WorldWideScience

Sample records for surface showed high

  1. A high surface area Zr(IV)-based metal-organic framework showing stepwise gas adsorption and selective dye uptake

    Science.gov (United States)

    Lv, Xiu-Liang; Tong, Minman; Huang, Hongliang; Wang, Bin; Gan, Lei; Yang, Qingyuan; Zhong, Chongli; Li, Jian-Rong

    2015-03-01

    Exploitation of new metal-organic framework (MOF) materials with high surface areas has been attracting great attention in related research communities due to their broad potential applications. In this work, a new Zr(IV)-based MOF, [Zr6O4(OH)4(eddb)6] (BUT-30, H2eddb=4,4‧-(ethyne-1,2-diyl)dibenzoic acid) has been solvothermally synthesized, characterized, and explored for gases and dyes adsorptions. Single-crystal X-ray diffraction analysis demonstrates a three-dimensional cubic framework structure of this MOF, in which each Zr6O4(OH)4 building unit is linked by 12 linear eddb ligands. BUT-30 has been found stable up to 400 °C and has a Brunauer-Emmett-Teller (BET) surface area as high as 3940.6 m2 g-1 (based on the N2 adsorption at 77 K) and total pore volume of 1.55 cm3 g-1. It is more interesting that this MOF exhibits stepwise adsorption behaviors for Ar, N2, and CO2 at low temperatures, and selective uptakes towards different ionic dyes.

  2. Pentamycin shows high efficacy against Trichomonas vaginalis.

    Science.gov (United States)

    Kranzler, Markus; Syrowatka, Michael; Leitsch, David; Winnips, Cornelis; Walochnik, Julia

    2015-04-01

    Trichomonas vaginalis is the causative agent of the venereal disease trichomoniasis, which is the most frequent non-viral sexually transmitted disease worldwide. Since the 1960s, metronidazole has been the standard treatment, however an increasing number of cases with metronidazole-resistant strains is being reported. In this study, pentamycin, a polyene antibiotic, was tested for its in vitro efficacy against T. vaginalis using four strains with different metronidazole susceptibilities. It was shown that pentamycin is highly active against T. vaginalis and that the effect is prompt and independent of underlying metronidazole resistance. The effective concentrations (EC values) after 1 h of treatment were in the range 1.74-2.62 μg/mL (EC50) and 4.91-6.51 μg/mL (EC90). Total eradication of trichomonads (EC100) was achieved in all strains by treatment with 15 μg/mL (22 μM) for 1 h or with ≥1 μg/mL (≥1.5 μM) for 24 h. Long-term cultivation (12 months) under permanent drug pressure did not induce stable resistance against pentamycin in any of the strains tested. Pentamycin has been approved for intravaginal use and is a promising candidate for the topical treatment of trichomoniasis.

  3. Enterococcus faecalis strains show culture heterogeneity in cell surface charge

    NARCIS (Netherlands)

    van Merode, Annet; van der Mei, HC; Busscher, HJ; Waar, K; Krom, BP

    2006-01-01

    Adhesion of micro-organisms to biotic and abiotic surfaces is an important virulence factor and involves different types of interactions. Enterococcus faecalis, a human commensal and an important opportunistic pathogen, has the ability to adhere to surfaces. Biliary stents frequently become clogged

  4. Surface texture metrology for high precision surfaces

    DEFF Research Database (Denmark)

    Hansen, Hans Nørgaard; Gasparin, Stefania; Tosello, Guido

    2010-01-01

    This paper introduces some of the challenges related to surface texture measurement of high precision surfaces. The paper is presenting two case studies related to polished tool surfaces and micro part surfaces. In both cases measuring instrumentation, measurement procedure and the measurement...

  5. Surface texture metrology for high precision surfaces

    DEFF Research Database (Denmark)

    Hansen, Hans Nørgaard; Gasparin, Stefania; Tosello, Guido

    2010-01-01

    This paper introduces some of the challenges related to surface texture measurement of high precision surfaces. The paper is presenting two case studies related to polished tool surfaces and micro part surfaces. In both cases measuring instrumentation, measurement procedure and the measurement re...

  6. Highly reflective reasoners show no signs of belief inhibition.

    Science.gov (United States)

    Svedholm-Häkkinen, Annika M

    2015-01-01

    The processes underlying individual differences in reasoning performance are not entirely understood. What do people who do well on reasoning tasks where beliefs and logic conflict do differently from other people? Because abundant evidence shows that even poorer reasoners detect these conflicts, it has been suggested that individual differences in reasoning performance arise from inhibition failures later in the reasoning process. The present paper argues that a minority of highly skilled reasoners may deviate from this general reasoning process from an early stage. Two studies investigated signs of belief inhibition using a lexical access paradigm (Study 1) and a negative priming paradigm (Study 2). Study 1 showed that while other people exhibited signs of belief inhibition following a belief-logic conflict, people with the highest disposition for cognitive reflection did not. In Study 2, this finding was replicated and similar results were also obtained when comparing groups with higher and lower general cognitive ability. Two possible explanations are discussed. The reasoners with a highly reflective cognitive style or high general cognitive ability may have engaged and inhibited belief processing but if so, they may have been exceptionally efficient at recovering from it, wherefore no belief inhibition effects were found. An alternative account is that these reasoners started Type 2 processing directly, without first engaging in and then inhibiting belief-based processing. Under either explanation, the results indicate that individual differences in reasoning may partly arise from differences that occur early in the reasoning process.

  7. Mixtures of thermostable enzymes show high performance in biomass saccharification.

    Science.gov (United States)

    Kallioinen, Anne; Puranen, Terhi; Siika-aho, Matti

    2014-07-01

    Optimal enzyme mixtures of six Trichoderma reesei enzymes and five thermostable enzyme components were developed for the hydrolysis of hydrothermally pretreated wheat straw, alkaline oxidised sugar cane bagasse and steam-exploded bagasse by statistically designed experiments. Preliminary studies to narrow down the optimization parameters showed that a cellobiohydrolase/endoglucanase (CBH/EG) ratio of 4:1 or higher of thermostable enzymes gave the maximal CBH-EG synergy in the hydrolysis of hydrothermally pretreated wheat straw. The composition of optimal enzyme mixtures depended clearly on the substrate and on the enzyme system studied. The optimal enzyme mixture of thermostable enzymes was dominated by Cel7A and required a relatively high amount of xylanase, whereas with T. reesei enzymes, the high proportion of Cel7B appeared to provide the required xylanase activity. The main effect of the pretreatment method was that the required proportion of xylanase was higher and the proportion of Cel7A lower in the optimized mixture for hydrolysis of alkaline oxidised bagasse than steam-exploded bagasse. In prolonged hydrolyses, less Cel7A was generally required in the optimal mixture. Five-component mixtures of thermostable enzymes showed comparable hydrolysis yields to those of commercial enzyme mixtures.

  8. The neonicotinoid imidachloprid shows high chronic toxicity to mayfly nymphs

    NARCIS (Netherlands)

    Roessink, I.; Merga, L.B.; Zweers, A.J.; Brink, van den P.J.

    2013-01-01

    The present study evaluated the acute and chronic toxicity of imidacloprid to a range of freshwater arthropods. Mayfly and caddisfly species were most sensitive to short-term imidacloprid exposures (10 tests), whereas the mayflies showed by far the most sensitive response to long-term exposure of al

  9. Italian high technology shows its wares at CERN

    CERN Multimedia

    Maximilien Brice

    2005-01-01

    Italian industry held an exhibition at CERN on 14-17 November with 26 firms displaying innovative technological developments. In particular it featured categories such as mechanics, high-vacuum technologies, electronics for detectors, and electric and civil engineering. The exhibition was inaugurated in the presence of Guido Possa, vice-minister for education, universities and research. The event was organized by Sandro Centro, INFN researcher and Industrial Liaison Officer at CERN, along with Federico Ferrini, scientific officer for International Organizations of Geneva and the Italian Chamber of Commerce in Switzerland

  10. Physically and chemically stable ionic liquid-infused textured surfaces showing excellent dynamic omniphobicity

    Directory of Open Access Journals (Sweden)

    Daniel F. Miranda

    2014-05-01

    Full Text Available A fluorinated and hydrophobic ionic liquid (IL, 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl imide, effectively served as an advantageous lubricating liquid for the preparation of physically and chemically stable omniphobic surfaces based on slippery liquid-infused porous surfaces. Here, we used particulate microstructures as supports, prepared by the chemical vapor deposition of 1,3,5,7-tetramethylcyclotetrasiloxane and subsequent surface modification with (3-aminopropyltriethoxysilane. Confirmed by SEM and contact angle measurements, the resulting IL-infused microtextured surfaces are smooth and not only water but also various low surface tension liquids can easily slide off at low substrate tilt angles of <5°, even after exposure to high temperature, vacuum, and UV irradiation.

  11. Physically and chemically stable ionic liquid-infused textured surfaces showing excellent dynamic omniphobicity

    Energy Technology Data Exchange (ETDEWEB)

    Miranda, Daniel F.; Urata, Chihiro; Masheder, Benjamin; Dunderdale, Gary J.; Hozumi, Atsushi, E-mail: a.hozumi@aist.go.jp [National Institute of Advanced Industrial Science and Technology (AIST), 2266-98, Anagahora, Shimo-Shidami, Moriyama-ku, Nagoya, Aichi 463-8560 (Japan); Yagihashi, Makoto [Nagoya Municipal Industrial Research Institute, Rokuban, Atsuta-ku, Nagoya 456-0058 (Japan)

    2014-05-01

    A fluorinated and hydrophobic ionic liquid (IL), 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl) imide, effectively served as an advantageous lubricating liquid for the preparation of physically and chemically stable omniphobic surfaces based on slippery liquid-infused porous surfaces. Here, we used particulate microstructures as supports, prepared by the chemical vapor deposition of 1,3,5,7-tetramethylcyclotetrasiloxane and subsequent surface modification with (3-aminopropyl)triethoxysilane. Confirmed by SEM and contact angle measurements, the resulting IL-infused microtextured surfaces are smooth and not only water but also various low surface tension liquids can easily slide off at low substrate tilt angles of <5°, even after exposure to high temperature, vacuum, and UV irradiation.

  12. Hydrophobic/superhydrophobic oxidized metal surfaces showing negligible contact angle hysteresis.

    Science.gov (United States)

    Hozumi, Atsushi; Cheng, Dalton F; Yagihashi, Makoto

    2011-01-15

    Dynamic wettability of oxidized metal (aluminum and titanium) surfaces could be tuned by chemical vapor deposition (CVD) of 1,3,5,7-tetramethylcyclotetrasiloxane (D(4)(H)). This facile CVD method produces not only monomeric layers but also particulate films by changing the CVD temperature, resulting in a marked difference in the final wetting properties. In the samples prepared at 80°C for ~3 days, D(4)(H) layers with thicknesses of ~0.5 nm were formed on the surfaces without discernible change in surface morphology, as evidenced by X-ray photoelectron spectroscopy and atomic force microscopy. After this D(4)(H) monomeric layer formation, the hydrophilic oxidized aluminum and titanium surfaces became hydrophobic (advancing/receding water contact angles (θ(A)/θ(R))=102-104°/99-102°) showing essentially negligible contact angle hysteresis. Performing CVD of D(4)(H) at 180°C for ~1 day produced opaque film with particulate morphologies with diameters in the range of 500 nm to 4 μm observed on the surfaces. This geometric morphology enhanced the surface hydrophobicity (θ(A)/θ(R)=163°/160-161°). Droplets on these negligible-hysteresis surfaces moved very easily without "pinning".

  13. On the existence of high index topologically minimal surfaces

    CERN Document Server

    Bachman, David

    2009-01-01

    The topological index of a surface was previously introduced by the first author as the topological analogue of the index of an unstable minimal surface. Here we show that surfaces of arbitrarily high topological index exist.

  14. Leishmania-specific surface antigens show sub-genus sequence variation and immune recognition.

    Directory of Open Access Journals (Sweden)

    Daniel P Depledge

    Full Text Available BACKGROUND: A family of hydrophilic acylated surface (HASP proteins, containing extensive and variant amino acid repeats, is expressed at the plasma membrane in infective extracellular (metacyclic and intracellular (amastigote stages of Old World Leishmania species. While HASPs are antigenic in the host and can induce protective immune responses, the biological functions of these Leishmania-specific proteins remain unresolved. Previous genome analysis has suggested that parasites of the sub-genus Leishmania (Viannia have lost HASP genes from their genomes. METHODS/PRINCIPAL FINDINGS: We have used molecular and cellular methods to analyse HASP expression in New World Leishmania mexicana complex species and show that, unlike in L. major, these proteins are expressed predominantly following differentiation into amastigotes within macrophages. Further genome analysis has revealed that the L. (Viannia species, L. (V. braziliensis, does express HASP-like proteins of low amino acid similarity but with similar biochemical characteristics, from genes present on a region of chromosome 23 that is syntenic with the HASP/SHERP locus in Old World Leishmania species and the L. (L. mexicana complex. A related gene is also present in Leptomonas seymouri and this may represent the ancestral copy of these Leishmania-genus specific sequences. The L. braziliensis HASP-like proteins (named the orthologous (o HASPs are predominantly expressed on the plasma membrane in amastigotes and are recognised by immune sera taken from 4 out of 6 leishmaniasis patients tested in an endemic region of Brazil. Analysis of the repetitive domains of the oHASPs has shown considerable genetic variation in parasite isolates taken from the same patients, suggesting that antigenic change may play a role in immune recognition of this protein family. CONCLUSIONS/SIGNIFICANCE: These findings confirm that antigenic hydrophilic acylated proteins are expressed from genes in the same chromosomal

  15. High surface area, high permeability carbon monoliths

    Energy Technology Data Exchange (ETDEWEB)

    Lagasse, R.R.; Schroeder, J.L. [Sandia National Labs., Albuquerque, NM (United States). Organic Materials Processing Dept.

    1994-12-31

    The goal of this work is to prepare carbon monoliths having precisely tailored pore size distribution. Prior studies have demonstrated that poly(acrylonitrile) can be processed into a precursor having tailored macropore structure. Since the macropores were preserved during pyrolysis, this synthetic process provided a route to porous carbon having macropores with size =0.1 to 10{mu}m. No micropores of size <2 nm could be detected in the carbon, however, by nitrogen adsorption. In the present work, the authors have processed a different polymer, poly(vinylidene chloride) into a macroporous precursor, Pyrolysis produced carbon monoliths having macropores derived from the polymer precursor as well as extensive microporosity produced during the pyrolysis of the polymer. One of these carbons had BET surface area of 1,050 m{sup 2}/g and about 1.2 cc/g total pore volume, with about 1/3 of the total pore volume in micropores and the remainder in 1{mu}m macropores. No mesopores in the intermediate size range could be detected by nitrogen adsorption. Carbon materials having high surface area as well as micron size pores have potential applications as electrodes for double layer supercapacitors containing liquid electrolyte, or as efficient media for performing chemical separations.

  16. Lithium inclusion in indium metal-organic frameworks showing increased surface area and hydrogen adsorption

    Directory of Open Access Journals (Sweden)

    Mathieu Bosch

    2014-12-01

    Full Text Available Investigation of counterion exchange in two anionic In-Metal-Organic Frameworks (In-MOFs showed that partial replacement of disordered ammonium cations was achieved through the pre-synthetic addition of LiOH to the reaction mixture. This resulted in a surface area increase of over 1600% in {Li [In(1,3 − BDC2]}n and enhancement of the H2 uptake of approximately 275% at 80 000 Pa at 77 K. This method resulted in frameworks with permanent lithium content after repeated solvent exchange as confirmed by inductively coupled plasma mass spectrometry. Lithium counterion replacement appears to increase porosity after activation through replacement of bulkier, softer counterions and demonstrates tuning of pore size and properties in MOFs.

  17. High-Luminance Road Surfaces,

    Science.gov (United States)

    1980-12-01

    condition was changed with the decreased use of snow chains and increasing use of studded tires. The studded tires wear down the road surface in a...region, white anorthosite of a uniform and unweathered type is usable as an additive to asphalt con- crete and wear surfacing for asphalt gravel...CLASSIFICATION Of THIS PAGE(W/em Daateoo 20. Abstract (cont’d) resistance to weathering, and the degree of luminosity. Quartzites have the best wear

  18. Direct Covalent Grafting of Phytate to Titanium Surfaces through Ti-O-P Bonding Shows Bone Stimulating Surface Properties and Decreased Bacterial Adhesion.

    Science.gov (United States)

    Córdoba, Alba; Hierro-Oliva, Margarita; Pacha-Olivenza, Miguel Ángel; Fernández-Calderón, María Coronada; Perelló, Joan; Isern, Bernat; González-Martín, María Luisa; Monjo, Marta; Ramis, Joana M

    2016-05-11

    Myo-inositol hexaphosphate, also called phytic acid or phytate (IP6), is a natural molecule abundant in vegetable seeds and legumes. Among other functions, IP6 inhibits bone resorption. It is adsorbed on the surface of hydroxyapatite, inhibiting its dissolution and decreasing the progressive loss of bone mass. We present here a method to directly functionalize Ti surfaces covalently with IP6, without using a cross-linker molecule, through the reaction of the phosphate groups of IP6 with the TiO2 layer of Ti substrates. The grafting reaction consisted of an immersion in an IP6 solution to allow the physisorption of the molecules onto the substrate, followed by a heating step to obtain its chemisorption, in an adaptation of the T-Bag method. The reaction was highly dependent on the IP6 solution pH, only achieving a covalent Ti-O-P bond at pH 0. We evaluated two acidic pretreatments of the Ti surface, to increase its hydroxylic content, HNO3 30% and HF 0.2%. The structure of the coated surfaces was characterized by X-ray photoelectron spectroscopy, time-of-flight secondary ion mass spectrometry, and ellipsometry. The stability of the IP6 coating after three months of storage and after sterilization with γ-irradiation was also determined. Then, we evaluated the biological effect of Ti-IP6 surfaces in vitro on MC3T3-E1 osteoblastic cells, showing an osteogenic effect. Finally, the effect of the surfaces on the adhesion and biofilm viability of oral microorganisms S. mutans and S. sanguinis was also studied, and we found that Ti-IP6 surfaces decreased the adhesion of S. sanguinis. A surface that actively improves osseointegration while decreasing the bacterial adhesion could be suitable for use in bone implants.

  19. Invisible high workfunction materials on heterogeneous surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Sharma, Anirudh [Flinders Centre for Nanoscale Science and Technology, Flinders University, P.O. Box 2100, Adelaide, SA 5001 (Australia); Max Planck Institute for Polymer Research, Ackermannweg 10, Mainz 55128 (Germany); Berger, Rüdiger [Max Planck Institute for Polymer Research, Ackermannweg 10, Mainz 55128 (Germany); Lewis, David A. [Flinders Centre for Nanoscale Science and Technology, Flinders University, P.O. Box 2100, Adelaide, SA 5001 (Australia); Andersson, Gunther G., E-mail: gunther.andersson@flinders.edu.au [Flinders Centre for Nanoscale Science and Technology, Flinders University, P.O. Box 2100, Adelaide, SA 5001 (Australia)

    2015-02-01

    Graphical abstract: - Highlights: • Heterogeneous surfaces show a distribution in their surface properties. • The higher workfunction components contribute less to the secondary electron cut-off. • The higher workfunction components are overlooked in the workfunction analysis. • The analysis of electronic device performance is affected. - Abstract: We demonstrate that the determination of workfunction of heterogeneous surfaces by electron spectroscopy measurements is complex due to enhanced secondary electron emission from the lower workfunction material. This can lead to misunderstanding the electronic properties of interfaces in electronic devices and have significant influence on the design and performance of the interfaces therein. Ultraviolet photoelectron spectroscopy (UPS) measurement on a range of artificially created ITO-Au heterogeneous surfaces demonstrates that contributions to the secondary electron cut-off are not proportional to the compound coverage on the surface and that the lower workfunction material dominates the secondary electron cut-off. As a consequence the contribution of the high workfunction material to the overall workfunction distribution can be overlooked.

  20. The atherogenic Scarb1 null mouse model shows a high bone mass phenotype.

    Science.gov (United States)

    Martineau, Corine; Martin-Falstrault, Louise; Brissette, Louise; Moreau, Robert

    2014-01-01

    Scavenger receptor class B, type I (SR-BI), the Scarb1 gene product, is a receptor associated with cholesteryl ester uptake from high-density lipoproteins (HDL), which drives cholesterol movement from peripheral tissues toward the liver for excretion, and, consequently, Scarb1 null mice are prone to atherosclerosis. Because studies have linked atherosclerosis incidence with osteoporosis, we characterized the bone metabolism in these mice. Bone morphometry was assessed through microcomputed tomography and histology. Marrow stromal cells (MSCs) were used to characterize influence of endogenous SR-BI in cell functions. Total and HDL-associated cholesterol in null mice were increased by 32-60%, correlating with its role in lipoprotein metabolism. Distal metaphyses from 2- and 4-mo-old null mice showed correspondingly 46 and 37% higher bone volume fraction associated with a higher number of trabeculae. Histomorphometric analyses in 2-mo-old null male mice revealed 1.42-fold greater osteoblast surface, 1.37-fold higher percent mineralizing surface, and 1.69-fold enhanced bone formation rate. In vitro assays for MSCs from null mice revealed 37% higher proliferation rate, 48% more alkaline phosphatase activity, 70% greater mineralization potential and a 2-fold osterix (Sp7) expression, yet a 0.5-fold decrease in caveolin-1 (Cav1) expression. Selective uptake levels of HDL-associated cholesteryl oleate and estradiol were similar between MSC from wild-type and Scarb1 null mice, suggesting that its contribution to this process is not its main role in these cells. However, Scarb1 knockout stunted the HDL-dependent regulation of Cav1 genic expression. Scarb1 null mice are not prone to osteoporosis but show higher bone mass associated with enhanced bone formation.

  1. A Simple Experiment to Show Photodynamic Inactivation of Bacteria on Surfaces

    Science.gov (United States)

    Caminos, Daniel A.; Durantini, Edgardo N.

    2007-01-01

    New suitable approaches were investigated to visualize the photodynamic inactivation (PDI) of bacteria immobilized on agar surfaces. The PDI capacities of a cationic photosensitizer (5,10,15,20-tetra(4-N,N,N-trimethylammoniumphenyl)porphyrin) and an anionic photosensitizer (5,10,15,20-tetra(4-sulfonatophenyl)porphyrin) were analyzed on a typical…

  2. High-speed atomic force microscopy shows that annexin V stabilizes membranes on the second timescale

    Science.gov (United States)

    Miyagi, Atsushi; Chipot, Christophe; Rangl, Martina; Scheuring, Simon

    2016-09-01

    Annexins are abundant cytoplasmic proteins that can bind to negatively charged phospholipids in a Ca2+-dependent manner, and are known to play a role in the storage of Ca2+ and membrane healing. Little is known, however, about the dynamic processes of protein-Ca2+-membrane assembly and disassembly. Here we show that high-speed atomic force microscopy (HS-AFM) can be used to repeatedly induce and disrupt annexin assemblies and study their structure, dynamics and interactions. Our HS-AFM set-up is adapted for such biological applications through the integration of a pumping system for buffer exchange and a pulsed laser system for uncaging caged compounds. We find that biochemically identical annexins (annexin V) display different effective Ca2+ and membrane affinities depending on the assembly location, providing a wide Ca2+ buffering regime while maintaining membrane stabilization. We also show that annexin is membrane-recruited and forms stable supramolecular assemblies within ˜5 s in conditions that are comparable to a membrane lesion in a cell. Molecular dynamics simulations provide atomic detail of the role played by Ca2+ in the reversible binding of annexin to the membrane surface.

  3. Surface nanostructures by single highly charged ions.

    Science.gov (United States)

    Facsko, S; Heller, R; El-Said, A S; Meissl, W; Aumayr, F

    2009-06-03

    It has recently been demonstrated that the impact of individual, slow but highly charged ions on various surfaces can induce surface modifications with nanometer dimensions. Generally, the size of these surface modifications (blisters, hillocks, craters or pits) increases dramatically with the potential energy of the highly charged ion, while the kinetic energy of the projectile ions seems to be of little importance. This paper presents the currently available experimental evidence and theoretical models and discusses the circumstances and conditions under which nanosized features on different surfaces due to the impact of slow highly charged ions can be produced.

  4. The Surface Chemical Properties of Novel High Surface Area Solids ...

    African Journals Online (AJOL)

    and MFA3 are the result of the high chromium content in the original ash (UFA1). ... ties has a significant influence on the crystal form produced during zeolite ... that the surface is enriched in Si compared with the bulk compo- sition. This is ...

  5. A simple identification method for spore-forming bacteria showing high resistance against [gamma]-rays

    Energy Technology Data Exchange (ETDEWEB)

    Koshikawa, Tomihiko; Sone, Koji; Kobayashi, Toshikazu (Japan Radioisotope Association, Koka, Shiga (Japan). Koka Lab.)

    1993-11-01

    A simple identification method was developed for spore-forming bacteria which are highly resistant against [gamma]-rays. Among 23 species of Bacillus studied, the spores of Bacillus megaterium, B. cereus, B. thuringiensis, B. pumilus and B. aneurinolyticus showed high resistance against [gamma]-rays as compared with other spores of Bacillus species. Combination of the seven kinds of biochemical tests, namely, the citrate utilization test, nitrate reduction test, starch hydrolysis test, Voges-Proskauer reaction test, gelatine hydrolysis test, mannitol utilization test and xylose utilization test showed a characteristic pattern for each species of Bacillus. The combination pattern of each the above tests with a few supplementary test, if necessary, was useful to identify Bacillus species showing high radiation resistance against [gamma]-rays. The method is specific for B. megaterium, B. thuringiensis and B. pumilus, and highly selective for B. aneurinolyticus and B. cereus. (author).

  6. Calcium phosphate coating containing silver shows high antibacterial activity and low cytotoxicity and inhibits bacterial adhesion

    Energy Technology Data Exchange (ETDEWEB)

    Ando, Yoshiki, E-mail: andoy@jmmc.jp [Division of Microbiology, Department of Pathology and Microbiology, Faculty of Medicine, Saga University, 5-1-1 Nabeshima, Saga 849-8501 (Japan); Research Department, Japan Medical Materials Corporation, Uemura Nissei Bldg.9F 3-3-31 Miyahara, Yodogawa-ku, Osaka 532-0003 (Japan); Miyamoto, Hiroshi [Division of Microbiology, Department of Pathology and Microbiology, Faculty of Medicine, Saga University, 5-1-1 Nabeshima, Saga 849-8501 (Japan); Noda, Iwao; Sakurai, Nobuko [Research Department, Japan Medical Materials Corporation, Uemura Nissei Bldg.9F 3-3-31 Miyahara, Yodogawa-ku, Osaka 532-0003 (Japan); Akiyama, Tomonori [Division of Microbiology, Department of Pathology and Microbiology, Faculty of Medicine, Saga University, 5-1-1 Nabeshima, Saga 849-8501 (Japan); Yonekura, Yutaka; Shimazaki, Takafumi; Miyazaki, Masaki; Mawatari, Masaaki; Hotokebuchi, Takao [Department of Orthopaedic Surgery, Faculty of Medicine, Saga University, 5-1-1 Nabeshima, Saga 849-8501 (Japan)

    2010-01-01

    Surgical site infection is one of the serious complications of orthopedic implants. In order to reduce the incidence of implant-associated infections, we developed a novel coating technology of calcium phosphate (CP) containing silver (Ag), designated Ag-CP coating, using a thermal spraying technique. In this study, we evaluated the antibacterial efficacy and biological safety of this coating. In vitro antibacterial activity tests showed that the growths of Escherichia coli, Staphylococcus aureus and methicillin-resistant S. aureus (MRSA) are completely suppressed on Ag-CP coating. In vitro bacterial adherence tests revealed that the number of adherent bacteria on the surface of this coating is significantly less (p < 0.02) than that on the surface of the CP coating. Moreover, the Ag-CP coating completely inhibits MRSA adhesion [<10 colony-forming units (CFU)] when 10{sup 2} CFU MRSA is inoculated. On the other hand, V79 Chinese hamster lung cells were found to grow on the Ag-CP coating as well as on the CP coating in a cytotoxicity test. These results indicate that the Ag-CP coating on the surface of orthopedic implants exhibits antibacterial activity and inhibits bacterial adhesion without cytotoxicity.

  7. Multilocus Phylogenetics Show High Levels of Endemic Fusaria Inhabiting Sardinian Soils (Tyrrhenian Islands)

    Science.gov (United States)

    The Mediterranean island of Sardinia is well known for high levels of vascular plant diversity and endemism, but little is known about its microbial diversity. Under the hypothesis that Fusarium species would show similar patterns, we estimated variability in Fusarium species composition among ten ...

  8. LHC collision event at CMS showing two high energy photons (CMS Higgs search)

    CERN Multimedia

    CMS Collaboration

    2011-01-01

    11sec animation of a Higgs->GammaGamma candidate in CMS. Real CMS proton-proton collision events in which two high energy photons (dashed orange lines and towers) are observed. The event shows characteristics expected from the decay of a Higgs boson but is also consistent with background Standard Model physics processes.

  9. LHC collision event at CMS showing four high energy electrons (CMS Higgs search)

    CERN Multimedia

    CMS Collaboration

    2011-01-01

    11sec animation of a Higgs->ZZ->4e candidate in CMS. Real CMS proton-proton collision events in which 4 high energy electrons (orange lines and towers) are observed. The event shows characteristics expected from the decay of a Higgs boson but is also consistent with background Standard Model physics processes.

  10. LHC collision event at CMS showing four high energy muons (CMS Higgs search)

    CERN Multimedia

    CMS Collaboration

    2011-01-01

    11sec animation of a Higgs->ZZ->4mu candidate being created CMS . Real CMS proton-proton collision events in which 4 high energy muons (light blue lines) are observed. The event shows characteristics expected from the decay of a Higgs boson but is also consistent with background Standard Model physics processes.

  11. Colloids with high-definition surface structures

    Science.gov (United States)

    Chen, Hsien-Yeh; Rouillard, Jean-Marie; Gulari, Erdogan; Lahann, Joerg

    2007-01-01

    Compared with the well equipped arsenal of surface modification methods for flat surfaces, techniques that are applicable to curved, colloidal surfaces are still in their infancy. This technological gap exists because spin-coating techniques used in traditional photolithographic processes are not applicable to the curved surfaces of spherical objects. By replacing spin-coated photoresist with a vapor-deposited, photodefinable polymer coating, we have now fabricated microstructured colloids with a wide range of surface patterns, including asymmetric and chiral surface structures, that so far were typically reserved for flat substrates. This high-throughput method can yield surface-structured colloidal particles at a rate of ≈107 to 108 particles per operator per day. Equipped with spatially defined binding pockets, microstructured colloids can engage in programmable interactions, which can lead to directed self-assembly. The ability to create a wide range of colloids with both simple and complex surface patterns may contribute to the genesis of previously unknown colloidal structures and may have important technological implications in a range of different applications, including photonic and phononic materials or chemical sensors. PMID:17592149

  12. Colloids with high-definition surface structures.

    Science.gov (United States)

    Chen, Hsien-Yeh; Rouillard, Jean-Marie; Gulari, Erdogan; Lahann, Joerg

    2007-07-03

    Compared with the well equipped arsenal of surface modification methods for flat surfaces, techniques that are applicable to curved, colloidal surfaces are still in their infancy. This technological gap exists because spin-coating techniques used in traditional photolithographic processes are not applicable to the curved surfaces of spherical objects. By replacing spin-coated photoresist with a vapor-deposited, photodefinable polymer coating, we have now fabricated microstructured colloids with a wide range of surface patterns, including asymmetric and chiral surface structures, that so far were typically reserved for flat substrates. This high-throughput method can yield surface-structured colloidal particles at a rate of approximately 10(7) to 10(8) particles per operator per day. Equipped with spatially defined binding pockets, microstructured colloids can engage in programmable interactions, which can lead to directed self-assembly. The ability to create a wide range of colloids with both simple and complex surface patterns may contribute to the genesis of previously unknown colloidal structures and may have important technological implications in a range of different applications, including photonic and phononic materials or chemical sensors.

  13. A multifunctional drug combination shows highly potent therapeutic efficacy against human cancer xenografts in athymic mice.

    Directory of Open Access Journals (Sweden)

    Xiu-Jun Liu

    Full Text Available The tumor microenvironment plays a crucial role during tumor development. Integrated combination of drugs that target tumor microenvironment is a promising approach to anticancer therapy. Here, we report a multifunctional combination of low-cytotoxic drugs composed of dipyridamole, bestatin and dexamethasone (DBDx which mainly acts on the tumor microenvironment shows highly potent antitumor efficacy in vivo. In mouse hepatoma H22 model, the triple drug combination showed synergistic and highly potent antitumor efficacy. The combination indices of various combinations of the triple drugs were between 0.2 and 0.5. DBDx inhibited the growth of a panel of human tumor xenografts and showed no obvious systemic toxicity. At tolerated doses, DBDx suppressed the growth of human hepatocellular carcinoma BEL-7402, HepG2, and lung adenocarcinoma A549 xenografts by 94.5%, 93.7% and 96.9%, respectively. Clonogenic assay demonstrated that DBDx showed weak cytotoxicity. Western blot showed that Flk1 and Nos3 were down-regulated in the DBDx-treated group. Proteomic analysis showed that DBDx mainly affected the metabolic process and immune system process; in addition, the angiogenesis and VEGF signaling pathway were also affected. Conclusively, DBDx, a multifunctional drug combination of three low-cytotoxic drugs, shows synergistic and highly potent antitumor efficacy evidently mediated by the modulation of tumor microenvironment. Based on its low-cytotoxic attributes and its broad-spectrum antitumor therapeutic efficacy, this multifunctional combination might be useful in the treatment of cancers, especially those refractory to conventional chemotherapeutics.

  14. Surface-exposed glycoproteins of hyperthermophilic Sulfolobus solfataricus P2 show a common N-glycosylation profile.

    Science.gov (United States)

    Palmieri, Gianna; Balestrieri, Marco; Peter-Katalinić, Jasna; Pohlentz, Gottfried; Rossi, Mosè; Fiume, Immacolata; Pocsfalvi, Gabriella

    2013-06-07

    Cell surface proteins of hyperthermophilic Archaea actively participate in intercellular communication, cellular uptake, and energy conversion to sustain survival strategies in extreme habitats. Surface (S)-layer glycoproteins, the major component of the S-layers in many archaeal species and the best-characterized prokaryotic glycoproteins, were shown to have a large structural diversity in their glycan compositions. In spite of this, knowledge on glycosylation of proteins other than S-layer proteins in Archaea is quite limited. Here, the N-glycosylation pattern of cell-surface-exposed proteins of Sulfolobus solfataricus P2 were analyzed by lectin affinity purification, HPAEC-PAD, and multiple mass spectrometry-based techniques. Detailed analysis of SSO1273, one of the most abundant ABC transporters present in the cell surface fraction of S. solfataricus, revealed a novel glycan structure composed of a branched sulfated heptasaccharide, Hex4(GlcNAc)2 plus sulfoquinovose where Hex is d-mannose and d-glucose. Having one monosaccharide unit more than the glycan of the S-layer glycoprotein of S. acidocaldarius, this is the most complex archaeal glycan structure known today. SSO1273 protein is heavily glycosylated and all 20 theoretical N-X-S/T (where X is any amino acid except proline) consensus sequence sites were confirmed. Remarkably, we show that several other proteins in the surface fraction of S. solfataricus are N-glycosylated by the same sulfated oligosaccharide and we identified 56 N-glycosylation sites in this subproteome.

  15. Root-determined hypernodulation mutant of Lotus japonicus shows high-yielding characteristics.

    Science.gov (United States)

    Yokota, Keisuke; Li, Yong Yi; Hisatomi, Masahiro; Wang, Yanxu; Ishikawa, Kaori; Liu, Chi-Te; Suzuki, Shino; Aonuma, Kho; Aono, Toshihiro; Nakamoto, Tomomi; Oyaizu, Hiroshi

    2009-07-01

    Here we report the phenotypic characteristics of a novel hypernodulation mutant, Ljrdh1 (root-determined hypernodulation 1) of Lotus japonicus. At 12 weeks after rhizobial inoculation, there were no differences between the growth of Ljrdh1 and, wild-type. However, Ljrdh1 showed 2 to 3 times higher nitrogen-fixing activity, and seed and pod yields, were approximately 50% higher than the wild-type. This is the first report of a legume hypernodulation mutant showing normal growth and a high-yielding characteristic under optimal cultivation conditions.

  16. Why do high-redshift galaxies show diverse gas-phase metallicity gradients?

    CERN Document Server

    Ma, Xiangcheng; Feldmann, Robert; Torrey, Paul; Faucher-Giguere, Claude-Andre; Keres, Dusan

    2016-01-01

    Recent spatially resolved observations of galaxies at z=0.6-3 reveal that high-redshift galaxies show complex kinematics and a broad distribution of gas-phase metallicity gradients. To understand these results, we use a suite of high-resolution cosmological zoom-in simulations from the Feedback in Realistic Environments (FIRE) project, which include physically motivated models of the multi-phase ISM, star formation, and stellar feedback. Our simulations reproduce the observed diversity of kinematic properties and metallicity gradients, broadly consistent with observations at z=0-3. Strong negative metallicity gradients only appear in galaxies with a rotating disk, but not all rotationally supported galaxies have significant gradients. Strongly perturbed galaxies with little rotation always have flat gradients. The kinematic properties and metallicity gradient of a high-redshift galaxy can vary significantly on short time-scales, associated with starburst episodes. Feedback from a starburst can destroy the gas...

  17. High-frequency gamblers show increased resistance to extinction following partial reinforcement.

    Science.gov (United States)

    Horsley, Rachel R; Osborne, Matthew; Norman, Christine; Wells, Timothy

    2012-04-15

    Behaviours that have been rewarded intermittently persist for longer during periods of non-reward than behaviours that have been rewarded continuously. This classic phenomenon is known as the partial reinforcement extinction effect. For decades it has been generally understood that this phenomenon is fundamental to the persistence of gambling in the absence of winning. One obvious, yet untested hypothesis arising from this is that persistent (here, high-frequency) gamblers might be more sensitive to partial reinforcement contingencies. Therefore, our aim was to test the hypothesis that compared to low-frequency gamblers, high-frequency gamblers would show greater resistance to extinction following partial reinforcement in a computer based experiment. Participants were 19 high-frequency gamblers and 21 low-frequency gamblers, all healthy non-smokers aged between 18 and 52. Following partial or continuous reinforcement, persistence of responding in extinction was measured as the number of times a target response was made. After partial reinforcement, high-frequency gamblers made the target response a greater number of times in extinction (compared to low-frequency gamblers). Moreover, the partial reinforcement extinction effect was larger in high-frequency gamblers than in low-frequency gamblers. It remains to be seen whether increased sensitivity to partial reinforcement is a cause or effect of persistent gambling. Nevertheless, the present study represents an important first step in investigating the role of simple partial reinforcement contingencies in determining resistance to extinction in gamblers, the importance of which, whilst hitherto recognised, has never been demonstrated experimentally.

  18. Isotopically enriched ammonium shows high nitrogen transformation in the pile top zone of dairy manure compost

    Science.gov (United States)

    Maeda, Koki; Toyoda, Sakae; Yano, Midori; Hattori, Shohei; Fukasawa, Makoto; Nakajima, Keiichi; Yoshida, Naohiro

    2016-03-01

    Nitrogen isotope ratios (δ15N) of NH4+ in dairy manure compost piles with and without bulking agent (10 % w/w) were compared to understand the effects of the use of bulking agent on nitrogen conversion during manure composting. The δ15N-NH4+ values in each of three pile zones (top, side and core) were also compared. At the end of the process, piles with bulking agent showed significantly higher δ15N values (17.7 ± 1.3 ‰) than piles without bulking agent (11.8 ± 0.9 ‰), reflecting the significantly higher nitrogen conversion and NH3 loss in the former. The samples from the top zone, especially in the piles with bulking agent, showed very high NH4+ concentrations with significantly high 15N (δ15N: 12.7-29.8 ‰) values, indicating that extremely high nitrogen conversion, nitrification-denitrification activity of the microbes and NH3 volatilization occurred in this zone.

  19. High contact angle hysteresis of superhydrophobic surfaces: Hydrophobic defects

    Science.gov (United States)

    Chang, Feng-Ming; Hong, Siang-Jie; Sheng, Yu-Jane; Tsao, Heng-Kwong

    2009-08-01

    A typical superhydrophobic surface is essentially nonadhesive and exhibits very low water contact angle (CA) hysteresis, so-called Lotus effect. However, leaves of some plants such as scallion and garlic with an advancing angle exceeding 150° show very serious CA hysteresis. Although surface roughness and epicuticular wax can explain the very high advancing CA, our analysis indicates that the unusual hydrophobic defect, diallyl disulfide, is the key element responsible for contact line pinning on allium leaves. After smearing diallyl disulfide on an extended polytetrafluoroethylene (PTFE) film, which is originally absent of CA hysteresis, the surface remains superhydrophobic but becomes highly adhesive.

  20. Why do high-redshift galaxies show diverse gas-phase metallicity gradients?

    Science.gov (United States)

    Ma, Xiangcheng; Hopkins, Philip F.; Feldmann, Robert; Torrey, Paul; Faucher-Giguère, Claude-André; Kereš, Dušan

    2017-01-01

    Recent spatially resolved observations of galaxies at z ˜ 0.6-3 reveal that high-redshift galaxies show complex kinematics and a broad distribution of gas-phase metallicity gradients. To understand these results, we use a suite of high-resolution cosmological zoom-in simulations from the Feedback in Realistic Environments (FIRE) project, which include physically motivated models of the multi-phase ISM, star formation, and stellar feedback. Our simulations reproduce the observed diversity of kinematic properties and metallicity gradients, broadly consistent with observations at z ˜ 0-3. Strong negative metallicity gradients only appear in galaxies with a rotating disk, but not all rotationally supported galaxies have significant gradients. Strongly perturbed galaxies with little rotation always have flat gradients. The kinematic properties and metallicity gradient of a high-redshift galaxy can vary significantly on short time-scales, associated with starburst episodes. Feedback from a starburst can destroy the gas disk, drive strong outflows, and flatten a pre-existing negative metallicity gradient. The time variability of a single galaxy is statistically similar to the entire simulated sample, indicating that the observed metallicity gradients in high-redshift galaxies reflect the instantaneous state of the galaxy rather than the accretion and growth history on cosmological time-scales. We find weak dependence of metallicity gradient on stellar mass and specific star formation rate (sSFR). Low-mass galaxies and galaxies with high sSFR tend to have flat gradients, likely due to the fact that feedback is more efficient in these galaxies. We argue that it is important to resolve feedback on small scales in order to produce the diverse metallicity gradients observed.

  1. Disproportionate Cochlear Length in Genus Homo Shows a High Phylogenetic Signal during Apes' Hearing Evolution.

    Science.gov (United States)

    Braga, J; Loubes, J-M; Descouens, D; Dumoncel, J; Thackeray, J F; Kahn, J-L; de Beer, F; Riberon, A; Hoffman, K; Balaresque, P; Gilissen, E

    2015-01-01

    Changes in lifestyles and body weight affected mammal life-history evolution but little is known about how they shaped species' sensory systems. Since auditory sensitivity impacts communication tasks and environmental acoustic awareness, it may have represented a deciding factor during mammal evolution, including apes. Here, we statistically measure the influence of phylogeny and allometry on the variation of five cochlear morphological features associated with hearing capacities across 22 living and 5 fossil catarrhine species. We find high phylogenetic signals for absolute and relative cochlear length only. Comparisons between fossil cochleae and reconstructed ape ancestral morphotypes show that Australopithecus absolute and relative cochlear lengths are explicable by phylogeny and concordant with the hypothetized ((Pan,Homo),Gorilla) and (Pan,Homo) most recent common ancestors. Conversely, deviations of the Paranthropus oval window area from these most recent common ancestors are not explicable by phylogeny and body weight alone, but suggest instead rapid evolutionary changes (directional selection) of its hearing organ. Premodern (Homo erectus) and modern human cochleae set apart from living non-human catarrhines and australopiths. They show cochlear relative lengths and oval window areas larger than expected for their body mass, two features corresponding to increased low-frequency sensitivity more recent than 2 million years ago. The uniqueness of the "hypertrophied" cochlea in the genus Homo (as opposed to the australopiths) and the significantly high phylogenetic signal of this organ among apes indicate its usefulness to identify homologies and monophyletic groups in the hominid fossil record.

  2. Disproportionate Cochlear Length in Genus Homo Shows a High Phylogenetic Signal during Apes' Hearing Evolution.

    Directory of Open Access Journals (Sweden)

    J Braga

    Full Text Available Changes in lifestyles and body weight affected mammal life-history evolution but little is known about how they shaped species' sensory systems. Since auditory sensitivity impacts communication tasks and environmental acoustic awareness, it may have represented a deciding factor during mammal evolution, including apes. Here, we statistically measure the influence of phylogeny and allometry on the variation of five cochlear morphological features associated with hearing capacities across 22 living and 5 fossil catarrhine species. We find high phylogenetic signals for absolute and relative cochlear length only. Comparisons between fossil cochleae and reconstructed ape ancestral morphotypes show that Australopithecus absolute and relative cochlear lengths are explicable by phylogeny and concordant with the hypothetized ((Pan,Homo,Gorilla and (Pan,Homo most recent common ancestors. Conversely, deviations of the Paranthropus oval window area from these most recent common ancestors are not explicable by phylogeny and body weight alone, but suggest instead rapid evolutionary changes (directional selection of its hearing organ. Premodern (Homo erectus and modern human cochleae set apart from living non-human catarrhines and australopiths. They show cochlear relative lengths and oval window areas larger than expected for their body mass, two features corresponding to increased low-frequency sensitivity more recent than 2 million years ago. The uniqueness of the "hypertrophied" cochlea in the genus Homo (as opposed to the australopiths and the significantly high phylogenetic signal of this organ among apes indicate its usefulness to identify homologies and monophyletic groups in the hominid fossil record.

  3. Disproportionate Cochlear Length in Genus Homo Shows a High Phylogenetic Signal during Apes’ Hearing Evolution

    Science.gov (United States)

    Braga, J.; Loubes, J-M.; Descouens, D.; Dumoncel, J.; Thackeray, J. F.; Kahn, J-L.; de Beer, F.; Riberon, A.; Hoffman, K.; Balaresque, P.; Gilissen, E.

    2015-01-01

    Changes in lifestyles and body weight affected mammal life-history evolution but little is known about how they shaped species’ sensory systems. Since auditory sensitivity impacts communication tasks and environmental acoustic awareness, it may have represented a deciding factor during mammal evolution, including apes. Here, we statistically measure the influence of phylogeny and allometry on the variation of five cochlear morphological features associated with hearing capacities across 22 living and 5 fossil catarrhine species. We find high phylogenetic signals for absolute and relative cochlear length only. Comparisons between fossil cochleae and reconstructed ape ancestral morphotypes show that Australopithecus absolute and relative cochlear lengths are explicable by phylogeny and concordant with the hypothetized ((Pan,Homo),Gorilla) and (Pan,Homo) most recent common ancestors. Conversely, deviations of the Paranthropus oval window area from these most recent common ancestors are not explicable by phylogeny and body weight alone, but suggest instead rapid evolutionary changes (directional selection) of its hearing organ. Premodern (Homo erectus) and modern human cochleae set apart from living non-human catarrhines and australopiths. They show cochlear relative lengths and oval window areas larger than expected for their body mass, two features corresponding to increased low-frequency sensitivity more recent than 2 million years ago. The uniqueness of the “hypertrophied” cochlea in the genus Homo (as opposed to the australopiths) and the significantly high phylogenetic signal of this organ among apes indicate its usefulness to identify homologies and monophyletic groups in the hominid fossil record. PMID:26083484

  4. Movement-related beta oscillations show high intra-individual reliability.

    Science.gov (United States)

    Espenhahn, Svenja; de Berker, Archy O; van Wijk, Bernadette C M; Rossiter, Holly E; Ward, Nick S

    2017-02-15

    Oscillatory activity in the beta frequency range (15-30Hz) recorded from human sensorimotor cortex is of increasing interest as a putative biomarker of motor system function and dysfunction. Despite its increasing use in basic and clinical research, surprisingly little is known about the test-retest reliability of spectral power and peak frequency measures of beta oscillatory signals from sensorimotor cortex. Establishing that these beta measures are stable over time in healthy populations is a necessary precursor to their use in the clinic. Here, we used scalp electroencephalography (EEG) to evaluate intra-individual reliability of beta-band oscillations over six sessions, focusing on changes in beta activity during movement (Movement-Related Beta Desynchronization, MRBD) and after movement termination (Post-Movement Beta Rebound, PMBR). Subjects performed visually-cued unimanual wrist flexion and extension. We assessed Intraclass Correlation Coefficients (ICC) and between-session correlations for spectral power and peak frequency measures of movement-related and resting beta activity. Movement-related and resting beta power from both sensorimotor cortices was highly reliable across sessions. Resting beta power yielded highest reliability (average ICC=0.903), followed by MRBD (average ICC=0.886) and PMBR (average ICC=0.663). Notably, peak frequency measures yielded lower ICC values compared to the assessment of spectral power, particularly for movement-related beta activity (ICC=0.386-0.402). Our data highlight that power measures of movement-related beta oscillations are highly reliable, while corresponding peak frequency measures show greater intra-individual variability across sessions. Importantly, our finding that beta power estimates show high intra-individual reliability over time serves to validate the notion that these measures reflect meaningful individual differences that can be utilised in basic research and clinical studies. Copyright © 2016 The

  5. Mannosylerythritol lipid, a yeast extracellular glycolipid, shows high binding affinity towards human immunoglobulin G

    Directory of Open Access Journals (Sweden)

    Ikegami Toru

    2001-09-01

    Full Text Available Abstract Background There have been many attempts to develop new materials with stability and high affinity towards immunoglobulins. Some of glycolipids such as gangliosides exhibit a high affinity toward immunoglobulins. However, it is considerably difficult to develop these glycolipids into the practical separation ligand due to their limited amounts. We thus focused our attention on the feasible use of "mannosylerythritol lipid A", a yeast glycolipid biosurfactant, as an alternative ligand for immunoglobulins, and undertook the investigation on the binding between mannosylerythritol lipid A (MEL-A and human immunoglobulin G (HIgG. Results In ELISA assay, MEL-A showed nearly the same binding affinity towards HIgG as that of bovine ganglioside GM1. Fab of human IgG was considered to play a more important role than Fc in the binding of HIgG by MEL-A. The bound amount of HIgG increased depending on the attached amount of MEL-A onto poly (2-hydroxyethyl methacrylate (polyHEMA beads, whereas the amount of human serum albumin slightly decreased. Binding-amount and -selectivity of HIgG towards MEL-A were influenced by salt species, salt concentration and pH in the buffer solution. The composite of MEL-A and polyHEMA, exhibited a significant binding constant of 1.43 × 106 (M-1 for HIgG, which is approximately 4-fold greater than that of protein A reported. Conclusions MEL-A shows high binding-affinity towards HIgG, and this is considered to be due to "multivalent effect" based on the binding molar ratio. This is the first report on the binding of a natural human antibody towards a yeast glycolipid.

  6. HpaA shows variable surface localization but the gene expression is similar in different Helicobacter pylori strains.

    Science.gov (United States)

    Lundström, A M; Blom, K; Sundaeus, V; Bölin, I

    2001-11-01

    Due to earlier contradictory results regarding the localization of the putative Helicobacter pylori adhesin A (HpaA), we aimed to compare the gene and protein expression and surface localization of HpaA in different H. pylori strains. Five H. pylori strains were cultivated for 11 days and analysed by Northern blot analysis, flow cytometry (FCM), semi-quantitative dot blot, colony blot, immuno-electron microscopy (IEM), and phase-contrast microscopy. The highest transcriptional activity of the hapA gene as observed after 3-4 days of cultivation and two mRNA transcripts of 1600 and 3100 nucleotides, respectively, were detected in all five strains with the hpaA probe. We also showed by reverse transcription-polymerase chain reaction (RT-PCR) that the hpaA gene is co-transcribed with the downstream omp18 gene. The highest total HpaA protein production in bacteria occurred between day 3 and 7, as determined by semi-quantitative dot blot, and was similar in the different strains. The maximal proportion of cells with HpaA on the bacterial surface, detected by FCM, was for strain SS1, 90%; Hel 344, 60%; CCUG 17875, 61%; CCUG 17874, 86% and for strain AH 244 only 35%. By IEM HpaA was detected in all strains both on the bacterial surface and on the flagellar sheath. Copyright 2001 Academic Press.

  7. Bone cells in birds show exceptional surface area, a characteristic tracing back to saurischian dinosaurs of the late Triassic.

    Directory of Open Access Journals (Sweden)

    John M Rensberger

    Full Text Available Dinosaurs are unique among terrestrial tetrapods in their body sizes, which range from less than 3 gm in hummingbirds to 70,000 kg or more in sauropods. Studies of the microstructure of bone tissue have indicated that large dinosaurs, once believed to be slow growing, attained maturity at rates comparable to or greater than those of large mammals. A number of structural criteria in bone tissue have been used to assess differences in rates of osteogenesis in extinct taxa, including counts of lines of arrested growth and the density of vascular canals.Here, we examine the density of the cytoplasmic surface of bone-producing cells, a feature which may set an upper limit to the rate of osteogenesis. Osteocyte lacunae and canaliculi, the cavities in bone containing osteocytes and their extensions, were measured in thin-sections of primary (woven and parallel fibered bone in a diversity of tetrapods. The results indicate that bone cell surfaces are more densely organized in the Saurischia (extant birds, extinct Mesozoic Theropoda and Sauropodomorpha than in other tetrapods, a result of denser branching of the cell extensions. The highest postnatal growth rates among extant tetrapods occur in modern birds, the only surviving saurischians, and the finding of exceptional cytoplasmic surface area of the cells that produce bone in this group suggests a relationship with bone growth rate. In support of this relationship is finding the lowest cell surface density among the saurischians examined in Dinornis, a member of a group of ratites that evolved in New Zealand in isolation from mammalian predators and show other evidence of lowered maturation rates.

  8. Ghrelin O-acyltransferase knockout mice show resistance to obesity when fed high-sucrose diet.

    Science.gov (United States)

    Kouno, Tetsuya; Akiyama, Nobuteru; Ito, Takahito; Okuda, Tomohiko; Nanchi, Isamu; Notoya, Mitsuru; Oka, Shogo; Yukioka, Hideo

    2016-02-01

    Ghrelin is an appetite-stimulating hormone secreted from stomach. Since the discovery that acylation of the serine-3 residue by ghrelin O-acyltransferase (GOAT) is essential for exerting its functions, GOAT has been regarded as an therapeutic target for attenuating appetite, and thus for the treatment of obesity and diabetes. However, contrary to the expectations, GOAT-knockout (KO) mice have not shown meaningful body weight reduction, under high-fat diet. Here, in this study, we sought to determine whether GOAT has a role in body weight regulation and glucose metabolism with a focus on dietary sucrose, because macronutrient composition of diet is important for appetite regulation. We found that peripherally administered acylated-ghrelin, but not unacylated one, stimulated sucrose consumption in a two-bottle-drinking test. The role of acylated-ghrelin in sucrose preference was further supported by the finding that GOAT KO mice consumed less sucrose solution compared with WT littermates. Then, we investigated the effect of dietary composition of sucrose on food intake and body weight in GOAT KO and WT mice. As a result, when fed on high-fat diet, food intake and body weight were similar between GOAT KO and WT mice. However, when fed on high-fat, high-sucrose diet, GOAT KO mice showed significantly reduced food intake and marked resistance to obesity, leading to amelioration of glucose metabolism. These results suggest that blockade of acylated-ghrelin production offers therapeutic potential for obesity and metabolic disorders caused by overeating of palatable food. © 2016 Society for Endocrinology.

  9. High surface area fibrous silica nanoparticles

    KAUST Repository

    Polshettiwar, Vivek

    2014-11-11

    Disclosed are high surface area nanoparticles that have a fibrous morphology. The nanoparticles have a plurality of fibers, wherein each fiber is in contact with one other fiber and each fiber has a length of between about 1 nm and about 5000 nm. Also disclosed are applications of the nanoparticles of the present invention, and methods of fabrication of the nanoparticles of the present invention.

  10. Surface spectroscopy using high energy heavy ions

    Energy Technology Data Exchange (ETDEWEB)

    Doyle, B.L.; Cocke, C.L.; Gray, T.J.; Justiniano, E.; Peercy, P.S.

    1983-04-01

    Surface atoms ionized by high energy heavy ions have been detected by time-of-flight and quadrupole mass spectroscopic techniques. The experimental arrangements are described and potential applications are suggested. Both techniques are demonstrated to produce significant improvements in the detection of atomic hydrogen, with the TOF method producing a nine order of magnitude increase in the sensitivity of atomic hydrogen compared to standard nuclear analysis methods.

  11. Phyllosphere Metaproteomes of Trees from the Brazilian Atlantic Forest Show High Levels of Functional Redundancy.

    Science.gov (United States)

    Lambais, M R; Barrera, S E; Santos, E C; Crowley, D E; Jumpponen, A

    2017-01-01

    The phyllosphere of the Brazilian Atlantic Forest has been estimated to contain several million bacterial species that are associated with approximately 20000 plant species. Despite the high bacterial diversity in the phyllosphere, the function of these microorganisms and the mechanisms driving their community assembly are largely unknown. In this study, we characterized the bacterial communities in the phyllospheres of four tree species of the Atlantic Forest (Mollinedia schottiana, Ocotea dispersa, Ocotea teleiandra, and Tabebuia serratifolia) and their metaproteomes to examine the basic protein functional groups expressed in the phyllosphere. Bacterial community analyses using 16S rRNA gene sequencing confirmed prior observations that plant species harbor distinct bacterial communities and that plants of the same taxon have more similar communities than more distantly related taxa. Using LC-ESI-Q-TOF, we identified 216 nonredundant proteins, based on 3503 peptide mass spectra. Most protein families were shared among the phyllosphere communities, suggesting functional redundancy despite differences in the species compositions of the bacterial communities. Proteins involved in glycolysis and anaerobic carbohydrate metabolism, solute transport, protein metabolism, cell motility, stress and antioxidant responses, nitrogen metabolism, and iron homeostasis were among the most frequently detected. In contrast to prior studies on crop plants and Arabidopsis, a low abundance of OTUs related to Methylobacterium and no proteins associated with the metabolism of one-carbon molecules were detected in the phyllospheres of the tree species studied here. Our data suggest that even though the phyllosphere bacterial communities of different tree species are phylogenetically diverse, their metaproteomes are functionally convergent with respect to traits required for survival on leaf surfaces.

  12. Analysis of allergen immunotherapy studies shows increased clinical efficacy in highly symptomatic patients

    DEFF Research Database (Denmark)

    Howarth, P; Malling, Hans-Jørgen; Molimard, M;

    2011-01-01

    To cite this article: Howarth P, Malling H-J, Molimard M, Devillier P. Analysis of allergen immunotherapy studies shows increased clinical efficacy in highly symptomatic patients. Allergy 2012; 67: 321-327. ABSTRACT: Background:  The assessment of allergen immunotherapy (AIT) efficacy...... in the treatment for seasonal allergic rhinoconjunctivitis (SAR) symptoms is challenging. Allergen immunotherapy differs from symptomatic therapy in that while symptomatic therapy treats patients after symptoms appear and aims to reduce symptoms, AIT is administered before symptoms are present and aims to prevent...... them. Thus, clinical studies of AIT can neither establish baseline symptom levels nor limit the enrolment of patients to those with the most severe symptoms. Allergen immunotherapy treatment effects are therefore diluted by patients with low symptoms for a particular pollen season. The objective...

  13. High temperature photoelectron emission and surface photovoltage in semiconducting diamond

    Science.gov (United States)

    Williams, G. T.; Cooil, S. P.; Roberts, O. R.; Evans, S.; Langstaff, D. P.; Evans, D. A.

    2014-08-01

    A non-equilibrium photovoltage is generated in semiconducting diamond at above-ambient temperatures during x-ray and UV illumination that is sensitive to surface conductivity. The H-termination of a moderately doped p-type diamond (111) surface sustains a surface photovoltage up to 700 K, while the clean (2 × 1) reconstructed surface is not as severely affected. The flat-band C 1s binding energy is determined from 300 K measurement to be 283.87 eV. The true value for the H-terminated surface, determined from high temperature measurement, is (285.2 ± 0.1) eV, corresponding to a valence band maximum lying 1.6 eV below the Fermi level. This is similar to that of the reconstructed (2 × 1) surface, although this surface shows a wider spread of binding energy between 285.2 and 285.4 eV. Photovoltage quantification and correction are enabled by real-time photoelectron spectroscopy applied during annealing cycles between 300 K and 1200 K. A model is presented that accounts for the measured surface photovoltage in terms of a temperature-dependent resistance. A large, high-temperature photovoltage that is sensitive to surface conductivity and photon flux suggests a new way to use moderately B-doped diamond in voltage-based sensing devices.

  14. Liquid Crystalline Epoxies with Lateral Substituents Showing a Low Dielectric Constant and High Thermal Conductivity

    Science.gov (United States)

    Guo, Huilong; Lu, Mangeng; Liang, Liyan; Wu, Kun; Ma, Dong; Xue, Wei

    2017-02-01

    In this work, liquid crystalline epoxies with lateral substituents were synthesized and cured with aromatic amines or anhydride. The liquid crystalline phase structure of liquid crystalline epoxies with lateral substituents was determined by polarized optical microscopy. The relationship between thermal conductivity and dielectric properties and liquid crystalline domain structure was discussed in the paper. The samples show high thermal conductivity up to 0.29 W/(m × K), due to the orientation of mesogenic units in epoxies. The sample's low dielectric constant of 2.29 is associated with the oriented mesogenic units and long nonpolar lateral substituents. This indicates a new way to obtain materials with high thermal conductivity and a low dielectric constant by introducing oriented mesogenic units into cross-linked epoxy systems. The water repellency is reflected in the contact angles of 92-98°, which are apparently higher than that of conventional epoxy systems. It was also found that the better toughness of liquid crystalline epoxies with lateral substituents was attributed to the existence of long flexible alkyl lateral substituents.

  15. Culturable associated-bacteria of the sponge Theonella swinhoei show tolerance to high arsenic concentrations

    Directory of Open Access Journals (Sweden)

    Ray eKeren

    2015-02-01

    Full Text Available Sponges are potent filter feeders and as such are exposed to high fluxes of toxic trace elements, which can accumulate in their body over time. Such is the case of the Red Sea sponge Theonella swinhoei, which has been shown to accumulate up to 8500 mg/Kg of the highly toxic element arsenic. T. swinhoei is known to harbor a multitude of sponge-associated bacteria, so it is hypothesized that the associated-bacteria will be tolerant to high arsenic concentration. This study also investigates the fate of the arsenic accumulated in the sponge to test if the associated-bacteria have an important role in the arsenic accumulation process of their host, since bacteria are key players in the natural arsenic cycle. Separation of the sponge to sponge cells and bacteria enriched fractions showed that arsenic is accumulated by the bacteria. Sponge-associated, arsenic-tolerant bacteria were cultured in the presence of 5 mM of either arsenate or arsenite (equivalent to 6150 mg/Kg arsenic, dry weight. The 54 isolated bacteria were grouped to 15 OTUs and isolates belonging to 12 OTUs were assessed for tolerance to arsenate at increased concentrations up to 100 mM. Eight of the 12 OTUs tolerated an order of magnitude increase in the concentration of arsenate, and some exhibited external biomineralization of arsenic-magnesium salts. The biomineralization of this unique mineral was directly observed in bacteria for the first time. These results may provide an explanation for the ability of the sponge to accumulate considerable amounts of arsenic. Furthermore arsenic-mineralizing bacteria can potentially be used for the study of bioremediation, as arsenic toxicity affects millions of people worldwide.

  16. Interdisciplinarity, Debate And Movie Clips As Highly Motivating Factors In Live Shows - Five Years Of Success

    Science.gov (United States)

    Stengler, E.; Sirera, J. M.

    2011-09-01

    A live show on any subject that includes experiments and continuous interaction with the audience is a well known approach for EPO activities that many are carrying out all over. We present such an initiative with some added ingredients such as interdisciplinarity, the use of movie clips, and especially the debate between the two presenters, a debate that is all the more attractive to the public if it not fully staged but closely represents their actual points of view. José Montesinos, from the "Orotava" Canarian Foundation for the History of Science, is and plays the role of the more mature math professor who has grown weary of the overrated value given in science to mathematics and its consequences. This poses a constant challenge to his colleague, Erik Stengler, from the Science Museum of Tenerife, the young down-to-earth hands-on scientist, who defends the usual view that science and technology are to be judged by their achievements, which have brought about the advancement of modern society. With this approach and as a collaboration between our institutions, we have produced and toured highly successful activities on: Einstein and Relativity (from 2005 to 2008, "Einstein Goes To School," including a theatre play); circularity, the number π, forces of inertia and the Newtonian revolution (in 2008/2009, "The Tension Between Circularity and The Straight Line"); and the foundations of modern astronomy (in 2009/2010 "Kepler and Galileo, Messengers of the Stars"). Audiences were very varied - students, adult students, general public, prison inmates, teachers - and all appreciated the presentations as fun, thought-provoking and highly motivating, and valued especially the interdisciplinary character of the activity. Movie clips have shown to be especially useful to recover the attention of the young when they lose the thread due to the short attention spans they presently have.

  17. Physical mapping of probes within 14q32, a subtelomeric region showing a high recombination frequency.

    Science.gov (United States)

    Hofker, M H; Smith, S; Nakamura, Y; Teshima, I; White, R; Cox, D W

    1990-01-01

    The genetic linkage map of chromosome 14q32 contains 11 loci which span a distance of more than 60 cM. We have assigned 10 of these loci and the AKT1 proto-oncogene to segments of 14q32, using breakpoints derived from four independent chromosomal deletions or rearrangements. The most telomeric breakpoint was found in a proband (HSC 6) carrying a ring-14 chromosome. HSC 6 is monosomic for the distal part of 14q32, which contains the immunoglobulin heavy-chain locus (IGH), and random markers D14S20, D14S19, and D14S23. Two other chromosomal breakpoints, found in probands HSC 121 and HSC 981, could not be distinguished from each other using DNA probes, although the cytogenetic breakpoints appeared to be different at 14q32.32 and 14q32.31, respectively. The region between the breakpoints of HSC 6 and HSC 121 contains AKT1, D14S1, D14S17, and D14S16. The entire telomeric band 14q32 is assumed to contain about 10% of chromosome 14, or approximately 10 Mb. The 8 most telomeric loci, including D14S1, map to 14q32.32-qter, which measures only several megabases. However, these loci span a genetic distance of 23 cM. The high recombination frequency contrasts with the observation that two of the gamma genes in the IGH constant region show a high degree of linkage disequilibrium, though 180 kb apart. This finding suggests that a telomeric localization per se does not lead to a higher recombination frequency and favors the hypothesis that the higher recombination frequency at the telomeres may be due to specific "hot spots" for recombination.

  18. High-throughput oncogene mutation profiling shows demographic differences in BRAF mutation rates among melanoma patients.

