WorldWideScience

Sample records for surfactant slug contained

  1. Secondary oil recovery process. [two separate surfactant slugs

    Energy Technology Data Exchange (ETDEWEB)

    Fallgatter, W.S.

    1969-01-14

    Oil recovery by two separate surfactant slugs is greater than for either one alone. One slug contains a surfactant(s) in either oil or water. The other slug contains surfactant(s) in thickened water. The surfactants are sodium petroleum sulfonate (Promor SS20), polyoxyethylene sorbitan trioleate (Tween 85), lauric acid diethanolamide (Trepoline L), and sodium tridecyl sulfate polyglycol ether (Trepenol S30T). The thickener is carboxymethyl cellulose (Hercules CMC 70-S Medium thickener) or polyvinyl alcohol (Du Pont Elvanol 50-42). Consolidated sandstone cores were flooded with water, followed with Hawes crude, and finally salt water (5 percent sodium chloride) which recovered about 67 percent of the crude. A maximum of 27.5 percent of the residual oil was recovered by surfactant(s) in oil or water followed by fresh water, then surfactant(s) plus thickener in water followed by fresh water. Either surfactant slug may be injected first. Individually, each of the surfactant slugs can recover from about 3 to 11 percent less residual oil than their total recovery when used consecutively.

  2. Minimum slugging velocity in fluidized beds containing vertical rods

    Energy Technology Data Exchange (ETDEWEB)

    Coronella, C.J.; Lee, S.Y.; Seader, J.D. (University of Utah, Salt Lake City, UT (United States). Dept. of Chemical Engineering)

    1994-09-01

    A new method for determining the onset of slugging in fluidized beds is presented. Pressure-drop fluctuations, measured from below the distributor to the gas exit line, are transformed to the frequency domain by the power spectral desity function (PSDF). The dominant frequency of the PSDF corresponds to the eruption frequency of bubbles or slugs. A fluidized bed is in the slugging regime when this dominant frequency, f[sub d], remains constant with changing gas velocity. This method is an improvement over previous methods because of the simple nature of the apparatus required, and because it is possible to locate the pressure probes so that they do not interfere with the fluidization or undergo rapid wear from the constant particle movement. This method was used to determine the gas velocity corresponding to the transition from the bubbling to the slugging regime for a 10cm diameter bed of sand fluidized with air and containing three 1.9cm diameter vertical rods at 5.2cm centre-to-centre triangular spacing and extending the length of the bed, and to compare the results with those from the same bed without any internal rods. The presence of the vertical rods inhibited the onset of the slugging regime, and significantly extended the bubbling regime to higher gas velocities. 32 refs., 12 figs.

  3. Hydrocarbon recovery comprising injecting a slug comprising oil soluble alkoxylated surfactants from lignin

    Energy Technology Data Exchange (ETDEWEB)

    Naae, D.G.; DaGue, M.G.; Dunn, N.G.

    1993-07-27

    A method is described of recovering hydrocarbons from an underground hydrocarbon formation penetrated by at least one injection well and at least one production well, which comprises: injecting into the formation through an injection well a surfactant slug comprising about 0.1% to about 10% by weight of oil soluble surfactants produced from lignin, said oil soluble surfactants produced by placing lignin in contact with water, converting the lignin into relatively low molecular weight lignin phenols by reducing the lignin in the presence of a reducing agent of carbon monoxide or hydrogen, said reduction occurring at a temperature greater than about 200 C and a pressure greater than about 100 psi, recovering the oil soluble lignin phenols from the reaction mixture, alkoxylating the lignin phenols by reacting the lignin phenols with an a-olefin epoxide having about 6 to about 20 carbon atoms at about 100 to about 200 C for about 1 to about 3 hours in an organic solvent, and changing the alkoxylated lignin phenols into oil soluble lignin surfactants by a reaction selected from the group consisting of sulfonation, sulfation, and alkoxysulfation; injecting into the formation through the injection well a drive fluid to push the surfactant slug towards a production well; and recovering hydrocarbons at the production well.

  4. Epidermal secretions of terrestrial flatworms and slugs: Lehmannia valentiana mucus contains matrilin-like proteins.

    Science.gov (United States)

    Li, Dongmei; Graham, Lloyd D

    2007-11-01

    We describe the epidermal mucus of two types of terrestrial invertebrates: free-living flatworms (Tricladida: Terricola), and the slug Lehmannia valentiana (Gastropoda: Pulmonata). Both exhibited similar dry shear strengths (1.4-1.7 MPa). In denaturing gel electrophoresis, the protein fraction of flatworm mucus migrated mainly as a broad band (200-300 kDa). Slug mucus had a higher protein content than flatworm mucus but it contained more carbohydrate than protein, mainly as large heparan sulfate-like glycosaminoglycans. Proteins and glycosaminoglycans were both essential for the mechanical integrity of the slug hydrogel. The protein fraction of slug mucus contained approximately 12 larger proteins (30-300 kDa) and approximately 6 smaller ones (10-28 kDa). Complete cDNA clones were obtained for the slug mucus 40 kDa protein (Sm40; Genbank accession EF634345) and 85 kDa protein (Sm85; Genbank accession EF634346). Both proteins contain EGF-like repeats and von Willebrand A-domains, and therefore resemble vertebrate matrilins. Many of the larger slug mucus proteins appear to contain A-domains, and these may play a role in the unusual rheological properties of gastropod mucus.

  5. Spinodal Decomposition in Mixtures Containing Surfactants

    Science.gov (United States)

    Melenekvitz, J.

    1998-03-01

    Spinodal decomposition in mixtures containing two immiscible liquids (A and B) plus surfactant was investigated using a recently developed (J. Melenkevitz and S. H. Javadpour, J. Chem. Phys., 107, 623 (1997).) 3-component Ginzburg-Landau model. The time dependent Ginzburg-Landau (TDGL) equations governing the evolution of structure were numerically integrated in 2-dimensions. We found the growth rate of the average domain size, R(t), decreased with increasing surfactant concentration over a wide range of relative amounts of A and B. This can be attributed to the surfactant accumulating at the growing interface between the immiscible liquids, which leads to a reduction in the surface tension. At late times, the growth rate was noticeably altered when thermal fluctuations were added to the numerical simulations. In this case, power law behavior was observed for R(t) at late times, R(t) ~ t^α, with the exponent α decreasing as the amount of surfactant increased. The dynamics at early times were determined by linearizing the TDGL equations about a uniformly mixed state. The growth rate at ealry times was found to be strongly dependent on the model parameters describing the surfactant miscibility in A and B and the surfactant strength. Comparison with recent measurements on SBR / PB mixtures with added PB-SBR diblock copolymer will also be presented.

  6. Synthesis of novel quaternary ammonium surfactants containing adamantane

    Institute of Scientific and Technical Information of China (English)

    Jian Wei Guo; Xing Zhong; Hua Zhu; Li Juan Feng; Ying De Cui

    2012-01-01

    A series of novel quaternary ammonium surfactants containing adamantane were designed and synthesized from 1-adamantanecarboxylic acid.The structures of target surfactants were confirmed by 1H NMR,elements analysis and FTIR.Surface properties of these surfactants were investigated.Due to the lipophilicity of adamantane,the critical micelle concentration (CMC) and C20 values of the synthesized quaternary ammonium surfactants are lower than that of conventional quaternary ammonium surfactants.

  7. Surfactant analysis in oil-containing fluids

    Energy Technology Data Exchange (ETDEWEB)

    Gronsveld, J.; Faber, M.J. (Koninklijke Shell Exploratie en Produktie Laboratorium, Rijswijk (Netherlands))

    The total surfactant concentration in aqueous phase samples can be analysed with a potentiometric titration. In enhanced oil recovery research, however, the surfactant is produced not only in aqueous phase samples but also in oleic phase samples. The oleic constituents in the oliec phase samples interfere in the surfactant analysis and, therefore, the titration method has been adapted. (orig.).

  8. Interaction of Fluorocarbon Containing Hydrophobically Modified Polyelectrolyte with Nonionic Surfactants

    Institute of Scientific and Technical Information of China (English)

    GUO,Jin-Feng(郭金峰); ZHUANG,Dong-Qing(庄东青); ZHOU,Hui(周晖); ZHANG,Yun-Xiang(章云祥)

    2002-01-01

    The interaction of fluorocarbon containing hydrophobically modified polyelectrolyte (FMPAANa) with two kinds of nonionic surfactants (hydrogenated and fluorinated) in a semidilute (0.5 wt% ) aqueous solution had been studied by rheological measurements. Association behavior was found in both systems. The hydrophobic interaction of FMPAANa with fluorinated surfactant (FC171) is much stronger than that with hydrogenated surfactant (NP7.5) at low surfactant concentrations. The interaction is strengthened by surfactants being added for the density of active junctions increased. Whereas distinct phenomena for FC171 and NP7. 5 start to be found as the surfactants added over their respective certain concentration. The interaction of polyelectrolyte with fluorinated surfactant increases dramatical ly while that with hydrogenated surfactant decreases.

  9. Interfacial behavior of pulmonary surfactant preparations containing egg yolk lecithin.

    Science.gov (United States)

    Nakahara, Hiromichi; Shibata, Osamu

    2014-01-01

    Mammalian lungs are covered with lipid-protein complexes or pulmonary surfactants. In this work, which aimed towards the less expensive production of artificial pulmonary surfactants, we produced surfactants composed of egg yolk lecithin (eggPC), palmitic acid, and hexadecanol (= 0.30/0.35/0.35, mol/mol/mol ) containing different amounts of Hel 13-5 (NH2-KLLKLLLKLWLKLLKLLL-COOH) as a substitute for the proteins in native pulmonary surfactants. Surface pressure (π)-molecular area (A) and surface potential (DV)-A isotherms of the mixtures were measured via the Wilhelmy and ionizing (241)Am electrode methods, respectively. The interactions between the lipid components and Hel 13-5 led to variations in the surface pressure caused by the expulsion of fluid components from the surface. Furthermore, the π-A and DV-A isotherms featured large hysteresis loops for the surfactant that contained a small amount of Hel 13-5 during compression and successive expansion cycling. To elucidate the morphology, the phase behavior was visualized in situ at the air-water interface by means of fluorescence microscopy; the images suggested less effective interactions between Hel 13-5 and the unsaturated PC in eggPC despite the similarity of their monolayer properties.

  10. Production Technology and Physicochemical Properties of Composition Containing Surfactant Proteins

    Directory of Open Access Journals (Sweden)

    Valery V. Novochadov

    2016-06-01

    Full Text Available The article describes a production method of substance containing great amount of phospolipids (up to 36 % and surfactant proteins (up to 2 % in terms of lyophilisate composition. Basic physical and chemical characteristics of the substance (density, viscosity, surface tension and the coefficient of sliding friction indicate a high lubricant capacity of the derived product. These properties are kept when mixed with native human synovial fluid in the ratio of 1 to 9 inclusive. The obtained data allows to consider the derived composition, containing surfactant proteins and phospholipids, a variety of bionic lubricant suitable for testing as a potential equivalent of synovial fluid which can be used in traumatology and orthopedics, a cosmetic component or agent which increases the stability of the cell suspension during culturing in bioreactors.

  11. Surfactant/detergent titration analysis method and apparatus for machine working fluids, surfactant-containing wastewater and the like

    Science.gov (United States)

    Smith, D.D.; Hiller, J.M.

    1998-02-24

    The present invention is an improved method and related apparatus for quantitatively analyzing machine working fluids and other aqueous compositions such as wastewater which contain various mixtures of cationic, neutral, and/or anionic surfactants, soluble soaps, and the like. The method utilizes a single-phase, non-aqueous, reactive titration composition containing water insoluble bismuth nitrate dissolved in glycerol for the titration reactant. The chemical reaction of the bismuth ion and glycerol with the surfactant in the test solutions results in formation of micelles, changes in micelle size, and the formation of insoluble bismuth soaps. These soaps are quantified by physical and chemical changes in the aqueous test solution. Both classical potentiometric analysis and turbidity measurements have been used as sensing techniques to determine the quantity of surfactant present in test solutions. This method is amenable to the analysis of various types of new, in-use, dirty or decomposed surfactants and detergents. It is a quick and efficient method utilizing a single-phase reaction without needing a separate extraction from the aqueous solution. It is adaptable to automated control with simple and reliable sensing methods. The method is applicable to a variety of compositions with concentrations from about 1% to about 10% weight. It is also applicable to the analysis of waste water containing surfactants with appropriate pre-treatments for concentration. 1 fig.

  12. Surfactant/detergent titration analysis method and apparatus for machine working fluids, surfactant-containing wastewater and the like

    Science.gov (United States)

    Smith, Douglas D.; Hiller, John M.

    1998-01-01

    The present invention is an improved method and related apparatus for quantitatively analyzing machine working fluids and other aqueous compositions such as wastewater which contain various mixtures of cationic, neutral, and/or anionic surfactants, soluble soaps, and the like. The method utilizes a single-phase, non-aqueous, reactive titration composition containing water insoluble bismuth nitrate dissolved in glycerol for the titration reactant. The chemical reaction of the bismuth ion and glycerol with the surfactant in the test solutions results in formation of micelles, changes in micelle size, and the formation of insoluble bismuth soaps. These soaps are quantified by physical and chemical changes in the aqueous test solution. Both classical potentiometric analysis and turbidity measurements have been used as sensing techniques to determine the quantity of surfactant present in test solutions. This method is amenable to the analysis of various types of new, in-use, dirty or decomposed surfactants and detergents. It is a quick and efficient method utilizing a single-phase reaction without needing a separate extraction from the aqueous solution. It is adaptable to automated control with simple and reliable sensing methods. The method is applicable to a variety of compositions with concentrations from about 1% to about 10% weight. It is also applicable to the analysis of waste water containing surfactants with appropriate pre-treatments for concentration.

  13. Hydrolysis of Surfactants Containing Ester Bonds: Modulation of Reaction Kinetics and Important Aspects of Surfactant Self-Assembly

    Science.gov (United States)

    Lundberg, Dan; Stjerndahl, Maria

    2011-01-01

    The effects of self-assembly on the hydrolysis kinetics of surfactants that contain ester bonds are discussed. A number of examples on how reaction rates and apparent reaction orders can be modulated by changes in the conditions, including an instance of apparent zero-order kinetics, are presented. Furthermore, it is shown that the examples on…

  14. Initiation of slug flow

    Energy Technology Data Exchange (ETDEWEB)

    Hanratty, T.J.; Woods, B.D. [Univ. of Illinois, Urbana, IL (United States)

    1995-12-31

    The initiation of slug flow in a horizontal pipe can be predicted either by considering the stability of a slug or by considering the stability of a stratified flow. Measurements of the shedding rate of slugs are used to define necessary conditions for the existence of a slug. Recent results show that slugs develop from an unstable stratified flow through the evolution of small wavelength waves into large wavelength waves that have the possibility of growing to form a slug. The mechanism appears to be quite different for fluids with viscosities close to water than for fluids with large viscosities (20 centipoise).

  15. Aqueous behaviour of cationic surfactants containing a cleavable group.

    Science.gov (United States)

    Samakande, Austin; Chaghi, Radhouane; Derrien, Gaelle; Charnay, Clarence; Hartmann, Patrice C

    2008-04-01

    The aggregation behaviour of two novel cationic RAFT agents (transfer surfactants); N,N-dimethyl-N-(4-(((phenylcarbonothioyl)thio)methyl)benzyl)ethanammonium bromide (PCDBAB) and N-(4-((((dodecylthio)-carbonothioyl)thio)methyl)benzyl)-N,N-dimethylethanammonium bromide (DCTBAB) in diluted solutions have been investigated by surface tension, conductimetry and microcalorimetry measurements. The thermodynamic parameters i.e. the critical micelle concentration (cmc), the degree of micelle ionization (alpha), the head group surface area (a 0), Delta H mic, Delta G mic and T Delta S mic are reported at 303 K. The thermodynamic parameters have been compared to those of the conventional surfactant cetyltrimethylammonium bromide (CTAB) in order to specify structural relationships. The obtained results have been discussed considering the hydrophobic behaviour of the S-C=S- linkage and the specific interactions that arise from the introduction of the benzene ring into the hydrophobic part.

  16. Rheological Properties of the Aqueous Solution for Fluorocarbon-containing Hydrophobically Modified Sodium PolyacrylicAcid with Various Surfactants

    Institute of Scientific and Technical Information of China (English)

    GUO,Jin-Feng(郭金峰); ZHUANG,Dong-Qing(庄东青); ZHOU,Hui(周晖); ZHANG,Yun-Xiang(章云祥)

    2001-01-01

    The interaction of fluorocarbon-containing hydrophobicallymodified sodiun polyacryiic acid (FMPAANa) (0.5 wt% )with various surfactants (anionic,nonionic and cationic) hasbeen investigated by theological measurements.Different rhe-ological behaviors are displayed for ionic surfactants and non-ionic surfactants.Fluorinated surfactants have stronger affini-ty with polyelectrolyte hydrophobes comparing with hydro-genated surfactants.The hydrophobic association of FM-PAANa with a cationic surfactant (CTAB) and a fluorinatednonionic surfactant (FC171) is much stronger than with anonionic surfactant (NP7.5 ) and an anionic surfactant(FC143).Further investigation of the effects of temperatureon solution properties shows that the dissociation energy Em iscorrelated to the strength of the aggregated junctions.``

  17. Purification of firefighting water containing a fluorinated surfactant by reverse osmosis coupled to electrocoagulation-filtration

    OpenAIRE

    Baudequin, Clement; Couallier, Estelle; Rakib, Mohammed; Deguerry, Isabelle; Severac, Romain; Pabon, Martial

    2011-01-01

    International audience; Extinguishments of large scale solvent fires produce large amounts of water that may contain various fluorinated surfactants depending on the type of fire fighting foam used. Due to their chemical nature, fluorinated parts of fl uorinated compounds are highly resistant to biochemical and advanced oxidation processes. Therefore the current treatment for the degradation of fluorinated surfactant from water used in fire extinguishment is high temperature incineration of t...

  18. Coarsening of firefighting foams containing fluorinated hydrocarbon surfactants

    Science.gov (United States)

    Kennedy, Matthew J.; Dougherty, John A.; Otto, Nicholas; Conroy, Michael W.; Williams, Bradley A.; Ananth, Ramagopal; Fleming, James W.

    2013-03-01

    Diffusion of gas between bubbles in foam causes growth of large bubbles at the expense of small bubbles and leads to increasing mean bubble size with time thereby affecting drainage. Experimental data shows that the effective diffusivity of nitrogen gas in aqueous film forming foam (AFFF), which is widely used in firefighting against burning liquids, is several times smaller than in 1% sodium dodecyl sulfate (SDS) foam based on time-series photographs of bubble size and weighing scale recordings of liquid drainage. Differences in foam structure arising from foam production might contribute to the apparent difference in the rates of coarsening. AFFF solution produces wetter foam with initially smaller bubbles than SDS solution due in part to the lower gas-liquid surface tension provided by the fluorosurfactants present in AFFF. Present method of foam production generates microbubble foam by high-speed co-injection of surfactant solution and gas into a tube of 3-mm diameter. These results contribute to our growing understanding of the coupling between foam liquid fraction, bubble size, surfactant chemistry, and coarsening. NRC Resident Research Associate at NRL

  19. The Alkali/Surfactant/ Polymer Process: Effects of Slug Size, Core Length and a Chase Polymer Le procédé alkali/surfactant/polymère : effets de la taille du bouchon, de la longueur de la carotte et d'un polymère de déplacement

    Directory of Open Access Journals (Sweden)

    Green K. A.

    2006-11-01

    Full Text Available An experimental study was conducted to examine the effects of slug size, core length, and a chase polymer on the effectiveness of the alkali/surfactant/polymer (A/S/P process in recovering waterflood residual oil. Core flood experiments were conducted with unfired linear Berea sandstone cores. The tertiary oil recovery, oil cut, pressure drop, and chemical propagation were measured for each flood. Tertiary oil recovery significantly increased with the slug size up to 0. 5 of a pore volume. Increasing the slug size further resulted in a smaller incremental increase in oil recovery. A slight increase in tertiary oil recovery was obtained when small size A/S/P slugs were followed with achase polymer having a viscosity higher than the slug. The lack of oil recovery with small A/S/P slugs was due to the consumption and dilution of the injected chemicals, especially the synthetic surfactant, due to adsorption and dispersion. Increasing the core length by a factor of 4. 5 (from 9 to 40. 6 cm had no significant effect on tertiary oil recovery. Chemical propagation was found to be a function of core length (i. e. , core Peclet number and the size of the chase polymer slug. Increasing core length and employing a chase polymer maintained the integrity of the A/S/P slug by decreasing the effect of dispersion and minimizing the influence of viscous fingering at the tail of the A/S/P slug. Une étude expérimentale a été effectuée pour examiner les effets de la taille du bouchon, de la longueur de la carotte et de l'emploi d'un polymère de déplacement sur l'efficacité du procédé A/S/P (alkali/surfactant/polymère dans la récupération d'huile résiduelle par injection d'eau. Les expériences d'injection ont été faites avec des carottes rectilignes en grès de Berea vert. La récupération tertiaire du pétrole, la présence d'eau, la perte de charge et la propagation chimique ont été mesurées pour chaque injection. La récupération tertiaire du

  20. Features of the micellar solubility of metal-containing surfactants in hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Fedorov, A.B.; Zdobnova, O.L.; Zaichenko, L.P.; Proskuryakov, V.A.

    1988-03-10

    Metal-containing surfactants (SF) are now widely used as different additives to oils and fuels. The micellar solubility of a series of individual metal-containing SF and widely used additives was investigated as a function of the structure and polarity of the additive, type of hydrocarbon solvent, and presence of water in this study. Individual decyl benzenesulfonates (DBS) of different metals and samples of surfactant additives for oils of the alkylphenolate (VNII NP-370), sulfonate (PMSA, PMSya, S-150, S-300, Lubrizol 58, SB-3, PMSya (bariated), alkylsalicylate (ASK, MASK), and dialkyldithiophosphate (DF-11, VNII NP-354) types were investigated.

  1. Microwave corneosurfametry: a minute assessment of the skin compatibility of surfactant-containing products.

    Science.gov (United States)

    Goffin, V; Piérard-Franchimont, C; Piérard, G E

    1997-11-01

    Surfactants may elicit several undesirable effects on the skin. The stratum corneum is one of the targets showing primary changes after a short contact with detergents. Corneosurfametry was introduced as an ex vivo bioassay to assess the interaction and compatibility of surfactants with human stratum corneum. The present work introduces a variant of the regular corneosurfametry test. Microwaving set at 750 W for 30 s was used to shorten the duration of the technical procedure and to allow the rating of neat surfactant-containing products. The color of samples (L.* and Chroma C*) was measured to derive the colorimetric index of mildness (CIM), the values of which rise from 0 to 70 with increasing surfactant mildness toward human stratum corneum. Data were compared with standard corneosurfametry performed at 20 and 40°C. Data indicate that increasing the temperature of the test solutions and microwaving alter the CIM values of most surfactants. Only the most gentle products are little affected. An overall good correlation exists between the regular and microwave corneosurfametry data. Microwave corneosurfametry is a new sensitive tool for predicting skin compatibility of surfactants.

  2. Mechanical Properties of Fiber Reinforced Lightweight Concrete Containing Surfactant

    Directory of Open Access Journals (Sweden)

    Yoo-Jae Kim

    2010-01-01

    Full Text Available Fiber reinforced aerated lightweight concrete (FALC was developed to reduce concrete's density and to improve its fire resistance, thermal conductivity, and energy absorption. Compression tests were performed to determine basic properties of FALC. The primary independent variables were the types and volume fraction of fibers, and the amount of air in the concrete. Polypropylene and carbon fibers were investigated at 0, 1, 2, 3, and 4% volume ratios. The lightweight aggregate used was made of expanded clay. A self-compaction agent was used to reduce the water-cement ratio and keep good workability. A surfactant was also added to introduce air into the concrete. This study provides basic information regarding the mechanical properties of FALC and compares FALC with fiber reinforced lightweight concrete. The properties investigated include the unit weight, uniaxial compressive strength, modulus of elasticity, and toughness index. Based on the properties, a stress-strain prediction model was proposed. It was demonstrated that the proposed model accurately predicts the stress-strain behavior of FALC.

  3. Surfactant treatment before first breath for respiratory distress syndrome in preterm lambs: comparison of a peptide-containing synthetic lung surfactant with porcine-derived surfactant

    Directory of Open Access Journals (Sweden)

    van Zyl JM

    2013-08-01

    Full Text Available Johann M van Zyl,1 Johan Smith2 1Division of Pharmacology, Department of Medicine, Faculty of Medicine and Health Sciences, Stellenbosch University, Tygerberg, South Africa; 2Department of Paediatrics and Child Health, Tygerberg Children's Hospital, Faculty of Medicine and Health Sciences, Stellenbosch University, Tygerberg, South Africa Background: In a recent study utilizing a saline-lavaged adult rabbit model, we described a significant improvement in systemic oxygenation and pulmonary shunt after the instillation of a novel synthetic peptide-containing surfactant, Synsurf. Respiratory distress syndrome in the preterm lamb more closely resembles that of the human infant, as their blood gas, pH values, and lung mechanics deteriorate dramatically from birth despite ventilator support. Moreover, premature lambs have lungs which are mechanically unstable, with the advantage of being able to measure multiple variables over extended periods. Our objective in this study was to investigate if Synsurf leads to improved systemic oxygenation, lung mechanics, and histology in comparison to the commercially available porcine-derived lung surfactant Curosurf® when administered before first breath in a preterm lamb model. Materials and methods: A Cesarean section was performed under general anesthesia on 18 time-dated pregnant Dohne Merino ewes at 129–130 days gestation. The premature lambs were delivered and ventilated with an expiratory tidal volume of 6–8 mL/kg for the first 30 minutes and thereafter at 8–10 mL/kg. In a randomized controlled trial, the two surfactants tested were Synsurf and Curosurf®, both at a dose of 100 mg/kg phospholipids (1,2-dipalmitoyl-L-α-phosphatidylcholine; 90% in Synsurf, 40% in Curosurf®. A control group of animals was treated with normal saline. Measurements of physiological variables, blood gases, and lung mechanics were made before and after surfactant and saline replacement and at 15, 30, 45, 60, 90, 120, 180

  4. Heterogeneous photocatalytic degradation of phenanthrene in surfactant solution containing TiO{sub 2} particles

    Energy Technology Data Exchange (ETDEWEB)

    Zhang Yanlin, E-mail: zhangyl@scnu.edu.cn [School of Chemistry and Environment, South China Normal University, Guangzhou (China); Sino-Forest Applied Research Centre for Pearl River Delta Environment and Department of Biology, Hong Kong Baptist University, Kowloon Tong (Hong Kong); Wong, J.W.C. [Sino-Forest Applied Research Centre for Pearl River Delta Environment and Department of Biology, Hong Kong Baptist University, Kowloon Tong (Hong Kong); Liu Peihong [School of Chemistry and Environment, South China Normal University, Guangzhou (China); Yuan Min [Research Resources Center, South China Normal University, Guangzhou (China)

    2011-07-15

    Highlights: {yields} Degradation of phenanthrene in surfactant solution and the role of surfactant have been elucidated. {yields} Possible pathway of phenanthrene degradation in surfactant solution is proposed. {yields} The degradation of phenanthrene follows pseudo-second-order kinetics. {yields} It is proved that applying the surfactants as solubilizing agents to remove contaminants from soils followed by photocatalytic degradation is a promising strategy for soil remediation. - Abstract: Photocatalytic degradation of phenanthrene (PHE) over TiO{sub 2} in aqueous solution containing nonionic surfactant micelles was investigated. All photocatalytic experiments were conducted using a 253.7 nm mercury monochromatic ultraviolet lamp in a photocatalytic reactor. The surfactant micelles could provide a nonaqueous 'cage' to result in a higher degradation rate of PHE than in an aqueous solution, but the higher Triton X-100 concentration (more than 2 g/L) lowered the degradation ratio of PHE because the additional surfactant micelles hindered the movement of micelles containing PHE so as to reduce their adsorption onto titania. Pseudo-second-order kinetics was observed for the photocatalytic degradation of PHE. Alkaline solution environment was beneficial to the photocatalytic degradation of PHE. PHE degradation could mainly be attributed to the formation of hydroxyl radicals as evident from the comparison of degradation efficiencies when O{sub 2}, H{sub 2}O{sub 2} and tert-butyl alcohol (TBA) were applied as oxidants or hydroxyl radical scavenger. Based on the GC/MS analysis of the intermediates, the possible pathways of the photocatalytic degradation of PHE were proposed.

  5. Single well surfactant test to evaluate surfactant floods using multi tracer method

    Science.gov (United States)

    Sheely, Clyde Q.

    1979-01-01

    Data useful for evaluating the effectiveness of or designing an enhanced recovery process said process involving mobilizing and moving hydrocarbons through a hydrocarbon bearing subterranean formation from an injection well to a production well by injecting a mobilizing fluid into the injection well, comprising (a) determining hydrocarbon saturation in a volume in the formation near a well bore penetrating formation, (b) injecting sufficient mobilizing fluid to mobilize and move hydrocarbons from a volume in the formation near the well bore, and (c) determining the hydrocarbon saturation in a volume including at least a part of the volume of (b) by an improved single well surfactant method comprising injecting 2 or more slugs of water containing the primary tracer separated by water slugs containing no primary tracer. Alternatively, the plurality of ester tracers can be injected in a single slug said tracers penetrating varying distances into the formation wherein the esters have different partition coefficients and essentially equal reaction times. The single well tracer method employed is disclosed in U.S. Pat. No. 3,623,842. This method designated the single well surfactant test (SWST) is useful for evaluating the effect of surfactant floods, polymer floods, carbon dioxide floods, micellar floods, caustic floods and the like in subterranean formations in much less time and at much reduced cost compared to conventional multiwell pilot tests.

  6. Preparation and Evaluation of Monodisperse Nonionic Surfactants Based on Fluorine-Containing Dicarbamates.

    Science.gov (United States)

    Mureau; Trabelsi; Guittard; Geribaldi

    2000-09-15

    Novel bipodal surfactants of fluorine-containing carbamate type were synthesized with satisfactory yields from the action of fluorinated diisocyanates on oligooxyethylmonomethylated ethers without solvent. The synthetic pathways via malonic intermediates were elaborated in order to use low-price commercially available compounds such as 2-F-alkylethyl iodides and oligooxyethylmonomethylated ethers as starting materials. This new class of nonionic surfactants contains one hydrophobic part and one oleophobic part, and shows peculiar properties due to the presence of two hydrophilic parts (bipodal). All these compounds are monodisperse, i.e, include a perfectly defined number of oxyethylene units. Compared with their bipodal homologues previously described within the F-alkylated series, these new structures were easily obtained from commercial raw materials and are stable against pH media. The evaluation of their behavior at the air-water interface has been studied by measurements of surface tension versus concentration. This allows us to show clearly the variation of the critical micelle concentration (cmc) from 1.1x10(-5) to 9.8x10(-3) mol.l(-1), and of the surface area per surfactant molecule versus studied structures. The dicarbamates of oligooxyethylmonomethylether of 3-(F-alkyl)propyl so realized exhibit noteworthy properties as nonionic fluorinated surfactants. Copyright 2000 Academic Press.

  7. The Collapse of Monolayers Containing Pulmonary Surfactant Phospholipids Is Kinetically Determined

    OpenAIRE

    Yan, Wenfei; Piknova, Barbora; Hall, Stephen B.

    2005-01-01

    Prior studies have shown that during and after slow compressions of monomolecular films containing the complete set of purified phospholipids (PPL) from calf surfactant at an air/water interface, surface pressures (π) reach and sustain values that are remarkably high relative to expectations from simple systems with model lipids. Microscopy shows that the liquid-expanded, tilted-condensed, and collapsed phases are present together in the PPL films between 45 and 65 mN/m. The Gibbs phase rule ...

  8. Heterogeneous photocatalytic degradation of phenanthrene in surfactant solution containing TiO2 particles.

    Science.gov (United States)

    Zhang, Yanlin; Wong, J W C; Liu, Peihong; Yuan, Min

    2011-07-15

    Photocatalytic degradation of phenanthrene (PHE) over TiO(2) in aqueous solution containing nonionic surfactant micelles was investigated. All photocatalytic experiments were conducted using a 253.7 nm mercury monochromatic ultraviolet lamp in a photocatalytic reactor. The surfactant micelles could provide a nonaqueous "cage" to result in a higher degradation rate of PHE than in an aqueous solution, but the higher Triton X-100 concentration (more than 2 g/L) lowered the degradation ratio of PHE because the additional surfactant micelles hindered the movement of micelles containing PHE so as to reduce their adsorption onto titania. Pseudo-second-order kinetics was observed for the photocatalytic degradation of PHE. Alkaline solution environment was beneficial to the photocatalytic degradation of PHE. PHE degradation could mainly be attributed to the formation of hydroxyl radicals as evident from the comparison of degradation efficiencies when O(2), H(2)O(2) and tert-butyl alcohol (TBA) were applied as oxidants or hydroxyl radical scavenger. Based on the GC/MS analysis of the intermediates, the possible pathways of the photocatalytic degradation of PHE were proposed.

  9. Nanoimprint Resist Material Containing Ultraviolet Reactive Fluorine Surfactant for Defect Reduction in Lithographic Fabrication

    Directory of Open Access Journals (Sweden)

    Satoshi Takei

    2012-01-01

    Full Text Available The generated resist based defects on the template in addition to the presence of particles and contaminants is critical for ultraviolet curing of nanoimprint lithographic fabrication. This procedure is proven to be suitable for advanced resist material design under the process conditions. Nanoimprint resist material containing an ultraviolet reactive fluorine surfactant was developed to modify the fundamental surface interactions between resists and the template for defect reduction in nanoimprint patterning replication. The developed acrylate type nanoimprint resist material containing 4,4,5,5,6,6,7,7,8,8,9,9,10,10,11,11,11-heptadecafluoro-2-hydroxyundecyl acrylate as an ultraviolet reactive fluorine surfactant, indicated excellent patterning dimensional accuracy by minimizing surface free energy, and having the effect of improving the generated resist based defect numbers on the template, with a 500 nm contact hole and 2 μm line patterns, in the replication of 20 nanoimprint process cycles. This desirable concept using an ultraviolet reactive fluorine surfactant with an acrylate group in the acrylate type nanoimprint resist material is one of the most promising processes ready to be incorporated into mass fabrication in the next generation of electronic devices.

  10. Synthetic lung surfactants containing SP-B and SP-C peptides plus novel phospholipase-resistant lipids or glycerophospholipids

    Science.gov (United States)

    Notter, Robert H.; Gupta, Rohun; Schwan, Adrian L.; Wang, Zhengdong; Shkoor, Mohanad Gh

    2016-01-01

    Background This study examines the biophysical and preclinical pulmonary activity of synthetic lung surfactants containing novel phospholipase-resistant phosphonolipids or synthetic glycerophospholipids combined with Super Mini-B (S-MB) DATK and/or SP-Css ion-lock 1 peptides that replicate the functional biophysics of surfactant proteins (SP)-B and SP-C. Phospholipase-resistant phosphonolipids used in synthetic surfactants are DEPN-8 and PG-1, molecular analogs of dipalmitoyl phosphatidylcholine (DPPC) and palmitoyl-oleoyl phosphatidylglycerol (POPG), while glycerophospholipids used are active lipid components of native surfactant (DPPC:POPC:POPG 5:3:2 by weight). The objective of the work is to test whether these novel lipid/peptide synthetic surfactants have favorable preclinical activity (biophysical, pulmonary) for therapeutic use in reversing surfactant deficiency or dysfunction in lung disease or injury. Methods Surface activity of synthetic lipid/peptide surfactants was assessed in vitro at 37 °C by measuring adsorption in a stirred subphase apparatus and dynamic surface tension lowering in pulsating and captive bubble surfactometers. Shear viscosity was measured as a function of shear rate on a Wells-Brookfield micro-viscometer. In vivo pulmonary activity was determined by measuring lung function (arterial oxygenation, dynamic lung compliance) in ventilated rats and rabbits with surfactant deficiency/dysfunction induced by saline lavage to lower arterial PO2 to C. However, dual-peptide surfactants containing 1.5% S-MB DATK + 1.5% SP-Css ion-lock 1 combined with 9:1 DEPN-8:PG-1 or 5:3:2 DPPC:POPC:POPG had the greatest in vivo activity in improving arterial oxygenation and dynamic lung compliance in ventilated animals with ARDS. Saline dispersions of these dual-peptide synthetic surfactants were also found to have shear viscosities comparable to or below those of current animal-derived surfactant drugs, supporting their potential ease of deliverability by

  11. Surfactant-Polymer Interaction for Improved Oil Recovery

    Energy Technology Data Exchange (ETDEWEB)

    Gabitto, Jorge; Mohanty, Kishore K.

    2002-01-07

    The goal of this research was to use the interaction between a surfactant and a polymer for efficient displacement of tertiary oil by improving slug integrity, oil solubility in the displacing fluid and mobility control. Surfactant-polymer flooding has been shown to be highly effective in laboratory-scale linear floods. The focus of this proposal is to design an inexpensive surfactant-polymer mixture that can efficiently recover tertiary oil by avoiding surfactant slug degradation and viscous/heterogeneity fingering.

  12. Antioxidant Microemulsion-based Ethylene Vinyl Acetate Film Containing Mangiferin and Surfactants

    Directory of Open Access Journals (Sweden)

    Boonnattakorn Rungkan

    2016-01-01

    Full Text Available Mangiferin, a natural antioxidant additive, was incorporated into an ethylene vinyl acetate copolymer (EVA containing 18% vinyl acetate (VA using the emulsion solvent evaporation technique. Sorbitan ester (Span®20 and polymeric surfactant (Pluronic®P−123 were compared. Mangiferin was finely dispersed in the suspension with the addition of surfactants studied. Span®20 was chosen as the surfactant for film preparation in the next step due to the dispersing and film forming properties. Effects of vinyl acetate (VA contents on the film properties were investigated. The EVA films with 12% VA had the highest tensile strength and oxygen barrier, followed by 18, 25 and 40% VA, respectively. Addition of Span®20 had only a slight effect on mechanical and barrier properties of the films, but markedly increased the release of mangiferin from the EVA matrices except in the 40% VA films. The maximum concentrations of mangiferin released from the 40, 25, 18 and 12% VA films into 95% ethanol were 83.30, 66.84, 51.77 and 34.57 μg·mL−11, respectively. The release concentrations from the 40 and 25% VA films was 2.4 and 1.9 folds of that from the 12% VA film, respectively. The antioxidant activity of the EVA films containing mangiferin and Span®20 was 80% radical-scavenging capacity (RSC for the 40 and 25% VA and 60% RSC for the 18 and 12% VA. The release of mangiferin from the EVA matrices may be controlled by appropriate selection of the surfactants and vinyl acetate contents.

  13. Activity and biophysical inhibition resistance of a novel synthetic lung surfactant containing Super-Mini-B DATK peptide

    Directory of Open Access Journals (Sweden)

    Robert H. Notter

    2016-01-01

    Full Text Available Background/objectives. This study examines the surface activity, resistance to biophysical inhibition, and pulmonary efficacy of a synthetic lung surfactant containing glycerophospholipids combined with Super Mini-B (S-MB DATK, a novel and stable molecular mimic of lung surfactant protein (SP-B. The objective of the work is to test whether S-MB DATK synthetic surfactant has favorable biophysical and physiological activity for future use in treating surfactant deficiency or dysfunction in lung disease or injury.Methods. The structure of S-MB DATK peptide was analyzed by homology modeling and by FTIR spectroscopy. The in vitro surface activity and inhibition resistance of synthetic S-MB DATK surfactant was assessed in the presence and absence of albumin, lysophosphatidylcholine (lyso-PC, and free fatty acids (palmitoleic and oleic acid. Adsorption and dynamic surface tension lowering were measured with a stirred subphase dish apparatus and a pulsating bubble surfactometer (20 cycles/min, 50% area compression, 37 °C. In vivo pulmonary activity of S-MB DATK surfactant was measured in ventilated rabbits with surfactant deficiency/dysfunction induced by repeated lung lavages that resulted in arterial PO2 values <100 mmHg.Results. S-MB DATK surfactant had very high surface activity in all assessments. The preparation adsorbed rapidly to surface pressures of 46–48 mN/m at 37 °C (low equilibrium surface tensions of 22–24 mN/m, and reduced surface tension to <1 mN/m under dynamic compression on the pulsating bubble surfactometer. S-MB DATK surfactant showed a significant ability to resist inhibition by serum albumin, C16:0 lyso-PC, and free fatty acids, but surfactant inhibition was mitigated by increasing surfactant concentration. S-MB DATK synthetic surfactant quickly improved arterial oxygenation and lung compliance after intratracheal instillation to ventilated rabbits with severe surfactant deficiency.Conclusions. S-MB DATK is an active mimic

  14. Synthesis and Monolayer Behaviors of Succinic Acid-Type Gemini Surfactants Containing Semifluoroalkyl Groups.

    Science.gov (United States)

    Kawase, Tokuzo; Nagase, Youhei; Oida, Tatsuo

    2016-01-01

    In this work, novel succinic acid-type gemini surfactants containing semifluoroalkyl groups, dl- and meso-2,3-bis[Rf-(CH2)n]-succinic acids (Rf = C4F9, C6F13, C8F17; n = 2, 9), were successfully synthesized, and the effects of Rf, methylene chain length (n), and stereochemistry on their monolayer behaviors were studied. Critical micelle concentrations (CMC) of dl- and meso-2,3-bis[C4F9(CH2)9]-succinic acids were one order of magnitude smaller than that of the corresponding 1+1 type surfactant, C4F9(CH2)9COOH. From surface pressure-area (π-A) measurements, the lift-off areas of the geminis were found to decrease in the order C4F9 ≥ C6F13 > C8F17, regardless of methylene chain length and stereochemistry. The zero-pressure molecular areas of the geminis were twice those of the corresponding 1+1 type surfactants. Based on Gibbs compression modulus analysis, it was clarified that 2,3-bis[C8F17(CH2)n]-succinic gemini with short methylene chains (n = 2) would form more rigid monolayers than those having long methylene chains (n = 9). Unlike for 2,3-bis(alkyl)-succinic acids, the effects of stereochemistry on the monolayer behavior of semifluoroalkylated geminis were small.

  15. Self-assembly of cationic surfactants that contain thioether groups in the hydrophobic tails.

    Science.gov (United States)

    Lundberg, Dan; Shi, Lei; Menger, Fredric M

    2008-05-06

    Self-assembly in aqueous solutions of cationic surfactants that carry thioether groups in their hydrophobic tails has been investigated. Of particular interest was the identification of possible changes in the aggregate structure due to the presence of sulfur atoms. Solutions of four different compounds [CH(3)CH(2)S(CH(2))(10)N(CH(3))(3)(+)Br(-) (2-10), CH(3)(CH(2))(5)S(CH(2))(6)N(CH(3))(3)(+)Br(-) (6-6), CH(3)(CH(2))(7)S(CH(2))(6)N(CH(3))(3)(+)Br(-) (8-6), and CH(3)(CH(2))(7)S(CH(2))(8)N(CH(3))(3)(+)Br(-) (8-8)] were characterized by (1)H NMR, (13)C NMR, NMR diffusometry, and conductivity measurements. In addition to investigating aqueous solutions containing each of the thioethers present as the sole solute, mixtures of 2-10 or 6-6 with dodecyltrimethylammonium bromide (DTAB) were studied. The addition of a sulfide group to the hydrophobic tail causes an increase in the critical micelle concentration but has a limited effect on the aggregate structure. Micelles are formed at a well-defined concentration for all of the investigated surfactants and surfactant mixtures. However, a comparison of the behavior of concentrated solutions of 8-8 to that of solutions of hexadecyltrimethylammonium bromide (CTAB) of similar concentrations suggests that the presence of a sulfur atom decreases the tendency for micellar growth. This may be a consequence of a slightly higher preference for the micellar surface of a sulfur atom as compared to that of a methylene group in a similar position, an idea that is also supported by results for the surfactant mixtures.

  16. Recovery of Waterflood Residual Oil Using Alkali, Surfactant and Polymer Slugs in Radial Cores Récupération d'huile résiduelle par injection d'eau améliorée de produits alcalins, de tensio-actifs et de polymères dans des carottes radiales

    Directory of Open Access Journals (Sweden)

    Nasr-El-Din H. A.

    2006-11-01

    Full Text Available An experimental study has been conducted to examine mobilization and recovery of waterflood residual oil in radial cores. Alkali, surfactant, and polymer slugs of various compositions, sizes and sequences were tested. Core flood experiments were conducted with unfired radial Berea sandstone disks at a flow rate of 8 cm3/h. David Lloydminster crude oil (total acid number of 0. 45 mg KOH/g oil was used. The results of the present work showed that the composition and sequence of the injected chemical slug play an important role in mobilization and recovery of residual oil. For slugs lacking either mobility control, or low interfacial tension, no oil bank was formed and tertiary oil recovery was less than 20% Sor. A significant oil bank and tertiary oil recovery up to 70 % Sor were obtained with slugs having mobility control and low interfacial tension. However, maximum oil cut, incre-mental oil recovery and surfactant propagation were found to be functions of the alkali content in the slug. The incremental oil recovery, oil cut and slug injectivity greatly improved as the alkali concentration (sodium carbonate in the combined slug was increased. A slight delay in surfactant breakthrough and a significantly slower rate of surfactant propagation were observed at higher sodium carbonate concentrations. Une étude expérimentale ayant pour but d'examiner la mobilisation et la récupération assistée d'huile résiduelle, à la suite d'un déplacement par l'eau en milieu poreux, a été conduite. Des bouchons de produit alcalin, de surfactant et de polymère, ayant des compositions, grosseurs et séquences d'injection variées, furent essayés. Les déplacements en milieu poreux furent conduits en utilisant des carottes de grès berea (non traités à haute température et un débit de 8,0 cm3/h. Pour ce faire, on utilisa de l'huile de David Lloydminster (ayant un nombre acide de 0,45 mg KOH/g d'huile. Les résultats de ce travail ont démontré que la

  17. Novel sample preparation method for surfactant containing suppositories: effect of micelle formation on drug recovery.

    Science.gov (United States)

    Kalmár, Éva; Ueno, Konomi; Forgó, Péter; Szakonyi, Gerda; Dombi, György

    2013-09-01

    Rectal drug delivery is currently at the focus of attention. Surfactants promote drug release from the suppository bases and enhance the formulation properties. The aim of our work was to develop a sample preparation method for HPLC analysis for a suppository base containing 95% hard fat, 2.5% Tween 20 and 2.5% Tween 60. A conventional sample preparation method did not provide successful results as the recovery of the drug failed to fulfil the validation criterion 95-105%. This was caused by the non-ionic surfactants in the suppository base incorporating some of the drug, preventing its release. As guidance for the formulation from an analytical aspect, we suggest a well defined surfactant content based on the turbidimetric determination of the CMC (critical micelle formation concentration) in the applied methanol-water solvent. Our CMC data correlate well with the results of previous studies. As regards the sample preparation procedure, a study was performed of the effects of ionic strength and pH on the drug recovery with the avoidance of degradation of the drug during the procedure. Aminophenazone and paracetamol were used as model drugs. The optimum conditions for drug release from the molten suppository base were found to be 100 mM NaCl, 20-40 mM NaOH and a 30 min ultrasonic treatment of the final sample solution. As these conditions could cause the degradation of the drugs in the solution, this was followed by NMR spectroscopy, and the results indicated that degradation did not take place. The determined CMCs were 0.08 mM for Tween 20, 0.06 mM for Tween 60 and 0.04 mM for a combined Tween 20, Tween 60 system. Copyright © 2013 Elsevier B.V. All rights reserved.

  18. Synthetic lung surfactants containing SP-B and SP-C peptides plus novel phospholipase-resistant lipids or glycerophospholipids

    Directory of Open Access Journals (Sweden)

    Robert H. Notter

    2016-10-01

    Full Text Available Background This study examines the biophysical and preclinical pulmonary activity of synthetic lung surfactants containing novel phospholipase-resistant phosphonolipids or synthetic glycerophospholipids combined with Super Mini-B (S-MB DATK and/or SP-Css ion-lock 1 peptides that replicate the functional biophysics of surfactant proteins (SP-B and SP-C. Phospholipase-resistant phosphonolipids used in synthetic surfactants are DEPN-8 and PG-1, molecular analogs of dipalmitoyl phosphatidylcholine (DPPC and palmitoyl-oleoyl phosphatidylglycerol (POPG, while glycerophospholipids used are active lipid components of native surfactant (DPPC:POPC:POPG 5:3:2 by weight. The objective of the work is to test whether these novel lipid/peptide synthetic surfactants have favorable preclinical activity (biophysical, pulmonary for therapeutic use in reversing surfactant deficiency or dysfunction in lung disease or injury. Methods Surface activity of synthetic lipid/peptide surfactants was assessed in vitro at 37 °C by measuring adsorption in a stirred subphase apparatus and dynamic surface tension lowering in pulsating and captive bubble surfactometers. Shear viscosity was measured as a function of shear rate on a Wells-Brookfield micro-viscometer. In vivo pulmonary activity was determined by measuring lung function (arterial oxygenation, dynamic lung compliance in ventilated rats and rabbits with surfactant deficiency/dysfunction induced by saline lavage to lower arterial PO2 to <100 mmHg, consistent with clinical acute respiratory distress syndrome (ARDS. Results Synthetic surfactants containing 5:3:2 DPPC:POPC:POPG or 9:1 DEPN-8:PG-1 combined with 3% (by wt of S-MB DATK, 3% SP-Css ion-lock 1, or 1.5% each of both peptides all adsorbed rapidly to low equilibrium surface tensions and also reduced surface tension to ≤1 mN/m under dynamic compression at 37 °C. However, dual-peptide surfactants containing 1.5% S-MB DATK + 1.5% SP-Css ion-lock 1 combined with

  19. Oxidored-nitro domain containing protein 1 (NOR1) expression suppresses slug/vimentin but not snail in nasopharyngeal carcinoma: Inhibition of EMT in vitro and in vivo in mice.

    Science.gov (United States)

    Wang, Wei; Li, Xiaoling; Zhang, Wenling; Li, Wenjuan; Yi, Mei; Yang, Jianbo; Zeng, Zhaoyang; Colvin Wanshura, Leah E; McCarthy, James B; Fan, Songqing; Zheng, Pan; Chen, Shengnan; Xiang, Bo; Li, Guiyuan

    2014-06-28

    Oxidored-nitro domain containing protein 1 (NOR1) is a putative tumor suppressor gene. In this study, NOR1 expression was detected in NPC tissues and non-cancerous nasopharyngeal epithelium. The data showed that NOR1 protein was decreased in NPC tissues. Lost expression NOR1 protein was associated with poor overall and event-free survival of NPC patients. Overexpression of NOR1 in NPC cells resulted in a significant morphological change and decreased expression of epithelial-to-mesenchymal transition (EMT) mediators (e.g., slug and vimentin), but induced cytokeratin 13 expression. A nude mouse metastasis assay revealed that overexpression of NOR1 decreased NPC tumor cells metastasis capacity in vivo. Knockdown of NOR1 expression in HeLa cells was sufficient to abrogate epithelial traits and to enhance cell migration and invasion. Concomitant inhibition of slug or vimentin alleviated induction of EMT, migration or invasion by NOR1 siRNA in HeLa cells in vitro. In conclusion, the data from the current study suggest, for the first time, that NOR1 plays an important role in NPC in ex vivo, in vitro, and in vivo. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

  20. A study of surfactant-assisted waterflooding

    Energy Technology Data Exchange (ETDEWEB)

    Scamehorn, J F; Harwell, J H

    1990-09-01

    In surfactant-assisted waterflooding, a surfactant slug is injected into a reservoir, followed by a brine spacer, followed by second surfactant slug. The charge on the surfactant in the first slug has opposite sign to that in the second slug. When the two slugs mix in the reservoir, a precipitate or coacervate is formed which plugs the permeable region of the reservoir. Subsequently injected water or brine is forced through the low permeability region of the reservoir, increasing sweep efficiency of the waterflood, compared to a waterflood not using surfactants. In this part of the work, two major tasks are performed. First, core floods are performed with oil present to demonstrate the improvement in incremental oil production, as well as permeability modification. Second, a reservoir simulation model will be proposed to further delineate the optimum strategy for implementation of the surfactant-assisted waterflooding, as well as indicate the reservoir types for which it would be most effective. Surfactants utilized were sodium dodecyl sulfate and dodecyl pyridinium chloride. 44 refs., 17 figs., 3 tabs.

  1. Diester-containing Zwitterionic Gemini Surfactants with Different Spacer and Its Impact on Micellization Properties and Viscosity of Aqueous Micellar Solution.

    Science.gov (United States)

    Patil, Sachin Vasant; Patil, Sanyukta Arun; Pratap, Amit Prabhakar

    2016-09-01

    A series of diester containing zwitterionic gemini surfactants, N,N-dimethyl-N-alkyl-2-[[hydroxy (alkoxy) phosphinyl]oxy]-alkylammonium designated as C8(-)-S-Cn(+), S = 2 and 3, n = 12, 14 and 16, were synthesized and characterized by instrumental techniques namely FT-IR, (1)H NMR, (13)C NMR, (31)P NMR and Mass spectral studies. These new gemini surfactants further investigated for their various surfactant properties. The critical micelle concentration (cmc) and the effectiveness of surface tension reduction (Πcmc) were determined as a function of surfactant concentration by means of surface tension measurement. Micellization and viscosity properties were investigated by surface tension, electrical conductivity, dye micellization and rheology techniques. The findings of the aqueous surfactant system obtained were impacted by polarity, size and the nature of zwitterions as the surface. The thermodynamic and viscosity properties of these surfactants found to be based on the structures of gemini surfactants.

  2. Carbohydrate-derived surfactants containing an N-Acylated amine functionality : fundamental aspects and practical applications

    NARCIS (Netherlands)

    Pestman, Jolanda Monique

    1998-01-01

    Surfactants (a contraction of the term surface active agents) are large volume chemicals; their annual production exceeds 5 million tons worldwide. They are primarily used as cleaning agents in laundry and dish-washing applications. Surfactants are also applied in cosmetics and pharmaceuticals, in

  3. Carbohydrate-derived surfactants containing an N-Acylated amine functionality : fundamental aspects and practical applications

    NARCIS (Netherlands)

    Pestman, Jolanda Monique

    1998-01-01

    Surfactants (a contraction of the term surface active agents) are large volume chemicals; their annual production exceeds 5 million tons worldwide. They are primarily used as cleaning agents in laundry and dish-washing applications. Surfactants are also applied in cosmetics and pharmaceuticals, in m

  4. Synthesis, surface properties, and biocompatibility of 1,2,3-triazole-containing alkyl β-D-xylopyranoside surfactants.

    Science.gov (United States)

    Oldham, E Davis; Seelam, Srivenu; Lema, Carolina; Aguilera, Renato J; Fiegel, Jennifer; Rankin, Stephen E; Knutson, Barbara L; Lehmler, Hans-Joachim

    2013-09-20

    We are interested in the development of surfactants derived from hemicellulosic biomass, as they are potential components in pharmaceuticals, personal care products, and other detergents. Such surfactants should exhibit low toxicity in mammalian cells. In this study we synthesized a series of alkyl or fluoroalkyl β-xylopyranosides from azides and an alkyne using the copper-catalyzed azide-alkyne (CuAAC) 'click' reaction in 4 steps from xylose. The purified products were evaluated for both their surfactant properties, and for their biocompatibility. Unlike other carbohydrate-based surfactants, liquid-crystalline behavior was not observed by differential scanning calorimetry. The triazole-containing β-xylopyranosides with short (6 carbons) and long (>12 carbons) chains exhibited no toxicity at concentrations ranging from 1 to 1000 μM. Triazole-containing β-xylopyranosides with 8, 10, or 12 carbons caused toxicity via apoptosis, with CC50 values ranging from 26-890 μM. The two longest chain compounds did form stable monolayers at the air-water interface over a range of temperatures, although a brief transition to an the unstable monolayer was observed.

  5. Amphoteric surfactants containing ?-hydroxy ester group and an amino acid residue

    Directory of Open Access Journals (Sweden)

    Eissa, A. M. F.

    2006-09-01

    Full Text Available A series of amphoteric surfactants containing α-hydroxy ester group and an amino acid residue were prepared with the addition of epoxy derivatives (which were prepared from epoxidation of alkyl methacrylate to different types of amino acids (glycine, alanine, valine, isoleucine, phenylalanine, tyrosine, serine, threonine, aspartic and anthranilic acid.The structures of the prepared compounds were confirmed by infrared spectra, proton magnetic resonance spectra, Mass spectra and elementary analysis. Surface tension, Kraft point, foaming power, critical micelle concentration emulsion and Ca++ stabilities were determined. Antimicrobial activity and biodegradability were also screened.Se prepararon una serie de tensioactivos anfóteros conteniendo un grupo alfa hidroxi éster y un residuo de aminoácido por adición de derivados epoxy (obtenidos mediante epoxidación de metacrilato de alquilo a diferentes tipos de aminoácidos (glicina, alanina, valina, isoleucina, fenilalanina, tirosina, serina, treonina y ácidos aspártico y antranílico. Las estructuras de los compuestos preparados se confirmaron por los espectros de infrarrojo, de masa, resonancia magnética nuclear de protones y análisis elemental. Se determinaron la tensión superficial, el punto de Kraft, el poder espumante, la concentración micelar crítica en emulsión y las estabilidades de Ca++. También se estudiaron la actividad antimicrobiana y la biodegradabilidad.

  6. Combined Fenton oxidation and aerobic biological processes for treating a surfactant wastewater containing abundant sulfate.

    Science.gov (United States)

    Wang, Xiao-Jun; Song, Yang; Mai, Jun-Sheng

    2008-12-30

    The present study is to investigate the treatment of a surfactant wastewater containing abundant sulfate by Fenton oxidation and aerobic biological processes. The operating conditions have been optimized. Working at an initial pH value of 8, a Fe2+ dosage of 600mgL(-1) and a H2O2 dosage of 120mgL(-1), the chemical oxidation demand (COD) and linear alkylbenzene sulfonate (LAS) were decreased from 1500 and 490mgL(-1) to 230 and 23mgL(-1) after 40min of Fenton oxidation, respectively. Advanced oxidation pretreatment using Fenton reagent was very effective at enhancing the biodegradability of this kind of wastewater. The wastewater was further treated by a bio-chemical treatment process based on an immobilized biomass reactor with a hydraulic detention time (HRT) of 20h after Fenton oxidation pretreatment under the optimal operating conditions. It was found that the COD and LAS of the final effluent were less than 100 and 5mgL(-1), corresponding to a removal efficiencies of over 94% and 99%, respectively.

  7. Rheological properties of novel viscoelastic micelle systems containing anionic-nonionic dimeric surfactant

    Institute of Scientific and Technical Information of China (English)

    方波; 曹丹红; 江体乾

    2008-01-01

    The viscoelastic micelle systems formed by novel anionic-nonionic dimeric surfactant and conventional cationic surfactant cetyltrimethylammonium(1631) were studied.The viscoelasticity,thixotropy,flow curves and constitutive equation for the novel viscoelastic micelle systems were investigated.The results show that the micelle systems possess viscoelasticity,thixotropy,and shear thinning property.Some micelle systems possess hysteresis loops showing both viscoelasticity and thixotropy.It is proved that the flow curves are characterized by the co-rotational Jeffreys constitutive equation correctly.

  8. Preparation and physicochemical properties of surfactant-free emulsions using electrolytic-reduction ion water containing lithium magnesium sodium silicate.

    Science.gov (United States)

    Okajima, Masahiro; Wada, Yuko; Hosoya, Takashi; Hino, Fumio; Kitahara, Yoshiyasu; Shimokawa, Ken-ichi; Ishii, Fumiyoshi

    2013-04-01

    Surfactant-free emulsions by adding jojoba oil, squalane, olive oil, or glyceryl trioctanoate (medium chain fatty acid triglycerides, MCT) to electrolytic-reduction ion water containing lithium magnesium sodium silicate (GE-100) were prepared, and their physiochemical properties (thixotropy, zeta potential, and mean particle diameter) were evaluated. At an oil concentration of 10%, the zeta potential was ‒22.3 ‒ ‒26.8 mV, showing no marked differences among the emulsions of various types of oil, but the mean particle diameters in the olive oil emulsion (327 nm) and MCT emulsion (295 nm) were smaller than those in the other oil emulsions (452-471 nm). In addition, measurement of the hysteresis loop area of each type of emulsion revealed extremely high thixotropy of the emulsion containing MCT at a low concentration and the olive emulsion. Based on these results, since surfactants and antiseptic agents markedly damage sensitive skin tissue such as that with atopic dermatitis, surfactant- and antiseptic-free emulsions are expected to be new bases for drugs for external use.

  9. Enhanced production of erythritol and mannitol by Yarrowia lipolytica in media containing surfactants.

    Science.gov (United States)

    Rakicka, Magdalena; Rywińska, Anita; Cybulski, Krzysztof; Rymowicz, Waldemar

    2016-01-01

    Various chemical compounds, including surfactants, when introduced to culture media may increase the permeability of cellular membranes and thereby affect the quantity of metabolites excreted by cells. The aim of the present study was to evaluate the impact of detergents including Triton X-100, Span 20 and Tween 80 on erythritol production from glycerol by Yarrowia lipolytica Wratislavia K1 in a shake-flask experiment, batch and fed-batch cultures. When Span 20 was added to a fed-batch culture with glycerol as a carbon source (300gL(-1)), erythritol production increased by 15% compared to the culture without the surfactant where it reached 142gL(-1) after 5 days, which corresponded to 0.47gg(-1) yield and productivity of 1.1gL(-1)h(-1). Therefore, it was concluded that Span 20 considerably enhanced the production of this polyol from glycerol.

  10. Enhanced production of erythritol and mannitol by Yarrowia lipolytica in media containing surfactants

    Directory of Open Access Journals (Sweden)

    Magdalena Rakicka

    2016-06-01

    Full Text Available Abstract Various chemical compounds, including surfactants, when introduced to culture media may increase the permeability of cellular membranes and thereby affect the quantity of metabolites excreted by cells. The aim of the present study was to evaluate the impact of detergents including Triton X-100, Span 20 and Tween 80 on erythritol production from glycerol by Yarrowia lipolytica Wratislavia K1 in a shake-flask experiment, batch and fed-batch cultures. When Span 20 was added to a fed-batch culture with glycerol as a carbon source (300 g L-1, erythritol production increased by 15% compared to the culture without the surfactant where it reached 142 g L-1 after 5 days, which corresponded to 0.47 g g-1 yield and productivity of 1.1 g L-1 h-1. Therefore, it was concluded that Span 20 considerably enhanced the production of this polyol from glycerol.

  11. Compatibilization of HDPE/agar biocomposites with eutectic-based ionic liquid containing surfactant

    OpenAIRE

    Shamsuri, AA; Daik, R; Zainudin, ES; Tahir, PM

    2014-01-01

    In this research, eutectic-based ionic liquid specifically choline chloride/glycerol was prepared at a 1:2 mole ratio. The choline chloride/glycerol was added with the different content of surfactant (hexadecyltrimethylammonium bromide). The choline chloride/glycerol-hexadecyltrimethylammonium bromide was introduced into high-density polyethylene/agar biocomposites through melt mixing. The mechanical testing results indicated that the impact strength and tensile extension of the biocomposites...

  12. Surfactant enhanced recovery of tetrachloroethylene from a porous medium containing low permeability lenses. 1. Experimental studies.

    Science.gov (United States)

    Taylor, T P; Pennell, K D; Abriola, L M; Dane, J H

    2001-04-01

    A matrix of batch, column and two-dimensional (2-D) box experiments was conducted to investigate the coupled effects of rate-limited solubilization and layering on the entrapment and subsequent recovery of a representative dense NAPL, tetrachloroethylene (PCE), during surfactant flushing. Batch experiments were performed to determine the equilibrium solubilization capacity of the surfactant, polyoxyethylene (20) sorbitan monooleate (Tween 80), and to measure fluid viscosity, density and interfacial tension. Results of one-dimensional column studies indicated that micellar solubilization of residual PCE was rate-limited at Darcy velocities ranging from 0.8 to 8.2 cm/h and during periods of flow interruption. Effluent concentration data were used to develop effective mass transfer coefficient (Ke) expressions that were dependent upon the Darcy velocity and duration of flow interruption. To simulate subsurface heterogeneity, 2-D boxes were packed with layers of F-70 Ottawa sand and Wurtsmith aquifer material within 20-30 mesh Ottawa sand. A 4% Tween 80 solution was then flushed through PCE-contaminated boxes at several flow velocities, with periods of flow interruption. Effluent concentration data and visual observations indicated that both rate-limited solubilization and pooling of PCE above the fine layers reduced PCE recovery to levels below those anticipated from batch and column measurements. These experimental results demonstrate the potential impact of both mass transfer limitations and subsurface layering on the recovery of PCE during surfactant enhanced aquifer remediation.

  13. Wetting Resistance of Commercial Membrane Distillation Membranes in Waste Streams Containing Surfactants and Oil

    Directory of Open Access Journals (Sweden)

    Lies Eykens

    2017-01-01

    Full Text Available Water management is becoming increasingly challenging and several technologies, including membrane distillation (MD are emerging. This technology is less affected by salinity compared to reverse osmosis and is able to treat brines up to saturation. The focus of MD research recently shifted from seawater desalination to industrial applications out of the scope of reverse osmosis. In many of these applications, surfactants or oil traces are present in the feed stream, lowering the surface tension and increasing the risk for membrane wetting. In this study, the technological boundaries of MD in the presence of surfactants are investigated using surface tension, contact angle and liquid entry pressure measurements together with lab-scale MD experiments to predict the wetting resistance of different membranes. Synthetic NaCl solutions mixed with sodium dodecyl sulfate (SDS were used as feed solution. The limiting surfactant concentration was found to be dependent on the surface chemistry of the membrane, and increased with increasing hydrophobicity and oleophobicity. Additionally, a hexadecane/SDS emulsion was prepared with a composition simulating produced water, a waste stream in the oil and gas sector. When hexadecane is present in the emulsion, oleophobic membranes are able to resist wetting, whereas polytetrafluoretheen (PTFE is gradually wetted by the feed liquid.

  14. Rheological behavior of aqueous dispersions containing blends of rhamsan and welan polysaccharides with an eco-friendly surfactant.

    Science.gov (United States)

    Trujillo-Cayado, L A; Alfaro, M C; Raymundo, A; Sousa, I; Muñoz, J

    2016-09-01

    Small amplitude oscillatory shear and steady shear flow properties of rhamsan gum and welan gum dispersions containing an eco-friendly surfactant (a polyoxyethylene glycerol ester) formulated to mimic the continuous phase of O/W emulsions were studied using the surface response methodology. A second order polynomial equation fitted the influence of surfactant concentration, rhamsan/welan mass ratio and total concentration of polysaccharides. Systems containing blends of rhamsan and welan did not show synergism but thermodynamic incompatibility and made it possible to adjust the linear viscoelastic and low shear rate flow properties to achieve values in between those of systems containing either rhamsan or welan as the only polysaccharide. All the systems studied exhibited weak gel rheological properties as the mechanical spectra displayed the plateau or rubber-like relaxation zone, the linear viscoelastic range was rather narrow and flow curves presented shear thinning behavior, which fitted the power-law equation. While mechanical spectra of the systems studied demonstrated that they did not control the linear viscoelastic properties of the corresponding emulsions, the blend of rhamsan and welan gums was able to control the steady shear flow properties.

  15. Characterization of SLUG microwave amplifiers

    Science.gov (United States)

    Hoi, I.-C.; Zhu, S.; Thorbeck, T.; McDermott, R.; Mutus, J.; Jeffrey, E.; Barends, R.; Chen, Y.; Roushan, P.; Fowler, A.; Sank, D.; White, T.; Campbell, B.; Chen, Z.; Chiaro, B.; Dunsworth, A.; Kelly, J.; Megrant, A.; Neill, C.; O'Malley, P. J. J.; Quintana, C.; Vainsencher, A.; Wenner, J.; Martinis, J. M.

    2015-03-01

    With the rapid growth of superconducting circuits quantum technology, a near quantum-limited amplifier at GHz frequency is needed to enable high fidelity measurements. We describe such an amplifier, the SQUID based, superconducting low inductance undulatory galvanometer (SLUG) amplifier. We measure the full scattering matrix of the SLUG. In particular, we measure both forward and reverse gain, as well as reflection. We see 15dB forward gain with added noise from one quanta to several quanta. The -1 dB compression point is around -95 dBm, about two orders of magnitude higher than that of typical Josephson parametric amplifiers. With these properties, SLUG is well suited for the high fidelity, simultaneous multiplexed readout of superconducting qubits.

  16. Evaluation of waste activated sludge as a coagulant aid for the treatment of industrial wastewater containing mixed surfactants.

    Science.gov (United States)

    Sriwiriyarat, Tongchai; Jangkorn, Siriprapha

    2009-04-01

    Wastewater generated by the industry manufacturing detergents and various kinds of consumer products normally contains very high contents of mixed surfactants, organic matters expressed as chemical oxygen demand (COD), and phosphates that must be treated prior to discharge to the aquatic environment. In this study, jar-test experiments were conducted to evaluate the waste activated sludge (WAS) as a coagulation aid in the coagulation-flocculation process with ferric chloride or aluminum sulfate as a coagulant for the treatment of wastewater collected from the aforementioned industry. The WAS was selected because of its adsorption capability of anionic surfactants and its availability from the wastage stream of biological wastewater treatment process. The effective dosages of both coagulants with and without the WAS additions were determined in this study. Without the WAS addition, the concentrations of 800 mg/L aluminum sulfate at the optimum pH value of 8 and 2208 mg/L ferric chloride at the optimum pH value of 12 were the optimum chemical dosages. It appears that aluminum sulfate was more effective than ferric chloride based on the chemical dosage and removal efficiency. The turbidity, suspended particles, anionic surfactants, COD, and phosphates removal efficiencies of aluminum sulfate and ferric chloride under the optimum dosage were 95.6, 88.2, 78.4, 73.5, 47.3% and 98.8, 92.0, 72.7, 67.5, 53.1%, respectively. The addition of 200 mg/L WAS was sufficient to reduce the optimum dosages of both chemicals by 200 mg/L. The cationic surfactant existing in the wastewater worked as a flocculating agent leading to the flocculation of waste activated sludge resulting in the enmeshment of the suspended particles and colloids on which the COD, anionic surfactants, and phosphates were adsorbed. However, the substances removal efficiencies of ferric chloride and aluminum sulfate were slightly enhanced and reduced, respectively. It is possibly explained that the settling time

  17. In vitro and in vivo evaluation of Bola-surfactant containing niosomes for transdermal delivery.

    Science.gov (United States)

    Paolino, Donatella; Muzzalupo, Rita; Ricciardi, Antonio; Celia, Christian; Picci, Nevio; Fresta, Massimo

    2007-08-01

    A novel niosome formulation is proposed for topical drug delivery of ammonium glycyrrhizinate, a natural compound with an efficacious anti-inflammatory activity. Niosomes were made up of a new non ionic surfactant, alpha,omega-hexadecyl-bis-(1-aza-18-crown-6) (Bola-surfactant)-Span 80-cholesterol (2:3:1 molar ratio). Niosome vesicles were prepared with the thin layer evaporation method and were physico-chemically characterized. The tolerability of Bola-surfactant both as free molecules or assembled ion niosome vesicles was evaluated in vitro on cultured of human keratinocyte cells (NCTC2544). Human tolerability was evaluated on volunteers. The ability of Bola-niosomes to promote intracellular delivery was evaluated by confocal laser scanning microscopy (CLSM) studies. Human stratum corneum and epidermis (SCE) membranes were used in vitro to investigate the percutaneous permeation. The anti-inflammatory activity of ammonium glycyrrhizinate was evaluated in vivo on human volunteers with a chemically induced erythema. Experimental data show that Bola-niosomes are characterized by a mean size of approximately 400 nm and are able to provide an encapsulation efficiency of 40% with respect to the drug amount used during preparation. CLSM showed that Bola-niosomes were able to promote the intracellular uptake of the delivered substances. Bola-niosomes were also able to significantly improve (pBola-niosomes and the aqueous drug solution. Bola-niosomes showed a suitable tolerability both in vitro and in vivo. Ammonium glycyrrhizinate-loaded Bola-niosomes determined a significant (p<0.001) and noticeable improvement of the in vivo anti-inflammatory activity of the drug. An effective example of conjugating innovative colloidal carriers, coming from pharmaceutical nanotechnology, and therapeutically effective natural compounds, coming from traditional medicine, was reported.

  18. Evaluation of reusing alum sludge for the coagulation of industrial wastewater containing mixed anionic surfactants.

    Science.gov (United States)

    Jangkorn, Siriprapha; Kuhakaew, Sinchai; Theantanoo, Suwapee; Klinla-or, Harit; Sriwiriyarat, Tongchai

    2011-01-01

    A coagulation-flocculation process is typically employed to treat the industrial wastewater generated by the consumer products industry manufacturing detergents, soaps, and others. The expenditure of chemicals including coagulants and chemicals for pH adjustment is costly for treating this wastewater. The objective of this study was to evaluate the feasibility of reusing the aluminum sulfate (alum) sludge as a coagulant or as a coagulation aid so that the fresh alum dosage can be minimized or the removal efficiency can be enhanced. The experiments were conducted in a jar-test apparatus simulating the coagulation-flocculation process for simultaneous removals of organic matters, anionic surfactants, suspended solids, and turbidity. At the optimum initial pH value of 10 and the fresh alum concentration of 400 mg/L, the total suspended solids (TSS), total chemical oxygen demand (TCOD), total anionic surfactants, and turbidity removal efficiencies were 71.5%, 76.4%, 95.4%, and 98.2%, respectively. The addition of alum sludge as a coagulant alone without any fresh alum addition could significantly remove the turbidity, TCOD, and anionic surfactants. The TSS was left in the supernatants after the settling period, but would subsequently be removed by adding the fresh alum. The TSS, TCOD, and turbidity removal efficiencies were also enhanced when both the alum sludge and the fresh alum were employed. The TCOD removal efficiency over 80% has been accomplished, which has never fulfilled by using the fresh alum alone. It is concluded that the alum sludge could be reused for the treatment of industrial wastewater generated by the consumer products industry.

