WorldWideScience

Sample records for surface roughness testing

  1. Rough surface

    International Nuclear Information System (INIS)

    Hudina, M.

    1982-08-01

    For the determination of the thermal-hydraulic performances of rough surfaces, the method of evaluation is particularly important. In order to increase confidence in the results, a new evaluation procedure was introduced. This procedure is based on the transformation of simple channel experimental results to equal boundary conditions, and on the suitable application and confirmation of these transformed values in more complicated flow channel geometries. Existing methods, applied to the results obtained in an annular channel, do not fulfil all the transformation requirements. Thus a new, more complete transformation method, which uses the turbulent eddy diffusivity model, was developed. To check the quality of this transformation, within the scope of the new evaluation procedure, the results of experimental investigation in annular channels and in a bundle of hexagonal geometry were used together with the predictions of benchmark calculations. The success of the new method was confirmed by extensive comparisons, with the results of different presently-acknowledged transformations being considered as well. Based on these comparisons an assessment of the individual transformations is given. (Auth.)

  2. Skid resistance and surface roughness testing of historic stone surfaces: advantages and limitations

    Science.gov (United States)

    Török, Ákos

    2013-04-01

    Skid resistance tests are mostly applied for testing road surfaces and almost never applied for testing stones at cultural heritage sites. The present study focuses on the possibilities of using these techniques in assessing the surface roughness of paving stones at a historic site. Two different methods were used in a comparative way to evaluate the surface properties of various types of stones ranging from travertine to non-porous limestone and granite. The applied techniques included the use of SRT pendulum (Skid Resistance Tester) providing USRV values and a mobile equipment to analyze the surface properties (Floor Slide Control) by surface profiling and providing angle of friction. The main aims of tests were to understand the wearing of stone materials due to intense pedestrian use and to detect surface changes/surface roughness and slip resistance within few year periods. The measured loss in surface slip resistance (i.e. USRV values) was in the order of 20% for granites, while most limestones lost at least 40% in terms of USRV values. An opposite trend was detected for a porous travertine type, where the surface became rougher after years of use. The limitations of these techniques are also addressed in the paper. The tests have shown that the introduction of the use of these equipments in heritage studies provide useful information on the longevity of historic stone pavements that are open for public use.

  3. Topographical evaluation of different glass and quartz fiber post surface treatments by a tridimensional surface roughness test.

    Science.gov (United States)

    Soares, Leandro Passos; Dias, Katia Regina Hostilio Cervantes; de Vasconcellos, Adalberto Bastos; Sampaio, Eduardo Martins; Limaverde, Aricelso Maia; Barceleiro, Marcos de Oliveira

    2010-01-01

    A tridimensional surface roughness test evaluation is a nondestructive method that can be used to perform a topographic analysis of different surface treatments for glass and quartz fiber posts. This study divided 75 fiber posts into three groups according to their manufacturer. Each group was divided into five subgroups (n = 5), according to the surface treatment each received: immersion in hydrofluoric acid, sandblasting, immersion in hydrogen peroxide, sandblasting followed by immersion in hydrofluoric acid, or sandblasting followed by immersion in hydrogen peroxide. Surface roughness was measured using a tridimensional surface roughness test and analyzed with three-dimensional analysis software. Results were statistically analyzed using Student's t-test. The only surface treatment to modify the surface topography of glass and quartz fiber posts and provide a significant increase in roughness was sandblasting airborne-particle abrasion with 50 micro alumina at a distance of 30 mm, using 2.5 bars of pressure for five seconds.

  4. Effects of surface roughness on magnetic flux leakage testing of micro-cracks

    Science.gov (United States)

    Deng, Zhiyang; Sun, Yanhua; Yang, Yun; Kang, Yihua

    2017-04-01

    Magnetic flux leakage (MFL) testing owns the advantages of high inspection sensitivity and stability, but its testing results are always affected by surface roughness. The relationship between the surface roughness ({{R}a} ) and detection signals for surface-breaking cracks is mainly discussed. The existence of roughness magnetic compression effect (RMCE) in present MFL testing is specially pointed out and its relevant theory is also analyzed, which manifest themselves in the compression of MFL signal in its peak value and the baseline drifts mixed with noise. An experimental investigation on surface comparators with different arithmetic average height ({{R}a} ) and artificial notch size, is performed to analyze the effects of surface roughness on detection signals of cracks. The detection limit (DL) of micro-crack is analyzed by comparing the {{B}y} noise-signal ratio ({{S}y} ) and peak-peak signals of the cracks. Meanwhile, {{S}y} increases with the {{R}a} and R{{S}m} , in this case, relatively shallow defects cannot be clearly distinguished at determined rough surface. Afterwards, a series of simulations are designed and performed to verify the effects of surface roughness on characteristic {{B}y} of the electromagnetic field, and a theoretical DL of micro-crack is presented as: DL=2.88{{R}a}+7.00 . Furthermore, the optimal lift-off value is selected for the micro-cracks’ detection to weaken the negative magnetic compression effect. MFL signals cannot reflect the accurate sizes of the cracks on rough surface due to the RMCE and its relevant phenomenon. The discovery and results will benefit the quantitative evaluation of the MFL testing.

  5. Test Operation Procedure (TOP) 01-1-010A Vehicle Test Course Severity (Surface Roughness)

    Science.gov (United States)

    2017-12-12

    natural terrain by the addition of course material (known locally as tosca) to improve traction, and by the addition of several logs buried in...sections of the course that must be traversed; the logs are buried approximately to the midpoint of their diameters, range from approximately half a foot...of Establishment of Quality Control Charts for Test Course Inspection Roughness, TECOM Project No. 9-CO-011-000-055, John P. Sobczyk, July 1972. c

  6. Deposition of Aerosol Particles on Rough Surfaces Inside a Test Chamber

    Czech Academy of Sciences Publication Activity Database

    Hussein, T.; Kubincová, L.; Ondráčková, Lucie; Hruška, A.; Dohányosová, Pavla; Hemerka, J.; Smolík, Jiří

    2009-01-01

    Roč. 44, č. 10 (2009), s. 2056-2063 ISSN 0360-1323 R&D Projects: GA ČR GA101/04/1190; GA ČR GA101/07/1361 Institutional research plan: CEZ:AV0Z40720504 Keywords : deposition rate * hydraulically smooth * surface roughness Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 1.797, year: 2009

  7. Armor Plate Surface Roughness Measurements

    National Research Council Canada - National Science Library

    Stanton, Brian; Coburn, William; Pizzillo, Thomas J

    2005-01-01

    ...., surface texture and coatings) that could become important at high frequency. We measure waviness and roughness of various plates to know the parameter range for smooth aluminum and rolled homogenous armor (RHA...

  8. Surface roughness from highlight structure

    NARCIS (Netherlands)

    Lu, Rong; Koenderink, Jan J.; Kappers, Astrid M L

    1999-01-01

    Highlights are due to specular reflection and cause the lustrous or mirrorlike appearance of many material surfaces. We investigated in detail the structure of highlight patterns that are due to material surface roughness. We interpret results in terms of a simple model of a random Gaussian surface.

  9. Heat transfer from rough surfaces

    International Nuclear Information System (INIS)

    Dalle Donne, M.

    1980-11-01

    The transformation of the friction data obtained with experiments in annuli can be performed either with the assumption of universal logarithmic velocity profile or of an universal eddy momentum diffusivity profile. For the roughness of practical interest both methods, when properly applied, give good results. For these roughnesses the transformed friction factors seem not to be unduly affected if one assumes a constant slope of the velocity profile equal to 2.5. All the transformation methods of the heat transfer data so far proposed predict too high wall temperatures in the central channels of a 19-rod bundle with three-dimensional roughness. Preliminary calculations show that the application of the superimposition principle with the logarithmic temperature profiles gives good results for the three-dimensional roughness as well. Although the measurements show that the slope of the logarithmic temperature profiles is different from 2.5, the assumption of a constant slope equal to 2.5 does not affect the transformed heat transfer data appreciably. For moderately high roughness ribs the turbulent Prandtl number, averaged over the cross section of a tube, is about the same (approx. 0.8) for rough as for smooth surfaces. The temperature effect on the heat transfer data with air cooling is stronger than originally assumed in the general correlation of Dalle Donne and Meyer. With helium cooling this temperature effect is even stronger. (orig.) [de

  10. Simplified Approach to Predicting Rough Surface Transition

    Science.gov (United States)

    Boyle, Robert J.; Stripf, Matthias

    2009-01-01

    Turbine vane heat transfer predictions are given for smooth and rough vanes where the experimental data show transition moving forward on the vane as the surface roughness physical height increases. Consiste nt with smooth vane heat transfer, the transition moves forward for a fixed roughness height as the Reynolds number increases. Comparison s are presented with published experimental data. Some of the data ar e for a regular roughness geometry with a range of roughness heights, Reynolds numbers, and inlet turbulence intensities. The approach ta ken in this analysis is to treat the roughness in a statistical sense , consistent with what would be obtained from blades measured after e xposure to actual engine environments. An approach is given to determ ine the equivalent sand grain roughness from the statistics of the re gular geometry. This approach is guided by the experimental data. A roughness transition criterion is developed, and comparisons are made with experimental data over the entire range of experimental test co nditions. Additional comparisons are made with experimental heat tran sfer data, where the roughness geometries are both regular as well a s statistical. Using the developed analysis, heat transfer calculatio ns are presented for the second stage vane of a high pressure turbine at hypothetical engine conditions.

  11. ROUGHNESS ON WOOD SURFACES AND ROUGHNESS MEASUREMENT METHODS

    Directory of Open Access Journals (Sweden)

    İsmail Aydın

    2003-04-01

    Full Text Available Some visual characteristics of wood such as color, pattern and texture determine the quality of manufactured products. Surface properties of wood material are important both in production and marketing after production. Initial studies related to the roughness of wood surface were begun in early 1950’s. However, no general agreed standardization can not have been developed for wood surfaces. Surface roughness of wood is function of the production process, product type and the natural anatomical properties of wood. Contact and non-contact tracing methods are used to measure of wood surface roughness. Surface roughness also affects the gluability and wettability of wood surfaces. The success in finishing also depends on the surface roughness of wood.

  12. Heat transfer from rough surfaces

    International Nuclear Information System (INIS)

    Dalle Donne, M.

    1977-01-01

    Artificial roughness is often used in nuclear reactors to improve the thermal performance of the fuel elements. Although these are made up of clusters of rods, the experiments to measure the heat transfer and friction coefficients of roughness are performed with single rods contained in smooth tubes. This work illustrated a new transformation method to obtain data applicable to reactor fuel elements from these annulus experiments. New experimental friction data are presented for ten rods, each with a different artificial roughness made up of two-dimensional rectangular ribs. For each rod four tests have been performed, each in a different outer smooth tube. For two of these rods, each for two different outer tubes, heat transfer data are also given. The friction and heat transfer data, transformed with the present method, are correlated by simple equations. In the paper, these equations are applied to a case typical for a Gas Cooled Fast Reactor fuel element. (orig.) [de

  13. ROUGHNESS ON WOOD SURFACES AND ROUGHNESS MEASUREMENT METHODS

    OpenAIRE

    İsmail Aydın; Gürsel Çolakoğlu

    2003-01-01

    Some visual characteristics of wood such as color, pattern and texture determine the quality of manufactured products. Surface properties of wood material are important both in production and marketing after production. Initial studies related to the roughness of wood surface were begun in early 1950’s. However, no general agreed standardization can not have been developed for wood surfaces. Surface roughness of wood is function of the production process, product type and the natural anatomic...

  14. Reproducibility of surface roughness in reaming

    DEFF Research Database (Denmark)

    Müller, Pavel; De Chiffre, Leonardo

    An investigation on the reproducibility of surface roughness in reaming was performed to document the applicability of this approach for testing cutting fluids. Austenitic stainless steel was used as a workpiece material and HSS reamers as cutting tools. Reproducibility of the results was evaluat...

  15. EFFECT OF SURFACE TREATMENT ON ENAMEL SURFACE ROUGHNESS

    Directory of Open Access Journals (Sweden)

    Şeyda Erşahan

    2016-01-01

    Full Text Available Purpose: To compare the effects of different methods of surface treatment on enamel roughness. Materials and Methods: Ninety human maxillary first premolars were randomly divided into three groups (n=30 according to type of enamel surface treatment: I, acid etching; II, Er:YAG laser; III, Nd:YAG laser. The surface roughness of enamel was measured with a noncontact optical profilometer. For each enamel sample, two readings were taken across the sample—before enamel surface treatment (T1 and after enamel surface treatment (T2. The roughness parameter analyzed was the average roughness (Ra. Statistical analysis was performed using a Paired sample t test and the post-hoc Mann- Whitney U test, with the significance level set at 0.05. Results: The highest Ra (average roughness values were observed for Group II, with a significant difference with Groups I and III (P<0.001. Ra values for the acid etching group (Group I were significantly lower than other groups (P<0.001. Conclusion: Surface treatment of enamel with Er:YAG laser and Nd:YAG laser results in significantly higher Ra than acid-etching. Both Er:YAG laser or Nd:YAG laser can be recommended as viable treatment alternatives to acid etching.

  16. Evaluation of pH Levels and Surface Roughness After Bleaching and Abrasion Tests of Eight Commercial Products.

    Science.gov (United States)

    Trentino, Ana Carolina; Soares, Ana Flavia; Duarte, Marco Antonio Hungaro; Ishikiriama, Sérgio Kiyoshi; Mondelli, Rafael Francisco Lia

    2015-07-01

    This in vitro study evaluated the effect of different bleaching protocols and the variation of pH levels of bleaching gels regarding roughness and wear of bovine enamel, after in-office bleaching protocols and brushing. Ninety fragments were randomly divided into nine groups: C, control; WHP15, 35% hydrogen peroxide (HP) (Whiteness HP, FGM) three gel applications of 15 min each, three sessions with 1 week intervals; WHP45, 35% HP (Whiteness HP) one application/45 min, three sessions with 1 week intervals; LPS, 35% HP (Lase Peroxide, DMC) plus hybrid light (HL) [light-emitting diode (LED)/diode laser], four applications/7 min 30 sec (6 min of HL activation), one session; LPSII, 25% HP (Lase Peroxide II, DMC) plus HL, four applications/7 min 30 sec (6 min of HL activation), one session; LPL, 15% HP (Lase Peroxide Light, DMC) four applications/7 min 30 sec (6 min of HL activation), one session; WO, 35% HP (Whitegold Office, Dentsply) three applications/15 min, three sessions with 1 week intervals; WBC40, 35% HP (Whiteness HP Blue Calcium, FGM) one application/40 min, three sessions with 1 week intervals; and WBC50, 20% HP (Whiteness HP Blue Calcium) one application/50 min, three sessions with 1 week intervals. The median pH values were determined utilizing a pH meter during the initial and final gel applications. A rugosimeter was utilized to evaluate the surface roughness (Ra) before and after bleaching and brushing (100,000 strokes), and the surface wear after brushing. For the results of the pH values, there was a decrease in the pH levels from the initial to the final bleaching time, except for the WBC50. The WO and WBC40 groups exhibited higher pH values. For the results of roughness and wear, there was an increase in surface roughness and wear among the groups. The pH values tended to decrease from the initial to the final bleaching. After tooth brushing, bleaching procedures with lower pH products provided a significant increase in

  17. Software testing in roughness calculation

    International Nuclear Information System (INIS)

    Chen, Y L; Hsieh, P F; Fu, W E

    2005-01-01

    A test method to determine the function quality provided by the software for roughness measurement is presented in this study. The function quality of the software requirements should be part of and assessed through the entire life cycle of the software package. The specific function, or output accuracy, is crucial for the analysis of the experimental data. For scientific applications, however, commercial software is usually embedded with specific instrument, which is used for measurement or analysis during the manufacture process. In general, the error ratio caused by the software would be more apparent especially when dealing with relatively small quantities, like the measurements in the nanometer-scale range. The model of 'using a data generator' proposed by NPL of UK was applied in this study. An example of the roughness software is tested and analyzed by the above mentioned process. After selecting the 'reference results', the 'reference data' was generated by a programmable 'data generator'. The filter function of 0.8 mm long cutoff value, defined in ISO 11562 was tested with 66 sinusoid data at different wavelengths. Test results from commercial software and CMS written program were compared to the theoretical data calculated from ISO standards. As for the filter function in this software, the result showed a significant disagreement between the reference and test results. The short cutoff feature for filtering at the high frequencies does not function properly, while the long cutoff feature has the maximum difference in the filtering ratio, which is more than 70% between the wavelength of 300 μm and 500 μm. Conclusively, the commercial software needs to be tested more extensively for specific application by appropriate design of reference dataset to ensure its function quality

  18. Computation of surface roughness using optical correlation

    Indian Academy of Sciences (India)

    The laser speckle photography is used to calculate the average surface roughness from the autocorrelation function of the aluminum diffuse objects. The computed results of surface roughness obtained from the profile shapes of the autocorrelation function of the diffuser show good agreement with the results obtained by ...

  19. Rock discontinuity surface roughness variation with scale

    Science.gov (United States)

    Bitenc, Maja; Kieffer, D. Scott; Khoshelham, Kourosh

    2017-04-01

    ABSTRACT: Rock discontinuity surface roughness refers to local departures of the discontinuity surface from planarity and is an important factor influencing the shear resistance. In practice, the Joint Roughness Coefficient (JRC) roughness parameter is commonly relied upon and input to a shear strength criterion such as developed by Barton and Choubey [1977]. The estimation of roughness by JRC is hindered firstly by the subjective nature of visually comparing the joint profile to the ten standard profiles. Secondly, when correlating the standard JRC values and other objective measures of roughness, the roughness idealization is limited to a 2D profile of 10 cm length. With the advance of measuring technologies that provide accurate and high resolution 3D data of surface topography on different scales, new 3D roughness parameters have been developed. A desirable parameter is one that describes rock surface geometry as well as the direction and scale dependency of roughness. In this research a 3D roughness parameter developed by Grasselli [2001] and adapted by Tatone and Grasselli [2009] is adopted. It characterizes surface topography as the cumulative distribution of local apparent inclination of asperities with respect to the shear strength (analysis) direction. Thus, the 3D roughness parameter describes the roughness amplitude and anisotropy (direction dependency), but does not capture the scale properties. In different studies the roughness scale-dependency has been attributed to data resolution or size of the surface joint (see a summary of researches in [Tatone and Grasselli, 2012]). Clearly, the lower resolution results in lower roughness. On the other hand, have the investigations of surface size effect produced conflicting results. While some studies have shown a decrease in roughness with increasing discontinuity size (negative scale effect), others have shown the existence of positive scale effects, or both positive and negative scale effects. We

  20. Does Surface Roughness Amplify Wetting?

    Czech Academy of Sciences Publication Activity Database

    Malijevský, Alexandr

    2014-01-01

    Roč. 141, č. 18 (2014), s. 184703 ISSN 0021-9606 R&D Projects: GA ČR GA13-09914S Institutional support: RVO:67985858 Keywords : density functional theory * wetting * roughness Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 2.952, year: 2014

  1. Calibration of surface roughness standards

    DEFF Research Database (Denmark)

    Thalmann, R.; Nicolet, A.; Meli, F.

    2016-01-01

    The key comparison EURAMET.L-K8.2013 on roughness was carried out in the framework of a EURAMET project starting in 2013 and ending in 2015. It involved the participation of 17 National Metrology Institutes from Europe, Asia, South America and Africa representing four regional metrology organisat...

  2. Light Scattering from Rough Surfaces

    Science.gov (United States)

    1994-08-17

    us (V. Ruiz Cortes) was supported by a CONACYT and CICESE scholarship. 5. REFERENCES I.-K.A. O’Donnell and E.R. Mdndez, "Experimental study of...Calculated variation of scattenng for increasing roughness. The angle of incidence is 800. The solid line is (DAJA45-90-C-0026). VRC thanks CONACYT and for a

  3. Spectrophotometric Examination of Rough Print Surfaces

    Directory of Open Access Journals (Sweden)

    Erzsébet Novotny

    2011-05-01

    Full Text Available The objective was to assess the impact of the surface texture of individual creative paper types (coated or patternedon the quality of printing and to identify to what extent the various creative paper types require specific types ofspectrophotometers. We used stereomicroscopic images to illustrate unprinted and printed surfaces of creative papertypes. Surface roughness was measured to obtain data on the unevenness of surfaces. Spectrophotometric tests wereused to select the most suitable spectrophotometer from meters with different illumination setup for testing anygiven print. For the purpose of testing, we used spectrophotometers which are commonly available generally used totest print products for colour accuracy. With the improvement of measuring geometries, illumination setup, colourmeasurement becomes more and more capable of producing reliable results unaffected by surface textures. Our testshave proved this fact by showing that the GretagMacbeth Spectrolino with annular illumination is less sensitive tosurface texture than the X-Rite Spetrodensitometer and the Techkon SpetroDens with directional illumination. Furthertests have brought us to the conclusion that there is a difference even between the two devices with directionalillumination. While the X-Rite 530 Spectrodensitometer is more suitable for testing coated surfaces, the TechkonSpectroDens can come close to ΔE*ab values produced by the annular illuminated device for textured surfaces.

  4. Effect of Surface Roughness on Hydrodynamic Bearings

    Science.gov (United States)

    Majumdar, B. C.; Hamrock, B. J.

    1981-01-01

    A theoretical analysis on the performance of hydrodynamic oil bearings is made considering surface roughness effect. The hydrodynamic as well as asperity contact load is found. The contact pressure was calculated with the assumption that the surface height distribution was Gaussian. The average Reynolds equation of partially lubricated surface was used to calculate hydrodynamic load. An analytical expression for average gap was found and was introduced to modify the average Reynolds equation. The resulting boundary value problem was then solved numerically by finite difference methods using the method of successive over relaxation. The pressure distribution and hydrodynamic load capacity of plane slider and journal bearings were calculated for various design data. The effects of attitude and roughness of surface on the bearing performance were shown. The results are compared with similar available solution of rough surface bearings. It is shown that: (1) the contribution of contact load is not significant; and (2) the hydrodynamic and contact load increase with surface roughness.

  5. Specular Reflection from Rough Surfaces Revisited

    Science.gov (United States)

    Yasuda, Kensei; Kim, Alvin; Cho, Hayley; Timofejev, Timofej; Walecki, Wojciech J.; Klep, James; Edelson, Amy S.; Walecki, Abigail S.; Walecki, Eve S.; Walecki, Peter S.

    2016-01-01

    In his beautiful paper, Hasan Fakhruddin reported observations of mirror-like reflections in the rough surface of a ground glass plate. Similar effects have been recently employed for metrology of the roughness of optical diffusers used in modern light emitting device illumination systems. We report the observations of specular reflection in…

  6. Friction behaviors of rough chromium surfaces under starving lubrication conditions

    Science.gov (United States)

    Liu, Derong; Yan, Bo; Shen, Bin; Liu, Lei; Hu, Wenbin

    2018-01-01

    Surface texturing has become an effective method for improving the tribological properties of mechanical components under the oil lubrication. In this study, a rough surface, with the bumps arranged in a random array, was prepared by means of electrodeposition. A post-grinding and polishing processing was employed to fabricate flat areas for tribological tests under conformal contact. Compared with the smooth surfaces, the rough surface improves the load capacity of coatings at high loads. The effects of rough surfaces on friction reduction become more pronounced at higher speeds and lower normal loads due to the transition of lubricant regime from the boundary to mixed lubrication.

  7. Diffuse reflection of ultracold neutrons from low-roughness surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Atchison, F.; Daum, M.; Henneck, R.; Horisberger, M.; Kirch, K.; Lauss, B.; Mtchedlishvili, A.; Meier, M.; Petzoldt, G.; Schelldorfer, R.; Zsigmond, G. [Paul Scherrer Institut, PSI, Villigen (Switzerland); Heule, S.; Knecht, A. [Paul Scherrer Institut, PSI, Villigen (Switzerland); University Zuerich, Zuerich (Switzerland); Kasprzak, M. [Paul Scherrer Institut, PSI, Villigen (Switzerland); Stefan Meyer Institut, Vienna (Austria); Kuzniak, M. [Paul Scherrer Institut, PSI, Villigen (Switzerland); Jagiellonian University, Smoluchowski Institute of Physics, Cracow (Poland); Plonka-Spehr, C. [Institut Laue Langevin, ILL, Grenoble (France); Straumann, U. [University Zuerich, Zuerich (Switzerland)

    2010-04-15

    We report a measurement of the reflection of ultracold neutrons from flat, large-area plates of different Fermi potential materials with low surface roughness. The results were used to test two diffuse reflection models, the well-known Lambert model and the micro-roughness model which is based on wave scattering. The Lambert model fails to reproduce the diffuse reflection data. The surface roughness b and correlation length w, obtained by fitting the micro-roughness model to the data are in the range 1{<=}b{<=}3 nm and 10{<=}w{<=}120 nm, in qualitative agreement with independent measurements using atomic force microscopy. (orig.)

  8. Diffuse reflection of ultracold neutrons from low-roughness surfaces

    International Nuclear Information System (INIS)

    Atchison, F.; Daum, M.; Henneck, R.; Horisberger, M.; Kirch, K.; Lauss, B.; Mtchedlishvili, A.; Meier, M.; Petzoldt, G.; Schelldorfer, R.; Zsigmond, G.; Heule, S.; Knecht, A.; Kasprzak, M.; Kuzniak, M.; Plonka-Spehr, C.; Straumann, U.

    2010-01-01

    We report a measurement of the reflection of ultracold neutrons from flat, large-area plates of different Fermi potential materials with low surface roughness. The results were used to test two diffuse reflection models, the well-known Lambert model and the micro-roughness model which is based on wave scattering. The Lambert model fails to reproduce the diffuse reflection data. The surface roughness b and correlation length w, obtained by fitting the micro-roughness model to the data are in the range 1≤b≤3 nm and 10≤w≤120 nm, in qualitative agreement with independent measurements using atomic force microscopy. (orig.)

  9. SMEX03 Surface Roughness Data, Alabama

    Data.gov (United States)

    National Aeronautics and Space Administration — The data set SMEX03 Surface Roughness Data is comprised of data collected over the regional study areas of Alabama, Georgia, and Oklahoma, USA as part of the 2003...

  10. SMAPVEX08 Surface Roughness Data V001

    Data.gov (United States)

    National Aeronautics and Space Administration — Surface roughness data for this data set were collected at several field sites as part of the Soil Moisture Active Passive Validation Experiment 2008 (SMAPVEX08)...

  11. Growth of rough epitaxial surfaces

    Indian Academy of Sciences (India)

    relevant to atomic surfaces would automatically be satisfied by largely heuristic classical terms. We therefore have to present electronic energy calculations in support of our model of surface growth. Among various physical processes which have been taken into account in models of growing interfaces, surface diffusion has ...

  12. [Wear intensity and surface roughness of microhybrid composite and ceramic occlusal veneers on premolars after the thermocycling and cyclic mechanical loading tests].

    Science.gov (United States)

    Zhang, H Y; Jiang, T; Cheng, M X; Zhang, Y W

    2018-02-18

    To evaluate the wear intensity and surface roughness of occlusal veneers on premolars made of microhybrid composite resin or two kinds of ceramics in vitro after the thermocycling and cyclic mechanical loading tests. In the study,24 fresh extracted human premolars without root canal treatment were prepared (cusps reduction of 1.5 mm in thickness to simulate middle to severe tooth wear, the inclinations of cusps were 20°). The prepared teeth were restored with occlusal veneers made of three different materials: microhybrid composite, heat-pressed lithium disilicate ceramic and computer-aided design/computer-aided manufacturing (CAD/CAM) lithium disilicate ceramic in the thickness of 1.5 mm. The occlusal veneers were cemented with resin cement. The specimens were fatigued using the thermocycling and cyclic mechanical loading tests after being stored in water for 72 h. The wear of specimens was measured using gypsum replicas and 3D laser scanner before and after the thermocycling and cyclic mechanical loading tests and the mean lost distance (mm) was used to indicate the level of wear. The surfaces of occlusal contact area were observed and the surface roughness was recorded using 3D laser scanning confocal microscope before and after the fatigue test. Differences between the groups were compared using ONE-way ANOVA(Pmechanical loading tests. The mean wear of microhybrid composite group, heat-pressed lithium disilicate ceramic group, and CAD/CAM lithium disilicate ceramic group was (-0.13±0.03) mm, (-0.05±0.01) mm and (-0.05±0.01) mm, the wear of microhybrid composite was significantly higher than the two ceramic groups(PCAD/CAM lithium disilicate ceramic (P=0.010). From the view of wear speed, microhybrid composite was significantly higher than the two kinds of ceramics, but it was similar to enamel when the opposing tooth was natural. The surface roughness before the themocycling and cyclic mechanical loading test of microhybrid composite was significantly

  13. Surface roughness effects on turbulent Couette flow

    Science.gov (United States)

    Lee, Young Mo; Lee, Jae Hwa

    2017-11-01

    Direct numerical simulation of a turbulent Couette flow with two-dimensional (2-D) rod roughness is performed to examine the effects of the surface roughness. The Reynolds number based on the channel centerline laminar velocity (Uco) and channel half height (h) is Re =7200. The 2-D rods are periodically arranged with a streamwise pitch of λ = 8 k on the bottom wall, and the roughness height is k = 0.12 h. It is shown that the wall-normal extent for the logarithmic layer is significantly shortened in the rough-wall turbulent Couette flow, compared to a turbulent Couette flow with smooth wall. Although the Reynolds stresses are increased in a turbulent channel flow with surface roughness in the outer layer due to large-scale ejection motions produced by the 2-D rods, those of the rough-wall Couette flow are decreased. Isosurfaces of the u-structures averaged in time suggest that the decrease of the turbulent activity near the centerline is associated with weakened large-scale counter-rotating roll modes by the surface roughness. This research was supported by the National Research Foundation of Korea (NRF) funded by the Ministry of Education (NRF-2017R1D1A1A09000537) and the Ministry of Science, ICT & Future Planning (NRF-2017R1A5A1015311).

  14. Dissolution of minerals with rough surfaces

    Science.gov (United States)

    de Assis, Thiago A.; Aarão Reis, Fábio D. A.

    2018-05-01

    We study dissolution of minerals with initial rough surfaces using kinetic Monte Carlo simulations and a scaling approach. We consider a simple cubic lattice structure, a thermally activated rate of detachment of a molecule (site), and rough surface configurations produced by fractional Brownian motion algorithm. First we revisit the problem of dissolution of initial flat surfaces, in which the dissolution rate rF reaches an approximately constant value at short times and is controlled by detachment of step edge sites. For initial rough surfaces, the dissolution rate r at short times is much larger than rF ; after dissolution of some hundreds of molecular layers, r decreases by some orders of magnitude across several time decades. Meanwhile, the surface evolves through configurations of decreasing energy, beginning with dissolution of isolated sites, then formation of terraces with disordered boundaries, their growth, and final smoothing. A crossover time to a smooth configuration is defined when r = 1.5rF ; the surface retreat at the crossover is approximately 3 times the initial roughness and is temperature-independent, while the crossover time is proportional to the initial roughness and is controlled by step-edge site detachment. The initial dissolution process is described by the so-called rough rates, which are measured for fixed ratios between the surface retreat and the initial roughness. The temperature dependence of the rough rates indicates control by kink site detachment; in general, it suggests that rough rates are controlled by the weakest microscopic bonds during the nucleation and formation of the lowest energy configurations of the crystalline surface. Our results are related to recent laboratory studies which show enhanced dissolution in polished calcite surfaces. In the application to calcite dissolution in alkaline environment, the minimal values of recently measured dissolution rate spectra give rF ∼10-9 mol/(m2 s), and the calculated rate

  15. Adhesive contact of randomly rough surfaces

    Science.gov (United States)

    Pastewka, Lars; Robbins, Mark

    2012-02-01

    The contact area, stiffness and adhesion between rigid, randomly rough surfaces and elastic substrates is studied using molecular statics and continuum simulations. The surfaces are self-affine with Hurst exponent 0.3 to 0.8 and different short λs and long λL wavelength cutoffs. The rms surface slope and the range and strength of the adhesive potential are also varied. For parameters typical of most solids, the effect of adhesion decreases as the ratio λL/λs increases. In particular, the pull-off force decreases to zero and the area of contact Ac becomes linear in the applied load L. A simple scaling argument is developed that describes the increase in the ratio Ac/L with increasing adhesion and a corresponding increase in the contact stiffness [1]. The argument also predicts a crossover to finite contact area at zero load when surfaces are exceptionally smooth or the ratio of surface tension to bulk modulus is unusually large, as for elastomers. Results that test this prediction will be presented and related to the Maugis-Dugdale [2] theories for individual asperities and the more recent scaling theory of Persson [3]. [1] Akarapu, Sharp, Robbins, Phys. Rev. Lett. 106, 204301 (2011) [2] Maugis, J. Colloid Interface Sci. 150, 243 (1992) [3] Persson, Phys. Rev. Lett. 74, 75420 (2006)

  16. Surface roughness reduction using spray-coated hydrogen silsesquioxane reflow

    Science.gov (United States)

    Cech, Jiri; Pranov, Henrik; Kofod, Guggi; Matschuk, Maria; Murthy, Swathi; Taboryski, Rafael

    2013-09-01

    Surface roughness or texture is the most visible property of any object, including injection molded plastic parts. Roughness of the injection molding (IM) tool cavity directly affects not only appearance and perception of quality, but often also the function of all manufactured plastic parts. So called “optically smooth” plastic surfaces is one example, where low roughness of a tool cavity is desirable. Such tool surfaces can be very expensive to fabricate using conventional means, such as abrasive diamond polishing or diamond turning. We present a novel process to coat machined metal parts with hydrogen silsesquioxane (HSQ) to reduce their surface roughness. Results from the testing of surfaces made from two starting roughnesses are presented; one polished with grit 2500 sandpaper, another with grit 11.000 diamond polishing paste. We characterize the two surfaces with AFM, SEM and optical profilometry before and after coating. We show that the HSQ coating is able to reduce peak-to-valley roughness more than 20 times on the sandpaper polished sample, from 2.44(±0.99) μm to 104(±22) nm and more than 10 times for the paste polished sample from 1.85(±0.63) μm to 162(±28) nm while roughness averages are reduced 10 and 3 times respectively. We completed more than 10,000 injection molding cycles without detectable degradation of the HSQ coating. This result opens new possibilities for molding of affordable plastic parts with perfect surface finish.

  17. A possibility of avoiding surface roughness due to insects

    Science.gov (United States)

    Wortmann, F. X.

    1984-01-01

    Discussion of a method for eliminating turbulence caused by the formation of insect roughness upon the leading edges and fuselage, particularly in aircraft using BLC. The proposed technique foresees the use of elastic surfaces on which insect roughness cannot form. The operational characteristics of highly elastic rubber surface fastened to the wing leading edges and fuselage edges are examined. Some preliminary test results are presented. The technique is seen to be advantageous primarily for short-haul operations.

  18. Spin Hall effect by surface roughness

    KAUST Repository

    Zhou, Lingjun

    2015-01-08

    The spin Hall and its inverse effects, driven by the spin orbit interaction, provide an interconversion mechanism between spin and charge currents. Since the spin Hall effect generates and manipulates spin current electrically, to achieve a large effect is becoming an important topic in both academia and industries. So far, materials with heavy elements carrying a strong spin orbit interaction, provide the only option. We propose here a new mechanism, using the surface roughness in ultrathin films, to enhance the spin Hall effect without heavy elements. Our analysis based on Cu and Al thin films suggests that surface roughness is capable of driving a spin Hall angle that is comparable to that in bulk Au. We also demonstrate that the spin Hall effect induced by surface roughness subscribes only to the side-jump contribution but not the skew scattering. The paradigm proposed in this paper provides the second, not if only, alternative to generate a sizable spin Hall effect.

  19. How to make a soft, rough surface transparent

    Science.gov (United States)

    Helseth, L. E.

    2017-09-01

    A transparent elastomer is made opaque by making one of its surfaces rough. By squeezing the rough surface against a piece of glass, the roughness is smoothed out and the elastomer becomes transparent.

  20. Effects of bleaching agents on surface roughness of filling materials.

    Science.gov (United States)

    Markovic, Ljubisa; Jordan, Rainer Andreas; Glasser, Marie-Claire; Arnold, Wolfgang Hermann; Nebel, Jan; Tillmann, Wolfgang; Ostermann, Thomas; Zimmer, Stefan

    2014-01-01

    The aim of this study was to use a non-tactile optical measurement system to assess the effects of three bleaching agents' concentrations on the surface roughness of dental restoration materials. Two composites (Grandio, Venus) and one glass ionomer cement (Ketac Fil Plus) were used in this in vitro study. Specimens were treated with three different bleaching agents (16% and 22% carbamide peroxide (Polanight) and 38% hydrogen peroxide (Opalescence Boost)). Surface roughness was measured with an optical profilometer (Infinite Focus G3) before and after the bleaching treatment. Surface roughness increased in all tested specimens after bleaching treatment (p<0.05). Our in vitro study showed that dental bleaching agents influenced the surface roughness of different restoration materials, and the restoration material itself was shown to have an impact on alteration susceptibility. There seemed to be no clinical relevance in case of an optimal finish.

  1. Single-layer model for surface roughness.

    Science.gov (United States)

    Carniglia, C K; Jensen, D G

    2002-06-01

    Random roughness of an optical surface reduces its specular reflectance and transmittance by the scattering of light. The reduction in reflectance can be modeled by a homogeneous layer on the surface if the refractive index of the layer is intermediate to the indices of the media on either side of the surface. Such a layer predicts an increase in the transmittance of the surface and therefore does not provide a valid model for the effects of scatter on the transmittance. Adding a small amount of absorption to the layer provides a model that predicts a reduction in both reflectance and transmittance. The absorbing layer model agrees with the predictions of a scalar scattering theory for a layer with a thickness that is twice the rms roughness of the surface. The extinction coefficient k for the layer is proportional to the thickness of the layer.

  2. High speed machined surface roughness measurement ...

    African Journals Online (AJOL)

    Surface roughness monitoring techniques using non-contact methods based on computer vision technology are becoming popular and cost effective. An evolvable hardware configuration using reconfigurable Xilinx Virtex FPGA xcv1000 architecture with capability to compensate for poor illumination environment is ...

  3. Optical measurement of surface roughness in manufacturing

    Energy Technology Data Exchange (ETDEWEB)

    Brodmann, R.

    1984-11-01

    The measuring system described here is based on the light-scattering method, and was developed by Optische Werke G. Rodenstock, Munich. It is especially useful for rapid non-contact monitoring of surface roughness in production-related areas. This paper outlines the differences between this system and the common stylus instrument, including descriptions of some applications in industry.

  4. Plasticity under rough surface contact and friction

    NARCIS (Netherlands)

    Sun, F.

    2016-01-01

    The ultimate objective of this work is to gain a better understanding of the plastic behavior of rough metal surfaces under contact loading. Attention in this thesis focuses on the study of single and multiple asperities with micrometer scale dimensions, a scale at which plasticity is known to be

  5. Surface roughness and wear of resin cements after toothbrush abrasion

    Directory of Open Access Journals (Sweden)

    Sérgio Kiyoshi ISHIKIRIAMA

    2015-01-01

    Full Text Available Increased surface roughness and wear of resin cements may cause failure of indirect restorations. The aim of this study was to evaluate quantitatively the surface roughness change and the vertical wear of four resin cements subjected to mechanical toothbrushing abrasion. Ten rectangular specimens (15 × 5 × 4 mm were fabricated according to manufacturer instructions for each group (n = 10: Nexus 3, Kerr (NX3; RelyX ARC, 3M ESPE (ARC; RelyX U100, 3M ESPE (U100; and Variolink II, Ivoclar/Vivadent (VL2. Initial roughness (Ra, µm was obtained through 5 readings with a roughness meter. Specimens were then subjected to toothbrushing abrasion (100,000 cycles, and further evaluation was conducted for final roughness. Vertical wear (µm was quantified by 3 readings of the real profile between control and brushed surfaces. Data were subjected to analysis of variance, followed by Tukey’s test (p < 0.05. The Pearson correlation test was performed between the surface roughness change and wear (p < 0.05. The mean values of initial/final roughness (Ra, µm/wear (µm were as follows: NX3 (0.078/0.127/23.175; ARC (0.086/0.246/20.263; U100 (0.296/0.589/16.952; and VL2 (0.313/0.512/22.876. Toothbrushing abrasion increased surface roughness and wear of all resin cements tested, although no correlation was found between those variables. Vertical wear was similar among groups; however, it was considered high and may lead to gap formation in indirect restorations.

