulfato de sodio quando submetidos a tratamento por radiacao ionizante

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Dymes Rafael Alves dos

    2011-07-01

    The use of pharmaceuticals and personal care products and the consequent and continuous input of this substances in the environment generates an increasing need to investigate the presence, behavior and the effects on aquatic biota, as well as new ways to treat effluents containing such substances. Fluoxetine hydrochloride is an active ingredient used in the treatment of depressive disorders and anxiety. As the surfactant sodium dodecyl sulfate is present in many cleaning and personal care products. The present study aimed on assessing the acute toxicity of fluoxetine hydrochloride, sodium dodecyl sulfate and the mixture of both to the aquatic organisms Hyalella azteca, Daphnia similis and Vibrio ficheri. Reducing the toxicity of fluoxetine and the mixture after treatment with ionizing radiation from industrial electron beam accelerator has also been the focus of this study. For Daphnia similis the average values of CE50-4{sub 8h} found for the non-irradiated drug, surfactant and mixture were 14.4 %, 9.62 % and 13.8 %, respectively. After irradiation of the substances, the dose 5 kGy proved itself to be the most effective dose for the treatment of the drug and the mixture as it was obtained the mean values for CE50{sub 48h} 84.60 % and > 90 %, respectively. For Hyalella azteca the acute toxicity tests were performed for water column with duration of 96 hours, the mean values for CE50{sub 96h} found for the drug, the surfactant and the mixture non-irradiated were 5.63 %, 19.29 %, 6.27 %, respectively. For the drug fluoxetine and the mixture irradiated with 5 kGy, it was obtained 69.57 % and 77.7 %, respectively. For Vibrio ficheri the acute toxicity tests for the untreated drug and the drug irradiated with 5 kGy it was obtained CE50{sub 15min} of 6.9 % and 32.88 % respectively. These results presented a reduction of the acute toxicity of the test-substances after irradiation. (author)

  18. Beyond the detergent effect: a binding site for sodium dodecyl sulfate (SDS) in mammalian apoferritin

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Renyu, E-mail: renyu.liu@uphs.upenn.edu; Bu, Weiming; Xi, Jin [University of Pennsylvania, Philadelphia, Pennsylvania (United States); Mortazavi, Shirin R. [Drexel University College of Medicine, Philadelphia, Pennsylvania (United States); Cheung-Lau, Jasmina C.; Dmochowski, Ivan J. [University of Pennsylvania, Philadelphia, Pennsylvania (United States); Loll, Patrick J., E-mail: renyu.liu@uphs.upenn.edu [Drexel University College of Medicine, Philadelphia, Pennsylvania (United States); University of Pennsylvania, Philadelphia, Pennsylvania (United States)

    2012-05-01

    Using X-ray crystallography and isothermal titration calorimetry, we show that sodium dodecyl sulfate (SDS) binds specifically to a pre-formed internal cavity in horse-spleen apoferritin. Although sodium dodecyl sulfate (SDS) is widely used as an anionic detergent, it can also exert specific pharmacological effects that are independent of the surfactant properties of the molecule. However, structural details of how proteins recognize SDS are scarce. Here, it is demonstrated that SDS binds specifically to a naturally occurring four-helix bundle protein: horse apoferritin. The X-ray crystal structure of the apoferritin–SDS complex was determined at a resolution of 1.9 Å and revealed that the SDS binds in an internal cavity that has previously been shown to recognize various general anesthetics. A dissociation constant of 24 ± 9 µM at 293 K was determined by isothermal titration calorimetry. SDS binds in this cavity by bending its alkyl tail into a horseshoe shape; the charged SDS head group lies in the opening of the cavity at the protein surface. This crystal structure provides insights into the protein–SDS interactions that give rise to binding and may prove useful in the design of novel SDS-like ligands for some proteins.

  19. Influence of sodium dodecyl sulfate on the reaction between Nile Blue A and hydrogen peroxide

    Directory of Open Access Journals (Sweden)

    IVANA A. JANKOVIC

    1999-05-01

    Full Text Available The influence of the anionic surfactant sodium dodecyl sulfate on the rate of the reaction between the cationic form of Nile Blue A and hydrogen peroxide was investigated in the pH range from 5 to 8.5. A retardation of the oxidation of Nile Blue A with hydrogen peroxide of three orders of magnitude was observed at pH 8.5 in the presence of anionic micelles compared to the kinetic data in water. The retardation effect was less pronounced at lower pH values. These effects were explained by the electrostatic interaction of the species involved in the reaction with the negatively charged micellar surface and their effective separation in the vicinity of the micellar surface.

  20. Binding of heavy metals to derivatives of cholesterol and sodium dodecyl sulfate

    Energy Technology Data Exchange (ETDEWEB)

    Ahmadi, S.; Batchelor, B.; Koseoglu, S.S. [Texas A and M Univ., College Station, TX (United States); Huang, Y.C.

    1995-09-01

    The binding behaviors of five metals (cadmium, copper, nickel, lead, and zinc), individually at pH 6 and collectively at pHs 6 and 3, to deoxycholic acid (DCA) and taurocholic acid (TCA) were compared with those of sodium dodecyl sulfate (SDS) using a continuous diafiltration method. DCA and SDS have been successfully applied in micellar-enhanced ultrafiltration (MEUF) for metal removal from water. In this study, SDS exhibits the strongest binding in the single-component experiments while DCA binds the most in the multicomponent trials. TCA does not show any significant biding compared with DCA and SDS. Overall the molar binding ratios of the mixture at pH 3 were well below those of the other two solutions. This diafiltration technique quantifies the binding characteristics of a surfactant by generating sorption isotherms and determining the intrinsic association constraints with corresponding number of binding sites. These parameters can be useful in designing an efficient MEUF system.

  1. Evaluation of toxicity reduction of sodium dodecyl sulfate submitted to electron beam radiation

    Science.gov (United States)

    Romanelli, M. F.; Moraes, M. C. F.; Villavicencio, A. L. C. H.; Borrely, S. I.

    2004-09-01

    Surfactants, as detergent active substances, are an important source of pollution causing biological adverse effects to aquatic organisms. Several data have been showing ecological disturbance due to the high concentration of surfactants on receiving waters and on wastewater treatment plants. Ionizing radiation has been proved as an effective technology to decompose organic substances and few papers have included ecotoxicological aspects. This paper shows the reduction of acute toxicity of a specific surfactant, sodium dodecyl sulfate (SDS), when diluted in distilled water and submitted to electron beam radiation. The study included two test-organisms, the marine bacteria Vibrio fischeri and the crustacean Daphnia similis. Radiation processing resulted in an important acute toxicity removal for both assays, which can be summarized between 70% and 96%, using 3.0, 6.0, 9.0 and 12.0 kGy as radiation doses. Nevertheless, lower doses demonstrated better effect than 9.0 and 12.0 kGy and the bacterium assay was more sensitive to SDS than crustacean assay.

  2. A comparison study between sodium dodecyl sulfate and sodium dodecyl sulfonate with respect to the thermodynamic properties, micellization, and interaction with poly(ethylene glycol) in aqueous solutions

    International Nuclear Information System (INIS)

    Sadeghi, Rahmat; Shahabi, Somayyeh

    2011-01-01

    Graphical abstract: Apparent molar volume against molality: o, ·, and Δ, respectively in water, (1 and 4) wt% PEG solution at 293.15 K; x, Δ, and lozenge, respectively in water, (1 and 4) wt% PEG solution at 313.15 K. Research highlights: → C 12 H 25 SO 3 Na(SDSn) was seen to interact with PEG more weakly than C 12 H 25 SO 4 Na(SDS). → The constraints on molecular mobility of SDS micelles are larger than those of SDSn. → Entropy change on micellization for SDSn is larger than those for SDS. → Micelle formation of SDS is less endothermic and more spontaneous than that of SDSn. → Micelles of SDS have smaller aggregation number than that of SDSn. - Abstract: The density, sound velocity, and conductivity measurements were performed on aqueous solutions of sodium dodecyl sulfate (C 12 H 25 SO 4 Na) or sodium dodecyl sulfonate (C 12 H 25 SO 3 Na) in the absence and presence of poly(ethylene glycol) (PEG) at different temperatures. Changes in the apparent molar volumes and isentropic compressibilities upon micellization were derived using a pseudophase-transition approach and the infinite dilution apparent molar properties of the monomer and micellar form of C 12 H 25 SO 4 Na and C 12 H 25 SO 3 Na were determined. Variations of the critical micelle concentrations (CMCs) of both surfactants in the solutions investigated with temperature were obtained from which thermodynamic parameters of micellization were estimated. It was found that at low temperature the micelle formation process is endothermic and therefore, this process must be entropically driven. However, upon increasing the temperature, the enthalpic factor becomes more significant and, at temperatures higher than 303.15 K the micellization is enthalpy driven. The interactions between C 12 H 25 SO 4 Na/C 12 H 25 SO 3 Na and PEG were studied and it was found that sodium alkyl sulfonates were seen to interact more weakly than their sulfate analogues.

  3. A comparison study between sodium dodecyl sulfate and sodium dodecyl sulfonate with respect to the thermodynamic properties, micellization, and interaction with poly(ethylene glycol) in aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Sadeghi, Rahmat, E-mail: rsadeghi@uok.ac.ir [Department of Chemistry, University of Kurdistan, Sanandaj (Iran, Islamic Republic of); Shahabi, Somayyeh [Department of Chemistry, University of Kurdistan, Sanandaj (Iran, Islamic Republic of)

    2011-09-15

    Graphical abstract: Apparent molar volume against molality: o, {center_dot}, and {Delta}, respectively in water, (1 and 4) wt% PEG solution at 293.15 K; x, {Delta}, and lozenge, respectively in water, (1 and 4) wt% PEG solution at 313.15 K. Research Highlights: > C{sub 12}H{sub 25}SO{sub 3}Na(SDSn) was seen to interact with PEG more weakly than C{sub 12}H{sub 25}SO{sub 4}Na(SDS). > The constraints on molecular mobility of SDS micelles are larger than those of SDSn. > Entropy change on micellization for SDSn is larger than those for SDS. > Micelle formation of SDS is less endothermic and more spontaneous than that of SDSn. > Micelles of SDS have smaller aggregation number than that of SDSn. - Abstract: The density, sound velocity, and conductivity measurements were performed on aqueous solutions of sodium dodecyl sulfate (C{sub 12}H{sub 25}SO{sub 4}Na) or sodium dodecyl sulfonate (C{sub 12}H{sub 25}SO{sub 3}Na) in the absence and presence of poly(ethylene glycol) (PEG) at different temperatures. Changes in the apparent molar volumes and isentropic compressibilities upon micellization were derived using a pseudophase-transition approach and the infinite dilution apparent molar properties of the monomer and micellar form of C{sub 12}H{sub 25}SO{sub 4}Na and C{sub 12}H{sub 25}SO{sub 3}Na were determined. Variations of the critical micelle concentrations (CMCs) of both surfactants in the solutions investigated with temperature were obtained from which thermodynamic parameters of micellization were estimated. It was found that at low temperature the micelle formation process is endothermic and therefore, this process must be entropically driven. However, upon increasing the temperature, the enthalpic factor becomes more significant and, at temperatures higher than 303.15 K the micellization is enthalpy driven. The interactions between C{sub 12}H{sub 25}SO{sub 4}Na/C{sub 12}H{sub 25}SO{sub 3}Na and PEG were studied and it was found that sodium alkyl sulfonates were seen

  4. Sodium dodecyl sulphate (SDS) induced changes in propensity and kinetics of α-lactalbumin fibrillation.

    Science.gov (United States)

    Kumar, E Kiran; Qumar, Shamsul; Prabhu, N Prakash

    2015-11-01

    Understanding surfactants induced changes on protein folding, aggregation, and fibrillation has a lot of implications in their laboratory and industrial applications. The effect of an anionic surfactant, sodium dodecyl sulphate (SDS), on fibrillation of an acidic protein α-lactalbumin (α-LA) at neutral pH condition was investigated. SDS at lower concentrations increased the lag time by nearly two-fold whereas the fibril elongation rate was not significantly altered. At the concentrations above 0.2mM, SDS lengthened the lag time by many-fold (∼60), but fibril elongation was accelerated by 3-6 fold. At the concentrations above 2mM, SDS inhibited α-LA fibrillation and led it to the formation of amorphous aggregates. These results were compared with the effect of SDS on the fibrillation of lysozyme, a basic protein. Though fibril inhibition was observed on both the proteins at the micellar concentrations of SDS, there were differences in the effect on lag time and elongation rate at the lower concentrations of SDS. This suggests that the inhibition of protein fibrillation by SDS-micelles might be a common mechanism irrespective of the surface charges on protein. Copyright © 2015 Elsevier B.V. All rights reserved.

  5. Enzymatic hydrolysis of sodium dodecyl sulphate (SDS)-pretreated newspaper for cellulosic ethanol production by Saccharomyces cerevisiae and Pichia stipitis.

    Science.gov (United States)

    Xin, Fengxue; Geng, Anli; Chen, Ming Li; Gum, Ming Jun Marcus

    2010-10-01

    Fermentation of enzymatic hydrolysate of waste newspaper was investigated for cellulosic ethanol production in this study. Various nonionic and ionic surfactants were applied for waste newspaper pretreatment to increase the enzymatic digestibility. The surfactant-pretreated newspaper was enzymatically digested in 0.05 M sodium citrate buffer (pH 4.8) with varying solid content, filter paper unit loading (FPU/g newspaper), and ratio of filter paper unit/beta-glucosidase unit (FPU/CBU). Newspaper pretreated with the anionic surfactant sodium dodecyl sulphate (SDS) demonstrated the highest sugar yield. The addition of Tween-80 in the enzymatic hydrolysis process enhanced the enzymatic digestibility of newspaper pretreated with all of the surfactants. Enzymatic hydrolysis of SDS-pretreated newspaper with 15% solid content, 15 FPU/g newspaper, and FPU/CBU of 1:4 resulted in a newspaper hydrolysate conditioning 29.07 g/L glucose and 4.08 g/L xylose after 72 h of incubation at 50 degrees C. The fermentation of the enzymatic hydrolysate with Saccharomyces cerevisiae, Pichia stipitis, and their co-culture produced 14.29, 13.45, and 14.03 g/L of ethanol, respectively. Their corresponding ethanol yields were 0.43, 0.41, and 0.42 g/g.

  6. Vesicle formation and stability in the surfactant sodium 4-(1'-heptylnonyl) benzenesulfonate

    Energy Technology Data Exchange (ETDEWEB)

    Franses, E.I.; Talmon, Y.; Scriven, L.E.; Davis, H.T.; Miller, W.G.

    1982-04-01

    Surfactants composed of a hydrophilic moiety covalently attached to the end of a hydrocarbon chain (e.g., sodium dodecyl sulfate), spontaneously form micelles, equilibrium aggregates, in solution if the surfactant concentration exceeds a critical value called the CMC. Naturally occurring double-tail surfactants (e.g., phospholipids) are not known to form micelles. Over a considerable range in surfactant concentration, 2 phases coexist in equilibrium: a hydrated, multilamellar (smectic) surfactant phase and an aqueous phase saturated with surfactant. In this report the preparation of vesicles, their direct, unstained visualization by electron microscopy, and investigation of their stability and structure by turbidimetry, conductimetry, light microscopy, densitometry, scanning calorimetry, and nuclear magnetic resonance spectroscopy are discussed. Dispersed liquid crystal was studied by the same means. For comparison, parallel studies on bovine lecithin are presented. From the results, it is concluded that these vesicles may be stable for many months, but eventually revert to multilamellar liquid crystals.

  7. Modulation of partition and localization of perfume molecules in sodium dodecyl sulfate micelles.

    Science.gov (United States)

    Fan, Yaxun; Tang, Haiqiu; Strand, Ross; Wang, Yilin

    2016-01-07

    The influence of perfume molecules on the self-assembly of the anionic surfactant sodium dodecyl sulfate (SDS) and their localization in SDS micelles have been investigated by ζ potential, small angle X-ray scattering (SAXS), one- and two-dimensional NMR and isothermal titration microcalorimetry (ITC). A broad range of perfume molecules varying in octanol/water partition coefficients P are employed. The results indicate that the surface charge, size and aggregation number of the SDS micelles strongly depend on the hydrophobicity/hydrophilicity degree of perfume molecules. Three distinct regions along the log P values are identified. Hydrophilic perfumes (log P perfumes (log P > 3.5) are solubilized close to the end of the hydrophobic chains in the SDS micelles and enlarge the micelles with higher ζ potential and a larger aggregation number. The incorporated fraction and micelle properties show increasing tendency for the perfumes in the intermediate log P region (2.0 perfume molecules also affects these properties. The perfumes with a linear chain structure or an aromatic group can penetrate into the palisade layer and closely pack with the SDS molecules. Furthermore, the thermodynamic parameters obtained from ITC show that the binding of the perfumes in the intermediate log P region is more spontaneous than those in the other two log P regions, and the micellization of SDS with the perfumes is driven by entropy.

  8. Structural changes of a sodium dodecyl sulfate (SDS) micelle induced by alcohol molecules.

    Science.gov (United States)

    Méndez-Bermúdez, Jose G; Dominguez, Hector

    2016-01-01

    Coarse-grained dynamical simulations have been performed to investigate the behavior of a surfactant micelle in the presence of six different alcohols: hexanol, octanol, decanol, dodecanol, tetradecanol, and hexadecanol. The self-assembly of sodium dodecyl sulfate (SDS) is modified by the alcohol molecules into cylindrical and bilayer micelles as a function of the alcohol/SDS mass ratio. Therefore, in order to understand, from a molecular point of view, how SDS and alcohol molecules self-organize to form the new micelles, different studies were carried out. Analysis of micelle structures, density profiles, and parameters of order were conducted to characterize the shape and size of those micelles. The density profiles revealed that the alcohol molecules were located at the water-micelle interface next to the SDS molecules at low alcohol/SDS mass ratio. At high alcohol/SDS mass ratios, alcohol molecules moved to the middle of the micelle by increasing their size and by producing a structural change. Moreover, micelle structures and sizes were influenced not only by the alcohol/SDS mass ratio but also by the order of the SDS and alcohol tails. Finally, the size of the micelles and enthalpy calculations were used as order parameters to determine a structural phase diagram of alcohol/SDS mixtures in water. Graphical Abstract Structural transition of SDS/alcohol mixtures.

  9. Beyond the detergent effect: a binding site for sodium dodecyl sulfate (SDS) in mammalian apoferritin.

    Science.gov (United States)

    Liu, Renyu; Bu, Weiming; Xi, Jin; Mortazavi, Shirin R; Cheung-Lau, Jasmina C; Dmochowski, Ivan J; Loll, Patrick J

    2012-05-01

    Although sodium dodecyl sulfate (SDS) is widely used as an anionic detergent, it can also exert specific pharmacological effects that are independent of the surfactant properties of the molecule. However, structural details of how proteins recognize SDS are scarce. Here, it is demonstrated that SDS binds specifically to a naturally occurring four-helix bundle protein: horse apoferritin. The X-ray crystal structure of the apoferritin-SDS complex was determined at a resolution of 1.9 Å and revealed that the SDS binds in an internal cavity that has previously been shown to recognize various general anesthetics. A dissociation constant of 24 ± 9 µM at 293 K was determined by isothermal titration calorimetry. SDS binds in this cavity by bending its alkyl tail into a horseshoe shape; the charged SDS head group lies in the opening of the cavity at the protein surface. This crystal structure provides insights into the protein-SDS interactions that give rise to binding and may prove useful in the design of novel SDS-like ligands for some proteins. © 2012 International Union of Crystallography

  10. Photo Catalytic Removal of Sodium Dodecyl Sulfate From Aquatic Solutions With Prepared ZnO Nanocrystals and UV Irradiation

    Directory of Open Access Journals (Sweden)

    Mohammad Taghi Samadi

    2014-12-01

    Full Text Available In this study, ZnO Nano catalyst has been synthesized and examined as photo catalyst for UV-induced removal of Sodium Dodecyl Sulfate (SDS from aquatic solutions. This anionic surfactant was selected based upon its toxicity, wide use in industrial laundry and as a primary pollutant in municipal waste water systems.This study aimed to investigate removal of surfactant, SDS, in a batch photo catalytic reactor under various operating conditions including ZnO suspension concentration, initial surfactant concentration and initial pH of solution to find out the desired condition for removal of surfactant. ZnO Nano crystals were synthesized using the precipitation method and ZnSO4.7H2O was used as the starting material and NaOH as precipitant. The removal of SDS reactions by UV/ZnO process was performed into a batch photo reactor. In addition, various operating conditions including ZnO suspension concentration, initial surfactant concentration and initial pH of solution were investigated. In total, 98% of surfactant was removed at 40 minute and removal efficiency of SDS increased with increasing pH up to nine and after that with increase in pH, efficiency decreased. Possible roles of inorganic oxidant on the reaction were discussed. The removal of SDS follows pseudo-first order kinetics. Based on the results of this study, ZnO-UV photo catalytic process can be used as an efficient method for further study in detergents removal.

  11. CLONING AND SEQUENCING OF PSEUDOMONAS GENES DETERMINING SODIUM DODECYL-SULFATE BIODEGRADATION

    NARCIS (Netherlands)

    DAVISON, J; BRUNEL, F; PHANOPOULOS, A; PROZZI, D; TERPSTRA, P

    1992-01-01

    The nucleotide sequences of two genes involved in sodium dodecyl sulfate (SDS) degradation, by Pseudomonas, have been determined. One of these, sdsA, codes for an alkyl sulfatase (58 957 Da) and has similarity (31.8% identity over a 201-amino acid stretch) to the N terminus of a predicted protein of

  12. Identification of denatured enzyme proteins in sodium dodecyl sulfate polyacrylamide gels

    NARCIS (Netherlands)

    Hakvoort, T. B.; Veyron, P.; Muilerman, H. G.; van Dijk, W.; Tager, J. M.

    1985-01-01

    A simple modification of the immunological sandwich method of Muilerman et al. for the identification of denatured enzyme proteins in sodium dodecyl sulfate-polyacrylamide gels is described, enabling the method to be used in principle for any enzyme whose activity is not inhibited by binding to

  13. Improved method for silver staining of glycoproteins in thin sodium dodecyl sulfate polyacrylamide gels

    DEFF Research Database (Denmark)

    Møller, H J; Poulsen, J H

    1995-01-01

    A method for detection of glycoproteins in thin sodium dodecyl sulfate polyacrylamide gels was developed by a combination of (i) initial periodic acid oxidation/Alcian blue staining and (ii) subsequent staining with silver nitrate. The procedure allowed detection of as little as 1.6 ng of alpha 1...

  14. Analysis of sperm antigens by sodium dodecyl sulfate gel/protein blot radioimmunobinding method

    Energy Technology Data Exchange (ETDEWEB)

    Lee, C.Y.G. (Univ. of British Columbia, Vancouver, Canada); Huang, Y.S.; Hu, P.C.; Gomel, V.; Menge, A.C.

    1982-06-01

    A radioimmunobinding method based on the blotting of renatured proteins from sodium dodecyl sulfate gels on to nitrocellulose filter papers was developed to analyze the sperm antigens that elicit serum anti-sperm antibodies. In rabbits, serum anti-sperm antibodies were raised by immunization with homologous epididymal spermatozoa mixed with complete Freund's adjuvant. The raised antisera from either male or female rabbits were shown to react with three major sperm protein bands on sodium dodecyl sulfate gels with the corresponding molecular weights of about 70,000 +/- 5000, 14,000, and 13,000, respectively. In humans, the monoclonal antibodies against human sperm were raised by a hybridoma technique. Out of six independent hybrid cell lines that were generated, three of them were shown to secrete immunoglobulins that react with the same two protein bands on sodium dodecyl sulfate gels, which have the approximate molecular weight of 10,000. The same procedure was also used to analyze human serum samples that were shown to contain anti-sperm antibodies by the known techniques. Unique sperm antigens that elicit anti-sperm antibodies in humans were identified and correlated. The results of this study suggest that sodium dodecyl sulfate gel/protein blot radioimmunobinding method may be a sensitive and useful tool for the study of sperm antigens that elicit autoimmune responses and their association with human infertility.

  15. Estimation of interfacial acidity of sodium dodecyl sulfate micelles

    Indian Academy of Sciences (India)

    on various molecules in micro-heterogeneous media such as micelles,3 cyclodextrins4 and polymer-micelle ... of the micro-heterogenous media such as sodium dode- cyl sulfate (SDS) micelles to enhance the ESPT ...... tations. AD thanks Council of Scientific and Indus- trial Research, New Delhi (CSIR) for junior research.

  16. Comparative study on the mechanisms of rotavirus inactivation by sodium dodecyl sulfate and ethylenediaminetetraacetate

    Energy Technology Data Exchange (ETDEWEB)

    Ward, R.L. (Sandia Labs., Albuquerque, NM); Ashley, C.S.

    1980-06-01

    This report describes a comparative study on the effects of the anionic detergent sodium dodecyl sulfate and the chelating agent ethylenediaminetetraacetate on purified rotavirus SA-11 particles. Both chemicals readily inactivated rotavirus at quite low concentrations and under very mild conditions. In addition, both agents modified the viral capsid and prevented the adsorption of inactivated virions to cells. Capsid damage by ethylenediaminetetraacetate caused a shift in the densities of rotavirions from about l.35 to about 1.37 g/ml and a reduction in their sedimentation coefficients. Sodium dodcyl sulfate, on the other hand, did not detectably alter either of these physical properties of rotavirions. Both agents caused some alteration of the isoelectric points of the virions. Finally, analysis of rotavirus proteins showed that ethylenediaminetetraacetate caused the loss of two protein peaks from the electrophoretic pattern of virions but sodium dodecyl sulfate caused the loss of only one of these same protein peaks.

  17. Effect of Sodium Dodecyl Sulfate (SDS) and Tween 80 on Cell Viability in an Air-Cathode Microbial Fuel Cell

    KAUST Repository

    Fregoso, Luisa

    2011-07-01

    Microbial fuel cells (MFCs) generate current via electrochemical reactions produced by bacteria attached to the anode that oxidize organic matter. Due to their high volume use in household products, some concentration of surfactant will reach wastewater treatment plants. The average surfactant concentration in wastewater ranges from 10 to 20 mg L-1, and up to 300 mg L-1, for domestic and industrial wastewaters, respectively. This study aimed to demonstrate the feasibility of enhancing power production by adding Tween 80 and SDS surfactants to air-cathode MFCs, and their effect in cell viability at the anodic biofilm. In order to analyze the effect of anionic and nonionic surfactants in MFCs performance, eight MFCs were spiked with two types of surfactants, the anionic surfactant sodium dodecyl sulfate (SDS) and the nonionic surfactant Tween® 80 at two different concentrations 10 and 100 mg L-1. Cell viability at the anodic biofilms was examined using the LIVE/DEAD BacLight viability assay and images were visualized with a confocal laser scanning microscope. The electrochemical results demonstrate that, for an air-cathode MFC operating on 1 g L-1 acetate in a fed-batch mode, reactors where SDS was added show a lower overall performance, maximum PD of 544 mW m-2, CE of 12.3%, Rint of 322 Ω (10 mg L-1) and maximum PD of 265 mW m-2, CE of 9.4%, Rint of 758 Ω (100 mg L-1). Reactors where Tween 80 was added show quite stable performance, maximum PD of 623 mW m-2, CE of 15.4%, Rint of 216 Ω (10 mg L-1) and maximum PD of 591 mW m-2, CE of 10.8%, Rint of 279 Ω (100 mg L-1), compared with reactors operating at only acetate as a substrate, maximum PD of 574 mW m-2. Confocal microscopy images confirm this observation and biofilm viability appeared severely compromised in SDS reactors, especially at high concentrations. This study has opened up a whole new research area in determining which types of surfactants are toxic to the anodic biofilm and to further investigate the

  18. Adsorption mechanism of sodium dodecyl benzene sulfonate on carbon blacks by adsorption isotherm and zeta potential determinations.

    Science.gov (United States)

    Zhao, Yapei; Lu, Pei; Li, Caiting; Fan, Xiaopeng; Wen, Qingbo; Zhan, Qi; Shu, Xin; Xu, Tieliang; Zeng, Guangming

    2013-01-01

    Surfactant solutions were propounded to remove fine and hydrophobic carbon black particles from coal-fired flue gas. The adsorption mechanisms between sodium dodecyl benzene sulfonate (SDBS, an anionic surfactant) and carbon black particles in suspension were investigated. The influence of inorganic salt (NaCl) was also considered. As results showed, hydrophobic interactions contributed to the strong adsorption between SDBS and carbon black particles in the absence of NaCl, and adding NaCl affected the adsorption process. The adsorption amount of SDBS significantly increased when NaCl was added into the SDBS solution; however, when SDBS was in low concentration, the amount of adsorbed SDBS, which was responsible for the shift of zeta potentials, varied little under different concentrations of NaCl. This indicated that the adsorption of SDBS was mainly caused by hydrophobic interaction and Na+ could not change the adsorption of SDBS on adsorption site when SDBS was in low concentration. Moreover, the adsorbed SDBS and Na+ were retained in the Stern layer.

  19. The Effect of Sodium Dodecyl Sulfate (SDS) and Cetyltrimethylammonium Bromide (CTAB) on the Properties of ZnO Synthesized by Hydrothermal Method

    Science.gov (United States)

    Ramimoghadam, Donya; Hussein, Mohd Zobir Bin; Taufiq-Yap, Yun Hin

    2012-01-01

    ZnO nanostructures were synthesized by hydrothermal method using different molar ratios of cetyltrimethylammonium bromide (CTAB) and Sodium dodecyl sulfate (SDS) as structure directing agents. The effect of surfactants on the morphology of the ZnO crystals was investigated by field emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM) techniques. The results indicate that the mixture of cationic-anionic surfactants can significantly modify the shape and size of ZnO particles. Various structures such as flakes, sheets, rods, spheres, flowers and triangular-like particles sized from micro to nano were obtained. In order to examine the possible changes in other properties of ZnO, characterizations like powder X-ray diffraction (PXRD), thermogravimetric and differential thermogravimetric analysis (TGA-DTG), FTIR, surface area and porosity and UV-visible spectroscopy analysis were also studied and discussed. PMID:23202952

  20. Fast Removal of Citalopram Drug from Waste Water Using Magnetic Nanoparticles Modified with Sodium Dodecyl Sulfate Followed by UV-Spectrometry

    Directory of Open Access Journals (Sweden)

    M. Khoeini Sharifabadi

    2014-02-01

    Full Text Available A simple and sensitive, solid-phase extraction method for the removal of Citalopram drug from waste water has been developed by using magnetic nanoparticles modified with surfactant sodium dodecyl sulfate. These magnetic nanoparticles have shown great adsorptive tendency towards Citalopram drug. The effect of different parameters influencing the extraction efficiency of this drug were investigated and optimized including the pH, amount of the surfactant, contact time and temperature. The extracts were analyzed by ultraviolet spectrophotometry at 239nm. Under these conditions, the related standard deviation (RSD % of the method at two concentrations (5 and 50µg.mL-1 was in the range of (3.14–3.75 % (n = 8. The calibration curve was linear in the range of 2-100 µg.mL-1 of Citalopram drug with a correlation coefficient of >0.99.

  1. Fast Removal of Citalopram Drug from Waste Water Using Magnetic Nanoparticles Modified with Sodium Dodecyl Sulfate Followed by UV-Spectrometry

    Directory of Open Access Journals (Sweden)

    M. Khoeini Sharifabadi

    2013-04-01

    Full Text Available A simple and sensitive, solid-phase extraction method for the removal of Citalopram drug from waste water has been developed by using magnetic nanoparticles modified with surfactant sodium dodecyl sulfate. These magnetic nanoparticles have shown great adsorptive tendency towards Citalopram drug. The effect of different parameters influencing the extraction efficiency of this drug were investigated and optimized including the pH, amount of the surfactant, contact time and temperature. The extracts were analyzed by ultraviolet spectrophotometry at 239nm. Under these conditions, the related standard deviation (RSD % of the method at two concentrations (5 and 50µg.mL-1 was in the range of (3.14–3.75 % (n = 8. The calibration curve was linear in the range of 2-100 µg.mL-1 of Citalopram drug with a correlation coefficient of >0.99.

  2. Influence of Surfactants on Sodium Chloride Crystallization in Confinement.

    Science.gov (United States)

    Qazi, Mohsin J; Liefferink, Rinse W; Schlegel, Simon J; Backus, Ellen H G; Bonn, Daniel; Shahidzadeh, Noushine

    2017-05-02

    We study the influence of different surfactants on NaCl crystallization during evaporation of aqueous salt solutions. We found that at concentrations of sodium chloride close to saturation, only the cationic surfactant CTAB and the nonionic surfactant Tween 80 remain stable. For the nonionic surfactant, the high concentration of salt does not significantly change either the critical micellar concentration (CMC) or the surface tension at the CMC; for the cationic surfactant, the CMC is reduced by roughly 2 orders of magnitude upon adding the salt. The presence of both types of surfactants in the salt solution delays the crystallization of sodium chloride with evaporation. This, in turn, leads to high supersaturation which induces the rapid precipitation of a hopper crystal in the bulk. The crystallization inhibitor role of these surfactants is shown to be mainly due to the passivation of nucleation sites at both liquid/air and solid/liquid interfaces rather than a change in the evaporation rate which is found not to be affected by the presence of the surfactants. The adsorption of surfactants at the liquid/air interface prevents the crystallization at this location which is generally the place where the precipitation of sodium chloride is observed. Moreover, sum frequency generation spectroscopy measurements show that the surfactants are also present at the solid/liquid interface. The incorporation of the surfactants into the salt crystals is investigated using a novel, but simple, method based on surface tension measurements. Our results show that the nonionic surfactant Tween 80 is incorporated in the NaCl crystals but the cationic surfactant CTAB is not. Taken together, these results therefore allow us to establish the effect of the presence of surfactants on sodium chloride crystallization.

  3. Preparation of Barley Storage Protein, Hordein, for Analytical Sodium Dodecyl Sulfate-Polyacrylamide Gel Electrophoresis

    DEFF Research Database (Denmark)

    Doll, Hans; Andersen, Bente

    1981-01-01

    The extraction, reduction, and alkylation of barley hordein for routine electrophoresis in sodium dodecyl sulfate-polyacrylamide gels were studied to set up a simple preparation procedure giving well-resolved bands in the electrophoresis gel. Hordein was extracted from single crushed seeds or flour...... by aqueous 50% propan-2-ol containing a Tris-borate buffer, pH 8.6. The presence of the buffer facilitates the consecutive complete reduction of the extracted protein in the alcohol. Reduction and alkylation in the buffer containing propan-2-ol give sharper bands in the electrophoresis than reduction...

  4. Activity staining of pectinesterase on polyacrylamide gels after acidic or sodium dodecyl sulfate electrophoresis.

    Science.gov (United States)

    Hou, W C; Lin, Y H

    1998-05-01

    Pectinesterase (PE), from commercial orange peels or ammonium sulfate fractionation (50-80% saturation) of pea pods, was detected on polyacrylamide gels after native acidic polyacrylamide gel electrophoresis (PAGE) or sodium dodecyl sulfate (SDS)-PAGE by using the synthetic substrate beta-naphthyl acetate (beta-NA). The release of beta-naphthol (at 322 nm) from beta-NA was proportional to PE activity. The PE activity bands on polyacrylamide gels after native acidic PAGE or SDS-PAGE were stained with a combination of tetrazotized o-dianisidine and beta-NA. This fast and sensitive method can be used for enzyme purification and characterization.

  5. Simple and sensitive method for spectrofluorimetric determination of dodecyl benzene sulfonic acid sodium

    Science.gov (United States)

    Liu, Jinshui; Liu, Yan; Li, Peng; Wang, Lun

    2006-12-01

    The interaction of poly(diallyldimethyl ammonium chloride) (PDDA) with dodecyl benzene sulfonic acid sodium (DBS) has been studied by fluorescence spectra. The fluorescence of DBS can be greatly enhanced by addition of PDDA, owing to the interaction between PDDA and DBS. The enhancement intensity of fluorescence was proportional to the concentration of DBS over the range 2.5 × 10 -7 to 9.6 × 10 -5 mol L -1. Its detection limit is 3.5 × 10 -7 mol L -1. The method has high sensitivity and selectivity and was applied to the determination of trace amounts of DBS in water samples with satisfactory result.

  6. Structural Studies on Nonequilibrium Microstructures of Dioctyl Sodium Dodecyl Sulfosuccinate (Aerosol-OT in p-Toluenesulfonic Acid and Phosphatidylcholine

    Directory of Open Access Journals (Sweden)

    M. K. Temgire

    2012-01-01

    Full Text Available Several microstructures are evolved at the interface when sparingly soluble solid surfactants come in contact with water. One class of these microstructures is termed as “myelin figures”; these were observed when phosphatidylcholine came in contact with water. Although the myelins are initially simple rod-like, complex forms like helices, coils and so forth. appear in the later stage. Finally, the myelins fuse together to form a complex mosaic-like structure. When studied by taking a cross-section using cryoscanning electron microscopy, it revealed concentric circular pattern inside the myelin figures. The cross-sections of (dioctyl sodium dodecyl sulfosiccinate AOT/water system myelin internal structures were lost. When p-toluenesulfonic acid (PTS 2 wt% was present in the water phase, AOT myelins revealed the internal microstructures. It has annular concentric ring-like structure with a core axon at the centre. Further investigation revealed new microstructures for the first time having multiple axons in the single-myelin strand.

  7. Partial characterization of biosurfactant from Lactobacillus pentosus and comparison with sodium dodecyl sulphate for the bioremediation of hydrocarbon contaminated soil.

    Science.gov (United States)

    Moldes, A B; Paradelo, R; Vecino, X; Cruz, J M; Gudiña, E; Rodrigues, L; Teixeira, J A; Domínguez, J M; Barral, M T

    2013-01-01

    The capability of a cell bound biosurfactant produced by Lactobacillus pentosus, to accelerate the bioremediation of a hydrocarbon-contaminated soil, was compared with a synthetic anionic surfactant (sodium dodecyl sulphate SDS-). The biosurfactant produced by the bacteria was analyzed by Fourier transform infrared spectroscopy (FTIR) that clearly indicates the presence of OH and NH groups, C=O stretching of carbonyl groups and NH nebding (peptide linkage), as well as CH2-CH3 and C-O stretching, with similar FTIR spectra than other biosurfactants obtained from lactic acid bacteria. After the characterization of biosurfactant by FTIR, soil contaminated with 7,000 mg Kg(-1) of octane was treated with biosurfactant from L. pentosus or SDS. Treatment of soil for 15 days with the biosurfactant produced by L. pentosus led to a 65.1% reduction in the hydrocarbon concentration, whereas SDS reduced the octane concentration to 37.2% compared with a 2.2% reduction in the soil contaminated with octane in absence of biosurfactant used as control. Besides, after 30 days of incubation soil with SDS or biosurfactant gave percentages of bioremediation around 90% in both cases. Thus, it can be concluded that biosurfactant produced by L. pentosus accelerates the bioremediation of octane-contaminated soil by improving the solubilisation of octane in the water phase of soil, achieving even better results than those reached with SDS after 15-day treatment.

  8. Partial Characterization of Biosurfactant from Lactobacillus pentosus and Comparison with Sodium Dodecyl Sulphate for the Bioremediation of Hydrocarbon Contaminated Soil

    Directory of Open Access Journals (Sweden)

    A. B. Moldes

    2013-01-01

    Full Text Available The capability of a cell bound biosurfactant produced by Lactobacillus pentosus, to accelerate the bioremediation of a hydrocarbon-contaminated soil, was compared with a synthetic anionic surfactant (sodium dodecyl sulphate SDS-. The biosurfactant produced by the bacteria was analyzed by Fourier transform infrared spectroscopy (FTIR that clearly indicates the presence of OH and NH groups, C=O stretching of carbonyl groups and NH nebding (peptide linkage, as well as CH2–CH3 and C–O stretching, with similar FTIR spectra than other biosurfactants obtained from lactic acid bacteria. After the characterization of biosurfactant by FTIR, soil contaminated with 7,000 mg Kg−1 of octane was treated with biosurfactant from L. pentosus or SDS. Treatment of soil for 15 days with the biosurfactant produced by L. pentosus led to a 65.1% reduction in the hydrocarbon concentration, whereas SDS reduced the octane concentration to 37.2% compared with a 2.2% reduction in the soil contaminated with octane in absence of biosurfactant used as control. Besides, after 30 days of incubation soil with SDS or biosurfactant gave percentages of bioremediation around 90% in both cases. Thus, it can be concluded that biosurfactant produced by L. pentosus accelerates the bioremediation of octane-contaminated soil by improving the solubilisation of octane in the water phase of soil, achieving even better results than those reached with SDS after 15-day treatment.

  9. Temporal and geographical distributions of epilithic sodium dodecyl sulfate-degrading bacteria in a polluted South Wales river

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, D.J.; Day, M.J.; Russell, N.J.; White, G.F.

    1988-02-01

    Epilithic bacteria were isolated nonselectively from riverbed stones and examined by gel zymography for their ability to produce alkylsulfatase (AS) enzymes and thus to metabolize alkyl sulfate surfactants such as sodium dodecyl sulfate. The percentages of AS+ isolates from stone epilithon at five sites from the source to the river mouth were measured on five sampling days spread over 1 year. The results showed that (i) the prevalence of epilithic AS+ strains (as a percentage of all isolates) was much higher at polluted sites than at the source; (ii) when averaged over the whole river, percentages of AS+ strains were significantly higher at the end of summer compared with either the preceding or the following winter; (iii) analysis of site-sampling time interactions indicated that water quality factors (e.g., biochemical oxygen demand and dissolved oxygen concentration) rather than climatic factors determined the distributions of epilithic AS+ isolates; (iv) constitutive strains were the most prevalent (7.2% of all isolates), with smaller numbers of isolates with inducible (4.5%) and repressible (1.7%) enzymes.

  10. Binding of sodium dodecyl sulfate with linear and branched polyethyleneimines in aqueous solution at different pH values.

    Science.gov (United States)

    Wang, Hao; Wang, Yilin; Yan, Haike; Zhang, Jin; Thomas, Robert K

    2006-02-14

    Isothermal titration microcalorimetry (ITC), conductivity, and turbidity measurements have been carried out to study the interaction of sodium dodecyl sulfate (SDS) with polyethyleneimines (PEI) including linear PEI and branched PEI at different pH values of 3, 7, and 10. In all cases, the polymers show a remarkable affinity toward SDS. At pH 3, the polymer PEI is a strong polycation, and the binding is dominated by electrostatic 1:1 charge neutralization with the anionic surfactant. At pH 7, the electrostatic attraction between SDS and PEI is weak, and the hydrophobic interaction becomes stronger. At the natural pH of 10, PEI is essentially nonionic and binds SDS in the form of polymer-bound surfactant aggregates. The charge neutralization concentration (C1) of SDS for the PEI-SDS complex can be derived from the curves of variation of the enthalpy, conductivity, and turbidity with SDS concentration. There is good agreement between the results from the three methods and all show a decrease with increasing pH. The total interaction enthalpies (deltaH(total)) of PEI with SDS are obtained from the observed enthalpy curves and the difference enthalpy (deltaH*) between the total enthalpy of branched PEI with SDS, and the total enthalpy of linear PEI with SDS can be derived from the obtained deltaH(total). The difference deltaH* increases dramatically as pH increases, which indicates that the interactions are different for linear PEI and branched PEI at high pH values. A schematic map of the different states of aggregation is presented.

  11. Hexafluoroisopropanol-modified cetyltrimethylammonium bromide/sodium dodecyl sulfate vesicles as a pseudostationary phase in electrokinetic chromatography.

    Science.gov (United States)

    Tian, Yu; Li, Yunfang; Mei, Jie; Deng, Bin; Xiao, Yuxiu

    2015-07-24

    A novel catanionic surfactant vesicle system, formulated from hexafluoroisopropanol (HFIP), cetyltrimethylammonium bromide (CTAB) and sodium dodecyl sulfate (SDS), was developed as pseudostationary phase (PSP) in electrokinetic chromatography (EKC). HFIP, as an organic modifier with the prominent properties of ionization, hydrogen bond donor and hydrophobicity, was used to effectively promote the spontaneous vesicle formation from CTAB/SDS mixed aqueous solutions, where precipitates are easy to occur due to long carbon chains, and adjust the performance of CTAB/SDS vesicles. The physical features (size and viscosity) and electrophoretic parameters (electroosmotic mobility, electrophoretic mobility and elution range) of HFIP-modified CTAB/SDS vesicles were characterized as HFIP volume content (0-4%, v/v), CTAB/SDS molar ratio (2:8-7:3mol/mol) and total surfactant concentration (10-50mM) varying, respectively. The 3% v/v HFIP-modified CTAB/SDS (3:7mol/mol, 50mM) vesicle system proves to have the largest mean diameter (288.20nm) and the widest elution range (12.41), which is also much wider than that of the corresponding other four PSP systems including trifluoroethanol (TFE)-modified CTAB/SDS vesicles (5.69), isopropanol-modified CTAB/SDS micelles (2.03), HFIP-modified SDS micelles (4.86) and unmodified SDS micelles (3.12). The chromatographic performance of the HFIP-modified vesicle system was evaluated by separating eight polycyclic aromatic hydrocarbons, nitrotoluene positional isomers, five positively charged and five negatively charged/neutral drugs, respectively. Baseline or near-baseline separation was achieved for each series of solutes. Compared with the TFE-modified vesicle system, as well as the HFIP-modified and unmodified SDS micelle systems, the HFIP-modified vesicle system shows the best separation selectivity, the highest or comparable efficiency, and the lowest retention. Copyright © 2015 Elsevier B.V. All rights reserved.

  12. Influence of sodium dodecyl sulfate concentration on the photocatalytic activity and dielectric properties of intercalated sodium dodecyl sulfate into Zn–Cd–Al layered double hydroxide

    Energy Technology Data Exchange (ETDEWEB)

    Ahmed, Abdullah Ahmed Ali, E-mail: abdullah2803@gmail.com [Department of Physics, Faculty of Applied Science, Thamar University, Dhamar 87246 (Yemen); Talib, Zainal Abidin [Department of Physics, Faculty of Science, Universiti Putra Malaysia, UPM, Serdang, Selangor 43400 (Malaysia); Hussein, Mohd Zobir [Advanced Materials and Nanotechnology Laboratory, Institute of Advanced Technology (ITMA), Universiti Putra Malaysia, UPM, Serdang, Selangor 43400 (Malaysia)

    2015-02-15

    Highlights: • Zn–Cd–Al–LDH–DS were synthesized with different SDS concentrations. • Photocatalytic activity of samples was improved by increasing SDS concentration. • Dielectric response of LDH can be described by anomalous low frequency dispersion. • The dc conductivity values were calculated for Zn–Cd–Al–LDH–DS samples. • ESR spectra exhibited the successful intercalation of DS molecule into LDH gallery. - Abstract: Sodium dodecyl sulfate (SDS) has been successfully intercalated into Zn–Cd–Al–LDH precursor with different SDS concentrations (0.2, 0.3, 0.4, 0.5 and 1 mol L{sup −1}) using the coprecipitation method at (Zn{sup 2+} + Cd{sup 2+})/Al{sup 3+} molar ratio of 13 and pH 8. The structural, morphological, texture and composition properties of the synthesized (Zn–Cd–Al–LDH–DS) nanostructure were investigated using powder X-ray diffraction (PXRD), scanning electron microscope (SEM), thermogravimetric analysis (TGA) and Fourier transform infrared (FT-IR), respectively. The photocatalytic activity of these materials was developed by increasing the concentration of intercalated SDS. The absorbance spectra have been used to detect an anion in the LDH interlayer before and after the intercalation process, which confirmed the presence of the dodecyl sulfate (DS{sup −}) anion into LDH gallery after intercalation. The anomalous low frequency dispersion (ALFD) has been used to describe the dielectric response of Zn–Cd–Al–LDH–DS nanostructure using the second type of universal power law. At low frequency, the polarization effect of electrodes caused the rising in dielectric constant and loss values. An important result of the dielectric measurements is the calculated dc conductivity values, which are new in dielectric spectroscopy of LDH materials. An important result of the electron spin resonance (ESR) spectra exhibited the successful intercalation of DS molecule into LDH gallery. The g-factor value was affected by

  13. Synthesis and properties of di-n-dodecyl alpha,omega-alkyl bisphosphate surfactants

    NARCIS (Netherlands)

    Duivenvoorde, F.L.; Feiters, M.C.; Van der Gaast, S.J.; Engberts, J.B.F.N.

    1997-01-01

    Three gemini and two bolaform bisphosphate surfactants of the type 12-s-12, with s = 6, 8, 12, 18, and 24 carbon atoms, have been synthesized and their aggregation behavior has been studied. The bolaform surfactants 12-18-12 and 12-24-12 were found to form vesicles in aqueous solution, as indicated

  14. Sodium Dodecyl Sulfate (SDS)-Loaded Nanoporous Polymer as Anti-Biofilm Surface Coating Material

    Science.gov (United States)

    Li, Li; Molin, Soeren; Yang, Liang; Ndoni, Sokol

    2013-01-01

    Biofilms cause extensive damage to industrial settings. Thus, it is important to improve the existing techniques and develop new strategies to prevent bacterial biofilm formation. In the present study, we have prepared nanoporous polymer films from a self-assembled 1,2-polybutadiene-b-polydimethylsiloxane (1,2-PB-b-PDMS) block copolymer via chemical cross-linking of the 1,2-PB block followed by quantitative removal of the PDMS block. Sodium dodecyl sulfate (SDS) was loaded into the nanoporous 1,2-PB from aqueous solution. The SDS-loaded nanoporous polymer films were shown to block bacterial attachment in short-term (3 h) and significantly reduce biofilm formation in long-term (1 week) by gram-negative bacterium Escherichia coli. Tuning the thickness or surface morphology of the nanoporous polymer films allowed to extent the anti-biofilm capability. PMID:23377015

  15. THE ACTION OF SODIUM DODECYL SULFATE ON THE CHLOROPHYLL-PROTEIN COMPOUND OF THE SPINACH LEAF.

    Science.gov (United States)

    Smith, E L

    1941-05-20

    1. Sodium dodecyl sulfate (SDS) attacks the chlorophyll-protein compound modifying its protein properties and absorption spectrum. 2. In the presence of SDS, chlorophyll is quantitatively converted to phaeophytin; i.e., magnesium is removed from the molecule. This reaction, measured spectrophotometrically, proceeds at a rate directly proportional to the hydrogen ion concentration. At constant pH, the rate is proportional to the SDS concentration until a maximum rate is achieved. 3. The chlorophyll or phaeophytin (depending on the pH) remains attached to the protein, since the prosthetic group cannot be separated by ultrafiltration, dialysis, or fractional precipitation. 4. This suggests that the magnesium plays no part in binding chlorophyll to the split protein fragments, but may be concerned in binding the larger units, since the metal becomes extremely labile when the protein is split.

  16. Heme degradation upon production of endogenous hydrogen peroxide via interaction of hemoglobin with sodium dodecyl sulfate.

    Science.gov (United States)

    Salehi, N; Moosavi-Movahedi, A A; Fotouhi, L; Yousefinejad, S; Shourian, M; Hosseinzadeh, R; Sheibani, N; Habibi-Rezaei, M

    2014-04-05

    In this study the hemoglobin heme degradation upon interaction with sodium dodecyl sulfate (SDS) was investigated using UV-vis and fluorescence spectroscopy, multivariate curve resolution analysis, and chemiluminescence method. Our results showed that heme degradation occurred during interaction of hemoglobin with SDS producing three fluorescent components. We showed that the hydrogen peroxide, produced during this interaction, caused heme degradation. In addition, the endogenous hydrogen peroxide was more effective in hemoglobin heme degradation compared to exogenously added hydrogen peroxide. The endogenous form of hydrogen peroxide altered oxyHb to aquamethemoglobin and hemichrome at low concentration. In contrast, the exogenous hydrogen peroxide lacked this ability under same conditions. Copyright © 2014 Elsevier B.V. All rights reserved.

  17. A thermodynamic investigation on the binding of lysozme with sodium dodecyl sulfate

    International Nuclear Information System (INIS)

    Behbeheni, G.R.; Ramazani, S.; Gonbadi, K.

    2013-01-01

    The interaction of Sodium Dodecyl Sulfate (SDS) with hen egg lysozyme have been investigated at 298, 303 and 308 K in phosphate buffer at two different pH values (5 and 7), by isothermal titration calorimetry. The calorimetric data analysis allows the measurement of the complete set of thermodynamic parameters. The negative SDS ion binds to positive residues, neutralizes the protein surface charges and leads to precipitation and turbidity of the solution. At low concentrations of SDS, the binding is mainly electrostatic, with some simultaneous interaction of the hydrophobic tail with nearby hydrophobic patches on the lysozyme. The enthalpies of denaturation at pH 7 are 180.47, 198.51 and 216.56 for 298, 303 and 308 K respectively. (author)

  18. Sodium Dodecyl Sulfate (SDS-Loaded Nanoporous Polymer as Anti-Biofilm Surface Coating Material

    Directory of Open Access Journals (Sweden)

    Sokol Ndoni

    2013-02-01

    Full Text Available Biofilms cause extensive damage to industrial settings. Thus, it is important to improve the existing techniques and develop new strategies to prevent bacterial biofilm formation. In the present study, we have prepared nanoporous polymer films from a self-assembled 1,2-polybutadiene-b-polydimethylsiloxane (1,2-PB-b-PDMS block copolymer via chemical cross-linking of the 1,2-PB block followed by quantitative removal of the PDMS block. Sodium dodecyl sulfate (SDS was loaded into the nanoporous 1,2-PB from aqueous solution. The SDS-loaded nanoporous polymer films were shown to block bacterial attachment in short-term (3 h and significantly reduce biofilm formation in long-term (1 week by gram-negative bacterium Escherichia coli. Tuning the thickness or surface morphology of the nanoporous polymer films allowed to extent the anti-biofilm capability.

  19. Differentiation and distribution of colistin- and sodium dodecyl sulfate-tolerant cells in Pseudomonas aeruginosa biofilms

    DEFF Research Database (Denmark)

    Haagensen, Janus Anders Juul; Klausen, M; Ernst, RK

    2007-01-01

    -targeting antibacterial agents. All biofilm-associated cells were sensitive to the antibacterial agents when tested in standard plate assays. A mutation eliminating the production of type IV pili, and hence surface-associated motility, prevented the formation of regular mushroom-shaped structures in the flow cell......-shaped multicellular structures. The cap-forming subpopulation was found to develop tolerance to membrane-targeting antimicrobial agents, such as the cyclic cationic peptide colistin and the detergent sodium dodecyl sulfate. The stalk-forming subpopulation, on the other hand, was sensitive to the membrane...... that only the cap-forming subpopulation in biofilms treated with colistin expresses the pmr operon. These results suggest that increased antibiotic tolerance in biofilms may be a consequence of differentiation into distinct subpopulations with different phenotypic properties....

  20. Sodium Dodecyl Sulfate- Polyacrylamide Gel Electrophoresis (SDS- PAGE) of Irradiated Wheat Flour Proteins

    International Nuclear Information System (INIS)

    Souzan, R.M.

    1999-01-01

    Sodium dodecyl sulfate - polyacrylamide gel electrophoresis (SDS-PAGE) of wheat (Triticum aestivum L) flour have revealed 23 polypeptides of molecular weights between 170 and 11.57 KDa, High molecular weight glutenin subunits (LMW-GS) were distinguished. Densitometric analysis of the gel showed the effect of radiation on polypeptide constitution at radiation energy up to 7.5 kGy. Irradiation of wheat flour with 2.5 kGy have resulted in a slight increase in the molecular weight of wheat flour protein subunits. The increase of irradiation dose to 5.0 kGy has also induced an additional increase of molecular weight of protein subunits. The continuity in application of more radiation energy to a level of 7.5 kGy have resulted in the prevalence of degradation processes of all protein subunits more than the aggregation

  1. Sodium dodecyl sulfate-capillary gel electrophoresis of polyethylene glycolylated interferon alpha.

    Science.gov (United States)

    Na, Dong H; Park, Eun J; Youn, Yu S; Moon, Byung W; Jo, Yeong W; Lee, Sung H; Kim, Won-Bae; Sohn, Yeowon; Lee, Kang C

    2004-02-01

    Sodium dodecyl sulfate-capillary gel electrophoresis (SDS-CGE) using a hydrophilic replaceable polymer network matrix was applied to characterize the polyethylene glycol(PEG)ylated interferon alpha (PEG-IFN). The SDS-CGE method resulted in a clearer resolution in both the PEG-IFN species and the native IFN species. The distribution profile of PEGylation determined by SDS-CGE was consistent with that obtained by SDS-polyacrylamide gel electrophoresis (PAGE) with Coomassie blue or barium iodide staining. The result was also compared using matrix-assisted laser desorption/ionization-time of flight-mass spectrometry. SDS-CGE was also useful for monitoring the PEGylation reaction to optimize the reaction conditions, such as reaction molar ratio. This study shows the potential of SDS-CGE as a new method for characterizing the PEGylated proteins with advantages of speed, minimal sample consumption and high resolution.

  2. Modification of an acetone-sodium dodecyl sulfate disruption method for cellular protein extraction from neuropathogenic Clostridium botulinum

    Science.gov (United States)

    An acetone-sodium dodecyl sulfate (SDS) disruption method was used for the extraction of cellular proteins from neurotoxigenic Clostridium botulinum. The amount of protein extracted per gram of dry weight and the protein profile as revealed by polyacrylamide gel electrophoresis (PAGE) was comparabl...

  3. Effect of sodium dodecyl sulfate (SDS) on stress response in the Mediterranean mussel (Mytilus Galloprovincialis): regulatory volume decrease (Rvd) and modulation of biochemical markers related to oxidative stress.

    Science.gov (United States)

    Messina, Concetta Maria; Faggio, Caterina; Laudicella, Vincenzo Alessandro; Sanfilippo, Marilena; Trischitta, Francesca; Santulli, Andrea

    2014-12-01

    In this study the effects of an anionic surfactant, sodium dodecyl sulfate (SDS), are assessed on the Mediterranean mussel (Mytilus galloprovincialis), exposed for 18 days at a concentration ranging from 0.1 mg/l to 1 mg/l. The effects are monitored using biomarkers related to stress response, such as regulatory volume decrease (RVD), and to oxidative stress, such as reactive oxygen species (ROS), endogenous antioxidant systems and Hsp70 levels. The results demonstrate that cells from the digestive gland of M. galloprovincialis, exposed to SDS were not able to perform the RVD owing to osmotic stress. Further, SDS causes oxidative stress in treated organisms, as demonstrated by the increased ROS production, in comparison to the controls (pSDS, under the tested concentrations, exerts a toxic effect in mussels in which the disruption of the osmotic balance follows the induction of oxidative stress. Copyright © 2014 Elsevier B.V. All rights reserved.

  4. Activation of Recombinantly Expressed l-Amino Acid Oxidase from Rhizoctonia solani by Sodium Dodecyl Sulfate

    Directory of Open Access Journals (Sweden)

    Katharina Hahn

    2017-12-01

    Full Text Available l-Amino acid oxidases (l-AAO catalyze the oxidative deamination of l-amino acids to the corresponding α-keto acids. The non-covalently bound cofactor FAD is reoxidized by oxygen under formation of hydrogen peroxide. We expressed an active l-AAO from the fungus Rhizoctonia solani as a fusion protein in E. coli. Treatment with small amounts of the detergent sodium dodecyl sulfate (SDS stimulated the activity of the enzyme strongly. Here, we investigated whether other detergents and amphiphilic molecules activate 9His-rsLAAO1. We found that 9His-rsLAAO1 was also activated by sodium tetradecyl sulfate. Other detergents and fatty acids were not effective. Moreover, effects of SDS on the oligomerization state and the protein structure were analyzed. Native and SDS-activated 9His-rsLAAO1 behaved as dimers by size-exclusion chromatography. SDS treatment induced an increase in hydrodynamic radius as observed by size-exclusion chromatography and dynamic light scattering. The activated enzyme showed accelerated thermal inactivation and an exposure of additional protease sites. Changes in tryptophan fluorescence point to a more hydrophilic environment. Moreover, FAD fluorescence increased and a lower concentration of sulfites was sufficient to form adducts with FAD. Taken together, these data point towards a more open conformation of SDS-activated l-amino acid oxidase facilitating access to the active site.

  5. Molecular Insight into Human Lysozyme and Its Ability to Form Amyloid Fibrils in High Concentrations of Sodium Dodecyl Sulfate: A View from Molecular Dynamics Simulations.

    Directory of Open Access Journals (Sweden)

    Majid Jafari

    Full Text Available Changes in the tertiary structure of proteins and the resultant fibrillary aggregation could result in fatal heredity diseases, such as lysozyme systemic amyloidosis. Human lysozyme is a globular protein with antimicrobial properties with tendencies to fibrillate and hence is known as a fibril-forming protein. Therefore, its behavior under different ambient conditions is of great importance. In this study, we conducted two 500000 ps molecular dynamics (MD simulations of human lysozyme in sodium dodecyl sulfate (SDS at two ambient temperatures. To achieve comparative results, we also performed two 500000 ps human lysozyme MD simulations in pure water as controls. The aim of this study was to provide further molecular insight into all interactions in the lysozyme-SDS complexes and to provide a perspective on the ability of human lysozyme to form amyloid fibrils in the presence of SDS surfactant molecules. SDS, which is an anionic detergent, contains a hydrophobic tail with 12 carbon atoms and a negatively charged head group. The SDS surfactant is known to be a stabilizer for helical structures above the critical micelle concentration (CMC [1]. During the 500000 ps MD simulations, the helical structures were maintained by the SDS surfactant above its CMC at 300 K, while at 370 K, human lysozyme lost most of its helices and gained β-sheets. Therefore, we suggest that future studies investigate the β-amyloid formation of human lysozyme at SDS concentrations above the CMC and at high temperatures.

  6. Micellization, interaction and thermodynamic study of butylated hydroxyanisole (synthetic antioxidant and sodium dodecyl sulfate in aqueous-ethanol solution at 25, 30 and 35 °C

    Directory of Open Access Journals (Sweden)

    Varun Bhardwaj

    2016-09-01

    Full Text Available Surfactants are found to enhance the diffusion significantly depending on hydrophobic/hydrophilic group lengths and the structure of the surfactant molecule. Aggregation properties of sodium dodecyl sulfate (SDS in the presence of butylated hydroxyanisole (synthetic antioxidant, at a range of temperatures (25, 30 and 35 °C have been measured by the conductometric study in aqueous-ethanolic composite solution. The experimental data of aqueous-ethanolic solutions as a function of SDS concentration ranging from 1 to 14 mM dm−3 show the presence of inflexion points indicating micellization and interaction mechanisms. Effect of temperature was also observed in increasing the CMC (Critical Micelle Concentration in the narrow composition. From the CMC values as a function of temperature, various thermodynamic parameters have been evaluated viz: (a the standard enthalpy change (ΔHm°, (b standard entropy change (ΔSm°, and (c standard Gibbs energy change (ΔGm°. The results showed that the presence of alcohol, as well as the composition of water + ethanol may have effect on thermodynamic parameters. The variation in these parameters with the concentration of surfactant or with the change in temperature suggests the manifestation of hydrophobic interactions in the studied system.

  7. Molecular Insight into Human Lysozyme and Its Ability to Form Amyloid Fibrils in High Concentrations of Sodium Dodecyl Sulfate: A View from Molecular Dynamics Simulations.

    Science.gov (United States)

    Jafari, Majid; Mehrnejad, Faramarz

    2016-01-01

    Changes in the tertiary structure of proteins and the resultant fibrillary aggregation could result in fatal heredity diseases, such as lysozyme systemic amyloidosis. Human lysozyme is a globular protein with antimicrobial properties with tendencies to fibrillate and hence is known as a fibril-forming protein. Therefore, its behavior under different ambient conditions is of great importance. In this study, we conducted two 500000 ps molecular dynamics (MD) simulations of human lysozyme in sodium dodecyl sulfate (SDS) at two ambient temperatures. To achieve comparative results, we also performed two 500000 ps human lysozyme MD simulations in pure water as controls. The aim of this study was to provide further molecular insight into all interactions in the lysozyme-SDS complexes and to provide a perspective on the ability of human lysozyme to form amyloid fibrils in the presence of SDS surfactant molecules. SDS, which is an anionic detergent, contains a hydrophobic tail with 12 carbon atoms and a negatively charged head group. The SDS surfactant is known to be a stabilizer for helical structures above the critical micelle concentration (CMC) [1]. During the 500000 ps MD simulations, the helical structures were maintained by the SDS surfactant above its CMC at 300 K, while at 370 K, human lysozyme lost most of its helices and gained β-sheets. Therefore, we suggest that future studies investigate the β-amyloid formation of human lysozyme at SDS concentrations above the CMC and at high temperatures.

  8. Sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE of urinary protein in acute kidney injury

    Directory of Open Access Journals (Sweden)

    Sufi M Suhail

    2011-01-01

    Full Text Available Recent experimental and clinical studies have shown the importance of urinary proteomics in acute kidney injury (AKI. We analyzed the protein in urine of patients with clinical AKI using sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE for its diagnostic value, and followed them up for 40 months to evaluate prognosis. Urine from 31 consecutive cases of AKI was analyzed with SDS-PAGE to determine the low, middle and high molecular weight proteins. Fractional excretion of sodium (FENa was estimated from serum and urine creatinine and sodium (Na. The cases were followed-up for 40 months from the end of the recruitment of study cases. Glomerular protein was higher in the hematuria group when compared with the non-hematuria group (P <0.04 and in the AKI group than in the acute on chronic renal failure (AKI-on-CRF group (P <0.002. Tubular protein was higher in the AKI-on-CRF group (P <0.003 than in the AKI group. Tubular protein correlated with FENa in groups with diabetes mellitus (DM, AKI-on-CRF, and without hematuria (P <0.03, P <0.02 and P <0.004, respectively. Pattern of protein did not differ between groups with and without DM and clinical acute tubular necrosis (ATN. At the end of 40 months follow-up, category with predominantly glomerular protein progressed to chronic renal failure (CRF or end-stage renal failure in higher proportion (P <0.05. In clinical AKI, we observed that glomerular protein dominated in cases with glomerular insult, as indicated by hematuria. Tubular protein was common in the study cases with CRF, DM and cases without hematuria. This indicates tubulo-interstitial injury for AKI in these cases. Patients with predominantly glomerular protein had an adverse outcome.

  9. Application and Mechanism of Anionic Collector Sodium Dodecyl Sulfate (SDS in Phosphate Beneficiation

    Directory of Open Access Journals (Sweden)

    Kun Sun

    2017-02-01

    Full Text Available Phosphate ore is a valuable strategic resource. Most phosphate ore in China is collophane. Utilization of mid-low grade collophane is necessary to maintain social sustainable development. The gravity-flotation combination separation process can be utilized to separate mid-low grade collophane, but the process consumes a large quantity of acid in the reverse stage. Sodium dodecyl sulfate (SDS was used as a dolomite collector in this study to reduce the acid consumption of collophane flotation. SDS effectively removed dolomite from the gravity concentrate when no other reagents were present. Flotation test results showed that, compared to the conventional gravity-flotation process, the proposed SDS-based process reduced phosphoric acid dosage from 6.1 kg/t to 3.9 kg/t with similar separation results. The SDS action mechanisms on dolomite were further investigated by zeta potential analysis, single mineral flotation tests, infrared spectrum detection, and theoretical analysis. The results indicate that the SDS adsorption on dolomite is mainly physical adsorption, and that favorable separation effects between collophane and dolomite may be attributed to physical adsorption and entrainment. In addition, it also indicates that the physical adsorption can be utilized to remove dolomite from phosphate on account of zeta potential differences when the separate feed is coarse.

  10. Thermodynamic selectivity of functional agents on zeolite for sodium dodecyl sulfate sequestration.

    Science.gov (United States)

    Leng, Ling; Wang, Jian; Qiu, Xianxiu; Zhao, Yanxiang; Yip, Yuk-Wang; Law, Ga-Lai; Shih, Kaimin; Zhou, Zhengyuan; Lee, Po-Heng

    2016-11-15

    This study proposes a thermodynamic approach to effectively select functional agents onto zeolite for sodium dodecyl sulfate (SDS) sequestration in greywater reuse. We combine isothermal titration calorimetry (ITC) and quantum chemistry simulation (QCS) to identify the interactions between SDS and agents at the molecular level. Three potential agents, cetyl trimethyl ammonium bromide (CTAB), N,N,N-trimethyltetradecan-1-aminium bromide (C14TAB), and 14-hydroxy-N,N,N-trimethyltetradecan-1-aminium bromide (C14HTAB), differ in carbon chain length and hydrophilic groups. The ITC titration of SDS with CTAB released the highest heat, followed by those with C14TAB and C14HTAB, as was the same trend for the amounts of SDS adsorbed by the respective functionalized-zeolites. Results suggest that the favorable SDS sorption occurred at the bilayer CTAB-zeolite is driven by enthalpy as similar as the SDS…CTAB interaction found, regardless of the contribution from electrostatic and/or hydrophobic behaviors, while the declined sorption is entropy-driven via the predominant hydrophobic interaction onto the monolayer CTAB-zeolite. The data presented here interpret the nature of molecularly thermodynamic quantities and enable the manipulation of sorption capacity optimization. Copyright © 2016 Elsevier B.V. All rights reserved.

  11. Microfluidic integration of Western blotting is enabled by electrotransfer-assisted sodium dodecyl sulfate dilution.

    Science.gov (United States)

    Hou, Chenlu; Herr, Amy E

    2013-01-07

    We integrate sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE) with subsequent antibody probing in a single, monolithic microdevice to realize microfluidic Western blotting. A hurdle to successful on-chip Western blotting lies in restoring antibody recognition of previously sized (denatured, reduced) proteins. To surmount this hurdle, we locally dilute free SDS from SDS-protein complexes using differential electromigration of the species during electrotransfer between SDS-PAGE and blotting regions of a microchamber. Local dilution of SDS minimizes re-association of SDS with proteins offering means to restore antibody binding affinity to proteins after SDS-PAGE. To achieve automated, programmable operation in a single instrument, we utilize a 1 × 2 mm(2) glass microchamber photopatterned with spatially distinct, contiguous polyacrylamide regions for SDS-PAGE, electrotransfer, and antibody blotting. Optimization of both the SDS-PAGE and electrotransfer conditions yields transfer distances of Western blot is completed in 180 s, with fully automated assay operation using programmable voltage control. After SDS-PAGE and electrotransfer, we observe ~80% capture of protein band mass on the blotting region for a model protein, C-reactive protein. This novel microfluidic Western blot approach introduces fine transport control for in-transit protein handling to form the basis for an automated, rapid alternative to conventional slab-gel Western blotting.

  12. The removal of Tartrazine dye by modified Alumina with sodium dodecyl sulfate from aqueous solutions: equilibrium and thermodynamic studies

    OpenAIRE

    A. Parchebaf Jadid; S. Sadeghi

    2017-01-01

    Edible colors are materials which in the case of adding to food and drinks cause transferring color to them. Most of these colors are not acceptable in terms of applying in human food and underlies various diseases like gastrointestinal disorders, renal, liver and blood toxicity. The goal of this study was investigating the efficiency of improved alumina by sodium dodecyl sulfate (SDS) in eliminating Tartrazine from aqueous environments. In this research, the impact of effective parameters su...

  13. Isolation of a strain of Pseudomonas putida capable of metabolizing anionic detergent sodium dodecyl sulfate (SDS).

    Science.gov (United States)

    Chaturvedi, V; Kumar, A

    2011-03-01

    Sodium Dodecyl Sulfate (SDS) is one of the most widely used anionic detergents. The present study deals with isolation and identification of SDS-degrading bacteria from a detergent contaminated pond situated in Varanasi city, India. Employing enrichment technique in minimal medium (PBM), SDS-degrading bacteria were isolated from pond water sample. Rate of degradation of SDS was studied in liquid PBM and also degradation of different concentrations of SDS was also studied to find out maximum concentration of SDS degraded by the potent isolates. Alkyl sulfatase activity (key enzyme in SDS degradation) was estimated in crude cell extracts and multiplicity of alkyl sulfatase was studied by Native PAGE Zymography. The potent isolate was identified by 16S rRNA sequence analysis. Using enrichment technique in minimal medium containing SDS as a sole carbon source, initially three SDS degrading isolates were recovered. However, only one isolate, SP3, was found to be an efficient degrader of SDS. It was observed that this strain could completely metabolize 0.1% SDS in 16 h, 0.2% SDS in 20 h and 0.3% SDS in 24 h of incubation. Specific activity of alkyl sulfatase was 0.087±0.004 µmol SDS/mg protein/min and Native PAGE Zymography showed presence of alkyl sulfatase of Rf value of 0.21. This isolate was identified as Pseudomonas putida strain SP3. This is the report of isolation of SDS-degrading strain of P. putida, which shows high rate of SDS degradation and can degrade up to 0.3% SDS. It appears that this isolate can be exploited for bioremediation of this detergent from water systems.

  14. Cadmium Immobilization in Soil using Sodium Dodecyl Sulfate Stabilized Magnetite Nanoparticles

    Directory of Open Access Journals (Sweden)

    Ahmad Farrokhian Firouzi

    2017-06-01

    Full Text Available Introduction Some methods of contaminated soils remediation reduces the mobile fraction of trace elements, which could contaminate groundwater or be taken up by soil organisms. Cadmium (Cd as a heavy metal has received much attention in the past few decades due to its potential toxic impact on soil organism activity and compositions. Cadmium is a soil pollutant of no known essential biological functions, and may pose threats to soil-dwelling organisms and human health. Soil contamination with Cd usually originates from mining and smelting activities, atmospheric deposition from metallurgical industries, incineration of plastics and batteries, land application of sewage sludge, and burning of fossil fuels. Heavy metal immobilization using amendments is a simple and rapid method for the reduction of heavy metal pollution. One way of the assessment of contaminated soils is sequential extraction procedure. Sequential extraction of heavy metals in soils is an appropriate way to determine soil metal forms including soluble, exchangeable, carbonate, oxides of iron and manganese, and the residual. Its results are valuable in prediction of bioavailability, leaching rate and elements transformation in contaminated agricultural soils. Materials and Methods The objective of this study was to synthesize magnetite nanoparticles (Fe3O4 stabilized with sodium dodecyl sulfate (SDS and to investigate the effect of its different percentages (0, 1, 2.5, 5, and 10% on the different fractions of cadmium in soil by sequential extraction method. The nanoparticles were synthesized following the protocol described by Si et al. (19. The investigations were carried out with a loamy sand topsoil. Before use, the soil was air-dried, homogenized and sieved (

  15. Thermodynamic selectivity of functional agents on zeolite for sodium dodecyl sulfate sequestration

    Energy Technology Data Exchange (ETDEWEB)

    Leng, Ling; Wang, Jian [Department of Civil and Environmental Engineering, The Hong Kong Polytechnic University, Hung Hom, Kowloon, Hong Kong SAR (China); Qiu, Xianxiu; Zhao, Yanxiang; Yip, Yuk-Wang; Law, Ga-Lai [Department of Applied Biology and Chemical Technology, State Key Laboratory of Chirosciences, The Hong Kong Polytechnic University, Hung Hom, Kowloon, Hong Kong SAR (China); Shih, Kaimin; Zhou, Zhengyuan [Department of Civil Engineering, The University of Hong Kong, Pokfulam Road, Hong Kong, Hong Kong SAR (China); Lee, Po-Heng, E-mail: poheng76@gmail.com [Department of Civil and Environmental Engineering, The Hong Kong Polytechnic University, Hung Hom, Kowloon, Hong Kong SAR (China)

    2016-11-15

    Highlights: • A thermodynamic approach to select a functional agent for adsorbent is proposed. • ITC and QCS were used to interpret the interaction between adsorbate and agent. • The interaction identifies the adsorption mechanism and performance. • This approach enables the manipulation of adsorption capacity optimization. - Abstract: This study proposes a thermodynamic approach to effectively select functional agents onto zeolite for sodium dodecyl sulfate (SDS) sequestration in greywater reuse. We combine isothermal titration calorimetry (ITC) and quantum chemistry simulation (QCS) to identify the interactions between SDS and agents at the molecular level. Three potential agents, cetyl trimethyl ammonium bromide (CTAB), N,N,N-trimethyltetradecan-1-aminium bromide (C{sub 14}TAB), and 14-hydroxy-N,N,N-trimethyltetradecan-1-aminium bromide (C{sub 14}HTAB), differ in carbon chain length and hydrophilic groups. The ITC titration of SDS with CTAB released the highest heat, followed by those with C{sub 14}TAB and C{sub 14}HTAB, as was the same trend for the amounts of SDS adsorbed by the respective functionalized-zeolites. Results suggest that the favorable SDS sorption occurred at the bilayer CTAB-zeolite is driven by enthalpy as similar as the SDS…CTAB interaction found, regardless of the contribution from electrostatic and/or hydrophobic behaviors, while the declined sorption is entropy-driven via the predominant hydrophobic interaction onto the monolayer CTAB-zeolite. The data presented here interpret the nature of molecularly thermodynamic quantities and enable the manipulation of sorption capacity optimization.