  19. Evaluation of reusing alum sludge for the coagulation of industrial wastewater containing mixed anionic surfactants

    Institute of Scientific and Technical Information of China (English)

    Siriprapha Jangkorn; Sinchai Kuhakaew; Suwapee Theantanoo; Harit Klinla-or; Tongchai Sriwiriyarat

    2011-01-01

    A coagulation-flocculation process is typically employed to treat the industrial wastewater generated by the consumer products industry manufacturing detergents, soaps, and others. The expenditure of chemicals including coagulants and chemicals for pH adjustment is costly for treating this wastewater. The objective of this study was to evaluate the feasibility of reusing the aluminum sulfate (alum) sludge as a coagulant or as a coagulation aid so that the fresh alum dosage can be minimized or the removal efficiency can be enhanced. The experiments were conducted in a jar-test apparatus simulating the coagulation-fiocculation process for simultaneous removals of organic matters, anionic surfactants, suspended solids, and turbidity. At the optimum initial pH value of 10 and the fresh alum concentration of 400 mg/L, the total suspended solids (TSS), total chemical oxygen demand (TCOD), total anionic surfactants,and turbidity removal efficiencies were 71.5%, 76.4%, 95.4%, and 98.2%, respectively. The addition of alum sludge as a coagulant alone without any fresh alum addition could significantly remove the turbidity, TCOD, and anionic surfactants. The TSS was left in the supernatants after the settling period, but would subsequently be removed by adding the fresh alum. The TSS, TCOD, and turbidity removal efficiencies were also enhanced when both the alum sludge and the fresh alum were employed. The TCOD removal efficiency over 80% has been accomplished, which has never fulfilled by using the fresh alum alone. It is concluded that the alum sludge could be reused for the treatment of industrial wastewater generated by the consumer products industry.

  20. Small-angle neutron scattering from mixtures of sodium dodecyl sulfate and a cationic, bolaform surfactant containing azobenzene.

    Science.gov (United States)

    Hubbard, F Pierce; Santonicola, Gabriella; Kaler, Eric W; Abbott, Nicholas L

    2005-07-05

    This paper reports on the microstructures formed in aqueous solutions containing mixtures of sodium dodecyl sulfate (SDS) and a photosensitive, bolaform surfactant, bis(trimethylammoniumhexyloxy)azobenzene dibromide (BTHA). By using quasi-elastic light scattering and small-angle neutron scattering, we determined that aqueous solutions containing SDS and the trans isomer of BTHA (0.1 wt % total surfactant, 15 mol % BTHA, 85 mol % SDS) form vesicles with average hydrodynamic diameters of 1350 +/- 50 angstroms and bilayer thicknesses of 35 +/- 2 angstroms. The measured bilayer thickness is consistent with a model of the vesicle bilayer in which the trans isomer of BTHA spans the bilayer. Upon illumination with UV light, the BTHA underwent photoisomerization to produce a cis-rich photostationary state (80% cis isomer). We measured this photoisomerization to drive the reorganization of vesicles into cylindrical aggregates with cross-sectional radii of 19 +/- 3 angstroms and average hydrodynamic diameters of 240 +/- 50 angstroms. Equilibration of the cis-rich solution in the dark at 25 degrees C for 12 h or illumination of the solution with visible light leads to the recovery of the trans-rich photostationary state of the solution and the reformation of vesicles, thus demonstrating the potential utility of this system as the basis of a tunable fluid.

  1. NUMERICAL SIMULATION AND FIELD IMPLEMENTATION OF SURFACTANT FLOODING

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Based on the features of surfactant flooding, a mathematical model for surfactant flooding is established. The adsorption-retention, convection diffusion of surfactant and influence of concentration change upon relative permeability curve are included in the model. The novel description of adsorption quantity of surfactant and relative permeability curve are presented, which enhance the coincidence between mathematical model and field practice, the relative errors of main development indexes are within 6%. The model is applied to the numerical research of the surfactant flooding in the untabulated beds of Xing1-3 surfactant flooding pilot site of No.4 Oil Production Company of Daqing Oilfield, the influences of surfactant concentration, injection quantity, slug combination mode upon the development effect and economic benefit are quantitatively analyzed, the injection scheme is optimized as follows: surfactant concentration is 0.5%, slug volume is 0.02 PV, slug combination mode is 2 slugs. After the implementation of scheme in oilfield, the cumulative increase of oil is 2186.0 t, up to nearly 30%.

  2. Fabrication of rare-earth bearing fuel slug by injection casting method

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jong Hwan; Song, Hoon; Kim, Hyung Tae; Kim, Ki Hwan; Lee, Chan Bock [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-05-15

    Herein, U.10wt%Zr fuel slugs containing 0, 3, and 7 wt%RE were prepared by an injection casting method and their characteristics were evaluated. The as-cast fuel slugs were generally sound and fabricated to the full length of the mold. However, the increased amount of the charged RE noticeably deteriorated the quality of the casting components such as melting crucible. Chemical analysis of the U.10Zr and U.10Zr.3RE slugs showed that the target composition was matched to within 1.0 wt%. In contrast, the composition of the U.10Zr.7RE fuel slug differed by as much as 4.6 wt% from the target. Therefore, more protective casting variables should be considered, when casting high RE-bearing fuel slugs. KAERI seeks to develop and demonstrate the technologies needed to transmute the long-lived transuranic actinide isotopes in spent nuclear fuel into shorter-lived fission products.

  3. Thermally cleavable surfactants

    Science.gov (United States)

    McElhanon, James R.; Simmons, Blake A.; Zifer, Thomas; Jamison, Gregory M.; Loy, Douglas A.; Rahimian, Kamyar; Long, Timothy M.; Wheeler, David R.; Staiger, Chad L.

    2006-04-04

    Two new surfactant molecules are reported which contain thermally labile Diels-Alder adducts connecting the polar and non-polar sections of each molecule. The two surfactants possess identical non-polar dodecyl tail segments but exhibit different polar headgroups. The surfactants become soluble in water when anionic salts are formed through the deprotonation of the surfactant headgroups by the addition of potassium hydroxide. When either surfactant is exposed to temperature above about 60.degree. C., the retro Diels-Alder reaction occurs, yielding hydrophilic and hydrophobic fragments and the aqueous solutions of the surfactants subsequently exhibit loss of all surface-active behavior.

  4. Thermally cleavable surfactants

    Energy Technology Data Exchange (ETDEWEB)

    McElhanon, James R. (Manteca, CA); Simmons, Blake A. (San Francisco, CA); Zifer, Thomas (Manteca, CA); Jamison, Gregory M. (Albuquerque, NM); Loy, Douglas A. (Albuquerque, NM); Rahimian, Kamyar (Albuquerque, NM); Long, Timothy M. (Urbana, IL); Wheeler, David R. (Albuquerque, NM); Staiger, Chad L. (Albuquerque, NM)

    2009-09-29

    Two new surfactant molecules are reported which contain thermally labile Diels-Alder adducts connecting the polar and non-polar sections of each molecule. The two surfactants possess identical non-polar dodecyl tail segments but exhibit different polar headgroups. The surfactants become soluble in water when anionic salts are formed through the deprotonation of the surfactant headgroups by the addition of potassium hydroxide. When either surfactant is exposed to temperature above about 60.degree. C., the retro Diels-Alder reaction occurs, yielding hydrophilic and hydrophobic fragments or the aqueous solutions of the surfactants subsequently exhibit loss of all surface-active behavior.

  5. Thermally cleavable surfactants

    Energy Technology Data Exchange (ETDEWEB)

    McElhanon, James R. (Manteca, CA); Simmons, Blake A. (San Francisco, CA); Zifer, Thomas (Manteca, CA); Jamison, Gregory M. (Albuquerque, NM); Loy, Douglas A. (Albuquerque, NM); Rahimian, Kamyar (Albuquerque, NM); Long, Timothy M. (Urbana, IL); Wheeler, David R. (Albuquerque, NM); Staiger, Chad L. (Albuquerque, NM)

    2009-11-24

    Two new surfactant molecules are reported which contain thermally labile Diels-Alder adducts connecting the polar and non-polar sections of each molecule. The two surfactants possess identical non-polar dodecyl tail segments but exhibit different polar headgroups. The surfactants become soluble in water when anionic salts are formed through the deprotonation of the surfactant headgroups by the addition of potassium hydroxide. When either surfactant is exposed to temperature above about 60.degree. C., the retro Diels-Alder reaction occurs, yielding hydrophilic and hydrophobic fragments or the aqueous solutions of the surfactants subsequently exhibit loss of all surface-active behavior.

  6. Compatibilization of HDPE/agar biocomposites with eutectic-based ionic liquid containing surfactant

    CERN Document Server

    Shamsuri, AA; Zainudin, ES; Tahir, PM

    2014-01-01

    In this research, eutectic-based ionic liquid specifically choline chloride/glycerol was prepared at a 1:2 mole ratio. The choline chloride/glycerol was added with the different content of surfactant (hexadecyltrimethylammonium bromide). The choline chloride/glycerol-hexadecyltrimethylammonium bromide was introduced into high-density polyethylene/agar biocomposites through melt mixing. The mechanical testing results indicated that the impact strength and tensile extension of the biocomposites increased with the introduction of the choline chloride/glycerol-hexadecyltrimethylammonium bromide. The scanning electron microscope, differential scanning calorimetry and thermal gravimetric analysis results exhibited that significant decrease in the number of agar fillers pull-out, melting point and thermal decomposition temperatures of the biocomposites are also due to the choline chloride/glycerol-hexadecyltrimethylammonium bromide. The Fourier transform infrared spectra and X-ray diffractometer patterns of the bioc...

  7. Use of mixtures containing nonionic surfactants in the destabilization of petroleum emulsions

    Energy Technology Data Exchange (ETDEWEB)

    Mansur, Claudia R.E.; Mauro, Aparecida C.; Aquino, Aline S.; Lechuga, Fernanda C.; Gonzalez, Gaspar; Lucas, Elizabete F. [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Inst. de Macromoleculas; Gonzalez, Gaspar [PETROBRAS, Rio de Janeiro, RJ (Brazil). Centro de Pesquisas (CENPES)

    2004-07-01

    During the petroleum dehydration process, it is necessary to used chemical demulsifiers in order to break the w/o emulsions that are formed in the oil field. These demulsifiers products are, in many cases, surfactants based poly(ethylene oxide-propylene oxide) block copolymers (PEO-PPO), with different EO/PO molar ratio. In this work were correlate the structure and the properties of PEO-PPO block copolymers with their performance as petroleum emulsion-destabilizing agent. Moreover, it was used an additive in the formulations, known as hydrotrope, in order to increase the solubility of these copolymers in aqueous solution. The results showed that the copolymer branched, whose hydrophilic segments (PEO and OH) are in an external adjacent position, present the higher solubility, in spite of to own EO/PO ratio similar to the others copolymers and the highest molar mass. Moreover, this copolymer presented the best efficiency in the emulsion destabilization. The addition of the hydrotrope NaBMGS to the PEO-PPO copolymers aqueous solutions caused the solubility increasing of these compounds in water. Such additive being used in the demulsifier formulation provoked an efficiency improving on the emulsion breaking process. (author)

  8. Stability studies of silymarin nanoemulsion containing Tween 80 as a surfactant

    Directory of Open Access Journals (Sweden)

    Rabea Parveen

    2015-01-01

    Full Text Available Background: Silymarin, a flavonolignan from "milk thistle" (Silybum marianum plant is used almost exclusively for hepatoprotection. Because of its low bioavailability, it was incorporated into a nanoemulsion formulation. The aim of the present study was to check the stability of silymarin nanoemulsion at different temperatures for 3 months. Materials and Methods: The oil-in-water based nanoemulsion formulation was prepared by titration method. Silymarin nanoemulsion was characterized by droplet size, viscosity, and refractive index. Droplet size, viscosity, and refractive index were determined every month. The shelf-life of silymarin nanoemulsion was determined by accelerated stability testing. Results: It was found that there was no significant change in the droplet size, viscosity, and refractive index at refrigerator and room temperature during the period of 3 months. The half-life of the optimized nanoemulsion formulation was found to be 4.74 years at room temperature. Conclusion: These results indicated that stability of silymarin can be enhanced in nanoemulsion formulation using Tween 80 as a surfactant.

  9. Comparison between the removal of phenol and catechol by modified montmorillonite with two novel hydroxyl-containing Gemini surfactants

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Yuening; Gao, Manglai, E-mail: mlgao@cup.edu.cn; Gu, Zheng; Luo, Zhongxin; Ye, Yage; Lu, Laifu

    2014-02-01

    Highlights: • Organo-clays were prepared by two novel hydroxyl-containing Gemini surfactants. • The kinetics and thermodynamics of the novel organo-clays were studied. • The hydroxyl group of organo-clays can increase the adsorption capacity. • BHHP-Mt was proved to be a high-efficiency adsorbent to remove phenols. - Abstract: Na-montmorillonites were modified with two novel hydroxyl-containing Gemini surfactants, 1,3-bis(hexadecyldimethylammonio)-2-hydroxypropane dichloride (BHHP) and 1,3-bis(octyldimethylammonio)-2-hydroxypropane dichloride (BOHP), via ion-exchange reaction in this study. The modified samples were characterized by X-ray diffraction (XRD) and Fourier Transform Infrared (FT-IR) spectroscopy. Phenol and catechol were removed from aqueous solution by these two kinds of organo-montmorillonites in a batch system. Important parameters have been investigated, which affect the adsorption efficiency, such as the amount of modifier, temperature, pH and contact time. The adsorption kinetics of phenol and catechol were discussed using pseudo-first-order, pseudo-second-order and intra-particle diffusion model. It indicated that the experimental data fitted very well with the pseudo-second-order kinetic model, and the equilibrium adsorption data was proved in good agreement with the Langmuir isotherm. The result also showed the adsorption capacity of catechol was higher than that of phenol in the same conditions, which might result from the extra hydroxyl in the structure of catechol. Thermodynamic quantities such as Gibbs free energy (ΔG°), the enthalpy (ΔH°), and the entropy change of sorption (ΔS°) were also determined. These parameters suggested the adsorption of phenol was a spontaneous and exothermic process, while the sorption of catechol was endothermic.

  10. High-resolution slug testing.

    Science.gov (United States)

    Zemansky, G M; McElwee, C D

    2005-01-01

    The hydraulic conductivity (K) variation has important ramifications for ground water flow and the transport of contaminants in ground water. The delineation of the nature of that variation can be critical to complete characterization of a site and the planning of effective and efficient remedial measures. Site-specific features (such as high-conductivity zones) need to be quantified. Our alluvial field site in the Kansas River valley exhibits spatial variability, very high conductivities, and nonlinear behavior for slug tests in the sand and gravel aquifer. High-resolution, multilevel slug tests have been performed in a number of wells that are fully screened. A general nonlinear model based on the Navier-Stokes equation, nonlinear frictional loss, non-Darcian flow, acceleration effects, radius changes in the wellbore, and a Hvorslev model for the aquifer has been used to analyze the data, employing an automated processing system that runs within the Excel spreadsheet program. It is concluded that slug tests can provide the necessary data to identify the nature of both horizontal and vertical K variation in an aquifer and that improved delineation or higher resolution of K structure is possible with shorter test intervals. The gradation into zones of higher conductivity is sharper than seen previously, and the maximum conductivity observed is greater than previously measured. However, data from this project indicate that well development, the presence of fines, and the antecedent history of the well are important interrelated factors in regard to slug-test response and can prevent obtaining consistent results in some cases.

  11. Enhanced oil recovery by surfactant-enhanced volumetric sweep efficiency: First annual report for the period September 30, 1985-September 30, 1986. [Sandpacks

    Energy Technology Data Exchange (ETDEWEB)

    Harwell, J H; Scamehorn, J F

    1987-05-01

    Surfactant-enhanced volumetric sweep efficiency is a novel EOR method which utilizes precipitation/coacervation of surfactants to plug the most permeable regions of the reservoir, improving the efficiency of a waterflooding operation. This technique does not rely on reduction of interfacial tension between aqueous and oleic phases to enhance oil recovery. Therefore, even though surfactants are involved, this new technique is not a substitute or improvement on classical surfactant flooding; however, it has the potantial to compete with polymer flooding as an alternative sweep efficiency improvement method. In surfactant-enhanced volumetric sweep efficiency, a slug containing one kind of surfactant is injected into the reservoir, followed by a brine spacer. This is followed by injection of a second kind of surfactant which has lower adsorption than the first surfactant used. Anionic and cationic surfactants are one possible combination for this application. These may form either a precipitate or a coacervate upon mixing. Phase boundaries for some specific systems of this type have been determined over a wide range of conditions and a model developed to describe this behavior. Another possibility is the use of nonionic surfactants, which may form coacervate under proper conditions. The adsorption behavior of mixtures of anionic and nonionic surfactants was measured to aid in modeling the chromatographic effects with these surfactants in the reservoir. Studies with sandpacks of different permeabilities in parallel configuration using mixtures of anionic and cationic surfactants have demonstrated the capability of this method to reduce flow rates through a more permeable sandpack more than that through a less permeable sandpack. 4 refs., 23 figs., 8 tabs.

  12. The role of surfactants in the formulation of elastic liposomal gels containing a synthetic opioid analgesic

    Directory of Open Access Journals (Sweden)

    Singh S

    2016-04-01

    Full Text Available Sima Singh,1,* Harsh Vardhan,1,* Niranjan G Kotla,2 Balaji Maddiboyina,3 Dinesh Sharma,4 Thomas J Webster5,6 1School of Pharmaceutical Sciences, Lovely Professional University, Phagwara, India; 2Center for Research in Medical Devices, National University of Ireland, Galway, Ireland; 3Department of Pharmaceutics, Vishwabharathi College of Pharmaceutical Sciences, Guntur, India; 4Ranbaxy Laboratory Ltd, Gurgaon, India; 5Department of Chemical Engineering, Northeastern University, Boston, MA, USA; 6Center of Excellence for Advanced Materials Research, King Abdulaziz University, Jeddah, Saudi Arabia *These authors contributed equally to this work Abstract: Transdermal drug delivery systems have made significant contributions to the medical community, but have yet to completely substitute oral or parenteral delivery. Recently, various strategies have been used to augment the transdermal delivery of therapeutics. Primarily, they include iontophoresis, electrophoresis, sonophoresis, chemical permeation enhancers, microneedles, and vesicular systems. Among these strategies, elastic liposomes appear promising. Elastic vesicle scaffolds have been developed and evaluated as novel topical and transdermal delivery systems, with an infrastructure consisting of hydrophobic and hydrophilic moieties together, and as a result, such scaffolds can accommodate drug molecules with a wide range of solubility. High deformability of these vesicles provides for better penetration of intact vesicles. This system is much more efficient at delivering low- and high-molecular-weight drugs to the skin in terms of quantity and depth. In this work, elastic liposomes of Tramadol HCl were prepared using a solvent evaporation method with different surfactants and were characterized using microscopy, and particle size, shape, drug content, ex vivo release, and zeta potential were also calculated. The prepared elastic liposomes were found to be in the range of 152.4 nm with a zeta

  13. Synthesis and Solution Properties of Adamantane Containing Quaternary Ammonium Salt-type Cationic Surfactants: Hydrocarbon-based, Fluorocarbonbased and Bola-type.

    Science.gov (United States)

    Yoshimura, Tomokazu; Okada, Mari; Matsuoka, Keisuke

    2016-10-01

    Quaternary ammonium salt-type cationic surfactants with an adamantyl group (hydrocarbon-type; CnAdAB, fluorocarbon-type; Cm(F)C3AdAB, bola-type; Ad-s-Ad, where n, m and s represent hydrocarbon chain lengths of 8-16, fluorocarbon chain lengths of 4-8, and spacer chain length of 10-12) were synthesized via quaternization of N, N-dimethylaminoadamantane and n-alkyl bromide or 1, n-dibromoalkane. Conductivity and surface tension were measured to characterize the solution properties of the synthesized adamantyl group-containing cationic surfactants. In addition, the effects of hydrocarbon and fluorocarbon chain lengths and spacer chain length between headgroups on the measured properties were evaluated by comparison with those of conventional cationic surfactants. The critical micelle concentration (CMC) of CnAdAB and Ad-s-Ad was 2/5 of that for the corresponding conventional surfactants CnTAB and bola-type surfactants with similar number of carbons in the alkyl or alkylene chain; this was because of the increased hydrophobicity due to the adamantyl group. A linear relationship between the logarithm of CMC and the hydrocarbon chain length for CnAdAB was observed, as well as for CnTAB. The slope of the linear correlation for both surfactants was almost the same, indicating that the adamantyl group does not affect the CMC with variations in the hydrocarbon chain length. Similar to conventional surfactants CnTAB, the hydrocarbon-type CnAdAB is highly efficient in reducing the surface tension of water, despite the large occupied area per molecule resulting from the relatively bulky structure of the adamantane skeleton. On the other hand, the bola-type Ad-s-Ad resulted in increased surface tension compared to CnAdAB, indicating that the curved chain between adamantyl groups leads to poor adsorption and orientation at the air-water interface.

  14. Effects of surfactants on the properties of mortar containing styrene/methacrylate superplasticizer.

    Science.gov (United States)

    Negim, El-Sayed; Kozhamzharova, Latipa; Khatib, Jamal; Bekbayeva, Lyazzat; Williams, Craig

    2014-01-01

    The physical and mechanical properties of mortar containing synthetic cosurfactants as air entraining agent are investigated. The cosurfactants consist of a combination of 2% dodecyl benzene sodium sulfonate (DBSS) and either 1.5% polyvinyl alcohol (PVA) or 1.5% polyoxyethylene glycol monomethyl ether (POE). Also these cosurfactants were used to prepare copolymers latex: styrene/butyl methacrylate (St/BuMA), styrene/methyl methacrylate (St/MMA), and styrene/glycidyl methacrylate (St/GMA), in order to study their effects on the properties of mortar. The properties of mortar examined included flow table, W/C ratio, setting time, water absorption, compressive strength, and combined water. The results indicate that the latex causes improvement in mortar properties compared with cosurfactants. Also polymer latex containing DBSS/POE is more effective than that containing DBSS/PVA.

  15. Photoregulated potassium ion permeation through dihexadecyl phosphate bilayers containing azobenzene and stilbene surfactants

    Energy Technology Data Exchange (ETDEWEB)

    Lei, Y.; Hurst, J.K. [Washington State Univ., Pullman, WA (United States). Dept. of Chemistry

    1999-05-11

    Photoresponsive asymmetrically organized systems based upon small unilamellar dihexadecyl phosphate (DHP) vehicles were constructed by entrapping high concentrations of potassium ion within the vesicular aqueous core and incorporating either an amphiphilic trans-azobenzene-containing phosphate monoester or an amphiphilic trans-stilbene-containing carboxylic acid into its membrane structure. Spectroscopic measurements indicated that the azobenzene derivative was molecularly dispersed in the hydrocarbon phase of the vesicle and that the extent of aggregation of the membrane-localized stilbene derivative was minor. Thermal K{sup +} leak rates from the doped vesicles were very low, with calculated permeability coefficients (P) of {approximately}4 {times} 10{sup {minus}12} cm/s at 40 C for DHP vesicles containing 5.5 mol % of the trans-azobenzene derivative and {approximately}1.5 {times} 10{sup {minus}11} cm/s at 38 C for vesicles containing 5.5 mol % of the trans-stilbene derivative; for comparison, P {approx_equal} 2 {times} 10{sup {minus}12} cm/s for undoped vesicles at 40 C. Photoexcitation of the azobenzene-doped vesicles at 360 nm caused >90% trans {r_arrow} cis photoisomerization over the measured temperature range (25--40 C), with complete reversion to the trans isomer upon photoexcitation at 450 nm. Photoexcitation of deoxygenated suspensions of the stilbene-doped vesicles at 315 nm gave {approximately}80% conversion to the cis isomer in the photostationary state, which was not reversible. At 25 C, K{sup +} leak rates for the isomeric azobenzene-doped vesicles were nearly identical; at 40 C, K{sup +} leakage for the DHP vesicles containing the cis-azobenzene isomer corresponded to P {approx_equal} 2 {times} 10{sup {minus}11} cm/s, 5-fold greater than that of the trans isomer. In trans {r_arrow} cis {r_arrow} trans photocycling experiments, K{sup +} leak rates alternately increased and decreased, indicating that the vesicles remained intact. At 40 C, K

  16. Surfactant-free Gd3+-ion-containing carbon nanotube MRI contrast agents for stem cell labeling

    Science.gov (United States)

    Gizzatov, Ayrat; Hernández-Rivera, Mayra; Keshishian, Vazrik; Mackeyev, Yuri; Law, Justin J.; Guven, Adem; Sethi, Richa; Qu, Feifei; Muthupillai, Raja; Cabreira-Hansen, Maria Da Graça; Willerson, James T.; Perin, Emerson C.; Ma, Qing; Bryant, Robert G.; Wilson, Lon J.

    2015-07-01

    There is an ever increasing interest in developing new stem cell therapies. However, imaging and tracking stem cells in vivo after transplantation remains a serious challenge. In this work, we report new, functionalized and high-performance Gd3+-ion-containing ultra-short carbon nanotube (US-tube) MRI contrast agent (CA) materials which are highly-water-dispersible (ca. 35 mg ml-1) without the need of a surfactant. The new materials have extremely high T1-weighted relaxivities of 90 (mM s)-1 per Gd3+ ion at 1.5 T at room temperature and have been used to safely label porcine bone-marrow-derived mesenchymal stem cells for MR imaging. The labeled cells display excellent image contrast in phantom imaging experiments, and TEM images of the labeled cells, in general, reveal small clusters of the CA material located within the cytoplasm with 109 Gd3+ ions per cell.There is an ever increasing interest in developing new stem cell therapies. However, imaging and tracking stem cells in vivo after transplantation remains a serious challenge. In this work, we report new, functionalized and high-performance Gd3+-ion-containing ultra-short carbon nanotube (US-tube) MRI contrast agent (CA) materials which are highly-water-dispersible (ca. 35 mg ml-1) without the need of a surfactant. The new materials have extremely high T1-weighted relaxivities of 90 (mM s)-1 per Gd3+ ion at 1.5 T at room temperature and have been used to safely label porcine bone-marrow-derived mesenchymal stem cells for MR imaging. The labeled cells display excellent image contrast in phantom imaging experiments, and TEM images of the labeled cells, in general, reveal small clusters of the CA material located within the cytoplasm with 109 Gd3+ ions per cell. Electronic supplementary information (ESI) available: NMRD profiles, the Fourier transforms of the EXAFS data, EXAFS curve fitting data, cell viability data. See DOI: 10.1039/c5nr02078f

  17. Snails and slugs damaging the cut foliage, Cordyline fruticosa and use of biorationals towards their management.

    Science.gov (United States)

    Karthiga, S; Jegathambigai, V; Karunarathne, M D S D; Svinningen, A; Mikunthan, G

    2012-01-01

    Snails and slugs became a serious molluscan pests and damaging leaves of purple compacta, Cordyline fruticosa extensively grown for export at Green Farm Ltd, Sri Lanka. The export quality of leaves of C. fruticosa is lowered due to feeding of snails, Achantina fulica (Bowditch), Opeas pyrgula Schmacker and Boettgerx and Helix aspersa Muller and slugs incurring great loss to cut foliage industry. Paucity of information is available to understand snails and slugs damage and their host range that limits to develop suitable management practices. Therefore this study was aimed to determine damage, alternate hosts and to develop possible management practices. Snails and slugs damaged mainly fresh leaves of C. fruticosa. The severity of damage was 44.5% in infested field based on the visual rating method. Leaves of cassava, sting bean, okra, cucumber, passion fruit, papaya, Glyricidia and shoe flower were identified as alternate hosts and neem, Ixora and Dracaena spp were not served as alternate hosts. Among the plant materials tested for their repellence against snails and slugs revealed that neem seed powder was an irritant; neem leaves, mint leaves and Lantana leaves were acted as anti-feedant and Salt as chemical repellent. Among the barrier and bait experiments Bordeaux mixture exhibited a significant barrier effect against horizontal movement of snails. Baits made out of Metaldehyde bait, vegetables bait and jaggery had a strong effect in repelling the snails and slugs. Mulching with Madhuca longifolia punnac was the best to reduce the snails and slugs population compared to M. longifolia seed kernel powder. Oil from M. longifolia failed to reduce their population. Hence the results revealed that saponin containing M. longifolia punnac helped to eliminate snails and slugs when used as mulch. Metaldehyde, vegetable and jaggery baits are also useful to minimize their colonization further. Hence combination of these methods will help to prevent snails and slugs from

  18. Detection of Gas Slugs in Heat Pipes

    Science.gov (United States)

    Jones, J. A.

    1985-01-01

    Temperature sensing system detects presence of gas slugs in heat pipes. System designed for operation between zero and 70 degrees C and detects noncondensable pockets of gas that result from decomposition of ammonia cooling fluid. Slugs 1 in. (25mm) in length detected.

  19. Biodegradation of organic wastes containing surfactants in a biomass recycle reactor.

    Science.gov (United States)

    Konopka, A; Zakharova, T; Oliver, L; Camp, D; Turco, R F

    1996-01-01

    The microbial biodegradation of simulated graywater, containing 21.5 mg of linear alkylbenzene sulfonate liter-1, was investigated with a continuous-flow bioreactor with 100% biomass recycle. Low concentrations of organic matter in the ultrafiltration eluate were achieved by hydraulic residence times as short as 1.6 h and for periods of up to 74 days at a hydraulic residence time of 6 h. Upon a shift from the chemostat to the biomass recycle mode, the increase in biomass with time approximated a linear rather than an exponential function. Biomass densities as high as 6.8 g of cell protein liter-1 were reached; this was 50-fold higher than the steady-state biomass level in chemostats fed the same medium. We assessed physiological changes in the microbial community after a switch from the chemostat to the biomass recycle mode. Over 150 h, there was a two- to fourfold decrease in the respiratory potential of the microbes. After this decrease, respiratory potentials were relatively constant up to 74 days of operation. A decline in reactivity was also indicated by increasing lag periods before growth in response to organic nutrient inputs and by a decrease in the proportion of cells able to reduce tetrazolium dye. However, the bioreactor system was still capable of rapidly metabolizing inputs of organic matter, because of the very high biomass concentrations. It appears that < 10% of the organic carbon inputs accumulate as biomass. PMID:8795219

  20. Interfacial behavior and film patterning of redox-active cationic copper(II)-containing surfactants.

    Science.gov (United States)

    Driscoll, Jeffery A; Allard, Marco M; Wu, Libo; Heeg, Mary Jane; da Rocha, Sandro R P; Verani, Cláudio N

    2008-01-01

    Herein, we describe the synthesis and characterization of a novel series of single-tail amphiphiles LPyCn (Py=pyridine, Cn=C18, C16, C14, C10) and their copper(II)-containing complexes, which are of relevance for patterned films. The N-(pyridine-2-ylmethyl)alkyl-1-amine ligands and their complexes [CuIICl2(LPyC18)] (1), [CuIICl2(LPyC16)] (2), [CuIICl2(LPyC14)] (3), [CuIIBr2(LPyC18)] (4), [CuIIBr2(LPyC16)] (5), and [CuIIBr2(LPyC10)] (6) were synthesized, isolated, and characterized by means of mass spectrometry, IR and NMR spectroscopies, and elemental analysis. Complexes 1, 2, 3, and 6 had their molecular structure solved by X-ray diffraction methods, which showed that the local geometry around the metal center is distorted square planar. With the aim of using these species as precursors for redox-responsive films, an assessment of their electrochemical properties involved cyclic voltammetry in different solvents, with different supporting electrolytes and scan rates. Density functional theory calculations of relevant species in bulk and at interfaces were used to evaluate their electronic structure and dipole moments. The morphology and order of the resulting films at the air/water interface were studied by isothermal compression and Brewster angle microscopy. Biphasic patterned Langmuir films were observed for all complexes except 3 and 6, and dependence on the chain length and the nature of the halogen coligand determine the characteristics of the isotherms and their intricate topology. Complexes 3 and 6, which have shorter chain lengths, failed to exhibit organization. These results exemplify the first comprehensive study of the behavior of single-tail metallosurfactants, which are likely to lead to high-end technological applications based on their patterned films.

  1. Use of highly saline ethoxylated surfactant system for oil recovery

    Energy Technology Data Exchange (ETDEWEB)

    Reisberg, J.

    1970-03-17

    An aqueous solution of a sulfated polyoxylated primary alcohol and a soluble inorganic electrolyte was used for enhanced oil recovery. The electrolyte should be present in a concentration exceeding the critical concentration for forming a two-phase coacervate system, by an amount sufficient to convert the two-phase system to a turbid dispersion. The dispersion permits an interfacial tension with petroleum of 10/sup -4/ dynes/cm. A berea core (400 md) was flooded to residual oil saturation before flooding with a 4 M sodium chloride brine which contained Tergitol 15-S4 (4 ethylene oxide units, sodium salt). A 1 PV slug of the surfactant solution left only about 7 percent PV of oil.

  2. Comparative evaluation of antibacterial property and substantivity of chlorhexidine containing dentifrices with sodium lauryl sulfate and Tween as surfactants: An in vivo study

    Directory of Open Access Journals (Sweden)

    V Venu

    2013-01-01

    Full Text Available Aim: The aim of the study was to determine the antibacterial property and substantivity of chlorhexidine containing dentifrices with sodium lauryl sulfate (SLS and Tween as surfactants. Materials and Methods: It is a double-blind cross over the study, a total of 20 children within their mixed dentition period (7-13 year having Streptococci mutans count more than 10 6 were selected for the main study. Three types of chlorhexidine containing dentifrices were used with a washout period of 1 week. Out of the three toothpastes, one was without surfactant and other two toothpastes contained SLS and Tween as surfactants respectively. 20 volunteers brushed for 1 min during the study day with their assigned toothpaste. Saliva samples were collected before brushing, immediately after brushing and 1, 3, 5, and 7 hand sent for microbial analysis. The culture carried out by inoculating saliva sample onto Mitis salivarius agar for selective isolation of S. mutans followed by counting of colony forming unit. Results: Group I and III (Chlorhexidine and CHX + Tween had shown statistically significant reduction in bacterial count until 7 h when compared to their baseline values ( P < 0.001. Group II toothpaste (CHX + SLS had shown significant reduction in bacterial count until 3 h only. On inter group comparison, Group III had shown good amount of percentage reduction in bacterial count when compared to other groups. Conclusion: CHX + Tween toothpaste had shown statistically significant reduction in antibacterial activity and substantivity than other groups. These findings show chlorhexidine containing toothpaste with non-ionic surfactant will be able to maintain the antibacterial property and substantivity of chlorhexidine.

  3. Preliminary formulation and characterization of solid lipid nanoparticles containing chloroquine and a P-glycoprotein inhibitor: Influences of lipid-surfactant ratios

    CSIR Research Space (South Africa)

    Nzekwe, IT

    2015-02-01

    Full Text Available of Chemical and Pharmaceutical Research, 2015, 7(2): 932-939 Preliminary formulation and characterization of solid lipid nanoparticles containing chloroquine and a P-glycoprotein inhibitor: Influences of lipid-surfactant ratios Ifeanyi T. Nzekwea...*, Valentine I. Azodoa , Chukwuma O. Agubatab , Brendon Naickerc , Vincent Okored and Charles O. Esimonee aDepartment of Pharmaceutics and Pharmaceutical Technology, Nnamdi Azikiwe University, Awka, Anambra State, Nigeria bDepartment of Pharmaceutical...

  4. Slug controls stem/progenitor cell growth dynamics during mammary gland morphogenesis.

    Directory of Open Access Journals (Sweden)

    Mayssa Nassour

    Full Text Available BACKGROUND: Morphogenesis results from the coordination of distinct cell signaling pathways controlling migration, differentiation, apoptosis, and proliferation, along stem/progenitor cell dynamics. To decipher this puzzle, we focused on epithelial-mesenchymal transition (EMT "master genes". EMT has emerged as a unifying concept, involving cell-cell adhesion, migration and apoptotic pathways. EMT also appears to mingle with stemness. However, very little is known on the physiological role and relevance of EMT master-genes. We addressed this question during mammary morphogenesis. Recently, a link between Slug/Snai2 and stemness has been described in mammary epithelial cells, but EMT master genes actual localization, role and targets during mammary gland morphogenesis are not known and we focused on this basic question. METHODOLOGY/PRINCIPAL FINDINGS: Using a Slug-lacZ transgenic model and immunolocalization, we located Slug in a distinct subpopulation covering about 10-20% basal cap and duct cells, mostly cycling cells, coexpressed with basal markers P-cadherin, CK5 and CD49f. During puberty, Slug-deficient mammary epithelium exhibited a delayed development after transplantation, contained less cycling cells, and overexpressed CK8/18, ER, GATA3 and BMI1 genes, linked to luminal lineage. Other EMT master genes were overexpressed, suggesting compensation mechanisms. Gain/loss-of-function in vitro experiments confirmed Slug control of mammary epithelial cell luminal differentiation and proliferation. In addition, they showed that Slug enhances specifically clonal mammosphere emergence and growth, cell motility, and represses apoptosis. Strikingly, Slug-deprived mammary epithelial cells lost their potential to generate secondary clonal mammospheres. CONCLUSIONS/SIGNIFICANCE: We conclude that Slug pathway controls the growth dynamics of a subpopulation of cycling progenitor basal cells during mammary morphogenesis. Overall, our data better define a

  5. Fern and bryophyte endozoochory by slugs.

    Science.gov (United States)

    Boch, Steffen; Berlinger, Matthias; Fischer, Markus; Knop, Eva; Nentwig, Wolfgang; Türke, Manfred; Prati, Daniel

    2013-07-01

    Endozoochory plays a prominent role for the dispersal of seed plants, and dispersal vectors are well known. However, for taxa such as ferns and bryophytes, endozoochory has only been suggested anecdotally but never tested in controlled experiments. We fed fertile leaflets of three ferns and capsules of four bryophyte species to three slug species. We found that, overall, spores germinated from slug feces in 57.3% of all 89 fern and in 51.3% of all 117 bryophyte samples, showing that the spores survived gut passage of slugs. Moreover, the number of samples within which spores successfully germinated did not differ among plant species but varied strongly among slug species. This opens new ecological perspectives suggesting that fern and bryophyte endozoochory by gastropods is a so-far-overlooked mode of dispersal, which might increase local population sizes of these taxa by spore deposition on suitable substrates.

  6. Shell tension forces propel Dictyostelium slugs forward.

    Science.gov (United States)

    Rieu, Jean-Paul; Delanoë-Ayari, Hélène

    2012-12-01

    The Dictyostelium slug is an excellent model system for studying collective movements, as it is comprised of about 10(5) cells all moving together in the same direction. It still remains unclear how this movement occurs and what the physical mechanisms behind it are. By applying our recently developed 3D traction force microscopy, we propose a simple explanation for slug propulsion. Most of the forces are exerted by the sheath surrounding the slug. This secreted shell is under a rather uniform tension (around 50 mN m(-1)) and will give rise to a tissue under pressure. Finally, we propose that this pressure will naturally push the slug tip forwards if a gradient of shell mechanical properties takes place in the very anterior part of the raised tip.

  7. Shell tension forces propel Dictyostelium slugs forward

    Science.gov (United States)

    Rieu, Jean-Paul; Delanoë-Ayari, Hélène

    2012-12-01

    The Dictyostelium slug is an excellent model system for studying collective movements, as it is comprised of about 105 cells all moving together in the same direction. It still remains unclear how this movement occurs and what the physical mechanisms behind it are. By applying our recently developed 3D traction force microscopy, we propose a simple explanation for slug propulsion. Most of the forces are exerted by the sheath surrounding the slug. This secreted shell is under a rather uniform tension (around 50 mN m-1) and will give rise to a tissue under pressure. Finally, we propose that this pressure will naturally push the slug tip forwards if a gradient of shell mechanical properties takes place in the very anterior part of the raised tip.

  8. OIL SLUGS FOR PRODUCTION OF PISTON RING

    Directory of Open Access Journals (Sweden)

    V. F. Bevza

    2008-01-01

    Full Text Available The developed technological process of continuously cyclic casting by frosting allows to receive high-quality hollow cylindrical slugs of cast iron for production of critical parts. 

  9. Gas slug ascent through rheologically stratified conduits

    Science.gov (United States)

    Capponi, Antonio; James, Mike R.; Lane, Steve J.

    2016-04-01

    Textural and petrological evidence has indicated the presence of viscous, degassed magma layers at the top of the conduit at Stromboli. This layer acts as a plug through which gas slugs burst and it is thought to have a role in controlling the eruptive dynamics. Here, we present the results of laboratory experiments which detail the range of slug flow configurations that can develop in a rheologically stratified conduit. A gas slug can burst (1) after being fully accommodated within the plug volume, (2) whilst its base is still in the underlying low-viscosity liquid or (3) within a low-viscosity layer dynamically emplaced above the plug during the slug ascent. We illustrate the relevance of the same flow configurations at volcanic-scale through a new experimentally-validated 1D model and 3D computational fluid dynamic simulations. Applied to Stromboli, our results show that gas volume, plug thickness, plug viscosity and conduit radius control the transition between each configuration; in contrast, the configuration distribution seems insensitive to the viscosity of magma beneath the plug, which acts mainly to deliver the slug into the plug. Each identified flow configuration encompasses a variety of processes including dynamic narrowing and widening of the conduit, generation of instabilities along the falling liquid film, transient blockages of the slug path and slug break-up. All these complexities, in turn, lead to variations in the slug overpressure, mirrored by changes in infrasonic signatures which are also associated to different eruptive styles. Acoustic amplitudes are strongly dependent on the flow configuration in which the slugs burst, with both acoustic peak amplitudes and waveform shapes reflecting different burst dynamics. When compared to infrasonic signals from Stromboli, the similarity between real signals and laboratory waveforms suggests that the burst of a slug through a plug may represent a viable first-order mechanism for the generation of

  10. Interaction of the C-terminal peptide of pulmonary surfactant protein B (SP-B with a bicellar lipid mixture containing anionic lipid.

    Directory of Open Access Journals (Sweden)

    Alexander Sylvester

    Full Text Available The hydrophobic lung surfactant SP-B is essential for respiration. SP-B promotes spreading and adsorption of surfactant at the alveolar air-water interface and may facilitate connections between the surface layer and underlying lamellar reservoirs of surfactant material. SP-B63-78 is a cationic and amphipathic helical peptide containing the C-terminal helix of SP-B. (2H NMR has been used to examine the effect of SP-B63-78 on the phase behavior and dynamics of bicellar lipid dispersions containing the longer chain phospholipids DMPC-d 54 and DMPG and the shorter chain lipid DHPC mixed with a 3∶1∶1 molar ratio. Below the gel-to-liquid crystal phase transition temperature of the longer chain components, bicellar mixtures form small, rapidly reorienting disk-like particles with shorter chain lipid components predominantly found around the highly curved particle edges. With increasing temperature, the particles coalesce into larger magnetically-oriented structures and then into more extended lamellar phases. The susceptibility of bicellar particles to coalescence and large scale reorganization makes them an interesting platform in which to study peptide-induced interactions between lipid assemblies. SP-B63-78 is found to lower the temperature at which the orientable phase transforms to the more extended lamellar phase. The peptide also changes the spectrum of motions contributing to quadrupole echo decay in the lamellar phase. The way in which the peptide alters interactions between bilayered micelle structures may provide some insight into some aspects of the role of full-length SP-B in maintaining a functional surfactant layer in lungs.

  11. Effect of light on self-assembly of aqueous mixtures of sodium dodecyl sulfate and a cationic, bolaform surfactant containing azobenzene.

    Science.gov (United States)

    Hubbard, F Pierce; Abbott, Nicholas L

    2007-04-24

    We report light and small-angle neutron scattering measurements that characterize microstructures formed in aqueous surfactant solutions (up to 1.0 wt % surfactant) containing mixtures of sodium dodecyl sulfate (SDS) and the light-sensitive bolaform surfactant, bis(trimethylammoniumhexyloxy)azobenzene dibromide (BTHA) as a function of composition, equilibration time, and photostationary state (i.e., solutions rich in cis-BTHA or trans-BTHA). We observed formation of vesicles in both SDS-rich and trans-BTHA-rich regions of the microstructure diagram, with vesicles present over a particularly broad range of compositions for trans-BTHA-rich solutions. Illumination of mixtures of BTHA and SDS with a broadband UV light source leads to formation of photostationary states where the fraction of BTHA present as cis isomer (75-80% cis-BTHA) is largely independent of the mixing ratio of SDS and BTHA. For a relatively limited set of mixing ratios of SDS and BTHA, we observed UV illumination of SDS-rich vesicles to result in the reversible transformation of the vesicles to micellar aggregates and UV illumination of BTHA-rich vesicles to result in irreversible precipitation. Surprisingly, however, for many mixtures of trans-BTHA and SDS that formed solutions containing vesicles, illumination with UV light (which was confirmed to lead to photoisomerization of BTHA) resulted in only a small decrease in the number of vesicles in solution, relatively little change in the sizes of the remaining vesicles, and coexistance of the vesicles with micelles. These observations are consistent with a physical model in which the trans and cis isomers of BTHA present at the photostationary state tend to segregate between the different microstructures coexisting in solution (e.g., vesicles rich in trans-BTHA and SDS coexist with micelles rich in cis-BTHA and SDS). The results presented in this paper provide guidance for the design of light-tunable surfactants systems.

  12. Interaction of the C-terminal peptide of pulmonary surfactant protein B (SP-B) with a bicellar lipid mixture containing anionic lipid.

    Science.gov (United States)

    Sylvester, Alexander; MacEachern, Lauren; Booth, Valerie; Morrow, Michael R

    2013-01-01

    The hydrophobic lung surfactant SP-B is essential for respiration. SP-B promotes spreading and adsorption of surfactant at the alveolar air-water interface and may facilitate connections between the surface layer and underlying lamellar reservoirs of surfactant material. SP-B63-78 is a cationic and amphipathic helical peptide containing the C-terminal helix of SP-B. (2)H NMR has been used to examine the effect of SP-B63-78 on the phase behavior and dynamics of bicellar lipid dispersions containing the longer chain phospholipids DMPC-d 54 and DMPG and the shorter chain lipid DHPC mixed with a 3∶1∶1 molar ratio. Below the gel-to-liquid crystal phase transition temperature of the longer chain components, bicellar mixtures form small, rapidly reorienting disk-like particles with shorter chain lipid components predominantly found around the highly curved particle edges. With increasing temperature, the particles coalesce into larger magnetically-oriented structures and then into more extended lamellar phases. The susceptibility of bicellar particles to coalescence and large scale reorganization makes them an interesting platform in which to study peptide-induced interactions between lipid assemblies. SP-B63-78 is found to lower the temperature at which the orientable phase transforms to the more extended lamellar phase. The peptide also changes the spectrum of motions contributing to quadrupole echo decay in the lamellar phase. The way in which the peptide alters interactions between bilayered micelle structures may provide some insight into some aspects of the role of full-length SP-B in maintaining a functional surfactant layer in lungs.

  13. Surfactants induced release of a red emitting dye from the nanocavity of a molecular container: A spectroscopic and calorimetric study.

    Science.gov (United States)

    Ahmed, Sayeed Ashique; Chatterjee, Aninda; Maity, Banibrata; Seth, Debabrata

    2016-08-01

    Supramolecular interaction of a red emitting dye Nile blue A (NBA) with Cucurbit[7]uril (CB7) in aqueous solution was studied and the release of the dye from the hydrophobic cavity of CB7 was reported. To investigate the supramolecular host-guest complex formation and release of dye, we have used the steady state absorption, fluorescence and time resolved fluorescence emission spectroscopy, (1)H NMR spectroscopy and isothermal titration calorimetry (ITC). The spectral properties of NBA were changed in the presence of CB7. The change in spectral features of NBA in presence of CB7 indicates the formation of supramolecular host-guest complexes. By using the SED equation the diameter of the complex was estimated. The complex formation further affirmed by the (1)H NMR study. Upfield and downfield shifts of the protons of NBA was observed in both the aliphatic and aromatic region. From the ITC measurement, we have drawn up the forces involved for the complexation of NBA with CB7. We have studied the release of NBA from the hydrophobic cavity of CB7 by using ionic, neutral surfactants and ionic liquid with the help of spectroscopic and calorimetric techniques. It is observed that on addition of SDS and ionic liquid (surfactant monomer whereas, it was not observed for neutral and cationic surfactant. Above cmc of the surfactants, complex is formed between NBA and micelle.

  14. Surfactant Based Enhanced Oil Recovery and Foam Mobility Control

    Energy Technology Data Exchange (ETDEWEB)

    George J. Hirasaki; Clarence A. Miller

    2006-09-09

    Surfactant flooding has the potential to significantly increase recovery over that of conventional waterflooding. The availability of a large number of surfactant structures makes it possible to conduct a systematic study of the relation between surfactant structure and its efficacy for oil recovery. A mixture of two surfactants was found to be particularly effective for application in carbonate formations at low temperature. The mixture is single phase for higher salinity or calcium concentrations than that for either surfactant used alone. This makes it possible to inject the surfactant slug with polymer close to optimal conditions and yet be single phase. A formulation has been designed for a particular field application. It uses partially hydrolyzed polyacrylamide for mobility control. The addition of an alkali such as sodium carbonate makes possible in situ generation of naphthenic soap and significant reduction of synthetic surfactant adsorption. The design of the process to maximize the region of ultra-low IFT takes advantage of the observation that the ratio of soap to synthetic surfactant is a parameter in the conditions for optimal salinity. Even for a fixed ratio of soap to surfactant, the range of salinity for low IFT was wider than that reported for surfactant systems in the literature. Low temperature, forced displacement experiments in dolomite and silica sandpacks demonstrate that greater than 95% recovery of the waterflood remaining oil is possible with 0.2% surfactant concentration, 0.5 PV surfactant slug, with no alcohol. Compositional simulation of the displacement process demonstrates the role of soap/surfactant ratio on passage of the profile through the ultralow IFT region, the importance of a wide salinity range of low IFT, and the importance of the viscosity of the surfactant slug. Mobility control is essential for surfactant EOR. Foam is evaluated to improve the sweep efficiency of surfactant injected into fractured reservoirs as well as a

  15. Recovering hydrocarbons with surfactants from lignin

    Energy Technology Data Exchange (ETDEWEB)

    Naae, D.G.; Whittington, L.E.; Ledoux, W.A.; Debons, F.E.

    1988-11-29

    This patent describes a method of recovering hydrocarbons from an underground hydrocarbon formation penetrated by at least one injection well and at least one production well, which comprises: injecting into the formation through an injection well a surfactant slug comprising about 0.1% to about 10% by weight of surfactants produced from lignin, the surfactants produced by placing lignin in contact with water, converting the lignin into low molecular weight lignin phenols by reducing the lignin in the presence of a reducing agent of carbon monoxide or hydrogen creating a reduction reaction mixture comprising oil soluble lignin phenols, the reduction occurring at a temperature greater than about 200/sup 0/C and a pressure greater than about 100 psi, recovering the oil soluble lignin phenols from the reduction mixture, and converting the lignin phenols into lignin surfactants by a reaction selected from the group consisting of alkoxylation, sulfonation, sulfation, aklylation, sulfomethylation, and alkoxysulfation; injecting into the formation through the injection well a drive fluid to push the surfactant slug towards a production well; and recovering hydrocarbons at the production well.

  16. Structure and rheology of semisolid o/w creams containing cetyl alcohol/non-ionic surfactant mixed emulsifier and different polymers.

    Science.gov (United States)

    Ribeiro, H M; Morais, J A; Eccleston, G M

    2004-04-01

    Oil-in-water (o/w) emulsions for cosmetic use, such as lotions and creams, are complex multiple-phase systems, which may contain a number of interacting surfactants, fatty amphiphiles, polymers and other excipients. This study investigates the influence of two synthetic cationic polymers, Polyquaternium-7 and Polyquaternium-11, and the natural anionic polymer, gum of acacia, on the rheology and microstructure of creams prepared with a non-ionic mixed emulsifier (cetyl stearyl alcohol-12EO/cetyl alcohol) using rheology (continuous shear, and viscoelastic creep and oscillation), microscopy and differential scanning calorimetry (DSC). A control cream containing no polymer was also investigated. The semisolid control cream was structured by a swollen lamellar gel network phase formed from the interaction of cetyl alcohol and the POE surfactant, in excess of that required to stabilize oil droplets, with continuous phase water. Endothermic transitions between 25 and 100 degrees C were identified as components of this phase. Incorporation of cationic polymer into the formulation caused significant loss of structure to produce a mobile semisolid containing larger oil droplets. The microscopical and thermal data implied that the cationic polymer caused the swollen lamellar gel network phase to transform into non-swollen crystals of cetyl alcohol. In contrast, incorporation of gum of acacia produced a thicker cream than the control, with smaller droplet sizes and little evidence of the gel network. Microscopical and thermal data implied that although there were also interactions between gum of acacia and both the surfactant and the swollen gel network phase, the semisolid properties were probably because of the ability of the gum of acacia to stabilize and thicken the emulsion in the absence of the swollen lamellar network.

  17. Slug Controls Stem/Progenitor Cell Growth Dynamics during Mammary Gland Morphogenesis

    Science.gov (United States)

    Selmi, Abdelkader; Côme, Christophe; Faraldo, Maria-Luisa M.; Deugnier, Marie-Ange; Savagner, Pierre

    2012-01-01

    Background Morphogenesis results from the coordination of distinct cell signaling pathways controlling migration, differentiation, apoptosis, and proliferation, along stem/progenitor cell dynamics. To decipher this puzzle, we focused on epithelial-mesenchymal transition (EMT) “master genes”. EMT has emerged as a unifying concept, involving cell-cell adhesion, migration and apoptotic pathways. EMT also appears to mingle with stemness. However, very little is known on the physiological role and relevance of EMT master-genes. We addressed this question during mammary morphogenesis. Recently, a link between Slug/Snai2 and stemness has been described in mammary epithelial cells, but EMT master genes actual localization, role and targets during mammary gland morphogenesis are not known and we focused on this basic question. Methodology/Principal Findings Using a Slug–lacZ transgenic model and immunolocalization, we located Slug in a distinct subpopulation covering about 10–20% basal cap and duct cells, mostly cycling cells, coexpressed with basal markers P-cadherin, CK5 and CD49f. During puberty, Slug-deficient mammary epithelium exhibited a delayed development after transplantation, contained less cycling cells, and overexpressed CK8/18, ER, GATA3 and BMI1 genes, linked to luminal lineage. Other EMT master genes were overexpressed, suggesting compensation mechanisms. Gain/loss-of-function in vitro experiments confirmed Slug control of mammary epithelial cell luminal differentiation and proliferation. In addition, they showed that Slug enhances specifically clonal mammosphere emergence and growth, cell motility, and represses apoptosis. Strikingly, Slug-deprived mammary epithelial cells lost their potential to generate secondary clonal mammospheres. Conclusions/Significance We conclude that Slug pathway controls the growth dynamics of a subpopulation of cycling progenitor basal cells during mammary morphogenesis. Overall, our data better define a key mechanism

  18. Determination of slug permeability factor for pressure drop prediction of slug flow pneumatic conveying

    Institute of Scientific and Technical Information of China (English)

    Shengming Tan; Kenneth C.Williams; Mark G.Jones; Tobias Krull

    2008-01-01

    Current models for pressure drop prediction of slug flow pneumatic conveying in a horizontal pipeline system assume some type of steady state conditions for prediction,which limits their capability for increased predictive accuracy relative to experimental data.This is partly because of the nature of slug flow pneumatic conveying system,which,as a dynamic system,never becomes stable.By utilising conservation of mass (airflow),a dynamic pressure analysis model is proposed on the basis of the derivative of the upstream pressure behaviour.The rate of air permeation through slug,one of the important factors in the conservation model,is expressed as a function of a slug permeability factor.Other factors such as slug velocity,slug length and the fraction of stationary layer were also considered.Several test materials were conveyed in single-slug tests to verify the proposed pressure drop model,showing good agreement between the model and experimental results.

  19. Synthesis, micellization behavior, antimicrobial and intercalative DNA binding of some novel surfactant copper(II) complexes containing modified phenanthroline ligands.

    Science.gov (United States)

    Nagaraj, Karuppiah; Ambika, Subramanian; Rajasri, Shanmugasundaram; Sakthinathan, Subramanian; Arunachalam, Sankaralingam

    2014-10-01

    The novel surfactant copper(II) complexes, [Cu(ip)2DA](ClO4)21, [Cu(dpqc)2DA](ClO4)22, [Cu(dppn)2DA](ClO4)23, where ip=imidazo[4,5-f][1,10]phenanthroline, dpqc=dipyrido[3,2-a:2',4'-c](6,7,8,9-tetrahydro)phenazine, dppn=benzo[1]dipyrido[3,2-a':2',3'-c]phenazine and DA-dodecylamine, were synthesized and characterized by physico-chemical and spectroscopic methods. In these complexes 1-3, the geometry of copper metal ions was described as square pyramidal. The critical micelle concentration (CMC) value of these surfactant copper(II) complexes in aqueous solution was found out from conductance measurements. Specific conductivity data at different temperatures served for the evaluation of the temperature-dependent CMC and the thermodynamics of micellization (ΔGm°, ΔHm° and ΔSm°). The binding interaction of these complexes with DNA (calf thymus DNA) in Tris buffer was studied by physico-chemical techniques. In the presence of the DNA UV-vis spectrum of complexes showed red shift of the absorption band along with significant hypochromicity indicating intercalation of our complexes with nucleic acids. Competitive binding study with ethidium bromide (EB) shows that the complexes exhibit the ability to displace the nucleic acid-bound EB indicating that the complexes bind to nucleic acids in strong competition with EB for the intercalative binding site. Observed changes in the circular dichoric spectra of DNA in the presence of surfactant complexes support the strong binding of complexes with DNA. CV results also confirm this mode of binding. Some significant thermodynamic parameters of the binding of the titled complexes to DNA have also been determined. The results reveal that the extent of DNA binding of 3 was greater than that of 1 and 2. The antibacterial and antifungal screening tests of these complexes have shown good results compared to its precursor chloride complexes.

  20. Heat transfer behaviour of silver particles containing oleic acid surfactant: application in a two phase closed rectangular cross sectional thermosyphon (RTPTC)

    Science.gov (United States)

    Bhuwakietkumjohn, N.; Parametthanuwat, T.

    2017-01-01

    This article focuses on heat transfer behaviour of silver nanoparticles containing oleic acid surfactant (OA) applied as a working fluid in a two-phase closed rectangular cross sectional thermosyphon (RTPTC). Thus, the OA could reduce the surface tension of the working fluid, which improved the colloidal ability and increased the lead-time period for nanoparticles to be uniformly dispersed. It highlights theories for investigating the effects on heat transfer characteristics of RTPTC such as heat transfer rate, thermal resistance, heat transfer coefficients and nanofluids behaviour. The most important heat transfer characteristic to be examined in this experiment is the relative thermal efficiency ( R T ). Five working fluids were tested, these include: de-ionized water; de-ionized water base with a silver nanoparticles concentration of 0.5 wt% (NP); and NP containing 0.5; 1; and 1.5 wt% of OA respectively. The results showed that 0.5 wt% NP containing 1 wt% OA produced the best results. It was further found that the heat transfer rate of 0.5 wt% NP containing 1 wt% of OA with a R T value of 1, was the highest across all experimental parameters studied. The NP containing OA demonstrated approximately 80 % higher heat transfer rate than the de-ionized water.

  1. Heat transfer behaviour of silver particles containing oleic acid surfactant: application in a two phase closed rectangular cross sectional thermosyphon (RTPTC)

    Science.gov (United States)

    Bhuwakietkumjohn, N.; Parametthanuwat, T.

    2016-03-01

    This article focuses on heat transfer behaviour of silver nanoparticles containing oleic acid surfactant (OA) applied as a working fluid in a two-phase closed rectangular cross sectional thermosyphon (RTPTC). Thus, the OA could reduce the surface tension of the working fluid, which improved the colloidal ability and increased the lead-time period for nanoparticles to be uniformly dispersed. It highlights theories for investigating the effects on heat transfer characteristics of RTPTC such as heat transfer rate, thermal resistance, heat transfer coefficients and nanofluids behaviour. The most important heat transfer characteristic to be examined in this experiment is the relative thermal efficiency (R T ). Five working fluids were tested, these include: de-ionized water; de-ionized water base with a silver nanoparticles concentration of 0.5 wt% (NP); and NP containing 0.5; 1; and 1.5 wt% of OA respectively. The results showed that 0.5 wt% NP containing 1 wt% OA produced the best results. It was further found that the heat transfer rate of 0.5 wt% NP containing 1 wt% of OA with a R T value of 1, was the highest across all experimental parameters studied. The NP containing OA demonstrated approximately 80 % higher heat transfer rate than the de-ionized water.

  2. A Study of Bubble and Slug Gas-Liquid Flow in a Microgravity Environment

    Science.gov (United States)

    McQuillen, J.

    2000-01-01

    surfactant), to identify clusters that promote coalescence and transition the void fraction distribution in bubbly and slug flow,to measure the wall friction in bubbly flow. These experiments will consist of multiple bubbles type flows and will utilize hot wire and film anemometers to measure liquid velocity and wall shear stress respectively and double fiber optic probes to measure bubble size and velocity as a function of tube radius and axial location.

  3. Enhanced photocatalytic degradation of norfloxacin in aqueous Bi2WO6 dispersions containing nonionic surfactant under visible light irradiation.

    Science.gov (United States)

    Tang, Lin; Wang, Jiajia; Zeng, Guangming; Liu, Yani; Deng, Yaocheng; Zhou, Yaoyu; Tang, Jing; Wang, Jingjing; Guo, Zhi

    2016-04-05

    Photocatalytic degradation is an alternative method to remove pharmaceutical compounds in water, however it is hard to achieve efficient rate because of the poor solubility of pharmaceutical compounds in water. This study investigated the photodegradation of norfloxacin in a nonionic surfactant Triton-X100 (TX100)/Bi2WO6 dispersion under visible light irradiation (400-750nm). It was found that the degradation of poorly soluble NOF can be strongly enhanced with the addition of TX100. TX100 was adsorbed strongly on Bi2WO6 surface and accelerated NOF photodegradation at the critical micelle concentration (CMC=0.25mM). Higher TX100 concentration (>0.25mM) lowered the degradation rate. In the presence of TX100, the degradation rate reached the maximum value when the pH value was 8.06. FTIR analyses demonstrated that the adsorbed NOF on the catalyst was completely degraded after 2h irradiation. According to the intermediates identified by HPLC/MS/MS, three possible degradation pathways were proposed to include addition of hydroxyl radical to quinolone ring, elimination of piperazynilic ring in fluoroquinolone molecules, and replacement of F atoms on the aromatic ring by hydroxyl radicals. Copyright © 2015 Elsevier B.V. All rights reserved.

  4. Polystyrene latex particles containing europium complexes prepared by miniemulsion polymerization using bovine serum albumin as a surfactant for biochemical diagnosis.

    Science.gov (United States)

    Aikawa, Tatsuo; Mizuno, Akihiro; Kohri, Michinari; Taniguchi, Tatsuo; Kishikawa, Keiki; Nakahira, Takayuki

    2016-09-01

    Luminescent particles have been attracting significant attention because they can be used in biochemical applications, such as detecting and imaging biomolecules. In this study, luminescent polystyrene latex particles were prepared through miniemulsion polymerization of styrene with dissolved europium complexes in the presence of bovine serum albumin (BSA) and poly(ethylene glycol) monomethoxy methacrylate as surfactants. The solubility of the europium complex in styrene has a strong effect on the yield of the particle. Europium tris(2-thenoyl trifluoroacetonate) di(tri-n-octyl phosphine oxide), which has a high solubility in styrene, was sufficiently incorporated into the polystyrene particles compared to europium tris(2-thenoyl trifluoroacetonate), which has a low solubility in styrene. The luminescence property of the europium complex could remain intact even after its incorporation through the miniemulsion polymerization. In the aqueous dispersion, the resulting particles could emit strong luminescence, which is a characteristic of the europium complex. The antibody fragments were covalently attached to BSA-covered particles after a reaction with a bifunctional linker, N-(6-maleimidocaproyloxy)succinimide. The time-resolved fluoroimmunoassay technique showed that 3.3pg/mL of human α-fetoproteins (AFP) can be detected by using the resulting luminescent particles. An immunochromatographic assay using the resulting particles was also performed as a convenient method to qualitatively detect biomolecules. The detection limit of AFP measured by the immunochromatographic assay was determined to be 2000pg/mL. These results revealed that the luminescent particles obtained in this study can be utilized for the highly sensitive detection of biomolecules and in vitro biochemical diagnosis.

  5. Synthetic surfactant containing SP-B and SP-C mimics is superior to single-peptide formulations in rabbits with chemical acute lung injury

    Directory of Open Access Journals (Sweden)

    Frans J. Walther

    2014-05-01

    Full Text Available Background. Chemical spills are on the rise and inhalation of toxic chemicals may induce chemical acute lung injury (ALI/acute respiratory distress syndrome (ARDS. Although the pathophysiology of ALI/ARDS is well understood, the absence of specific antidotes has limited the effectiveness of therapeutic interventions.Objectives. Surfactant inactivation and formation of free radicals are important pathways in (chemical ALI. We tested the potential of lipid mixtures with advanced surfactant protein B and C (SP-B and C mimics to improve oxygenation and lung compliance in rabbits with lavage- and chemical-induced ALI/ARDS.Methods. Ventilated young adult rabbits underwent repeated saline lung lavages or underwent intratracheal instillation of hydrochloric acid to induce ALI/ARDS. After establishment of respiratory failure rabbits were treated with a single intratracheal dose of 100 mg/kg of synthetic surfactant composed of 3% Super Mini-B (S-MB, a SP-B mimic, and/or SP-C33 UCLA, a SP-C mimic, in a lipid mixture (DPPC:POPC:POPG 5:3:2 by weight, the clinical surfactant Infasurf®, a bovine lung lavage extract with SP-B and C, or synthetic lipids alone. End-points consisted of arterial oxygenation, dynamic lung compliance, and protein and lipid content in bronchoalveolar lavage fluid. Potential mechanism of surfactant action for S-MB and SP-C33 UCLA were investigated with captive bubble surfactometry (CBS assays.Results. All three surfactant peptide/lipid mixtures and Infasurf equally lowered the minimum surface tension on CBS, and also improved oxygenation and lung compliance. In both animal models, the two-peptide synthetic surfactant with S-MB and SP-C33 UCLA led to better arterial oxygenation and lung compliance than single peptide synthetic surfactants and Infasurf. Synthetic surfactants and Infasurf improved lung function further in lavage- than in chemical-induced respiratory failure, with the difference probably due to greater capillary

  6. Water-contained surfactant-based vortex-assisted microextraction method combined with liquid chromatography for determination of synthetic antioxidants from edible oil.

    Science.gov (United States)

    Amlashi, Nadiya Ekbatani; Hadjmohammadi, Mohammad Reza; Nazari, Seyed Saman Seyed Jafar

    2014-09-26

    For the first time, a novel water-contained surfactant-based vortex-assisted microextraction method (WSVAME) was developed for the extraction of two synthetic antioxidants (t-butyl hydroquinone (TBHQ) and butylated hydroxyanisole (BHA)) from edible oil samples. The novel microextraction method is based on the injection of an aqueous solution of non-ionic surfactant, Brij-35, into the oil sample in a conical bottom glass tube to form a cloudy solution. Vortex mixing was applied to accelerate the dispersion process. After extraction and phase separation by centrifugation, the lower sediment phase was directly analyzed by HPLC. The effects of the four experimental parameters including volume and concentration of extraction solvent (aqueous solution of Brij-35), percentage of acetic acid added to the oil sample and vortex time on the extraction efficiency were studied with a full factorial design. The central composite design and multiple linear regression method were applied for the construction of the best polynomial model based on experimental recoveries. The proposed method showed good linearity within the range of 0.200-200 μg mL(-1), the square of correlation coefficient higher than 0.999 and appropriate limit of detection (0.026 and 0.020 μg mL(-1) for TBHQ and BHA, respectively), while the precision for inner-day was ≤ 3.0 (n=5) and it was ≤ 3.80 (n=5) for inter-day assay. Under the optimal condition (30 μL of 0.10 mol L(-1) Brij-35 solution as extraction solvent and vortex time 1 min), the method was successfully applied for determination of TBHQ and BHA in different commercial edible oil samples. The recoveries in all cases were above 95%, with relative standard deviations below 5%. This approach is considered as a simple, sensitive and environmentally friendly method because of biodegradability of the extraction phase and no use of organic solvent in the extraction procedure.

  7. Surface active properties and biological activity of novel nonionic surfactants containing pyrimidines and related nitrogen heterocyclic ring systems

    Directory of Open Access Journals (Sweden)

    El-Sayed, R.

    2008-06-01

    Full Text Available A series of annelated pyrimidine derivatives has been synthesized via different heterocyclization reactions of suitably functionalized 6-(4-octadecyloxyphenyl-4-oxo-2- thioxo-1,2,3,4-tetrahydropyrimidine-5-carbonitrile (4 with different electrophiles and nucleophiles. These heterocycles bear an active hydrogen atom (NH, OH or COOH which could be propoxylated using propylene oxide with different moles, 5, 10 and 15, to produce nonionic surfactant having a long alkyl chain with molecular weight suitable for becoming an amphiphilic molecule with correct hydrophilic-lypophilic balance which enhances solubility, biodegradability and hence lowers the toxicity to human beings and becomes environmentally friendly. In addition, the antimicrobial activities of these compounds were screened and it was found that some of these compounds have similar or higher activity compared with commercial antibiotic drugs (sulphadiazine, which make them suitable for diverse applications like the manufacturing of drugs, pesticides, emulsifiers, cosmetics, etc.Una serie de derivados pirimidínicos y relacionados han sido preparados vía diferentes reacciones de formación de heterociclos entre 6-(4-octadeciloxifenil-4-oxo-2-tioxo- 1,2,3,4-tetrahidropirimidina-5-carbonitrilo (4 y diferentes electrófilos y nucleófilos. Estos heterociclos tienen un átomo de hidrógeno activo (NH, OH, o COOH que fue propoxilado con diferentes moles de óxido de propileno (5, 10, o 15 para producir surfactantes no iónicos con una cadena alquílica larga y peso molecular apropiado para convertirse en una molécula anfifílica con un balance hidrofílico-lipofílico correcto que aumenta la solubilidad y la biodedradabilidad, decrece la toxicidad a los seres humanos, y se convierte en respetuoso con el medio ambiente. Además, las actividades antimicrobianas de estos compuestos fueron determinadas y se encontró que algunos de estos compuestos tuvieron una actividad similar o más alta que

  8. A study of correlations between the release of drugs from petrolatum-based gels containing nonionic surfactants and some physical and physico-chemical characteristics of the gel systems.

    Science.gov (United States)

    Colo, G D; Nannipieri, E; Serafini, M F; Vitale, D

    1986-06-01

    Synopsis The in vitro release of benzocaine and 2-ethyIhexyl p-di-methylaminobenzoate (EH-PABA) from petrolatum-based gels either containing two nonionic surfactants, or not, was compared with some physical and/or physico-chemical characteristics of the drugs, the gels and the drug-gel systems. The surfactants had no effect on the release of EH-PABA, the less polar drug, whereas they decreased the release of benzocaine. Moreover, the release data show a complex dependence of diffusive properties of ben-zocaine on drug and surfactant concentration. Benzocaine appears to form mixed micelles with each of the two surfactants and/or undergoes self-aggregation phenomena within surfactant micelles. The results indicate that drug diffusion is influenced by gel porosity, drug molecular size and polarity and molecular interactions. Etude des corrélations entre la disponibilité des medicaments dans les gels a base de vaseline contenant des surfactifs non ioniques et quelques propriétés physiques et physicochimiques des gels.

  9. Formation of macroporous gel morphology by phase separation in the silica sol-gel system containing nonionic surfactant

    Institute of Scientific and Technical Information of China (English)

    Junsheng Wu; Xiaogang Li; Wei Du; Hua Chen

    2005-01-01

    The phase separation and gel formation behavior in an alkoxy-derived silica sol-gel system containing Ci6EOi5 has been investigated. Various gel morphologies similar to other sol-gel systems containing organic additives were obtained by changing the preparation conditions. Micrometer-range interconnected porous gels were obtained by freezing transitional structures of phase separation in the sol-gel process. The dependence of the resulting gel morphology on several important reaction parameters such as the starting composition, reaction temperature and acid catalyst concentration was studied in detail. The experimental results indicate that the gel morphology is mainly determined by the time relation between the onset of phase separation and gel formation.

  10. Screening of mixed surfactant systems: Phase behavior studies and CT imaging of surfactant-enhanced oil recovery experiments

    Energy Technology Data Exchange (ETDEWEB)

    Llave, F.M.; Gall, B.L.; Lorenz, P.B.; Cook, I.M.; Scott, L.J.

    1993-11-01

    A systematic chemical screening study was conducted on selected anionic-nonionic and nonionic-nonionic systems. The objective of the study was to evaluate and determine combinations of these surfactants that would exhibit favorable phase behavior and solubilization capacity. The effects of different parameters including (a) salinity, (b) temperature, (c) alkane carbon number, (c) hydrophilic/lipophilic balance (HLB) of nonionic component, and (d) type of surfactant on the behavior of the overall chemical system were evaluated. The current work was conducted using a series of ethoxylated nonionic surfactants in combinations of several anionic systems with various hydrocarbons. Efforts to correlate the behavior of these mixed systems led to the development of several models for the chemical systems tested. The models were used to compare the different systems and provided some guidelines for formulating them to account for variations in salinity, oil hydrocarbon number, and temperature. The models were also evaluated to determine conformance with the results from experimental measurements. The models provided good agreement with experimental results. X-ray computed tomography (CT) was used to study fluid distributions during chemical enhanced oil recovery experiments. CT-monitored corefloods were conducted to examine the effect of changing surfactant slug size injection on oil bank formation and propagation. Reducing surfactant slug size resulted in lower total oil production. Oil recovery results, however, did not correlate with slug size for the low-concentration, alkaline, mixed surfactant system used in these tests. The CT measurements showed that polymer mobility control and core features also affected the overall oil recovery results.

  11. Switchable Surfactants

    National Research Council Canada - National Science Library

    Yingxin Liu; Philip G. Jessop; Michael Cunningham; Charles A. Eckert; Charles L. Liotta

    2006-01-01

    .... We report that long-chain alkyl amidine compounds can be reversibly transformed into charged surfactants by exposure to an atmosphere of carbon dioxide, thereby stabilizing water/alkane emulsions...

  12. INTRODUCED LAND SNAILS AND SLUGS IN COLOMBIA.

    Science.gov (United States)

    Hausdorf, BERNHARD

    2002-05-01

    Twelve species of introduced land molluscs, including seven slug species, have been found in the cold zone above 2000 m altitude in the Departamentos Cundinamarca and Boyacá, and the Distrito Especial in Colombia. The introduced land molluscs remain generally restricted to disturbed environments, from which native species are often absent. Most recorded species originated from Europe. Deroceras laeve has been present in Colombia for more than a century, whereas the other species are probably more recent introductions. The records of Boettgerilla pallens, which is indigenous to the Caucasus and has spread over Europe only during the last decades, demonstrates that the process of introduction of alien molluscs is continuing.

