WorldWideScience

Sample records for surfactant pluronic f68

  1. Influence of pluronic F68 on oxygen mass transfer.

    Science.gov (United States)

    Sieblist, Christian; Jenzsch, Marco; Pohlscheidt, Michael

    2013-01-01

    Pluronic F68 is one of the most used shear protecting additives in cell culture cultivations. It is well known from literature that such surface-active surfactants lower the surface tension at the gas-liquid interface, which influences the mass transfer. In this study, the effect of Pluronic F68 on oxygen mass transfer in aqueous solutions was examined. Therefore, the gassing in/gassing out method and bubble size measurements were used. At low concentrations of 0.02 g/L, a 50% reduction on mass transfer was observed for all tested spargers and working conditions. An explanation of the observed effects by means of Higbie's penetration or Dankwerts surface renewal theory was applied. It could be demonstrated that the suppressed movement of the bubble surface layer is the main cause for the significant drop down of the kL a-values. For Pluronic F68 concentrations above 0.1 g/L, it was observed that it comes to changes in bubble appearance and bubble size strongly dependent on the sparger type. By using the bubble size measurement data, it could be shown that only small changes in mass transfer coefficient (kL ) take place above the critical micelle concentration. Further changes on overall mass transfer at higher Pluronic F68 concentrations are mainly based on increasing of gas holdup and, more importantly, by increasing of the surface area available for mass transfer. © 2013 American Institute of Chemical Engineers.

  2. Pluronic F68 enhanced the conformational stability of salmon calcitonin in both aqueous solution and lyophilized solid form.

    Science.gov (United States)

    Lee, Ting-Huei; Lin, Shan-Yang

    2011-11-01

    The effects of different surfactants on the conformational stability and structural similarity of salmon calcitonin (sCT) in aqueous solution and lyophilized forms were investigated by using microscopic Fourier transform infrared (FTIR) spectroscopy with second-derivative spectral analysis. Six surfactants, HCO-60, sodium dodecyl sulfate (SDS), Tween 80, PEG 400, Pluronic 68, and F127 were selected. The sCT aqueous solution with or without different surfactants was, respectively, incubated at 40°C for up to 35 h. sCT films were casted on the CaF(2) plates and IR spectra were collected as a function of incubation time. Second derivative analysis showed that the native sCT having a major α-helical structure was gradually changed to the combination of α-helix, random coil, and β-sheet conformations in aqueous solution at 40°C. Similar conformational changes with delayed β-sheet formation were obtained for sCT after co-incubation with all the surfactants except Pluronic F68. When the native sCT was freeze-dried alone, a marked conformational alteration was found as illustrated by a poor spectral correlation coefficient (r) value of 0.823 as compared to that of the unlyophilized native sCT. This r value was significantly deviated from 1, strongly indicating the influence of lyophilization stress on the surfactant-free sCT. The r value for sCT after lyophilizing with HCO-60, Pluronic F127, PEG 400, or Pluronic F68 was >0.9, suggesting the possible stabilization of these surfactants in the lyophilization process. The sCT sample after lyophilizing with Pluronic F68 showed a highest r value (>0.968), indicating the most optimal stabilization effect of Pluronic F68 for sCT sample via lyophilization. Pluronic F68 was found to be the preferential surfactant for preventing the secondary structure changes in aqueous solution at 40°C as well as in lyophilized powder.

  3. Effects of Pluronic F68 on Manganese peroxidase production by pelletized Phanerochaete chrysosporium.

    Science.gov (United States)

    Li, Zhi-Min; Liu, Yan; Chi, Zhan-You; Chen, Shu-lin

    2011-06-01

    In this study, a new process was developed for manganese peroxidase (MnP) production by Phanerochaete chrysosporium under an agitated and aerated cultivation condition. It was found that change of the inoculum from spore suspension to pellets resulted in enhanced MnP production of 200 U/L in rotated shake flasks. Several additives, including Pluronic F68, Tween 80, and PEG8000, significantly increased the enzyme production. With an optimal concentration in 125 mL flasks, Pluronic F68 increased MnP productivity by 180%. Moreover, successful enzyme production was achieved in a 5-L fermentor at an agitation speed of 300 rpm with the addition of 0.1% Pluronic F68.

  4. Rheological Properties and Reverse Micelles Conditions of PEO-PPO-PEO Pluronic F68: Effects of Temperature and Solvent Mixtures

    Directory of Open Access Journals (Sweden)

    Mouna Ben Henda

    2013-01-01

    Full Text Available The rheological properties of Pluronic F68 were dissolved in various water/organic liquid mixtures over a wide range of temperatures, all at a concentration of 20 mg/mL. We have considered the following binary mixtures: Pluronic F68/water, F68/p-xylene, and F68/phenol. Various conformational transitions were detected and interpreted. We have also shown that these mixtures retain a Newtonian behavior independently of temperature and conformational changes. For ternary F68/p-xylene/water, F68/phenol/water, and F68/water/phenol mixtures, the behaviour of the solution is intimately related to the temperature and the amount of water and organic solvent added.

  5. Comparative antibacterial activity of silver nanoparticles synthesised by biological and chemical routes with pluronic F68 as a stabilising agent.

    Science.gov (United States)

    Santos, Carolina Alves Dos; Seckler, Marcelo Martins; Ingle, Avinash P; Rai, Mahendra

    2016-08-01

    The authors report the comparative antibacterial activity of silver nanoparticles synthesised by biological (using Fusarium oxysporum) and chemical routes in the presence and absence of pluronic F68 as a stabilising agent. The production of silver nanoparticles was evidenced by UV-visible spectra, with absorbance at about 420 nm in the case of both biological and chemical synthesis. X-ray diffraction pattern confirmed the presence of face-centred cubic structure (FCC plane). The nanoparticles characterised by transmission and scanning electron microscopy showed spherical silver nanoparticles with size range of 5-40 and 10-70 nm in the case of biologically and chemically synthesised nanoparticles, respectively. Addition of pluronic F68 showed the stabilisation of silver nanoparticles. Antibacterial efficacy of silver nanoparticles demonstrated different inhibitory activity against Escherichia coli, Pseudomonas aeruginosa and Staphylococcus aureus. Overall, biologically synthesised silver nanoparticles showed higher activity as compared with chemically synthesised nanoparticles. Silver nanoparticles synthesised in the presence of pluronic F68 by the chemical route exhibited synergism in antibacterial activity as compared with those synthesised without pluronic F68. On the contrary, biogenic silver nanoparticles without pluronic F68 showed higher antibacterial potential.

  6. Evaluating the impact of high Pluronic® F68 concentrations on antibody producing CHO cell lines.

    Science.gov (United States)

    Tharmalingam, Tharmala; Goudar, Chetan T

    2015-04-01

    Pluronic® F68 (P-F68) is an important component of chemically-defined cell culture medium because it protects cells from hydrodynamic and bubble-induced shear in the bioreactor. While P-F68 is typically used in cell culture medium at a concentration of 1 g/L (0.1%), higher concentrations can offer additional shear protection and have also been shown to be beneficial during cryopreservation. Recent industry experience with variability in P-F68-associated shear-protection has opened up the possibility of elevated P-F68 concentrations in cell culture media, a topic that has not been previously explored in the context of industrial cell culture processes. Recognizing this gap, we first evaluated the effect of 1-5 g/L P-F68 concentrations in shake flask cultures over ten 3-day passages for cell lines A and B. Increase in terminal cell density and cell size was seen over time at higher P-F68 concentrations but protein productivity was not impacted. Results from this preliminary screening study suggested no adverse impact of high P-F68 concentrations. Subsequently fed-batch bioreactor experiments were conducted at 1 and 5 g/L P-F68 concentrations with both cell lines where cell growth, viability, metabolism, and product quality were examined under process conditions reflective of a commercial process. Results from these bioreactor experiments confirmed findings from the preliminary screen and also indicated no impact of elevated P-F68 concentration on product quality. If additional shear protection is desired, either due to raw material variability, cell line sensitivity, or a high-shear cell culture process, our results suggest this can be accomplished by elevating the P-F68 concentration in the cell culture medium without impacting cell culture performance and product quality.

  7. Effects of Pluronic F-68 on Tetrahymena cells: protection against chemical and physical stress and prolongation of survival under toxic conditions

    DEFF Research Database (Denmark)

    Hellung-Larsen, P; Assaad, F; Pankratova, Stanislava

    2000-01-01

    concentrations of Ca2+ (70 microM); (c) prolongs the survival of cells exposed to higher ion concentrations (10 mM Ca2+, or Na+ or K+); (d) postpones the death caused by trace metal ions like Zn2+, Fe3+ and, Cu2+; (e) protects cells from the death caused by shearing forces; and (f) prolongs the survival of cells......The effects of the non-ionic surfactant Pluronic F-68 (0.01% w/v) on Tetrahymena cells have been studied. A marked protection against chemical and physical stress was observed. The chemical stress effects were studied in cells suspended in buffer (starvation) or in buffers with added ingredients...... from a chemically defined medium (Ca2+, Mg2+, Na+, K+, trace metal ions). The physical stress was due to mechanical stress or hyperthermia. The data show that Pluronic: (a) prolongs the survival of low concentration cell suspensions during starvation; (b) prevents the cell death caused by low...

  8. Antimicrobial effectiveness of silver nanoparticles co-stabilized by the bioactive copolymer pluronic F68

    Directory of Open Access Journals (Sweden)

    dos Santos Carolina Alves

    2012-11-01

    Full Text Available Abstract Background Silver nanoparticles (AgNps have attracted much interest in biomedical engineering, since they have excellent antimicrobial properties. Therefore, AgNps have often been considered for incorporation into medical products for skin pathologies to reduce the risk of contamination. This study aims at evaluating the antimicrobial effectiveness of AgNps stabilized by pluronic™ F68 associated with other polymers such as polyvinyl alcohol (PVA and polyvinylpyrrolidone (PVP. Methods AgNps antimicrobial activity was evaluated using the minimum inhibitory concentration (MIC method. The action spectrum was evaluated for different polymers associated with pluronic™ F68 against the gram negative bacteria P. aeuroginosa and E. coli and the gram positive bacteria S. Aureus. Results AgNps stabilized with PVP or PVA and co-stabilized with pluronic™ F68 are effective against E. coli and P. aeruginosa microorganisms, with MIC values as low as 0.78% of the concentration of the original AgNps dispersion. The antimicrobial action against S. aureus is poor, with MIC values not lower than 25%. Conclusions AgNps stabilized by different polymeric systems have shown improved antimicrobial activity against gram-negative microorganisms in comparison to unstabilized AgNps. Co-stabilization with the bioactive copolymer pluronic™ F68 has further enhanced the antimicrobial effectiveness against both microorganisms. A poor effectiveness has been found against the gram-positive S. aureus microorganism. Future assays are being delineated targeting possible therapeutic applications.

  9. Impact of Pluronic F-68 vs Tween 80 on Fabrication and Evaluation of Acyclovir SLNs for Skin Delivery.

    Science.gov (United States)

    Newton, Maria John; Kaur, Bhupinder

    2016-07-24

    The solid lipid nanoparticles (SLNs) of Acyclovir (ACV) were fabricated with Soya lecithin and Fractionated Coconut oil (medium chain glyceride) as a first time combination. The research was focused on developing ACV-SLN by using high pressure hot-homogenization technique. The ingredients were used in different concentrations and ratios to identify the best formulation design. The tween 80 and Pluronic F-68 were used in various concentrations in formulation design to assess the impact on the fabrication and evaluation of SLNs. The SLNs were subjected to various characterization techniques such as XRD ,FTIR, Master sizer analysis and zeta potential. The mean particle size was determined by master sizer and zeta sizer. Transmission electron microscopy (TEM) was used as a tool to analyze the morphology and other features. The zeta potential and drug entrapment efficiency (EE%) were also determined for the prepared ACV-SLNs. The efficiency of drug release from prepared formulations was studied by using in vitro study with the utilization of dialysis membrane technique. SLN dispersions exhibited the average size in nano range. SLNs with small particle size found to have predetermined encapsulation efficiency, and relatively high loading capacity and predetermined in vitro drug release profile.

  10. The Influence of Pluronic F68 and F127 Nanocarrier on Physicochemical Properties, In vitro Release, and Antiproliferative Activity of Thymoquinone Drug

    Science.gov (United States)

    Shaarani, Salwa; Hamid, Shahrul Sahul; Mohd Kaus, Noor Haida

    2017-01-01

    Background: This study reports on hydrophobic drug thymoquinone (TQ), an active compound found in the volatile oil of Nigella sativa that exhibits anticancer activities. Nanoformulation of this drug could potentially increase its bioavailability to specific target cells. Objective: The aim of this study was to formulate TQ into polymer micelle, Pluronic F127 (5.0 wt %) and Pluronic F68 (0.1 wt %), as a drug carrier to enhance its solubility and instability in aqueous media. Materials and Methods: Polymeric micelles encapsulated TQ were prepared by the microwave-assisted solvent evaporation technique. Fourier transform infrared spectroscopy and ultraviolet-visible spectrophotometer were utilized for qualitative confirmation of micelles encapsulation. The surface morphology and mean particle size of the prepared micelles were determined by using transmission electron microscopy (TEM). Cytotoxicity effect was studied using 3-(4,5-dimethylthiazol-2-yl)-5-(3-carboxymethoxyphenyl)-2-(4-sulfophenyl)-2H-tetrazolium, inner salt (MTS) assay. Results: Dynamic laser light scattering (DLS) technique showed hydrodynamic size distribution of optimized micelles of 50 nm, which was in close agreement with the mean particle size obtained from TEM of about 51 nm. Drug release study showed the maximum percentage of TQ release at 61% after 72 h, while the entrapment efficiency of TQ obtained was 46% using PF127. The cytotoxic effect of PF127-encapsulated TQ was considerably higher compared to PF68-encapsulated TQ against MCF7 cells, as they exhibited IC50value of 8 μM and 18 μM, respectively. Conclusion: This study suggests higher molecular weight Pluronic polymer micelles (F127) with hydrophilic-hydrophobic segments which could be used as a suitable candidate for sustainable delivery of TQ. However, comprehensive studies should be carried out to establish the suitability of Pluronic F127 as a carrier for other drugs with similar challenges as TQ. SUMMARY There is a rising interest

  11. Pluronic P85/F68 Micelles of Baicalein Could Interfere with Mitochondria to Overcome MRP2-Mediated Efflux and Offer Improved Anti-Parkinsonian Activity.

    Science.gov (United States)

    Chen, Tongkai; Li, Ye; Li, Chuwen; Yi, Xiang; Wang, Ruibing; Lee, Simon Ming-Yuen; Zheng, Ying

    2017-10-02

    Overexpression of the drug efflux transporter multidrug resistance-associated protein 2 (MRP2) in the gastrointestinal tract and blood-brain barrier compromises the oral delivery of drugs to the circulation system and brain in the treatment of Parkinson's disease (PD). In this study, we aim to develop small-sized Pluronic P85/F68 micelles loaded with baicalein (B-MCs) to overcome MRP2-mediated efflux and to investigate related mechanism, as well as the anti-Parkinsonian efficacy. Spherical and sustained-release B-MCs have a mean particle size of 40.61 nm, a low critical micelle concentration (CMC) of 5.01 × 10(-3) mg/mL with an encapsulation efficiency of 95.47% and a drug loading of 7.07%. In comparison with the free baicalein, the cellular uptake and apparent permeability coefficient (Papp) of B-MCs were significantly enhanced (p < 0.01). Fluorescence resonance energy transfer (FRET) analysis indicated that micelles carrying the hydrophobic fluorophores were internalized intact, followed by a rapid release of fluorophores inside the cells, and then the released free fluorophores were transported across the cell monolayers to the basolateral side. Further study on the MRP2 inhibitory effect showed that B-MCs could reverse the MRP2-mediated efflux of baicalein via interfering with the structure and function of mitochondria, i.e., reducing mitochondrial membrane potential and intracellular ATP level and influencing the respiration chain of mitochondria. In addition, B-MCs exerted strong neuroprotective effects on zebrafish model of PD. In summary, Pluronic P85/F68 micelles could be considered as a promising drug delivery system to reverse MRP2-mediated efflux and improve the bioactivity of this MRP2 substrate, baicalein, for the treatment of PD.

  12. Surfactant-induced non-lethal release of anthraquinones from suspension culture of Morinda citrifolia.

    NARCIS (Netherlands)

    Bassetti, L.; Hagendoorn, M.J.M.; Tramper, J.

    1995-01-01

    A new approach based on the use of the surfactant Pluronic F-68 to obtain non-lethal release of plant cell intracellular products was investigated. Suspension cultures of Morinda citrifolia (Rubiaceae), producing anthraquinones as secondary metabolites, were selected as model system. By supplementin

  13. Surfactant-induced non-lethal release of anthraquinones from suspension culture of Morinda citrifolia.

    NARCIS (Netherlands)

    Bassetti, L.; Hagendoorn, M.J.M.; Tramper, J.

    1995-01-01

    A new approach based on the use of the surfactant Pluronic F-68 to obtain non-lethal release of plant cell intracellular products was investigated. Suspension cultures of Morinda citrifolia (Rubiaceae), producing anthraquinones as secondary metabolites, were selected as model system. By

  14. Electrospinning synthesis of porous Al{sub 2}O{sub 3} nanofibers by pluronic P123 triblock copolymer surfactant and properties of uranium (VI)-sorption

    Energy Technology Data Exchange (ETDEWEB)

    Ren, Bo [The Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, Harbin 150001 (China); Department of Applied Chemistry Engineering, Jilin Vocational College of Industry and Technology, Jilin 132013 (China); Institute of Petrochemistry Heilongjiang Academy of Sciences, Harbin 150001 (China); Fan, Meiqing [The Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, Harbin 150001 (China); Department of Applied Chemistry Engineering, Jilin Vocational College of Industry and Technology, Jilin 132013 (China); Tan, Lichao [The Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, Harbin 150001 (China); Li, Rumin, E-mail: lirumin@hrbeu.edu.cn [The Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, Harbin 150001 (China); Song, Dalei; Liu, Qi [The Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, Harbin 150001 (China); Wang, Jun, E-mail: zhqw1888@sohu.com [The Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, Harbin 150001 (China); Institute of Advanced Marine Materials, Harbin Engineering University, Harbin 150001 (China); Zhang, Bin [Institute of Petrochemistry Heilongjiang Academy of Sciences, Harbin 150001 (China); Jing, Xiaoyan [The Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, Harbin 150001 (China)

    2016-07-01

    Porous Alumina (Al{sub 2}O{sub 3}) nanofibers were prepared by electrospinning process using pluronic P123 triblock copolymer surfactant as template. The characterizations of the adsorbent were investigated by X-ray diffraction (XRD) fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and nitrogen adsorption–desorption. The obtained nanofibers were used as adsorbents for the removal of Uranium (VI). The maximum adsorption occurred at pH 5, the equilibrium adsorption amount was about 87 mg/g, and the equilibrium time was 6.0 h. A pseudo-second order model could best describe adsorption kinetics. The adsorption equilibrium data fit Freundlich adsorption isotherm equation well. Thermodynamic parameters such as standard enthalpy (ΔH{sup 0}), standard entropy (ΔS{sup 0}), standard free energy (ΔG{sup 0}) and activation energy (E{sub a}) were calculated. The results predict an endothermic nature of adsorption and a spontaneous process. - Highlights: • The porous Al{sub 2}O{sub 3} nanofibers were used for U(VI)-sorption for the first time. • The adsorption process was endothermic and spontaneous. • The maximum adsorption capacity was 87 mg g{sup −1} at 25 °C.

  15. Improving emulsification efficacy of lecithin by formulation design. I: Effect of adding a secondary surfactant.

    Science.gov (United States)

    Krishna, G; Wood, G C; Sheth, B B

    1998-01-01

    The objective of this study was to seek improvement in the emulsification efficacy of lecithin by formulation design. A Base Emulsion was developed containing lecithin as the primary emulsifier. The lecithin concentration and method of preparation of the Base Emulsion were optimized to obtain minimum particle size and creaming of the emulsion. Selected hydrophilic and hydrophobic synthetic surfactants were evaluated as secondary emulsifiers for their ability to reduce particle size of the Base Emulsion. The selection of type and concentration of the secondary emulsifier was done by application of the HLB method. The hydrophilic emulsifiers selected were Tween 80, Tween 20, Pluronic F68, and Pluronic F127. The hydrophobic surfactants studied included Span 20, Span 80, Pluronic P103, and Pluronic P123. The median droplet size of the Base Emulsion was 2.7 microns. Addition of the hydrophilic emulsifiers caused an increase in particle size and substantial creaming of the emulsions. Addition of three of four hydrophobic surfactants resulted in particle size reduction, but the emulsions showed substantial creaming. Span 20 was found to be the most effective secondary emulsifier. The median particle size of the emulsion was 1.7 microns. These results suggest that supplementing the hydrophilic attributes of lecithin with an appropriate type and amount of hydrophobic surfactant improves the emulsion properties by applying principles of formulation design.

  16. A small angle neutron scattering study on the mixtures of pluronic L121 and anionic surfactant AOT

    Indian Academy of Sciences (India)

    G Ghosh; V K Aswal; D Varade

    2008-11-01

    Small angle neutron scattering (SANS) experiments have been carried out on the micellar solutions containing mixtures of a hydrophobic triblock copolymer (L121, EO5PO68EO5) and a hydrophobic anionic surfactant (AOT, sodium bis(2-ethylhexyl)sulphosuccinate) in water with varying ratio () of AOT to L121 for = 0.15, 0.2, 0.3, 0.5 and 0.6. It is known that either L121 or AOT alone forms vesicles in water, but in the mixture with appropriate ratio of the two components a thermodynamically stable, isotropic solution of apparently small micelle-like aggregates is formed. We find that these micelles are prolate ellipsoidal.

  17. Effect of F68 on cryopreservation of mesenchymal stem cells derived from human tooth germ.

    Science.gov (United States)

    Doğan, Ayşegül; Yalvaç, Mehmet Emir; Yılmaz, Aysu; Rizvanov, Albert; Sahin, Fikrettin

    2013-12-01

    The use of stem-cell-based therapies in regenerative medicine and in the treatment of disorders such as Parkinson, Alzheimer's disease, diabetes, spinal cord injuries, and cancer has been shown to be promising. Among all stem cells, mesenchymal stem cells (MSCs) were reported to have anti-apoptotic, immunomodulatory, and angiogenic effects which are attributed to the restorative capacity of these cells. Human tooth germ stem cells (HTGSCs) having mesenchymal stem cell characteristics have been proven to exert high proliferation and differentiation capacity. Unlike bone-marrow-derived MSCs, HTGSCs can be easily isolated, expanded, and cryopreserved, which makes them an alternative stem cell source. Regardless of their sources, the stem cells are exposed to physical and chemical stresses during cryopreservation, hindering their therapeutic capacity. Amelioration of the side effects of cryopreservation on MSCs seems to be a priority in order to maximize the therapeutic efficacy of these cells. In this study, we tested the effect of Pluronic 188 (F68) on HTGSCs during long-term cryopreservation and repeated freezing and defrosting cycles. Our data revealed that F68 has a protective role on survival and differentiation of HTGSCs in long-term cryopreservation.

  18. Effect of surfactant and oil additions in the biodegradation of hexane and toluene vapours in batch tests.

    Science.gov (United States)

    Galindo, H; Revah, S; Cervantes, F J; Arriaga, S

    2011-01-01

    The biological treatment of gaseous emissions of hydrophobic volatile organic compounds (VOCs) results in low rates of elimination partially because of the low solubility of VOCs in water. Recently, the use of two-phase partition bioreactors (TPPBs) was proposed to increase the bioavailability and consequently the elimination capacities of this kind of VOC. In the present study, TPPBs operating in a batch feed mode were tested for biodegradation of hexane and toluene vapours with a microbial consortium. The results obtained were compared with single-phase systems (control experiments). The liquid phase used was silicone oil (organic phase) with the surfactant Pluronic F-68. Experiments were named F1 and F2 for one and two phases, respectively, and F(1S) and F(2S) when the surfactant was included. The maximum specific rates (S(rates)) of hydrocarbon consumption for hexane and toluene were 539 and 773 mg(hydrocarbon)/(g(protein) x h), respectively. For both substrates, the systems that showed the highest S(rates) of hydrocarbon consumption were F2 and F(2S). In experiment F(1S) the surfactant Pluronic F-68 increased the solubility of hydrocarbons in the liquid phase, but did not increase the S(rates). The maximum percentages of mineralization were 51% and 72% for hexane and toluene, respectively. The results showed that simultaneous addition of silicone oil and surfactant favours the mineralization, but not the rate ofbiodegradation, of toluene and hexane vapours.

  19. Rheology of cellulose nanofibrils in the presence of surfactants.

    Science.gov (United States)

    Quennouz, Nawal; Hashmi, Sara M; Choi, Hong Sung; Kim, Jin Woong; Osuji, Chinedum O

    2016-01-07

    Cellulose nanofibrils (CNFs) present unique opportunities for rheology modification in complex fluids. Here we systematically consider the effect of ionic and non-ionic surfactants on the rheology of dilute CNF suspensions. Neat suspensions are transparent yield-stress fluids which display strong shear thinning and power-law dependence of modulus on concentration, G' ∼ c(2.1). Surfactant addition below a critical mass concentration cc produces an increase in the gel modulus with retention of optical clarity. Larger than critical concentrations induce significant fibril aggregation leading to the loss of suspension stability and optical clarity, and to aggregate sedimentation. The critical concentration was the lowest for a cationic surfactant (DTAB), cc ≈ 0.08%, while suspension stability was retained for non-ionic surfactants (Pluronic F68, TX100) at concentrations up to 8%. The anionic surfactant SDS led to a loss of stability at cc ≈ 1.6% whereas suspension stability was not compromised by anionic SLES up to 8%. Dynamic light scattering data are consistent with a scenario in which gel formation is driven by micelle-nanofibril bridging mediated by associative interactions of ethoxylated surfactant headgroups with the cellulose fibrils. This may explain the strong difference between the properties of SDS and SLES-modified suspensions. These results have implications for the use of CNFs as a rheology modifier in surfactant-containing systems.

  20. A conductometric investigation of hydroxypropylmethyl cellulose/sodium dodecyl sulfate/nonionic surfactant systems

    Directory of Open Access Journals (Sweden)

    Petrović Lidija B.

    2014-01-01

    Full Text Available Surfactant mixtures are very often used in various cosmetic and pharmaceutical products because they commonly act in synergism and provide more favorable properties than the single surfactants. At the same time, the 9 presence of polymers in mixtures of surfactants may lead to molecular interactions thereby affecting product stability and activity. For these reasons it is very important to determine the surfactant interactions influence on 1micellization and mixed micellization, as well as polymer-surfactants mixed micelles interactions. In this work we examined self-aggregation of nonionic surfactants, polysorbate 20 (Tween 20, polyoxyethylene octylphenyl ether (Triton X100 and polyoxyethylene-polyoxypropylene block copolymer (Pluronic F68 with ionic surfactant, sodium dodecylsulfate, in aqueous solution at 40ºC using conductometric titration method. It was found that concentration region for mixed micelle formation depends on nonionic surfactant characteristics and its concentration. Formation of surfactants mixed micelles in the presence of nonionic polymer, hydroxypropylmethyl cellulose, and their binding to polymer hydrophobic sites, were investigated too. Analysis of obtained results points to different kinds of interactions in investigated systems, which are crucial for their application. [Projekat Ministarstva nauke Republike Srbije, br. III 46010

  1. Improving pure red upconversion emission of Co-doped Y{sub 2}O{sub 3}:Yb{sup 3+}–Er{sup 3+} nanocrystals with a combination of sodium sulfide and surfactant Pluronic-F127

    Energy Technology Data Exchange (ETDEWEB)

    López-Luke, T., E-mail: tzarara@cio.mx [Centro de Investigaciones en Óptica, A.P. 1-948, León, Gto. 37160, México (Mexico); De la Rosa, E., E-mail: elder@cio.mx [Centro de Investigaciones en Óptica, A.P. 1-948, León, Gto. 37160, México (Mexico); Campos Villalobos, I. [Centro de Investigaciones en Óptica, A.P. 1-948, León, Gto. 37160, México (Mexico); Rodriguez, R.A. [Universidad de Guadalajara, Unidad Lagos, Lagos de Moreno, Jal. 47460, México (Mexico); Ángles-Chávez, C. [Instituto Mexicano del Petróleo, Cd. México, D.F. 07730, México (Mexico); Salas, P. [Centro de Física Aplicada y Tecnología Avanzada, Universidad Nacional Autónoma de México, A.P. 1-1010, Querétaro, Qro. 76000, México (Mexico); Wheeler, Damon A.; Zhang, J.Z. [Department of Chemistry and Biochemistry, University of California, Santa Cruz, CA 95064 (United States)

    2014-01-15

    Nanocrystals of Y{sub 2}O{sub 3}:Yb{sup 3+}–Er{sup 3+} (2:1 mol% Yb{sup 3+}:Er{sup 3+}) were prepared by a novel precipitation technique using Na{sub 2}S and Pluronic-F127 (PF127) surfactant. Crystal structure, particle size, red emission intensity and fluorescence decay lifetimes were determined using microscopy and spectroscopy techniques. TEM analysis indicates that the average particle size ranged from 40 to 70 nm. The nanocrystals showed a strong red emission band centered at 663 nm after excitation at 970 nm. The upconverted signal intensity was improved 250% with an optimum concentration of Na{sub 2}S (0.48 M) and PF127 (0.1 mM). The improvement was explained in terms of the reduction of surface contaminants as well as the cubic crystalline phase of the parent Y{sub 2}O{sub 3} material. Interestingly, the formation of sulfates (SO{sub 4}{sup 2−}) is faster than that of O–H, which is responsible for quenching the red and green emissions. The results suggest that Na{sub 2}S and PF127 are good candidates for surface passivation, especially when used in conjunction. The preparation of Y{sub 2}O{sub 3}:Yb{sup 3+}–Er{sup 3+} using Na{sub 2}S with strong red emission band was produced at a lower cost than that of other sulfuration processes. -- Highlights: • . • Strong red emission band centered at 663 nm was obtained after excitation at 970 nm. • Yb-Er codoped Y2O3 nanocrystals with average size ranging from 40 to 70 nm. • Improvement of the red emission in Y2O3:Yb-Er nanocrystals by the introduction of sodium sulfide and pluronic. • Passivation of nanocrystal surface with sodium sulfide and pluoronic.

  2. Gelation kinetics and viscoelastic properties of pluronic and α-cyclodextrin-based pseudopolyrotaxane hydrogels.

    Science.gov (United States)

    Pradal, Clementine; Jack, Kevin S; Grøndahl, Lisbeth; Cooper-White, Justin J

    2013-10-14

    The results of a systematic investigation into the gelation behavior of α-cyclodextrin (α-CD) and Pluronic (poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) block copolymers) pseudopolyrotaxane (PPR) hydrogels are reported here in terms of the effects of temperature, α-CD concentration, and Pluronic type (Pluronic F68 and Pluronic F127). It was found that α-CD significantly modifies the gelation behavior of Pluronic solutions and that the PPR hydrogels are highly sensitive to changes in the α-CD concentration. In some cases, the addition of α-CD was found to be detrimental to the gelation process, leading to slower gelation kinetics and weaker gels than with Pluronic alone. However, in other cases, the hydrogels formed in the presence of the α-CDs reached higher moduli and showed faster gelation kinetics than with Pluronic alone and in some instances α-CD allowed the formation of hydrogels from Pluronic solutions that would normally not undergo gelation. Depending on composition and ratio of α-CD/Pluronic, these highly viscoelastic hydrogels displayed elastic shear modulus values ranging from 2 kPa to 7 MPa, gelation times ranging from a few seconds to a few hours and self-healing behaviors post failure. Using dynamic light scattering (DLS) and small-angle X-ray scattering (SAXS), we probed the resident structure of these systems, and from these insights we have proposed a new molecular mechanism that accounts for the macroscopic properties observed.

  3. Temperature-induced aggregation in aqueous solutions of pluronic F68 triblock copolymer containing small amount of o-xylene

    DEFF Research Database (Denmark)

    Borbely, S.; Pedersen, J.S.

    2000-01-01

    The temperature- and concentration-dependent aggregation of EO(78)PO(30)EO(78) triblock copolymer in aqueous solutions has been studied in the concentration range from 5 to 200 g/dm(3) at 25 degrees C, 45 degrees C and 60 degrees C. The influence of o-xylene on the micellization was measured at v...... at various (from 5 to 40) molar ratio of additive to polymer. The aggregates were described as polydisperse spheres with tethered Gaussian polymer chains. The results of the least-squares fit is briefly discussed. (C) 2000 Elsevier Science B.V. All rights reserved....

  4. Surfactant-assisted dispersion of carbon nanotubes: mechanism of stabilization and biocompatibility of the surfactant

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Raman Preet, E-mail: ramanpreetsingh@hotmail.com [Evalueserve SEZ (Gurgaon) Pvt. Ltd. (India); Jain, Sanyog [National Institute of Pharmaceutical Education and Research, Centre for Pharmaceutical Nanotechnology, Department of Pharmaceutics (India); Ramarao, Poduri, E-mail: ramaraop@yahoo.com [Central University of Punjab, School of Basic and Applied Sciences (India)

    2013-10-15

    Nanoparticles (NPs) are thermodynamically unstable system and tend to aggregate to reduce free energy. The aggregation property of NPs results in inhomogeneous exposure of cells to NPs resulting in variable cellular responses. Several types of surfactants are used to stabilize NP dispersions and obtain homogenous dispersions. However, the effects of these surfactants, per se, on cellular responses are not completely known. The present study investigated the application of Pluronic F68 (PF68) for obtaining stable dispersion of NPs using carbon nanotubes as model NPs. PF68-stabilized NP suspensions are stable for long durations and do not show signs of aggregation or settling during storage or after autoclaving. The polyethylene oxide blocks in PF68 provide steric hindrance between adjacent NPs leading to stable NP dispersions. Further, PF68 is biocompatible in nature and does not affect integrity of mitochondria, lysosomes, DNA, and nuclei. Also, PF68 neither induce free radical or cytokine production nor does it interfere with cellular uptake mechanisms. The results of the present study suggest that PF68-assisted dispersion of NPs produced suspensions, which are stable after autoclaving. Further, PF68 does not interfere with normal physiological functions suggesting its application in nanomedicine and nanotoxicity evaluation.

  5. Pluronic lecithin organogel

    Directory of Open Access Journals (Sweden)

    Belgamwar Veena

    2008-01-01

    Full Text Available The purpose of this review is to give detail insight of pluronic lecithin organogels (PLOs as a topical and transdermal drug delivery system. Pluronic lecithin organogel is a microemulsion-based gel that has been effectively used by physicians and pharmacists to deliver hydrophilic and lipophilic drugs topically and transdermally across the stratum corneum. It is thermodynamically stable, viscoelastic, and biocompatible gel composed of phospholipids (lecithin, organic solvent, and polar solvent. Various types of therapeutic agents have been easily incorporated in PLO to improve their topical drug delivery. Pluronic lecithin organogel improves the topical administration of drug mainly because of desired drug partitioning, biphasic drug solubility, and the modification of skin barrier system by organogel components. Beside this, it shows low skin irritation, increases patient compliance, reduces side effects, avoids first pass metabolism, and increases efficiency of drug. In addition, PLO has been shown in vivo and in vitro to modulate the release and permeation of drugs applied transdermally. Thus, in future, it has wide range of applications and opportunities to experiment with various drugs in this type of drug delivery system.

  6. Preparation of Stable Solid Lipid Nanoparticles (SLNs) Suspension with Combined Surfactants%表面活性剂复配制备稳定的固体脂质纳米粒混悬液

    Institute of Scientific and Technical Information of China (English)

    侯冬枝; 谢长生; 平其能

    2005-01-01

    目的:表面活性剂在固体脂质纳米粒的制备过程中扮演着重要角色,为规避药物对体系的影响,本文选用4种表面活性剂制备了空白而具有良好物理稳定性的固体脂质纳米粒混悬液.方法:用激光散射粒度仪和Zeta电位分析仪(LD)检测平均粒径、颗粒分布范围和Zeta电位,另外还进行了DSC热分析和颗粒形态的TEM观察.结果:离子型表面活性剂脱氧胆酸钠可以提高纳米粒的Zeta电位从而提高系统物理稳定性,但乳化率低;非离子乳化剂Pluronic F-68可以起到空间稳定的作用从而避免胶体系统中颗粒的聚结.结论:4种表面活性剂的复配[两种非离子乳化剂(Pluronic F-68和Tween 80),离子型表面活性剂(脱氧胆酸钠)以及卵磷脂]可以制备稳定6个月而不分层的纳米混悬液.%AIM:Surfactants and their blend play important roles in the preparation of solid lipid nanoparticles (SLNs).In this study,four types of surfactant were employed to investigate the influence of the surfactants on properties of SLNs in the absence of model drugs thereby avoiding the interaction between the surfactant and the drug.METHODS:The physicochemical properties of the colloidal systems,such as mean particle size,distribution range and Zeta potential,were investigated by laser diffractometry and the DSC analysis was performed as well.RESULTS:It was found that ionic surfactants,such as sodium deoxycholate, increased the Zeta potential of nanoparticles leading to improve the physical stability of the system.But it showed obviously relative low emulsification efficiency in the preparation.Non-ionic emulsifier,especially Pluronic F-68, offered additional steric stabilization effect avoiding aggregation of the fine particles in the colloidal system.CONCLUSION:The formulation in the study for the first time combined four types of additives including ionic surfactant (sodium deoxycholate),non-ionic emulsifier (Pluronic F-68 and Tween-80),and

  7. Micellar Packing in Aqueous Solutions of As-Received and Pure Pluronic Block Copolymers

    Science.gov (United States)

    Ryu, Chang; Park, Han Jin

    2013-03-01

    Pluronic block copolymers (Pluronics) are produced on a commercial scale to enable wide range of novel applications from emulsification and colloidal stabilization as nonionic surfactants. While the Pluronic block copolymers offer the advantages of being readily available for such applications, it contains non-micellizable low molecular weight (MW) impurities that would interfere with the self-assembly and micellar packing of PEO-PPO-PEO triblock copolymers in aqueous solutions. The impacts of the low MW impurities will be discussed on the micellar packing of Pluronics F108 and F127 solutions, which form BCC and FCC. While as-received Pluronic samples typically contain about 20 wt.% low MW impurities, we were able to reduce the impurity level to less than 2 wt.% using our large scale purification technique. Comparative studies on small angle x-ray scattering (SAXS) experiments on as-received and purified Pluronics solutions revealed that the contents of triblock copolymers in solutions essentially governs the inter-micellar distance of Pluronic cubic structures. A universal relationship between triblock copolymer concentration and SAXS-based domain spacing has been finally discussed. Funding from Agency for Defense Development, Korea.

  8. Use of surfactants as plasticizers in preparing solid dispersions of poorly soluble API: selection of polymer-surfactant combinations using solubility parameters and testing the processability.

    Science.gov (United States)

    Ghebremeskel, Alazar N; Vemavarapu, Chandra; Lodaya, Mayur

    2007-01-10

    Formation of solid dispersions as a means to enhance the dissolution rate of poorly soluble Active pharmaceutical ingredients (APIs) typically employs hydrophilic polymer systems and surfactants. While the utility of the surfactant systems in solubilization is well known, the secondary effects of the same on processing and subsequent physical stability of the solid dispersions needs to be studied further. Physical blends of the poorly soluble API and hydrophilic polymers such as PVP-K30, Plasdone-S630, HPMC-E5, HPMCAS, and Eudragit L100 with mass ratio 1:1 were prepared. The surfactants tested in this study included Tween-80, Docusate sodium, Myrj-52, Pluronic-F68 and SLS. Thermal analysis of the API-polymer-surfactant blends suggested that the surfactants caused solvation/plasticization, manifesting in reduction of (i) the melting (T(m)) of API (ii) T(g) of the polymers and (iii) the combined T(g) of the solid dispersion formed from quench cooling. Explanation of these effects of surfactants is attempted based on their physical state (at the temperature of interest), HLB values and similarity of their solubility parameter values with respect to drug-polymer systems. Furthermore, extruded matrices containing different API-polymer (PVP-K30, Plasdone-S630, and HPMC-E5) mixtures prepared with and without surfactants, were produced by feeding the powder blend through a hot-melt extruder. The melt viscosity of the polymer blends was assessed by torque rheometry using a Haake Rheomix. The physicochemical properties of the extruded API-polymer-surfactant were characterized by differential scanning calorimetry, X-ray diffraction, Raman spectroscopy, and polarized microscopy. The results demonstrated that the glass transition temperature of the carrier polymers decreased as direct result of the surfactants in the extrudate, due to an increase in the chain mobility of polymers. A decrease in the melt viscosity was seen due to a plasticization of the polymer. The drug release

  9. Plasma membrane ordering agent pluronic F-68 (PF-68) reduces neurotransmitter uptake and release and produces learning and memory deficits in rats

    Science.gov (United States)

    Clarke, M. S.; Prendergast, M. A.; Terry, A. V. Jr

    1999-01-01

    A substantial body of evidence indicates that aged-related changes in the fluidity and lipid composition of the plasma membrane contribute to cellular dysfunction in humans and other mammalian species. In the CNS, reductions in neuronal plasma membrane order (PMO) (i.e., increased plasma membrane fluidity) have been attributed to age as well as the presence of the beta-amyloid peptide-25-35, known to play an important role in the neuropathology of Alzheimer's disease (AD). These PMO increases may influence neurotransmitter synthesis, receptor binding, and second messenger systems as well as signal transduction pathways. The effects of neuronal PMO on learning and memory processes have not been adequately investigated, however. Based on the hypothesis that an increase in PMO may alter a number of aspects of synaptic transmission, we investigated several neurochemical and behavioral effects of the membrane ordering agent, PF-68. In cell culture, PF-68 (nmoles/mg SDS extractable protein) reduced [3H]norepinephrine (NE) uptake into differentiated PC-12 cells as well as reduced nicotine stimulated [3H]NE release. The compound (800-2400 microg/kg, i.p., resulting in nmoles/mg SDS extractable protein in the brain) decreased step-through latencies and increased the frequencies of crossing into the unsafe side of the chamber in inhibitory avoidance training. In the Morris water maze, PF-68 increased the latencies and swim distances required to locate a hidden platform and reduced the time spent and distance swam in the previous target quadrant during transfer (probe) trials. PF-68 did not impair performance of a well-learned working memory task, the rat delayed stimulus discrimination task (DSDT), however. Studies with 14C-labeled PF-68 indicated that significant (pmoles/mg wet tissue) levels of the compound entered the brain from peripheral (i.p.) injection. No PF-68 related changes were observed in swim speeds or in visual acuity tests in water maze experiments, rotorod performance, or in tests of general locomotor activity. Furthermore, latencies to select a lever in the DSDT were not affected. These results suggest that PF-68 induced deficits in learning and memory without confounding peripheral motor, sensory, or motivational effects at the tested doses. Furthermore, none of the doses induced a conditioned taste aversion to a novel 0.1% saccharin solution indicating a lack of nausea or gastrointestinal malaise induced by the compound. The data indicate that increases in neuronal plasma membrane order may have significant effects on neurotransmitter function as well as learning and memory processes. Furthermore, compounds such as PF-68 may also offer novel tools for studying the role of neuronal PMO in mnemonic processes and changes in PMO resulting from age-related disorders such as AD.

  10. Role of hydration and water coordination in micellization of Pluronic block copolymers.

    Science.gov (United States)

    Šturcová, Adriana; Schmidt, Pavel; Dybal, Jiří

    2010-12-15

    Raman, attenuated total reflectance FTIR, near-infrared spectroscopy, and DFT calculations have been used in a study of aqueous solutions of three tri-block copolymers poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) or PEO-PPO-PEO with commercial names Pluronic PE6200, PE6400 and F68. It is shown that the process of micellization as a response to increased temperature is reflected in the hydroxyl stretching region of infrared and Raman spectra, which contains information both about restructuring of water and changes of polymer chains in polymer/water aggregates. Raman spectra exhibit differences between individual Pluronics even at temperatures below the critical micellization temperature (CMT). According to the attenuated total reflection (ATR) FTIR spectra, the same five water coordination types defined by the number of donated/accepted hydrogen bonds are present in interacting water as in bulk water. It indicates that models considering mixed states of water with different hydrogen bonding environments provide appropriate descriptions of bound water both below and above the CMT. Above the CMT, aggregate hydration increases in the order PE6400 < PE6200 < F68, although that does not fully correspond to the EO/PO ratio, and points to the differences in microstructure of aggregates formed by each copolymer. This study relates nanoscale phenomena (hydrophobic and hydrophilic hydration) with the mesoscale phenomenon of micellization. Copyright © 2010 Elsevier Inc. All rights reserved.

  11. Lung deposition and toxicological responses evoked by multi-walled carbon nanotubes dispersed in a synthetic lung surfactant in the mouse.

    Science.gov (United States)

    Ronzani, Carole; Spiegelhalter, Coralie; Vonesch, Jean-Luc; Lebeau, Luc; Pons, Françoise

    2012-01-01

    In the present work, we elaborated a synthetic lung surfactant composed of dipalmitoyl phosphatidylcholine (DPPC), phosphatidylglycerol, cholesterol and bovine serum albumin (BSA), as a vehicle to study the lung toxicity of pristine multi-walled carbon nanotubes (MWCNT). MWCNT were dispersed in surfactant, saline or saline containing DPPC, BSA, Pluronic(®) F68 or sodium dodecyl sulfate, for comparison. Dispersions were characterized visually, and by light microscopy, dynamic light scattering and transmission electronic microscopy (TEM). Deposition of surfactant-dispersed MWCNT in the lung of BALB/c mice upon single or repeated administrations was analyzed by histology and TEM. Inflammation and airway remodeling were assessed in bronchoalveolar lavage fluid (BALF) or lung tissue of mice by counting cells and quantifying cytokines, tumor growth factor (TGF)-β1 and collagen, and by histology. We found that the elaborated surfactant is more effective in dispersing MWCNT when compared to the other agents, while being biocompatible. Surfactant-dispersed MWCNT distributed all throughout the mouse airways upon single and repeated administrations and were observed in alveolar macrophages and epithelial cells, and in infiltrated neutrophils. Mice that received a single administration of MWCNT showed neutrophil infiltrate and greater concentrations of tumor necrosis factor (TNF)-α, keratinocyte-derived chemokine (KC) and interleukin (IL)-17 in BALF when compared to controls. After repeated MWCNT administrations, increases in macrophage number, KC and TGF-β1 levels in BALF, and collagen deposition and mucus hyperplasia in lung tissue were observed. Altogether, the elaborated lung surfactant could be a valuable tool to further study the toxicological impact of pristine MWCNT in laboratory animals.

  12. Boron and Poloxamer (F68 and F127) Containing Hydrogel Formulation for Burn Wound Healing.

    Science.gov (United States)

    Demirci, Selami; Doğan, Ayşegül; Karakuş, Emre; Halıcı, Zekai; Topçu, Atila; Demirci, Elif; Sahin, Fikrettin

    2015-11-01

    Burn injuries, the most common and destructive forms of wounds, are generally accompanied with life-threatening infections, inflammation, reduced angiogenesis, inadequate extracellular matrix production, and lack of growth factor stimulation. In the current study, a new antimicrobial carbopol-based hydrogel formulated with boron and pluronic block copolymers was evaluated for its healing activity using in vitro cell culture techniques and an experimental burn model. Cell viability, gene expression, and wound healing assays showed that gel formulation increased wound healing potential. In vitro tube-like structure formation and histopathological examinations revealed that gel not only increased wound closure by fibroblastic cell activity, but also induced vascularization process. Moreover, gel formulation exerted remarkable antimicrobial effects against bacteria, yeast, and fungi. Migration, angiogenesis, and contraction-related protein expressions including collagen, α-smooth muscle actin, transforming growth factor-β1, vimentin, and vascular endothelial growth factor were considerably enhanced in gel-treated groups. Macrophage-specific antigen showed an oscillating expression at the burn wounds, indicating the role of initial macrophage migration to the wound site and reduced inflammation phase. This is the first study indicating that boron containing hydrogel is able to heal burn wounds effectively. The formulation promoted burn wound healing via complex mechanisms including stimulation of cell migration, growth factor expression, inflammatory response, and vascularization.

  13. Study of Low Molecular Weight Impurities in Pluronic Triblock Copolymers using MALDI, Interaction Chromatography, and NMR

    Science.gov (United States)

    Helming, Z.; Zagorevski, D.; Ryu, C. Y.

    2014-03-01

    Poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) triblock copolymers are a group of commercial macromolecular amphiphilic surfactants that have been widely studied for their applications in polymer-based nanotechnology and drug-delivery. It has been well-established that the synthesis of commercial Pluronic triblocks results in low molecular weight ``impurities,'' which are generally disregarded in the applications and study of these polymers. These species have been shown to have significant effects on the rheological properties of the material, as well as altering the supramolecular ``micellar'' structures for which the polymers are most often used. We have isolated the impurities from the bulk Pluronic triblock using Interaction Chromatography (IC) techniques, and subjected them to analysis by H1 NMR and MALDI (Matrix-Assisted Laser Desorption Ionization) Mass Spectrometry to identify relative block composition and molecular weight information. We report significant evidence of at least two polymeric components: a low-molecular-weight homopolymer of poly(ethylene oxide) and a ``blocky'' copolymer of both poly(ethylene oxide) and poly(propylene oxide). This has significant implications, not only for the applied usage of Pluronic triblock copolymers, but for the general scientific acceptance of the impurities and their effects on Pluronic micelle and hydrogel formation.

  14. Electrochemical and SEM properties of Co2+ ion in hexagonal mesophase of pluronic lyotropic liquid crystal template

    Indian Academy of Sciences (India)

    I S El-Hallag

    2009-10-01

    The electrochemical and SEM properties of Co2+ ion in hexagonal mesophase of the pluronic lyotropic liquid crystal template are reported. The cyclic voltammetric studies evidenced the occurrence of two slow electron transfer reduction processes. Such a reaction presumably related to the reduction of Co2+ ion to Co metal. The hexagonal (H1) lyotropic liquid crystalline phases of P84 surfactant have been used to template the electrochemical deposition of nanostructured cobalt films as well as its uses as background electrolyte. Electrochemical studies show that these films have very high surface areas, which reveals that the deposited film exhibits promising properties. The electrode parameters of Co(II) ion in hexagonal meso phase of the lyotropic liquid crystal ternary system (pluronic P84/cobalt/-xylene) is determined using cyclic voltammetry, deduced convolutive voltammetry and chronoamperometry techniques. The morphology of nanostructured deposited films of Co2+ ion in pluronic lyotropic liquid crystal template was investigated via scanning electron microscopy (SEM) technique.

  15. Using Nonionic Surfactants for Production of Semiconductor-type Carbon Nanotubes by Gel-based Affinity Chromatography

    Directory of Open Access Journals (Sweden)

    Varun Shenoy Gangoli

    2014-07-01

    characterization of the particulate suspension. Semiconductor- type SWCNTs are recovered in solid form by evaporating the suspension fluid, and heating the dried sample in air to a temperature just above the Pluronic decomposition temperature. Using Pluronic and other nonionic-type surfactants can aid the scalability of the chromatographic production of semiconducting SWCNT samples.

  16. Test of Surfactant-Based Dermal Wound Cleansers on Sulfur Mustard-Exposed Human Keratinocytes in an In Vitro Wound Healing Model

    Science.gov (United States)

    2008-11-01

    hydroxide, NF added for pH adjustment. Ten and 20% Pluronic F-68 solutions in water were also tested in the model. Two-minute treatments were...Mumford JH, Carnes DL, Cochran DL. Characterization of proliferation and cellular wound fill in periodontal cells using an in vitro wound model. J

  17. Formulation of benzoporphyrin derivatives in Pluronics.

    Science.gov (United States)

    Chowdhary, Rubinah K; Chansarkar, Namrata; Sharif, Isha; Hioka, Noboru; Dolphin, David

    2003-03-01

    This study investigates the potential of Pluronics for the formulation of tetrapyrrole-based photosensitizers, with a particular focus on B-ring benzoporphyrin derivatives. The B-ring derivatives have a high tendency to aggregate in aqueous solutions, and this poses a significant formulation problem. Pluronics are ABA-type triblock copolymers composed of a central hydrophobic polypropylene oxide section with two hydrophilic polyethylene oxide sections of equal length at either end. Out of a range of different commercially available block copolymers studied, it was found that the longer the hydrophobic block, the better the stabilization of tetrapyrrolic drugs in monomeric form in aqueous suspensions. Of these the best performance was observed in the micelle-forming Pluronic P123. Micelle size determination by laser light scattering confirmed that particle size in stable Pluronic formulations was around 20 nm. Pluronics such as L122 formed emulsions spontaneously without the need for emulsion stabilizers; emulsions were highly stable at ambient temperatures over several days and also highly effective as potential drug delivery agents.

  18. Block copolymers of ethylene oxide and propylene oxide (pluronics) as immunomodulators and antitumour agents.

    Science.gov (United States)

    Topchieva, I N; Erokhin, V N; Osipova, S V; Khrutskaya, M M; Kupriyanova, T A; Bykovskaya, S N

    1991-01-01

    Block copolymers of ethylene oxide and propylene oxide (pluronics) are nontoxic water-soluble membranotropic surfactants available as polymers with various compositions, molecular masses, number, and arrangement of blocks. In vivo experiments are reported which demonstrate that these polymers and their functional derivatives stimulate the production of anti-sheep-erythrocyte antibodies in mice. The introduction of reactive (hydroperoxide) groups into the polymers by chemical modification or by solubilization of low-molecular-mass hydroperoxides alters the properties of these immunostimulators. In vitro experiments revealed that these modified polymers enhance the activity of natural killer cells without reducing their viability. It is proposed that the immunomodulatory properties of pluronics and their derivatives play an important role in the antitumour activity of these substances in vivo.

  19. Preparation and evaluation of tubular micelles of pluronic lecithin organogel for transdermal delivery of sumatriptan.

    Science.gov (United States)

    Agrawal, Varsha; Gupta, Vandana; Ramteke, Suman; Trivedi, Piyush

    2010-12-01

    The present work focuses on the preparation and evaluation of lecithin organogel system of thermoreversible polymer pluronic F127, which would enhance the stability and absorption of sumatriptan succinate across the skin. Formulations were developed with and without co-surfactant (pluronic F127). The prepared organogels were evaluated for its appearance, organoleptic characteristics, and feel upon application, homogeneity, occlusivenes, washability, pH, viscosity, spreadability, gel transition temperature of formulations. The formulations were also evaluated for drug content, in vitro drug diffusion properties and skin irritation testing. In vivo evaluation of formulations was carried out by hot plate and writhing test method, and finally the optimized formulation was subjected to stability studies. The developed formulations were easily washable, smooth in feel, and showed no clogging which indicate superior texture of system. Formulation, containing pluronic showed greater spreadability and higher drug diffusion rate as compared to pluronic free organogel. Drug content of organogel formulations was in the range of 94-97%. The pH of the formulations was 6.48 ± 0.5 and 6.98 ± 0.1, reflecting no risk of skin irritation. Pluronic not only enhances the stability of organogel by increasing the viscosity (from 6,541 ± 234.76 to 7,826 ± 155.65 poise) but also increases the release of drug from 67.39 ± 1.53% to 74.21 ± 1.7%. The sumatriptan exhibits higher and long lasting antinociceptive effect as indicated by the persistent increase in reaction time in hot plate and inhibited abdominal contraction in acetic acid-induced writhing test (p < 0.05). The prepared optimized formulation was found to be stable without any significant changes at room temperature.

  20. Differentiation of human stem cells is promoted by amphiphilic pluronic block copolymers

    Directory of Open Access Journals (Sweden)

    Doğan A

    2012-09-01

    Full Text Available Aysegül Doğan,1 Mehmet E Yalvaç,1,2 Fikrettin Şahin,1 Alexander V Kabanov,3–5 András Palotás,6 Albert A Rizvanov71Department of Genetics and BioEngineering, College of Engineering and Architecture, Yeditepe University, Istanbul, Turkey; 2Center for Gene Therapy, Nationwide Children's Hospital, Ohio State University, Columbus, OH, USA; 3Center for Drug Delivery and Nanomedicine, 4Department of Pharmaceutical Sciences, College of Pharmacy, Durham Research Center, University of Nebraska Medical Center, Omaha, NE, USA; 5Laboratory of Chemical Design of Bio-nano-materials, Department of Chemistry, Mikhail V Lomonosov Moscow State University, Moscow, Russia; 6Asklepios-Med, Szeged, Hungary; 7Institute of Fundamental Medicine and Biology, Kazan (Volga Region Federal University, Kazan, RussiaAbstract: Stem cell usage provides novel avenues of tissue regeneration and therapeutics across disciplines. Apart from ethical considerations, the selection and amplification of donor stem cells remain a challenge. Various biopolymers with a wide range of properties have been used extensively to deliver biomolecules such as drugs, growth factors and nucleic acids, as well as to provide biomimetic surface for cellular adhesion. Using human tooth germ stem cells with high proliferation and transformation capacity, we have investigated a range of biopolymers to assess their potential for tissue engineering. Tolerability, toxicity, and their ability to direct differentiation were evaluated. The majority of pluronics, consisting of both hydrophilic and hydrophobic poly(ethylene oxide chains, either exerted cytotoxicity or had no significant effect on human tooth germ stem cells; whereas F68 increased the multi-potency of stem cells, and efficiently transformed them into osteogenic, chondrogenic, and adipogenic tissues. The data suggest that differentiation and maturation of stem cells can be promoted by selecting the appropriate mechanical and chemical

  1. Pluronic-poly (acrylic acid)-cysteine/Pluronic L121 mixed micelles improve the oral bioavailability of paclitaxel.

    Science.gov (United States)

    Zhao, Yanli; Li, Yanli; Ge, Jianjun; Li, Na; Li, Ling-Bing

    2014-11-01

    The aim of the study is to synthesize a thiolated Pluronic copolymer, Pluronic-poly (acrylic acid)-cysteine copolymer, to construct a mixed micelle system with the Pluronic-poly (acrylic acid)-cysteine copolymer and Pluronic L121 (PL121) and to evaluate the potential of these mixed micelles as an oral drug delivery system for paclitaxel. Compared with Pluronic-poly (acrylic acid)-cysteine micelles, drug-loading capacity of Pluronic-poly (acrylic acid)-cysteine/PL121 mixed micelles was increased from 0.4 to 2.87%. In vitro release test indicated that Pluronic-poly (acrylic acid)-cysteine/PL121 mixed micelles exhibited a pH sensitivity. The permeability of drug-loaded micelles in the intestinal tract was studied with an in situ perfusion method in rats. The presence of verapamil and Pluronic both improved the intestinal permeability of paclitaxel, which further certified the inhibition effect of thiolated Pluronic on P-gp. In pharmacokinetic study, the area under the plasma concentration-time curve (AUC0→∞) of paclitaxel-loaded mixed micelles was four times greater than that of the paclitaxel solution (p cysteine/PL121 micelles were proven to be a potential oral drug delivery system for paclitaxel.

  2. Rheological, mucoadhesive and release properties of pluronic F-127 gel and pluronic F-127/polycarbophil mixed gel systems.

    Science.gov (United States)

    Tirnaksiz, F; Robinson, J R

    2005-07-01

    This study was designed to combine the mucoadhesive property of Noveon and the thermosensitive property of Pluronic F-127 into one gel system. A rheological study of Pluronic aqueous sols (10-35%), Noveon gels (0.5-2%) and of mixed gels containing Pluronic (10-17.5%) and polycarbophil (0.5-2.5%) was conducted at different temperatures (15-35 degrees C). The viscosity of Pluronic sols increased with an increase in temperature and the mixed gels had thermoreversible property. The viscosity of mixed gels was higher than that of the Pluronic sols containing only Pluronic because of the increase in total polymer concentration. No interaction was found between -COOH groups of Noveon and Pluronic molecules at the studied concentrations of polymers; the viscosity of mixed gels containing un-neutralized Noveon was lower than that of the neutralized mixed gels. The effect of Pluronic F-127 on the mucoadhesive property of Noveon was investigated. The mucoadhesive properties of Pluronic and Noveon gels were compared by a force of detachment test. It was found that Pluronic and Noveon gels showed approximately the same mucoadhesive strength. However, there were significant differences in the viscosity of Noveon and Pluronic gels. The adhesive force of the mixed gel was almost same as that of the Noveon gel. The Pluronic did not affect the adhesive power of Noveon and the increased viscosity did not affect the bioadhesive force of the mixed gels. In spite of increasing viscosity of the gel, the percentage of released model material (mannitol) increased with increasing temperature. This is based on the previously reported observation that the interaction between the Pluronic molecules squeezed mannitol molecules out of the polymer chains. The mannitol release obeyed zero-order kinetics and the flux values of mixed gels at 15 and 35 degrees C were very similar. The Noveon chains among Pluronic chains probably hindered the diffusion of mannitol molecules and the release was thus

  3. Nanostructured Pluronic hydrogels as bioinks for 3D bioprinting.

    Science.gov (United States)

    Müller, Michael; Becher, Jana; Schnabelrauch, Matthias; Zenobi-Wong, Marcy

    2015-08-11

    Bioprinting is an emerging technology in the field of tissue engineering as it allows the precise positioning of biologically relevant materials in 3D, which more resembles the native tissue in our body than current homogenous, bulk approaches. There is however a lack of materials to be used with this technology and materials such as the block copolymer Pluronic have good printing properties but do not allow long-term cell culture. Here we present an approach called nanostructuring to increase the biocompatibility of Pluronic gels at printable concentrations. By mixing acrylated with unmodified Pluronic F127 it was possible to maintain the excellent printing properties of Pluronic and to create stable gels via UV crosslinking. By subsequent elution of the unmodified Pluronic from the crosslinked network we were able to increase the cell viability of encapsulated chondrocytes at day 14 from 62% for a pure acrylated Pluronic hydrogel to 86% for a nanostructured hydrogel. The mixed Pluronic gels also showed good printability when cells where included in the bioink. The nanostructured gels were, with a compressive modulus of 1.42 kPa, mechanically weak, but we were able to increase the mechanical properties by the addition of methacrylated hyaluronic acid. Our nanostructuring approach enables Pluronic hydrogels to have the desired set of properties in all stages of the bioprinting process.

  4. Pluronic-encapsulated natural chlorophyll nanocomposites for in vivo cancer imaging and photothermal/photodynamic therapies.

    Science.gov (United States)

    Chu, Maoquan; Li, Haikuo; Wu, Qiang; Wo, Fangjie; Shi, Donglu

    2014-09-01

    A great challenge in developing nanotechnologies for cancer diagnosis and therapy has been the combined functionalities required for complicated clinical procedures. Among all requirements, toxicity has been the major hurdle that has prevented most of the nano-carriers from clinical use. Here, we extracted chlorophyll (Chl) from vegetable and encapsulated it into polymer (pluronic F68, Plu) micelles for cancer imaging and therapy. The results showed that the Chl-containing nanocomposites were capable of mouse tumor targeting, and the nanocomposite fluorescence within the tumor sites remained at high intensity more than two days after tail-vein injection. It is interesting that oral administration with the nanocomposites was also successful for tumor target imaging. Furthermore, the dietary Chl was found to be able to efficiently convert near-infrared laser irradiation to heat. The growths of melanoma cells and mouse tumors were effectively inhibited after being treated with the nanocomposites and irradiation. The suppression of the tumors was achieved by laser-triggered photothermal and photodynamic synergistic effects of Chl. As a natural substance from vegetable, Chl is non-toxic, making it an ideal nano-carrier for cancer diagnosis and treatment. Based on the results of this research, the Plu-Chl nanocomposites have shown promise for future clinical applications.

  5. Surfactant effect on the conductivity behavior of CsH{sub 2}PO{sub 4}: Characterization by electrochemical impedance spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Hosseini, S., E-mail: Soraya@eng.ukm.m [Department of Chemical and Environmental Engineering, University Putra Malaysia, 43400 UPM Serdang, Selangor (Malaysia); Homaiee, M. [Department of Physics, University Putra Malaysia, 43400 UPM Serdang, Selangor (Malaysia); Mohamad, A.B. [Institute of Fuel Cell, University Kebangsaan Malaysia, 43600 Bangi, Selangor (Malaysia); Malekbala, M.R. [Department of Chemical and Environmental Engineering, University Putra Malaysia, 43400 UPM Serdang, Selangor (Malaysia); Khadum, A.A.H. [Institute of Fuel Cell, University Kebangsaan Malaysia, 43600 Bangi, Selangor (Malaysia)

    2011-04-15

    Cesium dihydrogen phosphate (CDP) nanoparticles were synthesized using the surfactants cetyltrimethyl ammonium bromide (CTAB), polyoxyethylene-polyoxypropylene (F-68) and (F-68:CTAB) with molar ratio 0.06. The samples conductivity such as CDP{sub CTAB}, CDP{sub F-68} and CDP{sub (F-68:CTAB)0.06} was studied by impedance spectroscopy in the frequency range 0.01 Hz to 1 MHz. The Nyquist plots were drawn at different temperatures of 210, 230 and 260 {sup o}C, which are defined below transition, phase transition and above transition, respectively. The measured conductivities obey the Arrhenius relation. The influence of surfactants on conductivity are more significant at higher temperature due to grain boundary. The conductivity of CDP{sub CTAB} increased slightly with increasing temperature to 260 {sup o}C, whereas the conductivity of other samples decreased with increasing temperature over 230 {sup o}C. The results indicated that the conductivities increase in the order of CDP{sub CTAB}>CDP{sub (F-68:CTAB)0.06}>CDP{sub F-68}. These are in accordance to the ion exchange capacities of the samples that the surfactant shows a direct influence on the samples proton mobility. It is found that the conductivity of CsH{sub 2}PO{sub 4} is influenced by surfactant type.

  6. Nafion as Cosurfactant: Solubilization of Nafion in Water in the Presence of Pluronics

    KAUST Repository

    Kelarakis, Antonios

    2011-01-18

    Incorporation of Nafion to aqueous solutions of Pluronics adversely impacts micellization due to extensive Nafion/copolymer interactions. Light scattering and zeta potential measurements provide evidence for the formation of sizable and stable Nafion/copolymer complexes, in expense of the neat copolymer micelles. At high copolymer concentrations, the overall interaction diagram of Nafion/copolymer reflects the competitive action of the release of packing constraints due to micellar destabilization induced by Nafion on one hand and the gelator nature of the Nafion on the other. Measurements using a quartz crystal microbalance (QCM-D) show that aqueous solutions of Pluronics (even at very low concentration) can dissolve the Nafion coating on the crystal resonator, while typical low molecular weight ionic surfactants fail to induce similar effects. These studies demonstrate that complexation with this class of copolymers is a facile route to impart dispersibility to Nafion in aqueous environments that otherwise can be achieved through tedious and harsh treatments. © 2010 American Chemical Society.

  7. Poly(lactide-co-glycolide)-laponite-F68 nanocomposite vesicles through a single-step double-emulsion method for the controlled release of doxorubicin.

    Science.gov (United States)

    Nair, Bindu P; Sharma, Chandra P

    2012-03-06

    Poly(lactide-co-glycolide) (PLGA)-laponite-F68 nanocomposite (PNC) vesicles were prepared through a technically facile, single-step water/oil/water double-emulsion method using ethyl acetate/water mixture. Vesicles of diameter 100 nm to 1.2 μm and average membrane thickness 30 nm were produced. Encapsulation with chemotherapeutic drug doxorubicin revealed unilamellar nature of the vesicle wall. PNC exhibited exfoliated morphology, enhanced thermal stability over neat PLGA, and a glass transition temperature of 54.29 °C. The zeta potential of -14.1 ± 0.231 for the vesicles revealed that the negatively charged PLGA surface is covered with neutral F68 in the vesicle wall. F68-Assisted formation of water/oil/water double emulsion of PNC in ethyl acetate/water mixture is proposed for the formation of the vesicles. Release characteristics of doxorubicin in phosphate-buffered saline (pH 7.4), cytotoxicity of bare and drug-loaded PNC vesicles with L929 cells, and uptake of doxorubicin with C6 fibroblast glioma cell line were also investigated.

  8. Effect of surfactants in synthesis of CsH2PO4 as protonic conductive membrane

    Indian Academy of Sciences (India)

    Soraya Hosseini; Wan Ramli Wan Daud; Marzieh Badiei; Abdul Amir Hassan Kadhum; Abu Bakar Mohammad

    2011-07-01

    Cesium dihydrogen phosphate (CDP) powders were synthesized by cetyltrimethylammoniumbromide (CTAB), polyoxyethylene-polyoxypropylene (F-68) and mixture of both surfactants F-68 : CTAB with two molar ratios 0.06 and 0.12 as surfactant solutions at room temperature. The synthesized CsH2PO4 is characterized by ICP, XRD, TEM, SEM, FT–IR, BET and IS techniques. Based on the width of the (011) XRD diffraction peak and BET measurement, the average size of nanoparticles was ∼ 10 nm in diameter, while the TEM images indicate smaller size than both techniques. The analysis reveals existence of P and Cs with mole ratio 1.02 ± 0.03 which is compatible to molar ratio CsH2PO4 formula. The experimental results show that the conductivities increase in the order of CDPCTAB > CDP(F-68 : CTAB)0.12 > CDP(F-68:CTAB)0.06 > CDPF-68. The sequence of increasing conductivity is in accordance with the ion exchange capacities of the samples that has direct proportional effect on the proton mobility of samples. Indeed CTAB as cationic surfactant shows the highest proton mobility in the as-obtained samples.

  9. Investigation of the imaging characteristics of the ALBIRA II small animal PET system for (18)F, (68)Ga and (64)Cu.

    Science.gov (United States)

    Attarwala, Ali Asgar; Karanja, Yvonne Wanjiku; Hardiansyah, Deni; Romanó, Chiara; Roscher, Mareike; Wängler, Björn; Glatting, Gerhard

    2017-06-01

    In this study the performance characteristics of the Albira II PET sub-system and the response of the system for the following radionuclides (18)F, (68)Ga and (64)Cu was analyzed. The Albira II tri-modal system (Bruker BioSpin MRI GmbH, Ettlingen, Germany) is a pre-clinical device for PET, SPECT and CT. The PET sub-system uses single continuous crystal detectors of lutetium yttrium orthosilicate (LYSO). The detector assembly consists of three rings of 8 detector modules. The transaxial field of view (FOV) has a diameter of 80mm and the axial FOV is 148mm. A NEMA NU-4 image quality phantom (Data Spectrum Corporation, Durham, USA) having five rods with diameters of 1, 2, 3, 4 and 5mm and a uniform central region was used. Measurements with (18)F, (68)Ga and (64)Cu were performed in list mode acquisition over 10h. Data were reconstructed using a maximum-likelihood expectation-maximization (MLEM) algorithm with iteration numbers between 5 and 50. System sensitivity, count rate linearity, convergence and recovery coefficients were analyzed. The sensitivities for the entire FOV (non-NEMA method) for (18)F, (68)Ga and (64)Cu were (3.78±0.05)%, (3.97±0.18)% and (3.79±0.37)%, respectively. The sensitivity based on the NEMA protocol using the (22)Na point source yielded (5.53±0.06)%. Dead-time corrected true counts were linear for activities ≤7MBq ((18)F and (68)Ga) and ≤17MBq ((64)Cu) in the phantom. The radial, tangential and axial full widths at half maximum (FWHMs) were 1.52, 1.47 and 1.48mm. Recovery coefficients for the uniform region with a total activity of 8MBq in the phantom were (0.97±0.05), (0.98±0.06), (0.98±0.06) for (18)F, (68)Ga and (64)Cu, respectively. The Albira II pre-clinical PET system has an adequate sensitivity range and the system linearity is suitable for the range of activities used for pre-clinical imaging. Overall, the system showed a favorable image quality for pre-clinical applications. Copyright © 2017. Published by Elsevier GmbH.

  10. Effect of Pluronic on Cellular Accumulation of Rhodamine 123, a P-gp Substrate in Caco-2 Cells%普流罗尼克对P-gp底物罗丹明123在Caco-2细胞蓄积的影响

    Institute of Scientific and Technical Information of China (English)

    关延彬; 左岚; 饶子超; 斯陆勤; 李高

    2011-01-01

    OBJECTIVE To determine whether Pluronic, P123, F127, P85, F68 and L61 possess ability to modulate P-glycoprotein(P-gp) mediated efflux of drugs. METHODS Caco-2 cell viability was measured using MTT assay in the presence of Pluronic at different concentrations. To evaluate the effects of Pluronic and verapamil( inhibitor of P-gp)on cellular drug accumulation in caco-2 cells, rhodamine 123(R-123), a P-gp substrate, was selected as fluorescent probe. A HPLC-fluorescence method was used to determined the concentration of R-123 in Caco-2 cells. Caco-2 cell membranes were exposed to various Pluronic solutions( P123 or F127),and then the ATPase activity of P-gp was assayed by determining liberated inorganic phosphate. RESULTS The viability of Pluronictreated cells was above 80% except L61, which suggested that Caco-2 cells could maintain their viability under the experiment conditions. In the presence of verapamil and Pluronic at concentrations ranging from 0.00 1 -50 mg · mL-1, R-123 accumulation were increased significantly to differernt extent. R-123 accumulation reached maximum levels when Pluronic concentrations were close to or above the CMC, Higher Pluronic concentrations resulted in a drop in accumulation compared to that of R-123 control. Furthermore,P123 and F127 treatments decreased P-gP ATPase activity in Caco-2 cell membranes expressing P-gp. CONCLUSION Pluronic (F68, F127, P123 and P85) can modulate drug effiux by inhibiting P-gp activity in Caco-2 cell membranes. It may be possible to improve the oral biuavailability of P-gp substrates by co-administration of Pluronic.%目的 研究普流罗尼克(Pluronic F127,F68,P85,P123)对小肠P-糖蛋白(P-gP)的调控作用.方法 采用MTT法检测不同质量浓度的Pluronic 时Caco-2细胞生长抑制作用;以P-gp底物罗丹明123(R-123)为荧光探针,评价各种Pluronic辅料和P-gp抑制剂维拉帕米对R-123细胞蓄积的影响,细胞内的R-123浓度采用高效液相-荧光检测.同时考察了Pluronic

  11. Formulation Optimization and Preliminary Evaluation of Pluronic Thermosensitive in situ Gel with a Suspending Agent of Xanthan Gum%以黄原胶为助悬剂的Pluronic温敏原位凝胶的处方筛选与初步评价

    Institute of Scientific and Technical Information of China (English)

    刘畅; 侯佳朋; 陆伟跃; 刘瑜

    2011-01-01

    To screen a combination of poloxamer and suspending agent with superior stability, good rheological property and suitable thermosensitivity, the influences of the amount of xanthan gum and poloxamers in the formulation of ornidazole in situ gel were investigated with sedimentation, redispersion and thermosensitivity as indexes. The optimum formulation was as follows: 0.1% xanthan gum, 16% Pluronic F127, 1% Pluronic F68, 10% ornidazole, 0.5% NaCl and 0.2% ethylparaben. The product with a gelation temperature of 35.9 ℃ had proper hardness, good redispersion and thermal stability.%以减少药物沉降、再分散性良好和不对原位凝胶温敏性产生不利影响为主要筛选指标,考察了难溶性药物奥硝唑的温敏原位凝胶中泊洛沙姆和助悬剂黄原胶用量等处方因素,筛选得到一种药物能稳定混悬、具有良好流变学性质和温敏性适宜的泊洛沙姆-助悬剂复配方案.所得最优处方为黄原胶0.1%,Pluronic F127 16%,Pluronic F68 1%,奥硝唑10%,氯化钠0.5%,尼泊金乙酯0.2%.制品凝胶化温度35.9℃,凝胶硬度适宜,药物沉降缓慢,再分散性和热稳定性良好.