  16. Development of a Robust Method for Simultaneous Quantification of Polymer (HPMC) and Surfactant (Dodecyl β-D-Maltoside) in Nanosuspensions.

    Science.gov (United States)

    Patel, Salin Gupta; Bummer, Paul M

    2016-10-01

    This report describes the development of a chromatographic method for the simultaneous quantification of a polymer, hydroxypropyl methylcellulose (HPMC), and a surfactant, dodecyl β-D-maltoside (DM), that are commonly used in the physical stabilization of pharmaceutical formulations such as nanosuspensions and solid dispersions. These excipients are often challenging to quantify due to the lack of chromophores. A reverse phase size exclusion chromatography (SEC) with evaporative light scattering detector (ELSD) technique was utilized to develop an accurate and robust assay for the simultaneous quantification of HPMC and DM in a nanosuspension formulation. The statistical design of experiments was used to determine the influence of critical ELSD variables including temperature, pressure, and gain on accuracy, precision, and sensitivity of the assay. A robust design space was identified where it was determined that an increase in the temperature of the drift tube and gain of the instrument increased the accuracy and precision of the assay and a decrease in the nebulizer pressure value increased the sensitivity of the assay. In the optimized design space, response data showed that the assay could quantify HPMC and DM simultaneously with good accuracy, precision, and reproducibility. Overall, SEC-ELSD proved to be a powerful technique for the simultaneous quantification of HPMC and DM. This technique can be used to quantify the amount of HPMC and DM in nanosuspensions, which is critical to understanding their effects on the physical stability of nanosuspensions.

  17. Isolation and Characterization of Pseudomonas spp. Strains That Efficiently Decompose Sodium Dodecyl Sulfate

    Directory of Open Access Journals (Sweden)

    Ewa M. Furmanczyk

    2017-11-01

    Full Text Available Due to their particular properties, detergents are widely used in household cleaning products, cosmetics, pharmaceuticals, and in agriculture as adjuvants tailoring the features of pesticides or other crop protection agents. The continuously growing use of these various products means that water soluble detergents have become one of the most problematic groups of pollutants for the aquatic and terrestrial environments. Thus it is important to identify bacteria having the ability to survive in the presence of large quantities of detergent and efficiently decompose it to non-surface active compounds. In this study, we used peaty soil sampled from a surface flow constructed wetland in a wastewater treatment plant to isolate bacteria that degrade sodium dodecyl sulfate (SDS. We identified and initially characterized 36 Pseudomonas spp. strains that varied significantly in their ability to use SDS as their sole carbon source. Five isolates having the closest taxonomic relationship to the Pseudomonas jessenii subgroup appeared to be the most efficient SDS degraders, decomposing from 80 to 100% of the SDS present in an initial concentration 1 g/L in less than 24 h. These isolates exhibited significant differences in degree of SDS degradation, their resistance to high detergent concentration (ranging from 2.5 g/L up to 10 g/L or higher, and in chemotaxis toward SDS on a plate test. Mass spectrometry revealed several SDS degradation products, 1-dodecanol being dominant; however, traces of dodecanal, 2-dodecanol, and 3-dodecanol were also observed, but no dodecanoic acid. Native polyacrylamide gel electrophoresis zymography revealed that all of the selected isolates possessed alkylsulfatase-like activity. Three isolates, AP3_10, AP3_20, and AP3_22, showed a single band on native PAGE zymography, that could be the result of alkylsulfatase activity, whereas for isolates AP3_16 and AP3_19 two bands were observed. Moreover, the AP3_22 strain exhibited a band

  18. Solid phase microextraction-high performance liquid chromatographic determination of octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX) and hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) in the presence of sodium dodecyl sulfate surfactant.

    Science.gov (United States)

    Malik, Ashok Kumar; Rai, Parmod Kumar

    2008-07-01

    A simple and sensitive method has been developed using preconcentration technique solid phase microextraction (SPME) and analytical technique HPLC-UV for the determination of octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX) and hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) from the environmental samples. Aqueous solution of anionic surfactant SDS was used for the extraction of both nitramine high explosives, viz., HMX and RDX from soil samples which were subsequently sorbed on SPME fiber. The static desorption was carried out in the desorption chamber of the SPME-HPLC interface in the presence of mobile phase ACN/methanol/water (30:35:35) and the subsequent chromatographic analysis at a flow rate of 0.5 mL/min and detection at 230 nm. For this purpose, a C(18), 5 microm RP analytical column was used as a separation medium in this method. Several parameters relating to SPME, e.g., adsorption/desorption time, concentration of salt, stirring rate, etc., were optimized. The method was linear over the range of 20-400 ng/mL for HMX and RDX standards in the presence of surfactant in aqueous phase, respectively. The correlation coefficient (R(2)) for HMX and RDX are 0.9998 and 0.9982, respectively. With SPME, the detection limits (S/N = 3) in ng/mL are 0.05 and 0.1 for HMX and RDX, respectively in the presence of the SDS surfactant. The developed method has been applied successfully to the analysis of real environmental samples like bore well water, river water, and ground alluvial soil.

  19. Fluorescence enhancement effect for the determination of curcumin with yttrium(III)-curcumin-sodium dodecyl benzene sulfonate system

    International Nuclear Information System (INIS)

    Wang Feng; Huang Wei; Wang Yanwei

    2008-01-01

    It is found that the fluorescence of curcumin is greatly enhanced by yttrium(III) (Y 3+ ) in the presence of sodium dodecyl benzene sulfonate. Based on this, a sensitive fluorimetric method for the determination of curcumin in aqueous solution is proposed. In the potassium hydrogen phthalate (KHP) buffer, the fluorescence intensity of curcumin is proportional to the concentration of curcumin in the range of 7.37x10 -4 -0.18, 0.18-2.95 μg mL -1 and the detection limit is 0.1583 ng mL -1 . The actual samples are satisfactorily determined. In addition, the interaction mechanism is also studied

  20. Hydrogels of sodium alginate in cationic surfactants: Surfactant dependent modulation of encapsulation/release toward Ibuprofen.

    Science.gov (United States)

    Jabeen, Suraya; Chat, Oyais Ahmad; Maswal, Masrat; Ashraf, Uzma; Rather, Ghulam Mohammad; Dar, Aijaz Ahmad

    2015-11-20

    The interaction of cetyltrimethylammoium bromide (CTAB) and its gemini homologue (butanediyl-1,4-bis (dimethylcetylammonium bromide), 16-4-16 with biocompatible polymer sodium alginate (SA) has been investigated in aqueous medium. Addition of K2CO3 influences viscoelastic properties of surfactant impregnated SA via competition between electrostatic and hydrophobic interactions. Viscosity of these polymer-surfactant systems increases with increase in concentration of K2CO3, and a cryogel is formed at about 0.5M K2CO3 concentration. The thermal stability of gel (5% SA+0.5M K2CO3) decreases with increase in surfactant concentration, a minimum is observed with increase in 16-4-16 concentration. The impact of surfactant addition on the alginate structure vis-à-vis its drug loading capability and release thereof was studied using Ibuprofen (IBU) as the model drug. The hydrogel with 16-4-16 exhibits higher IBU encapsulation and faster release in comparison to the one containing CTAB. This higher encapsulation-cum-faster release capability has been related to micelle mediated solubilization and greater porosity of the hydrogel with gemini surfactant. Copyright © 2015 Elsevier Ltd. All rights reserved.

  1. Effect of protic ionic liquids (PILs) on the formation of non-ionic dodecyl poly(ethylene oxide) surfactant self-assembly structures and the effect of these surfactants on the nanostructure of PILs.

    Science.gov (United States)

    Greaves, Tamar L; Mudie, Stephen T; Drummond, Calum J

    2011-12-07

    The ability of a series of non-ionic dodecyl poly(ethylene oxide) surfactants to form micelles in a variety of protic ionic liquids (PILs) was investigated using small and wide angle X-ray scattering (SAXS/WAXS). The C(12)E(n) surfactants with n = 3-8 were examined in PILs which contained either an ethyl, diethyl, triethyl, butyl, pentyl, ethanol or pentanol-ammonium cation in conjunction with either a nitrate or formate anion. The ability of the PILs to support micelles of these surfactants was highly dependent on their liquid nanostructure. The PILs containing hydroxyl groups on the cations were not nanostructured and had very low surfactant solubility (surfactant solubility, but due to the greater hydrocarbon solubility they had insufficient drive from the "solvophobic effect" to enable micelle formation. The PILs of ethylammonium nitrate (EAN), propylammonium nitrate (PAN), diethylammonium formate (DEAF) and triethylammonium formate (TEAF) had smaller non-polar domains, and all supported micelle formation below 20 wt% surfactant. The critical micelle concentration (CMC) of surfactants in EAN were two orders of magnitude greater than in water. The minimum molecular areas of the poly(ethylene oxide) head groups at the air/ionic liquid interface, A(min), were significantly larger in EAN than in water. The SAXS patterns from the micelles present in EAN fitted well to ellipsoids, whereas the micelles present in PAN fitted well to spheres. The nanostructure of select PILs was also influenced by the presence of surfactants.

  2. Influence of sodium dodecyl sulfate on swelling, erosion and release behavior of HPMC matrix tablets containing a poorly water-soluble drug.

    Science.gov (United States)

    Zeng, Aiguo; Yuan, Bingxiang; Fu, Qiang; Wang, Changhe; Zhao, Guilan

    2009-01-01

    The effect of sodium dodecyl sulfate (SDS) on the swelling, erosion and release behavior of HPMC matrix tablets was examined. Swelling and erosion of HPMC matrix tablets were determined by measuring the wet and subsequent dry weights of matrices. The rate of uptake of the dissolution medium by the matrix was quantified using a square root relationship whilst the erosion of the polymer was described using the cube root law. The extent of swelling decreased with increasing SDS concentrations in the dissolution medium but the rate of erosion was found to follow a reverse trend. Such phenomena might have been caused by the attractive hydrophobic interaction between HPMC and SDS as demonstrated by the cloud points of the solutions containing both the surfactant and polymer. Release profiles of nimodipine from HPMC tablets in aqueous media containing different concentrations of SDS were finally studied. Increasing SDS concentrations in the medium was shown to accelerate the release of nimodipine from the tablets, possibly due to increasing nimodipine solubility and increasing rate of erosion by increasing SDS concentrations in the dissolution medium.

  3. Sodium dodecyl sulfate coated γ-alumina support modified by a new Schiff base for solid phase extraction and flame-AAS determination of lead and copper ions

    Directory of Open Access Journals (Sweden)

    Ardeshir Shokrollahi

    2013-01-01

    Full Text Available A simple and fast approach for solid phase extraction is herein described, and used to determine trace amounts of Pb2+ and Cu2+ metal ions. The solid phase support is sodium dodecyl sulfate (SDS-coated γ-alumina modified with bis(2-hydroxy acetophenone-1,6-hexanediimine (BHAH ligand. The adsorbed ions were stripped from the solid phase by 6 mL of 4 M nitric acid as eluent. The eluting solution was analyzed by flame atomic absorption spectrometry (FAAS. The sorption recovery of metal ions was investigated with regard to the effects of pH, amount of ligand, γ-alumina and surfactant and the amount and type of eluent. Complexation of BHAH with Pb2+ or Cu2+ ions was examined via spectrophotometry using the HypSpec program. The detection limit for Cu2+ was 7.9 µg L-1 with a relative standard deviation of 1.67%, while that for Pb2+ was 6.4 µg L-1 with a relative standard deviation of 1.64%. A preconcentration factor of 100 was achieved for these ions. The method was successfully applied to determine analyte concentrations in samples of liver, parsley, cabbage, and water.

  4. Studies on interaction of poly(sodium acrylate) and poly(sodium styrenesulfonate) with cationic surfactants: effects of polyelectrolyte molar mass, chain flexibility, and surfactant architecture.

    Science.gov (United States)

    Wang, Hao; Wang, Yilin

    2010-08-19

    Isothermal titration microcalorimetry, turbidity, and steady-state fluorescence measurements have been used to study interactions of cationic ammonium gemini surfactant (C(12)C(6)C(12)Br(2)) and single-chain surfactant dodecyltrimethylammonium bromide (DTAB) with anionic polyelectrolytes poly(sodium styrenesulfonates) (NaPSS) and poly(sodium acrylates) (NaPAA) with different molar masses. Without any surfactants, NaPSS with lower molar mass has already self-aggregated into aggregates, whereas NaPAA has no aggregation at any molar mass. All of the polyelectrolytes show a remarkable interaction with the cationic surfactants. Compared with DTAB, C(12)C(6)C(12)Br(2) can bind to NaPSS and NaPAA at a very low concentration and has stronger interactions with NaPSS and NaPAA. The flexible NaPAA shows moderately endothermic enthalpies while interacting with the surfactants, but the interaction of the stiff NaPSS with the surfactants exhibits highly exothermic enthalpies. Moreover, the interaction of the stiff NaPSS with the surfactants strongly depends on the polyelectrolyte molar mass, but the polyelectrolyte molar mass almost does not affect the interaction of the flexible NaPAA with the surfactants. Especially, the effect of the polyelectrolyte molar mass becomes more significant when the polyelectrolytes interact with gemini surfactant than with single-chain surfactant. It is revealed that the effects of polyelectrolyte molar mass, chain flexibility, and surfactant architecture on surfactant/polyelectrolyte interactions confine each other.

  5. Microchamber Western blotting using poly-L-lysine conjugated polyacrylamide gel for blotting of sodium dodecyl sulfate coated proteins.

    Science.gov (United States)

    Chung, Minsub; Kim, Dohyun; Herr, Amy E

    2013-08-20

    We report a novel strategy to immobilize sodium dodecyl sulfate (SDS)-coated proteins for fully integrated microfluidic Western blotting. Polyacrylamide gel copolymerized with a cationic polymer, poly-L-lysine, effectively immobilizes all sized proteins after sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE), and enables SDS-PAGE and subsequent immuno-probing in an automated microfluidic chip. Design of a poly-l-lysine conjugated polyacrylamide gel allows optimization of SDS-protein immobilization strength in the blotting gel region of the microchamber. The dependence of protein capture behavior on both the concentration of copolymerized charges and poly-lysine length is studied and gives important insight into an electrostatic immobilization mechanism. Based on analysis of protein conformation, the immobilized proteins bind with partner antibody after SDS dilution. We demonstrate each step of the microchamber Western blot, including injection, separation, transfer, immobilization, blocking, and immunoblot. The approach advances microfluidic protein immunoblotting, which is directly relevant to the widely-used SDS-PAGE based slab-gel Western blot, while saving sample volume, labor, and assay time.

  6. The removal of Tartrazine dye by modified Alumina with sodium dodecyl sulfate from aqueous solutions: equilibrium and thermodynamic studies

    Directory of Open Access Journals (Sweden)

    A. Parchebaf Jadid

    2017-11-01

    Full Text Available Edible colors are materials which in the case of adding to food and drinks cause transferring color to them. Most of these colors are not acceptable in terms of applying in human food and underlies various diseases like gastrointestinal disorders, renal, liver and blood toxicity. The goal of this study was investigating the efficiency of improved alumina by sodium dodecyl sulfate (SDS in eliminating Tartrazine from aqueous environments. In this research, the impact of effective parameters such as initial concentration of Tartrazine, time, pH, alumina dose and SDS value were studied in order to approach an optimal condition for eliminating the color. Also, absorption behavior was evaluated by Freundlich and Langmuir isotherms. The highest efficiency of Tartrazine elimination in the solution resulted in optimal pH of 2, the amount of adsorbent 1.5 g/L, 16 min duration and value 0.04 SDS g/l which was obtained for dye concentration 5 mg/L about 94.13%. Also, results suggested that Tartrazine absorption follows Langmuir isotherm (R2 = 0.9867. Obtained results from thermodynamic studies such as Gibbs free energy (-5.728 Kj/mol and enthalpy (-85.86 Kj/mol and entropy (-271.102 J/mol.K also suggested that the absorption process was exothermic. The results of this research suggested that improved alumina by sodium dodecyl sulfate had a relative good capability in Tartrazine elimination from aqueous environments. Thus

  7. [Strengthening Effects of Sodium Salts on Washing Kerosene Contaminated Soil with Surfactants].

    Science.gov (United States)

    Huang, Zhao-lu; Chen, Quan-yuan; Zhou, Juan; Xie, Mo-han

    2015-05-01

    The impact of sodium salt on kerosene contaminated soil washing with surfactants was investigated. The results indicated that sodium silicate greatly enhanced the washing efficiency of SDS. Sodium tartrate can largely enhance the washing efficiency of SDBS and Brij35. Sodium salts can enhance the washing efficiency on kerosene contaminated with TX-100. No significant differences were observed between different sodium salts. Sodium salt of humic acid and sodium silicate had similar enhancement on kerosene contaminated soil washing with saponin. Sodium humate can be a better choice since its application can also improve soil quality. The enhancement of sodium silicate on kerosene contaminated soil washing with Tw-80 increased with the increase of Tw-80 dosage. However, the impact of sodium chloride and sodium tartrate was opposite to sodium silicate. Sodium salts can reduce surface tension and critical micelle concentration of ionic surfactants to enhance the washing. Sodium salts can also reduce re-adsorption of oil to soil with nonionic surfactants to enhance the washing. Kerosene contamination can increase the contact angle of soil, which indicated the increase of hydrophilicity of soil. Washing with surfactants can reduce the hydrophilicitiy of soil according to contact angle measurement, which indicated that kerosene contaminated soil remediation with surfactant can also benefit nutrient and water transportation in the contaminated soil.

  8. NANOSIZE STRUCTURE OF SELF-ASSEMBLY SODIUM DODECYL SULFATE: A STUDY BY SMALL ANGLE NEUTRON SCATTERING (SANS

    Directory of Open Access Journals (Sweden)

    Edy Giri Rachman Putra

    2010-06-01

    Full Text Available Small Angle Neutron Scattering (SANS investigation on the self-assembly sodium dodecyl sulfate (SDS molecules as a function of concentration and additives has been carried out. SANS spectrometer which has been completely installed at the neutron scattering laboratory (NSL BATAN in Serpong, Indonesia has played most important role to determine the growth (size and also the shapes of a micelle structure. In this works we report that spherical micelle structure with a radius of 16.7 Å will transform to ellipsoidal or rod-like micelle structure with the long axis extends up to 50 Å by increasing the concentration of SDS. Similar to that the micelle structures change by addition of salt in SDS micellar solutions.   Keywords: nanostructure, micelle, self-assembly

  9. Quantitation of yeast total proteins in sodium dodecyl sulfate-polyacrylamide gel electrophoresis sample buffer for uniform loading.

    Science.gov (United States)

    Sheen, Hyukho

    2016-04-01

    Proteins in sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) sample buffer are difficult to quantitate due to SDS and reducing agents being in the buffer. Although acetone precipitation has long been used to clean up proteins from detergents and salts, previous studies showed that protein recovery from acetone precipitation varies from 50 to 100% depending on the samples tested. Here, this article shows that acetone precipitates proteins highly efficiently from SDS-PAGE sample buffer and that quantitative recovery is achieved in 5 min at room temperature. Moreover, precipitated proteins are resolubilized with urea/guanidine, rather than with SDS. Thus, the resolubilized samples are readily quantifiable with Bradford reagent without using SDS-compatible assays. Copyright © 2016 Elsevier Inc. All rights reserved.

  10. Voltammetric Determination of Ivabradine Hydrochloride Using Multiwalled Carbon Nanotubes Modified Electrode in Presence of Sodium Dodecyl Sulfate

    Directory of Open Access Journals (Sweden)

    Ali Kamal Attia

    2017-04-01

    Full Text Available Purpose: A new sensitive sensor was fabricated for the determination of ivabradine hydrochloride (IH based on modification with multiwalled carbon nanotubes using sodium dodecyl sulfate as micellar medium to increase the sensitivity. Methods: The electrochemical behavior of IH was studied in Britton-Robinson buffer (pH: 2.0-11.0 using cyclic and differential pulse voltammetry. Results: The voltammetric response was linear over the range of 3.984 x 10-6-3.475 x 10-5 mol L-1. The limits of detection and quantification were found to be 5.160 x 10-7 and 1.720 x 10-6 mol L-1, respectively. Conclusion: This method is suitable for determination of IH in tablets and plasma.

  11. Voltammetric Determination of Ivabradine Hydrochloride Using Multiwalled Carbon Nanotubes Modified Electrode in Presence of Sodium Dodecyl Sulfate.

    Science.gov (United States)

    Attia, Ali Kamal; Abo-Talib, Nisreen Farouk; Tammam, Marwa Hosny

    2017-04-01

    Purpose: A new sensitive sensor was fabricated for the determination of ivabradine hydrochloride (IH) based on modification with multiwalled carbon nanotubes using sodium dodecyl sulfate as micellar medium to increase the sensitivity. Methods: The electrochemical behavior of IH was studied in Britton-Robinson buffer (pH: 2.0-11.0) using cyclic and differential pulse voltammetry. Results: The voltammetric response was linear over the range of 3.984 x 10 -6 -3.475 x 10 -5 mol L -1 . The limits of detection and quantification were found to be 5.160 x 10 -7 and 1.720 x 10-6 mol L -1 , respectively. Conclusion: This method is suitable for determination of IH in tablets and plasma.

  12. Foam capacity and stability of Sodium Dodecyl Sulfate (SDS) on the presence of contaminant coffee and Cd ions in solution

    Science.gov (United States)

    Haryanto, B.; Chang, C. H.; Kuo, A. T.; Siswarni, M. Z.; Sinaga, T. M. A.

    2018-02-01

    In this study, the effect of the coffee colloidal particle and Cd ion contaminant on the foam capacity and stability of sodium dodecyl sulfate (SDS) solution was investigated. The foam was generated by using a foam generator. The foam capacity of SDS was first evaluated at different concentrations. After the foam capacity reaching a constant value, the foam stability was then measured by flowing to a column. The results showed that the presence the coffee colloidal particles or Cd ions in the solution would decrease the foam capacity and stability of SDS. In addition, the decreased foam capacity and stability was more pronounced in the presence of coffee colloidal particles than Cd ions. The colloidal particles may have stronger interaction with SDS and thus reduce the formation of the foam.

  13. Adsorption of sodium dodecyl sulfate onto precipitate in treatment of vat dark blue BO by dissolved air flotation.

    Science.gov (United States)

    Xia, Hongyun; Zhao, Xuyun; Zhao, Xiang; Yao, Ping; Zhang, Haoyu

    2017-07-03

    Vat dark blue BO-simulated wastewater was treated by dissolved air flotation (DAF). In this process, the interactions of sodium dodecyl sulfate (SDS) and resulting DAF process precipitates were investigated by infrared spectroscopy and kinetic methods. Fourier transform infrared analysis revealed that γ values (cm -1 ) for asymmetric and symmetric stretching vibrations of CH 2 groups for SDS-treated precipitation shifted toward higher in comparison to pure SDS, showing strong SDS and precipitate interactions. This showed the chemical adsorption of SDS onto precipitate surfaces. Adsorption data were well described by a pseudo-second-order model, with an adsorption activation energy of 42.602 kJ mol -1 , further predicting an SDS chemisorption uptake process by the precipitate. SDS could be considered as one of the most efficient flotation agents for the removal of vat dark blue BO in DAF processing.

  14. Improving sodium dodecyl sulfate polyacrylamide gel electrophoresis detection of low-abundance protein samples by rapid freeze centrifugation.

    Science.gov (United States)

    Virgen-Ortíz, J J; Ibarra-Junquera, V; Escalante-Minakata, P; Osuna-Castro, J A; Ornelas-Paz, J de J; Mancilla-Margalli, N A; Castañeda-Aguilar, R L

    2013-12-15

    This work presents a rapid and simple freeze centrifugation method to concentrate dilute protein solutions for detection by sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE) Coomassie blue staining. Moreover, a simple way to assemble a cryoconcentration device is presented, and its use is discussed. Commercial purified protein standard and an enzyme with high fructosyltransferase (FTase) activity, coming from target fractions obtained by chromatographic separation, were used as an example. FTase, coming directly from the chromatographic fractions, was difficult to view through SDS-PAGE analysis; however, it was easily visualized, and its activity was enhanced, after the application of the freeze centrifugation protocol presented here. Copyright © 2013 Elsevier Inc. All rights reserved.

  15. Exposure of RML scrapie agent to a sodium percarbonate-based product and sodium dodecyl sulfate renders PrPSc protease sensitive but does not eliminate infectivity.

    Science.gov (United States)

    Smith, Jodi D; Nicholson, Eric M; Foster, Gregory H; Greenlee, Justin J

    2013-01-11

    Prions, the causative agents of the transmissible spongiform encephalopathies, are notoriously difficult to inactivate. Current decontamination recommendations by the World Health Organization include prolonged exposure to 1 N sodium hydroxide or > 20,000 ppm sodium hypochlorite, or autoclaving. For decontamination of large stainless steel surfaces and equipment as in abattoirs, for example, these methods are harsh or unsuitable. The current study was designed to evaluate the effectiveness of a commercial product containing sodium percarbonate to inactivate prions. Samples of mouse brain infected with a mouse-adapted strain of the scrapie agent (RML) were exposed to a sodium percarbonate-based product (SPC-P). Treated samples were evaluated for abnormal prion protein (PrPSc)-immunoreactivity by western blot analysis, and residual infectivity by mouse bioassay. Exposure to a 21% solution of SPC-P or a solution containing either 2.1% or 21% SPC-P in combination with sodium dodecyl sulfate (SDS) resulted in increased proteinase K sensitivity of PrPSc. Limited reductions in infectivity were observed depending on treatment condition. A marginal effect on infectivity was observed with SPC-P alone, but an approximate 2-3 log10 reduction was observed with the addition of SDS, though exposure to SDS alone resulted in an approximate 2 log10 reduction. This study demonstrates that exposure of a mouse-adapted scrapie strain to SPC-P does not eliminate infectivity, but does render PrPSc protease sensitive.

  16. SODIUM DI-N-DODECYL PHOSPHATE VESICLES IN AQUEOUS-SOLUTION - EFFECTS OF ETHANOL, PROPANOL, AND TETRAHYDROFURAN ON THE GEL TO LIQUID-PHASE TRANSITION

    NARCIS (Netherlands)

    BLANDAMER, MJ; BRIGGS, B; BUTT, MD; WATERS, M; CULLIS, PM; ENGBERTS, JBFN; HOEKSTRA, D; MOHANTY, RK

    1994-01-01

    For aqueous solutions containing vesicles formed by sodium di-n-dodecyl phosphate, the gel to liquid-crystal transition occurs near 35 degrees C, the temperature T-m. When ethanol is added, T-m decreases, but the scan shows evidence of several transitions as more alcohol is added. The effect of

  17. SODIUM DODECYL-SULFATE INDUCED ENHANCEMENT OF THE VISCOSITY AND VISCOELASTICITY OF AQUEOUS-SOLUTIONS OF POLY(ETHYLENE OXIDE) - A RHEOLOGICAL STUDY ON POLYMER MICELLE INTERACTION

    NARCIS (Netherlands)

    BRACKMAN, JC

    A large enhancement of the viscosity and the viscoelasticity of aqueous solutions of high molecular weight poly(ethylene oxide) (PEO) has been observed upon addition of sodium dodecyl sulfate (SDS). The changes in apparent viscosity, in the parameters for the power law model of non-Newtonian

  18. Molecular Level Understanding of Sodium Dodecyl Sulfate (SDS) Induced Sol-Gel Transition of Pluronic F127 Using Fisetin as a Fluorescent Molecular Probe.

    Science.gov (United States)

    Mishra, Jhili; Swain, Jitendriya; Mishra, Ashok Kumar

    2018-01-11

    The thermoreversible sol-gel transition of pluronic F127 is markedly altered even with addition of submicellar concentration of sodium dodecyl sulfate (SDS) surfactant. Multiple fluorescence parameters like fluorescence intensity, fluorescence anisotropy and fluorescence lifetime of both the prototropic forms (anion (A - *) and phototautomer FT*) of the photoprototropic fluorescent probe fisetin has been efficiently used to understand the molecular level properties like polarity and microviscosity of the PF127-SDS system as a function of temperature. The SDS-induced increase in the interfacial hydrophobicity level is seen to affect the sol-gel phase transition of PF127 (21-18 °C). The E T (30) polarity parameter value of anionic emission of fisetin suggests that there is a considerable decrease in the polarity of the PF127 medium with increase in temperature and with the addition of SDS. The microviscosity progressively increases from ∼5 mPa s (sol state, 10 °C) to ∼22.01 mPa s (gel state 35 °C) in aqueous solution of PF127. The variation in microviscosity with addition of SDS in PF127-SDS mixed system is significant in sol phase whereas in gel phase this variation is significantly less. Temperature dependent fluorescence lifetime of FT* indicates that there is heterogeneity in distribution of fisetin molecules at different domains of PF127. This work also show-cases the sensitivity of fisetin toward change in polarity and change in sol-gel transition temperature of copolymer PF127 with variation in temperature (both forward and reverse directions) and SDS.

  19. Control of pathogens in biofilms on the surface of stainless steel by levulinic acid plus sodium dodecyl sulfate.

    Science.gov (United States)

    Chen, Dong; Zhao, Tong; Doyle, Michael P

    2015-08-17

    The efficacy of levulinic acid (LVA) plus sodium dodecyl sulfate (SDS) to remove or inactivate Listeria monocytogenes, Salmonella Typhimurium, and Shiga toxin-producing Escherichia coli (STEC) in biofilms on the surface of stainless steel coupons was evaluated. Five- or six-strain mixtures (ca. 9.0 log CFU/ml) of the three pathogens were separately inoculated on stainless steel coupons. After incubation at 21 °C for 72 h, the coupons were treated for 10 min by different concentrations of LVA plus SDS (0.5% LVA+0.05% SDS, 1% LVA+0.1% SDS, and 3% LVA+2% SDS) and other commonly used sanitizers, including a commercial quaternary ammonium-based sanitizer (150 ppm), lactic acid (3%), sodium hypochlorite (100 ppm), and hydrogen peroxide (2%). The pathogens grew in the biofilms to ca. 8.6 to 9.3 log CFU/coupon after 72 h of incubation. The combined activity of LVA with SDS was bactericidal in biofilms for cells of the three pathogens evaluated, with the highest concentrations (3% LVA+2% SDS) providing the greatest log reduction. Microscopic images indicated that the cells were detached from the biofilm matrix and the integrity of cell envelopes were decreased after the treatment of LVA plus SDS. This study is conducive to better understanding the antimicrobial behavior of LVA plus SDS to the foodborne pathogens within biofilms. Copyright © 2015 Elsevier B.V. All rights reserved.

  20. Diffusion-controlled evaporation of sodium dodecyl sulfate solution drops placed on a hydrophobic substrate.

    Science.gov (United States)

    Doganci, Merve Dandan; Sesli, Belma Uyar; Erbil, H Yildirim

    2011-10-15

    In this work, the effect of SDS anionic surfactant on the diffusion-controlled evaporation rate of aqueous solution drops placed on TEFLON-FEP substrate was investigated with 11 different SDS concentrations. Drop evaporation was monitored in a closed chamber having a constant RH of 54-57% by a video camera. The initial contact angle, θ(i) decreased from 104±2° down to 68±1° due to the adsorption of SDS both at the water-air and the solid-water interfaces. The adsorption of SDS on the solid surface was found to be 76% of that of its adsorption at the water-air interface by applying Lucassen-Reynders approach. An equation was developed for the comparison of the evaporation rates of drops having different θ(i) on the same substrate. It was found that the addition of SDS did not alter the drop evaporation rate considerably for the first 1200 s for all the SDS concentrations. The main difference was found to be the change of the mode of drop evaporation by varying the SDS concentration. The constant θ mode was operative up to 80 mM SDS concentration, whereas constant contact area mode was operative after 200 mM SDS concentrations due to rapid drop pining on the substrate. Copyright © 2011 Elsevier Inc. All rights reserved.

  1. Effect of sodium sulfite, sodium dodecyl sulfate, and urea on the molecular interactions and properties of whey protein isolate-based films

    Science.gov (United States)

    Schmid, Markus; Prinz, Tobias K.; Stäbler, Andreas; Sängerlaub, Sven

    2016-12-01

    Whey protein coatings and cast films are promising for use as food packaging materials. Ongoing research is endeavoring to reduce their permeability. The intention of this study was to evaluate the effect of the reactive additives sodium sulfite, sodium dodecyl sulfate (SDS), and urea on the oxygen barrier, water vapor barrier, and protein solubility of whey protein cast films. The concentration of the reactive additives was 1 to 20 wt.-%. Dried whey protein cast films were used as substrate materials. The water vapor transmission rate, the oxygen permeability, and the protein solubility were measured. Effective diffusion coefficients and effective sorption coefficients were calculated from the results of the water vapor sorption experiments. The presence of sodium sulfite resulted in an increased number of hydrophobic interactions and hydrogen bonds and a slightly decreased number of disulfide bonds. The oxygen permeability decreased from 68 to 46 cm³ (STP / standard temperature and pressure) 100 µm (m² d bar)-1 for 1 wt.-% SDS in the whey protein cast film. The water vapor transmission rate decreased from 165 to 44 g 100 µm (m² d)-1 measured at 50 to 0 % r. h. for 20 wt.-% SDS in the whey protein cast film. The reduction in the water vapor transmission rate correlated with the lower effective diffusion coefficient.

  2. Structural Studies of Protein-Surfactant Complexes

    International Nuclear Information System (INIS)

    Chodankar, S. N.; Aswal, V. K.; Wagh, A. G.

    2008-01-01

    The structure of protein-surfactant complexes of two proteins bovine serum albumin (BSA) and lysozyme in presence of anionic surfactant sodium dodecyl sulfate (SDS) has been studied using small-angle neutron scattering (SANS). It is observed that these two proteins form different complex structures with the surfactant. While BSA protein undergoes unfolding on addition of surfactant, lysozyme does not show any unfolding even up to very high surfactant concentrations. The unfolding of BSA protein is caused by micelle-like aggregation of surfactant molecules in the complex. On the other hand, for lysozyme protein there is only binding of individual surfactant molecules to protein. Lysozyme in presence of higher surfactant concentrations has protein-surfactant complex structure coexisting with pure surfactant micelles

  3. ISOLATION OF EGG DROP SYNDROME VIRUS AND ITS MOLECULAR CHARACTERIZATION USING SODIUM DODECYL SULPHATE POLYACRYLAMIDE GEL ELECTROPHORESIS

    Directory of Open Access Journals (Sweden)

    M. H. Rasool, S. U. Rahman and M. K. Mansoor

    2005-10-01

    Full Text Available Six isolates of egg drop syndrome (EDS virus were recovered from five different outbreaks of EDS in commercial laying hens in and around Faisalabad. The aberrant eggs were fed to the susceptible laying hens for experimental induction of infection. The samples from infected birds (egg washing, cloacal swabs, oviducts and spleens were collected, processed and inoculated into 11-day old duck embryos. The presence of virus in harvested allanto-amniotic fluid was monitored by spot and microhaemagglutination tests and confirmed by haemagglutination inhibition and agar gel precipitation tests. The EDS virus grew well in duck embryos and agglutinated only avian but not mammalian red blood cells. These isolates were purified through velocity density gradient centrifugation. Protein concentration was determined through Lowry method and sodium dodecyl sulphate polyacrylamide gel electrophoresis (SDS-PAGE was conducted by loading 300 µg protein concentration on 12.5% gel using discontinuous buffer system. All the six isolates showed 13 polypeptides, which were identical to those described in the referral EDS-76 virus (strain-127. The molecular weights of the polypeptides ranged from 6.5 KDa to 126 KDa.

  4. Highly selective colorimetric detection of Ni2+ using silver nanoparticles cofunctionalized with adenosine monophosphate and sodium dodecyl sulfonate

    Science.gov (United States)

    Feng, Jiayu; Jin, Weiwei; Huang, Pengcheng; Wu, Fangying

    2017-09-01

    We report a dual-ligand strategy based on silver nanoparticles (AgNPs) for highly selective detection of Ni2+ using colorimetric techniques. Adenosine monophosphate (AMP) and sodium dodecyl sulfonate (SDS) were both used as ligands to modify AgNPs. The presence of Ni2+ induces the aggregation of AgNPs through cooperative electrostatic interaction and metal-ligand interaction, resulting in a color change from bright yellow to orange. The cofunctionalized AgNPs showed obvious advantages over the ones functionalized only by AMP or SDS in terms of selectivity. Under the optimized conditions, this sensing platform for Ni2+ works in the concentration range of 4.0 to 60 μM and has a low detection limit of 0.60 μM. In addition, the colorimetric assay is very fast, and the whole analysis can be completed within a few minutes. Thus, it can be directly used in tap water and lake water samples. [Figure not available: see fulltext.

  5. The influence of aqueous sodium dodecyl sulphate solution in the photoresponsivity of nitrogen doped graphene oxide photodetector

    Science.gov (United States)

    Ahmad, H.; Thandavan, T. M. K.

    2017-11-01

    The homogeneity and agglomeration in graphene based photodetector plays an important role in the photoconduction. The influence of sodium dodecyl sulphate (SDS) solution in nitrogen doped graphene oxide (N-GO) is studied based on the photoresponsivity behaviour. One step hydrothermal method and drop casting technique are utilized to obtain N-GO photodetectors. High photoresponsivity about 1000 folds is achieved in N-GO prepared with SDS solution (N-GO/SDS) compared to the N-GO prepared without SDS solution. Raman spectrum also revealed a high intense D and G band as well as a slightly broaden 2D band due to sp2 hybridization. The fabricated device has exhibited wide range of responsivity to infrared (IR) laser 974 nm pulse and illumination. Real time current measurement in N-GO and current-voltage (I-V) characteristics in N-GO/SDS showed a significant photoconduction due to laser 974 nm illumination. The external quantum efficiency (EQE) in the N-GO/SDS solution is about 394830% compared to N-GO prepared without SDS, which is only 272%. The evaluated fall time at frequency modulation of 0.1 and 1 Hz for direct current (dc) bias voltage of 5.0 V found to be shorter compared to that of 2.5 V, whereas the fall time at high frequency modulation at 5000 Hz exhibited similar time around 77 μs.

  6. Cytochrome P450 102A2 Catalyzes Efficient Oxidation of Sodium Dodecyl Sulphate: A Molecular Tool for Remediation

    Directory of Open Access Journals (Sweden)

    Irene Axarli

    2010-01-01

    Full Text Available Bacterial cytochrome P450s (CYPs constitute an important family of monooxygenase enzymes that carry out essential roles in the metabolism of endogenous compounds and foreign chemicals. In the present work we report the characterization of CYP102A2 from B. subtilis with a focus on its substrate specificity. CYP102A2 is more active in oxidation of sodium dodecyl sulphate (SDS than any other characterized CYP. The effect of SDS and NADPH concentration on reaction rate showed nonhyperbolic and hyperbolic dependence, respectively. The enzyme was found to exhibit a bell-shaped curve for plots of activity versus pH, over pH values 5.9–8.5. The rate of SDS oxidation reached the maximum value approximately at pH 7.2 and the pH transition observed controlled by two pas in the acidic (pa=6.7±0.08 and basic (pa=7.3±0.06 pH range. The results are discussed in relation to the future biotechnology applications of CYPs.

  7. Hexavalent Molybdenum Reduction to Mo-Blue by a Sodium-Dodecyl-Sulfate-Degrading Klebsiella oxytoca Strain DRY14

    Directory of Open Access Journals (Sweden)

    M. I. E. Halmi

    2013-01-01

    Full Text Available Bacteria with the ability to tolerate, remove, and/or degrade several xenobiotics simultaneously are urgently needed for remediation of polluted sites. A previously isolated bacterium with sodium dodecyl sulfate- (SDS- degrading capacity was found to be able to reduce molybdenum to the nontoxic molybdenum blue. The optimal pH, carbon source, molybdate concentration, and temperature supporting molybdate reduction were pH 7.0, glucose at 1.5% (w/v, between 25 and 30 mM, and 25°C, respectively. The optimum phosphate concentration for molybdate reduction was 5 mM. The Mo-blue produced exhibits an absorption spectrum with a maximum peak at 865 nm and a shoulder at 700 nm. None of the respiratory inhibitors tested showed any inhibition to the molybdenum-reducing activity suggesting that the electron transport system of this bacterium is not the site of molybdenum reduction. Chromium, cadmium, silver, copper, mercury, and lead caused approximately 77, 65, 77, 89, 80, and 80% inhibition of the molybdenum-reducing activity, respectively. Ferrous and stannous ions markedly increased the activity of molybdenum-reducing activity in this bacterium. The maximum tolerable concentration of SDS as a cocontaminant was 3 g/L. The characteristics of this bacterium make it a suitable candidate for molybdenum bioremediation of sites cocontaminated with detergent pollutant.

  8. Evidence of β-sheet structure induced kinetic stability of papain upon thermal and sodium dodecyl sulphate denaturation

    Directory of Open Access Journals (Sweden)

    Rašković Brankica

    2015-01-01

    Full Text Available Papain is a protease that consists of α-helical and β-sheet domains which unfold almost independently. Both, papain considerable thermal stability and sodium dodecyl sulphate (SDS resistance have been shown. However, the ability of each domain to unfold upon thermal and SDS denaturation has never been studied. This work shows that fruit papain has slightly higher thermal inactivation resistance when it is compared to stem papain with rather high activation energy (Ea of 223 ± 16 kJmol-1 and Tm50 value of 79 ± 2 °C. SDS resistance of fruit papain was estimated by SDS-PAGE analysis and activity staining. It has been noted that, in the presence of SDS, unless heat energy was applied in order to unfold papain, the protein remained active. Furthermore, it has been proven via Fourier transform infrared spectroscopy (FT-IR that α-helical domain of fruit papain is more prone to unfolding at elevated temperatures and in the presence of SDS then β-sheet rich domain. Thermal denaturation of papain without detergent present led to accelerated formation of aggregation specific intermolecular β-sheets as compared to native protein. Presented results are both, of fundamental and application importance. [Projekat Ministarstva nauke Republike Srbije, br. 172049

  9. Molecular mechanism of catalase activity change under sodium dodecyl sulfate-induced oxidative stress in the mouse primary hepatocytes.

    Science.gov (United States)

    Wang, Jing; Wang, Jiaxi; Xu, Chi; Liu, Rutao; Chen, Yadong

    2016-04-15

    Sodium dodecyl sulfate (SDS) contributes to adverse effects of organisms probably because of its ability to induce oxidative stress via changing the activity of antioxidant enzyme catalase (CAT). But the underlying molecular mechanisms still remain unclear. This study characterized the harmful effects of SDS-induced oxidative stress on the mouse primary hepatocytes as well as the structure and function of CAT molecule and investigated the underlying molecular mechanism. After 12h SDS (0.1μM to 0.2mM) exposure, no significant change was observed in CAT activity of the hepatocytes. After 0.5 and 0.8mM SDS exposure, the state of oxidative stress stimulated CAT production in the hepatocytes. The inhibition of CAT activity induced by directly interacting with SDS was unable to catch the synthesis of CAT and therefore resulted in the increased activity and elevated ROS level. Further molecular experiments showed that SDS prefers to bind to the interface with no direct effect on the active site and the structure of heme groups of CAT molecule. When the sites in the interface is saturated, SDS interacts with VAL 73, HIS 74, ASN 147 and PHE 152, the key residues of the enzyme activity, and leads to the decrease of CAT activity. Copyright © 2015 Elsevier B.V. All rights reserved.

  10. Removal of copper, nickel and zinc by sodium dodecyl sulphate coated magnetite nanoparticles from water and wastewater samples

    Directory of Open Access Journals (Sweden)

    Mahnaz Adeli

    2017-02-01

    Full Text Available In the present study, sodium dodecyl sulphate-coated Fe3O4 nanoparticles (SDS–Fe3O4 NPs were applied to remove Cu(II, Ni(II and Zn(II ions from water and wastewater samples. The effects of pH of solution, SDS, Fe3O4 NPs and salt addition on removal efficiency of the metal ions were investigated and optimized. Salt addition has a negative effect on the removal efficiency of the metal ions, thus extraction follows the ion exchange mechanism. The results showed that the adsorption process onto the adsorbent is very fast under optimum conditions and nearly 1 min of contact time was found to be sufficient for completion of the metal ions' adsorption. Adsorption equilibrium of the metal ions reveals that data were fitted well to the Langmuir isotherm. Also, the maximum monolayer capacity, qmax, obtained from the Langmuir isotherm was 24.3, 41.2 and 59.2 mg g−1 for Cu(II, Ni(II and Zn(II, respectively. Desorption experiments by elution of the adsorbent with methanol show that the SDS-Fe3O4 NPs could be reconditioned without significant loss of its initial properties even after three adsorption–desorption cycles. Finally, application of the SDS-Fe3O4 NPs as efficient adsorbent material for removal of the metal ions from Iran Khodro's wastewater samples was investigated and satisfactory results were obtained.

  11. Investigating the fate of activated sludge extracellular proteins in sludge digestion using sodium dodecyl sulfate polyacrylamide gel electrophoresis.

    Science.gov (United States)

    Park, Chul; Helm, Richard F; Novak, John T

    2008-12-01

    The fate of activated sludge extracellular proteins in sludge digestion was investigated using three different cation-associated extraction methods and sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE). Extraction methods used were the cation exchange resin (CER) method for extracting calcium (Ca2+) and magnesium (Mg2+), sulfide extraction for removing iron, and base treatment (pH 10.5) for dissolving aluminum. Extracellular polymeric substances extracted were then subjected to SDS-PAGE, and the resultant protein profiles were examined before and after sludge digestion. The SDS-PAGE results showed that three methods led to different SDS-PAGE profiles for both undigested and digested sludges. The results further revealed that CER-extracted proteins remained mainly undegraded in anaerobic digestion, but were degraded in aerobic digestion. While the fate of sulfide- and base-extracted proteins was not clear for aerobic digestion, their changes in anaerobic digestion were elucidated. Most sulfide-extracted proteins were removed by anaerobic digestion, while the increase in protein band intensity and diversity was observed for base-extracted proteins. These results suggest that activated sludge flocs contain different fractions of proteins that are distinguishable by their association with certain cations and that each fraction undergoes different fates in anaerobic and aerobic digestion. The proteins that were resistant to degradation and generated during anaerobic digestion were identified by liquid chromatography tandem mass spectrometry. Protein identification results and their putative roles in activated sludge and anaerobic digestion are discussed in this study.

  12. Sodium dodecyl sulfate/β-cyclodextrin vesicles embedded in chitosan gel for insulin delivery with pH-selective release

    Directory of Open Access Journals (Sweden)

    Zhuo Li

    2016-07-01

    Full Text Available In an answer to the challenge of enzymatic instability and low oral bioavailability of proteins/peptides, a new type of drug-delivery vesicle has been developed. The preparation, based on sodium dodecyl sulfate (SDS and β-cyclodextrin (β-CD embedded in chitosan gel, was used to successfully deliver the model drug-insulin. The self-assembled SDS/β-CD vesicles were prepared and characterized by particle size, zeta potential, appearance, microscopic morphology and entrapment efficiency. In addition, both the interaction of insulin with vesicles and the stability of insulin loaded in vesicles in the presence of pepsin were investigated. The vesicles were crosslinked into thermo-sensitive chitosan/β-glycerol phosphate solution for an in-situ gel to enhance the dilution stability. The in vitro release characteristics of insulin from gels in media at different pH values were investigated. The insulin loaded vesicles–chitosan hydrogel (IVG improved the dilution stability of the vesicles and provided pH-selective sustained release compared with insulin solution–chitosan hydrogel (ISG. In vitro, IVG exhibited slow release in acidic solution and relatively quick release in neutral solutions to provide drug efficacy. In simulated digestive fluid, IVG showed better sustained release and insulin protection properties compared with ISG. Thus IVG might improve the stability of insulin during its transport in vivo and contribute to the bioavailability and therapeutic effect of insulin.

  13. Fluorometric determination of proteins using the terbium (III)-2-thenoyltrifluoroacetone-sodium dodecyl benzene sulfonate-protein system

    Energy Technology Data Exchange (ETDEWEB)

    Jia Zhen [Key Laboratory of Colloid and Interface Chemistry of Education Ministry, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China); Department of Chemistry, Dezhou University, Dezhou 253023 (China); Yang Jinghe [Key Laboratory of Colloid and Interface Chemistry of Education Ministry, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China)]. E-mail: yjh@sdu.edu.cn; Wu Xia [Key Laboratory of Colloid and Interface Chemistry of Education Ministry, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China); Wang Fei [Key Laboratory of Colloid and Interface Chemistry of Education Ministry, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China); Guo Changying [Key Laboratory of Colloid and Interface Chemistry of Education Ministry, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China); Liu Shufang [Key Laboratory of Colloid and Interface Chemistry of Education Ministry, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China)

    2006-12-15

    It is found that in hexamethylene tetramine (HMTA)-HCl buffer of pH=8.00, proteins can enhance the fluorescence of terbium (III) (Tb{sup 3+})-2-thenoyltrifluoroacetone (TTA)-sodium dodecyl benzene sulfonate (SDBS) system. Based on this, a sensitive method for the determination of proteins is proposed. The experiments indicate that under the optimum conditions, the enhanced fluorescence intensity is in proportion to the concentration of proteins in the range of 4.0x10{sup -9}-7.5x10{sup -6}g/mL for bovine serum albumin (BSA), 5.0x10{sup -9}-1.5x10{sup -5}g/mL for human serum albumin (HSA), 1.0x10{sup -8}-7.5x10{sup -6}g/mL for egg albumin (EA). Their detection limits (S/N=3) are 0.5, 0.8 and 2.0ng/mL, respectively. The interaction mechanism is also studied.

  14. Preparation of Lignin/Sodium Dodecyl Sulfate Composite Nanoparticles and Their Application in Pickering Emulsion Template-Based Microencapsulation.

    Science.gov (United States)

    Pang, Yuxia; Wang, Shengwen; Qiu, Xueqing; Luo, Yanling; Lou, Hongming; Huang, Jinhao

    2017-12-20

    Lignin is a vastly underutilized biomass resource. The preparation of water-dispersed lignin nanoparticles is an effective way to realize the high-value utilization of lignin. However, the currently reported preparation methods of lignin nanoparticles still have some drawbacks, such as the requirement for toxic organic solvent or chemical modification, complicated operation process, and poor dispersibility. Here, lignin/sodium dodecyl sulfate (SDS) composite nanoparticles (LSNPs) with outstanding water dispersibility and a size range of 70-200 nm were facilely prepared via acidifying the mixed basic solution of alkaline lignin and SDS. No harsh chemical was needed. The formation mechanism was systematically studied. Results indicated that the LSNPs were obtained by acid precipitation of the mixed micelles formed by the self-assembly of lignin and SDS. In addition, on the basis of the LSNP-stabilized Pickering emulsions, lignin/polyurea composite microcapsules combining the excellent chemical stability of a synthetic polyurea shell with the fantastic antiphotolysis and antioxidant properties of lignin were successfully prepared.

  15. Effect of low concentration sodium dodecyl sulfate on the electromigration of palonosetron hydrochloride stereoisomers in micellar electrokinetic chromatography.

    Science.gov (United States)

    Hu, Shao-Qiang; Wang, Gui-Xia; Guo, Wen-Bo; Guo, Xu-Ming; Zhao, Min

    2014-05-16

    The effect of low concentrations of sodium dodecyl sulfate (SDS) on the separation of palonosetron hydrochloride (PALO) stereoisomers by micellar electrokinetic chromatography (MEKC) has been investigated. It was found that the addition of SDS prolongs the migration time and the migration order of four stereoisomers changes regularly with the SDS concentration. Good separations for all the four stereoisomers were achieved at appropriate SDS concentration. The effect of SDS on the electromigration (mobilities) of PALO stereoisomers has been studied, in order to explain its effect on the separation by MEKC. It was found that low concentrations of SDS added into the separation media forms negatively charged complexes with PALO stereoisomers and hence reverses their electromigration direction. Furthermore, the migration order between two enantiomeric pairs is also reversed because the enantiomeric pair with a bigger positive mobility than that of another pair turns to have a bigger negative mobility when bound with SDS. Based on these results, the effect of SDS on the MEKC separation of PALO stereoisomers was elucidated reasonably. The performance of the developed chiral MEKC method was validated by the analysis of a real sample. Copyright © 2014 Elsevier B.V. All rights reserved.

  16. Determination of antihypertensive drug moexipril hydrochloride based on the enhancement effect of sodium dodecyl sulfate at carbon paste electrode.

    Science.gov (United States)

    Attia, Ali K

    2010-04-15

    Herein, an electrochemical differential pulse voltammetric method was developed for the determination of moexipril hydrochloride based on the enhancement effect of sodium dodecyl sulfate. The oxidation process has been carried out in Britton-Robinson buffer. Moexipril hydrochloride exhibits a well-defined irreversible oxidation peak over the entire pH range (2-11). The peak current varied linearly over the range from 4.0 x 10(-7) to 5.2 x 10(-6) mol L(-1). The limits of detection and quantification were 6.87 x 10(-8) mol L(-1) and 2.29 x 10(-7) mol L(-1), respectively. The recovery was found in the range from 99.65% to 100.76%. The relative standard deviation was found in the range from 0.429% to 0.845%. The proposed method possesses high sensitivity, accuracy and rapid response. Finally, this method was successfully used to determine moexipril hydrochloride in tablets. (c) 2009 Elsevier B.V. All rights reserved.

  17. Inactivation of salmonella in biofilms and on chicken cages and preharvest poultry by levulinic Acid and sodium dodecyl sulfate.

    Science.gov (United States)

    Zhao, Tong; Zhao, Ping; Cannon, Jennifer L; Doyle, Michael P

    2011-12-01

    Surface contamination (skin and feathers) of broilers with Salmonella occurs primarily during growth and transportation. Immediately after transporting chickens, chicken cage doors were sprayed with a foam containing 3% levulinic acid plus 2% sodium dodecyl sulfate (SDS). Samples were collected for Salmonella assay after 45 min. Salmonella on cage doors was reduced from 19% (19 of 100 doors) before treatment to 1% (1 of 100 doors) after treatment, coliform counts were reduced from 6 to 8 to 2 to 4 log CFU/9 cm(2), and aerobic plate counts were reduced from 7 to 9 to 4 to 6 log CFU/9 cm(2). Whole chicken carcasses with feathers were inoculated with 10(8) CFU of Salmonella Enteritidis, soaked for 5 min at 21°C in 72 liters of a treatment or control solution, and assayed for Salmonella. Salmonella counts on chickens treated with water were 6.8 to 8.5 log CFU/9 cm(2), those treated with 50 ppm of calcium hypochlorite were 7.6 to 8.9 log CFU/9 cm(2), and those treated with 3% levulinic acid plus 2% SDS were 4-log reduction). Results of biofilm studies on surfaces of various materials revealed that a 3% levulinic acid plus 2% SDS treatment used as either a foam or liquid for 10 min effectively reduced Salmonella populations by 5 and >6 log CFU/cm(2), respectively.

  18. Effect of Surfactants on Plasmid DNA Stability and Release from ...

    African Journals Online (AJOL)

    Purpose: To evaluate the effect of surfactants on plasmid DNA during preparation and release from polylactic glycolide (PLGA) microspheres. Methods: Various surfactants, both ionic and non-ionic (Span, Tween, Triton X100, cetyltrimethylammonium bromide and sodium dodecyl sulphate), were added during the ...

  19. Photoisomerization of merocyanine 540 in polymer-surfactant ...

    Indian Academy of Sciences (India)

    Photoisomerization of merocyanine 540 (MC540) in a polymer-surfactant aggregate is studied using picosecond time resolved emission spectroscopy. The aggregate consists of the polymer, poly(vinylpyrrolidone) (PVP) and the surfactant, sodium dodecyl sulphate (SDS). With increase in the concentration of SDS in an ...

  20. Inactivation of heat adapted and chlorine adapted Listeria monocytogenes ATCC 7644 on tomatoes using sodium dodecyl sulphate, levulinic acid and sodium hypochlorite solution

    Directory of Open Access Journals (Sweden)

    Oluwatosin Ademola Ijabadeniyi

    2017-04-01

    Full Text Available The effectiveness of sodium dodecyl sulphate (SDS, sodium hypochlorite solution and levulinic acid in reducing the survival of heat adapted and chlorine adapted Listeria monocytogenes ATCC 7644 was evaluated. The results against heat adapted L. monocytognes revealed that sodium hypochlorite solution was the least effective, achieving log reduction of 2.75, 2.94 and 3.97 log colony forming unit (CFU/mL for 1, 3 and 5 minutes, respectively. SDS was able to achieve 8 log reduction for both heat adapted and chlorine adapted bacteria. When used against chlorine adapted L. monocytogenes sodium hypochlorite solution achieved log reduction of 2.76, 2.93 and 3.65 log CFU/mL for 1, 3 and 5 minutes, respectively. Using levulinic acid on heat adapted bacteria achieved log reduction of 3.07, 2.78 and 4.97 log CFU/mL for 1, 3, 5 minutes, respectively. On chlorine adapted bacteria levulinic acid achieved log reduction of 2.77, 3.07 and 5.21 log CFU/mL for 1, 3 and 5 minutes, respectively. Using a mixture of 0.05% SDS and 0.5% levulinic acid on heat adapted bacteria achieved log reduction of 3.13, 3.32 and 4.79 log CFU/mL for 1, 3 and 5 minutes while on chlorine adapted bacteria it achieved 3.20, 3.33 and 5.66 log CFU/mL, respectively. Increasing contact time also increased log reduction for both test pathogens. A storage period of up to 72 hours resulted in progressive log reduction for both test pathogens. Results also revealed that there was a significant difference (P≤0.05 among contact times, storage times and sanitizers. Findings from this study can be used to select suitable sanitizers and contact times for heat and chlorine adapted L. monocytogenes in the fresh produce industry.

  1. Inactivation of Heat Adapted and Chlorine AdaptedListeria MonocytogenesATCC 7644 on Tomatoes Using Sodium Dodecyl Sulphate, Levulinic Acid and Sodium Hypochlorite Solution.

    Science.gov (United States)

    Ijabadeniyi, Oluwatosin Ademola; Mnyandu, Elizabeth

    2017-04-13

    The effectiveness of sodium dodecyl sulphate (SDS), sodium hypochlorite solution and levulinic acid in reducing the survival of heat adapted and chlorine adapted Listeria monocytogenes ATCC 7644 was evaluated. The results against heat adapted L. monocytognes revealed that sodium hypochlorite solution was the least effective, achieving log reduction of 2.75, 2.94 and 3.97 log colony forming unit (CFU)/mL for 1, 3 and 5 minutes, respectively. SDS was able to achieve 8 log reduction for both heat adapted and chlorine adapted bacteria. When used against chlorine adapted L. monocytogenes sodium hypochlorite solution achieved log reduction of 2.76, 2.93 and 3.65 log CFU/mL for 1, 3 and 5 minutes, respectively. Using levulinic acid on heat adapted bacteria achieved log reduction of 3.07, 2.78 and 4.97 log CFU/mL for 1, 3, 5 minutes, respectively. On chlorine adapted bacteria levulinic acid achieved log reduction of 2.77, 3.07 and 5.21 log CFU/mL for 1, 3 and 5 minutes, respectively. Using a mixture of 0.05% SDS and 0.5% levulinic acid on heat adapted bacteria achieved log reduction of 3.13, 3.32 and 4.79 log CFU/mL for 1, 3 and 5 minutes while on chlorine adapted bacteria it achieved 3.20, 3.33 and 5.66 log CFU/mL, respectively. Increasing contact time also increased log reduction for both test pathogens. A storage period of up to 72 hours resulted in progressive log reduction for both test pathogens. Results also revealed that there was a significant difference (P≤0.05) among contact times, storage times and sanitizers. Findings from this study can be used to select suitable sanitizers and contact times for heat and chlorine adapted L. monocytogenes in the fresh produce industry.

  2. Oral Decontamination of Orthodontic Patients Using Photodynamic Therapy Mediated by Blue-Light Irradiation and Curcumin Associated with Sodium Dodecyl Sulfate.

    Science.gov (United States)

    Panhóca, Vitor Hugo; Esteban Florez, Fernando Luis; Corrêa, Thaila Quatrini; Paolillo, Fernanda Rossi; de Souza, Clovis Wesley Oliveira; Bagnato, Vanderlei Salvador

    2016-09-01

    The aim of this study was to investigate the effects of the antimicrobial photodynamic therapy (aPDT) using the association of curcumin with the surfactant sodium dodecyl sulfate (SDS) for oral decontamination in orthodontic patients. The installation of the orthodontic appliances promotes an increase in the retentive area that is available for microbial aggregation and makes difficult the oral health promotion. However, aPDT is one possible approach that is used for the reduction of oral microbial load. Twenty-four patients (n = 24) were randomly distributed into four groups: Light group: which was treated only with the blue light, no drug; PDT group, which was treated with curcumin and blue light; PDT + S group, which was treated with curcumin plus surfactant and irradiated with blue light; and Chlorhex group, which was treated with chlorhexidine. The photosensitizer agent was prepared by adding 0.1% of SDS to a curcumin solution of 1 g/L. Two distinct LED devices emitting blue light (450 ± 10 nm) were used as follows: extra-oral irradiation (200 mW, 80 mW/cm(2), 36 J and 14 J/cm(2)) and intra-oral irradiation (1200 mW, 472 mW/cm(2), 216 J and 85 J/cm(2)).The collection of nonstimulated saliva (n = 3; 3 mL/collection) was performed at the following steps: (1) immediately before swishing (curcumin, chlorhexidine, or water); (2) after swishing; and (3) after performing aPDT treatments. The colony-forming units (CFU) were counted visually, and the values were adjusted to CFU/mL. There was significant Log reduction for PDT (from 6.33 ± 0.92 to 5.78 ± 0.96, p < 0.05), PDT + S (from 5.44 ± 0.94 to 3.83 ± 0.71, p < 0.01), and Chlorhex (from 5.89 ± 0.97 to 2.55 ± 1.80, p < 0.01) groups. The survival rate was significantly reduced in both PDT + S and Chlorhex groups compared with all situations (p < 0.05). However, there was no significant difference between PDT + S and

  3. Determination of Protein by Fluorescence Enhancement of Curcumin in Lanthanum-Curcumin-Sodium Dodecyl Benzene Sulfonate-Protein System

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Feng [Zaozhuang University, People' s Republic of China; Huang, Wei [Zaozhuang University, People' s Republic of China; Zhang, Yunfeng [Zaozhuang University, People' s Republic of China; Wang, Mingyin [Zaozhuang University, People' s Republic of China; Sun, Lina [Zaozhuang University, People' s Republic of China; Tang, Bo [Shandong University, Jinan, China; Wang, Wei [ORNL

    2011-01-01

    We found that the fluorescence intensity of the lanthanum (La(3+))-curcumin (CU) complex can be highly enhanced by proteins in the presence of sodium dodecyl benzene sulphonate (SDBS). Based on this finding, a new fluorimetric method for the determination of protein was developed. Under optimized conditions, the enhanced intensities of fluorescence are quantitatively in proportion to the concentrations of proteins in the range 0.0080-20.0 g mL(-1) for bovine serum albumin (BSA) and 0.00080-20.0 g mL(-1) for human serum albumin (HSA) with excitation of 425 nm, and 0.00020-20.0 g mL(-1) for bovine serum albumin (BSA) and 0.00080-20.0 g mL(-1)for human serum albumin (HSA) with excitation of 280 nm, while corresponding qualitative detection limits (S/N 3) are as low as 5.368, 0.573, 0.049, 0.562 g mL(-1), respectively. Study on reaction mechanism reveals that proteins can bind with La(3+), CU and SDBS through self-assembling function with electrostatic attraction, hydrogen bonding, hydrophobic interaction and van der Waals forces, etc. The proteins form a supermolecular association with multilayer structure, in which La(3+)-CU is clamped between BSA and SDBS. The unique high fluorescence enhancement of CU is resulted through synergic effects of favorable hydrophobic microenvironment provided by BSA and SDBS, and efficient intermolecular energy transfer among BSA, SDBS and CU. In energy transfer process, La(3+) plays a crucial role because it not only shortens the distance between SDBS and CU, but also acts as a "bridge" for transferring the energy from BSA to CU.

  4. Efficacy of a levulinic acid plus sodium dodecyl sulfate-based sanitizer on inactivation of human norovirus surrogates.

    Science.gov (United States)

    Cannon, Jennifer L; Aydin, Ali; Mann, Amy N; Bolton, Stephanie L; Zhao, Tong; Doyle, Michael P

    2012-08-01

    Human noroviruses are the most common etiologic agent of foodborne illness in the United States. The inability to culture human noroviruses in the laboratory necessitates the use of surrogate viruses such as murine norovirus (MNV-1) and feline calicivirus (FCV) for inactivation studies. In this study, a novel sanitizer of organic acid (levulinic acid) plus the anionic detergent sodium dodecyl sulfate (SDS) was evaluated. Viruses were treated with levulinic acid (0.5 to 5%), SDS (0.05 to 2%), or combinations of levulinic acid plus SDS (1:10 solution of virus to sanitizer). MNV-1 inoculated onto stainless steel also was treated with a 5% levulinic acid plus 2% SDS liquid or foaming solution. Log reductions of viruses were determined with a plaque assay. Neither levulinic acid nor SDS alone were capable of inactivating MNV-1 or FCV, resulting in a ≤0.51-log reduction of the infectious virus titer. However, the combination of 0.5% levulinic acid plus 0.5% SDS inactivated both surrogates by 3 to 4.21 log PFU/ml after 1 min of exposure. Similarly, MNV-1 inoculated onto stainless steel was reduced by >1.50 log PFU/ml after 1 min and by >3.3 log PFU/ml after 5 min of exposure to a liquid or foaming solution of 5% levulinic acid plus 2% SDS. The presence of organic matter (up to 10%) in the virus inoculum did not significantly affect sanitizer efficacy. The fact that both of the active sanitizer ingredients are generally recognized as safe to use as food additives by the U.S. Food and Drug Administration further extends its potential in mitigating foodborne disease.

  5. Evaluation of levulinic acid and sodium dodecyl sulfate as a sanitizer for use in processing Georgia-grown cantaloupes.

    Science.gov (United States)

    Webb, Cathy C; Davey, Lindsey E; Erickson, Marilyn C; Doyle, Michael P

    2013-10-01

    Freshly harvested Georgia-grown cantaloupes (Cucumis melo L. var. reticulatus cv. Athena and Atlantis) were spot inoculated with 100 μl of a five-strain mixture of Salmonella enterica serovar Poona (9 log CFU/ml) at the stem scar and on the netted rind and then subjected to no treatment (control) or a 6-min treatment (tank only) in water, 120 ppm of chlorine (pH 7.0), 1% levulinic acid plus 0.1% sodium dodecyl sulfate (SDS; pH 3.0), or 2% levulinic acid plus 0.2% SDS (pH 3.0). The log reduction for the tank-only treatments was 0.31, 0.59, 1.32, and 1.37 log CFU/g at the stem scar and 0.97, 1.59, 2.06. and 3.37 log CFU/g on the netted rind for water, chlorine, 1% levulinic acid plus 0.1% SDS, and 2% levulinic acid plus 0.2% SDS, respectively. A greater log reduction was observed for the cantaloupe surface tissue with the water, chlorine, and 2% levulinic acid plus 0.2% SDS treatments when additional sanitizer (2 ml) and brushing (to simulate cantaloupes tumbling over brushes on the processing line) were added to the dump tank treatment. The stem scar tissue reductions were 0.90, 1.69, and 1.53 log CFU/g, whereas the netted rind reductions were 1.56, 2.50, and 4.47 log CFU/g after treatment with water, chlorine, and 2% levulinic acid plus 0.2% SDS, respectively. These data suggest that 2% levulinic acid plus 0.2% SDS is effective for reducing Salmonella on the netted rind surface of cantaloupes. However, neither 2% levulinic acid plus 0.2% SDS nor 120 ppm of chlorine substantially reduced Salmonella on stem scar tissue.

  6. Efficacy of levulinic acid-sodium dodecyl sulfate against Encephalitozoon intestinalis, Escherichia coli O157:H7, and Cryptosporidium parvum.

    Science.gov (United States)

    Ortega, Ynes R; Torres, Maria P; Tatum, Jessica M

    2011-01-01

    Foodborne parasites are characterized as being highly resistant to sanitizers used by the food industry. In 2009, a study reported the effectiveness of levulinic acid in combination with sodium dodecyl sulfate (SDS) in killing foodborne bacteria. Because of their innocuous properties, we studied the effects of levulinic acid and SDS at various concentrations appropriate for use in foods, on the viability of Cryptosporidium parvum and Encephalitozoon intestinalis. The viability of Cryptosporidium and E. intestinalis was determined by in vitro cultivation using the HCT-8 and RK-13 cell lines, respectively. Two Escherichia coli O157:H7 isolates were also used in the present study: strain 932 (a human isolate from a 1992 Oregon meat outbreak) and strain E 0018 (isolated from calf feces). Different concentrations and combinations of levulinic acid and SDS were tested for their ability to reduce infectivity of C. parvum oocysts (10(5)), E. intestinalis spores (10(6)), and E. coli O157:H7 (10(7)/ml) when in suspension. Microsporidian spores were treated for 30 and 60 min at 20 ± 2°C. None of the combinations of levulinic acid and SDS were effective at inactivating the spores or oocysts. When Cryptosporidium oocysts were treated with higher concentrations (3% levulinic acid-2% SDS and 2% levulinic acid-1% SDS) for 30, 60, and 120 min, viability was unaffected. E. coli O157:H7, used as a control, was highly sensitive to the various concentrations and exposure times tested. SDS and levulinic acid alone had very limited effect on E. coli O157:H7 viability, but in combination they were highly effective at 30 and 60 min of incubation. In conclusion, Cryptosporidium and microsporidia are not inactivated when treated for various periods of time with 2% levulinic acid-1% SDS or 3% levulinic acid-2% SDS at 20°C, suggesting that this novel sanitizer cannot be used to eliminate parasitic contaminants in foods.

  7. Aplikasi Metode SDS-PAGE (Sodium Dodecyl Sulphate Poly Acrylamide Gel Electrophoresis untuk Mengidentifikasi Sumber Asal Gelatin pada Kapsul Keras

    Directory of Open Access Journals (Sweden)

    Sandra Hermanto

    2016-08-01

    Full Text Available Gelatin as the main ingredient of capsules is still a problem for a moslem. Most of gelatin production remains largely derived from non-halal materials. One of gelatin source is came from collagen of the skin and bones of bovine or pork. The main of study is determine the source of gelatin used in hard capsules by using SDS-PAGE (Sodium Dodecyl Sulphate Gel electrophoresis Poly Acrylamide method. In the early stages, optimization of standards bovine and pork gelatin were hydrolyzed by pepsin at pH 4.5 and 60°C for 1 hour, 2 hours, and 3 hours. Gelatin hydrolyzateswere analyzed by SDS-PAGE to determine the optimal hydrolysis time. Identification of gelatin hydrolyzate fragments were carried by molecular weight. Hydrolysis time optimization throught applied to identify the source of hard gelatin capsules in the samples obtained from market and compared with the simulation of hard gelatin capsules. The results showed there were of specific bands of bovine gelatin with a molecular weight of 11,4 kDa; 34 kDa; 47kDa and specific bands of pork gelatin with a molecular weight of 24.7 kDa; 28 kDa; and 60 kDa. Similar results were obtained on a sample of hard capsules with bands of protein fragments that were identical to bovine gelatinstandard. Based on the results,each of the samples were tested contain of bovine gelatin respectively. DOI :http://dx.doi.org/10.15408/jkv.v0i0.3150

  8. Antigenic profile of heat-killed versus thimerosal-treated Leishmania major using sodium dodecyl sulfate-polyacrylamide gel electrophoresis

    Directory of Open Access Journals (Sweden)

    Reza Arjmand

    2015-01-01

    Full Text Available Background: Leishmania is a parasitic protozoan of trypanosomatidae family which causes a wide spectrum of diseases ranging from self-healing cutaneous lesions to deadly visceral forms. In endemic areas, field trials of different preparations of Leishmania total antigen were tested as leishmaniasis vaccine. Two preparations of killed Leishmania major were produced In Iran, which were heat-killed vaccine called autoclaved L. major (ALM and thimerosal-treated freeze-thawed vaccine called killed L. major (KLM. In this study, the protein content of both ALM and KLM were compared with that of freshly harvested intact L. major promastigotes using sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE. Materials and Methods: L. major (MRHO/IR/75/ER from pre-infected Balb/c mice was isolated with modified Novy-MacNeal-Nicolle (NNN medium and then subcultured in liquid RPMI 1640 medium supplemented with fetal calf serum (FCS 20% for mass production. Two preparations of KLM and ALM were produced by Razi Vaccine and Serum Research Institute, Iran, under WHO/TDR supervision. Electrophoresis was performed by SDS-PAGE method and the gel was stained by Coomassie brilliant blue dye. The resultant unit bands were compared using standard molecular proteins. Results: Electrophoresis of the two preparations produced many bands from 10 kDa to 100 kDa. KLM bands were much like those of freshly harvested intact L. major. Conclusion: It is concluded that although there are similar bands in the three forms of Leishmania antigens, there are some variations which might be considered for identification and purification of protective immunogens in a total crude antigen, and detection of their stability is essential for the production and marketing of a putative vaccine.

  9. Study of adjuvant effect of model surfactants from the groups of alkyl sulfates, alkylbenzene sulfonates, alcohol ethoxylates and soaps

    DEFF Research Database (Denmark)

    Clausen, S K; Sobhani, S; Poulsen, O M

    2000-01-01

    The sodium salts of representatives of anionic surfactants, dodecylbenzene sulfonate (SDBS), dodecyl sulfate (SDS) and coconut oil fatty acids, and a nonionic surfactant, dodecyl alcohol ethoxylate, were studied for adjuvant effect on the production of specific IgE antibodies in mice. The surfact......The sodium salts of representatives of anionic surfactants, dodecylbenzene sulfonate (SDBS), dodecyl sulfate (SDS) and coconut oil fatty acids, and a nonionic surfactant, dodecyl alcohol ethoxylate, were studied for adjuvant effect on the production of specific IgE antibodies in mice...... showed a statistically significant increase in OVA specific IgE levels. After two boosters, a statistically significant suppression in OVA-specific IgE production occurred with SDS (1000 mg/l), SDBS (1000 and 100 mg/l), coconut soap (1000 mg/l) and the alcohol ethoxylate (10 mg/l). This study suggests...