  13. Persurf, a new method to improve surfactant delivery: a study in surfactant depleted rats.

    Directory of Open Access Journals (Sweden)

    Wolfram Burkhardt

    Full Text Available PURPOSE: Exogenous surfactant is not very effective in adults with ARDS, since surfactant does not reach atelectatic alveoli. Perfluorocarbons (PFC can recruit atelectatic areas but do not replace impaired endogenous surfactant. A surfactant-PFC-mixture could combine benefits of both therapies. The aim of the proof-of-principal-study was to produce a PFC-in-surfactant emulsion (Persurf and to test in surfactant depleted Wistar rats whether Persurf achieves I. a more homogenous pulmonary distribution and II. a more homogenous recruitment of alveoli when compared with surfactant or PFC alone. METHODS: Three different PFC were mixed with surfactant and phospholipid concentration in the emulsion was measured. After surfactant depletion, animals either received 30 ml/kg of PF5080, 100 mg/kg of stained (green dye Curosurf™ or 30 ml/kg of Persurf. Lungs were fixated after 1 hour of ventilation and alveolar aeration and surfactant distribution was estimated by a stereological approach. RESULTS: Persurf contained 3 mg/ml phospholipids and was stable for more than 48 hours. Persurf-administration improved oxygenation. Histological evaluation revealed a more homogenous surfactant distribution and alveolar inflation when compared with surfactant treated animals. CONCLUSIONS: In surfactant depleted rats administration of PFC-in-surfactant emulsion leads to a more homogenous distribution and aeration of the lung than surfactant alone.

  14. Slug tests in the presence of background head trends.

    Science.gov (United States)

    Ostendorf, David W; DeGroot, Don J

    2010-01-01

    We extend Bouwer and Rice (1976) slug test theory to incorporate background head trends that may be important in incompressible material of low permeability k. The extension, which features a convolution integral of the background head, is closed form for linear trends. A sensitivity study suggests that a rising background head can diminish the head changes associated with a slug-out test and underestimate k if it is ignored, as does falling background trend with a slug-in test. A falling background head can reinforce slug-in test head change and, if ignored, can overestimate k, as does a rising background head with a slug-out test. The simple extension is verified by field tests in glacial till and stratified drift deposits in eastern Massachusetts.

  15. SLUG: A New Way to Stochastically Light Up Galaxies

    Science.gov (United States)

    Fumagalli, M.; da Silva, R.; Krumholz, M.; Bigiel, F.

    2011-06-01

    We present SLUG, a new code to "Stochastically Light Up Galaxies". SLUG populates star clusters by randomly drawing stars from an initial mass function (IMF) and then following their time evolution with stellar models and an observationally-motivated prescription for cluster disruption. For a choice of star formation history, metallicity, and IMF, SLUG outputs synthetic photometry for clusters and field stars with a proper treatment of stochastic star formation. SLUG generates realistic distributions of star clusters, demonstrating the range of properties that result from finite sampling of an IMF and a random distribution of ages. The simulated data sets provide a quantitative means to address open problems in studies of star formation in galaxies and clusters, such as a test for IMF variations that are suggested by the systematic deficiency in the Hα/UV ratio in outer disks or in dwarf galaxies. SLUG will be made publicly available through the website: http://sites.google.com/site/runslug/.

  16. Natural aging of multilayer films containing hydrophobically modified poly(acrylate)s or their complexes with surfactants

    Science.gov (United States)

    Gîfu, Ioana Cătălina; Maxim, Monica Elisabeta; Iovescu, Alina; Aricov, Ludmila; Simion, Elena Livia; Leontieş, Anca Ruxandra; Anastasescu, Mihai; Munteanu, Cornel; Anghel, Dan-Florin

    2017-08-01

    The paper reports the natural aging of polyelectrolyte multilayers containing sodium hydrophobically modified poly(acrylates) (PACnNa, n = 10 and 18) or complexes of PACnNa with alkyltrimethylammonium bromides (CxTAB, x = 10, 12, 14, 18) and poly(diallyldimethylammonium chloride) (PDADMAC). Wettability, thickness and surface morphology of aged multilayers are compared with those of freshly made. Contact angle (CA) increases with the alkyl chain length of the PACnNa and of the CxTAB in the complex with PACnNa. Wettability measurements unveil that only five bilayers of alternatively deposited PAC18Na-C18TAB and PDADMAC reach in 12 months the same CA as sixty freshly prepared bilayers. The PDADMAC outer layer gives higher CA and root mean square roughness than the negatively terminated multilayers. The results are significant for gaining new insight into the underlying mechanism of multilayers aging, saving materials, and improving the surface coatings for long term preservation.

  17. A novel, fast responding, low noise potentiometric sensor containing a carbon-based polymeric membrane for measuring surfactants in industrial and environmental applications.

    Science.gov (United States)

    Samardžić, Mirela; Galović, Olivera; Hajduković, Mateja; Sak-Bosnar, Milan

    2017-01-01

    A new high-sensitivity potentiometric sensor for anionic surfactants was fabricated using the dimethyldioctadecylammonium-tetraphenylborate (DDA-TPB) ion associate as an ionophore that was incorporated into a liquid PVC membrane. Carbon powder was used for immobilization of the ionophore in the membrane, thus significantly reducing its ohmic resistance and reducing its signal drift. The sensor exhibits a sub-Nernstian response for both dodecylbenzenesulfonate (DBS) and dodecyl sulfate (DS) in H2O (55.3 and 58.5mV/decade of activity, respectively) in a range between 3.2×10(-7) and 4.6×10(-3)M for DS and 2.5×10(-7) and 1.2×10(-3)M for DBS. The sensor also exhibited a sub-Nernstian response for DS and DBS in 10mM Na2SO4 (55.4 and 57.7mV/decade of activity, respectively) between 2.5×10(-7) and 4.6×10(-3)M for DS and 1.5×10(-7) and 8.8×10(-4)M for DBS. The detection limits for DS and DBS in H2O were 2.5×10(-7) and 2.0×10(-7) M and in 10mM Na2SO4 the detection limits were 2.5×10(-7) and 1.2×10(-7) M, respectively. The response time of the sensor was less than 5s for changes at higher concentration levels (above 1×10(-4)M) in both water and 10mM Na2SO4. At lower concentrations (below 1×10(-5)M) the response times were 8 and 6s in water and 10mM Na2SO4, respectively. The signal drift of the sensor was 1.2mV/hour. The new carbon-based sensor exhibited excellent selectivity performance for DS over almost all of the anions commonly present in commercial formulations and it was successfully employed as an end-point detector in potentiometric titrations of anionic surfactants in a pH range from 3 to 12. Three-component mixtures containing sodium alkanesulfonate (C10, C12 and C14) were successfully differentially titrated.

  18. Gas-Liquid Slug Flow in Microchannels

    Science.gov (United States)

    Guenther, Axel; de Mas, Nuria; Jhunjhunwala, Manish; Schmidt, Martin A.; Jensen, Klavs F.

    2003-11-01

    Slug flow is not only an attractive regime for conducting gas-liquid reactions in microchemical systems. It also provides a normal velocity that enhances liquid mixing for high Peclet number flows, e.g. for particle synthesis. We previously extended the flow regime diagrams initially obtained for micro heat-exchangers to the liquid deficient conditions relevant to microreactors. We use silicon-based single microchannels with rectangular and triangular cross-section and hydraulic diameters of 40-400 microns that are capped with Pyrex to provide for optical access. Ethanol, water, toluene, and nitrogen are the working fluids. Superficial velocities are varied between 0.01 and 10 m/s for the gas and 0.001 and 1 m/s for the liquid with corresponding Capillary and Bond numbers between 0.001 and 0.01. We complement pulsed-laser fluorescence microscopy and confocal scanning microscopy with a non-intrusive optical sensor to monitor the transient flow at sampling rates of 10 kHz. Interfacial area, void fraction, slug velocity U_s, and the transversal velocity component introduced by internal circulation in the liquid are determined. For comparable Peclet numbers, the transverse velocity between channel wall and center is lO0.1 U_s and allows for shorter mixing lengths than reported for micromixers with patterned walls. Gas and liquid are completely separated on-chip subsequent to the mixing step.

  19. Chemical modification of a plant origin biomass using cationic surfactant ABDAC and the biosorptive decolorization of RR45 containing solutions.

    Science.gov (United States)

    Akar, Tamer; Ozkara, Esra; Celik, Sema; Turkyilmaz, Serpil; Akar, Sibel Tunali

    2013-01-01

    This study focused on the improvement of the decolorization potential of biomass derived from Pyracantha coccinea. Alkyl benyzldimethyl ammonium chloride (ABDAC) was used as modification agent. Batch mode decolorization potential of modified biosorbent was explored at different operating conditions. ABDAC modification significantly increased the biosorption yield to 97.27%, which was 3.88 times higher than that of natural biomass. The prepared biosorbent was effectively used for the decolorization of Reactive Red 45 contaminated solutions after the optimization of biosorption conditions. The non-linear regression analysis was used to evaluate the isotherm and kinetic model parameters. Process followed the Langmuir isotherm model and the highest monolayer capacity of 152.49 mg g(-1) was obtained with a small amount of modified biosorbent. Kinetic studies indicated fast decolorization rate of the process following the pseudo-first-order model. Biosorption performance of the prepared biosorbent was tested in RR45 containing real wastewater sample. The possible dye biosorbent interactions in the biosorption process were explored by zeta potential, scanning electron microscobe and FTIR analysis.

  20. Two-phase slug flow in vertical and inclined tubes

    Institute of Scientific and Technical Information of China (English)

    1996-01-01

    Gas-liquid slug flow is investigated experimentally in vertical and inclined tubes.The non-invasive measuremnts of the gas-liquid slug flow are taken by using the EKTAPRO 1000 High Speed Motion Analyzer.The information on the velocity of the Talyor bubble,the size distribution of the dispersed bubbles in the liquid slugs and some characteristics of the liquid film around the Taylor bubble are obtained.The experimental results are in good agreement with the available data.

  1. 阳离子表面活性剂处理油田含聚合物废水%Treatment of Polymer-containing Oilfield Wastewater Using Cationic Surfactant

    Institute of Scientific and Technical Information of China (English)

    甘二勇; 段明; 陈晨; 方申文; 张健

    2012-01-01

    以7种常见的阳离子表面活性剂为絮凝剂,考察对海上某油田含聚合物废水的处理效果.实验结果表明:一定浓度时,十四烷基三甲基溴化铵和十六烷基三甲基溴化铵有很好的絮凝效果:阳离子季铵盐表面活性剂加入到含聚合物废水中后,先会与连续水相中的水解聚丙烯酰胺(HPAM)发生静电中和作用,剩余的表面活性剂扩散至油水界面与界面处HPAM作用后破坏HPAM对油滴的稳定作用,从而达到絮凝效果;阳离子表面活性剂的加入量与含聚合物废水中HPAM的浓度密切相关.%The polymer-containing wastewater in an offshore oilfield was treated using 7 kinds of common cationic surfactants as flocculents. The experimental results show that: Tetradecyl trimethyl ammonium bromide and cetyl trimethyl ammonium bromide with certain concentration have perfect flocculation effects; After the cationic surfactant is added into the polymer-containing wastewater, the electrostatic neutralization reaction will occur between it and hydrolyzed polyacrylamide(HPAM) in the continuous water phase firstly, then the rest of the surfactant will diffuse to the oil-water interface and react with HPAM located in the oil-water interface so as to destroy the effect of HPAM on oil droplet stabilization and realize the flocculation; There is a close relationship between the dosage of cationc surfactant and the concentration of HPAM in the polymer-containing wastewater.

  2. Slug control system; Sistema de controle de golfadas

    Energy Technology Data Exchange (ETDEWEB)

    Borges Filho, Alvaro de Miranda; Meira, Marco Antonio Alves de; Vaz, Celio Eduardo Martins [PETROBRAS, Macae, RJ (Brazil). Unidade de Negocios da Bacia de Campos

    2004-07-01

    Due to the characteristics of flow, gas can separate from oil in the pipelines and risers that link subsea manifolds to production offshore platforms, forming liquid and gas slugs in the production separator. Liquid slugs can cause overflow in the separators. Gas slugs can cause burning in the flare due to the limitation in the turbo-compressors acceleration. In both cases the consequences are loss of production or shut-downs. This paper presents a Slug Control System designed to attenuate severe gas and liquid flow variations. The system consist of a control valve installed in the separator inlet, transmitters, a controller, control algorithm and a monitoring station. This system is operating since October 2003 in a production offshore platform, in Campus Basin, Brazil, with excellent results, reducing the gas burning in 45% without oil production loss. (author)

  3. The potential for slug control with ferric phosphate

    OpenAIRE

    Horgan, A R

    2006-01-01

    Slug and snail damage, especially on young plants can mean serious economic loss for growers. Organic growers have in the past had few, if any, effective products to use for their control. Now ferric phosphate has recently gained organic status from the Organic Farmers and Growers organisation. Its unique mode of action, environmental profile and effectiveness against a range of slug and snail species will make this a first choice for all organic growers. The eventual breakdown components iro...

  4. Fully developed turbulence in slugs of pipe flows

    Science.gov (United States)

    Cerbus, Rory; Liu, Chien-Chia; Sakakibara, Jun; Gioia, Gustavo; Chakraborty, Pinaki

    2015-11-01

    Despite over a century of research, transition to turbulence in pipe flows remains a mystery. In theory the flow remains laminar for arbitrarily large Reynolds number, Re. In practice, however, the flow transitions to turbulence at a finite Re whose value depends on the disturbance, natural or artificial, in the experimental setup. The flow remains in the transition state for a range of Re ~ 0 (1000) ; for larger Re the flow becomes fully developed. The transition state for Re > 3000 consists of axially segregated regions of laminar and turbulent patches. These turbulent patches, known as slugs, grow as they move downstream. Their lengths span anywhere between a few pipe diameters to the whole length of the pipe. Here we report Stereo Particle Image Velocimetry measurements in the cross-section of the slugs. Notwithstanding the continuous growth of the slugs, we find that the mean velocity and stress profiles in the slugs are indistinguishable from that of statistically-stationary fully-developed turbulent flows. Our results are independent of the length of the slugs. We contrast our results with the well-known work of Wygnanski & Champagne (1973), whose measurements, we argue, are insufficient to draw a clear conclusion regarding fully developed turbulence in slugs.

  5. Fullerene surfactants and their use in polymer solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Jen, Kwan-Yue; Yip, Hin-Lap; Li, Chang-Zhi

    2015-12-15

    Fullerene surfactant compounds useful as interfacial layer in polymer solar cells to enhance solar cell efficiency. Polymer solar cell including a fullerene surfactant-containing interfacial layer intermediate cathode and active layer.

  6. Different effects of surfactant proteins B and C - implications for development of synthetic surfactants.

    Science.gov (United States)

    Curstedt, Tore; Johansson, Jan

    2010-06-01

    Treatment of premature newborn rabbits with synthetic surfactants containing a surfactant protein C analogue in a simple phospholipid mixture gives similar tidal volumes as treatment with poractant alfa (Curosurf(R)) but ventilation with a positive end-expiratory pressure (PEEP) is needed for this synthetic surfactant to stabilize the alveoli at end-expiration. The effect on lung gas volumes seems to depend on the structure of the peptide since treatment with a synthetic surfactant containing the 21-residue peptide (LysLeu(4))(4)Lys (KL(4)) gives low lung gas volumes in experiments also performed with PEEP. Surfactant preparations containing both surfactant proteins B and C or their analogues prevent alveolar collapse at end-expiration even if ventilated without PEEP. Treatment of premature newborn rabbits with different natural surfactants indicates that both the lipid composition and the proteins are important in order to stabilize the alveoli at end-expiration. Synthetic surfactants containing two peptides may be able to replace natural surfactants within the near future but more trials need to be performed before any conclusion can be drawn about the ideal composition of this new generation of synthetic surfactants.

  7. The effect of surfactant and sonication time on the stability and thermal conductivity of water-based nanofluid containing Mg(OH)2 nanoparticles: An experimental investigation

    DEFF Research Database (Denmark)

    Asadi, Amin; Asadi, Meisam; Siahmargoi, Marzieh

    2017-01-01

    The main objective of the present study was to investigate the effect of surfactant and sonication time on the stability and thermal conductivity of Mg (OH)2-water nanofluid over the different solid concentrations (0.1, 0.2, 0.4, 0.8, 1, 1.5, and 2%) and temperatures (25, 30, 35, 40, 45, 50 °C...... of the nanofluid. The results of Zeta potential analysis indicated that CTAB surfactant shows the best impact on the stability of the nanofluid applying 30-min sonication. Furthermore, it is found that the relative thermal conductivity of the studied nanofluid relatively increased as the solid concentration...... and temperature increased. The maximum increase in thermal conductivity took place at the solid concentration of 2% and temperature of 50 °C by approximately 28%. Moreover, in order to investigate the effect of sonication time of thermal properties of the nanofluid, the relative thermal conductivity...

  8. Slug down-regulation by RNA interference inhibits invasion growth in human esophageal squamous cell carcinoma

    Directory of Open Access Journals (Sweden)

    Zhang Shaoyan

    2011-05-01

    Full Text Available Abstract Background Esophageal squamous cell carcinoma (ESCC is one of the most aggressive carcinomas of the gastrointestinal tract. We assessed the relevance of Slug in measuring the invasive potential of ESCC cells in vitro and in vivo in immunodeficient mice. Methods We utilized RNA interference to knockdown Slug gene expression, and effects on survival and invasive carcinoma were evaluated using a Boyden chamber transwell assay in vitro. We evaluated the effect of Slug siRNA-transfection and Slug cDNA-transfection on E-cadherin and Bcl-2 expression in ESCC cells. A pseudometastatic model of ESCC in immunodeficient mice was used to assess the effects of Slug siRNA transfection on tumor metastasis development. Results The EC109 cell line was transfected with Slug-siRNA to knockdown Slug expression. The TE13 cell line was transfected with Slug-cDNA to increase Slug expression. EC109 and TE13 cell lines were tested for the expression of apoptosis-related genes bcl-2 and metastasis-related gene E-cadherin identified previously as Slug targets. Bcl-2 expression was increased and E-cadherin was decreased in Slug siRNA-transfected EC109 cells. Bcl-2 expression was increased and E-cadherin was decreased in Slug cDNA-transfected TE13 cells. Invasion of Slug siRNA-transfected EC109 cells was reduced and apoptosis was increased whereas invasion was greater in Slug cDNA-transfected cells. Animals injected with Slug siRNA-transfected EC109 cells exhihited fewer seeded nodes and demonstrated more apoptosis. Conclusions Slug down-regulation promotes cell apoptosis and decreases invasion capability in vitro and in vivo. Slug inhibition may represent a novel strategy for treatment of metastatic ESCC.

  9. An invasive slug exploits an ant-seed dispersal mutualism.

    Science.gov (United States)

    Meadley Dunphy, Shannon A; Prior, Kirsten M; Frederickson, Megan E

    2016-05-01

    Plant-animal mutualisms, such as seed dispersal, are often vulnerable to disruption by invasive species. Here, we show for the first time how a non-ant invasive species negatively affects seed dispersal by ants. We examined the effects of several animal species that co-occur in a temperate deciduous forest-including native and invasive seed-dispersing ants (Aphaenogaster rudis and Myrmica rubra, respectively), an invasive slug (Arion subfuscus), and native rodents-on a native myrmecochorous plant, Asarum canadense. We experimentally manipulated ant, slug, and rodent access to seed depots and measured seed removal. We also video-recorded depots to determine which other taxa interact with seeds. We found that A. rudis was the main disperser of seeds and that A. subfuscus consumed elaiosomes without dispersing seeds. Rodent visitation was rare, and rodent exclusion had no significant effect on seed or elaiosome removal. We then used data obtained from laboratory and field mesocosm experiments to determine how elaiosome robbing by A. subfuscus affects seed dispersal by A. rudis and M. rubra. We found that elaiosome robbing by slugs reduced seed dispersal by ants, especially in mesocosms with A. rudis, which picks up seeds more slowly than M. rubra. Taken together, our results show that elaiosome robbing by an invasive slug reduces seed dispersal by ants, suggesting that invasive slugs can have profound negative effects on seed dispersal mutualisms.

  10. Silicone antifoam performance enhancement by nonionic surfactants in potato medium.

    Science.gov (United States)

    Christiano, Steven P; Fey, Kenneth C

    2003-01-01

    The ability of a silicone antifoam to retard foaming in a liquor prepared from potatoes is enhanced by the addition of ethoxylated nonionic surfactants. The enhancement is non-linear for surfactant concentration, with all 12 surfactants tested possessing a concentration at which foam heights strongly diminish, referred to as the surfactant critical antifoaming concentration (SCAFC). SCAFCs vary between surfactants, with lower values indicating better mass efficiency of antifoaming enhancement. SCAFCs decrease with degree of ethoxylation and decrease with the hydrophilic-lipophilic balance for ethoxylated nonionic surfactants. Surfactant addition produces a mixed water-surface layer containing surfactant and surface-active components in the potato medium. Surface tension reduction does not correlate well with antifoam performance enhancement. A model is proposed where surfactant adsorption promotes desorption of surface-active potato medium components from the water surface. At the SCAFC, desorption is not complete, yet the rate of bubble rupture is sufficiently enhanced to provide excellent foam control.

  11. Modelling of slug dissipation and generation in a hilly-terrain pipeline

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, H.-Q.; El-Safran, E.M.; Jayawardena, S.S.; Redus, C.L.; Brill, J.P. [University of Tulsa (United States). Dept. of Petroleum Engineering

    2000-07-01

    Hilly-terrain pipelines consist of interconnected horizontal, uphill and downhill sections. Slug flow experiences a transition from one state to another as the pipe inclination angle changes. Normally, slugs dissipate if the upward inclination becomes smaller or the downward inclination becomes larger, and slug generation occurs vice versa. Appropriate prediction of the slug characteristics is crucial for the design of pipeline and downstream facilities. In this study, slug dissipation and generation in a valley pipeline configuration (horizontal-downhill-uphill-horizontal) were modeled by use of the method proposed by Zhang et al. The method was developed from the unsteady continuity and momentum equations for slug flow by considering the entire film zone as the control volume. Computed results are compared with experimental measurements at different gas-liquid flow rate combinations. Good agreement is observed for the change of slug body length to slug unit length ratio. (author)

  12. Simulation of horizontal slug-flow pneumatic conveying with kinetic theory

    Institute of Scientific and Technical Information of China (English)

    GU Zhengmeng; GUO Liejin

    2007-01-01

    Wavelike slug-flow is a representative flow type in horizontal pneumatic conveying.Kinetic theory was introduced to establish a 3D kinetic numerical model for wavelike slug gas-solid flow in this paper.Wavelike motion of particulate slugs in horizontal pipes was numerically investigated.The formation and motion process of slugs and settled layer were simulated.The characteristics of the flow,such as pressure drop,air velocity distribution,slug length and settled layer thickness,and the detailed changing characteristics of slug length and settled layer thickness with air velocity were obtained.The results indicate that kinetic theory can represent the physical characteristics of the non-suspension dense phase flow of wavelike slug pneumatic conveying.The experiment in this paper introduced a new idea for the numerical calculation of slug-flow pneumatic conveying.

  13. Challenges in Slug Modeling and Control for Offshore Oil and Gas Productions: A Review Study

    DEFF Research Database (Denmark)

    Pedersen, Simon; Løhndorf, Petar Durdevic; Yang, Zhenyu

    2017-01-01

    the state-of-the-art related to analysis, detection, dynamical modeling and elimination of the slug within the offshore oil & gas Exploration and Production (E&P) processes. Modeling of slugging flow has been used to investigate the slug characteristics and for design of anti-slug control as well, however...... most models require specific facility and operating data which, unfortunately, often is not available from most offshore installations. Anti-slug control have been investigated for several decades in oil & gas industry, but many of these existing methods suffer the consequent risk of simultaneously...... reducing the oil & gas production. This paper concludes that slug is a well defined phenomenon, but even though it has been investigated for several decades the current anti-slug control methods still have problems related to robustness. It is predicted that slug-induced challenges will be even more severe...

  14. A new general pressure-analysis procedure for slug tests

    Energy Technology Data Exchange (ETDEWEB)

    Peres, A.M.M.; Onur, M.; Reynolds, A.C. (Univ. of Tulsa, OK (United States))

    1993-12-01

    A new analysis procedure for determining formation flow capacity and skin factor from slug-test data is presented. The procedure arises from exact deconvolution equations that convert measured slug-test pressure data into equivalent pressure and pressure-derivative responses that would be obtained if the well were produced at a constant surface flow rate. The converted data then can be analyzed by use of existing wellbore-storage and skin type curves for the particular reservoir or well model represented by the field data. For cases where the slug test is short, the authors show that flow rate convolution can be incorporated to improve analysis reliability. The analysis procedures do not require direct knowledge of the sandface flow rate.

  15. Synthesis, CMC Determination, Antimicrobial Activity and Nucleic Acid Binding of A Surfactant Copper(II) Complex Containing Phenanthroline and Alanine Schiff-Base.

    Science.gov (United States)

    Nagaraj, Karuppiah; Sakthinathan, Subramanian; Arunachalam, Sankaralingam

    2014-03-01

    A new water-soluble surfactant copper(II) complex [Cu(sal-ala)(phen)(DA)] (sal-ala = salicylalanine, phen = 1,10-phenanthroline, DA = dodecylamine), has been synthesized and characterized by physico-chemical and spectroscopic methods. The critical micelle concentration (CMC) values of this surfactant-copper(II) complex in aqueous solution were obtained from conductance measurements. Specific conductivity data (at 303, 308, 313. 318 and 323 K) served for the evaluation of the temperature-dependent CMC and the thermodynamics of micellization (ΔG(0)m, ΔH(0)m and ΔS(0)m). The interaction of this complex with nucleic acids (DNA and RNA) has been explored by using electronic absorption spectral titration, competitive binding experiment, cyclic voltammetry, circular dichroism (CD) spectra, and viscosity measurements. Electronic absorption studies have revealed that the complex can bind to nucleic acids by the intercalative binding mode which has been verified by viscosity measurements. The DNA binding constants have also been calculated (Kb = 1.2 × 10(5) M(-1) for DNA and Kb = 1.6 × 10(5) M(-1) for RNA). Competitive binding study with ethidium bromide (EB) showed that the complex exhibits the ability to displace the DNA-bound-EB indicating that the complex binds to DNA in strong competition with EB for the intercalative binding site. The presence of hydrophobic ligands, alanine Schiff-base, phenanthroline and long aliphatic chain amine in the complex were responsible for this strong intercalative binding. The surfactant-copper (II) complex was screened for its antibacterial and antifungal activities against various microorganisms. The results were compared with the standard drugs, amikacin(antibacterial) and ketokonazole(antifungal).

  16. O/W emulsions stabilised by both low molecular weight surfactants and colloidal particles: The effect of surfactant type and concentration.

    Science.gov (United States)

    Pichot, R; Spyropoulos, F; Norton, I T

    2010-12-01

    The stability against coalescence of O/W emulsions in the presence of both surfactants and colloidal particles was investigated. In particular the effect of the surfactant type and concentration in these emulsifier mixtures on the O/W emulsions' stability was studied. Two types of surfactants were selected; those that have the ability to stabilise O/W emulsions on their own (O/W surfactants) and those that cannot (W/O surfactants). Tween 60 and Sodium Caseinate were selected as the O/W surfactants and lecithin as the W/O surfactant. Oil-in-water emulsions prepared with both particles and any of the three surfactants were stable against coalescence but, depending on the type of surfactant, the behaviour of the systems was found to depend on surfactant concentration. The droplet sizes of emulsions stabilised by mixed emulsifier systems containing low concentrations of O/W surfactants (Tween 60 or Sodium Caseinate) were smaller than those solely stabilised by either the surfactant or particles alone. At intermediate O/W surfactants concentrations, the droplet sizes of the emulsions increased. Further increases in the O/W surfactants' concentration, resulted in the complete removal of particles from the interface with the system now behaving as a surfactant-only stabilised emulsion. The behaviour of emulsions stabilised by emulsifier mixtures containing W/O surfactants was not dependent on the concentration of surfactant: no removal of particles was observed. Copyright © 2010 Elsevier Inc. All rights reserved.

  17. Slug to churn transition analysis using wire-mesh sensor

    Science.gov (United States)

    H. F. Velasco, P.; Ortiz-Vidal, L. E.; Rocha, D. M.; Rodriguez, O. M. H.

    2016-06-01

    A comparison between some theoretical slug to churn flow-pattern transition models and experimental data is performed. The flow-pattern database considers vertical upward air-water flow at standard temperature and pressure for 50 mm and 32 mm ID pipes. A briefly description of the models and its phenomenology is presented. In general, the performance of the transition models is poor. We found that new experimental studies describing objectively both stable and unstable slug flow-pattern are required. In this sense, the Wire Mesh Sensor (WMS) can assist to that aim. The potential of the WMS is outlined.

  18. Slug promotes survival during metastasis through suppression of Puma-mediated apoptosis.

    Science.gov (United States)

    Kim, Seaho; Yao, Jiahong; Suyama, Kimita; Qian, Xia; Qian, Bin-Zhi; Bandyopadhyay, Sanmay; Loudig, Olivier; De Leon-Rodriguez, Carlos; Zhou, Zhen Ni; Segall, Jeffrey; Macian, Fernando; Norton, Larry; Hazan, Rachel B

    2014-07-15

    Tumor cells must overcome apoptosis to survive throughout metastatic dissemination and distal organ colonization. Here, we show in the Polyoma Middle T mammary tumor model that N-cadherin (Cdh2) expression causes Slug (Snai2) upregulation, which in turn promotes carcinoma cell survival. Slug was dramatically upregulated in metastases relative to primary tumors. Consistent with a role in metastasis, Slug knockdown in carcinoma cells suppressed lung colonization by decreasing cell survival at metastatic sites, but had no effect on tumor cell invasion or extravasation. In support of this idea, Slug inhibition by shRNA sensitized tumor cells to apoptosis by DNA damage, resulting in caspase-3 and PARP cleavage. The prosurvival effect of Slug was found to be caused by direct repression of the proapoptotic gene, Puma (Bbc3), by Slug. Consistent with a pivotal role for a Slug-Puma axis in metastasis, inhibition of Puma by RNA interference in Slug-knockdown cells rescued lung colonization, whereas Puma overexpression in control tumor cells suppressed lung metastasis. The survival function of the Slug-Puma axis was confirmed in human breast cancer cells, where Slug knockdown increased Puma expression and inhibited lung colonization. This study demonstrates a pivotal role for Slug in carcinoma cell survival, implying that disruption of the Slug-Puma axis may impinge on the survival of metastatic cells.

  19. Is a combination of different natural substances suitable for slug (Arion spp.) control?

    Energy Technology Data Exchange (ETDEWEB)

    Laznik, Ž.; Trdan, S.

    2016-11-01

    In a laboratory study we investigated the contact and barrier efficacy of different natural substances (wood ash, sawdust, hydrated lime, and diatomaceous earth) against slugs of the genus Arion, an important agricultural pest. Natural substances were tested individually and in combination with each other. The experiment was carried out in plastic petri dishes and in glass insectaria. Moistened tampons and fresh leaves of lettuce were placed into both experimental arenas. The slugs were starved for 48 hours prior to the experiment. Six categories of behaviour were identified for slugs in the presence of the natural substances: (1) slug survived the experiment, (2) slug died during the experiment, (3) slug crossed the barrier, (4) slug did not cross the barrier, (5) slug fed on the lettuce, and (6) slug did not feed on the lettuce. The effect of different treatments (natural substances) was significant. The results of our study have shown that hydrated lime had the best contact efficacy on slugs (the mortality of slugs was 100%), both individually and in combination with other substances. The treatments with hydrated lime also proved to be the most efficient barrier preventing slugs from feeding on lettuce. Hydrated lime shows great potential in Arion control in our investigation; however, further research is needed to investigate the practical value (how to avoid the problem when the substance becomes wet), safety and economics of hydrated lime used in this way. (Author)

  20. Internal Representation and Memory Formation of Odor Preference Based on Oscillatory Activities in a Terrestrial Slug

    Science.gov (United States)

    Sekiguchi, Tatsuhiko; Furudate, Hiroyuki; Kimura, Tetsuya

    2010-01-01

    The terrestrial slug "Limax" exhibits a highly developed ability to learn odors with a small nervous system. When a fluorescent dye, Lucifer Yellow (LY), is injected into the slug's body cavity after odor-taste associative conditioning, a group of neurons in the procerebral (PC) lobe, an olfactory center of the slug, is labeled by LY. We examined…

  1. Solubilization of Hydrophobic Dyes in Surfactant Solutions

    Directory of Open Access Journals (Sweden)

    Ali Reza Tehrani-Bagha

    2013-02-01

    Full Text Available In this paper, the use of surfactants for solubilization of hydrophobic organic dyes (mainly solvent and disperse dyes has been reviewed. The effect of parameters such as the chemical structures of the surfactant and the dye, addition of salt and of polyelectrolytes, pH, and temperature on dye solubilization has been discussed. Surfactant self-assemble into micelles in aqueous solution and below the concentration where this occurs—the critical micelle concentration (CMC—there is no solubilization. Above the CMC, the amount of solubilized dye increases linearly with the increase in surfactant concentration. It is demonstrated that different surfactants work best for different dyes. In general, nonionic surfactants have higher solubilization power than anionic and cationic surfactants. It is likely that the reason for the good performance of nonionic surfactants is that they allow dyes to be accommodated not only in the inner, hydrocarbon part of the micelle but also in the headgroup shell. It is demonstrated that the location of a dye in a surfactant micelle can be assessed from the absorption spectrum of the dye-containing micellar solution.

  2. SLUG promotes prostate cancer cell migration and invasion via CXCR4/CXCL12 axis

    Directory of Open Access Journals (Sweden)

    Uygur Berna

    2011-11-01

    Full Text Available Abstract Background SLUG is a zinc-finger transcription factor of the Snail/Slug zinc-finger family that plays a role in migration and invasion of tumor cells. Mechanisms by which SLUG promotes migration and invasion in prostate cancers remain elusive. Methods Expression level of CXCR4 and CXCL12 was examined by Western blot, RT-PCR, and qPCR analyses. Forced expression of SLUG was mediated by retroviruses, and SLUG and CXCL12 was downregulated by shRNAs-expressing lentiviruses. Migration and invasion of prostate cancer were measured by scratch-wound assay and invasion assay, respectively. Research We demonstrated that forced expression of SLUG elevated CXCR4 and CXCL12 expression in human prostate cancer cell lines PC3, DU145, 22RV1, and LNCaP; conversely, reduced expression of SLUG by shRNA downregulated CXCR4 and CXCL12 expression at RNA and protein levels in prostate cancer cells. Furthermore, ectopic expression of SLUG increased MMP9 expression and activity in PC3, 22RV1, and DU-145 cells, and SLUG knockdown by shRNA downregulated MMP9 expression. We showed that CXCL12 is required for SLUG-mediated MMP9 expression in prostate cancer cells. Moreover, we found that migration and invasion of prostate cancer cells was increased by ectopic expression of SLUG and decreased by SLUG knockdown. Notably, knockdown of CXCL12 by shRNA impaired SLUG-mediated migration and invasion in prostate cancer cells. Lastly, our data suggest that CXCL12 and SLUG regulate migration and invasion of prostate cancer cells independent of cell growth. Conclusion We provide the first compelling evidence that upregulation of autocrine CXCL12 is a major mechanism underlying SLUG-mediated migration and invasion of prostate cancer cells. Our findings suggest that CXCL12 is a therapeutic target for prostate cancer metastasis.

  3. Biomimicry of surfactant protein C.

    Science.gov (United States)

    Brown, Nathan J; Johansson, Jan; Barron, Annelise E

    2008-10-01

    Since the widespread use of exogenous lung surfactant to treat neonatal respiratory distress syndrome, premature infant survival and respiratory morbidity have dramatically improved. Despite the effectiveness of the animal-derived surfactant preparations, there still remain some concerns and difficulties associated with their use. This has prompted investigation into the creation of synthetic surfactant preparations. However, to date, no clinically used synthetic formulation is as effective as the natural material. This is largely because the previous synthetic formulations lacked analogues of the hydrophobic proteins of the lung surfactant system, SP-B and SP-C, which are critical functional constituents. As a result, recent investigation has turned toward the development of a new generation of synthetic, biomimetic surfactants that contain synthetic phospholipids along with a mimic of the hydrophobic protein portion of lung surfactant. In this Account, we detail our efforts in creating accurate mimics of SP-C for use in a synthetic surfactant replacement therapy. Despite SP-C's seemingly simple structure, the predominantly helical protein is extraordinarily challenging to work with given its extreme hydrophobicity and structural instability, which greatly complicates the creation of an effective SP-C analogue. Drawing inspiration from Nature, two promising biomimetic approaches have led to the creation of rationally designed biopolymers that recapitulate many of SP-C's molecular features. The first approach utilizes detailed SP-C structure-activity relationships and amino acid folding propensities to create a peptide-based analogue, SP-C33. In SP-C33, the problematic and metastable polyvaline helix is replaced with a structurally stable polyleucine helix and includes a well-placed positive charge to prevent aggregation. SP-C33 is structurally stable and eliminates the association propensity of the native protein. The second approach follows the same design

  4. Molecular-thermodynamic theory of micellization of multicomponent surfactant mixtures: 2. pH-sensitive surfactants.

    Science.gov (United States)

    Goldsipe, Arthur; Blankschtein, Daniel

    2007-05-22

    In article 1 of this series, we developed a molecular-thermodynamic (MT) theory to model the micellization of mixtures containing an arbitrary number of conventional (pH-insensitive) surfactants. In this article, we extend the MT theory to model mixtures containing a pH-sensitive surfactant. The MT theory was validated by examining mixtures containing both a pH-sensitive surfactant and a conventional surfactant, which effectively behave like ternary surfactant mixtures. We first compared the predicted micellar titration data to experimental micellar titration data that we obtained for varying compositions of mixed micelles containing the pH-sensitive surfactant dodecyldimethylamine oxide (C12DAO) mixed with either a cationic surfactant (dodecyltrimethylammonium bromide, C12TAB), a nonionic surfactant (dodecyl octa(ethylene oxide), C12E8), or an anionic surfactant (sodium dodecyl sulfate, SDS) surfactant. The MT theory accurately modeled the titration behavior of C12DAO mixed with C12E8. However, C12DAO was observed to interact more favorably with SDS and with C12TAB than was predicted by the MT theory. We also compared predictions to data from the literature for mixtures of C12DAO and SDS. Although the pH values of solutions with no added acid were modeled with only qualitative accuracy, the MT theory resulted in quantitatively accurate predictions of solution pH for mixtures containing added acid. In addition, the predicted degree of counterion binding yielded a lower bound to the experimentally measured value. Finally, we predicted the critical micelle concentration (cmc) of solutions of two pH-sensitive surfactants, tetradecyldimethylamine oxide (C14DAO) and hexadecyldimethyl betaine (C16Bet), at varying solution pH and surfactant composition. However, at the pH values considered, the pH sensitivity of C16Bet could be neglected, and it was equivalently modeled as a zwitterionic surfactant. The cmc's predicted using the MT theory agreed well with the experimental

  5. A heat transfer model for slug flow boiling within microchannels

    Science.gov (United States)

    Magnini, Mirco; Thome, John

    2016-11-01

    We propose a novel physics-based model for the fluid mechanics and heat transfer associated with slug flow boiling in horizontal circular microchannels, to update the widely used three-zone model for the design of multi-microchannel evaporators. The flow is modelled as the cyclic passage of a liquid slug, an elongated bubble which traps a thin liquid film against the channel wall, and a dry vapor plug. The capillary flow theory, extended to incorporate evaporation effects, is applied to estimate the bubble velocity along the channel. A liquid film thickness prediction method considering bubble proximity effects, which may limit the radial extension of the film, is included. Theoretical heat transfer models accounting for the thermal inertia of the liquid film and for the recirculating flow within the liquid slug are utilized. The heat transfer model is compared to experimental data taken from three independent studies: 833 slug flow boiling data points covering R134a, R245fa and R236fa and channel diameters from 0.4 mm to 1 mm. The new model predicts more than 80% of the database to within +/- 30 % and it represents an important step toward a complete physics-based modelling of bubble dynamics and heat transfer within microchannels under evaporating flow conditions.

  6. Propylene polymerization in a circulating slugging fluidized bed reactor

    NARCIS (Netherlands)

    Putten, van Inge Cornelia

    2004-01-01

    The work presented in this thesis is concerned with research on the riser of a circulating fluidized bed system for olefin polymerization. In the riser section, fluidization takes place in the transporting slugging mode and polymer particles are produced in the riser in a non-isothermal way. Propert

  7. Modeling cross-hole slug tests in an unconfined aquifer

    CERN Document Server

    Malama, Bwalya; Brauchler, Ralf; Bayer, Peter

    2016-01-01

    A modified version of a published slug test model for unconfined aquifers is applied to cross-hole slug test data collected in field tests conducted at the Widen site in Switzerland. The model accounts for water-table effects using the linearised kinematic condition. The model also accounts for inertial effects in source and observation wells. The primary objective of this work is to demonstrate applicability of this semi-analytical model to multi-well and multi-level pneumatic slug tests. The pneumatic perturbation was applied at discrete intervals in a source well and monitored at discrete vertical intervals in observation wells. The source and observation well pairs were separated by distances of up to 4 m. The analysis yielded vertical profiles of hydraulic conductivity, specific storage, and specific yield at observation well locations. The hydraulic parameter estimates are compared to results from prior pumping and single-well slug tests conducted at the site, as well as to estimates from particle size ...

  8. Modeling cross-hole slug tests in an unconfined aquifer

    Science.gov (United States)

    Malama, Bwalya; Kuhlman, Kristopher L.; Brauchler, Ralf; Bayer, Peter

    2016-09-01

    A modified version of a published slug test model for unconfined aquifers is applied to cross-hole slug test data collected in field tests conducted at the Widen site in Switzerland. The model accounts for water-table effects using the linearized kinematic condition. The model also accounts for inertial effects in source and observation wells. The primary objective of this work is to demonstrate applicability of this semi-analytical model to multi-well and multi-level pneumatic slug tests. The pneumatic perturbation was applied at discrete intervals in a source well and monitored at discrete vertical intervals in observation wells. The source and observation well pairs were separated by distances of up to 4 m. The analysis yielded vertical profiles of hydraulic conductivity, specific storage, and specific yield at observation well locations. The hydraulic parameter estimates are compared to results from prior pumping and single-well slug tests conducted at the site, as well as to estimates from particle size analyses of sediment collected from boreholes during well installation. The results are in general agreement with results from prior tests and are indicative of a sand and gravel aquifer. Sensitivity analysis show that model identification of specific yield is strongest at late-time. However, the usefulness of late-time data is limited due to the low signal-to-noise ratios.

  9. Modelling Morphogenesis: From Single Cells to Crawling Slugs

    NARCIS (Netherlands)

    Savill, N.J.; Hogeweg, P.

    2002-01-01

    We present a three-dimensional hybrid cellular automata (CA)/partial differential equation (PDE) model that allows for the study of morphogenesis in simple cellular systems. We apply the model to the cellular slime mold Dictyostelium discoideum "from single cells to crawling slug". Using simple loca

  10. Simulation of horizontal pipe two-phase slug flows using the two-fluid model

    Energy Technology Data Exchange (ETDEWEB)

    Ortega Malca, Arturo J. [Pontificia Univ. Catolica do Rio de Janeiro, RJ (Brazil). Dept. de Engenharia Mecanica. Nucleo de Simulacao Termohidraulica de Dutos (SIMDUT); Nieckele, Angela O. [Pontificia Univ. Catolica do Rio de Janeiro, RJ (Brazil). Dept. de Engenharia Mecanica

    2005-07-01

    Slug flow occurs in many engineering applications, mainly in the transport of hydrocarbon fluids in pipelines. The intermittency of slug flow causes severe unsteady loading on the pipelines carrying the fluids, which gives rise to design problems. Therefore, it is important to be able to predict the onset and development of slug flow as well as slug characteristics. The present work consists in the simulation of two-phase flow in slug pattern through horizontal pipes using the two-fluid model in its transient and one-dimensional form. The advantage of this model is that the flow field is allowed to develop naturally from a given initial conditions as part of the transient calculation; the slug evolves automatically as a product of the computed flow development. Simulations are then carried out for a large number of flow conditions that lead a slug flow. (author)

  11. 含表面活性剂液膜的去湿特性%Investigation on Dewetting Dynamics of Thin Liquid Film Containing Insoluble Surfactant

    Institute of Scientific and Technical Information of China (English)

    李春曦; 沈雷; 叶学民; 童家麟

    2013-01-01

    针对存在壁面滑移的含非溶性表面活性剂液膜在固体表面的去湿过程,应用基于润滑理论建立的液膜厚度及表面活性剂浓度的演化方程组,采用PDECOL程序对液膜演化历程进行了数值模拟,并分析了各特征参数对去湿特性的影响.结果表明,Marangoni效应对垂直方向上液膜厚度的变化影响微弱,液膜厚度的变化由分离压及毛细力所主导;Marangoni数对最终形成的去湿结构的影响并不显著,减小毛细力数则有助于抑制去湿过程的发展;增大滑移系数可以加速去湿进程,而最终形成的去湿结构明显缩小;增大平衡液膜厚度,液膜表面变形程度减小,液膜厚度逐渐趋于平稳.%Under slip boundary conditions, the dewetting of thin liquid films in the presence of insoluble surfactant monolayer was considered. Coupled nonlinear governing equations for the film thickness and surfactant concentration based on boundary layer theory were employed. The dewetting evolution of films was simulated using PDECOL program and the numerical results were presented, while the effects of characteristic parameters on dewetting process were discussed. The results show that the impact of Marangoni effect on the change rate of films thickness is not significant in vertical direction, the change rate of films thickness is dominated by disjoining pressure and capillary stress. The influence of Marangoni number M on static dewetted structures is not significant, and decreasing capillary number C will suppress the dewetting phenomenon effectively. Increasing slip coefficient β will accelerate the dewetting process and shorten the dewetted structures. Increasing equilibrium film thickness lc will lessen the deformation degree of surface and thereby lead the film thickness to be stabilized.

  12. Palm oil based surfactant products for petroleum industry

    Science.gov (United States)

    Permadi, P.; Fitria, R.; Hambali, E.

    2017-05-01

    In petroleum production process, many problems causing reduced production are found. These include limited oil recovery, wax deposit, asphaltene deposit, sludge deposit, and emulsion problem. Petroleum-based surfactant has been used to overcome these problems. Therefore, innovation to solve these problems using surfactant containing natural materials deserves to be developed. Palm oil-based surfactant is one of the potential alternatives for this. Various types of derivative products of palm oil-based surfactant have been developed by SBRC IPB to be used in handling problems including surfactant flooding, well stimulation, asphaltene dissolver, well cleaning, and wax removal found in oil and gas industry.

  13. Study on the reutilization of clear fracturing flowback fluids in surfactant flooding with additives for Enhanced Oil Recovery (EOR.

    Directory of Open Access Journals (Sweden)

    Caili Dai

    Full Text Available An investigation was conducted to study the reutilization of clear fracturing flowback fluids composed of viscoelastic surfactants (VES with additives in surfactant flooding, making the process more efficient and cost-effective. The clear fracturing flowback fluids were used as surfactant flooding system with the addition of α-olefin sulfonate (AOS for enhanced oil recovery (EOR. The interfacial activity, emulsification activity and oil recovery capability of the recycling system were studied. The interfacial tension (IFT between recycling system and oil can be reduced by 2 orders of magnitude to 10(-3 mN/m, which satisfies the basic demand of surfactant flooding. The oil can be emulsified and dispersed more easily due to the synergetic effect of VES and AOS. The oil-wet surface of quartz can be easily converted to water-wet through adsorption of surfactants (VES/AOS on the surface. Thirteen core plug flooding tests were conducted to investigate the effects of AOS concentrations, slug sizes and slug types of the recycling system on the incremental oil recovery. The investigations prove that reclaiming clear fracturing flowback fluids after fracturing operation and reuse it in surfactant flooding might have less impact on environment and be more economical.

  14. Study on the reutilization of clear fracturing flowback fluids in surfactant flooding with additives for Enhanced Oil Recovery (EOR).

    Science.gov (United States)

    Dai, Caili; Wang, Kai; Liu, Yifei; Fang, Jichao; Zhao, Mingwei

    2014-01-01

    An investigation was conducted to study the reutilization of clear fracturing flowback fluids composed of viscoelastic surfactants (VES) with additives in surfactant flooding, making the process more efficient and cost-effective. The clear fracturing flowback fluids were used as surfactant flooding system with the addition of α-olefin sulfonate (AOS) for enhanced oil recovery (EOR). The interfacial activity, emulsification activity and oil recovery capability of the recycling system were studied. The interfacial tension (IFT) between recycling system and oil can be reduced by 2 orders of magnitude to 10(-3) mN/m, which satisfies the basic demand of surfactant flooding. The oil can be emulsified and dispersed more easily due to the synergetic effect of VES and AOS. The oil-wet surface of quartz can be easily converted to water-wet through adsorption of surfactants (VES/AOS) on the surface. Thirteen core plug flooding tests were conducted to investigate the effects of AOS concentrations, slug sizes and slug types of the recycling system on the incremental oil recovery. The investigations prove that reclaiming clear fracturing flowback fluids after fracturing operation and reuse it in surfactant flooding might have less impact on environment and be more economical.

  15. Experimental investigation of the effect of liquid viscosity on slug flow in small diameter bubble column

    Directory of Open Access Journals (Sweden)

    Azzopardi Barry John

    2012-04-01

    Full Text Available The effect of liquid viscosity on slug flow in a 50 mm diameter bubble column was investigated experimentally using air-silicone oil as operating fluid with silicone oil of viscosities 5, 100, 1000 and 5000 mPa.s. Data was collected using Electrical Capacitance Tomography (ECT, a non-intrusive advanced instrumentation measuring technique and the high Speed Video Camera, through which the slug parameters such as length of Taylor bubbles and liquid slug, void fraction in Taylor bubbles and liquid slug, slug frequency, film thickness and pressure gradient in the slug, were measured and analyzed. The analysis was done using the void fraction time series, probability density function and power spectral density plots. Superficial gas velocities of 0.02≤Ugs≤0.361 m/s were used in the experiment. It was also observed that as viscosity increases, slug frequency, structure velocity, length of liquid slug, void fraction in liquid slug and void fraction in Taylor bubbles decreases; while the length of Taylor bubble, film thickness and pressure gradient in the slug increases.

  16. Role of the Slug Transcription Factor in Chemically-Induced Skin Cancer

    Directory of Open Access Journals (Sweden)

    Kristine von Maltzan

    2016-02-01

    Full Text Available The Slug transcription factor plays an important role in ultraviolet radiation (UVR-induced skin carcinogenesis, particularly in the epithelial-mesenchymal transition (EMT occurring during tumor progression. In the present studies, we investigated the role of Slug in two-stage chemical skin carcinogenesis. Slug and the related transcription factor Snail were expressed at high levels in skin tumors induced by 7,12-dimethylbenz[α]anthracene application followed by 12-O-tetradecanoylphorbol-13-acetate (TPA treatment. TPA-induced transient elevation of Slug and Snail proteins in normal mouse epidermis and studies in Slug transgenic mice indicated that Slug modulates TPA-induced epidermal hyperplasia and cutaneous inflammation. Although Snail family factors have been linked to inflammation via interactions with the cyclooxygenase-2 (COX-2 pathway, a pathway that also plays an important role in skin carcinogenesis, transient TPA induction of Slug and Snail appeared unrelated to COX-2 expression. In cultured human keratinocytes, TPA induced Snail mRNA expression while suppressing Slug expression, and this differential regulation was due specifically to activation of the TPA receptor. These studies show that Slug and Snail exhibit similar patterns of expression during both UVR and chemical skin carcinogenesis, that Slug and Snail can be differentially regulated under some conditions and that in vitro findings may not recapitulate in vivo results.

  17. Enhanced photocatalytic degradation of norfloxacin in aqueous Bi{sub 2}WO{sub 6} dispersions containing nonionic surfactant under visible light irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Tang, Lin, E-mail: tanglin@hnu.edu.cn [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environmental Biology and Pollution Control (Hunan University), Ministry of Education, Changsha 410082 (China); Wang, Jiajia [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environmental Biology and Pollution Control (Hunan University), Ministry of Education, Changsha 410082 (China); Zeng, Guangming, E-mail: zgming@hnu.edu.cn [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environmental Biology and Pollution Control (Hunan University), Ministry of Education, Changsha 410082 (China); Liu, Yani; Deng, Yaocheng; Zhou, Yaoyu; Tang, Jing; Wang, Jingjing; Guo, Zhi [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environmental Biology and Pollution Control (Hunan University), Ministry of Education, Changsha 410082 (China)

    2016-04-05

    Highlights: • TX100 strongly enhanced the adsorption and photodegradation of NOF in Bi{sub 2}WO{sub 6} dispersions under visible light irradiation (400–750 nm). • Cu{sup 2+} (10 mM) significantly suppressed the photocatalytic degradation of NOF. • FT-IR demonstrated that the NOF adsorbed on Bi{sub 2}WO{sub 6} was completely degraded. • Three possible photocatalytic degradation pathways of NOF were proposed, according to the HPLC/MS/MS analysis. - Abstract: Photocatalytic degradation is an alternative method to remove pharmaceutical compounds in water, however it is hard to achieve efficient rate because of the poor solubility of pharmaceutical compounds in water. This study investigated the photodegradation of norfloxacin in a nonionic surfactant Triton-X100 (TX100)/Bi{sub 2}WO{sub 6} dispersion under visible light irradiation (400–750 nm). It was found that the degradation of poorly soluble NOF can be strongly enhanced with the addition of TX100. TX100 was adsorbed strongly on Bi{sub 2}WO{sub 6} surface and accelerated NOF photodegradation at the critical micelle concentration (CMC = 0.25 mM). Higher TX100 concentration (>0.25 mM) lowered the degradation rate. In the presence of TX100, the degradation rate reached the maximum value when the pH value was 8.06. FTIR analyses demonstrated that the adsorbed NOF on the catalyst was completely degraded after 2 h irradiation. According to the intermediates identified by HPLC/MS/MS, three possible degradation pathways were proposed to include addition of hydroxyl radical to quinolone ring, elimination of piperazynilic ring in fluoroquinolone molecules, and replacement of F atoms on the aromatic ring by hydroxyl radicals.

  18. Gemini surfactants from natural amino acids.

    Science.gov (United States)

    Pérez, Lourdes; Pinazo, Aurora; Pons, Ramon; Infante, Mrosa

    2014-03-01

    In this review, we report the most important contributions in the structure, synthesis, physicochemical (surface adsorption, aggregation and phase behaviour) and biological properties (toxicity, antimicrobial activity and biodegradation) of Gemini natural amino acid-based surfactants, and some potential applications, with an emphasis on the use of these surfactants as non-viral delivery system agents. Gemini surfactants derived from basic (Arg, Lys), neutral (Ser, Ala, Sar), acid (Asp) and sulphur containing amino acids (Cys) as polar head groups, and Geminis with amino acids/peptides in the spacer chain are reviewed.

  19. Characterizating Multi-layered Coastal Aquifer using Pneumatic Slug Tests

    Science.gov (United States)

    Malama, B.; Abere, M.; Mikenna, M.

    2016-12-01

    Results of pneumatic slug tests conducted in a monitoring wells of a shallow aquifer on the California Central Coast are presented. The aquifer is in the Los Osos groundwater basin on the California Central Coast, a semi-closed near-triangular groundwater basin bounded to the north and south by impermeable igneousbed rock and to the west by the Pacific Ocean. The groundwater basin is a multi-layered system comprising a perched, near-surface semi-confined, and a deep confined aquifer. The unincorporated community of Los Osos is wholly dependent on the groundwater basin that is threatened with seawater intrusion and nitratecontamination. The slug tests reported here were performed in the perched and semi-confined aquifers as part of a seawater intrusion characterization study. The semi-confined and confined aquifers show evidence of seawater intrusion with upconing in some deep aquifer municipal wells. The upconing has beeninterpreted by previous studies as evidence of preferential flow through a high permeability channel. The objective of the work was to test this hypothesis by mapping the horizontal and vertical spatial variability of hydraulic parameters across the basin and establish the extent of the high permeability unit.Here only preliminary results of slug tests conducted across the basin for vertically averaged hydraulic parameters are reported. The results provide an indication of the horizontal variability of hydraulic parameters. An additional study will be performed to characterize the vertical variability to investigate the probableexistsence of a high permeability channel.

  20. Online Slug Detection in Multi-phase Transportation Pipelines Using Electrical Tomography

    DEFF Research Database (Denmark)

    Pedersen, Simon; Mai, Christian; Hansen, Leif

    2015-01-01

    Slugging flow in offshore oil & gas multi-phase transportation pipelines cause big challenges as the flow regime induces flow and pressure oscillations in the multi-phase pipelines. The negative impacts of the most severe slugs are significant and thus the elimination of slugging flow....... Based on the results the study concludes that the ERT is able to detect the slug very well when the oil and water is well mixed. Furthermore the traditional pressure transmitters have the limitation that pressure variations can be caused by other operating conditions than slug, such as change...... in the back pressure from control valves. The biggest limitation using ERT is the lack of ability to distinguish between gas and oil, and thus the ERT can only be used as an effective slug detect measurement when the oil-to-water ratio is low....

  1. Slug control in Australian canola: monitoring, molluscicidal baits and economic thresholds.

    Science.gov (United States)

    Nash, Michael A; Thomson, Linda J; Hoffmann, Ary A

    2007-09-01

    Exotic slugs have become serious pests of canola, at establishment, in Southern Australian high-rainfall cropping zones. Slugs were monitored using relatively inexpensive 300 mm x 300 mm terracotta tiles acting as refuges. An investigation was made of the effects of the time of application of chelated iron baits on the slug species Deroceras reticulatum Müller and Lehmannia nyctelia Bourguignat. Baits reduced the number of surface-active slug species. A single application at sowing provided greater efficacy than one application before sowing, and efficacy was comparable with that of two applications. Canola seedling densities showed a negative response to D. reticulatum numbers; the presence of even one individual per refuge trap reduced seedling numbers below optimum densities. Thistles and other vegetation were associated with increased numbers of slugs. European guidelines for slug monitoring and damage appear to be at least partly applicable to Australian conditions.

  2. Studies on the Treatment of Wastewater Containing Anion Surfactants with OFR Technique%废水中阴离子表面活性剂的最优化处理工艺

    Institute of Scientific and Technical Information of China (English)

    刘怡; 熊亚; 朱锡海

    2001-01-01

    In this paper,a new method for the treatment of wastewater containing anion surfactants by electrogenerated hydroxyl radical(·OH) in the OFR has been established. Anion surfactants for dodecylbenzene sulphonic acid sodium (DBS) and dodecyl sulphonic acid sodium(DDS) are selected as model pollutants to study their removal rate and the degradation mechanism in the OFR. The main physico-chemical factors affecting the removal rate were investigated,such as type of catalyst, filler size, cell voltage, interelectrode distance, air flow, treating time, the concentration, pH and conductivity of testing solution etc. The optimal conditions have been found out with the removal rate of DBS and DDS above 95% .Residual concentrations of the effluent correspond to GB 8978- 1996 for national new standard.%应用氧化絮凝复合床降解废水中的阴离子表面活性剂,系统地研究了各种主要的物理化学因素;催化剂种类、填料颗粒粒度、槽电压、电极间距离、压缩空气流量、试样的浓度、酸度、电导率和处理时间等对阴离子表面活性剂去除效果的影响,找到了相关的影响规律,确定了最佳的物理化学条件。实验结果表明,阴离子表面活性剂的去除率在95%以上,出水的水质可以达到国家的排放标准。

  3. Surfactant-assisted liquefaction of particulate carbonaceous substances

    Science.gov (United States)

    Hsu, G. C. (Inventor)

    1978-01-01

    A slurry of carbonaceous particles such as coal containing an oil soluble polar substituted oleophilic surfactant, suitably an amine substituted long chain hydrocarbon, is liquefied at high temperature and high hydrogen presence. The pressure of surfactant results in an increase in yield and the conversion product contains a higher proportion of light and heavy oils and less asphaltene than products from other liquefaction processes.

  4. Hydraulic Tomography and High-Resolution Slug Testing to Determine Hydraulic Conductivity Distributions - Year 1

    Science.gov (United States)

    2005-12-01

    the addition into a well of a known volume of water or a physical slug. More recently, pneumatic methods have become popular ( Zemansky and McElwee...and Zemansky , 2000), (Sellwood, 2001) and (Ross, 2004)]. The aquifer material at GEMS exhibits linear and non-linear responses to slug testing...1976; Zurbuchen et al., 2002; and Zemansky and McElwee, 2005). Slug tests have been a common method for obtaining information about the hydraulic

  5. Kinetics of gravity-driven slug flow in partially wettable capillaries of varying cross section

    Science.gov (United States)

    Nissan, Alon; Wang, Qiuling; Wallach, Rony

    2016-11-01

    A mathematical model for slug (finite liquid volume) motion in not-fully-wettable capillary tubes with sinusoidally varying cross-sectional areas was developed. The model, based on the Navier-Stokes equation, accounts for the full viscous terms due to nonuniform geometry, the inertial term, the slug's front and rear meniscus hysteresis effect, and dependence of contact angle on flow velocity (dynamic contact angle). The model includes a velocity-dependent film that is left behind the advancing slug, reducing its mass. The model was successfully verified experimentally by recording slug movement in uniform and sinusoidal capillary tubes with a gray-scale high-speed camera. Simulation showed that tube nonuniformity has a substantial effect on slug flow pattern: in a uniform tube it is monotonic and depends mainly on the slug's momentary mass/length; an undulating tube radius results in nonmonotonic flow characteristics. The static nonzero contact angle varies locally in nonuniform tubes owing to the additional effect of wall slope. Moreover, the nonuniform cross-sectional area induces slug acceleration, deceleration, blockage, and metastable-equilibrium locations. Increasing contact angle further amplifies the geometry effect on slug propagation. The developed model provides a modified means of emulating slug flow in differently wettable porous media for intermittent inlet water supply (e.g., raindrops on the soil surface).

  6. Stability of stratified flow and slugging in horizontal gas-liquid flow

    Institute of Scientific and Technical Information of China (English)

    GU Hanyang; GUO Liejin

    2005-01-01

    A transient one-dimensional two-fluid model is proposed to investigate numerically the interfacial instability and the onset of slugging for liquid-gas flow in a horizontal duct. In the present model, the effects of surface tension and transverse variations in dynamic pressure are taken into account. The evolution of interfacial disturbances is displayed and compared with the linear viscous KelvinHelmholtz stability analyses. It shows that interfacial wave is more instable due to the non-linear effect. The model predicts well the stability limit of stratified flow in comparison with the experimental data, and also automatically tracks the onset of slugging. The results show that the initiation of hydrodynamic slugging is related to local interfacial instability. Based on the cycle of slugging, a model for slug frequency is presented, which predicts the trends of slug frequencies with gas/liquid flow rate well in comparison with the available data. The effects of physical properties on slugging have been examined. It is found that with the increase in the gas viscosity and liquid density the slugging would be inhibited, whereas, with the increase in liquid viscosity and gas density, the slugging can be promoted.

  7. A new index for precise design and advanced operation of mass transfer in slug flow

    OpenAIRE

    Aoki, Nobuaki; Tanigawa, Shin; Mae, Kazuhiro

    2011-01-01

    Slug flow, one of the ordered multi-phase flow patterns in a small channel, has the advantage of the enhancement of mixing in each phase and mass transfer between two phases due to the internal circulation flow. To form stable slug flow, the throughput of order of μL min−1 has been employed. To use slug flow in industrial scale, however, controlled and high throughput mass transfer and an index for design of a channel with slug flow are required. To address this requirement, we examined the i...

  8. Three-dimensional numerical simulations of three-phase slug flows in horizontal pipes

    Science.gov (United States)

    Wang, Yan; Yang, Junfeng; Matar, Omar

    2015-11-01

    One of the most common flow regimes in pipelines is that of slug flow: slug bodies corresponding to alternating blocks of aerated liquid which bridge the pipe, separated by elongated bubbles; the latter ride atop a liquid layer. The slugs travel at velocities that exceed the mixture superficial velocity; this can potentially cause structural damage, particularly at pipe bends and junctions. Two-phase slug flows have received considerable attention in the literature both experimentally and computationally but there has been very little work carried out on three-phase slugging. In the present work, the evolution of oil-water-air three-phase slug flow in a horizontal cylindrical pipe is investigated using two-dimensional and three-dimensional computational fluid dynamics simulations. The parameters characterising three-phase slug flow, e.g. slug length, propagation velocity, and slug formation frequency, are determined for various gas and liquid superficial velocities for a given pipe geometry. The results of this work are compared to available experimental data and numerical solutions based on approximate, one-dimensional models relying on the use of empirical correlations. EPSRC Programme Grant, MEMPHIS, EP/K0039761/1.

  9. Surfactants tailored by the class Actinobacteria

    Directory of Open Access Journals (Sweden)

    Johannes H Kügler

    2015-03-01

    Full Text Available Gloablly, the drive towards the establishment of a bio-based economy has resulted in an increased need for bio-based applications. This, in turn, has served as a driving force for the discovery and application of novel biosurfactants. The class Actinobacteria represents a vast group of microorganisms with the ability to produce a diverse range of secondary metabolites, including surfactants. Understanding the extensive nature of the biosurfactants produced by actinobacterial strains can assist in finding novel biosurfactants with new potential applications. This review therefore presents a comprehensive overview of the knowledge available on actinobacterial surfactants, the chemical structures that have been completely or partly elucidated, as well as the identity of the biosurfactant-producing strains. Producer strains of not yet elucidated compounds are discussed, as well as the original habitats of all the producer strains, which seems to indicate that biosurfactant production is environmentally driven. Methodology applied in the isolation, purification and structural elucidation of the different types of surface active compounds, as well as surfactant activity tests, are also discussed. Overall, actinobacterial surfactants can be summarized to include the dominantly occurring trehalose-comprising surfactants, other non-trehalose containing glycolipids, lipopeptides and the more rare actinobacterial surfactants. The lack of structural information on a large proportion of actinobacterial surfactants should be considered as a driving force to further explore the abundance and diversity of these compounds. This would allow for a better understanding of actinobacterial surface active compounds and their potential for biotechnological application.

  10. UV-visible spectroscopy as an alternative to liquid chromatography for determination of everolimus in surfactant-containing dissolution media: a useful approach based on solid-phase extraction.

    Science.gov (United States)

    Kamberi, Marika; Tran, Thu-Ngoc

    2012-11-01

    High-throughput 96-well solid phase extraction (SPE) plate with C-18 reversed phase sorbent followed by UV-visible (UV-Vis) microplate reader was applied to the analysis of hydrophobic drugs in surfactant-containing dissolution media, which are often used to evaluate the in-vitro drug release of drug eluting stents (DES). Everolimus and dissolution medium containing Triton X-405 were selected as representatives, and the appropriate SPE conditions (adsorption, washing and elution) were investigated to obtain a practical and reliable sample clean-up. It was shown that the developed SPE procedure was capable of removing interfering components (Triton X-405 and its impurities), allowing for an accurate automated spectrophotometric analysis to be performed. The proposed UV-Vis spectrophotometric method yielded equivalent results compared to a classical LC analysis method. Linear regression analysis indicated that both methods have the ability to obtain test results that are directly proportional to the concentration of analyte in the sample within the selected range of 1.0-10 μg/ml for everolimus, with a coefficient of correlation (r(2)) value of >0.998 and standard deviation of the residuals (Syx) of UV-Vis spectrophotometric method and from 98 to 102 for the HPLC method, respectively. The 95% CI of the mean recovery for the UV-Vis spectrophotometric method was 99-102% and for the HPLC method was 99-101%. No statistical difference was found between the mean recoveries of the methods (p=0.42). Hence the methods are free from interference due to Triton and other chemicals present in the dissolution medium. The variation in the amount of everolimus estimated by UV-Vis spectrophotometric and HPLC methods was ≤3.5%, and the drug release profiles obtained by both methods were found to be equivalent by evaluation with two-one-sided t-test (two-tailed, p=0.62; mean of differences, 0.17; 95% CI, 0.62-0.96) and similarity factor f2 (f2 value, 87). The excellent conformity of

  11. Synthesis and properties evaluation of sulfobetaine surfactant with double hydroxyl

    Science.gov (United States)

    Zhou, Ming; Luo, Gang; Zhang, Ze; Li, Sisi; Wang, Chengwen

    2017-09-01

    A series of sulfobetaine surfactants {N-[(3-alkoxy-2-hydroxyl)propoxy] ethyl-N,N-dimethyl-N-(2-hydroxyl)propyl sulfonate} ammonium chloride were synthesized with raw materials containing linear saturated alcohol, N,N-dimethylethanolamine, sodium 3-chloro-2-hydroxyl propane sulfonic acid and epichlorohydrin. The molecule structures of sulfobetaine surfactants were characterized by FTIR, 1HNMR and elemental analysis. Surface tension measurements can provide us information about the surface tension at the CMC (γCMC), pC20, Γmax and Amin. The pC20 values of sulfobetaine surfactants increase with the hydrophobic chain length increasing. Amin values of the surfactants decrease with increasing hydrophobic chain length from 10 to 14. The critical micelle concentration (CMC) and surface tension (γCMC) values of the sulfobetaine surfactants decrease with increasing hydrophobic chain length from 10 to 16. The lipophilicity of surfactant was enhanced with the increase of the carbon chain, however, the ability of anti-hard water was weakened. The minimum oil/water interfacial tension of four kinds of sulfobetaine surfactants is 10-2-10-3 mN/m magnitude, which indicates that the synthesized bis-hydroxy sulfobetaine surfactants have a great ability to reduce interfacial tension in the surfactant flooding system. The surface tension (γCMC) values of synthesized surfactants were lower compared with conventional anionic surfactant sodium dodecyl sulfonate.

  12. Microemulsion-based lycopene extraction: Effect of surfactants, co-surfactants and pretreatments.

    Science.gov (United States)

    Amiri-Rigi, Atefeh; Abbasi, Soleiman

    2016-04-15

    Lycopene is a potent antioxidant that has received extensive attention recently. Due to the challenges encountered with current methods of lycopene extraction using hazardous solvents, industry calls for a greener, safer and more efficient process. The main purpose of present study was application of microemulsion technique to extract lycopene from tomato pomace. In this respect, the effect of eight different surfactants, four different co-surfactants, and ultrasound and enzyme pretreatments on lycopene extraction efficiency was examined. Experimental results revealed that application of combined ultrasound and enzyme pretreatments, saponin as a natural surfactant, and glycerol as a co-surfactant, in the bicontinuous region of microemulsion was the optimal experimental conditions resulting in a microemulsion containing 409.68±0.68 μg/glycopene. The high lycopene concentration achieved, indicates that microemulsion technique, using a low-cost natural surfactant could be promising for a simple and safe separation of lycopene from tomato pomace and possibly from tomato industrial wastes.

  13. The E-cadherin repressor slug and progression of human extrahepatic hilar cholangiocarcinoma

    Directory of Open Access Journals (Sweden)

    Wang Xin-sheng

    2010-07-01

    Full Text Available Abstract Objectives This study explored the expression and function of Slug in human extrahepatic hilar cholangiocarcinoma (EHC to identify its role in tumor progression. Methods The expression of Snail and Slug mRNA in 52 human tissue samples of EHC was investigated. The mRNA of Snail and Slug were quantified using reverse transcriptase-PCR, and correlations with E-cadherin expression and clinicopathological factors were investigated. We then investigated transfection of Slug cDNA in endogenous E-cadherin-positive human EHC FRH0201 cells, selectively induced the loss of E-cadherin protein expression, and then small interfering RNA (siRNA for inhibition of Slug expression in endogenous Slug-positive human EHC QBC939 cells, selectively induced the loss of Slug protein expression. A Boyden chamber transwell assay was used for invasion. Results Slug mRNA was overexpressed in 18 cases (34.6% of EHC compared with adjacent noncancerous tissue. E-Cadherin protein expression determined in the same 52 cases by immunohistochemistry was significantly down-regulated in those cases with Slug mRNA overexpression (P = 0.0001. The tumor and nontumor ratio of Slug mRNA was correlated with nodal metastasis(p = 0.0102, distant metastasis (p = 0.0001and Survival time(p = 0.0443. However, Snail mRNA correlated with neither E-cadherin expression nor tumor invasiveness. By inhibiting Slug expression by RNA interference, we found that reduced Slug levels upregulated E-cadherin and decreased invasion in QBC939 cell. When the QBC939 cells was infected with Slug cDNA,, significant E-cadherin was downregulated and increased invasion in QBC939 cell. Conclusions The results suggested that Slug expression plays an important role in both the regulation of E-cadherin expression and in the acquisition of invasive potential in human EHC. Slug is possibly a potential target for an antitumor therapy blocking the functions of invasion and metastasis in human EHCs.

  14. Surfactants in tribology

    CERN Document Server

    Biresaw, Girma

    2014-01-01

    Surface science and tribology play very critical roles in many industries. Manufacture and use of almost all consumer and industrial products rely on the application of advanced surface and tribological knowledge. The fourth in a series, Surfactants in Tribology, Volume 4 provides an update on research and development activities connecting surfactants and tribological phenomena. Written by renowned subject matter experts, the book demonstrates how improved design of surfactants can be harnessed to control tribological phenomena. Profusely illustrated and copiously referenced, the chapters also

  15. Seed consumption and dispersal of ant-dispersed plants by slugs.

    Science.gov (United States)

    Türke, Manfred; Heinze, Eric; Andreas, Kerstin; Svendsen, Sarah M; Gossner, Martin M; Weisser, Wolfgang W

    2010-07-01

    In beech-dominated forests in Central Europe, many spring geophytes show adaptations to seed dispersal by ants (myrmecochory). Ants, however, can be rare in such moist forests. Motivated by observations of slug feeding on seeds we investigated the seed consumption of two plant species, Anemone nemorosa and Asarum europaeum, by slugs, in a series of experiments. In a seed predation experiment in a beech forest, we found that seed removal was strongly reduced when gastropods were excluded from the seed depots. The contribution of insects, including ants, and rodents to seed removal was relatively less but differed between May and July. In the laboratory, slug species, in particular Arion sp., consumed seeds of both plant species. Slugs either consumed the elaiosomes of seeds or swallowed seeds intact. Swallowed seeds were defecated undamaged and germinated as well as control seeds when buried overwinter, indicating the potential for seed dispersal by slugs. We also recovered seeds of myrmecochores in the faeces of several slugs caught in forests. In a slug release experiment in the forest, slugs moved up to 14.6 m (mean 4.4 m) in 15 h, which is the median gut passage time of seeds based on measurements made in the laboratory. We also found that when slug-defecated seeds were offered to rodents, these were less attractive than control seeds, suggesting that passage through the slug gut reduces seed predation risk. Our results demonstrate that slugs are significant consumers of elaiosomes or entire seeds of ant-dispersed plants and that they can function as seed dispersers of these plants.

  16. [Liposome phospholipid substitution and lung function in surfactant deprived rats].

    Science.gov (United States)

    Obladen, M

    1985-01-01

    In vivo activity of an artificial surfactant was studied in surfactant depleted rats. After tenfold alveolar lavage, PaO2, tidal volume, and compliance of the respiratory system fell to one third of initial value. Substitution of large unilamellar vesicles containing 90% Dipalmitoylphosphatidylcholine and 10% unsaturated phosphatidylglycerol largely restored oxygenation and lung mechanics in most animals. Complete normalization with weaning from the ventilator, however, was achieved neither with liposomes nor with natural surfactant concentrate.