  12. Preparation and in vitro evaluation of a pluronic lecithin organogel containing ricinoleic acid for transdermal delivery.

    Science.gov (United States)

    Boddu, Sai Hs; Bonam, Sindhu Prabha; Wei, Yangjie; Alexander, Kenneth

    2014-01-01

    The present study deals with the preparation and in vitro evaluation of a Pluronic lecithin organogel gel containing ricinoleic acid for transdermal delivery. Blank Pluronic lecithin organogel gels were prepared using ricinoleic acid as the oil phase and characterized for pH, viscosity, gelation temperature, and microscopic structure. The optimized Pluronic lecithin organogel gel formulation was further evaluated using ketoprofen (10%) and dexamethasone (0.5%) as model drugs. The stability and in vitro permeability of ketoprofen and dexamethasone was evaluated and compared with the corresponding control formulation (Pluronic lecithin organogel gel made with isopropyl palmitate as the oil phase). The pH and viscosity of blank Pluronic lecithin organogel gel prepared with ricinoleic acid was comparable with the isopropyl palmitate Pluronic lecithin organogel gel. The thixotropic property of ricinoleic acid Pluronic lecithin organogel gel was found to be better than the control. Drug-loaded Pluronic lecithin organogel gels behaved in a similar manner and all formulations were found to be stable at 25 degrees C, 35 degrees C, and 40 degrees C for up to 35 days. The penetration profile of dexamethasone was similar from both the Pluronic lecithin organogel gels, while the permeability for ketoprofen from Pluronic lecithin organogel gel containing ricinoleic acid was found to be three times higher as compared to the control formulation.

  13. Switchable Surfactants

    National Research Council Canada - National Science Library

    Yingxin Liu; Philip G. Jessop; Michael Cunningham; Charles A. Eckert; Charles L. Liotta

    2006-01-01

    .... We report that long-chain alkyl amidine compounds can be reversibly transformed into charged surfactants by exposure to an atmosphere of carbon dioxide, thereby stabilizing water/alkane emulsions...

  14. Degradable gene delivery systems based on Pluronics-modified low-molecular-weight polyethylenimine: preparation, characterization, intracellular trafficking, and cellular distribution

    Directory of Open Access Journals (Sweden)

    Ding X

    2012-02-01

    Full Text Available Wei Fan1,2,*, Xin Wu1,*, Baoyue Ding3,*, Jing Gao4, Zhen Cai1, Wei Zhang1, Dongfeng Yin1, Xiang Wang1, Quangang Zhu1, Jiyong Liu1, Xueying Ding4, Shen Gao1 1Department of Pharmaceutics, Changhai Hospital, Second Military Medical University, Shanghai, 2Department of Pharmaceutics, The 425th Hospital of PLA, Sanya, 3Department of Pharmaceutics, Medical College of Jiaxing University, Jiaxing, 4Department of Pharmaceutics, School of Pharmacy, Second Military Medical University, Shanghai, People's Republic of China*These authors contributed equally to this workBackground: Cationic copolymers consisting of polycations linked to nonionic amphiphilic block polymers have been evaluated as nonviral gene delivery systems, and a large number of different polymers and copolymers of linear, branched, and dendrimeric architectures have been tested in terms of their suitability and efficacy for in vitro and in vivo transfection. However, the discovery of new potent materials still largely relies on empiric approaches rather than a rational design. The authors investigated the relationship between the polymers' structures and their biological performance, including DNA compaction, toxicity, transfection efficiency, and the effect of cellular uptake.Methods: This article reports the synthesis and characterization of a series of cationic copolymers obtained by grafting polyethyleneimine with nonionic amphiphilic surfactant polyether-Pluronic® consisting of hydrophilic ethylene oxide and hydrophobic propylene oxide blocks. Transgene expression, cytotoxicity, localization of plasmids, and cellular uptake of these copolymers were evaluated following in vitro transfection of HeLa cell lines with various individual components of the copolymers.Results: Pluronics can exhibit biological activity including effects on enhancing DNA cellular uptake, nuclear translocation, and gene expression. The Pluronics with a higher hydrophilic-lipophilic balance value lead to

  15. Rheological properties of aqueous Pluronic-alginate systems containing liposomes.

    Science.gov (United States)

    Grassi, G; Crevatin, A; Farra, R; Guarnieri, G; Pascotto, A; Rehimers, B; Lapasin, R; Grassi, M

    2006-09-01

    Rheological and erosion studies regarding a liposome-containing polymeric blend that is propaedeutic to its use in paving techniques in tubular organs, such as blood vessels, are reported. Attention is focused on an aqueous polymeric blend composed of Pluronic (PF127) and alginate (Protanal LF 10/60) because both polymers, when dissolved in water at a sufficiently high concentration, are subjected to different structural mechanisms, which are driven by temperature increase and addition of bivalent cations, respectively, and both result in marked viscoelastic and plastic properties. After proving the compatibility between PF127 and alginate, we show that the structural transition temperature of the blend, T(ST), can be properly modulated. In particular, we found that T(ST) for an aqueous solution of pure Pluronic 20% w/w is about 21 degrees C and that even slight reductions in polymer concentration result in considerable T(ST) decrease. The addition of salts or alginate (provided as Na-alginate) provokes a substantial decrease of T(ST) and thus the alginate concentration in the blend should not exceed 1% w/w. In addition, liposomes slow down the structural transition but do not substantially affect the rheological properties of the system in the final state at higher temperatures, thus showing that they can be added to the polymeric blend without significant effects. Finally, erosion tests show that after contact with a source of bivalent cations, the polymeric blend containing PF127 and alginate shows an erosion resistance neatly improved with respect to the simple structured Pluronic system having the same polymer concentration. As a whole, all these results constitute the basis for future potential applications of the considered polymeric blend in tubular organs such as blood vessels.

  16. Therapeutic surfactant-stripped frozen micelles

    Science.gov (United States)

    Zhang, Yumiao; Song, Wentao; Geng, Jumin; Chitgupi, Upendra; Unsal, Hande; Federizon, Jasmin; Rzayev, Javid; Sukumaran, Dinesh K.; Alexandridis, Paschalis; Lovell, Jonathan F.

    2016-05-01

    Injectable hydrophobic drugs are typically dissolved in surfactants and non-aqueous solvents which can induce negative side-effects. Alternatives like `top-down' fine milling of excipient-free injectable drug suspensions are not yet clinically viable and `bottom-up' self-assembled delivery systems usually substitute one solubilizing excipient for another, bringing new issues to consider. Here, we show that Pluronic (Poloxamer) block copolymers are amenable to low-temperature processing to strip away all free and loosely bound surfactant, leaving behind concentrated, kinetically frozen drug micelles containing minimal solubilizing excipient. This approach was validated for phylloquinone, cyclosporine, testosterone undecanoate, cabazitaxel and seven other bioactive molecules, achieving sizes between 45 and 160 nm and drug to solubilizer molar ratios 2-3 orders of magnitude higher than current formulations. Hypertonic saline or co-loaded cargo was found to prevent aggregation in some cases. Use of surfactant-stripped micelles avoided potential risks associated with other injectable formulations. Mechanistic insights are elucidated and therapeutic dose responses are demonstrated.

  17. Small angle neutron scattering study of doxorubicin–surfactant complexes encapsulated in block copolymer micelles

    Indian Academy of Sciences (India)

    Jayita Bhattacharjee; Gunjan Verma; V K Aswal; P A Hassan

    2008-11-01

    Self-assembling behaviour of block copolymers and their ability to evade the immune system through polyethylene oxide stealth makes it an attractive candidate for drug encapsulation. Micelles formed by polyethylene oxide–polypropylene oxide–polyethylene oxide triblock copolymers (PEO–PPO–PEO), pluronic P123, have been employed for encapsulating the anti-cancer drug doxorubicin hydrochloride. The binding affinity of doxorubicin within the micelle carrier is enhanced through complex formation of drug and anionic surfactant, aerosol OT (AOT). Electrostatic binding of doxorubicin with negatively charged surfactants leads to the formation of hydrophobic drug–surfactant complexes. Surfactant-induced partitioning of the anti-cancer drug into nonpolar solvents such as chloroform is investigated. SANS measurements were performed on pluronic P123 mi-celles in the presence of drug–surfactant complex. No significant changes in the structure of the micelles are observed upon drug encapsulation. This demonstrates that surfactant–drug complexes can be encapsulated in block copolymer micelles without disrupting the structure of aggregates.

  18. Solubility of block copolymer surfactants in compressed CO{sub 2} using a lattice fluid hydrogen-bonding model

    Energy Technology Data Exchange (ETDEWEB)

    Takishima, Shigeki; O`Neill, M.L.; Johnston, K.P. [Univ. of Texas, Austin, TX (United States). Dept. of Chemical Engineering

    1997-07-01

    Supercritical carbon dioxide (CO{sub 2}) is an environmentally benign alternative to organic solvents in chemical processing. The solubilities of the homopolymers poly(ethylene glycol), poly(ethylene glycol) dimethyl ether (PEGDME), and poly(propylene glycol) (PPG) in CO{sub 2} were correlated with a lattice fluid hydrogen-bonding (LFHB) model, which was then used to predict solubilities of Pluronic L (PEG-PPG-PEG) and Pluronic R (PPG-PEG-PPG) triblock copolymers. Simple averaging rules were developed to evaluate the physical properties of the copolymers without introducing any adjustable parameters. For a given average molecular weight, the predictions of the model were quite reasonable and in some cases perhaps more accurate than the data, due to the large polydispersity of the samples. The model predicts the effects of total molecular weight, PEG/PPG ratio, terminal functional groups, temperature, and density on solubility. The much higher solubility of PPG versus PEG is due primarily to steric hindrance from the methyl branch, which weakens segment-segment interactions, and to a lesser extent to the stronger hydrogen bond donor strength of a primary (in the case of PEG) versus a secondary (in the case of PPG) alcohol terminal group. Consequently, the predicted solubilities of Pluronic L surfactants, which have stronger hydrogen bond donors on the terminal groups, are not much smaller than those of Pluronic R surfactants for given molecular weights of the blocks.

  19. Acidic surfactant solutions for tributylphosphate removal in nuclear fuel reprocessing plants: A formulation study

    Energy Technology Data Exchange (ETDEWEB)

    Causse, J.; Faure, S. [CEA Marcoule, LPAD, SPDE, DEN, 30 (France)

    2009-04-15

    The removal of tributylphosphate (TBP), an organic solvent widely used as a complexing agent for uranium and plutonium in nuclear plants, was investigated to understand and adapt the mechanisms involved in TBP detachment and solubilization in acidic surfactant solutions. Two well-known degreasing mechanisms, roll-up and emulsification, should be combined for maximum effect. These mechanisms were characterized with a CCD camera to measure contact angles between a solid substrate and a liquid drop. We measured the contact angles of a TBP drop deposited on a stainless steel plate immersed in an acidic surfactant solution, and quantified the amount of TBP solubilized in the micelles by turbidity measurements. Preliminary results of micelle size characterization by dynamic light scattering are presented. We formulated new acidic surfactant solutions associating two industrial surfactants, Pluronic P123 and Rewopal X1207L, with improvement factors in various fields (total organic matter content, oil detachment and solubilization efficiency, emulsion stability, etc.). (authors)

  20. The interactions between humic acids and Pluronic F127 produce nanoparticles useful for pharmaceutical applications

    Science.gov (United States)

    de Melo, Bruna Alice Gomes; Motta, Fernanda Lopes; Santana, Maria Helena Andrade

    2015-10-01

    Humic acids (HAs) are macromolecules composed of a large variety of functional groups including phenols and carboxylic acids, which have anti-inflammatory and antioxidant properties. HAs are completely soluble in aqueous medium in alkaline conditions only. At neutral pH, the protonation of the OH/OOH groups causes the formation of micelle-like structures containing a hydrophobic core. Pluronic F127 (PF127) is a nonionic and non-toxic block copolymer with surfactant properties, which are able to interact with HAs through hydrophobic interactions. In this work, these interactions were studied to determine the potential of HA-PF127 structures for pharmaceutical applications. The HAs used was composed of phenol (15.92 %), carboxylic (13.70 %), and other aromatic groups as characterized by 13C NMR, GC-MS, and FTIR. Initially, the HA-PF127 interactions were identified by a fivefold decrease in the CMC of PF127. The effects of the HA:PF127 molar ratio were studied by adding naturally occurring HAs to PF127 dispersions under mechanical stirring. The highest ratios, 1:8 and 1:80, favored the formation of submicellar aggregates of approximately 100 nm and zeta potentials of -28.37 and -30.23 mV, respectively. HA-PF127 structures were spherical, with a polydispersity of approximately 0.43. These results show that the interactions between HAs and PF127 produce stable nanoparticles. These nanoparticles may be used as a carrier for hydrophobic bioactives and as an antioxidant or anti-inflammatory agent. To the best of our knowledge, this work is the first attempt to develop HA-PF127 nanoparticles.

  1. The interactions between humic acids and Pluronic F127 produce nanoparticles useful for pharmaceutical applications

    Energy Technology Data Exchange (ETDEWEB)

    Melo, Bruna Alice Gomes de; Motta, Fernanda Lopes; Santana, Maria Helena Andrade, E-mail: mariahelena.santana@gmail.com [University of Campinas, Development of Biotechnological Processes Laboratory, School of Chemical Engineering (Brazil)

    2015-10-15

    Humic acids (HAs) are macromolecules composed of a large variety of functional groups including phenols and carboxylic acids, which have anti-inflammatory and antioxidant properties. HAs are completely soluble in aqueous medium in alkaline conditions only. At neutral pH, the protonation of the OH/OOH groups causes the formation of micelle-like structures containing a hydrophobic core. Pluronic F127 (PF127) is a nonionic and non-toxic block copolymer with surfactant properties, which are able to interact with HAs through hydrophobic interactions. In this work, these interactions were studied to determine the potential of HA–PF127 structures for pharmaceutical applications. The HAs used was composed of phenol (15.92 %), carboxylic (13.70 %), and other aromatic groups as characterized by {sup 13}C NMR, GC–MS, and FTIR. Initially, the HA–PF127 interactions were identified by a fivefold decrease in the CMC of PF127. The effects of the HA:PF127 molar ratio were studied by adding naturally occurring HAs to PF127 dispersions under mechanical stirring. The highest ratios, 1:8 and 1:80, favored the formation of submicellar aggregates of approximately 100 nm and zeta potentials of −28.37 and −30.23 mV, respectively. HA–PF127 structures were spherical, with a polydispersity of approximately 0.43. These results show that the interactions between HAs and PF127 produce stable nanoparticles. These nanoparticles may be used as a carrier for hydrophobic bioactives and as an antioxidant or anti-inflammatory agent. To the best of our knowledge, this work is the first attempt to develop HA–PF127 nanoparticles.

  2. Brushite foams--the effect of Tween® 80 and Pluronic® F-127 on foam porosity and mechanical properties.

    Science.gov (United States)

    Unosson, Johanna; Montufar, Edgar B; Engqvist, Håkan; Ginebra, Maria-Pau; Persson, Cecilia

    2016-01-01

    Resorbable calcium phosphate based bone void fillers should work as temporary templates for new bone formation. The incorporation of macropores with sizes of 100 -300 µm has been shown to increase the resorption rate of the implant and speed up bone ingrowth. In this work, macroporous brushite cements were fabricated through foaming of the cement paste, using two different synthetic surfactants, Tween® 80 and Pluronic® F-127. The macropores formed in the Pluronic samples were both smaller and less homogeneously distributed compared with the pores formed in the Tween samples. The porosity and compressive strength (CS) were comparable to previously developed hydroxyapatite foams. The cement foam containing Tween, 0.5M citric acid in the liquid, 1 mass% of disodium dihydrogen pyrophosphate mixed in the powder and a liquid to powder ratio of 0.43 mL/g, showed the highest porosity values (76% total and 56% macroporosity), while the CS was >1 MPa, that is, the hardened cement could be handled without rupture of the foamed structure. The investigated brushite foams show potential for future clinical use, both as bone void fillers and as scaffolds for in vitro bone regeneration.

  3. Pluronic F127/chitosan blend microspheres for mucoadhesive drug delivery

    Science.gov (United States)

    Gu, W. Z.; Hu, X. F.

    2017-01-01

    Pluronic F127/chitosan blend microspheres were prepared via emulsification and cross-linking process using glutaraldehyde as a cross-linker. Compared with chitosan microspheres fabricated under the same experimental conditions, blend microspheres exhibited better physical stability and higher swelling capacity. Puerarin, a traditional Chinese medicine, was incorporated into microparticlesas the model drug. The in vitro release of puerarin from blend microspheres was reduced because of the improved compatibility of the drug with the matrices. According to the results from in vitro adhesion experiments, mucoadhesive behavior of blend microspheres on a mucosa-like surface was similar to that of chitosan microspheres, despite their good ability of anti-protein absorption in solution.

  4. Gold-Pluronic core-shell nanoparticles: synthesis, characterization and biological evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Simon, Timea; Boca, Sanda [Babes-Bolyai University, Nanobiophotonics and Laser Microspectroscopy Center, Interdisciplinary Research Institute on Bio-Nano-Sciences and Faculty of Physics (Romania); Biro, Dominic [Sapientia University, Department of Mechanical Engineering, Faculty of Technical and Human Sciences (Romania); Baldeck, Patrice [Universite Joseph Fourier and CNRS, Laboratoire Interdisciplinaire de Physique, UMR 5588, CNRS (France); Astilean, Simion, E-mail: simion.astilean@phys.ubbcluj.ro [Babes-Bolyai University, Nanobiophotonics and Laser Microspectroscopy Center, Interdisciplinary Research Institute on Bio-Nano-Sciences and Faculty of Physics (Romania)

    2013-04-15

    This study presents the synthesis of gold-Pluronic core-shell nanoparticles by a two-step method and investigates their biological impact on cancer cells, specifically nanoparticle internalization and cytotoxicity. Uniform, 9-10-nm-sized, hydrophobic gold nanoparticles were synthesized in organic phase by reducing gold salt with oleylamine, after which oleylamine-protected gold nanoparticles were phase-transferred into aqueous medium using Pluronic F127 block copolymer, resulting in gold-Pluronic core-shell nanoparticles with a mean hydrodynamic diameter of {approx}35 nm. The formation and phase-transfer of gold nanoparticles were analyzed by UV-Vis absorption spectroscopy, transmission electron microscopy, and dynamic light scattering. The obtained gold-Pluronic core-shell nanoparticles proved to be highly stable in salted solution. Cytotoxicity tests showed no modification of cellular viability in the presence of properly purified particles. Furthermore, dark-field cellular imaging demonstrated that gold-Pluronic nanoparticles were able to be efficiently uptaken by cells, being internalized through nonspecific endocytosis. The high stability, proven biocompatibility, and imaging properties of gold-Pluronic core-shell nanoparticles hold promise for relevant intracellular applications, with such a design providing the feasibility to combine all multiple functionalities in one nanoparticle for simultaneous detection and imaging.

  5. TTC-Pluronic 3D radiochromic gel dosimetry of ionizing radiation

    Science.gov (United States)

    Kozicki, Marek; Kwiatos, Klaudia; Kadlubowski, Slawomir; Dudek, Mariusz

    2017-07-01

    This work reports the first results obtained using a new 3D radiochromic gel dosimeter. The dosimeter is an aqueous physical gel matrix made of poly(ethylene oxide)-block-poly(propylene oxide)-block-poly(ethylene oxide) (Pluronic F-127, PEO-PPO-PEO) doped with a representative of tetrazolium salts, 2, 3, 5-triphenyltetrazolium chloride (TTC). There were several reasons for the choice of Pluronic as a gel forming substrate: (i) the high degree of transparency and colourlessness; (ii) the possibility of gel dosimeter preparation at both high and low temperatures due to the phase behaviour of Pluronic; (iii) the broad temperature range over which the TTC-Pluronic dosimeter is stable; and (iv) the non-toxicity of Pluronic. A reason for the choice of TTC was its ionising radiation-induced transformation to water-insoluble formazan, which was assumed to impact beneficially on the spatial stability of the dose distribution. If irradiated, the TTC-Pluronic gels become red but transparent in the irradiated part, while the non-irradiated part remains crystal clear. The best obtained composition is characterised by  dose threshold, a dose sensitivity of 0.002 31 (Gy  ×  cm)-1, a large linear dose range of  >500 Gy and a dynamic dose response much greater than 500 Gy (7.5% TTC, 25% Pluronic F-127, 50 mmol dm-3 tetrakis). Temporal and spatial stability studies revealed that the TTC-Pluronic gels (7.5% TTC, 25% Pluronic F-127) were stable for more than one week. The addition of compounds boosting the gels’ dose performance caused deterioration of the gels’ temporal stability but did not impact the stability of the 3D dose distribution. The proposed method of preparation allows for the repeatable manufacture of the gels. There were no differences observed between gels irradiated fractionally and non-fractionally. The TTC-Pluronic dose response might be affected by the radiation source dose rate—this, however, requires further examination.

  6. The influence of Pluronics® on dark cytotoxicity, photocytotoxicity, localization and uptake of curcumin in cancer cells

    DEFF Research Database (Denmark)

    Singh, Ravinder; Tønnesen, Hanne Hjorth; Kristensen, Solveig

    2013-01-01

    In order to apply curcumin as a photosensitizer in photodynamic therapy (PDT) one needs a formulation that can solubilize and stabilize the compound. Pluronics® (Pluronic) are reported to both solubilize and stabilize curcumin against hydrolytic degradation. The aim of the present work was theref......In order to apply curcumin as a photosensitizer in photodynamic therapy (PDT) one needs a formulation that can solubilize and stabilize the compound. Pluronics® (Pluronic) are reported to both solubilize and stabilize curcumin against hydrolytic degradation. The aim of the present work...... was therefore to investigate the influence of Pluronic formulation on the photocytotoxicity of curcumin. Interactions between curcumin and Pluronics were investigated by fluorescence emission and absorption spectroscopy. Cell survival was measured with the MTT assay. The location of curcumin in the cells......-bound curcumin after 1 hour of incubation was independent of the presence of Pluronics. Curcumin was bound more strongly to cells when incubated with formulations without Pluronics compared to cells incubated with curcumin formulations with Pluronics. Incubation of WiDr cells with curcumin for 6 hours resulted...

  7. Pluronic嵌段共聚物F127胶团对布洛芬的增溶%Solubilization of Ibuprofen in Pluronic Block Copolymer F127 Micelles

    Institute of Scientific and Technical Information of China (English)

    万东华; 郑欧; 周燕; 吴莉瑜

    2010-01-01

    研究了Pluronic F127胶团溶液对药物布洛芬(IBU)的增溶作用.通过芘探针荧光法测定了不同温度下F127在水溶液和0.01 mol·L-1 pH 7.4磷酸盐缓冲生理(PBS)溶液中的临界胶束浓度(cmc),采用高效液相色谱(HPLC)测定了F127溶液中布洛芬的溶解度,并依据公式计算了增溶参数(摩尔增溶量X和胶团-水分配系数K),考察了温度、溶剂和F68的加入对F127胶团化行为及其对布洛芬增溶作用的影响.结果表明:布洛芬的溶解度随F127质量分数的提高线性增加:随着温度升高,cmc急剧下降,胶团内核的疏水性增强,X和K稍有增大;与水溶液相比,在PBS溶液中cmc减小,X乎不变,K显著降低;F68的加入对F127胶团的性质几乎无影响,对增溶的影响也不明显.对增溶参数的分析表明,K反映的是药物布洛芬的性质,X则可反映嵌段共聚物F127的溶解效能,并证实了布洛芬是通过F127胶团的内核和栅栏层而实现增溶的.

  8. Surfactant effect on the upconversion emission and decay time of ZrO{sub 2}:Yb-Er nanocrystals

    Energy Technology Data Exchange (ETDEWEB)

    Solis, D. [Centro de Investigaciones en Optica, A.P. 1-948, Leon, Gto. 37160 (Mexico); Lopez-Luke, T. [Centro de Investigaciones en Optica, A.P. 1-948, Leon, Gto. 37160 (Mexico); IIM, UMSNH, C.U., Morelia, Mich. 58060 (Mexico); De la Rosa, E. [Centro de Investigaciones en Optica, A.P. 1-948, Leon, Gto. 37160 (Mexico)], E-mail: elder@cio.mx; Salas, P. [Centro de Fisica Aplicada y Tecnologia Avanzada, Universidad Nacional Autonoma de Mexico, A.P. 1-1010, Queretaro, Qro. 76000 (Mexico); Angeles-Chavez, C. [Instituto Mexicano del Petroleo, Cd. Mexico, D.F. 07730 (Mexico)

    2009-05-15

    Luminescent properties of doped ZrO{sub 2}:Er{sup 3+} and codoped ZrO{sub 2}:Yb{sup 3+}-Er{sup 3+} nanocrystals with average size {approx}54 nm were analyzed as a function of non-ionic surfactant (Pluronic F-127) concentration. Surfactant and non-surfactant samples were prepared by the sol-gel micelle process with hydrothermal aging and annealed at 1000 deg. C for 5 h. The introduction of the surfactant reduces the presence of impurities such as OH and CO{sub 2} on both samples, and increments the tetragonal phase for codoped nanocrystals. It induces an increment larger than 90% and 70% for doped and codoped, respectively, for an optimum molar ratio of 0.0082. The observed enlargement of fluorescence decay time is partly the result of the nanosize effect but is dominated by the reduction of impurities attached on the nanocrystalline surface.

  9. Thermally cleavable surfactants

    Science.gov (United States)

    McElhanon, James R.; Simmons, Blake A.; Zifer, Thomas; Jamison, Gregory M.; Loy, Douglas A.; Rahimian, Kamyar; Long, Timothy M.; Wheeler, David R.; Staiger, Chad L.

    2006-04-04

    Two new surfactant molecules are reported which contain thermally labile Diels-Alder adducts connecting the polar and non-polar sections of each molecule. The two surfactants possess identical non-polar dodecyl tail segments but exhibit different polar headgroups. The surfactants become soluble in water when anionic salts are formed through the deprotonation of the surfactant headgroups by the addition of potassium hydroxide. When either surfactant is exposed to temperature above about 60.degree. C., the retro Diels-Alder reaction occurs, yielding hydrophilic and hydrophobic fragments and the aqueous solutions of the surfactants subsequently exhibit loss of all surface-active behavior.

  10. Thermally cleavable surfactants

    Energy Technology Data Exchange (ETDEWEB)

    McElhanon, James R. (Manteca, CA); Simmons, Blake A. (San Francisco, CA); Zifer, Thomas (Manteca, CA); Jamison, Gregory M. (Albuquerque, NM); Loy, Douglas A. (Albuquerque, NM); Rahimian, Kamyar (Albuquerque, NM); Long, Timothy M. (Urbana, IL); Wheeler, David R. (Albuquerque, NM); Staiger, Chad L. (Albuquerque, NM)

    2009-09-29

    Two new surfactant molecules are reported which contain thermally labile Diels-Alder adducts connecting the polar and non-polar sections of each molecule. The two surfactants possess identical non-polar dodecyl tail segments but exhibit different polar headgroups. The surfactants become soluble in water when anionic salts are formed through the deprotonation of the surfactant headgroups by the addition of potassium hydroxide. When either surfactant is exposed to temperature above about 60.degree. C., the retro Diels-Alder reaction occurs, yielding hydrophilic and hydrophobic fragments or the aqueous solutions of the surfactants subsequently exhibit loss of all surface-active behavior.

  11. Thermally cleavable surfactants

    Energy Technology Data Exchange (ETDEWEB)

    McElhanon, James R. (Manteca, CA); Simmons, Blake A. (San Francisco, CA); Zifer, Thomas (Manteca, CA); Jamison, Gregory M. (Albuquerque, NM); Loy, Douglas A. (Albuquerque, NM); Rahimian, Kamyar (Albuquerque, NM); Long, Timothy M. (Urbana, IL); Wheeler, David R. (Albuquerque, NM); Staiger, Chad L. (Albuquerque, NM)

    2009-11-24

    Two new surfactant molecules are reported which contain thermally labile Diels-Alder adducts connecting the polar and non-polar sections of each molecule. The two surfactants possess identical non-polar dodecyl tail segments but exhibit different polar headgroups. The surfactants become soluble in water when anionic salts are formed through the deprotonation of the surfactant headgroups by the addition of potassium hydroxide. When either surfactant is exposed to temperature above about 60.degree. C., the retro Diels-Alder reaction occurs, yielding hydrophilic and hydrophobic fragments or the aqueous solutions of the surfactants subsequently exhibit loss of all surface-active behavior.

  12. Preparation and characterization of cationic Pluronic for surface modification and functionalization of polymeric drug delivery nanoparticles

    Directory of Open Access Journals (Sweden)

    G. Gyulai

    2016-03-01

    Full Text Available Biodegradable poly(lactic-co-glycolic acid copolymer, PLGA nanoparticles (NPs with a surface layer of poly (ethylene oxide-poly(propylene oxide-poly(ethylene oxide triblock copolymers, Pluronics, are promising drug carrier systems. With the aim to increase the potential of targeted drug delivery the end group derivative of Pluronics was synthesized in a straightforward way to obtain Pluronic-amines. The formation of functional amine groups was confirmed by fluorescamine method and NMR analysis of their N-(tert-Butoxycarbonyl-L-phenylalanine (Boc-Phe-OH and N-(9-Fluorenylmethoxycarbonyl-L-phenylalanine (Fmoc-Phe-OH conjugates. Pluronic and Pluronic-amine stabilized PLGA NPs prepared by nanoprecipitation were characterized by dynamic light scattering and zeta potential measurements. All of the systems showed high colloidal stability checked by electrolyte induced aggregation, although the presence of Pluronicamine on the surface decreased the zeta potential in some extent. The introduction of reactive primary amine groups into the surface layer of PLGA NPs while preserving the aggregation stability, provides a possibility for coupling of various ligands allowing targeted delivery and also contributes to the improved membrane affinity of NPs.

  13. Phase Behavior and Micellar Packing of Impurity-Free Pluronic Block Copolymers in Water

    Science.gov (United States)

    Ryu, Chang Yeol; Park, Hanjin

    We have investigated the impacts of the non-micellizable polymeric impurities on the micellar packing and solution phase behavior of Pluronic block copolymers in water. In particular, small angle x-ray scattering, rheology and dynamic light scattering techniques have been employed to elucidate how the low MW impurities affect the micellar packing and solution phase diagram in water, when ordered cubic structures of spherical micelles are formed. A silica slurry method has been developed using the competitive adsorption of the PEO-PPO-PEO triblock copolymers over the low MW polymeric impurities for a large scale purification of Pluronics and it purity of Pluronics has been assessed by interaction chromatography. Based on the comparative studies on micellar packing between As-Received (AR) and Purified (Pure) Pluronic F108 solutions, we found experimental evidence to support the hypothesis that the inter-micellar distance of Pluronic cubic structures in aqueous solution is governed by the effective polymer concentration in terms of PEO-PPO-PEO triblock copolymers. Removal of the impurities in AR F108 offers an important clue on window into the onset of BCC ordering via hydrodynamic contact between micelles in solution. NSF DMR Polymers.

  14. Surfactant-Assisted Sol-Gel Synthesis of TiO2 with Uniform Particle Size Distribution

    Directory of Open Access Journals (Sweden)

    O. L. Galkina

    2011-01-01

    Full Text Available TiO2 materials were prepared from a titanium isopropoxide precursor by sol-gel processing in water media with or without various templates (polyethylenimine or Pluronic P-123. The photocatalytic efficiency of the samples was found to depend strongly on the use of and type of template added. Titania/Pluronic sols resulted in homogeneous anatase TiO2—rutile with uniform particle size distribution after calcination (400°C. Optical properties of the samples were characterized by UV-Vis spectroscopy and crystalline structures by X-ray diffraction. A surfactant-assisted sol-gel process retarded crystallization of the anatase and rutile titania, which resulted in smaller grain sizes and presumably a larger active surface area. The morphology of the surfaces was obtained by AFM techniques. The highest photobleaching rate was found for samples deposited from the sol with the addition of the Pluronic P-123 surfactant, and it was almost twice as high as that for films deposited from sols with polyethylenimine.

  15. Formulation and clinical evaluation of silymarin pluronic-lecithin organogels for treatment of atopic dermatitis

    Science.gov (United States)

    Mady, Fatma M; Essa, Hanaa; El-Ammawi, Tarek; Abdelkader, Hamdy; Hussein, Amal K

    2016-01-01

    Silymarin is a naturally occurring flavonoid drug; evidence from recent research has highlighted its use as a potential treatment for atopic dermatitis (AD). Both poor water solubility and drug permeability have hindered the percutaneous absorption of silymarin. Formulation of silymarin into pluronic-lecithin organogel (PLO) basis for topical skin delivery is the main aim of this work. Six different PLO formulations were prepared containing various pluronic to lecithin ratios using two cosolvent systems of ethyl alcohol and dimethyl sulfoxide. Formulation 2 (20% pluronic and 3% lecithin) was found to be the optimal base for topical delivery of silymarin as it showed optimum pH, viscosity, drug content, and satisfactory in vitro silymarin permeation. The silymarin PLO formulation significantly relieved inflammatory symptoms of AD such as redness, swelling, and inflammation. These findings warrant the ability for application of these novel silymarin PLO formulations as a novel treatment for AD. PMID:27022248

  16. Formulation and clinical evaluation of silymarin pluronic-lecithin organogels for treatment of atopic dermatitis.

    Science.gov (United States)

    Mady, Fatma M; Essa, Hanaa; El-Ammawi, Tarek; Abdelkader, Hamdy; Hussein, Amal K

    2016-01-01

    Silymarin is a naturally occurring flavonoid drug; evidence from recent research has highlighted its use as a potential treatment for atopic dermatitis (AD). Both poor water solubility and drug permeability have hindered the percutaneous absorption of silymarin. Formulation of silymarin into pluronic-lecithin organogel (PLO) basis for topical skin delivery is the main aim of this work. Six different PLO formulations were prepared containing various pluronic to lecithin ratios using two cosolvent systems of ethyl alcohol and dimethyl sulfoxide. Formulation 2 (20% pluronic and 3% lecithin) was found to be the optimal base for topical delivery of silymarin as it showed optimum pH, viscosity, drug content, and satisfactory in vitro silymarin permeation. The silymarin PLO formulation significantly relieved inflammatory symptoms of AD such as redness, swelling, and inflammation. These findings warrant the ability for application of these novel silymarin PLO formulations as a novel treatment for AD.

  17. Synthesis and Characterization of Nanoporous Carbon Materials; The Effect of Surfactant Concentrations and Salts

    Directory of Open Access Journals (Sweden)

    Shokoofeh Geranmayeh

    2011-01-01

    Full Text Available Nanoporous carbon framework was synthesized using phenol and formaldehyde as carbon precursors and triblock copolymer (pluronic F127 as soft template via evaporation induced self-assembly. Hexagonal mesoporous carbon with specific surface area of 350 m2/g through optimizing the situation was obtained. The effects of different surfactant/phenol molar ratio and presence of salts on specific surface area, pore size and pore volume for all the prepared samples were studied by means of the Brunauer-Emmett-Teller (BET formalism, powder X-ray diffraction technique and FT-IR spectroscopy.

  18. Emulsion electrospinning of polycaprolactone: influence of surfactant type towards the scaffold properties.

    Science.gov (United States)

    Hu, Jue; Prabhakaran, Molamma P; Ding, Xin; Ramakrishna, Seeram

    2015-01-01

    Producing uniform nanofibers in high quality by electrospinning remains a huge challenge, especially using low concentrated polymer solutions. However, emulsion electrospinning assists to produce nanofibers from less concentrated polymer solutions compared to the traditional electrospinning process. The influence of individual surfactants towards the morphology of the emulsion electrospun poly (ɛ-caprolactone)/bovine serum albumin (PCL/BSA) nanofibers were investigated by using (i) non-ionic surfactant sorbitane monooleate (Span80); (ii) anionic sodium dodecyl sulfate (SDS); and (iii) cationic benzyltriethylammonium chloride, and poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) triblock copolymer Pluronic F108 of different concentrations. The morphology, along with the chemical and mechanical properties of the fibers, was evaluated by field emission scanning electron microscopy, attenuated total reflectance Fourier transform infrared spectroscopy, differential scanning calorimetry, water contact angle, and tensile tester. With the addition of surfactants, the electrospinnability of dilute PCL solution was enhanced, with either branched or uniform fibers were obtained. Electrospinning of an emulsion containing 0.4% (w/v) SDS produced the smallest and the most uniform nanofibers (167 ± 39 nm), which was attributed to the high conductivity of the solution. Analysis revealed that the emulsion electrospun nanofibers containing different surfactants and surfactant concentrations differ in fiber morphology and mechanical properties. Results suggest that surfactants have the ability to modulate the fiber morphology via electrostatic and hydrogen bonding, depending on their chemical structure.

  19. In vitro percutaneous absorption of ketoprofen and testosterone: comparison of pluronic lecithin organogel vs. pentravan cream.

    Science.gov (United States)

    Lehman, Paul A; Raney, Sam G

    2012-01-01

    An in vitro human percutaneous absorption study was conducted to assess the delivery of ketoprofen and testosterone from two base formulations, a Pluronic lecithin organogel and Pentravan Cream. Each formulation was applied to ex vivo human trunk skin (from three skin donors) on triplicate sections mounted onto Franz Diffusion Cells. Following a 5-mcL/cm2 applied dose, serial dermal receptor solutions were collected over 48 hours. For both compounds, a greater rate and extent of absorption was found from the Pentravan formulation than from the Pluronic lecithin organogel formulation: 3.8-fold greater for ketoprofen, 1.7-fold greater for testosterone, for amount absorbed.

  20. New Biopolymer Nanoparticles Improve the Solubility of Lipophilic Megestrol Acetate

    Directory of Open Access Journals (Sweden)

    Malwina Lachowicz

    2016-02-01

    Full Text Available As many substances are poorly soluble in water and thus possess decreased bioavailability, creating orally administered forms of these substances is a challenge. The objective of this study was to determine whether the solubility of megestrol acetate, a Biopharmaceutical Classification System (BCS class II drug, can be improved by using a newly-synthesized surfactant (Rofam 70: a rapeseed methyl ester ethoxylate and compare it with two references surfactants (Tween 80, Pluronic F68 at three different pH values. Spectrophotometry was used to compare the solubility profiles in the presence of three tested surfactants at pH 5.0, 7.4 and 9.0. Rapeseed methyl ester ethoxylate was found to improve the solubility of the BCS Class II drug and increase its bioavailability; It increased drug solubility more effectively than Pluronic F68. Its cytotoxicity results indicate its possible value as a surfactant in Medicine and Pharmacy.

  1. Pluronic-lysozyme conjugates as anti-adhesive and antibacterial bifunctional polymers for surface coating

    NARCIS (Netherlands)

    Muszanska, A.K.; Busscher, H.J.; Herrmann, A.; Mei, van der H.C.; Norde, W.

    2011-01-01

    This paper describes the preparation and characterization of polymer protein conjugates composed of a synthetic triblock copolymer with a central polypropylene oxide (PPO) block and two terminal polyethylene oxide (PEO) segments, Pluronic F-127, and the antibacterial enzyme lysozyme attached to the

  2. Pluronic-lysozyme conjugates as anti-adhesive and antibacterial bifunctional polymers for surface coating

    NARCIS (Netherlands)

    Muszanska, Agnieszka K.; Busscher, Henk J.; Herrmann, Andreas; van der Mei, Henny C.; Norde, Willem

    This paper describes the preparation and characterization of polymer protein conjugates composed of a synthetic triblock copolymer with a central polypropylene oxide (PPO) block and two terminal polyethylene oxide (PEO) segments, Pluronic F-127, and the antibacterial enzyme lysozyme attached to the

  3. Pharmacokinetics and biodistribution of polymeric micelles of paclitaxel with Pluronic P123

    Institute of Scientific and Technical Information of China (English)

    Li-mei HAN; Lie GUO; Li-jun ZHANG; Qing-song WANG; Xiao-ling FANG

    2006-01-01

    Aim: To investigate the preparation, in vitro release, in vivo pharmacokinetics and tissue distribution of a novel polymeric micellar formulation of paclitaxel (PTX) with Pluronic P123. Methods: The polymeric micelles of paclitaxel with Pluronic PI23 were prepared by a solid dispersion method. The characteristics of micelles including particle size distribution, morphology and in vitro release of PTX from micelles were carried out. PTX-loaded micellar solutions were administered through the tail vein to healthy Sprague-Dawley rats and Kunming strain mice to assess the pharmacokinetics and tissue distribution of PTX, respectively. Taxol, the commercially available intravenous formulation of PTX, was also administered as control. Results: By using a dynamic light scattering sizer and a transmission electron microscopy, it was shown that the PTX-loaded micelles had a mean size of approximately 25 nm with narrow size distribution and a spherical shape. PTX was continuously released from Pluronic PI23 micelles in release medium containing 1 mol/L sodium salicylate for 24 h at 37℃. In the pharmacokinetic assessment, t1/2β and AUC of micelle formulation were 2.3 and 2.9-fold higher than that of Taxol injection. And the PTX-loaded micelles increased the uptake of PTX in the plasma, ovary and uterus, lung, and kidney, but decreased uptake in the liver and brain in the biodistribution study. Conclusion: Polymeric micelles using Pluronic P123 can effectively solubilize PTX, prolong blood circulation time and modify the biodistribution of PTX.

  4. Pluronic-lysozyme conjugates as anti-adhesive and antibacterial bifunctional polymers for surface coating

    NARCIS (Netherlands)

    Muszanska, A.K.; Busscher, H.J.; Herrmann, A.; Mei, van der H.C.; Norde, W.

    2011-01-01

    This paper describes the preparation and characterization of polymer protein conjugates composed of a synthetic triblock copolymer with a central polypropylene oxide (PPO) block and two terminal polyethylene oxide (PEO) segments, Pluronic F-127, and the antibacterial enzyme lysozyme attached to the

  5. Formulation and clinical evaluation of silymarin pluronic-lecithin organogels for treatment of atopic dermatitis

    Directory of Open Access Journals (Sweden)

    Mady FM

    2016-03-01

    Full Text Available Fatma M Mady,1,2 Hanaa Essa,2 Tarek El-Ammawi,3 Hamdy Abdelkader,2 Amal K Hussein2 1Department of Pharmaceutics and Pharmaceutical Technology, Faculty of Pharmacy, Taibah University, Medina, Saudi Arabia; 2Department of Pharmaceutics, Faculty of Pharmacy, Minia University, Minia, Egypt; 3Department of Dermatology, STDs, and Andrology, Minia University Hospital, Minia, Egypt Abstract: Silymarin is a naturally occurring flavonoid drug; evidence from recent research has highlighted its use as a potential treatment for atopic dermatitis (AD. Both poor water solubility and drug permeability have hindered the percutaneous absorption of silymarin. Formulation of silymarin into pluronic-lecithin organogel (PLO basis for topical skin delivery is the main aim of this work. Six different PLO formulations were prepared containing various pluronic to lecithin ratios using two cosolvent systems of ethyl alcohol and dimethyl sulfoxide. Formulation 2 (20% pluronic and 3% lecithin was found to be the optimal base for topical delivery of silymarin as it showed optimum pH, viscosity, drug content, and satisfactory in vitro silymarin permeation. The silymarin PLO formulation significantly relieved inflammatory symptoms of AD such as redness, swelling, and inflammation. These findings warrant the ability for application of these novel silymarin PLO formulations as a novel treatment for AD. Keywords: silymarin, pluronic lecithin organogel, atopic dermatitis, skin penetration 

  6. Peptide-Mediated Tumor Targeting by a Degradable Nano Gene Delivery Vector Based on Pluronic-Modified Polyethylenimine

    Science.gov (United States)

    Wu, Zhaoyong; Zhan, Shuyu; Fan, Wei; Ding, Xueying; Wu, Xin; Zhang, Wei; Fu, Yinghua; Huang, Yueyan; Huang, Xuan; Chen, Rubing; Li, Mingjuan; Xu, Ningyin; Zheng, Yongxia; Ding, Baoyue

    2016-03-01

    Polyethylenimine (PEI) is considered to be a promising non-viral gene delivery vector. To solve the toxicity versus efficacy and tumor-targeting challenges of PEI used as gene delivery vector, we constructed a novel non-viral vector DR5-TAT-modified Pluronic-PEI (Pluronic-PEI-DR5-TAT), which was based on the attachment of low-molecular-weight polyethylenimine (LMW-PEI) to the amphiphilic polymer Pluronic to prepare Pluronic-modified LMW-PEI (Pluronic-PEI). This was then conjugated to a multifunctional peptide containing a cell-penetrating peptide (TAT) and a synthetic peptide that would bind to DR5—a receptor that is overexpressed in cancer cells. The vector showed controlled degradation, favorable DNA condensation and protection performance. The Pluronic-PEI-DR5-TAT/DNA complexes at an N/P ratio of 15:1 were spherical nanoparticles of 122 ± 11.6 nm and a zeta potential of about 22 ± 2.8 mV. In vitro biological characterization results indicated that Pluronic-PEI-DR5-TAT/DNA complexes had a higher specificity for the DR5 receptor and were taken up more efficiently by tumor cells than normal cells, compared to complexes formed with PEI 25 kDa or Pluronic-PEI. Thus, the novel complexes showed much lower cytotoxicity to normal cells and higher gene transfection efficiency in tumor cells than that exhibited by PEI 25 kDa and Pluronic-PEI. In summary, our novel, degradable non-viral tumor-targeting vector is a promising candidate for use in gene therapy.

  7. Surfactants in tribology

    CERN Document Server

    Biresaw, Girma

    2014-01-01

    Surface science and tribology play very critical roles in many industries. Manufacture and use of almost all consumer and industrial products rely on the application of advanced surface and tribological knowledge. The fourth in a series, Surfactants in Tribology, Volume 4 provides an update on research and development activities connecting surfactants and tribological phenomena. Written by renowned subject matter experts, the book demonstrates how improved design of surfactants can be harnessed to control tribological phenomena. Profusely illustrated and copiously referenced, the chapters also

  8. Physical characterization of alginate-Pluronic F127 gel for endoluminal NABDs delivery.

    Science.gov (United States)

    Abrami, Michela; D'Agostino, Ilenia; Milcovich, Gesmi; Fiorentino, Simona; Farra, Rossella; Asaro, Fioretta; Lapasin, Romano; Grassi, Gabriele; Grassi, Mario

    2014-02-07

    Here we focus the attention on the physical characteristics of a highly biocompatible hydrogel made up of crosslinked alginate and Pluronic F127 (PF127). This is a composite polymeric blend we propose for artery endoluminal delivery of an emerging class of molecules named nucleic acid based drugs (NABDs). The physical characterization of our composite gel, i.e. mesh size distribution and PF127-alginate mutual organization after crosslinking, can significantly determine the NABDs release kinetics. Thus, to explore these aspects, different technical approaches, i.e. rheology, low/high field NMR and TEM, were used. While rheology provided information at the macroscopic and nano-level, the other three approaches gave details at the nano-level. We observe that Pluronic micelles, organizing in cubic ordered domains, generate, upon alginate crosslinking, the formation of meshes (≈ 150 nm) larger than those occurring in a Pluronic-free alginate network (≈ 25 nm). Nevertheless, smaller alginate meshes are still on and can just host un-structured Pluronic micelles and water. Accordingly, the gel structure is quite inhomogeneous, where big meshes (filled by crystalline Pluronic) co-exist with smaller meshes (hosting water and un-structured PF127 micelles). While big meshes offer a considerable hindering action on a diffusing solute, smaller ones represent a sort of free space where solute diffusion is faster. The presence of big and small meshes indicates that drug release may follow a double kinetics characterized by a fast and slow release. Notably, this behavior is considered appropriate for endoluminal drug release to the arterial wall.

  9. POLYMERIC SURFACTANT STRUCTURE

    Institute of Scientific and Technical Information of China (English)

    P.M. Saville; J.W. White

    2001-01-01

    Polymeric surfactants are amongst the most widespread of all polymers. In nature, proteins and polysaccharides cause self organization as a result of this surfactancy; in industry, polymeric surfactants play key roles in the food, explosives and surface coatings sectors. The generation of useful nano- and micro-structures in films and emulsions as a result of polymer amphiphilicity and the application of mechanical stress is discussed. The use of X-ray and neutron small angle scattering and reflectivity to measure these structures and their dynamic properties will be described. New results on linear and dendritic polymer surfactants are presented.

  10. Dendrimer-surfactant interactions.

    Science.gov (United States)

    Cheng, Yiyun; Zhao, Libo; Li, Tianfu

    2014-04-28

    In this article, we reviewed the interactions between dendrimers and surfactants with particular focus on the interaction mechanisms and physicochemical properties of the yielding dendrimer-surfactant aggregates. In order to provide insight into the behavior of dendrimers in biological systems, the interactions of dendrimers with bio-surfactants such as phospholipids in bulk solutions, in solid-supported bilayers and at the interface of phases or solid-states were discussed. Applications of the dendrimer-surfactant aggregates as templates to guide the synthesis of nanoparticles and in drug or gene delivery were also mentioned.

  11. Surfactant Sector Needs Urgent Readjustment

    Institute of Scientific and Technical Information of China (English)

    Huang Hongzhou

    2007-01-01

    @@ Surfactant industrial system has been basically established After 50 years' development, China has already established a surfactant industrial system with a relatively complete product portfolio and can produce 4714 varieties of surfactants in cationic,anionic, nonionic and amphoteric categories.

  12. SURFACTANTS IN LUBRICATION

    Science.gov (United States)

    Surfactants are one of the most widely applied materials by consumers and industry. The application areas for surfactants span from everyday mundane tasks such as cleaning, to highly complex processes involving the formulation of pharmaceuticals, foods, pesticides, lubricants, etc. Even though sur...

  13. Dynamic covalent surfactants

    NARCIS (Netherlands)

    Minkenberg, C.B.

    2012-01-01

    In this thesis the development of surfactant aggregates with fast exchange dynamics between the aggregated and non-aggregated state is described. Dynamic surfactant exchange plays an important role in natural systems, for instance in cell signaling, cell division, and uptake and release of cargo. Re

  14. Evaluation of the stability of fluoxetine in pluronic lecithin organogel and the determination of an appropriate beyond-use date.

    Science.gov (United States)

    Peacock, Gina F; Sauvageot, Jurgita

    2014-01-01

    Fluoxetine is a commonly prescribed psychotropic medication for a variety of behavioral diagnoses in veterinary practice, and fluoxetine in Pluronic lecithin organogel has been used successfully in treating inappropriate urine spraying in felines. Historically, pharmacists have assigned a variety of beyond-use dates to extemporaneously compound drugs in Pluronic lecithin organogel. The objective of this study was to evaluate the stability of fluoxetine in Pluronic lecithin organogel over a period of six months and to determine an appropriate beyond-use date. A stability-indicating high-performance liquid chromatography method for fluoxetine in Pluronic lecithin organogel was validated in our laboratory. Fluoxetine-Pluronic lecithin organogel 50 mg/mL was prepared by a local compounding pharmacy and analyzed by high-performance liquid chromatograph at 0, 7, 14, 21, 28, 45, 60, 90, and 180 days. Physical stability was also assessed by visual observation. At each time point percent of initial concentration was calculated. The beyond-use date was determined as the time period that the samples maintained at least 90 percent of the initial concentration. At 180 days, the mean percent of initial concentration was 99 +/- 1.5 and, visually, the fluoxetine-Pluronic lecithin organogel retained the original color and consistency, without detectable separation of the different phases of Pluronic lecithin organogel. Since fluoxetine was physically stable and retained greater than 90 percent of initial concentration in Pluronic lecithin organogel for 180 days when stored at room temperature and protected from light, a beyond-use date of 180 days is appropriate.

  15. Solubilization of parabens in aqueous Pluronic solutions: investigating the micellar growth and interaction as a function of paraben composition.

    Science.gov (United States)

    Khimani, M; Ganguly, R; Aswal, V K; Nath, S; Bahadur, P

    2012-12-27

    The influence of methyl paraben (MP) and butyl paraben (BP) on the aggregation characteristics of Pluronics in an aqueous medium has been investigated by DLS, SANS, viscometry, and fluorescence measurement techniques. Parabens are extensively used as preservatives in cosmetic, pharmaceutical, and food products. In this paper, we show that their influence on the restructuring and growth of Pluronics micelles vary quite significantly with their aqueous solubility and with the composition of Pluronics. In the case of P105 and P104, MP reduces the sphere-to-rod transition temperature down to room temperature, but BP with significantly less aqueous solubility than MP suppresses such micellar transition and leads to the formation of micellar clusters due to the onset of intermicellar attractive interaction. In the case of more hydrophobic Pluronic P103, on the other hand, both MP and BP are able to induce rapid room temperature sphere-to-rod micellar growth, which is not observed in the presence of water structure making salts like NaCl and Na(3)PO(4). These observations have been attributed to modulation of growth and restructuring processes of the Pluronic micelles arising due to different locations of parabens within the micellar corona as determined by their aqueous solubility and the hydrophobicity of the Pluronics.

  16. Surfactants in the environment.

    Science.gov (United States)

    Ivanković, Tomislav; Hrenović, Jasna

    2010-03-01

    Surfactants are a diverse group of chemicals that are best known for their wide use in detergents and other cleaning products. After use, residual surfactants are discharged into sewage systems or directly into surface waters, and most of them end up dispersed in different environmental compartments such as soil, water or sediment. The toxic effects of surfactants on various aquatic organisms are well known. In general, surfactants are present in the environment at levels below toxicity and in Croatia below the national limit. Most surfactants are readily biodegradable and their amount is greatly reduced with secondary treatment in wastewater treatment plants. The highest concern is the release of untreated wastewater or wastewater that has undergone primary treatment alone. The discharge of wastewater polluted with massive quantities of surfactants could have serious effects on the ecosystem. Future studies of surfactant toxicities and biodegradation are necessary to withdraw highly toxic and non-biodegradable compounds from commercial use and replace them with more environmentally friendly ones.

  17. Pulmonary surfactant and lung transplantation

    NARCIS (Netherlands)

    Erasmus, Michiel Elardus

    1997-01-01

    Pulmonary surfactant lowers the surface tension at the air-water interface inside the alveolus. This is achieved by adsorption of surfactant phospholipids at the air-water interface, a process controlled by surfactant-associated proteins, such as SP-A. In this way, surfactant prevents collapse of th

  18. Metathesis depolymerizable surfactants

    Science.gov (United States)

    Jamison, Gregory M.; Wheeler, David R.; Loy, Douglas A.; Simmons, Blake A.; Long, Timothy M.; McElhanon, James R.; Rahimian, Kamyar; Staiger, Chad L.

    2008-04-15

    A class of surfactant molecules whose structure includes regularly spaced unsaturation in the tail group and thus, can be readily decomposed by ring-closing metathesis, and particularly by the action of a transition metal catalyst, to form small molecule products. These small molecules are designed to have increased volatility and/or enhanced solubility as compared to the original surfactant molecule and are thus easily removed by solvent extraction or vacuum extraction at low temperature. By producing easily removable decomposition products, the surfactant molecules become particularly desirable as template structures for preparing meso- and microstructural materials with tailored properties.

  19. Static and dynamic investigations of poly(aspartic acid) and Pluronic F127 complex prepared by self-assembling in aqueous solution

    Science.gov (United States)

    Nita, Loredana E.; Chiriac, Aurica P.; Bercea, Maria; Nistor, Manuela T.

    2015-12-01

    The present investigation is focused on evaluation of self-assembling ability in aqueous solutions of two water soluble polymers: poly(aspartic acid) (PAS) and Pluronic F127 (PL). The intermolecular complexes, realized between polyacid and neutral copolymer surfactant in different ratios, have been studied by combining various characterization techniques as rheology, DLS, spectroscopy, microscopy, chemical imaging, and zeta potential determination, measurements performed in static and/or dynamic conditions. In static conditions, when the equilibrium state between PAS/PL polymeric pair was reached, and depending on the polymers mixture composition, and of experimental rheological conditions, positive or negative deviations from the additive rule are registered. Conformational changes of the macromolecular chains and correspondingly physical interactions are generated between PL and PAS for self-assembly and the formation of interpolymer complex as suprastructure with micellar configuration. The phenomenon was better evidenced in case of 1/1 wt ratio between the two polymers. In dynamic conditions of determination, during "in situ" evaluation of the hydrodynamic diameter, zeta potential and conductivity, when the equilibrium state is not reached and as result either the intermolecular bonds are not achieved, the self-assembling process is not so obvious evidenced.

  20. Targeting ligand-functionalized and redox-sensitive heparin-Pluronic nanogels for intracellular protein delivery

    Energy Technology Data Exchange (ETDEWEB)

    Nguyen, Dai Hai; Joung, Yoon Ki; Choi, Jong Hoon; Park, Ki Dong [Department of Molecular Science and Technology, Ajou University, 5 Wonchon, Yeoungtong, Suwon 443-749 (Korea, Republic of); Moon, Hyun Tae, E-mail: kdp@ajou.ac.kr [Research Institute of Pharmaceutical Science, College of Pharmacy, Seoul National University, Seoul 151-742 (Korea, Republic of)

    2011-10-15

    The heparin-Pluronic (HP) conjugate was coupled via redox-sensitive disulfide bond and contains a vinyl sulfone (VS) group with high reactivity to some functional groups such as thiol group. Heparin was conjugated with cystamine and the terminal hydroxyl groups of Pluronic were activated with the VS group, followed by coupling of VS groups of Pluronic with cystamine of heparin. The chemical structure, heparin content and VS group content of the resulting product were determined by {sup 1}H NMR, FT-IR, toluidine blue assay and Ellman's method. The HP conjugate formed a type of nanogel in an aqueous medium, showing a critical micelle concentration of approximately 129.35 mg L{sup -1}, a spherical shape and the mean diameter of 115.7 nm, which were measured by AFM and DLS. The release test demonstrated that HP nanogel was rapidly degraded when treated with glutathione. Cytotoxicity results showed a higher viability of drug-free HP nanogel than that of drug-loaded one. Cyclo(Arg-Gly-Asp-D-Phe-Cys) (cRGDfC) peptide was efficiently conjugated to VS groups of HP nanogel and exhibited higher cellular uptake than unmodified nanogels. All results suggest a novel multi-functional nanocarrier delivery and effective release of proteins to the intracellular region in a redox-sensitive manner.

  1. Study on binding and fluorescence energy transfer efficiency of Rhodamine B with Pluronic F127-gold nanohybrid using optical spectroscopy methods

    Science.gov (United States)

    Antonisamy, Jenif Dsouza; Swain, Jitendriya; Dash, Sasmita

    2017-02-01

    This work focuses on the binding efficiency and fluorescence resonance energy transfer (FRET) of fluorescent dye Rhodamine B (Rh B) to Pluronic F127-gold nanohybrid. The formation of gold nanoparticles inside Rh B doped Pluronic F127 copolymer have been characterized using dynamic light scattering study, HR-TEM images, UV-visible spectra and fluorescence studies. Fluorescence quenching and the constant fluorescence lifetime of the Rhodamine B present in the cavity of Pluronic F127-gold nanohybrid suggested a strong binding ability (3.5 × 103 L mol- 1), static nature of quenching and better energy transfer efficiency of fluorescent dye towards Pluronic F127-gold (Au) nanohybrids.

  2. Phosphine oxide surfactants revisited.

    Science.gov (United States)

    Stubenrauch, Cosima; Preisig, Natalie; Laughlin, Robert G

    2016-04-01

    This review summarizes everything we currently know about the nonionic surfactants alkyl dimethyl (C(n)DMPO) and alkyl diethyl (C(n)DEPO) phosphine oxide (PO surfactants). The review starts with the synthesis and the general properties (Section 2) of these compounds and continues with their interfacial properties (Section 3) such as surface tension, surface rheology, interfacial tension and adsorption at solid surfaces. We discuss studies on thin liquid films and foams stabilized by PO surfactants (Section 4) as well as studies on their self-assembly into lyotropic liquid crystals and microemulsions, respectively (Section 5). We aim at encouraging colleagues from both academia and industry to take on board PO surfactants whenever possible and feasible because of their broad variety of excellent properties.

  3. Washing-resistant surfactant coated surface is able to inhibit pathogenic bacteria adhesion

    Science.gov (United States)

    Treter, Janine; Bonatto, Fernando; Krug, Cristiano; Soares, Gabriel Vieira; Baumvol, Israel Jacob Rabin; Macedo, Alexandre José

    2014-06-01

    Surface-active substances, which are able to organize themselves spontaneously on surfaces, triggering changes in the nature of the solid-liquid interface, are likely to influence microorganism adhesion and biofilm formation. Therefore, this study aimed to evaluate chemical non-ionic surfactants activity against pathogenic microbial biofilms and to cover biomaterial surfaces in order to obtain an anti-infective surface. After testing 11 different surfactants, Pluronic F127 was selected for further studies due to its non-biocidal properties and capability to inhibit up to 90% of biofilm formation of Gram-positive pathogen and its clinical isolates. The coating technique using direct impregnation on the surface showed important antibiofilm formation characteristics, even after extensive washes. Surface roughness and bacterial surface polarity does not influence the adhesion of Staphylococcus epidermidis, however, the material coated surface became extremely hydrophilic. The phenotype of S. epidermidis does not seem to have been affected by the contact with surfactant, reinforcing the evidence that a physical phenomenon is responsible for the activity. This paper presents a simple method of surface coating employing a synthetic surfactant to prevent S. epidermidis biofilm formation.

  4. Effect of temperature gradients on single-strand conformation polymorphism analysis in a capillary electrophoresis system using Pluronic polymer matrix.

    Science.gov (United States)

    Hwang, Hee Sung; Shin, Gi Won; Park, Han Jin; Ryu, Chang Y; Jung, Gyoo Yeol

    2013-09-02

    Capillary electrophoresis-single strand conformation polymorphism (CE-SSCP) analysis is a prominent bioseparation method based on the mobility diversity caused by sequence-induced conformational differences of single-stranded DNA. The use of Pluronic polymer matrix has opened up new opportunities for CE-SSCP, because it improved the resolution for various genetic analyses. However, there still exists a challenge in optimizing Pluronic-based CE-SSCP, because the physical properties of Pluronic solutions are sensitive to temperature, particularly near the gelation temperature, where the viscoelasticity of Pluronic F108 solutions sharply changes from that of a Newtonian fluid to a hydrogel upon heating. We have focused on a set of experiments to control the ambient temperature of the CE system with the aim of enhancing the reliability of the CE-SSCP analysis by using the Applied Biosystems ABI 3130xl genetic analyzer with Pluronic F108 solution matrix. The ambient temperature control allowed us to vary the inlet and outlet portion of the capillary column, while the temperature of the column was kept at 35°C. The resolution to separate 2 single-base-pair-differing DNA fragments was significantly enhanced by changing the temperature from 19 to 30°C. The viscoelastic properties of the F108 solution matrix upon heating were also investigated by ex situ rheological experiments with an effort to reveal how the development of gels in Pluronic solutions affects the resolution of CE-SSCP. We found that the column inlet and outlet temperatures of the capillary column have to be controlled to optimize the resolution in CE-SSCP by using the Pluronic matrix.

  5. Synergistic effect of ZnO nanoparticles and triblock copolymer surfactant on the dynamic and equilibrium oil-water interfacial tension.

    Science.gov (United States)

    Moghadam, Tahereh Fereidooni; Azizian, Saeid

    2014-09-07

    The present study reports the effects of non-ionic surfactant Pluronic F-127 on the equilibrium and dynamic oil-water interfacial tension in the presence of ZnO nanoparticles. The results show that in the presence of nanoparticles, the decrease of interfacial tension is more. The cooperative behavior of F-127 and ZnO nanoparticles especially at low concentrations increases the surfactant efficiency in lowering the interfacial tension. Statistical rate theory (SRT) and mixed diffusion-kinetic controlled model were used for modeling the dynamic interfacial tension data. The modeling results show that the mechanism of surfactant adsorption is controlled with the mixed diffusion-kinetic model. In addition, the influence of the solution pH on the interfacial tension was investigated. Finally, the effects of F-127 on the contact angle in the absence and presence of ZnO was compared.

  6. Influence of triblock copolymer (pluronic F127) on enhancing the physico-chemical properties and photocatalytic response of mesoporous TiO{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    Samsudin, Emy Marlina; Hamid, Sharifah Bee Abd, E-mail: sharifahbee@um.edu.my; Juan, Joon Ching; Basirun, Wan Jefrey

    2015-11-15

    Graphical abstract: - Highlights: • Surfactant-assisted modified TiO{sub 2} with photochemically active {1 0 1} and {0 0 1} surface. • Higher surface area promotes substrate absorption. • Narrowing of band gap via presence of defect energy belt. • Exhibit good photo-excited charges separation. • Improved photo-kinetics of atrazine degradation by a factor of 1.7. - Abstract: The utilization of triblock copolymer, pluronic F127 as a structure directing agent for the preparation of TiO{sub 2} played an important role in enhancing the photocatalytic degradation rate of atrazine by a factor of 1.7. The mesoporous F127-TiO{sub 2} showed significant modification of morphology, particle and crystallite size, and presence of defect energy belt within the catalyst forbidden band as proven via photoluminescence spectra and x-ray photon spectroscopy. Hence the photogenerated carriers have longer lifespan to migrate to the catalyst surface for redox activities. Furtherance, surface reactive {0 0 1} facets proven by the formation of new geometrical single crystal of square and rhombus surfaces in F127-TiO{sub 2} facilitates atrazine degradation as well. The increased surface area of F127-TiO{sub 2} promotes greater atrazine absorption, thus governs improved interaction between absorbed atrazine molecules and surface generated active radicals as a pre-requisite for good photocatalytic activity. Interestingly, using the same synthesis procedure, it was observed that the addition of pluronic F127 significantly affects anatase crystal structure as opposed to the more thermodynamically stable rutile, generating 61% and 25% of total crystallite size modification for anatase and rutile, respectively. However, there were no changes on the final composition of anatase and rutile crystal structure. In overall, enhancement of the photocatalytic degradation of atrazine is ruled out to the following factors (1) modification of geometrical structures and size, (2) narrowing of band

  7. Interactions of Pluronic nanocarriers with 2D and 3D cell cultures: Effects of PEO block length and aggregation state.

    Science.gov (United States)

    Arranja, Alexandra; Denkova, Antonia G; Morawska, Karolina; Waton, Gilles; van Vlierberghe, Sandra; Dubruel, Peter; Schosseler, François; Mendes, Eduardo

    2016-02-28

    This work reveals how the physicochemical properties of Pluronic block copolymers influence significantly their interactions with cancer cells, whether in monolayer or spheroid cultures, and how different clinical applications can be foreseen. Two-dimensional (2D) and three-dimensional (3D) cell culture models were used to investigate the interactions of Pluronic carriers with different PEO block length and aggregation state (unimers versus cross-linked micelles) in HeLa and U87 cancer cells. Stabilized micelles of Pluronic P94 or F127 were obtained by polymerization of a crosslinking agent in the micelles hydrophobic core. Nanocarriers were functionalized with a fluorescent probe for visualization, and with a chelator for radiolabeling with Indium-111 and gamma-quantification. The 2D cell models revealed that the internalization pathways and ultimate cellular localization of the Pluronic nanocarriers depended largely on both the PEO block size and aggregation state of the copolymers. The smaller P94 unimers with an average radius of 2.1nm and the shortest PEO block mass (1100gmol(-1)) displayed the highest cellular uptake and retention. 3D tumor spheroids were used to assess the penetration capacity and toxicity potential of the nanocarriers. Results showed that cross-linked F127 micelles were more efficiently delivered across the tumor spheroids, and the penetration depth depends mostly on the transcellular transport of the carriers. The Pluronic P94-based carriers with the shortest PEO block length induced spheroid toxicity, which was significantly influenced by the spheroid cellular type.

  8. SPECT/CT Imaging of Pluronic Nanocarriers with Varying Poly(ethylene oxide) Block Length and Aggregation State.

    Science.gov (United States)

    Arranja, Alexandra; Ivashchenko, Oleksandra; Denkova, Antonia G; Morawska, Karolina; van Vlierberghe, Sandra; Dubruel, Peter; Waton, Gilles; Beekman, Freek J; Schosseler, François; Mendes, Eduardo

    2016-03-07

    Optimal biodistribution and prolonged circulation of nanocarriers improve diagnostic and therapeutic effects of enhanced permeability and retention-based nanomedicines. Despite extensive use of Pluronics in polymer-based pharmaceuticals, the influence of different poly(ethylene oxide) (PEO) block length and aggregation state on the biodistribution of the carriers is rather unexplored. In this work, we studied these effects by evaluating the biodistribution of Pluronic unimers and cross-linked micelles with different PEO block size. In vivo biodistribution of (111)In-radiolabeled Pluronic nanocarriers was investigated in healthy mice using single photon emission computed tomography. All carriers show fast uptake in the organs from the reticuloendothelial system followed by a steady elimination through the hepatobiliary tract and renal filtration. The PEO block length affects the initial renal clearance of the compounds and the overall liver uptake. The aggregation state influences the long-term accumulation of the nanocarriers in the liver. We showed that the circulation time and elimination pathways can be tuned by varying the physicochemical properties of Pluronic copolymers. Our results can be beneficial for the design of future Pluronic-based nanomedicines.

  9. Novel strategy involving surfactant-polymer combinations for enhanced stability of aqueous teflon dispersions.

    Science.gov (United States)

    Sharma, Mukesh; Bharatiya, Bhavesh; Mehta, Krupali; Shukla, Atindra; Shah, Dinesh O

    2014-06-24

    Among various polymers, the Teflon surface possesses extreme hydrophobicity (low surface energy), which is of great interest to both industry and academia. In this report, we discuss the stability of aqueous Teflon dispersions (particle size range of 100-3000 nm) formulated by a novel strategy that involves distinct combinations of surfactant and polymer mixtures for dispersion stabilization. As a first step, the hydrophobic Teflon particles were wetted using a range of surfactants (ionic, Triton, Brij, Tween, and Pluronic series) bearing different hydrophobic-lipophilic balance (HLB) and further characterized by contact angle and liquid penetration in packed powder measurements. The interaction between hydrophobic chains of surfactants and the Teflon particle surface is the driving force resulting in wetting of the Teflon particle surface. Further, these wetted particles in aqueous solutions were mixed with various polymers, for example, poly(vinyl alcohol) (PVA), polyvinylpyrrolidone (PVP), hydroxyethyl cellulose (HEC), and hydroxypropyl methyl cellulose (HPMC). The rate of sedimentation for the final dispersions was measured using a pan suspended into the dispersion from a transducer recording the increase in weight with time. A significant stability was noticed for Teflon particles suspended in surfactant + polymer mixtures, which was linearly proportional to the concentration of added polymer. The observed phenomenon can be possibly explained by molecular interactions between the hydrophobic chains of surfactant molecules and polar groups in the polymer architecture. Brij-O10 + HEC mixture was found to be the best surfactant-polymer combination for decreasing the sedimentation of the Teflon particles in the final dispersion. As measured by dynamic light scattering (DLS), the hydrodynamic volume of the Teflon particles increases up to ∼55% in the final formulation. These dispersions could be further explored for various technological applications such as

  10. Surfactant-Amino Acid and Surfactant-Surfactant Interactions in Aqueous Medium: a Review.

    Science.gov (United States)

    Malik, Nisar Ahmad

    2015-08-01

    An overview of surfactant-amino acid interactions mainly in aqueous medium has been discussed. Main emphasis has been on the solution thermodynamics and solute-solvent interactions. Almost all available data on the topic has been presented in a lucid and simple way. Conventional surfactants have been discussed as amphiphiles forming micelles and amino acids as additives and their effect on the various physicochemical properties of these conventional surfactants. Surfactant-surfactant interactions in aqueous medium, various mixed surfactant models, are also highlighted to assess their interactions in aqueous medium. Finally, their applied part has been taken into consideration to interpret their possible uses.

  11. Khảo sát sự tạo mixel của một số Copolyme Pluronic

    DEFF Research Database (Denmark)

    Hùng, Nguyễn Quốc; Hvidt, Søren; Batsberg, Walther;

    2009-01-01

    The micellization of several Pluronics (PEO-PPO-PEO triblock copolymers) was investigated by Differential Scanning Calorimetry (DSC). These copolymers were also characterized and purified by liquid chromatography. The PEO/PPO compositions of Pluronics were determined by 1H-NMR. The thermograms from...

  12. Khảo sát sự tạo mixel của một số Copolyme Pluronic

    DEFF Research Database (Denmark)

    Hùng, Nguyễn Quốc; Hvidt, Søren; Batsberg, Walther

    2009-01-01

    The micellization of several Pluronics (PEO-PPO-PEO triblock copolymers) was investigated by Differential Scanning Calorimetry (DSC). These copolymers were also characterized and purified by liquid chromatography. The PEO/PPO compositions of Pluronics were determined by 1H-NMR. The thermograms from...