  10. Binding of alkylpyridinium chloride surfactants to sodium polystyrene sulfonate

    NARCIS (Netherlands)

    Ishiguro, M.; Koopal, L.K.

    2009-01-01

    Binding of cationic surfactants to anionic polymers is well studied. However, the surfactant binding characteristics at very low concentration near the start of binding and at high concentration, where charge compensation may Occur. are less well known. Therefore, the binding characteristics of

  11. Effects of multi-walled carbon nanotubes on mineralization and mobility of nonylphenol and sodium dodecyl sulfate in agricultural soils

    Science.gov (United States)

    Lillotte, Julia; Marschner, Bernd; Stumpe, Britta

    2014-05-01

    Nanotechnology is one of the major scientific research fields in this decade. One of the most wide-spread nanomaterials are carbon based nanoparticles (CNPs) which are increasingly be used in industry. Several studies shows that CNPs are interacting with other chemical compounds and organic pollutants in the environment. It is assumed that the interactions between CNPs and organic pollutants are affected by solution and aggregate behavior. Based on the knowledge of the behavior of CNPs and organic pollutants in aquatic systems the interactions of CNPs and organic pollutants in agricultural soils have to be studied. As organic pollutants two environmental substances, nonylphenol (NP) and sodium dodecyl sulfate (SDS) were selected as model substances. They occur frequently in aqueous systems and also show different solubility behavior. As CNP representatives, two different multi-walled carbon nanotubes (MWNT) were selected. They differed either in length or outer diameter. Conclusions therefrom are to be closed the influence of length and diameter of the sorption capacity of different organic pollutants. In addition, two agricultural soils (sandy and silty soil) and one forest soil (sandy soil) were chosen. Mineralization and sorption experiments were conducted to provide information about the degradation of organic pollutants in presence of multi-walled carbon nanotubes in soils. To analyze the CNPs mineralization potential, peroxidase activity was measured. Further extraction experiments were conducted to detect the extractable part of organic pollutants. The results show that the surface area of the MWNT has a significant impact on the sorption behav-ior of NP and SDS in soils. The sorption of NP and SDS is much higher than without MWNT. However, the properties of the organic pollutants (different water solubility and hydrophobicity) are equally important and should be noted. The degradation of both pollutants is influenced by MWNT. Due to the strong sorption of

  12. Effect of surfactant on porosity and swelling behaviors of guar gum-g-poly(sodium acrylate-co-styrene)/attapulgite superabsorbent hydrogels.

    Science.gov (United States)

    Shi, Xiao-Ning; Wang, Wen-Bo; Wang, Ai-Qin

    2011-11-01

    Novel fast-swelling porous guar gum-g-poly(sodium acrylate-co-styrene)/attapulgite (GG-g-P(NaA-co-St)/APT) superabsorbent hydrogels were prepared by simultaneous free-radical graft copolymerization reaction of guar gum (GG), partially neutralized AA (NaA), styrene (St) and attapulgite (APT) using N,N'-methylenebisacrylamide (MBA) as a crosslinker and ammonium persulfate (APS) as an initiator in aqueous solution and the surfactant self-assembling templating pore-forming technique. Fourier transform infrared (FTIR) spectroscopy confirmed that the surfactant could be removed from the final hydrogel product by methanol/water (8:1, v/v) washing process and the surfactant only act as micelle template to form pores. The effect of surfactant type on the porous microstructure of the hydrogel was assessed by field emission scanning electron microscope (FESEM). It was shown that incorporation of proper amount of anionic surfactant sodium n-dodecyl sulfate (SDS) in the gelling process of the hydrogel can obviously enhance the swelling capacity and initial swelling rate. The salt-sensitivity of the SDS-added hydrogel in distilled water and 15 mmol/L NaCl, CaCl(2) solution or 15 mmol/L NaCl and CaCl(2) solution was investigated, and it was found that the swelling-deswelling capability is quite reversible. A similar reproducible on-off switching behavior was observed in the 1 mmol/L solution of phosphate buffer at pH 2.1 and 7.4. Copyright © 2011 Elsevier B.V. All rights reserved.

  13. Fungal growth on anion surfactant medium.

    Science.gov (United States)

    Hamada, Nobuo; Abe, Niichiro

    2009-12-01

    Before the present study, no fungi using anion surfactant as a nutrient had been identified, although some fungi were known to use nonion surfactant. Washing water collected from 63 washing machines was inoculated onto 0.1% LAS (Sodium dodecyl benzenesulfonate) anion surfactant media to identify fungi that can feed on anion-surfactant. Small dark colonies of fungi were found on several of the Petri-dishes from 12 days after inoculation. These were identified as Cladophialophora boppii and Exophiala spinifera using morphological features and rDNA data. A number of the isolates of C. boppii specifically were recognized as using anion surfactant as a nutrient. The growth characteristics of the two fungal species were examined on surfactant media of three kinds. Apart from anion surfactant, the fungi were also able to grow on nonion surfactant and on soap. The application of these fungi for environmental cleansing after detergent pollution is also discussed.

  14. Analysis of Soluble Proteins in NaturalCordyceps sinensisfrom Different Producing Areas by Sodium Dodecyl Sulfate-Polyacrylamide Gel Electrophoresis and Two-dimensional Electrophoresis.

    Science.gov (United States)

    Li, Chun-Hong; Zuo, Hua-Li; Zhang, Qian; Wang, Feng-Qin; Hu, Yuan-Jia; Qian, Zheng-Ming; Li, Wen-Jia; Xia, Zhi-Ning; Yang, Feng-Qing

    2017-01-01

    As one of the bioactive components in Cordyceps sinensis (CS), proteins were rarely used as index components to study the correlation between the protein components and producing areas of natural CS. Protein components of 26 natural CS samples produced in Qinghai, Tibet, and Sichuan provinces were analyzed and compared to investigate the relationship among 26 different producing areas. Proteins from 26 different producing areas were extracted by Tris-HCl buffer with Triton X-100, and separated using sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) and two-dimensional electrophoresis (2-DE). The SDS-PAGE results indicated that the number of protein bands and optical density curves of proteins in 26 CS samples was a bit different. However, the 2-DE results showed that the numbers and abundance of protein spots in protein profiles of 26 samples were obviously different and showed certain association with producing areas. Based on the expression values of matched protein spots, 26 batches of CS samples can be divided into two main categories (Tibet and Qinghai) by hierarchical cluster analysis. The number of protein bands and optical density curves of proteins in 26 Cordyceps sinensis samples were a bit different on the sodium dodecyl sulfate-polyacrylamide gel electrophoresis protein profilesNumbers and abundance of protein spots in protein profiles of 26 samples were obvious different on two-dimensional electrophoresis mapsTwenty-six different producing areas of natural Cordyceps sinensis samples were divided into two main categories (Tibet and Qinghai) by Hierarchical cluster analysis based on the values of matched protein spots. Abbreviations Used : SDS-PAGE: Sodium dodecyl sulfate polyacrylamide gel electrophoresis, 2-DE: Two-dimensional electrophoresis, Cordyceps sinensis : CS, TCMs: Traditional Chinese medicines.

  15. Enhanced removal of detergent and recovery of enzymatic activity following sodium dodecyl sulfate-polyacrylamide gel electrophoresis: UUse of casein in gel wash buffer

    International Nuclear Information System (INIS)

    McGrew, B.R.; Green, D.M.

    1990-01-01

    The inclusion of 1% casein or bovine serum albumin in buffer used to reactivate enzymes subjected to sodium dodecyl sulfate (SDS)-polyacrylamide electrophoresis resulted in accelerated removal of SDS and restoration of nuclease and beta-galactosidase enzyme activities. Nuclease and beta-galactosidase activities which are absent from gels after longer wash procedures are detectable with this technique. Enzyme activity in gels prepared with SDS which contained inhibitory contaminants was partially restored by the casein wash procedure. The threshold of detection of two-dimensionally separated deoxyribonuclease I using the casein wash procedure was 1 picogram

  16. Interactions between a poorly soluble cationic drug and sodium dodecyl sulfate in dissolution medium and their impact on in vitro dissolution behavior.

    Science.gov (United States)

    Huang, Zongyun; Parikh, Shuchi; Fish, William P

    2018-01-15

    In the pharmaceutical industry, in vitro dissolution testing ofsolid oral dosage forms is a very important tool for drug development and quality control. However, ion-pairing interaction between the ionic drugand surfactants in dissolution medium often occurs, resulting in inconsistent and incomplete drug release. The aim of this study is toevaluate the effects ofsodium dodecyl sulfate (SDS) mediated medium onthe dissolution behaviors of a poorly soluble cationic drug (Drug B). The study was carried out by measuring solubility of Drug B substance and dissolution rate of Drug B product in media containing SDS.Desolubilization of Drug B substance was observed at pH 4.5 in the presence of SDS at concentrations below critical micelle concentration (CMC) which is attributed to the formation of an insoluble di-dodecyl sulfate salt between SDS and Drug B. This ion-pairing effect is less significant with increasing medium pH where Drug B is less ionized and CMC of SDS is lower. In medium at pH 4.5, dissolution of Drug B product was found incomplete with SDS concentration below CMC due to the desolubilization of Drug B substance. In media with SDS level above CMC, the dissolution rate is rather slower with higher inter-vessel variations compared to that obtained in pH 4.5 medium without SDS. The dissolution results demonstrate that the presence of SDS in medium generates unexpected irregular dissolution profiles for Drug B which are attributed to incompatible dissolution medium for this particular drug. Therefore, non-ionic surfactant was selected for Drug B product dissolution method and ion-pairing effect in SDS mediated medium should be evaluated when developing a dissolution method for any poorly soluble cationic drugs. Copyright © 2017 Elsevier B.V. All rights reserved.

  17. Dynamics of adsorption of polyallylamine hydrochloride/sodium dodecyl sulphate at water/air and water/hexane interfaces

    Czech Academy of Sciences Publication Activity Database

    Sharipova, A.; Aidarova, S.; Fainerman, V. B.; Stocco, A.; Černoch, Peter; Miller, R.

    2011-01-01

    Roč. 391, 1-3 (2011), s. 112-118 ISSN 0927-7757. [International Symposium on Surfactants in Solution /18./ - SIS 2010. Melbourne, 14.11.2010-19.11.2010] Institutional research plan: CEZ:AV0Z40500505 Keywords : mixed adsorption layers * polymer/surfactant mixtures * water/oil interface Subject RIV: CD - Macromolecular Chemistry Impact factor: 2.236, year: 2011

  18. Rheologycal properties of sodium carboxymethylcellulose in the presence of electrolyte and mixed micelle of surfactants

    Directory of Open Access Journals (Sweden)

    Sovilj Verica J.

    2003-01-01

    Full Text Available One of the most significant aspects of polymer-surfactant interaction, from the practical point of view, is that of rheology control and viscosity enhancement. In the oppositely charged polyelectrolyte-surfactant system strong ionic interaction often leads to precipitation of the formed complex yielding serious problems. In this paper the interaction between anionic polyelectrolyte - sodium carboxymethylcellulose (NaCMC and cationic surfactant - cethyltrimethylammonium bromide (CTMAB has been investigated by rheological measurements. Addition of electrolyte NaBr and nonionic surfactant - Tween 80 reduced the binding strength, prevented the precipitation of the complex and increased the viscosity of the system. It was found that rheological properties are strong influenced by NaCMC-CTMAB interaction and the system exhibits either pseudoplastic or thixotropic or rheopectic behavior according to the intensity of interaction.

  19. Preparation of Organized Mesoporous Silica from Sodium Metasilicate Solutions in Alkaline Medium using Nonionic Surfactants

    Czech Academy of Sciences Publication Activity Database

    Zukalová, Markéta; Rathouský, Jiří; Zukal, Arnošt

    2003-01-01

    Roč. 68, č. 10 (2003), s. 2019-2031 ISSN 0010-0765 Institutional research plan: CEZ:AV0Z4040901 Keywords : mesoporous SiO2 * sodium metasilicate * nonionic surfactants Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 1.041, year: 2003

  20. Polycation-Sodium Lauryl Ether Sulfate-Type Surfactant Complexes : Influence of Ethylene Oxide Length

    NARCIS (Netherlands)

    Vleugels, Leo F. W.; Pollet, Jennifer; Tuinier, Remco

    2015-01-01

    Poiyelectrolyte-surfactant complexes (PESC) are a class of materials which form spontaneously by self-assembly driven by electrostatic and hydrophobic interactions. PESC containing sodium lauryl ether Sulfates (SLES) have found wide application in hair care products like shampoo. Typically, SLES

  1. DETERMINATION OF SURFACTANT SODIUM LAURYL ETHER SULFATE BY ION PAIRING CHROMATOGRAPHY WITH SUPPRESSED CONDUCTIVITY DETECTION

    Science.gov (United States)

    A method for the determination of the anionic Steol CS-330 surfactant is described. CS-330 is a complex mixture of oligomers due to the various sizes of fatty alcohols and the number of moles of the ethoxylation. The main component of CS-330 is sodium lauryl ether sulfate (SLES)....

  2. Effects of buffered vinegar and sodium dodecyl sulfate plus levulinic acid on Salmonella Typhimurium survival, shelf-life, and sensory characteristics of ground beef patties.

    Science.gov (United States)

    Stelzleni, Alexander M; Ponrajan, Amudhan; Harrison, Mark A

    2013-09-01

    The inclusion of two sources of buffered vinegar and sodium dodecyl sulfate plus levulinic acid were studied as interventions for Salmonella Typhimurium and for their effect on shelf-life and sensory characteristics of ground beef. For the Salmonella challenge, beef trimmings (80/20) were inoculated then treated with 2% (w/v) liquid buffered vinegar (LVIN), 2.5% (w/w) powdered buffered vinegar (PVIN), a solution containing 1.0% levulinic acid plus 0.1% sodium dodecyl sulfate (SDLA) at 10% (w/v), or had no intervention applied (CNT). The same trim source and production methods were followed during production of patties for shelf-life and sensory testing without inoculation. SDLA patties had the largest reduction (P<0.05; 0.70 log CFU/g) of Salmonella. However, LVIN and PVIN had the least (P<0.05) psychrotrophic growth. SDLA patties had more purge (P<0.05) and lower (P<0.05) subjective color scores. There were not large differences in sensory characteristics, except PVIN exhibited stronger off-flavor (P<0.05). Copyright © 2013 Elsevier Ltd. All rights reserved.

  3. The corrosion properties of phosphate coating on AZ31 magnesium alloy: The effect of sodium dodecyl sulfate (SDS) as an eco-friendly accelerating agent

    Energy Technology Data Exchange (ETDEWEB)

    Amini, R. [Department of Polymer Engineering and Color Technology, AmirKabir University of Technology, P.O. Box 15875-4413, Tehran (Iran, Islamic Republic of); Sarabi, A.A., E-mail: sarabi@aut.ac.ir [Department of Polymer Engineering and Color Technology, AmirKabir University of Technology, P.O. Box 15875-4413, Tehran (Iran, Islamic Republic of)

    2011-06-01

    Sodium nitrite has been used as an accelerating agent in phosphating bath to improve its properties. However, it is well known that sodium nitrite is a carcinogenic component in phosphating sludge. In this study, it has been aimed to replace sodium nitrite by an environmentally friendly accelerating agent. To this end, sodium dodecyl sulfate (SDS) was used in phosphating bath to improve the phosphate coating formation on an AZ31 magnesium alloy. The effect of SDS/sodium nitrite ratio on the phosphated samples properties was also studied. Using field emission scanning electron microscope (FE-SEM), X-ray diffraction (XRD), direct current (DC) polarization and electrochemical impedance spectroscopy (EIS) the properties of phosphated magnesium samples were studied. Results showed uniform phosphate coating formation on the magnesium sample mostly in hopeite phase composition. In addition, a denser and less permeable coating can be obtained at these conditions. The corrosion resistance of the phosphated samples was superiorly improved using higher SDS concentration in the phosphating bath.

  4. Interactions between Surfactants in Solution and Electrospun Protein Fibers: Effects on Release Behavior and Fiber Properties

    DEFF Research Database (Denmark)

    Boutrup Stephansen, Karen; García-Díaz, María; Jessen, Flemming

    2016-01-01

    , and drug delivery. In the present study, we present a systematic investigation of how surfactants and proteins, as physiologically relevant components, interact with insulin-loaded fish sarcoplasmic protein (FSP) electrospun fibers (FSP-Ins fibers) in solution and thereby affect fiber properties...... such as accessible surface hydrophilicity, physical stability, and release characteristics of an encapsulated drug. Interactions between insulin-loaded protein fibers and five anionic surfactants (sodium taurocholate, sodium taurodeoxycholate, sodium glycocholate, sodium glycodeoxycholate, and sodium dodecyl sulfate......), a cationic surfactant (benzalkonium chloride), and a neutral surfactant (Triton X-100) were studied. The anionic surfactants increased the insulin release in a concentration-dependent manner, whereas the neutral surfactant had no significant effect on the release. Interestingly, only minute amounts...

  5. Effect of a Long Chain Carboxylate Acid on Sodium Dodecyl Sulfate Micelle Structure: A Small-angle Neutron Scattering Study

    International Nuclear Information System (INIS)

    Arum Patriati; Edy Giri Rachman Putra

    2009-01-01

    The effect of different hydrocarbon chain length of carboxylate acid, i.e. dodecanoic acid, CH 3 (CH 2 ) 10 COOH and hexadecanoic acid, CH 3 (CH 2 ) 14 COOH as a co-surfactant in the 0.3M SDS micellar solution has been studied using small angle neutron scattering (SANS). Here, the present of dodecanoic acid has induced the SDS structural micelles. The ellipsoid micelles structures changed significantly in length (major axis) from 21.7 Armstrong to 35.5 Armstrong at a fixed minor axis of 16.7 Armstrong in the present of 0.005M to 0.1M dodecanoic acid. Nevertheless, this effect was not shown in the present of hexadecanoic acid with the same concentration range. The present of hexadecanoic acid molecules gave a small effect on growth of SDS micelles where the major axis of the micelle was simply elongated from 21.5 Armstrong to 23.5 Armstrong. It showed that the appropriate hydrocarbon chain length between surfactant and co-surfactant molecules is one of the determining factors in forming a mixed micelles structure. (author)

  6. Conformational studies of human [15-2-aminohexanoic acid]little gastrin in sodium dodecyl sulfate micelles by 1H NMR

    International Nuclear Information System (INIS)

    Mammi, S.; Peggion, E.

    1990-01-01

    Human little gastrin is a 17 amino acid peptide that adopts a random conformation in water and an ordered structure in sodium dodecyl sulfate (SDS) micelles as well as in trifluoroethanol (TFE). The circular dichroism spectra in these two media have the same shape, indicative of a similar preferred conformation. The authors describe here the assignment of the proton NMR resonances and the conformational analysis of [Ahx 15 ] little gastrin in SDS micelles. Two-dimensional correlation techniques form the basis for the assignment. The conformational analysis utilizes NOE's, NH to C α H coupling constants, and the temperature coefficients of the amide chemical shifts. The NMR data indicate a helical structure in the N-terminal portion of the peptide. These results are compared with the conformation that the authors recently proposed for a minigastrin analogue (fragment 5-17 of [Ahx 15 ] little gastrin) in TFE

  7. Efficacy and compatibility with mass spectrometry of methods for elution of proteins from sodium dodecyl sulfate-polyacrylamide gels and polyvinyldifluoride membranes

    DEFF Research Database (Denmark)

    Jørgensen, C.S.; Jagd, M.; Sørensen, B.K.

    2004-01-01

    The resolving power of sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) combined with isoelectric focusing in two-dimensional gel electrophoresis has made it one of the most important techniques for resolving complex mixtures, and it is of great importance for proteome mapping...... for recovering intact proteins from polyacrylamide gels and electroblotting membranes to define efficient methods compatible with MS. These methods complement in situ digestion protocols and allow determination of the molecular mass of whole proteins separated by SDS-PAGE. Passive elution of proteins from SDS......-PAGE gels was efficient only in the presence of SDS, whereas electroelution was achieved using butTers without SDS. Surface-enhanced laser desorption/ionization MS (SELDI-MS) analysis of proteins eluted in the presence of SIDS was possible using ion exchange ProteinChip arrays for concentration of sample...

  8. Dielectric study of aqueous solutions of sodium dodecyl sulfate in the frequency span 20 Hz to 2 MHz

    Science.gov (United States)

    Kadve, A. M.; Vankar, H. P.; Rana, V. A.

    2017-05-01

    Dielectric measurements were carried out for aqueous solutions of Sodium Dodecyl Sulfate (SDS) in the frequency span of 20 Hz to 2 MHz at 300.15 K temperature using precision LCR meter. Also the refractive indices were measured for the solutions at 300.15 K temperature using Abbe's refractometer. The measurements were done for ten different concentrations of SDS in distilled water. Determined values of complex permittivity as a function of frequency were used to evaluate other parameters like loss tangent and electric modulus for the liquid samples. The permittivity at optical frequency were also calculated from the measured refractive indices for the aqueous solutions. The effect of concentration variation of SDS in the aqueous solutions on the determined parameters is discussed.

  9. Interaction between sodium dodecyl sulfate and membrane reconstituted aquaporins: A comparative study of spinach SoPIP2;1 and E. coli AqpZ

    DEFF Research Database (Denmark)

    Hansen, Jesper Schmidt; Vararattanavech, Ardcharaporn; Plasencia, Inés

    2011-01-01

    This study describes the interaction between sodium dodecyl sulfate (SDS) and membrane proteins reconstituted into large unilamellar lipid vesicles and detergent micelles studied by circular dichroism (CD) and polarity sensitive probe labeling. Specifically, we carried out a comparative study...... aquaporins. However, we do not find compelling evidence for unfolding. In contrast when SDS is added to detergent stabilized aquaporins, SoPIP2;1 partly unfolds, while AqpZ secondary structure is unaffected. Using a fluorescent polarity sensitive probe (Badan) we show that SDS action on membrane...... to 12.5× CMC. Combined, our results show that SDS does not unfold neither SoPIP2;1 nor AqpZ during transition from a membrane reconstituted form to a detergent stabilized state albeit the native folds are changed....

  10. Characterization of Sm14 related components in different helminths by sodium dodecyl sulphate-polyacrylamide gel electrophoresis and Western blotting analysis

    Directory of Open Access Journals (Sweden)

    Nilton Thaumaturgo

    2002-10-01

    Full Text Available Sm14 was the first fatty acid-binding protein homologue identified in helminths. Thereafter, members of the same family were identified in several helminth species, with high aminoacid sequence homology between them. In addition, immune crossprotection was also reported against Fasciola hepatica infection, in animals previously immunized with the Schistosoma mansoni vaccine candidate, r-Sm14. In the present study, data on preliminary sodium dodecyl sulphate-polyacrylamide gel electrophoresis and Western blotting analysis of nine different helminth extracts focusing the identification of Sm14 related proteins, is reported. Out of these, three extracts - Ascaris suum (males and females, Echinostoma paraensei, and Taenia saginata - presented components that comigrated with Sm14 in SDS-PAGE, and that were recognized by anti-rSm14 policlonal serum, in Western blotting tests.

  11. Determination of albumins by its quenching effect on the fluorescence of Tb{sup 3+}-oxolinic acid complex in presence of sodium dodecyl sulphate

    Energy Technology Data Exchange (ETDEWEB)

    Wu Xia [Key Laboratory of Colloid and Interface Chemistry (Shandong University), Ministry of Education, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China); Zheng Jinhua [Key Laboratory of Colloid and Interface Chemistry (Shandong University), Ministry of Education, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China); Guo Changying [Key Laboratory of Colloid and Interface Chemistry (Shandong University), Ministry of Education, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China); Yang Jinghe [Key Laboratory of Colloid and Interface Chemistry (Shandong University), Ministry of Education, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China)]. E-mail: yjh@sdu.edu.cn; Ding Honghong [Key Laboratory of Colloid and Interface Chemistry (Shandong University), Ministry of Education, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China); Hu Zhiyong [Key Laboratory of Colloid and Interface Chemistry (Shandong University), Ministry of Education, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China); Li Chao [Key Laboratory of Colloid and Interface Chemistry (Shandong University), Ministry of Education, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China)

    2007-09-15

    It is found that the fluorescence intensity of Tb{sup 3+}-oxolinic acid (OA) complex can be greatly quenched by albumins in sodium dodecyl sulphate (SLS). Under optimum conditions, the quenched fluorescence intensity is in proportion to the concentration of proteins in the range of 5.0x10{sup -8}-1.0x10{sup -5} g ml{sup -1} for bovine serum albumin (BSA), 1.0x10{sup -7}-1.0x10{sup -5} g ml{sup -1} for human serum albumin (HSA) and 4.0x10{sup -7}-1.0x10{sup -5} g ml{sup -1} for egg albumin (EA). Their detection limits (S/N=3) are 2.1x10{sup -8}, 2.5x10{sup -8} and 5.0x10{sup -8} g ml{sup -1}, respectively. In addition, the interaction mechanism is also investigated.

  12. Experimental Analysis for the Use of Sodium Dodecyl Sulfate as a Soluble Metal Cutting Fluid for Micromachining with Electroless-Plated Micropencil Grinding Tools

    Directory of Open Access Journals (Sweden)

    Peter A. Arrabiyeh

    2017-11-01

    Full Text Available Microgrinding with micropencil grinding tools (MPGTs is a flexible and economic process to machine microstructures in hard and brittle materials. In macrogrinding, cooling and lubrication are done with metal cutting fluids; their application and influence is well researched. Although it can be expected that metal cutting fluids also play a decisive role in microgrinding, systematic investigations can hardly be found. A metal cutting fluid capable of wetting the machining process, containing quantities as small as 0.02% of the water-soluble fluid sodium dodecyl sulfate was tested in microgrinding experiments with MPGTs (diameter ~50 µm; abrasive grit size 2–4 µm. The workpiece material was hardened 16MnCr5.

  13. Cationic versus anionic surfactant in tuning the structure and interaction of nanoparticle, protein, and surfactant complexes.

    Science.gov (United States)

    Mehan, Sumit; Aswal, Vinod K; Kohlbrecher, Joachim

    2014-08-26

    The structure and interaction in complexes of anionic Ludox HS40 silica nanoparticle, anionic bovine serum albumin (BSA) protein, and cationic dodecyl trimethylammonium bromide (DTAB) surfactant have been studied using small-angle neutron scattering (SANS). The results are compared with similar complexes having anionic sodium dodecyl sulfate (SDS) surfactant (Mehan, S; Chinchalikar, A. J.; Kumar, S.; Aswal, V. K.; Schweins, R. Langmuir 2013, 29, 11290). In both cases (DTAB and SDS), the structure in nanoparticle-protein-surfactant complexes is predominantly determined by the interactions of the individual two-component systems. The nanoparticle-surfactant (mediated through protein-surfactant complex) and protein-surfactant interactions for DTAB, but nanoparticle-protein (mediated through protein-surfactant complex) and protein-surfactant interactions for SDS, are found to be responsible for the resultant structure of nanoparticle-protein-surfactant complexes. Irrespective of the charge on the surfactant, the cooperative binding of surfactant with protein leads to micellelike clusters of surfactant formed along the unfolded protein chain. The adsorption of these protein-surfactant complexes for DTAB on oppositely charged nanoparticles gives rise to the protein-surfactant complex-mediated aggregation of nanoparticles (similar to that of DTAB surfactant). It is unlike that of depletion-induced aggregation of nanoparticles with nonadsorption of protein-surfactant complexes for SDS in similarly charged nanoparticle systems (similar to that of protein alone). The modifications in nanoparticle aggregation as well as unfolding of protein in these systems as compared to the corresponding two-component systems have also been examined by selectively contrast matching the constituents.

  14. Mixed hemimicelles solid-phase extraction based on sodium dodecyl sulfate-coated nano-magnets for selective adsorption and enrichment of illegal cationic dyes in food matrices prior to high-performance liquid chromatography-diode array detection detection.

    Science.gov (United States)

    Qi, Ping; Liang, Zhi-An; Wang, Yu; Xiao, Jian; Liu, Jia; Zhou, Qing-Qiong; Zheng, Chun-Hao; Luo, Li-Ni; Lin, Zi-Hao; Zhu, Fang; Zhang, Xue-Wu

    2016-03-11

    In this study, mixed hemimicelles solid-phase extraction (MHSPE) based on sodium dodecyl sulfate (SDS) coated nano-magnets Fe3O4 was investigated as a novel method for the extraction and separation of four banned cationic dyes, Auramine O, Rhodamine B, Basic orange 21 and Basic orange 22, in condiments prior to HPLC detection. The main factors affecting the extraction of analysts, such as pH, surfactant and adsorbent concentrations and zeta potential were studied and optimized. Under optimized conditions, the proposed method was successful applied for the analysis of banned cationic dyes in food samples such as chili sauce, soybean paste and tomato sauce. Validation data showed the good recoveries in the range of 70.1-104.5%, with relative standard deviations less than 15%. The method limits of determination/quantification were in the range of 0.2-0.9 and 0.7-3μgkg(-1), respectively. The selective adsorption and enrichment of cationic dyes were achieved by the synergistic effects of hydrophobic interactions and electrostatic attraction between mixed hemimicelles and the cationic dyes, which also resulted in the removal of natural pigments interferences from sample extracts. When applied to real samples, RB was detected in several positive samples (chili powders) within the range from 0.042 to 0.177mgkg(-1). These results indicate that magnetic MHSPE is an efficient and selective sample preparation technique for the extraction of banned cationic dyes in a complex matrix. Copyright © 2016 Elsevier B.V. All rights reserved.

  15. A Novel Method for Detection of Glycoproteins on Sodium Dodecyl Sulphate Polyacrylamide Gel Using Radio-Iodinated Tyrosine

    DEFF Research Database (Denmark)

    Nalla, Amarnadh; Draz, Hossam M.; Dole, Anita

    2009-01-01

    A (Con A) were used as a glycosylated and a non-glycosylated model proteins, respectively. The proteins were separated in SDS- PAGE and oligosaccharides on the glycoprotein were oxidised using periodic acid to produce aldehydes than 125I-tyroine was conjugated to aldehyde groups without using reducing...... agent like Sodium Metabisulfite. The radio-iodinated glycoprotein on gel was scanned using a Multi-Photon Detection (MPD) scanner. The elechtrophoretic analysis of ovalbumin and Con A were performed and stained with Coomassie brilliant blue to identify total proteins, while MPD detection...... of glycoproteins using 125I-tyrosine selectively detected ovalbumin. Present results showed that MPD enhanced glycoprotein detection method can be used as a sensitive tool for the detection of glycoproteins on polyacrylamide gel...

  16. Selective entrapment of the cationic form of norfloxacin within anionic sodium dodecyl sulfate micelles at physiological pH and its effect on the drug photodecomposition.

    Science.gov (United States)

    Sortino, Salvatore

    2006-01-01

    The binding of the photosensitizing fluoroquinolone (FQ) antibiotic norfloxacin (NX) to sodium dodecyl sulfate (SDS) micelles and the photoreactivity of the NX/SDS complex under physiological pH conditions are investigated by means of absorption and emission spectroscopy, steady-state and laser flash photolysis. It is shown that the photolabile zwitterionic form of NX, which is dominant at physiological pH, is not the most abundant species in the presence of SDS micelles. This medium exhibits a high preference for the cationic form of the drug, which is selectively and successfully entrapped within the micellar cage (K(ass) = 6 x 10(4) M(-1) +/- 3000), becoming the largely dominant species at neutral pH. The effect of this trapping is drastically reflected on both efficiency and nature of the drug photodecomposition. It is observed that the photostability of NX incorporated in the micellar pseudophase increases of more than one order of magnitude if compared to that of the "free" drug. Furthermore, the radical photodecomposition mechanism occurring in phosphate buffered solution is suppressed by the micellar medium and the low photodegradation observed seems to take place preferentially through an ionic pathway. Hopefully, the results presented herein may contribute to a better understanding of the bio-distribution of NX in biological systems and provide helpful and stimulating information in order to get the control of FQ photoreactivity under physiological pH conditions.

  17. Structural and phase transition changes of sodium dodecyl sulfate micellar solution in alcohols probed by small-angle neutron scattering (SANS)

    International Nuclear Information System (INIS)

    Putra, Edy Giri Rachman; Patriati, Arum

    2015-01-01

    Small-angle neutron scattering (SANS) measurements on 0.3M sodium dodecyl sulfate (SDS) micellar solutions have been performed in the presence of n-alcohols, from ethanol to decanol at different alcohol concentrations, 2–10 wt%. The ellipsoid micellar structure which occurred in the 0.3M SDS in aqueous solution with the size range of 30–50 Å has different behavior at various hydrocarbon chain length and concentration of alcohols. At low concentration and short chain-length of alcohols, such as ethanol, propanol, and butanol, the size of micelles reduced and had a spherical-like structure. The opposite effect occurred as medium to long chain alcohols, such as hexanol, octanol and decanol was added into the 0.3M SDS micellar solutions. The micelles structure changed to be more elongated in major axis and then crossed the critical phase transition from micellar solution into liquid crystal phase as lamellar structure emerged by further addition of alcohols. The inter-lamellar distances were also depending on the hydrocarbon chain length and concentration of alcohols. In the meantime, the persistent micellar structures occurred in addition of medium chain of n-alcohol, pentanol at all concentrations

  18. Thermodynamic characteristics of the dissolution of glycine, glycylglycine, and glycylglycylglycine in aqueous solutions of sodium dodecyl sulfate at T = 298.15 K

    Science.gov (United States)

    Smirnov, V. I.; Badelin, V. G.

    2017-09-01

    the enthalpies of dissolution of glycine (Gly), glycylglycine (GlyGly), and glycylglycylglycine (GlyGlyGly) are measured in aqueous solutions of sodium dodecyl sulfate (SDS) at SDS concentrations m = 0-0.7 mol kg-1 and T = 298.15 K by means of calorimetry. The obtained data are used to calculate the standard values of enthalpies of dissolution (Δsol H m ) and enthalpies of transfer (Δtr H m ) of glycine and its oligomers from water to SDS aqueous solutions. The dependences of Δsol H m and Δtr H m on SDS concentration in an aqueous solution at a constant concentration of glycine and its oligomers are determined. A comparative analysis of the thermodynamic characteristics of Gly, GlyGly, and GlyGlyGly transfer within the studied range of SDS concentrations is performed. The results are interpreted in terms of ion-ion, ion-polar, and hydrophobic interactions between SDS and molecules of glycine and its oligomers.

  19. Inactivation of Escherichia coli O157:H7 and Salmonella during washing of contaminated gloves in levulinic acid and sodium dodecyl sulfate solutions.

    Science.gov (United States)

    Erickson, Marilyn C; Liao, Jye-Yin; Habteselassie, Mussie Y; Cannon, Jennifer L

    2018-08-01

    Field workers often wear gloves harvesting ready-to-eat produce; however, fields are not sterile environments and gloves may become contaminated numerous times during a working shift. This study explored the potential for inactivation of Escherichia coli O157:H7 and Salmonella when contaminated gloves were washed in levulinic acid (LV) and sodium dodecyl sulfate (SDS) solutions. Washing nitrile gloves with increasing concentrations of LV above 1.0% led to a decreased prevalence of glove contamination by Salmonella (P = 0.0000). A higher level of prevalence occurred for solid agar-cultured pathogens than liquid broth-cultured pathogens after nitrile gloves were washed in LV/SDS (P = 0.0000). Pathogens residing on latex gloves were more likely to be completely inactivated by washing in 0.5% LV/0.1% SDS solutions than nitrile or Canners gloves that exhibited inconsistent responses dependent on the pathogen strain. However, drying after washing nitrile gloves in 0.5% LV/0.1% SDS led to additional pathogen inactivation (P = 0.0394). Pathogen transfer from gloves to produce was implied as the pathogen prevalence on cantaloupe rind handled by LV/SDS-washed gloves was not statistically different from the prevalence on gloves (P = 0.7141). Hence, the risk of produce contamination may still exist but would be reduced by washing gloves in LV/SDS. Copyright © 2018 Elsevier Ltd. All rights reserved.

  20. Structural and phase transition changes of sodium dodecyl sulfate micellar solution in alcohols probed by small-angle neutron scattering (SANS)

    Energy Technology Data Exchange (ETDEWEB)

    Putra, Edy Giri Rachman [Neutron Scattering Laboratory, National Nuclear Energy Agency of Indonesia (BATAN), Gedung 40 BATAN, Kawasan Puspiptek Serpong, Tangerang 15314 (Indonesia); Patriati, Arum [Neutron Scattering Laboratory, National Nuclear Energy Agency of Indonesia (BATAN), Gedung 40 BATAN, Kawasan Puspiptek Serpong, Tangerang 15314 (Indonesia); Department of Chemistry, Faculty of Mathematics and Natural Sciences, University of Gadjah Mada, Bulaksumur, Yogyakarta 55281, Indonesia giri@batan.go.id (Indonesia)

    2015-04-16

    Small-angle neutron scattering (SANS) measurements on 0.3M sodium dodecyl sulfate (SDS) micellar solutions have been performed in the presence of n-alcohols, from ethanol to decanol at different alcohol concentrations, 2–10 wt%. The ellipsoid micellar structure which occurred in the 0.3M SDS in aqueous solution with the size range of 30–50 Å has different behavior at various hydrocarbon chain length and concentration of alcohols. At low concentration and short chain-length of alcohols, such as ethanol, propanol, and butanol, the size of micelles reduced and had a spherical-like structure. The opposite effect occurred as medium to long chain alcohols, such as hexanol, octanol and decanol was added into the 0.3M SDS micellar solutions. The micelles structure changed to be more elongated in major axis and then crossed the critical phase transition from micellar solution into liquid crystal phase as lamellar structure emerged by further addition of alcohols. The inter-lamellar distances were also depending on the hydrocarbon chain length and concentration of alcohols. In the meantime, the persistent micellar structures occurred in addition of medium chain of n-alcohol, pentanol at all concentrations.

  1. Efficacy of a Levulinic Acid Plus Sodium Dodecyl Sulfate (SDS)-Based Sanitizer on Inactivation of Influenza A Virus on Eggshells.

    Science.gov (United States)

    Aydin, Ali; Cannon, Jennifer L; Zhao, Tong; Doyle, Michael P

    2013-10-17

    Influenza A virus poses a major public health concern and is associated with annual epidemics and occasional pandemics. Influenza A H3N2 viruses, which are an important cause of human influenza, can infect birds and mammals. Contaminated undercooked poultry products including eggs with avian influenza virus constitute a possible risk of transmission to humans. In this study, a novel levulinic acid plus sodium dodecyl sulfate (SDS) sanitizer was evaluated for eggshell decontamination. Influenza A H3N2 virus-inoculated chicken eggshells were treated with a 5 % levulinic acid plus 2 % SDS, 2 % levulinic acid plus 1 % SDS, and 0.5 % levulinic acid plus 0.5 % SDS liquid solution for 1 min. Log reductions of viable viruses were observed by plaque assay. The 5 % levulinic acid plus 2 % SDS sanitizer provided the greatest level of influenza A H3N2 virus inactivation (2.23 log PFU), and differences in virus inactivation were observed for the various levulinic acid plus SDS concentrations tested (P ≤ 0.05). To the best of our knowledge, this is the first study demonstrating influenza A H3N2 virus inactivation on eggshells using a novel levulinic acid plus SDS sanitizer. The sanitizer may be useful for reducing egg contamination and preventing the spread of avian influenza virus to humans.

  2. Electrophoretic analysis of proteinases in sodium dodecyl sulfate-polyacrylamide gels containing copolymerized radiolabeled protein substrates: Application to proenkephalin processing enzymes

    Energy Technology Data Exchange (ETDEWEB)

    Irvine, J.W.; Roberts, S.F.; Lindberg, I. (Louisiana State Univ. Medical Center, New Orleans (USA))

    1990-10-01

    A novel method is described for the zymographic analysis of proteinases in sodium dodecyl sulfate-polyacrylamide gels containing copolymerized radiolabeled protein substrates such as ({sup 35}S)methionine-labeled proenkephalin or {sup 125}I-labeled proinsulin. After electrophoresis the enzyme is reactivated and cleaves the radiolabeled in situ substrate into smaller peptides. These small peptides are able to diffuse out of the gel, leaving clear areas against a dark background when visualized by autoradiography. The technique can be used to detect as little as 200 fg of trypsin using only 50 ng (1.25 microCi) of ({sup 35}S)proenkephalin. Soluble- and membrane-bound adrenal trypsin-like enzyme were isolated from bovine adrenal chromaffin granules. Both proteinases cleaved ({sup 35}S)methionine-labeled proenkephalin but not {sup 125}I-labeled proinsulin. Moreover, both had a Mr of approximately 30,000. The potential of this technique for general use is discussed. An additional method using the synthetic fluorogenic substrate t-butoxycarbonyl Glu-Lys-Lys aminomethylcoumarin is also described.

  3. Thermochemistry of the Dissolution of Dipeptides Containing DL-α-Alanine in Aqueous Solutions of Sodium Dodecyl Sulfate at 298.15 K

    Science.gov (United States)

    Smirnov, V. I.; Badelin, V. G.

    2018-05-01

    Enthalpies of the dissolution of DL-α-alanylglycine (AlaGly), DL-α-alanyl-DL-α-alanine (AlaAla), DL-α-alanyl-DL-α-valine (AlaVal), and DL-α-alanyl-DL-norleucine (AlaNln) in an aqueous solution of sodium dodecyl sulfate (SDS) at SDS concentration of m = 0-0.07 mol kg-1 and temperature T = 298.15 K are measured via calorimetry. The standard values of the enthalpy of dissolution (Δsol H m ) and the transfer of dipeptides (Δtr H m ) from water to aqueous SDS solutions are calculated using the experimental data. The dependences of Δsol H m and Δtr H m the SDS concentration at a constant concentration of dipeptide are established. Thermochemical characteristics of the transfer of AlaGly, AlaAla, AlaVal, and AlaNln in the investigated range of SDS concentrations are compared. The results are interpreted by considering ion-ion, ion-polar, and hydrophobic-hydrophobic interactions between SDS and dipeptide molecules.

  4. 2,4-Dinitrophenylhydrazine functionalized sodium dodecyl sulfate-coated magnetite nanoparticles for effective removal of Cd(II) and Ni(II) ions from water samples.

    Science.gov (United States)

    Sobhanardakani, Soheil; Zandipak, Raziyeh

    2015-07-01

    2,4-Dinitrophenylhydrazine immobilized on sodium dodecyl sulfate (SDS)-coated magnetite and was used for removal of Cd(II) and Ni(II) ions from aqueous solution. The prepared product was characterized by X-ray diffraction (XRD) analysis, Fourier transform infrared spectroscopy (FT-IR), and scanning electron microscopy (SEM). The size of the nanoparticles according to SEM was obtained around 20-35 nm. In batch tests, the effects of pH, contact time, initial metal concentration, and temperature were studied. The kinetic and equilibrium data were modeled with recently developed models. The adsorption kinetics and isotherms were well fitted by the fractal-like pseudo-second-order model and Langmuir-Freundlich model, respectively. Maximum adsorption capacity by this adsorbent is 255.1 mg g(-1) for Cd(II) ion and 319.6 mg g(-1) for Ni(II) ion at pH 7.0 and 25 °C. The method was successfully applied to the removal of metal cations in real samples (tap water, river water, and petrochemical wastewater).

  5. Use of PCR and Sodium Dodecyl Sulfate-Polyacrylamide Gel Electrophoresis Techniques for Differentiation of Prevotella intermedia Sensu Stricto and Prevotella nigrescens

    Science.gov (United States)

    Premaraj, Thyagaseely; Kato, Naoki; Fukui, Katsuhito; Kato, Haru; Watanabe, Kunitomo

    1999-01-01

    Primers were designed from 16S rRNA sequences of Prevotella intermedia sensu stricto and Prevotella nigrescens and were used to discriminate these two species by PCR. The results were compared with those from the PCR technique using primers designed from arbitrarily primed PCR products by Guillot and Mouton (E. Guillot and C. Mouton, J. Clin. Microbiol. 35:1876–1882, 1997). The specificities of both assays were studied by using P. intermedia ATCC 25611, P. nigrescens ATCC 33563, 174 clinical isolates of P. intermedia sensu lato, and 59 reference strains and 58 clinical isolates of other Prevotella species and/or common oral flora. In addition, the usefulness and reliability of sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) in the differentiation of the two species were examined by comparing the results with those from PCR assays. The controversial lipase test for distinguishing these species was also carried out. Unambiguous differentiation was made by both PCR assays, and the results matched each other. The SDS-PAGE assay was found to misidentify a few strains tested, compared with the results of PCR assays. The lipase test was positive for both species, including the reference strains of P. intermedia and P. nigrescens. We conclude that both PCR assays are simple, rapid, reliable, and specific methods which could be used in clinical studies and that the lipase test is not valuable in the differentiation. The reliable discrimination of the two species by SDS-PAGE is questionable. PMID:10074526

  6. Inactivation of Escherichia coli O157:H7 and Salmonella typhimurium DT 104 on alfalfa seeds by levulinic acid and sodium dodecyl sulfate.

    Science.gov (United States)

    Zhao, Tong; Zhao, Ping; Doyle, Michael P

    2010-11-01

    Studies were conducted to determine the best concentration and exposure time for treatment of alfalfa seeds with levulinic acid plus sodium dodecyl sulfate (SDS) to inactivate Escherichia coli O157:H7 and Salmonella without adversely affecting seed germination. Alfalfa seeds inoculated with a five-strain mixture of E. coli O157:H7 or Salmonella Typhimurium were dried in a laminar flow hood at 21°C for up to 72 h. Inoculated alfalfa seeds dried for 4 h then treated for 5 min at 21°C with 0.5% levulinic acid and 0.05% SDS reduced the population of E. coli O157:H7 and Salmonella Typhimurium by 5.6 and 6.4 log CFU/g, respectively. On seeds dried for 72 h, treatment with 0.5% levulinic acid and 0.05% SDS for 20 min at 21°C reduced E. coli O157:H7 and Salmonella Typhimurium populations by 4 log CFU/g. Germination rates of alfalfa seeds treated with 0.5% levulinic acid plus 0.05% SDS for up to 1 h at 21°C were compared with a treatment of 20,000 ppm of calcium hypochlorite or tap water only. Treatment of alfalfa seeds with 0.5% levulinic acid plus 0.05% SDS for 5 min at 21°C resulted in a >3.0-log inactivation of E. coli O157:H7 and Salmonella.

  7. Inactivation of Salmonella and Escherichia coli O157:H7 on lettuce and poultry skin by combinations of levulinic acid and sodium dodecyl sulfate.

    Science.gov (United States)

    Zhao, Tong; Zhao, Ping; Doyle, Michael P

    2009-05-01

    Four organic acids (lactic acid, acetic acid, caprylic acid, and levulinic acid) and sodium dodecyl sulfate (SDS) were evaluated individually or in combination for their ability to inactivate Salmonella and Escherichia coli O157:H7. Results from pure culture assays in water with the treatment chemical revealed that 0.5% organic acid and 0.05 to 1% SDS, when used individually, reduced pathogen cell numbers by acids at 0.5% with 0.05% SDS resulted in > 7 log CFU/ml inactivation of Salmonella and E. coli O157:H7 within 10 s at 21 degrees C. A combination of levulinic acid and SDS was evaluated at different concentrations for pathogen reduction on lettuce at 21 degrees C, on poultry (wings and skin) at 8 degrees C, and in water containing chicken feces or feathers at 21 degrees C. Results revealed that treatment of lettuce with a combination of 3% levulinic acid plus 1% SDS for 6.7 log CFU/g on lettuce. Salmonella and aerobic bacterial populations on chicken wings were reduced by > 5 log CFU/g by treatment with 3% levulinic acid plus 2% SDS for 1 min. Treating water heavily contaminated with chicken feces with 3% levulinic acid plus 2% SDS reduced Salmonella populations by > 7 log CFU/ml within 20 s. The use of levulinic acid plus SDS as a wash solution may have practical application for killing foodborne enteric pathogens on fresh produce and uncooked poultry.

  8. Detection of metalloproteins in human liver cytosol by synchrotron radiation X-ray fluorescence after sodium dodecyl sulphate polyacrylamide gel electrophoresis

    International Nuclear Information System (INIS)

    Gao Yuxi; Chen Chunying; Zhang Peiqun; Chai Zhifang; He Wei; Huang Yuying

    2003-01-01

    An improved method of analysis of metals in protein bands with synchrotron radiation X-ray fluorescence (SRXRF) after sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) separation is introduced and applied to human liver cytosol. Through a step of drying the gel before SRXRF determination, the continuous background resulting mainly from the Compton-scattering of X-rays by the gel matrix was substantially reduced, and the detection of biological trace elements, such as Cu, Fe, and Zn in protein bands was thereby made possible. With the new procedure, six Zn-containing proteins with molecular weights (MWs) of 17.5, 20.5, 27, 35, 55, and 63 kDa, respectively were found in human liver cytosol, among which the 63 kDa Zn-containing band was shown to be the dominant form of zinc. In addition, at least four Fe containing proteins with MWs of 20, 23, 43, and 83.5 kDa, respectively, were present in the samples. The metal contents in some metalloproteins, such as the 63 kDa Zn-containing protein, the 23 and 83.5 kDa Fe-containing proteins, and a 22 kDa Cu-containing protein were more closely related to the metal level in the sample. It is demonstrated that the procedure could be widely used to further investigate metal-binding proteins in biological samples

  9. Voltammetric determination of sudan ii in food samples at graphene modified glassy carbon electrode based on the enhancement effect of sodium dodecyl sulfate

    International Nuclear Information System (INIS)

    Ma, X.; Chen, M.; Chao, M.

    2013-01-01

    Summary: Herein, a novel electrochemical method was de veloped for the determination of Sudan II based on the electrochemical catalytic activity of graphene modified glassy carbon electrode (GME) and the enhancement effect of sodium dodecyl sulfate (SDS). In a pH 6.0 phosphate buffer solution, Sudan II exhibited a pair of well-defined quasi reversible redox peaks at the GME in the presence of 5.0x10/sup -5/ mol L/sup 1/ SDS. The oxidation peak current of Sudan II was linearly proportional to its concentration in a range from 4.0x10/sup -8/ to 4.0x10/sup -6/ mol L/sup 1/, with a linear regression equation of ipa (A) = 3.35 c + 5.96 x 10/sup -6/, r = 0.9988 and a detection limit of 8.0x10/sup -9/ mol L/sup 1/. The recoveries from the standards fortified blank samples were in the range of 94.7% to 97.5% with RSD lower than 4.0%. The novel method has been successfully used to determine Sudan II in food products with satisfactory results. (author)

  10. Inactivation of viruses and bacteria on strawberries using a levulinic acid plus sodium dodecyl sulfate based sanitizer, taking sensorial and chemical food safety aspects into account.

    Science.gov (United States)

    Zhou, Zijin; Zuber, Sophie; Cantergiani, Frédérique; Butot, Sophie; Li, Dan; Stroheker, Thomas; Devlieghere, Frank; Lima, Anthony; Piantini, Umberto; Uyttendaele, Mieke

    2017-09-18

    The efficacy of levulinic acid (LVA) in combination with sodium dodecyl sulfate (SDS) in removal of foodborne viruses, enteric bacterial pathogens and their surrogates on fresh strawberries was investigated. Inoculated strawberries were treated with potable water, sodium hypochlorite solution (50ppm), 0.5% LVA plus 0.5% SDS solution, and 5% LVA plus 2% SDS solution respectively for 2min, followed by spray-rinsing with potable water. Water washing removed at least 1.0-log of the tested viral and bacterial strains from the strawberries' surfaces. The 50ppm chlorine wash induced 3.4, 1.5 and 2.1-log reductions for hepatitis A virus (HAV), murine norovirus-1 (MNV-1) and MS2 bacteriophage, respectively. In comparison, the tested bacterial strains showed uniform reductions around 1.6-log CFU/ml. The 0.5% LVA plus 0.5% SDS wash induced 2.7, 1.4 and 2.4-log reductions for HAV, MNV-1 and MS2, which were comparable with the reductions induced by chlorine (P>0.05). For bacteria, over 2.0-log reductions were obtained for Enterococcus faecium, Listeria monocytogenes and Salmonella, while Escherichia coli O157:H7 and Escherichia coli P1 showed reductions of 1.9 and 1.8-log CFU/ml. Higher concentration of LVA plus SDS showed no significantly higher reductions (P>0.05). Sensory tests of washed strawberries and chemical residue analysis of LVA on strawberries after washing were also performed. In conclusion, this study demonstrates good performance of 0.5% LVA plus 0.5% SDS to reduce the levels of enteric pathogens if present on strawberries without altering taste and introducing chemical safety issues. Copyright © 2017 Elsevier B.V. All rights reserved.

  11. Acids in combination with sodium dodecyl sulfate caused quality deterioration of fresh-cut iceberg lettuce during storage in modified atmosphere package.

    Science.gov (United States)

    Guan, Wenqiang; Huang, Lihan; Fan, Xuetong

    2010-10-01

    Recent studies showed that sodium acid sulfate (SAS) and levulinic acid (LA) in combination with sodium dodecyl sulfate (SDS) was effective in inactivating human pathogens on Romaine lettuce. The present study investigated the effects of LA and SAS in combination with SDS (as compared with citric acid and chlorine) on the inactivation of E. coli O157:H7 and sensory quality of fresh-cut Iceberg lettuce in modified atmosphere packages during storage at 4 °C. Results showed that LA (0.5% to 3%) and SAS (0.25% to 0.75%) with 0.05% SDS caused detrimental effects on visual quality and texture of lettuce. LA- and SAS-treated samples were sensorially unacceptable due to development of sogginess and softening after 7 and 14 d storage. It appears that the combined treatments caused an increase in the respiration rate of fresh-cut lettuce as indicated by higher CO(2) and lower O(2) in modified atmosphere packages. On the positive side, the acid treatments inhibited cut edge browning of lettuce pieces developed during storage. LA (0.5%), SAS (0.25%), and citric acid (approximately 0.25%) in combination with SDS reduced population of E. coli OH157:H7 by 0.41, 0.87, and 0.58 log CFU/g, respectively, while chlorine achieved a reduction of 0.94 log CFU/g without damage to the lettuce. Therefore, compared to chlorine, LA and SAS in combination with SDS have limited commercial value for fresh-cut Iceberg lettuce due to quality deterioration during storage.

  12. The impact of alkyl sulfate surfactant geometry and electrolyte on the co-adsorption of anionic surfactants with model perfumes at the air-solution interface.

    Science.gov (United States)

    Bradbury, Robert; Penfold, Jeffrey; Thomas, Robert K; Tucker, Ian M; Petkov, Jordan T; Jones, Craig

    2013-08-01

    The impact of surfactant geometry and electrolyte on the co-adsorption of anionic surfactants and model perfumes at the air-solution interface has been studied by neutron reflectivity. The more hydrophobic perfume linalool, competes more favourably for the surface with sodium dodecylsulfate than was previously reported for the anionic surfactant, sodium dodecyl 6-benzenesulfonate. Due to an increase in surface activity of the sodium dodecylsulfate, the addition of electrolyte results in a reduction in the linalool adsorption. Changing the alkyl chain length affects the relative adsorption of linalool and surfactant at the interface. Similar measurements for the different alkyl sulfates and with electrolyte with the more hydrophilic perfume phenyl ethanol, reveal broadly similar trends. Although the relative adsorption of phenyl ethanol with sodium dodecylsulfate is substantially enhanced compared to sodium dodecyl-6-benzenesulfonate the effects are not as significant as was observed with linalool. The variations with alkyl chain geometry show the importance of the hydrophobic interaction between the perfume and surfactant and changes in the packing constraints on the relative adsorption. The results highlight the importance of the specific interaction between the surfactant and perfume, and the surfactant and perfume geometries on the relative adsorption at the interface. Copyright © 2013 Elsevier Inc. All rights reserved.

  13. Modulation of the wettability of excipients by surfactant and its impacts on the disintegration and release of tablets.

    Science.gov (United States)

    Yang, Baixue; Xu, Lu; Wang, Qiuxiao; Li, Sanming

    2016-12-01

    To investigate the modulation of the wettability of excipients by different types of surfactants and its impacts on the disintegration of tablets and drug release. The critical micelle concentration (CMC) of surfactants, including sodium dodecyl sulfate (SDS), sodium dodecyl benzene sulfonate (SDBS), dodecyl trimethyl ammonium bromide (DTAB), cetyltrimethyl ammonium bromide (CTAB) and polysorbate (Tween-20 and Tween-80), was obtained using the platinum ring method. Contact angles of surfactant solutions on the excipient compacts and double-distilled water on the mixture of surfactant and the other excipient (magnesium stearate (MgSt) or sodium alginate (SA)) were measured by the sessile drop technique. Besides, surface free energy of excipients was calculated by the Owens method. Finally, the disintegration of tablets and in vitro dissolution testing were performed according to the method described in USP. The wettability of excipients could be enhanced to different extent with low concentration of surfactant solutions and maintained stable basically after CMC. For MgSt (hydrophobic excipient), the shorter the hydrophobic chain (C 12 , including SDS and DTAB), the better the wettability with the addition of surfactant in the formulation, leading to the shorter disintegration time of tablets and higher drug release rate. In contrast, the wettability of SA (hydrophilic excipient) was reduced by adding surfactant, resulting in the longer disintegration time of tablets and lower release rate. The modulation of the wetting of pharmaceutical excipients by surfactant had changed the disintegration time of tablets and drug release rate to a greater extent.

  14. Quantification of Whey Protein Content in Infant Formulas by Sodium Dodecyl Sulfate-Capillary Gel Electrophoresis (SDS-CGE): Single-Laboratory Validation, First Action 2016.15.

    Science.gov (United States)

    Feng, Ping; Fuerer, Christophe; McMahon, Adrienne

    2017-03-01

    Protein separation by sodium dodecyl sulfate-capillary gel electrophoresis, followed by UV absorption at 220 nm, allows for the quantification of major proteins in raw milk. In processed dairy samples such as skim milk powder (SMP) and infant formulas, signals from individual proteins are less resolved, but caseins still migrate as one family between two groups of whey proteins. In the first group, α-lactalbumin and β-lactoglobulin migrate as two distinct peaks. Lactosylated adducts show delayed migration times and interfere with peak separation, but both native and modified forms as well as other low-MW whey proteins still elute before the caseins. The second group contains high-MW whey proteins (including bovine serum albumin, lactoferrin, and immunoglobulins) and elutes after the caseins. Caseins and whey proteins can thus be considered two distinct nonoverlapping families whose ratio can be established based on integrated areas without the need for a calibration curve. Because mass-to-area response factors for whey proteins and caseins are different, an area correction factor was determined from experimental measurement using SMP. Method performance assessed on five infant formulas showed RSDs of 0.2-1.2% (within day) and 0.5-1.1% (multiple days), with average recoveries between 97.4 and 106.4% of added whey protein. Forty-three different infant formulas and milk powders were analyzed. Of the 41 samples with manufacturer claims, the measured whey protein content was in close agreement with declared values, falling within 5% of the declared value in 76% of samples and within 10% in 95% of samples.

  15. Synthesis of 2,4-dinitrophenylhydrazine loaded sodium dodecyl sulfate-coated magnetite nanoparticles for adsorption of Hg(II ions from an aqueous solution

    Directory of Open Access Journals (Sweden)

    Soheil Sobhanardakani

    2016-09-01

    Full Text Available Background: The rapid increase in agricultural and industrial development has made heavy metal pollution a serious environmental problem and public health threat; therefore, removal of heavy metals from water is important. The current study prepared DNPH@SDS@Fe3O4 nanoparticles as a novel and effective adsorbent for removal of Hg(II ions from an aqueous solution. Methods: A selective adsorbent for Hg(II was synthesized by coating Fe3O4 nanoparticles with sodium dodecyl sulfate which was further functionalized with 2,4-dinitrophenylhydrazine (2,4-DNPH. The synthesized nanoparticles were characterized by Fourier transform infrared spectroscopy (FTIR, x-ray diffraction (XRD, scanning electron microscopy (SEM and SEM–EDXSt. The effects of pH, dose of adsorbent and shaking time on adsorption capacity were investigated. The kinetics and equilibrium of adsorption of the metal ions were thoroughly studied. Results: SEM showed that the size of the nanoparticles was 20 to 35 nm. The maximum adsorption capacity for Hg(II was 164.0 mg g-1 for an adsorbent dose of 0.04 g at pH 7.0, 25°C and the initial metal concentration was 25 mg L-1,which was greater than for most adsorbents previously examined for Hg(II adsorption. Adsorption experimental data showed good correlation with the pseudo-secondorder model and Langmuir isotherm model. Conclusion: The results indicated that the DNPH@SDS@Fe3O4 nanoparticles are an efficient adsorbent for removal of heavy metal from wastewater.

  16. Electrophoretic extraction of low molecular weight cationic analytes from sodium dodecyl sulfate containing sample matrices for their direct electrospray ionization mass spectrometry.

    Science.gov (United States)

    Kinde, Tristan F; Lopez, Thomas D; Dutta, Debashis

    2015-03-03

    While the use of sodium dodecyl sulfate (SDS) in separation buffers allows efficient analysis of complex mixtures, its presence in the sample matrix is known to severely interfere with the mass-spectrometric characterization of analyte molecules. In this article, we report a microfluidic device that addresses this analytical challenge by enabling inline electrospray ionization mass spectrometry (ESI-MS) of low molecular weight cationic samples prepared in SDS containing matrices. The functionality of this device relies on the continuous extraction of analyte molecules into an SDS-free solvent stream based on the free-flow zone electrophoresis (FFZE) technique prior to their ESI-MS analysis. The reported extraction was accomplished in our current work in a glass channel with microelectrodes fabricated along its sidewalls to realize the desired electric field. Our experiments show that a key challenge to successfully operating such a device is to suppress the electroosmotically driven fluid circulations generated in its extraction channel that otherwise tend to vigorously mix the liquid streams flowing through this duct. A new coating medium, N-(2-triethoxysilylpropyl) formamide, recently demonstrated by our laboratory to nearly eliminate electroosmotic flow in glass microchannels was employed to address this issue. Applying this surface modifier, we were able to efficiently extract two different peptides, human angiotensin I and MRFA, individually from an SDS containing matrix using the FFZE method and detect them at concentrations down to 3.7 and 6.3 μg/mL, respectively, in samples containing as much as 10 mM SDS. Notice that in addition to greatly reducing the amount of SDS entering the MS instrument, the reported approach allows rapid solvent exchange for facilitating efficient analyte ionization desired in ESI-MS analysis.

  17. Gold nanoparticles-coated poly(3,4-ethylene-dioxythiophene) for the selective determination of sub-nano concentrations of dopamine in presence of sodium dodecyl sulfate

    International Nuclear Information System (INIS)

    Atta, Nada F.; Galal, Ahmed; El-Ads, Ekram H.

    2012-01-01

    For the first time, a novel electrochemical sensor; gold nanoparticles-coated poly(3,4-ethylene-dioxythiophene) polymer modified gold electrode in presence of SDS (Au/PEDOT-Au nano …SDS) was developed by the electrodeposition of gold nanoparticles on poly(3,4-ethylene-dioxythiophene) (PEDOT) modified gold electrode for the selective determination of dopamine (DA) in presence of uric acid (UA) and ascorbic acid (AA) in presence of sodium dodecyl sulfate (SDS). Synergism between the composite of conducting polymer matrix and gold nanoparticles in presence of SDS for electron transfer enhancement of DA is explored. Electrochemical investigation and characterization of the modified electrode are achieved using cyclic voltammetry, electrochemical impedance spectroscopy, scanning electron, and atomic force microscopies. The oxidation current signal of DA is remarkably stable via repeated cycles and has unique long term stability. Very small peak potential separation (ΔE p ), almost zero or 15 mV is also obtained by repeated cycles indicating unusual high reversibility. The use of SDS in the electrochemical determination of DA using linear sweep voltammetry at Au/PEDOT-Au nano modified electrode resulted in determining DA at very low concentrations. The DA concentration could be measured in the linear range of 0.5–20 μmol L −1 and 25–140 μmol L −1 with correlation coefficients of 0.9978, and 0.9987, and detection limits of 0.39 nmol L −1 and 1.55 nmol L −1 , respectively. The validity of using this method in the determination of DA in human urine was also demonstrated. It has been shown that modified electrode can be used as a sensor with high reproducibility, sensitivity, selectivity, and long term stability.

  18. Quality of Iceberg and Romaine lettuce treated by combinations of sanitizer, surfactant, and ultrasound

    Science.gov (United States)

    We report an investigation of the individual and combined effects of sonication, two sanitizers (chlorine and Tsunami 100®) and a surfactant (sodium dodecyl sulfate (SDS) on the quality of fresh-cut Iceberg and Romaine lettuce. Lettuce samples were treated for 1 minute with and without ultrasound in...

  19. A comparison of extracted proteins of isolates of Dermatophilus congolensis by sodium dodecyl sulphate-polyacrylamide gel electrophoresis and Western blotting.

    Science.gov (United States)

    Makinde, A A; Gyles, C L

    1999-07-01

    Antigenic diversity within a collection of 18 isolates of Dermatophilus congolensis from different Continents was examined by sodium dodecyl sulphate-polyacrylamide gel electrophoresis (SDS-PAGE) and by Western blotting with sera from cattle with clinical dermatophilosis using whole cell extracts obtained by three methods and one extract of extracellular products of D. congolensis. One of the methods involving the release of a lysostaphin-solubilized protein (LSP) of whole cells of D. congolensis revealed a number of discrete and easily-identifiable bands in SDS-PAGE which were found suitable for characterizing protein patterns and was, therefore, subsequently used for a comparative analysis of the proteins of all the D. congolensis isolates. Six electropherotypes (ET) of D. congolensis were identified among the 18 isolates using the protein profiles based on the presence of four protein bands at Molecular weights (MW) 62, 28, 17.4 and 16.4 kDa. The ETs were found among isolates from different animal species and from different sources with ET1 consisting of three bovine and two equine isolates; ET2, two bovine and three ovine isolates; ET3, two bovine isolates; ET4, two bovine isolates; ET5, one bovine and one ovine isolates and ET6, two bovine isolates. Immunoblotting of the extracts of D. congolensis isolates with sera from cattle with clinical dermatophilosis infection demonstrated protein bands of MW ranging from 9 kDa to 188 kDa. Sera from chronic dermatophilosis infection demonstrated a 28 kDa protein which was immunodominant in the LSP extracts of all the 18 isolates of D. congolensis tested while sera from mild infections demonstrated mainly the 62 kDa protein in the same extracts. However, many protein bands were demonstrated in surface membrane (TSMP) and extracellular protein extracts with sera from only mildly infected animals. The protein patterns observed in all isolates of D. congolensis revealed global antigenic similarities and distinct differences

  20. Implementation of USP antibody standard for system suitability in capillary electrophoresis sodium dodecyl sulfate (CE-SDS) for release and stability methods.

    Science.gov (United States)

    Esterman, Abbie L; Katiyar, Amit; Krishnamurthy, Girija

    2016-09-05

    Capillary electrophoresis sodium dodecyl sulfate (CE-SDS) is widely used for purity analysis of monoclonal antibody therapeutics for release and stability to demonstrate product consistency and shelf life during the manufacturing and life cycle of the product. CE-SDS method development is focused on exploring the method capability to provide the information about the product purity and product related degradants (fragmentation, aggregation etc.). In order to establish the functionality of the instrumentation, software, and sample preparation; system suitability criteria need to be defined for analytical methods using a well characterized reference standard run under the same protocol and analysis as the test articles. Typically the reference standard is produced using a manufacturing process representative of the clinical material. The qualification, control, and maintenance of in-house reference standards are established through rigorous quality and regulatory guidelines. The U.S. Pharmacopeia (USP) has developed a monoclonal IgG System Suitability Reference Standard to be utilized for assessment of system suitability in CE-SDS methods. In this communication, we evaluate the system suitability acceptance criteria performance of the USP IgG standard using two methods, the recommended USP protocol provided in monograph and a molecule specific Bristol-Myers Squibb (BMS) CE-SDS method. The results from USP IgG standard were compared with two in-house monoclonal antibody reference standards. The data suggest that the USP CE-SDS method may not be suitable for CE-SDS analysis for release and stability of monoclonal antibody therapeutics due to the high level of method induced partial reduction observed for all molecules tested. This high level of fragmentation observed utilizing the USP method will result in reporting lower purity levels, which will impact the overall quality assessment of the molecule. The system suitability criteria recommended by the USP method can be

  1. Reductions of Shiga toxin-producing Escherichia coli and Salmonella typhimurium on beef trim by lactic acid, levulinic acid, and sodium dodecyl sulfate treatments.

    Science.gov (United States)

    Zhao, Tong; Zhao, Ping; Chen, Dong; Jadeja, Ravirajsinh; Hung, Yen-Con; Doyle, Michael P

    2014-04-01

    Studies were done at 21 °C to determine the bactericidal activity of lactic acid, levulinic acid, and sodium dodecyl sulfate (SDS) applied individually and in combination on Shiga toxin-producing Escherichia coli (STEC) in pure culture and to compare the efficacy of lactic acid and levulinic acid plus SDS treatments applied by spray or immersion to inactivate STEC and Salmonella (10(7) CFU/cm2) on beef trim pieces (10 by 10 by 7.5 cm). Application of 3% lactic acid for 2 min to pure cultures was shown to reduce E. coli O26:H11, O45:H2, O111:H8, O103:H2, O121:H2, O145:NM, and O157:H7 populations by 2.1, 0.4, 0.3, 1.4, 0.3, 2.1, and 1.7 log CFU/ml, respectively. Treatment with 0.5% levulinic acid plus 0.05% SDS for 6 log/ml reduction). Beef surface temperature was found to affect the bactericidal activity of treatment with 3 % levulinic acid plus 2% SDS (LV-SDS). Treating cold (4 °C) beef trim with LV-SDS at 21, 62, or 81 °C for 30 s reduced E. coli O157:H7 by 1.0, 1.1, or 1.4 log CFU/cm2, respectively, whereas treating beef trim at 8 °C with LV-SDS at 12 °C for 0.1, 1, 3, or 5 min reduced E. coli O157:H7 by 1.4, 2.4, 2.5, or 3.3 log CFU/cm(2), respectively. Spray treatment of beef trim at 4 °C with 5 % lactic acid only reduced the E. coli O157:H7 population by 1.3 log CFU/cm2. Treating beef trim at 8 °C with LV-SDS for 1, 2, or 3 min reduced Salmonella Typhimurium by 2.1, 2.6, and >5.0 log CFU/cm2, respectively. Hand massaging the treated beef trim substantially reduced contamination of both pathogens, with no detectable E. coli O157:H7 or Salmonella Typhimurium (<5 CFU/cm2) on beef trim pieces treated with LV-SDS. Reduction of E. coli O157:H7 and Salmonella Typhimurium populations was enhanced, but bactericidal activity was affected by the meat temperature.

  2. Rapid discrimination of Gram-positive and Gram-negative bacteria in liquid samples by using NaOH-sodium dodecyl sulfate solution and flow cytometry.

    Directory of Open Access Journals (Sweden)

    Atsushi Wada

    Full Text Available BACKGROUND: For precise diagnosis of urinary tract infections (UTI, and selection of the appropriate prescriptions for their treatment, we explored a simple and rapid method of discriminating gram-positive and gram-negative bacteria in liquid samples. METHODOLOGY/PRINCIPAL FINDINGS: We employed the NaOH-sodium dodecyl sulfate (SDS solution conventionally used for plasmid extraction from Escherichia coli and the automated urine particle analyzer UF-1000i (Sysmex Corporation for our novel method. The NaOH-SDS solution was used to determine differences in the cell wall structures between gram-positive and gram-negative bacteria, since the tolerance to such chemicals reflects the thickness and structural differences of bacterial cell walls. The UF-1000i instrument was used as a quantitative bacterial counter. We found that gram-negative bacteria, including E. coli, in liquid culture could easily be lysed by direct addition of equal volumes of NaOH-SDS solution. In contrast, Enterococcus faecalis, which is a gram-positive bacterium, could not be completely lysed by the solution. We then optimized the reaction time of the NaOH-SDS treatment at room temperature by using 3 gram-positive and 4 gram-negative bacterial strains and determined that the optimum reaction time was 5 min. Finally, in order to evaluate the generalizability of this method, we treated 8 gram-positive strains and 8 gram-negative strains, or 4 gram-positive and 4 gram-negative strains incubated in voluntary urine from healthy volunteers in the same way and demonstrated that all the gram-positive bacteria were discriminated quantitatively from gram negative bacteria using this method. CONCLUSIONS/SIGNIFICANCE: Using our new method, we could easily discriminate gram-positive and gram-negative bacteria in liquid culture media within 10 min. This simple and rapid method may be useful for determining the treatment course of patients with UTIs, especially for those without a prior history

  3. Surfactant-assisted synthesis and characterization of silver nanorods and nanowires by an aqueous solution approach

    Science.gov (United States)

    Zhou, Guangjun; Lü, Mengkai; Yang, Zhongsen; Zhang, Haiping; Zhou, Yuanyuan; Wang, Shumei; Wang, Shufen; Zhang, Aiyu

    2006-03-01

    The silver nanorods and nanowires have been synthesized by a facile aqueous solution process using tri-sodium citrate as reducing agent in the presence of anionic surfactant dodecyl benzene sulfonic acid sodium (DBS). The products were characterized by the techniques of X-ray diffraction (XRD) and transmission electron microscopy (TEM). Experimental results indicated that the concentrations of the reactants AgNO 3 and tri-sodium citrate, in addition to the surfactant DBS should be interdependent in the formation of the silver nanorods and nanowires. The optical properties were investigated and the prepared nanostructures displayed a very strong absorption band at the room temperature.

  4. Inactivation of Escherichia coli O157:H7 in vitro and on the surface of spinach leaves by biobased surfactants

    Science.gov (United States)

    This study was conducted to evaluate the effect of biosurfactants on the populations of Escherichia coli O157:H7 in suspension and on spinach leaves. Eight surfactants including four soybean oil-based biosurfactants, sodium dodecyl sulfate (SDS), polyoxyethylene sorbitan monooleate (Tween 80), sopho...

  5. Study of adjuvant effect of model surfactants from the groups of alkyl sulfates, alkylbenzene sulfonates, alcohol ethoxylates and soaps

    DEFF Research Database (Denmark)

    Clausen, S K; Sobhani, S; Poulsen, O M

    2000-01-01

    The sodium salts of representatives of anionic surfactants, dodecylbenzene sulfonate (SDBS), dodecyl sulfate (SDS) and coconut oil fatty acids, and a nonionic surfactant, dodecyl alcohol ethoxylate, were studied for adjuvant effect on the production of specific IgE antibodies in mice....... The surfactants were injected subcutaneously (sc) in concentrations of 1000, 100, 10 or 1 mg/l, respectively, together with 1 microg of ovalbumin (OVA). In addition, groups of mice received OVA in saline (control group) or in Al(OH)(3) (positive adjuvant control group). After the primary immunization the mice...... that a limited number of surfactants possess an adjuvant effect whereas all surfactants at certain levels can suppress specific IgE production....

  6. Development of a sodium dodecyl sulfate-polyacrylamide gel electrophoresis reference method for the analysis and identification of fish species in raw and heat-processed samples : A collaborative study

    DEFF Research Database (Denmark)

    Pineiro, C.; Barros-Velazquez, J.; Perez-Martin, R.I.