  17. POLYMERIC SURFACTANT STRUCTURE

    Institute of Scientific and Technical Information of China (English)

    P.M. Saville; J.W. White

    2001-01-01

    Polymeric surfactants are amongst the most widespread of all polymers. In nature, proteins and polysaccharides cause self organization as a result of this surfactancy; in industry, polymeric surfactants play key roles in the food, explosives and surface coatings sectors. The generation of useful nano- and micro-structures in films and emulsions as a result of polymer amphiphilicity and the application of mechanical stress is discussed. The use of X-ray and neutron small angle scattering and reflectivity to measure these structures and their dynamic properties will be described. New results on linear and dendritic polymer surfactants are presented.

  18. Dendrimer-surfactant interactions.

    Science.gov (United States)

    Cheng, Yiyun; Zhao, Libo; Li, Tianfu

    2014-04-28

    In this article, we reviewed the interactions between dendrimers and surfactants with particular focus on the interaction mechanisms and physicochemical properties of the yielding dendrimer-surfactant aggregates. In order to provide insight into the behavior of dendrimers in biological systems, the interactions of dendrimers with bio-surfactants such as phospholipids in bulk solutions, in solid-supported bilayers and at the interface of phases or solid-states were discussed. Applications of the dendrimer-surfactant aggregates as templates to guide the synthesis of nanoparticles and in drug or gene delivery were also mentioned.

  19. Surfactant adsorption study in sandstone for enhanced oil recovery; Estudo da adsorcao de tensoativos em arenitos para recuperacao avancada de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Curbelo, Fabiola D.S.; Santanna, Vanessa C.; Barros Neto, Eduardo L. de; Dutra Junior, Tarcilio V.; Dantas Neto, Afonso A. [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil). Dept. de Engenharia Quimica; Garnica, Alfredo I.C. [Universidade Federal da Paraiba (UFPB), Joao Pessoa, PB (Brazil). Dept. de Tecnologia Quimica e de Alimentos; Lucena Neto, Marciano [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil); Dantas, Tereza N.C. [Faculdade Natalense para o Desenvolvimento do RN (FARN), Natal, RN (Brazil)

    2004-07-01

    Adsorption of surfactants from aqueous solutions in porous media is very important in Enhanced Oil Recovery (EOR) of oil reservoirs because surfactant loss due to adsorption on the reservoir rocks weakens the effectiveness of the injected chemical slug in reducing oil-water tension (IFT) and makes the process uneconomical. In this paper, two nonionic surfactants, such as alkyl phenol polyoxyethylene, with different ethoxylation degrees were studied, ENP95 and ENP150. The results of flow experiments of surfactant solutions in porous media showed that adsorption was higher for ENP95 because it has smaller ethoxylation degree than ENP150. This occurs what with increasing length of the head group, the molecules become more hydrophilic and, in associated structures, the steric hindrance between the head groups increases. Generally speaking, adsorption appears to be a cooperative process involving lateral interaction between surfactant and weak interaction with the solid surface. (author)

  20. Surfactant Sector Needs Urgent Readjustment

    Institute of Scientific and Technical Information of China (English)

    Huang Hongzhou

    2007-01-01

    @@ Surfactant industrial system has been basically established After 50 years' development, China has already established a surfactant industrial system with a relatively complete product portfolio and can produce 4714 varieties of surfactants in cationic,anionic, nonionic and amphoteric categories.

  1. Tandonia kusceri (Pulmonata: Milacidae, a slug new for Slovakia

    Directory of Open Access Journals (Sweden)

    Ondřej Korábek

    2016-07-01

    Full Text Available Tandonia kusceri (Wagner, 1931 is reported from Slovakia for the first time. The slug was found in the Ružinov and Petržalka housing estates, Bratislava, in 2014 and 2015, respectively. Our observations suggest that the species is well established in the Slovak capital. This finding calls for verification of some of the older reports of a similar species Tandonia rustica beyond the eastern border of its native range. Owing to unresolved taxonomic issues, the name T. kusceri should be applied only tentatively.

  2. Study of the combined effects of a peracetic acid-based disinfectant and surfactants contained in hospital effluents on Daphnia magna.

    Science.gov (United States)

    Panouillères, Muriel; Boillot, Clotilde; Perrodin, Yves

    2007-04-01

    Hospital effluents cause environmental problems since they are 5-15 more toxic than urban effluents and they are not subjected to any pre-treatment before being discharged into urban sewage networks. The hypothesis used to explain this toxicity is the presence of disinfectants and detergents. This study is aimed at highlighting the ecotoxicity of a peracetic acid-based disinfectant to Daphnia magna, as well as the combined effects of this disinfectant in binary mixtures with three types of detergent. The detergents used here are: cetyltrimethylammonium bromide (CTAB, cationic), sodium dodecylsulfate (SDS, anionic) and Triton X-100 (TX, non-ionic). The toxicity of the mixtures is studied as a function of five predefined ratios. At the end of the study, we conclude that peracetic acid seems to be slightly toxic to Daphnia magna. Indeed, the efficient concentration inhibiting the mobility of 50% of the population of Daphnia at 24 h (EC50) is 116.6 mg/l. Globally, additive effects are observed for all the binary peracetic acid-detergent mixtures. However, for the peracetic acid-TX mixture, its effects have antagonistic tendencies whereas the peracetic acid-CTAB mixture has slight synergic tendencies. The mixture containing peracetic acid and SDS is slightly antagonistic for ratios containing more than 50% peracetic acid.

  3. EFFECTS OF BAITS AND BAIT ALTERNATIVES ON SLUG MORTALITY, EGG PRODUCTION, AND SEEDLING SURVIVAL

    Science.gov (United States)

    Two non-bait slug control formulations that are not attractive to earthworms including Durham 3.5 and 7.5 (3.5 and 7.5%, metaldehyde, respectively) and SlugFest AWF (all-weather-formula, 25%, metaldehyde), a liquid spray product were investigated for their efficacy in reducing egg fecundity and slu...

  4. Long liquid slugs in stratified gas/liquid flow in horizontal and slightly inclined pipes

    NARCIS (Netherlands)

    Kadri, U.

    2009-01-01

    Long liquid slugs reaching several hundreds pipe diameter may appear when transporting gas and liquid in horizontal and near horizontal pipes. The long slugs cause system vibration and separation difficulties that may lead to operational failures. Identifying and predicting the time and length scale

  5. Long liquid slugs in stratified gas/liquid flow in horizontal and slightly inclined pipes

    NARCIS (Netherlands)

    Kadri, U.

    2009-01-01

    Long liquid slugs reaching several hundreds pipe diameter may appear when transporting gas and liquid in horizontal and near horizontal pipes. The long slugs cause system vibration and separation difficulties that may lead to operational failures. Identifying and predicting the time and length scale

  6. Transformation of a Water Slug in Free Fall Under the Conditions of Exposure to an Air Flow Orthogonal to the Direction of the Slug Motion

    Science.gov (United States)

    Volkov, R. S.; Zabelin, M. V.; Kuznetsov, G. V.; Strizhak, P. A.

    2016-07-01

    An experimental study has been made of the influence of an orthogonal (side) air flow propagating with a velocity to 5 m/s on the phases of transformation of a water slug with an initial volume of 0.05-0.5 liter in free fall from a height of 3 m. Use was made of Phantom V411 and Phantom Miro M310 high-speed video cameras and a Tema Automotive software system with the function of continuous tracking. The laws of retardation of the phases of transformation of the water slug from the instant of formation to that of formation of a droplet cloud under the action of the air flow orthogonal to the direction of the slug motion, and also of the deceleration, removal, and destruction of the droplets and fragments of water separating from the slug surface, have been established.

  7. Noise and Directionality in a SLUG Microwave Amplifier for Superconducting Qubit Readout

    Science.gov (United States)

    Thorbeck, Ted; Zhu, Shaojiang; Leonard, Edward; McDermott, Robert

    2015-03-01

    Josephson parametric amplifiers have been widely used for low-noise dispersive readout of superconducting qubits. However, multiple stages of cryogenic isolation are required to protect the qubit from the strong microwave pump tone and from the high temperature noise of downstream gain stages. We want to remove circulators and isolators from the measurement chain because they are bulky, expensive, and magnetic. The SLUG (superconducting low-inductance undulatory galvanometer) is a microwave amplifier that achieves broad bandwidth, low added noise, and high gain. In this talk we discuss measurements of the SLUG added noise (less than photon system added noise). We describe theoretical and experimental investigations of the SLUG reverse isolation. Finally, we discuss backaction of the SLUG on the measured qubit, and we present strategies for the suppression of SLUG backaction.

  8. Relationships Between Aphids (Insecta: Homoptera: Aphididae) and Slugs (Gastropoda: Stylommatophora: Agriolimacidae) Pests of Legumes (Fabaceae: Lupinus).

    Science.gov (United States)

    Kozłowski, Jan; Strażyński, Przemysław; Jaskulska, Monika; Kozłowska, Maria

    2016-01-01

    Lupin plants are frequently damaged by various herbivorous invertebrates. Significant among these are slugs and aphids, which sometimes attack the same plants. Relationships between aphids, slugs and food plant are very interesting. Grazing by these pests on young plants can lead to significant yield losses. There is evidence that the alkaloids present in some lupin plants may reduce grazing by slugs, aphids and other invertebrates. In laboratory study was analyzed the relationships between aphid Aphis craccivora and slug Deroceras reticulatum pests of legumes Lupinus angustifolius. It was found that the presence of aphids significantly reduced slug grazing on the plants. The lupin cultivars with high alkaloid content were found to be less heavily damaged by D. reticulatum, and the development of A. craccivora was found to be inhibited on such plants.

  9. SURFACTANTS IN LUBRICATION

    Science.gov (United States)

    Surfactants are one of the most widely applied materials by consumers and industry. The application areas for surfactants span from everyday mundane tasks such as cleaning, to highly complex processes involving the formulation of pharmaceuticals, foods, pesticides, lubricants, etc. Even though sur...

  10. Dynamic covalent surfactants

    NARCIS (Netherlands)

    Minkenberg, C.B.

    2012-01-01

    In this thesis the development of surfactant aggregates with fast exchange dynamics between the aggregated and non-aggregated state is described. Dynamic surfactant exchange plays an important role in natural systems, for instance in cell signaling, cell division, and uptake and release of cargo. Re

  11. Inactivation of pulmonary surfactant due to serum-inhibited adsorption and reversal by hydrophilic polymers: experimental

    DEFF Research Database (Denmark)

    Taeusch, H William; de la Serna, Jorge Bernardino; Perez-Gil, Jesus

    2005-01-01

    The rate of change of surface pressure, pi, in a Langmuir trough following the deposition of surfactant suspensions on subphases containing serum, with or without polymers, is used to model a likely cause of surfactant inactivation in vivo: inhibition of surfactant adsorption due to competitive...... adsorption of surface active serum proteins. Aqueous suspensions of native porcine surfactant, organic extracts of native surfactant, and the clinical surfactants Curosurf, Infasurf, and Survanta spread on buffered subphases increase the surface pressure, pi, to approximately 40 mN/m within 2 min....... The variation with concentration, temperature, and mode of spreading confirmed Brewster angle microscopy observations that subphase to surface adsorption of surfactant is the dominant form of surfactant transport to the interface. However (with the exception of native porcine surfactant), similar rapid...

  12. An Experimental Study of the Flowrate Transients in Slug Flow

    Institute of Scientific and Technical Information of China (English)

    HELimin; CHENZhenyu; 等

    2002-01-01

    An investigation of the characteristics of flowrate transients within slug flow was conducted in a largescale outdoor testing facility.The test section consisted of a 378m long,7.62cm diameter stainless steel pipe. Air and water were used as the test fluids.The response to a change of flowrate o either phase or two phases was measured using a series of pressure transducers and differential pressure transducers.An increase or decrease in gas flowrate caused a pressure overshoot above the value at new steady state or led to a pressure undershoot to form a temporary stratified flow.Pressure waves existed in the pipeline,spreading from the entrance to the exit.The magnitude of pressure overshoot in “up-gas”transient or of pressure undershoot and period of the temporary stratified flow in “Down-gas” transient are related to the change of gas flowrate and the distance away from the entrance.In contrast,the change in liquid flowrate was accommodated by smooth transitions between the corresponding steady states,and only one obvious change was found in the slug frequency.According to experimental results,the pressure overshoot,pressure undershoot and the pressure wave propagation were analyzed,and the phenomena were explained reasonably.Some correlations for the calculation of the pressure overshoot and undershoot were proposed.

  13. Experiments on the transition from stratified to slug flow in multiphase pipe flow

    Energy Technology Data Exchange (ETDEWEB)

    Kristiansen, Olav

    2004-12-01

    Severe slugging is reported from some field operations, where an increase in the production rate leads to a transition from steady stratified flow to slug flow in the pipeline. The slugs can be longer than anticipated for hydrodynamic slugging and the flow transients can then be a limitation for the production capacity. The objective was to perform a study on the flow pattern transition from stratified to slug flow. A particular point of interest was the possible occurrence of metastable flow and large initial slugs at elevated pressures. New data have been acquired in an experimental investigation of the transition from stratified to slug flow in horizontal and near-horizontal pipes at atmospheric and pressurised conditions. The experiments were performed with two-phase gas liquid and three-phase gas-liquid-liquid flows. Two flow facilities were used the NTNU Multiphase Flow Laboratory (short flow loop) and the SINTEF Multi-phase Flow Laboratory (long flow loop). Hold-up and pressure drop were measured, and flow patterns were determined visually and by evaluation of hold-up time traces. The following parameters were varied: 1) Inlet flow condition by variation of inlet pipe inclination. 2) System pressure (gas density). 3) Test section inclination (horizontal and near-horizontal). 4) Water cut. 5) Gas and liquid flow rates. 6) Pipe length. Slug flow or stratified flow was introduced upstream to promote either early or delayed transition to slug flow in the test section. A time series analysis was performed on the hold-up time traces, and average and distribution slug characteristics are reported, e.g. slug frequency, bubble propagation velocity, slug fraction, slug length, and growth rate. The results have been compared with steady state model predictions. The work consists of the following parts. 1) An initial study was performed at atmospheric air-water conditions in a short pipe. 2) Experiments at atmospheric and elevated pressures were performed in the medium

  14. Conformational and phase transitions in DNA--photosensitive surfactant solutions: Experiment and modeling.

    Science.gov (United States)

    Kasyanenko, N; Lysyakova, L; Ramazanov, R; Nesterenko, A; Yaroshevich, I; Titov, E; Alexeev, G; Lezov, A; Unksov, I

    2015-02-01

    DNA binding to trans- and cis-isomers of azobenzene containing cationic surfactant in 5 mM NaCl solution was investigated by the methods of dynamic light scattering (DLS), low-gradient viscometry (LGV), atomic force microscopy (AFM), circular dichroism (CD), gel electrophoresis (GE), flow birefringence (FB), UV-Vis spectrophotometry. Light-responsive conformational transitions of DNA in complex with photosensitive surfactant, changes in DNA optical anisotropy and persistent length, phase transition of DNA into nanoparticles induced by high surfactant concentration, as well as transformation of surfactant conformation under its binding to macromolecule were studied. Computer simulations of micelles formation for cis- and trans-isomers of azobenzene containing surfactant, as well as DNA-surfactant interaction, were carried out. Phase diagram for DNA-surfactant solutions was designed. The possibility to reverse the DNA packaging induced by surfactant binding with the dilution and light irradiation was shown.

  15. Surfactants in the environment.

    Science.gov (United States)

    Ivanković, Tomislav; Hrenović, Jasna

    2010-03-01

    Surfactants are a diverse group of chemicals that are best known for their wide use in detergents and other cleaning products. After use, residual surfactants are discharged into sewage systems or directly into surface waters, and most of them end up dispersed in different environmental compartments such as soil, water or sediment. The toxic effects of surfactants on various aquatic organisms are well known. In general, surfactants are present in the environment at levels below toxicity and in Croatia below the national limit. Most surfactants are readily biodegradable and their amount is greatly reduced with secondary treatment in wastewater treatment plants. The highest concern is the release of untreated wastewater or wastewater that has undergone primary treatment alone. The discharge of wastewater polluted with massive quantities of surfactants could have serious effects on the ecosystem. Future studies of surfactant toxicities and biodegradation are necessary to withdraw highly toxic and non-biodegradable compounds from commercial use and replace them with more environmentally friendly ones.

  16. Pulmonary surfactant and lung transplantation

    NARCIS (Netherlands)

    Erasmus, Michiel Elardus

    1997-01-01

    Pulmonary surfactant lowers the surface tension at the air-water interface inside the alveolus. This is achieved by adsorption of surfactant phospholipids at the air-water interface, a process controlled by surfactant-associated proteins, such as SP-A. In this way, surfactant prevents collapse of th

  17. Production of a high-velocity water slug using an impacting technique

    Science.gov (United States)

    Dehkhoda, S.; Bourne, N. K.

    2014-02-01

    A pulsed water jet consists of a series of discrete water slugs travelling at high velocity. Immediately after striking a target, these slugs apply high-intensity, short-duration transient stress pulses reaching an amplitude known as the water hammer pressure, followed by low-intensity, long-duration stationary stress at a lower stagnation pressure. The magnitude and duration of the water hammer and stagnation pressures are controlled by the size and quality of the water slugs. The use of water jets for rock cutting in mining operations is a centuries-old technology; however, practical methods for producing high-energy water slugs repeatedly have proven difficult. This can be partly due to the fact that the geometrical properties of a jet and so its effectiveness in creating damage is controlled and influenced by the method that is employed to generate the water slugs. This paper investigates the quality of a single water slug produced using an impacting technique where a hammer strikes a piston, resting on top of a water-filled chamber. The coherence and integrity of the jet core was of concern in this study. The impact impulse of the formed water jet was measured in a Kel-F target material using an embedded PVDF (Polyvinylidene fluoride) shock gauge. The recorded stress waveform was then used to determine the unity and endurance of the water slug stream once travelled through air.

  18. A Hydrodynamic Model for Slug Frequency in Horizontal Gas-Liquid Two-Phase Flow

    Institute of Scientific and Technical Information of China (English)

    刘磊; 孙贺东; 胡志华; 周芳德

    2003-01-01

    The prediction of slug frequency has important significance on gas-liquid two-phase flow. A hydrodynamic model was put forward to evaluate slug frequency for horizontal two-phase flow, based on the dependence of slug frequency on the frequency of unstable interfacial wave. Using air and water, experimental verification of the model was carried out in a large range of flow parameters. Six electrical probes were installed at different positions of a horizontal plexiglass pipe to detect slug frequency development. The pipe is 30 m long and its inner diameter is 24 ram. It is observed experimentally that the interracial wave frequency at the inlet is about i to 3 times the frequency of stable slug. The slug frequencies predicted by the model fit well with Tronconi (1990) model and the experimental data. The combination of the hydrodynamic model and the experimental data results in a conclusion that the frequency of equilibrium liquid slug is approximately half the minimum frequency of interfacial wave.

  19. Mathematical modelling of Liquid -Liquid extraction in the slug flow regime in a microchannel

    Science.gov (United States)

    Ramji, Sundari; Bhagavatula, Dinesh; Rakesh, Arjun; Pushpavanam, S.

    2016-11-01

    Mixing in the slug flow regime in microchannels is enhanced by the presence of internal circulations induced by shear due to wall. This helps improve mass transfer in this flow regime. We exploit the low Re characteristic of the flow and seek a numerical solution to understand the structure of the vortex patterns formed in the two phases in the slug flow regime. We study liquid-liquid extraction in the system to determine the improvement in mass transfer. The system was analyzed for two cases when there is (i) no film surrounding the slug (ii) a thin film surrounding the slug. The 2D governing equations for fluid flow are solved using two approaches: a) a stream function formulation based on finite differences b) primitive variable formulation with the Chebyshev collocation method. The effect of viscosity ratio, slug length and film thickness on the vortex structure were studied. While secondary vortices were induced in the less viscous phase in the case where the thin film is absent, they are always generated in the slug irrespective of the viscosity ratio in the case where the film is present. The species balance equation was then solved numerically using two approaches: a) an Alternating Direction Explicit method and b) the Locally One Dimensional splitting technique. The effect of varying Peclet number from 0 to 104 on the solute transfer from the slug to the continuous phase was studied. The extraction performance is analyzed in terms of extraction efficiency and mass transfer coefficient.

  20. Influence of the initial conditions for the numerical simulation of two-phase slug flow

    Energy Technology Data Exchange (ETDEWEB)

    Pachas Napa, Alex A.; Morales, Rigoberto E.M.; Medina, Cesar D. Perea

    2010-07-01

    Multiphase flows in pipelines commonly show several patterns depending on the flow rate, geometry and physical properties of the phases. In oil production, the slug flow pattern is the most common among the others. This flow pattern is characterized by an intermittent succession in space and time of an aerated liquid slug and an elongated gas bubble with a liquid film. Slug flow is studied through the slug tracking model described as one-dimensional and Lagrangian frame referenced. In the model, the mass and the momentum balance equations are applied in control volumes constituted by the gas bubble and the liquid slug. Initial conditions must be determined, which need to reproduce the intermittence of the flow pattern. These initial conditions are given by a sequence of flow properties for each unit cell. Properties of the unit cell in initial conditions should reflect the intermittence, for which they can be analyzed in statistical terms. Therefore, statistical distributions should be obtained for the slug flow variables. Distributions are complemented with the mass balance and the bubble design model. The objective of the present work is to obtain initial conditions for the slug tracking model that reproduce a better adjustment of the fluctuating properties for different pipe inclinations (horizontal, vertical or inclined). The numerical results are compared with experimental data obtained by PFG/FEM/UNICAMP for air-water flow at 0 deg, 45 deg and 90 deg and good agreement is observed. (author)

  1. Metathesis depolymerizable surfactants

    Science.gov (United States)

    Jamison, Gregory M.; Wheeler, David R.; Loy, Douglas A.; Simmons, Blake A.; Long, Timothy M.; McElhanon, James R.; Rahimian, Kamyar; Staiger, Chad L.

    2008-04-15

    A class of surfactant molecules whose structure includes regularly spaced unsaturation in the tail group and thus, can be readily decomposed by ring-closing metathesis, and particularly by the action of a transition metal catalyst, to form small molecule products. These small molecules are designed to have increased volatility and/or enhanced solubility as compared to the original surfactant molecule and are thus easily removed by solvent extraction or vacuum extraction at low temperature. By producing easily removable decomposition products, the surfactant molecules become particularly desirable as template structures for preparing meso- and microstructural materials with tailored properties.

  2. Droplet and slug formation in polymer electrolyte membrane fuel cell flow channels: The role of interfacial forces

    Science.gov (United States)

    Colosqui, Carlos E.; Cheah, May J.; Kevrekidis, Ioannis G.; Benziger, Jay B.

    A microfluidic device is employed to emulate water droplet emergence from a porous electrode and slug formation in the gas flow channel of a PEM fuel cell. Liquid water emerges from a 50 μm pore forming a droplet; the droplet grows to span the entire cross-section of a microchannel and transitions into a slug which detaches and is swept downstream. Droplet growth, slug formation, detachment, and motion are analyzed using high-speed video images and pressure-time traces. Slug volume is controlled primarily by channel geometry, interfacial forces, and gravity. As water slugs move downstream, they leave residual micro-droplets that act as nucleation sites for the next droplet-to-slug transition. Residual liquid in the form of micro-droplets results in a significant decrease in slug volume between the very first slug formed in an initially dry channel and the ultimate "steady-state" slug. A physics-based model is presented to predict slug volumes and pressure drops for slug detachment and motion.

  3. Spatiotemporal analysis of predation by carabid beetles (Carabidae on nematode infected and uninfected slugs in the field.

    Directory of Open Access Journals (Sweden)

    Bjørn Arild Hatteland

    Full Text Available The dynamics of predation on parasites within prey has received relatively little attention despite the profound effects this is likely to have on both prey and parasite numbers and hence on biological control programmes where parasites are employed. The nematode Phasmarhabditis hermaphrodita is a commercially available biological agent against slugs. Predation on these slugs may, at the same time, result in intraguild predation on slug-parasitic nematodes. This study describes, for the first time, predation by carabid beetles on slugs and their nematode parasites on both spatial and temporal scales, using PCR-based methods. The highest nematode infection levels were found in the slugs Deroceras reticulatum and Arion silvaticus. Numbers of infected slugs decreased over time and no infected slugs were found four months after nematode application. The density of the most abundant slug, the invasive Arion vulgaris, was positively related to the activity-density of the carabid beetle, Carabus nemoralis. Predation on slugs was density and size related, with highest predation levels also on A. vulgaris. Predation on A. vulgaris decreased significantly in summer when these slugs were larger than one gram. Predation by C. nemoralis on slugs was opportunistic, without any preferences for specific species. Intraguild predation on the nematodes was low, suggesting that carabid beetles such as C. nemoralis probably do not have a significant impact on the success of biological control using P. hermaphrodita.

  4. Thermodynamics of non-ionic surfactant Triton X-100-cationic surfactants mixtures at the cloud point

    Energy Technology Data Exchange (ETDEWEB)

    Batigoec, Cigdem [Department of Chemistry, Faculty of Sciences, Trakya University, 22030 Edirne (Turkey); Akbas, Halide, E-mail: hakbas34@yahoo.com [Department of Chemistry, Faculty of Sciences, Trakya University, 22030 Edirne (Turkey); Boz, Mesut [Department of Chemistry, Faculty of Sciences, Trakya University, 22030 Edirne (Turkey)

    2011-12-15

    Highlights: > Non-ionic surfactants are used as emulsifier and solubilizate in such as textile, detergent and cosmetic. > Non-ionic surfactants occur phase separation at temperature as named the cloud point in solution. > Dimeric surfactants have attracted increasing attention due to their superior surface activity. > The positive values of {Delta}G{sub cp}{sup 0} indicate that the process proceeds nonspontaneous. - Abstract: This study investigates the effects of gemini and conventional cationic surfactants on the cloud point (CP) of the non-ionic surfactant Triton X-100 (TX-100) in aqueous solutions. Instead of visual observation, a spectrophotometer was used for measurement of the cloud point temperatures. The thermodynamic parameters of these mixtures were calculated at different cationic surfactant concentrations. The gemini surfactants of the alkanediyl-{alpha}-{omega}-bis (alkyldimethylammonium) dibromide type, on the one hand, with different alkyl groups containing m carbon atoms and an ethanediyl spacer, referred to as 'm-2-m' (m = 10, 12, and 16) and, on the other hand, with -C{sub 16} alkyl groups and different spacers containing s carbon atoms, referred to as '16-s-16' (s = 6 and 10) were synthesized, purified and characterized. Additions of the cationic surfactants to the TX-100 solution increased the cloud point temperature of the TX-100 solution. It was accepted that the solubility of non-ionic surfactant containing polyoxyethylene (POE) hydrophilic chain was a maximum at the cloud point so that the thermodynamic parameters were calculated at this temperature. The results showed that the standard Gibbs free energy ({Delta}G{sub cp}{sup 0}), the enthalpy ({Delta}H{sub cp}{sup 0}) and the entropy ({Delta}S{sub cp}{sup 0}) of the clouding phenomenon were found positive in all cases. The standard free energy ({Delta}G{sub cp}{sup 0}) increased with increasing hydrophobic alkyl chain for both gemini and conventional cationic

  5. Structured fluids polymers, colloids, surfactants

    CERN Document Server

    Witten, Thomas A

    2010-01-01

    Over the last thirty years, the study of liquids containing polymers, surfactants, or colloidal particles has developed from a loose assembly of facts into a coherent discipline with substantial predictive power. These liquids expand our conception of what condensed matter can do. Such structured-fluid phenomena dominate the physical environment within living cells. This book teaches how to think of these fluids from a unified point of view showing the far-reaching effects ofthermal fluctuations in producing forces and motions. Keeping mathematics to a minimum, the book seeks the simplest expl

  6. Experimental Study of Stable Surfaces for Anti-Slug Control in Multi-phase Flow

    DEFF Research Database (Denmark)

    Pedersen, Simon; Løhndorf, Petar Durdevic; Yang, Zhenyu

    2014-01-01

    The severe slugging flow is always challenging in oil & gas production, especially for the current offshore based production. The slugging flow can cause a lot of potential problems, such as those relevant to production safety, fatigue as well as capability. As one typical phenomenon in multi......-phase flow dynamics, the slug can be avoided or eliminated by proper facility design and control of operational conditions. Based on a testing facility which can emulate a pipeline-riser or a gas-lifted production well in a scaled-down manner, this paper experimentally studies the correlations of key...

  7. Phosphine oxide surfactants revisited.

    Science.gov (United States)

    Stubenrauch, Cosima; Preisig, Natalie; Laughlin, Robert G

    2016-04-01

    This review summarizes everything we currently know about the nonionic surfactants alkyl dimethyl (C(n)DMPO) and alkyl diethyl (C(n)DEPO) phosphine oxide (PO surfactants). The review starts with the synthesis and the general properties (Section 2) of these compounds and continues with their interfacial properties (Section 3) such as surface tension, surface rheology, interfacial tension and adsorption at solid surfaces. We discuss studies on thin liquid films and foams stabilized by PO surfactants (Section 4) as well as studies on their self-assembly into lyotropic liquid crystals and microemulsions, respectively (Section 5). We aim at encouraging colleagues from both academia and industry to take on board PO surfactants whenever possible and feasible because of their broad variety of excellent properties.

  8. Study of surfactant-skin interactions by skin impedance measurements.

    Science.gov (United States)

    Lu, Guojin; Moore, David J

    2012-02-01

    The stratum corneum (SC) plays a very critical physiological role as skin barrier in regulating water loss through the skin and protects the body from a wide range of physical and chemical exogenous insults. Surfactant-containing formulations can induce skin damage and irritation owing to surfactant absorption and penetration. It is generally accepted that reduction in skin barrier properties occurs only after surfactants have penetrated/permeated into the skin barrier. To mitigate the harshness of surfactant-based cleansing products, penetration/permeation of surfactants should be reduced. Skin impedance measurements have been taken in vitro on porcine skin using vertical Franz diffusion cells to investigate the impact of surfactants, temperature and pH on skin barrier integrity. These skin impedance results demonstrate excellent correlation with other published methods for assessing skin damage and irritation from different surfactant chemistry, concentration, pH, time of exposure and temperature. This study demonstrates that skin impedance can be utilized as a routine approach to screen surfactant-containing formulations for their propensity to compromise the skin barrier and hence likely lead to skin irritation.

  9. Efficient deacylation of N-acylimidazoles by functionalized surfactant micelles

    OpenAIRE

    Ihara, Yasuji; Nango, Mamoru; Koga, Joichi; ナンゴ, マモル; 南後, 守

    1989-01-01

    Hydroxylated surfactant micelles are powerful catalysts for the deacylation of N-acylimidazoles under neutral conditions; the deacylation rates of hydrophobia acylimidazoles are accelerated remarkably by functionalized micelles containing three hydroxy groups at the polar head.

  10. SLUG: Critical regulator of epithelial cell identity in breast development and cancer.

    Science.gov (United States)

    Phillips, Sarah; Kuperwasser, Charlotte

    2014-01-01

    SLUG, a member of the SNAIL family of transcriptional repressors, is known to play a diverse number of roles in the cell, and its deregulation has been observed in a variety of cancers including breast. Here, we focus on SLUG's role as a master regulator of mammary epithelial cell (MEC) fate and lineage commitment in the normal mammary gland, and discuss how aberrant SLUG expression can influence breast tumor formation, phenotype, and progression. Specifically, we discuss SLUG's involvement in MEC differentiation, stemness, cellular plasticity, and the epithelial to mesenchymal transition (EMT), and highlight the complex connection between these programs during development and disease progression. Undoubtedly, delineating how molecular factors influence lineage identity and cell-state dynamics in the normal mammary gland will contribute to our understanding of breast tumor heterogeneity.

  11. Experimental Study of Stable Surfaces for Anti-Slug Control in Multi-phase Flow

    DEFF Research Database (Denmark)

    Pedersen, Simon; Løhndorf, Petar Durdevic; Stampe, Kasper;

    2016-01-01

    Severe slugging flow is always challenging in oil & gas production, especially for the current offshore based production. The slugging flow can cause a lot of problems, such as those relevant to production safety, fatigue as well as capability. As one typical phenomenon in multi-phase flow dynamics......, the slug can be avoided or eliminated by proper facility design or control of operational conditions. Based on a testing facility which can emulate a pipeline-riser or a gas-lifted production well in a scaled-down manner, this paper experimentally studies the correlations of key operational parameters...... that the capability, performance and efficiency of anti-slug control can be dramatically improved if these stable surfaces can be experimentally determined beforehand. The paper concludes that obtaining the stable surface on the new developed map can significantly improve the production rate in a control scheme. Even...

  12. SLUG Microwave Amplifier as a Nonreciprocal Gain Element for Scalable Qubit Readout

    Science.gov (United States)

    Thorbeck, Ted; Leonard, Edward; Zhu, Shaojiang; McDermott, Robert

    Josephson parametric amplifiers for superconducting qubits require several stages of cryogenic isolation to protect the qubit from strong microwave pump tones and downstream noise. But isolators and circulators are large, expensive and magnetic, so they are an obstacle to scaling up a superconducting quantum computer. In contrast, the SLUG (Superconducting Low-inductance Undulatory Galvanometer) is a high gain, broadband, low noise microwave amplifier that provides built-in reverse isolation. Here, we describe the dependence of the SLUG reverse isolation on signal frequency and device operating point. We show that the reverse isolation of the SLUG can be as large as or larger than that of a bulk commercial isolator. Finally, we discuss the use of the SLUG to read out a transmon qubit without isolators or circulators.

  13. Review of Slug Detection, Modeling and Control Techniques for Offshore Oil & Gas Production Processes

    DEFF Research Database (Denmark)

    Pedersen, Simon; Løhndorf, Petar Durdevic; Yang, Zhenyu

    2015-01-01

    The current offshore oil & gas multi-phase production and transportation installations have big challenges related with the slugging flow: An unstable multi-phase flow regime where the flow rates, pressures and temperatures oscillate in the considered processes. Slug can be caused by different...... of these methods can simultaneously reduce the oil & gas production, which is a very big concern as the production rate is the key evaluation parameter for offshore production. We conclude that the slugging flow is a well-defined phenomenon, even though this subject has been extensively investigated in the past...... operating conditions and installation structures. The most severe slugs are often induced in long vertical risers or production wells, where liquid blocks gas at the riser/well base and correspondingly it causes the pressure to accumulate and hence originates the oscillating performance. There are many...

  14. Cold tolerance and freeze-induced glucose accumulation in three terrestrial slugs

    DEFF Research Database (Denmark)

    Slotsbo, Stine; Hansen, Lars Monrad; Jordaens, Kurt;

    2012-01-01

    in their habitat. Slugs spontaneously froze at about -4 °C when cooled under dry conditions, but freezing of body fluids was readily induced at -1 °C when in contact with external ice crystals. All three species survived freezing for 2 days at -1 °C, and some A. rufus and A. lusitanicus also survived freezing......Cold tolerance and metabolic responses to freezing of three slug species common in Scandinavia (Arion ater, Arion rufus and Arion lusitanicus) are reported. Autumn collected slugs were cold acclimated in the laboratory and subjected to freezing conditions simulating likely winter temperatures....... Glucose increased from about 6 to 22 µg/mg dry tissue upon freezing in A. rufus, but less so in A. ater and A. lusitanicus. Glucose may thus act as a cryoprotectant in these slugs, although the concentrations are not as high as reported for other freeze tolerant invertebrates....

  15. BIOSYNTHESIS OF SURFACTANTS ON INDUSTRIAL WASTE

    Directory of Open Access Journals (Sweden)

    Pirog T. P.

    2014-10-01

    Full Text Available The literature and own experimental data on the synthesis of microbial surfactants of different chemical nature (rhamnolipids, sophorolipids, manozylerythritollipids, lipopeptides at various waste (vegetable oil and fat, sugar, dairy industry, agriculture, forestry, biodiesel, as well as waste — fried vegetable oils are presented. Most suitable substrates for the synthesis of microbial surfactants are oil containing waste that, unlike, for example, lignocellulose, whey, technical glycerol do not require pre-treatment and purification. Replacing traditional substrates for the biosynthesis of surfactant with industrial waste will help to reduce the cost of technology by several times, dispose of unwanted waste, solve the problem of storage or disposal of large amounts of waste from the food industry, agricultural sector and companies that produce biodiesel, which spent large amount of energy and money for such needs

  16. Surfactant apoprotein in nonmalignant pulmonary disorders.

    Science.gov (United States)

    Singh, G.; Katyal, S. L.

    1980-01-01

    Formalin-fixed, paraffin-embedded lungs exhibiting a variety of nonmalignant disorders were studied by immunoperoxidase staining using antibodies specific for surfactant apoprotein, IgG, IgM, IgA, albumin, fibrinogen, and lysozyme. Normal Type II pneumocytes showed staining for surfactant apoprotein in the perinuclear region only. The extent and intensity of staining for apoprotein was markedly increased in reactive Type II pneumocytes. This increase appeared to be a nonspecific reaction to lung injury. The intra-alveolar material in pulmonary alveolar proteinosis stained intensely for surfactant apoprotein, indicating that the accumulated proteinaceous material contained pulmonary surfactant. Type II pneumocytes in pulmonary alveolar proteinosis exhibited hyperplasia as well as hypertrophy. The few macrophages in lung affected by pulmonary alveolar proteinosis stained intensely for lysozyme. The excessive intraalveolar accumulation of proteinaceous material in pulmonary alveolar proteinosis may be the result of both an over-production as well as a deficient removal of pulmonary surfactant. Images Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 Figure 7 Figure 8 Figure 9 p[57]-a PMID:7004201

  17. 2-DE using hemi-fluorinated surfactants.

    Science.gov (United States)

    Starita-Geribaldi, Mireille; Thebault, Pascal; Taffin de Givenchy, Elisabeth; Guittard, Frederic; Geribaldi, Serge

    2007-07-01

    The synthesis of hemi-fluorinated zwitterionic surfactants was realized and assessed for 2-DE, a powerful separation method for proteomic analysis. These new fluorinated amidosulfobetaine (FASB-p,m) were compared to their hydrocarbon counterparts amidosulfobetaine (ASB-n) characterized by a hydrophilic polar head, a hydrophobic and lipophilic tail, and an amido group as connector. The tail of these FASB surfactants was in part fluorinated resulting in the modulation of its lipophilicity (or oleophobicity). Their effect on the red blood cell (RBC) membrane showed a specific solubilization depending on the length of the hydrophobic part. A large number of polypeptide spots appeared in the 2-DE patterns by using FASB-p,m. The oleophobic character of these surfactants was confirmed by the fact that Band 3, a highly hydrophobic transmembrane protein, was not solubilized by these fluorinated structures. The corresponding pellet was very rich in Band 3 and could then be solubilized by using a strong detergent such as amidosulfobetaine with an alkyl tail containing 14 carbon atoms (ASB-14). Thus, these hemi-fluorinated surfactants appeared as powerful tools when used at the first step of a two-step solubilization strategy using a hydrocarbon homologous surfactant in the second step.

  18. Modeling transport effects of perfluorinated and hydrocarbon surfactants in groundwater by using micellar liquid chromatography

    Energy Technology Data Exchange (ETDEWEB)

    Simmons, Rashad N. [Department of Chemistry and Center for Integrative Toxicology, Michigan State University, East Lansing, MI 48824-1322 (United States); McGuffin, Victoria L. [Department of Chemistry and Center for Integrative Toxicology, Michigan State University, East Lansing, MI 48824-1322 (United States)], E-mail: jgshabus@aol.com

    2007-11-05

    The effects of hydrocarbon and perfluorinated surfactants, above their critical micelle concentration (CMC), on the transport of neutral environmental pollutants are compared. Reversed-phase micellar liquid chromatography is used to model the groundwater system. The octadecylsilica stationary phase serves to simulate soil particles containing organic matter, whereas the aqueous surfactant mobile phases serve to simulate groundwater containing a surfactant at varying concentrations. Sodium dodecyl sulfate and lithium perfluorooctane sulfonate are used as representatives of the hydrocarbon and perfluorinated surfactants, respectively. Benzene, mono- and perhalogenated benzenes, and polycyclic aromatic hydrocarbons are used as models for environmental pollutants. Transport effects were elucidated from the retention factor, k, and the equilibrium constant per micelle, K{sub eq}, of the model pollutants in the individual surfactants. Based on k values, the transport of the model pollutants increased in both surfactant solutions in comparison to pure water. As the concentration of the surfactants increased, the transport of the pollutants increased as well. Notably, the K{sub eq} values of the pollutants in the perfluorinated surfactant were at least an order of magnitude less than those in the hydrocarbon surfactant. Overall, these results suggest that the presence of a perfluorinated surfactant, above its CMC, increases the transport of pollutants in a groundwater system. However, the perfluorinated surfactant exhibits a lesser transport effect than the hydrocarbon surfactant.

  19. INTERRELATION OF RHOMBICITY AND OCCURRENCE OF INTERNAL CRACKS AT CONTINUOUS CASTING OF SORTED SLUG

    Directory of Open Access Journals (Sweden)

    Ju. A. Samojlovich

    2008-01-01

    Full Text Available Analysis of deformations and stresses in cross section of sorted uninterruptedly-casted slugs at their solidification and cooling within limits of crystallizer with the aim of determination of possibilities for occurrence of internal cracks of diagonal type is carried out on basis of mathematical modeling, the peculiarities of the slug skin cooling at its shrinkage and separation from crystallizer wall are revealed.

  20. Experimental study for the stratified to slug flow regime transition mechanism of gas-oil two-phase flow in horizontal pipe

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Theoretical relations that predict the transition from a stratified pattern to a slug pattern,including a onedimensional wave model that contains less empiricism than the commonly used Taitel-Dukler model,and the ideal model for stratified flow for the gas-liquid flow in horizontal pipes are presented.Superficial velocities of each phase,as the onset of slugging occurs,were predicted,and theoretical analysis was conducted on the stratified to slug flow regime transition.The friction,existing between the fluid and pipe wall,and on the interface of two phases,was especially taken into account.A theoretical model was applied to an experiment about air-oil two-phase flow in a 50 mm horizontal pipe.The effect of pipe diameter on the transition was also studied.The results show that this approach gives a reasonable prediction over the whole range of flow rates,and better agreement has been achieved between predicted and measured critical parameters.

  1. RCP induces Slug expression and cancer cell invasion by stabilizing β1 integrin.

    Science.gov (United States)

    Hwang, M H; Cho, K H; Jeong, K J; Park, Y-Y; Kim, J M; Yu, S-L; Park, C G; Mills, G B; Lee, H Y

    2017-02-23

    Rab coupling protein (RCP)-induced tumor cell migration has been implicated in tumor pathophysiology and patient outcomes. In the present study, we demonstrate that RCP stabilizes β1 integrin leading to increased β1 integrin levels and activation of a signaling cascade culminating in Slug induction, epithelial-to-mesenchymal transition and increased invasion. Ectopic expression of RCP induced Slug expression. Silencing β1 integrin efficiently inhibited RCP-induced Slug expression and subsequent cancer cell invasion. Conversely, ectopic expression of β1 integrin was sufficient to induce Slug expression. Pharmacological inhibition of integrin linked kinase (ILK), EGFR and NF-κB, as well as transfection of a dominant-negative mutant of Ras (RasN17), significantly inhibited RCP-induced Slug expression and cancer cell invasion. Strikingly, ectopic expression of RCP was sufficient to enhance metastasis of ovarian cancer cells to the lung. Collectively, we demonstrate a mechanism by which RCP promotes cancer cell aggressiveness through sequential β1 integrin stabilization, activation of an ILK/EGFR/Ras/NF-κB signaling cascade and subsequent Slug expression.

  2. Integrity of high-velocity water slug generated by an impacting technique

    Science.gov (United States)

    Dehkhoda, Sevda; Bourne, Neil

    2013-06-01

    A pulsed water jet is a series of discrete water slugs travelling at high velocity. Immediately after striking a target, these slugs apply high-intensity, short-duration transient stress known as the water hammer pressure, followed by low-intensity, long-duration stationary stress at the stagnation pressure. The magnitude and duration of the water hammer and stagnation pressures are controlled by the size and quality of the water slugs. The use of water jets for rock cutting in mining operations is a centuries-old technology; however, practical methods for producing high-energy water slugs repeatedly have proven difficult. This can be partly due to the fact that the geometrical properties of a jet and so its effectiveness in creating damage is controlled and influenced by the method that is employed to generate the water slugs. This paper investigates the integrity of a single water slug produced using an impacting technique where a hammer strikes a piston, resting on top of a water-filled chamber. The coherence of the generated water pulse was of concern in this study. If repeated shock reflections within the chamber were transmitted or were carried into the internal geometry of nozzle, the emerging jet could pulsate. The impact impulse of the formed water jet was measured in a Kel-F target material using an embedded PVDF (Polyvinylidene fluoride) shock gauge. The recorded stress waveform was then used to study the quality and endurance of the water pulse stream as it travelled through air.

  3. Polymorphisms of the maternal Slug gene in fetal neural tube defects in a Chinese population

    Institute of Scientific and Technical Information of China (English)

    Li Guo; Hong Zhao; Yuheng Pei; Quanren He; Wan-I Li; Ting Zhang; Xiaoying Zheng; Ran Zhou; Jun Xie

    2010-01-01

    Several studies have demonstrated that Slug,which encodes a zinc finger of the Snail family of transcription factors,is a potential risk factor for neural tube defects.Neural tube defects tend to occur with a high rate in Shanxi province,China.The present case-control study investigated genotypic distributions and allele frequencies of Slug C1548A polymorphisms in DNA samples from59 women with a history of neural tube defect pregnancies and 73 controls during the same period from Shanxi Province,China.Results demonstrated that women with a history of neural tube defect pregnancies had significantly greater genotypic distributions of Slug AA genotypes and A allele frequencies compared with controls,and A allele Slug C1548A was a risk factor for neural tube defects(odds ratio = 3.444;95% confidence interval;2.021-5.868,P < 0.05).Three-dimensional structure prediction revealed that Slug C1548A resulted in transition of aspartic acid into glutamate at position 119.This indicated that these mutations could lead to damaged protein structure and function.These findings suggest that Slug C1548A gene polymorphism is closely related to neural tube defects in a population of Han Chinese origin from Shanxi Province,China

  4. Slug tests in wells screened across the water table: some additional considerations.

    Science.gov (United States)

    Butler, J J

    2014-01-01

    The majority of slug tests done at sites of shallow groundwater contamination are performed in wells screened across the water table and are affected by mechanisms beyond those considered in the standard slug-test models. These additional mechanisms give rise to a number of practical issues that are yet to be fully resolved; four of these are addressed here. The wells in which slug tests are performed were rarely installed for that purpose, so the well design can result in problematic (small signal to noise ratio) test data. The suitability of a particular well design should thus always be assessed prior to field testing. In slug tests of short duration, it can be difficult to identify which portion of the test represents filter-pack drainage and which represents formation response; application of a mass balance can help confirm that test phases have been correctly identified. A key parameter required for all slug test models is the casing radius. However, in this setting, the effective casing radius (borehole radius corrected for filter-pack porosity), not the nominal well radius, is required; this effective radius is best estimated directly from test data. Finally, although conventional slug-test models do not consider filter-pack drainage, these models will yield reasonable hydraulic conductivity estimates when applied to the formation-response phase of a test from an appropriately developed well.

  5. Distribution of void fraction for gas-liquid slug flow in an inclined pipe

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    In order to investigate the effect of inclination angle on the spatial distribution of phases, experiments on gas-liquid two-phase slug flow in an inclined pipe were carried out by using the optical probe and an EKTAPRO 1000 high speed motion analyzer. It has been demonstrated that the inclination angle and the mixture velocity are important parameters to influence the distribution of void fraction for upward slug flow in the inclined pipe. At high mixture velocity, the gas phase profile is axial symmetry in the cross-section of the pipe. This is similar to that for vertical slug flow. In contrast, most of the gas phase is located near the upper pipe wall at low mixture velocity. By measuring the axial variation of void fraction along the liquid slug, it can be concluded that there is a high void fraction wake region with length of 3~4D in the front of liquid slug. In the fully developed zone of liquid slug, the peak value of the void fraction is near the upper wall.

  6. An NF-kappaB and slug regulatory loop active in early vertebrate mesoderm.

    Directory of Open Access Journals (Sweden)

    Chi Zhang

    Full Text Available BACKGROUND: In both Drosophila and the mouse, the zinc finger transcription factor Snail is required for mesoderm formation; its vertebrate paralog Slug (Snai2 appears to be required for neural crest formation in the chick and the clawed frog Xenopus laevis. Both Slug and Snail act to induce epithelial to mesenchymal transition (EMT and to suppress apoptosis. METHODOLOGY & PRINCIPLE FINDINGS: Morpholino-based loss of function studies indicate that Slug is required for the normal expression of both mesodermal and neural crest markers in X. laevis. Both phenotypes are rescued by injection of RNA encoding the anti-apoptotic protein Bcl-xL; Bcl-xL's effects are dependent upon IkappaB kinase-mediated activation of the bipartite transcription factor NF-kappaB. NF-kappaB, in turn, directly up-regulates levels of Slug and Snail RNAs. Slug indirectly up-regulates levels of RNAs encoding the NF-kappaB subunit proteins RelA, Rel2, and Rel3, and directly down-regulates levels of the pro-apopotic Caspase-9 RNA. CONCLUSIONS/SIGNIFICANCE: These studies reveal a Slug/Snail-NF-kappaB regulatory circuit, analogous to that present in the early Drosophila embryo, active during mesodermal formation in Xenopus. This is a regulatory interaction of significance both in development and in the course of inflammatory and metastatic disease.

  7. 微电解法预处理高浓度阴离子表面活性剂废水%Pretreatment of wastewater containing highly concentrated anionic surfactant by micro-electrolysis

    Institute of Scientific and Technical Information of China (English)

    文善雄; 梁宝锋; 徐静; 荣树茂

    2011-01-01

    考察了不同微电解方式对含高浓度阴离子表面活性剂(AS)废水的预处理效果,结果表明,在铁炭填料分别为F3(铁屑,规格3 mm×10 mm)、C3(活性炭,规格D 2 mm×3 mm),进水pH为3.5,停留时间为30 min的相同条件下,当m(F3):m(C3)=2:1时,二元微电解法对废水AS及COD的平均去除率分别为51.32%、48.9%;当m(F3):m(Cu):m(C3)=60:60:40时,三元微电解法对废水AS及COD的平均去除率分别为54.14%、49.0%.从处理效果和实际工程应用综合考虑,选用二元微电解法预处理该废水.%The pretreatment effect of the wastewater containing highly concentrated anionic surfactant (AS) by different micro-electrolysis modes has been investigated. The results show that under the same conditions: the mass ratio of F3 (iron,size 3 mmxlO mm) and C3 (activated carbon,size D 2 mmx3 mm) is 2:1, pH 3.5 and retention time 30 min,the average removing rates of AS and COD are 51.32% and 48.9% Respectively by binary micro-electrolysis. When the mass ratio of F3、Cu and C3 is 60:60=40,the average removing rates of AS and COD are 54.14% and 49.0% Respectively by ternary micro-electrolysis. Out of consideration for the treatment effectiveness and actual application, the binary micro-electrolysis should be selected for the pretreatment of such wastewater.

  8. Surfactant-Amino Acid and Surfactant-Surfactant Interactions in Aqueous Medium: a Review.

    Science.gov (United States)

    Malik, Nisar Ahmad

    2015-08-01

    An overview of surfactant-amino acid interactions mainly in aqueous medium has been discussed. Main emphasis has been on the solution thermodynamics and solute-solvent interactions. Almost all available data on the topic has been presented in a lucid and simple way. Conventional surfactants have been discussed as amphiphiles forming micelles and amino acids as additives and their effect on the various physicochemical properties of these conventional surfactants. Surfactant-surfactant interactions in aqueous medium, various mixed surfactant models, are also highlighted to assess their interactions in aqueous medium. Finally, their applied part has been taken into consideration to interpret their possible uses.

  9. Interaction of photosensitive surfactant with DNA and poly acrylic acid

    Energy Technology Data Exchange (ETDEWEB)

    Zakrevskyy, Yuriy, E-mail: yuriy.zakrevskyy@fh-koeln.de; Paasche, Jens; Lomadze, Nino; Santer, Svetlana, E-mail: santer@uni-potsdam.de [Experimental Physics, Institute of Physics and Astronomy, University of Potsdam, Karl-Liebknecht-Str. 24-25, D-14476 Potsdam (Germany); Cywinski, Piotr; Cywinska, Magdalena; Reich, Oliver; Löhmannsröben, Hans-Gerd [Physical Chemistry, Institute of Chemistry, University of Potsdam, Karl-Liebknecht-Str. 24-25, D-14476 Potsdam (Germany)

    2014-01-28

    In this paper, we investigate interactions and phase transitions in polyelectrolyte-surfactant complexes formed between a cationic azobenzene-containing surfactant and two types of polyelectrolytes: natural (DNA) or synthetic (PAA: poly acrylic acid). The construction of a phase diagram allowed distancing between four major phases: extended coil conformation, colloidally stable compacted globules, colloidal instability range, and surfactant-stabilized compact state. Investigation on the complexes’ properties in different phases and under irradiation with UV light provides information about the role of the surfactant's hydrophobic trans isomers both in the formation and destruction of DNA and PAA globules as well as in their colloidal stabilization. The trans isomer shows much stronger affinity to the polyelectrolytes than the hydrophilic cis counterpart. There is no need for complete compensation of the polyelectrolyte charges to reach the complete compaction. On contrary to the findings previously reported in the literature, we demonstrate – for the first time – complete polyelectrolyte compaction which occurs already at 20% of DNA (and at 50% of PAA) charge compensation. The trans isomer plays the main role in the compaction. The aggregation between azobenzene units in the photosensitive surfactant is a driving force of this process. The decompaction can be realized during UV light irradiation and is strongly influenced by the interplay between surfactant-surfactant and surfactant-DNA interactions in the compacted globules.

  10. Interaction of photosensitive surfactant with DNA and poly acrylic acid

    Science.gov (United States)

    Zakrevskyy, Yuriy; Cywinski, Piotr; Cywinska, Magdalena; Paasche, Jens; Lomadze, Nino; Reich, Oliver; Löhmannsröben, Hans-Gerd; Santer, Svetlana

    2014-01-01

    In this paper, we investigate interactions and phase transitions in polyelectrolyte-surfactant complexes formed between a cationic azobenzene-containing surfactant and two types of polyelectrolytes: natural (DNA) or synthetic (PAA: poly acrylic acid). The construction of a phase diagram allowed distancing between four major phases: extended coil conformation, colloidally stable compacted globules, colloidal instability range, and surfactant-stabilized compact state. Investigation on the complexes' properties in different phases and under irradiation with UV light provides information about the role of the surfactant's hydrophobic trans isomers both in the formation and destruction of DNA and PAA globules as well as in their colloidal stabilization. The trans isomer shows much stronger affinity to the polyelectrolytes than the hydrophilic cis counterpart. There is no need for complete compensation of the polyelectrolyte charges to reach the complete compaction. On contrary to the findings previously reported in the literature, we demonstrate - for the first time - complete polyelectrolyte compaction which occurs already at 20% of DNA (and at 50% of PAA) charge compensation. The trans isomer plays the main role in the compaction. The aggregation between azobenzene units in the photosensitive surfactant is a driving force of this process. The decompaction can be realized during UV light irradiation and is strongly influenced by the interplay between surfactant-surfactant and surfactant-DNA interactions in the compacted globules.

  11. Photocontrol of fluid slugs in liquid crystal polymer microactuators

    Science.gov (United States)

    Lv, Jiu-An; Liu, Yuyun; Wei, Jia; Chen, Erqiang; Qin, Lang; Yu, Yanlei

    2016-09-01

    The manipulation of small amounts of liquids has applications ranging from biomedical devices to liquid transfer. Direct light-driven manipulation of liquids, especially when triggered by light-induced capillary forces, is of particular interest because light can provide contactless spatial and temporal control. However, existing light-driven technologies suffer from an inherent limitation in that liquid motion is strongly resisted by the effect of contact-line pinning. Here we report a strategy to manipulate fluid slugs by photo-induced asymmetric deformation of tubular microactuators, which induces capillary forces for liquid propulsion. Microactuators with various shapes (straight, ‘Y’-shaped, serpentine and helical) are fabricated from a mechanically robust linear liquid crystal polymer. These microactuators are able to exert photocontrol of a wide diversity of liquids over a long distance with controllable velocity and direction, and hence to mix multiphase liquids, to combine liquids and even to make liquids run uphill. We anticipate that this photodeformable microactuator will find use in micro-reactors, in laboratory-on-a-chip settings and in micro-optomechanical systems.

  12. Stability Analysis of Reactive Multiphase Slug Flows in Microchannels

    Directory of Open Access Journals (Sweden)

    Alejandro A. Munera Parra

    2014-05-01

    Full Text Available Conducting multiphase reactions in micro-reactors is a promising strategy for intensifying chemical and biochemical processes. A major unresolved challenge is to exploit the considerable benefits offered by micro-scale operation for industrial scale throughputs by numbering-up whilst retaining the underlying advantageous flow characteristics of the single channel system in multiple parallel channels. Fabrication and installation tolerances in the individual micro-channels result in different pressure losses and, thus, a fluid maldistribution. In this work, an additional source of maldistribution, namely the flow multiplicities, which can arise in a multiphase reactive or extractive flow in otherwise identical micro-channels, was investigated. A detailed experimental and theoretical analysis of the flow stability with and without reaction for both gas-liquid and liquid-liquid slug flow has been developed. The model has been validated using the extraction of acetic acid from n-heptane with the ionic liquid 1-Ethyl-3-methylimidazolium ethyl sulfate. The results clearly demonstrate that the coupling between flow structure, the extent of reaction/extraction and pressure drop can result in multiple operating states, thus, necessitating an active measurement and control concept to ensure uniform behavior and optimal performance.

  13. Adsorption and intercalation of anionic surfactants onto layered double hydroxides—XRD study

    Indian Academy of Sciences (India)

    R Anbarasan; W D Lee; S S Im

    2005-04-01

    Layered double hydroxides (LDH) with brucite like structure was modified with various anionic surfactants containing sulfonate, carboxyl, phosphonate and sulfate end group through ion-exchange method. XRD reports indicated that the sulfonate group containing surfactants led to an adsorption process whereas the sulfate, carboxyl and phosphonate group containing surfactant led to an intercalation process. This can be evidenced from the change in basal spacing of LDH. The presence of anionic surfactants in the LDH was supported by FTIR spectroscopy. The FTIR spectrum indicated that complete removal of carbonate anion from the inter layer space of LDH is very difficult. The phosphonate intercalated HT showed less thermal stability than pristine LDH.

  14. Development of cost-effective surfactant flooding technology. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Pope, G.A.; Sepehrnoori, K.

    1996-11-01

    Task 1 of this research was the development of a high-resolution, fully implicit, finite-difference, multiphase, multicomponent, compositional simulator for chemical flooding. The major physical phenomena modeled in this simulator are dispersion, heterogeneous permeability and porosity, adsorption, interfacial tension, relative permeability and capillary desaturation, compositional phase viscosity, compositional phase density and gravity effects, capillary pressure, and aqueous-oleic-microemulsion phase behavior. Polymer and its non-Newtonian rheology properties include shear-thinning viscosity, permeability reduction, inaccessible pore volume, and adsorption. Options of constant or variable space grids and time steps, constant-pressure or constant-rate well conditions, horizontal and vertical wells, and multiple slug injections are also available in the simulator. The solution scheme used in this simulator is fully implicit. The pressure equation and the mass-conservation equations are solved simultaneously for the aqueous-phase pressure and the total concentrations of each component. A third-order-in-space, second-order-in-time finite-difference method and a new total-variation-diminishing (TVD) third-order flux limiter are used that greatly reduce numerical dispersion effects. Task 2 was the optimization of surfactant flooding. The code UTCHEM was used to simulate surfactant polymer flooding.

  15. Development of cost-effective surfactant flooding technology. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Pope, G.A.; Sepehrnoori, K.

    1996-11-01

    Task 1 of this research was the development of a high-resolution, fully implicit, finite-difference, multiphase, multicomponent, compositional simulator for chemical flooding. The major physical phenomena modeled in this simulator are dispersion, heterogeneous permeability and porosity, adsorption, interfacial tension, relative permeability and capillary desaturation, compositional phase viscosity, compositional phase density and gravity effects, capillary pressure, and aqueous-oleic-microemulsion phase behavior. Polymer and its non-Newtonian rheology properties include shear-thinning viscosity, permeability reduction, inaccessible pore volume, and adsorption. Options of constant or variable space grids and time steps, constant-pressure or constant-rate well conditions, horizontal and vertical wells, and multiple slug injections are also available in the simulator. The solution scheme used in this simulator is fully implicit. The pressure equation and the mass-conservation equations are solved simultaneously for the aqueous-phase pressure and the total concentrations of each component. A third-order-in-space, second-order-in-time finite-difference method and a new total-variation-diminishing (TVD) third-order flux limiter are used that greatly reduce numerical dispersion effects. Task 2 was the optimization of surfactant flooding. The code UTCHEM was used to simulate surfactant polymer flooding.

  16. Novel method for non-intrusive measurement of velocity and slug length in two- and three-phase slug flow in capillaries

    NARCIS (Netherlands)

    Wolffenbuttel, BMA; Nijhuis, TA; Stankiewicz, A; Moulijn, JA

    2002-01-01

    A method was developed for the measurement of velocity and slug length of two and three-phase flow in capillaries. The method consists of the combination of an impedance meter and two IR sensors. Non-intrusive measurement of the velocity can be performed with the IR sensors in gas-liquid and gas-liq

  17. The effect of surfactant on pollutant biosorption of Trametes versicolor

    Science.gov (United States)

    Gül, Ülküye Dudu; Silah, Hülya; Akbaş, Halide; Has, Merve

    2016-04-01

    The major problem concerning industrial wastewater is treatment of dye and heavy metal containing effluents. Industrial effluents are also contained surfactants that are used as levelling, dispersing and wetting agents. The purpose of this study was to investigate the effect of surfactant on textile dye biosorption properties of a white rot fungus named Trametes versicolor. Reactive dyes are commonly used in textile industry because of their advantages such as brightness and excellent color fastness. A recative textile dye, called Everzol Black, was used in this study. The low-cost mollasses medium is used for fungal growth. The usage of mollases, the sugar refinery effluent as a source of energy and nutrients, gained importance because of reducing the cost and also reusing another waste. In biosorption process the effect of surfactant on dye removal properties of T. versicolor was examined as a function of pH, dye consentration and surfactant concentration. The results of this study showed that the surfactant enhanced the dye removal capacity of Trametes versicolor. The dye and surfactant molecules were interacted electrostatically and these electrostatic interactions improved dye removal properties of filamentous fungus T. versicolor. The results of this study recommended the use of surfactants as an inducer in textile wastewater treatment technologies.

  18. Slug responses to grassland cutting and fertilizer application under plant functional group removal

    Science.gov (United States)

    Everwand, Georg; Scherber, Christoph; Tscharntke, Teja

    2013-04-01

    Current studies on trophic interactions in biodiversity experiments have largely relied on artificially sown gradients in plant diversity, but removal experiments with their more natural plant community composition are more realistic. Slugs are a major part of the invertebrate herbivore community, with some species being common pests in agriculture. We therefore investigated how strongly slugs are influenced by grassland management, plant biodiversity and composition. Here we analysed the effects of cutting frequency, fertilizer application and plant functional group composition on slug densities and their contribution to herbivory on Rumex acetosa in a removal experiment within a >100-year old grassland in Northern Germany. The experiment was laid out as a Latin rectangle with full factorial combinations of (i) plant functional group removal (3 levels) using herbicides, (ii) fertilizer application (2 levels) and (iii) cutting frequency (2 levels). The resulting 12 treatment combinations were replicated 6 times, resulting in 72 plots. We collected a total of 1020 individuals belonging to three species Arion distinctus (60.4% of individuals), Deroceras reticulatum (34.7%) and Arion lusitanicus (4.9%) using a cover board technique and additionally measured herbivore damage to R. acetosa. We found the highest slug abundance on plots with a low cutting frequency and high food resource availability (increased cover of forbs and taller vegetation). Fertilizer application had no significant effect on slug abundance, but caused higher herbivore damage to on R. acetosa, possibly as a result of increased tissue quality. The negative effect of higher cutting frequency on slug abundance was lowest in control plots with their naturally developed graminoid-forb communities (cutting reduced slug density by 6% in the control vs. 29% in herbicide plots). Our experiments therefore support the idea that more natural plant species compositions reduce the impact of disturbances (e

  19. Oil Recovery of Soil Contained Petroleum Oil by Using Bio surfactant of Mixed Cultures Bacteria (Brevundumonas diminuta, Pseudomonas fluorescens, Pseudomonas aeroginosa, Pseudomonas citronelis at vary pH Conditions (5-9

    Directory of Open Access Journals (Sweden)

    Bambang Yudono

    2017-06-01

    Full Text Available Abstract The bacteria (Brevundumonas diminuta, Pseudomonas fluorescens, Pseudomonas aeroginosa, Pseudomonas citronelbis which are indigenous bacteria from Babat Toman village South Sumatra. It were isolated and identified by using Bergey's method. In the normal condition (pH 7, these bacteria could produce bio surfactant and effectively as mixed culture. The growth of mixed culture of indigenous bacteria was tested at different pH conditions (5-9. The results show that  the optimum pH was obtained at pH 7, the population of bacteria was  2.14.107 cfu/mL. The shortest regeneration time of these bacteria were (12, 12, 9, 9 hours respectively. The initial total petroleum hydrocarbon concentration of sample was 18,4 %, it was extracted by using the bio surfactant of mixed culture with 10 % concentration at different pH conditions (5-9, the contact time as long as 168 hours. The optimal oil recovery was obtained at pH 7 as much as 20.97 %. It can be concluded that the bio surfactant effectively used in the normal condition (pH 7 and ineffectively in alkaline condition (pH 9.The GC analyses were conducted to initial crude oil and the residue. The results show that the crude oil consists of 33 components, and the residue consists of 14 components. It shows that the bio surfactant of mixed culture bacteria dissolved the hydrocarbon components with temperature fractions 150, 155, 178, 184, 190, and 197 o C.  

  20. Amino acid–based surfactants: New antimicrobial agents.

    Science.gov (United States)

    Pinazo, A; Manresa, M A; Marques, A M; Bustelo, M; Espuny, M J; Pérez, L

    2016-02-01

    The rapid increase of drug resistant bacteria makes necessary the development of new antimicrobial agents. Synthetic amino acid-based surfactants constitute a promising alternative to conventional antimicrobial compounds given that they can be prepared from renewable raw materials. In this review, we discuss the structural features that promote antimicrobial activity of amino acid-based surfactants. Monocatenary, dicatenary and gemini surfactants that contain different amino acids on the polar head and show activity against bacteria are revised. The synthesis and basic physico-chemical properties have also been included.

  1. Sizing up surfactant synthesis.

    Science.gov (United States)

    Han, SeungHye; Mallampalli, Rama K

    2014-08-01

    Phosphatidylcholine is generated through de novo synthesis and remodeling involving a lysophospholipid. In this issue of Cell Metabolism, research from the Shimizu lab (Harayama et al., 2014) demonstrates the highly selective enzymatic behavior of lysophospholipid acyltransferases. The authors present an enzymatic model for phosphatidylcholine molecular species diversification that impacts surfactant formation.

  2. Perfluorinated Alcohols Induce Complex Coacervation in Mixed Surfactants.

    Science.gov (United States)

    Jenkins, Samuel I; Collins, Christopher M; Khaledi, Morteza G

    2016-03-15

    Recently, we reported a unique and nearly ubiquitous phenomenon of inducing simple and complex coacervation in solutions of a broad variety of individual and mixed amphiphiles and over a wide range of concentrations and mole fractions. This paper describes a novel type of biphasic separation in aqueous solutions of mixed cationic-anionic (catanionic) surfactants induced by hexafluoroisopropanol (HFIP). The test cases included mixtures of cetyltrimethylammonium bromide (CTAB) and sodium dodecyl sulfate (SDS) (surfactants with different carbon chain lengths) as well as dodecyltrimethylammonium bromide (DTAB) with SDS (surfactants with the same carbon chain lengths). The CTAB-SDS-HFIP coacervate systems can be produced at many different mole ratios of surfactant, but DTAB-SDS-HFIP formed only coacervates at equimolar (1:1) mole ratios of DTAB and SDS. The phase-transition behavior of both systems was studied over a wide range of surfactant and HFIP concentrations at the stoichiometric (1:1) mole ratio of cationic/anionic surfactants. The chemical compositions of each of the two phases (aqueous-rich and coacervate phases) were studied with regard to the concentrations of HFIP, water, and individual surfactants. It is revealed that the surfactant-rich phase (coacervate phase) contains a large percentage of fluoroalcohol relative to the aqueous phase and is enriched in both surfactants but contains a small percentage of water. Surprisingly, the concentration of water in the coacervate phase increases as the total HFIP concentration is increased while the concentration of HFIP in the coacervate phase remains relatively constant, which means a larger amount of water associated with HFIP molecules is extracted into the coacervate phase, which results in the growth of the phase. The volume of the coacervate phase increases with an increase in surfactant concentration and total HFIP %. The coacervate phase is highly enriched in the two amphiphilic ions (DTA(+) and DS

  3. Influence of Catalysis and Oxidation on Slug Calorimeter Measurements in Arc Jets

    Science.gov (United States)

    Nawaz, Anuscheh; Driver, Dave; TerrazasSalinas, Imelda

    2012-01-01

    Arc jet tests play a critical role in the characterization and certification of thermal protection materials and systems (TPS). The results from these arc jet tests feed directly into computational models of material response and aerothermodynamics to predict the performance of the TPS in flight. Thus the precise knowledge of the plasma environment to which the test material is subjected, is invaluable. As one of the environmental parameters, the heat flux is commonly measured. The measured heat flux is used to determine the plasma enthalpy through analytical or computational models. At NASA Ames Research Center (ARC), slug calorimeters of a geometrically similar body to the test article are routinely used to determine the heat flux. A slug calorimeter is a thermal capacitance-type calorimeter that uses the temperature rise in a thermally insulated slug to determine the heat transfer rate, see Figure 1(left). Current best practices for measuring the heat flux with a slug calorimeter are described in ASTM E457 - 96. Both the calorimeter body and slug are made of Oxygen Free High Conductivity Copper, and are cleaned before each run.

  4. Evaluation of near-critical overdamping effects in slug-test response.

    Science.gov (United States)

    Weeks, E P; Clark, A C

    2013-01-01

    A slug test behaves as a harmonic oscillator, subject to both inertial effects and viscous damping. When viscous and inertial forces are closely balanced, the system is nearly critically damped, and water-level recovery is affected by inertial effects, but does not exhibit oscillation. These effects were investigated by use of type curves, generated both by modification of Kipp's (1985) computer program and by use of the Butler-Zhan (2004) model. Utility of the type curves was verified by re-analysis of the Regina slug test previously analyzed by Kipp. These type curves indicate that near-critical inertial effects result in early-time delayed water-level response followed by merger with, or more rapid recovery than, response for the fully damped case. Because of this early time response, slug tests in the moderately over-damped range are best analyzed using log-log type curves of (1 - H/H(0)) vs. Tt/r(2c). Failure to recognize inertial effects in slug test data could result in an over-estimate of transmissivity, and a too-small estimate of storage coefficient or too-large estimate of well skin. However, application of the widely used but highly empirical Hvorslev (1951) method to analyze both the Regina slug test and type-curve generated data indicate that such analyses provide T values within a factor of 2 of the true value.

  5. Snail/Slug-YAP/TAZ complexes cooperatively regulate mesenchymal stem cell function and bone formation.

    Science.gov (United States)

    Tang, Yi; Weiss, Stephen J

    2017-03-04

    Snail and Slug are zinc-finger transcription factors that play key roles in directing the epithelial-mesenchymal transition (EMT) programs associated with normal development as well as disease progression. More recent work suggests that these EMT-associated transcription factors also modulate the function of both embryonic and adult stem cells. Interestingly, YAP and TAZ, the co-transcriptional effectors of the Hippo pathway, likewise play an important role in stem cell self-renewal and lineage commitment. While direct intersections between the Snail/Slug and Hippo pathways have not been described previously, we recently described an unexpected cooperative interaction between Snail/Slug and YAP/TAZ that controls the self-renewal and differentiation properties of bone marrow-derived mesenchymal stem cells (MSCs), a cell population critical to bone development. Additional studies revealed that both Snail and Slug are able to form binary complexes with either YAP or TAZ that, together, control YAP/TAZ transcriptional activity and function throughout mouse development. Given the more recent observations that MSC-like cell populations are found in association throughout the vasculature where they participate in tissue regeneration, fibrosis and cancer, the Snail/Slug-YAP/TAZ axis is well-positioned to regulate global stem cell function in health and disease.

  6. Modelling and control of growing slugs in horizontal multiphase pipe flows

    Directory of Open Access Journals (Sweden)

    Steinar M. Elgsæter

    2006-07-01

    Full Text Available In this paper, the use of active control to restrict the length of growing slugs in horizontal pipelines is investigated. Specifically, the paper attempts to determine if such control can be attained with realistic measurements and actuators. Simulations in OLGA2000 show that a feedback controller can use measurements or estimates of slug length to control the growth of a slug in a horizontal pipeline by partially closing inlet or outlet chokes. A control-volume approach is used to develop a low-order model of inlet choke-slug growth dynamics based on mass- and impulse balances. The resulting model is a system of nonlinear differential-algebraic equations, which is suitable for observer-design. The tuned model is found to be in good agreement with experiments and OLGA2000-simulations. Linearizations of the model are found to be observable around realistic trajectories when rates and pressures at the inlet and outlet are measured. An extended Luenberger-observer is shown to give good estimates of slug length and -position in simulations even under model uncertainty.

  7. Slug tuner effect on the field stabilization of the drift tube linac

    Science.gov (United States)

    Kim, Han-Sung

    2015-02-01

    In a drift tube linac (DTL), the accelerating field is stabilized against external perturbation, through resonant coupling between each cell by using post couplers. For proper field stabilization tuning, the frequency band between the post mode and the cavity mode should be closed. In addition, the field profile along the beam axis of the highest post mode should be similar to that of the TM011 cavity mode. As a conventional method to correct the resonance frequency and to make the accelerating field flat, slug tuners are incorporated. We observed that the similarity of field profiles between the highest post mode and the TM011 cavity mode disappeared when the slug tuners were inserted too much into the DTL tank. To achieve field stabilization tuning, we limited the slug tuner insertion and used a tuning ring around each post coupler to tune the resonant frequency of the DTL tank. The details of the effect of a slug tuner on the field stabilization tuning and the solution to the resonant frequency tuning problem caused by limited slug insertion will be presented in this paper.