  6. Modeling superhydrophobic surfaces comprised of random roughness

    Science.gov (United States)

    Samaha, M. A.; Tafreshi, H. Vahedi; Gad-El-Hak, M.

    2011-11-01

    We model the performance of superhydrophobic surfaces comprised of randomly distributed roughness that resembles natural surfaces, or those produced via random deposition of hydrophobic particles. Such a fabrication method is far less expensive than ordered-microstructured fabrication. The present numerical simulations are aimed at improving our understanding of the drag reduction effect and the stability of the air-water interface in terms of the microstructure parameters. For comparison and validation, we have also simulated the flow over superhydrophobic surfaces made up of aligned or staggered microposts for channel flows as well as streamwise or spanwise ridge configurations for pipe flows. The present results are compared with other theoretical and experimental studies. The numerical simulations indicate that the random distribution of surface roughness has a favorable effect on drag reduction, as long as the gas fraction is kept the same. The stability of the meniscus, however, is strongly influenced by the average spacing between the roughness peaks, which needs to be carefully examined before a surface can be recommended for fabrication. Financial support from DARPA, contract number W91CRB-10-1-0003, is acknowledged.

  7. Dependence of Pin Surface Roughness for Friction Forces of Ultrathin Perfluoropolyether Lubricant Film on Magnetic Disks by Pin-on-Disk Test

    Directory of Open Access Journals (Sweden)

    H. Tani

    2012-01-01

    Full Text Available We fabricated supersmooth probes for use in pin-on-disk sliding tests by applying gas cluster ion beam irradiation to glass convex lenses. In the fabrication process, various changes were made to the irradiation conditions; these included one-step irradiation of Ar clusters or two-step irradiation of Ar and N2 clusters, with or without Ar cluster-assisted tough carbon deposition prior to N2 irradiation, and the application of various ion doses onto the surface. We successfully obtained probes with a centerline averaged surface roughness that ranged widely from 1.08 to 4.30 nm. Using these probes, we measured the friction forces exerted on magnetic disks coated with a molecularly thin lubricant film. Perfluoropolyether lubricant films with different numbers of hydroxyl end groups were compared, and our results indicated that the friction force increases as the surface roughness of the pin decreases and that increases as the number of hydroxyl end groups increases.

  8. Multiscale Characterization of Joint Surface Roughness

    Science.gov (United States)

    Nigon, Benoit; Englert, Andreas; Pascal, Christophe; Saintot, Aline

    2017-12-01

    Recent studies provided detailed characterizations of fault (i.e., shear fracture) roughness at different length scales. Similar investigation for joints (i.e., tensile fractures) are seldom and not as detailed. The present study aims at characterizing joint plumose patterns. We investigated the scale-dependent surface roughness properties of S-type plumoses. Joint surface measurements at relatively large scales were carried out with Light Detection and Ranging (LiDAR) technology. Joint surface measurements at the microscopic scale were carried out based on a noncontact optical method, using a Keyence VHX-2000D microscope. Three parameters were used to characterize fracture surface elevation, standard deviation, Hurst exponent, and correlation length through 3 scale length orders of magnitude. Our study showed that standard deviation and correlation length decrease with scale, similarly to previous findings on faults. In addition, the range of Hurst exponents as a function of scale for the studied joint surface agrees well with those previously found for faults. However, directional analysis showed that correlation length and Hurst exponent of joint surfaces at scales smaller than 1 dm differ significantly from the ones of fault surfaces. In contrast to fault surface ornaments that are mainly characterized by linear structures, plumose structures show marked variability in orientation and anisotropy as a function of position on the joint surface.

  9. The surface roughness and planetary boundary layer

    Science.gov (United States)

    Telford, James W.

    1980-03-01

    Applications of the entrainment process to layers at the boundary, which meet the self similarity requirements of the logarithmic profile, have been studied. By accepting that turbulence has dominating scales related in scale length to the height above the surface, a layer structure is postulated wherein exchange is rapid enough to keep the layers internally uniform. The diffusion rate is then controlled by entrainment between layers. It has been shown that theoretical relationships derived on the basis of using a single layer of this type give quantitatively correct factors relating the turbulence, wind and shear stress for very rough surface conditions. For less rough surfaces, the surface boundary layer can be divided into several layers interacting by entrainment across each interface. This analysis leads to the following quantitatively correct formula compared to published measurements. 1 24_2004_Article_BF00877766_TeX2GIFE1.gif {σ _w }/{u^* } = ( {2/{9Aa}} )^{{1/4}} ( {1 - 3^{{1/2}{ a/k{d_n }/z{σ _w }/{u^* }z/L} )^{{1/4}} = 1.28(1 - 0.945({{σ _w }/{u^* }}}) {{z/L}})^{{1/4 where u^* = ( {{tau/ρ}}^{{1/2}}, σ w is the standard deviation of the vertical velocity, z is the height and L is the Obukhov scale lenght. The constants a, A, k and d n are the entrainment constant, the turbulence decay constant, Von Karman's constant, and the layer depth derived from the theory. Of these, a and A, are universal constants and not empirically determined for the boundary layer. Thus the turbulence needed for the plume model of convection, which resides above these layers and reaches to the inversion, is determined by the shear stress and the heat flux in the surface layers. This model applies to convection in cool air over a warm sea. The whole field is now determined except for the temperature of the air relative to the water, and the wind, which need a further parameter describing sea surface roughness. As a first stop to describing a surface where roughness elements

  10. Computation of surface roughness using optical correlation

    Indian Academy of Sciences (India)

    [13] E Marx and T V Vorburger, Appl. Opt. 29, 3613 (1990). [14] R Silvennoinen, K E Peiponen, T Asakura, Y Zhang, C Gu, K Ikonen and E J Morley,. Opt. Lasers Eng. 17, 103 (1992). [15] M Sato Kurita, M Sato and K Nakano, Int. J. Jpn. Soc. Mech. Eng. 35, 335 (1992). [16] P Beckmann, Scattering of light by rough surfaces, ...

  11. The effect of toothbrush bristle stiffness on nanohybrid surface roughness

    Science.gov (United States)

    Zairani, O.; Irawan, B.; Damiyanti, M.

    2017-08-01

    The surface of a restoration can be affected by toothpaste containing abrasive agents and the stiffness of toothbrush bristles. Objective: To identify the effect of toothbrush bristle stiffness on nanohybrid surface roughness. Methods: Sixteen nanohybrid specimens were separated into two groups. The first group was brushed using soft-bristle toothbrushes, and the second group was brushed using medium-bristle toothbrushes. Media such as aqua bides was used for brushing in both groups. Brushing was done 3 times for 5 minutes. Surface roughness was measured initially and at 5, 10, and 15 minutes using a surface roughness tester. Results: The results, tested with One-Way ANOVA and Independent Samples t Test, demonstrated that after brushing for 15 minutes, the soft-bristle toothbrush group showed a significantly different value (p toothbrushes showed the value of nano hybrid surface roughness significant difference after brushing for 10 minutes. Conclusion: Roughness occurs more rapidly when brushing with medium-bristle tooth brushes than when brushing with soft-bristle toothbrushes.

  12. Determination of forest road surface roughness by Kinect depth imaging

    Directory of Open Access Journals (Sweden)

    Francesco Marinello

    2017-12-01

    Full Text Available Roughness is a dynamic property of the gravel road surface that affects safety, ride comfort as well as vehicle tyre life and maintenance costs. A rapid survey of gravel road condition is fundamental for an effective maintenance planning and definition of the intervention priorities.Different non-contact techniques such as laser scanning, ultrasonic sensors and photogrammetry have recently been proposed to reconstruct three-dimensional topography of road surface and allow extraction of roughness metrics. The application of Microsoft Kinect™ depth camera is proposed and discussed here for collection of 3D data sets from gravel roads, to be implemented in order to allow quantification of surface roughness.The objectives are to: i verify the applicability of the Kinect sensor for characterization of different forest roads, ii identify the appropriateness and potential of different roughness parameters and iii analyse the correlation with vibrations recoded by 3-axis accelerometers installed on different vehicles. The test took advantage of the implementation of the Kinect depth camera for surface roughness determination of 4 different forest gravel roads and one well-maintained asphalt road as reference. Different vehicles (mountain bike, off-road motorcycle, ATV vehicle, 4WD car and compact crossover were included in the experiment in order to verify the vibration intensity when travelling on different road surface conditions. Correlations between the extracted roughness parameters and vibration levels of the tested vehicles were then verified. Coefficients of determination of between 0.76 and 0.97 were detected between average surface roughness and standard deviation of relative accelerations, with higher values in the case of lighter vehicles.

  13. SMEX02 Land Surface Information: Geolocation, Surface Roughness, and Photographs

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set combines various ancillary data (geolocation, surface roughness, and photographs) collected for the Iowa Soil Moisture Experiment 2002 (SMEX02) study...

  14. Surface roughness retrieval from radar data

    Science.gov (United States)

    Chauhan, Narinder S.; Engman, Edwin T.

    1995-01-01

    Radar data from the remote sensing technique have been used in conjunction with theoretical microwave modeling to develop a retrieval algorithm for the root mean square height of the rough surface. The algorithm exploits frequency (L and C band) differences in the radar response from a vegetated rough surface. These differences are related back to the Fresnel reflectivity and surface rms height by using a theoretical modeling approach that is based on a discrete scatter random media technique and uses distorted Born approximation to compute backscatter coefficient from a particular scene. Sensitivity analysis shows that the change in surface reflectivity due to the change in frequency from L to C band is dominated by surface rms height, and, the Fresnel reflectivity stays almost constant over this frequency interval. The inversion algorithm based on these sensitivity differences has been applied to the backscatter model data from a plant canopy of soybean. Calculations show that the technique gives accurate results from a model backscatter data set that is corrupted with 80% of noise. The inversion algorithm is also applied to synthetic aperture radar (SAR) data collected over corn fields during the MACHYDRO'90 experiment in Pennsylvania, USA. There is an excellent agreement between the measured and the retrieved rms surface height.

  15. Contact stiffness of randomly rough surfaces.

    Science.gov (United States)

    Pohrt, Roman; Popov, Valentin L

    2013-11-21

    We investigate the contact stiffness of an elastic half-space and a rigid indenter with randomly rough surface having a power spectrum C2D(q)proportional q(-2H-2), where q is the wave vector. The range of H[symbol: see text] is studied covering a wide range of roughness types from white noise to smooth single asperities. At low forces, the contact stiffness is in all cases a power law function of the normal force with an exponent α. For H > 2, the simple Hertzian behavior is observed . In the range of 0 dimensional contact mechanics and the method of dimensionality reduction (MDR). The influence of the long wavelength roll-off is investigated and discussed.

  16. Robust surface roughness indices and morphological interpretation

    Science.gov (United States)

    Trevisani, Sebastiano; Rocca, Michele

    2016-04-01

    Geostatistical-based image/surface texture indices based on variogram (Atkison and Lewis, 2000; Herzfeld and Higginson, 1996; Trevisani et al., 2012) and on its robust variant MAD (median absolute differences, Trevisani and Rocca, 2015) offer powerful tools for the analysis and interpretation of surface morphology (potentially not limited to solid earth). In particular, the proposed robust index (Trevisani and Rocca, 2015) with its implementation based on local kernels permits the derivation of a wide set of robust and customizable geomorphometric indices capable to outline specific aspects of surface texture. The stability of MAD in presence of signal noise and abrupt changes in spatial variability is well suited for the analysis of high-resolution digital terrain models. Moreover, the implementation of MAD by means of a pixel-centered perspective based on local kernels, with some analogies to the local binary pattern approach (Lucieer and Stein, 2005; Ojala et al., 2002), permits to create custom roughness indices capable to outline different aspects of surface roughness (Grohmann et al., 2011; Smith, 2015). In the proposed poster, some potentialities of the new indices in the context of geomorphometry and landscape analysis will be presented. At same time, challenges and future developments related to the proposed indices will be outlined. Atkinson, P.M., Lewis, P., 2000. Geostatistical classification for remote sensing: an introduction. Computers & Geosciences 26, 361-371. Grohmann, C.H., Smith, M.J., Riccomini, C., 2011. Multiscale Analysis of Topographic Surface Roughness in the Midland Valley, Scotland. IEEE Transactions on Geoscience and Remote Sensing 49, 1220-1213. Herzfeld, U.C., Higginson, C.A., 1996. Automated geostatistical seafloor classification - Principles, parameters, feature vectors, and discrimination criteria. Computers and Geosciences, 22 (1), pp. 35-52. Lucieer, A., Stein, A., 2005. Texture-based landform segmentation of LiDAR imagery

  17. Surface roughness of orthodontic band cements with different compositions

    Directory of Open Access Journals (Sweden)

    Françoise Hélène van de Sande

    2011-06-01

    Full Text Available OBJECTIVES: The present study evaluated comparatively the surface roughness of four orthodontic band cements after storage in various solutions. MATERIAL AND METHODS: Eight standardized cylinders were made from 4 materials: zinc phosphate cement (ZP, compomer (C, resin-modified glass ionomer cement (RMGIC and resin cement (RC. Specimens were stored for 24 h in deionized water and immersed in saline (pH 7.0 or 0.1 M lactic acid solution (pH 4.0 for 15 days. Surface roughness readings were taken with a profilometer (Surfcorder SE1200 before and after the storage period. Data were analyzed by two-way ANOVA and Tukey's test (comparison among cements and storage solutions or paired t-test (comparison before and after the storage period at 5% significance level. RESULTS: The values for average surface roughness were statistically different (pRMGIC>C>R (p0.05. Compared to the current threshold (0.2 µm related to biofilm accumulation, both RC and C remained below the threshold, even after acidic challenge by immersion in lactic acid solution. CONCLUSIONS: Storage time and immersion in lactic acid solution increased the surface roughness of the majority of the tested cements. RC presented the smoothest surface and it was not influenced by storage conditions.

  18. Mapping gullies, dunes, lava fields, and landslides via surface roughness

    Science.gov (United States)

    Korzeniowska, Karolina; Pfeifer, Norbert; Landtwing, Stephan

    2018-01-01

    Gully erosion is a widespread and significant process involved in soil and land degradation. Mapping gullies helps to quantify past, and anticipate future, soil losses. Digital terrain models offer promising data for automatically detecting and mapping gullies especially in vegetated areas, although methods vary widely measures of local terrain roughness are the most varied and debated among these methods. Rarely do studies test the performance of roughness metrics for mapping gullies, limiting their applicability to small training areas. To this end, we systematically explored how local terrain roughness derived from high-resolution Light Detection And Ranging (LiDAR) data can aid in the unsupervised detection of gullies over a large area. We also tested expanding this method for other landforms diagnostic of similarly abrupt land-surface changes, including lava fields, dunes, and landslides, as well as investigating the influence of different roughness thresholds, resolutions of kernels, and input data resolution, and comparing our method with previously published roughness algorithms. Our results show that total curvature is a suitable metric for recognising analysed gullies and lava fields from LiDAR data, with comparable success to that of more sophisticated roughness metrics. Tested dunes or landslides remain difficult to distinguish from the surrounding landscape, partly because they are not easily defined in terms of their topographic signature.

  19. Wave scattering from statistically rough surfaces

    CERN Document Server

    Bass, F G; ter Haar, D

    2013-01-01

    Wave Scattering from Statistically Rough Surfaces discusses the complications in radio physics and hydro-acoustics in relation to wave transmission under settings seen in nature. Some of the topics that are covered include radar and sonar, the effect of variations in topographic relief or ocean waves on the transmission of radio and sound waves, the reproduction of radio waves from the lower layers of the ionosphere, and the oscillations of signals within the earth-ionosphere waveguide. The book begins with some fundamental idea of wave transmission theory and the theory of random processes a

  20. Surface roughness of composite resins subjected to hydrochloric acid.

    Science.gov (United States)

    Roque, Ana Carolina Cabral; Bohner, Lauren Oliveira Lima; de Godoi, Ana Paula Terossi; Colucci, Vivian; Corona, Silmara Aparecida Milori; Catirse, Alma Blásida Concepción Elizaur Benitez

    2015-01-01

    The purpose of this study was to determine the influence of hydrochloric acid on surface roughness of composite resins subjected to brushing. Sixty samples measuring 2 mm thick x 6 mm diameter were prepared and used as experimental units. The study presented a 3x2 factorial design, in which the factors were composite resin (n=20), at 3 levels: microhybrid composite (Z100), nanofilled composite (FiltekTM Supreme), nanohybrid composite (Ice), and acid challenge (n=10) at 2 levels: absence and presence. Acid challenge was performed by immersion of specimens in hydrochloric acid (pH 1.2) for 1 min, 4 times per day for 7 days. The specimens not subjected to acid challenge were stored in 15 mL of artificial saliva at 37 oC. Afterwards, all specimens were submitted to abrasive challenge by a brushing cycle performed with a 200 g weight at a speed of 356 rpm, totaling 17.8 cycles. Surface roughness measurements (Ra) were performed and analyzed by ANOVA and Tukey test (p≤0.05). Surface roughness values were higher in the presence (1.07±0.24) as compared with the absence of hydrochloric acid (0.72±0.04). Surface roughness values were higher for microhybrid (1.01±0.27) compared with nanofilled (0.68 ±0.09) and nanohybrid (0.48±0.15) composites when the specimens were not subjects to acid challenge. In the presence of hydrochloric acid, microhybrid (1.26±0.28) and nanofilled (1.18±0,30) composites presents higher surface roughness values compared with nanohybrid (0.77±0.15). The hydrochloric acid affected the surface roughness of composite resin subjected to brushing.

  1. Light depolarization in off-specular reflection on submicro rough metal surfaces with imperfectly random roughness.

    Science.gov (United States)

    Liu, Linsheng; Li, Xuefeng; Nonaka, Kazuhiro

    2015-02-01

    Depolarization at a rough surface relates to its roughness and irregularity (e.g., sags and crests) besides the material property. However, there is still lack of general theory to clearly describe the relationship between depolarization ratios and surface conditions, and one important reason is that the mechanism of depolarization relates to geometric parameters such as microcosmic height/particle distributions of sub-micro to nm levels. To study the mechanism in more detail, a compact laser instrument is developed, and depolarization information of a linearly polarized incident light is used for analyzing the roughness, during which a He-Ne laser source (λ = 632.8 nm) is used. Three nickel specimens with RMS roughness (Rq) less than λ/4 are fabricated and tested. Six different areas in each specimen are characterized in detail using an AFM. Rq are in the range of 34.1-155.0 nm, and the heights are non-Gaussian distribution in the first specimen and near-Gaussian distribution in the others. Off-specular inspection is carried out exactly on these 18 characterized areas, and results show that the cross-polarization ratios match quite well with Rq values of the first sample that has Rq ≤ λ/10 (or Rt ≤ λ), while they match well with maximum height, Rt, values of the other two that have Rt > λ (the maximum derivation is 11%). In addition, since this instrument is simple, portable, stable, and low-cost, it has great potential for practical online roughness testing after a linear calibration.

  2. Rough surface mitigates electron and gas emission

    International Nuclear Information System (INIS)

    Molvik, A.

    2004-01-01

    Heavy-ion beams impinging on surfaces near grazing incidence (to simulate the loss of halo ions) generate copious amounts of electrons and gas that can degrade the beam. We measured emission coefficients of η e (le) 130 and η 0 ∼ 10 4 respectively, with 1 MeV K + incident on stainless steel. Electron emission scales as η e ∝ 1/cos(θ), where θ is the ion angle of incidence relative to normal. If we were to roughen a surface by blasting it with glass beads, then ions that were near grazing incidence (90 o ) on smooth surface would strike the rims of the micro-craters at angles closer to normal incidence. This should reduce the electron emission: the factor of 10 reduction, Fig. 1(a), implies an average angle of incidence of 62 o . Gas desorption varies more slowly with θ (Fig. 1(b)) decreasing a factor of ∼2, and along with the electron emission is independent of the angle of incidence on a rough surface. In a quadrupole magnet, electrons emitted by lost primary ions are trapped near the wall by the magnetic field, but grazing incidence ions can backscatter and strike the wall a second time at an azimuth where magnetic field lines intercept the beam. Then, electrons can exist throughout the beam (see the simulations of Cohen, HIF News 1-2/04). The SRIM (TRIM) Monte Carlo code predicts that 60-70% of 1 MeV K + ions backscatter when incident at 88-89 o from normal on a smooth surface. The scattered ions are mostly within ∼10 o of the initial direction but a few scatter by up to 90 o . Ion scattering decreases rapidly away from grazing incidence, Fig. 1(c ). At 62 deg. the predicted ion backscattering (from a rough surface) is 3%, down a factor of 20 from the peak, which should significantly reduce electrons in the beam from lost halo ions. These results are published in Phys. Rev. ST - Accelerators and Beams

  3. EM Bias-Correction for Ice Thickness and Surface Roughness Retrievals over Rough Deformed Sea Ice

    Science.gov (United States)

    Li, L.; Gaiser, P. W.; Allard, R.; Posey, P. G.; Hebert, D. A.; Richter-Menge, J.; Polashenski, C. M.

    2016-12-01

    The very rough ridge sea ice accounts for significant percentage of total ice areas and even larger percentage of total volume. The commonly used Radar altimeter surface detection techniques are empirical in nature and work well only over level/smooth sea ice. Rough sea ice surfaces can modify the return waveforms, resulting in significant Electromagnetic (EM) bias in the estimated surface elevations, and thus large errors in the ice thickness retrievals. To understand and quantify such sea ice surface roughness effects, a combined EM rough surface and volume scattering model was developed to simulate radar returns from the rough sea ice `layer cake' structure. A waveform matching technique was also developed to fit observed waveforms to a physically-based waveform model and subsequently correct the roughness induced EM bias in the estimated freeboard. This new EM Bias Corrected (EMBC) algorithm was able to better retrieve surface elevations and estimate the surface roughness parameter simultaneously. In situ data from multi-instrument airborne and ground campaigns were used to validate the ice thickness and surface roughness retrievals. For the surface roughness retrievals, we applied this EMBC algorithm to co-incident LiDAR/Radar measurements collected during a Cryosat-2 under-flight by the NASA IceBridge missions. Results show that not only does the waveform model fit very well to the measured radar waveform, but also the roughness parameters derived independently from the LiDAR and radar data agree very well for both level and deformed sea ice. For sea ice thickness retrievals, validation based on in-situ data from the coordinated CRREL/NRL field campaign demonstrates that the physically-based EMBC algorithm performs fundamentally better than the empirical algorithm over very rough deformed sea ice, suggesting that sea ice surface roughness effects can be modeled and corrected based solely on the radar return waveforms.

  4. Determining the surface roughness coefficient by 3D Scanner

    Directory of Open Access Journals (Sweden)

    Karmen Fifer Bizjak

    2010-12-01

    Full Text Available Currently, several test methods can be used in the laboratory to determine the roughness of rock joint surfaces.However, true roughness can be distorted and underestimated by the differences in the sampling interval of themeasurement methods. Thus, these measurement methods produce a dead zone and distorted roughness profiles.In this paper a new rock joint surface roughness measurement method is presented, with the use of a camera-typethree-dimensional (3D scanner as an alternative to current methods. For this study, the surfaces of ten samples oftuff were digitized by means of a 3D scanner, and the results were compared with the corresponding Rock JointCoefficient (JRC values. Up until now such 3D scanner have been mostly used in the automotive industry, whereastheir use for comparison with obtained JRC coefficient values in rock mechanics is presented here for the first time.The proposed new method is a faster, more precise and more accurate than other existing test methods, and is apromising technique for use in this area of study in the future.

  5. Influence of surface roughness of a desert

    Science.gov (United States)

    Sud, Y. C.; Smith, W. E.

    1984-01-01

    A numerical simulation study, using the current GLAS climate GCM, was carried out to examine the influence of low bulk aerodynamic drag parameter in the deserts. The results illustrate the importance of yet another feedback effect of a desert on itself, that is produced by the reduction in surface roughness height of land once the vegetation dies and desert forms. Apart from affecting the moisture convergence, low bulk transport coefficients of a desert lead to enhanced longwave cooling and sinking which together reduce precipitation by Charney's (1975) mechanism. Thus, this effect, together with albedo and soil moisture influence, perpetuate a desert condition through its geophysical feedback effect. The study further suggests that man made deserts is a viable hypothesis.

  6. Incorporating Skew into RMS Surface Roughness Probability Distribution

    Science.gov (United States)

    Stahl, Mark T.; Stahl, H. Philip.

    2013-01-01

    The standard treatment of RMS surface roughness data is the application of a Gaussian probability distribution. This handling of surface roughness ignores the skew present in the surface and overestimates the most probable RMS of the surface, the mode. Using experimental data we confirm the Gaussian distribution overestimates the mode and application of an asymmetric distribution provides a better fit. Implementing the proposed asymmetric distribution into the optical manufacturing process would reduce the polishing time required to meet surface roughness specifications.

  7. Internal surface roughness of plastic pipes for irrigation

    Directory of Open Access Journals (Sweden)

    Hermes S. da Rocha

    Full Text Available ABSTRACT Assuming that a roughness meter can be successfully employed to measure the roughness on the internal surface of irrigation pipes, this research had the purpose of defining parameters and procedures required to represent the internal surface roughness of plastic pipes used in irrigation. In 2013, the roughness parameter Ra, traditional for the representation of surface irregularities in most situations, and the parameters Rc, Rq, and Ry were estimated based on 350 samples of polyvinyl chloride (PVC and low-density polyethylene (LDPE pipes. Pressure losses were determined from experiments carried out in laboratory. Estimations of pressure loss varied significantly according to the roughness parameters (Ra, Rc, Rq, and Ry and the corresponding pipe diameter. Therefore, specific values of roughness for each pipe diameter improves accuracy in pressure losses estimation. The average values of internal surface roughness were 3.334 and 8.116 μm for PVC and LDPE pipes, respectively.

  8. Surface roughness analysis of electrodeposited Cu

    International Nuclear Information System (INIS)

    Lafouresse, M.C.; Heard, P.J.; Schwarzacher, W.

    2007-01-01

    Cu films were electrodeposited with mass transport controlled using a rotating disc electrode (RDE), and imaged with an atomic force microscope (AFM). The length-dependent roughness w(l,t) of these films follows a power law of the form w∝l H t β loc for small length-scales l, with the local roughness exponent, β loc , varying from 0 to 0.5 depending on the experimental conditions. It was found that contrary to previous work β loc is not simply a function of the ratio of the current j to its diffusion-limited value j L . Focused ion beam (FIB) imaging was used as a new method of characterizing the film roughness. FIB images confirmed the existence of small β loc values for films for which the AFM data could have been unreliable. FIB is a particularly powerful method for characterizing high roughness films

  9. Investigation of surface roughness on etched glass surfaces

    International Nuclear Information System (INIS)

    Papa, Z.; Budai, J.; Farkas, B.; Toth, Z.

    2011-01-01

    Roughening the surface of solar cells is a common practice within the photovoltaic industry as it reduces reflectance, and thus enhances the performance of devices. In this work the relationship between reflectance characterized by the haze parameter, surface roughness and optical properties was investigated. To achieve this goal, model samples were prepared by hydrofluoric acid etching of glass for various times and measured by optical microscopy, spectroscopic ellipsometry, scanning electron microscopy, and atomic force microscopy. Our investigation showed that the surface reflectance was decreased not only by the roughening of the surface but also by the modification of the depth profile and lowering of the refractive index of the surface domain of the samples.

  10. Surface Roughness and Residual Stresses of High Speed Turning 300 M Ultrahigh Strength Steel

    Directory of Open Access Journals (Sweden)

    Zhang Huiping

    2014-03-01

    Full Text Available Firstly, a single factor test of the surface roughness about tuning 300 M steel is done. According to the test results, it is direct to find the sequence of various factors affecting the surface roughness. Secondly, the orthogonal cutting experiment is carried out from which the primary and secondary influence factors affecting surface roughness are obtained: feed rate and corner radius are the main factors affecting surface roughness. The more the feed rate, the greater the surface roughness. In a certain cutting speed rang, the surface roughness is smaller. The influence of depth of cut to the surface roughness is small. Thirdly, according to the results of the orthogonal experiment, the prediction model of surface roughness is established by using regressing analysis method. Using MatLab software, the prediction mode is optimized and the significance test of the optimized model is done. It showed that the prediction model matched the experiment results. Finally, the surface residual stress test of turning 300 M steel is done and the residual stress of the surface and along the depth direction is measured.

  11. Investigation of surface roughness influence on hyperbolic metamaterial performance

    Directory of Open Access Journals (Sweden)

    S. Kozik

    2014-12-01

    Full Text Available The main goal of this work was to introduce simple model of surface roughness which does not involve objects with complicated shapes and could help to reduce computational costs. We described and proved numerically that the influence of surface roughness at the interfaces in metal-dielectric composite materials could be described by proper selection of refractive index of dielectric layers. Our calculations show that this model works for roughness with RMS value about 1 nm and below.

  12. Experimental investigation of turbulent flow-roughness interaction over surfaces of rigid and flexible roughness

    Science.gov (United States)

    Toloui, Mostafa; Hong, Jiarong

    2017-11-01

    The influence of flexible surface roughness on wall-bounded turbulent flows is examined experimentally via simultaneous 3D fluid velocity and roughness deformation measurements using Digital inline holographic PTV (i.e. DIH-PTV, Toloui et al. Meas. Sci. & Tech 2017). The experiments are conducted in a refractive-index-matched turbulent channel over two rough surface panels of similar geometry but with an order of magnitude difference in elastic modulus (1.8 Mpa vs. 0.2 Mpa). The roughness elements (i.e. tapered cylinders of 0.35 mm in base diameter, 3 mm in height, 4 mm spacing) are designed such that the rough surface with higher modulus shows no deformation (namely rigid roughness) while the one with lower elasticity deforms appreciably under the same flow conditions (Reh 32500 , based on centerline velocity and channel width). The concurrent fluid velocity and roughness deformation measurements are acquired with 160 μs temporal, 1.1 mm/vector velocity, and linked to roughness deformation. The fingerprint of this energy exchange on shortening the instantaneous flow structures, reduction of Reynolds stresses as well as flow features in energy spectra are examined and will be presented in detail.

  13. Influence of surface roughness on the corrosion behaviour of magnesium alloy

    International Nuclear Information System (INIS)

    Walter, R.; Kannan, M. Bobby

    2011-01-01

    Research highlights: → Surface roughness of AZ91 magnesium alloy plays a critical role in the passivation behaviour of the alloy. → The passivation behaviour of the alloy influences the pitting tendency. → Increase in surface roughness of AZ91 magnesium alloy increases the pitting tendency of the alloy. -- Abstract: In this study, the influence of surface roughness on the passivation and pitting corrosion behaviour of AZ91 magnesium alloy in chloride-containing environment was examined using electrochemical techniques. Potentiodynamic polarisation and electrochemical impedance spectroscopy tests suggested that the passivation behaviour of the alloy was affected by increasing the surface roughness. Consequently, the corrosion current and the pitting tendency of the alloy also increased with increase in the surface roughness. Scanning electron micrographs of 24 h immersion test samples clearly revealed pitting corrosion in the highest surface roughness (Sa 430) alloy, whereas in the lowest surface roughness (Sa 80) alloy no evidence of pitting corrosion was observed. Interestingly, when the passivity of the alloy was disturbed by galvanostatically holding the sample at anodic current for 1 h, the alloy underwent high pitting corrosion irrespective of their surface roughness. Thus the study suggests that the surface roughness plays a critical role in the passivation behaviour of the alloy and hence the pitting tendency.

  14. Finite Element Modeling of RMS Roughness Effect on the Contact Stiffness of Rough Surfaces

    Directory of Open Access Journals (Sweden)

    M.B. Amor

    2016-09-01

    Full Text Available The present study considers finite element analysis of an elastic and elastic-plastic contact between a rigid flat and a real rough surface taking into account the asperities interaction. Numerical modeling and measurement of the normal interfacial stiffness were conducted. Surfaces with different rms roughness values were investigated in the elastic and power-law hardening models to highlight the combined effect of the topography and the strain hardening on the contact characteristics. The influence of the surface roughness on the interaction between neighboring micro-contacts, the residual stress and deformation for the power-law hardening material was analyzed. The obtained results have shown the importance of considering the strain hardening in the modeling of a rough contact especially for rougher surface.

  15. Empirical model for estimating the surface roughness of machined ...

    African Journals Online (AJOL)

    Michael Horsfall

    Regression Analysis to construct a prediction model for surface roughness such that once the process parameters (cutting speed, feed, depth of cut, Nose. Radius and Speed) are given, the surface roughness can be predicted. The work piece material was EN8 which was processed by carbide-inserted tool conducted on ...

  16. Surface roughness and maintenance of surface sealants for resin composites after toothbrushing.

    Science.gov (United States)

    Bonato, Fernanda; Spohr, Ana Maria; Mota, Eduardo Gonçalves; Rodrigues-Junior, Sinval Adalberto; Burnett, Luiz Henrique

    2016-02-01

    (1) To evaluate in vitro the surface roughness of a resin composite covered with three surface sealants and submitted to simulated toothbrushing for different periods; (2) Verify, through scanning electron microscopy (SEM), the presence of surface sealants after simulated toothbrushing; and (3) To evaluate whether the type of dentifrice influences the maintenance of the surface sealant. The study hypothesis was that neither variable would influence the surface roughness of the composite and the maintenance of the surface sealant. 108 specimens were prepared with the resin Amelogen Plus, and divided into six groups (n = 18) according to the type of surface sealant [Fortify (F), BisCover LV (B) and Permaseal (P)] and toothpaste [Total 12 Clean Mint (CT) and Colgate Total 12 Professional Whitening (PW)]. The samples were subjected to brushing cycles, simulating periods of 6, 12, 18, and 24 months. After each period, the surface roughness of the samples was measured. An additional group of 48 samples was prepared for SEM analysis. The results were analyzed by ANOVA with three fixed variables (sealants, time and toothpaste) and by Tukey's test (α = 0.05). BisCover had the lowest mean surface roughness (0.06 µm) compared with the sealants Fortify (0.09 µm) and Permaseal (0.08 µm), which were not statistically different. Fortify, at 12 months of brushing, had the highest mean roughness (0.13 µm). The mean roughness for the dentifrice CT was lower (0.07 µm) when compared with PW (0.08 µm) and was statistically different. Roughness increased up to 12 months of simulated brushing (0.04 µm, 0.08 µm and 0.11 µm), decreasing from the 18th month (0.08 µm) to the 24th month of brushing (0.07 µm). None of the sealants was observed (with SEM) to be completely removed from the resin at 24 months of brushing.

  17. Influence of starting material particle size on pellet surface roughness.

    Science.gov (United States)

    Sarkar, Srimanta; Ang, Bee Hwee; Liew, Celine Valeria

    2014-02-01

    The purpose of this study was to investigate the effect of pelletization aids, i.e., microcrystalline cellulose (MCC) and cross-linked polyvinyl pyrrolidone (XPVP), and filler, i.e., lactose, particle size on the surface roughness of pellets. Pellets were prepared from powder blends containing pelletization aid/lactose in 1:3 ratio by extrusion-spheronization. Surface roughness of pellets was assessed quantitatively and qualitatively using optical interferometry and scanning electron microscopy, respectively. Both quantitative and qualitative surface studies showed that surface roughness of pellets depended on the particle size of XPVP and lactose used in the formulation. Increase in XPVP or lactose particle size resulted in rougher pellets. Formulations containing MCC produced pellets with smoother surfaces than those containing XPVP. Furthermore, surface roughness of the resultant pellets did not appear to depend on MCC particle size. Starting material particle size was found to be a critical factor for determining the surface roughness of pellets produced by extrusion-spheronization. Smaller particles can pack well with lower peaks and valleys, resulting in pellets with smoother surfaces. Similar surface roughness of pellets containing different MCC grades could be due to the deaggregation of MCC particles into smaller subunits with more or less similar sizes during wet processing. Hence, for starting materials that deaggregate during the wet processing, pellet surface roughness is influenced by the particle size of the material upon deaggregation.

  18. Characterizing developing adverse pressure gradient flows subject to surface roughness

    Science.gov (United States)

    Brzek, Brian; Chao, Donald; Turan, Özden; Castillo, Luciano

    2010-04-01

    An experimental study was conducted to examine the effects of surface roughness and adverse pressure gradient (APG) on the development of a turbulent boundary layer. Hot-wire anemometry measurements were carried out using single and X-wire probes in all regions of a developing APG flow in an open return wind tunnel test section. The same experimental conditions (i.e., T ∞, U ref, and C p) were maintained for smooth, k + = 0, and rough, k + = 41-60, surfaces with Reynolds number based on momentum thickness, 3,000 carefully designed such that the x-dependence in the flow field was known. Despite this fact, only a very small region of the boundary layer showed a balance of the various terms in the integrated boundary layer equation. The skin friction computed from this technique showed up to a 58% increase due to the surface roughness. Various equilibrium parameters were studied and the effect of roughness was investigated. The generated flow was not in equilibrium according to the Clauser (J Aero Sci 21:91-108, 1954) definition due to its developing nature. After a development region, the flow reached the equilibrium condition as defined by Castillo and George (2001), where Λ = const, is the pressure gradient parameter. Moreover, it was found that this equilibrium condition can be used to classify developing APG flows. Furthermore, the Zagarola and Smits (J Fluid Mech 373:33-79, 1998a) scaling of the mean velocity deficit, U ∞δ*/δ, can also be used as a criteria to classify developing APG flows which supports the equilibrium condition of Castillo and George (2001). With this information a ‘full APG region’ was defined.

  19. Surface areas of fractally rough particles studied by scattering

    International Nuclear Information System (INIS)

    Hurd, A.J.; Schaefer, D.W.; Smith, D.M.; Ross, S.B.; Le Mehaute, A.; Spooner, S.

    1989-01-01

    The small-angle scattering from fractally rough surfaces has the potential to give information on the surface area at a given resolution. By use of quantitative neutron and x-ray scattering, a direct comparison of surface areas of fractally rough powders was made between scattering and adsorption techniques. This study supports a recently proposed correction to the theory for scattering from fractal surfaces. In addition, the scattering data provide an independent calibration of molecular adsorbate areas

  20. Determining Surface Roughness in Urban Areas Using Lidar Data

    Science.gov (United States)

    Holland, Donald

    2009-01-01

    An automated procedure has been developed to derive relevant factors, which can increase the ability to produce objective, repeatable methods for determining aerodynamic surface roughness. Aerodynamic surface roughness is used for many applications, like atmospheric dispersive models and wind-damage models. For this technique, existing lidar data was used that was originally collected for terrain analysis, and demonstrated that surface roughness values can be automatically derived, and then subsequently utilized in disaster-management and homeland security models. The developed lidar-processing algorithm effectively distinguishes buildings from trees and characterizes their size, density, orientation, and spacing (see figure); all of these variables are parameters that are required to calculate the estimated surface roughness for a specified area. By using this algorithm, aerodynamic surface roughness values in urban areas can then be extracted automatically. The user can also adjust the algorithm for local conditions and lidar characteristics, like summer/winter vegetation and dense/sparse lidar point spacing. Additionally, the user can also survey variations in surface roughness that occurs due to wind direction; for example, during a hurricane, when wind direction can change dramatically, this variable can be extremely significant. In its current state, the algorithm calculates an estimated surface roughness for a square kilometer area; techniques using the lidar data to calculate the surface roughness for a point, whereby only roughness elements that are upstream from the point of interest are used and the wind direction is a vital concern, are being investigated. This technological advancement will improve the reliability and accuracy of models that use and incorporate surface roughness.

  1. Surface roughness effects on the hypersonic turbulent boundary layer

    Energy Technology Data Exchange (ETDEWEB)

    Berg, D.E.

