WorldWideScience

Sample records for surface-bound epoxy groups

  1. Acid-base properties and the chemical imaging of surface-bound functional groups studied with scanning force microscopy

    NARCIS (Netherlands)

    van der Vegte, E.W.; Hadziioannou, G

    1997-01-01

    In this paper we present a scanning force microscopy (SFM) study on electrostatic and hydrogen-bonding interactions between chemically modified SFM probes and surface functional groups. pH-dependent adhesion force measurements in aqueous media between various ionizable functional groups showed a

  2. Surface-bound capsular polysaccharide of type Ia group B Streptococcus mediates C1 binding and activation of the classic complement pathway

    International Nuclear Information System (INIS)

    Levy, N.J.; Kasper, D.L.

    1986-01-01

    The role of surface-bound type Ia group B Streptococcus (GBS) capsular polysaccharide in anti-body-independent binding of C1 and activation of the classic component pathway was investigated. In a radiolabeled bacterial-polymorphonuclear leukocyte (PMN) association assay, a measure of bacterial opsonization, preincubation of 3 H-type Ia GBS with purified F(ab') 2 to the organism blocked the association of the bacteria with PMN', and the inhibitory effect was dose dependent. The specificity of F(ab') 2 blocking was shown after adsorption of F(ab') 2 with type Ia polysaccharide-sensitized erythrocytes. Polysaccharide-adsorbed F(ab') 2 had a 70% decrease in ability to block the association of bacteria with PMN. Neuraminidase digestion removed 80% of the terminal sialic acid residues from the native polysaccharide. These neuraminidase-digested organisms had a 72% decrease in binding and transfer of purified C1 compared with non-enzyme-treated organisms. Type Ia capsular polysaccharide bound to sheep erythrocytes promoted classic complement pathway-mediated hemolysis of the cells. The role of C1 inhibitor (INH) in modulation of C1 activation by the organisms was investigated. The possibility existed that the C1 INH could be bound by the bacteria, allowing C1 activation to occur in the fluid phase. The inhibitor was purified from human serum, and its activity was measured before and after incubation with type Ia GBS. The organisms had no effect on C1 INH activity. Thus surface-bound capsular polysacchardie of type Ia GBS mediates C1 binding and classic pathway activation, and this does not involve the C1 INH

  3. The Electrical Properties for Phenolic Isocyanate-Modified Bisphenol-Based Epoxy Resins Comprising Benzoate Group.

    Science.gov (United States)

    Lee, Eun Yong; Chae, Il Seok; Park, Dongkyung; Suh, Hongsuk; Kang, Sang Wook

    2016-03-01

    Epoxy resin has been required to have a low dielectric constant (D(k)), low dissipation factor (Df), low coefficient of thermal expansion (CTE), low water absorption, high mechanical, and high adhesion properties for various applications. A series of novel phenolic isocyanate-modified bisphenol-based epoxy resins comprising benzoate group were prepared for practical electronic packaging applications. The developed epoxy resins showed highly reduced dielectric constants (D(k)-3.00 at 1 GHz) and low dissipation values (Df-0.014 at 1 GHz) as well as enhanced thermal properties.

  4. Surface-bound states in nanodiamonds

    Science.gov (United States)

    Han, Peng; Antonov, Denis; Wrachtrup, Jörg; Bester, Gabriel

    2017-05-01

    We show via ab initio calculations and an electrostatic model that the notoriously low, but positive, electron affinity of bulk diamond becomes negative for hydrogen passivated nanodiamonds and argue that this peculiar situation (type-II offset with a vacuum level at nearly midgap) and the three further conditions: (i) a surface dipole with positive charge on the outside layer, (ii) a spherical symmetry, and (iii) a dielectric mismatch at the surface, results in the emergence of a peculiar type of surface state localized just outside the nanodiamond. These states are referred to as "surface-bound states" and have consequently a strong environmental sensitivity. These type of states should exist in any nanostructure with negative electron affinity. We further quantify the band offsets of different type of nanostructures as well as the exciton binding energy and contrast the results with results for "conventional" silicon quantum dots.

  5. Diastereoisomeric diversity dictates reactivity of epoxy groups in limonene dioxide polymerization

    Directory of Open Access Journals (Sweden)

    M. Soto

    2018-06-01

    Full Text Available Limonene dioxide (LDO has the potential to find a wide application as a bio-based epoxy resin. Its polymerizations by catalyzed ring-opening, and by polyaddition with diamines were compared with the polymerizations of the commercial epoxy resins bisphenol-A diglycidyl ether (BADGE, and 3,4-epoxycyclohexylmethyl-3′,4′-epoxycyclohexane carboxylate (ECC. Differential scanning calorimetry (DSC studies showed that LDO polymerizations suffer in all cases studied from incomplete conversions. Nuclear magnetic resonance (NMR studies revealed that in cis-isomers of LDO the internal epoxide rings were not reacting. The low reactivity of this epoxide group was explained by mechanistic considerations making use of the Fürst-Plattner rule, or trans-diaxial effect. Due to diastereomeric diversity approximately one-fourth of epoxide groups present in LDO could not react. Therefore, a diastereoselective epoxidation of limonene could provide a fully reactive bio-based epoxy resin.

  6. Polymer Electrolyte Prepared from Highly Deproteinized Natural Rubber Having Epoxy Group

    Science.gov (United States)

    Klinklai, W.; Kawahara, S.; Isono, Y.; Mizumo, T.; Yoshizawa, M.; Ohno, H.

    Deproteinized natural rubber having epoxy group (EDPNR) was applied to transport Li+ as a solid polymer electrolyte. The deproteinized natural rubber, incubated with proteolytic enzyme and surfactant, was subjected to epoxidation followed by oxidative depolymerization in latex stage. The resulting rubber was proved to be a liquid deproteinized natural rubber (LEDPNR) having polar epoxy groups, low Tg, low Mn and well-defined terminal units. Ionic conductivity of LEDPNR mixed with alkali metal salts was investigated through impedance analysis to clarify an effect of proteins present in the rubber. The ionic conductivity of the resulting LEDPNR depended on the kind of salts, their concentrations and temperature. The ionic conductivity of LEDPNR/lithium bis(trifluoromethan sulfonyl)imide (LiTFSI) was higher than that of LEDPNR/ lithium perchlorate (LiClO4). The difference in the ionic conductivity was attributed to the solubility of the salts as results of both high-resolution solid-state 13C-NMR spectroscopy and measurements of spin-lattice relaxation time. The conductivity of LEDPNR/LiTFSI was also dependent upon concentrations of LiTFSI and it reached the highest value at 20 wt%, which was different from the monotonic increase in the Li+ conductivity of liquid epoxidized natural rubber prepared from untreated natural rubber.

  7. Determining the limit of detection of surface bound antibody.

    Science.gov (United States)

    Madiona, Robert M T; Welch, Nicholas G; Scoble, Judith A; Muir, Benjamin W; Pigram, Paul J

    2017-08-11

    Determination of a limit of detection (LoD) for surface bound antibodies is crucial for the development and deployment of sensitive bioassays. The measurement of very low concentrations of surface bound antibodies is also important in the manufacturing of pharmaceutical products such as antibody-conjugated pharmaceuticals. Low concentrations are required to avoid an immune response from the target host. Enzyme-linked immunosorbent assay (ELISA), x-ray photoelectron spectroscopy (XPS), and time-of-flight secondary ion mass spectrometry (ToF-SIMS) were used to determine the LoD for the surface bound antibody (antiepidermal growth factor receptor antibody) on silicon substrates. Antibody solution concentrations between 10 μg/ml and 1 ng/ml and a control (antibody-free buffer solution) were employed, and the detection performance of each technique was compared. For this system, the ELISA LoD was 100 ng/ml and the XPS LoD was 1 μg/ml, corresponding to an estimated surface concentration of 49  ± 7 ng/cm 2 using a 1 μg/ml solution. Due to the multivariate complexity of ToF-SIMS data, analysis was carried out using three different methods, peak ratio calculations, principal component analysis, and artificial neural network analysis. The use of multivariate analysis with this dataset offers an unbiased analytical approach based on the peaks selected from ToF-SIMS data. The results estimate a ToF-SIMS LoD between applied antibody concentrations of 10 and 100 ng/mL. For surface bound antibodies on a silicon substrate, the LoD is below an estimated surface concentration of 49 ng/cm 2 . The authors have determined the LoD for this system using ELISA, XPS, and ToF-SIMS with multivariate analyses, with ToF-SIMS offering an order of magnitude better detection over ELISA and 2 orders of magnitude better detection over XPS.

  8. Influence of end groups in hyperbranched polyesters used as modifiers in the characteristics of epoxy thermosets cured by adipic dihydrazide

    Directory of Open Access Journals (Sweden)

    A. Serra

    2013-07-01

    Full Text Available Mixtures of diglycidylether of bisphenol A (DGEBA resin and different ratios of aliphatic-aromatic hyperbranched polyester (HBP were cured by a latent curing agent, adipic dihydrazide (AH. The HBPs prepared have hydroxyl groups or 10-undecenoyl or allyl groups as chain ends. The curing mixtures were investigated by differential scanning calorimetry (DSC to study the curing process and to evaluate the kinetic parameters of the different formulations. These studies suggest that HBPs decrease the curing rate of epoxy/AH in the case of vinyl terminated HPB, whereas OH terminated HBP accelerates the first stages and delays the lasts. The thermosets obtained showed an improvement in microhardness and impact strength without any reduction of the Tg and thermal parameters. Microparticle phase separation was observed with the undecenoyl HBP derivatives or when a 10% of allyl HBP derivative was in the formulation.

  9. Epoxy resin

    Science.gov (United States)

    Wilson, Glenn R.; Salyer, Ival O.; Ball, III, George L.

    1976-07-13

    By mixing one part of a prepolymer containing a polyamine partially polymerized with an organic epoxide and subsequently reacted with a fatty acid containing from 8 to 32 carbon atoms, and then reacting this prepolymer mixture with 3 parts of an organic epoxide, a composition was obtained which made a gas frothable, shear-stable, room temperature curing, low density foam. A particularly advantageous prepolymer was prepared using a polyamine selected from the group consisting of diethylenetriamine, triethylenetetramine, and tetraethylenepentamine, partially polymerized with an organic epoxide having an average molecular weight of about 350 and having an epoxide equivalent of 185 to 192, and reacted with 2-10 weight percent linoleic acid. When one part of this prepolymer was reacted with about three parts of epoxy, and frothed by whipping in air or nitrogen an epoxy foam was produced which could be troweled onto surfaces and into corners or crevices, and subsequently cured, at near ambient temperature, to a strong dimensionally stable foam product.

  10. Subgap in the Surface Bound States Spectrum of Superfluid ^3 He-B with Rough Surface

    Science.gov (United States)

    Nagato, Y.; Higashitani, S.; Nagai, K.

    2017-12-01

    The subgap structure in the surface bound states spectrum of superfluid ^3 He-B with rough surface is discussed. The subgap is formed by the level repulsion between the surface bound state and the continuum states in the course of multiple scattering by the surface roughness. We show that the level repulsion is originated from the nature of the wave function of the surface bound state that is now recognized as Majorana fermion. We study the superfluid ^3 He-B with a rough surface and in a magnetic field perpendicular to the surface using the quasi-classical Green function together with a random S-matrix model. We calculate the self-consistent order parameters, the spin polarization density and the surface density of states. It is shown that the subgap is found also in a magnetic field perpendicular to the surface. The magnetic field dependence of the transverse acoustic impedance is also discussed.

  11. NEXAFS characterization of DNA components and molecular-orientation of surface-bound DNA oligomers

    International Nuclear Information System (INIS)

    Samuel, Newton T.; Lee, C.-Y.; Gamble, Lara J.; Fischer, Daniel A.; Castner, David G.

    2006-01-01

    Single stranded DNA oligomers (ssDNA) immobilized onto solid surfaces forms the basis for several biotechnological applications such as DNA microarrays, affinity separations, and biosensors. Surface structure of Surface-bound oligomers is expected to significantly influence their biological activity and interactions with the environment. In this study near-edge X-ray absorption fine structure spectroscopy (NEXAFS) is used to characterize the components of DNA (nucleobases, nucleotides and nucleosides) and the orientation information of surface-bound ssDNA. The K-edges of carbon, nitrogen and oxygen have spectra with features that are characteristic of the different chemical species present in the nucleobases of DNA. The effect of addition of the DNA sugar and phosphate components on the NEXAFS K-edge spectra was also investigated. The polarization-dependent nitrogen K-edge NEXAFS data show significant changes for different orientations of surface bound ssDNA. These results establish NEXAFS as a powerful technique for chemical and structural characterization of surface-bound DNA oligomers

  12. In-situ observations of catalyst dynamics during surface-bound carbon nanotube nucleation

    DEFF Research Database (Denmark)

    Hofmann, S; Sharma, R; Du, G

    2007-01-01

    We present atomic-scale, video-rate environmental transmission electron microscopy and in situ time-resolved X-ray photoelectron spectroscopy of surface-bound catalytic chemical vapor deposition of single-walled carbon nanotubes and nanofibers. We observe that transition metal catalyst...

  13. Interference effects in laser-induced plasma emission from surface-bound metal micro-particles.

    Science.gov (United States)

    Feigenbaum, Eyal; Malik, Omer; Rubenchik, Alexander M; Matthews, Manyalibo J

    2017-05-01

    The light-matter interaction of an optical beam and metal micro-particulates at the vicinity of an optical substrate surface is critical to the many fields of applied optics. Examples of impacted fields are laser-induced damage in high power laser systems, sub-wavelength laser machining of transmissive materials, and laser-target interaction in directed energy applications. We present a full-wave-based model that predicts the laser-induced plasma pressure exerted on a substrate surface as a result of light absorption in surface-bound micron-scale metal particles. The model predictions agree with experimental observation of laser-induced shallow pits, formed by plasma emission and etching from surface-bound metal micro-particulates. It provides an explanation for the prototypical side lobes observed along the pit profile, as well as for the dependence of the pit shape on the incident laser and particle parameters. Furthermore, the model highlights the significance of the interference of the incident light in the open cavity geometry formed between the micro-particle and the substrate in the resulting pit shape.

  14. Epoxy hydantoins as matrix resins

    Science.gov (United States)

    Weiss, J.

    1983-01-01

    Tensile strength and fracture toughness of castings of the hydantoin resins cured with methylenedianiline are significantly higher than MY 720 control castings. Water absorption of an ethyl, amyl hydantoin formulation is 2.1 percent at equilibrium and Tg's are about 160 C, approximately 15 deg below the final cure temperature. Two series of urethane and ester-extended hydantoin epoxy resins were synthesized to determine the effect of crosslink density and functional groups on properties. Castings cured with methylenedianiline or with hexahydrophthalic anhydride were made from these compounds and evaluated. The glass transition temperatures, tensile strengths and moduli, and fracture toughness values were all much lower than that of the simple hydantoin epoxy resins. Using a methylene bishydantoin epoxy with a more rigid structure gave brittle, low-energy fractures, while a more flexible, ethoxy-extended hydantoin epoxy resin gave a very low Tg.

  15. Mechanical splitting of microtubules into protofilament bundles by surface-bound kinesin-1.

    Science.gov (United States)

    VanDelinder, Virginia; Adams, Peter G; Bachand, George D

    2016-12-21

    The fundamental biophysics of gliding microtubule (MT) motility by surface-tethered kinesin-1 motor proteins has been widely studied, as well as applied to capture and transport analytes in bioanalytical microdevices. In these systems, phenomena such as molecular wear and fracture into shorter MTs have been reported due the mechanical forces applied on the MT during transport. In the present work, we show that MTs can be split longitudinally into protofilament bundles (PFBs) by the work performed by surface-bound kinesin motors. We examine the properties of these PFBs using several techniques (e.g., fluorescence microscopy, SEM, AFM), and show that the PFBs continue to be mobile on the surface and display very high curvature compared to MT. Further, higher surface density of kinesin motors and shorter kinesin-surface tethers promote PFB formation, whereas modifying MT with GMPCPP or higher paclitaxel concentrations did not affect PFB formation.

  16. Effectiveness of UV-C equipped vacuum at reducing culturable surface-bound microorganisms on carpets.

    Science.gov (United States)

    Lutz, Eric A; Sharma, Smita; Casto, Bruce; Needham, Glen; Buckley, Timothy J

    2010-12-15

    Carpets are both sinks and sources for exposure to chemicals, allergens, and microbes and consequently influence health, including asthma, allergies, and infectious diseases. Asthmatics, children, and the immune-compromised are particularly vulnerable to health risks resulting from exposure to carpet contaminants. To address this risk, a commercial upright vacuum cleaner with an ultraviolet germicidal lamp (λ=253.7 nm, UVC) has been developed for residential and commercial uses. However, its effectiveness in reducing microbial load on real-world carpets has not been previously demonstrated. Accordingly, the purpose of the current study was to evaluate the effectiveness of a UVC-equipped vacuum in reducing the carpet surface-bound microbial load. This was accomplished by comparing the carpet microbial surface load from pre- to post-treatment of 9 ft(2) in-use carpet sections under three treatment scenarios: 1) UVC alone (UV), 2) the beater-bar plus vacuum (BB+Vac), or 3) a combination of all three (COMB). Each treatment was two minutes in duration. Microbial surface loads were measured by pressing contact plates containing Sabourauds Dextrose agar onto the carpet surface. In-use carpets from three locations were tested in place. The treatment effect was evaluated at two levels. First, we considered the mean reduction in CFU from pre- to post-treatment for each 9 ft(2) carpet grid (n = 4 for each treatment). The second level considered each 1 ft(2) section using a paired analysis (n = 40 to 49 for each treatment). A total of 125 pre/post-sample pairs were collected across the three treatments. Results showed that all three treatments were associated with a reduction in carpet microbial load (p < 0.0001). The COMB yielded the largest reduction of 13 CFU/plate (87% reduction) and was approximately the sum of the individual effects of either UVC (6.6 CFU/plate, 60% reduction, p = 0.009) or BB+Vac (7.3 CFU/plate, 78% reduction, p < 0.0001). We therefore conclude that a

  17. Harnessing surface-bound enzymatic reactions to organize microcapsules in solution.

    Science.gov (United States)

    Shklyaev, Oleg E; Shum, Henry; Sen, Ayusman; Balazs, Anna C

    2016-03-01

    By developing new computational models, we examine how enzymatic reactions on an underlying surface can be harnessed to direct the motion and organization of reagent-laden microcapsules in a fluid-filled microchannel. In the presence of appropriate reagents, surface-bound enzymes can act as pumps, which drive large-scale fluid flows. When the reagents diffuse through the capsules' porous shells, they can react with enzymatic sites on the bottom surface. The ensuing reaction generates fluid density variations, which result in fluid flows. These flows carry the suspended microcapsules and drive them to aggregate into "colonies" on and near the enzyme-covered sites. This aggregation continues until the reagent has been depleted and the convection stops. We show that the shape of the assembled colonies can be tailored by patterning the distribution of enzymes on the surface. This fundamental physicochemical mechanism could have played a role in the self-organization of early biological cells (protocells) and can be used to regulate the autonomous motion and targeted delivery of microcarriers in microfluidic devices.

  18. Surface-bound phosphatase activity in living hyphae of ectomycorrhizal fungi of Nothofagus obliqua.

    Science.gov (United States)

    Alvarez, Maricel; Godoy, Roberto; Heyser, Wolfgang; Härtel, Steffen

    2004-01-01

    We determined the location and the activity of surface-bound phosphomonoesterase (SBP) of five ectomycorrhizal (EM) fungi of Nothofagus oblique. EM fungal mycelium of Paxillus involutus, Austropaxillus boletinoides, Descolea antartica, Cenococcum geophilum and Pisolithus tinctorius was grown in media with varying concentrations of dissolved phosphorus. SBP activity was detected at different pH values (3-7) under each growth regimen. SBP activity was assessed using a colorimetric method based on the hydrolysis of p-nitrophenyl phosphate (pNPP) to p-nitrophenol phosphate (pNP) + P. A new technique involving confocal laser-scanning microscopy (LSM) was used to locate and quantify SBP activity on the hyphal surface. EM fungi showed two fundamentally different patterns of SBP activity in relation to varying environmental conditions (P-concentrations and pH). In the cases of D. antartica, A. boletinoides and C. geophilum, changes in SBP activity were induced primarily by changes in the number of SBP-active centers on the hyphae. In the cases of P. tinctorius and P. involutus, the number of SBP-active centers per μm hyphal length changed much less than the intensity of the SBP-active centers on the hyphae. Our findings not only contribute to the discussion about the role of SBP-active centers in EM fungi but also introduce LSM as a valuable method for studying EM fungi.

  19. Label-free quantitative proteome analysis of the surface-bound salivary pellicle.

    Science.gov (United States)

    Delius, Judith; Trautmann, Simone; Médard, Guillaume; Kuster, Bernhard; Hannig, Matthias; Hofmann, Thomas

    2017-04-01

    The salivary pellicle, covering natural as well as restored tooth surfaces in the oral cavity as an immobilized protein-rich layer, acts as an important physico-chemical and biological mediator at the tooth-saliva-interface. For the first time, the pellicle's proteome of individual volunteers were analyzed separately on three consecutive days and the relative protein abundance determined by a label-free quantitative nano-LC-MS/MS approach. A total of 72 major proteins were identified in the initial pellicles formed intraorally on dental ceramic specimens already after 3min with high inter-individual and inter-day consistency. In comparison, significant differences in protein abundance were evident between subjects, thus indicating unique individual pellicle profiles. Furthermore, the relative protein abundance in pellicles was compared to the proteome pattern in the corresponding saliva samples of the same individuals to provide first data on significantly enriched and depleted salivary proteins (p <0.05) within the surface-bound salivary pellicle. Our findings reveal the initial adsorption of salivary proteins at the solid-liquid interface to be a rapid, highly selective, and reproducible process leading to the immobilization of a broad range of protective proteins and enzymes on the substratum surface within a few minutes. This provides evidence that the pellicle layer might be physiologically functional even without further maturation. Copyright © 2017 Elsevier B.V. All rights reserved.

  20. Tracking a Common Surface-Bound Intermediate during CO2-to-Fuels Catalysis

    Science.gov (United States)

    2016-01-01

    Rational design of selective CO2-to-fuels electrocatalysts requires direct knowledge of the electrode surface structure during turnover. Metallic Cu is the most versatile CO2-to-fuels catalyst, capable of generating a wide array of value-added products, including methane, ethylene, and ethanol. All of these products are postulated to form via a common surface-bound CO intermediate. Therefore, the kinetics and thermodynamics of CO adsorption to Cu play a central role in determining fuel-formation selectivity and efficiency, highlighting the need for direct observation of CO surface binding equilibria under catalytic conditions. Here, we synthesize nanostructured Cu films adhered to IR-transparent Si prisms, and we find that these Cu surfaces enhance IR absorption of bound molecules. Using these films as electrodes, we examine Cu-catalyzed CO2 reduction in situ via IR spectroelectrochemistry. We observe that Cu surfaces bind electrogenerated CO, derived from CO2, beginning at −0.60 V vs RHE with increasing surface population at more negative potentials. Adsorbed CO is in dynamic equilibrium with dissolved 13CO and exchanges rapidly under catalytic conditions. The CO adsorption profiles are pH independent, but adsorbed CO species undergo a reversible transformation on the surface in modestly alkaline electrolytes. These studies establish the potential, concentration, and pH dependencies of the CO surface population on Cu, which serve to maintain a pool of this vital intermediate primed for further reduction to higher order fuel products. PMID:27610413

  1. Chromium Ions Improve Moisure Resistance of Epoxy Resins

    Science.gov (United States)

    St. Clair, A. K.; St. Clair, T. L.; Stoakley, D. M.; Singh, J. J.; Sprinkle, D. R.

    1986-01-01

    Broad spectrum of thermosetting epoxy resins used on commercial and military aircraft, primarily as composite matrices and adhesives. In new technique, chromium-ion containing epoxy with improved resistance to moisture produced where chromium ions believed to prevent absorption of water molecules by coordinating themselves to hydroxyl groups on epoxy chain. Anticipated that improved epoxy formulation useful as composite matrix resin, adhesive, or casting resin for applications on commercial and advanced aircraft. Improvement made without sacrifice in mechanical properties of polymer.

  2. Application of the rotating ring-disc-electrode technique to water oxidation by surface-bound molecular catalysts.

    Science.gov (United States)

    Concepcion, Javier J; Binstead, Robert A; Alibabaei, Leila; Meyer, Thomas J

    2013-10-07

    We report here the application of a simple hydrodynamic technique, linear sweep voltammetry with a modified rotating-ring-disc electrode, for the study of water oxidation catalysis. With this technique, we have been able to reliably obtain turnover frequencies, overpotentials, Faradaic conversion efficiencies, and mechanistic information from single samples of surface-bound metal complex catalysts.

  3. Four new diterpenes from the mangrove Ceriops tagal and structure revision of four dolabranes with a 4,18-epoxy group.

    Science.gov (United States)

    Zhang, Xiaohui; Li, Wanshan; Shen, Li; Wu, Jun

    2018-01-01

    Four new diterpenes named tagalons A-D (1-4), comprising an isopimarane (1), two 16-nor-pimaranes (2-3), and a dolabrane (4), were isolated from the Chinese mangrove, Ceriops tagal, together with four known dolabranes containing a 4,18-epoxy group, viz. tagalene I (5), 4-epitagalene I (6), tagalsin A (7), and tagalsin B (8). The structures of these compounds were unambiguously established by HR-ESIMS and NMR spectroscopic data. Based on the new criteria of NOE interactions between H 2 -18/H 3 -19 and H 2 -18/H 3 -20, previously reported relative configurations of the above four known dolabranes were correctly revised as their C-4 epimers, respectively. The relative configuration of tagalon B (2) and the absolute configuration of tagalene I (5) were established by single-crystal X-ray diffraction analyses, conducted with Cu Kα radiation. Most notably, tagalons C (3) and D (4) exhibited selective cytotoxicities against the human breast cancer cell line MT-1 with IC 50 values of 3.75 and 8.07μM, respectively; whereas tagalene I (5) displayed potent cytotoxic effects against four human breast cancer cell lines MDA-MB-453, MDA-MB-231, SK-BR-3, and MT-1 with IC 50 values of 8.97, 8.97, 4.62, and 3.93μM, respectively. Copyright © 2017 Elsevier B.V. All rights reserved.

  4. Statistical investigation of surface bound ions and further development of BION server to include pH and salt dependence.

    Science.gov (United States)

    Petukh, Marharyta; Zhang, Min; Alexov, Emil

    2015-12-15

    Ions are engaged in multiple biological processes in cells. By binding to the macromolecules or being mobile in the solvent, they maintain the integrity of the structure of macromolecules; participate in their enzymatic activity; or screen electrostatic interactions. While experimental methods are not always able to assign the exact location of ions, computational methods are in demand. Although the majority of computational methods are successful in predicting the position of ions buried inside macromolecules, they are less effective in deciphering positions of surface bound ions. Here, we propose the new BION algorithm (http://compbio.clemson.edu/bion_server_ph/) that predicts the location of the surface bound ions. It is more efficient and accurate compared to the previous version since it uses more advanced clustering algorithm in combination with pairing rules. In addition, the BION webserver allows specifying the pH and the salt concentration in predicting ions positions. © 2015 Wiley Periodicals, Inc.

  5. Epoxy Nanocomposites Containing Zeolitic Imidazolate Framework-8.

    Science.gov (United States)

    Liu, Cong; Mullins, Michael; Hawkins, Spencer; Kotaki, Masaya; Sue, Hung-Jue

    2018-01-10

    Zeolitic imidazole framework-8 (ZIF-8) is utilized as a functional filler and a curing agent in the preparation of epoxy nanocomposites. The imidazole group on the surface of the ZIF-8 initiates epoxy curing, resulting in covalent bonding between the ZIF-8 crystals and epoxy matrix. A substantial reduction in dielectric constant and increase in tensile modulus were observed. The implication of the present study for utilization of metal-organic framework to improve physical and mechanical properties of polymeric matrixes is discussed.

  6. Flame Retardant Epoxy Resins

    Science.gov (United States)

    Thompson, C. M.; Smith, J. G., Jr.; Connell, J. W.; Hergenrother, P. M.; Lyon, R. E.

    2004-01-01

    As part of a program to develop fire resistant exterior composite structures for future subsonic commercial aircraft, flame retardant epoxy resins are under investigation. Epoxies and their curing agents (aromatic diamines) containing phosphorus were synthesized and used to prepare epoxy formulations. Phosphorus was incorporated within the backbone of the epoxy resin and not used as an additive. The resulting cured epoxies were characterized by thermogravimetric analysis, propane torch test, elemental analysis and microscale combustion calorimetry. Several formulations showed excellent flame retardation with phosphorous contents as low as 1.5% by weight. The fracture toughness of plaques of several cured formulations was determined on single-edge notched bend specimens. The chemistry and properties of these new epoxy formulations are discussed.

  7. Modification of (DGEBA epoxy resin with maleated depolymerised natural rubber

    Directory of Open Access Journals (Sweden)

    2008-04-01

    Full Text Available In this work, diglycidyl ether of bisphenol A (DEGBA type epoxy resin has been modified with maleated depolymerised natural rubber (MDPR. MDPR was prepared by grafting maleic anhydride onto depolymerised natural rubber. MDPR has been characterized by Fourier transform infrared (FT-IR spectroscopy and nuclear magnetic resonance spectroscopy. MDPR was blended with epoxy resin at three different ratios (97/3, 98/2 and 99/1, by keeping the epoxy resin component as the major phase and maleated depolymerised natural rubber component as the minor phase. The reaction between the two blend components took place between the acid/anhydride group in the MDPR and the epoxide group of the epoxy resin. The proposed reaction schemes were supported by the FT-IR spectrum of the uncured Epoxy/MDPR blends. The neat epoxy resin and Epoxy/MDPR blends were cured by methylene dianiline (DDM at 100°C for three hours. Thermal, morphological and mechanical properties of the neat epoxy and the blends were investigated. Free volume studies of the cured, neat epoxy and Epoxy/MDPR blends were correlated with the morphological and mechanical properties of the same systems using Positron Annihilation Lifetime Studies.

  8. Factors influencing EB curing of epoxy matrix

    International Nuclear Information System (INIS)

    Li Fengmei; Bao Jianwen; Chen Xiangbao; Bao Huaying; Wang Huiliang

    2002-01-01

    The effectiveness of electron beam (EB) curing of epoxy resins was found to be influenced by catalyst. In the presence of iodonium salt (diaryl iodonium hexafluoroantimonate, C3), the EB curing of epoxy resin is easier than in the presence of triaryl sulfonium hexafluoroantimonate (C1), or triaryl sulfonium hexafluorophosphate (C2), or iron arene containing cationic catalyst (Irgacure 261). The epoxy 616 (diglycidyl ether of bisphenol A) and 648 (diglycidyl ether of phenolic novolacs) can be cured by the above onium salts catalysts C1-C3. The epoxy with glycidyl amino epoxide group (such as AG 80; AFG 90) could not be cured by onium salts catalyst. The influence of irradiation dose, temperature and the effect of impurities on curing reaction were investigated

  9. Adding Effects of Reactive Oligomers for Epoxy Resin

    OpenAIRE

    山田, 英介; 稲垣, 慎二; 岡本, 弘

    1991-01-01

    Reactive oligomers with both functional end groups were prepared by the radical telomerization and the effect of oligomers added to bisphenol-A-glycidylehter type epoxy resin was investigated by measuring mechanical properties, adhesive properties and dynamic viscoelasticities. These oligomers were high viscous liquid except the one prepared from methyl methacrylate, therefore the blend of oligomers with epoxy resin is easy. Adding oligomers, the cured epoxy resins showed the lower glass-tran...

  10. Mechanical Reinforcement of Epoxy Composites with Carbon Fibers and HDPE

    Science.gov (United States)

    He, R.; Chang, Q.; Huang, X.; Li, J.

    2018-01-01

    Silanized carbon fibers (CFs) and a high-density polyethylene with amino terminal groups (HDPE) were introduced into epoxy resins to fabricate high-performance composites. A. mechanical characterization of the composites was performed to investigate the effect of CFs in cured epoxy/HDPE systems. The composites revealed a noticeable improvement in the tensile strength, elongation at break, flexural strength, and impact strength in comparison with those of neat epoxy and cured epoxy/HDPE systems. SEM micrographs showed that the toughening effect could be explained by yield deformations, phase separation, and microcracking.

  11. Nanostructured epoxi networks

    International Nuclear Information System (INIS)

    Soares, Bluma G.; Silva, Adriana A.; Sollymossy, Ana Paula F.; Dahmouche, Karim

    2011-01-01

    Nanostructured epoxy materials including nanocomposites were obtained by incorporating different organic or inorganic systems. Epoxy networks containing rubber particles with nanometric size have been obtained by an appropriate functionalization of the elastomers, in order to improve the interfacial adhesion between rubber and epoxy matrix. This adhesion also conferred an improvement of the impact resistance and thermal properties. This work also presents some results related to the utilization of inorganic nanoparticles in epoxy systems, including organo clay or hybrid materials based on functionalized silsesquioxanes. The nanoscopic characterization of these materials were performed by small angle X-ray scattering (SAXS) combined with transmission electron microscopy (TEM). The effect of dispersion degree of the inorganic nanoparticles on the rheological properties was also investigated. (author)

  12. Contact allergy to epoxy resin

    DEFF Research Database (Denmark)

    Bangsgaard, Nannie; Thyssen, Jacob Pontoppidan; Menné, Torkil

    2012-01-01

    to epoxy resin remained stable over the study period. Of the patients with an epoxy resin-positive patch test, 71% returned a questionnaire; 95 patients had worked with epoxy resin in the occupational setting, and, of these, one-third did not use protective gloves and only 50.5% (48) had participated...

  13. COOH functionalized MWNTs/epoxy composites

    Indian Academy of Sciences (India)

    2017-08-05

    Aug 5, 2017 ... Functionalized multi-wall carbon nanotubes (MWNTs) with carboxylic acid group (–COOH) have been utilized for the preparation of .... epoxy polymer by forming covalent bonds between the nan- otubes and the matrix. ..... to the hybrid structure of CNTs and basalt fibres that form a co-supporting network.

  14. Preparation of sulfonated poly(ether ether ketone)s containing amino groups/epoxy resin composite membranes and their in situ crosslinking for application in fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Guo, Meimei; Liu, Baijun; Li, Long; Liu, Chang; Wang, Lifeng; Jiang, Zhenhua [Alan G. MacDiarmid Institute, Jilin University, 2699 Qianjin Street, Changchun 130012 (China)

    2010-01-01

    A series of amino-containing sulfonated poly(aryl ether ketone)/4,4'-diglycidyl(biphenyl) epoxy resin (DGBP) composite membranes for proton exchange membranes fuel cells (PEMFCs) are prepared by solution blending and casting. The reaction kinetics and the effects of introduction of DGBP content on the properties of the composite membranes are thoroughly investigated. The crosslinked composite membranes after treatment at either 120 C or 200 C have improved oxidative and dimensional stability than those without crosslinking. Despite the fact that crosslinked membranes generally have lower proton conductivity in comparison with the original ones, the proton conductivities of the membranes treated at 120 C are above 2.22 x 10{sup -2} S cm{sup -1} at room temperature and 9.42 x 10{sup -2} S cm{sup -1} at 100 C. Even for the samples treated at 200 C, their proton conductivities are still higher than 1.26 x 10{sup -2} S cm{sup -1} at room temperature and higher than 8.67 x 10{sup -2} S cm{sup -1} at 100 C, which are well satisfied with elementary requirement of fuel cells. In addition, all the evaluated membranes have low methanol permeability. For example, the methanol permeability of AP6FSPEEK/DGBP1 cured at 200 C is 0.33 x 10{sup -6} cm{sup 2} s{sup -1}, which is an order magnitude lower than Nafion 117. Therefore, these novel crosslinked composite membranes could be potential usage in fuel cells. (author)

  15. sisal fibre- epoxy compos

    African Journals Online (AJOL)

    eobe

    2015-10-04

    Oct 4, 2015 ... 2, 4 PHYSICS ADVANCED LABORATORY, SHEDA SCIENCE AND TECHNOLOGY COMPLEX, SHEDA, ABUJA FCT NIGERIA. 3NUCLEAR .... [33]. However, polyesters, vinyl ester and other thermosetting resins can also be used for fiber reinforced composite materials. The choice of epoxy matrix in this ...

  16. Electron Transfer Mediator Effects in Water Oxidation Catalysis by Solution and Surface-Bound Ruthenium Bpy-Dicarboxylate Complexes

    Energy Technology Data Exchange (ETDEWEB)

    Sheridan, Matthew V.; Sherman, Benjamin D.; Marquard, Seth L.; Fang, Zhen; Ashford, Dennis L.; Wee, Kyung-Ryang; Gold, Alexander S.; Alibabaei, Leila; Rudd, Jennifer A.; Coggins, Michael K.; Meyer, Thomas J.

    2015-11-12

    Electrocatalytic water oxidation by the catalyst, ruthenium 2,2'-bipyridine-6,6'-dicarboxylate (bda) bis-isoquinoline (isoq), [Ru(bda)(isoq)2], 1, was investigated at metal oxide electrodes surface-derivatized with electron transfer (ET) mediators. At indium-doped tin oxide (ITO) in pH 7.2 in H2PO4–/HPO42– buffers in 0.5 M NaClO4 with added acetonitrile (MeCN), the catalytic activity of 1 is enhanced by the surface-bound redox mediators [Ru (4,4'-PO3H2-bpy)(4,4'-R-bpy)2]2+ (RuPbpyR22+, R = Br, H, Me, or OMe, bpy = 2,2'-bipyridine). Rate-limiting ET between the Ru3+ form of the mediator and the RuIV(O) form in the [RuV/IV(O)]+/0 couple of 1 is observed at relatively high concentrations of HPO42– buffer base under conditions where O···O bond formation is facilitated by atom-proton transfer (APT). For the solution [Ru(bpy)3]3+/2+ mediator couple and 1 as the catalyst, catalytic currents vary systematically with the concentration of mediator and the HPO42– buffer base concentration. Electron transfer mediation of water oxidation catalysis was also investigated on nanoparticle TiO2 electrodes co-loaded with catalyst [Ru(bda)(py-4-O(CH2)3-PO3H2)2], 2, (py = pyridine) and RuPbpyR22+ (R = H, Me, or OMe) with an interplay between rate-limiting catalyst oxidation and rate-limiting O···O bond formation by APT. Lastly, the co-loaded assembly RuPbpyR22+ + 2 has been investigated in a dye-sensitized photoelectrosynthesis cell for water splitting.

  17. The Generation of Surface-bound Exospheres via Electron-Stimulated Desorption (and Related Phenomena): Results from Apollo samples and Hermian Regolith Simulants

    Science.gov (United States)

    Bennett, C.; Poston, M.; McLain, J. L.; Orlando, T. M.

    2014-12-01

    The generation of surface-bound exospheres present around the Moon, Mercury and other airless rocky bodies are produced primarily by the interaction of micrometeoroid impacts and charged particles from the solar wind, and magnetospheres with those surfaces. While the study of the interactions of both micrometeoroids and ion sputtering are well investigated, the contributions arising from energetic electron interactions are typically less-well established. Observations from the Fast Imaging Plasma Spectrometer (FIPS), taken < 400 km from the surface, have shown a plasma cusp with energetic heavy ions (i.e. Na+- and O+-groups) for which the source has not been determined. However, the precipitation of keV electrons onto the surfaces of Mercury has recently been inferred from measurements using the X-Ray Spectrometer (XRS) instrument onboard the MESSENGER spacecraft observations of the night-side of Mercury. A newly developed global kinetic transport model suggests that electron-stimulated desorption (ESD), and possibly light ion stimulated desorption (ISD), can directly yield ions that can be transported and dynamically accelerated to the plasma cusp regions observed by FIPS. In addition, keV electrons and ions from the solar wind and Earth's magnetosphere frequently bombard with the lunar surface. Here, we present some of the most recent results from our ongoing work studying the effects of photon-stimulated desorption (PSD), ion-stimulated desorption (ISD) and implantation, as well as electron-stimulated desorption (ESD). Apollo samples collected from both the lunar highland and Mare regions, as well as simulants of the Mercury Regolith have been investigated. The temperature- (100-600 K) and energy-dependence (threshold - 2 keV) of ESD time-of-flight (ToF) results will be presented for these materials along with some preliminary results from our group based on photon-desorption studies of water on lunar material, temperature-programmed desorption (TPD) studies of

  18. Epoxy-resin adhesive and method for bonding using such an epoxy resin adhesive

    NARCIS (Netherlands)

    Bhowmik, S.; Poulis, J.A.; Benedictus, R.

    2008-01-01

    The invention relates to an epoxy resin adhesive comprising a dotation of nano-substances, wherein the nano- substances are selected from the group comprising carbon-fibre nanotubes, carbon nano-fibres, silicate nano powders, and wherein the nano-substances are dispersed in the adhesive with a

  19. Occupational exposure to epoxy resins

    NARCIS (Netherlands)

    Terwoert, J.; Kersting, K.

    2014-01-01

    Products based on epoxy resins as a binder have become popular in various settings, among which the construction industry and in windmill blade production, as a result of their excellent technical properties. However, due to the same properties epoxy products are a notorious cause of allergic skin

  20. Novel phosphorus containing epoxy networks

    OpenAIRE

    1989-01-01

    Epoxy resins can be cured or crosslinked with triphenyl phosphine oxide compounds having epoxy-reactive (active hydrogen) substituents either alone or in combination with amine-terminated polyarylene ethers (e.g., amine-terminated polysulfone oligomers or high polymers.

  1. Electrically Conductive Epoxy Adhesives

    Directory of Open Access Journals (Sweden)

    Lan Bai

    2011-02-01

    Full Text Available Conductive adhesives are widely used in electronic packaging applications such as die attachment and solderless interconnections, component repair, display interconnections, and heat dissipation. The effects of film thickness as functions of filler volume fraction, conductive filler size, shape, as well as uncured adhesive matrix viscosity on the electrical conduction behavior of epoxy-based adhesives are presented in this work. For this purpose, epoxy-based adhesives were prepared using conductive fillers of different size, shape, and types, including Ni powder, flakes, and filaments, Ag powder, and Cu powder. The filaments were 20 μm in diameter, and 160 or 260 μm in length. HCl and H3PO4 acid solutions were used to etch and remove the surface oxide layers from the fillers. The plane resistance of filled adhesive films was measured using the four-point method. In all cases of conductive filler addition, the planar resistivity levels for the composite adhesive films increased when the film thickness was reduced. The shape of resistivity-thickness curves was negative exponential decaying type and was modeled using a mathematical relation. The relationships between the conductive film resistivities and the filler volume fractions were also derived mathematically based on the experimental data. Thus, the effects of surface treatment of filler particles, the type, size, shape of fillers, and the uncured epoxy viscosity could be included empirically by using these mathematical relations based on the experimental data. By utilizing the relations we proposed to model thickness-dependent and volume fraction-dependent conduction behaviors separately, we were able to describe the combined and coupled volume fraction-film thickness relationship mathematically based on our experimental data.

  2. Interaction of water with epoxy.

    Energy Technology Data Exchange (ETDEWEB)

    Powers, Dana Auburn

    2009-07-01

    The chemistries of reactants, plasticizers, solvents and additives in an epoxy paint are discussed. Polyamide additives may play an important role in the absorption of molecular iodine by epoxy paints. It is recommended that the unsaturation of the polyamide additive in the epoxy cure be determined. Experimental studies of water absorption by epoxy resins are discussed. These studies show that absorption can disrupt hydrogen bonds among segments of the polymers and cause swelling of the polymer. The water absorption increases the diffusion coefficient of water within the polymer. Permanent damage to the polymer can result if water causes hydrolysis of ether linkages. Water desorption studies are recommended to ascertain how water absorption affects epoxy paint.

  3. Cure reaction of epoxy resins catalyzed by graphite-based nanofiller

    Science.gov (United States)

    Corcione, C. Esposito; Acocella, Maria Rosaria; Giuri, Antonella; Maffezzoli, Alfonso; Guerra, Gaetano

    2015-12-01

    A significant effort was directed to the synthesis of graphene stacks/epoxy nanocomposites and to the analysis of the effect of a graphene precursor on cure reaction of a model epoxy matrix. A comparative thermal analysis of epoxy resins filled with an exfoliated graphite oxide eGO were conducted. The main aim was to understand the molecular origin of the influence of eGO on the Tg of epoxy resins. The higher Tg values previously observed for low curing temperatures, for epoxy resins with graphite-based nanofillers, were easily rationalized by a catalytic activity of graphitic layers on the reaction between the epoxy and amine groups of the resin, which leads to higher crosslinking density in milder conditions. A kinetic analysis of the cure mechanism of the epoxy resin associated to the catalytical activity of the graphite based filler was performed by isothermal DSC measurements. The DSC results showed that the addition of graphite based filler greatly increased the enthalpy of epoxy reaction and the reaction rate, confirming the presence of a catalytic activity of graphitic layers on the crosslinking reaction between the epoxy resin components (epoxide oligomer and di-amine). A kinetic modelling analysis, arising from an auto-catalyzed reaction mechanism, was finally applied to isothermal DSC data, in order to predict the cure mechanism of the epoxy resin in presence of the graphite based nanofiller.

  4. Remediation of Uranium-Contaminated Concrete Coated Epoxy

    International Nuclear Information System (INIS)

    Kim, S. S.; Kim, W. S.; Kim, G. N.; Moon, J. K.

    2013-01-01

    A volume reduction of the concrete waste by appropriate treatment technologies will decrease the amount of waste to be disposed of and result in a reduction of the disposal cost and an enhancement of the efficiency of the disposal site. As decontamination techniques for concrete, biological methods, chemical methods, strippable coating, laser ablation, microwave heating and electrokinetic have been developed. In this study, decontamination methods for U-contaminated concrete pieces with and without epoxy were examined and the amount of waste sludge generated from the treatment was evaluated. In addition, nitric acid and sulfuric acid were used as the washing solution for the uranium, and their efficiencies were also compared to one another. The concrete pieces produced from the decommissioning of a uranium conversion plant were divided into two groups, concrete coated with epoxy and concrete without epoxy. The concrete pieces without epoxy were easily decontaminated by washing with 0.1M sulfuric or nitric acid and then separation of the cement paste. In concrete coated with epoxy, a high concentration of uranium exists in a mortar layer under epoxy. When these concrete pieces were heated for 2 hours at 400 .deg. C, pulverized and sequentially washed with 0.1, 2.0 and 1.0 M of nitric acid, their radioactivity reached below the limit value of uranium for self-disposal

  5. Radiation resistance of epoxy resins and their composistes

    International Nuclear Information System (INIS)

    Sonoda, Katsumi; Hayashi, Osamu; Tanaka, Takao; Hirabayashi, Shoji; Amakawa, Tadashi.

    1984-01-01

    In the electric equipment installed inside containment vessels in nuclear power plants, many epoxy resins have been employed as insulating materials. However, there are very few reports on the investigation of their properties in such environment, specifically under LOCA (Loss-of-Coolant Accident) conditions. This paper investigates on the electrical and mechanical properties of the epoxy resins supposed to be applicable to the actual equipment, by LOCA simulation. The epoxy resins used for the experiment were the following three types: (1) typical epoxy resin, bisphenol A group; (2) novolak group epoxy resins in consideration of improving humidity resistance; and (3) triazine group epoxy resins for the purpose of giving radiation, humidity and heat resistances. The last one includes the composites with Nomex and with laminated mica. After LOCA simulation which is composed of up to 2 MGy irradiation of 60 Co γ-ray at the dose rate of 10 4 Gy/h and the exposure to high temperature saturated steam, the electrical properties of dielectric tangent, insulation breakdown voltage (BDV) and conductivity and the mechanical properties of bending strength and viscoelasticity were measured. In the paper, the experimental results are described in detail. Of these, the triazine group epoxy/Nomex composite did not show swelling, but demonstrated stable radiation resistance. It is excellent in the electrical and mechanical properties, and also shows good dimension-stability. In LOCA simulation, its bending strength was reduced than that for only γ-irradiation of 2 MGy, but still had the residual strength of about 80 %. (Wakatsuki, Y.)

  6. Flame resistant hybrid epoxy composites

    Czech Academy of Sciences Publication Activity Database

    Śliwa, R.; Oleksy, M.; Heneczkowski, M.; Oliwa, R.; Budzik, G.; Kozik, B.; Markowska, O.; Strachota, Adam

    2015-01-01

    Roč. 60, č. 10 (2015), s. 667-670 ISSN 0032-2725 Institutional support: RVO:61389013 Keywords : epoxy resin * quaternary phosphonium salts * modified bentonite Subject RIV: CD - Macromolecular Chemistry Impact factor: 0.718, year: 2015

  7. Cross-reactivity among epoxy acrylates and bisphenol F epoxy resins in patients with bisphenol A epoxy resin sensitivity.

    Science.gov (United States)

    Lee, Han N; Pokorny, Christopher D; Law, Sandra; Pratt, Melanie; Sasseville, Denis; Storrs, Frances J

    2002-09-01

    The study's objective was 2-fold: first, to evaluate the potential cross-reactivity between Bis-A epoxy resins and epoxy acrylates and second, to study the cross reactivity between Bis-A epoxy resins and newer Bis-F epoxy resins in patients with allergic contact dermatitis to epoxy resins and had positive patch test to the standard epoxy resin based on bisphenol A. Forty-one patients were patch tested to 23 chemicals including epoxy acrylates, Bis-A epoxy resins, and Bis-F epoxy resins, as well as reactive diluents and nonbisphenol epoxy resins. Questions concerning exposure to epoxy resins, occupational history, and problems with dental work were completed. All patients included in the study had positive reactions to the standard Bis-A epoxy resin. Twenty percent (8 of 41) of the patients reacted to at least one of the epoxy acrylates; the most common reaction was to Bis-GMA. Five of 8 patients who reacted to the epoxy acrylates had dental work, but only one patient had problems from her dental work. Six of 8 patients (75%) who reacted to epoxy resins and epoxy acrylates did not react to aliphatic acrylates. Thirty-two percent (13 of 41) reacted to tosylamide epoxy resin, and none reacted to triglycidyl isocyanurate resin. In addition, all patients (100%) had positive reactions to at least one of the Bis-F epoxy resins that were tested. Most patients with sensitivity to Bis-A epoxy resins do not cross-react with epoxy acrylates. Patients with positive patch test reactions to epoxy acrylates used in dentistry usually do not have symptoms from their dental work. To our knowledge, this is the largest series of patients with sensitivity to the standard Bis-A epoxy resin that have been patch tested with the more recently introduced Bis-F epoxy resins. There is significant cross-reactivity between Bis-A and Bis-F epoxy resins, which can be explained by their structural similarity. Copyright 2002, Elsevier Science (USA). All rights reserved.

  8. Surface modification of titanium hydride with epoxy resin via microwave-assisted ball milling

    Energy Technology Data Exchange (ETDEWEB)

    Ning, Rong [College of Materials Science and Engineering, Hunan University, Changsha 410082 (China); Chen, Ding, E-mail: ma97chen@hotmail.com [College of Materials Science and Engineering, Hunan University, Changsha 410082 (China); Zhang, Qianxia [College of Materials Science and Engineering, Hunan University, Changsha 410082 (China); Bian, Zhibing; Dai, Haixiong; Zhang, Chi [Jiangsu Jinling Special Paint Co., Ltd., Yangzhou 225212 (China)

    2014-10-15

    Highlights: • TiH{sub 2} was modified with epoxy resin by microwave-assisted ball milling. • The epoxy ring was opened under the coupling effect of microwave and ball milling. • Microwave-assisted ball milling improved the compatibility of TiH{sub 2} with epoxy. - Abstract: Surface modification of titanium hydride with epoxy resin was carried out via microwave-assisted ball milling and the products were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), thermo-gravimetry (TG) and Fourier transform infrared spectroscopy (FT-IR). A sedimentation test was performed to investigate the compatibility of the modified nano titanium hydride with the epoxy resin. The results show that the epoxy resin molecules were grafted on the surface of nano titanium hydride particles during the microwave-assisted ball milling process, which led to the improvement of compatibility between the nanoparticles and epoxy resin. According to the FT-IR, the grafting site was likely to be located around the epoxy group due to the fact that the epoxy ring was opened. However, compared with microwave-assisted ball milling, the conventional ball milling could not realize the surface modification, indicating that the coupling effect of mechanical force and microwave played a key role during the process.

  9. Surface modification of titanium hydride with epoxy resin via microwave-assisted ball milling

    International Nuclear Information System (INIS)

    Ning, Rong; Chen, Ding; Zhang, Qianxia; Bian, Zhibing; Dai, Haixiong; Zhang, Chi

    2014-01-01

    Highlights: • TiH 2 was modified with epoxy resin by microwave-assisted ball milling. • The epoxy ring was opened under the coupling effect of microwave and ball milling. • Microwave-assisted ball milling improved the compatibility of TiH 2 with epoxy. - Abstract: Surface modification of titanium hydride with epoxy resin was carried out via microwave-assisted ball milling and the products were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), thermo-gravimetry (TG) and Fourier transform infrared spectroscopy (FT-IR). A sedimentation test was performed to investigate the compatibility of the modified nano titanium hydride with the epoxy resin. The results show that the epoxy resin molecules were grafted on the surface of nano titanium hydride particles during the microwave-assisted ball milling process, which led to the improvement of compatibility between the nanoparticles and epoxy resin. According to the FT-IR, the grafting site was likely to be located around the epoxy group due to the fact that the epoxy ring was opened. However, compared with microwave-assisted ball milling, the conventional ball milling could not realize the surface modification, indicating that the coupling effect of mechanical force and microwave played a key role during the process

  10. Green Preparation of Epoxy/Graphene Oxide Nanocomposites Using a Glycidylamine Epoxy Resin as the Surface Modifier and Phase Transfer Agent of Graphene Oxide.

    Science.gov (United States)

    Tang, Xinlei; Zhou, Yang; Peng, Mao

    2016-01-27

    In studies of epoxy/graphene oxide (GO) nanocomposites, organic solvents are commonly used to disperse GO, and vigorous mechanical processes and complicated modification of GO are usually required, increasing the cost and hindering the development and application of epoxy nanocomposites. Here, we report a green, facile, and efficient method of preparing epoxy/GO nanocomposites. When triglycidyl para-aminophenol (TGPAP), a commercially available glycidyl amine epoxy resin with one tertiary amine group per molecule, is used as both the surface modifier and phase transfer agent of GO, GO can be directly and rapidly transferred from water to diglycidyl ether of bisphenol A and other types of epoxy resins by manual stirring under ambient conditions, whereas GO cannot be transferred to these epoxy resins in the absence of TGPAP. The interaction between TGPAP and GO and the effect of the TGPAP content on the dispersion of GO in the epoxy matrix were investigated systematically. Superior dispersion and exfoliation of GO nanosheets and remarkably improved mechanical properties, including tensile and flexural properties, toughness, storage modulus, and microhardness, of the epoxy/GO nanocomposites with a suitable amount of TGPAP were demonstrated. This method is organic-solvent-free and technically feasible for large-scale preparation of high-performance nanocomposites; it opens up new opportunities for exploiting the unique properties of graphene or even other nanofillers for a wide range of applications.

  11. The effects of intracrystalline and surface-bound proteins on the attachment of calcium oxalate monohydrate crystals to renal cells in undiluted human urine.

    Science.gov (United States)

    Grover, Phulwinder K; Thurgood, Lauren A; Wang, Tingting; Ryall, Rosemary L

    2010-03-01

    To compare the binding to Madin-Darby canine kidney (MDCK)-II cells of: (i) inorganic calcium oxalate monohydrate (iCOM) crystals and COM crystals precipitated from urine containing different concentrations of protein; and (ii) urinary COM crystals containing intracrystalline and intracrystalline + surface-bound protein. Urinary COM crystals were generated in sieved (sCOM), centrifuged and filtered (cfCOM), and ultrafiltered (ufCOM) portions of a pooled human urine and their adhesion to MDCK-II cells was compared using six different ultrafiltered urine samples as the binding medium. Crystal matrix extract (CME) was prepared by demineralizing calcium oxalate crystals precipitated from human urine and used to prepare COM crystals with intracrystalline, and intracrystalline + surface-bound CME at protein concentrations of 0, 0.05, 0.1, 0.5 and 5.0 mg/L. The amount of protein associated with the crystals was qualitatively assessed by sodium dodecyl sulphate-polyacrylamide gel electrophoresis and Western blotting, using prothrombin fragment 1 (PTF1) as a marker. Protein concentration was determined in sieved, centrifuged and filtered, and ultrafiltered fractions of 10 additional urine samples. The median crystal attachment in the six urine types decreased in the order iCOM > ufCOM > cfCOM = sCOM, in inverse proportion to the concentration of protein in the solution or urine from which they were precipitated. sCOM and cfCOM crystals bound approximately 23% less than iCOM crystals. The attachment of COM crystals generated in the presence of increasing concentrations of CME proteins was unaffected up to a concentration of 5 mg/L, but binding of crystals containing the same concentrations of intracrystalline + surface-bound proteins decreased proportionally at protein concentrations from 0 to 5.0 mg/L. Inorganic COM crystals bind significantly more strongly to MDCK-II cells than urinary crystals precipitated from sieved, centrifuged and filtered, and ultrafiltered urine

  12. Paramagnetic epoxy resin

    Directory of Open Access Journals (Sweden)

    E. C. Vazquez Barreiro

    2017-01-01

    Full Text Available This work illustrates that macrocycles can be used as crosslinking agents for curing epoxy resins, provided that they have appropriate organic functionalities. As macrocycles can complex metal ions in their structure, this curing reaction allows for the introduction of that metal ion into the resin network. As a result, some characteristic physical properties of the metallomacrocycle could be transferred to the new material. The bisphenol A diglycidyl ether (BADGE, n = 0 and hemin (a protoporphyrin IX containing the Fe(III ion, and an additional chloride ligand have been chosen. The new material has been characterized by differential scanning calorimetry (DSC, thermogravimetric analysis (TGA, Fourier Transform Infrared (FT-IR, Nuclear Magnetic Resonance (NMR, Transmission Electron Microscopy (TEM, and magnetic susceptibility measurements. Fe(III remains in the high-spin state during the curing process and, consequently, the final material exhibits the magnetic characteristics of hemin. The loss of the chlorine atom ligand during the cure of the resin allows that Fe(III can act as Lewis acid, catalyzing the crosslinking reactions. At high BADGE n = 0/hemin ratios, the formation of ether and ester bonds occurs simultaneously during the process.

  13. New Organic Solvent Free Three-Component Waterproof Epoxy-Polyamine Systems

    Directory of Open Access Journals (Sweden)

    C. M. LACNJEVAC

    2010-08-01

    Full Text Available The unmodified GY epoxy resin (Vantico AG was crosslinked by the aliphatic and cycloaliphatic EH polyamine adduct (Solutia-Vianova in the different stoichiometric ratio. The optimal time of total crosslinking was determined by indirect measuring of the film hardness. The degree of the epoxy resin crosslinking and the quantity of unreacted epoxy groups have been monitored by the spectroscopic FT-IR method. The content and intensity changes of hydroxy group were correlated to the extent of epoxy reaction and crosslinking degree. By the parameters correlation and a period of resins application, optimal resin/hardeners stoichiometric ratio was defined. It was prerequisite for three-component epoxy system forming which is comparatively more elastic, adhesion and waterproof.

  14. Analysis by Fourier Transform Infrared (FTIR) of the gamma radiation effect on epoxy resin, used as solidification agent of radioactive wastes

    International Nuclear Information System (INIS)

    Liu, C.H.; Riella, H.G.; Guedes, S.M.L.

    1995-01-01

    The effects of gamma radiation on Epoxy resin, used as solidification agent of radioactive wastes, were studied by Fourier Transform Infrared (FTIR). The spectra showed no significant modifications on Epoxy resin functional groups (irradiated with dose from 0 to 1 MGy). Up to 1 MGy Epoxy resin did not oxidize, confirming the Epoxy good radiation strength. The presence of aromatic chain and amine group, mainly tertiary amine, give good radiolytic stability to the Epoxy, increasing the interest to use this material in nuclear facilities. (author). 3 refs, 2 figs

  15. Homogeneous Liquid Phase Transfer of Graphene Oxide into Epoxy Resins.

    Science.gov (United States)

    Amirova, Lyaysan; Surnova, Albina; Balkaev, Dinar; Musin, Delus; Amirov, Rustem; Dimiev, Ayrat M

    2017-04-05

    The quality of polymer composite materials depends on the distribution of the filler in the polymer matrix. Due to the presence of the oxygen functional groups, graphene oxide (GO) has a strong affinity to epoxy resins, providing potential opportunity for the uniform distribution of GO sheets in the matrix. Another advantage of GO over its nonoxidized counterpart is its ability to exfoliate to single-atomic-layer sheets in water and in some organic solvents. However, these advantages of GO have not yet been fully realized due to the lack of the methods efficiently introducing GO into the epoxy resin. Here we develop a novel homogeneous liquid phase transfer method that affords uniform distribution, and fully exfoliated condition of GO in the polymer matrix. The most pronounced alteration of properties of the cured composites is registered at the 0.10%-0.15% GO content. Addition of as little as 0.10% GO leads to the increase of the Young's modulus by 48%. Moreover, we demonstrate successful introduction of GO into the epoxy matrix containing an active diluent-modifier; this opens new venues for fabrication of improved GO-epoxy-modifier composites with a broad range of predesigned properties. The experiments done on reproducing the two literature methods, using alternative GO introduction techniques, lead to either decrease or insignificant increase of the Young's modulus of the resulting GO-epoxy composites.

  16. Plasma exposure tests of a carbon fiber/epoxy composite

    International Nuclear Information System (INIS)

    Schneider, T.; Rome, J.

    1988-07-01

    An experiment was conducted to test the exposure of a vacuum chamber made of a carbon fiber/epoxy composite to a plasma environment. In previous tests this material(CE 339, made by Ferro Corp.) has shown good vacuum properties and has also demonstrated the capability to withstand high energy electron beams in tests at the Naval Research Laboratory. Based on these promising results, the Torsatron Group at Auburn University conducted plasma exposure tests on a section of carbon fiber/epoxy composite pipe furnished by Oak Ridge National Laboratory. 1 ref, 2 figs

  17. Fabrication of an epoxy-insulated Marshall Coil

    International Nuclear Information System (INIS)

    Eaton, E.E.; Ehart, E.P.; Ebaugh, L.R.; Fox, A.G.; Dickinson, J.M.

    1977-01-01

    A Marshall Coil was fabricated by the LASL CMB-6 Materials Technology Group for use in an electrical testing program to evaluate the Marshall Coil concept. The coil is basically a hat-shaped epoxy insulator which was electroplated with copper on all surfaces, and a complex conductor pattern was machined out of the copper. The brim of the coil is approximately 84 cm diameter and the crown is 24 cm high. Other techniques for fabricating Marshall Coils were studied, the one selected being that which was felt to offer the best chance of success on a one-time basis. Alternate proposals involved (a) the potting of a freestanding copper insulator array in epoxy resin, and (b) inlaying stamped copper conductor sections in the slots of a machined epoxy insulator

  18. Thermal conductive epoxy enhanced by nanodiamond-coated carbon nanotubes

    Science.gov (United States)

    Zhao, Bo; Jiang, Guohua

    2017-11-01

    Nanodiamond (ND) particles were coated on the surface of carbon nanotubes (CNTs) by chemical reactions. Reliable bonding was formed by the combination of acyl chloride on NDs and amine group on CNTs. ND coated CNTs (CNT-ND) were dispersed into epoxy to fabricate thermal conductive resins. The results show that the surface energy of CNTs is decreased by the coated NDs, which is contributed to the excellent dispersion of CNT-NDs in the epoxy matrix. The heat-transfer channels were built by the venous CNTs cooperating with the coated NDs, which not only plays an effective role of heat conduction for CNTs and NDs, but also avoids the electrical leakage by the protection of NDs surrounding outside of CNTs. Electrical and thermal conductance measurements demonstrate that the influence of the CNT-ND incorporation on the electrical conductance is minor, however, the thermal conductivity is improved significantly for the epoxy filled with CNT-ND.[Figure not available: see fulltext.

  19. Novel Epoxy Activated Hydrogels for Solving Lactose Intolerance

    Directory of Open Access Journals (Sweden)

    Magdy M. M. Elnashar

    2014-01-01

    Full Text Available “Lactose intolerance” is a medical problem for almost 70% of the world population. Milk and dairy products contain 5–10% w/v lactose. Hydrolysis of lactose by immobilized lactase is an industrial solution. In this work, we succeeded to increase the lactase loading capacity to more than 3-fold to 36.3 U/g gel using epoxy activated hydrogels compared to 11 U/g gel using aldehyde activated carrageenan. The hydrogel’s mode of interaction was proven by FTIR, DSC, and TGA. The high activity of the epoxy group was regarded to its ability to attach to the enzyme’s –SH, –NH, and –OH groups, whereas the aldehyde group could only bind to the enzyme’s –NH2 group. The optimum conditions for immobilization such as epoxy chain length and enzyme concentration have been studied. Furthermore, the optimum enzyme conditions were also deliberated and showed better stability for the immobilized enzyme and the Michaelis constants, Km and Vmax, were doubled. Results revealed also that both free and immobilized enzymes reached their maximum rate of lactose conversion after 2 h, albeit, the aldehyde activated hydrogel could only reach 63% of the free enzyme. In brief, the epoxy activated hydrogels are more efficient in immobilizing more enzymes than the aldehyde activated hydrogel.