  8. An Investigation on the Void Fraction for upward Gas-Liquid Slug Flow in Vertical Pipe

    Institute of Scientific and Technical Information of China (English)

    夏国栋; 周芳德; 胡明胜

    2001-01-01

    In order to investigate the influence of the entrance effect on the spatial distribution of phases, the experiments on gas-liquid two-phase slug flow in a vertical pipe of 0.03m ID were carried out by using optical probes and an EKTAPRO 1000 high speed motion analyzer. It demonstrates that the radial profile of slug flow void fraction is parabolic. Influenced by the falling liquid film, the radial profile curve of liquid slug void fraction in the wake region is also parabolic. Since fully turbulent velocity distribution is built up in the developed region,the void fraction profile in this region is the saddle type. At given superficial liquid velocity, the liquid slug void fraction increases with gas velocity. The radial profiles of liquid slug void fraction at different axial locations are all saddle curves, but void fraction is obviously high around the centerline in the entrance region. The nearer the measuring station is from the entrance, the farther the peak location is away from the wall.

  9. Water slug formation and motion in gas flow channels: the effects of geometry, surface wettability, and gravity.

    Science.gov (United States)

    Cheah, May J; Kevrekidis, Ioannis G; Benziger, Jay B

    2013-08-06

    Water emerging from ∼100 μm pores into millimeter-size gas flow channels forms drops that grow and become slugs which span the flow channel. Flowing gas causes the slugs to detach and move down the channel. The effect of channel geometry, surface wettability, and gravity on the formation and motion of water slugs has been analyzed using high-speed video images of the drops and differential pressure-time traces. Drops grow and appear, assuming a sequence of shapes that minimize the total interfacial energy of the gas-liquid and liquid-solid interfaces. The drops are initially spherical caps centered on the pore (the liquid contacts one wall). Above a certain size, the drops move to the corner, forming "corner drops" (the liquid contacts two walls). Corner drops grow across the channel, evolving into partial liquid bridges (drops confined by three walls), and finally the drops span the channel cross-section forming slugs (contacting all four walls). Smaller slugs are formed in channels with hydrophobic walls than in channels with hydrophilic walls. Smaller slugs are formed in channels with curved walls than in square or rectangular channels. Slugs move when the differential gas pressure overcomes the force to move the advancing and receding gas-liquid-solid contact lines of the slugs. Residual water left behind in corners by moving slugs reduces the barriers for drops to form slugs, causing the steady-state slug volumes to be smaller than those seen at start-up in dry channels.

  10. Hydrogels of sodium alginate in cationic surfactants: Surfactant dependent modulation of encapsulation/release toward Ibuprofen.

    Science.gov (United States)

    Jabeen, Suraya; Chat, Oyais Ahmad; Maswal, Masrat; Ashraf, Uzma; Rather, Ghulam Mohammad; Dar, Aijaz Ahmad

    2015-11-20

    The interaction of cetyltrimethylammoium bromide (CTAB) and its gemini homologue (butanediyl-1,4-bis (dimethylcetylammonium bromide), 16-4-16 with biocompatible polymer sodium alginate (SA) has been investigated in aqueous medium. Addition of K2CO3 influences viscoelastic properties of surfactant impregnated SA via competition between electrostatic and hydrophobic interactions. Viscosity of these polymer-surfactant systems increases with increase in concentration of K2CO3, and a cryogel is formed at about 0.5M K2CO3 concentration. The thermal stability of gel (5% SA+0.5M K2CO3) decreases with increase in surfactant concentration, a minimum is observed with increase in 16-4-16 concentration. The impact of surfactant addition on the alginate structure vis-à-vis its drug loading capability and release thereof was studied using Ibuprofen (IBU) as the model drug. The hydrogel with 16-4-16 exhibits higher IBU encapsulation and faster release in comparison to the one containing CTAB. This higher encapsulation-cum-faster release capability has been related to micelle mediated solubilization and greater porosity of the hydrogel with gemini surfactant.

  11. Rheology of cellulose nanofibrils in the presence of surfactants.

    Science.gov (United States)

    Quennouz, Nawal; Hashmi, Sara M; Choi, Hong Sung; Kim, Jin Woong; Osuji, Chinedum O

    2016-01-07

    Cellulose nanofibrils (CNFs) present unique opportunities for rheology modification in complex fluids. Here we systematically consider the effect of ionic and non-ionic surfactants on the rheology of dilute CNF suspensions. Neat suspensions are transparent yield-stress fluids which display strong shear thinning and power-law dependence of modulus on concentration, G' ∼ c(2.1). Surfactant addition below a critical mass concentration cc produces an increase in the gel modulus with retention of optical clarity. Larger than critical concentrations induce significant fibril aggregation leading to the loss of suspension stability and optical clarity, and to aggregate sedimentation. The critical concentration was the lowest for a cationic surfactant (DTAB), cc ≈ 0.08%, while suspension stability was retained for non-ionic surfactants (Pluronic F68, TX100) at concentrations up to 8%. The anionic surfactant SDS led to a loss of stability at cc ≈ 1.6% whereas suspension stability was not compromised by anionic SLES up to 8%. Dynamic light scattering data are consistent with a scenario in which gel formation is driven by micelle-nanofibril bridging mediated by associative interactions of ethoxylated surfactant headgroups with the cellulose fibrils. This may explain the strong difference between the properties of SDS and SLES-modified suspensions. These results have implications for the use of CNFs as a rheology modifier in surfactant-containing systems.

  12. Sublethal effect of agronomical surfactants on the spider Pardosa agrestis.

    Science.gov (United States)

    Niedobová, Jana; Hula, Vladimír; Michalko, Radek

    2016-06-01

    In addition to their active ingredients, pesticides contain also additives - surfactants. Use of surfactants has been increasing over the past decade, but their effects on non-target organisms, especially natural enemies of pests, have been studied only very rarely. The effect of three common agrochemical surfactants on the foraging behavior of the wolf spider Pardosa agrestis was studied in the laboratory. Differences in short-term, long-term, and overall cumulative predatory activities were investigated. We found that surfactant treatment significantly affected short-term predatory activity but had no effect on long-term predatory activity. The surfactants also significantly influenced the cumulative number of killed prey. We also found the sex-specific increase in cumulative kills after surfactants treatment. This is the first study showing that pesticide additives have a sublethal effect that can weaken the predatory activity of a potential biological control agent. More studies on the effects of surfactants are needed to understand how they affect beneficial organisms in agroecosystems.

  13. Applicability of slug interference tests under Hanford Site test conditions: Analytical assessment and field test evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Spane, F.A. Jr.

    1992-04-01

    Slug interference testing may be a useful technique for characterizing the hydraulic properties of high conductivity formations where problems associated with disposal of contaminated ground water make pumping tests undesirable. The suitability of the slug interference method for characterizing the unconfined aquifer at the Hanford Site was evaluated in a two-phase investigation. The first phase consisted of an analytical assessment. Slug interference responses were predicted over the range of conditions expected for the aquifer. The effects of partial penetration, delayed-yield and aquifer anisotropy on expected test results were also evaluated and possible analytical corrections are presented. The field test evaluation was conducted at a site with two observation wells and a stress well. Results verified the analytical evaluation and gave reasonable values of hydraulic conductivity and storativity. Test design considerations that optimize the observed response are discussed.

  14. The Slug Mucosal Irritation (SMI) assay: a tool for the evaluation of nasal discomfort.

    Science.gov (United States)

    Lenoir, Joke; Bachert, Claus; Remon, Jean-Paul; Adriaens, Els

    2013-09-01

    In this research project, the Slug Mucosal Irritation (SMI) assay was applied to predict nasal discomfort, investigating the correlation between responses in slugs and humans. Several SMI experiments and a Human Nose Irritation Test (HNIT) were performed with five NaCl solutions (0.4%, 1.3%, 2.6%, 5.4% and 10.4%) and two benzalkonium chloride solutions (BAC 0.02% and BAC 0.05%). In the HNIT, subjective evaluation of clinical discomfort was performed by 24 participants at several time points. Analyzes reveal that (1) a significant positive association existed between immediate stinging reaction reported by the participants and the mean total mucus production of the slugs (Spearman's Rank correlation=0.963, passay is a promising evaluation method for clinical nasal discomfort. Screening (prototype) formulations with this assay allows formula optimization prior to a clinical trial.

  15. Influence of process parameters on microstructure of semisolid A356 alloy slug cast through vertical pipe

    Institute of Scientific and Technical Information of China (English)

    YANG Xiao-rong; MAO Wei-min; PEI Sheng

    2008-01-01

    Suitable microstructures required for semisolid casting were formed by using a vertical pipe. Different lengths of vertical pipe, slug dimensions and pouring time were used to investigate their influence on the microstructure of A356 alloy. The results indicate that at the same length of the vertical pipe, the morphology of the primary α(Al) gradually deteriorates by the enlargement in the slug size, but the deteriorating speed slows down with increasing pipe length. They also reveal that the increase in the pipe length improves the microstructure, whereas no further improvement appears when the pipe length reaches a certain value. The optimum length of the pipe obtained in the present work is 430 mm. The microstructure of larger slug poured at higher pouring temperature gets worse and it can be improved by moderately elongating pouring time. The relative mechanisms were also discussed.

  16. Comparing functional similarity between a native and an alien slug in temperate rain forests of British Columbia

    Directory of Open Access Journals (Sweden)

    Mariano A. Rodriguez-Cabal

    2015-04-01

    Full Text Available The impacts of invasive alien species are greatest when they become dominant members of a community, introduce novel traits, and displace native species. Invasions by alien mollusks represent a novel context by which to compare trait differences between generalist native and introduced herbivores in terrestrial ecosystems. Here, we determined the abundance, habitat, feeding preferences, as well as the metabolic rate of the native Pacific banana slug (Ariolimax columbianus and the alien black slug (Arion rufus in the coastal forests of British Columbia, Canada. Through a series of observational and experimental studies, we found that alien slugs are more abundant, differ in their habitat preferences, and consumed more fungi (mushrooms than native banana slugs. Conversely, in an enclosures experiment we found that herbivory damage by native slugs was higher compared to enclosures with alien only and control enclosures. Finally, metabolic rates were similar for both slug species. These results suggest that alien black slugs possess a suite of traits that make them functionally different from native banana slugs.

  17. Control of slug damage to oilseed rape and wheat with imidacloprid seed dressings in laboratory and field experiments

    NARCIS (Netherlands)

    Simms, L.C.; Ester, A.; Wilson, M.J.

    2006-01-01

    Slugs are common pests of oilseed and cereal crops in Europe and are currently controlled using bait pellets that often fail to give adequate protection: Here we investigate the potential of the broad-spectrum insecticide imidacloprid, previously suggested to have activity against slugs, to control

  18. Three-phase slug flow in microchips can provide beneficial reaction conditions for enzyme liquid-liquid reactions.

    Science.gov (United States)

    Cech, Jiří; Přibyl, Michal; Snita, Dalimil

    2013-01-01

    Here, we introduce a solution to low stability of a two-phase slug flow with a chemical reaction occurring at the phase interface in a microfluidic reactor where substantial merging of individual reacting slugs results in the loss of uniformity of the flow. We create a three-phase slug flow by introducing a third fluid phase into the originally two-phase liquid-liquid slug flow, which generates small two-phase liquid slugs separated by gas phase. Introduction of the third phase into our system efficiently prevents merging of slugs and provides beneficial reaction conditions, such as uniform flow pattern along the whole reaction capillary, interfacial area with good reproducibility, and intensive water-oil interface renewal. We tested the three-phase flow on an enzyme hydrolysis of soybean oil and compared the reaction conversion with those from unstable two-phase slug flows. We experimentally confirmed that the three-phase slug flow arrangement provides conversions and pressure drops comparable or even better with two-phase liquid-liquid arrangements.

  19. Naturally-Forced Slug Flow Expander for Application in a Waste-Heat Recovery Cycle

    Directory of Open Access Journals (Sweden)

    Ben de Witt

    2014-11-01

    Full Text Available This paper investigates a slug-flow expander (SFE for conversion of high-pressure gas/vapor into kinetic energy of liquid slugs. The energy transfer from high-pressure to kinetic energy is quantified using thrust plate measurements. Non-dimensional thrust data is used to quantify performance by normalizing measured thrust by thrust for the same water flow rate at zero air flow rate. A total of 13 expander configurations are investigated and geometries with the shortest cavity length and the smallest exit diameter are found to result in the largest non-dimensional thrust increase. Results show that thrust augmentation increases with the initiation of slug flow in the SFE. The analysis performed on the normalized thrust readings suggested that as the water and air flow were increased to critical conditions, the liquid slugs produced by the SFE augmented the thrust measurements. The final performance evaluation was based on linear regression of the normalized thrust measurements where slug flow was generated for each SFE architecture. Greater magnitudes of the slope from the linear regression indicated the propensity of the SFE to augment thrust. This analysis confirmed that for the SFE configurations over the range of values investigated, the SFE increased thrust up to three times its original value at no air flow. Given the inherent multiphase nature of the slug-flow expander, application to systems involving expansion of wetting fluids (water as part of a waste-heat recovery system or air with water droplet formation (as part of a compressed-air energy storage system could be considered.

  20. MICROBIAL SURFACTANTS. I. GLYCOLIPIDS

    Directory of Open Access Journals (Sweden)

    Pirog T. Р.

    2014-02-01

    Full Text Available The review is devoted to surface-active glycolipids. The general characteristics, the physiological role of the rhamnolipids, trehalose lipids, sophorolipids, mannosylerythritol lipids and their traditional producers — the representatives of the genera Pseudozyma, Pseudomonas, Rhodococcus and Candida are given. The detailed analysis of the chemical structure, the stages of the biosynthesis and the regulation of some low molecular glycolipids are done. The own experimental data concerning the synthesis intensification, the physiological role and the practical use of Rhodococcus erythropolis IMV Ac-5017, Acinetobacter calcoaceticus IMV B-7241 and Nocardia vaccinii IMV B-7405 surfactants, which are a complex of the glyco-, phospho-, amino- and neutral lipids (glycolipids of all strains are presented by trehalose mycolates are summarized. It was found that R. erythropolis IMV Ac-5017, A. calcoaceticus IMV B-7241 and N. vaccinii IMV B-7405 surfactants have protective, antimicrobial and antiadhesive properties. It was shown that R. erythropolis IMV Ac-5017, A. calcoaceticus IMV B-7241 and N. vaccinii IMV B-7405 surfactants preparation of cultural liquid intensified the degradation of oil in water due to the activation of the natural petroleum-oxidizing microflora.

  1. MICROBIAL SURFACTANTS. II. LIPOPEPTIDES

    Directory of Open Access Journals (Sweden)

    T. P. Pirog

    2014-04-01

    Full Text Available The classification and the chemical structure of the lipopeptides and their producers (bacteria of the genera Bacillus and Pseudomonas are given. The role of the lipopeptides in cells motility, biofilm formation, metal binding and xenobiotics degradation and their action on the cells of pro- and eukaryotes is summarized. The stages of the nonribosomal lipopeptides synthesis and the role of two-component (GacA/GacS, ComA/ComP and the quorum system regulation of this process are shown. The potential of lactic acid bacteria and marine microorganisms as alternative surfactants producers (glycolipids, lipopeptides, phospholipids and fatty acids, glycolipopeptides are discussed. Their productivity and advantages over traditional producers are given as well. The properties of surfactants synthesized by lactic acid bacteria (the reduction of the surface tension, the critical micelle concentration, the stability in a wide range of pH, the temperature, the biological activity are summarized. Surfactants of nonpathogenic probiotic bacteria could be used as effective antimicrobial agents and antiadhesive and marine producers which able to synthesize unique metabolites that are not produced by other microorganisms.

  2. Slugging their way to immortality: driving mammary epithelial cells into a stem cell-like state.

    Science.gov (United States)

    Soady, Kelly; Smalley, Matthew J

    2012-09-10

    Delineating the molecular factors that define and maintain the mammary stem cell state is vital for understanding normal development and tumourigenesis. A recent study by Guo and colleagues identifies two master transcriptional regulators of mammary stem cells, Slug and Sox9, ectopic expression of which confers stem cell attributes on differentiated mammary epithelial cells. Slug and Sox9 expression was also shown to determine in vivo metastatic potential of human breast cancer cell lines. Understanding these factors in the context of normal lineage differentiation is an important step toward elucidating the mammary epithelial cell hierarchy and the origins of cancer stem cells.

  3. Dynamics of a two-phase flow through a minichannel: Transition from churn to slug flow

    Science.gov (United States)

    Górski, Grzegorz; Litak, Grzegorz; Mosdorf, Romuald; Rysak, Andrzej

    2016-04-01

    The churn-to-slug flow bifurcations of two-phase (air-water) flow patterns in a 2mm diameter minichannel were investigated. With increasing a water flow rate, we observed the transition of slugs to bubbles of different sizes. The process was recorded by a digital camera. The sequences of light transmission time series were recorded by a laser-phototransistor sensor, and then analyzed using the recurrence plots and recurrence quantification analysis (RQA). Due to volume dependence of bubbles velocities, we observed the formation of periodic modulations in the laser signal.

  4. Two phase flow bifurcation due to turbulence: transition from slugs to bubbles

    Science.gov (United States)

    Górski, Grzegorz; Litak, Grzegorz; Mosdorf, Romuald; Rysak, Andrzej

    2015-09-01

    The bifurcation of slugs to bubbles within two-phase flow patterns in a minichannel is analyzed. The two-phase flow (water-air) occurring in a circular horizontal minichannel with a diameter of 1 mm is examined. The sequences of light transmission time series recorded by laser-phototransistor sensor is analyzed using recurrence plots and recurrence quantification analysis. Recurrence parameters allow the two-phase flow patterns to be found. On changing the water flow rate we identified partitioning of slugs or aggregation of bubbles.

  5. Untapped therapeutic potential of surfactant proteins: is there a case for recombinant SP-D supplementation in neonatal lung disease?

    Science.gov (United States)

    Clark, Howard W

    2010-06-01

    Whilst pulmonary surfactant therapy has been highly successful in reducing mortality from respiratory distress syndrome of the newborn, a significant proportion of infants born at less than 28 weeks' gestation develop neonatal chronic lung disease. This has a complex pathogenesis but infection, inflammation, oxygen toxicity and ventilator-induced lung injury in the premature infant are all recognised risk factors for its development. Current surfactant therapies in clinical use do not contain all surfactant components and lack the hydrophilic surfactant proteins A and D. These proteins are known to have important roles in surfactant homeostasis and in protecting the lung against inflammation. This review examines the evidence from animal models supporting a role for surfactant protein-D in particular in reducing inflammation in the lung and speculates that supplementation of current surfactant therapies with recombinant forms of surfactant protein-D may help offset the risk of development of chronic lung disease.

  6. Surfactants at the Design Limit.

    Science.gov (United States)

    Czajka, Adam; Hazell, Gavin; Eastoe, Julian

    2015-08-04

    This article analyzes how the individual structural elements of surfactant molecules affect surface properties, in particular, the point of reference defined by the limiting surface tension at the aqueous cmc, γcmc. Particular emphasis is given to how the chemical nature and structure of the hydrophobic tails influence γcmc. By comparing the three different classes of surfactants, fluorocarbon, silicone, and hydrocarbon, a generalized surface packing index is introduced which is independent of the chemical nature of the surfactants. This parameter ϕcmc represents the volume fraction of surfactant chain fragments in a surface film at the aqueous cmc. It is shown that ϕcmc is a useful index for understanding the limiting surface tension of surfactants and can be useful for designing new superefficient surfactants.

  7. Pediatric tea tree oil aspiration treated with surfactant in the emergency department.

    Science.gov (United States)

    Richards, David B; Wang, George S; Buchanan, Jennie A

    2015-04-01

    Tea tree oil is an essential oil containing a mixture of aromatic hydrocarbons. We describe an 18-month-old male patient who ingested tea tree oil, developed central nervous system depression, respiratory distress, and received early emergency department treatment with surfactant. Early treatment of hydrocarbon pneumonitis with surfactant has not been previously described. Early administration of surfactant should be further evaluated for treatment of hydrocarbon aspiration.

  8. Tunable Oleo-Furan Surfactants by Acylation of Renewable Furans

    Energy Technology Data Exchange (ETDEWEB)

    Park, Dae Sung; Joseph, Kristeen E.; Koehle, Maura; Krumm, Christoph; Ren, Limin; Damen, Jonathan N.; Shete, Meera H.; Lee, Han Seung; Zuo, Xiaobing; Lee, Byeongdu; Fan, Wei; Vlachos, Dionisios G.; Lobo, Raul F.; Tsapatsis, Michael; Dauenhauer, Paul J.

    2016-11-23

    An important advance in fluid surface control was the amphiphilic surfactant comprised of coupled molecular structures (i.e. hydrophilic and hydrophobic) to reduce surface tension between two distinct fluid phases. However, implementation of simple surfactants has been hindered by the broad range of applications in water containing alkaline earth metals (i.e. hard water), which disrupt surfactant function and require extensive use of undesirable and expensive chelating additives. Here we show that sugar-derived furans can be linked with triglyceride-derived fatty acid chains via Friedel-Crafts acylation within single layer (SPP) zeolite catalysts. These alkylfuran surfactants independently suppress the effects of hard water while simultaneously permitting broad tunability of size, structure, and function, which can be optimized for superior capability for forming micelles and solubilizing in water.

  9. BINDING ISOTHERMS SURFACTANT-PROTEINS

    Directory of Open Access Journals (Sweden)

    Elena Irina Moater

    2011-12-01

    Full Text Available The interactions between surfactants and proteins shows some similarities with interactions between surfactants and polymers, but the hydrophobic amphoteric nature of proteins and their secondary and tertiary structure components make them different from conventional polymer systems. Many studies from the past about surfactant - proteins bonding used the dialysis techniques. Other techniques used to determine the binding isotherm, included ultrafiltration, ultracentrifugation, potentiometry, ion-selective electrode method and surface tension. High affinity isotherms which are typical of an anionic surfactant - protein bonding, exhibit an initial increase steep followed by a slow growth region and then a vertical growth above a certain concentration. This isotherm is typical of ionic surfactant to protein binding. Often the high affinity initial bond appears at very low concentrations of surfactant and therefore in some protein-surfactant systems, the exact shape of the isotherm in this region may be missing. The surfactant - protein binding is influenced by a number of variables such as the nature and chain length of surfactant, pH, ionic strength, temperature, nature of this protein and additives.

  10. Development of Liquid Slug Length in Gas-Liquid Slug Flow along Horizontal Pipeline: Experiment and Simulation%水平管内气液段塞流液塞长度发展规律的实验和模拟研究

    Institute of Scientific and Technical Information of China (English)

    王鑫; 郭烈锦; 张西民

    2006-01-01

    The liquid slug length distribution is crucial for designing the downstream processing system with multiphase pipeline. Experiments were conducted in a 133m long horizontal test loop. The measurements were performed by conductivity probes to determine the liquid slug length distribution. The data covered both the slug and plug flow regimes. From experimental results, the mean liquid slug lengths were relatively insensitive to gas and liquid flow rates in the higher mixture velocity range. But in the lower mixture velocity range, the mean liquid slug length decreased and then increased with mixture velocity. It shows that the development length of slug flow was longer than χ/D=1157. A slug tracking model was adapted to study the evolution of liquid slug length distribution in a horizontal pipeline. In the present model, the wake effect of elongated bubble and the pressure drop due to acceleration are taken into account and random slug lengths are introduced at the entrance. The results of the model are compared with the measured slug length distributions of slug flow regime. It shows that the predicted mean and maximum slug lengths are in agreement with the experimental data at x/D=1157 and the form of the slug length distributions is also predicted well by the model.

  11. Size separation of analytes using monomeric surfactants

    Science.gov (United States)

    Yeung, Edward S.; Wei, Wei

    2005-04-12

    A sieving medium for use in the separation of analytes in a sample containing at least one such analyte comprises a monomeric non-ionic surfactant of the of the general formula, B-A, wherein A is a hydrophilic moiety and B is a hydrophobic moiety, present in a solvent at a concentration forming a self-assembled micelle configuration under selected conditions and having an aggregation number providing an equivalent weight capable of effecting the size separation of the sample solution so as to resolve a target analyte(s) in a solution containing the same, the size separation taking place in a chromatography or electrophoresis separation system.

  12. Interaction of nonionic surfactant AEO9 with ionic surfactants

    Institute of Scientific and Technical Information of China (English)

    ZHANG Zhi-guo; YIN Hong

    2005-01-01

    The interaction in two mixtures of a nonionic surfactant AEO9 (C12H25O(CH2CH2O)9H) and different ionic surfactants was investigated. The two mixtures were AEO9/sodium dodecyl sulfate (SDS) and AEO9/cetyltrimethylammonium bromide (CTAB) at molar fraction of AEO9, αAEO9 =0.5. The surface properties of the surfactants, critical micelle concentration (CMC),effectiveness of surface tension reduction (γCMC), maximum surface excess concentration (Гmax) and minimum area per molecule at the air/solution interface (Amin) were determined for both individual surfactants and their mixtures. The significant deviations from ideal behavior (attractive interactions) of the nonionic/ionic surfactant mixtures were determined. Mixtures of both AEO9/SDS and AEO9/CTAB exhibited synergism in surface tension reduction efficiency and mixed micelle formation, but neither exhibited synergism in surface tension reduction effectiveness.

  13. Acquired phototrophy through retention of functional chloroplasts increases growth efficiency of the sea slug Elysia viridis.

    Directory of Open Access Journals (Sweden)

    Finn A Baumgartner

    Full Text Available Photosynthesis is a fundamental process sustaining heterotrophic organisms at all trophic levels. Some mixotrophs can retain functional chloroplasts from food (kleptoplasty, and it is hypothesized that carbon acquired through kleptoplasty may enhance trophic energy transfer through increased host growth efficiency. Sacoglossan sea slugs are the only known metazoans capable of kleptoplasty, but the relative fitness contributions of heterotrophy through grazing, and phototrophy via kleptoplasts, are not well understood. Fitness benefits (i.e. increased survival or growth of kleptoplasty in sacoglossans are commonly studied in ecologically unrealistic conditions under extended periods of complete darkness and/or starvation. We compared the growth efficiency of the sacoglossan Elysia viridis with access to algal diets providing kleptoplasts of differing functionality under ecologically relevant light conditions. Individuals fed Codium fragile, which provide highly functional kleptoplasts, nearly doubled their growth efficiency under high compared to low light. In contrast, individuals fed Cladophora rupestris, which provided kleptoplasts of limited functionality, showed no difference in growth efficiency between light treatments. Slugs feeding on Codium, but not on Cladophora, showed higher relative electron transport rates (rETR in high compared to low light. Furthermore, there were no differences in the consumption rates of the slugs between different light treatments, and only small differences in nutritional traits of algal diets, indicating that the increased growth efficiency of E. viridis feeding on Codium was due to retention of functional kleptoplasts. Our results show that functional kleptoplasts from Codium can provide sacoglossan sea slugs with fitness advantages through photosynthesis.

  14. Ultraviolet Radiation and the Slug Transcription Factor Induce Proinflammatory and Immunomodulatory Mediator Expression in Melanocytes

    Directory of Open Access Journals (Sweden)

    Stephanie H. Shirley

    2012-01-01

    Full Text Available Despite extensive investigation, the precise contribution of the ultraviolet radiation (UVR component of sunlight to melanoma etiology remains unclear. UVR induces keratinocytes to secrete proinflammatory and immunomodulatory mediators that promote inflammation and skin tumor development; expression of the slug transcription factor in keratinocytes is required for maximal production of these mediators. In the present studies we examined the possibility that UVR-exposed melanocytes also produce proinflammatory mediators and that Slug is important in this process. Microarray studies revealed that both UVR exposure and Slug overexpression altered transcription of a variety of proinflammatory mediators by normal human melanocytes; some of these mediators are also known to stimulate melanocyte growth and migration. There was little overlap in the spectra of cytokines produced by the two stimuli. However IL-20 was similarly induced by both stimuli and the NFκB pathway appeared to be important in both circumstances. Further exploration of UVR-induced and Slug-dependent pathways of cytokine induction in melanocytes may reveal novel targets for melanoma therapy.

  15. Toxocariasis After Slug Ingestion Characterized by Severe Neurologic, Ocular, and Pulmonary Involvement

    OpenAIRE

    Fellrath, Jean-Marc; Magnaval, Jean-François

    2014-01-01

    Human toxocariasis is generally a benign, self-curing disease, and neurologic involvement is quite exceptional. In this study, we report a case of toxocariasis caused by ingestion of an unusual transport host, namely live slugs. The clinical picture comprised eosinophilic lung involvement with severe neurologic disorders in relation to vasculitis as well as retinal detachment.

  16. Thevetia peruviana (Family: Apocynaceae in the control of slug and snail pests

    Directory of Open Access Journals (Sweden)

    A. Panigrahi

    1994-06-01

    Full Text Available An aqueous extract prepared from Kernels of the fruit of Thevetia peruviana (Pers. Schumann (Family : Apocynaceae was found under experimental conditions, to be toxic ti the slug Laevicaulis alte (Férussac and the snail Achatina fulica Bowdich, the important agrihorticultural pests of Indo-Pacific countries. Concentrations as low as 1% (w/v killed all the slugs exposed in less than 981.00 (± SD 22.76 min, and 2% of the extract killed 100% of the slugs L. alte and 50%, 50% and 30% of the snail A. fulica in between 92.34 (± SD 6.63 - 321.33 (± SD 4.14 and 271.20 (± SD 17.54 - 298.26 (± SD 16.69 min respectively. The most effective concentration of the extract was 20%; it killed 100% of exposed slugs and snails within a short time (40-50 and 90-1440 min respectively when the extract was exposed on the soil in experimental trays or when it was applied to potato slices offered as food to the gastropods.

  17. Lactic Acid Extraction and Mass Transfer Characteristics in Slug Flow Capillary Microreactors

    NARCIS (Netherlands)

    Susanti,; Winkelman, Jozef G.M.; Schuur, Boelo; Heeres, Hero J.; Yue, Jun

    2016-01-01

    Capillary microreactors operated under the slug flow regime were investigated for the separation of lactic acid from the aqueous phase using liquid–liquid reactive extraction. The experiments were performed at a 1:1 flow ratio of the aqueous to organic phases in a setup consisting of an inlet Y-type

  18. Recreating Riser Slugging Flow Based on an Economic Lab-sized Setup

    DEFF Research Database (Denmark)

    Hansen, Lasse; Pedersen, Simon; Yang, Zhenyu;

    2013-01-01

    As a kind of periodic phenomenon, the slugging flow in the offshore oil & gas production addresses a lot of attentions, due to its limitation of production rate, periodic overload processing facilities, and even direct cause of emergent shutdown. This work studies the emulation of the riser...

  19. Mass transfer coefficient of slug flow for organic solvent-aqueous system in a microreactor

    Energy Technology Data Exchange (ETDEWEB)

    Tuek, Ana Jurinjak; Anic, Iva; Kurtanjek, Zelimir; Zelic, Bruno [University of Zagreb, Zagreb (Croatia)

    2015-06-15

    Application of microreactor systems could be the next break-through in the intensification of chemical and biochemical processes. The common flow regime for organic solvent-aqueous phase two-phase systems is a segmented flow. Internal circulations in segments cause high mass transfer and conversion. We analyzed slug flow in seven systems of organic solvents and aqueous phase. To analyze how slug lengths in tested systems depend on linear velocity and physical and chemical properties of used organic solvents, regression models were proposed. It was shown that models based on linearization of approximation by potentials give low correlation for slug length prediction; however, application of an essential nonlinear model of multiple layer perception (MLP) neural network gives high correlation with R{sup 2}=0.9. General sensitivity analysis was applied for the MLP neural network model, which showed that 80% of variance in slug length for the both phases is accounted for the viscosity and density of the organic phases; 10% is accounted by surface tension of the organic phase, while molecular masses and flow rates each account for 5%. For defined geometry of microreactor, mass transfer has been determined by carrying out the neutralization experiment with NaOH where acetic acid diffuses from organic phase (hexane) into aqueous phase. Estimated mass transfer coefficients were in the range k{sub L}a=4,652-1,9807 h{sup -1}.

  20. Transient drift flux modelling of severe slugging in pipeline-riser systems

    NARCIS (Netherlands)

    Malekzadeh, R.; Belfroid, S.P.C.; Mudde, R.F.

    2012-01-01

    A large number of pipelines in the petroleum industry simultaneously transport gas and liquid. Transient behaviour of multiphase flow is frequently encountered in these pipelines. A common example is severe slugging that can occur in multiphase flow systems where a pipeline segment with a downward o

  1. The cultivation of Anabaena variabilis in a bubble column operating under bubbly and slug flows.

    Science.gov (United States)

    Yoon, Jong Hyun; Choi, Shin Sik; Park, Tai Hyun

    2012-04-01

    In a bubble column reactor with an inner diameter of 6cm and a height of 63cm for the culture of cyanobacteria two different shapes of bubbles can be generated, resulting in bubbly flow or slug flow. Growth of Anabaena variabilis under slug flow (1.9g/l/day) was 1.73 times higher than that under bubbly flow (1.1g/l/day) when the specific irradiation rate was maintained above 10μmol/s/g dry cell. Although a stepwise increase in superficial gas velocity enhanced the average cell growth rate under bubbly flow by 1.57 times, the average cell growth rate during the deceleration phase under bubbly flow (1.98g/l/day) was 0.61 times smaller than that under slug flow (3.22g/l/day). These results demonstrate that the bubble shape in the slug flow was advantageous in regards to the radial circulation of cells.

  2. Electrophoretic separations in poly(dimethylsiloxane) microchips using mixtures of ionic, nonionic and zwitterionic surfactants.

    Science.gov (United States)

    Guan, Qian; Noblitt, Scott D; Henry, Charles S

    2012-09-01

    The use of surfactant mixtures to affect both EOF and separation selectivity in electrophoresis with PDMS substrates is reported, and capacitively coupled contactless conductivity detection is introduced for EOF measurement on PDMS microchips. First, the EOF was measured for two nonionic surfactants (Tween 20 and Triton X-100), mixed ionic/nonionic surfactant systems (SDS/Tween 20 and SDS/Triton X-100), and finally for the first time, mixed zwitterionic/nonionic surfactant systems (TDAPS/Tween 20 and TDAPS/Triton X-100). EOF for the nonionic surfactants decreased with increasing surfactant concentration. The addition of SDS or TDAPS to a nonionic surfactant increased EOF. After establishing the EOF behavior, the separation of model catecholamines was explored to show the impact on separations. Similar analyte resolution with greater peak heights was achieved with mixed surfactant systems containing Tween 20 and TDAPS relative to the single surfactant system. Finally, the detection of catecholamine release from PC12 cells by stimulation with 80 mM K(+) was performed to demonstrate the usefulness of mixed surfactant systems to provide resolution of biological compounds in complex samples.

  3. Electrophoretic separations in poly(dimethylsiloxane) microchips using a mixture of ionic and zwitterionic surfactants.

    Science.gov (United States)

    Guan, Qian; Noblitt, Scott D; Henry, Charles S

    2012-01-01

    The use of mixtures of ionic and zwitterionic surfactants in poly(dimethylsiloxane) (PDMS) microchips is reported. The effect of surfactant concentration on electroosmotic flow (EOF) was studied for a single anionic surfactant (sodium dodecyl sulfate, SDS), a single zwitterionic surfactant (N-tetradecylammonium-N,N-dimethyl-3-ammonio-1-propanesulfonate, TDAPS), and a mixed SDS/TDAPS surfactant system. SDS increased the EOF as reported previously while TDAPS showed an initial increase in EOF followed by a reduction at higher concentrations. When TDAPS was added to a solution containing SDS, the EOF decreased in a concentration-dependent manner. The EOF for all three surfactant systems followed expected pH trends, with increasing EOF at higher pH. The mixed surfactant system allowed tuning of the EOF across a range of pH and concentration conditions. After establishing the EOF behavior, the adsorption/desorption kinetics were measured and showed a slower adsorption/desorption rate for TDAPS than SDS. Finally, the separation and electrochemical detection of model catecholamines in buffer and reduced glutathione in red blood cell lysate using the mixed surfactant system were explored. The mixed surfactant system provided shorter analysis times and/or improved resolution when compared to the single surfactant systems.

  4. ADSORPTION OF SURFACTANT ON CLAYS

    Science.gov (United States)

    Surfactants used to enhance remediation of soils by soil washing are often lost in the process. Neither the amount nor the cause of this loss is known. It is assumed that clays present in the soil are responsible for the loss of the surfactant. In this papere, adsorption prope...

  5. Surfactant monitoring by foam generation

    Science.gov (United States)

    Mullen, Ken I.

    1997-01-01

    A device for monitoring the presence or absence of active surfactant or other surface active agents in a solution or flowing stream based on the formation of foam or bubbles is presented. The device detects the formation of foam with a light beam or conductivity measurement. The height or density of the foam can be correlated to the concentration of the active surfactant present.

  6. Surfactant adsorption kinetics in microfluidics

    Science.gov (United States)

    Riechers, Birte; Maes, Florine; Akoury, Elias; Semin, Benoît; Gruner, Philipp; Baret, Jean-Christophe

    2016-10-01

    Emulsions are metastable dispersions. Their lifetimes are directly related to the dynamics of surfactants. We design a microfluidic method to measure the kinetics of adsorption of surfactants to the droplet interface, a key process involved in foaming, emulsification, and droplet coarsening. The method is based on the pH decay in the droplet as a direct measurement of the adsorption of a carboxylic acid surfactant to the interface. From the kinetic measurement of the bulk equilibration of the pH, we fully determine the adsorption process of the surfactant. The small droplet size and the convection during the droplet flow ensure that the transport of surfactant through the bulk is not limiting the kinetics of adsorption. To validate our measurements, we show that the adsorption process determines the timescale required to stabilize droplets against coalescence, and we show that the interface should be covered at more than 90% to prevent coalescence. We therefore quantitatively link the process of adsorption/desorption, the stabilization of emulsions, and the kinetics of solute partitioning—here through ion exchange—unraveling the timescales governing these processes. Our method can be further generalized to other surfactants, including nonionic surfactants, by making use of fluorophore-surfactant interactions.

  7. Gas6 induces cancer cell migration and epithelial–mesenchymal transition through upregulation of MAPK and Slug

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Yunhee [Department of Chemistry, Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of); Immunotherapy Research Center, Korea Research Institute of Bioscience and Biotechnology, Daejeon (Korea, Republic of); Lee, Mira [Immunotherapy Research Center, Korea Research Institute of Bioscience and Biotechnology, Daejeon (Korea, Republic of); Kim, Semi, E-mail: semikim@kribb.re.kr [Department of Chemistry, Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of); Immunotherapy Research Center, Korea Research Institute of Bioscience and Biotechnology, Daejeon (Korea, Republic of)

    2013-04-26

    Highlights: •We investigated the molecular mechanisms underlying Gas6-mediated cancer cell migration. •Gas6 treatment and subsequent Axl activation induce cell migration and EMT via upregulation of Slug. •Slug expression mediated by Gas6 is mainly through c-Jun and ATF-2 in an ERK1/2 and JNK-dependent manner. •The Gas6/Axl-Slug axis may be exploited as a target for anti-cancer metastasis therapy. -- Abstract: Binding of Gas6 to Axl (Gas6/Axl axis) alters cellular functions, including migration, invasion, proliferation, and survival. However, the molecular mechanisms underlying Gas6-mediated cell migration remain poorly understood. In this study, we found that Gas6 induced the activation of JNK and ERK1/2 signaling in cancer cells expressing Axl, resulting in the phosphorylation of activator protein-1 (AP-1) transcription factors c-Jun and ATF-2, and induction of Slug. Depletion of c-Jun or ATF-2 by siRNA attenuated the Gas6-induced expression of Slug. Slug expression was required for cell migration and E-cadherin reduction/vimentin induction induced by Gas6. These results suggest that Gas6 induced cell migration via Slug upregulation in JNK- and ERK1/2-dependent mechanisms. These data provide an important insight into the molecular mechanisms mediating Gas6-induced cell migration.

  8. A PLIC-VOF-Based Simulation of Water-Organic Slug Flow Characteristics in a T-Shaped Microchannel

    Directory of Open Access Journals (Sweden)

    Xian Wang

    2013-01-01

    Full Text Available A water-organic slug flow in a T-shaped microchannel was numerically studied due to its importance in the microreactor system. Various factors affecting the flow mode were studied, for example, channel width, fluid viscosity, interfacial tension, and inlet velocity. The volume of fluid (VOF method was used to track the liquid-liquid interface, and the piecewise-liner interface construction (PLIC technique was adopted to get a sharp interface. The interfacial tension was simulated with continuum surface force (CSF, model and the wall adhesion boundary condition was taken into consideration. The results show that strong vortexes appear in both phases at the meeting sites of main and lateral channels where an organic slug is producing. Inlet velocity influences the slug length and flow mode greatly. The ratio between the slug lengths of two phases in the main channel is almost equal to the ratio between their inlet velocities. If the slug is produced, the interfacial tension and organic viscosity have less effect on the slug length for 200 μm microchannel. The slug producing rate is much higher in a narrow channel than that in a wide channel.

  9. Magnetic surfactants as molecular based-magnets with spin glass-like properties.

    Science.gov (United States)

    Brown, Paul; Smith, Gregory N; Hernández, Eduardo Padrón; James, Craig; Eastoe, Julian; Nunes, Wallace C; Settens, Charles M; Hatton, T Alan; Baker, Peter J

    2016-05-05

    This paper reports the use of muon spin relaxation spectroscopy to study how the aggregation behavior of magnetic surfactants containing lanthanide counterions may be exploited to create spin glass-like materials. Surfactants provide a unique approach to building in randomness, frustration and competing interactions into magnetic materials without requiring a lattice of ordered magnetic species or intervening ligands and elements. We demonstrate that this magnetic behavior may also be manipulated via formation of micelles rather than simple dilution, as well as via design of surfactant molecular architecture. This somewhat unexpected result indicates the potential of using novel magnetic surfactants for the generation and tuning of molecular magnets.

  10. Application of Ceramic Bond Coating for Reusable Melting Crucible of Metallic Fuel Slugs

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Ki-Hwan; Song, Hoon; Ko, Young-Mo; Park, Jeong-Yong; Lee, Chan-Bock [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Hong, Ki-Won [Chungnam National University, Daejeon (Korea, Republic of)

    2016-10-15

    Metal fuel slugs of the driver fuel assembly have been fabricated by injection casting of the fuel alloys under a vacuum state or an inert atmosphere. Traditionally, metal fuel such as a U-Zr alloy system for SFR has been melted in slurry-coated graphite crucibles and cast in slurry-coated quartz tube molds to prevent melt/material interactions. Reactive coatings and porous coatings can be a source of melt contaminations, and fuel losses, respectively. Ceramic Y{sub 2}O{sub 3}, TiC, and TaC coating materials showed no penetration in the protective layer after a melt dipping test. However, the ceramic coating materials showed separations in the coating interface between the substrate and coating layer, or between the coating layer and fuel melt after the dipping test. All plasma-spray coated methods maintained a sound coating state after a dipping test with U-10wt.%Zr melt. A single coating Y{sub 2}O{sub 3}(150) layer and double coating layer of TaC(50)-Y{sub 2}O{sub 3}(100), showed a sound state or little penetration in the protective layer after a dipping test with U-10wt.%Zr-5wt.%RE melt. Injection casting experiments of U-10wt.%Zr and U-10wt.%Zr-5wt.%RE fuel slugs have been performed to investigate the feasibility of a reusable crucible of the metal fuel slugs. U–10wt.%Zr and U–10wt.%Zr–5wt.%RE fuel slugs have been soundly fabricated without significant interactions of the graphite crucibles. Thus, the ceramic plasma-spray coatings are thought to be promising candidate coating methods for a reusable graphite crucible to fabricate metal fuel slugs.

  11. Numerical investigation of temporal changes in volcanic deformation caused by a gas slug ascent in the conduit

    Science.gov (United States)

    Kawaguchi, Ryohei; Nishimura, Takeshi

    2015-09-01

    Strombolian type eruptions are considered to be generated by a sudden release of a large gas slug that migrates upward in the conduit filled with a low viscous basaltic magma. We examine volcano deformations caused by such a gas slug to understand the Strombolian eruption mechanism from geodetic observation data. We model spatio-temporal pressure changes in the conduit by using a gas slug ascent model presented by James et al. (2008). As a gas slug ascends in the conduit, its volume expands because of depressurization. Hence, the magma head lifts up in the conduit and the upper part of the conduit wall is stressed. In the conduit, magma pressure increases with depth according to the bulk density of magma: the gas slug part with a low density is characterized by a small pressure gradient, while the other parts, consisting of melt, are characterized by a large pressure gradient. We numerically calculate volcano deformations caused by the spatio-temporal changes of magma pressure predicted from the basic equations representing gas slug locations in the conduit. Simulation results show that the radial and vertical displacements and tilt changes indicate volcano deformations that represent the inflation originating from the stress increase at the upper part of conduit. As the gas slug reaches the shallow part of conduit, the rate of inflation observed in the radial displacement decreases, the vertical displacement starts to move downward, and the tilt turns to show down toward the crater. These deflation signals are caused by a moving deflation source in the conduit that is formed beneath the gas slug. Since these predicted features are not observed in the tilt records associated with explosions at Stromboli volcano (Genco and Ripepe, 2010), it is necessary to modify the gas slug ascent model or to introduce other mechanisms to better understand the magma dynamics of Strombolian eruption.

  12. Correlation between Slug transcription factor and miR-221 in MDA-MB-231 breast cancer cells

    Directory of Open Access Journals (Sweden)

    Lambertini Elisabetta

    2012-10-01

    Full Text Available Abstract Background Breast cancer and its metastatic progression is mainly directed by epithelial to mesenchymal transition (EMT, a phenomenon supported by specific transcription factors and miRNAs. Methods In order to investigate a possible correlation between Slug transcription factor and miR-221, we performed Slug gene silencing in MDA-MB-231 breast cancer cells and evaluated the expression of genes involved in supporting the breast cancer phenotype, using qRT-PCR and Western blot analysis. Chromatin immunoprecipitation and wound healing assays were employed to determine a functional link between these two molecules. Results We showed that Slug silencing significantly decreased the level of miR-221 and vimentin, reactivated Estrogen Receptor α and increased E-cadherin and TRPS1 expression. We demonstrated that miR-221 is a Slug target gene, and identified a specific region of miR-221 promoter that is transcriptionally active and binds the transcription factor Slug “in vivo”. In addition, we showed that in Slug-silenced cells, wich retained residual miR-221 (about 38%, cell migration was strongly inhibited. Cell migration was inhibited, but to a less degree, following complete knockdown of miR-221 expression by transfection with antagomiR-221. Conclusions We report for the first time evidence of a correlation between Slug transcription factor and miR-221 in breast cancer cells. These studies suggest that miR-221 expression is, in part, dependent on Slug in breast cancer cells, and that Slug plays a more important role than miR-221 in cell migration and invasion.

  13. Physicochemical treatments of anionic surfactants wastewater: Effect on aerobic biodegradability.

    Science.gov (United States)

    Aloui, Fathi; Kchaou, Sonia; Sayadi, Sami

    2009-05-15

    The effect of different physicochemical treatments on the aerobic biodegradability of an industrial wastewater resulting from a cosmetic industry has been investigated. This industrial wastewater contains 11423 and 3148mgL(-1) of chemical oxygen demand (COD) and anionic surfactants, respectively. The concentration of COD and anionic surfactants were followed throughout the diverse physicochemical treatments and biodegradation experiments. Different pretreatments of this industrial wastewater using chemical flocculation process with lime and aluminium sulphate (alum), and also advanced oxidation process (electro-coagulation (Fe and Al) and electro-Fenton) led to important COD and anionic surfactants removals. The best results were obtained using electro-Fenton process, exceeding 98 and 80% of anionic surfactants and COD removals, respectively. The biological treatment by an isolated strain Citrobacter braakii of the surfactant wastewater, as well as the pretreated wastewater by the various physicochemical processes used in this study showed that the best results were obtained with electro-Fenton pretreated wastewater. The characterization of the treated surfactant wastewater by the integrated process (electro-coagulation or electro-Fenton)-biological showed that it respects Tunisian discharge standards.

  14. INFLUENCE OF SURFACTANT ON TWO-PHASE FLOW REGIME AND PRESSURE DROP IN UPWARD INCLINED PIPES

    Institute of Scientific and Technical Information of China (English)

    XIA Guo-dong; CHAI Lei

    2012-01-01

    The influence of a surfactant on the two-phase flow regime and the pressure drop in upward inclined pipes is investigated for various gas/liquid flow rates.The air/water and air/100 ppm sodium dodecyl sulphate aqueous solution are used as the working fluids.The influence of the surfactant on the two-phase flow regime in upward inclined pipes is investigated using the electrical tomographic technique.For 0°,2.5° and 5° pipe inclinations,the surfactant has obvious effect on the transition from the stratified wavy flow to the annular flow,and the range of the stratified smooth flow regime is also extended to higher gas velocities.For 10°pipe inclination,no stratified flow regime is observed in the air/water flow.In the air/surfactant solution system,however,the stratified flow regime can be found in the range of USG =10m/s-28m/s and USL =0.07 m/s-0.2 m/s.For all inclination angles,the changes of the pressure gradient characteristics are accompanied with the flow pattern transitions.Adding surfactant in a two-phase flow would reduce the pressure gradient significantly in the slug flow and annular flow regimes.In the annular flow regime,the pressure gradient gradually becomes free of the influence of the upward inclined angle,and is only dependent on the property of the two-phase flow.

  15. Learning control for riser-slug elimination and production-rate optimization for an offshore oil and gas production process

    DEFF Research Database (Denmark)

    Pedersen, Simon; Løhndorf, Petar Durdevic; Yang, Zhenyu

    2014-01-01

    Slugging flow in the offshore oil & gas production attracts lot of attention due to it's limitation of production rate, periodic overload on processing facilities, and even direct cause of emergency shutdown. This work aims at two correlated objectives: (i) Preventing slugging flow; and meanwhile......, (ii) maximizing the production rate at the riser of an offshore production platform, by manipulating a topside choke valve through a learning switching model-free PID controller. The results show good steady-state performance, though a long settling time due to the unknown reference for no slugging...

  16. Innovation in surfactant therapy II: surfactant administration by aerosolization.

    Science.gov (United States)

    Pillow, J Jane; Minocchieri, S

    2012-01-01

    Instilled bolus surfactant is the only approved surfactant treatment for neonatal respiratory distress syndrome. However, recent trends towards increased utilization of noninvasive respiratory support for preterm infants with surfactant deficiency have created a demand for a similarly noninvasive means of administering exogenous surfactant. Past approaches to surfactant nebulization met with varying success due to inefficient aerosol devices resulting in low intrapulmonary delivery doses of surfactant with variable clinical effectiveness. The recent development of vibrating membrane nebulizers, coupled with appropriate positioning of the interface device, indicates that efficient delivery of aerosolized surfactant is now a realistic goal in infants. Evidence of clinical effect despite low total administered dose in pilot studies, together with suggestions of enhanced homogeneity of pulmonary distribution indicate that this therapy may be applied in a cost-effective manner, with minimal patient handling and disruption. These studies need to be subjected to appropriately designed randomized controlled trials. Further work is also required to determine the optimum delivery route (mask, intranasal prong, nasopharyngeal or laryngeal), dosing amount and redosing interval.

  17. Impact of Surfactant Type on Adsorption Process and Oil Recovery: Implementation of New Surfactant Produced from Zizyphus Spina-Christi Extract

    National Research Council Canada - National Science Library

    Zargartalebi, Mohammad; Barati, Nasim; Pordel Shahri, Mojtaba

    2014-01-01

    Three different types of surfactants containing an anionic, a cationic and a new nonionic biosurfactant, Zizyphus Spina-Christi extract were used for the purpose of oil recovery in a core flood system...

  18. Therapeutic surfactant-stripped frozen micelles

    Science.gov (United States)

    Zhang, Yumiao; Song, Wentao; Geng, Jumin; Chitgupi, Upendra; Unsal, Hande; Federizon, Jasmin; Rzayev, Javid; Sukumaran, Dinesh K.; Alexandridis, Paschalis; Lovell, Jonathan F.

    2016-05-01

    Injectable hydrophobic drugs are typically dissolved in surfactants and non-aqueous solvents which can induce negative side-effects. Alternatives like `top-down' fine milling of excipient-free injectable drug suspensions are not yet clinically viable and `bottom-up' self-assembled delivery systems usually substitute one solubilizing excipient for another, bringing new issues to consider. Here, we show that Pluronic (Poloxamer) block copolymers are amenable to low-temperature processing to strip away all free and loosely bound surfactant, leaving behind concentrated, kinetically frozen drug micelles containing minimal solubilizing excipient. This approach was validated for phylloquinone, cyclosporine, testosterone undecanoate, cabazitaxel and seven other bioactive molecules, achieving sizes between 45 and 160 nm and drug to solubilizer molar ratios 2-3 orders of magnitude higher than current formulations. Hypertonic saline or co-loaded cargo was found to prevent aggregation in some cases. Use of surfactant-stripped micelles avoided potential risks associated with other injectable formulations. Mechanistic insights are elucidated and therapeutic dose responses are demonstrated.

  19. Interaction of nonionic surfactant AEO9 with ionic surfactants*

    OpenAIRE

    2005-01-01

    The interaction in two mixtures of a nonionic surfactant AEO9 (C12H25O(CH2CH2O)9H) and different ionic surfactants was investigated. The two mixtures were AEO9/sodium dodecyl sulfate (SDS) and AEO9/cetyltrimethylammonium bromide (CTAB) at molar fraction of AEO9, α AEO9=0.5. The surface properties of the surfactants, critical micelle concentration (CMC), effectiveness of surface tension reduction (γ CMC), maximum surface excess concentration (Γ max) and minimum area per...

  20. Synthesis and surface activity of diether-linked phosphoglycerols: potential applications for exogenous lung surfactants.

    Science.gov (United States)

    Notter, Robert H; Wang, Zhongyi; Wang, Zhengdong; Davy, Jason A; Schwan, Adrian L

    2007-01-01

    The synthesis of three phosphoglycerols is described, one of which contains the previously unknown phosphonoglycerol headgroup. The surface tension-lowering capabilities of synthetic lung surfactant mixtures containing the PG analogs were measured on the pulsating bubble surfactometer and compared to known controls. The PG-containing mixtures exhibited superior surface tension-lowering properties indicating the significant potential of these analogs as components in synthetic exogenous lung surfactants.

  1. Polyelectrolyte surfactant aggregates and their deposition on macroscopic surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Voisin, David

    2002-07-01

    Oppositely charged surfactant and polyelectrolyte are present in hair shampoos and conditioners, together with particles (e.g. anti-dandruff agents for scalp) and droplets (e.g. silicone oil for the hair). These are normally formulated at high surfactant concentrations, beyond the flocculation region for the polyelectrolyte concentration used. However, on dilution with water, during application, flocs are formed which carry the particles and droplets to the scalp and hair. The addition of an anionic surfactant to an aqueous solution of cationic polyelectrolyte, at a given concentration, can lead to the formation of polyelectrolyte-surfactant 'particles', in which the surfactant 'binds' to the polyelectrolyte. This occurs from the critical association concentration (CAC), up to the surfactant concentration corresponding to maximum binding. Within this range of surfactant concentrations, the surfactant bound to the polyelectrolyte is thought to associate to form what might be termed 'internal micelles'. Each polyelectrolyte-surfactant particle in the region of the CAC, and just beyond, contains many polyelectrolyte chains, held together essentially by micelle bridges. These particles, however, remain net positively charged, and therefore stable. At the other end of the binding range of the surfactant, so many internal micelles are present that the polymer-surfactant particles are now net negatively charged. Indeed binding stops since no further micelles can be accommodated. Again, the particles are stable. However, there exists a range of surfactant concentrations, lying within the range referred to above, where the net charge is reduced sufficiently that the polymer-surfactant particles will flocculate to form much larger structures. The onset of this second range might be termed the 'critical flocculation concentration' (CFC), and the end, the 'critical stabilisation concentration' (CSC). In this work, the CFC and

  2. Surfactant enhanced volumetric sweep efficiency

    Energy Technology Data Exchange (ETDEWEB)

    Harwell, J.H.; Scamehorn, J.F.

    1989-10-01

    Surfactant-enhanced waterflooding is a novel EOR method aimed to improve the volumetric sweep efficiencies in reservoirs. The technique depends upon the ability to induce phase changes in surfactant solutions by mixing with surfactants of opposite charge or with salts of appropriate type. One surfactant or salt solution is injected into the reservoir. It is followed later by injection of another surfactant or salt solution. The sequence of injections is arranged so that the two solutions do not mix until they are into the permeable regions well away from the well bore. When they mix at this point, by design they form a precipitate or gel-like coacervate phase, plugging this permeable region, forcing flow through less permeable regions of the reservoir, improving sweep efficiency. The selectivity of the plugging process is demonstrated by achieving permeability reductions in the high permeable regions of Berea sandstone cores. Strategies were set to obtain a better control over the plug placement and the stability of plugs. A numerical simulator has been developed to investigate the potential increases in oil production of model systems. Furthermore, the hardness tolerance of anionic surfactant solutions is shown to be enhanced by addition of monovalent electrolyte or nonionic surfactants. 34 refs., 32 figs., 8 tabs.

  3. MICROBIAL SURFACTANTS IN ENVIRONMENTAL TECHNOLOGIES

    Directory of Open Access Journals (Sweden)

    T. P. Pirog

    2015-08-01

    Full Text Available It was shown literature and own experimental data concerning the use of microbial surface active glycolipids (rhamno-, sophoro- and trehalose lipids and lipopeptides for water and soil purification from oil and other hydrocarbons, removing toxic heavy metals (Cu2+, Cd2+, Ni2+, Pb2+, degradation of complex pollution (oil and other hydrocarbons with heavy metals, and the role of microbial surfactants in phytoremediation processes. The factors that limit the use of microbial surfactants in environmental technologies are discussed. Thus, at certain concentrations biosurfactant can exhibit antimicrobial properties and inhibit microorganisms destructing xenobiotics. Microbial biodegradability of surfactants may also reduce the effectiveness of bioremediation. Development of effective technologies using microbial surfactants should include the following steps: monitoring of contaminated sites to determine the nature of pollution and analysis of the autochthonous microbiota; determining the mode of surfactant introduction (exogenous addition of stimulation of surfactant synthesis by autochthonous microbiota; establishing an optimal concentration of surfactant to prevent exhibition of antimicrobial properties and rapid biodegradation; research both in laboratory and field conditions.

  4. Decoupling of dynamic processes in surfactant-based liquid mixtures: the case of lithium-containing bis(2-ethylhexyl)phosphoric acid/bis(2-ethylhexyl)amine systems.

    Science.gov (United States)

    Nicotera, Isabella; Oliviero Rossi, Cesare; Turco Liveri, Vincenzo; Calandra, Pietro

    2014-07-22

    Pure surfactant liquids and their binary mixtures, because of the amphiphilic nature of the molecules involved, can exhibit nanosegregation and peculiar transport properties. The idea that inspired this work is that the possibility of including in such media salts currently used for technological applications should lead to a synergy between the properties of the salt and those of the medium. Therefore, the dynamic features of bis(2-ethylhexyl)amine (BEEA) and bis(2-ethylhexyl)phosphoric acid (HDEHP) liquid mixtures were investigated as a function of composition and temperature by (1)H nuclear magnetic resonance (NMR) spectroscopy and rheometry. Inclusion of litium trifluoromethanesulfonate (LiT) has been investigated by infrared spectroscopy, pulsed field gradient NMR, and conductimetry methods to highlight the solubilizing and confining properties of these mixtures as well as the lithium conductivity. It was found that BEEA/HDEHP binary liquid mixtures show zero-threshold percolating self-assembly with a maximum in viscosity and a minimum in molecular diffusion at a 1:1 composition. Dissolution of LiT in such system can occur via confinement in the locally self-assembled polar domains. Despite this confinement, Li(+) conduction is scarcely dependent on the medium composition because of the possibility of a field-induced hopping decoupled by the structural and dynamical features of the medium.

  5. Electrokinetic investigation of surfactant adsorption.

    Science.gov (United States)

    Bellmann, C; Synytska, A; Caspari, A; Drechsler, A; Grundke, K

    2007-05-15

    Fuerstenau [D.W. Fuerstenau, in: M.L. Hair (Ed.), Dekker, New York, 1971, p. 143] has already discussed the role of hydrocarbon chain of surfactants, the effect of alkyl chain length, chain structure and the pH of the solution on the adsorption process of surfactants. Later Kosmulski [M. Kosmulski, Chemical Properties of Material Surfaces, Surfactant Science Series, vol. 102, Dekker, New York, Basel, 2001] included the effect of surfactant concentration, equilibration time, temperature and electrolyte in his approaches. Certainly, the character of the head groups of the surfactant and the properties of the adsorbent surface are the basis for the adsorption process. Different surfactants and adsorbents cause different adsorption mechanisms described firstly by Rosen [M.J. Rosen, Surfactants and Interfacial Phenomena, second ed., Wiley, New York, 1989]. These adsorption mechanisms and their influencing factors were studied by electrokinetic investigations. Here only changes of the charges at the surfaces could be detected. To control the results of electrokinetic investigations they were compared with results from ellipsometric measurements. In the case of surfactant adsorption the chain length was vitally important. It could be shown by the adsorption of alkyl trimethyl ammonium bromides onto polymer films spin coated at wafer surfaces. The influence of the chain length depending on surface properties of the polymer film was studied. Streaming potential measurements were applied for these investigations. The obtained results enabled us to calculate the molar cohesive free energy per mol of CH2-group in the alkaline chain of the surfactant if all other specific adsorption effects were neglected.

  6. 疏水缔合型PDMC净水剂的合成及其对AS废水处理的研究%STUDY ON SYNTHESIS OF HYDROHOBICALLY ASSOCIATING CATIONIC PDMC WATER PURIFYING REAGENT AND ITS TREATMENT OF ANIONIC SURFACTANT-CONTAINING WASTEWATER

    Institute of Scientific and Technical Information of China (English)

    王瑞; 陈均志

    2011-01-01

    Hydrohobically associating cationic PDMC water purifying reagent was prepared at 80 ℃ by copolymerization using laurylacrylate ester(LA) and methacryloyloxyethyl trimethyl ammonium chloride (DMC) in the presence of alcohol as sol vent, hexadecyl trimethyl ammonium Bromide(CTAB) as Phase transfer catalyst and benzoyl peroxide(BPO) as initiator, the copolymer was purified and characterized by IR spectral. Water solubility, intrinsic viscosity and the efficiency of treatment of anionic-surfactant(AS) containing wastewater were studied based on the copolymer composition. The results showed that with the increase of hydrophobic parts,the copolymer's water-solublity decreased and intrinsic viscosity begin increased and then decreased. The efficiency was better when the mole rate of DMC and LA is 8:2. Compared with a variety of cationic flocculant, the synthesized copolymer has better effect treating the anionic surfactant-containing wastewater.%以无水乙醇为溶剂,CTAB为相转移催化剂,在80℃下用引发剂BPO将LA与DMC共聚,合成了疏水缔合型阳离子净水剂,提纯后对聚合物进行红外光谱表征.讨论了共聚组成对水溶性、特性粘数、处理阴离子表面活性剂(AS)废水能力的影响.结果表明,随着疏水成分增加水溶性减小,特性粘数先增加后减小,当n(DMC)∶ n(LA)为8:2时,处理废水效果最佳;同时与多种阳离子絮凝剂比较,该产品处理阴离子废水效果更佳.

  7. Toward A 3-D Picture of Hydraulic Conductivity With Multilevel Slug Tests

    Science.gov (United States)

    McElwee, C. D.; McElwee, C. D.; Ross, H. C.

    2001-12-01

    The GEMS (Geohydrologic Experiment and Monitoring Site) field area has been established (in the Kansas River valley near Lawrence, Kansas) for a variety of reasons relating to research and teaching in hydrogeology at the University of Kansas. Over 70 wells have been installed for various purposes. The site overlies an alluvial aquifer with a total thickness of about 70 feet. The water table is typically about 20 feet below the surface, giving a total saturated thickness of about 50 feet. The upper part of the aquifer is finer material consisting of silt and clay. Typically, the lower 35 feet of the aquifer is sand and gravel. A number of wells through out the site are fully screened through the sand and gravel aquifer. Some of these fully screened wells are larger diameters; however, most wells are constructed of 2 inch PVC casing. Slug tests are widely used in hydrogeology to measure hydraulic conductivity. Over the last several years we have been conducting research to improve the slug test method. We have previously reported the detailed structure of hydraulic conductivity that can be seen in a 5 inch well (McElwee and Zemansky, EOS, v. 80, no. 46, p. F397, 1999) at this site, using multilevel slug tests. The existing 2 inch, fully screened wells are spread out over the site and offer the opportunity for developing a 3-D picture of the hydraulic conductivity distribution. However, it is difficult to develop a system that allows multilevel slug tests to be done accurately and efficiently in a 2 inch well. This is especially true in regions of very high hydraulic conductivity, where the water velocity in the casing will be relatively high. The resistance caused by frictional forces in the equipment must be minimized and a model taking account of these forces must be used. We have developed a system (equipment, software, and technique) for performing multilevel slug tests in 2 inch wells. Some equipment configurations work better than others. The data that we have

  8. Anaerobic Biodegradation of Detergent Surfactants

    Directory of Open Access Journals (Sweden)

    Erich Jelen

    2009-03-01

    Full Text Available Detergent surfactantscan be found in wastewater in relevant concentrations. Most of them are known as ready degradable under aerobic conditions, as required by European legislation. Far fewer surfactants have been tested so far for biodegradability under anaerobic conditions. The natural environment is predominantly aerobic, but there are some environmental compartments such as river sediments, sub-surface soil layer and anaerobic sludge digesters of wastewater treatment plants which have strictly anaerobic conditions. This review gives an overview on anaerobic biodegradation processes, the methods for testing anaerobic biodegradability, and the anaerobic biodegradability of different detergent surfactant types (anionic, nonionic, cationic, amphoteric surfactants.

  9. A mini slug test method for determination of a local hydraulic conductivity of an unconfined sandy aquifer

    DEFF Research Database (Denmark)

    Hinsby, Klaus; Bjerg, Poul Løgstrup; Andersen, Lars J.;

    1992-01-01

    from level to level and thereby establish vertical profiles of the hydraulic conductivity. The head data from the test well are recorded with a 10 mm pressure transducer, and the initial head difference required is established by a small vacuum pump. The method described has provided 274 spatially......A new and efficient mini slug test method for the determination of local hydraulic conductivities in unconfined sandy aquifers is developed. The slug test is performed in a small-diameter (1 inch) driven well with a 0.25 m screen just above the drive point. The screened drive point can be driven...... distributed measurements of a local hydraulic conductivity at a tracer test site at Vejen, Denmark. The mini slug test results calculated by a modified Dax slug test analysing method, applying the elastic storativity in the Dax equations instead of the specific yield, are in good accordance with the results...

  10. Testing for Nonlinearity in Dynamic Characteristics of Vertical Upward Oil-Gas-Water Three-phase Bubble and Slug Flows

    Institute of Scientific and Technical Information of China (English)

    朱雷; 金宁德; 高忠科; 杜萌; 王振亚

    2012-01-01

    Based on the conductance fluctuation signals measured from vertical upward oil-gas-water three-phase flow experiment, time frequency representation and surrogate data method were used to investigate dynamical characteristics of oil-in-water type bubble and slug flows. The results indicate that oil-in-water type bubble flow will turn to deterministic motion with the increase of oil phase fraction f o and superficial gas velocity U sg under fixed flowrate of oil-water mixture Q mix . The dynamics of oil-in-water type slug flow becomes more complex with the increase of U sg under fixed flowrate of oil-water mixture. The change of f o leads to irregular influence on the dynamics of slug flow. These interesting findings suggest that the surrogate data method can be a faithful tool for characterizing dynamic characteristics of oil-in-water type bubble and slug flows.

  11. Bubbling bed catalytic hydropyrolysis process utilizinig larger catalyst particles and small biomass particles featuring an anti-slugging reactor

    Energy Technology Data Exchange (ETDEWEB)

    Marker, Terry L.; Felix, Larry G.; Linck, Martin B.; Roberts, Michael J.

    2016-12-06

    This invention relates to a process for thermochemically transforming biomass or other oxygenated feedstocks into high quality liquid hydrocarbon fuels. In particular, a catalytic hydropyrolysis reactor, containing a deep bed of fluidized catalyst particles is utilized to accept particles of biomass or other oxygenated feedstocks that are significantly smaller than the particles of catalyst in the fluidized bed. The reactor features an insert or other structure disposed within the reactor vessel that inhibits slugging of the bed and thereby minimizes attrition of the catalyst. Within the bed, the biomass feedstock is converted into a vapor-phase product, containing hydrocarbon molecules and other process vapors, and an entrained solid char product, which is separated from the vapor stream after the vapor stream has been exhausted from the top of the reactor. When the product vapor stream is cooled to ambient temperatures, a significant proportion of the hydrocarbons in the product vapor stream can be recovered as a liquid stream of hydrophobic hydrocarbons, with properties consistent with those of gasoline, kerosene, and diesel fuel. Separate streams of gasoline, kerosene, and diesel fuel may also be obtained, either via selective condensation of each type of fuel, or via later distillation of the combined hydrocarbon liquid.

  12. Bubbling bed catalytic hydropyrolysis process utilizing larger catalyst particles and smaller biomass particles featuring an anti-slugging reactor

    Science.gov (United States)

    Marker, Terry L; Felix, Larry G; Linck, Martin B; Roberts, Michael J

    2014-09-23

    This invention relates to a process for thermochemically transforming biomass or other oxygenated feedstocks into high quality liquid hydrocarbon fuels. In particular, a catalytic hydropyrolysis reactor, containing a deep bed of fluidized catalyst particles is utilized to accept particles of biomass or other oxygenated feedstocks that are significantly smaller than the particles of catalyst in the fluidized bed. The reactor features an insert or other structure disposed within the reactor vessel that inhibits slugging of the bed and thereby minimizes attrition of the catalyst. Within the bed, the biomass feedstock is converted into a vapor-phase product, containing hydrocarbon molecules and other process vapors, and an entrained solid char product, which is separated from the vapor stream after the vapor stream has been exhausted from the top of the reactor. When the product vapor stream is cooled to ambient temperatures, a significant proportion of the hydrocarbons in the product vapor stream can be recovered as a liquid stream of hydrophobic hydrocarbons, with properties consistent with those of gasoline, kerosene, and diesel fuel. Separate streams of gasoline, kerosene, and diesel fuel may also be obtained, either via selective condensation of each type of fuel, or via later distillation of the combined hydrocarbon liquid.

  13. Bubbling bed catalytic hydropyrolysis process utilizinig larger catalyst particles and small biomass particles featuring an anti-slugging reactor

    Science.gov (United States)

    Marker, Terry L.; Felix, Larry G.; Linck, Martin B.; Roberts, Michael J.

    2016-12-06

    This invention relates to a process for thermochemically transforming biomass or other oxygenated feedstocks into high quality liquid hydrocarbon fuels. In particular, a catalytic hydropyrolysis reactor, containing a deep bed of fluidized catalyst particles is utilized to accept particles of biomass or other oxygenated feedstocks that are significantly smaller than the particles of catalyst in the fluidized bed. The reactor features an insert or other structure disposed within the reactor vessel that inhibits slugging of the bed and thereby minimizes attrition of the catalyst. Within the bed, the biomass feedstock is converted into a vapor-phase product, containing hydrocarbon molecules and other process vapors, and an entrained solid char product, which is separated from the vapor stream after the vapor stream has been exhausted from the top of the reactor. When the product vapor stream is cooled to ambient temperatures, a significant proportion of the hydrocarbons in the product vapor stream can be recovered as a liquid stream of hydrophobic hydrocarbons, with properties consistent with those of gasoline, kerosene, and diesel fuel. Separate streams of gasoline, kerosene, and diesel fuel may also be obtained, either via selective condensation of each type of fuel, or via later distillation of the combined hydrocarbon liquid.

  14. Combination of rapamycin, CI-1040, and 17-AAG inhibits metastatic capacity of prostate cancer via Slug inhibition.

    Directory of Open Access Journals (Sweden)

    Guanxiong Ding

    Full Text Available Though prostate cancer (PCa has slow progression, the hormone refractory (HRCP and metastatic entities are substantially lethal and lack effective treatments. Transcription factor Slug is critical in regulating metastases of various tumors including PCa. Here we studied targeted therapy against Slug using combination of 3 drugs targeting 3 pathways respectively converging via Slug and further regulating PCa metastasis. Using in vitro assays we confirmed that Slug up-regulation incurred inhibition of E-cadherin that was anti-metastatic, and inhibited Bim-regulated cell apoptosis in PCa. Upstream PTEN/Akt, mTOR, Erk, and AR/Hsp90 pathways were responsible for Slug up-regulation and each of these could be targeted by rapamycin, CI-1040, and 17-AAG respectively. In 4 PCa cell lines with different traits in terms of PTEN loss and androgen sensitivity we tested the efficacy of mono- and combined therapy with the drugs. We found that metastatic capacity of the cells was maximally inhibited only when all 3 drugs were combined, due to the crosstalk between the pathways. 17-AAG decreases Slug expression via blockade of HSP90-dependent AR stability. Combination of rapamycin and CI-1040 diminishes invasiveness more potently in PCa cells that are androgen insensitive and with PTEN loss. Slug inhibited Bim-mediated apoptosis that could be rescued by mTOR/Erk/HSP90 inhibitors. Using mouse models for circulating PCa DNA quantification, we found that combination of mTOR/Erk/HSP90 inhibitors reduced circulating PCa cells in vivo significantly more potently than combination of 2 or monotherapy. Conclusively, combination of mTOR/Erk/Hsp90 inhibits metastatic capacity of prostate cancer via Slug inhibition.

  15. Slug signaling is up-regulated by CCL21/CCR7 [corrected] to induce EMT in human chondrosarcoma.

    Science.gov (United States)

    Li, Guosong; Yang, Yanjun; Xu, Siliang; Ma, Lifeng; He, Mingtang; Zhang, Ziqing

    2015-02-01

    In recent decades, the CXC chemokine receptor 7 (CCR7) [corrected] and its ligand CCL21 have been extensively reported to be associated with tumorigenesis. Meanwhile, Slug signaling induces the epithelial-mesenchymal transition (EMT) process in chondrosarcoma development. In the present study, we explored the functions of CCL21/CCR7 [corrected] in Slug-mediated EMT in the chondrosarcoma. We analyzed protein expression of CCR7 [corrected] and Slug in human chondrosarcoma samples. Effects of CCR7 [corrected] on chondrosarcoma cells were assessed by in vitro assays. Additionally, CCR7 [corrected] pathways were further investigated by pharmacological and genetic approaches. We found that the altered CCR7 [corrected] (81.7 %) and Slug (85.0 %) expression in human chondrosarcoma tissues were significantly associated with grade, recurrence, and 5-year overall survival. According to in vitro assays, CCL21 stimulation induced the expression of phosph-ERK, phosph-AKT, Slug and N-cadherin in SW1353 cells, while the expression of E-cadherin was down-regulated. Furthermore, Slug signaling modulated E- to N-cadherin switch, which was influenced by the kinase inhibitor PD98059 and LY294002. In addition, the genetic silencing of Slug inhibited the capacity of migration and invasion of SW1353 cells. In conclusion, CCL21/CCR7 [corrected] pathway activates ERK and PI3K/AKT signallings to up-regulate Slug pathway, leading to the occurrence of EMT process in human chondrosarcoma. This study lays a new foundation for molecule-targeted therapy of human chondrosarcoma.