    Science.gov (United States)

    van den Hurk, Karin; Balint, Balazs; Toomey, Sinead; O'Leary, Patrick C; Unwin, Louise; Sheahan, Kieran; McDermott, Enda W; Murphy, Ian; van den Oord, Joost J; Rafferty, Mairin; FitzGerald, Dara M; Moran, Julie; Cummins, Robert; MacEneaney, Owen; Kay, Elaine W; O'Brien, Cathal P; Finn, Stephen P; Heffron, Cynthia C B B; Murphy, Michelle; Yela, Ruben; Power, Derek G; Regan, Padraic J; McDermott, Clodagh M; O'Keeffe, Allan; Orosz, Zsolt; Donnellan, Paul P; Crown, John P; Hennessy, Bryan T; Gallagher, William M

    2015-06-01

    Because of advances in targeted therapies, the clinical evaluation of cutaneous melanoma is increasingly based on a combination of traditional histopathology and molecular pathology. Therefore, it is necessary to expand our knowledge of the molecular events that accompany the development and progression of melanoma to optimize clinical management. The central objective of this study was to increase our knowledge of the mutational events that complement melanoma progression. High-throughput genotyping was adapted to query 159 known single nucleotide mutations in 33 cancer-related genes across two melanoma cohorts from Ireland (n=94) and Belgium (n=60). Results were correlated with various clinicopathological characteristics. A total of 23 mutations in 12 genes were identified, that is--BRAF, NRAS, MET, PHLPP2, PIK3R1, IDH1, KIT, STK11, CTNNB1, JAK2, ALK, and GNAS. Unexpectedly, we discovered significant differences in BRAF, MET, and PIK3R1 mutations between the cohorts. That is, cases from Ireland showed significantly lower (PBRAF(V600E) mutation rates (19%) compared with the mutation frequency observed in Belgian patients (43%). Moreover, MET mutations were detected in 12% of Irish cases, whereas none of the Belgian patients harbored these mutations, and Irish patients significantly more often (P=0.027) had PIK3R1-mutant (33%) melanoma versus 17% of Belgian cases. The low incidence of BRAF(V600E)(-) mutant melanoma among Irish patients was confirmed in five independent Irish cohorts, and in total, only 165 of 689 (24%) Irish cases carried mutant BRAF(V600E). Together, our data show that melanoma-driving mutations vary by demographic area, which has important implications for the clinical management of this disease.

  19. Single-Molecule Surface-Enhanced Raman Scattering Spectrum of Non-Resonant Aromatic Amine Showing Raman Forbidden Bands

    CERN Document Server

    Yamamoto, Yuko S; Ozaki, Yukihiro; Zhang, Zhenglong; Kozu, Tomomi; Itoh, Tamitake; Nakanishi, Shunsuke

    2016-01-01

    We present the experimentally obtained single-molecule (SM) surface-enhanced Raman scattering (SERS) spectrum of 4-aminibenzenethiol (4-ABT), also known as para-aminothiophenol (PATP). Measured at a 4-ABT concentration of 8 * 10^-10 M, the spectra show Raman forbidden modes. The SM-SERS spectrum of 4-ABT obtained using a non-resonant visible laser is different from the previously reported SERS spectra of 4-ABT, and could not be reconstructed using quantum mechanical calculations. Careful classical assignments (not based on quantum-mechanical calculations) are reported, and indicate that differences in the reported spectra of 4-ABT are mainly due to the appearance of Raman forbidden bands. The presence of Raman forbidden bands can be explained by the charge-transfer (CT) effect of 4-ABT adsorbed on the silver nanostructures, indicating a breakdown of Raman selection rules at the SERS hotspot.

  20. In vivo high-resolution 7 Tesla MRI shows early and diffuse cortical alterations in CADASIL.

    Science.gov (United States)

    De Guio, François; Reyes, Sonia; Vignaud, Alexandre; Duering, Marco; Ropele, Stefan; Duchesnay, Edouard; Chabriat, Hugues; Jouvent, Eric

    2014-01-01

    Recent data suggest that early symptoms may be related to cortex alterations in CADASIL (Cerebral Autosomal-Dominant Arteriopathy with Subcortical Infarcts and Leukoencephalopathy), a monogenic model of cerebral small vessel disease (SVD). The aim of this study was to investigate cortical alterations using both high-resolution T2* acquisitions obtained with 7 Tesla MRI and structural T1 images with 3 Tesla MRI in CADASIL patients with no or only mild symptomatology (modified Rankin's scale ≤1 and Mini Mental State Examination (MMSE) ≥24). Complete reconstructions of the cortex using 7 Tesla T2* acquisitions with 0.7 mm isotropic resolution were obtained in 11 patients (52.1±13.2 years, 36% male) and 24 controls (54.8±11.0 years, 42% male). Seven Tesla T2* within the cortex and cortical thickness and morphology obtained from 3 Tesla images were compared between CADASIL and control subjects using general linear models. MMSE, brain volume, cortical thickness and global sulcal morphology did not differ between groups. By contrast, T2* measured by 7 Tesla MRI was significantly increased in frontal, parietal, occipital and cingulate cortices in patients after correction for multiple testing. These changes were not related to white matter lesions, lacunes or microhemorrhages in patients having no brain atrophy compared to controls. Seven Tesla MRI, by contrast to state of the art post-processing of 3 Tesla acquisitions, shows diffuse T2* alterations within the cortical mantle in CADASIL whose origin remains to be determined.

  1. Isotopically enriched ammonium shows high nitrogen transformation in the pile top zone of dairy manure compost

    Directory of Open Access Journals (Sweden)

    K. Maeda

    2016-03-01

    significantly high 15N (δ15N: 12.7–29.8 ‰ values, indicating that extremely high nitrogen conversion, nitrification–denitrification activity of the microbes and NH3 volatilization occurred in this zone.

  2. High male chimerism in the female breast shows quantitative links with cancer.

    Science.gov (United States)

    Dhimolea, Eugen; Denes, Viktoria; Lakk, Monika; Al-Bazzaz, Sana; Aziz-Zaman, Sonya; Pilichowska, Monika; Geck, Peter

    2013-08-15

    Clinical observations suggest that pregnancy provides protection against cancer. The mechanisms involved, however, remain unclear. Fetal cells are known to enter the mother's circulation during pregnancy and establish microchimerism. We investigated if pregnancy-related embryonic/fetal stem cell integration plays a role in breast cancer. A high-sensitivity Y-chromosome assay was developed to trace male allogeneic cells (from male fetus) in females. Fixed-embedded samples (n = 206) from both normal and breast cancer patients were screened for microchimerism. The results were combined with matching clinicopathological and histological parameters and processed statistically. The results show that in our samples (182 informative) more than half of healthy women (56%) carried male cells in their breast tissue for decades (n = 68), while only one out of five in the cancer sample pool (21%) (n = 114) (odds ratio = 4.75, CI at 95% 2.34-9.69; p = 0.0001). The data support the notion that a biological link may exist between chimerism and tissue-integrity. The correlation, however, is non-linear, since male microchimerism in excess ("hyperchimerism") is also involved in cancer. The data suggest a link between hyperchimerism and HER2-type cancers, while decreased chimerism ("hypochimerism") associates with ER/PR-positive (luminal-type) breast cancers. Chimerism levels that correlate with protection appear to be non-random and share densities with the mammary progenitor components of the stem cell lineage in the breast. The results suggest that protection may involve stem/progenitor level interactions and implicate novel quantitative mechanisms in chimerism biology. Copyright © 2013 UICC.

  3. In vivo high-resolution 7 Tesla MRI shows early and diffuse cortical alterations in CADASIL.

    Directory of Open Access Journals (Sweden)

    François De Guio

    Full Text Available Recent data suggest that early symptoms may be related to cortex alterations in CADASIL (Cerebral Autosomal-Dominant Arteriopathy with Subcortical Infarcts and Leukoencephalopathy, a monogenic model of cerebral small vessel disease (SVD. The aim of this study was to investigate cortical alterations using both high-resolution T2* acquisitions obtained with 7 Tesla MRI and structural T1 images with 3 Tesla MRI in CADASIL patients with no or only mild symptomatology (modified Rankin's scale ≤1 and Mini Mental State Examination (MMSE ≥24.Complete reconstructions of the cortex using 7 Tesla T2* acquisitions with 0.7 mm isotropic resolution were obtained in 11 patients (52.1±13.2 years, 36% male and 24 controls (54.8±11.0 years, 42% male. Seven Tesla T2* within the cortex and cortical thickness and morphology obtained from 3 Tesla images were compared between CADASIL and control subjects using general linear models.MMSE, brain volume, cortical thickness and global sulcal morphology did not differ between groups. By contrast, T2* measured by 7 Tesla MRI was significantly increased in frontal, parietal, occipital and cingulate cortices in patients after correction for multiple testing. These changes were not related to white matter lesions, lacunes or microhemorrhages in patients having no brain atrophy compared to controls.Seven Tesla MRI, by contrast to state of the art post-processing of 3 Tesla acquisitions, shows diffuse T2* alterations within the cortical mantle in CADASIL whose origin remains to be determined.

  4. The fire ant social chromosome supergene variant Sb shows low diversity but high divergence from SB.

    Science.gov (United States)

    Pracana, Rodrigo; Priyam, Anurag; Levantis, Ilya; Nichols, Richard A; Wurm, Yannick

    2017-02-21

    Variation in social behavior is common yet little is known about the genetic architectures underpinning its evolution. A rare exception is in the fire ant Solenopsis invicta: Alternative variants of a supergene region determine whether a colony will have exactly one or up to dozens of queens. The two variants of this region are carried by a pair of "social chromosomes", SB and Sb, which resemble a pair of sex chromosomes. Recombination is suppressed between the two chromosomes in the supergene region. While the X-like SB can recombine with itself in SB/SB queens, recombination is effectively absent in the Y-like Sb because Sb/Sb queens die before reproducing. Here, we analyze whole genome sequences of eight haploid SB males and eight haploid Sb males. We find extensive SB-Sb di↵erentiation throughout the >19Mb long supergene region. We find no evidence of "evolutionary strata" with different levels of divergence comparable to those reported in several sex chromosomes. A high proportion of substitutions between the SB and Sb haplotypes are nonsynonymous, suggesting inefficacy of purifying selection in Sb sequences, similar to that for Y-linked sequences in XY systems. Finally, we show that the Sb haplotype of the supergene region has 635-fold less nucleotide diversity than the rest of the genome. We discuss how this reduction could be due to a recent selective sweep affecting Sb specifically or associated with a population bottleneck during the invasion of North America by the sampled population. This article is protected by copyright. All rights reserved.

  5. Study Shows Aspirin Reduces Colorectal Cancer in Those at High Risk

    Science.gov (United States)

    Findings from the first large clinical trial of its kind indicate that taking high doses of aspirin daily for at least 2 years substantially reduces the risk of colorectal cancer among people at increased risk of the disease.

  6. Mannosylerythritol lipid, a yeast extracellular glycolipid, shows high binding affinity towards human immunoglobulin G

    OpenAIRE

    Ikegami Toru; Yanagishita Hiroshi; Nakane Takashi; Im Jae Hong; Kitamoto Dai

    2001-01-01

    Abstract Background There have been many attempts to develop new materials with stability and high affinity towards immunoglobulins. Some of glycolipids such as gangliosides exhibit a high affinity toward immunoglobulins. However, it is considerably difficult to develop these glycolipids into the practical separation ligand due to their limited amounts. We thus focused our attention on the feasible use of "mannosylerythritol lipid A", a yeast glycolipid biosurfactant, as an alternative ligand...

  7. Turbulent Flow past High Temperature Surfaces

    Science.gov (United States)

    Mehmedagic, Igbal; Thangam, Siva; Carlucci, Pasquale; Buckley, Liam; Carlucci, Donald

    2014-11-01

    Flow over high-temperature surfaces subject to wall heating is analyzed with applications to projectile design. In this study, computations are performed using an anisotropic Reynolds-stress model to study flow past surfaces that are subject to radiative flux. The model utilizes a phenomenological treatment of the energy spectrum and diffusivities of momentum and heat to include the effects of wall heat transfer and radiative exchange. The radiative transport is modeled using Eddington approximation including the weighted effect of nongrayness of the fluid. The time-averaged equations of motion and energy are solved using the modeled form of transport equations for the turbulence kinetic energy and the scalar form of turbulence dissipation with an efficient finite-volume algorithm. The model is applied for available test cases to validate its predictive capabilities for capturing the effects of wall heat transfer. Computational results are compared with experimental data available in the literature. Applications involving the design of projectiles are summarized. Funded in part by U.S. Army, ARDEC.

  8. Nanoscale anatase TiO{sub 2} with dominant {1 1 1} facets shows high photocatalytic activity

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Jun, E-mail: zhangj@hdu.edu.cn [College of Materials and Environmental Engineering, Hangzhou Dianzi University, Hangzhou 310018 (China); Qian, Lisha [School of Electronics and Information, Hangzhou Dianzi University, Hangzhou 310018 (China); Yang, Lingxia; Tao, Xi; Su, Kunpeng [College of Materials and Environmental Engineering, Hangzhou Dianzi University, Hangzhou 310018 (China); Wang, Hongbo [College of Automation, Hangzhou Dianzi University, Hangzhou 310018 (China); Xi, Junhua [College of Materials and Environmental Engineering, Hangzhou Dianzi University, Hangzhou 310018 (China); State Key Lab of Silicon Materials, Zhejiang University, Hangzhou 310018 (China); Ji, Zhenguo [College of Materials and Environmental Engineering, Hangzhou Dianzi University, Hangzhou 310018 (China); State Key Lab of Silicon Materials, Zhejiang University, Hangzhou 310018 (China); School of Electronics and Information, Hangzhou Dianzi University, Hangzhou 310018 (China)

    2014-08-30

    Graphical abstract: Nanoscale anatase TiO{sub 2} with exposed {1 1 1} facets was synthesized and show higher photocatalytic activity than TiO{sub 2} nanosheets with exposed {0 0 1} facets and Degussa P25. - Highlights: • Nanoscale anatase TiO{sub 2} with exposed {1 1 1} facets was obtained. • A one-step hydrothermal progress was employed to synthesize samples. • {1 1 1} facets have a higher photocatalytic activity than {0 0 1} and {1 0 1} facets. • The highest active of {1 1 1} facets is due to the specific surface structure. - Abstract: In this work, we report a novel synthesis of nanoscale anatase TiO{sub 2} with dominant highly active {1 1 1} facets by a simple one-step hydrothermal route with the assistance of NH{sub 4}F and HF. In this progress, the exposed crystal facets of TiO{sub 2} can been directly tuned by controlling the mole ratio of NH{sub 4}{sup +} and F{sup −}. When the mole ratio of NH{sub 4}{sup +} and F{sup −}reach 1:2, nanoscale anatase TiO{sub 2} with dominant {1 1 1} facets can be obtained. Nanoscale anatase TiO{sub 2} with exposed {1 0 1} or {0 0 1} facets will be prepared when there is only ammonia or HF added respectively. Such nano-TiO{sub 2} with exposed highly active {1 1 1} facets has large specific surface area and shows excellent photocatalytic activity: as much as 2–3 times than that of TiO{sub 2} nanosheets with exposed {0 0 1} facets and commercial Degussa P25 which confirms the {1 1 1} facets have higher photocatalytic activity than {0 0 1} and {1 0 1} facets. The higher photocatalytic activity of {1 1 1} facets can be ascribed to the fact that all Ti and O atoms on the surface are unsaturated Ti{sub 5c}, Ti{sub 3c} and O{sub 2c} modes which produces a higher adsorption and degradation ability. The present work demonstrates a explore of hydrothermal synthetic method for controlling preparation of nano-materials.

  9. Pd-Pt Alloy with Coral-Like Nanostructures Showing High Performance for Oxygen Electrocatalytic Reduction.

    Science.gov (United States)

    Liu, Xing-Quan; Chen, Xue-Song; Wu, Jian; Yao, Lei

    2016-03-01

    Three-dimensional (3D) Pd-Pt alloy with coral-like nanostructures were synthesized via bubble dynamic templated electrodeposition method at room temperature. The morphology of the as-prepared nanostructures was characterized using scanning electron microscopy (SEM), EDS, high-resolution transmission electron microscopy (HRTEM), respectively. Cyclic voltammetry method was adopted to evaluate the electrocatalytic activities of the synthesized electrodes toward oxygen reduction in KCl solution. The electrochemical results indicated that the Pd-Pt alloy with coral-like nanostructures hold the high performance for oxygen reduction.

  10. Phosphasalen indium complexes showing high rates and isoselectivities in rac-lactide polymerizations

    Energy Technology Data Exchange (ETDEWEB)

    Myers, Dominic; White, Andrew J.P. [Department of Chemistry, Imperial College London (United Kingdom); Forsyth, Craig M. [School of Chemistry, Monash University, Clayton, VIC (Australia); Bown, Mark [CSIRO Manufacturing, Bayview Avenue, Clayton, VIC (Australia); Williams, Charlotte K. [Department of Chemistry, Oxford University (United Kingdom)

    2017-05-02

    Polylactide (PLA) is the leading bioderived polymer produced commercially by the metal-catalyzed ring-opening polymerization of lactide. Control over tacticity to produce stereoblock PLA, from rac-lactide improves thermal properties but is an outstanding challenge. Here, phosphasalen indium catalysts feature high rates (30±3 m{sup -1} min{sup -1}, THF, 298 K), high control, low loadings (0.2 mol %), and isoselectivity (P{sub i}=0.92, THF, 258 K). Furthermore, the phosphasalen indium catalysts do not require any chiral additives. (copyright 2017 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

  11. Chicken skin virome analyzed by high-throughput sequencing shows a composition highly different from human skin.

    Science.gov (United States)

    Denesvre, Caroline; Dumarest, Marine; Rémy, Sylvie; Gourichon, David; Eloit, Marc

    2015-10-01

    Recent studies show that human skin at homeostasis is a complex ecosystem whose virome include circular DNA viruses, especially papillomaviruses and polyomaviruses. To determine the chicken skin virome in comparison with human skin virome, a chicken swabs pool sample from fifteen indoor healthy chickens of five genetic backgrounds was examined for the presence of DNA viruses by high-throughput sequencing (HTS). The results indicate a predominance of herpesviruses from the Mardivirus genus, coming from either vaccinal origin or presumably asymptomatic infection. Despite the high sensitivity of the HTS method used herein to detect small circular DNA viruses, we did not detect any papillomaviruses, polyomaviruses, or circoviruses, indicating that these viruses may not be resident of the chicken skin. The results suggest that the turkey herpesvirus is a resident of chicken skin in vaccinated chickens. This study indicates major differences between the skin viromes of chickens and humans. The origin of this difference remains to be further studied in relation with skin physiology, environment, or virus population dynamics.

  12. Breeding for improved potato nutrition: High amylose starch potatoes show promise as fiber source

    Science.gov (United States)

    Potato starch is composed of approximately 75% amylopectin and 25% amylose. We are interested in breeding for higher amylose content, which would increase the fiber content of potato and decrease glycemic index. In order to make progress in a breeding program, we have developed a high throughput ass...

  13. Polar Ketone-Functionalized Metal-Organic Framework Showing a High CO2 Adsorption Performance.

    Science.gov (United States)

    Feng, Genfeng; Peng, Yuxin; Liu, Wei; Chang, Feifan; Dai, Yafei; Huang, Wei

    2017-03-06

    The incorporation of various functionalities into porous metal-organic frameworks (MOFs) represents an efficacious strategy to improving their gas adsorption properties. In this work, a carbonylated tetracarboxylic acid ligand (5,5'-carbonyldiisophthalic acid) was synthesized, and a ketone-functionalized MOF with exposed metal sites based on this ligand was formed successfully. Structural analysis reveals that the new MOF possesses channels decorated by the carbonyl groups and rhombicuboctahedral cages, with open Cu(II) sites pointing toward the cage center. The framework exhibits exceptionally high CO2 (46.7 wt % at 273 K and 1 bar) and H2 (2.8 wt % at 77 K and 1 bar) uptake. Furthermore, it displays high selectivities of CO2 adsorption over N2 and CH4 at 298 K.

  14. High-resolution Greenland Ice Core data show abrupt climate change happens in few years

    DEFF Research Database (Denmark)

    Steffensen, Jørgen Peder; Andersen, Katrine Krogh; Bigler, Matthias

    2008-01-01

    The last two abrupt warmings at the onset of our present warm interglacial period, interrupted by the Younger Dryas cooling event, were investigated at high temporal resolution from the North Greenland Ice Core Project ice core. The deuterium excess, a proxy of Greenland precipitation moisture......, reflecting the wetting of Asian deserts. A northern shift of the Intertropical Convergence Zone could be the trigger of these abrupt shifts of Northern Hemisphere atmospheric circulation, resulting in changes of 2 to 4 kelvin in Greenland moisture source temperature from one year to the next....

  15. Chromobacterium spp. harbour Ambler class A beta-lactamases showing high identity with KPC

    DEFF Research Database (Denmark)

    Gudeta, Dereje Dadi; Bortolaia, Valeria; Jayol, Aurelie

    2016-01-01

    Objectives: The origin of KPC is unknown. The aim of this study was to detect progenitors of KPC in silico and to functionally verify their beta-lactam hydrolysis activity. Methods: The sequence of KPC-2 was used to mine the NCBI protein sequence database. The best non-KPC hits were analysed by a......-lactamases with up to 76% aa identity to KPC from distinct Chromobacterium species is highly indicative of the role played by this genus in the evolution of KPC....

  16. Pilot Study to Show the Feasibility of High-Resolution Sagittal Ultrasound Imaging of the Temporomandibular Joint.

    Science.gov (United States)

    Katzberg, Richard W; Conway, William F; Ackerman, Susan J; Gonzales, Theresa S; Kheyfits, Valeriy; Cronan, Michael S

    2017-06-01

    To show the feasibility of acquiring high-resolution sagittal ultrasound (US) images of the temporomandibular joint (TMJ). We used commercially available US probes to assess the TMJ via a transoral soft tissue window to acquire sagittal images. Magnetic resonance imaging and clinical correlation were compared with the US findings by the consensus assessment of 2 of the senior investigators. The sample was composed of 10 TMJs (6 participants) with an age range of 34 to 71 years and a male-female ratio of 3:1. The condyle and subcondylar surface were visible in 10 of 10 joints (100%), the disc in 7 of 10 joints (70%), and the pterygoid muscles in 6 of 10 joints (60%). In the 5 joints with magnetic resonance correlation, disc position and configuration were confirmed in all cases. We show the first sagittal transoral sonograms of the TMJ disc and associated joint components. Copyright © 2016 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.

  17. One novel quinoxaline derivative as a potent human cyclophilin A inhibitor shows highly inhibitory activity against mouse spleen cell proliferation.

    Science.gov (United States)

    Li, Jian; Chen, Jing; Zhang, Li; Wang, Feng; Gui, Chunshan; Zhang, Li; Qin, Yu; Xu, Qiang; Liu, Hong; Nan, Fajun; Shen, Jingkang; Bai, Donglu; Chen, Kaixian; Shen, Xu; Jiang, Hualiang

    2006-08-15

    Cyclophilin A (CypA) is a ubiquitous cellular enzyme playing critical roles in many biological processes, and its inhibitor has been reported to have potential immunosuppressive activity. In this work, we reported a novel quinoxaline derivative, 2,3-di(furan-2-yl)-6-(3-N,N-diethylcarbamoyl-piperidino)carbonylamino quinoxaline (DC838, 3), which was confirmed to be a potent inhibitor against human CypA. By using the surface plasmon resonance (SPR) and fluorescence titration techniques, the kinetic analysis of CypA/DC838 interaction was quantitatively performed. CypA peptidyl prolyl cis-trans isomerase (PPIase) activity inhibition assay showed that DC838 demonstrated highly CypA PPIase inhibitory activity. In vivo assay results showed that DC838 could inhibit mouse spleen cell proliferation induced by concanavalin A (Con A). Molecular docking simulation further elucidated the specific DC838 binding to CypA at the atomic level. The current work should provide useful information in the discovery of immunosuppressor based on CypA inhibitor.

  18. Biochemical characterization of a first fungal esterase from Rhizomucor miehei showing high efficiency of ester synthesis.

    Directory of Open Access Journals (Sweden)

    Yu Liu

    Full Text Available BACKGROUND: Esterases with excellent merits suitable for commercial use in ester production field are still insufficient. The aim of this research is to advance our understanding by seeking for more unusual esterases and revealing their characterizations for ester synthesis. METHODOLOGY/PRINCIPAL FINDINGS: A novel esterase-encoding gene from Rhizomucor miehei (RmEstA was cloned and expressed in Escherichia coli. Sequence analysis revealed a 975-bp ORF encoding a 324-amino-acid polypeptide belonging to the hormone-sensitive lipase (HSL family IV and showing highest similarity (44% to the Paenibacillus mucilaginosus esterase/lipase. Recombinant RmEstA was purified to homogeneity: it was 34 kDa by SDS-PAGE and showed optimal pH and temperature of 6.5 and 45°C, respectively. The enzyme was stable to 50°C, under a broad pH range (5.0-10.6. RmEstA exhibited broad substrate specificity toward p-nitrophenol esters and short-acyl-chain triglycerols, with highest activities (1,480 U mg(-1 and 228 U mg(-1 for p-nitrophenyl hexanoate and tributyrin, respectively. RmEstA efficiently synthesized butyl butyrate (92% conversion yield when immobilized on AOT-based organogel. CONCLUSION: RmEstA has great potential for industrial applications. RmEstA is the first reported esterase from Rhizomucor miehei.

  19. Colorectal cancers with aneuploids show high CD133 expression and poor prognosis

    Institute of Scientific and Technical Information of China (English)

    Dongdong Yu; Yonghong Zhang; You Zou; Ming Tian; Deding Tao; Junbo Hu; Jianping Gong

    2010-01-01

    Objective:The aim of the study was to investigate the relationship of DNA ploidy status in colorectal cancers with patients' prognosis and also the relationship of DNA ploidy status with expression of the colorectal cancer stem cell marker CD133.Methods:The DNA ploidy status and CD133 expression in colorectal cancers were detected by flow cytometry.The clinicopathological characteristics and progression-free survival analysis of patients was evaluated based on the clinical data.Results:DNA ploidy pattern did not correlated with gender,age,lesion diameter,histological type,depth of tumor invasion,lymphatic invasion and Dukes stage.Only primary lesion cite showed significant correlation with DNA ploidy pattern,more aneuploids were observed in colonic cancer than rectal cancer,P < 0.05.The 2-year progression-free survival rate and total progression-free time in patients with aneuploids were lower than that with diploids,P < 0.05.Tumors contained aneuploids showed higher expression of CD133 than tumors of only diploids,P < 0.05.Conclusion:Tumor DNA ploidy status is a significant prognostic factor in patients with colorectal cancer and also associated with the existence of CD133 positive colorectal cancer stem cells.

  20. Locating landmarks on high-dimensional free energy surfaces.

    Science.gov (United States)

    Chen, Ming; Yu, Tang-Qing; Tuckerman, Mark E

    2015-03-17

    Coarse graining of complex systems possessing many degrees of freedom can often be a useful approach for analyzing and understanding key features of these systems in terms of just a few variables. The relevant energy landscape in a coarse-grained description is the free energy surface as a function of the coarse-grained variables, which, despite the dimensional reduction, can still be an object of high dimension. Consequently, navigating and exploring this high-dimensional free energy surface is a nontrivial task. In this paper, we use techniques from multiscale modeling, stochastic optimization, and machine learning to devise a strategy for locating minima and saddle points (termed "landmarks") on a high-dimensional free energy surface "on the fly" and without requiring prior knowledge of or an explicit form for the surface. In addition, we propose a compact graph representation of the landmarks and connections between them, and we show that the graph nodes can be subsequently analyzed and clustered based on key attributes that elucidate important properties of the system. Finally, we show that knowledge of landmark locations allows for the efficient determination of their relative free energies via enhanced sampling techniques.

  1. Tooth enamel oxygen “isoscapes” show a high degree of human mobility in prehistoric Britain

    Science.gov (United States)

    Pellegrini, Maura; Pouncett, John; Jay, Mandy; Pearson, Mike Parker; Richards, Michael P.

    2016-10-01

    A geostatistical model to predict human skeletal oxygen isotope values (δ18Op) in Britain is presented here based on a new dataset of Chalcolithic and Early Bronze Age human teeth. The spatial statistics which underpin this model allow the identification of individuals interpreted as ‘non-local’ to the areas where they were buried (spatial outliers). A marked variation in δ18Op is observed in several areas, including the Stonehenge region, the Peak District, and the Yorkshire Wolds, suggesting a high degree of human mobility. These areas, rich in funerary and ceremonial monuments, may have formed focal points for people, some of whom would have travelled long distances, ultimately being buried there. The dataset and model represent a baseline for future archaeological studies, avoiding the complex conversions from skeletal to water δ18O values-a process known to be problematic.

  2. Decarbonizing urban transport in European cities: four cases show possibly high co-benefits

    Science.gov (United States)

    Creutzig, Felix; Mühlhoff, Rainer; Römer, Julia

    2012-12-01

    Cities worldwide are increasingly becoming agents of climate change mitigation, while simultaneously aiming for other goals, such as improved accessibility and clean air. Based on stakeholder interviews and data analysis, we assess the current state of urban mobility in the four European cities of Barcelona, Malmö, Sofia and Freiburg. We then provide scenarios of increasingly ambitious policy packages, reducing greenhouse gas emissions from urban transport by up to 80% from 2010 to 2040. We find significant concurrent co-benefits in cleaner air, reduced noise ambience, fewer traffic-related injuries and deaths, more physical activity, less congestion and monetary fuel savings. Our scenarios suggest that non-motorized transport, especially bicycles, can occupy high modal shares, particularly in cities with less than 0.5 million inhabitants. We think that this kind of multi-criteria assessment of social costs and benefits is a useful complement to cost-benefit analysis of climate change mitigation measures.

  3. Peripubertal female athletes in high-impact sports show improved bone mass acquisition and bone geometry.

    Science.gov (United States)

    Maïmoun, Laurent; Coste, Olivier; Philibert, Pascal; Briot, Karine; Mura, Thibault; Galtier, Florence; Mariano-Goulart, Denis; Paris, Françoise; Sultan, Charles

    2013-08-01

    Intensive physical training may have a sport-dependent effect on bone mass acquisition. This cross-sectional study evaluated bone mass acquisition in girls practicing sports that put different mechanical loads on bone. Eighty girls from 10.7 to 18.0 years old (mean 13.83 ± 1.97) were recruited: 20 artistic gymnasts (AG; high-impact activity), 20 rhythmic gymnasts (RG; medium-impact activity), 20 swimmers (SW, no-impact activity), and 20 age-matched controls (CON; leisure physical activity activity clearly had a favorable effect on aBMD and bone geometry during the growth period, although the bone health benefits seem to be more marked after menarche. Copyright © 2013 Elsevier Inc. All rights reserved.

  4. Assembly of three coordination polymers based on a sulfonic-carboxylic ligand showing high proton conductivity.

    Science.gov (United States)

    Zhao, Shu-Na; Song, Xue-Zhi; Zhu, Min; Meng, Xing; Wu, Lan-Lan; Song, Shu-Yan; Wang, Cheng; Zhang, Hong-Jie

    2015-01-21

    Three new coordination polymers (CPs)/metal-organic frameworks (MOFs) with different structures have been synthesized using 4,8-disulfonyl-2,6-naphthalenedicarboxylic acid (H4L) and metal ions, Cu(2+), Ca(2+) and Cd(2+). The Cu compound features a one-dimensional chain structure, further extending into a 2D layer network through H-bond interactions. Both the Ca and Cd compounds show 3D frameworks with (4,4)-connected PtS-type topology and (3,6)-connected bct-type topology, respectively. These CPs/MOFs all exhibit proton conduction behavior, especially for the Cu compound with a proton conductivity of 3.46 × 10(-3) S cm(-1) at 368 K and 95% relative humidity (RH). Additionally, the activation energy (Ea) has also been investigated to deeply understand the proton-conduction mechanism.

  5. Synchronized High-Resolution Lacustrine Records in Iceland show Non-Linear Response to Holocene Insolation

    Science.gov (United States)

    Geirsdottir, A.; Miller, G. H.; Larsen, D. J.; Thordarson, T.; Ólafsdóttir, S.; Stoner, J. S.

    2010-12-01

    Icelandic lakes commonly have sedimentation rates in excess of 1 m ka-1 through the Holocene, offering the potential for records of environmental change at decadal or better resolution. Icelandic lake sediment contains numerous volcanic tephra layers of known age, which together with high-resolution sediment paleomagnetic secular variations (PSV) allow synchronization of sediment cores from both lacustrine and marine archives. We present synchronized high-resolution paleoclimatic records from two Icelandic lakes with very different catchment characteristics. By combining PSV records and key tephra tie points we are able to synchronize the lacustrine records with each other and with a well-dated marine core from the shelf north of Iceland. The large PSV signal that characterizes the Icelandic Holocene records allows 40 to 60 secure tie points over the past 10 ka of sediment records. The high frequency of tie points allows the reconstruction of sediment accumulation rate changes in the lacustrine records that were not apparent from the tephrochonological controls. The first order trends in the lacustine climate proxies (BSi and TOC) are similar. BSi climbs to a maximum value shortly after 8 ka, then declines toward present, reflecting a relatively late Holocene thermal maximum, lagging the Greenland ice core record by ca. 2 ka. The peak of the HTM in Iceland was warm enough to melt glaciers completely with temperatures estimated to have been 3.5°C higher relative to 1960-1990 averages. Decreasing summer insolation is reflected not by gradual cooling after the HTM, but by incremental changes in state. TOC and BSi track each other during warm times, but diverge, and sedimentation rates increase, during perturbations and cold times at 8.4 ka, 5.5 ka, 4.3 to 4 ka, 3.1 ka to 2.8 ka. Following these departures, BSi usually exhibits a step-function change, re-equilibrating at a lower BSi value. Some of the departures may be related to Icelandic volcanism influencing

  6. High percentage of New Zealand white mice show anti-DNA antibodies

    Energy Technology Data Exchange (ETDEWEB)

    Lacy, M.J.; Voss, E.W. Jr.

    1986-03-01

    Autoimmune anti-nDNA activity was detected in sera of 57% of New Zealand White (NZW) mice tested. This percentage was established for anti-DNA positive females as a percent of total female NZW tested, and was identical for male NZW. Anti-DNA positive mice ranged in age from 137 days to 619 days, compared to an age range for anti-DNA negative NZW of 137 days to 523 days. Total NZW mice tested was 40. This compared to 40% anti-DNA positive sera of 59 (NZB x NZW) F/sub 1/ mice (BW), ranging in age from 218 to 345 days which were predominantly male (95%). Only 65% of NZW tested were male. Positive sera were established as those sera at a 1:10 dilution, that showed 6X or greater the background activity of sera of non-autoimmune Balb/cV mice at any concentration. All sera were assayed by a solid phase radioimmunoassay using /sup 125/I radiolabelled protein A, and therefore, reflect protein A binding isotypes only. These data implicate NZW mice significantly in the anti-DNA activity exhibited by their autoimmune BW progeny.

  7. Hydroxyeicosapentaenoic acids from the Pacific krill show high ligand activities for PPARs.

    Science.gov (United States)

    Yamada, Hidetoshi; Oshiro, Eriko; Kikuchi, Sayaka; Hakozaki, Mayuka; Takahashi, Hideyuki; Kimura, Ken-Ichi

    2014-05-01

    PPARs regulate the expression of genes for energy metabolism in a ligand-dependent manner. PPARs can influence fatty acid oxidation, the level of circulating triglycerides, glucose uptake and insulin sensitivity. Here, we demonstrate that 5-hydroxyeicosapentaenoic acid (HEPE), 8-HEPE, 9-HEPE, 12-HEPE and 18-HEPE (hydroxylation products of EPA) obtained from methanol extracts of Pacific krill (Euphausia pacifica) can act as PPAR ligands. Two of these products, 8-HEPE and 9-HEPE, enhanced the transcription levels of GAL4-PPARs to a significantly greater extent than 5-HEPE, 12-HEPE, 18-HEPE, EPA, and EPA ethyl-ester. 8-HEPE also activated significantly higher transcription of GAL4-PPARα, GAL4-PPARγ, and GAL4-PPARδ than EPA at concentrations greater than 4, 64, and 64 μM, respectively. We also demonstrated that 8-HEPE increased the expression levels of genes regulated by PPARs in FaO, 3T3-F442A, and C2C12 cells. Furthermore, 8-HEPE enhanced adipogenesis and glucose uptake. By contrast, at the same concentrations, EPA showed weak or little effect, indicating that 8-HEPE was the more potent inducer of physiological effects.

  8. High directivity optical antenna substrates for surface enhanced Raman scattering.

    Science.gov (United States)

    Wang, Dongxing; Zhu, Wenqi; Chu, Yizhuo; Crozier, Kenneth B

    2012-08-22

    A two-dimensional array of gold optical antennas integrated with a one-dimensional array of gold strips and mirrors is introduced and fabricated. The experimental results show that this design achieves average surface-enhanced Raman scattering (SERS) enhancement factors as high as 1.2 × 10(10) , which is more than two orders of magnitude larger than optical antennas without the gold strips and gold mirror.

  9. Ocean acidification shows negligible impacts on high-latitude bacterial community structure in coastal pelagic mesocosms

    Directory of Open Access Journals (Sweden)

    A.-S. Roy

    2012-09-01

    Full Text Available The impact of ocean acidification and carbonation on microbial community structure was assessed during a large-scale in situ costal pelagic mesocosm study, included as part of the EPOCA 2010 Arctic campaign. The mesocosm experiment included ambient conditions (fjord and nine mesocosms, with pCO2 range from ~145 to ~1420 μatm. Samples collected at nine time points (t-1, t1, t5, t7, t12, t14, t22, t26 to t28 in seven treatments (ambient fjord (~145, 2×~185, ~270, ~685, ~820, ~1050 μatm were analysed for "free-living" and "particle associated" microbial community composition using 16S rRNA amplicon sequencing. This high-throughput sequencing analysis produced ~20 000 000 16S rRNA V4 reads, which comprised 7000 OTUs. The main variables structuring these communities were, sample origin (fjord or mesocosms and the filter size fraction (free-living or particle associated. The community was significantly different between the fjord and both the control and elevated 2 mesocosms (which were not significant different after nutrients were added to the mesocosms; suggesting that the addition of nutrients is the primary driver of the change in mesocosm community structure. The relative importance of each structuring variable depended greatly on the time at which the community was sampled in relation to the phytoplankton bloom. The size fraction was the second most important factor for community structure; separating free-living from particle-associated bacteria. When free-living and particle-associated bacteria were analysed separately at different time points, the only taxon pCO2 was found to significantly affect were the Gammaproteobacteria after nutrient addition. Finally, pCO2 treatment was found to be significantly correlated (non-linear with 15 rare taxa, most of which increased in abundance with higher CO2.

  10. Nano-porous ultra-high specific surface ultrafine fibers

    Institute of Scientific and Technical Information of China (English)

    LI Xinsong; NIE Guangyu

    2004-01-01

    Nano-porous ultra-high specific surface ultrafine fibers are created by the method of "electrospinning-phase separation-leaching" (EPL) for the first time. First of all, polymer solutions of polyacrylonitrile (PAN) and polyvinylpyrrolidone (PVP) blends dissolved in co-solvent are electrospun to make ultrafine fibers when charged to high voltages. The incompatibility of PAN and PVP induces phase separation to form microdomains of PVP in the polymer blend ultrafine fibers. Then, PVP microdomains in the blend fibers are leached out in water, and porous PAN ultrafine fibers are obtained. Lastly, the surface and cross-section of the porous ultrafine fibers are observed in detail by field emission scanning electron microscope (FESEM), and the specific surface of the ultrafine fibers is measured by means of nitrogen absorption. With increasing the content of PVP, the specific surface area of the ultrafine fibers increases apparently. The specific surface area of the porous ultrafine fibers with the diameter of 2130 nm is more than 70 m2·g-1. The cross-section of the PAN porous ultrafine fibers after leaching of PVP microdomains from polymer blend fibers with the feed ratio of PAN/PVP of 10/20 shows the characteristic of porous structure with pore diameter of ca 30 nm according to FESEM photo.

  11. Nanoporous ultra-high specific surface inorganic fibres

    Science.gov (United States)

    Kanehata, Masaki; Ding, Bin; Shiratori, Seimei

    2007-08-01

    Nanoporous inorganic (silica) nanofibres with ultra-high specific surface have been fabricated by electrospinning the blend solutions of poly(vinyl alcohol) (PVA) and colloidal silica nanoparticles, followed by selective removal of the PVA component. The configurations of the composite and inorganic nanofibres were investigated by changing the average silica particle diameters and the concentrations of colloidal silica particles in polymer solutions. After the removal of PVA by calcination, the fibre shape of pure silica particle assembly was maintained. The nanoporous silica fibres were assembled as a porous membrane with a high surface roughness. From the results of Brunauer-Emmett-Teller (BET) measurements, the BET surface area of inorganic silica nanofibrous membranes was increased with the decrease of the particle diameters. The membrane composed of silica particles with diameters of 15 nm showed the largest BET surface area of 270.3 m2 g-1 and total pore volume of 0.66 cm3 g-1. The physical absorption of methylene blue dye molecules by nanoporous silica membranes was examined using UV-vis spectrometry. Additionally, the porous silica membranes modified with fluoroalkylsilane showed super-hydrophobicity due to their porous structures.

  12. Nanoporous ultra-high specific surface inorganic fibres

    Energy Technology Data Exchange (ETDEWEB)

    Kanehata, Masaki [Faculty of Science and Technology, Keio University, Yokohama 223-8522 (Japan); Ding Bin [Fiber and Polymer Science, University of California, Davis, CA 95616 (United States); Shiratori, Seimei [Faculty of Science and Technology, Keio University, Yokohama 223-8522 (Japan)

    2007-08-08

    Nanoporous inorganic (silica) nanofibres with ultra-high specific surface have been fabricated by electrospinning the blend solutions of poly(vinyl alcohol) (PVA) and colloidal silica nanoparticles, followed by selective removal of the PVA component. The configurations of the composite and inorganic nanofibres were investigated by changing the average silica particle diameters and the concentrations of colloidal silica particles in polymer solutions. After the removal of PVA by calcination, the fibre shape of pure silica particle assembly was maintained. The nanoporous silica fibres were assembled as a porous membrane with a high surface roughness. From the results of Brunauer-Emmett-Teller (BET) measurements, the BET surface area of inorganic silica nanofibrous membranes was increased with the decrease of the particle diameters. The membrane composed of silica particles with diameters of 15 nm showed the largest BET surface area of 270.3 m{sup 2} g{sup -1} and total pore volume of 0.66 cm{sup 3} g{sup -1}. The physical absorption of methylene blue dye molecules by nanoporous silica membranes was examined using UV-vis spectrometry. Additionally, the porous silica membranes modified with fluoroalkylsilane showed super-hydrophobicity due to their porous structures.

  13. High-grade surface osteosarcoma of the hand

    Energy Technology Data Exchange (ETDEWEB)

    Abe, Kuniko; Hayashi, Tomayoshi; Kinoshita, Naoe [Nagasaki University Hospital, Department of Pathology, Nagasaki (Japan); Kumagai, Kenji; Shindo, Hiroyuki [Nagasaki University Graduate School of Biomedical Sciences, Department of Orthopedic Surgery, Nagasaki (Japan); Uetani, Masataka [Nagasaki University Graduate School of Biomedical Sciences, Department of Radiology and Radiation Biology, Nagasaki (Japan); Ishida, Tsuyoshi [National Center of Neurology and Psychiatry, Department of Pathology and Laboratory Medicine, Kohnodai Hospital, Chiba (Japan); Tokyo Medical and Dental University, Department of Molecular Bone and Cartilage Pathology, Hard Tissue Genome Research Center, Tokyo (Japan)

    2007-09-15

    A 32-year-old woman presented with a 1-year history of mild pain in the right ring finger. Radiographs and CT revealed a calcified lesion with cortical erosion on the surface of the proximal aspect of the right ring finger proximal phalanx. On magnetic resonance imaging (MRI), the lesion showed low signal intensity on T1- and T2-weighted images and slight enhancement with gadolinium. Clinically, it was diagnosed as a benign bone-forming lesion such as florid reactive periostitis, and excision was accordingly performed. However, histological examination revealed proliferation of atypical osteoblastic cells among irregularly arranged osteoid seams. Taking the imaging findings into account, a pathological diagnosis of high-grade surface osteosarcoma was established. In general, bone- and cartilage-forming lesions of the hands and feet are benign. Osteosarcoma of short tubular bones in the hands and feet is extremely rare; moreover, high-grade surface osteosarcoma is one of the rarest subtypes of osteosarcoma. Nonetheless, high-grade surface osteosarcoma should be included in the differential diagnosis, particularly if the radiological findings or clinical course are not entirely typical of a more common benign process, to avoid incorrect clinicoradiological and pathological diagnosis. (orig.)

  14. High Resolution Surface Science at Mars

    Science.gov (United States)

    Bailey, Zachary J.; Tamppari, Leslie K.; Lock, Robert E.; Sturm, Erick J.

    2013-01-01

    The proposed mission would place a 2.4 m telescope in orbit around Mars with two focal plane instruments to obtain the highest resolution images and spectral maps of the surface to date (3-10x better than current). This investigation would make major contributions to all of the Mars Program Goals: life, climate, geology and preparation for human presence.

  15. Formation of high-carbon abrasion-resistant surface layers when high-energy heating by high-frequency currents

    Science.gov (United States)

    Plotnikova, N. V.; Skeeba, V. Yu; Martyushev, N. V.; Miller, R. A.; Rubtsova, N. S.

    2016-11-01

    The paper shows the possibility of carburization of low-carbon steel surface layers using high-frequency currents. The mathematical modeling of carburization using high-energy heating by high-frequency currents (HEH HFC) has been carried out, the temperature fields formed during the given processing have been calculated, as well as the structural changes in the surface layers have been simulated. The features of the structure formation in the surface layers of low-carbon steel after carburizing via HEH HFC have been determined by optical and scanning microscopy, which is confirmed by the computational models. The rational mode of fusion via HEH HFC has also been determined (power density of the source qs = (1.5 ... 4.0) • 108 W m-2, (the relative travel speed of parts Vp = 5 ... 100 mm / sec), with forming the compressive retained stresses in the surface layer (σRS ≈ -300 ... -400 MPa).

  16. A CD44high/EGFRlow subpopulation within head and neck cancer cell lines shows an epithelial-mesenchymal transition phenotype and resistance to treatment.

    Directory of Open Access Journals (Sweden)

    Linnea La Fleur

    Full Text Available Mortality in head and neck squamous cell carcinoma (HNSCC is high due to emergence of therapy resistance which results in local and regional recurrences that may have their origin in resistant cancer stem cells (CSCs or cells with an epithelial-mesenchymal transition (EMT phenotype. In the present study, we investigate the possibility of using the cell surface expression of CD44 and epidermal growth factor receptor (EGFR, both of which have been used as stem cell markers, to identify subpopulations within HNSCC cell lines that differ with respect to phenotype and treatment sensitivity. Three subpopulations, consisting of CD44(high/EGFR(low, CD44(high/EGFR(high and CD44(low cells, respectively, were collected by fluorescence-activated cell sorting. The CD44(high/EGFR(low population showed a spindle-shaped EMT-like morphology, while the CD44(low population was dominated by cobblestone-shaped cells. The CD44(high/EGFR(low population was enriched with cells in G0/G1 and showed a relatively low proliferation rate and a high plating efficiency. Using a real time PCR array, 27 genes, of which 14 were related to an EMT phenotype and two with stemness, were found to be differentially expressed in CD44(high/EGFR(low cells in comparison to CD44(low cells. Moreover, CD44(high/EGFR(low cells showed a low sensitivity to radiation, cisplatin, cetuximab and gefitinib, and a high sensitivity to dasatinib relative to its CD44(high/EGFR(high and CD44(low counterparts. In conclusion, our results show that the combination of CD44 (high and EGFR (low cell surface expression can be used to identify a treatment resistant subpopulation with an EMT phenotype in HNSCC cell lines.

  17. High-Emissivity Coatings For High-Temperature Surfaces

    Science.gov (United States)

    Deininger, William D.; King, David Q.

    1988-01-01

    Plasma-sprayed coatings increase cooling by thermal radiation. Coating of zirconium diboride on tungsten or molybdenum increases emissivity of surface to more than 0.6 at 2,000 degree C. Applied by plasma-arc spraying after surface cleaned and roughened to ensure adhesion.

  18. INVESTIGATION OF SURFACE TEMPERATURE IN HIGH-EFFICIENCY DEEP GRINDING

    Institute of Scientific and Technical Information of China (English)

    Zhao Henghua; Cai Guangqi; Jin Tan

    2005-01-01

    A new thermal model with triangular heat flux distribution is given in high-efficiency deep grinding. The mathematical expressions are driven to calculate the surface temperature. The transient behavior of the maximum temperature on contact area is investigated in different grinding conditions with a J-type thermocouple. The maximum contact temperatures measured in different conditions are found to be between 1 000 ℃ and 1 500 ℃ in burn-out conditions. The experiment results show good agreement with the new thermal model.

  19. Investigation of surface properties of high temperature nitrided titanium alloys

    Directory of Open Access Journals (Sweden)

    E. Koyuncu

    2009-12-01

    Full Text Available Purpose: The purpose of paper is to investigate surface properties of high temperature nitrided titanium alloys.Design/methodology/approach: In this study, surface modification of Ti6Al4V titanium alloy was made at various temperatures by plasma nitriding process. Plasma nitriding treatment was performed in 80% N2-20% H2 gas mixture, for treatment times of 2-15 h at the temperatures of 700-1000°C. Surface properties of plasma nitrided Ti6Al4V alloy were examined by metallographic inspection, X-Ray diffraction and Vickers hardness.Findings: Two layers were determined by optic inspection on the samples that were called the compound and diffusion layers. Compound layer contain TiN and Ti2N nitrides, XRD results support in this formations. Maximum hardness was obtained at 10h treatment time and 1000°C treatment temperature. Micro hardness tests showed that hardness properties of the nitrided samples depend on treatment time and temperature.Practical implications: Titanium and its alloys have very attractive properties for many industries. But using of titanium and its alloys is of very low in mechanical engineering applications because of poor tribological properties.Originality/value: The nitriding of titanium alloy surfaces using plasma processes has already reached the industrial application stage in the biomedical field.

  20. Surface Pyrolysis of High Energy Materials

    Directory of Open Access Journals (Sweden)

    Luigi Deluca

    1998-10-01

    Full Text Available The Arrhenius zero-order phenomenological pyrolysis law, commonly used in conjunction with the Vieille ballistic law to study pressure-driven burning of energetic materials, is revisited. Motivated by experimental and theoretical work performed in 1984 in this Laboratory , a relationship among several interplaying parameters is found under steady-state conditions. This relationship corresponds to the Jacobian of the pyrolysis sensitivity parameters used in the Zeldovich-Novozhilov approach. The Arrhenius pyrolysis is still expressed in terms of a global surface activation energy, but consistency with the experimental ballistic law may require an explicit pressure dependence as well. This conclusion is supported by a variety of arguments drawn from different areas. The linear dependence of the pre-exponential factor on surface activation energy (known as kinetic compensation is proved and extended to the pressure exponent, for any given experimental data set under steady burning. Experimental results are reported for about a dozen solid propellants of different nature. The effects of surface pyrolysis explicit pressure dependence, although modest on steady-state burning, are potentially far-reaching for unsteady regime and/or unstable burning. The paper is mainly focussed on pressure-driven burning and Arrhenius pyrolysis, but the implemented method is believed to apply in general. Thus, enforcing KTSS zero-order phenomenological pyrolysis with the Vieille ballistic law yields similar results and requires an explicit pressure dependence. In case, the Zeldovich ballistic law is enforced instead of the classical Vieille law, no explicit pressure dependence is required. The unifying concept for these different trends is the pyrolysis Jacobian as a consistency requirement between the implemented steady pyrolysis and ballistic laws."

  1. Highly stable superhydrophobic surfaces under flow conditions

    Science.gov (United States)

    Lee, Moonchan; Yim, Changyong; Jeon, Sangmin

    2015-01-01

    We synthesized hydrophobic anodic aluminum oxide nanostructures with pore diameters of 35, 50, 65, and 80 nm directly on quartz crystal microresonators, and the stability of the resulting superhydrophobicity was investigated under flow conditions by measuring changes in the resonance frequency and dissipation factor. When the quartz substrates were immersed in water, their hydrophobic surfaces did not wet due to the presence of an air interlayer. The air interlayer was gradually replaced by water over time, which caused decreases in the resonance frequency (i.e., increases in mass) and increases in the dissipation factor (i.e., increases in viscous damping). Although the water contact angles of the nanostructures increased with increasing pore size, the stability of their superhydrophobicity increased with decreasing pore size under both static conditions (without flow) and dynamic conditions (with flow); this increase can be attributed to an increase in the solid surface area that interacts with the air layer above the nanopores as the pore size decreases. Further, the effects of increasing the flow rate on the stability of the superhydrophobicity were quantitatively determined.

  2. On the Bandwidth of High-Impedance Frequency Selective Surfaces

    CERN Document Server

    Costa, Filippo; Monorchio, Agostino; 10.1109/LAWP.2009.2038346

    2010-01-01

    In this letter, the bandwidth of high-impedance surfaces (HISs) is discussed by an equivalent circuit approach. Even if these surfaces have been employed for almost 10 years, it is sometimes unclear how to choose the shape of the frequency selective surface (FSS) on the top of the grounded slab in order to achieve the largest possible bandwidth. Here, we will show that the conventional approach describing the HIS as a parallel connection between the inductance given by the grounded dielectric substrate and the capacitance of the FSS may induce inaccurate results in the determination of the operating bandwidth of the structure. Indeed, in order to derive a more complete model and to provide a more accurate estimate of the operating bandwidth, it is also necessary to introduce the series inductance of the FSS.We will present the explicit expression for defining the bandwidth of a HIS, and we will show that the reduction of the FSS inductance results in the best choice for achieving wide operating bandwidth in c...

  3. High quality broadband spatial reflections of slow Rayleigh surface acoustic waves modulated by a graded grooved surface

    KAUST Repository

    Xu, Yanlong

    2015-01-21

    We report high quality broadband spatial reflections of Rayleigh surface acoustic waves (SAWs) through a graded grooved surface. High quality means that no wave is allowed to transmit and the incident wave is nearly all reflected to the input side. The graded grooved surface is structured by drilling one dimensional array of graded grooves with increased depths on a flat surface. We investigate SAW dispersion relations, wave field distribution at several typical SAW wavelengths, and time evolution of a Gaussian pulse through the graded grooved surface. Results show that the input broadband Rayleigh SAWs can be slowed, spatially enhanced and stopped, and finally reflected to the input side. The study suggests that engraving the flat surface can be used as an efficient and economical way to manipulate Rayleigh SAWs, which has potential application in novel SAW devices such as filters, reflectors, sensors, energy harvesters, and diodes.

  4. Broadband circularly polarizing dichroism with high efficient plasmonic helical surface.

    Science.gov (United States)

    Hu, Jingpei; Zhao, Xiaonan; Li, Ruibin; Zhu, Aijiao; Chen, Linghua; Lin, Yu; Cao, Bing; Zhu, Xiaojun; Wang, Chinhua

    2016-05-16

    We propose and experimentally demonstrate a broadband and high efficient circularly polarizing dichroism using a simple single-cycle and single-helical plasmonic surface array arranged in square lattice. Two types of helical surface structures (partially or completely covered with a gold film) are investigated. It is shown that the circular polarization dichroism in the mid-IR range (3µm - 5µm) can reach 80% (when the surface is partially covered with gold) or 65% (when the surface is completely covered with gold) with a single-cycle and single-helical surface. Experimental fabrications of the proposed helical plasmonic surface are implemented with direct 3D laser writing followed by electron beam evaporation deposition of gold. The experimental evaluations of the circular polarization dichroism are in excellent agreement with the simulation. The proposed helical surface structure is of advantages of easy-fabrication, high-dichroism and scalable to other frequencies as a high efficient broadband circular polarizer.

  5. Highly charged ions interacting with carbon surfaces : An influence of surface structure?

    NARCIS (Netherlands)

    Morgenstern, R; Winters, D; Schlatholter, T; Hoekstra, R

    Auger electron spectroscopy has been used to investigate the reaction of various carbon surfaces - including fullerene covered metal surfaces - on the impact of highly charged ions. An influence of the electronic surface structure on the interaction is clearly observed. However, the goal of

  6. Antibody recognition force microscopy shows that outer membrane cytochromes OmcA and MtrC are expressed on the exterior surface of Shewanella oneidensis MR-1.

    Science.gov (United States)

    Lower, Brian H; Yongsunthon, Ruchirej; Shi, Liang; Wildling, Linda; Gruber, Hermann J; Wigginton, Nicholas S; Reardon, Catherine L; Pinchuk, Grigoriy E; Droubay, Timothy C; Boily, Jean-François; Lower, Steven K

    2009-05-01

    Antibody recognition force microscopy showed that OmcA and MtrC are expressed on the exterior surface of living Shewanella oneidensis MR-1 cells when Fe(III), including solid-phase hematite (Fe(2)O(3)), was the terminal electron acceptor. OmcA was localized to the interface between the cell and mineral. MtrC displayed a more uniform distribution across the cell surface. Both cytochromes were associated with an extracellular polymeric substance.

  7. The cataract-associated V41M mutant of human γS-crystallin shows specific structural changes that directly enhance local surface hydrophobicity

    Energy Technology Data Exchange (ETDEWEB)

    Bharat, Somireddy Venkata; Shekhtman, Alexander; Pande, Jayanti, E-mail: jpande@albany.edu

    2014-01-03

    Highlights: •We present NMR analysis of V41M, a cataract-causing mutant of human γS-crystallin. •Mutation alters strand–strand interactions throughout the N-terminal domain. •Mutation directly affects Trp46 due to key Met41-S–Trp46-pi interactions. •We identify the basis of the surface hydrophobicity increase and residues involved. -- Abstract: The major crystallins expressed in the human lens are γS-, γC- and γD-crystallins. Several mutations in γS-crystallin are associated with hereditary cataracts, one of which involves the substitution of a highly conserved Valine at position 41 to Methionine. According to a recent report, the mutant protein, V41M, shows lower stability and increased surface hydrophobicity compared to the wild-type, and a propensity for self-aggregation. Here we address the structural differences between the two proteins, with residue-level specificity using NMR spectroscopy. Based on the structural model of the mutant protein, our results clearly show that the mutation creates a major local perturbation almost at the junction of the first and second “Greek-key” motifs in the N-terminal domain. A larger section of the second motif (residues 44–86) appears to be mainly affected. Based on the sizeable chemical shift of the imino proton of the indole side-chain of Trp46 in V41M, we suggest that the sulphur atom of Met41 is involved in an S–π interaction with Trp46. This interaction would bring the last β-strand of the first “Greek-key” motif closer to the first β-strand of the second motif. This appears to lead to a domino effect, towards both the N- and C-terminal ends, even as it decays off substantially beyond the domain interface. During this process discreet hydrophobic surface patches are created, as revealed by ANS-binding. Such changes would not affect the secondary structure or cause a major change in the tertiary structure, but can lead to self-aggregation or aberrant binding interactions of the mutant

  8. High Efficiency Acetylcholinesterase Immobilization on DNA Aptamer Modified Surfaces

    Directory of Open Access Journals (Sweden)

    Orada Chumphukam

    2014-04-01

    Full Text Available We report here the in vitro selection of DNA aptamers for electric eel acetylcholinesterase (AChE. One selected aptamer sequence (R15/19 has a high affinity towards the enzyme (Kd = 157 ± 42 pM. Characterization of the aptamer showed its binding is not affected by low ionic strength (~20 mM, however significant reduction in affinity occurred at high ionic strength (~1.2 M. In addition, this aptamer does not inhibit the catalytic activity of AChE that we exploit through immobilization of the DNA on a streptavidin-coated surface. Subsequent immobilization of AChE by the aptamer results in a 4-fold higher catalytic activity when compared to adsorption directly on to plastic.

  9. Targeted Reminder Phone Calls to Patients at High Risk of No-Show for Primary Care Appointment: A Randomized Trial.

    Science.gov (United States)

    Shah, Sachin J; Cronin, Patrick; Hong, Clemens S; Hwang, Andrew S; Ashburner, Jeffrey M; Bearnot, Benjamin I; Richardson, Calvin A; Fosburgh, Blair W; Kimball, Alexandra B

    2016-12-01

    No-shows, or missed appointments, are a problem for many medical practices. They result in fragmented care and reduce access for all patients. To determine whether telephone reminder calls targeted to patients at high risk of no-show can reduce no-show rates. Single-center randomized controlled trial. A total of 2247 primary care patients in a hospital-based primary care clinic at high risk of no-show (>15 % risk) for their appointment in 7 days. Seven days prior to their appointment, intervention arm patients were placed in a calling queue to receive a reminder phone call from a patient service coordinator. Coordinators were trained to engage patients in concrete planning. All patients received an automated phone call (usual care). Primary outcome was no-show rate. Secondary outcomes included arrival rate, cancellation rate, reschedule rate, time to cancellation, and change in revenue. The no-show rate in the intervention arm (22.8 %) was significantly lower (absolute risk difference -6.4 %, p < 0.01, 95 % CI [-9.8 to -3.0 %]) than that in the control arm (29.2 %). Arrival, cancellation, and reschedule rates did not differ significantly. In the intervention arm, rescheduling and cancellations occurred further in advance of the appointment (mean difference, 0.35 days; 95 % CI [0.07-0.64]; p = 0.01). Reimbursement did not differ significantly. A phone call 7 days prior to an appointment led to a significant reduction in no-shows and increased reimbursement among patients at high risk of no-show. The use of targeted interventions may be of interest to practices taking on increased accountability for population health.

  10. Molecular Surface Chemistry by Metal Single Crystals and Nanoparticles from Vacuum to High Pressure.

    Energy Technology Data Exchange (ETDEWEB)

    Somorjai, Gabor A.; Park, Jeong Y.

    2008-04-05

    Model systems for studying molecular surface chemistry have evolved from single crystal surfaces at low pressure to colloidal nanoparticles at high pressure. Low pressure surface structure studies of platinum single crystals using molecular beam surface scattering and low energy electron diffraction techniques probe the unique activity of defects, steps and kinks at the surface for dissociation reactions (H-H, C-H, C-C, O{double_bond}O bonds). High-pressure investigations of platinum single crystals using sum frequency generation vibrational spectroscopy have revealed the presence and the nature of reaction intermediates. High pressure scanning tunneling microscopy of platinum single crystal surfaces showed adsorbate mobility during a catalytic reaction. Nanoparticle systems are used to determine the role of metal-oxide interfaces, site blocking and the role of surface structures in reactive surface chemistry. The size, shape and composition of nanoparticles play important roles in determining reaction activity and selectivity.

  11. High Resolution CryoFESEM of Microbial Surfaces

    Science.gov (United States)

    Erlandsen, Stanley; Lei, Ming; Martin-Lacave, Ines; Dunny, Gary; Wells, Carol

    2003-08-01

    The outer surfaces of three microorganisms, Giardia lamblia, Enterococcus faecalis, and Proteus mirabilis, were investigated by cryo-immobilization followed by sublimation of extracellular ice and cryocoating with either Pt alone or Pt plus carbon. Cryocoated samples were examined at [minus sign]125°C in either an in-lens field emission SEM or a below-the-lens field emission SEM. Cryocoating with Pt alone was sufficient for low magnification observation, but attempts to do high-resolution imaging resulted in radiolysis and cracking of the specimen surface. Double coating with Pt and carbon, in combination with high resolution backscatter electron detectors, enabled high-resolution imaging of the glycocalyx of bacteria, revealing a sponge-like network over the surface. High resolution examination of bacterial flagella also revealed a periodic substructure. Common artifacts included radiolysis leading to “cracking” of the surface, and insufficient deposition of Pt resulting in the absence of detectable surface topography.

  12. Variation of Surface Charge along the Surface of Wool Fibers Assessed by High-Resolution Force Spectroscopy

    Science.gov (United States)

    Zimmerman, Bonnie; Chow, James; Abbott, Albert G.; Ellison, Michael S.; Kennedy, Marian S.; Dean, Delphine

    2011-01-01

    In this study, we have mapped the surface charge of wool fibers using chemically specific high-resolution force spectroscopy in order to better understand the dispersion of amino acids in relation to fiber morphology. The inter-surface forces between standard atomic force microscopy (AFM) probe tips (tip radius ~ 50 nm) functionalized with COOH and NH3 terminated alkanethiol self assembling monolayers and the wool surface were used to estimate the surface charge per unit area using linear Poisson-Boltzmann-based electrostatic double layer theory. The positional measurement of nano-scale surface charge showed a correlation between the surface charge and fiber morphology, indicated that basic amino acids are located near the scale edges. PMID:21866220

  13. Possible high absorptance and low emittance selective surface for high temperature solar thermal collectors.

    Science.gov (United States)

    Zhang, Q C; Kelly, J C; Mills, D R

    1991-05-01

    Optical reflectivity measurements show that the reflectivity of Ge is dramatically reduced in the wavelength 0.3-1.4-microm range after high dose oxygen ion implantation. To explain such greatly reduced reflectivity, a model has been developed for the reflectivity of high dose oxygen implanted germanium. Our experimentally measured and calculated reflectivities show that, for a layered structure consisting of a Ge and GeO(2) mixture on Ge on GeO(2) on a Cu substrate, a low reflectivity of 0-10% in the solar spectrum is obtained, together with a high reflectivity approximately 100% in the 1.7-25-microm wavelength range. This is close to that of an ideal selective surface for solar energy thermal collectors operating at high temperatures from 300 to 500 degrees C.

  14. High resolution imaging of surface patterns of single bacterial cells

    Energy Technology Data Exchange (ETDEWEB)

    Greif, Dominik; Wesner, Daniel [Experimental Biophysics and Applied Nanoscience, Bielefeld University, Universitaetsstrasse 25, 33615 Bielefeld (Germany); Regtmeier, Jan, E-mail: jan.regtmeier@physik.uni-bielefeld.de [Experimental Biophysics and Applied Nanoscience, Bielefeld University, Universitaetsstrasse 25, 33615 Bielefeld (Germany); Anselmetti, Dario [Experimental Biophysics and Applied Nanoscience, Bielefeld University, Universitaetsstrasse 25, 33615 Bielefeld (Germany)

    2010-09-15

    We systematically studied the origin of surface patterns observed on single Sinorhizobium meliloti bacterial cells by comparing the complementary techniques atomic force microscopy (AFM) and scanning electron microscopy (SEM). Conditions ranged from living bacteria in liquid to fixed bacteria in high vacuum. Stepwise, we applied different sample modifications (fixation, drying, metal coating, etc.) and characterized the observed surface patterns. A detailed analysis revealed that the surface structure with wrinkled protrusions in SEM images were not generated de novo but most likely evolved from similar and naturally present structures on the surface of living bacteria. The influence of osmotic stress to the surface structure of living cells was evaluated and also the contribution of exopolysaccharide and lipopolysaccharide (LPS) by imaging two mutant strains of the bacterium under native conditions. AFM images of living bacteria in culture medium exhibited surface structures of the size of single proteins emphasizing the usefulness of AFM for high resolution cell imaging.