    1999-01-01

    A collaborative study was carried out in seven European labs with the aim of achieving a sodium dodecyl sulfate- polyacrylamide gel electrophoresis (SDS-PAGE) standard operation procedure to identify fish species in raw and cooked samples. Urea and SDS-containing solutions were evaluated...... as extractants. Several preelectrophoretic operations - such as treatment with RNase/DNase, ultrafiltration and desalting - and up to ten types of gels and three SDS-PAGE systems were considered. The SDS-containing solution allowed a higher protein extractability than urea. Unlike urea extraction, SDS extraction...

  7. The impact of nonionic surfactant additives on the nonequilibrium association between oppositely charged polyelectrolytes and ionic surfactants.

    Science.gov (United States)

    Fegyver, Edit; Mészáros, Róbert

    2014-03-28

    The effect of uncharged surfactant additives on the oppositely charged polyion/ionic surfactant complexation is usually described as a direct equilibrium association between the polyelectrolyte molecules and free mixed micelles analogous to the polyion/colloidal particle interactions. This approach predicts that the binding of the ionic surfactant to the polyelectrolyte molecules can be completely suppressed by increasing the nonionic-to-ionic surfactant ratio. In the present work, it is shown that the addition of nonionic surfactants to poly(diallyldimethylammonium chloride)/sodium dodecyl sulfate mixtures considerably enhances the binding of the anionic surfactant to the polycation in the dilute surfactant concentration regime. The dynamic light scattering, turbidity, electrophoretic mobility and fluorescence spectroscopic measurements are consistent with the synergic binding of the ionic and nonionic surfactants to the polyelectrolyte molecules. The enhanced surfactant binding could be utilized for the preparation of stable colloidal dispersions of novel polyion/mixed surfactant nanoparticles over a wide composition range provided that adequate mixing protocols are used. These results clearly indicate that the nonionic surfactant additives can be successfully used to tune the nonequilibrium association of oppositely charged macromolecules and amphiphiles.

  8. Effectiveness of levulinic acid and sodium dodecyl sulfate employed as a sanitizer during harvest or packing of cantaloupes contaminated with Salmonella Poona.

    Science.gov (United States)

    Webb, Cathy C; Erickson, Marilyn C; Davey, Lindsey E; Doyle, Michael P

    2015-08-17

    Freshly harvested Eastern variety cantaloupes (Cucumis melo L. var. reticulatus cv. Athena) were subjected to three different harvest and wash treatments to examine conditions under which the efficacy of the sanitizer, levulinic acid (LV) plus sodium dodecyl sulfate (SDS), could be enhanced to reduce Salmonella contamination. In treatment set one, cantaloupes were spot inoculated with Salmonella enterica serovar Poona (prepared from solid or liquid media cultures) before or after a 1-min dip treatment in LV (2.5, 5.0, 7.5, or 10%) and 2.5% SDS. S. Poona initial populations on rind tissue (4.26-5.04 log CFU/sample) were reduced to detection by enrichment culture when cantaloupes were subsequently exposed to any of the LV/SDS solutions. When S. Poona was introduced after cantaloupes had been dip-treated, greater decreases in pathogen populations at the stem scar were observed when cantaloupes were treated with increasing concentrations of LV. In treatment set two, the response of S. Poona dip-treated with 5% LV/2.5% SDS was compared to a simulated commercial dump tank treatment incorporating 200 ppm chlorine as well as a two-stage treatment employing both the chlorine tank and LV/SDS dip treatments. S. Poona levels (log CFU/sample or # positive by enrichment culture/# analyzed) after treatments were 5.25, 3.07, 7/10, 5/10 (stem scar) and 3.90, 25/40, 28/40, 20/40 (rind) for non-treated, chlorine tank, LV/SDS dip, and tank plus dip treatments, respectively. In treatment set three, freshly harvested cantaloupes were first treated in the field using a needle-free stem scar injection (200 μl, 7.5% LV/1.0% SDS, 60 psi) and a cantaloupe spray (30 ml, 7.5% LV/0.5% SDS). Cantaloupe stem scar and rind tissue were then spot-inoculated with S. Poona using either a liquid or soil-based medium followed by a simulated dump tank treatment incorporating either 200 ppm chlorine or 5% LV/2% SDS. S. Poona inoculated on field-treated cantaloupe rind decreased by 4.7 and 5.31 (liquid

  9. Tuning of nanoparticle-surfactant interactions in aqueous system

    Science.gov (United States)

    Kumar, Sugam; Aswal, V. K.

    2011-01-01

    The interaction of charged (anionic) silica nanoparticles with ionic and nonionic surfactants has been studied using small-angle neutron scattering (SANS). The surfactants used are anionic sodium dodecyl sulfate (SDS), cationic dodecyltrimethyl ammonium bromide (DTAB) and nonionic decaoxyethylene n-dodecylether (C12E10). The measurements are carried out at fixed concentration (1 wt%) of silica nanoparticles and with surfactant concentration varied in the range 0-2 wt%. It is found that there is no direct interaction between the nanoparticles and the surfactant (SDS) when they both are similarly charged. Both the silica nanoparticles and micelles coexist individually with no significant change in the structure of the micelles with respect to that in the pure surfactant solution. On the other hand, the presence of oppositely charged surfactant (DTAB) leads to the aggregation of silica nanoparticles even with very low surfactant concentration. The aggregation of silica nanoparticles is characterized by fractal structure and its fractal dimension remains constant with the increase in the surfactant concentration. In the case of nonionic surfactant, it interacts with the individual silica nanoparticles. The interaction is examined using two models: one that considers the surfactant layer coating on silica nanoparticles and a second one where the surface of the nanoparticles is decorated by the micelles. Contrast variation SANS measurements confirm the uniform decoration of nonionic micelles on the nanoparticles.

  10. Tuning of nanoparticle-surfactant interactions in aqueous system

    International Nuclear Information System (INIS)

    Kumar, Sugam; Aswal, V K

    2011-01-01

    The interaction of charged (anionic) silica nanoparticles with ionic and nonionic surfactants has been studied using small-angle neutron scattering (SANS). The surfactants used are anionic sodium dodecyl sulfate (SDS), cationic dodecyltrimethyl ammonium bromide (DTAB) and nonionic decaoxyethylene n-dodecylether (C 12 E 10 ). The measurements are carried out at fixed concentration (1 wt%) of silica nanoparticles and with surfactant concentration varied in the range 0-2 wt%. It is found that there is no direct interaction between the nanoparticles and the surfactant (SDS) when they both are similarly charged. Both the silica nanoparticles and micelles coexist individually with no significant change in the structure of the micelles with respect to that in the pure surfactant solution. On the other hand, the presence of oppositely charged surfactant (DTAB) leads to the aggregation of silica nanoparticles even with very low surfactant concentration. The aggregation of silica nanoparticles is characterized by fractal structure and its fractal dimension remains constant with the increase in the surfactant concentration. In the case of nonionic surfactant, it interacts with the individual silica nanoparticles. The interaction is examined using two models: one that considers the surfactant layer coating on silica nanoparticles and a second one where the surface of the nanoparticles is decorated by the micelles. Contrast variation SANS measurements confirm the uniform decoration of nonionic micelles on the nanoparticles.

  11. Preparation and characterisation of porous poly(2,5benzimidazole) (ABPBI) membranes using surfactants as templates for polymer electrolyte membrane fuel cells

    CSIR Research Space (South Africa)

    Zheng, H

    2010-04-01

    Full Text Available The first instance synthesis of porous poly(2,5benzimidazole) (ABPBI) membranes using sodium dodecyl sulfate (SDS) surfactants as templates is reported. The membranes were characterised by SEM, TGA, DSC and tensile tests. The tensile test results...

  12. Thermally cleavable surfactants

    Science.gov (United States)

    McElhanon, James R [Manteca, CA; Simmons, Blake A [San Francisco, CA; Zifer, Thomas [Manteca, CA; Jamison, Gregory M [Albuquerque, NM; Loy, Douglas A [Albuquerque, NM; Rahimian, Kamyar [Albuquerque, NM; Long, Timothy M [Urbana, IL; Wheeler, David R [Albuquerque, NM; Staiger, Chad L [Albuquerque, NM

    2006-04-04

    Two new surfactant molecules are reported which contain thermally labile Diels-Alder adducts connecting the polar and non-polar sections of each molecule. The two surfactants possess identical non-polar dodecyl tail segments but exhibit different polar headgroups. The surfactants become soluble in water when anionic salts are formed through the deprotonation of the surfactant headgroups by the addition of potassium hydroxide. When either surfactant is exposed to temperature above about 60.degree. C., the retro Diels-Alder reaction occurs, yielding hydrophilic and hydrophobic fragments and the aqueous solutions of the surfactants subsequently exhibit loss of all surface-active behavior.

  13. Thermally cleavable surfactants

    Science.gov (United States)

    McElhanon, James R [Manteca, CA; Simmons, Blake A [San Francisco, CA; Zifer, Thomas [Manteca, CA; Jamison, Gregory M [Albuquerque, NM; Loy, Douglas A [Albuquerque, NM; Rahimian, Kamyar [Albuquerque, NM; Long, Timothy M [Urbana, IL; Wheeler, David R [Albuquerque, NM; Staiger, Chad L [Albuquerque, NM

    2009-11-24

    Two new surfactant molecules are reported which contain thermally labile Diels-Alder adducts connecting the polar and non-polar sections of each molecule. The two surfactants possess identical non-polar dodecyl tail segments but exhibit different polar headgroups. The surfactants become soluble in water when anionic salts are formed through the deprotonation of the surfactant headgroups by the addition of potassium hydroxide. When either surfactant is exposed to temperature above about 60.degree. C., the retro Diels-Alder reaction occurs, yielding hydrophilic and hydrophobic fragments or the aqueous solutions of the surfactants subsequently exhibit loss of all surface-active behavior.

  14. Effect of three representative surfactants on methane hydrate formation rate and induction time

    Directory of Open Access Journals (Sweden)

    Mostafa keshavarz Moraveji

    2017-06-01

    Full Text Available The effects of three types of surfactants on methane hydrate formation process were investigated. Three different classes of surfactants involving anionic (sodium dodecyl sulfonate, cationic (hexadecyl trimethyl ammonium bromide and non-ionic (poly oxy ethylene (40 octyl phenyl ether have been used. Thermodynamics of hydrate formation, formation rate, kinetic constants and induction time in the presence of surfactants with various concentrations were analyzed. Critical micelle concentrations (CMCs of these surfactants in water were determined by induction time measurements in various concentrations under methane hydrate formation conditions. The critical micelle concentration (CMC at the methane hydrate formation conditions for SDS, HTABr and TritonX-405 solutions were obtained at 450, 380 and 950 ppm, respectively. The experimental results indicated that hydrate formation rate increased with the use of surfactants for all concentrations and induction time decreased. It was found that for surfactants, CMC at hydrate formation conditions was less than CMC at ambient conditions.

  15. Estudo das dispersões aquosas de nanotubos de carbono utilizando diferentes surfactantes Study of aqueous dispersions of carbon nanotubes using different surfactants

    Directory of Open Access Journals (Sweden)

    Isabella R. da Silva

    2013-01-01

    Full Text Available The dispersion of carbon nanotubes in water for their utilization in nanoscale devices is a challenging task. Comparative studies on interaction and dispersion of multi-wall carbon nanotubes (MWNT using two different surfactants (sodium dodecyl sulfate, SDS, and polyoxyethylenesorbitanmonooleate, Tween 80 are presented. The interaction between carbon nanotubes and surfactants was studied by tensiometry, conductivimetry, and fluorimetry. The dispersions of MWNT in surfactants were characterized using a UV-vis spectrophotometer. For effective dispersion, the minimum weight ratio of MWNT to surfactant was 1:41 and 1:3 for SDS and Tween 80, respectively.

  16. Tunable, antibacterial activity of silicone polyether surfactants.

    Science.gov (United States)

    Khan, Madiha F; Zepeda-Velazquez, Laura; Brook, Michael A

    2015-08-01

    Silicone surfactants are used in a variety of applications, however, limited data is available on the relationship between surfactant structure and biological activity. A series of seven nonionic, silicone polyether surfactants with known structures was tested for in vitro antibacterial activity against Escherichia coli BL21. The compounds varied in their hydrophobic head, comprised of branched silicone structures with 3-10 siloxane linkages and, in two cases, phenyl substitution, and hydrophilic tail of 8-44 poly(ethylene glycol) units. The surfactants were tested at three concentrations: below, at, and above their Critical Micelle Concentrations (CMC) against 5 concentrations of E. coli BL21 in a three-step assay comprised of a 14-24h turbidometric screen, a live-dead stain and viable colony counts. The bacterial concentration had little effect on antibacterial activity. For most of the surfactants, antibacterial activity was higher at concentrations above the CMC. Surfactants with smaller silicone head groups had as much as 4 times the bioactivity of surfactants with larger groups, with the smallest hydrophobe exhibiting potency equivalent to sodium dodecyl sulfate (SDS). Smaller PEG chains were similarly associated with higher potency. These data link lower micelle stability and enhanced permeability of smaller silicone head groups to antibacterial activity. The results demonstrate that simple manipulation of nonionic silicone polyether structure leads to significant changes in antibacterial activity. Copyright © 2015 Elsevier B.V. All rights reserved.

  17. Interactions between dodecyl phosphates and hydroxyapatite or tooth enamel: relevance to inhibition of dental erosion.

    Science.gov (United States)

    Jones, Siân B; Barbour, Michele E; Shellis, R Peter; Rees, Gareth D

    2014-05-01

    Tooth surface modification is a potential method of preventing dental erosion, a form of excessive tooth wear facilitated by softening of tooth surfaces through the direct action of acids, mainly of dietary origin. We have previously shown that dodecyl phosphates (DPs) effectively inhibit dissolution of native surfaces of hydroxyapatite (the type mineral for dental enamel) and show good substantivity. However, adsorbed saliva also inhibits dissolution and DPs did not augment this effect, which suggests that DPs and saliva interact at the hydroxyapatite surface. In the present study the adsorption and desorption of potassium and sodium dodecyl phosphates or sodium dodecyl sulphate (SDS) to hydroxyapatite and human tooth enamel powder, both native and pre-treated with saliva, were studied by high performance liquid chromatography-mass Spectrometry. Thermo gravimetric analysis was used to analyse residual saliva and surfactant on the substrates. Both DPs showed a higher affinity than SDS for both hydroxyapatite and enamel, and little DP was desorbed by washing with water. SDS was readily desorbed from hydroxyapatite, suggesting that the phosphate head group is essential for strong binding to this substrate. However, SDS was not desorbed from enamel, so that this substrate has surface properties different from those of hydroxyapatite. The presence of a salivary coating had little or no effect on adsorption of the DPs, but treatment with DPs partly desorbed saliva; this could account for the failure of DPs to increase the dissolution inhibition due to adsorbed saliva. Copyright © 2014 Elsevier B.V. All rights reserved.

  18. Performance improvement of ionic surfactant flooding in carbonate rock samples by use of nanoparticles

    Directory of Open Access Journals (Sweden)

    Mohammad Ali Ahmadi

    2016-07-01

    Full Text Available Abstract Various surfactants have been used in upstream petroleum processes like chemical flooding. Ultimately, the performance of these surfactants depends on their ability to reduce the interfacial tension between oil and water. The surfactant concentration in the aqueous solution decreases owing to the loss of the surfactant on the rock surface in the injection process. The main objective of this paper is to inhibit the surfactant loss by means of adding nanoparticles. Sodium dodecyl sulfate and silica nanoparticles were used as ionic surfactant and nanoparticles in our experiments, respectively. AEROSIL® 816 and AEROSIL® 200 are hydrophobic and hydrophilic nanoparticles. To determine the adsorption loss of the surfactant onto rock samples, a conductivity approach was used. Real carbonate rock samples were used as the solid phase in adsorption experiments. It should be noted that the rock samples were water wet. This paper describes how equilibrium adsorption was investigated by examining adsorption behavior in a system of carbonate sample (solid phase and surfactant solution (aqueous phase. The initial surfactant and nanoparticle concentrations were 500–5000 and 500–2000 ppm, respectively. The rate of surfactant losses was extremely dependent on the concentration of the surfactant in the system, and the adsorption of the surfactant decreased with an increase in the nanoparticle concentration. Also, the hydrophilic nanoparticles are more effective than the hydrophobic nanoparticles.

  19. Small-angle neutron scattering study of structure and interaction of nanoparticle, protein, and surfactant complexes.

    Science.gov (United States)

    Mehan, Sumit; Chinchalikar, Akshay J; Kumar, Sugam; Aswal, Vinod K; Schweins, Ralf

    2013-09-10

    Small-angle neutron scattering (SANS) measurements have been carried out from the multicomponent system composed of Ludox HS40 silica nanoparticle, bovine serum albumin (BSA) protein, and sodium dodecyl sulfate (SDS) surfactant in an aqueous system under the solution condition that all the components are negatively charged. Although the components are similarly charged, strong structural evolutions among them have been observed. The complexes of different components in pairs (nanoparticle-protein, nanoparticle-surfactant, and protein-surfactant) have been examined to correlate the role of each component in the three-component nanoparticle-protein-surfactant system. The nanoparticle-protein system shows depletion interaction induced aggregation of nanoparticles in the presence of protein. Both nanoparticle and surfactant coexist individually in a nanoparticle-surfactant system. In the case of a protein-surfactant system, the cooperative binding of surfactant with protein leads to micelle-like clusters of surfactant formed along the unfolded protein chain. The structure of the three-component (nanoparticle-protein-surfactant) system is found to be governed by the synergetic effect of nanoparticle-protein and protein-surfactant interactions. The nanoparticle aggregates coexist with the structures of protein-surfactant complex in the three-component system. The nanoparticle aggregation as well as unfolding of protein is enhanced in this system as compared to the corresponding two-component systems.

  20. Surfactant loss control in chemical flooding spectroscopic and calorimetric study of adsorption and precipitation on reservoir minerals. Annual report, September 30, 1993--September 30, 1994

    Energy Technology Data Exchange (ETDEWEB)

    Somasundaran, P.

    1995-06-01

    The aim of this project is to elucidate the mechanisms underlying adsorption and surface precipitation of flooding surfactants on reservoir minerals. Effect of surfactant structure, surfactant combinations, other inorganic and polymeric species is being studied. A multi-pronged approach consisting of micro and nano spectroscopy, microcalorimetry, electrokinetics, surface tension and wettability is used to achieve the goals. The results of this study should help in controlling surfactant loss in chemical flooding and also in developing optimum structures and conditions for efficient chemical flooding processes. During the second year of this three year contract, adsorption/desorption of single surfactants and select surfactant mixtures on alumina and silica was studied. Surfactants studied include the anionic sodium dodecyl sulfate (SDS), cationic tetradecyl trimethyl ammonium chloride (TTAC), nonionic pentadecylethoxylated nonyl phenol (NP-15) and the nonionic octaethylene glycol n-dodecyl ether (C{sub 12}EO{sub 8}) of varying hydrocarbon chain length. The microstructure of the adsorbed layer in terms of micropolarity and aggregation numbers was probed using fluorescence spectroscopy. Changes of microstructure upon dilution (desorption) were also studied. Presence of the nonionic surfactant in the mixed aggregate led to shielding of the charge of the ionic surfactant which in-turn promoted aggregation but reduced electrostatic attraction between the charged surfactant and the mineral surface. Strong consequences of surfactant interactions in solution upon adsorption as well as correlations between monomer concentrations in mixtures and adsorption were revealed.

  1. Integration of chemical scrubber with sodium hypochlorite and surfactant for removal of hydrocarbons in cooking oil fume

    International Nuclear Information System (INIS)

    Cheng, Hsin-Han; Hsieh, Chu-Chin

    2010-01-01

    There are many types of technologies to control cooking oil fumes (COFs), but current typical technologies, such as electrostatic precipitator, conventional scrubber, catalyst, or condenser, are unable to efficiently remove the odorous materials present in COFs which are the primary cause of odor-complaint cases. There is also a lack of information about using sodium hypochlorite (NaOCl) and surfactants to remove contaminants in COFs, and previous studies lack on-site investigations in restaurants. This study presents a chemical scrubber integrated with an automatic control system (ACS) to treat hydrocarbons (HCs) in COFs, and to monitor non-methane HCs (NMHC) and odor as indicators for its efficiency evaluation. The chemical scrubber effectively treats hydrophobic substances in COFs by combining surfactant and NaOCl under optimal operational conditions with NHMC removal efficiency as high as 85%. The mass transfer coefficient (K L a) of NMHC was enhanced by 50% under the NaOCl and surfactant conditions, as compared to typical wet scrubber. Further, this study establishes the fuzzy equations of the ACS, including the relationship between the removal efficiency and K L a, liquid/gas ratio, pH and C NaOCl .

  2. Preparation and physicochemical properties of surfactant-free emulsions using electrolytic-reduction ion water containing lithium magnesium sodium silicate.

    Science.gov (United States)

    Okajima, Masahiro; Wada, Yuko; Hosoya, Takashi; Hino, Fumio; Kitahara, Yoshiyasu; Shimokawa, Ken-ichi; Ishii, Fumiyoshi

    2013-04-01

    Surfactant-free emulsions by adding jojoba oil, squalane, olive oil, or glyceryl trioctanoate (medium chain fatty acid triglycerides, MCT) to electrolytic-reduction ion water containing lithium magnesium sodium silicate (GE-100) were prepared, and their physiochemical properties (thixotropy, zeta potential, and mean particle diameter) were evaluated. At an oil concentration of 10%, the zeta potential was ‒22.3 ‒ ‒26.8 mV, showing no marked differences among the emulsions of various types of oil, but the mean particle diameters in the olive oil emulsion (327 nm) and MCT emulsion (295 nm) were smaller than those in the other oil emulsions (452-471 nm). In addition, measurement of the hysteresis loop area of each type of emulsion revealed extremely high thixotropy of the emulsion containing MCT at a low concentration and the olive emulsion. Based on these results, since surfactants and antiseptic agents markedly damage sensitive skin tissue such as that with atopic dermatitis, surfactant- and antiseptic-free emulsions are expected to be new bases for drugs for external use.

  3. Mobilization of arsenic from contaminated sediment by anionic and nonionic surfactants.

    Science.gov (United States)

    Liang, Chuan; Peng, Xianjia

    2017-06-01

    The increasing manufacture of surfactants and their wide application in industry, agriculture and household detergents have resulted in large amounts of surfactant residuals being discharged into water and distributed into sediment. Surfactants have the potential to enhance arsenic mobility, leading to risks to the environment and even human beings. In this study, batch and column experiments were conducted to investigate arsenic mobilization from contaminated sediment by the commercial anionic surfactants sodium dodecylbenzenesulfonate (SDBS), sodium dodecyl sulfate (SDS), sodium laureth sulfate (AES) and nonionic surfactants phenyl-polyethylene glycol (Triton X-100) and polyethylene glycol sorbitan monooleate (Tween-80). The ability of surfactants to mobilize arsenic followed the order AES>SDBS>SDS≈Triton X-100>Tween 80. Arsenic mobilization by AES and Triton X-100 increased greatly with the increase of surfactant concentration and pH, while arsenic release by SDBS, SDS and Tween-80 slightly increased. The divalent ion Ca 2+ caused greater reduction of arsenic mobilization than Na + . Sequential extraction experiments showed that the main fraction of arsenic mobilized was the specifically adsorbed fraction. Solid phase extraction showed that arsenate (As(V)) was the main species mobilized by surfactants, accounting for 65.05%-77.68% of the total mobilized arsenic. The mobilization of arsenic was positively correlated with the mobilization of iron species. The main fraction of mobilized arsenic was the dissolved fraction, accounting for 70% of total mobilized arsenic. Copyright © 2016. Published by Elsevier B.V.

  4. LINEAR SOLVATION ENERGY RELATIONSHIPS FOR CHARACTERIZATION OF MLC SYSTEMS WITH SODIUM DODECYL SULPHATE MOBILE PHASES MODIFIED BY ALIPHATIC ALCOHOLS OR CARBOXYLIC ACIDS

    NARCIS (Netherlands)

    Markov, Vadym V.; Boichenko, Alexander P.; Loginova, Lidia P.

    2012-01-01

    The Linear Solvation Energy Relationships (LSER) have been successfully used for the modeling of partition and retention of the set of test compounds in different systems. The properties of micellar chromatographic systems with the mobile phases on the basis of sodium dodecylsulphate modified (ODS)

  5. Interactions of short chain phenylalkanoic acids within ionic surfactant micelles in aqueous media

    Directory of Open Access Journals (Sweden)

    Naeem Kashif

    2012-01-01

    Full Text Available % SDS KR nema Solubilization and interactions of phenylalkanoic acids induced by cationic surfactant, cetyltrimethylammonium bromide (CTAB and an anionic surfactant, sodium dodecyl sulfate (SDS was investigated spectrophotometrically at 25.0°C. The UV spectra of the additives (acids were measured with and without surfactant above and below critical micelle concentration (cmc of the surfactant. The presence of alkyl chain in phenylalkanoic acids is responsible for hydrophobic interaction resulting in shift of the spectra towards longer wavelength (red shift. The value of partition coefficient (Kx between the bulk water and surfactant micelles and in turn standard free energy change of solubilization (ΔGpº were also estimated by measuring the differential absorbance (ΔA of the additives in micellar solutions.

  6. How chain length and charge affect surfactant denaturation of acyl coenzyme a binding protein (ACBP)

    DEFF Research Database (Denmark)

    Andersen, Kell; Otzen, Daniel

    2009-01-01

    Using intrinsic tryptophan fluorescence, equilibria and kinetics of unfolding of acyl coenzyme A binding protein (ACBP) have been investigated in sodium alkyl sulfate surfactants of different chain length (8-16 carbon atoms) and with different proportions of the nonionic surfactant dodecyl...... maltoside (DDM). The aim has been to determine how surfactant chain length and micellar charge affect the denaturation mechanism. ACBP denatures in two steps irrespective of surfactant chain length, but with increasing chain length, the potency of the denaturant rises more rapidly than the critical micelle...... constants increases linearly with denaturant concentration below the cmc but declines at higher concentrations. Both shortening chain length and decreasing micellar charge reduce the overall kinetics of unfolding and makes the dependence of unfolding rate constants on surfactant concentration more complex...

  7. The effect of surfactants on the electropolishing behavior of copper in orthophosphoric acid

    Energy Technology Data Exchange (ETDEWEB)

    Taha, A.A., E-mail: asia_taha@yahoo.com; Ahmed, A.M.; Rahman, H.H. Abdel; Abouzeid, F.M.

    2013-07-15

    The electropolishing behavior of copper was studied in orthophosphoric acid with Triton X-100, sodium dodecyl sulphate and cetyl pyridinium chloride as additives for improving the finish obtained on copper surface. This was investigated by measuring and comparing anode potential-limiting current relationships in solutions of gradually increasing concentration of surfactants. The addition of surfactants to the electropolishing solution results in a lower limiting current. This confirms the mass transport of dissolved species from the anode surface to the bulk of solution as the rate-determining step in the presence of three surfactants in all concentrations investigated. Scanning electron microscope (SEM), atomic force microscope (AFM) and measured brightness values were used to investigate the copper surface after electropolishing and the results were compared to polishing done in absence of surfactants. According to SEM images and brightness values, addition of Triton X-100 was effective to enhance levelling and brightening more than sodium dodecyl sulphate and cetyl pyridinium chloride. AFM analysis showed that the roughness values (R{sub a}) for an electropolished copper surface, in presence of surfactants, is significantly lower than in absence of surfactants. Different reaction conditions and the physical properties of solutions are studied to obtain dimensionless correlation among all these parameters.

  8. Use of anionic surfactants for selective polishing of silicon dioxide over silicon nitride films using colloidal silica-based slurries

    Science.gov (United States)

    Penta, Naresh K.; Amanapu, H. P.; Peethala, B. C.; Babu, S. V.

    2013-10-01

    Four different anionic surfactants, sodium dodecyl sulfate, dodecyl benzene sulfonic acid (DBSA), dodecyl phosphate and Sodium lauroyl sarcosine, selected from the sulfate, phosphate, and carboxylic family, were investigated as additives in silica dispersions for selective polishing of silicon dioxide over silicon nitride films. We found that all these anionic surfactants suppress the nitride removal rates (RR) for pH ≤4 while more or less maintaining the oxide RRs, resulting in high oxide-to-nitride RR selectivity. The RR data obtained as a function of pH were explained based on pH dependent distributions of surfactant species, change in the zeta potentials of oxide and nitride surfaces, and thermogravimetric data. It appears that the negatively charged surfactant species preferentially adsorb on the positively charged nitride surface below IEP through its electrostatic interactions and form a bilayer adsorption, resulting in the suppression of nitride RRs. In contrast to the surfactants, K2SO4 interacts only weakly with the nitride surface and hence cannot suppress its RR.

  9. Physicochemical, morphological and cellular uptake properties of lutein nanodispersions prepared by using surfactants with different stabilizing mechanisms.

    Science.gov (United States)

    Tan, Tai Boon; Chu, Wern Cui; Yussof, Nor Shariffa; Abas, Faridah; Mirhosseini, Hamed; Cheah, Yoke Kqueen; Nehdi, Imededdine Arbi; Tan, Chin Ping

    2016-04-01

    In this study, we prepared a series of lutein nanodispersions via the solvent displacement method, by using surfactants with different stabilizing mechanisms. The surfactants used include Tween 80 (steric stabilization), sodium dodecyl sulfate (SDS; electrostatic stabilization), sodium caseinate (electrosteric stabilization) and SDS-Tween 80 (electrostatic-steric stabilization). We then characterized the resulting lutein nanodispersions in terms of their particle size, particle size distribution, zeta potential, lutein content, flow behavior, apparent viscosity, transmittance, color, morphological properties and their effects on cell viability and cellular uptake. The type of surfactant used significantly (p lutein content) remained unaffected. Transmission electron microscopy (TEM) images obtained from this study demonstrated that the solvent displacement method was capable of producing lutein nanodispersions containing spherical particles with sizes ranging from 66.20-125.25 nm, depending on the type of surfactant used. SDS and SDS-Tween 80 surfactants negatively affected the viability of the HT-29 cells used in this study. Thus, for the cellular uptake determination, only Tween 80 and sodium caseinate surfactants were used. The cellular uptake of the lutein nanodispersion stabilized by sodium caseinate was higher than that which was stabilized by Tween 80. All things considered, the type of surfactant with different stabilizing mechanisms did produce lutein nanodispersions with different characteristics. These findings would aid in future selection of surfactants in order to produce nanodispersions with desirable properties.

  10. NMR study of the dynamics of cationic gemini surfactant 14-2-14 in mixed solutions with conventional surfactants.

    Science.gov (United States)

    Jiang, Yan; Lu, Xing-Yu; Chen, Hong; Mao, Shi-Zhen; Liu, Mai-Li; Luo, Ping-Ya; Du, You-Ru

    2009-06-18

    Three kinds of conventional surfactants, namely, two nonionic surfactants [polyethylene glycol (23) lauryl ether (Brij-35) and Triton X-100 (TX-100)], one cationic surfactant [n-tetradecyltrimethyl ammonium bromide (TTAB)], and an anionic surfactant [sodium n-dodecyl sulfate (SDS)}, were mixed into the quaternary ammonium gemini surfactant [C(14)H(29)N(+)(CH(3))(2)](2)(CH(2))(2).2Br(-) (14-2-14) in aqueous solution. The exchange rate constants between 14-2-14 molecules in the mixed micelles and those in the bulk solution were detected using two nuclear magnetic resonance (NMR) methods: one-dimensional (1D) line shape analysis and two-dimensional (2D) exchange spectroscopy (EXSY). The results obtained from these two methods were consistent. Both showed that mixing a nonionic conventional surfactant, either Brij-35 or TX-100, enhanced the exchange process between the 14-2-14 molecules in the mixed micelles and those in the bulk solution. In contrast, the anionic surfactant SDS and the cationic surfactant TTAB slowed the process slightly.

  11. Polyelectrolyte-surfactant complexes of poly[3,5-bis(dimethylaminomethyl)-4-hydroxystyrene]-block-poly(ethylene oxide) and sodium dodecyl sulfate: anomalous self-assembly behavior

    Czech Academy of Sciences Publication Activity Database

    Hajduová, J.; Procházka, K.; Šlouf, Miroslav; Angelov, Borislav; Mountrichas, G.; Pispas, S.; Štěpánek, M.

    2013-01-01

    Roč. 29, č. 18 (2013), s. 5443-5449 ISSN 0743-7463 R&D Projects: GA TA ČR TE01020118; GA ČR(CZ) GA13-02938S Institutional support: RVO:61389013 Keywords : polymer self-assemblies * light and X-ray scattering * electron microsocopy Subject RIV: JA - Electronics ; Optoelectronics, Electrical Engineering Impact factor: 4.384, year: 2013

  12. Effect of ethyleneoxide groups of anionic surfactants on lipase activity.

    Science.gov (United States)

    Magalhães, Solange S; Alves, Luís; Sebastião, Marco; Medronho, Bruno; Almeida, Zaida L; Faria, Tiago Q; Brito, Rui M M; Moreno, Maria J; Antunes, Filipe E

    2016-09-01

    The use of enzymes in laundry and dish detergent products is growing. Such tendency implies dedicated studies to understand surfactant-enzyme interactions. The interactions between surfactants and enzymes and their impact on the catalytic efficiency represent a central problem and were here evaluated using circular dichroism, dynamic light scattering, and enzyme activity determinations. This work focuses on this key issue by evaluating the role of the ethyleneoxide (EO) groups of anionic surfactants on the structure and activity of a commercial lipase, and by focusing on the protein/surfactant interactions at a molecular level. The conformational changes and enzymatic activity of the protein were evaluated in the presence of sodium dodecyl sulfate (SDS also denoted as SLE 0 S) and of sodium lauryl ether sulfate with two EO units (SLE 2 S). The results strongly suggest that the presence of EO units in the surfactant polar headgroup determines the stability and the activity of the enzyme. While SDS promotes enzyme denaturation and consequent loss of activity, SLE 2 S preserves the enzyme structure and activity. The data further highlights that the electrostatic interactions among the protein groups are changed by the presence of the adsorbed anionic surfactants being such absorption mainly driven by hydrophobic interactions. © 2016 American Institute of Chemical Engineers Biotechnol. Prog., 32:1276-1282, 2016. © 2016 American Institute of Chemical Engineers.

  13. Influences of surfactants on the preparation of copper nanoparticles by electron beam irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Zhou Ruimin [Shanghai Applied Radiation Institute, Shanghai University, Shanghai 201800 (China)], E-mail: zhourm47@staff.shu.edu.cn; Wu Xinfeng; Hao Xufeng; Zhou Fei [Shanghai Applied Radiation Institute, Shanghai University, Shanghai 201800 (China); Li Hongbin [Department of Chemical Engineering and Technology, Shanghai University, Shanghai 201800 (China); Rao Weihong [Shenzhen Tianding Fine Chemical Engineering Manufacturing Co., Ltd., Shenzhen, Guangdong 518057 (China)

    2008-02-15

    Electron beam radiation was applied to prepare nano-size copper in water system using polyvinyl alcohol, sodium dodecyl benzene sulfonate, gluten and polyethylene glycol as the surfactants, respectively. The irradiated products were characterized by XRD, TEM and LSPSDA. The XRD and TEM showed that relative pure copper products with an average size of 20 nm, 40 nm and 20 nm can be obtained by using gluten, PEG and SDBS as surfactant, respectively. An admixture of copper and cuprous oxide was obtained in PVA system. The LSPSDA showed that the size of the Cu nanoparticles decreased with increasing the glutin concentration.

  14. Direct Observation Of Nanoparticle-Surfactant Interactions Using Small Angle Neutron Scattering

    Science.gov (United States)

    Kumar, Sugam; Aswal, V. K.

    2010-12-01

    Interactions of anionic silica nanoparticles with anionic, cationic and nonionic surfactants have directly been studied by contrast variation small angle neutron scattering (SANS). The measurements are performed on 1 wt% of both silica nanoparticles and surfactants of anionic sodium dodecyle sulphate (SDS), cationic dodecyltrimethyl ammonium bromide (DTAB) and non-ionic polyoxyethylene 10 lauryl ether (C12E10) in aqueous solution. We show that there is no direct interaction in the case of SDS with silica particles, whereas strong interaction for DTAB leads to the aggregation of silica particles. The interaction of C12E10 is found through the micelles adsorbed on the silica particles.

  15. Foaming behaviour of polymer-surfactant solutions

    International Nuclear Information System (INIS)

    Cervantes-MartInez, Alfredo; Maldonado, Amir

    2007-01-01

    We study the effect of a non-ionic amphiphilic polymer (PEG-100 stearate also called Myrj 59) on the foaming behaviour of aqueous solutions of an anionic surfactant (sodium dodecyl sulfate or SDS). The SDS concentration was kept fixed while the Myrj 59 concentration was varied. Measurements of foamability, surface tension and electrical conductivity were carried out. The results show two opposite effects depending on the polymer concentration: foamability is higher when the Myrj 59 concentration is low; however, it decreases considerably when the polymer concentration is increased. This behaviour is due to the polymer adsorption at the air/liquid interface at lower polymer concentrations, and to the formation of a polymer-surfactant complex in the bulk at higher concentrations. The results are confirmed by surface tension and electrical conductivity measurements, which are interpreted in terms of the microstructure of the polymer-surfactant solutions. The observed behaviour is due to the amphiphilic nature of the studied polymer. The increased hydrophobicity of Myrj 59, compared to that of water-soluble polymers like PEG or PEO, increases its 'reactivity' towards SDS, i.e. the strength of its interaction with this anionic surfactant. Our results show that hydrophobically modified polymers have potential applications as additives in order to control the foaming properties of surfactant solutions

  16. Syntheses of surfactants from oleochemical epoxides

    Directory of Open Access Journals (Sweden)

    Warwel Siegfried

    2001-01-01

    Full Text Available Sugar-based surfactants were obtained in good yields (up to 100% under mild conditions (70°C, methanol or mixtures of methanol and water by ring-opening of terminal epoxides with aminopolyols, derived from glucose. Reaction of N-methyl glucamine with epoxides from even-numbered C4-C18 alpha-olefins or from terminal unsaturated fatty acid methyl esters leads to linear products, while corresponding reactions with N-dodecyl glucamine or glucamine yield surfactants with different Y-structures. Products obtained by conversion of omega-epoxy fatty acid methyl esters were saponificated with NaOH or hydrolyzed enzymatically to sodium salts or free acids respectively, which are amphoteric surfactants. Studies of the surfactants at different pH-values demonstrate different surface active properties in aqueous solutions. Critical micelle concentrations (c.m.c. in a range between 2 and 500mg/l and surface tensions of 25-40mN/m were measured for several of the synthesized sugar-based surfactants. The ring-opening products are rather poor foamers, whereas some of the corresponding hydrobromides show good foaming properties.

  17. Effect of surfactants on the spectrofluorimetric properties of zearalenone

    International Nuclear Information System (INIS)

    Appell, Michael; Bosma, Wayne B.

    2011-01-01

    The chemiluminescent properties of the estrogenic mycotoxin zearalenone in the presence of aqueous micellar media were investigated using steady state fluorescence techniques. Micelles of surfactants sodium dodecyl sulfate (SDS), hexadecyltrimethylammonium bromide (CTAB), and non-ionic Triton X-100 enhanced the fluorescence intensity of zearalenone in aqueous solutions. The binding constants have been determined and indicate zearalenone has the highest affinity for Triton X-100, followed by CTAB, and then by SDS. The encapsulation of zearalenone by the micelles studied is spontaneous and exothermic. The selective microenvironments provided by organized micellar systems offer an attractive medium to modulate fluorescence detection of zearalenone. - Highlights: → Surfactants can selectively modulate the fluorescence detection of zearalenone. → Binding studies provide information on the zearalenone-surfactant interactions. → Fluorescence intensity of zearalenone is related to the micelle microenvironment.

  18. Tuning of depletion interaction in nanoparticle-surfactant systems

    International Nuclear Information System (INIS)

    Ray, D.; Aswal, V. K.

    2014-01-01

    The interaction of anionic silica nanoparticles (Ludox LS30) and non-ionic surfactants decaethylene glycol monododecylether (C12E10) without and with anionic sodium dodecyl sulfate (SDS) in aqueous electrolyte solution has been studied by small-angle neutron scattering (SANS). The measurements have been carried out for fixed concentrations of nanoparticle (1 wt%), surfactants (1 wt%) and electrolyte (0.1 M NaCl). Each of these nanoparticlesurfactant systems has been examined for different contrast conditions where individual components (nanoparticle or surfactant) are made visible. It is observed that the nanoparticle-C12E10 system leads to the depletion-induced aggregation of nanoparticles. The system however behaves very differently on addition of SDS where depletion interaction gets suppressed and aggregation of nanoparticles can be prevented. We show that C12E10 and SDS form mixed micelles and the charge on these micelles plays important role in tuning the depletion interaction

  19. Tuning of depletion interaction in nanoparticle-surfactant systems

    Energy Technology Data Exchange (ETDEWEB)

    Ray, D., E-mail: debes@barc.gov.in; Aswal, V. K., E-mail: debes@barc.gov.in [Solid State Physics Division, Bhabha Atomic Research Centre, Mumbai-400085 (India)

    2014-04-24

    The interaction of anionic silica nanoparticles (Ludox LS30) and non-ionic surfactants decaethylene glycol monododecylether (C12E10) without and with anionic sodium dodecyl sulfate (SDS) in aqueous electrolyte solution has been studied by small-angle neutron scattering (SANS). The measurements have been carried out for fixed concentrations of nanoparticle (1 wt%), surfactants (1 wt%) and electrolyte (0.1 M NaCl). Each of these nanoparticlesurfactant systems has been examined for different contrast conditions where individual components (nanoparticle or surfactant) are made visible. It is observed that the nanoparticle-C12E10 system leads to the depletion-induced aggregation of nanoparticles. The system however behaves very differently on addition of SDS where depletion interaction gets suppressed and aggregation of nanoparticles can be prevented. We show that C12E10 and SDS form mixed micelles and the charge on these micelles plays important role in tuning the depletion interaction.

  20. Tuning of depletion interaction in nanoparticle-surfactant systems

    Science.gov (United States)

    Ray, D.; Aswal, V. K.

    2014-04-01

    The interaction of anionic silica nanoparticles (Ludox LS30) and non-ionic surfactants decaethylene glycol monododecylether (C12E10) without and with anionic sodium dodecyl sulfate (SDS) in aqueous electrolyte solution has been studied by small-angle neutron scattering (SANS). The measurements have been carried out for fixed concentrations of nanoparticle (1 wt%), surfactants (1 wt%) and electrolyte (0.1 M NaCl). Each of these nanoparticlesurfactant systems has been examined for different contrast conditions where individual components (nanoparticle or surfactant) are made visible. It is observed that the nanoparticle-C12E10 system leads to the depletion-induced aggregation of nanoparticles. The system however behaves very differently on addition of SDS where depletion interaction gets suppressed and aggregation of nanoparticles can be prevented. We show that C12E10 and SDS form mixed micelles and the charge on these micelles plays important role in tuning the depletion interaction.

  1. Surfactants enhance recovery of poorly soluble drugs during microdialysis sampling

    DEFF Research Database (Denmark)

    Koplin, Sebastian; Kumpugdee-Vollrath, Mont; Bauer-Brandl, Annette

    2017-01-01

    Aim of this project was to investigate the applicability of a recently developed in vitro microdialysis-sampling approach in connection with a dissolution-/permeation (D/P) system, especially the impact of surfactants within the perfusion fluid. The D/P-system is based on side-by-side chambers...... drug-dissolution (-release) and drug permeation. Furthermore, it should allow quantification of the unbound (free) drug concentration. In the first step, it was assessed, if the addition of the anionic surfactant sodium dodecyl sulphate (SDS) to the perfusate of the microdialysis system affects...... celecoxib, i.e. the fraction of drug, which is not associated with taurocholate surfactant micelles. In buffer, the measured concentrations matched the overall CXB concentrations. By the use of SDS-containing perfusates microdialysis sampling enabled reliable quantification of minute amounts of free CXB...

  2. Sodium dodecyl sulfate (SDS) effect on the thermal stability of oxy-HbGp: dynamic light scattering (DLS) and small angle X-ray scattering (SAXS) studies.

    Science.gov (United States)

    Carvalho, José Wilson P; Alves, Fernanda Rosa; Batista, Tatiana; Carvalho, Francisco Adriano O; Santiago, Patrícia S; Tabak, Marcel

    2013-11-01

    Glossoscolex paulistus (HbGp) hemoglobin is an oligomeric protein, presenting a quaternary structure constituted by 144 globin and 36 non-globin chains (named linkers) with a total molecular mass of 3.6 MDa. SDS effects on the oxy-HbGp thermal stability were studied, by DLS and SAXS, at pH 5.0, 7.0 and 9.0. DLS and SAXS data show that the SDS-oxy-HbGp interactions induce a significant decrease of the protein thermal stability, with the formation of larger aggregates, at pH 5.0. At pH 7.0, oxy-HbGp undergoes complete oligomeric dissociation, with increase of temperature, in the presence of SDS. Besides, oxy-HbGp 3.0mg/mL, pH 7.0, in the presence of SDS, has the oligomeric dissociation process reduced as compared to 0.5mg/mL of protein. At pH 9.0, oxy-HbGp starts to dissociate at 20 °C, and the protein is totally dissociated at 50 °C. The thermal dissociation kinetic data show that oxy-HbGp oligomeric dissociation at pH 7.0, in the presence of SDS, is strongly dependent on the protein concentration. At 0.5mg/mL of protein, the oligomeric dissociation is complete and fast at 40 and 42 °C, with kinetic constants of (2.1 ± 0.2) × 10(-4) and (5.5 ± 0.4) × 10(-4) s(-1), respectively, at 0.6 mmol/L SDS. However, at 3.0mg/mL, the oligomeric dissociation process starts at 46 °C, and only partial dissociation, accompanied by aggregates formation is observed. Moreover, our data show, for the first time, that, for 3.0mg/mL of protein, the oligomeric dissociation, denaturation and aggregation phenomena occur simultaneously, in the presence of SDS. Our present results on the surfactant-HbGp interactions and the protein thermal unfolding process correspond to a step forward in the understanding of SDS effects. Copyright © 2013 Elsevier B.V. All rights reserved.

  3. Effects of various surfactants on the dispersion stability and electrical conductivity of surface modified graphene

    Energy Technology Data Exchange (ETDEWEB)

    Uddin, Md. Elias [WCU Program, Department of BIN Fusion Technology, Chonbuk National University, Jeonju, Jeonbuk 561-756 (Korea, Republic of); Kuila, Tapas [Surface Engineering and Tribology, CSIR – Central Mechanical Engineering Research Institute, Durgapur 721 302 (India); Nayak, Ganesh Chandra [Department of Applied Chemistry, ISM Dhanbad, Dhanbad 826 004, Jharkhand (India); Kim, Nam Hoon [Department of Hydrogen and Fuel Cell Engineering, Chonbuk National University, Jeonju, Jeonbuk 561-756 (Korea, Republic of); Ku, Bon-Cheol [Institute of Advanced Composite Materials, Korea Institute of Science and Technology, Dunsan-ri, Bongdong-eup, Wanju-gun, Jeollabuk-do 864-9 (Korea, Republic of); Lee, Joong Hee, E-mail: jhl@chonbuk.ac.kr [WCU Program, Department of BIN Fusion Technology, Chonbuk National University, Jeonju, Jeonbuk 561-756 (Korea, Republic of); Department of Hydrogen and Fuel Cell Engineering, Chonbuk National University, Jeonju, Jeonbuk 561-756 (Korea, Republic of)

    2013-06-15

    Highlights: ► Water dispersible graphene has been prepared using ionic and non-ionic surfactants. ► XPS and FTIR spectra analysis confirm surface modification and reduction of GO. ► The highest water dispersibility is observed in the graphene modified with of SDBS. ► The best properties of modified graphene is achieved with GO/surfactant ratio of two. -- Abstract: Ionic and non-ionic surfactant functionalized, water dispersible graphene were prepared to investigate the effects on the dispersion stability and electrical conductivity of graphene. In this study, sodium dodecyl benzene sulfonate (SDBS), sodium dodecyl sulfate and 4-(1,1,3,3-tetramethylbutyl) phenyl-polyethylene glycol (Triton X-100) were used as ionic and non-ionic surfactants. The effects of surfactant concentrations on the dispersibility and electrical conductivity of the surface modified graphene were investigated. The dispersion stability of SDBS functionalized graphene (SDBS-G) was found to be best in water at 1.5 mg ml{sup −1}. X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy analysis indicate that the presence of surfactants does not prevent the reduction of graphene oxide (GO). These measurements also demonstrated that the surfactants were present on the surface of graphene, resulting in the formation of functionalized graphene. The thickness of different functionalized graphene was measured by Atomic force microscopy and varied significantly with different surfactants. The thermal properties of the functionalized graphene were also found to be dependent on the nature of the surfactants. The electrical conductivity of SDBS-G (108 S m{sup −1}) was comparatively higher than SDS and Triton X-100 functionalized graphene.

  4. Effects of various surfactants on the dispersion stability and electrical conductivity of surface modified graphene

    International Nuclear Information System (INIS)

    Uddin, Md. Elias; Kuila, Tapas; Nayak, Ganesh Chandra; Kim, Nam Hoon; Ku, Bon-Cheol; Lee, Joong Hee

    2013-01-01

    Highlights: ► Water dispersible graphene has been prepared using ionic and non-ionic surfactants. ► XPS and FTIR spectra analysis confirm surface modification and reduction of GO. ► The highest water dispersibility is observed in the graphene modified with of SDBS. ► The best properties of modified graphene is achieved with GO/surfactant ratio of two. -- Abstract: Ionic and non-ionic surfactant functionalized, water dispersible graphene were prepared to investigate the effects on the dispersion stability and electrical conductivity of graphene. In this study, sodium dodecyl benzene sulfonate (SDBS), sodium dodecyl sulfate and 4-(1,1,3,3-tetramethylbutyl) phenyl-polyethylene glycol (Triton X-100) were used as ionic and non-ionic surfactants. The effects of surfactant concentrations on the dispersibility and electrical conductivity of the surface modified graphene were investigated. The dispersion stability of SDBS functionalized graphene (SDBS-G) was found to be best in water at 1.5 mg ml −1 . X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy analysis indicate that the presence of surfactants does not prevent the reduction of graphene oxide (GO). These measurements also demonstrated that the surfactants were present on the surface of graphene, resulting in the formation of functionalized graphene. The thickness of different functionalized graphene was measured by Atomic force microscopy and varied significantly with different surfactants. The thermal properties of the functionalized graphene were also found to be dependent on the nature of the surfactants. The electrical conductivity of SDBS-G (108 S m −1 ) was comparatively higher than SDS and Triton X-100 functionalized graphene

  5. Antimicrobial Activity of Single-Walled Carbon Nano tubes Suspended in Different Surfactants

    International Nuclear Information System (INIS)

    Dong, L.; Alex Henderson, A.; Field, Ch.

    2012-01-01

    We investigated the antibacterial activity of single-walled carbon nano tubes (SWCNTs) dispersed in surfactant solutions of sodium cholate, sodium dodecylbenzene sulfonate, and sodium dodecyl sulfate. Among the three surfactants, sodium cholate demonstrated the weakest antibacterial activity against Salmonella enterica, Escherichia coli, and Enterococcus faecium and thereby was used to disperse bundled SWCNTs in order to study nano tube antibiotic activity. SWCNTs exhibited antibacterial characteristics for both S. enterica and E. coli. With the increase of nano tube concentrations from 0.3 mg/mL to 1.5 mg/mL, the growth curves had plateaus at lower absorbance values whereas the absorbance value was not obviously affected by the incubation ranging from 5?min to 2 h. Our findings indicate that carbon nano tubes could become an effective alternative to antibiotics in dealing with drug-resistant and multidrug-resistant bacterial strains because of the physical mode of bactericidal action that SWCNTs display

  6. Interactions between Surfactants in Solution and Electrospun Protein Fibers: Effects on Release Behavior and Fiber Properties.

    Science.gov (United States)

    Stephansen, Karen; García-Díaz, María; Jessen, Flemming; Chronakis, Ioannis S; Nielsen, Hanne M

    2016-03-07

    Intermolecular interaction phenomena occurring between endogenous compounds, such as proteins and bile salts, and electrospun compounds are so far unreported, despite the exposure of fibers to such biorelevant compounds when applied for biomedical purposes, e.g., tissue engineering, wound healing, and drug delivery. In the present study, we present a systematic investigation of how surfactants and proteins, as physiologically relevant components, interact with insulin-loaded fish sarcoplasmic protein (FSP) electrospun fibers (FSP-Ins fibers) in solution and thereby affect fiber properties such as accessible surface hydrophilicity, physical stability, and release characteristics of an encapsulated drug. Interactions between insulin-loaded protein fibers and five anionic surfactants (sodium taurocholate, sodium taurodeoxycholate, sodium glycocholate, sodium glycodeoxycholate, and sodium dodecyl sulfate), a cationic surfactant (benzalkonium chloride), and a neutral surfactant (Triton X-100) were studied. The anionic surfactants increased the insulin release in a concentration-dependent manner, whereas the neutral surfactant had no significant effect on the release. Interestingly, only minute amounts of insulin were released from the fibers when benzalkonium chloride was present. The FSP-Ins fibers appeared dense after incubation with this cationic surfactant, whereas high fiber porosity was observed after incubation with anionic or neutral surfactants. Contact angle measurements and staining with the hydrophobic dye 8-anilino-1-naphthalenesulfonic acid indicated that the FSP-Ins fibers were hydrophobic, and showed that the fiber surface properties were affected differently by the surfactants. Bovine serum albumin also affected insulin release in vitro, indicating that also proteins may affect the fiber performance in an in vivo setting.

  7. Sono-electroanalysis of copper: enhanced detection and determination in the presence of surfactants.

    Science.gov (United States)

    Hardcastle, Joanna Lorraine; Hignett, Geraldine; Melville, James L; Compton, Richard G

    2002-04-01

    Surfactant adsorption has been shown to have a passivating effect on the electrode surface during anodic stripping voltammetric measurements. In the present work the feasibility of sono-anodic stripping analysis for the determination of copper in aqueous media contaminated with surfactant has been studied at an unmodified bare glassy carbon electrode. We illustrate the deleterious effect of three common surfactants, sodium dodecyl sulfate (SDS), dodecyl pyridinium chloride (DPC) and Triton-X 100 (TX-100) on conventional electroanalysis. The analogous sono-electroanalytical response was investigated for each surfactant at ultrasound intensities above and below the cavitation threshold. The enhancement in the stripping signal observed is attributed to the increased mass transport due to acoustic streaming and above the cavitation threshold the intensity of cavitational events is significantly increased leading to shearing of adsorbed surfactant molecules from the surface. As a result accurate analyses for SDS concentrations up to 100 ppm are possible, with analytical signals visible in solutions of SDS and TX-100 of 1000 ppm. Analysis is reported in high concentration of surfactant with use of sono-solvent double extraction. The power of this technique is clearly illustrated by the ability to obtain accurate measurements of copper concentration from starting solutions containing 1000 ppm SDS or TX-100. This was also exemplified by analysis of the low concentration 0.3 microM Cu(II) solution giving a percentage recovery of 94% in the presence of 1000 ppm SDS or TX-100.

  8. Exploring the Effects of Different Types of Surfactants on Zebrafish Embryos and Larvae

    Science.gov (United States)

    Wang, Yanan; Zhang, Yuan; Li, Xu; Sun, Mingzhu; Wei, Zhuo; Wang, Yu; Gao, Aiai; Chen, Dongyan; Zhao, Xin; Feng, Xizeng

    2015-01-01

    Currently, surfactants are widely distributed in the environment. As organic pollutants, their toxicities have drawn extensive attention. In this study, the effects of anionic [sodium dodecyl sulphate (SDS) ], cationic [dodecyl dimethyl benzyl ammonium chloride (1227)] and non-ionic [fatty alcohol polyoxyethylene ether (AEO) ] surfactants on zebrafish larval behaviour were evaluated. Five behavioural parameters were recorded using a larval rest/wake assay, including rest total, number of rest bouts, rest bouts length, total activity and waking activity. The results revealed that 1227 and AEO at 1 μg/mL were toxic to larval locomotor activity and that SDS had no significant effects. Moreover, we tested the toxicities of the three surfactants in developing zebrafish embryos. AEO exposure resulted in smaller head size, smaller eye size and shorter body length relative to SDS and 1227. All three surfactants incurred concentration-dependent responses. Furthermore, in situ hybridisation indicated that smaller head size may be associated with a decreased expression of krox20. The altered expression of ntl demonstrated that the developmental retardation stemmed from inhibited cell migration and growth. These findings provide references for ecotoxicological assessments of different types of surfactants, and play a warning role in the application of surfactants. PMID:26053337

  9. Effect of ionic surfactant on the self-assembly of triblock copolymer

    Science.gov (United States)

    Ray, D.; Kohlbrecher, J.; Aswal, V. K.

    2017-05-01

    The effect of anionic surfactant sodium dodecyl sulfate (SDS) on the self-assembly of PEO-PPO-PEO triblock copolymer in aqueous solution has been studied using small-angle neutron scattering (SANS). The measurements have been carried out for fixed concentrations (1 wt%) of block copolymer and surfactant, and at varying temperatures between 20 to 80°C. Micelles of pure ionic surfactants show little change in their sizes with increasing temperature, whereas structures of the non-ionic micelles increase significantly (sphere-to-rod transition for some block copolymers). Contrast variation SANS measurement suggests addition of SDS to aqueous copolymer solutions leads to the formation of mixed micelles. Interestingly, the self-assembly of block copolymer is found to get completely arrested by the ionic surfactant in the mixed micelles which gives a control over the block copolymer phase behavior.

  10. Pyrene removal from contaminated soil using electrokinetic process combined with surfactant

    Directory of Open Access Journals (Sweden)

    Seyed Enayat Hashemi

    2015-07-01

    Full Text Available Background: Pyrene is one of the stable polycyclic aromatic hydrocarbons that is considered as an important pollutants, because of extensive distribution in the environment and carcinogenic and mutagenic properties. Among the various treatment techniques, electrokinetic method is an environmental- friendly process for organic and mineral pollutants adsorbed to soil with fine pore size the same as clay and low hydraulic conductivity soils. For improving the efficiency of pyrene removal from soil, soulobilization of pyrene from soil could be used by surfactants. Materials and Methods : In this study, clay soil was selected as model because of the specific properties. Combined method using surfactant and electrokinetic was applied for pyrene removal from soil. Experiments were designed using response surface methodology (RSM, and effect of three variables includes surfactant concentration, voltage and surfactant type were evaluated for pyrene removal from contaminated soil. Results: Pyrene removal using anionic surfactants(SDS and nonionic surfactants(TX100 as a solubilizing agents has high removal efficiency. In the optimum condition with 95% confidence coefficient, utilizing mixed surfactants of sodium dodecyl sulfate and triton X-100 with the same volume, induced of 18.54 volt and 6.53 percent surfactant concentration have 94.6% pyrene removal efficiency. Conclusion:: Results of this study shows that electrokinetic process combined with surfactant as solubilizing agent could be applied as an efficient method for treating the pyrene-contaminated soils.

  11. Polyelectrolyte surfactant aggregates and their deposition on macroscopic surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Voisin, David

    2002-07-01

    the CSC have been determined for mixtures of cationically modified guar gums (of varying charge density) with two anionic surfactants: sodium lauryl (or dodecyl) ether sulfate [SLES] and sodium dodecyl sulfate [SDS], for various concentrations of the polyelectrolyte and added sodium chloride, at room temperature. The addition of sodium chloride has only a minor net effect on the CFC, but increases the CSC significantly. The interactions between the cationic polyelectrolyte and the surfactant have been studied in the one-phase regions, i.e. below the CFC and above the CSC, using different techniques. Surface tension, electrophoresis, light scattering and viscosimetry have been employed. In the two-phase region, the sedimented floe phase has been analysed and the flocculation has been investigated. Rheology of the floe phase has been studied, after a mild compression by centrifugation. The initial rate of flocculation has been determined, using stop-flow equipment. The growth and the structure of the flocs have been investigated by light scattering. The open-network flocs of polyelectrolyte-surfactant particles grow to {approx}10's {mu}m in size, prior to their eventual settling out. Other colloidal particles can be trapped within these large flocs, and the flocs can be used to transport these particles to a macroscopic surface. The deposition and the removal of such composite flocs on glass surfaces, under flow, have been studied using a flow cell device coupled with an optical microscope. Scanning electron microscopy and atomic force microscopy have also been employed. (author)

  12. Secondary Structural Changes of Intact and Disulfide Bridges-Cleaved Human Serum Albumins in Thermal Denaturation up to 130°C - Additive Effects of Sodium Dodecyl Sulfate on the Changes.

    Science.gov (United States)

    Moriyama, Yoshiko; Takeda, Kunio

    2017-05-01

    The secondary structural changes of human serum albumin with the intact 17 disulfide bridges (HSA) and the disulfide bridges-cleaved human serum albumin (RCM-HSA) in thermal denaturation were examined. Most of the helical structures of HSA, whose original helicity was 66%, were sharply disrupted between 50 and 100°C. However, 14% helicity remained even at 130°C. The temperature dependence of the degree of disrupted helical structures of HSA was discussed in connection with questions about a general protein denaturation model. When HSA lost the disulfide bridges, about two-thirds of the original helices were disrupted. Although the helices of RCM-HSA remaining after the cleavage of the disulfide bridges were relatively resistant against the heat treatment, the helicity changed from 22% at 25°C to 14% at 130℃. The helicity of RCM-HSA at 130°C agreed with the helicity of HSA at the same temperature, indicating that the same helical moieties of the polypeptides remained unaffected at this high temperature. The additive effects of sodium dodecyl sulfate (SDS) on the structural changes of HSA and RCM-HSA in thermal denaturation were also examined. A slight amount of SDS protected the helical structures of HSA from thermal denaturation below 80°C. Upon cooling to 25°C after heat treatment at temperatures below 70°C with the coexistence of SDS of low concentrations, the helical structures of HSA were reformed to the original level at 25°C before heating. A similar tendency was also observed after heat treatment at 80°C. In contrast, the helical structures of the RCM-HSA complexes with SDS are completely recovered upon cooling to 25°C even after heat treatment up to 100°C. Similar investigations were also carried out on bovine serum albumins which had the intact 17 disulfide bridges and lost all of the bridges.

  13. Sodium dodecyl sulphate polyacrylamide gel electrophoresis (SDS ...

    African Journals Online (AJOL)

    All the three isolates had smaller proteins in the range of 13 kDa to 44 kDa. One strain of B. thuringiensis, NDR11, produced an unusual large protein of 200 kDa. Small proteins in the range of 24 kDa to 40 kDa were produced by B. laterosporus. The Cry ICPs of isolate NDR3 did not produce any electrophoretic bands, ...

  14. A Comparative Study of the Effect of Surfactant and Temperature in Fluid Interfaces

    Science.gov (United States)

    Cortes-Estrada, Aldo H.; Ibarra-Bracamontes, Laura A.; Aguilar-Corona, Alicia; Viramontes-Gamboa, Gonzalo

    2016-11-01

    A fluid interface is the boundary region formed when two immiscible fluids come into contact. One of the most important properties of fluid interfaces is the interfacial tension. The interfacial tension between two fluids can be modified by the presence of surfactant. In addition, the temperature is a relevant factor that can also modify the interfacial properties. In this work the behavior of the interface formed by oil and water in the presence of surfactant at different temperatures is presented. Interfacial tension measurements were obtained by the Pendant Drop technique. Two types of surfactant were tested, Sodium Dodecyl Sulfate (SDS) as a hydrophilic surfactant, and Sorbitan Monooleate (Span 80) as a lipophilic surfactant. The range of variations in temperature was from 25 to 60 Celsius degree. Hexane or Dodecane was used as the oil phase. The main results showed that the lipophilic surfactant showed a greater efficiency with respect to the hydrophilic surfactant used. As the temperature increased in the range considered an exponential decay for the interfacial tension was observed. This decay was dominated by the surfactant concentration. This study was supported by the Mexican Council of Science and Technology (CONACyT) and by the Scientific Research Coordination of the University of Michoacan in Mexico.

  15. Structure of sodium alkyl sulphate micelles

    International Nuclear Information System (INIS)

    Vass, Sz.

    1990-05-01

    Micellar aggregation numbers of aggregated sodium octyl, decyl, dodecyl and tetradecyl sulphate molecules obtained from small-angle neutron scattering (SANS) measurements are reported. The surfactant concentration and solution temperature were varied systematically. A survey of the physical models and evaluation algorithms applied for SANS are presented. By utilizing a new least square fitting algorithm, the formation and annihilation parameters of orthopositronium in the micellar pseudophase and in the aqueous solvent is deduced by evaluating positron lifetime spectra measured by conventional technqiues. (R.P.) 157 refs.; 10 figs

  16. Interactions in mixed micellar systems of an amphoteric chelating surfactant and ionic surfactants.

    Science.gov (United States)

    Svanedal, Ida; Persson, Gerd; Norgren, Magnus; Edlund, Håkan

    2014-02-11

    Mixtures of ionic surfactants and the chelating surfactant 2-dodecyldiethylenetriaminepentaacetic acid (4-C12-DTPA) have been examined in terms of interactions in mixed micellar systems. The amphoteric 4-C12-DTPA is zwitterionic with a negative net charge at the studied pH levels. The investigated ionic surfactants were the cationic dodecyltrimethylammonium chloride (DoTAC), the anionic sodium dodecyl sulfate (SDS), and the zwitterionic dimethyldodecylamine-N-oxide (DDAO). The surfactants all have the same hydrophobic chain lengths, and the results are evaluated in terms of headgroup interactions. 4-C12-DTPA interacts with different ionic surfactants by accepting or donating protons to the aqueous solution to increase the attractive interactions between the two surfactants; i.e., the protonation equilibrium of 4-C12-DTPA is shifted in different directions depending on whether there are predominant repulsions between positively or negatively charged groups in the mixed micelles. This was monitored by measuring pH vs concentration in the mixed systems. By measuring the pH, it was also possible to study the shift in the protonation equilibrium at increasing concentration, as the composition in the micelles approaches the composition in the total solution. Following the approach of Rubingh's regular solution theory, the interaction parameter β for mixed micelle formation was calculated from the cmc values determined by NMR diffusometry. Synergism in mixed micelle formation and negative β parameters were found in all of the investigated systems. As expected, the most negative β parameter was found in the mixture with DoTAC, followed by DDAO and SDS. The self-diffusion in the 4-C12-DTPA/DoTAC system was also discussed. The self-diffusion coefficient vs concentration plots show two distinctly different curves, depending on the surfactant that is present in excess.

  17. The study of The study of the influence of temperature on surfactants – polyethylene glycol layers The study of the influence of temperature on surfactants – polyethylene glycol layers on liquid-gas interface liquid-gas interfacethe influence of temperature on surfactants – polyethylene glycol layers on liquid-gas interfaceThe study of the influence of temperature on surfactants – polyethylene glycol layers on liquid-gas interface

    Directory of Open Access Journals (Sweden)

    Seryk Boloshaan

    2015-03-01

    Full Text Available The surface tension of compositions consisting of nonionic polyethylene glycol and surface active substances of different nature and influence of temperatures on properties of their adsorption layers were studied. To be taken into account the basics of classical chemical thermodynamics and colloidal chemistry, the thermodynamic parameters were determined for the adsorption of glycol, cetyl pyridinium bromide, Tween- 80 and sodium dodecyl sulfate. Adsorption speed was valuated By Kinetic curves of a liquid /gas interfaces. As a surfactants were taken the anionic surfactantsodium dodecylsulphate, cationic surfactant cetylpyridinium bromide and nonionic Tween-80. The reason of using nonionic polyethyleneglycol as polymer is that the polymer is not toxic, biodegradable and it has no harm to the human body. That is why they are largely used in food industry, pharmaceutics, cosmetics and household chemical products.

  18. Adsorption of anionic surfactants from aqueous solution by high content of primary amino crosslinked chitosan microspheres.

    Science.gov (United States)

    Zhang, Caihong; Wen, Haifeng; Huang, Yingying; Shi, Wenjian

    2017-04-01

    High content of primary amino crosslinked chitosan microspheres (ACCMs) were synthesized and characterized with IR, XRD and SEM technologies. Subsequently, ACCMs were adopted to adsorb three common anionic surfactants from aqueous solution: sodium dodecyl benzene sulfonate (SDBS), sodium lauryl sulfate (SLS), and sodium dodecyl sulfonate (SDS). The adsorption performances were evaluated based on different variables such as the pH, contact time, temperature and initial concentration of the anionic surfactants. Moreover, the adsorption were investigated with kinetic models, equilibrium isotherms and thermodynamic models. The experimental results indicated that the adsorption processes were fitted very well with a pseudo-second-order model. The adsorption isotherms could be better described by Langmuir model rather than Freundlich model. The adsorption of SDBS was a spontaneous, exothermic process. While the adsorption of SLS and SDS were spontaneous, endothermic. The adsorption processes were complex physical-chemistry adsorption models, which are dominated by physisorption. Furthermore, this study found that the material had strong absorption abilities for anionic surfactants, the saturation adsorption capacity of ACCMs were 1220mg/g for SDBS, 888mg/g for SLS, and 825mg/g for SDS at pH 3.0 and 298K, respectively. The adsorption capacity was reduced only 5.7% after 8 cycles of the adsorption-desorption processes. Copyright © 2017 Elsevier B.V. All rights reserved.

  19. Surfactant media for constant-current coulometry. Application for the determination of antioxidants in pharmaceuticals

    Energy Technology Data Exchange (ETDEWEB)

    Ziyatdinova, Guzel, E-mail: Ziyatdinovag@mail.ru [Analytical Chemistry Department, A.M. Butlerov Institute of Chemistry, Kazan (Volga Region) Federal University, Kremlyevskaya, 18, Kazan 420008 (Russian Federation); Ziganshina, Endzhe; Budnikov, Herman [Analytical Chemistry Department, A.M. Butlerov Institute of Chemistry, Kazan (Volga Region) Federal University, Kremlyevskaya, 18, Kazan 420008 (Russian Federation)

    2012-09-26

    Highlights: Black-Right-Pointing-Pointer Applicability of surfactants in constant-current coulometry is shown for the first time. Black-Right-Pointing-Pointer Reactions of antioxidants with electrogenerated titrants in surfactant media are investigated. Black-Right-Pointing-Pointer Water insoluble antioxidants can be determined in water media with addition of surfactants. Black-Right-Pointing-Pointer Coulometric determination of antioxidants in pharmaceutical dosage forms using surfactants media is developed. - Abstract: Effect of surfactant presence on electrochemical generation of titrants has been evaluated and discussed for the first time. Cationic (1-dodecylpyridinium and cetylpyridinium bromide), anionic (sodium dodecyl sulfate) and nonionic (Triton X100 and Brij{sup Registered-Sign} 35) surfactants as well as nonionic high molecular weight polymer (PEG 4000) do not react with the electrogenerated bromine, iodine and hexacyanoferrate(III) ions. The electrogenerated chlorine chemically interact with Triton X100 and Brij{sup Registered-Sign} 35. The allowable range of surfactants concentrations providing 100% current yield has been found. Chain-breaking low molecular weight antioxidants (ascorbic acid, rutin, {alpha}-tocopherol and retinol) were determined by reaction with the electrogenerated titrants in surfactant media. Nonionic and cationic surfactants can be used for the determination of antioxidants by reaction with the electrogenerated halogens. On contrary, cationic surfactants gives significantly overstated results of antioxidants determination with electrogenerated hexacyanoferrate(III) ions. The use of surfactants in coulometry of {alpha}-tocopherol and retinol provides their solubilization and allows to perform titration in water media. Simple, express and reliable coulometric approach for determination of {alpha}-tocopherol, rutin and ascorbic acid in pharmaceuticals using surfactant media has been developed. The relative standard deviation of the

  20. Mutations in a helix-1 motif of the ATP synthase c-subunit of Bacillus pseudofirmus OF4 cause functional deficits and changes in the c-ring stability and mobility on sodium dodecyl sulfate-polyacrylamide gel electrophoresis.

    Science.gov (United States)

    Liu, Jun; Fackelmayer, Oliver J; Hicks, David B; Preiss, Laura; Meier, Thomas; Sobie, Eric A; Krulwich, Terry A

    2011-06-21

    The ATP synthase of the alkaliphile Bacillus pseudofirmus OF4 has a tridecameric c-subunit rotor ring. Each c-subunit has an AxAxAxA motif near the center of the inner helix, where neutralophilic bacteria generally have a GxGxGxG motif. Here, we studied the impact of four single and six multiple Ala-to-Gly chromosomal mutations in the A16xAxAxA22 motif on the capacity for nonfermentative growth and, for most of the mutants, on ATP synthesis by ADP- and P(i)-loaded membrane vesicles at pH 7.5 and 10.5. Sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) analyses of the holo-ATP synthases were used to probe stability of the mutant c-rotors and mobility properties of the c-rotors as well as the monomeric c-subunits that are released from them by trichloroacetic acid treatment. Mutants containing an Ala16-to-Gly mutation exhibited the most severe functional defects. Via SDS-PAGE, most of the mutant c-monomers exhibited increased mobility relative to the wild-type (WT) c-subunit, but among the intact c-rings, only Ala16-to-Gly mutants exhibited significantly increased mobility relative to that of the WT c-ring. The hypothesis that these c-rings have a decreased c-subunit stoichiometry is still untested, but the functional impact of an Ala16-to-Gly mutation clearly depended upon additional Ala-to-Gly mutation(s) and their positions. The A16/20G double mutant exhibited a larger functional deficit than both the A16G and A16/18G mutants. Most of the mutant c-rings showed in vitro instability relative to that of the WT c-ring. However, the functional deficits of mutants did not correlate well with the extent of c-ring stability loss, so this property is unlikely to be a major factor in vivo.

  1. Evaluation of a Porcine Gastric Mucin and RNase A Assay for the Discrimination of Infectious and Non-infectious GI.1 and GII.4 Norovirus Following Thermal, Ethanol, or Levulinic Acid Plus Sodium Dodecyl Sulfate Treatments.

    Science.gov (United States)

    Afolayan, Olamide T; Webb, Cathy C; Cannon, Jennifer L

    2016-03-01

    Human noroviruses (NoVs) are a major source of foodborne illnesses worldwide. Since human NoVs cannot be cultured in vitro, methods that discriminate infectious from non-infectious NoVs are needed. The purpose of this study was to evaluate binding of NoV genotypes GI.1 and GII.4 to histo-blood group antigens expressed in porcine gastric mucin (PGM) as a surrogate for detecting infectious virus following thermal (99 °C/5 min), 70% ethanol or 0.5% levulinic acid (LV) plus 0.01 or 0.1% sodium dodecyl sulfate (SDS) sanitizer treatments and to determine the limit of detection of GI.1 and GII.4 binding to PGM. Treated and control virus samples were applied to 96-well plates coated with 1 µg/ml PGM followed by RNase A (5 ng/µl) treatment for degradation of exposed RNA. Average log genome copies per ml (gc/ml) reductions and relative differences (RD) in quantification cycle (Cq) values after thermal treatment were 1.77/5.62 and 1.71/7.25 (RNase A) and 1.73/5.50 and 1.56/6.58 (no RNase A) for GI.1 and GII.4, respectively. Treatment of NoVs with 70% EtOH resulted in 0.05/0.16 (GI.1) and 3.54/10.19 (GII.4) log reductions in gc/ml and average RD in Cq value, respectively. LV (0.5%) combined with 0.1 % SDS provided a greater decrease of GI.1 and GII.4 NoVs with 8.97 and 8.13 average RD in Cq values obtained, respectively than 0.5% LV/0.01 % SDS. Virus recovery after PGM binding was variable with GII.4 > GI.1. PGM binding is a promising surrogate for identifying infectious and non-infectious NoVs after capsid destruction, however, results vary depending on virus strain and inactivation method.