  20. Novel epoxy activated hydrogels for solving lactose intolerance.

    Science.gov (United States)

    Elnashar, Magdy M M; Hassan, Mohamed E

    2014-01-01

    "Lactose intolerance" is a medical problem for almost 70% of the world population. Milk and dairy products contain 5-10% w/v lactose. Hydrolysis of lactose by immobilized lactase is an industrial solution. In this work, we succeeded to increase the lactase loading capacity to more than 3-fold to 36.3 U/g gel using epoxy activated hydrogels compared to 11 U/g gel using aldehyde activated carrageenan. The hydrogel's mode of interaction was proven by FTIR, DSC, and TGA. The high activity of the epoxy group was regarded to its ability to attach to the enzyme's -SH, -NH, and -OH groups, whereas the aldehyde group could only bind to the enzyme's -NH2 group. The optimum conditions for immobilization such as epoxy chain length and enzyme concentration have been studied. Furthermore, the optimum enzyme conditions were also deliberated and showed better stability for the immobilized enzyme and the Michaelis constants, K m and V max, were doubled. Results revealed also that both free and immobilized enzymes reached their maximum rate of lactose conversion after 2 h, albeit, the aldehyde activated hydrogel could only reach 63% of the free enzyme. In brief, the epoxy activated hydrogels are more efficient in immobilizing more enzymes than the aldehyde activated hydrogel.

  1. Tailoring of epoxy material properties

    NARCIS (Netherlands)

    Nakka, J.S.

    2010-01-01

    This research work is aimed to understand the effect of resin chemistry on the physical properties (e.g. moduli, viscoelasticity, moisture uptake, coefficient of thermal expansion) of cured aromatic epoxy-amine thermoset resins. This understanding will result into a good first approximation of the

  2. Rheological and morphological properties of graphene-epoxy nanocomposites

    Science.gov (United States)

    Nobile, Maria Rossella; Raimondo, Marialuigia; Lafdi, Khalid; Guadagno, Liberata

    2016-05-01

    In this paper the rheological and morphological properties of an epoxy resin filled with graphene-based nanoparticles have been investigated. Two samples of partially exfoliated graphite (pEG) and carboxylated partially exfoliated graphite (CpEG), differing essentially for the content of carboxylated groups, are used. The percentage of exfoliated graphite is slightly different for the two samples: 56% for pEG and and 60% for CpEG. Exfoliated graphite is prepared using traditional acid intercalation followed by a sudden treatment at high temperature (900°C). The epoxy matrix is prepared by mixing a tetrafunctional precursor with a reactive diluent which produces a significant decrease in the viscosity of the epoxy precursor so that the dispersion step of nanofillers in the matrix can easily occur. The hardener agent, the 4,4-diaminodiphenyl sulfone (DDS), is added at a stoichiometric concentration with respect to all the epoxy rings. The inclusion of the pEG and CpEG samples in the formulated epoxy mixture significantly modifies the rheological behaviour of the mixture itself. The epoxy mixture, indeed, shows a Newtonian behavior; on the contrary the complex viscosity of the nanocomposites clearly shows a shear thinning behavior at 3 wt % of pEG content and at 0.75 wt% of CpEG content. The increase in complex viscosity with the increasing of pEG and CpEG content is mostly caused by a dramatic increase in the storage modulus of the nanocomposites. All the graphene-based epoxy mixtures are cured by a two-stage curing cycles: a first isothermal stage is carried out at the lower temperature of 125°C for 1 hour and, then, a second isothermal stage at the higher temperature of 200°C for 3 hours. The different morphology shown by the two pEG and CpEG samples is consistent with the difference in the percentage of exfoliation degree and well correlates with the rheological behavior of investigated graphene-epoxy nanocomposites.

  3. Characterization of nanostructured epoxy networks modified with isocyanate-terminated liquid polybutadiene.

    Science.gov (United States)

    Soares, Bluma G; Dahmouche, Karim; Lima, Verônica D; Silva, Adriana A; Caplan, Shalimar P C; Barcia, Fabio L

    2011-06-15

    Polybutadiene-block-epoxy prepolymer (DGEBA-b-PBNCO) copolymers with multi-branched topological structure were prepared by reacting isocyanate-multifunctionalized liquid polybutadiene (PBNCO) with DGEBA prepolymer and used to develop nanostructured rubber-modified epoxy thermosets cured with triethylene-tetramine (TETA) as the aliphatic amine. The nanoscopic structure was obtained with the addition of as high as 20 phr of rubber component and successfully demonstrated by transmission electron microscopy (TEM) and small-angle X-ray scattering (SAXS). The glass transition temperature of the rubber-modified epoxy networks was slightly higher than the neat epoxy system. In addition, a unique combination of outstanding toughness and increased modulus and T(g) was achieved in these modified systems, which was attributed to the peculiar morphology associated with a strong interfacial adhesion imparted by the reaction between the isocyanate and hydroxyl groups present in the PBNCO and epoxy resin, respectively. The effect of the PBNCO on the gelation time of the epoxy/TETA system was investigated by rheological techniques. The NCO-functionalized polybutadiene decreased the gelation time, indicating an accelerating effect on the curing process, probably because of the urethane groups formed by the reaction between PBNCO and the epoxy resin during the PB-b-ER block copolymer preparation. Copyright © 2011 Elsevier Inc. All rights reserved.

  4. Cell surface-bound heat shock protein 70 (Hsp70) mediates perforin-independent apoptosis by specific binding and uptake of granzyme B.

    Science.gov (United States)

    Gross, Catharina; Koelch, Walter; DeMaio, Antonio; Arispe, Nelson; Multhoff, Gabriele

    2003-10-17

    Cell surface-bound heat shock protein 70 (Hsp70) renders tumor cells more sensitive to the cytolytic attack mediated by natural killer (NK) cells. A 14-amino acid Hsp70 sequence, termed TKD (TKDNNLLGRFELSG, aa450-463) could be identified as the extracellular localized recognition site for NK cells. Here, we show by affinity chromatography that both, full-length Hsp70-protein and Hsp70-peptide TKD, specifically bind a 32-kDa protein derived from NK cell lysates. The serine protease granzyme B was uncovered as the 32-kDa Hsp70-interacting protein using matrix-assisted laser desorption ionization time-of-flight mass peptide fingerprinting. Incubation of tumor cells with increasing concentrations of perforin-free, isolated granzyme B shows specific binding and uptake in a dose-dependent manner and results in initiation of apoptosis selectively in tumor cells presenting Hsp70 on the cell surface. Remarkably, Hsp70 cation channel activity was also determined selectively in purified phospholipid membranes of Hsp70 membrane-positive but not in membrane-negative tumor cells. The physiological role of our findings was demonstrated in primary NK cells showing elevated cytoplasmic granzyme B levels following contact with TKD. Furthermore, an increased lytic activity of Hsp70 membrane-positive tumor cells could be associated with granzyme B release by NK cells. Taken together we propose a novel perforin-independent, granzyme B-mediated apoptosis pathway for Hsp70 membrane-positive tumor cells.

  5. Mesenchymal stromal cells induce epithelial-to-mesenchymal transition in human colorectal cancer cells through the expression of surface-bound TGF-β.

    Science.gov (United States)

    Mele, Valentina; Muraro, Manuele G; Calabrese, Diego; Pfaff, Dennis; Amatruda, Nunzia; Amicarella, Francesca; Kvinlaug, Brynn; Bocelli-Tyndall, Chiara; Martin, Ivan; Resink, Therese J; Heberer, Michael; Oertli, Daniel; Terracciano, Luigi; Spagnoli, Giulio C; Iezzi, Giandomenica

    2014-06-01

    Mesenchymal stem/stromal cells (MSC) are multipotent precursors endowed with the ability to home to primary and metastatic tumor sites, where they can integrate into the tumor-associated stroma. However, molecular mechanisms and outcome of their interaction with cancer cells have not been fully clarified. In this study, we investigated the effects mediated by bone marrow-derived MSC on human colorectal cancer (CRC) cells in vitro and in vivo. We found that MSC triggered epithelial-to-mesenchymal transition (EMT) in tumor cells in vitro, as indicated by upregulation of EMT-related genes, downregulation of E-cadherin and acquisition of mesenchymal morphology. These effects required cell-to-cell contact and were mediated by surface-bound TGF-β newly expressed on MSC upon coculture with tumor cells. In vivo tumor masses formed by MSC-conditioned CRC cells were larger and characterized by higher vessel density, decreased E-cadherin expression and increased expression of mesenchymal markers. Furthermore, MSC-conditioned tumor cells displayed increased invasiveness in vitro and enhanced capacity to invade peripheral tissues in vivo. Thus, by promoting EMT-related phenomena, MSC appear to favor the acquisition of an aggressive phenotype by CRC cells. © 2013 The Authors. Published by Wiley Periodicals, Inc. on behalf of UICC.

  6. Visible Light Curable Restorative Composites for Dental Applications Based on Epoxy Monomer.

    Science.gov (United States)

    Vitale, Alessandra; Sangermano, Marco; Bongiovanni, Roberta; Burtscher, Peter; Moszner, Norbert

    2014-01-20

    A cationic photo-curable cycloaliphatic epoxy resin has been investigated as reactive monomer in blue light crosslinking process. We have demonstrated that camphorquinone is able to abstract labile hydrogen from the epoxy monomer, giving rise to the formation of carbon-centered radicals that are oxidized by the onium salt; a complete epoxy group conversion was reached after 50 s of irradiation. The presence of water up to 1 wt% was tolerated without any important detrimental effect on the kinetics of light-curing. The presence of the inorganic filler up to 65 wt% did not significantly influence the curing process.

  7. Visible Light Curable Restorative Composites for Dental Applications Based on Epoxy Monomer

    Directory of Open Access Journals (Sweden)

    Alessandra Vitale

    2014-01-01

    Full Text Available A cationic photo-curable cycloaliphatic epoxy resin has been investigated as reactive monomer in blue light crosslinking process. We have demonstrated that camphorquinone is able to abstract labile hydrogen from the epoxy monomer, giving rise to the formation of carbon-centered radicals that are oxidized by the onium salt; a complete epoxy group conversion was reached after 50 s of irradiation. The presence of water up to 1 wt% was tolerated without any important detrimental effect on the kinetics of light-curing. The presence of the inorganic filler up to 65 wt% did not significantly influence the curing process.

  8. Hearing loss in workers exposed to epoxy adhesives and noise: a cross-sectional study.

    Science.gov (United States)

    Yang, Hsiao-Yu; Shie, Ruei-Hao; Chen, Pau-Chung

    2016-02-18

    Epoxy adhesives contain organic solvents and are widely used in industry. The hazardous effects of epoxy adhesives remain unclear. The objective of this study was to investigate the risk of hearing loss among workers exposed to epoxy adhesives and noise. Cross-sectional study. For this cross-sectional study, we recruited 182 stone workers who were exposed to both epoxy adhesives and noise, 89 stone workers who were exposed to noise only, and 43 workers from the administrative staff who had not been exposed to adhesives or noise. We obtained demographic data, occupational history and medical history through face-to-face interviews and arranged physical examinations and pure-tone audiometric tests. We also conducted walk-through surveys in the stone industry. A total of 40 representative noise assessments were conducted in 15 workplaces. Air sampling was conducted at 40 workplaces, and volatile organic compounds were analysed using the Environmental Protection Agency (EPA) TO-15 method. The mean sound pressure level was 87.7 dBA (SD 9.9). The prevalence of noise-induced hearing loss was considerably increased in the stone workers exposed to epoxy adhesives (42%) compared with the stone workers who were not exposed to epoxy adhesives (21%) and the administrative staff group (9.3%). A multivariate logistic regression analysis revealed that exposure to epoxy adhesives significantly increased the risk of hearing loss between 2 and 6 kHz after adjusting for age. Significant interactions between epoxy adhesives and noise and hearing impairment were observed at 3, 4 and 6 kHz. Epoxy adhesives exacerbate hearing impairment in noisy environments, with the main impacts occurring in the middle and high frequencies. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

  9. Epoxy Resins in Electron Microscopy

    Science.gov (United States)

    Finck, Henry

    1960-01-01

    A method of embedding biological specimens in araldite 502 (Ciba) has been developed for materials available in the United States. Araldite-embedded tissues are suitable for electron microscopy, but the cutting qualities of the resin necessitates more than routine attention during microtomy. The rather high viscosity of araldite 502 also seems to be an unnecessary handicap. The less viscous epoxy epon 812 (Shell) produces specimens with improved cutting qualities, and has several features—low shrinkage and absence of specimen damage during cure, minimal compression of sections, relative absence of electron beam-induced section damage, etc.—which recommends it as a routine embedding material. The hardness of the cured resin can be easily adjusted by several methods to suit the materials embedded in it. Several problems and advantages of working with sections of epoxy resins are also discussed. PMID:13822825

  10. Flammability of Epoxy Resins Containing Phosphorus

    Science.gov (United States)

    Hergenrother, P. M.; Thompson, C. M.; Smith, J. G.; Connell, J. W.; Hinkley, J. A.

    2005-01-01

    As part of a program to develop fire-resistant exterior composite structures for future subsonic commercial and general aviation aircraft, flame-retardant epoxy resins are under investigation. Epoxies and their curing agents (aromatic diamines) containing phosphorus were synthesized and used to prepare epoxy formulations. Phosphorus was incorporated within the backbone of the epoxy resin and not used as an additive. The resulting cured neat epoxy formulations were characterized by thermogravimetric analysis, propane torch test, elemental analysis, microscale combustion calorimetry, and fire calorimetry. Several formulations showed excellent flame retardation with phosphorous contents as low as 1.5% by weight. The fracture toughness and compressive strength of several cured formulations showed no detrimental effect due to phosphorus content. The chemistry and properties of these new epoxy formulations are discussed.

  11. Epoxy resins in the construction industry.

    Science.gov (United States)

    Spee, Ton; Van Duivenbooden, Cor; Terwoert, Jeroen

    2006-09-01

    Epoxy resins are used as coatings, adhesives, and in wood and concrete repair. However, epoxy resins can be highly irritating to the skin and are strong sensitizers. Some hardeners are carcinogenic. Based on the results of earlier Dutch studies, an international project on "best practices,"--Epoxy Code--with epoxy products was started. Partners were from Denmark, Germany, the Netherlands, and the UK. The "Code" deals with substitution, safe working procedures, safer tools, and skin protection. The feasibility of an internationally agreed "ranking system" for the health risks of epoxy products was studied. Such a ranking system should inform the user of the harmfulness of different epoxies and stimulate research on less harmful products by product developers.

  12. Occupational allergic contact dermatitis caused by epoxy chemicals: occupations, sensitizing products, and diagnosis.

    Science.gov (United States)

    Aalto-Korte, Kristiina; Pesonen, Maria; Suuronen, Katri

    2015-12-01

    Epoxy products are among the most common causes of occupational allergic contact dermatitis. Diglycidyl ether of bisphenol A resin (DGEBA-R) is the most important sensitizer in epoxy systems. To describe patients with occupational allergic contact dermatitis caused by epoxy products. Patients with allergic reactions to epoxy chemicals were chosen from test files (January 1991 to June 2014). Only patients with occupational contact allergy to some component of epoxy resin systems were included. We analysed patch test results, occupation, symptoms, and exposure data. We found a total of 209 cases with occupational contact allergy to epoxy chemicals. The largest occupational groups were painters (n = 41), floor layers (n = 19), electrical industry workers (n = 19), tile setters (n = 16), and aircraft industry workers (n = 15). A total of 82% of the patients reacted to DGEBA-R. Diagnosis of the DGEBA-R-negative patients required testing with m-xylylenediamine, N,N'-tetraglycidyl-4,4'-methylenedianiline, 1,4-butanediol diglycidyl ether, 2,4,6-tris-(dimethylaminomethyl)phenol, diglycidyl ether of bisphenol F resin, N,N'-diglycidyl-4-glycidyloxyaniline, isophoronediamine, 4,4'-diaminodiphenylmethane, diethylenetriamine, and cresyl glycidyl ether. The hands/upper extremities were most commonly affected (69%), but facial symptoms were also frequent (60%). Allergic contact dermatitis caused by to epoxy products cannot always be diagnosed by the use of commercial test substances. Workplace products need to be tested. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  13. Single-component and fast-curing epoxy resin for liquid composite molding processes

    Directory of Open Access Journals (Sweden)

    Wang Yiru

    2017-01-01

    Full Text Available Development of single-component and fast-curing epoxy resins is highly desired for many industry applications. In this work, we report an epoxy system based on diglycidyl ether of bisphenol A (DGEBA and 1-(2-cyanoethyl-2-ethyl-4- methylimidazole (1C2E4MIM. The inductive effect of electron-withdrawing cyano group distinctly increases the latency of 1C2E4MIM without sacrificing the curing rate. The results of differential scanning calorimeter (DSC and dynamic mechanical analysis (DMA measurements indicate DGEBA/1C2E4MIM epoxy system can be fully cured in 15 min. The rheological, thermal and mechanical properties of DGEBA/1C2E4MIM epoxy system were studied in detail. The results show that the shelf life of this epoxy system is more than 4 days at room temperature and more than 6 months at -18 °C. The cured epoxy resins show high glass transition temperature (>155 °C, tensile strength (>80 MPa as well as excellent moist heat resistance. Finally, carbon fiber-reinforced polymer composites (CFRPs were fabricated using this epoxy system as matrix via vacuum assisted resin infusion (VARI process. The mechanical properties of CFRPs, including tensile, flexural, compressive and interlaminar shear properties, were investigated.

  14. Thermally activated, single component epoxy systems

    KAUST Repository

    Unruh, David A.

    2011-08-23

    A single component epoxy system in which the resin and hardener components found in many two-component epoxies are combined onto the same molecule is described. The single molecule precursor to the epoxy resin contains both multiple epoxide moieties and a diamine held latent by thermally degradable carbamate linkages. These bis-carbamate "single molecule epoxies" have an essentially infinite shelf life and access a significant range in curing temperatures related to the structure of the carbamate linkages used. © 2011 American Chemical Society.

  15. Comparison of the Effect of Addition of Cyanoacrylate, Epoxy Resin, and Gum Arabic on Surface Hardness of Die Stone.

    Science.gov (United States)

    Tripathi, Arvind; Gupta, Ashutosh; Bagchi, Soumyojeet; Mishra, Lallan; Gautam, Abhina; Madhok, Riti

    2016-04-01

    To observe the effects of incorporating cyanoacrylate, epoxy resins, and gum arabic on the abrasion resistance of type IV gypsum die materials. Forty specimens were prepared and divided into four groups (10 specimens in each group), namely group A (control), group B (die stone mixed with cyanoacrylate), group C (die stone mixed with epoxy resin), group D (die stone mixed with gum arabic). All the specimens were subjected to abrasion testing, wear volume analysis, Fourier transform infrared spectroscopy (FT-IR), and scanning electron microscope (SEM) analysis. Abrasion testing showed maximum wear in the control group and minimum wear in the gum arabic group. Intergroup differences were statistically significant (p Epoxy resins are powerful adhesives, but they attain their full efficiency when cured with heat. Cyanoacrylate and epoxy resin displayed poor physical bonding, primarily because of inhomogeneity. © 2015 by the American College of Prosthodontists.

  16. Functionalization of Multi-Walled Carbon Nanotube and Mechanical Property of Epoxy-Based Nanocomposite

    OpenAIRE

    Francisco, Wesley; Ferreira, Filipe Vargas; Ferreira, Eduardo Vargas; Cividanes, Luciana de Simone; Coutinho, Aparecido dos Reis; Thim, Gilmar Patrocínio

    2015-01-01

    ABSTRACT: The focus of this study is to evaluate the effect of carboxyl and amino functionalization of multiwalled carbon nanotubes on the mechanical property of the epoxy resin filled with modified carbon nanotubes. The carbon nanotubes were treated with sulfuric and nitric acids and also with hexamethylenediamine. The presence of acid and amine chemical groups on the carbon nanotube surface was confirmed by X-ray photoelectron spectroscopy. The composites were produced with epoxy resin and ...

  17. Silane coupling agent for attaching fusion-bonded epoxy to steel.

    Science.gov (United States)

    Tchoquessi Diodjo, Madeleine R; Belec, Lénaïk; Aragon, Emmanuel; Joliff, Yoann; Lanarde, Lise; Perrin, François-Xavier

    2013-07-24

    We describe the possibility of using γ-aminopropyltriethoxysilane (γ-APS) to increase the durability of epoxy powder coating/steel joints. The curing temperature of epoxy powder coatings is frequently above 200 °C, which is seen so far as a major limitation for the use of the heat-sensitive aminosilane coupling agent. Despite this limitation, we demonstrate that aminosilane is a competitive alternative to traditional chromate conversion to enhance the durability of epoxy powder coatings/steel joints. Fourier-transform reflection-absorption infrared spectroscopy (FT-RAIRS), X-ray photoelectron spectroscopy (XPS), and atomic force microscopy (AFM) were used to identify the silane deposition conditions that influence the adhesion of epoxy powder coatings on steel. We show that AFM analysis provides highly sensitive measurements of mechanical property development and, as such, the degree of condensation of the silane. The joint durability in water at 60 °C was lower when the pH of the γ-APS solution was controlled at 4.6 using formic acid, rather than that at natural pH (10.6). At the curing temperature of 220 °C, oxidation of the carbon adjacent to the amine headgroup of γ-APS gives amide species by a pseudofirst-order kinetics. However, a few amino functionalities remain to react with oxirane groups of epoxy resin and, thus, strengthen the epoxy/silane interphase. The formation of ammonium formate in the acidic silane inhibits the reaction between silane and epoxy, which consequently decreases the epoxy/silane interphase cohesion. We find that the nanoroughness of silane deposits increases with the cure temperature which is beneficial to the wet stability of the epoxy/steel joints, due to increased mechanical interlocking.

  18. The study of radiation effect on 127-epoxy resin adhesive and its components

    International Nuclear Information System (INIS)

    Zhong Zhijing; Luo Shikai; Fu Yibei; Luo Shunzhong

    2001-01-01

    127-epoxy resin adhesive and its components: E-44 epoxy resin, dibutyl-o-phthalate and anhydrous ethylenediamine were irradiated with γ ray in air, nitrogen or vacuum at ambient temperature respectively. The gaseous products such as hydrogen, methane and carbon dioxide were examined by means of GC. Remarkable effect of ambiences and dose on γ radiated degradation of these specimen were found. The results indicated that the content of gaseous products increased with dose, but changed with ambiences. The forming of carbon dioxide was not only determined by the amount of oxygen in ambience, but also by whether the specimens structure contained oxygenous groups or not. It was shown that there were good linear increasing relationships between dose and the concentration of gaseous products hydrogen and methane for 127-epoxy resin adhesive, and methane for dibutyl-o-phthalate. All above indicated low radiation-resistance of 127-epoxy resin adhesive

  19. Epoxy-based carbon nanotubes reinforced composites

    CSIR Research Space (South Africa)

    Kesavan Pillai, Sreejarani

    2011-04-01

    Full Text Available Epoxy or polyepoxide is a thermosetting epoxide polymer that cures (polymerizes and cross-links) when mixed with a curing agent or "hardener". Most common epoxy resins are produced from a reaction between epichlorohydrin and bisphenol-A. A newly...

  20. [Delayed asthma bronchiale due to epoxy resin].

    Science.gov (United States)

    Authried, Georg; Al-Asadi, Haifaa; Møller, Ulla; Sherson, David Lee

    2013-10-28

    Epoxy resin is a low molecular weight agent, which can cause both acute and delayed allergic reactions. However, it is known causing skin reactions with direct or airborne contact. Rarely it can cause airway reactions like asthma bronchiale. We describe a case of a windmill worker who developed delayed asthma bronchiale due to airborne contact with epoxy resin.

  1. Thermoset epoxy polymers from renewable resources

    Science.gov (United States)

    East, Anthony [Madison, NJ; Jaffe, Michael [Maplewood, NJ; Zhang, Yi [Harrison, NJ; Catalani, Luiz H [Carapicuiba, BR

    2009-11-17

    Novel thermoset epoxy polymers using the bisglycidyl ethers of anhydrosugars, such as isosorbide, isomannide, and isoidide, are disclosed. The bisglycidyl ethers are useful as substitutes for bisphenol A in the manufacture of thermoset epoxy ethers. The anhydrosugars are derived from renewable sources and the bisglycidyl ethers are not xenoestrogenic and the thermoset curing agents are likewise derived form renewable resources.

  2. Dielectric properties of nanosilica filled epoxy nanocomposites

    Indian Academy of Sciences (India)

    M G Veena

    This paper presents the development of epoxy-silica nanocomposites and characterized for dielectric properties. The effect of ... However, at higher silica loading TEM showed inter-contactity of the particles. The dielectric constant (e. 0. ) ..... of the mechanical and permeability properties of nano- and micron-TiO2 filled epoxy ...

  3. Electron-beam curing of epoxy resins

    Indian Academy of Sciences (India)

    Electron-beam (e-beam) induced polymerization of epoxy resins proceeds via cationic mechanism in presence of suitable photoinitiator. Despite good thermal properties and significant processing advantages, epoxy-based composites manufactured using e-beam curing suffer from low compressive strength, poor ...

  4. Astmatisk senreaktion efter kontakt med epoxy

    DEFF Research Database (Denmark)

    Authried, Georg; Al-Asadi, Haifaa; Møller, Ulla

    2013-01-01

    Epoxy resin is a low molecular weight agent, which can cause both acute and delayed allergic reactions. However, it is known causing skin reactions with direct or airborne contact. Rarely it can cause airway reactions like asthma bronchiale. We describe a case of a windmill worker who developed...... delayed asthma bronchiale due to airborne contact with epoxy resin....

  5. EPOXI at comet Hartley 2.

    Science.gov (United States)

    A'Hearn, Michael F; Belton, Michael J S; Delamere, W Alan; Feaga, Lori M; Hampton, Donald; Kissel, Jochen; Klaasen, Kenneth P; McFadden, Lucy A; Meech, Karen J; Melosh, H Jay; Schultz, Peter H; Sunshine, Jessica M; Thomas, Peter C; Veverka, Joseph; Wellnitz, Dennis D; Yeomans, Donald K; Besse, Sebastien; Bodewits, Dennis; Bowling, Timothy J; Carcich, Brian T; Collins, Steven M; Farnham, Tony L; Groussin, Olivier; Hermalyn, Brendan; Kelley, Michael S; Kelley, Michael S; Li, Jian-Yang; Lindler, Don J; Lisse, Carey M; McLaughlin, Stephanie A; Merlin, Frédéric; Protopapa, Silvia; Richardson, James E; Williams, Jade L

    2011-06-17

    Understanding how comets work--what drives their activity--is crucial to the use of comets in studying the early solar system. EPOXI (Extrasolar Planet Observation and Deep Impact Extended Investigation) flew past comet 103P/Hartley 2, one with an unusually small but very active nucleus, taking both images and spectra. Unlike large, relatively inactive nuclei, this nucleus is outgassing primarily because of CO(2), which drags chunks of ice out of the nucleus. It also shows substantial differences in the relative abundance of volatiles from various parts of the nucleus.

  6. Cell surface-bound TIMP3 induces apoptosis in mesenchymal Cal78 cells through ligand-independent activation of death receptor signaling and blockade of survival pathways.

    Directory of Open Access Journals (Sweden)

    Christina Koers-Wunrau

    exclusively cell surface-bound endogenous TIMP3 induces apoptosis in mesenchymal Cal78 cells through ligand-independent activation of death receptor signaling and blockade of survival signaling pathways.

  7. Control of epoxy creep using graphene.

    Science.gov (United States)

    Zandiatashbar, Ardavan; Picu, Catalin R; Koratkar, Nikhil

    2012-06-11

    The creep behavior of epoxy-graphene platelet (GPL) nanocomposites with different weight fractions of filler is investigated by macroscopic testing and nanoindentation. No difference is observed at low stress and ambient temperature between neat epoxy and nanocomposites. At elevated stress and temperature the nanocomposite with the optimal weight fraction, 0.1 wt% GPLs, creeps significantly less than the unfilled polymer. This indicates that thermally activated processes controlling the creep rate are in part inhibited by the presence of GPLs. The phenomenon is qualitatively similar at the macroscale and in nanoindentation tests. The results are compared with the creep of epoxy-single-walled (SWNT) and multi-walled carbon nanotube (MWNT) composites and it is observed that creep in both these systems is similar to that in pure epoxy, that is, faster than creep in the epoxy-GPL system considered in this work. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  8. COVALENT IMMOBILIZATION OF INVERTASE ON EPOXY-ACTIVATED POLYANILINE FILMS

    Directory of Open Access Journals (Sweden)

    Loredana Vacareanu

    2013-08-01

    Full Text Available The growing interest in manufacturing and use of biosensors is their rapid and selective detection of the target analyte. The immobilization of the enzymes, onto the appropriate matrix is the key-step in the construction of biosensing devices, considerably affecting its performance. In this study, new polyaniline bearing epoxy groups was synthesized by electrochemical polymerization reactions, as adherent, green film deposited on electrode surface, and was further used as immobilization matrix for invertase enzyme. The immobilization was carried out by condensation reactions between the amino groups of the enzyme molecules and the epoxy groups of polyaniline film. The covalent attachment was achieved by simple immersing the epoxy-activated polyaniline in acetate buffer solution (10 mM, pH 6.0 containing 2mg/mL invertase, for 24 h at 4 ºC, by continuous stirring. The polyaniline films thus obtained were analyzed before and after the invertase attachment, by using FT-IR spectroscopy and SEM microscopy. The presence of the invertase was evaluated by measuring their activity, using UV-Vis spectroscopy, in the presence of a known amount of sucrose as a substrate. These tests, performed for three times under the same conditions, revealed that even after five washes of the polyaniline /invertase electrode to remove the unbounded enzyme, the enzyme remain attached on the polyaniline film, being able to hydrolyze the sucrose presented in the assay solutions.

  9. Comportamento de cura de adesivo epoxídico contendo grupo mercaptana avaliado por espectroscopia no infravermelho (MIR/NIR e calorimetria exploratória diferencial (DSC Cure behavior of epoxy adhesive containig mercaptan group evaluated by infrared spectroscopy (MIR/NIR and differential scanning calorimetry (DSC

    Directory of Open Access Journals (Sweden)

    Hilzette P. C. Andrade

    2008-01-01

    Full Text Available No presente trabalho, a flexibilidade de um adesivo epoxídico contendo diglicidiléter de bisfenol A (DGEBA e dietilenotriamina (DETA como agente de cura foi modificada pela adição de um segundo componente contendo grupos mercaptana (CAPCURE. A adição de amianto ao adesivo contendo CAPCURE também foi avaliada. As reações entre os grupos epoxídicos e os grupos amina, assim como entre os grupos epoxídicos e os grupos mercaptana, foram estudadas nas regiões espectrais do infravermelho médio (MIR e próximo (NIR. Observou-se que o amianto não interfere nas reações de cura e que a espectroscopia FT-NIR evidencia melhor as alterações espectrométricas ocorridas durante as reações em relação à análise FT-MIR. O tempo das reações de cura foi monitorado por calorimetria exploratória diferencial (DSC, observando-se que a introdução do CAPCURE acelerou a cura da resina. A energia de ativação (Ea das reações de cura foi obtida pelos métodos de Barrett e Borchardt-Daniels. Os adesivos contendo CAPCURE mostraram Ea em torno de 30 kJ.mol-1, enquanto o adesivo DGEBA/DETA apresentou Ea de 46 kJ.mol-1, ambas calculadas pelo método de Barrett.In the present work, the flexibility of an epoxy adhesive containing diglycidylether of bisphenol-A (DGEBA and diethylenetriamine (DETA as curing agent was changed by the addition of a second component containing mercaptan groups (CAPCURE. The addition of asbestos as a filler in the adhesive containing CAPCURE was also evaluated. Epoxy-amine and epoxy-mercaptan reactions were studied in NIR and MIR spectral regions. The filler addition did not cause influence on the cure reactions and spectrometric changes of cure reactions could be better observed by FT-NIR than FT-MIR analysis. The cure reaction time was monitored by DSC experiments and it was observed that the introduction of CAPCURE accelerated the cure reaction. The activation energies (Ea of curing reactions were obtained using Barrett

  10. Self-Healing Photocurable Epoxy/thiol-ene Systems Using an Aromatic Epoxy Resin

    Directory of Open Access Journals (Sweden)

    Ricardo Acosta Ortiz

    2016-01-01

    Full Text Available A rapid and efficient method to obtain self-healing epoxy resins is discussed. This method is based on the use of a thiol-disulfide oligomer obtained by partial oxidation of a multifunctional thiol using a hypervalent iodine (III compound as oxidant. The oligomer was characterized by Fourier transform infrared spectroscopy (FTIR, Raman and nuclear magnetic resonance spectroscopies, and gel permeation chromatography (GPC. The oligomer was a joint component of the thiol-ene system along with a tetra-allyl-functionalized curing agent. The kinetics of the photopolymerization of diglycidylether of bisphenol A (DGEBA revealed that conversions of the epoxy groups as high as 80% were achieved in only 15 minutes by increasing the concentration of the thiol-ene system in the formulation. The disulfide bonds introduced in the copolymer using the thiol-disulfide oligomer allowed the repairing of the test specimens in as little as 10 minutes when the specimens were heated at 80°C or for 500 minutes at room temperature. The analysis of the mechanical properties using dynamic mechanical analysis (DMA showed that the specimens displayed a healing efficiency up to 111% compared with the unhealed specimens, depending on the amount of polythioethers present in the copolymer.

  11. Imide modified epoxy matrix resins

    Science.gov (United States)

    Scola, D. A.

    1984-01-01

    The results of a program designed to develop tough imide modified epoxy resins cured by bisimide amine (BIA) hardeners are described. State-of-the-art epoxides MY720 and DER383 were used, and four bismide amines were evaluated. These were the BIA's derived from the 6F anhydride (4,4'-(hexafluoroisopropylidene) bis(phthalic anhydride) and the diamines 3,3'-diaminodiphynyl sulfone, 4,4'-oxygianiline, 4,4'-methylene dianiline, and 1,12-dodecane diamine. A key intermediate, designated 6F anhydride, is required for the synthesis of the bisimide amines. Reaction parameters to synthesize a precursor to the 6F anhydride (6FHC) in high yields were investigated. The catalyst trifluoromethane sulfonic acid was studied. Although small scale runs yielded the 6FHC in 50 percent yield, efforts to ranslate these results to a larger scale synthesis gave the 6FHC in only 9 percent yield. Results show that the concept of using bisimide amine as curing agents to improve the toughness properties of epoxies is valid.

  12. Nanosilica reinforced epoxy floor coating composites: preparation and thermophysical characterization

    Directory of Open Access Journals (Sweden)

    Mir Mohammad Alavi Nikje

    2012-01-01

    Full Text Available In this study, flooring grade epoxy/nanoSiO2 nanocomposites were prepared by in-situ polymerization method. Nano silica was treated by coupling agent in order to surface treating and introducing of reactive functional groups to achieving adequate bonding between polar inorganic nano particles and epoxy organic polymer. γ-Aminopropyltriethoxysilane (Amino A-100 was used as an effective and commercially available coupling agent and nano silica treated in acetone media. SEM observations of cured samples revealed that the nano silica was completely dispersed into polymer matrix into nanoscale particles. Thermal and physical properties of prepared samples were investigated and data showed improvements in physical and mechanical properties of the flooring samples in comparison with unfilled resin.

  13. Modified Castor Oil as an Epoxy Resin Curing Agent

    Directory of Open Access Journals (Sweden)

    B. P. Patel

    2004-01-01

    Full Text Available A castor oil, an agricultural product, is an unsaturated material. Hence the castor oil is brominated by bromine liquid. The brominated castor oil (BCO was then reacted with excess of aliphatic diamines viz; ethylene diamine, 1,3-propane diamine and 1,6-hexane diamine. The resultant amino functionalized castor oil (ACO samples were then characterized by elemental analysis, IR spectral study and number of amino groups. All the three ACO samples were then employed for the curing of commercial Brominated epoxy resin. The curing of epoxy resin by ACO was monitored on differential scanning calorimeter (DSC and based on the DSC study their glass fibre reinforced composites (GRC were fabricated. The cured samples (i.e. unreinforced were also subjected to thermo gravimetric analysis (TGA. The chemical, mechanical and electrical properties of the glass fibre reinforced composites (GRC were also evaluated.

  14. The application of epoxy resin coating in grounding grid

    Science.gov (United States)

    Hu, Q.; Chen, Z. R.; Xi, L. J.; Wang, X. Y.; Wang, H. F.

    2018-01-01

    Epoxy resin anticorrosion coating is widely used in grounding grid corrosion protection because of its wide range of materials, good antiseptic effect and convenient processing. Based on the latest research progress, four kinds of epoxy anticorrosive coatings are introduced, which are structural modified epoxy coating, inorganic modified epoxy coating, organic modified epoxy coating and polyaniline / epoxy resin composite coating. In this paper, the current research progress of epoxy base coating is analyzed, and prospected the possible development direction of the anti-corrosion coating in the grounding grid, which provides a reference for coating corrosion prevention of grounding materials.

  15. High strain carbon nanotubes based epoxy matrix nanocomposite

    Science.gov (United States)

    Manocha, L. M.; Basak, Arpana; Bhandari, T.; Baishya, T.; Manocha, S.

    2013-06-01

    Multiwalled carbon nanotubes, synthesized by catalytic chemical vapour deposition using xylene as the carbon precursor and ferrocene as the catalyst source, were used as reinforcements for the preparation of carbon nanotubes based epoxy matrix composites. For higher degree of dispersion in the matrix system, oxygen containing groups (C=O, COOH) were attached to the surface of carbon nanotubes by acid treatment followed by rigorous sonication of reinforcement in the matrix system. FTIR confirms the formation of oxygen containing groups on the surface of the carbon nanotubes. Tensile strength and glass transition temperature of the epoxy resin as well as nanocomposite samples have been determined. Carbon nanotubes reinforced composites exhibited ten times higher elongation than as such epoxy mainly due to the strengthening effect of the dispersed nanotubes and the development of moderate interfacial bonding between the resin and the reinforcing agent. A noticeable increase in the glass transition temperature of ˜20°C in the nanocomposites is attributable to the restricted movement of the polymeric chains on account of addition of carbon nanotubes.

  16. Possible formation of interpenetrating polym networks (IPN) by electron beam irradiation of acrylated epoxy resin blends

    International Nuclear Information System (INIS)

    Al-Sheikhyl, M.

    1994-01-01

    Over the last decade, high energy electron beam radiation has been successfully used by a number of laboratories to initiate the polymerization of acrylated epoxides. Unlike the radiation-induced cationic polymerization of epoxides, the polymerization of acrylated epoxides by ionizing radiation propagates by carbon-centered free radicals through the unsaturated end groups. In this work, two part epoxy-based resin matrices were cured by a two-step process; (1) In the first step, an electron beam pre-cure of the matrix was used to produce form stability; then (2) a thermal cycle was employed to complete the cure. The ultimate objective of this work is to provide a controlled epoxy polymerization reaction through the blending of fully unsaturated epoxy with an unmodified epoxy. Such a blended resin contains a component which, when exposed to ionizing radiation, will create a three dimensional structure within the unmodified epoxy resin. Thus, upon thermal curing of the unmodified epoxy resin component within the radiation cured network, an interpenetrating network (IPN) can be formed

  17. Synthesis of Polyurethane/Silica Modified Epoxy Polymer Based on 1,3-Propanediol for Coating Application

    Directory of Open Access Journals (Sweden)

    Lutviasari Nuraini

    2017-11-01

    Full Text Available Studies on the synthesis of polyurethane/silica modified epoxy polymer using 1,3-propanediol has been conducted. Synthesis of polymers made by reaction of tolonate and 1,3-propanediol (ratio NCO/OH=2.5 as the building blocks of polyurethane with diglycidyl ether bisphenol A (DGEBA epoxy and catalyst dibutyltin dilaurate (DBTL.The total weight of the polyurethane used was 20% (w/w of the total epoxy. Based on Fourier Transform Infrared (FTIR and 1H-Nuclear Magnetic Resonance (1H-NMR spectra indicated the existence of a new bond that is formed from the reaction of isocyanate group and hydroxyl group, where the hydroxyl groups derived from epoxy and 1,3-propanediol. The addition of silica (5, 10, and 15% w/w to epoxy into the epoxy-modified polyurethane has been carried out through sol-gel reaction of tetraethyl orthosilicate (TEOS. The isocyanate conversion rate for the addition of silica 5, 10, and 15% are 95.69; 100, and 100%, respectively. The morphology and element identification by Scanning Electron Microscopy/Energy Dispersive X-Ray Analysis (SEM/EDX, showed that Si element has been successfully added in the polymer. From the tensile strength and elongation analysis, also thermal stability analysis using Thermal Gravimetric Analyzer (TGA, the increase of silica amount into the polyurethane modified epoxy did not significantly affect to thermal properties, but decrease the tensile strength of the polymer.

  18. Positron annihilation and polymerization of epoxy

    International Nuclear Information System (INIS)

    Suzuki, T.; Ito, Y.; Endo, K.; Fujita, S.

    1989-01-01

    Positron lifetime measurement has been applied to the investigation of solidification from the liquid state to the solid state in epoxy with different mixing ratios of resin and hardener. It has been shown that the mixing ratios and the physical states of liquid, gel, and solid affect positronium formation. In samples with an excess of hardener, long-lived components were observed in the liquid and gel states, while they disappeared after solidification. Positronium formation in epoxy is strongly affected by the heating process of epoxy samples. (author)

  19. Epoxy resin systems for FGD units

    International Nuclear Information System (INIS)

    Brytus, V.; Puglisi, J.S.

    1984-01-01

    This paper discusses ongoing research work which is directed towards epoxy resins and curing agents which are designed to withstand aggressive environments. This work includes not only a chemical description of the materials involved, but the application testing necessary to verify the usefulness of these systems. It demonstrates that new high performance epoxy systems are superior to those which traditionally come to mind when one thinks epoxy. Finally, it discusses the results of testing designed specifically to screen candidates for use in FGD units

  20. Epoxy Foam Encapsulants: Processing and Dielectric Characterization

    Energy Technology Data Exchange (ETDEWEB)

    Linda Domeier; Marion Hunter

    1999-01-01

    The dielectric performance of epoxy foams was investigated to determine if such materials might provide advantages over more standard polyurethane foams in the encapsulation of electronic assemblies. Comparisons of the dielectric characteristics of epoxy and urethane encapsulant foams found no significant differences between the two resin types and no significant difference between as-molded and machined foams. This study specifically evaluated the formulation and processing of epoxy foams using simple methylhydrosiloxanes as the flowing agent and compared the dielectric performance of those to urethane foams of similar density.

  1. [Contact allergy to epoxy resins plastics based on materials collected by the Nofer Institute of Occupational Medicine].

    Science.gov (United States)

    Kieć-Swierczyńska, Marta; Krecisz, Beata

    2003-01-01

    Of the 5604 patients examined in 1984-2001 for suspected occupational dermatitis, 160 persons (2.8%) showed allergy to epoxy resins plastics. Allergy was more frequent in men (4.9%) than in women (1.2%); in 154 persons, allergy was of occupational etiology (in a group of 160 patients with allergy to epoxy resins, the following proportions were observed: bricklayers, platelayers--17.5%; fitters, turners, machinist millers--13.8%; plastics molders--13.1%; laminators--11.3%; electrical equipment assemblers--10.6%; painters--10.0%). Having compared the frequency of allergy to components of epoxy resins in the years 1984-1993 and 1994-2001, it was found that allergy to resin, reactive diluents and plasticizers was on increase, whereas allergy to amines and acid anhydrides hardeners was on decrease. In a group of 13 chemical compounds entering into the composition of epoxy resins, epoxy resin contributed to the largest number of positive patch tests (77.5% of epoxy-allergic persons). This was followed by triethylenetetramine (23.1%), ethylenediamine (13.1%), phthalic anhydride (8.1%), diethylenetetramine (6.9%) and phenylglycidylether (6.2%). In addition, three patients reacted to both epoxy resin and cycloaliphatic resin.

  2. Epoxy-based carbon nanotubes reinforced composites

    CSIR Research Space (South Africa)

    Kesavan Pillai, Sreejarani

    2011-04-01

    Full Text Available developed strategy offering promising results is to reinforce epoxy matrices with nano-sized organic and inorganic particles such as carbon nanotubes (CNTs), carbon nanofibres (CNFs), nanoclays, metal oxide nanoparticles, etc. and make new materials...

  3. Ionic Liquid Epoxy Composite Cryotanks, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — The objective of this work is to determine the optimal process for manufacturing lightweight linerless cryogenic storage tanks using ionic liquid epoxy composite...

  4. Action of ionizing radiation on epoxy resins

    Energy Technology Data Exchange (ETDEWEB)

    Van de Voorde, M. E.

    1970-12-01

    The resistance of classical and experimental epoxy resins to irradiation was studied. The resistance to irradiation of epoxy resins of diverse compositions as well as the development of resins having a radioresistance that approaches that of certain ceramics are discussed. Sources of irradiation and the techniques of dosimetry used are described. The structures of certain epoxy resins and of hardeners are given. The preparation of these resins and their physical properties is described. The effects of radiation on epoxy resins, as well as conditions of irradiation, and suggested mechanisms for degradation of the irradiated resins are discussed. The relationship between chemical structure of the resins and their physical properties is evaluated. (115 references) (JCB)

  5. IMPROVEMENTS IN EPOXY RESIN EMBEDDING METHODS

    Science.gov (United States)

    Luft, John H.

    1961-01-01

    Epoxy embedding methods of Glauert and Kushida have been modified so as to yield rapid, reproducible, and convenient embedding methods for electron microscopy. The sections are robust and tissue damage is less than with methacrylate embedding. PMID:13764136

  6. Damage evolution in a filled epoxy resin

    International Nuclear Information System (INIS)

    Depoorter, Nicolas; Coutellier, Daniel; Muzic, Markus; Berg-Pollack, Antje; Cai Ye; Zimmermann, Andre

    2006-01-01

    A method is proposed for studying damage evolution in a filled epoxy resin submitted to low-cycle fatigue loading. Transmission electron microscopy analysis was performed, which indicates a damage mechanism that corresponds well to the decreasing slope of the stress-strain hysteresis observed in strain-controlled fatigue experiments. Also, the suggested damage model appears to be suitable for the simulation of strain-controlled cyclic tests and fits the damage evolution of the filled epoxy resin fairly well [de

  7. Functionalization of epoxy esters with alcohols as stoichiometric reagents.

    Science.gov (United States)

    Pavlović, Dona; Modec, Barbara; Dolenc, Darko

    2015-01-01

    Glycidyl esters, frequently employed as reactive groups on polymeric supports, were functionalized with alcohols as stoichiometric reagents, yielding β-alkoxyalcohols. Among the solvents studied, best results were obtained in ethers in the presence of a strong proton acid as a catalyst. Alcohols include simple alkanols, diols, protected polyols, 3-butyn-1-ol 3-hydroxypropanenitrile and cholesterol. This protocol represents a convenient way for introduction of various functionalities onto epoxy-functionalized polymers. Under the reaction conditions, some side reactions take place, mostly due to the reactive ester group and water present in the reaction mixture.

  8. Dielectric properties study of surface engineered nanoTiO2/epoxy ...

    Indian Academy of Sciences (India)

    2018-02-02

    Feb 2, 2018 ... work, we employed linear, aromatic and extended aromatic organic groups containing organophosphate ligand molecules without any additional functional groups at the interface of. nanoTiO2 and epoxy resin. Figure 1 shows the chemical structures of organophosphate ligands that were examined as.

  9. Development of silane grafted ZnO core shell nanoparticles loaded diglycidyl epoxy nanocomposites film for antimicrobial applications.

    Science.gov (United States)

    Suresh, S; Saravanan, P; Jayamoorthy, K; Ananda Kumar, S; Karthikeyan, S

    2016-07-01

    In this article a series of epoxy nanocomposites film were developed using amine functionalized (ZnO-APTES) core shell nanoparticles as the dispersed phase and a commercially available epoxy resin as the matrix phase. The functional group of the samples was characterized using FT-IR spectra. The most prominent peaks of epoxy resin were found in bare epoxy and in all the functionalized ZnO dispersed epoxy nanocomposites (ZnO-APTES-DGEBA). The XRD analysis of all the samples exhibits considerable shift in 2θ, intensity and d-spacing values but the best and optimum concentration is found to be 3% ZnO-APTES core shell nanoparticles loaded epoxy nanocomposites supported by FT-IR results. From TGA measurements, 100wt% residue is obtained in bare ZnO nanoparticles whereas in ZnO core shell nanoparticles grafted DGEBA residue percentages are 37, 41, 45, 46 and 52% for 0, 1, 3, 5 and 7% ZnO-APTES-DGEBA respectively, which is confirmed with ICP-OES analysis. From antimicrobial activity test, it was notable that antimicrobial activity of 7% ZnO-APTES core shell nanoparticles loaded epoxy nanocomposite film has best inhibition zone effect against all pathogens under study. Copyright © 2016 Elsevier B.V. All rights reserved.

  10. Are concomitant patch test reactions to epoxy resin and BIS-GMA indicative of cross-reactivity?

    Science.gov (United States)

    Geier, Johannes; Lessmann, Holger; Uter, Wolfgang; Schnuch, Axel

    2007-12-01

    Despite rare simultaneous exposure, concomitant sensitisation to bisphenol A diglycidyl methacrylate (BIS-GMA) and epoxy resin frequently occurs. Immunological cross-reactivity has not been proven by animal experiments so far. Our objective was to examine cross-reactivity epidemiologically by analysing data of the Information Network of Departments of Dermatology (IVDK). From 2001 to 2005, 3,777 patients were patch tested with epoxy resin and BIS-GMA in the IVDK. We retrospectively analysed concomitant reactions to these allergens and to BIS-GMA and selected methacrylates. Additionally, we compared clinical characteristics of patients reacting to both, epoxy resin and BIS-GMA, with those of patients reacting to epoxy resin or BIS-GMA only. 185 patients reacted to epoxy resin, and 40 to BIS-GMA. Of the latter, 34 reacted to epoxy resin. There was no difference concerning exposure between the above-mentioned groups of patients. Concomitant reactions to BIS-GMA and methacrylates hardly ever occurred. Considering the fact that very few patients had been potentially exposed to BIS-GMA and that 85% of those reacting to BIS-GMA also reacted to epoxy resin, we conclude that our data are presumably indicative of immunological cross-reactivity. A verification of this hypothesis by animal experiments would be promising.

  11. Effect of cure cycle on enthalpy relaxation and post shrinkage in neat epoxy and epoxy composites

    DEFF Research Database (Denmark)

    Jensen, Martin; Jakobsen, Johnny

    2016-01-01

    The effect of cure cycle on enthalpy relaxation and warpage is studied for both neat epoxy and glass/epoxy composites. An approach for determining the enthalpy relaxation in the matrix of composite materials combining modulated differential scanning calorimetry and thermogravimetry is presented...

  12. Studies on the structural changes during curing of epoxy and its blend with CTBN

    Science.gov (United States)

    Srivastava, Kavita; Rathore, Ashwani Kumar; Srivastava, Deepak

    2018-01-01

    Cashew nut shell liquid (CNSL), an agricultural renewable resource material, produces natural phenolic distillates such as cardanol. Cardanol condenses with formaldehyde at the ortho- and para-position of the phenolic ring under acidic or alkaline condition to yield a series of polymers of novolac- or resol-type phenolic resins. These phenolic resins may further be modified by epoxidation with epichlorohydrin to duplicate the performance of such phenolic-type novolacs (CFN). The structural changes during curing of blend samples of epoxy and carboxyl terminated poly (butadiene-co-acrylonitrile) (CTBN) were studies by Fourier-transform infrared (FTIR) spectrophotometer. The epoxy samples were synthesized by biomass material, cardanol. Blend sample was prepared by physical mixing of CTBN ranging between 0 and 20 weight percent CTBN liquid rubber into cardanol-based epoxidized novolac (CEN) resin. The FTIR spectrum of uncured blend sample clearly indicated that there appeared a band in the region of 3200-3500 cm- 1 which might be due to the presence of phenolic hydroxyl group and sbnd OH group of the opened epoxide. Pure epoxy resin showed peaks near 856 cm- 1 which might be due to oxirane functionality of the epoxidized novolac resin. Both epoxy and its blend sample was cured with polyamine. The cure temperature of CEN resin was found to be decreased by the incorporation of CTBN. The decomposition behavior was also studied by thermogravimetric analyzer (TGA). Two-step decomposition behavior was observed in both epoxy and its blend samples.

  13. The solution curing performance of high-ortho epoxy phenolic fibers

    Science.gov (United States)

    Jiao, Mingli; Yang, Kai; Ren, Dongxue; Diao, Quan; Cao, Jian; Liu, Hongyan; Yu, Muhuo

    2017-07-01

    The high-ortho epoxy phenolic fibers (HEPFs) were prepared by the crosslinking of as-spun filaments derived from melt-spinning of the epoxy novolac resins copolymerized among epichlorohydrin (ECH), phenol and formaldehyde, and cured in a combined solution of formaldehyde and hydrochloric acid with a different heating rate. The changes in functional groups, thermal performance and mechanical properties during the different heating rates in solution curing were characterized. The results show that a peak of thermal stability and mechanical properties can be obtained with increasing heating rate, and crosslinking structure and characteristic group have changed after the solution curing. The epoxy phenolic fibers show great potential in the application of elastic flame-resistant textiles, aero-composites and precursors for activated carbon fibers used in electronic devices.

  14. Quantitative characterization of solid epoxy resins using comprehensive two dimensional liquid chromatography coupled with electrospray ionization-time of flight mass spectrometry.

    Science.gov (United States)

    Julka, Samir; Cortes, Hernan; Harfmann, Robert; Bell, Bruce; Schweizer-Theobaldt, Andreas; Pursch, Matthias; Mondello, Luigi; Maynard, Shawn; West, David

    2009-06-01

    A comprehensive multidimensional liquid chromatography system coupled to Electrospray Ionization-Mass Spectrometry (LCxLC-ESI-MS) was developed for detailed characterization and quantitation of solid epoxy resin components. The two orthogonal modes of separation selected were size exclusion chromatography (SEC) in the first dimension and liquid chromatography at critical conditions (LCCC) in the second dimension. Different components present in the solid epoxy resins were separated and quantitated for the first time based on the functional groups and molecular weight heterogeneity. Coupling LCxLC separations with mass spectrometry enabled the identification of components resolved in the two-dimensional space. Several different functional group families of compounds were separated and identified, including epoxy-epoxy and epoxy-alpha-glycol functional oligomers, and their individual molecular weight ranges were determined. Repeatability obtained ranged from 0.5% for the main product to 21% for oligomers at the 0.4% concentration level.

  15. Aliphatic amine cured PDMS–epoxy interpenetrating network ...

    Indian Academy of Sciences (India)

    Unknown

    formance electrical insulation, insulator housings, and encapsulation to withstand high voltage, moisture, oxidation, chemical attack, biological attack, outdoor weathering, contamination, electrical, mechanical and thermal stress. Keywords. PDMS; siloxane; epoxy; siliconized epoxy matrix; interpenetrating network. 1.

  16. Testing Tensile and Shear Epoxy Strength at Cryogenic Temperatures

    Science.gov (United States)

    Alberts, S. J.; Doehne, C. J.; Johnson, W. L.

    2017-01-01

    This paper covers cryogenic, tensile testing and research completed on a number of epoxies used in cryogenic applications. Epoxies are used in many different applications; however, this research focused on the use of epoxy used to bond MLI standoffs to cryogenic storage tanks and the loads imparted to the tank through the MLI. To conduct testing, samples were made from bare stainless steel, aluminum and primed aluminum. Testing involved slowly cooling test samples with liquid nitrogen then applying gradually increasing tensile loads to the epoxy. The testing evaluated the strength and durability of epoxies at cryogenic temperatures and serves as a base for future testing. The results of the tests showed that some epoxies withstood the harsh conditions while others failed. The two epoxies yielding the best results were Masterbond EP29LPSP and Scotch Weld 2216. For all metal surfaces tested, both epoxies had zero failures for up to 11.81 kg of mass.

  17. Fluorinated Alkyl Ether Epoxy Resin Compositions and Applications Thereof

    Science.gov (United States)

    Wohl, Christopher J. (Inventor); Connell, John W. (Inventor); Smith, Joseph G. (Inventor); Siochi, Emilie J. (Inventor); Gardner, John M. (Inventor); Palmieri, Frank M. (Inventor)

    2017-01-01

    Epoxy resin compositions prepared using amino terminated fluoro alkyl ethers. The epoxy resin compositions exhibit low surface adhesion properties making them useful as coatings, paints, moldings, adhesives, and fiber reinforced composites.

  18. How Do CNT affect the branch and crosslink reactions in CNT-epoxy

    Science.gov (United States)

    Cividanes, L. S.; Franceschi, W.; Ferreira, F. V.; Menezes, B. R. C.; Sales, R. C. M.; Thim, G. P.

    2017-10-01

    Carbon nanotube (CNT)-epoxy composites were prepared using carboxyl, amino and raw CNTs. The results of differential scanning calorimetry (DSC) showed that the effect of CNTs on the cure of epoxy resin is strongly dependent on the temperature and time. Raw and carboxyl CNTs accelerated the formation of branched chains (pre-cure at 80 °C), consuming the polymerization sites and leading to lower rates of crosslinking reaction (cure at 120 °C), resulting in lower storage modulus according to dynamic mechanical analysis (DMA). These results were explained by the catalysts of pre-cure (carboxylic groups and metallic residue of CNTs) and by CNT agglomerates, which could slow the crosslinking due to the consumption of epoxy sites. However, neat epoxy and amino-CNTs nanocomposites showed lower pre-cure rates and higher cure rates, resulting in higher storage modulus. Amino CNTs were the only nanotubes that increased the storage modulus of neat epoxy, due to the good homogeneity and adhesion of their composites.

  19. Facile fabrication of superhydrophobic films with fractal structures using epoxy resin microspheres

    Science.gov (United States)

    Quan, Yun-Yun; Zhang, Li-Zhi

    2014-02-01

    A simple method has been developed to fabricate superhydrophobic surfaces with fractal structures with epoxy resin microspheres (ERMs). The ERMs is produced by phase separation in an epoxy-amine curing system with a silica sol (SS) dispersant. The transparent epoxy solution becomes cloudy and turns into epoxy suspension (ES) in this process. The fractal structure (two tier structure) generated by synthetic epoxy resin microspheres (ERMs) and deposited nanoincrutations on the surfaces of these ERMs, which have been observed by scanning electron microscope (SEM). The curing time of ES is an important condition to obtain films with good comprehensive performances. Superhydrophobic films can be prepared by adding extra SS into ES with a curing time longer than 5 h. The optimal curing time is 10 h to fabricate a film with good mechanical stability and high superhydrophobicity. In addition, a surface with anti-wetting property of impacting microdroplets can be fabricated by prolonging the curing time of ES to 24 h. The gradually decreased hydrophilic groups resulted from a longer curing time enable the surface to have smaller surface adhesions to water droplets, which is the main reason to keep its superhydrophobicity under impacting conditions. The coated surface is highly hydrophobic and the impacting water droplets are bounced off from the surface.

  20. Impact of structure and functionality of core polyol in highly functional biobased epoxy resins.

    Science.gov (United States)

    Pan, Xiao; Webster, Dean C

    2011-09-01

    Highly functional biobased epoxy resins were prepared using dipentaerythritol (DPE), tripentaerythritol (TPE), and sucrose as core polyols that were substituted with epoxidized soybean oil fatty acids, and the impact of structure and functionality of the core polyol on the properties of the macromolecular resins and their epoxy-anhydride thermosets was explored. The chemical structures, functional groups, molecular weights, and compositions of epoxies were characterized using nuclear magnetic resonance (NMR) spectroscopy, Fourier-transform infrared (FTIR) spectroscopy, gel permeation chromatography (GPC), and matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI MS). The epoxies were also studied for their bulk viscosity, intrinsic viscosity, and density. Crosslinked with dodecenyl succinic anhydride (DDSA), epoxy-anhydride thermosets were evaluated using differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), tensile tests, and tests of coating properties. Epoxidized soybean oil (ESO) was used as a control. Overall, the sucrose-based thermosets exhibited the highest moduli, having the most rigid and ductile performance while maintaining the highest biobased content. DPE/TPE-based thermosets showed modestly better thermosetting performance than the control ESO thermoset. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  1. Non-isothermal cure and exfoliation of tri-functional epoxy-clay nanocomposites

    Directory of Open Access Journals (Sweden)

    F. Shiravand

    2015-08-01

    Full Text Available The non-isothermal cure kinetics of polymer silicate layered nanocomposites based on a tri-functional epoxy resin has been investigated by differential scanning calorimetry. From an analysis of the kinetics as a function of the clay content, it can be concluded that the non-isothermal cure reaction can be considered to consist of four different processes: the reaction of epoxy groups with the diamine curing agent; an intra-gallery homopolymerisation reaction which occurs concurrently with the epoxy-amine reaction; and two extra-gallery homopolymerisation reactions, catalysed by the onium ion of the organically modified clay and by the tertiary amines resulting from the epoxy-amine reaction. The final nanostructure displays a similar quality of exfoliation as that observed for the isothermal cure of the same nanocomposite system. This implies that the intra-gallery reaction, which is responsible for the exfoliation, is not significantly inhibited by the extra-gallery epoxy-amine cross-linking reaction.

  2. The Effect of High Concentration and Small Size of Nanodiamonds on the Strength of Interface and Fracture Properties in Epoxy Nanocomposite

    Directory of Open Access Journals (Sweden)

    Yasir A. Haleem

    2016-06-01

    Full Text Available The concentration and small size of nanodiamonds (NDs plays a crucial role in the mechanical performance of epoxy-based nanocomposites by modifying the interface strength. Herein, we systemically analyzed the relation between the high concentration and small size of ND and the fracture properties of its epoxy-based nanocomposites. It was observed that there is a two-fold increase in fracture toughness and a three-fold increase in fracture energy. Rationally, functionalized-NDs (F-NDs showed a much better performance for the nanocomposite than pristine NDs (P-NDs because of additional functional groups on its surface. The F-ND/epoxy nanocomposites exhibited rougher surface in contrast with the P-ND/epoxy, indicating the presence of a strong interface. We found that the interfaces in F-ND/epoxy nanocomposites at high concentrations of NDs overlap by making a web, which can efficiently hinder further crack propagation. In addition, the de-bonding in P-ND/epoxy nanocomposites occurred at the interface with the appearance of plastic voids or semi-naked particles, whereas the de-bonding for F-ND/epoxy nanocomposites happened within the epoxy molecular network instead of the interface. Because of the strong interface in F-ND/epoxy nanocomposites, at high concentrations the de-bonding within the epoxy molecular network may lead to subsequent cracks, parallel to the parent crack, via crack splitting which results in a fiber-like structure on the fracture surface. The plastic void growth, crack deflection and subsequent crack growth were correlated to higher values of fracture toughness and fracture energy in F-ND/epoxy nanocomposites.

  3. Composite materials based on modified epoxy resin and carbon fiber

    OpenAIRE

    Gonçalez, Viviane; Barcia, Fabio L.; Soares, Bluma G.

    2006-01-01

    Epoxy resin networks have been modified with block copolymer of polybutadiene and bisphenol A diglycidyl ether (DGEBA)-based on epoxy resin. The epoxy resin modified with carboxyl-terminated polybutadiene presented improved impact resistance and outstanding mechanical performance in terms of flexural and tensile properties because of the presence of rubber particles homogeneously dispersed inside the epoxy matrix. This modified system also resulted in an improvement of mechanical properties o...

  4. Aging in CTBN modified epoxy resin stocks

    International Nuclear Information System (INIS)

    Creed, K.E. Jr.

    1979-01-01

    The cause of degradation in the glass transition temperature (T/sub G/) of a partially crystallized polymer was investigated. Sample epoxy resin filled capacitors were cured at 90 0 C for 24 hours, then stored at room atmospheric conditions. These showed typical degradation in T/sub G/ after storage for one month. One set of epoxy resin castings was stored at room atmosphere and another set was stored in a dry box at 0% relative humidity and 27 0 C. The samples at room atmospheric conditions showed typical degradation in T/sub G/, while the T/sub G/ for those stored in the dry box increased. Further tests were then made on epoxy resin castings at various curing temperatures and times at both room atmosphere and 0% humidity. Resulting data indicated that absorption of moisture during storage was the predominant cause of T/sub G/ degradation, with stress relaxation another, though smaller, contributing factor

  5. Thermal Conductivity of Carbon Nanoreinforced Epoxy Composites

    Directory of Open Access Journals (Sweden)

    C. Kostagiannakopoulou

    2016-01-01

    Full Text Available The present study attempts to investigate the influence of multiwalled carbon nanotubes (MWCNTs and graphite nanoplatelets (GNPs on thermal conductivity (TC of nanoreinforced polymers and nanomodified carbon fiber epoxy composites (CFRPs. Loading levels from 1 to 3% wt. of MWCNTs and from 1 to 15% wt. of GNPs were used. The results indicate that TC of nanofilled epoxy composites increased with the increase of GNP content. Quantitatively, 176% and 48% increase of TC were achieved in nanoreinforced polymers and nanomodified CFRPs, respectively, with the addition of 15% wt. GNPs into the epoxy matrix. Finally, micromechanical models were applied in order to predict analytically the TC of polymers and CFRPs. Lewis-Nielsen model with optimized parameters provides results very close to the experimental ones in the case of polymers. As far as the composites are concerned, the Hashin and Clayton models proved to be sufficiently accurate for the prediction at lower filler contents.