  15. Highly Stable Silver Nanoplates for Surface Plasmon Resonance Biosensing

    Energy Technology Data Exchange (ETDEWEB)

    Gao, Chuanbo [University of California, Riverside; Lu, Zhenda [University of California, Riverside; Chi, Miaofang [ORNL; Liu, ying [University of California, Riverside; Cheng, Quan [University of California, Riverside; Yin, Yadong [University of California, Riverside

    2012-01-01

    An SPR biosensor was developed by employing highly stable Au-protected Ag nanoplates (NP) as enhancers (see picture). Superior performance was achieved by depositing a thin and uniform coating of Au on the Ag surface while minimizing disruptive galvanic replacement and retaining the strong surface plasmon resonance (SPR) of the silver nanoplates.

  16. Combined (18)F-Fluciclovine PET/MRI shows potential for detection and characterization of high-risk prostate cancer.

    Science.gov (United States)

    Elschot, Mattijs; Selnæs, Kirsten M; Sandsmark, Elise; Krüger-Stokke, Brage; Størkersen, Øystein; Giskeødegård, Guro F; Tessem, May-Britt; Moestue, Siver A; Bertilsson, Helena; Bathen, Tone F

    2017-10-06

    The objective of this study is to investigate if quantitative imaging features derived from combined (18)F-Fluciclovine Positron Emission Tomograpy (PET) / multiparametric Magnetic Resonance Imaging (MRI) show potential for detection and characterization of primary prostate cancer. Methods: Twenty-eight (28) patients diagnosed with high-risk prostate cancer underwent simultaneous (18)F-Fluciclovine PET/MRI before radical prostatectomy. Volumes-of-interest (VOIs) of prostate tumors, benign prostatic hyperplasia (BPH) nodules, prostatitis, and healthy tissue were delineated on T2-weighted images using histology as a reference. Tumor VOIs were marked as high-grade (≥ Gleason Grade group 3) or not. MRI and PET features were extracted on the voxel and VOI-level. Partial least-squared discriminant analysis (PLS-DA) with double leave-one-patient-out cross validation was performed to classify tumor from benign tissue (BPH, prostatitis, healthy tissue) and high-grade tumor from other tissue (low-grade tumor, benign tissue). The performances of PET, MRI, and combined PET/MRI features were compared using the area under the receiver operating characteristic curve (AUC). Results: Voxel and VOI features were extracted from 40 tumor (26 high-grade), 36 BPH, 6 prostatitis, and 37 healthy tissue VOIs. PET/MRI performed better than MRI and PET for classification of tumor vs benign tissue (voxel: AUC 87%, 81%, and 83%; VOI: AUC 96%, 93%, and 93%, respectively) and high-grade tumor vs other tissue (voxel: AUC 85%, 79%, and 81%; VOI: AUC 93%, 93%, and 91%, respectively). T2-weighted MRI, diffusion-weighted MRI and PET features were most important for classification. Conclusion: Combined (18)F-Fluciclovine PET/multiparametric MRI shows potential for improving detection and characterization of high-risk prostate cancer, in comparison to MRI and PET alone. Copyright © 2017 by the Society of Nuclear Medicine and Molecular Imaging, Inc.

  17. Show Time

    Institute of Scientific and Technical Information of China (English)

    2004-01-01

    <正> Story: Show Time!The whole class presents the story"Under the Sea".Everyone is so excited and happy.Both Leo and Kathy show their parentsthe characters of the play."Who’s he?"asks Kathy’s mom."He’s the prince."Kathy replies."Who’s she?"asks Leo’s dad."She’s the queen."Leo replieswith a smile.

  18. Snobbish Show

    Institute of Scientific and Technical Information of China (English)

    YIN PUMIN

    2010-01-01

    @@ The State Administration of Radio,Film and Television (SARFT),China's media watchdog,issued a new set of mles on June 9 that strictly regulate TV match-making shows,which have been sweeping the country's primetime programming. "Improper social and love values such as money worship should not be presented in these shows.Humiliation,verbal attacks and sex-implied vulgar content are not allowed" the new roles said.

  19. Highly smooth Nb surfaces fabricated by buffered electropolishing

    Energy Technology Data Exchange (ETDEWEB)

    Andy T. Wu; John Mammossor; H. Phillips; Jean Delayen; Charles Reece; Amy Wilkerson; David Smith; Robert Ike

    2005-05-01

    It is demonstrated that highly smooth Nb surfaces can be obtained through Buffered ElectroPolishing (BEP) employing an electrolyte consisting of lactic, sulfuric, and hydrofluoric acids. Parameters that control the polishing process are optimized to achieve the smoothest surface finish with the help of surface observations using a scanning electron microscope and a Metallographic Optical Microscope (MOM). The polishing rate of BEP is determined to be 0.646 {micro}m/min that is much higher than 0.381 {micro}m/min achieved by the conventional ElectroPolishing (EP) process widely used in the Superconducting Radio Frequency (SRF) community. A high precision and large scan area 3-D profilometer is used to view morphology of the treated Nb surfaces. Statistical data, such as, rms, total indicator runout, and arithmetic mean deviation of the Nb surfaces are extracted from the profilometer images. It is found that Nb surfaces treated by BEP are an order of magnitude smoother than those treated by the optimized EP process. The chemical composition of the Nb surfaces after BEP is analyzed by static and dynamic Secondary Ion Mass Spectrometer (SIMS) systems. Cracking patterns of the Nb surfaces under different primary ion sources of Ga{sup +}, Au{sup +}, and Ar{sup +} are reported. The depth profile of the surface niobium oxides is studied through continuously monitoring niobium and its relevant oxides' peaks as a function of time. Dynamic SIMS results imply that the surface oxide structure of Nb may be more complicated than what usually believed and can be inhomogeneous. Preliminary results of BEP on Nb SRF single cell cavities and half-cells are reported. It is shown that smooth and bright surfaces can be obtained in 30 minutes when the electric field inside a SRF cavity is uniform during a BEP process. This study reveals that BEP is a highly promising technique for surface treatment on Nb SRF cavities to be used in particle accelerators.

  20. Molecular Dynamics Simulations of Surface Processes: Oxygen Recombination on Silica Surfaces at High Temperature

    Science.gov (United States)

    2007-07-01

    size-scalable cluster approach with SixOy clusters of increasing size cleaved from the β- cristobalite unit cell. In this study the hybrid Hartree...values of the β- cristobalite cell and extending the Molecular Dynamics Simulations of Surface Processes: Oxygen Recombination on Silica Surfaces at... cristobalite surface is reported as a function of the distance of the N atom from the Si active atom. The dashed line shows the interaction

  1. NOAA High-Resolution Sea Surface Temperature (SST) Analysis Products

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This archive covers two high resolution sea surface temperature (SST) analysis products developed using an optimum interpolation (OI) technique. The analyses have a...

  2. Viral reverse transcriptases show selective high affinity binding to DNA-DNA primer-templates that resemble the polypurine tract.

    Directory of Open Access Journals (Sweden)

    Gauri R Nair

    Full Text Available Previous results using a SELEX (Systematic Evolution of Ligands by Exponential Enrichment-based approach that selected DNA primer-template duplexes binding with high affinity to HIV reverse transcriptase (RT showed that primers mimicking the 3' end, and in particular the six nt terminal G tract, of the RNA polypurine tract (PPT; HIV PPT: 5'-AAAAGAAAAGGGGGG-3' were preferentially selected. In this report, two viral (Moloney murine leukemia virus (MuLV and avian myeloblastosis virus (AMV and one retrotransposon (Ty3 RTs were used for selection. Like HIV RT, both viral RTs selected duplexes with primer strands mimicking the G tract at the PPT 3' end (AMV PPT: 5'-AGGGAGGGGGA-3'; MuLV PPT: 5'-AGAAAAAGGGGGG-3'. In contrast, Ty3, whose PPT lacks a G tract (5'-GAGAGAGAGGAA-3' showed no selective binding to any duplex sequences. Experiments were also conducted with DNA duplexes (termed DNA PPTs mimicking the RNA PPT-DNA duplex of each virus and a control duplex with a random DNA sequence. Retroviral RTs bound with high affinity to all viral DNA PPT constructs, with HIV and MuLV RTs showing comparable binding to the counterpart DNA PPT duplexes and reduced affinity to the AMV DNA PPT. AMV RT showed similar behavior with a modest preference for its own DNA PPT. Ty3 RT showed no preferential binding for its own or any other DNA PPT and viral RTs bound the Ty3 DNA PPT with relatively low affinity. In contrast, binding affinity of HIV RT to duplexes containing the HIV RNA PPT was less dependent on the G tract, which is known to be pivotal for efficient extension. We hypothesize that the G tract on the RNA PPT helps shift the binding orientation of RT to the 3' end of the PPT where extension can occur.

  3. The green alga Zygogonium ericetorum (Zygnematophyceae, Charophyta) shows high iron and aluminium tolerance: protection mechanisms and photosynthetic performance.

    Science.gov (United States)

    Herburger, Klaus; Remias, Daniel; Holzinger, Andreas

    2016-08-01

    Streptophyte green algae, ancestors of Embryophytes, occur frequently in terrestrial habitats being exposed to high light intensities, water scarcity and potentially toxic metal cations under acidic conditions. The filamentous Zygogonium ericetorum synthesizes a purple vacuolar ferrous pigment, which is lost after aplanospore formation. However, it is unknown whether this cellular reorganization also removes excessive iron from the protoplast and how Z. ericetorum copes with high concentrations of aluminium. Here we show that aplanospore formation shifts iron into the extracellular space of the algal filament. Upon germination of aplanospores, aluminium is bound in the parental cell wall. Both processes reduce iron and aluminium in unpigmented filaments. Comparison of the photosynthetic oxygen production in response to light and temperature gradients in two different Z. ericetorum strains from an Austrian alpine and a Scottish highland habitat revealed lower values in the latter strain. In contrast, the Scottish strain showed a higher optimum quantum yield of PSII during desiccation stress followed by rehydration. Furthermore, pigmented filaments of both strains exhibited a higher light and temperature dependent oxygen production when compared to the unpigmented phenotype. Our results demonstrate a high metal tolerance of Z. ericetorum, which is crucial for surviving in acidic terrestrial habitats. © FEMS 2016.

  4. Three-dimensional shape measurement of a highly reflected, specular surface with structured light method.

    Science.gov (United States)

    Zhang, Hongwei; Ji, Lishuan; Liu, Shugui; Li, Shaohui; Han, Shujian; Zhang, Xiaojie

    2012-11-01

    This paper proposes a mathematical measurement model of a highly reflected, specular surface with structured light method. In the measurement, an auxiliary fringe pattern named amplitude perturbation is adopted to be projected onto the measured surface. The amplitude perturbation can ease the procedure of searching the corresponding points between the phase map of the measured surface and that of the reference plane by locking up the most reliable point as the starting unwrapping point whose true phase can be calculated accurately. The proposed method is also suitable for measuring the step surfaces such as gauge blocks with different heights. Furthermore, the image segmentation technology is introduced in the phase unwrapping procedure to increase the speed. Based on the unwrapped phase map, zonal wave-front reconstruction algorithm is implemented to realize three-dimensional, highly reflected, specular surface reconstruction. Experimental studies show that the developed methodology displays accuracy and high stability for highly reflected, specular surface measurement.

  5. HIGH VELOCITY THERMAL GUN FOR SURFACE PREPARATION AND TREATMENT

    Directory of Open Access Journals (Sweden)

    I.A. Gorlach

    2012-01-01

    Full Text Available Many surface preparation and treatment processes utilise compressed air to propel particles against surfaces in order to clean and treat them. The effectiveness of the processes depends on the velocity of the particles, which in turn depends on the pressure of the compressed air. This paper describes a thermal gun built on the principles of High Velocity Air Fuel (HVAF and High Velocity Oxy Fuel (HVOF processes. The designed apparatus can be used for abrasive blasting, coating of surfaces, cutting of rocks, removing rubber from mining equipment, cleaning of contaminations etc.

  6. Exotic high activity surface patterns in PtAu nanoclusters

    KAUST Repository

    Mokkath, Junais Habeeb

    2013-05-09

    The structure and chemical ordering of PtAu nanoclusters of 79, 135, and 201 atoms are studied via a combination of a basin hopping atom-exchange technique (to locate the lowest energy homotops at fixed composition), a symmetry orbit technique (to find the high symmetry isomers), and density functional theory local reoptimization (for determining the most stable homotop). The interatomic interactions between Pt and Au are derived from the empirical Gupta potential. The lowest energy structures show a marked tendency toward PtcoreAushell chemical ordering by enrichment of the more cohesive Pt in the core region and of Au in the shell region. We observe a preferential segregation of Pt atoms to (111) facets and Au atoms to (100) facets of the truncated octahedron cluster motif. Exotic surface patterns are obtained particularly for Pt-rich compositions, where Pt atoms are being surrounded by Au atoms. These surface arrangements boost the catalytic activity by creating a large number of active sites. © 2013 American Chemical Society.

  7. EROBATIC SHOW

    Institute of Scientific and Technical Information of China (English)

    2016-01-01

    Visitors look at plane models of the Commercial Aircraft Corp. of China, developer of the count,s first homegrown large passenger jet C919, during the Singapore Airshow on February 16. The biennial event is the largest airshow in Asia and one of the most important aviation and defense shows worldwide. A number of Chinese companies took part in the event during which Okay Airways, the first privately owned aidine in China, signed a deal to acquire 12 Boeing 737 jets.

  8. High temperature surface degradation of III-V nitrides

    Energy Technology Data Exchange (ETDEWEB)

    Vartuli, C.B.; Pearton, S.J.; Abernathy, C.R.; MacKenzie, J.D.; Lambers, E.S. [Univ. of Florida, Gainesville, FL (United States). Dept. of Materials Science and Engineering; Zolper, J.C. [Sandia National Labs., Albuquerque, NM (United States)

    1996-05-01

    The surface stoichiometry, surface morphology and electrical conductivity of AlN, GaN, InN, InGaN and InAlN was examined at rapid thermal annealing temperatures up to 1,150 C. The sheet resistance of the AlN dropped steadily with annealing, but the surface showed signs of roughening only above 1,000 C. Auger Electronic Spectroscopy (AES) analysis showed little change in the surface stoichiometry even at 1,150 C. GaN root mean square (RMS) surface roughness showed an overall improvement with annealing, but the surface became pitted at 1,000 C, at which point the sheet resistance also dropped by several orders of magnitude, and AES confirmed a loss of N from the surface. The InN surface had roughened considerably even at 650 C, and scanning electron microscopy (SEM) showed significant degradation. In contrast to the binary nitrides the sheet resistance of InAlN was found to increase by {approximately} 10{sup 2} from the as grown value after annealing at 800 C and then remain constant up to 1,000 C, while that of InGaN increased rapidly above 700 C. The RMS roughness increased above 800 C and 700 C respectively for InAlN and InGaN samples. In droplets began to form on the surface at 900 C for InAlN and at 800 C for InGaN, and then evaporate at 1,000 C leaving pits. AES analysis showed a decrease in the N concentration in the top 500 {angstrom} of the sample for annealing {ge} 800 C in both materials.

  9. A combined cultivation and cultivation-independent approach shows high bacterial diversity in water-miscible metalworking fluids.

    Science.gov (United States)

    Lodders, Nicole; Kämpfer, Peter

    2012-06-01

    Ten metalworking fluids (MWF) and seven water preparation basis samples (WPB) were taken from five industrial plants in Germany. Total cells (TCC) and colony forming units (CFU) were counted, strains were isolated and their 16S rRNA gene was sequenced. Additionally, DNA was extracted directly from the samples, and clone libraries of 16S rRNA genes were built and gene sequenced. TCC ranged from 7.6×10(4) TCC/mL MWF to 1.6×10(8) TCC/mL MWF, and from 4.6×10(2) TCC/mL WPB to 7.8×10(7) TCC/mL WPB. The CFU showed similar but often lower results. A total of 70 isolates and 732 clones were 16S rRNA gene sequenced and all isolates, as well as 183 of the nearly full length 16S rRNA of these clones, were gene sequenced. A total of 98 different genera were detected in all 17 samples. The number of genera within each sample varied highly, with 1-22 genera per sample. The dominant genera in MWF were Leucobacter, Desemzia, Sphingomonas and Wautersiella. From these, only Sphingomonas was detected in WPB as well. This study showed that MWF can harbour a high bacterial diversity, which differs significantly from the bacterial flora of the corresponding WPB.

  10. Surfaces for high heat dissipation with no Leidenfrost limit

    Science.gov (United States)

    Sajadi, Seyed Mohammad; Irajizad, Peyman; Kashyap, Varun; Farokhnia, Nazanin; Ghasemi, Hadi

    2017-07-01

    Heat dissipation from hot surfaces through cooling droplets is limited by the Leidenfrost point (LFP), in which an insulating vapor film prevents direct contact between the cooling droplet and the hot surface. A range of approaches have been developed to raise this limit to higher temperatures, but the limit still exists. Recently, a surface architecture, decoupled hierarchical structure, was developed that allows the suppression of LFP completely. However, heat dissipation by the structure in the low superheat region was inferior to other surfaces and the structure required an extensive micro/nano fabrication procedure. Here, we present a metallic surface structure with no LFP and high heat dissipation capacity in all temperature ranges. The surface features the nucleate boiling phenomenon independent of the temperature with an approximate heat transfer coefficient of 20 kW m-2 K-1. This surface is developed in a one-step process with no micro/nano fabrication. We envision that this metallic surface provides a unique platform for high heat dissipation in power generation, photonics/electronics, and aviation systems.

  11. A Multi-Channel Method for Retrieving Surface Temperature for High-Emissivity Surfaces from Hyperspectral Thermal Infrared Images

    Directory of Open Access Journals (Sweden)

    Xinke Zhong

    2015-06-01

    Full Text Available The surface temperature (ST of high-emissivity surfaces is an important parameter in climate systems. The empirical methods for retrieving ST for high-emissivity surfaces from hyperspectral thermal infrared (HypTIR images require spectrally continuous channel data. This paper aims to develop a multi-channel method for retrieving ST for high-emissivity surfaces from space-borne HypTIR data. With an assumption of land surface emissivity (LSE of 1, ST is proposed as a function of 10 brightness temperatures measured at the top of atmosphere by a radiometer having a spectral interval of 800–1200 cm−1 and a spectral sampling frequency of 0.25 cm−1. We have analyzed the sensitivity of the proposed method to spectral sampling frequency and instrumental noise, and evaluated the proposed method using satellite data. The results indicated that the parameters in the developed function are dependent on the spectral sampling frequency and that ST of high-emissivity surfaces can be accurately retrieved by the proposed method if appropriate values are used for each spectral sampling frequency. The results also showed that the accuracy of the retrieved ST is of the order of magnitude of the instrumental noise and that the root mean square error (RMSE of the ST retrieved from satellite data is 0.43 K in comparison with the AVHRR SST product.

  12. Tree Rings Show Recent High Summer-Autumn Precipitation in Northwest Australia Is Unprecedented within the Last Two Centuries.

    Science.gov (United States)

    O'Donnell, Alison J; Cook, Edward R; Palmer, Jonathan G; Turney, Chris S M; Page, Gerald F M; Grierson, Pauline F

    2015-01-01

    An understanding of past hydroclimatic variability is critical to resolving the significance of recent recorded trends in Australian precipitation and informing climate models. Our aim was to reconstruct past hydroclimatic variability in semi-arid northwest Australia to provide a longer context within which to examine a recent period of unusually high summer-autumn precipitation. We developed a 210-year ring-width chronology from Callitris columellaris, which was highly correlated with summer-autumn (Dec-May) precipitation (r = 0.81; 1910-2011; p < 0.0001) and autumn (Mar-May) self-calibrating Palmer drought severity index (scPDSI, r = 0.73; 1910-2011; p < 0.0001) across semi-arid northwest Australia. A linear regression model was used to reconstruct precipitation and explained 66% of the variance in observed summer-autumn precipitation. Our reconstruction reveals inter-annual to multi-decadal scale variation in hydroclimate of the region during the last 210 years, typically showing periods of below average precipitation extending from one to three decades and periods of above average precipitation, which were often less than a decade. Our results demonstrate that the last two decades (1995-2012) have been unusually wet (average summer-autumn precipitation of 310 mm) compared to the previous two centuries (average summer-autumn precipitation of 229 mm), coinciding with both an anomalously high frequency and intensity of tropical cyclones in northwest Australia and the dominance of the positive phase of the Southern Annular Mode.

  13. High-temperature vesuvianite: crystal chemistry and surface considerations

    Science.gov (United States)

    Elmi, Chiara; Brigatti, Maria Franca; Pasquali, Luca; Montecchi, Monica; Laurora, Angela; Malferrari, Daniele; Nannarone, Stefano

    2011-06-01

    A multi-methodical approach has been applied for characterizing the bulk and surface crystal chemical features of a high-temperature vesuvianite crystal from skarns of Mount Somma-Vesuvius Volcano (Naples, Italy). Vesuvianite belongs to the space group P4/ nnc with unit cell parameters a = 15.633(1) Å, c = 11.834(1) Å and chemical formula (Ca18.858 Na0.028 Ba0.004 K0.006 Sr0.005 □0.098)19.000 (Al8.813 Ti0.037 Mg2.954 Mn0.008 Fe{0.114/2+} Fe{1.375/3+} Cr0.008 B0.202)13.511 Si18.000(O0.261 F0.940 OH7.799)9.000. Structure refinement, which converges at R = 0.0328, demonstrates a strong positional disorder down the fourfold axes, indicating that the Y1 site is split into two positions (Y1A and Y1B) alternatively occupied. However, because of X4 proximity to Y1B and Y1A, X4 cannot be occupied if Y1B or Y1A are. Overall Y1 occupancy (Y1A + Y1B) reaches approximately 0.5, as common in vesuvianite and occupancy of Y1B site is extremely limited. Moreover, T1 position, limitedly occupied, accommodates the excess of cations generally related to Y position. A small quantity (0.202 apfu) of boron is sited at the T2 site that, like T1, is poorly occupied. The determination of the amount of each element on the (100) vesuvianite surface, obtained through X-ray photoelectron spectroscopy high-resolution spectra in the region of the Si2p, Al2p, Mg1s, and Ca2p core levels, evidences that a greater amount of aluminum and a smaller amount of calcium characterize the surface with respect to the bulk. Although both of these features require further investigation, we may consider the Al increase can be related to preferential orientation of Al-rich sites on the (100) plane. Furthermore, the surface structure of vesuvianite suggests that Al, Ca, and Mg cations maintain coordination features at the surface similar to the bulk. Silica, however, while presenting fourfold coordination, shows also a [1]-fold small coordinated component at binding energy 99.85 eV, due to broken Si-O bonds at

  14. The intensity dependence of surface recombination in high concentration solar cells with charge induced passivation

    Science.gov (United States)

    Gray, J. L.; Schwartz, R. J.; Lundstrom, M. S.; Nasby, R. D.

    High intensity solar cells which are designed to minimize series resistance and shadowing losses, frequently employ an illuminated surface which is relatively far removed from the collecting junctions. This requires that the surface be well passivated to minimize surface recombination. One technique frequently employed to minimize surface recombination is to incorporate a fixed charge in the passivating oxide. This work shows that at sufficiently high intensities the surface recombination can increase dramatically. This results in a reduction in the high intensity collection efficiency. A comparison of the collection efficiency of interdigitated back contact cells and etched multiple vertical junction cells is given which shows that EMVJ cells are less sensitive to this effect than IBC cells.

  15. A novel halophilic lipase, LipBL, showing high efficiency in the production of eicosapentaenoic acid (EPA.

    Directory of Open Access Journals (Sweden)

    Dolores Pérez

    Full Text Available BACKGROUND: Among extremophiles, halophiles are defined as microorganisms adapted to live and thrive in diverse extreme saline environments. These extremophilic microorganisms constitute the source of a number of hydrolases with great biotechnological applications. The interest to use extremozymes from halophiles in industrial applications is their resistance to organic solvents and extreme temperatures. Marinobacter lipolyticus SM19 is a moderately halophilic bacterium, isolated previously from a saline habitat in South Spain, showing lipolytic activity. METHODS AND FINDINGS: A lipolytic enzyme from the halophilic bacterium Marinobacter lipolyticus SM19 was isolated. This enzyme, designated LipBL, was expressed in Escherichia coli. LipBL is a protein of 404 amino acids with a molecular mass of 45.3 kDa and high identity to class C β-lactamases. LipBL was purified and biochemically characterized. The temperature for its maximal activity was 80°C and the pH optimum determined at 25°C was 7.0, showing optimal activity without sodium chloride, while maintaining 20% activity in a wide range of NaCl concentrations. This enzyme exhibited high activity against short-medium length acyl chain substrates, although it also hydrolyzes olive oil and fish oil. The fish oil hydrolysis using LipBL results in an enrichment of free eicosapentaenoic acid (EPA, but not docosahexaenoic acid (DHA, relative to its levels present in fish oil. For improving the stability and to be used in industrial processes LipBL was immobilized in different supports. The immobilized derivatives CNBr-activated Sepharose were highly selective towards the release of EPA versus DHA. The enzyme is also active towards different chiral and prochiral esters. Exposure of LipBL to buffer-solvent mixtures showed that the enzyme had remarkable activity and stability in all organic solvents tested. CONCLUSIONS: In this study we isolated, purified, biochemically characterized and immobilized a

  16. High-order algorithms for solving eigenproblems over discrete surfaces

    CERN Document Server

    Chen, Sheng-Gwo; Wu, Jyh-Yang

    2013-01-01

    The eigenvalue problem of the Laplace-Beltrami operators on curved surfaces plays an essential role in the convergence analysis of the numerical simulations of some important geometric partial differential equations which involve this operator. In this note we shall combine the local tangential lifting (LTL) method with the configuration equation to develop a new effective and convergent algorithm to solve the eigenvalue problems of the Laplace-Beltrami operators acting on functions over discrete surfaces. The convergence rates of our algorithms of discrete Laplace-Beltrami operators over surfaces is $O(r^n)$, $n \\geq 1$, where $r$ represents the size of the mesh of discretization of the surface. The problem of high-order accuracies will also be discussed and used to compute geometric invariants of the underlying surfaces. Some convergence tests and eigenvalue computations on the sphere, tori and a dumbbell are presented.

  17. Highly efficient solid state catalysis by reconstructed (001) Ceria surface

    Energy Technology Data Exchange (ETDEWEB)

    Solovyov, VF; Ozaki, T; Atrei, A; Wu, LJ; Al-Mahboob, A; Sadowski, JT; Tong, X; Nykypanchuk, D; Li, Q

    2014-04-10

    Substrate engineering is a key factor in the synthesis of new complex materials. The substrate surface has to be conditioned in order to minimize the energy threshold for the formation of the desired phase or to enhance the catalytic activity of the substrate. The mechanism of the substrate activity, especially of technologically relevant oxide surfaces, is poorly understood. Here we design and synthesize several distinct and stable CeO2 (001) surface reconstructions which are used to grow epitaxial films of the high-temperature superconductor YBa2Cu3O7. The film grown on the substrate having the longest, fourfold period, reconstruction exhibits a twofold increase in performance over surfaces with shorter period reconstructions. This is explained by the crossover between the nucleation site dimensions and the period of the surface reconstruction. This result opens a new avenue for catalysis mediated solid state synthesis.

  18. Plasma–Surface Interactions Under High Heat and Particle Fluxes

    Directory of Open Access Journals (Sweden)

    Gregory De Temmerman

    2013-01-01

    Full Text Available The plasma-surface interactions expected in the divertor of a future fusion reactor are characterized by extreme heat and particle fluxes interacting with the plasma-facing surfaces. Powerful linear plasma generators are used to reproduce the expected plasma conditions and allow plasma-surface interactions studies under those very harsh conditions. While the ion energies on the divertor surfaces of a fusion device are comparable to those used in various plasma-assited deposition and etching techniques, the ion (and energy fluxes are up to four orders of magnitude higher. This large upscale in particle flux maintains the surface under highly non-equilibrium conditions and bring new effects to light, some of which will be described in this paper.

  19. Quantitative and Qualitative Responses to Topical Cold in Healthy Caucasians Show Variance between Individuals but High Test-Retest Reliability.

    Directory of Open Access Journals (Sweden)

    Penny Moss

    Full Text Available Increased sensitivity to cold may be a predictor of persistent pain, but cold pain threshold is often viewed as unreliable. This study aimed to determine the within-subject reliability and between-subject variance of cold response, measured comprehensively as cold pain threshold plus pain intensity and sensation quality at threshold. A test-retest design was used over three sessions, one day apart. Response to cold was assessed at four sites (thenar eminence, volar forearm, tibialis anterior, plantar foot. Cold pain threshold was measured using a Medoc thermode and standard method of limits. Intensity of pain at threshold was rated using a 10cm visual analogue scale. Quality of sensation at threshold was quantified with indices calculated from subjects' selection of descriptors from a standard McGill Pain Questionnaire. Within-subject reliability for each measure was calculated with intra-class correlation coefficients and between-subject variance was evaluated as group coefficient of variation percentage (CV%. Gender and site comparisons were also made. Forty-five healthy adults participated: 20 male, 25 female; mean age 29 (range 18-56 years. All measures at all four test sites showed high within-subject reliability: cold pain thresholds r = 0.92-0.95; pain rating r = 0.93-0.97; McGill pain quality indices r = 0.87-0.85. In contrast, all measures showed wide between-subject variance (CV% between 51.4% and 92.5%. Upper limb sites were consistently more sensitive than lower limb sites, but equally reliable. Females showed elevated cold pain thresholds, although similar pain intensity and quality to males. Females were also more reliable and showed lower variance for all measures. Thus, although there was clear population variation, response to cold for healthy individuals was found to be highly reliable, whether measured as pain threshold, pain intensity or sensation quality. A comprehensive approach to cold response testing therefore may add

  20. A new loess distribution map for the Carpathian Basin facilitates surface sediment transects and showing migration pathways for modern human dispersal

    Science.gov (United States)

    Lehmkuhl, Frank; Lindner, Heiko; Bösken, Janina; Zeeden, Christian

    2017-04-01

    Quaternary studies in the Carpathian Basin require a detailed knowledge of the distribution of surface sediments. Existing and often cited maps, such as Haase et al. (2007), are not detailed enough for various purposes and difficult in detail as a result of the basic input data and due to the used scale. In addition, many of the maps presenting the distribution of loess and other geological features in Europe display inconsistencies such as displacements, shifts or even abrupt delimitations of different geological units such as loess across national borders. In fact, if geoscientific data from different regions or countries are combined, national borders in many medium- and large-scale thematic datasets appear as artificial breaks. To create a higher resolution map showing the more detailed distribution of Quaternary surface sediments in the Carpathian Basin the spatial data from several countries were used and combined. Particularly some issues occurred because of the thematically content of the underlying international geodata, but also due to geodetical basics such as projections and linguistic barriers, respectively. In addition to maps, transects of surface sediments from the lowlands to the uplands are provided. Together these visualizations are used for discussing the loess distribution and possible origins. This map provides a valuable contribution to the potential migration route for the dispersal of the modern humans. We can show that the distribution of Aurignacian open air sites is connect to elevations between 200 and 500 m at the foothills of the mountains and often situated in loess environments.

  1. [A case of advanced gastric cancer showing high serum CYFRA21-1 level responding to chemotherapy with S-1].

    Science.gov (United States)

    Hara, Akihito; Watanabe, Hiroaki

    2008-12-01

    The patient was a 75-year-old man whose complaint was back pain and appetite loss. He was diagnosed with unresectable advanced gastric cancer due to multiple liver metastases and direct invasion of pancreas and spleen. He underwent gastrostomy because of esophageal stenosis, and we administered S-1 80 mg/body(4 weeks administration and 2 weeks rest)to the patient through a gastrostogavage tube. On blood examination, the serum level of CYFRA21- 1 was significantly high, while those of CEA and CA19-9 were within normal ranges. After the first course of this chemotherapy, the serum CYFRA21-1 level significantly decreased with reduction of the cancer. After the second course, it sensitively increased before image views detected the progression of the cancer. This case shows that CYFRA21- 1 could be a useful tumor marker of advanced gastric cancer.

  2. A New Approach for Surface Energy Calculations Applicable to High-throughput Design of New Interfaces

    Science.gov (United States)

    Ratsch, Christian; Kaminski, Jakub

    In this talk we will present a new approach for the calculation of surface energies of periodic crystal. For non-polar materials slabs (which are terminated by two identical surfaces) the task of calculating the surface energy is trivial. But it is more problematic for polar systems where both terminating surfaces are different, as there is no single established method allowing for equal treatment of a wide range of surface morphologies and orientations. Our proposed new approach addresses this problem. It relies on carefully chosen capping atoms and the assumptions that their bond energy contributions can be used to approximate the total energy of the surface. The choice of the capping atoms is governed by a set of simple guidelines that are applicable for surfaces with different terminations. We present the results for different semiconductor materials and show that our approach leads to surfaces energies with errors as low as 2%. We show that hydrogen is not always the best choice for a capping atom if accurate surface energies are the target of the calculations. Our approach is suitable for high-throughput screening of new material interfaces, as accurate calculations of surface energies can be performed in an unsupervised algorithm. A New Approach for Surface Energy Calculations Applicable to High-throughput Design of New Interfaces.

  3. Methane Seeps in the Gulf of Mexico: repeat acoustic surveying shows highly temporally and spatially variable venting

    Science.gov (United States)

    Beaumont, B. C.; Raineault, N.

    2016-02-01

    Scientists have recognized that natural seeps account for a large amount of methane emissions. Despite their widespread occurrence in areas like the Gulf of Mexico, little is known about the temporal variability and site-scale spatial variability of venting over time. We used repeat acoustic surveys to compare multiple days of seep activity and determine the changes in the locus of methane emission and plume height. The Sleeping Dragon site was surveyed with an EM302 multibeam sonar on three consecutive days in 2014 and 4 days within one week in 2015. The data revealed three distinctive plume regions. The locus of venting varied by 10-60 meters at each site. The plume that exhibited the least spatial variability in venting, was also the most temporally variable. This seep was present in one-third of survey dates in 2014 and three quarters of survey dates in 2015, showing high day-to-day variability. The plume height was very consistent for this plume, whereas the other plumes were more consistent temporally, but varied in maximum plume height detection by 25-85 m. The single locus of emission at the site that had high day-to-day variability may be due to a single conduit for methane release, which is sometimes closed off by carbonate or clathrate hydrate formation. In addition to day-to-day temporal variability, the locus of emission at one site was observed to shift from a point-source in 2014 to a diffuse source in 2015 at a nearby location. ROV observations showed that one of the seep sites that closed off temporarily, experienced an explosive breakthrough of gas, releasing confined methane and blowing out rock. The mechanism that causes on/off behavior of certain plumes, combined with the spatial variability of the locus of methane release shown in this study may point to carbonate or hydrate formation in the seep plumbing system and should be further investigated.

  4. Blistering on tungsten surface exposed to high flux deuterium plasma

    NARCIS (Netherlands)

    Xu, H.Y.; Liu, W.; Luo, G. N.; Yuan, Y.; Jia, Y. Z.; Fu, B. Q.; De Temmerman, G.

    2016-01-01

    The blistering behaviour of tungsten surfaces exposed to very high fluxes (1–2 × 1024/m2/s) of low energy (38 eV) deuterium plasmas was investigated as a function of ion fluence (0.2–7 × 1026 D/m2) and surface temperature (423–873 K). Blisters were observed under all conditions, especially up to

  5. High surface area carbon and process for its production

    Science.gov (United States)

    Romanos, Jimmy; Burress, Jacob; Pfeifer, Peter; Rash, Tyler; Shah, Parag; Suppes, Galen

    2016-12-13

    Activated carbon materials and methods of producing and using activated carbon materials are provided. In particular, biomass-derived activated carbon materials and processes of producing the activated carbon materials with prespecified surface areas and pore size distributions are provided. Activated carbon materials with preselected high specific surface areas, porosities, sub-nm (carbon consumption and metallic potassium intercalation into the carbon lattice during the activation process.

  6. High-resolution analysis of protons scattered from solid surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Matsunami, Noriaki; Kitoh, Kenshin (Dept. of Crystalline Materials Science, Engineering, Nagoya Univ. (Japan)); Kanasaki, Jun-ichi; Itoh, Noriaki (Physics Dept., Nagoya Univ. (Japan))

    1990-01-01

    A survey is given for new information that can be obtained by high energy-resolution analysis of protons backscattered from solid surfaces: layer-by-layer analysis of composition, atomic and electronic structures of surfaces. Optimization of the scattering yield leads to the result that scattering geometries of both glancing angle (PELS-I) and 180deg (PELS-II) are feasible. Results obtained by PELS-I are mainly described: Au atom location for Au/Si(111) and surface contraction of W(111). The impact parameter-dependent inelastic energy loss function is mentioned. (orig.).

  7. Surface interactions involved in flashover with high density electronegative gases.

    Energy Technology Data Exchange (ETDEWEB)

    Hodge, Keith Conquest; Warne, Larry Kevin; Jorgenson, Roy Eberhardt; Wallace, Zachariah Red; Lehr, Jane Marie

    2010-01-01

    This report examines the interactions involved with flashover along a surface in high density electronegative gases. The focus is on fast ionization processes rather than the later time ionic drift or thermalization of the discharge. A kinetic simulation of the gas and surface is used to examine electron multiplication and includes gas collision, excitation and ionization, and attachment processes, gas photoionization and surface photoemission processes, as well as surface attachment. These rates are then used in a 1.5D fluid ionization wave (streamer) model to study streamer propagation with and without the surface in air and in SF6. The 1.5D model therefore includes rates for all these processes. To get a better estimate for the behavior of the radius we have studied radial expansion of the streamer in air and in SF6. The focus of the modeling is on voltage and field level changes (with and without a surface) rather than secondary effects, such as, velocities or changes in discharge path. An experiment has been set up to carry out measurements of threshold voltages, streamer velocities, and other discharge characteristics. This setup includes both electrical and photographic diagnostics (streak and framing cameras). We have observed little change in critical field levels (where avalanche multiplication sets in) in the gas alone versus with the surface. Comparisons between model calculations and experimental measurements are in agreement with this. We have examined streamer sustaining fields (field which maintains ionization wave propagation) in the gas and on the surface. Agreement of the gas levels with available literature is good and agreement between experiment and calculation is good also. Model calculations do not indicate much difference between the gas alone versus the surface levels. Experiments have identified differences in velocity between streamers on the surface and in the gas alone (the surface values being larger).

  8. Mn(II)-based porous metal-organic framework showing metamagnetic properties and high hydrogen adsorption at low pressure.

    Science.gov (United States)

    Han, Zheng-Bo; Lu, Rui-Yun; Liang, Yan-Fang; Zhou, Yan-Ling; Chen, Qing; Zeng, Ming-Hua

    2012-01-02

    A Mn(II)-based homometallic porous metal-organic framework, Mn(5)(btac)(4)(μ(3)-OH)(2)(EtOH)(2)·DMF·3EtOH·3H(2)O (1, btac = benzotriazole-5-carboxylate), has been solvothermally synthesized and structurally characterized by elemental analysis, thermogravimetric analysis, and X-ray crystallographic study. 1 is a 3D neutral framework featuring 1D porous channels constructed by {Mn-OH-Mn}(n) chains and btac linkers. Magnetic studies show that 1 is a 3D metamagnet containing 1D {Mn-OH-Mn}(n) ferrimagnetic chains. High-pressure H(2) adsorption measurement at 77 K reveals that activated 1 can absorb 0.99 wt % H(2) at 0.5 atm and reaches a maximum of 1.03 wt % at 5.5 atm. The steep H(2) absorption at lower pressure (98.2% of the storage capacity at 0.5 atm) is higher than the corresponding values of some MOFs (MIL-100 (16.1%), MOF-177 (57.1%), and MOF-5 (22.2%)). Furthermore, activated 1 can adsorb CO(2) at room temperature and 275 K. The adsorption enthalpy is 22.0 kJ mol(-1), which reveals the high binding ability for CO(2). Detailed gas sorption implies that the exposed Mn(II) coordination sites in the activated 1 play an important role to improve its adsorption capacities.

  9. A novel 5-enolpyruvylshikimate-3-phosphate synthase shows high glyphosate tolerance in Escherichia coli and tobacco plants.

    Directory of Open Access Journals (Sweden)

    Gaoyi Cao

    Full Text Available A key enzyme in the shikimate pathway, 5-enolpyruvylshikimate-3-phosphate synthase (EPSPS is the primary target of the broad-spectrum herbicide glyphosate. Identification of new aroA genes coding for EPSPS with a high level of glyphosate tolerance is essential for the development of glyphosate-tolerant crops. In the present study, the glyphosate tolerance of five bacterial aroA genes was evaluated in the E. coli aroA-defective strain ER2799 and in transgenic tobacco plants. All five aroA genes could complement the aroA-defective strain ER2799, and AM79 aroA showed the highest glyphosate tolerance. Although glyphosate treatment inhibited the growth of both WT and transgenic tobacco plants, transgenic plants expressing AM79 aroA tolerated higher concentration of glyphosate and had a higher fresh weight and survival rate than plants expressing other aroA genes. When treated with high concentration of glyphosate, lower shikimate content was detected in the leaves of transgenic plants expressing AM79 aroA than transgenic plants expressing other aroA genes. These results suggest that AM79 aroA could be a good candidate for the development of transgenic glyphosate-tolerant crops.

  10. Oral noribogaine shows high brain uptake and anti-withdrawal effects not associated with place preference in rodents.

    Science.gov (United States)

    Mash, Deborah C; Ameer, Barbara; Prou, Delphine; Howes, John F; Maillet, Emeline L

    2016-07-01

    This study investigated the effects of noribogaine, the principal metabolite of the drug ibogaine, on substance-related disorders. In the first experiment, mice chronically treated with morphine were subjected to naloxone-precipitated withdrawal two hours after oral administration of noribogaine. Oral noribogaine dose dependently decreased the global opiate withdrawal score by up to 88% of vehicle control with an ED50 of 13 mg/kg. In the second experiment, blood and brain levels of noribogaine showed a high brain penetration and a brain/blood ratio of 7±1 across all doses tested. In a third experiment, rats given oral noribogaine up to 100 mg/kg were tested for abuse liability using a standard biased conditioned place paradigm. Noribogaine-treated rats did not display place preference, suggesting that noribogaine is not perceived as a hedonic stimulus in rodents. Retrospective review of published studies assessing the efficacy of ibogaine on morphine withdrawal shows that the most likely cause of the discrepancies in the literature is the different routes of administration and time of testing following ibogaine administration. These results suggest that the metabolite noribogaine rather than the parent compound mediates the effects of ibogaine on blocking naloxone-precipitated withdrawal. Noribogaine may hold promise as a non-addicting alternative to standard opiate replacement therapies to transition patients to opiate abstinence.

  11. Blistering on tungsten surface exposed to high flux deuterium plasma

    Energy Technology Data Exchange (ETDEWEB)

    Xu, H.Y., E-mail: donaxu@163.com [Center of Interface Dynamics for Sustainability, Institute of Materials, CAEP, Chengdu 610200 (China); Key Laboratory of Advanced Materials, School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Liu, W., E-mail: liuw@mail.tsinghua.edu.cn [Key Laboratory of Advanced Materials, School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Luo, G.N. [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Yuan, Y. [School of Physics and Nuclear Energy Engineering, Beihang University, Beijing 100191 (China); Jia, Y.Z.; Fu, B.Q. [Key Laboratory of Advanced Materials, School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); De Temmerman, G. [FOM Institute DIFFER-Dutch Institute for Fundamental Energy Research, Trilateral Euregio Cluster, Edisonbaan 14, 3439 MN Nieuwegein (Netherlands); ITER Organization, Route de Vinon-sur-Verdon CS 90046-13067, St Paul Lez Durance Cedex (France)

    2016-04-01

    The blistering behaviour of tungsten surfaces exposed to very high fluxes (1–2 × 10{sup 24}/m{sup 2}/s) of low energy (38 eV) deuterium plasmas was investigated as a function of ion fluence (0.2–7 × 10{sup 26} D/m{sup 2}) and surface temperature (423–873 K). Blisters were observed under all conditions, especially up to temperatures of 873 K. The blister parameters are evaluated with blister size, blister density and surface coverage. The blister size always peaked at less than 0.5 μm and no blister larger than 10 μm is observed even at high fluence. The blister densities are found in high magnitude of 10{sup 6} blisters/m{sup 2}, with the surface coverages lower than 2%. The formation of cracks in the sub-surface region was observed by cross-section imaging. Changes in blister size and shape with fluence and temperature suggest processes of predominantly nucleation and subsequent growth of blisters. The smaller blister size is considered to be caused by a combination of flux-related effects such as enhanced defect formation in the near surface region, reduced deuterium diffusivity and relatively short exposure times.

  12. Blistering on tungsten surface exposed to high flux deuterium plasma

    Science.gov (United States)

    Xu, H. Y.; Liu, W.; Luo, G. N.; Yuan, Y.; Jia, Y. Z.; Fu, B. Q.; De Temmerman, G.

    2016-04-01

    The blistering behaviour of tungsten surfaces exposed to very high fluxes (1-2 × 1024/m2/s) of low energy (38 eV) deuterium plasmas was investigated as a function of ion fluence (0.2-7 × 1026 D/m2) and surface temperature (423-873 K). Blisters were observed under all conditions, especially up to temperatures of 873 K. The blister parameters are evaluated with blister size, blister density and surface coverage. The blister size always peaked at less than 0.5 μm and no blister larger than 10 μm is observed even at high fluence. The blister densities are found in high magnitude of 106 blisters/m2, with the surface coverages lower than 2%. The formation of cracks in the sub-surface region was observed by cross-section imaging. Changes in blister size and shape with fluence and temperature suggest processes of predominantly nucleation and subsequent growth of blisters. The smaller blister size is considered to be caused by a combination of flux-related effects such as enhanced defect formation in the near surface region, reduced deuterium diffusivity and relatively short exposure times.

  13. High-Density Infrared Surface Treatments of Refractories

    Energy Technology Data Exchange (ETDEWEB)

    Tiegs, T.N.

    2005-03-31

    Refractory materials play a crucial role in all energy-intensive industries and are truly a crosscutting technology for the Industries of the Future (IOF). One of the major mechanisms for the degradation of refractories and a general decrease in their performance has been the penetration and corrosion by molten metals or glass. Methods and materials that would reduce the penetration, wetting, and corrosive chemistry would significantly improve refractory performance and also maintain the quality of the processed liquid, be it metal or glass. This report presents the results of an R&D project aimed at investigating the use of high-density infrared (HDI) heating to surface treat refractories to improve their performance. The project was a joint effort between Oak Ridge National Laboratory (ORNL) and the University of Missouri-Rolla (UMR). HDI is capable of heating the near-surface region of materials to very high temperatures where sintering, diffusion, and melting can occur. The intended benefits of HDI processing of refractories were to (1) reduce surface porosity (by essentially sealing the surface to prevent liquid penetration), (2) allow surface chemistry changes to be performed by bonding an adherent coating onto the underlying refractory (in order to inhibit wetting and/or improve corrosion resistance), and (3) produce noncontact refractories with high-emissivity surface coatings.

  14. Tree Rings Show Recent High Summer-Autumn Precipitation in Northwest Australia Is Unprecedented within the Last Two Centuries.

    Directory of Open Access Journals (Sweden)

    Alison J O'Donnell

    Full Text Available An understanding of past hydroclimatic variability is critical to resolving the significance of recent recorded trends in Australian precipitation and informing climate models. Our aim was to reconstruct past hydroclimatic variability in semi-arid northwest Australia to provide a longer context within which to examine a recent period of unusually high summer-autumn precipitation. We developed a 210-year ring-width chronology from Callitris columellaris, which was highly correlated with summer-autumn (Dec-May precipitation (r = 0.81; 1910-2011; p < 0.0001 and autumn (Mar-May self-calibrating Palmer drought severity index (scPDSI, r = 0.73; 1910-2011; p < 0.0001 across semi-arid northwest Australia. A linear regression model was used to reconstruct precipitation and explained 66% of the variance in observed summer-autumn precipitation. Our reconstruction reveals inter-annual to multi-decadal scale variation in hydroclimate of the region during the last 210 years, typically showing periods of below average precipitation extending from one to three decades and periods of above average precipitation, which were often less than a decade. Our results demonstrate that the last two decades (1995-2012 have been unusually wet (average summer-autumn precipitation of 310 mm compared to the previous two centuries (average summer-autumn precipitation of 229 mm, coinciding with both an anomalously high frequency and intensity of tropical cyclones in northwest Australia and the dominance of the positive phase of the Southern Annular Mode.

  15. Apolipoprotein E-knockout mice on high-fat diet show autoimmune injury on kidney and aorta

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Yuehai [Cardiovascular Department, Liaocheng People’s Hospital of Shandong University, Liaocheng, Shandong 252000 (China); Cardiovascular Department, The Second Clinical Medical College of Fujian Medical University, Quanzhou, Fujian 362000 (China); Lu, Huixia [The Key Laboratory of Cardiovascular Remodeling and Function Research, Chinese Ministry of Education and Chinese Ministry of Health, Shandong University Qilu Hospital, Jinan, Shandong 250012 (China); Huang, Ziyang, E-mail: huangziyang666@126.com [Cardiovascular Department, The Second Clinical Medical College of Fujian Medical University, Quanzhou, Fujian 362000 (China); Lin, Huili [Cardiovascular Department, The Second Clinical Medical College of Fujian Medical University, Quanzhou, Fujian 362000 (China); Lei, Zhenmin [Department of OB/GYN, University of Louisville School of Medicine, Louisville, KY 40292 (United States); Chen, Xiaoqing [Department of Rheumatism and Immunology, The Second Clinical Medical College of Fujian Medical University, Quanzhou, Fujian 362000 (China); Tang, Mengxiong; Gao, Fei; Dong, Mei [The Key Laboratory of Cardiovascular Remodeling and Function Research, Chinese Ministry of Education and Chinese Ministry of Health, Shandong University Qilu Hospital, Jinan, Shandong 250012 (China); Li, Rongda [Department of Rheumatism and Immunology, The Second Clinical Medical College of Fujian Medical University, Quanzhou, Fujian 362000 (China); Lin, Ling, E-mail: qzlinl@163.com [Department of Rheumatism and Immunology, The Second Clinical Medical College of Fujian Medical University, Quanzhou, Fujian 362000 (China)

    2014-07-18

    Highlights: • Titers of ANA and anti-dsDNA antibodies were similar in ApoE{sup −/−} and Fas{sup −/−} mice. • The spleen weights and glomerular areas were similar in ApoE{sup −/−} and Fas{sup −/−} mice. • Expressions of IgG and C3 in glomeruli were similar in ApoE{sup −/−} and Fas{sup −/−} mice. • IgG, C3 and macrophage infiltration in aortic plaques were found in ApoE{sup −/−} mice. - Abstract: Background: Apolipoprotein E-knockout (ApoE{sup −/−}) mice is a classic model of atherosclerosis. We have found that ApoE{sup −/−} mice showed splenomegaly, higher titers of serum anti-nuclear antibody (ANA) and anti-dsDNA antibody compared with C57B6/L (B6) mice. However, whether ApoE{sup −/−} mice show autoimmune injury remains unclear. Methods and results: Six females and six males in each group, ApoE{sup −/−}, Fas{sup −/−} and B6 mice, were used in this study. The titers of serum ANA, anti-dsDNA antibody and creatinine and urine protein were measured by ELISA after 4 months of high-fat diet. The spleen weight and the glomerular area were determined. The expressions of IgG, C3 and macrophage in kidney and atherosclerotic plaque were detected by immunostaining followed by morphometric analysis. Similar to the characteristics of Fas{sup −/−} mice, a model of systemic lupus erythematosus (SLE), ApoE{sup −/−} mice, especially female, displayed significant increases of spleen weight and glomerular area when compared to B6 mice. Also, elevated titers of serum ANA, anti-dsDNA antibody and creatinine and urine protein. Moreover, the expressions of IgG, C3 and macrophage in glomeruli and aortic plaques were found in ApoE{sup −/−} mice. In addition, the IgG and C3 expressions in glomeruli and plaques significantly increased (or a trend of increase) in female ApoE{sup −/−} mice compared with males. Conclusions: Apolipoprotein E-knockout mice on high-fat diet show autoimmune injury on kidney and aorta.

  16. The use of a well-defined surface organometallic complex as a probe molecule: [(SiO)TaVCl2Me2] shows different isolated silanol sites on the silica surface

    KAUST Repository

    Chen, Yin

    2014-01-01

    TaVCl2Me3 reacts with silica(700) and produces two different [(SiO)TaVCl2Me2] surface organometallic species, suggesting a heterogeneity of the highly dehydroxylated silica surface, which was studied with a combined experimental and theoretical approach. This journal is © the Partner Organisations 2014.

  17. Nanostructures and pinholes on W surfaces exposed to high flux D plasma at high temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Jia, Y.Z., E-mail: jaja880816@aliyun.com [Laboratory of Advanced Materials, School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Liu, W., E-mail: liuw@mail.tsinghua.edu.cn [Laboratory of Advanced Materials, School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Xu, B. [Laboratory of Advanced Materials, School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Luo, G.-N. [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Li, C.; Fu, B.Q. [Laboratory of Advanced Materials, School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); De Temmerman, G. [FOM Institute DIFFER-Dutch Institute for Fundamental Energy Research, Edisonbaan 14, 3439 MN Nieuwegein (Netherlands); ITER Organization, Route de Vinon-Sur-Verdon, CS 90 046, 13067 St Paul Lez Durance Cedex (France)

    2015-08-15

    Nanostructures and pinholes formed on tungsten surface exposed to high fluxes (10{sup 24} m{sup −2} s{sup −1}) deuterium ions at 943 K and 1073 K were studied by scanning electron microscopy and electron backscatter diffraction. Nanostructure formation is observed at 943 K and 1073 K, and exhibits a strong dependence on the surface orientation. With increasing fluence, pinholes appear on the surface and are mainly observed on grains with surface normal near [1 1 1]. The pinholes are speculated to be caused by the rupture of bubbles formed near the surface. The formation of pinholes has no obvious relationship with the surface nanostructures.

  18. Sub-surface and surface analysis of high speed machined Ti-6Al-4V alloy

    Energy Technology Data Exchange (ETDEWEB)

    Velasquez, J.D. Puerta [Laboratoire d' Etude des Textures et Applications aux Materiaux (LETAM), CNRS FRE 3143, Ecole Nationale d' Ingenieurs de Metz (ENIM), F-57012 Metz Cedex 01 (France); Tidu, A., E-mail: tidu@enim.fr [Laboratoire d' Etude des Textures et Applications aux Materiaux (LETAM), CNRS FRE 3143, Ecole Nationale d' Ingenieurs de Metz (ENIM), F-57012 Metz Cedex 01 (France); Bolle, B. [Laboratoire d' Etude des Textures et Applications aux Materiaux (LETAM), CNRS FRE 3143, Ecole Nationale d' Ingenieurs de Metz (ENIM), F-57012 Metz Cedex 01 (France); Chevrier, P. [Laboratoire de Mecanique Biomecanique, Polymere Structures (LaBPS), EA 4632 Ecole Nationale d' Ingenieurs de Metz (ENIM), F-57012 Metz Cedex 01 (France); Fundenberger, J.-J. [Laboratoire d' Etude des Textures et Applications aux Materiaux (LETAM), CNRS FRE 3143, Universite Paul Verlaine de Metz (UPVM), F-57012 Metz Cedex 01 (France)

    2010-04-25

    To understand the effects of cutting the surface integrity is an important goal to control the quality of a work piece. The current paper summarizes an extensive experimental study of the surface integrity and the sub-surface microstructure during high speed machining in orthogonal cutting condition. This study includes measurements of residual stresses and crystallographic texture in addition to electron microscopy observations. Our observations and conclusions are primarily focused on the effect of cutting speed considering a set of constant machining parameters on the microstructure evolution of the sub-surface of the material. The results allow a better understanding of the cutting process in high speed machining of titanium alloy Ti-6Al-4V.

  19. Grow Large High-Quality Diamonds with Different Seed Surfaces

    Institute of Scientific and Technical Information of China (English)

    ZANG Chuan-Yi; JIA Xiao-Peng; MA Hong-An; LI Shang-Sheng; TIAN Yu; XIAO Hong-Yu

    2006-01-01

    Large high-quality type Ib diamond crystals have been grown with different seed surfaces by temperature gradient method at 5.5GPa, 1500-1600K, with NiMnCo alloy as the metal solvent. Compared with {100} as the growth surface, the growth region of large high-quality diamond crystals with {111} as the growth surface at a higher growth rate shifts markedly from lower temperatures (suitable for {100}-facet growth) to higher temperatures (suitable for {lll}-facet growth). However, regardless of different growth surfaces, {100} or {111}, the grown crystals of sheet-shaped shape are most difficult for metal inclusions to be trapped into, and whether or not matched growth between the seed surfaces and the growth temperatures determines the crystal shapes. In view of the growth rates, large high-quality diamond crystals of sheet-shaped shapes can be grown at a growth rate of above 2.5mg/h, while the growth rate of large high-quality diamond crystals should not be beyond 1.5mg/h for tower-shaped crystals.

  20. High-Temperature Surface-Acoustic-Wave Transducer

    Science.gov (United States)

    Zhao, Xiaoliang; Tittmann, Bernhard R.

    2010-01-01

    Aircraft-engine rotating equipment usually operates at high temperature and stress. Non-invasive inspection of microcracks in those components poses a challenge for the non-destructive evaluation community. A low-profile ultrasonic guided wave sensor can detect cracks in situ. The key feature of the sensor is that it should withstand high temperatures and excite strong surface wave energy to inspect surface/subsurface cracks. As far as the innovators know at the time of this reporting, there is no existing sensor that is mounted to the rotor disks for crack inspection; the most often used technology includes fluorescent penetrant inspection or eddy-current probes for disassembled part inspection. An efficient, high-temperature, low-profile surface acoustic wave transducer design has been identified and tested for nondestructive evaluation of structures or materials. The development is a Sol-Gel bismuth titanate-based surface-acoustic-wave (SAW) sensor that can generate efficient surface acoustic waves for crack inspection. The produced sensor is very thin (submillimeter), and can generate surface waves up to 540 C. Finite element analysis of the SAW transducer design was performed to predict the sensor behavior, and experimental studies confirmed the results. One major uniqueness of the Sol-Gel bismuth titanate SAW sensor is that it is easy to implement to structures of various shapes. With a spray coating process, the sensor can be applied to surfaces of large curvatures. Second, the sensor is very thin (as a coating) and has very minimal effect on airflow or rotating equipment imbalance. Third, it can withstand temperatures up to 530 C, which is very useful for engine applications where high temperature is an issue.

  1. Hyperspectral surface materials map of quadrangle 3262, Farah (421) and Hokumat-e-pur-Chaman (422) quadrangles, Afghanistan, showing carbonates, phyllosilicates, sulfates, altered minerals, and other materials

    Science.gov (United States)

    Kokaly, Raymond F.; King, Trude V.V.; Hoefen, Todd M.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

    2013-01-01

    This map shows the spatial distribution of selected carbonates, phyllosilicates, sulfates, altered minerals, and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. The map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Epidote or chlorite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  2. Hyperspectral surface materials map of quadrangle 3468, Chak-e Wardak-Siyahgird (509) and Kabul (510) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

    Science.gov (United States)

    King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Giles, Stuart A.; Johnson, Michaela R.

    2013-01-01

    This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  3. Hyperspectral surface materials map of quadrangle 3164, Lashkar Gah (605) and Kandahar (606) quadrangles, Afghanistan, showing carbonates, phyllosilicates, sulfates, altered minerals, and other materials

    Science.gov (United States)

    Kokaly, Raymond F.; King, Trude V.V.; Hoefen, Todd M.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

    2013-01-01

    This map shows the spatial distribution of selected carbonates, phyllosilicates, sulfates, altered minerals, and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. The map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Epidote or chlorite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  4. Hyperspectral surface materials map of quadrangle 3166, Jaldak (701) and Maruf-Nawa (702) quadrangles, Afghanistan, showing carbonates, phyllosilicates, sulfates, altered minerals, and other materials

    Science.gov (United States)

    Kokaly, Raymond F.; King, Trude V.V.; Hoefen, Todd M.; Livo, Keith E.; Giles, Stuart A.; Johnson, Michaela R.

    2013-01-01

    This map shows the spatial distribution of selected carbonates, phyllosilicates, sulfates, altered minerals, and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. The map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Epidote or chlorite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  5. Hyperspectral surface materials map of quadrangle 3568, Pul-e Khumri (503) and Charikar (504) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

    Science.gov (United States)

    King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

    2013-01-01

    This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  6. Hyperspectral surface materials map of quadrangle 3466, La`l wa Sar Jangal (507) and Bamyan (508) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

    Science.gov (United States)

    King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Giles, Stuart A.; Johnson, Michaela R.

    2013-01-01

    This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  7. Hyperspectral surface materials map of quadrangle 3268, Khayr Kot (521) and Urgun (522) quadrangles, Afghanistan, showing carbonates, phyllosilicates, sulfates, altered minerals, and other materials

    Science.gov (United States)

    Kokaly, Raymond F.; King, Trude V.V.; Hoefen, Todd M.; Livo, Keith E.; Giles, Stuart A.; Johnson, Michaela R.

    2013-01-01

    This map shows the spatial distribution of selected carbonates, phyllosilicates, sulfates, altered minerals, and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. The map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Epidote or chlorite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  8. Hyperspectral surface materials map of quadrangle 3564, Jowand (405) and Gurziwan (406) quadrangles, Afghanistan, showing carbonates, phyllosilicates, sulfates, altered minerals, and other materials

    Science.gov (United States)

    Kokaly, Raymond F.; King, Trude V.V.; Hoefen, Todd M.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

    2013-01-01

    This map shows the spatial distribution of selected carbonates, phyllosilicates, sulfates, altered minerals, and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. The map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Epidote or chlorite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  9. Hyperspectral surface materials map of quadrangle 3466, La`l wa Sar Jangal (507) and Bamyan (508) quadrangles, Afghanistan, showing carbonates, phyllosilicates, sulfates, altered minerals, and other materials

    Science.gov (United States)

    Kokaly, Raymond F.; King, Trude V.V.; Hoefen, Todd M.; Livo, Keith E.; Giles, Stuart A.; Johnson, Michaela R.

    2013-01-01

    This map shows the spatial distribution of selected carbonates, phyllosilicates, sulfates, altered minerals, and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. The map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Epidote or chlorite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  10. Hyperspectral surface materials map of quadrangle 3670, Jurm-Kishim (223) and Zebak (224) quadrangles, Afghanistan, showing carbonates, phyllosilicates, sulfates, altered minerals, and other materials

    Science.gov (United States)

    Kokaly, Raymond F.; King, Trude V.V.; Hoefen, Todd M.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

    2013-01-01

    This map shows the spatial distribution of selected carbonates, phyllosilicates, sulfates, altered minerals, and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. The map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Epidote or chlorite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  11. Hyperspectral surface materials map of quadrangle 3368, Ghazni (515) and Gardez (516) quadrangles, Afghanistan, showing carbonates, phyllosilicates, sulfates, altered minerals, and other materials

    Science.gov (United States)

    Kokaly, Raymond F.; King, Trude V.V.; Hoefen, Todd M.; Livo, Keith E.; Giles, Stuart A.; Johnson, Michaela R.

    2013-01-01

    This map shows the spatial distribution of selected carbonates, phyllosilicates, sulfates, altered minerals, and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. The map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Epidote or chlorite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  12. Hyperspectral surface materials map of quadrangle 3266, Uruzgan (519) and Moqur (520) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

    Science.gov (United States)

    King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Giles, Stuart A.; Johnson, Michaela R.

    2013-01-01

    This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  13. Hyperspectral surface materials map of quadrangle 3164, Lashkar Gah (605) and Kandahar (606) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

    Science.gov (United States)

    King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

    2013-01-01

    This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  14. Hyperspectral surface materials map of quadrangle 3366, Gizab (513) and Nawer (514) quadrangles, Afghanistan, showing carbonates, phyllosilicates, sulfates, altered minerals, and other materials

    Science.gov (United States)

    Kokaly, Raymond F.; King, Trude V.V.; Hoefen, Todd M.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

    2013-01-01

    This map shows the spatial distribution of selected carbonates, phyllosilicates, sulfates, altered minerals, and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. The map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Epidote or chlorite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  15. Hyperspectral surface materials map of quadrangle 3770, Faizabad (217) and Parkhaw (218) quadrangles, Afghanistan, showing carbonates, phyllosilicates, sulfates, altered minerals, and other materials

    Science.gov (United States)

    Kokaly, Raymond F.; King, Trude V.V.; Hoefen, Todd M.; Livo, Keith E.; Giles, Stuart A.; Johnson, Michaela R.

    2013-01-01

    This map shows the spatial distribution of selected carbonates, phyllosilicates, sulfates, altered minerals, and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. The map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Epidote or chlorite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  16. Hyperspectral surface materials map of quadrangle 3470, Jalalabad (511) and Chaghasaray (512) quadrangles, Afghanistan, showing carbonates, phyllosilicates, sulfates, altered minerals, and other materials

    Science.gov (United States)

    Kokaly, Raymond F.; King, Trude V.V.; Hoefen, Todd M.; Livo, Keith E.; Giles, Stuart A.; Johnson, Michaela R.

    2013-01-01

    This map shows the spatial distribution of selected carbonates, phyllosilicates, sulfates, altered minerals, and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. The map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Epidote or chlorite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  17. Hyperspectral surface materials map of quadrangle 3464, Shahrak (411) and Kasi (412) quadrangles, Afghanistan, showing carbonates, phyllosilicates, sulfates, altered minerals, and other materials

    Science.gov (United States)

    Kokaly, Raymond F.; King, Trude V.V.; Hoefen, Todd M.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

    2013-01-01

    This map shows the spatial distribution of selected carbonates, phyllosilicates, sulfates, altered minerals, and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. The map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Epidote or chlorite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  18. Hyperspectral Surface Materials Map of Quadrangle 3268, Khayr Kot (521) and Urgun (522) Quadrangles, Afghanistan, Showing Iron-bearing Minerals and Other Materials

    Science.gov (United States)

    King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Giles, Stuart A.; Johnson, Michaela R.

    2013-01-01

    This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  19. Hyperspectral surface materials map of quadrangle 3470, Jalalabad (511) and Chaghasaray (512) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

    Science.gov (United States)

    King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Giles, Stuart A.; Johnson, Michaela R.

    2013-01-01

    This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  20. Hyperspectral surface materials map of quadrangle 3260, Dasht-e-Chah-e-Mazar (419) and Anar Darah (420) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

    Science.gov (United States)

    King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

    2013-01-01

    This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  1. Hyperspectral surface materials map of quadrangle 3266, Uruzgan (519) and Moqur (520) quadrangles, Afghanistan, showing carbonates, phyllosilicates, sulfates, altered minerals, and other materials

    Science.gov (United States)

    Kokaly, Raymond F.; King, Trude V.V.; Hoefen, Todd M.; Livo, Keith E.; Giles, Stuart A.; Johnson, Michaela R.