  13. Formulation and evaluation of novel controlled release of topical pluronic lecithin organogel of mefenamic acid.

    Science.gov (United States)

    Jhawat, Vikas; Gupta, Sumeet; Saini, Vipin

    2016-11-01

    In the present study, pluronic lecithin based organogels (PLO gels) were formulated as topical carrier for controlled delivery of mefenamic acid. Ten organogel formulations were prepared by a method employing lecithin as lipophilic phase and pluronic F-127 as hydrophilic phase in varying concentrations to study various parameters using in vitro diffusion study and in vivo studies. All formulations were found to be off-white, homogenous, and reluctant to be washed easily and have pH value within the range of 5.56-5.80 which is nonirritant. Polymer concentration increased in formulations of F1 to F5 (lecithin) and F6 to F10 (pluronic) resulted in decrease of the gelation temperature, increase of viscosity and reduction of spreadability of gels having polymer tendency to form rigid 3D network. Organogels with higher viscosity were found to be more stable and retard the drug release from the gel. The formulations of F2 and F3 were selected for kinetic studies and stability studies, as they found to have all physical parameters within acceptable limits, highest percent drug content and exhibited highest drug release in eight hours. The order of drug release from various formulations was found to be F2 > F3 > F10 > F4 > F1 > F9 > F8 > F5 > F7 > F6. The optimized formulation F2 was found to follow zero order rate kinetics showing controlled release of the drug from the formulations. In vivo anti-inflammatory activity of optimized mefenamic acid organogel (F2) against a standard marketed preparation (Volini gel) was found satisfactory and significant.

  14. A fluorescence study on the interaction of telmisartan in triblock polymers pluronic P123 and F127

    Science.gov (United States)

    Mohanty, Maneesha Esther; Rao, Vaidya Jayathirtha; Mishra, Ashok Kumar

    2014-03-01

    Telmisartan is a poorly soluble drug used in treatment of hypertension. There is a recent interest to use pluronic for improving the solubility and bioavailability of these drugs. In this study the interaction of telmisartan with P123 and F127 has been carried out using steady state and time dependent fluorescence study. Quenching of telmisartan fluorescence by potassium iodide is controlled by interactions arising from collisions and complex formation. A comparison of the fluorescence of telmisartan in pluronics with the well understood fluorescence of 8-anilino-1-naphthalene-sulfonic acid, a known fluorescent molecular probe, indicates that telmisartan is generally present in a relatively polar microenvironment with restricted diffusive motion.

  15. Characterization of chlorophyll derivatives in micelles of polymeric surfactants aiming photodynamic applications

    Science.gov (United States)

    Gerola, Adriana Passarella; de Morais, Flavia Amanda Pedroso; Costa, Paulo Fernando A.; Kimura, Elza; Caetano, Wilker; Hioka, Noboru

    2017-02-01

    The spectrophotometric properties of chlorophylls' derivatives (Chls) formulated in the Pluronics® F-127 and P-123 were evaluated and the results have shown that the Chls were efficiently solubilized in these drug delivery systems as monomers. The relative location of the Chls in the Pluronics® was estimated from the Stokes shift and micropolarity of the micellar environment. Chls with phytyl chain were located in the micellar core, where the micropolarity is similar to ethanol, while phorbides' derivatives (without phytyl chain) were located in the outer shell of the micelle, i.e., more polar environment. In addition, the thermal stability of the micellar formulations was evaluated through electronic absorption, fluorescence emission and resonance light scattering with lowering the temperature. The Chls promote the stability of the micelles at temperatures below the Critical Micellar Temperature (CMT) of these surfactants. For F-127 formulations, the water molecules drive through inside the nano-structure at temperatures below the CMT, which increased the polarity of this microenvironment and directly affected the spectrophotometric properties of the Chls with phytyl chain. The properties of the micellar microenvironment of P-123, with more hydrophobic core due to the small PEO/PPO fraction, were less affected by lowering the temperature than for F-127. These results enable us to better understand the Chls behavior in micellar copolymers and allowed us to design new drug delivery system that maintains the photosensitizer's properties for photodynamic applications.

  16. Sizing up surfactant synthesis.

    Science.gov (United States)

    Han, SeungHye; Mallampalli, Rama K

    2014-08-01

    Phosphatidylcholine is generated through de novo synthesis and remodeling involving a lysophospholipid. In this issue of Cell Metabolism, research from the Shimizu lab (Harayama et al., 2014) demonstrates the highly selective enzymatic behavior of lysophospholipid acyltransferases. The authors present an enzymatic model for phosphatidylcholine molecular species diversification that impacts surfactant formation.

  17. Preparation of nanocrystalline MgO by surfactant assisted precipitation method

    Energy Technology Data Exchange (ETDEWEB)

    Rezaei, Mehran, E-mail: rezaei@kashanu.ac.ir [Catalyst and Advanced Materials Research Laboratory, Chemical Engineering Department, Faculty of Engineering, University of Kashan, Kashan (Iran, Islamic Republic of); Institute of Nanoscience and Nanotechnology, University of Kashan, Kashan (Iran, Islamic Republic of); Khajenoori, Majid; Nematollahi, Behzad [Catalyst and Advanced Materials Research Laboratory, Chemical Engineering Department, Faculty of Engineering, University of Kashan, Kashan (Iran, Islamic Republic of)

    2011-10-15

    Highlights: {yields} Nanocrystalline magnesium oxide with high surface area. {yields} MgO prepared with surfactant showed different morphologies compared with the sample prepared without surfactant. {yields} MgO prepared with surfactant showed a plate-like shape. {yields} Refluxing temperature and time and the surfactant to metal molar ratio affect the textural properties of MgO. -- Abstract: Nanocrystalline magnesium oxide with high surface area was prepared by a simple precipitation method using pluronic P123 triblock copolymer (Poly (ethylene glycol)-block, Poly (propylene glycol)-block, Poly (ethylene glycol)) as surfactant and under refluxing conditions. The prepared samples were characterized by X-ray diffraction (XRD), N{sub 2} adsorption (BET) and scanning and transmission electron microscopies (SEM and TEM). The obtained results revealed that the refluxing time and temperature and the molar ratio of surfactant to metal affect the structural properties of MgO, because of the changes in the rate and extent of P123 adsorption on the prepared samples. The results showed that the addition of surfactant is effective to prepare magnesium oxide with high surface area and affects the morphology of the prepared samples. With increasing the P123/MgO molar ratio to 0.05 the pore size distribution was shifted to larger size. The sample prepared with addition of surfactant showed a plate-like shape which was completely different with the morphology of the sample prepared without surfactant. The formation of nanoplate-like MgO was related to higher surface density of Mg ions on the (0 0 1) plane than that on the other planes of the Mg(OH){sub 2} crystal. The (0 0 1) plane would be blocked preferentially by the adsorbed P123 molecules during the growing process of Mg(OH){sub 2} nanoentities and the growth on the (0 0 1) plane would be markedly restricted, and the consequence is the generation of nanoplate-like MgO. In addition, increase in refluxing temperature and time

  18. Pluronic® coated sterically stabilized magnetite nanoparticles for hyperthermia applications

    Science.gov (United States)

    Rodrigues, E. C.; Morales, M. A.; de Medeiros, S. N.; Suguihiro, N. M.; Baggio-Saitovitch, E. M.

    2016-10-01

    We report the synthesis of magnetite nanoparticles by ball milling of α-Fe in water and its functionalization with oleic acid and Pluronic® F127 for use in hyperthermia applications. The samples were characterized by transmission electron microscopy, DC magnetometry, X-ray diffraction, infrared spectroscopy and heat release studies under an AC magnetic field. The magnetite phase corresponded to 96 wt% and there was a small contribution of 4 wt% of α-Fe. The magnetite particles have a main size of 22 nm and oleic acid layer thickness of 1.9 nm. Magnetic measurements indicate the particles are blocked at 300 K and exhibit the Verwey transition at 119 K. At 5 K the saturation magnetization obtained from the law of approach to saturation was of 95 emu/g. In the heat release studies, the sterically stabilized particles have a temperature increase, ΔT, of 43 °C in 350 s. The Pluronic® coated particles, dispersed in water at 50 mg/ml, exhibited a ΔT=10.5 °C in 350 s, and this value remained nearly constant for periods of up to 650 s. The specific absorption rate (SAR) was of 6.4 W/g indicating that this sample may be used for the lyse of tumor cells.

  19. Modulating Pluronics micellar rupture with cyclodextrins and drugs: effect of pH and temperature

    Science.gov (United States)

    Valero, M.; Dreiss, C. A.

    2014-11-01

    Micelles of the triblock copolymer Pluronic F127 can encapsulate drugs with various chemical structures and their architecture has been studied by small-angle neutron scattering (SANS). Interaction with a derivative of β-cyclodextrin, namely, heptakis(2,6-di-O- methyl)-β-cyclodextrin (DIMEB), induces a complete break-up of the micelles, providing a mechanism for drug release. In the presence of drugs partitioned within the micelles, competitive interactions between polymer, drug and cyclodextrin lead to a modulation of the micellar rupture, depending on the nature of the drug and the exact composition of the ternary system. These interactions can be further adjusted by temperature and pH. While the most widely accepted mechanism for the interaction between Pluronics and cyclodextrins is through polypseudorotaxane (PR) formation, involving the threading of β-CD on the polymer backbone, time-resolved SANS experiments show that de-micellisation takes place in less than 100 ms, thus unambiguously ruling out an inclusion complex between the cyclodextrin and the polymer chains.

  20. Structural characterization and adsorption properties of pluronic F127 onto iron oxides magnetic nanoparticles.

    Science.gov (United States)

    Dehvari, Khalilalrahman; Lin, Kuen-Song; Wang, Steven S S

    2014-03-01

    Superparamagnetic iron oxide nanoparticles coated with polymers have shown low toxicity and chemical stability in physiological condition, thereby can be used to deliver encapsulated drugs throughout the body by external magnetic fields. In this study, magnetic nanoparticles were synthesized thorough co-precipitation method and their interaction with Pluronic F127 block copolymer as well as adsorption properties of polymer onto nanoparticles were investigated. Adsorption measurement revealed different adsorption behaviors below and above the polymer's critical micelle concentration. The Freundlich isotherm was found to better describe the adsorption behavior of Pluronic F127 onto SIONPs particles below the block copolymer critical micelle concentration. At higher concentration, the adsorbed amount is likely to diminish due to interpenetration of the adsorbed macromolecular micelles and volume-excluded effects for block copolymers. Furthermore, magnetic nanocomposites with different concentration of polymers were prepared through hydrothermal method. The crystalline structure, morphology, pore structure, and magnetic properties of magnetic nanoparticles/nanocomposites products at different pH and polymer concentration were studied. Results showed that due to the hematite impurities, magnetic nanocomposites synthesized at higher pH have lower magnetization.

  1. Statistical optimization of insulin-loaded Pluronic F-127 gels for buccal delivery of basal insulin.

    Science.gov (United States)

    Das, Nilanjana; Madan, Parshotam; Lin, Senshang

    2012-01-01

    The principle of statistical optimization was employed to fabricate insulin-loaded Pluronic F-127 (PF-127) gel formulations having the potential for buccal delivery of basal insulin. A two-level resolution III fractional factorial design was applied to simultaneously evaluate five independent formulation variables: PF-127 concentration, insulin concentration, sodium sulfate concentration, hydroxypropylmethyl cellulose (HPMC) concentration, and presence of sodium glycocholate. The amount of insulin released and permeated from gels as well as gelation time and mucoadhesion force of gels were measured and used as dependent response variables for formulation optimization. Optimization of a gel formulation was achieved by applying constrained optimization via regression analysis. In vitro permeation flux of insulin from the optimized formulation through procine buccal mucosa was 93.17 (±0.058, n = 3) μg/cm(2). Plasma insulin levels following buccal administration of the optimized formulation at 10, 25 and 50 IU/kg to healthy rats were found to be dose dependent and basal insulin levels were maintained at least for 8 h. Furthermore, continuous hypoglycemia for at least 8 h was observed with 89%, 51% and 25% of blood glucose reduction, respectively, for these three doses. The results of this investigation conclude the feasibility of development of optimized buccal insulin-loaded Pluronic F-127 gels for basal insulin delivery.

  2. Development and in vitro evaluation of insulin-loaded buccal Pluronic F-127 gels.

    Science.gov (United States)

    Das, Nilanjana; Madan, Parshotam; Lin, Senshang

    2010-01-01

    Insulin-loaded buccal Pluronic F-127 (PF-127) gel formulations were fabricated to study the effect of PF-127 concentration, insulin concentration, presence of salt, addition of polymer, and permeation enhancer on their gelation time, mucoadhesion force, release and permeation characteristics of insulin from the gels. Thereafter, the principle of statistical optimization to prepare a gel formulation having the potential for buccal delivery of basal insulin in diabetic patients was employed. The gelation time decreased as the concentration of PF-127 increased. Presence of salts as well as addition of polymer, such as methyl cellulose (MC) and hydroxypropylmethyl cellulose (HPMC) decreased the gelation time. An increase in PF-127 concentration and addition of MC and HPMC increased the mucoadhesion force of the gel formulations. Release and permeation of insulin from the gel formulations decreased with increased concentration of PF-127, presence of salts, and addition of MC and HPMC. Permeation of insulin from the optimized gel formulation was 93.17 (+/- 0.058, n = 3) microg/cm(2) which was not only found in close agreement with predicted results from the model equations used for the formulation optimization but also considered comparable to clinical setting. Therefore, the development of optimized buccal insulin-loaded Pluronic F-127 gels using a statistical experimental design is feasible.

  3. Adsorption of Pluronic F-127 on Surfaces with Different Hydrophobicities Probed by Quartz Crystal Microbalance with Dissipation

    NARCIS (Netherlands)

    Nejadnik, M.R.; Olsson, A.L.J.; Sharma, P.K.; Mei, van der H.C.; Norde, W.; Busscher, H.J.

    2009-01-01

    Triblock copolymers of polyethylene oxide (PEO) and polypropylene oxide (PPO), that is, PEOn-PPOm-PEOn, better known as Pluronic can adsorb to surfaces in either a pancake or a brushlike configuration. The brushlike configuration is advantageous in numerous applications, since it constitutes a

  4. Melatonin-loaded chitosan/Pluronic® F127 microspheres as in situ forming hydrogel: An innovative antimicrobial wound dressing.

    Science.gov (United States)

    Romić, Marieta Duvnjak; Klarić, Maja Šegvić; Lovrić, Jasmina; Pepić, Ivan; Cetina-Čižmek, Biserka; Filipović-Grčić, Jelena; Hafner, Anita

    2016-10-01

    The aim of this study was to develop melatonin-loaded chitosan based microspheres as dry powder formulation suitable for wound dressing, rapidly forming hydrogel in contact with wound exudate. Microspheres were produced by spray-drying method. Fractional factorial design was employed to elucidate the effect of formulation and process parameters (feed flow rate, inlet air temperature, chitosan concentration, chitosan/melatonin ratio and chitosan/Pluronic® F127 ratio) on the product characteristics related to process applicability (production yield, entrapment efficiency and product moisture content) and microsphere performance in biological environment (microsphere mean diameter and surface charge). Appropriate formulation and process parameters for the establishment of efficient drying process resulting in fine-tuned chitosan and chitosan/Pluronic® F127 microspheres (efficient melatonin encapsulation, small diameter positive surface charge and low moisture content) were identified. Microspheres were characterized by appropriate flowability and high rate and extent of fluid uptake. Incorporation of Pluronic® F127 in microsphere matrix resulted in high melatonin amorphization and consequent higher melatonin release rate. Entrapment of melatonin in chitosan/Pluronic® F127 microspheres has potentiated chitosan antimicrobial activity against Staphylococcus aureus and five clinical isolates S. aureus MRSA strains. Microspheres were shown to be biocompatible with skin keratinocytes and fibroblasts at concentrations relevant for antimicrobial activity against planktonic bacteria.

  5. Evaluation of the stability of ketoprofen in pluronic lecithin organogel and the determination of an appropriate beyond-use date.

    Science.gov (United States)

    Peacock, Gina F; Sauvageot, Jurgita; Addo, Richard T

    2014-01-01

    Previous reports indicate that pharmacists are assigning a wide variety of beyond-use dates to extemporaneously compounded medications in topical Pluronic lecithin organogel. The objective of this study was to evaluate the stability of ketoprofen in Pluronic lecithin organogel over a period of six months and to determine an appropriate beyond-use date for this formulation. A stability-indicating high-performance liquid chromatography method for ketoprofen in Pluronic lecithin organogel was validated in our laboratory. Samples of the formulation were analyzed by high-performance liquid chromatography at 0, 7, 14, 21, 28, 45, 60, 90, and 180 days. At each time point, the average concentration and average percent of initial concentration were calculated. The beyond-use date was determined as the time period that the samples were physically stable and maintained at least 90% of the initial concentration. Ketoprofen in Pluronic lecithin organogel was chemically and physically stable for six months when stored at room temperature and protected from light. Therefore, a beyond-use date of six months is appropriate for this preparation.

  6. Evaluation of the effect of a gamma irradiated DBM-pluronic F127 composite on bone regeneration in Wistar rat.

    Directory of Open Access Journals (Sweden)

    Tamer Al Kayal

    Full Text Available Demineralized bone matrix (DBM is widely used for bone regeneration. Since DBM is prepared in powder form its handling properties are not optimal and limit the clinical use of this material. Various synthetic and biological carriers have been used to enhance the DBM handling. In this study we evaluated the effect of gamma irradiation on the physical-chemical properties of Pluronic and on bone morphogenetic proteins (BMPs amount in DBM samples. In vivo studies were carried out to investigate the effect on bone regeneration of a gamma irradiated DBM-Pluronic F127 (DBM-PF127 composite implanted in the femur of rats. Gamma irradiation effects (25 kGy on physical-chemical properties of Pluronic F127 were investigated by rheological and infrared analysis. The BMP-2/BMP-7 amount after DBM irradiation was evaluated by ELISA. Bone regeneration capacity of DBM-PF127 containing 40% (w/w of DBM was investigated in transcortical holes created in the femoral diaphysis of Wistar rat. Bone porosity, repaired bone volume and tissue organization were evaluated at 15, 30 and 90 days by Micro-CT and histological analysis. The results showed that gamma irradiation did not induce significant modification on physical-chemical properties of Pluronic, while a decrease in BMP-2/BMP-7 amount was evidenced in sterilized DBM. Micro-CT and histological evaluation at day 15 post-implantation revealed an interconnected trabeculae network in medullar cavity and cellular infiltration and vascularization of DBM-PF127 residue. In contrast a large rate of not connected trabeculae was observed in Pluronic filled and unfilled defects. At 30 and 90 days the DBM-PF127 samples shown comparable results in term of density and thickness of the new formed tissue respect to unfilled defect. In conclusion a gamma irradiated DBM-PF127 composite, although it may have undergone a significant decrease in the concentration of BMPs, was able to maintains bone regeneration capability.

  7. Ultrasound-stimulated peripheral nerve regeneration within asymmetrically porous PLGA/Pluronic F127 nerve guide conduit.

    Science.gov (United States)

    Park, Sang Chul; Oh, Se Heang; Seo, Tae Beom; Namgung, Uk; Kim, Jin Man; Lee, Jin Ho

    2010-08-01

    Recently, we developed a novel method to fabricate a nerve guide conduit (NGC) with asymmetrical pore structure and hydrophilicity using poly(lactic-co-glycolic acid) (PLGA) and Pluronic F127 by a modified immersion precipitation method. From the animal study using a rat model (sciatic nerve defect of rat), we recognized that the unique PLGA/Pluronic F127 tube provided good environments for nerve regeneration. In this study, we applied low-intensity pulsed ultrasound as a simple and noninvasive stimulus at the PLGA/F127 NGC-implanted site transcutaneously in rats to investigate the feasibility of ultrasound for the enhanced nerve regeneration through the tube. The nerve regeneration behaviors within the ultrasound-stimulated PLGA/Pluronic F127 NGCs were compared with the NGCs without the ultrasound treatment as well as normal nerve by histological and immunohistochemical observations. It was observed that the PLGA/Pluronic F127 tube-implanted group applied with the ultrasound had more rapid nerve regeneration behavior (approximately 0.71 mm/day) than the tube-implanted group without the ultrasound treatment (approximately 0.48 mm/day). The ultrasound-treated tube group also showed greater neural tissue area as well as larger axon diameter and thicker myelin sheath than the tube group without the ultrasound treatment, indicating better nerve regeneration. The better nerve regeneration behavior in the our NGC/ultrasound system may be caused by the synergistic effect of the asymmetrically porous PLGA/Pluronic F127 tube with unique properties (selective permeability, hydrophilicity, and structural stability, which can provide good environment for nerve regeneration) and physical stimulus (stimulation of the Schwann cells and activation of the neurotrophic factors).

  8. Modeling the Phase Behavior of PEO-PPO-PEO Surfactants in Carbon Dioxide Using the PC-SAFT Equation of State: Application to Dry Decontamination of Solid Substrates

    Energy Technology Data Exchange (ETDEWEB)

    Kleiner, M.; Sadowski, G. [Tech Univ Dortmund, Dept Biochem and Chem Engn, Lab Thermodynam, D-44227 Dortmund (Germany); Stoychev, I.; Galy, J. [CEA Marcoule, DEN, DTCD, SPDE, LFSM, 30 (France); Fournel, B. [CEA Marcoule, DEN, DTCD, DIR, 30 (France); Lacroix-Desmazes, P. [ENSCM, UM2, UM1, CNRS, Inst Charles Gerhardt, UMR IAM 5253, F-34296 Montpellier 5 (France)

    2009-05-15

    The phase behavior of several commercially available poly(ethylene oxide)-b-poly(propylene oxide)-b-poly(ethylene oxide) block copolymers (PEO-PPO-PEO or Pluronics L) in compressed carbon dioxide has been investigated within the framework of dry nuclear decontamination. For this purpose, cloud points have been measured in the pressure and temperature range from P = (10 to 40) MPa and from T = (293 to 338) K, respectively. To find a reliable method for surfactant selection, the perturbed-chain statistical association fluid theory (PC-SAFT) equation of state (EoS) has been applied to model the experimental data. The pure-component and the respective homopolymer + CO{sub 2} binary interaction parameters have been fitted to liquid densities and to homopolymer + CO{sub 2} binary equilibrium data. The phase behavior of Pluronics L copolymers as a function of concentration, molar mass, and copolymer composition has been predicted very accurately using a constant PEO-PPO binary interaction parameter k(PEO-PPO) = 0.007. The P and SAFT model was also successfully applied to Pluronics R copolymers (PPO-PEO-PPO), although a different k(PEO-PPO) = -0.018 was required to match the experimental data. The model predictions have shown that Pluronics L copolymers with molar mass M {<=} 2750 g.mol{sup -1} and a PEO mass fraction in the copolymer of less than 30 % have sufficiently low cloud-point pressures and are therefore the most suitable for the decontamination process. (authors)

  9. Pluronics-Formulated Farnesol Promotes Efficient Killing and Demonstrates Novel Interactions with Streptococcus mutans Biofilms.

    Science.gov (United States)

    Mogen, Austin B; Chen, Fu; Ahn, Sang-Joon; Burne, Robert A; Wang, Dong; Rice, Kelly C

    2015-01-01

    Streptococcus mutans is the primary causative agent of dental caries, one of the most prevalent diseases in the United States. Previously published studies have shown that Pluronic-based tooth-binding micelles carrying hydrophobic antimicrobials are extremely effective at inhibiting S. mutans biofilm growth on hydroxyapatite (HA). Interestingly, these studies also demonstrated that non-binding micelles (NBM) carrying antimicrobial also had an inhibitory effect, leading to the hypothesis that the Pluronic micelles themselves may interact with the biofilm. To explore this potential interaction, three different S. mutans strains were each grown as biofilm in tissue culture plates, either untreated or supplemented with NBM alone (P85), NBM containing farnesol (P85F), or farnesol alone (F). In each tested S. mutans strain, biomass was significantly decreased (SNK test, p < 0.05) in the P85F and F biofilms relative to untreated biofilms. Furthermore, the P85F biofilms formed large towers containing dead cells that were not observed in the other treatment conditions. Tower formation appeared to be specific to formulated farnesol, as this phenomenon was not observed in S. mutans biofilms grown with NBM containing triclosan. Parallel CFU/ml determinations revealed that biofilm growth in the presence of P85F resulted in a 3-log reduction in viability, whereas F decreased viability by less than 1-log. Wild-type biofilms grown in the absence of sucrose or gtfBC mutant biofilms grown in the presence of sucrose did not form towers. However, increased cell killing with P85F was still observed, suggesting that cell killing is independent of tower formation. Finally, repeated treatment of pre-formed biofilms with P85F was able to elicit a 2-log reduction in viability, whereas parallel treatment with F alone only reduced viability by 0.5-log. Collectively, these results suggest that Pluronics-formulated farnesol induces alterations in biofilm architecture, presumably via interaction

  10. Pluronics-Formulated Farnesol Promotes Efficient Killing and Demonstrates Novel Interactions with Streptococcus mutans Biofilms.

    Directory of Open Access Journals (Sweden)

    Austin B Mogen

    Full Text Available Streptococcus mutans is the primary causative agent of dental caries, one of the most prevalent diseases in the United States. Previously published studies have shown that Pluronic-based tooth-binding micelles carrying hydrophobic antimicrobials are extremely effective at inhibiting S. mutans biofilm growth on hydroxyapatite (HA. Interestingly, these studies also demonstrated that non-binding micelles (NBM carrying antimicrobial also had an inhibitory effect, leading to the hypothesis that the Pluronic micelles themselves may interact with the biofilm. To explore this potential interaction, three different S. mutans strains were each grown as biofilm in tissue culture plates, either untreated or supplemented with NBM alone (P85, NBM containing farnesol (P85F, or farnesol alone (F. In each tested S. mutans strain, biomass was significantly decreased (SNK test, p < 0.05 in the P85F and F biofilms relative to untreated biofilms. Furthermore, the P85F biofilms formed large towers containing dead cells that were not observed in the other treatment conditions. Tower formation appeared to be specific to formulated farnesol, as this phenomenon was not observed in S. mutans biofilms grown with NBM containing triclosan. Parallel CFU/ml determinations revealed that biofilm growth in the presence of P85F resulted in a 3-log reduction in viability, whereas F decreased viability by less than 1-log. Wild-type biofilms grown in the absence of sucrose or gtfBC mutant biofilms grown in the presence of sucrose did not form towers. However, increased cell killing with P85F was still observed, suggesting that cell killing is independent of tower formation. Finally, repeated treatment of pre-formed biofilms with P85F was able to elicit a 2-log reduction in viability, whereas parallel treatment with F alone only reduced viability by 0.5-log. Collectively, these results suggest that Pluronics-formulated farnesol induces alterations in biofilm architecture, presumably

  11. Chitosan–Pluronic nanoparticles as oral delivery of anticancer gemcitabine: preparation and in vitro study

    Directory of Open Access Journals (Sweden)

    Ostad SN

    2012-04-01

    Full Text Available Hosniyeh Hosseinzadeh1, Fatemeh Atyabi1, Rassoul Dinarvand1, Seyed Naser Ostad21Nanotechnology Research Centre, 2Department of Toxicology and Pharmacology, Faculty of Pharmacy, Tehran University of Medical Sciences, Tehran, IranAbstract: Nanoparticles have proven to be an effective delivery system with few side effects for anticancer drugs. In this study, gemcitabine-loaded nanoparticles have been prepared by an ionic gelation method using chitosan and Pluronic® F-127 as a carrier. Prepared nanoparticles were characterized using dynamic light scattering, Fourier transform infrared spectroscopy (FT-IR, differential scanning calorimetry (DSC, scanning electron microscopy, and transmission electron microscopy. Different parameters such as concentration of sodium tripolyphosphate, chitosan, Pluronic, and drug on the properties of the prepared nanoparticles were evaluated. In vitro drug release was studied in phosphate-buffered saline (PBS; pH = 7.4. The cytotoxicity of the nanoparticles was assayed in the HT-29 colon cancer cell line. The mucoadhesion behavior of the nanoparticles was also studied by mucus glycoprotein assay. The prepared nanoparticles had a spherical shape with positive charge and a mean diameter ranging between 80 to 170 nm. FT-IR and DSC studies found that the drug was dispersed in its amorphous form due to its potent interaction with nanoparticle matrix. Maximum drug encapsulation efficiency was achieved at 0.4 mg/mL gemcitabine while maximum drug loading was 6% obtained from 0.6 mg/mL gemcitabine. An in vitro drug release study at 37°C in PBS (pH = 7.4 exhibited a controlled release profile for chitosan–Pluronic® F-127 nanoparticles. A cytotoxicity assay of gemcitabine-loaded nanoparticles showed an increase in the cytotoxicity of gemcitabine embedded in the nanoparticles in comparison with drug alone. The mucoadhesion study results suggest that nanoparticles could be considered as an efficient oral formulation for colon

  12. MICROBIAL SURFACTANTS. I. GLYCOLIPIDS

    Directory of Open Access Journals (Sweden)

    Pirog T. Р.

    2014-02-01

    Full Text Available The review is devoted to surface-active glycolipids. The general characteristics, the physiological role of the rhamnolipids, trehalose lipids, sophorolipids, mannosylerythritol lipids and their traditional producers — the representatives of the genera Pseudozyma, Pseudomonas, Rhodococcus and Candida are given. The detailed analysis of the chemical structure, the stages of the biosynthesis and the regulation of some low molecular glycolipids are done. The own experimental data concerning the synthesis intensification, the physiological role and the practical use of Rhodococcus erythropolis IMV Ac-5017, Acinetobacter calcoaceticus IMV B-7241 and Nocardia vaccinii IMV B-7405 surfactants, which are a complex of the glyco-, phospho-, amino- and neutral lipids (glycolipids of all strains are presented by trehalose mycolates are summarized. It was found that R. erythropolis IMV Ac-5017, A. calcoaceticus IMV B-7241 and N. vaccinii IMV B-7405 surfactants have protective, antimicrobial and antiadhesive properties. It was shown that R. erythropolis IMV Ac-5017, A. calcoaceticus IMV B-7241 and N. vaccinii IMV B-7405 surfactants preparation of cultural liquid intensified the degradation of oil in water due to the activation of the natural petroleum-oxidizing microflora.

  13. MICROBIAL SURFACTANTS. II. LIPOPEPTIDES

    Directory of Open Access Journals (Sweden)

    T. P. Pirog

    2014-04-01

    Full Text Available The classification and the chemical structure of the lipopeptides and their producers (bacteria of the genera Bacillus and Pseudomonas are given. The role of the lipopeptides in cells motility, biofilm formation, metal binding and xenobiotics degradation and their action on the cells of pro- and eukaryotes is summarized. The stages of the nonribosomal lipopeptides synthesis and the role of two-component (GacA/GacS, ComA/ComP and the quorum system regulation of this process are shown. The potential of lactic acid bacteria and marine microorganisms as alternative surfactants producers (glycolipids, lipopeptides, phospholipids and fatty acids, glycolipopeptides are discussed. Their productivity and advantages over traditional producers are given as well. The properties of surfactants synthesized by lactic acid bacteria (the reduction of the surface tension, the critical micelle concentration, the stability in a wide range of pH, the temperature, the biological activity are summarized. Surfactants of nonpathogenic probiotic bacteria could be used as effective antimicrobial agents and antiadhesive and marine producers which able to synthesize unique metabolites that are not produced by other microorganisms.

  14. Surfactants at the Design Limit.

    Science.gov (United States)

    Czajka, Adam; Hazell, Gavin; Eastoe, Julian

    2015-08-04

    This article analyzes how the individual structural elements of surfactant molecules affect surface properties, in particular, the point of reference defined by the limiting surface tension at the aqueous cmc, γcmc. Particular emphasis is given to how the chemical nature and structure of the hydrophobic tails influence γcmc. By comparing the three different classes of surfactants, fluorocarbon, silicone, and hydrocarbon, a generalized surface packing index is introduced which is independent of the chemical nature of the surfactants. This parameter ϕcmc represents the volume fraction of surfactant chain fragments in a surface film at the aqueous cmc. It is shown that ϕcmc is a useful index for understanding the limiting surface tension of surfactants and can be useful for designing new superefficient surfactants.

  15. BINDING ISOTHERMS SURFACTANT-PROTEINS

    Directory of Open Access Journals (Sweden)

    Elena Irina Moater

    2011-12-01

    Full Text Available The interactions between surfactants and proteins shows some similarities with interactions between surfactants and polymers, but the hydrophobic amphoteric nature of proteins and their secondary and tertiary structure components make them different from conventional polymer systems. Many studies from the past about surfactant - proteins bonding used the dialysis techniques. Other techniques used to determine the binding isotherm, included ultrafiltration, ultracentrifugation, potentiometry, ion-selective electrode method and surface tension. High affinity isotherms which are typical of an anionic surfactant - protein bonding, exhibit an initial increase steep followed by a slow growth region and then a vertical growth above a certain concentration. This isotherm is typical of ionic surfactant to protein binding. Often the high affinity initial bond appears at very low concentrations of surfactant and therefore in some protein-surfactant systems, the exact shape of the isotherm in this region may be missing. The surfactant - protein binding is influenced by a number of variables such as the nature and chain length of surfactant, pH, ionic strength, temperature, nature of this protein and additives.

  16. LED-activated methylene blue-loaded Pluronic-nanogold hybrids for in vitro photodynamic therapy.

    Science.gov (United States)

    Simon, Timea; Boca-Farcau, Sanda; Gabudean, Ana-Maria; Baldeck, Patrice; Astilean, Simion

    2013-12-01

    In this work we introduce a new class of multifunctional photodynamic agents based on the coupling of photosensitizer molecules with noble metal nanoparticles, which can be efficiently activated under low light intensity. The favourable modification of the photophysical properties of methylene blue (MB) in MB-loaded Pluronic-nanogold hybrids (Au-PF127-MB) increases the probability of singlet oxygen generation, which in turn allows the use of a light emitting diode (LED) irradiation source instead of commonly used, more invasive lasers. In this regard, Au-PF127-MB treated human lung carcinoma cells (HTB 177) were irradiated at different light doses, using a 660 nm LED source, the results indicating a dose dependent therapeutic effect, decreasing the cell viability down to 13%. Owing to their effectiveness, biocompatibility and integrated imaging and therapeutic functionalities, Au-PF127-MB could represent an important development in the field of biophotonic applications.

  17. Correlating nanoscale structural changes to macromolecular gel formation in Laponite containing Pluronic F127 photogeling systems

    Science.gov (United States)

    Juggernauth, K. Anne; Love, Brian

    2012-02-01

    Polymer nanocomposites has been a growing scientific field over the last 20 years. Recently, there has been increasing interest on nanocomposite systems with active responses to external stimuli such as heat, magnetic fields and light. The focus of this work is on a reversible thermoresponsive system, Pluronic F127 with added inorganic disk-shaped nanoparticles of Laponite. We further modify this system with the addition of a photoacid generator to enable photogelation. However, the nanoscale particle-particle and polymer-particle interactions within this Laponite/ block copolymer system are not well understood. We report on the photogelation kinetics of this system and further probe the interactions and rearrangement kinetics with heat and light exposure using in-situ synchrotron small angle x-ray scattering.

  18. Preparation of curcumin-loaded pluronic F127/chitosan nanoparticles for cancer therapy

    Science.gov (United States)

    Phuc Le, Thi Minh; Phuc Pham, Van; Lua Dang, Thi Minh; Huyen La, Thi; Hanh Le, Thi; Huan Le, Quang

    2013-06-01

    Nanoparticles (NPs) have been proven to be an effective delivery system with few side effects for anticancer drugs. In this study, curcumin-loaded NPs have been prepared by an ionic gelation method using chitosan (Chi) and pluronic®F-127 (PF) as carriers to deliver curcumin to the target cancer cells. Prepared NPs were characterized using Zetasizer, fluorescence microscopy, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Our results showed that the encapsulation efficiency of curcumin was approximately 50%. The average size of curcumin-loaded PF/Chi NPs was 150.9 nm, while the zeta potential was 5.09 mV. Cellular uptake of curcumin-loaded NPs into HEK293 cells was confirmed by fluorescence microscopy.

  19. In situ coronary stent paving by Pluronic F127-alginate gel blends: Formulation and erosion tests.

    Science.gov (United States)

    Dalmoro, Annalisa; Barba, Anna Angela; Grassi, Mario; Grassi, Gabriele; Lamberti, Gaetano

    2016-07-01

    In this work the development of an experimental protocol to perform the in situ gel-paving of coronary stent is presented. Biocompatible aqueous blends of Pluronic F127 and sodium alginates are used as potential drug dosage system for pharmacological in situ treatment of coronary in-stent restenosis. Pluronic F127/alginate aqueous blend has the unique characteristic to be liquid at room condition and to form gel at physiological temperature. The proposed protocol is based on the blend injection on stent wall previously implanted in a flexible silicon pipe mimicking the coronary artery. Injected blend is warmed up until human body temperature achieving a soft gel, then it is reticulated by copper bivalent ions to obtain an hard gel. To test the gel paving resistance to erosion phenomena when it is exposed to fluid flux (i.e. blood flux) a dedicated device, (the Simulated Artery Device, SAD), was built to simulate the human circulatory apparatus. The SAD is an hydraulic circuit in which a buffer solution (at pH 7.4) was fluxed by a peristaltic pump through the pipe hosting the covered stent. Erosion tests were performed monitoring, by gravimetric and spectrophotometric methods, the residual mass anchored to stent mesh after given times. The obtained results showed that the in situ gel-paving developed protocol was efficacious and reliable. The gel-paving was completely eroded in a time of the same order of magnitude of the physiological period required to restore the coronary lesion (subsequent to the atheroma removal) and of a pharmacological therapy to inhibit the in-stent-restenosis pathology. © 2015 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 104B: 1013-1022, 2016.

  20. Pluronic F127 as a cell encapsulation material: utilization of membrane-stabilizing agents.

    Science.gov (United States)

    Khattak, Sarwat F; Bhatia, Surita R; Roberts, Susan C

    2005-01-01

    Thermoreversible gelation of the copolymer Pluronic F127 (generic name, poloxamer 407) in water makes it a unique candidate for cell encapsulation applications, either alone or to promote cell seeding and attachment in tissue scaffolds. At concentrations of 15-20% (w/w), aqueous Pluronic F127 (F127) solutions gel at physiological temperatures. The effect of F127 on viability and proliferation of human liver carcinoma cells (HepG2) was determined for both liquid and gel formulations. Cell concentration and viability over a 5-day period were measured by the trypan blue assay via hemocytometry and results were confirmed in both the MTT and LDH assays. With 0.1-5% (w/w) F127 (liquid), cells proliferated and maintained high viability over 5 days. However, at 10% (w/w) F127 (liquid), there was a significant decrease in cell viability and no cell proliferation was evident. HepG2 cell encapsulation in F127 concentrations ranging from 15 to 20% (w/w) (gel) resulted in complete cell death by 5 days. This was also true for the HMEC-1 (endothelial) and L6 (muscle) cell lines evaluated. Cell-seeding density did not affect cell survival or proliferation. Membrane-stabilizing agents (hydrocortisone, glucose, and glycerol) were added to the F127 gel formulations to improve cell viability. The steroid hydrocortisone demonstrated the most significant improvement in viability, from 70% (with 60 nM hydrocortisone added). These results suggest that F127 formulations supplemented with membrane-stabilizing agents can serve as viable cell encapsulation materials. In addition, hydrocortisone may be generally useful in the promotion of cell viability for a wide range of encapsulation materials.

  1. Optimization and evaluation of pluronic lecithin organogels as a transdermal delivery vehicle for sinomenine.

    Science.gov (United States)

    Ba, Wenqiang; Li, Zhou; Wang, Lisheng; Wang, Ding; Liao, Weiguo; Fan, Wentao; Wu, Yinai; Liao, Fengyun; Yu, Jianye

    2016-08-01

    The purpose of the present study was to prepare and optimize sinomenine (SIN) pluronic lecithin organogels system (PLO), and to evaluate the permeability of the optimized PLO in vitro and in vivo. Box-Behnken design was used to optimize the PLO and the optimized formulation was pluronic F127 of 19.61%, lecithin of 3.60% and SIN of 1.27%. The formulation was evaluated its skin permeation and drug deposition both in vitro and in vivo compared with gel. Permeation and deposition studies of PLO were carried out with Franz diffusion cells in vitro and with microdialysis in vivo. In vitro studies, permeation rate (Jss) of SIN from PLO was 146.55 ± 2.93 μg/cm(2)/h, significantly higher than that of gel (120.39 μg/cm(2)/h) and the amount of SIN deposited in skin from the PLO was 10.08 ± 0.86 μg/cm(2), significantly larger than that from gel (6.01 ± 0.04 μg/cm(2)). In vivo skin microdialysis studies showed that the maximum concentration (Cmax) of SIN from PLO in "permeation study" and "drug-deposition study" were 150.27 ± 20.85 μg/ml and 67.95 μg/ml, respectively, both significantly higher than that of SIN from gel (29.66 and 6.73 μg/ml). The results recommend that PLO can be used as an advantageous transdermal delivery vehicle to enhance the permeation and skin deposition of SIN.

  2. Surfactant Effects on the Morphology and Pseudocapacitive Behavior of V2 O5 ⋅H2 O.

    Science.gov (United States)

    Qian, Aniu; Zhuo, Kai; Shin, Myung Sik; Chun, Woo Won; Choi, Bit Na; Chung, Chan-Hwa

    2015-07-20

    To overcome the drawback of low electrical conductivity within supercapacitor applications, several surfactants are used for nanoscale V2 O5 to enhance the specific surface area. Polyethylene glycol 6000 (PEG-6000), sodium dodecylbenzene sulfonate (SDBS), and Pluronic P-123 (P123) controllers, if used as soft templates, easily form large specific surface area crystals. However, the specific mechanism through which this occurs and the influence of these surfactants is not clear for V2 O5 ⋅H2 O. In the present study, we aimed to investigate the mechanism of crystal growth through hydrothermal processes and the pseudocapacitive behavior of these crystals formed by using diverse surfactants, including PEG-6000, SDBS, and P123. Our results show that different surfactants can dramatically influence the morphology and capacitive behavior of V2 O5 ⋅H2 O powders. Linear nanowires, flower-like flakes, and curly bundled nanowires can be obtained because of electrostatic interactions in the presence of PEG-6000, SDBS, and P123, respectively. Furthermore, the electrochemical performance of these powders shows that the nanowires, which are electrodes mediated by PEG-6000, exhibit the highest capacitance of 349 F g(-1) at a scan rate of 5 mV s(-1) of all the surfactants studied. However, a symmetric P123 electrode comprising curly bundled nanowires with numerous nanopores showed an excellent and stable specific capacitance of 127 F g(-1) after 200 cycles. This work is beneficial to understanding the fundamental role of the surfactant in the assisted growth of V2 O5 ⋅H2 O and the resulting electrochemical properties of the pseudocapacitors, which could be useful for the future design of appropriate materials.

  3. Interaction of nonionic surfactant AEO9 with ionic surfactants

    Institute of Scientific and Technical Information of China (English)

    ZHANG Zhi-guo; YIN Hong

    2005-01-01

    The interaction in two mixtures of a nonionic surfactant AEO9 (C12H25O(CH2CH2O)9H) and different ionic surfactants was investigated. The two mixtures were AEO9/sodium dodecyl sulfate (SDS) and AEO9/cetyltrimethylammonium bromide (CTAB) at molar fraction of AEO9, αAEO9 =0.5. The surface properties of the surfactants, critical micelle concentration (CMC),effectiveness of surface tension reduction (γCMC), maximum surface excess concentration (Гmax) and minimum area per molecule at the air/solution interface (Amin) were determined for both individual surfactants and their mixtures. The significant deviations from ideal behavior (attractive interactions) of the nonionic/ionic surfactant mixtures were determined. Mixtures of both AEO9/SDS and AEO9/CTAB exhibited synergism in surface tension reduction efficiency and mixed micelle formation, but neither exhibited synergism in surface tension reduction effectiveness.

  4. ADSORPTION OF SURFACTANT ON CLAYS

    Science.gov (United States)

    Surfactants used to enhance remediation of soils by soil washing are often lost in the process. Neither the amount nor the cause of this loss is known. It is assumed that clays present in the soil are responsible for the loss of the surfactant. In this papere, adsorption prope...

  5. Surfactant monitoring by foam generation

    Science.gov (United States)

    Mullen, Ken I.

    1997-01-01

    A device for monitoring the presence or absence of active surfactant or other surface active agents in a solution or flowing stream based on the formation of foam or bubbles is presented. The device detects the formation of foam with a light beam or conductivity measurement. The height or density of the foam can be correlated to the concentration of the active surfactant present.

  6. Surfactant adsorption kinetics in microfluidics

    Science.gov (United States)

    Riechers, Birte; Maes, Florine; Akoury, Elias; Semin, Benoît; Gruner, Philipp; Baret, Jean-Christophe

    2016-10-01

    Emulsions are metastable dispersions. Their lifetimes are directly related to the dynamics of surfactants. We design a microfluidic method to measure the kinetics of adsorption of surfactants to the droplet interface, a key process involved in foaming, emulsification, and droplet coarsening. The method is based on the pH decay in the droplet as a direct measurement of the adsorption of a carboxylic acid surfactant to the interface. From the kinetic measurement of the bulk equilibration of the pH, we fully determine the adsorption process of the surfactant. The small droplet size and the convection during the droplet flow ensure that the transport of surfactant through the bulk is not limiting the kinetics of adsorption. To validate our measurements, we show that the adsorption process determines the timescale required to stabilize droplets against coalescence, and we show that the interface should be covered at more than 90% to prevent coalescence. We therefore quantitatively link the process of adsorption/desorption, the stabilization of emulsions, and the kinetics of solute partitioning—here through ion exchange—unraveling the timescales governing these processes. Our method can be further generalized to other surfactants, including nonionic surfactants, by making use of fluorophore-surfactant interactions.

  7. Antioxidant Microemulsion-based Ethylene Vinyl Acetate Film Containing Mangiferin and Surfactants

    Directory of Open Access Journals (Sweden)

    Boonnattakorn Rungkan

    2016-01-01

    Full Text Available Mangiferin, a natural antioxidant additive, was incorporated into an ethylene vinyl acetate copolymer (EVA containing 18% vinyl acetate (VA using the emulsion solvent evaporation technique. Sorbitan ester (Span®20 and polymeric surfactant (Pluronic®P−123 were compared. Mangiferin was finely dispersed in the suspension with the addition of surfactants studied. Span®20 was chosen as the surfactant for film preparation in the next step due to the dispersing and film forming properties. Effects of vinyl acetate (VA contents on the film properties were investigated. The EVA films with 12% VA had the highest tensile strength and oxygen barrier, followed by 18, 25 and 40% VA, respectively. Addition of Span®20 had only a slight effect on mechanical and barrier properties of the films, but markedly increased the release of mangiferin from the EVA matrices except in the 40% VA films. The maximum concentrations of mangiferin released from the 40, 25, 18 and 12% VA films into 95% ethanol were 83.30, 66.84, 51.77 and 34.57 μg·mL−11, respectively. The release concentrations from the 40 and 25% VA films was 2.4 and 1.9 folds of that from the 12% VA film, respectively. The antioxidant activity of the EVA films containing mangiferin and Span®20 was 80% radical-scavenging capacity (RSC for the 40 and 25% VA and 60% RSC for the 18 and 12% VA. The release of mangiferin from the EVA matrices may be controlled by appropriate selection of the surfactants and vinyl acetate contents.

  8. Role of pluronics on rheological, drying and crack initiation of 'suckable' gels of decontamination; Role des pluronics sur les proprietes rheologiques, de sechage et de fracturation des gels 'aspirables' de decontamination

    Energy Technology Data Exchange (ETDEWEB)

    Bousquet, C

    2007-12-15

    The aim of this work was to understand the role of an addition of pluronics on the rheological behaviour, the drying and the fracturing of 'suckable' gels used for nuclear decontamination. The system studied was an aqueous suspension of silica (100 g/L of Aerosil 380) in a strong acidic medium (HNO{sub 3}/H{sub 3}PO{sub 4} 1.5 mol/L/1.5 mol/L) in presence of pluronics. Pluronics are amphiphilic tri-blocks copolymers composed of ethylene poly-oxide blocks and of propylene poly-oxide. The first part of this study deals with the characterization of the rheological properties of the gels. From viscosity retaking measurements, flow rheo-grams analysis and the viscoelastic properties of the gels, have been determined an improvement of the rheological properties of the gels significant from the addition of 5 g/L of copolymer. In a second part, the determination of adsorption isotherms coupled to small angles neutrons diffusion measurements has revealed that copolymers are adsorbed flat on silica in bridging the aggregates between them and that the improvement of the rheological behaviour of the gels is due to the increase of the bonds density of the gelled lattice. Moreover, beyond 10 g/L, the adsorption saturation of copolymers at the surface of the silica prevents the bridging of the aggregates which induces the gel destabilization. The last part of this work deals with the characterization of characteristic values of drying and of crack initiation of gels. Then is revealed a relation between the drying kinetics and the formation of cracks in the gel layer. Moreover, the study of the evolution of stresses in the gel layer during time allows to reveal that the addition of pluronics to the formulation of gels allows to improve the gel resistance to the crack initiation and to the delamination. (O.M.)

  9. Innovation in surfactant therapy II: surfactant administration by aerosolization.

    Science.gov (United States)

    Pillow, J Jane; Minocchieri, S

    2012-01-01

    Instilled bolus surfactant is the only approved surfactant treatment for neonatal respiratory distress syndrome. However, recent trends towards increased utilization of noninvasive respiratory support for preterm infants with surfactant deficiency have created a demand for a similarly noninvasive means of administering exogenous surfactant. Past approaches to surfactant nebulization met with varying success due to inefficient aerosol devices resulting in low intrapulmonary delivery doses of surfactant with variable clinical effectiveness. The recent development of vibrating membrane nebulizers, coupled with appropriate positioning of the interface device, indicates that efficient delivery of aerosolized surfactant is now a realistic goal in infants. Evidence of clinical effect despite low total administered dose in pilot studies, together with suggestions of enhanced homogeneity of pulmonary distribution indicate that this therapy may be applied in a cost-effective manner, with minimal patient handling and disruption. These studies need to be subjected to appropriately designed randomized controlled trials. Further work is also required to determine the optimum delivery route (mask, intranasal prong, nasopharyngeal or laryngeal), dosing amount and redosing interval.

  10. Interaction of nonionic surfactant AEO9 with ionic surfactants*

    OpenAIRE

    2005-01-01

    The interaction in two mixtures of a nonionic surfactant AEO9 (C12H25O(CH2CH2O)9H) and different ionic surfactants was investigated. The two mixtures were AEO9/sodium dodecyl sulfate (SDS) and AEO9/cetyltrimethylammonium bromide (CTAB) at molar fraction of AEO9, α AEO9=0.5. The surface properties of the surfactants, critical micelle concentration (CMC), effectiveness of surface tension reduction (γ CMC), maximum surface excess concentration (Γ max) and minimum area per...

  11. Facile Synthesis of Gold-nanoparticles-decorated Polymer Assemblies and Core-Shell Gold Nanoparticles Using Pluronic Block Copolymers

    Institute of Scientific and Technical Information of China (English)

    SHOU Qing-hui; GUO Chen; GAO Hong-shuai; ZHOU Hua-cong; LIU Chun-zhao; LIU Hui-zhou

    2011-01-01

    Abstract:Synthesis of gold nanoparticles (AuNPs) and Pluronic triblock copolymer composite in aqueous medium was studied.Gold-polymer nanocomposite with different structures was fabricated by tailoring the molar ratio of gold precursors to Pluronic P123 molecules or pH value of the P123 solution.When a lower volume ratio of [AuCl4-]/[P123] (0.05) was employed at pH 11.1,a nanostructure similar to plum pudding was obtained.AuNPs with an average diameter of 13.1 nm were embedded in Pluronic assemblies,and each one held about 21 single gold nanoparticles.When [AuCl4-]/[P123] was increased to 0.1,core-shell structure was obtained if the pH value was in the range of 10.6~11.6,while gold polyhedra were fabricated when pH value was 8.1.Typical core-shell AuNPs had an average diameter of 9.6 nm with a narrow size distribution,while gold polyhedras with a mean diameter of 12.8 nm was obtained.The specific morphologies of the resultant nanocomposite were presumably obtained due to the synergistic interaction among the reactants.

  12. Pluronic lecithin organogel (PLO) of diltiazem hydrochloride: effect of solvents/penetration enhancers on ex vivo permeation.

    Science.gov (United States)

    Parhi, Rabinarayan; Suresh, Podilam; Pattnaik, Subasini

    2016-06-01

    In the present study, pluronic lecithin organogel (PLO) of diltiazem hydrochloride (DZH) was developed by taking different ratios of organic phase to aqueous phase (1:3, 1:4, and 1:5) with varying concentration of soya lecithin (20, 30, and 40 % w/w) in organic phase (isopropyl myristate, IPM) and pluronic (20, 25, and 30 % w/w) in aqueous phase, respectively, and characterized for in vitro parameters and ex vivo permeation study. The results of in vitro parameters were found to be within permissible limit and all the PLOs were physically stable at refrigeration and ambient temperature. The influence of phase ratio and different concentrations of soya lecithin on DZH release from the PLOs was found to be significant (p < 0.05), whereas the influences of different concentrations of pluronic were insignificant. The effect of different solvents/penetration enhancers viz. IPM, propylene glycol (PG), dimethyl sulphoxide (DMSO), and D-limonene, in combination and alone, on the permeation of DZH across the dorsal skin of rat was studied. Among all, formulation containing IPM (PLO6) exhibited highest flux of 147.317 μg/cm(2)/h. Furthermore, histopathology section of treated skin sample illustrated that lipid bilayer disruption was the mechanism for the DZH permeation. The above results indicated that PLO6 may serve as a promising alternative delivery system for DZH in the effective treatment of hypertension.

  13. Surfactant enhanced volumetric sweep efficiency

    Energy Technology Data Exchange (ETDEWEB)

    Harwell, J.H.; Scamehorn, J.F.

    1989-10-01

    Surfactant-enhanced waterflooding is a novel EOR method aimed to improve the volumetric sweep efficiencies in reservoirs. The technique depends upon the ability to induce phase changes in surfactant solutions by mixing with surfactants of opposite charge or with salts of appropriate type. One surfactant or salt solution is injected into the reservoir. It is followed later by injection of another surfactant or salt solution. The sequence of injections is arranged so that the two solutions do not mix until they are into the permeable regions well away from the well bore. When they mix at this point, by design they form a precipitate or gel-like coacervate phase, plugging this permeable region, forcing flow through less permeable regions of the reservoir, improving sweep efficiency. The selectivity of the plugging process is demonstrated by achieving permeability reductions in the high permeable regions of Berea sandstone cores. Strategies were set to obtain a better control over the plug placement and the stability of plugs. A numerical simulator has been developed to investigate the potential increases in oil production of model systems. Furthermore, the hardness tolerance of anionic surfactant solutions is shown to be enhanced by addition of monovalent electrolyte or nonionic surfactants. 34 refs., 32 figs., 8 tabs.

  14. MICROBIAL SURFACTANTS IN ENVIRONMENTAL TECHNOLOGIES

    Directory of Open Access Journals (Sweden)

    T. P. Pirog

    2015-08-01

    Full Text Available It was shown literature and own experimental data concerning the use of microbial surface active glycolipids (rhamno-, sophoro- and trehalose lipids and lipopeptides for water and soil purification from oil and other hydrocarbons, removing toxic heavy metals (Cu2+, Cd2+, Ni2+, Pb2+, degradation of complex pollution (oil and other hydrocarbons with heavy metals, and the role of microbial surfactants in phytoremediation processes. The factors that limit the use of microbial surfactants in environmental technologies are discussed. Thus, at certain concentrations biosurfactant can exhibit antimicrobial properties and inhibit microorganisms destructing xenobiotics. Microbial biodegradability of surfactants may also reduce the effectiveness of bioremediation. Development of effective technologies using microbial surfactants should include the following steps: monitoring of contaminated sites to determine the nature of pollution and analysis of the autochthonous microbiota; determining the mode of surfactant introduction (exogenous addition of stimulation of surfactant synthesis by autochthonous microbiota; establishing an optimal concentration of surfactant to prevent exhibition of antimicrobial properties and rapid biodegradation; research both in laboratory and field conditions.

  15. Electrokinetic investigation of surfactant adsorption.

    Science.gov (United States)

    Bellmann, C; Synytska, A; Caspari, A; Drechsler, A; Grundke, K

    2007-05-15

    Fuerstenau [D.W. Fuerstenau, in: M.L. Hair (Ed.), Dekker, New York, 1971, p. 143] has already discussed the role of hydrocarbon chain of surfactants, the effect of alkyl chain length, chain structure and the pH of the solution on the adsorption process of surfactants. Later Kosmulski [M. Kosmulski, Chemical Properties of Material Surfaces, Surfactant Science Series, vol. 102, Dekker, New York, Basel, 2001] included the effect of surfactant concentration, equilibration time, temperature and electrolyte in his approaches. Certainly, the character of the head groups of the surfactant and the properties of the adsorbent surface are the basis for the adsorption process. Different surfactants and adsorbents cause different adsorption mechanisms described firstly by Rosen [M.J. Rosen, Surfactants and Interfacial Phenomena, second ed., Wiley, New York, 1989]. These adsorption mechanisms and their influencing factors were studied by electrokinetic investigations. Here only changes of the charges at the surfaces could be detected. To control the results of electrokinetic investigations they were compared with results from ellipsometric measurements. In the case of surfactant adsorption the chain length was vitally important. It could be shown by the adsorption of alkyl trimethyl ammonium bromides onto polymer films spin coated at wafer surfaces. The influence of the chain length depending on surface properties of the polymer film was studied. Streaming potential measurements were applied for these investigations. The obtained results enabled us to calculate the molar cohesive free energy per mol of CH2-group in the alkaline chain of the surfactant if all other specific adsorption effects were neglected.

  16. Anaerobic Biodegradation of Detergent Surfactants

    Directory of Open Access Journals (Sweden)

    Erich Jelen

    2009-03-01

    Full Text Available Detergent surfactantscan be found in wastewater in relevant concentrations. Most of them are known as ready degradable under aerobic conditions, as required by European legislation. Far fewer surfactants have been tested so far for biodegradability under anaerobic conditions. The natural environment is predominantly aerobic, but there are some environmental compartments such as river sediments, sub-surface soil layer and anaerobic sludge digesters of wastewater treatment plants which have strictly anaerobic conditions. This review gives an overview on anaerobic biodegradation processes, the methods for testing anaerobic biodegradability, and the anaerobic biodegradability of different detergent surfactant types (anionic, nonionic, cationic, amphoteric surfactants.

  17. Simple control of surface topography of gold nanoshells by a surfactant-less seeded-growth method.

    Science.gov (United States)

    Topete, Antonio; Alatorre-Meda, Manuel; Villar-Álvarez, Eva M; Cambón, Adriana; Barbosa, Silvia; Taboada, Pablo; Mosquera, Víctor

    2014-07-23

    We report the synthesis of branched gold nanoshells (BGNS) through a seeded-growth surfactant-less method. This was achieved by decorating chitosan-Pluronic F127 stabilized poly(lactic-co-gycolic) acid nanoparticles (NPs) with Au seeds (NP-seed), using chitosan as an electrostatic self-assembling agent. Branched shells with different degrees of anisotropy and optical response were obtained by modulating the ratios of HAuCl4/K2CO3 growth solution, ascorbic acid (AA) and NP-seed precursor. Chitosan and AA were crucial in determining the BGNS size and structure, acting both as coreductants and structure directing growth agents. Preliminary cytotoxicity experiments point to the biocompatibility of the obtained BGNS, allowing their potential use in biomedical applications. In particular, these nanostructures with "hybrid" compositions, which combine the features of gold nanoshells and nanostars showed a better performance as surface enhanced Raman spectroscopy probes in detecting intracellular cell components than classical smoother nanoshells.

  18. Textural, structural and electrical properties of TiO2 nanoparticles using Brij 35 and P123 as surfactants

    Directory of Open Access Journals (Sweden)

    Dora Solís et al

    2008-01-01

    Full Text Available The effect of the use of the triblock copolymer Pluronic P123[(PEO20(PPO70(PEO20, Aldrich] and the non-ionic polyoxyethylene-lauryl ether Brij 35 as surfactants on the textural, structural and electrical properties of nanosized TiO2 is analyzed in this work. The as-obtained samples were thermally treated at 400 °C to eliminate the surfactant, promote dehydroxylation and crystallize the sample. The TiO2 samples were characterized by thermal analysis, N2 physisorption, x-ray diffraction analysis, micro-Raman spectroscopy and scanning electron microscopy. To evaluate the TiO2 electrical features, I–V data were obtained. The x-ray diffraction results show that in the chemical synthesis using surfactants, the crystallite size is smaller than that of the commercial sample. The Raman spectroscopy results clearly indicate that, when P123 is used, the anatase phase of TiO2 is obtained, whereas when Brij 35 is used a mixture of the anatase and brookite phases is obtained. The specific surface area and crystallite size of the TiO2 prepared as indicated above are higher and smaller, respectively, than the corresponding properties found in commercial TiO2. The I–V plot showed a nonlinear behavior of the nanosized TiO2. The samples obtained with P123 showed the best electrical conductivity.

  19. Phase diagram of the Pluronic L64-H2O micellar system from mechanical spectroscopy

    Science.gov (United States)

    Zhou, Xuemao; Wu, Xuebang; Wang, Huaguang; Liu, Changsong; Zhu, Zhengang

    2011-04-01

    The linear viscoelastic properties of aqueous Pluronic L64 solutions have been investigated at high copolymer concentrations (25-62 wt%) using our modified low-frequency mechanical spectroscopy. The concentration-temperature phase diagram of the L64/H2O system was constructed by studying the evolution of the loss modulus and loss tangent as temperature is increased at a fixed frequency. A particular attention was focused on the dynamics approaching the beginning and ending points (39% and 60%) of the fusiform gel region in the phase diagram. The dynamics is found to have a similar viscoelastic behavior at the low and high concentrations, where a frequency scaling expected for a static percolated network is exhibited. Moreover, with increasing temperature, the system above the critical gel concentration undergoes a transition from a viscoelastic liquid to a solid gel through a percolated particle network. Therefore, our results suggest that the formation of the gel is dominated by the percolation of the particle clusters.

  20. Thermogelling aqueous fluids containing low concentrations of Pluronic F127 and laponite nanoparticles.

    Science.gov (United States)

    Sun, Kunshan; Raghavan, Srinivasa R

    2010-06-01

    The triblock copolymer Pluronic F127 (PF127) is frequently used in colloidal and pharmaceutical formulations. Concentrated aqueous solutions of PF127 (>15 wt %) are known to undergo thermogelling (i.e., a sol-to-gel transition upon heating), which is attributed to the formation of a volume-filling cubic array of micelles. Here, we report that thermogelling can occur at much lower PF127 concentrations (1.2 to 8 wt %) if nanoparticles of laponite (25-nm-diameter disks) are also present in the formulation. Thermogelling in laponite/PF127 mixtures requires each component to be present above a minimum level. The gels have moduli around 100 Pa, and they can be reversibly liquefied to sols upon cooling. Rheological techniques, small-angle neutron scattering (SANS), and transmission electron microscopy (TEM) are used to characterize the thermogels. We attribute the onset of thermogelling to depletion flocculation of the laponite particles into a network by spherical micelles of PF127.

  1. In vivo triarylmethyl radical stabilization through encapsulation in Pluronic F-127 hydrogel.

    Science.gov (United States)

    Abbas, Kahina; Boutier-Pischon, Audrey; Auger, Florian; Françon, Dominique; Almario, Antonio; Frapart, Yves-Michel

    2016-09-01

    In vivo electron paramagnetic resonance (EPR) imaging and spectroscopy are non-invasive technologies used to specifically detect and quantify paramagnetic species. However, the relative instability of spin probes such as triarylmethyl radicals limits their application to conduct oxygen quantification and mapping. In this study we encapsulated tetrathiatriarylmethyl radical (TAM; known as "Finland" probe) in Pluronic F-127 hydrogel (PF-127) in order to limit its degradation and evaluate its in vitro and in vivo EPR properties as a function of oxygen. Our results show that the EPR signal of encapsulated TAM in PF-127 hydrogel is similar to the one in solution. Although it is less sensitive to oxygen, it is suitable for oximetry. We also demonstrated that the incorporation of TAM in PF-127 hydrogel leads to an improved in vivo EPR stability of the radical under anesthesia. This new formulation enables high quality EPR imaging and oximetry and paves the way for the application of TAM radical-based probes in various biomedical fields.

  2. Morphological and Rheological Characterization of Gold Nanoparticles Synthesized Using Pluronic P103 as Soft Template

    Directory of Open Access Journals (Sweden)

    Nancy Tepale

    2016-01-01

    Full Text Available The synthesis of gold nanoparticles (Au-NPs, using Pluronic® P103 as soft template to design tuned hybrid gold/P103 nanomaterials, is reported here. The effect of the concentration of P103 and the synthesis temperature on the growth, size, and morphology of Au-NPs were studied. The rheological properties of these hybrid nanomaterials at different measured temperatures were studied as well. By increasing the concentration of P103, the micelles progressively grew due to an increase in the number of surface cavities. These cavities came together causing large nucleation centers and developing larger Au-NPs. The synthesis temperature was varied to induce significant dehydration of the P103 micelles. Below the cloud point temperature micelles underwent distinct changes related to spherical-to-polymer-like micelles transitions. Two nanostructures were formed: (1 small Au-NPs arranged on the surface of micelles, which acted as soft templates, and (2 large and independent Au-NPs. Above the cloud point temperature, Au-NPs were related to the shape and size of the P103 micellar aggregates. Rheological measurements showed that viscosity was sensitive to the concentration of P103. Also, it was demonstrated that synthesis temperature had a considerable influence on viscosity of the produced nanomaterials.

  3. In vivo triarylmethyl radical stabilization through encapsulation in Pluronic F-127 hydrogel

    Science.gov (United States)

    Abbas, Kahina; Boutier-Pischon, Audrey; Auger, Florian; Françon, Dominique; Almario, Antonio; Frapart, Yves-Michel

    2016-09-01

    In vivo electron paramagnetic resonance (EPR) imaging and spectroscopy are non-invasive technologies used to specifically detect and quantify paramagnetic species. However, the relative instability of spin probes such as triarylmethyl radicals limits their application to conduct oxygen quantification and mapping. In this study we encapsulated tetrathiatriarylmethyl radical (TAM; known as "Finland" probe) in Pluronic F-127 hydrogel (PF-127) in order to limit its degradation and evaluate its in vitro and in vivo EPR properties as a function of oxygen. Our results show that the EPR signal of encapsulated TAM in PF-127 hydrogel is similar to the one in solution. Although it is less sensitive to oxygen, it is suitable for oximetry. We also demonstrated that the incorporation of TAM in PF-127 hydrogel leads to an improved in vivo EPR stability of the radical under anesthesia. This new formulation enables high quality EPR imaging and oximetry and paves the way for the application of TAM radical-based probes in various biomedical fields.

  4. Pluronic F127 nanomicelles engineered with nuclear localized functionality for targeted drug delivery.

    Science.gov (United States)

    Li, Yong-Yong; Li, Lan; Dong, Hai-Qing; Cai, Xiao-Jun; Ren, Tian-Bin

    2013-07-01

    PKKKRKV (Pro-Lys-Lys-Lys-Arg-Lys-Val, PV7), a seven amino acid peptide, has emerged as one of the primary nuclear localization signals that can be targeted into cell nucleus via the nuclear import machinery. Taking advantage of chemical diversity and biological activities of this short peptide sequence, in this study, Pluronic F127 nanomicelles engineered with nuclear localized functionality were successfully developed for intracellular drug delivery. These nanomicelles with the size ~100 nm were self-assembled from F127 polymer that was flanked with two PV7 sequences at its both terminal ends. Hydrophobic anticancer drug doxorubicin (DOX) with inherent fluorescence was chosen as the model drug, which was found to be efficiently encapsulated into nanomicelles with the encapsulation efficiency at 72.68%. In comparison with the non-functionalized namomicelles, the microscopic observation reveals that PV7 functionalized nanomicelles display a higher cellular uptake, especially into the nucleus of HepG2 cells, due to the nuclear localization signal effects. Both cytotoxicity and apoptosis studies show that the DOX-loaded nanomicelles were more potent than drug nanomicelles without nuclear targeting functionality. It was thus concluded that PV7 functionalized nanomicelles could be a potentially alternative vehicle for nuclear targeting drug delivery.

  5. Peripheral nerve regeneration within an asymmetrically porous PLGA/Pluronic F127 nerve guide conduit.

    Science.gov (United States)

    Oh, Se Heang; Kim, Jun Ho; Song, Kyu Sang; Jeon, Byeong Hwa; Yoon, Jin Hwan; Seo, Tae Beom; Namgung, Uk; Lee, Il Woo; Lee, Jin Ho

    2008-04-01

    Asymmetrically porous tubes with selective permeability and hydrophilicity as nerve guide conduits (NGCs) were fabricated using poly(lactic-co-glycolic acid) (PLGA) and Pluronic F127 by a modified immersion precipitation method. The inner surface of the tube had nano-size pores ( approximately 50nm) which can effectively prevent from fibrous tissue infiltration but permeate nutrients and retain neurotrophic factors, while the outer surface had micro-size pores ( approximately 50microm) which can allow vascular ingrowth for effective supply of nutrients into the tube. From the animal study using a rat model, the hydrophilized PLGA/F127 (3wt%) tube showed better nerve regeneration behavior than the control silicone or hydrophobic PLGA tubes, as investigated by immunohistochemical observation (by fluorescent microscopy with anti-neurofilament staining), histological observations (by light microscopy with toluidine blue staining and transmission electron microscopy), and electrophysiological evaluation (by compound muscle action potential measurement). This is probably owing to the effective permeation of nutrients and prevention of fibrous scar tissue invasion as well as the good mechanical strength of the tube to maintain a stable support structure for the nerve regeneration.

  6. Treatment with exogenous surfactant stimulates endogenous surfactant synthesis in premature infants with respiratory distress syndrome

    NARCIS (Netherlands)

    Bunt, JEH; Carnielli, VP; Janssen, DJ; Wattimena, JLD; Hop, WC; Sauer, PJ; Zimmermann, LJI

    2000-01-01

    Objective: Treatment of preterm infants with respiratory distress syndrome (RDS) with exogenous surfactant has greatly improved clinical outcome. Some infants require multiple doses, and it has not been studied whether these large amounts of exogenous surfactant disturb endogenous surfactant metabol

  7. Electrochemical Oscillations Induced by Surfactants

    Institute of Scientific and Technical Information of China (English)

    翟俊红; 贺占博

    2003-01-01

    A new type of electrochemical oscillation induced by surfactant was observed in experiments. The electrochemical system is a Daniell cell with a copper rod in CuSO4 aqueous and an aluminum rod in Al(NO3)3 aqueous as electrodes. The surfactants are CTAB, TX-100, SLS. The addition of trace surfactant solution by a micro-syringe made the original monotonously changing electrochemical system produce obvious periodic phenomena. At the mean time, the copper ion selective electrode and Hg2SO4 reference electrode were used to monitor the copper electrode reaction and determine its rate constant k of first order reaction. According to the experimental results of electrode reaction kinetics, the possible mechanism was found to be the polarization induced from the directional adsorption of trace surfactant on the electrode surface. That is the electrochemical oscillations.

  8. Persurf, a New Method to Improve Surfactant Delivery: A Study in Surfactant Depleted Rats

    OpenAIRE

    2012-01-01

    PURPOSE: Exogenous surfactant is not very effective in adults with ARDS, since surfactant does not reach atelectatic alveoli. Perfluorocarbons (PFC) can recruit atelectatic areas but do not replace impaired endogenous surfactant. A surfactant-PFC-mixture could combine benefits of both therapies. The aim of the proof-of-principal-study was to produce a PFC-in-surfactant emulsion (Persurf) and to test in surfactant depleted Wistar rats whether Persurf achieves I.) a more homogenous pulmonary di...