  6. Spall Strength Measurements in Transparent Epoxy Polymers

    Science.gov (United States)

    Pepper, Jonathan; Rahmat, Meysam; Petel, Oren

    2017-06-01

    Polymer nanocomposites are seeing more frequent use in transparent armour applications. The role of the microstructure on the performance of these materials under dynamic tensile loading conditions is of particular interest. In the present study, a series of plate impact experiments was conducted in order to evaluate the dynamic response of an epoxy (EPON 828) cured with two differed hardeners. The purpose was to compare the role of these hardeners on the dynamic performance of the resulting transparent epoxy. The material response was resolved with a multi-channel photonic Doppler velocimeter. This system was used to determine the shock Hugoniot and dynamic tensile (spall) strength of the materials. The experimental results are presented in reference to spall theory and are evaluated against results predicted by an analytical model of the impacts. While varying the hardener did not change the shock Hugoniot of the epoxy, it did have an effect on the measured spall strengths.

  7. Single-component and fast-curing epoxy resin for liquid composite molding processes

    OpenAIRE

    Wang Yiru; Liu Wangshuang; Qiu Yiping; Wei Yi

    2017-01-01

    Development of single-component and fast-curing epoxy resins is highly desired for many industry applications. In this work, we report an epoxy system based on diglycidyl ether of bisphenol A (DGEBA) and 1-(2-cyanoethyl)-2-ethyl-4- methylimidazole (1C2E4MIM). The inductive effect of electron-withdrawing cyano group distinctly increases the latency of 1C2E4MIM without sacrificing the curing rate. The results of differential scanning calorimeter (DSC) and dynamic mechanical analysis (DMA) measu...

  8. Method of neutralizing the corrosive surface of amine-cured epoxy resins

    Science.gov (United States)

    Lee, S. Y. (Inventor)

    1982-01-01

    The corrosive alkaline surface layer of an epoxy resin product formed by the curing of the epoxy with an aliphatic amine is eliminated by first applying a non-solvent to remove most or all of the free unreacted amine and then applying a layer of a chemical reagent to neutralize the unused amine or amine functional groups by forming a substituted urea. The surface then may be rinsed with acetone and then with alcohol. The non-solvent may be an alcohol. The neutralizing chemical reagent is a mono-isocyanate or a mono-isothiocyanate. Preferred is an aromatic mono-isocyanate such as phenyl isocyanate, nitrophenyl isocyanate and naplthyl isocyanate.

  9. Effects of graphene oxides on the cure behaviors of a tetrafunctional epoxy resin

    Directory of Open Access Journals (Sweden)

    2011-09-01

    Full Text Available The influence of graphene oxides (GOs on the cure behavior and thermal stability of a tetrafunctional tetraglycidyl-4,4’-diaminodiphenylmethane cured with 4,4’-diaminodiphenylsulfone was investigated by using dynamic differential scanning calorimetry (DSC and thermogravimetric analysis (TGA. The dynamic DSC results showed that the initial reaction temperature and exothermal peak temperature decreased with the increase of GO contents. Furthermore, the addition of GO increased the enthalpy of epoxy cure reaction. Results from activation energy method showed that activation energies of GO/epoxy nanocomposites greatly decreased with the GO content in the latter stage, indicating that GOs significantly hindered the occurrence of vitrification. The oxygen functionalities, such as hydroxyl and carboxyl groups, on the surface of GOs acted as catalysts and facilitated the curing reaction and the catalytic effect increased with the GO contents. TGA results revealed that the addition of GOs decreased the thermal stability of epoxy.

  10. Adhesion between coating layers based on epoxy and silicone

    DEFF Research Database (Denmark)

    Svendsen, Jacob R.; Kontogeorgis, Georgios; Kiil, Søren

    2007-01-01

    The adhesion between a silicon tie-coat and epoxy primers, used in marine coating systems, has been studied in this work. Six epoxy coatings (with varying chain lengths of the epoxy resins), some of which have shown problems with adhesion to the tie-coat during service life, have been considered....

  11. Studies on blends of cycloaliphatic epoxy resin with varying ...

    Indian Academy of Sciences (India)

    Administrator

    mechanical analysis (DMA) of the blends of cycloaliphatic epoxy (CAE) resin toughened with liquid elastomer such as carboxyl ..... ber filled epoxy composites can behave as a better damp- ing material in dynamic applications compared to brittle epoxy resin. The cross linking density of the prepared blend systems showed ...

  12. Effect of Viscoelasticity on Adhesion of Bioinspired Micropatterned Epoxy Surfaces

    NARCIS (Netherlands)

    Castellanos, G.; Arzt, E.; Kamperman, M.M.G.

    2011-01-01

    The effect of viscoelasticity on adhesion was investigated for micropatterned epoxy surfaces and compared to nonpatterned surfaces. A two-component epoxy system was used to produce epoxy compositions with different viscoelastic properties. Pillar arrays with flat punch tip geometries were fabricated

  13. Aliphatic amine cured PDMS–epoxy interpenetrating network ...

    Indian Academy of Sciences (India)

    Unknown

    PDMS in the epoxy matrix increased the viscosity and lowered the exotherm and pot-life. PDMS in IPN increased ... stress. Keywords. PDMS; siloxane; epoxy; siliconized epoxy matrix; interpenetrating network. 1. Introduction. Any insulating material in service is exposed to moisture, oxidation, chemical attack, biological ...

  14. 40 CFR 721.3135 - Phosphorous modified epoxy resin (generic).

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Phosphorous modified epoxy resin... Specific Chemical Substances § 721.3135 Phosphorous modified epoxy resin (generic). (a) Chemical substance... phosphorous modified epoxy resin (PMNs P-00-992 and P-01-471) is subject to reporting under this section for...

  15. 40 CFR 721.2752 - Epoxy resin containing phosphorus (generic).

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Epoxy resin containing phosphorus... Specific Chemical Substances § 721.2752 Epoxy resin containing phosphorus (generic). (a) Chemical substance... epoxy resin containing phosphorus (PMN P-00-912) is subject to reporting under this section for the...

  16. 40 CFR 721.2755 - Cycloaliphatic epoxy resin (generic).

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Cycloaliphatic epoxy resin (generic... Substances § 721.2755 Cycloaliphatic epoxy resin (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as cycloaliphatic epoxy resin (PMN...

  17. Kevlar 49/Epoxy COPV Aging Evaluation

    Science.gov (United States)

    Sutter, James K.; Salem, Jonathan L.; Thesken, John C.; Russell, Richard W.; Littell, Justin; Ruggeri, Charles; Leifeste, Mark R.

    2008-01-01

    NASA initiated an effort to determine if the aging of Kevlar 49/Epoxy composite overwrapped pressure vessels (COPV) affected their performance. This study briefly reviews the history and certification of composite pressure vessels employed on NASA Orbiters. Tests to evaluate overwrap tensile strength changes compared 30 year old samples from Orbiter vessels to new Kevlar/Epoxy pressure vessel materials. Other tests include transverse compression and thermal analyses (glass transition and moduli). Results from these tests do not indicate a noticeable effect due to aging of the overwrap materials.

  18. Control of pore size in epoxy systems.

    Energy Technology Data Exchange (ETDEWEB)

    Sawyer, Patricia Sue; Lenhart, Joseph Ludlow (North Dakota State University, Fargo, ND); Lee, Elizabeth (North Dakota State University, Fargo, ND); Kallam, Alekhya (North Dakota State University, Fargo, ND); Majumdar, Partha (North Dakota State University, Fargo, ND); Dirk, Shawn M.; Gubbins, Nathan; Chisholm, Bret J. (North Dakota State University, Fargo, ND); Celina, Mathias C.; Bahr, James (North Dakota State University, Fargo, ND); Klein, Robert J.

    2009-01-01

    Both conventional and combinatorial approaches were used to study the pore formation process in epoxy based polymer systems. Sandia National Laboratories conducted the initial work and collaborated with North Dakota State University (NDSU) using a combinatorial research approach to produce a library of novel monomers and crosslinkers capable of forming porous polymers. The library was screened to determine the physical factors that control porosity, such as porogen loading, polymer-porogen interactions, and polymer crosslink density. We have identified the physical and chemical factors that control the average porosity, pore size, and pore size distribution within epoxy based systems.

  19. Immobilization of spent resin with epoxy resin

    International Nuclear Information System (INIS)

    Gultom, O.; Suryanto; Sayogo; Ramdan

    1997-01-01

    immobilization of spent resin using epoxy resin has been conducted. The spent resin was mixtured with epoxy resin in variation of concentration, i.e., 30, 40, 50, 60, 70 weight percent of spent resin. The mixture were pour into the plastic tube, with a diameter of 40 mm and height of 40 mm. The density, compressive strength and leaching rate were respectively measured by quanta chrome, paul weber apparatus and gamma spectrometer. The results showed that the increasing of waste concentration would be decreased the compressive strength, and increased density by immobilized waste. The leaching rate of 137 Cs from waste product was not detected in experiment (author)

  20. Healing of fatigue crack in epoxy materials with epoxy/mercaptan system via manual infiltration

    Directory of Open Access Journals (Sweden)

    2010-10-01

    Full Text Available The present work verified the capability of epoxy/mercaptan/tertiary amine system for retarding and/or arresting fatigue cracks in epoxy materials subjected to cyclic loading at room temperature. By using static and dynamic manual infiltration methods, the effects of hydrodynamic pressure crack tip shielding, polymeric wedge and adhesive bonding of the healing agent were revealed. Depending on the applied stress intensity range and the competition between polymerization kinetics of the healing agent and crack growth rate, the above mechanisms exerted different influences on crack retardation under different circumstances. On the whole, the epoxy/mercaptan/tertiary amine system proved to be very effective in obstructing fatigue crack propagation. It formed a promising base for developing self-healing epoxy materials that enable in-situ autonomic rehabilitation of fatigue crack.

  1. Characterization of Epoxy Functionalized Graphite Nanoparticles and the Physical Properties of Epoxy Matrix Nanocomposites

    Science.gov (United States)

    Miller, Sandi G.; Bauer, Jonathan L.; Maryanski, Michael J.; Heimann, Paula J.; Barlow, Jeremy P.; Gosau, Jan-Michael; Allred, Ronald E.

    2010-01-01

    This work presents a novel approach to the functionalization of graphite nanoparticles. The technique provides a mechanism for covalent bonding between the filler and matrix, with minimal disruption to the sp2 hybridization of the pristine graphene sheet. Functionalization proceeded by covalently bonding an epoxy monomer to the surface of expanded graphite, via a coupling agent, such that the epoxy concentration was measured as approximately 4 wt.%. The impact of dispersing this material into an epoxy resin was evaluated with respect to the mechanical properties and electrical conductivity of the graphite-epoxy nanocomposite. At a loading as low as 0.5 wt.%, the electrical conductivity was increased by five orders of magnitude relative to the base resin. The material yield strength was increased by 30% and Young s modulus by 50%. These results were realized without compromise to the resin toughness.

  2. Silanization of quartz, silicon and mica surfaces with light-driven molecular motors : construction of surface-bound photo-active nanolayers

    NARCIS (Netherlands)

    London, Gabor; Carroll, Gregory T.; Feringa, Ben L.

    2013-01-01

    The attachment of molecular rotary motors containing triethoxysilane functional groups to quartz, silicon and mica surfaces is described. Motors containing silane coupling agents in their structure form stable molecular layers on quartz and silicon surfaces. Motors attached to these surfaces were

  3. A novel hydroxyl epoxy phosphate monomer enhancing the anticorrosive performance of waterborne Graphene/Epoxy coatings

    Science.gov (United States)

    Ding, Jiheng; Rahman, Obaid ur; Peng, Wanjun; Dou, Huimin; Yu, Haibin

    2018-01-01

    Herein, we report the synthesis of a novel hydroxyl epoxy phosphate monomer (PGHEP) as an efficient dispersant for graphene to enhance the compatibility of the graphene in epoxy resin. Raman spectroscopy, Ultraviolet-visible spectroscopy (UV-vis) and X-ray photoelectron spectroscopy (XPS) studies were confirmed the π-π interactions between PGHEP and graphene. Well-dispersed states of PGHEP functionalized graphene (G) sheets in water were analyzed by transmission electron microscopy (TEM), atomic force microscopy (AFM) and scanning electron microscopy (SEM). Further, microstructure of prepared G/waterborne epoxy coatings containing 0.5-1.0 wt.% of PGHEP functionalized G sheets were also observed with the help of SEM and TEM. The PGHEP functionalized G sheets dispersed composite coatings displayed enhanced corrosion resistance compared with pure epoxy resin, these coatings have higher contact angle, lower water absorption as evident from the results of electrochemical impedance spectroscopy (EIS) and salt spray tests. The superior corrosion protection performances of G/epoxy coatings were mainly attributed to the formed passive film from uniformly dispersed PGHEP functionalized G sheets which act as physical barrier on the steel surface. Therefore, this work provides a novel bio-based efficient dispersant for G sheets and an important method for preparing G/waterborne epoxy coatings with superior corrosion resistance properties.

  4. Thermal expansion and swelling of cured epoxy resin used in graphite/epoxy composite materials

    Science.gov (United States)

    Adamson, M. J.

    1980-01-01

    The paper presents results of experiments in which the thermal expansion and swelling behavior of an epoxy resin system and two graphite/epoxy composite systems exposed to water were measured. It was found that the cured epoxy resin swells by an amount slightly less than the volume of the absorbed water and that the swelling efficiency of the water varies with the moisture content of the polymer. Additionally, the thermal expansion of cured epoxy resin that is saturated with water is observed to be more than twice that of dry resin. Results also indicate that cured resin that is saturated with 7.1% water at 95 C will rapidly increase in moisture content to 8.5% when placed in 1 C water. The mechanism for this phenomenon, termed reverse thermal effect, is described in terms of a slightly modified free-volume theory in conjunction with the theory of polar molecule interaction. Nearly identical behavior was observed in two graphite/epoxy composite systems, thus establishing that this behavior may be common to all cured epoxy resins.

  5. Effect of heat treatment on carbon fiber surface properties and fibers/epoxy interfacial adhesion

    International Nuclear Information System (INIS)

    Dai Zhishuang; Zhang Baoyan; Shi Fenghui; Li Min; Zhang Zuoguang; Gu Yizhuo

    2011-01-01

    Carbon fiber surface properties are likely to change during the molding process of carbon fiber reinforced matrix composite, and these changes could affect the infiltration and adhesion between carbon fiber and resin. T300B fiber was heat treated referring to the curing process of high-performance carbon fiber reinforced epoxy matrix composites. By means of X-ray photoelectron spectroscopy (XPS), activated carbon atoms can be detected, which are defined as the carbon atoms conjunction with oxygen and nitrogen. Surface chemistry analysis shows that the content of activated carbon atoms on treated carbon fiber surface, especially those connect with the hydroxyl decreases with the increasing heat treatment temperature. Inverse gas chromatography (IGC) analysis reveals that the dispersive surface energy γ S d increases and the polar surface energy γ S sp decreases as the heat treatment temperature increases to 200. Contact angle between carbon fiber and epoxy E51 resin, which is studied by dynamic contact angle test (DCAT) increases with the increasing heat treatment temperature, indicating the worse wettability comparing with the untreated fiber. Moreover, micro-droplet test shows that the interfacial shear strength (IFSS) of the treated carbon fiber/epoxy is lower than that of the untreated T300B fiber which is attributed to the decrement of the content of reactive functional groups including hydrogen group and epoxy group.

  6. Epoxy adhesive plays crucial role at CERN

    CERN Multimedia

    2007-01-01

    "Epoxy adhesives are set to play a vital role in Europe's biggest-ever scientific experiment at the European Centrefor Nuclear Research (CERN) in Geneva, Switzerland, thereby helping scientists gain a better understanding of the origins of the universe." (1/2 page)

  7. Epoxy adhesive plays crucial role at CERN

    CERN Multimedia

    2006-01-01

    "Epoxy adhesives are set to play a vital role in Europe's biggest-ever scientific experiment at the European Centre for Nuclear Research (CERN) in Geneva, Switzerland, thereby helping scientists gain a better understanding of the origins of the universe." (1 page)

  8. Influence of Ultraviolet/Ozonolysis Treatment of Nanocarbon Filler on the Electrical Resistivity of Epoxy Composites.

    Science.gov (United States)

    Perets, Yulia; Matzui, Lyudmila; Vovchenko, Lyudmila; Ovsiienko, Irina; Yakovenko, Olena; Lazarenko, Oleksandra; Zhuravkov, Alexander; Brusylovets, Oleksii

    2016-12-01

    In the present work, we have investigated concentration and temperature dependences of electrical conductivity of graphite nanoplatelets/epoxy resin composites. The content of nanocarbon filler is varied from 0.01 to 0.05 volume fraction. Before incorporation into the epoxy resin, the graphite nanoplatelets were subjected to ultraviolet ozone treatment at 20-min ultraviolet exposure. The electric resistance of the samples was measured by two- or four-probe method and teraohmmeter E6-13. Several characterization techniques were employed to identify the mechanisms behind the improvements in the electrical properties, including SEM and FTIR spectrum analysis.It is established that the changes of the relative intensities of the bands in FTIR spectra indicate the destruction of the carboxyl group -COOH and group -OH. Electrical conductivity of composites has percolation character and graphite nanoplatelets (ultraviolet ozone treatment for 20 min) addition which leads to a decrease of percolation threshold 0.005 volume fraction and increase values of electrical conductivity (by 2-3 orders of magnitude) above the percolation threshold in comparison with composite materials-graphite nanoplatelets/epoxy resin. The changes of the value and behavior of temperature dependences of the electrical resistivity of epoxy composites with ultraviolet/ozone-treated graphite nanoparticles have been analyzed within the model of effective electrical conductivity. The model takes into account the own electrical conductivity of the filler and the value of contact electric resistance between the filler particles of the formation of continuous conductive pathways.

  9. Contact allergy to epoxy resin: risk occupations and consequences.

    Science.gov (United States)

    Bangsgaard, Nannie; Thyssen, Jacob Pontoppidan; Menné, Torkil; Andersen, Klaus Ejner; Mortz, Charlotte G; Paulsen, Evy; Sommerlund, Mette; Veien, Niels Kren; Laurberg, Grete; Kaaber, Knud; Thormann, Jens; Andersen, Bo Lasthein; Danielsen, Anne; Avnstorp, Christian; Kristensen, Berit; Kristensen, Ove; Vissing, Susanne; Nielsen, Niels Henrik; Johansen, Jeanne Duus

    2012-08-01

    Epoxy resin monomers are strong skin sensitizers that are widely used in industrial sectors. In Denmark, the law stipulates that workers must undergo a course on safe handling of epoxy resins prior to occupational exposure, but the effectiveness of this initiative is largely unknown. To evaluate the prevalence of contact allergy to epoxy resin monomer (diglycidyl ether of bisphenol A; MW 340) among patients with suspected contact dermatitis and relate this to occupation and work-related consequences. The dataset comprised 20 808 consecutive dermatitis patients patch tested during 2005-2009. All patients with an epoxy resin-positive patch test were sent a questionnaire. A positive patch test reaction to epoxy resin was found in 275 patients (1.3%), with a higher proportion in men (1.9%) than in women (1.0%). The prevalence of sensitization to epoxy resin remained stable over the study period. Of the patients with an epoxy resin-positive patch test, 71% returned a questionnaire; 95 patients had worked with epoxy resin in the occupational setting, and, of these, one-third did not use protective gloves and only 50.5% (48) had participated in an educational programme. The 1% prevalence of epoxy resin contact allergy is equivalent to reports from other countries. The high occurrence of epoxy resin exposure at work, and the limited use of protective measures, indicate that reinforcement of the law is required. © 2012 John Wiley & Sons A/S.

  10. Corrosion Protection of Steel by Epoxy-Organoclay Nanocomposite Coatings

    Directory of Open Access Journals (Sweden)

    Domna Merachtsaki

    2017-06-01

    Full Text Available The purpose of the present work was to study the corrosion behavior of steel coated with epoxy-(organo clay nanocomposite films. The investigation was carried out using salt spray exposures, optical and scanning electron microscopy examination, open circuit potential, and electrochemical impedance measurements. The mechanical, thermomechanical, and barrier properties of pristine glassy epoxy polymer and epoxy-clay nanocomposites were examined. The degree of intercalation/exfoliation of clay nanoplatelets within the epoxy polymer also was determined. The mechanical, thermomechanical, and barrier properties of all the epoxy-clay nanocomposites were improved compared to those of the pristine epoxy polymer. In addition, both the pristine epoxy and the epoxy nanocomposite coatings protected the steel from corrosion. Furthermore, the protective properties of the nanocomposite coatings were superior compared to those of the pristine epoxy polymer. The protective properties of the nanocomposite coatings varied with the modified clay used. The epoxy-montmorillonite clay modified with primary octadecylammonium ions, Nanomer I.30E, had a better behavior than that modified with quaternary octadecylammonium ions, Nanomer I.28E.

  11. Industrially relevant epoxy-acrylate hybrid resin photopolymerizations

    Science.gov (United States)

    Ajiboye, Gbenga I.

    Photopolymerization of epoxy-acrylate hybrid resins takes advantages of inherent properties present in the free-radical and cationic reactions to reduce oxygen inhibition problems that plague free-radical reactions. Similarly, the combined reaction mechanisms reduce moisture sensitivity of the cationic reactions. Despite the advantages of epoxy-acrylate hybrid resins, problems persist that need to be addressed. For example, low conversion and polymerization rate of the epoxides are a problem, because the fast acrylate conversion prevents the epoxide from reaching high conversion. Controlling phase separation is challenging, since two moieties with different properties are reacting. The physical properties of the polymer will be impacted by the availability of different moieties. High shrinkage stress results from the acrylate moiety, causing buckling and cracking in film and coating applications. The overall goal of this study is to use the fundamental knowledge of epoxy-acrylate hybrid resins to formulate industrially viable polymers. In order to achieve this goal, the study focuses on the following objectives: (I) determine the apparent activation energy of the hybrid monomer METHB, (II) increase epoxide conversion and polymerization rate of hybrid formulations, and (III) control physical properties in epoxy-acrylate hybrid resins. In order to increase the epoxide conversion and rate of polymerization, the sensitivity of epoxides to alcohol is used to facilitate the activated monomer (AM) mechanism and induce a covalent bond between the epoxide and acrylate polymers through the hydroxyl group. It is hypothesized that if the AM mechanism is facilitated, epoxide conversion will increase. As a result, the resins can be tailored to control phase separation and physical properties, and shrinkage stress can be reduced. In pursuit of these objectives, the hybrid monomer METHB was polymerized at temperatures ranging from 30°C to 70°C to obtain apparent activation

  12. Assessment of cross-reactivity of new less sensitizing epoxy resin monomers in epoxy resin-allergic individuals.

    Science.gov (United States)

    Hagvall, Lina; Niklasson, Ida B; Rudbäck, Johanna; O'Boyle, Niamh M; Niklasson, Eva; Luthman, Kristina; Karlberg, Ann-Therese

    2016-09-01

    Measures to prevent occupational exposure to epoxy resins, including education, medical examination, and voluntary agreements between employers and workers, have not been effective enough to protect against skin sensitization. Therefore, alternatives to the major epoxy resin haptens that have been found to be less sensitizing in the local lymph node assay have been developed. To study the cross-reactivity of two newly designed epoxy resin monomers, with decreased skin-sensitizing potency and good technical properties as compared with diglycidyl ether of bisphenol A (DGEBA), in subjects with known contact allergy to epoxy resin of DGEBA type. Eleven individuals with previous positive patch test reactions to epoxy resin of DGEBA participated in the study. The two alternative epoxy resin monomers were synthesized and patch tested in dilution series in parallel with epoxy resin of DGEBA from the baseline series (containing 92% DGEBA). All participants reacted to epoxy resin of DGEBA on retesting. Three participants reacted to monomer 1. No reactions were seen to monomer 2. The alternative monomers studied showed little or no cross-reactivity with epoxy resin of DGEBA. Decreasing the risk of sensitization by using less sensitizing compounds is important, as contact allergy to epoxy resins is common in spite of thorough preventive measures. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  13. Self-Repairing Mechanism of MUF/Epoxy Microcapsules for Epoxy Material

    Science.gov (United States)

    Ni, Zhuo; Lin, Yuhao; Zhou, Xiaobo

    2017-12-01

    In this paper, a post curing reaction for the microcapsule/epoxy composite material and the conditions of thermal treatment for self-healing process were studied by differential scanning calorimetry (DSC). The condition of thermal treatment for post curing (60°C, 2 hours) was employed to fully cure the epoxy composite. Damage mechanism for the epoxy material was demonstrated via data simulation and three-point bending experiment for the stress distribution reveals that micro-cracks are more likely to be generated on the central region in stress concentration area of two constrained boundaries and the numbers of micro-cracks are reduced from the central area to the two ends of the material. Self-repairing performances of MUF microcapsule/epoxy composite materials were characterized using both destructive bending tests and non-destructive DMA measurements. Self-healing efficiencies of the composites embedded 2% and 5% microcapsule content measured by DMA are 101% and 104% respectively which are close to those results of 104% and 113% correspondingly measured by bending tests. Crack formation and development, core material releasing for MUF microcapsules and physiochemical process of the self-repairing were investigated by using OM, fluorescent technique and infrared microscope. These provide detailed evidences and important information on self-healing mechanism of the microcapsule/epoxy self-repairing material.

  14. Porous epoxy phenolic novolac resin polymer microcapsules: Tunable release and bioactivity controlled by epoxy value.

    Science.gov (United States)

    Zhang, Xian-Peng; Luo, Jian; Jing, Tong-Fang; Zhang, Da-Xia; Li, Bei-Xing; Liu, Feng

    2018-02-13

    Microcapsules (MCs) prepared with diverse wall material structures may exhibit different properties. In this study, MCs were fabricated with three kinds of epoxy phenolic novolac resins (EPNs), which possessed unique epoxy values as wall-forming materials by interfacial polymerization. The effects of the EPN types on the surface morphology, particle size distribution, encapsulation efficiency, thermal stability as well as release behavior and bioactivity of the MCs were investigated. In all three samples, the MCs had nearly spherical shapes with fine monodispersities and sizes in the range of 7-30 μm. Scanning electron microscopy (SEM) images showed that some small pores (ranging from 50 nm to 400 nm) appeared on the microcapsule surfaces and that the porosity decreased with an increasing of epoxy value. The X-ray diffractometer (XRD) analysis indicated that the cured EPN shells had larger degrees of crosslinking with higher epoxy values, leading to better thermal stabilities. Moreover, the release rate of the core material (pendimethalin) decreased with an increasing of epoxy value and thus resulted in a lower herbicidal control efficacy. The results of our research will enhance the potential application of EPNs as smart wall-forming materials to prepare porous MCs for controlled release. Copyright © 2018 Elsevier B.V. All rights reserved.

  15. Development of boron epoxy rocket motor chambers.

    Science.gov (United States)

    Jensen, W. M.; Knoell, A. C.; Zweben, C.

    1972-01-01

    A 71 cm diameter 74 cm length boron/epoxy composite rocket motor chamber was designed based on the geometric configuration of the JPL Applications Technology Satellite titanium alloy apogee motor chamber. Because analyses showed large stress concentrations in the domes, the configuration was modified using the same basic constraints for openings and attachments. The rocket motor chamber was then fabricated by filament winding with boron/epoxy tape and hydrostatically tested to failure at 264 N/sq cm, 57.2 N/sq cm above the design value. Two more rocket motor chambers were fabricated with the same basic constraints, but shortened to 57.6 cm for a smaller propellant load. The first of these short chambers failed in proof because of filament winding fabrication difficulties. The second chamber was successfully fabricated and passed the hydrostatic proof test.

  16. Investigations of toughening mechanisms of epoxy resins

    Science.gov (United States)

    Koenig, T.

    1986-01-01

    Composite material technology was applied to the solid rocket booster by the development of a carbon filament-epoxy resin case which yields a net increase of 4000 lbs. in payload in the shuttle. The question of reusability of the new composite tanks has not yet been answered and will depend on the toughness of the matrix resin. The present study was aimed at providing conditions whereby test specimens of the epoxy resin (EPON/85) and curing agents of systematically varied structures could be produced in a controlled manner. Three sets of conditions were found that might allow the isolation of the structural effects on toughness from the cure effects. The kinetic methods leading to the determination of these conditions are described.

  17. Some Aspects of Thermal Transport across the Interface between Graphene and Epoxy in Nanocomposites.

    Science.gov (United States)

    Wang, Yu; Yang, Chunhui; Pei, Qing-Xiang; Zhang, Yingyan

    2016-03-01

    Owing to the superior thermal properties of graphene, graphene-reinforced polymer nanocomposites hold great potential as the thermal interface materials (TIMs) dissipating heat for electronic packages. However, this application is greatly hindered by the high thermal resistance at the interface between graphene and polymer. In this paper, some important aspects of the improvement of the thermal transport across the interface between graphene and epoxy in graphene-epoxy nanocomposites, including the effectiveness of covalent and noncovalent functionalization, isotope doping, and acetylenic linkage in graphene are systematically investigated using molecular dynamics (MD) simulations. The simulation results show that the covalent and noncovalent functionalization techniques could considerably reduce the graphene-epoxy interfacial thermal resistance in the nanocomposites. Among different covalent functional groups, butyl is more effective than carboxyl and hydroxyl in reducing the interfacial thermal resistance. Different noncovalent functional molecules, including 1-pyrenebutyl, 1-pyrenebutyric acid, and 1-pyrenebutylamine, yield a similar amount of reductions. Moreover, it is found that the graphene-epoxy interfacial thermal resistance is insensitive to the carbon isotope doping in graphene, while it can be reduced moderately by replacing the sp(2) bonds in graphene with acetylenic linkages.

  18. Effect of sizing on carbon fiber surface properties and fibers/epoxy interfacial adhesion

    International Nuclear Information System (INIS)

    Dai Zhishuang; Shi Fenghui; Zhang Baoyan; Li Min; Zhang Zuoguang

    2011-01-01

    This paper aims to study effect of sizing on surface properties of carbon fiber and the fiber/epoxy interfacial adhesion by comparing sized and desized T300B and T700SC carbon fibers. By means of X-ray photoelectron spectroscopy (XPS), activated carbon atoms can be detected, which are defined as the carbon atoms conjunction with oxygen and nitrogen. Surface chemistry analysis shows that the desized carbon fibers present less concentration of activated carbon, especially those connect with the hydroxyl and epoxy groups. Inverse gas chromatography (IGC) analysis reveals that the desized carbon fibers have larger dispersive surface energy γ S D and smaller polar component γ S SP than the commercial sized ones. Moreover, micro-droplet test shows that the interfacial shear strength (IFSS) of the desized carbon fiber/epoxy is higher than those of the T300B and T700SC. Variations of the IFSS for both the sized and desized carbon fibers correspond to γ S D /γ S tendency of the fiber surface, however the work of adhesion does not reveal close correlation with IFSS trend for different fiber/epoxy systems.

  19. Optimization of interfacial properties of carbon fiber/epoxy composites via a modified polyacrylate emulsion sizing

    International Nuclear Information System (INIS)

    Yuan, Xiaomin; Zhu, Bo; Cai, Xun; Liu, Jianjun; Qiao, Kun; Yu, Junwei

    2017-01-01

    Highlights: • An improved interfacial adhesion in CF/EP composite by FSMPA sizing was put forward. • Sized CFs featured promotions of wettability, chemical activity and mechanical property. • A sizing mechanism containing chemical interaction and physical absorption was proposed. - Abstract: The adhesion behavior of epoxy resin to carbon fibers has always been a challenge, on account of the inertness of carbon fibers and the lack of reactive functional groups. In this work, a modified polyacrylate sizing agent was prepared to modify the interface between the carbon fiber and the epoxy matrix. The surface characteristics of carbon fibers were investigated to determine chemical composition, morphology, wettability, interfacial phase analysis and interfacial adhesion. Sized carbon fibers featured improved wettability and a slightly decreased surface roughness due to the coverage of a smooth sizing layer, compared with the unsized ones. Moreover, the content of surface activated carbon atoms increased from 12.65% to 24.70% and the interlaminar shear strength (ILSS) of carbon fiber/epoxy composites raised by 14.2%, indicating a significant improvement of chemical activity and mechanical property. SEM images of the fractured surface of composites further proved that a gradient interfacial structure with increased thicknesses was formed due to the transition role of the sizing. Based on these results, a sizing mechanism consisting of chemical interaction bonding and physical force absorption was proposed, which provides an efficient and feasible method to solve the poor adhesion between carbon fiber and epoxy matrix.

  20. A micro-Raman study of Cu-particulate-filled epoxy matrix composites

    Directory of Open Access Journals (Sweden)

    S. Tognana

    2014-05-01

    Full Text Available A micro-Raman study is carried out to investigate the influence of the filler on the curing process of bisphenol A diglycidyl ether (DGEBA-based epoxy matrix composites. The composites are cured (14 h at 393 K with an anhydride (methyl tetrahydro phthalic anhydride, MTHPA, 100:90 pbw, catalyzed with a tertiary amine (0.7 pbw and filled with a 30% volume of Cu particles of approximately 75 µm in diameter. The experimental results are compared with those obtained for the same epoxy resin unfilled and for the same composite with Cu filler but not catalyzed. The micro-Raman experimental technique is used to search for information on the curing process in different regions of the matrix, near to and far from the copper filler, taking into account the results of differential-scanning-calorimetry measurements performed on the same composites. The results provide information on the influence of the copper filler on the curing process of the epoxy matrix. Differences were observed in the peaks associated with the epoxy ring and the ester group as a function of the distance to the nearest copper particle, but no differences were observed between the different composites.

  1. Optimization of interfacial properties of carbon fiber/epoxy composites via a modified polyacrylate emulsion sizing

    Energy Technology Data Exchange (ETDEWEB)

    Yuan, Xiaomin [Key Laboratory for Liquid-Solid Structural Evolution and Processing of Materials (Ministry of Education), Shandong University, Jinan 250061 (China); Carbon Fiber Engineering Research Center, School of Materials Science and Engineering, Shandong University, Jinan 250061 (China); Zhu, Bo, E-mail: zhubo@sdu.edu.cn [Key Laboratory for Liquid-Solid Structural Evolution and Processing of Materials (Ministry of Education), Shandong University, Jinan 250061 (China); Carbon Fiber Engineering Research Center, School of Materials Science and Engineering, Shandong University, Jinan 250061 (China); Cai, Xun, E-mail: caixunzh@sdu.edu.cn [School of Computer Science and Technology, Shandong University, Jinan 250101 (China); Liu, Jianjun [Key Laboratory for Liquid-Solid Structural Evolution and Processing of Materials (Ministry of Education), Shandong University, Jinan 250061 (China); Carbon Fiber Engineering Research Center, School of Materials Science and Engineering, Shandong University, Jinan 250061 (China); Qiao, Kun [Carbon Fiber Engineering Research Center, School of Materials Science and Engineering, Shandong University, Jinan 250061 (China); Yu, Junwei [Key Laboratory for Liquid-Solid Structural Evolution and Processing of Materials (Ministry of Education), Shandong University, Jinan 250061 (China); Carbon Fiber Engineering Research Center, School of Materials Science and Engineering, Shandong University, Jinan 250061 (China)

    2017-04-15

    Highlights: • An improved interfacial adhesion in CF/EP composite by FSMPA sizing was put forward. • Sized CFs featured promotions of wettability, chemical activity and mechanical property. • A sizing mechanism containing chemical interaction and physical absorption was proposed. - Abstract: The adhesion behavior of epoxy resin to carbon fibers has always been a challenge, on account of the inertness of carbon fibers and the lack of reactive functional groups. In this work, a modified polyacrylate sizing agent was prepared to modify the interface between the carbon fiber and the epoxy matrix. The surface characteristics of carbon fibers were investigated to determine chemical composition, morphology, wettability, interfacial phase analysis and interfacial adhesion. Sized carbon fibers featured improved wettability and a slightly decreased surface roughness due to the coverage of a smooth sizing layer, compared with the unsized ones. Moreover, the content of surface activated carbon atoms increased from 12.65% to 24.70% and the interlaminar shear strength (ILSS) of carbon fiber/epoxy composites raised by 14.2%, indicating a significant improvement of chemical activity and mechanical property. SEM images of the fractured surface of composites further proved that a gradient interfacial structure with increased thicknesses was formed due to the transition role of the sizing. Based on these results, a sizing mechanism consisting of chemical interaction bonding and physical force absorption was proposed, which provides an efficient and feasible method to solve the poor adhesion between carbon fiber and epoxy matrix.

  2. Relationships between nanostructure and dynamic-mechanical properties of epoxy network containing PMMA-modified silsesquioxane

    Directory of Open Access Journals (Sweden)

    2009-06-01

    Full Text Available A new class of organic-inorganic hybrid nanocomposites was obtained by blending PMMA-modified silsesquioxane hybrid materials with epoxy matrix followed by curing with methyl tetrahydrophthalic anhydride. The hybrid materials were obtained by sol-gel method through the hydrolysis and polycondensation of the silicon species of the hybrid precursor, 3-methacryloxypropyltrimethoxysilane (MPTS, simultaneously to the polymerization of the methacrylate (MMA groups covalently bonded to the silicon atoms. The nanostructure of these materials was investigated by small angle X-ray scattering (SAXS and correlated to their dynamic mechanical properties. The SAXS results revealed a hierarchical nanostructure consisting on two structural levels. The first level is related to the siloxane nanoparticles spatially correlated in the epoxy matrix, forming larger hybrid secondary aggregates. The dispersion of siloxane nanoparticles in epoxy matrix was favored by increasing the MMA content in the hybrid material. The presence of small amount of hybrid material affected significantly the dynamic mechanical properties of the epoxy networks.

  3. Mechanical properties of epoxy composites with plasma-modified rice-husk-derived nanosilica

    Science.gov (United States)

    Hubilla, Fatima Athena D.; Panghulan, Glenson R.; Pechardo, Jason; Vasquez, Magdaleno R., Jr.

    2018-01-01

    In this study, we explored the use of rice-husk-derived nanosilica (nSiO2) as fillers in epoxy resins. The nSiO2 was irradiated with a capacitively coupled 13.56 MHz radio frequency (RF) plasma using an admixture of argon (Ar) and hexamethyldisiloxane (HMDSO) or 1,7-octadiene (OD) monomers. The plasma-polymerized nSiO2 was loaded at various concentrations (1–5%) into the epoxy matrix. Surface hydrophobicity of the plasma-treated nSiO2-filled composites increased, which is attributed to the attachment of functional groups from the monomer gases on the silica surface. Microhardness increased by at least 10% upon the inclusion of plasma-modified nSiO2 compared with pristine nSiO2–epoxy composites. Likewise, hardness increased with increasing loading volume, with the HMDSO-treated silica composite recording the highest increase. Elastic moduli of the composites also showed an increase of at least 14% compared with untreated nSiO2-filled composites. This work demonstrated the use of rice husk, an agricultural waste, as a nSiO2 source for epoxy resin fillers.

  4. Measurement of water diffusion in epoxy and polyester resins with radionuclides

    International Nuclear Information System (INIS)

    Mozisek, M.

    1976-01-01

    A brief characteristic is given of diffusion processes in polymers and their importance in the corrosion of plastics and synthetic resins. The method and equipment are described for the application of radionuclides in measuring the diffusion of water in epoxy and polyester resins. The desorption of water labelled with tritium and the diffusion coefficients of water molecules were investigated in five samples of resins. The experimental results show that there are evident differences between the individual evaluated synthetic resins in the diffusion rate of water molecules at temperatures within the region of 15 to 55 degC. Of the epoxy resins, the smallest diffusion rate of water was found for ChS Epoxifurol EFF hardened with the EFF 33 setting agent, and for ChS Epoxi 110 Bg 15. The ChS Epoxifurol EFF 33 type set by adding 20% aminoamide has a higher diffusion rate probably due to the presence of polar functional groups. The epoxy resin Eprosin E 26 containing a considerable amount of inorganic filler has a substantially higher diffusion rate for water molecules than the other types of evaluated resins. The polyester resin ChS Polyester 221 has the lowest rate of water diffusion. (J.B.)

  5. Properties of Two Carbon Composite Materials Using LTM25 Epoxy Resin

    Science.gov (United States)

    Cruz, Juan R.; Shah, C. H.; Postyn, A. S.

    1996-01-01

    In this report, the properties of two carbon-epoxy prepreg materials are presented. The epoxy resin used in these two materials can yield lower manufacturing costs due to its low initial cure temperature, and the capability of being cured using vacuum pressure only. The two materials selected for this study are MR50/LTM25, and CFS003/LTM25 with Amoco T300 fiber; both prepregs are manufactured by The Advanced Composites Group. MR50/LTM25 is a unidirectional prepreg tape using Mitsubishi MR50 carbon fiber impregnated with LTM25 epoxy resin. CRS003/LTM25 is a 2 by 2 twill fabric using Amoco T300 fiber and impregnated with LTM25 epoxy resin. Among the properties presented in this report are strength, stiffness, bolt bearing, and damage tolerance. Many of these properties were obtained at three environmental conditions: cold temperature/dry (CTD), room temperature/dry (RTD), and elevated temperature/wet (ETW). A few properties were obtained at room temperature/wet (RTW), and elevated temperature/dry (ETD). The cold and elevated temperatures used for testing were -125 F and 180 F, respectively. In addition, several properties related to processing are presented.

  6. Curing of natural rubber and epoxy adhesive

    International Nuclear Information System (INIS)

    Matawie, A.M.; Sadek, E.M.

    2001-01-01

    Low molecular weight epoxy resin based on diglycidyl ether of bisphenol A was synthesized and mixed at constant percentages with natural rubber. The rubber epoxy system was cured with various types of curing agents such as ethylene diamine, maleic anhydride as well as the prepared resole phenol formaldehyde. A study of the photo-induced crosslinking of the prepared elastic adhesives and film samples was carried out by exposure to ultraviolet lamp (300 w) for 2 weeks at 20 deg. C. Samples containing ethylene diamine were cured at 25 + - 1 deg. C. for 24 h while samples containing maleic anhydride or resole phenol formaldehyde resins were thermally cured at 150-170 deg. C. for 10 min. Cured adhesive compositions were tested mechanically and physically and evaluated as wood adhesives. While hardness, chemical resistance as well as heat stability of the prepared cured film sample were investigated. The obtained data indicate that the highest epoxy resin content and the presence of resole phenol formaldehyde resin in composition improve the tensile strength and adhesion properties on wood. While their cured film sample have the best hardness properties, chemical resistance and heat stability. (author)

  7. Ultrasonic and thermo-kinetic characterization of curing epoxy resin

    OpenAIRE

    Ali, Sheikh Mohammod

    2013-01-01

    This study combines cure kinetics modelling and thermal and ultrasonic cure monitoring to characterize the cure state of a complex commercial modified epoxy thermosetting system of industrial importance containing two epoxies, diethylene triamine hardener, external catalyst, aliphatic reactive diluent, and mica. Both catalyst and reactive diluent in the formulation of two epoxy resin mixture keep this complex system odd from others and to some extent a new one to report cure kinetics to the b...

  8. Prediction of brittle fracture of epoxy-aluminum flanging

    Directory of Open Access Journals (Sweden)

    Korbel J.

    2010-07-01

    Full Text Available This paper presents a fracture mechanical approach for estimation of critical bending load of different types of aluminum-epoxy flanging and comparison with experimental measurements. For this purpose, several designs of the flanges were investigated. The flanges were glued to the epoxy bars and adhesive-epoxy interface was considered as a bi-material notch. Prediction of the failure is based on generalized stress intensity factor and generalized fracture toughness.

  9. Thermal and microestructural characterization of epoxy-infiltrated hydroxyapatite composite

    OpenAIRE

    Roese,Pedro Barrionuevo; Amico,Sandro Campos; Kindlein Júnior,Wilson

    2009-01-01

    In this work, hydroxyapatite (HAp) obtained from the deorganification of bovine bones using hot NaOH solution was used to synthesize a HAp/epoxy infiltrated composite. Infiltration was carried out by vacuum assisted immersion in hot epoxy resin. The resulting composite was characterized regarding polymer content, morphological aspects and flexural strength. The infiltration method used resulted in thorough infiltration of the HAp but some residual porosity remained. Although the epoxy resin s...

  10. Reduction of polyester resin shrinkage by means of epoxy resin

    International Nuclear Information System (INIS)

    Pietrzak, M.; Brzostowski, A.

    1981-01-01

    An attempt was made to decrease the shrinkage of unsaturated polyester resin, taking place during radiation-induced curing, by the addition of epoxy resin. In order to combine chemically both resins, the epoxy component was modified with cinnamic and acrylic acids. A composition of 90 parts of polyester resin, 10 parts of epoxy resin modified with cinnamic acid, and 150 parts of a silica filler showed a volume shrinkage of 1.2%. (author)

  11. Gamma-irradiation on cured glycidyl amino-epoxy resin

    International Nuclear Information System (INIS)

    Yang, Ting; Wei, Chengsha; Liu, Hewen

    2010-01-01

    ITER is an international project to design and build an experimental fusion reactor based on the superconductive 'tokamak' concept. Amounts of epoxy resin are used in the superconductive tokamak device as impregnant resins, insulation breaks, etc. Resistance to ionizing radiation is a demanding performance of those epoxy resins. In this work, we study the effects of γ-irradiation on the mechanical properties and chemical structures of glycidyl amino-epoxy resins

  12. Pulse radiolysis studies on radiation resistance of epoxy resin

    International Nuclear Information System (INIS)

    Tagawa, S.; Washio, M.; Hayashi, N.; Tabata, Y.

    1985-01-01

    The mechanisms of radiation damage in epoxy resin, especially the primary processes, have been studied by a time-resolved spectroscopic technique (pulse radiolysis). The difference between the radiation resistance of aromatic and aliphatic amine curing epoxy resin is explained by internal radiation protection effects due to energy and charge transfer on the basis of the time-resolved spectroscopic data of reactive intermediate (excited states and ions) in an irradiated epoxy resin. (orig.)

  13. Positron lifetime study of electron-irradiated epoxy resins

    International Nuclear Information System (INIS)

    Suevegh, K.; Vertes, A.; Wojnarovits, L.; Foeldiak, G.; Liszkai, L.; Kajcsos, Zs.

    1990-01-01

    Two bisphenol-A type epoxy resins were irradiated by electron beam and studied afterwards by positron lifetime spectroscopy. An interesting result is that despite of the considerable amount of free-radicals, no inhibition of positronium formation was observed in the two epoxies. Nevertheless, several serious differences were detected between the studied polymers. The results suggest that the radiation-resistant properties of epoxies depend strongly on the amount of the curing agent. (author) 8 refs.; 2 figs

  14. Selective Clay Placement Within a Silicate-Clay Epoxy Blend Nanocomposite

    Science.gov (United States)

    Miller, Sandi G (Inventor)

    2013-01-01

    A clay-epoxy nanocomposite may be prepared by dispersing a layered clay in an alkoxy epoxy, such as a polypropylene oxide based epoxide before combining the mixture with an aromatic epoxy to improve the nanocomposite's thermal and mechanical properties.

  15. Photo-alignment of low-molecular mass nematic liquid crystals on photochemically bifunctional chalcone-epoxy film by irradiation of a linearly polarized UV light

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Dong Hoon; Cha, Young Kwan [Kyunghee Univ., Yongin (Korea, Republic of)

    2002-04-01

    Photocrosslinkable chalcone-epoxy compound comprising 1,3-bis-(4-hydroxy-phenyl)-propenone was synthesized for fabricating the photo-alignment layer of liquid crystals. Chalcone group was introduced into the main chain unit of the epoxy oligomer. We observed a photodimerization behavior and an optical anisotropy of this material by irradiation of a linearly polarized UV(LP-UV) light. With a trace amount of cationic photo initiator (TRS-HFA), polymerization of epoxy groups was also conducted at the similar wavelength range used for photodimerization . Linearly polarized UV irradiation on the chalcone-epoxy films with cationic photoinitiator induced optical anisotropy of the film and the resultant film can be used for alignment layers for low molecular weight nematic liquid crystals.

  16. Photo-alignment of low-molecular mass nematic liquid crystals on photochemically bifunctional chalcone-epoxy film by irradiation of a linearly polarized UV light

    CERN Document Server

    Choi, D H

    2002-01-01

    Photocrosslinkable chalcone-epoxy compound comprising 1,3-bis-(4-hydroxy-phenyl)-propenone was synthesized for fabricating the photo-alignment layer of liquid crystals. Chalcone group was introduced into the main chain unit of the epoxy oligomer. We observed a photodimerization behavior and an optical anisotropy of this material by irradiation of a linearly polarized UV(LP-UV) light. With a trace amount of cationic photo initiator (TRS-HFA), polymerization of epoxy groups was also conducted at the similar wavelength range used for photodimerization . Linearly polarized UV irradiation on the chalcone-epoxy films with cationic photoinitiator induced optical anisotropy of the film and the resultant film can be used for alignment layers for low molecular weight nematic liquid crystals.

  17. Understanding the thermal, mechanical and electrical properties of epoxy nanocomposites

    International Nuclear Information System (INIS)

    Sarathi, R.; Sahu, R.K.; Rajeshkumar, P.

    2007-01-01

    In the present work, the electrical, mechanical and thermal properties of epoxy nanocomposite materials were studied. The electrical insulation characteristics were analyzed through short time breakdown voltage test, accelerated electrical ageing test, and by tracking test. The breakdown voltage increases with increase in nano-clay content up to 5 wt%, under AC and DC voltages. The volume resistivity, permittivity and tan(δ) of the epoxy nanocomposites were measured. The Weibull studies indicate that addition of nanoclay upto 5 wt% enhances the characteristic life of epoxy nanocomposite insulation material. The tracking test results indicate that the tracking time is high with epoxy nanocomposites as compared to pure epoxy. Ageing studies were carried out to understand the surface characteristic variation through contact angle measurement. The hydrophobicity of the insulating material was analysed through contact angle measurement. The diffusion coefficients of the material with different percentage of clay in epoxy nanocomposites were calculated. The exfoliation characteristics in epoxy nanocomposites were analyzed through wide angle X-ray diffraction (WAXD) studies. The thermal behaviour of the epoxy nanocomposites was analyzed by carrying out thermo gravimetric-differential thermal analysis (TG-DTA) studies. Heat deflection temperature of the material was measured to understand the stability of the material for intermittent temperature variation. The dynamic mechanical analysis (DMA) results indicated that storage modulus of the material increases with small amount of clay in epoxy resin. The activation energy of the material was calculated from the DMA results

  18. Persistent photosensitivity after allergic contact dermatitis to epoxy resin.

    Science.gov (United States)

    Kwok, Tiffany; Rosen, Cheryl F; Storrs, Frances J; Lobel, Edmund; DeKoven, Joel G

    2013-01-01

    Persistent photosensitivity after allergic contact dermatitis (ACD) to epoxy resin has rarely been described. The aim of this study was to create awareness that ACD to epoxy may be a trigger for persistent photosensitivity. We present a series of 5 patients who developed ACD to epoxy resin and later a photodistributed eczematous eruption when exposed to sunlight, with a documented decrease in minimal erythema dose to UVA and UVB. The age of patients ranged from 34 to 71 years, and there were 3 men and 2 women. Each patient had occupational exposure to epoxy. Symptoms of epoxy ACD preceded photosensitivity by 5 months to 12 years in 3 cases and occurred simultaneously in 2 cases. Patch testing to epoxy resin was positive in all patients. Phototesting revealed a decreased minimal erythema dose to UVA and UVB in each of the 3 patients who were phototested. Photopatch testing was positive for epoxy resin in 1 of the 2 patients tested. All patients remained photosensitive for at least 2 years after diagnosis, with only 1 case of photosensitivity resolving with extended avoidance of epoxy. There is an association between ACD to epoxy resin and development of persistent photosensitivity. Possible mechanisms to explain the relationship between the 2 phenomena are discussed.

  19. Halloysite reinforced epoxy composites with improved mechanical properties

    Directory of Open Access Journals (Sweden)

    Saif Muhammad Jawwad

    2016-03-01

    Full Text Available Halloysite nanotubes (HNTs reinforced epoxy composites with improved mechanical properties were prepared. The prepared HNTs reinforced epoxy composites demonstrated improved mechanical properties especially the fracture toughness and flexural strength. The flexural modulus of nanocomposite with 6% mHNTs loading was 11.8% higher than that of neat epoxy resin. In addition, the nanocomposites showed improved dimensional stability. The prepared halloysite reinforced epoxy composites were characterized by thermal gravimetric analysis (TGA. The improved properties are attributed to the unique characteristics of HNTs, uniform dispersion of reinforcement and interfacial coupling.

  20. Surface treated fly ash filled modified epoxy composites

    Directory of Open Access Journals (Sweden)

    Uma Dharmalingam

    2015-01-01

    Full Text Available Abstract Fly ash, an inorganic alumino silicate has been used as filler in epoxy matrix, but it reduces the mechanical properties due to its poor dispersion and interfacial bonding with the epoxy matrix. To improve its interfacial bonding with epoxy matrix, surface treatment of fly ash was done using surfactant sodium lauryl sulfate and silane coupling agent glycidoxy propyl trimethoxy silane. An attempt is also made to reduce the particle size of fly ash using high pressure pulverizer. To improve fly ash dispersion in epoxy matrix, the epoxy was modified by mixing with amine containing liquid silicone rubber (ACS. The effect of surface treated fly ash with varying filler loadings from 10 to 40% weight on the mechanical, morphological and thermal properties of modified epoxy composites was investigated. The surface treated fly ash was characterized by particle size analyzer and FTIR spectra. Morphological studies of surface treated fly ash filled modified epoxy composites indicate good dispersion of fillers in the modified epoxy matrix and improves its mechanical properties. Impact strength of the surface treated fly ash filled modified epoxy composites show more improvement than unmodified composites.

  1. Design of carbon nanofiber embedded conducting epoxy resin

    International Nuclear Information System (INIS)

    Gantayat, Subhra; Sarkar, Niladri; Rout, Dibyaranjan; Swain, Sarat K.

    2017-01-01

    Acid treated carbon nanofiber (t-CNF) reinforced epoxy nanocomposites were fabricated by hand lay-up method with various wt % of t-CNF loadings. Pristine or unmodified carbon nano fibers (u-CNFs) were made compatible with epoxy matrix by means of mixed acid treatment. Fabricated nanocomposites were characterized with Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) study, scanning electron microscopy (SEM), transmission electron microscopy (TEM) and atomic force microscopy (AFM). Mechanical and thermal properties of the nanocomposites were measured as a function of t-CNF content. Effect of acid treated CNFs on to the mechanical properties of epoxy nanocomposites was justified by comparing the mechanical properties of epoxy/t-CNF and epoxy/u-CNF nanocomposites with same loading level. The electrical conductivity was achieved by epoxy resin with a threshold at 1 wt % of t-CNF. Substantial improvement in thermal, mechanical and electrical properties of the synthesized epoxy/t-CNF nanocomposites may be suitable for fabricating electronic devices. - Highlights: • Epoxy/t-CNF nanocomposites are characterized by XRD, FTIR, SEM, AFM and TEM. • Electrical conductivity was achieved by epoxy with a threshold at 1 wt% of t-CNF. • Tensile strength is enhanced by 40% due to dispersion of t-CNF. • Synthesized nanocomposites are suitable for fabricating electronic devises.

  2. Design of carbon nanofiber embedded conducting epoxy resin

    Energy Technology Data Exchange (ETDEWEB)

    Gantayat, Subhra [Department of Chemistry, Veer Surendra Sai University of Technology, Burla, Sambalpur 768018, Odisha (India); School of Applied Sciences, KIIT University, Bhubaneswar 751024, Odisha (India); Sarkar, Niladri [Department of Chemistry, Veer Surendra Sai University of Technology, Burla, Sambalpur 768018, Odisha (India); Rout, Dibyaranjan [School of Applied Sciences, KIIT University, Bhubaneswar 751024, Odisha (India); Swain, Sarat K., E-mail: swainsk2@yahoo.co.in [Department of Chemistry, Veer Surendra Sai University of Technology, Burla, Sambalpur 768018, Odisha (India)

    2017-01-15

    Acid treated carbon nanofiber (t-CNF) reinforced epoxy nanocomposites were fabricated by hand lay-up method with various wt % of t-CNF loadings. Pristine or unmodified carbon nano fibers (u-CNFs) were made compatible with epoxy matrix by means of mixed acid treatment. Fabricated nanocomposites were characterized with Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) study, scanning electron microscopy (SEM), transmission electron microscopy (TEM) and atomic force microscopy (AFM). Mechanical and thermal properties of the nanocomposites were measured as a function of t-CNF content. Effect of acid treated CNFs on to the mechanical properties of epoxy nanocomposites was justified by comparing the mechanical properties of epoxy/t-CNF and epoxy/u-CNF nanocomposites with same loading level. The electrical conductivity was achieved by epoxy resin with a threshold at 1 wt % of t-CNF. Substantial improvement in thermal, mechanical and electrical properties of the synthesized epoxy/t-CNF nanocomposites may be suitable for fabricating electronic devices. - Highlights: • Epoxy/t-CNF nanocomposites are characterized by XRD, FTIR, SEM, AFM and TEM. • Electrical conductivity was achieved by epoxy with a threshold at 1 wt% of t-CNF. • Tensile strength is enhanced by 40% due to dispersion of t-CNF. • Synthesized nanocomposites are suitable for fabricating electronic devises.

  3. Cobalt Ions Improve the Strength of Epoxy Resins

    Science.gov (United States)

    Stoakley, D. M.; St. Clair, A. K.

    1986-01-01

    Technique developed for improving mechanical strength of epoxy resins by adding cobalt ions in form of tris(acetylacetonato)cobalt (III) complex. Solid cast disks prepared from cobalt ion-containing epoxy resins tested for flexural strength and stiffness. Incorporation of cobalt ions into epoxies increased flexural strength of resins by 10 to 95 percent. Suitable resins for this technique include any liquid or solid TGMDA resins. Improved epoxy formulation proves useful as composite matrix resin, adhesive, or casting resin for applications on commercial and advanced aircraft.

  4. Toughened epoxy resin system and a method thereof

    Science.gov (United States)

    Janke, Christopher J.; Dorsey, George F.; Havens, Stephen J.; Lopata, Vincent J.

    1998-01-01

    Mixtures of epoxy resins with cationic initiators are curable under high energy ionizing radiation such as electron beam radiation, X-ray radiation, and gamma radiation. The composition of this process consists of an epoxy resin, a cationic initiator such as a diaryliodonium or triarylsulfonium salt of specific anions, and a toughening agent such as a thermoplastic, hydroxy-containing thermoplastic oligomer, epoxy-containing thermoplastic oligomer, reactive flexibilizer, rubber, elastomer, or mixture thereof. Cured compositions have high glass transition temperatures, good mechanical properties, and good toughness. These properties are comparable to those of similar thermally cured epoxies.

  5. Effect of the hardener to epoxy monomer ratio on the water absorption behavior of the DGEBA/TETA epoxy system

    Directory of Open Access Journals (Sweden)

    Ayrton Alef Castanheira Pereira

    2016-02-01

    Full Text Available Abstract The water absorption behavior of the DGEBA/TETA epoxy system was evaluated as a function of the epoxy monomer to amine hardener ratio. Weight gain versus immersion time curves were obtained and the experimental points were fitted using Fickian and Non-Fickian diffusion models. The results obtained showed that for all epoxy monomer to hardener ratios analyzed water diffusion followed non-Fickian behavior. It was possible to correlate the water absorption behavior to the macromolecular structure developed when the epoxy/ hardener ratio was varied. All epoxy/hardener ratios present a two-phase macromolecular structure, composed of regions with high crosslink density and regions with lower crosslinking. Epoxy rich systems have a more open macromolecular structure with a lower fraction of the dense phase than the amine rich systems, which present a more compact two-phase structure.

  6. Preparation and Characterization of Epoxy Resin Cross-Linked with High Wood Pyrolysis Bio-Oil Substitution by Acetone Pretreatment

    Directory of Open Access Journals (Sweden)

    Yi Liu

    2017-03-01

    Full Text Available The use of cost effective solvents may be necessary to store wood pyrolysis bio-oil in order to stabilize and control its viscosity, but this part of the production system has not been explored. Conversely, any rise in viscosity during storage, that would occur without a solvent, will add variance to the production system and render it cost ineffective. The purpose of this study was to modify bio-oil with a common solvent and then react the bio-oil with an epoxy for bonding of wood without any loss in properties. The acetone pretreatment of the bio-oil/epoxy mixture was found to improve the cross-linking potential and substitution rate based on its mechanical, chemical, and thermal properties. Specifically, the bio-oil was blended with epoxy resin at weight ratios ranging from 2:1 to 1:5 and were then cured. A higher bio-oil substitution rate was found to lower the shear bond strength of the bio-oil/epoxy resins. However, when an acetone pretreatment was used, it was possible to replace the bio-oil by as much as 50% while satisfying usage requirements. Extraction of the bio-oil/epoxy mixture with four different solvents demonstrated an improvement in cross-linking after acetone pretreatment. ATR-FTIR analysis confirmed that the polymer achieved a higher cross-linked structure. DSC and TGA curves showed improved thermal stability with the addition of the acetone pretreatment. UV-Vis characterization showed that some functional groups of the bio-oil to epoxy system were unreacted. Finally, when the resin mixture was utilized to bond wood, the acetone pretreatment coupled with precise tuning of the bio-oil:epoxy ratio was an effective method to control cross-linking while ensuring acceptable bond strength.

  7. Thermo-mechanical characterization of siliconized E-glass fiber/hematite particles reinforced epoxy resin hybrid composite

    Energy Technology Data Exchange (ETDEWEB)

    Arun Prakash, V.R., E-mail: vinprakash101@gmail.com; Rajadurai, A., E-mail: rajadurai@annauniv.edu.in

    2016-10-30

    Highlights: • Particles dimension have reduced using Ball milling process. • Importance of surface modification was explored. • Surface modification has been done to improve adhesion of fiber/particles with epoxy. • Mechanical properties has been increased by adding modified fiber and particles. • Thermal properties have been increased. - Abstract: In this present work hybrid polymer (epoxy) matrix composite has been strengthened with surface modified E-glass fiber and iron(III) oxide particles with varying size. The particle sizes of 200 nm and <100 nm has been prepared by high energy ball milling and sol-gel methods respectively. To enhance better dispersion of particles and improve adhesion of fibers and fillers with epoxy matrix surface modification process has been done on both fiber and filler by an amino functional silane 3-Aminopropyltrimethoxysilane (APTMS). Crystalline and functional groups of siliconized iron(III) oxide particles were characterized by XRD and FTIR spectroscopy analysis. Fixed quantity of surface treated 15 vol% E-glass fiber was laid along with 0.5 and 1.0 vol% of iron(III) oxide particles into the matrix to fabricate hybrid composites. The composites were cured by an aliphatic hardener Triethylenetetramine (TETA). Effectiveness of surface modified particles and fibers addition into the resin matrix were revealed by mechanical testing like tensile testing, flexural testing, impact testing, inter laminar shear strength and hardness. Thermal behavior of composites was evaluated by TGA, DSC and thermal conductivity (Lee’s disc). The scanning electron microscopy was employed to found shape and size of iron(III) oxide particles adhesion quality of fiber with epoxy matrix. Good dispersion of fillers in matrix was achieved with surface modifier APTMS. Tensile, flexural, impact and inter laminar shear strength of composites was improved by reinforcing surface modified fiber and filler. Thermal stability of epoxy resin was improved

  8. Epoxy composites coating with Fe3O4 decorated graphene oxide: Modified bio-inspired surface chemistry, synergistic effect and improved anti-corrosion performance

    Science.gov (United States)

    Zhan, Yingqing; Zhang, Jieming; Wan, Xinyi; Long, Zhihang; He, Shuangjiang; He, Yi

    2018-04-01

    To obtain graphene or graphene derivatives based epoxy composite coatings with high anti-corrosion performance, the morphology of nanostructures, dispersion, and interfacial adhesion are key factors that need to be considered. We here demonstrated the bio-inspired co-modification of graphene oxide/Fe3O4 hybrid (GO-Fe3O4@ poly (DA+KH550)) and its synergistic effect on the anti-corrosion performance of epoxy coating. For this purpose, graphene oxide/Fe3O4 hybrid obtained from hydrothermal route was modified by self-polymerization between dopamine and secondary functional monomer (KH550), which led to the modified bio-inspired surface functionalization. This novel modified bio-inspired functionalization was quite distinct from conventional surface modification or decoration. Namely, abundant amino groups were introduced by modified bio-inspired functionalization, which allowed the graphene oxide/Fe3O4 hybrid to disperse well in epoxy resin and enhanced the interfacial adhesion between modified nanofiller and epoxy resin through chemical crosslinking reaction. The electrochemical impedance spectroscopy (EIS) test revealed that anti-corrosive performance of epoxy coatings was significantly enhanced by addition of 0.5 wt% modified bio-inspired functionalized GO-Fe3O4 hybrid compared with neat epoxy and other nanofillers/epoxy composite coatings. Moreover, the micro-hardness of epoxy coating was enhanced by 71.8% compared with pure epoxy coating at the same loading content. In addition, the anticorrosion mechanism of GO-Fe3O4@poly (DA+KH550) was tentatively discussed.