  2. Dynamics of Surfactant Clustering at Interfaces and Its Influence on the Interfacial Tension: Atomistic Simulation of a Sodium Hexadecane-Benzene Sulfonate-Tetradecane-Water System.

    Science.gov (United States)

    Paredes, Ricardo; Fariñas-Sánchez, Ana Isabel; Medina-Rodrı Guez, Bryan; Samaniego, Samantha; Aray, Yosslen; Álvarez, Luis Javier

    2018-03-06

    The process of equilibration of the tetradecane-water interface in the presence of sodium hexadecane-benzene sulfonate is studied using intensive atomistic molecular dynamics simulations. Starting as an initial point with all of the surfactants at the interface, it is obtained that the equilibration time of the interface (several microseconds) is orders of magnitude higher than previously reported simulated times. There is strong evidence that this slow equilibration process is due to the aggregation of surfactants molecules on the interface. To determine this fact, temporal evolution of interfacial tension and interfacial formation energy are studied and their temporal variations are correlated with cluster formation. To study cluster evolution, the mean cluster size and the probability that a molecule of surfactant chosen at random is free are obtained as a function of time. Cluster size distribution is estimated, and it is observed that some of the molecules remain free, whereas the rest agglomerate. Additionally, the temporal evolution of the interfacial thickness and the structure of the surfactant molecules on the interface are studied. It is observed how this structure depends on whether the molecules agglomerate or not.

  3. Surfactant-induced mobilisation of trace metals from estuarine sediment: Implications for contaminant bioaccessibility and remediation

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Anu [School of Earth, Ocean and Environmental Sciences, University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom); Turner, Andrew [School of Earth, Ocean and Environmental Sciences, University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom)], E-mail: aturner@plymouth.ac.uk

    2009-02-15

    The mobilisation of metals (Al, Fe, Cd, Cu, Mn, Ni, Pb, Sn, Zn) from contaminated estuarine sediment has been examined using commercially available surfactants. Metal release by the anionic surfactant, sodium dodecyl sulphate (SDS), increased with increasing amphiphile concentration up to and above its critical micelle concentration (CMC). Metal mobilisation by the bile acid salt, sodium taurocholate, and the nonionic surfactant, Triton X-100, however, did not vary with amphiphile concentration. SDS was the most efficient surfactant in mobilising metals from the sample, and Cd, Cu and Ni were released to the greatest extents (12-18% of total metal at [SDS] > CMC). Metal mobilisation appeared to proceed via complexation with anionic amphiphiles and denudation of hydrophobic host phases. Surfactants may play an important role in the solubilisation of metals in the digestive environment of deposit-feeding animals and, potentially, in the remediation of metal-contaminated soil and sediment. - Significant quantities of metals are mobilised from estuarine sediment by commercially available surfactants.

  4. Surfactant-enhanced electrokinetic remediation of soil contaminated with hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Yang, J.W.; Park, J.Y.; Lee, H.H.; Cho, H.J. [Dept. of Chemical Engineering, Korea Advanced Inst. of Science and Technology, Taejon (Korea)

    2001-07-01

    Removal of hydrophobic organic contaminants (HOCs) using electrokinetic method was studied in a model system. Kaolinite and phenanthrene were selected as the model clay soil and representative HOC. Three different types of surfactants, APG (alkyl polyglucoside), Brij30 (polyoxyethylene 4 lauryl ether), and SDS (sodium dodecyl sulfate), were used to enhance the solubility of HOCs. Electrokinetic (EK) column experiments were performed using water, surfactant solution, and acetate buffer solution under a constant current condition. Voltage and flow through the soil system were interpreted with time. Electrolyte pH at the anode and cathode compartments was observed for operation time. Removal efficiency of phenanthrene was examined after the end of EK operation during 2, 4, and 6 weeks. (orig.)

  5. Controlling block copolymer phase behavior using ionic surfactant

    Energy Technology Data Exchange (ETDEWEB)

    Ray, D.; Aswal, V. K. [Solid State Physics Division, Bhabha Atomic Research Centre, Mumbai 400 085, India E-mail: debes.phys@gmail.com (India)

    2016-05-23

    The phase behavior of poly(ethylene oxide)-poly(propylene oxide-poly(ethylene oxide) PEO-PPO-PEO triblock copolymer [P85 (EO{sub 26}PO{sub 39}EO{sub 26})] in presence of anionic surfactant sodium dodecyl sulfate (SDS) in aqueous solution as a function of temperature has been studied using dynamic light scattering (DLS) and small-angle neutron scattering (SANS). The measurements have been carried out for fixed concentrations (1 wt%) of block copolymer and surfactants. Each of the individual components (block copolymer and surfactant) and the nanoparticle–surfactant mixed system have been examined at varying temperature. The block copolymer P85 forms spherical micelles at room temperature whereas shows sphere-to-rod like micelle transition at higher temperatures. On the other hand, SDS surfactant forms ellipsoidal micelles over a wide temperature range. Interestingly, it is found that phase behavior of mixed micellar system (P85 + SDS) as a function of temperature is drastically different from that of P85, giving the control over the temperature-dependent phase behavior of block copolymers.

  6. Spontaneous vesicle phase formation by pseudogemini surfactants in aqueous solutions.

    Science.gov (United States)

    Sun, Nan; Shi, Lijuan; Lu, Fei; Xie, Shuting; Zheng, Liqiang

    2014-08-14

    The phase behavior of a kind of pseudogemini surfactant in aqueous solutions, formed by the mixture of sodium dodecyl benzene sulfonate (SDBS) and butane-1,4-bis (methylimidazolium bromide) ([mim-C4-mim]Br2) or butane-1,4-bis(methylpyrrolidinium bromide) ([mpy-C4-mpy]Br2) in a molar ratio of 2 : 1, is reported in the present work. When [mim-C4-mim]Br2 or [mpy-C4-mpy]Br2 is mixed with SDBS in aqueous solutions, one cationic [mim-C4-mim]Br2 or [mpy-C4-mpy]Br2 molecule "bridges" two SDBS molecules by noncovalent interactions (e.g. electrostatic, π-π stacking, and σ-π interactions), behaving like a pseudogemini surfactant. Vesicles can be formed by this kind of pseudogemini surfactant, determined by freeze-fracture transmission electron microscopy (FF-TEM) or cryogenic-transmission electron microscopy (cryo-TEM) and dynamic light scattering (DLS). The mixed system of sodium dodecyl sulfate (SDS) with [mim-C4-mim]Br2 or [mpy-C4-mpy]Br2 was also constructed, and only micelles were observed. We infer that a pseudogemini surfactant is formed under the synergic effect of electrostatic, π-π stacking, and σ-π interactions in the SDBS/[mim-C4-mim]Br2/H2O system, while electrostatic attraction and hydrophobic interactions may provide the directional force for vesicle formation in the SDBS/[mpy-C4-mpy]Br2/H2O system.

  7. Influence of anionic surfactant on the process of electro-Fenton decolorized methyl orange.

    Science.gov (United States)

    Ren, B X

    2010-01-01

    The electro-Fenton process has been shown to be very successful to remove dyes from water. However, the influence of other constituents in dyeing industry wastewater, such as Sodium Dodecyl Sulfate (SDS) surfactants, has not been investigated. In this study, the effect of SDS surfactant on the kinetics of Methyl Orange degradation undergoing Electro-Fenton process was investigated. Results show that Methyl Orange degradation rate decreased as SDS concentration (below Critical Micelle Concentration, CMC) increased, which was attributed to the consumption of hydroxyl radicals (( )OH) by surfactants. The kinetics modeling indicates the reaction was the first-order reaction to Methyl Orange even SDS existing. The pseudo first-order rate constants decreased as SDS concentration increased.

  8. Effect of anionic surfactants on the process of Fenton degradation of methyl orange.

    Science.gov (United States)

    Yang, C W; Wang, D

    2009-01-01

    Fenton process has been shown to be very successful to remove dyes from water. However, the influence of other constituents in dyeing industry wastewater, such as Sodium Dodecyl Sulphate (SDS) surfactants, has not been investigated. In this study, the effect of SDS surfactant on the kinetics of Methyl Orange degradation undergoing Fenton process was investigated. Results show that Methyl Orange degradation rate decreased as SDS concentration increased, which was attributed to the consumption of hydroxyl radicals (OH) by surfactants and the formation of Methyl Orange-SDS complex. No evidence was found that the Methyl Orange degradation pathway was affected by the presence of SDS. The kinetics modelling indicates the reaction was the first-order reaction to Methyl Orange.

  9. Preparation, Characterization and Performance Studies of Active PVDF Ultrafiltration-Surfactants Membranes Containing PVP as Additive

    International Nuclear Information System (INIS)

    Nur Izzah Md Fadilah; Abdul Rahman Hassan

    2016-01-01

    The role of surfactants in the formation of active Poly(vinylidene fluoride) (PVDF) ultrafiltration (AUF) membranes was studied. The effect combination of surfactants that are Sodium dodecyl sulfate (SDS)/ Tween 80 and Tween 80/ Triton X-100 formulations on performance and morphological structures were investigated for the first time. The influence of surfactants blends on the membrane pores was also examined. Experimental data showed that combination of Tween 80/ Triton X-100 give the highest BSA permeation flux with a value of 285.51 Lm -2 h -1 . With combination of SDS/ Tween 80, the AUF membrane showed the highest protein rejection up to 93 % and 79 % for Bovine Serum Albumin (BSA) and Egg Albumin (EA), respectively. Moreover, membranes characterization demonstrated that the addition of SDS/ Tween 80 and Tween 80/ Triton X-100 were found to affect the performance, surface morphologies and membrane pores of AUF PVDF membranes. (author)

  10. [Influence of Different Type of Surfactant on Bacteriolytic Activity of Lysozyme].

    Science.gov (United States)

    Ivanov, R A; Soboleva, O A; Smirnov, S A; Levashov, P A

    2015-01-01

    The influence ofvarious surfactants (anionic sodium dodecyl sulfate, SDS, cationic dodecyltrimethylarnmonium bromide, DTAB, and zwitterionic cocoamidopropylbetaine, CAPB) on the activity of the chicken egg lysozyme is investigated. Lysis of Gram-positive bacteria by the enzyme was carried out at pH 7.2 and ionic strength of 0.15 M. It was found that at low SDS and DTAB concentrations (less than 1 x 10(-5) M) the bacteriolytic activity increases by 30-140%. At higher concentrations (1 x 10(-5) - 1 x 10(4) M) the activity returns to the level observed in the absence of the surfactants. The elevated activity correlated with the formation of hydrophobic lysozyme-surfactant complexes. Introduction of CAPB at concentrations above 1 x 10(-5) M sig, nificantly diminished the bacteriolytic activity due to CAPB induced aggregation of lysozyme.

  11. Thermodynamics of self-assembling of mixture of a cationic gemini surfactant and sodium dodecylsulfate in aqueous solution: Calorimetry, conductivity and surface pressure measurements

    International Nuclear Information System (INIS)

    Bai, Guangyue; Wang, Yujie; Ding, Yanhong; Zhuo, Kelei; Wang, Jianji; Bastos, Margarida

    2016-01-01

    Highlights: • ITC provided thermodynamic characterization of self-association of oppositely charged gemini/SDS surfactants. • Phase transitions and corresponding enthalpies were obtained by ITC. • The transitions reflect a change in morphology, supported by Cryo-TEM images. • Conductivity and ITC results show very good agreement. • An asymmetric distribution of surfactants in the aggregates is supported by results. - Abstract: The thermodynamics and phase behavior of mixtures of cationic gemini surfactant decanediyl-α,ω-bis(dodecyldimethylammonium bromide) (12-10-12) and sodium dodecylsulfate (SDS) were studied in the dilute SDS-rich region. The enthalpy of interaction between both surfactant monomers before the critical micelle concentration for the mixture (cmc mix ) was determined by isothermal titration calorimetry (ITC). After the cmc mix , ITC results exhibited a first process associated with a large endothermic enthalpy change followed by a second one with a very small exothermic enthalpy change. In the same regions, the conductivity curves show an increase in slope after the break, followed by a plateau region, respectively for the two processes. The combined results from the various methodologies used lead us to propose that the first process reflects the formation of non-spherical micelles and the second one the vesicle formation. The area per catanionic complex was obtained through surface pressure measurements, leading to an apparent packing parameter ⩾1. The observed behavior may be rationalized on the basis of the hypothesis that both surfactants distribute asymmetrically in the vesicle bilayers and unevenly in the non-spherical micelle. In order to get structural information Cryo-TEM experiments were performed, which provided images that support this interpretation. From all the information gathered a phase diagram was mapped, including three one-phase regions of spherical micelles, non-spherical micelles and vesicles.

  12. Effect of Four Commonly Used Dissolution Media Surfactants on Pancreatin Proteolytic Activity.

    Science.gov (United States)

    Guncheva, Maya; Stippler, Erika

    2017-05-01

    Proteolytic enzymes are often used in dissolution testing of cross-linked gelatin capsules that do not conform to the dissolution specification. Their catalytic activity, however, can be affected when they are added to a dissolution media containing solubility enhancers, such as surfactants. The aim of this study was to assess the activity of pancreatic proteases in presence of four commonly used surfactants. We found that pancreatin exhibits remarkable proteolytic activity in the presence of Tween 80, even at the concentrations as high as 250 times its critical micelle concentration (cmc) in water, whereas, Triton X-100 enhanced the proteolytic activity of pancreatin when added at concentrations above its cmc in water. Both surfactants are non-ionic surfactants. On the other hand, sodium dodecyl sulfate (SDS) and cetyltrimethylammonium bromide (CTAB), which are ionic surfactants, have a detrimental effect on the proteolytic activity of pancreatin. For example, a 50% reduction of the pancreatin activity was found in samples which contain a minor amount of SDS (0.05% w/v) in comparison to a surfactant-free reaction. Additionally, no activity was observed for the pancreatin-SDS samples which were incubated for 30 min at 40°C prior to testing. CTAB had an impact on pancreatin activity at concentrations higher than its cmc. Data from this manuscript can be used as a benchmark for optimization of the dissolution procedures that require use of both surfactants and enzymes.

  13. Perfluorinated Alcohols Induce Complex Coacervation in Mixed Surfactants.

    Science.gov (United States)

    Jenkins, Samuel I; Collins, Christopher M; Khaledi, Morteza G

    2016-03-15

    Recently, we reported a unique and nearly ubiquitous phenomenon of inducing simple and complex coacervation in solutions of a broad variety of individual and mixed amphiphiles and over a wide range of concentrations and mole fractions. This paper describes a novel type of biphasic separation in aqueous solutions of mixed cationic-anionic (catanionic) surfactants induced by hexafluoroisopropanol (HFIP). The test cases included mixtures of cetyltrimethylammonium bromide (CTAB) and sodium dodecyl sulfate (SDS) (surfactants with different carbon chain lengths) as well as dodecyltrimethylammonium bromide (DTAB) with SDS (surfactants with the same carbon chain lengths). The CTAB-SDS-HFIP coacervate systems can be produced at many different mole ratios of surfactant, but DTAB-SDS-HFIP formed only coacervates at equimolar (1:1) mole ratios of DTAB and SDS. The phase-transition behavior of both systems was studied over a wide range of surfactant and HFIP concentrations at the stoichiometric (1:1) mole ratio of cationic/anionic surfactants. The chemical compositions of each of the two phases (aqueous-rich and coacervate phases) were studied with regard to the concentrations of HFIP, water, and individual surfactants. It is revealed that the surfactant-rich phase (coacervate phase) contains a large percentage of fluoroalcohol relative to the aqueous phase and is enriched in both surfactants but contains a small percentage of water. Surprisingly, the concentration of water in the coacervate phase increases as the total HFIP concentration is increased while the concentration of HFIP in the coacervate phase remains relatively constant, which means a larger amount of water associated with HFIP molecules is extracted into the coacervate phase, which results in the growth of the phase. The volume of the coacervate phase increases with an increase in surfactant concentration and total HFIP %. The coacervate phase is highly enriched in the two amphiphilic ions (DTA(+) and DS

  14. Study of adjuvant effect of model surfactants from the groups of alkyl sulfates, alkylbenzene sulfonates, alcohol ethoxylates and soaps.

    Science.gov (United States)

    Clausen, S K; Sobhani, S; Poulsen, O M; Poulsen, L K; Nielsen, G D

    2000-11-01

    The sodium salts of representatives of anionic surfactants, dodecylbenzene sulfonate (SDBS), dodecyl sulfate (SDS) and coconut oil fatty acids, and a nonionic surfactant, dodecyl alcohol ethoxylate, were studied for adjuvant effect on the production of specific IgE antibodies in mice. The surfactants were injected subcutaneously (sc) in concentrations of 1000, 100, 10 or 1 mg/l, respectively, together with 1 microg of ovalbumin (OVA). In addition, groups of mice received OVA in saline (control group) or in Al(OH)(3) (positive adjuvant control group). After the primary immunization the mice were boosted up to three times with OVA (0.1 microg sc) in saline. OVA-specific IgE antibodies were determined by the heterologous mouse rat passive cutaneous anaphylaxis test. The results were confirmed by a specific ELISA method. After the first booster, the Al(OH)(3) group and the 10 mg/l SDS group showed a statistically significant increase in OVA specific IgE levels. After two boosters, a statistically significant suppression in OVA-specific IgE production occurred with SDS (1000 mg/l), SDBS (1000 and 100 mg/l), coconut soap (1000 mg/l) and the alcohol ethoxylate (10 mg/l). This study suggests that a limited number of surfactants possess an adjuvant effect whereas all surfactants at certain levels can suppress specific IgE production.

  15. Maillard Conjugation of Sodium Alginate to Whey Protein for Enhanced Resistance to Surfactant-Induced Competitive Displacement from Air-Water Interfaces.

    Science.gov (United States)

    Cai, Bingqing; Saito, Anna; Ikeda, Shinya

    2018-01-24

    Whey protein adsorbed to an interface forms a viscoelastic interfacial film but is displaced competitively from the interface by a small-molecule surfactant added afterward. The present study evaluated the impact of the covalent conjugation of high- or low-molecular-weight sodium alginate (HA or LA) to whey protein isolate (WPI) via the Maillard reaction on the ability of whey protein to resist surfactant-induced competitive displacement from the air-water interface. Surfactant added after the pre-adsorption of conjugate to the interface increased surface pressure. At a given surface pressure, the WPI-LA conjugate showed a significantly higher interfacial area coverage and lower interfacial film thickness compared to those of the WPI-HA conjugate or unconjugated WPI. The addition of LA to the aqueous phase had little effect on the interfacial area and thickness of pre-adsorbed WPI. These results suggest the importance of the molecular weight of the polysaccharide moiety in determining interfacial properties of whey protein-alginate conjugates.

  16. A small-angle X-ray scattering study of complexes formed in mixtures of a cationic polyelectrolyte and an anionic surfactant

    DEFF Research Database (Denmark)

    Bergström, M.; Kjellin, U.R.M.; Claesson, P.M.

    2002-01-01

    The internal structure of the solid phase formed in mixtures of the anionic surfactant sodium dodecyl sulfate (SDS) and a range of oppositely charged polyelectrolytes with different side chains and charge density has been investigated using small-angle X-ray scattering. Polyelectrolytes with short....... The hexagonal structure of MAPTAC is retained either when a neutral monomer (acrylamide, AM) is included in the polymer backbone to reduce the charge density or when a nonionic surfactant is admixed to the SDS/polyelctrolyte complex.. The unit cell length of AM-MAPTAC increases with decreasing charge density...... structure and the bilayers in the lamellar structure are based on self-assembled surfactant aggregates with the polyelectrolyte mainly located in the aqueous region adjacent to the charged surfactant headgroups....

  17. Sodium

    Science.gov (United States)

    Table salt is a combination of two minerals - sodium and chloride Your body needs some sodium to work properly. It helps with the function ... in your body. Your kidneys control how much sodium is in your body. If you have too ...

  18. Destabilization Mechanism of Ionic Surfactant on Curcumin Nanocrystal against Electrolytes

    Directory of Open Access Journals (Sweden)

    Heni Rachmawati

    2016-10-01

    Full Text Available We have successfully developed curcumin nanosuspension intended for oral delivery. The main purpose is to improve bioavailability through enhancing its solubility. The nanoparticles were stabilized using various stabilizers, including polyvinyl pyrrolidone (PVP, polyvinyl alcohol (PVA, sodium carboxymethylcellulose (Na-CMC, d-α-tocopheryl polyethylene glycol 1000 succinate (TPGS, and sodium dodecyl sulfate (SDS. The average diameter of particles, microscopic appearance, and sedimentation of each preparation was observed and compared. Each stabilizer demonstrated a different degree of inhibition of particle aggregation under electrolyte-containing simulated gastrointestinal (GIT fluid. Non-ionic stabilizers (PVA, PVP, and TPGS were shown to preserve the nanosuspension stability against electrolytes. In contrast, strong ionic surfactants such as SDS were found to be very sensitive to electrolytes. The results can provide useful information for the formulators to choose the most suitable stabilizers by considering the nature of stabilizers and physiological characteristics of the target site of the drug.

  19. Non toxic biodegradable cationic gemini surfactants as novel corrosion inhibitor for mild steel in hydrochloric acid medium and synergistic effect of sodium salicylate: Experimental and theoretical approach

    Energy Technology Data Exchange (ETDEWEB)

    Mobin, Mohammad, E-mail: drmmobin@hotmail.com; Aslam, Ruby; Aslam, Jeenat

    2017-04-15

    Two biodegradable, non toxic cationic gemini surfactants having ester linkage in the spacer namely, C{sub m}H{sub 2m+1}(CH{sub 3}){sub 2}N{sup +}(CH{sub 2}COOCH{sub 2}){sub 2}N{sup +}(CH{sub 3}){sub 2}C{sub m}H{sub 2m+1}.2Cl{sup -} (m-E2-m, m = 12, 14), were synthesized and characterized using elemental analysis, FT-IR and {sup 1}H-NMR. The corrosion inhibition performance of synthesized compounds separately and in combination with sodium salicylate (SS), along with the nature and stability of inhibitive film, for mild steel (MS) in 1 M HCl solution at 30–60 °C was evaluated using weight loss, potentiodynamic polarization, EIS, UV–visible spectroscopy, FTIR, SEM/EDAX, TGA and quantum chemical calculations. Results of the studies confirm m-E2-m as effective corrosion inhibitor for MS in HCl; the inhibition effect being synergistically strengthened in presence of SS. The synthesized compounds act as mixed type inhibitor and adsorb on MS surface in accordance with Langmuir adsorption isotherm. Experimentally measured inhibition efficiencies are correlated with the molecular parameters obtained using PM6 semi-empirical method. Empirical results are in good agreement with the theoretical predictions. - Graphical abstract: (a) Optimized geometry of studied inhibitors by PM6 method with (b) HOMO and (c) LUMO orbital occupation. - Highlights: • Environment friendly gemini surfactants were studied as corrosion inhibitor for MS. • Studied compounds act as good inhibitor for MS corrosion in 1 M HCl at 30–60 °C. • η of inhibitors is synergistically increased in presence of sodium salicylate. • The synthesized cationic gemini surfactants act as mixed-type inhibitor. • Experimentally obtained results are in good agreement with theoretical results.

  20. Comparative evaluation of antibacterial property and substantivity of chlorhexidine containing dentifrices with sodium lauryl sulfate and Tween as surfactants: An in vivo study

    Directory of Open Access Journals (Sweden)

    V Venu

    2013-01-01

    Full Text Available Aim: The aim of the study was to determine the antibacterial property and substantivity of chlorhexidine containing dentifrices with sodium lauryl sulfate (SLS and Tween as surfactants. Materials and Methods: It is a double-blind cross over the study, a total of 20 children within their mixed dentition period (7-13 year having Streptococci mutans count more than 10 6 were selected for the main study. Three types of chlorhexidine containing dentifrices were used with a washout period of 1 week. Out of the three toothpastes, one was without surfactant and other two toothpastes contained SLS and Tween as surfactants respectively. 20 volunteers brushed for 1 min during the study day with their assigned toothpaste. Saliva samples were collected before brushing, immediately after brushing and 1, 3, 5, and 7 hand sent for microbial analysis. The culture carried out by inoculating saliva sample onto Mitis salivarius agar for selective isolation of S. mutans followed by counting of colony forming unit. Results: Group I and III (Chlorhexidine and CHX + Tween had shown statistically significant reduction in bacterial count until 7 h when compared to their baseline values ( P < 0.001. Group II toothpaste (CHX + SLS had shown significant reduction in bacterial count until 3 h only. On inter group comparison, Group III had shown good amount of percentage reduction in bacterial count when compared to other groups. Conclusion: CHX + Tween toothpaste had shown statistically significant reduction in antibacterial activity and substantivity than other groups. These findings show chlorhexidine containing toothpaste with non-ionic surfactant will be able to maintain the antibacterial property and substantivity of chlorhexidine.

  1. Phase transitions in surfactant monolayers

    International Nuclear Information System (INIS)

    Casson, B.D.

    1998-01-01

    Two-dimensional phase transitions have been studied in surfactant monolayers at the air/water interface by sum-frequency spectroscopy and ellipsometry. In equilibrium monolayers of medium-chain alcohols C n H 2n+1 OH (n = 9-14) a transition from a two-dimensional crystalline phase to a liquid was observed at temperatures above the bulk melting point. The small population of gauche defects in the solid phase increased only slightly at the phase transition. A model of the hydrocarbon chains as freely rotating rigid rods allowed the area per molecule and chain tilt in the liquid phase to be determined. The area per molecule, chain tilt and density of the liquid phase all increased with increasing chain length, but for each chain length the density was higher than in a bulk liquid hydrocarbon. In a monolayer of decanol adsorbed at the air/water interface a transition from a two-dimensional liquid to a gas was observed. A clear discontinuity in the coefficient of ellipticity as a function of temperature showed that the transition is first-order. This result suggests that liquid-gas phase transitions in surfactant monolayers may be more widespread than once thought. A solid-liquid phase transition has also been studied in mixed monolayers of dodecanol with an anionic surfactant (sodium dodecyl sulphate) and with a homologous series of cationic surfactants (alkyltrimethylammonium bromides: C n TABs, n = 12, 14, 16). The composition and structure of the mixed monolayers was studied above and below the phase transition. At low temperatures the mixed monolayers were as densely packed as a monolayer of pure dodecanol in its solid phase. At a fixed temperature the monolayers under-went a first-order phase transition to form a phase that was less dense and more conformationally disordered. The proportion of ionic surfactant in the mixed monolayer was greatest in the high temperature phase. As the chain length of the C n TAB increased the number of conformational defects

  2. Isolation of surfactant-resistant pseudomonads from the estuarine surface microlayer.

    Science.gov (United States)

    Louvado, Antonio; Coelho, Francisco J R C; Domingues, Patricia; Santos, Ana L; Gomes, Newton C M; Almeida, Adelaide; Cunha, Angela

    2012-03-01

    Bioremediation efforts often rely on the application of surfactants to enhance hydrocarbon bioavailability. However, synthetic surfactants can sometimes be toxic to degrading microorganisms, thus reducing the clearance rate of the pollutant. Therefore, surfactant-resistant bacteria can be an important tool for bioremediation efforts of hydrophobic pollutants, circumventing the toxicity of synthetic surfactants that often delay microbial bioremediation of these contaminants. In this study, we screened a natural surfactant-rich compartment, the estuarine surface microlayer (SML), for cultivable surfactant-resistant bacteria using selective cultures of sodium dodecyl sulfate (SDS) and cetyl trimethylammonium bromide (CTAB). Resistance to surfactants was evaluated by colony counts in solid media amended with critical micelle concentrations (CMC) of either surfactants, in comparison with non-amended controls. Selective cultures for surfactant-resistant bacteria were prepared in mineral medium also containing CMC concentrations of either CTAB or SDS. The surfactantresistant isolates obtained were tested by PCR for the Pseudomonas genus marker gacA gene and for the naphthalene-dioxygenase-encoding gene ndo. Isolates were also screened for biosurfactant production by the atomized oil assay. A high proportion of culturable bacterioneuston was tolerant to CMC concentrations of SDS or CTAB. The gacA-targeted PCR revealed that 64% of the isolates were Pseudomonads. Biosurfactant production in solid medium was detected in 9.4% of tested isolates, all affiliated with genus Pseudomonas. This study shows that the SML is a potential source of surfactant-resistant and biosurfactant-producing bacteria in which Pseudomonads emerge as a relevant group.

  3. Synthesis Study Of Surfactants Sodium Ligno Sulphonate (SLS From Biomass Waste Using Fourier Transform Infra Red (FTIR

    Directory of Open Access Journals (Sweden)

    Priyanto Slamet

    2018-01-01

    Full Text Available Lignin from biomass waste (Black Liquor was isolated by using sulfuric acid 25% and sodium hydroxide solutions 2N. The obtained lignin was reacted with Sodium Bisulfite to Sodium Ligno Sulfonate (SLS. The best result was achieved at 80 ° C, pH 9, ratio of lignin and bisulfite 4: 1, for 2 hours, and 290 rpm stirring rate. The result of lignin formed was sulfonated using Sodium Bisulfite (NaHSO3 to Sodium Ligno Sulfonate (SLS whose results were tested by the role of groups in peak formation by FTIR and compared to the spectrum of Sodium Ligno Sulfonate made from pure Lignin (commercial reacted with the commercial Sodium Bisulfite. The result can be seen by the typical functional groups present in the SLS.

  4. Atrazine and Diuron partitioning within a soil-water-surfactant system

    Science.gov (United States)

    Wang, P.; Keller, A.

    2006-12-01

    The interaction between pesticide and soil and water is even more complex in the presence of surfactants. In this study, batch equilibrium was employed to study the sorption of surfactants and the partitioning behaviors of Atrazine and Diuron within a soil-water-surfactant system. Five soils and four surfactants (nonionic Triton- 100, cationic Benzalkonium Chloride (BC), anionic Linear Alkylbenzenesulfonate (LAS), and anionic Sodium Dodecyl Sulfate (SDS)) were used. All surfactant sorption isotherms exhibited an initial linear increase at low surfactant concentrations but reached an asymptotic value as the surfactant concentrations increased. Among the surfactants, BC had the highest sorption onto all soils, followed by Triton-100 and then by LAS and SDS, implying that the nature of the charge significantly influences surfactant sorption. Sorption of either Triton-100 or BC was highly correlated with soil Cation Exchange Capacity (CEC) while that of LAS and SDS was complicated by the presence of Ca2+ and Mg2+ in the aqueous phase and the CEC sites. Both LAS and SDS formed complexes with Ca2+ and Mg2+, resulting in a significant decrease in the detergency of the surfactants. At high surfactant concentrations and with micelles present in the aqueous phase, the micelles formed a more competitive partitioning site for the pesticides, resulting in less pesticide sorbed to the soil. At low Triton-100 and BC concentration, the sorption of the surfactants first resulted in less Atrazine sorption but more Diuron sorption, implying competition between the surfactants and Atrazine, which serves as an indirect evidence that there is a different sorption mechanism for Atrazine. Atrazine is a weak base and it protonates and becomes positively charged near particle surfaces where the pH is much lower than in the bulk solution. The protonated Atrazine may then be held on the CEC sites via electrostatic attraction. Triton-100, LAS and SDS sorbed on the soil showed similar

  5. The adsorption of surfactant at the amorphous polymer solution interface

    International Nuclear Information System (INIS)

    Gilchrist, Valerie A.

    2001-01-01

    polymer. The area per surfactant at the cmc (A cmc ) was found to be around 50A 2 . Good agreement was obtained between SE and SNR, but the latter revealed additional information about the in-situ conformational structure of the surfactant. It was found that at the cmc, the dodecyl chain layer was only 4-5A thick, indicating that the alkyl chains lay virtually flat on PMMA surface. The ethoxylate headgroup layer was however some 16A thick, indicating the projection of the headgroups into the aqueous solution. In contrast, when anionic SDS (sodium dodecyl sulphate) and cationic C 12 TAB (dodecyl trimethyl ammonium bromide) were used, a much reduced adsorption was observed. While these results highlight the role of the type of surfactant headgroups, it shows the power of SNR and the effectiveness of the experimental approach adopted in unraveling molecular information at the interface. This experimental approach was subsequently extended to PBMA and PS for the assessment of different polymeric substrates. The varying extent of surfactant adsorption and the ingress of the surfactant associated with film swelling have clearly shown that with careful control of experimental conditions, detailed structural information can be reliably revealed from the experimental procedures that I have developed. (author)

  6. Kinetic and thermodynamic studies on the adsorption of anionic surfactant on quaternary ammonium cationic cellulose.

    Science.gov (United States)

    Zhang, Yuanzhang; Shi, Wenjian; Zhou, Hualan; Fu, Xing; Chen, Xuan

    2010-06-01

    Removal of anionic surfactants from aqueous solutions by adsorption onto quaternary ammonium cationic cellulose (QACC) was investigated. The effects of solution acidity, initial concentration, adsorption time, and temperature on the adsorption of sodium dodecyl-benzene sulfonate (SDBS), sodium lauryl sulfate (SLS), and sodium dodecyl sulfonate (SDS) were studied. The kinetic experimental data fit well with the pseudo-second-order model; the rate constant of the adsorption increased with temperature. The values of apparent activation energy for the adsorption were calculated as ranging from 10.2 to 17.4 kJ/ mol. The adsorption isotherm can be described by the Langmuir isotherm. The values of thermodynamic parameters (deltaH0, deltaS0, and deltaG0) for the adsorption indicated that this process was spontaneous and endothermic. At 318 K, the saturated adsorption capacities of QACC for SDBS, SLS, and SDS were 1.75, 1.53, and 1.39 mmol/g, respectively. The adsorption process was mainly chemisorption and partially physisorption. The results show that QACC is effective for the removal of anionic surfactants.

  7. Influence of MWCNT/surfactant dispersions on the mechanical properties of Portland cement pastes

    Science.gov (United States)

    Rodríguez, B.; Quintero, J. H.; Arias, Y. P.; Mendoza-Reales, O. A.; Ochoa-Botero, J. C.; Toledo-Filho, R. D.

    2017-12-01

    This work studies the reinforcing effect of Multi Walled Carbon Nanotubes (MWCNT) on cement pastes. A 0.35% solid concentration of MWCNT in powder was dispersed in deionized water with sodium dodecyl sulfate (cationic surfactant), cetylpyridinium chloride (anionic surfactant) and triton X-100 (amphoteric surfactant) using an ultrasonic tip processor. Three concentrations of each surfactant (1mM, 10mM and 100mM) were tested, and all samples were sonicated until an adequate dispersion degree was obtained. Cement pastes with additions of carbon nanotubes of 0.15% by mass of cement were produced in two steps; first the dispersions of MWCNT were combined with the mixing water using an ultrasonic tip processor to guarantee homogeneity, and then cement was added and mixed until a homogeneous paste was obtained. Direct tensile strength, apparent density and open porosity of the pastes were measured after 7 days of curing. It was found that the MWCNT/surfactants dispersions decrease the mechanical properties of the cement based matrix due to an increased porosity caused by the presence of surfactants.

  8. Evaluation of bacterial surfactant toxicity towards petroleum degrading microorganisms.

    Science.gov (United States)

    Lima, Tânia M S; Procópio, Lorena C; Brandão, Felipe D; Leão, Bruna A; Tótola, Marcos R; Borges, Arnaldo C

    2011-02-01

    The acute toxicity of bacterial surfactants LBBMA111A, LBBMA155, LBBMA168, LBBMA191 and LBBMA201 and the synthetic surfactant sodium dodecyl sulfate (SDS) on the bioluminescent bacterium Vibrio fischeri was evaluated by measuring the reduction of light emission (EC(20)) by this microorganism when exposed to different surfactant concentrations. Moreover, the toxic effects of different concentrations of biological and synthetic surfactants on the growth of pure cultures of isolates Acinetobacter baumannii LBBMA04, Acinetobacter junni LBBMA36, Pseudomonas sp. LBBMA101B and Acinetobacter baumanni LBBMAES11 were evaluated in mineral medium supplemented with glucose. The EC(20) values obtained confirmed that the biosurfactants have a significantly lower toxicity to V. fischeri than the SDS. After 30 min of exposure, bacterial luminescence was almost completely inhibited by SDS at a concentration of 4710 mg L(-1). Growth reduction of pure bacterial cultures caused by the addition of biosurfactants to the growth medium was lower than that caused by SDS. Copyright © 2010 Elsevier Ltd. All rights reserved.

  9. Atomistic simulations of surfactant adsorption kinetics at interfaces

    Science.gov (United States)

    Iskrenova, Eugeniya; Patnaik, Soumya

    2014-03-01

    Heat transfer control and enhancement is an important and challenging problem in a variety of industrial and technological applications including aircraft thermal management. The role of additives in nucleate boiling and phase change in general has long been recognized and studied experimentally and modeled theoretically but in-depth description and atomistic understanding of the multiscale processes involved are still needed for better prediction and control of the heat transfer efficiency. Surfactant additives have been experimentally observed to either enhance or inhibit the boiling heat transfer depending on the surfactant concentration and chemistry and, on a molecular level, their addition leads to dynamic surface tension and changes in interfacial and transfer properties, thus contributing to the complexity of the problem. We present our atomistic modeling study of the interfacial adsorption kinetics of aqueous surfactant (sodium dodecyl sulfate) systems at a range of concentrations at room and boiling temperatures. Classical molecular dynamics and Umbrella Sampling simulations were used to study the surfactant transport properties and estimate the adsorption and desorption rates at liquid-vacuum and liquid-solid interfaces. The authors gratefully acknowledge funding from AFOSR Thermal Science Program and the Air Force Research Laboratory DoD Supercomputing Resource Center for computing time and resources.

  10. Adsorption of ionic surfactants at microscopic air-water interfaces using the micropipette interfacial area-expansion method

    DEFF Research Database (Denmark)

    Kinoshita, Koji; Parra, Elisa; Needham, David

    2017-01-01

    The dynamic adsorption of ionic surfactants at air-water interfaces have been less-well studied than that of the simpler non-ionics since experimental limitations on dynamic surface tension (DST) measurements create inconsistencies in their kinetic analysis. Using our newly designed "Micropipette...... interfacial area-expansion method", we have measured and evaluated both equilibrium and dynamic adsorption of a well-known anionic surfactant, sodium dodecyl sulphate (SDS), in the absence or presence of 100mM NaCl. Our focus was to determine if and to what extent the inclusion of a new correction parameter...... for the "ideal ionic activity", A±i, can renormalize both equilibrium and dynamic surface tension measurements and provide better estimates of the diffusion coefficient of ionic surfactants in aqueous media obtained from electroneutral models, namely extended Frumkin isotherm and Ward-Tordai adsorption models...

  11. Effect of surfactant hydrophobicity on the interfacial properties of polyallylamine hydrochloride/sodium alkylsulphate at water/hexane interface

    Czech Academy of Sciences Publication Activity Database

    Sharipova, A.; Aidarova, S.; Černoch, Peter; Miller, R.

    2013-01-01

    Roč. 438, 5 December (2013), s. 141-147 ISSN 0927-7757. [EUFOAM Conference /9./. Lisbon, 08.07.2012-11.07.2012] Institutional support: RVO:61389013 Keywords : mixed adsorption layers * polymer-surfactant mixtures * water/oil interface Subject RIV: CD - Macromolecular Chemistry Impact factor: 2.354, year: 2013

  12. Influence of surfactants on the morphology of SnO{sub 2} nanocrystals prepared via a hydrothermal method

    Energy Technology Data Exchange (ETDEWEB)

    Wang Mi [State Key Laboratory of Chemical Engineering, East China University of Science and Technology, 130 Meilong Road, Shanghai 200237 (China); Shanghai Institute of Ceramics (SIC), Chinese Academy of Sciences (CAS), 1295 Dingxi Road, Shanghai 200050 (China); Gao Yanfeng, E-mail: yfgao@mail.sic.ac.cn [Shanghai Institute of Ceramics (SIC), Chinese Academy of Sciences (CAS), 1295 Dingxi Road, Shanghai 200050 (China); Dai Lei; Cao Chuanxiang [Shanghai Institute of Ceramics (SIC), Chinese Academy of Sciences (CAS), 1295 Dingxi Road, Shanghai 200050 (China); Guo Xuhong, E-mail: guoxuhong@ecust.edu.cn [State Key Laboratory of Chemical Engineering, East China University of Science and Technology, 130 Meilong Road, Shanghai 200237 (China)

    2012-05-15

    Nanoscaled SnO{sub 2} with different morphologies has been synthesized via a simple hydrothermal process at 180 Degree-Sign C using polyvinylpyrrolidone (PVP), sodium dodecyl sulfonate (SDS), cetyl trimethyl ammonium bromide (CTAB) or tetrapropyl ammonium bromide (TPAB) as surfactant. All the prepared SnO{sub 2} are of a tetragonal crystal structure. Nanocubes, nanorods, nanosheets, nanobelts and nanoparticles were prepared when changing the type and dosage of organic surfactants. It is shown that anionic surfactant (SDS) and cationic surfactant (CTAB or TPAB) at their suitable addition amounts can largely influence the morphologies of SnO{sub 2} nanocrystals. The effect is significantly dependent on the solvent types: water or ethanol. The non-ionic surfactant (PVP) can also change the morphologies like SDS but the impacts are less obvious. The effect of surfactants on the shape and size of SnO{sub 2} nanoparticles was discussed in detail. The particle growth mechanism is described based on the electrostatic interactions and Van der Waals' forces. - Graphical abstract: SnO{sub 2} nanocrystals with controllable morphologies were prepared via a hydrothermal method with surfactants. Highlights: Black-Right-Pointing-Pointer SnO{sub 2} nanocrystals were prepared via a hydrothermal method with surfactants. Black-Right-Pointing-Pointer SnO{sub 2} morphologies changed with the type and the dosage of surfactants. Black-Right-Pointing-Pointer The effect of surfactants on the growth of crystal planes was studied. Black-Right-Pointing-Pointer The controlling mechanisms of surfactants on SnO{sub 2} morphologies were discussed.

  13. Thermodynamic insights into drug-surfactant interactions: Study of the interactions of naporxen, diclofenac sodium, neomycin, and lincomycin with hexadecytrimethylammonium bromide by using isothermal titration calorimetry.

    Science.gov (United States)

    Choudhary, Sinjan; Talele, Paurnima; Kishore, Nand

    2015-08-01

    The success of drug delivery depends on the efficiency of the route of administration, which in turn relies on properties of the drug and its transport vehicle. A quantitative knowledge of association of drugs with transport vehicles is lacking when the latter are in the category of self assembled structures. The work reported in this manuscript addresses the mechanism of partitioning of naproxen, diclofenac sodium, neomycin and lincomycin in the micelles of hexadecytrimethylammonium bromide and that is quantitatively based on the measurement of thermodynamic parameters of interactions by using isothermal titration calorimetry. The addressed mechanism of partitioning is based on the identification of the type of interactions of these drugs with the surfactant micelles and monomers, along with the effect of the former on the micellization properties of the surfactant. The conclusions are based on the interpretation of the values of partitioning constant, standard molar enthalpy change, standard molar entropy change and the stoichiometry of the interaction. The results of this study have implications for deriving guidelines for the target oriented synthesis of new drugs that are to be used for effective delivery via micellar media. Copyright © 2015 Elsevier B.V. All rights reserved.

  14. Synthesis of protons exchange polymeric membranes via co-poly-esters doped with sodium dodecyl sulfate for application in PEM fuel cells; Sintese de membranas polimericas condutoras de protons por imobilizacao de MDs em copoliesteres para aplicacao em PEM-FC

    Energy Technology Data Exchange (ETDEWEB)

    Fiuza, R.A.; Brioude, M.M.; Bresciani, D.; Jose, N.M.; Boaventura, J.S. [Universidade Federal da Bahia (IQ/UFBA), Salvador, BA (Brazil). Inst. de Quimica

    2008-07-01

    Polymers are largely studied for use in PEM-type fuel cell (Proton Exchange membrane, PEMFC). These fuel cells are based on polymer membranes as electrolyte, also called protons conductor. This work developed co-polyesters made electrical conductors by doping with sodium dodecyl sulfate. The copolymers were synthesized from the copolymerization of terephthalic and adipic acids with glycerol. The material was processed in a reactor and shaped by hot pressing, yielding homogeneous and flexible plates, with excellent surface finish. The co-polyesters were analyzed by SEM, FTIR, TG, DSC, and XRD. The thermal analysis showed that the composites were thermally stable up to about 250 deg C. The micrographics revealed the MDS homogeneously dispersed in the polymeric matrix. These copolymers showed electrical conductivity between 10-7 to 10-1 S/cm, suggesting strong potential use in PEM fuel cells. (author)

  15. ZnO nanoparticles synthesized by polyol method: Influence of surfactant and molarity of zinc salt

    International Nuclear Information System (INIS)

    Abdul Halim Abdullah; Lee, Ek Giat; Zulkarnain Zainal; Mohd Zobir Hussein

    2009-01-01

    Full text: Zinc oxide (ZnO) nanoparticles have been synthesized via polyol method using zinc acetate as zinc salt in the presence of diethylene glycol. The influences of different types of surfactants (sodium dodecyl sulphate, tetrabutylammonium bromide and polyvinylpyrrolidone) and molarity of zinc salt on the shape and particle sizes of synthesized ZnO have been carried out. The synthesized ZnO were characterized by using X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM). Among the surfactants used, poly vinylpyrolidone (PVP) is found to be the most effective in controlling particle size. Amount of zinc salt added to the solution also caused slightly changes in shape of ZnO. (author)

  16. Evaluation of the interaction of surfactants with stratum corneum model membrane from Bothrops jararaca by DSC.

    Science.gov (United States)

    Baby, André Rolim; Lacerda, Aurea Cristina Lemos; Velasco, Maria Valéria Robles; Lopes, Patrícia Santos; Kawano, Yoshio; Kaneko, Telma Mary

    2006-07-06

    The interaction of surfactants sodium dodecyl sulfate (SDS), cetyl trimethyl ammonium chloride (CTAC) and lauryl alcohol ethoxylated (12 mol ethylene oxide) (LAE-12OE) was evaluated on the stratum corneum (SC) of shed snake skins from Bothrops jararaca, used as model membrane, and thermal characterized by differential scanning calorimetry (DSC). Surfactant solutions were employed above of the critical micellar concentration (CMC) with treatment time of 8h. The SDS interaction with the SC model membrane has increased the characteristic transition temperature of 130 degrees C in approximately 10 degrees C for the water loss and keratin denaturation, indicating an augmentation of the water content. Samples treated with CTAC have a decrease of the water loss temperature, while, for the LAE-12OE treated samples, changes on the transition temperature have not been observed.

  17. Adsorption of anionic surfactant on porous and nonporous polyethylene terephthalate films

    International Nuclear Information System (INIS)

    Yamauchi, Yu.; Apel, P.Yu.

    2016-01-01

    We study the adsorption of anionic surfactant, sodium dodecyl diphenyloxide disulfonate (SDDD) on three types of polyethylene terephthalate (PET) substrates from aqueous solutions of SDDD of different concentrations. Neutral electrolyte (KCl) was added to the solutions to vary the ionic strength. Three types of substrates were used: 1) original PET film; 2) etched nonporous film, obtained from pristine film by chemical etching and bearing negative charge on the surface; 3) etched porous membranes, fabricated from pristine film by ion irradiation and subsequent chemical etching. The membranes have negative charge on the flat surface and on the inner pore walls. The comparison shows that the negative charge on the flat surface has weak effect on adsorption of the anionic surfactant, and the SDDD adsorption on the inner walls of pores is much weaker than on flat surface, even if the pore radius is significantly larger than the Debye length. This «exclusion» effect strongly depends on ionic strength of solution. [ru

  18. Effect of Presence and Concentration of Plasticizers, Vegetable Oils, and Surfactants on the Properties of Sodium-Alginate-Based Edible Coatings

    Directory of Open Access Journals (Sweden)

    Tugce Senturk Parreidt

    2018-03-01

    Full Text Available Achieving high quality of a coated food product is mostly dependent on the characteristics of the food material to be coated, the properties of the components in the coating solution, and the obtained coating material. In the present study, usability and effectiveness of various components as well as their concentrations were assessed to produce an effective coating material. For this purpose, different concentrations of gelling agent (sodium alginate 0–3.5%, w/w, plasticizers (glycerol and sorbitol (0–20%, w/w, surfactants (tween 40, tween 80, span 60, span 80, lecithin (0–5%, w/w, and vegetable oils (sunflower oil, olive oil, rapeseed oil (0–5%, w/w were used to prepare edible coating solutions. Formulations were built gradually, and characteristics of coatings were evaluated by analyzing surface tension values and its polar and dispersive components, emulsion droplet size, and optical appearance in microscopic scale. The results obtained showed that 1.25% sodium alginate, 2% glycerol, 0.2% sunflower oil, 1% span 80, and 0.2% tween 40 or tween 80 can be used in formulation to obtain an effective coating for hydrophobic food surfaces. Three formulations were designed, and their stability (emulsion droplet size, optical characteristics, and creaming index and wettability tests on strawberry showed that they could be successfully used in coating applications.

  19. Mixed Micelle System Produced by Interaction Between Transglycosylated Stevia and an Ionic Surfactant Improves Dissolution Profile of Mefenamic Acid.

    Science.gov (United States)

    Fujimori, Miki; Kadota, Kazunori; Tozuka, Yuichi

    2017-04-01

    Transglycosylated stevia (stevia-G) can effectively improve the dissolution and bioavailability of poorly water-soluble drugs. Furthermore, addition of an ionic surfactant to stevia-G solution has been shown to enhance the dissolution effect of stevia-G on flurbiprofen. Herein, 4 surfactants, namely sodium dodecyl sulfate, sodium N-dodecanoylsarcosinate, sodium monododecyl phosphate, and lauryltrimethylammonium chloride (LTAC) were screened to investigate their synergistic effect with stevia-G in enhancing the solubility of mefenamic acid (MFA). The ternary formulation containing LTAC produced the highest increase in solubility, whereas the binary MFA/LTAC formulation did not increase the solubility of MFA. Surface tension was evaluated to analyze the interaction between stevia-G and each ionic surfactant, wherein the Rubingh model was applied to predict mixed micelle formation between stevia-G and LTAC. Interaction parameters calculated by the Rubingh model reflected mixed micelle formation between stevia-G and LTAC relative to the self-interactions of the 2 individual surfactants. All interaction parameters in this system showed negative values, indicating a favorable interaction (e.g., hydrogen bond or electrostatic and dipole) between binary components in the mixed micelles. Spray-dried particles of ternary formulations (MFA/stevia-G/LTAC) were prepared to evaluate the dissolution profile and physicochemical properties. Dissolution profiling showed that the concentration of MFA released from spray-dried particles was significantly higher than untreated MFA. Copyright © 2017 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

  20. Atypical effects of incorporated surfactants on stability and dissolution properties of amorphous polymeric dispersions.

    Science.gov (United States)

    Al-Obaidi, Hisham; Lawrence, M Jayne; Buckton, Graham

    2016-11-01

    To understand the impact of ionic and non-ionic surfactants on the dissolution and stability properties of amorphous polymeric dispersions using griseofulvin (GF) as a model for poorly soluble drugs. Solid dispersions of the poorly water-soluble drug, griseofulvin (GF) and the polymers, poly(vinylpyrrolidone) (PVP) and poly(2-hydroxypropyl methacrylate) (PHPMA), have been prepared by spray drying and bead milling and the effect of the ionic and non-ionic surfactants, namely sodium dodecyl sulphate (SDS) and Tween-80, on the physico-chemical properties of the solid dispersions studied. The X-ray powder diffraction data and hot-stage microscopy showed a fast re-crystallisation of GF. While dynamic vapour sorption (DVS) measurements indicated an increased water uptake, slow dissolution rates were observed for the solid dispersions incorporating surfactants. The order by which surfactants free dispersions were prepared seemed critical as indicated by DVS and thermal analysis. Dispersions prepared by milling with SDS showed significantly better stability than spray-dried dispersions (drug remained amorphous for more than 6 months) as well as improved dissolution profile. We suggest that surfactants can hinder the dissolution by promoting aggregation of polymeric chains, however that effect depends mainly on how the particles were prepared. © 2016 Royal Pharmaceutical Society.

  1. Evaluation of acute and chronic toxicity of DSS and LAS surfactants undergoing the irradiation with electron beam

    International Nuclear Information System (INIS)

    Romanelli, Maria Fernanda

    2004-01-01

    Surfactants are synthetic organic compounds widely used in cosmetic, food, textile, dyers and paper production industries and in particular detergents and others cleaning products industries. The world consumption is nearly 8 million tons per year. One of the main environmental issues coming from the use of these compounds is their toxicity that compromises the biological treatment of effluents and the quality of receiving waters. The objective of this work was the application of ionizing radiation by electron beam in the degradation and reduction of acute and chronic toxicities of surfactants sodium dodecylsulfate (SDS), dodecyl p-benzenesulfonate acid (LAS) and sodium dodecyl p-benzenesulfonate (LAS). This treatment technology has been studied as a pre-treatment for effluents containing toxic and non-biodegradable compounds, before the biological treatment. Two acute toxicity assays were employed, one with the micro-crustacean Daphnia similis and the other with the luminescent bacterium Vibrio fischeri along with a chronic toxicity assay with the micro-crustacean Ceriodaphnia dubia (just for SDS and acid LAS) for the non-irradiated and irradiated samples and radiation doses 3.0 kGy, 6.0 kGy, 9.0 kGy and 12.0 kGy. Physical-chemical parameters were evaluated for the following up the degradation of the surfactant molecules. The reductions of acute toxicity varied between 72.49% and 90.98% for SDS, 18.22% and 78.98% for acid LAS and 82.66% and 94.26% for sodium LAS. For the chronic toxicity, the reduction percentages varied between 64.03% and 83.01% for SDS and 47.48% and 64.91% for acid LAS. When one considers the application of the electron beam as a pre-treatment of effluents containing high concentrations of surfactants, the toxicity is an essential parameter allowing the further biological treatment of these effluents. (author)

  2. Formulation and physiochemical study of α-tocopherol based oil in water nanoemulsion stabilized with non toxic, biodegradable surfactant: Sodium stearoyl lactate.

    Science.gov (United States)

    Kaur, Khushwinder; Kaur, Jaspreet; Kumar, Raj; Mehta, S K

    2017-09-01

    The unique properties such as high optical clarity, stability and enhanced bioavailability of nanoemulsion make them useful for food, cosmetic and pharmaceutical industries. In this work, sodium stearoyl lactate and Tween 80 surfactants were collectively used to fabricate alpha tocopherol based oil in water nanoemulsion using high energy ultrasonication method. The spherical nature of pure and drug loaded nanoemulsion has been confirmed with transmission electron microscopy (TEM). The influence of pH, dilution, surfactant concentration and ionic strength on average particle size of pure and nutraceutical (benzylisothiocyanate and curcumin) encapsulated emulsion was examined. The prepared emulsion exhibited good stability up to 90days in salt solution (50-200mM) and different pH conditions. The cumulative release % of benzylisothiocyanate and curcumin was found to be 50.29% in 36h and 89.15% in 150h respectively. The antioxidant activity of pure, benzylisothiocyanate, curcumin and cocktail (benzylisothiocyanate and curcumin) nanoemulsion was calculated with 2,2-diphenyl-1-picrylhydrazyl radical. The IC 50 value of different antioxidant showed that benzylisothiocyanate nanoemulsion acted as better antioxidant as compared to pure and curcumin encapsulated nanoemulsion. Also the cell viability of pure nanoemulsion was found to be 24% on hep G2 cell. The effect of UV light irradiation on curcumin and benzylisothiocyanate stability was carried out in different solvent conditions (water/ethanol and nanoemulsion). The degradation of curcumin by the impact of UV light was successfully controlled by trapping in NEm. Copyright © 2016 Elsevier B.V. All rights reserved.

  3. Surfactant mediated slurry formulations for Ge CMP applications

    KAUST Repository

    Basim, G. Bahar

    2013-01-01

    In this study, slurry formulations in the presence of self-assembled surfactant structures were investigated for Ge/SiO2 CMP applications in the absence and presence of oxidizers. Both anionic (sodium dodecyl sulfate-SDS) and cationic (cetyl trimethyl ammonium bromide-C12TAB) micelles were used in the slurry formulations as a function of pH and oxidizer concentration. CMP performances of Ge and SiO2 wafers were evaluated in terms of material removal rates, selectivity and surface quality. The material removal rate responses were also assessed through AFM wear rate tests to obtain a faster response for preliminary analyses. The surfactant adsorption characteristics were studied through surface wettability responses of the Ge and SiO2 wafers through contact angle measurements. It was observed that the self-assembled surfactant structures can help obtain selectivity on the silica/germanium system at low concentrations of the oxidizer in the slurry. © 2013 Materials Research Society.

  4. sodium

    International Development Research Centre (IDRC) Digital Library (Canada)

    Les initiatives de réduction de la consommation de sel qui visent l'ensemble de la population et qui ciblent la teneur en sodium des aliments et sensibilisent les consommateurs sont susceptibles de réduire la consommation de sel dans toutes les couches de la population et d'améliorer la santé cardiovasculaire. Ce projet a ...

  5. Structural analysis of protein complexes with sodium alkyl sulfates by small-angle scattering and polyacrylamide gel electrophoresis.

    Science.gov (United States)

    Ospinal-Jiménez, Mónica; Pozzo, Danilo C

    2011-02-01

    Small-angle X-ray (SAXS) and neutron (SANS) scattering is used to probe the structure of protein-surfactant complexes in solution and to correlate this information with their performance in gel electrophoresis. Proteins with sizes between 6.5 to 116 kDa are denatured with sodium alkyl sulfates (SC(x)S) of variable tail lengths. Several combinations of proteins and surfactants are analyzed to measure micelle radii, the distance between micelles, the extension of the complex, the radius of gyration, and the electrophoretic mobility. The structural characterization shows that most protein-surfactant complexes can be accurately described as pearl-necklace structures with spherical micelles. However, protein complexes with short surfactants (SC(8)S) bind with micelles that deviate significantly from spherical shape. Sodium decyl (SC(10)S) and dodecyl (SC(12)S, more commonly abbreviated as SDS) sulfates result in the best protein separations in standard gel electrophoresis. Particularly, SC(10)S shows higher resolutions for complexes of low molecular weight. The systematic characterization of alkyl sulfate surfactants demonstrates that changes in the chain architecture can significantly affect electrophoretic migration so that protein-surfactant structures could be optimized for high resolution protein separations.

  6. Surfactant-dependent macrophage response to polypyrrole-based coatings electrodeposited on Ti6Al7Nb alloy

    Energy Technology Data Exchange (ETDEWEB)

    Mindroiu, Mihaela [University Polytechnica of Bucharest, Faculty of Applied Chemistry and Materials Science, 1-7 Polizu, 011061, Bucharest (Romania); Ion, Raluca [University of Bucharest, Department of Biochemistry and Molecular Biology, 91-95 Spl. Independentei, 050095, Bucharest (Romania); Pirvu, Cristian [University Polytechnica of Bucharest, Faculty of Applied Chemistry and Materials Science, 1-7 Polizu, 011061, Bucharest (Romania); Cimpean, Anisoara, E-mail: anisoara.cimpean@bio.unibuc.ro [University of Bucharest, Department of Biochemistry and Molecular Biology, 91-95 Spl. Independentei, 050095, Bucharest (Romania)

    2013-08-01

    In this study, polypyrrole (PPy) films were successfully synthesized on Ti6Al7Nb alloy by potentiostatic polymerization in the presence of poly(sodium 4-styrenesulfonate) (NaPSS), t-octylphenoxy polyethoxyethanol (Triton X-100) and N-dodecyl-β-D-maltoside (DM) surfactants. Atomic force microscopy (AFM) analysis of the PPy/surfactant composite films revealed a granular structure characterized by a lower surface roughness than un-modified PPy films. The results demonstrated that addition of surfactants, namely Triton X-100 and DM, can improve electrochemical film stability and corrosion resistance. Further, Triton X-100 enhanced the adhesive strength of PPy films to the substrate. The surfactant type also showed a great influence on the surface wettability, the highest hydrophilic character being observed in the case of PPy/PSS film. Few studies have been devoted to the elucidation of inflammatory cell response to PPy-based materials. Therefore, RAW 264.7 macrophages were cultured on PPy-surfactant films to determine whether they elicit a differential cell behavior in terms of cell adhesion, proliferation, cellular morphology and cytokine secretion. Our results highlight the dependence of macrophage response on the surfactants used in the pyrrole polymerization process and suggest that the immune response to biomaterials coated with PPy films might be controlled by the choice of surfactant molecules. Highlights: • We electrodeposited polypyrrole films on Ti6Al7Nb alloy using three surfactants. • Differences in electrostability and wettability of polypyrrole films were found. • Triton X increased and NaPSS decreased the adhesion of polypyrrole films to Ti6Al7Nb. • Cytoskeletal architecture and macrophage activation were affected by surfactants. • The hydrophilic PPy/PSS coating elicited the lowest inflammatory response.

  7. Surfactant-dependent macrophage response to polypyrrole-based coatings electrodeposited on Ti6Al7Nb alloy

    International Nuclear Information System (INIS)

    Mindroiu, Mihaela; Ion, Raluca; Pirvu, Cristian; Cimpean, Anisoara

    2013-01-01

    In this study, polypyrrole (PPy) films were successfully synthesized on Ti6Al7Nb alloy by potentiostatic polymerization in the presence of poly(sodium 4-styrenesulfonate) (NaPSS), t-octylphenoxy polyethoxyethanol (Triton X-100) and N-dodecyl-β-D-maltoside (DM) surfactants. Atomic force microscopy (AFM) analysis of the PPy/surfactant composite films revealed a granular structure characterized by a lower surface roughness than un-modified PPy films. The results demonstrated that addition of surfactants, namely Triton X-100 and DM, can improve electrochemical film stability and corrosion resistance. Further, Triton X-100 enhanced the adhesive strength of PPy films to the substrate. The surfactant type also showed a great influence on the surface wettability, the highest hydrophilic character being observed in the case of PPy/PSS film. Few studies have been devoted to the elucidation of inflammatory cell response to PPy-based materials. Therefore, RAW 264.7 macrophages were cultured on PPy-surfactant films to determine whether they elicit a differential cell behavior in terms of cell adhesion, proliferation, cellular morphology and cytokine secretion. Our results highlight the dependence of macrophage response on the surfactants used in the pyrrole polymerization process and suggest that the immune response to biomaterials coated with PPy films might be controlled by the choice of surfactant molecules. Highlights: • We electrodeposited polypyrrole films on Ti6Al7Nb alloy using three surfactants. • Differences in electrostability and wettability of polypyrrole films were found. • Triton X increased and NaPSS decreased the adhesion of polypyrrole films to Ti6Al7Nb. • Cytoskeletal architecture and macrophage activation were affected by surfactants. • The hydrophilic PPy/PSS coating elicited the lowest inflammatory response

  8. Effect of various surfactants (cationic, anionic and non-ionic) on the growth of Aspergillus parasiticus (NRRL 2999) in relation to aflatoxin production.

    Science.gov (United States)

    Tanuja, Kosuri; Hemalatha, K; Karuna, Rupula; Sashidhar Rao, B

    2010-08-01

    The effect of surfactants (two cationic, one anionic and three non-ionic) at 0.001, 0.01, 0.1 and 1.0 % concentrations on aflatoxin production, ergosterol content and sugar consumption by Aspergillus parasiticus (NRRL 2999) in YES liquid culture medium is reported. At 0.01% concentration, the cationic surfactants, cetyl dimethyl ammonium bromide (CDAB) and dodecyl trimethyl ammonium bromide (DTAB), and the anionic surfactant, sodium dodecyl sulfate (SDS), completely inhibited spore germination, while DTAB also inhibited the production of ergosterol and toxin (p lauryl ether (Brij-35) and ethoxylated p-tert-octylphenol (Triton X-100) delayed the spore germination up to day 5 at all concentrations and inhibited toxin and ergosterol production at 0.001% concentration. The affect was found to be dose-dependent from 0.001% to 1%, for Triton X-100 only. Positive correlation between ergosterol content and toxin production in the presence of different surfactants at various time periods (3, 5, 7, 9 and 12 days) was found. Tween-20 was most effective in inhibiting toxin production on day 7, when aflatoxin production was found to be maximal in control group. Sugar consumption was directly proportional to the ergosterol content, showing a significant correlation with aflatoxin production.

  9. An electronic spectroscopic study of micellisation of surfactants and solvation of homomicelles formed by cationic or anionic surfactants using a solvatochromic electron donor acceptor dye.

    Science.gov (United States)

    Kedia, Niraja; Sarkar, Amrita; Purkayastha, Pradipta; Bagchi, Sanjib

    2014-10-15

    Solvatochromic absorption and fluorescence bands of a donor-acceptor dye have been utilised for following the micellisation and for probing the polarity of the aqueous homomicellar phase provided separately by cationic (cetyltrimethylammonimum bromide, CTAB and dodecyltrimethylammonimum bromide, DTAB) and anionic (sodium dodecyl sulphate, SDS) surfactant. Results indicate that for a low concentration of surfactant (below cmc) the dye forms a dimer in aqueous solution. In a micellar media, however, the dye exists as monomers. A strong dye-micelle interaction, as indicated by the shift of the solvatochromic intramolecular charge transfer band of the dye, has also been indicated. The absorption and fluorescence parameters of the dye have been utilised for studying the onset of aggregation of the surfactants. An iterative procedure has been developed for the estimation of cmc and the distribution coefficient (KD) of the dye between the aqueous and the micellar phase. All the parameters provide convergent values of cmc. A high value of KD indicates that the dye exists predominantly in the micellar phase. The solvatochromic parameters characterising the dipolarity-polarisability (π(*)) and H-bond donation ability (α) of modes of solvation interaction in different micellar media have been estimated. The dye is found to distribute itself between two regions in a catanionic vesicle formed by surfactants SDS and DTAB, one being relatively polar than other. The distribution coefficients have been found out using the fluorescence data. Copyright © 2014 Elsevier B.V. All rights reserved.

  10. Surfactant and heavy metal interaction in poplar: a focus on SDS and Zn uptake.

    Science.gov (United States)

    Pierattini, Erika C; Francini, Alessandra; Raffaelli, Andrea; Sebastiani, Luca

    2018-01-01

    Surfactants are widely used detergent ingredients and, thanks to their chemical properties, they are applied for remediation of sites polluted by heavy metals and organic contaminants, both in soil flushing and in phytoremediation. However, their direct effects on tree physiology especially in consociation with heavy metal pollution, as well as their possible absorption by plants, have not been appropriately investigated. In order to evaluate plant uptake/translocation of the surfactant sodium dodecyl sulfate (SDS) and the heavy metal zinc (Zn) in Populus alba L. Villafranca clone, SDS was applied alone (0.5 mM) or in combination with Zn (1 mM). Physiological effects on plant growth and photosynthetic performance were investigated. An increasing trend of Zn translocation towards basal leaves as a consequence of SDS co-treatment (1 mM Zn + 0.5 mM SDS; P = 0.03) was observed, proving the ability of SDS to improve heavy metals translocation. However, SDS exposure (both in 0.5 mM SDS and 1 mM Zn + 0.5 mM SDS treated plants) resulted in the appearance of foliar necrosis that expanded with an acropetal trend and finally led to leaf abscission. This phenotype may be caused by the emergence of an additional stress during the experimental trial, which could be related to the dissociation of sodium (Na) ions from the dodecyl sulfate molecules in the hydroponic system. In fact, while liquid chromatography-tandem mass spectrometry measurements revealed that dodecyl sulfate is mainly retained at root levels, Na is translocated to the aerial parts of the plant. © The Author 2017. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  11. Antimicrobial Activity of Single-Walled Carbon Nanotubes Suspended in Different Surfactants

    Directory of Open Access Journals (Sweden)

    Lifeng Dong

    2012-01-01

    Full Text Available We investigated the antibacterial activity of single-walled carbon nanotubes (SWCNTs dispersed in surfactant solutions of sodium cholate, sodium dodecylbenzene sulfonate, and sodium dodecyl sulfate. Among the three surfactants, sodium cholate demonstrated the weakest antibacterial activity against Salmonella enterica, Escherichia coli, and Enterococcus faecium and thereby was used to disperse bundled SWCNTs in order to study nanotube antibiotic activity. SWCNTs exhibited antibacterial characteristics for both S. enterica and E. coli. With the increase of nanotube concentrations from 0.3 mg/mL to 1.5 mg/mL, the growth curves had plateaus at lower absorbance values whereas the absorbance value was not obviously affected by the incubation ranging from 5 min to 2 h. Our findings indicate that carbon nanotubes could become an effective alternative to antibiotics in dealing with drug-resistant and multidrug-resistant bacterial strains because of the physical mode of bactericidal action that SWCNTs display.

  12. Photoinduced electron transfer reaction in polymer-surfactant aggregates: Photoinduced electron transfer between N,N-dimethylaniline and 7-amino coumarin dyes

    International Nuclear Information System (INIS)

    Chakraborty, Anjan; Seth, Debabrata; Setua, Palash; Sarkar, Nilmoni

    2008-01-01

    Photoinduced electron transfer between coumarin dyes and N,N-dimethylaniline has been investigated by using steady state and picosecond time resolved fluorescence spectroscopy in sodium dodecyl sulphate (SDS) micelles and PVP-polyvinyl pyrrolidone (SDS) polymer-surfactant aggregates. A slower rate of electron transfer is observed in PVP-SDS aggregates than in polymer-free SDS micelles. A Marcus type inversion is observed in the correlation of free energy change in comparison with the electron transfer rate. The careful investigation reveals that C-151 deviates from the normal Marcus inverted region compared to its analogs C-152 and C-481 due to slower rotational relaxation and smaller translational diffusion coefficient

  13. Acidity Constants Determination of Triazine Dye Derivative in the presence of some Surfactants by Multiwavelength Spectrophotometric and Spectrofluorimetric

    Directory of Open Access Journals (Sweden)

    Ali Yeganeh Faal

    2014-03-01

    Full Text Available In this work, acidity constants protonated form of 4.4'-bis astilbene-2,2'-disulfonic-disodium salts (TRIAZ have been determined spectrophotometrically and spectrofluorimetrically at 25◦C and ionic strength of 0.1M KNO3. A program based on MCR-ALS applied for determination of acidity constants. The results show that the peak values of dye are influenced by the presence of anionic, cationic, and nonionic surfactants. The effects of sodium dodecyl sulfate (SDS, Triton X-100 (TX-100 and cetyl trimethyl ammonium bromide (CTAB as a surface-active agent on the acidic and basic forms, and the spectral properties of dye were studied. Also, we determined the critical micelle concentration (CMC for these surfactants by spectrophotometric and spectrofluorimetric triazine dye probes. In addition, by using of evolving factor analysis (EFA and multivariate curve resolution alternative least squares (MCR-ALS methods, acidity constants were acquired.

  14. Ion-Selective Electrode for Anionic Surfactants Using Hexadecyl Trimethyl Ammonium Bromide-Sodium Dodecylsulfate as an Active Ionophore

    Directory of Open Access Journals (Sweden)

    Junwei Wang

    2011-01-01

    Full Text Available The construction and characteristic performance of PVC membrane electrode responsive to sodium dodecylsulfate (SDS are described in this paper. The electrode is based on hexadecyl trimethyl ammonium bromide-Sodium dodecylsulfate (CTA+DS− ion pair as ionophore in PVC membrane, which displays a Nernstian slope of −58 ± 0.9 mV/decade in a 5.0 × 10−6 to 2.5 × 10−3 mol L−1 concentration range and a limit of detection of 2.9 × 10−6 mol L−1. The electrode can be used for 3 months without showing significant changes in the value of slope or working range. Also the electrode has wide pH range of application and short response time. The electrode shows a selective response to SDS and a poor response to common inorganic anions. The selective sequence found was SDS > HCO3 − > CH3COO− > Cl− > I− > NO3 −≈ Br− > F− > CO3 2− > C6H5O7 3− > C2O4 2− > SO4 2− > C4H4O6 2− > SO3 2− > PO4 3−. The potentiometric selectivity coefficients determined are indicating that common anions would not interfere in the SDS determination. The electrode has been utilized as an end point indicator electrode for potentiometric titration involving hyamine as titrant.

  15. Degradation of soil-sorbed trichloroethylene by stabilized zero valent iron nanoparticles: Effects of sorption, surfactants, and natural organic matter

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Man [Auburn University, Auburn, Alabama; He, Feng [ORNL; Zhao, Dongye [Auburn University, Auburn, Alabama; Hao, Xiaodi [Beijing University of Civil Engineering and Architecture

    2011-01-01

    Zero valent iron (ZVI) nanoparticles have been studied extensively for degradation of chlorinated solvents in the aqueous phase, and have been tested for in-situ remediation of contaminated soil and groundwater. However, little is known about its effectiveness for degrading soil-sorbed contaminants. This work studied reductive dechlorination of trichloroethylene (TCE) sorbed in two model soils (a potting soil and Smith Farm soil) using carboxymethyl cellulose (CMC) stabilized Fe-Pd bimetallic nanoparticles. Effects of sorption, surfactants and dissolved organic matter (DOC) were determined through batch kinetic experiments. While the nanoparticles can effectively degrade soil-sorbed TCE, the TCE degradation rate was strongly limited by desorption kinetics, especially for the potting soil which has a higher organic matter content of 8.2%. Under otherwise identical conditions, {approx}44% of TCE sorbed in the potting soil was degraded in 30 h, compared to {approx}82% for Smith Farm soil (organic matter content = 0.7%). DOC from the potting soil was found to inhibit TCE degradation. The presence of the extracted SOM at 40 ppm and 350 ppm as TOC reduced the degradation rate by 34% and 67%, respectively. Four prototype surfactants were tested for their effects on TCE desorption and degradation rates, including two anionic surfactants known as SDS (sodium dodecyl sulfate) and SDBS (sodium dodecyl benzene sulfonate), a cationic surfactant hexadecyltrimethylammonium (HDTMA) bromide, and a non-ionic surfactant Tween 80. All four surfactants were observed to enhance TCE desorption at concentrations below or above the critical micelle concentration (cmc), with the anionic surfactant SDS being most effective. Based on the pseudo-first-order reaction rate law, the presence of 1 x cmc SDS increased the reaction rate by a factor of 2.5 when the nanoparticles were used for degrading TCE in a water solution. SDS was effective for enhancing degradation of TCE sorbed in Smith Farm

  16. Shifts in microbial community structure during in situ surfactant-enhanced bioremediation of polycyclic aromatic hydrocarbon-contaminated soil.