  9. 兔牙髓干细胞与Pluronic F-127嵌段共聚物的体外相容性%Biocompatibility of dental pulp progenitor cells and Pluronic F-127 hydrogel

    Institute of Scientific and Technical Information of China (English)

    帕尔哈提·阿布肚热合曼; 白尔娜·吾守尔; 木合塔尔·霍加; 刘晓文

    2016-01-01

    目的:探讨牙髓干细胞(DPSC)与Pluronic F⁃127水凝胶生物相容性。方法酶解组织块法获得DPSC,镜下观察细胞形态。制备20%、25%、30%(w/v)的Pluronic F⁃127水凝胶,扫描电镜(SEM)观察水凝胶支架空间形态,检测支架材料的溶胀率,凝胶化时间。用不同浓度Pluronic F⁃127水凝胶包封DPSC进行三维培养,并以普通培养皿的二维培养作为对照,镜下观察细胞生长情况。培养第1、3、5、7天通过噻唑蓝(MTT)法检测支架对DPSC增殖的影响。将最佳浓度的Pluronic F⁃127用于包封DPSC,常规矿化液诱导14 d进行茜素红、甲苯胺蓝染色、实时荧光定量聚合酶链反应(PCR)检测成骨相关骨桥蛋白(OPN)、Ⅱ型胶原,以评价Pluronic F⁃127对DPSC成骨及成软骨分化的影响。数据分析采用单因素方差分析。结果成功分离并纯化DPSC,细胞在支架内生长良好;MTT结果显示:第1天各组间差异无统计学意义;第3天,20%Pluronic F⁃127组细胞增殖A标准值(0.774±0.095)显著高于其他培养组(A对照=0.353±0.096、A25%PF=0.559±0.053、A30%PF=0.532±0.093),差异有统计学意义(F=15.993,P=0.000);第5天时,20%Pluronic F⁃127组细胞增殖A标准值(0.554±0.510)显著高于其他培养组(A对照=0.260±0.097、A25%PF=0.353±0.049、A30%PF=0.212±0.049),差异有统计学意义(F=20.821,P=0.000)。成骨及成软骨诱导后茜素红及甲苯胺蓝染色呈阳性,对照组呈阴性。实时荧光定量PCR显示,三维诱导组mRNA相对表达水平显著高于其他培养组,差异有统计学意义(FOPN=65.576,POPN=0.000;FCOL⁃2=38.382,PCOL⁃2=0.000)。结论20%Pluronic F⁃127适合DPSC的培养,并可支持其生长及分化。Pluronic F⁃127可作为DPSC的生物载体,有望成为理想的组织工程支架材料。%Objective To assess the biocompatibility of nonionic triblock copolymer

  10. Biomimicry of surfactant protein C.

    Science.gov (United States)

    Brown, Nathan J; Johansson, Jan; Barron, Annelise E

    2008-10-01

    Since the widespread use of exogenous lung surfactant to treat neonatal respiratory distress syndrome, premature infant survival and respiratory morbidity have dramatically improved. Despite the effectiveness of the animal-derived surfactant preparations, there still remain some concerns and difficulties associated with their use. This has prompted investigation into the creation of synthetic surfactant preparations. However, to date, no clinically used synthetic formulation is as effective as the natural material. This is largely because the previous synthetic formulations lacked analogues of the hydrophobic proteins of the lung surfactant system, SP-B and SP-C, which are critical functional constituents. As a result, recent investigation has turned toward the development of a new generation of synthetic, biomimetic surfactants that contain synthetic phospholipids along with a mimic of the hydrophobic protein portion of lung surfactant. In this Account, we detail our efforts in creating accurate mimics of SP-C for use in a synthetic surfactant replacement therapy. Despite SP-C's seemingly simple structure, the predominantly helical protein is extraordinarily challenging to work with given its extreme hydrophobicity and structural instability, which greatly complicates the creation of an effective SP-C analogue. Drawing inspiration from Nature, two promising biomimetic approaches have led to the creation of rationally designed biopolymers that recapitulate many of SP-C's molecular features. The first approach utilizes detailed SP-C structure-activity relationships and amino acid folding propensities to create a peptide-based analogue, SP-C33. In SP-C33, the problematic and metastable polyvaline helix is replaced with a structurally stable polyleucine helix and includes a well-placed positive charge to prevent aggregation. SP-C33 is structurally stable and eliminates the association propensity of the native protein. The second approach follows the same design

  11. Synergetic effect of benzotriazole and non-ionic surfactant on copper chemical mechanical polishing in KIO{sub 4}-based slurries

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, Liang [State Key Laboratory of Tribology, Tsinghua University, Beijing 100084 (China); Center for Advanced Materials Processing, Clarkson University, Potsdam, NY 13699 (United States); He, Yongyong [State Key Laboratory of Tribology, Tsinghua University, Beijing 100084 (China); Niu, Xiangyu; Li, Yuzhuo [Center for Advanced Materials Processing, Clarkson University, Potsdam, NY 13699 (United States); Luo, Jianbin, E-mail: luojb@tsinghua.edu.cn [State Key Laboratory of Tribology, Tsinghua University, Beijing 100084 (China)

    2014-05-02

    Ruthenium will be integrated into copper interconnects as a barrier layer in the near future. During the chemical mechanical polishing process of the ruthenium barrier layer, copper polishing performance with barrier slurries is crucial to microchips' final performance. This paper mainly studies the synergetic effect of benzotriazole (BTA) and non-ionic surfactant on copper polishing performance using KIO{sub 4}-based barrier slurries. The results show that, the copper removal rate (RR) and static etching rate increase with increasing concentration of KIO{sub 4} due to the increasing proportion of the Cu–periodate and Cu–iodate compounds like Cu(IO{sub 4}){sub 2} and Cu(IO{sub 3}){sub 2} of the passivating film on the copper surface; the added BTA can further enhance the copper RR instead of suppressing it probably due to the formation of incomplete Cu–BTA thin film. It is demonstrated that the combination of BTA and non-ionic surfactant exhibits excellent performance in suppressing the copper RR to about 200 Å/min, realizing satisfactory copper surface quality and achieving desirable material removal rate selectivity among copper, ruthenium and low-κ dielectrics. The synergetic passivation mechanism of BTA and non-ionic surfactant on the copper surface was investigated. It is proposed that in the presence of KIO{sub 4} as an oxidizer, the added BTA and non-ionic surfactant can form a porous passivating film on the copper surface which is mainly composed of the Cu–BTA complex, the adsorbed non-ionic surfactant and the leftover insoluble copper compounds like Cu(IO{sub 4}){sub 2} and Cu(IO{sub 3}){sub 2}, and then the hydrophobic polypropylene oxide segments of non-ionic surfactant can be effectively absorbed on the hydrophobic Cu–BTA complex as a supplement. The above two parts are integrated into a complete passivating film to protect the copper surface from chemical dissolution and excessive mechanical abrasion. - Highlights: • The copper

  12. Surfactant for pediatric acute lung injury.

    Science.gov (United States)

    Willson, Douglas F; Chess, Patricia R; Notter, Robert H

    2008-06-01

    This article reviews exogenous surfactant therapy and its use in mitigating acute lung injury (ALI) and the acute respiratory distress syndrome (ARDS) in infants, children, and adults. Biophysical and animal research documenting surfactant dysfunction in ALI/ARDS is described, and the scientific rationale for treatment with exogenous surfactant is discussed. Major emphasis is placed on reviewing clinical studies of surfactant therapy in pediatric and adult patients who have ALI/ARDS. Particular advantages from surfactant therapy in direct pulmonary forms of these syndromes are described. Also discussed are additional factors affecting the efficacy of exogenous surfactants in ALI/ARDS.

  13. Self-hardening and thermoresponsive alpha tricalcium phosphate/pluronic pastes.

    Science.gov (United States)

    Maazouz, Yassine; Montufar, Edgar B; Malbert, Julien; Espanol, Montserrat; Ginebra, Maria-Pau

    2017-02-01

    Although calcium phosphate cements (CPCs) are used for bone regeneration in a wide range of clinical applications, various physicochemical phenomena are known to hinder their potential use in minimally invasive surgery or in highly vascularized surgical sites, mainly because of their lack of injectability or their low washout resistance. The present work shows that the combination of CPCs with an inverse-thermoresponsive hydrogel is a good strategy for finely tuning the cohesive and rheological properties of CPCs to achieve clinical acceptable injectability to prevent phase separation during implantation and cohesion to avoid washout of the paste. The thermoresponsive CPC developed combines alpha-tricalcium phosphate with an aqueous solution of pluronic F127, which exhibits an inverse thermoresponsive behaviour, with a gelling transformation at around body temperature. These novel CPCs exhibited temperature-dependent properties. Addition of the polymer enhanced the injectability of the paste, even at a low liquid-to-powder ratio, and allowed the rheological properties of the cement to be tuned, with the injection force decreasing with the temperature of the paste. Moreover, the cohesion of the paste was also temperature-dependent and increased as the temperature of the host medium increased due to gelling induced in the paste. The thermoresponsive cement exhibited excellent cohesion and clinically acceptable setting times at 37°C, irrespective of the initial temperature of the paste. The addition of pluronic F127 slightly delayed the setting reaction in the early stages but did not hinder the full transformation to calcium-deficient hydroxyapatite. Moreover, the frozen storage of premixed thermoresponsive cement pastes was explored, the main physicochemical properties of the cements being maintained upon thawing, even after 18months of frozen storage. This avoids the need to mix the cement in the operating theatre and allows its use off-the-shelf. The reverse

  14. Engineering of a Pluronic F127 functionalized magnetite/graphene nanohybrid for chemophototherapy.

    Science.gov (United States)

    Li, Yongyong; Liu, Jiaqiang; Dong, Haiqing; Liu, Guangzhen; Hu, Haiqing

    2014-02-14

    In this study, a multifunctional graphene based nanohybrid, termed as GN/Fe3O4/PF127, is engineered via a facile one-pot process consisting of simultaneous reduction of graphene oxide/Fe3O4 and subsequent assembly of Pluronic F127 (PF127) onto graphene nanosheets (GNs). The unique aromatic and planar structure of GNs allows the attachment of multiple functional components including MRI contrast agent (Fe3O4 nanoparticles) and an aromatic anticancer drug like doxorubicin (DOX), as well as PF127 coating which imparts physiological dispersivity and stability to the nanohybrid. The successful assembly process is revealed by TEM observation, size and FITR monitoring. In contrast with the primitive graphene or its oxide derivative, the resulting GN/Fe3O4/PF127 nanohybrids have shown high biological dispersion and MRI effect for diagnosis due to the incorporation of superparamagnetic Fe3O4 nanoparticles without evident cytotoxicity. Moreover, the GN/Fe3O4/PF127 nanohybrid exhibits a photothermal effect due to the considerable optical absorption in the near-infrared region of GNs. The GN/Fe3O4/PF127 nanohybrid could be a further platform for chemophototherapy assisted by the therapeutic DOX. Cellular toxicity assays indicated that the DOX-loaded GN/Fe3O4/PF127 nanohybrid showed a remarkable cytotoxicity to HeLa cells and the cytotoxic effect was intensified when subjected to photoirradiation. Confocal laser scanning microscopy (CLSM) and flow cytometric analysis (FCAS) revealed that the nanohybrid could be easily uptaken into HeLa cells.

  15. Pluronic F127 nanomicelles engineered with nuclear localized functionality for targeted drug delivery

    Energy Technology Data Exchange (ETDEWEB)

    Li, Yong-Yong; Li, Lan; Dong, Hai-Qing, E-mail: inano_donghq@tongji.edu.cn; Cai, Xiao-Jun; Ren, Tian-Bin, E-mail: rentianbin@yeah.net

    2013-07-01

    PKKKRKV (Pro-Lys-Lys-Lys-Arg-Lys-Val, PV7), a seven amino acid peptide, has emerged as one of the primary nuclear localization signals that can be targeted into cell nucleus via the nuclear import machinery. Taking advantage of chemical diversity and biological activities of this short peptide sequence, in this study, Pluronic F127 nanomicelles engineered with nuclear localized functionality were successfully developed for intracellular drug delivery. These nanomicelles with the size ∼ 100 nm were self-assembled from F127 polymer that was flanked with two PV7 sequences at its both terminal ends. Hydrophobic anticancer drug doxorubicin (DOX) with inherent fluorescence was chosen as the model drug, which was found to be efficiently encapsulated into nanomicelles with the encapsulation efficiency at 72.68%. In comparison with the non-functionalized namomicelles, the microscopic observation reveals that PV7 functionalized nanomicelles display a higher cellular uptake, especially into the nucleus of HepG2 cells, due to the nuclear localization signal effects. Both cytotoxicity and apoptosis studies show that the DOX-loaded nanomicelles were more potent than drug nanomicelles without nuclear targeting functionality. It was thus concluded that PV7 functionalized nanomicelles could be a potentially alternative vehicle for nuclear targeting drug delivery. - Highlights: ► A new nuclear targeted drug delivery system based on micelles is developed. ► This micellar system features a core-shell structure with the size peaked at 100 nm. ► PV7, a short peptide sequence, is adopted as a nuclear targeting ligand. ► PV7 functionalized drug loaded micelles are more potent in killing tumor cells.

  16. Pluronic-based micelle encapsulation potentiates myricetin-induced cytotoxicity in human glioblastoma cells.

    Science.gov (United States)

    Tang, Xiang-Jun; Huang, Kuan-Ming; Gui, Hui; Wang, Jun-Jie; Lu, Jun-Ti; Dai, Long-Jun; Zhang, Li; Wang, Gang

    As one of the natural herbal flavonoids, myricetin has attracted much research interest, mainly owing to its remarkable anticancer properties and negligible side effects. It holds great potential to be developed as an ideal anticancer drug through improving its bioavailability. This study was performed to investigate the effects of Pluronic-based micelle encapsulation on myricetin-induced cytotoxicity and the mechanisms underlying its anticancer properties in human glioblastoma cells. Cell viability was assessed using a methylthiazol tetrazolium assay and a real-time cell analyzer. Immunoblotting and quantitative reverse transcriptase polymerase chain reaction techniques were used for determining the expression levels of related molecules in protein and mRNA. The results indicated that myricetin-induced cytotoxicity was highly potentiated by the encapsulation of myricetin. Mitochondrial apoptotic pathway was demonstrated to be involved in myricetin-induced glioblastoma cell death. The epidermal growth factor receptor (EGFR)/PI3K/Akt pathway located in the plasma membrane and cytosol and the RAS-ERK pathway located in mitochondria served as upstream and downstream targets, respectively, in myricetin-induced apoptosis. MiR-21 inhibitors interrupted the expression of EGFR, p-Akt, and K-Ras in the same fashion as myricetin-loaded mixed micelles (MYR-MCs) and miR-21 expression were dose-dependently inhibited by MYR-MCs, indicating the interaction of miR-21 with MYR-MCs. This study provided evidence supportive of further development of MYR-MC formulation for preferentially targeting mitochondria of glioblastoma cells.

  17. Dual-degradable disulfide-containing PEI–Pluronic/DNA polyplexes: transfection efficiency and balancing protection and DNA release

    Directory of Open Access Journals (Sweden)

    Zhang L

    2013-09-01

    Full Text Available Lifen Zhang,* Zhenzhen Chen,* Yanfeng LiState Key Laboratory of Applied Organic Chemistry, Key Laboratory of Nonferrous Metals Chemistry and Resources Utilization of Gansu Province, College of Chemistry and Chemical Engineering, Institute of Biochemical Engineering and Environmental Technology, Lanzhou University, Lanzhou, People's Republic of China*These authors contributed equally to this workAbstract: Polymeric gene-delivery vectors to achieve lack of toxicity and a balance between protection and DNA release remains a formidable challenge. Incorporating intracellular environment-responsive degradable bonds is an appreciable step toward developing safer transfection agents. In this study, novel, dual-degradable polycation copolymers (Pluronic-diacrylate [PA]–polyethyleneimine [PEI]–SS were synthesized through the addition of low molecular weight (800 Da PEI cross-linked with SS (PEI-SS to PA. Three PA-PEI-SS copolymers (PA-PEI-SS1, 2, and 3 with different PEI-SS to Pluronic molar ratios were investigated and found to strongly condense plasmid DNA into positively charged nanoparticles with an average particle size of approximately 200 nm and to possess higher stability against DNase I digestion and sodium heparin. Disulfide and ester bonds of the copolymers were susceptible to intracellular redox conditions. In vitro experiments demonstrated that the PA-PEI-SS copolymers had significantly lower cytotoxicity and higher transfection efficiency in both BGC-823 and 293T cell lines than the controls of degradable PEI-SS and nondegradable 25 kDa PEI. Transfection activity was influenced by the PEI-SS content in the polymers and PA-PEI-SS1 showed the highest efficiency of the three copolymers. These studies suggest that these dual-degradable copolymers could be used as potential biocompatible gene delivery carriers.Keywords: Pluronic, PEI, gene vector, dual-degradable, disulfide-containing linker

  18. Effect of doxorubicin/pluronic SP1049C on tumorigenicity, aggressiveness, DNA methylation and stem cell markers in murine leukemia.

    Directory of Open Access Journals (Sweden)

    Daria Y Alakhova

    Full Text Available PURPOSE: Pluronic block copolymers are potent sensitizers of multidrug resistant cancers. SP1049C, a Pluronic-based micellar formulation of doxorubicin (Dox has completed Phase II clinical trial and demonstrated safety and efficacy in patients with advanced adenocarcinoma of the esophagus and gastroesophageal junction. This study elucidates the ability of SP1049C to deplete cancer stem cells (CSC and decrease tumorigenicity of cancer cells in vivo. EXPERIMENTAL DESIGN: P388 murine leukemia ascitic tumor was grown in BDF1 mice. The animals were treated with: (a saline, (b Pluronics alone, (c Dox or (d SP1049C. The ascitic cancer cells were isolated at different passages and examined for 1 in vitro colony formation potential, 2 in vivo tumorigenicity and aggressiveness, 3 development of drug resistance and Wnt signaling activation 4 global DNA methylation profiles, and 5 expression of CSC markers. RESULTS: SP1049C treatment reduced tumor aggressiveness, in vivo tumor formation frequency and in vitro clonogenic potential of the ascitic cells compared to drug, saline and polymer controls. SP1049C also prevented overexpression of BCRP and activation of Wnt-β-catenin signaling observed with Dox alone. Moreover, SP1049C significantly altered the DNA methylation profiles of the cells. Finally, SP1049C decreased CD133(+ P388 cells populations, which displayed CSC-like properties and were more tumorigenic compared to CD133(- cells. CONCLUSIONS: SP1049C therapy effectively suppresses the tumorigenicity and aggressiveness of P388 cells in a mouse model. This may be due to enhanced activity of SP1049C against CSC and/or altered epigenetic regulation restricting appearance of malignant cancer cell phenotype.

  19. Dynamics of surfactant sorption at the air/water interface: continuous-flow tensiometry.

    Science.gov (United States)

    Svitova, T F; Wetherbee, M J; Radke, C J

    2003-05-01

    Dynamic interfacial tensiometry, gauged by axisymmetric drop shape analysis of static drops or bubbles, provides useful information on surfactant adsorption kinetics. However, the traditional pendant-drop methodology is not readily amenable to the study of desorption kinetics. Thus, the question of sorption reversibility is difficult to assess by this technique. We extend classical pendant/sessile drop dynamic tensiometry by immersing a sessile bubble in a continuously mixed optical cell. Ideal-mixed conditions are established by stirring and by constant flow through the cell. Aqueous surface-active-agent solutions are either supplied to the cell (loading) or removed from the cell by flushing with water (washout), thereby allowing study of both adsorption and desorption kinetics. Well-mixed conditions and elimination of any mass transfer resistance permit direct identification of sorption kinetic barriers to and from the external aqueous phase with time constants longer than the optical-cell residence time. The monodisperse nonionic surfactant ethoxy dodecyl alcohol (C(12)E(5)), along with cationic cetyltrimethyl ammonium bromide (CTAB) in the presence of added salt, adsorbs and desorbs instantaneously at the air/water interface. In these cases, the experimentally observed dynamic-tension curves follow the local-equilibrium model precisely for both loading and washout. Accordingly, these surfactants below their critical micelle concentrations (CMC) exhibit no detectable sorption-activation barriers on time scales of order a min. However, the sorption dynamics of dilute CTAB in the absence of electrolyte is markedly different from that in the presence of KBr. Here CTAB desorption occurs at local equilibrium, but the adsorption rate is kinetically limited, most likely due to an electrostatic barrier arising as the charged surfactant accumulates at the interface. The commercial, polydisperse nonionic surfactant ethoxy nonylphenol (NP9) loads in good agreement with

  20. Surfactant recovery from water using foam fractionation

    Energy Technology Data Exchange (ETDEWEB)

    Tharapiwattananon, N.; Osuwan, S. [Chulalongkorn Univ., Bangkok (Thailand); Scamehorn, J.F. [Inst. of Oklahoma, Norman, OK (United States)] [and others

    1996-05-01

    The purpose of this study was to investigate the use of foam fractionation to recover surfactant from water. A simple continuous mode foam fractionation was used and three surfactants were studied (two anionic and one cationic). The effects of air flow rate, foam height, liquid height, liquid feed surfactant concentration, and sparger porosity were studied. This technique was shown to be effective in either surfactant recovery or the reduction of surfactant concentration in water to acceptable levels. As an example of the effectiveness of this technique, the cetylpyridinium chloride concentration in water can be reduced by 90% in one stage with a liquid residence time of 375 minutes. The surfactant concentration in the collapsed foam is 21.5 times the feed concentration. This cationic surfactant was easier to remove from water by foam fractionation than the anionic surfactants studied.

  1. Synthesis of carbohydrate-based surfactants

    Energy Technology Data Exchange (ETDEWEB)

    Pemberton, Jeanne E.; Polt, Robin L.; Maier, Raina M.

    2016-11-22

    The present invention provides carbohydrate-based surfactants and methods for producing the same. Methods for producing carbohydrate-based surfactants include using a glycosylation promoter to link a carbohydrate or its derivative to a hydrophobic compound.

  2. Effects of Concentration and Conformation of Surfactants on Phase Separation of Surfactant-Water-Oil Systems

    Institute of Scientific and Technical Information of China (English)

    袁银权; 邹宪武; 刘昊阳

    2004-01-01

    The effects of surfactants on the phase separation of surfactant-water-oil systems have been investigated by using discontinuous molecular dynamic simulations. The phase separation speed and equilibrium configuration are dependent on the surfactant concentration and conformation. The equilibrium concentration of surfactants at the interface remains constant. With the increasing surfactant concentration, the equilibrium configuration crosses over from the disperse phase to the bicontinuous one. The crossover concentration is estimated. The conformation of the surfactant has little effect on the equilibrium concentration of surfactants at the interface,while it affects the equilibrium configuration after phase separation.

  3. Complex Formation Between Polyelectrolytes and Ionic Surfactants

    OpenAIRE

    1998-01-01

    The interaction between polyelectrolyte and ionic surfactant is of great importance in different areas of chemistry and biology. In this paper we present a theory of polyelectrolyte ionic-surfactant solutions. The new theory successfully explains the cooperative transition observed experimentally, in which the condensed counterions are replaced by ionic-surfactants. The transition is found to occur at surfactant densities much lower than those for a similar transition in non-ionic polymer-sur...

  4. Binding of cationic surfactants to humic substances

    NARCIS (Netherlands)

    Ishiguro, M.; Tan, W.; Koopal, L.K.

    2007-01-01

    Commercial surfactants are introduced into the environment either through waste products or site-specific contamination. The amphiphilic nature of both surfactants and humic substances (HS) leads to their mutual attraction especially when surfactant and HS are oppositely charged. Binding of the cati

  5. Surfactant analysis in oil-containing fluids

    Energy Technology Data Exchange (ETDEWEB)

    Gronsveld, J.; Faber, M.J. (Koninklijke Shell Exploratie en Produktie Laboratorium, Rijswijk (Netherlands))

    The total surfactant concentration in aqueous phase samples can be analysed with a potentiometric titration. In enhanced oil recovery research, however, the surfactant is produced not only in aqueous phase samples but also in oleic phase samples. The oleic constituents in the oliec phase samples interfere in the surfactant analysis and, therefore, the titration method has been adapted. (orig.).

  6. Surfactant adsorption to soil components and soils

    NARCIS (Netherlands)

    Ishiguro, Munehide; Koopal, Luuk K.

    2016-01-01

    Soils are complex and widely varying mixtures of organic matter and inorganic materials; adsorption of surfactants to soils is therefore related to the soil composition. We first discuss the properties of surfactants, including the critical micelle concentration (CMC) and surfactant adsorption on

  7. In vitro and in vivo CT imaging using bismuth sulfide modified with a highly biocompatible Pluronic F127

    Science.gov (United States)

    Chen, Jun; Yang, Xiao-Quan; Meng, Yuan-Zheng; Huang, Huan-Huan; Qin, Meng-Yao; Yan, Dong-Mei; Zhao, Yuan-Di; Ma, Zhi-Ya

    2014-07-01

    Probe bismuth sulfide modified with Pluronic F127 (Bi2S3-PF127), which has high biocompatibility and dispersibility, is synthesized using triblock copolymer Pluronic F127 to modify hydrophobic Bi2S3 nanoparticles that are prepared by a hot injection method. TEM results show that most of the probe has a length of about 14.85 ± 1.70 nm and a breadth of about 4.79 ± 0.63 nm. After injected into the tail vein of a mouse, the probe has obvious CT contrast enhancement capability from x-ray CT imaging results. Meanwhile, the probe’s in vivo toxicity is also studied. It is found that hematoxylin and eosin stains of major organs have no change. A biochemical analysis (alanine aminotransferase and aspartate aminotransferase) prove the probe has no adverse effects. The results of a blood analysis (white blood cell count, red blood cell count, hemoglobin, and platelet count) are also normal. The biological distribution of Bi by ICP-AES shows that most of nanoparticles are cleaned out after injection 48 h, and the circulation half-life of the probe is 5.0 h, suggesting that Bi2S3-PF127 has a long circulation and indicating that the Bi2S3-PF127 probe has good biocompatibility and safety.

  8. Inhibition of Growth and Metastasis of Colon Cancer by Delivering 5-Fluorouracil-loaded Pluronic P85 Copolymer Micelles

    Science.gov (United States)

    Zhu, Pengxi; Zhao, Naping; Sheng, Dandan; Hou, Jing; Hao, Chong; Yang, Xue; Zhu, Bing; Zhang, Shanshan; Han, Zhipeng; Wei, Lixin; Zhang, Li

    2016-01-01

    Hepatic metastasis is the leading cause of mortality of colon cancer, which is still lack of an effective therapy. A new delivery system, pluronic P85 block copolymers, conveying chemotherapeutic agent 5-fluorouracil (5-Fu) for inhibiting growth and metastasis of colon cancer was designed and developed. In this study, we demonstrated that 5-Fu produce strong pesticide effect at lower doses in the present of pluronic P85 compared with control groups. The migration and invasion of HCT116 cells and RKO cells were examined and the results showed that migration and invasion capacities of HCT116 cells and RKO cells were reduced by administering 5-Fu/P85 copolymer micelles in vitro and in vivo which indicating an effectively activity. Interestingly, the content of CD133 + CXCR4+ cells in HCT116 cancer cells and RKO cells treated by 5-Fu/P85 copolymer micelles was decreased. Importantly, the epithelial-mesenchymal transition (EMT) of CD133 + CXCR4+ cells, which was strongly associated with liver metastasis of colon cancer, was also suppressed by giving 5-Fu/P85 copolymer micelles. The results indicated that 5-Fu/P85 copolymer micelles could inhibit the growth and metastasis of colon cancer, which could be attributed to the decrease of the content of CD133 + CXCR4+ cells and suppression of EMT of CD133 + CXCR4+ cells. PMID:26864651

  9. 3D Printing of Aniline Tetramer-Grafted-Polyethylenimine and Pluronic F127 Composites for Electroactive Scaffolds.

    Science.gov (United States)

    Dong, Shi-Lei; Han, Lu; Du, Cai-Xia; Wang, Xiao-Yu; Li, Lu-Hai; Wei, Yen

    2017-02-01

    Electroactive hydrogel scaffolds are fabricated by the 3D-printing technique using composites of 30% Pluronic F127 and aniline tetramer-grafted-polyethylenimine (AT-PEI) copolymers with various contents from 2.5% to 10%. The synthesized AT-PEI copolymers can self-assemble into nanoparticles with the diameter of ≈50 nm and display excellent electroactivity due to AT conjugation. The copolymers are then homogeneously distributed into 30% Pluronic F127 solution by virtue of the thermosensitivity of F127, denoted as F/AT-PEI composites. Macroscopic photographs of latticed scaffolds elucidate their excellent printability of F/AT-PEI hydrogels for the 3D-printing technique. The conductivities of the printed F/AT-PEI scaffolds are all higher than 2.0 × 10(-3) S cm(-1) , which are significantly improved compared with that of F127 scaffold with only 0.94 × 10(-3) S cm(-1) . Thus, the F/AT-PEI scaffolds can be considered as candidates for application in electrical stimulation of tissue regeneration such as repair of muscle and cardiac nerve tissue. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. Preliminary investigation of commercially available pluronics as UV curable 3D printing inks for tissue engineering applications

    Science.gov (United States)

    Allen, A'Lester Cordell

    Three-dimensional printing (3DP) emerged from simple beginnings in the field of additive manufacturing (AM) over 31 years ago as an economical technique for rapid prototyping. Now 3DP has become the premier method for fabricating materials from unique consumer products to lifesaving customized human organs. Current challenges in bioprinting center around balancing material properties such as stiffness, yield strength, and surface chemistry with non-Newtonian fluid flow to construct interconnected, porous scaffolding geometries that simulate the complex vasculature found in the extracellular matrix (ECM) of the human body needed to promote cell growth and regeneration. In this study, several copolymers of poly(ethlyene oxide) and poly(propylene oxide) with a triblock structure were characterized using oscillatory shear measurements and thermogravimetric instruments to investigate the relationship between storage and loss moduli (G' and G") and printing behavior. The relationship between complex viscosity (eta*), yield stress (tauy), and fluid flow through a syringe yields some indirect correlations that depend on testing procedure. The overall relationship was more complex than originally understood. In the end, several self-supporting complex geometries were successfully printed using a photocurable formulations waxy (Pluronic P85, Jeffamine ED 2003) and liquid (Pluronic L121) triblock copolymers.

  11. Persurf, a new method to improve surfactant delivery: a study in surfactant depleted rats.

    Directory of Open Access Journals (Sweden)

    Wolfram Burkhardt

    Full Text Available PURPOSE: Exogenous surfactant is not very effective in adults with ARDS, since surfactant does not reach atelectatic alveoli. Perfluorocarbons (PFC can recruit atelectatic areas but do not replace impaired endogenous surfactant. A surfactant-PFC-mixture could combine benefits of both therapies. The aim of the proof-of-principal-study was to produce a PFC-in-surfactant emulsion (Persurf and to test in surfactant depleted Wistar rats whether Persurf achieves I. a more homogenous pulmonary distribution and II. a more homogenous recruitment of alveoli when compared with surfactant or PFC alone. METHODS: Three different PFC were mixed with surfactant and phospholipid concentration in the emulsion was measured. After surfactant depletion, animals either received 30 ml/kg of PF5080, 100 mg/kg of stained (green dye Curosurf™ or 30 ml/kg of Persurf. Lungs were fixated after 1 hour of ventilation and alveolar aeration and surfactant distribution was estimated by a stereological approach. RESULTS: Persurf contained 3 mg/ml phospholipids and was stable for more than 48 hours. Persurf-administration improved oxygenation. Histological evaluation revealed a more homogenous surfactant distribution and alveolar inflation when compared with surfactant treated animals. CONCLUSIONS: In surfactant depleted rats administration of PFC-in-surfactant emulsion leads to a more homogenous distribution and aeration of the lung than surfactant alone.

  12. Pluronic-based micelle encapsulation potentiates myricetin-induced cytotoxicity in human glioblastoma cells

    Directory of Open Access Journals (Sweden)

    Tang XJ

    2016-10-01

    Full Text Available Xiang-Jun Tang,1,* Kuan-Ming Huang,1,* Hui Gui,1,* Jun-Jie Wang,2 Jun-Ti Lu,1 Long-Jun Dai,1,3 Li Zhang,1 Gang Wang2 1Department of Neurosurgery, TaiHe Hospital, Hubei University of Medicine, Shiyan, 2Department of Pharmaceutics, Shanghai Eighth People’s Hospital, Jiangsu University, Shanghai, People’s Republic of China; 3Department of Surgery, University of British Columbia, Vancouver, BC, Canada *These authors contributed equally to this work Abstract: As one of the natural herbal flavonoids, myricetin has attracted much research interest, mainly owing to its remarkable anticancer properties and negligible side effects. It holds great potential to be developed as an ideal anticancer drug through improving its bioavailability. This study was performed to investigate the effects of Pluronic-based micelle encapsulation on myricetin-induced cytotoxicity and the mechanisms underlying its anticancer properties in human glioblastoma cells. Cell viability was assessed using a methylthiazol tetrazolium assay and a real-time cell analyzer. Immunoblotting and quantitative reverse transcriptase polymerase chain reaction techniques were used for determining the expression levels of related molecules in protein and mRNA. The results indicated that myricetin-induced cytotoxicity was highly potentiated by the encapsulation of myricetin. Mitochondrial apoptotic pathway was demonstrated to be involved in myricetin-induced glioblastoma cell death. The epidermal growth factor receptor (EGFR/PI3K/Akt pathway located in the plasma membrane and cytosol and the RAS-ERK pathway located in mitochondria served as upstream and downstream targets, respectively, in myricetin-induced apoptosis. MiR-21 inhibitors interrupted the expression of EGFR, p-Akt, and K-Ras in the same fashion as myricetin-loaded mixed micelles (MYR-MCs and miR-21 expression were dose-dependently inhibited by MYR-MCs, indicating the interaction of miR-21 with MYR-MCs. This study provided evidence

  13. Physical properties of botanical surfactants.

    Science.gov (United States)

    Müller, Lillian Espíndola; Schiedeck, Gustavo

    2017-08-24

    Some vegetal species have saponins in their composition with great potential to be used as natural surfactants in organic crops. This work aims to evaluate some surfactants physical properties of Quillaja brasiliensis and Agave angustifolia, based on different methods of preparation and concentration. The vegetal samples were prepared by drying and grinding, frozen and after chopped or used fresh and chopped. The neutral bar soap was used as a positive control. The drying and grinding of samples were the preparation method that resulted in higher foam column height in both species but Q. brasiliensis was superior to A. angustifolia in all comparisons and foam index was 2756 and 1017 respectively. Critical micelle concentration of Q. brasiliensis was 0.39% with the superficial tension of 54.40mNm(-1) while neutral bar soap was 0.15% with 34.96mNm(-1). Aspects such as genetic characteristics of the species, environmental conditions, and analytical methods make it difficult to compare the results with other studies, but Q. brasiliensis powder has potential to be explored as a natural surfactant in organic farming. Not only the surfactants physical properties of botanical saponins should be taken into account but also its effect on insects and diseases control when decided using them. Copyright © 2017 Elsevier B.V. All rights reserved.

  14. Interactions of Ovalbumin with Ionic Surfactants

    Institute of Scientific and Technical Information of China (English)

    GUO Xia; YAN Hui; GUO Rong

    2008-01-01

    The interactions of ovalbumin (OVA) with one anionic surfactant,sodium dodecyl sulfate (SDS),and two cationic surfactants,dodecyl trimethylammonium bromide (DTAB) and cetyl trimethylammonium bromide (CTAB),in water have been studied through fluorescence and UV-Vis spectroscopies and transmission electronic microscopy,combined with the measurement of conductivity.OVA can increase the critical micelle concentrations (cmc) of SDS and CTAB but has little effect on that of DTAB.The interaction between surfactant monomer and OVA is greater than that between surfactant micelles and OVA.Moreover,SDS can make OVA unfolded while cationic surfactants cannot.

  15. Surfactant gene polymorphisms and interstitial lung diseases

    Directory of Open Access Journals (Sweden)

    Pantelidis Panagiotis

    2001-11-01

    Full Text Available Abstract Pulmonary surfactant is a complex mixture of phospholipids and proteins, which is present in the alveolar lining fluid and is essential for normal lung function. Alterations in surfactant composition have been reported in several interstitial lung diseases (ILDs. Furthermore, a mutation in the surfactant protein C gene that results in complete absence of the protein has been shown to be associated with familial ILD. The role of surfactant in lung disease is therefore drawing increasing attention following the elucidation of the genetic basis underlying its surface expression and the proof of surfactant abnormalities in ILD.

  16. An anionic surfactant for EOR applications

    Science.gov (United States)

    Sagir, Muhammad; Tan, Isa M.; Mushtaq, Muhammad

    2014-10-01

    This work is to investigate the new anionic surfactants for the Enhanced Oil Recovery (EOR) application. Sulfonated anionic surfactant was produced by attaching SO3 to an ethoxylated alcohol to increase the performance of the surfactant. Methallyl chloride and ethoxylated alcohol was reacted followed by the reaction with sodium bisulfite to produce anionic sulfonated surfactant in 80.3 % yield. The sulfonation reaction parameters such as reactants mole ratio, reaction temperature and catalyst amount were optimized. The generation and stability of foam from the synthesized surfactant is also tested and results are reported. The synthesized novel surfactant was further investigated for the effect on the CO2 mobility in porous media and the findings are presented here. This in house developed surfactant has a great potential for CO2- EOR applications.

  17. Gelation and micellization behaviors of pluronic(®) F127 hydrogel containing poly(isobutylcyanoacrylate) nanoparticles specifically designed for mucosal application.

    Science.gov (United States)

    Pradines, Bénédicte; Djabourov, Madeleine; Vauthier, Christine; Loiseau, Philippe M; Ponchel, Gilles; Bouchemal, Kawthar

    2015-11-01

    The aim of this investigation is to combine the advantages of pluronic(®) F127 hydrogels and nanoparticles composed of poly(isobutylcyanoacrylate) (PIBCA) core coated with a mixture of chitosan and thiolated chitosan to design novel multifunctional formulation for mucosal application. Nanoparticles offer the advantage of being mucoadhesive while pluronic(®) F127 hydrogel allowed prolonged contact time onto mucosal surfaces. This work highlights an unprecedented comprehensive study on the effect of nanoparticles on gelation and micellization behaviors of pluronic(®) F127 using rheology and micro-calorimetry experiments. Results showed that presence of nanoparticles induced (i) smaller crystal peak of F127, (ii) a decrease of the enthalpy of F127 micellization and (iii) a non-reversibility of micelle formation (during heating ramp) and micelle melting (during cooling ramp). Together, these findings suggest that a part of F127 was not able to associate into micelles and the formation of mixed micelles containing F127 unimers and PIBCA/(chitosan/thiolated chitosan) copolymer and/or PIBCA homopolymer was suspected. The interaction of F127 unimers with nanoparticles resulted from their physical de-structuration as revealed by nanoparticle size measurement. In addition, we found that short polymerization duration of one hour induced more pronounced nanoparticle de-structuration. Twenty-four hour-polymerization of isobutylcyanoacrylate in the presence of chitosan and thiolated chitosan led to more stable nanoparticles when mixed with pluronic(®) F127.

  18. Evaluation of the stability of promethazine hydrochloride in pluronic lecithin organogel and the determination of an appropriate beyond-use date.

    Science.gov (United States)

    Peacock, Gina F; Sauvageot, Jurgita

    2014-01-01

    Previous reports indicate that pharmacists are assigning a wide variety of beyond-use dates to extemporaneously compounded medications in topical Pluronic lecithin organogel. The objective of this study was to evaluate the stability of promethazine in Pluronic lecithin organogel over a period of six months and to determine an appropriate beyond-use date. A stability-indicating high-performance liquid chromatography method for promethazine in Pluronic lecithin organogel was validated in our laboratory. Samples of each formulation were analyzed by high- performance liquid chromatography at 0, 7, 14, 21, 28, 45, 60, 90, and 180 days. At each time point, the average concentration and average percent of initial concentration were calculated. The beyond-use date was determined at the time period that the samples were physically stable and maintained at least 90% of the initial concentration. Promethazine hydrochloride was chemically stable in Pluronic lecithin organogel for the period of six months. However, the formulation was physically stable only up to 60 days, and the gel matrix showed signs of physical instability at 90 days, therefore, a 60-day beyond-use date is appropriate for this formulation.

  19. The influence of pluronic P123 micelles on corrosion behaviour of steel in cement extract and bulk matrix properties of cement paste

    NARCIS (Netherlands)

    Koleva, D.A.; Denkova, A. .G.; Hu, J.; van Breugel, K.

    2012-01-01

    The influence of Pluronic P123 (PEO20-PPO20-PEO70) micelles (of 10 nm size) on the corrosion behaviour of low carbon steel in cement extract (CE) was studied using electrochemical impedance spectroscopy (EIS) and potentio-dynamic polarisation (PDP). Additionally, mercury intrusion porosimetry (MIP)

  20. Coarse grained study of pluronic F127: Comparison with shorter co-polymers in its interaction with lipid bilayers and self-aggregation in water

    Science.gov (United States)

    Wood, I.; Martini, M. F.; Albano, J. M. R.; Cuestas, M. L.; Mathet, V. L.; Pickholz, M.

    2016-04-01

    The aim of this work is to understand the interactions of the poloxamer Pluronic F127, with lipid bilayers and its ability to self-associate in an aqueous environment. Molecular dynamics simulations at the coarse-grain scale were performed to address the behavior of single Pluronic F127 and shorter poloxamers unimers in palmitoyl-oleoyl-phosphatidyl-choline model membranes. According to the initial conditions and the poly-ethylene oxide/poly-propylene oxide composition, in water phase the unimer chain collapses into a coil conformation or adopts an interphacial U-shaped - or membrane spanning - distribution. A combination of poly-propylene oxide length, and the poly-ethylene oxide ability to cover poly-propylene oxide, is determinant for the conformation adopted by the unimer in each phase. Results of the simulations showed molecular evidence of strong interaction between Pluronic F127 and model membranes both in stable U-shaped and span conformations. The knowledge of this interaction could contribute to improve drug permeation. Additionally, we investigated the aggregation of one hundred Pluronic F127 unimers in water forming a micelle-like structure, suitable to be used as drug delivery system models.

  1. Effects of Additives and Coagulant Temperature on Fabrication of High Performance PVDF/Pluronic F127 Blend Hollow Fiber Membranes via Nonsolvent Induced Phase Separation

    Institute of Scientific and Technical Information of China (English)

    Chun Heng Loh; Rong Wang

    2012-01-01

    Poly(vinylidene fluoride) (PVDF) has become one of the most popular materials for membrane preparation via nonsolvent induced phase separation (NIPS) process. In this study, an amphiphilic block copolymer, Pluronic F127, has been used as both a pore-former and a surface-modifier in the fabrication of PVDF hollow fibermembranes to enhance the membrane permeability and hydrophilicity. The effects of 2nd additive and coagulant temperature on the formation of PVDF/Pluronic F 127 membranes have also been investigated. The as-spun hollow fibers were characterized in terms of cross-sectional morphology, pure water permeation (PWP), relative molecular mass cut-off (MWCO), membrane chemistry, and hydrolphilicity. It was obsered that the addition of Pluronic F 127 significantly increased the PWP of as-spun fibers, while the membrane contact angle was reduced. However, the size of macrovoids in the membranes was undesirably large. The addition of a 2nd additive, including lithium chloride (LiC1) and water, or an increase in coagulant temperature was found to effectively suppress the macrovoid for- mation in the Pluronic-containing membranes. In addition, the use of LiC1 as a 2nd additive also further enhanced the PWP and hydrophilicity of the membranes, while the surface pore size became smaller. PVDF hollow fiber with a PWP as high as 2330 L·m-2·h-1·MPa-1, a MWCO of 53000 and'a contact angle of 71 o was successfully fabricated with 3% (by mass) of Pluronic F127 and 3% (by mass) of LiC1 at a coagulant temperature of 25 ℃, which shows better performance as compared with most of PVDF hollow fiber membranes made by NIPS method.

  2. Adsorption of dimeric surfactants in lamellar silicates

    Energy Technology Data Exchange (ETDEWEB)

    Balcerzak, Mateusz; Pietralik, Zuzanna [Department of Macromolecular Physics, Faculty of Physics, A. Mickiewicz University, Umultowska 85, 61-614 Poznań (Poland); Domka, Ludwik [Department of Metalorganic Chemistry, Faculty of Chemistry, A. Mickiewicz University, Grunwaldzka 6, 60-780 Poznań (Poland); Skrzypczak, Andrzej [Institute of Chemical Technology, Poznań University of Technology, Berdychowo 4, 60-965 Poznań (Poland); Kozak, Maciej, E-mail: mkozak@amu.edu.pl [Department of Macromolecular Physics, Faculty of Physics, A. Mickiewicz University, Umultowska 85, 61-614 Poznań (Poland)

    2015-12-01

    Highlights: • The intercalation of dimeric surfactants changed the morphology of MMT samples. • XRD indicated structures formed by surfactant molecules in interlayer space. • The four-step thermal decomposition of dimeric surfactant, confirms intercalation. - Abstract: The adsorption of different types of cationic surfactants in lamellar silicates changes their surface character from hydrophilic to hydrophobic. This study was undertaken to obtain lamellar silicates modified by a series of novel dimeric (gemini) surfactants of different length alkyl chains and to characterise these organophilised materials. Synthetic sodium montmorillonite SOMASIF® ME 100 (M) and enriched bentonite of natural origin (Nanoclay – hydrophilic bentonite®) were organophilised with dimeric (gemini) surfactants (1,1′-(1,4-butanediyl)bis(alkoxymethyl)imidazolium dichlorides). As a result of surfactant molecule adsorption in interlamellar space, the d-spacing (d{sub 001}) increased from 0.97 nm (for the anhydrous structure) to 2.04 nm. A Fourier transform infrared spectroscopy (FTIR) analysis of the modified systems reveals bands assigned to the stretching vibrations of the CH{sub 2} and CH{sub 3} groups and the scissoring vibrations of the NH group from the structure of the dimeric surfactants. Thermogravimetric (TG) and derivative thermogravimetric (DTG) studies imply a four-stage process of surfactant decomposition. Scanning electron microscopy (SEM) images provide information on the influence of dimeric surfactant intercalation into the silicate structures. Particles of the modified systems show a tendency toward the formation of irregularly shaped agglomerates.

  3. Surfactants in tribology, v.3

    CERN Document Server

    Biresaw, Girma

    2013-01-01

    The manufacture and use of almost every consumer and industrial product rely on application of advanced knowledge in surface science and tribology. These two disciplines are of critical importance in major economic sectors, such as mining, agriculture, manufacturing (including metals, plastics, wood, computers, MEMS, NEMS, appliances), construction, transportation, and medical instruments, transplants, and diagnostic devices. An up-to-date reference with contributions by experts in surface science and tribology, Surfactants in Tribology, Volume 3 discusses some of the underlying tribological a

  4. Anaerobic Biodegradation of Detergent Surfactants

    OpenAIRE

    Erich Jelen; Ute Merrettig-Bruns

    2009-01-01

    Detergent surfactantscan be found in wastewater in relevant concentrations. Most of them are known as ready degradable under aerobic conditions, as required by European legislation. Far fewer surfactants have been tested so far for biodegradability under anaerobic conditions. The natural environment is predominantly aerobic, but there are some environmental compartments such as river sediments, sub-surface soil layer and anaerobic sludge digesters of wastewater treatment plants which have str...

  5. Study of a controlled release polymeric system based on Pluronic P123: Spectroscopic characterization and theoretical model approach

    Science.gov (United States)

    Arroyo, E.; Luque, P. A.; Cosio, M.; Soto, C.; Villarreal, R.; Nava, O.; Olivas, A.

    2017-06-01

    This work reports the profiles of drug release systems based on different polymers for the potential use as a skin anti-inflammatory. The materials used for the encapsulation of indomethacin were Pluronic P123 with various combinations of poly-ethylene-glycol and poly-N-vinyl pyrrolidone. These systems were characterized via Fourier transform infrared spectrometry and high resolution transmission electron microscopy. The morphology showed the treated polymers as spheres. Drug loadings were carried out via the absorption in solution method; this load was of a 1:10 wt ratio indomethacin to polymers. Drug release tests were performed via the dialysis method pH 7.2 phosphate buffered saline at 32 °C. The drug concentration was determined via UV-Vis spectroscopy, and additionally, a theoretical model was developed based on diffusion equations to describe the phenomenon. Comparison between the experimental results and theory was close to 5%.

  6. Effect of chain length of PEO on the gelation and micellization of the pluronic F127 copolymer aqueous system.

    Science.gov (United States)

    Pragatheeswaran, Abhinav Maheswaran; Chen, Shing Bor

    2013-08-06

    The effect of adding homopolymer poly(ethylene oxide) (PEO) on the sol/gel behavior of amphiphilic triblock copolymer Pluronic F127 ((EO)98(PO)67(EO)98) in aqueous media is explored. Emphasis is placed on the influence of the PEO molecular weight and concentration on micellization and gelation and the exploration of their correlation. PEO is always found to lower the critical micellization temperature modestly. However, short PEO chains promote the gelation of F127, and long chains delay or even curb gel formation. Micelle size measurements and cryo-TEM micrographs provide evidence for micellar aggregation via the bridging of long PEO chains or depletion flocculation, thereby impeding the ordering of micelles for gel formation.

  7. Hybrid chitosan–Pluronic F-127 films with BaTiO{sub 3}:Co nanoparticles: Synthesis and properties

    Energy Technology Data Exchange (ETDEWEB)

    Fuentes, S., E-mail: sfuentes@ucn.cl [Departamento de Ciencias Farmacéuticas, Facultad de Ciencias, Universidad Católica del Norte, Casilla 1280, Antofagasta (Chile); Center for the Development of Nanoscience and Nanotechnology, CEDENNA, Santiago (Chile); Dubo, J. [Departamento de Ciencias Farmacéuticas, Facultad de Ciencias, Universidad Católica del Norte, Casilla 1280, Antofagasta (Chile); Barraza, N. [Departamento de Física, Facultad de Ciencias, Universidad Católica del Norte, Casilla 1280, Antofagasta (Chile); González, R. [Laboratorio de Magnetismo, Departamento de Ciencias Geológicas, Universidad Católica del Norte, Antofagasta (Chile); Veloso, E. [Dirección de Investigaciones Científicas y Tecnológicas, Pontificia Universidad Católica de Chile, Avenida Vicuña Mackenna 4860, Santiago (Chile)

    2015-03-01

    In this study, magnetic BaTiO{sub 3}:Co (BT:Co) nanoparticles prepared using a combined sol–gel–hydrothermal technique were dispersed in a chitosan/Pluronic F-127 solution (QO/Pl) to obtain a nanocomposite hybrid films. Nanoparticles and hybrid films were characterized by X-ray powder diffraction, Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM) and alternating gradient magnetometry (AGM). Experimental results indicated that the BT:Co nanoparticles were encapsulated in the QO/Pl hybrid films and that the magnetic properties of the QO/Pl/BT:Co nanocomposites are similar to the naked BT:Co nanoparticles. Results indicate that Co doping produces an enhancement in the ferromagnetic behavior of the BT nanoparticle. The coating restricts this enhancement only to low-fields, leaving the diamagnetic behavior of BT at high-fields. Magnetically stable sizes (PSD) were obtained at 3% Co doping for both naked nanoparticles and hybrid films. These show an increased magnetic memory capacity and a softer magnetic hardness with respect to non-doped BT nanoparticles. - Highlights: • We described the synthesis of magnetic BaTiO{sub 3}:Co dispersed in chitosan (QO)/Pluronic F-127 (Pl) solution by sonication to obtain nanocomposite hybrid films. • We describe the physical and magnetic properties of BaTiO{sub 3}:Co nanoparticles and QO/Pl/BT:Co hybrid films. • The magnetic properties are defines by the presence of magnetic domains. These magnetic domains are close related with the amount of Co in the host lattice. • The prepared phases could be considered as multifunctional materials, with magnetic and ferri-electrical properties, with potential uses in the design of devices.

  8. Surfactant inhibition in acute respiratory failure : consequences for exogenous surfactant therapy

    NARCIS (Netherlands)

    E.P. Eijking (Eric)

    1993-01-01

    textabstractThe neonatal respiratory distress syndrome (RDS) is characterized by immaturity of the lung, resulting in relative or absolute absence of pulmonary surfactant. Worldwide, neonates suffering from RDS have been treated successfully with exogenous surfactant preparations. Currently, exogeno

  9. Cationic versus anionic surfactant in tuning the structure and interaction of nanoparticle, protein, and surfactant complexes.

    Science.gov (United States)

    Mehan, Sumit; Aswal, Vinod K; Kohlbrecher, Joachim

    2014-08-26

    The structure and interaction in complexes of anionic Ludox HS40 silica nanoparticle, anionic bovine serum albumin (BSA) protein, and cationic dodecyl trimethylammonium bromide (DTAB) surfactant have been studied using small-angle neutron scattering (SANS). The results are compared with similar complexes having anionic sodium dodecyl sulfate (SDS) surfactant (Mehan, S; Chinchalikar, A. J.; Kumar, S.; Aswal, V. K.; Schweins, R. Langmuir 2013, 29, 11290). In both cases (DTAB and SDS), the structure in nanoparticle-protein-surfactant complexes is predominantly determined by the interactions of the individual two-component systems. The nanoparticle-surfactant (mediated through protein-surfactant complex) and protein-surfactant interactions for DTAB, but nanoparticle-protein (mediated through protein-surfactant complex) and protein-surfactant interactions for SDS, are found to be responsible for the resultant structure of nanoparticle-protein-surfactant complexes. Irrespective of the charge on the surfactant, the cooperative binding of surfactant with protein leads to micellelike clusters of surfactant formed along the unfolded protein chain. The adsorption of these protein-surfactant complexes for DTAB on oppositely charged nanoparticles gives rise to the protein-surfactant complex-mediated aggregation of nanoparticles (similar to that of DTAB surfactant). It is unlike that of depletion-induced aggregation of nanoparticles with nonadsorption of protein-surfactant complexes for SDS in similarly charged nanoparticle systems (similar to that of protein alone). The modifications in nanoparticle aggregation as well as unfolding of protein in these systems as compared to the corresponding two-component systems have also been examined by selectively contrast matching the constituents.

  10. Surfactant-enhanced cellulose nanocrystal Pickering emulsions.

    Science.gov (United States)

    Hu, Zhen; Ballinger, Sarah; Pelton, Robert; Cranston, Emily D

    2015-02-01

    The effect of surfactants on the properties of Pickering emulsions stabilized by cellulose nanocrystals (CNCs) was investigated. Electrophoretic mobility, interfacial tension, confocal microscopy and three-phase contact angle measurements were used to elucidate the interactions between anionic CNCs and cationic alkyl ammonium surfactants didecyldimethylammonium bromide (DMAB) and cetyltrimethylammonium bromide (CTAB). Both surfactants were found to adsorb onto CNCs with concentration-dependent morphology. At low concentrations, individual surfactant molecules adsorbed with alkyl tails pointing outward leading to hydrophobic CNCs. At higher concentrations, above the surfactant's apparent critical micelle concentration, surfactant aggregate morphologies on CNCs were inferred and the hydrophobicity of CNCs decreased. DMAB, which has two alkyl tails, rendered the CNCs more hydrophobic than CTAB which has only a single alkyl tail, at all surfactant concentrations. The change in CNC wettability from surfactant adsorption was directly linked to emulsion properties; adding surfactant increased the emulsion stability, decreased the droplet size, and controlled the internal phase of CNC Pickering emulsions. More specifically, a double transitional phase inversion, from oil-in-water to water-in-oil and back to oil-in-water, was observed for emulsions with CNCs and increasing amounts of DMAB (the more hydrophobic surfactant). With CNCs and CTAB, no phase inversion was induced. This work represents the first report of CNC Pickering emulsions with surfactants as well as the first CNC Pickering emulsions that can be phase inverted. The ability to surface modify CNCs in situ and tailor emulsions by adding surfactants may extend the potential of CNCs to new liquid formulations and extruded/spray-dried materials.

  11. Solubilization of Hydrophobic Dyes in Surfactant Solutions

    Directory of Open Access Journals (Sweden)

    Ali Reza Tehrani-Bagha

    2013-02-01

    Full Text Available In this paper, the use of surfactants for solubilization of hydrophobic organic dyes (mainly solvent and disperse dyes has been reviewed. The effect of parameters such as the chemical structures of the surfactant and the dye, addition of salt and of polyelectrolytes, pH, and temperature on dye solubilization has been discussed. Surfactant self-assemble into micelles in aqueous solution and below the concentration where this occurs—the critical micelle concentration (CMC—there is no solubilization. Above the CMC, the amount of solubilized dye increases linearly with the increase in surfactant concentration. It is demonstrated that different surfactants work best for different dyes. In general, nonionic surfactants have higher solubilization power than anionic and cationic surfactants. It is likely that the reason for the good performance of nonionic surfactants is that they allow dyes to be accommodated not only in the inner, hydrocarbon part of the micelle but also in the headgroup shell. It is demonstrated that the location of a dye in a surfactant micelle can be assessed from the absorption spectrum of the dye-containing micellar solution.

  12. Using biologically soft surfactants for dust suppression

    Energy Technology Data Exchange (ETDEWEB)

    Tkachenko, N.G.; Kolodiichak, V.K.; Motrii, A.E.; Severin, V.D.

    1982-07-01

    This article discusses environmental aspects of using surfactants in coal mines for dust suppression. Surfactants for underground black coal mines in the USSR are divided into three classes: so-called soft surfactants with a decomposition period from 1 to 3 days, hard surfactants with decomposition exceeding a month and an intermediary group. The decomposition process is analyzed; the role played by fermentation is stressed. Environmental effects of surfactant decomposition are evaluated. Selected surfactants tested in Soviet laboratories are described. The results of experimental use of diethanolamide as a surfactant for water injection in coal seams are evaluated. Wetting time amounts to 1 s when a 0.2% concentration is used. When surfactant concentration in water is reduced to 0.05% wetting time does not change; when concentration decreases to 0.025% wetting time increases to 3 s. Surfactant efficiency is investigated under operational conditions in a Donbass mine. Specifications of the working face, mining system and air pollution caused by a shearer loader are discussed. When diethanolamide is used dust suppression efficiency ranges from 86.4 to 90.4%. During the tests diethanolamide concentration in water was 0.05%.

  13. Remediation using trace element humate surfactant

    Energy Technology Data Exchange (ETDEWEB)

    Riddle, Catherine Lynn; Taylor, Steven Cheney; Bruhn, Debra Fox

    2016-08-30

    A method of remediation at a remediation site having one or more undesirable conditions in which one or more soil characteristics, preferably soil pH and/or elemental concentrations, are measured at a remediation site. A trace element humate surfactant composition is prepared comprising a humate solution, element solution and at least one surfactant. The prepared trace element humate surfactant composition is then dispensed onto the remediation site whereby the trace element humate surfactant composition will reduce the amount of undesirable compounds by promoting growth of native species activity. By promoting native species activity, remediation occurs quickly and environmental impact is minimal.

  14. Surfactant nebulisation : lung function, surfactant distribution and pulmonary blood flow distribution in lung lavaged rabbits

    NARCIS (Netherlands)

    Dijk, Peter H.; Heikamp, A; Bambang Oetomo, Sidarto

    1997-01-01

    Objective: Surfactant nebulisation is a promising alternative to surfactant instillation in newborns with the respiratory distress syndrome. Although less surfactant is deposited in the lung, it improves gas exchange, probably due to a superior distribution. We hypothesize that a more uniform distri

  15. Biophysical inhibition of pulmonary surfactant function by polymeric nanoparticles: role of surfactant protein B and C.

    Science.gov (United States)

    Beck-Broichsitter, Moritz; Ruppert, Clemens; Schmehl, Thomas; Günther, Andreas; Seeger, Werner

    2014-11-01

    The current study investigated the mechanisms involved in the process of biophysical inhibition of pulmonary surfactant by polymeric nanoparticles (NP). The minimal surface tension of diverse synthetic surfactants was monitored in the presence of bare and surface-decorated (i.e. poloxamer 407) sub-100 nm poly(lactide) NP. Moreover, the influence of NP on surfactant composition (i.e. surfactant protein (SP) content) was studied. Dose-elevations of SP advanced the biophysical activity of the tested surfactant preparation. Surfactant-associated protein C supplemented phospholipid mixtures (PLM-C) were shown to be more susceptible to biophysical inactivation by bare NP than phospholipid mixture supplemented with surfactant protein B (PLM-B) and PLM-B/C. Surfactant function was hindered owing to a drastic depletion of the SP content upon contact with bare NP. By contrast, surface-modified NP were capable of circumventing unwanted surfactant inhibition. Surfactant constitution influences the extent of biophysical inhibition by polymeric NP. Steric shielding of the NP surface minimizes unwanted NP-surfactant interactions, which represents an option for the development of surfactant-compatible nanomedicines.

  16. Surfactant nebulisation : lung function, surfactant distribution and pulmonary blood flow distribution in lung lavaged rabbits

    NARCIS (Netherlands)

    Dijk, Peter H.; Heikamp, A; Bambang Oetomo, Sidarto

    1997-01-01

    Objective: Surfactant nebulisation is a promising alternative to surfactant instillation in newborns with the respiratory distress syndrome. Although less surfactant is deposited in the lung, it improves gas exchange, probably due to a superior distribution. We hypothesize that a more uniform distri

  17. Hemolysis by surfactants--A review.

    Science.gov (United States)

    Manaargadoo-Catin, Magalie; Ali-Cherif, Anaïs; Pougnas, Jean-Luc; Perrin, Catherine

    2016-02-01

    An overview of the use of surfactants for erythrocyte lysis and their cell membrane action mechanisms is given. Erythrocyte membrane characteristics and its association with the cell cytoskeleton are presented in order to complete understanding of the erythrocyte membrane distortion. Cell homeostasis disturbances caused by surfactants might induce changes starting from shape modification to cell lysis. Two main mechanisms are hypothesized in literature which are osmotic lysis and lysis by solubilization even if the boundary between them is not clearly defined. Another specific mechanism based on the formation of membrane pores is suggested in the particular case of saponins. The lytic potency of a surfactant is related to its affinity for the membrane and the modification of the lipid membrane curvature. This is to be related to the surfactant shape defined by its hydrophobic and hydrophilic moieties but also by experimental conditions. As a consequence, prediction of the hemolytic potency of a given surfactant is challenging. Several studies are focused on the relation between surfactant erythrolytic potency and their physico-chemical parameters such as the critical micellar concentration (CMC), the hydrophile-lipophile balance (HLB), the surfactant membrane/water partition coefficient (K) or the packing parameter (P). The CMC is one of the most important factors considered even if a lytic activity cut-off effect points out that the only consideration of CMC not enough predictive. The relation K.CMC must be considered in addition to the CMC to predict the surfactant lytic capacity within the same family of non ionic surfactant. Those surfactant structure/lytic activity studies demonstrate the requirement to take into account a combination of physico-chemical parameters to understand and foresee surfactant lytic potency.

  18. New amphiphilic glycopolymers by click functionalization of random copolymers – application to the colloidal stabilisation of polymer nanoparticles and their interaction with concanavalin A lectin

    Directory of Open Access Journals (Sweden)

    Otman Otman

    2010-06-01

    Full Text Available Glycopolymers with mannose units were readily prepared by click chemistry of an azido mannopyranoside derivative and a poly(propargyl acrylate-co-N-vinyl pyrrolidone. These glycopolymers were used as polymer surfactants, in order to obtain glycosylated polycaprolactone nanoparticles. Optimum stabilization for long time storage was achieved by using a mixture of glycopolymers and the non-ionic triblock copolymer Pluronic® F-68. The mannose moieties are accessible at the surface of nanoparticles and available for molecular recognition by concanavalin A lectin. Interaction of mannose units with the lectin were evaluated by measuring the changes in nanoparticles size by dynamic light scattering in dilute media.

  19. Structured fluids polymers, colloids, surfactants

    CERN Document Server

    Witten, Thomas A

    2010-01-01

    Over the last thirty years, the study of liquids containing polymers, surfactants, or colloidal particles has developed from a loose assembly of facts into a coherent discipline with substantial predictive power. These liquids expand our conception of what condensed matter can do. Such structured-fluid phenomena dominate the physical environment within living cells. This book teaches how to think of these fluids from a unified point of view showing the far-reaching effects ofthermal fluctuations in producing forces and motions. Keeping mathematics to a minimum, the book seeks the simplest expl

  20. Innovation in surfactant therapy I: surfactant lavage and surfactant administration by fluid bolus using minimally invasive techniques.

    Science.gov (United States)

    Dargaville, Peter A

    2012-01-01

    Innovation in the field of exogenous surfactant therapy continues more than two decades after the drug became commercially available. One such innovation, lung lavage using dilute surfactant, has been investigated in both laboratory and clinical settings as a treatment for meconium aspiration syndrome (MAS). Studies in animal models of MAS have affirmed that dilute surfactant lavage can remove meconium from the lung, with resultant improvement in lung function. In human infants both non-randomised studies and two randomised controlled trials have demonstrated a potential benefit of dilute surfactant lavage over standard care. The largest clinical trial, performed by our research group in infants with severe MAS, found that lung lavage using two 15-ml/kg aliquots of dilute surfactant did not reduce the duration of respiratory support, but did appear to reduce the composite outcome of death or need for extracorporeal membrane oxygenation. A further trial of lavage therapy is planned to more precisely define the effect on survival. Innovative approaches to surfactant therapy have also extended to the preterm infant, for whom the more widespread use of continuous positive airway pressure (CPAP) has meant delaying or avoiding administration of surfactant. In an effort to circumvent this problem, less invasive techniques of bolus surfactant therapy have been trialled, including instillation directly into the pharynx, via laryngeal mask and via brief tracheal catheterisation. In a recent clinical trial, instillation of surfactant into the trachea using a flexible feeding tube was found to reduce the need for subsequent intubation. We have developed an alternative method of brief tracheal catheterisation in which surfactant is delivered via a semi-rigid vascular catheter inserted through the vocal cords under direct vision. In studies to date, this technique has been relatively easy to perform, and resulted in rapid improvement in lung function and reduced need for

  1. Surfactant Adsorption: A Revised Physical Chemistry Lab

    Science.gov (United States)

    Bresler, Marc R.; Hagen, John P.

    2008-01-01

    Many physical chemistry lab courses include an experiment in which students measure surface tension as a function of surfactant concentration. In the traditional experiment, the data are fit to the Gibbs isotherm to determine the molar area for the surfactant, and the critical micelle concentration is used to calculate the Gibbs energy of micelle…

  2. Surfactant effects on soil aggregate tensile strength

    Science.gov (United States)

    Little is known regarding a soil aggregate's tensile strength response to surfactants that may be applied to alleviate soil water repellency. Two laboratory investigations were performed to determine surfactant effects on the tensile strength of 1) Ap horizons of nine wettable, agricultural soils co...

  3. Improved permeation performance and fouling-resistance of Poly(vinyl chloride/Polycarbonate blend membrane with added Pluronic F127

    Directory of Open Access Journals (Sweden)

    Supateekan Pacharasakoolchai

    2014-04-01

    Full Text Available The aim of this work was to prepare and characterize poly(vinyl chloride (PVC/polycarbonate (PC blend membranes for use in ultrafiltration. Pluronic F127 was used as an additive to modify the membrane surface of the PVC/PC blended membranes. The PVC/PC blend membrane was first prepared using the phase inversion method from a casting solution of PVC with small amount of PC in N-methylpyrrolidone (NMP and water as the non-solvent. The morphologies structure and properties, such as tensile strength, water flux, and bovine serum albumin (BSA rejection of the blend membrane were studied. Increased amounts of PC resulted in an increase in the water flux and ability to reject protein. A concentration of 0.75 wt% PC provided the best improvement in tensile strength of blend membrane. Addition of different amounts of pluronic F127 to the casting solution of PVC/PC with a PC concentration of 0.75 wt% resulted in a decrease in the water contact angle that demonstrated the improvement of hydrophilicity of blend membrane. Scanning electron microscopy photographs showed that the modified PVC/PC membranes had a bigger pore volume in the porous sub-layer compared to the PVC/PC control membrane. The PVC/PC membrane with added Pluronic F127 exhibited a much higher flux and rejection of BSA in a protein filtration experiment than the PVC/PC membrane. An increase in flux recovery ratio of PVC/PC/pluronic 127 blend membrane indicated that the modified membranes could reduce membrane fouling useful for ultrafiltration.

  4. The influence of pluronic P123 micelles on corrosion behaviour of steel in cement extract and bulk matrix properties of cement paste

    OpenAIRE

    Koleva, D. A.; Denkova, A. .G.; Hu, J; Breugel, K. van

    2012-01-01

    The influence of Pluronic P123 (PEO20-PPO20-PEO70) micelles (of 10 nm size) on the corrosion behaviour of low carbon steel in cement extract (CE) was studied using electrochemical impedance spectroscopy (EIS) and potentio-dynamic polarisation (PDP). Additionally, mercury intrusion porosimetry (MIP) was emplo ed to derive the impact of admixed micelles on porosity and pore-size distribution of cement paste. The motivation for carrying out this investigation has two main aspects: first, previou...

  5. Metathesis depolymerization for removable surfactant templates.

    Energy Technology Data Exchange (ETDEWEB)

    Zifer, Thomas (Sandia National Laboratories, Livermore, CA); Wheeler, David Roger; Rahimian, Kamayar; McElhanon, James Ross (Sandia National Laboratories, Livermore, CA); Long, Timothy Michael; Jamison, Gregory Marks; Loy, Douglas Anson (Los Alamos National Laboratories, Los Alamos, NM); Kline, Steven R. (National Institute of Standards and Technology, Gaithersburg, MD); Simmons, Blake Alexander (Sandia National Laboratories, Livermore, CA)

    2005-03-01

    Current methodologies for the production of meso- and nanoporous materials include the use of a surfactant to produce a self-assembled template around which the material is formed. However, post-production surfactant removal often requires centrifugation, calcination, and/or solvent washing which can damage the initially formed material architecture(s). Surfactants that can be disassembled into easily removable fragments following material preparation would minimize processing damage to the material structure, facilitating formation of templated hybrid architectures. Herein, we describe the design and synthesis of novel cationic and anionic surfactants with regularly spaced unsaturation in their hydrophobic hydrocarbon tails and the first application of ring closing metathesis depolymerization to surfactant degradation resulting in the mild, facile decomposition of these new compounds to produce relatively volatile nonsurface active remnants.

  6. Enhanced Oil Recovery with Surfactant Flooding

    DEFF Research Database (Denmark)

    Sandersen, Sara Bülow

    Enhanced oil recovery (EOR) is being increasingly applied in the oil industry and several different technologies have emerged during, the last decades in order to optimize oil recovery after conventional recovery methods have been applied. Surfactant flooding is an EOR technique in which the phase...... both for complex surfactant systems as well as for oil and brine systems. It is widely accepted that an increase in oil recovery can be obtained through flooding, whether it is simple waterflooding, waterflooding where the salinity has been modified by the addition or removal of specific ions (socalled...... “smart” waterflooding) or surfactant flooding. High pressure experiments have been carried out in this work on a surfactant system (surfactant/ oil/ brine) and on oil/ seawater systems (oil/ brine). The high pressure experiments were carried out on a DBR JEFRI PVT cell, where a glass window allows...

  7. Synthesis of 2-hydroxypropyl-β-cyclodextrin/pluronic-based polyrotaxanes via heterogeneous reaction as potential Niemann-Pick type C therapeutics.

    Science.gov (United States)

    Mondjinou, Yawo A; McCauliff, Leslie A; Kulkarni, Aditya; Paul, Lake; Hyun, Seok-Hee; Zhang, Zhaorui; Wu, Zhen; Wirth, Mary; Storch, Judith; Thompson, David H

    2013-12-01

    Five polyrotaxanes were synthesized by threading 2-hydroxypropyl-β-cyclodextrin (HP-β-CD) onto a variety of α,ω-ditriethylenediamino-N-carbamoyl-poly-(ethylene oxide)-block-poly(propylene oxide)-block-poly(ethylene oxide) (Pluronic) triblock copolymers using a two-pot strategy under heterogeneous, nonaqueous conditions. The threaded HP-β-CD units were retained on the pseudopolyrotaxane precursors by end-capping the branched diamine termini with sodium 2,4,6-trinitrobenzene sulfonate. Inclusion of the Pluronic copolymers within the HP-β-CD cavities was more favorable in nonpolar solvents, such as diethyl ether and n-hexane, both of which gave better coverage ratios than polar solvents. (1)H NMR and MALDI-TOF were used to estimate the average molecular weights of the purified polyrotaxane products. A globular morphology of aggregated polyrotaxanes was observed by tapping-mode AFM imaging of dried samples. Treatment of Niemann-Pick C (NPC) type 2-deficient fibroblasts with the polyrotaxane derivatives produced substantial reductions in sterol accumulation, as seen by diminished filipin staining in these cells, suggesting that Pluronic-based polyrotaxanes may be promising vehicles for delivery of HP-β-CD to cells with abnormal cholesterol accumulation.

  8. Fibrinogen stability under surfactant interaction.

    Science.gov (United States)

    Hassan, Natalia; Barbosa, Leandro R S; Itri, Rosangela; Ruso, Juan M

    2011-10-01

    Differential scanning calorimetry (DSC), circular dichroism (CD), difference spectroscopy (UV-vis), Raman spectroscopy, and small-angle X-ray scattering (SAXS) measurements have been performed in the present work to provide a quantitatively comprehensive physicochemical description of the complexation between bovine fibrinogen and the sodium perfluorooctanoate, sodium octanoate, and sodium dodecanoate in glycine buffer (pH 8.5). It has been found that sodium octanoate and dodecanoate act as fibrinogen destabilizer. Meanwhile, sodium perfluorooctanoate acts as a structure stabilizer at low molar concentration and as a destabilizer at high molar concentration. Fibrinogen's secondary structure is affected by all three studied surfactants (decrease in α-helix and an increase in β-sheet content) to a different extent. DSC and UV-vis revealed the existence of intermediate states in the thermal unfolding process of fibrinogen. In addition, SAXS data analysis showed that pure fibrinogen adopts a paired-dimer structure in solution. Such a structure is unaltered by sodium octanoate and perfluoroctanoate. However, interaction of sodium dodecanoate with the fibrinogen affects the protein conformation leading to a complex formation. Taken together, all results evidence that both surfactant hydrophobicity and tail length mediate the fibrinogen stability upon interaction. Copyright © 2011 Elsevier Inc. All rights reserved.

  9. Surfactant replacement therapy--economic impact.

    Science.gov (United States)

    Pejaver, R K; al Hifzi, I; Aldussari, S

    2001-06-01

    Surfactant replacement is an effective treatment for neonatal respiratory distress syndrome. (RDS). As widespread use of surfactant is becoming a reality, it is important to assess the economic implications of this new form of therapy. A comparison study was carried out at the Neonatal Intensive Care Unit (NICU) of Northwest Armed Forces Hospital, Saudi Arabia. Among 75 infants who received surfactant for RDS and similar number who were managed during time period just before the surfactant was available, but by set criteria would have made them eligible for surfactant. All other management modalities except surfactant were the same for all these babies. Based on the intensity of monitoring and nursing care required by the baby, the level of care was divided as: Level IIIA, IIIB, Level II, Level I. The cost per day per bed for each level was calculated, taking into account the use of hospital immovable equipment, personal salaries of nursing, medical, ancillary staff, overheads and maintenance, depreciation and replacement costs. Medications used, procedures done, TPN, oxygen, were all added to individual patient's total expenditure. 75 infants in the Surfactant group had 62 survivors. They spent a total of 4300 days in hospital. (av 69.35) Out of which 970 d (av 15.65 per patient) were ventilated days. There were 56 survivors in the non-surfactant group of 75. They had spent a total of 5023 days in the hospital (av 89.69/patient) out of which 1490 were ventilated days (av 26.60 d). Including the cost of surfactant (two doses), cost of hospital stay for each infant taking the average figures of stay would be SR 118, 009.75 per surfactant treated baby and SR 164, 070.70 per non-surfactant treated baby. The difference of 46,061 SR is 39.03% more in non-surfactant group. One Saudi rial = 8 Rs (approx at the time study was carried out.) Medical care cost varies from place to place. However, it is definitely cost-effective where surfactant is concerned. Quality adjusted

  10. Simulation of the Phase Separation of the Pluronic L64/Water/p - Xylene System Using MesoDyn%用介观动力学模拟Pluronic L64/水/p-Xylene体系的相分离

    Institute of Scientific and Technical Information of China (English)

    郭森立; 侯廷军; 徐筱杰

    2001-01-01

    用介观动力学在介观层次上对不同组分的Pluronic L64/水/p-xylene三元体系的相分离进行了研究,得到了和实验相吻合的结果.计算表明对于纯p-xylene溶剂和有含少量水的p-xylene溶剂,体系没有发生相分离,随着水的含量增加,体系发生了明显的相分离,产生了不同形态的胶团.本研究还通过对比不同溶剂组分下的体系介观形貌,讨论了水在体系相分离中的作用.同时通过分析模拟了1 000步后体系中水的分布,证实在胶团核中存在自由水(free water)的猜想.

