On the Preparation of Working Standards for Gamma-Ray Spectrometry

International Nuclear Information System (INIS)

Durasevic, M.; Kandic, A.; Milosevic, Z.; Seslak, B.; Vukanac, I.

2013-01-01

In the Laboratory for Radionuclide Metrology at Vinca Institute, activity concentration measurements are routinely performed and numerous calibration standards are required. Thus, a variety of calibration standards whose measurement geometry and chemical composition and density are similar to those of the measured samples were prepared. The standardized solutions of a common mixture of gamma-emitting radionuclides (241Am, 109Cd, 139Ce, 57Co, 60Co,137Cs, 203Hg, 113Sn, 85Sr, 88Y and 210Pb) purchased at the Czech Metrological Institute were used to prepare working standards for efficiency and energy calibration of gamma-ray semiconductor HPGe spectrometer in accordance with the IAEA recommendations. Calibration standards were prepared in different geometries (PVC cylindrical boxes, Marinelly beakers and PVC cylindrical bottles) and with various matrices (mineralized grass, activated carbon, surface soil, water, sand and ached filter paper). The matrix materials were spiked by using the activated carbon as the activity carrier, and homogenized mechanically. A comprehensive review of the procedures and techniques used for working standard preparation is presented in this paper.(author)

Calibration of surface roughness standards

DEFF Research Database (Denmark)

Thalmann, R.; Nicolet, A.; Meli, F.

2016-01-01

organisations. Five surface texture standards of different type were circulated and on each of the standards several roughness parameters according to the standard ISO 4287 had to be determined. 32 out of 395 individual results were not consistent with the reference value. After some corrective actions...

Skin and surface lead contamination, hygiene programs, and work practices of bridge surface preparation and painting contractors.

Science.gov (United States)

Virji, M Abbas; Woskie, Susan R; Pepper, Lewis D

2009-02-01

A 2005 regulatory review of the lead in construction standard by the Occupational Safety and Health Administration (OSHA) noted that alternative pathways of exposure can be as significant as inhalation exposure and that noncompliance with the standard pertaining to hygiene facilities and practices was the second most commonly violated section of the standard. Noncompliance with provisions of the standard and unhealthy work and hygiene practices likely increase the likelihood of take-home lead via contaminated clothing, automobiles, and skin, thus contributing to elevated blood lead levels (BLL) among construction workers and their family members. We performed a cross-sectional study of bridge painters working for small contractors in Massachusetts to investigate causes of persistent elevated BLLs and to assess lead exposures. Thirteen work sites were evaluated for a 2-week period during which surface and skin wipe samples were collected and qualitative information was obtained on personal hygiene practices, decontamination and hand wash facilities, and respiratory protection programs. Results showed lead contamination on workers' skin, respirators, personal automobiles, and the decontamination unit, indicating a significant potential for take-home lead exposure. Overall, the geometric mean (GM) skin lead levels ranged from 373 microg on workers' faces at end of shift to 814 microg on hands at break time. The overall GM lead level inside respirators was 143 microg before work and 286 microg after work. Lead contamination was also present inside workers' personal vehicles as well as on surfaces inside the clean side of the decontamination unit. Review of the respiratory protection programs, work site decontamination and hand wash facilities, and personal hygiene practices indicated that these factors had significant impact on skin and surface contamination levels and identified significant opportunities for improving work site facilities and personal practices

Surface soil contamination standards

International Nuclear Information System (INIS)

Boothe, G.F.

1979-01-01

The purpose of this document is to define surface soil contamination limits for radioactive materials below which posting, restrictions and environmental controls are not necessary in order to protect personnel and the environment. The standards can also be used to determine if solid waste or other material is contaminated relative to disposal requirements. The derivation of the standards is given

Experimental standard molar enthalpies of formation of some methylbenzenediol isomers

International Nuclear Information System (INIS)

Ribeiro da Silva, Manuel A.V.; Lobo Ferreira, Ana I.M.C.

2009-01-01

The present work is part of a research program on the energetics of formation of alkyl substituted benzenediols, aiming the study of the enthalpic effect of the introduction of methyl substituents into benzenediols. In this work we present the results of the thermochemical research on 2-methylresorcinol, 3-methylresorcinol, 4-methylresorcinol, and methylhydroquinone. The standard (p 0 =0.1MPa) molar enthalpies of formation, in the crystalline phase, at T = 298.15 K, of the compounds mentioned above were derived from their standard massic energies of combustion, measured by static-bomb combustion calorimetry, while the standard molar enthalpies of sublimation of those compounds were obtained by the temperature dependence of their vapour pressures determined by the Knudsen effusion technique. From experimental values, the standard molar enthalpies of formation of the studied methylbenzenediols in the gaseous phase, at T = 298.15 K were then derived. The results are interpreted in terms of structural contributions to the energetics of the substituted benzenediols and compared with the same parameters estimated from the Cox Scheme. Moreover, the standard (p 0 =0.1MPa) molar enthalpies, entropies, and Gibbs energies of sublimation, at T = 298.15 K, were derived for the four isomers of methylbenzenediols.

Effects of electromyographic and mechanomyographic biofeedback on upper trapezius muscle activity during standardized computer work

DEFF Research Database (Denmark)

Madeleine, Pascal; Vedsted, Pernille; Blangsted, Anne Katrine

2006-01-01

The purpose of this laboratory study was to investigate the effects of surface electromyography (EMG)- and mechanomyography (MMG)-based audio and visual biofeedback during computer work. Standardized computer work was performed for 3 min with/without time constraint and biofeedback in a randomize...... alternative to EMG in ergonomics. A lowering of the trapezius muscle activity may contribute to diminish the risk of work related musculoskeletal disorders development.......The purpose of this laboratory study was to investigate the effects of surface electromyography (EMG)- and mechanomyography (MMG)-based audio and visual biofeedback during computer work. Standardized computer work was performed for 3 min with/without time constraint and biofeedback in a randomized......) values as well as the work performance in terms of number of completed graph/mouse clicks/errors, the rating of perceived exertion (RPE) and the usefulness of the biofeedback were assessed. The duration of muscle activity above the threshold was significantly lower with MMG compared with EMG as source...

Ab initio and work function and surface energy anisotropy of LaB6

NARCIS (Netherlands)

Uijttewaal, M. A.; de Wijs, G. A.; de Groot, R. A.

2006-01-01

Lanthanum hexaboride is one of the cathode materials most used in high-power electronics technology, but the many experimental results do not provide a consistent picture of the surface properties. Therefore, we report the first ab initio calculations of the work functions and surface energies of

Work surface for soluble plutonium

International Nuclear Information System (INIS)

Silver, G.L.

2005-01-01

A three-dimensional work surface for aqueous plutonium is illustrated. It is constructed by means of estimating work as a function of the ambient pH and redox potential in a plutonium solution. The surface is useful for illustrating the chemistry of disproportionation reactions. Work expressions are easier to use than work integrals. (author)

30 CFR 71.500 - Sanitary toilet facilities at surface work sites; installation requirements.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Sanitary toilet facilities at surface work sites; installation requirements. 71.500 Section 71.500 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY HEALTH STANDARDS-SURFACE COAL MINES AND...

40 CFR 63.306 - Work practice standards.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 9 2010-07-01 2010-07-01 false Work practice standards. 63.306 Section 63.306 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED... for Coke Oven Batteries § 63.306 Work practice standards. (a) Work practice plan. On or before...

Experimental investigation on water quality standard of Yangtze River water source heat pump.

Science.gov (United States)

Qin, Zenghu; Tong, Mingwei; Kun, Lin

2012-01-01

Due to the surface water in the upper reaches of Yangtze River in China containing large amounts of silt and algae, high content of microorganisms and suspended solids, the water in Yangtze River cannot be used for cooling a heat pump directly. In this paper, the possibility of using Yangtze River, which goes through Chongqing, a city in southwest China, as a heat source-sink was investigated. Water temperature and quality of the Yangtze River in the Chongqing area were analyzed and the performance of water source heat pump units in different sediment concentrations, turbidity and algae material conditions were tested experimentally, and the water quality standards, in particular surface water conditions, in the Yangtze River region that adapt to energy-efficient heat pumps were also proposed. The experimental results show that the coefficient of performance heat pump falls by 3.73% to the greatest extent, and the fouling resistance of cooling water in the heat exchanger increases up to 25.6% in different water conditions. When the sediment concentration and the turbidity in the river water are no more than 100 g/m3 and 50 NTU respectively, the performance of the heat pump is better, which can be used as a suitable river water quality standard for river water source heat pumps.

Non-standard work schedules, gender, and parental stress

Directory of Open Access Journals (Sweden)

Mariona Lozano

2016-02-01

Full Text Available Background: Working non-standard hours changes the temporal structure of family life, constraining the time that family members spend with one another and threatening individuals' well-being. However, the empirical research on the link between stress and non-standard schedules has provided mixed results. Some studies have indicated that working non-standard hours is harmful whereas others have suggested that working atypical hours might facilitate the balance between family and work. Moreover, there is some evidence that the association between stress and non-standard employment has different implications for men and women. Objective: This paper examines the association between non-standard work schedules and stress among dual-earner couples with children. Two research questions are addressed. First, do predictability of the schedule and time flexibility moderate the link between non-standard work hours and stress? Second, do non-standard schedules affect men's and women's perceptions of stress differently? Methods: We use a sample of 1,932 working parents from the Canadian 2010 General Social Survey, which includes a time-use diary. A sequential logit regression analysis stratified by gender is employed to model two types of result. First, we estimate the odds of being stressed versus not being stressed. Second, for all respondents feeling stressed, we estimate the odds of experiencing high levels versus moderate levels of stress. Results: Our analysis shows that the link between non-standard working hours and perceived stress differs between mothers and fathers. First, fathers with non-standard schedules appear more likely to experience stress than those working standard hours, although the results are not significant. Among mothers, having a non-standard schedule is associated with a significantly lower risk of experiencing stress. Second, the analysis focusing on the mediating role of flexibility and predictability indicates that

Synchronous Surface Pressure and Velocity Measurements of standard model in hypersonic flow

Directory of Open Access Journals (Sweden)

Zhijun Sun

2018-01-01

Full Text Available Experiments in the Hypersonic Wind tunnel of NUAA(NHW present synchronous measurements of bow shockwave and surface pressure of a standard blunt rotary model (AGARD HB-2, which was carried out in order to measure the Mach-5-flow above a blunt body by PIV (Particle Image Velocimetry as well as unsteady pressure around the rotary body. Titanium dioxide (Al2O3 Nano particles were seeded into the flow by a tailor-made container. With meticulous care designed optical path, the laser was guided into the vacuum experimental section. The transient pressure was obtained around model by using fast-responding pressure-sensitive paint (PSPsprayed on the model. All the experimental facilities were controlled by Series Pulse Generator to ensure that the data was time related. The PIV measurements of velocities in front of the detached bow shock agreed very well with the calculated value, with less than 3% difference compared to Pitot-pressure recordings. The velocity gradient contour described in accord with the detached bow shock that showed on schlieren. The PSP results presented good agreement with the reference data from previous studies. Our work involving studies of synchronous shock-wave and pressure measurements proved to be encouraging.

Standard reference data for the air-liquid and vapor-liquid surface tension of benzene

Czech Academy of Sciences Publication Activity Database

Součková, Monika; Klomfar, Jaroslav; Pátek, Jaroslav

2013-01-01

Roč. 356, October (2013), s. 329-337 ISSN 0378-3812 R&D Projects: GA ČR GA101/09/0010 Institutional support: RVO:61388998 Keywords : benzene * surface tension * experimental data * standard reference data Subject RIV: BJ - Thermodynamics Impact factor: 2.241, year: 2013 http://www.sciencedirect.com/science/article/pii/S0378381213004196

An orbital-overlap model for minimal work functions of cesiated metal surfaces

International Nuclear Information System (INIS)

Chou, Sharon H; Bargatin, Igor; Howe, Roger T; Voss, Johannes; Vojvodic, Aleksandra; Abild-Pedersen, Frank

2012-01-01

We introduce a model for the effect of cesium adsorbates on the work function of transition metal surfaces. The model builds on the classical point-dipole equation by adding exponential terms that characterize the degree of orbital overlap between the 6s states of neighboring cesium adsorbates and its effect on the strength and orientation of electric dipoles along the adsorbate-substrate interface. The new model improves upon earlier models in terms of agreement with the work function-coverage curves obtained via first-principles calculations based on density functional theory. All the cesiated metal surfaces have optimal coverages between 0.6 and 0.8 monolayers, in accordance with experimental data. Of all the cesiated metal surfaces that we have considered, tungsten has the lowest minimum work function, also in accordance with experiments.

Experimental Comparison of the Tribological Properties of Selected Surfaces Created by Thermal Spraying Technology

Directory of Open Access Journals (Sweden)

František Tóth

2016-01-01

Full Text Available The scientific article titled “Experimental comparison of the tribological properties of selected surfaces created by thermal spraying technology” deals with the surface condition of selected pairs working within the mixed friction before and after experimental tests. Based on the chosen methodology, the experimental tests were performed on the Tribotestor M’06 testing machine. The ecological oil MOGUL HEES 46 (manufactured by Paramo was used as a lubricant. The tests were performed on selected material pairs. The first friction element was a shaft of steel 14 220. The second friction element was a steel plate of steel 11 373 with a friction surface created by two materials, i.e. CuSn10 and NP 40. The results are statistically elaborated and illustrated in figures and tables.

Towards a public, standardized, diagnostic benchmarking system for land surface models

Directory of Open Access Journals (Sweden)

G. Abramowitz

2012-06-01

Full Text Available This work examines different conceptions of land surface model benchmarking and the importance of internationally standardized evaluation experiments that specify data sets, variables, metrics and model resolutions. It additionally demonstrates how essential the definition of a priori expectations of model performance can be, based on the complexity of a model and the amount of information being provided to it, and gives an example of how these expectations might be quantified. Finally, the Protocol for the Analysis of Land Surface models (PALS is introduced – a free, online land surface model benchmarking application that is structured to meet both of these goals.

Establishment of carcinoembryonic antigen working standard for immunoassay

International Nuclear Information System (INIS)

Xu Ligen; Sun Youxiang; Jiao Yan

2001-01-01

The author is to prepare the working standard of carcinoembryonic antigen (CEA) for immunoassay and determine its potency. CEA solution of 320 μg/L was prepared from purified CEA solution of 4.6 mg/L and 1% human albumin solution buffered with 50 mmol/L sodium phosphate, pH7.4. This solution was distributed in an aliquot of 0.5 mL (160 ng per ampoule) and lyophilized. The potency of CEA working standard, in terms of present standard of CEA RIA and IRMA kits made by Chinese manufacturers and in terms of 1st IRP CEA HUMAN 73/601 supplied by WHO, has been determined. Mean immunological potency of the working standard is 163 ng per ampoule with confident limit of 159-168 ng per ampoule at 95% probability level. Test of parallelism of dose-response curve for the working standard to that for 1st IRP CEA HUMAN 73/601 has been passed. CEA working standard is suitable to the kits standard for CEA radioimmunoassay and immunoradiometric assay

Discussion on enterprise technical standard management work

International Nuclear Information System (INIS)

Li Xinyou

2010-01-01

The technical standard management is an important part of enterprise information work, also the basis of enterprise standardization work. Only by rational and orderly management, can it exert maximum effectiveness, provide reliable support for the production and business of enterprise. (author)

CORROSION AND SURFACE PROTECTION IN MACHINE MATERIALS FRICTION HAVE DIFFERENT SURFACE PAIRS EXPERIMENTAL INVESTIGATION OF FACTORS

Directory of Open Access Journals (Sweden)

Senai YALCINKAYA

2017-05-01

Full Text Available Friction force, normal force, linear change. The normal force varies with the loads on the friction object. In order to determine the friction force and the friction coefficient, the friction object and the friction speed are used. The experimental work was carried out in three stages. In the first stage, the effect of normal force on the friction force was studied. In the second step, the friction force of the friction surface area is influenced. The effect of the change of the shear rate in step 3 on the friction force was investigated. At the last stage, the experimental study of the effect of the material selection on the friction force was made and it was seen that the aluminum / brass surface pair had the smallest friction coefficient as a result of the opening. The greatest coefficient of friction is found in the pair of glass / felt objects.

Does non-standard work mean non-standard health? Exploring links between non-standard work schedules, health behavior, and well-being

Directory of Open Access Journals (Sweden)

Megan R. Winkler

2018-04-01

Full Text Available The last century has seen dramatic shifts in population work circumstances, leading to an increasing normalization of non-standard work schedules (NSWSs, defined as non-daytime, irregular hours. An ever-growing body of evidence links NSWSs to a host of non-communicable chronic conditions; yet, these associations primarily concentrate on the physiologic mechanisms created by circadian disruption and insufficient sleep. While important, not all NSWSs create such chronobiologic disruption, and other aspects of working time and synchronization could be important to the relationships between work schedules and chronic disease. Leveraging survey data from Project EAT, a population-based study with health-related behavioral and psychological data from U.S. adults aged 25–36 years, this study explored the risks for a broad range of less healthful behavioral and well-being outcomes among NSWS workers compared to standard schedule workers (n = 1402. Variations across different NSWSs (evening, night/rotating, and irregular schedules were also explored. Results indicated that, relative to standard schedule workers, workers with NSWSs are at increased risk for non-optimal sleep, substance use, greater recreational screen time, worse dietary practices, obesity, and depression. There was minimal evidence to support differences in relative risks across workers with different types of NSWSs. The findings provide insight into the potential links between NSWSs and chronic disease and indicate the relevancy social disruption and daily health practices may play in the production of health and well-being outcomes among working populations. Keywords: United States, Work schedule tolerance, Health behavior, Mental health, Substance abuse, Obesity

Surface laser marking optimization using an experimental design approach

Science.gov (United States)

Brihmat-Hamadi, F.; Amara, E. H.; Lavisse, L.; Jouvard, J. M.; Cicala, E.; Kellou, H.

2017-04-01

Laser surface marking is performed on a titanium substrate using a pulsed frequency doubled Nd:YAG laser ( λ= 532 nm, τ pulse=5 ns) to process the substrate surface under normal atmospheric conditions. The aim of the work is to investigate, following experimental and statistical approaches, the correlation between the process parameters and the response variables (output), using a Design of Experiment method (DOE): Taguchi methodology and a response surface methodology (RSM). A design is first created using MINTAB program, and then the laser marking process is performed according to the planned design. The response variables; surface roughness and surface reflectance were measured for each sample, and incorporated into the design matrix. The results are then analyzed and the RSM model is developed and verified for predicting the process output for the given set of process parameters values. The analysis shows that the laser beam scanning speed is the most influential operating factor followed by the laser pumping intensity during marking, while the other factors show complex influences on the objective functions.

Numerical simulation and experimental analysis for a Risers Uphold Sub-Surface Buoy (BSR); Simulacao numerica e ensaio experimental da Boia de Sub-superficie de Suporte de Risers - BSSR

Energy Technology Data Exchange (ETDEWEB)

Araujo, Jairo B. de; Almeida, Jose Carlos L. de [PETROBRAS, Rio de Janeiro, RJ (Brazil); Rangel, Marcos; Fernandes, Antonio C.; Santos, Melquisedec F. dos; Sales Junior, Joel Sena [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia (COPPE)

2004-07-01

This paper presents results, numeric and experimental, due to installation operation of a Risers Uphold Sub-Surface Buoy, (BSR). This kind of installation developed by PETROBRAS is unique in the world. The work of BSR installation was based on a numeric pre analysis to verify the system and determine the main parameters to be experimentally verified. The second phase of the work was the experimental analysis in a deep water ocean basin. s. The work describes the BSR and their main accessories, the experimental environment and the model constructed in aluminum in a 1:12 scale and the main results. (author)

Surface physics theoretical models and experimental methods

CERN Document Server

Mamonova, Marina V; Prudnikova, I A

2016-01-01

The demands of production, such as thin films in microelectronics, rely on consideration of factors influencing the interaction of dissimilar materials that make contact with their surfaces. Bond formation between surface layers of dissimilar condensed solids-termed adhesion-depends on the nature of the contacting bodies. Thus, it is necessary to determine the characteristics of adhesion interaction of different materials from both applied and fundamental perspectives of surface phenomena. Given the difficulty in obtaining reliable experimental values of the adhesion strength of coatings, the theoretical approach to determining adhesion characteristics becomes more important. Surface Physics: Theoretical Models and Experimental Methods presents straightforward and efficient approaches and methods developed by the authors that enable the calculation of surface and adhesion characteristics for a wide range of materials: metals, alloys, semiconductors, and complex compounds. The authors compare results from the ...

Experimental work on drift chambers

International Nuclear Information System (INIS)

Alcaraz, J.; Duran, I.; Gonzalez, E.; Martinez-Laso, L.; Olmos, P.

1989-01-01

An experimental work made on drift chambers is described in two chapters. In the firt chapter we present the description of the experimental installation used, as well as some details on the data adquisition systems and the characteristics on three ways used for calibration proposes (cosmic muons, β radiation and test beam using SPS at CERN facilities). The second chapter describes the defferent prototypes studied. The experimental set up and the analysis are given. Some results are discussed. The magnetic field effect is also studied. (Author)

In vessel retention for VVER 1000 - Experimental work

International Nuclear Information System (INIS)

Batek, D.

2015-01-01

After Fukushima accident, the nuclear community realized that it is necessary to have strategy and solution for severe accident management. In Vessel Retention (IVR) of corium is an important strategy to mitigate the consequences of a severe accident. In this poster the author reviews the present status of experimental works made by UJV (Czech Republic) from 2012 until now, on the IVR strategy specifically applied for the VVER 1000 unit. The BESTH 1 experiment was prepared to test the behavior of the RPV (Reactor Pressure Vessel) surface under 2 configurations: clean and corroded. BESTH 2 experiment is a modification of BESTH 1 experiment in order to get greater thermal fluxes. The BESTH 3 facility is a large scale experiment that is under extensive design (2016-2017) whose main objective will be to investigate the results of vast analytical works made by experts with specialization of severe accident phenomenology

Experimental and theoretical study of surface tension of binary mixtures of (n-alkyl acetates + heptane, benzene, and toluene)

International Nuclear Information System (INIS)

Rafati, Amir Abbas; Ghasemian, Ensieh

2009-01-01

Surface properties of binary mixtures of (n-alkyl acetates + heptane, benzene, and toluene) have been measured by surface tension method at T = 298.15 K and atmospheric pressure. Also, the surface tension has been predicted based on the Suarez method. This method combines a model for the description of surface tension of liquid mixtures with a group contribution method for the calculation of activity coefficient. The mean relative standard deviations obtained from the comparison of experimental (measured) and calculated surface tension values for the eight binary systems are less than 1.5%, which leads to concluding that the model shows a good accuracy in different situations in comparison with other predicted equations. In addition, the relative Gibbs adsorption and the surface mole fraction have been evaluated using this model. The surface tension deviations were calculated from experimental results and have been fitted to the Redlich-Kister type polynomial relation

Static pressure and temperature coefficients of working standard microphones

DEFF Research Database (Denmark)

Barrera Figueroa, Salvador; Cutanda Henriquez, Vicente; Torras Rosell, Antoni

2016-01-01

be a significant contribution to the uncertainty of the measurement. Determining the environmental coefficients of individual specimens of measurement microphones can be a straightforward though time-consuming procedure provided the appropriate facilities are available. An alternative is to determine them using...... coefficients. For this purpose, the environmental coefficients of some commercially available microphones have been determined experimentally, and whenever possible, compared with the coefficients determined numerically using the Boundary Element Method....... for these coefficients which are used for calibration purposes. Working standard microphones are not exempt of these influences. However, manufacturers usually provide a low frequency value of the environmental coefficient. While in some applications the influence of this coefficient may be negligible, in others it may...

Digital economy and non-standard work

Directory of Open Access Journals (Sweden)

Patrizia Tullini

2016-12-01

Full Text Available Public and scientific debate on the digital economy is now widespread in many european countries. Also labour law scholars started to pay more attention to the new economical models and to the impact of digital technologies on productive processes. Economics and labour sciences should now move from a descriptive analysis to a deeper theoretical elaboration.The directions of the theoretical analysis are essentially two: the first one deals with the overbearing diffusion of non-standard forms of work on the web, especially on the digital platforms. This trend undermines the traditional foundation of subordination and affects the dynamics of global labour law market. The second directions deals with the increasing use of artificial intelligence in the industrial environment that presents new legal and social issues, concerning both the replacement of standard work with robotics and the complementarity between human work and «non-human agents» work.

Experimental pain leads to reorganisation of trapezius electromyography during computer work with active and passive pauses

DEFF Research Database (Denmark)

Samani, Afshin; Holtermann, Andreas; Søgaard, Karen

2009-01-01

The aim of this laboratory study was to investigate acute effects of experimental muscle pain on spatial electromyographic (EMG) activity of the trapezius muscle during computer work with active and passive pauses. Twelve healthy male subjects performed four sessions of computer work for 2 min...... in one day, with passive (relax) and active (30% maximum voluntary contraction of shoulder elevation) pauses given every 40 s without and with presence of experimental pain. Surface EMG signals were recorded from four parts of the trapezius. The centroid of exposure variation analysis along the time axis...... was lower during computer work with active pauses when compared with passive one in all muscle parts (P

CORROSION AND SURFACE PROTECTION IN MACHINE MATERIALS FRICTION HAVE DIFFERENT SURFACE PAIRS EXPERIMENTAL INVESTIGATION OF FACTORS

OpenAIRE

Senai YALCINKAYA

2017-01-01

Friction force, normal force, linear change. The normal force varies with the loads on the friction object. In order to determine the friction force and the friction coefficient, the friction object and the friction speed are used. The experimental work was carried out in three stages. In the first stage, the effect of normal force on the friction force was studied. In the second step, the friction force of the friction surface area is influenced. The effect of the change of the s...

Surface metal standards produced by ion implantation through a removable layer

International Nuclear Information System (INIS)

Schueler, B.W.; Granger, C.N.; McCaig, L.; McKinley, J.M.; Metz, J.; Mowat, I.; Reich, D.F.; Smith, S.; Stevie, F.A.; Yang, M.H.

2003-01-01

Surface metal concentration standards were produced by ion implantation and investigated for their suitability to calibrate surface metal measurements by secondary ion mass spectrometry (SIMS). Single isotope implants were made through a 100 nm oxide layer on silicon. The implant energies were chosen to place the peak of the implanted species at a depth of 100 nm. Subsequent removal of the oxide layer was used to expose the implant peak and to produce controlled surface metal concentrations. Surface metal concentration measurements by time-of-flight SIMS (TOF-SIMS) with an analysis depth of 1 nm agreed with the expected surface concentrations of the implant standards with a relative mean standard deviation of 20%. Since the TOF-SIMS relative sensitivity factors (RSFs) were originally derived from surface metal measurements of surface contaminated silicon wafers, the agreement implies that the implant standards can be used to measure RSF values. The homogeneity of the surface metal concentration was typically <10%. The dopant dose remaining in silicon after oxide removal was measured using the surface-SIMS protocol. The measured implant dose agreed with the expected dose with a mean relative standard deviation of 25%

Electron work function of metallic surfaces, covered with by metal adatoms, and two-dimensional structure of adlayer

International Nuclear Information System (INIS)

Rudnitskij, L.A.

1986-01-01

Change in electron work function during metal adatom (Ti, W, Ag, Au) adsorption on different tungsten surfaces in ''polycrystalline'' and epitaxial types of adsorpted layers is studied. Calculational and experimental dependences of work function change on coating thickness are built

Experimental tests on slip factor in friction joints: comparison between European and American Standards

Directory of Open Access Journals (Sweden)

Emanuele Maiorana

2018-01-01

Full Text Available Friction joints are used in steel structures submitted to cyclic loading such as, for example, in steel and composite bridges, in overhead cranes, and in equipment subjected to fatigue. Slip-critical steel joints with preloaded bolts are characterized by high rigidity and good performance against fatigue and vibrational phenomena. The most important parameter for the calculation of the bolt number in a friction connection is the slip factor, depending on the treatment of the plane surfaces inside the joint package. The paper focuses on the slip factor values reported in European and North American Specifications, and in literature references. The differences in experimental methods of slip test and evaluation of them for the mentioned standards are discussed. The results from laboratory tests regarding the assessment of the slip factor related to only sandblasted and sandblasted and coated surfaces are reported. Experimental data are compared with other results from the literature review to find the most influent parameters that control the slip factor in friction joint and differences between the slip tests procedures

40 CFR 60.103a - Work practice standards.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Work practice standards. 60.103a... Refineries for Which Construction, Reconstruction, or Modification Commenced After May 14, 2007 § 60.103a Work practice standards. (a) Each owner or operator that operates a flare that is subject to this...

Experimental investigation into effect of cutting parameters on surface integrity of hardened tool steel

Science.gov (United States)

Bashir, K.; Alkali, A. U.; Elmunafi, M. H. S.; Yusof, N. M.

2018-04-01

Recent trend in turning hardened materials have gained popularity because of its immense machinability benefits. However, several machining processes like thermal assisted machining and cryogenic machining have reveal superior machinability benefits over conventional dry turning of hardened materials. Various engineering materials have been studied. However, investigations on AISI O1 tool steel have not been widely reported. In this paper, surface finish and surface integrity dominant when hard turning AISI O1 tool steel is analysed. The study is focused on the performance of wiper coated ceramic tool with respect to surface roughness and surface integrity of hardened tool steel. Hard turned tool steel was machined at varying cutting speed of 100, 155 and 210 m/min and feed rate of 0.05, 0.125 and 0.20mm/rev. The depth of cut of 0.2mm was maintained constant throughout the machining trials. Machining was conducted using dry turning on 200E-axis CNC lathe. The experimental study revealed that the surface finish is relatively superior at higher cutting speed of 210m/min. The surface finish increases when cutting speed increases whereas surface finish is generally better at lower feed rate of 0.05mm/rev. The experimental study conducted have revealed that phenomena such as work piece vibration due to poor or improper mounting on the spindle also contributed to higher surface roughness value of 0.66Ra during turning at 0.2mm/rev. Traces of white layer was observed when viewed with optical microscope which shows evidence of cutting effects on the turned work material at feed rate of 0.2 rev/min

Necessary and Sufficient Process leading to Work Smart Standards. Final report

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-11-01

The Necessary and Sufficient Process leading to Work Smart Standards is a Department of Energy initiative to assure adequate protection for workers, the public, and the environment. The Work Smart Standards initiative directs the Laboratory to develop a set of ES and H standards based on the work performed at the Laboratory and the hazards associated with the work. Berkeley Lab`s set of Work Smart Standards includes required Federal, State and local laws and, additionally, national and international standards which represent the highest operating standards of industrial and commercial institutions.

Necessary and Sufficient Process leading to Work Smart Standards. Final report

International Nuclear Information System (INIS)

1996-11-01

The Necessary and Sufficient Process leading to Work Smart Standards is a Department of Energy initiative to assure adequate protection for workers, the public, and the environment. The Work Smart Standards initiative directs the Laboratory to develop a set of ES and H standards based on the work performed at the Laboratory and the hazards associated with the work. Berkeley Lab's set of Work Smart Standards includes required Federal, State and local laws and, additionally, national and international standards which represent the highest operating standards of industrial and commercial institutions

Functional work breaks in a high-demanding work environment: an experimental field study.

Science.gov (United States)

Scholz, André; Ghadiri, Argang; Singh, Usha; Wendsche, Johannes; Peters, Theo; Schneider, Stefan

2018-02-01

Work breaks are known to have positive effects on employees' health, performance and safety. Using a sample of twelve employees working in a stressful and cognitively demanding working environment, this experimental field study examined how different types of work breaks (boxing, deep relaxation and usual breaks) affect participants' mood, cognitive performance and neurophysiological state compared to a control condition without any break. In a repeated measures experimental design, cognitive performance was assessed using an auditory oddball test and a Movement Detection Test. Brain cortical activity was recorded using electroencephalography. Individual's mood was analysed using a profile of mood state. Although neurophysiological data showed improved relaxation of cortical state after boxing (vs. 'no break' and 'deep relaxation'), neither performance nor mood assessment showed similar results. It remains questionable whether there is a universal work break type that has beneficial effects for all individuals. Practitioner Summary: Research on work breaks and their positive effects on employees' health and performance often disregards break activities. This experimental field study in a stressful working environment investigated the effect of different work break activities. A universal work break type that is beneficial for this workplace could not be identified.

Calibration of working standard ionization chambers and dose standardization

International Nuclear Information System (INIS)

Abd Elmahoud, A. A. B.

2011-01-01

Measurements were performed for the calibration of two working standard ionization chambers in the secondary standard dosimetry laboratory of Sudan. 600 cc cylindrical former type and 1800 cc cylindrical radical radiation protection level ionization chambers were calibrated against 1000 cc spherical reference standard ionization chamber. The chamber were calibrated at X-ray narrow spectrum series with beam energies ranged from (33-116 KeV) in addition to 1''3''7''Cs beam with 662 KeV energy. The chambers 0.6 cc and 0.3 cc therapy level ionization were used for dose standardization and beam output calibrations of cobalt-60 radiotherapy machine located at the National Cancer Institute, University of Gazira. Concerning beam output measurements for 6''0''Co radiotherapy machine, dosimetric measurements were performed in accordance with the relevant per IAEA dosimetry protocols TRS-277 and TRS-398. The kinetic energy released per unit mass in air (air kerma) were obtained by multiplying the corrected electrometer reading (nC/min) by the calibration factors (Gy/n C) of the chambers from given in the calibration certificate. The uncertainty of measurements of air kerma were calculated for the all ionization chambers (combined uncertainty) the calibration factors of these ionization chambers then were calculated by comparing the reading of air kerma of secondary standard ionization chambers to than from radical and farmer chambers. The result of calibration working standard ionization chambers showed different calibration factors ranged from 0.99 to 1.52 for different radiation energies and these differences were due to chambers response and specification. The absorbed dose to to water calculated for therapy ionization chamber using two code of practice TRS-277 and TRS-398 as beam output for 6''0''Co radiotherapy machine and it can be used as a reference for future beam output calibration in radiotherapy dosimetry. The measurement of absorbed dose to water showed that the

Experimental and numerical investigation of laser forming of cylindrical surfaces with arbitrary radius of curvature

Directory of Open Access Journals (Sweden)

Mehdi Safari

2016-09-01

Full Text Available In this work, laser forming of cylindrical surfaces with arbitrary radius of curvature is investigated experimentally and numerically. For laser forming of cylindrical surfaces with arbitrary radius of curvature, a new and comprehensive method is proposed in this paper. This method contains simple linear irradiating lines and using an analytical method, required process parameters for laser forming of a cylindrical surface with a specific radius of curvature is proposed. In this method, laser output power, laser scanning speed and laser beam diameter are selected based on laser machine and process limitations. As in the laser forming of a cylindrical surface, parallel irradiating lines are needed; therefore key parameter for production of a cylindrical surface with a specific radius of curvature is the number of irradiating lines. Hence, in the proposed analytical method, the required number of irradiating lines for production of a cylindrical surface with a specific radius of curvature is suggested. Performance of the proposed method for production of cylindrical surface with a specific radius of curvature is verified with experimental tests. The results show that using proposed analytical method, cylindrical surfaces with any radius of curvature can be produced successfully.

The new fabrication method of standard surface sources

Energy Technology Data Exchange (ETDEWEB)

Sato, Yasushi E-mail: yss.sato@aist.go.jp; Hino, Yoshio; Yamada, Takahiro; Matsumoto, Mikio

2004-04-01

We developed a new fabrication method for standard surface sources by using an inkjet printer with inks in which a radioactive material is mixed to print on a sheet of paper. Three printed test patterns have been prepared: (1) 100 mmx100 mm uniformity-test patterns, (2) positional-resolution test patterns with different widths and intervals of straight lines, and (3) logarithmic intensity test patterns with different radioactive intensities. The results revealed that the fabricated standard surface sources had high uniformity, high positional resolution, arbitrary shapes and a broad intensity range.

Report of working group for technical standard of cutting and melting works in Glovebox dismantling

International Nuclear Information System (INIS)

Asazuma, Shinichiroh; Takeda, Shinsoh; Tajima, Shoichi

2004-11-01

In order to prevent spread of contamination, glovebox dismantling activity is usually performed in a confined enclosure with personal radioactive protective equipment. Since large potion of these materials is made of vinyl acetate, there exist potential risks of fire, damage and injury to the environment and workers during the dismantling (cutting or melting) operation. It is therefore important to establish standard for proper use of equipment and hazard controls in such a specific environment. Working Group composed of Tokai Works and Oarai Works has examined and developed the operational standard for cutting work in glovebox dismantlement. The result is reflected to the Tokai Works Safety Operational Standard. (author)

Preparation and characterisation of glass surfaces for experimental purposes

International Nuclear Information System (INIS)

Serruys, Y.

1986-01-01

Experimental investigation of glasses, applied especially to the prevision of the behaviour of vitrified nuclear wastes, requires the preparation of well-defined and reproducibles surfaces, in order to separate the investigated phenomena from artifacts due to surface anomalies and to allow a valuable comparison between results obtained in different laboratories. The aim of the present report is to determine which characters, both physical and chemical, of glass surfaces, have to be controlled, because of their influence upon the investigated phenomena or the experimental processes employed in the investigation. A method is then presented for a surface preparation giving good guaranties of quality and reproducibility. The physical and chemical aspects of surface characterisation are successively considered. The relevant characters and their importance are described, then the corresponding techniques of characterisation are reviewed and it has been attempted to propose a set of techniques allowing a characterisation as complete as possible for laboratory purposes. A preparation method for experimental sample, aiming to satisfy all the previously defined criteria, is then proposed, and present results obtained with this method are described [fr

Surface acidity scales: Experimental measurements of Brønsted acidities on anatase TiO2 and comparison with coinage metal surfaces

Science.gov (United States)

Silbaugh, Trent L.; Boaventura, Jaime S.; Barteau, Mark A.

2016-08-01

The first quantitative surface acidity scale for Brønsted acids on a solid surface is presented through the use of titration-displacement and equilibrium experiments on anatase TiO2. Surface acidities of species on TiO2 correlated with gas phase acidities, as was previously observed in qualitative studies of Brønsted acid displacement on Ag(110), Cu(110) and Au(111). A 90% compression of the surface acidity scale relative to the gas phase was observed due to compensation from the covalent component of the conjugate base - surface bond. Adsorbed conjugate bases need not be completely anionic for correlations with gas phase acidities to hold. Positive and negative substituent effects, such as substituted fluorine and hydrocarbon sidechain dispersion interactions with the surface, may modify the surface acidity scale, in agreement with previous experimental and theoretical work on Au(111).

Standardized Flexibility: The Choreography of ICT in Standardization of Service Work

Directory of Open Access Journals (Sweden)

Maria Røhnebæk

2012-12-01

Full Text Available This article is based on a research project that explores the proliferation of infor-mation and communication technology (ICT in public services. Furthermore, the research explores how the enhanced presence of ICT relates to efforts to increas-ingly individualise the service delivery. It can be argued that enhanced individual-isation requires increased levels of discretion and flexibility. At the same time, this flexibility needs to be implemented within a standardized framework to ensure due process and to meet demands for efficiency. As local-level work practices in the public services are increasingly being enabled through ICT, the information systems can thus be seen to offer ‘standardized flexibility’. Hence, the information systems work as both enablers of flexibility and as controllers of the same. This research explores how this duality manifests empirically at the local-level of the Norwegian employment and welfare services (NAV. It focuses on the in-terface of the information systems and local-level employees. In this article, I por-tray the role of the information system, Arena, with regard to how the front-line employees structure and organize their work. This portrayal reveals that the in-formation system reflects an ideal world which is out of tune with local working conditions. The employees are thus facing gaps between the ideals of the system and their actual work context. The main purpose of the paper is to illustrate how the employees deal with this gap; I identify three types of responses and strate-gies. Moreover, I suggest that the relationship between the information systems and different kinds of local responses may be fruitfully analysed by drawing an analogy with choreography and dancing. The second purpose of this article is thus to outline how the metaphor of choreography may provide a suitable theoretical lens for analysing ICT-enabled standardization of work.

Experimental and numerical analyses of different extended surfaces

International Nuclear Information System (INIS)

Diani, A; Mancin, S; Zilio, C; Rossetto, L

2012-01-01

Air is a cheap and safe fluid, widely used in electronic, aerospace and air conditioning applications. Because of its poor heat transfer properties, it always flows through extended surfaces, such as finned surfaces, to enhance the convective heat transfer. In this paper, experimental results are reviewed and numerical studies during air forced convection through extended surfaces are presented. The thermal and hydraulic behaviours of a reference trapezoidal finned surface, experimentally evaluated by present authors in an open-circuit wind tunnel, has been compared with numerical simulations carried out by using the commercial CFD software COMSOL Multiphysics. Once the model has been validated, numerical simulations have been extended to other rectangular finned configurations, in order to study the effects of the fin thickness, fin pitch and fin height on the thermo-hydraulic behaviour of the extended surfaces. Moreover, several pin fin surfaces have been simulated in the same range of operating conditions previously analyzed. Numerical results about heat transfer and pressure drop, for both plain finned and pin fin surfaces, have been compared with empirical correlations from the open literature, and more accurate equations have been developed, proposed, and validated.

Experimental determination of the thermal contact conductance between two solid surfaces by the energy pulse technique

International Nuclear Information System (INIS)

Rubin, Gerson Antonio

1979-01-01

An experimental procedure for the determination of the thermal contact conductance between two solid surfaces as a function of the contact pressure and the energy of the laser radiation has been developed using the laser pulse method. A rubi laser with variable energy levels was employed as a radiating pulse energy source. The laser beam was allowed to impinge perpendicularly on the front face of a electrolytic iron 73 4 . The temperature fluctuations resulting on the back surface of the sample was detected by a thermocouple, which Is coupled to a PDP-11/45 Computer 32 Kbytes of memory, through a Analog-Digital Converter. A theoretical function, derived exclusively for the problem mentioned in this work, was adjusted by a method of least square fitting of experimental results. This adjustment yielded the value of a parameter related to the contact conductance between two surfaces. The experimental error obtained for the thermal contact conductance was +- 4.9%. (author)

Surface computing and collaborative analysis work

CERN Document Server

Brown, Judith; Gossage, Stevenson; Hack, Chris

2013-01-01

Large surface computing devices (wall-mounted or tabletop) with touch interfaces and their application to collaborative data analysis, an increasingly important and prevalent activity, is the primary topic of this book. Our goals are to outline the fundamentals of surface computing (a still maturing technology), review relevant work on collaborative data analysis, describe frameworks for understanding collaborative processes, and provide a better understanding of the opportunities for research and development. We describe surfaces as display technologies with which people can interact directly, and emphasize how interaction design changes when designing for large surfaces. We review efforts to use large displays, surfaces or mixed display environments to enable collaborative analytic activity. Collaborative analysis is important in many domains, but to provide concrete examples and a specific focus, we frequently consider analysis work in the security domain, and in particular the challenges security personne...

Interdisciplinary Development of an Improved Emergency Department Procedural Work Surface Through Iterative Design and Use Testing in Simulated and Clinical Environments.

Science.gov (United States)

Zhang, Xiao C; Bermudez, Ana M; Reddy, Pranav M; Sarpatwari, Ravi R; Chheng, Darin B; Mezoian, Taylor J; Schwartz, Victoria R; Simmons, Quinneil J; Jay, Gregory D; Kobayashi, Leo

2017-03-01

A stable and readily accessible work surface for bedside medical procedures represents a valuable tool for acute care providers. In emergency department (ED) settings, the design and implementation of traditional Mayo stands and related surface devices often limit their availability, portability, and usability, which can lead to suboptimal clinical practice conditions that may affect the safe and effective performance of medical procedures and delivery of patient care. We designed and built a novel, open-source, portable, bedside procedural surface through an iterative development process with use testing in simulated and live clinical environments. The procedural surface development project was conducted between October 2014 and June 2016 at an academic referral hospital and its affiliated simulation facility. An interdisciplinary team of emergency physicians, mechanical engineers, medical students, and design students sought to construct a prototype bedside procedural surface out of off-the-shelf hardware during a collaborative university course on health care design. After determination of end-user needs and core design requirements, multiple prototypes were fabricated and iteratively modified, with early variants featuring undermattress stabilizing supports or ratcheting clamp mechanisms. Versions 1 through 4 underwent 2 hands-on usability-testing simulation sessions; version 5 was presented at a design critique held jointly by a panel of clinical and industrial design faculty for expert feedback. Responding to select feedback elements over several surface versions, investigators arrived at a near-final prototype design for fabrication and use testing in a live clinical setting. This experimental procedural surface (version 8) was constructed and then deployed for controlled usability testing against the standard Mayo stands in use at the study site ED. Clinical providers working in the ED who opted to participate in the study were provided with the prototype

Effectiveness of Student Learning during Experimental Work in Primary School.

Science.gov (United States)

Logar, Ana; Peklaj, Cirila; Ferk Savec, Vesna

2017-09-01

The aim of the research was to optimize the effectiveness of student learning based on experimental work in chemistry classes in Slovenian primary schools. To obtain evidence about how experimental work is implemented during regular chemistry classes, experimental work was videotaped during 19 units of chemistry lessons at 12 Slovenian primary schools from the pool of randomly selected schools. Altogether 332 eight-grade students were involved in the investigation, with an average age of 14.2 years. Students were videotaped during chemistry lessons, and their worksheets were collected afterward. The 12 chemistry teachers, who conducted lessons in these schools, were interviewed before the lessons; their teaching plans were also collected. The collected data was analyzed using qualitative methods. The results indicate that many teachers in Slovenian primary schools are not fully aware of the potential of experimental work integrated into chemistry lessons for the development of students' experimental competence. Further research of the value of different kinds of training to support teachers for the use of experimental work in chemistry teaching is needed.

Experimental and numerical investigation of liquid-metal free-surface flows in spallation targets

Energy Technology Data Exchange (ETDEWEB)

Batta, A., E-mail: batta@kit.edu [Karlsruhe Institute of Technology, Germany Hermann-von-Helmholtz-PLATZ 1, 76344 Eggenstein-Leopoldshafen (Germany); Class, A.G.; Litfin, K.; Wetzel, Th. [Karlsruhe Institute of Technology, Germany Hermann-von-Helmholtz-PLATZ 1, 76344 Eggenstein-Leopoldshafen (Germany); Moreau, V.; Massidda, L. [CRS4 Centre for Advanced Studies, Research and Development in Sardinia, Polaris, Edificio 1, 09010 Pula, CA (Italy); Thomas, S.; Lakehal, D. [ASCOMP GmbH Zurich, Zurich (Switzerland); Angeli, D.; Losi, G. [DIEF – Department of Engineering “Enzo Ferrari”, University of Modena and Reggio Emilia, via Vignolese 905, 41125 Modena (Italy); Mooney, K.G. [University of Massachusetts Amherst, Department of Mechanical and Industrial Engineering, Amherst (United States); Van Tichelen, K. [SCK-CEN, Belgian Nuclear Research Centre, Boeretang 200, 2400 Mol (Belgium)

2015-08-15

Highlights: • Experimental study of free surface for lead bismuth eutectic target. • Numerical investigation of free surface of a liquid metal target. • Advanced free surface modelling. - Abstract: Accelerator Driven Systems (ADS) are extensively investigated for the transmutation of high-level nuclear waste within many worldwide research programs. The first advanced design of an ADS system is currently developed in SCK• CEN, Mol, Belgium: the Multi-purpose hYbrid Research Reactor for High-tech Applications (MYRRHA). Many European research programs support the design of MYRRHA. In the framework of the Euratom project ‘Thermal Hydraulics of Innovative nuclear Systems (THINS)’ a liquid-metal free-surface experiment is performed at the Karlsruhe Liquid Metal Laboratory (KALLA) of Karlsruhe Institute of Technology (KIT). The experiment investigates a full-scale model of the concentric free-surface spallation target of MYRRHA using Lead Bismuth Eutectic (LBE) as coolant. In parallel, numerical free surface models are developed and tested which are reviewed in the article. A volume-of-fluid method, a moving mesh model, a free surface model combining the Level-Set method with Large-Eddy Simulation model and a smoothed-particle hydrodynamics approach are investigated. Verification of the tested models is based on the experimental results obtained within the THINS project and on previous water experiments performed at the University Catholic de Louvain (UCL) within the Euratom project ‘EUROpean Research Programme for the TRANSmutation of High Level Nuclear Waste in Accelerator Driven System (EUROTRANS)’. The design of the target enables a high fluid velocity and a stable surface at the beam entry. The purpose of this paper is to present an overview of both experimental and numerical results obtained for free surface target characterization. Without entering in technical details, the status, the major achievements and lessons for the future with respect to

Assessment of work-related muscle strain by using surface EMG during test contractions interposed between work periods of simulateted mushroom picking

DEFF Research Database (Denmark)

Ohashi, Jun-Ya; Blangsted, Anne Katrine; Nielsen, Pernille Kofoed

2010-01-01

Surface electromyograms(EMG) during test contractions (TCs) were studied to assess the muscle strain in simulated mushroom picking. Additionally, the duration of the TC for the effective assessment was investigated. Nine female subjects performed standardized shoulder abduction and a stooped...... posture for one minute as TCs. Each experiment consisted of a 60-min rest, three work periods (W1-W3), a 30-min rest, and two work periods (W4 and W5) separated by a 30-min rest period. The duration of each work period was about 20 min. A total of 18 TCs was performed between the work periods and every 10...