    Science.gov (United States)

    Wang, Lingwen; Li, Feng; Zhan, Yu; Zhu, Lizhong

    2016-07-01

    This study aims to reveal the microbial mechanism of in situ surfactant-enhanced bioremediation (SEBR). Various concentrations of rhamnolipids, Tween 80, and sodium dodecyl benzenesulfonate (SDBS) were separately sprayed onto soils contaminated with polycyclic aromatic hydrocarbons (PAHs) for years. Within 90 days, the highest level of degradation (95 %) was observed in the soil treated with rhamnolipids (10 mg/kg), followed by 92 % degradation with Tween 80 (50 mg/kg) and 90 % degradation with SDBS (50 mg/kg). The results of the microbial phospholipid fatty acids (PLFAs) suggest that bacteria dominated the enhanced PAH biodegradation (94 % of the maximum contribution). The shift of bacterial community structure during the surfactant treatment was analyzed by using the 16S rRNA gene high-throughput sequencing. In the presence of surfactants, the number of the operational taxonomic units (OTUs) associated with Bacillus, Pseudomonas, and Sphingomonas increased from 2-3 to 15-30 % at the end of the experiment (two to three times of control). Gene prediction with phylogenetic investigation of communities by reconstruction of unobserved states (PICRUSt) shows that the PAH-degrading genes, such as 1-hydroxy-2-naphthoate dioxygenase and PAH dioxygenase large subunit, significantly increased after the surfactant applications (p < 0.05). The findings of this study provide insights into the surfactant-induced shifts of microbial community, as well as critical factors for efficient bioremediation.

  17. Rheological Study on ATBS-AM Copolymer-Surfactant System in High-Temperature and High-Salinity Environment

    Directory of Open Access Journals (Sweden)

    Muhammad Shahzad Kamal

    2013-01-01

    Full Text Available Experimental studies were conducted to evaluate the rheological properties of surfactant-polymer (SP system. This SP system consists of a copolymer of acrylamide (AM and acrylamido tertiary butyl sulfonate (ATBS and sodium dodecyl sulphate (SDS surfactant. Effects of surfactant concentration, temperature, polymer concentration, and salinity on rheological properties of SP system were investigated by means of oscillation and shear measurements. Comparison with classical partially hydrolyzed polyacrylamide (HPAM was made. For the same temperature range, the viscosity drop for HPAM was about four times higher than the viscosity drop for ATBS-AM copolymer. In deionized water, viscosity of both polymers and SP systems was very high as compared to viscosity in saline water. Viscosity reduction of ATBS-AM copolymer was higher for salts having divalent cations. The SP system showed precipitation in presence of divalent cations. It worked well with monovalent cations even at relatively high salinities. The addition of 0.1% surfactant to the polymer resulted in a 60% decrease in the viscosity. Some interfacial rheological experiments were also carried out to investigate the behaviors on the interface between SP solutions and oil. Addition of 0.1% surfactant showed a 65% decrease in G′ at SP solution-oil interface. SP system consisting of ATBS-AM and SDS showed better performance at high temperature compared to HPAM-SDS system. Due to precipitation, the SP system should be restricted to environment having low divalent cations.

  18. Role of anionic and cationic surfactants on the structural and dielectric properties of ZrO{sub 2} nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Sidhu, Gaganpreet Kaur; Kumar, Rajesh, E-mail: rajeshbaboria@gmail.com

    2017-01-15

    Highlights: • Synthesis of Zirconia nanoparticles with and without surfactants by co- precipitation method. • Surface modification of ZrO{sub 2} nanoparticles. • Phase transition with different concentration of surfactants. • Dielectric behavior of bare, CTAB assisted and SDS assisted ZrO{sub 2} nanoparticles. - Abstract: In the present paper, we report the synthesis of Cetyltrimethylammonium Bromide (CTAB) and Sodium dodecyl sulfate (SDS) assisted Zirconia (ZrO{sub 2}) nanoparticles by co-precipitation method. The effect of surfactant concentration on the structural and dielectric properties has been extensively studied. X-ray diffraction studies reveal the formation of tetragonal phase in the ZrO{sub 2} nanoparticles prepared by lower CTAB concentration. However, for higher concentration of CTAB some traces of monoclinic phase appeared along with tetragonal phase. SDS assisted nanoparticles shows crystalline tetragonal phase with lower concentration of SDS and amorphous nature with higher concentrations of SDS. FTIR results show the presence of Zr–O symmetrical stretching vibrations at tetrahedral site. The dielectric properties of all samples have been studied from 10 Hz to 1 MHz, revealing the low value of dielectric constant with CTAB and very high value with SDS as compared to bare ZrO{sub 2} nanoparticles. The dielectric behaviour of the bare and surfactant assisted nanoparticles has been correlated with the phase transition, size of nanoparticles and the nature of surfactants.

  19. Synergistic effect of hydrotrope and surfactant on solubility and dissolution of atorvastatin calcium: screening factorial design followed by ratio optimization.

    Science.gov (United States)

    Patel, V F; Sarai, J

    2014-01-01

    The present study was aimed at investigating the effect of hydrotrope and surfactant on poor solubility of atorvastatin calcium. Excipients screening followed by factorial design was performed to study effect of excipients and manufacturing methods on solubility of drug. Three independent factors (carrier, surfactant and manufacturing method) were evaluated at two levels using solubility as a dependant variable. Solid-state characterisation was performed using Fourier transform infrared spectroscopy and differential scanning calorimetry. Optimised complex were incorporated into orally disintegrating micro tablets and in vitro dissolution test was performed. Nicotinamide, Plasdone and sodium dodecyl sulphate were emerged as promising excipients from excipient screening. General regression analysis revealed only the type of carrier has significantly enhanced (P<0.05) the solubility of drug while other factors were found to be nonsignificant. Ratio optimisation trial revealed that drug to nicotinamide ratio is more critical in enhancing the solubility of drug (40 fold increases in solubility compared to pure drug) in comparison to drug-surfactant ratio; however the presence of surfactant deemed essential. Significantly higher rate and extent of dissolution was observed from solid dispersion complex and tablets compared to dissolution of pure drug (P<0.05). Study revealed hydrotrope and surfactant have synergistic effect on solubility and dissolution of atorvastatin calcium and this can be explored further.

  20. Electrostatic Screening and Charge Correlation Effects in Micellization of Ionic Surfactants

    KAUST Repository

    Jusufi, Arben

    2009-05-07

    We have used atomistic simulations to study the role of electrostatic screening and charge correlation effects in self-assembly processes of ionic surfactants into micelles. Specifically, we employed grand canonical Monte Carlo simulations to investigate the critical micelle concentration (cmc), aggregation number, and micellar shape in the presence of explicit sodium chloride (NaCl). The two systems investigated are cationic dodecyltrimethylammonium chloride (DTAC) and anionic sodium dodecyl sulfate (SDS) surfactants. Our explicit-salt results, obtained from a previously developed potential model with no further adjustment of its parameters, are in good agreement with experimental data for structural and thermodynamic micellar properties. We illustrate the importance of ion correlation effects by comparing these results with a Yukawa-type surfactant model that incorporates electrostatic screening implicitly. While the effect of salt on the cmc is well-reproduced even with the implicit Yukawa model, the aggregate size predictions deviate significantly from experimental observations at low salt concentrations. We attribute this discrepancy to the neglect of ion correlations in the implicit-salt model. At higher salt concentrations, we find reasonable agreement of the Yukawa model with experimental data. The crossover from low to high salt concentrations is reached when the electrostatic screening length becomes comparable to the headgroup size. © 2009 American Chemical Society.

  1. Comparison of the performance of non-ionic and anionic surfactants as mobile phase additives in the RPLC analysis of basic drugs.

    Science.gov (United States)

    Ruiz-Ángel, María J; García-Álvarez-Coque, María C

    2011-03-01

    Surfactants added to the mobile phases in reversed-phase liquid chromatography (RPLC) give rise to a modified stationary phase, due to the adsorption of surfactant monomers. Depending on the surfactant nature (ionic or non-ionic), the coated stationary phase can exhibit a positive net charge, or just change its polarity remaining neutral. Also, micelles in the mobile phase introduce new sites for solute interaction. This affects the chromatographic behavior, especially in the case of basic compounds. Two surfactants of different nature, the non-ionic Brij-35 and the anionic sodium dodecyl sulfate (SDS) added to water or aqueous-organic mixtures, are here compared in the separation of basic compounds (β-blockers and tricyclic antidepressants). The reversible/irreversible adsorption of the monomers of both surfactants on the stationary phase was examined. The changes in the nature of the chromatographic system using different columns and chromatographic conditions were followed based on the changes in retention and peak shape. The study revealed that Brij-35 is suitable for analyzing basic compounds of intermediate polarity, using "green chemistry", since the addition of an organic solvent is not needed and Brij-35 is a biodegradable surfactant. In contrast, RPLC with hydro-organic mixtures or mobile phases containing SDS required high concentrations of organic solvents. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  2. Differential modulation of the chaperone-like activity of HSP-1/2, a major protein of horse seminal plasma by anionic and cationic surfactants.

    Science.gov (United States)

    Kumar, C Sudheer; Swamy, Musti J

    2017-03-01

    The major protein of equine seminal plasma, HSP-1/2 exhibits chaperone-like activity (CLA) by protecting various target proteins against thermal, chemical and oxidative stress. Polydispersity and surface hydrophobicity of HSP-1/2 were found to be important for its CLA. Surfactants are known to alter certain properties of proteins, e.g. hydrophobicity, charge and conformation either by altering properties of the medium or by direct binding. In the current study, thermal aggregation of alcohol dehydrogenase (ADH) and enolase has been studied in the presence of HSP-1/2, different surfactants and their combinations. The results obtained show that anionic surfactants (SDS, sodium dodecyl benzene sulfate) and neutral surfactants (tween-20, triton X-100) increase the CLA of HSP-1/2 and also inhibit aggregation of the target proteins independently. On the other hand, cationic surfactants (CTAB, alanine palmityl ester) increased the thermal aggregation of ADH and enolase and also decreased the CLA of HSP-1/2. These results are of significant interest as they show that surfactants such as SDS and tween-20 can potentially be used as anti-aggregation agents to prevent thermal aggregation of target proteins. Copyright © 2016 Elsevier B.V. All rights reserved.

  3. Investigation on stabilization of CO2 foam by ionic and nonionic surfactants in presence of different additives for application in enhanced oil recovery

    Science.gov (United States)

    Kumar, Sunil; Mandal, Ajay

    2017-10-01

    Application of foam in upstream petroleum industry specifically in enhanced oil recovery (EOR) has gained significant interest in recent years. In view of this, an attempt has been paid to design the suitable foaming agents (foamer) by evaluating the influence of three surfactants, five nanoparticles and several additives. Experimental investigations have been carried out in order to examine the mechanism of foam generation in presence of sodium dodecyl sulfate (SDS), cetyltrimethylammonium bromide (CTAB) and polysorbate 80 (Tween 80) as anionic, cationic and nonionic surfactants by using the CO2 as gaseous component. It has been found that ionic surfactants show the higher foam life compared to nonionic surfactant. Out of different nano particles used, namely alumina (Al2O3) zirconium oxide (ZrO2), calcium carbonate (CaCO3), boron nitride (BN) and silica (SiO2), boron nitride shows the maximum improvement of foam stability. The foam stability of surfactant-nanoparticles foam is further increased by addition of different additives viz. polymer, alcohol and alkali. The results show that, the designed foaming solution have nearly 2.5 times higher half-decay time (t1/2) compared to the simple surfactant system. Finally, it has been found that gas injection rate plays an important role in obtaining a uniform and stabilized foam.

  4. Effect of surfactants on the aggregation of pyronin B and pyronin Y in aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Arik, Mustafa; Meral, Kadem [Department of Chemistry, Faculty of Sciences, Atatuerk University, 25240 Erzurum (Turkey); Onganer, Yavuz, E-mail: yonganer@atauni.edu.t [Department of Chemistry, Faculty of Sciences, Atatuerk University, 25240 Erzurum (Turkey)

    2009-06-15

    Molecular dynamics of pyronin B (PyB) and pyronin Y (PyY) in aqueous solution containing different surfactants were investigated by using absorption and fluorescence spectroscopy techniques. First, the interactions of PyB and PyY with the negatively charged surfactant sodium dodecyl sulphate (SDS) were investigated in the below and above critical micelle concentration (cmc). The H-aggregate formation of the dye compounds was observed for below the cmc of SDS surfactant. The absorbance of H-aggregate absorption band of PyB and PyY decreased according to the aggregate-monomer equilibrium by increasing SDS surfactant concentration towards the cmc. Therefore, equilibrium constants of the aggregate formation and oscillator strengths of monomer and aggregate of the dye compounds were calculated from spectral studies. Moreover, aggregate formation dynamics was discussed in terms of thermodynamic functions by using temperature studies. The interactions of PyB and PyY with the positively charged hexadecyltrimethylammonium bromide (CTAB) and neutral Triton X-100 (TX-100) were also studied and it was observed that there was no aggregate formation on the absorption and fluorescence spectra for below and above the cmc.

  5. Optimizing the surfactant for the aqueous processing of LiFePO{sub 4} composite electrodes

    Energy Technology Data Exchange (ETDEWEB)

    Porcher, W.; Jouanneau, S. [Commissariat a l' Energie Atomique, 38054 Grenoble Cedex 9 (France); Lestriez, B.; Guyomard, D. [Institut des Materiaux Jean Rouxel (IMN), Universite de Nantes, CNRS, 44322 Nantes Cedex 3 (France)

    2010-05-01

    Aqueous processing would reduce the costs associated with the making of the composite electrode. To achieve the incorporation and the dispersion of the carbon black (CB) conductive agent in aqueous slurries, a surfactant is needed. In this paper, three surfactants are compared, an anionic one, the sodium dodecyle sulphate (SDS), a non-ionic one, the isooctylphenylether of polyoxyethylene called commercially Triton X-100 and a cationic one, the hexadecyltrimethylammonium bromide (CTAB), by using rheology and laser granulometry measurements on electrode slurries on one hand, and SEM observations, porosity and adhesion measurements and electrochemical testing on composite electrodes on the other hand. Ionic surfactants were found to be not suitable because a corrosion of the aluminium current collector occurred. The utilization of Triton X-100 favoured a more homogeneous CB distribution, resulted in a better electronic wiring of the active material particles and higher rate behavior of the electrode. Optimal electrochemical performances are obtained for an optimal surfactant concentration which depends on the BET surface area of the CB powder. (author)

  6. Denaturation of proteins by surfactants studied by the Taylor dispersion analysis.

    Directory of Open Access Journals (Sweden)

    Aldona Jelińska

    Full Text Available We showed that the Taylor Dispersion Analysis (TDA is a fast and easy to use method for the study of denaturation proteins. We applied TDA to study denaturation of β-lactoglobulin, transferrin, and human insulin by anionic surfactant sodium dodecyl sulfate (SDS. A series of measurements at constant protein concentration (for transferrin was 1.9 x 10-5 M, for β- lactoglobulin was 7.6 x 10-5 M, and for insulin was 1.2 x 10-4 M and varying SDS concentrations were carried out in the phosphate-buffered saline (PBS. The structural changes were analyzed based on the diffusion coefficients of the complexes formed at various surfactant concentrations. The concentration of surfactant was varied in the range from 1.2 x 10-4 M to 8.7 x 10-2 M. We determined the minimum concentration of the surfactant necessary to change the native conformation of the proteins. The minimal concentration of SDS for β-lactoglobulin and transferrin was 4.3 x 10-4 M and for insulin 2.3 x 10-4 M. To evaluate the TDA as a novel method for studying denaturation of proteins we also applied other methods i.e. electronic circular dichroism (ECD and dynamic light scattering (DLS to study the same phenomenon. The results obtained using these methods were in agreement with the results from TDA.

  7. Adsorption Of Surfactants At the Water-Oil Interface By Short-Time Diffusion

    Science.gov (United States)

    Cortes-Estrada, Aldo; Ibarra-Bracamontes, Laura; Aguilar-Corona, Alicia; Viramontes-Gamboa, Gonzalo

    2017-11-01

    Surface tension is an important parameter for different industrial processes. The addition of surfactants can modify the interfacial tension between two fluids. As the surfactant molecules reach and are adsorbed at a fluid interface, the surface tension or interfacial tension is reduced until the interface is saturated. Dynamic Interfacial tension measurements were carried out using an optical tensiometer by the Pendant Drop technique at a room temperature of 25 °C for a period of 250 sec. A drop of surfactant solution was deposited and allowed to diffuse into a water-oil interface, and then the adsorption rate at the interface was calculated. Sodium Dodecyl Sulfate (SDS) was used as the surfactant, hexane and dodecane were tested as the oil phase. A linear decay in the interfacial tension was observed for the lower initial concentrations of the order of 0.0001 to 0.01 mM, and an exponential decay was observed for initial concentrations of the order of 0.1 to 1 mM. This study was supported by the Mexican Council of Science and Technology (CONACyT) and by the Scientific Research Coordination of the University of Michoacan in Mexico.

  8. Size-dependent interaction of silica nanoparticles with different surfactants in aqueous solution.

    Science.gov (United States)

    Kumar, Sugam; Aswal, Vinod K; Kohlbrecher, Joachim

    2012-06-26

    The size-dependent interaction of anionic silica nanoparticles with ionic (anionic and cationic) and nonionic surfactants has been studied using small-angle neutron scattering (SANS). The surfactants used are anionic sodium dodecyl sulfate (SDS), cationic dodecyltrimethyl ammonium bromide (DTAB), and nonionic decaoxyethylene n-dodecylether (C(12)E(10)). The measurements have been carried out for three different sizes of silica nanoparticles (8, 16, and 26 nm) at fixed concentrations (1 wt % each) of nanoparticles and surfactants. It is found that irrespective of the size of the nanoparticles there is no significant interaction evolved between like-charged nanoparticles and the SDS micelles leading to any structural changes. However, the strong attraction of oppositely charged DTAB micelles with silica nanoparticles results in the aggregation of nanoparticles. The number of micelles mediating the nanoparticle aggregation increases with the size of the nanoparticle. The aggregates are characterized by fractal structure where the fractal dimension is found to be constant (D ≈ 2.3) independent of the size of the nanoparticles and consistent with diffusion-limited-aggregation-type fractal morphology in these systems. In the case of nonionic surfactant C(12)E(10), micelles interact with the individual silica nanoparticles. The number of adsorbed micelles per nanoparticle increases drastically whereas the percentage of adsorbed micelles on nanoparticles decreases with the increase in the size of the nanoparticles.

  9. A Spectroscopic and Electrochemical Investigation of Interactions of Anticancer Uracil Derivatives with Cationic and Anionic Surfactants

    International Nuclear Information System (INIS)

    Zafar, F.; Shah, A.; Ahmad, Z.; Siddiq, M.; Ali, S.; Asad Muhammad Khan, A. M.; Rana, U. A.

    2015-01-01

    Interactions of 5-fluorouracil (5-FU), a commercially available anti-cancer drug and two other possibly anti-cancer actives, 2-thiouracil (2-TU) and 2,4-dithiouracil (DTU), with anionic sodium dodecyl sulphate (SDS) and cationic cetlytrimethyl ammonium bromide (CTAB) surfactants were studied using cyclic voltammetry and UV-Visible spectroscopic techniques. The results from both techniques asserted the formation of complex between the drugs and surfactants. In the pre-micellar concentrations, the binding was mainly due to the interactions between the surfactants monomers (electrostatic) and the drug molecules, while in the post-micellar region, drug was encapsulated within the micelle due to electrostatic as well as hydrophobic interactions. The UV-Visible spectroscopic data of the interaction between 5-fluorouracil and the surfactants exhibited an isobestic point which indicated the presence of equilibrium species in bulk and the micellar phase. Binding constant, partition coefficient between bulk and miceller phase, and the number of drug molecules incorporated per micelle were calculated. (author)

  10. The effect of surfactant on fermentation of kitasamycin in Streptomyces kitasatoensis.

    Science.gov (United States)

    Zheng, Qianli; Gao, Shuhong

    2016-11-01

    Soybean oil is an important carbon source in kitasamycin fermentation by Streptomyces kitasatoensis. In this study, three different surfactants, Tween 80, Tween 85, and sodium dodecyl sulfate (SDS), were added in the fermentation medium to improve soybean oil utilization. Results indicated that all of these surfactants promote kitasamycin biosynthesis. When 0.5 g/L SDS was added at the beginning of fermentation, kitasamycin production increased by 55% and A 5 content improved by 12%, compared with the control treatment (i.e., no surfactant added). Oil consumption rate and lipase activity were also improved in the presence of SDS, producing more organic acids benefiting kitasamycin biosynthesis. High butyric acid concentration in the fermentation medium containing SDS repressed C-3 acetylation and promoted A 5 component accumulation. Additionally, utilization of oil components by S. kitasatoensis was altered. Specifically, linoleic acid was primarily used in the fermentation process with SDS, whereas oleic acid was primarily used in the fermentation process where no surfactant had been added. © 2015 International Union of Biochemistry and Molecular Biology, Inc.

  11. Surfactant-induced skin irritation and skin repair. Evaluation of the acute human irritation model by noninvasive techniques.

    Science.gov (United States)

    Wilhelm, K P; Freitag, G; Wolff, H H

    1994-06-01

    Although the induction of irritant dermatitis by surfactants has been extensively studied in recent years, our understanding of the repair phase of irritant dermatitis is limited. We investigated qualitative and quantitative differences in surfactant-induced irritant skin reactions from short-term exposure to three structurally different surfactants. Sodium lauryl sulfate (SLS), dodecyl trimethyl ammonium bromide (DTAB), and potassium soap were the model irritants. Surfactant solutions (0.5%) were applied for 24 hours to the volar aspect of the forearm of 11 volunteers. Irritant reactions were assessed until complete healing was indicated by visual assessment and by various aspects of skin function, that is, transepidermal water loss (TEWL), erythema (skin color reflectance), and stratum that is, transepidermal water loss (TEWL), erythema (skin color reflectance), and stratum corneum hydration (electrical capacitance). SLS and DTAB induced similar degrees of erythema, whereas SLS induced significantly higher TEWL increase. Although both erythema and TEWL were highest 1 hour after exposure to surfactants, skin dryness was a symptom with delayed onset, justifying the long observation period in this study. Minimum hydration values were measured as late as 7 days after surfactant exposure. Dryness was significantly more pronounced in areas exposed to SLS than in areas exposed to DTAB. Complete repair of the irritant reaction induced by either SLS or DTAB was achieved 17 days after surfactant exposure. Stratum corneum hydration was the last feature to return to baseline values. Potassium soap did not significantly influence any skin function. We emphasize the importance of extended periods needed before a patient with irritant contact dermatitis can be reexposed to irritant substances. The evaluation of the irritation potential of diverse surfactants depended significantly on the feature (erythema vs hydration and TEWL) measured.

  12. Magnetic surfactants

    OpenAIRE

    Brown, P.; Alan Hatton, T.; Eastoe, J.

    2015-01-01

    Surfactants are ubiquitous, being important commodity chemicals with wide industrial applications, and essential components of living organisms. With stimuli-responsive surfactants, self-assembly and physicochemical properties of a wide variety of materials may be readily manipulated, both reversibly and irreversibly. Until recently, magnetically responsive surfactants had not been reported. This review reports the recent progress in magnetoresponsive surfactants, covering control of interfac...

  13. Synthesis and characterization of anionic/nonionic surfactant-interceded iron-doped TiO{sub 2} to enhance sorbent/photo-catalytic properties

    Energy Technology Data Exchange (ETDEWEB)

    Sharma, Ajit; Lee, Byeong-Kyu, E-mail: bklee@ulsan.ac.kr

    2015-09-15

    We investigated the synthesis, characterization, and application of surfactant-interceded Fe nanoparticle-doped TiO{sub 2} (TiO{sub 2}/Fe-S1 and TiO{sub 2}/Fe-S2) that were used as adsorbents and photo-catalysts for the removal of As(V) ions from aqueous media. Two types of surfactant (anionic (sodium dodecyl sulfate), S1 and non-ionic (Triton X-100), S2) were used to obtain the separation and mono-dispersion of Fe(III) ions in the reaction solution. The nanocomposites were characterized by Fourier transform infrared (FTIR) spectroscopy, X-ray photoelectron spectroscopy (XPS), UV–vis, scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM/EDX) and elemental mapping analysis before and after As(V) removal. The Langmuir capacities (q{sub e}, mg/g) of the sodium dodecyl sulfate (SDS) and Triton X-100 interceded nanocomposites (TiO{sub 2}/Fe-S1 and TiO{sub 2}/Fe-S2, respectively) for arsenic removal were determined to be 65.79 and 50.76 mg/g, respectively, in aqueous media with As(V) concentration ranges of 0–10 mg/L at pH 6.5. - Highlights: • Fe(III) doped TiO{sub 2} nanocomposite was prepared with surfactant. • Anionic surfactant SDS enhanced the transfer of Fe(III) ions to TiO{sub 2}. • Surfactant-interceded nanocomposite enhanced As(V) removal. • Arsenic removal efficiency was as follows: dark phase>visible phase>UV region.

  14. Proteinograma sérico de veados-catingueiro (Mazama gouazoubira criados em cativeiro obtido por eletroforese em gel de agarose e de poliacrilamida (SDS PAGE Serum protein concentrations of captive brown brocket deer (Mazama gouazoubira determined by means of agarosis and sodium dodecyl sulphate-polyacrylamide (SDS-PAGE gel electrophoresis

    Directory of Open Access Journals (Sweden)

    A.M. Santana

    2008-12-01

    Full Text Available The serum protein concentrations of brown brocket deer (Mazama gouazoubira obtained by agarosis gel and sodium dodecyl sulphate-polyacrylamide (SDS-PAGE gel were determined from blood samples of ten adult healthy animals (six females and four males, monthly collected in the morning, during 12 months. The animals, maintained in individual stable and protected from noise, received ad libitum a diet of comercial ration and green roughage. Serum protein concentrations in agarosis gel revealed the presence of four protein fractions: albumin, alphaglobulin, betaglobulin, and gammaglobulin. Only serum concentrations of albumin were influenced by season, being values in spring higher than values in summer (4.15 x 3.64g/dl. Serum concentrations of albumin (4.05 x 3.75g/dl were higher for female and alphaglobulin (0.39 x 0.53g/dl werehigher for males. Results showed 34 proteins with molecular weights ranging from 18kD to 165kD. Significant differences between at least two seasons were found on values of 11 proteins. In conclusion, on account of the 10 animals been maintained in the same physical space and submitted to the same handling system, physiological variations, which are characteristic of this species, can be apointed as the reason of these differences.

  15. REMOVAL OF ANIONIC SURFACTANTS FROM WASTEWATER BY MAGNETIC MINERAL SORBENTS

    Directory of Open Access Journals (Sweden)

    Oksana Vladimirova Makarchuk

    2016-07-01

    Full Text Available The simplest and most effective method of removing low concentrations of anionic surfactants such as sodium dodecyl benzenesulfonate (SDBS and sodium lauryl sulfate (SLS is adsorption. Among adsorbents the natural clays are cheap and promising for these purposes. However, there are significant difficulties in removal of spent sorbent after the adsorption process. So, the creation of magnetic sorbents that can be effectively removed from water after sorption by magnetic separation will be a successful decision. The aim of this investigation is the creation of cheap and efficient magnetic sorbents based on natural clays and magnetite for anionic surfactant removal from wastewater. We have synthesized a series of magnetic sorbents from different natural clays with a content of magnetite from 2 to 10 wt%. The ability of magnetic sorbents to remove SDBS and SLS from aqueous solutions has been studied for different adsorbate concentrations by varying the amount of adsorbent, temperature and shaking time. Thermodynamic parameters were calculated from the slope and intercept of the linear plots of ln K against 1/T. Analysis of adsorption results obtained at different temperatures showed that the adsorption pattern on magnetic sorbents correspond to the Langmuir isotherm. It is shown that with increasing the content of magnetite in the magnetic sorbents improves not only their separation from water by magnetic separation, but adsorption capacity to SDBS and SLS. Thus, we obtained of cheap magnetic sorbents based on natural clays and magnetite by the easy way, which not only quickly separated from the solution by magnetic separation, but effectively remove anionic surfactants.

  16. Refolding of SDS-Unfolded Proteins by Nonionic Surfactants.

    Science.gov (United States)

    Kaspersen, Jørn Døvling; Søndergaard, Anne; Madsen, Daniel Jhaf; Otzen, Daniel E; Pedersen, Jan Skov

    2017-04-25

    The strong and usually denaturing interaction between anionic surfactants (AS) and proteins/enzymes has both benefits and drawbacks: for example, it is put to good use in electrophoretic mass determinations but limits enzyme efficiency in detergent formulations. Therefore, studies of the interactions between proteins and AS as well as nonionic surfactants (NIS) are of both basic and applied relevance. The AS sodium dodecyl sulfate (SDS) denatures and unfolds globular proteins under most conditions. In contrast, NIS such as octaethylene glycol monododecyl ether (C 12 E 8 ) and dodecyl maltoside (DDM) protect bovine serum albumin (BSA) from unfolding in SDS. Membrane proteins denatured in SDS can also be refolded by addition of NIS. Here, we investigate whether globular proteins unfolded by SDS can be refolded upon addition of C 12 E 8 and DDM. Four proteins, BSA, α-lactalbumin (αLA), lysozyme, and β-lactoglobulin (βLG), were studied by small-angle x-ray scattering and both near- and far-UV circular dichroism. All proteins and their complexes with SDS were attempted to be refolded by the addition of C 12 E 8 , while DDM was additionally added to SDS-denatured αLA and βLG. Except for αLA, the proteins did not interact with NIS alone. For all proteins, the addition of NIS to the protein-SDS samples resulted in extraction of the SDS from the protein-SDS complexes and refolding of βLG, BSA, and lysozyme, while αLA changed to its NIS-bound state instead of the native state. We conclude that NIS competes with globular proteins for association with SDS, making it possible to release and refold SDS-denatured proteins by adding sufficient amounts of NIS, unless the protein also interacts with NIS alone. Copyright © 2017 Biophysical Society. Published by Elsevier Inc. All rights reserved.

  17. A sensitive fluorescent probe for the polar solvation dynamics at protein-surfactant interfaces.

    Science.gov (United States)

    Singh, Priya; Choudhury, Susobhan; Singha, Subhankar; Jun, Yongwoong; Chakraborty, Sandipan; Sengupta, Jhimli; Das, Ranjan; Ahn, Kyo-Han; Pal, Samir Kumar

    2017-05-17

    Relaxation dynamics at the surface of biologically important macromolecules is important taking into account their functionality in molecular recognition. Over the years it has been shown that the solvation dynamics of a fluorescent probe at biomolecular surfaces and interfaces account for the relaxation dynamics of polar residues and associated water molecules. However, the sensitivity of the dynamics depends largely on the localization and exposure of the probe. For noncovalent fluorescent probes, localization at the region of interest in addition to surface exposure is an added challenge compared to the covalently attached probes at the biological interfaces. Here we have used a synthesized donor-acceptor type dipolar fluorophore, 6-acetyl-(2-((4-hydroxycyclohexyl)(methyl)amino)naphthalene) (ACYMAN), for the investigation of the solvation dynamics of a model protein-surfactant interface. A significant structural rearrangement of a model histone protein (H1) upon interaction with anionic surfactant sodium dodecyl sulphate (SDS) as revealed from the circular dichroism (CD) studies is nicely corroborated in the solvation dynamics of the probe at the interface. The polarization gated fluorescence anisotropy of the probe compared to that at the SDS micellar surface clearly reveals the localization of the probe at the protein-surfactant interface. We have also compared the sensitivity of ACYMAN with other solvation probes including coumarin 500 (C500) and 4-(dicyanomethylene)-2-methyl-6-(p-dimethylamino-styryl)-4H-pyran (DCM). In comparison to ACYMAN, both C500 and DCM fail to probe the interfacial solvation dynamics of a model protein-surfactant interface. While C500 is found to be delocalized from the protein-surfactant interface, DCM becomes destabilized upon the formation of the interface (protein-surfactant complex). The timescales obtained from this novel probe have also been compared with other femtosecond resolved studies and molecular dynamics simulations.

  18. Poly[bis(μ3-dodecyl sulfatocalcium

    Directory of Open Access Journals (Sweden)

    Genta Sakane

    2010-07-01

    Full Text Available In the title compound [Ca(C12H25O4S2]n, the unique CaII ion lies on an inversion center and is coordinated in a slightly distorted octahedral environment by six O atoms from dodecyl sulfate anions. The crystal structure is based on hydrocarbon (dodecyl sulfate layers which sandwich the CaII ions. Within the layers, the hydrocarbon zigzag chains are parallel to one another and interact via van der Waals forces.

  19. Coarsening of firefighting foams containing fluorinated hydrocarbon surfactants

    Science.gov (United States)

    Kennedy, Matthew J.; Dougherty, John A.; Otto, Nicholas; Conroy, Michael W.; Williams, Bradley A.; Ananth, Ramagopal; Fleming, James W.

    2013-03-01

    Diffusion of gas between bubbles in foam causes growth of large bubbles at the expense of small bubbles and leads to increasing mean bubble size with time thereby affecting drainage. Experimental data shows that the effective diffusivity of nitrogen gas in aqueous film forming foam (AFFF), which is widely used in firefighting against burning liquids, is several times smaller than in 1% sodium dodecyl sulfate (SDS) foam based on time-series photographs of bubble size and weighing scale recordings of liquid drainage. Differences in foam structure arising from foam production might contribute to the apparent difference in the rates of coarsening. AFFF solution produces wetter foam with initially smaller bubbles than SDS solution due in part to the lower gas-liquid surface tension provided by the fluorosurfactants present in AFFF. Present method of foam production generates microbubble foam by high-speed co-injection of surfactant solution and gas into a tube of 3-mm diameter. These results contribute to our growing understanding of the coupling between foam liquid fraction, bubble size, surfactant chemistry, and coarsening. NRC Resident Research Associate at NRL

  20. Thermodynamic Study of the Ion-Pair Complexation Equilibria of Dye and Surfactant by Spectral Titration and Chemometric Analysis

    Directory of Open Access Journals (Sweden)

    Hakimeh Abbasi Awal

    2017-12-01

    Full Text Available Surfactant-dye interactions are very important in chemical and dyeing processes. The dyes interact strongly with surfactant and show new spectrophotometric properties, so the UV-vis absorption spectrophotometric method has been used to study this process and extract some thermodynamic parameters. In this work, the association equilibrium between ionic dyes and ionic surfactant were studied by analyzing spectrophotometric data using chemometric methods. Methyl orange and crystal violet were selected as a model of cationic and anionic dyes respectively. Also sodium dodecyl sulphate and cetyltrimethylammonium bromide were selected as anionic and cationic surfactant, respectively. Hard model methods such as target transform fitting (TTF classical multi-wavelength fitting and soft model method such as multivariate curve resolution (MCR were used to analyze data that were recorded as a function of surfactant concentration in premicellar and postmicellar regions. Hard model methods were used to resolve data using ion-pair model in premicellar region in order to extract the concentration and spectral profiles of individual components and also related thermodynamic parameters. The equilibrium constants and other thermodynamic parameters of interaction of dyes with surfactants were determined by studying the dependence of their absorption spectra on the temperature in the range 293–308 K at concentrations of 5 × 10−6 M and 8 × 10−6 M for dye crystal violet and methyl orange, respectively. In postmicellar region, the MCR-ALS method was applied for resolving data and getting the spectra and concentration profiles in complex mixtures of dyes and surfactants.

  1. Investigation of formation constant of complex of a new synthesized tripodal ligand with Cu2+ using rank annihilation factor analysis in surfactant media

    Directory of Open Access Journals (Sweden)

    R. Golbedaghi

    2014-01-01

    Full Text Available The complex formation between a newly synthesized tripodal ligand and the cation Cu2+ in water and surfactant media was studied spectrophotometrically using rank annihilation factor analysis (RAFA. According to molar ratio data the stoichiometry of complexation between the ligand and the cation Cu2+ was 1:1. Formation constant of this complex was derived using RAFA on spectrophotometric data. The performance of the method has been evaluated by using synthetic data. Also concentration and spectral profiles of ligand and complex can be obtained by using the stability constant and appropriate equations. The effect of surfactants such as sodium dodecyl sulfate (SDS, cetyltrimethylammonium bromide (CTAB and Triton X-100 on complex formation constant of Cu2+ with the ligand was investigated.

  2. Different Surfactants-Assisted Hydrothermal Fabrication and Photocatalytic Properties of Bi2MoO6 for Methylene Blue Degradation under Simulated Sunlight Irradiation

    Directory of Open Access Journals (Sweden)

    Wenfeng Guo

    2014-01-01

    Full Text Available Bi2MoO6 single-crystallites were synthesized by a simple hydrothermal method in the presence of surfactant sodium dodecyl sulfate (SDS, polyvinyl pyrrolidone (PVP, or cetyl trimethyl ammonium bromide (CTAB. The samples were characterized by X-ray diffraction (XRD, transmission electron microscopy (TEM, and ultraviolet-visible diffuse reflectance spectra (UV-vis DRS techniques. The photocatalytic activities of the as-fabricated Bi2MoO6 samples were measured for the degradation of methylene blue (MB under the Xe light illumination. It is shown that the introduction of surfactant have a crucial influence on the size and morphology of the Bi2MoO6 product. Among the as-fabricated Bi2MoO6 samples, the ones derived hydrothermally with CTAB showed outstanding photocatalytic activities for the addressed reaction under simulated sunlight irradiation, attributed to the ultrafine nanocrystals and the higher surface areas.

  3. Molecular dynamics study of the effect of calcium ions on the monolayer of SDC and SDSn surfactants at the vapor/liquid interface.

    Science.gov (United States)

    Yan, Hui; Guo, Xin-Li; Yuan, Shi-Ling; Liu, Cheng-Bu

    2011-05-17

    The effect of Ca(2+) ions on the hydration shell of sodium dodecyl carboxylate (SDC) and sodium dodecyl sulfonate (SDSn) monolayer at vapor/liquid interfaces was studied using molecular dynamics simulations. For each surfactant, two different surface concentrations were used to perform the simulations, and the aggregation morphologies and structural details have been reported. The results showed that the aggregation structures relate to both the surface coverage and the calcium ions. The divalent ions can screen the interaction between the polar head and Na(+) ions. Thus, Ca(2+) ions locate near the vapor/liquid interface to bind to the headgroup, making the aggregations much more compact via the salt bridge. The potential of mean force (PMF) between Ca(2+) and the headgroups shows that the interaction is decided by a stabilizing solvent-separated minimum in the PMF. To bind to the headgroup, Ca(2+) should overcome the energy barrier. Among contributions to the PMF, the major repulsive interaction was due to the rearrangement of the hydration shell after the calcium ions entered into the hydration shell of the headgroup. The PMFs between the headgroup and Ca(2+) in the SDSn systems showed higher energy barriers than those in the SDC systems. This result indicated that SDSn binds the divalent ions with more difficulty compared with SDC, so the ions have a strong effect on the hydration shell of SDC. That is why sulfonate surfactants have better efficiency in salt solutions with Ca(2+) ions for enhanced oil recovery.

  4. Effects of length and hydrophilicity/hydrophobicity of diamines on self-assembly of diamine/SDS gemini-like surfactants.

    Science.gov (United States)

    Chen, Zhidi; Penfold, Jeffrey; Li, Peixun; Doutch, James; Fan, Yaxun; Wang, Yilin

    2017-12-06

    This work studied gemini-like surfactants formed from anionic surfactant sodium dodecyl sulfate (SDS) and cationic charged bola-type diamines with hydrophilic or hydrophobic spacers of different lengths using surface tension, small angle neutron scattering, isothermal titration microcalorimetry and cryogenic transmission electron microscopy. The critical micelle concentrations (CMC) and the surface tension at CMC (γ CMC ) for all the diamine/SDS mixtures are markedly lower than that of SDS. The shorter diamines reduce γ CMC to a greater extent regardless of the hydrophilicity/hydrophobicity of the diamines. Meanwhile, either the hydrophobic diamine with a longer spacer or the hydrophilic diamine with a shorter spacer is more beneficial to decrease CMC and leads to the transition from spherical micelles into rodlike or wormlike micelles. This is principally because of the formation of gemini-like surfactants by the electrostatic binding between SDS and the diamines, where the electrostatic repulsion between the adjacent headgroups of SDS becomes much weaker due to the electrostatic binding of oppositely charged diamine with SDS, and the longer hydrophobic spacer may also bend into the hydrophobic domain of micelles to promote micellar growth. However, the hydrophilic spacers are more compatible with the headgroup region, leading to micelles with a larger curvature. This work contributes to the understanding of the relationship between the properties of constructed gemini-like surfactants and the natures of connecting molecules, and provides guidance to efficiently improve the performance of surfactants.

  5. Synthesis of dodecyl lauroyl benzene sulfonate and its application in enhanced oil recovery

    Energy Technology Data Exchange (ETDEWEB)

    Cui, Zhenggang; Wu, Le; Sun, Mingming; Jiang, Jian-zhong; Wang, Feng [Jiangnan Univ., Wuxi (China). School of Chemical and Material Engineering

    2011-09-15

    A new hydrophobic surfactant, dodecyl lauroyl benzene sulfonate (DLBS), was synthesized and its application in enhanced oil recovery by alkali-surfactant-polymer (ASP) flooding was studied. The results show that DLBS can be synthesized by reaction of industrial dodecyl benzene with lauroyl chloride in the presence of AlCl{sub 3}, followed by sulfonation with ClSO{sub 3}H and neutralization with NaOH. The lauroyl-group is confirmed to be connected to the para-position of the alkylbenzene by1HNMR spectrum. The synthesized DLBS is well soluble in pure water and reservoir (connate) water at 45 C. It is highly surface active which is indicated by its low CMC of 1.1 . 10{sup -5} mol/L, and its low surface tension, {gamma}{sub cmc} of 28.6 mN m{sup -1}. By mixing with heavy alkylbenzene sulfonates of relatively low average molar mass (387g mol{sup -1}) at a total surfactant concentration of 5 mM, DLBS can reduce the interfacial tension of Daqing crude oil/connate water to an order of 10{sup -3} mN/m at 45 C in the presence of 0.5-1.0 wt.% NaOH and 1000 mg L{sup -1} of polymer. If the NaOH was replaced by a gentle alkaline salt, Na{sub 2}CO{sub 3}, certain amounts of dodecyl dimethyl carboxy betaine were added and the concentration of Na{sub 2}CO{sub 3} was increased to 1.2-2.0 wt.%, the interfacial tension of Daqing crude oil/connate water can also be reduced to an ultralow value. Therefore DLBS is a good hydrophobic surfactant applicable in ASP flooding with either NaOH or Na{sub 2}CO{sub 3} as alkaline agents. (orig.)

  6. Influence of synthetic surfactants on the uptake of Pd, Cd and Pb by the marine macroalga, Ulva lactuca

    Energy Technology Data Exchange (ETDEWEB)

    Masakorala, Kanaji [School of Earth, Ocean and Environmental Sciences, University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom); Turner, Andrew [School of Earth, Ocean and Environmental Sciences, University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom)], E-mail: aturner@plymouth.ac.uk; Brown, Murray T. [School of Biological Sciences, University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom)

    2008-12-15

    Uptake of Pd, Cd and Pb by the marine macroalga, Ulva lactuca, has been studied in the presence of an anionic (sodium dodecyl sulphate, SDS), cationic (hexadecyltrimethylammonium bromide; HDTMA) and non-ionic (Triton X-100; TX) surfactant. Compared with the surfactant-free system, metal sorption was reduced in the presence of SDS or TX. Neither surfactant, however, had any measurable impact on cell membrane permeability, determined by leakage of dissolved free amino acids (DFAA), or on metal internalisation. We attribute these observations to the stabilisation of aqueous Cd and Pb by SDS and the shielding of otherwise amenable sorption sites by TX. Presence of HDTMA resulted in a reduction in the extent of both sorption and internalisation of all metals and a significant increase in the leakage of DFAA. Thus, by enhancing membrane permeability, HDTMA exerts the greatest influence on metal behaviour in the presence of U. lactuca. - Synthetic surfactants exert a significant impact on the uptake and internalisation of metals by a marine macroalga.

  7. Signal amplification in electrochemical detection of buckwheat allergenic protein using field effect transistor biosensor by introduction of anionic surfactant

    Directory of Open Access Journals (Sweden)

    Sho Hideshima

    2016-03-01

    Full Text Available Food allergens, especially buckwheat proteins, sometimes induce anaphylactic shock in patients after ingestion. Development of a simple and rapid screening method based on a field effect transistor (FET biosensor for food allergens in food facilities or products is in demand. In this study, we achieved the FET detection of a buckwheat allergenic protein (BWp16, which is not charged enough to be electrically detected by FET biosensors, by introducing additional negative charges from anionic surfactants to the target proteins. A change in the FET characteristics reflecting surface potential caused by the adsorption of target charged proteins was observed when the target sample was coupled with the anionic surfactant (sodium dodecyl sulfate; SDS, while no significant response was detected without any surfactant treatment. It was suggested that the surfactant conjugated with the protein could be useful for the charge amplification of the target proteins. The surface plasmon resonance analysis revealed that the SDS-coupled proteins were successfully captured by the receptors immobilized on the sensing surface. Additionally, we obtained the FET responses at various concentrations of BWp16 ranging from 1 ng/mL to 10 μg/mL. These results suggest that a signal amplification method for FET biosensing is useful for allergen detection in the food industry.

  8. Synergistic Effect of Hydrotrope and Surfactant on Solubility and Dissolution of Atorvastatin Calcium: Screening Factorial Design Followed by Ratio Optimization

    Science.gov (United States)

    Patel, V. F.; Sarai, J.

    2014-01-01

    The present study was aimed at investigating the effect of hydrotrope and surfactant on poor solubility of atorvastatin calcium. Excipients screening followed by factorial design was performed to study effect of excipients and manufacturing methods on solubility of drug. Three independent factors (carrier, surfactant and manufacturing method) were evaluated at two levels using solubility as a dependant variable. Solid-state characterisation was performed using Fourier transform infrared spectroscopy and differential scanning calorimetry. Optimised complex were incorporated into orally disintegrating micro tablets and in vitro dissolution test was performed. Nicotinamide, Plasdone and sodium dodecyl sulphate were emerged as promising excipients from excipient screening. General regression analysis revealed only the type of carrier has significantly enhanced (Psolubility of drug while other factors were found to be nonsignificant. Ratio optimisation trial revealed that drug to nicotinamide ratio is more critical in enhancing the solubility of drug (40 fold increases in solubility compared to pure drug) in comparison to drug-surfactant ratio; however the presence of surfactant deemed essential. Significantly higher rate and extent of dissolution was observed from solid dispersion complex and tablets compared to dissolution of pure drug (Psolubility and dissolution of atorvastatin calcium and this can be explored further. PMID:25593381

  9. Influence of synthetic surfactants on the uptake of Pd, Cd and Pb by the marine macroalga, Ulva lactuca

    International Nuclear Information System (INIS)

    Masakorala, Kanaji; Turner, Andrew; Brown, Murray T.

    2008-01-01

    Uptake of Pd, Cd and Pb by the marine macroalga, Ulva lactuca, has been studied in the presence of an anionic (sodium dodecyl sulphate, SDS), cationic (hexadecyltrimethylammonium bromide; HDTMA) and non-ionic (Triton X-100; TX) surfactant. Compared with the surfactant-free system, metal sorption was reduced in the presence of SDS or TX. Neither surfactant, however, had any measurable impact on cell membrane permeability, determined by leakage of dissolved free amino acids (DFAA), or on metal internalisation. We attribute these observations to the stabilisation of aqueous Cd and Pb by SDS and the shielding of otherwise amenable sorption sites by TX. Presence of HDTMA resulted in a reduction in the extent of both sorption and internalisation of all metals and a significant increase in the leakage of DFAA. Thus, by enhancing membrane permeability, HDTMA exerts the greatest influence on metal behaviour in the presence of U. lactuca. - Synthetic surfactants exert a significant impact on the uptake and internalisation of metals by a marine macroalga

  10. The inhibition of methane hydrate formation by water alignment underneath surface adsorption of surfactants

    Energy Technology Data Exchange (ETDEWEB)

    Nguyen, Ngoc N.; Nguyen, Anh V.; Dang, Liem X.

    2017-06-01

    Sodium dodecyl sulfate (SDS) has been widely shown to strongly promote the formation of methane hydrate. Here we show that SDS displays an extraordinary inhibition effect on methane hydrate formation when the surfactant is used in sub-millimolar concentration (around 0.3 mM). We have also employed Sum Frequency Generation vibrational spectroscopy (SFG) and molecular dynamics simulation (MDS) to elucidate the molecular mechanism of this inhibition. The SFG and MDS results revealed a strong alignment of water molecules underneath surface adsorption of SDS in its sub-millimolar solution. Interestingly, both the alignment of water and the inhibition effect (in 0.3 mM SDS solution) went vanishing when an oppositely-charged surfactant (tetra-n-butylammonium bromide, TBAB) was suitably added to produce a mixed solution of 0.3 mM SDS and 3.6 mM TBAB. Combining structural and kinetic results, we pointed out that the alignment of water underneath surface adsorption of dodecyl sulfate (DS-) anions gave rise to the unexpected inhibition of methane hydration formation in sub-millimolar solution of SDS. The adoption of TBAB mitigated the SDS-induced electrostatic field at the solution’s surface and, therefore, weakened the alignment of interfacial water which, in turn, erased the inhibition effect. We discussed this finding using the concept of activation energy of the interfacial formation of gas hydrate. The main finding of this work is to reveal the interplay of interfacial water in governing gas hydrate formation which sheds light on a universal molecular-scale understanding of the influence of surfactants on gas hydrate formation. This work was supported by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences, and Biosciences. The calculations were carried out using computer resources provided by the Office of Basic Energy Sciences.

  11. Transport Properties of Water and Sodium Dodecyl Sulfate (Postprint)

    Science.gov (United States)

    2013-08-01

    applicability and on the molecular system to be studied [34,46]. Bulk liquid properties using rigid water models are extensively studied and available...intended to be used to simulate bulk liquid water. In order to investigate the transport properties of the MP2f water model, we computed the diffusion... Monde , M., 2012, “Enhancement of Nucleate Pool Boiling Heat Transfer in Ammonia/Water Mixtures With a Surface-Active Agent,” Int. J. Heat Mass Transfer

  12. Stabilization of solutions of feather keratins by sodium dodecyl sulphate

    NARCIS (Netherlands)

    Schrooyen, P.M.M.; Dijkstra, Pieter J.; Oberthür, Radulf C.; Bantjes, A.; Bantjes, Adriaan; Feijen, Jan

    2001-01-01

    Feather keratins were extracted from chicken feathers with aqueous solutions of urea and 2-mercaptoethanol. After filtration of the insoluble residue, a feather keratin solution was obtained. Removal of 2-mercaptoethanol and urea by dialysis resulted in aggregation of the keratin polypeptide chains

  13. Effect of sodium dodecyl sulfate on flow and electrokinetic properties ...

    Indian Academy of Sciences (India)

    Unknown

    gel appears to be broken by shear forces and the inter- particle bonds tend to reestablish themselves with time. (Lagaly 1989; Güven 1992). Thixotropy is an important characteristic for industrial applications. For example, drilling fluids and paints must be thixotropic. Bentonite suspensions are thixotropic and, for that reason, ...

  14. Effect of sodium dodecyl sulfate on flow and electrokinetic properties ...

    Indian Academy of Sciences (India)

    Unknown

    Bentonite with its higher ion exchange capa- city and surface ... gelation and in turn relatively high viscosity in bentonite. Bentonite ... at any shear of rate. A stable colloidal dispersion coagulates when a certain amount of salt is added. The minimum salt concentration that is needed to cause coagulation of a colloidal disper-.

  15. Sodium dodecyl sulfate-assisted synthesis of Ni nanoparticles ...

    Indian Academy of Sciences (India)

    31

    morphology, size, dispersion, magnetic properties and electrochemical activity of the nickel. 6 nanoparticles. ... 3. 1. Introduction. 1. Over the last decades, synthesis of magnetic metallic nanomaterials with different sizes and. 2 ... nanoparticles have became one of the attractive metallic nanomaterials which is expected to. 4.

  16. Enhanced perfume surface delivery to interfaces using surfactant surface multilayer structures.

    Science.gov (United States)

    Bradbury, Robert; Penfold, Jeffrey; Thomas, Robert K; Tucker, Ian M; Petkov, Jordan T; Jones, Craig

    2016-01-01

    Enhanced surface delivery and retention of perfumes at interfaces are the keys to their more effective and efficient deployment in a wide range of home and personal care related formulations. It has been previously demonstrated that the addition of multivalent counterions, notably Ca(2+), induces multilayer adsorption at the air-water interface for the anionic surfactant, sodium dodecyl-6-benzenesulfonate, LAS-6. Neutron reflectivity, NR, measurements are reported here which demonstrate that such surfactant surface multilayer structures are a potentially promising vehicle for enhanced delivery of perfumes to interfaces. The data show that the incorporation of the model perfumes, phenylethanol, PE, and linalool, LL, into the surface multilayer structure formed by LAS-6/Ca(2+) results in the surface structures being retained up to relatively high perfume mole fractions. Furthermore the amount of perfume at the surface is enhanced by at least an order of magnitude, compared to that co-adsorbed with a surfactant monolayer. Copyright © 2015 Elsevier Inc. All rights reserved.

  17. Surfactant-assisted growth of anodic nanoporous niobium oxide with a grained surface

    Energy Technology Data Exchange (ETDEWEB)

    Yoo, Jeong Eun [Department of Chemical Engineering, Inha University, 253 Yonghyun Dong, Nam-Gu, Incheon 402-751 (Korea, Republic of); Choi, Jinsub, E-mail: jinsub@inha.ac.k [Department of Chemical Engineering, Inha University, 253 Yonghyun Dong, Nam-Gu, Incheon 402-751 (Korea, Republic of)

    2010-07-15

    Nanoporous niobium oxide film with a maximum thickness of 520 nm was prepared by anodizing niobium in a mixture of 1 wt% HF, 1 M H{sub 3}PO{sub 4}, and a small amount of Sodium Dodecyl Sulfate (SDS) surfactant. The porosity of the anodic niobium oxide prepared without SDS is irregular with the surface of the oxide suggesting a grained surface pattern rather than an ordered porous structure. A proper amount of SDS addition can prepare a pore arrangement with stripe patterns. The pore depth and surface pattern were strongly affected by the concentration of SDS and bath temperature. We found that the addition of SDS surfactant facilitated improvement in the chemical resistance of niobium oxide, leading to the formation of pores with a longer length compared to those prepared without a SDS surfactant. This can be in part ascribed to the protection of the surface by the physical adsorption of SDS on the surface due to a charge-charge interaction and be in part attributed to the formation of Nb=O bonding on the outermost oxide layer by SDS. When anodization was carried out for 4 h, the surface dissolution of niobium oxide was observed, which means that the maximum tolerance time against chemical dissolution was less than 4 h.

  18. Effect of 60Co gamma-ray irradiation on dilute aqueous solutions of surfactants

    International Nuclear Information System (INIS)

    Sawai, Teruko; Shimokawa, Toshinari; Miki, Yasushi; Oseko, Koichi; Sawai, Takeshi

    1978-01-01

    Present work deals with the effects of gamma irradiation from 60 Co γ-ray source upon aqueous solutions of three kinds of surfactants. When dilute aqueous solutions of sodium dodecyl sulfate (SDS, anionic), cethyl trimethyl ammonium chloride (CTAC, cationic), and polyoxyethylene lauryl ether (POE, non-ionic) were irradiated with γ-rays at a room temperature, the residual concentration, products, surface tension, and forming power were examined by colorimetric method, IR spectrophotometric method, gaschromatography, Ross-Miles method, and Traube's stalagmometer etc. These surfactants were decomposed by the irradiation and thus the surface tension increased and the forming power, on the contrary, decreased with dose. Radiation chemical yields (G-value) of the degradation were about 1 for the solutions of SDS and CTAC, and about 0.3 for the POE solution. From the experimental results, it was found that following chemical reactions seem to occur followed by the radiolysis of water: a) bond cleavage of ester for SDS, of CN for CTAC, and of oxyethylene for POE, b) hydrogen abstraction from the surfactants, c) production of CO bond in the presence of dissolved oxygen. (auth.)

  19. [Effect of 60Co gamma-irradiation on dilute aqueous solutions of surfactants].

    Science.gov (United States)

    Sawai, T; Shimokowa, T; Miki, Y; Oseko, K; Sawai, T

    1978-01-01

    Present work deals with the effects of gamma irradiation from 60Co gamma-ray source upon aqueous solutions of three kinds of surfactants. When dilute aqueous solutions of sodium dodecyl sulfate (SDS, anionic), cethyl trimethyl ammonium chloride (CTAC, cationic), and polyoxyethylene lauryl ether (POE, non-ionic) were irradiated with gamma-rays at a room remperature, the residual concentration, products, surface tension, and forming power were examined by colorimetric method, IR spectrophotometric method, gaschromatography, Ross-Miles method, and Traube's stalagnometer etc.. These surfactants were decomposed by the irradiation and thus the surface tension increased and the forming power, on the contrary, decreased with dose. Radiation chemical yields (G-value) of the degradation were about 1 for the solutions of SDS and CTAC, and about 0.3 for the POE solution. From the experimental results, it was found that following chemical reactions seem to occur followed by the radiolysis of water; a) bond cleavage of ester for SDS, of CN for CTAC, and of oxyethylene for POE, b) hydrogen abstraction from the surfactants, c) production of CO bond in the presence of dissolved oxygen.

  20. Wetting Resistance of Commercial Membrane Distillation Membranes in Waste Streams Containing Surfactants and Oil

    Directory of Open Access Journals (Sweden)

    Lies Eykens

    2017-01-01

    Full Text Available Water management is becoming increasingly challenging and several technologies, including membrane distillation (MD are emerging. This technology is less affected by salinity compared to reverse osmosis and is able to treat brines up to saturation. The focus of MD research recently shifted from seawater desalination to industrial applications out of the scope of reverse osmosis. In many of these applications, surfactants or oil traces are present in the feed stream, lowering the surface tension and increasing the risk for membrane wetting. In this study, the technological boundaries of MD in the presence of surfactants are investigated using surface tension, contact angle and liquid entry pressure measurements together with lab-scale MD experiments to predict the wetting resistance of different membranes. Synthetic NaCl solutions mixed with sodium dodecyl sulfate (SDS were used as feed solution. The limiting surfactant concentration was found to be dependent on the surface chemistry of the membrane, and increased with increasing hydrophobicity and oleophobicity. Additionally, a hexadecane/SDS emulsion was prepared with a composition simulating produced water, a waste stream in the oil and gas sector. When hexadecane is present in the emulsion, oleophobic membranes are able to resist wetting, whereas polytetrafluoretheen (PTFE is gradually wetted by the feed liquid.

  1. Effect of Surfactants on Gas Holdup in Shear-Thinning Fluids

    Directory of Open Access Journals (Sweden)

    Shaobai Li

    2017-01-01

    Full Text Available In this study, the gas holdup of bubble swarms in shear-thinning fluids was experimentally studied at superficial gas velocities ranging from 0.001 to 0.02 m·s−1. Carboxylmethyl cellulose (CMC solutions of 0.2 wt%, 0.6 wt%, and 1.0 wt% with sodium dodecyl sulfate (SDS as the surfactant were used as the power-law (liquid phase, and nitrogen was used as the gas phase. Effects of SDS concentration, rheological behavior, and physical properties of the liquid phase and superficial gas velocity on gas holdup were investigated. Results indicated that gas holdup increases with increasing superficial gas velocity and decreasing CMC concentration. Moreover, the addition of SDS in CMC solutions increased gas holdup, and the degree increased with the surfactant concentration. An empirical correlation was proposed for evaluating gas holdup as a function of liquid surface tension, density, effective viscosity, rheological property, superficial gas velocity, and geometric characteristics of bubble columns using the experimental data obtained for the different superficial gas velocities and CMC solution concentrations with different surfactant solutions. These proposed correlations reasonably fitted the experimental data obtained for gas holdup in this system.

  2. Tensiometric, fluorescence and 1H NMR study of mixed micellization of non-steroidal anti-inflammatory drug sodium salt of ibuprofen in the presence of non-ionic surfactant in aqueous/urea solutions

    International Nuclear Information System (INIS)

    Rub, Malik Abdul; Khan, Farah; Sheikh, Mohmad Shafi; Azum, Naved; Asiri, Abdullah M.

    2016-01-01

    Highlights: • Interaction between (IBF + TX-100) mixtures has been investigated. • (IBF + TX-100) mixtures exhibit synergistic behavior. • Urea increases the surface charge of the micelles resulting halt of the micelles formation. • N agg , K sv and dielectric constant of mixed systems have also been evaluated. • 1 H NMR data suggested that IBF and TX-100 interacts through hydrophobic as well as hydrophillic interaction. - Abstract: The desirable surface/bulk properties for specific applications of drug sodium salt of ibuprofen (IBF) and Triton X-100 (TX-100) can be achieved by adjusting mainly the composition of these systems. The interactions of anionic drug IBF with non-ionic surfactant TX-100 micelles have been investigated using tensiometry, fluorometry and 1 H NMR in aqueous as well in 250 mmol⋅kg −1 urea solutions. Different theoretical models like Clint, Rubingh, and Rosen, etc. were utilized to get information about the nature of interaction between these two in bulk and at the interface. These models disclose that the non-ideal behavior with attractive interaction in bulk and at the interface exists. The steady-state fluorescence quenching study was employed to evaluate micelle aggregation numbers (N agg ), which signify the involvement of surfactant was forever higher compared to IBF. Stern–Volmer binding constants (K sv ), micropolarity (I 1 /I 3 ) and dielectric constant (D exp ) of the mixtures are also obtained using fluorescence method. By the addition of urea raise in the surface charge of the micelles was observed followed by halt of the micellization of drug and surfactant as well as their mixture, therefore cmc values increases followed by decrease in aggregation number. The 1 H NMR resonance intensity variations were paralleled by upfield shifts in the resonance frequencies, due to an increased shielding of IBF happening from closeness of the non-ionic TX-100 surfactant.

  3. Critical micelle concentration of surfactants in aqueous buffered and unbuffered systems

    International Nuclear Information System (INIS)

    Fuguet, Elisabet; Rafols, Clara; Roses, Marti; Bosch, Elisabeth

    2005-01-01

    Critical micelle concentration (CMC) of sodium dodecyl sulphate (SDS), lithium perfluorooctanesulfonate (LPFOS), hexadecyltrimethylammonium bromide (HTAB), tetradecyltrimethylammonium bromide (TTAB), and sodium cholate (SC), surfactants commonly used as pseudostationary phases in micellar electrokinetic chromatography (MEKC), have been determined by means of three different methods: MEKC, spectrophotometry, and conductometry. Determinations have been performed in water, and also in different concentrations of phosphate buffer at pH 7.0. CMC values ranging from 8.08 (water) to 1.99 (50 mM phosphate buffer) mM for SDS, from 7.16 (water) to 2,81 (30 mM phosphate buffer) mM for LPFOS, from 3.77 (water) to 1.93 (20 mM phosphate buffer) mM for TTAB, from 0.91 (water) to ∼0.34 (20 mM phosphate buffer) for HTAB, and around 13 mM (20 mM phosphate buffer) for SC, are obtained. The effect of the electrolyte concentration on the CMC, as well as the linear relationship between the electrolyte counter-ion concentration and the CMC are discussed. This linear relationship provides an easy way for users to estimate the CMC of a MEKC system, at a given electrolyte concentration. A comparison between experimental methods, as well as a discussion about the suitability of a given method for the determination of the CMC for a given surfactant system is also provided

  4. Survival, mobility, and membrane-bound enzyme activities of freshwater planarian, Dugesia japonica, exposed to synthetic and natural surfactants.

    Science.gov (United States)

    Li, Mei-Hui

    2012-04-01

    Surfactants are a major class of emerging pollutants widely used in large quantities in everyday life and commonly found in surface waters worldwide. Freshwater planarian was selected to examine the effects of different surfactants by measuring mortality, mobility, and membrane-bound enzyme activities. Among the 10 surfactants tested, the acute toxicities of betaine and polyethylene glycol (PEG-200) to planarians were relatively low, with a median lethal concentration (LC50) greater than 10,000 mg/L. The toxicity to planarians of the other eight surfactants based on 48-h LC50 could be arranged in the descending order of cetylpyridinum chloride (CPC) > 4-tert-octylphenol (4-tert-OP) > ammonium lauryl sulfate > benzalkonium chloride > saponin > sodium lauroylsarcosinate > dioctyl sulfosuccinate > dodecyl trimethyl ammonium bromide (DTAB). Both CPC and 4-tert-OP were very toxic to planarians, with 48-h LC50 values <1 mg/L. The median effective concentrations (EC50s) of planarian mobility were in the 0.1 to 50 mg/L range and were in the same range as the 24-h LC50 of planarians exposed to different surfactants, except for DTAB. In addition, significant inhibition of cholinesterase activity activities was found in planarians exposed to 4-tert-OP at 2.5 and 5 mg/L and to saponin at 10 mg/L after 2-h treatments. This result suggests that planarian mobility responses can be used as an alternative indicator for acute toxicity of surfactants after a very short exposure period. Copyright © 2012 SETAC.

  5. Surfactant-induced skin irritation and skin repair: evaluation of a cumulative human irritation model by noninvasive techniques.

    Science.gov (United States)

    Wilhelm, K P; Freitag, G; Wolff, H H

    1994-12-01

    Although surfactant-induced acute irritant dermatitis has been extensively studied, our understanding about the induction and repair of the clinically more relevant chronic form is limited. Our purpose was to investigate qualitative and quantitative differences in surfactant-induced irritant skin reactions from cumulative exposure to structurally unrelated surfactants and to compare the maximal irritant responses from this model with corresponding reactions noted in a previously reported acute irritation model. Sodium lauryl sulfate (SLS), dodecyl trimethyl ammonium bromide (DTAB), and potassium soap were the model irritants. Surfactant solutions (7.5%) were applied for 20 minutes daily (for 8 consecutive days excluding the weekend) to the volar aspect of the forearm of 11 volunteers. Irritant reactions were repeatedly assessed until complete healing was indicated by visual assessment and by measurements of transepidermal water loss (TEWL), erythema (skin color reflectance), and stratum corneum hydration (electrical capacitance). Maximum irritant responses were compared with corresponding reactions from an acute irritation model. TEWL was increased by SLS and DTAB to the same extent, but erythema was significantly higher in DTAB-treated skin. Skin dryness, as demonstrated by decreased capacitance values and increased scores for scaling and fissuring, was significantly more pronounced than in an acute irritation model for SLS and DTAB, although no difference was detected between the two surfactants. Potassium soap led to a slight increase in TEWL, whereas the remaining features were not significantly changed. This chronic irritation model appears to represent the clinical situation of irritant contact dermatitis with pronounced skin dryness more closely than the acute irritation model. The present study confirms that an extended time is needed for complete healing of irritant skin reactions. We also demonstrated that the evaluation of the irritation potential of

  6. Mechanism of the immobilization of surfactants on polymeric surfaces by means of an argon plasma treatment: influence of the chemical structure of surfactant substrate

    NARCIS (Netherlands)

    Lens, J.P.; Lens, J.P.; Terlingen, J.G.A.; Terlingen, J.G.A.; Engbers, G.H.M.; Feijen, Jan

    1998-01-01

    In this article, a study on the mechanism of the immobilization of surfactants on polymeric surfaces by means of an argon plasma treatment is described. The unsaturated surfactant sodium 10-undecenoate [C11(:)] and the saturated surfactant sodium dodecanoate (C12) were immobilized on poly(ethylene)

  7. Characterization of sodium bentonites: effect of treatment with ammonium salt- free organic surfactant; Caracterizacao de bentonitas sodicas: efeito do tratamento com surfactante organico livre de sal de amonio

    Energy Technology Data Exchange (ETDEWEB)

    Morita, R. Y.; Barbosa, R. V.; Kloss, J.R., E-mail: julianaweber@utfpr.edu.br [Universidade Tecnologica Federal do Parana (UTFPR), Curitiba, PR (Brazil). Dartamento de Quimica e Biologia

    2015-07-15

    Bentonite, which the main clay mineral is montmorillonite, are commercially attractive because of its abundance in nature. The clays can be modified by ion exchange reactions of ions contained in the interlayer region with cationic surfactants that include ammonium or phosphonium salts. The clays origin and the type of surfactants (modifiers) are the main factors in the alteration of physical and chemical properties of these materials. This study aims to characterize and compare the results of natural bentonite commercially available and the effect of treatments with quaternary ammonium salt and an organic compound free of ammonium salt. The FTIR and XRD results indicate the process of organophilization of clays after treatment with the surfactants. These treatments have altered the average particle size, suggesting the formation of agglomerates, which was showed in the SEM images. The results of surface area and particle size data indicated the presence of larger particles. Although the two surfactants have shown similarities in the investigated properties, the organoclays free of ammonium salt are more promising in terms of its use as well as for their preparation and solubility. (author)

  8. Effect of surfactant concentration in the electrolyte on the tribological properties of nickel-tungsten carbide composite coatings produced by pulse electro co-deposition

    Energy Technology Data Exchange (ETDEWEB)

    Kartal, Muhammet, E-mail: kartal@sakarya.edu.tr [Sakarya University, Engineering Faculty, Metallurgical & Materials Engineering Department, Esentepe Campus, 54187 Sakarya (Turkey); Uysal, Mehmet [Sakarya University, Engineering Faculty, Metallurgical & Materials Engineering Department, Esentepe Campus, 54187 Sakarya (Turkey); Gul, Harun [Duzce University, Gumusova Vocational School, 81850 Duzce (Turkey); Alp, Ahmet; Akbulut, Hatem [Sakarya University, Engineering Faculty, Metallurgical & Materials Engineering Department, Esentepe Campus, 54187 Sakarya (Turkey)

    2015-11-01

    Highlights: • Effect of surfactant concentration on the co-deposited WC was investigated. • In the Ni matrix significantly high hardness was achieved by WC co-deposition. • Optimum surfactant resulted in obtaining superior wear resistance in the Ni. • Friction coefficient was decreased by WC co-deposition in the Ni matrix. - Abstract: A nickel plating bath containing WC particles was used to obtain hard and wear-resistant particle reinforced Ni/WC MMCs on steel surfaces for anti-wear applications. Copper substrates were used for electro co-deposition of Ni matrix/WC with the particle size of <1 μm tungsten carbide reinforcements. The influence of surfactant (sodium dodecyl sulfate, SDS) concentration on particle distribution, microhardness and wear resistance of composite coatings has been studied. The nickel films were characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The effects of the surfactant on the zeta potential, co-deposition and distribution of WC particles in the nickel matrix, as well as the tribological properties of composite coatings were also investigated. The tribological behaviors of the electrodeposited WC composite coatings sliding against M50 steel ball (Ø 10 mm) were examined on a CSM Instrument. All friction and wear tests were performed without lubrication at room temperature and in the ambient air (relative humidity 55–65%).

  9. Genotoxic effects of 2-dodecyl cyclobutanone

    International Nuclear Information System (INIS)

    Delincee, H.; Pool-Zobel, B.L.; Rechkemmer, G.

    1999-01-01

    The paper reports in vivo experiments with rats who received two different doses of 2-dodecyl cyclobutane administered orally. 16 hours after administration, colon cells were isolated and examined for DNA damage by means of the comet assay. No cytotoxic effects were found with the trypan blue exclusion test. When the '% tail intensity' or the 'tail moment' were used for quantitative analysis with the comet assay, it was found that similar results are obtained for the test group which received a lower dose of 2-dodecyl cyclobutane (1.12 mg/kg of body weight) and the control group which received 2% dimethyl sulfoxide. Administration of higher concentrations of the 2-dodecyl cyclobutane (14.9 mg/kg of body weight) was found to induce minor, but significant DNA damage in the test group. Further experiments will be needed in order to assess the relevance of these results for assessment of health risks due to consumption of irradiated food. (orig./CB) [de

  10. Nanocomposite formation between alpha-glucosyl stevia and surfactant improves the dissolution profile of poorly water-soluble drug.

    Science.gov (United States)

    Uchiyama, Hiromasa; Tozuka, Yuichi; Nishikawa, Masahiro; Takeuchi, Hirofumi

    2012-05-30

    The formation of a hybrid-nanocomposite using α-glucosyl stevia (Stevia-G) and surfactant was explored to improve the dissolution of flurbiprofen (FP). As reported previously, the dissolution amount of FP was enhanced in the presence of Stevia-G, induced by the formation of an FP and Stevia-G-associated nanostructure. When a small amount of sodium dodecyl sulfate (SDS) was present with Stevia-G, the amount of dissolved FP was extremely enhanced. This dissolution-enhancement effect was also observed with the cationic surfactant of dodecyl trimethyl ammonium bromide, but not with the non-ionic surfactant of n-octyl-β-D-maltopyranoside. To investigate the dissolution-enhancement effect of Stevia-G/SDS mixture, the pyrene I(1)/I(3) ratio was plotted versus the Stevia-G concentration. The pyrene I(1)/I(3) ratio of Stevia-G/SDS mixture had a sigmoidal curve at lower Stevia-G concentrations compared to the Stevia-G solution alone. These results indicate that the Stevia-G/SDS mixture provides a hydrophobic core around pyrene molecules at lower Stevia-G concentrations, leading to nanocomposite formation between Stevia-G and SDS. The nanocomposite of Stevia-G/SDS showed no cytotoxicity to Caco-2 cells at a mixture of 0.1% SDS and 1% Stevia-G solution, whereas 0.1% SDS solution showed high toxicity. These results suggest that the nanocomposite formation of Stevia-G/SDS may be useful way to enhance the dissolution of poorly water-soluble drugs without special treatment. Copyright © 2012 Elsevier B.V. All rights reserved.

  11. Enhanced recovery and dissolution of griseofulvin nanoparticles from surfactant-free nanocomposite microparticles incorporating wet-milled swellable dispersants.

    Science.gov (United States)

    Bhakay, Anagha; Azad, Mohammad; Vizzotti, Emanuel; Dave, Rajesh N; Bilgili, Ecevit

    2014-11-01

    Nanocomposite microparticles (NCMPs) incorporating drug nanoparticles and wet-milled swellable dispersant particles were investigated as a surfactant-free drug delivery vehicle with the goal of enhancing the nanoparticle recovery and dissolution rate of poorly water-soluble drugs. Superdisintegrants were used as inexpensive, model, swellable dispersant particles by incorporating them into NCMP structure with or without wet-stirred media milling along with the drug. Suspensions of griseofulvin (GF, model drug) along with various dispersants produced by wet-milling were coated onto Pharmatose® to prepare NCMPs in a fluidized bed process. Hydroxypropyl cellulose (HPC, polymer) alone and with sodium dodecyl sulfate (SDS, surfactant) was used as base-line stabilizer/dispersant during milling. Croscarmellose sodium (CCS, superdisintegrant) and Mannitol were used as additional dispersants to prepare surfactant-free NCMPs. Nanoparticle recovery during redispersion and dissolution of the various GF-laden NCMPs were examined. Suspensions prepared by co-milling GF/HPC/CCS or milling GF/HPC/SDS were stable after 30 h of storage. After drying, due to its extensive swelling capacity, incorporation of wet-milled CCS in the NCMPs caused effective breakage of the NCMP structure and bursting of nanoparticle clusters, ultimately leading to fast recovery of the GF nanoparticles. Optimized wet co-milling and incorporation of CCS in NCMP structure led to superior dispersant performance over incorporation of unmilled CCS or physically mixed unmilled CCS with NCMPs. The enhanced redispersion correlated well with the fast GF dissolution from the NCMPs containing either CCS particles or SDS. Overall, swellable dispersant (CCS) particles, preferably in multimodal size distribution, enable a surfactant-free formulation for fast recovery/dissolution of the GF nanoparticles.

  12. Surfactant assisted pulsed two-phase electromembrane extraction followed by GC analysis for quantification of basic drugs in biological samples.