    1977-09-01

    An experimental investigation of the response of a hypersonic turbulent boundary layer to a step change in surface roughness has been performed. The boundary layer on a flat nozzle wall of a Mach 6 wind tunnel was subjected to abrupt changes in surface roughness and its adjustment to the new surface conditions was examined. Both mean and fluctuating flow properties were acquired for smooth-to-rough and rough-to-smooth surface configurations. The boundary layer was found to respond gradually and to attain new equilibrium profiles, for both the mean and the fluctuating properties, some 10 to 25 delta downstream of the step change. Mean flow self-similarity was the first to establish itself, followed by the mass flux fluctuations, followed in turn by the total temperature fluctuations. Use of a modified Van Driest transformation resulted in good correlations of smooth and rough wall data in the form of the incompressible law of the wall. This is true even in the nonequilibrium vicinity of the step for small roughness heights. The present data are found to correlate well with previously published roughness effect data from low and high speed flows when the roughnesses are characterized by an equivalent sand grain roughness height.

  2. Surface Roughness of Composite Panels as a Quality Control Tool

    Directory of Open Access Journals (Sweden)

    Onur Ulker

    2018-03-01

    Full Text Available This paper describes a study of the quantify surface roughness of experimentally manufactured particleboards and sandwiched panels having fibers on the surface layers. Surface quality of specimens before and after being overlaid with thin melamine impregnated papers was determined by employing profilometer equipment. Roughness measurements and Janka hardness were carried out on the specimens conditioned at 60% and 95% relative humidity levels. Based on the findings in this work, surface roughness of the specimens that were exposed two relative humidity exposure showed significant differences from each others. Data determined in this study could be beneficial to understand behavior of such panels exposed different humidity levels.

  3. Effect of various tooth whitening modalities on microhardness, surface roughness and surface morphology of the enamel.

    Science.gov (United States)

    Kwon, So Ran; Kurti, Steven R; Oyoyo, Udochukwu; Li, Yiming

    2015-09-01

    The purpose of this study was to evaluate the effect of four whitening modalities on surface enamel as assessed with microhardness tester, profilometer, and scanning electron microscopy (SEM). Whitening was performed according to manufacturer's directions for over-the-counter (OTC), dentist dispensed for home use (HW) and in-office (OW) whitening. Do-it-yourself (DIY) whitening consisted of a strawberry and baking soda mix. Additionally, negative and positive controls were used. A total of 120 enamel specimens were used for microhardness testing at baseline and post-whitening. Following microhardness testing specimens were prepared for SEM observations. A total of 120 enamel specimens were used for surface roughness testing at baseline and post-whitening (n = 20 per group). Rank-based Analysis of Covariance was performed to compare microhardness and surface roughness changes. Tests of hypotheses were two-sided with α = 0.05. There was a significant difference in Knoop hardness changes (ΔKHN) among the groups (Kruskal-Wallis test, p < 0.0001). Significant hardness reduction was observed in the positive control and DIY group (p < 0.0001). Mean surface roughness changes (ΔRa) were significantly different among the groups (Kruskal-Wallis test, p < 0.0001). Surface roughness increased in the OTC group (p = 0.03) and in the positive control (p < 0.0001). The four whitening modalities-DIY, OTC, HW and OW induced minimal surface morphology changes when observed with SEM. It can be concluded that none of the four whitening modalities adversely affected enamel surface morphology. However, caution should be advised when using a DIY regimen as it may affect enamel microhardness and an OTC product as it has the potential to increase surface roughness.

  4. Polished Stone Value Test and its relationship with petrographic parameters (hardness contrast and modal composition and surface micro-roughness in natural and artificial aggregates

    Directory of Open Access Journals (Sweden)

    Fernández, A.

    2013-09-01

    Full Text Available The goal of this work was first to establish the relationships between the PSV values and the microstructural and mineralogical features of the aggregates and surface micro-roughness, and then to establish the behavioural differences between natural and artificial aggregates. The results obtained indicate that the surface micro-roughness and the different PSV values of the natural aggregates are strongly governed by the existence of minerals with different degrees of hardness, together with the proportion of these minerals. In contrast, the different degree of porosity in artificial aggregates (a furnace slag was seen to be responsible for its high surface micro-roughness and PSV values. Finally, the PSV and a petrographic parameter (Overall Hardness Contrast, ΔH were seen to be related by an exponential curve (PSV=39.726ΔH0.057 with an extremely good fit, providing a good tool to estimate PSVs in natural and artificial aggregates from petrographic parameters.El objetivo de este trabajo es establecer, por un lado, las relaciones existentes del CPA con las características petrográficas de los áridos, así como su microrrugosidad superficial y, por otro, las diferencias de comportamiento entre áridos naturales y artificiales. Los resultados indican que en los áridos naturales la microrrugosidad superficial y el diferente valor del CPA están determinados, en gran medida, por las diferencias de dureza de sus minerales y también por la proporción en la que estos minerales se encuentran en las distintas litologías. Sin embargo, en los áridos artificiales (escorias de fundición su elevada porosidad es la responsable de su marcada microrrugosidad superficial y su elevado valor del CPA. Finalmente, se relaciona el CPA con un parámetro petrográfico (Contraste de Dureza Global, ΔH mediante una curva exponencial, cuyo excelente índice de regresión hace que sea factible estimar mediante el estudio petrográfico de un árido su valor del CPA

  5. Roughness-Based Superhydrophobic Surfaces: Fundamentals and Future Directions

    Science.gov (United States)

    Patankar, Neelesh

    2011-11-01

    Superhydrophobicity of rough surfaces has attracted global interest through the past decade. There are naturally occurring instances of such surfaces, e.g., lotus leaves, which led to the popular term ``lotus effect.'' Numerous applications in wide ranging areas such as drag reduction, self-cleaning, heat exchangers, energy conversion, condensation, anti-icing, textile, desalination, etc., are being explored by researchers worldwide. The signature configuration for superhydrophobicity has been ``bead-like'' drops on rough surfaces that roll-off easily. This becomes possible if the liquid does not impale the roughness grooves, and if the contact angle hysteresis is low. Finding appropriate surface roughness is therefore necessary. A thermodynamic framework to enable analysis of this problem will be presented. It will be noted that the success of rough superhydrophobic substrates relies on the presence of gas pockets in the roughness grooves underneath the liquid. These gas pockets could be those of air from the surrounding environment. Current design strategies rely on the availability of air. However, if the rough substrates are fully submerged in the liquid then the trapped air in the roughness grooves may not be sustained. A design approach based on sustaining a vapor phase of the liquid itself in the roughness grooves, instead of relying on the presence of air, will be presented. The resulting surfaces, referred to as vapor stabilizing substrates, are deemed to be robust against wetting transition even if no air is present. Applications of this approach include low drag surfaces, nucleate boiling at dramatically low superheats, among others. The concept can be generalized to other transitions on the phase diagram, thus enabling the design of rough surfaces for phase manipulation in general.

  6. Estimating aerodynamic resistance of rough surfaces from angular reflectance

    Science.gov (United States)

    Current wind erosion and dust emission models neglect the heterogeneous nature of surface roughness and its geometric anisotropic effect on aerodynamic resistance, and over-estimate the erodible area by assuming it is not covered by roughness elements. We address these shortfalls with a new model wh...

  7. Reducing surface roughness by optimising the turning parameters

    Directory of Open Access Journals (Sweden)

    Senthil Kumar, K.

    2013-08-01

    Full Text Available Modern manufacturers worldwide look for the cheapest quality-manufactured machined components to compete in the market. Good surface quality is desired for the proper functioning of the parts produced. The surface quality is influenced by the cutting speed, feed rate, depth of cut, and many other parameters. In this paper, the Taguchi method a powerful tool to design optimisation for quality is used to find the optimal machining parameters for the turning operation. An orthogonal array, the signal-to-noise (S/N ratio, and the analysis of variance (ANOVA are employed to investigate the machining characteristics of super duplex stainless steel bars using uncoated carbide cutting tools. The effect of machining parameters on surface roughness was discovered. Confirmation tests were conducted at optimal conditions to compare the experimental results with the predicted values.

  8. Simple model of surface roughness for binary collision sputtering simulations

    International Nuclear Information System (INIS)

    Lindsey, Sloan J.; Hobler, Gerhard; Maciążek, Dawid; Postawa, Zbigniew

    2017-01-01

    Highlights: • A simple model of surface roughness is proposed. • Its key feature is a linearly varying target density at the surface. • The model can be used in 1D/2D/3D Monte Carlo binary collision simulations. • The model fits well experimental glancing incidence sputtering yield data. - Abstract: It has been shown that surface roughness can strongly influence the sputtering yield – especially at glancing incidence angles where the inclusion of surface roughness leads to an increase in sputtering yields. In this work, we propose a simple one-parameter model (the “density gradient model”) which imitates surface roughness effects. In the model, the target’s atomic density is assumed to vary linearly between the actual material density and zero. The layer width is the sole model parameter. The model has been implemented in the binary collision simulator IMSIL and has been evaluated against various geometric surface models for 5 keV Ga ions impinging an amorphous Si target. To aid the construction of a realistic rough surface topography, we have performed MD simulations of sequential 5 keV Ga impacts on an initially crystalline Si target. We show that our new model effectively reproduces the sputtering yield, with only minor variations in the energy and angular distributions of sputtered particles. The success of the density gradient model is attributed to a reduction of the reflection coefficient – leading to increased sputtering yields, similar in effect to surface roughness.

  9. Evaluation of surface roughness of the bracket slot floor—a 3D perspective study

    Directory of Open Access Journals (Sweden)

    Chetankumar O. Agarwal

    2016-01-01

    Full Text Available Abstract Background An important constituent of an orthodontic appliance is orthodontic brackets. It is either the bracket or the archwire that slides through the bracket slot, during sliding mechanics. Overcoming the friction between the two surfaces demands an important consideration in an appliance design. The present study investigated the surface roughness of four different commercially available stainless steel brackets. Methods All tests were carried out to analyse quantitatively the morphological surface of the bracket slot floor with the help of scanning electron microscope (SEM machine and to qualitatively analyse the average surface roughness (Sa of the bracket slot floor with the help of a three-dimensional (3D non-contact optical surface profilometer machine. Results The SEM microphotographs were evaluated with the help of visual analogue scale, the surface roughness for group A = 0—very rough surface, group C = 1—rough surface, group B = 2—smooth surface, and group D = 3—very smooth surface. Surface roughness evaluation with the 3D non-contact optical surface profilometer machine was highest for group A, followed by group C, group B and group D. Groups B and D provided smooth surface roughness; however, group D had the very smooth surface with values 0.74 and 0.75 for mesial and distal slots, respectively. Conclusions Evaluation of surface roughness of the bracket slot floor with both SEM and profilometer machine led to the conclusion that the average surface roughness was highest for group A, followed by group C, group B and group D.

  10. Temporal and Spectral Coherence From Rough Surface Scattering

    National Research Council Canada - National Science Library

    Gu, Zu-Han

    2006-01-01

    .... The enhanced backscattering is manifested by the presence of a well-defined peak in the retro-reflection direction in the angular distribution of the intensity of the diffusely scattered light from a rough surface...

  11. SMAPVEX12 Surface Roughness Data for Agricultural Area V001

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set contains surface roughness data collected at several agricultural sites as a part of the Soil Moisture Active Passive Validation Experiment 2012...

  12. Ice friction: The effects of surface roughness, structure, and hydrophobicity

    Science.gov (United States)

    Kietzig, Anne-Marie; Hatzikiriakos, Savvas G.; Englezos, Peter

    2009-07-01

    The effect of surface roughness, structure, and hydrophobicity on ice friction is studied systematically over a wide range of temperature and sliding speeds using several metallic interfaces. Hydrophobicity in combination with controlled roughness at the nanoscale is achieved by femtosecond laser irradiation to mimic the lotus effect on the slider's surface. The controlled roughness significantly increases the coefficient of friction at low sliding speeds and temperatures well below the ice melting point. However, at temperatures close to the melting point and relatively higher speeds, roughness and hydrophobicity significantly decrease ice friction. This decrease in friction is mainly due to the suppression of capillary bridges in spite of the presence of surface asperities that facilitate their formation. Finally, grooves oriented in the sliding direction also significantly decrease friction in the low velocity range compared to scratches and grooves randomly distributed over a surface.

  13. Surface Roughness Measurement on a Wing Aircraft by Speckle Correlation

    Directory of Open Access Journals (Sweden)

    Alberto Barrientos

    2013-09-01

    Full Text Available The study of the damage of aeronautical materials is important because it may change the microscopic surface structure profiles. The modification of geometrical surface properties can cause small instabilities and then a displacement of the boundary layer. One of the irregularities we can often find is surface roughness. Due to an increase of roughness and other effects, there may be extra momentum losses in the boundary layer and a modification in the parasite drag. In this paper we present a speckle method for measuring the surface roughness on an actual unmanned aircraft wing. The results show an inhomogeneous roughness distribution on the wing, as expected according to the anisotropic influence of the winds over the entire wing geometry. A calculation of the uncertainty of the technique is given.

  14. Surface roughness measurement on a wing aircraft by speckle correlation.

    Science.gov (United States)

    Salazar, Félix; Barrientos, Alberto

    2013-09-05

    The study of the damage of aeronautical materials is important because it may change the microscopic surface structure profiles. The modification of geometrical surface properties can cause small instabilities and then a displacement of the boundary layer. One of the irregularities we can often find is surface roughness. Due to an increase of roughness and other effects, there may be extra momentum losses in the boundary layer and a modification in the parasite drag. In this paper we present a speckle method for measuring the surface roughness on an actual unmanned aircraft wing. The results show an inhomogeneous roughness distribution on the wing, as expected according to the anisotropic influence of the winds over the entire wing geometry. A calculation of the uncertainty of the technique is given.

  15. Roughness of the globular protein surface

    International Nuclear Information System (INIS)

    Timchenko, A.A.; Galzitskaya, O.V.; Serdyuk, I.N.

    1998-01-01

    Protein surface analysis using high resolution X ray shows that this surface has a two-level organization, on the micro- and macro-scales. On the micro-scale (2-7 Angstroem), the surface is characterized by the d = 2.1 fractal dimension which is intrinsic to surface with weak deformation and reflects the local atomic group packing. On the macro-scale the large scale surface defects are revealed which are interpreted as the result of secondary structure elements packing

  16. Surface roughness influences on the behaviour of flow inside microchannels

    Science.gov (United States)

    Farias, M. H.; Castro, C. S.; Garcia, D. A.; Henrique, J. S.

    2018-03-01

    This work discusses influence of the surface roughness on the behavior of liquids flowing inside microchannels. By measuring the flow profile using the micro-PIV technique, the flow of water inside two rectangular microchannels of different wall roughness and in a circular smooth microchannel was studied. Comparisons were made among the experimental results, showing that a metrological approach concerning surface characteristics of microdevices is required to ensure reliability of the measurements for flow analyses in microfluidic processes.

  17. Effect of surface roughness on ultrasonic echo amplitude in aluminium-copper alloy castings

    International Nuclear Information System (INIS)

    Ambardar, R.; Pathak, S.D.; Prabhakar, O.; Jayakumar, T.

    1996-01-01

    In the present investigation, the influence of test surface roughness on ultrasonic back-wall echo (BWE) amplitude in Al-4.5%Cu alloy cast specimens has been studied. The results indicate that as the value of surface roughness of the specimen increases, the value of relating BWE amplitude at a given probe frequency decreases. However, under the present set of experimental conditions, the decrease in BWE amplitude with the increase in surface roughness of the test specimen is found to be appreciable at 10 MHz probe frequency. (author)

  18. Importance of thermal effects and sea surface roughness for offshore wind resource assessment

    DEFF Research Database (Denmark)

    Lange, B.; Larsen, Søren Ejling; Højstrup, Jørgen

    2004-01-01

    -Obukhov theory, a simple correction method to account for this effect has been developed and is tested in the same way. The models for the estimation of the sea surface roughness were found to lead only to small differences. For the purpose of wind resource assessment, even the assumption of a constant roughness...

  19. Turbulent lubrication theory considering the surface roughness effects, 2

    International Nuclear Information System (INIS)

    Hashimoto, Hiromu; Wada, Sanae; Kobayashi, Toshinobu.

    1990-01-01

    This second paper describes an application of the generalized turbulent lubrication theory considering the surface roughness effects, which is developed in the previous paper, to the finite-width journal bearings. In the numerical analysis, the nonlinear equations for the modified turbulence coefficients are simplified to save a computation time within a satisfactory accuracy under the assumption that the shear flow is superior to the pressure flow in the turbulent lubrication films. The numerical results of pressure distribution, Sommerfeld number, attitude angle, friction coefficient and flow rate for the Reynolds number of Re=2000, 5000 and 10000 are indicated in graphic form for various values of relative roughness, and the effects of surface roughness on these static performance characteristics are discussed. Moreover, the eccentricity ratio and attitude angle of the journal bearings with homogeneous rough surface are obtained experimentally for a wide range of Sommerfeld number, and the experimental results are compared with theoretical results. (author)

  20. The effect of surface roughness of glass on the leachability

    International Nuclear Information System (INIS)

    Yamanaka, Hiroshi; Terai, Ryohei; Hara, Shigeo

    1982-01-01

    The effect of surface roughness of glass samples on the leachability of simulated high-level nuclear waste containing borosilicate glasses has been investigated from view-point of safety evaluation, using the Soxhlet-type leaching apparatus. The quantity extracted from glasses had generally increased with increasing of the surface roughness of glass block samples. SEM photographs demonstrated that the surface abraded by coarse abrasive powder has had many unevennesses and cracks which brought about an accelerated attack on glass surface. It seems, therefore, that the surface roughness of specimens should be defined as a criterion of leachability. The reaction between glass and water brought about the formation of hydrated layer more easily on the borosilicate glass than on the soda-lime silicate glass. The resultant hydrated layer produces many cracks by drying, but the cracks can not be observed by naked eye. Therefore, the observation by SEM is necessary for precise evaluation on the corroded surface of glasses. (author)

  1. Identification of vehicles moving on continuous bridges with rough surface

    Science.gov (United States)

    Jiang, R. J.; Au, F. T. K.; Cheung, Y. K.

    2004-07-01

    This paper describes the parameter identification of vehicles moving on multi-span continuous bridges taking into account the surface roughness. Each moving vehicle is modelled as a two-degree-of-freedom system that comprises five components: a lower mass and an upper mass, which are connected together by a damper and a spring, together with another spring to represent the contact stiffness between the tyres and the bridge deck. The corresponding parameters of these five components, namely, the equivalent values of the two masses, the damping coefficient, and the two spring stiffnesses together with the roughness parameters are identified based on dynamic simulation of the vehicle-bridge system. In the study, the accelerations at selected measurement stations are simulated from the dynamic analysis of a continuous beam under moving vehicles taking into account randomly generated bridge surface roughness, together with the addition of artificially generated measurement noise. The identification is realized through a robust multi-stage optimization scheme based on genetic algorithms, which searches for the best estimates of parameters by minimizing the errors between the measured accelerations and the reconstructed accelerations from the identified parameters. Starting from the very wide initial variable domains, this multi-stage optimization scheme reduces the variable search domains stage by stage using the identified results of the previous stage. A few test cases are carried out to verify the efficiency of the multi-stage optimization procedure. The identified parameters are also used to estimate the time-varying contact forces between the vehicles and the bridge.

  2. Cheap and fast measuring roughness on big surfaces with an imprint method

    Science.gov (United States)

    Schopf, C.; Liebl, J.; Rascher, R.

    2017-10-01

    Roughness, shape and structure of a surface offer information on the state, shape and surface characteristics of a component. Particularly the roughness of the surface dictates the subsequent polishing of the optical surface. The roughness is usually measured by a white light interferometer, which is limited by the size of the components. Using a moulding method of surfaces that are difficult to reach, an imprint is taken and analysed regarding to roughness and structure. This moulding compound method is successfully used in dental technology. In optical production, the moulding compound method is advantageous in roughness determination in inaccessible spots or on large components (astrological optics). The "replica method" has been around in metal analysis and processing. Film is used in order to take an impression of a surface. Then, it is analysed for structures. In optical production, compound moulding seems advantageous in roughness determination in inaccessible spots or on large components (astrological optics). In preliminary trials, different glass samples with different roughness levels were manufactured. Imprints were taken from these samples (based on DIN 54150 "Abdruckverfahren für die Oberflächenprüfung"). The objective of these feasibility tests was to determine the limits of this method (smallest roughness determinable / highest roughness). The roughness of the imprint was compared with the roughness of the glass samples. By comparing the results, the uncertainty of the measuring method was determined. The spectrum for the trials ranged from rough grind (0.8 μm rms), over finishing grind (0.6 μm rms) to polishing (0.1 μm rms).

  3. Optimization of surface roughness in CNC end milling using ...

    African Journals Online (AJOL)

    Optimization of surface roughness in CNC end milling using response surface methodology and genetic algorithm. ... International Journal of Engineering, Science and Technology ... using RSM. The response surface (RS) model is interfaced with the genetic algorithm (GA) to find the optimum machining parameter values.

  4. Change of Surface Roughness and Planetary Boundary Layer

    DEFF Research Database (Denmark)

    Jensen, Niels Otto

    1978-01-01

    The ratio between upstream and far downstream surface friction velocities relative to a change in surface roughness is given on the basis of results from surface Rossby number similarity theory. By simple theories for the internal boundary layer, which are found to compare quite well with recent ...

  5. Roughness analysis of graphite surfaces of casting elements

    Directory of Open Access Journals (Sweden)

    M. Wieczorowski

    2010-01-01

    Full Text Available In the paper profilometric measurements of graphite casting elements were described. Basic topics necessary to assess roughness of their surfaces and influence of asperities on various properties related to manufacturing and use were discussed. Stylus profilometer technique of surface irregularities measurements including its limits resulting from pickup geometry and its contact with measured object were ana-lyzed. Working principle of tactile profilometer and phenomena taking place during movement of a probe on a measured surface were shown. One of the important aspects is a flight phenomenon, which means movement of a pickup without contact with a surface during inspection resulting from too high scanning speed. results of comparison research for graphite elements of new and used mould and pin composing a set were presented. Using some surface roughness, waviness and primary profile parameters (arithmetical mean of roughness profile heights Ra, biggest roughness profile height Rz, maximum primary profile height Pt as well as maximum waviness profile height Wt a possibility of using surface asperities parameters as a measure of wear of chill graphite elements was proved. The most often applied parameter is Ra, but with a help of parameters from W and P family it was shown, that big changes occur not only for roughness but also for other components of surface irregularities.

  6. Wetting Properties of Molecularly Rough Surfaces

    Czech Academy of Sciences Publication Activity Database

    Svoboda, Martin; Malijevský, Alexandr; Lísal, Martin

    2015-01-01

    Roč. 143, č. 10 (2015), s. 104701 ISSN 0021-9606 R&D Projects: GA ČR GA13-09914S; GA MŠk LH12020 Institutional support: RVO:67985858 Keywords : contant-angle * solid-surface * dynamics Subject RIV: BJ - Thermodynamics Impact factor: 2.894, year: 2015

  7. Comparison of optical methods for surface roughness characterization

    DEFF Research Database (Denmark)

    Feidenhans'l, Nikolaj Agentoft; Hansen, Poul Erik; Pilny, Lukas

    2015-01-01

    We report a study of the correlation between three optical methods for characterizing surface roughness: a laboratory scatterometer measuring the bi-directional reflection distribution function (BRDF instrument), a simple commercial scatterometer (rBRDF instrument), and a confocal optical profiler...... of the scattering angle distribution (Aq). The twenty-two investigated samples were manufactured with several methods in order to obtain a suitable diversity of roughness patterns.Our study shows a one-to-one correlation of both the Rq and the Rdq roughness values when obtained with the BRDF and the confocal...

  8. Simple model of surface roughness for binary collision sputtering simulations

    Science.gov (United States)

    Lindsey, Sloan J.; Hobler, Gerhard; Maciążek, Dawid; Postawa, Zbigniew

    2017-02-01

    It has been shown that surface roughness can strongly influence the sputtering yield - especially at glancing incidence angles where the inclusion of surface roughness leads to an increase in sputtering yields. In this work, we propose a simple one-parameter model (the "density gradient model") which imitates surface roughness effects. In the model, the target's atomic density is assumed to vary linearly between the actual material density and zero. The layer width is the sole model parameter. The model has been implemented in the binary collision simulator IMSIL and has been evaluated against various geometric surface models for 5 keV Ga ions impinging an amorphous Si target. To aid the construction of a realistic rough surface topography, we have performed MD simulations of sequential 5 keV Ga impacts on an initially crystalline Si target. We show that our new model effectively reproduces the sputtering yield, with only minor variations in the energy and angular distributions of sputtered particles. The success of the density gradient model is attributed to a reduction of the reflection coefficient - leading to increased sputtering yields, similar in effect to surface roughness.

  9. The Effect of Hydrogen Peroxide 35% on Surface Roughness of Silorane and Methacrylate Based Composites

    Directory of Open Access Journals (Sweden)

    L. Rezaei Sofi

    2015-04-01

    Full Text Available Introduction & Objectives: Surface roughness affects beauty, hygiene, plaque retention and health of the gingival adjacent to the composite restoration. Many people use bleaching agents to beautify their teeth that may lead to changes in surface roughness. This study was designed to compare the silorane and methacrylate-based composites in bleached teeth. Materials & Methods: In this experimental study 48 composite resin disks were prepared and divided into 4 groups: P90, Z250, Z250XT and Z350XT (n=12. To determine the surface roughness, surface profile measurement of the samples was performed using profilometer. Samples of each diet group underwent 35% hydrogen peroxide in office whitening (Hpmax in three 45-minute sessions one week apart. The secondary instances of surface profile was then measured. The data collected by the Kolmogorov-Smirnov test, one-way ANOVA, Tukey test and paired t- test at a significance level of 0.05 were analyzed using spss16. Results: There was a significant difference (P<0.05 in the surface roughness after bleaching on composite Z350XT with P90 and Z350XT with Z250. The surface roughness of all groups before and after bleaching showed a significant difference (P<0.05. Conclusion: The use of hydrogen peroxide 35% causes a significant increase in the surface roughness of composite P90, Z250, Z250XT and Z350XT. (Sci J Hamadan Univ Med Sci 2015; 22 (1:23-29

  10. Surface roughness reduction using spray-coated hydrogen silsesquioxane reflow

    DEFF Research Database (Denmark)

    Cech, Jiri; Pranov, Henrik; Kofod, Guggi

    2013-01-01

    Surface roughness or texture is the most visible property of any object, including injection molded plastic parts. Roughness of the injection molding (IM) tool cavity directly affects not only appearance and perception of quality, but often also the function of all manufactured plastic parts. So...... are reduced 10 and 3 times respectively. We completed more than 10,000 injection molding cycles without detectable degradation of the HSQ coating. This result opens new possibilities for molding of affordable plastic parts with perfect surface finish....... called “optically smooth” plastic surfaces is one example, where low roughness of a tool cavity is desirable. Such tool surfaces can be very expensive to fabricate using conventional means, such as abrasive diamond polishing or diamond turning. We present a novel process to coat machined metal parts...

  11. Response Ant Colony Optimization of End Milling Surface Roughness

    Directory of Open Access Journals (Sweden)

    Ahmed N. Abd Alla

    2010-03-01

    Full Text Available Metal cutting processes are important due to increased consumer demands for quality metal cutting related products (more precise tolerances and better product surface roughness that has driven the metal cutting industry to continuously improve quality control of metal cutting processes. This paper presents optimum surface roughness by using milling mould aluminium alloys (AA6061-T6 with Response Ant Colony Optimization (RACO. The approach is based on Response Surface Method (RSM and Ant Colony Optimization (ACO. The main objectives to find the optimized parameters and the most dominant variables (cutting speed, feedrate, axial depth and radial depth. The first order model indicates that the feedrate is the most significant factor affecting surface roughness.

  12. Multipoint contact modeling of nanoparticle manipulation on rough surface

    Energy Technology Data Exchange (ETDEWEB)

    Zakeri, M., E-mail: m.zakeri@tabrizu.ac.ir; Faraji, J.; Kharazmi, M. [University of Tabriz, School of Engineering Emerging Technologies (Iran, Islamic Republic of)

    2016-12-15

    In this paper, the atomic force microscopy (AFM)-based 2-D pushing of nano/microparticles investigated on rough substrate by assuming a multipoint contact model. First, a new contact model was extracted and presented based on the geometrical profiles of Rumpf, Rabinovich and George models and the contact mechanics theories of JKR and Schwartz, to model the adhesion forces and the deformations in the multipoint contact of rough surfaces. The geometry of a rough surface was defined by two main parameters of asperity height (size of roughness) and asperity wavelength (compactness of asperities distribution). Then, the dynamic behaviors of nano/microparticles with radiuses in range of 50–500 nm studied during their pushing on rough substrate with a hexagonal or square arrangement of asperities. Dynamic behavior of particles were simulated and compared by assuming multipoint and single-point contact schemes. The simulation results show that the assumption of multipoint contact has a considerable influence on determining the critical manipulation force. Additionally, the assumption of smooth surfaces or single-point contact leads to large error in the obtained results. According to the results of previous research, it anticipated that a particles with the radius less than about 550 nm start to slide on smooth substrate; but by using multipoint contact model, the predicted behavior changed, and particles with radii of smaller than 400 nm begin to slide on rough substrate for different height of asperities, at first.

  13. Fuzzy Linguistic Optimization on Surface Roughness for CNC Turning

    Directory of Open Access Journals (Sweden)

    Tian-Syung Lan

    2010-01-01

    Full Text Available Surface roughness is often considered the main purpose in contemporary computer numerical controlled (CNC machining industry. Most existing optimization researches for CNC finish turning were either accomplished within certain manufacturing circumstances or achieved through numerous equipment operations. Therefore, a general deduction optimization scheme is deemed to be necessary for the industry. In this paper, the cutting depth, feed rate, speed, and tool nose runoff with low, medium, and high level are considered to optimize the surface roughness for finish turning based on L9(34 orthogonal array. Additionally, nine fuzzy control rules using triangle membership function with respective to five linguistic grades for surface roughness are constructed. Considering four input and twenty output intervals, the defuzzification using center of gravity is then completed. Thus, the optimum general fuzzy linguistic parameters can then be received. The confirmation experiment result showed that the surface roughness from the fuzzy linguistic optimization parameters is significantly advanced compared to that from the benchmark. This paper certainly proposes a general optimization scheme using orthogonal array fuzzy linguistic approach to the surface roughness for CNC turning with profound insight.

  14. Optimization of surface roughness in turning of GFRP composites ...

    African Journals Online (AJOL)

    However, the users of FRP are facing difficulties to machine it, because of fiber delamination, fiber pull out, short tool life, matrix debonding and formation of powder like chips. The present ... A second order mathematical model was developed for surface roughness prediction using Response Surface Methodology (RSM).

  15. Determining the Effect of Cutting Parameters on Surface Roughness ...

    African Journals Online (AJOL)

    The aim of present research focuses on the prediction of machining parameters that improve the quality of surface finish. The surface roughness is one of the important properties of work piece quality in the CNC (Computer Numerical Control) turning process. An effective approach of optimization techniques genetic ...

  16. RMS slope of exponentially correlated surface roughness for radar applications

    DEFF Research Database (Denmark)

    Dierking, Wolfgang

    2000-01-01

    In radar signature analysis, the root mean square (RMS) surface slope is utilized to assess the relative contribution of multiple scattering effects. For an exponentially correlated surface, an effective RMS slope can be determined by truncating the high frequency tail of the roughness spectrum...

  17. Estimation of scattering from a moist rough surface with spheroidal ...

    Indian Academy of Sciences (India)

    Administrator

    less than 5⋅5% of the magnetic wavelength. We empha- size that the surface deviation is responsible for scattering at a given electromagnetic wavelength. 2. Theoretical consideration (basic theory). We consider a horizontally rough surface with slight per- centage of moisture (2–4⋅5%) with spheroidal dust parti- cles.

  18. Roughness evolution of Si surfaces upon Ar ion erosion

    NARCIS (Netherlands)

    de Rooij-Lohmann, Vita; Kozhevnikov, I. V.; Peverini, L.; Ziegler, E.; Cuerno, R.; F. Bijkerk,; Yakshin, A. E.

    2010-01-01

    We studied the roughness evolution of Si surfaces upon Ar ion erosion in real time. Following the theory of surface kinetic roughening, a model proposed by Majaniemi was used to obtain the value of the dynamic scaling exponent beta from our data. The model was found to explain both the observed

  19. Surface roughness and cutting force estimation in the CNC turning using artificial neural networks

    Directory of Open Access Journals (Sweden)

    Mohammad Ramezani

    2015-04-01

    Full Text Available Surface roughness and cutting forces are considered as important factors to determine machinability rate and the quality of product. A number of factors like cutting speed, feed rate, depth of cutting and tool noise radius influence the surface roughness and cutting forces in turning process. In this paper, an Artificial Neural Network (ANN model was used to forecast surface roughness and cutting forces with related inputs, including cutting speed, feed rate, depth of cut and tool noise radius. The machined surface roughness and cutting force parameters related to input parameters are the outputs of the ANN model. In this work, 24 samples of experimental data were used to train the network. Moreover, eight other experimental tests were implemented to test the network. The study concludes that ANN was a reliable and accurate method for predicting machining parameters in CNC turning operation.

  20. The effect of brushing with toothpaste containing nano calcium carbonate upon nanofill composite resin surface roughness

    Science.gov (United States)

    Ramadhani, A. M.; Herda, E.; Triaminingsih, S.

    2017-08-01

    This study aims to determine the effect of brushing with toothpaste containing nanocalcium carbonate on the roughness of nanofill composite resin surface. Brushing was conducted with 3 types of materials for 3 consecutive brushing periods of 10 minutes each. Surface roughness was measured using a surface-roughness tester and the results were analyzed using the repeated ANOVA and the one-way ANOVA test. The surface morphology was observed using SEM after 3 months’ worth of brushing with the 3 materials. It was found that the nanofill composite resin surface-roughness value increased significantly (p<0.005) after brushing with toothpaste containing nano calcium carbonate for 3 months, but the value was not as high as that obtained when brushing with other types of toothpaste.

  1. Velocity profiles and surface roughness under breaking waves

    Science.gov (United States)

    Craig, Peter D.

    1996-01-01

    Recent measurements under wave-breaking conditions in the ocean, lakes, and tanks reveal a layer immediately below the surface in which dissipation decays as depth to the power -2 to -4 and downwind velocities are approximately linear with depth. This behavior is consistent with predictions of a conventional, one-dimensional, level 2.5 turbulence closure model, in which the influence of breaking waves is parameterized as a surface source of turbulent kinetic energy. The model provides an analytic solution which describes the near-surface power law behavior and the deeper transition to the "law of the wall." The mixing length imposed in the model increases linearly away from a minimum value, the roughness length, at the surface. The surface roughness emerges as an important scaling factor in the wave-enhanced layer but is the major unknown in the formulation. Measurements in the wave-affected layer are still rare, but one exceptional set, both in terms of its accuracy and proximity to the surface, is that collected by Cheung and Street [1988] in the Stanford wind tunnel. Their velocity profiles first confirm the accuracy of the model, and, second, allow estimation, via a best fit procedure, of roughness lengths at five different wind speeds. Conclusions are tentative but indicate that the roughness length increases with wind speed and appears to take a value of approximately one sixth the dominant surface wavelength. A more traditional wall-layer model, which ignores the flux of turbulent kinetic energy, will also accurately reproduce the measured velocity profiles. In this case, enhanced surface turbulence is forced on the model by the assumption of a large surface roughness, three times that required by the full model. However, the wall-layer model cannot predict the enhanced dissipation near the surface.

  2. Predicting the surface roughness in the dry machining of duplex stainless steel (DSS

    Directory of Open Access Journals (Sweden)

    G. Krolczyk

    2013-04-01

    Full Text Available This paper examines the influence of cutting parameters, namely cutting speed, feed and depth of cut onto surface roughness after DSS turning process. The study included developing a mathematical model to determine the surface roughness. Verification research has been carried out on CNC lathe; hence the test plan has been adjusted to the possibility of programmable machines controlling GE Fanuc Series 0-T. The comparison of results obtained by given experimental plan was performed in industrial company.

  3. Random phase mask as a model of a rough surface

    International Nuclear Information System (INIS)

    Svitasheva, S.N.

    2011-01-01

    Artificial roughness was created on sample surfaces by etching through a two-dimensional orthogonal grating with a stochastic distribution of square 'defects' of size. 'Defects' depth was varied from 0.02 μm up to 1.005 μm. The experimental dependences of the scattering of polarized light were studied on four types of surface roughness for two materials: quartz and aluminum. The defect sizes of the random phase mask were 25 x 25 μm and 2.5 x 2.5 μm. The impacts of the sizes and density of artificial defects of rough surfaces on the polarization of reflected light were investigated by multiple-angle-of-incidence (MAI) ellipsometry at a wavelength of 0.63 μm.

  4. Monitoring tablet surface roughness during the film coating process

    DEFF Research Database (Denmark)

    Seitavuopio, Paulus; Heinämäki, Jyrki; Rantanen, Jukka

    2006-01-01

    the process of film coating tablets were studied by noncontact laser profilometry and scanning electron microscopy (SEM). An EDX analysis was used to monitor the magnesium stearate and titanium dioxide of the tablets. The tablet cores were film coated with aqueous hydroxypropyl methylcellulose, and the film......The purpose of this study was to evaluate the change of surface roughness and the development of the film during the film coating process using laser profilometer roughness measurements, SEM imaging, and energy dispersive X-ray (EDX) analysis. Surface roughness and texture changes developing during...... coating was performed using an instrumented pilot-scale side-vented drum coater. The SEM images of the film-coated tablets showed that within the first 30 minutes, the surface of the tablet cores was completely covered with a thin film. The magnesium signal that was monitored by SEM-EDX disappeared after...

  5. Applying Terrestrial Laser Scanning for Soil Surface Roughness Assessment

    Directory of Open Access Journals (Sweden)

    Milutin Milenković

    2015-02-01

    Full Text Available Terrestrial laser scanning can provide high-resolution, two-dimensional sampling of soil surface roughness. While previous studies demonstrated the usefulness of these roughness measurements in geophysical applications, questions about the number of required scans and their resolution were not investigated thoroughly. Here, we suggest a method to generate digital elevation models, while preserving the surface’s stochastic properties at high frequencies and additionally providing an estimate of their spatial resolution. We also study the impact of the number and positions of scans on roughness indices’ estimates. An experiment over a smooth and isotropic soil plot accompanies the analysis, where scanning results are compared to results from active triangulation. The roughness measurement conditions for ideal sampling are revisited and updated for diffraction-limited sampling valid for close-range laser scanning over smooth and isotropic soil roughness. Our results show that terrestrial laser scanning can be readily used for roughness assessment on scales larger than 5 cm, while for smaller scales, special processing is required to mitigate the effect of the laser beam footprint. Interestingly, classical roughness parametrization (correlation length, root mean square height (RMSh was not sensitive to these effects. Furthermore, comparing the classical roughness parametrization between one- and four-scan setups shows that the one-scan data can replace the four-scan setup with a relative loss of accuracy below 1% for ranges up to 3 m and incidence angles no larger than 50°, while two opposite scans can replace it over the whole plot. The incidence angle limit for the spectral slope is even stronger and is 40°. These findings are valid for scanning over smooth and isotropic soil roughness.

  6. The influence of machining condition and cutting tool wear on surface roughness of AISI 4340 steel

    Science.gov (United States)

    Natasha, A. R.; Ghani, J. A.; Che Haron, C. H.; Syarif, J.

    2018-01-01

    Sustainable machining by using cryogenic coolant as the cutting fluid has been proven to enhance some machining outputs. The main objective of the current work was to investigate the influence of machining conditions; dry and cryogenic, as well as the cutting tool wear on the machined surface roughness of AISI 4340 steel. The experimental tests were performed using chemical vapor deposition (CVD) coated carbide inserts. The value of machined surface roughness were measured at 3 cutting intervals; beginning, middle, and end of the cutting based on the readings of the tool flank wear. The results revealed that cryogenic turning had the greatest influence on surface roughness when machined at lower cutting speed and higher feed rate. Meanwhile, the cutting tool wear was also found to influence the surface roughness, either improving it or deteriorating it, based on the severity and the mechanism of the flank wear.