Experimental Method for Measuring Dust Load on Surfaces in Rooms

DEFF Research Database (Denmark)

Lengweiler, Philip; Nielsen, Peter V.; Moser, Alfred

A new experimental setup to investigate the physical process of dust deposition and resuspension on and from surfaces is introduced. Dust deposition can reduce the airborne dust concentration considerably. As a basis for developing methods to eliminate dust-related problems in rooms, there is a n......A new experimental setup to investigate the physical process of dust deposition and resuspension on and from surfaces is introduced. Dust deposition can reduce the airborne dust concentration considerably. As a basis for developing methods to eliminate dust-related problems in rooms......, there is a need for better understanding of the mechanism of dust deposition and resuspension. With the presented experimental setup, the dust load on surfaces in a channel can be measured as a function of the environmental and surface conditions and the type of particles under controlled laboratory conditions....

Relationship between non-standard work arrangements and work-related accident absence in Belgium.

Science.gov (United States)

Alali, Hanan; Braeckman, Lutgart; Van Hecke, Tanja; De Clercq, Bart; Janssens, Heidi; Wahab, Magd Abdel

2017-03-28

The main objective of this study is to examine the relationship between indicators of non-standard work arrangements, including precarious contract, long working hours, multiple jobs, shift work, and work-related accident absence, using a representative Belgian sample and considering several socio-demographic and work characteristics. This study was based on the data of the fifth European Working Conditions Survey (EWCS). For the analysis, the sample was restricted to 3343 respondents from Belgium who were all employed workers. The associations between non-standard work arrangements and work-related accident absence were studied with multivariate logistic regression modeling techniques while adjusting for several confounders. During the last 12 months, about 11.7% of workers were absent from work because of work-related accident. A multivariate regression model showed an increased injury risk for those performing shift work (OR 1.546, 95% CI 1.074-2.224). The relationship between contract type and occupational injuries was not significant (OR 1.163, 95% CI 0.739-1.831). Furthermore, no statistically significant differences were observed for those performing long working hours (OR 1.217, 95% CI 0.638-2.321) and those performing multiple jobs (OR 1.361, 95% CI 0.827-2.240) in relation to work-related accident absence. Those who rated their health as bad, low educated workers, workers from the construction sector, and those exposed to biomechanical exposure (BM) were more frequent victims of work-related accident absence. No significant gender difference was observed. Indicators of non-standard work arrangements under this study, except shift work, were not significantly associated with work-related accident absence. To reduce the burden of occupational injuries, not only risk reduction strategies and interventions are needed but also policy efforts are to be undertaken to limit shift work. In general, preventive measures and more training on the job are needed to

The Work of Globalization: How Standardization May Impact the Globalization of Work

OpenAIRE

Cochoy , Franck

2002-01-01

Does the globalization of product markets entail a globalization of labor? In order to answer this type of question, the paper tries to highlight the link between the impossible globalization of work and the continuous emergence of standardization as a “work of globalization”.

Blade Surface Pressure Distributions in a Rocket Engine Turbine: Experimental Work With On-Blade Pressure Transducers

Science.gov (United States)

Hudson, Susan T.; Zoladz, Thomas F.; Griffin, Lisa W.; Turner, James E. (Technical Monitor)

2000-01-01

Understanding the unsteady aspects of turbine rotor flowfields is critical to successful future turbine designs. A technology program was conducted at NASA's Marshall Space Flight Center to increase the understanding of unsteady environments for rocket engine turbines. The experimental program involved instrumenting turbine rotor blades with surface-mounted high frequency response pressure transducers. The turbine model was then tested to measure the unsteady pressures on the rotor blades. The data obtained from the experimental program is unique in three respects. First, much more unsteady data was obtained (several minutes per set point) than has been possible in the past. Also, two independent unsteady data acquisition systems and fundamental signal processing approaches were used. Finally, an extensive steady performance database existed for the turbine model. This allowed an evaluation of the effect of the on-blade instrumentation on the turbine's performance. This unique data set, the lessons learned for acquiring this type of data, and the improvements made to the data analysis and prediction tools will contribute to future turbine programs such as those for reusable launch vehicles.

Assessment of slipping resistance of footwear and floor surfaces. Influence of manufacture and utilization of the products.

Science.gov (United States)

Leclercq, S; Tisserand, M; Saulnier, H

1995-02-01

The slipping resistance of footwear or floor surfaces is a characteristic which it is vital to be able to quantify. Work is being carried out at the International Standard Organization (ISO) and at the European Committee for Standardization (CEN) into the slip resistance of both work shoes and protective footwear, involving analysis of the latest developments in both the validity of measuring methods and the extent of the influence of certain experimental parameters on the slip resistance. Two industrial factors, independent of the measuring process but essential to the determination of the coefficient of friction of the models have been experimentally studied, namely the effect of the manufacture of the footwear or floor surfaces on the scattering of the specific coefficient of friction of a referenced model and the effect on the coefficient of friction of mechanical wear and tear on the soles as a result of their use respectively. Work into slipping on industrial floor surfaces is less advanced. Yet, problems raised call for the same approach than for problems linked to slipping resistance of footwear, and applications will be also at first related to standardized measurement conditions.

Effectiveness of student learning during experimental work in primary school

OpenAIRE

Logar, Ana; Peklaj, Cirila; Ferk Savec, Vesna

2017-01-01

The aim of the research was to optimize the effectiveness of student learning based on experimental work in chemistry classes in Slovenian primary schools. To obtain evidence about how experimental work is implemented during regular chemistry classes, experimental work was videotaped during 19 units of chemistry lessons at 12 Slovenian primary schools from the pool of randomly selected schools. Altogether 332 eight-grade students were involved in the investigation, with an average...

Development of an experimentally supported evaluation method for optimization and characterization of strain transfer of surface-applied Fibre Bragg Gratings (FBG); Entwicklung eines experimentell gestuetzten Bewertungsverfahrens zur Optimierung und Charakterisierung der Dehnungsuebertragung oberflaechenapplizierter Faser-Bragg-Gitter-Sensoren

Energy Technology Data Exchange (ETDEWEB)

Schlueter, Vivien Gisela

2010-05-01

Fibre Bragg Gratings (FBG) as strain sensors are implemented in those areas, where conventional electrical strain gauges reach their limits (for example in areas of high voltage, strong electro-magnetic fields, medical technology, safety relevant and radiation-exposed areas). Subject of this work is the surface application and the qualification of these sensors as strain sensors on different materials. A certified and proven method of application for surface mounted sensors is not known yet. The determination of the strain transfer and the definition of a strain transfer factor out of the relation between the Bragg wavelength change and the strain of the specimen have not yet been validated experimentally with an independent validation method. The development of an experimental methodology using a physically independent optical reference method for the determination of the strain transfer between the specimen and the FBG strain sensor is the main focus of this work. The influencing parameters on the strain distribution have been quantified experimentally and the change in Bragg wavelength has been investigated in relation to the strain measured by strain gauges. The material properties of the adhesives have been partly investigated. On the basis of these experiments a testing facility for surface applied FBG strain sensors has been developed. The functionality of the experimental methodology for the determination of the strain factor has been shown. The characterisation of the testing facility and the validity of FBG strain sensors through the experimental methodology inhere developed have been started. For the case of the strain determination in wind turbine rotor blades specially adapted FBG patches have been developed and qualified. An integration technique for FBG strain sensors into the rotor blade has been developed as well. As a first step of standardizing this measurement technique a national standard has been developed under the contribution of the author

Experimental and numerical studies on free surface flow of windowless target

International Nuclear Information System (INIS)

Su, G.Y.; Gu, H.Y.; Cheng, X.

2012-01-01

Highlights: ► Experimental and CFD studies on free surface flow have been performed in a scaled windowless target. ► Flow structure inside spallation area can be divided into three typical zones. ► Under large Reynolds number, large scale vortex can be observed. ► CFD studies have been conducted by using both LES and RANS (k-ω SST) turbulence models. ► LES model provides better numerical prediction on free surface behavior and flow transient. - Abstract: The formation and control method of the coolant free surface is one of the key technologies for the design of windowless targets in the accelerator driven system (ADS). In the recent study, experimental and numerical investigations on the free surface flow have been performed in a scaled windowless target by using water as the model fluid. The planar laser induced fluorescence technique has been applied to visualize the free surface flow pattern inside the spallation area. Experiments have been carried out with the Reynolds number in the range of 30,000–50,000. The structure and features of flow vortex have been investigated. The experimental results show that the free surface is vulnerable to the vortex movement. In addition, CFD simulations have been performed under the experimental conditions, using LES and RANS (k-ω SST) turbulence models, respectively. The numerical results of LES model agree qualitatively well with the experimental data related to both flow pattern and free surface behavior.

2D transient granular flows over obstacles: experimental and numerical work

Science.gov (United States)

Juez, Carmelo; Caviedes-Voullième, Daniel; Murillo, Javier; García-Navarro, Pilar

2016-04-01

Landslides are an ubiquitous natural hazard, and therefore human infrastructure and settlements are often at risk in mountainous regions. In order to better understand and predict landslides, systematic studies of the phenomena need to be undertaken. In particular, computational tools which allow for analysis of field problems require to be thoroughly tested, calibrated and validated under controlled conditions. And to do so, it is necessary for such controlled experiments to be fully characterized in the same terms as the numerical model requires. This work presents an experimental study of dry granular flow over a rough bed with topography which resembles a mountain valley. It has an upper region with a very high slope. The geometry of the bed describes a fourth order polynomial curve, with a low point with zero slope, and afterwards a short region with adverse slope. Obstacles are present in the lower regions which are used as model geometries of human structures. The experiments consisted of a sudden release a mass of sand on the upper region, and allowing it to flow downslope. Furthermore, it has been frequent in previous studies to measure final states of the granular mass at rest, but seldom has transient data being provided, and never for the entire field. In this work we present transient measurements of the moving granular surfaces, obtained with a consumer-grade RGB-D sensor. The sensor, developed for the videogame industry, allows to measure the moving surface of the sand, thus obtaining elevation fields. The experimental results are very consistent and repeatable. The measured surfaces clearly show the distinctive features of the granular flow around the obstacles and allow to qualitatively describe the different flow patterns. More importantly, the quantitative description of the granular surface allows for benchmarking and calibration of predictive numerical models, key in scaling the small-scale experimental knowledge into the field. In addition, as

Surface dimpling on rotating work piece using rotation cutting tool

Science.gov (United States)

Bhapkar, Rohit Arun; Larsen, Eric Richard

2015-03-31

A combined method of machining and applying a surface texture to a work piece and a tool assembly that is capable of machining and applying a surface texture to a work piece are disclosed. The disclosed method includes machining portions of an outer or inner surface of a work piece. The method also includes rotating the work piece in front of a rotating cutting tool and engaging the outer surface of the work piece with the rotating cutting tool to cut dimples in the outer surface of the work piece. The disclosed tool assembly includes a rotating cutting tool coupled to an end of a rotational machining device, such as a lathe. The same tool assembly can be used to both machine the work piece and apply a surface texture to the work piece without unloading the work piece from the tool assembly.

Creating NDA working standards through high-fidelity spent fuel modeling

International Nuclear Information System (INIS)

Skutnik, Steven E.; Gauld, Ian C.; Romano, Catherine E.; Trellue, Holly

2012-01-01

The Next Generation Safeguards Initiative (NGSI) is developing advanced non-destructive assay (NDA) techniques for spent nuclear fuel assemblies to advance the state-of-the-art in safeguards measurements. These measurements aim beyond the capabilities of existing methods to include the evaluation of plutonium and fissile material inventory, independent of operator declarations. Testing and evaluation of advanced NDA performance will require reference assemblies with well-characterized compositions to serve as working standards against which the NDA methods can be benchmarked and for uncertainty quantification. To support the development of standards for the NGSI spent fuel NDA project, high-fidelity modeling of irradiated fuel assemblies is being performed to characterize fuel compositions and radiation emission data. The assembly depletion simulations apply detailed operating history information and core simulation data as it is available to perform high fidelity axial and pin-by-pin fuel characterization for more than 1600 nuclides. The resulting pin-by-pin isotopic inventories are used to optimize the NDA measurements and provide information necessary to unfold and interpret the measurement data, e.g., passive gamma emitters, neutron emitters, neutron absorbers, and fissile content. A key requirement of this study is the analysis of uncertainties associated with the calculated compositions and signatures for the standard assemblies; uncertainties introduced by the calculation methods, nuclear data, and operating information. An integral part of this assessment involves the application of experimental data from destructive radiochemical assay to assess the uncertainty and bias in computed inventories, the impact of parameters such as assembly burnup gradients and burnable poisons, and the influence of neighboring assemblies on periphery rods. This paper will present the results of high fidelity assembly depletion modeling and uncertainty analysis from independent

Experimental determinations of the performances of heat transfer surfaces

International Nuclear Information System (INIS)

Pirovano, Alain; Viannay, Stephane; Mazeas, C.Y.

1974-01-01

With the help of flow schemes and of assumptions on the heat transfer, it is possible, in some cases, to predict the thermal and aerodynamical performances of a new heat transfer surface with moderate accuracy. These estimates, valid for an approximate classification of a new surface among known surfaces, are not accurate enough to be taken as a basis for the design of heat exchangers. In the present state of knowledge, the performances of a new heat transfer surface can only be determined accurately with experimental measurements. Bertin and Co have at their disposal two air test rigs especially designed for this purpose. The first one, more directly concerned with the measurements on tube bundles with fluid flow perpendicular to the generatrices of the tubes, is a semi-closed loop equipped with a high-efficiency ejector which amplifies the air flow rate supplied by an external source and thus allows high values of Reynolds number to be reached. The second one is adapted to other types of surfaces: tubes with external flow parallel to the generatrices, tubes with sophisticated cross section and with internal flow, compact surfaces with finned plates, etc. Both test rigs, the relevant equipment, the methods of data acquisition and of test results analysis are described in this paper. During the 5 past years, 60 configurations were tested. It was possible to compare some of the test results with the results of measurements performed later, on entire heat exchangers working with numbers of tubes, fluids, and temperature levels different from those prevailing during the tests on the small scale mock-up; the agreement is quite good [fr

Experimental study on source efficiencies for estimating surface contamination level

International Nuclear Information System (INIS)

Ichiji, Takeshi; Ogino, Haruyuki

2008-01-01

Source efficiency was measured experimentally for various materials, such as metals, nonmetals, flooring materials, sheet materials and other materials, contaminated by alpha and beta emitter radioactive nuclides. Five nuclides, 147 Pm, 60 Co, 137 Cs, 204 Tl and 90 Sr- 90 Y, were used as the beta emitters, and one nuclide 241 Am was used as the alpha emitter. The test samples were prepared by placing drops of the radioactive standardized solutions uniformly on the various materials using an automatic quantitative dispenser system from Musashi Engineering, Inc. After placing drops of the radioactive standardized solutions, the test materials were allowed to dry for more than 12 hours in a draft chamber with a hood. The radioactivity of each test material was about 30 Bq. Beta rays or alpha rays from the test materials were measured with a 2-pi gas flow proportional counter from Aloka Co., Ltd. The source efficiencies of the metals, nonmetals and sheet materials were higher than 0.5 in the case of contamination by the 137 Cs, 204 Tl and 90 Sr- 90 Y radioactive standardized solutions, higher than 0.4 in the case of contamination by the 60 Co radioactive standardized solution, and higher than 0.25 in the case of contamination by the alpha emitter the 241 Am radioactive standardized solution. These values were higher than those given in Japanese Industrial Standards (JIS) documents. In contrast, the source efficiencies of some permeable materials were lower than those given in JIS documents, because source efficiency varies depending on whether the materials or radioactive sources are wet or dry. This study provides basic data on source efficiency, which is useful for estimating the surface contamination level of materials. (author)

Standard compensation for power cuts. Working group report

International Nuclear Information System (INIS)

2002-07-01

The Working Group was commissioned to draw up a proposal in the form of a Government Bill for provisions to be included in the Electricity Market Act on imposing an obligation on the distribution net operator to pay a standard compensation to the users of electricity for the event that they get no access to electricity. The Working Group should consider especially a model of standard compensation presented in the final report by Mr. Jarl Forsten, Deputy Director General of the Technical Research Centre of Finland VTT, published on 30 April 2002 that the amount of standard compensation should not depend on the reason for the power cut. The Working Group proposes that the Electricity Market Act should be amended by provisions providing that a distribution net operator shall pay to the user of electricity a standard compensation for power cuts lasting over 12 hours. The amount of compensation shall be based on the annual network service fee and a sliding scale of compensation related to the duration of the power cut shall be applied. The maximum compensation shall be paid when the power cut lasts more than five days. The maximum amount of individual compensations shall be fixed at EUR 700. The proposed provisions on standard compensation in the event of power cuts are aimed at amending the provisions in Chapter 6a of the Electricity Market Act on price reduction and compensation because of fault in the supply of electricity. The aim of the introduction of standard compensation for power cuts is to persuade distribution net operators to make an effort to minimize the time for power cuts. (orig.)

[Ageing and work: technical standards].

Science.gov (United States)

De Vito, G; Riva, M A; Meroni, R; Cesana, G C

2010-01-01

Over the last few years, studies on the relationship between ageing and work have attracted growing interest due to the increased probability among workers of developing major health problems as a consequence of ageing of the working population. Negative outcomes for health are possible when an age-related imbalance appears between physical workload and physical work capacity. Interventions based on workload reductions should help to keep workers on the job for as long as allowed by law. Reference masses by age and sex are suggested by the technical standards of the ISO 11228 series, which are also quoted by Italian law D.Lgs. 81/2008, and EN 1005 series, which recommend limits valid also for manual material handling, and pushing and pulling. Decreasing low back pain prevalence or recurrence, in an ageing population with high prevalence of back disorders, could be more effective than many other approaches to enhance workers' quality of life and consequently maintain and improve workers' performance.

Proteomics Standards Initiative: Fifteen Years of Progress and Future Work.

Science.gov (United States)

Deutsch, Eric W; Orchard, Sandra; Binz, Pierre-Alain; Bittremieux, Wout; Eisenacher, Martin; Hermjakob, Henning; Kawano, Shin; Lam, Henry; Mayer, Gerhard; Menschaert, Gerben; Perez-Riverol, Yasset; Salek, Reza M; Tabb, David L; Tenzer, Stefan; Vizcaíno, Juan Antonio; Walzer, Mathias; Jones, Andrew R

2017-12-01

The Proteomics Standards Initiative (PSI) of the Human Proteome Organization (HUPO) has now been developing and promoting open community standards and software tools in the field of proteomics for 15 years. Under the guidance of the chair, cochairs, and other leadership positions, the PSI working groups are tasked with the development and maintenance of community standards via special workshops and ongoing work. Among the existing ratified standards, the PSI working groups continue to update PSI-MI XML, MITAB, mzML, mzIdentML, mzQuantML, mzTab, and the MIAPE (Minimum Information About a Proteomics Experiment) guidelines with the advance of new technologies and techniques. Furthermore, new standards are currently either in the final stages of completion (proBed and proBAM for proteogenomics results as well as PEFF) or in early stages of design (a spectral library standard format, a universal spectrum identifier, the qcML quality control format, and the Protein Expression Interface (PROXI) web services Application Programming Interface). In this work we review the current status of all of these aspects of the PSI, describe synergies with other efforts such as the ProteomeXchange Consortium, the Human Proteome Project, and the metabolomics community, and provide a look at future directions of the PSI.

Experimental stress analysis and fatigue tests of five 24-in. NPS ANSI Standard B16.9 tees

International Nuclear Information System (INIS)

Moore, S.E.; Hayes, J.K.; Weed, R.A.

1985-03-01

Experimental stress analyses and low-cycle fatigue tests of five 24-in. nominal pipe size American National Standards Institute (ANSI) Standard B16.9 forged tees are documented in this report. The tees, designated as Oak Ridge National Laboratory tees T10, T11, T12, T13, and T16, were tested under subcontract at Combustion Engineering, Inc. in Chattanooga, Tennessee. Experimental stress analyses were conducted for 12 individual loadings on each tee. Each test model was instrumented with approx. 225, 1/8-in. three-gage, 45 0 strain rosettes on the inside and outside surfaces; and 6 linear variable differential transformers mounted on special nonflexible holding frames for measuring deflections and rotations of the pipe extensions. Following completion of the strain-gate tests, each tee was fatigue tested to failure with either a fully reversed displacement controlled in-plane bending moment on the branch or a cyclic internal pressure that ranged from a value slightly above zero to about 90% of the nominal yield pressure of the pipe extensions

Preparation of high purity plutonium oxide for radiochemistry instrument calibration standards and working standards

International Nuclear Information System (INIS)

Wong, A.S.; Stalnaker, N.D.

1997-04-01

Due to the lack of suitable high level National Institute of Standards and Technology (NIST) traceable plutonium solution standards from the NIST or commercial vendors, the CST-8 Radiochemistry team at Los Alamos National Laboratory (LANL) has prepared instrument calibration standards and working standards from a well-characterized plutonium oxide. All the aliquoting steps were performed gravimetrically. When a 241 Am standardized solution obtained from a commercial vendor was compared to these calibration solutions, the results agreed to within 0.04% for the total alpha activity. The aliquots of the plutonium standard solutions and dilutions were sealed in glass ampules for long term storage

Procedures and Standards Handbook. Version 3.0. What Works Clearinghouse

Science.gov (United States)

What Works Clearinghouse, 2014

2014-01-01

This "What Works Clearinghouse Procedures and Standards Handbook (Version 3.0)" provides a detailed description of the standards and procedures of the What Works Clearinghouse (WWC). The remaining chapters of this Handbook are organized to take the reader through the basic steps that the WWC uses to develop a review protocol, identify…

An experimental study on decontamination by surface condition

International Nuclear Information System (INIS)

Lee, Young Hae

1974-01-01

Surface decontamination is one of the very important problem to be completely solved in the isotope laboratory where there is always the possibility of radioactive contamination, i.e., on the floors, walls, working tables and benches etc., Isotope laboratories require surface covering of material which can be easily and effectively decontaminated. These experiment were done to find an effective decontamination procedure for kind of surfaces which usually are found in radioisotope laboratories and the best type of surface material, that is, one which is easily decontaminated from the point of view of radiation health and safely. This study is presented to guide radioisotope laboratories in Korea which may need to renovate existing unsafe facilities. In some contaminated facilities entirely new installations may be required. Twelve types of surface material are used for study in this experiment. These include 10 cm square of stainless steel, aluminum, ceramic and mosaic tiles, glass, acrylic, formica board, asphalt tile and coated wood with 4 kinds of paints. Stepwise decontamination was performed with various decontamination procedures following a spill of I 1 31 on the center of the surface material being tested. Twelve different decontamination procedures were tested. These included wet wiping with water and detergent, or dry wiping, or removing with gummed paper. Additional chemical procedures used 10% solution of hydrochloric acid, or surface acid, or ammonium citrate, or potassium iodide, or acetone or carbon tetrachloride. The final testing method was abrasion of the test surfaces. Brief analysis of experimental results on the decontaminability on the tested surface showed: 1. Metallic surfaces such as stainless steel or aluminum, or glass, or a piece of ceramic tile or acrylic are recommended as the surface materials for isotope laboratories because these are easily decontaminated by wet wiping only. 2. Formica board, asphalt tile and wood are not easily

What influences on demonstration experimental work in chemistry classroom?

OpenAIRE

Logar, Ana; Ferk Savec, Vesna

2016-01-01

Teachers and researchers agree that experimental work has a crucial role in teaching and learning of science. The article presents results of a qualitative investigation dealing with factors that influence on the efficiency of primary school students` experimental work in chemistry classroom. The sample consisted of 9 chemistry teachers and 141 randomly selected primary school students (age 13-14 years). Based on the research results a model for effective planning and integration of students`...

The Beyond the standard model working group: Summary report

Energy Technology Data Exchange (ETDEWEB)

G. Azuelos et al.

2004-03-18

In this working group we have investigated a number of aspects of searches for new physics beyond the Standard Model (SM) at the running or planned TeV-scale colliders. For the most part, we have considered hadron colliders, as they will define particle physics at the energy frontier for the next ten years at least. The variety of models for Beyond the Standard Model (BSM) physics has grown immensely. It is clear that only future experiments can provide the needed direction to clarify the correct theory. Thus, our focus has been on exploring the extent to which hadron colliders can discover and study BSM physics in various models. We have placed special emphasis on scenarios in which the new signal might be difficult to find or of a very unexpected nature. For example, in the context of supersymmetry (SUSY), we have considered: how to make fully precise predictions for the Higgs bosons as well as the superparticles of the Minimal Supersymmetric Standard Model (MSSM) (parts III and IV); MSSM scenarios in which most or all SUSY particles have rather large masses (parts V and VI); the ability to sort out the many parameters of the MSSM using a variety of signals and study channels (part VII); whether the no-lose theorem for MSSM Higgs discovery can be extended to the next-to-minimal Supersymmetric Standard Model (NMSSM) in which an additional singlet superfield is added to the minimal collection of superfields, potentially providing a natural explanation of the electroweak value of the parameter {micro} (part VIII); sorting out the effects of CP violation using Higgs plus squark associate production (part IX); the impact of lepton flavor violation of various kinds (part X); experimental possibilities for the gravitino and its sgoldstino partner (part XI); what the implications for SUSY would be if the NuTeV signal for di-muon events were interpreted as a sign of R-parity violation (part XII). Our other main focus was on the phenomenological implications of extra

Estimation of surface absorptivity in laser surface heating process with experimental data

International Nuclear Information System (INIS)

Chen, H-T; Wu, X-Y

2006-01-01

This study applies a hybrid technique of the Laplace transform and finite-difference methods in conjunction with the least-squares method and experimental temperature data inside the test material to predict the unknown surface temperature, heat flux and absorptivity for various surface conditions in the laser surface heating process. In this study, the functional form of the surface temperature is unknown a priori and is assumed to be a function of time before performing the inverse calculation. In addition, the whole time domain is divided into several analysis sub-time intervals and then these unknown estimates on each analysis interval can be predicted. In order to show the accuracy of the present inverse method, comparisons are made among the present estimates, direct results and previous results, showing that the present estimates agree with the direct results for the simulated problem. However, the present estimates of the surface absorptivity deviate slightly from previous estimated results under the assumption of constant thermal properties. The effect of the surface conditions on the surface absorptivity and temperature is not negligible

Making standards work

OpenAIRE

Stigzelius, Ingrid

2009-01-01

Social and environmental standards can function as tools for companies that want to improve their conduct in social and environmental areas in the supply chain. However, relatively little attention has been given to how the adoption of social and environmental standards may influence the actual business practices in the supply chain. The overall aim of this thesis is to examine the institutional context surrounding the adoption of social and environmental standards and how these standards inf...

Sensor for the working surface cleanliness definition in vacuum

Science.gov (United States)

Deulin, E. A.; Mashurov, S. S.; Gatsenko, A. A.

2016-07-01

Modern development of nanotechnology as one of the modern science priority directions is impossible to imagine without the use of vacuum systems and technologies. And the better the vacuum (lower the pressure), the “cleaner” we get a surface, which is very important for nanotechnology. Determination of the cleanliness of the surface or the amount of molecular layers of adsorbed gases on the working surface of the products especially in industry, where the cleanliness of the working surface is a key parameter of the technological process and has a significant influence on the output parameters of the final product is the main goal of this work.

Sensor for the working surface cleanliness definition in vacuum

International Nuclear Information System (INIS)

Deulin, E A; Mashurov, S S; Gatsenko, A A

2016-01-01

Modern development of nanotechnology as one of the modern science priority directions is impossible to imagine without the use of vacuum systems and technologies. And the better the vacuum (lower the pressure), the “cleaner” we get a surface, which is very important for nanotechnology. Determination of the cleanliness of the surface or the amount of molecular layers of adsorbed gases on the working surface of the products especially in industry, where the cleanliness of the working surface is a key parameter of the technological process and has a significant influence on the output parameters of the final product is the main goal of this work. (paper)

Calibration Standards for Surface Topography Measuring Systems down to Nanometric Range

DEFF Research Database (Denmark)

Trumpold, H.; De Chiffre, Leonardo; Andreasen, Jan Lasson

compression and injection moulded plastic negatives and Ni-negatives have been made from which again Ni-positives were produced. The replication processes showed negligible deviations from the Pt and Pa values compared to the primary standards. An important prerequisite is the cleanliness of the surfaces......Background For the precise and accurate measurement of surface topography a whole range of surface detection systems is available. With their application in research and production problems arise due to the lack of traceable standard artefacts for the instrument calibration in X, Y and Z directions...... and for the calibration of filters. Existing ISO standards on calibration specimens are inadequate and limited in that they only cover contacting instruments and only partially the measuring ranges for these instruments. The whole range of non-contacting instruments are not covered despite their increasing use...

Development of measurement standards for verifying functional performance of surface texture measuring instruments

Energy Technology Data Exchange (ETDEWEB)

Fujii, A [Life and Industrial Product Development Department Olympus Corporation, 2951 Ishikawa-machi, Hachiouji-shi, Tokyo (Japan); Suzuki, H [Industrial Marketing and Planning Department Olympus Corporation, Shinjyuku Monolith, 3-1 Nishi-Shinjyuku 2-chome, Tokyo (Japan); Yanagi, K, E-mail: a_fujii@ot.olympus.co.jp [Department of Mechanical Engineering, Nagaoka University of Technology, 1603-1 Kamitomioka-machi, Nagaoka-shi, Niigata (Japan)

2011-08-19

A new measurement standard is proposed for verifying overall functional performance of surface texture measuring instruments. Its surface is composed of sinusoidal surface waveforms of chirp signals along horizontal cross sections of the material measure. One of the notable features is that the amplitude of each cycle in the chirp signal form is geometrically modulated so that the maximum slope is kept constant. The maximum slope of the chirp-like signal is gradually decreased according to movement in the lateral direction. We fabricated the measurement standard by FIB processing, and it was calibrated by AFM. We tried to evaluate the functional performance of Laser Scanning Microscope by this standard in terms of amplitude response with varying slope angles. As a result, it was concluded that the proposed standard can easily evaluate the performance of surface texture measuring instruments.

Non-standard Employment in the Nordics – towards precarious work?

DEFF Research Database (Denmark)

Rasmussen, Stine; Nätti, Jouko; Larsen, Trine Pernille

2018-01-01

This article examines non-standard employment and precariousness in four Nordic countries (Denmark, Sweden, Finland and Norway). Drawing on data from the Labour Force Survey from 1995-2015, the article investigates and compares recent developments of non-standard employment in the countries and w...... to be largely integrated in the Nordic labour markets, it still entails precarious elements in certain countries. Norway and Denmark stand out as less insecure labour markets, while Finland and Sweden have more precariousness associated with non-standard employment.......This article examines non-standard employment and precariousness in four Nordic countries (Denmark, Sweden, Finland and Norway). Drawing on data from the Labour Force Survey from 1995-2015, the article investigates and compares recent developments of non-standard employment in the countries...... and whether fixed-term contracts, temporary agency work, marginal part-time work and solo self-employment have precarious elements (income or job insecurity). We conclude that non-standard employment has remained rather stable in all four countries over time. However, although non-standard employment seems...

Experimental test of the renormalizability consequences of the standard electroweak theory

International Nuclear Information System (INIS)

Bardin, D.Yu.

1984-01-01

The present status of the one-loop radiative corrections calculations in the standard electroweak theory is discussed. The possibilities of experimental tests of the higher order predictions of the standard theory is analysed in view of recent data, inclu-ing CERN p anti pcolcider data on Msub(W) and Msub(Z) measurement. The perspectives of these tests in the near future experiments are discussed

Experimental evaluation of a non-azeotropic working fluid for geothermal heat pump system

International Nuclear Information System (INIS)

Zhao, L.

2004-01-01

Geothermal energy resources are found in many countries. A reasonable and efficient utilization of these resources has been a worldwide concern. The application of geothermal heat pump systems (GHPS) can help increase the efficiency of using geothermal energy and reduce the thermal pollution to the earth surface. However, this is only possible with a proper working fluid. In this paper, a non-azeotropic working fluid (R290/R600a/R123) is presented for a GHPS where geothermal water at 40-45 deg. C and heating network water at 70-80 deg. C serve as the low and high temperature heat sources. Experimental results show that the coefficient of performance (COP) of a GHPS using the working fluid is above 3.5 with the condensation temperature above 80 deg. C and the condensation pressure below 18 bar, while the temperature of the geothermal water is reduced from 40-46 deg. C to 31-36 deg. C

45 CFR 2543.84 - Contract Work Hours and Safety Standards Act.

Science.gov (United States)

2010-10-01

... 45 Public Welfare 4 2010-10-01 2010-10-01 false Contract Work Hours and Safety Standards Act. 2543... OTHER NON-PROFIT ORGANIZATIONS Statutory Compliance § 2543.84 Contract Work Hours and Safety Standards Act. Where applicable, all contracts awarded by recipients in excess of $2000 for construction...

Working group 2: regulatory and standards development

Energy Technology Data Exchange (ETDEWEB)

Bunch, Chad; Lee, Shu; Peters, Mike; Parsonage, Kevin; Saad, Ziad

2011-07-01

This second workshop explored regulatory standards and developments in the pipeline industry. New methods of improved damage prevention for regulators and pipelines to implement were presented. First, incident trends were discussed, using incident analysis to identify the possible causes and solutions of incidents. The determination of realistic goals was attempted. Next, leak detection was discussed with the presentation of current work in annex E which will form part of the new CSA Z662 standard in a few years time. New testing methods such as external methods of leak detection were studied. A third presentation showed the recent development in overpressure protection with reference to the new annex M incorporated in the CSA Z662-11 standard. The last presentation introduced the topic of public safety issues associated with CO2 pipelines with regard to different failure scenarios and the appropriate emergency responses.

Working group 1A - basis for the standard-safety

International Nuclear Information System (INIS)

Whipple, C.

1993-01-01

This paper presents a summary of the progress made by working group 1A (Basis for the Safety Standard) during the Electric Power Research Institute's EPRI Workshop on the technical basis of EPA HLW Disposal Criteria, March 1993. This group discussed the semantics of terms within the standard 40 CFR Part 191, the implementation of this standard, the advanced notice of rulemaking, the issue of emitting carbon-14 through a gaseous pathway, the strategy of dealing with standards for contamination of drinking water and groundwater, the 100,000 year time frame, and the analysis of specific comments. The specific comments dealt with the cost effectiveness of the standard, the dose histogram for populations and individuals, groundwater definition and the underlying technology driver for this standard

Surface Resonance Bands on (001)W: Experimental Dispersion Relations

DEFF Research Database (Denmark)

Willis, R. F.; Feuerbacher, B.; Christensen, N. Egede

1977-01-01

A band of unbound surface states (resonances), located in an energy region above the vacuum threshold corresponding to an energy band gap in the electron states of the bulk crystal, has been observed by angle-resolved secondary-electron-emission spectroscopy. The experimental dispersion behavior...... is in agreement with the two-dimensional band structure of a clean (001)W surface recently proposed by Smith and Mittheiss....

Hydrogen Adsorption on Ga2O3 Surface: A Combined Experimental and Computational Study

Energy Technology Data Exchange (ETDEWEB)

Pan, Yun-xiang; Mei, Donghai; Liu, Chang-jun; Ge, Qingfeng

2011-05-03

In the present work, hydrogen adsorption on the Ga2O3 surfaces was investigated using Fourier transform infrared spectroscopy (FTIR) measurements and periodic density functional theory (DFT) calculations. Both the FTIR and DFT studies suggest that H2 dissociates on the Ga2O3 surfaces, producing OH and GaH species. The FTIR bands at 3730, 3700, 3630 and 3600 cm-1 are attributed to the vibration of the OH species whereas those at 2070 and 1990 cm-1 to the GaH species. The structures of the species detected in experiments are established through a comparison with the DFT calculated stretching frequencies. The O atom of the experimentally detected OH species is believed to originate from the surface O3c atom. On the other hand, the H atom that binds the coordinately unsaturated Ga atom results in the experimentally detected GaH species. Dissociation of H2 on the perfect Ga2O3 surface, with the formation of both OH and GaH species, is endothermic and has an energy barrier of 0.90 eV. In contrast, H2 dissociation on the defective Ga2O3 surface with oxygen vacancies, which mainly produces GaH species, is exothermic, with an energy barrier of 0.61 eV. Accordingly, presence of the oxygen vacancies promotes H2 dissociation and production of GaH species on the Ga2O3 surfaces. Higher temperatures are expected to favor oxygen vacancy creation on the Ga2O3 surfaces, and thereby benefit the production of GaH species. This analysis is consistent with the FTIR results that the bands assigned to GaH species become stronger at higher temperatures. Pacific Northwest National Laboratory is operated by Battelle for the US Department of Energy.

Experimental stress analysis and fatigue tests of five 24-in. NPS ANSI Standard B16. 9 tees. [PWR; BWR

Energy Technology Data Exchange (ETDEWEB)

Moore, S.E.; Hayes, J.K.; Weed, R.A.

1985-03-01

Experimental stress analyses and low-cycle fatigue tests of five 24-in. nominal pipe size American National Standards Institute (ANSI) Standard B16.9 forged tees are documented in this report. The tees, designated as Oak Ridge National Laboratory tees T10, T11, T12, T13, and T16, were tested under subcontract at Combustion Engineering, Inc. in Chattanooga, Tennessee. Experimental stress analyses were conducted for 12 individual loadings on each tee. Each test model was instrumented with approx. 225, 1/8-in. three-gage, 45/sup 0/ strain rosettes on the inside and outside surfaces; and 6 linear variable differential transformers mounted on special nonflexible holding frames for measuring deflections and rotations of the pipe extensions. Following completion of the strain-gate tests, each tee was fatigue tested to failure with either a fully reversed displacement controlled in-plane bending moment on the branch or a cyclic internal pressure that ranged from a value slightly above zero to about 90% of the nominal yield pressure of the pipe extensions.

Experimental study of the response functions of direct-reading instruments measuring surface-area concentration of airborne nanostructured particles

International Nuclear Information System (INIS)

Bau, Sebastien; Witschger, Olivier; Gensdarmes, Francois; Thomas, Dominique

2009-01-01

An increasing number of experimental and theoretical studies focus on airborne nanoparticles (NP) in relation with many aspects of risk assessment to move forward our understanding of the hazards, the actual exposures in the workplace, and the limits of engineering controls and personal protective equipment with regard to NP. As a consequence, generating airborne NP with controlled properties constitutes an important challenge. In parallel, toxicological studies have been carried out, and most of them support the concept that surface-area could be a relevant metric for characterizing exposure to airborne NP. To provide NP surface-area concentration measurements, some direct-reading instruments have been designed, based on attachment rate of unipolar ions to NP by diffusion. However, very few information is available concerning the performances of these instruments and the parameters that could affect their responses. In this context, our work aims at characterizing the actual available instruments providing airborne NP surface-area concentration. The instruments (a- LQ1-DC, Matter Engineering; b-AeroTrak x2122 9000, TSI; c- NSAM, TSI model 3550;) are thought to be relevant for further workplace exposure characterization and monitoring. To achieve our work, an experimental facility (named CAIMAN) was specially designed, built and characterized.

Experimental study of the response functions of direct-reading instruments measuring surface-area concentration of airborne nanostructured particles

Energy Technology Data Exchange (ETDEWEB)

Bau, Sebastien; Witschger, Olivier [Institut National de Recherche et de Securite, INRS, Laboratoire de Metrologie des Aerosols, Rue du Morvan, CS 60027, 54519 Vandoeuvre Cedex (France); Gensdarmes, Francois [Institut de Radioprotection et de Surete Nucleaire, IRSN, Laboratoire de Physique et de Metrologie des Aerosols, BP 68, 91192 Gif-sur-Yvette Cedex (France); Thomas, Dominique [Laboratoire des Sciences du Genie Chimique, LSGC/CNRS, Nancy Universite, BP 2041, 54001 Nancy Cedex (France)], E-mail: sebastien.bau@inrs.fr

2009-05-01

An increasing number of experimental and theoretical studies focus on airborne nanoparticles (NP) in relation with many aspects of risk assessment to move forward our understanding of the hazards, the actual exposures in the workplace, and the limits of engineering controls and personal protective equipment with regard to NP. As a consequence, generating airborne NP with controlled properties constitutes an important challenge. In parallel, toxicological studies have been carried out, and most of them support the concept that surface-area could be a relevant metric for characterizing exposure to airborne NP. To provide NP surface-area concentration measurements, some direct-reading instruments have been designed, based on attachment rate of unipolar ions to NP by diffusion. However, very few information is available concerning the performances of these instruments and the parameters that could affect their responses. In this context, our work aims at characterizing the actual available instruments providing airborne NP surface-area concentration. The instruments (a- LQ1-DC, Matter Engineering; b-AeroTrak{sup x2122} 9000, TSI; c- NSAM, TSI model 3550;) are thought to be relevant for further workplace exposure characterization and monitoring. To achieve our work, an experimental facility (named CAIMAN) was specially designed, built and characterized.

Experimental limits from ATLAS on Standard Model Higgs production.

CERN Multimedia

ATLAS, collaboration

2012-01-01

Experimental limits from ATLAS on Standard Model Higgs production in the mass range 110-600 GeV. The solid curve reflects the observed experimental limits for the production of a Higgs of each possible mass value (horizontal axis). The region for which the solid curve dips below the horizontal line at the value of 1 is excluded with a 95% confidence level (CL). The dashed curve shows the expected limit in the absence of the Higgs boson, based on simulations. The green and yellow bands correspond (respectively) to 68%, and 95% confidence level regions from the expected limits. Higgs masses in the narrow range 123-130 GeV are the only masses not excluded at 95% CL

A virtual experimenter to increase standardization for the investigation of placebo effects

Directory of Open Access Journals (Sweden)

Bjoern Horing

2016-07-01

Full Text Available Abstract Background Placebo effects are mediated by expectancy, which is highly influenced by psychosocial factors of a treatment context. These factors are difficult to standardize. Furthermore, dedicated placebo research often necessitates single-blind deceptive designs where biases are easily introduced. We propose a study protocol employing a virtual experimenter – a computer program designed to deliver treatment and instructions – for the purpose of standardization and reduction of biases when investigating placebo effects. Methods To evaluate the virtual experimenter’s efficacy in inducing placebo effects via expectancy manipulation, we suggest a partially blinded, deceptive design with a baseline/retest pain protocol (hand immersions in hot water bath. Between immersions, participants will receive an (actually inert medication. Instructions pertaining to the medication will be delivered by one of three metaphors: The virtual experimenter, a human experimenter, and an audio/text presentation (predictor “Metaphor”. The second predictor includes falsely informing participants that the medication is an effective pain killer, or correctly informing them that it is, in fact, inert (predictor “Instruction”. Analysis will be performed with hierarchical linear modelling, with a sample size of N = 50. Results from two pilot studies are presented that indicate the viability of the pain protocol (N = 33, and of the virtual experimenter software and placebo manipulation (N = 48. Discussion It will be challenging to establish full comparability between all metaphors used for instruction delivery, and to account for participant differences in acceptance of their virtual interaction partner. Once established, the presence of placebo effects would suggest that the virtual experimenter exhibits sufficient cues to be perceived as a social agent. He could consequently provide a convenient platform to investigate effects of

Standard Specification for Steel Blades Used with the Photovoltaic Module Surface Cut Test

CERN Document Server

American Society for Testing and Materials. Philadelphia

2009-01-01

1.1 This specification specifies the recommended physical characteristics of the steel blades required for the surface cut test described in ANSI/UL 1703 (Section 24) and IEC 61730-2 (Paragraph 10.3). 1.2 ANSI/UL 1703 and IEC 61730-2 are standards for photovoltaic module safety testing. 1.3 This standard provides additional fabrication details for the surface cut test blades that are not provided in ANSI/UL 1703 or IEC 61730-2. Surface cut test blades that have out-of-tolerance corner radii or burrs are known to cause erroneous test results, either passes or failures. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

An experimental study of the attachment of bacteria to submerged surfaces in marine environment

International Nuclear Information System (INIS)

Fera, Ph.

1985-09-01

The seasonal variations of the bacterial settling of three materials (stainless steel, aluminium, polycarbonate filters) have been studied inside an open system of circulating seawater (0.7 m.s -1 ). The fixed bacteria counting have been carried out by scanning electron microscopy and epi-fluorescence microscopy. From the results of the first part of this work, it appears that the growth kinetics of the microbial bio-film, and the densities of the bacteria fixed after 15 days of immersion are higher during summer. Qualitatively, the composition of the number of fixed bacteria evolve with immersion time and with the season. The continuous injection of 0.1 ppm of chlorine in the seawater feeding the experimental system, seems not to be sufficient to prevent, for a long time, the settling of a great number of bacteria. The second part of this work deals with the experimental study of the settling of an aluminium surface by a pseudomonas, isolated of the seawater and submitted or not to conditions of preliminary fast. (O.M.)

The development of the American national standard, ''control of radioactive surface contamination on materials, equipment and facilities to be released for uncontrolled use''

International Nuclear Information System (INIS)

Shapiro, J.

1980-01-01

The American National Standard, Control of Radioactive Surface Contamination on Materials, Equipment and Facilities to be Released for Uncontrolled Use, was developed under the procedures of ANSI for ANSI Main Committee N13 (Radiation Protection) by a working group of the Health Physics Society Standards Committee. This standard provides criteria for the control of materials, equipment and facilities contaminated with radioactivity proposed to be released for uncontrolled use. Permissible contamination limits are specified as well as methods assessing the levels of contamination. This paper reviews the proceedings of the Subcommittee on Radioactive Surface Contamination, the comments received by reviewers of the standard, the resolution of the committee, and the bases for reaching the final limits, recommendations, and measurement procedures. (H.K.)

Influence of Decontaminating Agents and Swipe Materials on Laboratory Simulated Working Surfaces Wet Spilled with Sodium Pertechnetate.

Science.gov (United States)

Akchata, Suman; Lavanya, K; Shivanand, Bhushan

2017-01-01

Decontamination of various working surfaces with sodium pertechnetate minor spillage is essential for maintaining good radiation safety practices as well as for regulatory compliance. To observe the influences of decontaminating agents and swipe materials on different type of surfaces used in nuclear medicine laboratory work area wet spilled with 99m-technetium (99mTc) sodium pertechnetate. Lab-simulated working surface materials. Experimental study design. Direct decontamination method on dust-free lab simulated new working surfaces [stainless steel, polyvinyl chloride (PVC), Perspex, resin] using four decontaminating agents [tap water, soap water (SW), Radiacwash, and spirit] with four different swipe material [cotton, tissue paper (TP), Whatman paper (WP), adsorbent sheet (AS)] was taken 10 samples (n = 10) for each group. Parametric test two-way analysis of variance is used with significance level of 0.005, was used to evaluate statistical differences between different group of decontaminating agent and swipe material, and the results are expressed in mean ± SD. Decontamination factor is calculated after five cleaning for each group. A total of 160 samples result calculated using four decontaminating agent (tap water, SW, Radiacwash, and spirit), four swipe material (cotton, TP, WP, and AS) for commonly used surface (stainless steel, PVC, Perspex, resin) using direct method by 10 samples (n = 10) for each group. Tap water is the best decontaminating agent compared with SW, Radiac wash and spirit for the laboratory simulated stainless steel, PVC, and Perspex surface material, whereas in case of resin surface material, SW decontaminating agent is showing better effectiveness. Cotton is the best swipe material compared to WP-1, AS and TP for the stainless steel, PVC, Perspex, and resin laboratory simulated surface materials. Perspex and stainless steel are the most suitable and recommended laboratory surface material compared to PVC and resin in nuclear medicine

Work functions and surface charges at metallic facet edges

International Nuclear Information System (INIS)

Fall, C.J.; Binggeli, N.; Baldereschi, A.

2002-04-01

The electronic charge densities and work functions at sharp metallic facet edges are determined from ab initio calculations, combined with macroscopic averaging techniques. In particular, we examine how two different work functions coexist at close range near edges between inequivalent facets. The surface ionic relaxation at facet edges is shown to influence appreciably the local electrostatic potential in the vacuum. Various edges between Al(100) and Al(111) facets are studied, as well as between Na(110) facets. We also develop a model of electronic surface dipoles, which accounts for the surface charge transfer between inequivalent facets, and which allows us to predict the influence of the shape and size of a macroscopic crystal on its work functions. (author)

Risk assessment based on current release standards for radioactive surface contamination

International Nuclear Information System (INIS)

Chen, S.Y.