    2013-01-01

    This map shows the spatial distribution of selected carbonates, phyllosilicates, sulfates, altered minerals, and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. The map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Epidote or chlorite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  2. Hyperspectral surface materials map of quadrangle 3568, Pul-e Khumri (503) and Charikar (504) quadrangles, Afghanistan, showing carbonates, phyllosilicates, sulfates, altered minerals, and other materials

    Science.gov (United States)

    Kokaly, Raymond F.; King, Trude V.V.; Hoefen, Todd M.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

    2013-01-01

    This map shows the spatial distribution of selected carbonates, phyllosilicates, sulfates, altered minerals, and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. The map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Epidote or chlorite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  3. Hyperspectral surface materials map of quadrangle 3562, Khawja-Jir (403) and Murghab (404) quadrangles, Afghanistan, showing carbonates, phyllosilicates, sulfates, altered minerals, and other materials

    Science.gov (United States)

    Kokaly, Raymond F.; King, Trude V.V.; Hoefen, Todd M.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

    2013-01-01

    This map shows the spatial distribution of selected carbonates, phyllosilicates, sulfates, altered minerals, and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. The map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Epidote or chlorite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  4. Hyperspectral surface materials map of quadrangle 3364, Pasaband (417) and Markaz-e Kajiran (418) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

    Science.gov (United States)

    King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

    2013-01-01

    This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  5. Hyperspectral surface materials map of quadrangle 3770, Faizabad (217) and Parkhaw (218) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

    Science.gov (United States)

    King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Giles, Stuart A.; Johnson, Michaela R.

    2013-01-01

    This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  6. Hyperspectral surface materials map of quadrangle 3162, Chakhansur (603) and Kotalak (604) quadrangles, Afghanistan, showing carbonates, phyllosilicates, sulfates, altered minerals, and other materials

    Science.gov (United States)

    Kokaly, Raymond F.; King, Trude V.V.; Hoefen, Todd M.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

    2013-01-01

    This map shows the spatial distribution of selected carbonates, phyllosilicates, sulfates, altered minerals, and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. The map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Epidote or chlorite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  7. Hyperspectral surface materials map of quadrangle 3562, Khawja-Jir (403) and Murghab (404) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

    Science.gov (United States)

    King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

    2013-01-01

    This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  8. Hyperspectral surface materials map of quadrangle 3262, Farah (421) and Hokumat-e-pur-Chaman (422) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

    Science.gov (United States)

    King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

    2013-01-01

    This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  9. Hyperspectral surface materials map of quadrangle 3264, Naw Zad-Musa Qala (423) and Dihrawud (424) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

    Science.gov (United States)

    King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

    2013-01-01

    This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  10. Hyperspectral surface materials map of quadrangle 3570, Tagab-e-Munjan (505) and Asmar-Kamdesh (506) quadrangles, Afghanistan, showing carbonates, phyllosilicates, sulfates, altered minerals, and other materials

    Science.gov (United States)

    Kokaly, Raymond F.; King, Trude V.V.; Hoefen, Todd M.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

    2013-01-01

    This map shows the spatial distribution of selected carbonates, phyllosilicates, sulfates, altered minerals, and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. The map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Epidote or chlorite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  11. Hyperspectral surface materials map of quadrangle 3366, Gizab (513) and Nawer (514) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

    Science.gov (United States)

    King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

    2013-01-01

    This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  12. Hyperspectral surface materials map of quadrangle 3464, Shahrak (411) and Kasi (412) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

    Science.gov (United States)

    King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

    2013-01-01

    This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  13. Hyperspectral surface materials map of quadrangle 3570, Tagab-e-Munjan (505) and Asmar-Kamdesh (506) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

    Science.gov (United States)

    King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

    2013-01-01

    This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  14. Hyperspectral surface materials map of quadrangle 3462, Herat (409) and Chishti Sharif (410) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

    Science.gov (United States)

    King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

    2013-01-01

    This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  15. Hyperspectral surface materials map of quadrangle 3566, Sangcharak (501) and Sayghan-o-Kamard (502) quadrangles, Afghanistan, showing iron-bearing minerals and other material

    Science.gov (United States)

    King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Giles, Stuart A.; Johnson, Michaela R.

    2013-01-01

    This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  16. Hyperspectral surface materials map of quadrangle 3564, Jowand (405) and Gurziwan (406) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

    Science.gov (United States)

    King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

    2013-01-01

    This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  17. Hyperspectral surface materials map of quadrangle 3362, Shindand (415) and Tulak (416) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

    Science.gov (United States)

    King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Giles, Stuart A.; Johnson, Michaela R.

    2013-01-01

    This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  18. Hyperspectral surface materials map of quadrangle 3468, Chak-e Wardak-Siyahgird (509) and Kabul (510) quadrangles, Afghanistan, showing carbonates, phyllosilicates, sulfates, altered minerals, and other materials

    Science.gov (United States)

    Kokaly, Raymond F.; King, Trude V.V.; Hoefen, Todd M.; Livo, Keith E.; Giles, Stuart A.; Johnson, Michaela R.

    2013-01-01

    This map shows the spatial distribution of selected carbonates, phyllosilicates, sulfates, altered minerals, and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. The map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Epidote or chlorite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  19. Hyperspectral surface materials map of quadrangle 3364, Pasaband (417) and Markaz-e Kajiran (418) quadrangles, Afghanistan, showing carbonates, phyllosilicates, sulfates, altered minerals, and other materials

    Science.gov (United States)

    Kokaly, Raymond F.; King, Trude V.V.; Hoefen, Todd M.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

    2013-01-01

    This map shows the spatial distribution of selected carbonates, phyllosilicates, sulfates, altered minerals, and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. The map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Epidote or chlorite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  20. Hyperspectral Surface Materials Map of Quadrangle 3566, Sangcharak (501) and Sayghan-o-Kamard (502) Quadrangles, Afghanistan, Showing Carbonates, Phyllosilicates, Sulfates, Altered Minerals, and Other Materials

    Science.gov (United States)

    Kokaly, Raymond F.; King, Trude V.V.; Hoefen, Todd M.; Livo, Keith E.; Giles, Stuart A.; Johnson, Michaela R.

    2013-01-01

    This map shows the spatial distribution of selected carbonates, phyllosilicates, sulfates, altered minerals, and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. The map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Epidote or chlorite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  1. Hyperspectral surface materials map of quadrangle 3166, Jaldak (701) and Maruf-Nawa (702) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

    Science.gov (United States)

    King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Giles, Stuart A.; Johnson, Michaela R.

    2013-01-01

    This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  2. Hyperspectral surface materials map of quadrangle 3162, Chakhansur (603) and Kotalak (604) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

    Science.gov (United States)

    King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

    2013-01-01

    This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  3. Hyperspectral surface materials map of quadrangle 3264, Naw Zad-Musa Qala (423) and Dihrawud (424) quadrangles, Afghanistan, showing carbonates, phyllosilicates, sulfates, altered minerals, and other materials

    Science.gov (United States)

    Kokaly, Raymond F.; King, Trude V.V.; Hoefen, Todd M.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

    2013-01-01

    This map shows the spatial distribution of selected carbonates, phyllosilicates, sulfates, altered minerals, and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. The map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Epidote or chlorite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  4. Hyperspectral surface materials map of quadrangle 3362, Shindand (415) and Tulak (416) quadrangles, Afghanistan, showing carbonates, phyllosilicates, sulfates, altered minerals, and other materials

    Science.gov (United States)

    Kokaly, Raymond F.; King, Trude V.V.; Hoefen, Todd M.; Livo, Keith E.; Giles, Stuart A.; Johnson, Michaela R.

    2013-01-01

    This map shows the spatial distribution of selected carbonates, phyllosilicates, sulfates, altered minerals, and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. The map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Epidote or chlorite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  5. Hyperspectral surface materials map of quadrangle 3462, Herat (409) and Chishti Sharif (410) quadrangles, Afghanistan, showing carbonates, phyllosilicates, sulfates, altered minerals, and other materials

    Science.gov (United States)

    Kokaly, Raymond F.; King, Trude V.V.; Hoefen, Todd M.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

    2013-01-01

    This map shows the spatial distribution of selected carbonates, phyllosilicates, sulfates, altered minerals, and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. The map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Epidote or chlorite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  6. Hyperspectral surface materials map of quadrangle 3368, Ghazni (515) and Gardez (516) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

    Science.gov (United States)

    King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

    2013-01-01

    This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  7. Hyperspectral surface materials map of quadrangle 3670, Jurm-Kishim (223) and Zebak (224) quadrangles, Afghanistan, showing iron-bearing minerals and other materials

    Science.gov (United States)

    King, Trude V.V.; Hoefen, Todd M.; Kokaly, Raymond F.; Livo, Keith E.; Johnson, Michaela R.; Giles, Stuart A.

    2013-01-01

    This map shows the spatial distribution of selected iron-bearing minerals and other materials derived from analysis of airborne HyMap™ imaging spectrometer (hyperspectral) data of Afghanistan collected in late 2007. This map is one in a series of U.S. Geological Survey/Afghanistan Geological Survey quadrangle maps covering Afghanistan. Flown at an altitude of 50,000 feet (15,240 meters (m)), the HyMap™ imaging spectrometer measured reflected sunlight in 128 channels, covering wavelengths between 0.4 and 2.5 μm. The data were georeferenced, atmospherically corrected and converted to apparent surface reflectance, empirically adjusted using ground-based reflectance measurements, and combined into a mosaic with 23-m pixel spacing. Variations in water vapor and dust content of the atmosphere, in solar angle, and in surface elevation complicated correction; therefore, some classification differences may be present between adjacent flight lines. The reflectance spectrum of each pixel of HyMap™ imaging spectrometer data was compared to the reference materials in a spectral library of minerals, vegetation, water, and other materials. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated, while minerals having slightly different compositions but similar spectral features were less easily discriminated; thus, some map classes consist of several minerals having similar spectra, such as “Goethite and jarosite.” A designation of “Not classified” was assigned to the pixel when there was no match with reference spectra.

  8. The invasive species Ulex europaeus (Fabaceae) shows high dynamism in a fragmented landscape of south-central Chile.

    Science.gov (United States)

    Altamirano, Adison; Cely, Jenny Paola; Etter, Andrés; Miranda, Alejandro; Fuentes-Ramirez, Andres; Acevedo, Patricio; Salas, Christian; Vargas, Rodrigo

    2016-08-01

    Ulex europaeus (gorse) is an invasive shrub deemed as one of the most invasive species in the world. U. europaeus is widely distributed in the south-central area of Chile, which is considered a world hotspot for biodiversity conservation. In addition to its negative effects on the biodiversity of natural ecosystems, U. europaeus is one of the most severe pests for agriculture and forestry. Despite its importance as an invasive species, U. europaeus has been little studied. Although information exists on the potential distribution of the species, the interaction of the invasion process with the spatial dynamic of the landscape and the landscape-scale factors that control the presence or absence of the species is still lacking. We studied the spatial and temporal dynamics of the landscape and how these relate to U. europaeus invasion in south-central Chile. We used supervised classification of satellite images to determine the spatial distribution of the species and other land covers for the years 1986 and 2003, analysing the transitions between the different land covers. We used logistic regression for modelling the increase, decrease and permanence of U. europaeus invasion considering landscape variables. Results showed that the species covers only around 1 % of the study area and showed a 42 % reduction in area for the studied period. However, U. europaeus was the cover type which presented the greatest dynamism in the landscape. We found a strong relationship between changes in land cover and the invasion process, especially connected with forest plantations of exotic species, which promotes the displacement of U. europaeus. The model of gorse cover increase presented the best performance, and the most important predictors were distance to seed source and landscape complexity index. Our model predicted high spread potential of U. europaeus in areas of high conservation value. We conclude that proper management for this invasive species must take into account

  9. A defined terminal region of the E. coli chromosome shows late segregation and high FtsK activity.

    Directory of Open Access Journals (Sweden)

    Marie Deghorain

    Full Text Available BACKGROUND: The FtsK DNA-translocase controls the last steps of chromosome segregation in E. coli. It translocates sister chromosomes using the KOPS DNA motifs to orient its activity, and controls the resolution of dimeric forms of sister chromosomes by XerCD-mediated recombination at the dif site and their decatenation by TopoIV. METHODOLOGY: We have used XerCD/dif recombination as a genetic trap to probe the interaction of FtsK with loci located in different regions of the chromosome. This assay revealed that the activity of FtsK is restricted to a ∼400 kb terminal region of the chromosome around the natural position of the dif site. Preferential interaction with this region required the tethering of FtsK to the division septum via its N-terminal domain as well as its translocation activity. However, the KOPS-recognition activity of FtsK was not required. Displacement of replication termination outside the FtsK high activity region had no effect on FtsK activity and deletion of a part of this region was not compensated by its extension to neighbouring regions. By observing the fate of fluorescent-tagged loci of the ter region, we found that segregation of the FtsK high activity region is delayed compared to that of its adjacent regions. SIGNIFICANCE: Our results show that a restricted terminal region of the chromosome is specifically dedicated to the last steps of chromosome segregation and to their coupling with cell division by FtsK.

  10. An EGFR/HER2-Bispecific and enediyne-energized fusion protein shows high efficacy against esophageal cancer.

    Directory of Open Access Journals (Sweden)

    Xiao-Fang Guo

    Full Text Available Esophageal cancer is one of the most common cancers, and the 5-year survival rate is less than 10% due to lack of effective therapeutic agents. This study was to evaluate antitumor activity of Ec-LDP-Hr-AE, a recently developed bispecific enediyne-energized fusion protein targeting both epidermal growth factor receptor (EGFR and epidermal growth factor receptor 2 (HER2, on esophageal cancer. The fusion protein Ec-LDP-Hr-AE consists of two oligopeptide ligands and an enediyne antibiotic lidamycin (LDM for receptor binding and cell killing, respectively. The current study demonstrated that Ec-LDP-Hr had high affinity to bind to esophageal squamous cell carcinoma (ESCC cells, and enediyne-energized fusion protein Ec-LDP-Hr-AE showed potent cytotoxicity to ESCC cells with differential expression of EGFR and HER2. Ec-LDP-Hr-AE could cause significant G2-M arrest in EC9706 and KYSE150 cells, and it also induced apoptosis in ESCC cells in a dosage-dependent manner. Western blot assays showed that Ec-LDP-Hr-AE promoted caspase-3 and caspase-7 activities as well as PARP cleavage. Moreover, Ec-LDP-Hr-AE inhibited cell proliferation via decreasing phosphorylation of EGFR and HER2, and further exerted inhibition of the activation of their downstream signaling molecules. In vivo, at a tolerated dose, Ec-LDP-Hr-AE inhibited tumor growth by 88% when it was administered to nude mice bearing human ESCC cell KYSE150 xenografts. These results indicated that Ec-LDP-Hr-AE exhibited potent anti-caner efficacy on ESCC, suggesting it could be a promising candidate for targeted therapy of esophageal cancer.

  11. CD38 Knockout Mice Show Significant Protection Against Ischemic Brain Damage Despite High Level Poly-ADP-Ribosylation.

    Science.gov (United States)

    Long, Aaron; Park, Ji H; Klimova, Nina; Fowler, Carol; Loane, David J; Kristian, Tibor

    2017-01-01

    Several enzymes in cellular bioenergetics metabolism require NAD(+) as an essential cofactor for their activity. NAD(+) depletion following ischemic insult can result in cell death and has been associated with over-activation of poly-ADP-ribose polymerase PARP1 as well as an increase in NAD(+) consuming enzyme CD38. CD38 is an NAD(+) glycohydrolase that plays an important role in inflammatory responses. To determine the contribution of CD38 activity to the mechanisms of post-ischemic brain damage we subjected CD38 knockout (CD38KO) mice and wild-type (WT) mice to transient forebrain ischemia. The CD38KO mice showed a significant amelioration in both histological and neurologic outcome following ischemic insult. Decrease of hippocampal NAD(+) levels detected during reperfusion in WT mice was only transient in CD38KO animals, suggesting that CD38 contributes to post-ischemic NAD(+) catabolism. Surprisingly, pre-ischemic poly-ADP-ribose (PAR) levels were dramatically higher in CD38KO animals compared to WT animals and exhibited reduction post-ischemia in contrast to the increased levels in WT animals. The high PAR levels in CD38 mice were due to reduced expression levels of poly-ADP-ribose glycohydrolase (PARG). Thus, the absence of CD38 activity can not only directly affect inflammatory response, but also result in unpredicted alterations in the expression levels of enzymes participating in NAD(+) metabolism. Although the CD38KO mice showed significant protection against ischemic brain injury, the changes in enzyme activity related to NAD(+) metabolism makes the determination of the role of CD38 in mechanisms of ischemic brain damage more complex.

  12. Antifouling property of highly oleophobic substrates for solar cell surfaces

    Science.gov (United States)

    Fukada, Kenta; Nishizawa, Shingo; Shiratori, Seimei

    2014-03-01

    Reduction of solar cell conversion efficiency by bird spoor or oil smoke is a common issue. Maintaining the surface of solar cells clean to retain the incident light is of utmost importance. In this respect, there has been growing interest in the area of superhydrophobicity for developing water repelling and self-cleaning surfaces. This effect is inspired by lotus leaves that have micro papillae covered with hydrophobic wax nanostructures. Superhydrophobic surfaces on transparent substrates have been developed for removing contaminants from solar cell surfaces. However, oil cannot be removed by superhydrophobic effect. In contrast, to prevent bird spoor, a highly oleophobic surface is required. In a previous study, we reported transparent-type fabrics comprising nanoparticles with a nano/micro hierarchical structure that ensured both oleophobicity and transparency. In the current study, we developed new highly oleophobic stripes that were constructed into semi-transparent oleophobic surfaces for solar cells. Solar cell performance was successfully maintained; the total transmittance was a key factor for determining conversion efficiency.

  13. High Efficiency, High Temperature Foam Core Heat Exchanger for Fission Surface Power Systems, Phase II Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Fission-based power systems with power levels of 30 to ≥100 kWe will be needed for planetary surface bases. Development of high temperature, high efficiency...

  14. Analysis of a large dataset of mycorrhiza inoculation field trials on potato shows highly significant increases in yield.

    Science.gov (United States)

    Hijri, Mohamed

    2016-04-01

    An increasing human population requires more food production in nutrient-efficient systems in order to simultaneously meet global food needs while reducing the environmental footprint of agriculture. Arbuscular mycorrhizal fungi (AMF) have the potential to enhance crop yield, but their efficiency has yet to be demonstrated in large-scale crop production systems. This study reports an analysis of a dataset consisting of 231 field trials in which the same AMF inoculant (Rhizophagus irregularis DAOM 197198) was applied to potato over a 4-year period in North America and Europe under authentic field conditions. The inoculation was performed using a liquid suspension of AMF spores that was sprayed onto potato seed pieces, yielding a calculated 71 spores per seed piece. Statistical analysis showed a highly significant increase in marketable potato yield (ANOVA, P < 0.0001) for inoculated fields (42.2 tons/ha) compared with non-inoculated controls (38.3 tons/ha), irrespective of trial year. The average yield increase was 3.9 tons/ha, representing 9.5 % of total crop yield. Inoculation was profitable with a 0.67-tons/ha increase in yield, a threshold reached in almost 79 % of all trials. This finding clearly demonstrates the benefits of mycorrhizal-based inoculation on crop yield, using potato as a case study. Further improvements of these beneficial inoculants will help compensate for crop production deficits, both now and in the future.

  15. Activity/inactivity circadian rhythm shows high similarities between young obesity-induced rats and old rats.

    Science.gov (United States)

    Bravo Santos, R; Delgado, J; Cubero, J; Franco, L; Ruiz-Moyano, S; Mesa, M; Rodríguez, A B; Uguz, C; Barriga, C

    2016-03-01

    The objective of the present study was to compare differences between elderly rats and young obesity-induced rats in their activity/inactivity circadian rhythm. The investigation was motivated by the differences reported previously for the circadian rhythms of both obese and elderly humans (and other animals), and those of healthy, young or mature individuals. Three groups of rats were formed: a young control group which was fed a standard chow for rodents; a young obesity-induced group which was fed a high-fat diet for four months; and an elderly control group with rats aged 2.5 years that was fed a standard chow for rodents. Activity/inactivity data were registered through actimetry using infrared actimeter systems in each cage to detect activity. Data were logged on a computer and chronobiological analysis were performed. The results showed diurnal activity (sleep time), nocturnal activity (awake time), amplitude, acrophase, and interdaily stability to be similar between the young obesity-induced group and the elderly control group, but different in the young control group. We have concluded that obesity leads to a chronodisruption status in the body similar to the circadian rhythm degradation observed in the elderly.

  16. Tongue Epithelium Cells from shRNA Mediated Transgenic Goat Show High Resistance to Foot and Mouth Disease Virus.

    Science.gov (United States)

    Li, Wenting; Wang, Kejun; Kang, Shimeng; Deng, Shoulong; Han, Hongbing; Lian, Ling; Lian, Zhengxing

    2015-12-16

    Foot and mouth disease induced by foot and mouth disease virus (FMDV) is severe threat to cloven-hoofed domestic animals. The gene 3Dpol in FMDV genome encodes the viral RNA polymerase, a vital element for FMDV replication. In this study, a conserved 3D-7414shRNA targeting FMDV-3Dpol gene was designed and injected into pronuclear embryos to produce the transgenic goats. Sixty-one goats were produced, of which, seven goats positively integrated 3D-7414shRNA. Loss of function assay demonstrated that siRNA effectively knockdown 3Dpol gene in skin epithelium cells of transgenic goats. Subsequently, the tongue epithelium cells from transgenic and non-transgenic goats were infected with FMDV O/YS/CHA/05 strain. A significant decrease of virus titres and virus copy number was observed in cells of transgenic goats compared with that of non-transgenic goats, which indicated that 3D-7414siRNA inhibited FMDV replication by interfering FMDV-3Dpol gene. Furthermore, we found that expression of TLR7, RIG-I and TRAF6 was lower in FMDV infected cells from transgenic goats compared to that from non-transgenic goats, which might result from lower virus copy number in transgenic goats' cells. In conclusion, we successfully produced transgenic goats highly expressing 3D-7414siRNA targeting 3Dpol gene, and the tongue epithelium cells from the transgenic goats showed effective resistance to FMDV.

  17. Thermal Stability of Surface Layer Microstructures of Commercially Pure Titanium Treated by High Energy Shot Peening

    Institute of Scientific and Technical Information of China (English)

    ZHANG Yu-juan; CHEN Chun-huan; REN Rui-ming

    2004-01-01

    Commercially pure titanium was treated by high energy shot peening, and annealed at a series of temperatures. The surface layers are characterized by means of scan electronic microscope, X-Ray diffraction, transmission electronic microscope and micro-hardness testing machine. The results showed that microhardness of surface layers decreases with anneal temperature, the tendency of microhardness is similar to unannealed one, in other words, the more close to the surface, the more rapidly the hardness decreases, after reaches the depth of 50 μm, the decrease becomes steadily. But the sub-surface microhardness decreased suddenly over 500 ℃, From 550 ℃ to 650 ℃, the microhardness of surface layers almost unchanged.Observing by TEM and SEM, the grain sizes of pure titanium surface layers have increased below 500 ℃; Deformation twins begin disappearing obviously at 550 ℃; The nano-scaled grains within about 10 micrometers from surface existed even at 550℃.Surface nanocrystallization is well known as one of important methods to improve surface properties. The thermal stability of nanocrystalline microstructures was related to their preparation and application. The commercial pure Ti thermal stability of nanocrystalline and deformed microstructures induced by high-energy-shot-peening (HESP) technique was investigated. The nanostructured surface and deformed sub-surface layers of specimens were prepared through HESP treatment. The thermal stability was characterized through XRD analyses of surface layers, SEM and TEM microstructure observation and microhardness measurement of specimens annealed in different temperature in the air after HESP treatments. The results showed that after HESP treatment, the microhardness of surface layers increased with treatment time, especially in the rang of about 40 micrometers from the surface, the microhardness increase was obvious. The surface microhardness decreased gradually with annealing temperature, but the sub-surface

  18. Low and High Surface Brightness Galaxies at Void Walls

    CERN Document Server

    Ceccarelli, L; Lambas, D G; Galaz, G; Padilla, N D

    2012-01-01

    We study the relative fraction of low and high surface brightness galaxies (LSBGs and HSBGs) at void walls in the SDSS DR7. We focus on galaxies in equal local density environments. We assume that the host dark-matter halo mass (for which we use SDSS group masses) is a good indicator of local density. This analysis allows to examine the behavior of the abundance of LSBG and HSBG galaxies at a fixed local density and distinguish the large-scale environment defined by the void geometry. We compare galaxies in the field, and in the void walls; the latter are defined as the volume of void shells of radius equal to that of the void. We find a significant decrement, a factor $\\sim 4$, of the relative fraction of blue, active star-forming LSBGs in equal mass groups at the void walls and the field. This decrement is consistent with an increase of the fraction of blue, active star-forming HSBGs. By contrast, red LSBGs and HSBGs show negligible changes. We argue that these results are consistent with a scenario where L...

  19. X-ray characterization of surfaces irradiated with highly charged ions

    Energy Technology Data Exchange (ETDEWEB)

    Briand, J.P. [Laboratoire Kastler Brossel, Universite P. et M. Curie, Paris (France); Universite P. et M. Curie, Paris (France); Ion Surface Advanced Processes (ISAP) muE., 2 Square Francois Couperin, 92160 Antony (France)], E-mail: jpbriand920@aol.com; Benhachoum, M. [Universite P. et M. Curie, Paris (France)

    2009-02-15

    Highly charged ions (HCI) approaching, touching or penetrating dielectric surfaces extract many electrons of the solid leading to the formation of permanent surface modifications. The ions which capture the electrons in their outermost shells form hollow atoms which emit X-rays during their decay to the ground state. In this paper one presents experiments showing that these X-rays) allow diagnosing the electric nature of the surfaces. HCI while modifying the structure of surfaces may then also be used to diagnose these changes on line or off line.

  20. X-ray photoelectron spectroscopy of negative electrodes from high-power lithium-ion cells showing various levels of power fade

    Energy Technology Data Exchange (ETDEWEB)

    Herstedt, Marie; Abraham, Daniel P.; Kerr, John B.

    2004-02-28

    High-power lithium-ion cells for transportation applications are being developed and studied at Argonne National Laboratory. The current generation of cells containing LiNi{sub 0.8}Co{sub 0.15}Al{sub 0.05}O{sub 2}-based cathodes, graphite-based anodes, and LiPF6-based electrolytes show loss of capacity and power during accelerated testing at elevated temperatures. Negative electrode samples harvested from some cells that showed varying degrees of power and capacity fade were examined by X-ray photoelectron spectroscopy (XPS). The samples exhibited a surface film on the graphite, which was thicker on samples from cells that showed higher fade. Furthermore, solvent-based compounds were dominant on samples from low power fade cells, whereas LiPF{sub 6}-based products were dominant on samples from high power fade cells. The effect of sample rinsing and air exposure is discussed. Mechanisms are proposed to explain the formation of compounds suggested by the XPS data.

  1. Plasma Levels of Macrophage Migration Inhibitory Factor and d-Dopachrome Tautomerase Show a Highly Specific Profile in Early Life

    Science.gov (United States)

    Roger, Thierry; Schlapbach, Luregn J.; Schneider, Anina; Weier, Manuela; Wellmann, Sven; Marquis, Patrick; Vermijlen, David; Sweep, Fred C. G. J.; Leng, Lin; Bucala, Richard; Calandra, Thierry; Giannoni, Eric

    2017-01-01

    Macrophage migration inhibitory factor (MIF) is a pleiotropic, constitutively expressed, pro-inflammatory cytokine and an important regulator of immune responses. d-dopachrome tautomerase (DDT), a newly described member of the MIF protein superfamily, shares sequence homology and biological activities with MIF. We recently reported that high expression levels of MIF sustain innate immune responses in newborns. Here, we elected to further characterize age-dependent MIF expression and to define whether DDT shares a similar expression profile with MIF. Therefore, we delineated the circulating concentrations of MIF and DDT throughout life using a large cohort of 307 subjects including fetuses, newborns, infants, children, and adults. Compared to levels measured in healthy adults (median: 5.7 ng/ml for MIF and 16.8 ng/ml for DDT), MIF and DDT plasma concentrations were higher in fetuses (median: 48.9 and 29.6 ng/ml), increased further at birth (median: 82.6 and 52.0 ng/ml), reached strikingly elevated levels on postnatal day 4 (median: 109.5 and 121.6 ng/ml), and decreased to adult levels during the first months of life. A strong correlation was observed between MIF and DDT concentrations in all age groups (R = 0.91, P < 0.0001). MIF and DDT levels correlated with concentrations of vascular endothelial growth factor, a protein upregulated under low oxygen tension and implicated in vascular and lung development (R = 0.70, P < 0.0001 for MIF and R = 0.65, P < 0.0001 for DDT). In very preterm infants, lower levels of MIF and DDT on postnatal day 6 were associated with an increased risk of developing bronchopulmonary dysplasia and late-onset neonatal sepsis. Thus, MIF and DDT plasma levels show a highly specific developmental profile in early life, supporting an important role for these cytokines during the neonatal period. PMID:28179905

  2. Design methodology to enhance high impedance surfaces performances

    Directory of Open Access Journals (Sweden)

    M. Grelier

    2014-04-01

    Full Text Available A methodology is introduced for designing wideband, compact and ultra-thin high impedance surfaces (HIS. A parametric study is carried out to examine the effect of the periodicity on the electromagnetic properties of an HIS. This approach allows designers to reach the best trade-off for HIS performances.

  3. Collisions of Slow Highly Charged Ions with Surfaces

    OpenAIRE

    Burgdoerfer, J.; Lemell, C.; Schiessl, K.; Solleder, B.; Reinhold, C; Tokesi, K.; Wirtz, Ludger

    2006-01-01

    Progress in the study of collisions of multiply charged ions with surfaces is reviewed with the help of a few recent examples. They range from fundamental quasi-one electron processes to highly complex ablation and material modification processes. Open questions and possible future directions will be discussed.

  4. Highly antibacterial UHMWPE surfaces by implantation of titanium ions

    Energy Technology Data Exchange (ETDEWEB)

    Delle Side, D., E-mail: domenico.delleside@le.infn.it [LEAS, Dipartimento di Matematica e Fisica “Ennio de Giorgi”, Università del Salento, Lecce (Italy); Istituto Nazionale di Fisica Nucleare – Sezione di Lecce, Lecce (Italy); Nassisi, V.; Giuffreda, E.; Velardi, L. [LEAS, Dipartimento di Matematica e Fisica “Ennio de Giorgi”, Università del Salento, Lecce (Italy); Istituto Nazionale di Fisica Nucleare – Sezione di Lecce, Lecce (Italy); Alifano, P.; Talà, A.; Tredici, S.M. [Dipartimento di Scienze e Tecnologie Biologiche ed Ambientali, Università del Salento, Lecce (Italy)

    2014-07-15

    The spreading of pathogens represents a serious threat for human beings. Consequently, efficient antimicrobial surfaces are needed in order to reduce risks of contracting severe diseases. In this work we present the first evidences of a new technique to obtain a highly antibacterial Ultra High Molecular Weight Polyethylene (UHMWPE) based on a non-stoichiometric titanium oxide coating, visible-light responsive, obtained through ion implantation.

  5. Highly Sensitive Local Surface Plasmon Resonance in Anisotropic Au Nanoparticles Deposited on Nanofibers

    Directory of Open Access Journals (Sweden)

    Masanari Saigusa

    2015-01-01

    Full Text Available This paper reports the facile and high-throughput fabrication method of anisotropic Au nanoparticles with a highly sensitive local surface plasmon resonance (LPR using cylindrical nanofibers as substrates. The substrates consisting of nanofibers were prepared by the electrospinning of poly(vinylidene fluoride (PVDF. The Au nanoparticles were deposited on the surface of electrospun nanofibers by vacuum evaporation. Scanning electron microscopy revealed the formation of a curved Au island structure on the surface of cylindrical nanofibers. Polarized UV-visible extinction spectroscopy showed anisotropy in their LPR arising from the high surface curvature of the nanofiber. The LPR of the Au nanoparticles on the thinnest nanofiber with a diameter of ~100 nm showed maximum refractive index (RI sensitivity over 500 nm/RI unit (RIU. The close correlation between the fiber diameter dependence of the RI sensitivity and polarization dependence of the LPR suggests that anisotropic Au nanoparticles improve RI sensitivity.

  6. Newcastle Disease Viruses Causing Recent Outbreaks Worldwide Show Unexpectedly High Genetic Similarity to Historical Virulent Isolates from the 1940s.

    Science.gov (United States)

    Dimitrov, Kiril M; Lee, Dong-Hun; Williams-Coplin, Dawn; Olivier, Timothy L; Miller, Patti J; Afonso, Claudio L

    2016-05-01

    Virulent strains of Newcastle disease virus (NDV) cause Newcastle disease (ND), a devastating disease of poultry and wild birds. Phylogenetic analyses clearly distinguish historical isolates (obtained prior to 1960) from currently circulating viruses of class II genotypes V, VI, VII, and XII through XVIII. Here, partial and complete genomic sequences of recent virulent isolates of genotypes II and IX from China, Egypt, and India were found to be nearly identical to those of historical viruses isolated in the 1940s. Phylogenetic analysis, nucleotide distances, and rates of change demonstrate that these recent isolates have not evolved significantly from the most closely related ancestors from the 1940s. The low rates of change for these virulent viruses (7.05 × 10(-5) and 2.05 × 10(-5) per year, respectively) and the minimal genetic distances existing between these and historical viruses (0.3 to 1.2%) of the same genotypes indicate an unnatural origin. As with any other RNA virus, Newcastle disease virus is expected to evolve naturally; thus, these findings suggest that some recent field isolates should be excluded from evolutionary studies. Furthermore, phylogenetic analyses show that these recent virulent isolates are more closely related to virulent strains isolated during the 1940s, which have been and continue to be used in laboratory and experimental challenge studies. Since the preservation of viable viruses in the environment for over 6 decades is highly unlikely, it is possible that the source of some of the recent virulent viruses isolated from poultry and wild birds might be laboratory viruses. Copyright © 2016, American Society for Microbiology. All Rights Reserved.

  7. Effect of high rotor pressure-surface diffusion on performance of a transonic turbine

    Science.gov (United States)

    Miser, James W; Stewart, Warner L; Monroe, Daniel E

    1955-01-01

    The subject turbine was investigated to determine the effect of high rotor pressure-surface diffusion on turbine performance. A comparison of the subject turbine with the most efficient transonic turbine in the present series of investigations showed that the efficiency of the subject turbine was almost as high, the suction-surface diffusion parameter was about the same, and the solidity was reduced by 36 percent. Because the loss per blade increased greatly with an increase in pressure-surface diffusion, the latter is also considered to be an important design consideration.

  8. Surface modifications induced by high fluxes of low energy helium ions.

    Science.gov (United States)

    Tanyeli, İrem; Marot, Laurent; Mathys, Daniel; van de Sanden, Mauritius C M; De Temmerman, Gregory

    2015-04-28

    Several metal surfaces, such as titanium, aluminum and copper, were exposed to high fluxes (in the range of 10(23) m(-2) s(-1)) of low energy (pillars, are observed on these metals. The differences and similarities in the development of surface morphologies are discussed in terms of the material properties and compared with the results of similar experimental studies. The results show that He ions induced void growth and physical sputtering play a significant role in surface modification using high fluxes of low energy He ions.

  9. Surface Intermediates on Metal Electrodes at High Temperature

    DEFF Research Database (Denmark)

    Zachau-Christiansen, Birgit; Jacobsen, Torben; Bay, Lasse

    1997-01-01

    The mechanisms widely suggested for the O2-reduc-tion or H2-oxidation SOFC reactions involve inter-mediate O/H species adsorbed on the electrode surface. The presence of these intermediates is investigated by linear sweep voltammetry. In airat moderate temperatures (500øC) Pt in contact with YSZ ...... is covered with adsorbed oxygen which vanishes at high temperature (1000øC). On Ni (YSZ) a specific layer of NiO is observed abovethe equilibrium potential while no surface species can identified at SOFC anode conditions....

  10. Surface intermediates on metal electrodes at high temperatures

    DEFF Research Database (Denmark)

    Zachau-Christiansen, Birgit; Jacobsen, Torben; Bay, Lasse;

    1998-01-01

    in contact with YSZ is covered with adsorbed oxygen which vanishes at high temperature (1000 degrees C). On Ni (YSZ) a specific layer of NiO is observed above the equilibrium potential while no surface species involving hydrogen can be identified at SOFC anode conditions. (C) 1998 Published by Elsevier......The mechanisms widely conceived for the O(2)-reduction or H(2)-oxidation reactions in SOFC's involve intermediate O/H species adsorbed on the electrode surface. The presence of these intermediates is investigated by linear sweep voltammetry. In air at moderate temperatures (500 degrees C) Pt...

  11. High surface area carbon and process for its production

    Energy Technology Data Exchange (ETDEWEB)

    Romanos, Jimmy; Burress, Jacob; Pfeifer, Peter; Rash, Tyler; Shah, Parag; Suppes, Galen

    2016-12-13

    Activated carbon materials and methods of producing and using activated carbon materials are provided. In particular, biomass-derived activated carbon materials and processes of producing the activated carbon materials with prespecified surface areas and pore size distributions are provided. Activated carbon materials with preselected high specific surface areas, porosities, sub-nm (<1 nm) pore volumes, and supra-nm (1-5 nm) pore volumes may be achieved by controlling the degree of carbon consumption and metallic potassium intercalation into the carbon lattice during the activation process.

  12. Weissenberg reflection high-energy electron diffraction for surface crystallography.

    Science.gov (United States)

    Abukawa, Tadashi; Yamazaki, Tomoyuki; Yajima, Kentaro; Yoshimura, Koji

    2006-12-15

    The principle of a Weissenberg camera is applied to surface crystallographic analysis by reflection high-energy electron diffraction. By removing inelastic electrons and measuring hundreds of patterns as a function of sample rotation angle phi, kinematical analysis can be performed over a large volume of reciprocal space. The data set is equivalent to a three-dimensional stack of Weissenberg photographs. The method is applied to analysis of an Si(111)-square root of 3 x square root of 3-Ag surface, and the structural data obtained are in excellent agreement with the known atomic structure.

  13. Modelling surface restructuring by slow highly charged ions

    Science.gov (United States)

    Wachter, G.; Tőkési, K.; Betz, G.; Lemell, C.; Burgdörfer, J.

    2013-12-01

    We theoretically investigate surface modifications on alkaline earth halides due to highly charged ion impact, focusing on recent experimental evidence for both etch pit and nano-hillock formation on CaF2 (A.S. El-Said et al., Phys. Rev. Lett. 109, (2012) 117602 [1]). We discuss mechanisms for converting the projectile potential and kinetic energies into thermal energy capable of changing the surface structure. A proof-of-principle classical molecular dynamics simulation suggests the existence of two thresholds which we associate with etch pit and nano-hillock formation in qualitative agreement with experiment.

  14. Modelling surface restructuring by slow highly charged ions

    Energy Technology Data Exchange (ETDEWEB)

    Wachter, G., E-mail: georg.wachter@tuwien.ac.at [Institute for Theoretical Physics, Vienna University of Technology, Wiedner Hauptstraße 8-10, A-1040 Vienna (Austria); Tőkési, K. [Institute of Nuclear Research of the Hungarian Academy of Science (ATOMKI), H-4001 Debrecen, P.O. Box 51 (Hungary); Betz, G. [Institute for Applied Physics, Vienna University of Technology, Wiedner Hauptstraße 8-10, A-1040 Vienna (Austria); Lemell, C.; Burgdörfer, J. [Institute for Theoretical Physics, Vienna University of Technology, Wiedner Hauptstraße 8-10, A-1040 Vienna (Austria)

    2013-12-15

    We theoretically investigate surface modifications on alkaline earth halides due to highly charged ion impact, focusing on recent experimental evidence for both etch pit and nano-hillock formation on CaF{sub 2} (A.S. El-Said et al., Phys. Rev. Lett. 109, (2012) 117602 [1]). We discuss mechanisms for converting the projectile potential and kinetic energies into thermal energy capable of changing the surface structure. A proof-of-principle classical molecular dynamics simulation suggests the existence of two thresholds which we associate with etch pit and nano-hillock formation in qualitative agreement with experiment.

  15. Preparation of Zirconia-Ceria Powders with High Specific Surface Area

    Institute of Scientific and Technical Information of China (English)

    Wang Enguo; Mei Fang

    2004-01-01

    Zirconia-ceria mixed oxide powders were prepared by high temperature aging method.The effects of the temperature and the time of aging, cerium content and calcination on powder performance were studied.The result shows that high temperature aging is an efficient way of preparation of ZrO2-CeO2 mixed oxide powders with high specific surface area and good thermal stability, and that addition of a small amount of cerium to hydrous zirconia can promote the preparation of high specific surface area powders.

  16. High resolution surface plasmon microscopy for cell imaging

    Science.gov (United States)

    Argoul, F.; Monier, K.; Roland, T.; Elezgaray, J.; Berguiga, L.

    2010-04-01

    We introduce a new non-labeling high resolution microscopy method for cellular imaging. This method called SSPM (Scanning Surface Plasmon Microscopy) pushes down the resolution limit of surface plasmon resonance imaging (SPRi) to sub-micronic scales. High resolution SPRi is obtained by the surface plasmon lauching with a high numerical aperture objective lens. The advantages of SPPM compared to other high resolution SPRi's rely on three aspects; (i) the interferometric detection of the back reflected light after plasmon excitation, (ii) the twodimensional scanning of the sample for image reconstruction, (iii) the radial polarization of light, enhancing both resolution and sensitivity. This microscope can afford a lateral resolution of - 150 nm in liquid environment and - 200 nm in air. We present in this paper images of IMR90 fibroblasts obtained with SSPM in dried environment. Internal compartments such as nucleus, nucleolus, mitochondria, cellular and nuclear membrane can be recognized without labelling. We propose an interpretation of the ability of SSPM to reveal high index contrast zones by a local decomposition of the V (Z) function describing the response of the SSPM.

  17. Operational high latitude surface irradiance products from polar orbiting satellites

    Science.gov (United States)

    Godøy, Øystein

    2016-12-01

    It remains a challenge to find an adequate approach for operational estimation of surface incoming short- and longwave irradiance at high latitudes using polar orbiting meteorological satellite data. In this presentation validation results at a number of North Atlantic and Arctic Ocean high latitude stations are presented and discussed. The validation results have revealed that although the method works well and normally fulfil the operational requirements, there is room for improvement. A number of issues that can improve the estimates at high latitudes have been identified. These improvements are partly related to improved cloud classification using satellite data and partly related to improved handling of multiple reflections over bright surfaces (snow and sea ice), especially in broken cloud conditions. Furthermore, the availability of validation sites over open ocean and sea ice is a challenge.

  18. High-frequency shear-horizontal surface acoustic wave sensor

    Science.gov (United States)

    Branch, Darren W

    2013-05-07

    A Love wave sensor uses a single-phase unidirectional interdigital transducer (IDT) on a piezoelectric substrate for leaky surface acoustic wave generation. The IDT design minimizes propagation losses, bulk wave interferences, provides a highly linear phase response, and eliminates the need for impedance matching. As an example, a high frequency (.about.300-400 MHz) surface acoustic wave (SAW) transducer enables efficient excitation of shear-horizontal waves on 36.degree. Y-cut lithium tantalate (LTO) giving a highly linear phase response (2.8.degree. P-P). The sensor has the ability to detect at the pg/mm.sup.2 level and can perform multi-analyte detection in real-time. The sensor can be used for rapid autonomous detection of pathogenic microorganisms and bioagents by field deployable platforms.

  19. High surface area graphene foams by chemical vapor deposition

    Science.gov (United States)

    Drieschner, Simon; Weber, Michael; Wohlketzetter, Jörg; Vieten, Josua; Makrygiannis, Evangelos; Blaschke, Benno M.; Morandi, Vittorio; Colombo, Luigi; Bonaccorso, Francesco; Garrido, Jose A.

    2016-12-01

    Three-dimensional (3D) graphene-based structures combine the unique physical properties of graphene with the opportunity to get high electrochemically available surface area per unit of geometric surface area. Several preparation techniques have been reported to fabricate 3D graphene-based macroscopic structures for energy storage applications such as supercapacitors. Although reaserch has been focused so far on achieving either high specific capacitance or high volumetric capacitance, much less attention has been dedicated to obtain high specific and high volumetric capacitance simultaneously. Here, we present a facile technique to fabricate graphene foams (GF) of high crystal quality with tunable pore size grown by chemical vapor deposition. We exploited porous sacrificial templates prepared by sintering nickel and copper metal powders. Tuning the particle size of the metal powders and the growth temperature allow fine control of the resulting pore size of the 3D graphene-based structures smaller than 1 μm. The as-produced 3D graphene structures provide a high volumetric electric double layer capacitance (165 mF cm-3). High specific capacitance (100 Fg-1) is obtained by lowering the number of layers down to single layer graphene. Furthermore, the small pore size increases the stability of these GFs in contrast to the ones that have been grown so far on commercial metal foams. Electrodes based on the as-prepared GFs can be a boost for the development of supercapacitors, where both low volume and mass are required.

  20. High throughput RNA sequencing of a hybrid maize and its parents shows different mechanisms responsive to nitrogen limitation.

    Science.gov (United States)

    Bi, Yong-Mei; Meyer, Ann; Downs, Gregory S; Shi, Xuejiang; El-Kereamy, Ashraf; Lukens, Lewis; Rothstein, Steven J

    2014-01-28

    Development of crop varieties with high nitrogen use efficiency (NUE) is crucial for minimizing N loss, reducing environmental pollution and decreasing input cost. Maize is one of the most important crops cultivated worldwide and its productivity is closely linked to the amount of fertilizer used. A survey of the transcriptomes of shoot and root tissues of a maize hybrid line and its two parental inbred lines grown under sufficient and limiting N conditions by mRNA-Seq has been conducted to have a better understanding of how different maize genotypes respond to N limitation. A different set of genes were found to be N-responsive in the three genotypes. Many biological processes important for N metabolism such as the cellular nitrogen compound metabolic process and the cellular amino acid metabolic process were enriched in the N-responsive gene list from the hybrid shoots but not from the parental lines' shoots. Coupled to this, sugar, carbohydrate, monosaccharide, glucose, and sorbitol transport pathways were all up-regulated in the hybrid, but not in the parents under N limitation. Expression patterns also differed between shoots and roots, such as the up-regulation of the cytokinin degradation pathway in the shoots of the hybrid and down-regulation of that pathway in the roots. The change of gene expression under N limitation in the hybrid resembled the parent with the higher NUE trait. The transcript abundances of alleles derived from each parent were estimated using polymorphic sites in mapped reads in the hybrid. While there were allele abundance differences, there was no correlation between these and the expression differences seen between the hybrid and the two parents. Gene expression in two parental inbreds and the corresponding hybrid line in response to N limitation was surveyed using the mRNA-Seq technology. The data showed that the three genotypes respond very differently to N-limiting conditions, and the hybrid clearly has a unique expression pattern

  1. Marangoni driven turbulence in high energy surface melting processes

    CERN Document Server

    Kidess, Anton; Righolt, Bernhard W; Kleijn, Chris R

    2016-01-01

    Experimental observations of high-energy surface melting processes, such as laser welding, have revealed unsteady, often violent, motion of the free surface of the melt pool. Surprisingly, no similar observations have been reported in numerical simulation studies of such flows. Moreover, the published simulation results fail to predict the post-solidification pool shape without adapting non-physical values for input parameters, suggesting the neglect of significant physics in the models employed. The experimentally observed violent flow surface instabilities, scaling analyses for the occurrence of turbulence in Marangoni driven flows, and the fact that in simulations transport coefficients generally have to be increased by an order of magnitude to match experimentally observed pool shapes, suggest the common assumption of laminar flow in the pool may not hold, and that the flow is actually turbulent. Here, we use direct numerical simulations (DNS) to investigate the role of turbulence in laser melting of a st...

  2. Electron acceleration and high harmonic generation by relativistic surface plasmons

    Science.gov (United States)

    Cantono, Giada; Luca Fedeli Team; Andrea Sgattoni Team; Andrea Macchi Team; Tiberio Ceccotti Team

    2016-10-01

    Intense, short laser pulses with ultra-high contrast allow resonant surface plasmons (SPs) excitation on solid wavelength-scale grating targets, opening the way to the extension of Plasmonics in the relativistic regime and the manipulation of intense electromagnetic fields to develop new short, energetic, laser-synchronized radiation sources. Recent theoretical and experimental studies have explored the role of SP excitation in increasing the laser-target coupling and enhancing ion acceleration, high-order harmonic generation and surface electron acceleration. Here we present our results on SP driven electron acceleration from grating targets at ultra-high laser intensities (I = 5 ×1019 W/cm2, τ = 25 fs). When the resonant condition for SP excitation is fulfilled, electrons are emitted in a narrow cone along the target surface, with a total charge of about 100 pC and energy spectra peaked around 5 MeV. Distinguishing features of the resonant process were investigated by varying the incidence angle, grating type and with the support of 3D PIC simulations, which closely reproduced the experimental data. Open challenges and further measurements on high-order harmonic generation in presence of a relativistic SP will also be discussed.

  3. Surface tension of highly magnetized degenerate quark matter

    CERN Document Server

    Lugones, G

    2016-01-01

    We study the surface tension of highly magnetized three flavor quark matter within the formalism of multiple reflection expansion (MRE). Quark matter is described as a mixture of free Fermi gases composed by quarks $u$, $d$, $s$ and electrons, in chemical equilibrium under weak interactions. Due to the presence of strong magnetic fields the particles' transverse motion is quantized into Landau levels, and the surface tension has a different value in the parallel and transverse directions with respect to the magnetic field. We calculate the transverse and longitudinal surface tension for different values of the magnetic field and for quark matter drops with different sizes, from a few fm to the bulk limit. For baryon number densities between $2-10$ times the nuclear saturation density, the surface tension falls in the range $2 - 20$ MeV /fm$^{2}$. The largest contribution comes from strange quarks which have a surface tension an order of magnitude larger than the one for $u$ or $d$ quarks and more than two ord...

  4. Molecular dynamics simulation of functionalized graphene surface for high efficient loading of doxorubicin

    Science.gov (United States)

    Mirhosseini, Mohammad Masoud; Rahmati, Mahmoud; Zargarian, Seyed Shahrooz; Khordad, Reza

    2017-08-01

    Molecular dynamics simulations are performed to study the design and optimization of nanocarriers with high drug loading capacity. Functionalized graphene is considered as the nominated high capacity drug carrier and Dox as the drug model. The graphene surface functionalized with hydroxyl (- OH), carboxyl (- COOH), methyl (- CH3) and amine (- NH2) groups and their associated properties are investigated. The simulation results are illustrated that G - COOH surface absorbs Dox more effectively in comparison to other functionalized graphene surfaces due to the higher binding energy of carboxylic groups and the model drug. The effect of hydrogen bonding, temperature and surface porosity are also evaluated. The results show that binding energy and the solubility parameter are temperature-dependent. The simulation results in this present work reveal the underlying mechanisms of Dox loading on neat and functionalized graphene surfaces may be employed to design better graphene-based nanocarriers for the Dox delivery applications.

  5. A novel 5-enolpyruvylshikimate-3-phosphate synthase shows high glyphosate tolerance in Escherichia coli and tobacco plants

    National Research Council Canada - National Science Library

    Cao, Gaoyi; Liu, Yunjun; Zhang, Shengxue; Yang, Xuewen; Chen, Rongrong; Zhang, Yuwen; Lu, Wei; Liu, Yan; Wang, Jianhua; Lin, Min; Wang, Guoying

    2012-01-01

    ...) is the primary target of the broad-spectrum herbicide glyphosate. Identification of new aroA genes coding for EPSPS with a high level of glyphosate tolerance is essential for the development of glyphosate-tolerant crops...

  6. Preparation and Characterization of Porous Yttrium Oxide Powders with High Specific Surface Area

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    The porous cubic yttrium oxides with high specific surface area were prepared by the explosive decomposition of yttrium nitrate and its complex formed with methyl salicylate. The specific surface area and properties of powders synthesized at various temperatures were characterized using BET, X-ray diffraction (XRD), infrared spectra (IR), and scanning electron microscopy (SEM). The results indicate that the highest specific surface area is found to be 65.37 m2*g-1 at the calcination temperature of 600 ℃, and then decreases to 20.33 m2*g-1 with the calcination temperature rising from 600 to 900 ℃. The powders show strong surface activity for adsorping water and carbon dioxide in air, which also decreases with the rising calcination temperature. The drop both on the surface area and surface activity of samples at higher temperatures may be due to pore-narrowing(sintering) effects.

  7. Assimilation and High Resolution Forecasts of Surface and Near Surface Conditions for the 2010 Vancouver Winter Olympic and Paralympic Games

    Science.gov (United States)

    Bernier, Natacha B.; Bélair, Stéphane; Bilodeau, Bernard; Tong, Linying

    2014-01-01

    A dynamical model was experimentally implemented to provide high resolution forecasts at points of interests in the 2010 Vancouver Olympics and Paralympics Region. In a first experiment, GEM-Surf, the near surface and land surface modeling system, is driven by operational atmospheric forecasts and used to refine the surface forecasts according to local surface conditions such as elevation and vegetation type. In this simple form, temperature and snow depth forecasts are improved mainly as a result of the better representation of real elevation. In a second experiment, screen level observations and operational atmospheric forecasts are blended to drive a continuous cycle of near surface and land surface hindcasts. Hindcasts of the previous day conditions are then regarded as today's optimized initial conditions. Hence, in this experiment, given observations are available, observation driven hindcasts continuously ensure that daily forecasts are issued from improved initial conditions. GEM-Surf forecasts obtained from improved short-range hindcasts produced using these better conditions result in improved snow depth forecasts. In a third experiment, assimilation of snow depth data is applied to further optimize GEM-Surf's initial conditions, in addition to the use of blended observations and forecasts for forcing. Results show that snow depth and summer temperature forecasts are further improved by the addition of snow depth data assimilation.

  8. Quantification of optic disc edema during exposure to high altitude shows no correlation to acute mountain sickness.

    Directory of Open Access Journals (Sweden)

    Gabriel Willmann

    Full Text Available BACKGROUND: The study aimed to quantify changes of the optic nerve head (ONH during exposure to high altitude and to assess a correlation with acute mountain sickness (AMS. This work is related to the Tuebingen High Altitude Ophthalmology (THAO study. METHODOLOGY/PRINCIPAL FINDINGS: A confocal scanning laser ophthalmoscope (cSLO, Heidelberg Retina Tomograph, HRT3® was used to quantify changes at the ONH in 18 healthy participants before, during and after rapid ascent to high altitude (4559 m. Slitlamp biomicroscopy was used for clinical optic disc evaluation; AMS was assessed with Lake Louise (LL and AMS-cerebral (AMS-c scores; oxygen saturation (SpO₂ and heart rate (HR were monitored. These parameters were used to correlate with changes at the ONH. After the first night spent at high altitude, incidence of AMS was 55% and presence of clinical optic disc edema (ODE 79%. Key stereometric parameters of the HRT3® used to describe ODE (mean retinal nerve fiber layer [RNFL] thickness, RNFL cross sectional area, optic disc rim volume and maximum contour elevation changed significantly at high altitude compared to baseline (p<0.05 and were consistent with clinically described ODE. All changes were reversible in all participants after descent. There was no significant correlation between parameters of ODE and AMS, SpO₂ or HR. CONCLUSIONS/SIGNIFICANCE: Exposure to high altitude leads to reversible ODE in the majority of healthy subjects. However, these changes did not correlate with AMS or basic physiologic parameters such as SpO₂ and HR. For the first time, a quantitative approach has been used to assess these changes during acute, non-acclimatized high altitude exposure. In conclusion, ODE presents a reaction of the body to high altitude exposure unrelated to AMS.

  9. Quantification of Optic Disc Edema during Exposure to High Altitude Shows No Correlation to Acute Mountain Sickness

    Science.gov (United States)

    Willmann, Gabriel; Fischer, M. Dominik; Schatz, Andreas; Schommer, Kai; Messias, Andre; Zrenner, Eberhart; Bartz-Schmidt, Karl U.; Gekeler, Florian

    2011-01-01

    Background The study aimed to quantify changes of the optic nerve head (ONH) during exposure to high altitude and to assess a correlation with acute mountain sickness (AMS). This work is related to the Tuebingen High Altitude Ophthalmology (THAO) study. Methodology/Principal Findings A confocal scanning laser ophthalmoscope (cSLO, Heidelberg Retina Tomograph, HRT3®) was used to quantify changes at the ONH in 18 healthy participants before, during and after rapid ascent to high altitude (4559 m). Slitlamp biomicroscopy was used for clinical optic disc evaluation; AMS was assessed with Lake Louise (LL) and AMS-cerebral (AMS-c) scores; oxygen saturation (SpO2) and heart rate (HR) were monitored. These parameters were used to correlate with changes at the ONH. After the first night spent at high altitude, incidence of AMS was 55% and presence of clinical optic disc edema (ODE) 79%. Key stereometric parameters of the HRT3® used to describe ODE (mean retinal nerve fiber layer [RNFL] thickness, RNFL cross sectional area, optic disc rim volume and maximum contour elevation) changed significantly at high altitude compared to baseline (p<0.05) and were consistent with clinically described ODE. All changes were reversible in all participants after descent. There was no significant correlation between parameters of ODE and AMS, SpO2 or HR. Conclusions/Significance Exposure to high altitude leads to reversible ODE in the majority of healthy subjects. However, these changes did not correlate with AMS or basic physiologic parameters such as SpO2 and HR. For the first time, a quantitative approach has been used to assess these changes during acute, non-acclimatized high altitude exposure. In conclusion, ODE presents a reaction of the body to high altitude exposure unrelated to AMS. PMID:22069483

  10. Surface nanostructures in commercial pure Ti induced by high energy shot peening

    Institute of Scientific and Technical Information of China (English)

    CHEN Chun-huan; REN Rui-ming; ZHAO Xiu-juan; ZHANG Yu-jun

    2004-01-01

    The high-energy shot peening (HESP) technique was used to obtain the surface nanocrystalline microstructure for a hcp metal titanium. XRD, SEM and TEM were applied to characterize the microstructure of the surface layer. Large amount of the deformation twins in the surface layer were observed by SEM in the specimens after HESP treatment in a shot-time, and the number of deformation twins both in a single plane and in intersecting planes increases with HESP time, until the twin character disappears completely in the top surface layer, which means that the severe plastic deformation(SPD) occurs on the surface. The XRD analysis results show that after HESP treatmen for 30 - 60 min the surface grain size decreases to nanoscale. According to the TEM images and corresponding diffraction patterns from SPD areas of the 120 min-treatment specimen, the measured grain size near the surface is about 20 - 30 nm. The grain size in deformation layer increases with the depth from the surface, and the nanostructured layer is about 20 μm in depth. Therefore, the surface nanocrystalline and a gradient microstructure from the surface to the matrix are obtained, which results in the micro-hardness decreasing from surface to the matrix gradually.

  11. Surface morphology and deuterium retention in tungsten exposed to high flux D plasma at high temperatures

    NARCIS (Netherlands)

    Jia, Y. Z.; De Temmerman, G.; Luo, G. N.; Xu, H.Y.; Li, C.; Fu, B. Q.; Liu, W.

    2015-01-01

    Surface modifications and deuterium retention induced in tungsten by high fluxes (1024 m−2 s−1) low energy (38 eV) deuterium ions were studied as a function of surface temperature. Blister formation was studied by scanning electron microscopy and electron backscatter diffraction, while deuterium ret

  12. Surface nanodroplets for highly efficient liquid-liquid microextraction

    Science.gov (United States)

    Li, Miaosi; Lu, Ziyang; Yu, Haitao; Zhang, Xuehua

    2016-11-01

    Nanoscale droplets on a substrate are an essential element for a wide range of applications, such as laboratory-on-chip devices, simple and highly efficient miniaturized reactors for concentrating products, high-throughput single-bacteria or single-biomolecular analysis, encapsulation, and high-resolution imaging techniques. The solvent exchange process is a simple bottom-up approach for producing droplets at solid-liquid interfaces that are only several tens to hundreds of nanometers in height, or a few femtoliters in volume Oil nanodroplets can be produced on a substrate by solvent exchange in which a good solvent of oil is displaced by a poor solvent. Our previous work has significantly advanced understanding of the principle of solvent exchange, and the droplet size can be well-controlled by several parameters, including flow rates, flow geometry, gravitational effect and composition of solutions. In this work, we studied the microextraction effect of surface nanodroplets. Oil nanodroplets have been demonstrated to provide highly-efficient liquid-liquid microextraction of hydrophobic solute in a highly diluted solution. This effect proved the feasibility of nanodroplets as a platform for preconcentrating compounds for in situ highly sensitive microanalysis without further separation. Also the long lifetime and temporal stability of surface nanodroplets allow for some long-term extraction process and extraction without addition of stabilisers.

  13. Frequency selective surfaces based high performance microstrip antenna

    CERN Document Server

    Narayan, Shiv; Jha, Rakesh Mohan

    2016-01-01

    This book focuses on performance enhancement of printed antennas using frequency selective surfaces (FSS) technology. The growing demand of stealth technology in strategic areas requires high-performance low-RCS (radar cross section) antennas. Such requirements may be accomplished by incorporating FSS into the antenna structure either in its ground plane or as the superstrate, due to the filter characteristics of FSS structure. In view of this, a novel approach based on FSS technology is presented in this book to enhance the performance of printed antennas including out-of-band structural RCS reduction. In this endeavor, the EM design of microstrip patch antennas (MPA) loaded with FSS-based (i) high impedance surface (HIS) ground plane, and (ii) the superstrates are discussed in detail. The EM analysis of proposed FSS-based antenna structures have been carried out using transmission line analogy, in combination with the reciprocity theorem. Further, various types of novel FSS structures are considered in desi...

  14. High Efficiency, High Temperature Foam Core Heat Exchanger for Fission Surface Power Systems Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Fission-based power systems are anticipated for various planetary surface human base applications with power levels of 30?100+ kWe. The development of high...

  15. Characteristics of flame spread over the surface of charring solid combustibles at high altitude

    Institute of Scientific and Technical Information of China (English)

    LI Jie; JI Jie; ZHANG Ying; SUN JinHua

    2009-01-01

    To explore the characteristics of flame spread over the surface of charring solid combustibles at high altitude, the whitewood with uniform texture was chosen to conduct a series of experiments in Lhasa and Hefei, with altitude of 3658 m and 50 m respectively. Several parameters, including the flame height, flame spread rate, flame temperature, surface temperature, were measured on samples with different width and inclinations. A quantitative analysis of flame spread characteristics over sample surface at high altitude was performed. Results showed that, in the environment of lower pressure and oxygen concentration at high altitude, the flame height and flame spread rate over sample surface decreased, but the flame temperature increased slightly. However, with increasing of sample width, the relative difference between the flame spread rates at different altitudes decreased.

  16. Early childhood gut microbiomes show strong geographic differences among subjects at high risk for type 1 diabetes.

    Science.gov (United States)

    Kemppainen, Kaisa M; Ardissone, Alexandria N; Davis-Richardson, Austin G; Fagen, Jennie R; Gano, Kelsey A; León-Novelo, Luis G; Vehik, Kendra; Casella, George; Simell, Olli; Ziegler, Anette G; Rewers, Marian J; Lernmark, Åke; Hagopian, William; She, Jin-Xiong; Krischer, Jeffrey P; Akolkar, Beena; Schatz, Desmond A; Atkinson, Mark A; Triplett, Eric W

    2015-02-01

    Gut microbiome dysbiosis is associated with numerous diseases, including type 1 diabetes. This pilot study determines how geographical location affects the microbiome of infants at high risk for type 1 diabetes in a population of homogenous HLA class II genotypes. High-throughput 16S rRNA sequencing was performed on stool samples collected from 90 high-risk, nonautoimmune infants participating in The Environmental Determinants of Diabetes in the Young (TEDDY) study in the U.S., Germany, Sweden, and Finland. Study site-specific patterns of gut colonization share characteristics across continents. Finland and Colorado have a significantly lower bacterial diversity, while Sweden and Washington state are dominated by Bifidobacterium in early life. Bacterial community diversity over time is significantly different by geographical location. The microbiome of high-risk infants is associated with geographical location. Future studies aiming to identify the microbiome disease phenotype need to carefully consider the geographical origin of subjects. © 2015 by the American Diabetes Association. Readers may use this article as long as the work is properly cited, the use is educational and not for profit, and the work is not altered.

  17. Biodegradable polymeric nanoparticles show high efficacy and specificity at DNA delivery to human glioblastoma in vitro and in vivo.

    Science.gov (United States)

    Guerrero-Cázares, Hugo; Tzeng, Stephany Y; Young, Noah P; Abutaleb, Ameer O; Quiñones-Hinojosa, Alfredo; Green, Jordan J

    2014-05-27

    Current glioblastoma therapies are insufficient to prevent tumor recurrence and eventual death. Here, we describe a method to treat malignant glioma by nonviral DNA delivery using biodegradable poly(β-amino ester)s (PBAEs), with a focus on the brain tumor initiating cells (BTICs), the tumor cell population believed to be responsible for the formation of new tumors and resistance to many conventional therapies. We show transfection efficacy of >60% and low biomaterial-mediated cytotoxicity in primary human BTICs in vitro even when the BTICs are grown as 3-D oncospheres. Intriguingly, we find that these polymeric nanoparticles show intrinsic specificity for nonviral transfection of primary human BTICs over primary healthy human neural progenitor cells and that this specificity is not due to differences in cellular growth rate or total cellular uptake of nanoparticles. Moreover, we demonstrate that biodegradable PBAE/DNA nanoparticles can be fabricated, lyophilized, and then stored for at least 2 years without losing efficacy, increasing the translational relevance of this technology. Using lyophilized nanoparticles, we show transgene expression by tumor cells after intratumoral injection into an orthotopic murine model of human glioblastoma. PBAE/DNA nanoparticles were more effective than naked DNA at exogenous gene expression in vivo, and tumor cells were transfected more effectively than noninvaded brain parenchyma in vivo. This work shows the potential of nonviral gene delivery tools to target human brain tumors.

  18. How surface composition of high milk proteins powders is influenced by spray-drying temperature.

    Science.gov (United States)

    Gaiani, C; Morand, M; Sanchez, C; Tehrany, E Arab; Jacquot, M; Schuck, P; Jeantet, R; Scher, J

    2010-01-01

    High milk proteins powders are common ingredients in many food products. The surface composition of these powders is expected to play an essential role during their storage, handling and/or final application. Therefore, an eventual control of the surface composition by modifying the spray-drying temperature could be very useful in the improvement of powder quality and the development of new applications. For this purpose, the influence of five spray-drying temperatures upon the surface composition of the powders was investigated by X-ray photoelectron spectroscopy. The major milk proteins were studied: native micellar casein and native whey, both more or less enriched in lactose. The results show a surface enrichment in lipids for all the powders and in proteins for many powders. Whatever the drying temperature, lipids and proteins are preferentially located near the surface whereas lactose is found in the core. This surface enrichment is also highly affected by the spray-drying temperature. More lipids, more proteins and less lactose are systematically observed at the surface of powders spray-dried at lower outlet air temperatures. The nature of proteins is also found essential; surface enrichment in lipids being much stronger for whey proteins containing powders than for casein containing powders. Additionally, we found a direct correlation between the lipids surface concentration and the wetting ability for the 25 powders studied.