  7. Surface roughness control by extreme ultraviolet (EUV) radiation

    Science.gov (United States)

    Ahad, Inam Ul; Obeidi, Muhannad Ahmed; Budner, Bogusław; Bartnik, Andrzej; Fiedorowicz, Henryk; Brabazon, Dermot

    2017-10-01

    Surface roughness control of polymeric materials is often desirable in various biomedical engineering applications related to biocompatibility control, separation science and surface wettability control. In this study, Polyethylene terephthalate (PET) polymer films were irradiated with Extreme ultraviolet (EUV) photons in nitrogen environment and investigations were performed on surface roughness modification via EUV exposure. The samples were irradiated at 3 mm and 4 mm distance from the focal spot to investigate the effect of EUV fluence on topography. The topography of the EUV treated PET samples were studied by AFM. The detailed scanning was also performed on the sample irradiated at 3 mm. It was observed that the average surface roughness of PET samples was increased from 9 nm (pristine sample) to 280 nm and 253 nm for EUV irradiated samples. Detailed AFM studies confirmed the presence of 1.8 mm wide period U-shaped channels in EUV exposed PET samples. The walls of the channels were having FWHM of about 0.4 mm. The channels were created due to translatory movements of the sample in horizontal and transverse directions during the EUV exposure. The increased surface roughness is useful for many applications. The nanoscale channels fabricated by EUV exposure could be interesting for microfluidic applications based on lab-on-a-chip (LOC) devices.

  8. Depolarization of light by rough surface of scattering phantoms

    Science.gov (United States)

    Tchvialeva, Lioudmila; Markhvida, Igor; Lee, Tim K.; Doronin, Alexander; Meglinski, Igor

    2013-02-01

    The growing interest in biomedical optics to the polarimetric methods push researchers to better understand of light depolarization during scattering in and on the surface of biological tissues. Here we study the depolarization of light propagated in silicone phantoms. The phantoms with variety of surface roughness and bulk optical properties are designed to imitate human skin. Free-space speckle patterns in parallel (III) and perpendicular (I⊥) direction in respect to incident polarization are used to get the depolarization ratio of backscattered light DR = (III - I⊥)/( III + I⊥). The Monte Carlo model developed in house is also applied to compare simulated DR with experimentally measured. DR dependence on roughness, concentration and size of scattering particles is analysed. A weak depolarization and negligible response to scattering of the medium are observed for phantoms with smooth surfaces, whereas for the surface roughness in order to the mean free path the depolarization ratio decreases and reveals dependence on the bulk scattering coefficient. In is shown that the surface roughness could be a key factor triggering the ability of tissues' characterization by depolarization ratio.

  9. The Impedance Due to the Roughness of Metallic Surface

    Energy Technology Data Exchange (ETDEWEB)

    Bane, Karl L.F.; Chao, Alex W.; Ng, Cho-K.; /SLAC

    2011-08-26

    In some future accelerator designs, such as that of the Linear Coherent Light Source (LCLS), the bunch is very short, with an rms length on the order of 10's of microns, and the effective skin depth of the vacuum chamber walls can be very small compared to 1 micron. If the skin depth is small compared to the scale of the surface roughness then the wakefield due to the walls will be dominated by the roughness, and not by the wall resistance. To estimate the wakefields of a rough, metallic surface we begin with a simple, analytical model. Then we apply the MAFIA 3-dimensional, time-domain computer module, T3 to check and find the correct coefficient for the model.

  10. Study the Relationship between Pavement Surface Distress and Roughness Data

    Directory of Open Access Journals (Sweden)

    Mubaraki Muhammad

    2016-01-01

    Full Text Available In this paper, pavement sections from the highway connected Jeddah to Jazan were selected and analyzed to investigate the relationship between International Roughness Index (IRI and pavement damage including; cracking, rutting, and raveling. The Ministry of Transport (MOT of Saudi Arabia has been collecting pavement condition data using the Road Surface Tester (RST vehicle. The MOT measures Roughness, Rutting (RUT, Cracking (CRA, raveling (RAV. Roughness measurements are calculated in terms of the International Roughness Index (IRI. The IRI is calculated over equally spaced intervals along the road profile. Roughness measurements are performed at speed between at 80 kilometers per hour. Thus RST vehicle has been used to evaluate highways across the country. The paper shows three relationships including; cracking (CRA verses roughness (IRI, rutting (RUT verses IRI, and raveling (RAV verses IRI. Also, the paper developed two models namely; model relates IRI to the three distress under study, and model relates IRI to ride quality. The results of the analysis claim at 95% confidence that a significant relationship exist between IRI and cracking, and raveling. It’s also shown that rutting did not show significant relationship to IRI values. That’s leads to conclude that the distresses types: cracking and raveling may possibly be described as ride quality distresses at different level of significant. Rutting distress described as non-ride quality type’s distresses.

  11. Effect of surface roughness on the heating rates of large-angled hypersonic blunt cones

    Science.gov (United States)

    Irimpan, Kiran Joy; Menezes, Viren

    2018-03-01

    Surface-roughness caused by the residue of an ablative Thermal Protection System (TPS) can alter the turbulence level and surface heating rates on a hypersonic re-entry capsule. Large-scale surface-roughness that could represent an ablated TPS, was introduced over the forebody of a 120° apex angle blunt cone, in order to test for its influence on surface heating rates in a hypersonic freestream of Mach 8.8. The surface heat transfer rates measured on smooth and roughened models under the same freestream conditions were compared. The hypersonic flow-fields of the smooth and rough-surfaced models were visualized to analyse the flow physics. Qualitative numerical simulations and pressure measurements were carried out to have an insight into the high-speed flow physics. Experimental observations under moderate Reynolds numbers indicated a delayed transition and an overall reduction of 17-46% in surface heating rates on the roughened model.

  12. Modeling and analysis for surface roughness and material removal ...

    African Journals Online (AJOL)

    user

    terms of cutting parameters is also developed using regression modeling. The results indicate that the developed model is suitable for prediction of surface roughness and material removal rate in machining of unidirectional glass fiber reinforced plastics (UD-GFRP) composites. The predicted values and measured values ...

  13. Wane detection on rough lumber using surface approximation

    Science.gov (United States)

    Sang-Mook Lee; A. Lynn Abbott; Daniel L. Schmoldt

    2000-01-01

    The initial breakdown of hardwood logs into lumber produces boards with rough surfaces. These boards contain wane (missing wood due to the curved log exterior) that is removed by edge and trim cuts prior to sale. Because hardwood lumber value is determined using a combination of board size and quality, knowledge of wane position and defects is essential for selecting...

  14. Surface roughness and morphologic changes of zirconia: Effect of ...

    African Journals Online (AJOL)

    Purpose: The purpose of this study was to investigate the surface roughness and morphologic changes of pre.sintered ZrO2 after sandblasting and erbium, chromium: Yttrium, scandium, gallium, garnet (Er, Cr: YSGG) laser application of different intensities. Material and Methods: Eighty pre-sintered ZrO2 cylinders (7 mm ...

  15. Industrial characterization of nano-scale roughness on polished surfaces

    DEFF Research Database (Denmark)

    Feidenhans'l, Nikolaj Agentoft; Hansen, Poul-Erik; Pilny, Lukas

    2015-01-01

    We report a correlation between the scattering value “Aq” and the ISO standardized roughness parameter Rq. The Aq value is a measure for surface smoothness, and can easily be determined from an optical scattering measurement. The correlation equation extrapolates the Aq value from a narrow measur...

  16. Efficacy of Polishing Kits on the Surface Roughness and Color ...

    African Journals Online (AJOL)

    2017-05-22

    May 22, 2017 ... [8]. The. Address for correspondence: Dr. H Gumus,. Department of Pedodontics, Faculty of Dentistry, .... for 5 min and then blotted with dry tissue paper before color measurements were taken.[1] The ..... of a modeling resin and thermocycling on the surface hardness, roughness, and color of different resin ...

  17. Modeling and analysis for surface roughness and material removal ...

    African Journals Online (AJOL)

    International Journal of Engineering, Science and Technology ... A multiple objective utility model has been studied to optimize both the dependent parameters. ... Keywords: UD-GFRP composites, ANOVA, multi response optimization, utility concept, regression modeling, surface roughness, material removal rate, ...

  18. Abrasive wear and surface roughness of contemporary dental composite resin.

    Science.gov (United States)

    Han, Jian-min; Zhang, Hongyu; Choe, Hyo-Sun; Lin, Hong; Zheng, Gang; Hong, Guang

    2014-01-01

    The purpose of this study was to evaluate the abrasive wear and surface roughness of 20 currently available commercial dental composite resins, including nanofilled, supra-nanofilled, nanohybrid and microhybrid composite resins. The volume loss, maximum vertical loss, surface roughness (R(a)) and surface morphology [Scanning electron microscopy (SEM)] were determined after wear. The inorganic filler content was determined by thermogravimetric analysis. The result showed that the volume loss and vertical loss varied among the materials. The coefficients of determination (R(2)) of wear volume loss and filler content (wt%) was 0.283. SEM micrographs revealed nanofilled composites displayed a relatively uniform wear surfaces with nanoclusters protrusion, while the performance of nanohybrid composites varied. The abrasive wear resistance of contemporary dental composite resins is material-dependent and cannot be deduced from its category, filler loading and composite matrix; The abrasive wear resistance of some flowable composites is comparable to the universal/posterior composite resins.

  19. Biofilm retention on surfaces with variable roughness and hydrophobicity

    DEFF Research Database (Denmark)

    Tang, Lone; Pillai, Saju; Revsbech, Niels Peter

    2011-01-01

    Biofilms on food processing equipment cause food spoilage and pose a hazard to consumers. The bacterial community on steel surfaces in a butcher’s shop was characterized, and bacteria representative of this community enriched from minced pork were used to study biofilm retention. Stainless steel......-gel, but the bacterial community contained fewer Pseudomonas cells. In conclusion, biofilm retention was affected more by surface roughness than chemical composition under the condition described in this study....

  20. Optimization of surface roughness parameters in dry turning

    OpenAIRE

    R.A. Mahdavinejad; H. Sharifi Bidgoli

    2009-01-01

    Purpose: The precision of machine tools on one hand and the input setup parameters on the other hand, are strongly influenced in main output machining parameters such as stock removal, toll wear ratio and surface roughnes.Design/methodology/approach: There are a lot of input parameters which are effective in the variations of these output parameters. In CNC machines, the optimization of machining process in order to predict surface roughness is very important.Findings: From this point of view...

  1. Surface roughness when diamond turning RSA 905 optical aluminium

    Science.gov (United States)

    Otieno, T.; Abou-El-Hossein, K.; Hsu, W. Y.; Cheng, Y. C.; Mkoko, Z.

    2015-08-01

    Ultra-high precision machining is used intensively in the photonics industry for the production of various optical components. Aluminium alloys have proven to be advantageous and are most commonly used over other materials to make various optical components. Recently, the increasing demand from optical systems for optical aluminium with consistent material properties has led to the development of newly modified grades of aluminium alloys produced by rapid solidification in the foundry process. These new aluminium grades are characterised by their finer microstructures and refined mechanical and physical properties. However the machining database of these new optical aluminium grades is limited and more research is still required to investigate their machinability performance when they are diamond turned in ultrahigh precision manufacturing environment. This work investigates the machinability of rapidly solidified aluminium RSA 905 by varying a number of diamond-turning cutting parameters and measuring the surface roughness over a cutting distance of 4 km. The machining parameters varied in this study were the cutting speed, feed rate and depth of cut. The results showed a common trend of decrease in surface roughness with increasing cutting distance. The lowest surface roughness Ra result obtained after 4 km in this study was 3.2 nm. This roughness values was achieved using a cutting speed of 1750 rpm, feed rate of 5 mm/min and depth of cut equal to 25 μm.

  2. New horizons in selective laser sintering surface roughness characterization

    Science.gov (United States)

    Vetterli, M.; Schmid, M.; Knapp, W.; Wegener, K.

    2017-12-01

    Powder-based additive manufacturing of polymers and metals has evolved from a prototyping technology to an industrial process for the fabrication of small to medium series of complex geometry parts. Unfortunately due to the processing of powder as a basis material and the successive addition of layers to produce components, a significant surface roughness inherent to the process has been observed since the first use of such technologies. A novel characterization method based on an elastomeric pad coated with a reflective layer, the Gelsight, was found to be reliable and fast to characterize surfaces processed by selective laser sintering (SLS) of polymers. With help of this method, a qualitative and quantitative investigation of SLS surfaces is feasible. Repeatability and reproducibility investigations are performed for both 2D and 3D areal roughness parameters. Based on the good results, the Gelsight is used for the optimization of vertical SLS surfaces. A model built on laser scanning parameters is proposed and after confirmation could achieve a roughness reduction of 10% based on the S q parameter. The Gelsight could be successfully identified as a fast, reliable and versatile surface topography characterization method as it applies to all kind of surfaces.

  3. Effect of delaying toothbrushing during bleaching on enamel surface roughness: an in vitro study.

    Science.gov (United States)

    Navimipour, E J; Mohammadi, N; Mostafazadeh, S; Ghojazadeh, M; Oskoee, P A

    2013-01-01

    This study aimed to evaluate the effect of toothbrushing on enamel surface roughness at three different intervals after daily bleaching treatment. Eighty enamel slabs were initially evaluated for surface roughness and then randomly divided into four groups. The bleaching procedure was carried out for 21 days, six hours daily. In the control group (group 1), the specimens were not brushed after bleaching, but in groups 2-4, they were brushed with toothpaste immediately, one hour, or two hours after bleaching, respectively. Then the specimens were stored in artificial saliva. Enamel surface roughness was reevaluated at the end of the period. Kruskal-Wallis and Mann-Whitney U tests showed statistically significant differences in the means of surface roughness values between the immediately brushed group and the three other groups (ptoothbrushing immediately after bleaching increased enamel surface roughness; however, postponing the procedure for one or two hours after daily bleaching and exposing the specimens to artificial saliva during the study period resulted in enamel surface roughness comparable to that of the control group.

  4. Surface roughness and adaptation of different materials to secure implant attachment housings.

    Science.gov (United States)

    Ozkir, Serhat Emre; Yilmaz, Burak; Kurkcuoglu, Isin; Culhaoglu, Ahmet; Unal, Server Mutluay

    2017-01-01

    Various materials are available to secure implant attachment housings in overdentures. Surface roughness and the adaptation of these materials to the denture base and the housings may increase the microcracks and bacterial adhesion at the interfaces in the long term. The surface characteristics of the interface between the denture base orientation material and the attachment housing have not been extensively studied. The purpose of this in vitro study was to evaluate the surface roughness and the adaptation of 5 different housing orientation materials to the housings and the denture base. Fifty-five poly(methyl methacrylate) (PMMA) specimens (15 mm in diameter and 4 mm in height) were prepared with a clearance inside to allow the insertion of overdenture housings. Five different materials were used for housing orientation (Quick Up, Ufi Gel Hard, Tokuyama Rebase II Fast, Meliodent, and Paladent). The specimens were thermocycled 5000 times between 5°C and 55°C. The surface roughness (Ra values) of the specimens was measured with a noncontact profilometer. Scanning electron images were made in order to inspect the PMMA-orientation material-housing interfaces. The Kruskal-Wallis test was used to investigate the differences between the surface roughness values of the orientation materials, and the Iman-Conover test was used for pairwise comparisons (α=.05). The surface roughness values significantly differed between Quick up and Ufi Gel orientation materials only, and Quick up had smaller surface roughness values than Ufi Gel (P=.009). Microcracks were observed among the groups only at the junction of the orientation material and the housing after thermocycling. Ufi Gel Hard showed the roughest surfaces around the overdenture attachment housings. The adaptation between the orientation material and the housing may deteriorate, and increased surface roughness and microcrack formation may be seen around the housings. Copyright © 2016 Editorial Council for the

  5. Effect of ethylenediamine tetraacetic acid and etidronic acid on the surface roughness of Biodentine: in vitro

    Directory of Open Access Journals (Sweden)

    Özgür İlke Atasoy Ulusoy

    2017-01-01

    Full Text Available Objective: The aim of this study was to evaluate the effect of 9% etidronic acid (HEBP and 17% ethylenediamine tetraacetic acid (EDTA on the surface roughness of Biodentine. Materials and Method: Biodentine (Septodont was mixed according to the manufacturer’s instructions. Briefly, five drops of liquid were added into the capsule containing the powder. Then the capsule was placed in a triturator for 30 sec. The prepared mixture was placed into a mold (diameter: 5 mm, depth: 3 mm. The Biodentine surfaces were polished with silicon carbide abrasive papers. The surface roughness of 30 samples was measured at baseline using a portable surface roughness tester. For this purpose, a 5 mN force was applied onto three different locations of the samples with a speed of 0.8 mm/sec. The samples were divided into two groups according to the irrigation solution (n=15; first group was treated with 9% HEBP, and the second group was treated with 17% EDTA. The surface roughness of the samples was measured again after 1 and 2 min of irrigant application. Data were statistically analyzed using one-way ANOVA and independent sample t-test. Results: For HEBP, no significant difference was found between the surface roughness values at 0., 1., and 2 min (p=0.107; ANOVA. For EDTA, the surface roughness value at 1 min was significantly greater than the baseline value (p<0.001; t-test. The surface roughness changes at the two time periods were significantly different between the EDTA and HEBP groups (p=0.003 for 0-1 min passage, p=0.021 for 1-2 min passage. Conclusion: The use of 17% EDTA may result in deterioration of Biodentine’s surface during perforation repair and root canal treatment.

  6. The role of the roughness spectral breadth in elastic contact of rough surfaces

    Science.gov (United States)

    Yastrebov, Vladislav A.; Anciaux, Guillaume; Molinari, Jean-François

    2017-10-01

    We study frictionless and non-adhesive contact between elastic half-spaces with self-affine surfaces. Using a recently suggested corrective technique, we ensure an unprecedented accuracy in computation of the true contact area evolution under increasing pressure. This accuracy enables us to draw conclusions on the role of the surface's spectrum breadth (Nayak parameter) in the contact area evolution. We show that for a given normalized pressure, the contact area decreases logarithmically with the Nayak parameter. By linking the Nayak parameter with the Hurst exponent (or fractal dimension), we show the effect of the latter on the true contact area. This effect, undetectable for surfaces with poor spectral content, is quite strong for surfaces with rich spectra. Numerical results are compared with analytical models and other available numerical results. A phenomenological equation for the contact area growth is suggested with coefficients depending on the Nayak parameter. Using this equation, the pressure-dependent friction coefficient is deduced based on the adhesive theory of friction. Some observations on Persson's model of rough contact, whose prediction does not depend on Nayak parameter, are reported. Overall, the paper provides a unifying picture of rough elastic contact and clarifies discrepancies between preceding results.

  7. Surface forces between rough and topographically structured interfaces

    DEFF Research Database (Denmark)

    Thormann, Esben

    2017-01-01

    and manufactured materials, which possess topographical variations. Further, with technological advances in nanotechnology, fabrication of nano- or micro-structured surfaces has become increasingly important for many applications, which calls for a better understanding of the effect of surface topography...... on the interaction between interfaces. This paper presents a review of the current state of understanding of the effect of surface roughness on DLVO forces, as well as on the interactions between topographically structured hydrophobic surfaces in water. While the first case is a natural choice because it represents...

  8. Acoustic imaging in application to reconstruction of rough rigid surface with airborne ultrasound waves

    Science.gov (United States)

    Krynkin, A.; Dolcetti, G.; Hunting, S.

    2017-02-01

    Accurate reconstruction of the surface roughness is of high importance to various areas of science and engineering. One important application of this technology is for remote monitoring of open channel flows through observing its dynamic surface roughness. In this paper a novel airborne acoustic method of roughness reconstruction is proposed and tested with a static rigid rough surface. This method is based on the acoustic holography principle and Kirchhoff approximation which make use of acoustic pressure data collected at multiple receiver points spread along an arch. The Tikhonov regularisation and generalised cross validation technique are used to solve the underdetermined system of equations for the acoustic pressures. The experimental data are collected above a roughness created with a 3D printer. For the given surface, it is shown that the proposed method works well with the various number of receiver positions. In this paper, the tested ratios between the number of surface points at which the surface elevation can be reconstructed and number of receiver positions are 2.5, 5, and 7.5. It is shown that, in a region comparable with the projected size of the main directivity lobe, the method is able to reconstruct the spatial spectrum density of the actual surface elevation with the accuracy of 20%.

  9. Asperity interaction in adhesive contact of metallic rough surfaces

    International Nuclear Information System (INIS)

    Sahoo, Prasanta; Banerjee, Atanu

    2005-01-01

    The analysis of adhesive contact of metallic rough surfaces considering the effect of asperity interaction is the subject of this investigation. The micro-contact model of asperity interactions developed by Zhao and Chang (2001 Trans. ASME: J. Tribol. 123 857-64) is combined with the elastic plastic adhesive contact model developed by Chang et al (1988 Trans. ASME: J. Tribol. 110 50-6) to consider the asperity interaction and elastic-plastic deformation in the presence of surface forces simultaneously. The well-established elastic adhesion index and plasticity index are used to consider the different contact conditions. Results show that asperity interaction influences the load-separation behaviour in elastic-plastic adhesive contact of metallic rough surfaces significantly and, in general, adhesion is reduced due to asperity interactions

  10. Dependence of metal-enhanced fluorescence on surface roughness

    Science.gov (United States)

    François, Alexandre; Sciacca, Beniamino; Zuber, Agnieszka; Klantsataya, Elizaveta; Monro, Tanya M.

    2014-03-01

    Metal Enhanced Fluorescence (MEF) takes advantage of the coupling between surface plasmons, in either a metallic thin film or metallic nanoparticles, and fluorophores located in proximity of the metal, yielding an increase of the fluorophore emission. While MEF has been widely studied on metallic nanoparticles with the emphasis on creating brighter fluorescent labels, planar surfaces have not benefitted from the same attention. Here we investigate the influence of the surface roughness of a thin metallic film on the fluorescence enhancement. 50nm thick silver films were deposited on glass slides using either thermal evaporation with different evaporation currents or an electroless plating method based on the Tollens reaction to vary the surface roughness. Multiple layers of positively and negatively charged polyelectrolytes were deposited on top of the metallic coating to map out the enhancement factor as function of the gap between the metallic coating and fluorophore molecules covalently bound to the last polyelectrolyte layer. We show that fluorescence is enhanced by the presence of the metallic film, and in particular that the enhancement increases by a factor 3 to 40 for roughness ranging from 3 nm to 8 nm. Although these enhancement factors are modest compared to the enhancement produced by complex metallic nanoparticles or nano-patterned metallic thin films, the thin films used here are capable of supporting a plasmonic wave and offer the possibility of combining different techniques, such as surface plasmon resonance (with its higher refractive index sensitivity compared to localized plasmons) and MEF within a single device.

  11. Surface Roughness of Composite Resins after Simulated Toothbrushing with Different Dentifrices

    Science.gov (United States)

    Monteiro, Bruna; Spohr, Ana Maria

    2015-01-01

    Background: The aim of the study was to evaluate, in vitro, the surface roughness of two composite resins submitted to simulated toothbrushing with three different dentifrices. Materials and Methods: Totally, 36 samples of Z350XT and 36 samples of Empress Direct were built and randomly divided into three groups (n = 12) according to the dentifrice used (Oral-B Pro-Health Whitening [OBW], Colgate Sensitive Pro-Relief [CS], Colgate Total Clean Mint 12 [CT12]). The samples were submitted to 5,000, 10,000 or 20,000 cycles of simulated toothbrushing. After each simulated period, the surface roughness of the samples was measured using a roughness tester. Results: According to three-way analysis of variance, dentifrice (P = 0.044) and brushing time (P = 0.000) were significant. The composite resin was not significant (P = 0.381) and the interaction among the factors was not significant (P > 0.05). The mean values of the surface roughness (µm) followed by the same letter represent no statistical difference by Tukey's post-hoc test (P toothbrushing. The higher the brushing time, the higher the surface roughness of composite resins. The dentifrice OBW caused a higher surface roughness in both composite resins. PMID:26229362

  12. Effect of polishing systems on stain susceptibility and surface roughness of nanocomposite resin material.

    Science.gov (United States)

    Barakah, Haifa M; Taher, Nadia M

    2014-09-01

    Different polishing systems vary in their effect on reducing surface roughness and stain susceptibility of dental composite resin materials. The purpose of this study was to compare the effect of 3 polishing systems on the stain susceptibility and surface roughness of 2 nanocomposite resins and a microhybrid composite resin. Forty-five disks (2×10 mm) each were fabricated of 2 nanocomposite resins (Filtek Supreme XT and Tetric EvoCeram) and 1 microhybrid composite resin (Z250). Both sides of the disks were wet finished, and 1 side was polished with PoGo, Astropol, or Hi-Shine (n=5). Unpolished surfaces served as controls. The average roughness (Ra, μm) was measured with a profilometer, and the baseline color was recorded with a spectrophotometer. All specimens were incubated while soaking in a staining solution of coffee, green tea, and berry juice for 3 weeks. The color was recorded again, and the data were analyzed with 2-way ANOVA at α=.05 and Tukey multiple comparison tests. All polishing systems improved the staining resistance of Filtek Supreme XT and Z250 but did not affect that of Tetric EvoCeram. The surface color of Filtek Supreme XT was changed significantly and was the smoothest after polishing with PoGo, whereas Hi-Shine produced significantly rougher surfaces but with the lowest color change. Hi-Shine produced the highest color change in Z250. The surface roughness did not differ significantly between the other polishing systems. Tetric EvoCeram showed no significant differences in color change or surface roughness. Staining susceptibility and surface roughness depend mainly on material composition and on the polishing procedures. Polishing improves the staining resistance of composite resins. Nanocomposite resins did not exhibit better staining resistance or surface roughness than microhybrid composite resin. Copyright © 2014 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

  13. Effect of filler particles on surface roughness of experimental composite series

    Directory of Open Access Journals (Sweden)

    Hanadi Yousif Marghalani

    2010-02-01

    Full Text Available OBJECTIVE: The purpose of this study was to evaluate the effect of different filler sizes and shapes on the surface roughness of experimental resin-composite series. MATERIAL AND METHODS: Thirty-three disc-shaped specimens of the series (Spherical-RZD 102, 105, 106, 107, 114 and Irregular-RZD 103, 108, 109, 110, 111, 112 were prepared in a split Teflon mold and irradiated with an halogen light-curing unit (450 mW/cm² for 40 s at both top and bottom surfaces. The specimens were stored for 3 months in distilled water. The surface roughness values in form of surface finish-vertical parameter (Ra, maximum roughness depth (Rmax and horizontal roughness parameter (Sm were recorded using a contact profilometer. The data were analyzed by one-way ANOVA and the means were compared by Scheffé post-hoc test (a=0.05. RESULTS: The lowest surface roughness (Ra was observed in S-100 (0.079±0.013, while the roughest surface was noted in I-450/700/1000 (0.125±0.011 and I-450/1000 (0.124±0.004. The spherical-shape series showed the smoothest surface finish compared to the irregular-shape ones with higher significant difference (p>0.05. The vertical surface roughness parameter (Ra values increased as the filler size increased yielding a linear relation (r²=0.82. On the contrary, the horizontal parameter (Sm was not significantly affected by the filler size (r²=0.24 as well as the filler shape. CONCLUSIONS: Filler particle's size and shape have a great effect on the surface roughness parameters of these composite series.

  14. Effect of whitening dentifrices on the surface roughness of commercial composites.

    Science.gov (United States)

    Barbieri, Guilherme Machado; Mota, Eduardo Gonçalves; Rodrigues-Junior, Sinval Adalberto; Burnett, Luiz Henrique

    2011-10-01

    Our study aimed to test the null hypothesis that whitening and non-whitening dentifrices affect similarly the surface roughness of commercial microhybrid composites, independent of the brushing time. One hundred and ninety-two disc-shaped specimens of Filtek Z250 (3 M/ESPE, St. Paul, MN, USA) and Rok (SDI, Australia) were built up and randomly assigned to 24 groups, based on the dentifrices used (two whitening dentifrices: Colgate Max White-Colgate-Palmolive, São Bernardo do Campo, São Paulo, Brazil and Close Up Extra Whitening-Unilever, Brasil Higiene Pessoal e Limpeza Ltda, Ipojuca, Pernambuco, Brazil; and one non-whitening dentifrice: Colgate Total 12 Clean Mint-Colgate-Palmolive), and on the simulated brushing times (24 hours, 6, 12 and 24 months). The specimens were submitted to the toothbrushing regimens after which the surface roughness (Ra) was measured. Data was submitted to analysis of variance and Tukey test (α=0.05). The composite's surface roughness was significantly affected by the composites (p=0.0007), the dentifrices (p=0.0001), and the simulated brushing time (p=0.0001). Higher roughness was observed when the whitening dentifrices were used and when the brushing time increased. Filtek Z250 was more affected than Rok, especially after 24 months of simulated brushing. Whitening dentifrices produced higher surface roughness in the composites tested. The degree of surface compromising increased with brushing time and depends on the composite's microstructure and composition. © 2011 Wiley Periodicals, Inc.

  15. Information Pattern in Imaging of a Rough Surface

    Science.gov (United States)

    Abul’khanov, S. R.; Kazanskiy, N. L.

    2018-01-01

    In this paper, we have proposed a method of parametrization of a rough surface image based on its information pattern. We have determined that the image information pattern makes it possible to keep track of any variations in the number of pixels in the image of the controlled rough surface of at least 0.192 per cent of the total number of image pixels. The offered method permits to compensate a non-linear perception of the controlled surface by a human eye. We have determined a ratio of the number of these pixels to the total number of image pixels. Such ratios, was treated as a certain square area. We packed this squares without intercrossings in the square of 2. This type of squares packing was designated as an information pattern. Using the information pattern, the parameter value was obtained. We have determined that the parameter value can keep track of any variations of the number of pixels in the image of the rough surface from at least 0.192 percent.

  16. Biofilm retention on surfaces with variable roughness and hydrophobicity.

    Science.gov (United States)

    Tang, Lone; Pillai, Saju; Revsbech, Niels Peter; Schramm, Andreas; Bischoff, Claus; Meyer, Rikke Louise

    2011-01-01

    Biofilms on food processing equipment cause food spoilage and pose a hazard to consumers. The bacterial community on steel surfaces in a butcher's shop was characterized, and bacteria representative of this community enriched from minced pork were used to study biofilm retention. Stainless steel (SS) was compared to two novel nanostructured sol-gel coatings with differing hydrophobicity. Surfaces were characterized with respect to roughness, hydrophobicity, protein adsorption, biofilm retention, and community composition of the retained bacteria. Fewer bacteria were retained on the sol-gel coated surfaces compared to the rougher SS. However, the two sol-gel coatings did not differ in either protein adsorption, biofilm retention, or microbial community composition. When polished to a roughness similar to sol-gel, the SS was colonized by the same amount of bacteria as the sol-gel, but the bacterial community contained fewer Pseudomonas cells. In conclusion, biofilm retention was affected more by surface roughness than chemical composition under the condition described in this study.

  17. Effective macroscopic adhesive contact behavior induced by small surface roughness

    Science.gov (United States)

    Kesari, Haneesh; Lew, Adrian J.

    2011-12-01

    In this paper we study a model contact problem involving adhesive elastic frictionless contact between rough surfaces. The problem's most notable feature is that it captures the phenomenon of depth-dependent-hysteresis (DDH) (e.g., see Kesari et al., 2010), which refers to the observation of different contact forces during the loading and unloading stages of a contact experiment. We specifically study contact between a rigid axi-symmetric punch and an elastic half-space. The roughness is represented as arbitrary periodic undulations in the punch's radial profile. These undulations induce multiple equilibrium contact regions between the bodies at each indentation-depth. Assuming that the system evolves so as to minimize its potential energy, we show that different equilibrium contact regions are selected during the loading and unloading stages at each indentation-depth, giving rise to DDH. When the period and amplitude of our model's roughness is reduced, we show that the evolution of the contact force and radius with the indentation-depth can be approximated with simpler curves, the effective macroscopic behavior, which we compute. Remarkably, the effective behavior depends solely on the amplitude and period of the model's roughness. The effective behavior is useful for estimating material properties from contact experiments displaying DDH. We show one such example here. Using the effective behavior for a particular roughness model (sinusoidal) we analyze the energy loss during a loading/unloading cycle, finding that roughness can toughen the interface. We also estimate the energy barriers between the different equilibrium contact regions at a fixed indentation-depth, which can be used to assess the importance of ambient energy fluctuations on DDH.

  18. Rotating channel flows over rough and smooth surfaces

    Science.gov (United States)

    Piomelli, Ugo; Wu, Wen; Yuan, Junlin; Turbulence Simulation; Modelling Laboratory Team

    2017-11-01

    In wall-bounded flows rotating about the spanwise axis, if the signs of the rotation and mean vorticity vectors are the same, the flow tends to be de-stabilized; if they are opposite it may become more stable. In a channel, in which the vorticity has opposite signs near the two walls, one side is unstable and the other one stable. To investigate how roughness can change these dynamics, we performed DNS of channel flows with two rotation rates (Rob = 2 Ωδ /Ub = 0.42 and 1.0), over both smooth and rough surfaces. The roughness is modelled using an immersed-boundary method. At the high Rotation number, in the smooth case the Reynolds stresses vanish on the stable side, and the flow approaches 2D turbulence in the x - z plane. When the wall is rough, the increased momentum transfer due to the roughness results in significant and much more isotropic turbulent fluctuations. On the unstable side both rotation and roughness tend to de-stabilize the flow. Even at mild rotation rates Townsend's similarity hypothesis does not apply on the stable side, and only approximately on the unstable one. The role of production and redistribution due to rotation in the turbulent kinetic energy budget will be discussed. The authors acknowledge the support from Hydro-Québec and the NSERC Collaborative Research & Development program (CRDPJ 418786-11). The simulations were performed at CAC Queen't site. UP also thanks the support of Canada Research Chair Program.

  19. Interferometric microscopy study of the surface roughness of Portland cement under the action of different irrigants.

    Science.gov (United States)

    Ballester-Palacios, Maria L; Berástegui-Jimeno, Esther M; Parellada-Esquius, Neus; Canalda-Sahli, Carlos

    2013-09-01

    Some investigations suggested common Portland cement (PC) as a substitute material for MTA for endodontic use; both MTA and PC have a similar composition. The aim of this study was to determine the surface roughness of common PC before and after the exposition to different endodontic irrigating solutions: 10% and 20% citric acid, 17% ethylenediaminetetraacetic (EDTA) and 5% sodium hypochlorite. Fifty PC samples in the form of cubes were prepared. PC was mixed with distilled water (powder/liquid ratio 3:1 by weight). The samples were immersed for one minute in 10% and 20% citric acid, 17% EDTA and 5% sodium hypochlorite. After gold coating, PC samples were examined using the New View 100 Zygo interferometric microscope. It was used to examine and register the surface roughness and the profile of two different areas of each sample. Analysis of variance (ANOVA) was carried out, and as the requirements were not met, use was made of the Kruskal-Wallis test for analysis of the results obtained, followed by contrasts using Tukey's contrast tests. Sodium hypochlorite at a concentration of 5% significantly reduced the surface roughness of PC, while 20% citric acid significantly increased surface roughness. The other evaluated citric acid concentration (10%) slightly increased the surface roughness of PC, though statistical significance was not reached. EDTA at a concentration of 17% failed to modify PC surface roughness. Irrigation with 5% sodium hypochlorite and 20% citric acid lowered and raised the roughness values, respectively. The surface texture of PC is modified as the result of treatment with different irrigating solutions commonly used in endodontics, depending on their chemical composition and concentration.

  20. Differences in surface roughness of nanohybrid composites immersed in varying concentrations of citric acid

    Directory of Open Access Journals (Sweden)

    Gabriela Kevina Alifen

    2017-06-01

    Full Text Available Background: The surface roughness of restoration is important in predicting the length of time it might remain in the mouth. Conditions within the oral cavity can affect the surface roughness of a restoration. Nanohybrid composite is widely used in dentistry because it can be applied to restore anterior and posterior teeth. Athletes routinely consume isotonic drinks which are acidic and even more erosive than the carbonated variety because they contain a range of acids; the highest content of which being citric acid. Purpose: The aim of the study was to analyze the surface roughness of nanohybrid composite after having been subjected to immersion in varying concentrations of citric acid. Methods: Two isotonic drinks (Pocari Sweat and Mizone were analyzed using high performance liquid chromatography (HPLC to quantify the respective concentrations of citric acid which they contained. A total of 27 samples of cylindrical nanohybrid composite were prepared before being divided into three groups. In Group 1, samples were immersed in citric acid solution derived from Pocari Sweat. Those of Group 2 were immersed in citric acid solution derived from Mizone; while Group 3, samples were immersed in distilled water as a control. All samples were immersed for 7 days, before their surface roughness was tested by means of a surface roughness tester (Mitutoyo SJ-201. Data was analyzed using a one-way ANOVA test. Results: The results showed that there was no significant difference in surface roughness between Groups 1, 2 and 3 (p=0.985. Conclusion: No difference in surface roughness of nanohybrid composites results from prolonged immersion in varying concentrations of citric acid.

  1. Study of the possibility to measure the root-mean-square roughness of a shaded rough surface

    International Nuclear Information System (INIS)

    Mendeleev, V.Ya.

    2000-01-01

    The estimate of the root-mean-square roughness of a rough surface σ 1 is studied experimentally as a function of the angle of incidence. A surface with σ = 1.3 μm is illuminated by laser radiation with a wavelength of 0.633 μm. The angle of incidence of radiation on the surface under study is varied from 85 degree sign to 87.5 deg. σ 1 is estimated under the assumption that the regime of a slightly rough surface is fulfilled for the surface studied. Theoretical estimates of σ 1 are calculated in the Kirchhoff approximation with rough surface shadowing taken into account. The greatest relative difference between experimental and theoretical estimates of σ 1 does not exceed 0.07. The effect of rough surface shadowing on the estimate of σ is analyzed, and the possibility for exact measurement of σ 1 of a shaded rough surface is demonstrated in the case of a priori knowledge of the angle of incidence, for which this measurement is possible. A method that makes it possible to determine the angle of incidence, for which a good agreement between the measured value and the true value of σ of a shaded rough surface is possible, is proposed

  2. Effect of chemical degradation followed by toothbrushing on the surface roughness of restorative composites

    Directory of Open Access Journals (Sweden)

    Fernanda Regina Voltarelli

    2010-12-01

    Full Text Available OBJECTIVES: The aim of the present study was to assess the effect of the exposure to food-simulating liquids prior to brushing simulation on the surface roughness of five composite materials (Quixfil, Filtek Supreme, Esthet-X, Filtek Z250, Tetric Ceram. Material and METHODS: Twenty cylinders (5 mm diameter and 4 mm height of each composite were randomly allocated to 4 groups (n=5, according to the food-simulating liquid in which they were immersed for 7 days at 37°C: artificial saliva, heptane, citric acid, and ethanol. After this period, the top surface of composite cylinders was submitted to 7,500 brushing cycles (200 g load. Measurements of the surface roughness (Ra, ¼m were carried out before and after the exposure to the chemicals/brushing simulation. Changes on the morphology of composite surfaces were observed through scanning electron microscopy (SEM. RESULTS: The statistical analysis (ANOVA with cofactor / Tukey's test, α=5% detected a significant interaction between solutions and composite resins. Esthet-X, Filtek Z250 and Tetric Ceram were not affected by the food-simulating liquids/toothbrushing. Citric acid and ethanol increased the surface roughness of Quixfil and Filtek Supreme, respectively. SEM images corroborate the surface roughness findings, demonstrating the negative effect from chemical solutions and mechanical abrasion. CONCLUSIONS: The surface roughness of composite resin materials are differently affected by the food-simulating solutions, depending on the immersion media.