  11. Surfactant-soil interactions during surfactant-amended remediation of contaminated soils by hydrophobic organic compounds: a review.

    Science.gov (United States)

    Laha, Shonali; Tansel, Berrin; Ussawarujikulchai, Achara

    2009-01-01

    Surfactants are amphiphilic molecules that reduce aqueous surface tension and increase the solubility of hydrophobic organic compounds (HOCs). Surfactant-amended remediation of HOC-contaminated soils and aquifers has received significant attention as an effective treatment strategy - similar in concept to using soaps and detergents as washing agents to remove grease from soiled fabrics. The proposed mechanisms involved in surfactant-amended remediation include: lowering of interfacial tension, surfactant solubilization of HOCs, and the phase transfer of HOC from soil-sorbed to pseudo-aqueous phase. However, as with any proposed chemical countermeasures, there is a concern regarding the fate of the added surfactant. This review summarizes the current state of knowledge regarding nonionic micelle-forming surfactant sorption onto soil, and serves as an introduction to research on that topic. Surfactant sorption onto soil appears to increase with increasing surfactant concentration until the onset of micellization. Sorbed-phase surfactant may account for the majority of added surfactant in surfactant-amended remediation applications, and this may result in increased HOC partitioning onto soil until HOC solubilization by micellar phase surfactant successfully competes with increased HOC sorption on surfactant-modified soil. This review provides discussion of equilibrium partitioning theory to account for the distribution of HOCs between soil, aqueous phase, sorbed surfactant, and micellar surfactant phases, as well as recently developed models for surfactant sorption onto soil. HOC partitioning is characterized by apparent soil-water distribution coefficients in the presence of surfactant.

  12. Different effects of surfactant proteins B and C - implications for development of synthetic surfactants.

    Science.gov (United States)

    Curstedt, Tore; Johansson, Jan

    2010-06-01

    Treatment of premature newborn rabbits with synthetic surfactants containing a surfactant protein C analogue in a simple phospholipid mixture gives similar tidal volumes as treatment with poractant alfa (Curosurf(R)) but ventilation with a positive end-expiratory pressure (PEEP) is needed for this synthetic surfactant to stabilize the alveoli at end-expiration. The effect on lung gas volumes seems to depend on the structure of the peptide since treatment with a synthetic surfactant containing the 21-residue peptide (LysLeu(4))(4)Lys (KL(4)) gives low lung gas volumes in experiments also performed with PEEP. Surfactant preparations containing both surfactant proteins B and C or their analogues prevent alveolar collapse at end-expiration even if ventilated without PEEP. Treatment of premature newborn rabbits with different natural surfactants indicates that both the lipid composition and the proteins are important in order to stabilize the alveoli at end-expiration. Synthetic surfactants containing two peptides may be able to replace natural surfactants within the near future but more trials need to be performed before any conclusion can be drawn about the ideal composition of this new generation of synthetic surfactants.

  13. Exogenous Pulmonary Surfactant as a Vehicle for Antimicrobials: Assessment of Surfactant-Antibacterial Interactions In Vitro

    Directory of Open Access Journals (Sweden)

    Alexei Birkun

    2014-01-01

    Full Text Available Owing to its unique surface-active properties, an exogenous pulmonary surfactant may become a promising drug delivery agent, in particular, acting as a vehicle for antibiotics in topical treatment of pneumonia. The purpose of this study was to assess a mutual influence of natural surfactant preparation and three antibiotics (amikacin, cefepime, and colistimethate sodium in vitro and to identify appropriate combination(s for subsequent in vivo investigations of experimental surfactant/antibiotic mixtures. Influence of antibiotics on surface-active properties of exogenous surfactant was assessed using the modified Pattle method. Effects of exogenous surfactant on antibacterial activity of antimicrobials against Staphylococcus aureus, Klebsiella pneumoniae, and Pseudomonas aeruginosa were evaluated using conventional microbiologic procedures. Addition of amikacin or cefepime to surfactant had no significant influence on surface-active properties of the latter. Obvious reduction of surface-active properties was confirmed for surfactant/colistimethate composition. When suspended with antibiotics, surfactant either had no impact on their antimicrobial activity (amikacin or exerted mild to moderate influence (reduction of cefepime bactericidal activity and increase of colistimethate bacteriostatic activity against S. aureus and P. aeruginosa. Considering favorable compatibility profile, the surfactant/amikacin combination is advisable for subsequent investigation of joint surfactant/antibacterial therapy in animals with bacterial pneumonia.

  14. Fluorescence emission of pyrene in surfactant solutions.

    Science.gov (United States)

    Piñeiro, Lucas; Novo, Mercedes; Al-Soufi, Wajih

    2015-01-01

    The systematic description of the complex photophysical behaviour of pyrene in surfactant solutions in combination with a quantitative model for the surfactant concentrations reproduces with high accuracy the steady-state and the time resolved fluorescence intensity of pyrene in surfactant solutions near the cmc, both in the monomer and in the excimer emission bands. We present concise model equations that can be used for the analysis of the pyrene fluorescence intensity in order to estimate fundamental parameters of the pyrene-surfactant system, such as the binding equilibrium constant K of pyrene to a given surfactant micelle, the rate constant of excimer formation in micelles, and the equilibrium constant of pyrene-surfactant quenching. The values of the binding equilibrium constant K(TX100)=3300·10³ M⁻¹ and K(SDS)=190·10³ M⁻¹ for Triton X-100 (TX100) and SDS micelles, respectively, show that the partition of pyrene between bulk water and micelles cannot be ignored, even at relatively high surfactant concentrations above the cmc. We apply the model to the determination of the cmc from the pyrene fluorescence intensity, especially from the intensity ratio at two vibronic bands in the monomer emission or from the ratio of excimer to monomer emission intensity. We relate the finite width of the transition region below and above the cmc with the observed changes in the pyrene fluorescence in this region.

  15. Tunable, antibacterial activity of silicone polyether surfactants.

    Science.gov (United States)

    Khan, Madiha F; Zepeda-Velazquez, Laura; Brook, Michael A

    2015-08-01

    Silicone surfactants are used in a variety of applications, however, limited data is available on the relationship between surfactant structure and biological activity. A series of seven nonionic, silicone polyether surfactants with known structures was tested for in vitro antibacterial activity against Escherichia coli BL21. The compounds varied in their hydrophobic head, comprised of branched silicone structures with 3-10 siloxane linkages and, in two cases, phenyl substitution, and hydrophilic tail of 8-44 poly(ethylene glycol) units. The surfactants were tested at three concentrations: below, at, and above their Critical Micelle Concentrations (CMC) against 5 concentrations of E. coli BL21 in a three-step assay comprised of a 14-24h turbidometric screen, a live-dead stain and viable colony counts. The bacterial concentration had little effect on antibacterial activity. For most of the surfactants, antibacterial activity was higher at concentrations above the CMC. Surfactants with smaller silicone head groups had as much as 4 times the bioactivity of surfactants with larger groups, with the smallest hydrophobe exhibiting potency equivalent to sodium dodecyl sulfate (SDS). Smaller PEG chains were similarly associated with higher potency. These data link lower micelle stability and enhanced permeability of smaller silicone head groups to antibacterial activity. The results demonstrate that simple manipulation of nonionic silicone polyether structure leads to significant changes in antibacterial activity.

  16. A study of surfactant-assisted waterflooding

    Energy Technology Data Exchange (ETDEWEB)

    Scamehorn, J F; Harwell, J H

    1990-09-01

    In surfactant-assisted waterflooding, a surfactant slug is injected into a reservoir, followed by a brine spacer, followed by second surfactant slug. The charge on the surfactant in the first slug has opposite sign to that in the second slug. When the two slugs mix in the reservoir, a precipitate or coacervate is formed which plugs the permeable region of the reservoir. Subsequently injected water or brine is forced through the low permeability region of the reservoir, increasing sweep efficiency of the waterflood, compared to a waterflood not using surfactants. In this part of the work, two major tasks are performed. First, core floods are performed with oil present to demonstrate the improvement in incremental oil production, as well as permeability modification. Second, a reservoir simulation model will be proposed to further delineate the optimum strategy for implementation of the surfactant-assisted waterflooding, as well as indicate the reservoir types for which it would be most effective. Surfactants utilized were sodium dodecyl sulfate and dodecyl pyridinium chloride. 44 refs., 17 figs., 3 tabs.

  17. Surfactants tailored by the class Actinobacteria

    Directory of Open Access Journals (Sweden)

    Johannes H Kügler

    2015-03-01

    Full Text Available Gloablly, the drive towards the establishment of a bio-based economy has resulted in an increased need for bio-based applications. This, in turn, has served as a driving force for the discovery and application of novel biosurfactants. The class Actinobacteria represents a vast group of microorganisms with the ability to produce a diverse range of secondary metabolites, including surfactants. Understanding the extensive nature of the biosurfactants produced by actinobacterial strains can assist in finding novel biosurfactants with new potential applications. This review therefore presents a comprehensive overview of the knowledge available on actinobacterial surfactants, the chemical structures that have been completely or partly elucidated, as well as the identity of the biosurfactant-producing strains. Producer strains of not yet elucidated compounds are discussed, as well as the original habitats of all the producer strains, which seems to indicate that biosurfactant production is environmentally driven. Methodology applied in the isolation, purification and structural elucidation of the different types of surface active compounds, as well as surfactant activity tests, are also discussed. Overall, actinobacterial surfactants can be summarized to include the dominantly occurring trehalose-comprising surfactants, other non-trehalose containing glycolipids, lipopeptides and the more rare actinobacterial surfactants. The lack of structural information on a large proportion of actinobacterial surfactants should be considered as a driving force to further explore the abundance and diversity of these compounds. This would allow for a better understanding of actinobacterial surface active compounds and their potential for biotechnological application.

  18. Influence of surfactants in forced dynamic dewetting.

    Science.gov (United States)

    Henrich, Franziska; Fell, Daniela; Truszkowska, Dorota; Weirich, Marcel; Anyfantakis, Manos; Nguyen, Thi-Huong; Wagner, Manfred; Auernhammer, Günter K; Butt, Hans-Jürgen

    2016-09-20

    In this work we show that the forced dynamic dewetting of surfactant solutions depends sensitively on the surfactant concentration. To measure this effect, a hydrophobic rotating cylinder was horizontally half immersed in aqueous surfactant solutions. Dynamic contact angles were measured optically by extrapolating the contour of the meniscus to the contact line. Anionic (sodium 1-decanesulfonate, S-1DeS), cationic (cetyl trimethylammonium bromide, CTAB) and nonionic surfactants (C4E1, C8E3 and C12E5) with critical micelle concentrations (CMCs) spanning four orders of magnitude were used. The receding contact angle in water decreased with increasing velocity. This decrease was strongly enhanced when adding surfactant, even at surfactant concentrations of 10% of the critical micelle concentration. Plots of the receding contact angle-versus-velocity almost superimpose when being plotted at the same relative concentration (concentration/CMC). Thus the rescaled concentration is the dominating property for dynamic dewetting. The charge of the surfactants did not play a role, thus excluding electrostatic effects. The change in contact angle can be interpreted by local surface tension gradients, i.e. Marangoni stresses, close to the three-phase contact line. The decrease of dynamic contact angles with velocity follows two regimes. Despite the existence of Marangoni stresses close to the contact line, for a dewetting velocity above 1-10 mm s(-1) the hydrodynamic theory is able to describe the experimental results for all surfactant concentrations. At slower velocities an additional steep decrease of the contact angle with velocity was observed. Particle tracking velocimetry showed that the flow profiles do not differ with and without surfactant on a scales >100 μm.

  19. Enhancing the oral bioavailability of biochanin A by encapsulation in mixed micelles containing Pluronic F127 and Plasdone S630

    Science.gov (United States)

    Wu, Xiaoyan; Ge, Weihong; Shao, Tengfei; Wu, Weijun; Hou, Jian; Cui, Li; Wang, Jing; Zhang, Zhenghai

    2017-01-01

    Biochanin A (BCA), a natural dietary isoflavone, has been reported to show anticancer activities. However, its low biological availability and poor aqueous solubility limit its usefulness as a chemotherapeutic agent. We developed BCA-loaded micelles with Pluronic F127 and Plasdone S630 (BCA-FS). The optimized, spherical-shaped BCA-FS was obtained at a ratio of 1:1 (F127:S630). The particle size was 25.17±1.2 nm, and the zeta potential was −10.9±0.24 mV. BCA solubility in water increased to 5.0 mg/mL after encapsulation, and the drug-loading efficiency was 5.88%±0.76%. In vitro release experiments showed a delayed release of BCA from the mixed micelles. Furthermore, the BCA absorption permeability across a Caco-2 cell monolayer from the apical side to the basolateral side increased by 54% in BCA-FS. A pharmacokinetics evaluation showed a 2.16-fold increase in the relative oral bioavailability of BCA-FS compared with raw BCA, indicating that the mixed micelles may promote absorption in the gastrointestinal tract. A gastrointestinal safety assay was used to assess the reliability and safety of BCA-FS. On the basis of these findings, we conclude that this simple nanomicelle system could be leveraged to deliver BCA and other hydrophobic drugs. PMID:28260893

  20. Evaluation of the stability of acetaminophen in pluronic lecithin organogel and the determination of an appropriate beyond-use date.

    Science.gov (United States)

    Peacock, Gina F; Sauvageot, Jurgita

    2012-01-01

    Transdermal acetaminophen in Pluronic lecithin organogel (APAP-PLO) has been anecdotally reported as beneficial when used in cancer patients in the hospice setting. However, there is currently no published information regarding the stability of APAP-PLO. The objective of this study was to identify an appropriate formulation of APAP-PLO and to evaluate the stability of that formulation in order to determine an appropriate beyond-use date. APAP-PLO 50% was prepared by a local compounding pharmacy and analyzed at 0, 7, 14, 28, 45, 60, 90, and 180 days using a stability-indicating high-performance liquid chromatographic method. The mean concentrations and standard deviations were determined for each time point. Physical stability was also assessed by visual observation at each time point. The beyond-use date was determined as the time period that the samples maintained at least 90 percent of the initial concentration. At 180 days, the APAP-PLO was physically stable as noted by visual observation, and the concentration was 102 +/- 4.8 percent of initial concentration indicating that a beyond-use date of 180 days would be appropriate for this formulation.

  1. Hybrid chitosan-Pluronic F-127 films with BaTiO3:Co nanoparticles: Synthesis and properties

    Science.gov (United States)

    Fuentes, S.; Dubo, J.; Barraza, N.; González, R.; Veloso, E.

    2015-03-01

    In this study, magnetic BaTiO3:Co (BT:Co) nanoparticles prepared using a combined sol-gel-hydrothermal technique were dispersed in a chitosan/Pluronic F-127 solution (QO/Pl) to obtain a nanocomposite hybrid films. Nanoparticles and hybrid films were characterized by X-ray powder diffraction, Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM) and alternating gradient magnetometry (AGM). Experimental results indicated that the BT:Co nanoparticles were encapsulated in the QO/Pl hybrid films and that the magnetic properties of the QO/Pl/BT:Co nanocomposites are similar to the naked BT:Co nanoparticles. Results indicate that Co doping produces an enhancement in the ferromagnetic behavior of the BT nanoparticle. The coating restricts this enhancement only to low-fields, leaving the diamagnetic behavior of BT at high-fields. Magnetically stable sizes (PSD) were obtained at 3% Co doping for both naked nanoparticles and hybrid films. These show an increased magnetic memory capacity and a softer magnetic hardness with respect to non-doped BT nanoparticles.

  2. Targeted delivery of anticancer drugs by aptamer AS1411 mediated Pluronic F127/cyclodextrin-linked polymer composite micelles.

    Science.gov (United States)

    Li, Xin; Yu, Yang; Ji, Qian; Qiu, Liyan

    2015-01-01

    Aptamers are single-stranded RNA or DNA ligands that can specifically bind to various molecular targets with high affinity. Owing to this unique character, they have become increasingly attractive in the field of drug delivery. In this study, we developed a multifunctional composite micelle (CM) with surface modification of aptamer AS1411 (Ap) for targeted delivery of doxorubicin (DOX) to human breast tumors. This binary mixed system consisting of AS1411 modified Pluronic F127 and beta-cyclodextrin-linked poly(ethylene glycol)-b-polylactide could enhance DOX-loading capacity and increase micelle stability. Cellular uptake of CM-Ap was found to be higher than that of untargeted CM due to the nucleolin-mediated endocytosis effect. In vivo study in MCF-7 tumor-bearing mice demonstrated that the AS1411-functionalized composite micelles showed prolonged circulation time in blood, enhanced accumulation in tumor, improved antitumor activity, and decreased cardiotoxicity. In conclusion, aptamer-conjugated multifunctional composite micelles could be a potential delivery vehicle for cancer therapy.

  3. Cytotoxicity of iron oxide nanoparticles made from the thermal decomposition of organometallics and aqueous phase transfer with Pluronic F127.

    Science.gov (United States)

    Gonzales, Marcela; Mitsumori, Lee M; Kushleika, John V; Rosenfeld, Michael E; Krishnan, Kannan M

    2010-01-01

    Magnetic nanoparticles are promising molecular imaging agents due to their relatively high relaxivity and the potential to modify surface functionality to tailor biodistribution. In this work we describe the synthesis of magnetic nanoparticles using organic solvents with organometallic precursors. This method results in nanoparticles that are highly crystalline and have uniform size and shape. The ability to create a monodispersion of particles of the same size and shape results in unique magnetic properties that can be useful for biomedical applications with MR imaging. Before these nanoparticles can be used in biological applications, however, means are needed to make the nanoparticles soluble in aqueous solutions and the toxicity of these nanoparticles needs to be studied. We have developed two methods to surface modify and transfer these nanoparticles to the aqueous phase using the biocompatible co-polymer, Pluronic F127. Cytotoxicity was found to be dependent on the coating procedure used. Nanoparticle effects on a cell-culture model were quantified using concurrent assaying: a lactate dehydrogenase assay to determine cytotoxicity and a 3-(4,5-dimethylthiazol-2-yl)-5-(3-carboxymethoxyphenyl)-2-(4-sulfophenyl)-2H-tetrazolium, inner salt assay to determine viability for a 24 h incubation period. Concurrent assaying was done to insure that nanoparticles did not interfere with the colorimetric assay results. This report demonstrates that a monodispersion of nanoparticles of uniform size and shape can be manufactured. Initial cytotoxicity testing of new molecular imaging agents needs to be carefully constructed to avoid interference and erroneous results.

  4. Evaluation of hydrogel composing of Pluronic F127 and carboxymethyl hexanoyl chitosan as injectable scaffold for tissue engineering applications.

    Science.gov (United States)

    Yap, Lie-Sian; Yang, Ming-Chien

    2016-10-01

    This study demonstrated a novel hydrogel system composing of Pluronic F127, carboxymethyl hexanoyl chitosan (CA) and glutaraldehyde (GA) for encapsulating fibroblasts (L-929). The thermal behavior of the hydrogel was evaluated using TGA, the swelling behavior of the hydrogel was evaluated in Dulbecco's Modified Eagle's medium (DMEM), and the mechanical properties were determined through dynamic mechanical analysis. Cells were encapsulated by simple mixing, and the viability of encapsulated cells was determined using alamar blue cell viability assay and the cells morphology was examined using fluorescent imaging. The results indicated that the Tgel of this system was around 30°C, where sol-gel transformation occurred within 90s. Although the addition of CA and GA reduced the shear moduli slightly, the F127/CA/GA gel was able to remain in gelling state in the medium for more than 1 month. In vitro cell culture study revealed that F-127/CA/GA hydrogels were non-cytotoxic. Moreover, the viability of encapsulated L929 was 106% after incubation for 5 days. Based on these results, these F127/CA/GA hydrogels can be used to encapsulate cells for tissue engineering applications.

  5. Surfactant-Assisted Coal Liquefaction

    Science.gov (United States)

    Hickey, Gregory S.; Sharma, Pramod K.

    1993-01-01

    Obtaining liquid fuels from coal which are economically competitive with those obtained from petroleum based sources is a significant challenge for the researcher as well as the chemical industry. Presently, the economics of coal liquefaction are not favorable because of relatively intense processing conditions (temperatures of 430 degrees C and pressures of 2200 psig), use of a costly catalyst, and a low quality product slate of relatively high boiling fractions. The economics could be made more favorable by achieving adequate coal conversions at less intense processing conditions and improving the product slate. A study has been carried out to examine the effect of a surfactant in reducing particle agglomeration and improving hydrodynamics in the coal liquefaction reactor to increase coal conversions...

  6. Gemini surfactants from natural amino acids.

    Science.gov (United States)

    Pérez, Lourdes; Pinazo, Aurora; Pons, Ramon; Infante, Mrosa

    2014-03-01

    In this review, we report the most important contributions in the structure, synthesis, physicochemical (surface adsorption, aggregation and phase behaviour) and biological properties (toxicity, antimicrobial activity and biodegradation) of Gemini natural amino acid-based surfactants, and some potential applications, with an emphasis on the use of these surfactants as non-viral delivery system agents. Gemini surfactants derived from basic (Arg, Lys), neutral (Ser, Ala, Sar), acid (Asp) and sulphur containing amino acids (Cys) as polar head groups, and Geminis with amino acids/peptides in the spacer chain are reviewed.

  7. Liquid-liquid extraction for surfactant-contaminant separation and surfactant reuse

    Energy Technology Data Exchange (ETDEWEB)

    Hasegawa, M.A. [Surbec Environmental, Norman, OK (United States); Sabatini, D.A.; Harwell, J.H. [Univ. of Oklahoma, Norman, OK (United States)

    1997-07-01

    Liquid-liquid extraction was investigated for use with surfactant enhanced subsurface remediation. A surfactant liquid-liquid extraction model (SLLEM) was developed for batch equilibrium conditions based on contaminant partitioning between micellar, water, and solvent phases. The accuracy of this fundamental model was corroborated with experimental results (using naphthalene and phenanthrene as contaminants and squalane as the extracting solvent). The SLLEM model was then expanded to nonequilibrium conditions. The effectiveness of this nonequilibrium model was corroborated with experimental results from continuous flow hollow fiber membrane systems. The validated models were used to conduct a sensitivity analysis evaluating the effects of surfactants on the removal of the contaminants in liquid-liquid extraction systems. In addition, liquid-liquid extraction is compared to air stripping for surfactant-contaminant separation. Finally, conclusions are drawn as to the impact of surfactants on liquid-liquid extraction processes, and the significance of these impacts on the optimization of surfactant-enhanced subsurface remediation.

  8. Synthesis and Characterization of Zirconia Nanocrystallites by Cationic Surfactant and Anionic Surfactant

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    Study on nanomaterials has attracted great interests in recent years. In this article,zirconia nanocrystallites of different structures have been successfully synthesized via hydrothermal methods with cationic surfactant (CTAB) and anionic surfactant (SDS), respectively. Differential Scanning Calorimeter (DSC-TG), X-ray Diffractometer (XRD), Transmission Electron Microscope (TEM), Ultraviolet-Visible (UV-vis) and N2 adsorption-desorption analyses are used for their structure characteristics. The results show that the cationic surfactant has a distinctive direction effect on the formation of zirconia nanocrystallites, while the anionic surfactant has a self-assembly synergistic effect on them. The sample synthesized with the cationic surfactant presents good dispersion with the main phase of tetragonal zirconia, and the average nanocryst al size is around 15nm after calcination at 500 ℃. While the sample synthesized with the anionic surfactant exhibits a worm-like mesoporous structure with pure tetragonal phase after calcination at 500 ℃ and with good thermal stability.

  9. Studies on the electrocapillary curves of anionic surfactants in presence of non-ionic surfactants.

    Science.gov (United States)

    Bembi, R; Goyal, R N; Malik, W U

    1976-09-01

    Polyoxyethylated non-ionic surfactants such as Tween 20, Tween 40, Nonidet P40 and Nonex 501 have been supposed to be associated with cationic characteristics. Studies on the effect of these surfactants on the electrocapillary curves of the anionic surfactants Aerosol IB, Manaxol OT and sodium lauryl sulphate (SLS), show that the electrocapillary maxima shift towards positive potentials. The order of adsorption of the anionic surfactants is SLS > Manaxol OT > Aerosol IB while the shift in maxima is in the order Aerosol IB ~ Manaxol OT > SLS which confirms association of cationic characteristics with the micelles of these non-ionic surfactants. The magnitude of the shift in electrocapillary maxima is Nonex 501 > Nonidet P40 > Tween 20 > Tween 40 which may be the order of magnitude of the positive charge carried by these non-ionic surfactants.

  10. Synthesis of novel quaternary ammonium surfactants containing adamantane

    Institute of Scientific and Technical Information of China (English)

    Jian Wei Guo; Xing Zhong; Hua Zhu; Li Juan Feng; Ying De Cui

    2012-01-01

    A series of novel quaternary ammonium surfactants containing adamantane were designed and synthesized from 1-adamantanecarboxylic acid.The structures of target surfactants were confirmed by 1H NMR,elements analysis and FTIR.Surface properties of these surfactants were investigated.Due to the lipophilicity of adamantane,the critical micelle concentration (CMC) and C20 values of the synthesized quaternary ammonium surfactants are lower than that of conventional quaternary ammonium surfactants.

  11. Lung surfactant levels are regulated by Ig-Hepta/GPR116 by monitoring surfactant protein D.

    Directory of Open Access Journals (Sweden)

    Taku Fukuzawa

    Full Text Available Lung surfactant is a complex mixture of lipids and proteins, which is secreted from the alveolar type II epithelial cell and coats the surface of alveoli as a thin layer. It plays a crucial role in the prevention of alveolar collapse through its ability to reduce surface tension. Under normal conditions, surfactant homeostasis is maintained by balancing its release and the uptake by the type II cell for recycling and the internalization by alveolar macrophages for degradation. Little is known about how the surfactant pool is monitored and regulated. Here we show, by an analysis of gene-targeted mice exhibiting massive accumulation of surfactant, that Ig-Hepta/GPR116, an orphan receptor, is expressed on the type II cell and sensing the amount of surfactant by monitoring one of its protein components, surfactant protein D, and its deletion results in a pulmonary alveolar proteinosis and emphysema-like pathology. By a coexpression experiment with Sp-D and the extracellular region of Ig-Hepta/GPR116 followed by immunoprecipitation, we identified Sp-D as the ligand of Ig-Hepta/GPR116. Analyses of surfactant metabolism in Ig-Hepta(+/+ and Ig-Hepta(-/- mice by using radioactive tracers indicated that the Ig-Hepta/GPR116 signaling system exerts attenuating effects on (i balanced synthesis of surfactant lipids and proteins and (ii surfactant secretion, and (iii a stimulating effect on recycling (uptake in response to elevated levels of Sp-D in alveolar space.

  12. Lung surfactant levels are regulated by Ig-Hepta/GPR116 by monitoring surfactant protein D.

    Science.gov (United States)

    Fukuzawa, Taku; Ishida, Junji; Kato, Akira; Ichinose, Taro; Ariestanti, Donna Maretta; Takahashi, Tomoya; Ito, Kunitoshi; Abe, Jumpei; Suzuki, Tomohiro; Wakana, Shigeharu; Fukamizu, Akiyoshi; Nakamura, Nobuhiro; Hirose, Shigehisa

    2013-01-01

    Lung surfactant is a complex mixture of lipids and proteins, which is secreted from the alveolar type II epithelial cell and coats the surface of alveoli as a thin layer. It plays a crucial role in the prevention of alveolar collapse through its ability to reduce surface tension. Under normal conditions, surfactant homeostasis is maintained by balancing its release and the uptake by the type II cell for recycling and the internalization by alveolar macrophages for degradation. Little is known about how the surfactant pool is monitored and regulated. Here we show, by an analysis of gene-targeted mice exhibiting massive accumulation of surfactant, that Ig-Hepta/GPR116, an orphan receptor, is expressed on the type II cell and sensing the amount of surfactant by monitoring one of its protein components, surfactant protein D, and its deletion results in a pulmonary alveolar proteinosis and emphysema-like pathology. By a coexpression experiment with Sp-D and the extracellular region of Ig-Hepta/GPR116 followed by immunoprecipitation, we identified Sp-D as the ligand of Ig-Hepta/GPR116. Analyses of surfactant metabolism in Ig-Hepta(+/+) and Ig-Hepta(-/-) mice by using radioactive tracers indicated that the Ig-Hepta/GPR116 signaling system exerts attenuating effects on (i) balanced synthesis of surfactant lipids and proteins and (ii) surfactant secretion, and (iii) a stimulating effect on recycling (uptake) in response to elevated levels of Sp-D in alveolar space.

  13. Molecular-thermodynamic theory of micellization of multicomponent surfactant mixtures: 2. pH-sensitive surfactants.

    Science.gov (United States)

    Goldsipe, Arthur; Blankschtein, Daniel

    2007-05-22

    In article 1 of this series, we developed a molecular-thermodynamic (MT) theory to model the micellization of mixtures containing an arbitrary number of conventional (pH-insensitive) surfactants. In this article, we extend the MT theory to model mixtures containing a pH-sensitive surfactant. The MT theory was validated by examining mixtures containing both a pH-sensitive surfactant and a conventional surfactant, which effectively behave like ternary surfactant mixtures. We first compared the predicted micellar titration data to experimental micellar titration data that we obtained for varying compositions of mixed micelles containing the pH-sensitive surfactant dodecyldimethylamine oxide (C12DAO) mixed with either a cationic surfactant (dodecyltrimethylammonium bromide, C12TAB), a nonionic surfactant (dodecyl octa(ethylene oxide), C12E8), or an anionic surfactant (sodium dodecyl sulfate, SDS) surfactant. The MT theory accurately modeled the titration behavior of C12DAO mixed with C12E8. However, C12DAO was observed to interact more favorably with SDS and with C12TAB than was predicted by the MT theory. We also compared predictions to data from the literature for mixtures of C12DAO and SDS. Although the pH values of solutions with no added acid were modeled with only qualitative accuracy, the MT theory resulted in quantitatively accurate predictions of solution pH for mixtures containing added acid. In addition, the predicted degree of counterion binding yielded a lower bound to the experimentally measured value. Finally, we predicted the critical micelle concentration (cmc) of solutions of two pH-sensitive surfactants, tetradecyldimethylamine oxide (C14DAO) and hexadecyldimethyl betaine (C16Bet), at varying solution pH and surfactant composition. However, at the pH values considered, the pH sensitivity of C16Bet could be neglected, and it was equivalently modeled as a zwitterionic surfactant. The cmc's predicted using the MT theory agreed well with the experimental

  14. Effects of Interactions Among Surfactants,Water and Oil on Equilibrium Configuration of Surfactant-Water-Oil Systems

    Institute of Scientific and Technical Information of China (English)

    YUAN Yin-quan; SUN Zhi-bo; XIE Yun; ZOU Xian-wu

    2004-01-01

    The distribution and configuration of surfactants at interface in surfactant-water-oil systems have been investigated using discontinuous molecular dynamic simulations. There exists a certain equilibrium concentration of surfactants at interface for the systems with certain interactions among surfactant, water and oil. The interface length and equilibrium morphology of the systems are dependent on the equilibrium concentration of surfactants at interface and the total amount of surfactants. The interaction strengths among surfactant, water and oil determine the equilibrium concentration of surfactants at interface. Three typical configurations of surfactants at interface have been observed: ① surfactant molecules are perpendicular to the interface and arranged closely; ② perpendicular to the interface and arranged at interval of two particles; ③ lie down in the interface partly.

  15. Aggregation of sulfosuccinate surfactants in water

    Energy Technology Data Exchange (ETDEWEB)

    Magid, L.J.; Daus, K.A.; Butler, P.D.; Quincy, R.B.

    1983-12-22

    The aggregation of sodium di-n-alkyl sulfosuccinates in water (H/sub 2/O and D/sub 2/O at 45/sup 0/C) has been investigated. A self-consistent picture of the dependence of sodium ion binding on surfactant concentration is obtained from emf measurements, conductimetry, and small-angle neutron scattering (SANS) measurements. The concentration dependence of the micellar agregation number for the sulfosuccinates and related double-tailed surfactants depends markedly on surfactant solubility. A sphere-to-disk transition in micellar shape, which might have been expected as a precursor to formation of a lamellar mesophase, was not observed as the surfactant concentration was increased. 8 figures, 2 tables.

  16. Investigation of a polyether trisiloxane surfactant

    OpenAIRE

    Michel, Amandine

    2016-01-01

    Thanks to their adaptability and high efficiency compared to traditional carbon based surfactants, silicone surfactants are a success in many different applications, from pesticides to cosmetics, polyurethane foam, textile and car care products. In spite of those numerous applications, no analytical method existed for their trace determination in environmental samples and no data have been available regarding their environmental occurrence and fate. An analytical method for the trace ana...

  17. Surfactant apoprotein in nonmalignant pulmonary disorders.

    OpenAIRE

    Singh, G.; Katyal, S. L.

    1980-01-01

    Formalin-fixed, paraffin-embedded lungs exhibiting a variety of nonmalignant disorders were studied by immunoperoxidase staining using antibodies specific for surfactant apoprotein, IgG, IgM, IgA, albumin, fibrinogen, and lysozyme. Normal Type II pneumocytes showed staining for surfactant apoprotein in the perinuclear region only. The extent and intensity of staining for apoprotein was markedly increased in reactive Type II pneumocytes. This increase appeared to be a nonspecific reaction to l...

  18. Evaluation of Surfactant Effects on Newborns

    Directory of Open Access Journals (Sweden)

    N. Khalessi

    2006-10-01

    Full Text Available Introduction & Objective: One of the standard therapies in neonates with severe respiratory distress syndrome (RDS is surfactant administration in early course of therapy that cause reduction in mortality, pneumothorax and need to mechanical ventilation. In this study that was carried out in Aliasghar Hospital NICU in 1994-1995 & 2001-2002, the goal was to compare two groups of neonates with severe RDS that had been ventilated in the first 24 hours but one group had received surfactant and the other group (7 years ago was deprived of this substance. Materials & Methods: In our study, 36 neonates that received surfactant and 52 neonates with only mechanical ventilation therapy were compared. Data collected and analyzed using SPSS.Results: We found that mortality in patients with surfactant administration was significantly lower compared to the second group who did not receive surfactant. There were not any significant differences in incidences of HIV, pneumothorax, sepsis, and PDA and also course of hospitalization and need to ventilation between two groups. Conclusion: As a result, all of these findings reflect obligatory surfactant administration in sever RDS in NICU under observation of an educated expert.

  19. Nonlinear water waves with soluble surfactant

    Science.gov (United States)

    Lapham, Gary; Dowling, David; Schultz, William

    1998-11-01

    The hydrodynamic effects of surfactants have fascinated scientists for generations. This presentation describes an experimental investigation into the influence of a soluble surfactant on nonlinear capillary-gravity waves in the frequency range from 12 to 20 Hz. Waves were generated in a plexiglass wave tank (254 cm long, 30.5 cm wide, and 18 cm deep) with a triangular plunger wave maker. The tank was filled with carbon- and particulate-filtered water into which the soluble surfactant Triton-X-100® was added in known amounts. Wave slope was measured nonintrusively with a digital camera running at 225 fps by monitoring the position of light beams which passed up through the bottom of the tank, out through the wavy surface, and onto a white screen. Wave slope data were reduced to determine wave damping and the frequency content of the wave train. Both were influenced by the presence of the surfactant. Interestingly, a subharmonic wave occurring at one-sixth the paddle-driving frequency was found only when surfactant was present and the paddle was driven at amplitudes high enough to produce nonlinear waves in clean water. Although the origins of this subharmonic wave remain unclear, it appears to be a genuine manifestation of the combined effects of the surfactant and nonlinearity.

  20. Performance of some surfactants as wetting agents

    Energy Technology Data Exchange (ETDEWEB)

    Shalaby, M.N.; El-Shanny, O.A.A. [Egyptian Petroleum Research Institute (EPRI), Cairo (Egypt). Evaluation and Analysis Dept.

    2005-12-01

    The wetting power of anionic surfactant: sodium dodecyl sulfate (SDS), and nonionic surfactants: polyoxyethelene(14)monolaurate [La(EO){sub 14}] and polyoxyethelene(14)monoeleate [OI(EO){sub 14}] has been studied to determine their performance as wetting agents. The study reveals that the nonionic compound with a long hydrophobic chain exhibits higher wettability than the shorter one when used at very low cocentrations (below CMC) and the reverse is shown with high concentrations (above CMC). the wetting power of the investigated surfactants increases as the CMC values increases. In case of the nonionic compounds and at surfactant concentrations equal their CMC values, OI(EO){sub 14} shows a higher wetting power than La(EO){sub 14} while is possesses a lower HLB value. The anionic surfactant shows an optimum wetting in comparison with the tested nonionic one. The wettability of all the investigated samples increases as the surface tension of their solutions increases to the allowed limit that can be reached in the presence of surfactant. (orig.)

  1. Spinodal Decomposition in Mixtures Containing Surfactants

    Science.gov (United States)

    Melenekvitz, J.

    1998-03-01

    Spinodal decomposition in mixtures containing two immiscible liquids (A and B) plus surfactant was investigated using a recently developed (J. Melenkevitz and S. H. Javadpour, J. Chem. Phys., 107, 623 (1997).) 3-component Ginzburg-Landau model. The time dependent Ginzburg-Landau (TDGL) equations governing the evolution of structure were numerically integrated in 2-dimensions. We found the growth rate of the average domain size, R(t), decreased with increasing surfactant concentration over a wide range of relative amounts of A and B. This can be attributed to the surfactant accumulating at the growing interface between the immiscible liquids, which leads to a reduction in the surface tension. At late times, the growth rate was noticeably altered when thermal fluctuations were added to the numerical simulations. In this case, power law behavior was observed for R(t) at late times, R(t) ~ t^α, with the exponent α decreasing as the amount of surfactant increased. The dynamics at early times were determined by linearizing the TDGL equations about a uniformly mixed state. The growth rate at ealry times was found to be strongly dependent on the model parameters describing the surfactant miscibility in A and B and the surfactant strength. Comparison with recent measurements on SBR / PB mixtures with added PB-SBR diblock copolymer will also be presented.

  2. DILUTE SURFACTANT METHODS FOR CARBONATE FORMATIONS

    Energy Technology Data Exchange (ETDEWEB)

    Kishore K. Mohanty

    2005-01-01

    There are many carbonate reservoirs in US (and the world) with light oil and fracture pressure below its minimum miscibility pressure (or reservoir may be naturally fractured). Many carbonate reservoirs are naturally fractured. Waterflooding is effective in fractured reservoirs, if the formation is water-wet. Many fractured carbonate reservoirs, however, are mixed-wet and recoveries with conventional methods are low (less than 10%). Thermal and miscible tertiary recovery techniques are not effective in these reservoirs. Surfactant flooding (or huff-n-puff) is the only hope, yet it was developed for sandstone reservoirs in the past. The goal of this research is to evaluate dilute (hence relatively inexpensive) surfactant methods for carbonate formations and identify conditions under which they can be effective. Imbibition in an originally oil-wet 2D capillary is the fastest in the case of Alf-38 and slowest in the case of DTAB (among the surfactants studied). Force of adhesion studies and contact angle measurements show that greater wettability alteration is possible with these anionic surfactants than the cationic surfactant studied. The water imbibition rate does not increase monotonically with an increase in the surfactant concentration. A numerical model has been developed that fits the rate of imbibition. Plans for the next quarter include conducting simulation and imbibition studies.

  3. Silicone antifoam performance enhancement by nonionic surfactants in potato medium.

    Science.gov (United States)

    Christiano, Steven P; Fey, Kenneth C

    2003-01-01

    The ability of a silicone antifoam to retard foaming in a liquor prepared from potatoes is enhanced by the addition of ethoxylated nonionic surfactants. The enhancement is non-linear for surfactant concentration, with all 12 surfactants tested possessing a concentration at which foam heights strongly diminish, referred to as the surfactant critical antifoaming concentration (SCAFC). SCAFCs vary between surfactants, with lower values indicating better mass efficiency of antifoaming enhancement. SCAFCs decrease with degree of ethoxylation and decrease with the hydrophilic-lipophilic balance for ethoxylated nonionic surfactants. Surfactant addition produces a mixed water-surface layer containing surfactant and surface-active components in the potato medium. Surface tension reduction does not correlate well with antifoam performance enhancement. A model is proposed where surfactant adsorption promotes desorption of surface-active potato medium components from the water surface. At the SCAFC, desorption is not complete, yet the rate of bubble rupture is sufficiently enhanced to provide excellent foam control.

  4. Interactions of organic contaminants with mineral-adsorbed surfactants

    Science.gov (United States)

    Zhu, L.; Chen, B.; Tao, S.; Chiou, C.T.

    2003-01-01

    Sorption of organic contaminants (phenol, p-nitrophenol, and naphthalene) to natural solids (soils and bentonite) with and without myristylpyridinium bromide (MPB) cationic surfactant was studied to provide novel insight to interactions of contaminants with the mineral-adsorbed surfactant. Contaminant sorption coefficients with mineral-adsorbed surfactants, Kss, show a strong dependence on surfactant loading in the solid. At low surfactant levels, the Kss values increased with increasing sorbed surfactant mass, reached a maximum, and then decreased with increasing surfactant loading. The Kss values for contaminants were always higher than respective partition coefficients with surfactant micelles (Kmc) and natural organic matter (Koc). At examined MPB concentrations in water the three organic contaminants showed little solubility enhancement by MPB. At low sorbed-surfactant levels, the resulting mineral-adsorbed surfactant via the cation-exchange process appears to form a thin organic film, which effectively "adsorbs" the contaminants, resulting in very high Kss values. At high surfactant levels, the sorbed surfactant on minerals appears to form a bulklike medium that behaves essentially as a partition phase (rather than an adsorptive surface), with the resulting Kss being significantly decreased and less dependent on the MPB loading. The results provide a reference to the use of surfactants for remediation of contaminated soils/sediments or groundwater in engineered surfactant-enhanced washing.

  5. Non-invasive tumor detection in small animals using novel functional Pluronic nanomicelles conjugated with anti-mesothelin antibody

    Science.gov (United States)

    Ding, Hong; Yong, Ken-Tye; Law, Wing-Chueng; Roy, Indrajit; Hu, Rui; Wu, Fang; Zhao, Weiwei; Huang, Kun; Erogbogbo, Folarin; Bergey, Earl J.; Prasad, Paras N.

    2011-04-01

    In this study QDs were encapsulated in carboxylated PluronicF127 (F127COOH) triblock polymeric micelles and conjugated with anti-mesothelin antibody for the purpose of alleviating potential toxicity, enhancing the stability and improving targeting efficiency of CdTe/ZnS quantum dots (QDs) in tumors. The amphiphilic triblock polymer of F127COOH contains hydrophilic carboxylated poly(ethylene oxide) (PEO) and hydrophobic poly(propylene oxide) (PPO) units. After encapsulating QDs into carboxylated F127 (F127COOH-QD) micelles, the particles were conjugated with anti-mesothelin antibodies to allow targeting of cancerous areas. The size of the monodispersed spherical QD-containing micelles was determined to be ~120 nm by dynamic light scattering (DLS). The critical micelle concentration (CMC) was estimated to be 4.7 × 10-7 M. In an in vitro study, the anti-methoselin antibody conjugated F127COOH (Me-F127COOH-QD) nanomicelles showed negligible cytotoxicity to pancreatic cancer cells (Panc-1). Confocal microscopy demonstrated that the Me-F127COOH-QD nanomicelles were taken up more efficiently by Panc-1cells, due to antibody mediated targeting. An in vivo imaging study showed that Me-F127COOH-QD nanomicelles accumulated at the pancreatic tumor site 15 min after intravenous injection. In addition, the low in vivo toxicity of the nanomicellar formulation was evaluated by pathological assays. These results suggest that anti-mesothein antibody conjugated carboxylated F127 nanomicelles may serve as a promising nanoscale platform for early human pancreatic cancer detection and targeted drug delivery.

  6. Disposition and association of the steric stabilizer Pluronic® F127 in lyotropic liquid crystalline nanostructured particle dispersions.

    Science.gov (United States)

    Tilley, Adam J; Drummond, Calum J; Boyd, Ben J

    2013-02-15

    Liquid crystalline nanostructured particles, such as cubosomes and hexosomes, are most often colloidally stabilised using the tri-block co-polymer Pluronic® F127. Although the effect of F127 on the internal particle nanostructure has been well studied, the associative aspects of F127 with cubosomes and hexosomes are poorly understood. In this study the quantitative association of F127 with phytantriol-based cubosomes and hexosomes was investigated. The amount of free F127 in the dispersions was determined using pressure ultra-filtration. The percentage of F127 associated with the particles plateaued with increasing F127 concentration above the critical aggregation concentration. Hence the free concentration of F127 in the dispersion medium was proposed as a key factor governing association below the CMC, and partitioning of F127 between micelles and particles occurred above the CMC. The association of F127 with the particles was irreversible on dilution. The F127 associated with both the external and internal surfaces of the phytantriol cubosomes. The effects of lipid and F127 concentration, lipid type, dilution of the dispersions and internal nanostructure were also elucidated. A greater amount of F127 was associated with cubosomes comprised of glyceryl monooleate (GMO) than those prepared using phytantriol. Hexosomes prepared using a mixture of phytantriol and vitamin E acetate (vitEA) had a greater amount of F127 associated with them than phytantriol cubosomes. Hexosomes prepared using selachyl alcohol had less F127 associated with them than phytantriol:vitEA-based hexosomes and GMO-based cubosomes. This indicated that both the lipid from which the particles are composed and the particle internal nanostructure have an influence on the association of F127 with lyotropic liquid crystalline nanostructured particles. Copyright © 2012 Elsevier Inc. All rights reserved.

  7. Critical interaction strength for surfactant-induced mesomorphic structures in polymer-surfactant systems

    NARCIS (Netherlands)

    Ruokolainen, J.; Torkkeli, M.; Serimaa, R.; Vahvaselka, S.; Saariaho, M.; ten Brinke, G.; Ikkala, O.; Vahvaselkä, Sakari

    1996-01-01

    The critical interaction strength to induce mesomorphic structures in flexible polymers by complexing with surfactants is determined by using surfactants with different hydrogen-bonding strengths;. Two essential requirements have to be satisfied: (i) the association has to be strong enough, otherwis

  8. Surfactant nebulization versus instillation during high frequency ventilation in surfactant-deficient rabbits

    NARCIS (Netherlands)

    Dijk, Peter H.; Heikamp, A; Bambang Oetomo, Sidarto

    1998-01-01

    Surfactant nebulization improves lung function at low alveolar doses of surfactant. However, efficiency of nebulization is low, and lung deposition seems to depend on lung aeration. High frequency ventilation (HFV) has been shown to improve lung aeration. We hypothesize that the combination of HFV a

  9. Surfactant Enhanced Electroremediation of Phenanthrene

    Institute of Scientific and Technical Information of China (English)

    佘鹏; 杨建刚; 等

    2003-01-01

    Removal of hydrophobic organic contaminants(HOCs) form soil of low permeability by electroremediation was investigated by using phenanthrene and kaolinite as a model system.Tween 80 was added into the purging solution in order to enhance the solubility of phenanthrene.The effects of pH on the adsorption of phenanthrene and Tween 80 on kaolinite and the magnitude of ζ-potential of kaolinite were examined,respectively.The effects of electric field strength indicated by electric current on the electroremediation behavior,including the pH of purging solution,the conductivity,phenanthrene concentration and flow rate of effluent,were experimentally investigated,repectively,In case of an electric field of 25mA applied for 72 hours,over 90% of phenanthrene was removed from 424g(dry mass)of kaolinite at an energy consumption of 0.148kW.h.The experimental results described in present study show that the addition of surfactant into purging solution greatly enhances the removel of HOCs by electroremediation.

  10. Biotin-targeted Pluronic(®) P123/F127 mixed micelles delivering niclosamide: A repositioning strategy to treat drug-resistant lung cancer cells.

    Science.gov (United States)

    Russo, Annapina; Pellosi, Diogo Silva; Pagliara, Valentina; Milone, Maria Rita; Pucci, Biagio; Caetano, Wilker; Hioka, Noboru; Budillon, Alfredo; Ungaro, Francesca; Russo, Giulia; Quaglia, Fabiana

    2016-09-10

    With the aim to develop alternative therapeutic tools for the treatment of resistant cancers, here we propose targeted Pluronic(®) P123/F127 mixed micelles (PMM) delivering niclosamide (NCL) as a repositioning strategy to treat multidrug resistant non-small lung cancer cell lines. To build multifunctional PMM for targeting and imaging, Pluronic(®) F127 was conjugated with biotin, while Pluronic(®) P123 was fluorescently tagged with rhodamine B, in both cases at one of the two hydroxyl end groups. This design intended to avoid any interference of rhodamine B on biotin exposition on PMM surface, which is a key fundamental for cell trafficking studies. Biotin-decorated PMM were internalized more efficiently than non-targeted PMM in A549 lung cancer cells, while very low internalization was found in NHI3T3 normal fibroblasts. Biotin-decorated PMM entrapped NCL with good efficiency, displayed sustained drug release in protein-rich media and improved cytotoxicity in A549 cells as compared to free NCL (P<0.01). To go in depth into the actual therapeutic potential of NCL-loaded PMM, a cisplatin-resistant A549 lung cancer cell line (CPr-A549) was developed and its multidrug resistance tested against common chemotherapeutics. Free NCL was able to overcome chemoresistance showing cytotoxic effects in this cell line ascribable to nucleolar stress, which was associated to a significant increase of the ribosomal protein rpL3 and consequent up-regulation of p21. It is noteworthy that biotin-decorated PMM carrying NCL at low doses demonstrated a significantly higher cytotoxicity than free NCL in CPr-A549. These results point at NCL-based regimen with targeted PMM as a possible second-line chemotherapy for lung cancer showing cisplatin or multidrug resistance.

  11. Dilute Surfactant Methods for Carbonate Formations

    Energy Technology Data Exchange (ETDEWEB)

    Kishore K. Mohanty

    2006-02-01

    There are many fractured carbonate reservoirs in US (and the world) with light oil. Waterflooding is effective in fractured reservoirs, if the formation is water-wet. Many fractured carbonate reservoirs, however, are mixed-wet and recoveries with conventional methods are low (less than 10%). The process of using dilute anionic surfactants in alkaline solutions has been investigated in this work for oil recovery from fractured oil-wet carbonate reservoirs both experimentally and numerically. This process is a surfactant-aided gravity drainage where surfactant diffuses into the matrix, lowers IFT and contact angle, which decrease capillary pressure and increase oil relative permeability enabling gravity to drain the oil up. Anionic surfactants have been identified which at dilute concentration of 0.05 wt% and optimal salinity can lower the interfacial tension and change the wettability of the calcite surface to intermediate/water-wet condition as well or better than the cationic surfactant DTAB with a West Texas crude oil. The force of adhesion in AFM of oil-wet regions changes after anionic surfactant treatment to values similar to those of water-wet regions. The AFM topography images showed that the oil-wetting material was removed from the surface by the anionic surfactant treatment. Adsorption studies indicate that the extent of adsorption for anionic surfactants on calcite minerals decreases with increase in pH and with decrease in salinity. Surfactant adsorption can be minimized in the presence of Na{sub 2}CO{sub 3}. Laboratory-scale surfactant brine imbibition experiments give high oil recovery (20-42% OOIP in 50 days; up to 60% in 200 days) for initially oil-wet cores through wettability alteration and IFT reduction. Small (<10%) initial gas saturation does not affect significantly the rate of oil recovery in the imbibition process, but larger gas saturation decreases the oil recovery rate. As the core permeability decreases, the rate of oil recovery reduces

  12. Microemulsion-based lycopene extraction: Effect of surfactants, co-surfactants and pretreatments.

    Science.gov (United States)

    Amiri-Rigi, Atefeh; Abbasi, Soleiman

    2016-04-15

    Lycopene is a potent antioxidant that has received extensive attention recently. Due to the challenges encountered with current methods of lycopene extraction using hazardous solvents, industry calls for a greener, safer and more efficient process. The main purpose of present study was application of microemulsion technique to extract lycopene from tomato pomace. In this respect, the effect of eight different surfactants, four different co-surfactants, and ultrasound and enzyme pretreatments on lycopene extraction efficiency was examined. Experimental results revealed that application of combined ultrasound and enzyme pretreatments, saponin as a natural surfactant, and glycerol as a co-surfactant, in the bicontinuous region of microemulsion was the optimal experimental conditions resulting in a microemulsion containing 409.68±0.68 μg/glycopene. The high lycopene concentration achieved, indicates that microemulsion technique, using a low-cost natural surfactant could be promising for a simple and safe separation of lycopene from tomato pomace and possibly from tomato industrial wastes.

  13. Selection of surfactant in remediation of DDT-contaminated soil by comparison of surfactant effectiveness.

    Science.gov (United States)

    Guo, Ping; Chen, Weiwei; Li, Yueming; Chen, Tao; Li, Linhui; Wang, Guanzhu

    2014-01-01

    With an aim to select the most appropriate surfactant for remediation of DDT-contaminated soil, the performance of nonionic surfactants Tween80, TX-100, and Brij35 and one anionic surfactant sodium dodecyl benzene sulfonate (SDBS) in enhancement of DDT water solubility and desorption of DDT from contaminated soil and their adsorption onto soil and ecotoxicities were investigated in this study. Tween80 had the highest solubilizing and soil-washing ability for DDT among the four experimental surfactants. The adsorption loss of surfactants onto soil followed the order of TX-100 > Tween80 > Brij35 > SDBS. The ecotoxicity of Tween80 to ryegrass (Lolium perenne L.) was lowest. The overall performance considering about the above four aspects suggested that Tween80 should be selected for the remediation of DDT-contaminated soil, because Tween80 had the greatest solubilizing and soil-washing ability for DDT, less adsorption loss onto soil, and the lowest ecotoxicity in this experiment.

  14. The effect of polymeric additives on the solubilisation of a poorly-soluble drug in micellar solutions of Pluronic F127.

    Science.gov (United States)

    Oliveira, Cristiane P; Vasconcellos, Luiz C G; Ribeiro, Maria Elenir N P; Ricardo, Nágila M P S; Souza, Ticiane V de P; Costa, Flávia de M L L; Chaibundit, Chiraphon; Yeates, Stephen G; Attwood, David

    2011-05-16

    The solubilisation of griseofulvin in 1wt% aqueous micellar solutions of Pluronic F127 at 37°C has been modified by adding polyethylene glycol PEG 35000 or poly(vinylpyrrolidone) PVP K30. The solubilisation capacity expressed in terms of unit weight of F127 is increased by the addition of 0.5wt% PEG 35000 to a value approaching double that of a 2.5wt% solution of F127 alone, but there is no advantage in adding 0.5wt% PVP K30.

  15. Effects of PEO-PPO diblock impurities on the cubic structure of aqueous PEO-PPO-PEO pluronics micelles: fcc and bcc ordered structures in F127

    DEFF Research Database (Denmark)

    Mortensen, Kell; Pedersen, Walther Batsberg; Hvidt, S.

    2008-01-01

    We report on structural properties of PEO-PPO-PEO type of triblock block copolymers (Pluronics F127) with special emphasis on the effect of diblock PEO-PPO impurities on the ordered gel phase. Commercial F127 polymers contain as received roughly 20% PEO-PPO diblock and 80% PEO-PPO-PEO triblock...... copolymers. Aqueous solutions of F127 copolymers used as received form fee ordered micellar structure. Copolymers depleted with respect to the diblock impurity, resulting in a pure PEO-PPO-PEO triblock copolymer system, form bcc ordered micelles within the major parts of the gel phase. However, close...

  16. Capacitive performance enhancements of RuO2 nanocrystals through manipulation of preferential orientation growth originated from the synergy of Pluronic F127 trapping and annealing

    Science.gov (United States)

    Chen, I.-Li; Chen, Tsan-Yao; Wei, Yu-Chen; Hu, Chi-Chang; Lin, Tsang-Lang

    2014-02-01

    The capacitive performances of RuO2 prepared by oxidation precipitation of Ru precursors (RuCl3.xH2O) surrounded with tri-block co-polymer, Pluronic F127, in aqueous media can be enhanced through manipulating its preferential orientation growth of nanocrystals. From the heterogeneous surface chemistry viewpoints with the support of structure characterizations, such enhancement originates from the preferential orientation growth of the {101} facet due to the adsorption of the highly polarisable, non-ionic ligands of Pluronic F127 on the high surface energy facets on RuO2 nanocrystallites. In this case, the F127-trapped sample with annealing at 300 °C enhances the specific capacitance 1.6-fold in comparison to its counterpart without F127. With the mechanistic insight into the heterogeneous surface crystal growth pathways, our results materialize the development of RuO2 with tuneable capacitive performances. Furthermore, due to the different propagation models of RuO2 with and without F127 trapping, a schematic diagram is proposed to interpret such a unique crystal growth evolution phenomenon.The capacitive performances of RuO2 prepared by oxidation precipitation of Ru precursors (RuCl3.xH2O) surrounded with tri-block co-polymer, Pluronic F127, in aqueous media can be enhanced through manipulating its preferential orientation growth of nanocrystals. From the heterogeneous surface chemistry viewpoints with the support of structure characterizations, such enhancement originates from the preferential orientation growth of the {101} facet due to the adsorption of the highly polarisable, non-ionic ligands of Pluronic F127 on the high surface energy facets on RuO2 nanocrystallites. In this case, the F127-trapped sample with annealing at 300 °C enhances the specific capacitance 1.6-fold in comparison to its counterpart without F127. With the mechanistic insight into the heterogeneous surface crystal growth pathways, our results materialize the development of RuO2 with

  17. Poly(ester amine) Composed of Polyethylenimine and Pluronic Enhance Delivery of Antisense Oligonucleotides In Vitro and in Dystrophic mdx Mice

    OpenAIRE

    Wang, Mingxing; Wu, Bo; Tucker, Jason D; Bollinger, Lauren E; Lu, Peijuan; Lu, Qilong

    2016-01-01

    A series of poly(esteramine)s (PEAs) constructed from low molecular weight polyethyleneimine (LPEI) and Pluronic were evaluated for the delivery of antisense oligonuclotides (AOs), 2′-O-methyl phosphorothioate RNA (2′-OMePS) and phosphorodiamidate morpholino oligomer (PMO) in cell culture and dystrophic mdx mice. Improved exon-skipping efficiency of both 2′-OMePS and PMO was observed in the C2C12E50 cell line with all PEA polymers compared with PEI 25k or LF-2k. The degree of efficiency was f...

  18. A Review on Progress in QSPR Studies for Surfactants

    Directory of Open Access Journals (Sweden)

    Zhengwu Wang

    2010-03-01

    Full Text Available This paper presents a review on recent progress in quantitative structure-property relationship (QSPR studies of surfactants and applications of various molecular descriptors. QSPR studies on critical micelle concentration (cmc and surface tension (γ of surfactants are introduced. Studies on charge distribution in ionic surfactants by quantum chemical calculations and its effects on the structures and properties of the colloids of surfactants are also reviewed. The trends of QSPR studies on cloud point (for nonionic surfactants, biodegradation potential and some other properties of surfactants are evaluated .

  19. The use of surfactant in lung transplantation.

    Science.gov (United States)

    Amital, Anat; Shitrit, David; Raviv, Yael; Saute, Milton; Medalion, Benjamin; Bakal, Llana; Kramer, Mordechai R

    2008-12-15

    Lung transplantation impairs surfactant activity, which may contribute to primary graft dysfunction (PGD). Prompted by studies in animals and a few reports in humans, this study sought to determine if the administration of surfactant during transplantation serves as an effective preventive measure. An open, randomized, controlled prospective design was used. Forty-two patients scheduled for single (n=38) or double (n=4) lung transplantation at a major tertiary medical center were randomly assigned to receive, or not, intraoperative surfactant treatment. In the treated group, bovine surfactant was administered at a dose of 20 mg phospholipids/kg through bronchoscope after the establishment of bronchial anastomosis. The groups were compared for oxygenation (PaO2/FiO2), chest X-ray findings, PGD grade, and outcome. Compared with the untreated group, the patients who received surfactant were characterized by better postoperative oxygenation mean PaO2/FiO2 (418.8+/-123.8 vs. 277.9+/-165 mm Hg, P=0.004), better chest radiograph score, a lower PGD grade (0.66 vs. 1.86, P=0.005), fewer cases of severe PGD (1 patient vs. 12, P<0.05), earlier extubation (by 2.2 hr; 95% CI 1.1-4.3 hr, P=0.027), shorter intensive care unit stay (by 2.3 days; 95% CI 1.47-3.74 days, P=0.001), and better vital capacity at 1 month (61% vs. 50%, P=0.022). One treated and 2 untreated patients died during the first postoperative month. Surfactant instillation during lung transplantation improves oxygenation, prevents PGD, shortens intubation time, and enhances early posttransplantation recovery. Further, larger studies are needed to assess whether surfactant should be used routinely in lung transplantation.

  20. Surfactants and the Mechanics of Respiration

    Science.gov (United States)

    Jbaily, Abdulrahman; Szeri, Andrew J.

    2016-11-01

    Alveoli are small sacs found at the end of terminal bronchioles in human lungs with a mean diameter of 200 μm. A thin layer of fluid (hypophase) coats the inner face of an alveolus and is in contact with the air in the lungs. The thickness of this layer varies among alveoli, but is in the range of 0.1 to 0.5 μm for many portions of the alveolar network. The interfacial tension σ at the air-hypophase interface tends to favor collapse of the alveolus, and resists its expansion during inhalation. Type II alveolar cells synthesize and secrete a mixture of phospholipids and proteins called pulmonary surfactant. These surfactant molecules adsorb to the interface causing σ of water at body temperature is 70 mN/m and falls to an equilibrium value of 25 mN/m when surfactants are present. Also, in a dynamic sense, it is known that σ is reduced to near 0 during exhalation when the surfactant film compresses. In this work, the authors develop a mechanical and transport model of the alveolus to study the effect of surfactants on various aspects of respiration. The model is composed of three principal parts: (i) air movement into and out of the alveolus; (ii) a balance of linear momentum across the two-layered membrane of the alveolus (hypophase and elastic wall); and (iii) a pulmonary surfactant transport problem in the hypophase. The goal is to evaluate the influence of pulmonary surfactant on respiratory mechanics.

  1. Estudos quimiométricos da pheo formulada em pluronics®: ação fotodinâmica Sobre Artemia salina Chemometric studies of pheo formulated in pluronics®: photodynamic action against Artemia salina

    Directory of Open Access Journals (Sweden)

    Adriana Passarella Gerola

    2013-01-01

    Full Text Available The self-aggregation of pheophytin, a possible photosensitizer for Photodynamic Therapy, is solved by formulation in polymeric surfactant as P-123. The photosensitizer incorporation was found to be time dependent, exhibiting two steps: a partition at the micellar interface followed by an incorporation into the micelle core. The photodynamic efficiency of the formulation was tested by the bioassays against Artemia salina. In order to evaluate how the experimental parameters: pheophytin concentration, P-123 percentage and illumination time influenced the death of artemia, the factorial design 2³ was chosen. The illumination time was found to be the main factor contributing to the mortality of artemia.

  2. DEVELOPMENT OF ORAL NIFEDIPINE-LOADED POLYMERIC NANOCAPSULES: PHYSICOCHEMICAL CHARACTERISATION, PHOTOSTABILITY STUDIES, IN VITRO AND IN VIVO EVALUATION

    Directory of Open Access Journals (Sweden)

    Monika Piazzon Tagliari

    2015-07-01

    Full Text Available In this study, nifedipine (NFP-loaded polymeric nanocapsules were prepared and characterised with a view to protect the drug from degradation. Nanocapsule suspensions were prepared using two different surfactants (pluronic F68 and polyvinyl alcohol. Physicochemical stability and in vivoantihypertensive effect were evaluated. The particle size, zeta potential and entrapment efficiency remained constant during a period of 28 days of exposure under light irradiation. A smaller particle size and a higher zeta potential were obtained for the nanocapsules prepared with Pluronic F68 as surfactant. The solid drug and the nanocapsules were submitted to light exposure for 28 days. After this period of time, the percentage of drug remaining in the PF68NFP and PVANFP nanocapsules was 28.1% and 21.3%, respectively. In contrast, the solid drug was completely degraded after 4 days, suggesting that the nanocapsule suspensions promoted significant protection of the drug against light exposure. In addition, in vivo studies were carried out, which demonstrated that the formulations with polyvinyl alcohol exhibited a very rapid onset of action after oral administration in rats and led to faster drug release. The nanoparticles developed can be considered as an alternative for improving NFP stability in liquid formulations.

  3. INTERACTION BETWEEN SURFACTANT AND COLLAGEN

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Interactions of collagen fibres (made from Beef Achilles tendons )with sodium dodecyl sulfate (SDS),sodium dodecylbenzene sulfonate (SDBS),cetylpyridinium bromide(CPB)and Igepal CA-720 were studied.Sorptions isotherms of all ionic surfactants under different reaction conditions were found out.At suitable conditions S-isotherms were obtained,while under isoeletric conditions isotherms were logaritmic.Igepal had no sorption.The interaction of surfactants with collagen is connected with its mass changes. Changes depend on reaction conditions,namely pH and ionic strenght of reaction solution.Degree of swelling(αm)was used for the description of these changes.At pH=3,in absence SDBS and under low ionic strenghts,a high swelling was attained.An addition of SDBS to reaction mixture led to vigerous deswelling and when the bound amount of SDBS reached about 1 mmol.g-1 αm became independent on a futher bound SDBS.With higher ionic strenghts αm was independent on the equilibrium bound amount of SDBS.Under isoeletric conditions changes of αm were markedly smaller than in acid region and had the opposite character.%研究了十二烷基硫酸钠(SDS)、二十烷基苯磺酸钠(SDBS)、溴化十六烷基吡啶翁(CPB)和Igepal CA-720等表面活性剂与胶原(来源于牛跟腱)间的相互作用.发现了不同的反应条件下,上述离子性表面活性剂的吸附等温线,得到了适当条件下的吸附等温线,同时发现在等电条件下等温线呈对数关系,Igepal没有吸附.表面活性剂与胶原的作用情况与其质量的变化是相互关联的,这种变化取决于反应条件,即pH值和反应溶液中的离子强度,胶原的膨胀程度(am)被用来描述这种变化.在pH3.0,无SDBS存在且在低的离子强度下,胶原得到了大的膨胀:加入SDBS将会导致强烈的消肿作用,并且当胶原对SDBS的结合量达到1mmol/g时,am的值将不再随SDBS结合量的进一步增加而变化.在高的离子

  4. History of surfactant up to 1980.

    Science.gov (United States)

    Obladen, Michael

    2005-01-01

    Remarkable insight into disturbed lung mechanics of preterm infants was gained in the 18th and 19th century by the founders of obstetrics and neonatology who not only observed respiratory failure but also designed devices to treat it. Surfactant research followed a splendid and largely logical growth curve. Pathological changes in the immature lung were characterized in Germany by Virchow in 1854 and by Hochheim in 1903. The Swiss physiologist von Neergard fully understood surfactant function in 1929, but his paper was ignored for 25 years. The physical properties of surfactant were recognized in the early 1950s from research on warfare chemicals by Pattle in Britain and by Radford and Clements in the United States. The causal relationship of respiratory distress syndrome (RDS) and surfactant deficiency was established in the USA by Avery and Mead in 1959. The Australian obstetrician Liggins induced lung maturity with glucocorticoids in 1972, but his discovery was not fully believed for another 20 years. A century of basic research was rewarded when Fujiwara introduced surfactant substitution in Japan in 1980 for treatment and prevention of RDS.

  5. Recovering hydrocarbons with surfactants from lignin

    Energy Technology Data Exchange (ETDEWEB)

    Naae, D.G.; Whittington, L.E.; Ledoux, W.A.; Debons, F.E.

    1988-11-29

    This patent describes a method of recovering hydrocarbons from an underground hydrocarbon formation penetrated by at least one injection well and at least one production well, which comprises: injecting into the formation through an injection well a surfactant slug comprising about 0.1% to about 10% by weight of surfactants produced from lignin, the surfactants produced by placing lignin in contact with water, converting the lignin into low molecular weight lignin phenols by reducing the lignin in the presence of a reducing agent of carbon monoxide or hydrogen creating a reduction reaction mixture comprising oil soluble lignin phenols, the reduction occurring at a temperature greater than about 200/sup 0/C and a pressure greater than about 100 psi, recovering the oil soluble lignin phenols from the reduction mixture, and converting the lignin phenols into lignin surfactants by a reaction selected from the group consisting of alkoxylation, sulfonation, sulfation, aklylation, sulfomethylation, and alkoxysulfation; injecting into the formation through the injection well a drive fluid to push the surfactant slug towards a production well; and recovering hydrocarbons at the production well.

  6. Foaming behaviour of polymer-surfactant solutions

    Energy Technology Data Exchange (ETDEWEB)

    Cervantes-MartInez, Alfredo [Departamento de Investigacion en PolImeros y Materiales, Universidad de Sonora, Apartado Postal 130, 83000 Hermosillo, Sonora (Mexico); Maldonado, Amir [Departamento de Fisica, Universidad de Sonora, Apartado Postal 1626, 83000 Hermosillo, Sonora (Mexico)

    2007-06-20

    We study the effect of a non-ionic amphiphilic polymer (PEG-100 stearate also called Myrj 59) on the foaming behaviour of aqueous solutions of an anionic surfactant (sodium dodecyl sulfate or SDS). The SDS concentration was kept fixed while the Myrj 59 concentration was varied. Measurements of foamability, surface tension and electrical conductivity were carried out. The results show two opposite effects depending on the polymer concentration: foamability is higher when the Myrj 59 concentration is low; however, it decreases considerably when the polymer concentration is increased. This behaviour is due to the polymer adsorption at the air/liquid interface at lower polymer concentrations, and to the formation of a polymer-surfactant complex in the bulk at higher concentrations. The results are confirmed by surface tension and electrical conductivity measurements, which are interpreted in terms of the microstructure of the polymer-surfactant solutions. The observed behaviour is due to the amphiphilic nature of the studied polymer. The increased hydrophobicity of Myrj 59, compared to that of water-soluble polymers like PEG or PEO, increases its 'reactivity' towards SDS, i.e. the strength of its interaction with this anionic surfactant. Our results show that hydrophobically modified polymers have potential applications as additives in order to control the foaming properties of surfactant solutions.

  7. Surfactant apoprotein in nonmalignant pulmonary disorders.

    Science.gov (United States)

    Singh, G.; Katyal, S. L.

    1980-01-01

    Formalin-fixed, paraffin-embedded lungs exhibiting a variety of nonmalignant disorders were studied by immunoperoxidase staining using antibodies specific for surfactant apoprotein, IgG, IgM, IgA, albumin, fibrinogen, and lysozyme. Normal Type II pneumocytes showed staining for surfactant apoprotein in the perinuclear region only. The extent and intensity of staining for apoprotein was markedly increased in reactive Type II pneumocytes. This increase appeared to be a nonspecific reaction to lung injury. The intra-alveolar material in pulmonary alveolar proteinosis stained intensely for surfactant apoprotein, indicating that the accumulated proteinaceous material contained pulmonary surfactant. Type II pneumocytes in pulmonary alveolar proteinosis exhibited hyperplasia as well as hypertrophy. The few macrophages in lung affected by pulmonary alveolar proteinosis stained intensely for lysozyme. The excessive intraalveolar accumulation of proteinaceous material in pulmonary alveolar proteinosis may be the result of both an over-production as well as a deficient removal of pulmonary surfactant. Images Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 Figure 7 Figure 8 Figure 9 p[57]-a PMID:7004201

  8. 2-DE using hemi-fluorinated surfactants.

    Science.gov (United States)

    Starita-Geribaldi, Mireille; Thebault, Pascal; Taffin de Givenchy, Elisabeth; Guittard, Frederic; Geribaldi, Serge

    2007-07-01

    The synthesis of hemi-fluorinated zwitterionic surfactants was realized and assessed for 2-DE, a powerful separation method for proteomic analysis. These new fluorinated amidosulfobetaine (FASB-p,m) were compared to their hydrocarbon counterparts amidosulfobetaine (ASB-n) characterized by a hydrophilic polar head, a hydrophobic and lipophilic tail, and an amido group as connector. The tail of these FASB surfactants was in part fluorinated resulting in the modulation of its lipophilicity (or oleophobicity). Their effect on the red blood cell (RBC) membrane showed a specific solubilization depending on the length of the hydrophobic part. A large number of polypeptide spots appeared in the 2-DE patterns by using FASB-p,m. The oleophobic character of these surfactants was confirmed by the fact that Band 3, a highly hydrophobic transmembrane protein, was not solubilized by these fluorinated structures. The corresponding pellet was very rich in Band 3 and could then be solubilized by using a strong detergent such as amidosulfobetaine with an alkyl tail containing 14 carbon atoms (ASB-14). Thus, these hemi-fluorinated surfactants appeared as powerful tools when used at the first step of a two-step solubilization strategy using a hydrocarbon homologous surfactant in the second step.

  9. Surfactant effects on SF6 hydrate formation.

    Science.gov (United States)

    Lee, Bo Ram; Lee, Ju Dong; Lee, Hyun Ju; Ryu, Young Bok; Lee, Man Sig; Kim, Young Seok; Englezos, Peter; Kim, Myung Hyun; Kim, Yang Do

    2009-03-01

    Sulfur hexafluoride (SF(6)) has been widely used in a variety of industrial processes, but it is one of the most potent greenhouse gases. For this reason, it is necessary to separate or collect it from waste gas streams. One separation method is through hydrate crystal formation. In this study, SF(6) hydrate was formed in aqueous surfactant solutions of 0.00, 0.01, 0.05, 0.15 and 0.20 wt% to investigate the effects of surfactants on the hydrate formation rates. Three surfactants, Tween 20 (Tween), sodium dodecyl sulfate (SDS) and linear alkyl benzene sulfonate (LABS), were tested in a semi-batch stirred vessel at the constant temperature and pressures of 276.2 K and 0.78 MPa, respectively. All surfactants showed kinetic promoter behavior for SF(6) hydrate formation. It was also found that SF(6) hydrate formation proceeded in two stages with the second stage being the most rapid. In situ Raman spectroscopy analysis revealed that the increased gas consumption rate with the addition of surfactant was possibly due to the increased gas filling rate in the hydrate cavity.