  19. High surface area aerogels for energy storage and efficiency

    Science.gov (United States)

    Maloney, Ryan Patrick

    The dissertation is divided into two main chapters, each focused on a different application for aerogel. The first chapter concerns the development of silica aerogel for thermal insulation. It begins with initial characterization of a silica aerogel insulation for a next-generation Advanced Radioisotope Stirling Generator for space vehicles. While the aerogel as made performs well, it is apparent that further improvements in mechanical strength and durability are necessary. The chapter then continues with the exploration of chlorotrimethysilane surface modification, which somewhat surprisingly provides a drastic increase in mechanical properties, allowing the inherently brittle silica network to deform plastically to >80% strain. It is hypothesized that the hydrophobic surface groups reduce capillary forces during drying, lowering the number of microcracks that may form and weaken the gel. This surface modification scheme is then implemented in a fiber-reinforced, opacified aerogel insulation for a prototypical thermoelectric generator for automotive waste heat recovery. This is the first known report of aerogel insulation for thermoelectrics. The aerogel insulation is able to increase the efficiency of the thermoelectric generator by 40% compared with commercial high-temperature insulating wool. Unfortunately, the supercritical drying process adds significant cost to the aerogel insulation, limiting its commercial viability. The chapter then culminates in the development and characterization of an Ambiently Dried Aerogel Insulation (ADAI) that eliminates the need for expensive supercritical drying. It is believed that this report represents the first aerogel insulation that can be dried without undergoing a large volume change before "springing back" to near its original volume, which allows it to be cast into place into complex geometries and around rigid inclusions. This reduces a large barrier to the commercial viability of aerogel insulation. The advantages of

  20. High microsatellite and mitochondrial diversity in Anatolian native horse breeds shows Anatolia as a genetic conduit between Europe and Asia.

    Science.gov (United States)

    Koban, E; Denizci, M; Aslan, O; Aktoprakligil, D; Aksu, S; Bower, M; Balcioglu, B K; Ozdemir Bahadir, A; Bilgin, R; Erdag, B; Bagis, H; Arat, S

    2012-08-01

    The horse has been a food source, but more importantly, it has been a means for transport. Its domestication was one of the crucial steps in the history of human civilization. Despite the archaeological and molecular studies carried out on the history of horse domestication, which would contribute to conservation of the breeds, the details of the domestication of horses still remain to be resolved. We employed 21 microsatellite loci and mitochondrial control region partial sequences to analyse genetic variability within and among four Anatolian native horse breeds, Ayvacık Pony, Malakan Horse, Hınıs Horse and Canik Horse, as well as samples from indigenous horses of unknown breed ancestry. The aims of the study were twofold: first, to produce data from the prehistorically and historically important land bridge, Anatolia, in order to assess its role in horse domestication and second, to analyse the data from a conservation perspective to help the ministry improve conservation and management strategies regarding native horse breeds. Even though the microsatellite data revealed a high allelic diversity, 98% of the genetic variation partitioned within groups. Genetic structure did not correlate with a breed or geographic origin. High diversity was also detected in mtDNA control region sequence analysis. Frequencies of two haplogroups (HC and HF) revealed a cline between Asia and Europe, suggesting Anatolia as a probable connection route between the two continents. This first detailed genetic study on Anatolian horse breeds revealed high diversity among horse mtDNA haplogroups in Anatolia and suggested Anatolia's role as a conduit between the two continents. The study also provides an important basis for conservation practices in Turkey. © 2011 The Authors, Animal Genetics © 2011 Stichting International Foundation for Animal Genetics.

  1. Large surface radiative forcing from surface-based ice crystal events measured in the High Arctic at Eureka

    Directory of Open Access Journals (Sweden)

    G. Lesins

    2008-09-01

    Full Text Available Ice crystals, also known as diamond dust, are suspended in the boundary layer air under clear sky conditions during most of the Arctic winter in Northern Canada. Occasionally ice crystal events can produce significantly thick layers with optical depths in excess of 2.0 even in the absence of liquid water clouds. Four case studies of high optical depth ice crystal events at Eureka in the Nunavut Territory of Canada during the winter of 2006–2007 are presented. They show that the measured ice crystal surface infrared downward radiative forcing ranged from 8 to 36 W m−2 in the wavelength band from 5.6 to 20 μm for visible optical depths ranging from 0.2 to 1.7. MODIS infrared and visible images and the operational radiosonde wind profile were used to show that these high optical depth events were caused by surface snow being blown off 600 to 800 m high mountain ridges about 20 to 30 km North-West of Eureka and advected by the winds towards Eureka as they settled towards the ground within the highly stable boundary layer. This work presents the first study that demonstrates the important role that surrounding topography plays in determining the occurrence of high optical depth ice crystal events and points to a new source of boundary layer ice crystal events distinct from the classical diamond dust phenomenon.

  2. Synthesis, Modelling, and Anticonvulsant Studies of New Quinazolines Showing Three Highly Active Compounds with Low Toxicity and High Affinity to the GABA-A Receptor.

    Science.gov (United States)

    Zayed, Mohamed F; Ihmaid, Saleh K; Ahmed, Hany E A; El-Adl, Khaled; Asiri, Ahmed M; Omar, Abdelsattar M

    2017-01-24

    Some novel fluorinated quinazolines (5a-j) were designed and synthesized to be evaluated for their anticonvulsant activity and their neurotoxicity. Structures of all newly synthesized compounds were confirmed by their infrared (IR), mass spectrometry (MS) spectra, ¹H nuclear magnetic resonance (NMR), (13)C-NMR, and elemental analysis (CHN). The anticonvulsant activity was evaluated by a subcutaneous pentylenetetrazole (scPTZ) test and maximal electroshock (MES)-induced seizure test, while neurotoxicity was evaluated by a rotorod test. The molecular docking was performed for all newly-synthesized compounds to assess their binding affinities to the GABA-A receptor in order to rationalize their anticonvulsant activities in a qualitative way. The data obtained from the molecular modeling was correlated with that obtained from the biological screening. These data showed considerable anticonvulsant activity for all newly-synthesized compounds. Compounds 5b, 5c, and 5d showed the highest binding affinities toward the GABA-A receptor, along with the highest anticonvulsant activities in experimental mice. These compounds also showed low neurotoxicity and low toxicity in the median lethal dose test compared to the reference drugs. A GABA enzymatic assay was performed for these highly active compounds to confirm the obtained results and explain the possible mechanism for anticonvulsant action. The most active compounds might be used as leads for future modification and optimization.

  3. The interactome of Streptococcus pneumoniae and its bacteriophages show highly specific patterns of interactions among bacteria and their phages.

    Science.gov (United States)

    Mariano, Rachelle; Wuchty, Stefan; Vizoso-Pinto, Maria G; Häuser, Roman; Uetz, Peter

    2016-04-22

    Although an abundance of bacteriophages exists, little is known about interactions between their proteins and those of their bacterial hosts. Here, we experimentally determined the phage-host interactomes of the phages Dp-1 and Cp-1 and their underlying protein interaction network in the host Streptococcus pneumoniae. We compared our results to the interaction patterns of E. coli phages lambda and T7. Dp-1 and Cp-1 target highly connected host proteins, occupy central network positions, and reach many protein clusters through the interactions of their targets. In turn, lambda and T7 targets cluster to conserved and essential proteins in E. coli, while such patterns were largely absent in S. pneumoniae. Furthermore, targets in E. coli were mutually strongly intertwined, while targets of Dp-1 and Cp-1 were strongly connected through essential and orthologous proteins in their immediate network vicinity. In both phage-host systems, the impact of phages on their protein targets appears to extend from their network neighbors, since proteins that interact with phage targets were located in central network positions, have a strong topologically disruptive effect and touch complexes with high functional heterogeneity. Such observations suggest that the phages, biological impact is accomplished through a surprisingly limited topological reach of their targets.

  4. New classes of alanine racemase inhibitors identified by high-throughput screening show antimicrobial activity against Mycobacterium tuberculosis.

    Directory of Open Access Journals (Sweden)

    Karen G Anthony

    Full Text Available BACKGROUND: In an effort to discover new drugs to treat tuberculosis (TB we chose alanine racemase as the target of our drug discovery efforts. In Mycobacterium tuberculosis, the causative agent of TB, alanine racemase plays an essential role in cell wall synthesis as it racemizes L-alanine into D-alanine, a key building block in the biosynthesis of peptidoglycan. Good antimicrobial effects have been achieved by inhibition of this enzyme with suicide substrates, but the clinical utility of this class of inhibitors is limited due to their lack of target specificity and toxicity. Therefore, inhibitors that are not substrate analogs and that act through different mechanisms of enzyme inhibition are necessary for therapeutic development for this drug target. METHODOLOGY/PRINCIPAL FINDINGS: To obtain non-substrate alanine racemase inhibitors, we developed a high-throughput screening platform and screened 53,000 small molecule compounds for enzyme-specific inhibitors. We examined the 'hits' for structural novelty, antimicrobial activity against M. tuberculosis, general cellular cytotoxicity, and mechanism of enzyme inhibition. We identified seventeen novel non-substrate alanine racemase inhibitors that are structurally different than any currently known enzyme inhibitors. Seven of these are active against M. tuberculosis and minimally cytotoxic against mammalian cells. CONCLUSIONS/SIGNIFICANCE: This study highlights the feasibility of obtaining novel alanine racemase inhibitor lead compounds by high-throughput screening for development of new anti-TB agents.

  5. csd alleles in the red dwarf honey bee (Apis florea,Hymenoptera: Apidae) show exceptionally high nucleotide diversity

    Institute of Scientific and Technical Information of China (English)

    Zhi-Yong Liu; Zi-Long Wang; Xiao-Bo Wu; Wei-Yu Yan; Zhi-Jiang Zeng

    2011-01-01

    The single locus complementary sex determination (sl-csd) gene is the primary gene determining the gender of honey bees (Apis spp.).While the csd gene has been well studied in the Western honey bee (Apis mellifera),and comparable data exist in both the Eastern honey bee (Apis cerana) and the giant honey bee (Apis dorsata),no studies have been conducted in the red dwarf honey bee,Apisflorea.In this study we cloned the genomic region 3 of the A.florea csd gene from 60 workers,and identified 12 csd alleles.Analysis showed that similar to A.mellifera,region 3 of the csd gene contains a RS domain at the N terminal,a proline-rich domain at the C terminal,and a hypervariable region in the middle.However,the A.florea csd gene possessed a much higher level of nucleotide diversity,compared to A.mellifera,A.cerana and Apis dorsata.We also show that similar to the other three Apis species,in A.florea,nonsynonymous mutations in the csd gene are selectively favored in young alleles.

  6. Preparation of activated carbon with high surface area for high-capacity methane storage

    Institute of Scientific and Technical Information of China (English)

    Bingsi Liua; Wenshuo Wanga; Na Wanga; Peter Chak Tong Aub

    2014-01-01

    Activated carbon (AC) was fabricated from corncob, which is cheap and abundant. Experimental parameters such as particle size of corncob, KOH/char weight ratio, and activation temperature and time were optimized to generate AC, which shows high methane sorption capacity. AC has high specific surface area (3227 m2/g), with pore volume and pore size distribution equal to 1.829 cm3/g and ca. 1.7-2.2 nm, respectively. Under the condition of 2◦C and less than 7.8 MPa, methane sorption in the presence of water (Rw=1.4) was as high as 43.7 wt%methane per unit mass of dry AC. The result is significantly higher than those of coconut-derived AC (32 wt%) and ordered mesoporous carbon (41.2 wt%, Rw=4.07) under the same condition. The physical properties and amorphous chaotic structure of AC were characterized by N2 adsorption isotherms, XRD, SEM and HRTEM. Hence, the corncob-derived AC can be considered as a competitive methane-storage material for vehicles, which are run by natural gas.

  7. Surface and structure modification induced by high energy and highly charged uranium ion irradiation in monocrystal spinel

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Yitao, E-mail: yangyt@impcas.ac.cn [Materials Research Center, Institute of Modern Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Zhang, Chonghong; Song, Yin; Gou, Jie; Zhang, Liqing [Materials Research Center, Institute of Modern Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Meng, Yancheng; Zhang, Hengqing [Materials Research Center, Institute of Modern Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Ma, Yizhun [Materials Research Center, Institute of Modern Physics, Chinese Academy of Sciences, Lanzhou 730000 (China)

    2014-05-01

    Due to its high temperature properties and relatively good behavior under irradiation, magnesium aluminate spinel (MgAl{sub 2}O{sub 4}) is considered as a possible material to be used as inert matrix for the minor actinides burning. In this case, irradiation damage is an unavoidable problem. In this study, high energy and highly charged uranium ions (290 MeV U{sup 32+}) were used to irradiate monocrystal spinel to the fluence of 1.0 × 10{sup 13} ions/cm{sup 2} to study the modification of surface and structure. Highly charged ions carry large potential energy, when they interact with a surface, the release of potential energy results in the modification of surface. Atomic force microscopy (AFM) results showed the occurrence of etching on surface after uranium ion irradiation. The etching depth reached 540 nm. The surprising efficiency of etching is considered to be induced by the deposition of potential energy with high density. The X-ray diffraction results showed that the (4 4 0) diffraction peak obviously broadened after irradiation, which indicated that the distortion of lattice has occurred. After multi-peak Gaussian fitting, four Gaussian peaks were separated, which implied that a structure with different damage layers could be formed after irradiation.

  8. Asymmetric spline surfaces - Characteristics and applications. [in high quality optical systems design

    Science.gov (United States)

    Stacy, J. E.

    1984-01-01

    Asymmetric spline surfaces appear useful for the design of high-quality general optical systems (systems without symmetries). A spline influence function defined as the actual surface resulting from a simple perturbation in the spline definition array shows that a subarea is independent of others four or more points away. Optimization methods presented in this paper are used to vary a reflective spline surface near the focal plane of a decentered Schmidt-Cassegrain to reduce rms spot radii by a factor of 3 across the field.

  9. X-ray spectra induced in highly charged 40Arq+ interacting with Au surface

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    By use of optical spectrum technology, the spectra of X-ray induced by highly charged 40Arq+ ions interacting with Au surface have been studied. The results show that the argon Kα X-ray were emitted from the hollow atoms formed below the surface. There is a process of multi-electron exciting in neutralization of the Ar16+ion, with electronic configuration 1s2 in its ground state below the solid surface. The yield of the projectile Kα X-ray is related to its initial electronic configuration, and the yield of the target X-ray is related to the projectile kinetic energy.

  10. Impact of high resolution land surface initialization in Indian summer monsoon simulation using a regional climate model

    Science.gov (United States)

    Unnikrishnan, C. K.; Rajeevan, M.; Rao, S. Vijaya Bhaskara

    2016-06-01

    The direct impact of high resolution land surface initialization on the forecast bias in a regional climate model in recent years over Indian summer monsoon region is investigated. Two sets of regional climate model simulations are performed, one with a coarse resolution land surface initial conditions and second one used a high resolution land surface data for initial condition. The results show that all monsoon years respond differently to the high resolution land surface initialization. The drought monsoon year 2009 and extended break periods were more sensitive to the high resolution land surface initialization. These results suggest that the drought monsoon year predictions can be improved with high resolution land surface initialization. Result also shows that there are differences in the response to the land surface initialization within the monsoon season. Case studies of heat wave and a monsoon depression simulation show that, the model biases were also improved with high resolution land surface initialization. These results show the need for a better land surface initialization strategy in high resolution regional models for monsoon forecasting.

  11. Manganese Dioxide with High Specific Surface Area for Alkaline Battery

    Institute of Scientific and Technical Information of China (English)

    HUANG You-ju; LIN Yu-li; LI Wei-shan

    2012-01-01

    The authors reported a facile method for the synthesis of manganese dioxide without any template and catalyst at a low-temperature.The prepared sample was characterized with X-ray diffraction(XRD),scanning electron microscopy(SEM),Brunauer-Emmett-Teller(BET) surface analysis,Fourier transform infrared(FTIR) spectrometry,cyclic voltammetry,altemative current(AC) impedance test and battery discharge test.It is found that the prepared sample belongs to α-MnO2 and has a microsphere morphology and a large BET surface area.The electrochemical characterization indicates that the prepared sample displays a larger electrochemical capacitance than the commercial electrolytic manganese dioxides(EMD) in Na2SO4 solution,and exhibits larger discharge capacity than EMD,especially at a high rate discharge condition when it is used as cathode of alkaline Zn/MnO2 battery.

  12. Preparation, Surface and Pore Structure of High Surface Area Activated Carbon Fibers from Bamboo by Steam Activation

    Directory of Open Access Journals (Sweden)

    Xiaojun Ma

    2014-06-01

    Full Text Available High surface area activated carbon fibers (ACF have been prepared from bamboo by steam activation after liquefaction and curing. The influences of activation temperature on the microstructure, surface area and porosity were investigated. The results showed that ACF from bamboo at 850 °C have the maximum iodine and methylene blue adsorption values. Aside from the graphitic carbon, phenolic and carbonyl groups were the predominant functions on the surface of activated carbon fiber from bamboo. The prepared ACF from bamboo were found to be mainly type I of isotherm, but the mesoporosity presented an increasing trend after 700 °C. The surface area and micropore volume of samples, which were determined by application of the Brunauer-Emmett-Teller (BET and t-plot methods, were as high as 2024 m2/g and 0.569 cm3/g, respectively. It was also found that the higher activation temperature produced the more ordered microcrystalline structure of ACF from bamboo.

  13. Global gene analysis of oocytes from early stages in human folliculogenesis shows high expression of novel genes in reproduction.

    Science.gov (United States)

    Markholt, S; Grøndahl, M L; Ernst, E H; Andersen, C Yding; Ernst, E; Lykke-Hartmann, K

    2012-02-01

    The pool of primordial follicles in humans is laid down during embryonic development and follicles can remain dormant for prolonged intervals, often decades, until individual follicles resume growth. The mechanisms that induce growth and maturation of primordial follicles are poorly understood but follicles once activated either continue growth or undergo atresia. We have isolated pure populations of oocytes from human primordial, intermediate and primary follicles using laser capture micro-dissection microscopy and evaluated the global gene expression profiles by whole-genome microarray analysis. The array data were confirmed by qPCR for selected genes. A total of 6301 unique genes were identified as significantly expressed representing enriched specific functional categories such as 'RNA binding', 'translation initiation' and 'structural molecule activity'. Several genes, some not previously known to be associated with early oocyte development, were identified with exceptionally high expression levels, such as the anti-proliferative transmembrane protein with an epidermal growth factor-like and two follistatin-like domains (TMEFF2), the Rho-GTPase-activating protein oligophrenin 1 (OPHN1) and the mitochondrial-encoded ATPase6 (ATP6). Thus, the present study provides not only a technique to capture and perform transcriptome analysis of the sparse material of human oocytes from the earliest follicle stages but further includes a comprehensive basis for our understanding of the regulatory factors and pathways present during early human folliculogenesis.

  14. Batrachochytrium dendrobatidis shows high genetic diversity and ecological niche specificity among haplotypes in the Maya Mountains of Belize.

    Directory of Open Access Journals (Sweden)

    Kristine Kaiser

    Full Text Available The amphibian pathogen Batrachochytrium dendrobatidis (Bd has been implicated in amphibian declines around the globe. Although it has been found in most countries in Central America, its presence has never been assessed in Belize. We set out to determine the range, prevalence, and diversity of Bd using quantitative PCR (qPCR and sequencing of a portion of the 5.8 s and ITS1-2 regions. Swabs were collected from 524 amphibians of at least 26 species in the protected areas of the Maya Mountains of Belize. We sequenced a subset of 72 samples that had tested positive for Bd by qPCR at least once; 30 samples were verified as Bd. Eight unique Bd haplotypes were identified in the Maya Mountains, five of which were previously undescribed. We identified unique ecological niches for the two most broadly distributed haplotypes. Combined with data showing differing virulence shown in different strains in other studies, the 5.8 s - ITS1-2 region diversity found in this study suggests that there may be substantial differences among populations or haplotypes. Future work should focus on whether specific haplotypes for other genomic regions and possibly pathogenicity can be associated with haplotypes at this locus, as well as the integration of molecular tools with other ecological tools to elucidate the ecology and pathogenicity of Bd.

  15. Dentinal surface-cutting efficiency using a high-speed diamond bur, ultrasound and laser

    Science.gov (United States)

    Youssef, M.; Quinelato, A.; Youssef, F.; Pelino, J. E. Pelizon; Salvadori, M. C.; Mori, M.

    2008-04-01

    We compare an ultrasound bur with a conventional one and an Er:YAG laser for cavity preparations. Human molars were embedded in resin and sliced for this study. The surface abrasion was performed by a high-speed instrument and ultrasound. The cavity preparation was initially performed with a high-speed diamond bur. After this, a 2.94-μm laser with 400 mJ/pulse at 4 Hz, and a pulse width from 250-500 μs was applied to the tooth surface for 30 s in a sweeping motion. The samples were analyzed by SEM. The abrasion surface with a conventional bur showed structure removal with different grooves, a smear-layer presence, and occluded dentinal tubules. The abraded surface with the CVD bur suggested a removal process in layers. The laser-irradiated surface showed a rough aspect with opened tubules and the absence of a smear layer. The results of this study suggest that a high-speed diamond bur, ultrasound, and laser were able to perform cavity preparation. However, the CVD bur presented a higher surface quality.

  16. HIV-infected patients show functionally defective high-density lipoprotein (HDL paralleled with changes in HDL-associated proteins

    Directory of Open Access Journals (Sweden)

    V Estrada

    2012-11-01

    Full Text Available Purpose of the study Epidemiological studies have consistently demonstrated an inverse association between plasma HDL concentrations and cardiovascular risk. Although this cardioprotective role has been mainly attributed to its role in promoting cellular cholesterol efflux, there is an emerging interest in the anti-inflammatory and antioxidant properties of HDL. The aim of the study is to investigate the anti-inflammatory properties of HDL isolated from HIV-infected patients. Methods Cross-sectional study of 113 HIV-infected patients and 70 non-infected control subjects without evident CVD. From each subject, HDL was isolated by ultracentrifugation and its anti-inflammatory status was tested as its ability to inhibit MCP-1-induced migration of the monocytic cell line THP-1 using transwell cell culture chamber inserts with micropore filters of 5 microns pore size. HDL-associated proteins were measured by commercial ELISAs. Results Twenty-three HIV-infected patients were ART-naïve (32±15 years, 66.7% male and ninety were currently on ART (46±11 years, 78.9 % male. Most patients on ART (91.1% had undetectable viral load (<50 copies/mL. When compared to healthy subjects, both naïve and treated HIV-infected patients had lower plasma HDL-cholesterol levels (naïve: 45±12, ART: 50±10, controls: 55±10 mg/dL, p<0.05. HDL isolated from HIV naïve patients showed a significantly reduced anti-inflammatory activity (THP-1 monocyte migration capacity was 203% times higher in HIV patients than in control subjects. The anti-inflammatory activity of HDL from ART-treated HIV-infected patients was significantly improved when compared to naïve patients, although it remained significantly lower than controls (130% THP-1 monocyte migration vs controls. HDL from HIV-infected patients had a decreased concentration of the anti-inflammatory proteins Apo A1 (controls: 2.1±0.3, naïve: 1.4±0.2, ART: 1.6±0.1 mg/ml and LCAT (controls: 0.53±0.09, naïve: 0.34±0

  17. High surface area carbon for bifunctional air electrodes applied in zinc-air batteries

    Energy Technology Data Exchange (ETDEWEB)

    Arai, H. [on leave from NTT Laboratories (Japan); Mueller, S.; Haas, O. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

    1999-08-01

    Bifunctional air electrodes with high surface area carbon substrates showed low reduction overpotential, thus are promising for enhancing the energy efficiency and power capability of zinc-air batteries. The improved performance is attributed to lower overpotential due to diffusion of the reaction intermediate, namely the peroxide ion. (author) 1 fig., 2 refs.

  18. High levels of surface differential rotation on the young G0 dwarf HD 171488

    NARCIS (Netherlands)

    Jeffers, S.V.; Donati, J.F.

    2008-01-01

    We present high-resolution images of the young, rapidly rotating G0 dwarf HD 171488, using both Stokes I and Stokes V data. The observations were secured with the MuSiCoS spectropolarimeter at Telescope Bernard Lyot from 2005 May 31 to June 10. The photospheric surface brightness distributions show

  19. ALMA Observations Show Major Mergers Among the Host Galaxies of Fast-growing, High-redshift​ Supermassive​ Black Holes

    Science.gov (United States)

    Trakhtenbrot, Benny; Lira, Paulina; Netzer, Hagai; Cicone, Claudia; Maiolino, Roberto; Shemmer, Ohad

    2017-02-01

    We present new ALMA band-7 data for a sample of six luminous quasars at z≃ 4.8, powered by fast-growing supermassive black holes (SMBHs) with rather uniform properties: the typical accretion rates and black hole masses are L/{L}{Edd}≃ 0.7 and {M}{BH}≃ {10}9 {M}ȯ . Our sample consists of three “FIR-bright” sources, which were individually detected in previous Herschel/SPIRE observations, with star formation rates of {SFR}> 1000 {M}ȯ {{yr}}-1, and three “FIR-faint” sources for which Herschel stacking analysis implies a typical SFR of ∼400 {M}ȯ {{yr}}-1. The dusty interstellar medium in the hosts of all six quasars is clearly detected in the ALMA data and resolved on scales of ∼2 kpc, in both continuum ({λ }{rest}∼ 150 μ {{m}}) and [{{C}} {{II}}] λ 157.74 μ {{m}} line emission. The continuum emission is in good agreement with the expectations from the Herschel data, confirming the intense SF activity in the quasar hosts. Importantly, we detect companion sub-millimeter galaxies (SMGs) for three sources—one FIR-bright and two FIR-faint, separated by ∼ 14{--}45 {kpc} and ALMA data therefore clearly support the idea that major mergers are important drivers for rapid early SMBH growth. However, the fact that not all high-SFR quasar hosts are accompanied by interacting SMGs and the gas kinematics as observed by ALMA suggest that other processes may be fueling these systems. Our analysis thus demonstrates the diversity of host galaxy properties and gas accretion mechanisms associated with early and rapid SMBH growth.

  20. Genome characteristics of a novel phage from Bacillus thuringiensis showing high similarity with phage from Bacillus cereus.

    Directory of Open Access Journals (Sweden)

    Yihui Yuan

    Full Text Available Bacillus thuringiensis is an important entomopathogenic bacterium belongs to the Bacillus cereus group, which also includes B. anthracis and B. cereus. Several genomes of phages originating from this group had been sequenced, but no genome of Siphoviridae phage from B. thuringiensis has been reported. We recently sequenced and analyzed the genome of a novel phage, BtCS33, from a B. thuringiensis strain, subsp. kurstaki CS33, and compared the gneome of this phage to other phages of the B. cereus group. BtCS33 was the first Siphoviridae phage among the sequenced B. thuringiensis phages. It produced small, turbid plaques on bacterial plates and had a narrow host range. BtCS33 possessed a linear, double-stranded DNA genome of 41,992 bp with 57 putative open reading frames (ORFs. It had a typical genome structure consisting of three modules: the "late" region, the "lysogeny-lysis" region and the "early" region. BtCS33 exhibited high similarity with several phages, B. cereus phage Wβ and some variants of Wβ, in genome organization and the amino acid sequences of structural proteins. There were two ORFs, ORF22 and ORF35, in the genome of BtCS33 that were also found in the genomes of B. cereus phage Wβ and may be involved in regulating sporulation of the host cell. Based on these observations and analysis of phylogenetic trees, we deduced that B. thuringiensis phage BtCS33 and B. cereus phage Wβ may have a common distant ancestor.

  1. A metamaterial electromagnetic energy rectifying surface with high harvesting efficiency

    Science.gov (United States)

    Duan, Xin; Chen, Xing; Zhou, Lin

    2016-12-01

    A novel metamaterial rectifying surface (MRS) for electromagnetic energy capture and rectification with high harvesting efficiency is presented. It is fabricated on a three-layer printed circuit board, which comprises an array of periodic metamaterial particles in the shape of mirrored split rings, a metal ground, and integrated rectifiers employing Schottky diodes. Perfect impedance matching is engineered at two interfaces, i.e. one between free space and the surface, and the other between the metamaterial particles and the rectifiers, which are connected through optimally positioned vias. Therefore, the incident electromagnetic power is captured with almost no reflection by the metamaterial particles, then channeled maximally to the rectifiers, and finally converted to direct current efficiently. Moreover, the rectifiers are behind the metal ground, avoiding the disturbance of high power incident electromagnetic waves. Such a MRS working at 2.45 GHz is designed, manufactured and measured, achieving a harvesting efficiency up to 66.9% under an incident power density of 5 mW/cm2, compared with a simulated efficiency of 72.9%. This high harvesting efficiency makes the proposed MRS an effective receiving device in practical microwave power transmission applications.

  2. Sulfur passivation of surface electrons in highly Mg-doped InN

    Energy Technology Data Exchange (ETDEWEB)

    Linhart, W. M.; Veal, T. D. [Stephenson Institute for Renewable Energy and Department of Physics, University of Liverpool, Liverpool L69 4ZF (United Kingdom); Chai, J. [Department of Electrical and Computer Engineering, University of Canterbury, Christchurch 8140 (New Zealand); McConville, C. F. [Department of Physics, University of Warwick, Coventry CV4 7AL (United Kingdom); Durbin, S. M. [Department of Electrical and Computer Engineering, University of Canterbury, Christchurch 8140 (New Zealand); Department of Electrical and Computer Engineering, Western Michigan University, Kalamazoo, Michigan 49008 (United States)

    2013-09-14

    Electron accumulation with a sheet density greater than 10{sup 13} cm{sup −2} usually occurs at InN surfaces. Here, the effects of treatment with ammonium sulfide ((NH{sub 4}){sub 2}S{sub x}) on the surface electronic properties of highly Mg-doped InN (>4×10{sup 18} cm{sup −3}) have been investigated with high resolution x-ray photoemission spectroscopy. The valence band photoemission spectra show that the surface Fermi level decreases by approximately 0.08 eV with (NH{sub 4}){sub 2}S{sub x} treatment, resulting in a decrease of the downward band bending and up to a 70% reduction in the surface electron sheet density.

  3. Fractal Dimension of Fracture Surface in Rock Material after High Temperature

    Directory of Open Access Journals (Sweden)

    Z. Z. Zhang

    2015-01-01

    Full Text Available Experiments on granite specimens after different high temperature under uniaxial compression were conducted and the fracture surfaces were observed by scanning electron microscope (SEM. The fractal dimensions of the fracture surfaces with increasing temperature were calculated, respectively. The fractal dimension of fracture surface is between 1.44 and 1.63. Its value approximately goes up exponentially with the increase of temperature. There is a quadratic polynomial relationship between the rockburst tendency and fractal dimension of fracture surface; namely, a fractal dimension threshold can be obtained. Below the threshold value, a positive correlativity shows between rockburst tendency and fractal dimension; when the fractal dimension is greater than the threshold value, it shows an inverse correlativity.

  4. Investigation of Surface Damage in Forming of High Strength and Galvanized Steel Sheets

    Institute of Scientific and Technical Information of China (English)

    Zhongqi Yu; Yingke Hou; Haomin Jiang; Xinping Chen; Weigang Zhang

    2009-01-01

    Powdering/exfoliating of coatings and scratching are the main forms of surface damage in the forming of galvanized steels and high strength steels (HSS), which result in increased die maintenance cost and scrap rate.In this study, a special rectangular box was developed to investigate the behavior and characteristics of surface damage in sheet metal forming (SMF) processes.U-channel forming tests were conducted to study the effect of tool hardness on surface damage in the forming of high strength steels and galvanized steels (hot-dip galvanized and galvannealed steels).Experimental results indicate that sheet deformation mode influences the severity of surface damage in SMF and surface damage occurs easily at the regions where sheet specimen deforms under the action of compressive stress.Die corner is the position where surface damage initiates.For HSS sheet, surface damage is of major interest due to high forming pressure.The HSS and hot-dip galvanized steels show improved ability of damage-resistance with increased hardness of the forming tool.However, for galvannealed steel it is not the forming tool with the highest hardness value that performs best.

  5. Progressive FastICA Peel-Off and Convolution Kernel Compensation Demonstrate High Agreement for High Density Surface EMG Decomposition

    Science.gov (United States)

    Chen, Maoqi

    2016-01-01

    Decomposition of electromyograms (EMG) is a key approach to investigating motor unit plasticity. Various signal processing techniques have been developed for high density surface EMG decomposition, among which the convolution kernel compensation (CKC) has achieved high decomposition yield with extensive validation. Very recently, a progressive FastICA peel-off (PFP) framework has also been developed for high density surface EMG decomposition. In this study, the CKC and PFP methods were independently applied to decompose the same sets of high density surface EMG signals. Across 91 trials of 64-channel surface EMG signals recorded from the first dorsal interosseous (FDI) muscle of 9 neurologically intact subjects, there were a total of 1477 motor units identified from the two methods, including 969 common motor units. On average, 10.6 ± 4.3 common motor units were identified from each trial, which showed a very high matching rate of 97.85 ± 1.85% in their discharge instants. The high degree of agreement of common motor units from the CKC and the PFP processing provides supportive evidence of the decomposition accuracy for both methods. The different motor units obtained from each method also suggest that combination of the two methods may have the potential to further increase the decomposition yield. PMID:27642525

  6. Progressive FastICA Peel-Off and Convolution Kernel Compensation Demonstrate High Agreement for High Density Surface EMG Decomposition.

    Science.gov (United States)

    Chen, Maoqi; Holobar, Ales; Zhang, Xu; Zhou, Ping

    2016-01-01

    Decomposition of electromyograms (EMG) is a key approach to investigating motor unit plasticity. Various signal processing techniques have been developed for high density surface EMG decomposition, among which the convolution kernel compensation (CKC) has achieved high decomposition yield with extensive validation. Very recently, a progressive FastICA peel-off (PFP) framework has also been developed for high density surface EMG decomposition. In this study, the CKC and PFP methods were independently applied to decompose the same sets of high density surface EMG signals. Across 91 trials of 64-channel surface EMG signals recorded from the first dorsal interosseous (FDI) muscle of 9 neurologically intact subjects, there were a total of 1477 motor units identified from the two methods, including 969 common motor units. On average, 10.6 ± 4.3 common motor units were identified from each trial, which showed a very high matching rate of 97.85 ± 1.85% in their discharge instants. The high degree of agreement of common motor units from the CKC and the PFP processing provides supportive evidence of the decomposition accuracy for both methods. The different motor units obtained from each method also suggest that combination of the two methods may have the potential to further increase the decomposition yield.

  7. Progressive FastICA Peel-Off and Convolution Kernel Compensation Demonstrate High Agreement for High Density Surface EMG Decomposition

    Directory of Open Access Journals (Sweden)

    Maoqi Chen

    2016-01-01

    Full Text Available Decomposition of electromyograms (EMG is a key approach to investigating motor unit plasticity. Various signal processing techniques have been developed for high density surface EMG decomposition, among which the convolution kernel compensation (CKC has achieved high decomposition yield with extensive validation. Very recently, a progressive FastICA peel-off (PFP framework has also been developed for high density surface EMG decomposition. In this study, the CKC and PFP methods were independently applied to decompose the same sets of high density surface EMG signals. Across 91 trials of 64-channel surface EMG signals recorded from the first dorsal interosseous (FDI muscle of 9 neurologically intact subjects, there were a total of 1477 motor units identified from the two methods, including 969 common motor units. On average, 10.6±4.3 common motor units were identified from each trial, which showed a very high matching rate of 97.85±1.85% in their discharge instants. The high degree of agreement of common motor units from the CKC and the PFP processing provides supportive evidence of the decomposition accuracy for both methods. The different motor units obtained from each method also suggest that combination of the two methods may have the potential to further increase the decomposition yield.

  8. High surface area graphene-supported metal chalcogenide assembly

    Science.gov (United States)

    Worsley, Marcus A.; Kuntz, Joshua; Orme, Christine A.

    2016-04-19

    A composition comprising at least one graphene-supported assembly, which comprises a three-dimensional network of graphene sheets crosslinked by covalent carbon bonds, and at least one metal chalcogenide compound disposed on said graphene sheets, wherein the chalcogen of said metal chalcogenide compound is selected from S, Se and Te. Also disclosed are methods for making and using the graphene-supported assembly, including graphene-supported MoS.sub.2. Monoliths with high surface area and conductivity can be achieved. Lower operating temperatures in some applications can be achieved. Pore size and volume can be tuned.

  9. High-speed particle image velocimetry near surfaces.

    Science.gov (United States)

    Lu, Louise; Sick, Volker

    2013-06-24

    Multi-dimensional and transient flows play a key role in many areas of science, engineering, and health sciences but are often not well understood. The complex nature of these flows may be studied using particle image velocimetry (PIV), a laser-based imaging technique for optically accessible flows. Though many forms of PIV exist that extend the technique beyond the original planar two-component velocity measurement capabilities, the basic PIV system consists of a light source (laser), a camera, tracer particles, and analysis algorithms. The imaging and recording parameters, the light source, and the algorithms are adjusted to optimize the recording for the flow of interest and obtain valid velocity data. Common PIV investigations measure two-component velocities in a plane at a few frames per second. However, recent developments in instrumentation have facilitated high-frame rate (>1 kHz) measurements capable of resolving transient flows with high temporal resolution. Therefore, high-frame rate measurements have enabled investigations on the evolution of the structure and dynamics of highly transient flows. These investigations play a critical role in understanding the fundamental physics of complex flows. A detailed description for performing high-resolution, high-speed planar PIV to study a transient flow near the surface of a flat plate is presented here. Details for adjusting the parameter constraints such as image and recording properties, the laser sheet properties, and processing algorithms to adapt PIV for any flow of interest are included.

  10. Designing high-temperature steels via surface science and thermodynamics

    Science.gov (United States)

    Gross, Cameron T.; Jiang, Zilin; Mathai, Allan; Chung, Yip-Wah

    2016-06-01

    Electricity in many countries such as the US and China is produced by burning fossil fuels in steam-turbine-driven power plants. The efficiency of these power plants can be improved by increasing the operating temperature of the steam generator. In this work, we adopted a combined surface science and computational thermodynamics approach to the design of high-temperature, corrosion-resistant steels for this application. The result is a low-carbon ferritic steel with nanosized transition metal monocarbide precipitates that are thermally stable, as verified by atom probe tomography. High-temperature Vickers hardness measurements demonstrated that these steels maintain their strength for extended periods at 700 °C. We hypothesize that the improved strength of these steels is derived from the semi-coherent interfaces of these thermally stable, nanosized precipitates exerting drag forces on impinging dislocations, thus maintaining strength at elevated temperatures.

  11. HIGH IMPEDANCE SURFACES FOR FLEXIBLE AND CONFORMAL WIRELESS SYSTEMS

    Directory of Open Access Journals (Sweden)

    Haider R. Khaleel

    2014-01-01

    Full Text Available Recent years have witnessed a great deal of interest from both scientific and academic communities in the field of flexible electronic systems. Most flexible electronic systems require the integration of flexible antennas operating in specific frequency bands to provide wireless connectivity which is highly demanded by today’s network oriented society. On the other hand, High Impedance Surfaces have become very popular in the design of contemporary antenna and micro-wave devices due to their wide range of applications derived from their unique electromagnetic properties which significantly enhance the performance of antennas and RF systems. Accordingly, the integration of HIS structures within flexible wireless systems is very beneficial in this growing field of research. In this paper, a systematic review of flexible HIS structures reported in the literature is conducted, which provides the reader with a thorough description and a complete list of state of the art designs intended for flexible wireless systems.

  12. Highly variable Pliocene sea surface conditions in the Norwegian Sea

    Science.gov (United States)

    Bachem, Paul E.; Risebrobakken, Bjørg; De Schepper, Stijn; McClymont, Erin L.

    2017-09-01

    The Pliocene was a time of global warmth with small sporadic glaciations, which transitioned towards the larger-scale Pleistocene glacial-interglacial variability. Here, we present high-resolution records of sea surface temperature (SST) and ice-rafted debris (IRD) in the Norwegian Sea from 5.32 to 3.14 Ma, providing evidence that the Pliocene surface conditions of the Norwegian Sea underwent a series of transitions in response to orbital forcing and gateway changes. Average SSTs are 2 °C above the regional Holocene mean, with notable variability on millennial to orbital timescales. Both gradual changes and threshold effects are proposed for the progression of regional climate towards the Late Pliocene intensification of Northern Hemisphere glaciation. Cooling from 4.5 to 4.3 Ma may be linked to the onset of poleward flow through the Bering Strait. This cooling was further intensified by a period of cool summers due to weak obliquity forcing. A 7 °C warming of the Norwegian Sea at 4.0 Ma suggests a major increase in northward heat transport from the North Atlantic, leading to an enhanced zonal SST gradient in the Nordic Seas, which may be linked to the expansion of sea ice in the Arctic and Nordic Seas. A warm Norwegian Sea and enhanced zonal temperature gradient between 4.0 and 3.6 Ma may have been a priming factor for increased glaciation around the Nordic Seas due to enhanced evaporation and precipitation at high northern latitudes.

  13. Submonolayer Quantum Dots for High Speed Surface Emitting Lasers

    Directory of Open Access Journals (Sweden)

    Zakharov ND

    2007-01-01

    Full Text Available AbstractWe report on progress in growth and applications of submonolayer (SML quantum dots (QDs in high-speed vertical-cavity surface-emitting lasers (VCSELs. SML deposition enables controlled formation of high density QD arrays with good size and shape uniformity. Further increase in excitonic absorption and gain is possible with vertical stacking of SML QDs using ultrathin spacer layers. Vertically correlated, tilted or anticorrelated arrangements of the SML islands are realized and allow QD strain and wavefunction engineering. Respectively, both TE and TM polarizations of the luminescence can be achieved in the edge-emission using the same constituting materials. SML QDs provide ultrahigh modal gain, reduced temperature depletion and gain saturation effects when used in active media in laser diodes. Temperature robustness up to 100 °C for 0.98 μm range vertical-cavity surface-emitting lasers (VCSELs is realized in the continuous wave regime. An open eye 20 Gb/s operation with bit error rates better than 10−12has been achieved in a temperature range 25–85 °Cwithout current adjustment. Relaxation oscillations up to ∼30 GHz have been realized indicating feasibility of 40 Gb/s signal transmission.

  14. Surface morphology and deuterium retention in tungsten exposed to high flux D plasma at high temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Jia, Y.Z. [Laboratory of Advanced Materials, School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); De Temmerman, G. [FOM Institute DIFFER-Dutch Institute for Fundamental Energy Research, Edisonbaan 14, 3439 MN Nieuwegein (Netherlands); ITER Organization, Route de Vinon-sur-Verdon-CS90046, 13067 St Paul Lez Durance Cedex (France); Luo, G.-N. [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Xu, H.Y. [Science and Technology on Surface Physics and Chemistry Laboratory, Mianyang, Sichuan 621907 (China); Li, C.; Fu, B.Q. [Laboratory of Advanced Materials, School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Liu, W., E-mail: liuw@mail.tsinghua.edu.cn [Laboratory of Advanced Materials, School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China)

    2015-02-15

    Surface modifications and deuterium retention induced in tungsten by high fluxes (10{sup 24} m{sup −2} s{sup −1}) low energy (38 eV) deuterium ions were studied as a function of surface temperature. Blister formation was studied by scanning electron microscopy and electron backscatter diffraction, while deuterium retention was measured by thermal desorption spectroscopy. Blisters are observed on the surface exposed at different temperatures, ranging from 493 K to 1273 K. The blister density and D retention decrease with the increasing exposure temperature. The formation of blisters at high temperatures is attributed to the high flux of D plasma. At 943 K, with the increasing fluence, there is trend to the saturation of D retention and blister density. The defects caused by plasma exposure have an important effect on the D trapping and blistering behavior. The formation of blisters has a strong relationship with slipping system of tungsten.

  15. CNPC SHOWS HIGH CORPORATE RESPONSIBILITY

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    As Chinese companies expand globally, they are not merely buying up raw materials and tapping new markets. They are also adding local jobs, establishing universities and research institutions and building up community schools and hospitals in an attempt to improve their reputations and establish better relations with local communities.

  16. An in situ vapour phase hydrothermal surface doping approach for fabrication of high performance Co3O4 electrocatalysts with an exceptionally high S-doped active surface.

    Science.gov (United States)

    Tan, Zhijin; Liu, Porun; Zhang, Haimin; Wang, Yun; Al-Mamun, Mohammad; Yang, Hua Gui; Wang, Dan; Tang, Zhiyong; Zhao, Huijun

    2015-04-04

    A facile in situ vapour phase hydrothermal (VPH) surface doping approach has been developed for fabrication of high performance S-doped Co3O4 electrocatalysts with an unprecedentedly high surface S content (>47%). The demonstrated VPH doping approach could be useful for enrichment of surface active sites for other metal oxide electrocatalysts.

  17. Electron capture by highly charged ions from surfaces and gases

    Energy Technology Data Exchange (ETDEWEB)

    Allen, F.

    2008-01-11

    In this study highly charged ions produced in Electron Beam Ion Traps are used to investigate electron capture from surfaces and gases. The experiments with gas targets focus on spectroscopic measurements of the K-shell x-rays emitted at the end of radiative cascades following electron capture into Rydberg states of Ar{sup 17+} and Ar{sup 18+} ions as a function of collision energy. The ions are extracted from an Electron Beam Ion Trap at an energy of 2 keVu{sup -1}, charge-selected and then decelerated down to 5 eVu{sup -1} for interaction with an argon gas target. For decreasing collision energies a shift to electron capture into low orbital angular momentum capture states is observed. Comparative measurements of the K-shell x-ray emission following electron capture by Ar{sup 17+} and Ar{sup 18+} ions from background gas in the trap are made and a discrepancy in the results compared with those from the extraction experiments is found. Possible explanations are discussed. For the investigation of electron capture from surfaces, highly charged ions are extracted from an Electron Beam Ion Trap at energies of 2 to 3 keVu{sup -1}, charge-selected and directed onto targets comprising arrays of nanoscale apertures in silicon nitride membranes. The highly charged ions implemented are Ar{sup 16+} and Xe{sup 44+} and the aperture targets are formed by focused ion beam drilling in combination with ion beam assisted thin film deposition, achieving hole diameters of 50 to 300 nm and aspect ratios of 1:5 to 3:2. After transport through the nanoscale apertures the ions pass through an electrostatic charge state analyzer and are detected. The percentage of electron capture from the aperture walls is found to be much lower than model predictions and the results are discussed in terms of a capillary guiding mechanism. (orig.)

  18. Surface hardening utilizing high-density plasma nitriding on stainless steel alloys

    Energy Technology Data Exchange (ETDEWEB)

    Lleonart-Davila, G; Gaudier, J; Rivera, R; Leal, D; Gonzalez-Lizardo, A; Leal-Quiros, E [Plasma Engineering Laboratory, Polytechnic University of Puerto Rico, San Juan, PR 00918 (Puerto Rico)

    2008-10-15

    By using a plasma nitriding procedure at the PUPR Mirror Cusp Plasma machine, surface hardness is increased in 302/304-type stainless steel samples by exposing them to high-ion-density plasma at high vacuum. This method successfully dopes the surface of the material with strengthening nitrogen ions, without the use of chemical procedures that sacrifice the resistance to corrosion of the given material. A 500 V negative bias is placed on the sample exposed to the nitrogen plasma, where high-energy ions are therefore attracted and immersed into the metallic matrix microns into the surface of the stainless steel. This potential maintains a constant surface temperature at approximately 800 deg. C. The plasma parameters including ion density and plasma temperature were diagnosed using single Langmuir probes. The stainless steel samples were then tested using scanning electron microscopy (SEM), and Vickers micro-hardness testing to determine the increment in the surface harness of the material. The SEM showed a significant presence of nitrogen imbedded in the grains of the stainless steel surface.

  19. Impact of high resolution land surface initialization in Indian summer monsoon simulation using a regional climate model

    Indian Academy of Sciences (India)

    C K Unnikrishnan; M Rajeevan; S Vijaya Bhaskara Rao

    2016-06-01

    The direct impact of high resolution land surface initialization on the forecast bias in a regional climatemodel in recent years over Indian summer monsoon region is investigated. Two sets of regional climatemodel simulations are performed, one with a coarse resolution land surface initial conditions and secondone used a high resolution land surface data for initial condition. The results show that all monsoonyears respond differently to the high resolution land surface initialization. The drought monsoon year2009 and extended break periods were more sensitive to the high resolution land surface initialization.These results suggest that the drought monsoon year predictions can be improved with high resolutionland surface initialization. Result also shows that there are differences in the response to the land surfaceinitialization within the monsoon season. Case studies of heat wave and a monsoon depression simulationshow that, the model biases were also improved with high resolution land surface initialization. Theseresults show the need for a better land surface initialization strategy in high resolution regional modelsfor monsoon forecasting.

  20. Analysis of cosmid clones of nuclear DNA from Trypanosome brucei shows that the genes for variant surface glycoproteins are clustered in the genome.

    NARCIS (Netherlands)

    D. Valerio (Dinko); T. de Lange; P. Borst (Piet); F.G. Grosveld (Frank); L.H.T. van der Ploeg

    1982-01-01

    textabstractTrypanosoma brucei contains more than a hundred genes coding for the different variant surface glycoproteins (VSGs). Activation of some of these genes involves the duplication of the gene (the basic copy or BC) and transposition of the duplicate to an expression site (yielding the expres

  1. Fusion peptide P15-CSP shows antibiofilm activity and pro-osteogenic activity when deposited as a coating on hydrophilic but not hydrophobic surfaces.

    Science.gov (United States)

    Li, Xian; Contreras-Garcia, Angel; LoVetri, Karen; Yakandawala, Nandadeva; Wertheimer, Michael R; De Crescenzo, Gregory; Hoemann, Caroline D

    2015-12-01

    In the context of porous bone void filler for oral bone reconstruction, peptides that suppress microbial growth and promote osteoblast function could be used to enhance the performance of a porous bone void filler. We tested the hypothesis that P15-CSP, a novel fusion peptide containing collagen-mimetic osteogenic peptide P15, and competence-stimulating peptide (CSP), a cationic antimicrobial peptide, has emerging properties not shared by P15 or CSP alone. Peptide-coated surfaces were tested for antimicrobial activity toward Streptoccocus mutans, and their ability to promote human mesenchymal stem cell (MSC) attachment, spreading, metabolism, and osteogenesis. In the osteogenesis assay, peptides were coated on tissue culture plastic and on thin films generated by plasma-enhanced chemical vapor deposition to have hydrophilic or hydrophobic character (water contact angles 63°, 42°, and 92°, respectively). S. mutans planktonic growth was specifically inhibited by CSP, whereas biofilm formation was inhibited by P15-CSP. MSC adhesion and actin stress fiber formation was strongly enhanced by CSP, P15-CSP, and fibronectin coatings and modestly enhanced by P15 versus uncoated surfaces. Metabolic assays revealed that CSP was slightly cytotoxic to MSCs. MSCs developed alkaline phosphatase activity on all surfaces, with or without peptide coatings, and consistently deposited the most biomineralized matrix on hydrophilic surfaces coated with P15-CSP. Hydrophobic thin films completely suppressed MSC biomineralization, consistent with previous findings of suppressed osteogenesis on hydrophobic bioplastics. Collective data in this study provide new evidence that P15-CSP has unique dual capacity to suppress biofilm formation, and to enhance osteogenic activity as a coating on hydrophilic surfaces.

  2. Theoretical study of cathode surfaces and high-temperature superconductors

    Science.gov (United States)

    Mueller, Wolfgang

    1995-01-01

    Calculations are presented for the work functions of BaO on W, Os, Pt, and alloys of Re-W, Os-W, and Ir-W that are in excellent agreement with experiment. The observed emission enhancement for alloy relative to tungsten dispenser cathodes is attributed to properties of the substrate crystal structure and explained by the smaller depolarization of the surface dipole on hexagonal as compared to cubic substrates. For Ba and BaO on W(100), the geometry of the adsorbates has been determined by a comparison of inverse photoemission spectra with calculated densities of unoccupied states based on the fully relativistic embedded cluster approach. Results are also discussed for models of scandate cathodes and the electronic structure of oxygen on W(100) at room and elevated temperatures. A detailed comparison is made for the surface electronic structure of the high-temperature superconductor YBa2Cu3O7 as obtained with non-, quasi-, and fully relativistic cluster calculations.

  3. Highly Crystalline Multimetallic Nanoframes with Three-Dimensional Electrocatalytic Surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Chen [Univ. of California, Berkeley, CA (United States); Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Tsinghua Univ., Beijing (China); Kang, Yijin [Argonne National Lab. (ANL), Argonne, IL (United States); Huo, Ziyang [Univ. of California, Berkeley, CA (United States); Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Zhu, Zhongwei [Univ. of California, Berkeley, CA (United States); Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Huang, Wenyu [Univ. of California, Berkeley, CA (United States); Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Xin, Huolin [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Snyder, Joshua [Argonne National Lab. (ANL), Argonne, IL (United States); Li, Dongguo [Argonne National Lab. (ANL), Argonne, IL (United States); Herron, Jeffrey A. [Univ. of Wisconsin, Madison, WI (United States); Mavrikakis, Manos [Univ. of Wisconsin, Madison, WI (United States); Chi, Miaofang [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); More, Karren L. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Li, Yadong [Tsinghua Univ., Beijing (China); Markovic, Nenad M. [Argonne National Lab. (ANL), Argonne, IL (United States); Somorjai, Gabor A. [Univ. of California, Berkeley, CA (United States); Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Yang, Peidong [Univ. of California, Berkeley, CA (United States); Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); King Abdulaziz Univ., Jeddah (Saudia Arabia); Stamenkovic, Vojislav R. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2014-03-21

    Control of structure at the atomic level can precisely and effectively tune catalytic properties of materials, enabling enhancement in both activity and durability. We synthesized a highly active and durable class of electrocatalysts by exploiting the structural evolution of platinum-nickel (Pt-Ni) bimetallic nanocrystals. The starting material, crystalline PtNi3 polyhedra, transforms in solution by interior erosion into Pt3Ni nanoframes with surfaces that offer three-dimensional molecular accessibility. The edges of the Pt-rich PtNi3 polyhedra are maintained in the final Pt3Ni nanoframes. Both the interior and exterior catalytic surfaces of this open-framework structure are composed of the nanosegregated Pt-skin structure, which exhibits enhanced oxygen reduction reaction (ORR) activity. The Pt3Ni nanoframe catalysts achieved a factor of 36 enhancement in mass activity and a factor of 22 enhancement in specific activity, respectively, for this reaction (relative to state-of-the-art platinum-carbon catalysts) during prolonged exposure to reaction conditions.

  4. Superhydrophobic, Biomimetic Surfaces with High and Low Adhesion, Optical Transmittance, and Nanoscale Mechanical Wear Resistance

    Science.gov (United States)

    Ebert, Daniel R.

    Superhydrophobic surfaces (defined as surfaces having water contact angle greater than 150°) show great promise for use in a rapidly growing number of engineering applications, ranging from biomedical devices to fluid drag reduction in pipelines. In nature, the surfaces of many organisms, such as certain plant leaves, are known to exhibit superhydrophobicity. In some cases, droplet adhesion is very low (droplet rolls away easily), while in other cases adhesion is high (droplet remains adhered when surface is inverted). The recent advent and development of microscopes with resolution down to a few nanometers (such as atomic force microscopes and scanning electron microscopes) has allowed for in-depth understanding of the micro- and nanoscale mechanisms employed by these plant leaves and other natural surfaces to achieve their particular wetting properties. Biomimetics (or "mimicking nature") is therefore a very promising approach for the development of engineering surfaces with desired wetting characteristics. However, research in creating biomimetic surfaces is still in its early stages, and many of the surfaces created thus far are not mechanically robust, which is required for many potential real-world applications. In addition, for applications such as self-cleaning windows and solar panels, optical transparency is required. In this thesis, a set of original studies are presented in which superhydrophobic surfaces were designed based on biomimetics and fabricated using a wide of variety of techniques. The surfaces were characterized with regard to wetting characteristics such as water contact angle and contact angle hysteresis, micro- and nanoscale mechanical durability, and in some cases optical transmittance. Theoretical wetting models served as guides both in the design and in the understanding of experimental results, especially in regard to different wetting regime and regime transition. This work provides important conclusions and valuable insight for

  5. Translational symmetry of high order tokamak flux surface shaping in gyrokinetics

    CERN Document Server

    Ball, Justin; Barnes, Michael

    2015-01-01

    A particular translational symmetry of the local nonlinear $\\delta f$ gyrokinetic model is demonstrated analytically and verified numerically. This symmetry shows that poloidally translating all the flux surface shaping effects with large poloidal mode number by a single tilt angle has an exponentially small effect on the transport properties of a tokamak. This is shown using a generalization of the Miller local equilibrium model to specify an arbitrary flux surface geometry. With this geometry specification we find that, when performing an expansion in large flux surface shaping mode number, the governing equations of gyrokinetics are symmetric in the poloidal translation of the high order shaping effects. This allows us to take the fluxes from a single configuration and calculate the fluxes in any configuration that can be produced by translating the large mode number shaping effects. This creates a distinction between tokamaks with mirror symmetric flux surfaces and tokamaks without mirror symmetry, which ...

  6. Highly efficient singular surface plasmon generation by achiral apertures

    CERN Document Server

    Jiang, Quanbo; Bellessa, Joel; Huant, Serge; Genet, Cyriaque; Drezet, Aurélien

    2016-01-01

    We report a highly efficient generation of singular surface plasmon (SP) field by an achiral plasmonic structure consisting of $\\Lambda$-shaped apertures. Our quantitative analysis based on leakage radiation microscopy (LRM) demonstrates that the induced spin-orbit coupling can be tuned by adjusting the apex angle of the $\\Lambda$-shaped aperture. Specifically, the array of $\\Lambda$-shaped apertures with the apex angle $60^\\circ$ is shown to give rise to the directional coupling efficiency. The ring of $\\Lambda$-shaped apertures with the apex angle $60^\\circ$ realized to generate the maximum extinction ratio (ER=11) for the SP singularities between two different polarization states. This result provides a more efficient way for developing SP focusing and SP vortex in the field of nanophotonics such as optical tweezers.

  7. High surface area ThO/sub 2/ catalyst

    Science.gov (United States)

    Colmenares, C.A.; Somorjai, G.A.; Maj, J.J.

    1983-06-21

    A ThO/sub 2/ catalyst having a high surface area of about 80 to 125m/sup 2//g is synthesized. The compound is synthesized by simultaneously mixing an aqueous solution of ThNO/sub 3/(NO/sub 3/)/sub 4/.4H/sub 2/O with an aqueous solution of Na/sub 2/CO/sub 3/.H/sub 2/O, to produce a solution and solid ThOCO/sub 3/. The solid ThOCO/sub 3/ is separated from the solution, and then calcined at a temperature of about 225 to 300/sup 0/C for about 40 to 55 hours to produce ThO/sub 2/. The ThO/sub 2/ catalyst produced includes Na present as a substitutional cation in an amount equal to about 5 to 10 at. %.

  8. Core surface flow modelling from high-resolution secular variation

    DEFF Research Database (Denmark)

    Holme, R.; Olsen, Nils

    2006-01-01

    -flux hypothesis, but the spectrum of the SV implies that a conclusive test of frozen-flux is not possible. We parametrize the effects of diffusion as an expected misfit in the flow prediction due to departure from the frozen-flux hypothesis; at low spherical harmonic degrees, this contribution dominates...... the expected departure of the SV predictions from flow to the observed SV, while at high degrees the SV model uncertainty is dominant. We construct fine-scale core surface flows to model the SV. Flow non-uniqueness is a serious problem because the flows are sufficiently small scale to allow flow around non......-series of magnetic data and better parametrization of the external magnetic field....

  9. Highly variable Pliocene sea surface conditions in the Norwegian Sea

    Directory of Open Access Journals (Sweden)

    P. E. Bachem

    2017-09-01

    Full Text Available The Pliocene was a time of global warmth with small sporadic glaciations, which transitioned towards the larger-scale Pleistocene glacial–interglacial variability. Here, we present high-resolution records of sea surface temperature (SST and ice-rafted debris (IRD in the Norwegian Sea from 5.32 to 3.14 Ma, providing evidence that the Pliocene surface conditions of the Norwegian Sea underwent a series of transitions in response to orbital forcing and gateway changes. Average SSTs are 2 °C above the regional Holocene mean, with notable variability on millennial to orbital timescales. Both gradual changes and threshold effects are proposed for the progression of regional climate towards the Late Pliocene intensification of Northern Hemisphere glaciation. Cooling from 4.5 to 4.3 Ma may be linked to the onset of poleward flow through the Bering Strait. This cooling was further intensified by a period of cool summers due to weak obliquity forcing. A 7 °C warming of the Norwegian Sea at 4.0 Ma suggests a major increase in northward heat transport from the North Atlantic, leading to an enhanced zonal SST gradient in the Nordic Seas, which may be linked to the expansion of sea ice in the Arctic and Nordic Seas. A warm Norwegian Sea and enhanced zonal temperature gradient between 4.0 and 3.6 Ma may have been a priming factor for increased glaciation around the Nordic Seas due to enhanced evaporation and precipitation at high northern latitudes.

  10. Exposure to High Glucose Concentration Decreases Cell Surface ABCA1 and HDL Biogenesis in Hepatocytes.

    Science.gov (United States)

    Tsujita, Maki; Hossain, Mohammad Anwar; Lu, Rui; Tsuboi, Tomoe; Okumura-Noji, Kuniko; Yokoyama, Shinji

    2017-04-19

    To study atherosclerosis risk in diabetes, we investigated ATP-binding cassette transporter A1 (ABCA1) expression and high-density lipoprotein (HDL) biogenesis in the liver and hepatocytes under hyperglycemic conditions. In streptozotocin-induced diabetic mice, plasma HDL decreased while ABCA1 protein increased without changing its mRNA in the liver, only in the animals that responded to the treatment to show hypoinsulinemia and fasting hyperglycemia but not in the poor responders not showing those. To study the mechanism for this finding, hepatocytes were isolated from the control and diabetic mice, and they showed no difference in expression of ABCA1 protein, its mRNA, and HDL biogenesis in 1 g/l d-glucose but showed decreased HDL biogenesis in 4.5 g/l d-glucose although ABCA1 protein increased without change in its mRNA. Similar findings were confirmed in HepG2 cells with d-glucose but not with l-glucose. Thus, these cell models reproduced the in vivo findings in hyperglycemia. Labeling of cell surface protein revealed that surface ABCA1 decreased in high concentration of d-glucose in HepG2 cells despite the increase of cellular ABCA1 while not with l-glucose. Immunostaining of ABCA1 in HepG2 cells demonstrated the decrease of surface ABCA1 but increase of intracellular ABCA1 with high d-glucose. Clearance of ABCA1 was retarded both in primary hepatocytes and HepG2 cells exposed to high d-glucose but not to l-glucose, being consistent with the decrease of surface ABCA1. It is suggested that localization of ABCA1 to the cell surface is decreased in hepatocytes in hyperglycemic condition to cause decrease of HDL biogenesis.

  11. Construction of 4D high-definition cortical surface atlases of infants: Methods and applications.

    Science.gov (United States)

    Li, Gang; Wang, Li; Shi, Feng; Gilmore, John H; Lin, Weili; Shen, Dinggang

    2015-10-01

    In neuroimaging, cortical surface atlases play a fundamental role for spatial normalization, analysis, visualization, and comparison of results across individuals and different studies. However, existing cortical surface atlases created for adults are not suitable for infant brains during the first two postnatal years, which is the most dynamic period of postnatal structural and functional development of the highly-folded cerebral cortex. Therefore, spatiotemporal cortical surface atlases for infant brains are highly desired yet still lacking for accurate mapping of early dynamic brain development. To bridge this significant gap, leveraging our infant-dedicated computational pipeline for cortical surface-based analysis and the unique longitudinal infant MRI dataset acquired in our research center, in this paper, we construct the first spatiotemporal (4D) high-definition cortical surface atlases for the dynamic developing infant cortical structures at seven time points, including 1, 3, 6, 9, 12, 18, and 24 months of age, based on 202 serial MRI scans from 35 healthy infants. For this purpose, we develop a novel method to ensure the longitudinal consistency and unbiasedness to any specific subject and age in our 4D infant cortical surface atlases. Specifically, we first compute the within-subject mean cortical folding by unbiased groupwise registration of longitudinal cortical surfaces of each infant. Then we establish longitudinally-consistent and unbiased inter-subject cortical correspondences by groupwise registration of the geometric features of within-subject mean cortical folding across all infants. Our 4D surface atlases capture both longitudinally-consistent dynamic mean shape changes and the individual variability of cortical folding during early brain development. Experimental results on two independent infant MRI datasets show that using our 4D infant cortical surface atlases as templates leads to significantly improved accuracy for spatial normalization

  12. Nano-patterned superconducting surface for high quantum efficiency cathode

    Science.gov (United States)

    Hannon, Fay; Musumeci, Pietro

    2017-03-07

    A method for providing a superconducting surface on a laser-driven niobium cathode in order to increase the effective quantum efficiency. The enhanced surface increases the effective quantum efficiency by improving the laser absorption of the surface and enhancing the local electric field. The surface preparation method makes feasible the construction of superconducting radio frequency injectors with niobium as the photocathode. An array of nano-structures are provided on a flat surface of niobium. The nano-structures are dimensionally tailored to interact with a laser of specific wavelength to thereby increase the electron yield of the surface.

  13. Nano-patterned superconducting surface for high quantum efficiency cathode

    Energy Technology Data Exchange (ETDEWEB)

    Hannon, Fay; Musumeci, Pietro

    2017-03-07

    A method for providing a superconducting surface on a laser-driven niobium cathode in order to increase the effective quantum efficiency. The enhanced surface increases the effective quantum efficiency by improving the laser absorption of the surface and enhancing the local electric field. The surface preparation method makes feasible the construction of superconducting radio frequency injectors with niobium as the photocathode. An array of nano-structures are provided on a flat surface of niobium. The nano-structures are dimensionally tailored to interact with a laser of specific wavelength to thereby increase the electron yield of the surface.

  14. An Investigation into Surface Temperature Distributions of High-B Pulsars

    CERN Document Server

    Yasutake, Nobutoshi; Kutsuna, Masamichi; Shigeyama, Toshikazu

    2014-01-01

    Bearing in mind the application to high-magnetic-field (high-B) radio pulsars, we investigate two-dimensional (2D) thermal evolutions of neutron stars (NSs). We pay particular attention to the influence of different equilibrium configurations on the surface temperature distributions. The equilibrium configurations are constructed in a systematic manner, in which both toroidal and poloidal magnetic fields are determined self-consistently with the inclusion of general relativistic effects. To solve the 2D heat transfer inside the NS interior out to the crust, we have developed an implicit code based on a finite-difference scheme that deals with anisotropic thermal conductivity and relevant cooling processes in the context of a standard cooling scenario. In agreement with previous studies, the surface temperatures near the pole become higher than those in the vicinity of the equator as a result of anisotropic heat transfer. Our results show that the ratio of the highest to the lowest surface temperatures changes...

  15. Generalized potentiometric-surface map of the High Plains aquifer in Wyoming, 1981

    Science.gov (United States)

    Avery, Charles; Pettijohn, Robert A.

    1984-01-01

    A potentiometric-surface map shows the general configuration of the water surface for the High Plains Aquifer, which is composed of Oligocene age and younger rocks in southeastern Wyoming. The potentiometric contours are shown at 100-foot intervals on a map at a scale of 1:250,000. The High Plains Aquifer in Wyoming underlies an area of 8,190 square miles and geologically consists of the White River Formation of Oligocene age, the Arikaree Formation of early Miocene age, the Ogallala Formation of late Miocene age, and alluvial deposits of Quaternary age. The altitude of the potentiometric surface declines from about 7 ,100 feet in southwestern Laramie County to about 4,100 feet in eastern Goshen County. Typically, the slope is between 20 and 30 feet per mile; the general direction of flow is eastward. (USGS)

  16. Highly specific and sensitive electrochemical genotyping via gap ligation reaction and surface hybridization detection.