  3. Effect of chemical degradation followed by toothbrushing on the surface roughness of restorative composites

    Science.gov (United States)

    VOLTARELLI, Fernanda Regina; dos SANTOS-DAROZ, Claudia Batitucci; ALVES, Marcelo Corrêa; CAVALCANTI, Andrea Nóbrega; MARCHI, Giselle Maria

    2010-01-01

    Objectives The aim of the present study was to assess the effect of the exposure to food-simulating liquids prior to brushing simulation on the surface roughness of five composite materials (Quixfil, Filtek Supreme, Esthet-X, Filtek Z250, Tetric Ceram). Material and methods Twenty cylinders (5 mm diameter and 4 mm height) of each composite were randomly allocated to 4 groups (n=5), according to the food-simulating liquid in which they were immersed for 7 days at 37ºC: artificial saliva, heptane, citric acid, and ethanol. After this period, the top surface of composite cylinders was submitted to 7,500 brushing cycles (200 g load). Measurements of the surface roughness (Ra, µm) were carried out before and after the exposure to the chemicals/brushing simulation. Changes on the morphology of composite surfaces were observed through scanning electron microscopy (SEM). Results The statistical analysis (ANOVA with cofactor / Tukey's test, α=5%) detected a significant interaction between solutions and composite resins. Esthet-X, Filtek Z250 and Tetric Ceram were not affected by the food-simulating liquids/toothbrushing. Citric acid and ethanol increased the surface roughness of Quixfil and Filtek Supreme, respectively. SEM images corroborate the surface roughness findings, demonstrating the negative effect from chemical solutions and mechanical abrasion. Conclusions The surface roughness of composite resin materials are differently affected by the food-simulating solutions, depending on the immersion media. PMID:21308289

  4. Evaluation of the roughness of the surface of porcelain systems with the atomic force microscope

    International Nuclear Information System (INIS)

    Chavarria Rodriguez, Bernal

    2013-01-01

    The surface of a dental ceramic was evaluated and compared with an atomic force microscope after being treated with different systems of polishing. 14 identical ceramic Lava® Zirconia discs were used to test the different polishing systems. 3 polishing systems from different matrix houses were used to polish dental porcelain. The samples were evaluated quantitatively with an atomic force microscope in order to study the real effectiveness of each system, on the roughness average (Ra) and the maximum peak to valley roughness (Ry) of the ceramic surfaces. A considerable reduction of the surface roughness was obtained by applying different polishing systems on the surface of dental ceramics. Very reliable values of Ra and Ry were obtained by making measurements on the structure reproduced by the atomic force microscope. The advanced ceramics of zirconium oxide presented the best physical characteristics and low levels of surface roughness. A smoother surface was achieved with the application of polishing systems, thus demonstrating the reduction of the surface roughness of a dental ceramic [es

  5. Friction of hydrogels with controlled surface roughness on solid flat substrates.

    Science.gov (United States)

    Yashima, Shintaro; Takase, Natsuko; Kurokawa, Takayuki; Gong, Jian Ping

    2014-05-14

    This study investigated the effect of hydrogel surface roughness on its sliding friction against a solid substrate having modestly adhesive interaction with hydrogels under small normal pressure in water. The friction test was performed between bulk polyacrylamide hydrogels of varied surface roughness and a smooth glass substrate by using a strain-controlled rheometer with parallel-plates geometry. At small pressure (normal strain 1.4-3.6%), the flat surface gel showed a poor reproducibility in friction. In contrast, the gels with a surface roughness of 1-10 μm order showed well reproducible friction behaviors and their frictional stress was larger than that of the flat surface hydrogel. Furthermore, the flat gel showed an elasto-hydrodynamic transition while the rough gels showed a monotonous decrease of friction with velocity. The difference between the flat surface and the rough surface diminished with the increase of the normal pressure. These phenomena are associated with the different contact behaviors of these soft hydrogels in liquid, as revealed by the observation of the interface using a confocal laser microscope.

  6. Effect of surfaces similarity on contact resistance of fractal rough surfaces under cyclic loading

    Science.gov (United States)

    Gao, Yuanwen; Liu, Limei; Ta, Wurui; Song, Jihua

    2018-03-01

    Although numerous studies have shown that contact resistance depends significantly on roughness and fractal dimension, it remains elusive how they affect contact resistance between rough surfaces. The interface similarity index is first proposed to describe the similarity of the contact surfaces, which gives a good indication of the actual contact area between surfaces. We reveal that the surfaces' similarity be an origin of contact resistance variation. The cyclic loading can increase the contact stiffness, and the contact stiffness increases with the increase of the interface similarity index. These findings explain the mechanism of surface roughness and fractal dimension on contact resistance, and also provide reference for the reliability design of the electrical connection.

  7. Fuzzy Linguistic Optimization on Surface Roughness for CNC Turning

    OpenAIRE

    Lan, Tian-Syung

    2010-01-01

    Surface roughness is often considered the main purpose in contemporary computer numerical controlled (CNC) machining industry. Most existing optimization researches for CNC finish turning were either accomplished within certain manufacturing circumstances or achieved through numerous equipment operations. Therefore, a general deduction optimization scheme is deemed to be necessary for the industry. In this paper, the cutting depth, feed rate, speed, and tool nose runoff with low, medium, and...

  8. Estimation of scattering from a moist rough surface with spheroidal ...

    Indian Academy of Sciences (India)

    Administrator

    zontally polarized elastic wave propagating through the x, z plane, then the total scattered fields due to moisture spheroidal dust particles in rough surface is given as. (Dobson and Ulaby 1981),. 1. ( , ) d .d ,. 2 x x x y x y. E. U K K f K K π. ∞. −∞. = ∫ ∫. (3). 1. ( , ) d .d. 2 y y x y x y. E. U K K f K K π. ∞. −∞. = ∫ ∫. + cos cos.

  9. Metal substrates with nanometer scale surface roughness for flexible electronics

    Science.gov (United States)

    Lee, Jong-Lam; Kim, Kisoo

    2012-09-01

    In this work, we present a novel way in fabricating a metal substrate with nanometer scale in surface roughness (Ra INVAR (Invariable alloy) one (20 cm × 20 cm, Ra = 1.40 nm) were demonstrated. The INVAR film was used as a substrate for fabricating organic light emitting diodes (OLED) and organic photovoltaic (OPV). The optical and electrical characteristics of OLEDs and OPVs using the INVAR were comparable to those using a conventional ITO glass substrate.

  10. Computer simulation of RBS spectra from samples with surface roughness

    Czech Academy of Sciences Publication Activity Database

    Malinský, Petr; Hnatowicz, Vladimír; Macková, Anna

    2016-01-01

    Roč. 371, MAR (2016), s. 101-105 ISSN 0168-583X. [22nd International conference on Ion Beam Analysis (IBA). Opatija, 14.06.2015-19.06.2015] R&D Projects: GA MŠk(CZ) LM2011019; GA ČR GA15-01602S Institutional support: RVO:61389005 Keywords : computer simulation * Rutherford backscattering * surface roughness Subject RIV: BG - Nuclear, Atomic and Molecular Physics, Colliders Impact factor: 1.109, year: 2016

  11. Laser assisted fabrication of random rough surfaces for optoelectronics

    Energy Technology Data Exchange (ETDEWEB)

    Brissonneau, V., E-mail: vincent.brissonneau@im2np.fr [Thales Optronique SA, Avenue Gay-Lussac, 78995 Elancourt (France); Institut Materiaux Microelectronique Nanosciences de Provence, Aix Marseille Universite, Avenue Escadrille Normandie Niemen, 13397 Marseille (France); Escoubas, L. [Institut Materiaux Microelectronique Nanosciences de Provence, Aix Marseille Universite, Avenue Escadrille Normandie Niemen, 13397 Marseille (France); Flory, F. [Institut Materiaux Microelectronique Nanosciences de Provence, Ecole Centrale Marseille, Marseille (France); Berginc, G. [Thales Optronique SA, Avenue Gay-Lussac, 78995 Elancourt (France); Maire, G.; Giovannini, H. [Institut Fresnel, Aix Marseille Universite, Avenue Escadrille Normandie Niemen, 13397 Marseille (France)

    2012-09-15

    Highlights: Black-Right-Pointing-Pointer Random rough surfaces are photofabricated using an argon ion laser. Black-Right-Pointing-Pointer Speckle and surface correlation function are linked. Black-Right-Pointing-Pointer Exposure beam is modified allowing tuning the correlation. Black-Right-Pointing-Pointer Theoretical examples are presented. Black-Right-Pointing-Pointer Experimental results are compared with theoretical expectation. - Abstract: Optical surface structuring shows great interest for antireflective or scattering properties. Generally, fabricated surface structures are periodical but random surfaces that offer new degrees of freedom and possibilities by the control of their statistical properties. We propose an experimental method to create random rough surfaces on silicon by laser processing followed by etching. A photoresist is spin coated onto a silicon substrate and then exposed to the scattering of a modified laser beam. The beam modification is performed by using a micromirror matrix allowing laser beam shaping. An example of tuning is presented. An image composed of two white circles with a black background is displayed and the theoretical shape of the correlation is calculated. Experimental surfaces are elaborated and the correlation function calculated from height mapping. We finally compared the experimental and theoretical correlation functions.

  12. Simulation of secondary electron emission from rough surfaces

    International Nuclear Information System (INIS)

    Kawata, J.; Ohya, K.; Nishimura, K.

    1995-01-01

    The effect of surface roughness on the secondary electron emission from a beryllium surface under low-energy (≤1 keV) electron bombardment is investigated using a Monte Carlo simulation combined with the model of bowl-structured surface. With increasing aspect ratio H/W of the bowl structure, the secondary electron yield becomes greater than that for a flat surface, whereas for large H/W the yield is smaller; where H and W are the depth and width of the bowl structure, respectively. The former is due to emission of electrons, which cannot escape from the flat surface, from an inclined plane; it increases the low-energy component in the energy distribution. The latter is due to re-entrance of once-emitted electrons into the next part of the topographic surface; it decreases the number of electrons emitted with oblique angles. ((orig.))

  13. Mars radar clutter and surface roughness characteristics from MARSIS data

    Science.gov (United States)

    Campbell, Bruce A.; Schroeder, Dustin M.; Whitten, Jennifer L.

    2018-01-01

    Radar sounder studies of icy, sedimentary, and volcanic settings can be affected by reflections from surface topography surrounding the sensor nadir location. These off-nadir ;clutter; returns appear at similar time delays to subsurface echoes and complicate geologic interpretation. Additionally, broadening of the radar echo in delay by surface returns sets a limit on the detectability of subsurface interfaces. We use MARSIS 4 MHz data to study variations in the nadir and off-nadir clutter echoes, from about 300 km to 1000 km altitude, R, for a wide range of surface roughness. This analysis uses a new method of characterizing ionospheric attenuation to merge observations over a range of solar zenith angle and date. Mirror-like reflections should scale as R-2, but the observed 4 MHz nadir echoes often decline by a somewhat smaller power-law factor because MARSIS on-board processing increases the number of summed pulses with altitude. Prior predictions of the contributions from clutter suggest a steeper decline with R than the nadir echoes, but in very rough areas the ratio of off-nadir returns to nadir echoes shows instead an increase of about R1/2 with altitude. This is likely due in part to an increase in backscatter from the surface as the radar incidence angle at some round-trip time delay declines with increasing R. It is possible that nadir and clutter echo properties in other planetary sounding observations, including RIME and REASON flyby data for Europa, will vary in the same way with altitude, but there may be differences in the nature and scale of target roughness (e.g., icy versus rocky surfaces). We present global maps of the ionosphere- and altitude-corrected nadir echo strength, and of a ;clutter; parameter based on the ratio of off-nadir to nadir echoes. The clutter map offers a view of surface roughness at ∼75 m length scale, bridging the spatial-scale gap between SHARAD roughness estimates and MOLA-derived parameters.

  14. Effect of one-step polishing systems on surface roughness of different flowable restorative materials.

    Science.gov (United States)

    Ozel, Emre; Korkmaz, Yonca; Attar, Nuray; Karabulut, Erdem

    2008-11-01

    The purpose of this study was to investigate the influence of one-step polishing systems on the surface roughness of different flowable composites and a microhybrid composite. A total of 120 disks were fabricated and divided into six groups according to the different composite restorative materials tested (n = 20). Each group was further divided into four subgroups according to the polishing system (n = 5). For the control group, samples were left undisturbed after removal of Mylar strip. For the other three subgroups, samples were polished with PoGo, OptraPol, or Sof-Lex disks. Surface roughness was determined using a profilometer and observed under scanning electron microscope (SEM). Data were analyzed by one-way ANOVA and Duncan's multiple range test. For Tetric Flow, Grandio Flow, Filtek Supreme XT Flow, and Admira Flow, their lowest surface roughness values were obtained in Mylar Strip and PoGo groups. For Compoglass Flow, there were no significant differences between Mylar Strip, PoGo, and OptraPol. For Filtek Z250, the lowest surface roughness value was obtained with Mylar Strip. In light of the surface roughness results obtained, one-step polishing systems seemed to be a good choice for polishing flowable composites.

  15. The physics of water droplets on surfaces: exploring the effects of roughness and surface chemistry

    Science.gov (United States)

    Eid, K. F.; Panth, M.; Sommers, A. D.

    2018-03-01

    This paper explores the fluid property commonly called surface tension, its effect on droplet shape and contact angle, and the major influences of contact angle behaviour (i.e. surface roughness and surface chemistry). Images of water droplets placed on treated copper surfaces are used to measure the contact angles between the droplets and the surface. The surface wettability is manipulated either by growing a self-assembled monolayer on the surface to make it hydrophobic or by changing the surface roughness. The main activities in this experiment, then, are (1) preparing and studying surfaces with different surface wettability and roughness; (2) determining the shape and contact angles of water droplets on these surfaces; and (3) demonstrating the spontaneous motion of water droplets using surface tension gradients.

  16. Surface roughness of novel resin composites polished with one-step systems.

    Science.gov (United States)

    Ergücü, Z; Türkün, L S

    2007-01-01

    This study: 1) analyzed the surface roughness of five novel resin composites that contain nanoparticles after polishing with three different one-step systems and 2) evaluated the effectiveness of these polishers and their possible surface damage using scanning electron microscope (SEM) analysis. The resin composites evaluated in this study include CeramX, Filtek Supreme XT, Grandio, Premise and Tetric EvoCeram. A total of 100 discs (20/resin composites, 10 x 2 mm) were fabricated. Five specimens/resin composites cured under Mylar strips served as the control. The samples were polished for 30 seconds with PoGo, OptraPol and One Gloss discs at 15,000 rpm using a slow speed handpiece. The surfaces were tested for roughness (Ra) with a surface roughness tester and examined with SEM. One-way ANOVA was used for statistical analysis (p = 0.05). For all the composites tested, differences between the polishing systems were found to be significant (p Grandio, Mylar and PoGo created equally smooth surfaces, while OptraPol and One Gloss produced equally rougher surfaces. Tetric EvoCeram exhibited the roughest surface with OptraPol, while no significant differences were found between Premise and CeramX. According to SEM images, OptraPol and One Gloss scratched and plucked the particles away from the surface, while PoGo created a uniform finish, although the roughness values were not the same for each composite. Effectiveness of the polishers seems to be material dependent.

  17. The effects of finishing and polishing techniques on surface roughness and color stability of nanocomposites.

    Science.gov (United States)

    Gönülol, Nihan; Yilmaz, Fikret

    2012-12-01

    The aim of this in vitro study was to evaluate the effects of different finishing and polishing techniques on the surface roughness and color stability of nanocomposites. Two nanohybrid (Grandio, Aelite Aesthetic Enamel), two nanofill (Filtek Supreme XT Dentin and Translucent), and a microhybrid (Filtek Z250) composites were used. Two hundred and eighty disc-shaped specimens were cured under a mylar strip. Seven specimens of each resin composite were randomly assigned to one of the seven polishing systems. A profilometer was used for assessing surface roughness. ΔE was calculated with a colorimeter at baseline and 48 h after storage in a coffee solution. The results were analysed by two-way ANOVA and Tukey's HSD test (α=0.05). Regression analysis was used to examine the correlation between surface roughness and color stability (α=0.01). There was no significant difference in R(a) values between mylar strips and Sof-Lex polishing discs (p>0.05). The highest ΔE and R(a) values were obtained from Grandio (pGrandio presented the highest surface roughness and staining susceptibility after storage in coffee solution. Aelite Aesthetic Enamel, which did not include TEGDMA in its composition, showed the least discoloration. The composites with smaller filler size did not necessarily show low surface roughness and discoloration. Staining of composite resins was dependent on monomer structure, as well as surface irregularities. Copyright © 2012 Elsevier Ltd. All rights reserved.

  18. Modeling and Parameter Optimization for Surface Roughness and Residual Stress in Dry Turning Process

    Directory of Open Access Journals (Sweden)

    M. H. El-Axir

    2017-10-01

    Full Text Available The influence of some turning variables and tool overhang on surface roughness parameters and residual stress induced due to machining 6061-T6 aluminum alloy is investigated in this paper. Four input parameters (cutting speed, feed rate, depth of cut and tool overhang are considered. Tests are carried out by precision turning operation on a lathe. Design of experiment techniques, i.e. response surface methodology (RSM and Taguchi's technique have been used to accomplish the objective of the experimental study. Surface roughness parameters are measured using a portable surface roughness device while residual stresses are measured employing deflection-etching technique using electrochemical analysis. The results obtained reveal that feed and rotational speed play significant role in determining the average surface roughness. Furthermore, the depth of cut and tool overhang are less significant parameters, whereas tool overhang interacts with feed rate. The best result of surface roughness was obtained using low or medium values of overhang with low speed and /or feed rate. Minimum maximum tensile residual stress can be obtained with a combination of tool overhang of 37 mm with very low depth of cut, low rotational speed and feed rate of 0.188 mm/rev.

  19. Machining process influence on the chip form and surface roughness by neuro-fuzzy technique

    Science.gov (United States)

    Anicic, Obrad; Jović, Srđan; Aksić, Danilo; Skulić, Aleksandar; Nedić, Bogdan

    2017-04-01

    The main aim of the study was to analyze the influence of six machining parameters on the chip shape formation and surface roughness as well during turning of Steel 30CrNiMo8. Three components of cutting forces were used as inputs together with cutting speed, feed rate, and depth of cut. It is crucial for the engineers to use optimal machining parameters to get the best results or to high control of the machining process. Therefore, there is need to find the machining parameters for the optimal procedure of the machining process. Adaptive neuro-fuzzy inference system (ANFIS) was used to estimate the inputs influence on the chip shape formation and surface roughness. According to the results, the cutting force in direction of the depth of cut has the highest influence on the chip form. The testing error for the cutting force in direction of the depth of cut has testing error 0.2562. This cutting force determines the depth of cut. According to the results, the depth of cut has the highest influence on the surface roughness. Also the depth of cut has the highest influence on the surface roughness. The testing error for the cutting force in direction of the depth of cut has testing error 5.2753. Generally the depth of cut and the cutting force which provides the depth of cut are the most dominant factors for chip forms and surface roughness. Any small changes in depth of cut or in cutting force which provide the depth of cut could drastically affect the chip form or surface roughness of the working material.

  20. Influence of surface roughness on streptococcal adhesion forces to composite resins

    NARCIS (Netherlands)

    Mei, Li; Busscher, Henk J; van der Mei, Henny C; Ren, Yijin

    OBJECTIVE: To determine streptococcal adhesion forces with composite resins with different surface roughness. METHODS: Polishing and grinding were applied to obtain smooth (roughness 20 nm), moderately rough (150 nm) and rough (350 nm) surfaces of two orthodontic, light-cured composites. Adhesion

  1. Gloss and Surface Roughness of Anterior Pediatric Zirconia Crowns.

    Science.gov (United States)

    Theriot, Adrien L; Frey, Gary N; Ontiveros, Joe C; Badger, Gary

    2017-09-15

    The purpose of this study was to determine gloss and surface roughness (Ra) of pediatric anterior zirconia crowns. Gloss of labial and lingual surfaces of pediatric anterior zirconia crowns from three manufacturers was measured on 20 specimens using a small area gloss meter on each. Ra (μm) was measured using a contact-type surface profilometer. Data were evaluated by analysis of variance and pair-wise comparison at the 0.05 level of significance. There were statistically significant interactions between surface location and crown type for both gloss and Ra scores. NuSmile had higher mean gloss scores and lower mean Ra scores than both Kinder Krowns and EZCrowns. Kinder Krowns showed lower mean gloss scores and higher Ra scores than other crown groups. Among all crowns, there was a trend of higher mean gloss paired with lower mean surface roughness, and lower mean gloss paired with higher mean Ra. Hand smoothed followed by mechanically polished zirconia crowns (NuSmile) displayed the highest mean gloss and lowest mean Ra compared to hybrid polishedglazed zirconia crowns (Kinder Krowns, EZCrowns). Of the hybrid polished-glazed zirconia crowns, Kinder Krowns displayed the lowest mean gloss and highest mean Ra.

  2. Effect of whitening dentifrices on the surface roughness of a nanohybrid composite resin

    Science.gov (United States)

    da Rosa, Gabriela Migliorin; da Silva, Luciana Mendonça; de Menezes, Márcio; do Vale, Hugo Felipe; Regalado, Diego Ferreira; Pontes, Danielson Guedes

    2016-01-01

    Objectives: The present study verified the influence of whitening dentifrices on the surface roughness of a nanohybrid composite resin. Materials and Methods: Thirty-two specimens were prepared with Filtek™ Z350 XT (3M/ESPE) and randomly divided into four groups (n = 08) that were subjected to brushing simulation equivalent to the period of 1 month. The groups assessed were a control group with distilled water (G1), Colgate Total 12 Professional Clean (G2), Sensodyne Extra Whitener Extra Fresh (G3), and Colgate Luminous White (G4). A sequence of 90 cycles was performed for all the samples. The initial roughness of each group was analyzed by the Surface Roughness Tester (TR 200-TIME Group Inc., CA, USA). After the brushing period, the final roughness was measured, and the results were statistically analyzed using nonparametric Kruskal–Wallis and Dunn tests for intergroup roughness comparison in the time factor. For intragroup and “Δ Final − Initial” comparisons, the Wilcoxon test and (one-way) ANOVA were, respectively, performed (α = 0.05). Results: The roughness mean values before and after brushing showed no statistically significant difference when the different dentifrices were used. None of the dentifrices analyzed increased significantly the nanohybrid composite resin surface roughness in a 1 month of tooth brushing simulation. Conclusions: These results suggest that no hazardous effect on the roughness of nanohybrid composite resin can be expected when whitening dentifrices are used for a short period. Similar studies should be conducted to analyze other esthetic composite materials. PMID:27095891

  3. Effects of surface roughness and vortex generators on the LS(1)-0417MOD airfoil

    Energy Technology Data Exchange (ETDEWEB)

    Reuss, R.L.; Hoffman, M.J.; Gregorek, G.M. [Ohio State Univ., Columbus, OH (United States)

    1995-12-01

    An 18-inch constant-chord model of the LS(l)-0417MOD airfoil section was tested under two dimensional steady state conditions ate University 7{times}10 Subsonic Wind Tunnel. The objective was to document section lift and moment characteristics model and air flow conditions. Surface pressure data was acquired at {minus}60{degrees} through + 230{degrees} geometric angles of attack, at a nominal 1 million Reynolds number. Cases with and without leading edge grit roughness were investigated. The leading edge mulated blade conditions in the field. Additionally, surface pressure data were acquired for Reynolds numbers of 1.5 and 2.0 million, with and without leading edge grit roughness; the angle of attack was limited to a {minus}20{degrees} to 40{degrees} range. In general, results showed lift curve slope sensitivities to Reynolds number and roughness. The maximum lift coefficient was reduced as much as 29% by leading edge roughness. Moment coefficient showed little sensitivity to roughness beyond 50{degrees} angle of attack, but the expected decambering effect of a thicker boundary layer with roughness did show at lower angles. Tests were also conducted with vortex generators located at the 30% chord location on the upper surface only, at 1 and 1.5 million Reynolds numbers, with and without leading edge grit roughness. In general, with leading edge grit roughness applied, the vortex generators restored 85 percent of the baseline level of maximum lift coefficient but with a more sudden stall break and at a higher angle of attack than the baseline.

  4. Stability analysis of rough surfaces in adhesive normal contact

    Science.gov (United States)

    Rey, Valentine; Bleyer, Jeremy

    2018-03-01

    This paper deals with adhesive frictionless normal contact between one elastic flat solid and one stiff solid with rough surface. After computation of the equilibrium solution of the energy minimization principle and respecting the contact constraints, we aim at studying the stability of this equilibrium solution. This study of stability implies solving an eigenvalue problem with inequality constraints. To achieve this goal, we propose a proximal algorithm which enables qualifying the solution as stable or unstable and that gives the instability modes. This method has a low computational cost since no linear system inversion is required and is also suitable for parallel implementation. Illustrations are given for the Hertzian contact and for rough contact.

  5. Surface roughness and hardness of a composite resin: influence of finishing and polishing and immersion methods

    Directory of Open Access Journals (Sweden)

    Ana Luísa Botta Martins de Oliveira

    2010-09-01

    Full Text Available This study evaluated the finishing and polishing effect on the surface roughness and hardness of the Filtek Supreme XT, in fluoride solutions. Specimens were prepared (n = 140 with half of the samples finished and polished with Super-Snap® disks. The experimental groups were divided according to the presence or absence of finishing and polishing and immersion solutions (artificial saliva, sodium fluoride solution at 0.05% - manipulated, Fluordent Reach, Oral B, Fluorgard. The specimens remained immersed in artificial saliva for 24 hours and were then subjected to initial analysis (baseline of surface roughness and Vickers microhardness. Next, they were immersed in different fluoride solutions for 1 min/day, for 60 days. Afterwards, a new surface roughness and microhardness reading was conducted. The data were submitted to a two-way ANOVA and Tukey's test (5% significance level. For the comparison of mean roughness and hardness at baseline and after 60 days, the paired Student t test was used. The results showed that the surface roughness and microhardness of the Filtek Supreme XT were influenced by the finishing and polishing procedure, independently of the immersion methods.

  6. Effect of nanofiller on wear resistance and surface roughness of resin composites.

    Science.gov (United States)

    Han, Jian Min; Lin, Hong; Zheng, Gang; Shinya, Akiyoshi; Gomi, Harunori; Shinya, Akikazu; Lin, Jie

    2012-01-01

    To compare the wear resistance and surface roughness of nanofiller-containing composites and microhybrid composites after simulated wear. Five microhybrid composites and five nanofiller-containing resin composites were included in the study. Six cylindrical specimens with a diameter of 10 mm and a thickness of 6 mm for each material were prepared. The volume loss, vertical loss and the surface roughness (Ra) were determined after 800 cycles of simulated chewing motion. One specimen of each material was analysed by scanning electron microscopy (SEM) to compare the morphology of the wear surfaces. The microhybrid composites group and nanofiller-containing composites group were tested using the Mann-Whitney U test with a significance level of α = 0.05. For all microhybrid composites, the average wear volume loss and vertical loss were 56.44 mm3 and 730.6 µm, respectively, while the average wear losses of nanofiller-containing composites were 40.15 mm3 and 528.17 µm, respectively. The nanofiller containing composite GNH400N showed the least roughness (Ra = 0.346 ± 0.076 µm), while the conventional microhybrid composite Ceramage showed the highest roughness (Ra = 0.699 ± 0.214 µm). However, wear resistance and surface roughness for the two groups showed no statistical difference. SEM micrographs of the nanofiller-containing composites after wear testing showed smoother and more uniform wear surfaces than for the microhybrid composites. Nanofillers did not significantly influence the wear resistance of resin composites, but might improve the surface roughness of resin composites.

  7. Surface roughness comparison of methacrylate and silorane-based composite resins after 40% hydrogen peroxide application

    Directory of Open Access Journals (Sweden)

    Rori Sasmita

    2018-01-01

    Full Text Available The change of the tooth colour could be restored with bleaching. The tooth bleaching will affects the surface roughness of the composite resins. Recently, the material basis for composite resins has developed, among others are methacrylate-based and silorane based composite resins. The objective of this study was to distinguish the surface roughness value of methacrylate-based composite resin and silorane based composite resins. This research was quasi-experimental. The sample used in this study were methacrylate and silorane based composite resins in discs form, with the size of 6 mm and the thickness of 3 mm, manufactured into 20 specimens and divided into 2 groups. The control group was immersed in the artificial saliva, and the treatment group was applied with 40% hydrogen peroxide. The result of the experiment analyzed using unpaired sample t-test showed significant differences in the average value of the surface roughness after the application of 40% hydrogen peroxide. The average value of methacrylate and silorane based composite resins were 2.744 μm and 3.417 μm, respectively. There was a difference in the surface roughness of methacrylate and silorane based composite resin compounds after the application of 40% hydrogen peroxide. The surface roughness value of the silorane-based composite resin was higher than the methacrylate-based.

  8. Vortex shedding and morphodynamic response of bed surfaces containing non-erodible roughness elements

    Science.gov (United States)

    McKenna Neuman, Cheryl; Sanderson, Robert Steven; Sutton, Stephen

    2013-09-01

    A series of wind tunnel experiments was carried out to investigate particle entrainment from surfaces in which one or more roughness elements were embedded. Thin sand strips were employed to eliminate impact and ejection, and thus isolate entrainment by fluid drag. The pattern of erosion is consistent with the presence of coherent vortices, inclusive of trailing vortices in the wake flow. The shape and orientation of the roughness element strongly influence this pattern. When an upwind supply of saltators is introduced, the majority of particles within the bed are entrained through impact, with the exception of a sand tail to the lee of the roughness element. That is, the effect of coherent structures within the airflow, as related to spatial variation in the fluid drag exerted on the bed surface, is completely overprinted by the saltation cloud and the blocking of particle trajectories by the upwind face of the roughness element. In a repeated set of experiments, the bed was allowed to fully adjust its morphology to the transport system. In this case, particle entrainment did not selectively occur within the zone of wake flow, and by inference the fluid stress across the test surface appeared to be uniform. These experiments support the hypothesis that vortex annihilation occurs on morphodynamically adjusted surfaces. In summary, the system response to the emergence of non-erodible roughness elements on surfaces affected by wind erosion involves a suite of geophysical processes, each of which attains varied levels of dominance within a given morphodynamic domain.

  9. Sputtering of rough surfaces: a 3D simulation study

    Science.gov (United States)

    von Toussaint, U.; Mutzke, A.; Manhard, A.

    2017-12-01

    The lifetime of plasma-facing components is critical for future magnetic confinement fusion power plants. A key process limiting the lifetime of the first-wall is sputtering by energetic ions. To provide a consistent modeling of the sputtering process of realistic geometries, the SDTrimSP-code has been extended to enable the processing of analytic as well as measured arbitrary 3D surface morphologies. The code has been applied to study the effect of varying the impact angle of ions on rough surfaces on the sputter yield as well as the influence of the aspect ratio of surface structures on the 2D distribution of the local sputtering yields. Depending on the surface morphologies reductions of the effective sputter yields to less than 25% have been observed in the simulation results.

  10. Anisotropic spreading of liquid metal on a rough intermetallic surface

    Directory of Open Access Journals (Sweden)

    Liu Wen

    2011-01-01

    Full Text Available An anisotropic wicking of molten Sn-Pb solder over an intermetallic rough surface has been studied. The phenomenon features preferential spreading and forming of an elliptical spread domain. A theoretically formulated model was established to predict the ratio of the wicking distance along the long axis (rx to that along the short axis (ry of the final wicking pattern. The phenomenon was simultaneously experimentally observed and recorded with a hotstage microscopy technique. The anisotropic wicking is established to be caused by a non-uniform topography of surface micro structures as opposed to an isotropic wicking on an intermetallic surface with uniformly distributed surface micro features. The relative deviation between the theoretically predicted rx/ry ratio and the corresponding average experimental value is 5%. Hence, the small margin of error confirms the validity of the proposed theoretical model of anisotropic wicking.

  11. Influence of surface roughness on the friction property of textured surface

    OpenAIRE

    Yuankai Zhou; Hua Zhu; Wenqian Zhang; Xue Zuo; Yan Li; Jianhua Yang

    2015-01-01

    In contrast with dimple textures, surface roughness is a texture at the micro-scale, essentially which will influence the load-bearing capacity of lubricant film. The numerical simulation was carried out to investigate the influence of surface roughness on friction property of textured surface. The lubricant film pressure was obtained using the method of computational fluid dynamics according to geometric model of round dimple, and the renormalization-group k–ε turbulent model was adopted in ...

  12. Surface roughness of composite resin veneer after application of herbal and non-herbal toothpaste

    Science.gov (United States)

    Nuraini, S.; Herda, E.; Irawan, B.

    2017-08-01

    The aim of this study was to find out the surface roughness of composite resin veneer after brushing. In this study, 24 specimens of composite resin veneer are divided into three subgroups: brushed without toothpaste, brushed with non-herbal toothpaste, and brushed with herbal toothpaste. Brushing was performed for one set of 5,000 strokes and continued for a second set of 5,000 strokes. Roughness of composite resin veneer was determined using a Surface Roughness Tester. The results were statistically analyzed using Kruskal-Wallis nonparametric test and Post Hoc Mann-Whitney. The results indicate that the highest difference among the Ra values occurred within the subgroup that was brushed with the herbal toothpaste. In conclusion, the herbal toothpaste produced a rougher surface on composite resin veneer compared to non-herbal toothpaste.

  13. Surface Roughness and Gloss of Actual Composites as Polished With Different Polishing Systems.

    Science.gov (United States)

    Rodrigues-Junior, S A; Chemin, P; Piaia, P P; Ferracane, J L

    2015-01-01

    This in vitro study evaluated the effect of polishing with different polishing systems on the surface roughness and gloss of commercial composites. One hundred disk-shaped specimens (10 mm in diameter × 2 mm thick) were made with Filtek P-90, Filtek Z350 XT, Opallis, and Grandio. The specimens were manually finished with #400 sandpaper and polished by a single operator using three multistep systems (Superfix, Diamond Pro, and Sof-lex), one two-step system (Polidores DFL), and one one-step system (Enhance), following the manufacturer's instructions. The average surface roughness (μm) was measured with a surface profilometer (TR 200 Surface Roughness Tester), and gloss was measured using a small-area glossmeter (Novo-Curve, Rhopoint Instrumentation, East Sussex, UK). Data were analyzed by two-way analysis of variance and Tukey's test (α=0.05). Statistically significant differences in surface roughness were identified by varying the polishing systems (pGrandio when polished with Sof-Lex and Filtek Z250 and Opallis when polished with Enhance. Gloss was influenced by the composites (p<0.0001), the polishing systems (p<0.0001), and the interaction between them (p<0.0001). The one-step system, Enhance, produced the lowest gloss for all composites. Surface roughness and gloss were affected by composites and polishing systems. The interaction between both also influenced these surface characteristics, meaning that a single polishing system will not behave similarly for all composites. The multistep systems produced higher gloss, while the one-step system produced the highest surface roughness and the lowest gloss of all.

  14. Modelling of local carbon deposition on rough test limiter exposed to the edge plasma of TEXTOR

    International Nuclear Information System (INIS)

    Dai Shuyu; Sun Jizhong; Wang Dezhen; Kirschner, A.; Matveev, D.; Borodin, D.; Bjoerkas, C.

    2013-01-01

    A Monte-Carlo code called SURO has been developed to study the influence of surface roughness on the impurity deposition characteristic in fusion experiments. SURO uses the test particle approach to describe the impact of background plasma and the deposition of impurity particles on a sinusoidal surface. The local impact angle and dynamic change of surface roughness as well as surface concentrations of different species due to erosion and deposition are taken into account. Coupled with 3D Monte-Carlo code ERO, SURO was used to study the impact of surface roughness on 13 C deposition in 13 CH 4 injection experiments in TEXTOR. The simulations showed that the amount of net deposited 13 C species increases with surface roughness. Parameter studies with varying 12 C and 13 C fluxes were performed to gain insight into impurity deposition characteristic on the rough surface. Calculations of the exposure time needed for surface smoothing for TEXTOR and ITER were also carried out for different scenarios. (author)

  15. Subgap in the Surface Bound States Spectrum of Superfluid ^3 He-B with Rough Surface

    Science.gov (United States)

    Nagato, Y.; Higashitani, S.; Nagai, K.

    2017-12-01

    The subgap structure in the surface bound states spectrum of superfluid ^3 He-B with rough surface is discussed. The subgap is formed by the level repulsion between the surface bound state and the continuum states in the course of multiple scattering by the surface roughness. We show that the level repulsion is originated from the nature of the wave function of the surface bound state that is now recognized as Majorana fermion. We study the superfluid ^3 He-B with a rough surface and in a magnetic field perpendicular to the surface using the quasi-classical Green function together with a random S-matrix model. We calculate the self-consistent order parameters, the spin polarization density and the surface density of states. It is shown that the subgap is found also in a magnetic field perpendicular to the surface. The magnetic field dependence of the transverse acoustic impedance is also discussed.

  16. The influence of mouthrinses and simulated toothbrushing on the surface roughness of a nanofilled composite resin

    Directory of Open Access Journals (Sweden)

    Keico Graciela Sano Trauth

    2012-06-01

    Full Text Available The aim of this study was to determine the influence of mouthrinses on the surface roughness of a nanofilled composite resin after toothbrushing. One hundred nanofilled composite resin specimens were prepared and randomly distributed into two groups-brushed and non-brushed-and then assigned to five subgroups, according to the mouthrinse solutions (n = 10: Colgate Plax Fresh Mint, Oral B, Cepacol, Colgate Plax, and artificial saliva. Each sample was immersed in 20 mL of the mouthrinses for 1 minute, 5 days per week, twice a day, for a 3-week period. The control group used in the study was one in which the specimens were not subjected to brushing and remained only in artificial saliva. Toothbrushing was performed once a week for 1 minute, for 3 weeks. Surface roughness measurements (Ra were performed after the immersion period and toothbrushing, by means of a profilometer. Data were analyzed by two-way ANOVA and Tukey's test. Analysis revealed that the association between toothbrushing and Colgate Plax Fresh Mint produced the lowest surface roughness (p < 0.05. All other groups tested (Oral B, Cepacol, Colgate Plax, artificial saliva exhibited no statistically significant differences between surfaces, whether subjected to toothbrushing or not (p < 0.05. It was concluded that the surface roughness of the nanofilled composite resin tested can be influenced by the mouthrinse associated with toothbrushing.

  17. Effects of bridge cable surface roughness and cross-sectional distortion on aerodynamic force coefficients

    DEFF Research Database (Denmark)

    Matteoni, G.; Georgakis, C.T.

    2012-01-01

    of their inherent surface roughness and shape, which might present a significant disturbance for the surrounding wind flow. The present study focuses on the experimental determination, based on static wind tunnel tests, of the aerodynamic coefficients of full-scale bridge cable section models both perpendicular...

  18. Heat transfer and friction on smooth and rough test rods

    International Nuclear Information System (INIS)

    Franken, W.M.P.; Hoogland, H.; Deijman, P.

    1977-06-01

    Results are reported on heat transfer and pressure drop tests on one smooth and nine rough test rods in an annular geometry. The wall roughness consisted of transversal ribs with various roughness pitches, rib heights and rib widths. The tests were performed with air as coolant under a wide range of experimental conditions: 10 5 5 , 1.1 2. Special attention has been given to the effect of variation of the physical coolant properties over the flow cross section. This effect could be described by the power function (Tsub(w)/Tsub(b))sup(-0.3l) in additional systematic variation of the heat transfer could be recognized, dependent on the coolant temperature level. The experimental results were correlated by the equation St = C(Tsub(in)) Resup(-0.2) Prsup(-0.6) (Tsub(w)/Tsub(b)sup(-0.31). Values of C(Tsub(in)) are given in tabular form. The thermal entrance effect has been measured on various test rods. A substantial reduction of the heat transfer coefficient was almost constant along the rough test rods

  19. Influence of surface roughness on the friction property of textured surface

    Directory of Open Access Journals (Sweden)

    Yuankai Zhou

    2015-02-01

    Full Text Available In contrast with dimple textures, surface roughness is a texture at the micro-scale, essentially which will influence the load-bearing capacity of lubricant film. The numerical simulation was carried out to investigate the influence of surface roughness on friction property of textured surface. The lubricant film pressure was obtained using the method of computational fluid dynamics according to geometric model of round dimple, and the renormalization-group k–ε turbulent model was adopted in the computation. The numerical simulation results suggest that there is an optimum dimensionless surface roughness, and near this value, the maximum load-bearing capacity can be achieved. The load-bearing capacity is determined by the surface texture, the surface roughness, and the interaction between them. To get information of friction coefficient, the experiments were conducted. This experiment was used to evaluate the simulation. The experimental results show that for the frequency of 4 and 6 Hz, friction coefficient decreases at first and then increases with decreasing surface roughness, which indicates that there exists the optimum region of surface roughness leading to the best friction reduction effect, and it becomes larger when area fractions increase from 2% to 10%. The experimental results agree well with the simulation results.