  10. Syntheses of surfactants from oleochemical epoxides

    Directory of Open Access Journals (Sweden)

    Warwel Siegfried

    2001-01-01

    Full Text Available Sugar-based surfactants were obtained in good yields (up to 100% under mild conditions (70°C, methanol or mixtures of methanol and water by ring-opening of terminal epoxides with aminopolyols, derived from glucose. Reaction of N-methyl glucamine with epoxides from even-numbered C4-C18 alpha-olefins or from terminal unsaturated fatty acid methyl esters leads to linear products, while corresponding reactions with N-dodecyl glucamine or glucamine yield surfactants with different Y-structures. Products obtained by conversion of omega-epoxy fatty acid methyl esters were saponificated with NaOH or hydrolyzed enzymatically to sodium salts or free acids respectively, which are amphoteric surfactants. Studies of the surfactants at different pH-values demonstrate different surface active properties in aqueous solutions. Critical micelle concentrations (c.m.c. in a range between 2 and 500mg/l and surface tensions of 25-40mN/m were measured for several of the synthesized sugar-based surfactants. The ring-opening products are rather poor foamers, whereas some of the corresponding hydrobromides show good foaming properties.

  11. Interaction of Fluorocarbon Containing Hydrophobically Modified Polyelectrolyte with Nonionic Surfactants

    Institute of Scientific and Technical Information of China (English)

    GUO,Jin-Feng(郭金峰); ZHUANG,Dong-Qing(庄东青); ZHOU,Hui(周晖); ZHANG,Yun-Xiang(章云祥)

    2002-01-01

    The interaction of fluorocarbon containing hydrophobically modified polyelectrolyte (FMPAANa) with two kinds of nonionic surfactants (hydrogenated and fluorinated) in a semidilute (0.5 wt% ) aqueous solution had been studied by rheological measurements. Association behavior was found in both systems. The hydrophobic interaction of FMPAANa with fluorinated surfactant (FC171) is much stronger than that with hydrogenated surfactant (NP7.5) at low surfactant concentrations. The interaction is strengthened by surfactants being added for the density of active junctions increased. Whereas distinct phenomena for FC171 and NP7. 5 start to be found as the surfactants added over their respective certain concentration. The interaction of polyelectrolyte with fluorinated surfactant increases dramatical ly while that with hydrogenated surfactant decreases.

  12. Synthesis of mesoporous nano-hydroxyapatite by using zwitterions surfactant

    Science.gov (United States)

    Mesoporous nano-hydroxyapatite (mn-HAP) was successfully synthesized via a novel micelle-templating method using lauryl dimethylaminoacetic acid as zwitterionic surfactant. The systematic use of such a surfactant in combination with microwave energy inputenables the precise contr...

  13. Polyelectrolyte surfactant aggregates and their deposition on macroscopic surfaces

    CERN Document Server

    Voisin, D

    2002-01-01

    Oppositely charged surfactant and polyelectrolyte are present in hair shampoos and conditioners, together with particles (e.g. anti-dandruff agents for scalp) and droplets (e.g. silicone oil for the hair). These are normally formulated at high surfactant concentrations, beyond the flocculation region for the polyelectrolyte concentration used. However, on dilution with water, during application, flocs are formed which carry the particles and droplets to the scalp and hair. The addition of an anionic surfactant to an aqueous solution of cationic polyelectrolyte, at a given concentration, can lead to the formation of polyelectrolyte-surfactant 'particles', in which the surfactant 'binds' to the polyelectrolyte. This occurs from the critical association concentration (CAC), up to the surfactant concentration corresponding to maximum binding. Within this range of surfactant concentrations, the surfactant bound to the polyelectrolyte is thought to associate to form what might be termed 'internal micelles'. Each po...

  14. Fullerene surfactants and their use in polymer solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Jen, Kwan-Yue; Yip, Hin-Lap; Li, Chang-Zhi

    2015-12-15

    Fullerene surfactant compounds useful as interfacial layer in polymer solar cells to enhance solar cell efficiency. Polymer solar cell including a fullerene surfactant-containing interfacial layer intermediate cathode and active layer.

  15. Surfactant studies for bench-scale operation

    Science.gov (United States)

    Hickey, Gregory S.; Sharma, Pramod K.

    1993-01-01

    A phase 2 study has been initiated to investigate surfactant-assisted coal liquefaction, with the objective of quantifying the enhancement in liquid yields and product quality. This report covers the second quarter of work. The major accomplishments were: completion of coal liquefaction autoclave reactor runs with Illinois number 6 coal at processing temperatures of 300, 325, and 350 C, and pressures of 1800 psig; analysis of the filter cake and the filtrate obtained from the treated slurry in each run; and correlation of the coal conversions and the liquid yield quality to the surfactant concentration. An increase in coal conversions and upgrading of the liquid product quality due to surfactant addition was observed for all runs.

  16. Nanotube Dispersions Made With Charged Surfactant

    Science.gov (United States)

    Kuper, Cynthia; Kuzma, Mike

    2006-01-01

    Dispersions (including monodispersions) of nanotubes in water at relatively high concentrations have been formulated as prototypes of reagents for use in making fibers, films, and membranes based on single-walled carbon nanotubes (SWNTs). Other than water, the ingredients of a dispersion of this type include one or more charged surfactant(s) and carbon nanotubes derived from the HiPco(TradeMark) (or equivalent) process. Among reagents known to be made from HiPco(TradeMark)(or equivalent) SWNTs, these are the most concentrated and are expected to be usable in processing of bulk structures and materials. Test data indicate that small bundles of SWNTs and single SWNTs at concentrations up to 1.1 weight percent have been present in water plus surfactant. This development is expected to contribute to the growth of an industry based on applied carbon nanotechnology. There are expected to be commercial applications in aerospace, avionics, sporting goods, automotive products, biotechnology, and medicine.

  17. BIOSYNTHESIS OF SURFACTANTS ON INDUSTRIAL WASTE

    Directory of Open Access Journals (Sweden)

    Pirog T. P.

    2014-10-01

    Full Text Available The literature and own experimental data on the synthesis of microbial surfactants of different chemical nature (rhamnolipids, sophorolipids, manozylerythritollipids, lipopeptides at various waste (vegetable oil and fat, sugar, dairy industry, agriculture, forestry, biodiesel, as well as waste — fried vegetable oils are presented. Most suitable substrates for the synthesis of microbial surfactants are oil containing waste that, unlike, for example, lignocellulose, whey, technical glycerol do not require pre-treatment and purification. Replacing traditional substrates for the biosynthesis of surfactant with industrial waste will help to reduce the cost of technology by several times, dispose of unwanted waste, solve the problem of storage or disposal of large amounts of waste from the food industry, agricultural sector and companies that produce biodiesel, which spent large amount of energy and money for such needs

  18. Natural surfactants used in cosmetics: glycolipids.

    Science.gov (United States)

    Lourith, N; Kanlayavattanakul, M

    2009-08-01

    Cosmetic surfactant performs detergency, wetting, emulsifying, solubilizing, dispersing and foaming effects. Adverse reactions of chemical synthesis surfactant have an effect on environment and humans, particularly severe in long term. Biodegradability, low toxicity and ecological acceptability which are the benefits of naturally derived surfactant that promises cosmetic safety are, therefore, highly on demand. Biosurfactant producible from microorganisms exhibiting potential surface properties suitable for cosmetic applications especially incorporate with their biological activities. Sophorolipids, rhamnolipids and mannosylerythritol lipids are the most widely used glycolipids biosurfactant in cosmetics. Literatures and patents relevant to these three glycolipids reviewed were emphasizing on the cosmetic applications including personal care products presenting the cosmetic efficiency, efficacy and economy benefits of glycolipids biosurfactant.

  19. Characterization of the paclitaxel loaded chitosan graft Pluronic F127 copolymer micelles conjugate with a DNA aptamer targeting HER-2 overexpressing breast cancer cells

    Science.gov (United States)

    Thach Nguyen, Kim; Nguyen, Thu Ha; Do, Dinh Ho; Huan Le, Quang

    2017-03-01

    In this work we report the isolation of DNA aptamer that is specifically bound to a HER-2 overexpressing SK-BR-3 human breast cancer cell line, using SELEX strategy. Paclitaxel (PTX) loaded chitosan graft Pluronic F127 copolymer micelles conjugate with a DNA aptamer was synthesized and its structure was confirmed by TEM image. This binary mixed system consisting of DNA aptamer modified Pluronic F127 and chitosan could enhance PTX loading capacity and increase micelle stability. Morphology images confirmed the existence of PTX micelles, with an average size of approximately 86.22 ± 1.45 nm diameters. Drug release profile showed that the PTX conjugate maintained a sustained PTX release. From in vitro cell experiment it was shown that 89%–93%, 50%–58%, 55%–62%, 24%–28% and 2%–7% of the SK-BR-3, NS-VN-67, LH-VN-48, HT-VN-26 and NV-VN-31, respectively, were dead after 6–48 h. These results demonstrated a novel DNA aptamer-micelle assembly for efficient detection and a system for the delivery of PTX targeting specific HER-2 overexpressing. We have also successfully cultivated cancer tissues of explants from Vietnamese patients on a type I collagen substrate. The NS-VN-67, LH-VN-48, HT-VN-26 and NV-VN-31cell lines were used as cellular model sources for the study of chemotherapy drug in cancer.

  20. Thermo-sensitive injectable hydrogel based on the physical mixing of hyaluronic acid and Pluronic F-127 for sustained NSAID delivery.

    Science.gov (United States)

    Jung, Young-Seok; Park, Wooram; Park, Hyejin; Lee, Deok-Keun; Na, Kun

    2017-01-20

    The aim of this research is the development of a new type of intra-articularly injectable thermo-sensitive hydrogels for the long-term delivery of Piroxicam (PX). The thermo-sensitive hydrogel was prepared by the simple physical mixing of HA and Pluronic F-127 (HP) in aqueous solution. The addition of high-molecular-weight HA not only enhanced the mechanical strength of the hydrogel but also elicited a sustained drug release. This result could be attributed to the high-molecular-weight HA-assisted inter-micellar packing in the hydrogel inner structure. The critical gelation temperature value of HP hydrogel was considerably lower than native Pluronic F-127. To evaluate the bioavailability, pharmacokinetic parameters were analyzed after articular-cavity injection of the HP hydrogel in beagle dogs. The HP hydrogel exhibits both sustained drug release behavior and superior bioavailability in physiological conditions. Thus, we believe that the NSAID PX-loaded HP hydrogel could be a promising hydrogel-based drug delivery platform for the treatment of arthritis.

  1. A Review on Progress in QSPR Studies for Surfactants

    OpenAIRE

    Zhengwu Wang; Xiaoyi Zhang; Jiwei Hu

    2010-01-01

    This paper presents a review on recent progress in quantitative structure-property relationship (QSPR) studies of surfactants and applications of various molecular descriptors. QSPR studies on critical micelle concentration (cmc) and surface tension (γ) of surfactants are introduced. Studies on charge distribution in ionic surfactants by quantum chemical calculations and its effects on the structures and properties of the colloids of surfactants are also reviewed. The trends of QSPR studies o...

  2. Surfactant-Polymer Interaction for Improved Oil Recovery

    Energy Technology Data Exchange (ETDEWEB)

    Gabitto, Jorge; Mohanty, Kishore K.

    2002-01-07

    The goal of this research was to use the interaction between a surfactant and a polymer for efficient displacement of tertiary oil by improving slug integrity, oil solubility in the displacing fluid and mobility control. Surfactant-polymer flooding has been shown to be highly effective in laboratory-scale linear floods. The focus of this proposal is to design an inexpensive surfactant-polymer mixture that can efficiently recover tertiary oil by avoiding surfactant slug degradation and viscous/heterogeneity fingering.

  3. Dynamic Study of Gemini Surfactant and Single-chain Surfactant at Air/Water Interface

    Institute of Scientific and Technical Information of China (English)

    Yi Jian CHEN; Gui Ying XU; Shi Ling YUAN; Hai Ying SUN

    2005-01-01

    Molecular dynamics (MD) simulation are used to study the properties of gemini surfactant of ethyl-α,ω-bis(dodecyldimethylammonium bromide) (C12C2C12) and dodecyltrimethylammonium bromide (DTAB) at the air/water interface, respectively. In the two systems,the surfactant concentrations are both 28 wt. %, and other conditions are also the same. After reaching the thermodynamic equilibrium, the concentration profiles, the radial distributions functions (RDF) and the mean squared displacement (MSD) are investigated. Theresults reveal that the surface activity of C12C2C12 suffactant is higher than DTAB surfactant.

  4. Surfactant therapy in late preterm infants

    Directory of Open Access Journals (Sweden)

    Murat Yurdakök

    2013-06-01

    Full Text Available Late preterm (LPT neonates are at a high risk for respiratory distress soon after birth due to respiratory distress syndrome (RDS, transient tachypnea of the newborn, persistent pulmonary hypertension, and pneumonia along with an increased need for surfactant replacement therapy, continuous positive airway pressure, and ventilator support when compared with the term neonates. In the past, studies on outcomes of infants with respiratory distress have primarily focused on extremely premature infants, leading to a gap in knowledge and understanding of the developmental biology and mechanism of pulmonary diseases in LPT neonates. Surfactant deficiency is the most frequent etiology of RDS in very preterm and moderately preterm infants, while cesarean section and lung infection play major roles in RDS development in LPT infants. The clinical presentation and the response to surfactant therapy in LPT infants may be different than that seen in very preterm infants. Incidence of pneumonia and occurrence of pneumothorax are significantly higher in LPT and term infants. High rates of pneumonia in these infants may result in direct injury to the type II alveolar cells of the lung with decreasing synthesis, release, and processing of surfactant. Increased permeability of the alveolar capillary membrane to both fluid and solutes is known to result in entry of plasma proteins into the alveolar hypophase, further inhibiting the surface properties of surfactant. However, the oxygenation index value do not change dramatically after ventilation or surfactant administration in LPT infants with RDS compared to very preterm infants. These finding may indicate a different pathogenesis of RDS in late preterm and term infants. In conclusion, surfactant therapy may be of significant benefit in LPT infants with serious respiratory failure secondary to a number of insults. However, optimal timing and dose of administration are not so clear in this group. Additional

  5. Influence of surfactant concentration on nanohydroxyapatite growth

    Indian Academy of Sciences (India)

    D Gopi; J Indira; S Nithiya; L Kavitha; U Kamachi Mudali; K Kanimozhi

    2013-10-01

    Nanohydroxyapatite particles with different morphologies were synthesized through a microwave coupled hydrothermal method using CTAB as a template. A successful synthesis of nanosized HAP spheres, rods and fibres is achieved through this method by controlling the concentration of the surfactant. The concentration of the surfactant was tuned in such a way that the desired HAP nanostructures were obtained. The resultant powders were sintered at 900 °C in order to obtain phase pure HAP particles. The results obtained by Fourier transform infrared spectroscopy (FT–IR), X-ray diffraction analysis (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) techniques have substantiated the formation of nanosized HAP spheres and fibres.

  6. Two-dimensional photonic crystal surfactant detection.

    Science.gov (United States)

    Zhang, Jian-Tao; Smith, Natasha; Asher, Sanford A

    2012-08-07

    We developed a novel two-dimensional (2-D) crystalline colloidal array photonic crystal sensing material for the visual detection of amphiphilic molecules in water. A close-packed polystyrene 2-D array monolayer was embedded in a poly(N-isopropylacrylamide) (PNIPAAm)-based hydrogel film. These 2-D photonic crystals placed on a mirror show intense diffraction that enables them to be used for visual determination of analytes. Binding of surfactant molecules attaches ions to the sensor that swells the PNIPAAm-based hydrogel. The resulting increase in particle spacing red shifts the 2-D diffracted light. Incorporation of more hydrophobic monomers increases the sensitivity to surfactants.

  7. VESICLE-SURFACTANT INTERACTIONS - EFFECTS OF ADDED SURFACTANTS ON THE GEL TO LIQUID-CRYSTAL TRANSITION FOR 2 VESICULAR SYSTEMS

    NARCIS (Netherlands)

    Blandamer, M.J; Briggs, B.; Cullis, P.M.; Engberts, J.B.F.N.; Kacperska, A.

    1995-01-01

    Interactions of both cationic and anionic surfactants with vesicles formed by dimethyldioctadecylammonium bromide (DOAB) and by sodium didodecylphosphate (DDP) have been probed using differential scanning microcalorimetry. The scans show that the surfactants are incorporated into the vesicle bilayer

  8. Vesicle-Surfactant Interactions : Effects of Added Surfactants on the Gel to Liquid-crystal Transition for Two Vesicular Systems

    NARCIS (Netherlands)

    Blandamer, Michael J.; Briggs, Barbara; Cullis, Paul M.; Engberts, Jan B.F.N.; Kacperska, Anna

    1995-01-01

    Interactions of both cationic and anionic surfactants with vesicles formed by dimethyldioctadecylammonium bromide (DOAB) and by sodium didodecylphosphate (DDP) have been probed using differential scanning microcalorimetry. The scans show that the surfactants are incorporated into the vesicle bilayer

  9. Synthesis and Properties of Novel Cationic Maleic Diester Polymerizable Surfactants

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Three new cationic polymerizable surfactants are synthesized by the reaction of alkylmaleic hemiester with glycidyltrimethylammonium chloride. Their structures are confirmed by 1H NMR, IR and elements analysis. The values of CMC and gCMC of these surfactants have been measured. One can obtain nearly monodisperse polystyrene latex by emulsion polymerization using the polymerizable surfactant.

  10. Surfactant phosphatidylcholine metabolism in preterm infants studied with stable isotopes

    NARCIS (Netherlands)

    J.E.H. Bunt (Jan Erik)

    2000-01-01

    textabstractAIM OF THE STUDIES 1. To develop and use a novel method to study surfactant metabolism in preterm and older infants. (chapters 3 and 4). 2. To study endogenous surfactant synthesis in relation to prenatal glucocorticosteroids. (chapters 5 and 6). 3. To study the influence of surfactant

  11. Effects of selected surfactants on soil microbial activity

    Science.gov (United States)

    Surfactants (surface-active agents) facilitate and accentuate the emulsifying, dispersing, spreading, and wetting properties of liquids. Surfactants are used in industry to reduce the surface tension of liquid and to solubilize compounds. For agricultural pest management, surfactants are an import...

  12. Secondary oil recovery process. [two separate surfactant slugs

    Energy Technology Data Exchange (ETDEWEB)

    Fallgatter, W.S.

    1969-01-14

    Oil recovery by two separate surfactant slugs is greater than for either one alone. One slug contains a surfactant(s) in either oil or water. The other slug contains surfactant(s) in thickened water. The surfactants are sodium petroleum sulfonate (Promor SS20), polyoxyethylene sorbitan trioleate (Tween 85), lauric acid diethanolamide (Trepoline L), and sodium tridecyl sulfate polyglycol ether (Trepenol S30T). The thickener is carboxymethyl cellulose (Hercules CMC 70-S Medium thickener) or polyvinyl alcohol (Du Pont Elvanol 50-42). Consolidated sandstone cores were flooded with water, followed with Hawes crude, and finally salt water (5 percent sodium chloride) which recovered about 67 percent of the crude. A maximum of 27.5 percent of the residual oil was recovered by surfactant(s) in oil or water followed by fresh water, then surfactant(s) plus thickener in water followed by fresh water. Either surfactant slug may be injected first. Individually, each of the surfactant slugs can recover from about 3 to 11 percent less residual oil than their total recovery when used consecutively.

  13. Surfactant phosphatidylcholine metabolism in preterm infants studied with stable isotopes

    NARCIS (Netherlands)

    J.E.H. Bunt (Jan Erik)

    2000-01-01

    textabstractAIM OF THE STUDIES 1. To develop and use a novel method to study surfactant metabolism in preterm and older infants. (chapters 3 and 4). 2. To study endogenous surfactant synthesis in relation to prenatal glucocorticosteroids. (chapters 5 and 6). 3. To study the influence of surfactant t

  14. On the binding of calcium by micelles composed of carboxy-modified pluronics measured by means of differential potentiometric titration and modelled with a self-consistent-field theory

    NARCIS (Netherlands)

    Lauw, Y.; Leermakers, F.A.M.; Cohen Stuart, M.A.; Pinheiro, J.P.; Custers, J.P.A.; Broeke, van den L.J.P.; Keurentjes, J.T.F.

    2006-01-01

    We perform differential potentiometric titration measurements for the binding of Ca2+ ions to micelles composed of the carboxylic acid end-standing Pluronic P85 block copolymer (i.e., CAE-85 (COOH-(EO)(26)-(PO)(39)-(EO)(26)-COOH)). Two different ion-selective electrodes (ISEs) are used to detect the

  15. Dispersing and Separating Carbon Nanotubes with Novel Surfactant Formulations

    Science.gov (United States)

    2010-08-01

    regions in the outer region of the complex. Following DGU, the buoyant density of the separated SWNTs is measured directly, and the SWNT chirality ...bioimaging, and drug delivery. Results and Discussion DGU-based separations of arc discharge grown SWNTs were performed with Pluronic block...17 Specific Chiralities Using Helical Assemblies of Flavin Mononucleotide. Nature Nanotech. 2008, 3, 356-362. 23. Green, A. A.; Hersam, M. C

  16. Thermodynamics of non-ionic surfactant Triton X-100-cationic surfactants mixtures at the cloud point

    Energy Technology Data Exchange (ETDEWEB)

    Batigoec, Cigdem [Department of Chemistry, Faculty of Sciences, Trakya University, 22030 Edirne (Turkey); Akbas, Halide, E-mail: hakbas34@yahoo.com [Department of Chemistry, Faculty of Sciences, Trakya University, 22030 Edirne (Turkey); Boz, Mesut [Department of Chemistry, Faculty of Sciences, Trakya University, 22030 Edirne (Turkey)

    2011-12-15

    Highlights: > Non-ionic surfactants are used as emulsifier and solubilizate in such as textile, detergent and cosmetic. > Non-ionic surfactants occur phase separation at temperature as named the cloud point in solution. > Dimeric surfactants have attracted increasing attention due to their superior surface activity. > The positive values of {Delta}G{sub cp}{sup 0} indicate that the process proceeds nonspontaneous. - Abstract: This study investigates the effects of gemini and conventional cationic surfactants on the cloud point (CP) of the non-ionic surfactant Triton X-100 (TX-100) in aqueous solutions. Instead of visual observation, a spectrophotometer was used for measurement of the cloud point temperatures. The thermodynamic parameters of these mixtures were calculated at different cationic surfactant concentrations. The gemini surfactants of the alkanediyl-{alpha}-{omega}-bis (alkyldimethylammonium) dibromide type, on the one hand, with different alkyl groups containing m carbon atoms and an ethanediyl spacer, referred to as 'm-2-m' (m = 10, 12, and 16) and, on the other hand, with -C{sub 16} alkyl groups and different spacers containing s carbon atoms, referred to as '16-s-16' (s = 6 and 10) were synthesized, purified and characterized. Additions of the cationic surfactants to the TX-100 solution increased the cloud point temperature of the TX-100 solution. It was accepted that the solubility of non-ionic surfactant containing polyoxyethylene (POE) hydrophilic chain was a maximum at the cloud point so that the thermodynamic parameters were calculated at this temperature. The results showed that the standard Gibbs free energy ({Delta}G{sub cp}{sup 0}), the enthalpy ({Delta}H{sub cp}{sup 0}) and the entropy ({Delta}S{sub cp}{sup 0}) of the clouding phenomenon were found positive in all cases. The standard free energy ({Delta}G{sub cp}{sup 0}) increased with increasing hydrophobic alkyl chain for both gemini and conventional cationic

  17. Molecular dynamics of surfactant protein C

    DEFF Research Database (Denmark)

    Ramírez, Eunice; Santana, Alberto; Cruz, Anthony

    2006-01-01

    Surfactant protein C (SP-C) is a membrane-associated protein essential for normal respiration. It has been found that the alpha-helix form of SP-C can undergo, under certain conditions, a transformation from an alpha-helix to a beta-strand conformation that closely resembles amyloid fibrils, which...

  18. Titration procedure for low ethoxylated nonionic surfactants

    Energy Technology Data Exchange (ETDEWEB)

    Buschmann, N. [Anorganisch-Chemisches Inst., Lehrstuhl fuer Analytische Chemie, Muenster Univ. (Germany); Huelskoetter, F. [Anorganisch-Chemisches Inst., Lehrstuhl fuer Analytische Chemie, Muenster Univ. (Germany)

    1997-01-01

    Highly lipophilic surfactants are frequently used as emulsifiers for preparing oil-in-water emulsions (e.g. coolants lubricants). Typical surfactants used for this purpose are low ethoxylated alcohols and ethoxylated alkylphenols. Due to the low degree of ethoxylation they cannot be analysed by conventional methods. The method described in this article is based on the introduction of an anionic group into the molecule by a derivatization reaction. The reaction product can be determined by conventional titration methods for anionic surfactants without any modification. The use of the new method for other nonionic surfactants like sorbitan esters, (ethoxylated) fatty acid amides or glycerol fatty acid partial esters is also described as well as the sample preparation for coolants lubricants. (orig.) [Deutsch] Lipophile Tenside werden haeufig zur Herstellung von Oel-in-Wasser-Emulsionen verwandt, wie sie beispielsweise in Kuehlschmiermitteln eingesetzt werden. Typische Vertreter dieser Tenside sind niedrig ethoxylierte Fettalkohole und Alkylphenole. Wegen ihres geringen Ethoxylierungsgrades koennen sie mit den konventionellen Methoden nicht analytisch bestimmt werden. Die hier beschriebene Analysenmethode beruht auf der Derivatisierung der Ethoxylate zu entsprechenden anionischen Tensiden (Ethersulfate). Diese koennen ohne weiteres mit den etablierten Titrationsverfahren bestimmt werden. Die Anwendung dieses neuen Verfahrens auf die Bestimmung anderer nichtionischer Tenside - Sorbitanester, (ethoxylierte) Fettsaeureamide und Partialglyceride - wird ebenso beschrieben wie die Probenvorbereitung fuer die Analyse von Kuehlschmiermitteln. (orig.)

  19. Mitoxantrone-Surfactant Interactions: A Physicochemical Overview

    Directory of Open Access Journals (Sweden)

    Mirela Enache

    2016-10-01

    Full Text Available Mitoxantrone is a synthetic anticancer drug used clinically in the treatment of different types of cancer. It was developed as a doxorubicin analogue in a program to find drugs with improved antitumor activity and decreased cardiotoxicity compared with the anthracyclines. As the cell membrane is the first barrier encountered by anticancer drugs before reaching the DNA sites inside the cells and as surfactant micelles are known as simple model systems for biological membranes, the drugs-surfactant interaction has been the subject of great research interest. Further, quantitative understanding of the interactions of drugs with biomimicking structures like surfactant micelles may provide helpful information for the control of physicochemical properties and bioactivities of encapsulated drugs in order to design better delivery systems with possible biomedical applications. The present review describes the physicochemical aspects of the interactions between the anticancer drug mitoxantrone and different surfactants. Mitoxantrone-micelle binding constants, partitions coefficient of the drug between aqueous and micellar phases and the corresponding Gibbs free energy for the above processes, and the probable location of drug molecules in the micelles are discussed.

  20. Photosensitive surfactants: micellization and interaction with DNA.

    Science.gov (United States)

    Zakrevskyy, Yuriy; Roxlau, Julian; Brezesinski, Gerald; Lomadze, Nino; Santer, Svetlana

    2014-01-28

    Recently, photosensitive surfactants have re-attracted considerable attention. It has been shown that their association with oppositely charged biologically important polyelectrolytes, such as DNA or microgels, can be efficiently manipulated simply by light exposure. In this article, we investigate the self-assembly of photosensitive surfactants as well as their interactions with DNA by calorimetric and spectroscopic methods. Critical micelle concentration (CMC), standard micellization enthalpy, entropy, and Gibbs energy were determined in different conditions (ionic strengths and temperatures) for a series of cationic surfactants with an azobenzene group in their tail. It is shown, that aggregation forces of photosensitive units play an important role in the micellization giving the major contribution to the micellization enthalpy. The onset of the aggregation can be traced from shift of the absorption peak position in the UV-visible spectrum. Titration UV-visible spectroscopy is used as an alternative, simple, and sensitive approach to estimate CMC. The titration UV-visible spectroscopy was also employed to investigate interactions (CAC: critical aggregation concentration, precipitation, and colloidal stabilization) in the DNA-surfactant complex.

  1. Porcine lung surfactant protein B gene (SFTPB)

    DEFF Research Database (Denmark)

    Cirera Salicio, Susanna; Fredholm, Merete

    2008-01-01

    The porcine surfactant protein B (SFTPB) is a single copy gene on chromosome 3. Three different cDNAs for the SFTPB have been isolated and sequenced. Nucleotide sequence comparison revealed six nonsynonymous single nucleotide polymorphisms (SNPs), four synonymous SNPs and an in-frame deletion of 69...

  2. Photosensitive surfactants: Micellization and interaction with DNA

    Science.gov (United States)

    Zakrevskyy, Yuriy; Roxlau, Julian; Brezesinski, Gerald; Lomadze, Nino; Santer, Svetlana

    2014-01-01

    Recently, photosensitive surfactants have re-attracted considerable attention. It has been shown that their association with oppositely charged biologically important polyelectrolytes, such as DNA or microgels, can be efficiently manipulated simply by light exposure. In this article, we investigate the self-assembly of photosensitive surfactants as well as their interactions with DNA by calorimetric and spectroscopic methods. Critical micelle concentration (CMC), standard micellization enthalpy, entropy, and Gibbs energy were determined in different conditions (ionic strengths and temperatures) for a series of cationic surfactants with an azobenzene group in their tail. It is shown, that aggregation forces of photosensitive units play an important role in the micellization giving the major contribution to the micellization enthalpy. The onset of the aggregation can be traced from shift of the absorption peak position in the UV-visible spectrum. Titration UV-visible spectroscopy is used as an alternative, simple, and sensitive approach to estimate CMC. The titration UV-visible spectroscopy was also employed to investigate interactions (CAC: critical aggregation concentration, precipitation, and colloidal stabilization) in the DNA-surfactant complex.

  3. Surfactant protein D is proatherogenic in mice

    DEFF Research Database (Denmark)

    Sørensen, Grith Lykke; Madsen, Jens; Kejling, Karin

    2006-01-01

    Surfactant protein D (SP-D) is an important innate immune defense molecule that mediates clearance of pathogens and modulates the inflammatory response. Moreover, SP-D is involved in lipid homeostasis, and pulmonary accumulation of phospholipids has previously been observed in SP-D-deficient (Spd...

  4. Topological transformation of a surfactant bilayer

    DEFF Research Database (Denmark)

    Le, T.D.; Olsson, U.; Mortensen, K.

    2000-01-01

    Surfactant lamellar phases are often complicated by the formation of multilamellar (onions) under shear, which can originate simply by shaking the sample. A systematic study has been performed on the C10E3-D2O system in which different bilayer structures under a steady shear flow were investigated...

  5. Physicochemical characteristics of PFC surfactants for dry decontamination

    Energy Technology Data Exchange (ETDEWEB)

    Oh, Won Jin; Lee, Chi Woo [Korea University, Seoul (Korea)

    2001-04-01

    Even the trace amount of the used nuclear fuels of high radioactivity are hazardous to the earth and humans. Perfluorocarbons and perfluorocarbon surfactants are emerging to be efficient chemicals in the dry decontamination process of the used fuels of high radioactivity. The theme was undertaken to increase the knowledge on perfluorocarbon surfactants to develop the perfluorocarbon system in the dry decontamination process in Korea. Several cationic and anionic pfc surfactants were synthesized. Effects of pfc surfactants on electrochemical etching of silicon were investigated to form porous silicons. Forces were measured between silicon surfaces and AFM tip in the absence and presence of pfc surfactants. 7 refs., 10 figs. (Author)

  6. Thermally stable surfactants and compositions and methods of use thereof

    Energy Technology Data Exchange (ETDEWEB)

    Chaiko, David J. (Woodridge, IL)

    2008-09-02

    There are provided novel thermally stable surfactants for use with fillers in the preparation of polymer composites and nanocomposites. Typically, surfactants of the invention are urethanes, ureas or esters of thiocarbamic acid having a hydrocarbyl group of from 10 to 50 carbons and optionally including an ionizable or charged group (e.g., carboxyl group or quaternary amine). Thus, there are provided surfactants having Formula I: ##STR00001## wherein the variables are as defined herein. Further provided are methods of making thermally stable surfactants and compositions, including composites and nanocomposites, using fillers coated with the surfactants.

  7. Minimally Invasive Surfactant Therapy and Noninvasive Respiratory Support.

    Science.gov (United States)

    Kribs, Angela

    2016-12-01

    Respiratory distress syndrome (RDS) caused by surfactant deficiency is major cause for neonatal mortality and short- and long-term morbidity of preterm infants. Continuous positive airway pressure and other modes of noninvasive respiratory support and intubation and positive pressure ventilation with surfactant therapy are efficient therapies for RDS. Because continuous positive airway pressure can fail in severe surfactant deficiency, and because traditional surfactant therapy requires intubation and positive pressure ventilation, this entails a risk of lung injury. Several strategies to combine noninvasive respiratory therapy with minimally invasive surfactant therapy have been described. Available data suggest that those strategies may improve outcome of premature infants with RDS.

  8. Structural study of surfactant-dependent interaction with protein

    Energy Technology Data Exchange (ETDEWEB)

    Mehan, Sumit; Aswal, Vinod K., E-mail: vkaswal@barc.gov.in [Solid State Physics Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India); Kohlbrecher, Joachim [Laboratory for Neutron Scattering, Paul Scherrer Institut, CH-5232 PSI Villigen (Switzerland)

    2015-06-24

    Small-angle neutron scattering (SANS) has been used to study the complex structure of anionic BSA protein with three different (cationic DTAB, anionic SDS and non-ionic C12E10) surfactants. These systems form very different surfactant-dependent complexes. We show that the structure of protein-surfactant complex is initiated by the site-specific electrostatic interaction between the components, followed by the hydrophobic interaction at high surfactant concentrations. It is also found that hydrophobic interaction is preferred over the electrostatic interaction in deciding the resultant structure of protein-surfactant complexes.

  9. Palm oil based surfactant products for petroleum industry

    Science.gov (United States)

    Permadi, P.; Fitria, R.; Hambali, E.

    2017-05-01

    In petroleum production process, many problems causing reduced production are found. These include limited oil recovery, wax deposit, asphaltene deposit, sludge deposit, and emulsion problem. Petroleum-based surfactant has been used to overcome these problems. Therefore, innovation to solve these problems using surfactant containing natural materials deserves to be developed. Palm oil-based surfactant is one of the potential alternatives for this. Various types of derivative products of palm oil-based surfactant have been developed by SBRC IPB to be used in handling problems including surfactant flooding, well stimulation, asphaltene dissolver, well cleaning, and wax removal found in oil and gas industry.

  10. Surfactant Sensors in Biotechnology; Part 1 – Electrochemical Sensors

    Directory of Open Access Journals (Sweden)

    Milan Sak-Bosnar

    2004-01-01

    Full Text Available An overview on electrochemical surfactant sensors is given with special attention to papers published since 1993. The importance of surfactants in modern biotechnology is stressed out. Electrochemical sensors are usually divided according to the measured physical quantity to potentiometric, amperometric, conductometric and impedimetric surfactant sensors. The last ones are very few. Potentiometric surfactant sensors are the most numerous due to their simplicity and versatility. They can be used either as end-point titration sensors or as direct EMF measurement sensors, in batch or flow-through mode. Some amperometric surfactant sensors are true biosensors that use microorganisms or living cells.

  11. Dimeric Surfactants: Promising Ingredients of Cosmetics and Toiletries

    Directory of Open Access Journals (Sweden)

    Naveen Kumar

    2013-11-01

    Full Text Available Surfactants are an essential ingredient for cosmetic, toiletries and personal care products for enhancing their performance. Dimeric surfactants demonstrate superiority compared to conventional surfactants in all areas of application. Dimeric surfactants are extremely promising for utilization in various cosmetic formulations viz. shampoo, lotions, creams, conditioners etc. These surfactants possess extremely unique surface properties viz. lower surface tension, unique micellization, low critical micelle concentration (CMC and antimicrobial activity, higher solubilization etc. Dimerics enhance the performances of cosmetics in an extraordinary manner and provide eco-friendly preparations for human epidermis.

  12. Phase diagrams of DNA-photosensitive surfactant complexes: effect of ionic strength and surfactant structure.

    Science.gov (United States)

    Zakrevskyy, Yuriy; Titov, Evgenii; Lomadze, Nino; Santer, Svetlana

    2014-10-28

    Realization of all-optically controlled and efficient DNA compaction is the major motivation in the study of interactions between DNA and photosensitive surfactants. In this article, using recently published approach of phase diagram construction [Y. Zakrevskyy, P. Cywinski, M. Cywinska, J. Paasche, N. Lomadze, O. Reich, H.-G. Löhmannsroben, and S. Santer, J. Chem. Phys. 140, 044907 (2014)], a strategy for substantial reduction of compaction agent concentration and simultaneous maintaining the light-induced decompaction efficiency is proposed. The role of ionic strength (NaCl concentration), as a very important environmental parameter, and surfactant structure (spacer length) on the changes of positions of phase transitions is investigated. Increase of ionic strength leads to increase of the surfactant concentration needed to compact DNA molecule. However, elongation of the spacer results to substantial reduction of this concentration. DNA compaction by surfactants with longer tails starts to take place in diluted solutions at charge ratios Z phase diagrams for different DNA-photosensitive surfactant systems allowed explanation and proposal of a strategy to overcome previously reported limitations of the light-induced decompaction for complexes with increasing surfactant hydrophobicity.

  13. Adsorption of surfactants and polymers at interfaces

    Science.gov (United States)

    Rojas, Orlando Jose

    Surface tension and high-resolution laser light scattering experiments were used to investigate the adsorption of isomeric sugar-based surfactants at the air/liquid interface in terms of surfactant surface packing and rheology. Soluble monolayers of submicellar surfactant solutions exhibited a relatively viscous behavior. It was also proved that light scattering of high-frequency thermally-induced capillary waves can be utilized to study surfactant exchange between the surface and the bulk solution. Such analysis revealed the existence of a diffusional relaxation mechanism. A procedure based on XPS was developed for quantification, on an absolute basis, of polymer adsorption on mica and Langmuir-Blodgett cellulose films. The adsorption of cationic polyelectrolytes on negatively-charged solid surfaces was highly dependent on the polymer ionicity. It was found that the adsorption process is driven by electrostatic mechanisms. Charge overcompensation (or charge reversal) of mica occurred after adsorption of polyelectrolytes of ca. 50% charge density, or higher. It was demonstrated that low-charge-density polyelectrolytes adsorb on solid surfaces with an extended configuration dominated by loops and tails. In this case the extent of adsorption is limited by steric constraints. The conformation of the polyelectrolyte in the adsorbed layer is dramatically affected by the presence of salts or surfactants in aqueous solution. The phenomena which occur upon increasing the ionic strength are consistent with the screening of the electrostatic attraction between polyelectrolyte segments and solid surface. This situation leads to polyelectrolyte desorption accompanied by both an increase in the layer thickness and the range of the steric force. Adsorbed polyelectrolytes and oppositely charged surfactants readily associate at the solid/liquid interface. Such association induces polyelectrolyte desorption at a surfactant concentration which depends on the polyelectrolyte charge

  14. Synthesis and properties evaluation of sulfobetaine surfactant with double hydroxyl

    Science.gov (United States)

    Zhou, Ming; Luo, Gang; Zhang, Ze; Li, Sisi; Wang, Chengwen

    2017-09-01

    A series of sulfobetaine surfactants {N-[(3-alkoxy-2-hydroxyl)propoxy] ethyl-N,N-dimethyl-N-(2-hydroxyl)propyl sulfonate} ammonium chloride were synthesized with raw materials containing linear saturated alcohol, N,N-dimethylethanolamine, sodium 3-chloro-2-hydroxyl propane sulfonic acid and epichlorohydrin. The molecule structures of sulfobetaine surfactants were characterized by FTIR, 1HNMR and elemental analysis. Surface tension measurements can provide us information about the surface tension at the CMC (γCMC), pC20, Γmax and Amin. The pC20 values of sulfobetaine surfactants increase with the hydrophobic chain length increasing. Amin values of the surfactants decrease with increasing hydrophobic chain length from 10 to 14. The critical micelle concentration (CMC) and surface tension (γCMC) values of the sulfobetaine surfactants decrease with increasing hydrophobic chain length from 10 to 16. The lipophilicity of surfactant was enhanced with the increase of the carbon chain, however, the ability of anti-hard water was weakened. The minimum oil/water interfacial tension of four kinds of sulfobetaine surfactants is 10-2-10-3 mN/m magnitude, which indicates that the synthesized bis-hydroxy sulfobetaine surfactants have a great ability to reduce interfacial tension in the surfactant flooding system. The surface tension (γCMC) values of synthesized surfactants were lower compared with conventional anionic surfactant sodium dodecyl sulfonate.

  15. SURFACTANT BASED ENHANCED OIL RECOVERY AND FOAM MOBILITY CONTROL

    Energy Technology Data Exchange (ETDEWEB)

    George J. Hirasaki; Clarence A. Miller; Gary A. Pope; Richard E. Jackson

    2004-02-01

    Surfactant flooding has the potential to significantly increase recovery over that of conventional waterflooding. The availability of a large number of surfactant structures makes it possible to conduct a systematic study of the relation between surfactant structure and its efficacy for oil recovery. Also, the addition of an alkali such as sodium carbonate makes possible in situ generation of surfactant and significant reduction of surfactant adsorption. In addition to reduction of interfacial tension to ultra-low values, surfactants and alkali can be designed to alter wettability to enhance oil recovery. An alkaline surfactant process is designed to enhance spontaneous imbibition in fractured, oil-wet, carbonate formations. It is able to recover oil from dolomite core samples from which there was no oil recovery when placed in formation brine.

  16. CHARACTERIZATION OF PHASE AND EMULSION BEHAVIOR, SURFACTANT RETENTION, AND OIL RECOVERY FOR NOVEL ALCOHOL ETHOXYCARBOXYLATE SURFACTANTS

    Energy Technology Data Exchange (ETDEWEB)

    Lebone T. Moeti; Ramanathan Sampath

    2001-09-28

    This final technical report describes work performed under DOE Grant No. DE-FG26-97FT97278 during the period October 01, 1997 to August 31, 2001 which covers the total performance period of the project. During this period, detailed information on optimal salinity, temperature, emulsion morphologies, effectiveness for surfactant retention and oil recovery was obtained for an Alcohol Ethoxycarboxylate (AEC) surfactant to evaluate its performance in flooding processes. Tests were conducted on several AEC surfactants and NEODOX (23-4) was identified as the most suitable hybrid surfactant that yielded the best proportion in volume for top, middle, and bottom phases when mixed with oil and water. Following the selection of this surfactant, temperature and salinity scans were performed to identify the optimal salinity and temperature, and the temperature and salinity intervals in which all three phases coexisted. NEODOX 23-4 formed three phases between 4 and 52.5 C. It formed an aqueous rich microemulsion phase at high temperatures and an oleic rich microemulsion phase at low temperatures--a characteristic of the ionic part of the surfactant. The morphology measurement system was set-up successfully at CAU. The best oil/water/surfactant system defined by the above phase work was then studied for emulsion morphologies. Electrical conductivities were measured for middle and bottom phases of the NEODOX 23-4/dodecane/10mM water system and by mixing measured volumes of the middle phase into a fixed volume of the bottom phase and vice versa at room temperature. Electrical conductivity of the mixture decreased as the fraction of volume of the middle phase was increased and vice versa. Also inversion phenomena was observed. These experiments were then repeated for bottom/middle (B/M) and middle/bottom (M/B) conjugate pair phases at 10, 15, 25, 30, 35, 40, and 45 C. Electrical conductivity measurements were then compared with the predictions of the conductivity model developed in

  17. Foaming and foam stability for mixed polymer-surfactant solutions: effects of surfactant type and polymer charge.

    Science.gov (United States)

    Petkova, R; Tcholakova, S; Denkov, N D

    2012-03-20

    Solutions of surfactant-polymer mixtures often exhibit different foaming properties, compared to the solutions of the individual components, due to the strong tendency for formation of polymer-surfactant complexes in the bulk and on the surface of the mixed solutions. A generally shared view in the literature is that electrostatic interactions govern the formation of these complexes, for example between anionic surfactants and cationic polymers. In this study we combine foam tests with model experiments to evaluate and explain the effect of several polymer-surfactant mixtures on the foaminess and foam stability of the respective solutions. Anionic, cationic, and nonionic surfactants (SDS, C(12)TAB, and C(12)EO(23)) were studied to clarify the role of surfactant charge. Highly hydrophilic cationic and nonionic polymers (polyvinylamine and polyvinylformamide, respectivey) were chosen to eliminate the (more trivial) effect of direct hydrophobic interactions between the surfactant tails and the hydrophobic regions on the polymer chains. Our experiments showed clearly that the presence of opposite charges is not a necessary condition for boosting the foaminess and foam stability in the surfactant-polymer mixtures studied. Clear foam boosting (synergistic) effects were observed in the mixtures of cationic surfactant and cationic polymer, cationic surfactant and nonionic polymer, and anionic surfactant and nonionic polymer. The mixtures of anionic surfactant and cationic polymer showed improved foam stability, however, the foaminess was strongly reduced, as compared to the surfactant solutions without polymer. No significant synergistic or antagonistic effects were observed for the mixture of nonionic surfactant (with low critical micelle concentration) and nonionic polymer. The results from the model experiments allowed us to explain the observed trends by the different adsorption dynamics and complex formation pattern in the systems studied.

  18. Application of peptide gemini surfactants as novel solubilization surfactants for photosystems I and II of cyanobacteria.

    Science.gov (United States)

    Koeda, Shuhei; Umezaki, Katsunari; Noji, Tomoyasu; Ikeda, Atsushi; Kawakami, Keisuke; Kondo, Masaharu; Yamamoto, Yasushi; Shen, Jian-Ren; Taga, Keijiro; Dewa, Takehisa; Ito, Shigeru; Nango, Mamoru; Tanaka, Toshiki; Mizuno, Toshihisa

    2013-09-17

    We designed novel peptide gemini surfactants (PG-surfactants), DKDKC12K and DKDKC12D, which can solubilize Photosystem I (PSI) of Thermosynecoccus elongatus and Photosystem II (PSII) of Thermosynecoccus vulcanus in an aqueous buffer solution. To assess the detailed effects of PG-surfactants on the original supramolecular membrane protein complexes and functions of PSI and PSII, we applied the surfactant exchange method to the isolated PSI and PSII. Spectroscopic properties, light-induced electron transfer activity, and dynamic light scattering measurements showed that PSI and PSII could be solubilized not only with retention of the original supramolecular protein complexes and functions but also without forming aggregates. Furthermore, measurement of the lifetime of light-induced charge-separation state in PSI revealed that both surfactants, especially DKDKC12D, displayed slight improvement against thermal denaturation below 60 °C compared with that using β-DDM. This degree of improvement in thermal resistance still seems low, implying that the peptide moieties did not interact directly with membrane protein surfaces. By conjugating an electron mediator such as methyl viologen (MV(2+)) to DKDKC12K (denoted MV-DKDKC12K), we obtained derivatives that can trap the generated reductive electrons from the light-irradiated PSI. After immobilization onto an indium tin oxide electrode, a cathodic photocurrent from the electrode to the PSI/MV-DKDKC12K conjugate was observed in response to the interval of light irradiation. These findings indicate that the PG-surfactants DKDKC12K and DKDKC12D provide not only a new class of solubilization surfactants but also insights into designing other derivatives that confer new functions on PSI and PSII.

  19. Evaluation of the wound healing effect of some Jordanian traditional medicinal plants formulated in Pluronic F127 using mice (Mus musculus).

    Science.gov (United States)

    Khalil, Enam A; Afifi, Fatma U; Al-Hussaini, Maysa

    2007-01-03

    The wound healing effect of the aqueous extracts of Inula viscosa, Ajuga chia, Rubia taenifolia and Parieteria diffusa, and the oil of Laurus nobilis, dispersed in water, were examined. The 10% (w/w) Pluronic F127 (PF127) was added to the applied preparations, in order to modify the aqueous extracts viscosity, and to stabilize the oil dispersion. A full thickness wound was made in the dorsal area of the mice. The wounds were treated with the different preparations with 12h intervals for four times in two successive days. For 16 days, the wounds were visually observed, photographically documented and the wound area was measured. After day 16, the animals were sacrificed and the histology of the wound area was examined. The best wound healing activity was observed with the extract of Inula viscosa, followed by Parieteria diffusa, Laurus nobilis, Ajuga chia and the least active extract was that of Rubia taenifolia.

  20. Physico-chemical properties of meso-tetrakis(p-methoxyphenylporphyrin (TMPP incorporated into pluronicTM p-123 and f-127 polymeric micelles

    Directory of Open Access Journals (Sweden)

    Bruno H. Vilsinski

    2014-01-01

    Full Text Available The physicochemical properties (solubilization, structural organization and stability of meso-tetrakis(p-methoxyphenylporphyrin (TMPP, a promising photosensitizer for photodynamic therapy, solubilized in polymeric micelles of tri-block copolymers PluronicTM P-123 and F-127, were studied. The formulations obtained by the solid dispersion method led to monomerization of TMPP in these copolymers. Solubility studies showed that P-123 solubilizes double the photosensitizer than F-127. The self-aggregation phenomenon was affected by the [TMPP]/[poloxamer] ratio and medium temperature. The decrease in the temperature of these systems promoted the formation of different kinds of TMPP aggregates intrinsically connected with the structural changes occurring in the micelles.

  1. Synthesis of mesoporous NiCo2S4 deposited on reduced graphite oxide assistant by co-polymer Pluronic F127 for high-performance supercapacitor

    Science.gov (United States)

    Qin, Huiya; Yang, Shuo; Zhao, Wenliang; Yang, Zhengchun; Li, Xuan; Li, Huijun; Yao, Pei

    2017-10-01

    Mesoporous NiCo2S4 particles deposited on reduced graphite oxide (RGO) sheets using the co-polymer Pluronic F127 as a structure-directing agent have been successfully prepared as a supercapacitor electrode. The formation of F127 micelles alleviated the aggregation of the RGO sheets and generated NiCo2S4 nanoparticles through hydrophilic affinity of ethylene oxide (EO) ends to produce porous channels during the hydrothermal process. This resulted in a large specific area of the prepared material, and superior electrochemical performance in terms of outstanding rate capability of 85.6% (from 1 A g-1 to 20 A g-1) and cycling stability (92.7% retention after 6500 cycles), features that are crucial for supercapacitors in practical application.

  2. Surfactant Based Enhanced Oil Recovery and Foam Mobility Control

    Energy Technology Data Exchange (ETDEWEB)

    George J. Hirasaki; Clarence A. Miller

    2006-09-09

    Surfactant flooding has the potential to significantly increase recovery over that of conventional waterflooding. The availability of a large number of surfactant structures makes it possible to conduct a systematic study of the relation between surfactant structure and its efficacy for oil recovery. A mixture of two surfactants was found to be particularly effective for application in carbonate formations at low temperature. The mixture is single phase for higher salinity or calcium concentrations than that for either surfactant used alone. This makes it possible to inject the surfactant slug with polymer close to optimal conditions and yet be single phase. A formulation has been designed for a particular field application. It uses partially hydrolyzed polyacrylamide for mobility control. The addition of an alkali such as sodium carbonate makes possible in situ generation of naphthenic soap and significant reduction of synthetic surfactant adsorption. The design of the process to maximize the region of ultra-low IFT takes advantage of the observation that the ratio of soap to synthetic surfactant is a parameter in the conditions for optimal salinity. Even for a fixed ratio of soap to surfactant, the range of salinity for low IFT was wider than that reported for surfactant systems in the literature. Low temperature, forced displacement experiments in dolomite and silica sandpacks demonstrate that greater than 95% recovery of the waterflood remaining oil is possible with 0.2% surfactant concentration, 0.5 PV surfactant slug, with no alcohol. Compositional simulation of the displacement process demonstrates the role of soap/surfactant ratio on passage of the profile through the ultralow IFT region, the importance of a wide salinity range of low IFT, and the importance of the viscosity of the surfactant slug. Mobility control is essential for surfactant EOR. Foam is evaluated to improve the sweep efficiency of surfactant injected into fractured reservoirs as well as a

  3. Influence of triblock copolymer (pluronic F127) on enhancing the physico-chemical properties and photocatalytic response of mesoporous TiO2

    Science.gov (United States)

    Samsudin, Emy Marlina; Hamid, Sharifah Bee Abd; Juan, Joon Ching; Basirun, Wan Jefrey

    2015-11-01

    The utilization of triblock copolymer, pluronic F127 as a structure directing agent for the preparation of TiO2 played an important role in enhancing the photocatalytic degradation rate of atrazine by a factor of 1.7. The mesoporous F127-TiO2 showed significant modification of morphology, particle and crystallite size, and presence of defect energy belt within the catalyst forbidden band as proven via photoluminescence spectra and x-ray photon spectroscopy. Hence the photogenerated carriers have longer lifespan to migrate to the catalyst surface for redox activities. Furtherance, surface reactive {0 0 1} facets proven by the formation of new geometrical single crystal of square and rhombus surfaces in F127-TiO2 facilitates atrazine degradation as well. The increased surface area of F127-TiO2 promotes greater atrazine absorption, thus governs improved interaction between absorbed atrazine molecules and surface generated active radicals as a pre-requisite for good photocatalytic activity. Interestingly, using the same synthesis procedure, it was observed that the addition of pluronic F127 significantly affects anatase crystal structure as opposed to the more thermodynamically stable rutile, generating 61% and 25% of total crystallite size modification for anatase and rutile, respectively. However, there were no changes on the final composition of anatase and rutile crystal structure. In overall, enhancement of the photocatalytic degradation of atrazine is ruled out to the following factors (1) modification of geometrical structures and size, (2) narrowing of band gap due to defect energy belt, (3) longer lifespan of photoexcited charges to the catalyst surface, (4) enhanced surface textural properties and (5) increased exposure of reactive {0 0 1} facets, which were all observed in F127-TiO2.

  4. Pulmonary surfactant adsorption is increased by hyaluronan or polyethylene glycol.

    Science.gov (United States)

    Taeusch, H William; Dybbro, Eric; Lu, Karen W

    2008-04-01

    In acute lung injuries, inactivating agents may interfere with transfer (adsorption) of pulmonary surfactants to the interface between air and the aqueous layer that coats the interior of alveoli. Some ionic and nonionic polymers reduce surfactant inactivation in vitro and in vivo. In this study, we tested directly whether an ionic polymer, hyaluronan, or a nonionic polymer, polyethylene glycol, enhanced adsorption of a surfactant used clinically. We used three different methods of measuring adsorption in vitro: a modified pulsating bubble surfactometer; a King/Clements device; and a spreading trough. In addition we measured the effects of both polymers on surfactant turbidity, using this assay as a nonspecific index of aggregation. We found that both hyaluronan and polyethylene glycol significantly increased the rate and degree of surfactant material adsorbed to the surface in all three assays. Hyaluronan was effective in lower concentrations (20-fold) than polyethylene glycol and, unlike polyethylene glycol, hyaluronan did not increase apparent aggregation of surfactant. Surfactant adsorption in the presence of serum was also enhanced by both polymers regardless of whether hyaluronan or polyethylene glycol was included with serum in the subphase or added to the surfactant applied to the surface. Therefore, endogenous polymers in the alveolar subphase, or exogenous polymers added to surfactant used as therapy, may both be important for reducing inactivation of surfactant that occurs with various lung injuries.

  5. SURFACTANT BASED ENHANCED OIL RECOVERY AND FOAM MOBILITY CONTROL

    Energy Technology Data Exchange (ETDEWEB)

    George J. Hirasaki; Clarence A. Miller; Gary A. Pope; Richard E. Jackson

    2004-07-01

    Surfactant flooding has the potential to significantly increase recovery over that of conventional waterflooding. The availability of a large number of surfactants makes it possible to conduct a systematic study of the relation between surfactant structure and its efficacy for oil recovery. Also, the addition of an alkali such as sodium carbonate makes possible in situ generation of surfactant and significant reduction of surfactant adsorption. In addition to reduction of interfacial tension to ultra-low values, surfactants and alkali can be designed to alter wettability to enhance oil recovery. An alkaline surfactant process is designed to enhance spontaneous imbibition in fractured, oil-wet, carbonate formations. It is able to recover oil from dolomite core samples from which there was no oil recovery when placed in formation brine. Mobility control is essential for surfactant EOR. Foam is evaluted to improve the sweep efficiency of surfactant injected into fractured reservoirs. UTCHEM is a reservoir simulator specially designed for surfactant EOR. A dual-porosity version is demonstrated as a potential scale-up tool for fractured reservoirs.

  6. Modeling of surfactant transport and adsorption in porous media

    Energy Technology Data Exchange (ETDEWEB)

    Chung, F.T.H.

    1991-04-01

    When surfactant solution is flowing in a reservoir formation, surfactants will be diluted by flow dispersion, retained in dead-end pores, adsorbed on rock surfaces, or precipitated due to ion exchange. The loss of surfactant will be detrimental to the performance of gas foam. Information of surfactant concentration profiles in reservoir formations is essential for gas foaming technique development. The major objective of this research is to investigate with mathematical models the transport and dynamic adsorption of surfactants in porous media. The mathematical models have taken into account the convection, dispersion, capacitance, and adsorption effects on concentrations of surfactants. Numerical methods and computer programs have been developed which can be used to match experimental results and to determine the characterization parameters in the models. The models can be included in foam simulation programs to calculate surfactant concentration profiles in porous media. A flow experimental method was developed to measure the effluent surfactant concentration, which will be used to determine the model parameters. Commercial foaming agent Alipal CD-128 was used in this study. Equilibrium adsorption and surfactant precipitation have been tested. Tracer solutions with a nonadsorbing solute such as dextrose and sucrose were used to determine the dispersion parameters for the experimental sandpack; thus, the adsorption of the surfactant in the test sand can be identified with an adequate model. 49 refs., 21 figs.

  7. Next Generation Surfactants for Improved Chemical Flooding Technology

    Energy Technology Data Exchange (ETDEWEB)

    Laura Wesson; Prapas Lohateeraparp; Jeffrey Harwell; Bor-Jier Shiau

    2012-05-31

    The principle objective of this project was to characterize and test current and next generation high performance surfactants for improved chemical flooding technology, focused on reservoirs in the Pennsylvanian-aged (Penn) sands. In order to meet this objective the characteristic curvatures (Cc) of twenty-eight anionic surfactants selected for evaluation for use in chemical flooding formulations were determined. The Cc values ranged from -6.90 to 2.55 with the majority having negative values. Crude oil samples from nine Penn sand reservoirs were analyzed for several properties pertinent to surfactant formulation for EOR application. These properties included equivalent alkane carbon numbers, total acid numbers, and viscosity. The brine samples from these same reservoirs were analyzed for several cations and for total dissolved solids. Surfactant formulations were successfully developed for eight reservoirs by the end of the project period. These formulations were comprised of a tertiary mixture of anionic surfactants. The identities of these surfactants are considered proprietary, but suffice to say the surfactants in each mixture were comprised of varying chemical structures. In addition to the successful development of surfactant formulations for EOR, there were also two successful single-well field tests conducted. There are many aspects that must be considered in the development and implementation of effective surfactant formulations. Taking into account these other aspects, there were four additional studies conducted during this project. These studies focused on the effect of the stability of surfactant formulations in the presence of polymers with an associated examination of polymer rheology, the effect of the presence of iron complexes in the brine on surfactant stability, the potential use of sacrificial agents in order to minimize the loss of surfactant to adsorption, and the effect of electrolytes on surfactant adsorption. In these last four studies

  8. Moving liquid surfactant as a way of assessing the properties of surfactant, liquids and surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Titov, A O; Titov, O P; Titov, M O; Karbainov, A N, E-mail: fibrilla45@mail.ru [RUSSIA. GOU VPO East Siberian State Technological University (Russian Federation)

    2011-04-01

    In the study of surface phenomena of the main and only instrumentally-defined parameters are surface tension and wetting angle, including in the field of nanotechnology. These indicators were introduced more than 200 years ago, and any new inventions in this field was no more. The university developed a new method and device for determining the surface activity. The basis of the method and device is the use of video cameras to record the droplet size and changes on the surface of the liquid layer of known thickness from the impact of drops of surfactant (surfactant). Committed changes are then processed using computer software and calculated parameters, which can be characterized by a surfactant and surface properties, which is fluid and very liquid. Determine the surface tension or contact angle is not necessary. Measures of surface activity using the method and device are: 1. The amount of fluid that can move one kilogram of surfactant. The value of this index varies from tens of nanometers to hundreds of thousands of units. The indicator can be converted to energy units, joules. 2. The amount of fluid confined by a surface per unit time is calculated based on the first indicator, complements the characterization of surfactant and may be an indicator of surface characteristics and fluid. 3. Propagation speed of the capillary and microwaves. This indicator complements the first two.

  9. Hydrogels of sodium alginate in cationic surfactants: Surfactant dependent modulation of encapsulation/release toward Ibuprofen.

    Science.gov (United States)

    Jabeen, Suraya; Chat, Oyais Ahmad; Maswal, Masrat; Ashraf, Uzma; Rather, Ghulam Mohammad; Dar, Aijaz Ahmad

    2015-11-20

    The interaction of cetyltrimethylammoium bromide (CTAB) and its gemini homologue (butanediyl-1,4-bis (dimethylcetylammonium bromide), 16-4-16 with biocompatible polymer sodium alginate (SA) has been investigated in aqueous medium. Addition of K2CO3 influences viscoelastic properties of surfactant impregnated SA via competition between electrostatic and hydrophobic interactions. Viscosity of these polymer-surfactant systems increases with increase in concentration of K2CO3, and a cryogel is formed at about 0.5M K2CO3 concentration. The thermal stability of gel (5% SA+0.5M K2CO3) decreases with increase in surfactant concentration, a minimum is observed with increase in 16-4-16 concentration. The impact of surfactant addition on the alginate structure vis-à-vis its drug loading capability and release thereof was studied using Ibuprofen (IBU) as the model drug. The hydrogel with 16-4-16 exhibits higher IBU encapsulation and faster release in comparison to the one containing CTAB. This higher encapsulation-cum-faster release capability has been related to micelle mediated solubilization and greater porosity of the hydrogel with gemini surfactant.

  10. O/W emulsions stabilised by both low molecular weight surfactants and colloidal particles: The effect of surfactant type and concentration.

    Science.gov (United States)

    Pichot, R; Spyropoulos, F; Norton, I T

    2010-12-01

    The stability against coalescence of O/W emulsions in the presence of both surfactants and colloidal particles was investigated. In particular the effect of the surfactant type and concentration in these emulsifier mixtures on the O/W emulsions' stability was studied. Two types of surfactants were selected; those that have the ability to stabilise O/W emulsions on their own (O/W surfactants) and those that cannot (W/O surfactants). Tween 60 and Sodium Caseinate were selected as the O/W surfactants and lecithin as the W/O surfactant. Oil-in-water emulsions prepared with both particles and any of the three surfactants were stable against coalescence but, depending on the type of surfactant, the behaviour of the systems was found to depend on surfactant concentration. The droplet sizes of emulsions stabilised by mixed emulsifier systems containing low concentrations of O/W surfactants (Tween 60 or Sodium Caseinate) were smaller than those solely stabilised by either the surfactant or particles alone. At intermediate O/W surfactants concentrations, the droplet sizes of the emulsions increased. Further increases in the O/W surfactants' concentration, resulted in the complete removal of particles from the interface with the system now behaving as a surfactant-only stabilised emulsion. The behaviour of emulsions stabilised by emulsifier mixtures containing W/O surfactants was not dependent on the concentration of surfactant: no removal of particles was observed. Copyright © 2010 Elsevier Inc. All rights reserved.

  11. Bending elasticity of charged surfactant layers: the effect of mixing.

    Science.gov (United States)

    Bergström, L Magnus

    2006-08-01

    Expressions have been derived from which the spontaneous curvature (H(0)), bending rigidity (k(c)), and saddle-splay constant (k(c)) of mixed monolayers and bilayers may be calculated from molecular and solution properties as well as experimentally available quantities such as the macroscopic hydrophobic-hydrophilic interfacial tension. Three different cases of binary surfactant mixtures have been treated in detail: (i) mixtures of an ionic and a nonionic surfactant, (ii) mixtures of two oppositely charged surfactants, and (iii) mixtures of two ionic surfactants with identical headgroups but different tail volumes. It is demonstrated that k(c)H(0), k(c), and k(c) for mixtures of surfactants with flexible tails may be subdivided into one contribution that is due to bending properties of an infinitely thin surface as calculated from the Poisson-Boltzmann mean field theory and one contribution appearing as a result of the surfactant film having a finite thickness with the surface of charge located somewhat outside the hydrophobic-hydrophilic interface. As a matter of fact, the picture becomes completely different as finite layer thickness effects are taken into account, and as a result, the spontaneous curvature is extensively lowered whereas the bending rigidity is raised. Furthermore, an additional contribution to k(c) is present for surfactant mixtures but is absent for k(c)H(0) and k(c). This contribution appears as a consequence of the minimization of the free energy with respect to the composition of a surfactant layer that is open in the thermodynamic sense and must always be negative (i.e., k(c) is generally found to be brought down by the process of mixing two or more surfactants). The magnitude of the reduction of k(c) increases with increasing asymmetry between two surfactants with respect to headgroup charge number and tail volume. As a consequence, the bending rigidity assumes the lowest values for layers formed in mixtures of two oppositely charged

  12. Water repellency induced by pulmonary surfactants.

    Science.gov (United States)

    Hills, B A

    1982-04-01

    1. Pure cotton fabric was partially carboxylated to produce a tough, porous, hydrophilic sub-phase to stimulate the epithelial membrane of the alveolar wall from a permeability standpoint. 2. Two of the predominant pulmonary surfactants, dipalmitoyl lecithin (DPL) and dipalmitoyl phosphatidylethanolamine (DPPE), were found to inhibit wetting of this synthetic membrane and of human cutaneous epithelium as manifest by a large contact angle. 3. When treated with DPL at physiological concentrations, the porous synthetic membrane was found to support a head of saline well in excess of systolic pulmonary artery pressure with no penetration and could do so for periods well in excess of 1 hr; untreated control samples allowed almost immediate fluid filtration. 4. Filtration could be initiated in the DPL-treated membranes by wetting the reverse side, confirming that the threshold pressure for fluid penetration was afforded by capillarity and, hence, by water repellency induced by the surfactant. 5. Water repellency induced by the amphoteric surfactants occurring naturally in the lung is discussed as a possible factor contributing to the pressure threshold to be exceeded for alveolar oedema to form. 6. Evidence is reviewed and several advantages discussed for the implied concept of an essentially dry lining to the alveolus with a discontinuous liquid layer largely confined to convex corners which could slowly resolve any oedema by surface forces.

  13. Preparation and evaluation of sulphonamide nonionic surfactants

    Energy Technology Data Exchange (ETDEWEB)

    Ahmed, M. H. M.

    2010-07-01

    Alkyl (octyl, decyl and dodecyl; C{sub 8}, C{sub 1}0 and C{sub 1}2) benzene sulphonyl chloride was used in the preparation of a novel series of nonionic surfactants (IV-VI)a-c, (VII-IX) a-c and (X-XII)a-c. The preparations were completed by reacting each alkyl (C{sub 8}, C{sub 1}0 and C{sub 1}2) benzene sulphonyl chloride with ethanolamine to give (I-III) respectively. The resulting products were reacted separately with ethylene oxide in the presence of different (base KOH, Lewis acid SnCl4 and k10 clay) catalysts to produce different moles of nonionic surfactants (5, 7 and 9) in sequence corresponding to (IV-VI)a-c, (VII-IX) a-c and (X-XII)a-c respectively. The chemical structures of prepared nonionic surfactants were elucidated by IR and 1HNMR spectra. The surface activity, biodegradability and biological activities of the prepared compounds were investigated. The obtained data show that these compounds have good surface and biological activities as well as reasonable biodegradability properties. (Author) 30 refs.

  14. Estimation hydrophilic-lipophilic balance number of surfactants

    Energy Technology Data Exchange (ETDEWEB)

    Pawignya, Harsa, E-mail: harsa-paw@yahoo.co.id [Chemical Engineering Department Diponegoro University (Indonesia); Chemical Engineering Departement University of Pembangunan Nasional Yogyakarta (Indonesia); Prasetyaningrum, Aji, E-mail: ajiprasetyaningrum@gmail.com; Kusworo, Tutuk D.; Pramudono, Bambang, E-mail: Pramudono2004@yahoo.com [Chemical Engineering Department Diponegoro University (Indonesia); Dyartanti, Endah R. [Chemical Engineering Department Diponegoro University (Indonesia); Chemical Enginering Departement Sebelas Maret University (Indonesia)

    2016-02-08

    Any type of surfactant has a hydrophilic-lipophilic balance number (HLB number) of different. There are several methods for determining the HLB number, with ohysical properties of surfactant (solubility cloud point and interfacial tension), CMC methods and by thermodynamics properties (Free energy Gibbs). This paper proposes to determined HLB numbers from interfelation methods. The result of study indicated that the CMC method described by Hair and Moulik espesially for nonionic surfactant. The application of exess Gibbs free energy and by implication activity coefficient provides the ability to predict the behavior of surfactants in multi component mixtures of different concentration. Determination of HLB number by solubility and cloud point parameter is spesific for anionic and nonionic surfactant but this methods not available for cationic surfactants.

  15. Influence of metacide - surfactant complexes on agricultural crops

    Directory of Open Access Journals (Sweden)

    Orynkul Esimova

    2014-12-01

    Full Text Available The complexes based on surfactants and polyhexamethyleneguanidine hydrochloride (metacide are important for agriculture. This paper considers compositions of known bactericidal metacide with different surfactants: anionic surfactant sodium dodecylsulphate (DDSNa and nonionic surfactant Tween 80 (monooleate of oxyethylenated anhydrosorbitols. The effect of individual components and associates of metacide and surfactants on productivity and infection of cereals was studied. According to the study, the highest productivity and infection rate were shown by the associate of metacide and Tween-80. At concentration of Tween-80 in aqueous solution equal to 0.001% in combination with metacide, efficiency was 98% at 0% infection. The surface tension and the wetting of metacide, DDSNa, Tween-80, and associates of metacide with surfactants were studied. In comparison with individual components, metacide-DDSNa and metacide-Tween-80 associates have higher surface activity.

  16. [Pulmonary surfactant homeostasis associated genetic abnormalities and lung diseases].

    Science.gov (United States)

    Jiang, Xiaojing; Sun, Xiuzhu; Du, Weihua; Hao, Haisheng; Zhao, Xueming; Wang, Dong; Zhu, Huabin; Liu, Yan

    2016-08-01

    Pulmonary surfactant (PS) is synthesized and secreted by alveolar epithelial type II (AEII) cells, which is a complex compound formed by proteins and lipids. Surfactant participates in a range of physiological processes such as reducing the surface tension, keeping the balance of alveolar fluid, maintaining normal alveolar morphology and conducting host defense. Genetic disorders of the surfactant homeostasis genes may result in lack of surfactant or cytotoxicity, and lead to multiple lung diseases in neonates, children and adults, including neonatal respiratory distress syndrome, interstitial pneumonia, pulmonary alveolar proteinosis, and pulmonary fibrosis. This paper has provided a review for the functions and processes of pulmonary surfactant metabolism, as well as the connection between disorders of surfactant homeostasis genes and lung diseases.

  17. Branched alkyl alcohol propoxylated sulfate surfactants for improved oil recovery

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Y.; Iglauer, S.; Shuler, P.; Tang, Y. [California Institute of Technology, Covina, CA (US). Power, Environmental and Energy Research (PEER) Center; Goddard, W.A. III [California Institute of Technology, Pasadena, CA (United States). Materials and Process Simulation Center

    2010-05-15

    This investigation considers branched alkyl alcohol propoxylated sulfate surfactants as candidates for chemical enhanced oil recovery (EOR) applications. Results show that these anionic surfactants may be preferred candidates for EOR as they can be effective at creating low interfacial tension (IFT) at dilute concentrations, without requiring an alkaline agent or cosurfactant. In addition, some of the formulations exhibit a low IFT at high salinity, and hence may be suitable for use in more saline reservoirs. Adsorption tests onto kaolinite clay indicate that the loss of these surfactants can be comparable to or greater than other types of anionic surfactants. Surfactant performance was evaluated in oil recovery core flood tests. Selected formulations recovered 35-50% waterflood residual oil even with dilute 0.2 wt% surfactant concentrations from Berea sandstone cores. (orig.)

  18. Rheological properties of ovalbumin hydrogels as affected by surfactants addition.

    Science.gov (United States)

    Hassan, Natalia; Messina, Paula V; Dodero, Veronica I; Ruso, Juan M

    2011-04-01

    The gel properties of ovalbumin mixtures with three different surfactants (sodium perfluorooctanoate, sodium octanoate and sodium dodecanoate) have been studied by rheological techniques. The gel elasticities were determined as a function of surfactant concentration and surfactant type. The fractal dimension of the formed structures was evaluated from plots of storage modulus against surfactant concentration. The role of electrostatic, hydrophobic and disulfide SS interactions in these systems has been demonstrated to be the predominant. The viscosity of these structures tends to increase with surfactant concentration, except for the fluorinated one. Unfolded ovalbumin molecules tend to form fibrillar structures that tend to increase with surfactant concentration, except for the fluorinated one. This fact has been related to the particular nature of this molecule.

  19. Gemini imidazolium surfactants: synthesis and their biophysiochemical study.

    Science.gov (United States)

    Kamboj, Raman; Singh, Sukhprit; Bhadani, Avinash; Kataria, Hardeep; Kaur, Gurcharan

    2012-08-21

    New gemini imidazolium surfactants 9-13 have been synthesized by a regioselective epoxy ring-opening reaction under solvent-free conditions. The surface properties of these new gemini surfactants were evaluated by surface tension and conductivity measurements. These surfactants have been found to have low critical micelle concentration (cmc) values as compared to other categories of gemini cationic surfactants and also showed the tendency to form premicellar aggregates in solution at sufficiently low concentration below their cmc values. The thermal degradation of these surfactants was determined by thermograviometry analysis (TGA). These new cationic surfactants have a good DNA binding capability as determined by agarose gel electrophoresis and ethidium bromide exclusion experiments. They have also been found to have low cytotoxicity by MTT (3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide) assay on the C6 glioma cell line.