    Science.gov (United States)

    Huang, Yong; Zhang, Yan-Li; Xu, Xiangmin; Jiang, Jian-Hui; Shen, Guo-Li; Yu, Ru-Qin

    2009-02-25

    This paper developed a novel electrochemical genotyping strategy based on gap ligation reaction with surface hybridization detection. This strategy utilized homogeneous enzymatic reactions to generate molecular beacon-structured allele-specific products that could be cooperatively annealed to capture probes stably immobilized on the surface via disulfide anchors, thus allowing ultrasensitive surface hybridization detection of the allele-specific products through redox tags in close proximity to the electrode. Such a unique biphasic architecture provided a universal methodology for incorporating enzymatic discrimination reactions in electrochemical genotyping with desirable reproducibility, high efficiency and no interferences from interficial steric hindrance. The developed technique was demonstrated to show intrinsic high sensitivity for direct genomic analysis, and excellent specificity with discriminativity of single nucleotide variations.

  17. Characteristics of free-surface wave on high-speed liquid lithium jet for IFMIF

    Energy Technology Data Exchange (ETDEWEB)

    Kanemura, Takuji, E-mail: kanemura@stu.nucl.eng.osaka-u.ac.jp [Osaka University, 2-1 Yamada-oka, Suita, Osaka 565-0871 (Japan); Yoshihashi-Suzuki, Sachiko [Osaka University, 2-1 Yamada-oka, Suita, Osaka 565-0871 (Japan); Kondo, Hiroo [Japan Atomic Energy Agency, 2-4 Shirane Shirakata, Tokai-mura, Naka-gun, Ibaraki 319-1195 (Japan); Sugiura, Hirokazu; Yamaoka, Nobuo [Osaka University, 2-1 Yamada-oka, Suita, Osaka 565-0871 (Japan); Ida, Mizuho; Nakamura, Hiroo [Japan Atomic Energy Agency, 2-4 Shirane Shirakata, Tokai-mura, Naka-gun, Ibaraki 319-1195 (Japan); Matsushita, Izuru [Mitsubishi Heavy Industries Mechatronics Systems, Ltd., 1-16 5-chome, Komatsu-dori, Hyogo-ku, Kobe, Hyogo 652-0865 (Japan); Muroga, Takeo [National Institute for Fusion Science, 322-6 Oroshicho, Toki, Gifu 509-5292 (Japan); Horiike, Hiroshi [Osaka University, 2-1 Yamada-oka, Suita, Osaka 565-0871 (Japan)

    2011-10-01

    The characteristics of the surface waves on a high-speed liquid lithium wall jet were examined in a Li circulation loop at Osaka University for the International Fusion Materials Irradiation Facility (IFMIF). Surface fluctuations were measured by a contact-type liquid level sensor at 175 mm downstream from the nozzle exit, which corresponds to the deuteron beam's axis in the IFMIF, and observed with a high-speed video (HSV) camera. Both the observation and measurement results indicated that the surface fluctuations were composed of various scale turbulent fluctuations. The measurement results especially showed good agreement with the log-normal distribution which is one of the turbulent intermittency theories. The dominant wavelength was found to be shorter with increase in the flow velocity, and reached approximately 4 mm at the velocity of 15 m/s, which gave close agreement with the visually observed wavelength.

  18. High-resolution mapping of global surface water and its long-term changes

    Science.gov (United States)

    Pekel, Jean-François; Cottam, Andrew; Gorelick, Noel; Belward, Alan S.

    2016-12-01

    The location and persistence of surface water (inland and coastal) is both affected by climate and human activity and affects climate, biological diversity and human wellbeing. Global data sets documenting surface water location and seasonality have been produced from inventories and national descriptions, statistical extrapolation of regional data and satellite imagery, but measuring long-term changes at high resolution remains a challenge. Here, using three million Landsat satellite images, we quantify changes in global surface water over the past 32 years at 30-metre resolution. We record the months and years when water was present, where occurrence changed and what form changes took in terms of seasonality and persistence. Between 1984 and 2015 permanent surface water has disappeared from an area of almost 90,000 square kilometres, roughly equivalent to that of Lake Superior, though new permanent bodies of surface water covering 184,000 square kilometres have formed elsewhere. All continental regions show a net increase in permanent water, except Oceania, which has a fractional (one per cent) net loss. Much of the increase is from reservoir filling, although climate change is also implicated. Loss is more geographically concentrated than gain. Over 70 per cent of global net permanent water loss occurred in the Middle East and Central Asia, linked to drought and human actions including river diversion or damming and unregulated withdrawal. Losses in Australia and the USA linked to long-term droughts are also evident. This globally consistent, validated data set shows that impacts of climate change and climate oscillations on surface water occurrence can be measured and that evidence can be gathered to show how surface water is altered by human activities. We anticipate that this freely available data will improve the modelling of surface forcing, provide evidence of state and change in wetland ecotones (the transition areas between biomes), and inform water

  19. High-Quality Alkyl Monolayers on Silicon Surfaces

    NARCIS (Netherlands)

    Sieval, A.B.; Linke, R.; Zuilhof, H.; Sudh"lter, E.J.R.

    2000-01-01

    Covalent attachment of functionalized monolayers onto silicon surfaces (see Figure for examples) is presented here as a strategy for surface modification. The preparation and structure of both unfunctionalized and functionalized alkyl-based monolayers are described, as are potential applications,

  20. Surface strontium enrichment on highly active perovskites for oxygen electrocatalysis in solid oxide fuel cells

    KAUST Repository

    Crumlin, Ethan J.

    2012-01-01

    Perovskite oxides have high catalytic activities for oxygen electrocatalysis competitive to platinum at elevated temperatures. However, little is known about the oxide surface chemistry that influences the activity near ambient oxygen partial pressures, which hampers the design of highly active catalysts for many clean-energy technologies such as solid oxide fuel cells. Using in situ synchrotron-based, ambient pressure X-ray photoelectron spectroscopy to study the surface chemistry changes, we show that the coverage of surface secondary phases on a (001)-oriented La 0.8Sr 0.2CoO 3-δ (LSC) film becomes smaller than that on an LSC powder pellet at elevated temperatures. In addition, strontium (Sr) in the perovskite structure enriches towards the film surface in contrast to the pellet having no detectable changes with increasing temperature. We propose that the ability to reduce surface secondary phases and develop Sr-enriched perovskite surfaces of the LSC film contributes to its enhanced activity for O 2 electrocatalysis relative to LSC powder-based electrodes. © 2012 The Royal Society of Chemistry.

  1. High-surface-area silica nanospheres (KCC-1) with a fibrous morphology

    KAUST Repository

    Polshettiwar, Vivek

    2010-08-02

    Fibrous nanosilica: A new family of high-surface-area silica nanospheres (KCC-1) have been prepared (see picture). KCC-1 features excellent physical properties, including high surface area, unprecedented fibrous surface morphology, high thermal (up to 950 °C) and hydrothermal stabilities, and high mechanical stability. Copyright © 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  2. Snow surface microbiome on the High Antarctic Plateau (DOME C.

    Directory of Open Access Journals (Sweden)

    Luigi Michaud

    Full Text Available The cryosphere is an integral part of the global climate system and one of the major habitable ecosystems of Earth's biosphere. These permanently frozen environments harbor diverse, viable and metabolically active microbial populations that represent almost all the major phylogenetic groups. In this study, we investigated the microbial diversity in the surface snow surrounding the Concordia Research Station on the High Antarctic Plateau through a polyphasic approach, including direct prokaryotic quantification by flow cytometry and catalyzed reporter deposition fluorescence in situ hybridization (CARD-FISH, and phylogenetic identification by 16S RNA gene clone library sequencing and 454 16S amplicon pyrosequencing. Although the microbial abundance was low (<10(3 cells/ml of snowmelt, concordant results were obtained with the different techniques. The microbial community was mainly composed of members of the Alpha-proteobacteria class (e.g. Kiloniellaceae and Rhodobacteraceae, which is one of the most well-represented bacterial groups in marine habitats, Bacteroidetes (e.g. Cryomorphaceae and Flavobacteriaceae and Cyanobacteria. Based on our results, polar microorganisms could not only be considered as deposited airborne particles, but as an active component of the snowpack ecology of the High Antarctic Plateau.

  3. Ionic Behavior in Highly Concentrated Aqueous Solutions Nanoconfined between Discretely Charged Silicon Surfaces.

    Science.gov (United States)

    Qiu, Yinghua; Ma, Jian; Chen, Yunfei

    2016-05-17

    Through molecular dynamics simulations considering thermal vibration of surface atoms, ionic behaviors in concentrated NaCl solutions confined between discretely charged silicon surfaces have been investigated. The electric double layer structure was found to be sensitive to the density and distribution of surface charges. Due to the discreteness of the surface charge, a slight charge inversion appeared which depended on the surface charge density, bulk concentration, and confinement. In the nanoconfined NaCl solutions concentrated from 0.2 to 4.0 M, the locations of accumulation layers for Na(+) and Cl(-) ions remained stable, but their peak values increased. The higher the concentration was, the more obvious the charge inversion appeared. In 4.0 M NaCl solution, Na(+) and Cl(-) ions show obvious alternating layered distributions which may correspond to the solidification found in experiments. By changing surface separation, the confinement had a large effect on the ionic distribution. As both surfaces approached each other, many ions and water molecules were squeezed out of the confined space. Two adjacent layers in ion or water distribution profiles can be forced closer to each other and merge together. From ionic hydration analysis, the coordination number of Na(+) ions in highly confined space was much lower than that in the bulk.

  4. Simple and cost-effective fabrication of highly flexible, transparent superhydrophobic films with hierarchical surface design.

    Science.gov (United States)

    Kim, Tae-Hyun; Ha, Sung-Hun; Jang, Nam-Su; Kim, Jeonghyo; Kim, Ji Hoon; Park, Jong-Kweon; Lee, Deug-Woo; Lee, Jaebeom; Kim, Soo-Hyung; Kim, Jong-Man

    2015-03-11

    Optical transparency and mechanical flexibility are both of great importance for significantly expanding the applicability of superhydrophobic surfaces. Such features make it possible for functional surfaces to be applied to various glass-based products with different curvatures. In this work, we report on the simple and potentially cost-effective fabrication of highly flexible and transparent superhydrophobic films based on hierarchical surface design. The hierarchical surface morphology was easily fabricated by the simple transfer of a porous alumina membrane to the top surface of UV-imprinted polymeric micropillar arrays and subsequent chemical treatments. Through optimization of the hierarchical surface design, the resultant superhydrophobic films showed superior surface wetting properties (with a static contact angle of >170° and contact angle hysteresis of 82% at 550 nm wavelength). The superhydrophobic films were also experimentally found to be robust without significant degradation in the superhydrophobicity, even under repetitive bending and pressing for up to 2000 cycles. Finally, the practical usability of the proposed superhydorphobic films was clearly demonstrated by examining the antiwetting performance in real time while pouring water on the film and submerging the film in water.

  5. Multitechnique characterisation of 304L surface states oxidised at high temperature in steam and air atmospheres

    Science.gov (United States)

    Mamede, Anne-Sophie; Nuns, Nicolas; Cristol, Anne-Lise; Cantrel, Laurent; Souvi, Sidi; Cristol, Sylvain; Paul, Jean-François

    2016-04-01

    In case of a severe accident occurring in a nuclear reactor, surfaces of the reactor coolant system (RCS), made of stainless steel (304L) rich in Cr (>10%) and Ni (8-12%), are oxidised. Fission products (FPs) are released from melt fuel and flow through the RCS. A part of them is deposited onto surfaces either by vapour condensation or by aerosol deposition mechanisms. To be able to understand the nature of interactions between these FPs and the RCS surfaces, a preliminary step is to characterize the RSC surface states in steam and air atmosphere at high temperatures. Pieces of 304L stainless steel have been treated in a flow reactor at two different temperatures (750 °C and 950 °C) for two different exposition times (24 h and 72 h). After surfaces analysing by a unique combination of surface analysis techniques (XPS, ToF-SIMS and LEIS), for 304L, the results show a deep oxide scale with multi layers and the outer layer is composed of chromium and manganese oxides. Oxide profiles differ in air or steam atmosphere. Fe2O3 oxide is observed but in minor proportion and in all cases no nickel is detected near the surface. Results obtained are discussed and compared with the literature data.

  6. Electron dynamics at surfaces induced by highly charged ions

    NARCIS (Netherlands)

    Morgenstern, R

    1998-01-01

    Energy spectra of electrons resulting from hydrogen-like multiply charged N6+ and Q(7+) ions on various surfaces are presented and discussed. Por metal target surfaces thr formation and decay of hollow atoms during the approach towards the surface is rather well understood in terms of the classical

  7. Electron dynamics at surfaces induced by highly charged ions

    NARCIS (Netherlands)

    Morgenstern, R

    Energy spectra of electrons resulting from hydrogen-like multiply charged N6+ and Q(7+) ions on various surfaces are presented and discussed. Por metal target surfaces thr formation and decay of hollow atoms during the approach towards the surface is rather well understood in terms of the classical

  8. Dye-Sensitized Solar Cells Based on High Surface Area Nanocrystalline Zinc Oxide Spheres

    Directory of Open Access Journals (Sweden)

    Pavuluri Srinivasu

    2011-01-01

    Full Text Available High surface area nanocrystalline zinc oxide material is fabricated using mesoporous nanostructured carbon as a sacrificial template through combustion process. The resulting material is characterized by XRD, N2 adsorption, HR-SEM, and HR-TEM. The nitrogen adsorption measurement indicates that the materials possess BET specific surface area ca. 30 m2/g. Electron microscopy images prove that the zinc oxide spheres possess particle size in the range of 0.12 μm–0.17 μm. The nanocrystalline zinc oxide spheres show 1.0% of energy conversion efficiency for dye-sensitized solar cells.

  9. Surface stability and conductivity of a high Cr and Ni austenitic stainless steel plates for PEMFC

    Institute of Scientific and Technical Information of China (English)

    TIAN Rujin; SUN Juncai; WANG Jianli

    2006-01-01

    In order to use stainless steel as bipolar plate for PEMFC, electrochemical behavior of a high Cr and Ni austenitic stainless steel was studied in the solutions containing different concentration of H2SO4 and 2 mg·L-1 F-, and interfacial contact resistance was measured after corrosion tests. The experimental results show that the passive current density lowers with decreasing the concentration of H2SO4. The interfacial contact resistance between carbon paper and passive film formed in the simulated PEMFC environment is higher than the goal of bipolar plate for PEMFC. Surface conductivity should be further reduced by surface modification.

  10. Photocatalytic activities of tin(IV) oxide surface-modified titanium(IV) dioxide show a strong sensitivity to the TiO 2 crystal form

    OpenAIRE

    Jin, Qiliang; Fujishima, Musashi; Nolan, Michael; Iwaszuk, Anna; Tada, Hiroaki

    2012-01-01

    Surface modification of rutile TiO2 with extremely small SnO2 clusters gives rise to a great increase in its UV light activity for degradation of model organic water pollutants, while the effect is much smaller for anatase TiO2. This crystal form sensitivity is rationalized in terms of the difference in the electronic modification of TiO2 through the interfacial Sn−O−Ti bonds. The increase in the density of states near the conduction band minimum of rutile by hybridization with the SnO2 clust...

  11. A quantitative approach to defining "high-touch" surfaces in hospitals.

    Science.gov (United States)

    Huslage, Kirk; Rutala, William A; Sickbert-Bennett, Emily; Weber, David J

    2010-08-01

    Fifty interactions between healthcare workers and patients were observed to obtain a quantifiable definition of "high-touch" (ie, frequently touched) surfaces based on frequency of contact. Five surfaces were defined as high-touch surfaces: the bed rails, the bed surface, the supply cart, the over-bed table, and the intravenous pump.

  12. Biocompatible photocrosslinked poly(ester anhydride) based on functionalized poly(epsilon-caprolactone) prepolymer shows surface erosion controlled drug release in vitro and in vivo.

    Science.gov (United States)

    Mönkäre, J; Hakala, R A; Vlasova, M A; Huotari, A; Kilpeläinen, M; Kiviniemi, A; Meretoja, V; Herzig, K H; Korhonen, H; Seppälä, J V; Järvinen, K

    2010-09-15

    Star-shaped poly(epsilon-caprolactone) oligomers functionalized with succinic anhydride were used as prepolymers to prepare photocrosslinked poly(ester anhydride) to evaluate their in vivo drug delivery functionality and biocompatibility. Thus, in this work, erosion, drug release and safety of the photocrosslinked poly(ester anhydride) were examined in vitro and in vivo. A small water-soluble drug, propranolol HCl (M(w) 296 g/mol, solubility 50 mg/ml), was used as the model drug in an evaluation of the erosion controlled release. Drug-free and drug-loaded (10-60% w/w) poly(ester anhydride) discoids eroded in vitro (pH 7.4 buffer, +37 degrees C) linearly within 24-48 h. A strong correlation between the polymer erosion and the linear drug release in vitro was observed, indicating that the release had been controlled by the erosion of the polymer. Similarly, in vivo studies (s.c. implantation of discoids in rats) indicated that surface erosion controlled drug release from the discoids (drug loading 40% w/w). Oligomers did not decrease cell viability in vitro and the implanted discoids (s.c., rats) did not evoke any cytokine activity in vivo. In summary, surface erosion controlled drug release and the safety of photocrosslinked poly(ester anhydride) were demonstrated in this study.

  13. A high-affinity inhibitor of yeast carboxypeptidase Y is encoded by TFS1 and shows homology to a family of lipid binding proteins

    DEFF Research Database (Denmark)

    Bruun, A W; Svendsen, I; Sørensen, S O;

    1998-01-01

    degree of specificity, showing a 200-fold higher Ki toward a carboxypeptidase from Candida albicans which is highly homologous to carboxypeptidase Y. The TFS1 gene product shows extensive similarity to a class of proteins termed "21-23-kDa lipid binding proteins", members of which are found in several...

  14. High-performance silicon nanowire array photoelectrochemical solar cells through surface passivation and modification.

    Science.gov (United States)

    Wang, Xin; Peng, Kui-Qing; Pan, Xiao-Jun; Chen, Xue; Yang, Yang; Li, Li; Meng, Xiang-Min; Zhang, Wen-Jun; Lee, Shuit-Tong

    2011-10-10

    Nanowire solar cells: Pt nanoparticle (PtNP) decorated C/Si core/shell nanowire photoelectrochemical solar cells show high conversion efficiency of 10.86 % and excellent stability in aggressive electrolytes under 1-sun AM 1.5 G illumination. Superior device performance is achieved by improved surface passivation of the nanowires by carbon coating and enhanced interfacial charge transfer by PtNPs.

  15. The features of steel surface hardening with high energy heating by high frequency currents and shower cooling

    Science.gov (United States)

    Ivancivsky, V. V.; Skeeba, V. Yu; Bataev, I. A.; Lobanov, D. V.; Martyushev, N. V.; Sakha, O. V.; Khlebova, I. V.

    2016-11-01

    The paper examines the process of surface hardening of steel 45 with the help of high energy heating by high frequency currents with simultaneous shower water cooling. We theoretically justified and experimentally proved a possibility of liquid phase forming in the course of heating not on the surface, but in the depth of the surface layer.

  16. High Surface Area Ceria Nanoparticles via Hydrothermal Synthesis Experiment Design

    Directory of Open Access Journals (Sweden)

    Stanislav Kurajica

    2016-01-01

    Full Text Available Hydrothermal synthesis of CeO2 was optimized on two reactant concentrations and synthesis temperature and duration, in order to achieve material having the greatest specific surface area (SSA. Taguchi method of experimental design was employed in evaluation of the relative importance of synthesis parameters. CeO2 nanoparticles were characterized using X-ray diffraction, nitrogen adsorption-desorption isotherms, and scanning electron microscopy. Optimum conditions for obtaining particles with greater SSA were calculated according to Taguchi’s model “the-higher-the-better.” Synthesis temperature was found to be the only parameter significant for enabling nanoparticles with greater SSA. Mesoporous nanocrystalline ceria with SSA as great as 226 m2 g−1 was achieved, which is unprecedented for the hydrothermally synthesized ceria. The reason for this achievement was found in temperature dependence of the diffusion coefficient which, when low, favors nucleation yielding with fine particles, while when high it favors crystal growth and formation of one-dimensional structures. The occurrence of 1D-structure in sample exhibiting the smallest SSA was confirmed. Very fine crystallites with crystallite size as low as 5.9 nm have been obtained being roughly inverse proportional to SSA. Selected samples were tested as catalyst for soot oxidation. Catalyst morphology turned out to be decisive factor for catalytic activity.

  17. Facile synthesis of high surface area molybdenum nitride and carbide

    Science.gov (United States)

    Roy, Aaron; Serov, Alexey; Artyushkova, Kateryna; Brosha, Eric L.; Atanassov, Plamen; Ward, Tim L.

    2015-08-01

    The synthesis of high surface area γ-Mo2N and α-Mo2C is reported (116 and 120 m2/g) without the temperature programmed reduction of MoO3. γ-Mo2N was prepared in an NH3-free synthesis using forming gas (7 at% H2, N2-balance) as the reactive atmosphere. Three precursors were studied ((NH4)6Mo7O24·4H2O, (NH4)2 Mg(MoO4)2, and MgMoO4) along with the sacrificial support method (SSM) as a means of reducing the particle size of Mo2N and Mo2C. In situ X-ray diffraction (XRD) studies were carried out to identify reaction intermediates, the temperature at which various intermediates form, and the average domain size of the Mo2N products. Materials were synthesized in bulk and further characterized by XRD, HRTEM, XPS, and BET.

  18. 30 CFR 75.705-2 - Repairs to energized surface high-voltage lines.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Repairs to energized surface high-voltage lines... Repairs to energized surface high-voltage lines. An energized high-voltage surface line may be repaired... on power circuits with a phase-to-phase nominal voltage no greater than 15,000 volts; (3)...

  19. 30 CFR 75.705-10 - Tying into energized high-voltage surface circuits.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Tying into energized high-voltage surface....705-10 Tying into energized high-voltage surface circuits. If the work of forming an additional circuit by tying into an energized high-voltage surface line is performed from the ground, any...

  20. 30 CFR 77.704-10 - Tying into energized high-voltage surface circuits.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Tying into energized high-voltage surface... AREAS OF UNDERGROUND COAL MINES Grounding § 77.704-10 Tying into energized high-voltage surface circuits. If the work of forming an additional circuit by tying into an energized high-voltage surface line...

  1. High resolution land surface response of inland moving Indian monsoon depressions over Bay of Bengal

    Science.gov (United States)

    Rajesh, P. V.; Pattnaik, S.

    2016-05-01

    During Indian summer monsoon (ISM) season, nearly about half of the monsoonal rainfall is brought inland by the low pressure systems called as Monsoon Depressions (MDs). These systems bear large amount of rainfall and frequently give copious amount of rainfall over land regions, therefore accurate forecast of these synoptic scale systems at short time scale can help in disaster management, flood relief, food safety. The goal of this study is to investigate, whether an accurate moisture-rainfall feedback from land surface can improve the prediction of inland moving MDs. High Resolution Land Data Assimilation System (HRLDAS) is used to generate improved land state .i.e. soil moisture and soil temperature profiles by means of NOAH-MP land-surface model. Validation of the model simulated basic atmospheric parameters at surface layer and troposphere reveals that the incursion of high resolution land state yields least Root Mean Squared Error (RMSE) with a higher correlation coefficient and facilitates accurate depiction of MDs. Rainfall verification shows that HRLDAS simulations are spatially and quantitatively in more agreement with the observations and the improved surface characteristics could result in the realistic reproduction of the storm spatial structure, movement as well as intensity. These results signify the necessity of investigating more into the land surface-rainfall feedbacks through modifications in moisture flux convergence within the storm.

  2. Surface dynamics of amorphous polymers used for high-voltage insulators.

    Science.gov (United States)

    Shemella, Philip T; Laino, Teodoro; Fritz, Oliver; Curioni, Alessandro

    2011-11-24

    Amorphous siloxane polymers are the backbone of high-voltage insulation materials. The natural hydrophobicity of their surface is a necessary property for avoiding leakage currents and dielectric breakdown. As these surfaces are exposed to the environment, electrical discharges or strong mechanical impact can temporarily destroy their water-repellent properties. After such events, however, a self-healing process sets in and restores the original hydrophobicity within some hours. In the present study, we investigate possible mechanisms of this restoration process. Using large-scale, all-atom molecular dynamics simulations, we show that molecules on the material surface have augmented motion that allows them to rearrange with a net polarization. The overall surface region has a net orientation that contributes to hydrophobicity, and charged groups that are placed at the surface migrate inward, away from the vacuum interface and into the bulk-like region. Our simulations provide insight into the mechanisms for hydrophobic self-recovery that repair material strength and functionality and suggest material compositions for future high-voltage insulators.

  3. A facile method for preparing highly conductive and reflective surface-silvered polyimide films

    Science.gov (United States)

    Liao, Yuan; Cao, Bing; Wang, Wen-Cai; Zhang, Liqun; Wu, Dezhen; Jin, Riguang

    2009-07-01

    A novel method was developed for the preparation of reflective and electrically conductive surface-silvered polyimide (PI) films. The polyimide films were functionalized with poly(dopamine), simply by dipping the PI films into aqueous dopamine solution and mildly stirring at room temperature. Electroless plating of silver was readily carried out on the poly(dopamine) deposited PI (PI-DOPA) surface. The surface compositions of the modified PI films were studied by X-ray photoelectron spectroscopy (XPS). XPS results show that the PI-DOPA surfaces were successfully deposited with ploy(dopamine) and were ready for electroless deposition of silver. The poly(dopamine) layer was used not only as the chemi-sorption sites for silver particles during the electroless plating of silver, but also as an adhesion promotion layer for the electrolessly deposited silver. The as-prepared silvered PI films show high conductivity and reflectivity, with a surface resistance of 1.5 Ω and a reflectivity of 95%, respectively.

  4. A facile method for preparing highly conductive and reflective surface-silvered polyimide films

    Energy Technology Data Exchange (ETDEWEB)

    Liao Yuan; Cao Bing [State Key Laboratory of Chemical Resource Engineering, and the Key Laboratory of Beijing City on Preparation and Processing of Novel Polymer Materials, Beijing University of Chemical Technology, 15 Beisanhuan East Road, Beijing 100029 (China); Wang Wencai, E-mail: wangw@mail.buct.edu.cn [State Key Laboratory of Chemical Resource Engineering, and Key Laboratory of Beijing City on Preparation and Processing of Novel Polymer Materials, Beijing University of Chemical Technology, 15 Beisanhuan East Road, Beijing 100029 (China); Zhang Liqun; Wu Dezhen; Jin Riguang [State Key Laboratory of Chemical Resource Engineering, and Key Laboratory of Beijing City on Preparation and Processing of Novel Polymer Materials, Beijing University of Chemical Technology, 15 Beisanhuan East Road, Beijing 100029 (China)

    2009-07-15

    A novel method was developed for the preparation of reflective and electrically conductive surface-silvered polyimide (PI) films. The polyimide films were functionalized with poly(dopamine), simply by dipping the PI films into aqueous dopamine solution and mildly stirring at room temperature. Electroless plating of silver was readily carried out on the poly(dopamine) deposited PI (PI-DOPA) surface. The surface compositions of the modified PI films were studied by X-ray photoelectron spectroscopy (XPS). XPS results show that the PI-DOPA surfaces were successfully deposited with ploy(dopamine) and were ready for electroless deposition of silver. The poly(dopamine) layer was used not only as the chemi-sorption sites for silver particles during the electroless plating of silver, but also as an adhesion promotion layer for the electrolessly deposited silver. The as-prepared silvered PI films show high conductivity and reflectivity, with a surface resistance of 1.5 {Omega} and a reflectivity of 95%, respectively.

  5. Analysis of dipole-like ultra high frequency RFID tags close to metallic surfaces

    Institute of Scientific and Technical Information of China (English)

    Ling-fei MO; Hong-jian ZHANG; Hong-liang ZHOU

    2009-01-01

    It is a challenge for passive RFID tags to be mounted on the surface of metal because the parameters of tag antennas,such as the impedance matching, the radiation efficiency and the radiation pattern, are seriously affected by the metallic surface.This paper presents the characteristics of the dipole-like antennas of ultra high frequency (UHF) radio frequency identification (RFID) tags that are placed close to metallic surfaces. The finite element method (FEM) and method of moment (MoM) were used to simulate the changes of the antenna parameters near the metallic surface. Two typical dipole-like antennas close to the metallic surface, a closed loop antenna and a loaded meander antenna, were modeled, and the performance was evaluated. Experiment was carded out and the results were in good agreement with the simulation, showing that a distance of 0.05λ-0.1λ(λ is the free space wavelength) from the metallic surface could make the dipole-like UHF RFID tag performance be acceptable.

  6. OPTIMIZATION OF SURFACE RESISTIVITY AND RELATIVE PERMITTIVITY OF SILICONE RUBBER FOR HIGH VOLTAGE APPLICATION USING RESPONSE SURFACE METHODOLOGY

    Directory of Open Access Journals (Sweden)

    N.N. Ali

    2017-06-01

    Full Text Available Silicone Rubber (SiR is considered as one of the most established insulator in High Voltage (HV industry. SiR possess a great function ability such as its lighter weight, great heat resistance and substantial electrical insulation properties. Dynamic research were performed all around the world in order to explore the unique insulating behavior of SiR but very little are done on the optimization of SiR in term of their processing parameters and formulation. In this work, four materials and processing factors were introduced; A: Alumina Trihydrate (ATH, B: Dicumyl-Peroxide (DCP, C: mixing speed and D: mixing time in order to analyze its contribution towards improving the surface resistivity and relative permittivity of SIR rubber. The factors range were set based on prior screening and are defined as; ATH (10 – 50 pphr, Dicumyl Peroxide (0.50 -1.50 pphr, speed of mixer (40 – 70 rpm and mixing period (5 – 10 mins which were then varied accordingly to produce an overall 19 samples of SiR blends. The testing results were analyzed using statistical Design of Experiment (DOE by applying two level full factorial from Design Expert Software (v10 to discover the inter-correlation between the factors studied and benefaction of each factor in improving both surface resistivity and relative permittivity responses of produced SiR blends. The model analysis on surface resistivity shows the coefficient of determination R2 value of 88.72% while the one for relative permittivity shows R2 value of 82.34 %. Combination of both dependent variables had yielded an optimization suggestion for SiR formulation and processing strategy of ATH: 50 pphr, DCP: 0.50 pphr, mixing speed: 70 rpm and mixing period: 10 mins with the desirability level of 0.835. The optimized formulation had resulted in the production of SiR blend with the characteristic of surface resistivity of 1.02039x10^14 Ω/sq and relative permittivity of 4.0231, respectively. In conclusion, it can be

  7. Tungsten carbide modified high surface area carbon as fuel cell catalyst support

    Science.gov (United States)

    Shao, Minhua; Merzougui, Belabbes; Shoemaker, Krista; Stolar, Laura; Protsailo, Lesia; Mellinger, Zachary J.; Hsu, Irene J.; Chen, Jingguang G.

    Phase pure WC nanoparticles were synthesized on high surface area carbon black (800 m 2 g -1) by a temperature programmed reaction (TPR) method. The particle size of WC can be controlled under 30 nm with a relatively high coverage on the carbon surface. The electrochemical testing results demonstrated that the corrosion resistance of carbon black was improved by 2-fold with a surface modification by phase pure WC particles. However, the WC itself showed some dissolution under potential cycling. Based on the X-ray diffraction (XRD) and inductively coupled plasma (ICP) analysis, most of the WC on the surface was lost or transformed to oxides after 5000 potential cycles in the potential range of 0.65-1.2 V. The Pt catalyst supported on WC/C showed a slightly better ORR activity than that of Pt/C, with the Pt activity loss rate for Pt/WC/C being slightly slower compared to that of Pt/C. The performance and decay rate of Pt/WC/C were also evaluated in a fuel cell.

  8. Growth of Hierarchically Structured High-Surface Area Alumina on FeCrAl Alloy Wires

    Directory of Open Access Journals (Sweden)

    Chandni Rallan

    2013-01-01

    Full Text Available The formation of metastable alumina phases due to the oxidation of commercial FeCrAl alloy wires (0.5 mm thickness at various temperatures and time periods has been examined. Samples were isothermally oxidised in air using a thermogravimetric analyzer (TGA. The morphology of the oxidised samples was analyzed using an Electronic Scanning Electron Microscope (ESEM and X-ray on the surface analysis was done using an Energy Dispersive X-Ray (EDX analyzer. The technique of X-Ray Diffraction (XRD was used to characterize the phase of the oxide growth. The entire study showed that it was possible to grow high-surface area gamma alumina on the FeCrAl alloy wire surfaces when isothermally oxidised above 800°C over several hours.

  9. Surface properties of magnetic rigid disks for high-density data storage

    Science.gov (United States)

    Tsai, Hsiao-chu; Eltoukhy, Atef

    1990-05-01

    The chemical toughened glass is shown to be very safe for the disk-drive application based upon Weibull analyses of spin-to-break test data. Investigations revealed that frictional performance of glass disks can be correlated with two parameters (zero crossing and peak to valley) of the surface profile as measured by phase-shift interferometry. To compare the surface characteristics of glass with a conventional Al disk, the piezoelectrical baseline signals were measured by a glide head while flying steadily over a disk without asperity hits. The results showed that the glass disk caused less disturbance to the slider than the Al disk and can thus provide an intrinsically better surface for low-fly-height, high-density application.

  10. Temperature-dependent surface porosity of Nb2O5 under high-flux, low-energy He+ ion irradiation

    Science.gov (United States)

    Novakowski, T. J.; Tripathi, J. K.; Hosinski, G. M.; Joseph, G.; Hassanein, A.

    2016-01-01

    The present study reports on high-flux, low-energy He+ ion irradiation as a novel method of enhancing the surface porosity and surface area of naturally oxidized niobium (Nb). Our study shows that ion-irradiation-induced Nb surface micro- and nano-structures are highly tunable by varying the target temperature during ion bombardment. Mirror-polished Nb samples were irradiated with 100 eV He+ ions at a flux of 1.2 × 1021 ions m-2 s-1 to a total fluence of 4.3 × 1024 ions m-2 with simultaneous sample annealing in the temperature range of 773-1223 K to demonstrate the influence of sample temperature on the resulting Nb surface morphology. This surface morphology was primarily characterized using field-emission scanning electron microscopy (FE-SEM) and atomic force microscopy (AFM). Below 923 K, Nb surfaces form nano-scale tendrils and exhibit significant increases in surface porosity. Above 923 K, homogeneously populated nano-pores with an average diameter of ∼60 nm are observed in addition to a smaller population of sub-micron sized pores (up to ∼230 nm in diameter). Our analysis shows a significant reduction in surface pore number density and surface porosity with increasing sample temperature. High-resolution ex situ X-ray photoelectron spectroscopy (XPS) shows Nb2O5 phase in all of the ion-irradiated samples. To further demonstrate the length scales in which radiation-induced surface roughening occurs, optical reflectivity was performed over a spectrum of light between 200 and 1100 nm, showing a recovery of nano-scale surface damage at high sample temperatures.

  11. In situ synthesized 3D heterometallic metal-organic framework (MOF) as a high-energy-density material shows high heat of detonation, good thermostability and insensitivity.

    Science.gov (United States)

    Feng, Yaya; Liu, Xiangyu; Duan, Linqiang; Yang, Qi; Wei, Qing; Xie, Gang; Chen, Sanping; Yang, Xuwu; Gao, Shengli

    2015-02-07

    A reticular 3D heterometallic metal-organic framework (MOF), [Cu4Na(Mtta)5(CH3CN)]n () (N% = 40.08%), has been synthesized, using a 5-methyl tetrazole (Mtta) ligand formed from acetonitrile and azide, through in situ synthesis and structurally characterized by X-ray single crystal diffraction. The fluorescence spectra demonstrate that undergoes an interesting structural transformation in aqueous solution, yielding the compound [Cu4Na(Mtta)5H2O]n () as confirmed by (1)H NMR, IR and PXRD. Thermoanalysis showed that possesses excellent thermostability up to 335 °C. The calculated detonation properties and the sensitivity test illustrate that compound could be used as a potential explosive. In addition, the non-isothermal kinetics for were studied using the Kissinger and Ozawa-Doyle methods. The enthalpy of formation was obtained from the determination of the constant-volume combustion energy.

  12. A simple and highly effective process for the preparation of activated carbons with high surface area

    Energy Technology Data Exchange (ETDEWEB)

    Li Ying, E-mail: liyingjlu@163.com [College of Chemistry, Jilin University, Changchun 130012 (China); Ding Xuefeng; Guo Yupeng; Wang Lili; Rong Chunguang; Qu Yuning; Ma Xiaoyu [College of Chemistry, Jilin University, Changchun 130012 (China); Wang Zichen, E-mail: wangzc@jlu.edu.cn [College of Chemistry, Jilin University, Changchun 130012 (China)

    2011-06-15

    Highlights: {yields} High surface area activated carbon can be prepared by rice husk H{sub 3}PO{sub 4} without pretreatment. {yields} The characteristics of the activated carbon were greatly influenced by post-processing method. {yields} The lower SiO{sub 2} content of the activated carbons, the higher pore volume the carbons had. {yields} Some silica in rice husk reacted with H{sub 3}PO{sub 4} to form SiP{sub 2}O{sub 7} which could be removed by post-process. - Abstract: Activated carbons with high surface area were prepared by phosphoric acid as activation agent and rice husks as precursors. It was found that the characteristics of the activated carbons were influenced not only by the preparation but also by the post-processing method. The high surface area of the activated carbons was prepared under the optimum condition (50% H{sub 3}PO{sub 4} with impregnation ratio of 5:1, activation temperature of 500 deg. C, activation time of 0.5 h, wash water temperature of 100 deg. C). SiO{sub 2} content could affect the surface area of activated carbons, either. The lower SiO{sub 2} content of the activated carbons, the higher pore volume the carbons had. The SiO{sub 2} content was 11.2% when used the optimum condition. The explanation was that silicon element in rice husks reacted with H{sub 3}PO{sub 4} to form silicon phosphate (SiP{sub 2}O{sub 7}), and it could be proved further by X-ray diffraction analysis, SiP{sub 2}O{sub 7} could be removed by post-process.

  13. Black TiO2 nanotubes formed by high energy proton implantation show noble-metal-co-catalyst free photocatalytic H2-evolution

    CERN Document Server

    Liu, Ning; Zhou, Xuemei; Venkatesan, Umamaheswari; Hartmann, Martin; Mačković, Mirza; Nakajima, Tomohiko; Spiecker, Erdmann; Osvet, Andres; Frey, Lothar; Schmuki, Patrik

    2016-01-01

    We apply high-energy proton ion-implantation to modify TiO2 nanotubes selectively at their tops. In the proton-implanted region we observe the creation of intrinsic co-catalytic centers for photocatalytic H2-evolution. We find proton implantation to induce specific defects and a characteristic modification of the electronic properties not only in nanotubes but also on anatase single crystal (001) surfaces. Nevertheless, for TiO2 nanotubes a strong synergetic effect between implanted region (catalyst) and implant-free tube segment (absorber) can be obtained.

  14. Quantum interference of highly-dispersive surface plasmons (Conference Presentation)

    Science.gov (United States)

    Tokpanov, Yury S.; Fakonas, James S.; Atwater, Harry A.

    2016-09-01

    Previous experiments have shown that surface plasmon polaritons (SPPs) preserve their entangled state and do not cause measurable decoherence. However, essentially all of them were done using SPPs whose dispersion was in the linear "photon-like" regime. We report in this presentation on experiments showing how transition to "true-plasmon" non-linear dispersion regime, which occurs near SPP resonance frequency, will affect quantum coherent properties of light. To generate a polarization-entangled state we utilize type-I parametric down-conversion, occurring in a pair of non-linear crystals (BiBO), glued together and rotated by 90 degrees with respect to each other. For state projection measurements, we use a pair of polarizers and single-photon avalanche diode coincidence count detectors. We interpose a plasmonic hole array in the path of down-converted light before the polarizer. Without the hole array, we measure visibility V=99-100% and Bell's number S=2.81±0.03. To study geometrical effects we fabricated plasmonic hole arrays (gold on optically polished glass) with elliptical holes (axes are 190nm and 240nm) using focused ion beam. When we put this sample in our system we measured the reduction of visibility V=86±5% using entangled light. However, measurement using classical light gave exactly the same visibility; hence, this reduction is caused only by the difference in transmission coefficients of different polarizations. As samples with non-linear dispersion we fabricated two-layer (a-Si - Au) and three-layer (a-Si - Au - a-Si) structures on optically polished glass with different pitches and circular holes. The results of measurements with these samples will be discussed along with the theoretical investigations.

  15. Multitechnique characterisation of 304L surface states oxidised at high temperature in steam and air atmospheres

    Energy Technology Data Exchange (ETDEWEB)

    Mamede, Anne-Sophie, E-mail: anne-sophie.mamede@ensc-lille.fr [University Lille, CNRS, ENSCL, Centrale Lille, University Artois, UMR 8181 – UCCS – Unité de Catalyse et Chimie du Solide, F-59000 Lille (France); Nuns, Nicolas, E-mail: nicolas.nuns@univ-lille1.fr [University Lille, CNRS, ENSCL, Centrale Lille, University Artois, UMR 8181 – UCCS – Unité de Catalyse et Chimie du Solide, F-59000 Lille (France); Cristol, Anne-Lise, E-mail: anne-lise.cristol@ec-lille.fr [University Lille, CNRS, Centrale Lille, Arts et Métiers Paris Tech, FRE 3723 – LML – Laboratoire de Mécanique de Lille, F-59000 Lille (France); Cantrel, Laurent, E-mail: laurent.cantrel@irsn.fr [Institut de Radioprotection et de Sûreté Nucléaire, PSN-RES, Cadarache, Saint Paul lez Durance, 13115 (France); Laboratoire de Recherche Commun IRSN-CNRS-Lille 1: «Cinétique Chimique, Combustion, Réactivité» (C3R), Cadarache, Saint Paul lez Durance, 13115 (France); Souvi, Sidi, E-mail: sidi.souvi@irsn.fr [Institut de Radioprotection et de Sûreté Nucléaire, PSN-RES, Cadarache, Saint Paul lez Durance, 13115 (France); Laboratoire de Recherche Commun IRSN-CNRS-Lille 1: «Cinétique Chimique, Combustion, Réactivité» (C3R), Cadarache, Saint Paul lez Durance, 13115 (France); and others

    2016-04-30

    Graphical abstract: - Highlights: • Mutitechnique characterisation of oxidised 304L. • Oxidation at high temperature under steam and air conditions of 304L stainless steel. • Chromium and manganese oxides formed in the outer layer. • Oxide profiles differ in air or steam atmosphere. - Abstract: In case of a severe accident occurring in a nuclear reactor, surfaces of the reactor coolant system (RCS), made of stainless steel (304L) rich in Cr (>10%) and Ni (8–12%), are oxidised. Fission products (FPs) are released from melt fuel and flow through the RCS. A part of them is deposited onto surfaces either by vapour condensation or by aerosol deposition mechanisms. To be able to understand the nature of interactions between these FPs and the RCS surfaces, a preliminary step is to characterize the RSC surface states in steam and air atmosphere at high temperatures. Pieces of 304L stainless steel have been treated in a flow reactor at two different temperatures (750 °C and 950 °C) for two different exposition times (24 h and 72 h). After surfaces analysing by a unique combination of surface analysis techniques (XPS, ToF-SIMS and LEIS), for 304L, the results show a deep oxide scale with multi layers and the outer layer is composed of chromium and manganese oxides. Oxide profiles differ in air or steam atmosphere. Fe{sub 2}O{sub 3} oxide is observed but in minor proportion and in all cases no nickel is detected near the surface. Results obtained are discussed and compared with the literature data.

  16. Development of high resolution land surface parameters for the Community Land Model

    Directory of Open Access Journals (Sweden)

    Y. Ke

    2012-06-01

    Full Text Available There is a growing need for high-resolution land surface parameters as land surface models are being applied at increasingly higher spatial resolution offline as well as in regional and global models. The default land surface parameters for the most recent version of the Community Land Model (i.e. CLM 4.0 are at 0.5° or coarser resolutions, released with the model from the National Center for Atmospheric Research (NCAR. Plant Functional Types (PFTs, vegetation properties such as Leaf Area Index (LAI, Stem Area Index (SAI, and non-vegetated land covers were developed using remotely-sensed datasets retrieved in late 1990's and the beginning of this century. In this study, we developed new land surface parameters for CLM 4.0, specifically PFTs, LAI, SAI and non-vegetated land cover composition, at 0.05° resolution globally based on the most recent MODIS land cover and improved MODIS LAI products. Compared to the current CLM 4.0 parameters, the new parameters produced a decreased coverage by bare soil and trees, but an increased coverage by shrub, grass, and cropland. The new parameters result in a decrease in global seasonal LAI, with the biggest decrease in boreal forests; however, the new parameters also show a large increase in LAI in tropical forest. Differences between the new and the current parameters are mainly caused by changes in the sources of remotely sensed data and the representation of land cover in the source data. The new high-resolution land surface parameters have been used in a coupled land-atmosphere model (WRF-CLM applied to the western US to demonstrate their use in high-resolution modeling. Future work will include global offline CLMsimulations to examine the impacts of source data resolution and subsequent land parameter changes on simulated land surface processes.

  17. Examination of Poststroke Alteration in Motor Unit Firing Behavior Using High-Density Surface EMG Decomposition.

    Science.gov (United States)

    Li, Xiaoyan; Holobar, Ales; Gazzoni, Marco; Merletti, Roberto; Rymer, William Zev; Zhou, Ping

    2015-05-01

    Recent advances in high-density surface electromyogram (EMG) decomposition have made it a feasible task to discriminate single motor unit activity from surface EMG interference patterns, thus providing a noninvasive approach for examination of motor unit control properties. In the current study, we applied high-density surface EMG recording and decomposition techniques to assess motor unit firing behavior alterations poststroke. Surface EMG signals were collected using a 64-channel 2-D electrode array from the paretic and contralateral first dorsal interosseous (FDI) muscles of nine hemiparetic stroke subjects at different isometric discrete contraction levels between 2 to 10 N with a 2 N increment step. Motor unit firing rates were extracted through decomposition of the high-density surface EMG signals and compared between paretic and contralateral muscles. Across the nine tested subjects, paretic FDI muscles showed decreased motor unit firing rates compared with contralateral muscles at different contraction levels. Regression analysis indicated a linear relation between the mean motor unit firing rate and the muscle contraction level for both paretic and contralateral muscles (p < 0.001), with the former demonstrating a lower increment rate (0.32 pulses per second (pps)/N) compared with the latter (0.67 pps/N). The coefficient of variation (averaged over the contraction levels) of the motor unit firing rates for the paretic muscles (0.21 ± 0.012) was significantly higher than for the contralateral muscles (0.17 ± 0.014) (p < 0.05). This study provides direct evidence of motor unit firing behavior alterations poststroke using surface EMG, which can be an important factor contributing to hemiparetic muscle weakness.

  18. Surface chemical properties of novel high surface area solids synthesized from coal fly ash

    CSIR Research Space (South Africa)

    Pretorius, PJ

    2003-07-23

    Full Text Available to the presence of =AlOH- and =SiOH-type surface groups. Surface protonation constants for the various solids (unmodified ash, base-modified ash, and acid-etched zeolitic product) are reported. Metal sorption studies were performed for cadmium and copper...

  19. Rough surface Au@Ag core-shell nanoparticles to fabricating high sensitivity SERS immunochromatographic sensors.

    Science.gov (United States)

    Fu, Qiangqiang; Liu, Hongwu Liu; Wu, Ze; Liu, An; Yao, Cuize; Li, Xiuqing; Xiao, Wei; Yu, Shiting; Luo, Zhi; Tang, Yong

    2015-11-14

    Immunochromatographic sensors (ICSs) are inexpensive, simple, portable, and robust, thus making ICSs commonplace in clinical diagnoses, food testing, and environmental monitoring. However, commonly used gold nanoparticles (AuNPs) ICSs have low sensitivity. Therefore, we developed highly sensitive surface enhanced Raman scattering (SERS) ICSs. To enhance the sensitivity of SERS ICSs, rough surface core-shell Au@Ag nanoparticles (RSAu@AgNPs) were prepared by coating silver on the surface of gold nanoflowers (AuNFs). Then these nanoparticles were used as SERS substrate in the SERS ICSs, after which the SERS ICSs were implemented to detect haemoglobin and heavy metal cadmium ion (Cd(2+)). The limit of detection (LOD) of the SERS ICSs for detecting haemoglobin was 8 ng/mL, and the linear range of the SERS ICSs was from 31.3 to 2000 ng/mL. The LOD of the SERS ICSs for detecting Cd(2+) was 0.05 ng/mL and the linear analysis range was from 0.05 to 25 ng/mL. The cross reactivity of the SERS ICSs was studied and results showed that the SERS ICSs exhibited highly specific for detection of haemoglobin and Cd(2+), respectively. The SERS ICSs were then used to detect haemoglobin (spiked in serum and in stool) and Cd(2+) (spiked in tap water, river water, and soil leaching water), and the results showed high recovery. These characteristics indicated that SERS ICSs were ideal tools for clinical diagnosis and environmental pollution monitoring.

  20. Highly Nonlinear Luminescence Induced by Gold Nanoparticles on Glass Surfaces with Continuous-Wave Laser Illumination

    CERN Document Server

    Wu, Yong; Toro, Ligia; Stefani, Enrico

    2015-01-01

    We report on highly nonlinear luminescence being observed from individual spherical gold nanoparticles immobilized on a borosilicate glass surface and illuminated by continuous-wave (CW) lasers with relatively low power. The nonlinear luminescence shows optical super-resolution beyond the diffraction limit in three dimensions compared to the scatting of the excitation laser light. The luminescence intensity from most nanoparticles is proportional to the 5th--7th power of the excitation laser power and has wide excitation and emission spectra across the visible wavelength range. Strong nonlinear luminescence is only observed near the glass surface. High optical nonlinearity excited by low CW laser power is related to a long-lived dark state of the gold nanoparticles, where the excitation light is strongly absorbed. This phenomenon has potential biological applications in super-resolution and deep tissue imaging.

  1. Method for the preparation of high surface area high permeability carbons

    Science.gov (United States)

    Lagasse, R.R.; Schroeder, J.L.

    1999-05-11

    A method for preparing carbon materials having high surface area and high macropore volume to provide high permeability. These carbon materials are prepared by dissolving a carbonizable polymer precursor, in a solvent. The solution is cooled to form a gel. The solvent is extracted from the gel by employing a non-solvent for the polymer. The non-solvent is removed by critical point drying in CO{sub 2} at an elevated pressure and temperature or evaporation in a vacuum oven. The dried product is heated in an inert atmosphere in a first heating step to a first temperature and maintained there for a time sufficient to substantially cross-link the polymer material. The cross-linked polymer material is then carbonized in an inert atmosphere. 3 figs.

  2. Method for the preparation of high surface area high permeability carbons

    Energy Technology Data Exchange (ETDEWEB)

    Lagasse, Robert R. (Albuquerque, NM); Schroeder, John L. (Albuquerque, NM)

    1999-05-11

    A method for preparing carbon materials having high surface area and high macropore volume to provide high permeability. These carbon materials are prepared by dissolving a carbonizable polymer precursor, in a solvent. The solution is cooled to form a gel. The solvent is extracted from the gel by employing a non-solvent for the polymer. The non-solvent is removed by critical point drying in CO.sub.2 at an elevated pressure and temperature or evaporation in a vacuum oven. The dried product is heated in an inert atmosphere in a first heating step to a first temperature and maintained there for a time sufficient to substantially cross-link the polymer material. The cross-linked polymer material is then carbonized in an inert atmosphere.

  3. Large surface radiative forcing from topographic blowing snow residuals measured in the High Arctic at Eureka

    Directory of Open Access Journals (Sweden)

    G. Lesins

    2009-03-01

    Full Text Available Ice crystals, also known as diamond dust, are suspended in the boundary layer air under clear sky conditions during most of the Arctic winter in Northern Canada. Occasionally ice crystal events can produce significantly thick layers with optical depths in excess of 2.0 even in the absence of liquid water clouds. Four case studies of high optical depth ice crystal events at Eureka in the Nunavut Territory of Canada during the winter of 2006/07 are presented. They show that the measured ice crystal surface infrared downward radiative forcing ranged from 8 to 36 W m−2 in the wavelength band from 5.6 to 20 μm for 532 nm optical depths ranging from 0.2 to 1.7. MODIS infrared and visible images and the operational radiosonde wind profile were used to show that these high optical depth events were caused by surface snow being blown off 600 to 800 m high mountain ridges about 20 to 30 km North-West of Eureka and advected by the winds towards Eureka as they settled towards the ground within the highly stable boundary layer. This work presents the first study that demonstrates the important role that surrounding topography plays in determining the occurrence of high optical depth ice crystal events from residual blowing snow that becomes a source of boundary layer ice crystals distinct from the classical diamond dust phenomenon.

  4. Tool-path planning for free-form surface high-speed high-resolution machining using torus cutter

    Institute of Scientific and Technical Information of China (English)

    WANG Yu-han; LI Ru-qiong; WU Zu-yu; CHEN Zhao-neng

    2006-01-01

    In CNC machining, two essential components decide the accuracy and machining time for a sculptured surface: one is the step-size interval, the other is the tool-path interval. Due to the limitation of the conventional method for calculating the tool-path interval, it cannot satisfy the machining requirement for highspeed and high-resolution machining. Accordingly, for high-speed and high-resolution machining, the current study proposes a new tool-path interval algorithm, plus a variable step-size algorithm for NURBS. Furthermore,a new type cutter, which can improve the cutting efficiency, is investigated in the paper. The transversal equation of the torus cutter onto the flat plan is given in this paper. The tool-path interval is calculated with the transversal equation and the proposed algorithm. The illustrated example shows that the redundant tool paths can be reduced because an accurate tool-path interval could be calculated.

  5. Hydrophobic modification on surface of chitin sponges for highly effective separation of oil.

    Science.gov (United States)

    Duan, Bo; Gao, Huimin; He, Meng; Zhang, Lina

    2014-11-26

    A highly hydrophobic and oleophilic chitin sponge was synthesized, for the first time, via a freeze-dried method and then by using a thermal chemical vapor deposition of methyltrichlorosilane (MTCS) at different relative humidity. Fourier-transform infrared, energy-dispersive X-ray spectra, and scanning electron microscopy confirmed that the silanization occurred on the pore wall surface of the chitin sponge. The MTCS-coated chitin sponge had interconnected open-cell structures with the average pore size from 20 to 50 μm, and the MTCS nanofilaments immobilized on the chitin matrix, leading to the high hydrophobicity, as a result of the existence of a solid/air composite rough surface. Cyclic compression test indicated that the hydrophobic chitin sponges exhibited excellent elasticity and high mechanical durability. The sponges could efficiently collect organics both on the surface and bottom from the water with the highest 58 times of their own weight absorption capacities through the combination of the particular wettability and great porosity. Furthermore, the biodegradation kinetics of the chitin sponge forecasted that the chitin could be completely biodegraded within 32 days by the microorganisms in the soil. This work provided a new pathway to prepare the chitin-based materials for highly effective removal of oil from water, showing potential application in the pollutant remediation field.

  6. Mesoscale climatic simulation of surface air temperature cooling by highly reflective greenhouses in SE Spain.

    Science.gov (United States)

    Campra, Pablo; Millstein, Dev

    2013-01-01

    A long-term local cooling trend in surface air temperature has been monitored at the largest concentration of reflective greenhouses in the world, at the Province of Almeria, SE Spain, associated with a dramatic increase in surface albedo in the area. The availability of reliable long-term climatic field data at this site offers a unique opportunity to test the skill of mesoscale meteorological models describing and predicting the impacts of land use change on local climate. Using the Weather Research and Forecast (WRF) mesoscale model, we have run a sensitivity experiment to simulate the impact of the observed surface albedo change on monthly and annual surface air temperatures. The model output showed a mean annual cooling of 0.25 °C associated with a 0.09 albedo increase, and a reduction of 22.8 W m(-2) of net incoming solar radiation at surface. Mean reduction of summer daily maximum temperatures was 0.49 °C, with the largest single-day decrease equal to 1.3 °C. WRF output was evaluated and compared with observations. A mean annual warm bias (MBE) of 0.42 °C was estimated. High correlation coefficients (R(2) > 0.9) were found between modeled and observed values. This study has particular interest in the assessment of the potential for urban temperature cooling by cool roofs deployment projects, as well as in the evaluation of mesoscale climatic models performance.

  7. Epithermal Neutron Evidence for a Diurnal Surface Hydration Process in the Moon's High Latitudes

    Science.gov (United States)

    McClanahan, T. P.; Mitrofanov, I. G.; Boynton, W. V.; Chin, G.; Parsons, A.; Starr, R. D.; Evans, L. G.; Sanin, A.; Litvak, M.; Livengood, T.

    2015-01-01

    We report evidence from epithermal neutron flux observations that show that the Moon's high latitude surfaces are being actively hydrated, dehydrated and rehydrated in a diurnal cycle. The near-surface hydration is indicated by an enhanced suppression of the lunar epithermal neutron leakage flux on the dayside of the dawn terminator on poleward-facing slopes (PFS). At 0600 to 0800 local-time, hydrogen concentrations within the upper 1 meter of PFS are observed to be maximized relative to equivalent equator-facing slopes (EFS). During the lunar day surface hydrogen concentrations diminish towards dusk and then rebuild overnight. Surface hydration is determined by differential comparison of the averaged EFS to PFS epithermal neutron count rates above +/- 75 deg latitude. At dawn the contrast bias towards PFS is consistent with at least 15 to 25 parts-per-million (ppm) hydrogen that dissipates by dusk. We review several lines of evidence derived from temperature and epithermal neutron data by a correlated analysis of observations from the Lunar Reconnaissance Orbiter's (LRO) Lunar Exploration Neutron Detector (LEND) that were mapped as a function of lunar local-time, Lunar Observing Laser Altimeter (LOLA) topography and Diviner (DLRE) surface temperature.

  8. Aeroacoustic Study of a High-Fidelity Aircraft Model. Part 2; Unsteady Surface Pressures

    Science.gov (United States)

    Khorrami, Mehdi R.; Neuhart, Danny H.

    2012-01-01

    In this paper, we present unsteady surface pressure measurements for an 18%-scale, semi-span Gulfstream aircraft model. This high-fidelity model is being used to perform detailed studies of airframe noise associated with main landing gear, flap components, and gear-flap interaction noise, as well as to evaluate novel noise reduction concepts. The aerodynamic segment of the tests, conducted in the NASA Langley Research Center 14- by 22-Foot Subsonic Tunnel, was completed in November 2010. To discern the characteristics of the surface pressure fluctuations in the vicinity of the prominent noise sources, unsteady sensors were installed on the inboard and outboard flap edges, and on the main gear wheels, struts, and door. Various configurations were tested, including flap deflections of 0?, 20?, and 39?, with and without the main landing gear. The majority of unsteady surface pressure measurements were acquired for the nominal landing configuration where the main gear was deployed and the flap was deflected 39?. To assess the Mach number variation of the surface pressure amplitudes, measurements were obtained at Mach numbers of 0.16, 0.20, and 0.24. Comparison of the unsteady surface pressures with the main gear on and off shows significant interaction between the gear wake and the inboard flap edge, resulting in higher amplitude fluctuations when the gear is present.

  9. Exploring site-specific chemical interactions at surfaces: a case study on highly ordered pyrolytic graphite

    Science.gov (United States)

    Dagdeviren, Omur E.; Götzen, Jan; Altman, Eric I.; Schwarz, Udo D.

    2016-12-01

    A material’s ability to interact with approaching matter is governed by the structural and chemical nature of its surfaces. Tailoring surfaces to meet specific needs requires developing an understanding of the underlying fundamental principles that determine a surface’s reactivity. A particularly insightful case occurs when the surface site exhibiting the strongest attraction changes with distance. To study this issue, combined noncontact atomic force microscopy and scanning tunneling microscopy experiments have been carried out, where the evolution of the local chemical interaction with distance leads to a contrast reversal in the force channel. Using highly ordered pyrolytic graphite surfaces and metallic probe tips as a model system, we find that at larger tip-sample distances, carbon atoms exhibit stronger attractions than hollow sites while upon further approach, hollow sites become energetically more favorable. For the tunneling current that is recorded at large tip-sample separations during acquisition of a constant-force image, the contrast is dominated by the changes in tip-sample distance required to hold the force constant (‘cross-talk’) at smaller separations the contrast turns into a convolution of this cross-talk and the local density of states. Analysis shows that the basic factors influencing the force channel contrast reversal are locally varying decay lengths and an onset of repulsive forces that occurs for distinct surface sites at different tip-sample distances. These findings highlight the importance of tip-sample distance when comparing the relative strength of site-specific chemical interactions.

  10. Improve oxidation resistance at high temperature by nanocrystalline surface layer.

    Science.gov (United States)

    Xia, Z X; Zhang, C; Huang, X F; Liu, W B; Yang, Z G

    2015-08-13

    An interesting change of scale sequence occurred during oxidation of nanocrystalline surface layer by means of a surface mechanical attrition treatment. The three-layer oxide structure from the surface towards the matrix is Fe3O4, spinel FeCr2O4 and corundum (Fe,Cr)2O3, which is different from the typical two-layer scale consisted of an Fe3O4 outer layer and an FeCr2O4 inner layer in conventional P91 steel. The diffusivity of Cr, Fe and O is enhanced concurrently in the nanocrystalline surface layer, which causes the fast oxidation in the initial oxidation stage. The formation of (Fe,Cr)2O3 inner layer would inhabit fast diffusion of alloy elements in the nanocrystalline surface layer of P91 steel in the later oxidation stage, and it causes a decrease in the parabolic oxidation rate compared with conventional specimens. This study provides a novel approach to improve the oxidation resistance of heat resistant steel without changing its Cr content.

  11. Effects of surface treating methods of high-strength carbon fibers on interfacial properties of epoxy resin matrix composite

    Energy Technology Data Exchange (ETDEWEB)

    Ma, Quansheng; Gu, Yizhuo, E-mail: benniegu@buaa.edu.cn; Li, Min; Wang, Shaokai; Zhang, Zuoguang

    2016-08-30

    Highlights: • Effects of surface treating on T700 grade high strength carbon fiber were discussed. • The fiber surface roughness, surface energy and chemical properties are analyzed. • The surface treating significantly affect the properties of carbon fiber. • The composite with electrolysis and sizing-fiber has the highest mechanical properties. - Abstract: This paper aims to study the effects of surface treating methods, including electrolysis of anodic oxidation, sizing and heat treatment at 200 °C, on physical and chemical properties of T700 grade high-strength carbon fiber GQ4522. The fiber surface roughness, surface energy and chemical properties were analyzed for different treated carbon fibers, using atom force microscopy, contact angle, Fourier transformed infrared and X-ray photoelectron spectroscopy, respectively. The results show that the adopted surface treating methods significantly affect surface roughness, surface energy and active chemical groups of the studied carbon fibers. Electrolysis and sizing can increase the roughness, surface energy and chemical groups on surface, while heat treatment leads to decreases in surface energy and chemical groups due to chemical reaction of sizing. Then, unidirectional epoxy 5228 matrix composite laminates were prepared using different treated GQ4522 fibers, and interlaminar shear strength and flexural property were measured. It is revealed that the composite using electrolysis and sizing-fiber has the strongest interfacial bonding strength, indicating the important roles of the two treating processes on interfacial adhesion. Moreover, the composite using heat-treating fiber has lower mechanical properties, which is attributed to the decrease of chemical bonding between fiber surface and matrix after high temperature treatment of fiber.

  12. Synthetic microfluidic paper: high surface area and high porosity polymer micropillar arrays.

    Science.gov (United States)

    Hansson, Jonas; Yasuga, Hiroki; Haraldsson, Tommy; van der Wijngaart, Wouter

    2016-01-21

    We introduce Synthetic Microfluidic Paper, a novel porous material for microfluidic applications that consists of an OSTE polymer that is photostructured in a well-controlled geometry of slanted and interlocked micropillars. We demonstrate the distinct benefits of Synthetic Microfluidic Paper over other porous microfluidic materials, such as nitrocellulose, traditional paper and straight micropillar arrays: in contrast to straight micropillar arrays, the geometry of Synthetic Microfluidic Paper was miniaturized without suffering capillary collapse during manufacturing and fluidic operation, resulting in a six-fold increased internal surface area and a three-fold increased porous fraction. Compared to commercial nitrocellulose materials for capillary assays, Synthetic Microfluidic Paper shows a wider range of capillary pumping speed and four times lower device-to-device variation. Compared to the surfaces of the other porous microfluidic materials that are modified by adsorption, Synthetic Microfluidic Paper contains free thiol groups and has been shown to be suitable for covalent surface chemistry, demonstrated here for increasing the material hydrophilicity. These results illustrate the potential of Synthetic Microfluidic Paper as a porous microfluidic material with improved performance characteristics, especially for bioassay applications such as diagnostic tests.

  13. High surface area stainless steel brushes as cathodes in microbial electrolysis cells.

    Science.gov (United States)

    Call, Douglas F; Merrill, Matthew D; Logan, Bruce E

    2009-03-15

    Microbial electrolysis cells (MECs) are an efficient technology for generating hydrogen gas from organic matter, but alternatives to precious metals are needed for cathode catalysts. We show here that high surface area stainless steel brush cathodes produce hydrogen at rates and efficiencies similar to those achieved with platinum-catalyzed carbon cloth cathodes in single-chamber MECs. Using a stainless steel brush cathode with a specific surface area of 810 m2/m3, hydrogen was produced at a rate of 1.7 +/- 0.1 m3-H2/m3-d (current density of 188 +/- 10 A/m3) at an applied voltage of 0.6 V. The energy efficiency relative to the electrical energy input was 221 +/- 8%, and the overall energy efficiency was 78 +/- 5% based on both electrical energy and substrate utilization. These values compare well to previous results obtained using platinum on flat carbon cathodes in a similar system. Reducing the cathode surface area by 75% decreased performance from 91 +/- 3 A/m3 to 78 +/- 4 A/m3. A brush cathode with graphite instead of stainless steel and a specific surface area of 4600 m2/m3 generated substantially less current (1.7 +/- 0.0 A/m3), and a flat stainless steel cathode (25 m2/m3) produced 64 +/- 1 A/m3, demonstrating that both the stainless steel and the large surface area contributed to high current densities. Linear sweep voltammetry showed that the stainless steel brush cathodes both reduced the overpotential needed for hydrogen evolution and exhibited a decrease in overpotential over time as a result of activation. These results demonstrate for the first time that hydrogen production can be achieved at rates comparable to those with precious metal catalysts in MECs without the need for expensive cathodes.