  20. Surface Roughness of Composite Resins after Simulated Toothbrushing with Different Dentifrices.

    Science.gov (United States)

    Monteiro, Bruna; Spohr, Ana Maria

    2015-07-01

    The aim of the study was to evaluate, in vitro, the surface roughness of two composite resins submitted to simulated toothbrushing with three different dentifrices. Totally, 36 samples of Z350XT and 36 samples of Empress Direct were built and randomly divided into three groups (n = 12) according to the dentifrice used (Oral-B Pro-Health Whitening [OBW], Colgate Sensitive Pro-Relief [CS], Colgate Total Clean Mint 12 [CT12]). The samples were submitted to 5,000, 10,000 or 20,000 cycles of simulated toothbrushing. After each simulated period, the surface roughness of the samples was measured using a roughness tester. According to three-way analysis of variance, dentifrice (P = 0.044) and brushing time (P = 0.000) were significant. The composite resin was not significant (P = 0.381) and the interaction among the factors was not significant (P > 0.05). The mean values of the surface roughness (µm) followed by the same letter represent no statistical difference by Tukey's post-hoc test (P composite resins. The dentifrice OBW caused a higher surface roughness in both composite resins.

  1. Comparative evaluation of effect of different polishing systems on surface roughness of composite resin: An in vitro study.

    Science.gov (United States)

    Chour, Rashmi G; Moda, Aman; Arora, Arpana; Arafath, Muhmmed Y; Shetty, Vikram K; Rishal, Yousef

    2016-08-01

    Satisfactory composite restoration depends upon its smooth finish, quality of polishing agents, type of composite material used, and its composition. The present study evaluated the effect of different polishing systems on the surface roughness of composite resin. Forty discs of composite were prepared and equally subjected to different finishing and polishing procedures; (i) unpolished control group, (ii) sof-lex discs, (iii) diamond tips, and (iv) Astrobrush groups. Later, the surface roughness for the entire specimen was evaluated using Profilomotor. Data were tabulated and statistically analyzed using analysis of variance and Tukey's test at significance level of 0.001. Composite surface roughness after polishing was statistically significant between the groups. Sof-lex group produced lesser surface roughness compared to control, Astrobrush, and diamond group. The present study indicated that diamond tips can be used to remove rough surface whereas sof-lex can be used for final finish and polish of the composite restoration.

  2. On the nature of surface roughness with application to contact mechanics, sealing, rubber friction and adhesion

    International Nuclear Information System (INIS)

    Persson, B N J; Albohr, O; Tartaglino, U; Volokitin, A I; Tosatti, E

    2005-01-01

    Surface roughness has a huge impact on many important phenomena. The most important property of rough surfaces is the surface roughness power spectrum C(q). We present surface roughness power spectra of many surfaces of practical importance, obtained from the surface height profile measured using optical methods and the atomic force microscope. We show how the power spectrum determines the contact area between two solids. We also present applications to sealing, rubber friction and adhesion for rough surfaces, where the power spectrum enters as an important input. (topical review)

  3. Effect of denture cleansers on metal ion release and surface roughness of denture base materials.

    Science.gov (United States)

    Davi, Letícia Resende; Felipucci, Daniela Nair Borges; de Souza, Raphael Freitas; Bezzon, Osvaldo Luiz; Lovato-Silva, Cláudia Helena; Pagnano, Valéria Oliveira; Paranhos, Helena de Freitas Oliveira

    2012-01-01

    Chemical disinfectants are usually associated with mechanical methods to remove stains and reduce biofilm formation. This study evaluated the effect of disinfectants on release of metal ions and surface roughness of commercially pure titanium, metal alloys, and heat-polymerized acrylic resin, simulating 180 immersion trials. Disk-shaped specimens were fabricated with commercially pure titanium (Tritan), nickel-chromium-molybdenum-titanium (Vi-Star), nickel-chromium (Fit Cast-SB Plus), and nickel-chromium-beryllium (Fit Cast-V) alloys. Each cast disk was invested in the flasks, incorporating the metal disk to the heat-polymerized acrylic resin. The specimens (n=5) were immersed in these solutions: sodium hypochlorite 0.05%, Periogard, Cepacol, Corega Tabs, Medical Interporous, and Polident. Deionized water was used as a control. The quantitative analysis of metal ion release was performed using inductively coupled plasma mass spectrometry (ELAN DRC II). A surface analyzer (Surftest SJ-201P) was used to measure the surface roughness (µm). Data were recorded before and after the immersions and evaluated by two-way ANOVA and Tukey's test (α=0.05). The nickel release proved most significant with the Vi-Star and Fit Cast-V alloys after immersion in Medical Interporous. There was a significant difference in surface roughness of the resin (p=0.011) after immersion. Cepacol caused significantly higher resin roughness. The immersion products had no influence on metal roughness (p=0.388). It could be concluded that the tested alloys can be considered safe for removable denture fabrication, but disinfectant solutions as Cepacol and Medical Interporous tablet for daily denture immersion should be used with caution because it caused greater resin surface roughness and greater ion release, respectively.

  4. Surface roughness: A review of its measurement at micro-/nano-scale

    Science.gov (United States)

    Gong, Yuxuan; Xu, Jian; Buchanan, Relva C.

    2018-01-01

    The measurement of surface roughness at micro-/nano-scale is of great importance to metrological, manufacturing, engineering, and scientific applications given the critical roles of roughness in physical and chemical phenomena. The surface roughness of materials can significantly change the way of how they interact with light, phonons, molecules, and so forth, thus surface roughness ultimately determines the functionality and property of materials. In this short review, the techniques of measuring micro-/nano-scale surface roughness are discussed with special focus on the limitations and capabilities of each technique. In addition, the calculations of surface roughness and their theoretical background are discussed to offer readers a better understanding of the importance of post-measurement analysis. Recent progress on fractal analysis of surface roughness is discussed to shed light on the future efforts in surface roughness measurement.

  5. Effects of surface inactivation, high temperature drying and preservative treatment on surface roughness and colour of alder and beech wood

    Science.gov (United States)

    Aydin, Ismail; Colakoglu, Gursel

    2005-10-01

    Although extensive research has been conducted in wood surface quality analysis, a unified approach to surface quality characterisation does not exist. Measurements of the variation in surface roughness and surface colour are used widely for the evaluation of wood surface quality. Colour is a basic visual feature for wood and wood-based products. Colour measurement is one of the quality control tests that should be carried out because the colour deviations are spotted easily by the consumers. On the other hand, a common problem faced by plywood manufacturers is panel delamination, for which a major cause is poor quality glue-bonds resulting from rough veneer. Rotary cut veneers with dimensions of 500 mm × 500 mm × 2 mm manufactured from alder ( Alnus glutinosa subsp. barbata) and beech ( Fagus orientalis Lipsky) logs were used as materials in this study. Veneer sheets were oven-dried in a veneer dryer at 110 °C (normal drying temperature) and 180 °C (high drying temperature) after peeling process. The surfaces of some veneers were then exposed at indoor laboratory conditions to obtain inactive wood surfaces for glue bonds, and some veneers were treated with borax, boric acid and ammonium acetate solutions. After these treatments, surface roughness and colour measurements were made on veneer surfaces. High temperature drying process caused a darkening on the surfaces of alder and beech veneers. Total colour change value (Δ E*) increased linear with increasing exposure time. Among the treatment solutions, ammonium acetate caused the biggest colour change while treatment with borax caused the lowest changes in Δ E* values. Considerable changes in surface roughness after preservative treatment did not occur on veneer surfaces. Generally, no clear changes were obtained or the values mean roughness profile ( Ra) decreased slightly in Ra values after the natural inactivation process.

  6. Surface Roughness effects on Runoff and Soil Erosion Rates Under Simulated Rainfall

    Science.gov (United States)

    Soil surface roughness is identified as one of the controlling factors governing runoff and soil loss yet, most studies pay little attention to soil surface roughness. In this study, we analyzed the influence of random soil surface roughness on runoff and soil erosion rates. Bulk samples of a silt l...

  7. The measurement of surface roughness to determine the suitability of different methods for stone cleaning

    International Nuclear Information System (INIS)

    Vazquez-Calvo, Carmen; Alvarez de Buergo, Monica; Fort, Rafael; Varas-Muriel, Maria Jose

    2012-01-01

    The roughness of stone surface was measured, before and after bead blasting-based cleaning methods, to select the most efficient one to be used in masonry and stonework of specific areas of the Cathedral of Segovia (Spain). These types of cleaning methods can, besides the removal of soiling and surface deposits, leave a rougher surface, which would mean higher and more rapid water retention and deposit accumulation due to a specific surface increase, therefore accelerating stone decay. Or, in contrast, the cleaning method can be so aggressive that it can smooth the surface by reducing its roughness, a fact that usually corresponds to excessive material removal—soot and deposits–-but also part of the stone substrate. Roughness results were complemented with scanning electron microscopy observations and analyses and colour measurements. Finally, it was possible to select the best cleaning method among the six that were analysed, for different areas and different stone materials. Therefore, this study confirms the measurement of surface roughness as a reliable test to determine the suitability of stone cleaning methods; it is a non-destructive technique, portable and friendly to use, which can help us to rapidly assess—together with other techniques—the efficacy and aggressiveness of the stone cleaning method. (paper)

  8. The effect of milling and postmilling procedures on the surface roughness of CAD/CAM materials.

    Science.gov (United States)

    Mota, Eduardo Gonçalves; Smidt, Laura Nunes; Fracasso, Lisiane Martins; Burnett, Luiz Henrique; Spohr, Ana Maria

    2017-11-12

    The aim of this study was to evaluate the surface roughness and analyze the surface topography of five different CAD/CAM ceramics and one CAD/CAM composite resin for CEREC after milling and postmilling procedures. Blocks of the ceramics Mark II, IPS Empress CAD, IPS e.max CAD, Suprinity and Enamic, and blocks of the composite resin Lava Ultimate were milled at CEREC MCXL. Ten flat samples of each material were obtained. The surface roughness (Ra) test was performed before and after milling, crystallization, polishing, and glaze when indicated, followed by SEM and AFM analysis. Data were submitted to one-way ANOVA with repeated measures and the Tukey HSD test (α = 0.05). The milling step significantly increased the roughness of all the tested materials (P CAD and Suprinity) were more suitable to roughness than the other tested materials (P CAD/CAM materials, that is, fully sintered, should be only hand polished. The glaze step can be suppressed resulting in time saving. However, the glaze step in soft-milling lithium disilicate is imperative. © 2017 Wiley Periodicals, Inc.

  9. Surface roughness studies with DALLAS-detector array for laser light angular scattering

    Science.gov (United States)

    Vorburger, T. V.; Teague, E. C.; Scire, F. E.; Mclay, M. J.; Gilsinn, D. E.

    1984-01-01

    An attempt is made to develop a better mathematical description of optical scattering phenomena, in order to construct an optical scattering apparatus for reliable and routine measurements of roughness parameters without resorting to comparator standards. After a brief outline of optical scattering theory, a description is presented of an experimental instrument for measuring surface roughness which incorporates optical scattering principles. The instrument has a He-Ne laser which illuminates the test surface at a variable angle of incidence. Scattered light distribution is detected by an array of 87 fiber-optic sensors positioned in a rotating semicircular yoke. The output from the detector is digitized and analyzed in a laboratory computer. For a comparison with experimental data, theoretical distributions are calculated by substituting the roughness profiles into the operand of and integral equation for electromagnetic scattering developed by Beckmann and Spizzichino (1963). A schematic diagram of the instrument is provided and the general implications of the experimental results are discussed.

  10. A facile method for simulating randomly rough membrane surface associated with interface behaviors

    Science.gov (United States)

    Qu, Xiaolu; Cai, Xiang; Zhang, Meijia; Lin, Hongjun; Leihong, Zhao; Liao, Bao-Qiang

    2018-01-01

    Modeling rough surfaces has emerged as a distinct discipline of considerable research interest in interface behaviors including membrane fouling. In this paper, a facile method was proposed to simulate rough membrane surface morphology. Natural membrane surface was found to be randomly rough, and its height distribution obeys Gaussian distribution. A new method which combines spectrum method, Gaussian distribution and Fourier transform technique was deduced. Simulation of the rough membrane surface showed high similarity in terms of statistical roughness and height distribution between the simulated surface and the real membrane surface, indicating feasibility of the new method. It was found that, correlation length (l) and the number of superposed ridges (N) are key parameters affecting the simulated membrane surface morphology. This new method has evident advantages over conventional modeling methods The proposed method for randomly rough membrane surface modeling could be potentially used to quantify the interfacial interactions between two rough surfaces, giving implications for membrane fouling mitigation.

  11. Growth of contact area between rough surfaces under normal stress

    Science.gov (United States)

    Stesky, R. M.; Hannan, S. S.

    1987-05-01

    The contact area between deforming rough surfaces in marble, alabaster, and quartz was measured from thin sections of surfaces bonded under load with low viscosity resin epoxy. The marble and alabaster samples had contact areas that increased with stress at an accelerating rate. This result suggests that the strength of the asperity contacts decreased progressively during the deformation, following some form of strain weakening relationship. This conclusion is supported by petrographic observation of the thin sections that indicate that much of the deformation was cataclastic, with minor twinning of calcite and kinking of gypsum. In the case of the quartz, the observed contact area was small and increased approximately linearly with normal stress. Only the irreversible cataclastic deformation was observed; however strain-induced birefringence and cracking of the epoxy, not observed with the other rocks, suggests that significant elastic deformation occurred, but recovered during unloading.

  12. Statistical Analysis of Magnetic Abrasive Finishing (MAF) On Surface Roughness

    Science.gov (United States)

    Givi, Mehrdad; Tehrani, Alireza Fadaei; Mohammadi, Aminollah

    2010-06-01

    Magnetic assisted finishing is one of the nontraditional methods of polishing that recently has been attractive for the researchers. This paper investigates the effects of some parameters such as rotational speed of the permanent magnetic pole, work gap between the permanent pole and the work piece, number of the cycles and the weight of the abrasive particles on aluminum surface plate finishing. The three levels full factorial method was used as the DOE technique (design of experiments) for studying the selected factors. Analysis of Variance (ANOVA) has been used to determine significant factors and also to obtain an equation based on data regression. Experimental results indicate that for a change in surface roughness ΔRa, number of cycles and working gap are found to be the most significant parameters followed by rotational speed and then weight of powders.

  13. Effect of Soft Drinks and Fresh Fruit Juice on Surface Roughness of Commonly used Restorative Materials.

    Science.gov (United States)

    Maganur, Prabhadevi; Satish, V; Prabhakar, A R; Namineni, Srinivas

    2015-01-01

    In this in vitro study, the effects of a Cola drink, and fresh fruit juice (citrus) on the surface roughness on flowable composite and resin-modified glass ionomer cement (RMGIC) each was evaluated and compared. Using a brass mold 70 pellets each of flowable composite (Filtek™ Flow) and RMGIC tricure restorative material were prepared according to the manufacturer's instructions. Two groups (groups I and II) were formed containing 30 pellets of each material. Remaining 10 pellets of each restorative material did form the control group [water (group III)]. Experimental group pellets were again divided into three subgroups (mild, moderate and severe) containing 10 pellets each and were kept in plastic containers with 30 ml Cola drink (group I) and fresh fruit juice (group II) respectively. Immersion regime was followed according to M aupome G et al. Baseline and final surface roughness (Ra) value for each pellet was evaluated using a profilometer. Statistical analysis was done with Wilcoxon's signed rank test and analysis of variance (ANOVA) followed by Mann-Whitney test. Results showed that the erosive effect of both Cola drink and fresh fruit juice caused significant surface roughness on both flowable composite and RMGIC restorative materials in the mild, moderate and severe immersion regimes. How to cite this article: Maganur P, Satish V, Prabhakar AR, Namineni S. Effect of Soft Drinks and Fresh Fruit Juice on Surface Roughness of Commonly used Restorative Materials. Int J Clin Pediatr Dent 2015;8(1):1-5.

  14. Bacterial Adhesion and Surface Roughness for Different Clinical Techniques for Acrylic Polymethyl Methacrylate.

    Science.gov (United States)

    Dantas, Lucas Costa de Medeiros; da Silva-Neto, João Paulo; Dantas, Talita Souza; Naves, Lucas Zago; das Neves, Flávio Domingues; da Mota, Adérito Soares

    2016-01-01

    This study sought to assess the effect of different surface finishing and polishing protocols on the surface roughness and bacterial adhesion (S. sanguinis) to polymethyl methacrylates (PMMA). Fifty specimens were divided into 5 groups (n = 10) according to their fabrication method and surface finishing protocol: LP (3 : 1 ratio and laboratory polishing), NF (Nealon technique and finishing), NP (Nealon technique and manual polishing), MF (3 : 1 ratio and manual finishing), and MP (3 : 1 ratio and manual polishing). For each group, five specimens were submitted to bacterial adhesion tests and analyzed by scanning electron microscopy (SEM). Two additional specimens were subjected to surface topography analysis by SEM and the remaining three specimens were subjected to surface roughness measurements. Data were compared by one-way ANOVA. The mean bacterial counts were as follows: NF, 19.6 ± 3.05; MP, 5.36 ± 2.08; NP, 4.96 ± 1.93; MF, 7.36 ± 2.45; and LP, 1.56 ± 0.62 (CFU). The mean surface roughness values were as follows: NF, 3.23 ± 0.15; MP, 0.52 ± 0.05; NP, 0.60 ± 0.08; MF, 2.69 ± 0.12; and LP, 0.07 ± 0.02 (μm). A reduction in the surface roughness was observed to be directly related to a decrease in bacterial adhesion. It was verified that the laboratory processing of PMMA might decrease the surface roughness and consequently the adhesion of S. sanguinis to this material.

  15. Surface roughness and the flexural and bend strength of zirconia after different surface treatments.

    Science.gov (United States)

    Hjerppe, Jenni; Närhi, Timo O; Vallittu, Pekka K; Lassila, Lippo V J

    2016-10-01

    Different surface treatments are commonly used during the fabrication of zirconia fixed dental prostheses. However, such treatments can affect the properties of the zirconia framework material. The purpose of this in vitro study was to determine the effect of different surface treatments on the surface roughness and flexural and bend strength of zirconia. Seventy-two zirconia disks (n=8) and 72 zirconia bars (n=8) were sintered and divided into 9 groups for different surface treatments: sintered control, airborne-particle abraded with 50-μm aluminum oxide, airborne-particle abraded with Rocatec soft (30 μm), airborne-particle abraded with Rocatec (105 μm), grinding dry with a micromotor, turbine grinding under water cooling, grinding with silicon carbide paper, diamond paste polishing, and steam cleaning. The biaxial flexural strength of the disks (diameter 19 mm, thickness 1.6 mm) and 3-point bend test of the bars (thickness 2 mm, height 2 mm, length 25 mm) were measured dry at room temperature. One-way ANOVA followed by the Tukey HSD test (α=.05) and Pearson correlation test were used for statistical analysis. Airborne-particle abrasion and silicon carbide paper grinding increased the flexural and bend strength of zirconia specimens (Pzirconia framework material. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

  16. Multiscale Finite Element Methods for Flows on Rough Surfaces

    KAUST Repository

    Efendiev, Yalchin

    2013-01-01

    In this paper, we present the Multiscale Finite Element Method (MsFEM) for problems on rough heterogeneous surfaces. We consider the diffusion equation on oscillatory surfaces. Our objective is to represent small-scale features of the solution via multiscale basis functions described on a coarse grid. This problem arises in many applications where processes occur on surfaces or thin layers. We present a unified multiscale finite element framework that entails the use of transformations that map the reference surface to the deformed surface. The main ingredients of MsFEM are (1) the construction of multiscale basis functions and (2) a global coupling of these basis functions. For the construction of multiscale basis functions, our approach uses the transformation of the reference surface to a deformed surface. On the deformed surface, multiscale basis functions are defined where reduced (1D) problems are solved along the edges of coarse-grid blocks to calculate nodalmultiscale basis functions. Furthermore, these basis functions are transformed back to the reference configuration. We discuss the use of appropriate transformation operators that improve the accuracy of the method. The method has an optimal convergence if the transformed surface is smooth and the image of the coarse partition in the reference configuration forms a quasiuniform partition. In this paper, we consider such transformations based on harmonic coordinates (following H. Owhadi and L. Zhang [Comm. Pure and Applied Math., LX(2007), pp. 675-723]) and discuss gridding issues in the reference configuration. Numerical results are presented where we compare the MsFEM when two types of deformations are used formultiscale basis construction. The first deformation employs local information and the second deformation employs a global information. Our numerical results showthat one can improve the accuracy of the simulations when a global information is used. © 2013 Global-Science Press.

  17. Nanodrop on a smooth solid surface with hidden roughness. Density functional theory considerations

    Science.gov (United States)

    Berim, Gersh O.; Ruckenstein, Eli

    2015-04-01

    A nanodrop of a test fluid placed on a smooth surface of a solid material of nonuniform density which covers a rough solid surface (hidden roughness) is examined, on the basis of the density functional theory (DFT), in the presence of an external perturbative force parallel to the surface. The contact angles which the drop profile makes with the surface at the leading edges of the drop are determined as functions of drop size and perturbative external force. A critical sticking force, defined as the largest value of the perturbative force for which the drop remains at equilibrium, is determined and its dependence on the size of the drop is explained on the basis of the shape of the interaction potential generated by the solid in vicinity of the leading edges of the drop. For even larger values of the perturbative force no drop-like solution of the Euler-Lagrange equation of the DFT was found. The upper bound of the inclination angle of a surface containing a macroscopic drop is estimated on the basis of results obtained for nanodrops and some experimental results are interpreted. The main conclusion is that the hidden roughness has a similar effect on the drop features as the traditionally considered physical and chemical roughnesses.

  18. Enhancement of Friction against a Rough Surface by a Ridge-Channel Surface Microstructure.

    Science.gov (United States)

    Bai, Ying; Hui, Chung-Yuen; Levrard, Benjamin; Jagota, Anand

    2015-07-14

    We report on a study of the sliding friction of elastomeric surfaces patterned with ridges and channels (and unstructured flat controls), against both smooth and roughened spherical indenters. Against the smooth spherical indenter, all of the structured surfaces have highly reduced sliding friction due to the reduction in actual area of contact. Against roughened spherical indenters, however, the sliding force for structured samples can be up to 50% greater than that of an unstructured flat control. The mechanism of enhanced friction against a rough surface is due to a combination of increased actual area of contact, interlocking between roughness and the surface structure, and attendant dynamic instabilities that dissipate energy.

  19. In vitro evaluation of human dental enamel surface roughness bleached with 35% carbamide peroxide and submitted to abrasive dentifrice brushing

    Directory of Open Access Journals (Sweden)

    Worschech Claudia Cia

    2003-01-01

    Full Text Available The aim of this in vitro study was to evaluate the surface roughness of human enamel bleached with 35% carbamide peroxide at different times and submitted to different superficial cleaning treatments: G1 - not brushed; G2 - brushed with fluoride abrasive dentifrice; G3 - brushed with a non-fluoride abrasive dentifrice; G4 - brushed without dentifrice. Sixty fragments of human molar teeth with 4 x 4 mm were obtained using a diamond disc. The specimens were polished with sandpaper and abrasive pastes. A perfilometer was used to measure roughness average (Ra values of the initial surface roughness and at each 7-day-interval after the beginning of treatment. The bleaching was performed on the surface of the fragments for 1 hour a week, and the surface cleaning treatment for 3 minutes daily. The samples were stored in individual receptacles with artificial saliva. Analysis of variance and the Tukey test revealed significant differences in surface roughness values for G2 and G3, which showed an increase in roughness over time; G1 and G4 showed no significant roughness differences. The bleaching with 35% carbamide peroxide did not alter the enamel surface roughness, but when the bleaching treatment was performed combined with brushing with abrasive dentifrices, there was a significant increase in roughness values.

  20. An Investigation of the Influence of Initial Roughness on the Friction and Wear Behavior of Ground Surfaces.

    Science.gov (United States)

    Liang, Guoxing; Schmauder, Siegfried; Lyu, Ming; Schneider, Yanling; Zhang, Cheng; Han, Yang

    2018-02-04

    Friction and wear tests were performed on AISI 1045 steel specimens with different initial roughness parameters, machined by a creep-feed dry grinding process, to study the friction and wear behavior on a pin-on-disc tester in dry sliding conditions. Average surface roughness (Ra), root mean square (Rq), skewness (Rsk) and kurtosis (Rku) were involved in order to analyse the influence of the friction and wear behavior. The observations reveal that a surface with initial roughness parameters of higher Ra, Rq and Rku will lead to a longer initial-steady transition period in the sliding tests. The plastic deformation mainly concentrates in the depth of 20-50 μm under the worn surface and the critical plastic deformation is generated on the rough surface. For surfaces with large Ra, Rq, low Rsk and high Rku values, it is easy to lose the C element in, the reciprocating extrusion.

  1. An Investigation of the Influence of Initial Roughness on the Friction and Wear Behavior of Ground Surfaces

    Science.gov (United States)

    Liang, Guoxing; Schmauder, Siegfried; Lyu, Ming; Schneider, Yanling; Zhang, Cheng; Han, Yang

    2018-01-01

    Friction and wear tests were performed on AISI 1045 steel specimens with different initial roughness parameters, machined by a creep-feed dry grinding process, to study the friction and wear behavior on a pin-on-disc tester in dry sliding conditions. Average surface roughness (Ra), root mean square (Rq), skewness (Rsk) and kurtosis (Rku) were involved in order to analyse the influence of the friction and wear behavior. The observations reveal that a surface with initial roughness parameters of higher Ra, Rq and Rku will lead to a longer initial-steady transition period in the sliding tests. The plastic deformation mainly concentrates in the depth of 20–50 μm under the worn surface and the critical plastic deformation is generated on the rough surface. For surfaces with large Ra, Rq, low Rsk and high Rku values, it is easy to lose the C element in, the reciprocating extrusion. PMID:29401703

  2. An Investigation of the Influence of Initial Roughness on the Friction and Wear Behavior of Ground Surfaces

    Directory of Open Access Journals (Sweden)

    Guoxing Liang

    2018-02-01

    Full Text Available Friction and wear tests were performed on AISI 1045 steel specimens with different initial roughness parameters, machined by a creep-feed dry grinding process, to study the friction and wear behavior on a pin-on-disc tester in dry sliding conditions. Average surface roughness (Ra, root mean square (Rq, skewness (Rsk and kurtosis (Rku were involved in order to analyse the influence of the friction and wear behavior. The observations reveal that a surface with initial roughness parameters of higher Ra, Rq and Rku will lead to a longer initial-steady transition period in the sliding tests. The plastic deformation mainly concentrates in the depth of 20–50 μm under the worn surface and the critical plastic deformation is generated on the rough surface. For surfaces with large Ra, Rq, low Rsk and high Rku values, it is easy to lose the C element in, the reciprocating extrusion.

  3. Wavelet theory and belt finishing process, influence of wavelet shape on the surface roughness parameter values

    International Nuclear Information System (INIS)

    Khawaja, Z; Mazeran, P-E; Bigerelle, M; Guillemot, G; Mansori, M El

    2011-01-01

    This article presents a multi-scale theory based on wavelet decomposition to characterize the evolution of roughness in relation with a finishing process or an observed surface property. To verify this approach in production conditions, analyses were developed for the finishing process of the hardened steel by abrasive belts. These conditions are described by seven parameters considered in the Tagushi experimental design. The main objective of this work is to identify the most relevant roughness parameter and characteristic length allowing to assess the influence of finishing process, and to test the relevance of the measurement scale. Results show that wavelet approach allows finding this scale.

  4. The effect of surface roughness and viscoelasticity on rubber adhesion.

    Science.gov (United States)

    Tiwari, A; Dorogin, L; Bennett, A I; Schulze, K D; Sawyer, W G; Tahir, M; Heinrich, G; Persson, B N J

    2017-05-21

    Adhesion between silica glass or acrylic balls and silicone elastomers and various industrial rubbers is investigated. The work of adhesion during pull-off is found to strongly vary depending on the system, which we attribute to the two opposite effects: (1) viscoelastic energy dissipation close to an opening crack tip and (2) surface roughness. Introducing surface roughness on the glass ball is found to increase the work of adhesion for soft elastomers, while for the stiffer elastomers it results in a strong reduction in the work of adhesion. For the soft silicone elastomers a strong increase in the work of adhesion with increasing pull-off velocity is observed, which may result from the non-adiabatic processes associated with molecular chain pull-out. In general, the work of adhesion is decreased after repeated contacts due to the transfer of molecules from the elastomers to the glass ball. Thus, extracting the free chains (oligomers) from the silicone elastomers is shown to make the work of adhesion independent of the number of contacts. The viscoelastic properties (linear and nonlinear) of all of the rubber compounds are measured, and the velocity dependent crack opening propagation energy at the interface is calculated. Silicone elastomers show a good agreement between the measured work of adhesion and the predicted results, but carbon black filled hydrogenated nitrile butadiene rubber compounds reveal that strain softening at the crack tip may play an important role in determining the work of adhesion. Additionally, adhesion measurement under submerged conditions in distilled water and water + soap solutions are also performed: a strong reduction in the work of adhesion is measured for the silicone elastomers submerged in water, and a complete elimination of adhesion is found for the water + soap solution attributed to an osmotic repulsion between the negatively charged surface of the glass and the elastomer.

  5. Effects of confinement & surface roughness in electrorheological flows

    Science.gov (United States)

    Helal, Ahmed; Telleria, Maria J.; Wang, Julie; Strauss, Marc; Murphy, Mike; McKinley, Gareth; Hosoi, A. E.

    2014-11-01

    Electrorheological (ER) fluids are dielectric suspensions that exhibit a fast, reversible change in rheological properties with the application of an external electric field. Upon the application of the electric field, the material develops a field-dependent yield stress that is typically modeled using a Bingham plastic model. ER fluids are promising for designing small, cheap and rapidly actuated hydraulic devices such as rapidly-switchable valves, where fluid flowing in a microchannel can be arrested by applying an external electric field. In the lubrication limit, for a Bingham plastic fluid, the maximum pressure the channel can hold, before yielding, is a function of the field-dependent yield stress, the length of the channel and the electrode gap. In practice, the finite width of the channel and the surface roughness of the electrodes could affect the maximum yield pressure but a quantitative understanding of these effects is currently lacking. In this study, we experimentally investigate the effects of the channel aspect ratio (width/height) and the effects of electrode roughness on the performance of ER valves. Based on this quantitative analysis, we formulate new performance metrics for ER valves as well as design rules for ER valves that will help guide and optimize future designs.

  6. PREDICTION OF SURFACE ROUGHNESS IN END MILLING OPERATION OF DUPLEX STAINLESS STEEL USING RESPONSE SURFACE METHODOLOGY

    Directory of Open Access Journals (Sweden)

    S. D. PHILIP

    2015-03-01

    Full Text Available Response surface methodology has been used to study the effects of the machining parameters such as spindle speed, feed rate and axial depth of cut on surface roughness of duplex stainless steel in end milling operation. Dry milling experiments were conducted with three levels of spindle speed, feed rate and axial depth of cut. A mathematical model has been developed to predict the surface roughness in terms of the machining parameters using Box-Behnken design response surface methodology. The adequacy of the model was verified using analysis of variance. The prediction equation shows that the feed rate is the most important factor that influences the surface roughness followed by axial depth of cut and spindle speed. The validity of the model was verified by conducting the confirmation experiment.

  7. Contact angles of nanodrops on chemically rough surfaces.

    Science.gov (United States)

    Berim, Gersh O; Ruckenstein, Eli

    2009-08-18

    The experimental observations of Gao and McCarthy [Gao, L.; McCarthy, T. Langmuir, 2007, 23, 3762] that only the interfacial area near the leading edges of the drop on physically smooth but chemically rough solid surfaces affects the contact angle and that most of the contact area has no effect is checked for nanodrops on the basis of a density functional theory. The contact angle was calculated for three cases: (i) the leading edges of the drops are located on much higher or (ii) much lower hydrophobic surfaces than the remaining surface beneath the drop; (iii) the surface is composed of a periodic array of two kinds of stripelike solid plates. In the first two cases, if the distance between the leading edges and the region which has higher or lower hydrophobicity is sufficiently large, there is agreement with the experiments mentioned. However, when those distances are sufficiently small, the internal part affects the value of the angle. In the third case, we found that the internal part always affects the wetting angle. All these peculiarities, as well as the contact angle hysteresis, can be explained by accounting for the local conditions in the vicinity of the leading edges of the drop.

  8. Evaluation of surface roughness of microhybrid and nanofilled composites after pH-cycling and simulated toothbrushing.

    Science.gov (United States)

    Penteado, Roberta Alves Pinto Moura; Tonholo, Josealdo; Júnior, José Ginaldo; Silva, Milton Fernando de Andrade; Queiroz, Celso da Silva; Cavalli, Vanessa; Rego, Marcos Augusto do; Liporoni, Priscila Christiane Suzy

    2010-12-01

    This study evaluated the surface roughness patterns of two resin-based composite restorative materials, a microhybrid (Filtek Z250, 3M ESPE) and a nanofilled (Filtek Supreme, 3M ESPE), subjected to a regimen that simulated dynamic pH-cycling and toothbrushing. Twelve standardized cylindrical specimens of each resin-based composite material were prepared, finished, and mechanically polished. The experimental units were submitted to a pH-cycling regimen followed by 50,000 toothbrushing cycles, after which the surface roughness was measured using an atomic force microscope (AFM). AFM surface roughness was evaluated at three intervals: (1) immediately after specimen preparation (baseline), (2) after pH-cycling, and (3) after simulated toothbrushing. The results were then analyzed using a split-plot design and followed by linear regression and a Tukey's test at a significance level of ptoothbrushing provoked a remarkable increase in surface roughness for both types of composite resins tested (p=0.0031). However, pH-cycling did not alter the surface of the composite under the conditions of this experiment. Based on the results obtained, it was concluded that simulated toothbrushing was capable of increasing the surface roughness of the microhybrid (Filtek Z250) and the nanofilled (Filtek Supreme) composites tested. Surface roughness of nanofilled and microhybrid composites is significantly increased after toothbrushing, although pH-cycling, as tested in this study, does not appear to affect the morphology of either composite material.

  9. Effect of nano- and micro-roughness on adhesion of bioinspired micropatterned surfaces

    NARCIS (Netherlands)

    Canas, N.; Kamperman, M.M.G.; Volker, B.; Kroner, E.; McMeeking, R.M.; Arzt, E.

    2012-01-01

    In this work, the adhesion of biomimetic polydimethylsiloxane (PDMS) pillar arrays with mushroom-shaped tips was studied on nano- and micro-rough surfaces and compared to unpatterned controls. The adhesion strength on nano-rough surfaces invariably decreased with increasing roughness, but pillar

  10. Quality factor due to roughness scattering of shear horizontal surface acoustic waves in nanoresonators

    NARCIS (Netherlands)

    Palasantzas, G.

    2008-01-01

    In this work we study the quality factor associated with dissipation due to scattering of shear horizontal surface acoustic waves by random self-affine roughness. It is shown that the quality factor is strongly influenced by both the surface roughness exponent H and the roughness amplitude w to

  11. Effect of residual stress and surface roughness on the fatigue behaviour of aluminium matrix composites

    International Nuclear Information System (INIS)

    Smaga, M; Eifler, D

    2010-01-01

    In this investigation the fatigue properties of specimens manufactured with different turning parameters were investigated in stress-controlled constant amplitude tests at ambient temperature. The change of feed rate and depth of cut lead to a change in the near surface microstructure. Hence the fatigue properties were influenced significantly due to different surface roughness and surface residual stress resulting from the unequal turning processes. The cyclic deformation behaviour of AMC225xe is characterised by pronounced initial cyclic hardening. Continuous load increase tests allow a reliable estimation of the endurance limit of AMC225xe with one single specimen on the basis of cyclic deformation, temperature and electrical resistance data.

  12. Slippery surfaces of pitcher plants: Nepenthes wax crystals minimize insect attachment via microscopic surface roughness.

    Science.gov (United States)

    Scholz, I; Bückins, M; Dolge, L; Erlinghagen, T; Weth, A; Hischen, F; Mayer, J; Hoffmann, S; Riederer, M; Riedel, M; Baumgartner, W

    2010-04-01

    Pitcher plants of the genus Nepenthes efficiently trap and retain insect prey in highly specialized leaves. Besides a slippery peristome which inhibits adhesion of insects they employ epicuticular wax crystals on the inner walls of the conductive zone of the pitchers to hamper insect attachment by adhesive devices. It has been proposed that the detachment of individual crystals and the resulting contamination of adhesive organs is responsible for capturing insects. However, our results provide evidence in favour of a different mechanism, mainly based on the stability and the roughness of the waxy surface. First, we were unable to detect a large quantity of crystal fragments on the pads of insects detached from mature pitcher surfaces of Nepenthes alata. Second, investigation of the pitcher surface by focused ion beam treatment showed that the wax crystals form a compact 3D structure. Third, atomic force microscopy of the platelet-shaped crystals revealed that the crystals are mechanically stable, rendering crystal detachment by insect pads unlikely. Fourth, the surface profile parameters of the wax layer showed striking similarities to those of polishing paper with low grain size. By measuring friction forces of insects on this artificial surface we demonstrate that microscopic roughness alone is sufficient to minimize insect attachment. A theoretical model shows that surface roughness within a certain length scale will prevent adhesion by being too rough for adhesive pads but not rough enough for claws.

  13. Experimental investigation of surface roughness in electrical discharge turning process

    Science.gov (United States)

    Gohil, Vikas; Puri, Y. M.

    2016-10-01

    In the present study the effects of machining parameters on the average surface roughness (Ra) in electrical discharge turning (EDT) is investigated. EDT is a new machining process in which a rotary spindle is added to a conventional die-sinking EDM machine in order to produce cylindrical components. In this method a new process parameter (spindle rotation) along with pulse on time and current is introduced to study its effect on Ra. This has been done by means of full factorial design (21 × 32) of experiments. A mathematical model has been developed for Ra by regression analysis and factor effects were analyzed using analysis of variance (ANOVA). Signal-to-noise ratio analysis is used to find the optimal condition.

  14. Slope-velocity equilibrium and evolution of surface roughness on a stony hillslope

    Science.gov (United States)

    Nearing, Mark A.; Polyakov, Viktor O.; Nichols, Mary H.; Hernandez, Mariano; Li, Li; Zhao, Ying; Armendariz, Gerardo

    2017-06-01

    Slope-velocity equilibrium is hypothesized as a state that evolves naturally over time due to the interaction between overland flow and surface morphology, wherein steeper areas develop a relative increase in physical and hydraulic roughness such that flow velocity is a unique function of overland flow rate independent of slope gradient. This study tests this hypothesis under controlled conditions. Artificial rainfall was applied to 2 m by 6 m plots at 5, 12, and 20 % slope gradients. A series of simulations were made with two replications for each treatment with measurements of runoff rate, velocity, rock cover, and surface roughness. Velocities measured at the end of each experiment were a unique function of discharge rates, independent of slope gradient or rainfall intensity. Physical surface roughness was greater at steeper slopes. The data clearly showed that there was no unique hydraulic coefficient for a given slope, surface condition, or rainfall rate, with hydraulic roughness greater at steeper slopes and lower intensities. This study supports the hypothesis of slope-velocity equilibrium, implying that use of hydraulic equations, such as Chezy and Manning, in hillslope-scale runoff models is problematic because the coefficients vary with both slope and rainfall intensity.

  15. Analysis of the influence of chemical treatment to the strength and surface roughness of FDM

    Science.gov (United States)

    Hambali, R. H.; Cheong, K. M.; Azizan, N.

    2017-06-01

    The applications of Additive Manufacturing (AM) technology have a greater functionality and wider range of application beyond an intention of prototyping. AM is the process of joining materials to form objects from Computer-Aided Design (CAD) models via layer upon layer process. One of AM technologies is the Fused Deposition Modelling (FDM), which use an extrusion method to create a part. FDM has been applied in many manufacturing applications includes an end-used parts. However, FDM tends to have bad surface quality due to staircase effect and post treatment is required. This chemical treatment is one of a way to improve the surface roughness of FDM fabricated parts. This method is one of economical and faster method. In order to enhance the surface finish of Acrylonitrile-Butadiene-Styrene (ABS) FDM parts by performing chemical treatment in an acetone solution as acetone has very low toxicity, high diffusion and low cost chemical solution. Therefore, the aim of this research is to investigate the influence of chemical treatment to the FDM used part in terms of surface roughness as well as the strength. In this project, ten specimens of standard ASTM D638 dogbone specimens have been fabricated using MOJO 3D printer. Five specimens from the dogbone were tested for surface roughness and tensile testing while another five were immersed in the chemical solution before the same testing. Based on results, the surface roughness of chemically treated dogbone has dramatically improved, compared to untreated dogbone with 97.2% of improvement. However, in term of strength, the tensile strength of dogbone is reduced 42.58% due to the rearrange of material properties and chemical effects to the joining of the filaments. In conclusion, chemical treatment is an economical and sustainable approach to enhance the surface quality of AM parts.