1993-09-01

Standards for uncontrolled releases of radioactive surface contamination have been in existence in the United States for about two decades. Such standards have been issued by various agencies, including the US Department of Energy. This paper reviews the technical basis of published standards, identifies areas in need of revision, provides risk interpretations based on current technical knowledge and the regulatory environment, and offers suggestions for improvements

Experimental and theoretical analysis of defocused CO2 laser microchanneling on PMMA for enhanced surface finish

Science.gov (United States)

Prakash, Shashi; Kumar, Subrata

2017-02-01

The poor surface finish of CO2 laser-micromachined microchannel walls is a major limitation of its utilization despite several key advantages, like low fabrication cost and low time consumption. Defocused CO2 laser beam machining is an effective solution for fabricating smooth microchannel walls on polymer and glass substrates. In this research work, the CO2 laser microchanneling process on PMMA has been analyzed at different beam defocus positions. Defocused processing has been investigated both theoretically and experimentally, and the depth of focus and beam diameter have been determined experimentally. The effect of beam defocusing on the microchannel width, depth, surface roughness, heat affected zone and microchannel profile were examined. A previously developed analytical model for microchannel depth prediction has been improved by incorporating the threshold energy density factor. A semi-analytical model for predicting the microchannel width at different defocus positions has been developed. A semi-empirical model has also been developed for predicting microchannel widths at different defocusing conditions for lower depth values. The developed models were compared and verified by performing actual experiments. Multi-objective optimization was performed to select the best optimum set of input parameters for achieving the desired surface roughness.

Standardization method for alpha and beta surface sources

Energy Technology Data Exchange (ETDEWEB)

Sahagia, M; Grigorescu, E L; Razdolescu, A C; Ivan, C [Institute of Physics and Nuclear Engineering, Institute of Atomic Physics, PO Box MG-6, R-76900 Bucharest, (Romania)

1994-01-01

The installation and method of standardization of large surface alpha and beta sources are presented. A multiwire, flow-type proportional counter and the associated electronics is used. The counter is placed in a lead-shield. The response of the system in (s[sup -1]/Bq) or (s[sup -1]/(particle x s[sup -1])) was determined for [sup 241] Am, [sup 239] Pu, [sup 147] Pm, [sup 204] Tl, [sup 90](Sr+Y) and [sup 137] Cs using standard sources with different dimensions, from some mm[sup 2] to 180 x 220 mm[sup 2]. The system was legally attested for expanded uncertainties of +7%. (Author).

Stability of Working Reference Standards for Hybrid K-Edge Densitometer Quality Assurance

International Nuclear Information System (INIS)

Guzzardo, T.; Pickett, C.A.; McElroy, R.; Croft, S.; Garrison, J.; Venkataraman, R.

2015-01-01

The relatively short working life of aqueous solution standards of actinides for the calibration and quality control of Hybrid K-Edge Densitometer (HKED) measurements necessitates the development of a stable matrix material less susceptible to degradation. Degradation in the form of evaporation, radiolysis, settling, sloshing, and sediment formation can all reduce the reliability and working life of an aqueous standard. These factors make aqueous solutions inadequate for long-term quality assurance measurements designed to detect weak or subtle trends in system performance. Epoxy, studied here, is an alternative matrix material that may be less vulnerable to degradation. An additional benefit of epoxy is that standards can easily be characterized as sealed sources which allows for simplified administrative controls during shipping and storage. The stability of working reference standards consisting of U 3 O 8 in an epoxy matrix for use in the HKED has been tracked for over three years through repeated X-ray Fluorescence (XRF) and K-Edge (KED) measurements. A set of six epoxy standards ranging in concentration from 1 g/l to 76 g/l uranium were determined to be stable, within the expected accuracy of the system, over the period of analysis. During this time, no effort was made to enhance the stability of the epoxy standards; the radial measurement position was not controlled and in the middle of the analysis period the HKED system and standards were shipped from the vendor's factory to the customer. Epoxy standards afford numerous benefits over those created from aqueous solutions and should be considered when developing HKED standards for quality assurance measurements. The stability of the epoxy allows the development of working standards of a stability and robustness sufficient for use in a proposed international round-robin exercise based on the exchange of such standards. (author)

Standard Test Method for Hydrophobic Surface Films by the Atomizer Test

CERN Document Server

American Society for Testing and Materials. Philadelphia

1965-01-01

1.1 This test method covers the detection of the presence of hydrophobic (nonwetting) films on surfaces and the presence of hydrophobic organic materials in processing ambients. When properly conducted, the test will enable detection of fractional molecular layers of hydrophobic organic contaminants. On very rough or porous surfaces the sensitivity of the test may be significantly decreased. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Experimental studies of microwave interaction with a plasma-covered planar conducting surface

International Nuclear Information System (INIS)

Destler, W.W.; Rodgers, J.; DeGrange, J.E.; Segalov, Z.

1990-01-01

The authors present experimental studies of the reflection and absorption of microwave radiation from a plasma-covered planar conducting surface. In the experiments, microwave radiation from both highpower, short pulse (10 GHz, 100 MW, 30 ns) and low power (10 GHz, 10 mW, CW) sources is radiated at a 30 cm diameter conducting plate. A time-varying plasma is created on the surface of the conductor by 19 coaxial plasma guns embedded in the surface of the plate and discharged using a fast-rise capacitor bank. The plasma density distribution on the conducting surface is a function of time and the charging voltage on the capacitor bank. Incident and reflected microwave radiation has been measured for a wide variety of experimental conditions

Experimental Investigations on Microshock Waves and Contact Surfaces

Science.gov (United States)

Kai, Yun; Garen, Walter; Teubner, Ulrich

2018-02-01

The present work reports on progress in the research of a microshock wave. Because of the lack of a good understanding of the propagation mechanism of the microshock flow system (shock wave, contact surface, and boundary layer), the current work concentrates on measuring microshock flows with special attention paid to the contact surface. A novel setup involving a glass capillary (with a 200 or 300 μ m hydraulic diameter D ) and a high-speed magnetic valve is applied to generate a shock wave with a maximum initial Mach number of 1.3. The current work applies a laser differential interferometer to perform noncontact measurements of the microshock flow's trajectory, velocity, and density. The current work presents microscale measurements of the shock-contact distance L that solves the problem of calculating the scaling factor Sc =Re ×D /(4 L ) (introduced by Brouillette), which is a parameter characterizing the scaling effects of shock waves. The results show that in contrast to macroscopic shock waves, shock waves at the microscale have a different propagation or attenuation mechanism (key issue of this Letter) which cannot be described by the conventional "leaky piston" model. The main attenuation mechanism of microshock flow may be the ever slower moving contact surface, which drives the shock wave. Different from other measurements using pressure transducers, the current setup for density measurements resolves the whole microshock flow system.

The experimental field work as practical learning method

Directory of Open Access Journals (Sweden)

Nicolás Fernández Losa

2014-11-01

Full Text Available This paper describes a teaching experience about experimental field work as practical learning method implemented in the subject of Organizational Behaviour. With this teaching experience we pretend to change the practical training, as well as in its evaluation process, in order to favour the development of transversal skills of students. For this purpose, the use of a practice plan, tackled through an experimental field work and carried out with the collaboration of a business organization within a work team (as organic unity of learning, arises as an alternative to the traditional method of practical teachings and allows the approach of business reality into the classroom, as well as actively promote the use of transversal skills. In particular, we develop the experience in three phases. Initially, the students, after forming a working group and define a field work project, should get the collaboration of a nearby business organization in which to obtain data on one or more functional areas of organizational behaviour. Subsequently, students carry out the field work with the realization of the scheduled visits and elaboration of a memory to establish a diagnosis of the strategy followed by the company in these functional areas in order to propose and justify alternative actions that improve existing ones. Finally, teachers assess the different field work memories and their public presentations according to evaluation rubrics, which try to objectify and unify to the maximum the evaluation criteria and serve to guide the learning process of students. The results of implementation of this teaching experience, measured through a Likert questionnaire, are very satisfactory for students.

Experimental Study on Tribological Properties of Laser Textured 45 Steel Surface

Directory of Open Access Journals (Sweden)

Li Zhi Peng

2016-01-01

Full Text Available In order to study the influence of pits’ size parameters on the tribological properties of textured friction pairs, using the Nd:YAG laser micro machining system and the “single pulse at the same point, interval more times” processing technics to process the pits on the surface of 45 steel. The dimension parameters of pits texture were obtained by orthogonal experimental design. The tribological experiment of GCr15 pin/45 steel disc was carried out by UMT-2 test machine. The surface morphology of the specimens was analyzed by using scanning electron microscopy. The experimental results show that the pits texture on the surface of 45 steel can effectively reduce the friction coefficient and the wear on the condition of oil-rich lubrication. The textured specimen with diameter 60μm, depth 6μm and surface density 10% has the lowest friction coefficient, and the friction coefficient is reduced by 21% compared with the smooth specimen. By analyzing the wear morphology on the surface of 45 steel, it is found that the surface of pits texture can obviously reduce the wear.

Bias Corrections for Standardized Effect Size Estimates Used with Single-Subject Experimental Designs

Science.gov (United States)

Ugille, Maaike; Moeyaert, Mariola; Beretvas, S. Natasha; Ferron, John M.; Van den Noortgate, Wim

2014-01-01

A multilevel meta-analysis can combine the results of several single-subject experimental design studies. However, the estimated effects are biased if the effect sizes are standardized and the number of measurement occasions is small. In this study, the authors investigated 4 approaches to correct for this bias. First, the standardized effect…

OIL DECONTAMINATION OF BOTTOM SEDIMENTS EXPERIMENTAL WORK RESULTS

Directory of Open Access Journals (Sweden)

Lushnikov Sergey V.

2006-08-01

Full Text Available This article presents the results of experimental work during 2004-2005 on oil decontamination of bottom sediments of Lake Schuchye, situated in the Komi Republic (Northern Russia. The cause of thecontamination were huge oil spills occurred after a series of accidental ruptures on the Harjaga-Usinsk and Vozej-Usinsk oil-pipe lines in 1994. Flotation technology was used for the cleaning of bottom sediments.157 tons of crude oil were removed during the course of 2-year experimental work from an area of 4,1 ha.The content of aliphatic and alicyclic oil hydrocarbons was reduced from 53,3 g/kg to 2,2 g/kg, on average.Hydrobiological investigations revealed that bottom sediments started to be inhabited by benthos organisms, dominantly Oligochaeta. Besides Oligochaeta, Chironomidae maggots and Bivalvia were detected. Theappearance of Macrozoobenthos organisms can serve as a bioindicator of water quality.

Safety standards for near surface disposal and the safety case and supporting safety assessment for demonstrating compliance with the standards

International Nuclear Information System (INIS)

Metcalf, P.

2003-01-01

The report presents the safety standards for near surface disposal (ICRP guidance and IAEA standards) and the safety case and supporting safety assessment for demonstrating compliance with the standards. Special attention is paid to the recommendations for disposal of long-lived solid radioactive waste. The requirements are based on the principle for the same level of protection of future individuals as for the current generation. Two types of exposure are considered: human intrusion and natural processes and protection measures are discussed. Safety requirements for near surface disposal are discussed including requirements for protection of human health and environment, requirements or safety assessments, waste acceptance and requirements etc

Experimental Assessment of Mechanical Night Ventilation on Inner Wall Surfaces

DEFF Research Database (Denmark)

Ji, Wenhui; Heiselberg, Per Kvols; Wang, Houhua

2016-01-01

The cooling potential of night ventilation largely depends on the heat exchange at the internal room surfaces. During night time, increased heat transfer on a vertical wall is expected due to cool supply air that flows along the internal wall surface from the top of the wall. This paper presents ...... an experimental study of the cooling of wall surfaces in a test room by mechanical night-time ventilation. Significant improvement of indoor thermal environment is presented resulting from the enhanced internal convection heat transfer....

Theoretical studies of the work functions of Pd-based bimetallic surfaces

International Nuclear Information System (INIS)

Ding, Zhao-Bin; Wu, Feng; Wang, Yue-Chao; Jiang, Hong

2015-01-01

Work functions of Pd-based bimetallic surfaces, including mainly M/Pd(111), Pd/M, and Pd/M/Pd(111) (M = 4d transition metals, Cu, Au, and Pt), are studied using density functional theory. We find that the work function of these bimetallic surfaces is significantly different from that of parent metals. Careful analysis based on Bader charges and electron density difference indicates that the variation of the work function in bimetallic surfaces can be mainly attributed to two factors: (1) charge transfer between the two different metals as a result of their different intrinsic electronegativity, and (2) the charge redistribution induced by chemical bonding between the top two layers. The first factor can be related to the contact potential, i.e., the work function difference between two metals in direct contact, and the second factor can be well characterized by the change in the charge spilling out into vacuum. We also find that the variation in the work functions of Pd/M/Pd(111) surfaces correlates very well with the variation of the d-band center of the surface Pd atom. The findings in this work can be used to provide general guidelines to design new bimetallic surfaces with desired electronic properties

40 CFR 63.5743 - What standards must I meet for aluminum recreational boat surface coating operations?

Science.gov (United States)

2010-07-01

... recreational boat surface coating operations? 63.5743 Section 63.5743 Protection of Environment ENVIRONMENTAL... Manufacturing Standards for Aluminum Recreational Boat Surface Coating Operations § 63.5743 What standards must I meet for aluminum recreational boat surface coating operations? (a) For aluminum wipedown solvent...

Students' Hands-on Experimental Work vs Lecture Demonstration in Teaching Elementary School Chemistry.

Science.gov (United States)

Logar, Ana; Ferk-Savec, Vesna

2011-12-01

Science educators have suggested many benefits that accrue from engaging students in experimental activities, therefore, experimental work has a long and distinctive role in chemistry curriculum since. The presented empirical study focuses on the valuation of effectiveness of different forms of experimental work - students' hands-on experimental work vs teacher's lecture demonstration - from the viewpoint of the quality of content knowledge acquisition and knowledge retention in teaching primary school chemistry. 106 primary school students (age 14-15 years) participated in the study. The data was collected via pre- and post- test protocol and two delayed post tests. Additionally 16 students selected from the sample were interviewed. The results indicate that students' content knowledge gained through teacher's demonstration of experiment is better and better knowledge retention takes place in comparison to students' knowledge gained through students' hands-on experimental work. However, most of the inteviewed students stated that they prefered conducting of experiments by themselves in comparison to observation of teacher's demonstration.

Experimental standard molar enthalpies of formation of some 4-alkoxybenzoic acids

International Nuclear Information System (INIS)

Ribeiro da Silva, Manuel A.V.; Lobo Ferreira, Ana I.M.C.; Maciel, Fabrice M.

2010-01-01

The present work is part of a research program on the energetics of the linear 4-n-alkoxybenzoic acids, aiming the study of the enthalpic effect of the introduction of an alkoxy chain in the position 4- of the benzoic acid ring. In this work, we present the results of the thermochemical research on 4-n-alkoxybenzoic acids with the alkoxy chain length n = 2, 4, and 8. The standard (p 0 =0.1MPa) molar enthalpy of formation of crystalline 4-ethoxybenzoic acid, 4-butoxybenzoic acid, and 4-(octyloxy)benzoic acid was measured, at T = 298.15 K, by static-bomb calorimetry. These values, combined with the values of standard molar enthalpies of sublimation, were used to derive the standard molar enthalpies of formation in the gaseous phase.

Thermal hydraulic numerical investigation of the heavy liquid metal free surface of MYRRHA spallation target experimental

International Nuclear Information System (INIS)

Batta, A.; Class, A.

2015-01-01

The first advanced design of accelerator-driven systems (ADS) is currently being built in SCK-CEN (Mol, Belgium): MYRRHA (Multi-purpose hybrid research reactor for high-tech applications). The experiment investigates the free surface design of the MYRRHA target. The free surface lead-bismuth eutectic (LBE) liquid metal experiment is a full-scale model of the concentric MYRRHA target. The design of the target is combined with CFD simulations using a volume of fluid method accounting for mass transfer across the free surface. The model used has been validated with water experimental results. The design of the target enables a high fluid velocity and a stable surface at the beam entry. In the current work, we present numerical results of Star- CD simulations employing a high-resolution interface-capturing scheme in conjunction with the cavitation model for the nominal operation conditions. Thermal hydraulic of the target is considered for the nominal flow rate and nominal heat load. Results show that the target has a very stable free surface configuration for the considered flow rate and heat load

Surface moisture measurement system acceptance testing work plan

International Nuclear Information System (INIS)

Ritter, G.A.

1996-01-01

This work plan addresses testing of the Surface Moisture Measurement System (SMMS) at the Fuels and Materials Examination Facility (FMEF). The purpose of this plan is to define the scope of work, identify organizational responsibilities, describe test control requirements, and provide estimated costs and schedule associated with acceptance testing

Standard test method for calibration of surface/stress measuring devices

CERN Document Server

American Society for Testing and Materials. Philadelphia

1997-01-01

Return to Contents page 1.1 This test method covers calibration or verification of calibration, or both, of surface-stress measuring devices used to measure stress in annealed and heat-strengthened or tempered glass using polariscopic or refractometry based principles. 1.2 This test method is nondestructive. 1.3 This test method uses transmitted light, and therefore, is applicable to light-transmitting glasses. 1.4 This test method is not applicable to chemically tempered glass. 1.5 Using the procedure described, surface stresses can be measured only on the “tin” side of float glass. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

The Origin of Mercury's Surface Composition, an Experimental Investigation

Science.gov (United States)

Boujibar, A.; Righter, K.; Rapp, J. F.; Ross, D. K.; Pando, K. M.; Danielson, L. R.; Fontaine, E.

2016-01-01

Introduction: Results from MESSENGER spacecraft have confirmed the reduced nature of Mercury, based on its high core/mantle ratio and its FeO-poor and S-rich surface. Moreover, high resolution images revealed large volcanic plains and abundant pyroclastic deposits, suggesting major melting stages of the Mercurian mantle. In addition, MESSENGER has provided the most precise data to date on major elemental compositions of Mercury's surface. These results revealed considerable chemical heterogeneities that suggested several stages of differentiation and re-melting processes. This interpretation was challenged by our experimental previous study, which showed a similar compositional variation in the melting products of enstatite chondrites, which are a possible Mercury analogue. However, these experimental melts were obtained over a limited range of pressure (1 bar to 1 gigapascal) and were not compared to the most recent elemental maps. Therefore, here we extend the experimental dataset to higher pressures and perform a more quantitative comparison with Mercury's surface compositions measured by MESSENGER. In particular, we test whether these chemical heterogeneities result from mixing between polybaric melts. Our experiments and models show that the majority of chemical diversity of Mercury's surface can result from melting of a primitive mantle compositionally similar to enstatite chondrites in composition at various depths and degrees of melting. The high-Mg region's composition is reproduced by melting at high pressure (3 gigapascals) (Tab. 1), which is consistent with previous interpretation as being a large degraded impact basin based on its low elevation and thin average crust. While low-Mg NVP (North Volcanic Plains) are the result of melting at low pressure (1 bar), intermediate-Mg NVP, Caloris Basin and Rachmaninoff result from mixing of a high-pressure (3 gigapascals) and low-pressure components (1 bar for Rachmaninoff and 1 gigapascal for the other regions

Surface science techniques

CERN Document Server

Bracco, Gianangelo

2013-01-01

The book describes the experimental techniques employed to study surfaces and interfaces. The emphasis is on the experimental method. Therefore all chapters start with an introduction of the scientific problem, the theory necessary to understand how the technique works and how to understand the results. Descriptions of real experimental setups, experimental results at different systems are given to show both the strength and the limits of the technique. In a final part the new developments and possible extensions of the techniques are presented. The included techniques provide microscopic as well as macroscopic information. They cover most of the techniques used in surface science.

EXPERIMENTAL VALIDATION OF CUMULATIVE SURFACE LOCATION ERROR FOR TURNING PROCESSES

Directory of Open Access Journals (Sweden)

Adam K. Kiss

2016-02-01

Full Text Available The aim of this study is to create a mechanical model which is suitable to investigate the surface quality in turning processes, based on the Cumulative Surface Location Error (CSLE, which describes the series of the consecutive Surface Location Errors (SLE in roughing operations. In the established model, the investigated CSLE depends on the currently and the previously resulted SLE by means of the variation of the width of cut. The phenomenon of the system can be described as an implicit discrete map. The stationary Surface Location Error and its bifurcations were analysed and flip-type bifurcation was observed for CSLE. Experimental verification of the theoretical results was carried out.

The overall heat transfer characteristics of a double pipe heat exchanger: comparison of experimental data with predictions of standard correlations

International Nuclear Information System (INIS)

Mehrabian, M. A.; Mansouri, S. H.; Sheikhzadeh, G. A.

2002-01-01

The single-phase flow and thermal performance of a double pipe heat exchanger are examined by experimental methods. The working fluid is water at atmospheric pressure. Temperature measurements at the inlet and outlet of the two streams and also at an intermediate point half way between the inlet and outlet is made, using copper-constantan thermocouple wires. Mass flow rates for each stream are also measured using calibrated ratemeters. Heat is supplied to the inner tube stream by an immersion heater. The overall heat transfer coefficients are inferred from the measured data. The heat transfer coefficient of the inner tube flow (circular cross section) is calculated using the standard correlations. The heat transfer coefficient of the outer tube flow (annular cross section) is then deduced.Higher heat transfer coefficients are reported in the laminar flow regime in comparison to the predictions of standard correlations for straight and smooth tubes. The reasons for this discrepancy are identified and discussed. Experimental errors in measuring temperatures and mass flow rates are studied and their effects on the heat transfer coefficients are estimated. Experimental results for the range of operating conditions used in this work show that the outer tube side heat transfer coefficients are smaller than the inner side heat transfer coefficients by a factor of almost 1.5 and 3.4 in counter flow and parallel flow arrangements, respectively. The agreement with predictions is very good for the counter flow arrangement, but not very good for the parallel flow arrangement

Non-standard work schedules, gender, and parental stress

Czech Academy of Sciences Publication Activity Database

Lozano, M.; Hamplová, Dana; Le Bourdais, C.

2016-01-01

Roč. 34, č. 9 (2016), s. 259-284 ISSN 1435-9871 R&D Projects: GA ČR(CZ) GA14-15008S Institutional support: RVO:68378025 Keywords : stress * employment * non-standard work hours Subject RIV: AO - Sociology, Demography Impact factor: 1.320, year: 2016 http://www.demographic-research.org/volumes/vol34/9/ default .htm

Non-standard work schedules, gender, and parental stress

Czech Academy of Sciences Publication Activity Database

Lozano, M.; Hamplová, Dana; Le Bourdais, C.

2016-01-01

Roč. 34, č. 9 (2016), s. 259-284 ISSN 1435-9871 R&D Projects: GA ČR(CZ) GA14-15008S Institutional support: RVO:68378025 Keywords : stress * employment * non-standard work hours Subject RIV: AO - Sociology, Demography Impact factor: 1.320, year: 2016 http://www.demographic-research.org/volumes/vol34/9/default.htm

Surface Coating of Plastic Parts for Business Machines (Industrial Surface Coating): New Source Performance Standards (NSPS)

Science.gov (United States)

Learn more about the new source performance standards (NSPS) for surface coating of plastic parts for business machines by reading the rule summary and history and finding the code of federal regulations as well as related rules.

Standard Test Method for Hydrophobic Surface Films by the Water-Break Test

CERN Document Server

American Society for Testing and Materials. Philadelphia

2002-01-01

1.1 This test method covers the detection of the presence of hydrophobic (nonwetting) films on surfaces and the presence of hydrophobic organic materials in processing ambients. When properly conducted, the test will enable detection of molecular layers of hydrophobic organic contaminants. On very rough or porous surfaces, the sensitivity of the test may be significantly decreased. 1.2 The values stated in SI units are to be regarded as the standard. The inch-pound values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Elements of Experimental Work in the Upper Secondary School

DEFF Research Database (Denmark)

Josephsen, Jens

1999-01-01

The objectives for the Danish second year upper secondary school chemistry course are intended to contribute to a general understanding of science as well as to the preparation for university studies in science subjects. At the university, knowledge of the students’ entrance qualifications...... is important for freshman teaching planning. The practical work of 4 different classes has been characterised by studying laboratory exercise manuals. An estimate has been given of to what extent the qualitative goals for the practical work can be reached. An outline of elements of experimental work used...

Experimental and theoretical studies of bombardment induced surface morphology changes

International Nuclear Information System (INIS)

Carter, G.; Nobes, M.J.; Williams, J.S.

1980-01-01

In this review results of experimental and theoretical studies of solid surface morphology changes due to ion bombardment are discussed. An attempt is undertaken to classify the observed specific features of a structure, generated by ion bombardment [ru

Photoelectric work function measurement of a cesiated metal surface and its correlation with the surface-produced H- ion flux

International Nuclear Information System (INIS)

Wada, M.; Berkner, K.H.; Pyle, R.V.; Stearns, J.W.

1982-09-01

For application in plasma heating, fueling, and current drive of magnetic fusion devices, high current negative deuterium ion sources for intense neutral beam injectors are being developed using efficient production of negative hydrogen isotope ions on low work function metal surfaces imbedded in hydrogen plasmas. In order to investigate the correlation between work function and negative hydrogen ion production, photoelectron emission from a cesiated metal surface, which is immersed in a hydrogen plasma with an electron density less than 5 x 10 10 /cc, was measured in the photon energy range of 1.3 to 4.1 eV. The work function determination was based on Fowler's analysis, and at the optimum coverage a work function of less than 1.5 eV was observed for a Cs-Cu surface. Measured values of work functions for different Cs coverages were compared to the negative hydrogen currents produced at the metal surface in the discharge; the surface production of negative hydrogen ion current is monotonically increasing with decreasing work function

Characterisation of surface roughness for ultra-precision freeform surfaces

International Nuclear Information System (INIS)

Li Huifen; Cheung, C F; Lee, W B; To, S; Jiang, X Q

2005-01-01

Ultra-precision freeform surfaces are widely used in many advanced optics applications which demand for having surface roughness down to nanometer range. Although a lot of research work has been reported on the study of surface generation, reconstruction and surface characterization such as MOTIF and fractal analysis, most of them are focused on axial symmetric surfaces such as aspheric surfaces. Relative little research work has been found in the characterization of surface roughness in ultra-precision freeform surfaces. In this paper, a novel Robust Gaussian Filtering (RGF) method is proposed for the characterisation of surface roughness for ultra-precision freeform surfaces with known mathematic model or a cloud of discrete points. A series of computer simulation and measurement experiments were conducted to verify the capability of the proposed method. The experimental results were found to agree well with the theoretical results

Experimental study of a high-efficiency low-emission surface combustor-heater

International Nuclear Information System (INIS)

Xiong, Tian-yu; Khinkis, M.J.; Fish, F.F.

1991-01-01

The surface combustor-heater is a combined combustion/heat-transfer device in which the heat-exchange surfaces are embedded in a stationary bed of refractory material where gaseous fuel is burned. Because of intensive heat radiation from the hot solid particles and enhanced heat convection from the gas flow to the heat-exchange tubes, heat transfer is significantly intensified. Removing heat simultaneously with the combustion process has the benefit of reducing the combustion temperature, which suppresses NO x formation. A basic experimental study was conducted on a 60-kW bench-scale surface combustor-heater with two rows of water-cooled tube coils to evaluate its performance and explore the mechanism of combined convective-radiative heat transfer and its interaction with combustion in the porous matrix. Combustion stability in the porous matrix, heat-transfer rates, emissions, and pressure drop through the unit have been investigated for the variable parameters of operation and unit configurations. Experimental results have demonstrated that high combustion intensity (up to 2.5 MW/m 2 ), high heat-transfer rates (up to 310 kW/m 2 ), high density of energy conversion (up to 8 MW/m 3 ), as well as ultra-low emissions (NO x and CO as low as 15 vppm*) have been achieved. The excellent performance of the test unit and the extensive data obtained from the present experimental study provide the basis for further development of high-efficiency and ultra low-emission water heaters, boilers, and process heaters based on the surface combustor-heater concept. 4 refs., 16 figs

THE STANDARD MILLING TIME OF FLAT SURFACES WITHOUT OUTLINE RESTRICTIONS

Directory of Open Access Journals (Sweden)

Leszek Skoczylas

2016-09-01

Full Text Available Knowing the standard operating times of technological operations is essential element in the business operations of every production enterprise. It is the basis for establishing the production capacity, planning the production schedule, or even calculating costs. The article presents a variety of methods used in the calculation of standard worktime of technological operations. An especially important distinction was made between calculating the total machining time and the actual cutting time. Through the examination of various machined flat surfaces, the results of worktime calculations from CATIA and the authored mathematical model are presented.

DRDC Ottawa working standard for biological dosimetry

International Nuclear Information System (INIS)

Segura, T.M.; Prud'homme-Lalonde, L.; Thorleifson, E.; Lachapelle, S.; Mullins, D.; Qutob, S.; Wilkinson, D.

2005-07-01

This Standard provides quality assurance, quality control, and evaluation of the performance criteria for the purpose of accreditation of the Radiation Biology laboratory at Defence Research and Development Canada - Ottawa (DRDC Ottawa) using biological dosimetry to predict radiation exposure doses. The International Standard (ISO 19238) and the International Atomic Energy Association (IAEA) Technical Report Series No. 405 are used as guiding documents in preparation of this working document specific to the DRDC Ottawa Radiation Biology Laboratory. This Standard addresses: 1. The confidentiality of personal information, for the customer and the service laboratory; 2. The laboratory safety requirements; 3. The calibration sources and calibration dose ranges useful for establishing the reference dose-effect curves allowing the dose estimation from chromosome aberration frequency, and the minimum detection levels; 4. Transportation criteria for shipping of test samples to the laboratory; 5. Preparation of samples for analysis; 6. The scoring procedure for unstable chromosome aberrations used for biological dosimetry; 7. The criteria for converting a measured aberration frequency into an estimate of absorbed dose; 8. The reporting of results; 9. The quality assurance and quality control plan for the laboratory; and 10. Informative annexes containing examples of a questionnaire, instructions for customers, a data sheet for recording aberrations, a sample report and other supportive documents. (author)

DRDC Ottawa working standard for biological dosimetry

Energy Technology Data Exchange (ETDEWEB)

Segura, T M; Prud' homme-Lalonde, L [Defence Research and Development Canada, Ottawa, Ontario (Canada); Thorleifson, E [Health Canada, Gatineau, Quebec (Canada); Lachapelle, S; Mullins, D [JERA Consulting (Canada); Qutob, S [Health Canada, Gatineau, Quebec (Canada); Wilkinson, D

2005-07-15

This Standard provides quality assurance, quality control, and evaluation of the performance criteria for the purpose of accreditation of the Radiation Biology laboratory at Defence Research and Development Canada - Ottawa (DRDC Ottawa) using biological dosimetry to predict radiation exposure doses. The International Standard (ISO 19238) and the International Atomic Energy Association (IAEA) Technical Report Series No. 405 are used as guiding documents in preparation of this working document specific to the DRDC Ottawa Radiation Biology Laboratory. This Standard addresses: 1. The confidentiality of personal information, for the customer and the service laboratory; 2. The laboratory safety requirements; 3. The calibration sources and calibration dose ranges useful for establishing the reference dose-effect curves allowing the dose estimation from chromosome aberration frequency, and the minimum detection levels; 4. Transportation criteria for shipping of test samples to the laboratory; 5. Preparation of samples for analysis; 6. The scoring procedure for unstable chromosome aberrations used for biological dosimetry; 7. The criteria for converting a measured aberration frequency into an estimate of absorbed dose; 8. The reporting of results; 9. The quality assurance and quality control plan for the laboratory; and 10. Informative annexes containing examples of a questionnaire, instructions for customers, a data sheet for recording aberrations, a sample report and other supportive documents. (author)

Experimental study of pressure drop characteristics of venturi scrubber working at self-priming mode

International Nuclear Information System (INIS)

Wang Meng; Sun Zhongning; Gu Haifeng; Guo Xueqing; Yu Yong

2012-01-01

The pressure drop characteristics of Venturi scrubber working at self-priming mode were studied experimentally. The test sections were smooth glass scrubbers, with air and water as the working medium. The results show that the trends of empirical formula are more consistent with that of the experimental results, but the relative error is large, up to ±50% or more. The experimental correlation is proposed based on the experimental research, and the calculated results of which can well predict the experimental data and the relative error is within ±15%. (authors)

Experimental survey of the potential energy surfaces associated with fission

International Nuclear Information System (INIS)

Britt, H.C.

1980-01-01

Progress in the experimental determination of the properties of the potential energy surface associated with fission is reviewed. The importance of nuclear symmetry effects on the calculation of fission widths is demonstrated. Evidence is presented for the fragmentation of the mass-asymmetric second barrier in the thorium region and the axial asymmetric first barrier in the californium region. Detailed analyses of experimental data suggest the presence of two parallel second barriers; the normal mass-asymmetric, axial-symmetric barrier and a slightly higher mass-symmetric, axial-asymmetric barrier. Experimental barrier parameters are determined systematically and compared with calculations from various theoretical models. Techniques for expanding fission probability measurements to higher energies are discussed. (author)

Implementing healthy work environment standards in an academic workplace: An update.

Science.gov (United States)

Harmon, Rebecca B; DeGennaro, Gina; Norling, Meg; Kennedy, Christine; Fontaine, Dorrie

In 2005 the American Association of Critical Care Nurses defined six Healthy Work Environment (HWE) standards for the clinical setting (AACN, 2005), which were reaffirmed and expanded in 2016 (AACN, 2016). These clinical standards were adapted for use in the academic setting by Fontaine, Koh, and Carroll in 2012. The intention of this article is threefold: to present a revised version of the academic workplace standards which are appropriate for all School of Nursing (SON) employees, staff as well as faculty; to proposes the addition of a seventh standard, self-care, which provides the foundation for all standards; and to describe the continuing implementation of these seven standards at the University of Virginia School of Nursing (UVA SON). Copyright © 2017 Elsevier Inc. All rights reserved.

The effects of work surface hardness on mechanical stress, muscle activity, and wrist postures.

Science.gov (United States)

Kim, Jeong Ho; Aulck, Lovenoor; Trippany, David; Johnson, Peter W

2015-01-01

Contact pressure is a risk factor which can contribute to musculoskeletal disorders. The objective of the present study was to determine whether a work surface with a soft, pliable front edge could reduce contact pressure, muscle activity, and subjective musculoskeletal comfort, and improve wrist posture relative to a conventional, hard work surface. In a repeated-measures blinded experiment with eighteen subjects (8 females and 10 males), contact pressure, wrist posture, typing productivity, perceived fatigue, wrist and shoulder muscle activity, and subjective comfort were compared between the two different work surfaces during keyboard use, mouse use and mixed mouse and keyboard use. The results showed that across the three modes of computer work, the contact pressure was lower on the soft-edge work surface compared to the conventional work surface (p's work surfaces. Given the significant reduction in contact pressure and corresponding lower ratings in perceived fatigue, the soft-edge work surface subjectively and objectively improved measures of contact stress which may reduce physical exposures associated with the onset and development of musculoskeletal disorders.

  Representations at Work: A national Standard for Electronic Health Records

DEFF Research Database (Denmark)

Bossen, Claus

2006-01-01

  Representations are at work in IT technology. As plans of and for work, they enable cooperation, coordination, accountability and control, which have to be balanced off against each other. The article describes a standard developed for electronic health records (EHR) and the results of a test...

An Experimental Investigation of Unsteady Surface Pressure on an Airfoil in Turbulence

Science.gov (United States)

Mish, Patrick F.; Devenport, William J.

2003-01-01

Measurements of fluctuating surface pressure were made on a NACA 0015 airfoil immersed in grid generated turbulence. The airfoil model has a 2 ft chord and spans the 6 ft Virginia Tech Stability Wind Tunnel test section. Two grids were used to investigate the effects of turbulence length scale on the surface pressure response. A large grid which produced turbulence with an integral scale 13% of the chord and a smaller grid which produced turbulence with an integral scale 1.3% of the chord. Measurements were performed at angles of attack, alpha from 0 to 20 . An array of microphones mounted subsurface was used to measure the unsteady surface pressure. The goal of this measurement was to characterize the effects of angle of attack on the inviscid response. Lift spectra calculated from pressure measurements at each angle of attack revealed two distinct interaction regions; for omega(sub r) = omega b / U(sub infinity) is less than 10 a reduction in unsteady lift of up to 7 decibels (dB) occurs while an increase occurs for omega(sub r) is greater than 10 as the angle of attack is increased. The reduction in unsteady lift at low omega(sub r) with increasing angle of attack is a result that has never before been shown either experimentally or theoretically. The source of the reduction in lift spectral level appears to be closely related to the distortion of inflow turbulence based on analysis of surface pressure spanwise correlation length scales. Furthermore, while the distortion of the inflow appears to be critical in this experiment, this effect does not seem to be significant in larger integral scale (relative to the chord) flows based on the previous experimental work of McKeough suggesting the airfoils size relative to the inflow integral scale is critical in defining how the airfoil will respond under variation of angle of attack. A prediction scheme is developed that correctly accounts for the effects of distortion when the inflow integral scale is small relative

Simulated BRDF based on measured surface topography of metal

Science.gov (United States)

Yang, Haiyue; Haist, Tobias; Gronle, Marc; Osten, Wolfgang

2017-06-01

The radiative reflective properties of a calibration standard rough surface were simulated by ray tracing and the Finite-difference time-domain (FDTD) method. The simulation results have been used to compute the reflectance distribution functions (BRDF) of metal surfaces and have been compared with experimental measurements. The experimental and simulated results are in good agreement.

Cycle frequency in standard Rock-Paper-Scissors games: Evidence from experimental economics

Science.gov (United States)

Xu, Bin; Zhou, Hai-Jun; Wang, Zhijian

2013-10-01

The Rock-Paper-Scissors (RPS) game is a widely used model system in game theory. Evolutionary game theory predicts the existence of persistent cycles in the evolutionary trajectories of the RPS game, but experimental evidence has remained to be rather weak. In this work, we performed laboratory experiments on the RPS game and analyzed the social-state evolutionary trajectories of twelve populations of N=6 players. We found strong evidence supporting the existence of persistent cycles. The mean cycling frequency was measured to be 0.029±0.009 period per experimental round. Our experimental observations can be quantitatively explained by a simple non-equilibrium model, namely the discrete-time logit dynamical process with a noise parameter. Our work therefore favors the evolutionary game theory over the classical game theory for describing the dynamical behavior of the RPS game.

Anisotropic yield surfaces in bi-axial cyclic plasticity

International Nuclear Information System (INIS)

Rider, R.J.; Harvey, S.J.; Breckell, T.H.

1985-01-01

Some aspects of the behaviour of yield surfaces and work-hardening surfaces occurring in biaxial cyclic plasticity have been studied experimentally and theoretically. The experimental work consisted of subjecting thin-walled tubular steel specimens to cyclic plastic torsion in the presence of sustained axial loads of various magnitudes. The experimental results show that considerable anisotropy is induced when the cyclic shear strains are dominant. Although the true shapes of yield and work-hardening surfaces can be very complex, a mathematical model is presented which includes both anisotropy and Bauschinger effects. The model is able to qualitatively predict the deformation patterns during a cycle of applied plastic shear strain for a range of sustained axial stresses and also indicate the material response to changes in axial stress. (orig.)

Estimation of surface soil moisture and roughness from multi-angular ASAR imagery in the Watershed Allied Telemetry Experimental Research (WATER

Directory of Open Access Journals (Sweden)

S. G. Wang

2011-05-01

Full Text Available Radar remote sensing has demonstrated its applicability to the retrieval of basin-scale soil moisture. The mechanism of radar backscattering from soils is complicated and strongly influenced by surface roughness. Additionally, retrieval of soil moisture using AIEM (advanced integrated equation model-like models is a classic example of underdetermined problem due to a lack of credible known soil roughness distributions at a regional scale. Characterization of this roughness is therefore crucial for an accurate derivation of soil moisture based on backscattering models. This study aims to simultaneously obtain surface roughness parameters (standard deviation of surface height σ and correlation length cl along with soil moisture from multi-angular ASAR images by using a two-step retrieval scheme based on the AIEM. The method firstly used a semi-empirical relationship that relates the roughness slope, Zs (Zs = σ²/cl and the difference in backscattering coefficient (Δσ from two ASAR images acquired with different incidence angles. Meanwhile, by using an experimental statistical relationship between σ and cl, both these parameters can be estimated. Then, the deduced roughness parameters were used for the retrieval of soil moisture in association with the AIEM. An evaluation of the proposed method was performed in an experimental area in the middle stream of the Heihe River Basin, where the Watershed Allied Telemetry Experimental Research (WATER was taken place. It is demonstrated that the proposed method is feasible to achieve reliable estimation of soil water content. The key challenge is the presence of vegetation cover, which significantly impacts the estimates of surface roughness and soil moisture.

Experimental and Theoretical Analysis of Headlight Surface Temperature in an Infrared Heated Stress Relieving Oven

Directory of Open Access Journals (Sweden)

Mustafa MUTLU

2016-04-01

Full Text Available In this study, the IR heated stress relieve oven was experimentally and theoretically examined. In experimental measurements, temperature was measured on headlight surface, placed in IR oven at various conveyor speeds and various distances between IR lamps and headlight surface. In theoretical study, a mathematical model was developed for the headlights surface temperature by using heat transfer theory. The results obtained by the mathematical model and the measurement showed very good agreement with a 6.5 % average error. It is shown that mathematical models can be used to estimate the surface temperatures when the oven is operated under different conditions.

Exploring science teachers' perceptions of experimentation: implications for restructuring school practical work

Science.gov (United States)

Wei, Bing; Li, Xiaoxiao

2017-09-01

It is commonly recognised that practical work has a distinctive and central role in science teaching and learning. Although a large number of studies have addressed the definitions, typologies, and purposes of practical work, few have consulted practicing science teachers. This study explored science teachers' perceptions of experimentation for the purpose of restructuring school practical work in view of science practice. Qualitative interviews were conducted with 87 science teachers at the secondary school level. In the interviews, science teachers were asked to make a comparison between students' experiments and scientific experiments. Eight dimensions of experimentation were generated from the qualitative data analysis, and the distributions of these eight dimensions between the two types of experiments were compared and analysed. An ideal model of practical work was suggested for restructuring practical work at the secondary school level, and some issues related to the effective enactment of practical work were discussed.

Work function and surface stability of tungsten-based thermionic electron emission cathodes

Science.gov (United States)

Jacobs, Ryan; Morgan, Dane; Booske, John

2017-11-01

Materials that exhibit a low work function and therefore easily emit electrons into vacuum form the basis of electronic devices used in applications ranging from satellite communications to thermionic energy conversion. W-Ba-O is the canonical materials system that functions as the thermionic electron emitter commercially used in a range of high-power electron devices. However, the work functions, surface stability, and kinetic characteristics of a polycrystalline W emitter surface are still not well understood or characterized. In this study, we examined the work function and surface stability of the eight lowest index surfaces of the W-Ba-O system using density functional theory methods. We found that under the typical thermionic cathode operating conditions of high temperature and low oxygen partial pressure, the most stable surface adsorbates are Ba-O species with compositions in the range of Ba0.125O-Ba0.25O per surface W atom, with O passivating all dangling W bonds and Ba creating work function-lowering surface dipoles. Wulff construction analysis reveals that the presence of O and Ba significantly alters the surface energetics and changes the proportions of surface facets present under equilibrium conditions. Analysis of previously published data on W sintering kinetics suggests that fine W particles in the size range of 100-500 nm may be at or near equilibrium during cathode synthesis and thus may exhibit surface orientation fractions well described by the calculated Wulff construction.

Lewis basicity, adhesion thermodynamic work and coordinating ability on aminated silicon surfaces

International Nuclear Information System (INIS)

Sánchez, M. Alejandra; Paniagua, Sergio A.; Borge, Ignacio; Viales, Christian; Montero, Mavis L.

2014-01-01

Highlights: • Silicon(1 0 0) surfaces with diamines followed by anchoring of copper complexes over the diamine layer, an approach that could be used for advanced functionalization of semiconducting surfaces. • Lewis basicity (using Fowkes–van Oss–Chaudhury–Good surface tension model) and adhesion thermodynamic work (using chemical force microscopy) were determined. • Higher basicity and thermodynamic work correlate with selective copper acetate monolayer grow. The cyclic voltammetry studies confirm the confined copper redox activity. - Abstract: Silicon(1 0 0) surfaces have been modified with three different amines (aniline, benzylamine and dodecylamine) and diamines (4-aminopyridine, 4-aminomethylpyridine, 1,12-dodecyldiamine). The surface energy was measured by contact angle technique. For Si-diamine surfaces, Lewis basicity (using Fowkes–van Oss–Chaudhury–Good surface tension model) and adhesion thermodynamic work (using chemical force microscopy) were determined. We related these data, the amine/diamine nature and their geometry on the surface (via DFT calculations) with the consequent ability to coordinate copper(II) acetate. Finally, copper(II) acetate monolayers behavior was studied by cyclic voltammetry

Standard practice for exposing and evaluating metals and alloys in surface seawater

CERN Document Server

American Society for Testing and Materials. Philadelphia

2000-01-01

1.1 This practice covers conditions for the exposure of metals, alloys, and other materials in natural surface seawater such as those typically found in bays, harbors, channels, and so forth, as contrasted with deep ocean testing. This practice covers full immersion, tidal zone and related splash, and spray zone exposures. 1.2 This practice sets forth general procedures that should be followed in conducting seawater exposure tests so that meaningful comparisons may be made from one location to another. 1.3 This practice identifies recommended procedures for evaluating the effects of natural surface seawater on the materials exposed. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regula...

Evaluation and Visualization of Surface Defects - a Numerical and Experimental Study on Sheet-Metal Parts

International Nuclear Information System (INIS)

Andersson, A.

2005-01-01

The ability to predict surface defects in outer panels is of vital importance in the automotive industry, especially for brands in the premium car segment. Today, measures to prevent these defects can not be taken until a test part has been manufactured, which requires a great deal of time and expense. The decision as to whether a certain surface is of acceptable quality or not is based on subjective evaluation. It is quite possible to detect a defect by measurement, but it is not possible to correlate measured defects and the subjective evaluation. If all results could be based on the same criteria, it would be possible to compare a surface by both FE simulations, experiments and subjective evaluation with the same result.In order to find a solution concerning the prediction of surface defects, a laboratory tool was manufactured and analysed both experimentally and numerically. The tool represents the area around a fuel filler lid and the aim was to recreate surface defects, so-called 'teddy bear ears'. A major problem with the evaluation of such defects is that the panels are evaluated manually and to a great extent subjectivity is involved in the classification and judgement of the defects. In this study the same computer software was used for the evaluation of both the experimental and the numerical results. In this software the surface defects were indicated by a change in the curvature of the panel. The results showed good agreement between numerical and experimental results. Furthermore, the evaluation software gave a good indication of the appearance of the surface defects compared to an analysis done in existing tools for surface quality measurements. Since the agreement between numerical and experimental results was good, this indicates that these tools can be used for an early verification of surface defects in outer panels

Experimental investigation on hard turning of AISI 4340 steel using cemented coated carbide insert

Science.gov (United States)

Pradeep Kumar, J.; Kishore, K. P.; Ranjith Kumar, M.; Saran Karthick, K. R.; Vishnu Gowtham, S.

2018-02-01

Hard turning is a developing technology that offers many potential advantages compared to grinding, which remains the standard finishing process for critical hardened surfaces. In this work, an attempt has been made to experimentally investigate hard turning of AISI 4340 steel under wet and dry condition using cemented coated carbide insert. Hardness of the workpiece material is tested using Brinell and Rockwell hardness testers. CNC LATHE and cemented coated carbide inserts of designation CNMG 120408 are used for conducting experimental trials. Significant cutting parameters like cutting speed, feed rate and depth of cut are considered as controllable input parameters and surface roughness (Ra), tool wear are considered as output response parameters. Design of experiments is carried out with the help of Taguchi’s L9 orthogonal array. Results of response parameters like surface roughness and tool wear under wet and dry condition are analysed. It is found that surface roughness and tool wear are higher under dry machining condition when compared to wet machining condition. Feed rate significantly influences the surface roughness followed by cutting speed. Depth of cut significantly influences the tool wear followed by cutting speed.

ISO radiation protection standards

International Nuclear Information System (INIS)

Becker, K.; West, N.