  9. Glass Reinforcement of Various Epoxy Resins-Polyurea Systems

    Science.gov (United States)

    Joshi, Medha; Jauhari, Smita

    2012-07-01

    Polyureas (PUs) were prepared by the polycondensation reaction of disperse dyes containing -NH2 group and toluene 2, 4-diisocyanate. The disperse dyes have been prepared by coupling of various 2-diazobenzothiazoles with 1,3-benzenediamine. All the PUs were characterized by elemental analysis, spectral studies, number average molecular weight ( {overline{{Mn}} } ), and thermogravimetry. Further reaction of PUs was carried out with an epoxy resin (i.e., DGEBA). The curing study of prepared resins was monitored by differential scanning calorimeter (DSC). Based on DSC, thermograms glass fiber-reinforced composites have been laminated and characterized by chemical, mechanical, and electrical properties. The unreinforced cured resins were subjected to thermogravimetric analysis (TGA). The laminated composites showed excellent resistance properties against chemicals and good mechanical and electrical properties.

  10. Epoxy Corrosion-Resistant Coating

    Science.gov (United States)

    1991-10-22

    diethylene glycol monoethyl ether acetate, etc. The coating was found to have outstanding perfor- mance when exposed to extreme heat conditions, high...ketone, methyl isobutyl ketone, diethyl ketone, and cyclohexa- none. Glycoi ester solvents include ethylene glycol monoethyl ether acetate...applied conttm» glycidyl ether groups. The preferred polyglyc- on a variety of substrates. **’ comP°unds" denved by the condensation reac- tions of

  11. Preparation, Characterization, Thermal, and Flame-Retardant Properties of Green Silicon-Containing Epoxy/Functionalized Graphene Nanosheets Composites

    Directory of Open Access Journals (Sweden)

    Ming-Yuan Shen

    2013-01-01

    Full Text Available In this investigation, silane was grafted onto the surface of graphene nanosheets (GNSs through free radical reactions, to form Si-O-Et functional groups that can undergo the sol-gel reaction. To improve the compatibility between the polymer matrix and the fillers, epoxy monomer was modified using a silane coupling agent; then, the functionalized GNSs were added to the modified epoxy to improve the thermal stability and strengthen the flame-retardant character of the composites. High-resolution X-ray photoelectron spectrometry reveals that when the double bonds in VTES are grafted to the surfaces of GNSs. Solid-state 29Si nuclear magnetic resonance presents that the distribution of the signal associated with the T3 structure is wide and significant, indicating that the functionalization reaction of the silicone in the modified epoxy and VTES-GNSs increases the network-like character of the structures. Thermal gravimetric analysis, the integral procedure decomposition temperature, and limiting oxygen index demonstrate that the GNSs composites that contained silicon had a higher thermal stability and stronger flame-retardant character than pure epoxy. The dynamic storage modulus of all of the m-GNSs containing composites was significantly higher than that of the control epoxy, and the modulus of the composites increased with the concentration of m-GNSs.

  12. Multidimensional Nanocomposites of Epoxy Reinforced with 1D and 2D Carbon Nanostructures for Improve Fracture Resistance

    Directory of Open Access Journals (Sweden)

    Juventino López-Barroso

    2018-03-01

    Full Text Available A hybrid nanocomposites based on epoxy reinforced with a combination of 1D and 2D carbon nanomaterials for improving impact resistance are reported. Multi-walled carbon nanotubes and oxidized-multi-walled carbon nanotubes are used as 1D nanoreinforcements, and graphene derivative materials such as graphene oxide and reduced graphene oxide are utilized as 2D nanoreinforcements. In this research, the impact resistance of epoxy matrix reinforced with 1D or 2D and the mixture of both nanomaterials is studied. The research is focused on evaluation of the influence of adding different combinations of nanomaterials into epoxy resin and their Izod impact response. Moreover, fracture surface of nanocomposites is observed by scanning electron microscopy. Images show differences between the surfaces of brittle nature on thermoset epoxy polymer and tough nanocomposites. Synergy created with 1D and 2D nanomaterials produces stable dispersions in the processing, reflected in the interface. The interactions in nanocomposites are evidenced by infrared spectra, principally on the peaks related to oxygenated functional groups present in nanomaterials and absent in polymer matrix. Consequently, an increase of 138% in fracture strength of nanocomposites is exhibited, in comparison to the neat epoxy matrix. In addition, hybrid nanocomposites were synthesized in two different methods to evaluate the influence of manufacturing method on final properties of nanocomposites.

  13. Studies on the physico-mechanical and thermal characteristics of blends of DGEBA epoxy, 3,4 epoxy cyclohexylmethyl, 3',4'-epoxycylohexane carboxylate and carboxyl terminated butadiene co-acrylonitrile (CTBN)

    Energy Technology Data Exchange (ETDEWEB)

    Tripathi, Garima [Department of Plastic Technology, H. B. Technological Institute, Kanpur 208002 (India); Srivastava, Deepak [Department of Plastic Technology, H. B. Technological Institute, Kanpur 208002 (India)], E-mail: deepak_sri92@rediffmail.com

    2008-11-25

    Toughening of blend of diglycidyl ether of bisphenol-A (DGEBA) and 3,4 epoxy cyclohexylmethyl, 3',4'-epoxycylohexane carboxylate, i.e. cycloaliphatic epoxy resin (CAE) with varying weight ratios (0-25 wt%) of carboxyl terminated butadiene acrylonitrile (CTBN) copolymer have been investigated. Fourier transform infrared (FTIR) spectroscopic analysis established that the interaction between oxirane groups of DGEBA, CAE and CTBN were responsible for characteristics peak shifts in the blends compared to their counterparts. Physico-mechanical properties of the prepared samples, e.g. tensile, flexural and impact strengths showed an optimum concentration of CTBN (15 wt%) into epoxy matrix, which offered maximum toughening. Thermal stability of the prepared samples was analyzed by dynamic thermogravimetric runs. Cross-sections of the cured samples which failed during impact testing have been critically studied through scanning electron microscopic (SEM) analysis to gain insight into the phase morphology.

  14. Thermal Expansion and Swelling of Cured Epoxy Resin Used in Graphite/Epoxy Composite

    Science.gov (United States)

    Adamson, M. J.

    1979-01-01

    The thermal expansion and swelling of resin material as influenced by variations in temperature during moisture absorption is discussed. Comparison measurements using composites constructed of graphite fibers and each of two epoxy resin matrices are included. Polymer theory relative to these findings is discussed and modifications are proposed.

  15. Environmental Degradation and Durability of Epoxy-Clay Nanocomposites

    Directory of Open Access Journals (Sweden)

    Raman P. Singh

    2010-01-01

    Full Text Available This experimental investigation reports on the durability of epoxy-clay nanocomposites upon exposure to multiple environments. Nanocomposites are fabricated by mixing the clay particles using various combinations of mechanical mixing, high-shear dispersion, and ultrasonication. Clay morphology is characterized using X-ray diffraction and transmission electron microscopy. Specimens of both neat epoxy and the epoxy-clay nanocomposite are subjected to two environmental conditions: combined UV radiation and condensation on 3-hour repeat cycle and constant temperature-humidity, for a total exposure duration of 4770 hours. The presence of nanoscale clay inhibits moisture uptake, as demonstrated by exposure to constant temperature-humidity. Nonetheless, both materials lose mass under exposure to combined UV radiation and condensation due to the erosion of epoxy by a synergistic process. Surprisingly, the epoxy-clay specimens exhibit greater mass loss, as compared to neat epoxy. Mechanical testing shows that either environment does not significant affect the flexure modulus of either material. On the other hand, both materials undergo degradation in flexural strength when exposed to either environment. However, the epoxy-clay nanocomposite retains 37% more flexure strength than the neat epoxy after 4072 hours of exposure.

  16. Aliphatic amine cured PDMS–epoxy interpenetrating network ...

    Indian Academy of Sciences (India)

    The siliconized epoxy IPN, with better impact and thermal resistance, may be used in automobile and aerospace applications to withstand high temperature, and mechanical stress. The PDMS–epoxy IPN may be used for encapsulation, high temperature and high voltage application due to their low shrinkage and lesser ...

  17. Effect of alcoholic treated MWCNT on tensile behavior of epoxy ...

    African Journals Online (AJOL)

    Tensile strength, Young's modulus, and Elongation are found to be effectively improved with the addition of alcoholic functionalized MWCNT in epoxy matrix. Increased tensile strength and elastic modulus of epoxy composites loaded with the alcoholic functionalized MWCNT are observed through experimental studies.

  18. Flexural Properties of Activated Carbon Filled Epoxy Nano composites

    International Nuclear Information System (INIS)

    Khalil, H.P.S.A.; Khalil, H.P.S.A.; Alothman, O.Y.; Paridah, M.T.; Zainudin, E.S.

    2014-01-01

    Activated carbon (AC) filled epoxy nano composites obtained by mixing the desired amount of nano AC viz., bamboo stem, oil palm empty fruit bunch, and coconut shell from agricultural biomass with the epoxy resin. Flexural properties of activated carbons filled epoxy nano composites with 1 %, and 5 % filler loading were measured. In terms of flexural strength and modulus, a significant increment was observed with addition of 1 % vol and 5 % vol nano-activated carbon as compared to neat epoxy. The effect of activated carbon treated by two chemical agents (potassium hydroxide and phosphoric acid) on the flexural properties of epoxy nano composites were also investigated. Flexural strength of activated carbon-bamboo stem, activated carbon-oil palm, and activated carbon-coconut shell reinforced epoxy nano composites showed almost same value in case of 5 % potassium hydroxide activated carbon. Flexural strength of potassium hydroxide activated carbon-based epoxy nano composites was higher than phosphoric acid activated carbon. The flexural toughness of both the potassium hydroxide and phosphoric acid activated carbon reinforced composites range between 0.79 - 0.92 J. It attributed that developed activated carbon filled epoxy nano composites can be used in different applications. (author)

  19. Realtime 3D stress measurement in curing epoxy packaging

    DEFF Research Database (Denmark)

    Richter, Jacob; Hyldgård, A.; Birkelund, Karen

    2007-01-01

    This paper presents a novel method to characterize stress in microsystem packaging. A circular p-type piezoresistor is implemented on a (001) silicon chip. We use the circular stress sensor to determine the packaging induced stress in a polystyrene tube filled with epoxy. The epoxy curing process...

  20. A room temperature cured low dielectric hyperbranched epoxy ...

    Indian Academy of Sciences (India)

    Hyperbranched epoxy; poly(amido-amine) dendrimer; curing agent; low dielectric constant; high performance. 1. Introduction. Epoxy resins have a broad range of applications includ- ing binder for coatings, high performance composites, adhesives, insulating materials, encapsulating and pack- aging materials for electronic ...

  1. Chemical changes and tensile and electrical properties of epoxy ...

    African Journals Online (AJOL)

    The properties of epoxy rsesin can be improved by the use of nanofiller such as carbon black (CB), The nanocomposite was synthesized by dispersion via sonication and shear mixing. The morphology, surface chemistry and the structure of CB and the epoxy/CB nanocomposites were investigated using XPS, FTIR, FESEM, ...

  2. Studies on blends of cycloaliphatic epoxy resin with varying ...

    Indian Academy of Sciences (India)

    Administrator

    rials, it is proposed to blend cycloaliphatic epoxy resin with carboxyl terminated butadiene acrylonitrile copolymer. (CTBN). In the previous years, studies on the modifica- tion of diglycidyl ether of bisphenol-A based (DGEBA) epoxies with various reactive liquid rubbers were found abundantly in the literature (Visconti and ...

  3. A room temperature cured low dielectric hyperbranched epoxy ...

    Indian Academy of Sciences (India)

    Tomalia et al.5 Though curing kinetics of bisphenol-A based epoxy resin with 1st to 4th generations of den- dritic poly(amido-amine) with different amines were studied by DSC,6 but performance of the thermosets was not reported. Thus a detail and systematic study on curing at room temperature of a hyperbranched epoxy.

  4. Suspended microstructures of epoxy based photoresists fabricated with UV photolithography

    DEFF Research Database (Denmark)

    Hemanth, Suhith; Anhøj, Thomas Aarøe; Caviglia, Claudia

    2017-01-01

    In this work we present an easy, fast, reliable and low cost microfabrication technique for fabricating suspended microstructures of epoxy based photoresistswith UV photolithography. Two different fabrication processes with epoxy based resins (SU-8 and mr-DWL) using UV exposures at wavelengths...

  5. Synthesis of nanosized barium titanate/epoxy resin composites and ...

    Indian Academy of Sciences (India)

    Barium titanate/epoxy resin composites have been synthesized and tested for microwave absorption/ transmission. Nanocrystalline barium titanate (BaTiO3 or BT) ... Anechoic chamber; barium titanate; electromagnetic interference and compatibility; epoxy resin ..... electromagnetic waves, the two port calibrations have been.

  6. Surface modification of carbon/epoxy prepreg using oxygen plasma and its effect on the delamination resistance behavior of carbon/epoxy composites

    International Nuclear Information System (INIS)

    Kim, M.H.; Rhee, K.Y.; Kim, H.J.; Jung, D.H.

    2007-01-01

    It was shown in previous study that the fracture toughness of carbon/epoxy laminated composites could be significantly improved by modifying the surface of the prepreg using Ar + irradiation in an oxygen environment. In this study, the surface of carbon/epoxy prepreg was modified using an oxygen plasma to improve the delamination resistance behavior of carbon/epoxy laminated composites. The variation of the contact angle on the prepreg surface was determined as a function of the modification time, in order to determine the optimal modification time. An XPS analysis was conducted to investigate the chemical changes on the surface of the prepreg caused by the plasma modification. Mode I delamination resistance curves of the composites with and without surface modification were plotted as a function of the delamination increment. The results showed that the contact angle varied from ∼64 o to ∼47 o depending on the modification time and reached a minimum for a modification time of 30 min. The XPS analysis showed that the hydrophilic carbonyl C=O group was formed by the oxygen plasma modification. The results also showed that the delamination resistance behavior was significantly improved by the plasma modification of the prepreg. This improvement was caused by the better layer-to-layer adhesion as well as increased interfacial strength between the fibers and matrix

  7. Rational interface design of epoxy-organoclay nanocomposites: role of structure-property relationship for silane modifiers.

    Science.gov (United States)

    Bruce, Alex N; Lieber, Danielle; Hua, Inez; Howarter, John A

    2014-04-01

    Montmorillonite was modified by three silane surfactants with different functionalities to investigate the role of surfactant structure on the properties of a final epoxy-organoclay nanocomposite. N-aminopropyldimethylethoxysilane (APDMES), an aminated monofunctional silane, was chosen as a promising surfactant for several reasons: (1) it will bond to silica in montmorillonite, (2) it will bond to epoxide groups, and (3) to overcome difficulties found with trifunctional aminosilane bonding clay layers together and preventing exfoliation. A trifunctional and non-aminated version of APDMES, 3-aminopropyltriethoxysilane (APTES) and n-propyldimethylmethoxysilane (PDMMS), respectively, was also studied to provide comparison to this rationally chosen surfactant. APDMES and APTES were grafted onto montmorillonite in the same amount, while PDMMS was barely grafted (silane surfactant, neat epoxy, and epoxy-montmorillonite nanocomposite. Copyright © 2013 Elsevier Inc. All rights reserved.

  8. THERMAL PROPERTIES OF PARTICULATE EPOXY COMPOSITES

    Directory of Open Access Journals (Sweden)

    Vasile BRIA

    2010-06-01

    Full Text Available The combination of a filler with a polymer results in a new material with changed properties. Some of these changes are advantageous while others are less favorable. Polymeric dispersions of nanometer-sized metal particles offer the possibility of functionalizing the polymer by properties coming from the large number of surface atoms and the quantum-size effects. Nanosized metals show properties that differ significantly from that of bulk metals, which makes these nano-composite systems intriguing for scientific study and potentially useful for a number of technological applications. This study is about changing the epoxy properties using appropriate fillers.

  9. Metallic Coatings for Graphite/Epoxy Composites

    Science.gov (United States)

    1980-08-01

    Perforated Foil-Coated Graphite/ Epoxy Panel .............. ........................... 4-6 4-4 Two-In. -Diameter 5052 Aluminum Alloy Repair Patch...The Phase I L i4-1 I1 evaluation indicated a need for a more corrosion-resistant aluminum alloy . The coating system selected was 0.0019-in. -thick 5052 ...application techniques on moisture resistance. The selected foil was 0.0025 in.-thick, 5052 aluminum alloy perforated with 0.010-in.-dlameter holes at a

  10. Method for epoxy foam production using a liquid anhydride

    Science.gov (United States)

    Celina, Mathias [Albuquerque, NM

    2012-06-05

    An epoxy resin mixture with at least one epoxy resin of between approximately 50 wt % and 100 wt %, an anhydride cure agent of between approximately 0 wt % and approximately 50 wt %, a tert-butoxycarbonyl anhydride foaming agent of between proximately 0.1-20 wt %, a surfactant and an imidazole or similar catalyst of less than approximately 2 wt %, where the resin mixture is formed from at least one epoxy resin with a 1-10 wt % tert-butoxycarbonyl anhydride compound and an imidazole catalyst at a temperature sufficient to keep the resin in a suitable viscosity range, the resin mixture reacting to form a foaming resin which in the presence of an epoxy curative can then be cured at a temperature greater than 50.degree. C. to form an epoxy foam.

  11. Biobased Epoxy Resins from Deconstructed Native Softwood Lignin.

    Science.gov (United States)

    van de Pas, Daniel J; Torr, Kirk M

    2017-08-14

    The synthesis of novel epoxy resins from lignin hydrogenolysis products is reported. Native lignin in pine wood was depolymerized by mild hydrogenolysis to give an oil product that was reacted with epichlorohydrin to give epoxy prepolymers. These were blended with bisphenol A diglycidyl ether or glycerol diglycidyl ether and cured with diethylenetriamine or isophorone diamine. The key novelty of this work lies in using the inherent properties of the native lignin in preparing new biobased epoxy resins. The lignin-derived epoxy prepolymers could be used to replace 25-75% of the bisphenol A diglycidyl ether equivalent, leading to increases of up to 52% in the flexural modulus and up to 38% in the flexural strength. Improvements in the flexural strength were attributed to the oligomeric products present in the lignin hydrogenolysis oil. These results indicate lignin hydrogenolysis products have potential as sustainable biobased polyols in the synthesis of high performance epoxy resins.

  12. Physical aging of linear and network epoxy resins

    Science.gov (United States)

    Kong, E. S.-W.; Wilkes, G. L.; Mcgrath, J. E.; Banthia, A. K.; Mohajer, Y.; Tant, M. R.

    1981-01-01

    Network and linear epoxy resins principally based on the diglycidyl ether of bisphenol-A and its oligomers are prepared and studied using diamine and anhydride crosslinking agents. Rubber modified epoxies and a carbon fiber reinforced composite are also investigated. All materials display time-dependent changes when stored at temperatures below the glass transition temperature after quenching (sub-T/g/ annealing). Solvent sorption experiments initiated after different sub-T(g) annealing times demonstrate that the rate of solvent uptake can be indirectly related to the free volume of the epoxy resins. Residual thermal stresses and water are found to have little effect on the physical aging process, which affects the sub-T(g) properties of uniaxial carbon fiber reinforced epoxy material. Finally, the importance of the recovery phenomenon which affects the durability of epoxy glasses is considered.

  13. Epoxy matrix with triaromatic mesogenic unit in dielectric spectroscopy observation

    Science.gov (United States)

    Włodarska, Magdalena; Mossety-Leszczak, Beata; Bąk, Grzegorz W.; Kisiel, Maciej; Dłużniewski, Maciej; Okrasa, Lidia

    2018-04-01

    This paper describes the dielectric response of a selected liquid crystal epoxy monomer (plain and in curing systems) in a wide range of frequency and temperature. The dielectric spectroscopy, thanks to its sensitivity, is a very good tool for studying phase transitions, reaction progress, or material properties. This sensitivity is important in the case of liquid crystal epoxy resins, where properties of the final network depend on the choice of monomers, curing agents, curing conditions and post-curing treatment, or applying an external electric or magnetic field during the reaction. In most of the obtained cured products, the collected dielectric data show two relaxation processes. The α-process is related to a structural reorientation; it can usually be linked with the glass transition and the mechanical properties of the material. The β-process can be identified as a molecular motion process, probably associated with the carboxyl groups in the mesogen. A transient Maxwell-Wagner relaxation observed in one of the compositions after the initial curing is removed by post-curing treatment at elevated temperatures. Post-curing is therefore necessary for obtaining uniformly cured products in those cases. In the investigated systems, the choice of a curing agent can change the glass transition temperature by at least 70 °C. The obtained results are in a good agreement with an earlier study employing other techniques. Finally, we assess the influence of the direction of mesogen alignment on the dielectric properties of one selected system, where a global order was induced by applying an external magnetic field in the course of curing.

  14. Reinforcing styrene butadiene rubber with lignin-novolac epoxy resin networks

    Directory of Open Access Journals (Sweden)

    P. Yu

    2015-01-01

    Full Text Available In this study, lignin-novolac epoxy resin networks were fabricated in the styrene butadiene rubber (SBR matrix by combination of latex compounding and melt mixing. Firstly, SBR/lignin compounds were co-coagulated by SBR latex and lignin aqueous solution. Then the novolac epoxy resin (F51 was added in the SBR/lignin compounds by melt compounding method. F51 was directly cured by lignin via the ring-opening reaction of epoxy groups of F51 and OH groups (or COOH groups of lignin during the curing process of rubber compounds, as was particularly evident from Fourier transform infrared spectroscopy (FTIR studies and maximum torque of the curing analysis. The existence of lignin-F51 networks were also detected by scanning electron microscope (SEM and dynamic mechanical analysis (DMA. The structure of the SBR/lignin/F51 was also characterized by rubber process analyzer (RPA, thermogravimetric analysis (TGA and determination of crosslinking density. Due to rigid lignin-F51 networks achieved in SBR/lignin/F51 composites, it was found that the hardness, modulus, tear strength, crosslinking density, the temperature of 5 and 10% weight-loss were significantly enhanced with the loading of F51.

  15. Comparison of structural health assessment capabilities in epoxy – carbon black and epoxy – carbon nanotube nanocomposites

    Directory of Open Access Journals (Sweden)

    F. Inam

    2014-01-01

    Full Text Available A novel method for comparing structural health of different types of brittle epoxy nanocomposites filled with carbon nanostructured fillers is presented. Epoxy – 0.2 vol% carbon black (CB and epoxy – 0.2 vol% carbon nanotube (CNT nanocomposite bars were prepared by calendering and thermal curing. Nanocomposite bars were subjected to Vickers diamond indentation to produce sub-surface damage. Electrical conductivities were analysed by 4-point method to estimate the structural damage caused by indentation. For comprehensive comparison, fracture toughness and percolation threshold were analysed as well. Because of the systematically induced indentation damage, a sharp decrease of 89% was observed in the electrical conductivity of epoxy – CNT nanocomposite as compared to 25% in the electrical conductivity of epoxy – CB nanocomposite. CNTs impart superior damage sensing capability in brittle nanocomposite structures, in comparison to CB, due to their high aspect ratio (fibrous nature and high electrical conductivity.

  16. Extremely low temperature properties of epoxy GFRP

    International Nuclear Information System (INIS)

    Kadotani, Kenzo; Nagai, Matao; Aki, Fumitake.

    1983-01-01

    The examination of fiber-reinforced plastics, that is, plastics such as epoxy, polyester and polyimide reinforced with high strength fibers such as glass, carbon, boron and steel, for extremely low temperature use began from the fuel tanks of rockets. Therafter, the trial manufacture of superconducting generators and extremely low temperature transformers and the manufacture of superconducting magnets for nuclear fusion experimental setups became active, and high performance FRPs have been adopted, of which the extremely low temperature properties have been sufficiently grasped. Recently, the cryostats made of FRPs have been developed, fully utilizing such features of FRPs as high strength, high rigidity, non-magnetic material, insulation, low heat conductivity, light weight and the freedom of molding. In this paper, the mechanical properties at extremely low temperature of the plastic composite materials used as insulators and structural materials for extremely low temperature superconducting equipment is outlined, and in particular, glass fiber-reinforced epoxy laminates are described somewhat in detail. The fracture strain of GFRP at extremely low temperature is about 1.3 times as large as that at room temperature, but at extremely low temperature, clear cracking occurred at 40% of the fracture strain. The linear thermal contraction of GFRP showed remarkable anisotropy. (Kako, I.)

  17. Epoxy Crosslinked Silica Aerogels (X-Aerogels)

    Science.gov (United States)

    fabrizio, Eve; Ilhan, Faysal; Meador, Mary Ann; Johnston, Chris; Leventis, Nicholas

    2004-01-01

    NASA is interested in the development of strong lightweight materials for the dual role of thermal insulator and structural component for space vehicles; freeing more weight for useful payloads. Aerogels are very-low density materials (0.010 to 0.5 g/cc) that, due to high porosity (meso- and microporosity), can be, depending on the chemical nature of the network, ideal thermal insulators (thermal conductivity approx. 15 mW/mK). However, aerogels are extremely fragile. For practical application of aerogels, one must increase strength without compromising the physical properties attributed to low density. This has been achieved by templated growth of an epoxy polymer layer that crosslinks the "pearl necklace" network of nanoparticles: the framework of a typical silica aerogel. The requirement for conformal accumulation of the epoxy crosslinker is reaction both with the surface of silica and with itself. After cross-linking, the strength of a typical aerogel monolith increases by a factor of 200, in the expense of only a 2-fold increase in density. Strength is increased further by coupling residual unreacted epoxides with diamine.

  18. Epoxy Sol-Gel Hybrid Thermosets

    Directory of Open Access Journals (Sweden)

    Angels Serra

    2016-02-01

    Full Text Available Sol-gel methodologies are advantageous in the preparation of hybrid materials in front of the conventional addition of nanoparticles, because of the fine dispersion of the inorganic phase that can be reached in epoxy matrices. In addition, the use of organoalkoxysilanes as coupling agents allows covalent linkage between organic and inorganic phases, which is the key point in the improvement of mechanical properties. The sol-gel process involves hydrolysis and condensation reactions under mild conditions, starting from hydrolysable metal alkoxides, generally alkoxy silanes. Using the sol-gel procedure, the viscosity of the formulation is maintained, which is an important issue in coating applications, whereas the transparency of the polymer matrix is also maintained. However, only the proper combination of the chemistries and functionalities of both organic and inorganic structures leads to thermosets with the desired characteristics. The adequate preparation of hybrid epoxy thermosets enables their improvement in characteristics such as mechanical properties (modulus, hardness, scratch resistance, thermal and flame resistance, corrosion and antimicrobial protection, and even optical performance among others.

  19. Monitoring and simulations of hydrolysis in epoxy matrix composites during hygrothermal aging

    KAUST Repository

    El Yagoubi, Jalal

    2015-01-01

    In this paper, we studied the water transport in thermoset matrices. We used Fourier Transform Infrared analysis (FTIR) during sorption/desorption experiments to investigate the interaction between sorbed water and the epoxy network. Our results demonstrated that the polymer matrix undergoes hydrolysis. We found that the chemical species involved in the reaction process was the residual anhydride groups. These results support the physical basis of the three-dimensional (3D) diffusion/reaction model. We finally showed that this model is able to reproduce multi-cycle sorption/desorption experiment, as well as water uptake in hybrid metal/epoxy samples. We simulated the 3D distributions of the diffusing water and the reacted water.

  20. Current-Voltage Characteristics of the Composites Based on Epoxy Resin and Carbon Nanotubes

    Directory of Open Access Journals (Sweden)

    Iwona Pełech

    2015-01-01

    Full Text Available Polymer composites based on epoxy resin were prepared. Multiwalled carbon nanotubes synthesized on iron-cobalt catalyst were applied as a filler in a polymer matrix. Chlorine or hydroxyl groups were incorporated on the carbon nanotubes surface via chlorination or chlorination followed by hydroxylation. The effect of functionalized carbon nanotubes on the epoxy resin matrix is discussed in terms of the state of CNTs dispersion in composites as well as electrical properties. For the obtained materials current-voltage characteristics were determined. They had a nonlinear character and were well described by an exponential-type equation. For all the obtained materials the percolation threshold occurred at a concentration of about 1 wt%. At a higher filler concentration >2 wt%, better conductivity was demonstrated by polymer composites with raw carbon nanotubes. At a lower filler concentration <2 wt%, higher values of electrical conductivity were obtained for polymer composites with modified carbon nanotubes.

  1. Epoxy Resins Toughened with Surface Modified Epoxidized Natural Rubber Fibers by One-Step Electrospinning.

    Science.gov (United States)

    Kim, Joo Ran; Kim, Jung J

    2017-04-27

    Epoxidized natural rubber fibers (ERFs) are developed through one-step electrospinning and directly deposited into epoxy resins without collecting and distributing of fibers. The shape of ERFs shows rough surface due to different evaporation rate of solvent mixture consisting of chloroform and dichloromethane and the average diameter of ERFs is 6.2 µm. The increase of ERFs loading from 0 to 20 wt % into the epoxy resin increases the fracture strain significantly from 1.2% to 13% and toughness from 0.3 MPa to 1.9 MPa by a factor of 7. However, the tensile strength and Young's modulus decrease about 34% from 58 MPa to 34 MPa and from 1.4 GPa to 0.9 GPa, respectively. Due to the crosslinking reactions between oxirane groups of ERFs and amine groups in the resin, surface roughness and the high aspect ratio of ERFs, ERFs result in more effective toughening effect with the minimum loss of tensile properties in epoxy resins.

  2. Epoxy Resins Toughened with Surface Modified Epoxidized Natural Rubber Fibers by One-Step Electrospinning

    Directory of Open Access Journals (Sweden)

    Joo Ran Kim

    2017-04-01

    Full Text Available Epoxidized natural rubber fibers (ERFs are developed through one-step electrospinning and directly deposited into epoxy resins without collecting and distributing of fibers. The shape of ERFs shows rough surface due to different evaporation rate of solvent mixture consisting of chloroform and dichloromethane and the average diameter of ERFs is 6.2 µm. The increase of ERFs loading from 0 to 20 wt % into the epoxy resin increases the fracture strain significantly from 1.2% to 13% and toughness from 0.3 MPa to 1.9 MPa by a factor of 7. However, the tensile strength and Young’s modulus decrease about 34% from 58 MPa to 34 MPa and from 1.4 GPa to 0.9 GPa, respectively. Due to the crosslinking reactions between oxirane groups of ERFs and amine groups in the resin, surface roughness and the high aspect ratio of ERFs, ERFs result in more effective toughening effect with the minimum loss of tensile properties in epoxy resins.

  3. Fracture behavior of nano-scale rubber-modified epoxies

    Science.gov (United States)

    Bacigalupo, Lauren N.

    The primary focus of the first portion of this study is to compare physical and mechanical properties of a model epoxy that has been toughened with one of three different types of rubber-based modifier: a traditional telechelic oligomer (phase separates into micro-size particles), a core-shell latex particle (preformed nano-scale particles) and a triblock copolymer (self-assembles into nano-scale particles). The effect of modifier content on the physical properties of the matrix was determined using several thermal analysis methods, which provided insight into any inherent alterations of the epoxy matrix. Although the primary objective is to study the role of particle size on the fracture toughness, stiffness and strength were also determined since these properties are often reduced in rubber-toughened epoxies. It was found that since the CSR- and SBM-modified epoxies are composed of less rubber, thermal and mechanical properties of the epoxy were better maintained. In order to better understand the fracture behavior and mechanisms of the three types of rubber particles utilized in this study, extensive microscopy analysis was conducted. Scanning transmission electron microscopy (STEM) was used to quantify the volume fraction of particles, transmission optical microscopy (TOM) was used to determine plastic damage zone size, and scanning electron microscopy (SEM) was used to assess void growth in the plastic zone after fracture. By quantifying these characteristics, it was then possible to model the plastic damage zone size as well as the fracture toughness to elucidate the behavior of the rubber-modified epoxies. It was found that localized shear yielding and matrix void growth are the active toughening mechanisms in all rubber-modified epoxies in this study, however, matrix void growth was more prevalent. The second portion of this study investigated the use of three acrylate-based triblocks and four acrylate-based diblocks to modify a model epoxy system. By

  4. Catalyzed Synthesis and Characterization of a Novel Lignin-Based Curing Agent for the Curing of High-Performance Epoxy Resin

    Directory of Open Access Journals (Sweden)

    Saeid Nikafshar

    2017-07-01

    Full Text Available In this study, lignin, an aromatic compound from the forestry industry, was used as a renewable material to synthesize a new aromatic amine curing agent for epoxy resin. Firstly, lignin was separated from black liquor and hydroxyl groups were converted to tosyl groups as leaving groups. Then, primary amination was conducted using an ammonia solution at high pressure and temperature, in the presence of a nano-alumina-based catalyst. The structure of the nanocatalyst was confirmed by FT-IR, ICP, SEM, and XPS analyses. According to the FT-IR spectra, a demethylation reaction, the substitution of hydroxyl groups with tosyl groups, and then an amination reaction were successfully performed on lignin, which was further confirmed by the 13C NMR and CHNS analyses. The active hydrogen equivalent of aminated lignin was determined and three samples with 9.9 wt %, 12.9 wt %, and 15.9 wt % of aminated lignin, as curing agents, were prepared for curing the diglycidyl ether of bisphenol A (DGEBA. The thermal characteristics of the curing process of these epoxy samples were determined by DSC and TGA analyses. Moreover, the mechanical performance of the cured epoxy systems, e.g., the tensile strength and Izod impact strength, were measured, showing that in the presence of 12.9 wt % aminated lignin, the mechanical properties of the aminated lignin-epoxy system exhibited the best performance, which was competitive, compared to the epoxy systems cured by commercial aromatic curing agents.

  5. Enhancement of mechanical properties of epoxy/graphene nanocomposite

    Science.gov (United States)

    Berhanuddin, N. I. C.; Zaman, I.; Rozlan, S. A. M.; Karim, M. A. A.; Manshoor, B.; Khalid, A.; Chan, S. W.; Meng, Q.

    2017-10-01

    Graphene is a novel class of nanofillers possessing outstanding characteristics including most compatible with most polymers, high absolute strength, high aspect ratio and cost effectiveness. In this study, graphene was used to reinforce epoxy as a matrix, to enhance its mechanical properties. Two types of epoxy composite were developed which are epoxy/graphene nanocomposite and epoxy/modified graphene nanocomposite. The fabrication of graphene was going through thermal expansion and sonication process. Chemical modification was only done for modified graphene where 4,4’-Methylene diphenyl diisocyanate (MDI) is used. The mechanical properties of both nanocomposite, such as Young’s modulus and maximum stress were investigated. Three weight percentage were used for this study which are 0.5 wt%, 1.0 wt% and 1.5 wt%. At 0.5 wt%, modified and unmodified shows the highest value compared to neat epoxy, where the value were 8 GPa, 6 GPa and 0.675 GPa, respectively. For maximum stress, neat epoxy showed the best result compared to both nanocomposite due to the changes of material properties when adding the filler into the matrix. Therefore, both nanocomposite increase the mechanical properties of the epoxy, however modification surface of graphene gives better improvement.

  6. Novel spirocyclic phosphazene-based epoxy resin for halogen-free fire resistance: synthesis, curing behaviors, and flammability characteristics.

    Science.gov (United States)

    Sun, Jian; Wang, Xiaodong; Wu, Dezhen

    2012-08-01

    A novel halogen-free fire resistant epoxy resin with pendent spiro-cyclotriphosphazene groups was designed and synthesized via a three-step synthetic pathway. The chemical structures and compositions of spiro-cyclotriphosphazene precursors and final product were confirmed by (1)H, (13)C, and (31)P NMR spectroscopy, mass spectroscopy, elemental analysis, and Fourier transform infrared spectroscopy. The thermal curing behaviors of the synthesized epoxy resin with 4,4'-diamino-diphenylmethane, 4,4'-diamino-diphenyl sulfone, and novolac as hardeners were investigated by differential scanning calorimetry (DSC), and the curing kinetics were also studied under a nonisothermal condition. The evaluation of the thermal properties demonstrated that these thermosets achieved a good thermal resistance due to their high glass transition temperatures more than 150 °C, and also gained high thermal stabilities with high char yields. The flammability characteristics of the spirocyclic phosphazene-based epoxy thermosets cured with these three hardeners were investigated on the basis of the results obtained from the limiting oxygen index (LOI) and UL-94 vertical burning experiments as well as the analysis of the residual chars collected from the vertical burning tests. The high LOI values and UL-94 V-0 classification of these epoxy thermosets indicated that the incorporation of phosphazene rings into the backbone chain imparts nonflammability to the epoxy resin owing to the unique combination of phosphorus and nitrogen following by a synergistic effect on flame retardancy. The epoxy resin obtained in this study is a green functional polymer and will become a potential candidate for fire- and heat-resistant applications in electronic and microelectronic fields with more safety and excellent performance.

  7. Surface and buried interfacial structures of epoxy resins used as underfills studied by sum frequency generation vibrational spectroscopy.

    Science.gov (United States)

    Vázquez, Anne V; Holden, Brad; Kristalyn, Cornelius; Fuller, Mike; Wilkerson, Brett; Chen, Zhan

    2011-05-01

    Flip chip technology has greatly improved the performance of semiconductor devices, but relies heavily on the performance of epoxy underfill adhesives. Because epoxy underfills are cured in situ in flip chip semiconductor devices, understanding their surface and interfacial structures is critical for understanding their adhesion to various substrates. Here, sum frequency generation (SFG) vibrational spectroscopy was used to study surface and buried interfacial structures of two model epoxy resins used as underfills in flip chip devices, bisphenol A digylcidyl ether (BADGE) and 1,4-butanediol diglycidyl ether (BDDGE). The surface structures of these epoxies were compared before and after cure, and the orientations of their surface functional groups were deduced to understand how surface structural changes during cure may affect adhesion properties. Further, the effect of moisture exposure, a known cause of adhesion failure, on surface structures was studied. It was found that the BADGE surface significantly restructured upon moisture exposure while the BDDGE surface did not, showing that BADGE adhesives may be more prone to moisture-induced delamination. Lastly, although surface structure can give some insight into adhesion, buried interfacial structures more directly correspond to adhesion properties of polymers. SFG was used to study buried interfaces between deuterated polystyrene (d-PS) and the epoxies before and after moisture exposure. It was shown that moisture exposure acted to disorder the buried interfaces, most likely due to swelling. These results correlated with lap shear adhesion testing showing a decrease in adhesion strength after moisture exposure. The presented work showed that surface and interfacial structures can be correlated to adhesive strength and may be helpful in understanding and designing optimized epoxy underfill adhesives.

  8. Self-healing of fatigue crack in epoxy materials with epoxy/mercaptan system

    Directory of Open Access Journals (Sweden)

    2011-01-01

    Full Text Available Successful retardation or arrest of fatigue crack is observed in self-healing epoxy composite containing dual encapsulated healant, i.e. two types of microcapsules that respectively include epoxy prepolymer and mercaptan/tertiary amine hardener. Fast curing of the released healing agent from the broken capsules leads to rapid development of its bonding strength and fracture toughness at room temperature. It is found that the effects of microcapsules induced-toughening, hydrodynamic pressure crack tip shielding, polymeric wedge and adhesive bonding of the healing agent are responsible for the extension of fatigue life. Depending on the applied stress intensity range, ΔKI, and the competition between polymerization kinetics of the healing agent and crack growth rate, the above mechanisms exert different influences on crack retardation. The results might serve as a reference for further improving the performance of the healant system under fatigue circumstances.

  9. Development and Characterization of Novel Interpenetrating Network (IPN Foams from Epoxy Ester and Aliphatic Epoxy Resin

    Directory of Open Access Journals (Sweden)

    Kanuprasad Patel

    2009-01-01

    Full Text Available Diglycidyl ether of bisphenol-A (DGEBA was reacted with acrylate monomer at variable molar ratios. The reaction between glycerine and epichlorohydrine form glycidyl ether of polyol aliphatic epoxy resin. The resultant resins were characterized duly. Both the resins were mixed at different ratios with constant high shear stirring. The obtained mixture and suitable additives were heated at 150oC for one and half hour. The so called Interpenetrating Network (IPN transformed into foams. The performance of foams was evaluated by testing for compression in both parallel and perpendicular to rise direction. The tests were carried out at room temperature and at the elevated temperature. The compression properties showed a decreasing trend for increasing amounts of glycerine resin. The density and thermal properties of epoxy foams were also evaluated. The relation between the composition, density and properties of the foam was analyzed.

  10. Effect of Glass Reinforced Epoxy (GRE) pipe filled with Geopolymer Materials for Piping Application: Compression Properties

    OpenAIRE

    Abu Hashim Mohammad Firdaus; Abdullah Mohd Mustafa Al Bakri; Ghazali Che Mohd Ruzaidi; Hussin Kamarudin; Binhussain Mohammed; Omar Mohd Firdaus

    2016-01-01

    The aim of this paper is to achieve the highest compressive strength of glass reinforced epoxy pipe with the geopolymer filler content of weight percentage that were used in glass reinforced epoxy pipe. The samples were prepared by using the filament winding method. The effect of weight percentage of geopolymer materials in epoxy hardener was studied under mechanical testing, which is using the compression test. A series of glass reinforced epoxy pipe and glass reinforced epoxy pipe filled wi...

  11. Plant Oil-Derived Epoxy Polymers toward Sustainable Biobased Thermosets.

    Science.gov (United States)

    Wang, Zhongkai; Yuan, Liang; Ganewatta, Mitra S; Lamm, Meghan E; Rahman, Md Anisur; Wang, Jifu; Liu, Shengquan; Tang, Chuanbing

    2017-06-01

    Epoxy polymers (EPs) derived from soybean oil with varied chemical structures are synthesized. These polymers are then cured with anhydrides to yield soybean-oil-derived epoxy thermosets. The curing kinetic, thermal, and mechanical properties are well characterized. Due to the high epoxide functionality per epoxy polymer chain, these thermosets exhibit tensile strength over an order of magnitude higher than a control formulation with epoxidized soybean oil. More importantly, thermosetting materials ranging from soft elastomers to tough thermosets can be obtained simply by using different EPs and/or by controlling feed ratios of EPs to anhydrides. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  12. Hansen solubility parameters for a carbon fiber/epoxy composite

    DEFF Research Database (Denmark)

    Launay, Helene; Hansen, Charles M.; Almdal, Kristoffer

    2007-01-01

    In this study, the physical affinity between an epoxy matrix and oxidized, unsized carbon fibers has been evaluated using Hansen solubility (cohesion) parameters (HSP). A strong physical compatibility has been shown, since their respective HSP are close. The use of a glassy carbon substrate...... as a model for unsized carbon fiber has been demonstrated as appropriate for the study of interactions between the materials in composite carbon fiber-epoxy systems. The HSP of glassy carbon are similar to those of carbon fibers and epoxy matrix. (C) 2007 Elsevier Ltd. All rights reserved....

  13. Thermomechanical Behavior of High Performance Epoxy/Organoclay Nanocomposites

    Directory of Open Access Journals (Sweden)

    Artur Soares Cavalcanti Leal

    2014-01-01

    Full Text Available Nanocomposites of epoxy resin containing bentonite clay were fabricated to evaluate the thermomechanical behavior during heating. The epoxy resin system studied was prepared using bifunctional diglycidyl ether of bisphenol A (DGEBA, crosslinking agent diaminodiphenylsulfone (DDS, and diethylenetriamine (DETA. The purified bentonite organoclay (APOC was used in all experiments. The formation of nanocomposite was confirmed by X-ray diffraction analysis. Specimens of the fabricated nanocomposites were characterized by dynamic mechanical analysis (DMA. According to the DMA results a significant increase in glass transition temperature and storage modulus was evidenced when 1 phr of clay is added to epoxy resin.

  14. Generalized morphea/eosinophilic fasciitis overlap after epoxy exposure

    Directory of Open Access Journals (Sweden)

    Warren H. Chan, MS

    2018-03-01

    Full Text Available Generalized morphea is associated with epoxy resin vapors and is characterized by the development of lesions shortly after exposure. Morphea presenting along with eosinophilic fasciitis (EF, or morphea/EF overlap, is rare and an indicator of poor prognosis and resistance to treatment. Here we present a case of generalized morphea/EF overlap linked to epoxy exposure. Our patient received multiple therapies—ultraviolet A1 phototherapy, prednisone, methotrexate, azathioprine, mycophenolate mofetil, cyclophosphamide, cyclosporine, and rituximab—none of which led to a significant response. The refractory nature of this disease warrants vigilance in its association with epoxy exposure.

  15. Crystal structure of (1R,2S,4R,7R,8S,9R-3,3-dichloro-8,9-epoxy-4,8,12,12-tetramethyltricyclo[5.5.0.02,4]dodecane

    Directory of Open Access Journals (Sweden)

    Ahmed Benzalim

    2015-08-01

    Full Text Available The title compound, C16H24Cl2O, is built up from two fused six- and seven-membered rings which bear a dichlorocyclopropane group and an epoxy group, respectively. In the molecule, the six-membered ring adopts an envelope configuration with the C atom linking the epoxy ring at the flap, while the seven-membered ring adopts a boat–sofa conformation.

  16. Mechanical properties of Epon 826/DEA epoxy

    Science.gov (United States)

    Jordan, Jennifer L.; Foley, Jason R.; Siviour, Clive R.

    2008-09-01

    Polymers are becoming increasingly used in aerospace structural applications, where they experience complex, non-static loads. Correspondingly, the mechanical properties at high strain rates are of increasing importance in these applications. This paper investigates the compressive properties of Epon 826 epoxy resin cured with diethynolamine (DEA) across strain rates from 10-3 to 104 s-1. Specimens were tested using an Instron mechanical testing machine for static loading, traditional split Hopkinson pressure bars (SHPBs) for high strain rates, and a miniaturized SHPB for ultra-high strain rates. Additionally, the material was tested using dynamic mechanical analysis to determine the effects of time and temperature equivalences on the strain rate behavior of the samples. The experimental data is used to fit the Mulliken-Boyce model, modified for one-dimension, which is able to capture the compressive mechanical properties over a range of strain rates.

  17. Epoxy resins used to seal brachytherapy seed

    International Nuclear Information System (INIS)

    Ferreira, Natalia Carolina Camargos; Ferraz, Wilmar Barbosa; Reis, Sergio Carneiro dos; Santos, Ana Maria Matildes dos

    2013-01-01

    Prostate cancer treatment with brachytherapy is recommended for patients with cancer at an early stage. In this treatment, small radioactive seeds are implanted directly in the prostate gland. These seeds are composed at least of one radionuclide carrier and an X-ray marker enclosed within a metallic tube usually sealed by laser process. This process is expensive and, furthermore, it can provoke a partial volatilization of the radionuclide and change the isotropy in dose distribution around the seed. In this paper, we present a new sealing process using epoxy resin. Three kinds of resins were utilized and characterized by scanning electron microscopy (SEM), energy dispersive X ray (EDS) and by differential scanning calorimetry (DSC) after immersion in simulated body fluid (SBF) and in sodium iodine solution (NaI). The sealing process showed excellent potential to replace the sealing laser usually employed. (author)

  18. Cellulose whisker/epoxy resin nanocomposites.

    Science.gov (United States)

    Tang, Liming; Weder, Christoph

    2010-04-01

    New nanocomposites composed of cellulose nanofibers or "whiskers" and an epoxy resin were prepared. Cellulose whiskers with aspect ratios of approximately 10 and approximately 84 were isolated from cotton and sea animals called tunicates, respectively. Suspensions of these whiskers in dimethylformamide were combined with an oligomeric difunctional diglycidyl ether of bisphenol A with an epoxide equivalent weight of 185-192 and a diethyl toluenediamine-based curing agent. Thin films were produced by casting these mixtures and subsequent curing. The whisker content was systematically varied between 4 and 24% v/v. Electron microscopy studies suggest that the whiskers are evenly dispersed within the epoxy matrix. Dynamic mechanical thermoanalysis revealed that the glass transition temperature (T(g)) of the materials was not significantly influenced by the incorporation of the cellulose filler. Between room temperature and 150 degrees C, i.e., below T(g), the tensile storage moduli (E') of the nanocomposites increased modestly, for example from 1.6 GPa for the neat polymer to 4.9 and 3.6 GPa for nanocomposites comprising 16% v/v tunicate or cotton whiskers. The relative reinforcement was more significant at 185 degrees C (i.e., above T(g)), where E' was increased from approximately 16 MPa (neat polymer) to approximately 1.6 GPa (tunicate) or approximately 215 MPa (cotton). The mechanical properties of the new materials are well-described by the percolation model and are the result of the formation of a percolating whisker network in which stress transfer is facilitated by strong interactions between the whiskers.

  19. Degradation of epoxy coatings under gamma irradiation

    International Nuclear Information System (INIS)

    Djouani, F.; Zahra, Y.; Fayolle, B.; Kuntz, M.; Verdu, J.

    2013-01-01

    Epoxy networks based on Diglycidyl ether of bisphenol A (DGEBA) and cured with Jeffamine® (POPA) or polyamidoamine (PAA) were gamma irradiated at 25 °C in air. Dose rates of 50, 200 or 2000 Gy h −1 for doses up 100 kGy were used. Structural changes were monitored by IR spectrophotometry, DSC and sol–gel analysis. Both networks display some common features: for I≥200 Gy h −1 , reaction products grow proportionally to time and the rate is a decreasing function of dose rate. The simplest explanation is that peroxy radicals are the main precursors of these products (in the dose rate domain under study), through a unimolecular rearrangement of which an hypothetical mechanism is proposed. DGEBA–POPA are more reactive then DGEBA–PAA networks (according to IR criteria), that can be attributed to the high reactivity of tertiary CH bands in polyoxypropylene segments. The oxidation of these sites leads to methyl ketones. A simple kinetic model in which methyl ketones result from rearrangements of tertiary peroxyls and from tertiary alkoxyls was proposed. It leads to an expression of the radiochemical yield of methyl ketones (G(MK)) of the form G(MK)=a+bI −1/2 where a and b are parameters depending of elementary rate constants. Experimental G(MK) values are reasonably well fitted by this equation. In DGEBA–PAA networks, a wide variety of oxidation products, among which amides predominate, can be observed. In these networks, chain scissions predominate over crosslinking, whereas a slight predominance of crosslinking was observed, at least for the lowest dose rate, in DGEBA–POPA. - Highlights: ► The effects of irradiation at three distinct dose rates have been studied on two epoxy networks. ► DGEBA–polyamidoamine networks appear more stable than DGEBA–polyoxypropylene diamine ones. ► A simple kinetic model involving methyl ketones is proposed.

  20. Preparation and characterization of polyhedral oligomer silsesquioxane nanocomposites incorporated in epoxy resin

    International Nuclear Information System (INIS)

    Longhi, Marielen; Zini, Lucas Pandolphi; Birriel, Eliena Jonko; Kunst, Sandra Raquel; Zattera, Ademir Jose

    2015-01-01

    The incorporation of nanofiller in thermosetting like epoxy resin as has been studied in order to modify its properties. In this research, nanocomposites were obtained by incorporating 5% by weight of three polyhedral oligomeric silsesquioxane (POSS) with different number of functionalization: Glicidilisobutil-POSS, Triglicidilisobutil- POSS and Glicicil POSS in an epoxy matrix by sonification process. The nanocomposites were characterized by analysis of X-ray diffraction (DRX), transmission electron microscopy (TEM) and thermogravimetric analysis (TGA). The DRX analysis showed the characteristic peak of POSS and TEM images showed that there is a difference in the dispersion of nanocages for the difference in the number of epoxy groups on the POSS. The incorporation of Glicidilisobutil-POSS showed a significant increase in the glass transition temperature (Tg) value, and also that the most effective from the viewpoint of the dispersion, on the other hand, the Glycidyl-POSS had a greater influence on the thermal stability demonstrating that the dispersion medium is an important characteristic to define the most desirable properties. (author)

  1. Tuning the adhesion between polyimide substrate and MWCNTs/epoxy nanocomposite by surface treatment

    Science.gov (United States)

    Bouhamed, Ayda; Kia, Alireza Mohammadian; Naifar, Slim; Dzhagan, Volodymyr; Müller, Christian; Zahn, Dietrich R. T.; Choura, Slim; Kanoun, Olfa

    2017-11-01

    MWCNTs/epoxy nanocomposite thin films are coated on the polyimide (PI) flexible substrate, to be used as a strain sensor. Previous studies showed that the adhesion between polyimide and other materials are very poor. In this work, two approaches, oxygen plasma cleaning and simple solvent cleaning are performed for activation of the polyimide surface. In order to understand the impact of both cleaning techniques, the physicochemical properties of PI are measured and characterized using contact angle measurements (CAMs), X-ray photoelectron spectroscopy(XPS), and atomic force microscopy (AFM). In addition, the adhesion properties of PI/[MWCNTs/epoxy] systems by varying surface treatment time are investigated and evaluated using force-distance measurements by AFM. The results illustrate that the activated surface exhibits higher surface energy for oxygen plasma cleaning in comparison with the solvent cleaning method. The improvement can be related to the increase of oxygen concentration, which is accompanied by the enhancement of the polar component to 53.79 mN/m due to the formation of functional groups on the surface and the change of the substrate surface roughness from 1.72 nm to 15.5 nm. As a result, improved adhesion was observed from force-distance measurement between PI/[MWCNTs/epoxy] systems due to oxygen plasma effects.

  2. Effect of Zirconia Nanoparticles in Epoxy-Silica Hybrid Adhesives to Join Aluminum Substrates

    Directory of Open Access Journals (Sweden)

    José de Jesús Figueroa-Lara

    2017-09-01

    Full Text Available This research presents the interaction of the epoxy polymer diglicydil ether of bisphenol-A (DGEBA with silica (SiO2 nanoparticles plus zirconia (ZrO2 nanoparticles obtained via the sol-gel method in the synthesis of an epoxy-silica-zirconia hybrid adhesive cured with polyamide. ZrO2 nanoparticles were added to the epoxy-silica hybrid adhesive produced in situ to modify the apparent shear strength of two adhesively bonded aluminum specimens. The results showed that the addition of different amounts of ZrO2 nanoparticles increased the shear strength of the adhesively bonded aluminum joint, previously treated by sandblasting, immersion in hot water and silanized with a solution of hydrolyzed 3-glycidoxipropyltrimethoxysilane (GPTMS. The morphology and microstructure of the nanoparticles and aluminum surfaces were examined by scanning electron microscopy (SEM, and elemental analysis was performed with the Energy-dispersive X-ray spectroscopy (EDS detector; the chemical groups were investigated during the aluminum surface modification using Fourier transform infrared spectroscopy (FTIR.

  3. Formation of interfacial network structure via photo-crosslinking in carbon fiber/epoxy composites

    Directory of Open Access Journals (Sweden)

    S. H. Deng

    2014-07-01

    Full Text Available A series of diblock copolymers (poly(n-butylacrylate-co-poly(2-hydroxyethyl acrylate-b-poly(glycidyl methacrylate ((PnBA-co-PHEA-b-PGMA, containing a random copolymer block PnBA-co-PHEA, were successfully synthesized by atom transfer radical polymerization (ATRP. After being chemically grafted onto carbon fibers, the photosensitive methacrylic groups were introduced into the random copolymer, giving a series of copolymers (poly(n-butylacrylate-co-poly(2-methacryloyloxyethyl acrylate-b-poly(glycidyl methacrylate((PnBA-co-PMEA-b-PGMA. Dynamic mechanical analysis indicated that the random copolymer block after ultraviolet (UV irradiation was a lightly crosslinked polymer and acted as an elastomer, forming a photo-crosslinked network structure at the interface of carbon fiber/epoxy composites. Microbond test showed that such an interfacial network structure greatly improved the cohesive strength and effectively controlled the deformation ability of the flexible interlayer. Furthermore, three kinds of interfacial network structures, i physical crosslinking by H-bonds, ii chemical crosslinking by photopolymerization, and iii interpenetrating crosslinked network by photopolymerization and epoxy curing reaction were received in carbon fiber/epoxy composite, depending on the various preparation processes.

  4. Flexible Epoxy Resin Formed Upon Blending with a Triblock Copolymer through Reaction-Induced Microphase Separation

    Science.gov (United States)

    Chu, Wei-Cheng; Lin, Wei-Sheng; Kuo, Shiao-Wei

    2016-01-01

    In this study, we used diglycidyl ether bisphenol A (DGEBA) as a matrix, the ABA block copolymer poly(ethylene oxide–b–propylene oxide–b–ethylene oxide) (Pluronic F127) as an additive, and diphenyl diaminosulfone (DDS) as a curing agent to prepare flexible epoxy resins through reaction-induced microphase separation (RIMPS). Fourier transform infrared spectroscopy confirmed the existence of hydrogen bonding between the poly(ethylene oxide) segment of F127 and the OH groups of the DGEBA resin. Small-angle X-ray scattering, atomic force microscopy, and transmission electron microscopy all revealed evidence for the microphase separation of F127 within the epoxy resin. Glass transition temperature (Tg) phenomena and mechanical properties (modulus) were determined through differential scanning calorimetry and dynamic mechanical analysis, respectively, of samples at various blend compositions. The modulus data provided evidence for the formation of wormlike micelle structures, through a RIMPS mechanism, in the flexible epoxy resin upon blending with the F127 triblock copolymer. PMID:28773571

  5. Flexible Epoxy Resin Formed Upon Blending with a Triblock Copolymer through Reaction-Induced Microphase Separation

    Directory of Open Access Journals (Sweden)

    Wei-Cheng Chu

    2016-06-01

    Full Text Available In this study, we used diglycidyl ether bisphenol A (DGEBA as a matrix, the ABA block copolymer poly(ethylene oxide–b–propylene oxide–b–ethylene oxide (Pluronic F127 as an additive, and diphenyl diaminosulfone (DDS as a curing agent to prepare flexible epoxy resins through reaction-induced microphase separation (RIMPS. Fourier transform infrared spectroscopy confirmed the existence of hydrogen bonding between the poly(ethylene oxide segment of F127 and the OH groups of the DGEBA resin. Small-angle X-ray scattering, atomic force microscopy, and transmission electron microscopy all revealed evidence for the microphase separation of F127 within the epoxy resin. Glass transition temperature (Tg phenomena and mechanical properties (modulus were determined through differential scanning calorimetry and dynamic mechanical analysis, respectively, of samples at various blend compositions. The modulus data provided evidence for the formation of wormlike micelle structures, through a RIMPS mechanism, in the flexible epoxy resin upon blending with the F127 triblock copolymer.

  6. Screening of epoxy systems for high performance filament winding applications

    Science.gov (United States)

    Chiao, T. T.; Jessop, E. S.; Penn, L.

    1975-01-01

    Several promising epoxy systems for high performance filament winding applications are described. Viscosities, gel times, and cast resin tensile behavior are given, as well as heat deflection under load and water absorption measurements.

  7. Bond strength of urethane and epoxy-modified adhesives

    Energy Technology Data Exchange (ETDEWEB)

    Childress, F.G.; Zava, A.K.; Miller, C.E.

    1976-04-26

    A number of urethane and epoxy-modified urethane systems were evaluated as room-temperature-curing adhesives. The systems were formulated to yield a variety of modulus levels and to be compatible with certain chemically sensitive materials.

  8. DEEP IMPACT/EPOXI DOCUMENTATION SET V3.0

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set contains version 3.0 of the updated collection of documentation for the raw and calibrated science data sets for the Deep Impact and EPOXI missions....

  9. Behaviour of Epoxy Silica Nanocomposites Under Static and Creep Loading

    Science.gov (United States)

    Constantinescu, Dan Mihai; Picu, Radu Catalin; Sandu, Marin; Apostol, Dragos Alexandru; Sandu, Adriana; Baciu, Florin

    2017-12-01

    Specific manufacturing technologies were applied for the fabrication of epoxy-based nanocomposites with silica nanoparticles. For dispersing the fillers in the epoxy resin special equipment such as a shear mixer and a high energy sonicator with temperature control were used. Both functionalized and unfunctionalized silica nanoparticles were added in three epoxy resins. The considered filling fraction was in most cases 0.1, 0.3 and 0.5 wt%.. The obtained nanocomposites were subjected to monotonic uniaxial and creep loading at room temperature. The static mechanical properties were not significantly improved regardless the filler percentage and type of epoxy resin. Under creep loading, by increasing the stress level, the nanocomposite with 0.1 wt% silica creeps less than all other materials. Also the creep rate is reduced by adding silica nanofillers.

  10. Epoxy coatings electrodeposited on aluminium and modified aluminium surfaces

    Directory of Open Access Journals (Sweden)

    Lazarević Zorica Ž.

    2002-01-01

    Full Text Available The corrosion behaviour and thermal stability of epoxy coatings electrodeposited on modified aluminum surfaces (anodized, phosphatized and chromatized-phosphatized aluminium were monitored during exposure to 3% NaCl solution, using electrochemical impedance spectroscopy (EIS and thermogravimetric analysis (TGA. Better protective properties of the epoxy coatings on anodized and chromatized-phosphatized aluminum with respect to the same epoxy coatings on aluminum and phosphatized aluminum were obtained: higher values of Rp and Rct and smaller values of Cc and Cd, from EIS, and a smaller amount of absorbed water inside the coating, from TGA. On the other hand, a somewhat lower thermal stability of these coatings was obtained (smaller values of the ipdt temperature. This behavior can be explained by the less porous structure of epoxy coatings on anodized and chromatized-phosphatized aluminum, caused by a lower rate of H2 evolution and better wet ability.

  11. EPOXI INFLIGHT CALIBRATIONS - HRIV RAW IMAGES V1.0

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set contains raw calibration images acquired by the Deep Impact Medium Resolution Visible CCD from 04 October 2007 through 17 December 2008 for the EPOXI...

  12. EPOXI INFLIGHT CALIBRATIONS - MRI RAW IMAGES V1.0

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set contains raw calibration images acquired by the Deep Impact Medium Resolution Visible CCD from 04 October 2007 through 09 January 2008 for the EPOXI...

  13. Why does silane enhance the protective properties of epoxy films?

    Science.gov (United States)

    Wang, Peng; Schaefer, Dale W

    2008-12-02

    Using neutron reflectivity, the protection mechanisms of a novel one-step epoxy-silane coating system were investigated in terms of coating structure and water response behavior. By comparing pure epoxy and epoxy-silane mixtures in various aqueous environments, the effects of the addition of silane were determined. Specifically, a bridged bis-silane coupling agent with six alkoxy moieties and a polysulfur bridge was investigated. The key mechanisms of silane-enhanced protection are (1) the silane is enriched at the substrate-coating interface, forming a hydrophobic dense interfacial layer and good adhesion to the substrate, and (2) the silane serves as a cross-linker, resulting in a denser and less hydrophilic bulk film compared to the neat epoxy. The hydrophobic nature of bis-sulfur silane also increases the overall hydrophobicity of the mixed film.

  14. Exit Presentation: Infrared Thermography on Graphite/Epoxy

    Science.gov (United States)

    Comeaux, Kayla

    2010-01-01

    This slide presentation reports on the internship project that was accomplished during the summer of 2010. The objectives of the project were to: (1) Simulate Flash Thermography on Graphite/Epoxy Flat Bottom hole Specimen and thin void specimens, (2) Obtain Flash Thermography data on Graphite/Epoxy flat bottom hole specimens, (3) Compare experimental results with simulation results, Compare Flat Bottom Hole Simulation with Thin Void Simulation to create a graph to determine size of IR Thermography detected defects

  15. Properties of Graphene Oxide/Epoxy Resin Composites

    OpenAIRE

    Jijun Tang; Haijun Zhou; Yunxia Liang; Xinlan Shi; Xin Yang; Jiaoxia Zhang

    2014-01-01

    The graphene oxide (GO) was obtained by pressurized oxidation method using natural graphite as raw materials. Then the GO/epoxy resin composites were prepared by casting. The mechanical and damping properties of composites were studied. As a result, the impact intensity of GO/epoxy resin composites was prominently improved with the content of the graphene oxide increasing. The glass transition temperature decreased and the damping capacity is improved.

  16. [Preparation and properties of hydroxyapatite/epoxy composite].

    Science.gov (United States)

    Zhao, Junliang; Fu, Tao; Wei, Jianhua; Han, Yong; Xu, Kewei

    2005-04-01

    The hydroxyapatite (HA) powder surface modified with silane coupling agent was used to prepare HA/epoxy composite. It was found that silane has greatly improved the dispersion of HA in epoxy. The composite has good in vitro bioactivity and biocompatibility with 40 wt% HA, and the flexural modulus is close to that of natural bone, but its strength is lower than that of natural bone. So the composite needs further reinforcement in some way or other.