  20. Effects of silicon surfactant in rigid polyurethane foams

    Directory of Open Access Journals (Sweden)

    2008-03-01

    Full Text Available The rigid polyurethane foams (RPUFs have been fabricated from high functional crude 4,4’-di-phenylmethane diisocyanate (CMDI and polypropylene glycols (PPGs for a wide range of surfactant concentration with an environmently friendly blowing agent (HFC 365mfc. Cream time, gel time, and tack-free time increased with the addition of surfactant. Foam density decreased rapidly to a minimum at 0.5 pphp (part per hundred polyol surfactant due to the increased blowing efficiency with surfactant. Surface tension rapidly decreased to an asymptotic value at 2 pphp surfactant. In accordance with this, cell size decreased and closed cell content increased rapidly to constant values at low surfactant concentrations (<1 pphp. The decrease of cell size was accompanied by the decrease of thermal conductivity to give a linear relatiohship between the two implying that the series model of heat transfer is applicable.

  1. Interfacial mechanisms for stability of surfactant-laden films

    CERN Document Server

    Bhamla, M Saad; Alvarez-Valenzuela, Marco A; Tajuelo, Javier; Fuller, Gerald G

    2016-01-01

    Thin liquid films are central to everyday life. They are ubiquitous in modern technology (pharmaceuticals, coatings), consumer products (foams, emulsions) and also serve vital biological functions (tear film of the eye, pulmonary surfactants in the lung). A common feature in all these examples is the presence of surface-active molecules at the air-liquid interface. Though they form only molecularly-thin layers, these surfactants produce complex surface stresses on the free surface, which have important consequences for the dynamics and stability of the underlying thin liquid film. Here we conduct simple thinning experiments to explore the fundamental mechanisms that allow the surfactant molecules to slow the gravity-driven drainage of the underlying film. We present a simple model that works for both soluble and insoluble surfactant systems. We show that surfactants with finite surface rheology influence bulk flow through viscoelastic interfacial stresses, while surfactants with inviscid surfaces achieve stab...

  2. Pore Orientation Effects on the Kinetics of Mesostructure Loss in Surfactant Templated Titania Thin Films

    Energy Technology Data Exchange (ETDEWEB)

    Das, Saikat; Nagpure, Suraj R.; Garlapalli, Ravinder Kumar; Wu, Qingliu; Islam, Syed Z.; Strzalka, Joseph; Rankin, Stephen E.

    2016-01-28

    The mesostructure loss kinetics are measured as a function of the orientation of micelles in 2D hexagonal close packed (HCP) columnar mesostructured titania thin films using in situ grazing incidence small angle x-ray scattering (GISAXS). Complementary supporting information is provided by ex situ scanning electron microscopy. Pluronic surfactant P123 acts as the template to synthesize HCP structured titania thin films. When the glass substrates are modified with crosslinked P123, the micelles of the HCP mesophase align orthogonal to the films, whereas a mix of parallel and orthogonal alignment is found on unmodified glass. The rate of mesostructure loss of orthogonally oriented (o-HCP) thin films (~60 nm thickness) prepared on modified substrate is consistently found to be less by a factor of 2.5±0.35 than that measured for mixed orientation HCP films on unmodified substrates. The activation energy for mesostructure loss is only slightly greater for films on modified glass (155±25 kJ/mol) than on unmodified (128 kJ/mol), which implies that the rate difference stems a greater activation entropy for mesostructure loss in o-HCP titania films. Nearly perfect orthogonal orientation of micelles on modified surfaces contributes to the lower rate of mesostructure loss by supporting the anisotropic stresses that develop within the films during annealing due to continuous curing, sintering and crystallization into the anatase phase during high temperature calcination (>450 °C). Because the film thickness dictates the propagation of orientation throughout the films and the degree of confinement, thicker (~250 nm) films cast onto P123-modified substrates have a much lower activation energy for mesostructure loss (89±27 kJ/mol) due to the mix of orientations found in the films. Thus, this kinetic study shows that thin P123- templated o-HCP titania films are not only better able to achieve good orthogonal alignment of 3 the mesophase relative to thicker films or films on

  3. Pore orientation effects on the kinetics of mesostructure loss in surfactant templated titania thin films.

    Science.gov (United States)

    Das, Saikat; Nagpure, Suraj; Garlapalli, Ravinder K; Wu, Qingliu; Islam, Syed Z; Strzalka, Joseph; Rankin, Stephen E

    2016-01-28

    The mesostructure loss kinetics are measured as a function of the orientation of micelles in 2D hexagonal close packed (HCP) columnar mesostructured titania thin films using in situ grazing incidence small angle X-ray scattering (GISAXS). Complementary supporting information is provided by ex situ scanning electron microscopy. Pluronic surfactant P123 acts as the template to synthesize HCP structured titania thin films. When the glass substrates are modified with crosslinked P123, the micelles of the HCP mesophase align orthogonal to the films, whereas a mix of parallel and orthogonal alignment is found on unmodified glass. The rate of mesostructure loss of orthogonally oriented (o-HCP) thin films (∼60 nm thickness) prepared on modified substrate is consistently found to be less by a factor of 2.5 ± 0.35 than that measured for mixed orientation HCP films on unmodified substrates. The activation energy for mesostructure loss is only slightly greater for films on modified glass (155 ± 25 kJ mol(-1)) than on unmodified (128 kJ mol(-1)), which implies that the rate difference stems from a greater activation entropy for mesostructure loss in o-HCP titania films. Nearly perfect orthogonal orientation of micelles on modified surfaces contributes to the lower rate of mesostructure loss by supporting the anisotropic stresses that develop within the films during annealing due to continuous curing, sintering and crystallization into the anatase phase during high temperature calcination (>450 °C). Because the film thickness dictates the propagation of orientation throughout the films and the degree of confinement, thicker (∼250 nm) films cast onto P123-modified substrates have a much lower activation energy for mesostructure loss (89 ± 27 kJ mol(-1)) due to the mix of orientations found in the films. Thus, this kinetic study shows that thin P123-templated o-HCP titania films are not only better able to achieve good orthogonal alignment of the mesophase relative to

  4. Investigation of Polymer-Surfactant and Polymer-Drug-Surfactant Miscibility for Solid Dispersion.

    Science.gov (United States)

    Gumaste, Suhas G; Gupta, Simerdeep Singh; Serajuddin, Abu T M

    2016-09-01

    In a solid dispersion (SD), the drug is generally dispersed either molecularly or in the amorphous state in polymeric carriers, and the addition of a surfactant is often important to ensure drug release from such a system. The objective of this investigation was to screen systematically polymer-surfactant and polymer-drug-surfactant miscibility by using the film casting method. Miscibility of the crystalline solid surfactant, poloxamer 188, with two commonly used amorphous polymeric carriers, Soluplus® and HPMCAS, was first studied. Then, polymer-drug-surfactant miscibility was determined using itraconazole as the model drug, and ternary phase diagrams were constructed. The casted films were examined by DSC, PXRD and polarized light microscopy for any crystallization or phase separation of surfactant, drug or both in freshly prepared films and after exposure to 40°C/75% RH for 7, 14, and 30 days. The miscibility of poloxamer 188 with Soluplus® was <10% w/w, while its miscibility with HPMCAS was at least 30% w/w. Although itraconazole by itself was miscible with Soluplus® up to 40% w/w, the presence of poloxamer drastically reduced its miscibility to <10%. In contrast, poloxamer 188 had minimal impact on HPMCAS-itraconazole miscibility. For example, the phase diagram showed amorphous miscibility of HPMCAS, itraconazole, and poloxamer 188 at 54, 23, and 23% w/w, respectively, even after exposure to 40°C/75% RH for 1 month. Thus, a relatively simple and practical method of screening miscibility of different components and ultimately physical stability of SD is provided. The results also identify the HPMCAS-poloxamer 188 mixture as an optimal surface-active carrier system for SD.

  5. [Liposome phospholipid substitution and lung function in surfactant deprived rats].

    Science.gov (United States)

    Obladen, M

    1985-01-01

    In vivo activity of an artificial surfactant was studied in surfactant depleted rats. After tenfold alveolar lavage, PaO2, tidal volume, and compliance of the respiratory system fell to one third of initial value. Substitution of large unilamellar vesicles containing 90% Dipalmitoylphosphatidylcholine and 10% unsaturated phosphatidylglycerol largely restored oxygenation and lung mechanics in most animals. Complete normalization with weaning from the ventilator, however, was achieved neither with liposomes nor with natural surfactant concentrate.

  6. The Role of Surfactant in Respiratory Distress Syndrome

    OpenAIRE

    2012-01-01

    The key feature of respiratory distress syndrome (RDS) is the insufficient production of surfactant in the lungs of preterm infants. As a result, researchers have looked into the possibility of surfactant replacement therapy as a means of preventing and treating RDS. We sought to identify the role of surfactant in the prevention and management of RDS, comparing the various types, doses, and modes of administration, and the recent development. A PubMed search was carried out up to March 2012 u...

  7. Surfactant Based Enhanced Oil Recovery and Foam Mobility Control

    Energy Technology Data Exchange (ETDEWEB)

    George J. Hirasaki; Clarence A. Miller; Gary A. Pope

    2005-07-01

    Surfactant flooding has the potential to significantly increase recovery over that of conventional waterflooding. The availability of a large number of surfactant structures makes it possible to conduct a systematic study of the relation between surfactant structure and its efficacy for oil recovery. A combination of two surfactants was found to be particularly effective for application in carbonate formations at low temperature. A formulation has been designed for a particular field application. The addition of an alkali such as sodium carbonate makes possible in situ generation of surfactant and significant reduction of surfactant adsorption. In addition to reduction of interfacial tension to ultra-low values, surfactants and alkali can be designed to alter wettability to enhance oil recovery. The design of the process to maximize the region of ultra-low IFT is more challenging since the ratio of soap to synthetic surfactant is a parameter in the conditions for optimal salinity. Compositional simulation of the displacement process demonstrates the interdependence of the various components for oil recovery. An alkaline surfactant process is designed to enhance spontaneous imbibition in fractured, oil-wet, carbonate formations. It is able to recover oil from dolomite core samples from which there was no oil recovery when placed in formation brine. Mobility control is essential for surfactant EOR. Foam is evaluated to improve the sweep efficiency of surfactant injected into fractured reservoirs. UTCHEM is a reservoir simulator specially designed for surfactant EOR. It has been modified to represent the effects of a change in wettability. Simulated case studies demonstrate the effects of wettability.

  8. AARC Clinical Practice Guideline. Surfactant replacement therapy: 2013.

    Science.gov (United States)

    Walsh, Brian K; Daigle, Brandon; DiBlasi, Robert M; Restrepo, Ruben D

    2013-02-01

    We searched the MEDLINE, CINAHL, and Cochrane Library databases for English-language randomized controlled trials, systematic reviews, and articles investigating surfactant replacement therapy published between January 1990 and July 2012. By inspection of titles, references having no relevance to the clinical practice guideline were eliminated. The update of this clinical practice guideline is based on 253 clinical trials and systematic reviews, and 12 articles investigating surfactant replacement therapy. The following recommendations are made following the Grading of Recommendations Assessment, Development, and Evaluation scoring system: 1: Administration of surfactant replacement therapy is strongly recommended in a clinical setting where properly trained personnel and equipment for intubation and resuscitation are readily available. 2: Prophylactic surfactant administration is recommended for neonatal respiratory distress syndrome (RDS) in which surfactant deficiency is suspected. 3: Rescue or therapeutic administration of surfactant after the initiation of mechanical ventilation in infants with clinically confirmed RDS is strongly recommended. 4: A multiple surfactant dose strategy is recommended over a single dose strategy. 5: Natural exogenous surfactant preparations are recommended over laboratory derived synthetic suspensions at this time. 6: We suggest that aerosolized delivery of surfactant not be utilized at this time.

  9. Effects of Surfactant Adsorption on Surficial Wettability of Nonwoven Fabrics

    Institute of Scientific and Technical Information of China (English)

    CAI Bing; TANG Bing; LI Rui-xia; WU Da-cheng

    2002-01-01

    All types of surfactants (cationic, anionic and nonionic)reported in this paper could enhance the surficiai wettability of polypropylene (PP) and polyethylene terephthalate (PET) nonwoven fabrics. However, the effects of cationic and nonionic surfactants were better.The longer the treatment time of surfactants on the nonwoven fabrics, the better the surficial wettability.The surficial rewetting time would no longer change above a certain treatment time. The rewettability of nonwoven fabrics could be evidently improved just when the concentration of surfactants was just above the CMC,except for sodium dodecylbenzene sulfonate (LAS). The finer the fibers and the looser the structures, the better the surficial rewettability of nonwoven fabrics.

  10. Interactions in Calcium Oxalate Hydrate/Surfactant Systems.

    Science.gov (United States)

    Sikiric; Filipovic-Vincekovic; Babic-Ivancić Vdović Füredi-Milhofer

    1999-04-15

    Phase transformation of calcium oxalate dihydrate (COD) into the thermodynamically stable monohydrate (COM) in anionic (sodium dodecyl sulfate (SDS)) and cationic (dodecylammonium chloride) surfactant solutions has been studied. Both surfactants inhibit, but do not stop transformation from COD to COM due to their preferential adsorption at different crystal faces. SDS acts as a stronger transformation inhibitor. The general shape of adsorption isotherms of both surfactants at the solid/liquid interface is of two-plateau-type, but differences in the adsorption behavior exist. They originate from different ionic and molecular structures of crystal surfaces and interactions between surfactant headgroups and solid surface. Copyright 1999 Academic Press.

  11. Effects of Surfactant on Solubility and Microbial Conversion of Steroid

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    Enhancing the dispersion and dissolution of substrate particles in substrate/water suspension is a feasible way to improve steroid bioconversion. The aim of the present study is to investigate the effects of applying surfactant to microbial conversion system on the dispersion, solubilization and in turn bioconversion of steroid substrate. The model system is hydroxylation of substrate 16α-,17α-epoxy-4-pregnene-3,20-dine by microbial enzymes from Rhizopus nigricanl. The results show that the presence of substrate leads to an increase in critical micelle concentration (CMC) of surfactant PSE compared with the normal CMC of PSE in aqueous solution. The grinding time during substrate suspension preparation affects the substrate aqueous solubility differently with the varied surfactant concentrations while barely making any difference in substrate solubility in the absence of surfactant. The properly prolonged grinding time can make up for the loss in substrate solubility arising from the reduction in surfactant concentration. The surfactant complexes composed of surfactants PSE and MGE at appropriate ratios are screened out with orthodoxy experiment method, the interaction between PSE and MGE exerts the most prominent effects on substrate bioconversion, and the surfactant complexes show more beneficial effects on steroid bioconversion than the surfactant PSE used alone.

  12. STRUCTURE AND MORPHOLOGY CHANGES OF HYDROBIOTITES MODIFIED BY CATIONIC SURFACTANTS

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    In this study, X-ray diffraction (XRD), Fourier transform infrared spectrometer (FTIR) together with Scanning probe microscopy (SPM) were used to characterize the structure and morphology of the complexes, where the hydrobiotites (Xinjiang) were modified by single-chain surfactants octyltrimethylammonium bromide (OTMA) and octadecyltrimethylammonium bromide (ODTMA). XRD patterns showed that the structure of complexes was significantly influenced by the surfactant concentration and the alkyl chain length, because obvious changes took place in the basal spacing. Furthermore, according to the XRD results, several arrangements of surfactant molecules within the hydrobiotite interlayer space were deduced. The FTIR spectrum indicated that the surfactant contents in complexes dramatically increased with the alkyl chain length. The SPM micrographs demonstrated that the surfaces of complexes prepared at lower surfactant concentration were relatively flat compared with that prepared at higher concentration, while those with higher surfactant concentration had much steeper surface due to the alkyl chain length. It was concluded that structure and morphology of surfactant/hydrobiotite complexes depend not only on the surfactant concentration, but also strongly on the surfactant species.

  13. Formulation of a charcoal suspension for intratumoral injection. Study of galenical excipients.

    Science.gov (United States)

    Bonhomme-Faivre, L; Mathieu, M C; Depraetere, P; Grossiord, J L; Orbach-Arbouys, S; Puisieux, F; Seiller, M

    1999-02-01

    To tattoo human breast cancer prior to chemotherapy, radiotherapy, or surgery, thus allowing a better localization of the remaining tumor by the surgeon, we developed a formulation containing 10% charcoal suspended in water for parenteral preparations. The present study concerns a new step in the development of the charcoal suspension. We sought to determine whether the addition of various excipients could improve the formulation properties and affect the labeling of tumor by the suspension. We have tested surfactants (egg lecithin, polysorbate 80, Cremophor EL, and Pluronic F68), isotonisants (sugars such as glucose and mannitol), polysaccharides (dextrans 20 and 40), and Cabosil, a pyrogenated silica. Except for glucose and mannitol, which were added at a 5% concentration, the other excipients were added at a 0.1% concentration, they were dissolved in water for parenteral injection and sterilized at 120 degrees C for 20 min. We then measured diffusion in vivo in mammary tumor. In vivo, when injected intratumorally in mice, a greater diffusion of charcoal particles was noted within the tumor (in the case of egg lecithin, polysorbate 80, dextran 20 and 40, and glucose) and sometimes in some organs (e.g., Cremophor EL and mannitol). Pluronic F68 slightly improved the stability of the suspension and did not lead to marked diffusion at the injection site, but it showed slight toxicity and cannot be used in the formulation. We concluded that the best formulation was an aqueous 10% micronized peat charcoal suspension.

  14. TOXICITY COMPARISON OF BIOSURFACTANTS AND SYNTHETIC SURFACTANTS USED IN OIL SPILL REMEDIATION TO TWO ESTUARINE SPECIES

    Science.gov (United States)

    The relative environmental toxicities of synthetic and biogenic surfactants used in oil spill remediation efforts are not well understood. Acute and chronic toxicities of three synthetic surfactants and three microbially produced surfactants were determined and compared in this s...

  15. C-reactive protein increases membrane fluidity and distorts lipid lateral organization of pulmonary surfactant. Protective role of surfactant protein A

    DEFF Research Database (Denmark)

    Saenz, Alejandra; Lopez-Sanchez, Almudena; Mojica-Lazaro, Jonas

    2010-01-01

    The purpose of this study was to investigate how surfactant membranes can be perturbed by C-reactive protein (CRP) and whether surfactant protein A (SP-A) might overcome CRP-induced surfactant membrane alterations. The effect of CRP on surfactant surface adsorption was evaluated in vivo after int...

  16. Surfactant-assisted water exposed electrospinning of novel super hydrophilic polycaprolactone based fibers.

    Science.gov (United States)

    Zargarian, S Sh; Haddadi-Asl, V

    2016-05-17

    Hybrid scaffolds prepared by blend electrospinning of Polycaprolactone and Pluronic solution benefit from enhanced fiber hydrophilicity and may offer satisfactory cell attachment and proliferation. To improve hybrid scaffold wettability and water swelling ratio, adequate amount of hydrophilic polymer is required; though this amount is limited by fiber surface enrichment of Pluronic and cannot be exceeded without affecting the scaffold mechanical properties. To overcome this problem, a routine blend electrospinning setup was modified by exposing the blend solution to water in order to attract Pluronic chains toward the surface of the charged jet. Morphology of scaffolds produced by the routine blend electrospinning and modified method was studied. A 50 nm thick Pluronic layer with linty appearance on the surface of the fibers fabricated by the modified method was detected. Drug-loaded fibers from modified method showed a moderate initial burst and then a prolonged release period while an abnormal two-stage phased release profile was observed for the routine blend method. The latter was associated to Pluronic/drug accumulations within the fibers fabricated by the routine method which resulted in fiber disintegration and a subsequent second burst release.

  17. Gd3+-1,4,7,10-Tetraazacyclododecane-1,4,7-triacetic-2-hydroxypropyl-β-cyclodextrin/Pluronic Polyrotaxane as a Long Circulating High Relaxivity MRI Contrast Agent.

    Science.gov (United States)

    Zhou, Zhuxian; Mondjinou, Yawo; Hyun, Seok-Hee; Kulkarni, Aditya; Lu, Zheng-Rong; Thompson, David H

    2015-10-14

    A multivalent magnetic resonance imaging agent based on a 2-hydroxypropyl-β-cyclodextrin (HPCD):Pluronic F127 polyrotaxane carrier has been synthesized, and its blood pool contrast properties have been characterized. This Gd3+-DO3A-HPCD/Pluronic polyrotaxane construct is shown to circulate for more than 30 min and provide >100-fold vascular enhancement relative to the monomeric Gd3+-DO3A-HPCD control that is rapidly cleared via the kidney. The high r1 relaxivity at 37 °C (23.83 mM(-1) s(-1) at 1.5 T; 34.08 mM(-1) s(-1) at 0.5 T), extended blood circulation, well-known pharmacology of the polyrotaxane precursors, and absence of acute toxicity make it a highly attractive blood pool contrast agent candidate.

  18. Effective Surfactants Blend Concentration Determination for O/W Emulsion Stabilization by Two Nonionic Surfactants by Simple Linear Regression

    National Research Council Canada - National Science Library

    Hassan, A K

    2015-01-01

    ...°. Applying the simple linear regression least squares method statistical analysis to the temperature-conductivity obtained data determines the effective surfactants blend concentration required...

  19. Surfactant enhanced disinfection of the human norovirus surrogate, tulane virus with organic acids and surfactant

    Science.gov (United States)

    Human infection with foodborne viruses can occur following consumption of contaminated food, person-to-person body contact, or release of aerosols. Combinatorial treatments of surfactants and organic acids may have synergistic or additive mechanisms to inactivate foodborne viruses and prevent outbr...

  20. Evaluation of Clay and Fumed Silica Nanoparticles on Adsorption of Surfactant Polymer during Enhanced Oil Recovery

    National Research Council Canada - National Science Library

    Cheraghian, Goshtasp

    2017-01-01

    .... The effects of nano concentration on static adsorption of surfactant were investigated at variable condition polymer and surfactant concentration and nanoparticles are critical parameters influence...

  1. Neonatal varicella pneumonia, surfactant replacement therapy

    Directory of Open Access Journals (Sweden)

    Mousa Ahmadpour-kacho

    2015-12-01

    Full Text Available Background: Chickenpox is a very contagious viral disease that caused by varicella-zoster virus, which appears in the first week of life secondary to transplacental transmission of infection from the affected mother. When mother catches the disease five days before and up to two days after the delivery, the chance of varicella in neonate in first week of life is 17%. A generalized papulovesicular lesion is the most common clinical feature. Respiratory involvement may lead to giant cell pneumonia and respiratory failure. The mortality rate is up to 30% in the case of no treatment, often due to pneumonia. Treatment includes hospitalization, isolation and administration of intravenous acyclovir. The aim of this case report is to introduce the exogenous surfactant replacement therapy after intubation and mechanical ventilation for respiratory failure in neonatal chickenpox pneumonia and respiratory distress. Case Presentation: A seven-day-old neonate boy was admitted to the Neonatal Intensive Care Unit at Amirkola Children’s Hospital, Babol, north of Iran, with generalized papulovesicular lesions and respiratory distress. His mother has had a history of Varicella 4 days before delivery. He was isolated and given supportive care, intravenous acyclovir and antibiotics. On the second day, he was intubated and connected to mechanical ventilator due to severe pneumonia and respiratory failure. Because of sever pulmonary involvement evidenced by Chest X-Ray and high ventilators set-up requirement, intratracheal surfactant was administered in two doses separated by 12 hours. He was discharged after 14 days without any complication with good general condition. Conclusion: Exogenous surfactant replacement therapy can be useful as an adjunctive therapy for the treatment of respiratory failure due to neonatal chickenpox.

  2. Size separation of analytes using monomeric surfactants

    Science.gov (United States)

    Yeung, Edward S.; Wei, Wei

    2005-04-12

    A sieving medium for use in the separation of analytes in a sample containing at least one such analyte comprises a monomeric non-ionic surfactant of the of the general formula, B-A, wherein A is a hydrophilic moiety and B is a hydrophobic moiety, present in a solvent at a concentration forming a self-assembled micelle configuration under selected conditions and having an aggregation number providing an equivalent weight capable of effecting the size separation of the sample solution so as to resolve a target analyte(s) in a solution containing the same, the size separation taking place in a chromatography or electrophoresis separation system.

  3. The Krafft temperature of surfactant solutions

    Directory of Open Access Journals (Sweden)

    Manojlović Jelena Ž.

    2012-01-01

    Full Text Available Our main motivation to revisit the solution properties of cetyltrimethylammonium bromide is related to the clear requirement for better control of the adsorption parameters to form uniform self-assembled monolayers on muscovite mica substrates. To readily monitor the temporal evolution of structural details in cetyltrimethylammonium bromide solutions, we realized a rather simple conductivity experiment. Conductivity measurements were carried out as a function of temperature, to look closer into the Krafft temperature behavior of this surfactant. We measured the electrical conductivity of different concentrations of aqueous cetyltrimethylammonium bromide solutions, below and above the critical micells concentration.

  4. Polymeric surfactants for enhanced oil recovery : A review

    NARCIS (Netherlands)

    Raffa, Patrizio; Broekhuis, Antonius A.; Picchioni, Francesco

    Chemical enhanced oil recovery (EOR) is surely a topic of interest, as conventional oil resources become more scarce and the necessity of exploiting heavy and unconventional oils increases. EOR methods based on polymer flooding, surfactant-polymer flooding and alkali-surfactant-polymer flooding are

  5. Endogenous surfactant turnover in preterm infants measured with stable isotopes

    NARCIS (Netherlands)

    J.E.H. Bunt (Jan Erik); L.J.I. Zimmermann (Luc); J.L.D. Wattimena (Josias); R.H.Th. van Beek (Ron); P.J.J. Sauer (Pieter); V.P. Carnielli (Virgilio)

    1998-01-01

    textabstractWe studied surfactant synthesis and turnover in vivo in preterm infants using the stable isotope [U-13C]glucose, as a precursor for the synthesis of palmitic acid in surfactant phosphatidylcholine (PC). Six preterm infants (birth weight, 916 +/- 244 g; gesta

  6. Physical principles for developing a synthetic lung surfactant

    Energy Technology Data Exchange (ETDEWEB)

    Jaehnig, F. (Max-Planck-Institut fuer Biologie, Tuebingen (Germany, F.R.)); Obladen, M. (Tuebingen Univ. (Germany, F.R.). Kinderklinik)

    1984-01-01

    The physical principles for developing a synthetic lung surfactant to treat the respiratory distress syndrome are discussed. Requirements for the lipid composition and preparation of the synthetic surfactant are detailed, leading to the conclusion that a suspension of large unilamellar vesicles consisting of dipalmitoylphosphatidylcholine and a small amount of unsaturated lipid is a promising choice.

  7. Polyfluorinated alkyl phosphate ester surfactants - current knowledge and knowledge gaps

    DEFF Research Database (Denmark)

    Taxvig, Camilla; Rosenmai, Anna Kjerstine; Vinggaard, Anne Marie

    2014-01-01

    information on fluorochemicals. Polyfluorinated alkyl phosphate ester surfactants (PAPs) belong to the group of polyfluorinated alkyl surfactants. They have been detected in indoor dust and are widely used in food-contact materials, from which they have the ability to migrate into food. Toxicological data...

  8. New Focuses on Surfactants for Personal Care Products

    Institute of Scientific and Technical Information of China (English)

    Wang Yan

    2007-01-01

    @@ Global output of surfactants is already more than 12 million tons a year today. There are more than 10 000 varieties in the portfolio. The total market sales value is over US$10 billion. The output of surfactants in China is more than 1.5 million tons a year in recent years. China can manufacture more than 3 380 varieties.

  9. Colloidal stability influenced by inhomogeneous surfactant assemblies in confined spaces

    NARCIS (Netherlands)

    Jodar-Reyes, A.B.; Leermakers, F.A.M.

    2009-01-01

    Recently, a molecular-level self-consistent field approach was used to show that some surfactants assemblies (with local cylindrical structure) can bridge between two surfaces that in turn are covered by surfactant bilayers. The stability of such a connection is related to a higher end-cap (free) en

  10. Studies on the Cloud Points of Nonionic Surfactants with QSPR

    Institute of Scientific and Technical Information of China (English)

    CHEN Mei-ling; WANG Zheng-wu; ZHANG Ge-xin; GU Jin; CUN Zhe; TAO Fu-ming

    2007-01-01

    With quantum chemical parameters, topological indexes, and physical ehemistry parameters as descriptors, a quantitative structure-property relationship(QSPR) has been found for the cloud points of four series of nonionic surfactants(a total of 65 surfactants). The best-regressed model includes six descriptors, and the correlation coefficient of multiple determination is as high as 0. 962.

  11. Surfactant-assisted liquefaction of particulate carbonaceous substances

    Science.gov (United States)

    Hsu, G. C. (Inventor)

    1978-01-01

    A slurry of carbonaceous particles such as coal containing an oil soluble polar substituted oleophilic surfactant, suitably an amine substituted long chain hydrocarbon, is liquefied at high temperature and high hydrogen presence. The pressure of surfactant results in an increase in yield and the conversion product contains a higher proportion of light and heavy oils and less asphaltene than products from other liquefaction processes.

  12. Study of surfactant-skin interactions by skin impedance measurements.

    Science.gov (United States)

    Lu, Guojin; Moore, David J

    2012-02-01

    The stratum corneum (SC) plays a very critical physiological role as skin barrier in regulating water loss through the skin and protects the body from a wide range of physical and chemical exogenous insults. Surfactant-containing formulations can induce skin damage and irritation owing to surfactant absorption and penetration. It is generally accepted that reduction in skin barrier properties occurs only after surfactants have penetrated/permeated into the skin barrier. To mitigate the harshness of surfactant-based cleansing products, penetration/permeation of surfactants should be reduced. Skin impedance measurements have been taken in vitro on porcine skin using vertical Franz diffusion cells to investigate the impact of surfactants, temperature and pH on skin barrier integrity. These skin impedance results demonstrate excellent correlation with other published methods for assessing skin damage and irritation from different surfactant chemistry, concentration, pH, time of exposure and temperature. This study demonstrates that skin impedance can be utilized as a routine approach to screen surfactant-containing formulations for their propensity to compromise the skin barrier and hence likely lead to skin irritation.

  13. A liquid CO2-compatible hydrocarbon surfactant: experiment and modelling

    NARCIS (Netherlands)

    Banerjee, S.; Kleijn, J.M.; Cohen Stuart, M.A.; Leermakers, F.A.M.

    2013-01-01

    Surfactants soluble in liquid CO2 are rare and knowledge on interfacial and self-assembly behaviour is fragmented. We found that polyoxyethylene (5) isooctylphenyl ether is interfacially active at the water–liquid CO2 interface. Water–liquid CO2 interfacial tension was measured at various surfactant

  14. New Y-shaped surfactants from renewable resources.

    Science.gov (United States)

    Ali, Tammar Hussein; Hussen, Rusnah Syahila Duali; Heidelberg, Thorsten

    2014-11-01

    A series of sugar-based surfactants, involving a single hydrophobic chain (C12) and two side-by-side arranged head groups, was prepared form simple glucose precursors. All surfactants were highly water soluble and exhibited exclusively micellar assemblies. This behavior makes them interesting candidates for oil in water emulsifiers. Copyright © 2014 Elsevier B.V. All rights reserved.

  15. Predictive model of cationic surfactant binding to humic substances

    NARCIS (Netherlands)

    Ishiguro, M.; Koopal, L.K.

    2011-01-01

    The humic substances (HS) have a high reactivity with other components in the natural environment. An important factor for the reactivity of HS is their negative charge. Cationic surfactants bind strongly to HS by electrostatic and specific interaction. Therefore, a surfactant binding model is devel

  16. Effect of Gemini-type surfactant on methane hydrate formation

    Energy Technology Data Exchange (ETDEWEB)

    Jeong, K.E.; Park, J.M.; Kim, C.U.; Chae, H.J.; Jeong, S.Y. [Korea Research Inst. of Chemical Technology, Jang-Dong, Yuseong-Gu, Daejeon (Korea, Republic of)

    2008-07-01

    Natural gas hydrates are formed from water and natural gas molecules at particular temperatures and pressures that become ice-like inclusion compounds. Gas hydrates offer several benefits such as energy resource potential and high storage capacity of natural gas in the form of hydrates. However, the application of natural gas hydrates has been deterred by its low formation rate and low conversion ratio of water into hydrate resulting in low actual storage capacity. This paper presented an experimental study to determine the effect of adding a novel Gemini-type surfactant on methane hydrate formation. The experimental study was described with reference to the properties of prepared diols and properties of prepared disulfonates. Gemini surfactant is the family of surfactant molecules possessing more than one hydrophobic tail and hydrophilic head group. They generally have better surface-active properties than conventional surfactants of equal chain length. The paper presented the results of the study in terms of the reactions of diols with propane sultone; storage capacity of hydrate formed with and without surfactant; and methane hydrate formation with and without disulfonate. It was concluded that the methane hydrate formation was accelerated by the addition of novel anionic Gemini-type surfactants and that hydrate formation was influenced by the surfactant concentration and alkyl chain length. For a given concentration, the surfactant with the highest chain length demonstrated the highest formation rate and storage capacity. 5 refs., 3 tabs., 4 figs.

  17. Method of separating a surfactant from a liquid

    NARCIS (Netherlands)

    Van den Berg, A.W.; Lems, S.

    2002-01-01

    The present invention relates to a method of separating a surfactant from a liquid, such as a wastewater stream from an industrial laundry. In accordance with the invention, the liquid is cooled to below the Krafft temperature of the surfactant and subjected to centrifugal forces for the separation

  18. Binding of alkylpyridinium chloride surfactants to sodium polystyrene sulfonate

    NARCIS (Netherlands)

    Ishiguro, M.; Koopal, L.K.

    2009-01-01

    Binding of cationic surfactants to anionic polymers is well studied. However, the surfactant binding characteristics at very low concentration near the start of binding and at high concentration, where charge compensation may Occur. are less well known. Therefore, the binding characteristics of

  19. Enrichment of surfactant from its aqueous solution using ultrasonic atomization.

    Science.gov (United States)

    Takaya, Haruko; Nii, Susumu; Kawaizumi, Fumio; Takahashi, Katsuroku

    2005-08-01

    Dilute aqueous solutions of dodecyl-benzenesulfonic acid sodium salt (DBS-Na) and polyoxyethylenenonylphenyl ethers (PONPEs) were ultrasonically atomized. The surfactants were concentrated in collected mist droplets. The enrichment ratio increased with decreasing surfactant concentration. Depending on the surfactant's molecular weight and affinity to water, different enrichment ratio was observed in the range of low feed concentrations. For anionic surfactant, DBS-Na, the enrichment ratio was significantly improved by KCl addition and a peak appeared on the plot of the ratio against KCl concentration. Addition of NaCl or CaCl2 . 2H2O to the surfactant solution also enhanced the enrichment ratio; however, the effect was relatively small. Such behaviors of the ratio were interpreted as enhanced interfacial adsorption of the surfactant and a lack of supply of surfactant monomers from liquid bulk because of slow breaking of surfactant micelles. Time required for collecting an amount of mist was also observed. Among the three salt systems, the time for KCl system was twice as long as others. This fact suggested that the formation of smaller droplets in KCl system.

  20. Coupled Transport of PAH and Surfactants in Natural Aquifer Material

    Science.gov (United States)

    Danzer, J.; Grathwohl, P.

    1998-03-01

    Surfactants in aqueous solution adsorb onto mineral surfaces and form micelles above the critical micelle concentration (CMC) due to their physico-chemical properties. Hydrophobic organic compounds such as polycyclic aromatic hydrocarbons (PAHs) have a high affinity for the adsorbed surfactant layers (monomers, hemimicelles and admicelles) and to the micelles in the mobile aqueous phase. The transport of PAHs is controlled by the concentration of the surfactant and the partition coefficients, of the PAHs between water and admicelles (adsolubilization: K adm) and water and micelles (solubilization: K mic), respectively. These partition coefficients were measured in laboratory batch and column experiments using phenanthrene as a chemical probe for the PAHs, a non-ionic surfactant (Terrasurf G50), natural aquifer sand (River Neckar Alluvium: RNA) and its petrographic subcomponents. The sorption of the surfactant can be described by a linear isotherm for concentrations below the CMC and a sorption maximum above the CMC, which both depend on the grain size and the surfactant accessible internal surface area of the particles. K adm was found to be higher than K mic. Both depend on the surfactant's properties, such as alkyl chain length, polar headgroup or ethoxylation. In column experiments an increasing retardation of phenanthrene was observed up to the CMC followed by a facilitated transport at surfactant concentration several times the CMC.

  1. Polymeric surfactants for enhanced oil recovery : A review

    NARCIS (Netherlands)

    Raffa, Patrizio; Broekhuis, Antonius A.; Picchioni, Francesco

    2016-01-01

    Chemical enhanced oil recovery (EOR) is surely a topic of interest, as conventional oil resources become more scarce and the necessity of exploiting heavy and unconventional oils increases. EOR methods based on polymer flooding, surfactant-polymer flooding and alkali-surfactant-polymer flooding are

  2. Interaction of photosensitive surfactant with DNA and poly acrylic acid

    Energy Technology Data Exchange (ETDEWEB)

    Zakrevskyy, Yuriy, E-mail: yuriy.zakrevskyy@fh-koeln.de; Paasche, Jens; Lomadze, Nino; Santer, Svetlana, E-mail: santer@uni-potsdam.de [Experimental Physics, Institute of Physics and Astronomy, University of Potsdam, Karl-Liebknecht-Str. 24-25, D-14476 Potsdam (Germany); Cywinski, Piotr; Cywinska, Magdalena; Reich, Oliver; Löhmannsröben, Hans-Gerd [Physical Chemistry, Institute of Chemistry, University of Potsdam, Karl-Liebknecht-Str. 24-25, D-14476 Potsdam (Germany)

    2014-01-28

    In this paper, we investigate interactions and phase transitions in polyelectrolyte-surfactant complexes formed between a cationic azobenzene-containing surfactant and two types of polyelectrolytes: natural (DNA) or synthetic (PAA: poly acrylic acid). The construction of a phase diagram allowed distancing between four major phases: extended coil conformation, colloidally stable compacted globules, colloidal instability range, and surfactant-stabilized compact state. Investigation on the complexes’ properties in different phases and under irradiation with UV light provides information about the role of the surfactant's hydrophobic trans isomers both in the formation and destruction of DNA and PAA globules as well as in their colloidal stabilization. The trans isomer shows much stronger affinity to the polyelectrolytes than the hydrophilic cis counterpart. There is no need for complete compensation of the polyelectrolyte charges to reach the complete compaction. On contrary to the findings previously reported in the literature, we demonstrate – for the first time – complete polyelectrolyte compaction which occurs already at 20% of DNA (and at 50% of PAA) charge compensation. The trans isomer plays the main role in the compaction. The aggregation between azobenzene units in the photosensitive surfactant is a driving force of this process. The decompaction can be realized during UV light irradiation and is strongly influenced by the interplay between surfactant-surfactant and surfactant-DNA interactions in the compacted globules.

  3. Interaction of photosensitive surfactant with DNA and poly acrylic acid

    Science.gov (United States)

    Zakrevskyy, Yuriy; Cywinski, Piotr; Cywinska, Magdalena; Paasche, Jens; Lomadze, Nino; Reich, Oliver; Löhmannsröben, Hans-Gerd; Santer, Svetlana

    2014-01-01

    In this paper, we investigate interactions and phase transitions in polyelectrolyte-surfactant complexes formed between a cationic azobenzene-containing surfactant and two types of polyelectrolytes: natural (DNA) or synthetic (PAA: poly acrylic acid). The construction of a phase diagram allowed distancing between four major phases: extended coil conformation, colloidally stable compacted globules, colloidal instability range, and surfactant-stabilized compact state. Investigation on the complexes' properties in different phases and under irradiation with UV light provides information about the role of the surfactant's hydrophobic trans isomers both in the formation and destruction of DNA and PAA globules as well as in their colloidal stabilization. The trans isomer shows much stronger affinity to the polyelectrolytes than the hydrophilic cis counterpart. There is no need for complete compensation of the polyelectrolyte charges to reach the complete compaction. On contrary to the findings previously reported in the literature, we demonstrate - for the first time - complete polyelectrolyte compaction which occurs already at 20% of DNA (and at 50% of PAA) charge compensation. The trans isomer plays the main role in the compaction. The aggregation between azobenzene units in the photosensitive surfactant is a driving force of this process. The decompaction can be realized during UV light irradiation and is strongly influenced by the interplay between surfactant-surfactant and surfactant-DNA interactions in the compacted globules.

  4. Perfluoroalkyl Epoxides: Synthesis and Conversion into Ionic Surfactants

    Directory of Open Access Journals (Sweden)

    Abdelhamid Ayari

    2014-07-01

    Full Text Available Perfluoroalkylated surfactants having a quaternary ammonium surrounded by three hydroxyl groups as hydrophilic moiety and a perfluoroalkyl chain as tail were obtained by coupling diethanolamine with perfluoroalkylated epoxide followed by quaternisation. The amphiphilic properties of these surfactants were investigated by measuring their surface and interfacial tensions.

  5. New mechanisms for phase separation in polymer-surfactant mixtures

    NARCIS (Netherlands)

    Currie, E.P.K.; Cohen Stuart, M.A.; Borisov, O.V.

    2000-01-01

    The cooperative association of ionic surfactants with polymer chains leads to quite novel features in the phase behaviour of polymer solutions. Using an analytic mean-field model, we analyze phase equilibria in solutions of neutral polymers mixed with ionic surfactants. We predict the possibilities

  6. NUMERICAL SIMULATION AND FIELD IMPLEMENTATION OF SURFACTANT FLOODING

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Based on the features of surfactant flooding, a mathematical model for surfactant flooding is established. The adsorption-retention, convection diffusion of surfactant and influence of concentration change upon relative permeability curve are included in the model. The novel description of adsorption quantity of surfactant and relative permeability curve are presented, which enhance the coincidence between mathematical model and field practice, the relative errors of main development indexes are within 6%. The model is applied to the numerical research of the surfactant flooding in the untabulated beds of Xing1-3 surfactant flooding pilot site of No.4 Oil Production Company of Daqing Oilfield, the influences of surfactant concentration, injection quantity, slug combination mode upon the development effect and economic benefit are quantitatively analyzed, the injection scheme is optimized as follows: surfactant concentration is 0.5%, slug volume is 0.02 PV, slug combination mode is 2 slugs. After the implementation of scheme in oilfield, the cumulative increase of oil is 2186.0 t, up to nearly 30%.

  7. Polymeric surfactants for enhanced oil recovery : A review

    NARCIS (Netherlands)

    Raffa, Patrizio; Broekhuis, Antonius A.; Picchioni, Francesco

    2016-01-01

    Chemical enhanced oil recovery (EOR) is surely a topic of interest, as conventional oil resources become more scarce and the necessity of exploiting heavy and unconventional oils increases. EOR methods based on polymer flooding, surfactant-polymer flooding and alkali-surfactant-polymer flooding are

  8. Theory of interfacial phase transitions in surfactant systems

    Science.gov (United States)

    Shukla, K. P.; Payandeh, B.; Robert, M.

    1991-06-01

    The spin-1 Ising model, which is equivalent to the three-component lattice gas model, is used to study wetting transitions in three-component surfactant systems consisting of an oil, water, and a nonionic surfactant. Phase equilibria, interfacial profiles, and interfacial tensions for three-phase equilibrium are determined in mean field approximation, for a wide range of temperature and interaction parameters. Surfactant interaction parameters are found to strongly influence interfacial tensions, reducing them in some cases to ultralow values. Interfacial tensions are used to determine whether the middle phase, rich in surfactant, wets or does not wet the interface between the oil-rich and water-rich phases. By varying temperature and interaction parameters, a wetting transition is located and found to be of the first order. Comparison is made with recent experimental results on wetting transitions in ternary surfactant systems.

  9. Fate and effects of amphoteric surfactants in the aquatic environment.

    Science.gov (United States)

    Garcia, M Teresa; Campos, Encarna; Marsal, Agustí; Ribosa, Isabel

    2008-10-01

    Amphoteric surfactants form part of specialty surfactants available for formulators to improve or design new formulations in response to environmental, toxicity, safety and performance demands. Nevertheless, limited information on the ecological properties of amphoterics is available. In the present work, the aerobic and anaerobic biodegradability and the aquatic toxicity of different types of amphoteric surfactants (three alkyl betaines, one alkylamido betaine and three alkyl imidazoline derivatives) were studied. The amphoteric surfactants tested were readily biodegradable under aerobic conditions (CO2 headspace test) and alkylamido betaines and alkyl imidazoline derivatives were also easily biodegradable under anaerobic conditions (test based on the ECETOC method). Toxicity to Photobacterium phosphoreum and Daphnia magna increased with the fatty chain length of the surfactant. The EC50 toxicity values of the amphoterics tested were higher than 5 mg/L, and alkyl imidazoline derivatives, with EC50 values from 20 to > 200 mg/L, showed the lowest aquatic toxicity.

  10. Pulmonary Surfactants for Acute and Chronic Lung Diseases (Part II

    Directory of Open Access Journals (Sweden)

    O. A. Rozenberg

    2014-01-01

    Full Text Available Part 2 of the review considers the problem of surfactant therapy for acute respiratory distress syndrome (ARDS in adults and young and old children. It gives information on the results of surfactant therapy and prevention of ARDS in patients with severe concurrent trauma, inhalation injuries, complications due to complex expanded chest surgery, or severe pneumonias, including bilateral pneumonia in the presence of A/H1N1 influenza. There are data on the use of a surfactant in obstetric care and prevention of primary graft dysfunction during lung transplantation. The results of longterm use of surfactant therapy in Russia, suggesting that death rates from ARDS may be substantially reduced (to 20% are discussed. Examples of surfactant therapy for other noncritical lung diseases, such as permanent athelectasis, chronic obstructive pulmonary diseases, and asthma, as well tuberculosis, are also considered.

  11. Surfactant Effects on Microemulsion-Based Nanoparticle Synthesis

    Directory of Open Access Journals (Sweden)

    Concha Tojo

    2010-12-01

    Full Text Available The effect of the surfactant on the size, polydispersity, type of size distribution and structure of nanoparticles synthesized in microemulsions has been studied by computer simulation. The model simulates the surfactant by means of two parameters: the intermicellar exchange parameter, kex, related to dimer life time, and film flexibility parameter, f, related to interdroplet channel size. One can conclude that an increase in surfactant flexibility leads to bigger and polydisperse nanoparticle sizes. In addition, at high concentrations, the same reaction gives rise to a unimodal distribution using a flexible surfactant, and a bimodal distribution using a rigid one. In relation to bimetallic nanoparticles, if the nanoparticle is composed of two metals with a moderate difference in reduction potentials, increasing the surfactant flexibility modifies the nanoparticle structure, giving rise to a transition from a nanoalloy (using a rigid film to a core-shell structure (using a flexible one.

  12. Micellization of monomeric and poly-ω-methacryloyloxyundecyltrimethylammonium surfactants.

    Science.gov (United States)

    FitzGerald, Paul A; Chatjaroenporn, Khwanrat; Zhang, Xiaoli; Warr, Gregory G

    2011-10-04

    We have used small-angle neutron scattering to study how micelle morphology of the tail-polymerizable surfactants MUTAB and MUTAC (ω-methacryloyloxyundecyltrimethylammonium bromide and chloride) is affected by classic self-assembly modifiers such as temperature changes, salt addition, and counterion exchange, as a function of their conversion from monomer into polymer amphiphile in aqueous solution. Contrary to common assumptions about polymerized surfactants, these systems remain in dynamic equilibrium under all conditions examined and at all conversions (except for a small amount of high-molecular-weight precipitation by MUTAC). Counterintuitively, the polymerized methacrylate backbone has little influence on aggregate morphology, except for the formation of rod-like mixed micelles of polymerized and unpolymerized surfactant at intermediate conversions. The addition of salt produces a transition to rod-like micelles at all conversions except in the unpolymerized surfactant, which has some characteristics of an asymmetric bolaform surfactant and retains its spheroidal geometry under almost all conditions.

  13. Aqueous foam surfactants for geothermal drilling fluids: 1. Screening

    Energy Technology Data Exchange (ETDEWEB)

    Rand, P.B.

    1980-01-01

    Aqueous foam is a promising drilling fluid for geothermal wells because it will minimize damage to the producing formation and would eliminate the erosion problems of air drilling. Successful use of aqueous foam will require a high foaming surfactant which will: (1) be chemically stable in the harsh thermal and chemical environment, and (2) form stable foams at high temperatures and pressures. The procedures developed to generate and test aqueous foams and the effects of a 260/sup 0/C temperature cycle on aqueous surfactant solutions are presented. More than fifty selected surfactants were evaluated with representatives from the amphoteric, anionic, cationic, and nonionic classes included. Most surfactants were severely degraded by this temperature cycle; however, some showed excellent retention of their properties. The most promising surfactant types were the alkyl and alkyl aryl sulfonates and the ethoxylated nonionics.

  14. Enhanced solubilization of curcumin in mixed surfactant vesicles.

    Science.gov (United States)

    Kumar, Arun; Kaur, Gurpreet; Kansal, S K; Chaudhary, Ganga Ram; Mehta, S K

    2016-05-15

    Self-assemblies of equimolar double and single chain mixed ionic surfactants, with increasing numbers of carbon atoms of double chain surfactant, were analyzed on the basis of fluorescence and conductivity results. Attempts were also made to enhance the solubilization of curcumin in aqueous equimolar mixed surfactant systems. Mixed surfactant assembly was successful in retarding the degradation of curcumin in alkaline media (only 25-28 40% degraded in 10h at pH 13). Fluorescence spectroscopy and fluorescence quenching methods were employed to predict the binding position and mechanism of curcumin with self-assemblies. Results indicate that the interactions take place according to both dynamic and static quenching mechanisms and curcumin was distributed in a palisade layer of mixed aggregates. Antioxidant activity (using DPPH radical) and biocompatibility (using calf-thymus DNA) of curcumin-loaded mixed surfactant formulations were also evaluated. The prepared systems improved the stability, solubility and antioxidant activity of curcumin and additionally are biocompatible.

  15. Micellization properties of cardanol as a renewable co-surfactant.

    Science.gov (United States)

    Fontana, Antonella; Guernelli, Susanna; Zaccheroni, Nelsi; Zappacosta, Romina; Genovese, Damiano; De Crescentini, Lucia; Riela, Serena

    2015-09-21

    With the aim to improve the features of surfactant solutions in terms of sustainability and renewability we propose the use of hydrogenated natural and sustainable plant-derived cardanol as an additive to commercial surfactants. In the present study we demonstrated that its addition, in amounts as high as 10%, to commercial surfactants of different charge does not significantly affect surfactant properties. Conversely, the presence of hydrogenated cardanol can strongly affect spectrophotometric determination of CMC if preferential interactions with the dyes used take place. This latter evidence may be profitably exploited in surfactant manufacturing by considering that the concurrent presence of a rigid organic molecule such as Orange OT and 10% hydrogenated cardanol decreases the CMC of CTAB up to 65 times.

  16. Delivery and performance of surfactant replacement therapies to treat pulmonary disorders.

    Science.gov (United States)

    El-Gendy, Nashwa; Kaviratna, Anubhav; Berkland, Cory; Dhar, Prajnaparamita

    2013-08-01

    Lung surfactant is crucial for optimal pulmonary function throughout life. An absence or deficiency of surfactant can affect the surfactant pool leading to respiratory distress. Even if the coupling between surfactant dysfunction and the underlying disease is not always well understood, using exogenous surfactants as replacement is usually a standard therapeutic option in respiratory distress. Exogenous surfactants have been extensively studied in animal models and clinical trials. The present article provides an update on the evolution of surfactant therapy, types of surfactant treatment, and development of newer-generation surfactants. The differences in the performance between various surfactants are highlighted and advanced research that has been conducted so far in developing the optimal delivery of surfactant is discussed.

  17. Heat-regulated foaming in surfactant solutions

    Energy Technology Data Exchange (ETDEWEB)

    Pletnev, M.Y.; Eremina, L.D.; Vlasenko, I.G.

    1984-01-01

    This article examines the mechanism of the foam-inhibiting action resulting from the use of propylene oxide derivatives in solutions both of anionic and of nonionic surfactants. The objective is the creation of a detergent composition with heat-regulated foaming, which would foam well at 30-50/sup 0/ and poorly at 80-90/sup 0/, which is the usual temperature of washing machines. It is demonstrated that foaming can be regulated by the variation of the cloud points of solutions with the aid of additions of polypropylene glycols and their alkyl derivatives or block copolymers in solutions of surfactants. Foaming and foam stability decrease sharply above the cloud points of the solutions due to the foam-inhibiting action of the coacervate phase on the coexisting foam-forming solution. The foam inhibition of polypropylene glycols increases and becomes apparent at lower concentrations with the increase of the average molecular weight of the hydrophobic blocks, the increase of their relative content (in block copolymers with oxyethylene groups), and upon the introduction of alkyl groups.

  18. Investigations into surfactant/gas hydrate relationship

    Energy Technology Data Exchange (ETDEWEB)

    Rogers, Rudy; Zhang, Guochang; Dearman, Jennifer; Woods, Charles [Swalm School of Chemical Engineering, Mississippi State University, Mississippi State, MS 39762 (United States)

    2007-03-15

    Gas hydrates have unique physical properties portending useful industrial applications of gas storage, gas separation, or water desalination. When gas hydrates were found in the early 1990s to occur naturally and abundantly in seafloors, three other primary interests and concerns emerged: potential new energy source, climate threat from their greenhouse gases, and seafloor instabilities. This paper presents research showing how anionic synthetic surfactants helped develop an industrial gas hydrate storage process for natural gas and how naturally-occurring in-situ anionic biosurfactants influence the formation and placement of gas hydrates in ocean sediments. The catalytic effects, mechanisms, and surface specificities imparted by synthetic surfactants in the gas storage process and imparted by biosurfactants in porous media are discussed. The Bacillus subtilis bacterium that is indigenous to gas hydrate mounds in the Gulf of Mexico was cultured in the laboratory. Its biosurfactant was separated and found to catalyze gas hydrates in porous media. The experiments indicate that seafloor-biosurfactants can be produced rapidly in-situ to achieve threshold concentrations whereby hydrates are promoted. The biosurfactants accumulate and promote hydrate formation on specific mineral surfaces such as sodium montmorillonite. (author)

  19. Role of lung surfactant in respiratory disease: current knowledge in large animal medicine.

    Science.gov (United States)

    Christmann, U; Buechner-Maxwell, V A; Witonsky, S G; Hite, R D

    2009-01-01

    Lung surfactant is produced by type II alveolar cells as a mixture of phospholipids, surfactant proteins, and neutral lipids. Surfactant lowers alveolar surface tension and is crucial for the prevention of alveolar collapse. In addition, surfactant contributes to smaller airway patency and improves mucociliary clearance. Surfactant-specific proteins are part of the innate immune defense mechanisms of the lung. Lung surfactant alterations have been described in a number of respiratory diseases. Surfactant deficiency (quantitative deficit of surfactant) in premature animals causes neonatal respiratory distress syndrome. Surfactant dysfunction (qualitative changes in surfactant) has been implicated in the pathophysiology of acute respiratory distress syndrome and asthma. Analysis of surfactant from amniotic fluid allows assessment of fetal lung maturity (FLM) in the human fetus and exogenous surfactant replacement therapy is part of the standard care in premature human infants. In contrast to human medicine, use and success of FLM testing or surfactant replacement therapy remain limited in veterinary medicine. Lung surfactant has been studied in large animal models of human disease. However, only a few reports exist on lung surfactant alterations in naturally occurring respiratory disease in large animals. This article gives a general review on the role of lung surfactant in respiratory disease followed by an overview of our current knowledge on surfactant in large animal veterinary medicine.

  20. A multicenter, randomized trial comparing synthetic surfactant with modified bovine surfactant extract in the treatment of neonatal respiratory distress syndrome

    NARCIS (Netherlands)

    Adams, E; Vollman, J; Giebner, D; Maurer, M; Dreyer, G; Bailey, L; Anderson, M; Mefford, L; Beaumont, E; Sutton, D; Puppala, B; Mangurten, HH; Secrest, J; Lewis, WJ; Carteaux, P; Bednarek, F; Welsberger, S; Gosselin, R; Pantoja, AF; Belenky, A; Campbell, P; Patole, S; Duenas, M; Kelly, M; Alejo, W; Lewallen, P; DeanLieber, S; Hanft, M; Ferlauto, J; Newell, RW; Bagwell, J; Levine, D; Lipp, RW; Harkavy, K; Vasa, R; Birenbaum, H; Broderick, KA; Santos, AQ; Long, BA; Gulrajani, M; Stern, M; Hopgood, G; Hegyi, T; Alba, J; Christmas, L; McQueen, M; Nichols, N; Brown, M; Quissell, BJ; Rusk, C; Marks, K; Gifford, K; Hoehn, G; Pathak, A; Marino, B; Hunt, P; Fox, [No Value; Sharpstein, C; Feldman, B; Johnson, N; Beecham, J; Balcom, R; Helmuth, W; Boylan, D; Frakes, C; Magoon, M; Reese, K; Schwersenski, J; Schutzman, D; Soll, R; Horbar, JD; Leahy, K; Troyer, W; Juzwicki, C; Anderson, P; Dworsky, M; Reynolds, L; Urrutia, J; Gupta, U; Adray, C

    1996-01-01

    Objective. To compare the efficacy of a synthetic surfactant (Exosurf Neonatal, Burroughs-Wellcome Co) and a modified bovine surfactant extract (Survanta, Ross Laboratories) in the treatment of neonatal respiratory distress syndrome (RDS). Design. Multicenter, randomized trial. Setting. Thirty-eight

  1. A multicenter, randomized trial comparing synthetic surfactant with modified bovine surfactant extract in the treatment of neonatal respiratory distress syndrome

    NARCIS (Netherlands)

    Adams, E; Vollman, J; Giebner, D; Maurer, M; Dreyer, G; Bailey, L; Anderson, M; Mefford, L; Beaumont, E; Sutton, D; Puppala, B; Mangurten, HH; Secrest, J; Lewis, WJ; Carteaux, P; Bednarek, F; Welsberger, S; Gosselin, R; Pantoja, AF; Belenky, A; Campbell, P; Patole, S; Duenas, M; Kelly, M; Alejo, W; Lewallen, P; DeanLieber, S; Hanft, M; Ferlauto, J; Newell, RW; Bagwell, J; Levine, D; Lipp, RW; Harkavy, K; Vasa, R; Birenbaum, H; Broderick, KA; Santos, AQ; Long, BA; Gulrajani, M; Stern, M; Hopgood, G; Hegyi, T; Alba, J; Christmas, L; McQueen, M; Nichols, N; Brown, M; Quissell, BJ; Rusk, C; Marks, K; Gifford, K; Hoehn, G; Pathak, A; Marino, B; Hunt, P; Fox, [No Value; Sharpstein, C; Feldman, B; Johnson, N; Beecham, J; Balcom, R; Helmuth, W; Boylan, D; Frakes, C; Magoon, M; Reese, K; Schwersenski, J; Schutzman, D; Soll, R; Horbar, JD; Leahy, K; Troyer, W; Juzwicki, C; Anderson, P; Dworsky, M; Reynolds, L; Urrutia, J; Gupta, U; Adray, C

    1996-01-01

    Objective. To compare the efficacy of a synthetic surfactant (Exosurf Neonatal, Burroughs-Wellcome Co) and a modified bovine surfactant extract (Survanta, Ross Laboratories) in the treatment of neonatal respiratory distress syndrome (RDS). Design. Multicenter, randomized trial. Setting. Thirty-eight

  2. The binding and insertion of imidazolium-based ionic surfactants into lipid bilayers: the effects of the surfactant size and salt concentration.

    Science.gov (United States)

    Lee, Hwankyu; Jeon, Tae-Joon

    2015-02-28

    Imidazolium-based ionic surfactants with hydrocarbon tails of different sizes were simulated with lipid bilayers at different salt concentrations. Starting with the random position of ionic surfactants outside the bilayer, surfactants with long tails mostly insert into the bilayer, while those with short tails show the insertion of fewer surfactant molecules, indicating the effect of the tail length. In particular, surfactants with a tail of two or four hydrocarbons insert and reversibly detach from the bilayer, while the inserted longer surfactants cannot be reversibly detached because of the strong hydrophobic interaction with lipid tails, in quantitative agreement with experiments. Longer surfactants insert more deeply and irreversibly into the bilayer and thus increase lateral diffusivities of the bilayer, indicating that longer surfactants more significantly disorder lipid bilayers, which also agrees with experiments regarding the effect of the tail length of ionic surfactants on membrane permeability and toxicity. Addition of NaCl ions weakens the electrostatic interactions between headgroups of surfactants and lipids, leading to the binding of fewer surfactants into the bilayer. In particular, our simulation findings indicate that insertion of ionic surfactants can be initiated by either the hydrophobic interaction between tails of surfactants and lipids or the electrostatic binding between imidazolium heads and lipid heads, and the strength of hydrophobic and electrostatic interactions depends on the tail length of surfactants.

  3. Poly(ester amine Composed of Polyethylenimine and Pluronic Enhance Delivery of Antisense Oligonucleotides In Vitro and in Dystrophic mdx Mice

    Directory of Open Access Journals (Sweden)

    Mingxing Wang

    2016-01-01

    Full Text Available A series of poly(esteramines (PEAs constructed from low molecular weight polyethyleneimine (LPEI and Pluronic were evaluated for the delivery of antisense oligonuclotides (AOs, 2′-O-methyl phosphorothioate RNA (2′-OMePS and phosphorodiamidate morpholino oligomer (PMO in cell culture and dystrophic mdx mice. Improved exon-skipping efficiency of both 2′-OMePS and PMO was observed in the C2C12E50 cell line with all PEA polymers compared with PEI 25k or LF-2k. The degree of efficiency was found in the order of PEA 01, PEA 04 > PEA 05 > others. The in vivo study in mdx mice demonstrated enhanced exon-skipping of 2′-OMePS with the order of PEA 06 > PEA 04, PEA 07 > PEA 03 > PEA 01 > others, and much higher than PEI 25k formulated 2′-OMePS. Exon-skipping efficiency of PMO in formulation with the PEAs were significantly enhanced in the order of PEA 02 > PEA 10 > PEA 01, PEA 03 > PEA 05, PEA 07, PEA 08 > others, with PEA 02 reaching fourfold of Endo-porter formulated PMO. PEAs improve PMO delivery more effectively than 2′-OMePS delivery in vivo, and the systemic delivery evaluation further highlight the efficiency of PEA for PMO delivery in all skeletal muscle. The results suggest that the flexibility of PEA polymers could be explored for delivery of different AO chemistries, especially for antisense therapy.

  4. Hyaluronic acid decorated pluronic P85 solid lipid nanoparticles as a potential carrier to overcome multidrug resistance in cervical and breast cancer.

    Science.gov (United States)

    Wang, Fang; Li, Li; Liu, Bo; Chen, Zhen; Li, Changzhong

    2017-02-01

    This work aimed to develop hyaluronic acid (HA) decorated pluronic 85 (P85) coated solid lipid nanoparticles (SLN) loaded with paclitaxel (HA-PTX-P85-SLN) and to evaluate its potential to overcome drug resistance and to increase antitumor efficacy in mice bearing cervical and breast tumor. P85-Distearoyl Phosphoethanolamine (DSPE) was synthesized from P85 and DSPE by coupling in the presence of 1,10-carbonyldiimidazole (CDI) as a catalyst. The SLN were prepared by the hot homogenization technique and electrostatic interaction. PTX-loaded SLN was characterized for mean diameter, zeta potential, morphology, entrapment efficiency (EE), drug loading capacity (LC) and in vitro drug release. In vivo animal evaluation containing antitumor effect, pharmacokinetics and biodistribution were conducted in mice bearing cervical and breast tumor. The HA-PTX-P85-SLN showed a mean diameter of 160.3nm, negative zeta potential (-31.6mV), EE of 88.2%, and LC of 4.9%. PTX from HA-PTX-P85-SLN exhibited greater sustained drug release profiles compared free PTX. Pharmacokinetics results indicated that HA-PTX-P85-SLN exhibited a 5.5-fold increase in AUC in comparison to free PTX. Biodistribution results revealed that HA-PTX-P85-SLN exhibited higher tumor drug concentration compared with free PTX.

  5. Mechanism of pluronic effect on P-glycoprotein efflux system in blood-brain barrier: contributions of energy depletion and membrane fluidization.

    Science.gov (United States)

    Batrakova, E V; Li, S; Vinogradov, S V; Alakhov, V Y; Miller, D W; Kabanov, A V

    2001-11-01

    Pluronic block copolymer, P85, inhibits the P-glycoprotein (Pgp) drug efflux system and increases the permeability of a broad spectrum of drugs in the blood-brain barrier (BBB). This study examines the mechanisms by which P85 inhibits Pgp using bovine brain microvessel endothelial cells (BBMEC) as an in vitro model of the BBB. The hypothesis was that simultaneous alterations in intracellular ATP levels and membrane fluidization in BBMEC monolayers by P85 results in inhibition of the drug efflux system. The methods included the use of 1) standard Pgp substrate rhodamine 123 to assay the Pgp efflux system in BBMEC, 2) luciferin/luciferase assay for ATP intracellular levels, and 3) 1,6-diphenyl-1,3,5-hexatriene for membrane microviscosity. Using 3H-labeled P85 and fluorescein-labeled P85 for confocal microscopy, this study suggests that P85 accumulates in the cells and intracellular organelles such as the mitochondria where it can interfere with metabolic processes. Following exposure of BBMEC to P85, the ATP levels were depleted, and microviscosity of the cell membranes was decreased. Furthermore, P85 treatment decreased Pgp ATPase activity in membranes expressing human Pgp. A combination of experiments examining the kinetics, concentration dependence, and directionality of P85 effects on Pgp-mediated efflux in BBMEC monolayers suggests that both energy depletion (decreasing ATP pool available for Pgp) and membrane fluidization (inhibiting Pgp ATPase activity) are critical factors contributing to the activity of the block copolymer in the BBB.

  6. RGD Peptides-Conjugated Pluronic Triblock Copolymers Encapsulated with AP-2α Expression Plasmid for Targeting Gastric Cancer Therapy in Vitro and in Vivo

    Directory of Open Access Journals (Sweden)

    Wei Wang

    2015-07-01

    Full Text Available Gastric cancer, a high-risk malignancy, is a genetic disease developing from a cooperation of multiple gene mutations and a multistep process. Gene therapy is a novel treatment method for treating gastric cancer. Here, we developed a novel Arg-Gly-Asp (RGD peptides conjugated copolymers nanoparticles-based gene delivery system in order to actively targeting inhibit the growth of gastric cancer cells. These transcription factor (AP-2α expression plasmids were also encapsulated into pluronic triblock copolymers nanoparticles which was constituted of poly(ethylene glycol-block-poly(propylene glycol- block-poly(ethylene glycol (PEO-block-PPO-block-PEO, P123. The size, morphology and composition of prepared nanocomposites were further characterized by nuclear magnetic resonance (NMR, transmission electron microscopy (TEM and dynamic light scattering (DLS. In MTT (3-(4,5-dimethyl-2-thiazolyl-2,5-diphenyltetrazolium bromide analysis, these nanocomposites have minor effects on the proliferation of GES-1 cells but significantly decreased the viability of MGC-803, suggesting they own low cytotoxicity but good antitumor activity. The following in vivo evaluation experiments confirmed that these nanocomposites could prevent the growth of gastric cancer cells in the tumor xenograft mice model. In conclusion, these unique RGD peptides conjugated P123 encapsulated AP-2α nanocomposites could selectively and continually kill gastric cancer cells by over-expression of AP-2α in vitro and in vivo; this exhibits huge promising applications in clinical gastric cancer therapy.

  7. Formulation and in vitro evaluation of quercetin loaded polymeric micelles composed of pluronic P123 and D-a-tocopheryl polyethylene glycol succinate.

    Science.gov (United States)

    Zhao, Liyan; Shi, Yikang; Zou, Shaohua; Sun, Min; Lil, Lingbing; Zhail, Guangxi

    2011-06-01

    The objective of this study was to develop a polymeric delivery system to improve the solubility and biological activity of Quercetin (QT). QT loaded mixed micelles, composed of Pluronic P123 (P123) and D-a-tocopheryl polyethylene glycol succinate (TPGS) with proportion of 7:3 (QT-P/T), were prepared by thin-film hydration method. The average size of the mixed micelles was 18.43 nm, and the encapsulating efficiency for QT was 88.94 +/- 3.71%, drug-loading was 10.59 +/- 0.38%. The solubility of QT in QT-P/T was 5.56 mg/mL, which was about 2738-fold that of crude QT in water. Compared with the QT propylene glycol solution, the in vitro release of QT from QT-P/T presented the sustained-release property. The in vitro cytotoxicity assay showed that the IC50 values on MCF-7 cells for QT-P/T and QT loaded P123 micelles (QT-P123) were 7.13 microg/mL and 10.73 microg/mL, respectively, while 7.23 microg/mL and 14.47 microg/mL on MCF-7/ADR cells. From the results, it can be concluded that, P123/TPGS mixed micelles may serve as a pharmaceutical nano carrier with improved solubility and biological activity for QT.

  8. Development of chitosan graft pluronic®F127 copolymer nanoparticles containing DNA aptamer for paclitaxel delivery to treat breast cancer cells

    Science.gov (United States)

    Thach Nguyen, Kim; Le, Duc Vinh; Do, Dinh Ho; Huan Le, Quang

    2016-06-01

    HER-2/ErbB2/Neu(HER-2), a member of the epidermal growth factor receptor family, is specifically overexpressed on the surface of breast cancer cells and serves a therapeutic target for breast cancer. In this study, we aimed to isolate DNA aptamer (Ap) that specifically bind to a HER-2 overexpressing SK-BR-3 human breast cancer cell line, using SELEX strategy. We developed a novel multifunctional composite micelle with surface modification of Ap for targeted delivery of paclitaxel. This binary mixed system consisting of Ap modified pluronic®F127 and chitosan could enhance PTX loading capacity and increase micelle stability. Polymeric micelles had a spherical shape and were self-assemblies of block copolymers of approximately 86.22 ± 1.45 nm diameter. PTX could be loaded with high encapsulation efficiency (83.28 ± 0.13%) and loading capacity (9.12 ± 0.34%). The release profile were 29%-35% in the first 12 h and 85%-93% after 12 d at pH 7.5 of receiving media. The IC50 doses by MTT assay showed the greater activity of nanoparticles loaded paclitaxel over free paclitaxel and killed cells up to 95% after 6 h. These results demonstrated unique assembly with the capacity to function as an efficient detection and delivery vehicle in the biological living system.

  9. Nanoemulsion Thermoreversible Pluronic F127-Based Hydrogel Containing Hyptis pectinata (Lamiaceae) Leaf Essential Oil Produced a Lasting Anti-hyperalgesic Effect in Chronic Noninflammatory Widespread Pain in Mice.

    Science.gov (United States)

    Quintans-Júnior, Lucindo J; Brito, Renan G; Quintans, Jullyana S S; Santos, Priscila L; Camargo, Zaine T; Barreto, Péricles A; Arrigoni-Blank, Maria F; Lucca-Júnior, Waldecy; Scotti, Luciana; Scotti, Marcus T; Kolker, Sandra J; Sluka, Kathleen A

    2017-02-13

    We evaluated if a nanostructured thermoreversible Pluronic F127-based hydrogel incorporated with Hyptis pectinata leaf essential oil (NE-EOH) produces a long-lasting anti-hyperalgesic effect on chronic muscle pain in an animal model. We induced chronic muscle pain by injecting the gastrocnemius with saline injections. Paw and muscle withdrawal thresholds and motor performance were evaluated after treatment and compared with morphine, diazepam, or vehicle. Naloxone and methysergide administration tested the involvement of opioid and serotonin receptors, respectively. Sites of action in the central nervous system for the NE-EOH were examined by measuring substance P (SP) levels in the spinal cord and Fos protein in the brainstem. NE-EOH increased paw and muscle withdrawal thresholds when compared with vehicle but had no effect on motor function. This analgesic effect was reversed by both naloxone and methysergide. NE-EOH decreased elevated substance P levels and reduced Fos-labeled neurons in the spinal cord and increased the number of Fos-labeled neurons in the periaqueductal gray (PAG), nucleus raphe magnus (NRM), and locus coeruleus (LC). NE-EOH was shown to produce a lasting anti-hyperalgesic effect. It uses opioid and serotonin receptors, activates brainstem inhibitory pathways, and reduces the release of excitatory neurotransmitters in the spinal cord and is a substance with potential to be used in the treatment of noninflammatory pain conditions. Graphical Abstract.