1981-01-01

After a brief description of the International Organization for Standardization (ISO) and its Technical Committee (TC) 85 ''Nuclear Energy'', the work of its Sub-Committee (SC) 2 ''Radiation Protection'' is described in some detail. Several international standards on subjects closely related to radiation protection have already been published, for example ISO-361 (Basic radiation protection symbol), ISO-1757 (Photographic dosimeters), ISO-1758 and 1759 (Direct and indirect-reading pocket exposure meters), ISO-2889 (Sampling of airborne radioactive materials), ISO-4037 (X and gamma reference radiations for calibration) and ISO-4071 (Testing of exposure meters and dosimeters). TC 85/SC 2 has currently eight active Working Groups (WG) dealing with 14 standards projects, mostly in advanced stages, in such fields as neutron and beta reference radiations, and X and gamma radiations of high and low dose-rates and high energies for calibration purposes, reference radiations for surface contamination apparatus, ejection systems for gamma radiography apparatus, industrial and laboratory irradiators, lead shielding units, protective clothing, thermoluminescence dosemeters, radioelement gauges, and surface contamination and decontamination. (author)

Functionalization of glassy carbon surface by means of aliphatic and aromatic amino acids. An experimental and theoretical integrated approach

International Nuclear Information System (INIS)

Vanossi, Davide; Benassi, Rois; Parenti, Francesca; Tassinari, Francesco; Giovanardi, Roberto; Florini, Nicola; De Renzi, Valentina; Arnaud, Gaelle; Fontanesi, Claudio

2012-01-01

Highlights: ► Glassy carbon is functionalized via electrochemical assisted grafting of amino acids. ► The grafting mechanism is suggested to involve the “zwitterionic” species. ► DFT calculations allowed to determine the electroactive species. ► An original grafting mechanism is proposed. - Abstract: Glassy carbon (GC) electrode surfaces are functionalized through electrochemical assisted grafting, in oxidation regime, of six amino acids (AA): β-alanine (β-Ala), L-aspartic acid (Asp), 11-aminoundecanoic acid (UA), 4-aminobenzoic acid (PABA), 4-(4-amino-phenyl)-butyric acid (PFB), 3-(4-amino-phenyl)-propionic acid (PFP). Thus, a GC/AA interface is produced featuring carboxylic groups facing the solution. Electrochemical (cyclic voltammetry and electrochemical impedance spectroscopy) and XPS techniques are used to experimentally characterize the grafting process and the surface state. The theoretical results are compared with the experimental evidence to determine, at a molecular level, the overall grafting mechanism. Ionization potentials, standard oxidation potentials, HOMO and electron spin distributions are calculated at the CCD/6-31G* level of the theory. The comparison of experimental and theoretical data suggests that the main electroactive species is the “zwitterionic” form for the three aliphatic amino acids, while the amino acids featuring the amino group bound to the phenyl aromatic moiety show a different behaviour. The comparison between experimental and theoretical results suggests that both the neutral and the zwitterionic forms are present in the acetonitrile solution in the case of 4-(4-amino-phenyl)-butyric acid (PFB) and 3-(4-amino-phenyl)-propionic acid.

Step-height standards based on the rapid formation of monolayer steps on the surface of layered crystals

Energy Technology Data Exchange (ETDEWEB)

Komonov, A.I. [Rzhanov Institute of Semiconductor Physics, Siberian Branch of the Russian Academy of Sciences (ISP SBRAS), pr. Lavrentieva 13, Novosibirsk 630090 (Russian Federation); Prinz, V.Ya., E-mail: prinz@isp.nsc.ru [Rzhanov Institute of Semiconductor Physics, Siberian Branch of the Russian Academy of Sciences (ISP SBRAS), pr. Lavrentieva 13, Novosibirsk 630090 (Russian Federation); Seleznev, V.A. [Rzhanov Institute of Semiconductor Physics, Siberian Branch of the Russian Academy of Sciences (ISP SBRAS), pr. Lavrentieva 13, Novosibirsk 630090 (Russian Federation); Kokh, K.A. [Sobolev Institute of Geology and Mineralogy, Siberian Branch of the Russian Academy of Sciences (IGM SB RAS), pr. Koptyuga 3, Novosibirsk 630090 (Russian Federation); Shlegel, V.N. [Nikolaev Institute of Inorganic Chemistry, Siberian Branch of the Russian Academy of Sciences (NIIC SB RAS), pr. Lavrentieva 3, Novosibirsk 630090 (Russian Federation)

2017-07-15

Highlights: • Easily reproducible step-height standard for SPM calibrations was proposed. • Step-height standard is monolayer steps on the surface of layered single crystal. • Long-term change in surface morphology of Bi{sub 2}Se{sub 3} and ZnWO{sub 4} was investigated. • Conducting surface of Bi{sub 2}Se{sub 3} crystals appropriate for calibrating STM. • Ability of robust SPM calibrations under ambient conditions were demonstrated. - Abstract: Metrology is essential for nanotechnology, especially for structures and devices with feature sizes going down to nm. Scanning probe microscopes (SPMs) permits measurement of nanometer- and subnanometer-scale objects. Accuracy of size measurements performed using SPMs is largely defined by the accuracy of used calibration measures. In the present publication, we demonstrate that height standards of monolayer step (∼1 and ∼0.6 nm) can be easily prepared by cleaving Bi{sub 2}Se{sub 3} and ZnWO{sub 4} layered single crystals. It was shown that the conducting surface of Bi{sub 2}Se{sub 3} crystals offers height standard appropriate for calibrating STMs and for testing conductive SPM probes. Our AFM study of the morphology of freshly cleaved (0001) Bi{sub 2}Se{sub 3} surfaces proved that such surfaces remained atomically smooth during a period of at least half a year. The (010) surfaces of ZnWO{sub 4} crystals remained atomically smooth during one day, but already two days later an additional nanorelief of amplitude ∼0.3 nm appeared on those surfaces. This relief, however, did not further grow in height, and it did not hamper the calibration. Simplicity and the possibility of rapid fabrication of the step-height standards, as well as their high stability, make these standards available for a great, permanently growing number of users involved in 3D printing activities.

Active vibration control of a cylindrical structure using flexible piezoactuators: experimental work in air and water environments

International Nuclear Information System (INIS)

Sohn, Jung Woo; Choi, Seung-Bok

2014-01-01

In the present work, the modal characteristics and vibration control performance of a cylindrical structure in air and water are experimentally investigated, and the results are presented in time and frequency domains. In order to achieve this goal, an end-capped cylindrical shell structure is considered as a host structure, and MFC (macro fiber composite) actuators, which are flexible, are bonded on the surface of the structure. After manufacturing a cylindrical shell structure with aluminum, a modal test is carried out, and the natural frequencies of the proposed structure are obtained and analyzed. To verify the modal test results, a finite element analysis is also performed, and the results are compared with the modal test results. By using the experimentally obtained modal characteristics, a state space control model is established. An optimal controller is then designed in order to control the unwanted vibration and is experimentally realized. It has been shown that the structural vibration can be effectively decreased with the optimal control methodology in both air and water environmental conditions. (technical note)

The VHCF experimental investigation of FV520B-I with surface roughness Ry

Science.gov (United States)

Wang, J. L.; Zhang, Y. L.; Ding, M. C.; Zhao, Q. C.

2018-05-01

Different surface roughness type (Ra and Ry) has different effect on the VHCF failure and life. Ra is widely employed as the quantitative expression of the surface roughness, but there are few fatigue failure mechanism analysis and experimental study under surface roughness Ry. The VHCF experiment is conducted out using the specimen with different surface roughness values. The surface roughness Ry is employed as the major research object to investigate the relationship and distribution tendency between the Ry, fatigue life and the distance between internal inclusion and surface, and a new VHCF failure character is proposed.

Effect of implantoplasty on fracture resistance and surface roughness of standard diameter dental implants.

Science.gov (United States)

Costa-Berenguer, Xavier; García-García, Marta; Sánchez-Torres, Alba; Sanz-Alonso, Mariano; Figueiredo, Rui; Valmaseda-Castellón, Eduard

2018-01-01

To assess the effect of implantoplasty on the fracture resistance, surface roughness, and macroscopic morphology of standard diameter (4.1 mm) external connection dental implants. An in vitro study was conducted in 20 screw-shaped titanium dental implants with an external connection. In 10 implants, the threads and surface were removed and polished with high-speed burs (implantoplasty), while the remaining 10 implants were used as controls. The final implant dimensions were recorded. The newly polished surface quality was assessed by scanning electron microscopy (SEM) and by 3D surface roughness analysis using a confocal laser microscope. Finally, all the implants were subjected to a mechanical pressure resistance test. A descriptive analysis of the data was made. Also, Student's t tests were employed to detect differences regarding the compression tests. Implantoplasty was carried out for a mean time of 10 min and 48 s (standard deviation (SD) of 1 min 22 s). Macroscopically, the resulting surface had a smooth appearance, although small titanium shavings and silicon debris were present. The final surface roughness (S a values 0.1 ± 0.02 μm) was significantly lower than that of the original (0.75 ± 0.08 μm S a ) (p = .005). There was minimal reduction in the implant's inner body diameter (0.19 ± 0.03 mm), and no statistically significant differences were found between the test and control implants regarding the maximum resistance force (896 vs 880 N, respectively). Implantoplasty, although technically demanding and time-consuming, does not seem to significantly alter fracture resistance of standard diameter external connection implants. A smooth surface with S a values below 0.1 μm can be obtained through the use of silicon polishers. A larger sample is required to confirm that implantoplasty does not significantly affect the maximum resistance force of standard diameter external connection implants. © 2017 John Wiley & Sons A/S. Published

Experimental and numerical study on free surface behavior of windowless target

International Nuclear Information System (INIS)

Su Guanyu; Gu Hanyang; Cheng Xu

2012-01-01

The formation and control method of coolant free surface is one of the key technologies for the design of windowless target in accelerator driven sub-critical system (ADS). Experimental and CFD investigations on free surface behavior were performed in a scaled windowless target model by using water as test fluid. Laser induced fluorescence was applied for flow field visualization. The free surface and flow field visualization were obtained at Re=30000-50000. Under high Re conditions, an unsteady vortex pair was obtained. By decreasing Re, the structure of the vortex becomes more turbulent. CFD simulation was performed using LES and kω-SST turbulence models, separately. The numerical results show that LES model can qualitatively reproduce the characteristics of flow field and free surface. (authors)

Comparative evaluations of surface contamination detectors calibration with radioactive sources - used in the Goiania accident, and standard sources

International Nuclear Information System (INIS)

Becker, P.H.B.; Marecha, M.H.H.

1997-01-01

The construction of Cs-137 standard flat sources for calibration of surface contamination detectors, used in the Goiania accident in 1987, is described and the procedures adopted are reported. At that time, standard sources were not available. Nowadays the Instituto de Radioprotecao e Dosimetria has standard sources acquired from Amersham which are used as calibration standards for surface contamination detectors. Comparative evaluations between the standard flat sources constructed for the accident and the calibrated ones are presented

77 FR 19008 - Guidelines for Home Energy Professionals: Standard Work Specifications for Single Family Energy...

Science.gov (United States)

2012-03-29

.... The development of the Guidelines for Home Energy Professionals: Standard Work Specifications for... DEPARTMENT OF ENERGY Office of Energy Efficiency and Renewable Energy Guidelines for Home Energy Professionals: Standard Work Specifications for Single Family Energy Upgrades AGENCY: Office of Energy...

77 FR 23238 - Guidelines for Home Energy Professionals: Standard Work Specifications for Single Family Energy...

Science.gov (United States)

2012-04-18

...: Comments on the Guidelines for Home Energy Professionals: Standard Work Specifications for Single Family... DEPARTMENT OF ENERGY Office of Energy Efficiency and Renewable Energy Guidelines for Home Energy Professionals: Standard Work Specifications for Single Family Energy Upgrades AGENCY: Office of Energy...

Standardization of the Experimental Methodology for Quality Assurance and Quality Control (QA-QC of the CLIC Structural Materials

Directory of Open Access Journals (Sweden)

N. Gazis

2015-04-01

Full Text Available The main linear accelerators (linacs of the Compact LInear Collider (CLIC are constituted of sequential two-beam modules (of approximate length of two meters. The CLIC linacs need to be firmly stabilized on their supports with a micron-level requirement, essential for maintaining the final target luminosity close to the required XXX value. Real scale two-beam prototype modules have been designed, manufactured and commissioned to study their behaviour under different operation modes and experimental conditions. The CLIC machine will work for continuous runs under conditions of high radiation background. The structural materials of the systems of the accelerator have to sustain the significant fatigue and activation due to the radiation, generated mainly by the losses of the particle beam. Extensive testing has taken place with a combination of mechanical experiments and irradiation sessions on samples of structural materials, focusing on the micro-precise CLIC module supporting system. The followed experimentally strategy was standardized in a series of sequential steps.

Systematic review: work-related stress and the HSE management standards.

Science.gov (United States)

Brookes, K; Limbert, C; Deacy, C; O'Reilly, A; Scott, S; Thirlaway, K

2013-10-01

The Health and Safety Executive (HSE) has defined six management standards representing aspects of work that, if poorly managed, are associated with lower levels of employee health and productivity, and increased sickness absence. The HSE indicator tool aims to measure organizations' performance in managing the primary stressors identified by the HSE management standards. The aims of the study are to explore how the HSE indicator tool has been implemented within organizations and to identify contexts in which the tool has been used, its psychometric properties and relationships with alternative measures of well-being and stress. Studies that matched specific criteria were included in the review. Abstracts were considered by two researchers to ensure a reliable process. Full texts were obtained when abstracts met the inclusion criteria. Thirteen papers were included in the review. Using factor analysis and measures of reliability, the studies suggest that the HSE indicator tool is a psychometrically sound measure. The tool has been used to measure work-related stress across different occupational groups, with a clear relationship between the HSE tool and alternative measures of well-being. Limitations of the tool and recommendations for future research are discussed. The HSE indicator tool is a psychometrically sound measure of organizational performance against the HSE management standards. As such it can provide a broad overview of sources of work-related stress within organizations. More research is required to explore the use of the tool in the design of interventions to reduce stress, and its use in different contexts and with different cultural and gender groups.

Experimental validation of a new heterogeneous mechanical test design

Science.gov (United States)

Aquino, J.; Campos, A. Andrade; Souto, N.; Thuillier, S.

2018-05-01

Standard material parameters identification strategies generally use an extensive number of classical tests for collecting the required experimental data. However, a great effort has been made recently by the scientific and industrial communities to support this experimental database on heterogeneous tests. These tests can provide richer information on the material behavior allowing the identification of a more complete set of material parameters. This is a result of the recent development of full-field measurements techniques, like digital image correlation (DIC), that can capture the heterogeneous deformation fields on the specimen surface during the test. Recently, new specimen geometries were designed to enhance the richness of the strain field and capture supplementary strain states. The butterfly specimen is an example of these new geometries, designed through a numerical optimization procedure where an indicator capable of evaluating the heterogeneity and the richness of strain information. However, no experimental validation was yet performed. The aim of this work is to experimentally validate the heterogeneous butterfly mechanical test in the parameter identification framework. For this aim, DIC technique and a Finite Element Model Up-date inverse strategy are used together for the parameter identification of a DC04 steel, as well as the calculation of the indicator. The experimental tests are carried out in a universal testing machine with the ARAMIS measuring system to provide the strain states on the specimen surface. The identification strategy is accomplished with the data obtained from the experimental tests and the results are compared to a reference numerical solution.

30 CFR 785.13 - Experimental practices mining.

Science.gov (United States)

2010-07-01

... practices granting variances from the special environmental protection performance standards of sections 515... INTERIOR SURFACE COAL MINING AND RECLAMATION OPERATIONS PERMITS AND COAL EXPLORATION SYSTEMS UNDER REGULATORY PROGRAMS REQUIREMENTS FOR PERMITS FOR SPECIAL CATEGORIES OF MINING § 785.13 Experimental practices...

Experimental and calculational works on characteristics of the Dalat Nuclear Research Reactor. Second edition

International Nuclear Information System (INIS)

Pham Ngoc Khoi; Nguyen Kim Dung

2016-03-01

Recognizing the significant value and necessity of publishing the scientific document of experimental and calculational works on the Dalat Nuclear Research Reactor (DNRR) physics and engineering for research, operation, training activities as well as for international scientific exchange, Vietnam Atomic Energy Agency (VAEA) and Vietnam Atomic Energy Institute have completed editing to publish the “Experimental and Calculational Works on Characteristics of THE DALAT NUCLEAR RESEARCH REACTOR” which consists of 26 typical papers representing the most important experimental and calculational results of the DNRR physics and engineering obtained during 30 years of operation and exploitation with the contribution of Vietnamese and former USSR’s experts, especially scientists and engineers working at the Reactor Center of the NRI

Uses of ANSI/HPS N13.12-1999, "Surface and Volume Radioactivity Standards for Clearance" and Comparison with Existing Standards

Energy Technology Data Exchange (ETDEWEB)

Stansbury, Paul S.; Strom, Daniel J.

2001-04-30

In August of 1999, the American National Standards Institute (ANSI) approved a standard for clearance of materials contaminated with residual levels of radioactivity. "Clearance," as used in the standard, means the movement of material from the control of a regulatory agency to a use or disposition that has no further regulatory controls of any kind. The standard gives derived screening levels (DSLs) in Bq/g and Bq/cm2 for 50 radionuclides. Items or materials with residual surface and volume radioactivity levels below the DSLs can be cleared, that is, managed without regard to their residual radioactivity. Since federal agencies are to use voluntary, industry standards developed by the private sector whenever possible, the standard should play an important role in DOE's regulatory process. The thrust of this report is to explain the standard, make simple observations on its usefulness to DOE, and to explore uses of the standard within DOE facilities beyond the clearance of radioactive materials.

Experimental investigation of Surface Roughness and Cutting force in CNC Turning - A Review

Directory of Open Access Journals (Sweden)

Dhiraj Patel

2014-08-01

Full Text Available The main purpose of this review paper is to check whether quality lies within desired tolerance level which can be accepted by the customers. So, experimental investigation surface roughness and cutting force using various CNC machining parameters including spindle speed (N, feed rate (f, and depth of cut (d,flow rate (Q and insert nose radius (r. As such, a solemn attempt is made in this paper to investigate the response parameters, viz., Cutting force and Surface Roughness (Ra a by experimentation on EN 19 turning process. The Design of experiments is carried-out considering Taguchi Technique with four input parameters, namely, spindle speed, feed rate, and depth of cut, flow rate and insert nose radius .The experiments are conducted considering the above materials for L16 and then the impact of each parameter is estimated by ANOAVA. Then the regression analysis is carried-out to find the trend of the response of each material. This experimental study aims at taguchi method has been applied for finding the effect on surface roughness and cutting force by various process parameters. And after that we can easily find out that which parameter will be more affect.

An experimental method for making spectral emittance and surface temperature measurements of opaque surfaces

International Nuclear Information System (INIS)

Moore, Travis J.; Jones, Matthew R.; Tree, Dale R.; Daniel Maynes, R.; Baxter, Larry L.

2011-01-01

An experimental procedure has been developed to make spectral emittance and temperature measurements. The spectral emittance of an object is calculated using measurements of the spectral emissive power and of the surface temperature of the object obtained using a Fourier transform infrared (FTIR) spectrometer. A calibration procedure is described in detail which accounts for the temperature dependence of the detector. The methods used to extract the spectral emissive power and surface temperature from measured infrared spectra were validated using a blackbody radiator at known temperatures. The average error in the measured spectral emittance was 2.1% and the average difference between the temperature inferred from the recorded spectra and the temperature indicated on the blackbody radiator was 1.2%. The method was used to measure the spectral emittance of oxidized copper at various temperatures.

Randomization and Data-Analysis Items in Quality Standards for Single-Case Experimental Studies

Science.gov (United States)

Heyvaert, Mieke; Wendt, Oliver; Van den Noortgate, Wim; Onghena, Patrick

2015-01-01

Reporting standards and critical appraisal tools serve as beacons for researchers, reviewers, and research consumers. Parallel to existing guidelines for researchers to report and evaluate group-comparison studies, single-case experimental (SCE) researchers are in need of guidelines for reporting and evaluating SCE studies. A systematic search was…

Experimental study of lithium free-surface flow for IFMIF target design

International Nuclear Information System (INIS)

Kondo, H.; Fujisato, A.; Yamaoka, N.; Inoue, S.; Miyamoto, S.; Iida, T.; Nakamura, H.; Ida, M.; Matushita, I.; Muroga, T.; Horiike, H.

2006-01-01

Lithium free-surface flow experiments to verify the design of IFMIF target have been carried out at Osaka University. The present report summarizes experimental results of surface phenomena, and cavitation characteristics of the loop, so as to try to apply these results to design parameters. Waves on the lithium flow surface is similar to that on water, and can be predicted by a linear stability theory. The wave amplitude is measured by an electro-contact probe. Surface roughness on a target nozzle, caused for example by attached chemical compounds and/or wastages by erosion and corrosion, can lead to a significant loss of target flow stability as well as surface wakes. The need of a polishing manipulator or exchange of the nozzle may be anticipated. Cavitation characteristic of the loop was measured by an accelerometer. From the results, a friction factor could be estimated fort he lithium flow

Work-related symptoms and checkstand configuration: an experimental study.

Science.gov (United States)

Harber, P; Bloswick, D; Luo, J; Beck, J; Greer, D; Peña, L F

1993-07-01

Supermarket checkers are known to be at risk of upper-extremity cumulative trauma disorders. Forty-two experienced checkers checked a standard "market basket" of items on an experimental checkstand. The counter height could be adjusted (high = 35.5, low = 31.5 inches), and the pre-scan queuing area length (between conveyor belt and laser scanner) could be set to "near" or "far" lengths. Each subject scanned under the high-near, high-far, low-near, and low-far conditions in random order. Seven ordinal symptom scales were used to describe comfort. Analysis showed that both counter height and queuing length had significant effects on symptoms. Furthermore, the height of the subject affected the degree and direction of the impact of the checkstand configuration differences. The study suggests that optimization of design may be experimentally evaluated, that modification of postural as well as frequency loading may be beneficial, and that adjustability for the individual may be advisable.

Experimental study of surface plasmon-phonon polaritons in GaAs-based microstructures

Science.gov (United States)

Galimov, A. I.; Shalygin, V. A.; Moldavskaya, M. D.; Panevin, V. Yu; Melentyev, G. A.; Artemyev, A. A.; Firsov, D. A.; Vorobjev, L. E.; Klimko, G. V.; Usikova, A. A.; Komissarova, T. A.; Sedova, I. V.; Ivanov, S. V.

2018-03-01

Optical properties of a heavily-doped GaAs epitaxial layer with a regular grating at its surface have been experimentally investigated in the terahertz spectral range. Reflectivity spectra for the layer with a profiled surface drastically differ from those for the as-grown epilayer with a planar surface. For s-polarized radiation, this difference is totally caused by the electromagnetic wave diffraction at the grating. For p-polarized radiation, additional resonant dips arise due to excitation of surface plasmon-phonon polaritons. Terahertz radiation emission under significant electron heating in an applied pulsed electric field has also been studied. Polarization measurements revealed pronounced peaks related to surface plasmon-phonon polariton resonances of the first and second order in the emission spectra.

AACN's healthy work environment standards and an empowering nurse advancement system.

Science.gov (United States)

Vollers, Dawn; Hill, Edie; Roberts, Cynthia; Dambaugh, Lori; Brenner, Zara R

2009-12-01

An empowering clinical nurse advancement system can facilitate institutional behaviors that embrace all of AACN's healthy work environment standards and thus serve as a building block for developing a flourishing health care environment. The results generate positive outcomes that are evident to health care professionals, patients, patients' families, and health care organizations. Patients benefit from highly satisfied employees who work in a culture of caring and excellence.

Experimental and numerical analysis of microstructured surfaces

OpenAIRE

Diani, Andrea

2014-01-01

Heat dissipation is one of the most important issues for the reliability of electronics equipment. Up today, air represents the most safe, cheap, and common working fluid for electronics thermal management applications. Due to its poor heat transfer characteristics, air always flow through enhanced surfaces, such as plain and louvered fins, pin fins, offset strip fins and wire screens, in order to increase the heat transfer area and to create turbulence. Recently, metal foams have been propos...

[The standard of position of physician-stomatologist-therapeutist in the conditions of working together with assistant-stomatological].

Science.gov (United States)

Kalininskaya, A A; Mescheryakov, D G; Ildarov, R B

2013-01-01

The article presents scope of work, algorithms of labor operations, standardization of work of stomatologist-therapeutist in the conditions of working together with assistant-stomatological in four hands. The calculations are given concerning the standard numbers of positions of stomatologist in new conditions of work.

Quantum Hall resistance standard in graphene devices under relaxed experimental conditions

Science.gov (United States)

Schopfer, F.; Ribeiro-Palau, R.; Lafont, F.; Brun-Picard, J.; Kazazis, D.; Michon, A.; Cheynis, F.; Couturaud, O.; Consejo, C.; Jouault, B.; Poirier, W.

Large-area and high-quality graphene devices synthesized by CVD on SiC are used to develop reliable electrical resistance standards, based on the quantum Hall effect (QHE), with state-of-the-art accuracy of 1x10-9 and under an extended range of experimental conditions of magnetic field (down to 3.5 T), temperature (up to 10 K) or current (up to 0.5 mA). These conditions are much relaxed as compared to what is required by GaAs/AlGaAs standards and will enable to broaden the use of the primary quantum electrical standards to the benefit of Science and Industry for electrical measurements. Furthermore, by comparison of these graphene devices with GaAs/AlGaAs standards, we demonstrate the universality of the QHE within an ultimate uncertainty of 8.2x10-11. This suggests the exact relation of the quantized Hall resistance with the Planck constant and the electron charge, which is crucial for the new SI to be based on fixing such fundamental constants. These results show that graphene realizes its promises and demonstrates its superiority over other materials for a demanding application. Nature Nanotech. 10, 965-971, 2015, Nature Commun. 6, 6806, 2015

Standard test method for determination of surface lubrication on flexible webs

CERN Document Server

American Society for Testing and Materials. Philadelphia

1999-01-01

1.1 This test method has been used since 1988 as an ANSI/ISO standard test for determination of lubrication on processed photographic films. Its purpose was to determine the presence of process-surviving lubricants on photographic films. It is the purpose of this test method to expand the applicability of this test method to other flexible webs that may need lubrication for suitable performance. This test measures the breakaway (static) coefficient of friction of a metal rider on the web by the inclined plane method. The objectives of the test is to determine if a web surface has a lubricant present or not. It is not intended to assign a friction coefficient to a material. It is not intended to rank lubricants. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish ...

Experimental study on working characteristics of density lock

International Nuclear Information System (INIS)

Sun Furong; Yan Changqi; Gu Haifeng

2011-01-01

The working principle of density lock was introduced in this paper, and the experimental loop was built so that researches on working performance of density lock in the system were done at steady-state operation and pump trip conditions. The results show that at steady-state operation conditions, density lock can keep close in a long run, which will separate passive residual heat removal circuit from primary circuit. As a result, passive residual heat removal circuit is in the non-operating conditions, which dose not influence normal operation of reactors. At the pump trip conditions, density lock can be automatically opened quickly, which will make primary and passive residual heat removal system communicated. The natural circulation is well established in the two systems, and is enough to ensure removal of residual heat. (authors)

Current status of restoration work for obstacle and upper core structure in reactor vessel of experimental fast reactor 'Joyo'. 1. MARICO-2 subassembly retrieval work

International Nuclear Information System (INIS)

Naito, Hiroyuki; Ashida, Takashi; Ito, Hideaki

2014-01-01

At Joyo reactor MK-III core in May 2007, due to the design deficiencies of the disconnect mechanism of the holding part and the sample part of the experimental apparatus with instrumentation lines (MARICO-2), a disconnect failure incident occurred in the sample part after irradiation test. The deformation of the sample part due to this failure incurred its interference with the lower surface of reactor core upper structure and the holddown axis body. By this, the operating range of the rotary plug was restricted, leading to the partial inhibition of the fuel exchange function that precluded the access to 1/4 of the assemblies of the reactor core. In face of restoration work, the preparation for restoration such the exchange of upper core structure, and the recovery of MARICO-2 sample part are under way. This paper introduces the progress of restoration work and the future work plan, with a focus on the outline of overall restoration work, the method / problems / measures for MARICO-2 sample part recovery operations, and fabrication of sample part recovery device. (A.O.)

A theoretical and experimental investigation of the interaction between gas molecules and cryogenic surfaces

International Nuclear Information System (INIS)

Varlam, M.; Steflea, D.; Chiriloaie, N.

1992-01-01

The cryo-pumping performance of a cryo-surface subjected to the impingement of low-pressure, thermal-velocity air flow is experimentally and theoretically investigated. Our purpose is to determine the angular dependence of capture coefficients for gas molecules incident on a cryogenic surface under conditions closely approximating those prevailing in cryo-pumped high vacuum chambers. The classical model for the interaction of gas atoms and the solid surface - the 'soft-tube' model - is developed and the basic assumption are examined. Starting from this theory we have calculated the capture coefficient of the Ag - N system and these values are discussed in terms of principal parameters considered. Despite the many simplifying assumptions, this model has the important attribute that it yields closed-form expressions for the capture coefficient of gas molecules. The molecular beam technique offers a direct experimental method for determining the capture coefficient for molecules with given angles of incidence by measuring the incident and reflected molecular fluxes. An experimental setup is also designed and the method for determining these coefficients is proposed. (Author)

Effects of vacuum heat treatment on the photoelectric work function and surface morphology of multilayered silver–metal electrical contacts

International Nuclear Information System (INIS)

Akbi, Mohamed; Bouchou, Aïssa; Zouache, Noureddine

2014-01-01

Contact materials used for electrical breakers are often made with silver alloys. Mechanical and thermodynamical properties as well as electron emission of such complicated alloys present a lack of reliable and accurate experimental data. This paper deals mainly with electron work function (EWF) measurements about silver–metal (Ag–Me) electrical contacts (Ag–Ni (60/40) and Ag–W (50/50)), before and after surface heat treatments at 513 K–873 K, under UHV conditions (residual gas pressure of 1.4 × 10 −7 mbar). The electron work function (EWF) of silver alloyed contacts was measured photoelectrically, using both Fowler's method of isothermal curves and linearized Fowler plots. An interesting fact brought to light by this investigation is that after vacuum heat treatments, the diffusion and/or evaporation phenomena, affecting the atomic composition of the alloy surface, somehow confine the EWF of the silver–nickel alloy, Φ(Ag–Ni), determined at room temperature in interval]Φ(Ag), Φ(Ni) [=] 4.26 eV, 4.51 eV[. Surface analysis of two specimens before and after heating showed a significant increase of tungsten atomic proportion on the contact surface for Ag–W contacts after VH treatments. A multilayer model, taking into account the strong intergranular and volume segregation gives a good interpretation of the obtained results.

Experimental investigation of pool boiling heat transfer and critical heat flux on a downward facing surface

International Nuclear Information System (INIS)

Gocmanac, M.; Luxat, J.C.

2012-01-01

A separate effects experimental study of heat transfer and Critical Heat Flux (CHF) on a downward facing plate in subcooled water pool boiling is described. Two geometries of downwards facing surfaces are studied. The first is termed the 'confined' study in which bubble motion is restricted to the heated surface. The second is termed the 'unconfined' study where individual bubbles are free to move along the heated surface and vent in any direction. The method used in the confined study is novel and involves the placement of a lip surrounding the heated surface. The CHF as a function of angle of inclination of the surface is presented and is in good agreement with other experimental data from somewhat different test geometries. (author)

Modification of silicon nitride surfaces with GOPES and APTES for antibody immobilization: computational and experimental studies

International Nuclear Information System (INIS)

To, Thien Dien; Nguyen, Anh Tuan; Phan, Khoa Nhat Thanh; Truong, An Thu Thi; Doan, Tin Chanh Duc; Dang, Chien Mau

2015-01-01

Chemical modification of silicon nitride (SiN) surfaces by silanization has been widely studied especially with 3-(aminopropyl)triethoxysilane (APTES) and 3-(glycidyloxypropyl) dimethylethoxysilane (GOPES). However few reports performed the experimental and computational studies together. In this study, surface modification of SiN surfaces with GOPES and APTES covalently bound with glutaraldehyde (GTA) was investigated for antibody immobilization. The monoclonal anti-cytokeratin-FITC (MACF) antibody was immobilized on the modified SiN surfaces. The modified surfaces were characterized by water contact angle measurements, atomic force microscopy and fluorescence microscopy. The FITC-fluorescent label indicated the existence of MACF antibody on the SiN surfaces and the efficiency of the silanization reaction. Absorption of APTES and GOPES on the oxidized SiN surfaces was computationally modeled and calculated by Materials Studio software. The computational and experimental results showed that modification of the SiN surfaces with APTES and GTA was more effective than the modification with GOPES. (paper)

Hard Work in Soft Regulation: A Discussion of the Social Mechanisms in OHS Management Standards and Possible Dilemmas in the Regulation of Psychosocial Work Environment

Directory of Open Access Journals (Sweden)

Pernille Hohnen

2014-09-01

Full Text Available Certified occupational health and safety (OHS management systems have become a global instrument in regulation of the work environment. However, their actual impact on OHS—in particular on softer psychosocial issues in the work environment—has been questioned. The most important standard of OHS management is OHSAS 18001, which has recently been supplemented with a British publically available guideline (PAS 1010 focusing specifically on psychosocial risk management. On the basis of the international literature on management standards, the present paper analyses OHSAS 18001 and PAS 1010 in order to understand the mechanism by which they work. The paper takes a social constructionist approach conceptualizing standards and their expected mechanisms as socially constructed—based on a particular kind of knowledge and logic—although they are presented as objective. Such a constructionist approach also emphasizes how standards transform specific work environment problems into generic procedures that can be audited. In the case of OHS standards, both the work environment in general and the psychosocial risks in particular are transformed into simple monocausal auditable relations whereby the complexity of psychosocial work environment issues seems to disappear. The new PAS 1010 guideline, which is particularly focusing on regulation of the psychosocial work environment, only partly succeeds in solving these shortcomings of OHSAS 18001.

Experimental study of surface quality and damage when drilling unidirectional CFRP composites

Directory of Open Access Journals (Sweden)

Eshetu D. Eneyew

2014-10-01

Full Text Available In this study, an experimental investigation on the drilling of unidirectional carbon fiber reinforced plastic (UD-CFRP composite was conducted using polycrystalline diamond (PCD tipped eight facet drill. The quality of the drilled hole surface was examined through surface roughness measurements and surface damage by scanning electron microscopy (SEM. It was found that fiber pullout occurred in two specific sectors relative to the angle between the cutting direction and the fiber orientation. The thrust force was highly influenced by the feed rate than the cutting speed and it shows a significant variation throughout the rotation of the drill.

Experimental and Theoretical Investigations of Glass Surface Charging Phenomena

Science.gov (United States)

Agnello, Gabriel

Charging behavior of multi-component display-type (i.e. low alkali) glass surfaces has been studied using a combination of experimental and theoretical methods. Data obtained by way of a Rolling Sphere Test (RST), streaming/zeta potential and surface energy measurements from commercially available display glass surfaces (Corning EAGLE XGRTM and Lotus(TM) XT) suggest that charge accumulation is highly dependent on surface treatment (chemical and/or physical modification) and measurement environment, presumably through reactionary mechanisms at the surface with atmospheric moisture. It has been hypothesized that water dissociation, along with the corresponding hydroxylation of the glass surface, are important processes related to charging in glass-metal contact systems. Classical Molecular Dynamics (MD) simulations, in conjunction with various laboratory based measurements (RST, a newly developed ElectroStatic Gauge (ESG) and Diffuse Reflectance Infrared Fourier Transform Spectroscopy (DRIFTS)) on simpler Calcium AluminoSilicate (CAS) glass surfaces were used to further explore these phenomena. Analysis of simulated high-silica content (≥50%) (CAS) glass structures suggest that controlled variation of bulk chemistry can directly affect surface defect concentrations, such as non-bridging oxygen (NBO), which can be suitable high-energy sites for hydrolysis-type reactions to occur. Calculated NBO surface concentrations correlate well with charge based measurements on laboratory fabricated CAS surfaces. The data suggest that a directional/polar shift in contact-charge transfer occurs at low silica content (≤50%) where the highest concentrations of NBOs are observed. Surface charging sensitivity with respect to NBO concentration decreases as the relative humidity of the measurement environment increases; which should be expected as the highly reactive sites are progressively covered by liquid water layers. DRIFTS analysis of CAS powders expand on this analysis showing

40 CFR 63.5755 - How do I demonstrate compliance with the aluminum recreational boat surface coating spray gun...

Science.gov (United States)

2010-07-01

... the aluminum recreational boat surface coating spray gun cleaning work practice standards? 63.5755... surface coating spray gun cleaning work practice standards? You must demonstrate compliance with the aluminum coating spray gun cleaning work practice standards by meeting the requirements of paragraph (a) or...

Experimental verification for standard analysis procedure of 241Am in food

International Nuclear Information System (INIS)

Liu Qingfen; Zhu Hongda; Liu Shutian; Pan Jingshun; Yang Dating

2005-01-01

Objective: The briefly experimental verification for 'determination of 241 Am in food' has been described. Methods: The overall recovery, the MDL of method and decontamination experiment has been done by standard analysis procedure. Results: The overall recovery is 76.26 ± 4.1%. The MDL is 3.4 x 10 -5 Bq/g ash, decontamination factor is higher than 10 3 for Po, 10 2 for U, Th, Pu and 60 for 237 Np. Conclusion: The results showed that the overall recovery is quite high and reliable, the MDL of method is able to meet examining 241 Am limited values in foods. the obtained decontamination factors of recommended procedure can meet analysis of 241 Am in food examination. Venifying results of the procedure are satisfied by using 243 Am spike and 241 Am standard reference material. (authors)

The multi-component model of working memory: explorations in experimental cognitive psychology.

Science.gov (United States)

Repovs, G; Baddeley, A

2006-04-28

There are a number of ways one can hope to describe and explain cognitive abilities, each of them contributing a unique and valuable perspective. Cognitive psychology tries to develop and test functional accounts of cognitive systems that explain the capacities and properties of cognitive abilities as revealed by empirical data gathered by a range of behavioral experimental paradigms. Much of the research in the cognitive psychology of working memory has been strongly influenced by the multi-component model of working memory [Baddeley AD, Hitch GJ (1974) Working memory. In: Recent advances in learning and motivation, Vol. 8 (Bower GA, ed), pp 47-90. New York: Academic Press; Baddeley AD (1986) Working memory. Oxford, UK: Clarendon Press; Baddeley A. Working memory: Thought and action. Oxford: Oxford University Press, in press]. By expanding the notion of a passive short-term memory to an active system that provides the basis for complex cognitive abilities, the model has opened up numerous questions and new lines of research. In this paper we present the current revision of the multi-component model that encompasses a central executive, two unimodal storage systems: a phonological loop and a visuospatial sketchpad, and a further component, a multimodal store capable of integrating information into unitary episodic representations, termed episodic buffer. We review recent empirical data within experimental cognitive psychology that has shaped the development of the multicomponent model and the understanding of the capacities and properties of working memory. Research based largely on dual-task experimental designs and on neuropsychological evidence has yielded valuable information about the fractionation of working memory into independent stores and processes, the nature of representations in individual stores, the mechanisms of their maintenance and manipulation, the way the components of working memory relate to each other, and the role they play in other

Standardization activities of the Euratom Neutron Radiography Working Group

International Nuclear Information System (INIS)

Domanus, J.

1982-06-01

In 1979 a working group on neutron radiography was formed at Euratom. The purpose of this group is the standardization of neutron radiographic methods in the field of nuclear fuel. Activities of this Neutron Radiography Working Group are revised. Classification of defects revealed by neutron radiography is illustrated in a special atlas. Beam purity and sensitivity indicators are tested together with a special calibration fuel pin. All the Euratom neutron radiography centers will perform comparative neutron radiography with those items. The measuring results obtained, using various measuring aparatus will form the basis to formulate conclusions about the best measuring methods and instruments to be used in that field. Besides the atlas of neutron radiographic findings in light water reactor fuel, the Euratom Neutron Radiogrphy Working Group has published a neutron radiography handbook in which the neutron radiography installations in the European Community are also described. (author)

Experimental study of liquid drop impact onto a powder surface

KAUST Repository

Marston, Jeremy; Thoroddsen, Sigurdur T; Ng, Waikiong; Tan, Reginald

2010-01-01

The initial dynamics of liquid drop impact onto powder surfaces is studied experimentally using high-speed photography. For a range of bed packing fractions, φ, liquid physical properties and impact velocities, ui, we observe a variety of phenomena that can be representative of a hydrophobic surface, a rough surface or a porous medium. The solids packing fraction in the bed, 0.38≤φ≤0.65, and the impact Weber number, 3.5≤We=ρDui 2/φ≤750, (where ρ, D and φ are the drop density, diameter and surface tension respectively) are shown to be the critical parameters governing the outcome of an impact. For high packing fractions, φ≳0.5, we show that the observed spreading, rebound and splashing can be broadly characterised in terms of the Weber number while for looser packing fractions, φ≲0.5, we observe powder ejectas and provide a qualitative description of the granule nucleation at the centre of the impact sites. © 2010 Elsevier B.V.

Experimental study of liquid drop impact onto a powder surface

KAUST Repository

Marston, Jeremy

2010-11-01

The initial dynamics of liquid drop impact onto powder surfaces is studied experimentally using high-speed photography. For a range of bed packing fractions, φ, liquid physical properties and impact velocities, ui, we observe a variety of phenomena that can be representative of a hydrophobic surface, a rough surface or a porous medium. The solids packing fraction in the bed, 0.38≤φ≤0.65, and the impact Weber number, 3.5≤We=ρDui 2/φ≤750, (where ρ, D and φ are the drop density, diameter and surface tension respectively) are shown to be the critical parameters governing the outcome of an impact. For high packing fractions, φ≳0.5, we show that the observed spreading, rebound and splashing can be broadly characterised in terms of the Weber number while for looser packing fractions, φ≲0.5, we observe powder ejectas and provide a qualitative description of the granule nucleation at the centre of the impact sites. © 2010 Elsevier B.V.

Surface Traps in Colloidal Quantum Dots: A Combined Experimental and Theoretical Perspective.

Science.gov (United States)

Giansante, Carlo; Infante, Ivan

2017-10-19

Surface traps are ubiquitous to nanoscopic semiconductor materials. Understanding their atomistic origin and manipulating them chemically have capital importance to design defect-free colloidal quantum dots and make a leap forward in the development of efficient optoelectronic devices. Recent advances in computing power established computational chemistry as a powerful tool to describe accurately complex chemical species and nowadays it became conceivable to model colloidal quantum dots with realistic sizes and shapes. In this Perspective, we combine the knowledge gathered in recent experimental findings with the computation of quantum dot electronic structures. We analyze three different systems: namely, CdSe, PbS, and CsPbI 3 as benchmark semiconductor nanocrystals showing how different types of trap states can form at their surface. In addition, we suggest experimental healing of such traps according to their chemical origin and nanocrystal composition.

Standard molar enthalpy of formation of 1-benzosuberone: An experimental and computational study

International Nuclear Information System (INIS)

Miranda, Margarida S.; Morais, Victor M.F.; Matos, M. Agostinha R.; Liebman, Joel F.

2010-01-01

The energetics of 1-benzosuberone was studied by a combination of calorimetric techniques and computational calculations. The standard (p o = 0.1 MPa) molar enthalpy of formation of 1-benzosuberone, in the liquid phase, was derived from the massic energy of combustion, in oxygen, at T = 298.15 K, measured by static bomb combustion calorimetry. The standard molar enthalpy of vaporization, at T = 298.15 K, was measured by Calvet microcalorimetry. From these two parameters the standard (p o = 0.1 MPa) molar enthalpy of formation, in the gaseous phase, at T = 298.15 K, was derived: -(96.1 ± 3.4) kJ . mol -1 . The G3(MP2)//B3LYP composite method and appropriate reactions were used to computationally calculate the standard molar enthalpy of formation of 1-benzosuberone, in the gaseous phase, at T = 298.15 K. The computational results are in very good agreement with the experimental value.

Direct Experimental Evidence of Back-Surface Acceleration from Laser-Irradiated Foils

International Nuclear Information System (INIS)

Allen, M; Patel, P; Mackinnon, A; Price, D; Wilks, S; Morse, E

2004-01-01

Au foils were irradiated with a 100-TW, 100-fs laser at intensities greater than 10 20 W/cm 2 producing proton beams with a total yield of ∼ 10 11 and maximum proton energy of > 9 MeV. Removing contamination from the back surface of Au foils with an Ar-ion sputter gun reduced the total yield of accelerated protons to less than 1% of the yield observed without removing contamination. Removing contamination the front surface (laser-interaction side) of the target had no observable effect on the proton beam. We present a one-dimensional particle-in-cell simulation that models the experiment. Both experimental and simulation results are consistent with the back-surface acceleration mechanism described in the text

Les Houches 2015: Physics at TeV Colliders Standard Model Working Group Report

Energy Technology Data Exchange (ETDEWEB)

Andersen, J.R.; et al.

2016-05-16

This Report summarizes the proceedings of the 2015 Les Houches workshop on Physics at TeV Colliders. Session 1 dealt with (I) new developments relevant for high precision Standard Model calculations, (II) the new PDF4LHC parton distributions, (III) issues in the theoretical description of the production of Standard Model Higgs bosons and how to relate experimental measurements, (IV) a host of phenomenological studies essential for comparing LHC data from Run I with theoretical predictions and projections for future measurements in Run II, and (V) new developments in Monte Carlo event generators.

Les Houches 2015: Physics at TeV Colliders Standard Model Working Group Report

CERN Document Server

Andersen, J.R.; Becker, K.; Bell, M.; Bellm, J.; Bendavid, J.; Bothmann, E.; Boughezal, R.; Butterworth, J.; Carrazza, S.; Chiesa, M.; Cieri, L.; Ciulli, V.; Denner, A.; Duehrssen-Debling, M.; Falmagne, G.; Forte, S.; Francavilla, P.; Frederix, R.; Freytsis, M.; Gao, J.; Gras, P.; Grazzini, M.; Greiner, N.; Grellscheid, D.; Heinrich, G.; Hesketh, G.; Hoche, S.; Hofer, L.; Hou, T.J.; Huss, A.; Huston, J.; Isaacson, J.; Jueid, A.; Kallweit, S.; Kar, D.; Kassabov, Z.; Konstantinides, V.; Krauss, F.; Kuttimalai, S.; Lazapoulos, A.; Lenzi, P.; Li, Y.; Lindert, J.M.; Liu, X.; Luisoni, G.; Lonnblad, L.; Maierhofer, P.; Maître, D.; Marini, A.C.; Montagna, G.; Moretti, M.; Nadolsky, P.M.; Nail, G.; Napoletano, D.; Nicrosini, O.; Oleari, C.; Pagani, D.; Pandini, C.; Perrozzi, L.; Petriello, F.; Piccinini, F.; Platzer, S.; Pogrebnyak, I.; Pozzorini, S.; Prestel, S.; Reuschle, C.; Rojo, J.; Russo, L.; Schichtel, P.; Schonherr, M.; Schumann, S.; Siodmok, A.; Skands, P.; Soper, D.; Soyez, G.; Sun, P.; Tackmann, F.J.; Tackmann, K.; Takasugi, E.; Thaler, J.; Uccirati, S.; Utku, U.; Viliani, L.; Vryonidou, E.; Wang, B.T.; Waugh, B.; Weber, M.A.; Williams, C.; Winter, J.; Xie, K.P.; Yuan, C.P.; Yuan, F.; Zapp, K.; Zaro, M.

2016-01-01

This Report summarizes the proceedings of the 2015 Les Houches workshop on Physics at TeV Colliders. Session 1 dealt with (I) new developments relevant for high precision Standard Model calculations, (II) the new PDF4LHC parton distributions, (III) issues in the theoretical description of the production of Standard Model Higgs bosons and how to relate experimental measurements, (IV) a host of phenomenological studies essential for comparing LHC data from Run I with theoretical predictions and projections for future measurements in Run II, and (V) new developments in Monte Carlo event generators.