    Science.gov (United States)

    Zahedi, Pegah; Davarani, Saied Saeed Hosseiny; Moazami, Hamid Reza; Nojavan, Saeed

    2016-01-05

    In this work, a simple and efficient surfactant assisted pulsed two-phase electromembrane extraction (SA-PEME) procedure combined with gas chromatography (GC) has been developed for the determination of alfentanil, sufentanil and methadone in various samples. It has been found that the addition of anionic surfactant causes the accumulation of the cationic analytes at the SLM/solution interface resulting in an easier transfer of the analytes into the organic phase. The method was accomplished with 1-octanol as the acceptor phase and supported liquid membrane (SLM) by means of an 80 V pulsed electrical driving force and the extraction time of 20 min. The model analytes were extracted from 3.0 mL sample solution (pH 4.0) containing 0.02% w/v surfactant (sodium dodecyl sulfate). The duty cycle of 92% and frequency of 0.357 Hz gave the best performance. Extraction recoveries in the range of 70.5-95.2% and satisfactory repeatability (7.6samples. Copyright © 2015 Elsevier B.V. All rights reserved.

  13. Investigations of poly(pyrrole)-coated cotton fabrics prepared in blends of anionic and cationic surfactants as flexible electrode

    International Nuclear Information System (INIS)

    Liang, Guijie; Zhu, Ligen; Xu, Jie; Fang, Dong; Bai, Zikui; Xu, Weilin

    2013-01-01

    Highlights: • Poly(pyrrole)-coated cotton fabrics were prepared in mixed surfactants. • The fabrics are soft, lightweight, mechanically robust, and highly electrical conductive. • Potential applications of the fabrics as flexible electrodes were tested. • The fabric electrodes exhibited high discharge capacity and excellent cycling performance. -- Abstract: In recent years, much effort has been dedicated to achieve lightweight, stretchable and flexible energy-storage devices for wearable electronics. Here we report an everyday cotton fabric coated with poly(pyrrole) as flexible electrodes. Poly(pyrrole) nanoparticles are synthesized on the fabrics via a simple chemical polymerization process with the mixed surfactants of cetyltrimethylammonium bromide (CTAB) and sodium dodecyl benzene sulfonate (SDBS) as soft template. A highly conductive fabric with surface resistance of 14 Ω/□ can be produced by changing surfactant concentration. Such a conductive textile shows outstanding flexibility and stretchability, and demonstrates strong adhesion between the PPy and the cellulose fiber. The fabric electrode exhibits a discharge capacity of 51.7 mAh g −1 with high cycling stability (negligible decay after 100 cycles)

  14. Characterisation of thin films of graphene-surfactant composites produced through a novel semi-automated method.

    Science.gov (United States)

    Walch, Nik J; Nabok, Alexei; Davis, Frank; Higson, Séamus P J

    2016-01-01

    In this paper we detail a novel semi-automated method for the production of graphene by sonochemical exfoliation of graphite in the presence of ionic surfactants, e.g., sodium dodecyl sulfate (SDS) and cetyltrimethylammonium bromide (CTAB). The formation of individual graphene flakes was confirmed by Raman spectroscopy, while the interaction of graphene with surfactants was proven by NMR spectroscopy. The resulting graphene-surfactant composite material formed a stable suspension in water and some organic solvents, such as chloroform. Graphene thin films were then produced using Langmuir-Blodgett (LB) or electrostatic layer-by-layer (LbL) deposition techniques. The composition and morphology of the films produced was studied with SEM/EDX and AFM. The best results in terms of adhesion and surface coverage were achieved using LbL deposition of graphene(-)SDS alternated with polyethyleneimine (PEI). The optical study of graphene thin films deposited on different substrates was carried out using UV-vis absorption spectroscopy and spectroscopic ellipsometry. A particular focus was on studying graphene layers deposited on gold-coated glass using a method of total internal reflection ellipsometry (TIRE) which revealed the enhancement of the surface plasmon resonance in thin gold films by depositing graphene layers.

  15. Characterisation of thin films of graphene–surfactant composites produced through a novel semi-automated method

    Directory of Open Access Journals (Sweden)

    Nik J. Walch

    2016-02-01

    Full Text Available In this paper we detail a novel semi-automated method for the production of graphene by sonochemical exfoliation of graphite in the presence of ionic surfactants, e.g., sodium dodecyl sulfate (SDS and cetyltrimethylammonium bromide (CTAB. The formation of individual graphene flakes was confirmed by Raman spectroscopy, while the interaction of graphene with surfactants was proven by NMR spectroscopy. The resulting graphene–surfactant composite material formed a stable suspension in water and some organic solvents, such as chloroform. Graphene thin films were then produced using Langmuir–Blodgett (LB or electrostatic layer-by-layer (LbL deposition techniques. The composition and morphology of the films produced was studied with SEM/EDX and AFM. The best results in terms of adhesion and surface coverage were achieved using LbL deposition of graphene(−SDS alternated with polyethyleneimine (PEI. The optical study of graphene thin films deposited on different substrates was carried out using UV–vis absorption spectroscopy and spectroscopic ellipsometry. A particular focus was on studying graphene layers deposited on gold-coated glass using a method of total internal reflection ellipsometry (TIRE which revealed the enhancement of the surface plasmon resonance in thin gold films by depositing graphene layers.

  16. Surfactant-assisted hydrothermal synthesis of TiO2/reduced graphene oxide nanocomposites and their photocatalytic performances

    Science.gov (United States)

    Hu, Ju; Li, Hansheng; Muhammad, Sohail; Wu, Qin; Zhao, Yun; Jiao, Qingze

    2017-09-01

    Titanium dioxide/reduced graphene oxide nanocomposites (TiO2/RGO-X, X=S, T or C, was denoted sodium dodecyl benzene sulfonate, Triton X-100 and cetyl trimethyl ammonium bromide, respectively) were synthesized using a one-step surfactant-assisted hydrothermal method. The characterization of phase structure and morphology of the as-obtained nanocomposites reveals that TiO2 in the TiO2/RGO-X exhibits the morphologies of nanoparticles, nanowires and array-like nanowires on the surface of RGO, respectively. Compared with the control TiO2/RGO nanocomposite, TiO2/RGO-X presents an excellent photocatalytic activity. With uniform array-like TiO2 nanowires on the surface of RGO, the TiO2/RGO-C shows a significant enhancement in the photocatalytic efficiency. Besides, a deeper insight into the growth mechanism of TiO2/RGO nanocomposites is put forward. This work indicates that the surfactant-assisted hydrothermal method is an effective approach to improve the structure, morphology and photocatalytic performance of TiO2/RGO composites. Moreover, the surfactants with various types can interact with the precursors of TiO2 and RGO in different ways.

  17. Characteristics of SF{sub 6} gas hydrate formation mechanisms (kinetics) and surfactants effects on hydrate formation rate

    Energy Technology Data Exchange (ETDEWEB)

    Lee, B.; Lee, H.; Kim, Y.D. [Pusan National Univ., Busan (Korea, Republic of). School of Materials Science and Engineering; Kim, Y.S.; Lee, J.D. [Korea Inst. of Industrial Technology, Busan (Korea, Republic of). Advanced Energy Resource Development Team

    2008-07-01

    Sulfur hexafluoride (SF{sub 6}) is used as an insulating gas in a variety of industrial applications, and is a potent greenhouse gas (GHG). Gas hydrates are stable crystalline compounds formed by water and natural gas molecules that have relatively large cavities that can be occupied by guest molecules. SF{sub 6} gas is able to form hydrates at relatively mild conditions. This study investigated the hydrate formation mechanisms of SF{sub 6} gas, and presented a potential hydration treatment for the gas. The effects of surface active agents on SF{sub 6} gas hydrate formation were examined experimentally using Tween 20, sodium dodecyl sulfate (SDS) and linear alkyl benzene sulfonate (LABS). The surfactants showed promoter behaviour for SF{sub 6} gas hydrate formation. Formation rates occurred in 2 stages, with rates rapidly increasing during the second phase. The inflection point occurred approximately 30 minutes after the hydrate nucleation point. Results indicated the existence of a critical concentration of surfactants. It was concluded that SF{sub 6} gas hydrate formation rates were increased by the addition of surfactants. Further studies are needed to investigate 2-stage hydrate formation rates. 18 refs., 4 figs.

  18. Hexafluoroisopropanol-induced catanionic-surfactants-based coacervate extraction for analysis of lysozyme.

    Science.gov (United States)

    Xu, Jia; Niu, Manli; Xiao, Yuxiu

    2017-02-01

    A coacervate extraction method, based on hexafluoroisopropanol (HFIP)-induced catanionic surfactants and coupled with a back-extraction procedure, was developed for separation and purification of proteins, using sodium dodecyl sulfate (SDS) and dodecyltrimethyl ammonium bromide (DTAB) as representative catanionic surfactants and lysozyme as a model protein. After the coacervate extraction and back extraction, the obtained lysozyme solutions were examined in terms of quantitative analysis by capillary electrophoresis, bacteriolytic activity, and circular dichroism (CD). The effects of several parameters including back-extraction solvent, HFIP content, total surfactant concentration, and SDS/DTAB molar ratio were investigated in detail on the extraction efficiency and activity of lysozyme. Under the optimized extraction conditions (66 mM KH 2 PO 4 buffer with pH 6.2 as back-extraction solvent, SDS/DTAB molar ratio = 1:1 mol/mol, total surfactant concentration = 30 mM, HIFP concentration = 8 % v/v), the extraction recovery was 89.8 % (±4.7, n = 3), limit of detection was 2.2 (±0.3, n = 3) μg mL -1 , and meanwhile nearly 65 % of native lysozyme activity was retained. In addition, the activity and CD assays showed that SDS/DTAB molar ratio had a significant influence on the activity and structure of lysozyme after extraction. The DTAB-rich extraction systems, in which the DTAB mole fraction was equal to or larger than 70 %, could keep the activity and structure of lysozyme almost in the native state. Graphical Abstract Procedure of HFIP-induced SDS/DTAB coacervate extraction and back extraction of lysozyme.

  19. Influence of puerperium on the serum proteins of Saanen goats, obtained by the analysis of electrophoresis on sodium dodecyl sulphate-polyacrylamide gel / Influência do puerpério sobre o proteinograma sérico de caprinos da raça Saanen obtido por eletroforese em gel de poliacrilamida

    Directory of Open Access Journals (Sweden)

    Eduardo Harry Birgel Junior

    2009-10-01

    Full Text Available Aiming to evaluate the puerperal influence on the proteinogram of Saanen goats, 108 samples of blood serum from 12 goats were collected, and the results were presented at nine times: just after parturition, 1, 3, 5, 7, 10, 15, 21 and 30 days after parturition. Total amount of serum proteins were determined by the biuret technique, and the sodium dodecyl sulphate-polyacrylamide gel electrophoresis (SDS-PAGE was used to the protein fractionation. In this last method, 17 protein bands were observed, from which molecular weights varied between 25 KDa and 275 KDa. In addition, it was possible to identify the following protein fractions: immunoglobulin A (180 KDa, ceruloplasmin (115 KDa, transferrin (79 KDa, albumin (65 KDa, heavy-chain immunoglobulin G (58 KDa, haptoglobin (45 KDa, acid glycoprotein (37 KDa and light-chain immunoglobulin G (28 KDa. Another 9 nonidentified protein fractions presented, each molecular weights equal to 275 KDa, 140 KDa, 125 KDa, 103 KDa, 95 KDa, 41 KDa, 35 KDa, 30 Kda and 25 KDa. The results allow us to conclude that by the first week of puerperium, an improvement of acid glycoprotein occurs, whereas those others protein fractions do not suffer any puerperal influence.Com o objetivo de avaliar a influência do puerpério no proteinograma de caprinos da raça Saanen foram colhidas 108 amostras de soro sangüíneo de 12 cabras, sendo os resultados apresentados em nove momentos: imediatamente após a parição, 1, 3, 5, 7, 10, 15, 21 e 30 dias após o parto. Os teores séricos de proteína total foram determinados pela técnica do biureto, e para o fracionamento das proteínas foi realizada a eletroforese em gel de poliacrilamida contendo dodecil sulfato de sódio (SDS-PAGE. No método utilizado foram observadas 17 bandas protéicas, cujos pesos moleculares (PM variaram de 25 KDa a 275 KDa, sendo possível a identificação das seguintes frações protéicas: imunoglobulina A (180 KDa, ceruloplasmina (115 KDa, transferrina

  20. O/W emulsions stabilised by both low molecular weight surfactants and colloidal particles: The effect of surfactant type and concentration.

    Science.gov (United States)

    Pichot, R; Spyropoulos, F; Norton, I T

    2010-12-01

    The stability against coalescence of O/W emulsions in the presence of both surfactants and colloidal particles was investigated. In particular the effect of the surfactant type and concentration in these emulsifier mixtures on the O/W emulsions' stability was studied. Two types of surfactants were selected; those that have the ability to stabilise O/W emulsions on their own (O/W surfactants) and those that cannot (W/O surfactants). Tween 60 and Sodium Caseinate were selected as the O/W surfactants and lecithin as the W/O surfactant. Oil-in-water emulsions prepared with both particles and any of the three surfactants were stable against coalescence but, depending on the type of surfactant, the behaviour of the systems was found to depend on surfactant concentration. The droplet sizes of emulsions stabilised by mixed emulsifier systems containing low concentrations of O/W surfactants (Tween 60 or Sodium Caseinate) were smaller than those solely stabilised by either the surfactant or particles alone. At intermediate O/W surfactants concentrations, the droplet sizes of the emulsions increased. Further increases in the O/W surfactants' concentration, resulted in the complete removal of particles from the interface with the system now behaving as a surfactant-only stabilised emulsion. The behaviour of emulsions stabilised by emulsifier mixtures containing W/O surfactants was not dependent on the concentration of surfactant: no removal of particles was observed. Copyright © 2010 Elsevier Inc. All rights reserved.

  1. Adsorption of dimeric surfactants in lamellar silicates

    Energy Technology Data Exchange (ETDEWEB)

    Balcerzak, Mateusz; Pietralik, Zuzanna [Department of Macromolecular Physics, Faculty of Physics, A. Mickiewicz University, Umultowska 85, 61-614 Poznań (Poland); Domka, Ludwik [Department of Metalorganic Chemistry, Faculty of Chemistry, A. Mickiewicz University, Grunwaldzka 6, 60-780 Poznań (Poland); Skrzypczak, Andrzej [Institute of Chemical Technology, Poznań University of Technology, Berdychowo 4, 60-965 Poznań (Poland); Kozak, Maciej, E-mail: mkozak@amu.edu.pl [Department of Macromolecular Physics, Faculty of Physics, A. Mickiewicz University, Umultowska 85, 61-614 Poznań (Poland)

    2015-12-01

    Highlights: • The intercalation of dimeric surfactants changed the morphology of MMT samples. • XRD indicated structures formed by surfactant molecules in interlayer space. • The four-step thermal decomposition of dimeric surfactant, confirms intercalation. - Abstract: The adsorption of different types of cationic surfactants in lamellar silicates changes their surface character from hydrophilic to hydrophobic. This study was undertaken to obtain lamellar silicates modified by a series of novel dimeric (gemini) surfactants of different length alkyl chains and to characterise these organophilised materials. Synthetic sodium montmorillonite SOMASIF® ME 100 (M) and enriched bentonite of natural origin (Nanoclay – hydrophilic bentonite®) were organophilised with dimeric (gemini) surfactants (1,1′-(1,4-butanediyl)bis(alkoxymethyl)imidazolium dichlorides). As a result of surfactant molecule adsorption in interlamellar space, the d-spacing (d{sub 001}) increased from 0.97 nm (for the anhydrous structure) to 2.04 nm. A Fourier transform infrared spectroscopy (FTIR) analysis of the modified systems reveals bands assigned to the stretching vibrations of the CH{sub 2} and CH{sub 3} groups and the scissoring vibrations of the NH group from the structure of the dimeric surfactants. Thermogravimetric (TG) and derivative thermogravimetric (DTG) studies imply a four-stage process of surfactant decomposition. Scanning electron microscopy (SEM) images provide information on the influence of dimeric surfactant intercalation into the silicate structures. Particles of the modified systems show a tendency toward the formation of irregularly shaped agglomerates.

  2. Surfactant Assisted Stabilization of Carbon Nanotubes Synthesized by a Spray Pyrolysis Method

    Directory of Open Access Journals (Sweden)

    D. Mendoza-Cachú

    2017-01-01

    Full Text Available Surface modification of carbon nanotubes has been an interesting issue from a composites materials point of view. A nanotubes agglomeration has to be avoided to achieve a homogeneous dispersion in a composite matrix. In this research, we report on the synthesis of carbon nanotubes using a variant of the chemical vapor deposition technique known as spray pyrolysis method. X-ray diffraction (XRD, transmission electron microscopy (TEM, and scanning electron microscopy (SEM studies showed that the synthesized products had an aligned structure with low purity degree, high content of catalyst particles, and a smaller amount of amorphous carbon. A secondary method was applied, which involves an acidic treatment that dissolves contaminant particles to enhance the purity of the nanotubes. Microstructural analysis, which includes XRD and SEM, indicates an effective reduction of impurities. Dispersion of the nanotubes was assessed using different surfactants, such as sodium dodecyl-sulfate (SDS and ethylenediaminetetraacetic acid (EDTA. Finally, Raman spectroscopy, UV-Vis, and SEM techniques confirm that better results were obtained with EDTA. For EDTA and SDS surfactants, low concentrations of 0.3 mg/mL and 0.2 mg/mL were most efficient, respectively.

  3. Surface and micellar properties of Chloroquine Diphosphate and its interactions with surfactants and Human Serum Albumin

    International Nuclear Information System (INIS)

    Usman, Muhammad; Siddiq, Mohammad

    2013-01-01

    Highlights: ► Free energy of adsorption is more negative than free energy of micellization. ► Shifts in UV/Visible spectra in presence of SDS indicated interaction of CLQ with SDS. ► The decrease in fluorescence intensity of HSA by CLQ shows its binding with HSA. -- Abstract: This manuscript addresses the physicochemical behavior of an antimalarial drug Chloroquine Diphosphate (CLQ) as well as its interaction with anionic surfactants and Human Serum Albumin (HSA). Surface tension and specific conductivity were employed to detect the critical micelle concentration (CMC) and thus its surface and thermodynamic parameters were calculated. Solubilization of this drug within micelles of anionic surfactant sodium dodecyl sulfate (SDS) has also been studied. UV/Visible spectroscopy was used to calculate partition coefficient (K x ), free energy of partition and number of drug molecules per micelle. The complexation of drug with HSA at physiological conditions (pH 7.4) has also been analyzed by using UV/Visible and fluorescence spectroscopy. The values of drug-protein binding constant, number of binding sites and free energy of binding were calculated

  4. Determination of Sudan I-IV in candy using ionic liquid/anionic surfactant aqueous two-phase extraction coupled with high-performance liquid chromatography.

    Science.gov (United States)

    Yu, Wei; Liu, Zhongling; Li, Qiang; Zhang, Hanqi; Yu, Yong

    2015-04-15

    Ionic liquid/anionic surfactant aqueous two-phase system was developed and applied for the extraction of Sudan I-IV. High-performance liquid chromatography was applied to the determination of the analytes. The aqueous two-phase system (ATPS) was formed in the present of C4[MIM]BF4, sodium dodecyl benzene sulphonate and (NH4)2SO4. The parameters affecting the extraction efficiency, such as volume of ionic liquid, amount of sodium dodecyl benzene sulphonate, ionic strength, pH value of system, extraction time and temperature were investigated. The limits of detection for Sudan I, II, III and IV were 5.45, 4.66, 3.68, 4.20 μg kg(-1), respectively. When the present method was applied to the analysis of candy samples, the recoveries of the analytes ranged from 82.3% to 112.1% and relative standard deviations were lower than 7.41%. Copyright © 2014 Elsevier Ltd. All rights reserved.

  5. Mesoporous film of WO{sub 3}–the “sunlight” assisted decomposition of surfactant in wastewater for voltammetric determination of Pb

    Energy Technology Data Exchange (ETDEWEB)

    Krasnodębska-Ostręga, Beata, E-mail: bekras@chem.uw.edu.pl; Bielecka, Agnieszka; Biaduń, Ewa; Miecznikowski, Krzysztof, E-mail: kmiecz@chem.uw.edu.pl

    2016-12-01

    Highlights: • The “sun light” decomposed of surfactants: Sodium dodecyl sulfate and Triton™X-114 in the presence of WO{sub 3}. • Mesoporous WO{sub 3} films use for the degradation of surfactant without any reagents. • The developed procedure is suggested to be a no-reagents method of decomposition of added SDS leads to 100% recovery of added Pb (II). - Abstract: In this paper we present the application of “sunlight” assisted digestion in the presence of WO{sub 3} to the decomposition of dissolved organic matter, using the anionic surfactant sodium dodecyl sulfate (SDS) and the nonionic surfactant (1,1,3,3-tetramethylbutyl)phenyl-polyethylene glycol (Triton™X-114) in natural water samples, prior to the determination of traces residues of lead by stripping voltammetry methods. The results of the study showed firstly that the preparation of reproducible WO{sub 3} layers characterized by high mechanical and chemical resistance was possible, and secondly that it was also possible to obtain a high efficiency of decomposition, equal in efficiency to that of the reference method, which was the hydrogen peroxide oxidation assisted by UV, with evaporation nearly to dryness. The developed procedure is suggested to be a no-reagents method for the decomposition of added SDS, leading to 100% recovery of added Pb (II). The anodic stripping voltammetric curves recorded in solution after 4 h irradiation with UV assisted by WO{sub 3} were repeatable and increased linearly with standard additions, but the data finally obtained were incorrect. The curves recorded in solution after “sunlight” assisted digestion in the presence of WO{sub 3} were repeatable, and increased linearly with an increasing of concentration of standard additions (100% recovery of Pb). In the case of a nonionic surfactant, the decomposition time is at least 6 h. The advantage of the proposed method is the fact that the digestion process does not need the addition of any chemicals for the

  6. Sodium Dedecyl Suphate Polyacrilamide Gel Electrophosis of ...

    African Journals Online (AJOL)

    Sodium Dedecyl Suphate Polyacrilamide Gel Electrophosis of Campylobacter coli. S.I. Smith, M.M. Ibrahim, V.N. Ezeobi, K.S. Oyedeji, K.A. Akinsinde, A.O Coker. Abstract. Campylobacter coli were characterized using sodium dodecyl sulphate-polyacrilamide gel electrophoresis (SDS-PAGE). The isolates were obtained ...

  7. Interactions of cationic trimeric, gemini and monomeric surfactants with trianionic curcumin in aqueous solution.

    Science.gov (United States)

    Wang, Meina; Wu, Chunxian; Tang, Yongqiang; Fan, Yaxun; Han, Yuchun; Wang, Yilin

    2014-05-21

    Interactions of trianionic curcumin (Cur(3-)) with a series of cationic surfactants, monomeric surfactant dodecyl trimethylammonium bromide (DTAB), dimeric surfactant hexamethylene-1,6-bis(dodecyldimethylammonium bromide) (12-6-12) and trimeric surfactant tri(dodecyldimethylammonioacetoxy)diethyltriamine trichloride (DTAD), have been investigated in aqueous solution of pH 13.0. Surface tension and spectral measurements indicate that the cationic surfactants display a similar surfactant concentration dependent interaction process with Cur(3-), involving three interaction stages. At first the three cationic surfactants electrostatically bind on Cur(3-) to form the surfactant-Cur(3-) complex. Then the bound and unbound cationic surfactants with Cur(3-) aggregate into surfactant-Cur(3-) mixed micelles through hydrophobic interactions above the critical micelle concentration of the surfactants (CMCC) in the presence of Cur(3-). Finally excess unbound surfactants self-assemble into micelles like those without Cur(3-). For all the three surfactants, the addition of Cur(3-) only decreases the critical micelle concentration of 12-6-12 but does not affect the critical micelle concentration of DTAB and DTAD. As the oligomeric degree of surfactants increases, the intermolecular interaction of the cationic surfactants with Cur(3-) increases and the surfactant amount needed for Cur(3-) encapsulation decreases. Compared with 12-6-12, either the weaker interaction of DTAB with Cur(3-) or stronger interaction of DTAD with Cur(3-) limits the stability or solubility of Cur(3-) in surfactant micelles. Therefore, gemini surfactant 12-6-12 is the best choice to effectively suppress Cur(3-) degradation at very low concentrations. Isothermal titration microcalorimetry, surface tension and (1)H NMR results reveal that 12-6-12 and Cur(3-) form a (12-6-12)2-Cur(3-) complex and start to form micelles at extremely decreased concentrations, where either 12-6-12 or Cur(3-) works as a bridge

  8. Improving pure red upconversion emission of Co-doped Y{sub 2}O{sub 3}:Yb{sup 3+}–Er{sup 3+} nanocrystals with a combination of sodium sulfide and surfactant Pluronic-F127

    Energy Technology Data Exchange (ETDEWEB)

    López-Luke, T., E-mail: tzarara@cio.mx [Centro de Investigaciones en Óptica, A.P. 1-948, León, Gto. 37160, México (Mexico); De la Rosa, E., E-mail: elder@cio.mx [Centro de Investigaciones en Óptica, A.P. 1-948, León, Gto. 37160, México (Mexico); Campos Villalobos, I. [Centro de Investigaciones en Óptica, A.P. 1-948, León, Gto. 37160, México (Mexico); Rodriguez, R.A. [Universidad de Guadalajara, Unidad Lagos, Lagos de Moreno, Jal. 47460, México (Mexico); Ángles-Chávez, C. [Instituto Mexicano del Petróleo, Cd. México, D.F. 07730, México (Mexico); Salas, P. [Centro de Física Aplicada y Tecnología Avanzada, Universidad Nacional Autónoma de México, A.P. 1-1010, Querétaro, Qro. 76000, México (Mexico); Wheeler, Damon A.; Zhang, J.Z. [Department of Chemistry and Biochemistry, University of California, Santa Cruz, CA 95064 (United States)

    2014-01-15

    Nanocrystals of Y{sub 2}O{sub 3}:Yb{sup 3+}–Er{sup 3+} (2:1 mol% Yb{sup 3+}:Er{sup 3+}) were prepared by a novel precipitation technique using Na{sub 2}S and Pluronic-F127 (PF127) surfactant. Crystal structure, particle size, red emission intensity and fluorescence decay lifetimes were determined using microscopy and spectroscopy techniques. TEM analysis indicates that the average particle size ranged from 40 to 70 nm. The nanocrystals showed a strong red emission band centered at 663 nm after excitation at 970 nm. The upconverted signal intensity was improved 250% with an optimum concentration of Na{sub 2}S (0.48 M) and PF127 (0.1 mM). The improvement was explained in terms of the reduction of surface contaminants as well as the cubic crystalline phase of the parent Y{sub 2}O{sub 3} material. Interestingly, the formation of sulfates (SO{sub 4}{sup 2−}) is faster than that of O–H, which is responsible for quenching the red and green emissions. The results suggest that Na{sub 2}S and PF127 are good candidates for surface passivation, especially when used in conjunction. The preparation of Y{sub 2}O{sub 3}:Yb{sup 3+}–Er{sup 3+} using Na{sub 2}S with strong red emission band was produced at a lower cost than that of other sulfuration processes. -- Highlights: • . • Strong red emission band centered at 663 nm was obtained after excitation at 970 nm. • Yb-Er codoped Y2O3 nanocrystals with average size ranging from 40 to 70 nm. • Improvement of the red emission in Y2O3:Yb-Er nanocrystals by the introduction of sodium sulfide and pluronic. • Passivation of nanocrystal surface with sodium sulfide and pluoronic.

  9. Layer-by-Layer Assembly of Fluorine-Free Polyelectrolyte-Surfactant Complexes for the Fabrication of Self-Healing Superhydrophobic Films.

    Science.gov (United States)

    Wu, Mengchun; An, Ni; Li, Yang; Sun, Junqi

    2016-11-29

    Fluorine-free self-healing superhydrophobic films are of significance for practical applications because of their extended service life and cost-effective and eco-friendly preparation process. In this study, we report the fabrication of fluorine-free self-healing superhydrophobic films by layer-by-layer (LbL) assembly of poly(sodium 4-styrenesulfonate) (PSS)-1-octadecylamine (ODA) complexes (PSS-ODA) and poly(allylamine hydrochloride) (PAH)-sodium dodecyl sulfonate (SDS) (PAH-SDS) complexes. The wettability of the LbL-assembled PSS-ODA/PAH-SDS films depends on the film structure and can be tailored by changing the NaCl concentration in aqueous dispersions of PSS-ODA complexes and the number of film deposition cycles. The freshly prepared PSS-ODA/PAH-SDS film with micro- and nanoscaled hierarchical structures is hydrophilic and gradually changes to superhydrophobic in air because the polyelectrolyte-complexed ODA and SDS surfactants tend to migrate to the film surface to cover the film with hydrophobic alkyl chains to lower its surface energy. The large amount of ODA and SDS surfactants loaded in the superhydrophobic PSS-ODA/PAH-SDS films and the autonomic migration of these surfactants to the film surface endow the resultant superhydrophobic films with an excellent self-healing ability to restore the damaged superhydrophobicity. The self-healing superhydrophobic PSS-ODA/PAH-SDS films are mechanically robust and can be deposited on various flat and nonflat substrates. The LbL assembly of oppositely charged polyelectrolyte-surfactant complexes provides a new way for the fabrication of fluorine-free self-healing superhydrophobic films with satisfactory mechanical stability, enhanced reliability, and extended service life.

  10. Influence of the Surfactant Nature on the Occurrence of Self-Assembly between Rubber Particles and Thermally Reduced Graphite Oxide during the Preparation of Natural Rubber Nanocomposites

    Directory of Open Access Journals (Sweden)

    Héctor Aguilar-Bolados

    2015-01-01

    Full Text Available The natural rubber (NR latex consists of polymer particles charged negatively due to the adsorbed phospholipids and proteins molecules. The addition of stable aqueous suspension of thermally reduced graphite oxide (TRGO stabilized by ionic surfactants to NR latex can favor the occurrence of interaction between the stabilized TRGO and NR particles. Herein, the use of two surfactants of different nature, namely, sodium dodecyl sulfate (SDS and dodecyltrimethylammonium bromide (DTAB, for the preparation of (TRGO/NR nanocomposites, is reported. Zeta potential and particle size measurements indicated that the use of DTAB as cationic surfactant results in the flocculation of NR particles and promoted the formation of ion-pair interactions between TRGO and the proteins and/or phospholipids present on the NR surface. This indicates that the use of DTAB can promote a self-assembly phenomenon between TRGO with adsorbed DTAB molecules and NR particles. The occurrence of self-assembly phenomenon allows obtaining homogenous dispersion of TRGO particles in the polymer matrix. The TRGO/NR nanocomposites prepared by the use of DTAB exhibited superior mechanical properties and excellent electrical conductivities reaching values of stress at 500% strain of 3.02 MPa and 10−4 S/cm, respectively.

  11. A Multi-Constituent Site-Blocking Approach for Modeling the Transport of CuO Nanoparticles and Co-injected Surfactant in Porous Media

    Science.gov (United States)

    Rahman, S. A. B.; Taghavy, A.

    2017-12-01

    Copper oxide nanoparticles (nCu) are used in a wide array of industrial applications and as biocidal alternatives for water treatment. Toxicity studies indicate that nano-sized copper oxide is more potent in both DNA damage and cytotoxicity, due to larger specific surface area, than micrometer sized particles, and that their release into the environment may pose a risk to the aquatic and subsurface environment. Despite the risk, very little effort has been directed at characterization of the mobility aspect of nCuO. In light of the experimental findings of Jeong and Kim (2009) on the transport of nCuO aggregates, we incorporate a multi-constituent site blocking (MCB) approach presented in Becker et al. (2015) into an existing nanoparticle transport simulator, HELP-1D, to simulate the transport and retention of nCuO in porous media in presence of sodium dodecyl sulfate surfactant. A sensitivity study is conducted to explore the effect of variations in physicochemical properties of flow, the injected fluid composition, porous medium, and particles on the deposition kinetics of nCuO. This includes, among other factors, flow velocity, mean particle size, and input concentrations of particle and surfactant, as well as the filtration and site-blocking parameters. Results suggest an acceleration of nCuO transport subsequent to increasing the flow velocity, particle size, and influent concentration of both nCuO and surfactant.

  12. Is the combination of cellulosic polymers and anionic surfactants a good strategy for ensuring physical stability of BCS Class II drug nanosuspensions?

    Science.gov (United States)

    Bilgili, Ecevit; Li, Meng; Afolabi, Afolawemi

    2016-01-01

    Ensuring the physical stability of drug nanosuspensions prepared via wet media milling has been a challenge for pharmaceutical scientists. The aim of this study is to assess the combined use of non-ionic cellulosic polymers and anionic surfactants in stabilizing multiple drug nanosuspensions. Particle size of five drugs, i.e. azodicarbonamide (AZD), fenofibrate (FNB), griseofulvin (GF), ibuprofen (IBU) and phenylbutazone (PB) was reduced separately in an aqueous solution of hydroxypropyl cellulose (HPC) with/without sodium dodecyl sulfate (SDS) via a stirred media mill. Laser diffraction, scanning electron microscopy, thermal analysis, rheometry and electrophoresis were used to evaluate the breakage kinetics, storage stability, electrostatic repulsion and stabilizer adsorption. Without SDS, drug particles exhibited aggregation to different extents; FNB and GF particles aggregated the most due to low zeta potential and insufficient steric stabilization. Although aggregation in all milled suspensions was reduced due to HPC-SDS combination, FNB and IBU showed notable growth during 7-day storage. It is concluded that the combination of non-ionic cellulosic polymers and anionic surfactants is generally viable for ensuring the physical stability of wet-milled drug nanosuspensions, provided that the surfactant concentration is optimized to mitigate the Ostwald ripening, whereas cellulosic polymers alone may provide stability for some drug suspensions.

  13. Modification of Novel Conductive PEDOT:Sulfonated Polyimide Nano-Thin Films by Anionic Surfactant and Poly(vinyl alcohol) for Electronic Applications

    Science.gov (United States)

    Romyen, Nathavat; Thongyai, Supakanok; Praserthdam, Piyasan; Sotzing, Gregory A.

    2013-12-01

    Conductive poly(3,4-ethylenedioxythiophene):sulfonated polyimide (PEDOT: SPI) nanoscale thin films were successfully developed by addition of anionic surfactant and poly(vinyl alcohol) (PVA) for potential application in electronic devices. In this work, sodium dodecyl sulfate (SDS) surfactant was introduced into PEDOT:SPI aqueous suspensions to improve the dispersion stability of the particles in water, leading to high transparency and low contact angle of PEDOT:SPI thin films. All of the conducting polymer thin films showed high transparency of more than 85% transmission. Conductivity enhancement and good film-formation properties of PEDOT:SPI were achieved by adding various amounts of PVA to each polymer aqueous suspension because of the resulting conformational changes. The highest conductivity of 0.134 S/cm was achieved at 0.08 wt.% PVA in PEDOT:SPI2/SDS/PVA film, increased by a factor of 3.5 compared with the original material. In addition, PVA also improved the thermal stability of the conductive films, as verified by thermogravimetric analysis (TGA). The interactions between conducting polymers, PVA, and SDS surfactant affecting nano-thin film properties were revealed and investigated. Moreover, the interactions between SDS and SPI were proven to be different from those between SDS and poly(styrenesulfonate) (PSS) in conventional PEDOT:PSS solutions.

  14. Mixed micelles of polyethylene glycol (23) lauryl ether with ionic surfactants studied by proton 1D and 2D NMR.

    Science.gov (United States)

    Gao, Hong-Chang; Zhao, Sui; Mao, Shi-Zhen; Yuan, Han-Zhen; Yu, Jia-Yong; Shen, Lian-Fang; Du, You-Ru

    2002-05-01

    (1)H NMR chemical shift, spin-lattice relaxation time, spin-spin relaxation time, self-diffusion coefficient, and two-dimensional nuclear Overhauser enhancement (2D NOESY) measurements have been used to study the nonionic-ionic surfactant mixed micelles. Cetyl trimethyl ammonium bromide (CTAB) and sodium dodecyl sulfate (SDS) were used as the ionic surfactants and polyethylene glycol (23) lauryl ether (Brij-35) as the nonionic surfactant. The two systems are both with varying molar ratios of CTAB/Brij-35 (C/B) and SDS/Brij-35 (S/B) ranging from 0.5 to 2, respectively, at a constant concentration of 6 mM for Brij-35 in aqueous solutions. Results give information about the relative arrangement of the surfactant molecules in the mixed micelles. In the former system, the trimethyl groups attached to the polar heads of the CTAB molecules are located between the first oxy-ethylene groups next to the hydrophobic chains of Brij-35 molecules. These oxy-ethylene groups gradually move outward from the hydrophobic core of the mixed micelle with an increase in C/B in the mixed solution. In contrast to the case of the CTAB/Triton X-100 system, the long flexible hydrophilic poly oxy-ethylene chains, which are in the exterior part of the mixed micelles, remain coiled, but looser, surrounding the hydrophobic core. There is almost no variation in conformation of the hydrophilic chains of Brij-35 molecules in the mixed micelles of the SDS/Brij-35 system as the S/B increases. The hydrophobic chains of both CTAB and SDS are co-aggregated with Brij-35, respectively, in their mixed micellar cores.

  15. Exogenous Pulmonary Surfactant as a Vehicle for Antimicrobials: Assessment of Surfactant-Antibacterial Interactions In Vitro

    Directory of Open Access Journals (Sweden)

    Alexei Birkun

    2014-01-01

    Full Text Available Owing to its unique surface-active properties, an exogenous pulmonary surfactant may become a promising drug delivery agent, in particular, acting as a vehicle for antibiotics in topical treatment of pneumonia. The purpose of this study was to assess a mutual influence of natural surfactant preparation and three antibiotics (amikacin, cefepime, and colistimethate sodium in vitro and to identify appropriate combination(s for subsequent in vivo investigations of experimental surfactant/antibiotic mixtures. Influence of antibiotics on surface-active properties of exogenous surfactant was assessed using the modified Pattle method. Effects of exogenous surfactant on antibacterial activity of antimicrobials against Staphylococcus aureus, Klebsiella pneumoniae, and Pseudomonas aeruginosa were evaluated using conventional microbiologic procedures. Addition of amikacin or cefepime to surfactant had no significant influence on surface-active properties of the latter. Obvious reduction of surface-active properties was confirmed for surfactant/colistimethate composition. When suspended with antibiotics, surfactant either had no impact on their antimicrobial activity (amikacin or exerted mild to moderate influence (reduction of cefepime bactericidal activity and increase of colistimethate bacteriostatic activity against S. aureus and P. aeruginosa. Considering favorable compatibility profile, the surfactant/amikacin combination is advisable for subsequent investigation of joint surfactant/antibacterial therapy in animals with bacterial pneumonia.

  16. Exogenous Pulmonary Surfactant as a Vehicle for Antimicrobials: Assessment of Surfactant-Antibacterial Interactions In Vitro

    Science.gov (United States)

    2014-01-01

    Owing to its unique surface-active properties, an exogenous pulmonary surfactant may become a promising drug delivery agent, in particular, acting as a vehicle for antibiotics in topical treatment of pneumonia. The purpose of this study was to assess a mutual influence of natural surfactant preparation and three antibiotics (amikacin, cefepime, and colistimethate sodium) in vitro and to identify appropriate combination(s) for subsequent in vivo investigations of experimental surfactant/antibiotic mixtures. Influence of antibiotics on surface-active properties of exogenous surfactant was assessed using the modified Pattle method. Effects of exogenous surfactant on antibacterial activity of antimicrobials against Staphylococcus aureus, Klebsiella pneumoniae, and Pseudomonas aeruginosa were evaluated using conventional microbiologic procedures. Addition of amikacin or cefepime to surfactant had no significant influence on surface-active properties of the latter. Obvious reduction of surface-active properties was confirmed for surfactant/colistimethate composition. When suspended with antibiotics, surfactant either had no impact on their antimicrobial activity (amikacin) or exerted mild to moderate influence (reduction of cefepime bactericidal activity and increase of colistimethate bacteriostatic activity against S. aureus and P. aeruginosa). Considering favorable compatibility profile, the surfactant/amikacin combination is advisable for subsequent investigation of joint surfactant/antibacterial therapy in animals with bacterial pneumonia. PMID:24876994

  17. Photophysics of a solvent sensitive keto-tetrahydrocarbazole based fluorophore and its interaction with triethylamine: A spectroscopic inquest under surfactant and β-CD confinement

    Science.gov (United States)

    Mitra, Amrit Krishna; Ghosh, Sujay; Sarangi, Manas Kumar; Chakraborty, Suchandra; Saha, Chandan; Basu, Samita

    2014-09-01

    In this communication, we wish to report solution phase photophysics of 6,7-dimethoxy-3-methyl-2,3,4,9-tetrahydro-1H-carbazol-1-one (DMMTCO) and its interaction with a simple aliphatic organic donor, triethylamine (TEA) in different environments using absorption, steady-state and time-resolved fluorescence techniques. We have chosen ten solvents of varied nature and have observed that the fluorescence emission maximum of the compound is sensitive to the ET(30) value of the solvent. Quantum yield of the fluorophore is found to be higher in polar aprotic solvents like DMSO, DMF and ACN. When the fluorophore interacts with an anionic surfactant solution of sodium dodecyl sulphate (SDS), a hypsochromic shift of 17 nm is observed with respect to pure aqueous medium as the concentration of the surfactant increases. On switching over to the neutral surfactant of Triton X-100, a hypsochromic shift of 29 nm with respect to pure aqueous medium is witnessed as the concentration surges. Likewise, with the increase in concentration of β-cyclodextrin, we have noted a hypsochromic shift of 26 nm. In all of the above mentioned occasions, we have perceived hypsochromic shifts along with concomitant increase in fluorescence intensity. These observations regarding the organised media indicate that the immediate surrounding around the probe gets modified with the increase in surfactant and β-cyclodextrin concentration. TEA is a simple organic molecule that interacts with DMMTCO in a differing manner when we change the atmosphere from purely homogeneous to surfactant environment. In the confined medium, we observe the formation of a ground state complex, which is not that much appreciable in the case of homogeneous solvents.

  18. Colloid and surfactant

    International Nuclear Information System (INIS)

    Kuk, Yun Hwan; Lee, Jeong Jung; Cho, Sun Chae; Ryeo, Su Dong

    1995-08-01

    This book consists of two parts about colloid and surfactant. The first parts has explanations colloid and surface science, which deal with creation and properties of colloidal particles, surfactant and micelle colloid, property of surfactant, membranes, absorption of surface science, electrokinetic phenomenon, emulsion, foam and rheology. The second part mentions surfactant on anionic surfactant with five types, amphoteric surface active agent, non-ionic surface active agent and use of surfactant.

  19. Micellar solubilization of poorly water-soluble drugs: effect of surfactant and solubilizate molecular structure.

    Science.gov (United States)

    Vinarov, Zahari; Katev, V; Radeva, D; Tcholakova, S; Denkov, N D

    2018-04-01

    This study aims to clarify the role of surfactant and drug molecular structures on drug solubility in micellar surfactant solutions. (1) Rationale for surfactant selection is provided; (2) the large data set can be used for validation of the drug solubility parameters used in oral absorption models. Equilibrium solubility of two hydrophobic drugs and one model hydrophobic steroid in micellar solutions of 19 surfactants was measured by HPLC. The drug solubilization locus in the micelles was assessed by UV spectrometry. Danazol is solubilized much more efficiently than fenofibrate by ionic surfactants due to ion-dipole interactions between the charged surfactant head groups and the polar steroid backbone. Drug solubilization increases linearly with the increase of hydrophobic chain length for all studied surfactant types. Addition of 1-3 ethylene oxide (EO) units in the head group of dodecyl sulfate surfactants reduces significantly the solubilization of both studied drugs and decreases linearly the solubilization locus polarity of fenofibrate. The locus of fenofibrate solubilization is in the hydrophobic core of nonionic surfactant micelles and in the palisade layer of ionic surfactant micelles. Highest drug solubility can be obtained by using surfactants molecules with long chain length coupled with hydrophilic head group that provides additional drug-surfactant interactions (i.e. ion-dipole) in the micelles.

  20. Determination of sodium bis(2-ethylhexylsulfosuccinate (AOT surfactant with liquid chromatography: Comparative study of evaporative light scattering detector, ultraviolet detector and conductivity detector

    Directory of Open Access Journals (Sweden)

    Ho Ryul Ryu

    2010-03-01

    Full Text Available This work presents comparison of performance of ultraviolet (UV detector, conductivity detector (CD and evaporative light scattering detector (ELSD in terms of quantitative analysis of AOT (sodium bis(2-ethylhexylsulfosuccinate using liquid chromatography. The employed chromatographic condition, including an acetonitrile/water (45:55, v/v isocratic eluent system, is suitable for the three different detectors, and the figures of merits obtained by building up calibration plots are compared. The sensitivities of the detectors are in the order of ELSD ≈ CD >> UV detector. The linear range for quantification of AOT depends on the type of detector: the lower limits are in the order of UV detector (207 ㎍ mL-1 < CD (310 ㎍ mL-1 << ELSD (930 ㎍ mL-1, while the upper limits are 3720 ㎍ mL-1 for all the detectors (the maximum concentration of injected standard solution. The detection limits are 155 ㎍ mL-1 for ELSD, 78 ㎍ mL-1 for UV detector and 13 ㎍ mL-1 for CD, respectively. The figures of merit for each detector could be a guideline in choosing a detector in quantization of AOT. Furthermore, application of the chromatographic method to two commercial products is demonstrated.

  1. Influence of Various Surfactants on Size, Morphology, and Optical Properties of CeO2 Nanostructures via Facile Hydrothermal Route

    Directory of Open Access Journals (Sweden)

    S. Gnanam

    2013-01-01

    Full Text Available Different surfactants such as sodium dodecyl sulfate (SDS, polyethylene glycol (PEG, and cetyltrimethyl ammonium bromide (CTAB, assisted cerium oxide (CeO2 nanoparticles were synthesized by using cerium chloride and potassium hydroxide as the starting materials via facile hydrothermal route. The powder X-ray diffraction (XRD shows that cubic fluorite-type structure of pure CeO2 and the average crystallite sizes were calculated to be ~12–16 nm. Raman spectra of various surfactants assisted CeO2 consist of a single triply degenerated F2g mode characteristic of the fluorite structure. The elongated spherical-like morphology of SDS assisted CeO2 samples was observed from the SEM and TEM studies. Optical absorption spectra showed a blue shift by the capped CeO2 due to the quantum confinement effect. Photoluminescence (PL emission studies shows that there is a change in the intensity of emission peaks by the capping agents, which indicates that the capping layers did result in size changes or increased surface defect.

  2. Status of surfactants as penetration enhancers in transdermal drug delivery

    Directory of Open Access Journals (Sweden)

    Iti Som

    2012-01-01

    Full Text Available Surfactants are found in many existing therapeutic, cosmetic, and agro-chemical preparations. In recent years, surfactants have been employed to enhance the permeation rates of several drugs via transdermal route. The application of transdermal route to a wider range of drugs is limited due to significant barrier to penetration across the skin which is associated with the outermost stratum corneum layer. Surfactants have effects on the permeability characteristics of several biological membranes including skin. They have the potential to solubilize lipids within the stratum corneum. The penetration of the surfactant molecule into the lipid lamellae of the stratum corneum is strongly dependent on the partitioning behavior and solubility of surfactant. Surfactants ranging from hydrophobic agents such as oleic acid to hydrophilic sodium lauryl sulfate have been tested as permeation enhancer to improve drug delivery. This article reviews the status of surfactants as permeation enhancer in transdermal drug delivery of various drugs.

  3. Adsorption of anionic surfactants in limestone medium during oil recovery

    Energy Technology Data Exchange (ETDEWEB)

    Canbolat, Serhat; Bagci, Suat [Middle East Technical Univ., Dept. of Petroleum and Natural Gas Engineering, Ankara (Turkey)

    2004-07-15

    Foam-forming surfactant performance was evaluated by several experimental methods (interfacial tension, foam stability, corefloods) using commercial surfactants. There is considerable interest in the use of foam-forming surfactants for mobility control in water flood. To provide effective mobility control, the injected surfactant must propagate from the injection well toward the production well. One of the important parameters affecting propagation of foam-forming surfactant through the reservoir is the retention of surfactant due to its adsorption on reservoir rock. The determination of the adsorption of foam-forming surfactants in limestone reservoirs is important for the residual oil recovery efficiency. Adsorption measurements, recovery efficiencies, and surfactant and alkaline flooding experiments carried out with the representative of the selected surfactants alkaline solutions, linear alkyl benzene sulphonic acid (LABSA), sodium lauryl ether sulfate (SLES), and NaOH in a limestone medium. These surfactants were selected with respect to their foaming ability. Calibration curves formed by pH measurements were used to determine the correct adsorption amount of the used surfactants and recovery efficiency of these surfactants compared with base waterflooding. The results showed that LABSA adsorbed more than SLES in limestone reservoirs. The recovery efficiency of SLES was higher than the recovery efficiency of LABSA, and they decreased the recovery efficiency with respect to only the water injection case. (Author)

  4. Effects of concentration, temperature and solvent composition on density and apparent molar volume of the binary mixtures of cationic-anionic surfactants in methanol-water mixed solvent media.

    Science.gov (United States)

    Bhattarai, Ajaya; Chatterjee, Sujeet Kumar; Niraula, Tulasi Prasad

    2013-01-01

    The accurate measurements on density of the binary mixtures of cetyltrimethylammonium bromide and sodium dodecyl sulphate in pure water and in methanol(1) + water (2) mixed solvent media containing (0.10, 0.20, and 0.30) volume fractions of methanol at 308.15, 318.15, and 323.15 K are reported. The concentrations are varied from (0.03 to 0.12) mol.l(-1) of sodium dodecyl sulphate in presence of ~ 5.0×10(-4) mol.l(-1) cetyltrimethylammonium bromide. The results showed almost increase in the densities with increasing surfactant mixture concentration, also the densities are found to decrease with increasing temperature over the entire concentration range, investigated in a given mixed solvent medium and these values are found to decrease with increasing methanol content in the solvent composition. The concentration dependence of the apparent molar volumes appear to be negligible over the entire concentration range, investigated in a given mixed solvent medium and the apparent molar volumes increase with increasing temperature and are found to decrease with increasing methanol content in the solvent composition.

  5. [Exogenous surfactant therapy: new synthetic surfactants].

    Science.gov (United States)

    Lacaze-Masmonteil, Th

    2008-06-01

    There are numerous pulmonary conditions in which qualitative or quantitative anomalies of the surfactant system have been demonstrated. In premature newborns with immature lungs, a functional deficit in surfactant is the main physiopathologic mechanism of the neonatal respiratory distress syndrome (RDS). Since the landmark pilot study of Fujiwara, published more than 20 years ago, the efficacy of exogenous surfactant for the treatment of neonatal RDS has been established by numerous controlled studies and meta-analyses. Enlightened by a growing insight into both the structure and function of the different surfactant components, a new generation of synthetic surfactants has been developed. Various complementary approaches have confirmed the fundamental role of the two hydrophobic proteins, SP-B and SP-C, in the surfactant system, thus opening the way to the design of analogues, either by chemical synthesis or expression in a prokaryotic system. An example of these peptide-containing synthetic surfactant preparations, lucinactant (Surfaxin), has been recently tested in comparison to a synthetic surfactant that does not contain protein as well as to animal derived surfactant preparations. Major clinical outcomes between lucinactant and animal-derived surfactant preparations were fund similar in two randomized controlled trials, opening the way to a new generation of synthetic surfactants in the near future.

  6. Simultaneous removal of binary mixture of Brilliant Green and Crystal Violet using derivative spectrophotometric determination, multivariate optimization and adsorption characterization of dyes on surfactant modified nano-γ-alumina.

    Science.gov (United States)

    Zolgharnein, Javad; Bagtash, Maryam; Shariatmanesh, Tahere

    2015-02-25

    The present study deals with the simultaneous removal of Brilliant Green (BG) and Crystal Violet (CV) by surfactant-modified alumina. The utilization of alumina nanoparticles with an anionic surfactant (sodium dodecyl sulfate (SDS)) as a novel and efficient adsorbent is successfully carried out to remove two cationic dyes from aqueous solutions in binary batch systems. A first-order derivative spectrophotometric method is developed for the simultaneous determination of BG and CV in binary solutions. The linear concentration range and limits of detection for the simultaneous determination of BG and CV were found to be: 1-20, 1-15 mg/L, 0.3 and 0.5 mg/L, respectively. The influence of various parameters, such as contact time, initial concentration of dyes and sorbent mass on the dye adsorption is investigated. A response surface methodology achieved through performing the Box-Behnken design is utilized to optimize the removal of dyes by surfactant-modified nanoparticle alumina through a batch adsorption process. The proposed quadratic model resulting from the Box-Behnken design approach fitted very well with the experimental data. The optimal conditions for dye removal were contact time t=50 min, sorbent dose=0.036 g, CBG (Initial BG concentration)=215 mg/L and CCV (Initial CV concentration)=170 mg/L. Furthermore, FT-IR analysis, the isotherms and kinetics of adsorption were also explored. Copyright © 2014 Elsevier B.V. All rights reserved.

  7. Simultaneous removal of binary mixture of Brilliant Green and Crystal Violet using derivative spectrophotometric determination, multivariate optimization and adsorption characterization of dyes on surfactant modified nano-γ-alumina

    Science.gov (United States)

    Zolgharnein, Javad; Bagtash, Maryam; Shariatmanesh, Tahere

    2015-02-01

    The present study deals with the simultaneous removal of Brilliant Green (BG) and Crystal Violet (CV) by surfactant-modified alumina. The utilization of alumina nanoparticles with an anionic surfactant (sodium dodecyl sulfate (SDS)) as a novel and efficient adsorbent is successfully carried out to remove two cationic dyes from aqueous solutions in binary batch systems. A first-order derivative spectrophotometric method is developed for the simultaneous determination of BG and CV in binary solutions. The linear concentration range and limits of detection for the simultaneous determination of BG and CV were found to be: 1-20, 1-15 mg/L, 0.3 and 0.5 mg/L, respectively. The influence of various parameters, such as contact time, initial concentration of dyes and sorbent mass on the dye adsorption is investigated. A response surface methodology achieved through performing the Box-Behnken design is utilized to optimize the removal of dyes by surfactant-modified nanoparticle alumina through a batch adsorption process. The proposed quadratic model resulting from the Box-Behnken design approach fitted very well with the experimental data. The optimal conditions for dye removal were contact time t = 50 min, sorbent dose = 0.036 g, CBG (Initial BG concentration) = 215 mg/L and CCV (Initial CV concentration) = 170 mg/L. Furthermore, FT-IR analysis, the isotherms and kinetics of adsorption were also explored.

  8. Enzymatic Degradation of Dynasan 114 SLN - Effect of Surfactants and Particle Size

    Energy Technology Data Exchange (ETDEWEB)

    Olbrich, Carsten; Kayser, Oliver; Mueller, Rainer Helmut [Free University of Berlin, Department of Pharmaceutics, Biopharmaceutics and Biotechnology (Germany)], E-mail: mpharma@zedat.fu-berlin.de

    2002-04-15

    The degradation velocity of solid lipid nanoparticles (SLN) is - apart from drug diffusion - an important parameter determining drug release in vivo. To assess the effect of stabilizers systematically, Dynasan 114 SLN were produced with ionic surfactants (e.g. cholic acid sodium salt (NaCh), sodium dodecyl sulfate (SDS), cetylpyridiniumchloride (CPC)) and steric stabilizers (Tween 80, Poloxamer 188, 407 and Poloxamine 908) including a mixture of cholic acid sodium salt and Poloxamer 407. In addition, the size effects were investigated. The degradation velocity was measured using an in vitro lipase assay. SLN stabilized with lecithin and NaCh showed the fastest, Tween 80 the intermediate and the high molecular weight Poloxamer 407 the slowest degradation. Size effects were less pronounced for fast degrading particles (e.g. those stabilized with NaCh). No difference in the size range of 180-300-nm was observed, but a distinctly slower degradation of 800-nm SLN could be detected. For slowly degrading particles, more pronounced size effects were found. Size effects are more difficult to assess when the PCS diameters are similar, but small fractions of micrometer particles are present, besides the nanometer bulk population. The measured FFA formation is then a superposition of particles degrading at different speeds due to differences in the shape of the size distribution. Admixing of Poloxamer to NaCh had no delaying effect on the degradation of the Dynasan 114 SLN, indicating an influence of the nature of the lipid matrix that is affecting the stabilizers affinity to and anchoring onto the SLN surface.

  9. Determination of melamine in soil samples using surfactant-enhanced hollow fiber liquid phase microextraction followed by HPLC–UV using experimental design

    Directory of Open Access Journals (Sweden)

    Ali Sarafraz Yazdi

    2015-11-01

    Full Text Available Surfactant-enhanced hollow fiber liquid phase (SE-HF-LPME microextraction was applied for the extraction of melamine in conjunction with high performance liquid chromatography with UV detection (HPLC–UV. Sodium dodecyl sulfate (SDS was added firstly to the sample solution at pH 1.9 to form hydrophobic ion-pair with protonated melamine. Then the protonated melamine–dodecyl sulfate ion-pair (Mel–DS was extracted from aqueous phase into organic phase immobilized in the pores and lumen of the hollow fiber. After extraction, the analyte-enriched 1-octanol was withdrawn into the syringe and injected into the HPLC. Preliminary, one variable at a time method was applied to select the type of extraction solvent. Then, in screening step, the other variables that may affect the extraction efficiency of the analyte were studied using a fractional factorial design. In the next step, a central composite design was applied for optimization of the significant factors having positive effects on extraction efficiency. The optimum operational conditions included: sample volume, 5 mL; surfactant concentration, 1.5 mM; pH 1.9; stirring rate, 1500 rpm and extraction time, 60 min. Using the optimum conditions, the method was analytically evaluated. The detection limit, relative standard deviation and linear range were 0.005 μg mL−1, 4.0% (3 μg mL−1, n = 5 and 0.01–8 μg mL−1, respectively. The performance of the procedure in extraction of melamine from the soil samples was good according to its relative recoveries in different spiking levels (95–109%.

  10. Influence of metacide - surfactant complexes on agricultural crops

    Directory of Open Access Journals (Sweden)

    Orynkul Esimova

    2014-12-01

    Full Text Available The complexes based on surfactants and polyhexamethyleneguanidine hydrochloride (metacide are important for agriculture. This paper considers compositions of known bactericidal metacide with different surfactants: anionic surfactant sodium dodecylsulphate (DDSNa and nonionic surfactant Tween 80 (monooleate of oxyethylenated anhydrosorbitols. The effect of individual components and associates of metacide and surfactants on productivity and infection of cereals was studied. According to the study, the highest productivity and infection rate were shown by the associate of metacide and Tween-80. At concentration of Tween-80 in aqueous solution equal to 0.001% in combination with metacide, efficiency was 98% at 0% infection. The surface tension and the wetting of metacide, DDSNa, Tween-80, and associates of metacide with surfactants were studied. In comparison with individual components, metacide-DDSNa and metacide-Tween-80 associates have higher surface activity.

  11. Small angle neutron scattering studies of mixed micelles of sodium

    Indian Academy of Sciences (India)

    The aqueous solutions of sodium cumene sulphonate (NaCS) and its mixtures with each of cetyl trimethylammonium bromide (CTAB) and sodium dodecyl sulphate (SDS) are characterized by small angle neutron scattering (SANS). NaCS when added to CTAB solution leads to the formation of long rod-shaped micelles with ...

  12. Adsorption of model perfumes at the air-solution interface by coadsorption with an anionic surfactant.

    Science.gov (United States)

    Bradbury, Robert; Penfold, Jeffrey; Thomas, Robert K; Tucker, Ian M; Petkov, Jordan T; Jones, Craig

    2013-03-12

    The adsorption of the model perfumes phenyl ethanol, PE, and linalool, LL, at the air-solution interface by coadsorption with the anionic surfactant sodium dodecyl 6-benezene sulfonate, LAS-6, has been studied primarily by neutron reflectivity, NR. The variation in the mixed surface adsorption with solution composition is highly nonideal, and the more hydrophobic LL is more surface active. At a LAS-6 concentration of 0.5 mM the adsorption of PE and LL is broadly similar but with the LL systematically more surface active, and at 2 mM the LL completes more effectively for the surface than the PE. The variation in surface composition with solution composition and concentration reflect the greater hydrophobicity and hence surface activity of LL, and the greater solubility of PE in aqueous solution. Changing the geometry of the LAS isomer, from the symmetrical LAS-6 geometry to the more asymmetrical LAS-4, results in the LL competing more effectively for the surface due to changes in the packing constraints associated with the hydrophobic region. The results provide insights into the factors that affect coadsorption that can be more broadly applied to the surface delivery of a wide range of molecules other than perfumes.

  13. Effects of surfactants on the formation of gelatin nanofibres for controlled release of curcumin.

    Science.gov (United States)

    Deng, Lingli; Kang, Xuefan; Liu, Yuyu; Feng, Fengqin; Zhang, Hui

    2017-09-15

    This work studied the effects of non-ionic Tween 80, anionic sodium dodecyl sulfonate (SDS) and cationic cetyltrimethyl ammonium bromide (CTAB) surfactants on the morphology of electrospun gelatin nanofibres, and on the release behaviour, antioxidant activity and antimicrobial activity of encapsulated curcumin. Scanning electron micrographs showed that addition of SDS significantly increased the nanofibre diameter. Fourier transform infrared and differential scanning calorimetry analysis indicated that gelatin and SDS intimately interacted via electrostatic and hydrophobic interactions. However, these interactions inhibited the release of curcumin from the nanofibres with SDS, while CTAB and Tween 80 both facilitated the release. SDS and Tween 80 showed protective effects on curcumin from the attack of 2,2-diphenyl-1-picryl-hydrazyl-hydrate (DPPH) radicals, and the increased release of curcumin from nanofibres with CTAB or Tween 80 resulted in a higher reducing power. The antimicrobial activity results suggested that the curcumin encapsulated gelatin nanofibres with CTAB exhibited effective inhibition against Staphylococcus aureus. Copyright © 2017 Elsevier Ltd. All rights reserved.

  14. Anionic Surfactant Removal Using Electrochemical Process: Effect of Electrode Materials and Energy Consumption

    Directory of Open Access Journals (Sweden)

    Batoul Mohebrad

    2018-03-01

    Full Text Available The aim of this study was the investigation of electrochemical process for sodium dodecyl sulfate (SDS removal from aqueous solutions using different electrode materials. The influence of operating parameters such as current density, solution initial pH, surfactant concentrations, retention time, supporting electrolyte concentrations, electrode materials (aluminum, titanium, galvanized steel, stainless steel and electrical energy consumption were evaluated. The obtained results indicated that the stainless steel electrode was more efficient than other electrodes. Maximum SDS removal was obtained 94.98% at the optimum condition of initial pH 7.0, 60 min retention time, 3.125 mA/cm2 current density, 100 mg/L initial SDS concentration and 0.2 g/L NaCl concentration. The electrical energy consumption of stainless steel, aluminum, titanium and galvanized steel was achieved 4, 3.68, 12 and 4.48 KWh/m3, respectively. It was found that the electrochemical reaction using stainless steel plate electrodes was efficient in SDS removal from aquatic environments.

  15. Aggregation study in mixture surfactant system TX-100+SDS in heavy water solutions by SANS method

    Science.gov (United States)

    Rajewska, A.; Islamov, A. Kh.; Bakeeva, R. F.

    2018-03-01

    The mixing of amphiphiles in water may lead to the formation of mixed micelles which often present new properties with respect to the pure component solutions [1,2]. The mixture system of classic surfactants SDS (sodium dodecyl sulfate)+TX-100(p-(1,1,3,3- tetramethyl) poly(oxyethylene) (anionic + non-ionic) in heavy water solutions was investigated at temperatures 30°, 50°, 70°C for compositions 1:1, 2:1, 3:1 by the small-angle neutron scattering(SANS) method on spectrometer (‘YuMO’) at the IBR-2 pulsed neutron source at FLNP, JINR in Dubna (Russia). Measurements have covered Q range from 8x10-3 to 0.4 Å-1. From the measured dependence of the scattered intensity on the scattering angle, we derived the size, shape of micelles, aggregation number at various compositions and temperatures. The size of mixed micelle is a weak function of the mixing ratio between the two components.

  16. Polymer-surfactant complexes for microencapsulation of vitamin E and its release.

    Science.gov (United States)

    Sharipova, A A; Aidarova, S B; Grigoriev, D; Mutalieva, B; Madibekova, G; Tleuova, A; Miller, R

    2016-01-01

    Microencapsulation of vitamin E directly from oil-in-water (o/w) emulsions was carried out by means of a novel practically relevant approach. For the first time, a preformed polyelectrolyte-surfactant complex (sodium polystyrene sulfonate/dodecyl trimethyl ammonium bromide) was simultaneously used as an electrosteric emulsion stabilizer and as a charged precursor for the following build up of microcapsules. Subsequently, a layer-by-layer technique was applied to emulsions leading to the formation of core-shell microcapsules with oily cores and polyelectrolyte shells. The effect of the complexes on the process of emulsion formation and on the stability and characteristics of the resulting emulsions was investigated by measurements of dynamic and equilibrium interfacial tension, size distribution (DLS) and interfacial charge (zeta-potential). The resulting microcapsules were characterized by confocal laser scanning microscopy (CLSM), Cryo-SEM, size distribution and zeta-potential measurements on each stage of the shell assembly. The release kinetics of vitamin E was monitored during the consecutive steps of the encapsulation procedure using UV-vis spectroscopy and showed the progressive enhancement of sustainability. The developed approach may be promising for the practical use in the cosmetic and food industry. Copyright © 2015 Elsevier B.V. All rights reserved.

  17. Investigation of electrokinetic and electrorheological properties of polyindole prepared in the presence of a surfactant

    Energy Technology Data Exchange (ETDEWEB)

    Unal, H. Ibrahim, E-mail: hiunal@gazi.edu.tr [Gazi University, Chemistry Department, Smart Materials Research Lab., Ankara (Turkey); Sahan, Bekir; Erol, Ozlem [Gazi University, Chemistry Department, Smart Materials Research Lab., Ankara (Turkey)

    2012-05-15

    Highlights: Black-Right-Pointing-Pointer Aggregated morphology was determined for PIN, spherical and porous hollows and everniae form morphologies were recorded for SPIN. Black-Right-Pointing-Pointer The PIN/SO and SPIN/SO systems showed almost similar electrokinetic attitudes and a typical shear thinning non-Newtonian viscoelastic behavior, vibration damping capability at elevated frequencies, and enhanced storage moduli with increasing temperature. Black-Right-Pointing-Pointer Non-linear recoverable viscoelastic manner was revealed from the creep-recovery experiments under external electric field. - Abstract: In this study, synthesis of polyindole (PIN) was carried out without and with the presence of a sodium dodecyl sulfate (SDS) surfactant (SPIN), using FeCl{sub 3} as an oxidizing agent. The synthesized materials were subjected to various characterizations techniques namely: particle size, magnetic susceptibility, elemental analysis, density, conductivity, dielectric constant, FTIR, {sup 1}H NMR, TGA, XRD, and SEM. Characterization results revealed the successful preparation of the homopolymers of PIN and SPIN. Zeta ({zeta})-potentials of the samples were measured in aqueous and non-aqueous (silicone oil, SO) media. Electrokinetic properties of PIN and SPIN in aqueous media were determined by {zeta}-potential measurements in the presence of various electrolytes (NaCl, BaCl{sub 2}, AlCl{sub 3}, Na{sub 2}SO{sub 4}) and surfactants (cetyltrimethyl ammonium bromide, SDS, and Triton X-100). Besides, the effect of pH onto {zeta}-potentials of the materials was also examined. The suspensions prepared in SO were subjected to external electric field strength and their electrorheological (ER) properties were investigated. Then the effects of shear rate, frequency, and temperature onto ER activities of the suspensions were examined. Further, creep and creep-recovery tests were applied to the PIN/SO and SPIN/SO suspension systems and reversible non-linear viscoelastic

  18. Surfactant Effect in Polypyrrole and Polypyrrole with Multi Wall Carbon Nanotube Counter Electrodes: Improved Power Conversion Efficiency of Dye-Sensitized Solar Cell.

    Science.gov (United States)

    Thuy, Chau Thi Thanh; Park, Ji Young; Lee, Seung Woo; Suresh, Thogiti; Kim, Jae Hong

    2016-05-01

    In our present study, polypyrrole-1 (PPy1), polypyrrole-2 (PPy2), and polypyrrole-2/multi wall carbon nanotube composite film (PPy2/MWCNT) were proposed as counter electrodes (CEs) in dye-sensitized solar cells (DSSCs) to replace the precious Pt CE. These films were fabricated on fluorine-doped tin oxide substrates by using a facile electrochemical polymerization route, and served as CEs in DSSCs. It is shown that the introduction of anionic surfactant, sodium dodecyl sulfate (SDS), enhanced the catalytic activity, thus leading to an improvement in the performance of PPy2. Further, introduction of MWCNT resulted in increase in conversion efficiency of DSSCs with PPy2/MWCNT composite film. The Tafel and electrochemical impedance analysis revealed that the PPy2 and PPy2/MWCNT CEs prepared with anionic surfactant possessed more catalytic activity and lower charge transfer resistance in comparison with PPy1 -based CE. This resulted in a better conversion efficiency of 5.88% for PPy2/MWCNT-based DSSC under 1 sun condition, reaching 86% of the DSSC based on reference Pt counter electrode (6.86%). These results indicate that the composite film with high catalytic properties for I3- reduction can potentially be used as the CE in a high-performance DSSC.

  19. Br2 production from the heterogeneous reaction of gas-phase OH with aqueous salt solutions: Impacts of acidity, halide concentration, and organic surfactants.

    Science.gov (United States)

    Frinak, Elizabeth K; Abbatt, Jonathan P D

    2006-09-07

    This study reports the first laboratory measurement of gas-phase Br2 production from the reaction between gas-phase hydroxyl radicals and aqueous salt solutions. Experiments were conducted at 269 K in a rotating wetted-wall flow tube coupled to a chemical-ionization mass spectrometer for analysis of gas-phase components. From both pure NaBr solutions and mixed NaCl/NaBr solutions, the amount of Br2 released was found to increase with increasing acidity, whereas it was found to vary little with increasing concentration of bromide ions in the sample. For mixed NaCl/NaBr solutions, Br2 was formed preferentially over Cl2 unless the Br- levels in the solution were significantly depleted by OH oxidation, at which point Cl2 formation was observed. Presence of a surfactant in solution, sodium dodecyl sulfate, significantly suppressed the formation of Br2; this is the first indication that an organic surfactant can affect the rate of interfacial mass transfer of OH to an aqueous surface. The OH-mediated oxidation of bromide may serve as a source of active bromine in the troposphere and contribute to the subsequent destruction of ozone that proceeds in marine-influenced regions of the troposphere.

  20. Effect of surfactant concentration in the electrolyte on the tribological properties of nickel-tungsten carbide composite coatings produced by pulse electro co-deposition

    Science.gov (United States)

    Kartal, Muhammet; Uysal, Mehmet; Gul, Harun; Alp, Ahmet; Akbulut, Hatem

    2015-11-01

    A nickel plating bath containing WC particles was used to obtain hard and wear-resistant particle reinforced Ni/WC MMCs on steel surfaces for anti-wear applications. Copper substrates were used for electro co-deposition of Ni matrix/WC with the particle size of <1 μm tungsten carbide reinforcements. The influence of surfactant (sodium dodecyl sulfate, SDS) concentration on particle distribution, microhardness and wear resistance of composite coatings has been studied. The nickel films were characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The effects of the surfactant on the zeta potential, co-deposition and distribution of WC particles in the nickel matrix, as well as the tribological properties of composite coatings were also investigated. The tribological behaviors of the electrodeposited WC composite coatings sliding against M50 steel ball (Ø 10 mm) were examined on a CSM Instrument. All friction and wear tests were performed without lubrication at room temperature and in the ambient air (relative humidity 55-65%).

  1. Effects of Different Surfactants on Structural, Tribological and Electrical Properties of Pulsed Electro-Codeposited Cu-ZrO2 Composite Coatings

    Science.gov (United States)

    Maharana, H. S.; Basu, A.

    2018-03-01

    Cu-ZrO2 composite coating was synthesized by pulse electrodeposition from an acidic sulfate electrolyte dispersed with nano-sized ZrO2 particles. Effects of different surfactants in different amounts on the codeposition and distribution of ZrO2 particles in the copper matrix, surface-mechanical (hardness and wear) and electrical (conductivity) properties of developed composite coatings have been thoroughly investigated. Sodium dodecyl sulfate (SDS), poly acrylic acid (PAA) and glucose have been added in the electrolyte in different concentrations as anionic, polymeric and nonionic surfactants. Obtained experimental results confirmed that addition of SDS up to 1 g/L improves the amount of codeposited ZrO2 particles in the copper matrix and surface-mechanical properties of the nanocomposite coatings. But, in case of PAA- and glucose-assisted coatings, highest amount of ZrO2 codeposition was observed in 0.5 g/L PAA and 20 g/L glucose-assisted coatings, which in turn affected the mechanical properties. Surface-mechanical properties were found to be affected by coating matrix morphology and crystallographic orientation along with embedded ZrO2 particle content. Electrical conductivity of all the deposits not only depends upon the codeposition of ZrO2 particles in the matrix but also on the microstructure and crystallographic orientation.

  2. Studies on Anionic Surfactant Structure in the Aggregation with (Hydroxypropylcellulose

    Directory of Open Access Journals (Sweden)

    Ricardo M. de Martins

    2002-01-01

    Full Text Available Fluorescence probing, viscosity and light scattering measurements have been combined to study the aggregation of different anionic surfactants mainly in dilute solutions (0.5% w/v of (hydroxypropylcellulose (HPC MW 173,000, in moderate ionic strength (NaCl 0.1 mol.L-1. The set of surfactants includes natural cholesterol derivatives, sodium cholate (CS and sodium deoxycholate (DC, and the alkylsulphate, sodium dodecylsulphate (SDS. At 298 K the critical surfactant concentration related to aggregate/HPC formation (C1 decreases for SDS and DC whereas it increases slightly for CS. At 312 K the C1 values for CS and DC are slightly shifted toward higher values whereas it is not changed for SDS. All surfactant/HPC systems increase C1 values as the HPC concentration increases to 1.2%. Above C1 the viscosity increases for all surfactant/HPC systems but it is sharper in the increasing order CS, DC and SDS. The hydrodynamic behavior indicates that CS induces higher diffusion to HPC than SDS and DC. The aggregation in the surfactant/HPC systems is analyzed through the feature of surfactant/aggregate structure (size, charge density, etc.

  3. Gemini (dimeric) Surfactants

    Indian Academy of Sciences (India)

    Gemini, surfactants, micelle. Figure 1. Schematic repre- sentation of the gemini sur- factant structure. B S Sekhon. A gemini surfactant (GS) consists of two conventional surfactant molecules chemically bonded together by a spacer. The two terminal hydrocarbon tails can be short or long; the two polar head groups can be ...