  16. Facet-Mediated Growth of High-Quality Monolayer Graphene on Arbitrarily Rough Copper Surfaces.

    Science.gov (United States)

    Lee, Hyo Chan; Jo, Sae Byeok; Lee, Eunho; Yoo, Min Seok; Kim, Hyun Ho; Lee, Seong Kyu; Lee, Wi Hyoung; Cho, Kilwon

    2016-03-09

    A synthetic approach for high-quality graphene on rough Cu surfaces via chemical vapor deposition is proposed. High-quality graphene is synthesized on rough Cu surfaces by inducing surface faceting of Cu surfaces prior to graphene growth. The electron mobility of synthesized graphene on the rough Cu surfaces is enhanced to 10 335 cm(2) V(-1) s(-1). © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  17. Roughness in Surface Force Measurements: Extension of DLVO Theory To Describe the Forces between Hafnia Surfaces.

    Science.gov (United States)

    Eom, Namsoon; Parsons, Drew F; Craig, Vincent S J

    2017-07-06

    The interaction between colloidal particles is commonly viewed through the lens of DLVO theory, whereby the interaction is described as the sum of the electrostatic and dispersion forces. For similar materials acting across a medium at pH values remote from the isoelectric point the theory typically involves an electrostatic repulsion that is overcome by dispersion forces at very small separations. However, the dominance of the dispersion forces at short separations is generally not seen in force measurements, with the exception of the interaction between mica surfaces. The discrepancy for silica surfaces has been attributed to hydration forces, but this does not explain the situation for titania surfaces where the dispersion forces are very much larger. Here, the interaction forces between very smooth hafnia surfaces have been measured using the colloid probe technique and the forces evaluated within the DLVO framework, including both hydration forces and the influence of roughness. The measured forces across a wide range of pH at different salt concentrations are well described with a single parameter for the surface roughness. These findings show that even small degrees of surface roughness significantly alter the form of the interaction force and therefore indicate that surface roughness needs to be included in the evaluation of surface forces between all surfaces that are not ideally smooth.

  18. Thermal Infrared Spectra of Microcrystalline Sedimentary Phases: Effects of Natural Surface Roughness on Spectral Feature Shape

    Science.gov (United States)

    Hardgrove, C.; Rogers, A. D.

    2012-03-01

    Thermal infrared spectral features of common microcrystalline phases (chert, alabaster, micrite) are presented. Spectra are sensitive to mineralogy and micron-scale (~1-25 µm) surface roughness. Roughness is on the scale of the average crystal size.

  19. Evaluation of hardness and surface roughness of two maxillofacial silicones following disinfection

    Directory of Open Access Journals (Sweden)

    Marcelo Coelho Goiato

    2009-03-01

    Full Text Available The purpose of this study was to evaluate the Shore A hardness and surface roughness of two silicones for maxillofacial prosthetic treatment, under the influence of chemical disinfection and storage. Twenty-eight specimens were obtained, half of which were made of Silastic MDX 4-4210 silicone and, the other half were made of Silastic 732 RTV silicone. The specimens were divided into four groups: Silastic 732 RTV and MDX 4-4210 with disinfection 3 times a week with Efferdent tablets and the same materials without disinfection. The hardness of the materials was analyzed with a Shore A Durometer. The surface roughness was established by a digital portable roughness tester, initially and 2 months after the confection of the specimens. A variance test was applied (2-way ANOVA, followed by Tukey test (the level of significance was set at 1%. The storage time factor statistically influenced (p < 0.01 the materials' properties of hardness and roughness. MDX 4-4210 (28.59 Shore A, 0.789 Ra presented higher values than Silastic 732 RTV (18.08 Shore A, 0.656 Ra for both properties. Regarding the disinfection period, there was no significant difference in any of the materials tested.

  20. A study on the surface roughness of a thin HSQ coating on a fine milled surface

    DEFF Research Database (Denmark)

    Mohaghegh, Kamran; Hansen, Hans Nørgaard; Pranov, Henrik

    2014-01-01

    The paper discusses a novel application of a thin layer coating on a metallic machined surface with particular attention to roughness of the coating compared to the original surface before coating. The coating is a nominally 1 μm film of Hydrogen Silsesquioxane (HSQ) which is commonly used...... in the semiconductor industry in the manufacture of integrated circuits. The work piece is a fine peripheral-milled tool steel surface which is widely used in industrial applications. Roughness improvement after the application of HSQ coating is reported....

  1. The Effects of Heat Treatment on the Physical Properties and Surface Roughness of Turkish Hazel (Corylus colurna L. Wood

    Directory of Open Access Journals (Sweden)

    Nevzat Çakıcıer

    2008-09-01

    Full Text Available Heat treatment is often used to improve the dimensional stability of wood. In this study, the effects of heat treatment on the physical properties and surface roughness of Turkish Hazel (Corylus colurna L. wood were examined. Samples obtained from Kastamonu Forest Enterprises, Turkey, were subjected to heat treatment at varying temperatures and for different durations. The physical properties of heat-treated and control samples were tested, and oven-dry density, air-dry density, and swelling properties were determined. A stylus method was employed to evaluate the surface characteristics of the samples. Roughness measurements, using the stylus method, wereb made in the direction perpendicular to the fiber. Four main roughness parameters, mean arithmetic deviation of profile (Ra, mean peak-to-valley height (Rz, root mean square roughness (Rq, and maximum roughness (Ry obtained from the surface of wood were used to evaluate the effect of heat treatment on the surface characteristics of the specimens. Significant difference was determined (p = 0.05 between physical properties and surface roughness parameters (Ra,Rz, Ry, Rq for three temperatures and three durations of heat treatment. The results showed that the values of density, swelling and surface roughness decreased with increasing temperature treatment and treatment times. Turkish Hazel wood could be utilized successfully by applying proper heat treatment techniques without any losses in investigated parameters. This is vital in areas, such as window frames, where working stability and surface smoothness are important factors.

  2. Hardness and surface roughness of reline and denture base acrylic resins after repeated disinfection procedures.

    Science.gov (United States)

    Machado, Ana Lucia; Breeding, Larry C; Vergani, Carlos Eduardo; da Cruz Perez, Luciano Elias

    2009-08-01

    Microwave irradiation and immersion in chemical solutions have been recommended for denture disinfection. However, the effect of these procedures on the surface characteristics of denture base and reline resins has not been completely evaluated. The purpose of this study was to evaluate the effect of microwave and chemical disinfection on the Vickers hardness (VHN) and surface roughness (Ra, microm) of 2 hard chairside reline resins (Kooliner, DuraLiner II), and 1 heat-polymerizing denture base resin (Lucitone 550). Specimens (12 x 12 x 3 mm) were divided into 2 control and 4 test groups (n=8). Hardness and roughness measurements were performed after: polymerization and immersion in water (37 degrees C) for 7 days (controls), or repeated exposure to disinfection by immersion in sodium perborate (50 degrees C/10 min) or microwave irradiation (650 W/6 min). Measurements of surface roughness (Ra, microm) and hardness (kg/mm(2)) were analyzed using 3-way ANOVA and Tukey's Honestly Significant Difference (HSD) test (alpha=.05). Microwave and chemical disinfection increased the mean (SD) hardness of Kooliner (from 4.1 to 7.5 kg/mm(2)) and DuraLiner II (from 2.6 to 5.6 kg/mm(2)), whereas Lucitone 550 (14.4 kg/mm(2)) remained unaffected. Disinfection by immersion in sodium perborate increased the surface roughness of DuraLiner II (from 0.13 to 0.26 microm) and Kooliner (from 0.16 to 0.26 microm), regardless of the number of cycles. For Lucitone 550, an increase in roughness was observed after 2 cycles of chemical disinfection (from 0.12 to 0.26 microm). Two cycles of microwave disinfection increased the roughness of both reline resins (DuraLiner II: from 0.13 to 0.22 microm; Kooliner: from 0.16 to 0.24 microm), whereas repeated microwave disinfection increased the roughness of DuraLiner II (from 0.11 to 0.25 microm). Disinfection by immersion in sodium perborate or microwave irradiation did not adversely affect the hardness of all materials evaluated. The effect of both

  3. The effect of surface roughness on the transmission of microwave radiation through a planetary surface

    Science.gov (United States)

    Golden, L. M.

    1979-01-01

    To account for surface roughness, the transmission of microwave radiation through a planetary surface to an observer is treated by a Monte Carlo technique. Sizable effects are found near the limb of the planet, and they should be included in analyses of high-resolution observations and high-precision integrated disk observations.

  4. The Global Surface Roughness of 433 Eros from the NEAR-Shoemaker Laser Altimeter (NLR)

    Science.gov (United States)

    Barnouin, O. S.; Susorney, H. C. M.

    2016-12-01

    Surface roughness is the quantitative measure of the change in topography at a given horizontal scale. Previous studies have used surface roughness to map geologic units, choose landing sites, and understand the relative contribution of different geologic processes to topography. The scale that surface roughness is measured at will dictate the geologic processes studied; the majority of studies of the surface roughness of asteroids have focused on centimeter scale roughness (derived from radar measurements). Spacecraft that rendezvous with asteroids and carry laser altimeters such as the Hayabusa 2 and the OSIRIS-REx mission provide topographic data that allows surface roughness to be measured at the scale of meters to hundreds of meters. In this study we focus on understanding how surface roughness is linked to the geologic processes acting on asteroids, with a case study of 433 Eros. To calculate globals maps of the surface roughness on 433 Eros using 3 to 300 m horizontal baselines, we use the Near Earth Asteroid Rendezvous (NEAR)-Shoemaker's laser altimeter (NLR). We measure surface roughness as the Root-Mean Square (RMS) deviation, which is simply the RMS difference in height over a given scale. Because asteroids are typically not spherical, we define surface height to be relative to the asteroid's geoid, similar to how topography is defined on planets. RMS deviation is then used to calculate the Hurst exponent, which quantifies the fractal behavior of the surface and is indicative of the type of geologic processes controlling topography at that scale. The surface roughness on 433 Eros varies regionally, with smaller roughness values where regolith has accumulated, and more elevated roughness values along the walls of large craters or near linear grooves. The roughness seen in crater walls may be evidence for subsurface structures (visible as aligned blocks protruding from the crater walls). The surface roughness of 433 Eros is also remarkably fractal relative

  5. Comparison of Regression and Artificial Neural Network Models for Surface Roughness Prediction with the Cutting Parameters in CNC Turning

    Directory of Open Access Journals (Sweden)

    Muammer Nalbant

    2007-06-01

    Full Text Available Surface roughness, an indicator of surface quality, is one of the most specified customer requirements in machining of parts. In this study, the experimental results corresponding to the effects of different insert nose radii of cutting tools (0.4, 0.8, 1.2 mm, various depth of cuts (0.75, 1.25, 1.75, 2.25, 2.75 mm, and different feedrates (100, 130, 160, 190, 220 mm/min on the surface quality of the AISI 1030 steel workpieces have been investigated using multiple regression analysis and artificial neural networks (ANN. Regression analysis and neural network-based models used for the prediction of surface roughness were compared for various cutting conditions in turning. The data set obtained from the measurements of surface roughness was employed to and tests the neural network model. The trained neural network models were used in predicting surface roughness for cutting conditions. A comparison of neural network models with regression model was carried out. Coefficient of determination was 0.98 in multiple regression model. The scaled conjugate gradient (SCG model with 9 neurons in hidden layer has produced absolute fraction of variance (R2 values of 0.999 for the training data, and 0.998 for the test data. Predictive neural network model showed better predictions than various regression models for surface roughness. However, both methods can be used for the prediction of surface roughness in turning.

  6. Effect of different finishing techniques for restorative materials on surface roughness and bacterial adhesion.

    Science.gov (United States)

    Aykent, Filiz; Yondem, Isa; Ozyesil, Atilla G; Gunal, Solen K; Avunduk, Mustafa C; Ozkan, Semiha

    2010-04-01

    The formation of biofilm and bacterial accumulation on dental materials may lead to the development of gingival inflammation and secondary caries. The purpose of this study was to examine the effect of different surface finishing and polishing methods on surface roughness and the adhesion of S. mutans bacteria to 2 new-generation indirect composite resins, 1 direct composite resin, and 1 ceramic material. Forty specimens (10 x 10 x 2 mm) of each material, indirect composite resins (SR Adoro, Estenia), direct composite resin (Tetric), and a ceramic material (VITABLOCS Mark II), were fabricated. Specimens were divided into 4 groups (n=10) that were treated with 1 of the following 4 surface finishing techniques: diamond rotary cutting instrument, sandpaper discs (Sof-Lex), silicone-carbide rubber points (Shofu), or a felt wheel with diamond paste. Surface roughness was measured with a profilometer. Test specimens were covered with artificial saliva and mucin to produce pellicle. Bacterial suspension (10(9) CFU/ml) was then added to the pellicle-coated specimens, and bacterial adhesion was determined using a confocal laser microscope and image analyzing program. Data were analyzed with 2-way ANOVA, followed by Tukey HSD test, Pearson correlation, and regression analysis (alpha=.05). The highest surface roughness values were recorded in SR Adoro and diamond rotary cutting instrument groups. The lowest vital S. mutans adhesion was seen in the ceramic group and in SR Adoro indirect composite resin (Padhesion to indirect composite resin materials differed from that to ceramic material after surface treatments. A positive correlation was observed between surface roughness and the vital S. mutans adhesion. Copyright 2010 The Editorial Council of the Journal of Prosthetic Dentistry. Published by Mosby, Inc. All rights reserved.

  7. [Surface roughness and gloss of novel flowable composites after polishing and simulated brushing wear].

    Science.gov (United States)

    Wang, R L; Yuan, C Y; Pan, Y X; Tian, F C; Wang, Z H; Wang, X Y

    2017-04-09

    Objective: To investigate surface properties of novel flowable composites after polishing and simulated brushing wear, compared to their pasty counterpart. Methods: Composites employed in this study were: three flowable composites (A1: Clearfil Majesty ES Flow; B1: Beautifil Flow Plus F00; C1: Filtek Bulk Fill) and three paste composites (A2: Clearfil Majesty; B2: Beautifil; C2: Filtek Z350. Eleven disk-shaped specimens were made for each material. The specimens were cured, then subjected to sandpaper finishing for 20 s, one-step polishing for 30 s, finally subjected to simulated brushing for 10 000 cycles. Surface roughness and glossiness were measured before finishing, after finishing, after polishing, after 5 000 brushing cycles and after 10 000 brushing cycles, respectively. Data obtained were analyzed using two-way ANOVA method. Scanning electron microscope was employed to examine the microscopic appearance of each material. Results: Surface roughness (0.11~0.22 μm) and glossiness (74.25~86.48 GU) of each material were similar after one-step polishing. After brushing simulation, roughness increased significantly and glossiness decreased significantly for each material ( Pcomposites of group A1 and B1 tested in the present setup showed better surface properties compared to their pasty counterpart (group A2 and B2). Conclusions: Within the limit of this study, flowable composites tested in the present research can obtain similar surface polish or even better than the paste composite counterpart.

  8. Wear and surface roughness of silorane composites after pH cycling and toothbrushing abrasion.

    Science.gov (United States)

    Ishikiriama, Sérgio Kiyoshi; De Oliveira, Gabriela Ulian; Maenosono, Rafael Massunari; Wang, Linda; Duarte, Marco Antonio Húngaro; Mondelli, Rafael Francisco Lia

    2014-08-01

    To evaluate the effects of toothbrushing abrasion associated with pH cycling on the surface roughness and wear of methacrylate- and silorane-based resin composites. Microhybrid methacrylate-based (Filtek Z250), nanofilled methacrylate-based (Filtek Supreme Ultra) and microhybrid silorane-based (Filtek LS) composites were selected for this investigation. For each composite, two groups (n = 10) of rectangular specimens were made. The initial roughness (Ra) of all of the groups was evaluated based on the average of three random tracings with a profilometer, and each specimen had half of its surface protected with two layers of nail varnish to serve as controls. Half of the specimens of each resin were submitted to pH cycling, while the other half were stored in deionized water for 14 days. Subsequently, 100,000 strokes of simulated toothbrushing were performed. Final roughness and wear were measured with the same profilometer, and the values were submitted to ANOVA, Student's t-test and Tukey's test (P toothbrushing, while Filtek LS showed the opposite behavior. Methacrylate-based composites presented lower wear values [Z250 (4.19 ± 1.73 μm); Supreme Ultra (4.16 ± 0.95 μm)], while the silorane-based composite presented increased surface roughness (11.51 ± 5.69 μm), particularly when submitted to pH cycling (15.31 ± 5.41 μm). Despite the good properties of silorane-based composites, particularly its smooth surface roughness even after pH cycling and toothbrushing abrasion, this composite still presented increased wear, which is an important issue for the development of new resin compositions.

  9. Evaluation of surface roughness and bond strength of quartz fiber posts after various pre-treatments.

    Science.gov (United States)

    Akin, Gulsah E; Akin, Hakan; Sipahi, Cumhur; Piskin, Bulent; Kirmali, Omer

    2014-11-01

    Debonding at the post-adhesive interface is a major problem for quartz fiber posts. The objective of this study was to evaluate surface roughness and bond strength of quartz fiber posts after various surface treatments. Sixty-six quartz fiber posts were randomly divided into six experimental groups (n = 11) including group C, untreated (control); group SB, sandblasted; group SC, silica coated; group HF, hydrofluoric acid-etched; group N, Nd:YAG laser irradiated; group E, Er:YAG laser irradiated. Surface roughness of the posts was measured before and after pre-treatment. They were then bonded to resin cement and tensile bond strength was determined in a universal testing machine. Furthermore, two-way ANOVA and post hoc comparison tests (α = 0.05) were performed on all data. The highest mean force value was observed in group SB and followed by group E. Tukey's HSD test showed that there was no statistical difference between group SB and group E (p = 0.673). The highest mean roughness value was observed in group SB and a significant difference was found between group SB and all other groups (p quartz fiber posts and resin cement. Sandblasting or Er:YAG laser-irradiation of the surface of the quartz fiber post before cementation is recommended for increasing retention.

  10. Does surface roughness influence the primary stability of acetabular cups? A numerical and experimental biomechanical evaluation.

    Science.gov (United States)

    Le Cann, Sophie; Galland, Alexandre; Rosa, Benoît; Le Corroller, Thomas; Pithioux, Martine; Argenson, Jean-Noël; Chabrand, Patrick; Parratte, Sébastien

    2014-09-01

    Most acetabular cups implanted today are press-fit impacted cementless. Anchorage begins with the primary stability given by insertion of a slightly oversized cup. This primary stability is key to obtaining bone ingrowth and secondary stability. We tested the hypothesis that primary stability of the cup is related to surface roughness of the implant, using both an experimental and a numerical models to analyze how three levels of surface roughness (micro, macro and combined) affect the primary stability of the cup. We also investigated the effect of differences in diameter between the cup and its substrate, and of insertion force, on the cups' primary stability. The results of our study show that primary stability depends on the surface roughness of the cup. The presence of macro-roughness on the peripheral ring is found to decrease primary stability; there was excessive abrasion of the substrate, damaging it and leading to poor primary stability. Numerical modeling indicates that oversizing the cup compared to its substrate has an impact on primary stability, as has insertion force. Copyright © 2014 IPEM. Published by Elsevier Ltd. All rights reserved.

  11. Stick-slip friction of gecko-mimetic flaps on smooth and rough surfaces.

    Science.gov (United States)

    Das, Saurabh; Cadirov, Nicholas; Chary, Sathya; Kaufman, Yair; Hogan, Jack; Turner, Kimberly L; Israelachvili, Jacob N

    2015-03-06

    The discovery and understanding of gecko 'frictional-adhesion' adhering and climbing mechanism has allowed researchers to mimic and create gecko-inspired adhesives. A few experimental and theoretical approaches have been taken to understand the effect of surface roughness on synthetic adhesive performance, and the implications of stick-slip friction during shearing. This work extends previous studies by using a modified surface forces apparatus to quantitatively measure and model frictional forces between arrays of polydimethylsiloxane gecko footpad-mimetic tilted microflaps against smooth and rough glass surfaces. Constant attachments and detachments occur between the surfaces during shearing, as described by an avalanche model. These detachments ultimately result in failure of the adhesion interface and have been characterized in this study. Stick-slip friction disappears with increasing velocity when the flaps are sheared against a smooth silica surface; however, stick-slip was always present at all velocities and loads tested when shearing the flaps against rough glass surfaces. These results demonstrate the significance of pre-load, shearing velocity, shearing distances, commensurability and shearing direction of gecko-mimetic adhesives and provide us a simple model for analysing and/or designing such systems. © 2015 The Author(s) Published by the Royal Society. All rights reserved.

  12. Stick–slip friction of gecko-mimetic flaps on smooth and rough surfaces

    Science.gov (United States)

    Das, Saurabh; Cadirov, Nicholas; Chary, Sathya; Kaufman, Yair; Hogan, Jack; Turner, Kimberly L.; Israelachvili, Jacob N.

    2015-01-01

    The discovery and understanding of gecko ‘frictional-adhesion’ adhering and climbing mechanism has allowed researchers to mimic and create gecko-inspired adhesives. A few experimental and theoretical approaches have been taken to understand the effect of surface roughness on synthetic adhesive performance, and the implications of stick–slip friction during shearing. This work extends previous studies by using a modified surface forces apparatus to quantitatively measure and model frictional forces between arrays of polydimethylsiloxane gecko footpad-mimetic tilted microflaps against smooth and rough glass surfaces. Constant attachments and detachments occur between the surfaces during shearing, as described by an avalanche model. These detachments ultimately result in failure of the adhesion interface and have been characterized in this study. Stick–slip friction disappears with increasing velocity when the flaps are sheared against a smooth silica surface; however, stick–slip was always present at all velocities and loads tested when shearing the flaps against rough glass surfaces. These results demonstrate the significance of pre-load, shearing velocity, shearing distances, commensurability and shearing direction of gecko-mimetic adhesives and provide us a simple model for analysing and/or designing such systems. PMID:25589569

  13. Milled Die Steel Surface Roughness Correlation with Steel Sheet Friction

    DEFF Research Database (Denmark)

    Berglund, J.; Brown, C.A.; Rosén, B.-G.

    2010-01-01

    This work investigates correlations between the surface topography ofmilled steel dies and friction with steel sheet. Several die surfaces were prepared by milling. Friction was measured in bending under tension testing. Linear regression coefficients (R2) between the friction and texture...

  14. Modeling of surface roughness effects on Stokes flow in circular pipes

    Science.gov (United States)

    Song, Siyuan; Yang, Xiaohu; Xin, Fengxian; Lu, Tian Jian

    2018-02-01

    Fluid flow and pressure drop across a channel are significantly influenced by surface roughness on a channel wall. The present study investigates the effects of periodically structured surface roughness upon flow field and pressure drop in a circular pipe at low Reynolds numbers. The periodic roughness considered exhibits sinusoidal, triangular, and rectangular morphologies, with the relative roughness (i.e., ratio of the amplitude of surface roughness to hydraulic diameter of the pipe) no more than 0.2. Based upon a revised perturbation theory, a theoretical model is developed to quantify the effect of roughness on fully developed Stokes flow in the pipe. The ratio of static flow resistivity and the ratio of the Darcy friction factor between rough and smooth pipes are expressed in four-order approximate formulations, which are validated against numerical simulation results. The relative roughness and the wave number are identified as the two key parameters affecting the static flow resistivity and the Darcy friction factor.

  15. Separate effects of surface roughness, wettability and porosity on the Leidenfrost temperature of water

    Energy Technology Data Exchange (ETDEWEB)

    Kim, H., E-mail: hdkims@khu.ac.kr [Massachusetts Inst. of Tech., Nuclear Science and Engineering Dept., Cambridge, Massachusetts (United States); Kyung Hee University, Nuclear Engineering Dept., Yongin (Korea, Republic of); Truong, B.; Buongiorno, J., E-mail: baot@mit.edu, E-mail: jacopo@mit.edu [Massachusetts Inst. of Tech., Nuclear Science and Engineering Dept., Cambridge, Massachusetts (United States); Hu, L.-W., E-mail: lwhu@mit.edu [Massachusetts Int. of Tech., Nuclear Reactor Laboratory, Cambridge, Massachusetts (United States)

    2011-07-01

    Quenching phenomena play a key role in LWR safety, particularly in the reflood phase of a large-break LOCA. It is well known that quenching phenomena are affected by the physico-chemical characteristics of the hot surface, such as surface roughness, wettability and porosity. However, while some general qualitative trends are known, there is a lack of quantitative data on the relative importance and magnitude of these effects. Therefore, we have conducted water-droplet Leidenfrost Point (LFP) tests using custom-fabricated surfaces for which roughness, wettability and porosity were controlled accurately and separately at the nanoscale. This approach reveals that nanoporosity is the crucial feature in efficiently increasing the LFP temperature by initiating heterogeneous nucleation of bubbles during short-lived solid-liquid contacts, which results in disruption of the vapor film. (author)

  16. Symmetric and asymmetric capillary bridges between a rough surface and a parallel surface.

    Science.gov (United States)

    Wang, Yongxin; Michielsen, Stephen; Lee, Hoon Joo

    2013-09-03

    Although the formation of a capillary bridge between two parallel surfaces has been extensively studied, the majority of research has described only symmetric capillary bridges between two smooth surfaces. In this work, an instrument was built to form a capillary bridge by squeezing a liquid drop on one surface with another surface. An analytical solution that describes the shape of symmetric capillary bridges joining two smooth surfaces has been extended to bridges that are asymmetric about the midplane and to rough surfaces. The solution, given by elliptical integrals of the first and second kind, is consistent with a constant Laplace pressure over the entire surface and has been verified for water, Kaydol, and dodecane drops forming symmetric and asymmetric bridges between parallel smooth surfaces. This solution has been applied to asymmetric capillary bridges between a smooth surface and a rough fabric surface as well as symmetric bridges between two rough surfaces. These solutions have been experimentally verified, and good agreement has been found between predicted and experimental profiles for small drops where the effect of gravity is negligible. Finally, a protocol for determining the profile from the volume and height of the capillary bridge has been developed and experimentally verified.

  17. Quantitative roughness characterization of geological surfaces and implications for radar signature analysis

    DEFF Research Database (Denmark)

    Dierking, Wolfgang

    1999-01-01

    Stochastic surface models are useful for analyzing in situ roughness profiles and synthetic aperture radar (SAR) images of geological terrain. In this paper, two different surface models are discussed: surfaces with a stationary random roughness (conventional model) and surfaces with a power...

  18. Stochastic Radiative Transfer Model for Contaminated Rough Surfaces: A Framework for Detection System Design

    Science.gov (United States)

    2013-11-01

    Contaminated surfaces Detection Rough surface BRDF Reflectance Fill factor CFAR Data fusion (Continued on next page.) 16...surfaces, detection, rough surface, BRDF, reflectance, fill factor, distributed binary integration, CFAR , data fusion, distributed sensor system, double...detection, tem)detect(sys)( 1 PP systemmiss  , for a given constraint of constant false alarm ( CFAR ) system-false-alarm probability, )( systemfalseP

  19. Evaluation of Surface Roughness and Tensile Strength of Base Metal Alloys Used for Crown and Bridge on Recasting (Recycling).

    Science.gov (United States)

    Agrawal, Amit; Hashmi, Syed W; Rao, Yogesh; Garg, Akanksha

    2015-07-01

    Dental casting alloys play a prominent role in the restoration of the partial dentition. Casting alloys have to survive long term in the mouth and also have the combination of structure, molecules, wear resistance and biologic compatibility. According to ADA system casting alloys were divided into three groups (wt%); high noble, Noble and predominantly base metal alloys. To evaluate the mechanical properties such as tensile strength and surface roughness of the new and recast base metal (nickel-chromium) alloys. Recasting of the base metal alloys derived from sprue and button, to make it reusable has been done. A total of 200 test specimens were fabricated using specially fabricated jig of metal and divided into two groups- 100 specimens of new alloy and 100 specimens of recast alloys, which were tested for tensile strength on universal testing machine and surface roughness on surface roughness tester. Tensile strength of new alloy showed no statistically significant difference (p-value>0.05) from recast alloy whereas new alloy had statistically significant surface roughness (Maximum and Average surface roughness) difference (p-valuetensile strength will not be affected by recasting of nickel-chromium alloy whereas surface roughness increases markedly.

  20. Weight loss and changes in surface roughness of denture base and reline materials after simulated toothbrushing in vitro.

    Science.gov (United States)

    Machado, Ana Lucia; Giampaolo, Eunice Teresinha; Vergani, Carlos Eduardo; Pavarina, Ana Cláudia; Salles, Débora da Silva Lopes; Jorge, Janaina Habib

    2012-06-01

    To evaluate the weight loss and the surface roughness of acrylic resins after simulated brushing tests. Ten specimens of each material (Tokuyama Rebase II-TR, New Truliner-NT, Ufi Gel Hard-UH and Lucitone 550-L) were made. The wear loss (mg) by weight and the surface roughness (Ra μm) of each specimen was determined before and after brushing. The specimens were placed on the brushing machine and a total of 20,000 brushing cycles was performed. The results of weight loss and roughness values were submitted to the anova followed by the Tukey's test (p = 0.05). The mean weight loss of material L was statistically higher (p 0.05). Only for L, toothbrushing increased the surface roughness. After toothbrushing, there was no significant difference between the roughness values of materials L and NT. The highest mean weight loss during the simulated toothbrushing tests was observed for L. Before the toothbrushing tests, the NT exhibited the highest mean roughness. Brushing resulted in increase in roughness only for resin L. © 2011 The Gerodontology Society and John Wiley & Sons A/S.

  1. Spatially-varying surface roughness and ground-level air quality in an operational dispersion model

    International Nuclear Information System (INIS)

    Barnes, M.J.; Brade, T.K.; MacKenzie, A.R.; Whyatt, J.D.; Carruthers, D.J.; Stocker, J.; Cai, X.; Hewitt, C.N.

    2014-01-01

    Urban form controls the overall aerodynamic roughness of a city, and hence plays a significant role in how air flow interacts with the urban landscape. This paper reports improved model performance resulting from the introduction of variable surface roughness in the operational air-quality model ADMS-Urban (v3.1). We then assess to what extent pollutant concentrations can be reduced solely through local reductions in roughness. The model results suggest that reducing surface roughness in a city centre can increase ground-level pollutant concentrations, both locally in the area of reduced roughness and downwind of that area. The unexpected simulation of increased ground-level pollutant concentrations implies that this type of modelling should be used with caution for urban planning and design studies looking at ventilation of pollution. We expect the results from this study to be relevant for all atmospheric dispersion models with urban-surface parameterisations based on roughness. -- Highlights: • Spatially variable roughness improved performance of an operational model. • Scenario modelling explored effect of reduced roughness on air pollution. • Reducing surface roughness can increase modelled ground-level pollution. • Damped vertical mixing outweighs increased horizontal advection in model study. • Result should hold for any model with a land-surface coupling based on roughness. -- Spatially varying roughness improves model simulations of urban air pollutant dispersion. Reducing roughness does not always decrease ground-level pollution concentrations

  2. Efficacy of polishing kits on the surface roughness and color stability of different composite resins.

    Science.gov (United States)

    Kocaagaoglu, H; Aslan, T; Gürbulak, A; Albayrak, H; Taşdemir, Z; Gumus, H

    2017-05-01

    Different polishing kits may have different effects on the composite resin surfaces. The aim of this study was to evaluate the surface roughness and color stability of four different composites which was applied different polishing technique. Thirty specimens were made for each composite resin group (nanohybrid, GrandioSo-GS; nanohybrid, Clearfil Majesty Esthetic-CME; hybrid, Valux Plus-VP; micro-hybrid, Ruby Comp-RC; [15 mm in diameter and 2 mm height]), with the different monomer composition and particle size from a total of 120 specimens. Each composite group was divided into three subgroups (n = 10). The first subgroup of the each composite subgroups served as control (C) and had no surface treatment. The second subgroup of the each composite resin groups was polished with finishing discs (Bisco Finishing Discs; Bisco Inc., Schaumburg, IL, USA). The third subgroup of the each composite resin was polished with polishing wheel (Enhance and PoGo, Dentsply, Konstanz, Germany). The surface roughness and the color differences measurement of the specimens were made and recorded. The data were compared using Kruskal-Wallis test, and regression analysis was used in order to examine the correlation between surface roughness and color differences of the specimens (α = 0.05). The Kruskal-Wallis test indicated significant difference among the composite resins in terms of ΔE (P composite resins in terms of surface roughness (P > 0.05). Result of the regression analysis indicated statistically significant correlation between Ra and ΔE values (P < 0.05, r2 = 0.74). The findings of the present study have clinical relevance in the choice of polishing kits used.

  3. Fluoride release and surface roughness of a new glass ionomer cement: glass carbomer

    Directory of Open Access Journals (Sweden)

    Célia Maria Condeixa de França LOPES

    2018-02-01

    Full Text Available Abstract Objective This study analyzed the fluoride release/recharge and surface roughness of glass carbomer compared to other encapsulated glass ionomer cements (GICs. Material and method The GICs tested were Glass Fill® (GC-GCP Dental, Riva Self Cure® (RS-SDI, Riva Light Cure® (RL-SDI, Equia Fil® (EF-GC Europe. The composite resin Luna® (LU-SDI was used as control. Five samples of each material were prepared and kept in a humidifier for 24 hours (37 °C, 100% relative humidity. Fluoride release was measured in two times: before (T1: days 1, 2, 7, 14 and after topical application of fluoride (T2: days 15, 16, 21 and 28. The surface roughness was also measured in both times (T1: days 1 and 14; T2: days 15 and 28. All samples were submitted to a single topical application of acidulated fluoride phosphate (Fluor Care - FGM. Two-way ANOVA with repeated measures and Tukey's post-test (p <0.05 were used in the statistical analysis. Result Equia Fil presented the highest fluoride release in both evaluation periods, with a higher release in T1 (p <0.05. The other materials tested, including glass carbomer presented similar release in both periods (T1 and T2. Regarding surface roughness, no significant differences were observed in the interaction between the material × time factors (T1 and T2 (p=0.966. Conclusion The GICs tested presented fluoride release and recharge ability and showed no surface roughness increase by topical application of fluoride.

  4. Experimental Research and Mathematical Modeling of Parameters Effecting on Cutting Force and SurfaceRoughness in CNC Turning Process

    Science.gov (United States)

    Zeqiri, F.; Alkan, M.; Kaya, B.; Toros, S.

    2018-01-01

    In this paper, the effects of cutting parameters on cutting forces and surface roughness based on Taguchi experimental design method are determined. Taguchi L9 orthogonal array is used to investigate the effects of machining parameters. Optimal cutting conditions are determined using the signal/noise (S/N) ratio which is calculated by average surface roughness and cutting force. Using results of analysis, effects of parameters on both average surface roughness and cutting forces are calculated on Minitab 17 using ANOVA method. The material that was investigated is Inconel 625 steel for two cases with heat treatment and without heat treatment. The predicted and calculated values with measurement are very close to each other. Confirmation test of results showed that the Taguchi method was very successful in the optimization of machining parameters for maximum surface roughness and cutting forces in the CNC turning process.

  5. AFM Surface Roughness and Topography Analysis of Lithium Disilicate Glass Ceramic

    Directory of Open Access Journals (Sweden)

    M. Pantić

    2015-12-01

    Full Text Available The aim of this study is presenting AFM analysis of surface roughness of Lithium disilicate glass ceramic (IPS e.max CAD under different finishing procedure (techniques: polishing, glazing and grinding. Lithium disilicate glass ceramics is all-ceramic dental system which is characterized by high aesthetic quality and it can be freely said that properties of material provide all prosthetic requirements: function, biocompatibility and aesthetic. Experimental tests of surface roughness were investigated on 4 samples with dimensions: 18 mm length, 14 mm width and 12 mm height. Contact surfaces of three samples were treated with different finishing procedure (polishing, glazing and grinding, and the contact surface of the raw material is investigated as a fourth sample. Experimental measurements were done using the Atomic Force Microscopy (AFM of NT-MDT manufacturers, in the contact mode. All obtained results of different prepared samples are presented in the form of specific roughness parameters (Rа, Rz, Rmax, Rq and 3D surface topography.

  6. Characterizing the effects of regolith surface roughness on photoemission from surfaces in space

    Science.gov (United States)

    Dove, A.; Horanyi, M.; Wang, X.

    2017-12-01

    Surfaces of airless bodies and spacecraft in space are exposed to a variety of charging environments. A balance of currents due to plasma bombardment, photoemission, electron and ion emission and collection, and secondary electron emission determines the surface's charge. Photoelectron emission is the dominant charging process on sunlit surfaces in the inner solar system due to the intense solar UV radiation. This can result in a net positive surface potential, with a cloud of photoelectrons immediately above the surface, called the photoelectron sheath. Conversely, the unlit side of the body will charge negatively due the collection of the fast-moving solar wind electrons. The interaction of charged dust grains with these positively and negatively charged surfaces, and within the photoelectron and plasma sheaths may explain the occurrence of dust lofting, levitation and transport above the lunar surface. The surface potential of exposed objects is also dependent on the material properties of their surfaces. Composition and particle size primarily affect the quantum efficiency of photoelectron generation; however, surface roughness can also control the charging process. In order to characterize these effects, we have conducted laboratory experiments to examine the role of surface roughness in generating photoelectrons in dedicated laboratory experiments using solid and dusty surfaces of the same composition (CeO2), and initial comparisons with JSC-1 lunar simulant. Using Langmuir probe measurements, we explore the measured potentials above insulating surfaces exposed to UV and an electric field, and we show that the photoemission current from a dusty surface is largely reduced due to its higher surface roughness, which causes a significant fraction of the emitted photoelectrons to be re-absorbed within the surface. We will discuss these results in context of similar situations on planetary surfaces.

  7. Influence of roughness of machined surface on adhesion of anticorrosion system

    Directory of Open Access Journals (Sweden)

    Jiří Votava

    2013-01-01

    Full Text Available The goal of this experiment is to analyse dependence of roughness of machined surface on adhesion performance of various anticorrosion systems. In order to prepare samples for the experiment, samples were milled on a knee and column type of a horizontal milling machine. Depending on cutting conditions and machining tool, there were set intervals of roughness of machined surface which are commonly achievable on this type of machine. It is a roughness in the interval of 0.4–1.6 µm (finishing, 1.6–6.3 µm (standard milling a 6.3–12.5 µm (roughening. Removable cutting tips were used as a machining tool and for roughening, a shell end milling cutter NAREX 63x40 HSS 90 was used. Three types of anticorrosion systems were used in order to analyse the adhesion, that is a water-thinnable system Eternal, synthetic single layer coating Hostagrund and a duplex system, whose first layer is formed by dipped zinc and a top layer by a single-layer acrylate system Zinorex. Testing of the influence of surface roughness (anchoring system on adhesion of the individual anticorrosion systems were processed in compliance with the norm ČSN EN ISO 4624, a tearing test. The main criterion of adhesion of anticorrosion system is defined as a power which needed for tear-off testing object stuck to a tested sample. This analysis was processed also during the corrosion test in the salt spray environment according to the norm ČSN EN ISO 9227. In order to better identify the adhesion of the individual anticorrosion systems, the analysis of undercorrosion according to the norm ISO 4628-8 was processed.