  17. Optical emission behavior and radiation resistance of epoxy resins

    International Nuclear Information System (INIS)

    Kawanishi, Shunichi; Udagawa, Akira; Hagiwara, Miyuki

    1987-11-01

    To make clear a mechanism of radiation resistance of epoxy resin systems, a role of energy trapping site induced in bisphenol A type epoxy resins cured with 4 kinds of aromatic amines (Φ N ) was studied in comparison with the case of aliphatic amine curing system through a measurement of optical emission. In the system of the epoxy resin cured with DETA, the optical emission from an excited state of bisphenol A unit of epoxy resin and a charge transfer complex was observed. On the other hand, the optical emission from Φ N was observed in the aromatic amine curing system. Their excitation spectrum consists of peaks of absorption spectrum of BA and those of Φ N , showing that the excited state of Φ N is formed through the excitation of both BA and Φ N . Therefore, the excited energy of BA transfers to the excited state of Φ N . Emission intensity of Φ N band was 20 ∼ 100 times as large as that of BA. These results indicate that the radiation energy is effectively released as an optical emission from excited state of Φ N in the epoxy resin when cured with aromatic amine. It can be concluded from the above results that aromatic amine hardeners contribute to enhancement of the radiation resistance of epoxy resin by acting as an energy transfer agent. (author)

  18. Microstructure, elastic and electromagnetic properties of epoxy-graphite composites

    Science.gov (United States)

    Bellucci, S.; Micciulla, F.; Levin, V. M.; Petronyuk, Yu. S.; Chernozatonskii, L. A.; Kuzhir, P. P.; Paddubskaya, A. G.; Macutkevic, J.; Pletnev, M. A.; Fierro, V.; Celzard, A.

    2015-06-01

    A set of epoxy resin-based composites filled with 0.25 - 2.0 wt.% of commercially available exfoliated graphite (EG) and thick graphene (TG), prepared by suspending EG particles in cyclohexane, and submitting the suspension to a series of grinding and ultrasonic dispersion steps, was produced. The microstructure of such epoxy-graphite composites has been studied by the impulse acoustic microscopy technique. According to acoustic microscopy data, exfoliated graphite microparticles have been well dispersed in the epoxy matrix. TG nanoflakes demonstrated persistent tendency to clustering and formation of agglomerates. The addition of graphite particles in small amount (0.25 - 2.0 wt.%) did not influence the bulk elastic properties of epoxy-graphite composite materials. Being extremely lightweight, 0.003 g cm-3, EG had a lower percolation threshold than TG, at the level of 1-1.5 wt.% against 2.1-3.2 wt.%, respectively. As a result, epoxy composites filled with 1.0-2.0 wt.% EG provided high electromagnetic (EM) interference shielding both at microwave and THz frequencies. In contrast, no significant influence of TG loading was observed at low weight fraction (up to 2 wt.%) on the EM performance of epoxy composites.

  19. Microstructure, elastic and electromagnetic properties of epoxy-graphite composites

    Directory of Open Access Journals (Sweden)

    S. Bellucci

    2015-06-01

    Full Text Available A set of epoxy resin-based composites filled with 0.25 – 2.0 wt.% of commercially available exfoliated graphite (EG and thick graphene (TG, prepared by suspending EG particles in cyclohexane, and submitting the suspension to a series of grinding and ultrasonic dispersion steps, was produced. The microstructure of such epoxy-graphite composites has been studied by the impulse acoustic microscopy technique. According to acoustic microscopy data, exfoliated graphite microparticles have been well dispersed in the epoxy matrix. TG nanoflakes demonstrated persistent tendency to clustering and formation of agglomerates. The addition of graphite particles in small amount (0.25 – 2.0 wt.% did not influence the bulk elastic properties of epoxy-graphite composite materials. Being extremely lightweight, 0.003 g cm−3, EG had a lower percolation threshold than TG, at the level of 1-1.5 wt.% against 2.1-3.2 wt.%, respectively. As a result, epoxy composites filled with 1.0-2.0 wt.% EG provided high electromagnetic (EM interference shielding both at microwave and THz frequencies. In contrast, no significant influence of TG loading was observed at low weight fraction (up to 2 wt.% on the EM performance of epoxy composites.

  20. Performance of epoxy-nanocomposite under corrosive environment

    Directory of Open Access Journals (Sweden)

    2007-06-01

    Full Text Available Nanocomposite materials consisting of polymeric matrix materials and natural or synthetic layered minerals like clay are currently an expanding field of study because these new materials often exhibit a wide range of improved properties over their unmodified starting polymers. Epoxy/organoclay nanocomposites have been prepared by intercalating epoxy into the organoclay via direct mixing process. The clay exfoliation was monitored by X-ray diffraction (XRD and transmission electron microscopy (TEM. Water diffusion and sulfuric acid corrosion resistance of epoxy-based nanocomposites were evaluated. Diffusion was studied through epoxy samples containing up to 6 phr (parts per hundred resin of an organically treated montmorillonite. The diffusion of the environmental solution was measured by noting the increase in weight of the samples as a function of immersion time in these solutions at 80°C. The effect of the degree of exfoliation of the organoclay on water barrier and corrosion resistance was specifically studied. The data have been compared to those obtained from the neat epoxy resin to evaluate the diffusion properties of the nanocomposites. The flexural strength of the epoxy/organoclay nanocomposites samples made was examined to compare their mechanical performance under corrosive conditions as a function of immersion time and temperature. It was found, that the organoclay was mainly intercalated with some exfoliation and that addition of the organoclay yields better flexural strength retention under immersion into sulfuric acid.

  1. Characterization of Epoxy Composites Reinforced with Wax Encapsulated Microcrystalline Cellulose

    Directory of Open Access Journals (Sweden)

    Yuanfeng Pan

    2016-11-01

    Full Text Available The effect of paraffin wax encapsulated microcrystalline cellulose (EMC particles on the mechanical and physical properties of EMC/epoxy composites were investigated. It was demonstrated that the compatibility between cellulose and epoxy resin could be maintained due to partial encapsulation resulting in an improvement in epoxy composite mechanical properties. This work was unique because it was possible to improve the physical and mechanical properties of the EMC/epoxy composites while encapsulating the microcrystalline cellulose (MCC for a more homogeneous dispersion. The addition of EMC could increase the stiffness of epoxy composites, especially when the composites were wet. The 1% EMC loading with a 1:2 ratio of wax:MCC demonstrated the best reinforcement for both dry and wet properties. The decomposition temperature of epoxy was preserved up to a 5% EMC loading and for different wax:MCC ratios. An increase in wax encapsulated cellulose loading did increase water absorption but overall this absorption was still low (<1% for all composites.

  2. Thermo-curable epoxy systems for nanoimprint lithography

    International Nuclear Information System (INIS)

    Wu, Chun-Chang; Hsu, Steve Lien-Chung

    2010-01-01

    In this work, we have used solvent-free thermo-curable epoxy systems for low-pressure and moderate-temperature nanoimprint lithography (NIL). The curing kinetic parameters and conversion of diglycidyl ether of bisphenol A (DGEBA) resin with different ambient-cure 930 and 954 hardeners were studied by the isothermal DSC technique. They are useful for the study of epoxy resins in the imprinting application. The DGEBA/930 and DGEBA/954 epoxy resists can be imprinted to obtain high-density nano- and micro-scale patterns on a flexible indium tin oxide/poly(ethylene terephthalate) (ITO/PET) substrate. The DGEBA/930 epoxy resin is not only suitable for resist material, but also for plastic mold material. Highly dense nanometer patterns can be successfully imprinted using a UV-curable resist from the DGEBA/930 epoxy mold. Using the replicated DGEBA/930 epoxy mold instead of the expensive master can prevent brittle failure of the silicon molds in the NIL

  3. Adhesion strength improvement of epoxy resin reinforced with nanoelastomeric copolymer

    International Nuclear Information System (INIS)

    Khoee, Sepideh; Hassani, Narges

    2010-01-01

    Research highlights: → Elastomeric nanoparticle (ENP) was prepared via miniemulsion polymerization. → ENP was added to epoxy resin (ER) with different amounts. → The lap shear strength (LSS) of different ENP/ER was measured. → The fractured surfaces were examined by scanning electron microscopy (SEM). - Abstract: Nano-sized copoly(styrene-butylacrylate-ethylenglycoldimethacrylate) (St-BA-EGDMA) particles were added at different contents to improve the toughness of diglycidyl ether of bisphenol A epoxy resin (ER) using piperidine as a curing agent. Transmission electron microscopy (TEM) proved that nanoelastomer was finely dispersed in the epoxy adhesive. To compare the adhesion strength of different adherents utilizing both modified and unmodified epoxy adhesive, the lap shear strength (LSS) test was measured as a function of elastomeric nanoparticles (ENP) amount. Scanning electron microscopy (SEM) and FTIR were used to investigate the interface morphology and chemical composition of adherent and epoxy adhesive. The result indicated that the adhesion strength was increased dramatically by addition of nanoparticles compared with that of pure epoxy adhesive. The highest adhesion strength was obtained with 20 wt% elastomeric nanoparticles. It was found that reinforcement with nanoparticles improved the fracture toughness.

  4. Evaluation of bond strength of various epoxy resin based sealers in oval shaped root canals.

    Science.gov (United States)

    Cakici, Fatih; Cakici, Elif Bahar; Ceyhanli, Kadir Tolga; Celik, Ersan; Kucukekenci, Funda Fundaoglu; Gunseren, Arif Onur

    2016-09-30

    The aim of this study was to evaluate the bond strength of AH plus, Acroseal, and Adseal to the root canal dentin. A total of 36 single-rooted, mandibular premolar teeth were used. Root canal shaping procedures were performed with ProTaper rotary instruments (Dentsply Maillefer) up to size F4. The prepared samples were then randomly assembled into 3 groups (n = 12). For each group, an ultrasonic tip (size 15, 0.02 taper) which was also coated with an epoxy resin based sealer and placed 2 mm shorter than the working length. The sealer was then activated for 10 s. A push-out test was used to measure the bond strength between the root canal dentine and the sealer. Kruskal-Wallis test to evaluate the push-out bond strength of epoxy based sealer (P = 0.05). The failure mode data were statistically analyzed using Pearson's chi square test (P = 0.05). Kruskal-Wallis test indicated that there were no statistically significant difference among the push out bond strength values of 3 mm (p = 0.123) and 6 mm (P = 0.057) for groups, there was statistically significant difference push out bond strength value of 9 mm (P = 0.032). Pearson's chi square test showed statistically significant differences for the failure types among the groups. Various epoxy resin based sealers activated ultrasonically showed similar bond strength in oval shaped root canals. Apical sections for all groups have higher push out bond strength values than middle and coronal sections.

  5. Effects of Nanofillers on the Thermo-Mechanical Properties and Chemical Resistivity of Epoxy Nanocomposites.

    Science.gov (United States)

    Atchudan, Raji; Pandurangan, Arumugam; Joo, Jin

    2015-06-01

    MWCNTs was synthesized using Ni-Cr/MgO by CVD method and were purified. The purified MWCNT was used as a filler material for the fabrication of epoxy nanocomposites. The epoxy nanocomposites with different amount (wt% = 0.5, 1.0, 2.0, 3.0, 4.0 and 5.0) of nanofillers (CB, SiO2 and MWCNTs) were prepared by casting method. The effects of nanofillers on the properties of neat epoxy matrix were well studied. The thermal properties of nanocomposites were studied using DSC, TGA and flame retardant, and also the mechanical properties such as tensile strength, flexural strength, compressive strength, impact strength, determination of hardness and chemical resistance were studied extensively. Based on the experiment's results, 2 wt% MWCNTs loading in epoxy resin showed the highest improvement in tensile strength, as compared to neat epoxy and to other epoxy systems (CB/epoxy, SiO2/epoxy). Improvements in tensile strength, glass transition temperature and decomposition temperature were observed by the addition of MWCNTs. The mechanical properties of the epoxy nanocomposites were improved due to the interfacial bonding between the MWCNTs and epoxy resin. Strain hardening behavior was higher for MWCNT/epoxy nanocomposites compared with CB/epoxy and SiO2/epoxy nanocomposites. The investigation of thermal and mechanical properties reveals that the incorporation of MWCNTs into the epoxy nanocomposites increases its thermal stability to a great extent. Discrete increase of glass transition temperature of nanocomposites is linearly dependent on MWCNTs content. Due to strong interfacial bonding between MWCNTs and epoxy resin, the chemical resistivity of MWCNT/epoxy nanocomposites is superior to neat epoxy and other epoxy systems.

  6. Characteristics of epoxy resin/SiO2 nanocomposite insulation: effects of plasma surface treatment on the nanoparticles.

    Science.gov (United States)

    Yan, Wei; Phung, B T; Han, Zhao Jun; Ostrikov, Kostya

    2013-05-01

    The present study compares the effects of two different material processing techniques on modifying hydrophilic SiO2 nanoparticles. In one method, the nanoparticles undergo plasma treatment by using a custom-developed atmospheric-pressure non-equilibrium plasma reactor. With the other method, they undergo chemical treatment which grafts silane groups onto their surface and turns them into hydrophobic. The treated nanoparticles are then used to synthesize epoxy resin-based nanocomposites for electrical insulation applications. Their characteristics are investigated and compared with the pure epoxy resin and nanocomposite fabricated with unmodified nanofillers counterparts. The dispersion features of the nanoparticles in the epoxy resin matrix are examined through scanning electron microscopy (SEM) images. All samples show evidence that the agglomerations are smaller than 30 nm in their diameters. This indicates good dispersion uniformity. The Weibull plot of breakdown strength and the recorded partial discharge (PD) events of the epoxy resin/plasma-treated hydrophilic SiO2 nanocomposite (ER/PTI) suggest that the plasma-treated specimen yields higher breakdown strength and lower PD magnitude as compared to the untreated ones. In contrast, surprisingly, lower breakdown strength is found for the nanocomposite made by the chemically treated hydrophobic particles, whereas the PD magnitude and PD numbers remain at a similar level as the plasma-treated ones.

  7. Fatigue life extension of epoxy materials using ultrafast epoxy-SbF5 healing system introduced by manual infiltration

    Directory of Open Access Journals (Sweden)

    X. J. Ye

    2015-03-01

    Full Text Available The present paper is devoted to the verification of the capability of epoxy-SbF5 system as a healing chemistry for rapidly retarding and/or arresting fatigue cracks in epoxy materials at room temperature. Owing to the very fast curing speed of epoxy catalyzed by SbF5, epoxy monomer and the hardener (ethanol solution of SbF5–ethanol complex are successively infiltrated into the fracture plane under cyclic loading during the tension-tension fatigue test. As a result, the mechanisms including hydrodynamic pressure crack tip shielding, polymeric wedge and adhesive bonding of the healing agent are revealed. It is found that the healing agent forms solidified wedge at the crack tip within 20 s after start of polymerization of the epoxy monomer, so that the highest healing effect is offered at the moment. The epoxy-SbF5 system proves to be effective in rapidly obstructing fatigue crack propagation (despite that its cured version has lower fracture toughness than the matrix, and satisfies the requirement of constructing fast self-healing polymeric materials.

  8. Design and Analysis of Drive Shaft using Kevlar/Epoxy and Glass/Epoxy as a Composite Material

    Science.gov (United States)

    Karthikeyan, P.; Gobinath, R.; Kumar, L. Ajith; Jenish, D. Xavier

    2017-05-01

    In automobile industry drive shaft is one of the most important components to transmit power form the engine to rear wheel through the differential gear. Generally steel drive shaft is used in automobile industry, nowadays they are more interested to replace steel drive shaft with that of composite drive shaft. The overall objective of this paper is to analyze the composite drive shaft using to find out the best replacement for conventional steel drive shaft. The uses of advanced composite materials such as Kevlar, Graphite, Carbon and Glass with proper resins ware resulted in remarkable achievements in automobile industry because of its greater specific strength and specific modulus, improved fatigue and corrosion resistances and reduction in energy requirements due to reduction in weight as compared to steel shaft. This paper is to presents, the modeling and analysis of drive shaft using Kevlar/Epoxy and Glass/Epoxy as a composite material and to find best replacement for conventional steel drive shafts with an Kevlar/epoxy or Glass/Epoxy resin composite drive shaft. Modeling is done using CATIA software and Analysis is carried out by using ANSYS 10.0 software for easy understanding. The composite drive shaft reduces the weight by 81.67 % for Kevlar/Epoxy and 72.66% for Glass/Epoxy when compared with conventional steel drive shaft.

  9. Poly(arylene ether-co-imidazole)s as toughness modifiers for epoxy resins

    Science.gov (United States)

    Mcdaniel, Patricia D. (Inventor); Connell, John W. (Inventor)

    1994-01-01

    A toughened epoxy was prepared by reacting an epoxy resin with a poly(arylene ether-co-imidazole)s (PAEI). The epoxy resin comprises N,N,N',N'tetraglycidyl-4,4'- methylenebisbenzenamine and 4-aminophenyl sulfone. The PAEI was prepared by reacting an aromatic bisphenol, a bisphenol imidazole, and an activated aromatic dihalide or dinitro compound in the presence of potassium carbonate in a polar aprotic solvent at an elevated temperature. The epoxies which were modified with these particular PAEI's showed a significant increase in toughness with only a 10 weight percent loading of the PAEI into the epoxy. These toughened epoxies were used to prepare composites and molded parts.

  10. Research on blend system of epoxy resin cured by electron beam

    International Nuclear Information System (INIS)

    Sui Gang; Zhong Weihong; Zhang Zuoguang; Mao Shuli

    2000-01-01

    Electron beam curing of various blends of epoxy resin was studied. Radiation effect of epoxy resin systems of 828, 648 and 207, and their blends was compared. The effect of resin compounding ratio and radiation dose on blends of epoxy resin 828 and 648 systems was analyzed. The performance of the blend with different ratio of epoxy resin 207 and 648 was also studied. The results of study show that radiation effect of epoxy resin is associated with its chemical constitution, steric effect, and crystallinity. The mixing of various epoxy resin can improve radiation curing effect of system, reduce required radiation dose, and enhance performance of radiation product

  11. Experimental design applied optimization of a state in epoxy clay dispersion; Planejamento de experimentos aplicado a otimizacao do estado de dispersao de argilas em epoxi

    Energy Technology Data Exchange (ETDEWEB)

    Paz, Juliana D' Avila; Bertholdi, Jonas; Folgueras, Marilena Valadares; Pezin, Sergio Henrique; Coelho, Luiz Antonio Ferreira, E-mail: julianadpaz@yahoo.com.b [Universidade do Estado de Santa Catarina (UDESC), Joinville, SC (Brazil). Centro de Ciencias Tecnologicas

    2010-07-01

    This paper presents some analysis showed that the exfoliation / intercalation of a montmorillonite clay in epoxy resin such as viscosity, X-ray diffraction (XRD), scanning electron microscopy (SEM) and thermogravimetry (TG). Increasing the viscosity of epoxy resin diglycidyl ether bisphenol A with the addition of clay associated with the sonification system at the time of dispersion is a good indication of exfoliation. The X-ray diffraction already cured composite shows a decrease of crystallinity of clay and EDS microanalysis of SEM, non-uniform dispersion of clay in epoxy resin. Thermal analysis TG composite clay / epoxy shows an increase in thermal stability relative to pure epoxy. (author)

  12. Synthesis and characterizations of melamine-based epoxy resins.

    Science.gov (United States)

    Ricciotti, Laura; Roviello, Giuseppina; Tarallo, Oreste; Borbone, Fabio; Ferone, Claudio; Colangelo, Francesco; Catauro, Michelina; Cioffi, Raffaele

    2013-09-05

    A new, easy and cost-effective synthetic procedure for the preparation of thermosetting melamine-based epoxy resins is reported. By this innovative synthetic method, different kinds of resins can be obtained just by mixing the reagents in the presence of a catalyst without solvent and with mild curing conditions. Two types of resins were synthesized using melamine and a glycidyl derivative (resins I) or by adding a silane derivative (resin II). The resins were characterized by means of chemical-physical and thermal techniques. Experimental results show that all the prepared resins have a good thermal stability, but differ for their mechanical properties: resin I exhibits remarkable stiffness with a storage modulus value up to 830 MPa at room temperature, while lower storage moduli were found for resin II, indicating that the presence of silane groups could enhance the flexibility of these materials. The resins show a pot life higher than 30 min, which makes these resins good candidates for practical applications. The functionalization with silane terminations can be exploited in the formulation of hybrid organic-inorganic composite materials.

  13. Viscoelastic properties of graphene-based epoxy resins

    Science.gov (United States)

    Nobile, Maria Rossella; Fierro, Annalisa; Rosolia, Salvatore; Raimondo, Marialuigia; Lafdi, Khalid; Guadagno, Liberata

    2015-12-01

    In this paper the viscoelastic properties of an epoxy resin filled with graphene-based nanoparticles have been investigated in the liquid state, before curing, by means of a rotational rheometer equipped with a parallel plate geometry. Exfoliated graphite was prepared using traditional acid intercalation followed by a sudden treatment at high temperature (900°C). The percentage of exfoliated graphite was found to be 56%. The epoxy matrix was prepared by mixing a tetrafunctional precursor with a reactive diluent which produces a significant decrease in the viscosity of the epoxy precursor so that the dispersion step of nanofillers in the matrix can easily occur. The hardener agent, the 4,4-diaminodiphenyl sulfone (DDS), was added at a stoichiometric concentration with respect to all the epoxy rings. The inclusion of the partially exfoliated graphite (pEG) in the formulated epoxy mixture significantly modifies the rheological behaviour of the mixture itself. The epoxy mixture, indeed, shows a Newtonian behaviour while, at 3 wt % pEG content, the complex viscosity of the nanocomposite clearly shows a shear thinning behaviour with η* values much higher at the lower frequencies. The increase in complex viscosity with the increasing of the partially exfoliated graphite content was mostly caused by a dramatic increase in the storage modulus. All the graphene-based epoxy mixtures were cured by a two-stage curing cycles: a first isothermal stage was carried out at the lower temperature of 125°C for 1 hour while the second isothermal stage was performed at the higher temperature of 200°C for 3 hours. The mechanical properties of the cured nanocomposites show high values in the storage modulus and glass transition temperature.

  14. Shape memory polymers from benzoxazine-modified epoxy

    Science.gov (United States)

    Rimdusit, Sarawut; Lohwerathama, Montha; Hemvichian, Kasinee; Kasemsiri, Pornnapa; Dueramae, Isala

    2013-07-01

    Novel shape memory polymers (SMPs) were prepared from benzoxazine-modified epoxy resin. Specimens consisting of aromatic epoxy (E), aliphatic epoxy (N), Jeffamine D230 (D) and BA-a benzoxazine monomer (B) were evaluated. The mole ratio of D/B was used as a mixed curing agent for an epoxy system with a fixed E/N. The effects of BA-a content on the thermal, mechanical and shape memory properties of epoxy-based shape memory polymers (SMPs) were investigated by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), flexural test and shape recovery test. The results revealed that the obtained SMPs exhibited a higher flexural strength and flexural modulus than those of the unmodified epoxy-based SMP at room temperature and at 20 ° C above glass transition temperature (Tg). The presence of 1 mol BA-a as a curing agent provided the specimen with the highest Tg, i.e. about 72 ° C higher than that of epoxy-based SMP cured by Jeffamine D230. All SMP samples needed only a few minutes to fully recover to their original shape. The samples exhibited high shape fixity (98-99%) and shape recovery ratio (90-100%). In addition, the recovery stress values increased with increasing BA-a mole ratio from 20 to 38 kPa, when BA-a up to 1 mol ratio was added. All of the SMP samples exhibited only minimum change in their flexural strength at the end of a 100 recovery cycles test.

  15. Physical, structural and thermomechanical properties of oil palm nano filler/kenaf/epoxy hybrid nanocomposites

    Energy Technology Data Exchange (ETDEWEB)

    Saba, N., E-mail: naheedchem@gmail.com [Laboratory of Biocomposite Technology, Institute of Tropical Forestry and Forest Products(INTROP), Universiti Putra Malaysia, 43400 UPM Serdang, Selangor (Malaysia); Paridah, M.T. [Laboratory of Biocomposite Technology, Institute of Tropical Forestry and Forest Products(INTROP), Universiti Putra Malaysia, 43400 UPM Serdang, Selangor (Malaysia); Abdan, K. [Department of Biological and Agricultural Engineering, Faculty of Engineering, Universiti Putra Malaysia, 43400 UPM Serdang Selangor (Malaysia); Ibrahim, N.A. [Department of Chemistry, Faculty of Science, Universiti Putra Malaysia, 43400 UPM Serdang, Selangor (Malaysia)

    2016-12-01

    The present research study deals with the fabrication of kenaf/epoxy hybrid nanocomposites by the incorporation of oil palm nano filler, montmorillonite (MMT) and organically modified montmorillonite (OMMT) at 3% loading, through hand lay-up technique. Effect of adding different nano fillers on the physical (density), structural [X-ray diffraction (XRD)] and thermomechanical analysis (TMA) of kenaf/epoxy composites were carried out. Density results revealed that the incorporation of nano filler in the kenaf/epoxy composites increases the density which in turn increases the hardness of the hybrid nanocomposites. XRD analysis confirmed the presence of nano fillers in the structure of their respective fabricated hybrid nanocomposites. All hybrid nanocomposites displayed lower coefficient of thermal expansion (CTE) with respect to kenaf/epoxy composites. Overall results predicted that the properties improvement in nano OPEFB/kenaf/epoxy was quite comparable to MMT/kenaf/epoxy but relatively lesser to OMMT/kenaf/epoxy hybrid nanocomposites and higher with respect to kenaf/epoxy composites. The improvement ascribed due to improved interfacial bonding or cross linking between kenaf fibers and epoxy matrix by addition of nano filler. - Highlights: • Nano OPEFB/kenaf/epoxy hybrid nanocomposites were fabricated by hand lay-up. • Effect of nano OPEFB on density & structure of kenaf/epoxy were investigated. • Thermal expansion coefficients of kenaf/epoxy and hybrid nanocomposites evaluated. • Comparative studies were made with MMT and OMMT kenaf/epoxy hybrid nanocomposites.

  16. Physical, structural and thermomechanical properties of oil palm nano filler/kenaf/epoxy hybrid nanocomposites

    International Nuclear Information System (INIS)

    Saba, N.; Paridah, M.T.; Abdan, K.; Ibrahim, N.A.

    2016-01-01

    The present research study deals with the fabrication of kenaf/epoxy hybrid nanocomposites by the incorporation of oil palm nano filler, montmorillonite (MMT) and organically modified montmorillonite (OMMT) at 3% loading, through hand lay-up technique. Effect of adding different nano fillers on the physical (density), structural [X-ray diffraction (XRD)] and thermomechanical analysis (TMA) of kenaf/epoxy composites were carried out. Density results revealed that the incorporation of nano filler in the kenaf/epoxy composites increases the density which in turn increases the hardness of the hybrid nanocomposites. XRD analysis confirmed the presence of nano fillers in the structure of their respective fabricated hybrid nanocomposites. All hybrid nanocomposites displayed lower coefficient of thermal expansion (CTE) with respect to kenaf/epoxy composites. Overall results predicted that the properties improvement in nano OPEFB/kenaf/epoxy was quite comparable to MMT/kenaf/epoxy but relatively lesser to OMMT/kenaf/epoxy hybrid nanocomposites and higher with respect to kenaf/epoxy composites. The improvement ascribed due to improved interfacial bonding or cross linking between kenaf fibers and epoxy matrix by addition of nano filler. - Highlights: • Nano OPEFB/kenaf/epoxy hybrid nanocomposites were fabricated by hand lay-up. • Effect of nano OPEFB on density & structure of kenaf/epoxy were investigated. • Thermal expansion coefficients of kenaf/epoxy and hybrid nanocomposites evaluated. • Comparative studies were made with MMT and OMMT kenaf/epoxy hybrid nanocomposites.

  17. Study of the reaction between polyethylene glycol and epoxy resins using N,N-dimethylbenzylamine as catalyst;Estudo da reacao entre polietileno glicol e resinas epoxi usando N,N-dimetilbenzilamina como catalisador

    Energy Technology Data Exchange (ETDEWEB)

    Zacharuk, Mario; Coelho, Luiz A.F.; Pezzin, Sergio H., E-mail: pezzin@joinville.udesc.b [Universidade do Estado de Santa Catarina (UDESC), Joinville (Brazil). Centro de Ciencias Tecnologicas; Becker, Daniela [Sociedade Educacional de Santa Catarina (SOCIESC), Joinville (Brazil). Inst. Superior Tupy

    2009-07-01

    In this work the use of N,N-dimethylbenzylamine as a catalyst of the reaction of polyethylene glycol (PEG) and epoxy resin (DGEBA) was studied. The reaction products were evaluated by infra-red spectroscopy (FTIR), nuclear magnetic resonance spectroscopy (NMR) and viscosity measurements. Samples cured with a polyamine-based hardener were also submitted to tensile tests and differential scanning calorimetry (DSC). The results of the viscosity analyses, FTIR and RMN ({sup 1}H) had confirmed the occurrence of the reaction between DGEBA epoxy groups and PEG hydroxyl groups in the presence of N, N-dimethylbenzylamine as catalyst, at 100 deg C. DSC analyses and tensile tests of cured systems showed that the reaction of DGEBA with PEG leads to a reduction of the Tg, generating a more flexible material. (author)

  18. Epoxy nanocomposites based on high temperature pyridinium-modified clays.

    Science.gov (United States)

    Zhang, Qingxin; Naito, Kimiyoshi; Qi, Ben; Kagawa, Yutaka

    2009-01-01

    Polymer/clay nanocomposites are generally fabricated by thermal curing or melt compounding at elevated temperatures, however the thermal stability of common alkyl ammonium treated clays is poor and decomposition occurs inevitably during high temperature processing. In this study, we modified clays with an aromatic pyridinium salt. Thermogravimetric analysis (TGA) showed that the onset degradation temperature (Td(onset)) and maximum decomposition temperature (Td(max)) of the pyridinium treatment clays was up to 310 and 457 degrees C respectively implying high thermal stability. The thermal decomposition behaviour of the pyridinium modified clays was discussed. A series of epoxy/clay nanocomposites were synthesized using a diglycidyl ether of bisphenol A (DGEBA) epoxy and diethyltoluene diamine (DETDA). The morphology of epoxy/clay nanocomposites was characterized with wide angle X-ray diffraction (WAXD) and transmission electron microscope (TEM), and intercalated structures were observed. The storage modulus of epoxy was increased but glass transition temperature was decreased with clay incorporation. The effects of clays on glass transition temperature (Tg) of epoxy were also discussed.

  19. Fabrication and characterisation of graphene oxide-epoxy nanocomposite

    Science.gov (United States)

    Galpaya, Dilini; Wang, Mingchao; Yan, Cheng; Liu, Meinan; Motta, Nunzio; Waclawik, Eric

    2013-08-01

    Adequate amount of graphene oxide (GO) was firstly prepared by oxidation of graphite and GO/epoxy nanocomposites were subsequently prepared by typical solution mixing technique. X-ray diffraction (XRD) pattern, X-ray photoelectron (XPS), Raman and Fourier transform infrared (FTIR) spectroscopy indicated the successful preparation of GO. Scanning electron microscopy (SEM) and Transmission electron microscopy (TEM) images of the graphite oxide showed that they consist of a large amount of graphene oxide platelets with a curled morphology containing of a thin wrinkled sheet like structure. AFM image of the exfoliated GO signified that the average thickness of GO sheets is ~1.0 nm which is very similar to GO monolayer. Mechanical properties of as prepared GO/epoxy nanocomposites were investigated. Significant improvements in both Young's modulus and tensile strength were observed for the nanocomposites at very low level of GO loading. The Young's modulus of the nanocomposites containing 0.5 wt% GO was 1.72 GPa, which was 35 % higher than that of the pure epoxy resin (1.28 GPa). The effective reinforcement of the GO based epoxy nanocomposites can be attributed to the good dispersion and the strong interfacial interactions between the GO sheets and the epoxy resin matrices.

  20. Epoxy resin/carbon black composites below the percolation threshold.

    Science.gov (United States)

    Macutkevic, J; Kuzhir, P; Paddubskaya, A; Maksimenko, S; Banys, J; Celzard, A; Fierro, V; Stefanutti, E; Cataldo, A; Micciulla, F; Bellucci, S

    2013-08-01

    A set of epoxy resin composites filled with 0.25-2.0 wt.% of commercially available ENSACO carbon black (CB) of high and low surface area (CBH and CBL respectively) has been produced. The results of broadband dielectric spectroscopy of manufactured CB/epoxy below the percolation threshold in broad temperature (200 K to 450 K) and frequency (20 Hz to 1 MHz) ranges are reported. The dielectric properties of composites below the percolation threshold are mostly determined by alpha relaxation in pure polymer matrix. The glass transition temperature for CB/epoxy decreases in comparison with neat epoxy resin due to the extra free volume at the polymer-filler interface. At room temperature, the dielectric permittivity is higher for epoxy loaded with CBH additives. In contrast, at high temperature, the electrical conductivity was found to be higher for composites with CBL embedded. The established influence of the CB surface area on the broadband dielectric characteristics can be exploited for the production of effective low-cost antistatic paints and coatings working at different temperatures.

  1. Liquid crystalline epoxy nanocomposite material for dental application.

    Science.gov (United States)

    Tai, Yun-Yuan; Hsu, Sheng-Hao; Chen, Rung-Shu; Su, Wei-Fang; Chen, Min-Huey

    2015-01-01

    Novel liquid crystalline epoxy nanocomposites, which exhibit reduced polymerization shrinkage and effectively bond to tooth structures, can be applied in esthetic dentistry, including core and post systems, direct and indirect restorations, and dental brackets. The purposes of this study were to investigate the properties of liquid crystalline epoxy nanocomposites including biocompatibility, microhardness, and frictional forces of bracket-like blocks with different filler contents for further clinical applications. In this study, we evaluated liquid crystalline epoxy nanocomposite materials that exhibited various filler contents, by assessing their cell activity performance using a 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide assay and their microhardness with or without thermocycling. We also evaluated the frictional force between bracket-like duplicates and commercially available esthetic bracket systems using Instron 5566. The liquid crystalline epoxy nanocomposite materials showed good biocompatibility. The materials having high filler content demonstrated greater microhardness compared with commercially available bracket materials, before and after the thermocycling treatment. Thus, manufacturing processes are important to reduce frictional force experienced by orthodontic brackets. The microhardness of the bracket-like blocks made by our new material is superior to the commercially available brackets, even after thermocycling. Our results indicate that the evaluated liquid crystalline epoxy nanocomposite materials are of an appropriate quality for application in dental core and post systems and in various restorations. By applying technology to refine manufacturing processes, these new materials could also be used to fabricate esthetic brackets for orthodontic treatment. Copyright © 2014. Published by Elsevier B.V.

  2. Fabrication and characterization of TiO2-epoxy nanocomposite

    International Nuclear Information System (INIS)

    Chatterjee, Amit; Islam, Muhammad S.

    2008-01-01

    A systematic study has been conducted to investigate the matrix properties by introducing nanosize TiO 2 (5-40 nm, 0.5-2% by weight) fillers into an epoxy resin. Ultrasonic mixing process, via sonic cavitations, was employed to disperse the particles into the resin system. The thermal, mechanical, morphology and the viscoelastic properties of the nanocomposite and the neat resin were measured with TGA, DMA, TEM and Instron. The nano-particles are dispersed evenly throughout the entire volume of the resin. The nanofiller infusion improves the thermal, mechanical and viscoelastic properties of the epoxy resin. The nanocomposite shows increase in storage modulus, glass transition temperature, tensile modulus, flexural modulus and short beam shear strength from neat epoxy resin. The mechanical performance and thermal stability of the epoxy nanocomposites are depending on with the dispersion state of the TiO 2 in the epoxy matrix and are correlated with loading (0.0015-0.006% by volume). In addition, the nanocomposite shows enhanced flexural strength. Several reasons to explain these effects in terms of reinforcing mechanisms were discussed

  3. Fiber-Reinforced Reactive Nano-Epoxy Composites

    Science.gov (United States)

    Zhong, Wei-Hong

    2011-01-01

    An ultra-high-molecular-weight polyethylene/ matrix interface based on the fabrication of a reactive nano-epoxy matrix with lower surface energy has been improved. Enhanced mechanical properties versus pure epoxy on a three-point bend test include: strength (25 percent), modulus (20 percent), and toughness (30 percent). Increased thermal properties include higher Tg (glass transition temperature) and stable CTE (coefficient of thermal expansion). Improved processability for manufacturing composites includes faster wetting rates on macro-fiber surfaces, lower viscosity, better resin infusion rates, and improved rheological properties. Improved interfacial adhesion properties with Spectra fibers by pullout tests include initial debonding force of 35 percent, a maximum pullout force of 25 percent, and energy to debond at 65 percent. Improved mechanical properties of Spectra fiber composites (tensile) aging resistance properties include hygrothermal effects. With this innovation, high-performance composites have been created, including carbon fibers/nano-epoxy, glass fibers/nano-epoxy, aramid fibers/ nano-epoxy, and ultra-high-molecularweight polyethylene fiber (UHMWPE).

  4. Void-free epoxy castings for cryogenic insulators and seals

    International Nuclear Information System (INIS)

    Quirk, J.F.

    1983-01-01

    The design of the Westinghouse Magnet for the Oak Ridge National Laboratory's Large Coil Program (LCP) incorporates a main lead bushing which transmits heat-leak loads by conduction to the supercritical helium stream. The bushing, which consists of epoxy resin cast about a copper conductor, must be electrically insulated, vacuum tight and be capable of withstanding the stresses encountered in cryognic service. The seal design of the bushing is especially important; leakage from either the helium system or the external environment into the vacuum will cause the magnet to quench. Additionally, the epoxy-resin casting must resist mechanical loads caused by the weight of leads attached to the bushing and thermal stresses transmitted to the epoxy via the conductor. The epoxy resin is cast about the conductor in such a way as to provide the required vacuum tight seal. The technique by which this is accomplished is reviewed. Equally important is the elimination of voids in the epoxy which will act as stress-concentrating discontinuities during cooling to or warming from 4K. The types of voids that could be expected and their causes are described. The paper reviews techniques employed to eliminate voids within the cast-resin portion of the bushing

  5. Evaluation of Carbon Composite Overwrap Pressure Vessels Fabricated Using Ionic Liquid Epoxies

    Data.gov (United States)

    National Aeronautics and Space Administration — In terms of "Innovation" this is a unique epoxy with unique properties, and NASA co-holds the patent. This epoxy is being exclusively formulated for cryogenic use....

  6. Mechanical properties of uniaxial natural fabric Grewia tilifolia reinforced epoxy based composites: Effects of chemical treatment

    CSIR Research Space (South Africa)

    Jayaramudu, J

    2014-07-01

    Full Text Available The effects of chemical treatment on the mechanical, morphological, and chemical resistance properties of uniaxial natural fabrics, Grewia tilifolia/epoxy composites, were studied. In order to enhance the interfacial bonding between the epoxy matrix...

  7. UDM enhanced physical and mechanical properties through the formation of nanocavities in an epoxy matrix.

    Science.gov (United States)

    Kumar, Kaushal; Kumar, Arun; Ghosh, P K

    2018-01-01

    The matrix modification of relatively low viscous epoxy based polymer treated under ultrasonic mixing (UM) and ultrasonic mixing with simultaneous stirring by a rotating impeller, referred to as ultrasonic dual mixing (UDM), and the effect of processing techniques has been investigated in terms of the formation of nanocavities in the epoxy matrix. Nanocavities of size 42±8nm have been formed uniformly in the epoxy matrix by UDM. The effect of a change in matrix morphology on the viscoelastic, tensile and thermal properties of the cured epoxy resin has been studied. The UDM processed cured epoxy matrix showed 18.26% and 88.34% improvement in tensile strength and toughness as compared to unprocessed epoxy. Thermal gravimetric analysis (TGA) of UDM processed epoxy showed significant enhancement in the thermal stability of the epoxy matrix. Copyright © 2017 Elsevier B.V. All rights reserved.

  8. E-Beam-Cured Layered-Silicate and Spherical Silica Epoxy Nanocomposites (Preprint)

    National Research Council Canada - National Science Library

    Chen, Chenggang; Anderson, David P

    2007-01-01

    .... The nanofillers can be two dimensional (layered-silicate) and zero dimensional (spherical silica). Both the spherical silica epoxy nanocomposite and the layered-silicate epoxy nanocomposite can be cured to a high degree of curing...

  9. The evaluation of epoxy thermoplastic pavement marking material in Virginia : the application : interim report.

    Science.gov (United States)

    1983-01-01

    Epoxy Thermoplastic (ETP) is a recently developed epoxy-resin-based thermoplastic pavement marking material being promoted by the Federal Highway Administration as a possible substitute for conventional traffic paints and thermoplastics. Its reported...

  10. Toughening of carbon fiber-reinforced epoxy polymer composites via copolymers and graphene nano-platelets

    Science.gov (United States)

    Downey, Markus A.

    Carbon fiber-reinforced epoxy composites currently play a significant role in many different industries. Due to their high cross-link density, aromatic epoxy polymers used as the matrix in composite materials are very strong and stiff however they lack toughness. This dissertation investigates three areas of the carbon fiber-reinforced composite, which have the potential to increase toughness: the carbon fiber surface; the fiber/matrix interphase; and the matrix material. Approaches to improving each area are presented which lead to enhancing the overall composite toughness without reducing other composite mechanical properties. The toughening of the base matrix material, DGEBA/mPDA, was accomplished by two methods: first, using low concentrations of aliphatic copolymers to enhance energy absorption and second by adding graphene nano-platelets (GnP) to act as crack deflection agents. 1wt% copolymer concentration was determined to substantially increase the notched Izod impact strength without reducing other static-mechanical properties. Toughening of DGEBA/mPDA using 3wt% GnP was found to be dependent on the aspect ratio of GnP and treatment of GnP with tetraethylenepentamine (TEPA). GnP C750 enhanced flexural properties but not fracture toughness because the small aspect ratio cannot effectively deflect cracks. TEPA-grafting enhanced GnP/matrix bonding. Larger aspect ratio GnP M5 and M25 showed significant increases in fracture toughness due to better crack deflection but also decreased flexural strength based on limited GnP/matrix bonding. TEPA-grafting mitigated some of the flexural strength reductions for GnP M5, due to enhanced GnP/matrix adhesion. In the high-fiber volume fraction composite, the fiber/matrix bonding was enhanced with UV-ozone surface treatment by reducing a weak fiber surface boundary layer and increasing the concentration of reactive oxygen groups on the fiber surface. Further increases in Mode I fracture toughness were seen with the

  11. Study of the reaction between polyethylene glycol and epoxy resins using N,N-dimethylbenzylamine as catalyst

    International Nuclear Information System (INIS)

    Zacharuk, Mario; Coelho, Luiz A.F.; Pezzin, Sergio H.; Becker, Daniela

    2009-01-01

    In this work the use of N,N-dimethylbenzylamine as a catalyst of the reaction of polyethylene glycol (PEG) and epoxy resin (DGEBA) was studied. The reaction products were evaluated by infra-red spectroscopy (FTIR), nuclear magnetic resonance spectroscopy (NMR) and viscosity measurements. Samples cured with a polyamine-based hardener were also submitted to tensile tests and differential scanning calorimetry (DSC). The results of the viscosity analyses, FTIR and RMN ( 1 H) had confirmed the occurrence of the reaction between DGEBA epoxy groups and PEG hydroxyl groups in the presence of N, N-dimethylbenzylamine as catalyst, at 100 deg C. DSC analyses and tensile tests of cured systems showed that the reaction of DGEBA with PEG leads to a reduction of the Tg, generating a more flexible material. (author)

  12. Analogues of the epoxy resin monomer diglycidyl ether of bisphenol F: effects on contact allergenic potency and cytotoxicity.

    Science.gov (United States)

    O'Boyle, Niamh M; Delaine, Tamara; Luthman, Kristina; Natsch, Andreas; Karlberg, Ann-Therese

    2012-11-19

    Diglycidyl ethers of bisphenol A (DGEBA) and bisphenol F (DGEBF) are widely used as components in epoxy resin thermosetting products. They are known to cause occupational and nonoccupational allergic contact dermatitis. The aim of this study is to investigate analogues of DGEBF with regard to contact allergy and cytotoxicity. A comprehensive knowledge of the structural features that contribute to the allergenic and cytotoxic effects of DGEBF will guide the development of future novel epoxy resin systems with reduced health hazards for those coming into contact with them. It was found that the allergenic effects of DGEBF were dependent on its terminal epoxide groups. In contrast, it was found that the cytotoxicity in monolayer cell culture was dependent not only on the presence of epoxide groups but also on other structural features.

  13. Comparison of the immunolabeling of heated and deplasticized epoxy sections on the electron microscopical level.

    Science.gov (United States)

    Brorson, S H

    1999-08-01

    The purpose of this study was to compare the yield of immunogold labeling of heated epoxy sections with the yield of labeling of deplasticized epoxy sections, and to compare the immunolabeling of deplasticized high-accelerator epoxy sections and deplasticized low-accelerator epoxy sections. Renal swine tissue and human thyroid tissue were embedded in both high- and low-accelerator epoxy resin and also in LR-White resin. Immunogold labeling was performed on deplasticized (ethoxide-treated), heated and non-treated ultrathin sections from these specimens. The renal tissue was immunolabeled with anti-IgG, and the thyroid tissue was immunolabeled with anti-thyroglobulin. The ethoxide treatment of the epoxy sections induced complete deplasticizing. The immunogold labeling with anti-IgG on deplasticized epoxy sections of renal tissue demonstrated significantly more intense immunolabeling of immune complex deposits than the corresponding epoxy sections which were exposed to heat in citrate buffer. The results for labeling areas of thyroglobulin substance with anti-thyroglobulin showed no significant differences between deplasticized and heated epoxy sections, probably because the sodium ethoxide partly destroys the antigenicity. Deplasticized high-accelerator epoxy sections showed significantly higher yield of immunolabeling than deplasticized low-accelerator epoxy sections and LR-White sections both for anti-IgG and anti-thyroglobulin. This can be explained by the reduced tendency for the knife to cleave proteins when cutting high-accelerator epoxy sections. High-accelerator epoxy sections which were exposed to heat in citrate buffer were more intensely immunolabeled than similarly treated low-accelerator epoxy sections, in agreement with previous results. The ultrastructural preservation of the tissues of deplasticized epoxy sections was inferior compared with the other sections. This study shows that the choice between deplasticizing technique or heating of epoxy

  14. Single-Lap-Joint Screening of Hysol EA 9309NA Epoxy Adhesive

    Science.gov (United States)

    2017-05-01

    upon the second heating cycle in the DMA due to additional postcuring of residual unreacted epoxy and curing agent. While the elevated test temperature... epoxy resin high temperature application. Warrendale (PA): SAE International; 2014. eAMS3695/1. Adhesive film, epoxy -base, high durability for 95 °C...200 °F) service. Warrendale (PA): SAE International; 2014. fAMS3695/3. Adhesive film, epoxy -base, high durability for 175 °C (350 °F) service

  15. PREPARATION, CHARACTERIZATION AND THERMAL BEHAVIOR OF ALKYL SUBSTITUTED PHENOLIC EPOXY RESIN

    OpenAIRE

    Jyoti Chaudhary*, Supriya Dadhich, Giriraj Tailor

    2017-01-01

    The present article deals with the synthesis of phenolic epoxy resin by the reaction of phenolic resin and epichlorohydrin. The synthesis of phenolic resin was carried out by using p-ethylphenol, formaldehyde and naphthol. The structures of phenolic and epoxy resins were confirmed by spectroscopic analysis. The synthesized epoxy resin showed solubility in polar solvents like DMF, dioxane, acetone, DMSO, THF, ethyl acetate, and chloroform. Thermal characterization of epoxy resin was monitored ...

  16. Experimental Investigation of Mechanical Properties for Tamarind Shell Particles as Filler in Epoxy Composite

    OpenAIRE

    Srinivas K. R.

    2017-01-01

    This paper explores the potential of tamarind shell particles as a filler in epoxy composites. The tamarind shell particles reinforced epoxy composites plates were prepared by varying both tamarind shell particle and epoxy volume percentage. The mechanical properties such as tensile strength, deflection, impact, hardness and specific gravity are evaluated for different composition of composite plates.This paper explores the potential of tamarind shell particles as a filler in epoxy composites...

  17. Epoxy – the hub for the most versatile polymer with exceptional combination of superlative features

    OpenAIRE

    Inam, Fawad

    2014-01-01

    Epoxy resins and epoxy based materials have experienced significant advancement since their beginning in 1936, when Dr. Castan of Switzerland and Dr. Greenlee of USA succeeded in synthesizing the very first bisphenol-A-based epoxy resins. Whether it is the new carbon fiber composite of Boeing’s Dreamliner or the thin set terrazzo flooring, epoxy has always been the ideal choice because of its superlative properties and unique chemical composition. Belonging to thermoset family, it is certainl...

  18. Multiple welding of long fiber epoxy vitrimer composites.

    Science.gov (United States)

    Chabert, Erwan; Vial, Jérôme; Cauchois, Jean-Pierre; Mihaluta, Marius; Tournilhac, François

    2016-05-25

    Vitrimers appear as a new class of polymers that exhibit mechanical strength and are insoluble even at high temperatures, like thermosets, and yet, like thermoplastics, they are heat processable, recyclable and weldable. The question arises whether this welding property is maintained in composite materials made of more than 50 vol% of reinforcing fibers. In this paper, we quantitatively analyze the bond strength of epoxy vitrimer-based composite plates made by resin transfer molding and compare them to their non-vitrimer counterparts made of a standard thermoset epoxy. It is demonstrated that only epoxy vitrimer samples show substantial bond strength and the ability to be repeatedly welded thanks to the exchange reactions, which promote improved surface conformity and chemical bonding between the adherands at the joint interface. This opens the way towards joining composite parts without adhesives nor mechanical fasteners.

  19. Thermal Measurements on Polymeric Epoxy-Expandable Graphite Material

    Directory of Open Access Journals (Sweden)

    Joseph Asante

    2016-01-01

    Full Text Available Combustion measurements, such as heat release rate, critical flux, time-to-ignition, ignition temperature, thermal inertia, and kinematics—activation energy as well as preexponential factor—on epoxy polymer (Prime™ 20LV with expandable graphite (EG inorganic filler of different weight percentage composites, are conducted using the Dual Cone Calorimeter, the thermogravimetric analysis (TGA, and Linseis (Germany THB100 Transient Hot Bridge thermal conductivity analyser. The results indicate that increasing the amount of EG in polymer composite leads to reduction in the critical flux, the time-to-ignition, the ignition temperature, the thermal inertia, the average thermal conductivity, and the activation energy (from 159.1 ± 2.3 to 145.9 ± 3.1 kJ/mol for neat epoxy to 3 wt.% EG-epoxy of the composite samples. There is, however, an increase in the heat of gasification with increasing EG content.

  20. Thermal and microestructural characterization of epoxy-infiltrated hydroxyapatite composite

    Directory of Open Access Journals (Sweden)

    Pedro Barrionuevo Roese

    2009-03-01

    Full Text Available In this work, hydroxyapatite (HAp obtained from the deorganification of bovine bones using hot NaOH solution was used to synthesize a HAp/epoxy infiltrated composite. Infiltration was carried out by vacuum assisted immersion in hot epoxy resin. The resulting composite was characterized regarding polymer content, morphological aspects and flexural strength. The infiltration method used resulted in thorough infiltration of the HAp but some residual porosity remained. Although the epoxy resin showed good interaction with the HAp, high polymer content was achieved and the flexural strength of the composite was higher than that of the original resin or the HAp, composite strength was lower than that of the human cortical bone.

  1. On sample preparation and dielectric breakdown in nanostructured epoxy resins

    Energy Technology Data Exchange (ETDEWEB)

    Reading, M; Xu, Z; Lewin, P L; Vaughan, A S, E-mail: asv@ecs.soton.ac.uk [Tony Davies High Voltage Laboratory, University of Southampton (United Kingdom)

    2011-08-12

    There are many methods available to achieve a good dispersion of fillers within a polymeric matrix. This investigation considered several methods of dispersing three chosen fillers within an epoxy resin; the same processes were also performed on unfilled materials to investigate any effects they may have on the host material. For this investigation, the epoxy system (EP) was combined with sodium montmorillonite (MMT), micrometric silicon dioxide (SD) or nanometric silicon dioxide (NSD) as fillers. The effect of the different sample preparation routes on breakdown behaviour was then evaluated. While more thorough mixing protocols were found to lead to improved breakdown behaviour in the case of the various filled systems, surprisingly, an entirely equivalent form of behaviour was also seen in the unfilled epoxy. The influence of changes in sample geometry on the breakdown strength was established.

  2. DEGRADATION OF MAGNET EPOXY AT NSLS X-RAY RING.

    Energy Technology Data Exchange (ETDEWEB)

    HU,J.P.; ZHONG,Z.; HAAS,E.; HULBERT,S.; HUBBARD,R.

    2004-05-24

    Epoxy resin degradation was analyzed for NSLS X-ring magnets after two decades of 2.58-2.8 GeV continuous electron-beam operation, based on results obtained from thermoluminescent dosimeters irradiated along the NSLS ring and epoxy samples irradiated at the beamline target location. A Monte Carlo-based particle transport code, MCNP, was utilized to verify the dose from synchrotron radiation distributed along the axial- and transverse-direction in a ring model, which simulates the geometry of a ring quadrupole magnet and its central vacuum chamber downstream of the bending-magnet photon ports. The actual life expectancy of thoroughly vacuum baked-and-cured epoxy resin was estimated from radiation tests on similar polymeric materials using a radiation source developed for electrical insulation and mechanical structure studies.

  3. Physical and chemical durability of cement impregnated epoxy resin

    International Nuclear Information System (INIS)

    Suryantoro

    1997-01-01

    Immobilization of simulation radioactive waste contains Cs and Sr with cement impregnated epoxy resin has been done. Low level liquid waste in 30% weight mixed cement homogeneously and then set in its curing time about 28 days. Waste from was impregnated with epoxy resin (Bisphenol-A-diglycidylether) and use Triethylenteramin as catalyst. the sample of cement impregnated epoxy resin 2.5 cm x 2.5 cm in diameter and length was tested by Paul Weber. The compressive strength was obtained of 4.08 kN.cm - 2. The sochxlet apparatus was run on flow rate of 300 ml/hour at 100 o C and during 24 hours. The leaching rate of Cs was round on 5.5 x 10 - 4 g.cm - 2.d - 1 and Sr was 6.1 x 10 - 4 g.cm - 2.d - 1 (author)

  4. Characterization and analysis of epoxy/clay nanotubes composites

    International Nuclear Information System (INIS)

    Sene, Tarcisio S.; Kock, Thyago; Coelho, Luiz A.F.; Becker, Daniela

    2011-01-01

    An DGEBA epoxy matrix was used aiming to achieve a nanocomposite material, through the dispersion of (CNT) via mechanical stirring followed by sonication. In this work the following characterization were performed: mechanical characterization, differential scanning calorimetry (DSC), wide angle X-ray diffraction (WXRD) and scanning electron microscopy (SEM). The addition of CNT and modified clays promoted the increase of modulus of the epoxy matrix, and a synergistic effect between CNT and both clays could be presumed. SEM images of the fracture surface show the difference between the fracture surface area and the presence of clusters among the samples, allowing a correlation with the modulus of elasticity. X-ray diffractograms from 2Θ = 5 deg showed no peaks for modified clay samples, however it is possible to affirm that modified clay platelets are forming a less organized structure compared to the structure of the clay as natural in epoxy. (author)

  5. Synthesis and characterization of rubbery epoxy/organoclay hectorite nanocomposites

    Directory of Open Access Journals (Sweden)

    2007-12-01

    Full Text Available The present research investigates the morphology, the mechanical, and the viscoelastic properties of rubbery epoxy/clay nanocomposites synthesized by in situ polymerisation of a prepolymer diglycidyl ether of bisphenol-A crosslinked with an aliphatic diamine based on a polyoxypropylene backbone. The inorganic phase was hectorite, exchanged with octadecylammonium ions in order to give organophilic properties to the phyllosilicate. An ultrasonicator was used to disperse the silicate clay layer into epoxy-amine matrix. The morphology of epoxy-hectorite nanocomposites examined by transmission electron microscopy (TEM showed that mixed delamination or intercalation or microdispersion could occur depending on type of organoclay. Moreover, the mechanical and viscoelastic properties were found to be improved with only the treated hectorite.

  6. Health Problems of Epoxy Resins and Amine-curing Agents

    Science.gov (United States)

    Bourne, L. B.; Milner, F. J. M.; Alberman, K. B.

    1959-01-01

    Epoxy resins were first introduced about 10 years ago. Toxic effects, particularly dermatitis, have been frequently described. An investigation into the possible causes of pathological sequelae following the use of epoxy resin/amine mixtures has been undertaken. The cause of most cases of dermatitis and sensitization appears to be uncombined amine which is present in recent mixtures and persists in hardened resin for long periods. The results of experiments with two of the most commonly used resin/amine mixtures confirm this. Cold-cured resins are more dangerous and remain so even when hardened. A simple theory is suggested for the mechanism of the reaction between epoxy resins, amines, and biological systems. This theory leads logically to the handling precautions outlined. Images PMID:13651551

  7. Epoxy foams using multiple resins and curing agents

    Science.gov (United States)

    Russick, Edward M.; Rand, Peter B.

    2000-01-01

    An epoxy foam comprising a plurality of resins, a plurality of curing agents, at least one blowing agent, at least one surfactant and optionally at least one filler and the process for making. Preferred is an epoxy foam comprising two resins of different reactivities, two curing agents, a blowing agent, a surfactant, and a filler. According to the present invention, an epoxy foam is prepared with tailorable reactivity, exotherm, and pore size by a process of admixing a plurality of resins with a plurality of curing agents, a surfactant and blowing agent, whereby a foamable mixture is formed and heating said foamable mixture at a temperature greater than the boiling temperature of the blowing agent whereby said mixture is foamed and cured.

  8. Spatial distribution of volatile compounds in epoxy resins for composites

    International Nuclear Information System (INIS)

    Grayson, M.A.; Wolf, C.J.

    1982-01-01

    Precision abrasion mass spectrometry (PAMS) was used to determine the quantitative distribution profile of water in three epoxy resin systems: tetraglycidyl diaminodiphenyl methane (TGDDM) cured with dicyandiamide (DICY), diglycidyl ether of bisphenol A (DGEBA) cured with DICY, and TGDDM cured with diaminodiphenyl sulfone (DDS). The first two resin systems also contain an epoxy cresol novolac. Specimens of the three resins were exposed to a humid environment for 4 to 2000 hours. The water distribution was determined immediately following environmental exposure. Distribution profiles of oxygen, carbon dioxide, and dichloromethane were also measured in the specimens. A brief description of the PAMS apparatus and a discussion of the distribution profiles of the sorbed gases in the three epoxy resin systems as a function of exposure time are given

  9. Flexural Behavior of Epoxy under Accelerated Hygrothermal Conditions

    Directory of Open Access Journals (Sweden)

    Abulgasem Mohamed Elarbi

    2017-07-01

    Full Text Available Fibers by themselves have a limited use in engineering applications since they cannot transmit loads from one to another; therefore, the matrix material plays an important role in the overall function of the fiber reinforced polymer (FRP composites. This paper intends to study the long term strength of epoxy resins subject to accelerated hygrothermal conditions. Such tests are able to predict the weather durability performance of epoxy materials, which is particularly important for many FRP bonded concrete structures. Several sets of epoxy beam specimens have been constructed and exposed to various hygrothermal environments (25 °C, 100 °C, 180 °C and 0% or 100% relative humidity. Specimens were then evaluated at selected thermal cycles by three-point flexural tests. The flexural strength, mid-span deflection, and stiffness, as well as the mode of failure, have been examined in this study.

  10. Influence of hydroxypropyl cellulose on molecular relaxations of epoxy-amine networks

    Directory of Open Access Journals (Sweden)

    Maria Inez G. Miranda

    2013-01-01

    Full Text Available A dynamic mechanical analysis (DMTA study was conducted on epoxy-amine networks crosslinked in the presence of low contents of hydroxypropyl cellulose (HPC. The epoxy resin chosen was diglycidylether of bisphenol-A (DGEBA and the crosslinker was 4,4'-diaminodiphenylmethane (DDM. In the glassy region, primary (α and secondary (β, γ relaxations originating from the epoxy and HPC components were well detected. Two primary relaxations of neat epoxy and epoxy/HPC systems, referred to as αepoxy and α'epoxy, could be detected, showing a particular glassy behavior for the systems studied in comparison with systems cured in bulk. The main relaxation temperature Tα (at the peak of αepoxy relaxation of the epoxy systems increased slightly with the addition of HPC. The activation energy for this transition (Tα of the epoxy-amine networks was determined both from tan δ and the peak temperatures for the loss modulus measured at various frequencies. The activation energy of the αepoxy relaxation determined from the loss modulus was more reliable than that based on tan δ. The addition of HPC lowered the activation energy of this αepoxy relaxation.

  11. Los cambios de temperatura en los revestimientos epoxi II

    Directory of Open Access Journals (Sweden)

    Fernández Cánovas, M.

    1970-04-01

    Full Text Available This article is the second part of a previous paper published by the author in no. 189 of this magazine. It describes the tests carried out to check the theoretical results published in the earlier article. The tests have consisted in submitting concrete slabs covered with a layer of epoxi mortar to certain thermal conditions, to check the behaviour of the covering in the face of thermal changes. In all the tests, described in detail in the article, the epoxi layer has behaved extremely well, and no bonding failure has been observed, nor failures in the concrete base or in the epoxi layer.Este artículo es la segunda parte de un trabajo publicado por el autor en el número 189 de esta revista, y en él se realiza una descripción de los ensayos prácticos llevados a cabo para complementar el estudio teórico publicado en aquella primera parte. Los ensayos han consistido en someter a placas de hormigón revestidas de una Kipa de mor tero epoxi a determinadas condiciones térmicas, con el fin de poder comprobar el comportamiento del revestimiento frente a los cambios de temperatura. En todos los ensayos realizados y que, con detalle, están descritos en este artículo, el comportamiento de los revestimientos de mortero epoxi ha sido excelente, no habiéndose notado ningún fallo de adherencia, ni roturas en la base de hormigón, ni en la capa de mortero epoxi.

  12. Thermoset Blends of an Epoxy Resin and Polydicyclopentadiene

    Energy Technology Data Exchange (ETDEWEB)

    Rohde, Brian J.; Le, Kim Mai; Krishnamoorti, Ramanan; Robertson, Megan L.

    2016-12-13

    The mechanical properties of two chemically distinct and complementary thermoset polymers were manipulated through development of thermoset blends. The thermoset blend system was composed of an anhydride-cured diglycidyl ether of bisphenol A (DGEBA)-based epoxy resin, contributing high tensile strength and modulus, and polydicyclopentadiene (PDCPD), which has a higher toughness and impact strength as compared to other thermoset polymers. Ultra-small-angle and small-angle X-ray scattering analysis explored the morphology of concurrently cured thermoset blends, revealing a macroscopically phase separated system with a surface fractal structure across blended systems of varying composition. The epoxy resin rich and PDCPD rich phases exhibited distinct glass transitions (Tg’s): the Tg observed at higher temperature was associated with the epoxy resin rich phase and was largely unaffected by the presence of PDCPD, whereas the PDCPD rich phase Tg systematically decreased with increasing epoxy resin content due to inhibition of dicyclopentadiene ring-opening metathesis polymerization. The mechanical properties of these phase-separated blends were in reasonable agreement with predictions by the rule of mixtures for the blend tensile strength, modulus, and fracture toughness. Scanning electron microscopy analysis of the tensile and fracture specimen fracture surfaces showed an increase in energy dissipation mechanisms, such as crazing, shear banding, and surface roughness, as the fraction of the more ductile component, PDPCD, increased. These results present a facile method to tune the mechanical properties of a toughened thermoset network, in which the high modulus and tensile strength of the epoxy resin can be largely retained at high epoxy resin content in the blend, while increasing the fracture toughness.

  13. Toughening mechanism in elastomer-modified epoxy resins, part 2

    Science.gov (United States)

    Yee, A. F.; Pearson, R. A.

    1984-01-01

    The role of matrix ductility on the toughenability and toughening mechanism of elastomer-modified DGEBRA epoxies was investigated. Matrix ductility was varied by using epoxide resins of varying epoxide monomer molecular weights. These epoxide resins were cured using 4,4' diaminodiphenyl sulfone (DDS) and, in some cases, modified with 10% HYCAR(r)CTBN 1300X8. Fracture roughness values for the neat epoxies were found to be almost independent on the monomer molecular weight of the epoxide resin used. However, it was found that the fracture toughness of the elastomer-modified epoxies was very dependent upon the epoxide monomer molecular weight. Tensile dilatometry indicated that the toughening mechanism, when present, is similar to the mechanisms found for the piperidine cured epoxies in Part 1. SEM and OM corroborate this finding. Dynamic mechanical studies were conducted to shed light on the toughenability of the epoxies. The time-dependent small strain behavior of these epoxies were separated into their bulk and shear components. The bulk component is related to brittle fracture, whereas the shear component is related to yielding. It can be shown that the rates of shear and bulk strain energy buildup for a given stress are uniquely determined by the values of Poisson's ratio, nu. It was found that nu increases as the monomer molecular weight of the epoxide resin used increases. This increase in nu can be associated with the low temperature beta relaxation. The effect of increasing cross-link density is to shift the beta relaxation to higher temperatures and to decrease the magnitude of the beta relaxation. Thus, increasing cross-link density decreases nu and increases the tendency towards brittle fracture.