  14. Assessment Of Surface-Catalyzed Reaction Products From High Temperature Materials In Plasmas

    Science.gov (United States)

    Allen, Luke Daniel

    Current simulations of atmospheric entry into both Mars and Earth atmospheres for the design of thermal protections systems (TPS) typically invoke conservative assumptions regarding surface-catalyzed recombination and the amount of energy deposited on the surface. The need to invoke such assumptions derives in part from lack of adequate experimental data on gas-surface interactions at trajectory relevant conditions. Addressing this issue, the University of Vermont's Plasma Test and Diagnostics Laboratory has done extensive work to measure atomic specie consumption by measuring the concentration gradient over various material surfaces. This thesis extends this work by attempting to directly diagnose molecular species production in air plasmas. A series of spectral models for the A-X and B-X systems of nitric oxide (NO), and the B-X system of boron monoxide (BO) have been developed. These models aim to predict line positions and strengths for the respective molecules in a way that is best suited for the diagnostic needs of the UVM facility. From the NO models, laser induced fluorescence strategies have been adapted with the intent of characterizing the relative quantity and thermodynamic state of NO produced bysurface-catalyzed recombination, while the BO model adds a diagnostic tool for the testing of diboride-based TPS materials. Boundary layer surveys of atomic nitrogen and NO have been carried out over water-cooled copper and nickel surfaces in air/argon plasmas. Translation temperatures and relative number densities throughout the boundary layer are reported. Additional tests were also conducted over a water-cooled copper surface to detect evidence of highly non-equilibrium effects in the form of excess population in elevated vibrational levels of the A-X system of NO. The tests showed that near the sample surface there is a much greater population in the upsilon'' = 1ground state than is predicted by a Boltzmann distribution.

  15. Surface structure of imidazolium-based ionic liquids: Quantitative comparison between simulations and high-resolution RBS measurements

    Science.gov (United States)

    Nakajima, Kaoru; Nakanishi, Shunto; Lísal, Martin; Kimura, Kenji

    2016-03-01

    Elemental depth profiles of 1-alkyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide ([CnMIM][TFSI], n = 4, 6, 8) are measured using high-resolution Rutherford backscattering spectroscopy (HRBS). The profiles are compared with the results of molecular dynamics (MD) simulations. Both MD simulations and HRBS measurements show that the depth profiles deviate from the uniform stoichiometric composition in the surface region, showing preferential orientations of ions at the surface. The MD simulations qualitatively reproduce the observed HRBS profiles but the agreement is not satisfactory. The observed discrepancy is ascribed to the capillary waves. By taking account of the surface roughness induced by the capillary waves, the agreement becomes almost perfect.

  16. Development and Testing of High Surface Area Iridium Anodes for Molten Oxide Electrolysis

    Science.gov (United States)

    Shchetkovskiy, Anatoliy; McKechnie, Timothy; Sadoway, Donald R.; Paramore, James; Melendez, Orlando; Curreri, Peter A.

    2010-01-01

    Processing of lunar regolith into oxygen for habitat and propulsion is needed to support future space missions. Direct electrochemical reduction of molten regolith is an attractive method of processing, because no additional chemical reagents are needed. The electrochemical processing of molten oxides requires high surface area, inert anodes. Such electrodes need to be structurally robust at elevated temperatures (1400-1600?C), be resistant to thermal shock, have good electrical conductivity, be resistant to attack by molten oxide (silicate), be electrochemically stable and support high current density. Iridium with its high melting point, good oxidation resistance, superior high temperature strength and ductility is the most promising candidate for anodes in high temperature electrochemical processes. Several innovative concepts for manufacturing such anodes by electrodeposition of iridium from molten salt electrolyte (EL-Form? process) were evaluated. Iridium electrodeposition to form of complex shape components and coating was investigated. Iridium coated graphite, porous iridium structure and solid iridium anodes were fabricated. Testing of electroformed iridium anodes shows no visible degradation. The result of development, manufacturing and testing of high surface, inert iridium anodes will be presented.

  17. A high sensitivity wireless mass-loading surface acoustic wave DNA biosensor

    Science.gov (United States)

    Cai, Hua-Lin; Yang, Yi; Zhang, Yi-Han; Zhou, Chang-Jian; Guo, Cang-Ran; Liu, Jing; Ren, Tian-Ling

    2014-03-01

    In this paper, a surface acoustic wave (SAW) biosensor with gold delay area on LiNbO3 substrate detecting DNA sequences is proposed. By well-designed device parameters of the SAW sensor, it achieves a high performance for highly sensitive detection of target DNA. In addition, an effective biological treatment method for DNA immobilization and abundant experimental verification of the sensing effect have made it a reliable device in DNA detection. The loading mass of the probe and target DNA sequences is obtained from the frequency shifts, which are big enough in this work due to an effective biological treatment. The experimental results show that the biosensor has a high sensitivity of 1.2 pg/ml/Hz and high selectivity characteristic is also verified by the few responses of other substances. In combination with wireless transceiver, we develop a wireless receiving and processing system that can directly display the detection results.

  18. Preparation and Characterization of Highly Spherical Silica-titania Aerogel Beads with High Surface Area

    Directory of Open Access Journals (Sweden)

    YU Yu-xi

    2017-02-01

    Full Text Available The silica-titania aerogel beads were synthesized through sol-gel reaction followed by supercritical drying, in which TEOS and TBT as co-precursors, EtOH as solvents, HAC and NH3·H2O as catalysts. The as-prepared aerogel beads were characterized by SEM,TEM,XRD,FT-IR,TG-DTA and nitrogen adsorption-desorption. The results indicate that the diameter distribution of beads are between 1-8mm, the average diameter of beads is 3.5mm. The aerogel beads have nanoporous network structure with high specific surface area of 914.5m2/g, and the TiO2 particles are distributed in the aerogel uniformly, which keep the anatase crystal under high temperature.

  19. High Throughput Spectroscopic Catalyst Screening via Surface Plasmon Spectroscopy

    Science.gov (United States)

    2014-05-10

    transfer from the Pt to gold particles. Below we pictorially summarise how we have tried to use surface plasmon spectroscopy to study H2 interactions with...2014). 3. PI Mulvaney presented some of this work at an invied talk at the ACS Conference in Dallas in March 2014 and also to groups at

  20. Potential and Kinetic Electron Emissions from HOPG Surface Irradiated by Highly Charged Xenon and Neon Ions

    Institute of Scientific and Technical Information of China (English)

    WANG Yu-Yu; ZHAO Yong-Tao; SUN Jian-Rong; LI De-Hui; QAYYUM Abdul; LI Jin-Yu; WANG Ping-Zhi; XIAO Guo-Qing

    2011-01-01

    Highly charged 129 Xeq+ (q =10-30) and 40Neq+ (q =4-8) ion-induced secondary electron emissions on the surface of highly oriented pyrolytic graphite (HOPG) are reported. The total secondary electron yield is measured as a function of the potential energy of incident ions. The experimental data are used to separate contributions of kinetic and potential electron yields. Our results show that about 4.5% and 13.2% of ion's potential energies are consumed in potential electron emission due to different Xeq+-HOPG and Neq+-HOPG combinations. A simple formula is introduced to estimate the fraction of ion's potential energy for potential electron emission.%@@ Highly charged 129 Xeq+(q =10-30) and 40Neq+(q =4-8) ion-induced secondary electron emissions on the surface of highly oriented pyrolytic graphite(HOPG) are reported.The total secondary electron yield is measured as a function of the potential energy of incident ions.The experimental data are used to separate contributions of kinetic and potential electron yields.Our results show that about 4.5% and 13.2% of ion's potential energies are consumed in potential electron emission due to different Xeq+-HOPG and Neq+-HOPG combinations.A simple formula is introduced to estimate the fraction of ion's potential energy for potential electron emission.

  1. Estimation of surface charges on dielectric materials for high power rf windows

    Energy Technology Data Exchange (ETDEWEB)

    Michizono, Shinichiro, E-mail: shinichiro.michizono@kek.jp [High Energy Accelerator Research Organization (KEK), Tsukuba, Ibaraki 305-0801 (Japan); Saito, Yoshio [High Energy Accelerator Research Organization (KEK), Tsukuba, Ibaraki 305-0801 (Japan); Suharyanto [Faculty of Engineering, Gadjah Mada University, Yogyakarta 55284 (Indonesia); Yamano, Yasushi; Kobayashi, Shinichi [Faculty of Engineering, Saitama University, Saitama 338-8570 (Japan)

    2009-11-30

    The surface discharges observed at rf windows and vacuum circuit breakers (VCBs) are one of the difficulties faced when developing high-power rf windows or compact VCBs. The surface discharge is considered to take place due to the release of the surface charges. Despite the importance of the surface charging/discharging, these phenomena have not been well evaluated. In this paper, the surface charges are estimated using the multipulse method, where electron beam irradiates a sample up to the saturation condition of surface charges. The amount of surface charges on alumina and TiN coated alumina are compared and the charging mechanism is discussed.

  2. Impact of high-resolution sea surface temperature, emission spikes and wind on simulated surface ozone in Houston, Texas during a high ozone episode

    Science.gov (United States)

    Pan, Shuai; Choi, Yunsoo; Jeon, Wonbae; Roy, Anirban; Westenbarger, David A.; Kim, Hyun Cheol

    2017-03-01

    Model-measurement comparisons for surface ozone often show significant error, which could be attributed to problems in meteorology and emissions fields. A WRF-SMOKE-CMAQ air quality modeling system was used to investigate the contributions of these inputs. In this space, a base WRF run (BASE) and a WRF run initializing with NOAA GOES satellite sea surface temperature (SST) (SENS) were performed to clarify the impact of high-resolution SST on simulated surface ozone (O3) over the Greater Houston area during 25 September 2013, corresponding to the high O3 episode during the NASA DISCOVER-AQ Texas campaign. The SENS case showed reduced land-sea thermal contrast during early morning hours due to 1-2 °C lower SST over water bodies. The lowered SST reduced the model wind speed and slowed the dilution rate. These changes led to a simulated downwind O3 change of ∼5 ppb near the area over land with peak simulated afternoon O3. However, the SENS case still under-predicted surface O3 in urban and industrial areas. Episodic flare emissions, dry sunny postfrontal stagnated conditions, and land-bay/sea breeze transitions could be the potential causes of the high O3. In order to investigate the additional sources of error, three sensitivity simulations were performed for the high ozone time period. These involved adjusted emissions, adjusted wind fields, and both adjusted emissions and winds. These scenarios were superimposed on the updated SST (SENS) case. Adjusting NOx and VOC emissions using simulated/observed ratios improved correlation and index of agreement (IOA) for NOx from 0.48 and 0.55 to 0.81 and 0.88 respectively, but still reported spatial misalignment of afternoon O3 hotspots. Adjusting wind fields to represent morning weak westerly winds and afternoon converging zone significantly mitigated under-estimation of the observed O3 peak. For example, simulations with adjusted wind fields and adjusted (emissions + wind fields) reduced under-estimation of the peak

  3. Evolution of sputtering target surface composition in reactive high power impulse magnetron sputtering

    Science.gov (United States)

    Kubart, T.; Aijaz, A.

    2017-05-01

    The interaction between pulsed plasmas and surfaces undergoing chemical changes complicates physics of reactive High Power Impulse Magnetron Sputtering (HiPIMS). In this study, we determine the dynamics of formation and removal of a compound on a titanium surface from the evolution of discharge characteristics in an argon atmosphere with nitrogen and oxygen. We show that the time response of a reactive process is dominated by surface processes. The thickness of the compound layer is several nm and its removal by sputtering requires ion fluence in the order of 1016 cm-2, much larger than the ion fluence in a single HiPIMS pulse. Formation of the nitride or oxide layer is significantly slower in HiPIMS than in dc sputtering under identical conditions. Further, we explain very high discharge currents in HiPIMS by the formation of a truly stoichiometric compound during the discharge off-time. The compound has a very high secondary electron emission coefficient and leads to a large increase in the discharge current upon target poisoning.

  4. Effects of surface treating methods of high-strength carbon fibers on interfacial properties of epoxy resin matrix composite

    Science.gov (United States)

    Ma, Quansheng; Gu, Yizhuo; Li, Min; Wang, Shaokai; Zhang, Zuoguang

    2016-08-01

    This paper aims to study the effects of surface treating methods, including electrolysis of anodic oxidation, sizing and heat treatment at 200 °C, on physical and chemical properties of T700 grade high-strength carbon fiber GQ4522. The fiber surface roughness, surface energy and chemical properties were analyzed for different treated carbon fibers, using atom force microscopy, contact angle, Fourier transformed infrared and X-ray photoelectron spectroscopy, respectively. The results show that the adopted surface treating methods significantly affect surface roughness, surface energy and active chemical groups of the studied carbon fibers. Electrolysis and sizing can increase the roughness, surface energy and chemical groups on surface, while heat treatment leads to decreases in surface energy and chemical groups due to chemical reaction of sizing. Then, unidirectional epoxy 5228 matrix composite laminates were prepared using different treated GQ4522 fibers, and interlaminar shear strength and flexural property were measured. It is revealed that the composite using electrolysis and sizing-fiber has the strongest interfacial bonding strength, indicating the important roles of the two treating processes on interfacial adhesion. Moreover, the composite using heat-treating fiber has lower mechanical properties, which is attributed to the decrease of chemical bonding between fiber surface and matrix after high temperature treatment of fiber.

  5. Deuterium trapping and surface modification of polycrystalline tungsten exposed to a high-flux plasma at high fluences

    Science.gov (United States)

    Zibrov, M.; Balden, M.; Morgan, T. W.; Mayer, M.

    2017-04-01

    Deuterium (D) retention and surface modifications of hot-rolled polycrystalline tungsten (W) exposed to a low-energy (~40 eV D‑1), high-flux (2–5  ×  1023 D m‑2 s‑1) D plasma at temperatures of ~380 K and ~1140 K to fluences up to 1.2  ×  1028 D m‑2 have been examined by using nuclear reaction analysis, thermal desorption spectroscopy, and scanning electron microscopy. The samples exposed at ~380 K exhibited various types of surface modifications: dome-shaped blister-like structures, stepped flat-topped protrusions, and various types of nanostructures. It was observed that a large fraction of the surface was covered with blisters and protrusions, but their average size and the number density showed almost no fluence dependence. The D depth distributions and total D inventories also barely changed with increasing fluence at ~380 K. A substantial amount of D was retained in the subsurface region, and thickness correlated with the depth where the cavities of blisters and protrusions were located. It is therefore suggested that defects appearing during creation of blisters and protrusions govern the D trapping in the investigated fluence range. In addition, a large number of small cracks was observed on the exposed surfaces, which can serve as fast D release channels towards the surface, resulting in a reduction of the effective D influx into the W bulk. On the samples exposed at ~1140 K no blisters and protrusions were found. However, wave-like and faceted terrace-like structures were formed instead. The concentrations of trapped D were very low (<10‑5 at. fr.) after the exposure at ~1140 K.

  6. Simple equations guide high-frequency surface-wave investigation techniques

    Science.gov (United States)

    Xia, J.; Xu, Y.; Chen, C.; Kaufmann, R.D.; Luo, Y.

    2006-01-01

    We discuss five useful equations related to high-frequency surface-wave techniques and their implications in practice. These equations are theoretical results from published literature regarding source selection, data-acquisition parameters, resolution of a dispersion curve image in the frequency-velocity domain, and the cut-off frequency of high modes. The first equation suggests Rayleigh waves appear in the shortest offset when a source is located on the ground surface, which supports our observations that surface impact sources are the best source for surface-wave techniques. The second and third equations, based on the layered earth model, reveal a relationship between the optimal nearest offset in Rayleigh-wave data acquisition and seismic setting - the observed maximum and minimum phase velocities, and the maximum wavelength. Comparison among data acquired with different offsets at one test site confirms the better data were acquired with the suggested optimal nearest offset. The fourth equation illustrates that resolution of a dispersion curve image at a given frequency is directly proportional to the product of a length of a geophone array and the frequency. We used real-world data to verify the fourth equation. The last equation shows that the cut-off frequency of high modes of Love waves for a two-layer model is determined by shear-wave velocities and the thickness of the top layer. We applied this equation to Rayleigh waves and multi-layer models with the average velocity and obtained encouraging results. This equation not only endows with a criterion to distinguish high modes from numerical artifacts but also provides a straightforward means to resolve the depth to the half space of a layered earth model. ?? 2005 Elsevier Ltd. All rights reserved.

  7. Forming high efficiency silicon solar cells using density-graded anti-reflection surfaces

    Science.gov (United States)

    Yuan, Hao-Chih; Branz, Howard M.; Page, Matthew R.

    2014-09-09

    A method (50) is provided for processing a graded-density AR silicon surface (14) to provide effective surface passivation. The method (50) includes positioning a substrate or wafer (12) with a silicon surface (14) in a reaction or processing chamber (42). The silicon surface (14) has been processed (52) to be an AR surface with a density gradient or region of black silicon. The method (50) continues with heating (54) the chamber (42) to a high temperature for both doping and surface passivation. The method (50) includes forming (58), with a dopant-containing precursor in contact with the silicon surface (14) of the substrate (12), an emitter junction (16) proximate to the silicon surface (14) by doping the substrate (12). The method (50) further includes, while the chamber is maintained at the high or raised temperature, forming (62) a passivation layer (19) on the graded-density silicon anti-reflection surface (14).

  8. Nanoengineered Surfaces for High Flux Thin Film Evaporation

    Science.gov (United States)

    2013-07-15

    omniphobicity. Nature, 2011. 477(7365): p. 443-447. 50. Anand, S., et al., Enhanced Condensation on Lubricant Impregnated Nanotextured Surfaces. Acs Nano ...time, (c) corresponding droplet volume as a function of time. To explain the observations, we developed a simple quasi-steady 1-D lubrication ...consistent with experimental observations. A typical experimental data and the model prediction are shown in Fig. 11. The simple 1-D lubrication

  9. Electromigration occurrences and its effects on metallic surfaces submitted to high electromagnetic field : A novel approach to breakdown in accelerators

    CERN Document Server

    Antoine, C; Pimpec, F Le

    2011-01-01

    The application of a high electrical field on metallic surfaces leads to the well described phenomena of breakdown. In the classical scenario, explosive electron emission (EEE), breakdown (BD) originates from an emitting site (surface protrusion). The conditioning process consists of "burning" the emitting sites one after another and numerous observations exhibit surfaces covered with molten craters that more or less overlap. When dealing with RF cavities for accelerators, where increasingly fields are now sought, one can legitimately wonder if other physical phenomena should also be taken into account. In particular, we believe that electromigration, especially at surfaces or grain boundaries cannot be neglected anymore at high field (i.e. 50-100 MV/m). Many publications in the domain of liquid metal emission sources show that very stable and strong emission sources, either ions or electrons, build up on metallic surfaces submitted to electrical fields through a mechanism that is slightly different from the ...

  10. Patients with Rheumatoid Arthritis Show Altered Lipoprotein Profiles with Dysfunctional High-Density Lipoproteins that Can Exacerbate Inflammatory and Atherogenic Process.

    Science.gov (United States)

    Kim, Jae-Yong; Lee, Eun-Young; Park, Jin Kyun; Song, Yeong Wook; Kim, Jae-Ryong; Cho, Kyung-Hyun

    2016-01-01

    In order to identify putative biomarkers in lipoprotein, we compared lipid and lipoprotein properties between rheumatoid arthritis (RA) patients and control with similar age. We analyzed four classes of lipoproteins (VLDL, LDL, HDL2, HDL3) from both male (n = 8, 69±4 year-old) and female (n = 25, 53±7 year-old) rheumatoid arthritis (RA) patients as well as controls with similar age (n = 13). Although RA group showed normal levels of total cholesterol (TC), low-density lipoprotein (LDL)-cholesterol, and glucose, however, the RA group showed significantly reduced high-density lipoprotein (HDL)-C level and ratio of HDL-C/TC. The RA group showed significantly elevated levels of blood triglyceride (TG), uric acid, and cholesteryl ester transfer protein (CETP) activity. The RA group also showed elevated levels of advanced glycated end (AGE) products in all lipoproteins and severe aggregation of apoA-I in HDL. As CETP activity and TG contents were 2-fold increased in HDL from RA group, paraoxonase activity was reduced upto 20%. Electron microscopy revealed that RA group showed much less HDL2 particle number than control. LDL from the RA group was severely oxidized and glycated with greater fragmentation of apo-B, especially in female group, it was more atherogenic via phagocytosis. Lipoproteins from the RA patients showed severely altered structure with impaired functionality, which is very similar to that observed in coronary heart patients. These dysfunctional properties in lipoproteins from the RA patients might be associated with high incidence of cardiovascular events in RA patients.

  11. Abnormal high surface heat flow caused by the Emeishan mantle plume

    Science.gov (United States)

    Jiang, Qiang; Qiu, Nansheng; Zhu, Chuanqing

    2016-04-01

    It is commonly believed that increase of heat flow caused by a mantle plume is small and transient. Seafloor heat flow data near the Hawaiian hotspot and the Iceland are comparable to that for oceanic lithosphere elsewhere. Numerical modeling of the thermal effect of the Parana large igneous province shows that the added heat flow at the surface caused by the magmatic underplating is less than 5mW/m2. However, the thermal effect of Emeishan mantle plume (EMP) may cause the surface hear-flow abnormally high. The Middle-Late Emeishan mantle plume is located in the western Yangtze Craton. The Sichuan basin, to the northeast of the EMP, is a superimposed basin composed of Paleozoic marine carbonate rocks and Mesozoic-Cenozoic terrestrial clastic rocks. The vitrinite reflectance (Ro) data as a paleogeothermal indicator records an apparent change of thermal regime of the Sichuan basin. The Ro profiles from boreholes and outcrops which are close to the center of the basalt province exhibit a 'dog-leg' style at the unconformity between the Middle and Upper Permian, and they show significantly higher gradients in the lower subsection (pre-Middle Permian) than the Upper subsection (Upper Permian to Mesozoic). Thermal history inversion based on these Ro data shows that the lower subsection experienced a heat flow peak much higher than that of the upper subsection. The abnormal heat flow in the Sichuan basin is consistent with the EMP in temporal and spatial distribution. The high-temperature magmas from deep mantle brought heat to the base of the lithosphere, and then large amount of heat was conducted upwards, resulting in the abnormal high surface heat flow.

  12. Andreev reflection without Fermi surface alignment in high-T c van der Waals heterostructures

    Science.gov (United States)

    Zareapour, Parisa; Hayat, Alex; Zhao, Shu Yang F.; Kreshchuk, Michael; Xu, Zhijun; Liu, T. S.; Gu, G. D.; Jia, Shuang; Cava, Robert J.; Yang, H.-Y.; Ran, Ying; Burch, Kenneth S.

    2017-04-01

    We address the controversy over the proximity effect between topological materials and high-T c superconductors. Junctions are produced between Bi2Sr2CaCu2O{}8+δ and materials with different Fermi surfaces (Bi2Te3 and graphite). Both cases reveal tunneling spectra that are consistent with Andreev reflection. This is confirmed by a magnetic field that shifts features via the Doppler effect. This is modeled with a single parameter that accounts for tunneling into a screening supercurrent. Thus the tunneling involves Cooper pairs crossing the heterostructure, showing that the Fermi surface mismatch does not hinder the ability to form transparent interfaces, which is accounted for by the extended Brillouin zone and different lattice symmetries.

  13. High surface area graphite as alternative support for proton exchange membrane fuel cell catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Ferreira-Aparicio, P.; Folgado, M.A. [Centro de Investigaciones Energeticas, Medioambientales y Tecnologicas (CIEMAT), Avda. Complutense 22, E-28040 Madrid (Spain); Daza, L. [Centro de Investigaciones Energeticas, Medioambientales y Tecnologicas (CIEMAT), Avda. Complutense 22, E-28040 Madrid (Spain); Instituto de Catalisis y Petroleoquimica (CSIC), C/Marie Curie, 2 Campus de Cantoblanco, E-28049 Madrid (Spain)

    2009-07-01

    The suitability of a high surface area graphite (HSAG) as proton exchange membrane fuel cell (PEMFC) catalyst support has been evaluated and compared with that of the most popular carbon black: the Vulcan XC72. It has been observed that Pt is arranged on the graphite surface resulting in different structures which depend on the catalysts synthesis conditions. The influence that the metal particle size and the metal-support interaction exert on the catalysts degradation rate is analyzed. Temperature programmed oxidation (TPO) under oxygen containing streams has been shown to be a useful method to assess the resistance of PEMFC catalysts to carbon corrosion. The synthesized Pt/HSAG catalysts have been evaluated in single cell tests in the cathode catalytic layer. The obtained results show that HSAG can be a promising alternative to the traditionally used Vulcan XC72 carbon black when suitable catalysts synthesis conditions are used. (author)

  14. Nanoporous gold as a highly active substrate for surface-enhanced Raman scattering spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Kucheyev, S O; Hayes, J R; Biener, J; Hamza, A V

    2006-03-28

    Colloidal solutions of metal nanoparticles are currently among most studied substrates for sensors based on surface-enhanced Raman scattering (SERS). However, such substrates often suffer from not being cost-effective, reusable, or stable. Here, we develop nanoporous Au as a highly active, tunable, a.ordable, stable, bio-compatible, and reusable SERS substrate. Nanoporous Au is prepared by a facile process of free corrosion of AgAu alloys followed by annealing. Results show that nanofoams with average pore sizes of {approx} 250 nm exhibit the largest SERS signal for 632.8 nm excitation. This is attributed to the electromagnetic SERS enhancement mechanism with additional field localization within pores.

  15. High frequency surface acoustic wave resonator-based sensor for particulate matter detection

    OpenAIRE

    Thomas, Sanju; Cole, Marina; Villa-López, Farah Helue; Gardner, J. W.

    2016-01-01

    This paper describes the characterization of high frequency Surface Acoustic Wave Resonator-based (SAWR) sensors, for the detection of micron and sub-micron sized particles. The sensor comprises two 262 MHz ST-cut quartz based Rayleigh wave SAWRs where one is used for particle detection and the other as a reference. Electro-acoustic detection of different sized particles shows a strong relationship between mass sensitivity (Δf/Δm) and particle diameter (Dp). This enables frequency-dependent S...

  16. A surface science compatible epifluorescence microscope for inspection of samples under ultra high vacuum and cryogenic conditions

    Science.gov (United States)

    Marquardt, Christian; Paulheim, Alexander; Rohbohm, Nils; Merkel, Rudolf; Sokolowski, Moritz

    2017-08-01

    We modified an epi-illumination light microscope and mounted it on an ultra high vacuum chamber for investigating samples used in a surface science experiment. For easy access and bake out, all optical components are placed outside the vacuum and the sample is imaged through a glass window. The microscope can be operated in reflection brightfield or epifluorescence mode to image the sample surface or fluorescent dye molecules adsorbed on it. The homemade sample mounting was made compatible for the use under the microscope; sample temperatures as low as 6 K can be achieved. The performance of the microscope is demonstrated on two model samples: Brightfield-images of a well-prepared Ag(100) surface show a macroscopic corrugation of the surface, although low energy electron diffraction data indicate a highly ordered crystalline surface. The surface shows macroscopic protrusions with flat regions, about 20-200 μm in diameter, in between. Fluorescence images of diluted 3,4,9,10-perylene tetracarboxylicacid dianhydride (PTCDA) molecules adsorbed on an ultrathin epitaxial KCl film on the Ag(100) surface show a shading effect at surface protrusions due to an inclined angle of incidence of the PTCDA beam during deposition. For some preparations, the distribution of the fluorescence intensity is inhomogeneous and shows a dense network of bright patches about 5 μm in diameter related to the macroscopic corrugation of the surface. We propose that such a light microscope can aid many surface science experiments, especially those dealing with epitaxial growth or fluorescent materials.

  17. A surface science compatible epifluorescence microscope for inspection of samples under ultra high vacuum and cryogenic conditions.

    Science.gov (United States)

    Marquardt, Christian; Paulheim, Alexander; Rohbohm, Nils; Merkel, Rudolf; Sokolowski, Moritz

    2017-08-01

    We modified an epi-illumination light microscope and mounted it on an ultra high vacuum chamber for investigating samples used in a surface science experiment. For easy access and bake out, all optical components are placed outside the vacuum and the sample is imaged through a glass window. The microscope can be operated in reflection brightfield or epifluorescence mode to image the sample surface or fluorescent dye molecules adsorbed on it. The homemade sample mounting was made compatible for the use under the microscope; sample temperatures as low as 6 K can be achieved. The performance of the microscope is demonstrated on two model samples: Brightfield-images of a well-prepared Ag(100) surface show a macroscopic corrugation of the surface, although low energy electron diffraction data indicate a highly ordered crystalline surface. The surface shows macroscopic protrusions with flat regions, about 20-200 μm in diameter, in between. Fluorescence images of diluted 3,4,9,10-perylene tetracarboxylicacid dianhydride (PTCDA) molecules adsorbed on an ultrathin epitaxial KCl film on the Ag(100) surface show a shading effect at surface protrusions due to an inclined angle of incidence of the PTCDA beam during deposition. For some preparations, the distribution of the fluorescence intensity is inhomogeneous and shows a dense network of bright patches about 5 μm in diameter related to the macroscopic corrugation of the surface. We propose that such a light microscope can aid many surface science experiments, especially those dealing with epitaxial growth or fluorescent materials.

  18. Evaluation of Surface Roughness and Bacterial Adhesion on Tooth Enamel Irradiated With High Intensity Lasers.

    Science.gov (United States)

    Nogueira, Ruchele D; Silva, Camilla B; Lepri, Cesar P; Palma-Dibb, Regina Guenka; Geraldo-Martins, Vinicius R

    2017-01-01

    The aim was to evaluate the surface roughness and bacterial adhesion on enamel irradiated with high intensity lasers, associated or not to a fluoride varnish. Eighty fragments of bovine enamel were equally divided in 8 groups (n=10). Group 1 was not treated and Group 2 received only a 5% fluoride varnish application. The other groups were irradiated with an Er:Cr:YSGG (8.92 J/cm2), an Nd:YAG (84.9 J/cm2) and a diode laser (199.04 J/cm2), associated or not to a 5% fluoride varnish. The surface roughness was measured before and after treatments. Afterward, all samples were incubated in a suspension of S. mutans at 37 °C for 24 h. The colony-forming units (CFU) were counted by a stereoscope and the results were expressed in CFU/mm2. One-way ANOVA and the Tukey´s test compared the roughness data and the Student´s test compared the results obtained in the bacterial adhesion test (a=5%). The results showed that the irradiated samples without varnish presented the same roughness and the same bacterial adhesion that the non-irradiated samples. However, samples irradiated in the presence of fluoride varnish showed higher surface roughness and higher bacterial adhesion than the non-irradiated samples and those irradiated without varnish. Presence of pigments in the varnish increased the lasers' action on the enamel surface, which produced ablation in this hard tissue and significantly increased its surface roughness. For this reason, the enamel's susceptibility to bacterial adhesion was higher when the irradiation of the samples was made in presence of fluoride varnish.

  19. Aerodynamic roughness of glacial ice surfaces derived from high-resolution topographic data

    Science.gov (United States)

    Smith, Mark W.; Quincey, Duncan J.; Dixon, Timothy; Bingham, Robert G.; Carrivick, Jonathan L.; Irvine-Fynn, Tristram D. L.; Rippin, David M.

    2016-04-01

    This paper presents new methods of estimating the aerodynamic roughness (z0) of glacier ice directly from three-dimensional point clouds and digital elevation models (DEMs), examines temporal variability of z0, and presents the first fully distributed map of z0 estimates across the ablation zone of an Arctic glacier. The aerodynamic roughness of glacier ice surfaces is an important component of energy balance models and meltwater runoff estimates through its influence on turbulent fluxes of latent and sensible heat. In a warming climate these fluxes are predicted to become more significant in contributing to overall melt volumes. Ice z0 is commonly estimated from measurements of ice surface microtopography, typically from topographic profiles taken perpendicular to the prevailing wind direction. Recent advances in surveying permit rapid acquisition of high-resolution topographic data allowing revision of assumptions underlying conventional z0 measurement. Using Structure from Motion (SfM) photogrammetry with Multi-View Stereo (MVS) to survey ice surfaces with millimeter-scale accuracy, z0 variation over 3 orders of magnitude was observed. Different surface types demonstrated different temporal trajectories in z0 through 3 days of intense melt. A glacier-scale 2 m resolution DEM was obtained through terrestrial laser scanning (TLS), and subgrid roughness was significantly related to plot-scale z0. Thus, we show for the first time that glacier-scale TLS or SfM-MVS surveys can characterize z0 variability over a glacier surface potentially leading to distributed representations of z0 in surface energy balance models.

  20. Mineral Surface after Reaction with Aqueous Solution at High Temperatures and Pressures

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    This work presents new experimental results on surface chemistry of reacting minerals and interface kinetics between mineral and aqueous solutions. These experiments were carried out using a flow reactor (packed bed reactor) of an open system as well as a continuous stirred tank reactor, CSTR. The authors measured reaction rates of such minerals as zeolite, albite and carbonate (rhodochrosite, dolomite) in various solutions, and tested corresponding mineral surface by using SEM, XPS, SIMS, etc. This paper mainly presents the experimental results of zeolite dissolution in water and in low pH solutions at room temperature, and dolomite dissolution at elevated temperatures. The results show that the release rates of Si, Al and Na of zeolite are different in most cases. The incongruent dissolution of zeolite is related to surface chemical modifications. The Na, Al and Si release rates for dissolution of albite and zeolite in water and various solutions were measured as a function of temperature, flow velocity, pH and solution composition in the reaction system. In most cases, dissolutions of both albite and zeolite are incongruent. Dissolution of dolomite is also incongruent in most cases and varied with T, pH, and nature of aqueous solutions. For dolomite dissolution, the release rates of Mg are less than those of Ca at high temperatures as T increases from 25 to 300° C. SIMS study indicates that the contents of Al, Na and Si in the leached layer of zeolite or albite surface, change with the distance from the surface, exhibiting a non-linear behaviour within a thickness range of 1000%. The distributions of Ca, Mg, Mn, H and Cl in the leached surface layer of carbonate have a non-linear behaviour too.

  1. High-fluence hyperthermal ion irradiation of gallium nitride surfaces at elevated temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Finzel, A.; Gerlach, J.W., E-mail: juergen.gerlach@iom-leipzig.de; Lorbeer, J.; Frost, F.; Rauschenbach, B.

    2014-10-30

    Highlights: • Irradiation of gallium nitride films with hyperthermal nitrogen ions. • Surface roughening at elevated sample temperatures was observed. • No thermal decomposition of gallium nitride films during irradiation. • Asymmetric surface diffusion processes cause local roughening. - Abstract: Wurtzitic GaN films deposited on 6H-SiC(0001) substrates by ion-beam assisted molecular-beam epitaxy were irradiated with hyperthermal nitrogen ions with different fluences at different substrate temperatures. In situ observations with reflection high energy electron diffraction showed that during the irradiation process the surface structure of the GaN films changed from two dimensional to three dimensional at elevated temperatures, but not at room temperature. Atomic force microscopy revealed an enhancement of nanometric holes and canyons upon the ion irradiation at higher temperatures. The roughness of the irradiated and heated GaN films was clearly increased by the ion irradiation in accordance with x-ray reflectivity measurements. A sole thermal decomposition of the films at the chosen temperatures could be excluded. The results are discussed taking into account temperature dependent sputtering and surface uphill adatom diffusion as a function of temperature.

  2. High-conductivity silicon based spectrally selective plasmonic surfaces for sensing in the infrared region

    Science.gov (United States)

    Gorgulu, K.; Gok, A.; Yilmaz, M.; Topalli, K.; Okyay, A. K.

    2017-02-01

    Plasmonic perfect absorbers have found a wide range of applications in imaging, sensing, and light harvesting and emitting devices. Traditionally, metals are used to implement plasmonic structures. For sensing applications, it is desirable to integrate nanophotonic active surfaces with biasing and amplification circuitry to achieve monolithic low cost solutions. Commonly used plasmonic metals such as Au and Ag are not compatible with standard silicon complementary metal-oxide-semiconductor (CMOS) technology. Here we demonstrate plasmonic perfect absorbers based on high conductivity silicon. Standard optical lithography and reactive ion etching techniques were used for the patterning of the samples. We present computational and experimental results of surface plasmon resonances excited on a silicon surface at normal and oblique incidences. We experimentally demonstrate our absorbers as ultra-low cost, CMOS-compatible and efficient refractive index sensing surfaces. The experimental results reveal that the structure exhibits a sensitivity of around 11 000 nm/RIU and a figure of merit of up to 2.5. We also show that the sensing performance of the structure can be improved by increasing doping density.

  3. Biocompatible gold nanorods: one-step surface functionalization, highly colloidal stability, and low cytotoxicity.

    Science.gov (United States)

    Liu, Kang; Zheng, Yuanhui; Lu, Xun; Thai, Thibaut; Lee, Nanju Alice; Bach, Udo; Gooding, J Justin

    2015-05-05

    The conjugation of gold nanorods (AuNRs) with polyethylene glycol (PEG) is one of the most effective ways to reduce their cytotoxicity arising from the cetyltrimethylammonium bromide (CTAB) and silver ions used in their synthesis. However, typical PEGylation occurs only at the tips of the AuNRs, producing partially modified AuNRs. To address this issue, we have developed a novel, facile, one-step surface functionalization method that involves the use of Tween 20 to stabilize AuNRs, bis(p-sulfonatophenyl)phenylphosphine (BSPP) to activate the AuNR surface for the subsequent PEGylation, and NaCl to etch silver from the AuNRs. This method allows for the complete removal of the surface-bound CTAB and the most active surface silver from the AuNRs. The produced AuNRs showed far lower toxicity than other methods to PEGylate AuNRs, with no apparent toxicity when their concentration is lower than 5 μg/mL. Even at a high concentration of 80 μg/mL, their cell viability is still four times higher than that of the tip-modified AuNRs.

  4. Engineering of poly(ethylene glycol chain-tethered surfaces to obtain high-performance bionanoparticles

    Directory of Open Access Journals (Sweden)

    Yukio Nagasaki

    2010-01-01

    Full Text Available A poly(ethylene glycol-b-poly[2-(N,N-dimethylaminoethyl methacrylate] block copolymer possessing a reactive acetal group at the end of the poly(ethylene glycol (PEG chain, that is, acetal-PEG-b-PAMA, was synthesized by a proprietary polymerization technique. Gold nanoparticles (GNPs were prepared using the thus-synthesized acetal-PEG-b-PAMA block copolymer. The PEG-b-PAMA not only acted as a reducing agent of aurate ions but also attached to the nanoparticle surface. The GNPs obtained had controlled sizes and narrow size distributions. They also showed high dispersion stability owing to the presence of PEG tethering chains on the surface. The same strategy should also be applicable to the fabrication of semiconductor quantum dots and inorganic porous nanoparticles. The preparation of nanoparticles in situ, i.e. in the presence of acetal-PEG-b-PAMA, gave the most densely packed polymer layer on the nanoparticle surface; this was not observed when coating preformed nanoparticles. PEG/polyamine block copolymer was more functional on the metal surface than PEG/polyamine graft copolymer, as confirmed by angle-dependent x-ray photoelectron spectroscopy. We successfully solubilized the C60 fullerene into aqueous media using acetal-PEG-b-PAMA. A C60/acetal-PEG-b-PAMA complex with a size below 5 nm was obtained by dialysis. The preparation and characterization of these materials are described in this review.

  5. Extraction of bulk generation lifetime and surface generation velocity in high-resistivity silicon by means of gated diodes

    CERN Document Server

    Verzellesi, G; Bosisio, L; Dalla Betta, Gian Franco; Pignatel, Giogrio Umberto

    2002-01-01

    We show that the accuracy of the gated diode method for measuring bulk generation lifetime and surface generation velocity in high resistivity silicon depends critically on the gate length of the test device, as a result of nonidealities affecting the gated diode operation. Minimization of the surface generation velocity measurement error requires the gate length to be suitably decreased, while long gate length structures are needed for accurate bulk generation lifetime extraction.

  6. Resistive Memory for Harsh Electronics: Immunity to Surface Effect and High Corrosion Resistance via Surface Modification

    Science.gov (United States)

    Huang, Teng-Han; Yang, Po-Kang; Lien, Der-Hsien; Kang, Chen-Fang; Tsai, Meng-Lin; Chueh, Yu-Lun; He-Hau, Jr.

    2014-03-01

    The tolerance/resistance of the electronic devices to extremely harsh environments is of supreme interest. Surface effects and chemical corrosion adversely affect stability and operation uniformity of metal oxide resistive memories. To achieve the surrounding-independent behavior, the surface modification is introduced into the ZnO memristors via incorporating fluorine to replace the oxygen sites. F-Zn bonds is formed to prevent oxygen chemisorption and ZnO dissolution upon corrosive atmospheric exposure, which effectively improves switching characteristics against harmful surroundings. In addition, the fluorine doping stabilizes the cycling endurance and narrows the distribution of switching parameters. The outcomes provide valuable insights for future nonvolatile memory developments in harsh electronics.

  7. Influence of statistical surface models on dynamic scattering of high-frequency signals from the ocean surface (A)

    DEFF Research Database (Denmark)

    Bjerrum-Niese, Christian; Jensen, Leif Bjørnø

    1994-01-01

    Temporal variations of scattering of high-frequency, monochromatic signals from the ocean surface has been studied numerically. In the high-frequency domain the dynamic scattering can be modeled by a coherence function of the scattered pressure field, which is based on the Kirchhoff integral...... for the Pierson–Moskowitz spectrum (for a fully developed sea) with computations for the JONSWAP spectrum (for fetch-limited seas). The following results, among other issues, have been obtained: As the fetch decreases, the surface waves become shorter, leading to increasing frequency shifting of the scattered...... signal. [Work sponsored by the Danish Technical Research Council and the EU/MAST programme.]...

  8. Facile and scalable preparation of highly wear-resistance superhydrophobic surface on wood substrates using silica nanoparticles modified by VTES

    Energy Technology Data Exchange (ETDEWEB)

    Jia, Shanshan; Liu, Ming [College of Materials Science and Engineering, Central South University of Forestry and Technology, Changsha 410004 (China); Wu, Yiqiang, E-mail: wuyq0506@126.com [College of Materials Science and Engineering, Central South University of Forestry and Technology, Changsha 410004 (China); Hunan Provincial Collaborative Innovation Center for High-efficiency Utilization of Wood and Bamboo Resources, Central South University of Forestry and Technology, Changsha 410004 (China); Luo, Sha [College of Materials Science and Engineering, Central South University of Forestry and Technology, Changsha 410004 (China); Qing, Yan, E-mail: qingyan0429@163.com [College of Materials Science and Engineering, Central South University of Forestry and Technology, Changsha 410004 (China); Hunan Provincial Collaborative Innovation Center for High-efficiency Utilization of Wood and Bamboo Resources, Central South University of Forestry and Technology, Changsha 410004 (China); Chen, Haibo [College of Materials Science and Engineering, Central South University of Forestry and Technology, Changsha 410004 (China)

    2016-11-15

    Graphical abstract: Highly wear-resistance superhydrophobic surface on wood substrates was fabricated using silica nanoparticles modified by VTES. Display Omitted - Highlights: • Superhydrophobic surface on wood substrates was efficiently fabricated using nanoparticles modified by VTES. • The superhydrophobic surface exhibited a CA of 154° and a SAclose to 0°. • The superhydrophobic surface showed a durable and robust wear-resistance performance. - Abstract: In this study, an efficient, facile method has been developed for fabricating superhydrophobic surfaces on wood substrates using silica nanoparticles modified by VTES. The as-prepared superhydrophobic wood surface had a water contact angle of 154° and water slide angle close to 0°. Simultaneously, this superhydrophobic wood showed highly durable and robust wear resistance when having undergone a long period of sandpaper abrasion or being scratched by a knife. Even under extreme conditions of boiling water, the superhydrophobicity of the as-prepared wood composite was preserved. Characterizations by scanning electron microscopy, energy-dispersive X-ray spectroscopy, and Fourier transform infrared spectroscopy showed that a typical and tough hierarchical micro/nanostructure was created on the wood substrate and vinyltriethoxysilane contributed to preventing the agglomeration of silica nanoparticles and serving as low-surface-free-energy substances. This superhydrophobic wood was easy to fabricate, mechanically resistant and exhibited long-term stability. Therefore, it is considered to be of significant importance in the industrial production of functional wood, especially for outdoor applications.

  9. Modification of highly oriented pyrolytic graphite (HOPG) surfaces with highly charged ion (HCI) irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Koguchi, Y. E-mail: ykoguchi@postman.riken.go.jp; Meguro, T.; Hida, A.; Takai, H.; Maeda, K.; Yamamoto, Y.; Aoyagi, Y

    2003-05-01

    Slow Ar{sup 8+} irradiation and the following electron injection creates a non-conductive area to a depth of a few nanometers on a highly oriented pyrolytic graphite surface (HOPG). The annealing of the sample in a hydrogen atmosphere stabilizes the Ar{sup 8+} impact area, which results in the field emission from the impact region. The property of the field emission is similar to that of diamond-like carbon (DLC), suggesting the possibility that sp{sup 3} hybridization occurs at the Ar{sup 8+} impact region. The work function estimated from the Fowler-Nordheim plot is much lower than non-treated HOPG and similar to a hydrogen-terminated DLC film.

  10. Low energy high current pulsed electron beam treatment for improving surface microstructure and properties

    Energy Technology Data Exchange (ETDEWEB)

    Wu, J; Allain-Bonasso, N; Zhang, X D; Hao, S Z; Grosdider, T; Dong, C [Laboratoire d' Etude des Textures et Applications aux Materiaux (LETAM, UMR-CNRS 3143), Universite Paul Verlaine-Metz, Ile du Saulcy, 57045 Metz (France); Zou, J X, E-mail: jiang.wu@univ-metz.fr, E-mail: thierry.grosdidier@univ-metz.fr [National Engineering Research Center of Light Alloy Net Forming, Shanghai Jiao Tong University, Shanghai 200240 (China)

    2010-06-15

    Low energy high current pulsed electron beam (LEHCPEB) is a fairly new technique for surface modifications authorizing improvement in wear and corrosion properties as well as texture changes and hardening. This contribution highlights some microstructure modifications encountered at the surface of HCPEB treated steels and bulk metallic glasses taking into account the effects of surface melting and the effects of the induced stress.

  11. Microstructural and hardness gradients in Cu processed by high pressure surface rolling

    DEFF Research Database (Denmark)

    He, Q. Y.; Zhu, X.-M.; Mei, Q. S.

    2017-01-01

    in the topmost surface to the microscale in the bulk. The hardness varies from 1.37 GPa at the topmost surface to about 0.6 GPa in the coarse-grained matrix. The results of the investigation demonstrate that the HPSR process shows good potential for the generation of thick gradient microstructures on the surface...

  12. Two dimensional simulation of high power laser-surface interaction

    Energy Technology Data Exchange (ETDEWEB)

    Goldman, S.R.; Wilke, M.D.; Green, R.E.L.; Johnson, R.P. [Los Alamos National Lab., NM (United States); Busch, G.E. [KMS Fusion, Inc., Ann Arbor, MI (United States)

    1998-08-01

    For laser intensities in the range of 10{sup 8}--10{sup 9} W/cm{sup 2}, and pulse lengths of order 10 {micro}sec or longer, the authors have modified the inertial confinement fusion code Lasnex to simulate gaseous and some dense material aspects of the laser-matter interaction. The unique aspect of their treatment consists of an ablation model which defines a dense material-vapor interface and then calculates the mass flow across this interface. The model treats the dense material as a rigid two-dimensional mass and heat reservoir suppressing all hydrodynamic motion in the dense material. The computer simulations and additional post-processors provide predictions for measurements including impulse given to the target, pressures at the target interface, electron temperatures and densities in the vapor-plasma plume region, and emission of radiation from the target. The authors will present an analysis of some relatively well diagnosed experiments which have been useful in developing their modeling. The simulations match experimentally obtained target impulses, pressures at the target surface inside the laser spot, and radiation emission from the target to within about 20%. Hence their simulational technique appears to form a useful basis for further investigation of laser-surface interaction in this intensity, pulse-width range. This work is useful in many technical areas such as materials processing.

  13. High Resolution Digital Surface Model For Production Of Airport Obstruction Charts Using Spaceborne SAR Sensors

    Science.gov (United States)

    Oliveira, Henrique; Rodrigues, Marco; Radius, Andrea

    2012-01-01

    Airport Obstruction Charts (AOCs) are graphical representations of natural or man-made obstructions (its locations and heights) around airfields, according to International Civil Aviation Organization (ICAO) Annexes 4, 14 and 15. One of the most important types of data used in AOCs production/update tasks is a Digital Surface Model (first reflective surface) of the surveyed area. The development of advanced remote sensing technologies provide the available tools for obstruction data acquisition, while Geographic Information Systems (GIS) present the perfect platform for storing and analyzing this type of data, enabling the production of digital ACOs, greatly contributing to the increase of the situational awareness of pilots and enhancing the air navigation safety level [1]. Data acquisition corresponding to the first reflective surface can be obtained through the use of Airborne Laser-Scanning and Light Detection and Ranging (ALS/LIDAR) or Spaceborne SAR Systems. The need of surveying broad areas, like the entire territory of a state, shows that Spaceborne SAR systems are the most adequate in economic and feasibility terms of the process, to perform the monitoring and producing a high resolution Digital Surface Model (DSM). The high resolution DSM generation depends on many factors: the available data set, the used technique and the setting parameters. To increase the precision and obtain high resolution products, two techniques are available using a stack of data: the PS (Permanent Scatterers) technique [2], that uses large stack of data to identify many stable and coherent targets through multi- temporal analysis, removing the atmospheric contribution and to minimize the estimation errors, and the Small Baseline Subset (SBAS) technique ([3],[4]), that relies on the use of small baseline SAR interferograms and on the application of the so called singular value decomposition (SVD) method, in order to link independent SAR acquisition data sets, separated by large

  14. Direct Observation of the Outermost Surfaces of Mesoporous Silica Thin Films by High Resolution Ultralow Voltage Scanning Electron Microscopy.

    Science.gov (United States)

    Kobayashi, Maho; Susuki, Kyoka; Otsuji, Haruo; Sakuda, Yusuke; Asahina, Shunsuke; Kikuchi, Naoki; Kanazawa, Toshiyuki; Kuroda, Yoshiyuki; Wada, Hiroaki; Shimojima, Atsushi; Kuroda, Kazuyuki

    2017-02-20

    The properties of the outermost surfaces of mesoporous silica thin films are critical in determining their functions. Obtaining information on the presence or absence of silica layers on the film surfaces and on the degree of mesopore opening is essential for applications of surface mesopores. In this study, the outermost surfaces of mesoporous silica thin films with 3-dimensional orthorhombic and 2-dimensional hexagonal structures were observed using ultralow voltage high resolution scanning electron microscopy (HR-SEM) with decelerating optics. SEM images of the surfaces before and after etching with NH4F were taken at various landing voltages. Comparing the images taken under different conditions indicated that the outermost surfaces of the nonetched mesoporous silica thin films are coated with a thin layer of silica. The images taken at an ultralow landing voltage (i.e., 80 V) showed that the presence or absence of surface silica layers depends on whether the film was etched with an aqueous solution of NH4F. The mesostructures of both the etched and nonetched films were visible in images taken at a conventional landing voltage (2 kV); hence, the ultralow landing voltage was more suitable for analyzing the outermost surfaces. The SEM observations provided detailed information about the surfaces of mesoporous silica thin films, such as the degree of pore opening and their homogeneities. AFM images of nonetched 2-dimensional hexagonal mesoporous silica thin films show that the shape of the silica layer on the surface of the films reflects the curvature of the top surface of the cylindrical mesochannels. SEM images taken at various landing voltages are discussed, with respect to the electron penetration range at each voltage. This study increases our understanding of the surfaces of mesoporous silica thin films, which may lead to potential applications utilizing the periodically arranged mesopores on these surfaces.

  15. Super-aperture metrology: overcoming a fundamental limit in imaging smooth highly curved surfaces.

    Science.gov (United States)

    Liu, J; Liu, C; Tan, J; Yang, B; Wilson, T

    2016-03-01

    The imaging of smooth, highly curved or tilted surfaces is widely recognized as one of the most challenging and unsolved problems in optical imaging and metrology today. The reason is that even when such surfaces are imaged using high aperture microscope objectives the steepness of the features causes the light to be reflected in such a way that it is not captured by the lens. This is true even in the limiting case of unity numerical aperture since the illuminating light may also be reflected in the forward direction. In order to overcome this fundamental problem we have developed a method whereby such specimens are covered with a readily removable organic fluorescent film thereby creating an isotropic scattering surface. We show that we are readily able to detect slopes with angles close 90° using a 0.75 NA objective--an 82% improvement over the theoretical aperture limit. Issues of variation in film thickness deposition are shown to be readily accommodated. This approach may be used with other fluorophore materials, organic or inorganic, since there is no need for biocompatibility in this application.

  16. Surface Sampling Collection and Culture Methods for Escherichia coli in Household Environments with High Fecal Contamination.

    Science.gov (United States)

    Exum, Natalie G; Kosek, Margaret N; Davis, Meghan F; Schwab, Kellogg J

    2017-08-22

    Empiric quantification of environmental fecal contamination is an important step toward understanding the impact that water, sanitation, and hygiene interventions have on reducing enteric infections. There is a need to standardize the methods used for surface sampling in field studies that examine fecal contamination in low-income settings. The dry cloth method presented in this manuscript improves upon the more commonly used swabbing technique that has been shown in the literature to have a low sampling efficiency. The recovery efficiency of a dry electrostatic cloth sampling method was evaluated using Escherichia coli and then applied to household surfaces in Iquitos, Peru, where there is high fecal contamination and enteric infection. Side-by-side measurements were taken from various floor locations within a household at the same time over a three-month period to compare for consistency of quantification of E. coli bacteria. The dry cloth sampling method in the laboratory setting showed 105% (95% Confidence Interval: 98%, 113%) E. coli recovery efficiency off of the cloths. The field application demonstrated strong agreement of side-by-side results (Pearson correlation coefficient for dirt surfaces was 0.83 (p samples (Pearson (0.53, p method can be utilized in households with high bacterial loads using either continuous (quantitative) or categorical (semi-quantitative) data. The standardization of this low-cost, dry electrostatic cloth sampling method can be used to measure differences between households in intervention and non-intervention arms of randomized trials.

  17. Preparation and Characterization of High Surface Area Activated Carbon Fibers from Lignin

    Directory of Open Access Journals (Sweden)

    Jian Lin

    2016-10-01

    Full Text Available Activated carbon fibers (ACFs were successfully prepared from softwood lignin, which was isolated with polyethylene glycol 400 (PEG-400 as a solvolysis reagent, by water steam activation. The pore characterization and adsorption property of ACFs were investigated. The results showed that all the ACFs with more micropores exhibited high specific surface area and total pore volume which increased with the activation time prolonging; the highest ones were around 3100 m2/g and 1.5 mL/g, respectively. The specific surface area and total pore volume were much larger than those of other types of lignin-based ACFs and activated charcoal. Besides, with increasing activation time, the amount of graphitic carbon, which was the main compound on the surface of ACFs, decreased, while the amount of functional groups containing C–O slightly increased. In addition, the adsorption capacity of ACFs for methylene blue was highly increased as the activation time increased. Accordingly, lignin isolated with PEG is a promising precursor for ACF production.

  18. Beam reconfigurable antenna for the THz band based on a graphene high impedance surface

    Science.gov (United States)

    Radwan, Ahmed; Verri, Valentina; D'Amico, Michele; Gentili, G. Guido

    2017-01-01

    In this paper a reconfigurable beam antenna is proposed for THz applications, based on a switchable Graphene High Impedance Surface (G-HIS) that acts as a reflector for a primary radiator. The Graphene-HIS structure composed of two layers of graphene cells arranged in a 5×5 array, the two planes of the array are separated by a thin silicon oxide layer; patches in the same row are connected together, to be biased by a common DC voltage to the entire row; this gives the ability to control the graphene conductivity σ. The results show that the shape of the radiation pattern can be changed by changing the voltage applied to each row of G-HIS array. The antenna was fabricated and characterized using a THz-TDS laser system. Measurements are in good agreement with simulations as far as the graphene surface impedance and the resonance frequency are concerned. The scanning reflection on the antenna surface due to the change on the applied voltage is presented to show the effect of biased graphene layer on the dipole properties.

  19. High-Surface-Area Nitrogen-Doped Reduced Graphene Oxide for Electric Double-Layer Capacitors.

    Science.gov (United States)

    Youn, Hee-Chang; Bak, Seong-Min; Kim, Myeong-Seong; Jaye, Cherno; Fischer, Daniel A; Lee, Chang-Wook; Yang, Xiao-Qing; Roh, Kwang Chul; Kim, Kwang-Bum

    2015-06-08

    A two-step method consisting of solid-state microwave irradiation and heat treatment under NH3 gas was used to prepare nitrogen-doped reduced graphene oxide (N-RGO) with a high specific surface area (1007 m(2)  g(-1) ), high electrical conductivity (1532 S m(-1) ), and low oxygen content (1.5 wt %) for electrical double-layer capacitor applications. The specific capacitance of N-RGO was 291 F g(-1) at a current density of 1 A g(-1) , and a capacitance of 261 F g(-1) was retained at 50 A g(-1) , which indicated a very good rate capability. N-RGO also showed excellent cycling stability and preserved 96 % of the initial specific capacitance after 100 000 cycles. Near-edge X-ray absorption fine-structure spectroscopy results provided evidenced for the recovery of π conjugation in the carbon networks with the removal of oxygenated groups and revealed chemical bonding of the nitrogen atoms in N-RGO. The good electrochemical performance of N-RGO is attributed to its high surface area, high electrical conductivity, and low oxygen content.

  20. Inundation Mapping Tidal Surface - Mean Higher High Water

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — These data are a derived product of the NOAA VDatum tool and they extend the tool's Mean Higher High Water (MHHW) tidal datum conversion inland beyond its original...

  1. Human papillomavirus viral load in predicting high-grade CIN in women with cervical smears showing only atypical squamous cells or low-grade squamous intraepithelial lesion

    Directory of Open Access Journals (Sweden)

    André Luis Ferreira Santos

    Full Text Available CONTEXT: Human papillomavirus (HPV viral load may have an important role in predicting high-grade cervical intraepithelial neoplasia (CIN in women with cervical smears showing atypical squamous cells or LSIL. OBJECTIVE: To determine whether the assessment of the viral load of high-risk HPV DNA is useful in predicting the detection of high-grade cervical intraepithelial neoplasia (CIN2 and 3 in women referred because of cervical smears showing only atypical squamous cells or LSIL. TYPE OF STUDY: Cross-sectional SETTING: Colposcopy Clinic in a University hospital. METHODS: A series of 119 women referred because of atypical squamous cells or LSIL between August 2000 and April 2001 were included. All women were subjected to a new cervical smear, HPV testing for the high-risk types using hybrid capture II (HCII, viral load measurement in relative light units (RLU and colposcopy, with cervical biopsies (n = 97. Cervical lesions were graded using the CIN classification. RESULTS: Cervical biopsies revealed CIN2 or CIN3 in 11% of the cases, equally among women referred because of atypical squamous cells or LSIL. The HCII test was positive in 16% of women with atypical squamous cells and 52% of those with LSIL (OR = 5.8; 95% CI 1.4 to 26.7. There was strong correlation between CIN2 or CIN3 and positivity for HPV DNA when this group was compared with women with only CIN1 or normal cervix (OR = 7.8; 95% CI 1.5 to 53.4. In ROC analysis for HCII in diagnosing CIN2 and CIN3, the area under the ROC curve was 0.784, and the viral load cutoff point of 10.0 RLU/cutoff presented 77% sensitivity and 73% specificity. Second cytology showing at least atypical squamous cells did not accurately detect CIN2 or CIN3 (OR = 6.4; 95% CI 1.0 to 50.9. The sensitivities of the second cervical smear and HCII were similar, although the specificity of HCII was significantly higher than the second cervical smear. CONCLUSIONS: The viral load of high-risk HPV types was significantly

  2. Method for producing high surface area chromia materials for catalysis

    Science.gov (United States)

    Gash, Alexander E.; Satcher, Joe; Tillotson, Thomas; Hrubesh, Lawrence; Simpson, Randall

    2007-05-01

    Nanostructured chromium(III)-oxide-based materials using sol-gel processing and a synthetic route for producing such materials are disclosed herein. Monolithic aerogels and xerogels having surface areas between 150 m.sup.2/g and 520 m.sup.2/g have been produced. The synthetic method employs the use of stable and inexpensive hydrated-chromium(III) inorganic salts and common solvents such as water, ethanol, methanol, 1-propanol, t-butanol, 2-ethoxy ethanol, and ethylene glycol, DMSO, and dimethyl formamide. The synthesis involves the dissolution of the metal salt in a solvent followed by an addition of a proton scavenger, such as an epoxide, which induces gel formation in a timely manner. Both critical point (supercritical extraction) and atmospheric (low temperature evaporation) drying may be employed to produce monolithic aerogels and xerogels, respectively.

  3. Highly sensitive BTX detection using surface functionalized QCM sensor

    Energy Technology Data Exchange (ETDEWEB)

    Bozkurt, Asuman Aşıkoğlu; Özdemir, Okan; Altındal, Ahmet, E-mail: altindal@yildiz.edu.tr [Department of Physics, Yildiz Technical University, Davutpasa, 34210 Istanbul (Turkey)

    2016-03-25

    A novel organic compound was designed and successfully synthesized for the fabrication of QCM based sensors to detect the low concentrations of BTX gases in indoor air. The effect of the long-range electron orbital delocalization on the BTX vapour sensing properties of azo-bridged Pcs based chemiresistor-type sensors have also been investigated in this work. The sensing behaviour of the film for the online detection of volatile organic solvent vapors was investigated by utilizing an AT-cut quartz crystal resonator. It was observed that the adsorption of the target molecules on the coating surface cause a reversible negative frequency shift of the resonator. Thus, a variety of solvent vapors can be detected by using the phthalocyanine film as sensitive coating, with sensitivity in the ppm range and response times in the order of several seconds depending on the molecular structure of the organic solvent.

  4. Surface-Decorated Silicon Nanowires: A Route to High-ZT Thermoelectrics

    DEFF Research Database (Denmark)

    Markussen, Troels; Jauho, Antti-Pekka; Brandbyge, Mads

    2009-01-01

    Based on atomistic calculations of electron and phonon transport, we propose to use surface-decorated silicon nanowires for thermoelectric applications. Two examples of surface decorations are studied to illustrate the underlying ideas: nanotrees and alkyl functionalized silicon nanowires. For both...... systems we find (i) that the phonon conductance is significantly reduced compared to the electronic conductance leading to high thermoelectric figure of merit ZT, and (ii) for ultrathin wires, surface decoration leads to significantly better performance than surface disorder....

  5. Early auditory processing evoked potentials (N100) show a continuum of blunting from clinical high risk to psychosis in a pediatric sample

    Science.gov (United States)

    Gonzalez-Heydrich, Joseph; Enlow, Michelle Bosquet; D’Angelo, Eugene; Seidman B, Larry J.; Gumlak, Sarah; Kim, April; Woodberry, Kristen A.; Rober, Ashley; Tembulkar, Sahil; Graber, Kelsey; O’Donnell, Kyle; Hamoda, Hesham M.; Kimball, Kara; Rotenberg, Alexander; Oberman, Lindsay M.; Pascual-Leone, Alvaro; Keshavan, Matcheri S.; Duffy, Frank H.

    2016-01-01

    Background The N100 is a negative deflection in the surface EEG approximately 100ms after an auditory signal. It has been shown to be reduced in individuals with schizophrenia and those at clinical high risk (CHR). N100 blunting may index neural network dysfunction underlying psychotic symptoms. This phenomenon has received little attention in pediatric populations. Method This cross-sectional study compared the N100 response measured via the average EEG response at the left medial frontal position FC1 to 150 sinusoidal tones in participants ages 5 to 17 years with a CHR syndrome (n = 29), a psychotic disorder (n = 22), or healthy controls (n=17). Results Linear regression analyses that considered potential covariates (age, gender, handedness, family mental health history, medication usage) revealed decreasing N100 amplitude with increasing severity of psychotic symptomatology from healthy to CHR to psychotic level. Conclusions Longitudinal assessment of the N100 in CHR children who do and do not develop psychosis will inform whether it predicts transition to psychosis and if its response to treatment predicts symptom change. PMID:26549629

  6. Characterization of the surface charge distribution on kaolinite particles using high resolution atomic force microscopy

    Science.gov (United States)

    Kumar, Naveen; Zhao, Cunlu; Klaassen, Aram; van den Ende, Dirk; Mugele, Frieder; Siretanu, Igor

    2016-02-01

    Most solid surfaces, in particular clay minerals and rock surfaces, acquire a surface charge upon exposure to an aqueous environment due to adsorption and/or desorption of ionic species. Macroscopic techniques such as titration and electrokinetic measurements are commonly used to determine the surface charge and ζ -potential of these surfaces. However, because of the macroscopic averaging character these techniques cannot do justice to the role of local heterogeneities on the surfaces. In this work, we use dynamic atomic force microscopy (AFM) to determine the distribution of surface charge on the two (gibbsite-like and silica-like) basal planes of kaolinite nanoparticles immersed in aqueous electrolyte with a lateral resolution of approximately 30 nm. The surface charge density is extracted from force-distance curves using DLVO theory in combination with surface complexation modeling. While the gibbsite-like and the silica-like facet display on average positive and negative surface charge values as expected, our measurements reveal lateral variations of more than a factor of two on seemingly atomically smooth terraces, even if high resolution AFM images clearly reveal the atomic lattice on the surface. These results suggest that simple surface complexation models of clays that attribute a unique surface chemistry and hence homogeneous surface charge densities to basal planes may miss important aspects of real clay surfaces.

  7. Super-surface selective nanomembranes providing simultaneous high permeation flux and high selectivity

    Energy Technology Data Exchange (ETDEWEB)

    Hu, Michael Z.; Simpson, John T.; Aytug, Tolga; Paranthaman, Mariappan Parans; Sturgeon, Matthew R.

    2016-04-12

    Superhydrophobic membrane structures having a beneficial combination of throughput and a selectivity. The membrane structure can include a porous support substrate; and a membrane layer adherently disposed on and in contact with the porous support substrate. The membrane layer can include a nanoporous material having a superhydrophobic surface. The superhydrophobic surface can include a textured surface, and a modifying material disposed on the textured surface. Methods of making and using the membrane structures.

  8. Analysis Code for High Gradient Dielectric Insulator Surface Breakdown

    Energy Technology Data Exchange (ETDEWEB)

    Ives, Robert Lawrence [Calabazas Creek Research, Inc.; Verboncoeur, John [University of California - Berkeley; Aldan, Manuel [University of California, Berkeley

    2010-05-30

    High voltage (HV) insulators are critical components in high-energy, accelerator and pulsed power systems that drive diverse applications in the national security, nuclear weapons science, defense and industrial arenas. In these systems, the insulator may separate vacuum/non-vacuum regions or conductors with high electrical field gradients. These insulators will often fail at electric fields over an order of magnitude lower than their intrinsic dielectric strength due to flashover at the dielectric interface. Decades of studies have produced a wealth of information on fundamental processes and mechanisms important for flashover initiation, but only for relatively simple insulator configurations in controlled environments. Accelerator and pulsed power system designers are faced with applying the fundamental knowledge to complex, operational devices with escalating HV requirements. Designers are forced to rely on “best practices” and expensive prototype testing, providing boundaries for successful operation. However, the safety margin is difficult to estimate, and system design must be very conservative for situations where testing is not practicable, or replacement of failed parts is disruptive or expensive. The Phase I program demonstrated the feasibility of developing an advanced code for modeling insulator breakdown. Such a code would be of great interest for a number of applications, including high energy physics, microwave source development, fusion sciences, and other research and industrial applications using high voltage devices.