  4. Surfactant Based Enhanced Oil Recovery and Foam Mobility Control

    Energy Technology Data Exchange (ETDEWEB)

    George J. Hirasaki; Clarence A. Miller

    2006-09-09

    Surfactant flooding has the potential to significantly increase recovery over that of conventional waterflooding. The availability of a large number of surfactant structures makes it possible to conduct a systematic study of the relation between surfactant structure and its efficacy for oil recovery. A mixture of two surfactants was found to be particularly effective for application in carbonate formations at low temperature. The mixture is single phase for higher salinity or calcium concentrations than that for either surfactant used alone. This makes it possible to inject the surfactant slug with polymer close to optimal conditions and yet be single phase. A formulation has been designed for a particular field application. It uses partially hydrolyzed polyacrylamide for mobility control. The addition of an alkali such as sodium carbonate makes possible in situ generation of naphthenic soap and significant reduction of synthetic surfactant adsorption. The design of the process to maximize the region of ultra-low IFT takes advantage of the observation that the ratio of soap to synthetic surfactant is a parameter in the conditions for optimal salinity. Even for a fixed ratio of soap to surfactant, the range of salinity for low IFT was wider than that reported for surfactant systems in the literature. Low temperature, forced displacement experiments in dolomite and silica sandpacks demonstrate that greater than 95% recovery of the waterflood remaining oil is possible with 0.2% surfactant concentration, 0.5 PV surfactant slug, with no alcohol. Compositional simulation of the displacement process demonstrates the role of soap/surfactant ratio on passage of the profile through the ultralow IFT region, the importance of a wide salinity range of low IFT, and the importance of the viscosity of the surfactant slug. Mobility control is essential for surfactant EOR. Foam is evaluated to improve the sweep efficiency of surfactant injected into fractured reservoirs as well as a

  5. Determination of the anionic surfactant di(ethylhexyl) sodium sulfosuccinate in water samples collected from Gulf of Mexico coastal waters before and after landfall of oil from the Deepwater Horizon oil spill, May to October, 2010

    Science.gov (United States)

    Gray, James L.; Kanagy, Leslie K.; Furlong, Edward T.; McCoy, Jeff W.; Kanagy, Chris J.

    2011-01-01

    On April 22, 2010, the explosion on and subsequent sinking of the Deepwater Horizon oil drilling platform resulted in the release of crude oil into the Gulf of Mexico. At least 4.4 million barrels had been released into the Gulf of Mexico through July 15, 2010, 10 to 29 percent of which was chemically dispersed, primarily using two dispersant formulations. Initially, the dispersant Corexit 9527 was used, and when existing stocks of that formulation were exhausted, Corexit 9500 was used. Over 1.8 million gallons of the two dispersants were applied in the first 3 months after the spill. This report presents the development of an analytical method to analyze one of the primary surfactant components of both Corexit formulations, di(ethylhexyl) sodium sulfosuccinate (DOSS), the preliminary results, and the associated quality assurance/quality control (QA/QC) from samples collected from various points on the Gulf Coast between Texas and Florida. Seventy water samples and 8 field QC samples were collected before the predicted landfall of oil (pre-landfall) on the Gulf Coast, and 51 water samples and 10 field QC samples after the oil made landfall (post-landfall). Samples were collected in Teflon(Registered) bottles and stored at -20(degrees)C until analysis. Extraction of whole-water samples used sorption onto a polytetrafluoroethylene (PTFE) filter to isolate DOSS, with subsequent 50 percent methanol/water elution of the combined dissolved and particulate DOSS fractions. High-performance liquid chromatography/tandem mass spectrometry (LC/MS/MS) was used to identify and quantify DOSS by the isotope dilution method, using a custom-synthesized 13C4-DOSS labeled standard. Because of the ubiquitous presence of DOSS in laboratory reagent water, a chromatographic column was installed in the LC/MS/MS between the system pumps and the sample injector that separated this ambient background DOSS contamination from the sample DOSS, minimizing one source of blank contamination

  6. Mixed Surfactant Template Method for Preparation of Nanometer Selenium

    Directory of Open Access Journals (Sweden)

    Zhi-Lin Li

    2009-01-01

    Full Text Available Selenium nanoparticles have been synthesized in an aqueous solution by using sodium dodecyl sulfate and polyvinyl alcohol as a soft template. The factors on synthesis, such as reaction time, concentration of reactants and ultrasonic irradiation were studied. The uniform stable selenium nanospheres were obstained in the conditions of 1.0 (mass fraction sodium dodecyl sulfate, 1.0 (mass fraction polyvinyl alcohol, n(Vc:n(H2SeO3=7:1 and 7 minutes after the initiation of the reaction at room temperature. The average particle size of selenium is about 30 nm. The product was characterized by UV and TEM. Finally the applications of the red element nanometer selenium in anti-older cosmetics are presented.

  7. Energetic and binding properties of DNA upon interaction with dodecyl trimethylammonium bromide.

    Science.gov (United States)

    Bathaie, S Z; Moosavi-Movahedi, A A; Saboury, A A

    1999-02-15

    The interaction of dodecyl trimethylammonium bromide (DTAB), a cationic surfactant, with calf thymus DNA has been studied by various methods, including potentiometric technique using DTAB-selective plastic membrane electrode at 27 and 37 degreesC, isothermal titration microcalorimetry and UV spectrophotometry at 27 degreesC using 0.05 M Tris buffer and 0.01 M NaCl at pH 7.4. The free energy is calculated from binding isotherms on the basis of Wyman binding potential theory and the enthalpy of binding according to van't Hoff relation. The enthalpy of unfolding has been determined by subtraction of the enthalpy of binding from the microcalorimetric enthalpy. The results show that, after the interaction of first DTAB molecule to DNA (base molarity) through the electrostatic interaction, the second DTAB molecule also binds to DNA through electrostatic interaction. At this stage, the predom-inant DNA conformational change occurs. Afterwards up to 20 DTAB molecules, below the critical micelle concentration of DTAB, bind through hydrophobic interactions.

  8. Surfactant use with nitrate-based bioremediation

    International Nuclear Information System (INIS)

    Wilson, B.H.; Hutchins, S.R.; West, C.C.

    1995-01-01

    This study presents results of an initial survey on the effect of six surfactants on the biodegradation of petroleum hydrocarbons in bioremediation applications using nitrate as the electron acceptor. Aquifer material from Park City, Kansas, was used for the study. The three atomic surfactants chosen were Steol CS-330, Dowfax 8390 and sodium dodecylbenzene sulfonate (SDBS); the three nonionic surfactants were T-MAZ-60, Triton X-100, and Igepal CO-660. Both Steol CS-330 and T-MAZ-60 biodegraded under denitrifying conditions. The Steol inhibited biodegradation of benzene, toluene, ethylbenzene, xylenes, and trimethylbenzenes (BTEXTMB). Only toluene was rapidly degraded in the presence of T-MAZ-60. Biodegradation of all compounds, including toluene, appears to be inhibited by Dowfax 8390 and SDBS. No biodegradation of Dowfax 8390 or SDBS was observed. SDBS inhibited denitrification, but Dowfax 8390 did not. For the microcosms containing Triton X-100 or Igepal CO-660, removal of toluene, ethylbenzene, m-xylene, 1,3,5-TMB, and 1,2,4-TMB were similar to their removals in the no-surfactant treatment. These two surfactants did not biodegrade, did not inhibit biodegradation of the alkylbenzenes, and did not inhibit denitrification. Further studies are continuing with aquifer material from Eglin Air Force Base

  9. Surfactant Enhanced Microbial Degradation of JP-8 Contaminated Soil

    Science.gov (United States)

    1996-12-01

    Halogenated Aromatics PCBs Branched Alkanes In the deeper areas of the unsaturated zone there are 106 to 107 organisms per gram of dry soil (Mitchell...semialdehyde ( OH Smuconate- lactonizing 2-hydroxymuconic enzyme Isemialdehyde hydrolase (2 OOH CH2 OOH muconolactone 0 0 2-oxopent-4-enoate Further...and sodium dodecyl sulfate (SDS). Both unsaturated and saturated conditions were investigated in this study. The tests revealed that all of the

  10. Detection of phthalates migration from disposable tablewares to drinking water using hexafluoroisopropanol-induced catanionic surfactant coacervate extraction

    Directory of Open Access Journals (Sweden)

    Cao Li

    2016-10-01

    Full Text Available Hexafluoroisopropanol (HFIP-induced sodium dodecyl sulfate/dodecyltrimethylammonium bromide (SDS/DTAB catanionic surfactant coacervate extraction method coupled with high performance liquid chromatography (HPLC was used to detect the migration of phthalates from disposable tablewares to drinking water. The concentration factors are larger than 82 and extraction recoveries over 53% for water samples spiked with 100 or 200 ng/mL phthalates. Limit of detection is in the range of 1.0–2.6 ng/mL. Good linearity with correlation coefficients larger than 0.9985 is obtained in the concentration of 20–1500 or 40–3000 ng/mL. Relative recoveries are from 82.4% to 123.6% for water samples spiked with 30/60, 250/500, and 1500/3000 ng/mL phthalates, respectively. Relative standard deviations (RSDs are 0.4%–7.4% for intraday precision (n=5 and 0.6%–7.8% for interday precision (n=3. Four of studied phthalates are found in the drinking water samples prepared from four kinds of tablewares.

  11. Preparation and Application of Immobilized Surfactant-Modified PANi-CNT/TiO2 under Visible-Light Irradiation

    Directory of Open Access Journals (Sweden)

    Ching Yuan

    2017-07-01

    Full Text Available Hydrothermally and sol-gel-synthesized immobilized surfactant-modified polyaniline-carbon nanotubes/TiO2 (PANi-CNT/TiO2 photocatalysts were prepared and their application in the degradation of diethyl phthalate (DEP under visible light at 410 nm was investigated in this sturdy. To improve the dispersion of nanoparticles and the transfer of electrons, the TiO2 surface was modified with both sodium dodecyl sulfate (SDS and functionalized carbon nanotubes (CNT-COOH and CNT-COCl. With the addition of PANi, which was increased from 1%–5%, the adsorption edge of the prepared photocatalysts shifted to 442 nm. The SDS linked the PANi polymers to achieve a thickness of coating of the film of up to 314–400 nm and 1301–1600 nm for sol-gel hydrolysis and hydrothermally-synthesized photocatalysts, respectively. An appropriate film thickness would extend the transfer path of the electrons and inhibit the recombination of the electrons and the electron-holes. The photo-degradation performance of DEP by the hydrothermally-synthesized photocatalysts was better than those by sol-gel hydrolysis. The results revealed that the hydroxyl radicals were the key oxidant in the degradation of DEP using hydrothermally-synthesized PANi-CNT/TiO2 photocatalysts. The morphology and functional groups of the raw materials of photocatalysts were characterized and a comparison of photocatalytic activity with other TiO2-based photocatalysts was also provided.

  12. Structural Modification and Self-Assembly of Nanoscale Magnetite Synthesised in the Presence of an Anionic Surfactant

    Science.gov (United States)

    Malik, S.; Hewitt, I. J.; Powell, A. K.

    2014-07-01

    The earliest reported medical use of magnetite powder for internal applications was in the 10th century A.D. by the Persian physician and philosopher Avicenna of Bokhara [1,2]. Today magnetic nanoparticles are used for magnetic resonance imaging (MRI) and are potential colloidal mediators for cancer magnetic hyperthermia [3]. Twenty years ago magnetite (Fe3O4) was found to be present in the human brain [4] and more recently it has been reported that nanoscale biogenic magnetite (origin and formation uncertain) is associated with neurodegenerative diseases such as Parkinson's, Huntington's and Alzheimer's [5]. Here we show that the synthesis of magnetite in the presence of the surfactant sodium dodecyl sulphate (SDS) gives rise to a variety of nanoscale morphologies, some of which look remarkably similar to magnetite found in organisms, suggesting that similar processes may be involved. Furthermore, these 1D materials with diameters of quantum confined size are of interest in the areas of biosensors [6] and biomedical imaging [7].

  13. Structural Modification and Self-Assembly of Nanoscale Magnetite Synthesised in the Presence of an Anionic Surfactant

    Directory of Open Access Journals (Sweden)

    Malik S.

    2014-07-01

    Full Text Available The earliest reported medical use of magnetite powder for internal applications was in the 10th century A.D. by the Persian physician and philosopher Avicenna of Bokhara [1,2]. Today magnetic nanoparticles are used for magnetic resonance imaging (MRI and are potential colloidal mediators for cancer magnetic hyperthermia [3]. Twenty years ago magnetite (Fe3O4 was found to be present in the human brain [4] and more recently it has been reported that nanoscale biogenic magnetite (origin and formation uncertain is associated with neurodegenerative diseases such as Parkinson’s, Huntington’s and Alzheimer’s [5]. Here we show that the synthesis of magnetite in the presence of the surfactant sodium dodecyl sulphate (SDS gives rise to a variety of nanoscale morphologies, some of which look remarkably similar to magnetite found in organisms, suggesting that similar processes may be involved. Furthermore, these 1D materials with diameters of quantum confined size are of interest in the areas of biosensors [6] and biomedical imaging [7].

  14. Investigation of Surfactant Type, Dosage and Ultrasonication Temperature Control on Dispersity of Metal-Coated Multi-Walled Carbon Nanotubes.

    Science.gov (United States)

    Liang, Xiaoning; Li, Wei

    2016-04-01

    We studied the dispersity of multi-walled carbon nanotubes (MWNTs) combined with different metal- lic particles (Ni and Fe). An ultrasonic-assisted water-bath dispersion process was used to dis- perse the metal-coated MWNTs in different solutions and the dispersity was measured using an ultraviolet-visible spectrophotometer. The dispersity and morphology of the MWNTs were characterized using field-emission scanning electron microscopy (FE-SEM) together with digital image processing technology. Effects of dispersant type (sodium dodecyl benzene sulfonate (SDBS), oleic acid, and polymer (TNEDIS)) and surfactant dosage on the dispersity of the metal-coated MWNTs were investigated under controlled and uncontrolled temperatures and results were compared with those from the untreated MWNTs. The results showed that the negative effects of temperature on the ultrasonic dispersion process could be eliminated through a temperature-controlled system. Moreover, the TNEDIS, SDBS, and oleic acid were arranged in the descending order of the dispersion effect degree. The untreated MWNTs, Ni-coated MWNTs, and Fe-coated MWNTs were arranged in the descending degree of dispersity order. Since the metal coating makes the MWNTs harder and more fragile, the metal-coated MWNTs are more likely to fracture during the ultrasonic dispersion process.

  15. Surfactants in tribology

    CERN Document Server

    Biresaw, Girma

    2014-01-01

    Surface science and tribology play very critical roles in many industries. Manufacture and use of almost all consumer and industrial products rely on the application of advanced surface and tribological knowledge. The fourth in a series, Surfactants in Tribology, Volume 4 provides an update on research and development activities connecting surfactants and tribological phenomena. Written by renowned subject matter experts, the book demonstrates how improved design of surfactants can be harnessed to control tribological phenomena. Profusely illustrated and copiously referenced, the chapters also

  16. Studies on interfacial tension and contact angle of synthesized surfactant and polymeric from castor oil for enhanced oil recovery

    Science.gov (United States)

    Babu, Keshak; Pal, Nilanjan; Bera, Achinta; Saxena, V. K.; Mandal, Ajay

    2015-10-01

    New synthesized polymeric surfactants have immensely attracted the researchers for further development of chemical enhanced oil recovery method particularly in surfactant flooding. Contact angle and interfacial tension measurement tests are the effective ways to identify proper chemicals/surfactants for enhanced oil recovery by chemical/surfactant flooding. In the present study a new polymeric surfactant was synthesized from pre-synthesized sodium methyl ester sulfonate (surfactant) and acrylamide for application in chemical enhanced oil recovery. The synthesized surfactant and polymeric surfactant were used to measure interfacial tension between their aqueous phase and crude oil phase to investigate the efficiency of the surfactants in reduction of interfacial tension. The synthesized polymeric surfactant has also ability to control the mobility because of its viscous nature in aqueous solution. Contact angles of solid-crude oil-surfactant interface were also measured to study the effect of the synthesized surfactant and polymeric surfactant on wettability alteration mechanism. Synergistic effect was studied by using NaCl and synthesized surfactants on interfacial tension. Dynamic interfacial tensions of the surfactant and polymeric surfactant solutions with crude oil were measured at different NaCl concentrations. Interfacial tension was found to be lowered up to 10-2 to 10-3 mN/m which is effective for oil recovery. Measurement of contact angle indicates the wettability change of the quartz surface. Comparative studies on efficiencies of synthesized sodium methyl ester sulfonate surfactant and polymeric surfactant were also carried out with respect to interfacial tension reduction and contact angle change.

  17. Genetics Home Reference: surfactant dysfunction

    Science.gov (United States)

    ... Email Facebook Twitter Home Health Conditions Surfactant dysfunction Surfactant dysfunction Printable PDF Open All Close All Enable Javascript to view the expand/collapse boxes. Description Surfactant dysfunction is a lung disorder that causes breathing ...

  18. An experimental investigation of the effects of surfactants on the severity of vapor explosions

    International Nuclear Information System (INIS)

    Kowal, M.G.; Dowling, M.F.; Abdel-Khalik, S.I.

    1993-01-01

    Dilute aqueous solutions of two surface active agents (surfactants) were tested for their ability to suppress spontaneous steam explosions in molten tin/water systems. At 800C, 12 g of tin were dropped into aqueous solutions of a nonionic surfactant (nonylphenol polyethylene glycol ether) and an ionic surfactant (dodecylbenzene sulfonate sodium salt) with concentrations of 5, 10, and 50 wppm. The data indicate that surfactants reduce the severity of steam explosions. On average, the surfactant solutions resulted in a 65% reduction in average peak pressures when compared with the deionized water results. However, very little difference in the mitigating effect of the surfactant solutions was observed as the concentration was increased beyond 5 wppm. Particle-size distribution results also indicated a mitigating effect on steam explosion severity, as a 19% reduction in participating melt mass fraction was observed when the surfactants were used

  19. Growth of anatase and rutile phase TiO{sub 2} nanoparticles using pulsed laser ablation in liquid: Influence of surfactant addition and ablation time variation

    Energy Technology Data Exchange (ETDEWEB)

    Chaturvedi, Amita, E-mail: amita-chaturvedi@rrcat.gov.in [Laser Material Processing Division, Raja Ramanna Centre for Advanced Technology, Indore 452013, MP (India); Joshi, M.P. [Laser Material Processing Division, Raja Ramanna Centre for Advanced Technology, Indore 452013, MP (India); Homi Bhabha National Institute, Training School Complex, Anushakti Nagar, Mumbai – 400094 (India); Mondal, P.; Sinha, A.K.; Srivastava, A.K. [Indus Synchrotron Utilization Division, Raja Ramanna Centre for Advanced Technology, Indore 452013, MP (India)

    2017-02-28

    Highlights: • Ablations of Ti metal target were carried out in DI water and in 0.001 M SDS solution for different times using PLAL process. • Different characterization studies have been carried out to confirm the growth of TiO{sub 2} nanoparticles in both the liquid mediums. • Anatase phase TiO{sub 2} nanoparticles were obtained in DI water and rutile phase in 0.001 M SDS aqueous solution. • In surfactant solution, longer time ablation leads depletion of SDS molecules causes growth of anatase phase for 90 min. • Our studies confirmed the role of liquid ambience conditions variation over the different phase formations of nanoparticles. - Abstract: Titanium dioxide (TiO{sub 2}) nanoparticles were grown using nanosecond pulsed laser ablation of Ti target in DI water and in 0.001 M sodium dodecyl sulfate (SDS) surfactant aqueous solution. Growth was carried out with varying ablation times i. e. 30 min, 60 min and 90 min. The objective of our study was to investigate the influence of variations in liquid ambience conditions on the growth of the nanoparticles in a pulsed laser ablation in liquid (PLAL) process. Size, composition and optical properties of the grown TiO{sub 2} nanoparticles were investigated using transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), optical absorption, photoluminescence (PL) spectroscopy and X-ray diffraction (XRD) studies. The obtained nanoparticles of TiO{sub 2} were found almost spherical in shape and polycrystalline in nature in both the liquid mediums i.e. DI water and aqueous solution of surfactant. Nanoparticles number density was also found to increase with increasing ablation time in both the liquid mediums. However crystalline phase of the grown TiO{sub 2} nanoparticles differs with the change in liquid ambience conditions. Selected area electron diffraction (SAED), PL and XRD studies suggest that DI water ambience is favorable for the growth of anatase phase TiO{sub 2} nanoparticles for all

  20. Fundamentals of surfactant sputtering

    International Nuclear Information System (INIS)

    Hofsaess, Hans; Zhang Kun

    2009-01-01

    We introduce a new sputter technique, utilizing the steady-state coverage of a substrate surface with up to 10 16 cm -2 of foreign atoms simultaneously during sputter erosion by combined ion irradiation and atom deposition. These atoms strongly modify the substrate sputter yield on atomic to macroscopic length scales and therefore act as surfactant atoms (a blend of 'surface active agent'). Depending on the surfactant-substrate combination, the novel technique allows enhanced surface smoothing, generation of novel surface patterns, shaping of surfaces and formation of ultra-thin films. Sputter yield attenuation is demonstrated for sputtering of Si and Fe substrates and different surfactant species using 5 keV Xe ions at different incidence angles and fluences up to 10 17 cm -2 . Analytical approaches and Monte Carlo simulations are used to predict the sputtering yield attenuation as function of surfactant coverage. For sputtering of Si with Au surfactants we observe high sputter yields despite a steady-state surfactant coverage, which can be explained by strong ion-induced interdiffusion of substrate and surfactant atoms and the formation of a buried Au x Si surfactant layer in dynamic equilibrium.

  1. Dynamic covalent surfactants

    NARCIS (Netherlands)

    Minkenberg, C.B.

    2012-01-01

    In this thesis the development of surfactant aggregates with fast exchange dynamics between the aggregated and non-aggregated state is described. Dynamic surfactant exchange plays an important role in natural systems, for instance in cell signaling, cell division, and uptake and release of cargo.

  2. Pulmonary surfactant and lung transplantation

    NARCIS (Netherlands)

    Erasmus, Michiel Elardus

    1997-01-01

    Pulmonary surfactant lowers the surface tension at the air-water interface inside the alveolus. This is achieved by adsorption of surfactant phospholipids at the air-water interface, a process controlled by surfactant-associated proteins, such as SP-A. In this way, surfactant prevents collapse of

  3. Surfactants in the environment.

    Science.gov (United States)

    Ivanković, Tomislav; Hrenović, Jasna

    2010-03-01

    Surfactants are a diverse group of chemicals that are best known for their wide use in detergents and other cleaning products. After use, residual surfactants are discharged into sewage systems or directly into surface waters, and most of them end up dispersed in different environmental compartments such as soil, water or sediment. The toxic effects of surfactants on various aquatic organisms are well known. In general, surfactants are present in the environment at levels below toxicity and in Croatia below the national limit. Most surfactants are readily biodegradable and their amount is greatly reduced with secondary treatment in wastewater treatment plants. The highest concern is the release of untreated wastewater or wastewater that has undergone primary treatment alone. The discharge of wastewater polluted with massive quantities of surfactants could have serious effects on the ecosystem. Future studies of surfactant toxicities and biodegradation are necessary to withdraw highly toxic and non-biodegradable compounds from commercial use and replace them with more environmentally friendly ones.

  4. Surfactant effects on protein structure examined by electrospray ionization mass spectrometry.

    Science.gov (United States)

    Loo, R. R.; Dales, N.; Andrews, P. C.

    1994-01-01

    Electrospray ionization mass spectrometry (ESI-MS) has proven to be a useful tool for examining noncovalent complexes between proteins and a variety of ligands. It has also been used to distinguish between denatured and refolded forms of proteins. Surfactants are frequently employed to enhance solubilization or to modify the tertiary or quaternary structure of proteins, but are usually considered incompatible with mass spectrometry. A broad range of ionic, nonionic, and zwitterionic surfactants was examined to characterize their effects on ESI-MS and on protein structure under ESI-MS conditions. Solution conditions studied include 4% acetic acid/50% acetonitrile/46% H2O and 100% aqueous. Of the surfactants examined, the nonionic saccharides, such as n-dodecyl-beta-D-glucopyranoside, at 0.1% to 0.01% (w/v) concentrations, performed best, with limited interference from chemical background and adduct formation. Under the experimental conditions used, ESI-MS performance in the presence of surfactants was found to be unrelated to critical micelle concentration. It is demonstrated that surfactants can affect both the tertiary and quaternary structures of proteins under conditions used for ESI-MS. However, several of the surfactants caused significant shifts in the charge-state distributions, which appeared to be independent of conformational effects. These observations suggest that surfactants, used in conjunction with ESI-MS, can be useful for protein structure studies, if care is used in the interpretation of the results. PMID:7703844

  5. Enhanced removal of NAPL constituent from aquifer during surfactant flushing with aqueous hydraulic barriers of high viscosity.

    Science.gov (United States)

    Ahn, Dayoung; Choi, Jae-Kyeong; Kim, Heonki

    2017-06-07

    This study examines the effect of controlled groundwater flow paths induced by hydraulic barriers on the removal of NAPL constituent. An aqueous solution of thickener [0.05% (w/v) sodium carboxymethyl cellulose, SCMC] was continuously injected into a horizontally set two-dimensional physical model (sand-packed), forming aqueous plume(s) of high viscosity. The water flux at the down gradient of the model was measured using a flux tracer (n-octanol) and passive flux meter (PFM, packs of granular activated carbon). A non-reactive tracer (pentafluorobenzoic acid, PFBA) was used to identify the plume of high viscosity (hydraulic barrier) and ambient groundwater. When the barrier of high viscosity was formed, the plume was separated from the background water with little mixing, which was confirmed by the concentration profile of PFBA; whereas, the measured flux of ambient groundwater showed a distinctive distribution, due to the hydraulic barrier. When two barriers were set, the ambient water flux was enhanced in the middle, and the removal rate of PCE from the non-aqueous phase liquid (NAPL), measured by PFM, was found to improve by 26% during three hours of water flushing. When an aqueous solution of surfactant [0.37% (w/v), sodium dodecyl sulfate, SDS] was applied instead of water into the domain with two barriers set around the NAPL-contaminated spot, the removal of PCE from the NAPL increased by 101% for a three-hour time period. Based on the observations made in this study, hydraulic barriers formed by continuous injection of thickener solution change the flow direction of groundwater, and may increase the flux of groundwater (or aqueous solution of remediation agent) through a NAPL-contaminated region, improving the removal of NAPL.

  6. Preparation of microcapsules with multi-layers structure stabilized by chitosan and sodium dodecyl sulfate.

    Science.gov (United States)

    Chatterjee, Sudipta; Salaün, Fabien; Campagne, Christine; Vaupre, Suzy; Beirão, Alexandre

    2012-10-01

    The microcapsules with oil core and multi-layers shell were developed from poly-cationic chitosan (CS) and anionic SDS in multistep electrostatic layer by layer deposition technique combined with oil in water emulsification process. The net charge of microcapsules determined by zeta potential indicated that microcapsules are highly positive charged because of poly-cationic nature of CS, and charge neutralization of microcapsules occurred after alkali treatment. The granulometry measurement showed increase in average diameter of microcapsules by alkali treatment suggesting swelling or formation of small aggregates. The morphology analysis of microcapsules by optical microscopy corroborated the results of granulometry, and diameter of microcapsules was found to be decreased in multistep process due to tight packing of layers in outer shell of microcapsules. The alkali treatment of microcapsules to solidify outer shell was optimized with 0.02 N NaOH to reduce microcapsules aggregation and gel formation by CS chains as found in optical micrographs. Copyright © 2012 Elsevier Ltd. All rights reserved.

  7. Interaction of the amyloid β peptide with sodium dodecyl sulfate as a membrane-mimicking detergent.

    NARCIS (Netherlands)

    Hashemi, Shabestari M.; Meeuwenoord, N.J.; Filippov, D.V.; Huber, M.I.

    2016-01-01

    The amyloid β (A β) peptide is important in the context of Alzheimer's disease, since it is one of the major components of the fibrils that constitute amyloid plaques. Agents that can influence fibril formation are important, and of those, membrane mimics are particularly relevant, because the

  8. Sodium Dodecyl Sulfate (SDS)-Loaded Nanoporous Polymer as Anti-Biofilm Surface Coating Material

    DEFF Research Database (Denmark)

    Li, Li; Molin, Søren; Yang, Liang

    2013-01-01

    Biofilms cause extensive damage to industrial settings. Thus, it is important to improve the existing techniques and develop new strategies to prevent bacterial biofilm formation. In the present study, we have prepared nanoporous polymer films from a self-assembled 1,2-polybutadiene...

  9. Metathesis depolymerizable surfactants

    Science.gov (United States)

    Jamison, Gregory M [Albuquerque, NM; Wheeler, David R [Albuquerque, NM; Loy, Douglas A [Tucson, AZ; Simmons, Blake A [San Francisco, CA; Long, Timothy M [Evanston, IL; McElhanon, James R [Manteca, CA; Rahimian, Kamyar [Albuquerque, NM; Staiger, Chad L [Albuquerque, NM

    2008-04-15

    A class of surfactant molecules whose structure includes regularly spaced unsaturation in the tail group and thus, can be readily decomposed by ring-closing metathesis, and particularly by the action of a transition metal catalyst, to form small molecule products. These small molecules are designed to have increased volatility and/or enhanced solubility as compared to the original surfactant molecule and are thus easily removed by solvent extraction or vacuum extraction at low temperature. By producing easily removable decomposition products, the surfactant molecules become particularly desirable as template structures for preparing meso- and microstructural materials with tailored properties.

  10. Polymer-surfactant interactions studied by titration microcalorimetry : Influence of polymer hydrophobicity, electrostatic forces, and surfactant aggregational state

    NARCIS (Netherlands)

    Kevelam, J; van Breemen, J.F.L.; Blokzijl, W.; Engberts, J.B.F.N.

    1996-01-01

    Isothermal titration microcalorimetry has been applied to investigate the interactions between hydrophobically-modified water-soluble polymers and surfactants. The following polymers were used in this study: poly(sodium acrylate-co-n-alkyl methacrylate) (A), where n-alkyl = C9H19, C12H25, and C18H37

  11. Phosphine oxide surfactants revisited.

    Science.gov (United States)

    Stubenrauch, Cosima; Preisig, Natalie; Laughlin, Robert G

    2016-04-01

    This review summarizes everything we currently know about the nonionic surfactants alkyl dimethyl (C(n)DMPO) and alkyl diethyl (C(n)DEPO) phosphine oxide (PO surfactants). The review starts with the synthesis and the general properties (Section 2) of these compounds and continues with their interfacial properties (Section 3) such as surface tension, surface rheology, interfacial tension and adsorption at solid surfaces. We discuss studies on thin liquid films and foams stabilized by PO surfactants (Section 4) as well as studies on their self-assembly into lyotropic liquid crystals and microemulsions, respectively (Section 5). We aim at encouraging colleagues from both academia and industry to take on board PO surfactants whenever possible and feasible because of their broad variety of excellent properties. Copyright © 2016 Elsevier B.V. All rights reserved.

  12. Electronic Conductivity of Polypyrrole−Dodecyl Benzene Sulfonate Complexes

    DEFF Research Database (Denmark)

    West, Keld; Bay, Lasse; Nielsen, Martin Meedom

    2004-01-01

    and therefore smaller hopping distances. This was supported by X-ray measurements. Synthesis at lower temperatures generally leads to higher conductivity. The conductivity is strongly dependent on the potential, being more than four magnitudes smaller for the reduced state where the number of electronic......The electronic conductivity of the electroactive polymer polypyrrole-dodecyl benzene sulfonate (PPy-DBS) has been characterized as function of the redox level. The polymer was synthesized with different isomers of the dopant anions: the common mixed DBS tenside and three well-defined synthetic....... These investigations demonstrate that even minor differences in the dopant anion can cause significant changes in the physical properties of the electroactive polymer. The highest conductivities ($sigma$-25$/ = 39 Scm$+-1$/) are obtained by the (6D)BS isomer, perhaps because the branching leads to denser packing...

  13. Chemiluminescence of phthalhydrazide derivatives in organized media: Interactions with surfactants and cyclodextrins

    Energy Technology Data Exchange (ETDEWEB)

    Maeztu, Raquel [Departamento de Quimica y Edafologia, Facultad de Ciencias, Universidad de Navarra, 31080 Pamplona (Spain); Gonzalez-Gaitano, Gustavo, E-mail: gaitano@unav.e [Departamento de Quimica y Edafologia, Facultad de Ciencias, Universidad de Navarra, 31080 Pamplona (Spain); Tardajos, Gloria [Departamento de Quimica-Fisica I, Facultad de CC. Quimicas, Universidad Complutense, 28040 Madrid (Spain); Stilbs, Peter [Division of Physical Chemistry and Industrial NMR Centre, Department of Chemistry, Royal Institute of Technology, SE-10044, Stockholm (Sweden)

    2011-04-15

    The chemiluminescent oxidation of some phthalhydrazide derivatives, luminol (LUM), isoluminol (ISOL), N-(4-aminobutyl)-N-ethylisoluminol (ABEI) and N-(6-aminohexyl)-N-ethylisoluminol (AHEI), has been carried out in micellar media and in the presence of natural cyclodextrins (CDs), using Co(II) as catalyst and H{sub 2}O{sub 2} as oxidant. The cationic cetyltrimethylammonium bromide (CTAB) and, in a lesser extent, the anionic sodium dodecyl sulfate (SDS) produce quenching in the chemiluminescence (CL) of all the luminophores at concentrations above the cmc, whereas slight enhancements are attained with the non-ionic pentaethylene glycol monododecyl ether (C{sub 12}E{sub 5}). On the contrary, the incorporation of the CDs to the reaction produces a remarkable intensification of the CL. Binding of the luminophores to the macrocycles and the micelles has been studied by Pulsed-Gradient-Spin-Echo-NMR (PGSE-NMR) and fluorescence anisotropy. The cationic CTAB decreases the emission mainly due to charge compensation as a result of the association of the luminophores and the luminescent intermediates to the micelles. The presence of the alkyl substituents of ABEI and AHEI provides an additional hydrophobic contribution to the binding process. SDS quenches this reaction as the micelles retain Co(II) on their anionic layer. The protection and stabilization of these luminophores or their luminescent intermediates provided by the cavities of the CDs make this family of cyclic oligosaccharides much more suitable agents than the surfactants for enhancing the CL in aqueous media for this specific reaction. - Research highlights: Natural cyclodextrins act as boosters of the chemiluminescence of luminol and its derivatives. Cyclodextrins can be successfully employed for improving the possibilities of those applications that make use of the CL of luminol and its derivatives as a detection or quantification method. Ionic and non-ionic surfactants do not either enhance or even quench the

  14. Surfactant-Enhanced Organic Acid Inactivation of Tulane Virus, a Human Norovirus Surrogate.

    Science.gov (United States)

    Lacombe, Alison; Niemira, Brendan A; Gurtler, Joshua B; Kingsley, David H; Li, Xinhui; Chen, Haiqiang

    2018-02-01

    Combination treatments of surfactants and phenolic or short-chain organic acids (SCOA) may act synergistically or additively as sanitizers to inactive foodborne viruses and prevent outbreaks. The purpose of this study was to investigate the effect of gallic acid (GA), tannic acid, p-coumaric acid, lactic acid (LA), or acetic acid (AA), in combination with sodium dodecyl sulfate (SDS), against Tulane virus (TV), a surrogate for human norovirus. An aqueous stock solution of phenolic acids or SCOA with or without SDS was prepared and diluted in a twofold dilution series to 2× the desired concentration with cell growth media (M119 plus 10% fetal bovine serum). The solution was inoculated with an equal proportion of 6 log PFU/mL TV with a treatment time of 5 min. The survival of TV was quantified using a plaque assay with LLC-MK2 cells. The minimum virucidal concentration was 0.5:0.7% (v/v) for LA-SDS at pH 3.5 (4.5-PFU/mL reduction) and 0.5:0.7% (v/v) AA-SDS at pH 4.0 (2.6-log PFU/mL reduction). GA and SDS demonstrated a minimum virucidal concentration of 12.5 mM GA-SDS at pH 7.0 (0.2:0.3% GA-SDS) with an 0.8-log PFU/mL reduction and 50 mM GA-SDS (0.8:1.4% GA-SDS at pH 7.0) increased log reduction to 1.6 log PFU/mL. The combination treatments of AA or LA with SDS at pH 7.0 did not produce significant log reduction, nor did individual treatments of tannic acid, GA, p-coumaric acid, AA, LA, or SDS. This study demonstrates that a surfactant, such as SDS, aids in the phenolic acid and SCOA toxicities against viruses. However, inactivation of TV by combination treatments is contingent upon the pH of the sanitizing solution being lower than the pK a value of the organic acid being used. This information can be used to develop sanitizing washes to disinfect food contact surfaces, thereby aiding in the prevention of foodborne outbreaks.

  15. Conductive Hybrid Crystal Composed from Polyoxomolybdate and Deprotonatable Ionic-Liquid Surfactant

    Directory of Open Access Journals (Sweden)

    Jun Kobayashi

    2016-06-01

    Full Text Available A polyoxomolybdate inorganic-organic hybrid crystal was synthesized with deprotonatable ionic-liquid surfactant. 1-dodecylimidazolium cation was employed for its synthesis. The hybrid crystal contained δ-type octamolybdate (Mo8 isomer, and possessed alternate stacking of Mo8 monolayers and interdigitated surfactant bilayers. The crystal structure was compared with polyoxomolybdate hybrid crystals comprising 1-dodecyl-3-methylimidazolium surfactant, which preferred β-type Mo8 isomer. The less bulky hydrophilic moiety of the 1-dodecylimidazolium interacted with the δ-Mo8 anion by N–H···O hydrogen bonds, which presumably induced the formation of the δ-Mo8 anion. Anhydrous conductivity of the hybrid crystal was estimated to be 5.5 × 10−6 S·cm−1 at 443 K by alternating current (AC impedance spectroscopy.

  16. Surfactant addition and alternating current electrophoretic oscillation during size fractionation of nanoparticles in channels with two or three different height segments.

    Science.gov (United States)

    Xuan, Jie; Hamblin, Mark N; Stout, John M; Tolley, H Dennis; Maynes, R Daniel; Woolley, Adam T; Hawkins, Aaron R; Lee, Milton L

    2011-12-16

    An array of parallel planar nanochannels containing two or three segments with varying inner heights was fabricated and used for size fractionation of inorganic and biological nanoparticles. A liquid suspension of the particles was simply drawn through the nanochannels via capillary action. Using fluorescently labeled 30 nm polyacrylonitrile beads, different trapping behaviors were compared using nanochannels with 200-45 nm and 208-54-30 nm height segments. Addition of sodium dodecyl sulfate (SDS) surfactant to the liquid suspension and application of an AC electric field were shown to aid in the prevention of channel clogging. After initial particle trapping at the segment interfaces, significant particle redistribution occurred when applying a sinusoidal 8V peak-to-peak oscillating voltage with a frequency of 150 Hz and DC offset of 4V. Using the 208-54-30 nm channels, 30 nm hepatitis B virus (HBV) capsids were divided into three fractions. When the AC electric field was applied to this trapped sample, all of the virus particles passed through the interfaces and accumulated at the channel ends. Copyright © 2011 Elsevier B.V. All rights reserved.

  17. Modeling the effects of surfactant, hardness, and natural organic matter on deposition and mobility of silver nanoparticles in saturated porous media.

    Science.gov (United States)

    Park, Chang Min; Heo, Jiyong; Her, Namguk; Chu, Kyoung Hoon; Jang, Min; Yoon, Yeomin

    2016-10-15

    This study aims to provide insights into the mechanisms governing the deposition and retention of silver nanoparticles (AgNPs) in saturated porous media. Column experiments were conducted with quartz sand under saturated conditions to investigate the deposition kinetics of AgNPs, their mobility at different groundwater hardnesses (10-400 mg/L as CaCO3), and humic acid (HA, 0-50 mg/L as dissolved organic carbon [DOC]). An anionic surfactant, sodium dodecyl sulfate (SDS), was used as a dispersing agent to prepare a SDS-AgNPs suspension. The deposition kinetics of AgNPs were highly sensitive to the surfactant concentration, ionic strength, and cation type in solution. The breakthrough curves (BTCs) of SDS-AgNPs suggested that the transport and retention were influenced by groundwater hardness and HA. At low water hardness and high HA, high mobility of SDS-AgNPs was observed in saturated conditions. However, the retention of SDS-AgNPs increased substantially in very hard water with a low concentration of HA, because of a decreased primary energy barrier and the straining effect during the course of transport experiments. A modified clean-bed filtration theory and a two-site kinetic attachment model showed good fits with the BTCs of SDS-AgNPs. The fitted model parameters (katt and kstr) could be used successfully to describe that the retention behaviors were dominated by electrostatic and electrosteric repulsion, based on extended Derjaguin-Landau-Vaerwey-Overbeek calculations. Copyright © 2016 Elsevier Ltd. All rights reserved.

  18. Surfactant-Induced Ordering and Wetting Transitions of Droplets of Thermotropic Liquid Crystals “Caged” Inside Partially Filled Polymeric Capsules

    Science.gov (United States)

    2015-01-01

    We report a study of the wetting and ordering of thermotropic liquid crystal (LC) droplets that are trapped (or “caged”) within micrometer-sized cationic polymeric microcapsules dispersed in aqueous solutions of surfactants. When they were initially dispersed in water, we observed caged, nearly spherical droplets of E7, a nematic LC mixture, to occupy ∼40% of the interior volume of the polymeric capsules [diameter of 6.7 ± 0.3 μm, formed via covalent layer-by-layer assembly of branched polyethylenimine and poly(2-vinyl-4,4-dimethylazlactone)] and to contact the interior surface of the capsule wall at an angle of ∼157 ± 11°. The internal ordering of LC within the droplets corresponded to the so-called bipolar configuration (distorted by contact with the capsule walls). While the effects of dodecyltrimethylammonium bromide (DTAB) and sodium dodecyl sulfate (SDS) on the internal ordering of “free” LC droplets are similar, we observed the two surfactants to trigger strikingly different wetting and configurational transitions when LC droplets were caged within polymeric capsules. Specifically, upon addition of SDS to the aqueous phase, we observed the contact angles (θ) of caged LC on the interior surface of the capsule to decrease, resulting in a progression of complex droplet shapes, including lenses (θ ≈ 130 ± 10°), hemispheres (θ ≈ 89 ± 5°), and concave hemispheres (θ designs of LC-droplet-based responsive soft matter that cannot be realized in dispersions of free droplets. PMID:24911044

  19. Changes in fluorescent dissolved organic matter upon interaction with anionic surfactant as revealed by EEM-PARAFAC and two dimensional correlation spectroscopy.

    Science.gov (United States)

    Maqbool, Tahir; Hur, Jin

    2016-10-01

    Surfactants are present in significant amounts in both domestic and industrial wastewater, which may interact with dissolved organic matter (DOM). The present study investigated the interactions of sodium dodecyl sulfate (SDS) with three different DOM solutions, including bovine serum albumin (BSA), humic acid (HA), and the mixture of the two (BSA-HA), based on two advanced spectroscopic tools: excitation emission matrix (EEM) combined with parallel factor analysis (EEM-PARAFAC) and two dimensional correlation spectroscopy (2D-COS). The responses of two protein-like components to the addition of SDS differed depending the presence and the absence of HA. A decreasing and an increasing trend was observed for tryptophan-like (C1) and tyrosine-like (C2) components, respectively, in the BSA solution, while the BSA-HA mixture exhibited increasing fluorescence trends for both protein-like components. The conflicting results suggest that HA plays a secondary role in the protein-SDS interactions. No interaction between the SDS and humic-like component was found. 2D-COS combined with fluorescence spectra demonstrated that the protein-SDS interaction occurred on the order of C2 > C1 for the BSA solution but C1 > C2 for the BSA-HA mixture. Analyses of Scatchard plots confirmed the sequential order interpreted from 2D-COS, showing consistent trends in the binding constants. However, the presence of HA affected the protein-SDS interactions in different manners for C1 and C2, enhancing and reducing the binding constants, respectively. Circular dichroism spectra confirmed the occurrence of conformational changes in BSA with SDS. EEM-PARAFAC and 2D-COS successfully explained different interactions of surfactant with protein-like components in the presence of HA. Copyright © 2016 Elsevier Ltd. All rights reserved.

  20. Reactions of N2O5 with Salty and Surfactant-Coated Glycerol: Interfacial Conversion of Br- to Br2 Mediated by Alkylammonium Cations.

    Science.gov (United States)

    Shaloski, Michael A; Gord, Joseph R; Staudt, Sean; Quinn, Sarah L; Bertram, Timothy H; Nathanson, Gilbert M

    2017-05-18

    Gas-liquid scattering and product-yield experiments are used to investigate reactions of N 2 O 5 with glycerol containing Br - and surfactant ions. N 2 O 5 oxidizes Br - to Br 2 for every solution tested: 2.7 M NaBr, 0.03 M tetrahexylammonium bromide (THABr), 0.03 M THABr + 0.5 M NaBr, 0.03 M THABr + 0.5 M NaCl, 0.03 M THABr + 0.01 M sodium dodecyl sulfate (SDS), and 0.01 M cetyltrimethylammonium bromide (CTABr). N 2 O 5 also reacts with glycerol itself to produce mono- and dinitroglycerin. Surface tension measurements indicate that 0.03 M THABr and 2.7 M NaBr have similar interfacial Br - concentrations, though their bulk Br - concentrations differ by 90-fold. We find that twice as much Br 2 is produced in the presence of THA + , implying that the conversion of Br - to Br 2 is initiated at the interface, perhaps mediated by the charged, hydrophobic pocket within the surface THA + cation. The addition of 0.5 M NaBr, 0.5 M NaCl, or 0.01 M SDS to 0.03 M THABr lowers the Br 2 production rate by 23%, 63%, and 67% of the THABr value, respectively. When CTA + is substituted for THA + , Br 2 production drops to 12% of the THABr value. The generation of Br 2 under such different conditions implies that trace amounts of surface-active alkylammonium ions can catalyze interfacial N 2 O 5 reactions, even when salts and other surfactants are present.

  1. Adsorption of phenanthrene, 2-naphthol, and 1-naphthylamine to colloidal oxidized multiwalled carbon nanotubes: effects of humic acid and surfactant modification.

    Science.gov (United States)

    Hou, Lei; Zhu, Dongqiang; Wang, Ximeng; Wang, Lilin; Zhang, Chengdong; Chen, Wei

    2013-03-01

    Carbon nanotubes (CNTs) can exist in the form of colloidal suspension in aquatic environments, particularly in the presence of natural organic matter or surfactants, and may significantly affect the fate and transport of organic contaminants. In the present study, the authors examined the adsorption of phenanthrene, 2-naphthol, and 1-naphthylamine to three colloidal CNTs, including a stable suspension of oxidized multiwalled carbon nanotubes (O-MWNT), a humic acid (HA)-modified colloidal O-MWNT, and a sodium dodecyl sulfate (SDS)-modified colloidal O-MWNT. All three colloidal O-MWNTs exhibit strong adsorption affinities to the three test compounds (with K(OC) values orders of magnitude greater than those of natural organic matter), likely resulting from strong nonhydrophobic interactions such as π-π electron donor-acceptor interactions and Lewis acid-base interactions. When thoroughly mixed, HA (at ∼310 mg HA/g CNT) and SDS (at ∼750 mg SDS/g CNT) significantly affected the aggregation properties of O-MWNT, causing individually dispersed tubes to form a loosely entangled network. The effects of HA or SDS modification on adsorption are twofold. Adsorption of HA/SDS significantly reduces surface areas of O-MWNT; however, the entangled network allows adsorbate molecules to interact simultaneously with multiple tubes. An important implication is that humic substances and surfactant-like materials not only facilitate the formation of colloidal carbon nanoparticles but also affect how these colloidal carbon nanoparticles adsorb organic contaminants. Copyright © 2013 SETAC.

  2. Surfactant effect on functionalized carbon nanotube coated snowman-like particles and their electro-responsive characteristics

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Ke; Liu, Ying Dan [Department of Polymer Science and Engineering, Inha University, Incheon 402-751 (Korea, Republic of); Choi, Hyoung Jin, E-mail: hjchoi@inha.ac.kr [Department of Polymer Science and Engineering, Inha University, Incheon 402-751 (Korea, Republic of)

    2012-10-15

    The core–shell structured snowman-like (SL) microparticles coated by functionalized multi-walled carbon nanotube (MWNT) were prepared in the presence of different surfactants including cationic surfactant-cetyl trimethylammonium bromide (CTAB) and anionic surfactant-sodium lauryl sulfate (SDS). The effect of surfactants on adsorption onto SL particles was characterized by scanning electron microscopy (SEM), thermogravimetric analysis (TGA) and conductivity. The cationic surfactant is found to be more effective than anionic surfactant for helping nanotube adsorbed onto microparticle due to the presence of electrostatic interaction between the functionalized MWNT and the surfactant. Furthermore, the MWNT/SL particles dispersed in silicone oil exhibited a typical fibril structure of the electrorheological characteristics under an applied electric field observed by an optical microscope (OM), in which the state of nanotubes wrapped on the particles strongly affects their electro-responsive characteristics.

  3. Evaluation of micellar properties of sodium dodecylbenzene ...

    Indian Academy of Sciences (India)

    ASHWANI KUMAR SOOD

    2018-03-27

    Mar 27, 2018 ... case of ionic surfactants, the effect of added salts on micellar behaviour is dependent on the counter ions.15,16. Although many studies have been devoted to the effect of commonly used salts on such behaviour, such reports on sodium dodecylbenzene sulphonate (SDBS) are rare.17–20 Moreover, the ...

  4. Interaction of diazepam with surfactants. Spectrophotometric and spectrofluorometric study

    Science.gov (United States)

    De La Guardia, M.; Rodilla, F.

    1986-03-01

    The interaction of diazepam with non-ionic, anionic and cationic surfactants has been studied spectrophotometrically and fluorometrically. It has been verified that the absorption spectrum of diazepam is not modified in micellar medium. However, a dramatic five-fold increase in fluorescence sensitivity is observed in the presence of sodium lauryl sulphate (SDS). The experimental conditions, temperature, pH and surfactant concentration have been optimized to improve the fluorometric determination of diazepam and a detection limit of 0,04 ppmhas been obtained.

  5. Improvement of bagasse become lignosulfonate surfactant for oil industry

    Science.gov (United States)

    Setiati, R.; Prakoso, S.; Siregar, S.; Marhaendrajana, T.; Wahyuningrum, D.; Fajriah, S.

    2018-01-01

    The aim of this research is to use bagasse as a raw material as an effort to enhance the petroleum acquisition. There are two steps of processing bagasse into surfactant lignosulfonate which are the separation process of lignin from bagasse and the sulfonation process of lignin into lignosulfonate. The formation of surfactant lignosulfonate is a result of reaction between ion lignin with bisulfit. The sulfonate group/cluster at lignosulfonate are hydrophilic group which causes lignosulfonate to have amphipathic structure (surfactant). The comparison uses infrared test result against the formed component in surfactant sodium lignosulfonate from bagasse. With the two crude oil samples used in phase test, it turned out that at some light petroleum sample which were mixed with surfactant lignosulfonate formed a middle phase emulsion, with middle phase emulsion stability happening after the second day with a comparison of 10 – 50%. Meanwhile the heavy crude oil did not form a middle phase emulsion at all. Therefore, it can be concluded that bagasse has enough potential to be processed into surfactant lignosulfonate and to be used as injection fluid in the EOR process in oil industries.

  6. Rational design of aromatic surfactants for graphene/natural rubber latex nanocomposites with enhanced electrical conductivity.

    Science.gov (United States)

    Mohamed, Azmi; Ardyani, Tretya; Abu Bakar, Suriani; Sagisaka, Masanobu; Umetsu, Yasushi; Hamon, J J; Rahim, Bazura Abdul; Esa, Siti Rahmah; Abdul Khalil, H P S; Mamat, Mohamad Hafiz; King, Stephen; Eastoe, Julian

    2018-04-15

    Graphene nanoplatelets (GNPs) can be dispersed in natural rubber matrices using surfactants. The stability and properties of these composites can be optimized by the choice of surfactants employed as stabilizers. Surfactants can be designed and synthesized to have enhanced compatibility with GNPs as compared to commercially available common surfactants. Including aromatic groups in the hydrophobic chain termini improves graphene compatibility of surfactants, which is expected to increase with the number of aromatic moieties per surfactant molecule. Hence, it is of interest to study the relationship between molecular structure, dispersion stability and electrical conductivity enhancement for single-, double-, and triple-chain anionic graphene-compatible surfactants. Graphene-philic surfactants, bearing two and three chains phenylated at their chain termini, were synthesized and characterized by proton nuclear magnetic resonance ( 1 H NMR) spectroscopy. These were used to formulate and stabilize dispersion of GNPs in natural rubber latex matrices, and the properties of systems comprising the new phenyl-surfactants were compared with commercially available surfactants, sodium dodecylsulfate (SDS) and sodium dodecylbenzenesulfonate (SDBS). Raman spectroscopy, field emission scanning electron microscopy (FESEM), atomic force microscopy (AFM), and high-resolution transmission electron microscopy (HRTEM) were used to study structural properties of the materials. Electrical conductivity measurements and Zeta potential measurements were used to assess the relationships between surfactant architecture and nanocomposite properties. Small-angle neutron scattering (SANS) was used to study self-assembly structure of surfactants. Of these different surfactants, the tri-chain aromatic surfactant TC3Ph3 (sodium 1,5-dioxo-1,5-bis(3-phenylpropoxy)-3-((3phenylpropoxy)carbonyl) pentane-2-sulfonate) was shown to be highly graphene-compatible (nanocomposite electrical conductivity

  7. Encapsulation of emulsion droplets by organo–silica shells

    NARCIS (Netherlands)

    Zoldesi, C.; Steegstra, Patrick; Imhof, Arnout

    2007-01-01

    Surfactant-stabilized emulsion droplets were used as templates for the synthesis of hollow colloidal particles. Monodisperse silicone oil droplets were prepared by hydrolysis and polymerization of dimethyldiethoxysiloxane monomer, in the presence of surfactant: sodium dodecyl sulphate (SDS, anionic)

  8. BEHAVIOR OF SURFACTANT MIXTURES AT SOLID/LIQUID AND OIL/LIQUID INTERFACES IN CHEMICAL FLOODING SYSTEMS

    Energy Technology Data Exchange (ETDEWEB)

    Prof. P. Somasundaran

    2002-09-30

    The aim of the project is to develop and evaluate efficient novel surfactant mixtures for enhanced oil recovery. Surfactant loss by adsorption or precipitation depends to a great extent on the type of surfactant complexes and aggregates formed. Such information as well as techniques to generate the information is lacking currently particularly for surfactant mixtures and surfactant/polymer systems. A novel analytical centrifuge application is explored during the last period to generate information on structures-performance relationship for different surfactant aggregates in solution and, in turn, at interfaces. To use analytical untracentrifuge for surfactant mixtures, information on partial specific volumes of single surfactants and their mixtures is required. Towards this purpose, surface tension and density measurements were performed to determine critical micellar concentrations (cmc), partial specific volumes of n-dodecyl-{beta}-Dmaltoside (DM), nonyl phenol ethoxylated decyl ether (NP-10) and their 1:1 mixtures at 25 C. Durchschlag's theoretical calculation method was adopted to calculate the partial specific volumes. Effects of temperature and mixing, as well as methods used for estimation on micellization and partial specific volumes were studied during the current period. Surface tension results revealed no interaction between the two surfactants in mixed micelles. Partial specific volume measurements also indicated no interaction in mixed micelles. Maximum adsorption density, area per molecule and free energy of micellization were also calculated. Partial specific volumes were estimated by two experimental methods: d{sub {rho}}/dc and V{sub {sigma}}. The difference between the results of using the two methods is within 0.5% deviation. It was found that the partial specific volume is concentration dependent and sensitive to changes in temperature. The information generated in this study will be used for the study of surfactant aggregate mass

  9. Sodium Oxybate

    Science.gov (United States)

    Sodium oxybate is used to prevent attacks of cataplexy (episodes of muscle weakness that begin suddenly and ... urge to sleep during daily activities, and cataplexy). Sodium oxybate is in a class of medications called ...

  10. Sodium Phosphate

    Science.gov (United States)

    Sodium phosphate is used in adults 18 years of age or older to empty the colon (large intestine, bowel) ... view of the walls of the colon. Sodium phosphate is in a class of medications called saline ...

  11. Itaconic Acid Based Surfactants: I. Synthesis and Characterization of Sodiumn-Octyl Sulfoitaconate Diester Anionic Surfactant.

    Science.gov (United States)

    Xu, Jun; Cao, Fengzhi; Li, Tong; Zhang, Shuai; Gao, Chuanhui; Wu, Yumin

    A novel itaconate-based surfactant, namely sodium n -octyl sulfoitaconate diester (SOSID), has been synthesized from itaconic acid (IA) and n -octanol by sulfonation and esterification reaction processes. The effects of reaction temperature, reaction time, molar ratios of n -octanol to IA and the catalyst dosage on the esterification were investigated. The chemical structure of the surfactants SOSID was characterized by means of LC-MS and confirmed by FT-IR and 1 H NMR spectroscopy. The surface tension γ and the critical micelle concentration (CMC) were determined as 25.02 mN/m and 4.0 × 10 -4 mol/L by using surface tensiometer at 20 °C. Further investigations showed that SOSID possess excellent wetting, emulsifying and lime soap dispersing properties.

  12. Study of the formation and solution properties of worm-like micelles formed using both N-hexadecyl-N-methylpiperidinium bromide-based cationic surfactant and anionic surfactant.

    Directory of Open Access Journals (Sweden)

    Zhihu Yan

    Full Text Available The viscoelastic properties of worm-like micelles formed by mixing the cationic surfactant N-hexadecyl-N-methylpiperidinium bromide (C16MDB with the anionic surfactant sodium laurate (SL in aqueous solutions were investigated using rheological measurements. The effects of sodium laurate and temperature on the worm-like micelles and the mechanism of the observed shear thinning phenomenon and pseudoplastic behavior were systematically investigated. Additionally, cryogenic transmission electron microscopy images further ascertained existence of entangled worm-like micelles.

  13. The Mechanism by Which Dodecyl Dimethyl Benzyl Ammonium Chloride Increased the Toxicity of Chlorpyrifos to Spodoptera exigua

    Directory of Open Access Journals (Sweden)

    Li Cui

    2017-07-01

    Full Text Available Beet armyworm, Spodoptera exigua (Hübner is one of the most destructive pests that causes significant losses in crops. Unfortunately, S. exigua have developed resistance toward the majority of insecticides. Synergists may provide an important choice to deal with the resistance problems. Dodecyl dimethyl benzyl ammonium chloride (DDBAC is a cationic surfactant, which displayed enhancement effect when combined with chlorpyrifos against S. exigua, giving enhancement factors of 1.50 and 1.57 at the concentrations of 90 and 810 mg L−1. In order to clarify the possible mechanisms, we investigate the effects of DDBAC on detoxification enzymes. However, DDBAC showed no inhibition on these enzymes activities. Meanwhile, scanning electron microscope images indicated DDBAC did not affect the cuticle super micro structure of S. exigua. The alterations in cuticular penetration rate have also been observed; indeed, it has been suggested that synergism is obtained by an acceleration of insecticide penetration through the cuticle. The chlorpyrifos penetration increased sharply when combined with 90 and 810 mg L−1 DDBAC, with only 12.6 and 8.5% of the initial chlorpyrifos recovered by external rinsing after 8 h. In contrast, when there was no DDBAC, more than 23.3% of the initial dose was recovered after 8 h.

  14. Diseases of Pulmonary Surfactant Homeostasis

    Science.gov (United States)

    Whitsett, Jeffrey A.; Wert, Susan E.; Weaver, Timothy E.

    2015-01-01

    Advances in physiology and biochemistry have provided fundamental insights into the role of pulmonary surfactant in the pathogenesis and treatment of preterm infants with respiratory distress syndrome. Identification of the surfactant proteins, lipid transporters, and transcriptional networks regulating their expression has provided the tools and insights needed to discern the molecular and cellular processes regulating the production and function of pulmonary surfactant prior to and after birth. Mutations in genes regulating surfactant homeostasis have been associated with severe lung disease in neonates and older infants. Biophysical and transgenic mouse models have provided insight into the mechanisms underlying surfactant protein and alveolar homeostasis. These studies have provided the framework for understanding the structure and function of pulmonary surfactant, which has informed understanding of the pathogenesis of diverse pulmonary disorders previously considered idiopathic. This review considers the pulmonary surfactant system and the genetic causes of acute and chronic lung disease caused by disruption of alveolar homeostasis. PMID:25621661

  15. Chemoenzymatic synthesis and properties of novel lactone-type anionic surfactants.

    Science.gov (United States)

    Mori, Keisuke; Matsumura, Shuichi

    2012-01-01

    Two series of lactone-type surfactants with and without a hexyl side chain were prepared by the cyclocondensation of dimethyl alkanedioates with unsaturated diols, such as cis-2-butene-1,4-diol and ricinoleyl alcohol, using a lipase, followed by the addition of hydrophilic 3-mercaptopropionic acid in the presence of triethylamine. The lactone-type surfactants showed clear cmc values and surface tension lowering in aqueous solution irrespective of the hexyl side chain. It was found that the cmc values of lactone-type surfactants were lower than that of typical anionics, e.g., sodium laurate, and the cmc value became lower with increasing size of the lactone ring. The adsorption area at the surface of the aqueous lactone-type surfactant solution was larger when compared to the corresponding non-lactone-type surfactants. Lactone-type surfactants without the hexyl side chain aggregated quickly, forming 3-10 nm micelles; on the other hand, lactone-type surfactants with the hexyl side chain formed significantly larger micelles. This is due to the steric hindrance of the hexyl group on the lactone ring. The solubilization ability of the lactone-type surfactants with a hexyl side chain was superior to those without a hexyl side chain. The lactone-type surfactants showed a high foaming power and low foaming stability. They were also biodegraded by activated sludge.

  16. Removal Efficiency of Different Gemini Surfactants and Related Modified Clay toChattonella marina.

    Science.gov (United States)

    Wang, Wen-Wen; Yan, Xin-Ya; Li, Yun-Hui; Yu, De-Ren; Li, Hong-Ye; Yang, Wei-Dong; Liu, Jie-Sheng

    2017-11-01

      To obtain new modified clays with excellent algae removal efficiency, three gemini surfactants including ethylene bis (dodecyl dimethyl ammonium chloride), ethylene bis (octadecyl dimethyl ammonium chloride) and ethylene bis (dodecyl dimethyl ammonium bromide) (EDAB), and a poly quaternary ammonium salt, poly dimethyl diallyl ammonium chloride, were screened with Chattonella marina. The four chemicals all exhibited high removal efficiencies against C. marina, with EDAB achieving the highest. A series of organ-clays with different ratios of EDAB were prepared, and the associated removal efficiencies were evaluated. The removal efficiencies of the organ-clays were improved by the EDAB intercalation and the organ-clay with 15% EDAB had the highest removal efficiency. The LC50 of EDAB intercalated clay for zebrafish and shrimp was much higher than the values of intercalated clay required to obtain a desirable removal efficiency of algae. Taken together, EDAB intercalated clay might be a potential alternative to control harmful algal blooms (HABs).

  17. Preparation of a Fluorocarbon Polymerizable Surfactant and Its Application in Emulsion Polymerization of Fluorine-Containing Acrylate

    Directory of Open Access Journals (Sweden)

    Meng Zhao

    2017-11-01

    Full Text Available A novel polymerizable fluorocarbon surfactant, perfluoro (4–methyl–3, 6–dioxaoct–7–ene sodium sulfonate (PSVNa, was synthesized and characterized. The fluorocarbon surfactant PSVNa and its mixture PSVNa/SDS were used as emulsifiers during the emulsion polymerization of DFHMA/MMA. The investigation of polymerization kinetics, particle size, and stability of the emulsions revealed that PSVNa has excellent emulsifying properties. The NMR spectrum of the copolymer and the detection of residual PSVNa show that more than 95% of the fluorocarbon surfactants have been linked to the polymer chains by radical polymerization, which will greatly reduce the environmental pollution caused by fluorinated surfactants.

  18. Stabilization of diketo tautomer of curcumin by premicellar anionic surfactants: UV-Visible, fluorescence, tensiometric and TD-DFT evidences.

    Science.gov (United States)

    Dutta, Anisha; Boruah, Bornali; Manna, Arun K; Gohain, Biren; Saikia, Palash M; Dutta, Robin K

    2013-03-01

    A newly observed UV band of aqueous curcumin, a biologically important molecule, in presence of anionic surfactants, viz., sodium dodecylsulfate (SDS), sodium dodecylbenzenesulfonate (SDBS), and sodium dodecylsulfonate (SDSN) in buffered aqueous solutions has been studied experimentally and theoretically. The 425 nm absorption band of curcumin disappears and a new UV-band is observed at 355 nm on addition of the surfactants in the submicellar concentration range which is reversed as the surfactant concentration approaches the critical micelle concentration (CMC). The observed spectral absorption, fluorescence intensity and surface tension behavior, under optimal experimental conditions of submicellar concentration ranges of the surfactants in the pH range of 2.00-7.00, indicate that the new band is due to the β-diketo tautomer of curcumin stabilized by interactions between curcumin and the anionic surfactants. The stabilization of the diketo tautomer by submicellar anionic surfactants described here as well as by submicellar cationic surfactant, reported recently, is unique as this is the only such behavior observed in presence of submicellar surfactants of both charge types. The experimental results are in good agreement with the theoretical calculations using ab initio density functional theory combined with time dependent density functional theory (TD-DFT) calculations. Copyright © 2012 Elsevier B.V. All rights reserved.

  19. Coacervation with surfactants: From single-chain surfactants to gemini surfactants.

    Science.gov (United States)

    Zhao, Weiwei; Wang, Yilin

    2017-01-01

    Coacervation is a spontaneous process during which a colloidal dispersion separates into two immiscible liquid phases: a colloid-rich liquid phase in equilibrium with a diluted phase. Coacervation is usually divided into simple coacervation and complex coacervation according to the number of components. Surfactant-based coacervation normally contains traditional single-chain surfactants. With the development of surfactants, gemini surfactants with two amphiphilic moieties have been applied to form coacervation. This review summarizes the development of simple coacervation and complex coacervation in the systems of single-chain surfactants and gemini surfactants. Simple coacervation in surfactant solutions with additives or at elevated temperature and complex coacervation in surfactant/polymer mixtures by changing charge densities, molecular weight, ionic strength, pH, or temperature are reviewed. The comparison between gemini surfactants and corresponding monomeric single-chain surfactants reveals that the unique structures of gemini surfactants endow them with higher propensity to generate coacervation. Copyright © 2016 Elsevier B.V. All rights reserved.

  20. Final report on the safety assessment of sodium cetearyl sulfate and related alkyl sulfates as used in cosmetics.

    Science.gov (United States)

    Fiume, Monice; Bergfeld, Wilma F; Belsito, Donald V; Klaassen, Curtis D; Marks, James G; Shank, Ronald C; Slaga, Thomas J; Snyder, Paul W; Alan Andersen, F

    2010-05-01

    Sodium cetearyl sulfate is the sodium salt of a mixture of cetyl and stearyl sulfate. The other ingredients in this safety assessment are also alkyl salts, including ammonium coco-sulfate, ammonium myristyl sulfate, magnesium coco-sulfate, sodium cetyl sulfate, sodium coco/hydrogenated tallow sulfate, sodium coco-sulfate, sodium decyl sulfate, sodium ethylhexyl sulfate, sodium myristyl sulfate, sodium oleyl sulfate, sodium stearyl sulfate, sodium tallow sulfate, sodium tridecyl sulfate, and zinc coco-sulfate. These ingredients are surfactants used at concentrations from 0.1% to 29%, primarily in soaps and shampoos. Many of these ingredients are not in current use. The Cosmetic Ingredient Review (CIR) Expert Panel previously completed a safety assessment of sodium and ammonium lauryl sulfate. The data available for sodium lauryl sulfate and ammonium lauryl sulfate provide sufficient basis for concluding that sodium cetearyl sulfate and related alkyl sulfates are safe in the practices of use and concentration described in the safety assessment.

  1. Cationic gemini surfactants with cleavable spacer: chemical hydrolysis, biodegradation, and toxicity.

    Science.gov (United States)

    Tehrani-Bagha, A R; Holmberg, K; van Ginkel, C G; Kean, M

    2015-07-01

    The paper describes synthesis and characterization of a new type of cationic gemini surfactant, which has dodecyl tails and a spacer that contains an ester bond. The nomenclature used to describe the structure is 12Q2OCO1Q12, with Q being a quaternary ammonium group and the numbers indicating the number of methylene or methyl groups. Due to the close proximity to the two quaternary ammonium groups, the ester bond is very stable on the acid side and very labile already at slightly alkaline conditions. The hydrolysis products are two single chain surfactants (i.e. 12Q2OH and 12Q1COOH) which are less surface active than the intact gemini surfactant. 12Q2OCO1Q12 was found to be readily biodegradable, i.e. it gave more than 60% biodegradation after 28 days. This is interesting because similar gemini surfactants but with ester bonds in the tails instead of the spacer, have previously been found not to be readily biodegradable. The gemini surfactant was found to be toxic to aquatic organisms (ErC50 value of 0.27 mg/l), although less toxic than the two hydrolysis products. Copyright © 2014 Elsevier Inc. All rights reserved.

  2. MICROBIAL SURFACTANTS. I. GLYCOLIPIDS

    Directory of Open Access Journals (Sweden)

    Pirog T. Р.

    2014-02-01

    Full Text Available The review is devoted to surface-active glycolipids. The general characteristics, the physiological role of the rhamnolipids, trehalose lipids, sophorolipids, mannosylerythritol lipids and their traditional producers — the representatives of the genera Pseudozyma, Pseudomonas, Rhodococcus and Candida are given. The detailed analysis of the chemical structure, the stages of the biosynthesis and the regulation of some low molecular glycolipids are done. The own experimental data concerning the synthesis intensification, the physiological role and the practical use of Rhodococcus erythropolis IMV Ac-5017, Acinetobacter calcoaceticus IMV B-7241 and Nocardia vaccinii IMV B-7405 surfactants, which are a complex of the glyco-, phospho-, amino- and neutral lipids (glycolipids of all strains are presented by trehalose mycolates are summarized. It was found that R. erythropolis IMV Ac-5017, A. calcoaceticus IMV B-7241 and N. vaccinii IMV B-7405 surfactants have protective, antimicrobial and antiadhesive properties. It was shown that R. erythropolis IMV Ac-5017, A. calcoaceticus IMV B-7241 and N. vaccinii IMV B-7405 surfactants preparation of cultural liquid intensified the degradation of oil in water due to the activation of the natural petroleum-oxidizing microflora.

  3. Surfactants at the Design Limit.

    Science.gov (United States)

    Czajka, Adam; Hazell, Gavin; Eastoe, Julian

    2015-08-04

    This article analyzes how the individual structural elements of surfactant molecules affect surface properties, in particular, the point of reference defined by the limiting surface tension at the aqueous cmc, γcmc. Particular emphasis is given to how the chemical nature and structure of the hydrophobic tails influence γcmc. By comparing the three different classes of surfactants, fluorocarbon, silicone, and hydrocarbon, a generalized surface packing index is introduced which is independent of the chemical nature of the surfactants. This parameter ϕcmc represents the volume fraction of surfactant chain fragments in a surface film at the aqueous cmc. It is shown that ϕcmc is a useful index for understanding the limiting surface tension of surfactants and can be useful for designing new superefficient surfactants.

  4. Enhanced electrochemical reduction of hydrogen peroxide on silver paste electrodes modified with surfactant and salt

    OpenAIRE

    Gonzalez-Macia, L.; Smyth, M.; Morrin, A.; Killard, A.

    2011-01-01

    The modification of silver paste electrodes with a combination of dodecyl benzenesulphonic acid and KCl has been shown to lead to significant enhancements of the electrochemical reduction of hydrogen peroxide. The catalytic enhancement was shown to be dependent on the concentration of the surfactant/salt solution, which resulted in increases of some 80-fold in amperometric response to hydrogen peroxide at – 0.1 V vs. Ag/AgCl, pH 6.8 over unmodified silver paste. Physical analysis showed modif...

  5. Sodium in diet

    Science.gov (United States)

    Diet - sodium (salt); Hyponatremia - sodium in diet; Hypernatremia - sodium in diet; Heart failure - sodium in diet ... The body uses sodium to control blood pressure and blood volume. Your body also needs sodium for your muscles and nerves to work ...

  6. The interaction of a model active pharmaceutical with cationic surfactant and the subsequent design of drug based ionic liquid surfactants.

    Science.gov (United States)

    Qamar, Sara; Brown, Paul; Ferguson, Steven; Khan, Rafaqat Ali; Ismail, Bushra; Khan, Abdur Rahman; Sayed, Murtaza; Khan, Asad Muhammad

    2016-11-01

    Interactions of active pharmaceutical ingredients (API) with surfactants remain an important research area due to the need to improve drug delivery systems. In this study, UV-Visible spectrophotometry was used to investigate the interactions between a model low molecular weight hydrophilic drug sodium valproate (SV) and cationic surfactant cetyltrimethylammonium bromide (CTAB). Changes in the spectra of SV were observed in pre- and post-micellar concentrations of CTAB. The binding constant (Kb) values and the number of drug molecules encapsulated per micelle were calculated, which posed the possibility of mixed micelle formation and strong complexation between SV and CTAB. These results were compared to those of a novel room temperature surface active ionic liquid, which was synthesized by the removal of inorganic counterions from a 1:1 mixture of CTAB and SV. In this new compound the drug now constitutes a building block of the carrier and, as such, has considerably different surfactant properties to its building blocks. In addition, enhanced solubility in a range of solvents, including simulated gastric fluid, was observed. The study provides valuable experimental evidence concerning the performance of drug based surfactant ionic liquids and how their chemical manipulation, without altering the architecture of the API, leads to control of surfactant behavior and physicochemical properties. In turn, this should feed through to improved and controlled drug release rates and delivery mechanisms, and the prevention of precipitation or formation of polymorphs typical of crystalline form APIs. Copyright © 2016 Elsevier Inc. All rights reserved.

  7. Partitioning of small amphiphiles at surfactant bilayer/water interfaces: an avoided level crossing muon spin resonance study.

    Science.gov (United States)

    Scheuermann, Robert; Tucker, Ian M; Dilger, Herbert; Staples, Ed J; Ford, Gary; Fraser, Stuart B; Beck, Bettina; Roduner, Emil

    2004-03-30

    The temperature-dependent variation of local environment and reorientation dynamics of the small amphiphile 2-phenylethanol in lamellar phase dispersions of the dichain cationic surfactants, 2,3-diheptadecyl ester ethoxypropyl-1,1,1-trimethylammonium chloride (DHTAC) and dioctadecyldimethylammonium chloride (DODMAC), and the nonionic surfactant, tetra(ethylene glycol) n-dodecyl ether (C12E4), have been determined using avoided level crossing muon spin resonance spectroscopy (ALC-muSR). For cosurfactant radicals the hydrophobic or hydrophilic character of the surrounding media can be determined from their magnetic resonance signatures. Comparison of the three different bilayer-forming surfactant systems shows that the ALC-muSR technique is able to distinguish both major and subtle differences in the partitioning of the cosurfactant radicals between the different systems.

  8. Halloysite Nanotubes Noncovalently Functionalised with SDS Anionic Surfactant and PS-b-P4VP Block Copolymer for Their Effective Dispersion in Polystyrene as UV-Blocking Nanocomposite Films

    Directory of Open Access Journals (Sweden)

    Lazaros Tzounis

    2017-01-01

    Full Text Available A simple and versatile method is reported for the noncovalent functionalisation of natural and “green” halloysite nanotubes (HNTs allowing their effective dispersion in a polystyrene (PS thermoplastic matrix via solvent mixing. Initially, HNTs (pristine HNTs were modified with physically adsorbed surfactant molecules of sodium dodecyl sulphate (SDS and PS-b-P4VP [P4