  14. Interlaminar fracture in woven carbon/epoxy laminates

    Directory of Open Access Journals (Sweden)

    Paulo N.B. Reis

    2014-10-01

    Full Text Available This paper describes an experimental study developed to characterize the mode I and mode II fracture toughness of carbon/epoxy woven composites, using DCB and ENF tests, respectively. The laminates were manufactured using an epoxy resin and twelve woven balanced bi-directional layers of carbon fibres, all of them with the same orientation (0/90º. Significant instantaneous delaminations were observed particularly for the DCB specimen, which were responsible for an oscillatory behaviour of GI versus crack length. The maximum values obtained for GIC and GIIC were 281 and 1800 J/m2, respectively.

  15. Radiochemical ageing of epoxy coating for nuclear plants

    International Nuclear Information System (INIS)

    Queiroz, D.P.R.; Fraisse, F.; Fayolle, B.; Kuntz, M.; Verdu, J.

    2010-01-01

    The degradation of an epoxy-amine network exposed to gamma irradiation in oxygen atmosphere has been studied by using a variety of analytical methods, including infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), and sol-gel analysis. Results show that the oxidation of epoxy systems grows with the irradiation dose. Hydroperoxides, which are species resulting from oxidation, were identified and quantified by DSC. As indicated by the sol-gel analysis, the mechanism of degradation of chain scission seems to be predominant over crosslinking. The modifications induced by irradiation reflect in a greater capacity of water absorption.

  16. Effect of pretreatments on electrodeposited epoxy coatings for electronic industries

    Directory of Open Access Journals (Sweden)

    Sironmani Palraj

    2016-02-01

    Full Text Available Waterborne epoxy coatings were prepared on aluminium (Al surfaces by cathodic electro-deposition on the pretreated surface of pickling, phosphating, chromating and anodizing. The electro-deposition experiments were done at two different voltages, 15 V and 25 V at room temperature in 10% epoxy coating formulations. Corrosion and thermal behavior of these coatings were investigated using electrochemical impedance spectroscopy (EIS and thermo gravimetric analysis (TGA. The coating exhibits better corrosion resistance in anodized Al surface than the other. But, TGA studies show that the thermal stability is higher in anodized and chromated Al surfaces. The surface morphology of these coatings were analyzed by SEM and AFM studies.

  17. Effect of MUF/Epoxy Microcapsules on Mechanical Properties and Fractography of Epoxy Materials

    Science.gov (United States)

    Ni, Zhuo; Lin, Yuhao; Du, Xuexiao

    2017-12-01

    Melamine-urea-formaldehyde (MUF) microcapsules were synthesized, morphology, shell thickness, average diameter and interface morphology were studied by scanning electron microscope (SEM). The spherical MUF microcapsules are size normal distribution without adhesion and accumulation, being compact, rough and uneven with a thickness of 3.2μm and a core contents is approximate 70%. A latent imidazoleas the curing agent for a cross-linking chemical reaction for cracking repairing. A good dispersion of MUF microcapsules and a good interfacial bonding are obtained. Effects of MUF microcapsule size and content on bending property and dynamic mechanical propertywere investigated. Both bending strength and storage modulus of the composite are considerably reduced with an increasing addition of the microcapsules whereas the glass transition temperatures are almost not influenced. Significant toughening effects of MUF microcapsules on the epoxy composites are observed at the conditions of different content and size of microcapsule especially at low microcapsule contents and small microcapsule sizes.

  18. Aging results for PRD 49 III/epoxy and Kevlar 49/epoxy composite pressure vessels

    Science.gov (United States)

    Hamstad, M. A.

    1983-01-01

    Kevlar 49/epoxy composite is growing in use as a structural material because of its high strength-to-weight ratio. Currently, it is used for the Trident rocket motor case and for various pressure vessels on the Space Shuttle. In 1979, the initial results for aging of filament-wound cylindrical pressure vessels which were manufactured with preproduction Kevlar 49 (Hamstad, 1979) were published. This preproduction fiber was called PRD 49 III. This report updates the continuing study to 10-year data and also presents 7.5-year data for spherical pressure vessels wound with production Kevlar 49. For completeness, this report will again describe the specimens of the original study with PRD 49 as well as specimens for the new study with Kevlar 49.

  19. Enhanced thermal and mechanical properties of epoxy composites by mixing thermotropic liquid crystalline epoxy grafted graphene oxide

    Directory of Open Access Journals (Sweden)

    B. Qi

    2014-07-01

    Full Text Available Graphene oxide (GO sheets were chemically grafted with thermotropic liquid crystalline epoxy (TLCP. Then we fabricated composites using TLCP-g-GO as reinforcing filler. The mechanical properties and thermal properties of composites were systematically investigated. It is found that the thermal and mechanical properties of the composites are enhanced effectively by the addition of fillers. For instance, the composites containing 1.0 wt% of TLCP-g-GO present impact strength of 51.43 kJ/m2, the tensile strength of composites increase from 55.43 to 80.85 MPa, the flexural modulus of the composites increase by more than 48%. Furthermore, the incorporation of fillers is effective to improve the glass transition temperature and thermal stability of the composites. Therefore, the presence of the TLCP-g-GO in the epoxy matrix could make epoxy not only stronger but also tougher.

  20. Epoxy based oxygen enriched porous carbons for CO2 capture

    Science.gov (United States)

    Tiwari, Deepak; Bhunia, Haripada; Bajpai, Pramod K.

    2017-08-01

    Oxygen enriched carbon adsorbents were successfully synthesized for the first time from template zeolite and epoxy resin as precursor using a nanocasting technique. Carbonization and CO2 activation were performed at various temperatures (500-800 °C) to prepare different carbon structure adsorbents. Several characterization techniques were used to characterize the textural structure, oxygen content and surface functional groups of the adsorbents. The carbon adsorbents show high oxygen content (47.51%), highest surface area (SBET = 686.37 m2 g-1) and pore volume (0.60 cm3 g-1), respectively. The materials were evaluated thermogravimetrically at different adsorption temperatures (30-100 °C) and CO2 concentrations (6-100%). Adsorbent prepared at 700 °C exhibited highest CO2 uptake of 0.91 mmol g-1 due to high surface basicity. Further, regeneration studies of adsorbent exhibited easy regenerability and stability over four multiple adsorptions-desorption cycles. Kinetic models for CO2 adsorption at various CO2 concentrations and temperatures were studied and it was found that the fractional order provided best fitting for the adsorption behavior with an error of less than 3%. The experimental data for CO2 adsorption were analyzed using different isothermal models and found that the Freundlich isothermal model presented perfect fit among all isotherm models depicting heterogeneous adsorbent surface. The isosteric heat of adsorption was estimated to be 11.75 kJ mol-1, indicating physiosorption process. Overall, the above results suggested that the synthesized adsorbent using nanocasting technique provides a feasible way for CO2 capture from point source due to their environmentally benign nature, low cost and stable adsorption capacity.

  1. Research Progress on Microwave Curing of Epoxy Resin and Its Composites

    Directory of Open Access Journals (Sweden)

    XU Xue-hong

    2016-08-01

    Full Text Available Research progress of microwave curing on epoxy resin and its composites was summarized on the basis of introducing the principle of microwave curing technology and its advantages. The paper focused on the effect of microwave curing on the curing rate of epoxy resin and its composites as well as the mechanical and thermal properties of cured products. Two suitable composite systems for wave curing of powder-strengthened epoxy and fiber-strengthened epoxy and a few key technological problems for industrial application are introduced. The application prospect of microwave curing on epoxy resin and its composites was also presented.

  2. Experimental design applied optimization of a state in epoxy clay dispersion

    International Nuclear Information System (INIS)

    Paz, Juliana D'Avila; Bertholdi, Jonas; Folgueras, Marilena Valadares; Pezin, Sergio Henrique; Coelho, Luiz Antonio Ferreira

    2010-01-01

    This paper presents some analysis showed that the exfoliation / intercalation of a montmorillonite clay in epoxy resin such as viscosity, X-ray diffraction (XRD), scanning electron microscopy (SEM) and thermogravimetry (TG). Increasing the viscosity of epoxy resin diglycidyl ether bisphenol A with the addition of clay associated with the sonification system at the time of dispersion is a good indication of exfoliation. The X-ray diffraction already cured composite shows a decrease of crystallinity of clay and EDS microanalysis of SEM, non-uniform dispersion of clay in epoxy resin. Thermal analysis TG composite clay / epoxy shows an increase in thermal stability relative to pure epoxy. (author)

  3. Structural and electrical properties of functionalized multiwalled carbon nanotube/epoxy composite

    International Nuclear Information System (INIS)

    Gantayat, S.; Rout, D.; Swain, S. K.

    2016-01-01

    The effect of the functionalization of multiwalled carbon nanotube on the structure and electrical properties of composites was investigated. Samples based on epoxy resin with different weight percentage of MWCNTs were prepared and characterized. The interaction between MWCNT & epoxy resin was noticed by Fourier transform infrared spectroscopy (FTIR). The structure of functionalized multiwalled carbon nanotube (f-MWCNT) reinforced epoxy composite was studied by field emission scanning electron microscope (FESEM). The dispersion of f-MWCNT in epoxy resin was evidenced by high resolution transmission electron microscope (HRTEM). Electrical properties of epoxy/f-MWCNT nanocomposites were measured & the result indicated that the conductivity increased with increasing concentration of f-MWCNTs.

  4. Two cases of occupational allergic contact dermatitis from a cycloaliphatic epoxy resin in a neat oil: Case Report

    Science.gov (United States)

    Jensen, Charlotte D; Andersen, Klaus E

    2003-01-01

    Background Metal-working fluids contain complex mixtures of chemicals and metal workers constitute a potential risk group for the development of allergic contact dermatitis. Case presentation Two metal workers developed allergic contact dermatitis on the hands and lower arms from exposure to a neat oil used in metal processing. Patch testing revealed that the relevant contact allergen was a cycloaliphatic epoxy resin, 1,2-cyclohexanedicarboxylic acid, bis(oxiranylmethyl) ester, added to the oil as a stabilizer. None of the patients had positive reactions to the bisphenol A-based epoxy resin in the standard series. Conclusions These cases emphasize that well-known contact allergens may show up from unexpected sources of exposure. Further, it can be a long-lasting, laborious process to detect an occupational contact allergen and cooperation from the patient and the manufacturer of the sensitizing product is essential. PMID:12685935

  5. Effect of electron beam irradiation on thermal and mechanical properties of aluminum based epoxy composites

    International Nuclear Information System (INIS)

    Visakh, P.M.; Nazarenko, O.B.; Sarath Chandran, C.; Melnikova, T.V.; Nazarenko, S.Yu.; Kim, J.-C.

    2017-01-01

    The epoxy resins are widely used in nuclear and aerospace industries. The certain properties of epoxy resins as well as the resistance to radiation can be improved by the incorporation of different fillers. This study examines the effect of electron beam irradiation on the thermal and mechanical properties of the epoxy composites filled with aluminum nanoparticles at percentage of 0.35 wt%. The epoxy composites were exposed to the irradiation doses of 30, 100 and 300 kGy using electron beam generated by the linear electron accelerator ELU-4. The effects of the doses on thermal and mechanical properties of the aluminum based epoxy composites were investigated by the methods of thermal gravimetric analysis, tensile test, and dynamic mechanical analysis. The results revealed that the studied epoxy composites showed good radiation resistance. The thermal and mechanical properties of the aluminum based epoxy composites increased with increasing the irradiation dose up to 100 kGy and decreased with further increasing the dose. - Highlights: • The effects of electron beam irradiation on aluminum/epoxy composites were studied. • Changes in thermal and mechanical properties were analyzed. • Irradiation improved the thermal and mechanical properties of aluminum/epoxy composites up to dose of 100 kGy. • The aluminum/epoxy composites appeared more stable to irradiation than the neat epoxy polymer.

  6. Can simultaneous contact allergies to phenyl glycidyl ether and epoxy resins of the bisphenol A/F-types be explained by contamination of the epoxy resins?

    Science.gov (United States)

    Pontén, Ann; Zimerson, Erik; Bruze, Magnus

    2008-11-01

    Simultaneous contact allergies to epoxy resins based on diglycidyl ether of bisphenol A (DGEBA-R) or epoxy resins of the bisphenol F-type and the reactive diluent phenyl glycidyl ether (PGE) have been reported. The reason might be cross-reactivity, exposure to an epoxy resin system with PGE as a component, or contamination by PGE in the epoxy resin. To study contamination by PGE, 20 commercial epoxy resins were analysed for the presence of PGE. To study contact allergy to PGE and its relation to epoxy resins by inserting PGE in the standard series. Among 2227 patients, 7 reacted to PGE. Of 23 (30%) patients, 7 with contact allergy to DGEBA-R and 7/19 (37%) with contact allergy to an epoxy resin of the bisphenol F-type reacted to PGE. All 7 patients with contact allergy to PGE reacted both to the DGEBA-R and to the epoxy resin of the bisphenol F-type. PGE was found in 90% of the investigated resins. The amounts of PGE ranged between 0.004% w/w and 0.18% w/w. Most probably, the presence of PGE as a contaminant in epoxy resins is of minor importance for the sensitization, but possibly the contamination of PGE might elicit contact dermatitis in individuals with a high reactivity to PGE.

  7. Influences of carbon nanofillers on mechanical performance of epoxy resin polymer

    Science.gov (United States)

    Singh, Shraddha; Srivastava, V. K.; Prakash, Rajiv

    2015-03-01

    The influence of multi-walled carbon nanotubes (MWCNTs) and graphene nanoplatelets (GnPs) on epoxy resin was investigated to compare their mechanical properties. MWCNT/epoxy resin and GnP/epoxy resin composites were compared with each other for their tensile strength, compressive strength, Charpy Impact and Izod impact energy with the variation of weight percentage ratio of nanofiller ranging from 0.5, 1.0, 2.0 and 3.0, respectively. The result shows that GnP/epoxy resin composite gave better tensile and compressive strength compared to MWCNT/epoxy resin composite whereas Izod impact energy, Charpy impact energy and dynamic fracture toughness of MWCNT/epoxy resin composite resulted in better impact resistance than the GnP/epoxy resin composite. Thermal stability and microstructural properties of composites were measured using Thermogravimetric analysis (TGA), transmission electron microscope (TEM) and scanning electron microscope (SEM).

  8. Damping properties of epoxy-based composite embedded with sol ...

    Indian Academy of Sciences (India)

    tion energy is changed into electric energy due to the piezo- electric effect ... properties of epoxy-based composites with piezoelectric par- ticles or .... Struct. 7 1. Sun B and Huang D 2001 Compos. Struct. 53 437. Tanimoto T 2007 Compos. Sci. Technol. 67 213. Wang Z, Miao J and Tan C W 2009 Sens. Actuators A149 277.

  9. Degradation Free Vacuum Epoxy Impregnated short REBCO Undulator Magnets

    Science.gov (United States)

    Kesgin, I.; Hasse, Q.; Ivanyushenkov, Y.; Welp, U.

    2017-12-01

    The source of high–brilliance, hard x-ray radiation in light sources and free electron lasers are undulator insertion devices. Recently, REBCO-based superconductors have been demonstrated to be a potential candidate to enhance the performance of the undulator insertion devices. Epoxy impregnation remained as one of the steps which is crucial to fully realize this technology. Epoxy impregnation of magnets is required because it prevents the motion of the wire and provides conduction cooling to the winding layers. Up until now, most of the impregnated REBCO coils/magnets showed some degree of degradation after cold cycles. We developed a vacuum impregnation technique that does not degrade the performance of the short REBCO prototype undulator magnets after cold cycles. The results showed that in order to prevent degradation, a bumper layer between the magnet winding stacks and the epoxy/powder mixture is required. Microstructure images of vacuum impregnated coil packs showed homogenously-spaced REBCO winding layers and very thin epoxy fillings between the layers, which is important for the overall performance of the device.

  10. Piezoelectric and mechanical properties of structured PZT-epoxy composites

    NARCIS (Netherlands)

    James, N.K.; Ende, D.A. van den; Lafont, U.; Zwaag, S. van der; Groen, W.A.

    2013-01-01

    Structured lead zirconium titanate (PZT)-epoxy composites are prepared by dielectrophoresis. The piezoelectric and dielectric properties of the composites as a function of PZT volume fraction are investigated and compared with the corresponding unstructured composites. The effect of poling voltage

  11. Piezoelectric and mechanical properties of structured PZT–epoxy composites

    NARCIS (Netherlands)

    Kunnamkuzhakkal James, N.; Van den Ende, D.; Lafont, U.; Van der Zwaag, S.; Groen, W.A.

    2013-01-01

    Structured lead zirconium titanate (PZT)–epoxy composites are prepared by dielectrophoresis. The piezoelectric and dielectric properties of the composites as a function of PZT volume fraction are investigated and compared with the corresponding unstructured composites. The effect of poling voltage

  12. Crosslinking of epoxy-polysiloxane system by reactive blending

    Czech Academy of Sciences Publication Activity Database

    Gonzales, M.; Kadlec, Petr; Štěpánek, Petr; Strachota, Adam; Matějka, Libor

    2004-01-01

    Roč. 45, č. 16 (2004), s. 5533-5541 ISSN 0032-3861 R&D Projects: GA AV ČR IAA4050008 Keywords : reactive blend ing * siloxane network * epoxy network Subject RIV: CD - Macromolecular Chemistry Impact factor: 2.433, year: 2004

  13. Design and characterization of cellulose nanocrystal-enhanced epoxy hardeners

    Science.gov (United States)

    Shane X. Peng; Robert J. Moon; Jeffrey P. Youngblood

    2014-01-01

    Cellulose nanocrystals (CNCs) are renewable, sustainable, and abundant nanomaterial widely used as reinforcing fillers in the field of polymer nanocomposites. In this study, two-part epoxy systems with CNC-enhanced hardeners were fabricated. Three types of hardeners, Jeffamine D400 (JD400), diethylenetriamine (DETA), and (±)-trans-1,2- diaminocyclohexane (DACH), were...

  14. Study on Concrete Containing Recycled Aggregates Immersed in Epoxy Resin

    Directory of Open Access Journals (Sweden)

    Adnan Suraya Hani

    2017-01-01

    Full Text Available In recent decades, engineers have sought a more sustainable method to dispose of concrete construction and demolition waste. One solution is to crush this waste concrete into a usable gradation for new concrete mixes. This not only reduces the amount of waste entering landfills but also alleviates the burden on existing sources of quality natural concrete aggregates. There are too many kinds of waste but here constructions waste will be the priority target that should be solved. It could be managed by several ways such as recycling and reusing the concrete components, and the best choice of these components is the aggregate, because of the ease process of recycle it. In addition, recycled aggregates and normal aggregates were immersed in epoxy resin and put in concrete mixtures with 0%, 5%, 10% and 20% which affected the concrete mixtures properties. The strength of the concrete for both normal and recycled aggregates has increased after immersed the aggregates in epoxy resin. The percentage of water absorption and the coefficient of water permeability decreased with the increasing of the normal and the recycled aggregates immersed in epoxy resin. Generally the tests which have been conducted to the concrete mixtures have a significant results after using the epoxy resin with both normal and recycled aggregates.

  15. Electrical and thermomechanical properties of epoxy-POSS nanocomposites

    Czech Academy of Sciences Publication Activity Database

    Boček, J.; Matějka, Libor; Mentlík, V.; Trnka, P.; Šlouf, Miroslav

    2011-01-01

    Roč. 47, č. 5 (2011), s. 861-872 ISSN 0014-3057 R&D Projects: GA AV ČR IAA400500701 Institutional research plan: CEZ:AV0Z40500505 Keywords : POSS * epoxy nanocomposite * electrical/dielectrical properties Subject RIV: CD - Macromolecular Chemistry Impact factor: 2.739, year: 2011

  16. The catalystic asymmetric synthesis of optically active epoxy ketones

    NARCIS (Netherlands)

    Marsman, Bertha Gerda

    1981-01-01

    In this thesis the use of catalytic asymmetric synthesis to prepare optically active epoxy ketones is described. This means that the auxiliary chirality, necessary to obtain an optically active product, is added in a catalytic quantity . In principle this is a very efficient way to make opticlly

  17. Impedance characterization of epoxy composite containing conductive hybrid carbon fillers

    Science.gov (United States)

    Othman, Raja Nor; Tawil, Siti Nooraya; Zailan, Suhaila

    2017-08-01

    Epoxy composites containg carbon fillers are prepared in this work with an intention to characterise their electrical properties. The performance of electrical conductivity of epoxy composites is assessed by adding various loadings of conductive carbon fillers into the neat epoxy. First, Carbon Black (CB) was incorporated within epoxy matrix at several loadings. The increase in the specific conductivity of more than five orders of magnitude was observed between 3 wt. % and 4 wt.% CB loading, recorded at 10 kHz frequency. As such, the critical percolation loading, pc was recorded in between 3 wt.% and 4 wt.%. For the samples containing CB at loading 4 wt.% and above, the conductivity remains independent of the frequency, indicating a purely ohmic behaviour. It is also observed that the specific conductivity values can be altered by increasing the hardener stirring time up to 15 minutes, where the pc was successfully lowered down to < 3 wt. % It was further intended to study the hybrid effects by adding CNT to the composites. The conductivity data showed that the composite becomes frequency independent, even at 2 wt. % carbon loading (1 wt. % CB + 1 wt. % CNT), demonstrating the roles contributed by high aspect ratio conductive CNT in enhancing the formation of percolated path at much lower loading.

  18. Photosensitive filler minimizes internal stresses in epoxy resins

    Science.gov (United States)

    Dillon, J. N.

    1967-01-01

    Photosensitive filler is added to curable epoxy resins to minimize stress from internal shrinkage during curing or polymerization. Cinnamic acid resins and cinnamal ketones may be added in the amount of 1 to 3 percent by weight of the resin mixture.

  19. Synthesis of nanosized barium titanate/epoxy resin composites and ...

    Indian Academy of Sciences (India)

    Anechoic chamber; barium titanate; electromagnetic interference and compatibility; epoxy resin composites; microwave absorbers; radio frequency absorbers. ... The reflection loss (RL) and transmission loss (TL) of the composite materials were measured by the reflection/transmission method using a vector network ...

  20. Adhesion of epoxy cataphoretic coatings on Zn alloys

    Directory of Open Access Journals (Sweden)

    JELENA B. BAJAT

    2007-12-01

    Full Text Available One of the most important factors in corrosion prevention by protective coatings is the loss of coating adhesion under environmental influence. In this work, the adhesion of epoxy cataphoretic coatings was examined on steel and steel modified by Zn–Fe and Zn–Co alloys. The dry and wet adhesions of epoxy primers were measured by the direct pull-off standardized procedure, as well as indirectly by the NMP test. The corrosion stability of the coated samples was investigated by electrochemical impedance spectroscopy. It was shown that under dry testing conditions all the samples exhibited very good adhesion. However, different trends of adhesion loss of different protective systems during exposure to a corrosive agent (3 % NaCl solution were observed. The lowest adhesion values were obtained for epoxy coating on the steel substrate. The change in adhesion of the epoxy coating on steel modified by Zn–Co alloy during immersion in 3 % NaCl solution for 24 days was the smallest of all the investigated samples. Electrochemical impedance measurements in 3 % NaCl solution confirmed the good protective properties of this protective system, i.e., greater values of pore resistance were obtained.

  1. Evaluation of epoxy for use on NuSTAR optics

    DEFF Research Database (Denmark)

    An, H.; Christensen, Finn Erland; Doll, M.

    2009-01-01

    The Nuclear Spectroscopic Telescope Array (NuSTAR) is a NASA Small Explorer (SMEX) mission which employs two focusing optics. The optics are composed of stacks of thin mirror shells and spacers. Epoxy is used to bond the mirror shells to the spacers and is a crucial component in determining...

  2. Epoxy-crosslinked sulfonated poly (phenylene) copolymer proton exchange membranes

    Science.gov (United States)

    Hibbs, Michael; Fujimoto, Cy H.; Norman, Kirsten; Hickner, Michael A.

    2010-10-19

    An epoxy-crosslinked sulfonated poly(phenylene) copolymer composition used as proton exchange membranes, methods of making the same, and their use as proton exchange membranes (PEM) in hydrogen fuel cells, direct methanol fuel cell, in electrode casting solutions and electrodes, and in sulfur dioxide electrolyzers. These improved membranes are tougher, have higher temperature capability, and lower SO.sub.2 crossover rates.

  3. Thermal stress failure criteria for a structural epoxy

    Science.gov (United States)

    Côté, Patrice; Desnoyers, Nichola

    2011-09-01

    Representative failure data for structural epoxies can be very difficult to find for the optomechanical engineer. Usually, test data is only available for shear configuration at room temperature and fast pull rate. On the other hand, the slowly induced stress at extreme temperature is for many optical systems the worse-case scenario. Since one of the most referenced epoxy for optical assembly is the 3M™ Scotch-Weld™ Epoxy Adhesive EC-2216 B/A Gray, better understanding its behavior can benefit a broad range of applications. The objective of this paper is two-fold. First, review data for critical parameters such as Young's modulus and coefficient of thermal expansion. Secondly, derive failure criteria from correlation between a thermal stress experiment and a finite element model. Instead of pulling out a standard tensile specimen, it is proposed to test thin bondline geometry to replicate an optical device usage. Four test plates are assembled at the Institut National d'Optique (INO) in Quebec City, Canada with bondlines of 50 μm and 133 μm. To detect the failure of the epoxy, the low level vibration signature of a cantilever Invar plate is monitored as temperature changes. Following the finite element analysis, a failure criterion is found to better match the experimental results than generic lap shear data.

  4. Degradation free epoxy impregnation of REBCO coils and cables

    International Nuclear Information System (INIS)

    Barth, C; Bagrets, N; Weiss, K-P; Bayer, C M; Bast, T

    2013-01-01

    In applications utilizing high-temperature superconductors (HTS) under high mechanical loads as high-field magnets or rotors of generators and motors, the rare-earth–barium–copper-oxide (REBCO) tapes have to be stabilized mechanically. This is achieved using support structures of structural materials and filling the voids in the support through the impregnation of the tapes. The impregnation prevents movement of the tapes and distributes mechanical loads evenly. With high mechanical strengths and low sensitivities to rapid temperature changes, epoxy resins are desired materials for the impregnation of superconductor tapes. However, a strong decrease of the current-carrying capabilities was observed in previous epoxy-impregnated REBCO coils. In this work the thermal expansion mismatches between epoxy resins and REBCO tapes are identified as the cause of these degradations. Fillers are used to reduce the thermal expansions of glues and resins. Mixtures with varying filler contents are analyzed systematically. Their thermal expansions and the corresponding degradations of short REBCO tape samples are measured. A mixture of epoxy resin and filler is found which allows degradation-free impregnation of REBCO tapes. This mixture is validated on a 1.2 m long 15 × 5 Roebel-assembled-coated-conductor (RACC) cable from Industrial Research Limited (IRL). (paper)

  5. Characterization of fracture toughness of epoxy resin after hygrothermal aging

    KAUST Repository

    Quispe, Gustavo Q.

    2013-07-01

    Characterization of fracture toughness of epoxy resin after hygrothermal ageing Gustavo Quino Quispe The aim of this work is to characterize the e ects of hygrothermal aging in the plain strain fracture toughness of the epoxy system composed by cycloaliphatic epoxy resin and diglycidyl ether of bisphenol-A (DGEBA). For this, after having been under hygrothermal aging in a climatic chamber, epoxy samples were studied using ASTM D5045 fracture toughness test, and micrography and roughness measurements of the fracture surface. It is reported a rapid decrease of GIc and KIc during the rst 2 days. Moreover, a numerical model [13] was used to simulate and see with more detail the water absorption in the aged samples. From that, it was observed the heterogeneous distribution of water. Accordingly, it was proposed that the results should be correlated with the water content at the vicinity of the crack tip. Consequently, it was possible to obtain, by quasi-static simulations, the ideal load-displacement curves of crack propagation in the heterogeneous samples. Finally, another contribution of this work is the study of the fracture surface, that gives a clue of the relationship among the fracture energy, the appearance of microcracks in the fracture surface, and the roughness (Ra).

  6. Positron Annihilation in a Rubber Modified Epoxy Resin

    DEFF Research Database (Denmark)

    Mogensen, O. E.; Jacobsen, F. M.; Pethrick, R. A.

    1979-01-01

    Positron annihilation data is reported on a rubber-modified epoxy resin. Studies of the temperature dependence of the o-positronium lifetime indicated the existence of three distinct regions; the associated transition temperatures by comparison with dilatometric data can be ascribed respectively...

  7. Effect of viscoelasticity on adhesion of bioinspired micropatterned epoxy surfaces.

    Science.gov (United States)

    Castellanos, Graciela; Arzt, Eduard; Kamperman, Marleen

    2011-06-21

    The effect of viscoelasticity on adhesion was investigated for micropatterned epoxy surfaces and compared to nonpatterned surfaces. A two-component epoxy system was used to produce epoxy compositions with different viscoelastic properties. Pillar arrays with flat punch tip geometries were fabricated with a two-step soft lithography process. Adhesion properties were measured with a home-built adhesion tester using a spherical sapphire probe as a counter-surface. Compared to flat controls, micropatterned epoxy samples with low viscoelasticity (i.e., low damping factors) showed at least a 20-fold reduction in pull-off force per actual contact area for both low (E' = 2.3 MPa) and high (E' = 2.3 GPa) storage moduli. This antiadhesive behavior may result from poor contact formation and indicates that the adhesion performance of commonly used elastomers for dry adhesives (e.g., polydimethylsiloxane) is governed by the interfacial viscoelasticity. Adhesion significantly increased with increasing viscoelasticity. Micropatterned samples with high viscoelasticity showed a 4-fold reduction in adhesion for aspect ratio (AR) 1.1 patterns but a 2-fold enhancement in adhesion for AR 2.2 patterns. These results indicate that viscoelasticity can enhance the effect of surface patterning on adhesion and should be considered as a significant parameter in the design of artificial patterned adhesives. © 2011 American Chemical Society

  8. The study of epoxy polyamide and polyvinyl resins as corrosion ...

    African Journals Online (AJOL)

    The corrosion resistance of two commonly used protective coatings (epoxy polyamide and polyvinyl resins) in the Niger Delta area of Nigeria has been assessed. The coatings on low carbon steel were subjected to varying conditions of pH, temperature and exposure time and the corrosion rates calculated. At a pH of 2, 3, 4, ...

  9. Mechanisms of Interactions of Energetic Electrons with Epoxy Resins

    Science.gov (United States)

    Gupta, A.; Coulter, D. R.; Tsay, F. D.; Moacanin, J.

    1982-01-01

    The mechanism of deactivation of energy of excitation in a resin system was investigated on optical excitation as well as excitation by high energy electrons. This mechanism involves formation of excited state complexes, known as exciplexes which have a considerable charge transfer character. This mechanism will be used to develop a degradation model for epoxy matrix materials deployed in a space environment.

  10. Epoxy resin monomers with reduced skin sensitizing potency.

    Science.gov (United States)

    O'Boyle, Niamh M; Niklasson, Ida B; Tehrani-Bagha, Ali R; Delaine, Tamara; Holmberg, Krister; Luthman, Kristina; Karlberg, Ann-Therese

    2014-06-16

    Epoxy resin monomers (ERMs), especially diglycidyl ethers of bisphenol A and F (DGEBA and DGEBF), are extensively used as building blocks for thermosetting polymers. However, they are known to commonly cause skin allergy. This research describes a number of alternative ERMs, designed with the aim of reducing the skin sensitizing potency while maintaining the ability to form thermosetting polymers. The compounds were designed, synthesized, and assessed for sensitizing potency using the in vivo murine local lymph node assay (LLNA). All six epoxy resin monomers had decreased sensitizing potencies compared to those of DGEBA and DGEBF. With respect to the LLNA EC3 value, the best of the alternative monomers had a value approximately 2.5 times higher than those of DGEBA and DGEBF. The diepoxides were reacted with triethylenetetramine, and the polymers formed were tested for technical applicability using thermogravimetric analysis and differential scanning calorimetry. Four out of the six alternative ERMs gave polymers with a thermal stability comparable to that obtained with DGEBA and DGEBF. The use of improved epoxy resin monomers with less skin sensitizing effects is a direct way to tackle the problem of contact allergy to epoxy resin systems, particularly in occupational settings, resulting in a reduction in the incidence of allergic contact dermatitis.

  11. Contact allergy to reactive diluents and related aliphatic epoxy resins.

    Science.gov (United States)

    Aalto-Korte, Kristiina; Kuuliala, Outi; Henriks-Eckerman, Maj-Len; Suuronen, Katri

    2015-06-01

    Diglycidyl ether of bisphenol A resin (DGEBA-R) is the most common sensitizer in epoxy systems, but a minority of patients also develop contact allergy to reactive diluents. To analyse the frequency and clinical relevance of allergic reactions to different epoxy reactive diluents and related aliphatic epoxy resins. Test files (January 1991 to June 2014) were screened, and the clinical records of patients with allergic reactions were analysed for occupation, concomitant allergic reactions, and exposure. A total of 67 patients reacted to at least one of the compounds. The largest numbers of allergic reactions were to phenyl glycidyl ether (PGE; n = 41), 1,4-butanediol diglycidyl ether (BDDGE; n = 34), and p-tert-butylphenyl glycidyl ether (PTBPGE; n = 19). Ten of the patients did not have contact allergy to DGEBA-R. The reactions of 5 of these were related to the use of BDDGE-containing products. We found no significant exposure to PGE or PTBPGE in patients sensitized to them, but some of the patients had used cresyl glycidyl ether-containing products. Allergic reactions to reactive diluents and related aliphatic epoxy resins usually occurred together with reactions to DGEBA-R. BDDGE was the clinically most significant compound, and was the sole cause of occupational allergic contact dermatitis in 3 patients. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  12. Nonlinear Inelastic Mechanical Behavior Of Epoxy Resin Polymeric Materials

    Science.gov (United States)

    Yekani Fard, Masoud

    Polymer and polymer matrix composites (PMCs) materials are being used extensively in different civil and mechanical engineering applications. The behavior of the epoxy resin polymers under different types of loading conditions has to be understood before the mechanical behavior of Polymer Matrix Composites (PMCs) can be accurately predicted. In many structural applications, PMC structures are subjected to large flexural loadings, examples include repair of structures against earthquake and engine fan cases. Therefore it is important to characterize and model the flexural mechanical behavior of epoxy resin materials. In this thesis, a comprehensive research effort was undertaken combining experiments and theoretical modeling to investigate the mechanical behavior of epoxy resins subject to different loading conditions. Epoxy resin E 863 was tested at different strain rates. Samples with dog-bone geometry were used in the tension tests. Small sized cubic, prismatic, and cylindrical samples were used in compression tests. Flexural tests were conducted on samples with different sizes and loading conditions. Strains were measured using the digital image correlation (DIC) technique, extensometers, strain gauges, and actuators. Effects of triaxiality state of stress were studied. Cubic, prismatic, and cylindrical compression samples undergo stress drop at yield, but it was found that only cubic samples experience strain hardening before failure. Characteristic points of tensile and compressive stress strain relation and load deflection curve in flexure were measured and their variations with strain rate studied. Two different stress strain models were used to investigate the effect of out-of-plane loading on the uniaxial stress strain response of the epoxy resin material. The first model is a strain softening with plastic flow for tension and compression. The influence of softening localization on material behavior was investigated using the DIC system. It was found that

  13. Improving Fracture Toughness of Epoxy Nanocomposites by Silica Nanoparticles

    Directory of Open Access Journals (Sweden)

    Seyed Reza Akherati Sany

    2017-04-01

    Full Text Available An epoxy resin was modified by silica nanoparticles and cured with an anhydride. The particles with different batches of 12, 20, and 40 nm sizes were each distributed into the epoxy resin ultrasonically. Electron microscopy images showed that the silica particles were well dispersed throughout the resin. Tensile test results showed that Young’s modulus and tensile strength increased with the volume fraction and surface area of the silica particles. The simultaneous use of two average sizes of 20 and 40 nm diameter silica particles still increased these mechanical properties but other combinations of silica particles were unsuccessful. A three-point bending test on each pre-cracked specimen was performed to measure the mode I fracture toughness energy. The fracture energy increased from 283 J/m2 for the unmodified epoxy to about 740 J/m2 for the epoxy with 4.5 wt% of 12 nm diameter silica nanoparticles. The fracture energy of smaller particles was greater because of their higher surface to volume ratio. The fracture energy results showed also that the combined nanoparticles has a synergic effect on the fracture toughness of nanocomposites. Simultaneous use of 10 and 20 nm particles increased the fracture energy to about 770 J/m2. Finally, crack-opening displacement was calculated and found to be in the range of several micrometers which was much larger than the sizes of particles studied. Thus, the toughening mechanisms of crack pinning and crack deflection have a negligible effect on improvement of toughness, nevertheless, the plastic deformation and plastic void growth are dominant mechanisms in epoxy toughening by nanoparticles.

  14. Los cambios de temperatura en los revestimientos epoxi

    Directory of Open Access Journals (Sweden)

    Fernández Cánovas, M.

    1967-04-01

    Full Text Available This theoretical study on the stresses that arise between a layer of epoxi mortar and the concrete base has an essentially practical purpose: to check that there is no failure in the adherence between the epoxi mortars when used as surfacings in general, and especially in pavements of this type. At present, pavements are being prepared for laboratories, workshops, and similar, taking advantage of the excellent properties of these epoxi mortars, but all these uses are being done in an empirical manner, in so far as the probable behaviour of these pavements under the effect of temperature changes is concerned. In this paper an analysis is given of the stresses that result from these temperature changes, and the author reaches significant conclusions.Este estudio teórico sobre las tensiones que se producen entre una capa de mortero epoxi y la base de hormigón tiene un fin eminentemente práctico: comprobar que no se produce desprendimiento en las capas de morteros epoxi en revestimientos en general y, particularmente, en pavimentos de este tipo. Actualmente se están haciendo obras de pavimentación para laboratorios, fábricas, talleres, etc., valiéndose de las inmejorables características resistentes que presentan los indicados morteros, pero todas estas aplicaciones se están realizando de una forma empírica, en lo que se refiere al estudio del comportamiento de estos pavimentos sometidos a cambios de temperatura. En el presente trabajo se hace un análisis de las tensiones que se producen como consecuencia de estos cambios, y en él el autor llega a interesantísimas consecuencias.

  15. Electron beam processed plasticized epoxy coatings for surface protection

    International Nuclear Information System (INIS)

    Ibrahim, Mervat S.; Mohamed, Heba A.; Kandile, Nadia G.; Said, Hossam M.; Mohamed, Issa M.

    2011-01-01

    Highlights: · Coating formulations with EA 70%, HD 20%, and castor oil 10% under 1 Mrad pass -1 irradiation dose showed the best adhesion and passed bending tests. · The prepared EP-SF-An adduct improve anti-corrosion properties of coatings without any significant effect on physical, mechanical and chemical properties of the cured film. The optimum amount of aniline adduct as corrosion inhibitor was found to be 0.4 g for 100 g of coating formulation. · The corrosion inhibition efficiency of the prepared adduct competed the commercial efficiency. - Abstract: Epoxy acrylate oligomer (EA) was plasticized by adding different plasticizers such as epoxidized soybean oil, glycerol and castor oil and cured by electron beam (EB). Different irradiation doses (1, 2.5 and 5 Mrad pass -1 ) were used in the curing process. The effect of both different irradiation doses and plasticizers on the end use performance properties of epoxy acrylate coating namely, pencil hardness, bending test, adhesion test, acid and alkali resistance test were studied. It was observed that incorporation of castor oil in epoxy acrylate diluted by 1,6-hexanediol diacrylate (HD) monomer with a ratio (EA 70%, HD 20%, castor oil 10%) under 1 Mrad pass -1 irradiation dose improved the physical, chemical and mechanical properties of cured films than the other plasticizer. Sunflower free fatty acid was epoxidized in situ under well established conditions. The epoxidized sunflower free fatty acids (ESFA) were subjected to react with aniline in sealed ampoules under inert atmosphere at 140 deg. C. The produced adducts were added at different concentrations to epoxy acrylate coatings under certain EB irradiation dose and then evaluated as corrosion inhibitors for carbon steel surfaces in terms of weight loss measurements and corrosion resistance tests. It was found that, addition of 0.4 g of aniline adduct to 100 g epoxy acrylate formula may give the best corrosion protection for carbon steel and compete the

  16. Analysis of the thermal properties of nanomodified epoxy composite

    Directory of Open Access Journals (Sweden)

    FOMIN Nikolay Egorovich

    2014-02-01

    Full Text Available The paper presents the results of experimental research of epoxy composites modified by nanoparticles. The results were obtained by the method of thermogravimetric analysis. The dependences between the intensity of the processes of thermal degradation in the air and technological factors and content of nanoparticles have been determined. The optimal concentration of 5 types of nanomodifiers besed on carbon nanoclusters adducts, which are functionalized carbon compounds has been revealed. The obvious advantage of these modifiers is their high solubility in polar solvents, that makes the use of these modifiers easier and allows disusing the additional sonication. Investigation of thermooxidation processes of modified epoxy resins was performed in a dynamic mode using TGA/SDTA851e module of STARe System in the temperature range 25÷800⁰C in air atmosphere with simultaneous removal of the gaseous decomposition products. Aluminum oxide (Al₂O₃ was used as the etalon, the temperature speed set was 10 deg./min. It was found out that the process of thermal degradation consists of two stages. The first step is characterized by the main oxidative degradation of polymer and the loss of up to 80% of the original sample weight, the second step is accompanied by the further oxidative decomposition of epoxy composite related to the carbon skeleton destruction. It was proved experimentally that injection of modifiers changes thermal-oxidative decomposition processes and also changes specific energy of epoxy composite according to the type and concentration of nanomodifier. It was shown that the injection of optimal amounts of modifier allows increase of the thermal and energy characteristics, and as a result, the durability of epoxy coatings exposed to aggressive climatic factors.

  17. Synthesis and properties of a bio-based epoxy resin with high epoxy value and low viscosity.

    Science.gov (United States)

    Ma, Songqi; Liu, Xiaoqing; Fan, Libo; Jiang, Yanhua; Cao, Lijun; Tang, Zhaobin; Zhu, Jin

    2014-02-01

    A bio-based epoxy resin (denoted TEIA) with high epoxy value (1.16) and low viscosity (0.92 Pa s, 258C) was synthesized from itaconic acid and its chemical structure was confirmed by 1H NMR and 13C NMR spectroscopy. Its curing reaction with poly(propylene glycol) bis(2-aminopropyl ether) (D230) and methyl hexahydrophthalic anhydride (MHHPA) was investigated. For comparison, the commonly used diglycidyl ether of bisphenol A (DGEBA) was also cured with the same curing agents. The results demonstrated that TEIA showed higher curing reactivity towards D230/MHHPA and lower viscosity compared with DGEBA, resulting in the better processability. Owing to its high epoxy value and unique structure, comparable or better glass transition temperature as well as mechanical properties could be obtained for the TEIA-based network relative to the DGEBA-based network. The results indicated that itaconic acid is a promising renewable feedstock for the synthesis of bio-based epoxy resin with high performance.

  18. Effects of dynamical cure and compatibilization on the morphology and properties of the PP/epoxy blends

    Directory of Open Access Journals (Sweden)

    2007-05-01

    Full Text Available In this paper, effects of dynamical cure and compatibilization on the morphology and properties of the PP/epoxy blends were studied. The addition of maleic anhydride-grafted polypropylene (MAH-g-PP and dynamical cure of epoxy by dicyanamide give rise to decrease the average diameter of epoxy particles in the PP/epoxy blends. The epoxy particles in the PP/epoxy blends can act as effective nucleating agents, accelerating the crystallization of PP component. The dynamical cure and compatibilization increase the kinetic constant K(T of PP crystallization in the PP/epoxy blends. Dynamical cure of the epoxy resin leads to an improvement in the modulus and strength of the PP/epoxy blends, and the addition of MAH-g-PP results in an increase in the impact strength. Dynamic mechanical thermal analysis (DMTA results indicate that the addition of MAH-g-PP improves the compatibility between PP and epoxy resin, and the storage modulus of the PP/epoxy blends increase by dynamical cure. Thermogravimetric analysis (TGA results show dynamical cure of epoxy and addition of MAH-g-PP improved the thermal stability of the PP/epoxy blends. Wide-angle X-ray diffraction (WAXD analysis shows that the PP/epoxy blends have the same crystalline structure as pure PP, indicating dynamical cure and compatibilization do not disturb the crystalline structure of the PP/epoxy blends.

  19. Curing kinetics, mechanism and chemorheological behavior of methanol etherified amino/novolac epoxy systems

    Directory of Open Access Journals (Sweden)

    S. F. Zhao

    2014-02-01

    Full Text Available The curing kinetics and mechanism of epoxy novolac resin (DEN and modified epoxy novolac resin (MDEN with methanol etherified amino resin were studied by means of differential scanning calorimetry (DSC, Fourier transforminfrared (FT-IR spectroscopy and chemorheological analysis. Their kinetics parameters and models of the curing were examined utilizing isoconversional methods, Flynn-Wall-Ozawa and Friedman methods. For the DEN mixture, its average activation energy (Ea was 71.05 kJ/mol and the autocatalytic model was established to describe the curing reaction. The MDEN mixture exhibited three dominant curing processes, termed as reaction 1, reaction 2 and reaction 3; and their Ea were 70.05, 106.55 and 101.91 kJ/mol, respectively. Besides, Ea of reaction 1 was similar to that of DEN mixture, while Ea of reactions 2 and 3 corresponded to that of the etherification reaction between hydroxyl and epoxide group. Moreover, these three dominant reactions were nth order in nature. Furthermore, their curing mechanisms were proposed from the results of DSC and FTIR. The chemorheological behavior was also investigated to obtain better plastics products via optimizing the processing schedules.

  20. Covalent immobilization of molecularly imprinted polymer nanoparticles using an epoxy silane.

    Science.gov (United States)

    Kamra, Tripta; Chaudhary, Shilpi; Xu, Changgang; Johansson, Niclas; Montelius, Lars; Schnadt, Joachim; Ye, Lei

    2015-05-01

    Molecularly imprinted polymers (MIPs) can be used as antibody mimics to develop robust chemical sensors. One challenging problem in using MIPs for sensor development is the lack of reliable conjugation chemistry that allows MIPs to be fixed on transducer surface. In this work, we study the use of epoxy silane to immobilize MIP nanoparticles on model transducer surfaces without impairing the function of the immobilized nanoparticles. The MIP nanoparticles with a core-shell structure have selective molecular binding sites in the core and multiple amino groups in the shell. The model transducer surface is functionalized with a self-assembled monolayer of epoxy silane, which reacts with the core-shell MIP particles to enable straightforward immobilization. The whole process is characterized by studying the treated surfaces after each preparation step using atomic force microscopy, scanning electron microscopy, fluorescence microscopy, contact angle measurements and X-ray photoelectron spectroscopy. The microscopy results show that the MIP particles are immobilized uniformly on surface. The photoelectron spectroscopy results further confirm the action of each functionalization step. The molecular selectivity of the MIP-functionalized surface is verified by radioligand binding analysis. The particle immobilization approach described here has a general applicability for constructing selective chemical sensors in different formats. Copyright © 2015 The Authors. Published by Elsevier Inc. All rights reserved.

  1. Hydrogen bonds, interfacial stiffness moduli, and the interlaminar shear strength of carbon fiber-epoxy matrix composites

    Directory of Open Access Journals (Sweden)

    John H. Cantrell

    2015-03-01

    Full Text Available The chemical treatment of carbon fibers used in carbon fiber-epoxy matrix composites greatly affects the fraction of hydrogen bonds (H-bonds formed at the fiber-matrix interface. The H-bonds are major contributors to the fiber-matrix interfacial shear strength and play a direct role in the interlaminar shear strength (ILSS of the composite. The H-bond contributions τ to the ILSS and magnitudes KN of the fiber-matrix interfacial stiffness moduli of seven carbon fiber-epoxy matrix composites, subjected to different fiber surface treatments, are calculated from the Morse potential for the interactions of hydroxyl and carboxyl acid groups formed on the carbon fiber surfaces with epoxy receptors. The τ calculations range from 7.7 MPa to 18.4 MPa in magnitude, depending on fiber treatment. The KN calculations fall in the range (2.01 – 4.67 ×1017 N m−3. The average ratio KN/|τ| is calculated to be (2.59 ± 0.043 × 1010 m−1 for the seven composites, suggesting a nearly linear connection between ILSS and H-bonding at the fiber-matrix interfaces. The linear connection indicates that τ may be assessable nondestructively from measurements of KN via a technique such as angle beam ultrasonic spectroscopy.

  2. Study of Hyperbranched Poly(ethyleneimine) Polymers of Different Molecular Weight and Their Interaction with Epoxy Resin.

    Science.gov (United States)

    Román, Frida; Colomer, Pere; Calventus, Yolanda; Hutchinson, John M

    2018-03-09

    Two different commercial hyperbranched poly(ethyleneimine)s (HBPEI), with molecular weights (MW) of 800 and 25,000 g/mol, and denoted as PEI800 and PEI25000, respectively, as well as the mixtures with a Diglycidyl Ether of Bisphenol-A (DGEBA) epoxy resin, have been studied using thermal analysis techniques (DSC, TGA), dielectric relaxation spectroscopy (DRS), and dynamic mechanical analysis (DMA). Only a single glass transition is observed in these mixtures by DSC. DRS of the HBPEIs shows three dipolar relaxations: γ, β, and α. The average activation energy for the γ-relaxation is similar for all HBPEIs and is associated with the motion of the terminal groups. The β-relaxation has the same average activation energy for both PEI800 and PEI25000; this relaxation is attributed to the mobility of the branches. The α-relaxation peak for all the HBPEIs is an asymmetric peak with a shoulder on the high temperature side. This shoulder suggests the existence of ionic charge trapped in the PEI. For the mixtures, the γ- and β-relaxations follow the behaviour of the epoxy resin alone, indicating that the epoxy resin dominates the molecular mobility. The α-relaxation by DRS is observed only as a shoulder, as a consequence of an overlap with conductivity effects, whereas by DMA, it is a clear peak.

  3. Study of Hyperbranched Poly(ethyleneimine Polymers of Different Molecular Weight and Their Interaction with Epoxy Resin

    Directory of Open Access Journals (Sweden)

    Frida Román

    2018-03-01

    Full Text Available Two different commercial hyperbranched poly(ethyleneimines (HBPEI, with molecular weights (MW of 800 and 25,000 g/mol, and denoted as PEI800 and PEI25000, respectively, as well as the mixtures with a Diglycidyl Ether of Bisphenol-A (DGEBA epoxy resin, have been studied using thermal analysis techniques (DSC, TGA, dielectric relaxation spectroscopy (DRS, and dynamic mechanical analysis (DMA. Only a single glass transition is observed in these mixtures by DSC. DRS of the HBPEIs shows three dipolar relaxations: γ, β, and α. The average activation energy for the γ-relaxation is similar for all HBPEIs and is associated with the motion of the terminal groups. The β-relaxation has the same average activation energy for both PEI800 and PEI25000; this relaxation is attributed to the mobility of the branches. The α-relaxation peak for all the HBPEIs is an asymmetric peak with a shoulder on the high temperature side. This shoulder suggests the existence of ionic charge trapped in the PEI. For the mixtures, the γ- and β-relaxations follow the behaviour of the epoxy resin alone, indicating that the epoxy resin dominates the molecular mobility. The α-relaxation by DRS is observed only as a shoulder, as a consequence of an overlap with conductivity effects, whereas by DMA, it is a clear peak.

  4. Effect of Glass Reinforced Epoxy (GRE pipe filled with Geopolymer Materials for Piping Application: Compression Properties

    Directory of Open Access Journals (Sweden)

    Abu Hashim Mohammad Firdaus

    2016-01-01

    Full Text Available The aim of this paper is to achieve the highest compressive strength of glass reinforced epoxy pipe with the geopolymer filler content of weight percentage that were used in glass reinforced epoxy pipe. The samples were prepared by using the filament winding method. The effect of weight percentage of geopolymer materials in epoxy hardener was studied under mechanical testing, which is using the compression test. A series of glass reinforced epoxy pipe and glass reinforced epoxy pipe filled with 10 – 40 weight percentage geopolymer filler which is white clay were prepared. The compression strength of the glass reinforced epoxy pipe filled geopolymer materials is determined using Instron Universal Testing under compression mode. It was found that compressive strength for samples with white clay geopolymer filler are much higher compare to glass reinforced epoxy pipe without geopolymer filler. Moreover, the compressive strength of glass reinforced epoxy pipe filled with white clay geopolymer filler was increased from 10 wt% to 30 wt% of geopolymer content. However, the compressive strength of glass reinforced epoxy pipe with white clay geopolymer filler suddenly decreased when added to 40 wt%. The results indicated that the blending of geopolymer materials in epoxy system can be obtained in this study.

  5. Effects of Micro- and Nano-B4C Fillers on Mechanical Properties of Epoxy Composites

    International Nuclear Information System (INIS)

    Jun, Ji Heon; Kim, Jae Woo; Uhm, Young Rang; Rhee, Chang Kyu

    2010-01-01

    Use of nuclear energy always requires safe and efficient transportation and storage of the radioactive wastes. In this regard, development of light and durable materials to shield various radiations is very important. In order to shield neutrons emitted from the spent nuclear fuel, a composite system of epoxy resin and B 4 C filler has been introduced. In this system, high concentration of hydrogen and boron in epoxy matrix can effectively attenuate high-energy neutrons and absorb thermal neutrons, respectively. However, adding fillers into the epoxy matrix has been known to deteriorate the mechanical properties of the epoxy composite because the volume occupied by fillers is equal to the loss volume of matrix resin and adhesion between the particles and the epoxy resin is in general poor. The deterioration of mechanical properties of the boron-epoxy composite makes its application as a neutron shielding material difficult. It should provide a mechanical reliability to endure exterior stresses including sudden deformation, friction and thermal shock, etc. Thus, it is a key issue in producing an epoxy-filler composite to suppress mechanical deterioration while maintaining the shielding capability simultaneously. In this study, micro- and nano-B 4 C particles were dispersed in the three-different epoxy matrix systems. The mechanical properties of the composites were compared with the pure epoxy resin to assess the change of mechanical deterioration. The effect of B 4 C particle size on the mechanical properties of the epoxy composites was also investigated

  6. Comparative Study of Mechanical Properties of MWCNTS/ Epoxy and SWCNTS/ Epoxy Composites

    Directory of Open Access Journals (Sweden)

    Khansaa D. Salman

    2018-03-01

    Full Text Available  The single – walled carbon nanotubes (SWCNTs and multi – walled carbon nanotubes (MWCNTs embedded into resin matrix with different weight concentrations ranging about (0.1, 0.3, 0.5 and 1 wt. %, the nanocomposites are synthesized by casting method. The main applications of this nanocomposites are in the sensors, actuators, radar. Mechanical tests were done for this study such as: tensile test, bending test and hardness test. Also many examinations were utilized to define the microstructure like scanning electron microscopy (SEM, X-ray diffraction and Raman spectroscopy. The results of this work showed that obviously an improvement in mechanical properties of the processed nanocomposites such as young’s modulus, ultimate tensile strength, bending strength and Shore hardness. Also the micrographs of SEM demonstrated that SWCNTs and MWCNTs homogeneously dispersed into epoxy. On the other hand Raman spectra and XRD revealed that same results for SEM. Finally all the results for mechanical properties and microstructure evaluation show that SWCNTs give extremely higher values and properties than MWCNTs.

  7. Evaluation of epoxy resin for cryogenic use by positron annihilation method. Change of characteristics of epoxy resin with plasticizer and positron lifetime

    International Nuclear Information System (INIS)

    Nishijima, Shigehiro; Honda, Yoshihide; Okada, Toichi; Kobayashi, Yoshinori; Namba, Shingo.

    1994-01-01

    The evaluation of unoccupied space in epoxies has been evaluated in terms of positron annihilation method. Based on the evaluated unoccupied space the cohesive condition of the epoxy molecular was modeled. The model suggested that the epoxies were classified into two types that is the epoxy could be explain by the free volume and that by free space. Two former was understood as the epoxy of which molecular network was destroyed by the plasticizer and the latter as that of which molecular weight between crosslinks was changed. In this work the former mechanism was confirmed experimentally. The addition of plasticizer was confirmed not to be effective to improve the cryogenic mechanical properties as expected by the model. (author)

  8. Self-healing epoxy composite with heat-resistant healant.

    Science.gov (United States)

    Yuan, Yan Chao; Ye, Xiao Ji; Rong, Min Zhi; Zhang, Ming Qiu; Yang, Gui Cheng; Zhao, Jian Qing

    2011-11-01

    To provide self-healing epoxy composite with adequate heat resistance for high-performance application, we developed a novel microencapsulated epoxy/mercaptan healing agent. The key measure lies in usage of diglycidyl ether of bisphenol A (EPON 828) as the polymerizable component and 2,4,6-tris(dimethylaminomethyl)phenol (DMP-30) as the catalyst. Because of the higher thermal stability of EPON 828 and lower volatility of DMP-30, the healing agent and the self-healing composite not only survive high-temperature curing and thermal exposure, but also offer satisfactory capability of autonomous properties restoration, as characterized by both fracture mechanics and fatigue tests. Especially when the operation temperature is not higher than 200 °C, the performance of the healing system is nearly independent of thermal history.

  9. Studies on the Microstructure of Epoxy-Cement Composites

    Directory of Open Access Journals (Sweden)

    Łukowski P.

    2016-06-01

    Full Text Available Introduction of polymers into the cement composites improves same of the properties of concretes and mortars. Therefore, the polymer-cement composites are successfully used in construction. The model of microstructure formation in cement composites modified with thermoplastic polymer (pre-mix modifiers has already been developed and successfully implemented. However, the formation of microstructure in the case of epoxy-cement composites ( containing post-mix modifier demonstrates same peculiarities which should be taken into account when modelling the process. The microstructure of epoxy-cement composites and its formation is discussed in the paper. The model is offered, formulated on the basis of the microscopic observations and results of testing.

  10. Structural and functional characterization of barium zirconium titanate / epoxy composites

    Directory of Open Access Journals (Sweden)

    Filiberto González Garcia

    2011-12-01

    Full Text Available The dielectric behavior of composite materials (barium zirconium titanate / epoxy system was analyzed as a function of ceramic concentration. Structure and morphologic behavior of the composites was investigated by X-ray Diffraction (XRD, Fourier transformed infrared spectroscopy (FT-IR, Raman spectroscopy, field emission scanning electron microscopy (FE-SEM and transmission electron microscopy (TEM analyses. Composites were prepared by mixing the components and pouring them into suitable moulds. It was demonstrated that the amount of inorganic phase affects the morphology of the presented composites. XRD revealed the presence of a single phase while Raman scattering confirmed structural transitions as a function of ceramic concentration. Changes in the ceramic concentration affected Raman modes and the distribution of particles along into in epoxy matrix. Dielectric permittivity and dielectric losses were influenced by filler concentration.

  11. Dielectric Behavior of Ceramic (BST/Epoxy Thick Films

    Directory of Open Access Journals (Sweden)

    N. Hadik

    2009-01-01

    Full Text Available Composite materials were made by mixing powders of Ba1−xSrxTiO3 (x=0.2 and 0.4 ceramics and epoxy resin with various volume fractions (vol%. Dielectric measurements of these composites were performed as a function of filler ratio in the range 100–360°K at 10 KHz. The dielectric constant of the composite increased with increasing volume fraction varies slightly with temperature. The 20 vol% of BST(0.4-epoxy composite had the highest dielectric constant of 19.4 and dielectric loss tangent of 0.027. Among the dielectric mixing models presented, the model of Lichtenecker shows the best fit to the experimental data for both composites.

  12. Autonomic Healing of Epoxy Using Micro-Encapsulated Dicyclopentadiene

    Energy Technology Data Exchange (ETDEWEB)

    THOMA, STEVEN G.; GIUNTA, RACHEL K.; STAVIG, MARK E.; EMERSON, JOHN A.; MORALES, ALFREDO M.

    2003-05-01

    The autonomic healing ability of an epoxy adhesive containing micro-encapsulated dicyclopentadiene (DCPD) was evaluated. The epoxy resin used was Epon 828 cured with either Versamid 140 or diethylenetriamine (DETA). Variables included total weight percent of microcapsules (MCs) and catalyst, as well as the catalyst to DCPD ratio. The degree of healing was determined by the fracture toughness before and after ''healing'' using double-cantilever beam analysis. It was found that the degree of self-healing was most directly related to the contact area (i.e. crack width) during healing. Temperature also played a significant role. Observed differences between the results of this study and those in literature are discussed.

  13. Epoxy replication for Wolter x-ray microscope fabrication

    International Nuclear Information System (INIS)

    Priedhorsky, W.

    1981-01-01

    An epoxy replica of a test piece designed to simulate a Wolter x-ray microscope geometry showed no loss of x-ray reflectivity or resolution, compared to the original. The test piece was a diamond-turned cone with 1.5 0 half angle. A flat was fly-cut on one side, then super- and conventionally polished. The replica was separated at the 1.5 0 -draft angle, simulating a shallow angle Wolter microscope geometry. A test with 8.34 A x rays at 0.9 0 grazing angle showed a reflectivity of 67% for the replica flat surface, and 70% for the original. No spread of the reflected beam was observed with a 20-arc second wide test beam. This test verifies the epoxy replication technique for production of Wolter x-ray microscopes

  14. Development of failure criterion for Kevlar-epoxy fabric laminates

    Science.gov (United States)

    Tennyson, R. C.; Elliott, W. G.

    1984-01-01

    The development of the tensor polynomial failure criterion for composite laminate analysis is discussed. In particular, emphasis is given to the fabrication and testing of Kevlar-49 fabric (Style 285)/Narmco 5208 Epoxy. The quadratic-failure criterion with F(12)=0 provides accurate estimates of failure stresses for the Kevlar/Epoxy investigated. The cubic failure criterion was re-cast into an operationally easier form, providing the engineer with design curves that can be applied to laminates fabricated from unidirectional prepregs. In the form presented no interaction strength tests are required, although recourse to the quadratic model and the principal strength parameters is necessary. However, insufficient test data exists at present to generalize this approach for all undirectional prepregs and its use must be restricted to the generic materials investigated to-date.

  15. Epoxy resin casting of trim coils for superconducting cyclotron

    International Nuclear Information System (INIS)

    Hajra, D.P.; Sarkar, S.C.; Saha, Subimal; Chaudhuri, J.; Bhandari, R.K.

    2006-01-01

    The life of any magnet depends on the soundness of the coil insulation, its aging properties and initial and final endurance limitations. The insulation of water-cooled trim coils for superconducting cyclotron is made of glass fibre tape with heat cured unfilled epoxy resin combination. This type of insulation has been selected to achieve excellent stability against thermal and electromagnetic stresses, tight dimensional control, good dielectric strength, non-hygroscopic and considerably low vapour-pressure as it will be inside rough vacuum. The process development and the difficulties encountered for appropriate selection of epoxy resin combination, potting, vacuum process, curing cycle, control of coil dimension to achieve a sound coil absolutely free from cracks, trapped air and voids has been discussed. (author)

  16. Thermal expansion of epoxy-fiberglass composite specimens

    International Nuclear Information System (INIS)

    McElroy, D.L.; Weaver, F.J.; Bridgman, C.

    1986-01-01

    The thermal expansion behavior of three epoxy-fiberglass composite specimens was measured from 20 to 120 0 C (70 to 250 0 F) using a fused quartz push-rod dilatometer. Billets produced by vacuum impregnating layers of two types of fiberglass cloth with an epoxy resin were core-drilled to produce cylindrical specimens. These were used to study expansion perpendicular and parallel to the fiberglass layers. The dilatometer is held at a preselected temperature until steady-state is indicated by stable length and temperature data. Before testing the composite specimens, a reliability check of the dilatometer was performed using a copper secondary standard. This indicated thermal expansion coefficient (α) values within +-2% of expected values from 20 to 200 0 C

  17. Study on voids of epoxy matrix composites sandwich structure parts

    Science.gov (United States)

    He, Simin; Wen, Youyi; Yu, Wenjun; Liu, Hong; Yue, Cheng; Bao, Jing

    2017-03-01

    Void is the most common tiny defect of composite materials. Porosity is closely related to composite structure property. The voids forming behaviour in the composites sandwich structural parts with the carbon fiber reinforced epoxy resin skins was researched by adjusting the manufacturing process parameters. The composites laminate with different porosities were prepared with the different process parameter. The ultrasonic non-destructive measurement method for the porosity was developed and verified through microscopic examination. The analysis results show that compaction pressure during the manufacturing process had influence on the porosity in the laminate area. Increasing the compaction pressure and compaction time will reduce the porosity of the laminates. The bond-line between honeycomb core and carbon fiber reinforced epoxy resin skins were also analyzed through microscopic examination. The mechanical properties of sandwich structure composites were studied. The optimization process parameters and porosity ultrasonic measurement method for composites sandwich structure have been applied to the production of the composite parts.