  16. Development of novel sustained release matrix pellets of betahistine dihydrochloride: effect of lipophilic surfactants and co-surfactants.

    Science.gov (United States)

    Shamma, Rehab Nabil; Basalious, Emad B; Shoukri, Raguia

    2012-01-01

    Sustained release matrix pellets of the freely water soluble drug, betahistine dihydrochloride (BH), were prepared using freeze pelletization technique. Different waxes and lipids (cetyl alcohol, beeswax, glyceryl tripalmitate (GTP) and glyceryl tristearate) were evaluated for the preparation of matrix pellets. A D-optimal design was employed for the optimization and to explore the effect of drug loading (X(1)), concentration of lipophilic surfactant (X(2)), concentration of co-surfactant (X(3)) and wax type (X(4)) on the release extent of the drug from matrix pellets. The entrapment efficiency (Y(1)), pellet diameter (Y(2)), and the percentage drug released at given times were selected as dependent variables. Results revealed a significant impact of all independent variables on drug release from the formulated pellets. The lipophilic surfactant significantly increased both the entrapment efficiency and the in vitro drug release and significantly decreased the pellet size. The optimized BH-loaded pellets were composed of 19.95% drug loading, 9.95% Span(®) 80 (surfactant), 0.25% Capmul(®) (co-surfactant) using glyceryl tripalmitate as a matrix former. The release profiles of the drug from hard gelatin capsule containing optimized pellets equivalent to 32 mg BH was similar to that of target release model for once-daily administration based on similarity factor. It could be concluded that a promising once-daily capsule containing sustained release pellets of BH was successfully designed.

  17. Kinetics of degradation of surfactant-solubilized fluoranthene by a Sphingomonas paucimobilis

    Energy Technology Data Exchange (ETDEWEB)

    Willumsen, P.A. (National Environmental Research Institute, Roskilde (Denmark). Dept. of Marine Ecology and Microbiology); Arvin, E. (Technical Univ. of Denmark, Lyngby (Denmark). Dept. of Environmental Science and Engineering)

    1999-08-01

    To achieve a better quantitative understanding of the stimulating or inhibiting effect of surfactants on the metabolism of polycyclic aromatic hydrocarbons (PAHs), a biodegradation model describing solubilization, bioavailability, and biodegradation of crystalline fluoranthene is proposed and used to model experimental data. The degradation was investigated in batch systems containing the PAH-degrading bacterium Sphingomonas paucimobilis strain EPA505, the nonionic surfactant Triton X-100, and a fluoranthene-amended liquid mineral salts medium. Surfactant-enhanced biodegradation is complex; however, the biodegradation model predicted fluoranthene disappearance and the initial mineralization well. Surfactant-amendment did increase fluoranthene mineralization rates by strain EPA505; however, the increases were not proportional to the rates of fluoranthene solubilization. The surfactant clearly influenced the microbial PAH metabolism as indicated by a rapid accumulation of colored products and by a surfactant -related decreased in the overall extent of fluoranthene mineralization. Model estimations of the bioavailability of micelle-solubilized fluoranthene, the relatively fast fluoranthene disappearance, and the accumulation of extracellular compounds in the degradation system suggest that low availability of micellar fluoranthene is not the only factor controlling surfactant-enhanced biodegradation. Also factors such as the extent of accumulation and bioavailability of the PAH metabolites and the crystalline solubilization rate in the presence of surfactants may determine the overall effect of surfactant-enhanced biodegradation of high molecular weight PAHs.

  18. Treatment with exogenous surfactant stimulates endogenous surfactant synthesis in premature infants with respiratory distress syndrome

    NARCIS (Netherlands)

    Bunt, JEH; Carnielli, VP; Janssen, DJ; Wattimena, JLD; Hop, WC; Sauer, PJ; Zimmermann, LJI

    2000-01-01

    Objective: Treatment of preterm infants with respiratory distress syndrome (RDS) with exogenous surfactant has greatly improved clinical outcome. Some infants require multiple doses, and it has not been studied whether these large amounts of exogenous surfactant disturb endogenous surfactant metabol

  19. Suppression of Invasion and Metastasis of Triple-Negative Breast Cancer Lines by Pharmacological or Genetic Inhibition of Slug Activity

    Directory of Open Access Journals (Sweden)

    Giovanna Ferrari-Amorotti

    2014-12-01

    Full Text Available Most triple-negative breast cancers (TNBCs exhibit gene expression patterns associated with epithelial-to-mesenchymal transition (EMT, a feature that correlates with a propensity for metastatic spread. Overexpression of the EMT regulator Slug is detected in basal and mesenchymal-type TNBCs and is associated with reduced E-cadherin expression and aggressive disease. The effects of Slug depend, in part, on the interaction of its N-terminal SNAG repressor domain with the chromatin-modifying protein lysine demethylase 1 (LSD1; thus, we investigated whether tranylcypromine [also known as trans-2-phenylcyclopropylamine hydrochloride (PCPA or Parnate], an inhibitor of LSD1 that blocks its interaction with Slug, suppresses the migration, invasion, and metastatic spread of TNBC cell lines. We show here that PCPA treatment induces the expression of E-cadherin and other epithelial markers and markedly suppresses migration and invasion of TNBC cell lines MDA-MB-231 and BT-549. These effects were phenocopied by Slug or LSD1 silencing. In two models of orthotopic breast cancer, PCPA treatment reduced local tumor growth and the number of lung metastases. In mice injected directly in the blood circulation with MDA-MB-231 cells, PCPA treatment or Slug silencing markedly inhibited bone metastases but had no effect on lung infiltration. Thus, blocking Slug activity may suppress the metastatic spread of TNBC and, perhaps, specifically inhibit homing/colonization to the bone.

  20. Differential expression of the epithelial mesenchymal transition factors Snail, Slug, Twist, TGF-β, and E-cadherin in ameloblastoma.

    Science.gov (United States)

    Kurioka, Kagami; Wato, Masahiro; Iseki, Tomio; Tanaka, Akio; Morita, Shosuke

    2017-06-01

    Epithelial mesenchymal transition (EMT), the transition of epithelial cells into motile mesenchymal cells, plays an important role in embryogenesis, cancer invasion, and metastasis. Ameloblastomas are common epithelial odontogenic tumors, occurring exclusively in the mandible with locally invasive growth. Thirty-seven ameloblastoma cases were evaluated for the involvement of EMT by immunohistochemical staining and western blotting using antibodies against Slug, Snail, Twist, TGF-β, and E-cadherin. Double immunostaining was also performed. Slug and TGF-β were expressed in the nuclei of peripheral and stellate reticulum cells of ameloblastoma nests. Twenty cases of Snail, 36 of Slug, 8 of Twist, and 19 of TGF-β showed strong expression in tumor cells in follicular and plexiform patterns. Expression of Slug and TGF-β increased in regions where the expression of E-cadherin was reduced. EMT was found to be associated with the local invasive growth of ameloblastoma. These data suggest that reduced expression of E-cadherin and over-expression of Slug, Snail, and TGF-β induce EMT. Given that ameloblastomas are characterized by local invasiveness, EMT might be related to their development. Thus, strong expression of Slug and TGF-β and reduced expression of E-cadherin might be related to the local invasiveness of ameloblastoma.

  1. Electrochemical Oscillations Induced by Surfactants

    Institute of Scientific and Technical Information of China (English)

    翟俊红; 贺占博

    2003-01-01

    A new type of electrochemical oscillation induced by surfactant was observed in experiments. The electrochemical system is a Daniell cell with a copper rod in CuSO4 aqueous and an aluminum rod in Al(NO3)3 aqueous as electrodes. The surfactants are CTAB, TX-100, SLS. The addition of trace surfactant solution by a micro-syringe made the original monotonously changing electrochemical system produce obvious periodic phenomena. At the mean time, the copper ion selective electrode and Hg2SO4 reference electrode were used to monitor the copper electrode reaction and determine its rate constant k of first order reaction. According to the experimental results of electrode reaction kinetics, the possible mechanism was found to be the polarization induced from the directional adsorption of trace surfactant on the electrode surface. That is the electrochemical oscillations.

  2. The identification, localization, and pharmacology of FMRFamide-related peptides and SCPB in the penis and crop of the terrestrial slug, Limax maximus.

    Science.gov (United States)

    Krajniak, K G; Greenberg, M J; Price, D A; Doble, K E; Lee, T D

    1989-01-01

    1. The molluscan neuropeptides FMRFamide, pQDPFLRFamide, and SCPB were tested on the isolated crop and penis of the terrestraial slug, Limax maximus. FMRFamide and pQDPFLRFamide stimulated the penis and inhibited contractions of the crop. In contrast, SCPB either stimulated or relaxed the penis and increased the tone of the crop. 2. Fibers and varicosities containing immunoreactive (ir-) FMRFamide and ir-SCPB were located in the penis and crop. 3. Extracts of penes, crops, ganglia, and whole animals all contained FMRFamide, FLRFamide, SDPFLRFamide, NDPFLRFamide, and pQDPFLRFamide. 4. These results suggest that the FMRFamide-related peptides and SCPB are involved in the regulation of the reproductive and digestive activities of Limax.

  3. A criterion for the onset of slugging in horizontal stratified air-water countercurrent flow

    Energy Technology Data Exchange (ETDEWEB)

    Chun, Moon-Hyun; Lee, Byung-Ryung; Kim, Yang-Seok [Korea Advanced Institute of Science and Technology, Taejon (Korea, Republic of)] [and others

    1995-09-01

    This paper presents an experimental and theoretical investigation of wave height and transition criterion from wavy to slug flow in horizontal air-water countercurrent stratified flow conditions. A theoretical formula for the wave height in a stratified wavy flow regime has been developed using the concept of total energy balance over a wave crest to consider the shear stress acting on the interface of two fluids. From the limiting condition of the formula for the wave height, a necessary criterion for transition from a stratified wavy flow to a slug flow has been derived. A series of experiments have been conducted changing the non-dimensional water depth and the flow rates of air in a horizontal pipe and a duct. Comparisons between the measured data and the predictions of the present theory show that the agreement is within {plus_minus}8%.

  4. Gas Slug Microfluidics: A Unique Tool for Ultrafast, Highly Controlled Growth of Iron Oxide Nanostructures.

    Science.gov (United States)

    Larrea, Ane; Sebastian, Victor; Ibarra, Alfonso; Arruebo, Manuel; Santamaria, Jesus

    2015-06-23

    The use of nanomaterials in real life applications is often hampered by our inability to produce them in large quantities while preserving their desired properties in terms of size, shape, and crystalline phase. Here we present a novel continuous method to synthesize nanostructures with an unprecedented degree of control regarding their properties. In particular, the excellent properties of microreactors for chemical synthesis are enhanced by the introduction of gas slugs of tailored composition. Slug dynamics accelerate mixing, reduce processing times (from hours in batch processes to minutes or even seconds), and, depending on the gas atmosphere used, allows one to accurately control the crystalline phase and shape of the resulting nanostructures. Inert (N2), oxidizing (O2), or reducing (CO, H2) gases were used, leading to different morphologies and crystalline structures in a high yield, highly reproducible fabrication process.

  5. Persurf, a New Method to Improve Surfactant Delivery: A Study in Surfactant Depleted Rats

    OpenAIRE

    2012-01-01

    PURPOSE: Exogenous surfactant is not very effective in adults with ARDS, since surfactant does not reach atelectatic alveoli. Perfluorocarbons (PFC) can recruit atelectatic areas but do not replace impaired endogenous surfactant. A surfactant-PFC-mixture could combine benefits of both therapies. The aim of the proof-of-principal-study was to produce a PFC-in-surfactant emulsion (Persurf) and to test in surfactant depleted Wistar rats whether Persurf achieves I.) a more homogenous pulmonary di...

  6. Gas Slug Microfluidics: A Unique Tool for Ultrafast, Highly Controlled Growth of Iron Oxide Nanostructures

    OpenAIRE

    Larrea, Ane; Sebastian, Victor; Ibarra, Alfonso; Arruebo, Manuel; Santamaria, Jesus

    2015-01-01

    The use of nanomaterials in real life applications is often hampered by our inability to produce them in large quantities while preserving their desired properties in terms of size, shape, and crystalline phase. Here we present a novel continuous method to synthesize nanostructures with an unprecedented degree of control regarding their properties. In particular, the excellent properties of microreactors for chemical synthesis are enhanced by the introduction of gas slugs of tailored composit...

  7. A field proof-of-concept of tomographic slug tests in an anisotropic littoral aquifer

    Science.gov (United States)

    Paradis, Daniel; Gloaguen, Erwan; Lefebvre, René; Giroux, Bernard

    2016-05-01

    Hydraulic tomography is increasingly recognized as a characterization approach that can image pathways or barriers to flow as well as their connectivity. In this study, we assess the performance of a transient analysis of tomographic slug test head data in estimating heterogeneity in horizontal hydraulic conductivity (Kh), hydraulic conductivity anisotropy (the ratio between vertical and horizontal hydraulic conductivity - Kv/Kh) and specific storage (Ss) under actual field conditions. The tomographic experiment was carried out between two wells in a moderately heterogeneous and highly anisotropic silt and sand littoral aquifer. In this field proof-of-concept, the inversion of the two-dimensional (2D) head dataset was computed with a 2D radial flow algorithm that considers Kh, Kv/Kh, Ss and wellbore storage effects. This study demonstrated that a transient analysis of tomographic slug tests is able to capture the key features of the littoral environment of the test: the vertical profiles of Kh and Kv are indeed in agreement with those from other field and laboratory tests, and Ss values exhibit physically plausible profiles. Furthermore, the simulation of independent inter-well hydraulic tests (slug and pumping tests screened over the entire aquifer) using resolved Kh, Kv/Kh and Ss tomograms produce responses very close to field observations. This study demonstrates that the effects of fine scale heterogeneity that induces K-anisotropy at larger scales can be captured through a transient analysis of tomographic slug tests, which are very difficult to quantify otherwise with conventional hydraulic tests, thus allowing a better representation of properties controlling flow and transport in aquifer systems.

  8. Gastropod seed dispersal: an invasive slug destroys far more seeds in its gut than native gastropods.

    Science.gov (United States)

    Blattmann, Tamara; Boch, Steffen; Türke, Manfred; Knop, Eva

    2013-01-01

    Seed dispersal is one of the most important mechanisms shaping biodiversity, and animals are one of the key dispersal vectors. Animal seed dispersal can directly or indirectly be altered by invasive organisms through the establishment of new or the disruption of existing seed dispersal interactions. So far it is known for a few gastropod species that they ingest and defecate viable plant seeds and consequently act as seed dispersers, referred to as gastropodochory. In a multi-species experiment, consisting of five different plant species and four different gastropod species, we tested with a fully crossed design whether gastropodochory is a general mechanism across native gastropod species, and whether it is altered by the invasive alien slug species Arion lusitanicus. Specifically, we hypothesized that a) native gastropod species consume the seeds from all tested plant species in equal numbers (have no preference), b) the voracious invasive alien slug A. lusitanicus--similarly to its herbivore behaviour--consumes a higher amount of seeds than native gastropods, and that c) seed viability is equal among different gastropod species after gut passage. As expected all tested gastropod species consumed all tested plant species. Against our expectation there was a difference in the amount of consumed seeds, with the largest and native mollusk Helix pomatia consuming most seeds, followed by the invasive slug and the other gastropods. Seed damage and germination rates did not differ after gut passage through different native species, but seed damage was significantly higher after gut passage through the invasive slug A. lusitanicus, and their germination rates were significantly reduced.

  9. Liquid-liquid Slug Flow in a Microchannel Reactor and its Mass Transfer Properties - A Review

    Directory of Open Access Journals (Sweden)

    Rahul Antony

    2014-10-01

    Full Text Available Mass transfer is a basic phenomenon behind many processes like reaction, absorption, extraction etc. Mass transfer plays a significant role in microfluidic systems where the chemical / biological process systems are shrinkened down to a micro scale. Micro reactor system, with its high compatibility and performance, gains a wide interest among the researchers in the recent years. Micro structured reac-tors holds advantages over the conventional types in chemical processes. The significance of micro re-actor not limited to its scalability but to energy efficiency, on-site / on-demand production, reliability, safety, highly controlled outputs, etc. Liquid-liquid two phase reaction in a microreactor system is highly demandable when both reactants are liquids or when air medium cannot be suitable. This arti-cle overviews various liquid-liquid flow regimes in a microchannel. Discussions on the hydrodynamics of flow in micro scale are made. Considering the importance of mass transfer in liquid-liquid systems and the advantage of slug regime over other regimes, the article focuses especially on the mass trans-fer between two liquid phases in slug flow and the details of experimental studies carried out in this area. The advantages of slug flow over other flow regimes in micro structured reactor applications are showcased. © 2014 BCREC UNDIP. All rights reservedReceived: 31st May 2014; Revised: 6th August 2014; Accepted: 14th August 2014How to Cite: Antony, R., Giri Nandagopal, M.S., Sreekumar, N., Rangabhashiyam, S., Selvaraju, N. (2014. Liquid-liquid Slug Flow in a Microchannel Reactor and its Mass Transfer Properties - A Review. Bulletin of Chemical Reaction Engineering & Catalysis,9(3: 207-223. (doi:10.9767/bcrec.9.3.6977.207-223Permalink/DOI: http://dx.doi.org/10.9767/bcrec.9.3.6977.207-223

  10. EMT transcription factors snail and slug directly contribute to cisplatin resistance in ovarian cancer

    Directory of Open Access Journals (Sweden)

    Haslehurst Alexandria M

    2012-03-01

    Full Text Available Abstract Background The epithelial to mesenchymal transition (EMT is a molecular process through which an epithelial cell undergoes transdifferentiation into a mesenchymal phenotype. The role of EMT in embryogenesis is well-characterized and increasing evidence suggests that elements of the transition may be important in other processes, including metastasis and drug resistance in various different cancers. Methods Agilent 4 × 44 K whole human genome arrays and selected reaction monitoring mass spectrometry were used to investigate mRNA and protein expression in A2780 cisplatin sensitive and resistant cell lines. Invasion and migration were assessed using Boyden chamber assays. Gene knockdown of snail and slug was done using targeted siRNA. Clinical relevance of the EMT pathway was assessed in a cohort of primary ovarian tumours using data from Affymetrix GeneChip Human Genome U133 plus 2.0 arrays. Results Morphological and phenotypic hallmarks of EMT were identified in the chemoresistant cells. Subsequent gene expression profiling revealed upregulation of EMT-related transcription factors including snail, slug, twist2 and zeb2. Proteomic analysis demonstrated up regulation of Snail and Slug as well as the mesenchymal marker Vimentin, and down regulation of E-cadherin, an epithelial marker. By reducing expression of snail and slug, the mesenchymal phenotype was largely reversed and cells were resensitized to cisplatin. Finally, gene expression data from primary tumours mirrored the finding that an EMT-like pathway is activated in resistant tumours relative to sensitive tumours, suggesting that the involvement of this transition may not be limited to in vitro drug effects. Conclusions This work strongly suggests that genes associated with EMT may play a significant role in cisplatin resistance in ovarian cancer, therefore potentially leading to the development of predictive biomarkers of drug response or novel therapeutic strategies for

  11. Injection of Nucleate-Boiling Slug Flows into a Heat Exchange Chamber in Microgravity

    Science.gov (United States)

    2015-06-01

    AFRL-AFOSR-UK-TR-2015-0029 Injection of nucleate- boiling slug flows into a heat exchange chamber in microgravity Jaume...2015 2. REPORT TYPE Final Report 3. DATES COVERED (From – To) 20 March 2012 – 19 March 2015 4. TITLE AND SUBTITLE Injection of nucleate- boiling ...method to produce controlled boiling through a localized nucleation cavity feeding a capillary crossflow forming regular trains of bubbles. The main

  12. Fluidization behavior in a circulating slugging fluidized bed reactor. Part II: Plug characteristics

    NARCIS (Netherlands)

    Putten, van I.C.; Sint Annaland, van M.; Weickert, G.

    2007-01-01

    In the transporting square nosed slugging fluidization regime (0.4 < u0 < 1.0m/s) a bed of polyethylene powder with a low density (ρ = 900/kg/m3) and a large particle size distribution (70 < dρ < 1600µm) was operated in two circulating fluidized bed systems (riser diameters 0.044 and 0.105 m). A rel

  13. Modulation of the Proliferation and Metastasis of Human Breast Tumor Cells by SLUG (IDEA)

    Science.gov (United States)

    2007-04-01

    Biochemical and Biophysical Research Communications 353...terminal zinc-finger domains and then 662 C.K. Bailey et al. / Biochemical and Biophysical Research Communications 353 (2007) 661–664recruits either CtBP1...control); (2) blank vectors (negative control); (3 and 4) pGBKT7-hSLUG/pGADT7- hCtBP1. C.K. Bailey et al. / Biochemical and Biophysical Research Communications

  14. EMT transcription factors snail and slug directly contribute to cisplatin resistance in ovarian cancer.

    Science.gov (United States)

    Haslehurst, Alexandria M; Koti, Madhuri; Dharsee, Moyez; Nuin, Paulo; Evans, Ken; Geraci, Joseph; Childs, Timothy; Chen, Jian; Li, Jieran; Weberpals, Johanne; Davey, Scott; Squire, Jeremy; Park, Paul C; Feilotter, Harriet

    2012-03-19

    The epithelial to mesenchymal transition (EMT) is a molecular process through which an epithelial cell undergoes transdifferentiation into a mesenchymal phenotype. The role of EMT in embryogenesis is well-characterized and increasing evidence suggests that elements of the transition may be important in other processes, including metastasis and drug resistance in various different cancers. Agilent 4 × 44 K whole human genome arrays and selected reaction monitoring mass spectrometry were used to investigate mRNA and protein expression in A2780 cisplatin sensitive and resistant cell lines. Invasion and migration were assessed using Boyden chamber assays. Gene knockdown of snail and slug was done using targeted siRNA. Clinical relevance of the EMT pathway was assessed in a cohort of primary ovarian tumours using data from Affymetrix GeneChip Human Genome U133 plus 2.0 arrays. Morphological and phenotypic hallmarks of EMT were identified in the chemoresistant cells. Subsequent gene expression profiling revealed upregulation of EMT-related transcription factors including snail, slug, twist2 and zeb2. Proteomic analysis demonstrated up regulation of Snail and Slug as well as the mesenchymal marker Vimentin, and down regulation of E-cadherin, an epithelial marker. By reducing expression of snail and slug, the mesenchymal phenotype was largely reversed and cells were resensitized to cisplatin. Finally, gene expression data from primary tumours mirrored the finding that an EMT-like pathway is activated in resistant tumours relative to sensitive tumours, suggesting that the involvement of this transition may not be limited to in vitro drug effects. This work strongly suggests that genes associated with EMT may play a significant role in cisplatin resistance in ovarian cancer, therefore potentially leading to the development of predictive biomarkers of drug response or novel therapeutic strategies for overcoming drug resistance.

  15. Gas6/Axl pathway promotes tumor invasion through the transcriptional activation of Slug in hepatocellular carcinoma.

    Science.gov (United States)

    Lee, Hsin-Jung; Jeng, Yung-Ming; Chen, Yu-Ling; Chung, Ling; Yuan, Ray-Hwang

    2014-04-01

    Hepatocellular carcinoma (HCC) is one of the most common fatal cancers worldwide. Other than the sorafenib treatment, no effective systemic therapy has been available thus far. Most targets in molecularly targeted therapy for cancer are receptor tyrosine kinases (RTKs). Therefore, identifying activated RTKs in HCC is critical for developing new molecularly targeted therapies. Using a phospho-RTK array, we found that Axl is one of the most frequently activated RTKs in liver cancer cell lines. The knockdown of Axl by RNA interference significantly reduced cell migration and invasion in the HCC cell lines HA22T and Mahlavu. Stimulation of HCC cell lines by Axl ligand growth arrest-specific 6 (Gas6) enhanced cell migration and invasion. The Gas6/Axl pathway enhanced the expression of the epithelial-mesenchymal transition-inducing transcription factor Slug, which is essential for the invasion-promoting activity of Axl. Treating HCC cells with the Axl inhibitor bosutinib suppressed Slug expression and decreased the invasiveness of HCC cell lines. These findings indicate that Gas6/Axl regulates tumor invasion through the transcriptional activation of Slug.

  16. Differential expression of transcription factors Snail, Slug, SIP1, and Twist in ameloblastoma.

    Science.gov (United States)

    Siar, Chong Huat; Ng, Kok Han

    2014-01-01

    Epithelial-to-mesenchymal transition (EMT) via the mechanism of transcription repression is a crucial process for the induction of invasiveness in many human tumors. Ameloblastoma is a benign odontogenic epithelial neoplasm with a locally infiltrative behavior. Twist, an EMT promoter, has been implicated in its invasiveness. The roles of the other transcription factors remain unclarified. Four transcription factors, namely Snail, Slug, SIP1, and Twist, were examined immunohistochemically in 64 ameloblastoma [18 unicystic (UA), 20 solid/multicystic (SA), 4 desmoplastic (DA), and 22 recurrent (RA)]. All four transcription factors were differentially expressed in ameloblastoma [Snail: n = 60/64 (94%); Slug: n = 21/64 (33%); SIP: n = 18/64 (28%); Twist: n = 26/64 (41%)] (P 0.05). Intracellular protein localization was predominantly nuclear for Snail, cytoplasmic>nuclear for Slug and SIP1, and cytoplasmic/nuclear for Twist. Overexpression of Snail in most subsets (UA = 18/18; SMA = 19/20; DA = 4/4; RA = 19/22) compared with the other transcription factors (P ameloblastoma. Overexpression of Snail in most subsets suggests that this molecule is most likely the prototype transcription factor involved in inducing EMT in the ameloblastoma. © 2013 John Wiley & Sons A/S. Published by Blackwell Publishing Ltd.

  17. Interfacial area, velocity and void fraction in two-phase slug flow

    Energy Technology Data Exchange (ETDEWEB)

    Kojasoy, G. [Univ. of Wisconsin, Milwaukee, WI (United States); Riznic, J.R. [Atomic Energy Control Board, Ottawa (Canada)

    1997-12-31

    The internal flow structure of air-water plug/slug flow in a 50.3 mm dia transparent pipeline has been experimentally investigated by using a four-sensor resistivity probe. Liquid and gas volumetric superficial velocities ranged from 0.55 to 2.20 m/s and 0.27 to 2.20 m/s, respectively, and area-averaged void fractions ranged from about 10 to 70%. The local distributions of void fractions, interfacial area concentration and interface velocity were measured. Contributions from small spherical bubbles and large elongated slug bubbles toward the total void fraction and interfacial area concentration were differentiated. It was observed that the small bubble void contribution to the overall void fraction was small indicating that the large slug bubble void fraction was a dominant factor in determining the total void fraction. However, the small bubble interfacial area contribution was significant in the lower and upper portions of the pipe cross sections.

  18. Antimicrobial Potential of Bacteria Associated with Marine Sea Slugs from North Sulawesi, Indonesia

    Directory of Open Access Journals (Sweden)

    Nils Böhringer

    2017-06-01

    Full Text Available Nudibranchia, marine soft-bodied organisms, developed, due to the absence of a protective shell, different strategies to protect themselves against putative predators and fouling organisms. One strategy is to use chemical weapons to distract predators, as well as pathogenic microorganisms. Hence, these gastropods take advantage of the incorporation of chemical molecules. Thereby the original source of these natural products varies; it might be the food source, de novo synthesis from the sea slug, or biosynthesis by associated bacteria. These bioactive molecules applied by the slugs can become important drug leads for future medicinal drugs. To test the potential of the associated bacteria, the latter were isolated from their hosts, brought into culture and extracts were prepared and tested for antimicrobial activities. From 49 isolated bacterial strains 35 showed antibiotic activity. The most promising extracts were chosen for further testing against relevant pathogens. In that way three strains showing activity against methicillin resistant Staphylococcus aureus and one strain with activity against enterohemorrhagic Escherichia coli, respectively, were identified. The obtained results indicate that the sea slug associated microbiome is a promising source for bacterial strains, which hold the potential for the biotechnological production of antibiotics.

  19. Design considerations regarding slug ruptures in the intermediate power level reactor

    Energy Technology Data Exchange (ETDEWEB)

    Pearl, W.L.; Pursel, C.A.

    1954-11-01

    The minimum shutdown time, to permit accessibility, for the Intermediate Power Reactor is estimated to be 38 hours. In case the reactor were shutdown following each rupture this long shutdown period would have serious disadvantages. The desirability of being able to make firm power commitments (independent of slug ruptures) has led to a study of the possibility of continuous operation following a rupture. There is evidence to indicate that, at the proposed water temperature, the rate of corrosion of uranium may be so high that at least a major portion of the rupture products may have entered the system before the reactor can be shutdown. A pushout of the affected column would then be a pushout of only those slugs which are still intact and the problem would still remain of removing the rupture products from the system. The first portion of this report is concerned with the rate of corrosion of a slug following rupture and the possible limitations to the principle of non-shutdown operation. These limitations include a flow stoppage by the ruptured can, undue increase in gamma activity, increased corrosion by the rupture products, and adherence of rupture products to the piping. The latter portion of the document is concerned with design considerations of the shielding and water plant so as to eliminate or minimize the effects of the introduction of rupture products into the cooling system. 7 refs., 2 figs.

  20. Anaerobic digestion of aircraft deicing fluid wastes: interactions and toxicity of corrosion inhibitors and surfactants.

    Science.gov (United States)

    Gruden, Cyndee L; Hernandez, Mark

    2002-01-01

    Corrosion inhibitors and surfactants are present in aircraft deicing fluids (ADFs) at significant concentrations (> 1% w/w). The purpose of this research was to study the interactions of a common nonionic surfactant with the commercially significant corrosion inhibitors used in modern ADF (4- and 5-methylbenzotriazole [MeBT]), and to determine the effects of their mixture on the conventional anaerobic digestion process. In mesophilic anaerobic microcosms codigesting wastewater solids, propylene glycol, and MeBT, increasing surfactant levels resulted in enhanced MeBT sorption on digester solids. As judged by anaerobic toxicity assays, responses from digesters containing surfactant concentrations below their critical micelle concentration (CMC) suggested that low nonionic surfactant concentrations could facilitate a reduction in the apparent toxicity of MeBT. In microcosms exposed to surfactant concentrations above their CMC, no increase in MeBT solubility was observed, and the anaerobic toxicity response corresponded to control systems not containing surfactant. Direct microscopic measurements of digesting biomass using fluorescent phylogenetic probes (fluorescent in situ hybridization) revealed that members of the domain Bacteria were more sensitive to MeBT in the presence of surfactant than were members of the domain Archaea.

  1. In vivo evaluation of the inhibitory capacity of human plasma on exogenous surfactant function

    NARCIS (Netherlands)

    B.F. Lachmann (Burkhard); E.P. Eijking (Eric); K.L. So; D.A.M.P.J. Gommers (Diederik)

    1994-01-01

    textabstractObjective: The adult respiratory distress syndrome (ARDS) and neonatal respiratory distress syndrome (RDS) are characterized by high permeability pulmonary edema which contains plasma-derived proteins inhibiting pulmonary surfactant function. Currently, discussion continues as to what do

  2. Synthesis and Surface Activity of Novel Triazole-based Cationic Gemini Surfactants

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    The synthesis and surfactant activities of two new cationic gemini surfactants containingtriazole compound as spacer were described. Their critical micelle concentrations (CMC), whichare 1.8 × l0-4 mol/L and 3.9× 10-4 mol/L respectively, are much lower than that of conventionalsurfactant cetyltrimethyl ammonium chloride (CTAC). In addition, compared with some geminisurfactants containing phenylene, xylylene and stilbenyl as spacer, this new kind of surfactants hasgood solubility in water at room temperature because of containing more hydrophilic groups oratoms in molecules.

  3. Effect of alkyl chain asymmetry on catanionic mixtures of hydrogenated and fluorinated surfactants.

    Science.gov (United States)

    Blanco, Elena; Rodriguez-Abreu, Carlos; Schulz, Pablo; Ruso, Juan M

    2010-01-15

    In this work we studied and compared the physicochemical properties of the catanionic mixtures cetyltrimethyl-ammonium bromide-sodium dodecanoate, cetyltrimethyl-ammonium bromide-sodium perfluorodacanoate, octyltrimethylammonium bromide-sodium perfluorodacanoate and cetyltrimethyl-ammonium bromide-sodium octanoate by a combination of rheological, transmission electron microscopy (TEM) and polarized optical microscopy measurements. The binary mixtures of the surfactants have been analyzed at different mixed ratios and total concentration of the mixture. Mixtures containing a perfluorinated surfactant are able to form lamellar liquid crystals and stable spontaneous vesicles. Meanwhile, system containing just hydrogenated surfactants form hexagonal phases or they are arranged in elongated aggregates.

  4. Surfactants enhance recovery of poorly soluble drugs during microdialysis sampling

    DEFF Research Database (Denmark)

    Koplin, Sebastian; Kumpugdee-Vollrath, Mont; Bauer-Brandl, Annette

    2017-01-01

    Aim of this project was to investigate the applicability of a recently developed in vitro microdialysis-sampling approach in connection with a dissolution-/permeation (D/P) system, especially the impact of surfactants within the perfusion fluid. The D/P-system is based on side-by-side chambers...... drug-dissolution (-release) and drug permeation. Furthermore, it should allow quantification of the unbound (free) drug concentration. In the first step, it was assessed, if the addition of the anionic surfactant sodium dodecyl sulphate (SDS) to the perfusate of the microdialysis system affects...... celecoxib, i.e. the fraction of drug, which is not associated with taurocholate surfactant micelles. In buffer, the measured concentrations matched the overall CXB concentrations. By the use of SDS-containing perfusates microdialysis sampling enabled reliable quantification of minute amounts of free CXB...

  5. Spatiotemporal measurement of surfactant distribution on gravity-capillary waves

    CERN Document Server

    Strickland, Stephen L; Daniels, Karen E

    2015-01-01

    Materials adsorbed to the surface of a fluid -- for instance, crude oil, biogenic slicks, or industrial/medical surfactants -- will move in response to surface waves. Due to the difficulty of non-invasive measurement of the spatial distribution of a molecular monolayer, little is known about the dynamics that couple the surface waves and the evolving density field. Here, we report measurements of the spatiotemporal dynamics of the density field of an insoluble surfactant driven by gravity-capillary waves in a shallow cylindrical container. Standing Faraday waves and traveling waves generated by the meniscus are superimposed to create a non-trivial surfactant density field. We measure both the height field of the surface using moir\\'e-imaging, and the density field of the surfactant via the fluorescence of NBD-tagged phosphatidylcholine, a lipid. Through phase-averaging stroboscopically-acquired images of the density field, we determine that the surfactant accumulates on the leading edge of the traveling menis...

  6. Flow improvers for water injection based on surfactants

    Energy Technology Data Exchange (ETDEWEB)

    Oskarsson, H.; Uneback, I.; Hellsten, M.

    2006-03-15

    In many cases it is desirable to increase the flow of injection water when an oil well deteriorates. It is very costly in offshore operation to lay down an additional water pipe to the injection site. Flow improvers for the injection water will thus be the most cost-effective way to increase the flow rate. During the last years water-soluble polymers have also been applied for this purpose. These drag-reducing polymers are however only slowly biodegraded which has been an incentive for the development of readily biodegradable surfactants as flow improvers for injection water. A combination of a zwitterionic and an anionic surfactant has been tested in a 5.5 inch, 700 m long flow loop containing sulphate brine with salinity similar to sea water. A drag reduction between 75 and 80% was achieved with 119 ppm in solution of the surfactant blend at an average velocity of 1.9 m/s and between 50 and 55% at 2.9 m/s. The surfactants in this formulation were also found to be readily biodegradable in sea water and low bio accumulating which means they have an improved environmental profile compared to the polymers used today. Due to the self-healing properties of the drag-reducing structures formed by surfactants, these may be added before the pump section - contrary to polymers which are permanently destroyed by high shear forces. (Author)

  7. The physicochemistry and percolation behavior of microemulsions as a function of chain length of cosurfactant and surfactant

    National Research Council Canada - National Science Library

    Purva Thatai; Ashok K. Tiwary; Bharti Sapra

    2016-01-01

    ...) stabilized by mixtures containing polysorbates (C12-C18) as surfactants and n-alkanols (C2-C6) as cosurfactants. Distribution coefficients and Gibbs free energy were also determined for the systems containing polyoxyethylene sorbitan monolaurate...

  8. Two new disposable bioreactors for plant cell culture: The wave and undertow bioreactor and the slug bubble bioreactor.

    Science.gov (United States)

    Terrier, Bénédicte; Courtois, Didier; Hénault, Nicolas; Cuvier, Arnaud; Bastin, Maryse; Aknin, Aziz; Dubreuil, Julien; Pétiard, Vincent

    2007-04-01

    The present article describes two novel flexible plastic-based disposable bioreactors. The first one, the WU bioreactor, is based on the principle of a wave and undertow mechanism that provides agitation while offering convenient mixing and aeration to the plant cell culture contained within the bioreactor. The second one is a high aspect ratio bubble column bioreactor, where agitation and aeration are achieved through the intermittent generation of large diameter bubbles, "Taylor-like" or "slug bubbles" (SB bioreactor). It allows an easy volume increase from a few liters to larger volumes up to several hundred liters with the use of multiple units. The cultivation of tobacco and soya cells producing isoflavones is described up to 70 and 100 L working volume for the SB bioreactor and WU bioreactor, respectively. The bioreactors being disposable and pre-sterilized before use, cleaning, sterilization, and maintenance operations are strongly reduced or eliminated. Both bioreactors represent efficient and low cost cell culture systems, applicable to various cell cultures at small and medium scale, complementary to traditional stainless-steel bioreactors.

  9. Surfactant for pediatric acute lung injury.

    Science.gov (United States)

    Willson, Douglas F; Chess, Patricia R; Notter, Robert H

    2008-06-01

    This article reviews exogenous surfactant therapy and its use in mitigating acute lung injury (ALI) and the acute respiratory distress syndrome (ARDS) in infants, children, and adults. Biophysical and animal research documenting surfactant dysfunction in ALI/ARDS is described, and the scientific rationale for treatment with exogenous surfactant is discussed. Major emphasis is placed on reviewing clinical studies of surfactant therapy in pediatric and adult patients who have ALI/ARDS. Particular advantages from surfactant therapy in direct pulmonary forms of these syndromes are described. Also discussed are additional factors affecting the efficacy of exogenous surfactants in ALI/ARDS.

  10. The Effect of Grazing by the Slug Arion Vulgaris, Arion Rufus and Deroceras Reticulatum (Gastropoda: Pulmonata: Stylommatophora on Leguminous Plants and other Small-Area Crops

    Directory of Open Access Journals (Sweden)

    Kozłowski Jan

    2014-07-01

    Full Text Available Herbivorous slugs do significant damage to many species of crop plants. A laboratory study was conducted to determine the rate and extent of damage caused to 16 plant species by Arion vulgaris, Arion rufus, and Deroceras reticulatum. It was found, that levels of damage caused to young plants of Brassica napus, Sorghum bicolor, Vicia faba, and Sinapis alba by the slugs A. vulgaris, A. rufus, and D. reticulatum were similar, while levels of damage caused to the other studied plants by particular slug species differed significantly. Based on the results of the damage by the investigated slug species, plants were categorised as heavily or lightly damaged.

  11. Gas slug ascent in a stratified magma: Implications of flow organisation and instability for Strombolian eruption dynamics

    Science.gov (United States)

    Capponi, A.; James, M. R.; Lane, S. J.

    2016-02-01

    The canonical Strombolian paradigm of a gas slug ascending and bursting in a homogeneous low-viscosity magma cannot explain the complex details in eruptive dynamics recently revealed by field measurements and textural and geochemical analyses. Evidence points to the existence of high-viscosity magma at the top of the conduit of Strombolian-type volcanoes, acting as a plug. Here, new experiments detail the range of flow configurations that develop during the ascent and burst of a slug through rheologically stratified magma within a conduit. End-member scenarios of a tube fully filled with either high- or low-viscosity liquid bracket three main flow configurations: (1) a plug sufficiently large to fully accommodate an ascending gas slug; (2) A plug that can accommodate the intrusion of low-viscosity liquid driven by the gas expansion, but not all the slug volume, so the slug bursts with the nose in the plug whilst the base is still in the low-viscosity liquid; (3) Gas expansion is sufficient to drive the intrusion of low-viscosity liquid through the plug, with the slug bursting in the low-viscosity layer emplaced dynamically above the plug. We show that the same flow configurations are viable at volcanic-scale through a new experimentally-validated 1D model and 3D computational fluid dynamic simulations. Applied to Stromboli, our results demonstrate that the key parameters controlling the transition between each configuration are gas volume, plug thickness and plug viscosity. The flow processes identified include effective dynamic narrowing and widening of the conduit, instabilities within the falling magma film, transient partial and complete blockage of the conduit, and slug disruption. These complexities influence eruption dynamics and vigour, promoting magma mingling and resulting in pulsatory release of gas.

  12. Application of SiO_2 Nano-particles in Treatment of Raw Water Containing Anionic Surfactant%纳米SiO_2用于含表面活性剂原水的处理

    Institute of Scientific and Technical Information of China (English)

    阮彩群; 李冬梅; 任毅; 李绍秀; 李斌; 李志生

    2009-01-01

    By adding SiO_2 nano-particles into kaolin suspensions with turbidity of 6 NTU in the presence of anionic surfactant--sedium dodeeyl sulphate (SDS), dynamic coagulation experiments and quiescent settling experiments were done. The action efficiency and morphologic properties of SiO_2 nano-particles were discussed using image analysis technology and a quantitative faetor---fractal dimension. The formation and growth of flocs have fractal properties. The fractal structure formation is a main effect factor of particles coagulation, flocs compact degree and settleability. The flocs formation is interfered at the ini-tial flocculation stage in the presence of SDS. Afterwards, the mixture of SDS and the coagulant acta on particles together and enhances the flocculation efficiency. The flocs become larger and compacter, and the settleability is improved. There is competitive adsorption between SDS and SiO_2. When SiO_2 nano-particles are added alone, small and fragile flocs are formed. When PAC serves as a primary coagulant, SiO_2 nano-particles as floeeulant aid are beneficial for PAC flocs structure evolution to more compact con-figurations. The removal rates of turbidity and SDS are improved.%在含表面活性剂十二烷基硫酸钠(SDS)的低浊(6 NTU)高岭土原水中,投加纳米SiO_2进行动态混凝与静沉试验,借助图像分析技术与定量控制参数,探讨了纳米SiO_2的作用效果与形态学特性.结果表明:絮体的形成与生长具有分形特征,分形结构是影响颗粒混凝、絮团密实度与沉降特性的主要因素;SDS的存在对絮凝初期絮体的形成起阻碍作用,随后SDS与混凝剂的混合体共同对粒子作用,促进絮凝,絮体变大且密实,沉降性能改善;SDS和SiO_2对高岭土粒子存在竞争吸附;单独投加纳米SiO_2时形成的絮体小而脆弱,而以纳米SiO_2为助凝剂能促使PAC絮体结构向更密实的构型转变,对浊度和SDS的去除率提高.

  13. Molecular dynamics simulations of phase separation in the presence of surfactants

    DEFF Research Database (Denmark)

    Laradji, Mohamed; Mouritsen, Ole G.; Toxvaerd, Søren

    1994-01-01

    The dynamics of phase separation in two-dimensional binary mixtures diluted by surfactants is studied by means of molecular dynamics simulations. In contrast to pure binary systems, characterized by an algebraic time dependence of the average domain size, we find that systems containing surfactants...... exhibit nonalgebraic, slow dynamics. The average domain size eventually saturates at a value inversely proportional to the surfactant concentration. We also find that phase separation in systems with different surfactant concentrations follow a crossover scaling form. Finally, although these systems do...... not fully phase separate, we observe a dynamical scaling which is independent of the surfactant concentration. The results of these simulations are in general in agreement with previous Langevin simulations [Laradji, Guo, Grant, and Zuckermann, J. Phys. A 44, L629 (1991)] and a theory of Ostwald ripening...

  14. Solubilization of pentanol by cationic surfactants and binary mixtures of cationic surfactants

    Energy Technology Data Exchange (ETDEWEB)

    Morgan, M.E.

    1993-12-31

    The research reported here has included studies of the solubilization of pentanol in hexadecylpyridinium chloride (CPC), trimethyletetradecylammonium chloride (C{sub 14}Cl), benzyldimethyltetradecylammonium chloride (C{sub 14}BzCl), benzyldimethylhexadecylpyridinium chloride (C{sub 16}BzCl), hexadecyltrimethylammonium bromide (CTAB), and binary mixtures of CPC + C{sub 16}BzCl and C{sub 14}Cl + C{sub 14}BzCl. Rather than using calorimetric methods, this project will employ headspace chromatography to measure solubilization of pentanol over a wide range of solute concentrations. While not yielding as much thermodynamic data as calorimetry, headspace chromatography is a more direct measure of the extent of solubilization. Using headspace chromatography, is a more direct measure of the extent of solubilization. Using headspace chromatography, this study will seek to determine whether strongly synergistic mixture ratios exist in the case of binary cationic surfactant systems. There are two equilibria in the pentanol-water-surfactant system: (1) The pentanol solubilized in micelles is in equilibrium with the monomeric pentanol in solution, and (2) the monomeric pentanol is in equilibrium with the pentanol in the vapor above the solution. To establish the link between the two equilibria, a sample of the vapor above pure liquid pentanol must be collected, in order to find the activity of pentanol in solution. Also, a calibration curve for various concentrations of pentanol in solution. From this type of data it is possible to infer both the concentration of pentanol solubilized in micelles and the concentrations of pentanol in the ``bulk`` solution outside the micelles. The method is equally applicable to systems containing a single surfactant as well as mixtures of surfactants.

  15. Surfactant and metal ion effects on the mechanical properties of alginate hydrogels.

    Science.gov (United States)

    Kaygusuz, Hakan; Evingür, Gülşen Akın; Pekcan, Önder; von Klitzing, Regine; Erim, F Bedia

    2016-11-01

    This paper addresses the controlled variation of the mechanical properties of alginate gel beads by changing the alginate concentration or by adding different surfactants or cross-linking cations. Alginate beads containing nonionic Brij 35 or anionic sodium dodecyl sulfate (SDS) surfactants were prepared with two different types of cations (Ca(2+), Ba(2+)) as crosslinkers. Compression measurements were performed to investigate the effect of the surfactant and cation types and their concentrations on the Young's modulus of alginate beads. The Young's modulus was determined by using Hertz theory. For all types of alginate gel beads the Young's modulus showed an increasing value for increasing alginate contents. Addition of the anionic surfactant SDS increases the Young's modulus of the alginate beads while the addition of non-ionic surfactant Brij 35 leads to a decrease in Young's modulus. This opposite behavior is related to the contrary effect of both surfactants on the charge of the alginate beads. When Ba(2+) ions were used as crosslinker cation, the Young's modulus of the beads with the surfactant SDS was found to be approximately two times higher than the modulus of beads with the surfactant Brij 35. An ion specific effect was found for the crosslinking ability of divalent cations.

  16. Surfactant recovery from water using foam fractionation

    Energy Technology Data Exchange (ETDEWEB)

    Tharapiwattananon, N.; Osuwan, S. [Chulalongkorn Univ., Bangkok (Thailand); Scamehorn, J.F. [Inst. of Oklahoma, Norman, OK (United States)] [and others

    1996-05-01

    The purpose of this study was to investigate the use of foam fractionation to recover surfactant from water. A simple continuous mode foam fractionation was used and three surfactants were studied (two anionic and one cationic). The effects of air flow rate, foam height, liquid height, liquid feed surfactant concentration, and sparger porosity were studied. This technique was shown to be effective in either surfactant recovery or the reduction of surfactant concentration in water to acceptable levels. As an example of the effectiveness of this technique, the cetylpyridinium chloride concentration in water can be reduced by 90% in one stage with a liquid residence time of 375 minutes. The surfactant concentration in the collapsed foam is 21.5 times the feed concentration. This cationic surfactant was easier to remove from water by foam fractionation than the anionic surfactants studied.

  17. Synthesis of carbohydrate-based surfactants

    Energy Technology Data Exchange (ETDEWEB)

    Pemberton, Jeanne E.; Polt, Robin L.; Maier, Raina M.

    2016-11-22

    The present invention provides carbohydrate-based surfactants and methods for producing the same. Methods for producing carbohydrate-based surfactants include using a glycosylation promoter to link a carbohydrate or its derivative to a hydrophobic compound.

  18. In vitro surfactant structure-toxicity relationships: implications for surfactant use in sexually transmitted infection prophylaxis and contraception.

    Directory of Open Access Journals (Sweden)

    Ângela S Inácio

    Full Text Available BACKGROUND: The need for woman-controlled, cheap, safe, effective, easy-to-use and easy-to-store topical applications for prophylaxis against sexually transmitted infections (STIs makes surfactant-containing formulations an interesting option that requires a more fundamental knowledge concerning surfactant toxicology and structure-activity relationships. METHODOLOGY/PRINCIPAL FINDINGS: We report in vitro effects of surfactant concentration, exposure time and structure on the viability of mammalian cell types typically encountered in the vagina, namely, fully polarized and confluent epithelial cells, confluent but non-polarized epithelial-like cells, dendritic cells, and human sperm. Representatives of the different families of commercially available surfactants--nonionic (Triton X-100 and monolaurin, zwitterionic (DDPS, anionic (SDS, and cationic (C(nTAB (n = 10 to 16, C(12PB, and C(12BZK--were examined. Triton X-100, monolaurin, DDPS and SDS were toxic to all cell types at concentrations around their critical micelle concentration (CMC suggesting a non-selective mode of action involving cell membrane destabilization and/or destruction. All cationic surfactants were toxic at concentrations far below their CMC and showed significant differences in their toxicity toward polarized as compared with non-polarized cells. Their toxicity was also dependent on the chemical nature of the polar head group. Our results suggest an intracellular locus of action for cationic surfactants and show that their structure-activity relationships could be profitably exploited for STI prophylaxis in vaginal gel formulations. The therapeutic indices comparing polarized epithelial cell toxicity to sperm toxicity for all surfactants examined, except C(12PB and C(12BZK, does not justify their use as contraceptive agents. C(12PB and C(12BZK are shown to have a narrow therapeutic index recommending caution in their use in contraceptive formulations. CONCLUSIONS

  19. Effects of Concentration and Conformation of Surfactants on Phase Separation of Surfactant-Water-Oil Systems

    Institute of Scientific and Technical Information of China (English)

    袁银权; 邹宪武; 刘昊阳

    2004-01-01

    The effects of surfactants on the phase separation of surfactant-water-oil systems have been investigated by using discontinuous molecular dynamic simulations. The phase separation speed and equilibrium configuration are dependent on the surfactant concentration and conformation. The equilibrium concentration of surfactants at the interface remains constant. With the increasing surfactant concentration, the equilibrium configuration crosses over from the disperse phase to the bicontinuous one. The crossover concentration is estimated. The conformation of the surfactant has little effect on the equilibrium concentration of surfactants at the interface,while it affects the equilibrium configuration after phase separation.

  20. Complex Formation Between Polyelectrolytes and Ionic Surfactants

    OpenAIRE

    1998-01-01

    The interaction between polyelectrolyte and ionic surfactant is of great importance in different areas of chemistry and biology. In this paper we present a theory of polyelectrolyte ionic-surfactant solutions. The new theory successfully explains the cooperative transition observed experimentally, in which the condensed counterions are replaced by ionic-surfactants. The transition is found to occur at surfactant densities much lower than those for a similar transition in non-ionic polymer-sur...

  1. MULTIPHASE DROPLET/SLUG BREAK-UP MECHANISM IN MICROFLUIDIC T-JUNCTIONS AT VARIOUS WEBER NUMBERS

    Directory of Open Access Journals (Sweden)

    Wan Leng (Dawn Leow

    2011-10-01

    Full Text Available Normal 0 false false false EN-MY X-NONE X-NONE The formation of immiscible liquid droplets, or slugs, in microchannels features the advantages of volume control and mixing enhancement over single-phase microflows. Although the applications of droplet-based microfluidics have been widely demonstrated, the fundamental physics governing droplet break-up remains an area of active research. This study defines an effective Weber (Weeff number that characterizes the interplay of interfacial tension, shear stress and channel pressure drop in driving slug formation in T-junction microchannel for a relative range of low, intermediate and high flow rates. The immiscible fluid system in this study consists of Tetradecane slug formation in Acetonitrile. The progressive deformation of slug interfaces during break-up events is observed. Experimental results indicate that, at a relatively low Weeff, clean slug break-up occurs at the intersection of the side and main channels. At intermediate Weeff, the connecting neck of the dispersed phase is stretched to a short and thin trail of laminar flow prior to breaking up a short distance downstream of the T-junction. At a relatively high Weeff, the connecting neck develops into a longer and thicker trail of laminar flow that breaks up further downstream of the main channel.

  2. Binding of cationic surfactants to humic substances

    NARCIS (Netherlands)

    Ishiguro, M.; Tan, W.; Koopal, L.K.

    2007-01-01

    Commercial surfactants are introduced into the environment either through waste products or site-specific contamination. The amphiphilic nature of both surfactants and humic substances (HS) leads to their mutual attraction especially when surfactant and HS are oppositely charged. Binding of the cati

  3. Surfactant adsorption to soil components and soils

    NARCIS (Netherlands)

    Ishiguro, Munehide; Koopal, Luuk K.

    2016-01-01

    Soils are complex and widely varying mixtures of organic matter and inorganic materials; adsorption of surfactants to soils is therefore related to the soil composition. We first discuss the properties of surfactants, including the critical micelle concentration (CMC) and surfactant adsorption on

  4. Effects of permeability heterogeneity on the performance of surfactant-enhanced remediation

    Energy Technology Data Exchange (ETDEWEB)

    Lee, K.S. [Kyonggi Univ., Seoul (Korea, Republic of)

    2010-07-01

    The subsurface contamination by nonaqueous phase liquids (NAPLs) is a complicated process and difficult to treat because these organic contaminants tend to adsorb onto the soil matrix. They have low water solubility and a limited rate of mass transfer for biodegradation. NAPLs may leach from the soil for a longer period of time and may eventually become a long-term continuous contamination source of the soil and groundwater. One method to enhance pump-and-treat aquifer remediation performance involves surfactant-enhanced aquifer remediation (SEAR). Because their success depends on the delivery of injected chemical and water into the subsurface to contact the organic liquids, geologic heterogeneities are likely the main factors which reduce the effectiveness of SEAR processes. This paper presented a study that involved numerical simulations to assess the effect of spatial variability of aquifer permeability on NAPL recovery and injection pressure as well as spatial and temporal distributions of NAPLs during the remediation process. The paper outlined the mathematical backgrounds, numerical model, and results and discussion. It was concluded the effectiveness of SEAR is sensitive to injection time due to dispersion of surfactant slug with the presence of a higher degree of heterogeneity. 6 refs., 3 figs.

  5. Polymer gels with associating side chains and their interaction with surfactants

    Science.gov (United States)

    Gordievskaya, Yulia D.; Rumyantsev, Artem M.; Kramarenko, Elena Yu.

    2016-05-01

    Conformational behaviour of hydrophobically modified (HM) polymer gels in solutions of nonionic surfactants is studied theoretically. A HM gel contains hydrophobic side chains (stickers) grafted to its subchains. Hydrophobic stickers are capable to aggregate into joint micelles with surfactant molecules. Micelles containing more than one sticker serve as additional physical cross-links of the network, and their formation causes gel shrinking. In the proposed theoretical model, the interior of the gel/surfactant complex is treated as an array of densely packed spherical polymer brushes consisting of gel subchains tethered to the surface of the spherical sticker/surfactant micelles. Effect of stickers length and grafting density, surfactant concentration and hydrophobicity on gel swelling as well as on hydrophobic association inside it is analyzed. It is shown that increasing surfactant concentration can result in a gel collapse, which is caused by surfactant-induced hydrophobic aggregation of stickers, and a successive gel reswelling. The latter should be attributed to a growing fraction of surfactants in joint aggregates and, hence, increasing number of micelles containing only one sticker and not participating in gel physical cross-linking. In polyelectrolyte (PE) gels hydrophobic aggregation is opposed by osmotic pressure of mobile counterions, so that at some critical ionization degree hydrophobic association is completely suppressed. Hydrophobic modification of polymers is shown to open new ways for controlling gel responsiveness. In particular, it is discussed that incorporation of photosensitive groups into gel subchains and/or surfactant tail could give a possibility to vary the gel volume by light. Since hydrophobic aggregation regularities in gels and solutions are common, we hope our findings will be useful for design of polymer based self-healing materials as well.

  6. Fabrication of U-10wt.%Zr Fuel slug for SFR by Injection Casting

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jong Hwan; Song, Hoon; Kim, Hyung Tae; Ko, Young Mo; Kim, Ki Hwan; Lee, Chan B. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2013-10-15

    The fabrication technology of metal fuel has been developed by various methods such as rolling, swaging, wire drawing, and co-extrusion, but each of these methods had process limitations requiring an additional subsequent process, and needing the fabrication equipment is complex, which is not favorable for remote use. A practical process of metallic fuel fabrication for an SFR needs to be cost efficient, suitable for remote operation, and capable of mass production while reducing the amount of radioactive waste. Injection casting was chosen as the most promising technique, in the early 1950s, and this technique has been applied to fuel slug fabrication for the Experimental Breeder Reactor-II (EBR-II) driver and the Fast Flux Test Facility (FFTF) fuel pins. Because of the simplistic nature of the process and equipment, compared to other processes examined, this process has been successfully used in a remote operation environment for fueling of the EBR-II reactor. In this study, vacuum injection casting suitable for remote operation has been developed to fabricate metallic fuel for an SFR. Vacuum injection casting technique was developed to fabricate metallic fuel for an SFR. The appearance of the fabricated U-10wt.%Zr fuel was generally sound and the internal integrity was found to be satisfactory through gamma-ray radiography. Minimum fuel losses after casting relative to the initial charge amount of U-10wt.%Zr fuel slugs met the proposed goal of less than 0.1% fuel losses during fabrication. Modifications of the current facility system and advanced casting techniques are underway to produce higher quality fuel slugs.

  7. Model-Free Predictive Anti-Slug Control of a Well-Pipeline-Riser

    Directory of Open Access Journals (Sweden)

    Christer Dalen

    2016-01-01

    Full Text Available Simplified linearized discrete time dynamic state space models are developed for a 3-phase well-pipeline-riser and tested together with a high fidelity dynamic model built in K-Spice and LedaFlow. In addition the Meglio pipeline-riser model is used as an example process. These models are developed from a subspace algorithm, i.e. Deterministic and Stochastic system identification and Realization (DSR, and implemented in a Model Predictive Controller (MPC for stabilizing the slugging regime. The MPC, LQR and PI control strategies are tested.

  8. Directed percolation describes lifetime and growth of turbulent puffs and slugs

    CERN Document Server

    Sipos, Maksim

    2011-01-01

    The phenomenology of pipe flow is characterized by complex turbulent structures, puffs and slugs, whose behavior is still not fully understood. In this Letter, we show that transitional turbulence in a pipe can be quantitatively modeled by directed percolation (DP). The active (turbulent) states in subcritical DP exhibit superexponentially diverging characteristic lifetime, similar to that observed of turbulent puffs. Above the percolation threshold, active (turbulent) clusters expand into the inactive (laminar) phase with a well-defined velocity whose scaling with control parameter (Reynolds number or percolation probability) is consistent with experimental results.

  9. The slug mucosal irritation (SMI) assay: development of a screening tool for the evaluation of ocular discomfort caused by shampoos.

    Science.gov (United States)

    Lenoir, Joke; Claerhout, Ilse; Kestelyn, Philippe; Klomp, Andre; Remon, Jean-Paul; Adriaens, Els

    2011-12-01

    In this research, the slug mucosal irritation (SMI) assay was applied to predict ocular discomfort caused by shampoos to investigate the correlation between responses in slugs and humans. Several SMI experiments and a human eye irritation test (HEIT) were performed with 1 artificial tear solution (ArtTear) and 5 shampoos (A-E; 5%-dilution). In the HEIT, evaluation was performed by participants and an ophthalmologist at several time points. Analyses reveal that (1) a significant positive association existed between immediate stinging reaction reported by the participants and the mean total mucus produced by the slugs (MTMP) (Spearman's Rank correlation=0.986, pSMI assay is a promising evaluation method for discomfort in the human eye. Screening prototype (eye) formulations with this assay allows formula optimization prior to a HEIT.

  10. Drift flux model as approximation of two fluid model for two phase dispersed and slug flow in tube

    Energy Technology Data Exchange (ETDEWEB)

    Nigmatulin, R.I.

    1995-09-01

    The analysis of one-dimensional schematizing for non-steady two-phase dispersed and slug flow in tube is presented. Quasi-static approximation, when inertia forces because of the accelerations of the phases may be neglected, is considered. Gas-liquid bubbly and slug vertical upward flows are analyzed. Non-trivial theoretical equations for slip velocity for these flows are derived. Juxtaposition of the derived equations for slip velocity with the famous Zuber-Findlay correlation as cross correlation coefficients is criticized. The generalization of non-steady drift flux Wallis theory taking into account influence of wall friction on the bubbly or slug flows for kinematical waves is considered.

  11. A PHYSICAL MODEL FOR PREDICTING THE PRESSURE DROP OF GAS-LIQUID SLUG FLOW IN HORIZONTAL PIPES

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    A comprehensive treatment of all sources of pressure drop within intermittent gas-liquid flow is presented. A slug unit is divided into three parts and the pressure gradient of each part is calculated separately. In the mixing zone the momentum theory is employed and the mixing process between the film and slug is simulated by a two-dimensional wall jet entering a large reservoir to calculate the mixing length. The boundary layer theory is utilized to calculate the pressure drop for the slug body and the momentum equation of the film zone is integrated to calculate the pressure drop for the film zone. The pressure drop predicted in present model is in good agreement with all the measurements.

  12. Determination of alkylbenzenesulfonate surfactants in groundwater using macroreticular resins and carbon-13 nuclear magnetic resonance spectrometry

    Science.gov (United States)

    Thurman, E.M.; Willoughby, T.; Barber, L.B.; Thorn, K.A.

    1987-01-01

    Alkylbenzenesulfonate surfactants were determined in groundwater at concentrations as low as 0.3 mg/L. The method uses XAD-8 resin for concentration, followed by elution with methanol, separation of anionic and nonionic surfactants by anion exchange, quantitation by titration, and identification by 13C nuclear magnetic resonance spectrometry. Laboratory standards and field samples containing straight-chain and branched-chain alkylbenzenesulfonates, sodium dodecyl sulfate, and alkylbenzene ethoxylates were studied. The XAD-8 extraction of surfactants from groundwater was completed in the field, which simplified sample preservation and reduced the cost of transporting samples.

  13. Production and characterisation of recombinant forms of human pulmonary surfactant protein C (SP-C)

    DEFF Research Database (Denmark)

    Lukovic, Dunja; Plasencia, Inés; Taberner, Francisco J

    2006-01-01

    Surfactant protein C (SP-C) is an essential component for the surface tension-lowering activity of the pulmonary surfactant system. It contains a valine-rich alpha helix that spans the lipid bilayer, and is one of the most hydrophobic proteins known so far. SP-C is also an essential component...... of various surfactant preparations of animal origin currently used to treat neonatal respiratory distress syndrome (NRDS) in preterm infants. The limited supply of this material and the risk of transmission of infectious agents and immunological reactions have prompted the development of synthetic SP...

  14. Desorption of organophosphorous pesticides from soil with wastewater and surfactant solutions

    Energy Technology Data Exchange (ETDEWEB)

    Hernandez-Soriano, M. C.; Mingorance, M. D.; Pena, A.

    2009-07-01

    Surfactants can be introduced in the environment by wastewater discharge, point-charge pollution or deliberate action, e. g. to remediate contaminated soil or groundwater. The irrigation of soil with wastewater containing surfactants may modify pesticide desorption from soil, thus affecting their affecting their environmental fate. Desorption from soil of the plain of Granada (South-eastern Spain) of two organophosphorous pesticides, diazinon and dimethoate, differing in solubility and hydrophobicity, has been evaluated in the presence of different surfactant aqueous solutions and municipal wastewater. (Author)

  15. Nanofiltration: ion exchange system for effective surfactant removal from water solutions

    Directory of Open Access Journals (Sweden)

    I. Kowalska

    2014-12-01

    Full Text Available A system combining nanofiltration and ion exchange for highly effective separation of anionic surfactant from water solutions was proposed. The subjects of the study were nanofiltration polyethersulfone membranes and ion-exchange resins differing in type and structure. The quality of the treated solution was affected by numerous parameters, such as quality of the feed solution, membrane cut-off, resin type, dose and the solution contact time with the resin. A properly designed purification system made it possible to reduce the concentration of anionic surfactant below 1 mg L-1 from feed solutions containing surfactant in concentrations above the CMC value.

  16. Glicerólise de óleo de peixe catalisada por lipase comercial de Rhizomucor miehei em meio com surfactante de grau alimentício Glycerolysis of fish oil catalyzed by a commercial lipase from Rhizomucor miehei in reaction media containing food grade surfactant

    Directory of Open Access Journals (Sweden)

    Joanna Silva Santos

    2013-01-01

    Full Text Available Omega-3 enriched partial acylglycerols are beneficial for human health. The aim of this study was to obtain monoacylglycerols (MAG and diacylglycerols (DAG by means of glycerolysis of fish oil catalyzed by a lipase from Rhizomucor miehei in the presence of food grade surfactants (Tween 65, 80 or 85. Glycerolysis was successful in the reaction media for all the tested surfactants, showing their potential for use as additives in such a system. The best results, however, were obtained for the reaction medium in the absence of surfactant whose peroxide value was the lowest after glycerolysis.

  17. Applicability of the black slug Arion ater for monitoring exposure to polycyclic aromatic hydrocarbons and their subsequent bioactivation into DNA binding metabolites

    NARCIS (Netherlands)

    Hamers, T.; Kalis, E.J.J.; Berg, van den J.H.J.; Maas, L.M.; Schooten, van F.J.; Murk, A.J.

    2004-01-01

    The applicability of terrestrial black slugs Arion ater (Mollusca, Gastropoda) was studied for biomonitoring environmental exposure to polycyclic aromatic hydrocarbons (PAHs). In laboratory experiments, slugs were orally exposed to benzo[a]pyrene (BaP) for a short term (3 days) or a long term (119

  18. Applicability of the black slug Arion ater for monitoring exposure to polycyclic aromatic hydrocarbons and their subsequent bioactivation into DNA binding metabolites

    NARCIS (Netherlands)

    Hamers, T.; Kalis, E.J.J.; Berg, van den J.H.J.; Maas, L.M.; Schooten, van F.J.; Murk, A.J.

    2004-01-01

    The applicability of terrestrial black slugs Arion ater (Mollusca, Gastropoda) was studied for biomonitoring environmental exposure to polycyclic aromatic hydrocarbons (PAHs). In laboratory experiments, slugs were orally exposed to benzo[a]pyrene (BaP) for a short term (3 days) or a long term (119 d

  19. Physical properties of botanical surfactants.

    Science.gov (United States)

    Müller, Lillian Espíndola; Schiedeck, Gustavo

    2017-08-24

    Some vegetal species have saponins in their composition with great potential to be used as natural surfactants in organic crops. This work aims to evaluate some surfactants physical properties of Quillaja brasiliensis and Agave angustifolia, based on different methods of preparation and concentration. The vegetal samples were prepared by drying and grinding, frozen and after chopped or used fresh and chopped. The neutral bar soap was used as a positive control. The drying and grinding of samples were the preparation method that resulted in higher foam column height in both species but Q. brasiliensis was superior to A. angustifolia in all comparisons and foam index was 2756 and 1017 respectively. Critical micelle concentration of Q. brasiliensis was 0.39% with the superficial tension of 54.40mNm(-1) while neutral bar soap was 0.15% with 34.96mNm(-1). Aspects such as genetic characteristics of the species, environmental conditions, and analytical methods make it difficult to compare the results with other studies, but Q. brasiliensis powder has potential to be explored as a natural surfactant in organic farming. Not only the surfactants physical properties of botanical saponins should be taken into account but also its effect on insects and diseases control when decided using them. Copyright © 2017 Elsevier B.V. All rights reserved.

  20. Interactions of Ovalbumin with Ionic Surfactants

    Institute of Scientific and Technical Information of China (English)

    GUO Xia; YAN Hui; GUO Rong

    2008-01-01

    The interactions of ovalbumin (OVA) with one anionic surfactant,sodium dodecyl sulfate (SDS),and two cationic surfactants,dodecyl trimethylammonium bromide (DTAB) and cetyl trimethylammonium bromide (CTAB),in water have been studied through fluorescence and UV-Vis spectroscopies and transmission electronic microscopy,combined with the measurement of conductivity.OVA can increase the critical micelle concentrations (cmc) of SDS and CTAB but has little effect on that of DTAB.The interaction between surfactant monomer and OVA is greater than that between surfactant micelles and OVA.Moreover,SDS can make OVA unfolded while cationic surfactants cannot.

  1. Surfactant gene polymorphisms and interstitial lung diseases

    Directory of Open Access Journals (Sweden)

    Pantelidis Panagiotis

    2001-11-01

    Full Text Available Abstract Pulmonary surfactant is a complex mixture of phospholipids and proteins, which is present in the alveolar lining fluid and is essential for normal lung function. Alterations in surfactant composition have been reported in several interstitial lung diseases (ILDs. Furthermore, a mutation in the surfactant protein C gene that results in complete absence of the protein has been shown to be associated with familial ILD. The role of surfactant in lung disease is therefore drawing increasing attention following the elucidation of the genetic basis underlying its surface expression and the proof of surfactant abnormalities in ILD.

  2. Pellino-1 promotes lung carcinogenesis via the stabilization of Slug and Snail through K63-mediated polyubiquitination

    Science.gov (United States)

    Jeon, Yoon Kyung; Kim, Chung Kwon; Hwang, Kyung Rim; Park, Hye-Young; Koh, Jaemoon; Chung, Doo Hyun; Lee, Chang-Woo; Ha, Geun-Hyoung

    2017-01-01

    Pellino-1 is an E3 ubiquitin ligase acting as a critical mediator for a variety of immune receptor signaling pathways, including Toll-like receptors, interleukin-1 receptor and T-cell receptors. We recently showed that the Pellino-1-transgenic (Tg) mice developed multiple tumors with different subtypes in hematolymphoid and solid organs. However, the molecular mechanism underlying the oncogenic role of Pellino-1 in solid tumors remains unknown. Pellino-1-Tg mice developed adenocarcinoma in the lungs, and Pellino-1 expression was higher in human lung adenocarcinoma cell lines compared with non-neoplastic bronchial epithelial cell lines. Pellino-1 overexpression increased the cell proliferation, survival, colony formation, invasion and migration of lung adenocarcinoma cells, whereas Pellino-1 knock-down showed the opposite effect. Pellino-1 overexpression activated PI3K/Akt and ERK signaling pathways and elicited an epithelial–mesenchymal transition (EMT) phenotype of lung adenocarcinoma cells. Pellino-1-mediated EMT was demonstrated through morphology, the upregulation of Vimentin, Slug and Snail expression and the downregulation of E-cadherin and β-catenin expression. Notably, Pellino-1 had a direct effect on the overexpression of Snail and Slug through Lys63-mediated polyubiquitination and the subsequent stabilization of these proteins. Pellino-1 expression level was significantly correlated with Snail and Slug expression in human lung adenocarcinoma tissues, and lung tumors from Pellino-1-Tg mice showed Snail and Slug overexpression. The Pellino-1-mediated increase in the migration of lung adenocarcinoma cells was mediated by Snail and Slug expression. Taken together, these results show that Pellino-1 contributes to lung tumorigenesis by inducing overexpression of Snail and Slug and promoting EMT. Pellino-1 might be a potential therapeutic target for lung cancer. PMID:28009353

  3. Integrated Proteomics and Genomics Analysis Reveals a Novel Mesenchymal to Epithelial Reverting Transition in Leiomyosarcoma through Regulation of Slug*

    Science.gov (United States)

    Yang, Jilong; Eddy, James A.; Pan, Yuan; Hategan, Andrea; Tabus, Ioan; Wang, Yingmei; Cogdell, David; Price, Nathan D.; Pollock, Raphael E.; Lazar, Alexander J. F.; Hunt, Kelly K.; Trent, Jonathan C.; Zhang, Wei

    2010-01-01

    Leiomyosarcoma is one of the most common mesenchymal tumors. Proteomics profiling analysis by reverse-phase protein lysate array surprisingly revealed that expression of the epithelial marker E-cadherin (encoded by CDH1) was significantly elevated in a subset of leiomyosarcomas. In contrast, E-cadherin was rarely expressed in the gastrointestinal stromal tumors, another major mesenchymal tumor type. We further sought to 1) validate this finding, 2) determine whether there is a mesenchymal to epithelial reverting transition (MErT) in leiomyosarcoma, and if so 3) elucidate the regulatory mechanism responsible for this MErT. Our data showed that the epithelial cell markers E-cadherin, epithelial membrane antigen, cytokeratin AE1/AE3, and pan-cytokeratin were often detected immunohistochemically in leiomyosarcoma tumor cells on tissue microarray. Interestingly, the E-cadherin protein expression was correlated with better survival in leiomyosarcoma patients. Whole genome microarray was used for transcriptomics analysis, and the epithelial gene expression signature was also associated with better survival. Bioinformatics analysis of transcriptome data showed an inverse correlation between E-cadherin and E-cadherin repressor Slug (SNAI2) expression in leiomyosarcoma, and this inverse correlation was validated on tissue microarray by immunohistochemical staining of E-cadherin and Slug. Knockdown of Slug expression in SK-LMS-1 leiomyosarcoma cells by siRNA significantly increased E-cadherin; decreased the mesenchymal markers vimentin and N-cadherin (encoded by CDH2); and significantly decreased cell proliferation, invasion, and migration. An increase in Slug expression by pCMV6-XL5-Slug transfection decreased E-cadherin and increased vimentin and N-cadherin. Thus, MErT, which is mediated through regulation of Slug, is a clinically significant phenotype in leiomyosarcoma. PMID:20651304

  4. COUPLING THE ALKALINE-SURFACTANT-POLYMER TECHNOLOGY AND THE GELATION TECHNOLOGY TO MAXIMIZE OIL PRODUCTION

    Energy Technology Data Exchange (ETDEWEB)

    Malcolm Pitts; Jie Qui; Dan Wilson; Phil Dowling

    2004-05-01

    Gelation technologies have been developed to provide more efficient vertical sweep efficiencies for flooding naturally fractured oil reservoirs or more efficient areal sweep efficiency those with high permeability contrast ''thief zones''. The field proven alkaline-surfactant-polymer technology economically recovers 15% to 25% OOIP more oil than waterflooding in the swept pore space of an oil reservoir. However, alkaline-surfactant-polymer technology is not amenable to the naturally fractured reservoirs or those with thief zones because much of the injected solution bypasses the target pore space containing oil. The objective of this work is to investigate whether combining these two technologies could broaden the applicability of alkaline-surfactant-polymer flooding into these reservoirs. Fluid-fluid interaction with different gel chemical compositions and alkaline-surfactant-polymer solution with pH values ranging from 9.2 to 12.9 have been tested. Aluminum-polyacrylamide gels are not stable to alkaline-surfactant-polymer solutions at any pH. Chromium--polyacrylamide gels with polymer to chromium ion ratios of 25 or greater were stable to alkaline-surfactant-polymer solutions if solution pH was 10.6 or less. When the polymer to chromium ion was 15 or less, chromium-polyacrylamide gels were stable to alkaline-surfactant-polymer solutions with pH values up to 12.9. Chromium-xanthan gum gels were stable to alkaline-surfactant-polymer solutions with pH values of 12.9 at the polymer to chromium ion ratios tested. Silicate-polyacrylamide, resorcinol-formaldehyde, and sulfomethylated resorcinol-formaldehyde gels were also stable to alkaline-surfactant-polymer solutions with pH values ranging from 9.2 to 12.9. Iron-polyacrylamide gels were immediately destroyed when contacted with any of the alkaline-surfactant-polymer solutions with pH values of 9.2 to 12.9.