Integration of THM-experimental work and modelling

International Nuclear Information System (INIS)

Pintado, Xavier; Autio, Jorma; Koskinen, Kari

2010-01-01

Document available in extended abstract form only. Long-term safety of the bentonite buffer relies heavily on appropriate saturation of bentonite buffer resulting evidently on adequate swelling pressure low hydraulic conductivity. After transient period after installation of buffer components the buffer swelling pressure is to remain sufficiently high regardless of e.g. the conditions during the early evolution promoting hydrothermal alteration. For these reasons it is of central importance to characterise different 'underlying saturation flow regimes', USFRs, and the related time dependent fluxes in various parts of buffer in then currently prevailing conditions. The THM processes govern the behaviour from transient to fully saturated state and occur during long periods of time from tens of years up to hundreds or even more. Therefore it is important to be able to understand the underlying processes sufficiently and to develop proper modelling techniques. This can be carried out only by integrating testing and modelling. THM-modelling has also important role in design development phase when different engineering techniques e.g. for wetting of buffer are evaluated. This paper presents the integration of THM-experimental work and modelling carried out in Finland and elsewhere for the development of the buffer designs. The primary objective of this work is to provide experimental and modelling data for assessing the behaviour of bentonite buffer during saturation with respect to fulfilling the performance targets. The development of numerical methods allows to simulate the different processes which take place in materials and to understand them better. In laboratory testing, the numerical methods allow us to simulate the tests and to choose the best geometry and boundary conditions and to verify the experimental designs. The clay barrier behaviour is complex because there are some phenomena coupled: heat flow, water flow in vapour and liquid phases and

Predictive Surface Complexation Modeling

Energy Technology Data Exchange (ETDEWEB)

Sverjensky, Dimitri A. [Johns Hopkins Univ., Baltimore, MD (United States). Dept. of Earth and Planetary Sciences

2016-11-29

Surface complexation plays an important role in the equilibria and kinetics of processes controlling the compositions of soilwaters and groundwaters, the fate of contaminants in groundwaters, and the subsurface storage of CO₂ and nuclear waste. Over the last several decades, many dozens of individual experimental studies have addressed aspects of surface complexation that have contributed to an increased understanding of its role in natural systems. However, there has been no previous attempt to develop a model of surface complexation that can be used to link all the experimental studies in order to place them on a predictive basis. Overall, my research has successfully integrated the results of the work of many experimentalists published over several decades. For the first time in studies of the geochemistry of the mineral-water interface, a practical predictive capability for modeling has become available. The predictive correlations developed in my research now enable extrapolations of experimental studies to provide estimates of surface chemistry for systems not yet studied experimentally and for natural and anthropogenically perturbed systems.

Optimizing the Diffusion Welding Process for Alloy 800H: Thermodynamic, Diffusion Modeling, and Experimental Work

International Nuclear Information System (INIS)

Mizia, R.E.; Clark, D.E.; Glazoff, M.V.; Lister, Tedd E.; Trowbridge, T.L.

2011-01-01

A research effort was made to evaluate the usefulness of modern thermodynamic and diffusion computational tools, Thermo-Calc(copyright) and Dictra(copyright), in optimizing the parameters for diffusion welding of Alloy 800H. This would achieve a substantial reduction in the overall number of experiments required to achieve optimal welding and post-weld heat treatment conditions. This problem is important because diffusion welded components of Alloy 800H are being evaluated for use in assembling compact, micro-channel heat exchangers that are being proposed in the design of a high temperature gas-cooled reactor by the US Department of Energy. The modeling was done in close contact with experimental work. The latter included using the Gleeble 3500 System(reg sign) for welding simulation, mechanical property measurement, and light optical and Scanning Electron Microscopy. The modeling efforts suggested a temperature of 1150 C for 1 hour with an applied pressure of 5 MPa using a 15 μm Ni foil as a joint filler to reduce chromium oxidation on the welded surfaces. Good agreement between modeled and experimentally determined concentration gradients was achieved, and model refinements to account for the complexity of actual alloy materials are suggested.

Experimental evaluation of cooling efficiency of the high performance cooling device

Science.gov (United States)

Nemec, Patrik; Malcho, Milan

2016-06-01

This work deal with experimental evaluation of cooling efficiency of cooling device capable transfer high heat fluxes from electric elements to the surrounding. The work contain description of cooling device, working principle of cooling device, construction of cooling device. Experimental part describe the measuring method of device cooling efficiency evaluation. The work results are presented in graphic visualization of temperature dependence of the contact area surface between cooling device evaporator and electronic components on the loaded heat of electronic components in range from 250 to 740 W and temperature dependence of the loop thermosiphon condenser surface on the loaded heat of electronic components in range from 250 to 740 W.

Experimental evaluation of cooling efficiency of the high performance cooling device

Energy Technology Data Exchange (ETDEWEB)

Nemec, Patrik, E-mail: patrik.nemec@fstroj.uniza.sk; Malcho, Milan, E-mail: milan.malcho@fstroj.uniza.sk [University of Žilina, Faculty of Mechanical Engineering, Department of Power Engineering, Univerzitna 1, 010 26 Žilina (Slovakia)

2016-06-30

This work deal with experimental evaluation of cooling efficiency of cooling device capable transfer high heat fluxes from electric elements to the surrounding. The work contain description of cooling device, working principle of cooling device, construction of cooling device. Experimental part describe the measuring method of device cooling efficiency evaluation. The work results are presented in graphic visualization of temperature dependence of the contact area surface between cooling device evaporator and electronic components on the loaded heat of electronic components in range from 250 to 740 W and temperature dependence of the loop thermosiphon condenser surface on the loaded heat of electronic components in range from 250 to 740 W.

Symmetric and asymmetric capillary bridges between a rough surface and a parallel surface.

Science.gov (United States)

Wang, Yongxin; Michielsen, Stephen; Lee, Hoon Joo

2013-09-03

Although the formation of a capillary bridge between two parallel surfaces has been extensively studied, the majority of research has described only symmetric capillary bridges between two smooth surfaces. In this work, an instrument was built to form a capillary bridge by squeezing a liquid drop on one surface with another surface. An analytical solution that describes the shape of symmetric capillary bridges joining two smooth surfaces has been extended to bridges that are asymmetric about the midplane and to rough surfaces. The solution, given by elliptical integrals of the first and second kind, is consistent with a constant Laplace pressure over the entire surface and has been verified for water, Kaydol, and dodecane drops forming symmetric and asymmetric bridges between parallel smooth surfaces. This solution has been applied to asymmetric capillary bridges between a smooth surface and a rough fabric surface as well as symmetric bridges between two rough surfaces. These solutions have been experimentally verified, and good agreement has been found between predicted and experimental profiles for small drops where the effect of gravity is negligible. Finally, a protocol for determining the profile from the volume and height of the capillary bridge has been developed and experimentally verified.

Study of the interaction of liquid with the surface of mass standards of high accuracy stainless steel

International Nuclear Information System (INIS)

Ramirez Varas, Lautaro; Castro, Claudio S.C.; Cacais, Fabio L.; Pires, Manoel J. M.; Loayza Mendoza, Victor M.

2011-01-01

The long term stability of mass standards depends on the interaction between the surface and environment molecules. From this point of view, a study was investigated of the effect on stainless steel surfaces by liquids frequently used in hydrostatic weighing (FC40) and in cleaning procedures of mass standards (isopropyl alcohol). Firstly, mass weighing difference was measured as function of time with a gravimetric method. Additionally, stainless steel samples were analyzed by X-ray Photoelectron Spectroscopy (XPS). The standard used for the gravimetric mass difference determination was immersed in FC40. The samples analyzed by XPS were previously immersed in both FC40 and isopropyl alcohol. Mass differences were obtained with an uncertainty of 1 μg when FC40 was used. Preliminary results have suggested that FC40 is not chemically bound to stainless steel surfaces and the mass gain was due to physisorbed molecules on the surface. (author) [es

Experimental identification for physical mechanism of fiber-form nanostructure growth on metal surfaces with helium plasma irradiation

Energy Technology Data Exchange (ETDEWEB)

Takamura, S., E-mail: takamura@aitech.ac.jp [Faculty of Engineering, Aichi Institute of Technology, Yakusa-cho, Toyota 470-0392 (Japan); Uesugi, Y. [Faculty of Electrical and Computer Engineering, Institute of Science and Engineering, Kanazawa University, Kanazawa 920-1192 (Japan)

2015-11-30

Highlights: • Initial growth process of fiber-form nanostructure on metal surfaces under helium ion irradiation is given based on experimental knowledge, where the pitting of original surface and forming nano-walls and/or loop-like nanostructure works as precursors. • The physical mechanism of fiber growth is discussed in terms of shear modulus of metals influenced by helium content as well as surface temperature. • The physical model explains the reason why tantalum does not make sufficiently grown nano-fibers, and the temperature dependence of surface morphology of titanium. - Abstract: The initial stage of fiber-form nanostructure growth on metal surface with helium plasma irradiation is illustrated, taking recent research knowledge using a flux gradient technique, and including loop-like nano-scale structure as precursors. The growth mechanism of fibers is discussed in terms of the shear modulus of various materials that is influenced by the helium content as well as the surface temperature, and the mobility of helium atoms, clusters and/or nano-bubbles in the bulk, loops and fibers. This model may explain the reason why tantalum does not provide fiber-form nanostructure although the loop-like structure was identified. The model also suggests the mechanism of an existence of two kinds of nanostructure of titanium depending on surface temperature. Industrial applications of such nanostructures are suggested in the properties and the possibilities of its growth on other basic materials.

Surface passivation of high-purity germanium gamma-ray detector

International Nuclear Information System (INIS)

Alexiev, D.; Butcher, K.S.A.; Edmondson, M.; Lawson, E.M.

1993-01-01

The experimental work consists of two parts. The first involves fabrication of hyper-pure germanium gamma ray detectors using standard surface treatment, chemical etchings and containment in a suitable cryostat. Then, after cooling the detectors to 77 K, γ-ray emissions from radioisotopes are resolved, resolution, depletion depth, V R versus I R characteristics and /N A -N D / of the germanium are measured. The second part of the work involves investigation of surface states in an effort to achieve long-term stability of operating characteristics. Several methods are used: plasma hydrogenation, a-Si and a-Ge pinch-off effect and simple oxidation. A-Ge and a-Si thicknesses were measured using Rutherford backscattering techniques; surface states were measured with deep level transient spectroscopy and diode reverse current versus reverse voltage plots. Some scanning electron microscope measurements were used in determining major film contaminants during backscattering of a-Si and a-Ge films. Surface passivation studies revealed unexpected hole trapping defects generated when a-Ge:H film is applied. The a-Si:H films were found to be mechanically strong, no defect traps were found and preliminary results suggest that such films will be good passivants. 14 refs., 2 tabs., 7 figs., 13 ills

78 FR 34423 - Aviation Rulemaking Advisory Committee (ARAC) Airman Testing Standards and Training Working Group...

Science.gov (United States)

2013-06-07

... the relevance, reliability, validity, and effectiveness of the FAA's aeronautical testing and training... Rulemaking Advisory Committee (ARAC) Airman Testing Standards and Training Working Group (ATSTWG) AGENCY... Certification Standards (ACS) documents developed by the Airman Testing Standards and Training WG for the...

Study of the Fractal and Multifractal Scaling Intervening in the Description of Fracture Experimental Data Reported by the Classical Work: Nature 308, 721–722(1984

Directory of Open Access Journals (Sweden)

Liliana Violeta Constantin

2012-01-01

Full Text Available Starting from the experimental data referring to the main parameters of the fracture surfaces of some 300-grade maraging steel reported by the classical work published in Nature 308, 721–722(1984, this work studied (a the multifractal scaling by the main parameters of the slit islands of fracture surfaces produced by a uniaxial tensile loading and (b the dependence of the impact energy to fracture and of the fractal dimensional increment on the temperature of the studied steels heat treatment, for the fracture surfaces produced by Charpy impact. The obtained results were analyzed, pointing out the spectral (size distribution of the found slit islands in the frame of some specific clusters (fractal components of the multifractal scaling of representative points of the logarithms of the slit islands areas and perimeters, respectively.

Experimental study of gas entrainment from surface swirl

Energy Technology Data Exchange (ETDEWEB)

Moudjed, B., E-mail: brahim.moudjed@cea.fr; Excoffon, J.; Riva, R.; Rossi, L., E-mail: lionel.rossi@cea.fr

2016-12-15

Gas entrainment from surface swirls is characterized using water experiments. A free surface shear flow is generated in an open channel flow. A suction nozzle is set at the bottom of the test section to induce a downward flow and provoke gas entrainment. An important originality of these experiments is the possibility to change the inlet condition so as to generate different turbulent shear flows. This is done by adding obstacles of different sizes and shapes at the end of a flat plate separating the inlet flow from a “stagnant” water area. Velocity fields and profiles, measured with the PIV technique, are provided both to describe the inlet conditions corresponding to various geometries and flow rates, and to characterize the temporal average shear flow generated within the centre part of the channel. Gas entrainment mappings are established from direct observations of the different flow configurations. These new results show that the threshold for the suction velocities required to entrain gas are similar for the configurations with small obstacles and the flat plate configuration triggering a standard shear flow. Increasing the size of the obstacles promotes gas entrainment and reduces the threshold values of the suction velocity to trigger gas entrainment. Shadowgraphy with image processing is used to present new results characterizing the geometrical properties of surface swirls and the quantity of gas entrained. Inlet configurations with obstacles generate larger surface swirls which move upstream from the suction nozzle centre whereas they are situated downstream with the flat plate configuration. Moreover, dimensionless power laws are found to be good approximations for the surface swirl width and the quantity of gas entrained. In addition to provide new insights about gas entrainment in analytical configurations relevant to Sodium cooled fast nuclear reactor, these results should provide different test cases for the validation of MCFD codes.

Polymer-based surface plasmon resonance biochip: construction and experimental aspects

Directory of Open Access Journals (Sweden)

Cleumar da Silva Moreira

Full Text Available Abstract Introduction: Surface plasmon resonance biosensors are high sensitive analytical instruments that normally employ glass materials at the optical substrate layer. However, the use of polymer-based substrates is increasing in the last years due to favorable features, like: disposability, ease to construction and low-cost design. Review Recently, a polymer-based SPR biochip was proposed by using monochromatic and polychromatic input sources. Its construction and experimental considerations are detailed here. Experimental considerations and results, aspects from performance characteristics (resonance parameters, sensitivity and full width at half maximum – FWHM – calculations are presented for hydrophilic and hydrophobic solutions. It is included also a brief description of the state of the art of polymer-based SPR biosensors.

Work function of elemental metals and its face dependence ...

African Journals Online (AJOL)

The calculated work functions for the flat surface of the metals were in perfect agreement with experimental values for metals in the low-density limit and the agreement with experimental values decreased towards the high-density limit. The calculated work functions for the body centred cubic metals were in good agreement ...

Improving the work function of the niobium surface of SRF cavities by plasma processing

International Nuclear Information System (INIS)

Tyagi, P.V.; Doleans, M.; Hannah, B.; Afanador, R.; McMahan, C.; Stewart, S.; Mammosser, J.; Howell, M.; Saunders, J.; Degraff, B.; Kim, S.-H.

2016-01-01

Highlights: • An in situ plasma processing for SNS SRF cavities has been developed to remove hydrocarbons from cavity surface. • Reactive oxygen plasma is very effective to remove hydrocarbons from niobium top surface. • Reactive oxygen plasma processing increases the work function of niobium surface in the range of 0.5–1.0 eV. • It was observed that hydrocarbons can migrate at plasma cleaned top surface from near surface regions when waiting in vacuum at room temperature. • Multiple cycles of plasma processing with waiting periods in between was found beneficial to mitigate such hydrocarbons migration at plasma cleaned surface. - Abstract: An in situ plasma processing technique using chemically reactive oxygen plasma to remove hydrocarbons from superconducting radio frequency cavity surfaces at room temperature has been developed at the spallation neutron source, at Oak Ridge National Laboratory. To understand better the interaction between the plasma and niobium surface, surface studies on small samples were performed. In this article, we report the results from those surface studies. The results show that plasma processing removes hydrocarbons from top surface and improves the surface work function by 0.5–1.0 eV. Improving the work function of RF surface of cavities can help to improve their operational performance.

40 CFR Table 5 to Subpart Ffff of... - Emission Limits and Work Practice Standards for Transfer Racks

Science.gov (United States)

2010-07-01

... Standards for Transfer Racks 5 Table 5 to Subpart FFFF of Part 63 Protection of Environment ENVIRONMENTAL... Limits and Work Practice Standards for Transfer Racks As required in § 63.2475, you must meet each emission limit and work practice standard in the following table that applies to your transfer racks: For...

Improving the work function of the niobium surface of SRF cavities by plasma processing

Science.gov (United States)

Tyagi, P. V.; Doleans, M.; Hannah, B.; Afanador, R.; McMahan, C.; Stewart, S.; Mammosser, J.; Howell, M.; Saunders, J.; Degraff, B.; Kim, S.-H.

2016-04-01

An in situ plasma processing technique using chemically reactive oxygen plasma to remove hydrocarbons from superconducting radio frequency cavity surfaces at room temperature has been developed at the spallation neutron source, at Oak Ridge National Laboratory. To understand better the interaction between the plasma and niobium surface, surface studies on small samples were performed. In this article, we report the results from those surface studies. The results show that plasma processing removes hydrocarbons from top surface and improves the surface work function by 0.5-1.0 eV. Improving the work function of RF surface of cavities can help to improve their operational performance.

Aims and accomplishments of surface theory

International Nuclear Information System (INIS)

Feibelman, P.J.

1979-01-01

The goals of surface science include the understanding of surface structure, transport and chemistry. However, present activities are mainly focussed on the most basic problem, viz., what are the constituents of a given surface and where are they located. Theorists are approaching this surface characterization problem from two sides. To make better use of the data available from the many experimental surface probes, an understanding of the force laws which govern the motion of probe-particles near surfaces is being developed, and the relation between the excitation and ground state spectra of a solid are being studied. In order to develop a predictive capability regarding surface structure, a variety of intrinsic surface properties are being studied, including the nature of bonds at transition metal surfaces, the meaning of bond locality in extended systems, and the electronic factors underlying the forces which govern surface geometry. These studies often raise technical issues such as the validity of using local exchange-correlation potentials and the applicability of cluster calculations to the analysis of extended surface situations, which, however, should not obscure the main thrust of current work - empirical and predictive surface structure determination. These points are illustrated with examples from recent research and ways in which experimental surface work might assist theoretical efforts are indicated

Experimental study of nucleate pool boiling heat transfer of water on silicon oxide nanoparticle coated copper heating surface

International Nuclear Information System (INIS)

Das, Sudev; Kumar, D.S.; Bhaumik, Swapan

2016-01-01

Highlights: • EBPVD approach was employed for fabrication of well-ordered nanoparticle coated micro/nanostructure on metal surface. • Nucleate boiling heat transfer performance on nanoparticle coated micro/nanostructure surface was experimentally studied. • Stability of nanoparticle coated surface under boiling environment was systematically studied. • 58% enhancement of boiling heat transfer coefficient was found. • Present experimental results are validated with well known boiling correlations. - Abstract: Electron beam physical vapor deposition (EBPVD) coating approach was employed for fabrication of well-ordered of nanoparticle coated micronanostructures on metal surfaces. This paper reports the experimental study of augmentation of pool boiling heat transfer performance and stabilities of silicon oxide nanoparticle coated surfaces with water at atmospheric pressure. The surfaces were characterized with respect to dynamic contact angle, surface roughness, topography, and morphology. The results were found that there is a reduction of about 36% in the incipience superheat and 58% enhancement in heat transfer coefficient for silicon oxide coated surface over the untreated surface. This enhancement might be the reason of enhanced wettability, enhanced surface roughness and increased number of a small artificial cavity on a heating surface. The performance and stability of nanoparticle coated micro/nanostructure surfaces were examined and found that after three runs of experiment the heat transfer coefficient with heat flux almost remain constant.

PATENCY AND HEALING OF MICROVASCULAR PROSTHESES - A REVIEW OF 10 YEARS OF EXPERIMENTAL WORK IN GRONINGEN

NARCIS (Netherlands)

VANDERLEI, B; ROBINSON, PH

1993-01-01

From 1982 onwards, in Groningen, The Netherlands, we have worked on the experimental evaluation and development of microvascular prostheses in rats and rabbits. In this review article a systematic overview of this experimental work is presented and the results are discussed with regard to the

Uranium(VI) sorption onto magnetite. Increasing confidence in surface complexation models using chemically evident surface chemistry

Energy Technology Data Exchange (ETDEWEB)

Bok, Frank [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Surface Processes

2017-06-01

Surface complexation models have made great efforts in describing the sorption of various radionuclides on naturally occurring mineral phases. Unfortunately, many of the published sorption parameter sets are built upon unrealistic or even wrong surface chemistry. This work describes the benefit of combining spectroscopic and batch sorption experimental data to create a reliable and consistent surface complexation parameter set.

Experimental study of water droplets on over-heated nano/microstructured zirconium surfaces

Energy Technology Data Exchange (ETDEWEB)

Kim, Seol Ha [Division of Advanced Nuclear Engineering, POSTECH, Pohang 790-784 (Korea, Republic of); Ahn, Ho Seon [Division of Mechanical System Engineering, Incheon National University, 406-772 (Korea, Republic of); Kim, Joonwon [Department of Mechanical Engineering, POSTECH, Pohang 790-784 (Korea, Republic of); Kim, Moo Hwan [Division of Advanced Nuclear Engineering, POSTECH, Pohang 790-784 (Korea, Republic of); Park, Hyun Sun, E-mail: hejsunny@postech.ac.kr [Division of Advanced Nuclear Engineering, POSTECH, Pohang 790-784 (Korea, Republic of)

2014-10-15

Highlights: • Heat transfer performance of a droplet on a modified zirconium surface is evaluated. • Modified (nano/micro-) surfaces enhanced heat transfer rate and Leidenfrost point. • A highly wettable condition of the modified surface contributes the enhancement. • Nano-scaled modification indicates the higher performance of droplet cooling. • Investigation via visualization of the droplet support the heat transfer experimental data. - Abstract: In this study, we observed the behavior of water droplets near the Leidenfrost point (LFP) on zirconium alloy surfaces with anodizing treatment and investigated the droplet cooling performance. The anodized zirconium surface, which consists of bundles of nanotubes (∼10–100 nm) or micro-mountain-like structures, improved the wetting characteristics of the surface. A deionized water droplet (6 μL) was dropped onto test surfaces heated to temperatures ranging from 250 °C to the LFP. The droplet dynamics were investigated through high-speed visualization, and the cooling performance was discussed in terms of the droplet evaporation time. The modified surface provided vigorous, intensive nucleate boiling in comparison with a clean, bare surface. Additionally, we observed that the structured surface had a delayed LFP due to the high wetting condition induced by strong capillary wicking forces on the structured surface.

30 CFR 77.200 - Surface installations; general.

Science.gov (United States)

2010-07-01

... AND HEALTH MANDATORY SAFETY STANDARDS, SURFACE COAL MINES AND SURFACE WORK AREAS OF UNDERGROUND COAL... other facilities (including custom coal preparation) shall be maintained in good repair to prevent accidents and injuries to employees. ...

Electron work function of stepped tungsten surfaces

International Nuclear Information System (INIS)

Krahl-Urban, B.

1976-03-01

The electron work function of tungsten (110) vicinal faces was measured with the aid of thermionic emission, and its dependence on the crystallographic orientation and the surface structure was investigated. The thermionic measurements were evaluated with the aid of the Richardson plot. The real temperature of the emitting tungsten faces was determined with an accuracy of +- 0.5% in the range between 2,200 and 2,800 K. The vicinal faces under investigation have been prepared with an orientation exactness of +- 15'. In the tungsten (110) vicinal faces under investigation, a strong dependence of the temperature coefficient d PHI/dT of the work function on the crystallographic orientation was found. A strong influence of the edge structure as well as of the step density on the temperature coefficient was observed. (orig./HPOE) [de

Effects of surface condition on the work function and valence-band position of ZnSnN2

Science.gov (United States)

Shing, Amanda M.; Tolstova, Yulia; Lewis, Nathan S.; Atwater, Harry A.

2017-12-01

ZnSnN2 is an emerging wide band gap earth-abundant semiconductor with potential applications in photonic devices such as solar cells, LEDs, and optical sensors. We report the characterization by ultraviolet photoelectron spectroscopy and X-ray photoelectron spectroscopy of reactively radio-frequency sputtered II-IV-nitride ZnSnN2 thin films. For samples transferred in high vacuum, the ZnSnN2 surface work function was 4.0 ± 0.1 eV below the vacuum level, with a valence-band onset of 1.2 ± 0.1 eV below the Fermi level. The resulting band diagram indicates that the degenerate bulk Fermi level position in ZnSnN2 shifts to mid-gap at the surface due to band bending that results from equilibration with delocalized surface states within the gap. Brief (< 10 s) exposures to air, a nitrogen-plasma treatment, or argon-ion sputtering caused significant chemical changes at the surface, both in surface composition and interfacial energetics. The relative band positioning of the n-type semiconductor against standard redox potentials indicated that ZnSnN2 has an appropriate energy band alignment for use as a photoanode to effect the oxygen-evolution reaction.

Experimental study of the strain state at the area of a surface defect in a steel cylindrical shell subjected to internal pressure

OpenAIRE

Бесчетников, Д. А.

2014-01-01

Experimental research of stress-strain state at the area of local volumetric surface defects of the pipeline systems is an important goal because results of the measurements are necessary for increasing of effectiveness of existing repair technologies using fiber reinforcement polymer composite materials. In this work the description of experiment carried out by the author is presented with statement of results. The experiment was devoted to strain gauging of a steel cylindrical shell with vo...

Efficiency calibration of electron spectrometers by the help of standard spectrum

International Nuclear Information System (INIS)

Toth, J.; Cserny, I.; Varga, D.; Koever, I.; Toekesi, K.

2004-01-01

Complete text of publication follows. For studying thin films and surface nanostructures quantitative analytical applications of electron spectroscopic techniques have a great importance. The most frequently used techniques are XPS, XAES and AES in quantitative surface electron spectroscopy. Applying these techniques changes in the detection efficiency vs. electron kinetic energy change the measured electron peak intensity ratios and in this way the neglect of the energy dependence of the spectrometer efficiency can influence surface atomic concentrations derived. The importance of the precise determination of the atomic concentrations is very crucial, especially in the determination of non-destructive depth profiles by the help of AR-XPS in which small changes in the relative concentrations can change dramatically the concentration depth profiles of a few nanometer depth ranges. In the present study the REELS technique was used to determine the relative detection efficiency by the help of a standard spectrum measured on the surface of fine microcrystalline Cu specimen. The experimental relative efficiency curves vs. electron kinetic energy were compared to the calculated efficiency curve. The efficiency calibration is discussed from the point of view of quantitative XPS, AR- XPS, AES and from the point of view of IMFP determination by XPS. The work was supported by the Hungarian National Science Foundation, OTKAT038016. For the Cu specimen and the standard spectrum the authors are indebted to the Sur- face Analysis Society of Japan, to Dr. Shigeo Tanuma and Professor Keisuke Goto (NIT). (author)

De invloed van afwijkende werktijden op de werkthuis situatie [The influence of working at non-standard working hours on the workhome situation

NARCIS (Netherlands)

Hooff, L.M. van; Bakhuys Roozeboom, M.M.C.; Vroome, E.M.M. de; Smulders, P.G.W.

2010-01-01

The present study was designed to map the causal relationships between nonstandard working hours and work-home interference (WHI) and home-work interference (HWI). To this purpose, a longitudinal full-panel design was employed. Using such a design, we examined both the causal effects of non-standard

Incorporating Skew into RMS Surface Roughness Probability Distribution

Science.gov (United States)

Stahl, Mark T.; Stahl, H. Philip.

2013-01-01

The standard treatment of RMS surface roughness data is the application of a Gaussian probability distribution. This handling of surface roughness ignores the skew present in the surface and overestimates the most probable RMS of the surface, the mode. Using experimental data we confirm the Gaussian distribution overestimates the mode and application of an asymmetric distribution provides a better fit. Implementing the proposed asymmetric distribution into the optical manufacturing process would reduce the polishing time required to meet surface roughness specifications.

Experimental High-Resolution Land Surface Prediction System for the Vancouver 2010 Winter Olympic Games

Science.gov (United States)

Belair, S.; Bernier, N.; Tong, L.; Mailhot, J.

2008-05-01

The 2010 Winter Olympic and Paralympic Games will take place in Vancouver, Canada, from 12 to 28 February 2010 and from 12 to 21 March 2010, respectively. In order to provide the best possible guidance achievable with current state-of-the-art science and technology, Environment Canada is currently setting up an experimental numerical prediction system for these special events. This system consists of a 1-km limited-area atmospheric model that will be integrated for 16h, twice a day, with improved microphysics compared with the system currently operational at the Canadian Meteorological Centre. In addition, several new and original tools will be used to adapt and refine predictions near and at the surface. Very high-resolution two-dimensional surface systems, with 100-m and 20-m grid size, will cover the Vancouver Olympic area. Using adaptation methods to improve the forcing from the lower-resolution atmospheric models, these 2D surface models better represent surface processes, and thus lead to better predictions of snow conditions and near-surface air temperature. Based on a similar strategy, a single-point model will be implemented to better predict surface characteristics at each station of an observing network especially installed for the 2010 events. The main advantage of this single-point system is that surface observations are used as forcing for the land surface models, and can even be assimilated (although this is not expected in the first version of this new tool) to improve initial conditions of surface variables such as snow depth and surface temperatures. Another adaptation tool, based on 2D stationnary solutions of a simple dynamical system, will be used to produce near-surface winds on the 100-m grid, coherent with the high- resolution orography. The configuration of the experimental numerical prediction system will be presented at the conference, together with preliminary results for winter 2007-2008.

An experimental result of surface roughness machining performance in deep hole drilling

Directory of Open Access Journals (Sweden)

Mohamad Azizah

2016-01-01

Full Text Available This study presents an experimental result of a deep hole drilling process for Steel material at different machining parameters which are feed rate (f, spindle speed (s, the depth of the hole (d and MQL, number of drops (m on surface roughness, Ra. The experiment was designed using two level full factorial design of experiment (DoE with centre points to collect surface roughness, Ra values. The signal to noise (S/N ratio analysis was used to discover the optimum level for each machining parameters in the experiment.

Standard Model theory calculations and experimental tests

International Nuclear Information System (INIS)

Cacciari, M.; Hamel de Monchenault, G.

2015-01-01

To present knowledge, all the physics at the Large Hadron Collider (LHC) can be described in the framework of the Standard Model (SM) of particle physics. Indeed the newly discovered Higgs boson with a mass close to 125 GeV seems to confirm the predictions of the SM. Thus, besides looking for direct manifestations of the physics beyond the SM, one of the primary missions of the LHC is to perform ever more stringent tests of the SM. This requires not only improved theoretical developments to produce testable predictions and provide experiments with reliable event generators, but also sophisticated analyses techniques to overcome the formidable experimental environment of the LHC and perform precision measurements. In the first section, we describe the state of the art of the theoretical tools and event generators that are used to provide predictions for the production cross sections of the processes of interest. In section 2, inclusive cross section measurements with jets, leptons and vector bosons are presented. Examples of differential cross sections, charge asymmetries and the study of lepton pairs are proposed in section 3. Finally, in section 4, we report studies on the multiple production of gauge bosons and constraints on anomalous gauge couplings

Simultaneous measurements of work function and H‒ density including caesiation of a converter surface

Science.gov (United States)

Cristofaro, S.; Friedl, R.; Fantz, U.

2017-08-01

Negative hydrogen ion sources rely on the surface conversion of neutral atomic hydrogen and positive hydrogen ions to H-. The efficiency of this process depends on the actual work function of the converter surface. By introducing caesium into the source the work function decreases, enhancing the negative ion yield. In order to study the impact of the work function on the H- surface production at similar conditions to the ones in ion sources for fusion devices like ITER and DEMO, fundamental investigations are performed in a flexible laboratory experiment. The work function of the converter surface can be absolutely measured by photoelectric effect, while a newly installed cavity ring-down spectroscopy system (CRDS) measures the H- density. The CRDS is firstly tested and characterized by investigations on H- volume production. Caesiation of a stainless steel sample is then performed in vacuum and the plasma effect on the Cs layer is investigated also for long plasma-on times. A minimum work function of (1.9±0.1) eV is reached after some minutes of plasma treatment, resulting in a reduction by a value of 0.8 eV compared to vacuum measurements. The H- density above the surface is (2.1±0.5)×1015 m-3. With further plasma exposure of the caesiated surface, the work function increases up to 3.75 eV, due to the impinging plasma particles which gradually remove the Cs layer. As a result, the H- density decreases by a factor of at least 2.

Working out the standards for nuclear power aging management implementation (PLM Standards)

International Nuclear Information System (INIS)

Miyano, Hiroshi

2008-01-01

Background of preparation of standards, preparation of standards for development of nuclear power aging management technologies, revision of PLM (Product Lifecycle Management) standards, and problems of PLM standards are stated. The placement of social needs, scheme, the standards system, preparation of rules and standards, and practical use of them by road map are illustrated and explained. Relation between the safety regulations and examination standards, and development and preparation of standards system are outlined. The nuclear power plant aging management and the maintenance control are provided by many rules and standards. PLM standards defines the aging phenomena and extracts the measurements and reflects them on the usual maintenance flow under the long term maintenance program. New examination system constructs the usual maintenance and the maintenance based on the aging management and long term maintenance program. Outline and construction of PLM standards are explained with notes and additional books. (S.Y.)

Experimental 3-D modelling of surface subsidence affected by underground mining activities

Czech Academy of Sciences Publication Activity Database

Trčková, Jiřina

2009-01-01

Roč. 109, č. 12 (2009), s. 739-744 ISSN 0038-223X R&D Projects: GA AV ČR IAA2119402 Institutional research plan: CEZ:AV0Z30460519 Keywords : undermining * subsidence of surface * 3-D experimental model Subject RIV: DO - Wilderness Conservation Impact factor: 0.216, year: 2009

Project report: Experimental planning and verification of working fluids (WP 5)

DEFF Research Database (Denmark)

Babi, Deenesh Kavi

working fluid candidates a database is required that can be simultaneously searched in order to differentiate and determine whether the generated candidates are existing or novel. Also, the next step upon selection of the candidates is performing experiments in order to test and verify the generated...... working fluids. If performed properly, the experimental step is solely verification. Experiments can either be performed virtually (in order to further reduce the number of required experiments) and/or physically. Therefore the objective of this work was the development of a database of existing working......Computer-aided molecular design (CAMD) helps in the reduction of experiments for the selection/design of optimal working fluids. In reducing the number of experiments, solutions obtain by trial and error is replaced by solutions that are based on mixture-process properties. In generating optimal...

Standard test method for damage to contacting solid surfaces under fretting conditions

CERN Document Server

American Society for Testing and Materials. Philadelphia

2010-01-01

1.1 This test method covers the studying or ranking the susceptibility of candidate materials to fretting corrosion or fretting wear for the purposes of material selection for applications where fretting corrosion or fretting wear can limit serviceability. 1.2 This test method uses a tribological bench test apparatus with a mechanism or device that will produce the necessary relative motion between a contacting hemispherical rider and a flat counterface. The rider is pressed against the flat counterface with a loading mass. The test method is intended for use in room temperature air, but future editions could include fretting in the presence of lubricants or other environments. 1.3 The purpose of this test method is to rub two solid surfaces together under controlled fretting conditions and to quantify the damage to both surfaces in units of volume loss for the test method. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5...

Work Function of Oxide Ultrathin Films on the Ag(100) Surface.

Science.gov (United States)

Sementa, Luca; Barcaro, Giovanni; Negreiros, Fabio R; Thomas, Iorwerth O; Netzer, Falko P; Ferrari, Anna Maria; Fortunelli, Alessandro

2012-02-14

Theoretical calculations of the work function of monolayer (ML) and bilayer (BL) oxide films on the Ag(100) surface are reported and analyzed as a function of the nature of the oxide for first-row transition metals. The contributions due to charge compression, charge transfer and rumpling are singled out. It is found that the presence of empty d-orbitals in the oxide metal can entail a charge flow from the Ag(100) surface to the oxide film which counteracts the decrease in the work function due to charge compression. This flow can also depend on the thickness of the film and be reduced in passing from ML to BL systems. A regular trend is observed along first-row transition metals, exhibiting a maximum for CuO, in which the charge flow to the oxide is so strong as to reverse the direction of rumpling. A simple protocol to estimate separately the contribution due to charge compression is discussed, and the difference between the work function of the bare metal surface and a Pauling-like electronegativity of the free oxide slabs is used as a descriptor quantity to predict the direction of charge transfer.

Light scattering by sinusoidal surfaces: illumination windows and harmonics in standards.

Science.gov (United States)

Marx, E; Lettieri, T R; Vorburger, T V

1995-03-01

Sinusoidal surfaces can be used as material standards to help calibrate instruments that measure the angular distribution of the intensity of light scattered by arbitrary surfaces, because the power in the diffraction peaks varies over several orders of magnitude. The calculated power in the higher-order diffraction peaks from sinusoidal surfaces expressed in terms of Bessel functions is much smaller than the values determined from angular distributions that are measured or computed from measured profiles, both of which are determined mainly by the harmonic contents of the profile. The finite size of the illuminated area, represented by an illumination window, gives rise to a background that is much larger than the calculated power in the higher-order peaks. For a rectangular window of a size equal to an even number of periods of the sinusoid, a computation of the power distribution produces minima at or near the location of the diffraction angles for higher-order diffraction angles.

Experimental vortex breakdown topology in a cylinder with a free surface

DEFF Research Database (Denmark)

Lo Jacono, D.; Nazarinia, M.; Brøns, Morten

2009-01-01

The free SLII-face, flow in it circular cylinder driven by a rotating bottom disk IS Studied experimentally using particle image velocimetry. Results are compared With computational,11 results assuming I stress-free surface A dye visualization Study by Spohn et al ["Observations of vortex breakdown...... in in open cylindrical container with I rotating bottom," Exp. Fluids 14. 70 (1993)]v as well as several numerical computations. has found a range of different vortex breakdown Structures in this flow. We confirm the existence of a transition where the top of the breakdown bubble crosses from the axis...... to the surface, which has previously only been found numerically. We employ a technique by Brons et al ["Topology of vortex breakdown bubbles in I cylinder with rotating bottom and free surface J. Fluid Mech 428. 133 (2001)] to find the corresponding bifurcation curve in the parameter plane, which has hitherto...

Experimental assessment of film cooling performance of short cylindrical holes on a flat surface

Science.gov (United States)

Singh, Kuldeep; Premachandran, B.; Ravi, M. R.

2016-12-01

The present study is an experimental investigation of film-cooling over a flat surface from the short cylindrical holes. The film cooling holes used in the combustion chamber and the afterburner liner of an aero engine has length-to-diameter (L/D) typically in the range 1-2, while the cooling holes used in turbine blades has L/D > 3. Based on the classification given in the literature, cooling holes with L/D ≤ 3 are named as short holes and cooling holes with L/D > 3 are named as long holes. Short film cooling holes cause jetting of the secondary fluid whereas the secondary fluid emerging from long holes has characteristics similar to fully developed turbulent flow in pipe. In order to understand the difference in the film cooling performance of long and short cooling holes, experimental study is carried out for five values of L/D in the range 1-5, five injection angles, α = 15°-90° and five mainstream Reynolds number 1.25 × 105-6.25 × 105 and two blowing ratios, M = 0.5-1.0. The surface temperature of the test plate is monitored using infrared thermography. The results obtained from the present study showed that the film-cooling effectiveness is higher for the longest holes (L/D = 5) investigated in the present work in comparison to that for the shorter holes. Short holes are found to give better effectiveness at the lowest investigated injection angle i.e. α = 15° in the near cooling hole region, whereas film cooling effectiveness obtained at injection angle, α = 45° is found to be better than other injection angles for longest investigated holes, i.e. L/D = 5.

Experimental Study of Plasma-Surface Interaction and Material Damage Relevant to ITER Type I Elms

International Nuclear Information System (INIS)

Makhlai, V.A.; Bandura, A.N.; Byrka, O.V. and others; Landman, I.; Neklyudov, I.M.

2006-01-01

The paper presents experimental investigations of main features of plasma surface interaction and energy transfer to the material surface in dependence on plasma heat loads. The experiments were performed with QSPA repetitive plasma pulses of the duration of 0.25 ms and the energy density up to 2.5 MJ/m 2 . Surface morphology of the targets exposed to QSPA plasma screams is analyzed. Relative contribution of the Lorentz force and plasma pressure gradient to the resulting surface profile is discussed. development of cracking on the tungsten surface and swelling of the surface are found to be in strong dependence on initial temperature of the target

Primary role of electron work function for evaluation of nanostructured titania implant surface against bacterial infection

Energy Technology Data Exchange (ETDEWEB)

Golda-Cepa, M., E-mail: golda@chemia.uj.edu.pl [Faculty of Chemistry, Jagiellonian University, Ingardena 3, 30-060 Krakow (Poland); Syrek, K. [Faculty of Chemistry, Jagiellonian University, Ingardena 3, 30-060 Krakow (Poland); Brzychczy-Wloch, M. [Department of Bacteriology, Microbial Ecology and Parasitology, Jagiellonian University Medical College, Czysta 18, 31-121 Krakow (Poland); Sulka, G.D. [Faculty of Chemistry, Jagiellonian University, Ingardena 3, 30-060 Krakow (Poland); Kotarba, A., E-mail: kotarba@chemia.uj.edu.pl [Faculty of Chemistry, Jagiellonian University, Ingardena 3, 30-060 Krakow (Poland)

2016-09-01

The electron work function as an essential descriptor for the evaluation of metal implant surfaces against bacterial infection is identified for the first time. Its validity is demonstrated on Staphylococcus aureus adhesion to nanostructured titania surfaces. The established correlation: work function–bacteria adhesion is of general importance since it can be used for direct evaluation of any electrically conductive implant surfaces. - Highlights: • The correlation between work function and bacteria adhesion was discovered. • The discovered correlation is rationalized in terms of electrostatic bacteria–surface repulsion. • The results provide basis for the simple evaluation of implant surfaces against infection.

Primary role of electron work function for evaluation of nanostructured titania implant surface against bacterial infection

International Nuclear Information System (INIS)

Golda-Cepa, M.; Syrek, K.; Brzychczy-Wloch, M.; Sulka, G.D.; Kotarba, A.

2016-01-01

The electron work function as an essential descriptor for the evaluation of metal implant surfaces against bacterial infection is identified for the first time. Its validity is demonstrated on Staphylococcus aureus adhesion to nanostructured titania surfaces. The established correlation: work function–bacteria adhesion is of general importance since it can be used for direct evaluation of any electrically conductive implant surfaces. - Highlights: • The correlation between work function and bacteria adhesion was discovered. • The discovered correlation is rationalized in terms of electrostatic bacteria–surface repulsion. • The results provide basis for the simple evaluation of implant surfaces against infection.

Understanding of the correlation between work function and surface morphology of metals and alloys

International Nuclear Information System (INIS)

Xue, Mingshan; Wang, Wenfeng; Wang, Fajun; Ou, Junfei; Li, Changquan; Li, Wen

2013-01-01

Highlights: •The inherent correlation between the work function and surface morphology was focused on. •The change of the work function of metals and alloys as a function of surface roughness was investigated by scanning Kelvin probe. •The lightning rod effect was used to describe the electron transport at a rough surface. -- Abstract: The relationships between material behaviors and its structures are extremely complicated, and the understanding of these relationships is of much significance for revealing the physical, chemical and mechanical properties of various materials. In this study, the change of the work function (WF) of metals and alloys as a function of surface roughness was investigated by scanning Kelvin probe, with the aim of understanding the inherent correlation between the WF and surface morphology using a simple and intuitive way. It was demonstrated that at the rough surface of Cu and Ag, the sharp micro/nanostructures induced a lower WF, just as the lightning rod effect providing a direct and fast path for electron transport. While for Al and Mg alloys, the rough surface resulted in an increase of the WF owing to the effect of surface oxide layers, just as the anti-lightning rod effect providing a protected layer to confine the electron transport

Investigation of Vacuum Insulator Surface Dielectric Strength with Nanosecond Pulses

International Nuclear Information System (INIS)

Nunnally, W.C.; Krogh, M.; Williams, C.; Trimble, D.; Sampayan, S.; Caporaso, G.

2003-01-01

The maximum vacuum insulator surface dielectric strength determines the acceleration electric field gradient possible in a short pulse accelerator. Previous work has indicated that higher electric field strengths along the insulator-vacuum interface might be obtained as the pulse duration is decreased. In this work, a 250 kV, single ns wide impulse source was applied to small diameter, segmented insulators samples in a vacuum to evaluate the multi-layer surface dielectric strength of the sample construction. Resonances in the low inductance test geometry were used to obtain unipolar, pulsed electric fields in excess of 100 MV/m on the insulator surface. The sample construction, experimental arrangement and experimental results are presented for the initial data in this work. Modeling of the multi-layer structure is discussed and methods of improving insulator surface dielectric strength in a vacuum are proposed

Harmonization of nuclear codes and standards, pacific nuclear council working and task group report

International Nuclear Information System (INIS)

Dua, S.S.

2006-01-01

Full text: The codes and standards, both at the national and international level, have had a major impact on the industry worldwide and served it well in maintaining the performance and safety of the nuclear reactors and facilities. The codes and standards, in general, are consensus documents and do seek public input at various levels before they are finalized and rolled out for use by the nuclear vendors, consultants, utilities and regulatory bodies. However, the extensive development of prescriptive national standards if unchecked against the global environment and trade agreements (NAFTA, WTO, etc.) can also become barriers and cause difficulties to compete in the world market. During the last decade, the national and international writing standards writing bodies have recognized these issues and are moving more towards the rationalization and harmonization of their standards with the more widely accepted generic standards. The Pacific Nuclear Council (PNC) recognized the need for harmonization of the nuclear codes and standards for its member countries and formed a Task Group to achieve its objectives. The Task Group has a number of members from the PNC member countries. In 2005 PNC further raised the importance of this activity and formed a Working Group to cover a broader scope. The Working Group (WG) mandate is to identify and analyze the different codes and standards introduced to the Pacific Basin region, in order to achieve mutual understanding, harmonization and application in each country. This o requires the WG to develop and encourage the use of reasonably consistent criteria for the design and development, engineering, procurement, fabrication, construction, testing, operations, maintenance, waste management, decommissioning and the management of the commercial nuclear power plants in the Pacific Basin so as to: Promote consistent safety, quality, environmental and management standards for nuclear energy and other peaceful applications of nuclear

Final Report. An Integrated Partnership to Create and Lead the Solar Codes and Standards Working Group

Energy Technology Data Exchange (ETDEWEB)

Rosenthal, Andrew [New Mexico State Univ., Las Cruces, NM (United States)

2013-12-30

The DOE grant, “An Integrated Partnership to Create and Lead the Solar Codes and Standards Working Group,” to New Mexico State University created the Solar America Board for Codes and Standards (Solar ABCs). From 2007 – 2013 with funding from this grant, Solar ABCs identified current issues, established a dialogue among key stakeholders, and catalyzed appropriate activities to support the development of codes and standards that facilitated the installation of high quality, safe photovoltaic systems. Solar ABCs brought the following resources to the PV stakeholder community; Formal coordination in the planning or revision of interrelated codes and standards removing “stove pipes” that have only roofing experts working on roofing codes, PV experts on PV codes, fire enforcement experts working on fire codes, etc.; A conduit through which all interested stakeholders were able to see the steps being taken in the development or modification of codes and standards and participate directly in the processes; A central clearing house for new documents, standards, proposed standards, analytical studies, and recommendations of best practices available to the PV community; A forum of experts that invites and welcomes all interested parties into the process of performing studies, evaluating results, and building consensus on standards and code-related topics that affect all aspects of the market; and A biennial gap analysis to formally survey the PV community to identify needs that are unmet and inhibiting the market and necessary technical developments.

A general phenomenological model for work function

Science.gov (United States)

Brodie, I.; Chou, S. H.; Yuan, H.

2014-07-01

A general phenomenological model is presented for obtaining the zero Kelvin work function of any crystal facet of metals and semiconductors, both clean and covered with a monolayer of electropositive atoms. It utilizes the known physical structure of the crystal and the Fermi energy of the two-dimensional electron gas assumed to form on the surface. A key parameter is the number of electrons donated to the surface electron gas per surface lattice site or adsorbed atom, which is taken to be an integer. Initially this is found by trial and later justified by examining the state of the valence electrons of the relevant atoms. In the case of adsorbed monolayers of electropositive atoms a satisfactory justification could not always be found, particularly for cesium, but a trial value always predicted work functions close to the experimental values. The model can also predict the variation of work function with temperature for clean crystal facets. The model is applied to various crystal faces of tungsten, aluminium, silver, and select metal oxides, and most demonstrate good fits compared to available experimental values.