  18. Shape memory epoxy: a systematic study of their performance

    Science.gov (United States)

    Rousseau, Ingrid A.; Xie, Tao

    2009-03-01

    Seven epoxy-amine polymers showing shape memory (SM) properties were synthesized. Tunable thermal and mechanical properties with glass transition temperatures ranging from 44 to 93 °C were obtained by varying the molecular structures. The epoxy showed excellent SM properties with shape fixity and shape recovery reaching completeness above about 5% strains. The instantaneous SM behavior was found to be independent of materials structure or properties; however, more stringent experimental conditions were found to be detrimental to SM properties for the networks with lower crosslink density and/or higher molecular flexibility/mobility. Indeed, the impact of the shape memory cycling conditions on the SM behavior was investigated. Specifically, the deformation load, the recovery heating rate, the number of SM cycles, and the holding time in the deformed or temporary shape were varied. The mechanical and SM properties of the materials were characterized using dynamic mechanical analysis in tensile mode.

  19. Optimum conditions for radiation curing of polyester/epoxy compositions

    International Nuclear Information System (INIS)

    Brzostowski, A.; Pietrzak, M.

    1982-01-01

    The effects of dose rate of γ 60 Co radiation, heat removal conditions and construction of polyester-epoxy compositions on the curing conditions of the latter were investigated. It was found that the optimum dose rate was within 0.1x10 4 Gy/h and 0.6x10 4 Gy/h for the following composition: 100 parts by weight of polyester resin, 10 to 15 parts by weight of an unsaturated epoxy resin and 100 parts by weight of silicon dioxide. The mixture was well cooled during the curing process. Curing is completed after the absorption of a dose from 0.3x10 4 Gy to 0.45x10 4 Gy. (author)

  20. Preparation and cryogenic properties of radiation stable epoxy composite

    International Nuclear Information System (INIS)

    Wu, Z.X.; Zhang, H.; Yang, H.H.; Chu, X.X.; Li, L.F.; Song, Y.T.; Wu, W.Y.; Liu, H.J.

    2011-01-01

    Impregnating resins in fusion magnet technology are required to be radiation stable, low viscosity, long usable life and high toughness. To meet these objectives, we developed a new epoxy based composite which consists of triglycidyl-p-aminophenol (TGPAP) epoxy resin and isopropylidenebisphenol bis[(2-glycidyloxy-3-n-butoxy)-1-propylether] (IPBE). The ratio of TGPAP to IPBE can be varied to achieve desired viscosity and working time. The boron free glass fiber reinforced composites were prepared by vacuum pressure impregnation. The radiation resistance was evaluated by 60 Co γ-ray irradiation of 1 MGy at ambient temperature. The mechanical properties of the composites have been measured at room temperature and at 77 K. (author)

  1. Novel methodology to evaluate the effect of residual moisture on epoxy resin sealer/dentine interface: a pilot study.

    Science.gov (United States)

    Gibby, S G; Wong, Y; Kulild, J C; Williams, K B; Yao, X; Walker, M P

    2011-03-01

    To evaluate the sealer/dentine interface associated with an epoxy resin sealer using the combination of Goldner's trichrome stain (GTS) and scanning electron microscopy (SEM) to verify the use of the experimental methodology. Extracted human maxillary incisors (6) were subjected to root canal treatment. Subsequent to pulp removal, canal instrumentation and smear layer removal using EDTA and NaOCl, teeth were randomly and equally assigned to a 'wet' or 'dry' group. The 'dry' group was desiccated (95% ethanol/suction/paper points/air-drying), whilst the 'wet' group was treated with a saline rinse/suction/single paper point. Canals were then filled with an epoxy-based resin sealer and warm vertical gutta-percha compaction. After 7-day storage at 37°C, roots from each group were sectioned into apical, middle and coronal horizontal subsections that were cut and split into paired halves and evaluated with GTS or SEM. With GTS sections, hybrid layer and sealer tubular penetration were measured (n=15 measurements/intracanal location/condition) and evaluated using a two-factor repeated measures analysis of variance. The SEM qualitative analysis of paired sections was included as a complementary confirmation of GTS analyses. In dry and wet groups, there was no conspicuous sealer/dentine interface hybrid layer, irrespective of canal location. However, dry specimens exhibited more uniform sealer distribution with deeper tubular penetration in the coronal and middle third (Presin sealer/dentine interface. The pilot data indicated that thorough drying of the root canal system may result in improved epoxy resin sealer distribution and deeper resin sealer tubular penetration, especially in the coronal and middle thirds of root canals. © 2010 International Endodontic Journal.

  2. Improvement of the piezoelectric properties of glass fiber-reinforced epoxy composites by poling treatment

    International Nuclear Information System (INIS)

    Oh, S M; Hwang, H Y

    2013-01-01

    Recently, a new non-destructive method has been proposed for damage monitoring of glass fiber-reinforced polymer composite materials using the piezoelectric characteristics of a polymeric matrix. Several studies of the piezoelectric properties of unidirectional glass fiber epoxy composites and damage monitoring of double-cantilever beams have supported the claim that the piezoelectric method is feasible and powerful enough to monitor the damage of glass fiber epoxy composites. Generally, conventional piezoelectric materials have higher piezoelectric characteristics through poling treatment. In this work, we investigated the change of the piezoelectric properties of glass fiber-reinforced epoxy composites before and after poling treatment. The piezoelectric constants (d 33 ) of glass fiber-reinforced epoxy composites increased by more than 400%. Also, x-ray diffraction tests revealed that poling treatment changed the degree of crystallinity of the epoxy matrix, and this led to the improvement of the piezoelectric characteristics of glass fiber-reinforced epoxy composites. (paper)

  3. Durable superamphiphobic nano-silica/epoxy composite coating via coaxial electrospraying method

    Science.gov (United States)

    Li, Xiaoyan; Li, Hui; Huang, Kai; Zou, Hua; Dengguang, Yu; Li, Ying; Qiu, Biwei; Wang, Xia

    2018-04-01

    In this study, a durable superamphiphobic nano-silica and epoxy composite coating with good environment resistant was successfully fabricated. Fluorinated nano-silica with low surface energy was prepared by in situ sol-gel method, which can be stably dispersed in the solution. Applying fluorinated nano-silica dispersion as sheath and epoxy solution as core, fluorinated nano-silica/epoxy superamphiphobic composite coating was prepared by a coaxial electrospraying method. Fluorinated nano-silica with uniform nano-size was distributed evenly on the micro epoxy particles, showing a special micro-nano hierarchical structure. Nano-indentation shows evident improvement in modulus and hardness of fluorinated nano-silica/epoxy composite coating than that of raw epoxy. In addition, durability of the superamphiphobic coating was assessed by performing harsh chemical environments immersion and scotch tape test.

  4. Development of AlN/Epoxy Composites with Enhanced Thermal Conductivity.

    Science.gov (United States)

    Xu, Yonggang; Yang, Chi; Li, Jun; Mao, Xiaojian; Zhang, Hailong; Hu, Song; Wang, Shiwei

    2017-12-18

    AlN/epoxy composites with high thermal conductivity were successfully prepared by infiltrating epoxy into AlN porous ceramics which were fabricated by gelcasting of foaming method. The microstructure, mechanical, and thermal properties of the resulting composites were investigated. The compressive strengths of the AlN/epoxy composites were enhanced compared with the pure epoxy. The AlN/epoxy composites demonstrate much higher thermal conductivity, up to 19.0 W/(m·K), compared with those by the traditional particles filling method, because of continuous thermal channels formed by the walls and struts of AlN porous ceramics. This study demonstrates a potential route to manufacture epoxy-based composites with extremely high thermal conductivity.

  5. Characterization of epoxy resin containing nano clay prepared by electron beam

    International Nuclear Information System (INIS)

    Park, Jong Seok; Lee, Seung Jun; Lim, Youn Mook; Jeong, Sung In; Gwon, Hui Jeong; Shin, Young Min; Kang, Phil Hyun; Nho, Young Chan

    2015-01-01

    Epoxy resin is widely used as aerospace, automobile, construction and electronics due to their good mechanical and electrical properties and environmental advantages. However, the inherent flammability of epoxy resin has limited its application in some field where good flame retardancy is required. Nano clay can enhance the properties of polymers such as flames retardancy and thermal stability. In this study, we have investigated the nanoclay filled epoxy composite, which has good flame retardancy while maintaining high mechanical properties. The cured epoxy resins were obtained using an electron beam curing process. The nano clays were dispersed in epoxy acrylate solution and mechanically stirred. The prepared mixtures were irradiated using an electron beam accelerator. The composites were characterized by gel content and thermal/ mechanical properties. Moreover, the flammability of the composite was evaluated by limited oxygen index (LOI). The flame retardancy of nano clay filled epoxy composite was evidently improved

  6. The effect of gamma irradiation on the electrical properties of the epoxy resins

    International Nuclear Information System (INIS)

    Gedeon, S.S.

    1986-04-01

    This thesis is concerned primarily with the curing of epoxy resin and the effect of gamma-irradiation on the electrical properties of epoxy resin systems. The particular systems examined were a diglycidyl ether of bisphenol A epoxy resin cured using one of two hardeners. Different methods of examining the curing have been carried out including differential scanning calorimetry (DSC), infrared spectroscopy (I.R.), dielectric measurements, volume resistivity measurements and thermally stimulated discharge current. The results of dielectric relaxation measurements obtained during the curing of the epoxy resin system were interpreted on the basis of a model considering the growing polymer molecules to be in solution, the solvent being the unreacted monomer and hardener. The investigation of the effect of gamma-irradiation on the electrical properties (conduction mechanism and dielectric behaviour) of the epoxy resin system was achieved by examining the electrical properties of the fully cured epoxy resin system before and after irradiation and the results compared. (author)

  7. Bonding and impedance matching of acoustic transducers using silver epoxy.

    Science.gov (United States)

    Son, Kyu Tak; Lee, Chin C

    2012-04-01

    Silver epoxy was selected to bond transducer plates on glass substrates. The properties and thickness of the bonding medium affect the electrical input impedance of the transducer. Thus, the thickness of the silver epoxy bonding layer was used as a design parameter to optimize the structure for the transducer input impedance to match the 50 Ω output impedance of most radio frequency (RF) generators. Simulation and experimental results show that nearly perfect matching is achieved without using any matching circuit. At the matching condition, the transducer operates at a frequency band a little bit below the half-wavelength resonant frequency of the piezoelectric plate. In experiments, lead titanate (PT) piezoelectric plates were employed. Both full-size, 11.5 mm × 2 mm × 0.4 mm, and half-size, 5.75 mm × 2 mm × 0.4 mm, can be well matched using optimal silver epoxy thickness. The transducer assemblies demonstrate high efficiency. The conversion loss from electrical power to acoustic power in soda-lime glass is 4.3 dB. This loss is low considering the fact that the transducers operate at off-resonance by 12%. With proper choice of silver epoxy thickness, the transducer can be matched at the fundamental, the 3rd and 5th harmonic frequencies. This leads to the possible realization of triple-band transducers. Reliability was assessed with thermal cycling test according to Telcordia GR-468-Core recommendation. Of the 30 transducer assemblies tested, none broke until 2900 cycles and 27 have sustained beyond 4050 cycles. Copyright © 2011 Elsevier B.V. All rights reserved.

  8. Liquid crystalline epoxy nanocomposite material for dental application

    Directory of Open Access Journals (Sweden)

    Yun-Yuan Tai

    2015-01-01

    Conclusion: The microhardness of the bracket-like blocks made by our new material is superior to the commercially available brackets, even after thermocycling. Our results indicate that the evaluated liquid crystalline epoxy nanocomposite materials are of an appropriate quality for application in dental core and post systems and in various restorations. By applying technology to refine manufacturing processes, these new materials could also be used to fabricate esthetic brackets for orthodontic treatment.

  9. RADIATION EFFECTS ON EPOXY/CARBON FIBER COMPOSITE

    Energy Technology Data Exchange (ETDEWEB)

    Hoffman, E; Eric Skidmore, E

    2008-12-12

    The Department of Energy Savannah River Site vitrifies nuclear waste incident to defense programs through its Defense Waste Processing Facility (DWPF). The piping in the DWPF seal pot jumper configuration must withstand the stresses during an unlikely but potential deflagration event, and maintain its safety function for a 20-year service life. Carbon fiber-reinforced epoxy composites (CFR) were proposed for protection and reinforcement of piping during such an event. The proposed CFR materials have been ASME-approved (Section XI, Code Case N-589-1) for post-construction maintenance and is DOT-compliant per 49CFR 192 and 195. The proposed carbon fiber/epoxy composite reinforcement system was originally developed for pipeline rehabilitation and post-construction maintenance in petrochemical, refineries, DOT applications and other industries. The effects of ionizing radiation on polymers and organic materials have been studied for many years. The majority of available data are based on traditional exposures to gamma irradiation at high dose rates ({approx}10,000 Gy/hr) allowing high total dose within reasonable test periods and general comparison of different materials exposed at such conditions. However, studies in recent years have shown that degradation of many polymers are sensitive to dose rate, with more severe degradation often observed at similar or even lower total doses when exposed to lower dose rates. This behavior has been primarily attributed to diffusion-limited oxidation which is minimized during very high dose rate exposures. Most test standards for accelerated aging and nuclear qualification of components acknowledge these limitations. The results of testing to determine the radiation resistance and microstructural effects of gamma irradiation exposure on a bisphenol-A based epoxy matrix composite reinforced with carbon fibers are presented. This work provides a foundation for a more extensive evaluation of dose rate effects on advanced epoxy

  10. Effect of carbon nanoparticle addition on epoxy cure

    OpenAIRE

    Dimopoulos, Athanasios

    2007-01-01

    The thesis reports studies of cure kinetics and the glass transition temperature advancements of three commercial epoxy resin systems: MY 750 / HY 5922 (Vantico), MTM 44 -1 (ACG) and 8552 (Hexcel Composites). This investigation was conducted with the utilisation of Differential Scanning Calorimetry (DSC) and Temperature Modulated DSC (TMDSC). Appropriate phenomenological cure kinetics models were built to predict the degree of cure as a function of temperature/time profile. ...

  11. Adhesive Bonding of Aluminium Alloy A5754 by Epoxy Resins

    Directory of Open Access Journals (Sweden)

    Ivan Michalec

    2013-01-01

    Full Text Available Joining thin sheets of aluminium and its alloys is a promising area in the field of joining materials. Nowadays, joining methods that do not melt the material itself are increasingly being utilised. This paper deals with adhesive bonding of aluminium alloy A5754 by two-component epoxy resins. Theresults show that joints bonded by Hysol 9466 have appropriate mechanical properties, but that joints bonded by Hysol 9492 have better thermal stability.

  12. Synthesis and Characterization of Liquid Crystalline Epoxy Resins

    Science.gov (United States)

    2014-01-01

    using thermogravimetric 28 analyzer ( TGA ) on a model Q50 TGA (TA Instruments, Inc.). About 10 mg of resins was placed in an alumina pan and heated...stability of the LCERs was investigated using a thermogravimetric analyzer ( TGA ) on a model Q50 TGA (TA Instruments, Inc.). About 10 mg of resins ...characterization of liquid crystalline epoxy resins Yuzhan Li Iowa State University Follow this and additional works at: http://lib.dr.iastate.edu/etd Part of the

  13. Polymerization of epoxy resins studied by positron annihilation

    International Nuclear Information System (INIS)

    Suzuki, T.; Hayashi, T.; Ito, Y.

    1999-01-01

    The polymerization process of epoxy resins (bisphenol-A dicyanate) was studied using positron-annihilation spectroscopy. The polymerization from monomer to polymer through a polymerization reaction was followed by positron-annihilation lifetime spectroscopy measurements. Resins kept at curing temperatures (120, 150 and 200 o C) changed form from of powder to a solid through a liquid. The size of the intermolecular spaces of the solid samples increased along with the progress of polymerization. (author)

  14. Epoxy-silica hybrids by nonaqueous sol-gel process

    Czech Academy of Sciences Publication Activity Database

    Ponyrko, Sergii; Kobera, Libor; Brus, Jiří; Matějka, Libor

    2013-01-01

    Roč. 54, č. 23 (2013), s. 6271-6282 ISSN 0032-3861 R&D Projects: GA ČR GAP108/12/1459 Grant - others:AV ČR(CZ) M200500903 Institutional support: RVO:61389013 Keywords : epoxy-silica hybrid * nonaqueous sol-gel process * gelation Subject RIV: CD - Macromolecular Chemistry Impact factor: 3.766, year: 2013

  15. Thermal conductivity of microPCMs-filled epoxy matrix composites

    OpenAIRE

    Su, J.F.; Wang, X.Y; Huang, Z.; Zhao, Y.H.; Yuan, X.Y.

    2011-01-01

    Microencapsulated phase change materials (microPCMs) have been widely applied in solid matrix as thermal-storage or temperature-controlling functional composites. The thermal conductivity of these microPCMs/matrix composites is an important property need to be considered. In this study, a series of microPCMs have been fabricated using the in situ polymerization with various core/shell ratio and average diameter; the thermal conductivity of microPCMs/epoxy composites were investigated in detai...

  16. Synthesis and characterization of kraft lignin-based epoxy resins

    OpenAIRE

    El Mansouri, Nour-Eddine; Yuan, Qiaolong; Huang, Farong

    2011-01-01

    Epoxidization is an interesting way to develop a new application of lignin and therefore to improve its application potential. In this work, kraft lignin-based epoxy resins were obtained by the epoxidization reaction, using the kraft lignin recovered directly from pulping liquor and modified by a methylolation reaction. The methylolated lignins were obtained by the reaction of original kraft lignin with formaldehyde and glyoxal, which is a less volatile and less toxic aldehyde. 1H-NMR spectro...

  17. Buckling Analysis of Woven Glass Epoxy Laminated Composite Plate

    OpenAIRE

    M Mohan Kumar

    2013-01-01

    Buckling behavior of laminated composite plates subjected to in-plane loads is an important consideration in the preliminary design of aircraft components. The sizing of many structural subcomponents of the aircraft structures is often determined by stability constraints. The objective of the current study is to understand the influence of the length-to-thickness ratio, the aspect ratio, the fiber orientation and the cut-out shapes on the buckling load for the glass epoxy laminated composit...

  18. Corrosion Protection Properties of Nano NH₂-Reduced Graphene Oxide/Epoxy Composite Coatings Formed by Self-Curing on Magnesium Alloy.

    Science.gov (United States)

    Jin, Tao; Han, Yongqin; Bai, Ruiqin; Liu, Xin

    2018-07-01

    Nano NH2-reduced graphene oxide (NGO) and NGO/epoxy resin coatings were prepared, respectively. NGO/epoxy coating was successfully coated on magnesium alloy substrates. X-ray diffraction patterns, Fourier transform infrared spectroscopy, Scanning electron microscopy techniques were used to characterize the composition and morphology of NGO and composite coatings. The effect of the content of NGO on the corrosion protection performance of coatings was evaluated with electrochemical measurements in 3.5 wt.% NaCl solutions. Tafel and electrochemical impedance spectroscopy analysis revealed that an optimal addition amount of 0.3 wt.% NGO provided the superior corrosion protection properties. The composite coatings exhibited outstanding barrier properties against aggressive species compared to pure epoxy coating. The self-curing reaction of amine and epoxy radicals could produce the compact cross-linking reticular structure. This self-curing reaction was a nucleophilic addition, and amine radical preferred to bond the (b) site of graphene sheets due to the lowest Gibbs free energy. The cross-linking structure and some polar groups could act as a good reservoir for corrosive medium via absorption and fixation.

  19. Preparation and damping properties of fly ash filled epoxy composites

    International Nuclear Information System (INIS)

    Gu Jian; Wu Gaohui; Zhang Qiang

    2007-01-01

    With the purpose of characterizing the high damping properties of the promising low density epoxy/fly ash composites, a series of epoxy composites filled with fly ash of different volume fraction are prepared in this work. Damping tests of cured epoxy composites are performed in the temperature range from -40 to 150 deg. C and in the frequency range from 10 to 800 Hz by using a tension-compression mode. The results show that the values of tangent delta (tan δ) reach their peak values at the glass transition temperatures for the composites with 30-50 vol.% fly ash, and the tan δ values attenuate slowly with the increase of frequency, which indicates that the damping properties of such composites are better than those of other composites. Scanning electron microscopy is used to observe the fractured surfaces of the composites and clarify the dispersion and distribution of fly ash particulates in the matrix. In addition, the thermogravimetric curves are also employed to characterize the heat-resistant performance of the composites

  20. Carbanion as a Superbase for Catalyzing Thiol–Epoxy Photopolymerization

    Directory of Open Access Journals (Sweden)

    Xiaoqing Dong

    2017-08-01

    Full Text Available Photobase generator (PBG-mediated thiol–epoxy photopolymerization has received widedspread attention due to its versatility in various applications. Currently, nearly all reported PBGs release amines as active species. The formed amines induce odor, yellowing, and potential toxicity. In this study, a series of novel thioxanthone-based PBGs, which were able to generate carbanion via decarboxylation under LED light irradiation, were designed and straightforwardly prepared. The formed carbanion can be used as a superbase to catalyze thiol–epoxy polymerization efficiently. Investigation on 1H NMR and FT-IR confirmed the generation of carbanion intermediates. The counteranion significantly affected the photodecarboxylation efficiency. The study of photopolymerization tests, based on real-time FT-IR and dielectric analysis measurements, indicated that the generated carbanion exhibited faster polymerization rate and higher epoxy conversion than traditional superbase 1,8-diazabicyclo[5.4.0]undec-7-ene (DBU. In differential scanning calorimeter, thermogravimetric, and nanoindentation tests, comparable thermal and mechanical properties of the photocured films catalyzed by novel PBGs were obtained. The high initiation ability combined with straightforward synthesis makes these PBGs promising candidates for commercialization.

  1. Structural properties of laminated Douglas fir/epoxy composite material

    Energy Technology Data Exchange (ETDEWEB)

    Spera, D.A. (National Aeronautics and Space Administration, Cleveland, OH (USA). Lewis Research Center); Esgar, J.B. (Sverdrup Technology, Inc., Cleveland, OH (USA)); Gougeon, M.; Zuteck, M.D. (Gougeon Bros., Bay City, MI (USA))

    1990-05-01

    This publication contains a compilation of static and fatigue and strength data for laminated-wood material made from Douglas fir and epoxy. Results of tests conducted by several organizations are correlated to provide insight into the effects of variables such as moisture, size, lamina-to-lamina joint design, wood veneer grade, and the ratio of cyclic stress to steady stress during fatigue testing. These test data were originally obtained during development of wood rotor blades for large-scale wind turbines of the horizontal-axis (propeller) configuration. Most of the strength property data in this compilation are not found in the published literature. Test sections ranged from round cylinders 2.25 in. in diameter to rectangular slabs 6 in. by 24 in. in cross section and approximately 30 ft long. All specimens were made from Douglas fir veneers 0.10 in. thick, bonded together with the WEST epoxy system developed for fabrication and repair of wood boats. Loading was usually parallel to the grain. Size effects (reduction in strength with increase in test volume) are observed in some of the test data, and a simple mathematical model is presented that includes the probability of failure. General characteristics of the wood/epoxy laminate are discussed, including features that make it useful for a wide variety of applications. 9 refs.

  2. High performance wood composites based on benzoxazine-epoxy alloys.

    Science.gov (United States)

    Jubsilp, Chanchira; Takeichi, Tsutomu; Hiziroglu, Salim; Rimdusit, Sarawut

    2008-12-01

    Wood-substituted composites from matrices based on ternary mixtures of benzoxazine, epoxy, and phenolic novolac resins (BEP resins) using woodflour (Hevea brasiliensis) as filler are developed. The results reveal that the addition of epoxy resin into benzoxazine resin can lower the liquefying temperature of the ternary systems whereas rheological characterization of the gel points indicates an evident delay of the vitrification time as epoxy content increased. The gelation of the ternary mixtures shows an Arrhenius-typed behavior and the gel time can be well predicted by an Arrhenius equation with activation energy of 35-40kJ/mol. For wood-substituted composites from highly filled BEP alloys i.e. at 70% by weight of woodflour, the reinforcing effect of the woodflour shows a substantial enhancement in the composite stiffness i.e. 8.3GPa of the filled BEP811 vs 5.9GPa of the unfilled BEP811. The relatively high flexural strength of the BEP wood composites up to 70MPa can also be obtained. The outstanding compatibility between the woodflour and the ternary matrices attributed to the modulus and thermal stability enhancement of the wood composites particularly with an increase of the polybenzoxazine fraction in the BEP alloys.

  3. Study of electron beam curing process using epoxy resin system

    Science.gov (United States)

    Nishitsuji, Delmo A.; Marinucci, Gerson; Evora, Maria C.; de Andrade e Silva, Leonardo G.

    2007-12-01

    Polymeric matrix composite (PMC) has been used in engineering applications instead of metal in the last few years, due to its corrosion resistance and excellent relation between tensile strength/density and elastic modulus/density. However, PMC materials cured by thermal process require high temperature and are time-consuming. The electron beam (EB) curing technology allows its use at room temperature and reduced curing times, and this is one of the main advantages over thermal technology. The aim of this work is to investigate electron beam curable epoxy formulations to use in filament winding processes to produce composite material with similar or better properties than thermal curable composites. The study has been made with commercial epoxy resins and cationic initiators. The epoxy resin samples were irradiated for few minutes with total dose of 150 kGy. The glass transition temperatures ( Tg) were determined by dynamic mechanical analyzer (DMA) and the result was 137 °C. The thermal process was carried out in a furnace following three steps: 4 h at 90 °C, increasing temperature from 90 °C to 130 °C during 4 h and 12 h at 130 °C. The total process time was 20 h. The Tg of this sample was 102 °C.

  4. Study of electron beam curing process using epoxy resin system

    Energy Technology Data Exchange (ETDEWEB)

    Nishitsuji, Delmo A. [Centro Tecnologico da Marinha - CTMSP, Sao Paulo/SP (Brazil); Marinucci, Gerson [Instituto de Pesquisas Energeticas e Nucleares, Av. Prof. Lineu Prestes, 2242 Cidade Universitaria, 05508-000 Sao Paulo/SP (Brazil); Evora, Maria C. [Instituto de Estudos Avancados - IEAv/CTA, Sao Jose dos Campos/SP (Brazil); Andrade Silva, Leonardo G de e [Instituto de Pesquisas Energeticas e Nucleares, Av. Prof. Lineu Prestes, 2242 Cidade Universitaria, 05508-000 Sao Paulo/SP (Brazil)], E-mail: lgasilva@ipen.br

    2007-12-15

    Polymeric matrix composite (PMC) has been used in engineering applications instead of metal in the last few years, due to its corrosion resistance and excellent relation between tensile strength/density and elastic modulus/density. However, PMC materials cured by thermal process require high temperature and are time-consuming. The electron beam (EB) curing technology allows its use at room temperature and reduced curing times, and this is one of the main advantages over thermal technology. The aim of this work is to investigate electron beam curable epoxy formulations to use in filament winding processes to produce composite material with similar or better properties than thermal curable composites. The study has been made with commercial epoxy resins and cationic initiators. The epoxy resin samples were irradiated for few minutes with total dose of 150 kGy. The glass transition temperatures (T{sub g}) were determined by dynamic mechanical analyzer (DMA) and the result was 137 deg. C. The thermal process was carried out in a furnace following three steps: 4 h at 90 deg. C, increasing temperature from 90 deg. C to 130 deg. C during 4 h and 12 h at 130 deg. C. The total process time was 20 h. The T{sub g} of this sample was 102 deg. C.

  5. High Temperature Epoxy Foam: Optimization of Process Parameters

    Directory of Open Access Journals (Sweden)

    Samira El Gazzani

    2016-06-01

    Full Text Available For many years, reduction of fuel consumption has been a major aim in terms of both costs and environmental concerns. One option is to reduce the weight of fuel consumers. For this purpose, the use of a lightweight material based on rigid foams is a relevant choice. This paper deals with a new high temperature epoxy expanded material as substitution of phenolic resin, classified as potentially mutagenic by European directive Reach. The optimization of thermoset foam depends on two major parameters, the reticulation process and the expansion of the foaming agent. Controlling these two phenomena can lead to a fully expanded and cured material. The rheological behavior of epoxy resin is studied and gel time is determined at various temperatures. The expansion of foaming agent is investigated by thermomechanical analysis. Results are correlated and compared with samples foamed in the same temperature conditions. The ideal foaming/gelation temperature is then determined. The second part of this research concerns the optimization of curing cycle of a high temperature trifunctional epoxy resin. A two-step curing cycle was defined by considering the influence of different curing schedules on the glass transition temperature of the material. The final foamed material has a glass transition temperature of 270 °C.

  6. The Modification of a Tetrafunctional Epoxy and Its Curing Reaction

    Directory of Open Access Journals (Sweden)

    Mingming Yu

    2015-06-01

    Full Text Available Recent experimental results showed that the Tg of cured resin scarcely decreased and the impact strength of resins increased by over 50% when a tetrafunctional epoxy named N,N,N',N'-tetraglycidyl-4,4'-diaminodiphenyl ether (TGDDE was introduced to an appropriate flexible chain from a dimer fatty acid (DFA. In order to understand the reason for this phenomenon, the modification and the chemical structure of the prepolymer together with the curing reaction and the viscoelasticity of the cured resins were studied in detail in the present work. The results indicated that the modification would help the prepolymer improve its molecular mobility. As a result, the resins could be further cured, resulting in the cross-linking density increasing. This is because the curing efficiency was increased, but the tetrafunctional epoxy was not cured completely due to its large steric hindrance. Moreover, the flexibility of some parts of the networks was improved, which was beneficial for the toughness of the cured resins. Therefore, the toughness of the tetrafunctional resin was improved with little influence on the thermal properties when the epoxies were modified with an appropriate content of DFA.

  7. Thermal Evaluation of Scorched Graphite-Epoxy Panels by Infrared Scanning

    OpenAIRE

    Slifka, A. J.; Hall, T.; Boltz, E. S.

    2003-01-01

    A simple measurement system is described for evaluating damage to graphite-epoxy panels, such as those used in high-performance aircraft. The system uses a heating laser and infrared imaging system to measure thermal performance. Thermal conductivity or diffusivity is a sensitive indicator of damage in materials, allowing this thermal measurement to show various degrees of damage in graphite-epoxy composites. Our measurements track well with heat-flux damage to graphite epoxy panels. This mea...

  8. Moisture effect on interfacial integrity of epoxy-bonded system: a hierarchical approach

    Science.gov (United States)

    Tam, Lik-ho; Lun Chow, Cheuk; Lau, Denvid

    2018-01-01

    The epoxy-bonded system has been widely used in various applications across different scale lengths. Prior investigations have indicated that the moisture-affected interfacial debonding is the major failure mode of such a system, but the fundamental mechanism remains unknown, such as the basis for the invasion of water molecules in the cross-linked epoxy and the epoxy-bonded interface. This prevents us from predicting the long-term performance of the epoxy-related applications under the effect of the moisture. Here, we use full atomistic models to investigate the response of the epoxy-bonded system towards the adhesion test, and provide a detailed analysis of the interfacial integrity under the moisture effect and the associated debonding mechanism. Molecular dynamics simulations show that water molecules affect the hierarchical structure of the epoxy-bonded system at the nanoscale by disrupting the film-substrate interaction and the molecular interaction within the epoxy, which leads to the detachment of the epoxy thin film, and the final interfacial debonding. The simulation results show good agreement with the experimental results of the epoxy-bonded system. Through identifying the relationship between the epoxy structure and the debonding mechanism at multiple scales, it is shown that the hierarchical structure of the epoxy-bonded system is crucial for the interfacial integrity. In particular, the available space of the epoxy-bonded system, which consists of various sizes ranging from the atomistic scale to the macroscale and is close to the interface facilitates the moisture accumulation, leading to a distinct interfacial debonding when compared to the dry scenario.

  9. Functionalization of Graphene Nanoplatelets Using Sugar Azide for Graphene/Epoxy Nanocomposites

    Science.gov (United States)

    2014-06-20

    in thermal stability of Epoxy /GnP nanocomposite was probably due to poor interfacial adhesion between filler and matrix resulting from inhomogeneous...transfer from filler to matrix. The details of thermal stability and Tg’s of neat Epoxy and nanocomposites have been summarized in Table 1. 4.2.3...Azide for Graphene/ Epoxy Nanocomposites Saswata Bose1, Lawrence T. Drzal 1* Dept of Chemical Engineering and Materials Science Composite Materials

  10. Formation Rate-Limited Pharmacokinetics of Biologically Active Epoxy Transformers of Prodrug Treosulfan.

    Science.gov (United States)

    Romański, Michał; Kasprzyk, Anna; Karbownik, Agnieszka; Szałek, Edyta; Główka, Franciszek K

    2016-05-01

    A prodrug treosulfan (TREO) is being evaluated in clinical trials as a myeloablative agent before hematopoietic stem cell transplantation. The active derivatives of TREO, monoepoxide (EBDM), and diepoxide (DEB) are formed in a pH-dependent nonenzymatic reaction. The aim of the study was to investigate pharmacokinetics of the TREO epoxy transformers in a rabbit model and explain the causes of low plasma concentrations of EBDM and DEB observed in patients receiving high-dose TREO before hematopoietic stem cell transplantation. New Zealand white rabbits (n = 5 per cohort) received an intravenous infusion of TREO (group I), injection of DEB (group II), and injection of a solution containing EBDM (group III). When EBDM and DEB were administered to the rabbits, they underwent a very rapid elimination (half-life 0.069 and 0.046 h) associated with a high systemic clearance (10.0 and 14.0 L h(-1) kg(-1)). After administration of TREO, the t1/2 of EBDM was statistically equal to the t1/2 of the prodrug (1.6 h). To conclude, after administration of TREO, its epoxy transformers demonstrate a formation-limited elimination. Then EBDM and DEB have the same elimination half-life as TREO, but the levels of EBDM and DEB in the body, including plasma, are much lower than TREO on account of their inherently high clearance. Copyright © 2016 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

  11. HEAT TRANSFER THROUGH CYANATE ESTER EPOXY MIX AND EPOXY GPAP–DETDA ELECTRICAL INSULATIONS AT SUPERFLUID HELIUM TEMPERATURE

    CERN Document Server

    Pietrowicz, S; Canfer, S; Jones, S; Baudouy, B

    2011-01-01

    In the framework of the European project EuCARD (FP7) aiming at constructing a high magnetic field accelerator magnet of 13 T with Nb3Sn superconducting cables, new electrical insulation are thermally tested. This technology will use “conventional” electrical insulation in combination with pressurized superfluid helium (He II) or saturated helium at atmospheric pressure as coolant. Two composite insulation systems composed of cyanate ester epoxy mix or a tri-functional epoxy (TGPAP-DETDA) with fiberglass tape frame, have been chosen as potential candidates. The knowledge of their thermal properties is necessary for the thermal design and therefore samples have been tested in pressurized He II where heat is applied perpendicularly to the fibers between 1.6 K and 2.0 K. Overall thermal resistance is determined as a function of temperature and the results are compared with other electrical insulation systems used for accelerator magnets.

  12. Improvement of fatigue resistance of epoxy composite with microencapsulated epoxy-SbF5 self-healing system

    Directory of Open Access Journals (Sweden)

    X. J. Ye

    2017-11-01

    Full Text Available Rapid retardation and arresting of fatigue crack are successfully realized in the epoxy composite containing microencapsulated epoxy and ethanol solution of antimony pentafluoride-ethanol complex (SbF5·HOC2H5/HOC2H5. The effects of (i microcapsules induced-toughening, (ii hydrodynamic pressure crack tip shielding offered by the released healing agent, and (iii polymeric wedge and adhesive bonding of cured healing agent account for extension of fatigue life of the material. The two components of the healing agent can quickly react with each other soon after rupture of the microcapsules, and reconnect the crack only 20 seconds as of the test. The applied stress intensity range not only affects the healing efficiency, but also can be used to evaluate the healing speed. The present work offers a very fast healing system, and sets up a framework for characterizing speed of self-healing.

  13. Epoxy composites filled with boron nitride and aluminum nitride for improved thermal conductivity

    OpenAIRE

    Hutchinson, John M.; Román Concha, Frida Rosario; Cortés Izquierdo, M. Pilar; Calventus Solé, Yolanda

    2017-01-01

    Epoxy composites containing boron nitride (BN) or aluminum nitride (AlN or Al2N3) particles have been studied with a view to obtaining increased thermal conductivity. The effect of these fillers on the cure reaction has been investigated by differential scanning calorimetry (DSC) for two systems, epoxy-diamine and epoxy-thiol, and for volume fractions up to about 35 % of these filler particles. For the epoxy-diamine system, the glass transition temperature of the fully cured system, the heat ...

  14. Enhanced Flexural Strength of Tellurium Nanowires/epoxy Composites with the Reinforcement Effect of Nanowires

    Science.gov (United States)

    Balguri, Praveen Kumar; Harris Samuel, D. G.; Aditya, D. B.; Vijaya Bhaskar, S.; Thumu, Udayabhaskararao

    2018-02-01

    Investigating the mechanical properties of polymer nanocomposite materials has been greatly increased in the last decade. In particular, flexural strength plays a major role in resisting bending and shear loads of a composite material. Here, one dimensional (1D) tellurium nanowires (TeNWs) reinforced epoxy composites have been prepared and the flexural properties of resulted TeNWs/epoxy nanocomposites are studied. The diameter and length of the TeNWs used to make TeNWs/epoxy nanocomposites are 21±2.5 nm and 697±87 nm, respectively. Plain and TeNWs/epoxy nanocomposites are characterized by X-ray diffraction (XRD), thermogravimetric analysis (TGA), and differential thermal analysis (DTA). Furthermore, significant enhancement in the flexural strength of TeNWs/epoxy nanocomposite is observed in comparison to plain epoxy composite, i.e. flexural strength is increased by 65% with the addition of very little amount of TeNWs content (0.05 wt.%) to epoxy polymer. Structural details of plain and TeNWs/epoxy at micrometer scale were examined by scanning electron microscopy (SEM). We believe that our results provide a new type of semiconductor nanowires based high strength epoxy polymer nanocomposites.

  15. Effect of Montmorillonite Nanogel Composite Fillers on the Protection Performance of Epoxy Coatings on Steel Pipelines.

    Science.gov (United States)

    Atta, Ayman M; El-Saeed, Ashraf M; Al-Lohedan, Hamad A; Wahby, Mohamed

    2017-06-02

    Montmorillonite (MMT) clay mineral is widely used as filler for several organic coatings. Its activity is increased by exfoliation via chemical modification to produce nanomaterials. In the present work, the modification of MMT to form nanogel composites is proposed to increase the dispersion of MMT into epoxy matrices used to fill cracks and holes produced by the curing exotherms of epoxy resins. The dispersion of MMT in epoxy improved both the mechanical and anti-corrosion performance of epoxy coatings in aggressive marine environments. In this respect, the MMT surfaces were chemically modified with different types of 2-acrylamido-2-methyl propane sulfonic acid (AMPS) nanogels using a surfactant-free dispersion polymerization technique. The effect of the chemical structure, nanogel content and the interaction with MMT surfaces on the surface morphology, surface charges and dispersion in the epoxy matrix were investigated for use as nano-filler for epoxy coatings. The modified MMT nanogel epoxy composites showed excellent resistance to mechanical damage and salt spray resistance up to 1000 h. The interaction of MMT nanogel composites with the epoxy matrix and good response of AMPS nanogel to sea water improve their ability to act as self-healing materials for epoxy coatings for steel.

  16. Mechanical, morphological and structural properties of cellulose nanofibers reinforced epoxy composites.

    Science.gov (United States)

    Saba, N; Mohammad, F; Pervaiz, M; Jawaid, M; Alothman, O Y; Sain, M

    2017-04-01

    Present study, deals about isolation and characterization of cellulose nanofibers (CNFs) from the Northern Bleached Softwood Kraft (NBSK) pulp, fabrication by hand lay-up technique and characterization of fabricated epoxy nanocomposites at different filler loadings (0.5%, 0.75%, 1% by wt.). The effect of CNFs loading on mechanical (tensile, impact and flexural), morphological (scanning electron microscope and transmission electron microscope) and structural (XRD and FTIR) properties of epoxy composites were investigated. FTIR analysis confirms the introduction of CNFs into the epoxy matrix while no considerable change in the crystallinity and diffraction peaks of epoxy composites were observed by the XRD patterns. Additions of CNFs considerably enhance the mechanical properties of epoxy composites but a remarkable improvement is observed for 0.75% CNFs as compared to the rest epoxy nanocomposites. In addition, the electron micrographs revealed the perfect distribution and dispersion of CNFs in the epoxy matrix for the 0.75% CNFs/epoxy nanocomposites, while the existence of voids and agglomerations were observed beyond 0.75% CNFs filler loadings. Overall results analysis clearly revealed that the 0.75% CNFs filler loading is best and effective with respect to rest to enhance the mechanical and structural properties of the epoxy composites. Copyright © 2017 Elsevier B.V. All rights reserved.

  17. Effect of Thermally Reduced Graphene Oxide on Mechanical Properties of Woven Carbon Fiber/Epoxy Composite

    Directory of Open Access Journals (Sweden)

    Nitai Chandra Adak

    2018-02-01

    Full Text Available Thermally reduced graphene oxide (TRGO was incorporated as a reinforcing filler in the epoxy resin to investigate the effect on the mechanical properties of carbon fiber (CF/epoxy composites. At first, the epoxy matrix was modified by adding different wt % of TRGO from 0.05 to 0.4 wt % followed by the preparation of TRGO/CF/epoxy composites througha vacuum-assisted resin transfer molding process. The prepared TRGO was characterized by using Fourier transform infrared spectroscopy, Raman Spectroscopy and field emission scanning electron microscopy (FE-SEM techniques. It was observed that the wrinkled structure of synthesized TRGO may be helpful to interlock with the epoxy resin and CF.The inter-laminar shear strength, in-plane fracture toughness and impact strength increased by ~67%, 62% and 93% at 0.2 wt % of TRGO loading in the CF/epoxy composites as compared to the CF reinforced epoxy. The mechanical properties of the hybrid composites decreased beyond the 0.2 wt % of TRGO incorporation in the epoxy resin. The fracture surfaces of the hybrid composites were studied by FE-SEM image analysis to investigate the synergistic effect of TRGO in the CF/epoxy composite. This study suggested that TRGO could be used asgood nanofiller to resist the matrix and fiber fracture.

  18. Mechanical Properties of Epoxy Resin Mortar with Sand Washing Waste as Filler

    OpenAIRE

    Yemam, Dinberu Molla; Kim, Baek-Joong; Moon, Ji-Yeon; Yi, Chongku

    2017-01-01

    The objective of this study was to investigate the potential use of sand washing waste as filler for epoxy resin mortar. The mechanical properties of four series of mortars containing epoxy binder at 10, 15, 20, and 25 wt. % mixed with sand blended with sand washing waste filler in the range of 0–20 wt. % were examined. The compressive and flexural strength increased with the increase in epoxy and filler content; however, above epoxy 20 wt. %, slight change was seen in strength due to increas...

  19. A study on the resistance performance of epoxy nano-composites under the vacuum ultraviolet irradiation

    Science.gov (United States)

    Liu, Yang; Li, Guo-hui; Jiang, Li-xiang

    2008-12-01

    Irradiation damage effects of the epoxy resin 648 and epoxy nano-composites are studied by means of simulating the vacuum ultraviolet (VUV) irradiation whose wavelength ranges from 5 to 200 nm. Experimental results of the mass loss, SEM and XPS show that nano-TiO 2 particles exhibit better resistance performance under VUV. Comparing with epoxy resin, the epoxy nano-composite brings significantly less mass loss, slighter flexural strength variation and decreasing gas extraction with less gas component varieties after irradiation. What is more, no new carbon peak-value has been found and principle components of Ols peak-value remain unchanged on the surface.

  20. Nanosilica Modification of Elastomer-Modified VARTM Epoxy Resins for Improved Resin and Composite Toughness

    National Research Council Canada - National Science Library

    Robinette, Jason; Bujanda, Andres; DeSchepper, Daniel; Dibelka, Jessica; Costanzo, Philip; Jensen, Robert; McKnight, Steven

    2007-01-01

    Recent publications have reported a synergy between rubber and silica in modified epoxy resins that results in significantly improved fracture toughness without reductions in other material properties...

  1. Preparation and Performance of Amphiphilic Random Copolymer Noncovalently Modified MWCNTs/Epoxy Composite

    Directory of Open Access Journals (Sweden)

    MA Qiang

    2016-09-01

    Full Text Available An amphiphilic random copolymer of polyglycidyl methacrylate-co-N-vinyl carbazole P(GMA-co-NVC was synthesized by free radical polymerization and was used to noncovalently modify multi-walled carbon nanotubes (MWCNTs. The obtained P(GMA-co-NVC/MWCNTs was mixed with epoxy resin and used to reinforce epoxy resin. Polymer modified carbon nanotubes/epoxy resin composites were prepared by a casting molding method. Tensile test, electrical resistivity test and differential scanning calorimeter(DSC analysis were used to study the effect of polymer modified carbon nanotubes on the mechanical, electrical, and thermal properties of epoxy resin. The results show that the epoxy composite reinforced with P(GMA-co-NVC/MWCNTs shows a remarkable enhancement in both tensile strength and elongation at break compared to either the pure epoxy or the pristine MWCNTs/epoxy composites. In addition, the electrical conductivity of epoxy is significantly improved and the volume resistivity decreases from 1014Ω·m to 106Ω·m with 0.25% mass fraction loading of P(GMA-co-NVC/MWCNTs. Moreover, glass transition temperature of the epoxy composite also increases from 144℃ to 149℃.

  2. Characterization of epoxy hybrid composites filled with cellulose fibers and nano-SiC

    KAUST Repository

    Alamri, H.

    2012-04-06

    Three different approaches have been applied and investigated to enhance the thermal and mechanical properties of epoxy resin. Epoxy system reinforced with either recycled cellulose fibers (RCF) or nanosilicon carbide (n-SiC) particles as well as with both RCF and n-SiC has been fabricated and investigated. The effect of RCF/n-SiC dispersion on the mechanical and thermal properties of these composites has been characterized. The fracture surface morphology and toughness mechanisms were investigated by scanning electron microscopy. The dispersion of n-SiC particles into epoxy nanocomposites was studied by synchrotron radiation diffraction and transmission electron microscopy. Results indicated that mechanical properties increased as a result of the addition of n-SiC. The presence of RCF layers significantly increased the mechanical properties of RCF/epoxy composites when compared with neat epoxy and its nanocomposites. The influence of the addition of n-SiC to RCF/epoxy composites in mechanical properties was found to be positive in toughness properties. At high temperatures, thermal stability of neat epoxy increased due to the presence of either n-SiC particles or RCF layers. However, the presence of RCF accelerated the thermal degradation of neat epoxy as well as the addition of n-SiC to RCF/epoxy samples increased the rate of the major thermal degradation. © 2012 Wiley Periodicals, Inc.

  3. Synthesis of Polyurethane Modified Epoxy From Acrylic Polyol with Temperature Variation and Polyurethane Composition

    OpenAIRE

    Triwulandari, Evi; Ghozali, Muhammad

    2013-01-01

    Polyurethane-modified epoxy has been synthesized using acrylic polyol and tolonate as polyurethane component. Epoxy modification process was conducted at 50o, 70o and 90 oC; 10 %, 20 %, 30 %, 40 % (%w/w) polyurethane to epoxy; with solvent and without solvent as well. Characterization of polyurethane-modified epoxy has been done by determining rest of isocyanate to calculate isocyanate conversion level, Fourier Transform- Infra Red (FT-IR) analysis and 1H-Nuclear Magnetic Resonance (1H-NMR). ...

  4. Cross-Sectional Study of Respiratory Symptoms, Spirometry, and Immunologic Sensitivity in Epoxy Resin Workers.

    Science.gov (United States)

    Hines, Stella E; Barker, Elizabeth A; Robinson, Maura; Knight, Vijaya; Gaitens, Joanna; Sills, Michael; Duvall, Kirby; Rose, Cecile S

    2015-12-01

    An epoxy resin worker developed hypersensitivity pneumonitis requiring lung transplantation and had an abnormal blood lymphocyte proliferation test (LPT) to an epoxy hardener. We assessed the prevalence of symptoms, abnormal spirometry, and abnormal epoxy resin LPT results in epoxy resin workers compared to unexposed workers. Participants completed questionnaires and underwent spirometry. We collected blood for epoxy resin LPT and calculated stimulation indices for five epoxy resin products. We compared 38 exposed to 32 unexposed workers. Higher exposed workers were more likely to report cough (OR 10.86, [1.23-infinity], p = 0.030) or wheeze (OR 4.44, [1.00-22.25], p = 0.049) than unexposed workers, even controlling for smoking. Higher exposed workers were more likely to have abnormal FEV1 than unexposed workers (OR 10.51, [0.86-589.9], p = 0.071), although not statistically significant when adjusted for smoking. There were no differences in proportion of abnormal epoxy resin system LPTs between exposed and unexposed workers. In summary, workers exposed to epoxy resin system chemicals were more likely to report respiratory symptoms and have abnormal FEV1 than unexposed workers. Use of epoxy resin LPT was not helpful as a biomarker of exposure and sensitization. © 2015 Wiley Periodicals, Inc.

  5. Cross‐Sectional Study of Respiratory Symptoms, Spirometry, and Immunologic Sensitivity in Epoxy Resin Workers

    Science.gov (United States)

    Barker, Elizabeth A.; Robinson, Maura; Knight, Vijaya; Gaitens, Joanna; Sills, Michael; Duvall, Kirby; Rose, Cecile S.

    2015-01-01

    Abstract Objectives An epoxy resin worker developed hypersensitivity pneumonitis requiring lung transplantation and had an abnormal blood lymphocyte proliferation test (LPT) to an epoxy hardener. We assessed the prevalence of symptoms, abnormal spirometry, and abnormal epoxy resin LPT results in epoxy resin workers compared to unexposed workers. Methods Participants completed questionnaires and underwent spirometry. We collected blood for epoxy resin LPT and calculated stimulation indices for five epoxy resin products. Results We compared 38 exposed to 32 unexposed workers. Higher exposed workers were more likely to report cough (OR 10.86, [1.23‐infinity], p = 0.030) or wheeze (OR 4.44, [1.00‐22.25], p = 0.049) than unexposed workers, even controlling for smoking. Higher exposed workers were more likely to have abnormal FEV1 than unexposed workers (OR 10.51, [0.86‐589.9], p = 0.071), although not statistically significant when adjusted for smoking. There were no differences in proportion of abnormal epoxy resin system LPTs between exposed and unexposed workers. Conclusions In summary, workers exposed to epoxy resin system chemicals were more likely to report respiratory symptoms and have abnormal FEV1 than unexposed workers. Use of epoxy resin LPT was not helpful as a biomarker of exposure and sensitization. PMID:26553118

  6. The characteristics of epoxy resin cured by γ-ray and E-beam

    International Nuclear Information System (INIS)

    Nho, Y.C.; Kang, Phil Hyun; Park, Jong Seok

    2004-01-01

    Epoxy resins are widely used as high-performance thermosetting resins for many industrial applications. In this study, the effect of an electron beam (E-beam) and γ-ray irradiation on the curing of epoxy resins was investigated. Diglycidyl ether of bisphenol-A(DGEBA), diglycidyl ether of bisphenol-F(DGEBF) as epoxy resins, triarylsulfonium hexafluoroantimonate(TASHFA), and triarylsulfonium hexafluorophosphate(TASHFP) as initiators were used in this study. The chemical and mechanical characteristics of irradiated epoxy resins were compared after curing of E-beam and γ-ray irradiation up to 50 kGy in N 2 and air atmosphere. We ascertained the effect of oxygen on the radiation curing of epoxy resin. The thermal properties of cured epoxy were investigated using DMA and TGA. Mechanical properties such as flexural strength were measured. The chemical structures of cured epoxy were characterized by FT-NIR. The gel fraction and the stress at yield of epoxy resins irradiated by E-beam and γ-ray in N 2 atmosphere were also compared with those of epoxy resins irradiated by E-beam and γ-ray in air

  7. Thermodynamic study on phase equilibrium of epoxy resin/thermoplastic blends

    International Nuclear Information System (INIS)

    Figueruelo, Juan E.; Gomez, Clara M.; Monzo, Isidro S.; Abad, Concepcion; Campos, Agustin

    2008-01-01

    The experimental phase diagrams (cloud point curves) of three series of epoxy/thermoplastic blends, namely, epoxy/polystyrene (PS), epoxy/poly(ether sulfone) (PES), and epoxy/poly(ether imide) (PEI) as a function of molar mass and composition have been analysed from a thermodynamic point of view. A model based on the Flory-Huggins lattice theory considering the concentration dependence of the interaction parameter as predicted by Koningsveld was employed to determine the equilibrium compositions, and concentration and temperature dependent interaction parameters. Binodal, spinodal, and critical point data have been computed and show good agreement with experimental data

  8. Effects of colloidal nanosilica on the rheological properties of epoxy resins filled with organoclay.

    Science.gov (United States)

    Nguyen, Dinh Huong; Song, Gwang Seok; Lee, Dai Soo

    2011-05-01

    The rheological properties of epoxy resins filled with organoclay and colloidal nanosilica were investigated by employing a parallel plate rheometer in flow mode at 25 degrees C. Shear thickening and shear thinning behaviors were observed in the epoxy resins filled with a mixture of organoclay and colloidal nanosilica. Minima were observed in the relaxation time of the systems consisting of epoxy resins filled with organoclay and colloidal silica as the content of colloidal nanosilica was increased. It seems that the colloidal nanosilica increased the mobility of the filled epoxy resins and reduced the interactions between the silicate layers in the systems.

  9. Effect of epoxy resin and hardener containing microcapsules on healing efficiency of epoxy adhesive based metal joints

    International Nuclear Information System (INIS)

    Khan, Nazrul Islam; Halder, Sudipta; Goyat, M.S.

    2016-01-01

    Dual component microcapsules of epoxy resin and polyamine hardener with polymethyl methacrylate (PMMA) shell were synthesized using a water-oil-water emulsion solvent evaporation method. The high concentration of sodium dodecyl sulfate (SDS) was used to reduce the thickness of shell wall of dual component microcapsules. The dual microcapsules of 1:1 weight ratio were introduced in the epoxy adhesive to study the healing effect. The morphology, chemical structure and thermal characteristics of the microcapsules were characterized by scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA), respectively. The insertion of dual component microcapsules in epoxy matrix reduced the lap shear strength of adhesive joints, which may be attributed to the generation of stress concentration cites because of micron sized capsules. However, the extension and absorbed failure energy of adhesive joints under uniaxial loading increased with the increase of concentration of dual microcapsules. The viscoelastic nature of the dual microcapsules may be responsible for this enhancement. Significant enhancement in the healing efficiency (90.93%) of the joints was achieved for 10 wt% of dual microcapsules. The crack pinning and crack blunting mechanisms at the vicinity of the crack path adjacent to the microcapsules were found responsible for significant enhancement in the healing efficiency of the adhesive joints. - Highlights: • High SDS concentration was used to control the dual component microcapsules shell wall thickness. • Self-healing performance of dual component microcapsules reinforced epoxy adhesive based single lap joints was studied. • 90.93% of the damage healing was achieved for self-healing adhesive based single lap joints. • Increase in concentration of microcapsules reduces the lap shear properties of the self-healing joints.

  10. Effect of epoxy resin and hardener containing microcapsules on healing efficiency of epoxy adhesive based metal joints

    Energy Technology Data Exchange (ETDEWEB)

    Khan, Nazrul Islam [Department of Mechanical Engineering, National Institute of Technology Silchar, Silchar 788010, Assam (India); Halder, Sudipta, E-mail: shalder@nits.ac.in [Department of Mechanical Engineering, National Institute of Technology Silchar, Silchar 788010, Assam (India); Goyat, M.S. [Department of Physics, University of Petroleum & Energy Studies, Dehradun, Uttarakhand 248007 (India)

    2016-03-01

    Dual component microcapsules of epoxy resin and polyamine hardener with polymethyl methacrylate (PMMA) shell were synthesized using a water-oil-water emulsion solvent evaporation method. The high concentration of sodium dodecyl sulfate (SDS) was used to reduce the thickness of shell wall of dual component microcapsules. The dual microcapsules of 1:1 weight ratio were introduced in the epoxy adhesive to study the healing effect. The morphology, chemical structure and thermal characteristics of the microcapsules were characterized by scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA), respectively. The insertion of dual component microcapsules in epoxy matrix reduced the lap shear strength of adhesive joints, which may be attributed to the generation of stress concentration cites because of micron sized capsules. However, the extension and absorbed failure energy of adhesive joints under uniaxial loading increased with the increase of concentration of dual microcapsules. The viscoelastic nature of the dual microcapsules may be responsible for this enhancement. Significant enhancement in the healing efficiency (90.93%) of the joints was achieved for 10 wt% of dual microcapsules. The crack pinning and crack blunting mechanisms at the vicinity of the crack path adjacent to the microcapsules were found responsible for significant enhancement in the healing efficiency of the adhesive joints. - Highlights: • High SDS concentration was used to control the dual component microcapsules shell wall thickness. • Self-healing performance of dual component microcapsules reinforced epoxy adhesive based single lap joints was studied. • 90.93% of the damage healing was achieved for self-healing adhesive based single lap joints. • Increase in concentration of microcapsules reduces the lap shear properties of the self-healing joints.

  11. Corrosion performance of epoxy-coated reinforcement in aggressive environments

    Science.gov (United States)

    Vaca Cortes, Enrique

    The objective of this research was to investigate the integrity and corrosion performance of epoxy-coated reinforcement in aggressive environments. A series of experimental studies were conducted: (a) hot water immersion and knife adhesion testing for assessment of coating adhesion; (b) materials and procedures for repairing coating damage; (c) degree of mechanical damage caused during concrete placement when using metal head and rubber head vibrators; (d) accelerated corrosion of coated bars embedded in macrocell and beam specimens placed in a corrosive environment for more than four years. The effects of coating condition and amount of damage, repaired vs. unrepaired damage, bar fabrication, and concrete cracking were studied. Regardless of coating condition, the performance of epoxy-coated bars was better than that of uncoated bars. Unlike black bars, coated bars did not exhibit deep pitting or substantial loss of cross section at crack locations. Damage to epoxy coating was the most significant factor affecting corrosion performance. Bars with coating in good condition, without any visible damage, performed best. The greater the size and frequency of damage, the more severe and extensive the amount of corrosion. The performance of bars that were fabricated or bent after coating was worse than that of coated straight bars. Mixing coated and uncoated bars in the same concrete member led to undesirable performance. Patching damaged coating reduced but did not prevent corrosion, particularly at bar ends. The most important factor in coating repair was the type and properties of the patching material. Surface preparation prior to coating had little effect. The absence of cracks in the concrete delayed, but did not prevent the onset of corrosion of coated bars. During consolidation of concrete, rubber head vibrators caused less damage to epoxy-coated reinforcement than did comparable metal heads. Hot water and adhesion tests were useful and practical for evaluating

  12. Fabrication and Characterization of Silicon Carbide Epoxy Composites

    Science.gov (United States)

    Townsend, James

    Nanoscale fillers can significantly enhance the performance of composites by increasing the extent of filler-to-matrix interaction. Thus far, the embedding of nanomaterials into composites has been achieved, but the directional arrangement has proved to be a challenging task. Even with advances in in-situ and shear stress induced orientation, these methods are both difficult to control and unreliable. Therefore, the fabrication of nanomaterials with an ability to orient along a magnetic field is a promising pathway to create highly controllable composite systems with precisely designed characteristics. To this end, the goal of this dissertation is to develop magnetically active nanoscale whiskers and study the effect of the whiskers orientation in a polymer matrix on the nanocomposite's behavior. Namely, we report the surface modification of silicon carbide whiskers (SiCWs) with magnetic nanoparticles and fabrication of SiC/epoxy composite materials. The magnetic nanoparticles attachment to the SiCWs was accomplished using polyelectrolyte polymer-to-polymer complexation. The "grafting to" and adsorption techniques were used to attach the polyelectrolytes to the surface of the SiCWs and magnetic nanoparticles. The anchored polyelectrolytes were polyacrylic acid (PAA) and poly(2-vinylpyridine) (P2VP). Next, the SiC/epoxy composites incorporating randomly oriented and magnetically oriented whiskers were fabricated. The formation of the composite was studied to determine the influence of the whiskers' surface composition on the epoxy curing reaction. After curing, the composites' thermal and thermo-mechanical properties were studied. These properties were related to the dispersion and orientation of the fillers in the composite samples. The obtained results indicated that the thermal and thermo-mechanical properties could be improved by orienting magnetically-active SiCWs inside the matrix. Silanization, "grafting to", adsorption, and complexation were used to modify

  13. Electron beam processed plasticized epoxy coatings for surface protection

    Energy Technology Data Exchange (ETDEWEB)

    Ibrahim, Mervat S. [National Center for Radiation Research and Technology, Nasr City (Egypt); Mohamed, Heba A., E-mail: hebaamohamed@gmail.com [National Research Center, Dokki (Egypt); Kandile, Nadia G. [University College for Girls, Ain Shams University (Egypt); Said, Hossam M.; Mohamed, Issa M. [National Center for Radiation Research and Technology, Nasr City (Egypt)

    2011-10-17

    Highlights: {center_dot} Coating formulations with EA 70%, HD 20%, and castor oil 10% under 1 Mrad pass{sup -1} irradiation dose showed the best adhesion and passed bending tests. {center_dot} The prepared EP-SF-An adduct improve anti-corrosion properties of coatings without any significant effect on physical, mechanical and chemical properties of the cured film. The optimum amount of aniline adduct as corrosion inhibitor was found to be 0.4 g for 100 g of coating formulation. {center_dot} The corrosion inhibition efficiency of the prepared adduct competed the commercial efficiency. - Abstract: Epoxy acrylate oligomer (EA) was plasticized by adding different plasticizers such as epoxidized soybean oil, glycerol and castor oil and cured by electron beam (EB). Different irradiation doses (1, 2.5 and 5 Mrad pass{sup -1}) were used in the curing process. The effect of both different irradiation doses and plasticizers on the end use performance properties of epoxy acrylate coating namely, pencil hardness, bending test, adhesion test, acid and alkali resistance test were studied. It was observed that incorporation of castor oil in epoxy acrylate diluted by 1,6-hexanediol diacrylate (HD) monomer with a ratio (EA 70%, HD 20%, castor oil 10%) under 1 Mrad pass{sup -1} irradiation dose improved the physical, chemical and mechanical properties of cured films than the other plasticizer. Sunflower free fatty acid was epoxidized in situ under well established conditions. The epoxidized sunflower free fatty acids (ESFA) were subjected to react with aniline in sealed ampoules under inert atmosphere at 140 deg. C. The produced adducts were added at different concentrations to epoxy acrylate coatings under certain EB irradiation dose and then evaluated as corrosion inhibitors for carbon steel surfaces in terms of weight loss measurements and corrosion resistance tests. It was found that, addition of 0.4 g of aniline adduct to 100 g epoxy acrylate formula may give the best corrosion

  14. Barium ferrite/epoxy resin nanocomposite system: Fabrication, dielectric, magnetic and hydration studies

    Directory of Open Access Journals (Sweden)

    A. Kanapitsas

    2016-03-01

    Full Text Available Composite systems of epoxy resin and barium ferrite nanoparticles have been prepared, and studied varying the content of the inclusions. Morphology of prepared samples has been examined via scanning electron microscopy and X-ray diffraction spectra, while electrical and magnetic properties were investigated by means of broadband dielectric spectroscopy, and magnetization tests respectively. Finally, water vapor sorption measurements were conducted in order to study the water sorption dynamics of the system. Electron microscopy images revealed the successful fabrication of nanocomposites. Dielectric permittivity increases with filler content, while three relaxation processes were detected in the relative spectra. These processes are attributed to interfacial polarization, glass to rubber transition of the matrix, and re-orientation of polar side groups of the polymer’s chain. Magnetization and magnetic saturation increase with magnetic nano-powder content. Nanocomposites absorb a small amount of water, not exceeding 1.7 wt%, regardless filler content, indicating their hydrophobic character.