  10. Perfluorinated Alcohols Induce Complex Coacervation in Mixed Surfactants.

    Science.gov (United States)

    Jenkins, Samuel I; Collins, Christopher M; Khaledi, Morteza G

    2016-03-15

    Recently, we reported a unique and nearly ubiquitous phenomenon of inducing simple and complex coacervation in solutions of a broad variety of individual and mixed amphiphiles and over a wide range of concentrations and mole fractions. This paper describes a novel type of biphasic separation in aqueous solutions of mixed cationic-anionic (catanionic) surfactants induced by hexafluoroisopropanol (HFIP). The test cases included mixtures of cetyltrimethylammonium bromide (CTAB) and sodium dodecyl sulfate (SDS) (surfactants with different carbon chain lengths) as well as dodecyltrimethylammonium bromide (DTAB) with SDS (surfactants with the same carbon chain lengths). The CTAB-SDS-HFIP coacervate systems can be produced at many different mole ratios of surfactant, but DTAB-SDS-HFIP formed only coacervates at equimolar (1:1) mole ratios of DTAB and SDS. The phase-transition behavior of both systems was studied over a wide range of surfactant and HFIP concentrations at the stoichiometric (1:1) mole ratio of cationic/anionic surfactants. The chemical compositions of each of the two phases (aqueous-rich and coacervate phases) were studied with regard to the concentrations of HFIP, water, and individual surfactants. It is revealed that the surfactant-rich phase (coacervate phase) contains a large percentage of fluoroalcohol relative to the aqueous phase and is enriched in both surfactants but contains a small percentage of water. Surprisingly, the concentration of water in the coacervate phase increases as the total HFIP concentration is increased while the concentration of HFIP in the coacervate phase remains relatively constant, which means a larger amount of water associated with HFIP molecules is extracted into the coacervate phase, which results in the growth of the phase. The volume of the coacervate phase increases with an increase in surfactant concentration and total HFIP %. The coacervate phase is highly enriched in the two amphiphilic ions (DTA(+) and DS

  11. High Oxygen Concentrations Adversely Affect the Performance of Pulmonary Surfactant.

    Science.gov (United States)

    Smallwood, Craig D; Boloori-Zadeh, Parnian; Silva, Maricris R; Gouldstone, Andrew

    2017-08-01

    Although effective in the neonatal population, exogenous pulmonary surfactant has not demonstrated a benefit in pediatric and adult subjects with hypoxic lung injury despite a sound physiologic rationale. Importantly, neonatal surfactant replacement therapy is administered in conjunction with low fractional FIO2 while pediatric/adult therapy is administered with high FIO2 . We suspected a connection between FIO2 and surfactant performance. Therefore, we sought to assess a possible mechanism by which the activity of pulmonary surfactant is adversely affected by direct oxygen exposure in in vitro experiments. The mechanical performance of pulmonary surfactant was evaluated using 2 methods. First, Langmuir-Wilhelmy balance was utilized to study the reduction in surface area (δA) of surfactant to achieve a low bound value of surface tension after repeated compression and expansion cycles. Second, dynamic light scattering was utilized to measure the size of pulmonary surfactant particles in aqueous suspension. For both experiments, comparisons were made between surfactant exposed to 21% and 100% oxygen. The δA of surfactant was 21.1 ± 2.0% and 35.8 ± 2.0% during exposure to 21% and 100% oxygen, respectively (P = .02). Furthermore, dynamic light-scattering experiments revealed a micelle diameter of 336.0 ± 12.5 μm and 280.2 ± 11.0 μm in 21% and 100% oxygen, respectively (P < .001), corresponding to a ∼16% decrease in micelle diameter following exposure to 100% oxygen. The characteristics of pulmonary surfactant were adversely affected by short-term exposure to oxygen. Specifically, surface tension studies revealed that short-term exposure of surfactant film to high concentrations of oxygen expedited the frangibility of pulmonary surfactant, as shown with the δA. This suggests that reductions in pulmonary compliance and associated adverse effects could begin to take effect in a very short period of time. If these findings can be demonstrated in vivo, a role for

  12. Characterization of Phase and Emulsion Behavior, Surfactant Retention, and Oil Recovery for Novel Alcohol Ethoxycarboxylate Surfactant

    Energy Technology Data Exchange (ETDEWEB)

    Moeti, Lebone T.; Sampath, Ramanathan

    2002-03-13

    Electrical conductivity measurements for middle, bottom, and top phases, as well as bottom/middle, and middle/bottom conjugate pair phases of the NEODOX 23-4/dodecane/10mM water system were continued from the previous reporting period. Electrical conductivity of the mixture decreased as the fraction of volume of the middle phase was increased and vice versa. Also inversion phenomena was observed. Following this, more emulsion studies at various temperatures were progresses. A theoretical model to predict the conductivity measurements using Maxwell equations was developed and sensitivity analyses to test the performance of the model was completed. Surtek, Golden, CO, our industrial partner in this project, investigated the suitability of the surfactant for enhanced oil recovery employing coreflooding techniques and observed lower surfactant and hydrocarbon recovery for NEODOX 23-4.

  13. Surfactant and nonlinear drop dynamics in microgravity

    Science.gov (United States)

    Jankovsky, Joseph Charles

    2000-11-01

    Large amplitude drop dynamics in microgravity were conducted during the second United States Microgravity Laboratory mission carried onboard the Space Shuttle Columbia (20 October-5 November 1995). Centimeter- sized drops were statically deformed by acoustic radiation pressure and released to oscillate freely about a spherical equilibrium. Initial aspect ratios of up to 2.0 were achieved. Experiments using pure water and varying aqueous concentrations of Triton-X 100 and bovine serum albumin (BSA) were performed. The axisymmetric drop shape oscillations were fit using the degenerate spherical shape modes. The frequency and decay values of the fundamental quadrupole and fourth order shape mode were analyzed. Several large amplitude nonlinear oscillation dynamics were observed. Shape entrainment of the higher modes by the fundamental quadrupole mode occurred. Amplitude- dependent effects were observed. The nonlinear frequency shift, where the oscillation frequency is found to decrease with larger amplitudes, was largely unaffected by the presence of surfactants. The percentage of time spent in the prolate shape over one oscillation cycle was found to increase with oscillation amplitude. This prolate shape bias was also unaffected by the addition of surfactants. These amplitude-dependent effects indicate that the nonlinearities are a function of the bulk properties and not the surface properties. BSA was found to greatly enhance the surface viscoelastic properties by increasing the total damping of the oscillation, while Triton had only a small influence on damping. The surface concentration of BSA was found to be diffusion-controlled over the time of the experiments, while the Triton diffusion rate was very rapid. Using the experimental frequency and decay values, the suface viscoelastic properties of surface dilatational viscosity ( ks ) and surface shear viscosity ( ms ) were found for varying surfactant concentrations using the transcendental equation of Lu

  14. Preparation and evaluation of sulphonamide nonionic surfactants

    Directory of Open Access Journals (Sweden)

    Ahmed, M. H. M.

    2010-03-01

    Full Text Available Alkyl (octyl, decyl and dodecyl; C8,C10 and C12 benzene sulphonyl chloride was used in the preparation of a novel series of nonionic surfactants (IV-VIa-c, (VII-IX a-c and (X-XIIa-c. The preparations were completed by reacting each alkyl (C8,C10 and C12 benzene sulphonyl chloride with ethanolamine to give (I-III respectively. The resulting products were reacted separately with ethylene oxide in the presence of different (base KOH, Lewis acid SnCl4 and k10 clay catalysts to produce different moles of nonionic surfactants (5, 7 and 9 in sequence corresponding to (IV-VIa-c, (VII-IX a-c and (X-XIIa-c respectively. The chemical structures of prepared nonionic surfactants were elucidated by IR and 1HNMR spectra. The surface activity, biodegradability and biological activities of the prepared compounds were investigated. The obtained data show that these compounds have good surface and biological activities as well as reasonable biodegradability properties.Cloruros de sulfonilbenceno alquilados (octil, decil, dodecil; C8, C10 y C12 fueron usados en la preparación de una nueva serie de surfactantes no iónicos (IV-VIa-c, (VII-IX a-c and (X-XIIa-c. Las preparaciones fueron completadas por reacción de cada cloruro de sulfonilbenceno alquilado (C8, C10 y C12 con etanolamina para dar los compuestos (IIII, respectivamente. Los anteriores productos reaccionaron separadamente con óxido de etileno en presencia de diferentes catalizadores (la base KOH, el ácido de Lewis SnCl4 y la arcilla k10 para producir secuencialmente diferentes surfactantes no iónicos con distintos moles de óxido de etileno (5, 7 y 9: (IV-VIa-c, (VII-IXa-c and (X-XIIa-c, respectivamente. La estructura química de los surfactantes no iónicos preparados fueron elucidadas mediante sus espectros de IR y 1H RMN. Las propiedades tensoactivas, biodegradabilidad y actividad biológica de los compuestos preparados fueron investigados. Los datos obtenidos muestran que estos compuestos tienen

  15. The effect of surfactant on pollutant biosorption of Trametes versicolor

    Science.gov (United States)

    Gül, Ülküye Dudu; Silah, Hülya; Akbaş, Halide; Has, Merve

    2016-04-01

    The major problem concerning industrial wastewater is treatment of dye and heavy metal containing effluents. Industrial effluents are also contained surfactants that are used as levelling, dispersing and wetting agents. The purpose of this study was to investigate the effect of surfactant on textile dye biosorption properties of a white rot fungus named Trametes versicolor. Reactive dyes are commonly used in textile industry because of their advantages such as brightness and excellent color fastness. A recative textile dye, called Everzol Black, was used in this study. The low-cost mollasses medium is used for fungal growth. The usage of mollases, the sugar refinery effluent as a source of energy and nutrients, gained importance because of reducing the cost and also reusing another waste. In biosorption process the effect of surfactant on dye removal properties of T. versicolor was examined as a function of pH, dye consentration and surfactant concentration. The results of this study showed that the surfactant enhanced the dye removal capacity of Trametes versicolor. The dye and surfactant molecules were interacted electrostatically and these electrostatic interactions improved dye removal properties of filamentous fungus T. versicolor. The results of this study recommended the use of surfactants as an inducer in textile wastewater treatment technologies.

  16. Surfactant aggregation and its application to drag reduction

    Energy Technology Data Exchange (ETDEWEB)

    Harwigsson, I.

    1995-09-01

    A number of different drag-reducing (DR) surfactants: nonionics, zwitterionics and ampholytics suitable for use in both cool and hot water solution are described. These surfactants have been tested under various conditions common in district energy distribution. The surfactants described are environmentally more acceptable than the organic salts of quaternary ammonium compounds which have so far dominated as DR surfactants. The micellar phase formed in water by the surfactant system cetylpyridinium chloride/sodium salicylate has been investigated with surfactant self-diffusion (NMR) measurements and cryo-transmission electron microscopy. Results from this study support the hypothesis that worm-like micellar systems form a network before the phase boundary, when the first liquid crystalline phase formed is a bicontinuous cubic phase. A series of surfactants similar to the one used in the DR experiments has been examined in dilute solutions. Critical micellar concentration and the size of these micelles are investigated as a function of the amphiphile concentration, the pH and salt concentration. Adsorption properties on silica of zwitterionic dodecyl-N,N-dimethylammonio alkanoates, with polymethylene interchange arms of different lengths, have been investigated with an in situ ellipsometry technique. The use of two-tone frequency modulation spectroscopy as a general method for the determination of water activity has been initiated. 173 refs, 6 figs

  17. Sublethal effect of agronomical surfactants on the spider Pardosa agrestis.

    Science.gov (United States)

    Niedobová, Jana; Hula, Vladimír; Michalko, Radek

    2016-06-01

    In addition to their active ingredients, pesticides contain also additives - surfactants. Use of surfactants has been increasing over the past decade, but their effects on non-target organisms, especially natural enemies of pests, have been studied only very rarely. The effect of three common agrochemical surfactants on the foraging behavior of the wolf spider Pardosa agrestis was studied in the laboratory. Differences in short-term, long-term, and overall cumulative predatory activities were investigated. We found that surfactant treatment significantly affected short-term predatory activity but had no effect on long-term predatory activity. The surfactants also significantly influenced the cumulative number of killed prey. We also found the sex-specific increase in cumulative kills after surfactants treatment. This is the first study showing that pesticide additives have a sublethal effect that can weaken the predatory activity of a potential biological control agent. More studies on the effects of surfactants are needed to understand how they affect beneficial organisms in agroecosystems.

  18. Surfactants in atmospheric aerosols and rainwater around lake ecosystem.

    Science.gov (United States)

    Razak, Intan Suraya; Latif, Mohd Talib; Jaafar, Shoffian Amin; Khan, Md Firoz; Mushrifah, Idris

    2015-04-01

    This study was conducted to determine the composition of surfactants in atmospheric aerosols and rainwater in the vicinity of Lake Chini, Malaysia. Samples of atmospheric aerosol and rainwater were collected between March and September 2011 using a high volume air sampler (HVAS) and glass bottles equipped with funnel. Colorimetric analysis was undertaken to determine the concentration of anionic surfactants as methylene blue active substances (MBAS) and cationic surfactants as disulphine blue active substances (DBAS). The water-soluble ionic compositions were determined using inductively coupled plasma mass spectrometry for cations (Na, K, Mg and Ca) and ion chromatography equipped with a conductivity detector for anions (F(-), Cl(-), NO3(-), and SO4(2-)) and the Nessler Method was used to obtain the NH4(+) concentrations. The source apportionment of MBAS and DBAS in atmospheric aerosols was identified using a combination of principal component analysis (PCA) and multiple linear regression (MLR). The results revealed that the concentrations of surfactants in atmospheric aerosols and rainwater were dominated by anionic surfactants as MBAS. The concentration of surfactants as MBAS and DBAS was dominated in fine mode compared to coarse mode aerosols. Using PCA/MLR analysis, two major sources of atmospheric surfactants to Lake Chini were identified as soil dust (75 to 93%) and biomass burning (2 to 22%).

  19. Sorptive affinity of ionic surfactants on silt loamy soil

    Directory of Open Access Journals (Sweden)

    Xingchao Qi

    2016-10-01

    Full Text Available Due to their broad applications, ionic surfactants have already been released into or utilized in soil and environmental systems. However, current understanding on the sorption behavior of surfactants onto soils is still limited. This work systematically investigated the sorption kinetics and isotherms of one cationic surfactant, cetyltrimethylammonium bromide (CTAB, and one anionic surfactant, sodium dodecyl sulfate (SDS, onto a silt loamy soil to determine the governing sorption mechanisms. The pseudo-second-order rate equation described the sorption kinetics data better than the pseudo-first-order rate equation. Experimental data showed that the sorption equilibrium for CTAB and SDS were reached at 24 and 240 h, respectively. Langmuir equation was better than Freundlich equation in simulating the sorption isotherms of CTAB and SDS on the soil. Soil Langmuir maximum sorption capacity of CTAB was much higher than that to SDS. When the experimental temperature increased, the sorption of CTAB and SDS on the soil decreased. In addition, the sorptive process of the surfactants on the soil was spontaneous and exothermal, as indicated by the absolute values of Gibbs free energy and enthalpy. The results also indicated that physical sorption was the dominant mechanism for the sorption of the two surfactants on the soil. Findings from this work are crucial to understand the environmental behaviors of ionic surfactants.

  20. Characterization and control of surfactant-mediated Norovirus interactions.

    Science.gov (United States)

    Mertens, Brittany S; Velev, Orlin D

    2015-11-28

    Understanding of the colloidal interactions of Norovirus particles in aqueous medium could provide insights on the origins of the notorious stability and infectivity of these widespread viral agents. We characterized the effects of solution pH and surfactant type and concentration on the aggregation, dispersion, and disassembly of Norovirus virus-like particles (VLPs) using dynamic light scattering, electrophoretic light scattering, and transmission electron microscopy. Owing to net negative surface charge of the VLPs at neutral pH, low concentrations of cationic surfactant tend to aggregate the VLPs, whereas low concentrations of anionic surfactant tend to disperse the particles. Increasing the concentration of these surfactants beyond their critical micelle concentration leads to virus capsid disassembly and breakdown of aggregates. Non-ionic surfactants, however, had little effect on virus interactions and likely stabilized them additionally in suspension. The data were interpreted on the basis of simple models for surfactant binding and re-charging of the virus capsid. We used zeta potential data to characterize virus surface charge and interpret the mechanisms behind these demonstrated surfactant-virus interactions. The fundamental understanding and control of these interactions will aid in practical formulations for virus inactivation and removal from contaminated surfaces.

  1. Surfactants in microbiology and biotechnology: Part 2. Application aspects.

    Science.gov (United States)

    Singh, Ajay; Van Hamme, Jonathan D; Ward, Owen P

    2007-01-01

    Surfactants are amphiphilic compounds which can reduce surface and interfacial tensions by accumulating at the interface of immiscible fluids and increase the solubility, mobility, bioavailability and subsequent biodegradation of hydrophobic or insoluble organic compounds. Chemically synthesized surfactants are commonly used in the petroleum, food and pharmaceutical industries as emulsifiers and wetting agents. Biosurfactants produced by some microorganisms are becoming important biotechnology products for industrial and medical applications due to their specific modes of action, low toxicity, relative ease of preparation and widespread applicability. They can be used as emulsifiers, de-emulsifiers, wetting and foaming agents, functional food ingredients and as detergents in petroleum, petrochemicals, environmental management, agrochemicals, foods and beverages, cosmetics and pharmaceuticals, and in the mining and metallurgical industries. Addition of a surfactant of chemical or biological origin accelerates or sometimes inhibits the bioremediation of pollutants. Surfactants also play an important role in enhanced oil recovery by increasing the apparent solubility of petroleum components and effectively reducing the interfacial tensions of oil and water in situ. However, the effects of surfactants on bioremediation cannot be predicted in the absence of empirical evidence because surfactants sometimes stimulate bioremediation and sometimes inhibit it. For medical applications, biosurfactants are useful as antimicrobial agents and immunomodulatory molecules. Beneficial applications of chemical surfactants and biosurfactants in various industries are discussed in this review.

  2. EXPERIMENTAL CHARACTERIZATION OF FLUOROCARBON-MODIFIED POLYACRYLAMIDE/SURFACTANT AQUEOUS SOLUTIONS

    Institute of Scientific and Technical Information of China (English)

    Huai-tian Bu; Zhen-zhong Yang; Yun-xiang Zhang

    2003-01-01

    The interaction between surfactants and fluorocarbon-modified polyacrylamide (FC-PAM) in aqueous solutions was evaluated by theological means and fluorescence spectroscopy and was found to be strong regardless of the surfactant's nature. Two representative surfactants, anionic sodium dodecyl sulfate (SDS) and nonionic Triton X-100, were used. The origin of the interaction and its dependence on the surfactant concentration were discussed.

  3. Is surfactant a promising additive drug in ALI/ARDS-patients?

    NARCIS (Netherlands)

    Schultz, MJ; Kesecioglu, J

    2004-01-01

    The rationale for surfactant replacement therapy in patients with acute respiratory distress syndrome (ARDS) is to restore the normal composition of the surfactant system, as well as to overcome ongoing inactivation of present surfactant. Indeed, surfactant replacement therapy call normalize the com

  4. Solubilization of pentanol by cationic surfactants and binary mixtures of cationic surfactants

    Energy Technology Data Exchange (ETDEWEB)

    Morgan, M.E.

    1993-12-31

    The research reported here has included studies of the solubilization of pentanol in hexadecylpyridinium chloride (CPC), trimethyletetradecylammonium chloride (C{sub 14}Cl), benzyldimethyltetradecylammonium chloride (C{sub 14}BzCl), benzyldimethylhexadecylpyridinium chloride (C{sub 16}BzCl), hexadecyltrimethylammonium bromide (CTAB), and binary mixtures of CPC + C{sub 16}BzCl and C{sub 14}Cl + C{sub 14}BzCl. Rather than using calorimetric methods, this project will employ headspace chromatography to measure solubilization of pentanol over a wide range of solute concentrations. While not yielding as much thermodynamic data as calorimetry, headspace chromatography is a more direct measure of the extent of solubilization. Using headspace chromatography, is a more direct measure of the extent of solubilization. Using headspace chromatography, this study will seek to determine whether strongly synergistic mixture ratios exist in the case of binary cationic surfactant systems. There are two equilibria in the pentanol-water-surfactant system: (1) The pentanol solubilized in micelles is in equilibrium with the monomeric pentanol in solution, and (2) the monomeric pentanol is in equilibrium with the pentanol in the vapor above the solution. To establish the link between the two equilibria, a sample of the vapor above pure liquid pentanol must be collected, in order to find the activity of pentanol in solution. Also, a calibration curve for various concentrations of pentanol in solution. From this type of data it is possible to infer both the concentration of pentanol solubilized in micelles and the concentrations of pentanol in the ``bulk`` solution outside the micelles. The method is equally applicable to systems containing a single surfactant as well as mixtures of surfactants.

  5. Gemini ester quat surfactants and their biological activity.

    Science.gov (United States)

    Łuczyński, Jacek; Frąckowiak, Renata; Włoch, Aleksandra; Kleszczyńska, Halina; Witek, Stanisław

    2013-03-01

    Cationic gemini surfactants are an important class of surface-active compounds that exhibit much higher surface activity than their monomeric counterparts. This type of compound architecture lends itself to the compound being easily adsorbed at interfaces and interacting with the cellular membranes of microorganisms. Conventional cationic surfactants have high chemical stability but poor chemical and biological degradability. One of the main approaches to the design of readily biodegradable and environmentally friendly surfactants involves inserting a bond with limited stability into the surfactant molecule to give a cleavable surfactant. The best-known example of such a compound is the family of ester quats, which are cationic surfactants with a labile ester bond inserted into the molecule. As part of this study, a series of gemini ester quat surfactants were synthesized and assayed for their biological activity. Their hemolytic activity and changes in the fluidity and packing order of the lipid polar heads were used as the measures of their biological activity. A clear correlation between the hemolytic activity of the tested compounds and their alkyl chain length was established. It was found that the compounds with a long hydrocarbon chain showed higher activity. Moreover, the compounds with greater spacing between their alkyl chains were more active. This proves that they incorporate more easily into the lipid bilayer of the erythrocyte membrane and affect its properties to a greater extent. A better understanding of the process of cell lysis by surfactants and of their biological activity may assist in developing surfactants with enhanced selectivity and in widening their range of application.

  6. Novel fluorinated gemini surfactants with γ-butyrolactone segments.

    Science.gov (United States)

    Kawase, Tokuzo; Okada, Kazuyuki; Oida, Tatsuo

    2015-01-01

    In this work, novel γ-butyrolactone-type monomeric and dimeric (gemini) surfactants with a semifluoroalkyl group [Rf- (CH2)3-; Rf = C4F9, C6F13, C8F17] as the hydrophobic group were successfully synthesized. Dimethyl malonate was dimerized or connected using Br(CH2)sBr (s = 0, 1, 2, 3) to give tetraesters, and they were bis-allylated. Radical addition of fluoroalkyl using Rf-I and an initiator, i.e., 2,2'-azobisisobutyronitrile for C4F9 or di-t-butyl peroxide for C6F13 and C8F17, was perform at high temperature, with prolonged heating, to obtain bis(semifluoroalkyl)-dilactone diesters. These dilactone diesters were hydrolyzed using KOH/EtOH followed by decarboxylation in AcOH to afford γ-butyrolactonetype gemini surfactants. Common 1 + 1 semifluoroalkyl lactone surfactants were synthesized using the same method. Their surfactant properties [critical micelle concentration (CMC), γCMC, pC20, ΓCMC, and AG] were investigated by measuring the surface tension of the γ-hydroxybutyrate form prepared in aqueous tetrabutylammonium hydroxide solution. As expected, the CMC values of the gemini surfactants were more than one order of magnitude smaller than those of the corresponding 1 + 1 surfactants. Other properties also showed the excellent ability of the gemini structure to reduce the surface tension. These surfactants were easily and quantitatively recovered by acidification. The monomeric surfactant was recovered in the γ-hydroxybutyric acid form, and the gemini surfactant as a mixture of γ-butyrolactone and γ-hydroxybutyric acid forms.

  7. Single well surfactant test to evaluate surfactant floods using multi tracer method

    Science.gov (United States)

    Sheely, Clyde Q.

    1979-01-01

    Data useful for evaluating the effectiveness of or designing an enhanced recovery process said process involving mobilizing and moving hydrocarbons through a hydrocarbon bearing subterranean formation from an injection well to a production well by injecting a mobilizing fluid into the injection well, comprising (a) determining hydrocarbon saturation in a volume in the formation near a well bore penetrating formation, (b) injecting sufficient mobilizing fluid to mobilize and move hydrocarbons from a volume in the formation near the well bore, and (c) determining the hydrocarbon saturation in a volume including at least a part of the volume of (b) by an improved single well surfactant method comprising injecting 2 or more slugs of water containing the primary tracer separated by water slugs containing no primary tracer. Alternatively, the plurality of ester tracers can be injected in a single slug said tracers penetrating varying distances into the formation wherein the esters have different partition coefficients and essentially equal reaction times. The single well tracer method employed is disclosed in U.S. Pat. No. 3,623,842. This method designated the single well surfactant test (SWST) is useful for evaluating the effect of surfactant floods, polymer floods, carbon dioxide floods, micellar floods, caustic floods and the like in subterranean formations in much less time and at much reduced cost compared to conventional multiwell pilot tests.

  8. Surfactant replacement therapy for preterm and term neonates with respiratory distress.

    Science.gov (United States)

    Polin, Richard A; Carlo, Waldemar A

    2014-01-01

    Respiratory failure secondary to surfactant deficiency is a major cause of morbidity and mortality in preterm infants. Surfactant therapy substantially reduces mortality and respiratory morbidity for this population. Secondary surfactant deficiency also contributes to acute respiratory morbidity in late-preterm and term neonates with meconium aspiration syndrome, pneumonia/sepsis, and perhaps pulmonary hemorrhage; surfactant replacement may be beneficial for these infants. This statement summarizes the evidence regarding indications, administration, formulations, and outcomes for surfactant-replacement therapy. The clinical strategy of intubation, surfactant administration, and extubation to continuous positive airway pressure and the effect of continuous positive airway pressure on outcomes and surfactant use in preterm infants are also reviewed.

  9. Preparation and anti-bacterial properties of a temperature sensitive gel containing silver nanoparticles

    Science.gov (United States)

    The purpose of this study was to prepare a novel temperature-sensitive spray gel containing silver nanoparticles and investigate its anti-bacterial properties in vitro. Methods: The aqueous complex gel was prepared by Pluronic F127 (18-22%) and Pluronic F68 (3-9%) through a cold method to obtain a p...

  10. Surfactant-based critical phenomena in microgravity

    Science.gov (United States)

    Kaler, Eric W.; Paulaitis, Michael E.

    1994-01-01

    The objective of this research project is to characterize by experiment and theoretically both the kinetics of phase separation and the metastable structures produced during phase separation in a microgravity environment. The particular systems we are currently studying are mixtures of water, nonionic surfactants, and compressible supercritical fluids at temperatures and pressures where the coexisting liquid phases have equal densities (isopycnic phases). In this report, we describe experiments to locate equilibrium isopycnic phases and to determine the 'local' phase behavior and critical phenomena at nearby conditions of temperature, pressure, and composition. In addition, we report the results of preliminary small angle neutron scattering (SANS) experiments to characterize microstructures that exist in these mixtures at different fluid densities.

  11. New multifunctional surfactants from natural phenolic acids.

    Science.gov (United States)

    Centini, Marisanna; Rossato, Maria Sole; Sega, Alessandro; Buonocore, Anna; Stefanoni, Sara; Anselmi, Cecilia

    2012-01-11

    Several new multifunctional molecules derived from natural sources such as amino acids and hydroxycinnamic acids were synthesized. They exhibit various activities such as emulsifying, UV-protecting, and radical scavenging, thereby conforming to the latest requirements for cosmetic ingredients. The synthesis comprises only a few steps: (i) the amino acid, the acid groups of which are protected by esterification, is coupled with ferulic or caffeic acid; (ii) the p-hydroxyl group of the cinnamic derivative reacts with dodecyl bromide in the presence of potassium carbonate (the resulting compounds are highly lipophilic and tested as water/oil (W/O) emulsifiers); (iii) these molecules, by deprotonating the acid groups of the amino acids, with successive salification, are more hydrophilic, with stronger O/W emulsifying properties. The new multifunctional surfactants might prove useful for the treatment of multiple skin conditions, including loss of cellular antioxidants, damage from free radicals, damage from UV, and others.

  12. Surfactant protein D is proatherogenic in mice

    DEFF Research Database (Denmark)

    Sorensen, Grith L; Madsen, Jens; Kejling, Karin

    2006-01-01

    Surfactant protein D (SP-D) is an important innate immune defense molecule that mediates clearance of pathogens and modulates the inflammatory response. Moreover, SP-D is involved in lipid homeostasis, and pulmonary accumulation of phospholipids has previously been observed in SP-D-deficient (Spd......-/-) mice. Atherogenesis involves both inflammation and lipid deposition, and we investigated the role of SP-D in the development of atherosclerosis. SP-D synthesis was localized to vascular endothelial cells. Atherosclerotic lesion areas were 5.6-fold smaller in the aortic roots in Spd-/- mice compared...... with wild-type C57BL/6N mice on an atherogenic diet. HDL cholesterol (HDL-C) was significantly elevated in Spd-/- mice. Treatment of Spd-/- mice with a recombinant fragment of human SP-D resulted in decreases of HDL-C (21%) as well as total cholesterol (26%), and LDL cholesterol (28%). Plasma TNF...

  13. Preparation and characterization of bolaform surfactant vesicles.

    Science.gov (United States)

    Muzzalupo, Rita; Trombino, Sonia; Iemma, Francesca; Puoci, Francesco; La Mesa, Camillo; Picci, Nevio

    2005-12-10

    Vesicular formulations (liposomes and niosomes) play an increasingly important role since they can be used as drug delivery and targeting systems. We described the formation of two niosomal systems based on synthetic bolaform surfactants (4,7,10,13-pentaoxa-16-aza-cyclooctadecane)-hexadecanedioc acid diamide (BD-16) and alpha,omega-(4,7,10,13-pentaoxa-16-aza-cyclooctadecane)-hexadecane (BC-16). Systems containing BD-16 or BC-16 and different amount of cholesterol (CH) were prepared by aqueous dispersion of films, followed by examination of methylene blue (MB) entrapment, particle size and morphology. Indeed, we also studied the hydration in the distilled water and physiological solution, in order to investigate the complexing ability on vesicle formation. The results obtained in this study show a high encapsulation capacity and this ability and the size depends on cholesterol content.

  14. Synthesis and properties of novel gemini surfactant with short spacer

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Cationic gemini surfactant dimethylene-1,2-bis(dodecyldiethylammonium bromide), referred to as C12C2C12(Et) was synthesized, and its surface property and aggregation behavior in aqueous solution were studied. The value of γat the critical micelle concentration (γcmc) is much smaller than that of the surfactant homologues with longer spacer. Spherical and elongated micelles were formed in the aqueous solution of this gemini surfactant,and the spherical micelles were absolutely dominant compared to the elongated micelles at our studied concentration quantitatively.

  15. Effect of surfactant for magnetic properties of iron oxide nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Haracz, S. [Faculty of Chemistry, Adam Mickiewicz University, Umultowska 89B, 61-614 Poznań (Poland); Hilgendorff, M. [Freie Universität Berlin, Fachbereich Physik, Arnimalle 14, 14195 Berlin (Germany); Rybka, J.D. [Faculty of Chemistry, Adam Mickiewicz University, Umultowska 89B, 61-614 Poznań (Poland); Giersig, M. [Faculty of Chemistry, Adam Mickiewicz University, Umultowska 89B, 61-614 Poznań (Poland); Freie Universität Berlin, Fachbereich Physik, Arnimalle 14, 14195 Berlin (Germany)

    2015-12-01

    Highlights: • Dynamic behavior of magnetic nanoparticles. • Synthesis of iron oxide nanoparticles. • Effect of surfactant for magnetic properties. - Abstract: For different medical applications nanoparticles (NPs) with well-defined magnetic properties have to be used. Coating ligand can change the magnetic moment on the surface of nanostructures and therefore the magnetic behavior of the system. Here we investigated magnetic NPs in a size of 13 nm conjugated with four different kinds of surfactants. The surface anisotropy and the magnetic moment of the system were changed due to the presence of the surfactant on the surface of iron oxide NPs.

  16. Synthesis of Branch Fluorinated Cationic Surfactant and Surface Properties

    Directory of Open Access Journals (Sweden)

    Hongke Wu

    2014-01-01

    Full Text Available A novel fluorinated quaternary ammonium salt cationic surfactant N,N,N-trimethyl-2-[[4-[[3,4,4,4-tetrafluoro-2-[1,2,2,2-tetrafluoro-1-(trifluoromethylethyl]-1,3-bis(tri-fluoromethyl-1-buten-1-yl]oxy]-benzoyl]amino]-iodide (FQAS was synthesized successfully, and its structure was characterized by FTIR, 1H-NMR, 19F-NMR, and MS. The surface activities of FQAS and the effect of temperature, electrolyte, and combination with hydrocarbon surfactant were investigated. The results showed that FQAS exhibited excellent surface activity and combination with hydrocarbon surfactant.

  17. Key interactions of surfactants in therapeutic protein formulations: A review.

    Science.gov (United States)

    Khan, Tarik A; Mahler, Hanns-Christian; Kishore, Ravuri S K

    2015-11-01

    Proteins as amphiphilic, surface-active macromolecules, demonstrate substantial interfacial activity, which causes considerable impact on their multifarious applications. A commonly adapted measure to prevent interfacial damage to proteins is the use of nonionic surfactants. Particularly in biotherapeutic formulations, the use of nonionic surfactants is ubiquitous in order to prevent the impact of interfacial stress on drug product stability. The scope of this review is to convey the current understanding of interactions of nonionic surfactants with proteins both at the interface and in solution, with specific focus to their effects on biotherapeutic formulations.

  18. Amino acid–based surfactants: New antimicrobial agents.

    Science.gov (United States)

    Pinazo, A; Manresa, M A; Marques, A M; Bustelo, M; Espuny, M J; Pérez, L

    2016-02-01

    The rapid increase of drug resistant bacteria makes necessary the development of new antimicrobial agents. Synthetic amino acid-based surfactants constitute a promising alternative to conventional antimicrobial compounds given that they can be prepared from renewable raw materials. In this review, we discuss the structural features that promote antimicrobial activity of amino acid-based surfactants. Monocatenary, dicatenary and gemini surfactants that contain different amino acids on the polar head and show activity against bacteria are revised. The synthesis and basic physico-chemical properties have also been included.

  19. Complex phase behavior in solvent-free nonionic surfactants

    DEFF Research Database (Denmark)

    Hillmyer, M.A.; Bates, F.S.; Almdal, K.

    1996-01-01

    Unsolvated block copolymers and surfactant solutions are ''soft materials'' that share a common set of ordered microstructures, A set of polyethyleneoxide-polyethylethylene (PEG-PEE) block copolymers that are chemically similar to the well-known alkane-oxyethylene (C(n)EO(m)) nonionic surfactants...... was synthesized here. The general phase behavior in these materials resembles that of both higher molecular weight block copolymers and lower molecular weight nonionic surfactant solutions. Two of the block copolymers exhibited thermally induced order-order transitions and were studied in detail by small...

  20. Evaporation of droplets of surfactant solutions.

    Science.gov (United States)

    Semenov, Sergey; Trybala, Anna; Agogo, Hezekiah; Kovalchuk, Nina; Ortega, Francisco; Rubio, Ramón G; Starov, Víctor M; Velarde, Manuel G

    2013-08-13

    The simultaneous spreading and evaporation of droplets of aqueous trisiloxane (superspreader) solutions onto a hydrophobic substrate has been studied both experimentally, using a video-microscopy technique, and theoretically. The experiments have been carried out over a wide range of surfactant concentration, temperature, and relative humidity. Similar to pure liquids, four different stages have been observed: the initial one corresponds to spreading until the contact angle, θ, reaches the value of the static advancing contact angle, θad. Duration of this stage is rather short, and the evaporation during this stage can be neglected. The evaporation is essential during the next three stages. The next stage after the spreading, which is referred to herein as the first stage, takes place at constant perimeter and ends when θ reaches the static receding contact angle, θr. During the next, second stage, the perimeter decreases at constant contact angle θ = θr for surfactant concentration above the critical wetting concentration (CWC). The static receding contact angle decreases during the second stage for concentrations below CWC because the concentration increases due to the evaporation. During the final stage both the perimeter and the contact angle decrease. In what follows, we consider only the longest stages I and II. The developed theory predicts universal curves for the contact angle dependency on time during the first stage, and for the droplet perimeter on time during the second stage. A very good agreement between theory and experimental data has been found for the first stage of evaporation, and for the second stage for concentrations above CWC; however, some deviations were found for concentrations below CWC.

  1. Cold pearl surfactant-based blends.

    Science.gov (United States)

    Crombie, R L

    1997-10-01

    Pearlizing agents have been used for many years in cosmetic formulations to add a pearlescent effect. Cold pearl surfactant-based blends are mixtures of glycol stearates and surfactants which can be blended in the cold into a wide range of personal-care formulations to create a pearlescent lustre effect. Under controlled manufacturing conditions constant viscosities and crystalline characteristics can be obtained. The development of these blends has been driven by efforts to improve the economics of adding solid pearlizing agents directly into a hot mix formulation. This paper summarizes the history of pearlizers, describes their advantages and physical chemistry of the manufacturing process. Finally some suggestions for applications are given. Les agents nacrants sont utilises depuis de nombreuses annees dans les formulations cosmetiques pour ajouter un effet nacre. Les melanges a froid a base de tensioactif nacre sont des melanges de stearates de glycol et de tensioactifs qui peuvent etre melanges a froid dans une large gamme de formulations d'hygiene personnelle pour creer un effet de lustre nacre. On peut obtenir des viscosites et des proprietes cristallines constantes avec des conditions de fabrication maitrisees. Le developpement de ces melanges a ete porte par les efforts pour ameliorer les couts de l'ajout d'agents nacrants solides directement dans une formulation melangee de l'ajout d'agents nacrants solides directement dans une formulation melangee a chaud. Cet article resume l'histoire des agents nacrants, decrit leurs avantages et al physico-chimie du procede de fabrication. On emet a la fin cetaines suggestions d'applications.

  2. Structure and Conformational Dynamics of DMPC/Dicationic Surfactant and DMPC/Dicationic Surfactant/DNA Systems

    Directory of Open Access Journals (Sweden)

    Maciej Kozak

    2013-04-01

    Full Text Available Amphiphilic dicationic surfactants, known as gemini surfactants, are currently studied for gene delivery purposes. The gemini surfactant molecule is composed of two hydrophilic “head” groups attached to hydrophobic chains and connected via molecular linker between them. The influence of different concentrations of 1,5-bis (1-imidazolilo-3-decyloxymethyl pentane chloride (gemini surfactant on the thermotropic phase behaviour of 1,2-dimyristoyl-sn-glycero-3-phosphocholine (DMPC bilayers with and without the presence of DNA was investigated using Fourier transformed infrared (FTIR and circular dichroism (CD spectroscopies, small angle scattering of synchrotron radiation and differential scanning calorimetry. With increasing concentration of surfactant in DMPC/DNA systems, a disappearance of pretransition and a decrease in the main phase transition enthalpy and temperature were observed. The increasing intensity of diffraction peaks as a function of surfactant concentration also clearly shows the ability of the surfactant to promote the organisation of lipid bilayers in the multilayer lamellar phase.

  3. The importance of surfactant proteins-New aspects on macrophage phagocytosis.

    Science.gov (United States)

    Tschernig, Thomas; Veith, Nils T; Diler, Ebru; Bischoff, Markus; Meier, Carola; Schicht, Martin

    2016-11-01

    Surfactant and its components have multiple functions. The so called collectins are surfactant proteins which opsonize bacteria and improve pulmonary host defense via the phagocytosis and clearance of microorganisms and particles. In this special issue of the Annals of Anatomy a new surfactant protein, Surfactant Associated 3, is highlighted. As outlined in this mini review Surfactant Associated 3 is regarded as an enhancer of phagocytosis. In addition, the role played by SP-A is updated and open research questions raised.

  4. APPLICATION OF SURFACTANTS AS PULPING ADDITIVES IN SODA PULPING OF BAGASSE

    OpenAIRE

    2009-01-01

    The effects of several non-ionic commercial surfactants and their dosage on soda pulping and ECF bleaching of soda and soda-surfactant pulps of bagasse were investigated. The properties of bleachable pulps obtained with conventional soda and with soda-surfactants were studied and compared. The results showed application of surfactants during the soda pulping of bagasse decreased kappa number and improved the yield and brightness of resulting pulp. Using the surfactants reduced alkali consumpt...

  5. Surfactant nebulisation prevents the adverse effects of surfactant therapy on blood pressure and cerebral blood flow in rabbits with severe respiratory failure

    NARCIS (Netherlands)

    Dijk, PH; Heikamp, A; Oetomo, SB

    1997-01-01

    Objective: Surfactant replacement therapy for the neonatal respiratory distress syndrome has shown beneficial effects on lung function and survival. Recently, rapid fluctuations of haemodynamics and cerebral perfusion following surfactant instillation have beer, described and an association with the

  6. The adsorption of surfactant at the amorphous polymer solution interface

    CERN Document Server

    Gilchrist, V A

    2001-01-01

    Adsorption of surfactants onto amorphous polymers at the solid-solution interface is of direct relevance to many industrial sectors ranging from food, pharmaceuticals, paints, paper and photographic colour films. Although it is widely accepted that surfactants play the underpinning role in these applications, little is currently understood about the interactions between surfactants and polymeric materials at the molecular level. This lack of progress is mainly due to the inability of most existing techniques in probing this type of structural information at the wet interface. Specular neutron reflection (SNR) is a recently developed technique capable of detecting structural information with resolution down to a few angstroms (A). When combined with deuterium labeling, it is possible to distinguish the surfactant from the polymeric species at the interface. The aim of this work is to explore the appropriate experimental approach that utilizes the potential of neutron reflection to unravel molecular information...

  7. Graphene-philic surfactants for nanocomposites in latex technology.

    Science.gov (United States)

    Mohamed, Azmi; Ardyani, Tretya; Bakar, Suriani Abu; Brown, Paul; Hollamby, Martin; Sagisaka, Masanobu; Eastoe, Julian

    2016-04-01

    Graphene is the newest member of the carbon family, and has revolutionized materials science especially in the field of polymer nanocomposites. However, agglomeration and uniform dispersion remains an Achilles' heel (even an elephant in the room), hampering the optimization of this material for practical applications. Chemical functionalization of graphene can overcome these hurdles but is often rather disruptive to the extended pi-conjugation, altering the desired physical and electronic properties. Employing surfactants as stabilizing agents in latex technology circumvents the need for chemical modification allowing for the formation of nanocomposites with retained graphene properties. This article reviews the recent progress in the use of surfactants and polymers to prepare graphene/polymer nanocomposites via latex technology. Of special interest here are surfactant structure-performance relationships, as well as background on the roles surfactant-graphene interactions for promoting stabilization.

  8. FLUORINATED SURFACTANTS IN THE GREAT LAKES - YESTERDAY, TODAY, AND TOMORROW

    Science.gov (United States)

    Perfluorooctane surfactants have been reported in biota, water, and air samples worldwide. Despite these reports, the main environmental sources of these compounds remain undefined. As a presentation to the emerging chemicals workshop of the International Joint Commission on Grea...

  9. Experimental study on thermophoresis of colloids in aqueous surfactant solutions

    Science.gov (United States)

    Dong, Ruo-Yu; Zhou, Yi; Yang, Chun; Cao, Bing-Yang

    2015-12-01

    Thermophoresis refers to the motion of particles under a temperature gradient and it is one of the particle manipulation techniques. Regarding the thermophoresis of particles in liquid media, however, many open questions still remain, especially the role of the interfacial effect. This work reports on a systematic experimental investigation of surfactant effects, especially the induced interfacial effect, on the thermophoresis of colloids in aqueous solutions via a microfluidic approach. Two kinds of commonly used surfactants, sodium dodecyl sulfate (SDS) and cetyltrimethylammonium bromide (CTAB), are selected and the results show that from relatively large concentrations, the two surfactants can greatly enhance the thermophilic mobilities. Specifically, it is found that the colloid-water interfaces modified with more polar end groups can potentially lead to a stronger thermophilic tendency. Due to the complex effects of surfactants, further theoretical model development is needed to quantitatively describe the dependence of thermophoresis on the interface characteristics.

  10. Surfactant and adhesive formulations from alkaline biomass extracts

    Science.gov (United States)

    Baxter, Matthew

    This work studies the ability to produce effective surfactant and adhesive formulations using surface active biological material extracted from different biomass sources using alkaline extraction methods. Two urban waste biomass sources were used to produce surfactants, Return Activated Sludge (RAS), and solid Urban Refuse (UR). The third biomass source investigated was isolated mustard protein (MP). RAS and MP extracts were investigated for adhesive production. The results indicate that extracts from the waste biomass sources, RAS and UR, can be combined with a commercial surfactant, sodium dioctyl sulfosuccinate (AOT), to produce surfactants with low interfacial tensions against various oils. These highly surface-active formulations were shown to be useful in the removal of bitumen from contaminated sand. RAS and MP showed potential as protein-based wood adhesives. These sources were used in adhesive formulations to produce a strong bond strength under low-pressure, ambient pressing conditions.

  11. Efficient deacylation of N-acylimidazoles by functionalized surfactant micelles

    OpenAIRE

    Ihara, Yasuji; Nango, Mamoru; Koga, Joichi; ナンゴ, マモル; 南後, 守

    1989-01-01

    Hydroxylated surfactant micelles are powerful catalysts for the deacylation of N-acylimidazoles under neutral conditions; the deacylation rates of hydrophobia acylimidazoles are accelerated remarkably by functionalized micelles containing three hydroxy groups at the polar head.

  12. Tunable Oleo-Furan Surfactants by Acylation of Renewable Furans

    Energy Technology Data Exchange (ETDEWEB)

    Park, Dae Sung; Joseph, Kristeen E.; Koehle, Maura; Krumm, Christoph; Ren, Limin; Damen, Jonathan N.; Shete, Meera H.; Lee, Han Seung; Zuo, Xiaobing; Lee, Byeongdu; Fan, Wei; Vlachos, Dionisios G.; Lobo, Raul F.; Tsapatsis, Michael; Dauenhauer, Paul J.

    2016-11-23

    An important advance in fluid surface control was the amphiphilic surfactant comprised of coupled molecular structures (i.e. hydrophilic and hydrophobic) to reduce surface tension between two distinct fluid phases. However, implementation of simple surfactants has been hindered by the broad range of applications in water containing alkaline earth metals (i.e. hard water), which disrupt surfactant function and require extensive use of undesirable and expensive chelating additives. Here we show that sugar-derived furans can be linked with triglyceride-derived fatty acid chains via Friedel-Crafts acylation within single layer (SPP) zeolite catalysts. These alkylfuran surfactants independently suppress the effects of hard water while simultaneously permitting broad tunability of size, structure, and function, which can be optimized for superior capability for forming micelles and solubilizing in water.

  13. Deformation and stability of surfactant - or particle - laden drop

    Science.gov (United States)

    Brosseau, Quentin; Pradillo, Gerardo; Oberlander, Andrew; Vlahovska, Petia; SoftMech@Brown Team

    2015-11-01

    We present an experimental study of the behavior of a drop covered with insoluble surfactant or colloidal particles in a uniform DC electric field. Steady drop shapes, drop evolution upon application of the field, and drop relaxation after the field is turned off are observed for leaky dielectric fluids: Polybutadiene (PB), Silicon oil (PDMS), and Castor oil (CO). The surfactant is generated at the drop interface by reaction between end-functionalized PB and PDMS. The experimental data is compared with existing theoretical models for the steady shape of surfactant covered droplet, and adjusted models taking into account the presence of colloidal spheres with range of electrical properties. We will discuss the complex interplay of shape deformation, surfactant elasticity, particle redistribution, and interfacial charging in droplet electrohydrodynamics. Our results are important for understanding electrorheology of emulsions commonly found in the petroleum industry. We acknowledge grant NSF CBET 1437545 for funding.

  14. Polyelectrolyte surfactant aggregates and their deposition on macroscopic surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Voisin, David

    2002-07-01

    Oppositely charged surfactant and polyelectrolyte are present in hair shampoos and conditioners, together with particles (e.g. anti-dandruff agents for scalp) and droplets (e.g. silicone oil for the hair). These are normally formulated at high surfactant concentrations, beyond the flocculation region for the polyelectrolyte concentration used. However, on dilution with water, during application, flocs are formed which carry the particles and droplets to the scalp and hair. The addition of an anionic surfactant to an aqueous solution of cationic polyelectrolyte, at a given concentration, can lead to the formation of polyelectrolyte-surfactant 'particles', in which the surfactant 'binds' to the polyelectrolyte. This occurs from the critical association concentration (CAC), up to the surfactant concentration corresponding to maximum binding. Within this range of surfactant concentrations, the surfactant bound to the polyelectrolyte is thought to associate to form what might be termed 'internal micelles'. Each polyelectrolyte-surfactant particle in the region of the CAC, and just beyond, contains many polyelectrolyte chains, held together essentially by micelle bridges. These particles, however, remain net positively charged, and therefore stable. At the other end of the binding range of the surfactant, so many internal micelles are present that the polymer-surfactant particles are now net negatively charged. Indeed binding stops since no further micelles can be accommodated. Again, the particles are stable. However, there exists a range of surfactant concentrations, lying within the range referred to above, where the net charge is reduced sufficiently that the polymer-surfactant particles will flocculate to form much larger structures. The onset of this second range might be termed the 'critical flocculation concentration' (CFC), and the end, the 'critical stabilisation concentration' (CSC). In this work, the CFC and

  15. Defluorination of drinking water using surfactant modified zeolites ...

    African Journals Online (AJOL)

    Journal of Science and Technology (Ghana) ... by employing surfactant modified zeolites (SMZ) synthesized using locallyavailable kaolin material as precursor. ... The SEM showed the zeolite NaLSX crystals to be octahedrally shaped.

  16. Surfactants and the attachment of Pseudomonas aeruginosa to ...

    African Journals Online (AJOL)

    drinie

    2001-01-01

    Jan 1, 2001 ... lower surface tension and its ability to prevent microbial adhesion. White and ..... Special cell surface structures (e.g. fibrils or polymers) form strong ... WHITE GF and RUSSEL NJ (1992) Biodegradation of anionic surfactants.

  17. Nonlinear vibrational spectroscopy of surfactants at liquid interfaces

    Energy Technology Data Exchange (ETDEWEB)

    Miranda, Paulo B. [Univ. of California, Berkeley, CA (United States)

    1998-12-14

    Surfactants are widely used to modify physical and chemical properties of interfaces. They play an important role in many technological problems. Surfactant monolayer are also of great scientific interest because they are two-dimensional systems that may exhibit a very rich phase transition behavior and can also be considered as a model system for biological interfaces. In this Thesis, we use a second-order nonlinear optical technique (Sum-Frequency Generation - SFG) to obtain vibrational spectra of surfactant monolayer at Iiquidhapor and solid/liquid interfaces. The technique has several advantages: it is intrinsically surface-specific, can be applied to buried interfaces, has submonolayer sensitivity and is remarkably sensitive to the confirmational order of surfactant monolayers.

  18. (NLC-Effect of Surfactant Concentration on the Formulation Properties

    Directory of Open Access Journals (Sweden)

    Akram Pezeshki

    2014-12-01

    Conclusion: This study suggests that surfactant significantly influences the final product properties. Our findings may pave the way of researchers to focus on fortifying the beverages with various lipophilic nutraceuticals.

  19. Surface-enhanced Raman spectroscopy of surfactants on silver electrodes

    Energy Technology Data Exchange (ETDEWEB)

    Sun, Soncheng; Birke, R.L.; Lombardi, J.R. (City Univ. of New York, NY (USA))

    1990-03-08

    Surface-enhanced Raman spectroscopy (SERS) has been used to study different kinds of surfactants (cationic, anionic, and nonionic surfactants) adsorbed on a roughened Ag electrode. Spectral assignments are made for the SERS spectrum of cetylpyridinium chloride (CPC), and it is shown that the molecule is oriented with its pyridinium ring end-on at the electrode surface at potentials positive to the point of zero charge (pzc) on Ag.

  20. Structural studies of lamellar surfactant systems under shear

    DEFF Research Database (Denmark)

    Mortensen, K.

    2001-01-01

    Recent experimental studies on concentrated surfactant systems are reviewed. Particular attention is focused on the transformation from planar lamellar sheets to multilamellar vesicles. It is discussed whether both of these states are thermodynamic stable, or if the MLV is an artifact of shear...... induced factors. Recent studies includes the dependence on shear, and dependence on salt and cosurfactants, and thereby related lamellar defects. The review include moreover the demonstration that polymeric amphiphiles dramatically enhance the quality of classical surfactants. (C) 2001 Elsevier Science...

  1. Modification of Shape Oscillations of an Attached Bubble by Surfactants

    OpenAIRE

    Tihon J.; Vejražka J.; Vobecká L.

    2013-01-01

    Surface-active agents (surfactants, e.g. washing agents) strongly modifies properties of gas-liquid interface. We have carried out extensive experiments, in which we study effect of surfactants on the shape oscillations of a bubble, which is attached at a tip of a capillary. In the experiments, shape oscillations of a bubble are invoked by a motion of a capillary, to which the bubble is injected. Decaying oscillations are recorded and their frequency and damping are evaluated. By changing the...

  2. Green Cosmetic Surfactant from Rice: Characterization and Application

    OpenAIRE

    Ibrahim Hanno; Marisanna Centini; Cecilia Anselmi; Claudia Bibiani

    2015-01-01

    During recent years, microwave irradiation has been extensively used for performing green organic synthesis. The aim of this study was to synthesize, through a microwave-assisted irradiation process, a natural surfactant with O/W emulsifying properties. Our attention was focused on polyglycerol esters of fatty acids that are biocompatible and biodegradable non-ionic surfactants widely used in food and cosmetic products. The emulsifier was obtained using vegetable raw material from renewable s...

  3. Nanoparticle decoration with surfactants: Molecular interactions, assembly, and applications

    Science.gov (United States)

    Heinz, Hendrik; Pramanik, Chandrani; Heinz, Ozge; Ding, Yifu; Mishra, Ratan K.; Marchon, Delphine; Flatt, Robert J.; Estrela-Lopis, Irina; Llop, Jordi; Moya, Sergio; Ziolo, Ronald F.

    2017-02-01

    Nanostructures of diverse chemical nature are used as biomarkers, therapeutics, catalysts, and structural reinforcements. The decoration with surfactants has a long history and is essential to introduce specific functions. The definition of surfactants in this review is very broad, following its lexical meaning ;surface active agents;, and therefore includes traditional alkyl modifiers, biological ligands, polymers, and other surface active molecules. The review systematically covers covalent and non-covalent interactions of such surfactants with various types of nanomaterials, including metals, oxides, layered materials, and polymers as well as their applications. The major themes are (i) molecular recognition and noncovalent assembly mechanisms of surfactants on the nanoparticle and nanocrystal surfaces, (ii) covalent grafting techniques and multi-step surface modification, (iii) dispersion properties and surface reactions, (iv) the use of surfactants to influence crystal growth, as well as (v) the incorporation of biorecognition and other material-targeting functionality. For the diverse materials classes, similarities and differences in surfactant assembly, function, as well as materials performance in specific applications are described in a comparative way. Major factors that lead to differentiation are the surface energy, surface chemistry and pH sensitivity, as well as the degree of surface regularity and defects in the nanoparticle cores and in the surfactant shell. The review covers a broad range of surface modifications and applications in biological recognition and therapeutics, sensors, nanomaterials for catalysis, energy conversion and storage, the dispersion properties of nanoparticles in structural composites and cement, as well as purification systems and classical detergents. Design principles for surfactants to optimize the performance of specific nanostructures are discussed. The review concludes with challenges and opportunities.

  4. Effects of Surfactants on the Rate of Chemical Reactions

    Directory of Open Access Journals (Sweden)

    B. Samiey

    2014-01-01

    Full Text Available Surfactants are self-assembled compounds that depend on their structure and electric charge can interact as monomer or micelle with other compounds (substrates. These interactions which may catalyze or inhibit the reaction rates are studied with pseudophase, cooperativity, and stoichiometric (classical models. In this review, we discuss applying these models to study surfactant-substrate interactions and their effects on Diels-Alder, redox, photochemical, decomposition, enzymatic, isomerization, ligand exchange, radical, and nucleophilic reactions.

  5. Use of surfactants to control island size and density

    Energy Technology Data Exchange (ETDEWEB)

    Merrell, Jason; Liu, Feng; Stringfellow, Gerald B.

    2017-08-15

    Methods of controlling island size and density on an OMVPE growth film may comprise adding a surfactant at a critical concentration level, allowing a growth phase for a first period of time, and ending the growth phase when desired island size and density are achieved. For example, the island size and density of an OMVPE grown InGaN thin film may be controlled by adding an antimony surfactant at a critical concentration level.

  6. Surfactant Enhanced Microbial Degradation of JP-8 Contaminated Soil

    Science.gov (United States)

    1996-12-01

    Aromatics Xylenes Polycyclic Aromatics n-Alkanes Alkylbenzenes PAHs n-Alkenes Nitro-substituted Aromatics PNAs Phenols Halogenated Aliphatics Cycloalkanes...solubility has an apparent linear increase (Rosen, 1989:171). Solubilization occurs at a number of sites within a micelle (Figure 2.6): (1) the inner... Sulfonate (anionic). Each of these surfactants showed enhancement of biodegradation close to 90%, when compared to treatments without surfactant addition

  7. Interaction of Natural Dye (Allium cepa) with Ionic Surfactants

    OpenAIRE

    2013-01-01

    Allium cepa is a natural dye that has been extracted from onion skin with the help of soxhlet apparatus. The pigment in the dye pelargonidin was found to be 2.25%. The interaction of the dye with ionic surfactants, namely, cationic surfactant (cetyltrimethylammonium bromide) and anionic (sodium lauryl sulphate) has been studied by spectrophotometrically, conductivity, and surface tension measurements. The thermodynamic and surface parameters have been evaluated for the interaction process. Th...

  8. The promotion of functional recovery and nerve regeneration after spinal cord injury by lentiviral vectors encoding Lingo-1 shRNA delivered by Pluronic F-127.

    Science.gov (United States)

    Wu, Hong-Fu; Cen, Jing-Sheng; Zhong, Qian; Chen, Luming; Wang, Jue; Deng, David Y B; Wan, Yong

    2013-02-01

    Lingo-1 is selectively expressed on both oligodendrocytes and neurons in the central nervous system (CNS) and serves as a key negative regulator of nerve regeneration, implying a therapeutic target for spinal cord injury (SCI). Here we described a strategy to knock-down Lingo-1 expression in vivo using lentiviral vectors encoding Lingo-1 short harpin interfering RNA (shRNA) delivered by Pluronic F-127 (PF-127) gel, a non-cytotoxic scaffold and gene delivery carrier, after the complete transection of the T10 spinal cord in adult rats. We showed administration of PF-127 encapsulating Lingo-1 shRNA lentiviral vectors efficiently down-regulated the expression of Lingo-1, and exhibited transduction efficiency comparable to using vectors alone in oligodendrocyte culture in vitro. Furthermore, similar silencing effects and higher transfection efficiency were observed in vivo when Lingo-1 shRNA was co-delivered to the injured site by PF-127 gel with lower viral concentrations. Cografting of gel and Lingo-1 RNAi significantly promoted functional recovery and nerve regeneration, enhanced neurite outgrowth and synapses formation, preserved myelinated axons, and induced the proliferation of glial cells. In addition, the combined implantation also improved neuronal survival and inhibited cell apoptosis, which may be associated with the attenuation of endoplasmic reticulum (ER) stress after SCI. Together, our data indicated that delivering Lingo-1 shRNA by gel scaffold was a valuable treatment approach to SCI and PF-127 delivery of viral vectors to the spinal cord may provide strategy to study and develop therapies for SCI.

  9. Hierarchical porous silver metal using Pluronic F-127 and graphene oxide as reinforcing agents for the reduction of o-nitroaniline to 1, 2-benzenediamine

    Science.gov (United States)

    Bano, Mustri; Ahirwar, Devendra; Thomas, Molly; Sheikh, Mehraj Ud Din; Khan, Farid

    2017-04-01

    An elegant method is used to prepare silver monoliths with Pluronic F-127(F-127) as sacrificial template by modified sol-gel method. Si nanoparticles (SiNPs) and graphene oxide (GO) are added in situ to Ag/F-127 hydrogel for the reduction of ο-nitroaniline (ο-NA) to 1, 2-benzenediamine. Fourier Transform Infrared Spectroscopy (FT-IR), Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), Thermogravimetric analysis (TGA), Raman Spectroscopy, Powder X-Ray Diffraction (PXRD) analysis and Brunauer-Emmett-Teller (BET) Nitrogen adsorption techniques were used for characterization of monoliths. An epoch-making catalytic activity of Ag/F-127/GO monoliths is observed in the reduction of ο-NA to 1, 2-benzenediamine in presence of NaBH4 in aqueous media. The catalyst Ag/F-127/GO took only 2 min which is the minimum time reported so far with significant rate constant claimed itself a leading catalyst for the reduction of ο-NA to 1,2-benzenediamine. Pseudo first order rate constant (k) and Turn over frequency (TOF) values are 0.231 min-1 and 30.053×1019 molecules min-1 respectively suggest that the catalyst has industrial importance. Recyclability and stability of Ag/F-127/GO catalyst are studied successfully up to 10 cycles. Energy of activation (Ea), and thermodynamic parameters viz. activation enthalpy (ΔH≠), activation Gibbs free energy (ΔG≠), and entropy of activation (ΔS≠) were also ascertained. Catalytic activities of Ag/F-127, Ag/F-127/Dextran, Ag/F-127/Trimethylbenzene (TMB), Ag/F-127/SiNPs, and Ag/F-127/Si/GO monoliths were also studied.

  10. Axenizing and Culturing Endomigratory Plant-Parasitic Nematodes using Pluronic F127, Including its Effects, on Population Dynamics of Pratylenchus penetrans.

    Science.gov (United States)

    Ko, M P; Schmitt, D P; Sipes, B S

    1996-03-01

    A non-chemical technique for surface sterilizing plant-parasitic nematodes for aseptic cultures is described. The method is most applicable to nematodes with active migratory infective stages and requires only a few starting specimens. Rate of achieving a primary aseptic culture with the technique ranged from 60%-100% depending on the conditions of the specimens collected for culturing. Aseptic cultures of species of Meloidogyne, Rotylenchuluz, Pratylenchus, and Radopholus initiated with the method remained contamination-free after 12 months of maintenance in tomato root explant or alfalfa callus cultures. Further studies of Pluronic F127, a polyol gel medium employed in the technique to confine the spread of contaminating bacteria or fungi associated with the nematodes, showed that the polyol gel was a suitable support medium for culturing corn root explant, alfalfa callus tissues, and consequently Pratylenchus species including P. agilis, P. brachyurus, P. scribneri, and P. penetrans. During the course of 10 months, P. penetrans reared in polyol-base medium followed a standard biological growth curve, multiplied to a higher population density, maintained a similar female-to-male ratio, and possessed a similar tendency to reside inside or outside host tissues as did P. penetrans reared in agar-base medium. The percentages of P. penetrans juveniles in the sub-populations residing outside or inside the host tissues reared in polyol-base medium also were similar to and fluctuated temporally in like manner as those reared in agar-base medium. Members of these sub-populations from the polyol- or agar-base were equally infective and reproductive after 9 months of culturing.

  11. A simplified treatment of surfactant effects on cloud drop activation

    Directory of Open Access Journals (Sweden)

    T. Raatikainen

    2010-07-01

    Full Text Available Dissolved surface active species, or surfactants, have a tendency to partition to solution surface and thereby decrease solution surface tension. Activating cloud droplets have large surface-to-volume ratios, and the amount of surfactant molecules in them is limited. Therefore, unlike with macroscopic solutions, partitioning to the surface can effectively deplete the droplet interior of surfactant molecules.

    Surfactant partitioning equilibrium for activating cloud droplets can be solved numerically from a group of equations. This can be a problem when surfactant effects are examined by using large-scale cloud models. Namely, computing time increases significantly due to the partitioning calculations done in the lowest levels of nested iterations.

    The purpose of this paper is to present analytical equations for surfactant partitioning equilibrium. Some simplifications are needed in deriving the equations, but the numerical errors caused by the simplifications are shown to be very minor. In addition, computing time is decreased roughly by an order of magnitude.

  12. Optimization and mechanism of surfactant accelerating leaching test

    Institute of Scientific and Technical Information of China (English)

    艾纯明; 吴爱祥; 王贻明; 侯春来

    2016-01-01

    To solve the problem of slow leaching speed of copper, surfactant was added into lixivium as leaching agent in the experiment. Based on physical chemistry and seepage flow mechanics, the leaching mechanics of surfactant was analyzed. The solution surface tension and surfactant adsorbing on the surface of ore have a significant impact on the surface wetting effect. With leaching rate for response, the study screened out three main factors by Plackett-Burman design method: the sulfuric acid concentration, surfactant concentration and temperature. Among these three factors, the surfactant concentration is the most important contributor to leaching rate. After obtaining the experiment center by the steepest ascent experiment, a continuous variable surface model was built by response surface methodology. By solving quadratic polynomial equation, optimal conditions for leaching were finally obtained as follows:the sulfuric acid concentration was 60 g/L, the surfactant concentration was 0.00914 mol/L, and the temperature was 45 °C. The leaching rate was 66.81%in the optimized leaching conditions, which was close to the predicted value, showing that regression result was good.

  13. Physicochemical treatments of anionic surfactants wastewater: Effect on aerobic biodegradability.

    Science.gov (United States)

    Aloui, Fathi; Kchaou, Sonia; Sayadi, Sami

    2009-05-15

    The effect of different physicochemical treatments on the aerobic biodegradability of an industrial wastewater resulting from a cosmetic industry has been investigated. This industrial wastewater contains 11423 and 3148mgL(-1) of chemical oxygen demand (COD) and anionic surfactants, respectively. The concentration of COD and anionic surfactants were followed throughout the diverse physicochemical treatments and biodegradation experiments. Different pretreatments of this industrial wastewater using chemical flocculation process with lime and aluminium sulphate (alum), and also advanced oxidation process (electro-coagulation (Fe and Al) and electro-Fenton) led to important COD and anionic surfactants removals. The best results were obtained using electro-Fenton process, exceeding 98 and 80% of anionic surfactants and COD removals, respectively. The biological treatment by an isolated strain Citrobacter braakii of the surfactant wastewater, as well as the pretreated wastewater by the various physicochemical processes used in this study showed that the best results were obtained with electro-Fenton pretreated wastewater. The characterization of the treated surfactant wastewater by the integrated process (electro-coagulation or electro-Fenton)-biological showed that it respects Tunisian discharge standards.

  14. Solubilization isotherms of aromatic solutes in surfactant aggregates

    Energy Technology Data Exchange (ETDEWEB)

    Gadelle, F.; Koros, W.J.; Schechter, R.S. (Univ. of Texas, Austin, TX (United States). Dept. of Chemical Engineering)

    1995-03-01

    Several factors affecting solubilization of aromatic solutes in surfactant micelles have been investigated. Solubilization isotherms of benzene, toluene, and chlorobenzene in various aqueous micellar solutions were determined using head space gas chromatography. Cationic surfactants such as cetylpyridinium chloride or cetyltrimethylammonium bromide present high solubilization capacities. Comparable anionic surfactants exhibit lower solubilization and a greater tendency to precipitate. It was observed that nonionic surfactants show high solubilization on a molar basis. Solubilization in mixed cationic-anionic micelles was also investigated. It also appears that the molecular size of the solute determines the extent of the solubilization. Finally, the shape of the different isotherms indicates that knowing the amount solubilized at saturation of the micellar solution is not sufficient to estimate solubilization at solute concentrations lower than the solute aqueous solubility. Solubilization of organics in surfactant micelles is of major importance in many applications. One new application is micellar-enhanced ultrafiltration. Another application of interest is the surfactant-enhanced aquifer remediation, a process in which a micellar aqueous solution is flushed into contaminated groundwaters to enhance recovery of pollutants by micellar solubilization.

  15. Postdeposition dispersion of aerosol medications using surfactant carriers.

    Science.gov (United States)

    Marcinkowski, Amy L; Garoff, Stephen; Tilton, Robert D; Pilewski, Joseph M; Corcoran, Timothy E

    2008-12-01

    Inhaled aerosol drugs provide a means of directly treating the lungs; however, aerosol deposition and drug distribution can be nonuniform, especially in obstructive lung disease. We hypothesize that surfactant-based aerosol carriers will disperse medications over airway surfaces after deposition through surface tension driven flows, increasing dose uniformity and improving drug distribution into underventilated regions. We considered saline and surfactant aerosol delivery via cannula onto several model airway surfaces including porcine gastric mucus (PGM) and both cystic fibrosis (CF) and non-CF human bronchial epithelial cells (HBEs). Fluorescent dye and microspheres (d = 100 nm, 1 mum) were used to qualitatively and quantitatively assess postdeposition dispersion. Aerosol volume median diameters were in the 1-4 mum range. The tested surfactants included sodium dodecyl sulfate (SDS), cetyl trimethyl ammonium bromide (CTAB), tyloxapol, and calfactant. All surfactants tested on PGM (tyloxapol, calfactant, SDS, and CTAB) significantly increased dispersion area versus saline with all markers (2-20-fold increases; all p surfactants tested on CF HBEs (tyloxapol and calfactant) significantly increased dispersion area versus saline with all markers (1.6-4.1-fold increases; all p Surfactant carriers enhanced dispersion after aerosol deposition onto model airway surfaces, and may improve the efficacy of inhaled preparations such as inhaled antibiotics for cystic fibrosis.

  16. [Acute toxicity of different type pesticide surfactants to Daphnia magna].

    Science.gov (United States)

    Li, Xiu-huan; Li, Hua; Chen, Cheng-yu; Li, Jian-tao; Liu, Feng

    2013-08-01

    By using the standard test methods in Experimental Guideline for Environmental Safety Evaluation of Chemical Pesticide to aquatic organisms, a comparative study was conducted on the acute toxicity of 39 nonionic, 6 anionic, and 3 cationic surfactants to Daphnia magna. The acute toxicity of three cationic surfactants 1427, 1227 and C8-10 to D. magna belonged to virulent level, and the toxicity of 1427 was the highest, with the EC50 value being 0.97 x 10(-2) mg x L(-1). The acute toxicity of nonionic surfactants polyoxyethylene ether castor oil EL, Tween, and Span emulsifiers belonged to low level, but the toxicity of alkylphenol polyoxyethylene ether and fatty alcohol polyoxyethylene ether surfactants was relatively high, of which, AEO-7 and AEO-5 displayed high toxicity, with the EC50 value being 0.82 and 0.97 mg x L(-1), respectively. In these surfactants, the more liposolubility, the higher the toxicity was. Most of the anionic surfactants were medium in toxicity, but the acute toxicity of NNO belonged to high toxicity, with the EC50 value being 0.17 mg x L(-1).

  17. Dynamic surface tension of surfactant TA: experiments and theory.

    Science.gov (United States)

    Otis, D R; Ingenito, E P; Kamm, R D; Johnson, M

    1994-12-01

    A bubble surfactometer was used to measure the surface tension of an aqueous suspension of surfactant TA as a function of bubble area over a range of cycling rates and surfactant bulk concentrations. Results of the surface tension-interfacial area loops exhibited a rich variety of phenomena, the character of which varied systematically with frequency and bulk concentration. A model was developed to interpret and explain these data and for use in describing the dynamics of surface layers under more general circumstances. Surfactant was modeled as a single component with surface tension taken to depend on only the interfacial surfactant concentration. Two distinct mechanisms were considered for the exchange of surfactant between the bulk phase and interface. The first is described by a simple kinetic relationship for adsorption and desorption that pertains only when the interfacial concentration is below its maximum equilibrium value. The second mechanism is "squeeze-out" by which surfactant molecules are expelled from an interface compressed past a maximum packing state. The model provided good agreement with experimental measurements for cycling rates from 1 to 100 cycles/min and for bulk concentrations between 0.0073 and 7.3 mg/ml.

  18. Evaluation and management of inherited disorders of surfactant metabolism

    Institute of Scientific and Technical Information of China (English)

    Aaron Hamvas

    2010-01-01

    Objective To review the pathophysiology, evaluation, management, and outcomes of children with inherited disorders of surfactant metabolism due to mutations in the genes encoding surfactant proteins-B or -C(SFTPB, SFTPC), ATP binding cassette member A3 (ABCA3), and thyroid transcription factor (NKX2.1).Data sources Review of the literature, previous work from the author's and collaborators' laboratories, St. Louis Children's Hospital Lung Transplant Database.Study selection Key articles in the field, author's work.Results Inherited disorders of surfactant metabolism present as acute, severe respiratory dysfunction in the neonatal period (SFTPB, ABCA3, NKX2.1) or as chronic respiratory insufficiency in later infancy and childhood which is of variable onset, severity, and course (SFTPC, ABCA3, NKX2.1). Diagnosis is established with sequencing the relevant genes; lung biopsy with electron microscopy is a useful adjunct. For surfactant protein-B and ABCA3 deficiency presenting with acute neonatal disease, treatment options are limited to lung transplantation or compassionate care. For the more chronic presentations of surfactant protein-C, ABCA3, and NKX2.1 associated disease, the natural history is variable and therefore individualized, supportive care is appropriate,Conclusions Inherited disorders of surfactant metabolism are rare, but informative diseases that provide unique opportunities for understanding mechanisms of respiratory disease in newborns and children.

  19. A systems approach to mapping transcriptional networks controlling surfactant homeostasis

    Directory of Open Access Journals (Sweden)

    Dave Vrushank

    2010-07-01

    Full Text Available Abstract Background Pulmonary surfactant is required for lung function at birth and throughout life. Lung lipid and surfactant homeostasis requires regulation among multi-tiered processes, coordinating the synthesis of surfactant proteins and lipids, their assembly, trafficking, and storage in type II cells of the lung. The mechanisms regulating these interrelated processes are largely unknown. Results We integrated mRNA microarray data with array independent knowledge using Gene Ontology (GO similarity analysis, promoter motif searching, protein interaction and literature mining to elucidate genetic networks regulating lipid related biological processes in lung. A Transcription factor (TF - target gene (TG similarity matrix was generated by integrating data from different analytic methods. A scoring function was built to rank the likely TF-TG pairs. Using this strategy, we identified and verified critical components of a transcriptional network directing lipogenesis, lipid trafficking and surfactant homeostasis in the mouse lung. Conclusions Within the transcriptional network, SREBP, CEBPA, FOXA2, ETSF, GATA6 and IRF1 were identified as regulatory hubs displaying high connectivity. SREBP, FOXA2 and CEBPA together form a common core regulatory module that controls surfactant lipid homeostasis. The core module cooperates with other factors to regulate lipid metabolism and transport, cell growth and development, cell death and cell mediated immune response. Coordinated interactions of the TFs influence surfactant homeostasis and regulate lung function at birth.

  20. Barrier or carrier? Pulmonary surfactant and drug delivery.

    Science.gov (United States)

    Hidalgo, Alberto; Cruz, Antonio; Pérez-Gil, Jesús

    2015-09-01

    To consider the lung as a target for drug delivery and to optimise strategies directed at the pulmonary route, it is essential to consider the role of pulmonary surfactant, a thin lipid-protein film lining the respiratory surface of mammalian lungs. Membrane-based surfactant multilayers are essential for reducing the surface tension at the respiratory air-liquid interface to minimise the work of breathing. Different components of surfactant are also responsible for facilitating the removal of potentially pathological entities such as microorganisms, allergens or environmental pollutants and particles. Upon inhalation, drugs or nanoparticles first contact the surfactant layer, and these interactions critically affect their lifetime and fate in the airways. This review summarises the current knowledge on the possible role and effects of the pulmonary surfactant system in drug delivery strategies. It also summarises the evidence that suggests that pulmonary surfactant is far from being an insuperable barrier and could be used as an efficient shuttle for delivering hydrophobic and hydrophilic compounds deep into the lung and the organism.