  9. Climatologies at high resolution for the Earth land surface areas

    CERN Document Server

    Karger, Dirk Nikolaus; Böhner, Jürgen; Kawohl, Tobias; Kreft, Holger; Soria-Auza, Rodrigo Wilber; Zimmermann, Niklaus; Linder, H Peter; Kessler, Michael

    2016-01-01

    High resolution information of climatic conditions is essential to many application in environmental sciences. Here we present the CHELSA algorithm to downscale temperature and precipitation estimates from the European Centre for Medium-Range Weather Forecast (ECMWF) climatic reanalysis interim (ERA-Interim) to a high resolution of 30 arc sec. The algorithm for temperature is based on a statistical downscaling of atmospheric temperature from the ERA-Interim climatic reanalysis. The precipitation algorithm incorporates orographic predictors such as wind fields, valley exposition, and boundary layer height, and a bias correction using Global Precipitation Climatology Center (GPCC) gridded and Global Historical Climate Network (GHCN) station data. The resulting data consist of a monthly temperature and precipitation climatology for the years 1979-2013. We present a comparison of data derived from the CHELSA algorithm with two other high resolution gridded products with overlapping temporal resolution (Tropical R...

  10. Modified high-density lipoproteins by artificial sweetener, aspartame, and saccharin, showed loss of anti-atherosclerotic activity and toxicity in zebrafish.

    Science.gov (United States)

    Kim, Jae-Yong; Park, Ki-Hoon; Kim, Jihoe; Choi, Inho; Cho, Kyung-Hyun

    2015-01-01

    Safety concerns have been raised regarding the association of chronic consumption of artificial sweeteners (ASs) with metabolic disorders, especially in the heart and brain. There has been no information on the in vivo physiological effects of AS consumption in lipoprotein metabolism. High-dosage treatment (final 25, 50, and 100 mM) with AS (aspartame, acesulfame K, and saccharin) to human high-density lipoprotein (HDL) induced loss of antioxidant ability along with elevated atherogenic effects. Aspartame-treated HDL3 (final 100 mM) almost all disappeared due to putative proteolytic degradation. Aspartame- and saccharin-treated HDL3 showed more enhanced cholesteryl ester transfer activity, while their antioxidant ability was disappeared. Microinjection of the modified HDL3 exacerbated the inflammatory death in zebrafish embryos in the presence of oxLDL. These results show that AS treatment impaired the beneficial functions of HDL, resulting in loss of antioxidant and anti-atherogenic activities. These results suggest that aspartame and saccharin could be toxic to the human circulation system as well as embryonic development via impairment of lipoprotein function.

  11. High Density Sphere Culture of Adult Cardiac Cells Increases the Levels of Cardiac and Progenitor Markers and Shows Signs of Vasculogenesis

    Directory of Open Access Journals (Sweden)

    Kristina Vukusic

    2013-01-01

    Full Text Available 3D environment and high cell density play an important role in restoring and supporting the phenotypes of cells represented in cardiac tissues. The aim of this study was therefore to investigate the suitability of high density sphere (HDS cultures for studies of cardiomyocyte-, endothelial-, and stem-cell biology. Primary adult cardiac cells from nine human biopsies were cultured using different media for up to 9 weeks. The possibilities to favor a certain cell phenotype and induce production of extra cellular matrix (ECM were studied by histology, immunohistochemistry, and quantitative real-time PCR. Defined media gave significant increase in both cardiac- and progenitor-specific markers and also an intraluminal position of endothelial cells over time. Cardiac media showed indication of differentiation and maturity of HDS considering the ECM production and activities within NOTCH regulation but no additional cardiac differentiation. Endothelial media gave no positive effects on endothelial phenotype but increased proliferation without fibroblast overgrowth. In addition, indications for early vasculogenesis were found. It was also possible to affect the Wnt signaling in HDS by addition of a glycogen synthase kinase 3 (GSK3 inhibitor. In conclusion, these findings show the suitability of HDS as in vitro model for studies of cardiomyocyte-, endothelial-, and stem-cell biology.

  12. Development of high resolution land surface parameters for the Community Land Model

    Directory of Open Access Journals (Sweden)

    Y. Ke

    2012-11-01

    Full Text Available There is a growing need for high-resolution land surface parameters as land surface models are being applied at increasingly higher spatial resolution offline as well as in regional and global models. The default land surface parameters for the most recent version of the Community Land Model (i.e. CLM 4.0 are at 0.5° or coarser resolutions, released with the Community Earth System Model (CESM. Plant Functional Types (PFTs, vegetation properties such as Leaf Area Index (LAI, Stem Area Index (SAI, and non-vegetated land covers were developed using remotely sensed datasets retrieved in late 1990's and the beginning of this century. In this study, we developed new land surface parameters for CLM 4.0, specifically PFTs, LAI, SAI and non-vegetated land cover composition, at 0.05° resolution globally based on the most recent MODIS land cover and improved MODIS LAI products. Compared to the current CLM 4.0 parameters, the new parameters produced a decreased coverage by bare soil and trees, but an increased coverage by shrub, grass, and cropland. The new parameters result in a decrease in global seasonal LAI, with the biggest decrease in boreal forests; however, the new parameters also show a large increase in LAI in tropical forest. Differences between the new and the current parameters are mainly caused by changes in the sources of remotely sensed data and the representation of land cover in the source data. Advantages and disadvantages of each dataset were discussed in order to provide guidance on the use of the data. The new high-resolution land surface parameters have been used in a coupled land-atmosphere model (WRF-CLM applied to the western US to demonstrate their use in high-resolution modeling. A remapping method from the latitude/longitude grid of the CLM data to the WRF grids with map projection was also demonstrated. Future work will include global offline CLM simulations to examine the impacts of source data resolution and subsequent land

  13. Polymer surface functionalities that control human embryoid body cell adhesion revealed by high throughput surface characterization of combinatorial material microarrays.

    Science.gov (United States)

    Yang, Jing; Mei, Ying; Hook, Andrew L; Taylor, Michael; Urquhart, Andrew J; Bogatyrev, Said R; Langer, Robert; Anderson, Daniel G; Davies, Martyn C; Alexander, Morgan R

    2010-12-01

    High throughput materials discovery using combinatorial polymer microarrays to screen for new biomaterials with new and improved function is established as a powerful strategy. Here we combine this screening approach with high throughput surface characterization (HT-SC) to identify surface structure-function relationships. We explore how this combination can help to identify surface chemical moieties that control protein adsorption and subsequent cellular response. The adhesion of human embryoid body (hEB) cells to a large number (496) of different acrylate polymers synthesized in a microarray format is screened using a high throughput procedure. To determine the role of the polymer surface properties on hEB cell adhesion, detailed HT-SC of these acrylate polymers is carried out using time of flight secondary ion mass spectrometry (ToF SIMS), X-ray photoelectron spectroscopy (XPS), pico litre drop sessile water contact angle (WCA) measurement and atomic force microscopy (AFM). A structure-function relationship is identified between the ToF SIMS analysis of the surface chemistry after a fibronectin (Fn) pre-conditioning step and the cell adhesion to each spot using the multivariate analysis technique partial least squares (PLS) regression. Secondary ions indicative of the adsorbed Fn correlate with increased cell adhesion whereas glycol and other functionalities from the polymers are identified that reduce cell adhesion. Furthermore, a strong relationship between the ToF SIMS spectra of bare polymers and the cell adhesion to each spot is identified using PLS regression. This identifies a role for both the surface chemistry of the bare polymer and the pre-adsorbed Fn, as-represented in the ToF SIMS spectra, in controlling cellular adhesion. In contrast, no relationship is found between cell adhesion and wettability, surface roughness, elemental or functional surface composition. The correlation between ToF SIMS data of the surfaces and the cell adhesion demonstrates

  14. Hedgehog signaling pathway is active in GBM with GLI1 mRNA expression showing a single continuous distribution rather than discrete high/low clusters.

    Directory of Open Access Journals (Sweden)

    Vikas Chandra

    Full Text Available Hedgehog (Hh signaling pathway is a valid therapeutic target in a wide range of malignancies. We focus here on glioblastoma multiforme (GBM, a lethal malignancy of the central nervous system (CNS. By analyzing RNA-sequencing based transcriptomics data on 149 clinical cases of TCGA-GBM database we show here a strong correlation (r = 0.7 between GLI1 and PTCH1 mRNA expression--as a hallmark of the canonical Hh-pathway activity in this malignancy. GLI1 mRNA expression varied in 3 orders of magnitude among the GBM patients of the same cohort showing a single continuous distribution-unlike the discrete high/low-GLI1 mRNA expressing clusters of medulloblastoma (MB. When compared with MB as a reference, the median GLI1 mRNA expression in GBM appeared 14.8 fold lower than that of the "high-Hh" cluster of MB but 5.6 fold higher than that of the "low-Hh" cluster of MB. Next, we demonstrated statistically significant up- and down-regulation of GLI1 mRNA expressions in GBM patient-derived low-passage neurospheres in vitro by sonic hedgehog ligand-enriched conditioned media (shh-CM and by Hh-inhibitor drug vismodegib respectively. We also showed clinically achievable dose (50 μM of vismodegib alone to be sufficient to induce apoptosis and cell cycle arrest in these low-passage GBM neurospheres in vitro. Vismodegib showed an effect on the neurospheres, both by down-regulating GLI1 mRNA expression and by inducing apoptosis/cell cycle arrest, irrespective of their relative endogenous levels of GLI1 mRNA expression. We conclude from our study that this single continuous distribution pattern of GLI1 mRNA expression technically puts almost all GBM patients in a single group rather than discrete high- or low-clusters in terms of Hh-pathway activity. That is suggestive of therapies with Hh-pathway inhibitor drugs in this malignancy without a need for further stratification of patients on the basis of relative levels of Hh-pathway activity among them.

  15. Study of surface leakage current of AlGaN/GaN high electron mobility transistors

    Energy Technology Data Exchange (ETDEWEB)

    Chen, YongHe; Zhang, Kai; Cao, MengYi; Zhao, ShengLei; Zhang, JinCheng; Hao, Yue, E-mail: yhao@xidian.edu.cn [Key Laboratory of Wide Band Gap Semiconductor Materials and Devices, School of Microelectronics, Xidian University, Xi' an 710071 (China); Ma, XiaoHua, E-mail: xhma@xidian.edu.cn [Key Laboratory of Wide Band Gap Semiconductor Materials and Devices, School of Microelectronics, Xidian University, Xi' an 710071 (China); School of Advanced Materials and Nanotechnology, Xidian University, Xi' an 710071 (China)

    2014-04-14

    Temperature-dependent surface current measurements were performed to analyze the mechanism of surface conductance of AlGaN/GaN channel high-electron-mobility transistors by utilizing process-optimized double gate structures. Different temperatures and electric field dependence have been found in surface current measurements. At low electric field, the mechanism of surface conductance is considered to be two-dimensional variable range hopping. At elevated electric field, the Frenkel–Poole trap assisted emission governs the main surface electrons transportation. The extracted energy barrier height of electrons emitting from trapped state near Fermi energy level into a threading dislocations-related continuum state is 0.38 eV. SiN passivation reduces the surface leakage current by two order of magnitude and nearly 4 orders of magnitude at low and high electric fields, respectively. SiN also suppresses the Frenkel–Poole conductance at high temperature by improving the surface states of AlGaN/GaN. A surface treatment process has been introduced to further suppress the surface leakage current at high temperature and high field, which results in a decrease in surface current of almost 3 orders of magnitude at 476 K.

  16. Surface Plasmons on Highly Doped InP

    DEFF Research Database (Denmark)

    Panah, Mohammad Esmail Aryaee; Ottaviano, Luisa; Semenova, Elizaveta

    2016-01-01

    Silicon doped InP is grown by metal-organic vapor phase epitaxy (MOVPE) using optimized growth parameters to achieve high free carrier concentration. Reflectance of the grown sample in mid-IR range is measured using FTIR and the result is used to retrieve the parameters of the dielectric function...

  17. A Liquid Inorganic Electrolyte Showing an Unusually High Lithium Ion Transference Number: A Concentrated Solution of LiAlCl4 in Sulfur Dioxide

    Directory of Open Access Journals (Sweden)

    Martin Winter

    2013-08-01

    Full Text Available We report on studies of an inorganic electrolyte: LiAlCl4 in liquid sulfur dioxide. Concentrated solutions show a very high conductivity when compared with typical electrolytes for lithium ion batteries that are based on organic solvents. Our investigations include conductivity measurements and measurements of transference numbers via nuclear magnetic resonance (NMR and by a classical direct method, Hittorf’s method. For the use of Hittorf’s method, it is necessary to measure the concentration of the electrolyte in a selected cell compartment before and after electrochemical polarization very precisely. This task was finally performed by potentiometric titration after hydrolysis of the salt. The Haven ratio was determined to estimate the association behavior of this very concentrated electrolyte solution. The measured unusually high transference number of the lithium cation of the studied most concentrated solution, a molten solvate LiAlCl4 × 1.6SO2, makes this electrolyte a promising alternative for lithium ion cells with high power ability.

  18. High resolution land surface geophysical parameters estimation from ALOS PALSAR data

    Science.gov (United States)

    High resolution land surface geophysical products, such as soil moisture, surface roughness and vegetation water content, are essential for a variety of applications ranging from water management to regional climate predictions. In India high resolution geophysical products, in particular soil moist...

  19. INVESTIGATION OF HIGH-CURRENT INTERRUPTING CONTACTS WORKING SURFACES MECHANICAL INTERACTION NATURE

    Directory of Open Access Journals (Sweden)

    O.G. Volkova

    2016-03-01

    Full Text Available Introduction. The nature of the interaction of high-working surfaces of the electrical contact uniquely affects their performance. By the failure of the contacts in the main drive processes resulting from complex destructive factors affecting their performance. However, not all processes are studied in detail and give in modeling. The purpose of the paper is to show the possibility of using the method of holographic interferometry to estimate the plastic deformation in the zone of contact interaction. One of the significant factors affecting the work of the contact pair is the compressive force of the contact surfaces. Compression discontinuous contact is directly connected with the processes of elastic and plastic deformation of the contact material, which is particularly evident in the contact details of the powder or composite materials. The paper focuses on the plastic deformation of the surface layers of discontinuous contact in circuit, it is believed that it is directly related to the mechanism of conductivity of contacts. As shown, a significant effect on the deformation of the contact surfaces and renders the working environment, in particular transformer oil. Methodology. Assessing the impact of compression forces on the deformation of the contact surface was conducted experimentally using the method of holographic interferometry. Results. Experimental studies, which indicated that the compact and powder materials plastic deformation in and around the area microcontacts simplistically stated that requires experimental verification. A method for evaluating the state of stress, which affects the formation and destruction of the local contact spots. Practical value. Using the experimental method of determining the movement of the contact region allows you to optimize discontinuous contacts from composite and powder materials.

  20. Turbulent boundary layer measurements over high-porosity surfaces

    Science.gov (United States)

    Efstathiou, Christoph; Luhar, Mitul

    2016-11-01

    Porous surfaces are ubiquitous across a variety of turbulent boundary layer flows of scientific and engineering interest. While turbulent flows over smooth and rough walls have been studied extensively, experimental measurements over porous walls have thus far focused on packed beds, which are limited in porosity (Φ = 0 . 3 - 0 . 5) by their geometry. The current project seeks to address this limitation. A two-component laser doppler velocimeter (LDV) is used to generate velocity measurements in turbulent boundary layer flows over commercially available reticulated foams and 3D-printed porous media at Reynolds number Reθ 3000 - 4000 . Smooth wall profiles for mean and turbulent quantities are compared to data over substrates with porosity Φ > 0 . 8 and average pore sizes in the range 0.4-2.5mm (corresponding to 8 - 50 viscous units). Previous analytical and simulation efforts indicate that the effects of porous substrates on boundary layer flows depend on a modified Reynolds number defined using the length scale √{ κ}, where κ is substrate permeability. A custom permeameter is currently being developed to estimate κ for the substrates tested in the boundary layer experiments.

  1. Different methods to alter surface morphology of high aspect ratio structures

    Energy Technology Data Exchange (ETDEWEB)

    Leber, M., E-mail: moritz.leber@utah.edu [Department of Electrical and Computer Engineering, University of Utah, Salt Lake City, UT (United States); Shandhi, M.M.H. [Department of Electrical and Computer Engineering, University of Utah, Salt Lake City, UT (United States); Hogan, A. [Blackrock Microsystems, Salt Lake City, UT (United States); Solzbacher, F. [Department of Electrical and Computer Engineering, University of Utah, Salt Lake City, UT (United States); Bhandari, R.; Negi, S. [Department of Electrical and Computer Engineering, University of Utah, Salt Lake City, UT (United States); Blackrock Microsystems, Salt Lake City, UT (United States)

    2016-03-01

    Graphical abstract: Surface engineering of high aspect ratio silicon structures. - Highlights: • Multiple roughening techniques for high aspect ratio devices were investigated. • Modification of surface morphology of high aspect ratio silicon devices (1:15). • Decrease of 76% in impedance proves significant increase in surface area. - Abstract: In various applications such as neural prostheses or solar cells, there is a need to alter the surface morphology of high aspect ratio structures so that the real surface area is greater than geometrical area. The change in surface morphology enhances the devices functionality. One of the applications of altering the surface morphology is of neural implants such as the Utah electrode array (UEA) that communicate with single neurons by charge injection induced stimulation or by recording electrical neural signals. For high selectivity between single cells of the nervous system, the electrode surface area is required to be as small as possible, while the impedance is required to be as low as possible for good signal to noise ratios (SNR) during neural recording. For stimulation, high charge injection and charge transfer capacities of the electrodes are required, which increase with the electrode surface. Traditionally, researchers have worked with either increasing the roughness of the existing metallization (platinum grey, black) or other materials such as Iridium Oxide and PEDOT. All of these previously investigated methods lead to more complicated metal deposition processes that are difficult to control and often have a critical impact on the mechanical properties of the metal films. Therefore, a modification of the surface underneath the electrode's coating will increase its surface area while maintaining the standard and well controlled metal deposition process. In this work, the surfaces of the silicon micro-needles were engineered by creating a defined microstructure on the electrodes surface using several

  2. Evaluation of cutting force and surface roughness in high-speed milling of compacted graphite iron

    Directory of Open Access Journals (Sweden)

    Azlan Suhaimi Mohd

    2017-01-01

    Full Text Available Compacted Graphite Iron, (CGI is known to have outstanding mechanical strength and weight-to-strength ratio as compared to conventional grey cast iron, (CI. The outstanding characteristics of CGI is due to its graphite particle shape, which is presented as compacted vermicular particle. The graphite is interconnected with random orientation and round edges, which results in higher mechanical strength. Whereas, graphite in the CI consists of a smooth-surfaced flakes that easily propagates cracks which results in weaker and brittle properties as compared to CGI. Owing to its improved properties, CGI is considered as the best candidate material in substituting grey cast iron that has been used in engine block applications for years. However, the smooth implementation of replacing CI with CGI has been hindered due to the poor machinability of CGI especially at high cutting speed. The tool life is decreased by 20 times when comparing CGI with CI under the same cutting condition. This study investigates the effect of using cryogenic cooling and minimum quantity lubrication (MQL during high-speed milling of CGI (grade 450. Results showed that, the combination of internal cryogenic cooling and enhanced MQL improved the tool life, cutting force and surface quality as compared to the conventional flood coolant strategy during high-speed milling of CGI.

  3. a High-Performance Method for Simulating Surface Rainfall-Runoff Dynamics Using Particle System

    Science.gov (United States)

    Zhang, Fangli; Zhou, Qiming; Li, Qingquan; Wu, Guofeng; Liu, Jun

    2016-06-01

    The simulation of rainfall-runoff process is essential for disaster emergency and sustainable development. One common disadvantage of the existing conceptual hydrological models is that they are highly dependent upon specific spatial-temporal contexts. Meanwhile, due to the inter-dependence of adjacent flow paths, it is still difficult for the RS or GIS supported distributed hydrological models to achieve high-performance application in real world applications. As an attempt to improve the performance efficiencies of those models, this study presents a high-performance rainfall-runoff simulating framework based on the flow path network and a separate particle system. The vector-based flow path lines are topologically linked to constrain the movements of independent rain drop particles. A separate particle system, representing surface runoff, is involved to model the precipitation process and simulate surface flow dynamics. The trajectory of each particle is constrained by the flow path network and can be tracked by concurrent processors in a parallel cluster system. The result of speedup experiment shows that the proposed framework can significantly improve the simulating performance just by adding independent processors. By separating the catchment elements and the accumulated water, this study provides an extensible solution for improving the existing distributed hydrological models. Further, a parallel modeling and simulating platform needs to be developed and validate to be applied in monitoring real world hydrologic processes.

  4. HIGH AND LOW RESOLUTION TEXTURED MODELS OF COMPLEX ARCHITECTURAL SURFACES

    Directory of Open Access Journals (Sweden)

    E. K. Stathopoulou

    2012-09-01

    Full Text Available During the recent years it has become obvious that 3D technology, applied mainly with the use of terrestrial laser scanners (TLS is the most suitable technique for the complete geometric documentation of complex objects, whether they are monuments or architectural constructions in general. However, it is rather a challenging task to convert an acquired point cloud into a realistic 3D polygonal model that can simultaneously satisfy high resolution modeling and visualization demands. The aim of the visualization of a simple or complex object is to create a 3D model that best describes the reality within the computer environment. This paper is dedicated especially in the visualization of a complex object's 3D model, through high, as well as low resolution textured models. The object of interest for this study was the Almoina (Romanesque Door of the Cathedral of Valencia in Spain.

  5. High and Low Resolution Textured Models of Complex Architectural Surfaces

    Science.gov (United States)

    Stathopoulou, E. K.; Valanis, A.; Lerma, J. L.; Georgopoulos, A.

    2011-09-01

    During the recent years it has become obvious that 3D technology, applied mainly with the use of terrestrial laser scanners (TLS) is the most suitable technique for the complete geometric documentation of complex objects, whether they are monuments or architectural constructions in general. However, it is rather a challenging task to convert an acquired point cloud into a realistic 3D polygonal model that can simultaneously satisfy high resolution modeling and visualization demands. The aim of the visualization of a simple or complex object is to create a 3D model that best describes the reality within the computer environment. This paper is dedicated especially in the visualization of a complex object's 3D model, through high, as well as low resolution textured models. The object of interest for this study was the Almoina (Romanesque) Door of the Cathedral of Valencia in Spain.

  6. Survivability of bare, individual Bacillus subtilis spores to high-velocity surface impact: Implications for microbial transfer through space

    Science.gov (United States)

    Barney, Brandon L.; Pratt, Sara N.; Austin, Daniel E.

    2016-06-01

    Laboratory experiments show that endospores of Bacillus subtilis survive impact against a solid surface at velocities as high as 299 ±28 m/s. During impact, spores experience and survive accelerations of at least 1010 m/s2. The spores were introduced into a vacuum chamber using an electrospray source and accelerated to a narrow velocity distribution by entrainment in a differentially pumped gas flow. Different velocity ranges were studied by modifying the gas flow parameters. The spores were electrically charged, allowing direct measurement of the velocity of each spore as it passed through an image charge detector prior to surface impact. Spores impacted a glass surface and were collected for subsequent analysis by culturing. Most spores survived impact at all measured velocities. These experiments differ fundamentally from other studies that show either shock or impact survivability of bacteria embedded within or on the surface of a projectile. Bacteria in the present experiments undergo a single interaction with a solid surface at the full impact velocity, in the absence of any other effects such as cushioning due to microbe agglomerations, deceleration due to air or vapor, or transfer of impact shock through solid or liquid media. During these full-velocity impact events, the spores experience extremely high decelerations. This study is the first reported instance of accelerations of this magnitude experienced during a bacteria impact event. These results are discussed in the context of potential transfer of viable microbes in space and other scenarios involving surface impacts at high velocities.

  7. High throughput functional epitope mapping: revisiting phage display platform to scan target antigen surface.

    Science.gov (United States)

    Rojas, Gertrudis; Tundidor, Yaima; Infante, Yanelys Cabrera

    2014-01-01

    Antibody engineering must be accompanied by mapping strategies focused on identifying the epitope recognized by each antibody to define its unique functional identity. High throughput fine specificity determination remains technically challenging. We review recent experiences aimed at revisiting the oldest and most extended display technology to develop a robust epitope mapping platform, based on the ability to manipulate target-derived molecules (ranging from the whole native antigen to antigen domains and smaller fragments) on filamentous phages. Single, multiple and combinatorial mutagenesis allowed comprehensive scanning of phage-displayed antigen surface that resulted in the identification of clusters of residues contributing to epitope formation. Functional pictures of the epitope(s) were thus delineated in the natural context. Successful mapping of antibodies against interleukin-2, epidermal growth factor and its receptor, and vascular endothelial growth factor showed the versatility of these procedures, which combine the accuracy of site-directed mutagenesis with the high throughput potential of phage display.

  8. Molecularly imprinted polymers for highly sensitive detection of morphine using surface plasmon resonance spectroscopy

    Institute of Scientific and Technical Information of China (English)

    Hong Xia Hao; Hong Zhou; Jing Chang; Jun Zhu; Tian Xin Wei

    2011-01-01

    Molecular imprinting technology is applied in surface plasmon resonance spectroscopy for highly sensitive and selective detection of morphine (MO). As SPR-based sensor of MO, the preparation of molecular imprinted polymer is as follows: methacrylic acids (MAA), ethylene glycol dimethacrylate (EGDMA), azodiisobutyronitrile (AIBN) were used as functional monomer, cross-linker and initiator, respectively. The experiment results showed that morphine imprinted polymer had the performance of high sensitivity and specificity, i.e. the relative signal of SPR response was proportional to the concentration of morphine in acetonitrile in the range of 10-9 mol/L to 10-6mol/L (1 ppb-1 ppm) with LOD of 10-10mol/L, and MO was distinguished from its analogs, such as codeine.

  9. High-order spoof localized surface plasmons supported on a complementary metallic spiral structure

    Science.gov (United States)

    Gao, Zhen; Gao, Fei; Zhang, Baile

    2016-01-01

    We experimentally demonstrate that multiple high-order spoof localized surface plasmons (spoof-LSPs) modes can be supported on a complementary metallic spiral structure, which were absent in the previously reported spoof-LSPs modes. Through exact numerical simulations and near-field imaging experiments, we directly observe these high-order spoof-LSPs modes at microwave frequencies. We also show that these higher-order spoof-LSPs modes exhibit larger frequency shifts caused by the local environmental refractive index change than the previously reported low-order spoof-LSPs modes. Hence the complementary MSS may find potential applications as plasmonic sensor in the microwave and terahertz frequencies. PMID:27079658

  10. Surface-diffusion-driven decay of high-aspect-ratio gratings: existence of morphologically related classes.

    Science.gov (United States)

    Madrid, Marcos A; Salvarezza, Roberto C; Castez, Marcos F

    2013-06-01

    We present numerical and theoretical results concerning the technologically important process of evolution of high-aspect-ratio profiles due to surface diffusion under thermal treatment. We show how a broad class of initial gratings adopt, after a short transient stage, a typical shape that can be accurately described as a curve whose curvature has only two single Fourier modes as a function of the arc-length parameter. Moreover, we introduce a set of evolution equations for the relevant parameters that accounts very accurately for both morphological and kinetic aspects of the transformation processes for these curves in a wide region in parameter space. Regarding the decay of rectangular gratings, our numerical results show the existence of geometrically related classes that asymptotically approach to the same trajectory in parameter space. Gratings belonging to the same class pass through the same sequence of morphologies before reaching the final equilibrium state.

  11. Morphological and animal study of titanium dental implant surface induced by blasting and high intensity pulsed Nd-glass laser

    Energy Technology Data Exchange (ETDEWEB)

    Karacs, A.; Joob Fancsaly, A.; Divinyi, T.; Peto, G.; Kovach, G

    2003-03-03

    Machined dental implants of titanium were blasted with Al{sub 2}O{sub 3} powder of 250 {mu}m particle size. The surface was irradiated in vacuum with a Nd-glass pulsed laser at 1-3 J pulse energies. The morphology of these surfaces was investigated by optical and scanning electron microscopy. The low intensity laser treatment resulted in some new irregularities but we can observe the blasted elements and caves from the original blasted surface too. The blasted elements were washed out and a new surface morphology was induced by the high intensity laser treatment. The osseointegration was determined by measuring the removal torque in the rabbit experiments. The results were referred to the as machined surface. The blasting slightly increased the removal torque. The laser irradiation increased the removal torque significantly, more by a factor of 1.5 compared to the reference at high laser intensity. This shows the influence of the surface morphology on the osseointegration. The combination of the blasting with the laser irradiation is considered a method to determine the morphology optimal for the osseointegration because the pulsed laser irradiation caused modifications of the micrometer sized surface elements and decreases possible surface contamination.

  12. Surface Integrity and Structural Stability of Broached Inconel 718 at High Temperatures

    Science.gov (United States)

    Chen, Z.; Peng, R. Lin; Moverare, J.; Avdovic, P.; Zhou, J. M.; Johansson, S.

    2016-07-01

    The current study focused on the surface integrity issues associated with broaching of Inconel 718 and the structural stability of the broached specimen at high temperatures, mainly involving the microstructural changes and residual stress relaxation. The broaching operation was performed using similar cutting conditions as that used in turbo machinery industries for machining fir-tree root fixings on turbine disks. Thermal exposure was conducted at 723 K, 823 K, and 923 K (450 °C, 550 °C, and 650 °C) for 30, 300, and 3000 hours, respectively. Surface cavities and debris dragging, sub-surface cracks, high intensity of plastic deformation, as well as the generation of tensile residual stresses were identified to be the main issues in surface integrity for the broached Inconel 718. When a subsequent heating was applied, surface recrystallization and α-Cr precipitation occurred beneath the broached surface depending on the applied temperature and exposure time. The plastic deformation induced by the broaching is responsible for these microstructural changes. The surface tension was completely relaxed in a short time at the temperature where surface recrystallization occurred. The tensile layer on the sub-surface, however, exhibited a much higher resistance to the stress relief annealing. Oxidation is inevitable at high temperatures. The study found that the surface recrystallization could promote the local Cr diffusion on the broached surface.

  13. How to Show the Real Microbial Biodiversity? A Comparison of Seven DNA Extraction Methods for Bacterial Population Analyses in Matrices Containing Highly Charged Natural Nanoparticles.

    Science.gov (United States)

    Kaden, Rene; Krolla-Sidenstein, Peter

    2015-10-20

    A DNA extraction that comprises the DNA of all available taxa in an ecosystem is an essential step in population analysis, especially for next generation sequencing applications. Many nanoparticles as well as naturally occurring clay minerals contain charged surfaces or edges that capture negatively charged DNA molecules after cell lysis within DNA extraction. Depending on the methodology of DNA extraction, this phenomenon causes a shift in detection of microbial taxa in ecosystems and a possible misinterpretation of microbial interactions. With the aim to describe microbial interactions and the bio-geo-chemical reactions during a clay alteration experiment, several methods for the detection of a high number of microbial taxa were examined in this study. Altogether, 13 different methods of commercially available DNA extraction kits provided by seven companies as well as the classical phenol-chloroform DNA extraction were compared. The amount and the quality of nucleic acid extracts were determined and compared to the amplifiable amount of DNA. The 16S rRNA gene fragments of several taxa were separated using denaturing gradient gel electrophoresis (DGGE) to determine the number of different species and sequenced to get the information about what kind of species the microbial population consists of. A total number of 13 species was detected in the system. Up to nine taxa could be detected with commercially available DNA extraction kits while phenol-chloroform extraction lead to three detected species. In this paper, we describe how to combine several DNA extraction methods for the investigation of microbial community structures in clay.

  14. How to Show the Real Microbial Biodiversity? A Comparison of Seven DNA Extraction Methods for Bacterial Population Analyses in Matrices Containing Highly Charged Natural Nanoparticles

    Directory of Open Access Journals (Sweden)

    Rene Kaden

    2015-10-01

    Full Text Available A DNA extraction that comprises the DNA of all available taxa in an ecosystem is an essential step in population analysis, especially for next generation sequencing applications. Many nanoparticles as well as naturally occurring clay minerals contain charged surfaces or edges that capture negatively charged DNA molecules after cell lysis within DNA extraction. Depending on the methodology of DNA extraction, this phenomenon causes a shift in detection of microbial taxa in ecosystems and a possible misinterpretation of microbial interactions. With the aim to describe microbial interactions and the bio-geo-chemical reactions during a clay alteration experiment, several methods for the detection of a high number of microbial taxa were examined in this study. Altogether, 13 different methods of commercially available DNA extraction kits provided by seven companies as well as the classical phenol-chloroform DNA extraction were compared. The amount and the quality of nucleic acid extracts were determined and compared to the amplifiable amount of DNA. The 16S rRNA gene fragments of several taxa were separated using denaturing gradient gel electrophoresis (DGGE to determine the number of different species and sequenced to get the information about what kind of species the microbial population consists of. A total number of 13 species was detected in the system. Up to nine taxa could be detected with commercially available DNA extraction kits while phenol-chloroform extraction lead to three detected species. In this paper, we describe how to combine several DNA extraction methods for the investigation of microbial community structures in clay.

  15. Highly virulent Beauveria bassiana strains against the two-spotted spider mite, Tetranychus urticae, show no pathogenicity against five phytoseiid mite species.

    Science.gov (United States)

    Wu, Shengyong; Xie, Haicui; Li, Maoye; Xu, Xuenong; Lei, Zhongren

    2016-12-01

    Entomopathogenic fungi and predatory mites can independently contribute to suppressing the two-spotted spider mite, Tetranychus urticae Koch. It is important to assess the risk of possible fungal infections in predators when a combination of them are being considered as a tandem control strategy for suppressing T. urticae. The first part of this study tested 12 Beauveria bassiana isolates for virulence in T. urticae. Strains SCWJ-2, SDDZ-9, LNSZ-26, GZGY-1-3 and WLMQ-32 were found to be the most potent, causing 37.6-49.5% adult corrected mortality at a concentration of 1 × 10(7) m/L conidia 4 days post-treatment. The second part evaluated the pathogenicity of these five strains in five species of predatory phytoseiid mites. The bioassay results indicated that all adult predatory mite mortalities ranged from 7.5 to 9.1% 4 days post-treatment. No viable fungal hyphae were found on predator cadavers. Observations with scanning electron microscopy revealed that conidia were attached to the cuticle of predatory mites within 2-12 h after spraying with strain LNSZ-26, and had germinated within 24-36 h. After 48 h, conidia had gradually been shed from the mites, after none of the conidia had penetrated the cuticular surfaces. In contrast, the germinated conidia successfully penetrated the cuticle of T. urticae, and within 60 h the fungus colonized the mite's body. Our study demonstrated that although several B. bassiana strains displayed a high virulence in T. urticae there was no evident pathogenicity to phytoseiid mites. These findings support the potential use of entomopathogenic fungus in combination with predatory mites in T. urticae control programs.

  16. Highly bioactive polysiloxane modified bioactive glass-poly(ethylene glycol) hybrids monoliths with controlled surface structure for bone tissue regeneration

    Science.gov (United States)

    Chen, Jing; Que, Wenxiu; Xing, Yonglei; Lei, Bo

    2015-03-01

    Crack-free monoliths with controllable surface microstructure have high bioactivities and therefore potential applications in bone tissue regeneration. In this paper, crack-free polydimethylsiloxane-modified bioactive glass-poly (ethylene glycol) (PDMS-BG-PEG) hybrids monoliths were fabricated via using a modified sol-gel process. Results show that the addition of PEG plays an important part in the formation of crack-free and gelation of the monoliths, and surface microstructures of the as-prepared hybrid monoliths were significantly influenced by the concentration and molecular weight of PEG. The samples obtained from PEG 300 had porous surface result in higher bioactivity (apatite formation) in simulated body fluid (SBF), while the samples obtained from PEG 600 had the smooth surface and inhibited the formation of apatite layer in SBF. These as-prepared hybrid monoliths can be used as a good candidate of implant and scaffold for highly efficient bone tissue regeneration.

  17. Preparation of High-Surface Area Nano-CeO2 by Template-Assisted Precipitation Method

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The high-surface area nano-CeO2 was prepared by Ce(NO3)3 by precipitation method, with surfactant cetyltrimethyl ammonium bromide (CTAB) as templating agent. The effects of the precipitating agents, reaction temperature, ageing time, and calcination temperature on the surface area, as well as the pore structure and the mean crystallite size of nano-CeO2 were studied. It was found that the reaction of Ce(NO3)3 with NaOH in the presence of CTAB at 90 ℃ for 12 h yieldsed a cerium oxide/surfactant mixture, which after calcination at 400 ℃ resulted in high-surface area nano-CeO2. The mean crystallite size of CeO2 was approximately 6 nm, surface area was in excess of 200 m2·g-1, pore size was approximately 9 nm, and the pore distribution was concentrative. Moreover, the surface area can still reach 147 m2·g-1 after calcination at 700 ℃, which showed the good thermal stability of the CeO2. The number of oxygen vacancies in the structure of CeO2 corresponded with the surface area of CeO2, and the high surface area was propitious to the formation of oxygen vacancies.

  18. Exoplanet transits enable high-resolution spectroscopy across spatially resolved stellar surfaces

    CERN Document Server

    Dravins, Dainis; Dahlén, Erik; Pazira, Hiva

    2016-01-01

    Observations of stellar surfaces - except for the Sun - are hampered by their tiny angular extent, while observed spectral lines are smeared by averaging over the stellar surface, and by stellar rotation. Exoplanet transits can be used to analyze stellar atmospheric structure, yielding high-resolution spectra across spatially highly resolved stellar surfaces, free from effects of spatial smearing and the rotational wavelength broadening present in full-disk spectra. During a transit, stellar surface portions successively become hidden, and differential spectroscopy between various transit phases provides spectra of those surface segments then hidden behind the planet. The small area subtended by even a large planet (about 1% of a main-sequence star) offers high spatial resolution but demands very precise observations. We demonstrate the reconstruction of photospheric FeI line profiles at a spectral resolution R=80,000 across the surface of the solar-type star HD209458. Any detailed understanding of stellar at...

  19. Oxygen concentration control of dopamine-induced high uniformity surface coating chemistry.

    Science.gov (United States)

    Kim, Hyo Won; McCloskey, Bryan D; Choi, Tae Hwan; Lee, Changho; Kim, Min-Joung; Freeman, Benny D; Park, Ho Bum

    2013-01-23

    Material surface engineering has attracted great interest in important applications, including electronics, biomedicine, and membranes. More recently, dopamine has been widely exploited in solution-based chemistry to direct facile surface modification. However, unsolved questions remain about the chemical identity of the final products, their deposition kinetics and their binding mechanism. In particular, the dopamine oxidation reaction kinetics is a key to improving surface modification efficiency. Here, we demonstrate that high O(2) concentrations in the dopamine solution lead to highly homogeneous, thin layer deposition on any material surfaces via accelerated reaction kinetics, elucidated by Le Chatelier's principle toward dopamine oxidation steps in a Michael-addition reaction. As a result, highly uniform, ultra-smooth modified surfaces are achieved in much shorter deposition times. This finding provides new insights into the effect of reaction kinetics and molecular geometry on the uniformity of modifications for surface engineering techniques.

  20. Chemometric analysis of chromatographic fingerprints shows potential of Cyclopia maculata (Andrews) Kies for production of standardized extracts with high xanthone content.

    Science.gov (United States)

    Schulze, Alexandra E; de Beer, Dalene; de Villiers, André; Manley, Marena; Joubert, Elizabeth

    2014-10-29

    Cyclopia species are used for the production of honeybush tea and food ingredient extracts associated with many health benefits. A species-specific high-performance liquid chromatography (HPLC) method for Cyclopia maculata, developed and validated, allowed quantification of the major compounds in extracts from "unfermented" and fermented C. maculata. Two xanthones were tentatively identified for the first time in a Cyclopia species, whereas an additional four compounds were tentatively identified for the first time in C. maculata. "Fermentation" (oxidation) decreased the content of all compounds, with the exception of vicenin-2. Similarity analysis of the chromatographic fingerprints of unfermented C. maculata aqueous extracts showed extremely low variation (r ≥ 0.97) between samples. Some differences between wild-harvested and cultivated seedling plants were, however, demonstrated using principal component analysis. Quantitative data of selected compounds confirmed the low level of variation, making this Cyclopia species ideal for the production of standardized food ingredient extracts.

  1. High resolution scanning electron microscopy of rabbit corneal endothelium to show effects of UV-visible irradiation in the presence of chlorpromazine

    Energy Technology Data Exchange (ETDEWEB)

    Lea, P.J.; Hollenberg, M.J.; Menon, I.A.; Temkin, R.J.; Persad, S.D.; Basu, P.K. (Univ. of Toronto, Ontario (Canada))

    1989-01-01

    The ultrastructure of rabbit cornea endothelial cells was examined by scanning electron microscopy (SEM) in freeze-cleaved corneas using a Hitachi S-570 scanning electron microscope in the high resolution mode (HRSEM). In order to study phototoxic effects in vitro, rabbit corneas (experimental) were cultured as organ culture in the presence of 5 micrograms/ml chlorpromazine (CPZ) and irradiated. For comparison, control 1 corneas were not irradiated but incubated in the dark without CPZ in the medium; control 2 corneas were also kept in the dark but in the presence of CPZ; control 3 corneas were irradiated with no CPZ in the medium. Cellular damage was not seen in the three types of control corneas, but in the experimental corneas the endothelial cells showed extensive disruption of the cell membrane and some deterioration of the intracellular components. Our study confirmed that HRSEM is a satisfactory new technique for visualizing damage of the intracellular organelles of corneal endothelium.

  2. Breeding loggerhead marine turtles Caretta caretta in Dry Tortugas National Park, USA, show high fidelity to diverse habitats near nesting beaches

    Science.gov (United States)

    Hart, Kristen M.; Zawada, David G.; Sartain-Iverson, Autumn R.; Fujisaki, Ikuko

    2016-01-01

    We used satellite telemetry to identify in-water habitat used by individuals in the smallest North-west Atlantic subpopulation of adult nesting loggerhead turtles Caretta caretta during the breeding season. During 2010, 2011 and 2012 breeding periods, a total of 20 adult females used habitats proximal to nesting beaches with various levels of protection within Dry Tortugas National Park. We then used a rapid, high-resolution, digital imaging system to map habitat adjacent to nesting beaches, revealing the diversity and distribution of available benthic cover. Turtle behaviour showing measurable site-fidelity to these diverse habitats has implications for managing protected areas and human activities within them. Protecting diverse benthic areas adjacent to loggerhead turtle nesting beaches here and elsewhere could provide benefits for overall biodiversity conservation.

  3. High Heat Flux Surface Coke Deposition and Removal Assessment

    Science.gov (United States)

    2015-01-01

    etc. have on coke deposition from RP-1 and RP-2 as well as showing that we can oxidize and remove these deposits using ozone , would be very...Meeting; 29 Apr. - 3 May, Colorado Springs, CO. 10Billingsley, M.C. H.Y. Lyu and R.W. Bates (2007). "Experimental and Numerical Investigations of RP...5th Modeling and Simulation Subcommittee Joint Meeting, Denver, CO, 14-17 May. 11Linne, D.L., M. L. Meyer, T. Edwards, and D. A. Eitman (1997

  4. Coumarin-modified microporous-mesoporous Zn-MOF-74 showing ultra-high uptake capacity and photo-switched storage/release of U(VI) ions.

    Science.gov (United States)

    Zhang, Le; Wang, Lin Lin; Gong, Le Le; Feng, Xue Feng; Luo, Ming Biao; Luo, Feng

    2016-07-05

    Driven by an energy crisis but consequently puzzled by various environmental problems, uranium, as the basic material of nuclear energy, is now receiving extensive attentions. In contrast to numerous sorbents applied in this field, metal-organic framework (MOFs), as a renovated material platform, has only recently been developed. How to improve the adsorption capacity of MOF materials towards U(VI) ions, as well as taking advantage of the nature of these MOFs to design photo-switched behaviour for photo-triggered storage/release of U(VI) ions are at present urgent problems and great challenges to be solved. Herein, we show a simple and facile method to target the goal. Through coordination-based post-synthetic strategy, microporous- mesoporous Zn-MOF-74 was easily functionalized by grafting coumarin on coordinatively unsaturated Zn(II) centers, yielding a series of coumarin-modified Zn-MOF-74 materials. The obtained samples displayed ultra-high adsorption capacity for U(VI) ions from water at pH value of 4 with maximum adsorption capacities as high as 360 mg/g (the record value in MOFs) and a remarkable photo-switched capability of 50 mg/g at pH value of 4. To the best of knowledge, and in contrast to the well-known photo-switched behaviour towards CO2, dye (propidium iodide), as well as fluorescence observed in MOFs, this is the first study that shows a photo-switched behaviour towards radioactive U(VI) ions in aqueous solution.

  5. Effects of the aspartic protease inhibitor from Lupinus bogotensis seeds on the growth and development of Hypothenemus hampei: an inhibitor showing high homology with storage proteins.

    Science.gov (United States)

    Molina, Diana; Patiño, Luisa; Quintero, Mónica; Cortes, José; Bastos, Sara

    2014-02-01

    The coffee berry borer Hypothenemus hampei is a pest that causes great economic damage to coffee grains worldwide. Because the proteins consumed are digested by aspartic proteases in the insect's midgut, the inhibition of these proteases by transferring a gene encoding an aspartic protease inhibitor from Lupinus bogotensis Benth. to coffee plants could provide a promising strategy to control this pest. Five aspartic protease inhibitors from L. bogotensis (LbAPI) were accordingly purified and characterized. The gene encoding the L. bogotensis aspartic protease inhibitor (LbAPI), with the highest inhibitory activity against H. hampei, was expressed in Escherichia coli and the purified recombinant protein (rLbAPI), with a molecular mass of 15 kDa, was subsequently assessed for its ability to inhibit the aspartic protease activity present in the H. hampei midgut in vitro, as well as its effects on the growth and development of H. hampei in vivo. The in vitro experiments showed that rLbAPI was highly effective against aspartic proteases from H. hampei guts, with a half maximal inhibitory concentration (IC50) of 2.9 μg. The in vivo experiments showed that the concentration of rLbAPI (w/w) in the artificial diet necessary to cause 50% mortality (LD50) of the larvae was 0.91%. The amino acid sequence of LbAPI had high homology (52-80%) to the seed storage proteins, vicilin and β-conglutin, suggesting that this protein was generated by evolutionary events from a β-conglutin precursor. Based on these results, LbAPI may have a dual function as storage protein, and as defense protein against H. hampei. These results provide a promising alternative to obtain a coffee plant resistant to H. hampei. Copyright © 2013 Elsevier Ltd. All rights reserved.

  6. Plasma relaxation mechanics of pulsed high power microwave surface flashover

    Energy Technology Data Exchange (ETDEWEB)

    Beeson, S.; Dickens, J.; Neuber, A. [Center for Pulsed Power and Power Electronics, Department of Electrical and Computer Engineering and Department of Physics, Texas Tech University, Lubbock, Texas 79409 (United States)

    2013-09-15

    Microwave transmission and reflection characteristics of pulsed radio frequency field generated plasmas are elucidated for air, N{sub 2}, and He environments under pressure conditions ranging from 10 to 600 torr. The pulsed, low temperature plasma is generated along the atmospheric side of the dielectric boundary between the source (under vacuum) and the radiating environment with a thickness on the order of 5 mm and a cross sectional area just smaller than that of the waveguide. Utilizing custom multi-standard waveguide couplers and a continuous low power probing source, the scattering parameters were measured before, during, and after the high power microwave pulse with emphasis on the latter. From these scattering parameters, temporal electron density estimations (specifically the longitudinal integral of the density) were calculated using a 1D plane wave-excited model for analysis of the relaxation processes associated. These relaxation characteristics ultimately determine the maximum repetition rate for many pulsed electric field applications and thus are applicable to a much larger scope in the plasma community than just those related to high power microwaves. This manuscript discusses the diagnostic setup for acquiring the power measurements along with a detailed description of the kinematic and chemical behavior of the plasma as it decays down to its undisturbed state under various gas type and pressure conditions.

  7. Second-surface silvered glass solar mirrors of very high reflectance

    Science.gov (United States)

    Butel, Guillaume P.; Coughenour, Blake M.; Macleod, H. Angus; Kennedy, Cheryl E.; Olbert, Blain H.; Angel, J. Roger P.

    2011-10-01

    This paper reports methods developed to maximize the overall reflectance second-surface silvered glass. The reflectance at shorter wavelengths is increased with the aid of a dielectric enhancing layer between the silver and the glass, while at longer wavelengths it is enhanced by use of glass with negligible iron content. The calculated enhancement of reflectance, compared to unenhanced silver on standard low-iron float glass, corresponds to a 4.4% increase in reflectance averaged across the full solar spectrum, appropriate for CSP, and 2.7% for CPV systems using triple junction cells. An experimental reflector incorporating these improvements, of drawn crown glass and a silvered second-surface with dielectric boost, was measured at NREL to have 95.4% solar weighted reflectance. For comparison, non-enhanced, wetsilvered reflectors of the same 4 mm thickness show reflectance ranging from 91.6 - 94.6%, depending on iron content. A potential drawback of using iron-free drawn glass is reduced concentration in high concentration systems because of the inherent surface errors. This effect is largely mitigated for glass shaped by slumping into a concave mold, rather than by bending.

  8. High Reynolds number rough wall turbulent boundary layer experiments using Braille surfaces

    Science.gov (United States)

    Harris, Michael; Monty, Jason; Nova, Todd; Allen, James; Chong, Min

    2007-11-01

    This paper details smooth, transitional and fully rough turbulent boundary layer experiments in the New Mexico State high Reynolds number rough wall wind tunnel. The initial surface tested was generated with a Braille printer and consisted of an uniform array of Braille points. The average point height being 0.5mm, the spacing between the points in the span was 0.5mm and the surface consisted of span wise rows separated by 4mm. The wavelength to peak ratio was 8:1. The boundary layer thickness at the measurement location was 190mm giving a large separation of roughness height to layer thickness. The maximum friction velocity was uτ=1.5m/s at Rex=3.8 x10^7. Results for the skin friction co-efficient show that this surface follows a Nikuradse type inflectional curve and that Townsends outer layer similarity hypothesis is valid for rough wall flows with a large separation of scales. Mean flow and turbulence statistics will be presented.

  9. Highly controllable near-surface swimming of magnetic Janus nanorods: application to payload capture and manipulation

    Energy Technology Data Exchange (ETDEWEB)

    Mair, Lamar O; Carpenter, Jerome [Curriculum in Applied Sciences and Engineering, University of North Carolina at Chapel Hill, NC 27599 (United States); Evans, Benjamin [Department of Physics, Elon University, Elon, NC 27244 (United States); Hall, Adam R [Joint School of Nanoscience and Nanoengineering, University of North Carolina at Greensboro, NC 27401 (United States); Shields, Adam; Superfine, Richard [Department of Physics and Astronomy, University of North Carolina at Chapel Hill, NC 27599 (United States); Ford, Kris; Millard, Michael, E-mail: rsuper@physics.unc.edu [Department of Biomedical Engineering, University of North Carolina at Chapel Hill, NC 27599 (United States)

    2011-03-30

    Directed manipulation of nanomaterials has significant implications in the field of nanorobotics, nanobiotechnology, microfluidics and directed assembly. With the goal of highly controllable nanomaterial manipulation in mind, we present a technique for the near-surface manoeuvering of magnetic nanorod swimmers and its application to controlled micromanipulation. We fabricate magnetic Janus nanorods and show that the magnetic rotation of these nanorods near a floor results in predictable translational motion. The nanorod plane of rotation is nearly parallel to the floor, the angle between rod tilt and floor being expressed by {theta}, where 0{sup 0} < {theta} < 20{sup 0}. Orthogonal magnetic fields control in-plane motion arbitrarily. Our model for translation incorporates symmetry breaking through increased drag at the no-slip surface boundary. Using this method we demonstrate considerable rod steerability. Additionally, we approach, capture, and manipulate a polystyrene microbead as proof of principle. We attach Janus nanorods to the surfaces of cells and utilize these rods to manipulate individual cells, proving the ability to manoeuver payloads with a wide range of sizes.

  10. Highly stable hydrophilic surfaces of PDMS thin layer obtained by UV radiation and oxygen plasma treatments

    Energy Technology Data Exchange (ETDEWEB)

    Menezes Atayde, Cleuson de; Doi, Ioshiaki [Center for Semiconductor Components, University of Campinas - UNICAMP, Campinas, SP (Brazil); School of Electrical and Computer Engineering, University of Campinas - UNICAMP, Campinas, SP (Brazil)

    2010-02-15

    Surface modification of polydimethylsiloxane (PDMS, Sylgard 184) was carried out by O{sub 2} plasma and UV in broadband mode/O{sub 2} plasma treatments with different exposure times, and studied in terms of hydrophilic stability. Water contact angle measurements, Fourier Transform infrared spectroscopy (FTIR) and atomic force microscopy (AFM) were used for the analysis of the modified surface and hydrophilic stability of the PDMS films. The results show reasonably good hydrophilic stability in the range of a week with a contact angle of around 70 for O{sub 2} plasma treated samples, whereas a more high hydrophilic stability, with a low contact angle of 65 up to 15 days, was observed for UV/O{sub 2} plasma treated PDMS. FTIR analysis of the samples reveals significant oxidation noted by large presence of Si-O-Si, and Si-OH bonds on the PDMS surface, which improves the affinity with water molecules and increases the hydrophilicy. (copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  11. Condensation on Highly Superheated Surfaces: Unstable Thin Films in a Wickless Heat Pipe.

    Science.gov (United States)

    Kundan, Akshay; Nguyen, Thao T T; Plawsky, Joel L; Wayner, Peter C; Chao, David F; Sicker, Ronald J

    2017-03-03

    A wickless heat pipe was operated on the International Space Station to provide a better understanding of how the microgravity environment might alter the physical and interfacial forces driving evaporation and condensation. Traditional heat pipes are divided into three zones: evaporation at the heated end, condensation at the cooled end, and intermediate or adiabatic in between. The microgravity experiments reported herein show that the situation may be dramatically more complicated. Beyond a threshold heat input, there was a transition from evaporation at the heated end to large-scale condensation, even as surface temperatures exceeded the boiling point by 160 K. The hotter the surface, the more vapor was condensed onto it. The condensation process at the heated end is initiated by thickness and temperature disturbances in the thin liquid film that wet the solid surface. Those disturbances effectively leave the vapor "superheated" in that region. Condensation is amplified and sustained by the high Marangoni stresses that exist near the heater and that drive liquid to cooler regions of the device.

  12. Two ras genes in Dictyostelium minutum show high sequence homology, but different developmental regulation from Dictyostelium discoideum rasD and rasG genes.

    Science.gov (United States)

    van Es, S; Kooistra, R A; Schaap, P

    1997-03-10

    The social amoeba Dictyostelium discoideum expresses five ras genes at different stages of development. One of them, DdrasD is expressed during postaggregative development and transcription is induced by extracellular cAMP. A homologue of DdrasD, the DdrasG gene, is expressed exclusively during vegetative growth. We cloned two ras homologues Dmras1 and Dmras2 from the primitive species D. minutum, which show high homology to DdrasD and DdrasG and less homology to the other Ddras genes. In contrast to the DdrasD and DdrasG genes, both the Dmras1 and Dmras2 genes are expressed during the entire course of development. The expression levels are low during growth, increase at the onset of starvation and do not decrease until fruiting bodies have formed. Expression of neither Dmras1 or Dmras2 is regulated by cAMP. So even though the high degree of homology between the ras genes of different species suggests conservation of function, this function is apparently not associated with a specific developmental stage.

  13. Male rats with same sex preference show high experimental anxiety and lack of anxiogenic-like effect of fluoxetine in the plus maze test.

    Science.gov (United States)

    García-Cárdenas, Nallely; Olvera-Hernández, Sandra; Gómez-Quintanar, Blanca Nelly; Fernández-Guasti, Alonso

    2015-08-01

    Homosexual men show a 2-4 higher risk to suffer anxiety in comparison with heterosexuals. It is unknown if biological factors collaborate to increase such incidence. Fluoxetine produces differential brain activation in homosexuals as compared with heterosexuals, suggesting that it may produce a divergent behavioral effect dependant on sex-preference. The first aim was to evaluate experimental anxiety in male rats that show same-sex preference in the elevated plus maze (EPM). The second goal explored the putative differential effect of fluoxetine (10mg/kg) in male rats with female and same-sex preference in the EPM. To induce same-sex preference males were prenatally treated with letrozole (0.56μg/kg, 10-20 gestation days), while controls were males prenatally treated with letrozole that retain female-preference or which mothers received oil. In both groups we found animals with male preference, but the proportion was higher in males that prenatally received letrozole (10 vs. 27%). Males with same-sex preference spent less time and showed lower number of entries to the open arms of the EPM than males that prefer females, regardless of the prenatal treatment. In males with female preference, fluoxetine reduced the time spent and number of entries to the open arms that was absent in males with same-sex preference. These data suggest that biological factors contribute to the high levels of anxiety in subjects with same-sex preference and that fluoxetine in men may produce a divergent action depending on sexual orientation.

  14. Enhancing Plasma Surface Modification using high Intensity and high Power Ultrasonic Acoustic Waves

    DEFF Research Database (Denmark)

    2010-01-01

    This invention relates to a plasma surface modification process (and a corresponding a system) of a solid object (100) comprising creating plasma (104) by a plasma source (106), application of the plasma (104) to at least a part of a surface (314) of the solid object (100), generating ultrasonic...... or a mixture of gases (500) flow in contact with said solid object (100) is thinned or destructed for at least a part of said surface (314). In this way, the plasma can more efficiently access and influence the surface of the solid object to be treated by the plasma, which speeds the process time up...

  15. A highly stable nonbiofouling surface with well-packed grafted zwitterionic polysulfobetaine for plasma protein repulsion.

    Science.gov (United States)

    Chang, Yung; Liao, Shih-Chieh; Higuchi, Akon; Ruaan, Ruoh-Chyu; Chu, Chih-Wei; Chen, Wen-Yih

    2008-05-20

    An ideal nonbiofouling surface for biomedical applications requires both high-efficient antifouling characteristics in relation to biological components and long-term material stability from biological systems. In this study we demonstrate the performance and stability of an antifouling surface with grafted zwitterionic sulfobetaine methacrylate (SBMA). The SBMA was grafted from a bromide-covered gold surface via surface-initiated atom transfer radical polymerization to form well-packed polymer brushes. Plasma protein adsorption on poly(sulfobetaine methacrylate) (polySBMA) grafted surfaces was measured with a surface plasmon resonance sensor. It is revealed that an excellent stable nonbiofouling surface with grafted polySBMA can be performed with a cycling test of the adsorption of three model proteins in a wide range of various salt types, buffer compositions, solution pH levels, and temperatures. This work also demonstrates the adsorption of plasma proteins and the adhesion of platelets from human blood plasma on the polySBMA grafted surface. It was found that the polySBMA grafted surface effectively reduces the plasma protein adsorption from platelet-poor plasma solution to a level superior to that of adsorption on a surface terminated with tetra(ethylene glycol). The adhesion and activation of platelets from platelet-rich plasma solution were not observed on the polySBMA grafted surface. This work further concludes that a surface with good hemocompatibility can be achieved by the well-packed surface-grafted polySBMA brushes.

  16. Surface plasmon resonance biosensor with high anti-fouling ability for the detection of cardiac marker troponin T.

    Science.gov (United States)

    Liu, Jen Tsai; Chen, Ching Jung; Ikoma, Toshiyuki; Yoshioka, Tomohiko; Cross, Jeffrey S; Chang, Shwu-Jen; Tsai, Jang-Zern; Tanaka, Junzo

    2011-10-03

    Designing a surface recognition layer with high anti-fouling ability, high affinity, and high specificity is an important issue to produce high sensitivity biosensing transducers. In this study, a self-assembled monolayer (SAM) consisting of a homogeneous mixture of oligo(ethylene glycol) (OEG)-terminated alkanethiolate and mercaptohexadecanoic acid (MHDA) on Au was employed for immobilizing troponin T antibody and applied in detecting cardiac troponin T by using surface plasmon resonance (SPR). The mixed SAM showed no phase segregation and exhibited human serum albumin resistance, particularly with an antibody-immobilized surface. X-ray photoemission spectra revealed that the chemical composition ratio of OEG to the mixed SAM was 69% and the OEG packing density was 82%. The specific binding of troponin T on the designed surface indicated a good linear correlation (R=0.991, P<0.0009) at concentrations lower than 50 μgmL(-1) with the limit of detection of 100 ngmL(-1) using a SPR measuring instrument. It is concluded that the mixed SAM functions as designed since it has high detection capability, high accuracy and reproducibility, as well as shows strong potential to be applied in rapid clinical diagnosis for label-free detection within 2 min.

  17. Characterization of highly anisotropic three-dimensionally nanostructured surfaces

    CERN Document Server

    Schmidt, Daniel

    2013-01-01

    Generalized ellipsometry, a non-destructive optical characterization technique, is employed to determine geometrical structure parameters and anisotropic dielectric properties of highly spatially coherent three-dimensionally nanostructured thin films grown by glancing angle deposition. The (piecewise) homogeneous biaxial layer model approach is discussed, which can be universally applied to model the optical response of sculptured thin films with different geometries and from diverse materials, and structural parameters as well as effective optical properties of the nanostructured thin films are obtained. Alternative model approaches for slanted columnar thin films, anisotropic effective medium approximations based on the Bruggeman formalism, are presented, which deliver results comparable to the homogeneous biaxial layer approach and in addition provide film constituent volume fraction parameters as well as depolarization or shape factors. Advantages of these ellipsometry models are discussed on the example ...

  18. Mapping of Impervious Surfaces and Green Vegetation Fraction in Urban Areas Using High-Resolution Optical- and SAR- Data

    Science.gov (United States)

    Mack, Benjamin; Becker, Frauke; Menz, Gunther

    2010-12-01

    Impervious surfaces (IS) and vegetated surfaces (VS) are two important variables for urban planning. Both are related to surface biophysical processes (e. g. urban heat island) and the quality of life in urban environments. The new generation of spatially very high resolution satellite sensors (e.g. RapidEye, or TerraSAR-X) show promising capabilities to extract these variables in relevant detail and hence to overcome some of the limitations using traditional approaches. In this study, we show a simple workflow for the synergistic use of high-resolution optical and SAR data for the retrieval of detailed information of IS and VS. Here, the focus is on the processing step of vegetation extraction. Three approaches - linear Spectral Mixture Analysis, per-pixel, and segment-oriented classification - are compared. It will also be analyzed if an explicit shadow analysis leads to a significant improvement of the products.

  19. Formation of recent martian debris flows by melting of near-surface ground ice at high obliquity.

    Science.gov (United States)

    Costard, F; Forget, F; Mangold, N; Peulvast, J P

    2002-01-04

    The observation of small gullies associated with recent surface runoff on Mars has renewed the question of liquid water stability at the surface of Mars. The gullies could be formed by groundwater seepage from underground aquifers; however, observations of gullies originating from isolated peaks and dune crests question this scenario. We show that these landforms may result from the melting of water ice in the top few meters of the martian subsurface at high obliquity. Our conclusions are based on the analogy between the martian gullies and terrestrial debris flows observed in Greenland and numerical simulations that show that above-freezing temperatures can occur at high obliquities in the near surface of Mars, and that such temperatures are only predicted at latitudes and for slope orientations corresponding to where the gullies have been observed on Mars.

  20. Formation of Recent Martian Debris Flows by Melting of Near-Surface Ground Ice at High Obliquity

    Science.gov (United States)

    Costard, F.; Forget, F.; Mangold, N.; Peulvast, J. P.

    2002-01-01

    The observation of small gullies associated with recent surface runoff on Mars has renewed the question of liquid water stability at the surface of Mars. The gullies could be formed by groundwater seepage from underground aquifers; however, observations of gullies originating from isolated peaks and dune crests question this scenario. We show that these landforms may result from the melting of water ice in the top few meters of the martian subsurface at high obliquity. Our conclusions are based on the analogy between the martian gullies and terrestrial debris flows observed in Greenland and numerical simulations that show that above-freezing temperatures can occur at high obliquities in the near surface of Mars, and that such temperatures are only predicted at latitudes and for slope orientations corresponding to where the gullies have been observed on Mars.

  1. Effect of surface catalycity on high-altitude aerothermodynamics of reentry vehicles

    Science.gov (United States)

    Molchanova, A. N.; Kashkovsky, A. V.; Bondar, Ye. A.

    2016-10-01

    This work is aimed at the development of surface chemistry models for the Direct Simulation Monte Carlo (DSMC) method applicable to non-equilibrium high-temperature flows about reentry vehicles. Probabilities of the surface processes dependent on individual properties of each particular molecule are determined from the macroscopic reaction rate data. Two different macroscopic finite rate sets are used for construction of DSMC surface recombination models. The models are implemented in the SMILE++ software system for DSMC computations. A comparison with available experimental data is performed. Effects of surface recombination on the aerothermodynamics of a blunt body at high-altitude reentry conditions are numerically studied with the DSMC method.

  2. Development and Characterization of Diamond Film and Compound Metal Surface High Current Photocathodes

    Science.gov (United States)

    Shurter, R. P.; Moir, D. C.; Shurter, R. P.; Moir, D. C.

    1997-05-01

    High current photocathodes operating in vacuum environments as high as 10-5 torr are being developed at Los Alamos for use in a new generation of linear induction accelerators. We report high quantum efficiencies and high current densities in wide bandgap semiconductor and compound metal surface thermally augmented photocathode materials illuminated by ultraviolet laser radiation.

  3. Cell surface profiling using high-throughput flow cytometry: a platform for biomarker discovery and analysis of cellular heterogeneity.

    Directory of Open Access Journals (Sweden)

    Craig A Gedye

    Full Text Available Cell surface proteins have a wide range of biological functions, and are often used as lineage-specific markers. Antibodies that recognize cell surface antigens are widely used as research tools, diagnostic markers, and even therapeutic agents. The ability to obtain broad cell surface protein profiles would thus be of great value in a wide range of fields. There are however currently few available methods for high-throughput analysis of large numbers of cell surface proteins. We describe here a high-throughput flow cytometry (HT-FC platform for rapid analysis of 363 cell surface antigens. Here we demonstrate that HT-FC provides reproducible results, and use the platform to identify cell surface antigens that are influenced by common cell preparation methods. We show that multiple populations within complex samples such as primary tumors can be simultaneously analyzed by co-staining of cells with lineage-specific antibodies, allowing unprecedented depth of analysis of heterogeneous cell populations. Furthermore, standard informatics methods can be used to visualize, cluster and downsample HT-FC data to reveal novel signatures and biomarkers. We show that the cell surface profile provides sufficient molecular information to classify samples from different cancers and tissue types into biologically relevant clusters using unsupervised hierarchical clustering. Finally, we describe the identification of a candidate lineage marker and its subsequent validation. In summary, HT-FC combines the advantages of a high-throughput screen with a detection method that is sensitive, quantitative, highly reproducible, and allows in-depth analysis of heterogeneous samples. The use of commercially available antibodies means that high quality reagents are immediately available for follow-up studies. HT-FC has a wide range of applications, including biomarker discovery, molecular classification of cancers, or identification of novel lineage specific or stem cell

  4. Study of high cycle fatigue of PVD surface-modified austempered ductile iron

    Energy Technology Data Exchange (ETDEWEB)

    Feng, H.P.; Lee, S.C.; Hsu, C.H.; Ho, J.M. [Tatung Inst. of Technol., Taipei (Taiwan, Province of China). Dept. of Mater. Eng.

    1999-05-25

    Austempered ductile iron (ADI) is made from ductile iron by an austempering treatment, and its main microstructure is ausferrite that is composed of acicular ferrite and high carbon austenite. The purpose of this e