  5. Physicochemistry and percolation behavior of microemulsions as a function of chain length of cosurfactant and surfactant

    Directory of Open Access Journals (Sweden)

    Purva Thatai

    2015-03-01

    Full Text Available The study involved investigations on phase behavior and physicochemical characterization of microemulsions (MEs stabilized by mixture containing polysorbates (C12-C18 as surfactants and n-alkanols (C2-C6 as cosurfactant. Distribution coefficient and Gibbs free energy were also determined for systems containing Tween 20 as surfactant. ME having Tween 20 as surfactant and ethanol as cosurfactant was found to exhibit maximium ME region as well as water solubilization capacity (WSC. Values of both these parameters were found to decrease as chain length of surfactant increased in all cases of alkanols with exception of Tween 80. This could be attributed to unsaturated structure of Tween 80 which presumably caused folding of chain and lesser oil penetration. Furthermore, the transition of w/o MEs to o/w MEs via bicontinuous structure along the dilution line was confirmed by conductivity, viscosity and droplet size analysis.

  6. An anionic surfactant for EOR applications

    Science.gov (United States)

    Sagir, Muhammad; Tan, Isa M.; Mushtaq, Muhammad

    2014-10-01

    This work is to investigate the new anionic surfactants for the Enhanced Oil Recovery (EOR) application. Sulfonated anionic surfactant was produced by attaching SO3 to an ethoxylated alcohol to increase the performance of the surfactant. Methallyl chloride and ethoxylated alcohol was reacted followed by the reaction with sodium bisulfite to produce anionic sulfonated surfactant in 80.3 % yield. The sulfonation reaction parameters such as reactants mole ratio, reaction temperature and catalyst amount were optimized. The generation and stability of foam from the synthesized surfactant is also tested and results are reported. The synthesized novel surfactant was further investigated for the effect on the CO2 mobility in porous media and the findings are presented here. This in house developed surfactant has a great potential for CO2- EOR applications.

  7. Snail and Slug, key regulators of TGF-β-induced EMT, are sufficient for the induction of single-cell invasion.

    Science.gov (United States)

    Naber, Hildegonda P H; Drabsch, Yvette; Snaar-Jagalska, B Ewa; ten Dijke, Peter; van Laar, Theo

    2013-05-24

    TGF-β plays a dual role in cancer; in early stages it inhibits tumor growth, whereas later it promotes invasion and metastasis. TGF-β is thought to be pro-invasive by inducing epithelial-to-mesenchymal transition (EMT) via induction of transcriptional repressors, including Slug and Snail. In this study, we investigated the role of Snail and Slug in TGF-β-induced invasion in an in vitro invasion assay and in an embryonic zebrafish xenograft model. Ectopic expression of Slug or Snail promoted invasion of single, rounded amoeboid cells in vitro. In an embryonic zebrafish xenograft model, forced expression of Slug and Snail promoted single cell invasion and metastasis. Slug and Snail are sufficient for the induction of single-cell invasion in an in vitro invasion assay and in an embryonic zebrafish xenograft model. Copyright © 2013 Elsevier Inc. All rights reserved.

  8. Snail and Slug collaborate on EMT and tumor metastasis through miR-101-mediated EZH2 axis in oral tongue squamous cell carcinoma.

    Science.gov (United States)

    Zheng, Min; Jiang, Ya-ping; Chen, Wei; Li, Kai-de; Liu, Xin; Gao, Shi-yu; Feng, Hao; Wang, Sha-sha; Jiang, Jian; Ma, Xiang-rui; Cen, Xiao; Tang, Ya-jie; Chen, Yu; Lin, Yun-feng; Tang, Ya-ling; Liang, Xin-hua

    2015-03-30

    microRNAs(miRNAs) can regulate epithelial-mesenchymal transition (EMT) through transcription factors, however, little is known whether EMT transcription factors can modulate miRNAs and further induce EMT and cancer metastasis. Here we show that overexpression of Snail and Slug leads to a mesenchymal phenotype and morphology and enhances cell invasion along with stem cell properties in squamous cell carcinoma of oral tongue (OTSCC) cells. Repression of miR-101 expression by Snail and Slug is essential for Snail/Slug-induced malignant phenotypes. The suppression of miR-101 subsequently activates EZH2, the sole histone methyltransferase, inducing EMT, migration and invasion of OTSCC cells. Importantly, co-overexpression of Slug and Snail correlates with poor survival and elevated EZH2 expression in two independent patient cohorts of OTSCC specimens. These findings defined a Snail and Slug/miR-101/EZH2 pathway as a novel regulatory axis of EMT-mediated-microRNA signaling.

  9. Effects of Surfactant Contamination on the Next Generation Gas Trap for the ISS Internal Thermal Control System

    Science.gov (United States)

    Leimkuehler, Thomas O.; Lukens, Clark; Reeves, Daniel R.; Holt, James M.

    2004-01-01

    The current dual-membrane gas trap is designed to remove non-condensed gas bubbles from the Internal Thermal Control System (ITCS) coolant on board the International Space Station (ISS). To date it has successfully served its purpose of preventing gas bubbles from causing depriming, overspeed, and shutdown of the ITCS pump. However, contamination in the ITCS coolant has adversely affected the gas venting rate and lifetime of the gas trap, warranting a development effort for a next-generation gas trap. Previous testing has shown that a hydrophobic-only design is capable of performing even better than the current dual-membrane design for both steady-state gas removal and gas slug removal in clean deionized water. This paper presents results of testing to evaluate the effects of surfactant contamination on the steady-state performance of the hydrophobic-only design.

  10. Desorption of organo phosphorous pesticides from soil with wastewater and surfactant solution

    OpenAIRE

    Hernandez-Soriano, Maria del Carmen; Mingorance, Maria Dolores; Peña, Aranzazu

    2008-01-01

    Surfactants can be introduced in the environment by wastewater discharge, point-charge pollution or deliberate action, e.g. to remediate contaminated soil or groundwater. The irrigation of soil with wastewater containing surfactants may modify pesticide desorption from soil, thus affecting their environmental fate. Desorption from soil of the plain of Granada (South-eastern Spain) of two organophosphorous pesticides, diazinon and dimethoate, differing in solubility and hydrophobicity...

  11. CFD Analysis of a Slug Mixing Experiment Conducted on a VVER-1000 Model

    Directory of Open Access Journals (Sweden)

    F. Moretti

    2009-01-01

    Full Text Available A commercial CFD code was applied, for validation purposes, to the simulation of a slug mixing experiment carried out at OKB “Gidropress” scaled facility in the framework of EC TACIS project R2.02/02: “Development of safety analysis capabilities for VVER-1000 transients involving spatial variations of coolant properties (temperature or boron concentration at core inlet.” Such experimental model reproduces a VVER-1000 nuclear reactor and is aimed at investigating the in-vessel mixing phenomena. The addressed experiment involves the start-up of one of the four reactor coolant pumps (the other three remaining idle, and the presence of a tracer slug on the starting loop, which is thus transported to the reactor pressure vessel where it mixes with the clear water. Such conditions may occur in a boron dilution scenario, hence the relevance of the addressed phenomena for nuclear reactor safety. Both a pretest and a posttest CFD simulations of the mentioned experiment were performed, which differ in the definition of the boundary conditions (based either on nominal quantities or on measured quantities, resp.. The numerical results are qualitatively and quantitatively analyzed and compared against the measured data in terms of space and time tracer distribution at the core inlet. The improvement of the results due to the optimization of the boundary conditions is evidenced, and a quantification of the simulation accuracy is proposed.

  12. A Review of the Multilevel Slug Test for Characterizing Aquifer Heterogeneity

    Directory of Open Access Journals (Sweden)

    Chia-Shyun Chen

    2012-01-01

    Full Text Available All aquifers are heterogeneous to a certain degree. The spatial distribution of hydraulic conductivity K(x, y, z, or aquifer heterogeneity, significantly influences the groundwater flow movement and associated solute transport. Of particular importance in designing an in-situ remediation plan is a knowledge of low-K layers because they are less accessible to remedial agents and form a bottleneck in remediation. The characterization of aquifer heterogeneity is essential to the solution of many practical and scientific groundwater problems. This article reviews the field technique using the multilevel slug test (MLST, which determines a series of K estimates at depths of interest in a well by making use of a double-packer system. The K(z obtained manifests the vertical variation of hydraulic conductivity in the vicinity of the test well, and the combination of K(z from different wells gives rise to a three-dimensional description of K(x, y, z. The MLST response is rather sensitive to hydraulic conductivity variation; e.g., it is oscillatory for highly permeable conditions (K > 5 × 10-4 m s-1 and a nonoscillatory for K < 5 × 10-4 m s-1. In this article we discuss the instrumentation of the double-packer system, the implementation of the depth-specific slug test, the data analysis methods for a spectrum of response characteristics usually observed in the field, and field applications of the MLST.

  13. Wire-mesh and ultrasound techniques applied for the characterization of gas-liquid slug flow

    Energy Technology Data Exchange (ETDEWEB)

    Ofuchi, Cesar Y.; Sieczkowski, Wytila Chagas; Neves Junior, Flavio; Arruda, Lucia V.R.; Morales, Rigoberto E.M.; Amaral, Carlos E.F.; Silva, Marco J. da [Federal University of Technology of Parana, Curitiba, PR (Brazil)], e-mails: ofuchi@utfpr.edu.br, wytila@utfpr.edu.br, neves@utfpr.edu.br, lvrarruda@utfpr.edu.br, rmorales@utfpr.edu.br, camaral@utfpr.edu.br, mdasilva@utfpr.edu.br

    2010-07-01

    Gas-liquid two-phase flows are found in a broad range of industrial applications, such as chemical, petrochemical and nuclear industries and quite often determine the efficiency and safety of process and plants. Several experimental techniques have been proposed and applied to measure and quantify two-phase flows so far. In this experimental study the wire-mesh sensor and an ultrasound technique are used and comparatively evaluated to study two-phase slug flows in horizontal pipes. The wire-mesh is an imaging technique and thus appropriated for scientific studies while ultrasound-based technique is robust and non-intrusive and hence well suited for industrial applications. Based on the measured raw data it is possible to extract some specific slug flow parameters of interest such as mean void fraction and characteristic frequency. The experiments were performed in the Thermal Sciences Laboratory (LACIT) at UTFPR, Brazil, in which an experimental two-phase flow loop is available. The experimental flow loop comprises a horizontal acrylic pipe of 26 mm diameter and 9 m length. Water and air were used to produce the two phase flow under controlled conditions. The results show good agreement between the techniques. (author)

  14. Chondrogenic potential of human mesenchymal stem cells and expression of Slug transcription factor.

    Science.gov (United States)

    Brini, Anna T; Niada, Stefania; Lambertini, Elisabetta; Torreggiani, Elena; Arrigoni, Elena; Lisignoli, Gina; Piva, Roberta

    2015-06-01

    The scientific literature rarely reports experimental failures or inconsistent outcomes in the induction of cell differentiation; however, researchers commonly experience poor or unsuccessful responses to differentiating agents when culturing stem cells. One way of investigating the underlying reasons for such responses is to look at the basal expression levels of specific genes in multipotent stem cells before the induction of differentiation. In addition to shedding light on the complex properties of stem cells and the molecular modulation of differentiation pathways, this strategy can also lead to the development of important time- and money-saving tools that aid the efficient selection of cellular specimens--in this case, stem cells that are more prone to differentiate towards specific lineages and are therefore more suitable for cell-based therapeutic protocols in regenerative medicine. To address this latter aspect, this study focused on understanding the reasons why some human mesenchymal stem cell (hMSC) samples are less efficient at differentiating towards chondrogenesis. This study shows that analysis of the basal expression levels of Slug, a negative regulator of chondrogenesis in hMSC, provides a rapid and simple tool for distinguishing stem cell samples with the potential to form a cartilage-like matrix, and that are therefore suitable for cartilage tissue engineering. It is shown that high basal levels of Slug prevent the chondrogenic differentiation of hMSCs, even in the presence of transforming growth factor-β and elevated levels of Sox9.

  15. Drought tolerance in eggs and juveniles of the Iberian slug, Arion lusitanicus.

    Science.gov (United States)

    Slotsbo, Stine; Fisker, Karina Vincents; Hansen, Lars Monrad; Holmstrup, Martin

    2011-12-01

    The spread of invasive species is an increasing problem world wide. The invasive slug Arion lusitanicus has spread to most parts of Europe, where it often is considered as a serious pest. There is a need for better knowledge of its ecophysiology to be able to predict the effect of climatic factors, such as temperature and humidity on the population dynamics and abundance. The aim of the present study was to assemble data on the water balance and drought tolerance of eggs and juveniles of A. lusitanicus. Both eggs and juveniles had little capacity to prevent evaporative water loss and lost water when the ambient humidity fell below 99.8 and 99.5%, respectively. The water conductance of the cuticle of juveniles was 242 μg cm(-2) h(-1) mmHg(-1) and resembles that of other slug species. Both eggs and juveniles of A. lusitanicus tolerate a substantial water loss. There was no difference in water loss resistance between eggs and juveniles, but the eggs were slightly more tolerant to water loss than the juveniles. The percent water loss causing 50% mortality was 72% for the juveniles and 81% for the eggs. Despite A. lusitanicus' tolerance of substantial water loss, its survival depends on humid habitats.

  16. Congruence between starch gel and polyacrylamide gel electrophoresis in detecting allozyme variation in pulmonate land slugs.

    Science.gov (United States)

    Geenen, Sofie; Jordaens, Kurt; Castilho, Rita; Backeljau, Thierry

    2003-02-01

    The predominantly selfing slug species Arion (Carinarion) fasciatus, A. (C.) silvaticus and A. (C.) circumscriptus are native in Europe and have been introduced into North America, where each species consists of a single, homozygous multilocus genotype (strain), as defined by starch gel electrophoresis (SGE) of allozymes. In Europe, the "one strain per species" hypothesis does not hold since polyacrylamide gel electrophoresis (PAGE) of allozymes uncovered 46 strains divided over the three species. However, electrophoretic techniques may differ in their ability to detect allozyme variation. Therefore, several Carinarion populations from both continents were screened by applying the two techniques simultaneously on the same individual slugs and enzyme loci. SGE and PAGE yielded exactly the same results, so that the different degree of variation in North American and European populations cannot be attributed to differences in resolving power between SGE and PAGE. We found four A. (C.) silvaticus strains in North America indicating that in this region the "one strain per species" hypothesis also cannot be maintained. Hence, the discrepancies between previous electrophoretic studies on Carinarion are most likely due to sampling artefacts and possible founder effects.

  17. Wire-mesh and ultrasound techniques applied for the characterization of gas-liquid slug flow

    Energy Technology Data Exchange (ETDEWEB)

    Ofuchi, Cesar Y.; Sieczkowski, Wytila Chagas; Neves Junior, Flavio; Arruda, Lucia V.R.; Morales, Rigoberto E.M.; Amaral, Carlos E.F.; Silva, Marco J. da [Federal University of Technology of Parana, Curitiba, PR (Brazil)], e-mails: ofuchi@utfpr.edu.br, wytila@utfpr.edu.br, neves@utfpr.edu.br, lvrarruda@utfpr.edu.br, rmorales@utfpr.edu.br, camaral@utfpr.edu.br, mdasilva@utfpr.edu.br

    2010-07-01

    Gas-liquid two-phase flows are found in a broad range of industrial applications, such as chemical, petrochemical and nuclear industries and quite often determine the efficiency and safety of process and plants. Several experimental techniques have been proposed and applied to measure and quantify two-phase flows so far. In this experimental study the wire-mesh sensor and an ultrasound technique are used and comparatively evaluated to study two-phase slug flows in horizontal pipes. The wire-mesh is an imaging technique and thus appropriated for scientific studies while ultrasound-based technique is robust and non-intrusive and hence well suited for industrial applications. Based on the measured raw data it is possible to extract some specific slug flow parameters of interest such as mean void fraction and characteristic frequency. The experiments were performed in the Thermal Sciences Laboratory (LACIT) at UTFPR, Brazil, in which an experimental two-phase flow loop is available. The experimental flow loop comprises a horizontal acrylic pipe of 26 mm diameter and 9 m length. Water and air were used to produce the two phase flow under controlled conditions. The results show good agreement between the techniques. (author)

  18. Glicerólise de óleo de peixe catalisada por lipase comercial de Rhizomucor miehei em meio com surfactante de grau alimentício Glycerolysis of fish oil catalyzed by a commercial lipase from Rhizomucor miehei in reaction media containing food grade surfactant

    OpenAIRE

    Joanna Silva Santos; Gisanara Dors; Débora de Oliveira; Soeli Francisca Mazzini Monte Blanco; José Vladimir de Oliveira; Agenor Furigo Júnior; Jorge Luiz Ninow; Maria Manuela Camino Feltes

    2013-01-01

    Omega-3 enriched partial acylglycerols are beneficial for human health. The aim of this study was to obtain monoacylglycerols (MAG) and diacylglycerols (DAG) by means of glycerolysis of fish oil catalyzed by a lipase from Rhizomucor miehei in the presence of food grade surfactants (Tween 65, 80 or 85). Glycerolysis was successful in the reaction media for all the tested surfactants, showing their potential for use as additives in such a system. The best results, however, were obtained for the...

  19. Preparation and characterization of bolaform surfactant vesicles.

    Science.gov (United States)

    Muzzalupo, Rita; Trombino, Sonia; Iemma, Francesca; Puoci, Francesco; La Mesa, Camillo; Picci, Nevio

    2005-12-10

    Vesicular formulations (liposomes and niosomes) play an increasingly important role since they can be used as drug delivery and targeting systems. We described the formation of two niosomal systems based on synthetic bolaform surfactants (4,7,10,13-pentaoxa-16-aza-cyclooctadecane)-hexadecanedioc acid diamide (BD-16) and alpha,omega-(4,7,10,13-pentaoxa-16-aza-cyclooctadecane)-hexadecane (BC-16). Systems containing BD-16 or BC-16 and different amount of cholesterol (CH) were prepared by aqueous dispersion of films, followed by examination of methylene blue (MB) entrapment, particle size and morphology. Indeed, we also studied the hydration in the distilled water and physiological solution, in order to investigate the complexing ability on vesicle formation. The results obtained in this study show a high encapsulation capacity and this ability and the size depends on cholesterol content.

  20. Degradation of Surfactants in Hydroponic Wheat Root Zones

    Science.gov (United States)

    Monje, Oscar; McCoy, Lashelle; Flanagan, Aisling

    Hygiene water recycling in recirculating hydroponic systems can be enhanced by plant roots by providing a substrate and root exudates for bacterial growth. However, reduced plant growth can occur during batch mode additions of high concentrations of surfactant. An analog hygiene water stream containing surfactants (Steol CS330, Mirataine CB) was added to a hydroponically-grown wheat plant root zone. The plants were grown at 700 mol mol-1 CO2, a photosynthetic photon flux of 300 mol m-2 s-1, and a planting density of 380 plants m-2. Volumetric oxygen mass transfer coefficients were determined using the fermentative/dynamic outgassing method to maintain adequate oxygen mass transfer rates in the root zone. This analysis suggested an optimal flow rate of the hydroponic solution of 5 L min-1. The hydroponic system was inoculated with biofilm from a bioreactor and rates of surfactant degradation were measured daily based on reduction in chemical oxygen demand (COD). The COD decreased from 400 to 100 mg L-1 after 2 days following batch addition of the analog hygiene water to the hydroponic system. Measurements of dissolved oxygen concentration and solution temperature suggest that the root zone was provided adequate aeration to meet both oxygen demands from plant and microbial respiration during the degradation of the surfactant. Results from this study show that hydroponic systems can be used to enhance rates of hygiene water processing.

  1. Comprehensive study of tartrazine/cationic surfactant interaction.

    Science.gov (United States)

    Shahir, Afshin Asadzadeh; Javadian, Soheila; Razavizadeh, Bi Bi Marzieh; Gharibi, Hussein

    2011-12-15

    Interaction of a food dye, tartrazine, with some cationic conventional and gemini surfactants, tetradecyltrimethylammonium bromide (TTAB), N,N'-ditetradecyl-N,N,N',N'-tetramethyl-N,N'-butanediyl-diammonium dibromide (14,4,14), and N,N'-didodecyl-N,N,N',N'-tetramethyl-N,N'-butanediyl-diammonium dibromide (12,4,12), were first investigated comprehensively employing conductometry, tensiometry, and UV-visible spectroscopy. Tartrazine was found to behave in the same manner as aromatic counterions. The formation of ion pairs reflected as a considerable increase of the surfactant efficiency in tensiometry plots and their stoichiometry were determined by Job's method of continuous variations. For the tartrazine/TTAB system, nonionic DS(3), ionic DS(2-), and/or DS(2)(-) ion pairs, their small premicelles, and tartrazine-rich micelles were constituted as well as dye-containing TTAB-rich micelles. Insoluble J-aggregates of DS(-) ion pairs and cylindrical surfactant-rich micelles were also formed in tartrazine/gemini surfactant systems and recognized by transmission electron microscopy. The zeta potential and the size of the aggregates were determined using dynamic light scattering and confirmed the suggested models for the processes happening in each system. Cyclic voltammetry was applied successfully to track all of these species using tartrazine's own reduction peak current for the first time.

  2. Microporosity of Bicontinuous Polymer Composites: Diffusion of Water and Surfactant

    Science.gov (United States)

    Kuta, K.; Challa, V.; Cheung, M.; Lopina, S.; von Meerwall, E.

    2000-10-01

    We have used the proton NMR pulsed-gradient spin-echo method to study the self-diffusion of water and surfactant in bicontinuous microcomposites formed with methyl methacrylate and hydroxy ethyl methacrylate, crosslinked with ethylene glycol dimethacrylate, in the presence of water containing 10 wt. percent sodium dodecyl sulfate as surfactant. Measurements were made over the full bicontinuous range of water content, (30 to 96 wt. percent) at 50 deg. C at a diffusion time of 12-15 ms. At spin-echo times greater than a few ms the echo of the glassy open-cell network phase was unobservable. The diffusivity spectrum of the mobile fraction is cleanly separable into two components differing by a factor of at least 30, attributable to water and surfactant. We find that the diffusivity of water increases with increasing water content, but that of the surfactant decreases. Measurements of restricted diffusion (non-adherence to Fick's second law) can reveal the size of the diffusionally accessible pores and its distribution, and their degree of interconnection. Corresponding measurements of time-resolved apparent diffusion are in progress.

  3. Online recognition of the multiphase flow regime and study of slug flow in pipeline

    Science.gov (United States)

    Liejin, Guo; Bofeng, Bai; Liang, Zhao; Xin, Wang; Hanyang, Gu

    2009-02-01

    single sensor performance. Among various flow patterns of gas-liquid flow, slug flow occurs frequently in the petroleum, chemical, civil and nuclear industries. In the offshore oil and gas field, the maximum slug length and its statistical distribution are very important for the design of separator and downstream processing facility at steady state operations. However transient conditions may be encountered in the production, such as operational upsets, start-up, shut-down, pigging and blowdown, which are key operational and safety issues related to oil field development. So it is necessary to have an understanding the flow parameters under transient conditions. In this paper, the evolution of slug length along a horizontal pipe in gas-liquid flow is also studied in details and then an experimental study of flowrate transients in slug flow is provided. Also, the special gas-liquid flow phenomena easily encountered in the life span of offshore oil fields, called severe slugging, is studied experimentally and some results are presented.

  4. Use of surfactants as plasticizers in preparing solid dispersions of poorly soluble API: selection of polymer-surfactant combinations using solubility parameters and testing the processability.

    Science.gov (United States)

    Ghebremeskel, Alazar N; Vemavarapu, Chandra; Lodaya, Mayur

    2007-01-10

    Formation of solid dispersions as a means to enhance the dissolution rate of poorly soluble Active pharmaceutical ingredients (APIs) typically employs hydrophilic polymer systems and surfactants. While the utility of the surfactant systems in solubilization is well known, the secondary effects of the same on processing and subsequent physical stability of the solid dispersions needs to be studied further. Physical blends of the poorly soluble API and hydrophilic polymers such as PVP-K30, Plasdone-S630, HPMC-E5, HPMCAS, and Eudragit L100 with mass ratio 1:1 were prepared. The surfactants tested in this study included Tween-80, Docusate sodium, Myrj-52, Pluronic-F68 and SLS. Thermal analysis of the API-polymer-surfactant blends suggested that the surfactants caused solvation/plasticization, manifesting in reduction of (i) the melting (T(m)) of API (ii) T(g) of the polymers and (iii) the combined T(g) of the solid dispersion formed from quench cooling. Explanation of these effects of surfactants is attempted based on their physical state (at the temperature of interest), HLB values and similarity of their solubility parameter values with respect to drug-polymer systems. Furthermore, extruded matrices containing different API-polymer (PVP-K30, Plasdone-S630, and HPMC-E5) mixtures prepared with and without surfactants, were produced by feeding the powder blend through a hot-melt extruder. The melt viscosity of the polymer blends was assessed by torque rheometry using a Haake Rheomix. The physicochemical properties of the extruded API-polymer-surfactant were characterized by differential scanning calorimetry, X-ray diffraction, Raman spectroscopy, and polarized microscopy. The results demonstrated that the glass transition temperature of the carrier polymers decreased as direct result of the surfactants in the extrudate, due to an increase in the chain mobility of polymers. A decrease in the melt viscosity was seen due to a plasticization of the polymer. The drug release

  5. Immunotoxicity of skin acid secretion produced by the sea slug Berthellina citrina in mice spleen: Histological and Immunohistochemical study.

    Science.gov (United States)

    Awaad, Aziz; Moustafa, Alaa Y

    2016-07-01

    Acid secretion containing sulfuric and hydrochloric acids is a fascinating defensive phenomenon within many groups of marine organisms. This study aimed to investigate the mice spleen histology and immunotoxicity using skin acid secretion (SAS) of the sea slug Berthellina citrina after oral administration. The spleen showed atrophy in the white pulp, decrease in the splenocytes density, megakaryocytes cytoplasmic degeneration as well as inflammatory cells infiltrations. The white and red pulp splenocytes number decreased time-dependently in the treated spleens. Additionally, the size of the megakaryocytes increased as compared with the control. The administration with SAS increased the number of the IgA(+) cells aggregation in the splenic red pulp. Furthermore, after 7days of the administration, large number of dispersed IgA(+) cells were distributed in splenic parenchyma. The IgA(+) cells numbers increased time-dependently as compared with those in the control. The aggregation sizes and number of the F4/80(+) cell in the splenic red pulp were increased. Furthermore the F4/80(+) cells numbers increased time-dependently as compared with those in the control. The UEAI(+) cells were found as free cells but not in aggregations in the control splenic red pulp. Contradictory to the number of IgA(+) cells and F4/80(+) cells the number of the UEAI(+) cells decreased time-dependently after administration with SAS. Hematologically, abnormal numbers of WBCs different cells were observed after administration with SAS. This study provides new insight about the toxicity of a marine extract may be used in natural products industry or medical applications.

  6. Biodegradability and aquatic toxicity of quaternary ammonium-based gemini surfactants: Effect of the spacer on their ecological properties.

    Science.gov (United States)

    Garcia, M Teresa; Kaczerewska, Olga; Ribosa, Isabel; Brycki, Bogumił; Materna, Paulina; Drgas, Małgorzata

    2016-07-01

    Aerobic biodegradability and aquatic toxicity of five types of quaternary ammonium-based gemini surfactants have been examined. The effect of the spacer structure and the head group polarity on the ecological properties of a series of dimeric dodecyl ammonium surfactants has been investigated. Standard tests for ready biodegradability assessment (OECD 310) were conducted for C12 alkyl chain gemini surfactants containing oxygen, nitrogen or a benzene ring in the spacer linkage and/or a hydroxyethyl group attached to the nitrogen atom of the head groups. According to the results obtained, the gemini surfactants examined cannot be considered as readily biodegradable compounds. The negligible biotransformation of the gemini surfactants under the standard biodegradation test conditions was found to be due to their toxic effects on the microbial population responsible for aerobic biodegradation. Aquatic toxicity of gemini surfactants was evaluated against Daphnia magna. The acute toxicity values to Daphnia magna, IC50 at 48 h exposure, ranged from 0.6 to 1 mg/L. On the basis of these values, the gemini surfactants tested should be classified as toxic or very toxic to the aquatic environment. However, the dimeric quaternary ammonium-based surfactants examined result to be less toxic than their corresponding monomeric analogs. Nevertheless the aquatic toxicity of these gemini surfactants can be reduced by increasing the molecule hydrophilicity by adding a heteroatom to the spacer or a hydroxyethyl group to the polar head groups.

  7. Practical Considerations and Challenges Involved in Surfactant Enhanced Bioremediation of Oil

    Directory of Open Access Journals (Sweden)

    Sagarika Mohanty

    2013-01-01

    Full Text Available Surfactant enhanced bioremediation (SEB of oil is an approach adopted to overcome the bioavailability constraints encountered in biotransformation of nonaqueous phase liquid (NAPL pollutants. Fuel oils contain n-alkanes and other aliphatic hydrocarbons, monoaromatics, and polynuclear aromatic hydrocarbons (PAHs. Although hydrocarbon degrading cultures are abundant in nature, complete biodegradation of oil is rarely achieved even under favorable environmental conditions due to the structural complexity of oil and culture specificities. Moreover, the interaction among cultures in a consortium, substrate interaction effects during the degradation and ability of specific cultures to alter the bioavailability of oil invariably affect the process. Although SEB has the potential to increase the degradation rate of oil and its constituents, there are numerous challenges in the successful application of this technology. Success is dependent on the choice of appropriate surfactant type and dose since the surfactant-hydrocarbon-microorganism interaction may be unique to each scenario. Surfactants not only enhance the uptake of constituents through micellar solubilization and emulsification but can also alter microbial cell surface characteristics. Moreover, hydrocarbons partitioned in micelles may not be readily bioavailable depending on the microorganism-surfactant interactions. Surfactant toxicity and inherent biodegradability of surfactants may pose additional challenges as discussed in this review.

  8. Direct Numerical Simulation of Insoluble Surfactant Effect on Turbulent Channel Bubbly Flows

    Science.gov (United States)

    Lu, Jiacai; Tryggvason, Gretar

    2016-11-01

    Direct Numerical Simulations (DNS) have been successfully used to obtain detailed data for turbulent channel bubbly flows. However, most of DNS that have been done so far remain problematic in comparing to most experiments. One of the major reasons is that real bubbly flows contain surfactants. The surfactants adhere to the interface, and produce an uneven distribution of the surfactant concentration due to the moving of bubbles and result in uneven surface tension over bubble surfaces. In this project, the effect of surfactants on the flow of many bubbles in an upward turbulent channel flow is studied by using of Direct Numerical Simulation with 3D Front-tracking method. The surfactant mass and the interfacial area are directly tracked in the method, and the surfactant mass remains conserved during the evolution. By using of different elasticity numbers in the non-linear equation of state which relates the surface tension to the surfactant concentration, the simulations show that the evolution of the turbulent channel bubbly flow are much different among the cases with contaminated bubbles and clean bubbles. Profiles of many parameters, such as streamwise velocity, shear stress and etc., are also compared at the statistically steady state for these cases. Research supported by DOE (CASL).

  9. Hydrophobic, electrostatic, and dynamic polymer forces at silicone surfaces modified with long-chain bolaform surfactants.

    Science.gov (United States)

    Rapp, Michael V; Donaldson, Stephen H; Gebbie, Matthew A; Das, Saurabh; Kaufman, Yair; Gizaw, Yonas; Koenig, Peter; Roiter, Yuri; Israelachvili, Jacob N

    2015-05-06

    Surfactant self-assembly on surfaces is an effective way to tailor the complex forces at and between hydrophobic-water interfaces. Here, the range of structures and forces that are possible at surfactant-adsorbed hydrophobic surfaces are demonstrated: certain long-chain bolaform surfactants-containing a polydimethylsiloxane (PDMS) mid-block domain and two cationic α, ω-quarternary ammonium end-groups-readily adsorb onto thin PDMS films and form dynamically fluctuating nanostructures. Through measurements with the surface forces apparatus (SFA), it is found that these soft protruding nanostructures display polymer-like exploration behavior at the PDMS surface and give rise to a long-ranged, temperature- and rate-dependent attractive bridging force (not due to viscous forces) on approach to a hydrophilic bare mica surface. Coulombic interactions between the cationic surfactant end-groups and negatively-charged mica result in a rate-dependent polymer bridging force during separation as the hydrophobic surfactant mid-blocks are pulled out from the PDMS interface, yielding strong adhesion energies. Thus, (i) the versatile array of surfactant structures that may form at hydrophobic surfaces is highlighted, (ii) the need to consider the interaction dynamics of such self-assembled polymer layers is emphasized, and (iii) it is shown that long-chain surfactants can promote robust adhesion in aqueous solutions.

  10. Phase Separation and Microstructure of Mixed Surfactants Solution Containing Cationic Geminis and Traditional Anionic Surfactant

    Institute of Scientific and Technical Information of China (English)

    尚亚卓; 刘洪来; 胡英

    2004-01-01

    The properties of aqueous two-phase system (ATPS) of mixed solution containing gemini cationic surfactant trimethylene-l,3-bis(dodecyldimethyl ammonium) bromide (12-3-12, 2Br-) and traditional anionic surfactant sodium dodecyl sulfate (SDS) with or without added salt have been studied. An ATPS is formed in a narrow region of the ternary phase diagram different from that of traditional aqueous cationic-anionic surfactant systems. In ATPS region, the lowest total concentration of surfactants varies with the mixing ratio of geminis to SDS. Photographs obtained from freeze-etching, negative-staining and transmission electron microscopy show that the microstructures of two phases are different from each other. Micelles and vesicles can coexist in a single phase. The addition of salts can change the phase diagram of ATPS. Furthermore, the added salts promote the aggregation of rod-like micelles to form coarse network structure that increase the viscosity of solutions. The negative ions of the added salts are the determining factor.

  11. Adsorption of dimeric surfactants in lamellar silicates

    Energy Technology Data Exchange (ETDEWEB)

    Balcerzak, Mateusz; Pietralik, Zuzanna [Department of Macromolecular Physics, Faculty of Physics, A. Mickiewicz University, Umultowska 85, 61-614 Poznań (Poland); Domka, Ludwik [Department of Metalorganic Chemistry, Faculty of Chemistry, A. Mickiewicz University, Grunwaldzka 6, 60-780 Poznań (Poland); Skrzypczak, Andrzej [Institute of Chemical Technology, Poznań University of Technology, Berdychowo 4, 60-965 Poznań (Poland); Kozak, Maciej, E-mail: mkozak@amu.edu.pl [Department of Macromolecular Physics, Faculty of Physics, A. Mickiewicz University, Umultowska 85, 61-614 Poznań (Poland)

    2015-12-01

    Highlights: • The intercalation of dimeric surfactants changed the morphology of MMT samples. • XRD indicated structures formed by surfactant molecules in interlayer space. • The four-step thermal decomposition of dimeric surfactant, confirms intercalation. - Abstract: The adsorption of different types of cationic surfactants in lamellar silicates changes their surface character from hydrophilic to hydrophobic. This study was undertaken to obtain lamellar silicates modified by a series of novel dimeric (gemini) surfactants of different length alkyl chains and to characterise these organophilised materials. Synthetic sodium montmorillonite SOMASIF® ME 100 (M) and enriched bentonite of natural origin (Nanoclay – hydrophilic bentonite®) were organophilised with dimeric (gemini) surfactants (1,1′-(1,4-butanediyl)bis(alkoxymethyl)imidazolium dichlorides). As a result of surfactant molecule adsorption in interlamellar space, the d-spacing (d{sub 001}) increased from 0.97 nm (for the anhydrous structure) to 2.04 nm. A Fourier transform infrared spectroscopy (FTIR) analysis of the modified systems reveals bands assigned to the stretching vibrations of the CH{sub 2} and CH{sub 3} groups and the scissoring vibrations of the NH group from the structure of the dimeric surfactants. Thermogravimetric (TG) and derivative thermogravimetric (DTG) studies imply a four-stage process of surfactant decomposition. Scanning electron microscopy (SEM) images provide information on the influence of dimeric surfactant intercalation into the silicate structures. Particles of the modified systems show a tendency toward the formation of irregularly shaped agglomerates.

  12. Surfactant therapy for bronchiolitis in critically ill infants.

    Science.gov (United States)

    Jat, Kana R; Chawla, Deepak

    2015-08-24

    Bronchiolitis is one of the most frequent causes of respiratory failure in infants; some infants will require intensive care and mechanical ventilation. There is lack of evidence regarding effective treatment for bronchiolitis other than supportive care. Abnormalities of surfactant quantity or quality (or both) have been observed in severe cases of bronchiolitis. Exogenous surfactant administration appears to favourably change the haemodynamics of the lungs and may be a potentially promising therapy for severe bronchiolitis. This is an update of a review published in Issue 9, 2012. We did not identify any new studies for inclusion, and our conclusions remain unchanged. To evaluate the efficacy of exogenous surfactant administration (i.e. intratracheal administration of surfactant of any type (whether animal-derived or synthetic), at any dose and at any time after start of ventilation) compared to placebo, no intervention or standard care in reducing mortality and the duration of ventilation in infants and children with bronchiolitis requiring mechanical ventilation. We searched the Cochrane Central Register of Controlled Studies (CENTRAL; 2015, Issue 5) which contains the Cochrane Acute Respiratory Infections Group's Specialised Register; MEDLINE (1948 to June week 3, 2015); EMBASE (1974 to June 2015); CINAHL (1982 to June 2015); LILACS (1985 to June 2015); and Web of Science (1985 to June 2015). We considered prospective, randomised controlled trials (RCTs) and quasi-RCTs evaluating the effect of exogenous surfactant in infants and children with bronchiolitis requiring mechanical ventilation. Two review authors selected studies independently. We extracted the data using a predefined proforma, independently analysed the data, and performed meta-analyses. We included three small RCTs enrolling 79 participants. Two trials did not use a placebo in the control arms and the third trial used air placebo. Two included studies reported no mortality. We judged all three of

  13. Banana Slug

    Science.gov (United States)

    First, Lucas

    2009-01-01

    Everyone insists that a person should go to a college that is right for him/her, somewhere that fits who he/she is, a place where a they belong. There are more than 4,000 colleges and universities in this country; how will a person find the one that is right for them? In this article, the author suggests that one should follow the mascot when…

  14. LOWER COST METHODS FOR IMPROVED OIL RECOVERY (IOR) VIA SURFACTANT FLOODING

    Energy Technology Data Exchange (ETDEWEB)

    William A. Goddard III; Yongchun Tang; Patrick Shuler; Mario Blanco; Seung Soon Jang; Shiang-Tai Lin; Prabal Maiti; Yongfu Wu; Stefan Iglauer; Xiaohang Zhang

    2004-09-01

    This report provides a summary of the work performed in this 3-year project sponsored by DOE. The overall objective of this project is to identify new, potentially more cost-effective surfactant formulations for improved oil recovery (IOR). The general approach is to use an integrated experimental and computational chemistry effort to improve our understanding of the link between surfactant structure and performance, and from this knowledge, develop improved IOR surfactant formulations. Accomplishments for the project include: (1) completion of a literature review to assemble current and new surfactant IOR ideas, (2) Development of new atomistic-level MD (molecular dynamic) modeling methodologies to calculate IFT (interfacial tension) rigorously from first principles, (3) exploration of less computationally intensive mesoscale methods to estimate IFT, Quantitative Structure Property Relationship (QSPR), and cohesive energy density (CED) calculations, (4) experiments to screen many surfactant structures for desirable low IFT and solid adsorption behavior, and (5) further experimental characterization of the more promising new candidate formulations (based on alkyl polyglycosides (APG) and alkyl propoxy sulfate surfactants). Important findings from this project include: (1) the IFT between two pure substances may be calculated quantitatively from fundamental principles using Molecular Dynamics, the same approach can provide qualitative results for ternary systems containing a surfactant, (2) low concentrations of alkyl polyglycoside surfactants have potential for IOR (Improved Oil Recovery) applications from a technical standpoint (if formulated properly with a cosurfactant, they can create a low IFT at low concentration) and also are viable economically as they are available commercially, and (3) the alkylpropoxy sulfate surfactants have promising IFT performance also, plus these surfactants can have high optimal salinity and so may be attractive for use in higher

  15. MATHEMATICAL MODELING OF THE PROCESSES OF RADIATION-CONVECTIVE HEAT EXCHANGE AT HEATING OF STEEL SLUGS IN METHODICAL TRANSFER FURNACES

    Directory of Open Access Journals (Sweden)

    I. A. Trusova

    2010-01-01

    Full Text Available The investigations on rational placement of burner devices in reheating furnaces with mechanized sole at the example of reheating furnace of mill 850 of RUP “BMZ” and determination of their force in dependence with grade assortment and slugs dimension types are given.

  16. Plastid-bearing sea slugs fix CO2 in the light but do not require photosynthesis to survive

    NARCIS (Netherlands)

    Christa, Gregor; Zimorski, Verena; Woehle, Christian; Tielens, Aloysius G M; Wägele, Heike; Martin, William F; Gould, Sven B

    2014-01-01

    Several sacoglossan sea slugs (Plakobranchoidea) feed upon plastids of large unicellular algae. Four species--called long-term retention (LtR) species--are known to sequester ingested plastids within specialized cells of the digestive gland. There, the stolen plastids (kleptoplasts) remain photosynt

  17. Plastid-bearing sea slugs fix CO2 in the light but do not require photosynthesis to survive

    NARCIS (Netherlands)

    G. Christa (Gregor); V. Zimorski (Verena); C. Woehle (Christian); A.G.M. Tielens (Aloysius); H. Wägele (Heike); W. Martin (William); D.B. Gould (Douglas )

    2013-01-01

    textabstractSeveral sacoglossan sea slugs (Plakobranchoidea) feed upon plastids of large unicellular algae. Four species-called long-term retention (LtR) species-are known to sequester ingested plastids within specialized cells of the digestive gland. There, the stolen plastids (kleptoplasts) remain

  18. The effect of climate manipulations on the herbivory of the pest slug Deroceras reticulatum (Müller, 1774) (Pulmonata: Agriolimacidae)

    Science.gov (United States)

    El-Danasoury, H.; Iglesias-Piñeiro, J.; Córdoba, M.

    2016-10-01

    The pestiferous status of the terrestrial slug Deroceras reticulatum and the strong dependence of its biology and ecology on climatic factors have driven research on the potential responses of the slug to predicted scenarios of climate change. Here, we report two short-term experiments performed outdoors, under seminatural conditions, to assess the behavioural response of D. reticulatum to different climate manipulations in terms of herbivory, by measuring over 7 days the damage inflicted by slug populations to lettuce seedlings. The climate manipulations tested emulate predicted climatic conditions for northwest Spain, specifically winter warming and increased summer rainfall, in contrast respectively with normal winter conditions and summer without rain conditions. In a winter experiment, we compared a normal winter treatment with a winter warming treatment; with respect to the normal winter treatment, the winter warming treatment was characterised by higher temperature, lower relative humidity and the absence of rainfall. In a summer experiment, we compared a summer drought treatment with an increased summer rainfall treatment; with respect to the summer drought treatment, the increased summer rainfall treatment was characterised by the presence of rainfall, while the conditions of temperature and relative humidity were similar in both treatments. Neither winter warming nor increased summer rainfall did lead to a significant increase on the number of seedlings damaged by the slugs. However, with both treatments, we found a moderate increase on the amount of damage suffered by the seedlings. The results are discussed in the context of the potential responses of D. reticulatum to future climatic conditions.

  19. The gastropod menace: slugs on Brassica plants affect caterpillar survival through consumption and interference with parasitoid attraction

    Science.gov (United States)

    Terrestrial molluscs and insect herbivores play a major role as plant consumers in a number of ecosystems, but their direct and indirect interactions have hardly been explored. The omnivorous nature of slugs makes them potential disrupters of predator-prey relationships, as a direct threat to small ...

  20. Hydrodynamics of gas-liquid slug flow along vertical pipes in turbulent regime-An experimental study

    Energy Technology Data Exchange (ETDEWEB)

    Mayor, T.S.; Ferreira, V.; Pinto, A.M.F.R. [Centro de Estudos de Fenomenos de Transporte, Departamento de Engenharia Quimica, Faculdade de Engenharia da Universidade do Porto, Rua Dr. Roberto Frias 4200-465 Porto (Portugal); Campos, J.B.L.M. [Centro de Estudos de Fenomenos de Transporte, Departamento de Engenharia Quimica, Faculdade de Engenharia da Universidade do Porto, Rua Dr. Roberto Frias 4200-465 Porto (Portugal)], E-mail: jmc@fe.up.pt

    2008-08-15

    An experimental study on free-bubbling gas-liquid (air-water) vertical slug flow was developed using a non-intrusive image analysis technique. The flow pattern in the near-wake of the bubbles and in the main liquid between bubbles was turbulent. A single correlation for the bubble-to-bubble interaction is proposed, relating the trailing bubble velocity to the length of the liquid slug ahead of the bubble. The proposed correlation is shown to be independent of column diameter, column vertical coordinate, superficial liquid and gas velocities and the velocity and length of the leading bubble. Frequency distribution curves, averages, modes and standard deviations are reported, for distributions of bubble velocity, bubble length and liquid slug length, for each experimental condition studied. Good agreement was found between theoretical predictions and experimental results regarding the upward velocity of undisturbed bubbles, in a 0.032 m internal diameter column. A considerable discrepancy was found, though, for a 0.052 m internal diameter column. The acquired experimental data are crucial for the development and validation of a robust slug flow simulator.

  1. Surfactants in tribology, v.3

    CERN Document Server

    Biresaw, Girma

    2013-01-01

    The manufacture and use of almost every consumer and industrial product rely on application of advanced knowledge in surface science and tribology. These two disciplines are of critical importance in major economic sectors, such as mining, agriculture, manufacturing (including metals, plastics, wood, computers, MEMS, NEMS, appliances), construction, transportation, and medical instruments, transplants, and diagnostic devices. An up-to-date reference with contributions by experts in surface science and tribology, Surfactants in Tribology, Volume 3 discusses some of the underlying tribological a

  2. Anaerobic Biodegradation of Detergent Surfactants

    OpenAIRE

    Erich Jelen; Ute Merrettig-Bruns

    2009-01-01

    Detergent surfactantscan be found in wastewater in relevant concentrations. Most of them are known as ready degradable under aerobic conditions, as required by European legislation. Far fewer surfactants have been tested so far for biodegradability under anaerobic conditions. The natural environment is predominantly aerobic, but there are some environmental compartments such as river sediments, sub-surface soil layer and anaerobic sludge digesters of wastewater treatment plants which have str...

  3. Communication: Light driven remote control of microgels' size in the presence of photosensitive surfactant: Complete phase diagram

    Science.gov (United States)

    Schimka, Selina; Gordievskaya, Yulia D.; Lomadze, Nino; Lehmann, Maren; von Klitzing, Regine; Rumyantsev, Artem M.; Kramarenko, Elena Yu.; Santer, Svetlana

    2017-07-01

    Here we report on a light triggered remote control of microgel size in the presence of photosensitive surfactant. The hydrophobic tail of the cationic surfactant contains azobenzene group that undergoes a reversible photo-isomerization reaction from a trans- to a cis-state accompanied by a change in the hydrophobicity of the surfactant. We have investigated light assisted behaviour and the complex formation of the microgels with azobenzene containing surfactant over the broad concentrational range starting far below and exceeding several times of the critical micelle concentration (CMC). At small surfactant concentration in solution (far below CMC), the surfactant in the trans-state accommodates within the microgel causing its compaction, while the cis-isomer desorbs out of microgel resulting in its swelling. The process of the microgel size change can be described as swelling on UV irradiation (trans-cis isomerization) and shrinking on irradiation with blue light (cis-trans isomerization). However, at the surfactant concentrations larger than CMC, the opposite behaviour is observed: the microgel swells on blue irradiation and shrinks during exposure to UV light. We explain this behaviour theoretically taking into account isomer dependent micellization of surfactant within the microgels.

  4. Orimulsion containment and recovery

    Energy Technology Data Exchange (ETDEWEB)

    Sommerville, M. [Briggs Marine Environmental Services, Aberdeen (United Kingdom)

    1999-01-01

    This paper focuses on the need for examination of Orimulsion fuel and its spill behaviour in the light of the anticipated increase in consumption of this fuel which comprises bitumen dispersed in water with addition of a small amount of surfactant. The behaviour and fate of Orimulsion at sea, and observations from experimental and sea trials are examined. The identification of spill control techniques, spill detection, the predictive modeling of the spill and response, sub-surface plume measurement, and containment and deflection are considered. Recovery of the bitumen produced from an Orimulsion spill, combined containment and recovery, dispersed Orimulsion, and beach cleaning are addressed. The properties of Orimulsion are tabulated. (UK)

  5. Stabilization of emulsions using polymeric surfactants based on inulin.

    Science.gov (United States)

    Tadros, Th F; Vandamme, A; Levecke, B; Booten, K; Stevens, C V

    2004-05-20

    The use of polymeric surfactants for stabilization of emulsions is described. A brief account of general classification and description of polymeric surfactants is given. This is followed by a description of the adsorption and conformation of polymeric surfactants at interfaces. The theoretical approaches for studying polymer adsorption are briefly described. This is followed by a section on the experimental techniques that can be applied to study adsorption and conformation of polymers at the interface. Examples are given to illustrate the experimental techniques. A section is devoted to the interaction between droplets containing adsorbed polymer layers (steric stabilization). The last section gives results on oil-in-water (O/W) emulsions stabilised with a novel graft copolymeric surfactant based on inulin that has been modified by introducing alkyl groups. Two oils were used, namely Isopar M (isoparaffinic oil) and cyclomethicone. Emulsions prepared using the inulin-based surfactant have large droplets, but this could be significantly reduced by addition of a cosurfactant in the oil phase, namely Span 20. The stability of the emulsions was investigated in water, in 0.5, 1.0, 1.5 and 2 mol dm(-3) NaCl and in 0.5, 1.0, 1.5 and 2 mol dm(-3) MgSO(4). These emulsions were stable for more than 1 year up to 50 degrees C in NaCl concentrations up to 2 mol dm(-3) and 1 mol dm(-3) MgSO(4). This high stability in high electrolyte concentrations could be attributed to the nature of the hydrophilic (stabilizing) polyfructose chain. This was confirmed using cloud point measurements, which showed high hydration of the polyfructose chain in such high electrolyte concentrations. This ensured the long-term physical stability resulting from the strong steric repulsion between the polyfructose chains.

  6. Surfactant inhibition in acute respiratory failure : consequences for exogenous surfactant therapy

    NARCIS (Netherlands)

    E.P. Eijking (Eric)

    1993-01-01

    textabstractThe neonatal respiratory distress syndrome (RDS) is characterized by immaturity of the lung, resulting in relative or absolute absence of pulmonary surfactant. Worldwide, neonates suffering from RDS have been treated successfully with exogenous surfactant preparations. Currently, exogeno

  7. A double injection ADSA-CSD methodology for lung surfactant inhibition and reversal studies.

    Science.gov (United States)

    Saad, Sameh M I; Policova, Zdenka; Dang, Andrew; Acosta, Edgar J; Hair, Michael L; Neumann, A Wilhelm

    2009-10-15

    This paper presents a continuation of the development of a drop shape method for film studies, ADSA-CSD (Axisymmetric Drop Shape Analysis-Constrained Sessile Drop). ADSA-CSD has certain advantages over conventional methods. The development presented here allows complete exchange of the subphase of a spread or adsorbed film. This feature allows certain studies relevant to lung surfactant research that cannot be readily performed by other means. The key feature of the design is a second capillary into the bulk of the drop to facilitate addition or removal of a secondary liquid. The development will be illustrated through studies concerning lung surfactant inhibition. After forming a sessile drop of a basic lung surfactant preparation, the bulk phase can be removed and exchanged for one containing different inhibitors. Such studies mimic the leakage of plasma and blood proteins into the alveolar spaces altering the surface activity of lung surfactant in a phenomenon called surfactant inhibition. The resistance of the lung surfactant to specific inhibitors can be readily evaluated using the method. The new method is also useful for surfactant reversal studies, i.e. the ability to restore the normal surface activity of an inhibited lung surfactant film by using special additives. Results show a distinctive difference between the inhibition when an inhibitor is mixed with and when it is injected under a preformed surfactant film. None of the inhibitors studied (serum, albumin, fibrinogen, and cholesterol) were able to penetrate a preexisting film formed by the basic preparation (BLES and protasan), while all of them can alter the surface activity of such preparation when mixed with the preparation. Preliminary results show that reversal of serum inhibition can be easily achieved and evaluated using the modified methodology.

  8. Response of graywater recycling systems based on hydroponic plant growth to three classes of surfactants

    Science.gov (United States)

    Garland, J. L.; Levine, L. H.; Yorio, N. C.; Hummerick, M. E.

    2004-01-01

    Anionic (sodium laureth sulfate, SLES), amphoteric (cocamidopropyl betaine, CAPB) and nonionic (alcohol polyethoxylate, AE) surfactants were added to separate nutrient film technique (NFT) hydroponic systems containing dwarf wheat (Triticum aestivum cv. USU Apogee) in a series of 21 day trials. Surfactant was added either in a (1). temporally dynamic mode (1-3 g surfactant m(-2) growing area d(-1)) as effected by automatic addition of a 300 ppm surfactant solution to meet plant water demand, or (2). continuous mode (2 g surfactant m(-2) growing area d(-1)) as effected by slow addition (10 mLh(-1)) of a 2000 ppm surfactant solution beginning at 4d after planting. SLES showed rapid primary degradation in both experiments, with no accumulation 24 h after initial addition. CAPB and AE were degraded less rapidly, with 30-50% remaining 24 h after initial addition, but CAPB and AE levels were below detection limit for the remainder of the study. No reductions in vegetative growth of wheat were observed in response to SLES, but biomass was reduced 20-25% with CAPB and AE. Microbial communities associated with both the plant roots and wetted hardware surfaces actively degraded the surfactants, as determined by monitoring surfactant levels following pulse additions at day 20 (with plants) and day 21 (after plant removal). In order to test whether the biofilm communities could ameliorate phytotoxicity by providing a microbial community acclimated for CAPB and AE decay, the continuous exposure systems were planted with wheat seeds after crop removal at day 21. Acclimation resulted in faster primary degradation (>90% within 24h) and reduced phytotoxicity. Overall, the studies indicate that relatively small areas (3-5m(2)) of hydroponic plant systems can process per capita production of mixed surfactants (5-10 g x person(-1)d(-1)) with minimal effects on plant growth.

  9. Micro-scale displacement of NAPL by surfactant and microemulsion in heterogeneous porous media

    Science.gov (United States)

    Javanbakht, Gina; Arshadi, Maziar; Qin, Tianzhu; Goual, Lamia

    2017-07-01

    Industrial processes such as remediation of oil-contaminated aquifers and enhanced oil recovery (EOR) often utilize chemical additives to increase the removal of non-aqueous phase liquids (NAPLs) from subsurface formations. Although the majority of crude oils are classified as LNAPLs, they often contain heavy molecules (DNAPLs) such as asphaltenes that tend to adsorb on minerals and alter their wettability. Effective additives are therefore those that can reduce the threshold capillary pressure, thus mobilizing LNAPL inside pore spaces and solubilizing DNAPL from rock surfaces. Nonionic surfactants in brine have often been injected to oil or contaminated aquifer formations in order to enhance NAPL displacement through IFT reduction. Recent studies revealed that surfactant-based microemulsions have a higher tendency to alter the wettability of surfaces, compared to surfactants alone, leading to more effective NAPL removal. However, the impact of these additives on pore-scale displacement mechanisms and multi-phase fluid occupancy in porous media is, to date, still unclear. In this study, x-ray microtomography experiments were performed to investigate the impact of surfactants and microemulsions on the mobilization and solubilization of NAPL in heterogeneous rocks. Saturation profiles indicated that an incremental NAPL removal was attained by addition of microemulsion to brine, compared with surfactant. Residual cluster size distributions revealed that microemulsions could break up large clusters into smaller disconnected ones, improving their mobilization in the rock. In-situ contact angle measurements showed that microemulsions could reverse the wettability of rough contaminated surfaces to a higher extent than surfactants. Unlike surfactant alone, the surfactant-solvent blend in the carrier fluid of microemulsions was able to penetrate rough grain surfaces, particularly those of dolomite cement, and desorb asphaltenes in the form of small-emulsified NAPL droplets

  10. Response of graywater recycling systems based on hydroponic plant growth to three classes of surfactants

    Science.gov (United States)

    Garland, J. L.; Levine, L. H.; Yorio, N. C.; Hummerick, M. E.

    2004-01-01

    Anionic (sodium laureth sulfate, SLES), amphoteric (cocamidopropyl betaine, CAPB) and nonionic (alcohol polyethoxylate, AE) surfactants were added to separate nutrient film technique (NFT) hydroponic systems containing dwarf wheat (Triticum aestivum cv. USU Apogee) in a series of 21 day trials. Surfactant was added either in a (1). temporally dynamic mode (1-3 g surfactant m(-2) growing area d(-1)) as effected by automatic addition of a 300 ppm surfactant solution to meet plant water demand, or (2). continuous mode (2 g surfactant m(-2) growing area d(-1)) as effected by slow addition (10 mLh(-1)) of a 2000 ppm surfactant solution beginning at 4d after planting. SLES showed rapid primary degradation in both experiments, with no accumulation 24 h after initial addition. CAPB and AE were degraded less rapidly, with 30-50% remaining 24 h after initial addition, but CAPB and AE levels were below detection limit for the remainder of the study. No reductions in vegetative growth of wheat were observed in response to SLES, but biomass was reduced 20-25% with CAPB and AE. Microbial communities associated with both the plant roots and wetted hardware surfaces actively degraded the surfactants, as determined by monitoring surfactant levels following pulse additions at day 20 (with plants) and day 21 (after plant removal). In order to test whether the biofilm communities could ameliorate phytotoxicity by providing a microbial community acclimated for CAPB and AE decay, the continuous exposure systems were planted with wheat seeds after crop removal at day 21. Acclimation resulted in faster primary degradation (>90% within 24h) and reduced phytotoxicity. Overall, the studies indicate that relatively small areas (3-5m(2)) of hydroponic plant systems can process per capita production of mixed surfactants (5-10 g x person(-1)d(-1)) with minimal effects on plant growth.

  11. COUPLING THE ALKALINE-SURFACTANT-POLYMER TECHNOLOGY AND THE GELATION TECHNOLOGY TO MAXIMIZE OIL PRODUCTION

    Energy Technology Data Exchange (ETDEWEB)

    Malcolm Pitts; Jie Qi; Dan Wilson

    2004-10-01

    Gelation technologies have been developed to provide more efficient vertical sweep efficiencies for flooding naturally fractured oil reservoirs or more efficient areal sweep efficiency for those with high permeability contrast ''thief zones''. The field proven alkaline-surfactant-polymer technology economically recovers 15% to 25% OOIP more oil than waterflooding from swept pore space of an oil reservoir. However, alkaline-surfactant-polymer technology is not amenable to naturally fractured reservoirs or those with thief zones because much of injected solution bypasses target pore space containing oil. This work investigates whether combining these two technologies could broaden applicability of alkaline-surfactant-polymer flooding into these reservoirs. A prior fluid-fluid report discussed interaction of different gel chemical compositions and alkaline-surfactant-polymer solutions. Gel solutions under dynamic conditions of linear corefloods showed similar stability to alkaline-surfactant-polymer solutions as in the fluid-fluid analyses. Aluminum-polyacrylamide, flowing gels are not stable to alkaline-surfactant-polymer solutions of either pH 10.5 or 12.9. Chromium acetate-polyacrylamide flowing and rigid flowing gels are stable to subsequent alkaline-surfactant-polymer solution injection. Rigid flowing chromium acetate-polyacrylamide gels maintained permeability reduction better than flowing chromium acetate-polyacrylamide gels. Silicate-polyacrylamide gels are not stable with subsequent injection of either a pH 10.5 or a 12.9 alkaline-surfactant-polymer solution. Neither aluminum citrate-polyacrylamide nor silicate-polyacrylamide gel systems produced significant incremental oil in linear corefloods. Both flowing and rigid flowing chromium acetate-polyacrylamide gels produced incremental oil with the rigid flowing gel producing the greatest amount. Higher oil recovery could have been due to higher differential pressures across cores. None of

  12. Soap opera : polymer-surfactant interactions on thin film surfaces /

    Energy Technology Data Exchange (ETDEWEB)

    Ozer, B. H. (Byram H.); Johal, M. S. (Malkiat S.); Wang, H. L. (Hsing-Lin); Robinson, J. M. (Jeanne M.)

    2001-01-01

    Surfactants are macromolecules with unique properties. They commonly contain a polar head group with a nonpolar hydrocarbon chain. These properties allow surfactants to solubilize greases and other nonpolar molecules. One particular way that this is accomplished is through the formation of micelles. Micelles are formed at the critical micelle concentration (cmc), which varies depending upon the nature of the surfactant and also the media in which the surfactant resides. These micelles can take a variety of shapes, but are generally characterized by surrounding the grease with the nonpolar hydrocarbon chains, exposing only the polarized head groups to the media, usually water. This property of easy solubilization has made surfactants a very attractive industrial agent, They are used most conventionally as industrial cleaning agents and detergents. However, they also have lesser-known applications in conjunction with polymers and other macromolecular mixtures, often creating a system with novel properties, such as increased solubilization and smoother mixture consistency. A recently developed field has investigated the self-assembly of polymers and polyelectrolytes onto thin film surfaces. There are many reasons for studying this process, such as for second harmonic generation purposes and bioassays. In this study, the interaction between the anionic polyelectrolyte poly[1-[4-(3-carboxy-4-hydroxyphenylazo)benzenesulfonamido]-1,2-ethanediyl, sodium salt] (PAZO) and two surfactants of opposite charge, Sodium Dodecyl Sulfate (SDS) and Dodecyl Trimethyl Ammonium Bromide (DTAB), in their assembly onto thin film surfaces was investigated. The kinetics of adsorbance onto the thin films was examined, followed by construction of 10-bilayer films using an alternating layer of the cationic polyelectrolyte poly(ethylenimine) (PEI) to provide the electrostatic means for the PAZO/surfactant combination to assemble onto the thin film. The kinetics of adsorption is being

  13. Biomimetic oligosaccharide and peptide surfactant polymers designed for cardiovascular biomaterials

    Science.gov (United States)

    Ruegsegger, Mark Andrew

    A common problem associated with cardiovascular devices is surface induced thrombosis initiated by the rapid, non-specific adsorption of plasma proteins onto the biomaterial surface. Control of the initial protein adsorption is crucial to achieve the desired longevity of the implanted biomaterial. The cell membrane glycocalyx acts as a non-thrombogenic interface through passive (dense oligosaccharide structures) and active (ligand/receptor interactions) mechanisms. This thesis is designed to investigate biomimicry of the cell glycocalyx to minimize non-specific protein adsorption and promote specific ligand/receptor interactions. Biomimetic macromolecules were designed through the molecular-scale engineering of polymer surfactants, utilizing a poly(vinyl amine) (PVAm) backbone to which hydrophilic (dextran, maltose, peptide) and hydrophobic alkyl (hexanoyl or hexanal) chains are simultaneously attached. The structure was controlled through the molar feed ratio of hydrophobic-to-hydrophilic groups, which also provided control of the solution and surface-active properties. To mimic passive properties, a series of oligomaltose surfactants were synthesized with increasing saccharide length (n = 2, 7, 15 where n is number of glucose units) to investigate the effect of coating height on protein adsorption. The surfactants were characterized by infra red (IR) and nuclear magnetic resonance (NMR) spectroscopies for structural properties and atomic force microscopy (AFM) and contact angle goniometry for surface activity. Protein adsorption under dynamic flow (5 dyn/cm2) was reduced by 85%--95% over the bare hydrophobic substrate; platelet adhesion dropped by ˜80% compared to glass. Peptide ligands were incorporated into the oligosaccharide surfactant to promote functional activity of the passive coating. The surfactants were synthesized to contain 0%, 25%, 50%, 75%, and 100% peptide ligand density and were stable on hydrophobic surfaces. The peptide surface density was

  14. Cationic versus anionic surfactant in tuning the structure and interaction of nanoparticle, protein, and surfactant complexes.

    Science.gov (United States)

    Mehan, Sumit; Aswal, Vinod K; Kohlbrecher, Joachim

    2014-08-26

    The structure and interaction in complexes of anionic Ludox HS40 silica nanoparticle, anionic bovine serum albumin (BSA) protein, and cationic dodecyl trimethylammonium bromide (DTAB) surfactant have been studied using small-angle neutron scattering (SANS). The results are compared with similar complexes having anionic sodium dodecyl sulfate (SDS) surfactant (Mehan, S; Chinchalikar, A. J.; Kumar, S.; Aswal, V. K.; Schweins, R. Langmuir 2013, 29, 11290). In both cases (DTAB and SDS), the structure in nanoparticle-protein-surfactant complexes is predominantly determined by the interactions of the individual two-component systems. The nanoparticle-surfactant (mediated through protein-surfactant complex) and protein-surfactant interactions for DTAB, but nanoparticle-protein (mediated through protein-surfactant complex) and protein-surfactant interactions for SDS, are found to be responsible for the resultant structure of nanoparticle-protein-surfactant complexes. Irrespective of the charge on the surfactant, the cooperative binding of surfactant with protein leads to micellelike clusters of surfactant formed along the unfolded protein chain. The adsorption of these protein-surfactant complexes for DTAB on oppositely charged nanoparticles gives rise to the protein-surfactant complex-mediated aggregation of nanoparticles (similar to that of DTAB surfactant). It is unlike that of depletion-induced aggregation of nanoparticles with nonadsorption of protein-surfactant complexes for SDS in similarly charged nanoparticle systems (similar to that of protein alone). The modifications in nanoparticle aggregation as well as unfolding of protein in these systems as compared to the corresponding two-component systems have also been examined by selectively contrast matching the constituents.

  15. Targeting miR-155 suppresses proliferation and induces apoptosis of HL-60 cells by targeting Slug/PUMA signal.

    Science.gov (United States)

    Liang, Hui; Dong, Ziyan; Liu, Jiang-Feng; Chuang, Wei; Gao, Li-Zhen; Ren, Yu-Guo

    2016-10-27

    Recent studies have shown that high miR-155 expression was associated with poor prognosis in patients with acute myelogeneous leukemia (AML). Furthermore, targeting miR-155 results in monocytic differentiation and apoptosis. However, the exact role and mechanisms of miR-155 in human AML remains speculative. HL-60 cells were treated with anti-miR-155 for 72 h. Cell growth and apoptosis in vitro were detected by MTT, BrdU proliferation, colony formation and flow cytometry assay. The effect of anti-miR-155 on growth of HL-60 cells was also evaluated in a leukemia mouse model. Slug cDNA and PUMA siRNA trannsfection was used to assess the signal pathway. Different protein expression was detected by western blot assay and quantitative reverse transcriptase polymerase chain reaction (qRT-PCR) assay. The results shown that targeting miR-155 resulted in a 24-fold decrease of miR-155 expression compared to negative control in the HL-60 cells. Targeting miR-155 significantly downregulated Slug and upregulated PUMA expression, and decreased HL-60 cell growth by 70% , impaired colony formation by approximately 60%, and increased HL-60 cell apoptosis by 45%. Targeting PUMA reversed miR-155 sliencing-induced proliferation and apoptosis of HL-60 cells. Restoration of Slug decreased PUMA expression. In murine engraftment models of HL-60 cells, we showed that targeting miR-155 was able to reduce tumor growth. This was accompanied with decreased Slug expression and increased PUMA expression in these tumors. Collectively, our findings strongly suggest targeting miR-155 exhibited in vivo and in vitro antileukemic activities in AML through a novel mechanism resulting in inhibition of Slug expression and increase of PUMA expression.

  16. Surfactant-enhanced cellulose nanocrystal Pickering emulsions.

    Science.gov (United States)

    Hu, Zhen; Ballinger, Sarah; Pelton, Robert; Cranston, Emily D

    2015-02-01

    The effect of surfactants on the properties of Pickering emulsions stabilized by cellulose nanocrystals (CNCs) was investigated. Electrophoretic mobility, interfacial tension, confocal microscopy and three-phase contact angle measurements were used to elucidate the interactions between anionic CNCs and cationic alkyl ammonium surfactants didecyldimethylammonium bromide (DMAB) and cetyltrimethylammonium bromide (CTAB). Both surfactants were found to adsorb onto CNCs with concentration-dependent morphology. At low concentrations, individual surfactant molecules adsorbed with alkyl tails pointing outward leading to hydrophobic CNCs. At higher concentrations, above the surfactant's apparent critical micelle concentration, surfactant aggregate morphologies on CNCs were inferred and the hydrophobicity of CNCs decreased. DMAB, which has two alkyl tails, rendered the CNCs more hydrophobic than CTAB which has only a single alkyl tail, at all surfactant concentrations. The change in CNC wettability from surfactant adsorption was directly linked to emulsion properties; adding surfactant increased the emulsion stability, decreased the droplet size, and controlled the internal phase of CNC Pickering emulsions. More specifically, a double transitional phase inversion, from oil-in-water to water-in-oil and back to oil-in-water, was observed for emulsions with CNCs and increasing amounts of DMAB (the more hydrophobic surfactant). With CNCs and CTAB, no phase inversion was induced. This work represents the first report of CNC Pickering emulsions with surfactants as well as the first CNC Pickering emulsions that can be phase inverted. The ability to surface modify CNCs in situ and tailor emulsions by adding surfactants may extend the potential of CNCs to new liquid formulations and extruded/spray-dried materials.

  17. The ultrastructural histochemistry and stereoscanning electron microscopy of the rodent and amphibian surfactant systems.

    Science.gov (United States)

    Stratton, C J; Wetzstein, H Y; Hardy, T

    1980-05-01

    Ultrastructural histochemical precedures were employed to determine the carbohydrate components and their contributions to the rodent and amphibian surfactant systems. Zirconium stained the rodent (rat) cytoplasm surrounding the multilamellar bodies, the Golgi, and was associated with the membrane structures of the compact lamellae of alveolar multilamellar bodies. In the rodent and amphibian (Rana pipiens), ruthenium red stain was observed within all tubular myelin surfactant matricies. The "gutters," tubular myelin surfactant matrix, and intratubular myelin surfactant matrix materials all demonstrated a positive reaction product. The periodic acid-chromic acid-silver procedure revealed irregular channels extending from the multilamellar bodies to the surface of the rodent great alveolar pneumocyte. The extra-pulmonary and respiratory surfaces in both species were additionally studied by stereoscanning electron microscopy. The respiratory anatomy of the rodent was corroborated. The amphibian lung demonstrated three orders of septa, and in the expired state, tertiary septal pits. The amphibian primary septa were hollow, blind tubules containing respiratory surfaces.

  18. Effects of surfactants on size and structure of amylose nanoparticles prepared by precipitation

    Indian Academy of Sciences (India)

    Yan Dong; Yanjiao Chang; Qian Wang; Jin Tong; Jiang Zhou

    2016-02-01

    The present work investigated the influence of surfactants on size and structure of amylose nanoparticles (ANPs) prepared through precipitation. ANPs were fabricated using absolute ethanol containing surfactants (Tween80, Span80 and mixtures of Tween80 and Span80 with ratios of 25/75, 50/50 and 75/25, respectively) as non-solvents. The obtained ANPs were characterized using dynamic light scattering (DLS), scanning electron microscopy and X-ray diffraction. The results showed that surfactant type, concentration and hydrophilic–lipophilic balance (HLB) value had great impact on size of precipitated ANPs. The smallest ANPs with mean size of 155 nm determined by DLS were obtained by using 0.5% (in proportion of the amylose solution volume) of Tween80/Span80 mixture (HLB = 12.33). The precipitated ANPs possessed the V-type crystalline structure no matter whether using the surfactants or not.

  19. Semi-quantitative determination of cationic surfactants in aqueous solutions using gold nanoparticles as reporter probes.

    Science.gov (United States)

    Kuong, Chi-Lap; Chen, Wei-Yu; Chen, Yu-Chie

    2007-03-01

    Concentrations of cationic surfactants in aqueous solutions have been estimated on the basis of changes in the color of gold nanoparticles, used as reporter probes. We have shown that the colors of gold nanoparticles with anionic protective groups on their surfaces shift from red to indigo/purple and then back to red in a range of cationic surfactant solutions in which concentrations vary from very low to above the theoretical CMCs. The color changes occur near the theoretical CMCs, presumably because the presence of surfactant micelles in the solution prevents the gold nanoparticles from aggregating. We have used gold nanoparticles as reporter probes to determine the concentrations of cationic surfactants in products such as hair conditioners, which often contain large amounts of alkyltrimethylammonium halides. Although this approach can only provide an estimate, it can be performed simply by addition of a given amount of gold nanoparticles to a series of diluted solutions, without the need for instruments or labor-intensive procedures.

  20. Modifying the electronic properties of single-walled carbon nanotubes using designed surfactant peptides

    Science.gov (United States)

    Samarajeewa, Dinushi R.; Dieckmann, Gregg R.; Nielsen, Steven O.; Musselman, Inga H.