Experimental Study on Momentum Transfer of Surface Texture in Taylor-Couette Flow

Science.gov (United States)

Xue, Yabo; Yao, Zhenqiang; Cheng, De

2017-05-01

The behavior of Taylor-Couette (TC) flow has been extensively studied. However, no suitable torque prediction models exist for high-capacity fluid machinery. The Eckhardt-Grossmann-Lohse (EGL) theory, derived based on the Navier-Stokes equations, is proposed to model torque behavior. This theory suggests that surfaces are the significant energy transfer interfaces between cylinders and annular flow. This study mainly focuses on the effects of surface texture on momentum transfer behavior through global torque measurement. First, a power-law torque behavior model is built to reveal the relationship between dimensionless torque and the Taylor number based on the EGL theory. Second, TC flow apparatus is designed and built based on the CNC machine tool to verify the torque behavior model. Third, four surface texture films are tested to check the effects of surface texture on momentum transfer. A stereo microscope and three-dimensional topography instrument are employed to analyze surface morphology. Global torque behavior is measured by rotating a multi component dynamometer, and the effects of surface texture on the annular flow behavior are observed via images obtained using a high-speed camera. Finally, torque behaviors under four different surface conditions are fitted and compared. The experimental results indicate that surface textures have a remarkable influence on torque behavior, and that the peak roughness of surface texture enhances the momentum transfer by strengthening the fluctuation in the TC flow.

The influence of working memory capacity on experimental heat pain.

Science.gov (United States)

Nakae, Aya; Endo, Kaori; Adachi, Tomonori; Ikeda, Takashi; Hagihira, Satoshi; Mashimo, Takashi; Osaka, Mariko

2013-10-01

Pain processing and attention have a bidirectional interaction that depends upon one's relative ability to use limited-capacity resources. However, correlations between the size of limited-capacity resources and pain have not been evaluated. Working memory capacity, which is a cognitive resource, can be measured using the reading span task (RST). In this study, we hypothesized that an individual's potential working memory capacity and subjective pain intensity are related. To test this hypothesis, we evaluated 31 healthy participants' potential working memory capacity using the RST, and then applied continuous experimental heat stimulation using the listening span test (LST), which is a modified version of the RST. Subjective pain intensities were significantly lower during the challenging parts of the RST. The pain intensity under conditions where memorizing tasks were performed was compared with that under the control condition, and it showed a correlation with potential working memory capacity. These results indicate that working memory capacity reflects the ability to process information, including precise evaluations of changes in pain perception. In this work, we present data suggesting that changes in subjective pain intensity are related, depending upon individual potential working memory capacities. Individual working memory capacity may be a phenotype that reflects sensitivity to changes in pain perception. Copyright © 2013 American Pain Society. Published by Elsevier Inc. All rights reserved.

Experimental and QSAR study on the surface activities of alkyl imidazoline surfactants

Science.gov (United States)

Kong, Xiangjun; Qian, Chengduo; Fan, Weiyu; Liang, Zupei

2018-03-01

15 alkyl imidazoline surfactants with different structures were synthesized and their critical micelle concentration (CMC) and surface tension under the CMC (σcmc) in aqueous solution were measured at 298 K. 54 kinds of molecular structure descriptors were selected as independent variables and the quantitative structure-activity relationship (QSAR) between surface activities of alkyl imidazoline and molecular structure were built through the genetic function approximation (GFA) method. Experimental results showed that the maximum surface excess of alkyl imidazoline molecules at the gas-liquid interface increased and the area occupied by each surfactant molecule and the free energies of micellization ΔGm decreased with increasing carbon number (NC) of the hydrophobic chain or decreasing hydrophilicity of counterions, which resulted in a CMC and σcmc decrease, while the log CMC and NC had a linear relationship and a negative correlation. The GFA-QSAR model, which was generated by a training set composed of 13 kinds of alkyl imidazoline though GFA method regression analysis, was highly correlated with predicted values and experimental values of the CMC. The correlation coefficient R was 0.9991, which means high prediction accuracy. The prediction error of 2 kinds of alkyl imidazoline CMCs in the Validation Set that quantitatively analyzed the influence of the alkyl imidazoline molecular structure on the CMC was less than 4%.

Experimental Determination of Temperatures in a Liquid GAP

International Nuclear Information System (INIS)

Masson, Viviana; Ojeda, Andres; Fabian, Bonetto

2003-01-01

An experimental study of heat transfer in a gap of water at atmospheric pressure is presented under natural convection conditions.The objective of the work was to experimentally determine the expected maximum temperatures in the gap for a given heater power.The experimental set-up was a plane surface heated by resistances and facing a 1mm-liquid gap.Visualisation of phenomena by video and still picture was performed

Standard Deviation of Spatially-Averaged Surface Cross Section Data from the TRMM Precipitation Radar

Science.gov (United States)

Meneghini, Robert; Jones, Jeffrey A.

2010-01-01

We investigate the spatial variability of the normalized radar cross section of the surface (NRCS or Sigma(sup 0)) derived from measurements of the TRMM Precipitation Radar (PR) for the period from 1998 to 2009. The purpose of the study is to understand the way in which the sample standard deviation of the Sigma(sup 0) data changes as a function of spatial resolution, incidence angle, and surface type (land/ocean). The results have implications regarding the accuracy by which the path integrated attenuation from precipitation can be inferred by the use of surface scattering properties.

Experimental studies on radiation heat transfer enhancement on a standard muffle furnace

Directory of Open Access Journals (Sweden)

Minea Alina Adriana

2013-01-01

Full Text Available One of the sources of increased industrial energy consumption is the heating equipment, e.g., furnaces. Their domain of use is very wide and due to its abundance of applications it is key equipment in modern civilization. The present experimental investigations are related to reducing energy consumptions and started from the geometry of a classic manufactured furnace. During this experimental study, different cases have been carefully chosen in order to compare and measure the effects of applying different enhancement methods of the radiation heat transfer processes. The main objective work was to evaluate the behavior of a heated enclosure, when different radiant panels were introduced. The experimental investigation showed that their efficiency was influenced by their position inside the heating area. In conclusion, changing the inner geometry by introducing radiant panels inside the heated chamber leads to important time savings in the heating process.

Experimental analysis on removal factor of smear method in measurement of surface contamination

International Nuclear Information System (INIS)

Sugiura, Nobuyuki; Taira, Junichi; Takenaka, Keisuke; Yamanaka, Kazuo; Sugai, Kenji; Kosako, Toshiso

2007-01-01

The smear test is one of the important ways to measure surface contamination. The loose contamination under the high background radiation, which is more significant in handling non-sealed radioisotopes, can be evaluated by this method. The removal factor is defined as the ratio of the activity removed from the surface by one smear to the whole activity of the removable surface contamination. The removal factor is greatly changed by the quality and condition of surface materials. In this study, the values of removal factor at several typical surface conditions were evaluated experimentally and the practical application of those values was considered. It is required the smear should be pressed by moderate pressure when wiping the surface. The pressure from 1.0 kg to 1.5 kg per filter paper was recommended. The removal factor showed lower value in wiping by the pressure below 1.0 kg. The value of 0.5 for the removal factor could be applied to the smooth surface of linoleum, concrete coated with paint or epoxy resin, stainless steel and glass with the statistical allowance. (author)

Experimental Study on GFRP Surface Cracks Detection Using Truncated-Correlation Photothermal Coherence Tomography

Science.gov (United States)

Wang, Fei; Liu, Junyan; Mohummad, Oliullah; Wang, Yang

2018-04-01

In this paper, truncated-correlation photothermal coherence tomography (TC-PCT) was used as a nondestructive inspection technique to evaluate glass-fiber reinforced polymer (GFRP) composite surface cracks. Chirped-pulsed signal that combines linear frequency modulation and pulse excitation was proposed as an excitation signal to detect GFRP composite surface cracks. The basic principle of TC-PCT and extraction algorithm of the thermal wave signal feature was described. The comparison experiments between lock-in thermography, thermal wave radar imaging and chirped-pulsed photothermal radar for detecting GFRP artificial surface cracks were carried out. Experimental results illustrated that chirped-pulsed photothermal radar has the merits of high signal-to-noise ratio in detecting GFRP composite surface cracks. TC-PCT as a depth-resolved photothermal imaging modality was employed to enable three-dimensional visualization of GFRP composite surface cracks. The results showed that TC-PCT can effectively evaluate the cracks depth of GFRP composite.

A Sandbox Environment for the CSM Standard and SPICE

Science.gov (United States)

Hare, T. M.; Laura, J. R.

2018-04-01

We present ongoing work USGS is undertaking to provide a programming environment for the Camera Sensor Model (CSM) standard and associated SPICE information. This allows for instrument testing and experimentation outside a given production area.

Survey of basic medical researchers on the awareness of animal experimental designs and reporting standards in China.

Directory of Open Access Journals (Sweden)

Bin Ma

Full Text Available To investigate the awareness and use of the Systematic Review Center for Laboratory Animal Experimentation's (SYRCLE risk-of-bias tool, the Animal Research: Reporting of In Vivo Experiments (ARRIVE reporting guidelines, and Gold Standard Publication Checklist (GSPC in China in basic medical researchers of animal experimental studies.A national questionnaire-based survey targeting basic medical researchers was carried in China to investigate the basic information and awareness of SYRCLE's risk of bias tool, ARRIVE guidelines, GSPC, and animal experimental bias risk control factors. The EpiData3.1 software was used for data entry, and Microsoft Excel 2013 was used for statistical analysis in this study. The number of cases (n and percentage (% of classified information were statistically described, and the comparison between groups (i.e., current students vs. research staff was performed using chi-square test.A total of 298 questionnaires were distributed, and 272 responses were received, which included 266 valid questionnaires (from 118 current students and 148 research staff. Among the 266 survey participants, only 15.8% was aware of the SYRCLE's risk of bias tool, with significant difference between the two groups (P = 0.003, and the awareness rates of ARRIVE guidelines and GSPC were only 9.4% and 9.0%, respectively; 58.6% survey participants believed that the reports of animal experimental studies in Chinese literature were inadequate, with significant difference between the two groups (P = 0.004. In addition, only approximately 1/3 of the survey participants had read systematic reviews and meta-analysis reports of animal experimental studies; only 16/266 (6.0% had carried out/participated in and 11/266 (4.1% had published systematic reviews/meta-analysis of animal experimental studies.The awareness and use rates of SYRCLE's risk-of-bias tool, the ARRIVE guidelines, and the GSPC were low among Chinese basic medical researchers. Therefore

Calibration guidelines for surface texture instruments - horizontal axis

DEFF Research Database (Denmark)

Andreasen, Jan Lasson; Shem, R. Krüger

The present report is a documentation of the work carried out at DTU, on TASK 5.1: PROCEDURES FOR CALIBRATION IN X- AND Y- DIRECTION the project with contract SMT4-CT97-2176 with title: Calibration Standards for Surface Topography Measuring Systems down to Nanometric Scale. After a short introduc......The present report is a documentation of the work carried out at DTU, on TASK 5.1: PROCEDURES FOR CALIBRATION IN X- AND Y- DIRECTION the project with contract SMT4-CT97-2176 with title: Calibration Standards for Surface Topography Measuring Systems down to Nanometric Scale. After a short...

Updated Design Standards and Guidance from the What Works Clearinghouse: Regression Discontinuity Designs and Cluster Designs

Science.gov (United States)

Cole, Russell; Deke, John; Seftor, Neil

2016-01-01

The What Works Clearinghouse (WWC) maintains design standards to identify rigorous, internally valid education research. As education researchers advance new methodologies, the WWC must revise its standards to include an assessment of the new designs. Recently, the WWC has revised standards for two emerging study designs: regression discontinuity…

Social work in a society under pressure. Keeping professional principles and standards upright.

Directory of Open Access Journals (Sweden)

Willem Blok

2016-06-01

Full Text Available This article is based on the content and outcome of the 5th Annual International Conference on Social Work & Social Work Education in Leeuwarden, The Netherlands on February 5, 2016. It shows how Social Work is embedded in society, and describes the pressure of contemporary (international problems on society, and the way in which authorities respond to it. The article continues with a discussion of the answers given by the 200 conference participants on the question how social workers and social work educators could cope with this pressure without denying their international professional principles and standards.

Experimentally obtained values of electric field of an atmospheric pressure plasma jet impinging on a dielectric surface

NARCIS (Netherlands)

Sobota, A.; Guaitella, O.; Garcia-Caurel, E.

2013-01-01

We report on experimentally obtained values of the electric field magnitude on a dielectric surface induced by an impinging atmospheric pressure plasma jet. The plasma plume was striking the dielectric surface at an angle of 45¿, at 5mm from the surface measured at the axis of the jet. The results

Interaction between an elastic structure and free-surface flows: experimental versus numerical comparisons using the PFEM

Science.gov (United States)

Idelsohn, S. R.; Marti, J.; Souto-Iglesias, A.; Oñate, E.

2008-12-01

The paper aims to introduce new fluid structure interaction (FSI) tests to compare experimental results with numerical ones. The examples have been chosen for a particular case for which experimental results are not much reported. This is the case of FSI including free surface flows. The possibilities of the Particle Finite Element Method (PFEM) [1] for the simulation of free surface flows is also tested. The simulations are run using the same scale as the experiment in order to minimize errors due to scale effects. Different scenarios are simulated by changing the boundary conditions for reproducing flows with the desired characteristics. Details of the input data for all the examples studied are given. The aim is to identifying benchmark problems for FSI including free surface flows for future comparisons between different numerical approaches.

Adsorption of nitrogen on W(100): effect of surface disorder on the work function change

International Nuclear Information System (INIS)

Singh-Bofarai, S.P.; King, D.A.

1976-01-01

At room temperature nitrogen adsorption causes the work function of the (100) plane of tungsten to decrease by approximately 0.6 eV, while on all other planes the work function is increased, albeit by as little as 0.03 eV on the (110) plane. Surface disorder can readily be created by the vapour deposition of W onto a clean, annealed W single crystal surface, and in the present work this technique was used to shadow a W field emission tip with disordered W atoms so as to observe the effect of surface disorder on the work function change due to nitrogen adsorption, particularly at the (100) poles of the tip. (Auth.)

40 CFR Table 36 to Subpart Uuu of... - Work Practice Standards for HAP Emissions From Bypass Lines

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Work Practice Standards for HAP Emissions From Bypass Lines 36 Table 36 to Subpart UUU of Part 63 Protection of Environment ENVIRONMENTAL..., Table 36 Table 36 to Subpart UUU of Part 63—Work Practice Standards for HAP Emissions From Bypass Lines...

Experimental studies of surface modified oscillating heat pipes

Science.gov (United States)

Leu, Tzong-Shyng; Wu, Cheng-Han

2017-11-01

Oscillating heat pipe (OHP) is a two-phase heat transfer device which has the characteristics of simple construction, high heat flux capability and no need of wicking structures for liquid transport. There are many studies in finding the ways how to improve the system performance OHP. In this paper, studies of the effects of contact angle ( θ c ) on the inner wall of OHP system have been conducted first. Glass OHP systems with unmodified ( θ c = 26.74°), superhydrophobic ( θ c = 156.2°), superhydrophilic ( θ c evaporator region and superhydrophobic within condensation region) surfaces, are studied. The research results indicated that thermal resistance of these four OHP systems can be significantly affected by different surface modification approaches. Although superhydrophobic OHP system can still work, the thermal resistance ( R th ) is the highest one of the four OHP systems, R th = 0.36 °C/W at 200 W. Unmodified pure glass and superhydrophilic OHP systems have similar performance. Thermal resistances are 0.28 and 0.27 °C/W at 200 W respectively. The hybrid OHP achieves the lowest thermal resistance, R th = 0.23 °C/W at 200 W in this study. The exact mechanism and effects of contact angle on OHP systems are investigated with the help of flow visualization. By comparing the flow visualization results of OHP systems before and after surface modification, one tries to find the mechanism how the surface modified inner wall surface affects the OHP system performance. In additional to the reason that the superhydrophobic dropwise condensation surface inside the hybrid OHP system, hybrid OHP system shows more stable and energetic circulation flow. It is found that instead of stratified flow, vapor slug flows are identified within the evaporator section of the hybrid OHP system that can effectively generate higher pressure force for two phase interfacial flow. This effect is attributed to be the main mechanism for better performance of the hybrid OHP system.

Entropic and Electrostatic Effects on the Folding Free Energy of a Surface-Attached Biomolecule: An Experimental and Theoretical Study

Science.gov (United States)

Watkins, Herschel M.; Vallée-Bélisle, Alexis; Ricci, Francesco; Makarov, Dmitrii E.; Plaxco, Kevin W.

2012-01-01

Surface-tethered biomolecules play key roles in many biological processes and biotechnologies. However, while the physical consequences of such surface attachment have seen significant theoretical study, to date this issue has seen relatively little experimental investigation. In response we present here a quantitative experimental and theoretical study of the extent to which attachment to a charged –but otherwise apparently inert– surface alters the folding free energy of a simple biomolecule. Specifically, we have measured the folding free energy of a DNA stem loop both in solution and when site-specifically attached to a negatively charged, hydroxyl-alkane-coated gold surface. We find that, whereas surface attachment is destabilizing at low ionic strength it becomes stabilizing at ionic strengths above ~130 mM. This behavior presumably reflects two competing mechanisms: excluded volume effects, which stabilize the folded conformation by reducing the entropy of the unfolded state, and electrostatics, which, at lower ionic strengths, destabilizes the more compact folded state via repulsion from the negatively charged surface. To test this hypothesis we have employed existing theories of the electrostatics of surface-bound polyelectrolytes and the entropy of surface-bound polymers to model both effects. Despite lacking any fitted parameters, these theoretical models quantitatively fit our experimental results, suggesting that, for this system, current knowledge of both surface electrostatics and excluded volume effects is reasonably complete and accurate. PMID:22239220

Fast and cheap prototyping of non-standard optical components for sensing speckle dynamics

DEFF Research Database (Denmark)

Jakobsen, Michael Linde; Olesen, Anders Sig; Stubager, Jørgen

2016-01-01

As a part of the work carried out a project supported by the Danish council for technology and innovation, we have investigated the option of smoothening standard CNC machined surfaces. In the process of constructing optical prototypes, involving custom-designed optics, the development price...... and time can become a prohibitively large part of a research budget. Machining the optical surfaces of a molding tool may be done directly using diamond turning, but it is expensive and time consuming. Alternatively, a more standardized and cheaper machining method can be used, however, calling for manual...... surfaces of various shapes succeeding a standard CNC machining process. Different coatings have been tested for their abilities to fill and smoothen out structures of larger scales, while removing the small-scale roughness, which is critical for optical uses. In this work we will present an optical element...

Joint surface modeling with thin-plate splines.

Science.gov (United States)

Boyd, S K; Ronsky, J L; Lichti, D D; Salkauskas, K; Chapman, M A; Salkauskas, D

1999-10-01

Mathematical joint surface models based on experimentally determined data points can be used to investigate joint characteristics such as curvature, congruency, cartilage thickness, joint contact areas, as well as to provide geometric information well suited for finite element analysis. Commonly, surface modeling methods are based on B-splines, which involve tensor products. These methods have had success; however, they are limited due to the complex organizational aspect of working with surface patches, and modeling unordered, scattered experimental data points. An alternative method for mathematical joint surface modeling is presented based on the thin-plate spline (TPS). It has the advantage that it does not involve surface patches, and can model scattered data points without experimental data preparation. An analytical surface was developed and modeled with the TPS to quantify its interpolating and smoothing characteristics. Some limitations of the TPS include discontinuity of curvature at exactly the experimental surface data points, and numerical problems dealing with data sets in excess of 2000 points. However, suggestions for overcoming these limitations are presented. Testing the TPS with real experimental data, the patellofemoral joint of a cat was measured with multistation digital photogrammetry and modeled using the TPS to determine cartilage thicknesses and surface curvature. The cartilage thickness distribution ranged between 100 to 550 microns on the patella, and 100 to 300 microns on the femur. It was found that the TPS was an effective tool for modeling joint surfaces because no preparation of the experimental data points was necessary, and the resulting unique function representing the entire surface does not involve surface patches. A detailed algorithm is presented for implementation of the TPS.

Human experimental pain models: A review of standardized methods in drug development

Directory of Open Access Journals (Sweden)

K. Sunil kumar Reddy

2012-01-01

Full Text Available Human experimental pain models are essential in understanding the pain mechanisms and appear to be ideally suited to test analgesic compounds. The challenge that confronts both the clinician and the scientist is to match specific treatments to different pain-generating mechanisms and hence reach a pain treatment tailored to each individual patient. Experimental pain models offer the possibility to explore the pain system under controlled settings. Standardized stimuli of different modalities (i.e., mechanical, thermal, electrical, or chemical can be applied to the skin, muscles, and viscera for a differentiated and comprehensive assessment of various pain pathways and mechanisms. Using a multimodel-multistructure testing, the nociception arising from different body structures can be explored and modulation of specific biomarkers by new and existing analgesic drugs can be profiled. The value of human experimental pain models is to link animal and clinical pain studies, providing new possibilities for designing successful clinical trials. Spontaneous pain, the main compliant of the neuropathic patients, but currently there is no human model available that would mimic chronic pain. Therefore, current human pain models cannot replace patient studies for studying efficacy of analgesic compounds, although being helpful for proof-of-concept studies and dose finding.

Uncertainty Estimates: A New Editorial Standard

International Nuclear Information System (INIS)

Drake, Gordon W.F.

2014-01-01

Full text: The objective of achieving higher standards for uncertainty estimates in the publication of theoretical data for atoms and molecules requires a concerted effort by both the authors of papers and the editors who send them out for peer review. In April, 2011, the editors of Physical Review A published an Editorial announcing a new standard that uncertainty estimates would be required whenever practicable, and in particular in the following circumstances: 1. If the authors claim high accuracy, or improvements on the accuracy of previous work. 2. If the primary motivation for the paper is to make comparisons with present or future high precision experimental measurements. 3. If the primary motivation is to provide interpolations or extrapolations of known experimental measurements. The new policy means that papers that do not meet these standards are not sent out for peer review until they have been suitably revised, and the authors are so notified immediately upon receipt. The policy has now been in effect for three years. (author

Experimental determination of effective surface area and conductivities in the porous anode of molten carbonate fuel cell

Energy Technology Data Exchange (ETDEWEB)

Yoshikawa, M.; Boden, A.; Sparr, M.; Lindbergh, G. [Central Research Institute for Electric Power Industry, Kanagawa (Japan)

2006-07-14

Stationary polarization curves and electrochemical impedance spectroscopy of a porous nickel anode in a molten carbonate fuel cell were obtained in order to determine the active surface area and conductivities with varying degree of electrolyte filling for two anode feed-gas compositions, one simulating operation with steam reformed natural gas and the other one gasified coal. The active surface area for coal gas is reduced by around 70-80% compared to the standard gas composition in the case of Li/Na carbonate. Moreover, an optimal degree of electrolyte filling was shifted toward higher filling degree in the case of operation with coal gas. In order to evaluate the experimental data a one-dimensional model was used. The reaction rate at the matrix/electrode interface is about five times higher than the average reaction rate in the whole electrode in case of 10% electrolyte filling. This result suggests that the lower limit of the filling degree of the anode should be around 15% in order to avoid non-uniform distribution of the reaction in the electrode. Therefore, in the case of applying Li/Na carbonate in the MCFC, an electrolyte distribution model taking into account the wetting properties of the electrode is required in order to set an optimal electrolyte filling degree in the electrode.

Evaluation of the Quebec Healthy Enterprise Standard: Effect on Adverse Psychosocial Work Factors and Psychological Distress.

Science.gov (United States)

Letellier, Marie-Claude; Duchaine, Caroline S; Aubé, Karine; Talbot, Denis; Mantha-Bélisle, Marie-Michèle; Sultan-Taïeb, Hélène; St-Hilaire, France; Biron, Caroline; Vézina, Michel; Brisson, Chantal

2018-02-28

Adverse psychosocial work factors are recognized as a significant source of psychological distress, resulting in a considerable socioeconomic burden. The impact of occupational health standards that aim to reduce these adverse work factors, such as the Quebec Healthy Enterprise Standard (QHES), is of great interest for public health. The aim of this study was to evaluate, for the first time, the effect of QHES interventions targeting adverse psychosocial work factors on the prevalence of these factors and of psychological distress among ten Quebec organizations. These outcomes were assessed by questionnaire using validated instruments before (T1, n = 2849) and 2-3 years following (T2, n = 2560) QHES implementation. Beneficial effects of interventions were observed for two adverse psychosocial work factors: low rewards (ratio of prevalence ratios (PRs) = 0.77, 95% CI = 0.66-0.91) and low social support at work (ratio of PRs = 0.89, 95% CI = 0.77-1.03). Moreover, beneficial effects of interventions were also observed on the prevalence of high psychological distress (ratio of PRs = 0.86, 95% CI = 0.75-0.998). Psychosocial interventions implemented in the context of this standard improved the psychosocial work environment and had beneficial effects on workers' mental health.

Evaluation of the Quebec Healthy Enterprise Standard: Effect on Adverse Psychosocial Work Factors and Psychological Distress

Directory of Open Access Journals (Sweden)

Marie-Claude Letellier

2018-02-01

Full Text Available Adverse psychosocial work factors are recognized as a significant source of psychological distress, resulting in a considerable socioeconomic burden. The impact of occupational health standards that aim to reduce these adverse work factors, such as the Quebec Healthy Enterprise Standard (QHES, is of great interest for public health. The aim of this study was to evaluate, for the first time, the effect of QHES interventions targeting adverse psychosocial work factors on the prevalence of these factors and of psychological distress among ten Quebec organizations. These outcomes were assessed by questionnaire using validated instruments before (T1, n = 2849 and 2–3 years following (T2, n = 2560 QHES implementation. Beneficial effects of interventions were observed for two adverse psychosocial work factors: low rewards (ratio of prevalence ratios (PRs = 0.77, 95% CI = 0.66–0.91 and low social support at work (ratio of PRs = 0.89, 95% CI = 0.77–1.03. Moreover, beneficial effects of interventions were also observed on the prevalence of high psychological distress (ratio of PRs = 0.86, 95% CI = 0.75–0.998. Psychosocial interventions implemented in the context of this standard improved the psychosocial work environment and had beneficial effects on workers’ mental health.

Experimental investigation on carbon nano tubes coated brass rectangular extended surfaces

International Nuclear Information System (INIS)

Senthilkumar, Rajendran; Prabhu, Sethuramalingam; Cheralathan, Marimuthu

2013-01-01

Finned surface has been extensively used for free convection cooling of internal combustion engines and several electronic kits etc. Here rectangular brass fin was preferred for analysis. Thermocouples were attached all over the surface of the fin in equal distances. The measurement of surface temperature and calculated convective heat transfer rate were reported for several heat input values. The overall system performance can be improved by enhancing heat transfer rate of extended surfaces. Based on the above requirement, brass surface was coated by carbon nano tubes. The temperature and heat transfer characteristics were investigated using Taguchi method for experimental design. Finally the performances of coated and non-coated rectangular brass fins were compared. The average percentage of increase in heat transfer rate was proved around 12% for carbon nanocoated rectangular brass fins. - Graphical abstract: The designed Natural and Forced convection Heat Transfer Test Rig measures the enhanced rate of heat transfer for nano coated rectangular fins than in non-coated fins. Highlights: ► Rectangular brass fins were preferred for convective heat transfer process. ► The rectangular brass fins are coated with multi wall carbon nano tubes in EBPVD process with nanometer thickness. ► Temperature and heat transfer rate were investigated for nanocoated and non-coated fins by using Taguchi method. ► Multi wall carbon nanotubes act as a pin fin to enhance surface area for effective convective heat transfer rate.

Guidelines for Home Energy Upgrade Professionals: Standard Work Specifications for Multifamily Energy Upgrades (Fact Sheet)

Energy Technology Data Exchange (ETDEWEB)

2011-08-01

This fact sheet provides essential information about the 2011 publication of the Workforce Guidelines for Multifamily Home Energy Upgrades, including their origin, their development with the help of industry leaders to create the standard work specifications for retrofit work.

The Application and Its Consequences for Non-Standard Knowledge Work

DEFF Research Database (Denmark)

Nouwens, Midas; Klokmose, Clemens Nylandsted

2018-01-01

Application-centric computing dominates human-computer interactions, yet the concept of an application is ambiguous and the impact of its ubiquity underexplored. We unpack “the application” through the lens of non-standard knowledge work: freelance, self-employed, and fixed-term contract workers...... of applications, such as update processes, interface symmetries, application-document relationships, and operating system and hardware dependencies. By empirically and analytically focusing on “the application”, we reveal the implications of the current application-centric computing paradigm and discuss how...

The Future of Geospatial Standards

Science.gov (United States)

Bermudez, L. E.; Simonis, I.

2016-12-01

The OGC is an international not-for-profit standards development organization (SDO) committed to making quality standards for the geospatial community. A community of more than 500 member organizations with more than 6,000 people registered at the OGC communication platform drives the development of standards that are freely available for anyone to use and to improve sharing of the world's geospatial data. OGC standards are applied in a variety of application domains including Environment, Defense and Intelligence, Smart Cities, Aviation, Disaster Management, Agriculture, Business Development and Decision Support, and Meteorology. Profiles help to apply information models to different communities, thus adapting to particular needs of that community while ensuring interoperability by using common base models and appropriate support services. Other standards address orthogonal aspects such as handling of Big Data, Crowd-sourced information, Geosemantics, or container for offline data usage. Like most SDOs, the OGC develops and maintains standards through a formal consensus process under the OGC Standards Program (OGC-SP) wherein requirements and use cases are discussed in forums generally open to the public (Domain Working Groups, or DWGs), and Standards Working Groups (SWGs) are established to create standards. However, OGC is unique among SDOs in that it also operates the OGC Interoperability Program (OGC-IP) to provide real-world testing of existing and proposed standards. The OGC-IP is considered the experimental playground, where new technologies are researched and developed in a user-driven process. Its goal is to prototype, test, demonstrate, and promote OGC Standards in a structured environment. Results from the OGC-IP often become requirements for new OGC standards or identify deficiencies in existing OGC standards that can be addressed. This presentation will provide an analysis of the work advanced in the OGC consortium including standards and testbeds

Working group 1B - basis for the standard-liquid pathway

International Nuclear Information System (INIS)

Budnitz, R.

1993-01-01

This paper presents a summary of the progress made by working group 1B (Basis for the Standard-Liquid Pathway) during the Electric Power Research Institute's EPRI Workshop on the technical basis of EPA HLW Disposal Criteria, March 1993. This group discussed the containment requirements of Environmental Protection Agency (EPA) standard 40 CFR Part 191. This is a major issue when considering the liquid pathway of contamination during the disposal of high-level radioactive wastes. Questions that were raised by this group were (1) What were the problems with Table 1 of 40 CFR Part 191?; (2) What would be fixed with the person-rem alternative that is offered?; and (3) What would be fixed if Table 1 were supplemented with additional columns for other pathways? Other topics that were touched on were the definition of the term open-quotes reasonable expectationsclose quotes and 100,000 year criteria

Microscopic work function anisotropy and surface chemistry of 316L stainless steel using photoelectron emission microscopy

Energy Technology Data Exchange (ETDEWEB)

Barrett, N., E-mail: nick.barrett@cea.fr [CEA, IRAMIS, SPEC, LENSIS, F-91191 Gif-sur-Yvette (France); Renault, O. [CEA, LETI, Minatec Campus, F-38054 Grenoble Cedex 09 (France); Lemaître, H. [Université de Cergy-Pontoise, Rue d’Eragny, Neuville sur Oise, 95 031 Cergy-Pontoise (France); Surface Dynamics Laboratory, Institut for Fysik og Astronomi Aarhus Universitet, Ny Munkegade 120, 8000 Aarhus C (Denmark); Bonnaillie, P. [CEA, DEN, DANS, DMN, SRMP, F-91191 Gif-sur-Yvette (France); Barcelo, F. [CEA, DEN, DANS, DMN, SRMA, LA2M, F-91191 Gif-sur-Yvette (France); Miserque, F. [CEA, DEN, DANS, DPC, SCCME, LECA, F-91191 Gif-sur-Yvette (France); Wang, M.; Corbel, C. [Laboratoire des Solides Irradis, Ecole Polytechnique, route de Saclay, F-91128 Palaiseau (France)

2014-08-15

Highlights: • PEEM and EBSD study of spatial variations in local work function of 316L steel. • Correlation between work function and crystal grain orientation at the surface of 316L steel. • Spatially resolved chemistry of residual oxide layer. - Abstract: We have studied the variation in the work function of the surface of sputtered cleaned 316L stainless steel with only a very thin residual oxide surface layer as a function of grain orientation using X-ray photoelectron emission microscopy (XPEEM) and Electron Backscattering Diffraction. The grains are mainly oriented [1 1 1] and [1 0 1]. Four distinct work function values spanning a 150 meV energy window are measured. Grains oriented [1 1 1] have a higher work function than those oriented [1 0 1]. From core level XPEEM we deduce that all grain surfaces are Cr enriched and Ni depleted whereas the Cr/Fe ratio is similar for all grains. The [1 1 1] oriented grains show evidence for a Cr{sub 2}O{sub 3} surface oxide and a higher concentration of defective oxygen sites.

Field and laboratory emission cell automation and control system for investigating surface chemistry reactions

Science.gov (United States)

Flemmer, Michael M.; Ham, Jason E.; Wells, J. R.

2007-01-01

A novel system [field and laboratory emission cell (FLEC) automation and control system] has been developed to deliver ozone to a surface utilizing the FLEC to simulate indoor surface chemistry. Ozone, humidity, and air flow rate to the surface were continuously monitored using an ultraviolet ozone monitor, humidity, and flow sensors. Data from these sensors were used as feedback for system control to maintain predetermined experimental parameters. The system was used to investigate the chemistry of ozone with α-terpineol on a vinyl surface over 72h. Keeping all other experimental parameters the same, volatile organic compound emissions from the vinyl tile with α-terpineol were collected from both zero and 100ppb(partsper109) ozone exposures. System stability profiles collected from sensor data indicated experimental parameters were maintained to within a few percent of initial settings. Ozone data from eight experiments at 100ppb (over 339h) provided a pooled standard deviation of 1.65ppb and a 95% tolerance of 3.3ppb. Humidity data from 17 experiments at 50% relative humidity (over 664h) provided a pooled standard deviation of 1.38% and a 95% tolerance of 2.77%. Data of the flow rate of air flowing through the FLEC from 14 experiments at 300ml/min (over 548h) provided a pooled standard deviation of 3.02ml/min and a 95% tolerance range of 6.03ml/min. Initial experimental results yielded long term emissions of ozone/α-terpineol reaction products, suggesting that surface chemistry could play an important role in indoor environments.

Experimental and computational studies of positron-stimulated ion desorption from TiO2(1 1 0) surface

Science.gov (United States)

Yamashita, T.; Hagiwara, S.; Tachibana, T.; Watanabe, K.; Nagashima, Y.

2017-11-01

Experimental and computational studies of the positron-stimulated O+ ion desorption process from a TiO2(1 1 0) surface are reported. The measured data indicate that the O+ ion yields depend on the positron incident energy in the energy range between 0.5 keV and 15 keV. This dependence is closely related to the fraction of positrons which diffuse back to the surface after thermalization in the bulk. Based on the experimental and computational results, we conclude that the ion desorption via positron-stimulation occurs dominantly by the annihilation of surface-trapped positrons with core electrons of the topmost surface atoms.

Experimental Investigation of Space Radiation Processing in Lunar Soil Ilmenite: Combining Perspectives from Surface Science and Transmission Electron Microscopy

Science.gov (United States)

Christoffersen, R.; Keller, L. P.; Rahman, Z.; Baragiola, R.

2010-01-01

Energetic ions mostly from the solar wind play a major role in lunar space weathering because they contribute structural and chemical changes to the space-exposed surfaces of lunar regolith grains. In mature mare soils, ilmenite (FeTiO3) grains in the finest size fraction have been shown in transmission electron microscope (TEM) studies to exhibit key differences in their response to space radiation processing relative to silicates [1,2,3]. In ilmenite, solar ion radiation alters host grain outer margins to produce 10-100 nm thick layers that are microstructurally complex, but dominantly crystalline compared to the amorphous radiation-processed rims on silicates [1,2,3]. Spatially well-resolved analytical TEM measurements also show nm-scale compositional and chemical state changes in these layers [1,3]. These include shifts in Fe/Ti ratio from strong surface Fe-enrichment (Fe/Ti >> 1), to Fe depletion (Fe/Ti < 1) at 40-50 nm below the grain surface [1,3]. These compositional changes are not observed in the radiation-processed rims on silicates [4]. Several mechanism(s) to explain the overall relations in the ilmenite grain rims by radiation processing and/or additional space weathering processes were proposed by [1], and remain under current consideration [3]. A key issue has concerned the ability of ion radiation processing alone to produce some of the deeper- penetrating compositional changes. In order to provide some experimental constraints on these questions, we have performed a combined X-ray photoelectron spectroscopy (XPS) and field-emission scanning transmission electron (FE-STEM) study of experimentally ion-irradiated ilmenite. A key feature of this work is the combination of analytical techniques sensitive to changes in the irradiated samples at depth scales going from the immediate surface (approx.5 nm; XPS), to deeper in the grain interior (5-100 nm; FE-STEM).

30 CFR 77.103 - Electrical work; qualified person.

Science.gov (United States)

2010-07-01

... Section 77.103 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS, SURFACE COAL MINES AND SURFACE WORK AREAS OF UNDERGROUND... Health Districts at regular intervals, or as demand requires. (d) A score of at least 80 percent on each...

Etalon (standard) for surface potential distribution produced by electric activity of the heart.

Science.gov (United States)

Szathmáry, V; Ruttkay-Nedecký, I

1981-01-01

The authors submit etalon (standard) equipotential maps as an aid in the evaluation of maps of surface potential distributions in living subjects. They were obtained by measuring potentials on the surface of an electrolytic tank shaped like the thorax. The individual etalon maps were determined in such a way that the parameters of the physical dipole forming the source of the electric field in the tank corresponded to the mean vectorcardiographic parameters measured in a healthy population sample. The technique also allows a quantitative estimate of the degree of non-dipolarity of the heart as the source of the electric field.

[Comparison of surface light scattering of acrylic intraocular lenses made by lathe-cutting and cast-molding methods--long-term observation and experimental study].

Science.gov (United States)

Nishihara, Hitoshi; Ayaki, Masahiko; Watanabe, Tomiko; Ohnishi, Takeo; Kageyama, Toshiyuki; Yaguchi, Shigeo

2004-03-01

To compare the long-term clinical and experimental results of soft acrylic intraocular lenses(IOLs) manufactured by the lathe-cut(LC) method and by the cast-molding(CM) method. This was a retrospective study of 20 patients(22 eyes) who were examined in a 5- and 7-year follow-up study. Sixteen eyes were implanted with polyacrylic IOLs manufactured by the LC method and 6 eyes were implanted with polyacrylic IOLs manufactured by the CM method. Postoperative measurements included best corrected visual acuity, contrast sensitivity, biomicroscopic examination, and Scheimpflug slit-lamp images to evaluate surface light scattering. Scanning electron microscopy and three-dimensional surface analysis were conducted. At 7 years, the mean visual acuity was 1.08 +/- 0.24 (mean +/- standard deviation) in the LC group and 1.22 +/- 0.27 in the CM group. Surface light-seatter was 12.0 +/- 4.0 computer compatible tapes(CCT) in the LC group and 37.4 +/- 5.4 CCT in the CM group. Mean surface roughness was 0.70 +/- 0.07 nm in the LC group and 6.16 +/- 0.97 nm in the CM group. Acrylic IOLs manufactured by the LC method are more stable in long-termuse.

A heat transport benchmark problem for predicting the impact of measurements on experimental facility design

International Nuclear Information System (INIS)

Cacuci, Dan Gabriel

2016-01-01

the test-section benchmark, it is shown that the maximum coolant and rod surface temperatures responses are the most important measurable quantities. Using all of the available information, the PM_CMPS formulas yield optimally predicted best-estimate nominal model parameter values and reduced predicted standard deviations for the predicted parameters, such that: (i) the model parameters displaying the largest relative sensitivities and largest relative standard deviations are affected the most; and (ii) the model parameters with zero sensitivities remain unaffected by applying the PM_CMPS methodology. The PM_CMPS formulas also yield optimally predicted best-estimate nominal values for the model responses, along with correspondingly reduced predicted standard deviations. Assimilating within the PM_CMPS methodology an accurate measurement of the benchmark's maximum coolant temperature has the following impacts on the quantity that has been measured (i.e., on the maximum coolant temperature): (i) the nominal value of the predicted maximum coolant temperature is closer to the more “accurate” experimental value; (ii) the originally computed standard deviation is decreased significantly. In addition, the measurement of the maximum coolant temperature impacts not only the quantity being measured, but also impacts the other responses of interest, e.g., the maximum temperature in the rod and the maximum rod surface temperature. In all cases, the predicted standard deviations were decreased substantially, indicating that the predicted values are more accurate than the originally computed ones. The PM_CMPS formulas were also used to predict the impact of the simultaneous assimilation of the maximum coolant and the maximum rod's surface temperature measurements. As expected in view of the fact that the PM_CMPS methodology uses Bayes’ theorem to combine information, the assimilation of two accurate experiments reduces the predicted standard deviations of the

Electron microscopy of surfaces

International Nuclear Information System (INIS)

Venables, J.A.

1981-01-01

Electron beam techniques used to study clean surfaces and surface processes on a microscopic scale are reviewed. Recent experimental examples and possible future developments are discussed. Special emphasis is given to (i) transmission diffraction and microscopy techniques, including atomic imaging; (ii) Auger microscopy on bulk and thin film samples; (iii) secondary electron microscopy, especially low energy secondaries for work-function imaging and photoelectron imaging; and (iv) reflection electron microscopy and diffraction. (orig.)

Work Scope for Developing Standards for Emergency Preparedness and Response: Fiscal Year 2004 Final Report

Energy Technology Data Exchange (ETDEWEB)

Stenner, Robert D.

2005-09-28

Summarizes the fiscal year 2004 work completed on PNNL's Department of Homeland Security Emergency Preparedness and Response Standards Development Project. Also, the report includes key draft standards, in various stages of development and publication, that were associated with various tasks of the fiscal year 2004 scope of the project.

The Standard, Power, and Color Model of Instrument Combination in Romantic-Era Symphonic Works

Directory of Open Access Journals (Sweden)

Randolph Johnson

2011-08-01

Full Text Available The Standard, Power, and Color (SPC model describes the nexus between musical instrument combination patterns and expressive goals in music. Instruments within each SPC group tend to attract each other and work as a functional unit to create orchestral gestures. Standard instruments establish a timbral groundwork; Power instruments create contrast through loud dynamic climaxes; and Color instruments catch listeners’ attention by means of their sparing use. Examples within these three groups include violin (Standard, piccolo (Power, and harp (Color. The SPC theory emerges from analyses of nineteenth-century symphonic works. Multidimensional scaling analysis of instrument combination frequencies maps instrument relationships; hierarchical clustering analysis indicates three SPC groups within the map. The SPC characterization is found to be moderately robust through the results of hypothesis testing: (1 Color instruments are included less often in symphonic works; (2 when Color instruments are included, they perform less often than the average instrument; and (3 Color and non-Color instruments have equal numbers of solo occurrences. Additionally, (4 Power instruments are positively associated with louder dynamic levels; and (5 when Power instruments are present in the musical texture, the pitch range spanned by the entire orchestra does not become more extreme.

Progress Report on the Airborne Composition Standard Variable Name and Time Series Working Groups of the 2017 ESDSWG

Science.gov (United States)

Evans, K. D.; Early, A. B.; Northup, E. A.; Ames, D. P.; Teng, W. L.; Olding, S. W.; Krotkov, N. A.; Arctur, D. K.; Beach, A. L., III; Silverman, M. L.

2017-12-01

The role of NASA's Earth Science Data Systems Working Groups (ESDSWG) is to make recommendations relevant to NASA's Earth science data systems from users' experiences and community insight. Each group works independently, focusing on a unique topic. Progress of two of the 2017 Working Groups will be presented. In a single airborne field campaign, there can be several different instruments and techniques that measure the same parameter on one or more aircraft platforms. Many of these same parameters are measured during different airborne campaigns using similar or different instruments and techniques. The Airborne Composition Standard Variable Name Working Group is working to create a list of variable standard names that can be used across all airborne field campaigns in order to assist in the transition to the ICARTT Version 2.0 file format. The overall goal is to enhance the usability of ICARTT files and the search ability of airborne field campaign data. The Time Series Working Group (TSWG) is a continuation of the 2015 and 2016 Time Series Working Groups. In 2015, we started TSWG with the intention of exploring the new OGC (Open Geospatial Consortium) WaterML 2 standards as a means for encoding point-based time series data from NASA satellites. In this working group, we realized that WaterML 2 might not be the best solution for this type of data, for a number of reasons. Our discussion with experts from other agencies, who have worked on similar issues, identified several challenges that we would need to address. As a result, we made the recommendation to study the new TimeseriesML 1.0 standard of OGC as a potential NASA time series standard. The 2016 TSWG examined closely the TimeseriesML 1.0 and, in coordination with the OGC TimeseriesML Standards Working Group, identified certain gaps in TimeseriesML 1.0 that would need to be addressed for the standard to be applicable to NASA time series data. An engineering report was drafted based on the OGC Engineering

The importance of accurate adiabatic interaction potentials for the correct description of electronically nonadiabatic vibrational energy transfer: A combined experimental and theoretical study of NO(v = 3) collisions with a Au(111) surface

Energy Technology Data Exchange (ETDEWEB)

Golibrzuch, Kai; Shirhatti, Pranav R.; Kandratsenka, Alexander; Wodtke, Alec M.; Bartels, Christof [Institute for Physical Chemistry, Georg August University of Göttingen, Göttingen 37077 (Germany); Max Planck Institute for Biophysical Chemistry, Göttingen 37077 (Germany); Rahinov, Igor [Department of Natural Sciences, The Open University of Israel, Ra' anana 4353701 (Israel); Auerbach, Daniel J. [Institute for Physical Chemistry, Georg August University of Göttingen, Göttingen 37077 (Germany); Max Planck Institute for Biophysical Chemistry, Göttingen 37077 (Germany); Department of Chemistry and Biochemistry, University of California Santa Barbara, Santa Barbara, California 93106 (United States)

2014-01-28

We present a combined experimental and theoretical study of NO(v = 3 → 3, 2, 1) scattering from a Au(111) surface at incidence translational energies ranging from 0.1 to 1.2 eV. Experimentally, molecular beam–surface scattering is combined with vibrational overtone pumping and quantum-state selective detection of the recoiling molecules. Theoretically, we employ a recently developed first-principles approach, which employs an Independent Electron Surface Hopping (IESH) algorithm to model the nonadiabatic dynamics on a Newns-Anderson Hamiltonian derived from density functional theory. This approach has been successful when compared to previously reported NO/Au scattering data. The experiments presented here show that vibrational relaxation probabilities increase with incidence energy of translation. The theoretical simulations incorrectly predict high relaxation probabilities at low incidence translational energy. We show that this behavior originates from trajectories exhibiting multiple bounces at the surface, associated with deeper penetration and favored (N-down) molecular orientation, resulting in a higher average number of electronic hops and thus stronger vibrational relaxation. The experimentally observed narrow angular distributions suggest that mainly single-bounce collisions are important. Restricting the simulations by selecting only single-bounce trajectories improves agreement with experiment. The multiple bounce artifacts discovered in this work are also present in simulations employing electronic friction and even for electronically adiabatic simulations, meaning they are not a direct result of the IESH algorithm. This work demonstrates how even subtle errors in the adiabatic interaction potential, especially those that influence the interaction time of the molecule with the surface, can lead to an incorrect description of electronically nonadiabatic vibrational energy transfer in molecule-surface collisions.

Preclinical electrogastrography in experimental pigs

Science.gov (United States)

Květina, Jaroslav; Varayil, Jithinraj Edakkanambeth; Ali, Shahzad Marghoob; Kuneš, Martin; Bureš, Jan; Tachecí, Ilja; Rejchrt, Stanislav; Kopáčová, Marcela

2010-01-01

Surface electrogastrography (EGG) is a non-invasive means of recording gastric myoelectric activity or slow waves from cutaneous leads placed over the stomach. This paper provides a comprehensive review of preclinical EGG. Our group recently set up and worked out the methods for EGG in experimental pigs. We gained our initial experience in the use of EGG in assessment of porcine gastric myoelectric activity after volume challenge and after intragastric administration of itopride and erythromycin. The mean dominant frequency in pigs is comparable with that found in humans. EGG in experimental pigs is feasible. Experimental EGG is an important basis for further preclinical projects in pharmacology and toxicology. PMID:21217873

Plasma treatment of bulk niobium surface for superconducting rf cavities: Optimization of the experimental conditions on flat samples

Directory of Open Access Journals (Sweden)

M. Rašković

2010-11-01

Full Text Available Accelerator performance, in particular the average accelerating field and the cavity quality factor, depends on the physical and chemical characteristics of the superconducting radio-frequency (SRF cavity surface. Plasma based surface modification provides an excellent opportunity to eliminate nonsuperconductive pollutants in the penetration depth region and to remove the mechanically damaged surface layer, which improves the surface roughness. Here we show that the plasma treatment of bulk niobium (Nb presents an alternative surface preparation method to the commonly used buffered chemical polishing and electropolishing methods. We have optimized the experimental conditions in the microwave glow discharge system and their influence on the Nb removal rate on flat samples. We have achieved an etching rate of 1.7  μm/min⁡ using only 3% chlorine in the reactive mixture. Combining a fast etching step with a moderate one, we have improved the surface roughness without exposing the sample surface to the environment. We intend to apply the optimized experimental conditions to the preparation of single cell cavities, pursuing the improvement of their rf performance.