  15. ANALISIS ARAH DAN PERLAKUAN SERAT TAPIS SERTA RASIO EPOXY HARDENER TERHADAP SIFAT FISIS DAN MEKANIS KOMPOSIT TAPIS/EPOXY

    Directory of Open Access Journals (Sweden)

    Putu Lokantara

    2012-11-01

    Full Text Available Tapis kelapa (Coconut filter as natural fiber, in this time its resources very copius but no longer be exploited and thrown off hand as waste though in fact its used for other material dissimilar inovatif and high economic valuable that is as one of natural fiber alternative to be composite. The objective of this research is to investigate the behavior changing of physical and mechanical properties of composite tapis kelapa as reinforcement and epoxy 7120 with hardener Versamid 140 as matrix. The fiber is treated with the chemical NaOH and KMnO4 with percentage 0.5%, 1%, and 2% in weight, respectively. The ratio of epoxy and hardener is 7:3 and 6:4, and fiber orientation 0o, 45o, dan 90o. For testing of the speciment in tensile test with ASTM standard D3039 and three point bending test with ASTM standard D790. The result of this research obtained that fiber treatment with KMnO4 give the better effect to machine properties compared to NaOH. Variation of percentage 0.5%, 1%, and 2% NaOH and KMnO4 give the effect in fiber surface which higher percentage make the cleaner of surface, decrease of wax contain, and roughness of fiber surface so that stronger of linkage of fiber and matrix and increase of tensile strength, bending strength, and bending modulus of the composite. The highest tensile strength, modulus of elasticity and bending strength are 70.23 MPa, 446.24 GPa and 97.81 MPa respectively reached at composite with ratio epoxy/hardener 7:3; by 2% KMnO4 and fiber orientation 45o. While the highest modulus of elasticity is 385.48 GPa reached at composite with the ratio epoxy/hardener 6:4; 2% KMnO4 and fiber orientation 90o. Keywords: Tensile Strength, bending strength, ratio of epoxy/hardener, NaOH, KMnO4

  16. Porous Epoxy: Effect of Mixing Sequences (ELH versus EHL Using Toluene as Extraction Medium via Ultrasonic Technique

    Directory of Open Access Journals (Sweden)

    Siti Noorkhartina Ishak

    2016-01-01

    Full Text Available Porous epoxy was fabricated using natural rubber latex (NRL as the void template. In this study, two mixing sequences were selected: epoxy, hardener, and then latex (EHL and epoxy, latex, and then hardener (ELH. The extraction process was carried out to extract the latex particles from the cured epoxy sample using toluene as extraction medium with ultrasonic technique for 1 hour. The formation of porous structure in epoxy system is dependent essentially on the amount of latex removed from the epoxy matrix. As expected, the density results showed lower values in the porous epoxy in ELH mixing sequences. More porous structure in epoxy was obtained which was proven by the increasing in porosity % which has led to lowering of the value in dielectric constant which is preferred for electronic packaging application. However, it also caused a decrease in flexural strength and modulus.

  17. Study on the Pulsed Flashover Characteristics of Solid-Solid Interface in Electrical Devices Poured by Epoxy Resin

    Science.gov (United States)

    Li, Manping; Wu, Kai; Yang, Zhanping; Ding, Man; Liu, Xin; Cheng, Yonghong

    2014-09-01

    In electrical devices poured by epoxy resin, there are a lot of interfaces between epoxy resin and other solid dielectrics, i.e. solid-solid interfaces. Experiments were carried out to study the flashover characteristics of two typical solid-solid interfaces (epoxy-ceramic and epoxy-PMMA) under steep high-voltage impulse for different electrode systems (coaxial electrodes and finger electrodes) and different types of epoxy resin (neat epoxy resin, polyether modified epoxy resin and polyurethane modified epoxy resin). Results showed that, the flashover of solid-solid interface is similar to the breakdown of solid dielectric, and there are unrecoverable carbonated tracks after flashover. Under the same distance of electrodes, the electric stress of coaxial electrodes is lower than that of finger electrodes; and after the flashover, there are more severe breakdown and larger enhanced surface conductivity at interface for coaxial electrodes, as compared with the case of finger electrode. The dielectric properties are also discussed.

  18. Study on the Pulsed Flashover Characteristics of Solid-Solid Interface in Electrical Devices Poured by Epoxy Resin

    International Nuclear Information System (INIS)

    Li Manping; Wu Kai; Ding Man; Liu Xin; Cheng Yonghong; Yang Zhanping

    2014-01-01

    In electrical devices poured by epoxy resin, there are a lot of interfaces between epoxy resin and other solid dielectrics, i.e. solid-solid interfaces. Experiments were carried out to study the flashover characteristics of two typical solid-solid interfaces (epoxy-ceramic and epoxy-PMMA) under steep high-voltage impulse for different electrode systems (coaxial electrodes and finger electrodes) and different types of epoxy resin (neat epoxy resin, polyether modified epoxy resin and polyurethane modified epoxy resin). Results showed that, the flashover of solid-solid interface is similar to the breakdown of solid dielectric, and there are unrecoverable carbonated tracks after flashover. Under the same distance of electrodes, the electric stress of coaxial electrodes is lower than that of finger electrodes; and after the flashover, there are more severe breakdown and larger enhanced surface conductivity at interface for coaxial electrodes, as compared with the case of finger electrode. The dielectric properties are also discussed. (plasma technology)

  19. In vitro Study on Apical Sealing Ability of Nano-Hydroxyapatite-Filled Epoxy Resin Based Endodontic Sealer

    Science.gov (United States)

    Masudi, S. M.; Luddin, N.; Mohamad, D.; Alkashakhshir, J. J.; Adnan, R.; Ramli, R. A.

    2010-03-01

    The objectives of this in vitro study were to evaluate the apical sealing ability of experimental nano hydroxyapatite (HA)-filled epoxy resin based endodontic sealer and to compare it with the commercial AH26 sealant. A total of 76 extracted human anterior teeth were instrumented using NiTi files and randomly divided into two groups of 33 teeth each and two control groups of 5 teeth each. The first group was obturated using gutta-percha with AH26 sealer. The second group was obturated with the nano HA-filled epoxy resin based sealer. All teeth were coated with nail polish except 2 mm from foramen apical and then suspended in 2% methylene blue for 7 days. All teeth were sectioned longitudinally for measuring penetration of the dye using stereo-microscope (x36). The result showed that there was no statistically significant difference (p>0.05) in apical sealing ability between AH26 silver-free sealer and nano HA sealer.

  20. Morphological Study on Room-Temperature-Cured PMMA-Grafted Natural Rubber-Toughened Epoxy/Layered Silicate Nanocomposite

    OpenAIRE

    Yuhana, N. Y.; Ahmad, S.; Kamal, M. R.; Jana, S. C.; Bahri, A. R. Shamsul

    2012-01-01

    A morphological study was conducted on ternary systems containing epoxy, PMMA-grafted natural rubber, and organic chemically modified montmorillonite (Cloisite 30B). Optical microscopy, transmission electron microscopy (TEM), scanning electron microscopy (SEM), energy dispersive X-ray (EDX), and wide-angle X-ray diffraction (WAXD) analysis were used. The following four materials were prepared at room temperature: cured unmodified epoxy, cured toughened epoxy, cured unmodified epoxy/Cloisite 3...

  1. Thermal properties of oil palm nano filler/kenaf reinforced epoxy hybrid nanocomposites

    Science.gov (United States)

    Saba, N.; Paridah, M. T.; Abdan, K.; Ibrahim, N. A.

    2016-11-01

    The aim of this research study was to fabricate nano oil palm empty fruit bunch (OPEFB)/kenaf/epoxy hybrid nanocomposites and to make comparative study on the thermal properties of nano OPEFB/kenaf/epoxy hybrid nanocomposites with the montmorillonite (MMT)/kenaf/epoxy hybrid nanocomposites and organically modified MMT (OMMT)/kenaf/epoxy hybrid nanocomposites. Epoxy based kenaf hybrid nanocomposites was prepared by dispersing the nano filler (nano OPEFB filler, MMT, OMMT) at 3% loading through high speed mechanical stirrer followed by hand lay-up technique. Thermal properties of hybrid nanocomposites were analyzed through thermogravimetry analyzer (TGA), and differential scanning calorimetry (DSC). Obtained results specified that addition of nano OPEFB filler improves the thermal stability and char yield of kenaf/epoxy composites. Furthermore, the increase in decomposition temperature by the nano OPEFB filler was quite comparable to the MMT/kenaf/epoxy but relatively less than OMMT/kenaf/epoxy hybrid nanocomposites. We concluded from overall consequences that the nano OPEFB filler can be used as the promising and innovative alternative of existing expensive nano filler, with relatively lesser impact on the environment having marked pronounced impact on the construction, automotive, aerospace, electronics and semiconducting sectors as future industries based on bio-wastes with satisfactory light weight and thermal stability on other side.

  2. Two cases of occupational allergic contact dermatitis from a cycloaliphatic epoxy resin in a neat oil

    DEFF Research Database (Denmark)

    Jensen, Charlotte D; Andersen, Klaus E

    2003-01-01

    to a neat oil used in metal processing. Patch testing revealed that the relevant contact allergen was a cycloaliphatic epoxy resin, 1,2-cyclohexanedicarboxylic acid, bis(oxiranylmethyl) ester, added to the oil as a stabilizer. None of the patients had positive reactions to the bisphenol A-based epoxy resin...... product is essential....

  3. Improvement in electrical, thermal and mechanical properties of epoxy by filling carbon nanotube

    Directory of Open Access Journals (Sweden)

    2008-01-01

    Full Text Available In this study, electrical, thermal and mechanical properties of multi-walled carbon nanotubes (CNTs reinforced Epon 862 epoxy have been evaluated. Firstly, 0.1, 0.2, 0.3, and 0.4 wt% CNT were infused into epoxy through a high intensity ultrasonic liquid processor and then mixed with EpiCure curing agent W using a high speed mechanical agitator. Electric conductivity, dynamic mechanical analysis (DMA, three point bending tests and fracture tests were then performed on unfilled, CNT-filled epoxy to identify the loading effect on the properties of materials. Experimental results show significant improvement in electric conductivity. The resistivity of epoxy decreased from 1014 Ω•m of neat epoxy to 10 Ω•m with 0.4% CNT. The experimental results also indicate that the frequency dependent behavior of CNT/epoxy nanocomposite can be modeled by R-C circuit, permittivity of material increase with increasing of CNT content. DMA studies revealed that filling the carbon nanotube into epoxy can produce a 90% enhancement in storage modulus and a 17°C increase in Tg. Mechanical test results showed that modulus increased with higher CNT loading percentages, but the 0.3 wt% CNT-infusion system showed the maximum strength and fracture toughness enhancement. The decrease in strength and fracture toughness in 0.4% CNT/epoxy was attributed to poor dispersions of nanotubes in the composite.

  4. High energy electron beam curing of epoxy resin systems incorporating cationic photoinitiators

    Science.gov (United States)

    Janke, Christopher J.; Lopata, Vincent J.; Havens, Stephen J.; Dorsey, George F.; Moulton, Richard J.

    1999-01-01

    A mixture of epoxy resins such as a semi-solid triglycidyl ether of tris (hydroxyphenyl) methane and a low viscosity bisphenol A glycidyl ether and a cationic photoinitiator such as a diaryliodonium salt is cured by irradiating with a dosage of electron beams from about 50 to about 150 kGy, forming a cross-linked epoxy resin polymer.

  5. Tribo-mechanical behaviour of SiC filled glass-epoxy composites at ...

    African Journals Online (AJOL)

    DR OKE

    reactivity, leading to superior friction properties. In this work an attempt was made to evaluate the mechanical properties and tribological behaviour of glass fabric reinforced- epoxy (G-E) composites and silicon carbide filled glass fabric reinforced-epoxy. (SiC-G-E) composites. The fabricated wear specimens were tested by ...

  6. Mechanical properties of polyethersulfone modified epoxy/3,3′-bis ...

    Indian Academy of Sciences (India)

    Wintec

    modified epoxy and bismaleimides incorporated poly- ethersulfone modified epoxy matrices were recorded on a. Perkin-Elmer (Model RX1) FT-IR Spectrometer. The tensile strength was determined using dog bone- shaped specimens according to ASTM-D3039, using an. Instron testing machine (Model 6025; Instron, UK), ...

  7. Hydrothermal ageing of glass/epoxy composites for wind turbine blades

    NARCIS (Netherlands)

    Rocha, I.B.C.M.; Raijmaekers, S.; Nijssen, R.P.L.; Van der Meer, F.P.

    2015-01-01

    In this work, a glass/epoxy material system commonly applied in wind turbine design was used to evaluate damage processes brought by water ingression during service life. Composite short-beams and neat epoxy beams and dog-bones were conditioned by water immersion at 50º until saturation and tested

  8. Effect of Hygrothermal Aging on the Mechanical Properties of Fluorinated and Nonfluorinated Clay-Epoxy Nanocomposites.

    Science.gov (United States)

    Hamim, Salah U; Singh, Raman P

    2014-01-01

    Hydrophilic nature of epoxy polymers can lead to both reversible and irreversible/permanent changes in epoxy upon moisture absorption. The permanent changes leading to the degradation of mechanical properties due to combined effect of moisture and elevated temperature on EPON 862, Nanomer I.28E, and Somasif MAE clay-epoxy nanocomposites are investigated in this study. The extent of permanent degradation on fracture and flexural properties due to the hygrothermal aging is determined by drying the epoxy and their clay-epoxy nanocomposites after moisture absorption. Significant permanent damage is observed for fracture toughness and flexural modulus, while the extent of permanent damage is less significant for flexural strength. It is also observed that permanent degradation in Somasif MAE clay-epoxy nanocomposites is higher compared to Nanomer I.28E clay-epoxy nanocomposites. Fourier transform infrared (FTIR) spectroscopy revealed that both clays retained their original chemical structure after the absorption-desorption cycle without undergoing significant changes. Scanning electron microscopy (SEM) images of the fracture surfaces provide evidence that Somasif MAE clay particles offered very little resistance to crack propagation in case of redried specimens when compared to Nanomer I.28E counterpart. The reason for the observed higher extent of permanent degradation in Somasif MAE clay-epoxy system has been attributed to the weakening of the filler-matrix interface.

  9. Modeling and mechanical performance of carbon nanotube/epoxy resin composites

    International Nuclear Information System (INIS)

    Srivastava, Vijay Kumar

    2012-01-01

    Highlights: ► The MWCNT fillers are uniformly dispersed in the epoxy resin, which improved the mechanical properties of epoxy resin. ► Modified Halpin–Tsai model is useful to calculate the Young’s modulus of MWCNT/epoxy resin composite. ► The experimental moduli are within the variation of 27% with the theoretical values. -- Abstract: The effect of multi-walled carbon nanotube (MWCNT) addition on mechanical properties of epoxy resin was investigated to obtain the tensile strength, compressive strength and Young’s modulus from load versus displacement graphs. The result shows that the tensile strength, compressive strength and Young’s modulus of epoxy resin were increased with the addition of MWCNT fillers. The significant improvements in tensile strength, compressive strength and Young’s modulus were obtained due to the excellent dispersion of MWCNT fillers in the epoxy resin. The dispersion of MWCNT fillers in epoxy resin was observed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM) analysis. Also, Halpin–Tsai model was modified by considering the average diameter of internal/external of multi-walled nanotube and orientation factor (α) to calculate the Young’s modulus of multi-walled carbon nanotubes (MWCNTs)/epoxy resin composite. There was a good correlation between the experimentally obtained Young’s modulus and modified Halpin–Tsai model.

  10. Flame Retardancy of Chemically Modified Lignin as Functional Additive to Epoxy Nanocomposites

    Science.gov (United States)

    John A. Howarter; Gamini P. Mendis; Alex N. Bruce; Jeffrey P. Youngblood; Mark A. Dietenberger; Laura Hasburgh

    2015-01-01

    Epoxy printed circuit boards are used in a variety of electronics applications as rigid, thermally stable substrates. Due to the propensity of components on the boards, such as batteries and interconnects, to fail and ignite the epoxy, flame retardant additives are required to minimize fire risk. Currently, industry uses brominated flame retardants, such as TBBPA, to...

  11. The influence of stiffeners on axial crushing of glass-fabric-reinforced epoxy composite shells

    Directory of Open Access Journals (Sweden)

    A. Vasanthanathan

    2017-01-01

    Full Text Available A generic static and impact experimental procedure has been developed in this work aimed at improving the stability of glass fabric reinforced epoxy shell structures by bonding with axial stiffeners. Crashworthy structures fabricated from composite laminate with stiffeners would offer energy absorption superior to metallic structures under compressive loading situations. An experimental material characterisation of the glass fabric reinforced epoxy composite under uni-axial tension has been carried out in this study. This work provides a numerical simulation procedure to describe the static and dynamic response of unstiffened glass fabric reinforced epoxy composite shell (without stiffeners and stiffened glass fabric reinforced epoxy composite shell (with axial stiffeners under static and impact loading using the Finite Element Method. The finite element calculation for the present study was made with ANSYS®-LS-DYNA® software. Based upon the experimental and numerical investigations, it has been asserted that glass fabric reinforced epoxy shells stiffened with GFRP stiffeners are better than unstiffened glass fabric reinforced epoxy shell and glass fabric reinforced epoxy shell stiffened with aluminium stiffeners. The failure surfaces of the glass fabric reinforced epoxy composite shell structures tested under impact were examined by SEM.

  12. Impact Damage In Carbon/Epoxy And Carbon/PEEK Composites

    Science.gov (United States)

    Nettles, A. T.; Magold, N. J.

    1991-01-01

    Report describes results of drop-weight impact testing of specimens of carbon-fiber/epoxy and carbon-fiber/polyetheretherketone (PEEK) composite materials. Panels made of these materials assembled into lightweight, strong, stiff structures useful in automobiles, aircraft, sporting goods, and many other products. PEEK specimens showed less delamination than epoxy specimens at given impact energy.

  13. Design and analysis of MEMS MWCNT/epoxy strain sensor using ...

    Indian Academy of Sciences (India)

    2017-06-20

    Jun 20, 2017 ... Home; Journals; Pramana – Journal of Physics; Volume 89; Issue 1. Design and analysis of MEMS MWCNT/epoxy strain sensor using COMSOL. GAURAV ... The design and performance of piezoresistive MEMS-based MWCNT/epoxy composite strain sensor using COMSOL Multiphysics Toolbox has been ...

  14. Thermal and mechanical interfacial properties of epoxy composites based on functionalized carbon nanotubes

    International Nuclear Information System (INIS)

    Jin Fanlong; Ma Changjie; Park, Soo-Jin

    2011-01-01

    Highlights: → CNTs were functionalized by acid and amine treatments. → Epoxy resin/CNT composites were prepared. → T g of the composites increased by about 10 deg. C compared to neat epoxy resins. → Toughness of the composites was significantly improved by the addition of functionalized CNTs. - Abstract: Carbon nanotubes (CNTs) were treated by a mixture of acid and functionalized subsequently by amine treatment to improve interfacial interactions and dispersion of CNTs in epoxy matrix. The thermal stabilities and mechanical interfacial properties of epoxy/CNT composites were investigated using several techniques. The dispersion state of CNTs in the epoxy matrix was observed by scanning electron microscope (SEM) and transmission electron microscopy (TEM). As a result, the glass transition temperature of epoxy/CNT composites increased by about 11 deg. C compared to neat epoxy resins. The mechanical interfacial property of the composites was significantly increased by the addition of amine treated CNTs. The SEM and TEM results showed that the separation and uniform dispersion of CNTs in the epoxy matrix.

  15. Evaluation of epoxy compounds as a material for patching and protecting concrete : final report.

    Science.gov (United States)

    1971-01-01

    The final report summarizes the results of a study of the use of epoxy compounds in the shallow surface repair and sealing of concrete bridge decks. The research effort concentrated on the use of epoxy resin systems as bonded overlays and included ev...

  16. Novel phosphorus containing epoxy networks based on trihydrocarbyl phosphine oxides having active substituents

    OpenAIRE

    1990-01-01

    Epoxy resins can be cured or crosslinked with trihydrocarbyl phosphine oxide compounds having epoxy-reactive (active hydrogen) substituents either alone or in combination with amine-terminated polyarylene ethers (e.g., amine-terminated polysulfone oligomers or high polymers.

  17. Study of molecular iodine-epoxy paint mass transfer

    Energy Technology Data Exchange (ETDEWEB)

    Belval-Haltier, E. [Inst. de Protection et Surete Nucleaire, IPSN, CEN Cadarache, St. Paul-lez-Durance (France)

    1996-12-01

    The mass transfer phenomena may have a significant influence on the quantity of I{sub 2} which could be released following a severe accident of a nuclear power plant and specially the mass transfer of iodine onto containment surfaces. So, the objective of the present work was to evaluate which phase limited the adsorption process of iodine onto gaseous epoxy paint under a range of conditions which may be relevant to a severe reactor accident. In this aim, a series of experiments was conducted in which the sorption kinetics of molecular iodine, labelled with {sup 131}I, was measured by monitoring continuously the accumulation of this species on the epoxy surface. For each test condition, the initial deposition velocity was determined and the corresponding gas phase mass transfer, kg, was estimated by using the heat transfer analogy for a laminar flow passing over a flat plate. Then, the surface reaction rate, Kr, was deduced from these two values. Experiments performed indicated that iodine adsorption onto epoxy paint is highly dependent on temperature, relative humidity of the carrier gas and moisture content of the painted coupon. In dry air flow conditions, the adsorption of iodine onto paint was found to increase with temperature and to be limited by the surface reaction rate, Kr. The I{sub 2} adsorption rate was found to increase with the humidity of carrier gas and in some studied conditions, the initial deposition velocity appeared to be controlled by gas phase mass transfer rather than surface interaction. The same phenomenon has been observed with an increase of the initial water content of the painted coupon. (author) 6 figs., 1 tab., 8 refs.

  18. Fracture Behavior of Silica- and Rubber-Nanoparticle-Toughed Epoxies

    Science.gov (United States)

    Labak, Amelia K.

    Particle-toughened crosslinked epoxies are popular materials for a variety of applications, including the microelectronics industry. For this application, the properties of these materials, such as a high fracture toughness and a low coefficient of thermal expansion, are highly appealing. In order to achieve these properties, inorganic particles are often added into the matrix. For this study, both inorganic and organic particles-toughened epoxies are investigated in the hopes of finding an optimized system. In particular, in this study, micron-sized silica and nano-sized rubbery block copolymers are added to an amine-cured epoxy matrix. A series of rubber-only and silica-only systems are investigated for their contribution to the fracture toughness. Then, a series of hybrid systems are investigated. The hypothesis is that the rubber will contribute toughness through rubber particle cavitation and matrix void growth and the silica will contribute toughness through crack pinning and bridging and particle debonding. In the hybrid systems, these mechanisms will take place at a different scale. Therefore, the nanoscale mechanisms of the rubber will be able to function at the same time as the micron sized mechanisms of the silica and the resultant toughness will be synergistically higher. The results from this study show an interesting contribution from the rubber particles both in the rubber-only systems and the hybrid system. Ultimately, there was a marked increase in the fracture toughness of the hybrid systems, although not synergistic. This increase indicates that it would be possible to create an optimized hybrid system from the combined addition of these particles.

  19. Thermomechanical properties of shape-memory hydro-epoxy resin

    International Nuclear Information System (INIS)

    Wei, Kun; Zhu, Guangming; Tang, Yusheng; Tian, Guangming; Xie, Jianqiang

    2012-01-01

    The thermomechanical properties and shape-memory performance of a novel shape-memory hydro-epoxy resin system are studied. The system is prepared using hydro-epoxy, maleic anhydride, and poly(propylene glycol) diglycidyl ether (PPGDGE). The glass transition temperature (T g ) is determined using dynamic mechanical analysis, and the results indicate that T g linearly decreases from 124 to 60 °C as the PPGDGE content increases. The tensile strength drastically increases after the addition of PPGDGE but gradually decreases as the PPGDGE content continues to increase. The room-temperature bend strength decreases as the PPGDGE content increases but increases slightly and then continues to decrease when the PPGDGE content is increased to 6.67 mol%. Moreover, the room-temperature elongation at break increases as the PPGDGE content increases but decreases slightly and then continues to increase when the PPGDGE content is increased to 6.67 mol%. These phenomena are attributed to flexible segment crystallization, which increases the rigidity of hydro-epoxy resin. Finally, investigation of shape-memory behavior of the resin reveals that full recovery can be observed after only a few minutes when the temperature is equal to or above T g . The shape recovery time first increases and then decreases as the PPGDGE content is increased at T g , T g + 10 °C, and T g + 20 °C, showing a polymer peak value at 6.67 mol% PPGDGE content. These results are attributed to the increase in PPGDGE content. (paper)

  20. Evaluation of epoxy resin for cryogenic use by positron annihilation method. Change of characteristics of epoxy resin with cross-linking density and positron lifetime

    International Nuclear Information System (INIS)

    Nishijima, Shigehiro; Honda, Yoshihide; Okada, Toichi; Kobayashi, Yoshinori; Namba, Shingo.

    1994-01-01

    The positron annihilation method has been applied to evaluate unoccupied space in epoxy aiming at the design of the molecular structure for cryogenic use. To confirm the model in which molecular free space is needed in the epoxy for cryogenic use, the molecular weight between cross-linkings in epoxy was changed. The increase of molecular weight between cross-linkings brought an increase of fracture toughness even at liquid helium temperature and the model was found to be confirmed. The increase of molecular weight between cross-linkings was also found to decrease the 3rd lifetime of positrons. It suggested that the epoxy main chains were folded and this was confirmed by the molecular mechanical calculation. (author)

  1. The influence of interfaces and water uptake on the dielectric response of epoxy-cubic boron nitride composites

    NARCIS (Netherlands)

    Tsekmes, I.A.; Morshuis, P.H.F.; Smit, J.J.; Kochetov, R.

    2015-01-01

    In this study, epoxy-cubic boron nitride composites are fabricated, and their dielectric response is investigated. They exhibit the same trend as epoxy composites reinforced with other filler types. Thus, at low filler concentrations, they exhibit a lower relative permittivity than neat epoxy. As

  2. 21 CFR 177.2280 - 4,4′-Isopropyl-idenedi-phenol-epichloro-hydrin thermo-setting epoxy resins.

    Science.gov (United States)

    2010-04-01

    ... thermo-setting epoxy resins. 177.2280 Section 177.2280 Food and Drugs FOOD AND DRUG ADMINISTRATION...,4′-Isopropyl-idenedi-phenol-epichloro-hydrin thermo-setting epoxy resins. 4,4′-Isopropylidenediphenol-epichlo-rohydrin thermosetting epoxy resins may be safely used as articles or components of...

  3. 21 CFR 175.380 - Xylene-formaldehyde resins condensed with 4,4′-isopropylidenediphenol-epichlorohydrin epoxy resins.

    Science.gov (United States)

    2010-04-01

    ...-isopropylidenediphenol-epichlorohydrin epoxy resins. 175.380 Section 175.380 Food and Drugs FOOD AND DRUG ADMINISTRATION... Xylene-formaldehyde resins condensed with 4,4′-isopropylidenediphenol-epichlorohydrin epoxy resins. The...′-isopropylidenediphenol-epichlorohydrin epoxy resins, to which may have been added certain optional adjuvant substances...

  4. New chemically reworkable epoxy coatings obtained by the addition of polyesters with star topologies to diglycidyl ether of bisphenol A resins

    OpenAIRE

    Serra, A.; Ferrando, F.; Fernández-Francos, X.; Ramis, X.; Tomuta, A.M.

    2013-01-01

    A new multiarm star with hyperbranched aromatic–aliphatic polyester core and poly(ɛ-caprolactone) arms (HBPCL) was synthesized and characterized. Mixtures of diglycidyl ether of bisphenol A (DGEBA) resin and different proportions of this star type modifier were cured using a thermal cationic curing agent, Yb(OTf)3. The HBPCL prepared has hydroxyl groups as chain ends, which are capable of chemically incorporating to the epoxy matrix by means of the monomer activated mechanism. This, together ...

  5. Novel Epoxy Activated Hydrogels for Solving Lactose Intolerance

    OpenAIRE

    Elnashar, Magdy M. M.; Hassan, Mohamed E.

    2014-01-01

    “Lactose intolerance” is a medical problem for almost 70% of the world population. Milk and dairy products contain 5–10% w/v lactose. Hydrolysis of lactose by immobilized lactase is an industrial solution. In this work, we succeeded to increase the lactase loading capacity to more than 3-fold to 36.3 U/g gel using epoxy activated hydrogels compared to 11 U/g gel using aldehyde activated carrageenan. The hydrogel's mode of interaction was proven by FTIR, DSC, and TGA. The high activity of the ...

  6. Moisture diffusion parameter characteristics for epoxy composites and neat resins

    Science.gov (United States)

    Long, E. R., Jr.

    1979-01-01

    The moisture absorption characteristics of two graphite/epoxy composites and their corresponding cured neat resins were studied in high humidity and water immersion environments at elevated temperatures. Moisture absorption parameters, such as equilibrium moisture content and diffusion coefficient derived from data taken on samples exposed to high humidity and water soak environments, were compared. Composite swelling in a water immersion environment was measured. Tensile strengths of cured neat resin were measured as a function of their equilibrium moisture content after exposure to different moisture environments. The effects of intermittent moderate tensile loads on the moisture absorption parameters of composite and cured neat resin samples were determined.

  7. Los morteros epoxi en la construcción

    Directory of Open Access Journals (Sweden)

    Fernández Cánovas, Manuel

    1968-02-01

    Full Text Available Epoxi resins are being increasingly applied in construction in recent years. This is due to their excellent properties and an improving technology, which enables these resins to be applied to more delicate and difficult uses. This article describes the work done by the author as part of an extensive program of experimental work at the Instituto Eduardo Torroja laboratory. This program of work refers particularly to mortars with a low content of epoxi resins. By this is meant a mixture of none fine aggregate with the least quantity of resin necessary to obtain a suitable bond. The investigation involved a study of the proportioning of sand and resin, the relation between proportioning, the age and the mechanical strength and also the physical properties of the resulting mortars.Desde hace unos años las resinas epoxi están encontrando una mayor aplicación en el campo de la construcción. Esto es debido a sus excelentes propiedades y a una tecnología cada vez más perfeccionada, las cuales permiten realizar, con éxito, muchas de sus aplicaciones a problemas cada día más difíciles y delicados. El autor da cuenta, en este artículo, de los trabajos que ha realizado sobre morteros epoxi como parte de un amplio plan de ensayos experimentales que el Instituto Eduardo Torroja lleva a cabo en sus laboratorios. Este estudio se refiere a los morteros epoxídicos pobres, entendiéndose por tales, la mezcla de árido exento de finos con la mínima cantidad de resina precisa para su confección. En el mismo se estudian las influencias de: la granulometría de la arena en la cantidad de resina a emplear; de la dosificación y de la edad en la resistencia mecánica, así como de las propiedades físicas de los morteros así formados.

  8. Debonding of epoxy from glass in irradiated laminates

    International Nuclear Information System (INIS)

    Klabunde, C.E.; Coltman, R.R. Jr.

    1982-01-01

    Glass-fabric-filled epoxies irradiated at 4.7 K and examined at room temperature by 20x stereomicroscopy showed an internal flaw structure which increasingly filled the sample as the γ-dose was increased. These flaws were determined to be areas where the plastic had debonded from the glass fibers. The extent of this process correlated well with the dose-dependent loss of mechanical strength. Evidence is reported for a similar mechanism in polyimides although visible flaws have not yet been produced. Possible mechanisms for debonding are suggested. New experiments are also suggested to clarify further the failure mechanism

  9. Visualization of impact damaging of carbon/epoxy panels

    Science.gov (United States)

    Boccardi, Simone; Boffa, Natalino Daniele; Carlomagno, Giovanni Maria; Meola, Carosena; Ricci, Fabrizio

    2016-05-01

    This work is concerned with impact damaging of carbon/epoxy materials. Specimens of different thickness are herein considered, which involve several fibers orientations and stacking sequences. Impact tests are carried out at different energies with a modified Charpy pendulum. The specimen surface opposite to that struck by the impactor is viewed by an infrared imaging device. Then, a sequence of thermal images is acquired during each impact test. Through the temperature variations experienced by the specimen surface, post-processing of such images supplies the likely occurred damage. In addition, specimens are non-destructively evaluated with lock-in thermography to visualize any manufacturing defects, as well as impact damage.

  10. Synthesis and properties of epoxy-phenolic clay nanocomposites

    Directory of Open Access Journals (Sweden)

    2007-09-01

    Full Text Available An epoxy-phenolic resin suitable for use as a composite matrix was reinforced with modified nanoclay (montmorillonite type. Characterization by x-ray diffraction and transmission electron microscopy (TEM demonstrated that intercalated nanocomposites were formed with an inter-gallery distance of approximately 10 nm. The influence of nanoparticles on tensile strength and modulus, fracture toughness, and impact toughness was measured and compared with the unreinforced polymer. The results revealed that the maximum enhancement in stiffness and toughness was achieved with 2.5 wt% filler content. The enhancement in toughness behavior was attributed to the activation of multiple energy-dissipating damage mechanisms in the nanocomposites.

  11. Lateral impact on pressurized glass/epoxy pipes

    Energy Technology Data Exchange (ETDEWEB)

    Santiago, Rafael C.; Alves, Marcilio [Universidade de Sao Paulo (USP), SP (Brazil). Escola Politecnica], e-mail: rafael.santiago@poli.usp.br, e-mail: maralves@usp.br

    2009-07-01

    This work studies the impact of a drop mass against glass/epoxy composite pipes. The experimental tests comprises an impact hammer and the set-up is such that a drop mass falls transversally to the main length of the tube. The impact response is measured with a non-contact laser system and reveals some issues explored here in a numerical model. Inner pressure was applied to the tube in order to access its influence on failure. It has been found that the numerical model represents well the structural collapse of a pressurized pipe under a lateral impact. (author)

  12. Development of epoxy resin-type neutron shielding materials (I)

    International Nuclear Information System (INIS)

    Cho, Soo Haeng; Kim, Ik Soo; Shin, Young Joon; Do, Jae Bum; Ro, Seung Gy.

    1997-12-01

    Because the exposure to radiation in the nuclear facilities can be fatal to human, it is important to reduce the radiation dose level to a tolerable level. The purpose of this study is to develop highly effective neutron shielding materials for the shipping and storage cask of radioactive materials or in the nuclear /radiation facilities. On this study, we developed epoxy resin based neutron shielding materials and their various materials properties, including neutron shielding ability, fire resistance, combustion characteristics, radiation resistance, thermal and mechanical properties were evaluated experimentally. (author). 31 refs., 22 tabs., 17 figs

  13. Modified silyl-terminated polyether polymer blends with bisphenol A diglycidyl ether epoxy for adhesive applications

    International Nuclear Information System (INIS)

    Bitenieks, J; Meri, R Merijs; Zicans, J; Berzins, R; Umbraško, J; Rekners, U

    2016-01-01

    Modified silyl-terminated polyether polymer (MS Polymer) was blended with bisphenol A diglycidyl ether (DGEBPA) epoxy at MS Polymer/epoxy ratio from 30/70 to 70/30. MS Polymer/epoxy systems were examined for two-component adhesive formulation with additional fillers. Applicability of the MS Polymer/epoxy system at the ratio of the components 60/40 is demonstrated for the development of adhesive formulation. Rheological analysis of the components A and B shows suitable viscosity values for development of two- component adhesives formulation. Curing dynamics as well as tensile stress-strain properties and Shore A hardness of the chosen adhesive formulation are reasonable for the development of MS Polymer/epoxy type adhesive. (paper)

  14. Static and Dynamic Mechanical Properties of Graphene Oxide-Incorporated Woven Carbon Fiber/Epoxy Composite

    Science.gov (United States)

    Adak, Nitai Chandra; Chhetri, Suman; Kim, Nam Hoon; Murmu, Naresh Chandra; Samanta, Pranab; Kuila, Tapas

    2018-01-01

    This study investigates the synergistic effects of graphene oxide (GO) on the woven carbon fiber (CF)-reinforced epoxy composites. The GO nanofiller was incorporated into the epoxy resin with variations in the content, and the CF/epoxy composites were manufactured using a vacuum-assisted resin transfer molding process and then cured at 70 and 120 °C. An analysis of the mechanical properties of the GO (0.2 wt.%)/CF/epoxy composites showed an improvement in the tensile strength, Young's modulus, toughness, flexural strength and flexural modulus by 34, 20, 83, 55 and 31%, respectively, when compared to the CF/epoxy composite. The dynamic mechanical analysis of the composites exhibited an enhancement of 56, 114 and 22% in the storage modulus, loss modulus and damping capacity (tanδ), respectively, at its glass transition temperature. The fiber-matrix interaction was studied using a Cole-Cole plot analysis.

  15. Synthetic Applications of Chiral Unsaturated Epoxy Alcohols Prepared by Sharpless Asymmetric Epoxidation

    Directory of Open Access Journals (Sweden)

    María Moreno

    2010-02-01

    Full Text Available An overview of the synthesis and applications of chiral 2,3-epoxy alcohols containing unsaturated chains is presented. One of the fundamental synthetic routes to these compounds is Sharpless asymmetric epoxidation, which is reliable, highly chemoselective and enables easy prediction of the product enantioselectivity. Thus, unsaturated epoxy alcohols are readily obtained by selective oxidation of the allylic double bond in the presence of other carbon-carbon double or triple bonds. The wide availability of epoxy alcohols with unsaturated chains, the versatility of the epoxy alcohol functionality (e.g. regio- and stereo-selective ring opening; oxidation; and reduction, and the arsenal of established alkene chemistries, make unsaturated epoxy alcohols powerful starting materials for the synthesis of complex targets such as biologically active molecules. The popularization of ring-closing metathesis has further increased their value, making them excellent precursors to cyclic compounds.

  16. Exploring biomass based carbon black as filler in epoxy composites: Flexural and thermal properties

    International Nuclear Information System (INIS)

    Abdul Khalil, H.P.S.; Firoozian, P.; Bakare, I.O.; Akil, Hazizan Md.; Noor, Ahmad Md.

    2010-01-01

    Carbon blacks (CB), derived from bamboo stem (BS-CB), coconut shells (CNS-CB) and oil palm empty fiber bunch (EFB-CB), were obtained by pyrolysis of fibers at 700 o C, characterized and used as filler in epoxy composites. The results obtained showed that the prepared carbon black possessed well-developed porosities and are predominantly made up of micropores. The BS-CB, CNS-CB and EFB-CB filled composites were prepared and characterized using scanning electron microscope (SEM) and thermogravimetric analyzer (TGA). The SEM showed that the fractured surface of the composite indicates its high resistance to fracture. The CBs-epoxy composites exhibited better flexural properties than the neat epoxy, which was attributed to better adhesion between the CBs and the epoxy resin. TGA showed that there was improvement in thermal stability of the carbon black filled composites compared to the neat epoxy resin.

  17. The Effect of Water on the Work of Adhesion at Epoxy Interfaces by Molecular Dynamics Simulation

    Science.gov (United States)

    Hinkley, J.A.; Frankland, S.J.V.; Clancy, T.C.

    2009-01-01

    Molecular dynamics simulation can be used to explore the detailed effects of chemistry on properties of materials. In this paper, two different epoxies found in aerospace resins are modeled using molecular dynamics. The first material, an amine-cured tetrafunctional epoxy, represents a composite matrix resin, while the second represents a 177 C-cured adhesive. Surface energies are derived for both epoxies and the work of adhesion values calculated for the epoxy/epoxy interfaces agree with experiment. Adding water -- to simulate the effect of moisture exposure -- reduced the work of adhesion in one case, and increased it in the other. To explore the difference, the various energy terms that make up the net work of adhesion were compared and the location of the added water was examined.

  18. Preparation and Properties Study of Thermally Conductive Epoxy/Modified Boron Nitride/Graphene Nanosheets Composites

    Science.gov (United States)

    Chen, Hexiang; Zhao, Chunbao; Xu, Suichun; Yang, Xujie

    2017-12-01

    A series of thermally conductive and electric-insulating epoxy composites filled with boron nitride (BN) modified by octadecyl trimethyl ammonium bromide and graphene nanosheets (GNP) were prepared. The effects of modified-BN (BNOTAB) and GNP content on thermal conductivity, electric-insulating and thermal stability properties of epoxy composite were investigated. The results indicate that the BNOTAB can homogeneously disperse into epoxy system. When the mass ratio of BNOTAB/GNP is 6:4 (total filler content is 10%), the thermal conductivity of the composites reached 0.48 W/(m·K), which is 108.7% higher than that of the neat epoxy. Meanwhile, the composite retains excellent electric-insulating property. TGA and DSC results showed that the addition of BNOTAB/GNP filler particles can improve the thermal stability of epoxy resin composites.

  19. Electrical and Mechanical Properties of 3D-Printed Graphene-Reinforced Epoxy

    Science.gov (United States)

    Compton, Brett G.; Hmeidat, Nadim S.; Pack, Robert C.; Heres, Maximilian F.; Sangoro, Joshua R.

    2018-03-01

    Recent developments in additive manufacturing have demonstrated the potential for thermoset polymer feedstock materials to achieve high strength, stiffness, and functionality through incorporation of structural and functional filler materials. In this work, graphene was investigated as a potential filler material to provide rheological properties necessary for direct-write three-dimensional (3D) printing and electrostatic discharge properties to the printed component. The rheological properties of epoxy/graphene mixtures were characterized, and printable epoxy/graphene inks formulated. Sheet resistance values for printed epoxy/graphene composites ranged from 0.67 × 102 Ω/sq to 8.2 × 103 Ω/sq. The flexural strength of printed epoxy/graphene composites was comparable to that of cast neat epoxy ( 80 MPa), suggesting great potential for these new materials in multifunctional 3D-printed devices.

  20. Electrical and Mechanical Properties of 3D-Printed Graphene-Reinforced Epoxy

    Science.gov (United States)

    Compton, Brett G.; Hmeidat, Nadim S.; Pack, Robert C.; Heres, Maximilian F.; Sangoro, Joshua R.

    2017-12-01

    Recent developments in additive manufacturing have demonstrated the potential for thermoset polymer feedstock materials to achieve high strength, stiffness, and functionality through incorporation of structural and functional filler materials. In this work, graphene was investigated as a potential filler material to provide rheological properties necessary for direct-write three-dimensional (3D) printing and electrostatic discharge properties to the printed component. The rheological properties of epoxy/graphene mixtures were characterized, and printable epoxy/graphene inks formulated. Sheet resistance values for printed epoxy/graphene composites ranged from 0.67 × 102 Ω/sq to 8.2 × 103 Ω/sq. The flexural strength of printed epoxy/graphene composites was comparable to that of cast neat epoxy ( 80 MPa), suggesting great potential for these new materials in multifunctional 3D-printed devices.

  1. The effects of MWNT on thermal conductivity and thermal mechanical properties of epoxy

    Science.gov (United States)

    Ismadi, A. I.; Othman, R. N.

    2017-12-01

    Multiwall nanotube (MWNT) was used as filler in various studies to improve thermal conductivity and mechanical properties of epoxy. Present study varied different weight loading (0, 0.1 %, 0.5 %, 1 %, 1.5 %, 3 % and 5 %) of MWNT in order to observe the effects on the epoxy. Nanocomposite was analyzed by dynamic-mechanical thermal analyser (DMTA) and KD2 pro analyzer. DMTA measured storage modulus (E') and glass transition temperature (Tg) of the nanocomposite. Result showed that Tg value of neat epoxy is higher than all MWNT epoxy nanocomposite. Tg values drop from 81.55 °C (neat epoxy) to 65.03 °C (at 0.1 wt%). This may happen due to the agglomeration of MWNT in the epoxy. However, Tg values increases with the increase of MWNT wt%. Tg values increased from 65.03 °C to 78.53 °C at 1 wt%. Increment of storage modulus (E') at 3 °C (glassy region) was observed as the MWNT loading increases. Maximum value of E' during glassy region was observed to be at 5 wt% with (7.26±0.7) E+08 Pa compared to neat epoxy. On the contrary, there is slight increased and slight decreased with E' values at 100 °C (rubbery region) for all nanocomposite. Since epoxy exhibits low thermal conductivity properties, addition of MWNT has enhanced the properties. Optimum value of thermal conductivity was observed at 3 wt%. The values increased up to 9.03 % compared to neat epoxy. As expected, the result showed decrease value in thermal conductivity at 5 wt% as a result of agglomeration of MWNT in the epoxy.

  2. Evaluation of Nanomaterial Approaches to Damping in Epoxy Resin and Carbon Fiber/Epoxy Composite Structures by Dynamic Mechanical Analysis

    Science.gov (United States)

    Miller, G.; Heimann, Paula J.; Scheiman, Daniel A.; Duffy, Kirsten P.; Johnston, J. Chris; Roberts, Gary D.

    2013-01-01

    Vibration mitigation in composite structures has been demonstrated through widely varying methods which include both active and passive damping. Recently, nanomaterials have been investigated as a viable approach to composite vibration damping due to the large surface available to generate energy dissipation through friction. This work evaluates the influence of dispersed nanoparticles on the damping ratio of an epoxy matrix. Limited benefit was observed through dispersion methods, however nanoparticle application as a coating resulting in up to a three-fold increase in damping.

  3. Laser decontamination of epoxy painted concrete surfaces in nuclear plants

    Science.gov (United States)

    Anthofer, A.; Lippmann, W.; Hurtado, A.

    2014-04-01

    Laser technology offers an efficient decontamination of surfaces contaminated by polychlorinated biphenyls (PCB) by precise application of highly focused laser beam power. In the context of nuclear decommissioning all walls and floors of a reactor building have to be cleaned from chemical-toxic substances. State of the art is a manual and mechanic ablation and a subsequent treatment in a hazardous waste incinerator. In this study, alternatively, a laser-based system exhibiting, decontamination rates of up to 6.4 m2/h has been operated using a 10 kW diode laser in continuous wave (CW) mode with a spot size of 45×10 mm2 and a wavelength of 980-1030 nm. The system allows a rapid heating of the surfaces up to temperatures of more than 1000 °C leading to ablation and thermal decomposition of PCB in one process step. Thermal quenching prevents formation of polychlorinated dioxines (PCDD) and polychlorinate furans (PCDF) in the flue gas. Additionally, an in situ measurement system based on laser induced fluorescence (LIF) is developed to monitor the thermal decomposition of PCB. For initial experiments samples covered with epoxy paint were used to evaluate the process and to carry out finite element based simulations. In this paper, experimental results of ablation tests by laser irradiation of epoxy painted concrete are presented and discussed.

  4. Thermoviscoelastic shape memory behavior for epoxy-shape memory polymer

    International Nuclear Information System (INIS)

    Chen, Jianguo; Liu, Liwu; Liu, Yanju; Leng, Jinsong

    2014-01-01

    There are various applications for shape memory polymer (SMP) in the smart materials and structures field due to its large recoverable strain and controllable driving method. The mechanical shape memory deformation mechanism is so obscure that many samples and test schemes have to be tried in order to verify a final design proposal for a smart structure system. This paper proposes a simple and very useful method to unambiguously analyze the thermoviscoelastic shape memory behavior of SMP smart structures. First, experiments under different temperature and loading conditions are performed to characterize the large deformation and thermoviscoelastic behavior of epoxy-SMP. Then, a rheological constitutive model, which is composed of a revised standard linear solid (SLS) element and a thermal expansion element, is proposed for epoxy-SMP. The thermomechanical coupling effect and nonlinear viscous flowing rules are considered in the model. Then, the model is used to predict the measured rubbery and time-dependent response of the material, and different thermomechanical loading histories are adopted to verify the shape memory behavior of the model. The results of the calculation agree with experiments satisfactorily. The proposed shape memory model is practical for the design of SMP smart structures. (paper)

  5. Solid-state fractional capacitor using MWCNT-epoxy nanocomposite

    Science.gov (United States)

    John, Dina A.; Banerjee, Susanta; Bohannan, Gary W.; Biswas, Karabi

    2017-04-01

    Here, we propose the fabrication of a solid state fractional capacitor for which constant phase (CP) angles were attained in different frequency zones: 110 Hz-1.1 kHz, 10 kHz-118 kHz, and 230 kHz-20 MHz. The configuration makes use of epoxy resin as the matrix in which multi-walled carbon nanotubes (MWCNTs) are dispersed. Adhesive nature of the epoxy resin is utilized for binding the electrodes, which avoids the extra step for packaging. The fractional capacitive behavior is contributed by the distribution of time constants for the electron to travel from one electrode to the other. The distributive nature of the time constant is ensured by inserting a middle plate which is coated with a porous film of polymethyl-methacrylate in between the two electrodes. The phase angle trend for the configuration is studied in detail, and it is observed that as the % of carbon nanotubes (CNTs) loading increases, the CP angle increases from - 85 ° to - 45 ° in the frequency zones above 100 Hz. The developed device is compact and it can be easily integrated with the electronic circuits.

  6. Thermoviscoelastic characterization and prediction of Kevlar/epoxy composite laminates

    Science.gov (United States)

    Gramoll, K. C.; Dillard, D. A.; Brinson, H. F.

    1990-01-01

    The thermoviscoelastic characterization of Kevlar 49/Fiberite 7714A epoxy composite lamina and the development of a numerical procedure to predict the viscoelastic response of any general laminate constructed from the same material were studied. The four orthotropic material properties, S sub 11, S sub 12, S sub 22, and S sub 66, were characterized by 20 minute static creep tests on unidirectional (0) sub 8, (10) sub 8, and (90) sub 16 lamina specimens. The Time-Temperature Superposition-Principle (TTSP) was used successfully to accelerate the characterization process. A nonlinear constitutive model was developed to describe the stress dependent viscoelastic response for each of the material properties. A numerical procedure to predict long term laminate properties from lamina properties (obtained experimentally) was developed. Numerical instabilities and time constraints associated with viscoelastic numerical techniques were discussed and solved. The numerical procedure was incorporated into a user friendly microcomputer program called Viscoelastic Composite Analysis Program (VCAP), which is available for IBM PC type computers. The program was designed for ease of use. The final phase involved testing actual laminates constructed from the characterized material, Kevlar/epoxy, at various temperatures and load level for 4 to 5 weeks. These results were compared with the VCAP program predictions to verify the testing procedure and to check the numerical procedure used in the program. The actual tests and predictions agreed for all test cases which included 1, 2, 3, and 4 fiber direction laminates.

  7. Epoxy Resin Based Composites, Mechanical and Tribological Properties: A Review

    Directory of Open Access Journals (Sweden)

    S.A. Bello

    2015-12-01

    Full Text Available High fuel consumption by automobile and aerospace vehicles built from legacy alloys has been a great challenge to global design and material engineers. This has called for researches into material development for the production of lighter materials of the same or even superior mechanical properties to the existing materials in this area of applications. This forms a part of efforts to achieve the global vision 2025 i.e to reduce the fuel consumption by automobile and aerospace vehicles by at least 75 %. Many researchers have identified advanced composites as suitable materials in this regard. Among the common matrices used for the development of advanced composites, epoxy resin has attained a dominance among its counterparts because of its excellent properties including chemical, thermal and electrical resistance properties, mechanical properties and dimensional stability. This review is a reflection of the extensive study on the currently ongoing research aimed at development of epoxy resin hybrid nanocomposites for engineering applications. In this paper, brief explanation has been given to different terms related to the research work and also, some previous works (in accordance with materials within authors’ reach in the area of the ongoing research have been reported.

  8. Toughening mechanism in elastometer-modified epoxy resins: Part 1

    Science.gov (United States)

    Yee, A. F.; Pearson, R. A.

    1983-01-01

    Several plaques of Epon 828, cured with piperidine, modified with hycar(r) CTBN 1300X8, Hycar(R) CTBN 1300X13, and Hycar(R) CTBN 1300x15, and in some cases modified with biphenol A (BPA), yielded properly toughened epoxies with rubber particle diameters ranging from 0.1 to 10 microns. Fracture toughness experiments indicate that toughness was more a function of rubber content than the rubber particle size. Tensile volumetric behavior of the near resin exhibits two regions: an initial region where the increase in volume strain was due to the Poisson's effect, and a second region where a slower rate of increase in volume strain was due to shear deformation. Tensile volumetric deformation of an elastomer-modified epoxy exhibits the same type of behavior to that of the neat resin at low rates ( 3.2x0.01 sec(-1)). But at very high strain rates, which correspond more closely to the strain rates at the crack tip, there exists an increase in volume strain beyond the Poisson's effect. TEM, SEM and OM studies indicate that the rubber particles had voided. When a thin section from the deformed region is viewed under crossed-polarized light, shear bands are seen connecting voided rubber particles. From this information cavitation and enhanced shear band formation is proposed as the toughening mechanism.

  9. Electrodeposition properties of modified cational epoxy resin-type photoresist

    International Nuclear Information System (INIS)

    Yong He; Yunlong Zhang; Feipeng Wu; Miaozhen Li; Erjian Wang

    1999-01-01

    Multi-component cationic epoxy and acrylic resin system for ED photoresist was used in this work, since they can provide better storage stability for ED emulsion and better physical and chemical properties of deposited film than one-component system. The cationic main resin (AE) was prepared from amine modified epoxy resins and then treated with acetic acid. The amination degree was controlled as required. The synthetic procedure of cationic main resins is described in scheme I. The ED photoresist (AME) is composed of cationic main resin (AE) and nonionic multifunctional acrylic crosslinkers (PETA), in combination with suitable photo-initiator. They can easily be dispersed in deionized water to form a stable ED emulsion. The exposed part of deposited film upon UV irradiation occurs crosslinking to produce an insoluble semi-penetrating network and the unexposed part remains good solubility in the acidic water solution. It is readily utilized for fabrication of fine micropattern. The electrodeposition are carried out on Cu plate at room temperature. To evaluate the electrodeposition properties of ED photoresist (AME), the different influences are examined

  10. Sensibilización a bisfenol A y bisfenol F en trabajadores expuestos a resinas epoxi

    Directory of Open Access Journals (Sweden)

    L. Jiménez Bajo

    2008-06-01

    Full Text Available Las aplicaciones de las diferentes resinas epoxi basadas en bisfenol A y F son extensas. Las resinas epoxi basadas en bisfenol F son más nuevas y resistentes que las de bisfenol A, y ambas son causa conocida de dermatitis de contacto alérgica. Se estudian 39 casos de sensibilización a resinas epoxi en los últimos 5 años. Los resultados obtenidos son: prevalencia de sensibilización a resinas epoxi entre los pacientes estudiados del 2%, 27 varones y 8 mujeres, con una edad media de 42.77, un período de medio sensibilización de 23,8 meses. La sensibilización a bisfenol F desde que se incluye para las pruebas del parche en la batería de resinas epoxi es del 100% para los casos sensibilizados a la resina. La localización mayoritaria se dio en las manos, con una relevancia actual del 84%. Se recomendó un cambio de puesto en el trabajo al 46% de estos pacientes. El aumento de la sensibilización encontrada a bisfenol F puede explicarse por una sensibilización concomitante con bisfenol A, una declaración incorrecta de la composición de la resina o una reactividad cruzada de ambos.The applications of epoxy resins based on bisphenol A and F are extensive. Epoxy resins based on bisphenol F are new and more resistant than epoxy resins based on bisphenol A. Both of them cause allergic contact dermatitis. In the last 5 years, we have studied 39 cases of sensitization to epoxy resin. The results of our study were these: the global prevalence of epoxy resin sensitization was 2%, 27 men and 8 women. The mean age was 42.77 years and the sensitization period was 23.8 months. The most frequent localization of the lesions were hands (84% of the patients. Since bisphenol F was included in epoxy resin battery for patch testing, a 100% of positives responses in patients sensitized to epoxy resin have been found. Sensitization to epoxy resins was a cause of change in workplace in 46% of cases in our series. There has been an increase in sensitization of

  11. Molecular Modeling of Aerospace Polymer Matrices Including Carbon Nanotube-Enhanced Epoxy

    Science.gov (United States)

    Radue, Matthew S.

    Carbon fiber (CF) composites are increasingly replacing metals used in major structural parts of aircraft, spacecraft, and automobiles. The current limitations of carbon fiber composites are addressed through computational material design by modeling the salient aerospace matrix materials. Molecular Dynamics (MD) models of epoxies with and without carbon nanotube (CNT) reinforcement and models of pure bismaleimides (BMIs) were developed to elucidate structure-property relationships for improved selection and tailoring of matrices. The influence of monomer functionality on the mechanical properties of epoxies is studied using the Reax Force Field (ReaxFF). From deformation simulations, the Young's modulus, yield point, and Poisson's ratio are calculated and analyzed. The results demonstrate an increase in stiffness and yield strength with increasing resin functionality. Comparison between the network structures of distinct epoxies is further advanced by the Monomeric Degree Index (MDI). Experimental validation demonstrates the MD results correctly predict the relationship in Young's moduli for all epoxies modeled. Therefore, the ReaxFF is confirmed to be a useful tool for studying the mechanical behavior of epoxies. While epoxies have been well-studied using MD, there has been no concerted effort to model cured BMI polymers due to the complexity of the network-forming reactions. A novel, adaptable crosslinking framework is developed for implementing 5 distinct cure reactions of Matrimid-5292 (a BMI resin) and investigating the network structure using MD simulations. The influence of different cure reactions and extent of curing are analyzed on the several thermo-mechanical properties such as mass density, glass transition temperature, coefficient of thermal expansion, elastic moduli, and thermal conductivity. The developed crosslinked models correctly predict experimentally observed trends for various properties. Finally, the epoxies modeled (di-, tri-, and tetra

  12. Surface-bounded growth modeling applied to human mandibles

    DEFF Research Database (Denmark)

    Andresen, Per Rønsholt; Brookstein, F. L.; Conradsen, Knut

    2000-01-01

    automatically using shape features and a new algorithm called geometry-constrained diffusion. The semilandmarks are mapped into Procrustes space. Principal component analysis extracts a one-dimensional subspace, which is used to construct a linear growth model. The worst case mean modeling error in a cross...

  13. Inhibition of surface bound carbonate stabilization of tetragonal zirconia

    DEFF Research Database (Denmark)

    Nielsen, Mette Skovgaard; Almdal, Kristoffer; Lelieveld, A. van

    2011-01-01

    Water is known to initiate a tetragonal to monoclinic phase transformation in zirconia particles. Carbonates on the zirconia surface react with water molecules and hence reduce the transformation rate. This study investigates the possibility of inhibition of the reaction between surface carbonates...... and water in order to increase the transformation rate in the zirconia crystals. It was found possible to limit the reaction by reacting the surface carbonates with alcohols, a thiol and a primary amide prior to reaction with water. It was also concluded that di- and trialcohols are able to stabilize...

  14. Surface-bound microgels - From physicochemical properties to biomedical applications

    DEFF Research Database (Denmark)

    Nyström, Lina; Malmsten, Martin

    2016-01-01

    Microgels offer robust and facile approaches for surface modification, as well as opportunities to introduce biological functionality by loading such structures with bioactive agents, e.g., in the context of drug delivery, functional biomaterials, and biosensors. As such, they provide a versatile...

  15. Epoxy/anhydride thermosets modified with end-capped star polymers with poly(ethyleneimine cores of different molecular weight and poly(ε–caprolactone arms

    Directory of Open Access Journals (Sweden)

    C. Acebo

    2015-09-01

    Full Text Available Multiarm star polymers, with a hyperbranched poly(ethyleneimine (PEI core and poly(ε-caprolactone (PCL arms end-capped with acetyl groups were synthesized by ring-opening polymerization of ε-caprolactone from PEI cores of different molecular weight. These star polymers were used as toughening agents for epoxy/anhydride thermosets. The curing process was studied by calorimetry, thermomechanical analysis and infrared spectroscopy. The final properties of the resulting materials were determined by thermal and mechanical tests. The addition of the star polymers led to an improvement up to 130% on impact strength and a reduction in the thermal stresses up to 55%. The structure and molecular weight of the modifier used affected the morphology of the resulting materials. Electron microscopy showed phase-separated morphologies with nano-sized fine particles well adhered to the epoxy/anhydride matrix when the higher molecular weight modifier was used.

  16. Heat-induced antigen retrieval of epoxy sections for electron microscopy.

    Science.gov (United States)

    Brorson, S H

    2001-07-01

    The purpose of this manuscript is to review the literature on the use of heat-induced antigen retrieval methods to enhance the immunolabeling of epoxy sections at the electron microscopical level. The history of the development of antigen retrieval by heating formaldehyde fixed paraffin sections in a buffer solution is given in short, and how this technique has been extended to resin sections and in particular epoxy sections is explained. Theories for the mechanism of enhancement of the immunolabeling of epoxy sections by the heat-retrieval method are discussed, and it is finally speculated whether most of the mechanisms for antigen retrieval on epoxy sections in heated buffer solution are essentially the same as for conventional immunoenhancing by deplastizing and etching. The more accelerator used in the processing of the tissue the more intense the immunolabeling of the heated epoxy sections becomes. The intensity of immunolabeling of the epoxy sections increases with the temperature in the heated buffer solution, and the intensity is significantly higher at high autoclave temperatures than at 95 degrees C, Heat-induced antigen retrieval is also compared with other, conventional techniques for enhancing the immunolabeling of epoxy sections.

  17. Non-occupational contact sensitization to epoxy resin of bisphenol A among general dermatology patients.

    Science.gov (United States)

    Majasuo, Susanna; Liippo, Jussi; Lammintausta, Kaija

    2012-03-01

    Sensitization to epoxy resins often results from occupational exposure in various fields of construction and industry. Non-occupational sensitization sources and environments have remained overlooked. To analyse non-occupational and occupational contact sensitization to epoxy resin of bisphenol A among general dermatology patients. Special attention was paid to patients sensitized from non-occupational sources. During a 10-year period, 6042 general dermatology patients were patch tested with epoxy resin (bisphenol A) in the Dermatology Clinic of Turku University Hospital. The clinical data and the sources of occupational and non-occupational exposure to epoxy resin were analysed in sensitized patients. Epoxy resin sensitization was found in 59 patients. Non-occupational sensitization was found in 21 (35%) patients, whereas the number of occupational cases was 38 (65%). The most common sources of non-occupational epoxy resin sensitization were materials used in domestic renovation and construction projects and in boat repair. Non-occupational sensitization sources account for approximately one-third of epoxy resin sensitization cases, and therefore represent an important risk among hobbies and leisure activities. © 2011 John Wiley & Sons A/S.

  18. MWCNT/TiO2hybrid nano filler toward high-performance epoxy composite.

    Science.gov (United States)

    Kumar, Arun; Kumar, Kaushal; Ghosh, P K; Yadav, K L

    2018-03-01

    In this work, multi-walled carbon nanotubes (MWCNTs) are decorated by TiO 2 nanoparticles and formed a new hybrid structure of filler (MWCNT/TiO 2 hybrid filler). The MWCNT/TiO 2 hybrid filler is reinforced in epoxy matrix and studied the mechanical and anti-corrosion properties of epoxy. The morphology of newly formed MWCNT/TiO 2 hybrid nano filler has been studied using transmission electron microscopy (TEM). Field Emission Scanning Electron Microscope (FESEM) images of tensile fracture surface confirmed the superior dispersion of MWCNT/TiO 2 in the epoxy matrix. The resultant MWCNT/TiO 2 hybrid-epoxy nanocomposite exhibits superior anti-corrosion and mechanical performance than the nanocomposite produced by loading of only MWCNTs or TiO 2 nanoparticles as well as neat epoxy. For example, tensile strength and storage modulus of epoxy increased by 61% and 43% respectively on loading of MWCNT/TiO 2 hybrid nano filler. Furthermore, the coating of MWCNT/TiO 2 hybrid-epoxy nanocomposite on mild steel reduces the corrosion rate upto 0.87×10 -3 MPY from 16.81MPY. Copyright © 2017 Elsevier B.V. All rights reserved.

  19. Effect of electron beam irradiation on thermal and mechanical properties of aluminum based epoxy composites

    Science.gov (United States)

    Visakh, P. M.; Nazarenko, O. B.; Sarath Chandran, C.; Melnikova, T. V.; Nazarenko, S. Yu.; Kim, J.-C.

    2017-07-01

    The epoxy resins are widely used in nuclear and aerospace industries. The certain properties of epoxy resins as well as the resistance to radiation can be improved by the incorporation of different fillers. This study examines the effect of electron beam irradiation on the thermal and mechanical properties of the epoxy composites filled with aluminum nanoparticles at percentage of 0.35 wt%. The epoxy composites were exposed to the irradiation doses of 30, 100 and 300 kGy using electron beam generated by the linear electron accelerator ELU-4. The effects of the doses on thermal and mechanical properties of the aluminum based epoxy composites were investigated by the methods of thermal gravimetric analysis, tensile test, and dynamic mechanical analysis. The results revealed that the studied epoxy composites showed good radiation resistance. The thermal and mechanical properties of the aluminum based epoxy composites increased with increasing the irradiation dose up to 100 kGy and decreased with further increasing the dose.

  20. Enhanced thermal conductivity of epoxy composites filled with silicon carbide nanowires.

    Science.gov (United States)

    Shen, Dianyu; Zhan, Zhaolin; Liu, Zhiduo; Cao, Yong; Zhou, Li; Liu, Yuanli; Dai, Wen; Nishimura, Kazuhito; Li, Chaoyang; Lin, Cheng-Te; Jiang, Nan; Yu, Jinhong

    2017-06-01

    In this study, we report a facile approach to fabricate epoxy composite incorporated with silicon carbide nanowires (SiC NWs). The thermal conductivity of epoxy/SiC NWs composites was thoroughly investigated. The thermal conductivity of epoxy/SiC NWs composites with 3.0 wt% filler reached 0.449 Wm -1  K -1 , approximately a 106% enhancement as compared to neat epoxy. In contrast, the same mass fraction of silicon carbide micron particles (SiC MPs) incorporated into epoxy matrix showed less improvement on thermal conduction properties. This is attributed to the formation of effective heat conduction pathways among SiC NWs as well as a strong interaction between the nanowires and epoxy matrix. In addition, the thermal properties of epoxy/SiC NWs composites were also improved. These results demonstrate that we developed a novel approach to enhance the thermal conductivity of the polymer composites which meet the requirement for the rapid development of the electronic devices.