    2012-07-01

    The electronic properties of carbon nanotubes can be altered significantly by modifying the nanotube surface. In this study, single-walled carbon nanotubes (SWCNTs) were functionalized noncovalently using designed surfactant peptides, and the resultant SWCNT electronic properties were investigated. These peptides have a common amino acid sequence of X(Valine)5(Lysine)2, where X indicates an aromatic amino acid containing either an electron-donating or electron-withdrawing functional group (i.e. p-amino-phenylalanine or p-cyano-phenylalanine). Circular dichroism spectra showed that the surfactant peptides primarily have random coil structures in an aqueous medium, both alone and in the presence of SWCNTs, simplifying analysis of the peptide/SWCNT interaction. The ability of the surfactant peptides to disperse individual SWCNTs in solution was verified using atomic force microscopy and ultraviolet-visible-near-infrared spectroscopy. The electronic properties of the surfactant peptide/SWCNT composites were examined using the observed nanotube Raman tangential band shifts and the observed additional features near the Fermi level in the scanning tunneling spectroscopy dI/dV spectra. The results revealed that SWCNTs functionalized with surfactant peptides containing electron-donor or electron-acceptor functional groups showed n-doped or p-doped altered electronic properties, respectively. This work unveils a facile and versatile approach to modify the intrinsic electronic properties of SWCNTs using a simple peptide structure, which is easily adaptable to obtain peptide/SWCNT composites for the design of tunable nanoscale electronic devices.The electronic properties of carbon nanotubes can be altered significantly by modifying the nanotube surface. In this study, single-walled carbon nanotubes (SWCNTs) were functionalized noncovalently using designed surfactant peptides, and the resultant SWCNT electronic properties were investigated. These peptides have a common amino

  1. Emulsion electrospinning of polycaprolactone: influence of surfactant type towards the scaffold properties.

    Science.gov (United States)

    Hu, Jue; Prabhakaran, Molamma P; Ding, Xin; Ramakrishna, Seeram

    2015-01-01

    Producing uniform nanofibers in high quality by electrospinning remains a huge challenge, especially using low concentrated polymer solutions. However, emulsion electrospinning assists to produce nanofibers from less concentrated polymer solutions compared to the traditional electrospinning process. The influence of individual surfactants towards the morphology of the emulsion electrospun poly (ɛ-caprolactone)/bovine serum albumin (PCL/BSA) nanofibers were investigated by using (i) non-ionic surfactant sorbitane monooleate (Span80); (ii) anionic sodium dodecyl sulfate (SDS); and (iii) cationic benzyltriethylammonium chloride, and poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) triblock copolymer Pluronic F108 of different concentrations. The morphology, along with the chemical and mechanical properties of the fibers, was evaluated by field emission scanning electron microscopy, attenuated total reflectance Fourier transform infrared spectroscopy, differential scanning calorimetry, water contact angle, and tensile tester. With the addition of surfactants, the electrospinnability of dilute PCL solution was enhanced, with either branched or uniform fibers were obtained. Electrospinning of an emulsion containing 0.4% (w/v) SDS produced the smallest and the most uniform nanofibers (167 ± 39 nm), which was attributed to the high conductivity of the solution. Analysis revealed that the emulsion electrospun nanofibers containing different surfactants and surfactant concentrations differ in fiber morphology and mechanical properties. Results suggest that surfactants have the ability to modulate the fiber morphology via electrostatic and hydrogen bonding, depending on their chemical structure.

  2. Surfactant mediated enhanced biodegradation of hexachlorocyclohexane (HCH) isomers by Sphingomonas sp. NM05.

    Science.gov (United States)

    Manickam, Natesan; Bajaj, Abhay; Saini, Harvinder S; Shanker, Rishi

    2012-09-01

    Environmental biodegradation of several chlorinated pesticides is limited by their low solubility and sorption to soil surfaces. To mitigate this problem we quantified the effect of three biosurfactant viz., rhamnolipid, sophorolipid and trehalose-containing lipid on the dissolution, bioavailability, and biodegradation of HCH-isomers in liquid culture and in contaminated soil. The effect of biosurfactants was evaluated through the critical micelle concentration (CMC) value as determined for each isomer. The surfactant increased the solubilization of HCH isomers by 3-9 folds with rhamnolipid and sophorolipid being more effective and showing maximum solubilization of HCH isomers at 40 μg/mL, compared to trehalose-containing lipid showing peak solubilization at 60 μg/mL. The degradation of HCH isomers by Sphingomonas sp. NM05 in surfactant-amended liquid mineral salts medium showed 30% enhancement in 2 days as compared to degradation in 10 days in the absence of surfactant. HCH-spiked soil slurry incubated with surfactant also showed around 30-50% enhanced degradation of HCH which was comparable to the corresponding batch culture experiments. Among the three surfactants, sophorolipid offered highest solubilization and enhanced degradation of HCH isomers both in liquid medium and soil culture. The results of this study suggest the effectiveness of surfactants in improving HCH degradation by increased bioaccessibility.

  3. Using biologically soft surfactants for dust suppression

    Energy Technology Data Exchange (ETDEWEB)

    Tkachenko, N.G.; Kolodiichak, V.K.; Motrii, A.E.; Severin, V.D.

    1982-07-01

    This article discusses environmental aspects of using surfactants in coal mines for dust suppression. Surfactants for underground black coal mines in the USSR are divided into three classes: so-called soft surfactants with a decomposition period from 1 to 3 days, hard surfactants with decomposition exceeding a month and an intermediary group. The decomposition process is analyzed; the role played by fermentation is stressed. Environmental effects of surfactant decomposition are evaluated. Selected surfactants tested in Soviet laboratories are described. The results of experimental use of diethanolamide as a surfactant for water injection in coal seams are evaluated. Wetting time amounts to 1 s when a 0.2% concentration is used. When surfactant concentration in water is reduced to 0.05% wetting time does not change; when concentration decreases to 0.025% wetting time increases to 3 s. Surfactant efficiency is investigated under operational conditions in a Donbass mine. Specifications of the working face, mining system and air pollution caused by a shearer loader are discussed. When diethanolamide is used dust suppression efficiency ranges from 86.4 to 90.4%. During the tests diethanolamide concentration in water was 0.05%.

  4. Remediation using trace element humate surfactant

    Energy Technology Data Exchange (ETDEWEB)

    Riddle, Catherine Lynn; Taylor, Steven Cheney; Bruhn, Debra Fox

    2016-08-30

    A method of remediation at a remediation site having one or more undesirable conditions in which one or more soil characteristics, preferably soil pH and/or elemental concentrations, are measured at a remediation site. A trace element humate surfactant composition is prepared comprising a humate solution, element solution and at least one surfactant. The prepared trace element humate surfactant composition is then dispensed onto the remediation site whereby the trace element humate surfactant composition will reduce the amount of undesirable compounds by promoting growth of native species activity. By promoting native species activity, remediation occurs quickly and environmental impact is minimal.

  5. Surfactant nebulisation : lung function, surfactant distribution and pulmonary blood flow distribution in lung lavaged rabbits

    NARCIS (Netherlands)

    Dijk, Peter H.; Heikamp, A; Bambang Oetomo, Sidarto

    1997-01-01

    Objective: Surfactant nebulisation is a promising alternative to surfactant instillation in newborns with the respiratory distress syndrome. Although less surfactant is deposited in the lung, it improves gas exchange, probably due to a superior distribution. We hypothesize that a more uniform distri

  6. Biophysical inhibition of pulmonary surfactant function by polymeric nanoparticles: role of surfactant protein B and C.

    Science.gov (United States)

    Beck-Broichsitter, Moritz; Ruppert, Clemens; Schmehl, Thomas; Günther, Andreas; Seeger, Werner

    2014-11-01

    The current study investigated the mechanisms involved in the process of biophysical inhibition of pulmonary surfactant by polymeric nanoparticles (NP). The minimal surface tension of diverse synthetic surfactants was monitored in the presence of bare and surface-decorated (i.e. poloxamer 407) sub-100 nm poly(lactide) NP. Moreover, the influence of NP on surfactant composition (i.e. surfactant protein (SP) content) was studied. Dose-elevations of SP advanced the biophysical activity of the tested surfactant preparation. Surfactant-associated protein C supplemented phospholipid mixtures (PLM-C) were shown to be more susceptible to biophysical inactivation by bare NP than phospholipid mixture supplemented with surfactant protein B (PLM-B) and PLM-B/C. Surfactant function was hindered owing to a drastic depletion of the SP content upon contact with bare NP. By contrast, surface-modified NP were capable of circumventing unwanted surfactant inhibition. Surfactant constitution influences the extent of biophysical inhibition by polymeric NP. Steric shielding of the NP surface minimizes unwanted NP-surfactant interactions, which represents an option for the development of surfactant-compatible nanomedicines.

  7. Surfactant nebulisation : lung function, surfactant distribution and pulmonary blood flow distribution in lung lavaged rabbits

    NARCIS (Netherlands)

    Dijk, Peter H.; Heikamp, A; Bambang Oetomo, Sidarto

    1997-01-01

    Objective: Surfactant nebulisation is a promising alternative to surfactant instillation in newborns with the respiratory distress syndrome. Although less surfactant is deposited in the lung, it improves gas exchange, probably due to a superior distribution. We hypothesize that a more uniform distri

  8. Sea slugs, subliminal pictures and vegetative state patients: Boundaries of consciousness in classical conditioning.

    Directory of Open Access Journals (Sweden)

    Tristan A Bekinschtein

    2011-12-01

    Full Text Available Classical (trace conditioning is a specific variant of associative learning in which a neutral stimulus leads to the subsequent prediction of an emotionally charged or noxious stimulus after a temporal gap. When conditioning is concurrent with a distraction task, only participants who can report the relationship (the contingency between stimuli explicitly show associative learning. This suggests that consciousness is a prerequisite for trace conditioning. We review and question three main controversies concerning this view. Firstly, virtually all animals, even invertebrate sea slugs, show this type of learning; secondly, unconsciously perceived stimuli may elicit trace conditioning; and thirdly, some vegetative state patients show trace learning. We discuss and analyze these seemingly contradictory arguments to find the theoretical boundaries of consciousness in classical conditioning. We conclude that trace conditioning remains one of the best measures to test conscious processing in the absence of explicit reports.

  9. Study on the tuning of the DTL cavity using slug tuners

    Energy Technology Data Exchange (ETDEWEB)

    Kwon, H. J.; Jo, Y. S.; Shim, C. B. [KAERI, Taejon (Korea, Republic of)

    2003-07-01

    20MeV DTL (Drift Tube Linac) is being developed as a low energy proton accelerator by PEFP (Proton Engineering Frontier Project). A DTL cavity consists of several tens of cells, and the errors of resonant frequency and accelerating field profile of the DTL cavity produced by machining and alignment errors can be adjusted and corrected by using slug tuners. To reduce time and effort to tune the cavity, tuning method including resonant frequency adjustment and field profile correction was developed. To validate the tuning method, numerical simulation about the first tank of the DTL was carried out. In this paper, the summary of the proposed tuning method and the simulation results are presented.

  10. SLUG - Stochastically Lighting Up Galaxies. II: Quantifying the Effects of Stochasticity on Star Formation Rate Indicators

    CERN Document Server

    da Silva, Robert L; Krumholz, Mark R

    2014-01-01

    The integrated light of a stellar population, measured through photometric filters that are sensitive to the presence of young stars, is often used to infer the star formation rate (SFR) for that population. However, these techniques rely on an assumption that star formation is a continuous process, whereas in reality stars form in discrete spatially- and temporally-correlated structures. This discreteness causes the light output to undergo significant time-dependent fluctuations, which, if not accounted for, introduce errors and biases in the inferred SFRs. We use SLUG (a code that Stochastically Lights Up Galaxies) to simulate galaxies undergoing stochastic star formation. We then use these simulations to present a quantitative analysis of these effects and provide tools for calculating probability distribution functions of SFRs given a set of observations. We show that, depending on the SFR tracer used, stochastic fluctuations can produce non-trivial errors at SFRs as high as 1 Msun/yr, and we suggest meth...

  11. A user interface for the Kansas Geological Survey slug test model.

    Science.gov (United States)

    Esling, Steven P; Keller, John E

    2009-01-01

    The Kansas Geological Survey (KGS) developed a semianalytical solution for slug tests that incorporates the effects of partial penetration, anisotropy, and the presence of variable conductivity well skins. The solution can simulate either confined or unconfined conditions. The original model, written in FORTRAN, has a text-based interface with rigid input requirements and limited output options. We re-created the main routine for the KGS model as a Visual Basic macro that runs in most versions of Microsoft Excel and built a simple-to-use Excel spreadsheet interface that automatically displays the graphical results of the test. A comparison of the output from the original FORTRAN code to that of the new Excel spreadsheet version for three cases produced identical results.

  12. Spatial variability of hydraulic conductivity of an unconfined sandy aquifer determined by a mini slug test

    DEFF Research Database (Denmark)

    Bjerg, Poul Løgstrup; Hinsby, Klaus; Christensen, Thomas Højlund;

    1992-01-01

    The spatial variability of the hydraulic conductivity in a sandy aquifer has been determined by a mini slug test method. The hydraulic conductivity (K) of the aquifer has a geometric mean of 5.05 × 10−4 m s−1, and an overall variance of 1n K equal to 0.37 which corresponds quite well to the results...... obtained by two large scale tracer experiments performed in the aquifer. A geological model of the aquifer based on 31 sediment cores, proposed three hydrogeological layers in the aquifer concurrent with the vertical variations observed with respect to hydraulic conductivity. The horizontal correlation...... length of the hydraulic conductivity has been determined for each of the three hydrogeological layers and is found to be small (1–2.5 m). The asymptotic longitudinal dispersivity of the aquifer has been estimated from the variance in hydraulic conductivity and the horizontal correlation length...

  13. Distribution and spread of the invasive slug Arion vulgaris Moquin-Tandon in Norway

    Directory of Open Access Journals (Sweden)

    Bjørn Arild Hatteland

    2013-02-01

    Full Text Available The present distribution of the invasive slug Arion vulgaris Moquin-Tandon was studied in Norway. This important pest species has spread to many parts of Europe during the last decades, inflicting damage to agriculture and domestic gardens. It was first recorded in Norway in 1988, and has since spread to many parts of the country and is now recorded in 192 municipalities. We surveyed the current distribution by sampling and gathering species records in cooperation with garden societies and local authorities. Based on these records, we present distributional data as well as relative predictions of future distributions based on geoclimatic parameters. Currently, A. vulgaris covers most of coastal southern Norway while it shows a patchy distribution in northern Norway, recorded as far north as Finnsnes in Troms County.

  14. Simultaneous PIV and pulsed shadow technique in slug flow: a solution for optical problems

    Energy Technology Data Exchange (ETDEWEB)

    Nogueira, S. [Karman Institute for Fluid Dynamics, Chaussee de Waterloo 72, B-1640, Rhode Saint Genese (Belgium); Centro de Estudos de Fenomenos de Transporte, Departamento de Eng. Quimica, Faculdade de Engenharia da Universidade do Porto, Rua Dr. Roberto Frias, 4200-465, Porto (Portugal); Sousa, R.G.; Pinto, A.M.F.R.; Campos, J.B.L.M. [Centro de Estudos de Fenomenos de Transporte, Departamento de Eng. Quimica, Faculdade de Engenharia da Universidade do Porto, Rua Dr. Roberto Frias, 4200-465, Porto (Portugal); Riethmuller, M.L. [Karman Institute for Fluid Dynamics, Chaussee de Waterloo 72, B-1640, Rhode Saint Genese (Belgium)

    2003-12-01

    A recent technique of simultaneous particle image velocimetry (PIV) and pulsed shadow technique (PST) measurements, using only one black and white CCD camera, is successfully applied to the study of slug flow. The experimental facility and the operating principle are described. The technique is applied to study the liquid flow pattern around individual Taylor bubbles rising in an aqueous solution of glycerol with a dynamic viscosity of 113 x 10{sup -3} Pa s. With this technique the optical perturbations found in PIV measurements at the bubble interface are completely solved in the nose and in annular liquid film regions as well as in the rear of the bubble for cases in which the bottom is flat. However, for Taylor bubbles with concave oblate bottoms, some optical distortions appear and are discussed. The measurements achieved a spatial resolution of 0.0022 tube diameters. The results reported show high precision and are in agreement with theoretical and experimental published data. (orig.)

  15. Development of Enzyme-Containing Functional Nanoparticles

    Science.gov (United States)

    2012-08-01

    absorbed) roentgen shake slug torr (nm Hg , 0° C) 1.000 000 X E -10 1.013 25 X E +2 1.000 000 X E +2 1.000 000 X E -28 1.054 350 X E +3 4 .184 000...nanoparticles, containing no enzyme, after particle synthesis to demonstrate that the adsorption of the enzyme or the presence of nanoparticles was not the...thermo-responsive nanoparticle nor enzyme adsorption onto the surface of the nanoparticle were responsible for artificially increasing enzymatic

  16. Evaluation of a common commercial surfactant in a water recycle system

    Energy Technology Data Exchange (ETDEWEB)

    Rector, T.; Jackson, A.; Rainwater, K. [Texas Tech Univ., Water Resources Center, Texas (United States); Pickering, S. [Johnson Space Center, NASA, Houston, Texas (United States)

    2002-06-15

    The fate of a common commercial surfactant was investigated in the biological reactors of a water recycle system. A NO{sub 2}{sup -} reducing packed-bed bioreactor was employed to evaluate degradation of surfactant present in a typical greywater stream. The research was conducted to determine if an alternative commercial surfactant could be used in a biological water recycle system proposed for space travel in place of the current surfactant. The commercial soap used in the research was Pert Plus for Kids (PPK), which contains sodium laureth sulfate (SLES) as the active surfactant. Experiments included a combination of microcosm studies as well as a continuous-flow packed-bed bioreactor. The hydraulic retention time of the packed-bed bioreactor was varied through changes in flow rate to yield different steady-state values for NO{sub 2}-N, TOC, and COD. Steady-state values will allow the determination of the bacterial kinetic parameters. Initial results suggest that the commercial surfactant may be difficult to treat in the time frame of typical biological systems. NO{sub 2}{sup -} reduction was favorable in the packed-bed reactor, but TOC removal rates did not correspond to the NO{sub 2}{sup -} removal. It is theorized that, due to its high K{sub oc} value (1200), SLES has an affinity to absorb to the media contained in the bed, which in turn allows for adsorption of the surfactant. Future research will include development of an isotherm model to characterize the adsorption rates and correlate them to surfactant removal. (author)

  17. Regulation of Membrane-Type 4 Matrix Metalloproteinase by SLUG Contributes to Hypoxia-Mediated Metastasis

    Directory of Open Access Journals (Sweden)

    Chi-Hung Huang

    2009-12-01

    Full Text Available The hypoxic tumor environment has been shown to be critical to cancer metastasis through the promotion of angiogenesis, induction of epithelial-mesenchymal transition (EMT, and acquisition of invasive potential. However, the impact of hypoxia on the expression profile of the proteolytic enzymes involved in invasiveness is relatively unknown. Membrane-type 4 matrix metalloproteinase (MT4-MMP is a glycosyl-phosphatidyl inositol-anchored protease that has been shown to be overexpressed in human cancers. However, detailed mechanisms regarding the regulation and function of MT4-MMP expression in tumor cells remain unknown. Here, we demonstrate that hypoxia or overexpression of hypoxia-inducible factor-1α (HIF-1α induced MT4-MMP expression in human cancer cells. Activation of SLUG, a transcriptional factor regulating the EMT process of human cancers, by HIF-1α was critical for the induction of MT4-MMP under hypoxia. SLUG regulated the transcription of MT4-MMP through direct binding to the E-box located in its proximal promoter. Short-interference RNA-mediated knockdown of MT4-MMP attenuated in vitro invasiveness and in vivo pulmonary colonization of tumor cells without affecting cell migratory ability. MT4-MMP promoted invasiveness and pulmonary colonization through modulation of the expression profile of MMPs and angiogenic factors. Finally, coexpression of HIF-1α and MT4-MMP in human head and neck cancer was predictive of a worse clinical outcome. These findings establish a novel signaling pathway for hypoxia-mediated metastasis and elucidate the underlying regulatory mechanism and functional significance of MT4-MMP in cancer metastasis.

  18. Volatile Elements Retention During Injection Casting of Metallic Fuel Slug for a Recycling Fast Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jong-Hwan; Song, Hoon; Kim, Hyung-Tae; Oh, Seok-Jin; Kuk, Seoung-Woo; Keum, Chang-Woon; Lee, Jung-Won; Kim, Ki-Hwan; Lee, Chan-Bock [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-10-15

    The as-cast fuels prepared by injection casting were sound and the internal integrities were found to be satisfactory through gamma-ray radiography. U and Zr were uniform throughout the matrix of the slug, and the impurities, i.e., oxygen, carbon, and nitrogen, satisfied the specification of the total impurities of less than 2000 ppm. The losses of the volatile Mn were effectively controlled using argon over pressures, and dynamic pumping for a period of time before injection showed no detrimental effect on the Mn loss by vaporization. This result suggests that volatile minor actinide-bearing fuels for SFRs can be prepared by improved injection methods. A practical process of metallic fuel fabrication for an SFR needs to be cost efficient, suitable for remote operation, and capable of mass production while reducing the amount of radioactive waste. Injection casting was chosen as the most promising technique, and this technique has been applied to fuel slug fabrication for the Experimental Breeder Reactor-II (EBR-II) driver and the Fast Flux Test Facility (FFTF) fuel pins. Because of the simplistic nature of the process and equipment, compared to other processes examined, this process has been successfully used in a remote operation environment for fueling of the EBR-II reactor. In this study, several injection casting methods were applied in order to prepare metallic fuel for an fast reactor that control the transport of volatile elements during fuel melting and casting. Mn was selected as a surrogate alloy since it possesses a total vapor pressure equivalent to that of a volatile minor actinide-bearing fuel. U.10Zr and U.10Zr.5Mn (wt%) metallic fuels were injection cast under various casting conditions and their soundness was characterized.

  19. The role of genetic and chemical variation of Pinus sylvestris seedlings in influencing slug herbivory.

    Science.gov (United States)

    O'Reilly-Wapstra, Julianne M; Iason, Glenn R; Thoss, Vera

    2007-05-01

    This study investigated the genetic and chemical basis of resistance of Pinus sylvestris seedlings to herbivory by a generalist mollusc, Arion ater. Using feeding trials with captive animals, we examined selective herbivory by A. ater of young P. sylvestris seedlings of different genotypes and correlated preferences with seedling monoterpene levels. We also investigated the feeding responses of A. ater to artificial diets laced with two monoterpenes, Delta(3)-carene and alpha-pinene. Logistic regression indicated that two factors were the best predictors of whether seedlings in the trial would be consumed. Individual slug variation (replicates) was the most significant factor in the model; however, alpha-pinene concentration (also representing beta-pinene, Delta(3)-carene and total monoterpenes due to multicollinearity) of needles was also a significant factor. While A. ater did not select seedlings on the basis of family, seedlings not eaten were significantly higher in levels of alpha-pinene compared to seedlings that were consumed. We also demonstrated significant genetic variation in alpha-pinene concentration of seedlings between different families of P. sylvestris. Nitrogen and three morphological seedling characteristics (stem length, needle length and stem diameter) also showed significant genetic variation between P. sylvestris families. Artificial diets laced with high (5 mg g(-1) dry matter) quantities of either Delta(3)-carene or alpha-pinene, were eaten significantly less than control diets with no added monoterpenes, supporting the results of the seedling feeding trial. This study demonstrates that A. ater selectively feed on P. sylvestris seedlings and that this selection is based, in part, on the monoterpene concentration of seedlings. These results, coupled with significant genetic variation in alpha-pinene concentration of seedlings and evidence that slug herbivory is detrimental to P. sylvestris fitness, are discussed as possible evidence for A

  20. Use of Viscosity to Probe the Interaction of Anionic Surfactants with a Coagulant Protein from Moringa oleifera Seeds

    Directory of Open Access Journals (Sweden)

    Raymond Maikokera

    2009-01-01

    Full Text Available The intrinsic viscosity of the coagulant protein was evaluated from the flow times of the protein solutions through a capillary viscometer, and the results suggested the coagulant protein to be globular. The interactions of the coagulant protein with anionic surfactant sodium dodecyl sulphate (SDS and sodium dodecyl benzene sulfonate (SDBS were also investigated by capillary viscometry. We conclude that there is strong protein-surfactant interaction at very low surfactant concentrations, and the behavior of the anionic surfactants in solutions containing coagulant protein is very similar. The viscometry results of protein-SDS system are compared with surface tension, fluorescence, and circular dichroism reported earlier. Combining the results of the four studies, the four approaches seem to confirm the same picture of the coagulant protein-SDS interaction. All the physical quantities when studied as function of surfactant concentration for 0.05% (w/v protein solution either exhibited a maximum or minimum at a critical SDS concentration.

  1. Lung preservation in experimental ischemia/reperfusion injury and lung transplantation: a comparison of natural and synthetic surfactants.

    Science.gov (United States)

    Knudsen, Lars; Boxler, Laura; Mühlfeld, Christian; Schaefer, Inga-Marie; Becker, Laura; Bussinger, Christine; von Stietencron, Immanuel; Madershahian, Navid; Richter, Joachim; Wahlers, Thorsten; Wittwer, Thorsten; Ochs, Matthias

    2012-01-01

    Surfactant inactivation results from ischemia/reperfusion injury and plays a major role in the pathogenesis of primary graft dysfunction after clinical lung transplantation. Thus, prophylactic administration of exogenous surfactant preparations before the onset of ischemia/reperfusion has proven to be effective in preserving pulmonary structure and function. Various natural and synthetic surfactant preparations exhibit differences regarding the biochemical composition and biophysical properties. In this study we compared the efficacy of preservation of pulmonary structure and function of the natural surfactant preparations Curosurf and Survanta to that of a synthetic surfactant containing an analog of surfactant protein C (SPC-33) in a rat model of ischemia/reperfusion injury. The oxygenation capacity and peak inspiratory pressure during the reperfusion period were recorded. By applying design-based stereology at the light- and electron-microscopic level, pathologic alterations, including alveolar edema, injury of the blood-air barrier and the intra-alveolar as well as intracellular surfactant pools, were quantified. The best oxygenation and preservation of lung structure was achieved with Curosurf. Survanta treatment was associated with the most severe injury of the blood-air barrier, and SPC-33 demonstrated signs of microatelectasis. The intra-alveolar surfactant pool after Curosurf and SPC-33 was dominated by active surfactant subtypes, whereas Survanta was associated with the highest fraction of inactive surfactant. The intracellular surfactant pool did not show any differences between the treatment groups. Taken together, Curosurf achieved the best structural and functional lung preservation, whereas Survanta was inferior to both Curosurf and SPC-33. Copyright © 2012 International Society for Heart and Lung Transplantation. Published by Elsevier Inc. All rights reserved.

  2. Characterization of Ni–P coating on AZ91D magnesium alloy with surfactants and nano-additives

    Directory of Open Access Journals (Sweden)

    Mohammed Sahal

    2014-12-01

    Full Text Available Direct electroless Ni–P plating was done on AZ91D magnesium alloy by immersing magnesium AZ91D samples into a bath containing Nickel sulphate. The nucleation mechanism of Ni–P deposits on the AZ91D magnesium alloy in the presence of surfactants and nano-additives was studied by using SEM. The electroless Ni–P deposits were preferentially nucleated on the βMg17Al12 phase of AZ91D magnesium alloy. Ni–P coating was coated uniformly in the presence of surfactants. Effect of surfactant C-Tab with varying quantities was studied. Addition of surfactant C-Tab homogenized the Ni–P deposition on AZ91D magnesium alloy surface. The effect produced by surfactant C-Tab was maximum with minimum addition (1 g/l of surfactant C-Tab further increase in the surfactant C-Tab quantity did not brought much changes in morphology. Effect of surfactant SLS was studied using SEM. Surfactant SLS when incorporated in small amounts (6 g/l and 12 g/l only exerted a slight influence in Ni–P deposition on AZ91D alloy surface. However Ni–P deposition was more uniform and spread throughout the surface with the addition of SLS surfactant (18 g/l. Effect of nano additives Al2O3, ZnO, SiO2 were studied. Nano additive Al2O3 enhanced the deposition of Ni–P on AZ91D alloy when added in 0.6 g/l quantity. SiO2 addition also gave the same results. ZnO addition influenced the Ni–P deposition on AZ91D alloy positively. Ni–P surface coating was coated more uniform and spread throughout the surface with the addition of surfactants and nano-additives.

  3. Development of PNA-Surfactant Systems for Nucleic Acid Separations

    Science.gov (United States)

    Vernille, James; Armitage, Bruce; Schneider, James

    2002-03-01

    We have been exploring the use of novel peptide nucleic acid (PNA) surfactants for use in sequence specific, scalable DNA separations. While the synthetic and physical characteristics of PNA make it a useful molecule for bioseparations, PNA shows limited water solubility. Here we describe a molecular design strategy to improve water solubility while maintaining sequence specificity. A candidate molecule has been identified which contains lysine residues and a short alkane tail. Melting temperature data show that lipid tail interactions with the DNA nucleobases have a small but significant effect on stability while the added lysines stabilize the complex in an ionic strength dependent way. We also discuss the incorporation of these surfactants into micellar systems for novel separations.

  4. Photoisomerization of merocyanine 540 in polymer-surfactant aggregate

    Indian Academy of Sciences (India)

    Sobhan Sen; Dipankar Sukul; Partha Dutta; Kankan Bhattacharyya

    2002-02-01

    Photoisomerization of merocyanine 540 (MC540) in a polymer-surfactant aggregate is studied using picosecond time resolved emission spectroscopy. The aggregate consists of the polymer, poly(vinylpyrrolidone) (PVP) and the surfactant, sodium dodecyl sulphate (SDS). With increase in the concentration of SDS in an aqueous solution of MC540 containing PVP, the emission quantum yield and lifetime of MC540 increase markedly. This indicates marked retardation in the nonradiative photoisomerization process of MC540, when it binds to the polymersurfactant aggregate. The critical association concentration of SDS for binding to PVP has been found to be 0.5 mM. This is about 16 times lower than the CMC of SDS in pure water (8 mM).

  5. Hemolysis by surfactants--A review.

    Science.gov (United States)

    Manaargadoo-Catin, Magalie; Ali-Cherif, Anaïs; Pougnas, Jean-Luc; Perrin, Catherine

    2016-02-01

    An overview of the use of surfactants for erythrocyte lysis and their cell membrane action mechanisms is given. Erythrocyte membrane characteristics and its association with the cell cytoskeleton are presented in order to complete understanding of the erythrocyte membrane distortion. Cell homeostasis disturbances caused by surfactants might induce changes starting from shape modification to cell lysis. Two main mechanisms are hypothesized in literature which are osmotic lysis and lysis by solubilization even if the boundary between them is not clearly defined. Another specific mechanism based on the formation of membrane pores is suggested in the particular case of saponins. The lytic potency of a surfactant is related to its affinity for the membrane and the modification of the lipid membrane curvature. This is to be related to the surfactant shape defined by its hydrophobic and hydrophilic moieties but also by experimental conditions. As a consequence, prediction of the hemolytic potency of a given surfactant is challenging. Several studies are focused on the relation between surfactant erythrolytic potency and their physico-chemical parameters such as the critical micellar concentration (CMC), the hydrophile-lipophile balance (HLB), the surfactant membrane/water partition coefficient (K) or the packing parameter (P). The CMC is one of the most important factors considered even if a lytic activity cut-off effect points out that the only consideration of CMC not enough predictive. The relation K.CMC must be considered in addition to the CMC to predict the surfactant lytic capacity within the same family of non ionic surfactant. Those surfactant structure/lytic activity studies demonstrate the requirement to take into account a combination of physico-chemical parameters to understand and foresee surfactant lytic potency.

  6. Utilisation des courbes de débit fractionnaire pour l'analyse des phénomènes de récupération par tensio-actif Using Fractional Flow Curves to Analyze Surfactant Recovery Phenomena

    Directory of Open Access Journals (Sweden)

    Moulu J. C.

    2006-11-01

    Full Text Available La connaissance des relations débit fractionnaire-saturation obtenues à partir des courbes de perméabilité relative a permis : - d'expliquer les mécanismes de formation et de propagation des différentes phases mobiles (eau et huile en place, phase aqueuse contenant du tensio-actif et/ou de polymère ; - de prévoir l'allure des courbes de récupération (en particulier la composition et le moment d'arrivée du banc d'huile en déplacement secondaire ou tertiaire ; ces courbe concordent sensiblement avec celles que l'on obtient à partir d'expériences de récupération ; - de tenir compte du volume du bouchon du tensio-actif injecté ; - les paramètres des solutions injectées (tension interfaciale, viscosité, adsorption. . . ayant un effet sur la forme des profils de débit fractionnaire, de mettre en relief le points importants pour l'optimisation des déplacements. Ce type d'analyse par lequel on traite ici un nombre limité de cas peut être généralisé et servir à contrôler les résultats d'expériences ou de simulations numériques. Knowing the fractional flow-saturation relations obtained from relative-permeability curves has made it possible: - to explain the formation and propagation mechanisms of different mobile phases (water and oil in place, aqueous phase containing surfactant and/or polymer ; - to predict the shape of recovery curves (in particular the composition and arrival time of the oil bank for secondary or tertiary recovery; these curves more or less agree with the ones obtained from recovery experiments; - to take into consideration the volume of the surfactant slug injected; - to highlight the important points for optimizing displacements using the parameters of injected solutions (interfacial tension, viscosity, adsorption, etc. having an effect on the shape of fractional flow profiles. This type of analysis, in which a limited number of cases are dealt with here, can be generalized and used to check the

  7. Innovation in surfactant therapy I: surfactant lavage and surfactant administration by fluid bolus using minimally invasive techniques.

    Science.gov (United States)

    Dargaville, Peter A

    2012-01-01

    Innovation in the field of exogenous surfactant therapy continues more than two decades after the drug became commercially available. One such innovation, lung lavage using dilute surfactant, has been investigated in both laboratory and clinical settings as a treatment for meconium aspiration syndrome (MAS). Studies in animal models of MAS have affirmed that dilute surfactant lavage can remove meconium from the lung, with resultant improvement in lung function. In human infants both non-randomised studies and two randomised controlled trials have demonstrated a potential benefit of dilute surfactant lavage over standard care. The largest clinical trial, performed by our research group in infants with severe MAS, found that lung lavage using two 15-ml/kg aliquots of dilute surfactant did not reduce the duration of respiratory support, but did appear to reduce the composite outcome of death or need for extracorporeal membrane oxygenation. A further trial of lavage therapy is planned to more precisely define the effect on survival. Innovative approaches to surfactant therapy have also extended to the preterm infant, for whom the more widespread use of continuous positive airway pressure (CPAP) has meant delaying or avoiding administration of surfactant. In an effort to circumvent this problem, less invasive techniques of bolus surfactant therapy have been trialled, including instillation directly into the pharynx, via laryngeal mask and via brief tracheal catheterisation. In a recent clinical trial, instillation of surfactant into the trachea using a flexible feeding tube was found to reduce the need for subsequent intubation. We have developed an alternative method of brief tracheal catheterisation in which surfactant is delivered via a semi-rigid vascular catheter inserted through the vocal cords under direct vision. In studies to date, this technique has been relatively easy to perform, and resulted in rapid improvement in lung function and reduced need for

  8. Model Lung Surfactant Films: Why Composition Matters

    Energy Technology Data Exchange (ETDEWEB)

    Selladurai, Sahana L.; Miclette Lamarche, Renaud; Schmidt, Rolf; DeWolf, Christine E.

    2016-10-18

    Lung surfactant replacement therapies, Survanta and Infasurf, and two lipid-only systems both containing saturated and unsaturated phospholipids and one containing additional palmitic acid were used to study the impact of buffered saline on the surface activity, morphology, rheology, and structure of Langmuir monolayer model membranes. Isotherms and Brewster angle microscopy show that buffered saline subphases induce a film expansion, except when the cationic protein, SP-B, is present in sufficient quantities to already screen electrostatic repulsion, thus limiting the effect of changing pH and adding counterions. Grazing incidence X-ray diffraction results indicate an expansion not only of the liquid expanded phase but also an expansion of the lattice of the condensed phase. The film expansion corresponded in all cases with a significant reduction in the viscosity and elasticity of the films. The viscoelastic parameters are dominated by liquid expanded phase properties and do not appear to be dependent on the structure of the condensed phase domains in a phase separated film. The results highlight that the choice of subphase and film composition is important for meaningful interpretations of measurements using model systems.

  9. Surfactant Adsorption: A Revised Physical Chemistry Lab

    Science.gov (United States)

    Bresler, Marc R.; Hagen, John P.

    2008-01-01

    Many physical chemistry lab courses include an experiment in which students measure surface tension as a function of surfactant concentration. In the traditional experiment, the data are fit to the Gibbs isotherm to determine the molar area for the surfactant, and the critical micelle concentration is used to calculate the Gibbs energy of micelle…

  10. Surfactant effects on soil aggregate tensile strength

    Science.gov (United States)

    Little is known regarding a soil aggregate's tensile strength response to surfactants that may be applied to alleviate soil water repellency. Two laboratory investigations were performed to determine surfactant effects on the tensile strength of 1) Ap horizons of nine wettable, agricultural soils co...

  11. New cationic vesicles prepared with double chain surfactants from arginine: Role of the hydrophobic group on the antimicrobial activity and cytotoxicity.

    Science.gov (United States)

    Pinazo, A; Petrizelli, V; Bustelo, M; Pons, R; Vinardell, M P; Mitjans, M; Manresa, A; Perez, L

    2016-05-01

    Cationic double chain surfactants have attracted much interest because they can give rise to cationic vesicles that can be used in biomedical applications. Using a simple and economical synthetic approach, we have synthesized four double-chain surfactants with different alkyl chain lengths (LANHCx). The critical aggregation concentration of the double chain surfactants is at least one order of magnitude lower than the CMC of their corresponding single-chain LAM and the solutions prepared with the LANHCx contain stable cationic vesicles. Encouragingly, these new arginine derivatives show very low haemolytic activity and weaker cytotoxic effects than conventional dialkyl dimethyl ammonium surfactants. In addition, the surfactant with the shortest alkyl chain exhibits good antimicrobial activity against Gram-positive bacteria. The results show that a rational design applied to cationic double chain surfactants might serve as a promising strategy for the development of safe cationic vesicular systems.

  12. Metathesis depolymerization for removable surfactant templates.

    Energy Technology Data Exchange (ETDEWEB)

    Zifer, Thomas (Sandia National Laboratories, Livermore, CA); Wheeler, David Roger; Rahimian, Kamayar; McElhanon, James Ross (Sandia National Laboratories, Livermore, CA); Long, Timothy Michael; Jamison, Gregory Marks; Loy, Douglas Anson (Los Alamos National Laboratories, Los Alamos, NM); Kline, Steven R. (National Institute of Standards and Technology, Gaithersburg, MD); Simmons, Blake Alexander (Sandia National Laboratories, Livermore, CA)

    2005-03-01

    Current methodologies for the production of meso- and nanoporous materials include the use of a surfactant to produce a self-assembled template around which the material is formed. However, post-production surfactant removal often requires centrifugation, calcination, and/or solvent washing which can damage the initially formed material architecture(s). Surfactants that can be disassembled into easily removable fragments following material preparation would minimize processing damage to the material structure, facilitating formation of templated hybrid architectures. Herein, we describe the design and synthesis of novel cationic and anionic surfactants with regularly spaced unsaturation in their hydrophobic hydrocarbon tails and the first application of ring closing metathesis depolymerization to surfactant degradation resulting in the mild, facile decomposition of these new compounds to produce relatively volatile nonsurface active remnants.

  13. Enhanced Oil Recovery with Surfactant Flooding

    DEFF Research Database (Denmark)

    Sandersen, Sara Bülow

    Enhanced oil recovery (EOR) is being increasingly applied in the oil industry and several different technologies have emerged during, the last decades in order to optimize oil recovery after conventional recovery methods have been applied. Surfactant flooding is an EOR technique in which the phase...... both for complex surfactant systems as well as for oil and brine systems. It is widely accepted that an increase in oil recovery can be obtained through flooding, whether it is simple waterflooding, waterflooding where the salinity has been modified by the addition or removal of specific ions (socalled...... “smart” waterflooding) or surfactant flooding. High pressure experiments have been carried out in this work on a surfactant system (surfactant/ oil/ brine) and on oil/ seawater systems (oil/ brine). The high pressure experiments were carried out on a DBR JEFRI PVT cell, where a glass window allows...

  14. The hydrophobicity of silicone-based oils and surfactants and their use in reactive microemulsions.

    Science.gov (United States)

    Castellino, Victor; Cheng, Yu-Ling; Acosta, Edgar

    2011-01-01

    In this work, for the first time, the Hydrophilic-Lipophilic Difference (HLD) framework for microemulsion formulation has been applied to silicone oils and silicone alkyl polyether surfactants. Based on the HLD equations and recently introduced mixing rules, we have quantified the hydrophobicity of the oils according to the equivalent alkane carbon number (EACN). We have found that, in a reference system containing sodium dihexyl sulfosuccinate (SDHS) as the surfactant, 0.65 centistoke (cSt) and 3.0 cSt silicone oils behave like n-dodecane and n-pentadecane, respectively. Silicone alkyl polyether surfactants were found to have characteristic curvatures ranging 3.4-18.9, exceeding that of most non-ionic surfactants. The introduction of methacrylic acid (MAA) and hydroxyethyl methacrylate (HEMA) to the aqueous phase caused a significant negative shift in HLD, indicative of an aqueous phase that is less hydrophilic than pure water. The more hydrophobic surfactants (largest positive curvatures) were used in order to compensate for this effect. These findings have led to the formulation of bicontinuous microemulsions (μEs) containing silicone oil, silicone alkyl polyether and reactive monomers in aqueous solution. Ternary phase diagrams of these systems revealed the potential for silicone-containing polymer composites with bicontinuous morphologies. These findings have also helped to explain the phase behavior of formulations previously reported in literature, and could help in providing a systematic, consistent approach to future silicone oil based microemulsion formulation.

  15. Research on the nanolevel influence of surfactants on structure formation of the hydrated Portland cement compositions

    Directory of Open Access Journals (Sweden)

    Guryanov Alexander

    2016-01-01

    Full Text Available The research of the structure formation process on a nanolevel of the samples of hydrated Portland cement compositions containing the modifying additives has been conducted with the help of small angle neutron scattering method. Carbonate and aluminum alkaline slimes as well as the complex additives containing surfactants were used as additives. The influence of slimes and surfactants on structural parameters change of Portland cement compositions of the average size of the disseminating objects, fractal dimension samples is considered. These Portland cement compositions are shown to be fractal clusters.

  16. Pulmonary surfactant in the airway physiology: a direct relaxing effect on the smooth muscle.

    Science.gov (United States)

    Calkovska, A; Uhliarova, B; Joskova, M; Franova, S; Kolomaznik, M; Calkovsky, V; Smolarova, S

    2015-04-01

    Beside alveoli, surface active material plays an important role in the airway physiology. In the upper airways it primarily serves in local defense. Lower airway surfactant stabilizes peripheral airways, provides the transport and defense, has barrier and anti-edematous functions, and possesses direct relaxant effect on the smooth muscle. We tested in vitro the effect of two surfactant preparations Curosurf® and Alveofact® on the precontracted smooth muscle of intra- and extra-pulmonary airways. Relaxation was more pronounced for lung tissue strip containing bronchial smooth muscle as the primary site of surfactant effect. The study does not confirm the participation of ATP-dependent potassium channels and cAMP-regulated epithelial chloride channels known as CFTR chloride channels, or nitric oxide involvement in contractile response of smooth muscle to surfactant.By controlling wall thickness and airway diameter, pulmonary surfactant is an important component of airway physiology. Thus, surfactant dysfunction may be included in pathophysiology of asthma, COPD, or other diseases with bronchial obstruction.

  17. Sono-electroanalysis of copper: enhanced detection and determination in the presence of surfactants.

    Science.gov (United States)

    Hardcastle, Joanna Lorraine; Hignett, Geraldine; Melville, James L; Compton, Richard G

    2002-04-01

    Surfactant adsorption has been shown to have a passivating effect on the electrode surface during anodic stripping voltammetric measurements. In the present work the feasibility of sono-anodic stripping analysis for the determination of copper in aqueous media contaminated with surfactant has been studied at an unmodified bare glassy carbon electrode. We illustrate the deleterious effect of three common surfactants, sodium dodecyl sulfate (SDS), dodecyl pyridinium chloride (DPC) and Triton-X 100 (TX-100) on conventional electroanalysis. The analogous sono-electroanalytical response was investigated for each surfactant at ultrasound intensities above and below the cavitation threshold. The enhancement in the stripping signal observed is attributed to the increased mass transport due to acoustic streaming and above the cavitation threshold the intensity of cavitational events is significantly increased leading to shearing of adsorbed surfactant molecules from the surface. As a result accurate analyses for SDS concentrations up to 100 ppm are possible, with analytical signals visible in solutions of SDS and TX-100 of 1000 ppm. Analysis is reported in high concentration of surfactant with use of sono-solvent double extraction. The power of this technique is clearly illustrated by the ability to obtain accurate measurements of copper concentration from starting solutions containing 1000 ppm SDS or TX-100. This was also exemplified by analysis of the low concentration 0.3 microM Cu(II) solution giving a percentage recovery of 94% in the presence of 1000 ppm SDS or TX-100.

  18. Fibrinogen stability under surfactant interaction.

    Science.gov (United States)

    Hassan, Natalia; Barbosa, Leandro R S; Itri, Rosangela; Ruso, Juan M

    2011-10-01

    Differential scanning calorimetry (DSC), circular dichroism (CD), difference spectroscopy (UV-vis), Raman spectroscopy, and small-angle X-ray scattering (SAXS) measurements have been performed in the present work to provide a quantitatively comprehensive physicochemical description of the complexation between bovine fibrinogen and the sodium perfluorooctanoate, sodium octanoate, and sodium dodecanoate in glycine buffer (pH 8.5). It has been found that sodium octanoate and dodecanoate act as fibrinogen destabilizer. Meanwhile, sodium perfluorooctanoate acts as a structure stabilizer at low molar concentration and as a destabilizer at high molar concentration. Fibrinogen's secondary structure is affected by all three studied surfactants (decrease in α-helix and an increase in β-sheet content) to a different extent. DSC and UV-vis revealed the existence of intermediate states in the thermal unfolding process of fibrinogen. In addition, SAXS data analysis showed that pure fibrinogen adopts a paired-dimer structure in solution. Such a structure is unaltered by sodium octanoate and perfluoroctanoate. However, interaction of sodium dodecanoate with the fibrinogen affects the protein conformation leading to a complex formation. Taken together, all results evidence that both surfactant hydrophobicity and tail length mediate the fibrinogen stability upon interaction. Copyright © 2011 Elsevier Inc. All rights reserved.

  19. Summer/winter variability of the surfactants in aerosols from Grenoble, France

    Science.gov (United States)

    Baduel, Christine; Nozière, Barbara; Jaffrezo, Jean-Luc

    2012-02-01

    Many atmospheric aerosols seem to contain strong organic surfactants likely to enhance their cloud-forming properties. Yet, few techniques allow for the identification and characterization of these compounds. Recently, we introduced a double extraction method to isolate the surfactant fraction of atmospheric aerosol samples, and evidenced their very low surface tension (≤30 mN m -1). In this work, this analytical procedure was further optimized. In addition to an optimized extraction and a reduction of the analytical time, the improved method led to a high reproducibility in the surface tension curves obtained (shapes and minimal values), illustrated by the low uncertainties on the values, ±10% or less. The improved method was applied to PM 10 aerosols from the urban area of Grenoble, France collected from June 2009 to January 2010. Significant variability was observed between the samples. The minimum surface tension obtained from the summer samples was systematically lower (30 mN m -1) than that of the winter samples (35-45 mN m -1). Sharp transitions in the curves together with the very low surface tensions suggested that the dominating surfactants in the summer samples were biosurfactants, which would be consistent with the high biogenic activity in that season. One group of samples from the winter also displayed sharp transitions, which, together with the slightly higher surface tension, suggested the presence of weaker, possibly man-made, surfactants. A second group of curves from the winter did not display any clear transition but were similar to those of macromolecular surfactants such as polysaccharides or humic substances from wood burning. These surfactants are thus likely to originate from wood burning, the dominating source for aerosols in Grenoble in winter. These observations thus confirm the presence of surfactants from combustion processes in urban aerosols reported by other groups and illustrates the ability of our method to distinguish between

  20. Expression of transcription factors Slug in the lens epithelial cells undergoing epithelial-mesenchymal transition induced by connective tissue growth factor

    Directory of Open Access Journals (Sweden)

    Ying-Na Wang

    2015-10-01

    Full Text Available AIM:To investigate the expression of transcription factors Slug in human lens epithelial cells (HLECs undergoing epithelial-mesenchymal transition (EMT induced by connective tissue growth factor (CTGF.METHODS: HLECs were treated with CTGF of different concentrations (20, 50 and 100 ng/mL or without CTGF (control for 24h. The morphological changes of HLECs were analysed by microscopy. The expression and cellular localization of Slug was evaluated by immumo-fluorescence. Expressions of Slug, E-cadherin and alpha smooth muscle actin (α-SMA were further determined by Western blot analysis. RESULTS: HLECs showed spidle fibrolasts-like characteristics and loosely connected each other after CTGF treatment. The immuno-fluorescence staining indicated that Slug was localized in the nuclei and its expression was induced by CTGF. The relative expressions of Slug protein were 1.64±0.11, 1.96 ±0.03, 3.12 ±0.10, and 4.08±0.14, respectively, in response to control group and treatment with CTGF of 20, 50 and 100 ng/mL (F=443.86, PCONCLUSION: Transcription factor Slug may be involved in EMT of HLECs induced by CTGF in vitro.

  1. Levels of the EMT-related protein Snail/Slug are not correlated with p53/p63 in cutaneous squamous cell carcinoma.

    Science.gov (United States)

    Chen, Hongxiang; Takahara, Masakazu; Xie, Lining; Takeuchi, Satoshi; Tu, Yating; Nakahara, Takeshi; Uchi, Hiroshi; Moroi, Yoichi; Furue, Masutaka

    2013-07-01

    The contribution of the E-cadherin transcriptional repressors Snail and Slug to invasion and metastasis has strengthened the evidence for the importance of epithelial-mesenchymal transition (EMT) in carcinoma progression. However, to the best of our knowledge, no study has described the immunohistochemical staining of the EMT-related proteins Snail/Slug in skin tumors and the correlation between Snail/Slug and tumor suppressor p53/p63. We performed immunohistological staining of Snail, Slug, E-cadherin, p53 and p63 in 20 archived specimens each of seborrheic keratosis (SK), actinic keratosis (AK) and squamous cell carcinoma in situ (SCCIS), and 53 specimens of cutaneous squamous cell carcinomas (SCC). Fifteen normal skin (NS) specimens served as controls. Significant negative correlations were observed between Snail and E-cadherin expression and between Slug and E-cadherin expression (Snail: R(2) = 0.5432, p Snail and Slug are associated with decreased E-cadherin staining in SCC and this may promote EMT. However, the staining intensities of p53 and p63 are not significantly correlated with the loss of E-cadherin. © 2013 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  2. Suppression of Invasion and Metastasis of Triple-Negative Breast Cancer Lines by Pharmacological or Genetic Inhibition of Slug Activity123

    Science.gov (United States)

    Ferrari-Amorotti, Giovanna; Chiodoni, Claudia; Shen, Fei; Cattelani, Sara; Soliera, Angela Rachele; Manzotti, Gloria; Grisendi, Giulia; Dominici, Massimo; Rivasi, Francesco; Colombo, Mario Paolo; Fatatis, Alessandro; Calabretta, Bruno

    2014-01-01

    Most triple-negative breast cancers (TNBCs) exhibit gene expression patterns associated with epithelial-to-mesenchymal transition (EMT), a feature that correlates with a propensity for metastatic spread. Overexpression of the EMT regulator Slug is detected in basal and mesenchymal-type TNBCs and is associated with reduced E-cadherin expression and aggressive disease. The effects of Slug depend, in part, on the interaction of its N-terminal SNAG repressor domain with the chromatin-modifying protein lysine demethylase 1 (LSD1); thus, we investigated whether tranylcypromine [also known as trans-2-phenylcyclopropylamine hydrochloride (PCPA) or Parnate], an inhibitor of LSD1 that blocks its interaction with Slug, suppresses the migration, invasion, and metastatic spread of TNBC cell lines. We show here that PCPA treatment induces the expression of E-cadherin and other epithelial markers and markedly suppresses migration and invasion of TNBC cell lines MDA-MB-231 and BT-549. These effects were phenocopied by Slug or LSD1 silencing. In two models of orthotopic breast cancer, PCPA treatment reduced local tumor growth and the number of lung metastases. In mice injected directly in the blood circulation with MDA-MB-231 cells, PCPA treatment or Slug silencing markedly inhibited bone metastases but had no effect on lung infiltration. Thus, blocking Slug activity may suppress the metastatic spread of TNBC and, perhaps, specifically inhibit homing/colonization to the bone. PMID:25499218

  3. VizieR Online Data Catalog: Slug analysis of star clusters in NGC 628 & 7793 (Krumholz+, 2015)

    Science.gov (United States)

    Krumholz, M. R.; Adamo, A.; Fumagalli, M.; Wofford, A.; Calzetti, D.; Lee, J. C.; Whitmore, B. C.; Bright, S. N.; Grasha, K.; Gouliermis, D. A.; Kim, H.; Nair, P.; Ryon, J. E.; Smith, L. J.; Thilker, D.; Ubeda, L.; Zackrisson, E.

    2016-02-01

    In this paper we use slug, the Stochastically Lighting Up Galaxies code (da Silva et al. 2012ApJ...745..145D, 2014MNRAS.444.3275D; Krumholz et al. 2015MNRAS.452.1447K), and its post-processing tool for analysis of star cluster properties, cluster_slug, to analyze an initial sample of clusters from the LEGUS (Calzetti et al. 2015AJ....149...51C). A description of the steps required to produce final cluster catalogs of the Legacy Extragalactic UV Survey (LEGUS) targets can be found in Calzetti et al. (2015AJ....149...51C), and in A. Adamo et al. (2015, in preparation). LEGUS is an HST Cycle 21 Treasury program that is imaging 50 nearby galaxies in five broadbands with the WFC3/UVIS, from the NUV to the I band. (1 data file).

  4. Evolution of transitional structures from puff to slug through multiple splitting in a pipe flow at low Reynolds number

    Science.gov (United States)

    Krauss, J.; Ertunç, Ö.; Ostwald, Ch; Lienhart, H.; Delgado, A.

    2011-12-01

    During laminar-to-turbulent transition in low Reynolds pipe flows, three main types of flow structures occur: traveling waves and the turbulent flow structures, namely puffs and slugs. In the present work, detailed experiments on the probability of occurrence and propagation speed of puffs, splitting puffs and slugs were conducted with the transition pipe-flow facility of LSTM-Erlangen. During the investigations, fully developed laminar pipe flow was triggered by an iris diaphragm with a pre-defined amplitude and lapse time. Different types of single and multiple puffs are classified and the probability of their occurrence as well as their propagation speed at the end of pipes with different lengths are evaluated.

  5. Evolution of transitional structures from puff to slug through multiple splitting in a pipe flow at low Reynolds number

    Energy Technology Data Exchange (ETDEWEB)

    Krauss, J; Ertunc, Oe; Ostwald, Ch; Lienhart, H; Delgado, A, E-mail: jens.krauss@lstm.uni-erlangen.de [Institute of Fluid Mechanics, FAU Erlangen-Nuremberg (Germany)

    2011-12-22

    During laminar-to-turbulent transition in low Reynolds pipe flows, three main types of flow structures occur: traveling waves and the turbulent flow structures, namely puffs and slugs. In the present work, detailed experiments on the probability of occurrence and propagation speed of puffs, splitting puffs and slugs were conducted with the transition pipe-flow facility of LSTM-Erlangen. During the investigations, fully developed laminar pipe flow was triggered by an iris diaphragm with a pre-defined amplitude and lapse time. Different types of single and multiple puffs are classified and the probability of their occurrence as well as their propagation speed at the end of pipes with different lengths are evaluated.

  6. Monitoring-well installation, slug testing, and groundwater quality for selected sites in South Park, Park County, Colorado, 2013

    Science.gov (United States)

    Arnold, Larry R. Rick

    2015-01-01

    During May–June, 2013, the U.S. Geological Survey, in cooperation with Park County, Colorado, drilled and installed four groundwater monitoring wells in areas identified as needing new wells to provide adequate spatial coverage for monitoring water quality in the South Park basin. Lithologic logs and well-construction reports were prepared for each well, and wells were developed after drilling to remove mud and foreign material to provide for good hydraulic connection between the well and aquifer. Slug tests were performed to estimate hydraulic-conductivity values for aquifer materials in the screened interval of each well, and groundwater samples were collected from each well for analysis of major inorganic constituents, trace metals, nutrients, dissolved organic carbon, volatile organic compounds, ethane, methane, and radon. Documentation of lithologic logs, well construction, well development, slug testing, and groundwater sampling are presented in this report.

  7. Surfactant replacement therapy--economic impact.

    Science.gov (United States)

    Pejaver, R K; al Hifzi, I; Aldussari, S

    2001-06-01

    Surfactant replacement is an effective treatment for neonatal respiratory distress syndrome. (RDS). As widespread use of surfactant is becoming a reality, it is important to assess the economic implications of this new form of therapy. A comparison study was carried out at the Neonatal Intensive Care Unit (NICU) of Northwest Armed Forces Hospital, Saudi Arabia. Among 75 infants who received surfactant for RDS and similar number who were managed during time period just before the surfactant was available, but by set criteria would have made them eligible for surfactant. All other management modalities except surfactant were the same for all these babies. Based on the intensity of monitoring and nursing care required by the baby, the level of care was divided as: Level IIIA, IIIB, Level II, Level I. The cost per day per bed for each level was calculated, taking into account the use of hospital immovable equipment, personal salaries of nursing, medical, ancillary staff, overheads and maintenance, depreciation and replacement costs. Medications used, procedures done, TPN, oxygen, were all added to individual patient's total expenditure. 75 infants in the Surfactant group had 62 survivors. They spent a total of 4300 days in hospital. (av 69.35) Out of which 970 d (av 15.65 per patient) were ventilated days. There were 56 survivors in the non-surfactant group of 75. They had spent a total of 5023 days in the hospital (av 89.69/patient) out of which 1490 were ventilated days (av 26.60 d). Including the cost of surfactant (two doses), cost of hospital stay for each infant taking the average figures of stay would be SR 118, 009.75 per surfactant treated baby and SR 164, 070.70 per non-surfactant treated baby. The difference of 46,061 SR is 39.03% more in non-surfactant group. One Saudi rial = 8 Rs (approx at the time study was carried out.) Medical care cost varies from place to place. However, it is definitely cost-effective where surfactant is concerned. Quality adjusted

  8. Surfactant-soil interactions during surfactant-amended remediation of contaminated soils by hydrophobic organic compounds: a review.

    Science.gov (United States)

    Laha, Shonali; Tansel, Berrin; Ussawarujikulchai, Achara

    2009-01-01

    Surfactants are amphiphilic molecules that reduce aqueous surface tension and increase the solubility of hydrophobic organic compounds (HOCs). Surfactant-amended remediation of HOC-contaminated soils and aquifers has received significant attention as an effective treatment strategy - similar in concept to using soaps and detergents as washing agents to remove grease from soiled fabrics. The proposed mechanisms involved in surfactant-amended remediation include: lowering of interfacial tension, surfactant solubilization of HOCs, and the phase transfer of HOC from soil-sorbed to pseudo-aqueous phase. However, as with any proposed chemical countermeasures, there is a concern regarding the fate of the added surfactant. This review summarizes the current state of knowledge regarding nonionic micelle-forming surfactant sorption onto soil, and serves as an introduction to research on that topic. Surfactant sorption onto soil appears to increase with increasing surfactant concentration until the onset of micellization. Sorbed-phase surfactant may account for the majority of added surfactant in surfactant-amended remediation applications, and this may result in increased HOC partitioning onto soil until HOC solubilization by micellar phase surfactant successfully competes with increased HOC sorption on surfactant-modified soil. This review provides discussion of equilibrium partitioning theory to account for the distribution of HOCs between soil, aqueous phase, sorbed surfactant, and micellar surfactant phases, as well as recently developed models for surfactant sorption onto soil. HOC partitioning is characterized by apparent soil-water distribution coefficients in the presence of surfactant.

  9. Micellization Behavior of Long-Chain Substituted Alkylguanidinium Surfactants

    Directory of Open Access Journals (Sweden)

    Roza Bouchal

    2016-02-01

    Full Text Available Surface activity and micelle formation of alkylguanidinium chlorides containing 10, 12, 14 and 16 carbon atoms in the hydrophobic tail were studied by combining conductivity and surface tension measurements with isothermal titration calorimetry. The purity of the resulting surfactants, their temperatures of Cr→LC and LC→I transitions, as well as their propensity of forming birefringent phases, were assessed based on the results of 1H and 13C NMR, differential scanning calorimetry (DSC, and polarizing microscopy studies. Whenever possible, the resulting values of Krafft temperature (TK, critical micelle concentration (CMC, minimum surface tension above the CMC, chloride counter-ion binding to the micelle, and the standard enthalpy of micelle formation per mole of surfactant (ΔmicH° were compared to those characterizing alkyltrimethylammonium chlorides or bromides with the same tail lengths. The value of TK ranged between 292 and 314 K and increased strongly with the increase in the chain length of the hydrophobic tail. Micellization was described as both entropy and enthalpy-driven. Based on the direct calorimetry measurements, the general trends in the CMC with the temperature, hydrophobic tail length, and NaCl addition were found to be similar to those of other types of cationic surfactants. The particularly exothermic character of micellization was ascribed to the hydrogen-binding capacity of the guanidinium head-group.

  10. Micellization Behavior of Long-Chain Substituted Alkylguanidinium Surfactants.

    Science.gov (United States)

    Bouchal, Roza; Hamel, Abdellah; Hesemann, Peter; In, Martin; Prelot, Bénédicte; Zajac, Jerzy

    2016-02-06

    Surface activity and micelle formation of alkylguanidinium chlorides containing 10, 12, 14 and 16 carbon atoms in the hydrophobic tail were studied by combining conductivity and surface tension measurements with isothermal titration calorimetry. The purity of the resulting surfactants, their temperatures of Cr→LC and LC→I transitions, as well as their propensity of forming birefringent phases, were assessed based on the results of ¹H and (13)C NMR, differential scanning calorimetry (DSC), and polarizing microscopy studies. Whenever possible, the resulting values of Krafft temperature (TK), critical micelle concentration (CMC), minimum surface tension above the CMC, chloride counter-ion binding to the micelle, and the standard enthalpy of micelle formation per mole of surfactant (ΔmicH°) were compared to those characterizing alkyltrimethylammonium chlorides or bromides with the same tail lengths. The value of TK ranged between 292 and 314 K and increased strongly with the increase in the chain length of the hydrophobic tail. Micellization was described as both entropy and enthalpy-driven. Based on the direct calorimetry measurements, the general trends in the CMC with the temperature, hydrophobic tail length, and NaCl addition were found to be similar to those of other types of cationic surfactants. The particularly exothermic character of micellization was ascribed to the hydrogen-binding capacity of the guanidinium head-group.

  11. Exogenous Pulmonary Surfactant as a Vehicle for Antimicrobials: Assessment of Surfactant-Antibacterial Interactions In Vitro

    Directory of Open Access Journals (Sweden)

    Alexei Birkun

    2014-01-01

    Full Text Available Owing to its unique surface-active properties, an exogenous pulmonary surfactant may become a promising drug delivery agent, in particular, acting as a vehicle for antibiotics in topical treatment of pneumonia. The purpose of this study was to assess a mutual influence of natural surfactant preparation and three antibiotics (amikacin, cefepime, and colistimethate sodium in vitro and to identify appropriate combination(s for subsequent in vivo investigations of experimental surfactant/antibiotic mixtures. Influence of antibiotics on surface-active properties of exogenous surfactant was assessed using the modified Pattle method. Effects of exogenous surfactant on antibacterial activity of antimicrobials against Staphylococcus aureus, Klebsiella pneumoniae, and Pseudomonas aeruginosa were evaluated using conventional microbiologic procedures. Addition of amikacin or cefepime to surfactant had no significant influence on surface-active properties of the latter. Obvious reduction of surface-active properties was confirmed for surfactant/colistimethate composition. When suspended with antibiotics, surfactant either had no impact on their antimicrobial activity (amikacin or exerted mild to moderate influence (reduction of cefepime bactericidal activity and increase of colistimethate bacteriostatic activity against S. aureus and P. aeruginosa. Considering favorable compatibility profile, the surfactant/amikacin combination is advisable for subsequent investigation of joint surfactant/antibacterial therapy in animals with bacterial pneumonia.

  12. Ecoulements Diphasiques à poches en conduite horizontale Horizontal Slug Flow in Pipes

    Directory of Open Access Journals (Sweden)

    Ferré D.

    2006-11-01

    Full Text Available Cette étude a eu pour objectif de préciser certains phénomènes caractéristiques des écoulements diphasiques rencontrés lors du transport par oléoducs des bruts pétroliers à teneur en gaz faible ou moyenne. Des expériences ont été réalisées à basse pression sur une boucle diphasique eau-air de diamètre 0,045 m et de longueur 50 m. Les mesures de présence de phase locale et de pression effectuées à la paroi pour des vitesses débitantes du liquide et du gaz variant respectivement entre 0,5 et 2 m/s et 0,3 et 10 m/s, ont permis d'accéder aux principales grandeurs cinématiques des écoulements à poches. A l'aide des méthodes classiques de l'analyse statistique, on a caractérisé l'aspect aléatoire de ces écoulements, la longueur d'établissement des régimes, la coalescence des poches. Enfin, en appliquant les équations diphasiques générales intégrées, on a précisé les ordres de grandeur et les tendances d'évolution de quelques lois phénoménologiques, pour en déduire une loi approchée du gradient de pression. The aim of this study is to describe various characteristic phenomena of two-phase flow encountered in the pipelining of crude oil with a love or medium gas content. Love-pressure experiments were performed with a two-phase water-air loop 0.045 mm in diameter and 50 m long. Measurements at the wall of local phase and pressure for liquid and gas flowrates varying between 0.5 and 2 m/s and 0.3 and 10 m/s revealed the leading kinematic magnitudes of slug flow. Conventional statistical-analysis methods were used ta characterize the random aspect of such flows, the length required for flow conditions ta be established and thé coalescence of slugs. General integrated two-phase équations were used to determine the orders of magnitude and variation tendencies of various phenomenological laves so as to deduce on approximate lave for the pressure gradient.

  13. Effects of surfactant on properties of MIM feedstock

    Institute of Scientific and Technical Information of China (English)

    LI Yi-min; LIU Xiang-quan; LUO Feng-hua; YUE Jian-ling

    2007-01-01

    Effects of the surfactant for improving the properties of MIM feedstock were investigated. Feedstocks were prepared by 17-4PH stainless steel(SS) powder and paraffin wax-based binder containing different contents of stearic acid(SA) as the surfactant. The viscosity of the feedstock decreases significantly when the SA is added. Besides, the wetting angle of the binder against the 17-4PH SS powder decreases greatly and the critical solid loading increases with the adding of the SA. Fourier transformation infrared spectroscopy(FTIR) analysis was used to prove the interaction between the SA and the 17-4PH SS powder. Chemical bonding is found on the surface of 17-4PH SS powder after mixing and it helps a lot to enhance the interacting force between the binder and the powder. Then an adsorbing model was adopted to estimate the least content of the surfactant that formed a monolayer adsorption on the mono-sized spherical powder (with smooth surface). The least content of the surfactant is calculated to be 0.19%. Whereas, the experiments indicate that about 5% is the optimal value to improve the properties of the feedstock. The reason may come from two aspects: firstly, the powders used in current experiment are not all mono-sized spheres and the coarse surface of the powder has a great effect on the adsorptive capacity of the powder; secondly, multilayer adsorption is likely to occur on the powder surface, which will also increase the adsorptive capacity.

  14. Digestive cell turnover in digestive gland epithelium of slugs experimentally exposed to a mixture of cadmium and kerosene.

    Science.gov (United States)

    Zaldibar, B; Cancio, I; Soto, M; Marigómez, I

    2007-11-01

    Slugs, Arion ater (L), have been proposed as sentinel organisms to assess soil health. In slugs under the influence of pollutants, digestive cell loss and the concomitant increase of excretory cells of the digestive gland have been described. The aim of the present work was to determine up to what extent digestive cell loss affects biomarkers and whether the affectation is reversible after exposure to a mixture of metal and organic pollutants. Slugs were dosed with a mixture of cadmium and kerosene in the food for 27 days. Apart from chemical analyses, the volume density of black silver deposits (Vv(BSD)) after autometallography, and acyl-CoA oxidase (AOX) activity were used as biomarkers of exposure to metals and organic compounds, respectively. As effect biomarkers, changes in the volume density of the cell types that constitute the digestive gland epithelium were calculated. Proliferating cells were identified by means of bromodeoxyuridine (BrdU) immunohistochemistry. Results revealed that the mixture of pollutants provoked an increase in Vv(BSD) and AOX activity and a decrease in the number of digestive cells. These changes had no effect in the digestive gland accumulation capacity or in the effect and exposure biomarkers employed. BrdU-labelling showed that exposure to pollutants provoked an enhanced digestive cell proliferation.

  15. The Slug and Churn Turbulence Characteristics of Oil-Gas-Water Flows in a Vertical Small Pipe

    Science.gov (United States)

    Liu, Weixin; Han, Yunfeng; Wang, Dayang; Zhao, An; Jin, Ningde

    2017-08-01

    The intention of the present study was to investigate the slug and churn turbulence characteristics of a vertical upward oil-gas-water three-phase flow. We firstly carried out a vertical upward oil-gas-water three-phase flow experiment in a 20-mm inner diameter (ID) pipe to measure the fluctuating signals of a rotating electric field conductance sensor under different flow patterns. Afterwards, typical flow patterns were identified with the aid of the texture structures in a cross recurrence plot. Recurrence quantitative analysis and multi-scale cross entropy (MSCE) algorithms were applied to investigate the turbulence characteristics of slug and churn flows with the varying flow parameters. The results suggest that with cross nonlinear analysis, the underlying dynamic characteristics in the evolution from slug to churn flow can be well understood. The present study provides a novel perspective for the analysis of the spatial-temporal evolution instability and complexity in oil-gas-water three-phase flow.

  16. Integrin β4 promotes cell invasion and epithelial-mesenchymal transition through the modulation of Slug expression in hepatocellular carcinoma

    Science.gov (United States)

    Li, Xiao-Long; Liu, Lin; Li, Dan-Dan; He, Ya-Ping; Guo, Le-Hang; Sun, Li-Ping; Liu, Lin-Na; Xu, Hui-Xiong; Zhang, Xiao-Ping

    2017-01-01

    Integrin β4 (ITGB4) is a transmembrane receptor involved in tumorigenesis and the invasiveness of many cancers. However, its role in hepatocellular carcinoma (HCC), one of the most prevalent human cancers worldwide, remains unclear. Here, we examined the involvement of ITGB4 in HCC and explored the underlying mechanisms. Real-time PCR and immunohistochemical analyses of tissues from 82 patients with HCC and four HCC cell lines showed higher ITGB4 levels in tumor than in adjacent non-tumor tissues and in HCC than in normal hepatic cells. Silencing of ITGB4 repressed cell proliferation, colony forming ability and cell invasiveness, whereas ectopic expression of ITGB4 promoted the proliferation and invasion of HCC cells and induced epithelial to mesenchymal transition (EMT) in parallel with the upregulation of Slug, as shown by transwell assays, WB and immunocytochemistry. Knockdown of Slug reduced cell viability inhibited invasion and reversed the effects of ITBG4 overexpression on promoting EMT, and AKT/Sox2-Nanog may also be involved. In a xenograft tumor model induced by injection of ITGB4-overexpressing cells into nude mice, ITGB4 promoted tumor growth and metastasis to the lungs. Taken together, our results indicate that ITGB4 plays a tumorigenic and pro-metastatic role mediated by Slug and suggest IGTB4 could be a prognostic indicator or a therapeutic target in patients with HCC. PMID:28084395

  17. Fluorescence emission of pyrene in surfactant solutions.

    Science.gov (United States)

    Piñeiro, Lucas; Novo, Mercedes; Al-Soufi, Wajih

    2015-01-01

    The systematic description of the complex photophysical behaviour of pyrene in surfactant solutions in combination with a quantitative model for the surfactant concentrations reproduces with high accuracy the steady-state and the time resolved fluorescence intensity of pyrene in surfactant solutions near the cmc, both in the monomer and in the excimer emission bands. We present concise model equations that can be used for the analysis of the pyrene fluorescence intensity in order to estimate fundamental parameters of the pyrene-surfactant system, such as the binding equilibrium constant K of pyrene to a given surfactant micelle, the rate constant of excimer formation in micelles, and the equilibrium constant of pyrene-surfactant quenching. The values of the binding equilibrium constant K(TX100)=3300·10³ M⁻¹ and K(SDS)=190·10³ M⁻¹ for Triton X-100 (TX100) and SDS micelles, respectively, show that the partition of pyrene between bulk water and micelles cannot be ignored, even at relatively high surfactant concentrations above the cmc. We apply the model to the determination of the cmc from the pyrene fluorescence intensity, especially from the intensity ratio at two vibronic bands in the monomer emission or from the ratio of excimer to monomer emission intensity. We relate the finite width of the transition region below and above the cmc with the observed changes in the pyrene fluorescence in this region.

  18. Tunable, antibacterial activity of silicone polyether surfactants.

    Science.gov (United States)

    Khan, Madiha F; Zepeda-Velazquez, Laura; Brook, Michael A

    2015-08-01

    Silicone surfactants are used in a variety of applications, however, limited data is available on the relationship between surfactant structure and biological activity. A series of seven nonionic, silicone polyether surfactants with known structures was tested for in vitro antibacterial activity against Escherichia coli BL21. The compounds varied in their hydrophobic head, comprised of branched silicone structures with 3-10 siloxane linkages and, in two cases, phenyl substitution, and hydrophilic tail of 8-44 poly(ethylene glycol) units. The surfactants were tested at three concentrations: below, at, and above their Critical Micelle Concentrations (CMC) against 5 concentrations of E. coli BL21 in a three-step assay comprised of a 14-24h turbidometric screen, a live-dead stain and viable colony counts. The bacterial concentration had little effect on antibacterial activity. For most of the surfactants, antibacterial activity was higher at concentrations above the CMC. Surfactants with smaller silicone head groups had as much as 4 times the bioactivity of surfactants with larger groups, with the smallest hydrophobe exhibiting potency equivalent to sodium dodecyl sulfate (SDS). Smaller PEG chains were similarly associated with higher potency. These data link lower micelle stability and enhanced permeability of smaller silicone head groups to antibacterial activity. The results demonstrate that simple manipulation of nonionic silicone polyether structure leads to significant changes in antibacterial activity.

  19. Influence of surf