Influence of pre-heating on the surface modification of powder-metallurgy processed cold-work tool steel during laser surface melting

Energy Technology Data Exchange (ETDEWEB)

Šturm, Roman, E-mail: roman.sturm@fs.uni-lj.si [University of Ljubljana, Faculty of Mechanical Engineering, Aškerčeva 6, 1000 Ljubljana (Slovenia); Štefanikova, Maria [University of Ljubljana, Faculty of Mechanical Engineering, Aškerčeva 6, 1000 Ljubljana (Slovenia); Steiner Petrovič, Darja [Institute of Metals and Technology, Lepi pot 11, 1000 Ljubljana (Slovenia)

2015-01-15

Graphical abstract: - Highlights: • Heat-treatment protocol for laser surface melting of cold-work tool steel is proposed. • The laser melted steel surface is hardened, and morphologically modified. • The pre-heating of substrate creates a crack-and pore-free steel surface. • The optimum pre-heating temperature is determined to be 350 °C. • Using pre-heating the quantity of retained austenite is reduced. - Abstract: In this study we determine the optimal parameters for surface modification using the laser surface melting of powder-metallurgy processed, vanadium-rich, cold-work tool steel. A combination of steel pre-heating, laser surface melting and a subsequent heat treatment creates a hardened and morphologically modified surface of the selected high-alloy tool steel. The pre-heating of the steel prior to the laser surface melting ensures a crack- and pore-free modified surface. Using a pre-heating temperature of 350 °C, the extremely fine microstructure, which typically evolves during the laser-melting, became slightly coarser and the volume fraction of retained austenite was reduced. In the laser-melted layer the highest values of microhardness were achieved in the specimens where a subsequent heat treatment at 550 °C was applied. The performed thermodynamic calculations were able to provide a very valuable assessment of the liquidus temperature and, especially, a prediction of the chemical composition as well as the precipitation and dissolution sequence for the carbides.

Correlation of H- production and the work function of a surface in a hydrogen plasma

International Nuclear Information System (INIS)

Wada, M.

1983-03-01

Surface-plasma negative hydrogen ion sources are being developed as possible parts for future neutral beam systems. In these ion sources, negative hydrogen ions (H - ) are produced at low work function metal surfaces immersed in hydrogen plasmas. To investigate the correlation between the work function and the H - production at the surface with a condition similar to the one in the actual plasma ion source, these two parameters were simultaneously measured in the hydrogen plasma environment

Determination of B-complex vitamins in pharmaceutical formulations by surface-enhanced Raman spectroscopy

Science.gov (United States)

Junior, Benedito Roberto Alvarenga; Soares, Frederico Luis Felipe; Ardila, Jorge Armando; Durango, Luis Guillermo Cuadrado; Forim, Moacir Rossi; Carneiro, Renato Lajarim

2018-01-01

The aim of this work was to quantify B-complex vitamins in pharmaceutical samples by surface enhanced Raman spectroscopy technique using gold colloid substrate. Synthesis of gold nanoparticles was performed according to an adapted Turkevich method. Initial essays were able to suggest the orientation of molecules on gold nanoparticles surface. Central Composite design was performed to obtain the highest SERS signal for nicotinamide and riboflavin. The evaluated parameters in the experimental design were volume of AuNPs, concentration of vitamins and sodium chloride concentration. The best condition for nicotinamide was NaCl 2.3 × 10- 3 mol L- 1 and 700 μL of AuNPs colloid and this same condition showed to be adequate to quantify thiamine. The experimental design for riboflavin shows the best condition at NaCl 1.15 × 10- 2 mol L- 1 and 2.8 mL of AuNPs colloid. It was possible to quantify thiamine and nicotinamide in presence of others vitamins and excipients in two solid multivitamin formulations using the standard addition procedure. The standard addition curve presented a R2 higher than 0.96 for both nicotinamide and thiamine, at orders of magnitude 10- 7 and 10- 8 mol L- 1, respectively. The nicotinamide content in a cosmetic gel sample was also quantified by direct analysis presenting R2 0.98. The t-student test presented no significant difference regarding HPLC method. Despite the experimental design performed for riboflavin, it was not possible its quantification in the commercial samples.

"It's Not My Problem": The Growth of Non-Standard Work and Its Impact on Vocational Education and Training in Australia.

Science.gov (United States)

Hall, Richard; Bretherton, Tanya; Buchanan, John

A study investigated implications of the increase in non-standard forms of employment (casual work, working through labor-hire companies, and work that is outsourced) for vocational education and training (VET) in Australia. Data sources were published statistics on growth of non-standard work; research on reasons for the growth and the business…

Correlation of H- production and the work function of a surface in a hydrogen plasma

International Nuclear Information System (INIS)

Wada, M.

1983-01-01

Surface-plasma negative hydrogen ion sources are being developed as possible parts for future netural beam systems. In these ion sources, negative hydrogen ions (H - ) are produced at low work function metal surfaces immersed in hydrogen plasmas. To investigate the correlation between the work function and the H-production at the surface with a condition similar to the one in the actual plasma ion source, these two parameters were simultaneously measured in the hydrogen plasma environment. The photoelectron emission currents from Mo and Cu surfaces in a cesiated hydrogen discharge were measured in the photon energy range from 1.45 to 4.14 eV, to determine the work function based on Fowler's theory. A small magnetic line cusp plasma container was specially designed to minimize the plasma noise and to realize the efficient collection of incident light onto the target. The photelectron current was detected phase sensitively and could be measured with reasonable accuracy up to about 5 x 10 11 cm -3 of the plasma electron density. As Cs density was increased in the hydrogen discharge, the work function decreased until it reached a minimum value. This value of the lowest work function was approximately 1.4 eV for both Mo and Cu surfaces, and the detected total H - current was a maximum at this condition

Workflow standardization of a novel team care model to improve chronic care: a quasi-experimental study.

Science.gov (United States)

Panattoni, Laura; Hurlimann, Lily; Wilson, Caroline; Durbin, Meg; Tai-Seale, Ming

2017-04-19

Team-based chronic care models have not been widely adopted in community settings, partly due to their varying effectiveness in randomized control trials, implementation challenges, and concerns about physician acceptance. The Palo Alto Medical Foundation designed and implemented "Champion," a novel team-based model that includes new standard work (e.g. proactive patient outreach, pre-visit schedule grooming, depression screening, care planning, health coaching) to support patients' self-management of hypertension and diabetes. We investigated whether Champion improved clinical outcomes. We conducted a quasi-experimental study comparing the Champion clinic-level intervention (n = 38 physicians) with a usual care clinic (n = 37 physicians) in Northern California. The primary outcomes, blood pressure and glycohemoglobin (A1c), were analyzed using a piecewise linear growth curve model for patients exposed to a Champion physician visit (n = 3156) or usual care visit (n = 8034) in the two years prior and one year post implementation. Secondary outcomes were provider experience, compared at baseline and 12 months in both the intervention and usual care clinics using multi-level ordered logistic modeling, and electronic health record based fidelity measures. Compared to usual care, in the first 6 months after a Champion physician visit, diabetes patients aged 18-75 experienced an additional -1.13 mm Hg (95% CI: -2.23 to -0.04) decline in diastolic blood pressure and -0.47 (95% CI: -0.61 to -0.33) decline in A1c. There were no additional improvements in blood pressure or A1c 6 to 12 months post physician visit. At 12 months, Champion physicians reported improved experience with managing chronic care patients in 6 of 7 survey items (p work was uneven; depression screening was the most commonly documented element (85% of patients), while care plans were the least (30.8% of patients). Champion standard work improved glycemic control over the first 6�

Comparison of analytical and experimental subsonic steady and unsteady pressure distributions for a high-aspect-ratio-supercritical wing model with oscillating control surfaces

Science.gov (United States)

Mccain, W. E.

1982-01-01

The results of a comparative study using the unsteady aerodynamic lifting surface theory, known as the Doublet Lattice method, and experimental subsonic steady- and unsteady-pressure measurements, are presented for a high-aspect-ratio supercritical wing model. Comparisons of pressure distributions due to wing angle of attack and control-surface deflections were made. In general, good correlation existed between experimental and theoretical data over most of the wing planform. The more significant deviations found between experimental and theoretical data were in the vicinity of control surfaces for both static and oscillatory control-surface deflections.

A Comparative Experimental Analysis of Tribological Properties Between Commercial Mineral Oil and Neat Castor Oil using Taguchi Method in Boundary Lubrication Regime

OpenAIRE

S. Bhaumik; S.D Pathak

2016-01-01

The present work aims to carry out a comparative experimental analysis of tribological properties of 372cSt mineral oil and 229cSt castor oil. The antiwear and extreme pressure properties of both the oils have been analysed according to ASTM G 99 and ASTM D-2783 standards. The surfaces of the balls and pins after tribo tests have been analysed using Scanning Electron Microscope (SEM) images. The present test results predict that the antiwear and extreme pressure properties in case of the sele...

Numerical and experimental study of capillary forces in trapezoid microgrooves

Science.gov (United States)

Sheu, Tsung-Sheng; Ding, Pei-Pei; Chen, Ping-Hei

1999-08-01

The evaporation of thin liquid films is of significant importance in a wide variety of heat transfer problems. The vaporization process of thin liquid films in a trapezoid microgroove channel was investigated both numerically and experimentally. In order to predict the wetted axial length of capillary flow in a trapezoid microgroove, the nonlinear governing equation was solved numerically and a simplified algebraic equation was also derived. The parameters include the input heat flux, tilt angle of grooved surface, thermophysical properties of working fluid, and geometric parameters of microgrooves. In order to investigate the effect of geometric parameters of microgrooves on the wetted axial length, a series of either trapezoid or triangular microgrooves was machined on the surface of copper test devices for experimental measurements. Measurements were conducted using either methanol or ethanol as working fluid at four different tilt angles of grooved surface and four applied input heat flux values. The wetted axial length was measured using microscopy observation. The predicted results of the algebraic equation are found to be in reasonable agreement with the experimental data, especially for cases of higher tilt angle or higher heat flux. Besides, using microgrooves of triangular shape or using methanol as working fluid can increase the wetted axial length of microgrooves.

Effect of potential attraction term on surface tension of ionic liquids

Science.gov (United States)

Vaziri, N.; Khordad, R.; Rezaei, G.

2018-03-01

In this work, we have studied the effect of attraction term of molecular potential on surface tension of ionic liquids (ILs). For this purpose, we have introduced two different potential models to obtain analytical expressions for the surface tension of ILs. The introduced potential models have different attraction terms. The obtained surface tensions in this work have been compared with other theoretical methods and also experimental data. Using the calculated surface tension, the sound velocity is also estimated. We have studied the structural effects on the surface tensions of imidazolium-based ionic liquids. It is found that the cation alkyl chain length and the anion size play important roles to the surface tension of the selected ionic liquids. The calculated surface tensions show a good harmony with experimental data. It is clear that the attraction term of molecular potential has an important role on surface tension and sound velocity of our system.

Work relating to defect assessment undertaken by activity group 2 of the European Commission's working group on codes and standards. WGCS overview

International Nuclear Information System (INIS)

Townley, C.H.A.; Guinovart, J.

1995-01-01

For about twenty years, the Working Group on Codes and Standards has been an Advisory Group of the European Commission and three sub-groups AG1, AG2 and AG3, were formed to consider manufacture and inspection, structural mechanics and materials topics respectively. Representation on the Working Group and its sub-groups comes from designers, utilities and atomic energy agencies in those member States with active nuclear power programmes. There has also been a very valuable input from universities and research organisations in the countries concerned. The method of working is to identify topics on which there is a difference of opinion; projects are set up to review the up to date scientific and technological knowledge. The investigations are undertaken collaboratively by specialists from as many countries as can contribute and there is an obligation to reach conclusions which can be put to practical use by engineers. While the Working group and its sub-groups are not directly involved in the production of standards, there is a very important input to the pre-standardization process. The work produced by AG2 covered a wide range of subjects associated with structural integrity, mainly concerning the Fast Breeder Reactors. Since 1991 the Group has progressively set up Light Water Reactor programmes. Currently, most of efforts are devoted to Thermal Reactors with a minor extent to Fast Breeder Reactors. The present paper is mainly concerned with those aspects of the AG2 activities which have a bearing on defect assessment. Although work was initiated as part of the FBR programme, it must be remembered that the greater part of it can be extended to a wide range of high temperature plants. Concerning the LWR programmes, an overview on current selected studies is being provided in this paper. (authors). 23 refs

Standard working procedures in production of traditionally fermented Sremska sausage

Directory of Open Access Journals (Sweden)

Vesković-Moračanin Slavica

2011-01-01

Full Text Available Investigations conducted within project "Techonological and protective characteristics of autochthonous strains of lactic acid bacteria isolated from traditional fermented sausages and possibilities for their implementation in the meat industry" (Project Number: 20127, financed on behalf of the Ministry for Science and Technology of the Republic of Serbia, have provided an answer on the characteristics of the quality of the used raw materials for the production of Sremska sausage - one of the most well-known Serbian traditionally fermented sausages (choice of meat, fatty tissue, additives and spices, and data have been registered in connection with the procedures of their processing, microclimatic conditions have been established (temperature, relative humidity, and air circulation during the entire process of production and fermentation, as well as the presence and types of microorganisms, primarily lactic acid bacteria (BMK, the carrier of lactic fermentation. The most important characteristics of the filling have been established, the smoking regimen, the regimens of fermentation, maturing, drying, as well as the parameters for quality and safety of the finished product. At the same time, the standard working procedure has been determined for the preparation of the meat, fatty tissue, the forming and inserting of the filling into the wrappers, as well as the characteristics of the finished products. The given standard working procedure should serve as a guideline for the meat industry in the production process of this traditional fermented sausage.

Some observations on boiling heat transfer with surface oscillation

International Nuclear Information System (INIS)

Miyashita, H.

1992-01-01

The effects of surface oscillation on pool boiling heat transfer are experimentally studied. Experiments were performed in saturated ethanol and distilled water, covering the range from nucleate to film boiling except in the transition region. Two different geometries were employed as the heating surface with the same wetting area, stainless steel pipe and molybdenum ribbon. The results confirm earlier work on the effect of surface oscillation especially in lower heat flux region of nucleate boiling. Interesting boiling behavior during surface oscillation is observed, which was not referred to in previous work. (2 figures) (Author)

Do European Standard Disinfectant tests truly simulate in-use microbial and organic soiling conditions on food preparation surfaces?

Science.gov (United States)

Meyer, B; Morin, V N; Rödger, H-J; Holah, J; Bird, C

2010-04-01

The results from European standard disinfectant tests are used as one basis to approve the use of disinfectants in Europe. The design of these laboratory-based tests should thus simulate as closely as possible the practical conditions and challenges that the disinfectants would encounter in use. No evidence is available that the organic and microbial loading in these tests simulates actual levels in the food service sector. Total organic carbon (TOC) and total viable count (TVC) were determined on 17 visibly clean and 45 visibly dirty surfaces in two restaurants and the food preparation surfaces of a large retail store. These values were compared to reference values recovered from surfaces soiled with the organic and microbial loading, following the standard conditions of the European Surface Test for bactericidal efficacy, EN 13697. The TOC reference values for clean and dirty conditions were higher than the data from practice, but cannot be regarded as statistical outliers. This was considered as a conservative assessment; however, as additional nine TOC samples from visibly dirty surfaces were discarded from the analysis, as their loading made them impossible to process. Similarly, the recovery of test organisms from surfaces contaminated according to EN 13697 was higher than the TVC from visibly dirty surfaces in practice; though they could not be regarded as statistical outliers of the whole data field. No correlation was found between TVC and TOC in the sampled data, which re-emphasizes the potential presence of micro-organisms on visibly clean surfaces and thus the need for the same degree of disinfection as visibly dirty surfaces. The organic soil and the microbial burden used in EN disinfectant standards represent a realistic worst-case scenario for disinfectants used in the food service and food-processing areas.

Electrostatic Properties of PE and PTFE Subjected to Atmospheric Pressure Plasma Treatment; Correlation of Experimental Results with Atomistic Modeling

Science.gov (United States)

Trigwell, Steve; Boucher, Derrick; Calle, Carlos

2006-01-01

The use of an atmospheric pressure glow discharge (APGD) plasma was used at KSC to increase the hydrophilicity of spaceport materials to enhance their surface charge dissipation and prevent possible ESD in spaceport operations. Significant decreases in charge decay times were observed after tribocharging the materials using the standard KSC tribocharging test. The polarity and amount of charge transferred was dependent upon the effective work function differences between the respective materials. In this study, polyethylene (PE) and polytetrafluoroethylene (PTFE) were exposed to a He+O2 APGD. The pre and post treatment surface chemistry was analyzed by X-ray photoelectron spectroscopy and contact angle measurements. Semi-empirical and ab initio calculations were performed to correlate the experimental results with some plausible molecular and electronic structure features of the oxidation process. For the PE, significant surface oxidation was observed, as indicated by XPS showing C-O, C=O, and O-C=O bonding, and a decrease in the surface contact angle from 98.9 deg to 61.2 deg. For the PTFE, no C-O bonding appeared and the surface contact angle increased indicating the APGD only succeeded in cleaning the PTFE surface without affecting the surface structure. The calculations using the PM3 and DFT methods were performed on single and multiple oligomers to simulate a wide variety of oxidation scenarios. Calculated work function results suggest that regardless of oxidation mechanism, e.g. -OH, =0 or a combination thereof, the experimentally observed levels of surface oxidation are unlikely to lead to a significant change in the electronic structure of PE and that its increased hydrophilic properties are the primary reason for the observed changes in its electrostatic behavior. The calculations for PTFE argue strongly against significant oxidation of that material, as confirmed by the XPS results.

Specific Features of Chip Making and Work-piece Surface Layer Formation in Machining Thermal Coatings

Directory of Open Access Journals (Sweden)

V. M. Yaroslavtsev

2016-01-01

Full Text Available A wide range of unique engineering structural and performance properties inherent in metallic composites characterizes wear- and erosion-resistant high-temperature coatings made by thermal spraying methods. This allows their use both in manufacturing processes to enhance the wear strength of products, which have to operate under the cyclic loading, high contact pressures, corrosion and high temperatures and in product renewal.Thermal coatings contribute to the qualitative improvement of the technical level of production and product restoration using the ceramic composite materials. However, the possibility to have a significantly increased product performance, reduce their factory labour hours and materials/output ratio in manufacturing and restoration is largely dependent on the degree of the surface layer quality of products at their finishing stage, which is usually provided by different kinds of machining.When machining the plasma-sprayed thermal coatings, a removing process of the cut-off layer material is determined by its distinctive features such as a layered structure, high internal stresses, low ductility material, high tendency to the surface layer strengthening and rehardening, porosity, high abrasive properties, etc. When coatings are machined these coating properties result in specific characteristics of chip formation and conditions for formation of the billet surface layer.The chip formation of plasma-sprayed coatings was studied at micro-velocities using an experimental tool-setting microscope-based setup, created in BMSTU. The setup allowed simultaneous recording both the individual stages (phases of the chip formation process and the operating force factors.It is found that formation of individual chip elements comes with the multiple micro-cracks that cause chipping-off the small particles of material. The emerging main crack in the cut-off layer of material leads to separation of the largest chip element. Then all the stages

Applicability of surface complexation modelling in TVO's studies on sorption of radionuclides

International Nuclear Information System (INIS)

Carlsson, T.

1994-03-01

The report focuses on the possibility of applying surface complexation theories to the conditions at a potential repository site in Finland and of doing proper experimental work in order to determine necessary constants for the models. The report provides background information on: (1) what type experiments should be carried out in order to produce data for surface complexation modelling of sorption phenomena under potential Finnish repository conditions, and (2) how to design and perform properly such experiments, in order to gather data, develop models or both. The report does not describe in detail how proper surface complexation experiments or modelling should be carried out. The work contains several examples of information that may be valuable in both modelling and experimental work. (51 refs., 6 figs., 4 tabs.)

A three-layer model of self-assembly induced surface-energy variation experimentally extracted by using nanomechanically sensitive cantilevers

International Nuclear Information System (INIS)

Zuo Guomin; Li Xinxin

2011-01-01

This research is aimed at elucidating surface-energy (or interfacial energy) variation during the process of molecule-layer self-assembly on a solid surface. A quasi-quantitative plotting model is proposed and established to distinguish the surface-energy variation contributed by the three characteristic layers of a thiol-on-gold self-assembled monolayer (SAM), namely the assembly-medium correlative gold/head-group layer, the chain/chain interaction layer and the tail/medium layer, respectively. The data for building the model are experimentally extracted from a set of correlative thiol self-assemblies in different media. The variation in surface-energy during self-assembly is obtained by in situ recording of the self-assembly induced nanomechanical surface-stress using integrated micro-cantilever sensors. Based on the correlative self-assembly experiment, and by using the nanomechanically sensitive self-sensing cantilevers to monitor the self-assembly induced surface-stressin situ, the experimentally extracted separate contributions of the three layers to the overall surface-energy change aid a comprehensive understanding of the self-assembly mechanism. Moreover, the quasi-quantitative modeling method is helpful for optimal design, molecule synthesis and performance evaluation of molecule self-assembly for application-specific surface functionalization.

Outlining precision boundaries among areas with different variability standards using magnetic susceptibility and geomorphic surfaces

OpenAIRE

Matias,Sammy S. R.; Marques Júnior,José; Siqueira,Diego S.; Pereira,Gener T.

2014-01-01

There is an increasing demand for detailed maps that represent in a simplified way the knowledge of the variability of a particular area or region maps. The objective was to outline precision boundaries among areas with different accuracy variability standards using magnetic susceptibility and geomorphic surfaces. The study was conducted in an area of 110 ha, which identified three compartment landscapes based on the geomorphic surfaces model. To determinate pH, organic matter, phosphorus, po...

Numerical and experimental determination of surface temperature and moisture evolution in a field soil

Science.gov (United States)

Akinyemi, Olukayode D.; Mendes, Nathan

2007-03-01

Knowledge about the dynamics of soil moisture and heat, especially at the surface, provides important insights into the physical processes governing their interactions with the atmosphere, thereby improving the understanding of patterns of climate dynamics. In this context the paper presents the numerical and field experimental results of temperature and moisture evolution, which were measured on the surface of a sandy soil at Abeokuta, south-western Nigeria. An unconditionally stable numerical method was used, which linearizes the vapour concentration driving-potential term giving the moisture exchanged at the boundaries in terms of temperature and moisture content, and simultaneously solves the governing equations for each time step. The model avoids stability problems and limitations to low moisture contents and the usual assumption of constant thermal conductivity. Instantaneous temperature measurements were made at the surface using a thermocouple, while the gravimetric method was employed to determine the volumetric water contents at some specific hours of the experimental period. The observed experimental data compared fairly well with the predicted values, with both having correlation coefficients greater than 0.9 and consequently following a common diurnal trend. The sensitivity of the model was very high to the choice of simulation parameters, especially grid size refinement and time step. While the model underestimated the soil moisture content at 6 a.m. and 10 p.m., the measured temperatures were however overestimated. When compared to moisture content, average errors for temperature were low resulting in a minimal absolute difference in amplitude of 0.81 °C.

Mapping surface properties of sinusoidal roughness standards by TPM

International Nuclear Information System (INIS)

Liu, X; Rubert, P

2005-01-01

We report our investigation on the surface properties of sinusoidal roughness standards made from pure electroformed nickel. Two specimens having a sinusoidal profile with nominal R a of 0.36 μm and a peak spacing of 25 μm are chosen for this investigation. One specimen is further treated with a hard protective coating of nickel-boron. The surface topography, friction, hardness and Young's modulus of the specimens were measured by a novel instrument, the multi-function Tribological Probe Microscope (TPM). The results show that hardness of these two specimens is 14.1 GPa for uncoated specimen and 25.7 GPa for the coated one, while the Young's modulus is 188 GPa and 225 GPa, respectively. The ramping force was set to 3mN for both the specimens and the effect of the tip penetration was investigated by comparing the topography measurements before and after hardness mapping. It has been found out that there is no significant change in the averaged profiles over the scanned area, which indicates the topography distortion seen in the multi-function mapping, is recoverable. Cross correlation between topography and its corresponding hardness/Young's modulus has been carried out and the result will be discussed in the paper

Influence of undergraduate nursing student teaching methods on learning standard precautions and transmission-based precautions: Experimental research.

Science.gov (United States)

Kappes Ramirez, Maria Soledad

2018-02-01

An experimental study was performed with undergraduate nursing students in order to determine, between two methodologies, which is the best for learning standard precautions and precautions based on disease transmission mechanisms. Students in the sample are stratified by performance, with the experimental group (49 students) being exposed to self-instruction and clinical simulation on the topic of standard precautions and special precautions according to disease transmission mechanisms. Conventional classes on the same topics were provided to the control group (49 students). The experimental group showed the best performance in the multiple-choice post-test of knowledge (p=0.002) and in the assessment of essay questions (p=0.043), as well as in the evaluation of a simulated scenario, in relation to the control group. This study demonstrates that it is possible to transfer some teaching subjects on the prevention of Healthcare Associated Infections (HAIs) to self-learning by means of virtual teaching strategies with good results. This allows greater efficiency in the allocation of teachers to clinical simulation or learning situations in the laboratory, where students can apply what they have learned in the self-instruction module. Copyright © 2017 Elsevier Ltd. All rights reserved.

30 CFR 71.404 - Application for waiver of surface facilities requirements.

Science.gov (United States)

2010-07-01

... requirements. 71.404 Section 71.404 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY HEALTH STANDARDS-SURFACE COAL MINES AND SURFACE WORK AREAS... Facilities at Surface Coal Mines § 71.404 Application for waiver of surface facilities requirements. (a...

Technical activities, 1990: Surface Science Division

International Nuclear Information System (INIS)

Powell, C.J.

1991-05-01

The report summarizes technical activities and accomplishments of the NIST Surface Science Division during Fiscal Year 1990. Overviews are presented of the Division and of its three constituent groups: Surface Dynamical Processes, Thin Films and Interfaces, and Surface Spectroscopies and Standards. These overviews are followed by reports of selected technical accomplishments during the year. A summary is given of Division outputs and interactions that includes lists of publications, talks, committee assignments, seminars (including both Division seminars and Interface Science seminars arranged through the Division), conferences organized, and a standard reference material certified. Finally, lists are given of Division staff and of guest scientists who have worked in the Division during the past year

Biomechanical aspects of playing surfaces.

Science.gov (United States)

Nigg, B M; Yeadon, M R

1987-01-01

The purpose of this paper is to discuss some biomechanical aspects of playing surfaces with special focus on (a) surface induced injuries, (b) methodologies used to assess surfaces and (c) findings from various sports. The paper concentrates primarily on questions related to load on the athlete's body. Data from epidemiological studies suggest strongly that the surface is an important factor in the aetiology of injuries. Injury frequencies are reported to be significantly different for different surfaces in several sports. The methodologies used to assess surfaces with respect to load or performance include material tests and tests using experimental subjects. There is only little correlation between the results of these two approaches. Material tests used in many standardized test procedures are not validated which suggests that one should exercise restraint in the interpretation of these results. Point elastic surfaces are widely studied while area elastic surfaces have received little attention to date. Questions of energy losses on sport surfaces have rarely been studied scientifically.

A novel test method for quantifying surface tack of polypropylene compound surfaces

Directory of Open Access Journals (Sweden)

2011-11-01

Full Text Available While adhesiveness is required for polymer surfaces in special applications, tacky surfaces are generally undesirable in many applications like automotive interior parts. The tackiness of polymer surface results from a combination of composition and additivation, and it can change significantly in natural or accelerated ageing. Since there is no established, uniform method to characterize surface tack, the major focus of the present work was on the development of an objective quantification method. A setup having a soft die tip attached to a standard tensile tester was developed aiming for correlation to the human sense of touch. Three different model thermoplastic polyolefin (TPO compound formulations based on a high-impact isotactic polypropylene (iPP composition with varying amounts and types of anti-scratch additives were used for these investigations. As the surface tack phenomenon is related to ageing and weathering, the material’s examination was also performed after various intervals of weathering. The developed method allows a fast assessment of the effect of polymer composition variations and different additive formulations on surface tack and gives identical rankings as the standardized haptic panel.

Experimental demonstration of CMOS-compatible long-range dielectric-loaded surface plasmon-polariton waveguides (LR-DLSPPWs)

DEFF Research Database (Denmark)

Zektzer, Roy; Desiatov, Boris; Mazurski, Noa

2015-01-01

We demonstrate the design, fabrication and experimental characterization of long-range dielectric-loaded surface plasmon-polariton waveguides (LR-DLSPPWs) that are compatible with complementary metal-oxide semiconductor (CMOS) technology. The demonstrated waveguides feature good mode confinement...

Experimental Investigation of Surface Layer Properties of High Thermal Conductivity Tool Steel after Electrical Discharge Machining

Directory of Open Access Journals (Sweden)

Rafał Świercz

2017-12-01

Full Text Available New materials require the use of advanced technology in manufacturing complex shape parts. One of the modern materials widely used in the tool industry for injection molds or hot stamping dies is high conductivity tool steel (HTCS 150. Due to its hardness (55 HRC and thermal conductivity at 66 W/mK, this material is difficult to machine by conventional treatment and is being increasingly manufactured by nonconventional technology such as electrical discharge machining (EDM. In the EDM process, material is removed from the workpiece by a series of electrical discharges that cause changes to the surface layers properties. The final state of the surface layer directly influences the durability of the produced elements. This paper presents the influence of EDM process parameters: discharge current Ic and the pulse time ton on surface layer properties. The experimental investigation was carried out with an experimental methodology design. Surface layers properties including roughness 3D parameters, the thickness of the white layer, heat affected zone, tempered layer and occurring micro cracks were investigated and described. The influence of the response surface methodology (RSM of discharge current Ic and the pulse time ton on the thickness of the white layer and roughness parameters Sa, Sds and Ssc were described and established.

Experimental investigation of thermal emittance components of copper photocathode

Directory of Open Access Journals (Sweden)

H. J. Qian

2012-04-01

Full Text Available With progress of photoinjector technology, thermal emittance has become the primary limitation of electron beam brightness. Extensive efforts have been devoted to study thermal emittance, but experiment results differ between research groups and few can be well interpreted. Besides the ambiguity of photoemission mechanism, variations of cathode surface conditions during cathode preparation, such as work function, field enhancement factor, and surface roughness, will cause thermal emittance differences. In this paper, we report an experimental study of electric field dependence of copper cathode quantum efficiency (QE and thermal emittance in a radio frequency (rf gun, through which in situ cathode surface parameters and thermal emittance contributions from photon energy, Schottky effect, and surface roughness are extracted. It is found the QE of a copper cathode illuminated by a 266 nm UV laser increased substantially to 1.5×10^{-4} after cathode cleaning during rf conditioning, and a copper work function of 4.16 eV, which is much lower than nominal value (4.65 eV, was measured. Experimental results also show a thermal emittance growth as much as 0.92  mm mrad/mm at 50  MV/m due to the cathode surface roughness effect, which is consistent with cathode surface morphology measurements.

Surface oxidation on thin films affects ionization cross section induced by proton beam

International Nuclear Information System (INIS)

Bertol, Ana Paula Lamberti; Vasconcellos, M.A.Z.; Hinrichs, Ruth; Limandri, Silvina; Trincavelli, Jorge

2012-01-01

Full text: In microanalysis techniques such as Particle Induced X-ray Emission (PIXE), the transformation from intensity to concentration is made by standard less software that needs exact values of fundamental parameters such as the ionization cross section, transition probabilities of the different electronic levels, and fluorescent yield. The three parameters together measure the photon generating probability of an electronic transition and can be determined experimentally under the name of production cross section. These measurements are performed on thin films, with thickness around 10 nm, but most studies do not take into account any spontaneous surface oxidation. In this work, in the attempt to obtain cross section values of Al, Si and Ti, in metallic and oxide films, the influence of surface oxidation on the metallic films was established. Simulations considering the oxidation with the software SIMNRA on the Rutherford backscattering (RBS) spectra obtained from the films provided mass thickness values used to calculate the cross section data that were compared with theoretical values (PWBA and ECPSSR), and with experimental values and empirical adjustments from other studies. The inclusion of the natural oxidation affects the values of cross section, and may be one of the causes of discrepancies between the experimental values published in literature. (author)

Experimental modeling of aerosols produced by microorganisms in working area air as risk factor exerting hazardous impacts on health of workers employed at biotechnological production

Directory of Open Access Journals (Sweden)

N.V. Dudchik

2017-09-01

Full Text Available Scientific foundation and practices in the sphere of hygienic and ecological standardization concerning biological factors of the environment have a number of peculiarities and are methodically less developed than chemical factors standardization. Efficient industrial control over maximum permissible concentrations of standardized microorganisms-producers in working area air is based on validated instrumental techniques of quantitative assessment. Our goal was to create experimental models for microorganisms-producers' aerosols of a multi-component microbe specimen in working area air as a risk factor causing impacts on health of workers employed at biotechnological production; another task was to work out a procedure for measuring Pseudomonas aurantiaca B-162/255.17concentration and cells and spores of Bacillus sp. BB58-3 strain in working area air. We gave grounds for a technology aimed at quantitative determination of microorganisms-producers in working area air in a modeling experiment; it was based on conventional stages and tech-niques accepted in microbiological practices, namely air samples taking via aspiration technique allowing for a volume taken; cultivation under conditions which are optimal for examined microorganisms-producers in a nutrient medium with reduced composition; calculation of evolved colonies with specific morphological features; morphologic identification of microorganisms and colonies; calculation of microorganisms' quantity on dishes with recalculation per 1 m3 of air. Bas-ing on the detected regular concentration dependences of microbe contamination dynamics in air we worked out a proce-dure for quantitative determination of microorganisms-producers; we also performed metrological estimate of opera-tional properties for assessing microorganisms-producers of a multi-component microbe specimen as a risk factor caus-ing hazardous impacts on health of workers employed at biotechnological production. We validated our

Photonic crystals possessing multiple Weyl points and the experimental observation of robust surface states

Science.gov (United States)

Chen, Wen-Jie; Xiao, Meng; Chan, C. T.

2016-01-01

Weyl points, as monopoles of Berry curvature in momentum space, have captured much attention recently in various branches of physics. Realizing topological materials that exhibit such nodal points is challenging and indeed, Weyl points have been found experimentally in transition metal arsenide and phosphide and gyroid photonic crystal whose structure is complex. If realizing even the simplest type of single Weyl nodes with a topological charge of 1 is difficult, then making a real crystal carrying higher topological charges may seem more challenging. Here we design, and fabricate using planar fabrication technology, a photonic crystal possessing single Weyl points (including type-II nodes) and multiple Weyl points with topological charges of 2 and 3. We characterize this photonic crystal and find nontrivial 2D bulk band gaps for a fixed kz and the associated surface modes. The robustness of these surface states against kz-preserving scattering is experimentally observed for the first time. PMID:27703140

Nitrile versus isonitrile adsorption at interstellar grain surfaces. II. Carbonaceous aromatic surfaces

Science.gov (United States)

Bertin, M.; Doronin, M.; Michaut, X.; Philippe, L.; Markovits, A.; Fillion, J.-H.; Pauzat, F.; Ellinger, Y.; Guillemin, J.-C.

2017-12-01

Context. Almost 20% of the 200 different species detected in the interstellar and circumstellar media present a carbon atom linked to nitrogen by a triple bond. Of these 37 molecules, 30 are nitrile R-CN compounds, the remaining 7 belonging to the isonitrile R-NC family. How these species behave in their interactions with the grain surfaces is still an open question. Aims: In a previous work, we have investigated whether the difference between nitrile and isonitrile functional groups may induce differences in the adsorption energies of the related isomers at the surfaces of interstellar grains of various nature and morphologies. This study is a follow up of this work, where we focus on the adsorption on carbonaceous aromatic surfaces. Methods: The question is addressed by means of a concerted experimental and theoretical approach of the adsorption energies of CH3CN and CH3NC on the surface of graphite (with and without surface defects). The experimental determination of the molecule and surface interaction energies is carried out using temperature-programmed desorption in an ultra-high vacuum between 70 and 160 K. Theoretically, the question is addressed using first-principle periodic density functional theory to represent the organised solid support. Results: The adsorption energy of each compound is found to be very sensitive to the structural defects of the aromatic carbonaceous surface: these defects, expected to be present in a large numbers and great diversity on a realistic surface, significantly increase the average adsorption energies to more than 50% as compared to adsorption on perfect graphene planes. The most stable isomer (CH3CN) interacts more efficiently with the carbonaceous solid support than the higher energy isomer (CH3NC), however.

Theoretical and experimental high energy physics

International Nuclear Information System (INIS)

Gasiorowicz, S.; Ruddick, K.

1988-01-01

This report discusses experimental and theoretical work in High Energy Physics. Some topics discussed are: quantum field theory; supersymmetry; cosmology; superstring model; relic photinos; inflationary universe; dark matter; standard model; supernovae; semileptonic decay; quantum Langevin equation; underground neutrino detection at Soudan; strange quark systems; cosmic ray detection; superconducting super collider detectors; and studies of direct photon production

Experimentally testing the standard cosmological model

Energy Technology Data Exchange (ETDEWEB)

Schramm, D.N. (Chicago Univ., IL (USA) Fermi National Accelerator Lab., Batavia, IL (USA))

1990-11-01

The standard model of cosmology, the big bang, is now being tested and confirmed to remarkable accuracy. Recent high precision measurements relate to the microwave background; and big bang nucleosynthesis. This paper focuses on the latter since that relates more directly to high energy experiments. In particular, the recent LEP (and SLC) results on the number of neutrinos are discussed as a positive laboratory test of the standard cosmology scenario. Discussion is presented on the improved light element observational data as well as the improved neutron lifetime data. alternate nucleosynthesis scenarios of decaying matter or of quark-hadron induced inhomogeneities are discussed. It is shown that when these scenarios are made to fit the observed abundances accurately, the resulting conclusions on the baryonic density relative to the critical density, {Omega}{sub b}, remain approximately the same as in the standard homogeneous case, thus, adding to the robustness of the standard model conclusion that {Omega}{sub b} {approximately} 0.06. This latter point is the deriving force behind the need for non-baryonic dark matter (assuming {Omega}{sub total} = 1) and the need for dark baryonic matter, since {Omega}{sub visible} < {Omega}{sub b}. Recent accelerator constraints on non-baryonic matter are discussed, showing that any massive cold dark matter candidate must now have a mass M{sub x} {approx gt} 20 GeV and an interaction weaker than the Z{sup 0} coupling to a neutrino. It is also noted that recent hints regarding the solar neutrino experiments coupled with the see-saw model for {nu}-masses may imply that the {nu}{sub {tau}} is a good hot dark matter candidate. 73 refs., 5 figs.

Experimentally testing the standard cosmological model

International Nuclear Information System (INIS)

Schramm, D.N.

1990-11-01

The standard model of cosmology, the big bang, is now being tested and confirmed to remarkable accuracy. Recent high precision measurements relate to the microwave background; and big bang nucleosynthesis. This paper focuses on the latter since that relates more directly to high energy experiments. In particular, the recent LEP (and SLC) results on the number of neutrinos are discussed as a positive laboratory test of the standard cosmology scenario. Discussion is presented on the improved light element observational data as well as the improved neutron lifetime data. alternate nucleosynthesis scenarios of decaying matter or of quark-hadron induced inhomogeneities are discussed. It is shown that when these scenarios are made to fit the observed abundances accurately, the resulting conclusions on the baryonic density relative to the critical density, Ω b , remain approximately the same as in the standard homogeneous case, thus, adding to the robustness of the standard model conclusion that Ω b ∼ 0.06. This latter point is the deriving force behind the need for non-baryonic dark matter (assuming Ω total = 1) and the need for dark baryonic matter, since Ω visible b . Recent accelerator constraints on non-baryonic matter are discussed, showing that any massive cold dark matter candidate must now have a mass M x approx-gt 20 GeV and an interaction weaker than the Z 0 coupling to a neutrino. It is also noted that recent hints regarding the solar neutrino experiments coupled with the see-saw model for ν-masses may imply that the ν τ is a good hot dark matter candidate. 73 refs., 5 figs

C-Band Airport Surface Communications System Standards Development, Phase I

Science.gov (United States)

Hall, Edward; Isaacs, James; Zelkin, Natalie; Henriksen. Steve

2010-01-01

This document is being provided as part of ITT's NASA Glenn Research Center Aerospace Communication Systems Technical Support (ACSTS) contract NNC05CA85C, Task 7: "New ATM Requirements--Future Communications, C-Band and L-Band Communications Standard Development." The proposed future C-band (5091- to 5150-MHz) airport surface communication system, referred to as the Aeronautical Mobile Airport Communications System (AeroMACS), is anticipated to increase overall air-to-ground data communications systems capacity by using a new spectrum (i.e., not very high frequency (VHF)). Although some critical services could be supported, AeroMACS will also target noncritical services, such as weather advisory and aeronautical information services as part of an airborne System Wide Information Management (SWIM) program. AeroMACS is to be designed and implemented in a manner that will not disrupt other services operating in the C-band. This report defines the AeroMACS concepts of use, high-level system requirements, and architecture; the performance of supporting system analyses; the development of AeroMACS test and demonstration plans; and the establishment of an operational AeroMACS capability in support of C-band aeronautical data communications standards to be advanced in both international (International Civil Aviation Organization, ICAO) and national (RTCA) forums. This includes the development of system parameter profile recommendations for AeroMACS based on existing Institute of Electrical and Electronics Engineering (IEEE) 802.16e- 2009 standards

Mothers’ non-standard working and childcare-related challenges : A comparison between lone and coupled mothers

OpenAIRE

Moilanen, Sanna; May, Vanessa; Räikkönen, Eija; Sevón, Eija; Laakso, Marja-Leena

2016-01-01

Purpose – The purpose of this paper is to particularly focus on lone-mother families, comparing the childcare-related challenges experienced by working lone mothers and coupled mothers in three European countries in the context of a 24/7 economy and non-standard working hours (e.g. evening, night and weekend work). Design/methodology/approach – This study utilises survey data from Finnish, Dutch and British working mothers (n=1,106) collected as part of the “Families 24/7” research ...

An experimental study on mass loading of soil particles on plant surfaces

International Nuclear Information System (INIS)

Li, J. G.; Gerzabek, M. H.; Mueck, K.

1994-01-01

Radionuclide contaminated soil adhered to plant surfaces can contribute to human ingestion dose. To determine this contribution, a method of 46 Sc neutron activation analysis was established and tested, by which a detection limit of 0.05 mg soil per g dry plant biomass can be obtained. In the field and greenhouse experiment the mass loading of soil on ryegrass (Lolium perenne L.) and broadbean (Vicia faba L.) was investigated and the contribution from rainsplash and wind erosion were evaluated separately. Soil retained on plant surfaces in field conditions in Seibersdorf/Austria was 5.77 ± 1.44 mg soil per g dry plant for ryegrass and 9.51 ± 0.73 mg soil per g dry plant for broadbean. Estimates of contribution from rainsplash and wind erosion to soil contamination of plants during the experimental period are 68 % and 32 % for broadbean 47 % and 53 % for ryegrass respectively. Mass loading results from field studies indicate that soil adhesion on plant surfaces can contribute up to 23 % of plant 137 Cs contamination, the transfer factors modified by mass loading decline differently, depending on 137 Cs concentration of the soil and the soil mass adhered to plant surfaces. (author)

He atom-surface scattering: Surface dynamics of insulators, overlayers and crystal growth

International Nuclear Information System (INIS)

Safron, S.A.; Skofronick, J.G.

1994-01-01

This progress report describes work carried out in the study of surface structure and dynamics of ionic insulators, the microscopic interactions controlling epitaxial growth and the formation of overlayers, and energy exchange in multiphonon surface scattering. The approach used is to employ high resolution helium atom scattering to study the geometry and structural features of the surfaces. Experiments have been carried out on the surface dynamics of RbCl and preliminary studies done on CoO and NiO. Epitaxial growth and overlayer dynamics experiments on the systems NaCl/NaCl(001), KBr/NaCl(001), NaCl/KBr(001) and KBr/RbCl(001) have been performed. They have collaborated with two theoretical groups to explore models of overlayer dynamics with which to compare and to interpret their experimental results. They have carried out extensive experiments on the multiphonon scattering of helium atoms from NaCl and, particularly, LiF. Work has begun on self-assembling organic films on gold and silver surfaces (alkyl thiols/Au(111) and Ag(111))

Experimental parameters for quantitative surface analysis by medium energy ion scattering, ch. 1

International Nuclear Information System (INIS)

Turkenburg, W.C.; Kersten, H.H.; Colenbrander, B.G.; Jongh, A.P. de; Saris, F.W.

1976-01-01

A new UHV chamber for surface and surface layer analysis by collision spectroscopy of backscattered ions at medium energies is described. Experimental parameters like energy, angular and depth resolution, crystal alignment and background pressure are discussed. Formulae based on the use of an electrostatic energy analyser show that the analysis can be quantitative. Effects of beam induced build-up of a hydro-carbon layer, sputter cleaning and creation of radiation damage have been investigated for Cu (110) and Ni (110). Detection sensitivity for Carbon, Oxygen and Sulfur on Cu and Ni has been found to be 0.2, 0.1 and 0.03 of a monolayer respectively

Experimental investigation of the characteristics of a laser beam passing through a fluid layer for surface quality in-process measurement

International Nuclear Information System (INIS)

Guo, Ruipeng; Tao, Zhengsu

2010-01-01

The optical characteristics of a laser beam passing through a fluid parallel layer are examined through a series of experimental tests in this project. The experimental apparatus consists of a bare surface quality measurement system and a fluid-supporting system. In the case of laser beam propagation through the static fluid layer, a modified Beckmann–Kirchhoff scattering model has been developed. Based on this model, the results of the surface quality in-process optical measurement can be amended. By extracting a ratio parameter from the image of the scattered light pattern to estimate surface roughness, the modified model can be verified quantitatively in the experimental system. As far as laser beam propagation through the flowing fluid layer is concerned, the deflection of the laser beam caused by fluid flow is small. The experiments are conducted to investigate the characteristics, and the results show that the resulting measurement error for surface quality optical measurement is in an acceptable range

NUMERICAL SIMULATION AND EXPERIMENTAL STUDY OF DRAGREDUCING SURFACE OF A REAL SHARK SKIN*

Institute of Scientific and Technical Information of China (English)

ZHANG De-yuan; LUO Yue-hao; LI Xiang; CHEN Hua-wei

2011-01-01

It is well known that shark skin surface can effectively inhabit the occurrence of turbulence and reduce the wall friction,but in order to understand the mechanism of drag reduction, one has to solve the problem of the turbulent flow on grooved-scale surface, and in that respect, the direct numerical simulation is an important tool.In this article, based on the real biological shark skin,the model of real shark skin is built through high-accurate scanning and data processing.The turbulent flow on a real shark skin is comprehensively simulated, and based on the simulation, the drag reduction mechanism is discussed.In addition, in order to validate the drag-reducing effect of shark skin surface, actual experiments were carried out in water tunnel, and the experimental results are approximately consistent with the numerical simulation.

The structure and assembly of surface layer proteins : a combined approach of in silico and experimental methods

International Nuclear Information System (INIS)

Horejs, C.

2011-01-01

Self-assembly of matter is one of nature's most sophisticated strategies to organize molecules on a large scale and to create order from disorder. Surface (S-)layer proteins self-assemble in a highly reproducible and robust fashion in order to form crystalline layers that completely cover and protect prokaryotic cells. Long conserved during evolution, S-layers constitute a unique model system to study the molecular mechanisms of functional self-assembly, while additionally, they provide a basic matrix for the specific construction of ordered nanostructures. Due to their intrinsic capabilities to self-assemble into two-dimensional crystals, the elucidation of the three-dimensional structure of single S-layer proteins demands an approach beyond conventional structure determination methods. In this work, computer simulations were combined with experimental techniques in order to study the structure and intra- and intermolecular potentials guiding the proteins to self-assemble into lattices with different symmetries. Molecular dynamics, Monte Carlo methods, small-angle X-ray scattering involving a new theoretical description, and AFM-based single-molecule force spectroscopy yield new insights into the three-dimensional structure of S-layer proteins, the location, type and distribution of amino acids in S-layer lattices, the molecular mechanisms behind the self-assembly process, the mechanical stability and adaptive structural conformations that S-layer proteins are able to establish. In silico studies - embedded in an adequate experimental and theoretical scaffold - offer the possibility to calculate structural and thermodynamic features of proteins, while this work demonstrates the growing impact of such theoretical techniques in the fascinating field of biophysics at the nano-scale. (author) [de

Influence of surface position along the working range of conoscopic holography sensors on dimensional verification of AISI 316 wire EDM machined surfaces.

Science.gov (United States)

Fernández, Pedro; Blanco, David; Rico, Carlos; Valiño, Gonzalo; Mateos, Sabino

2014-03-06

Conoscopic holography (CH) is a non-contact interferometric technique used for surface digitization which presents several advantages over other optical techniques such as laser triangulation. Among others, the ability for the reconstruction of high-sloped surfaces stands out, and so does its lower dependence on surface optical properties. Nevertheless, similarly to other optical systems, adjustment of CH sensors requires an adequate selection of configuration parameters for ensuring a high quality surface digitizing. This should be done on a surface located as close as possible to the stand-off distance by tuning frequency (F) and power (P) until the quality indicators Signal-to-Noise Ratio (SNR) and signal envelope (Total) meet proper values. However, not all the points of an actual surface are located at the stand-off distance, but they could be located throughout the whole working range (WR). Thus, the quality of a digitized surface may not be uniform. The present work analyses how the quality of a reconstructed surface is affected by its relative position within the WR under different combinations of the parameters F and P. Experiments have been conducted on AISI 316 wire EDM machined flat surfaces. The number of high-quality points digitized as well as distance measurements between different surfaces throughout the WR allowed for comparing the metrological behaviour of the CH sensor with respect to a touch probe (TP) on a CMM.

The surface physics work station: final design

International Nuclear Information System (INIS)

Landers, R.; Kleiman, G.G.; Castro, S.G.C. de; Douglas, R.A.; Nascente, P.A.P.

1996-01-01

Thanks to funding from FAPESP we will be installing in the beginning of 1997 a work station for electron spectroscopy designed for the study of clean solid surfaces and the modification of these surfaces by deposition in situ of ultra thin metallic films. The main analytical tool will be a high resolution hemispherical analyzer made by VSW-Omicrom (EA 125 HR) which is capable of better than 5 meV resolution and high transmission due to its five channeltron multi detection system. The system will also have a Rear View LEED Optics for single crystal studies. The system will be housed in a 16'' cylindrical chamber with mu metal magnetic shielding having two levels for analysis. The upper level will contain instruments for technique which do not require photons such as LEED and sample cleaning. The lower level will have the electron analyzer, conventional X-ray source (Al/Mg), electron gun for Auger, e-beam evaporators for thin film deposition and ports for the future addition of different detectors. We will have a manipulator with 5 degrees of freedom (thre translation and two rotational) and sample heating and LN cooling. Finally we will have a fast entry/preparation chamber. The pumping system will have a combination of turbomolecular and ion pumps for the main chamber and a turbo for the fast entr/prep chamber. The system will be used initially for the study of surface alloys by XPS and Photoelectron Diffraction but as soon as it is properly characterized it will be open for collaborations with other groups interested in using its capabilities. (author)

First principles study of hydroxyapatite surface

Science.gov (United States)

Slepko, Alexander; Demkov, Alexander A.

2013-07-01

The biomineral hydroxyapatite (HA) [Ca10(PO4)6(OH)2] is the main mineral constituent of mammal bone. We report a theoretical investigation of the HA surface. We identify the low energy surface orientations and stoichiometry under a variety of chemical environments. The surface most stable in the physiologically relevant OH-rich environment is the OH-terminated (1000) surface. We calculate the work function of HA and relate it to the surface composition. For the lowest energy OH-terminated surface we find the work function of 5.1 eV, in close agreement with the experimentally reported range of 4.7 eV-5.1 eV [V. S. Bystrov, E. Paramonova, Y. Dekhtyar, A. Katashev, A. Karlov, N. Polyaka, A. V. Bystrova, A. Patmalnieks, and A. L. Kholkin, J. Phys.: Condens. Matter 23, 065302 (2011), 10.1088/0953-8984/23/6/065302].

Experimental calibration and validation of sewer/surface flow exchange equations in steady and unsteady flow conditions

Science.gov (United States)

Rubinato, Matteo; Martins, Ricardo; Kesserwani, Georges; Leandro, Jorge; Djordjević, Slobodan; Shucksmith, James

2017-09-01

The linkage between sewer pipe flow and floodplain flow is recognised to induce an important source of uncertainty within two-dimensional (2D) urban flood models. This uncertainty is often attributed to the use of empirical hydraulic formulae (the one-dimensional (1D) weir and orifice steady flow equations) to achieve data-connectivity at the linking interface, which require the determination of discharge coefficients. Because of the paucity of high resolution localised data for this type of flows, the current understanding and quantification of a suitable range for those discharge coefficients is somewhat lacking. To fulfil this gap, this work presents the results acquired from an instrumented physical model designed to study the interaction between a pipe network flow and a floodplain flow. The full range of sewer-to-surface and surface-to-sewer flow conditions at the exchange zone are experimentally analysed in both steady and unsteady flow regimes. Steady state measured discharges are first analysed considering the relationship between the energy heads from the sewer flow and the floodplain flow; these results show that existing weir and orifice formulae are valid for describing the flow exchange for the present physical model, and yield new calibrated discharge coefficients for each of the flow conditions. The measured exchange discharges are also integrated (as a source term) within a 2D numerical flood model (a finite volume solver to the 2D Shallow Water Equations (SWE)), which is shown to reproduce the observed coefficients. This calibrated numerical model is then used to simulate a series of unsteady flow tests reproduced within the experimental facility. Results show that the numerical model overestimated the values of mean surcharge flow rate. This suggests the occurrence of additional head losses in unsteady conditions which are not currently accounted for within flood models calibrated in steady flow conditions.

Disinfectant wipes are appropriate to control microbial bioburden from surfaces: use of a new ASTM standard test protocol to demonstrate efficacy.

Science.gov (United States)

Sattar, S A; Bradley, C; Kibbee, R; Wesgate, R; Wilkinson, M A C; Sharpe, T; Maillard, J-Y

2015-12-01

The use of disinfectant pre-soaked wipes (DPW) to decontaminate high-touch environmental surfaces (HTES) by wiping is becoming increasingly widespread in the healthcare environment. However, DPW are rarely tested using conditions simulating their field use, and the label claims of environmental surface disinfectants seldom include wiping action. To evaluate the new E2967-15 standard test specific to wipes, particularly their ability to decontaminate surfaces and to transfer acquired contamination to clean surfaces. ASTM Standard E2967-15 was used by three independent laboratories to test the efficacy of five types of commercially available wipe products. All data generated were pulled together, and reproducibility and repeatability of the standard were measured. All the commercial DPW tested achieved a >4log10 (>99.99%) reduction in colony-forming units (CFU) of Staphylococcus aureus and Acinetobacter baumanii with 10s of wiping, but only one DPW containing 0.5% accelerated H2O2 prevented the transfer of bacteria to another surface. This newly introduced standard method represents a significant advance in assessing DPW for microbial decontamination of HTES, and should greatly assist research and development, and in making more relevant and reliable claims on marketed DPW. Copyright © 2015. Published by Elsevier Ltd.

Experimental Study of Drag Resistance using a Laboratory Scale Rotary Set-Up

DEFF Research Database (Denmark)

Erik Weinell, Claus; Olsen, Kenneth N.; Christoffersen, Martin W.

2003-01-01

This work covers an experimental study of the drag resistance of different painted surfaces and simulated large-scale irregularities, viz. dry spraying, weld seams, barnacle fouling and paint remains. A laboratory scale rotary set-up was used to determine the drag resistance, and the surface...

Novel experimental methodology for the characterization of thermodynamic performance of advanced working pairs for adsorptive heat transformers

International Nuclear Information System (INIS)

Frazzica, Andrea; Sapienza, Alessio; Freni, Angelo

2014-01-01

This paper presents a novel experimental protocol for the evaluation of the thermodynamic performance of working pairs for application in adsorption heat pumps and chillers. The proposed approach is based on the experimental measurements of the main thermo-physical parameters of adsorbent pairs, by means of a DSC/TG apparatus modified to work under saturated vapour conditions, able to measure the ads-/desorption isobars and heat flux as well as the adsorbent specific heat under real boundary conditions. Such kind of activity allows to characterize the thermodynamic performance of an adsorbent pair allowing the estimation of the thermal Coefficient Of Performance (COP) both for heating and cooling applications, only relying on experimental values. The experimental uncertainty of the method has been estimated to be around 2%, for the COP evaluation. In order to validate the proposed procedure, a first test campaign has been carried out on the commercial adsorbent material, AQSOA-Z02, produced by MPI (Mitsubishi Plastics Inc.), while water was used as refrigerant. The proposed experimental methodology will be applied on several other adsorbent materials, either already on the market or still under investigation, in order to get an easy and reliable method to compare thermodynamic performance of adsorptive working pairs

Solar Passive Modification Increase Radiation Safety Standards Inside Accelerator Building

International Nuclear Information System (INIS)

Eid, A. F.; Keshk, A. B.

2010-01-01

Irradiation processing by accelerated electrons is considering one of the most important and useful industrial irradiation treatments. It is depending on two principle attachment elements which are architecture of irradiation building and the accelerator characteristic that was arranged inside irradiation building. Negative environmental measurements were recorded inside the main building and were exceeded the international standards (humidity, air speed, high thermal effects and ozone concentration). The study showed that it is essential to improve the natural environmental standards inside the main irradiation building in order to improve the work environment and to reduce ozone concentration from 220 ppb to international standard. The main goals and advantages were achieved by using environmental architecture (desert architecture) indoor the irradiation building. The work depends on passive solar system which is economic, same architectural elements, comfort / health, and radiation safety, and without mechanical means. The experimental work was accomplished under these modifications. The registered results of various environmental concentrations have proved their normal standards.

Experimental and theoretical study on transition boiling concerning downward-facing horizontal surface in confined space

International Nuclear Information System (INIS)

Zhao, D.W.; Su, G.H.; Tian, W.X.; Sugiyama, K.; Qiu, S.Z.

2008-01-01

Experimental study has been conducted to examine the pool boiling occurs on a relative large downward-facing round surface with a diameter of 300 mm in confined water pool at atmospheric pressure. An artificial neural network (ANN) has been trained successfully based on the experimental data for predicting Nusselt number of transition boiling in the present study. The input parameters of the ANN are wall superheat, ΔT w , the ratio of the gap size to the diameter of the heated surface, δ/D, Prandtl number and Rayleigh number. The output is Nusselt number, Nu. The results show that: Nu decreases with increasing ΔT w , and increases generally with an increase of δ/D. Nu increases with increasing Pr when gap size is smaller than 4.0 mm. And Nu decreases initially and then increases with increasing Pr as gap size bigger than 5.0 mm. The results also indicate that the influence of Grashof number, Gr, could be negligible. Finally, a new correlation was proposed to predict the transition boiling heat transfer under the present condition. The comparisons between the prediction of the new correlation and experimental data show a reasonable agreement

40 CFR 63.7925 - What emissions limitations and work practice standards must I meet for closed vent systems and...

Science.gov (United States)

2010-07-01

... What emissions limitations and work practice standards must I meet for closed vent systems and control... 40 Protection of Environment 13 2010-07-01 2010-07-01 false What emissions limitations and work practice standards must I meet for closed vent systems and control devices? 63.7925 Section 63.7925...

Working with standards

DEFF Research Database (Denmark)

Grosen, Sidsel Lond

2014-01-01

Taking recent developments in the financial sector as its point of departure, this article examines how bank advisors are positioned. Increased complexity in banking products and the risk orientation that has followed the financial crisis make demands on the quality of advice. Drawing...... on qualitative interview studies in two Danish banks, the article questions whether the dominant understanding of bank advisors as primarily sales persons comprises their current positioning. Contradictory demands on bank advisors emerge in the simultaneous emphasis on advisory aspects of the work...

ITER [International Thermonuclear Experimental Reactor] shield and blanket work package report

International Nuclear Information System (INIS)

1988-06-01

This report summarizes nuclear-related work in support of the US effort for the International Thermonuclear Experimental Reactor (ITER) Study. The purpose of this work was to prepare for the first international ITER workshop devoted to defining a basic ITER concept that will serve as a basis for an indepth conceptual design activity over the next 2-1/2 years. Primary tasks carried out during the past year included: design improvements of the inboard shield developed for the TIBER concept, scoping studies of a variety of tritium breeding blanket options, development of necessary design guidelines and evaluation criteria for the blanket options, further safety considerations related to nuclear components and issues regarding structural materials for an ITER device. 44 refs., 31 figs., 29 tabs

Experimental Study of gas-liquid two-phase flow affected by wall surface wettability

International Nuclear Information System (INIS)

Takamasa, T.; Hazuku, T.; Hibiki, T.

2008-01-01

To evaluate the effect of wall surface wettability on the characteristics of upward gas-liquid two-phase flow in a vertical pipe, an experimental study was performed using three test pipes: an acrylic pipe, a hydrophilic pipe and a hydrophobic pipe. Basic flow characteristics such as flow patterns, pressure drop and void fraction were measured in these three pipes. In the hydrophilic pipe, a slug to churn flow transition boundary was shifted to a higher gas velocity at a given liquid velocity, whereas a churn to annular flow transition boundary was shifted to a lower gas velocity at a given liquid velocity. In the hydrophobic pipe, an inverted-churn flow regime was observed in the region where the churn flow regime was observed in the acrylic pipe, while a droplet flow regime was observed in the region where an annular flow regime was observed in the acrylic pipe. At a high gas flow rate, the mean void fraction in the hydrophobic pipe was higher than in the acrylic pipe. The effect of surface wettability on frictional pressure loss was confirmed to be insignificant under the present experimental conditions

Experimental apparatus to investigate interactions of low energy ions with solid surfaces, 1

International Nuclear Information System (INIS)

Tsukakoshi, Osamu; Narusawa, Tadashi; Mizuno, Masayasu; Sone, Kazuho; Ohtsuka, Hidewo.

1975-12-01

Experimental apparatus to study the surface phenomena has been designed, which is intended to solve the vacuum wall problems in future thermonuclear fusion reactors and large experimental tokamak devices. An ion source and the beam transport optics are provided for bombarding solid target surface with an ion beam of energy from 0.1 to 6 keV. Measuring instruments include an ion energy analyser, a quadrupole mass spectrometer, an Auger electron spectrometer, an electro-micro-balance, a neutral particle energy spectrometer and its calibration system. Pumping system consists of oil-free ultrahigh vacuum pumps. Various kinds of experiments will be carried out by using the apparatus: 1) sputtering by low energy ion bombardment, 2) re-emission of the incident particles during and after ion bombardment, 3) release of adsorbed and occluded gases in the solids by ion bombardment, and 4) backscattering of fast ions. The combinations of measuring instruments for each experiment and their relative positions in the vacuum chamber are described through detailed drawings. The fundamental aspect in design of the ion beam transport optics for a low energy ion beam which can no longer neglect the space charge effect is also discussed. (auth.)

A Novel Experimental Set-Up for Improving the Sensitivity of SV Waves to Shallow Surface-Breaking Cracks

Energy Technology Data Exchange (ETDEWEB)

Pecorari, Claudio [Royal Inst. of Technology, Stockholm (Sweden). Dept. of Aeronautical and Vehicle Engineering

2006-03-15

Conventional inspection procedures to detect surface-breaking defects in train axels and thick pipes often employ 45-degree incidence shear vertical (SV) waves as probing tool. Recently obtained theoretical and experimental results indicate that this method is considerably less sensitivity to shallow surface-breaking defects, than the one in which the angle of incidence is selected to be close to the critical angle of the longitudinal wave. This project has confirmed this thesis by experimentally investigating the backscattering of SV waves by surface-breaking cracks as a function o t the angle of incidence. To this end, three cracks of depth approximately equal to 0.3 mm, 0.5 mm and 0.7 were introduced on the surface of steel samples with a thickness of 47 mm. These cracks were insonified with transducers operating at 2.25 MHz, 3.5 MHz, and 5 MHz, which correspond to wavelengths in steel of 1.38 mm, 0.88 mm, and 0.62 mm, respectively. The increase in sensitivity has been assessed in the order of 15 dB.

Study on surface defect structures of ZrO2 and some doped ZrO2 by means of work function measurement

International Nuclear Information System (INIS)

Yamawaki, M.; Suzuki, A.; Ono, F.; Yamaguchi, K.

1997-01-01

The work function change of the ZrO 2 +2%Y 2 O 3 sintered pellet, caused by a change of the composition of the sweep gas, was measured using a high temperature Kelvin probe. The Pt reference electrode was calibrated by using ZrO 2 +2%Y 2 O 3 as a standard material. Work function changes of undoped ZrO 2 and Nb-doped ZrO 2 (2%Nb 2 O 5 ) were measured as a function of equilibrium oxygen partial pressure, P O 2 . The thus obtained exponents of P O 2 , 1/n, were 1/6.2 and 1/33.6 for ZrO 2 and ZrO 2 +2%Nb 2 O 5 , respectively. These exponent values were discussed in terms of defect chemistry of the surface layer. (orig.)

Standard practice for qualification of journeyman painters for application of coatings to steel surfaces of safety-related areas in nuclear facilities

International Nuclear Information System (INIS)

Anon.

1984-01-01

This practice provides a standard qualifying method for journeyman painters to verify their proficiency and ability to attain the required quality for application of specified coatings to steel surfaces in safety-related areas in a nuclear facility. Variations or simplifications of the practice set forth herein may be appropriate for special coating work such as maintenance or qualifications of equipment suppliers shop personnel. It is not the intent of this practice to mandate a singular basis for all qualifications. Evaluation of the journeyman painter being qualified in accordance with this practice, shall be by qualified agents as specified in 4.1. Reports shall be prepared as specified in Section 5, and certification as specified in Section 6. It is the intent of this practice to judge only the ability of the journeyman painter to apply specified coatings with the proper tools and equipment. This standard may involve hazardous materials, operations, and equipment

Experimental study of micro-milling mechanism and surface quality of a nickel-based single crystal superalloy

Energy Technology Data Exchange (ETDEWEB)

Gao, Qi; Gong, Yadong; Zhou, Yun Guang; Wen, Xue Long [School of Mechanical Engineering and Automation, Northeastern University, Shenyang (China)

2017-01-15

Micro-milling is widely used as a method for machining of micro-parts with high precision and efficiency. Taking the nickel-based single-crystal superalloy DD98 as the research object, the crystal characteristics of single-crystal materials were analysed, and the removal mechanism of single-crystal micro-milled parts was described. Based on molecular dynamics, a simulation model for nickel-based single-crystal superalloy DD98 micro-milling was established. Based on the response surface method of central composite design, the influences of spindle speed, feed rate, and milling depth on the surface roughness were examined, and a second-order regression model of the DD98 surface roughness was established. Using analysis of variance and the residuals of the model, a significant influence on surface roughness was found in the following order from large to small: Feed rate, spindle speed, and milling depth. Comparisons were conducted between the micro-milling experimental values and the predicted model values for different process parameters. The results show that the model fit is relatively high, and the adaptability is good. Scanning electron microscopy analysis of the micro-milling surfaces was performed to verify the slip and the removal mechanism of single-crystal materials. These results offer a theoretical reference and experimental basis for micro-milling of single-crystal materials.

The electronic work function of the different faces of tungsten

International Nuclear Information System (INIS)

Modinos, A.

1978-01-01

A semi-empirical theory of the electronic work function of the different faces of tungsten is presented. All the parameters entering the theory, except one, are estimated independently. The one adjustable parameter relates to the isotropic contribution to the work function, and, can, in principle, be determined from a self-consistent calculation of the band-structure of the energy levels in the bulk of the metal. The calculated values for the work function are in reasonably good agreement with available experimental data for practically all of the crystallographic planes with the exception of the (100) plane. For the latter, the calculated value is 0.3 eV above the experimental value. It is suggested that a negative contribution to the surface dipole potential from surface states, that exist on this plane, may be the reason of this discrepancy. (Auth.)

A non-invasive experimental approach for surface temperature measurements on semi-crystalline thermoplastics

Science.gov (United States)

Boztepe, Sinan; Gilblas, Remi; de Almeida, Olivier; Le Maoult, Yannick; Schmidt, Fabrice

2017-10-01

Most of the thermoforming processes of thermoplastic polymers and their composites are performed adopting a combined heating and forming stages at which a precursor is heated prior to the forming. This step is done in order to improve formability by softening the thermoplastic polymer. Due to low thermal conductivity and semi-transparency of polymers, infrared (IR) heating is widely used for thermoforming of such materials. Predictive radiation heat transfer models for temperature distributions are therefore critical for optimizations of thermoforming process. One of the key challenges is to build a predictive model including the physical background of radiation heat transfer phenomenon in semi-crystalline thermoplastics as their microcrystalline structure introduces an optically heterogeneous medium. In addition, the accuracy of a predictive model is required to be validated experimentally where IR thermography is one of the suitable methods for such a validation as it provides a non-invasive, full-field surface temperature measurement. Although IR cameras provide a non-invasive measurement, a key issue for obtaining a reliable measurement depends on the optical characteristics of a heated material and the operating spectral band of IR camera. It is desired that the surface of a material to be measured has a spectral band where the material behaves opaque and an employed IR camera operates in the corresponding band. In this study, the optical characteristics of the PO-based polymer are discussed and, an experimental approach is proposed in order to measure the surface temperature of the PO-based polymer via IR thermography. The preliminary analyses showed that IR thermographic measurements may not be simply performed on PO-based polymers and require a correction method as their semi-transparent medium introduce a challenge to obtain reliable surface temperature measurements.

The structure of a working catalyst : from flat surfaces to nanoparticles

NARCIS (Netherlands)

Roobol, Sander Bas

2014-01-01

Catalysis is the working horse of the chemical industry. In many cases, it is a poorly understood process taking place at the surfaces of nanoparticles under relatively harsh conditions, such as high pressures and high temperatures. This thesis focuses on new approaches to acquire atomic-scale

Experimental and numerical modelling of surface water-groundwater flow and pollution interactions under tidal forcing

Science.gov (United States)

Spanoudaki, Katerina; Bockelmann-Evans, Bettina; Schaefer, Florian; Kampanis, Nikolaos; Nanou-Giannarou, Aikaterini; Stamou, Anastasios; Falconer, Roger

2015-04-01

Surface water and groundwater are integral components of the hydrologic continuum and the interaction between them affects both their quantity and quality. However, surface water and groundwater are often considered as two separate systems and are analysed independently. This separation is partly due to the different time scales, which apply in surface water and groundwater flows and partly due to the difficulties in measuring and modelling their interactions (Winter et al., 1998). Coastal areas in particular are a difficult hydrologic environment to represent with a mathematical model due to the large number of contributing hydrologic processes. Accurate prediction of interactions between coastal waters, groundwater and neighbouring wetlands, for example, requires the use of integrated surface water-groundwater models. In the past few decades a large number of mathematical models and field methods have been developed in order to quantify the interaction between groundwater and hydraulically connected surface water bodies. Field studies may provide the best data (Hughes, 1995) but are usually expensive and involve too many parameters. In addition, the interpretation of field measurements and linking with modelling tools often proves to be difficult. In contrast, experimental studies are less expensive and provide controlled data. However, experimental studies of surface water-groundwater interaction are less frequently encountered in the literature than filed studies (e.g. Ebrahimi et al., 2007; Kuan et al., 2012; Sparks et al., 2013). To this end, an experimental model has been constructed at the Hyder Hydraulics Laboratory at Cardiff University to enable measurements to be made of groundwater transport through a sand embankment between a tidal water body such as an estuary and a non-tidal water body such as a wetland. The transport behaviour of a conservative tracer was studied for a constant water level on the wetland side of the embankment, while running a

Analysis of the basic professional standards involving the work of psychologists in difficult and legally significant situations

Directory of Open Access Journals (Sweden)

Bogdanovich N. V.

2016-06-01

Full Text Available In this article the analysis of professional standards in terms of the scope of work of the psychologist with clients in difficult life and legal situations. The criteria of analysis chosen: reflected in professional activities, the choice of grounds for the selection of professional activities that focus on a specific Department, selection of a particular direction of activity of the psychologist (prevention, support, rehabilitation. It is shown that all five of the analyzed standards imply such a situation, but only three of them ("educational psychologist", "Psychologist in the social sphere", "Specialist in rehabilitative work in the social sphere" describe the activities of the psychologist, and the remaining ("Expert of bodies of guardianship and guardianship concerning minors" and "Specialist in working with families" are more organizational in nature. The conclusion about compliance of the training programs developed by the Department of legal psychology and law and education, the requirements of professional standards, proposed improvements in these programs.

Influence of Surface Position along the Working Range of Conoscopic Holography Sensors on Dimensional Verification of AISI 316 Wire EDM Machined Surfaces

Directory of Open Access Journals (Sweden)

Pedro Fernández

2014-03-01

Full Text Available Conoscopic holography (CH is a non-contact interferometric technique used for surface digitization which presents several advantages over other optical techniques such as laser triangulation. Among others, the ability for the reconstruction of high-sloped surfaces stands out, and so does its lower dependence on surface optical properties. Nevertheless, similarly to other optical systems, adjustment of CH sensors requires an adequate selection of configuration parameters for ensuring a high quality surface digitizing. This should be done on a surface located as close as possible to the stand-off distance by tuning frequency (F and power (P until the quality indicators Signal-to-Noise Ratio (SNR and signal envelope (Total meet proper values. However, not all the points of an actual surface are located at the stand-off distance, but they could be located throughout the whole working range (WR. Thus, the quality of a digitized surface may not be uniform. The present work analyses how the quality of a reconstructed surface is affected by its relative position within the WR under different combinations of the parameters F and P. Experiments have been conducted on AISI 316 wire EDM machined flat surfaces. The number of high-quality points digitized as well as distance measurements between different surfaces throughout the WR allowed for comparing the metrological behaviour of the CH sensor with respect to a touch probe (TP on a CMM.

Dithiocarbamate Self-Assembled Monolayers as Efficient Surface Modifiers for Low Work Function Noble Metals

Energy Technology Data Exchange (ETDEWEB)

Meyer, Dominik; Schäfer, Tobias; Schulz, Philip; Jung, Sebastian; Rittich, Julia; Mokros, Daniel; Segger, Ingolf; Maercks, Franziska; Effertz, Christian; Mazzarello, Riccardo; Wuttig, Matthias

2016-09-06

Tuning the work function of the electrode is one of the crucial steps to improve charge extraction in organic electronic devices. Here, we show that N,N-dialkyl dithiocarbamates (DTC) can be effectively employed to produce low work function noble metal electrodes. Work functions between 3.1 and 3.5 eV are observed for all metals investigated (Cu, Ag, and Au). Ultraviolet photoemission spectroscopy (UPS) reveals a maximum decrease in work function by 2.1 eV as compared to the bare metal surface. Electronic structure calculations elucidate how the complex interplay between intrinsic dipoles and dipoles induced by bond formation generates such large work function shifts. Subsequently, we quantify the improvement in contact resistance of organic thin film transistor devices with DTC coated source and drain electrodes. These findings demonstrate that DTC molecules can be employed as universal surface modifiers to produce stable electrodes for electron injection in high performance hybrid organic optoelectronics.

Nuclear data standards - International Evaluation Co-operation volume 7

International Nuclear Information System (INIS)

Carlson, A.D.; Shibata, K.; Vonach, H.; Hambsch, F.J.; Chen, Z.; Hofmann, H.M.; Oh, S.Y.; Badikov, S.A.; Gai, E.V.; Pronyaev, V.G.; Smith, D.L.; Hale, G.M.; Kawano, T.; Larson, N.M.

2006-01-01

A Working Party on International Evaluation Co-operation was established under the sponsorship of the OECD/NEA Nuclear Science Committee (NSC) to promote the exchange of information on nuclear data evaluations, validation and related topics. Its aim is also to provide a framework for co-operative activities between members of the major nuclear data evaluation projects. This includes the possible exchange of scientists in order to encourage co-operation. Requirements for experimental data resulting from this activity are compiled. The working party determines common criteria for evaluated nuclear data files with a view to assessing and improving the quality and completeness of evaluated data. The parties to the project are: ENDF (United States), JEFF/EFF (NEA Data Bank member countries) and JENDL (Japan). Co-operation with evaluation projects of non-OECD countries is organised through the Nuclear Data Section of the International Atomic Energy Agency (IAEA). This report was issued by Subgroup 7, which was in charge of producing new evaluated neutron cross-section standards. When starting the project, there was a general consensus on the need to update these standards, as significant improvements had been made to the experimental database since 1991 when the last evaluation of these standards was performed. The present work was accomplished through efficient collaboration between a task force of the US Cross-section Evaluation Working Group (CSEWG), a Co-ordinated Research Project (CRP) of the International Atomic Energy Agency (IAEA) and Subgroup 7 of the Working Party on International Evaluation Co-operation (WPEC) of the NEA Nuclear Science Committee. Work is reported on the results of an international effort to evaluate the neutron cross-section standards. The evaluations include the H(n,n), 6 Li(n,t), 10 B(n,α), 10 B(n,α1γ), 197 Au(n,γ), 235 U(n,f) and 238 U(n,f) standard reactions. Evaluations were also produced for the non-standard 238 U(n,γ) and 239 Pu

Lattice Gauge Theories Within and Beyond the Standard Model

Energy Technology Data Exchange (ETDEWEB)

Gelzer, Zechariah John [Iowa U.

2017-01-01

The Standard Model of particle physics has been very successful in describing fundamental interactions up to the highest energies currently probed in particle accelerator experiments. However, the Standard Model is incomplete and currently exhibits tension with experimental data for interactions involving $B$~mesons. Consequently, $B$-meson physics is of great interest to both experimentalists and theorists. Experimentalists worldwide are studying the decay and mixing processes of $B$~mesons in particle accelerators. Theorists are working to understand the data by employing lattice gauge theories within and beyond the Standard Model. This work addresses the theoretical effort and is divided into two main parts. In the first part, I present a lattice-QCD calculation of form factors for exclusive semileptonic decays of $B$~mesons that are mediated by both charged currents ($B \\to \\pi \\ell \

Thermodynamics and structure of liquid surfaces investigated directly with surface analytical tools

Energy Technology Data Exchange (ETDEWEB)

Andersson, Gunther [Flinders Univ., Adelaide, SA (Australia). Centre for NanoScale Science and Technology; Morgner, Harald [Leipzig Univ. (Germany). Wilhelm Ostwald Inst. for Physical and Theoretical Chemistry

2017-06-15

Measuring directly the composition, the distribution of constituents as function of the depth and the orientation of molecules at liquid surfaces is essential for determining physicochemical properties of liquid surfaces. While the experimental tools that have been developed for analyzing solid surfaces can in principal be applied to liquid surfaces, it turned out that they had to be adjusted to the particular challenges imposed by liquid samples, e.g. by the unavoidable vapor pressure and by the mobility of the constituting atoms/molecules. In the present work it is shown, how electron spectroscopy and ion scattering spectroscopy have been used for analyzing liquid surfaces. The emphasis of this review is on using the structural information gained for determining the physicochemical properties of liquid surfaces. (copyright 2017 by WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Reference sources for the calibration of surface contamination monitors - Beta-emitters (maximum beta energy greater than MeV) and alpha-emitters (International Standard Publication ISO 8769:1988)

International Nuclear Information System (INIS)

Stefanik, J.

2001-01-01

This International Standard specifies the characteristics of reference sources of radioactive surface contamination, traceable to national measurement standards, for the calibration of surface contamination monitors. This International Standard relates to alpha-emitters and to beta-emitters of maximum beta energy greater than 0,15 MeV. It does not describe the procedures involved in the use of these reference sources for the calibration of surface contamination monitors. Such procedures are specified in IEC Publication 325 and other documents. This International Standard specifies reference radiations for the calibration of surface contamination monitors which take the form of adequately characterized large area sources specified, without exception, in terms of activity and surface emission rate, the evaluation of these quantities being traceable to national standards

Microbiological quality control of single-walled carbon-nanotubes-coated surfaces experimentally contaminated

International Nuclear Information System (INIS)

Natalizi, T.; Frioni, A.; Passeri, D.; Pantanella, F.

2013-01-01

The emergence of new nanotechnologies involves the spreading of nanoparticles in various fields of human life. Nanoparticles in general and, more specifically, carbon nanotubes have been adopted for many practical approaches i.e.: coatings for medical devices, food process industry and drug delivery. Humans will be increasingly exposed to nanoparticles but the susceptibility of nanostructured materials to microbial colonization in process of manufacturing and storage has not been thoroughly considered. Therefore, the microbiological quality control of nanoparticles plays a pivotal role. Different analytical methods have been attempted for detecting bacterial population contaminating a surface, but no one can be considered fully appropriate. Here, BioTimer Assay (BTA) and conventional sonication followed by colony forming units method (S-CFU) were applied for microbiological quality control of single-walled carbon nanotubes (SWCNTs)-coated surfaces experimentally contaminated with Streptococcus mutans and Pseudomonas aeruginosa. Our results demonstrated that S-CFU is unreliable to actually determine the number of bacteria, contaminating abiotic surfaces, as it does not detach all adherent bacteria and kills part of the bacterial population. Instead, BTA is a reliable method to enumerate bacteria colonizing SWCNTs-coated surfaces and can be considered a useful tool for microbiological quality control of nanomaterials for human use.

An experimental study on mass loading of soil particles on plant surfaces

International Nuclear Information System (INIS)

Li, J.; Gerzabek, M.H.; Mueck, K.

1994-03-01

Radionuclide contaminated soil adhered to plant surfaces can contribute to human ingestion dose. To determine this contribution, a method of 46 Sc neutron activation analysis was established and tested, by which a detection limit of 0.05 mg soil per g dry plant biomass can be obtained. In the field and greenhouse experiment the mass loading of soil on ryegrass (Lolium perenne L.) and broad bean (Vicia faba L.) was investigated and the contribution from rainsplash and wind erosion were evaluated separately. Soil retained on plant surfaces in field conditions in Seibersdorf/Austria was 5.77 ± 1.44 mg soil per g dry plant for ryegrass and 9.51 ± 0.73 mg soil per g dry plant for broad bean. Estimates of contribution from rainsplash and wind erosion to soil contamination of plant during the experimental period are 68 % and 32 % for broadbean, 47 % and 53 % for ryegrass, respectively. Mass loading results from field studies indicate that soil adhesion on plant surfaces can contribute up to 23 % of plant 137 Cs contamination, the transfer factors modified by mass loading decline differently, depending on 137 Cs concentration of the soil and the soil mass adhered to plant surfaces. (authors)

An Experimental Study on the Pool Boiling Heat Transfer on a Square Surface

International Nuclear Information System (INIS)

Kim, Jae Kwang

2000-02-01

An experimental study was carried out to identify the various regimes of natural convective boiling and to determine the Critical Heat Flux (CHF) on a square surface. The basic knowledge on the boiling heat transfer and CHF on the square surface is necessary for various engineering problems, such as the design of compact heat exchangers, cooling of CPU chips, and design of the external cooling mechanism for the reactor during the severe accidents in the nuclear power plants. The heater block made of copper with cartridge heaters in it is submerged in a water tank with windows for visualization. The heater surface has dimension of 70mm x 70mm and the maximum heat flux capacity is about 1.8MW/m 2 . The boiling heat transfer coefficient for the various flow regimes up to CHF has been measured for upward facing surface, vertical surface, and nearly horizontal downward facing surfaces. The temperatures of the heater block are measured by the thermocouples imbedded in the heater block. As the heat flux increases from 100kW/m 2 to 1.0MW/m 2 , the heat-transfer regime changes from the nucleate boiling to the CHF. Near 1.0MW/m 2 , the heat transfer regime suddenly changed from nucleate boiling to film boiling and it resulted in a rapid heat up of the heater block. The various boiling patterns on the vertical surface, upward facing surface, and downward facing surface are observed by a high speed video camera whose frame rate is 1000fps. An explosive vapor generation on the heated surface, whose size and frequency are characterized by the heat flux and inclination angle, is observed

20 CFR 667.274 - What health and safety standards apply to the working conditions of participants in activities...

Science.gov (United States)

2010-04-01

... and safety standards apply to the working conditions of participants in activities under title I of... working conditions of participants in activities under title I of WIA? 667.274 Section 667.274 Employees... working conditions of employees are equally applicable to working conditions of participants engaged in...

An experimental method to determine the electrostatic field enhancement factor of a practical conductor surface

DEFF Research Database (Denmark)

McAllister, Iain Wilson; Crichton, George C

1989-01-01

A method of determining the field enhancement factor of a practical conductor is presented. The method is developed from a modified theory of discharge onset in a gaseous medium. This modification incorporates the influence of conductor surface roughness. Onset data from an experimental study...

Protein folding: Defining a standard set of experimental conditions and a preliminary kinetic data set of two-state proteins

DEFF Research Database (Denmark)

Maxwell, Karen L.; Wildes, D.; Zarrine-Afsar, A.

2005-01-01

Recent years have seen the publication of both empirical and theoretical relationships predicting the rates with which proteins fold. Our ability to test and refine these relationships has been limited, however, by a variety of difficulties associated with the comparison of folding and unfolding ...... efforts is to set uniform standards for the experimental community and to initiate an accumulating, self-consistent data set that will aid ongoing efforts to understand the folding process....... constructs. The lack of a single approach to data analysis and error estimation, or even of a common set of units and reporting standards, further hinders comparative studies of folding. In an effort to overcome these problems, we define here a consensus set of experimental conditions (25°C at pH 7.0, 50 m...... rates, thermodynamics, and structure across diverse sets of proteins. These difficulties include the wide, potentially confounding range of experimental conditions and methods employed to date and the difficulty of obtaining correct and complete sequence and structural details for the characterized...

Experimental and numerical investigation of liquid jet impingement on superhydrophobic and hydrophobic convex surfaces

International Nuclear Information System (INIS)

Kibar, Ali

2017-01-01

Experiments and numerical simulations were carried out to examine the vertical impingement a round liquid jet on the edges of horizontal convex surfaces that were either superhydrophobic or hydrophobic. The experiments examine the effects on the flow behaviour of curvature, wettability, inertia of the jet, and the impingement rate. Three copper pipes with outer diameters of 15, 22, and 35 mm were investigated. The pipes were wrapped with a piece of a Brassica oleracea leaf or a smooth Teflon sheet, which have apparent contact angles of 160° and 113°. The Reynolds number ranged from 1000 to 4500, and the impingement rates of the liquid jets were varied. Numerical results show good agreement with the experimental results for explaining flow and provide detailed information about the impingement on the surfaces. The liquid jet reflected off the superhydrophobic surfaces for all conditions. However, the jet reflected or deflected off the hydrophobic surface, depending on the inertia of the jet, the curvature of the surface, and the impingement rate. The results suggest that pressure is not the main reason for the bending of the jet around the curved hydrophobic surface. (paper)

Experimental and numerical investigation of liquid jet impingement on superhydrophobic and hydrophobic convex surfaces

Energy Technology Data Exchange (ETDEWEB)

Kibar, Ali, E-mail: alikibar@kocaeli.edu.tr [Department of Mechanical and Material Technologies, Kocaeli University, Arslanbey Campus, 41285, Kocaeli (Turkey)

2017-02-15

Experiments and numerical simulations were carried out to examine the vertical impingement a round liquid jet on the edges of horizontal convex surfaces that were either superhydrophobic or hydrophobic. The experiments examine the effects on the flow behaviour of curvature, wettability, inertia of the jet, and the impingement rate. Three copper pipes with outer diameters of 15, 22, and 35 mm were investigated. The pipes were wrapped with a piece of a Brassica oleracea leaf or a smooth Teflon sheet, which have apparent contact angles of 160° and 113°. The Reynolds number ranged from 1000 to 4500, and the impingement rates of the liquid jets were varied. Numerical results show good agreement with the experimental results for explaining flow and provide detailed information about the impingement on the surfaces. The liquid jet reflected off the superhydrophobic surfaces for all conditions. However, the jet reflected or deflected off the hydrophobic surface, depending on the inertia of the jet, the curvature of the surface, and the impingement rate. The results suggest that pressure is not the main reason for the bending of the jet around the curved hydrophobic surface. (paper)

Assessing the cleanliness of surfaces: Innovative molecular approaches vs. standard spore assays

Energy Technology Data Exchange (ETDEWEB)

Cooper, M.; Duc, M.T. La; Probst, A.; Vaishampayan, P.; Stam, C.; Benardini, J.N.; Piceno, Y.M.; Andersen, G.L.; Venkateswaran, K.

2011-04-01

A bacterial spore assay and a molecular DNA microarray method were compared for their ability to assess relative cleanliness in the context of bacterial abundance and diversity on spacecraft surfaces. Colony counts derived from the NASA standard spore assay were extremely low for spacecraft surfaces. However, the PhyloChip generation 3 (G3) DNA microarray resolved the genetic signatures of a highly diverse suite of microorganisms in the very same sample set. Samples completely devoid of cultivable spores were shown to harbor the DNA of more than 100 distinct microbial phylotypes. Furthermore, samples with higher numbers of cultivable spores did not necessarily give rise to a greater microbial diversity upon analysis with the DNA microarray. The findings of this study clearly demonstrated that there is not a statistically significant correlation between the cultivable spore counts obtained from a sample and the degree of bacterial diversity present. Based on these results, it can be stated that validated state-of-the-art molecular techniques, such as DNA microarrays, can be utilized in parallel with classical culture-based methods to further describe the cleanliness of spacecraft surfaces.

Experimental technique of small angle neutron scattering

International Nuclear Information System (INIS)

Xia Qingzhong; Chen Bo

2006-03-01

The main parts of Small Angle Neutron Scattering (SANS) spectrometer, and their function and different parameters are introduced from experimental aspect. Detailed information is also introduced for SANS spectrometer 'Membrana-2'. Based on practical experiments, the fundamental requirements and working condition for SANS experiments, including sample preparation, detector calibration, standard sample selection and data preliminary process are described. (authors)

Precision of working memory for visual motion sequences and transparent motion surfaces.

Science.gov (United States)

Zokaei, Nahid; Gorgoraptis, Nikos; Bahrami, Bahador; Bays, Paul M; Husain, Masud

2011-12-01

Recent studies investigating working memory for location, color, and orientation support a dynamic resource model. We examined whether this might also apply to motion, using random dot kinematograms (RDKs) presented sequentially or simultaneously. Mean precision for motion direction declined as sequence length increased, with precision being lower for earlier RDKs. Two alternative models of working memory were compared specifically to distinguish between the contributions of different sources of error that corrupt memory (W. Zhang & S. J. Luck, 2008 vs. P. M. Bays, R. F. G. Catalao, & M. Husain, 2009). The latter provided a significantly better fit for the data, revealing that decrease in memory precision for earlier items is explained by an increase in interference from other items in a sequence rather than random guessing or a temporal decay of information. Misbinding feature attributes is an important source of error in working memory. Precision of memory for motion direction decreased when two RDKs were presented simultaneously as transparent surfaces, compared to sequential RDKs. However, precision was enhanced when one motion surface was prioritized, demonstrating that selective attention can improve recall precision. These results are consistent with a resource model that can be used as a general conceptual framework for understanding working memory across a range of visual features.

Some experimental data on accommodation coefficients for the noble ions on metal surfaces

International Nuclear Information System (INIS)

Gusev, K.I.; Rijov, Y.A.; Shkarban, I.I.

1974-01-01

Methods and results of experimental measurements of energy accommodation for Ar + , Kr + , and Xe + ions with initial energy E 0 - 100-500eV bombarding Cu, Mo, Ag and other (including Mo - monocrystal) foil target are presented. The angular dependencies for the energy accommodation coefficient are obtained within the range of angle phi=0+70 deg (phi is the angle between the target surface normal and the beam direction)

Investigation of Surface Treatments to Improve the Friction and Wear of Titanium Alloys for Diesel Engine Components

Energy Technology Data Exchange (ETDEWEB)

Blau, Peter J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Cooley, Kevin M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Kirkham, Melanie J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Bansal, Dinesh G. [Oak Ridge Associated Universities, TN (United States)

2012-09-20

This final report summarizes experimental and analytical work performed under an agreement between the U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Office of Transportation Technologies, and UT-Battelle LLC. The project was directed by Jerry Gibbs, of the U.S. Department of Energy’s Propulsion Materials Program, with management by D. P. Stinton and J. A. Haynes of ORNL. Participants included Peter J. Blau (Principal Investigator), Kevin M. Cooley (senior technician), Melanie J. Kirkham (materials scientist) of the Materials Science and Technology Division or ORNL, and Dinesh G. Bansal, a post doctoral fellow employed by Oak Ridge Associated Universities (ORAU) and who, at the time of this writing, is an engineer with Cummins, Inc. This report covers a three-year effort that involved two stages. In the first stage, and after a review of the literature and discussions with surface treatment experts, a series of candidate alloys and surface treatments for titanium alloy (Ti-6Al-4V) was selected for initial screening. After pre-screening using an ASTM standard test method, the more promising surface treatments were tested in Phase 2 using a variable loading apparatus that was designed and built to simulate the changing load patterns in a typical connecting rod bearing. Information on load profiles from the literature was supplemented with the help of T.C. Chen and Howard Savage of Cummins, Inc. Considering the dynamic and evolving nature of materials technology, this report presents a snapshot of commercial and experimental bearing surface technologies for titanium alloys that were available during the period of this work. Undoubtedly, further improvements in surface engineering methods for titanium will evolve.

Surface energy of metal alloy nanoparticles

Science.gov (United States)

Takrori, Fahed M.; Ayyad, Ahmed

2017-04-01

The measurement of surface energy of alloy nanoparticles experimentally is still a challenge therefore theoretical work is necessary to estimate its value. In continuation of our previous work on the calculation of the surface energy of pure metallic nanoparticles we have extended our work to calculate the surface energy of different alloy systems, namely, Co-Ni, Au-Cu, Cu-Al, Cu-Mg and Mo-Cs binary alloys. It is shown that the surface energy of metallic binary alloy decreases with decreasing particle size approaching relatively small values at small sizes. When both metals in the alloy obey the Hume-Rothery rules, the difference in the surface energy is small at the macroscopic as well as in the nano-scale. However when the alloy deviated from these rules the difference in surface energy is large in the macroscopic and in the nano scales. Interestingly when solid solution formation is not possible at the macroscopic scale according to the Hume-Rothery rules, it is shown it may form at the nano-scale. To our knowledge these findings here are presented for the first time and is challenging from fundamental as well as technological point of views.

Ab initio work function of elemental metals

DEFF Research Database (Denmark)

Skriver, Hans Lomholt; Rosengaard, N. M.

1992-01-01

We have used a recently developed self-consistent Green’s-function technique based on tight-binding linear-muffin-tin-orbital theory to calculate the work function for the close-packed surfaces of 37 elemental metals. The results agree with the limited experimental data obtained from single cryst...

48 CFR 852.222-70 - Contract Work Hours and Safety Standards Act-nursing home care contract supplement.

Science.gov (United States)

2010-10-01

... Safety Standards Act-nursing home care contract supplement. 852.222-70 Section 852.222-70 Federal...—nursing home care contract supplement. As prescribed in 822.305, for nursing home care requirements, insert the following clause: Contract Work Hours and Safety Standards Act—Nursing Home Care Contract...

An Experimental Comparison of Similarity Assessment Measures for 3D Models on Constrained Surface Deformation

Science.gov (United States)

Quan, Lulin; Yang, Zhixin

2010-05-01

To address the issues in the area of design customization, this paper expressed the specification and application of the constrained surface deformation, and reported the experimental performance comparison of three prevail effective similarity assessment algorithms on constrained surface deformation domain. Constrained surface deformation becomes a promising method that supports for various downstream applications of customized design. Similarity assessment is regarded as the key technology for inspecting the success of new design via measuring the difference level between the deformed new design and the initial sample model, and indicating whether the difference level is within the limitation. According to our theoretical analysis and pre-experiments, three similarity assessment algorithms are suitable for this domain, including shape histogram based method, skeleton based method, and U system moment based method. We analyze their basic functions and implementation methodologies in detail, and do a series of experiments on various situations to test their accuracy and efficiency using precision-recall diagram. Shoe model is chosen as an industrial example for the experiments. It shows that shape histogram based method gained an optimal performance in comparison. Based on the result, we proposed a novel approach that integrating surface constrains and shape histogram description with adaptive weighting method, which emphasize the role of constrains during the assessment. The limited initial experimental result demonstrated that our algorithm outperforms other three algorithms. A clear direction for future development is also drawn at the end of the paper.

Mirror-like slip surfaces in dolostone: natural and experimental constraints on a potential seismic marker

Science.gov (United States)