  8. Critical surface roughness for wall bounded flow of viscous fluids in an electric submersible pump

    Science.gov (United States)

    Deshmukh, Dhairyasheel; Siddique, Md Hamid; Kenyery, Frank; Samad, Abdus

    2017-11-01

    Surface roughness plays a vital role in the performance of an electric submersible pump (ESP). A 3-D numerical analysis has been carried out to find the roughness effect on ESP. The performance of pump for steady wall bounded turbulent flows is evaluated at different roughness values and compared with smooth surface considering a non-dimensional roughness factor K. The k- ω SST turbulence model with fine mesh at near wall region captures the rough wall effects accurately. Computational results are validated with experimental results of water (1 cP), at a design speed (3000 RPM). Maximum head is observed for a hydraulically smooth surface (K=0). When roughness factor is increased, the head decreases till critical roughness factor (K=0.1) due to frictional loss. Further increase in roughness factor (K>0.1) increases the head due to near wall turbulence. The performance of ESP is analyzed for turbulent kinetic energy and eddy viscosity at different roughness values. The wall disturbance over the rough surface affects the pressure distribution and velocity field. The roughness effect is predominant for high viscosity oil (43cP) as compared to water. Moreover, the study at off-design conditions showed that Reynolds number influences the overall roughness effect.

  9. Self-affine roughness influence on the friction coefficient for rubbers onto solid surfaces

    NARCIS (Netherlands)

    Palasantzas, G

    2004-01-01

    In this paper we investigate the influence of self-affine roughness on the friction coefficient mu(f) of a rubber body under incomplete contact onto a solid surface. The roughness is characterized by the rms amplitude w, the correlation length xi, and the roughness exponent H. It is shown that with

  10. Functional levels of floor surface roughness for the prevention of slips and falls: clean-and-dry and soapsuds-covered wet surfaces.

    Science.gov (United States)

    Kim, In-Ju; Hsiao, Hongwei; Simeonov, Peter

    2013-01-01

    Literature has shown a general trend that slip resistance performance improves with floor surface roughness. However, whether slip resistance properties are linearly correlated with surface topographies of the floors or what roughness levels are required for effective slip resistance performance still remain to be answered. This pilot study aimed to investigate slip resistance properties and identify functional levels of floor surface roughness for practical design applications in reducing the risk of slip and fall incidents. A theory model was proposed to characterize functional levels of surface roughness of floor surfaces by introducing a new concept of three distinctive zones. A series of dynamic friction tests were conducted using 3 shoes and 9 floor specimens under clean-and-dry as well as soapsuds-covered slippery wet environments. The results showed that all the tested floor-shoe combinations provided sufficient slip resistances performance under the clean-and-dry condition. A significant effect of floor type (surface roughness) on dynamic friction coefficient (DFC) was found in the soapsuds-covered wet condition. As compared to the surface roughness effects, the shoe-type effects were relatively small. Under the soapsuds-covered wet condition, floors with 50 μm in Ra roughness scale seemed to represent an upper bound in the functional range of floor surface roughness for slip resistance because further increase of surface roughness provided no additional benefit. A lower bound of the functional range for slip resistance under the soapsuds-covered wet condition was estimated from the requirement of DFC > 0.4 at Ra ≅ 17 μm. Findings from this study may have potential safety implications in the floor surface design for reducing slip and fall hazards. Published by Elsevier Ltd.

  11. Deposition of latex colloids at rough mineral surfaces: an analogue study using nanopatterned surfaces.

    Science.gov (United States)

    Krishna Darbha, Gopala; Fischer, Cornelius; Michler, Alex; Luetzenkirchen, Johannes; Schäfer, Thorsten; Heberling, Frank; Schild, Dieter

    2012-04-24

    Deposition of latex colloids on a structured silicon surface was investigated. The surface with well-defined roughness and topography pattern served as an analogue for rough mineral surfaces with half-pores in the submicrometer size. The silicon topography consists of a regular pit pattern (pit diameter = 400 nm, pit spacing = 400 nm, pit depth = 100 nm). Effects of hydrodynamics and colloidal interactions in transport and deposition dynamics of a colloidal suspension were investigated in a parallel plate flow chamber. The experiments were conducted at pH ∼ 5.5 under both favorable and unfavorable adsorption conditions using carboxylate functionalized colloids to study the impact of surface topography on particle retention. Vertical scanning interferometry (VSI) was applied for both surface topography characterization and the quantification of colloidal retention over large fields of view. The influence of particle diameter variation (d = 0.3-2 μm) on retention of monodisperse as well as polydisperse suspensions was studied as a function of flow velocity. Despite electrostatically unfavorable conditions, at all flow velocities, an increased retention of colloids was observed at the rough surface compared to a smooth surface without surface pattern. The impact of surface roughness on retention was found to be more significant for smaller colloids (d = 0.3, 0.43 vs. 1, 2 μm). From smooth to rough surfaces, the deposition rate of 0.3 and 0.43 μm colloids increased by a factor of ∼2.7 compared to a factor of 1.2 or 1.8 for 1 and 2 μm colloids, respectively. For a substrate herein, with constant surface topography, the ratio between substrate roughness and radius of colloid, Rq/rc, determined the deposition efficiency. As Rq/rc increased, particle-substrate overall DLVO interaction energy decreased. Larger colloids (1 and 2 μm) beyond a critical velocity (7 × 10(-5) and 3 × 10(-6) m/s) (when drag force exceeds adhesion force) tend to detach from the surface

  12. Ice particle habit and surface roughness derived from PARASOL polarization measurements

    OpenAIRE

    B. H. Cole; P. Yang; B. A. Baum; J. Riedi; L. C.-Labonnote

    2014-01-01

    Ice clouds are an important element in the radiative balance of the earth's climate system, but their microphysical and optical properties still are not well constrained, especially ice particle habit and the degree of particle surface roughness. In situ observations have revealed common ice particle habits and evidence for surface roughness, but these observations are limited. An alternative is to infer the ice particle shape and surface roughness from satellite observat...

  13. Influence of Sea Surface Roughness on the Electromagnetic Wave Propagation in the Duct Environment

    OpenAIRE

    Zhao, X.; Huang, S.

    2010-01-01

    This paper deals with a study of the influence of sea surface roughness on the electromagnetic wave propagation in the duct environment. The problem of electromagnetic wave propagation is modeled by using the parabolic equation method. The roughness of the sea surface is computed by modifying the smooth surface Fresnel reflection coefficient to account for the reduction in the specular reflection due to the roughness resulting from sea wind speed. The propagation model is solved by the mixed ...

  14. Tailoring Surface Roughness by Grafting Nanoparticles to Random Copolymer Films

    Science.gov (United States)

    Caporizzo, Matthew; Ezzibdeh, Rami; Composto, Russell

    2013-03-01

    The effect of random copolymer composition on surface attachment and sinking of amine functionalized silica nanoparticles (d =45 nm) is investigated. Films of poly(styrene-ran-tert-butyl acrylate) (StBA) with 37% tBA are converted to poly(S-ran-acrylic acid) (SAA) by annealing for 15h at temperatures ranging from 135C to 200C. The conversion of the tBA ranges from under 10% to 100% and is monitored by ellipsometry and ATR-FTIR. At complete conversion (25 wt% AA), SAA forms nano-phase separated domains that result in particle aggregation within AA rich domains. At lower AA conversion, a disordered polymer morphology leads to grafting sites which are randomly distributed. NPs graft from nearly a complete monolayer to multilayers depending the percent of AA. Both the rate of NP attachment and the maximum loading of NPs into the film scale with the fraction of AA; this behavior is attributed to a reduction in the energetic barrier for the particle to sink into the film with increased swelling (more hydrophilic). A particularly attractive outcome of this systematic study is that optically transparent films with controlled roughness can be routinely prepared. Such films are of interest for investigating biomolecular adsorption and superhydrophobic, clear, non-fouling coatings. Supported by NSF DMR08-32802.

  15. Roughness, surface energy, and superficial damages of CAD/CAM materials after surface treatment.

    Science.gov (United States)

    Strasser, Thomas; Preis, Verena; Behr, Michael; Rosentritt, Martin

    2018-02-05

    The aim of this study was to examine the effects of surface pre-treatment on CAD/CAM materials including ceramics, zirconia, resin-infiltrated ceramic, and resin-based composite. Specimens were made of ten CAD/CAM materials (Celtra Duo, Degudent, D; Vita Suprinity, Vita, D; E.max CAD, Ivoclar-Vivadent, FL; E.max ZirCAD, Ivoclar-Vivadent, FL; Vita Enamic, Vita, D; Cerasmart, GC, B; LAVA Ultimate, 3M, D; SHOFU Block HC, SHOFU, US; Grandio Blocs, VOCO, D; BRILLIANT Crios, Coltene, CH) and pretreated to represent clinical procedures (Hf 20 s/5%; phosphoric acid 20 s/37%; Monobond etch and prime (Ivoclar-Vivadent, FL); water-cooled diamond bur (80 μm; 4 μm); Al 2 O 3 -blasting (50 μm/1 bar, 50 μm/2 bar, 120 μm/1 bar, 120 μm/2 bar); untreated; manufacturer's instructions). SEM-analysis (Phenom, FEI, NL) of the surfaces was performed (magnifications ≤ 10,000×). Roughness values R a , R z (KJ 3D, Keyence, J), and surface energy SE (OCA15 plus, SCA20, DataPhysics, D) were determined (statistics: non-parametric Mann-Whitney U test/Kruskal-Wallis test for independent specimen, α = 0.05). Kruskal-Wallis revealed significant (p CAD/CAM materials require individual pre-treatment for optimized and protective surface activation. Cementation is a key factor for clinical success. Given the variety of available CAD/CAM materials, specific procedures are needed.

  16. Using Wavelet Packet Transform for Surface Roughness Evaluation and Texture Extraction.

    Science.gov (United States)

    Wang, Xiao; Shi, Tielin; Liao, Guanglan; Zhang, Yichun; Hong, Yuan; Chen, Kepeng

    2017-04-23

    Surface characterization plays a significant role in evaluating surface functional performance. In this paper, we introduce wavelet packet transform for surface roughness characterization and surface texture extraction. Surface topography is acquired by a confocal laser scanning microscope. Smooth border padding and de-noise process are implemented to generate a roughness surface precisely. By analyzing the high frequency components of a simulated profile, surface textures are separated by using wavelet packet transform, and the reconstructed roughness and waviness coincide well with the original ones. Wavelet packet transform is then used as a smooth filter for texture extraction. A roughness specimen and three real engineering surfaces are also analyzed in detail. Profile and areal roughness parameters are calculated to quantify the characterization results and compared with those measured by a profile meter. Most obtained roughness parameters agree well with the measurement results, and the largest deviation occurs in the skewness. The relations between the roughness parameters and noise are analyzed by simulation for explaining the relatively large deviations. The extracted textures reflect the surface structure and indicate the manufacturing conditions well, which is helpful for further feature recognition and matching. By using wavelet packet transform, engineering surfaces are comprehensively characterized including evaluating surface roughness and extracting surface texture.

  17. EFFECT OF MINIMUM QUANTITY LUBRICATION ON SURFACE ROUGHNESS IN TOOL-BASED MICROMILLING

    Directory of Open Access Journals (Sweden)

    Mohammad Yeakub Ali

    2017-05-01

    Full Text Available Cutting fluid plays an important role in machining processes to achieve dimensional accuracy in reducing tool wear and improving the tool life. Conventional flood cooling method in machining processes is not cost effective and consumption of huge amount of cutting fluids is not healthy and environmental friendly. In micromachining, flood cooling is not recommended to avoid possible damage of the microstructures. Therefore, one of the alternatives to overcome the environmental issues to use minimum quantity of lubrication (MQL in machining process. MQL is eco-friendly and has economical advantage on manufacturing cost. However, there observed lack of study on MQL in improving machined surface roughness in micromilling. Study of the effects of MQL on surface roughness should be carried out because surface roughness is one of the important issues in micromachined parts such as microfluidic channels. This paper investigates and compares surface roughness with the presence of MQL and dry cutting in micromilling of aluminium alloy 1100 using DT-110 milling machine. The relationship among depth of cut, feed rate, and spindle speed on surface roughness is also analyzed. All three machining parameters identified as significant for surface roughness with dry cutting which are depth of cut, feed rate, and spindle speed. For surface roughness with MQL, it is found that spindle speed did not give much influence on surface roughness. The presence of MQL provides a better surface roughness by decreasing the friction between tool and workpiece.

  18. Toothbrushing alters the surface roughness and gloss of composite resin CAD/CAM blocks.

    Science.gov (United States)

    Kamonkhantikul, Krid; Arksornnukit, Mansuang; Lauvahutanon, Sasipin; Takahashi, Hidekazu

    2016-01-01

    This study investigated the surface roughness and gloss of composite resin CAD/CAM blocks after toothbrushing. Five composite resin blocks (Block HC, Cerasmart, Gradia Block, KZR-CAD Hybrid Resin Block, and Lava Ultimate), one hybrid ceramic (Vita Enamic), one feldspar ceramic (Vitablocs Mark II), one PMMA block (Telio CAD), and one conventional composite resin (Filtek Z350 XT) were evaluated. Surface roughness (Ra) and gloss were determined for each group of materials (n=6) after silicon carbide paper (P4000) grinding, 10k, 20k, and 40k toothbrushing cycles. One-way repeated measures ANOVA indicated significant differences in the Ra and gloss of each material except for the Ra of GRA. After 40k toothbrushing cycles, the Ra of BLO and TEL showed significant increases, while CER, KZR, ULT, and Z350 showed significant decreases. GRA, ENA, and VIT maintained their Ra. All of the materials tested, except CER, demonstrated significant decreases in gloss after 40k toothbrushing cycles.

  19. Polishing and toothbrushing alters the surface roughness and gloss of composite resins.

    Science.gov (United States)

    Kamonkhantikul, Krid; Arksornnukit, Mansuang; Takahashi, Hidekazu; Kanehira, Masafumi; Finger, Werner J

    2014-01-01

    This study aimed to investigate the surface roughness and gloss of composite resins after using two polishing systems and toothbrushing. Six composite resins (Durafill VS, Filtek Z250, Filtek Z350 XT, Kalore, Venus Diamond, and Venus Pearl) were evaluated after polishing with two polishing systems (Sof-Lex, Venus Supra) and after toothbrushing up to 40,000 cycles. Surface roughness (Ra) and gloss were determined for each composite resin group (n=6) after silicon carbide paper grinding, polishing, and toothbrushing. Two-way ANOVA indicated significant differences in both Ra and gloss between measuring stages for the composite resins tested, except Venus Pearl, which showed significant differences only in gloss. After polishing, the Filtek Z350 XT, Kalore, and Venus Diamond showed significant increases in Ra, while all composite resin groups except the Filtek Z350 XT and Durafill VS with Sof-Lex showed increases in gloss. After toothbrushing, all composite resin demonstrated increases in Ra and decreases in gloss.

  20. Effect of Polishing Systems on Surface Roughness and Topography of Monolithic Zirconia.

    Science.gov (United States)

    Goo, C L; Yap, Auj; Tan, Kbc; Fawzy, A S

    2016-01-01

    This study evaluated the effect of different chairside polishing systems on the surface roughness and topography of monolithic zirconia. Thirty-five monolithic zirconia specimens (Lava PLUS, 3M ESPE) were fabricated and divided into five groups of seven and polished with the following: Group 1 (WZ)-Dura white stone followed by Shofu zirconia polishing kit; Group 2 (SZ)-Shofu zirconia polishing kit; Group 3 (CE)-Ceramiste porcelain polishers; Group 4 (CM)-Ceramaster porcelain polishers; and Group 5 (KZ)-Komet ZR zirconia polishers. All specimens were ground with a fine-grit diamond bur prior to polishing procedures to simulate clinical finishing. Baseline and post-polishing profilometric readings were recorded and delta Ra values (difference in mean surface roughness before and after polishing) were computed and analyzed using one-way analysis of variance and Scheffe post hoc test (pzirconia.

  1. Eigenwave spectrum of surface acoustic waves on a rough self-affine fractal surface

    NARCIS (Netherlands)

    Palasantzas, George

    1994-01-01

    The propagation of a sound wave along a statistically rough solid-vacuum interface is investigated for the case of self-affine fractals. The wave-number relation ω=ω(k) is examined for the transverse polarized surface wave. The range of existence of this wave is analyzed as a function of the degree

  2. Effects of dimensional size and surface roughness on service performance for a micro Laval nozzle

    Science.gov (United States)

    Cai, Yukui; Liu, Zhanqiang; Shi, Zhenyu

    2017-05-01

    Nozzles with large and small dimensions are widely used in various industries. The main objective of this research is to investigate the effects of dimensional size and surface roughness on the service performance of a micro Laval nozzle. The variation of nozzle service performance from the conventional macro to micro scale is presented in this paper. This shows that the dimensional nozzle size has a serious effect on the nozzle gas flow friction. With the decrease of nozzle size, the velocity performance and thrust performance deteriorate. The micro nozzle performance has less sensitivity to the variation of surface roughness than the large scale nozzle does. Surface quality improvement and burr prevention technologies are proposed to reduce the friction effect on the micro nozzle performance. A novel process is then developed to control and depress the burr generation during micro nozzle machining. The polymethyl-methacrylate as a coating material is coated on the rough machined surface before finish machining. Finally, the micro nozzle with a throat diameter of 1 mm is machined successfully. Thrust test results show that the implement and application of this machining process benefit the service performance improvement of the micro nozzle.

  3. Effect of Bleaching Gels on Surface Roughness of Nanofilled Composite Resins

    Science.gov (United States)

    Wang, Linda; Francisconi, Luciana Fávaro; Atta, Maria Teresa; dos Santos, Jean Rodrigo; Del Padre, Natália Coelho; Gonini, Alcides; Fernandes, Karen Barros Parron

    2011-01-01

    Objectives: The aim of this study was to investigate the superficial texture of composite restorations after different bleaching protocols. Methods: Filtek Supreme (S), Filtek Z350 (F), and Grandio (G) were compared to Opallis (O) and Filtek Z250 (Z) (control microhybrid composites) and to bovine enamel using three different bleaching agents: 35% hydrogen peroxide Whiteness HP (WHP), 35% Whiteness HP MAXX (WMAXX) and 16% carbamide peroxide Whiteness Standard (WS). Six specimens from each composite were treated using each bleaching agent, according to the manufacturers’ instructions. Three random sites were measured for superficial roughness (Hommel Tester T 1000) weekly for each sample. Data were analyzed for each bleaching system using two-way ANOVA and Bonferroni tests at 5% significance level. Results: WHP treatment significantly altered the Filtek Supreme composite over time. When WMAXX was used, Grandio displayed the most significant alterations in surface roughness throughout the evaluation period, which was not observed for the other nanocomposites. Using WS, Filtek Z250 presented significant surface alterations over time, which was not seen in the nanofilled materials. Conclusions: Surface roughness alteration was material and time-dependent. The bleaching gels affected nanofilled and microhybrid composite resins. Enamel was the surface less affected by bleaching. PMID:21494385

  4. Effects of dimensional size and surface roughness on service performance for a micro Laval nozzle

    International Nuclear Information System (INIS)

    Cai, Yukui; Liu, Zhanqiang; Shi, Zhenyu

    2017-01-01

    Nozzles with large and small dimensions are widely used in various industries. The main objective of this research is to investigate the effects of dimensional size and surface roughness on the service performance of a micro Laval nozzle. The variation of nozzle service performance from the conventional macro to micro scale is presented in this paper. This shows that the dimensional nozzle size has a serious effect on the nozzle gas flow friction. With the decrease of nozzle size, the velocity performance and thrust performance deteriorate. The micro nozzle performance has less sensitivity to the variation of surface roughness than the large scale nozzle does. Surface quality improvement and burr prevention technologies are proposed to reduce the friction effect on the micro nozzle performance. A novel process is then developed to control and depress the burr generation during micro nozzle machining. The polymethyl-methacrylate as a coating material is coated on the rough machined surface before finish machining. Finally, the micro nozzle with a throat diameter of 1 mm is machined successfully. Thrust test results show that the implement and application of this machining process benefit the service performance improvement of the micro nozzle. (paper)

  5. Surface roughness of Ti6Al4V after heat treatment evaluated by artificial neural networks

    Energy Technology Data Exchange (ETDEWEB)

    Altug, Mehmet [Inonu Univ., Malataya (Turkey). Dept. of Machine and Metal Technologies; Erdem, Mehmet; Bozkir, Oguz [Inonu Univ., Malataya (Turkey); Ozay, Cetin [Univ. of Firat Elazig (Turkey). Faculty of Tech. Education

    2016-05-01

    The study examines how, using wire electrical discharge machining (WEDM), the microstructural, mechanical and conductivity characteristics of the titanium alloy Ti6Al4V are changed as a result of heat treatment and the effect they have on machinability. Scanning electron microscope (SEM), optical microscope and X-ray diffraction (XRD) examinations were performed to determine various characteristics and additionally related microhardness and conductivity measurements were conducted. L{sub 18} Taquchi test design was performed with three levels and six different parameters to determine the effect of such alterations on its machinability using WEDM and post-processing surface roughness (Ra) values were determined. Micro-changes were ensured successfully by using heat treatments. Results obtained with the optimization technique of artificial neural network (ANN) presented minimum surface roughness. Values obtained by using response surface method along with this equation were completely comparable with those achieved in the experiments. The best surface roughness value was obtained from sample D which had a tempered martensite structure.

  6. Effect of different polishing methods on surface roughness of provisional prosthetic materials.

    Science.gov (United States)

    Tupinambá, Ívian Verena Maia; Giampá, Priscila Couy Corrêa; Rocha, Isadora Almeida Rios; Lima, Emilena Maria Castor Xisto

    2018-01-01

    To evaluate the surface roughness of bis-acrylic and acrylic resins submitted to different methods of polishing. Fifty samples of each provisional restorative material (Structur 2, Protemp 4, Duralay, and Dencrilay) were fabricated (10 mm × 2 mm) and divided into five groups ( n = 10): (1) positive control group - polyester strip; (2) negative control - unpolished; (3) abrasive tips (Exa-Technique-Edenta); (4) goat hair brush and diamond polishing paste; and (5) silicone tips (Enhance). Each material was mixed and polymerized according to manufacturer's instructions. The parameter evaluated was the arithmetic mean of the surface roughness (Ra) determined using the rugosimeter SJ 301 (Mitutoyo, Japan). The data were analyzed with two-way analysis of variance ( post hoc Tukey's test) ( P < 0.05). The lowest surface roughness values (0,22-0,90 μm) were observed in the Group 4 - goat hair brush and diamond paste, while the highest values (1,17-1,44 μm) were found in the Group 5 - silicone tips (enhance), with statistically significant differences between them, except for Dencrilay acrylic resin. There was statistically significant difference between bis-acrylic and acrylic resins in the Groups 1, 2, and 4. Within the limitations of this study, it was concluded that the most effective polishing system was the goat hair brush with diamond paste for both bis-acrylic and acrylic resins. The bis-acrylic resins exhibited significantly smoother surfaces than the acrylic resins.

  7. The Influence of Surface Polish and Beverages on the Roughness of Nanohybrid and Microhybri Resin Composites

    Directory of Open Access Journals (Sweden)

    Sadeghi M

    2016-03-01

    Full Text Available Statement of the Problem: Surface roughness is a key factor in the aesthetics of restorative dentistry as it can determine the clinical quality and success of restorative materials. The chemical process of dissolution in the presence of mechanical forces can accelerate the surface roughness of tooth-coloured restorative materials. Objectives: To determine the degree of surface roughness of a microhybrid and a nanohybrid resin composite after polishing and immersion in various solutions. Materials and Methods: Two resin composites were used : a microhybrid (Gradia direct, GC, and a nanohybrid (Ice, SDI. A total of 54 disc-shaped specimens were prepared for each composite and immersed in distilled water incubated at 37 °C for 24 hours. After 24 h, the baseline measurement for surface roughness (Ra was performed and the specimens were divided into 3 groups of 18 and tested with unpolished or after polishing with Sof-Lex disc and Enhance point systems. Specimens in each group were subdivided into 3 subgroups (n = 6 and immersed in 3 solutions (distilled water, coffee, and cola for 7 days incubated at 37 °C. After 7 days, the specimens were rinsed with tap water for 10 seconds, dried with paper towel and Ra was measured again. Two randomly selected specimens of each group were sputter coated with gold and examined using a Field-Emission Scanning Electron Microscope (SEM. Results: Gradia direct showed a greater Ra than ice in all solutions for all polishing systems (p < 0.001. Specimens polished with Enhance point revealed a significantly greater roughness than Sof-Lex discs and both showed greater Ra than unpolished specimens. Specimens immersed in coffee exhibited significantly greater surface roughness than that of distilled water (p < 0.05 and cola (p < 0.001. Conclusions: Nano-hybrid composite showed a significantly smoother surface than microhybrid. Coffee exhibited the highest Ra compared to distilled water and cola. Enhance point revealed

  8. Exploration on Kerf-angle and Surface Roughness in Abrasive Waterjet Machining using Response Surface Method

    Science.gov (United States)

    Babu, Munuswamy Naresh; Muthukrishnan, Nambi

    2017-05-01

    Abrasive waterjet machining is a mechanical based unconventional cutting process which uses a mixture of abrasives and pressurized water as an intermediate to cut the material. The present paper focuses in analyzing the effect process parameters like feed rate, water pressure, standoff distance and abrasive flow rate on the surface roughness and kerf-angle of AISI 1018 mild steel experimentally. The experiments were performed under Taguchi's L27 orthogonal array. Moreover, the optimal parameter that significantly reduces the surface roughness and kerf-angle were calculated through response surface method. The most dominating process parameter that affects the responses was calculated by the Analysis of variance. In addition, machined surfaces are further subjected to scanning electron microscope (SEM) and atomic force microscope (AFM) for detailed study on the texture developed.

  9. Determination of surface roughness and topography of dental resin-based nanocomposites using AFM analysis

    Directory of Open Access Journals (Sweden)

    Tijana Lainović

    2013-02-01

    Full Text Available The aim of this study was to determine surface roughness and topography of polished dental resin-based nanocomposites.Four representative dental resin-based nanocomposites were tested in the study: two nanohybrids (Filtek Z550 and Tetric EvoCeram and two nanofilled (Filtek Ultimate Body and Filtek Ultimate Translucent; and two reference materials: one microfilled (Gradia Direct and one microhybrid (Filtek Z250. Polymerized cylindrical specimens (4 mm x 2 mm were polished with multi-step polishing system-Super Snap. Immediately after the polishing, topography of each specimen was examined by Veeco di CP-II Atomic Force Microscope. Specimen’s surface has been scanned in 6 points in contact mode with CONT20A-CP tips. 1 Hz scan rate and 256 x 256 resolution were used to obtain topography on a 90 μm x 90 μm scanning area. Measured topography data were processed by Image Processing and Data Analysis V2.1.15 software. Following parameters were compared among specimens: average roughness and maximum peak-to-valley distance.All of the tested materials had similar average surface roughness after finishing and polishing procedure. The lowest values occurred in the material Filtek Ultimate Body, and the highest in the Filtek Z550. When interpreting maximum peak-to-valley distance the larger differences in values (up to 100% occurred in Filtek Z550, Filtek Z250 and Filtek Ultimate Body, which is a result of the deep polishing channels and tracks. Type, size, distribution of fillers and filler loading in tested materials, didn’t influence average roughness values, but had an impact on maximum peak-to-valley distance values.

  10. Effect of sandblasting on surface roughness of zirconia-based ceramics and shear bond strength of veneering porcelain.

    Science.gov (United States)

    He, Min; Zhang, Zutai; Zheng, Dongxiang; Ding, Ning; Liu, Yan

    2014-01-01

    This study aims to investigate the effect of sandblasting on the surface roughness of zirconia and the shear bond strength of the veneering porcelain. Pre-sintered zirconia plates were prepared and divided into four groups. Group A were not treated at all; group B were first sandblasted under 0.2 MPa pressure and then densely sintered; group C and D were sintered first, and then sandblasted under 0.2 MPa and 0.4 MPa pressures respectively. Surface roughness was measured and 3D roughness was reconstructed for the specimens, which were also analyzed with X-ray diffractometry. Finally after veneering porcelain sintering, shear bond tests were conducted. Sandblasting zirconia before sintering significantly increased surface roughness and the shear bond strength between zirconia and veneering porcelain (pveneering porcelain.

  11. Relations between soil surface roughness, tortuosity, tillage treatments, rainfall intensity and soil and water losses from a red yellow latosol

    Directory of Open Access Journals (Sweden)

    Julieta Bramorski

    2012-08-01

    Full Text Available The soil surface roughness increases water retention and infiltration, reduces the runoff volume and speed and influences soil losses by water erosion. Similarly to other parameters, soil roughness is affected by the tillage system and rainfall volume. Based on these assumptions, the main purpose of this study was to evaluate the effect of tillage treatments on soil surface roughness (RR and tortuosity (T and to investigate the relationship with soil and water losses in a series of simulated rainfall events. The field study was carried out at the experimental station of EMBRAPA Southeastern Cattle Research Center in São Carlos (Fazenda Canchim, in São Paulo State, Brazil. Experimental plots of 33 m² were treated with two tillage practices in three replications, consisting of: untilled (no-tillage soil (NTS and conventionally tilled (plowing plus double disking soil (CTS. Three successive simulated rain tests were applied in 24 h intervals. The three tests consisted of a first rain of 30 mm/h, a second of 30 mm/h and a third rain of 70 mm/h. Immediately after tilling and each rain simulation test, the surface roughness was measured, using a laser profile meter. The tillage treatments induced significant changes in soil surface roughness and tortuosity, demonstrating the importance of the tillage system for the physical surface conditions, favoring water retention and infiltration in the soil. The increase in surface roughness by the tillage treatments was considerably greater than its reduction by rain action. The surface roughness and tortuosity had more influence on the soil volume lost by surface runoff than in the conventional treatment. Possibly, other variables influenced soil and water losses from the no-tillage treatments, e.g., soil type, declivity, slope length, among others not analyzed in this study.

  12. Effect of sealant agents on the color stability and surface roughness of nanohybrid composite resins.

    Science.gov (United States)

    Dede, Doğu Ömür; Şahin, Onur; Koroglu, Aysegül; Yilmaz, Burak

    2016-07-01

    The effect of sealant agents on the surface roughness and color stability of nanohybrid composite resins is unknown. The purpose of this in vitro study was to evaluate the effect of sealant agents on the surface roughness and color stability of 4 nanohybrid composite resin materials. Forty disks (10×2 mm) were fabricated for each nanohybrid composite resin material (Z-550, Tetric EvoCeram, Clearfill Majesty, Ice) (N=160) and divided into 4 surface treatment groups: 1 conventional polishing (control) and 3 different sealant agent (Palaseal, Optiglaze, BisCover) coupling groups (n=10). The specimens were thermocycled, and surface roughness (Ra) values were obtained with a profilometer. Scanning electron microscope images were also recorded. CIELab color parameters of each specimen were measured with a spectrophotometer before and after 7 days of storage in a coffee solution. Color differences were calculated by the CIEDE 2000 (ΔE00) formula. The data were statistically analyzed by 2-way ANOVA and by the Tukey HSD test (α=.05). The surface treatment technique significantly affected the Ra values of the composite resins tested (Pcomposite resin material was also significant for ΔE00 values (Pcomposite resin groups, significant decreases in Ra were observed only for the Palaseal agent coupled composite resin groups (except Ice) compared with the control groups (Pcomposite resin group, except for BisCover applied Clearfill Majesty (Pcomposite resin groups, significant differences were observed between the color change seen with BisCover and other sealants for Clearfill Majesty composite resin (Pcomposite resins except for Ice produced smoother surfaces. All surface sealant agents provided less discoloration of nanohybrid composite resins after coffee staining compared with conventional polishing except for BisCover applied Clearfill Majesty composite resin. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All

  13. Superficial roughness on composite surface, composite enamel and composite dentin junctions after different finishing and polishing procedures. Part I: roughness after treatments with tungsten carbide vs diamond burs.

    Science.gov (United States)

    Ferraris, Federico; Conti, Alessandro

    2014-01-01

    The aim of this study is to investigate different instruments for finishing composite restorations, as well as examining different surfaces and interfaces of the same restoration. The null hypothesis is represented by the fact that there are no significant differences on roughness of composite restorations finishing between tungsten carbide and diamond burs, furthermore the null hypothesis is that there are no significant differences on roughness between finishing on composite surfaces (C), compositeenamel (CE) and composite-dentin (CD) interfaces. The study was performed on 28 teeth, and class V cavities were prepared on the extracted teeth. Restorations were done in Filtek XTE nanofilled composite (3M Espe) in a standardized method, to then be finished. A comparison was made in the phase 1 between tungsten carbide burs (16 blades), diamond burs (46 μm), with a similar shape by the same manufacturer (Komet). Each surface received 5 bur applications. Consequently, an analysis with a profilometer was performed. Phase 2 involved further confrontation of ulterior finishing with ultrafine tungsten carbide burs (30 blades) and with extra and ultrafine diamond burs (25 and 8 μm) (the same shape as previously mentioned). A second analysis was then performed with a profilometer. All measurements were taken on C surfaces, CE and CD interfaces. Statistical analyses were carried out with c2 test (a = 0.05). The finishing procedures with fine grit or toothing burs gave a better smoothness with tungsten carbide burs compared to diamond burs. While with the ultrafine grit no significant differences were noted between tungsten carbide and diamond burs on the CE and CD interfaces, the diamond bur left less superficial roughness on the C surfaces. With regards to the superficial roughness of the different areas of restoration, it can be concluded that: minor roughness was detected on C surfaces, while the CD interface had the most superficial roughness, regardless of whether the

  14. Detection of a periodic structure embedded in surface roughness, for ...

    Indian Academy of Sciences (India)

    Intensities for different roughness situations. For strong roughness, we have g ≫ 1 and we can thus approximate exp(−g[1 − p (r)]) ≈ exp[− (r/r0)β],. (10) where r0 = l/g1/β. This indicates that for the same values of l and g the correlation length r0 is smaller for larger β, for g ≫ 1. It can be seen that on using the approximation, ...

  15. Measuring grinding surface roughness based on the sharpness evaluation of colour images

    International Nuclear Information System (INIS)

    Huaian, Y I; Jian, L I U; Enhui, L U; Peng, A O

    2016-01-01

    Current machine vision-based detection methods for metal surface roughness mainly use the grey values of images for statistical analysis but do not make full use of the colour information and ignore the subjective judgment of the human vision system. To address these problems, this paper proposes a method to measure surface roughness through the sharpness evaluation of colour images. Based on the difference in sharpness of virtual images of colour blocks that are formed on grinding surfaces with different roughness, an algorithm for evaluating the sharpness of colour images that is based on the difference of the RGB colour space was used to develop a correlation model between the sharpness and the surface roughness. The correlation model was analysed under two conditions: constant illumination and varying illumination. The effect of the surface textures of the grinding samples on the image sharpness was also considered, demonstrating the feasibility of the detection method. The results show that the sharpness is strongly correlated with the surface roughness; when the illumination and the surface texture have the same orientation, the sharpness clearly decreases with increasing surface roughness. Under varying illumination, this correlation between the sharpness and surface roughness was highly robust, and the sharpness of each virtual image increased linearly with the illumination. Relative to the detection method for surface roughness using gray level co-occurrence matrix or artificial neural network, the proposed method is convenient, highly accurate and has a wide measurement range. (paper)

  16. Electromagnetic Scattering from Rough Sea Surface with PM Spectrum Covered by an Organic Film

    International Nuclear Information System (INIS)

    Wang Rui; Guo Li-Xin; Wang An-Qi; Wu Zhen-Sen

    2011-01-01

    The rough sea surface covered by an organic film will cause attenuation of capillarity waves, which implies that the organic films play an important role in rough sea surface processes. We focus on a one-dimensional (1D) rough sea surface with the Pierson—Moskowitz (PM) spectrum distributed to the homogeneous insoluble organic slicks. First, the impact of the organic film on the PM surface spectrum is presented, as well as that of the correlation length, the rms height and slope of the rough sea surface. The damping effect of the organic film changes the physical parameters of the rough sea surface. For example, the organic film will reduce the rms height and slopee of the rough sea surface, which results in the attenuation of the high-frequency components of the PM spectrum leading to modification of the surface PM spectrum. Then, the influence of the organic film on the electromagnetic (EM) scattering coefficients from PM rough sea surface covered by the organic film is investigated and discussed in detail, compared with the clean PM rough sea surface through the method of moments. (fundamental areas of phenomenology(including applications))

  17. Effects of irregular two-dimensional and three-dimensional surface roughness in turbulent channel flows

    International Nuclear Information System (INIS)

    De Marchis, M.; Napoli, E.

    2012-01-01

    Highlights: ► 3D irregular rough surfaces produce higher effects than those observed over 2D. ► Effective slope is a geometrical parameter representative of the roughness effects. ► 3D rough surfaces enhance the turbulence isotropization. ► 2D and 3D irregular roughness partially support the wall similarity. ► Irregular rough surfaces shear some features with regular rough walls. - Abstract: Wall-resolved Large Eddy Simulation of fully developed turbulent channel flows over two different rough surfaces is performed to investigate on the effects of irregular 2D and 3D roughness on the turbulence. The two geometries are obtained through the superimposition of sinusoidal functions having random amplitudes and different wave lengths. In the 2D configuration the irregular shape in the longitudinal direction is replicated in the transverse one, while in the 3D case the sinusoidal functions are generated both in streamwise and spanwise directions. Both channel walls are roughened in such a way as to obtain surfaces with statistically equivalent roughness height, but different shapes. In order to compare the turbulence properties over the two rough walls and to analyse the differences with a smooth wall, the simulations are performed at the same Reynolds number Re τ = 395. The same mean roughness height h = 0.05δ (δ the half channel height) is used for the rough walls. The roughness function obtained with the 3D roughness is larger than in the 2D case, although the two walls share the same mean height. Thus, the considered irregular 3D roughness is more effective in reducing the flow velocity with respect to the 2D roughness, coherently with the literature results that identified a clear dependence of the roughness function on the effective slope (see ), higher in the generated 3D rough wall. The analysis of higher-order statistics shows that the effects of the roughness, independently on its two- or three-dimensional shape, are mainly confined in the inner

  18. Noncontact Surface Roughness Estimation Using 2D Complex Wavelet Enhanced ResNet for Intelligent Evaluation of Milled Metal Surface Quality

    Directory of Open Access Journals (Sweden)

    Weifang Sun

    2018-03-01

    Full Text Available Machined surfaces are rough from a microscopic perspective no matter how finely they are finished. Surface roughness is an important factor to consider during production quality control. Using modern techniques, surface roughness measurements are beneficial for improving machining quality. With optical imaging of machined surfaces as input, a convolutional neural network (CNN can be utilized as an effective way to characterize hierarchical features without prior knowledge. In this paper, a novel method based on CNN is proposed for making intelligent surface roughness identifications. The technical scheme incorporates there elements: texture skew correction, image filtering, and intelligent neural network learning. Firstly, a texture skew correction algorithm, based on an improved Sobel operator and Hough transform, is applied such that surface texture directions can be adjusted. Secondly, two-dimensional (2D dual tree complex wavelet transform (DTCWT is employed to retrieve surface topology information, which is more effective for feature classifications. In addition, residual network (ResNet is utilized to ensure automatic recognition of the filtered texture features. The proposed method has verified its feasibility as well as its effectiveness in actual surface roughness estimation experiments using the material of spheroidal graphite cast iron 500-7 in an agricultural machinery manufacturing company. Testing results demonstrate the proposed method has achieved high-precision surface roughness estimation.

  19. Fractal Surfaces of Molecular Crystals Mimicking Lotus Leaf with Phototunable Double Roughness Structures.

    Science.gov (United States)

    Nishimura, Ryo; Hyodo, Kengo; Sawaguchi, Haruna; Yamamoto, Yoshiaki; Nonomura, Yoshimune; Mayama, Hiroyuki; Yokojima, Satoshi; Nakamura, Shinichiro; Uchida, Kingo

    2016-08-17

    Double roughness structure, the origin of the lotus effect of natural lotus leaf, was successfully reproduced on a diarylethene microcrystalline surface. Static superwater-repellency and dynamic water-drop-bouncing were observed on the surface, in the manner of natural lotus leaves. Double roughness structure was essential for water-drop-bouncing. This ability was not observed on a single roughness microcrystalline surface showing the lotus effect of the same diarylethene derivative. The double roughness structure was reversibly controlled by alternating irradiation with UV and visible light.

  20. The influence of mouthrinses and simulated toothbrushing on the surface roughness of a nanofilled composite resin.

    Science.gov (United States)

    Trauth, Keico Graciela Sano; Godoi, Ana Paula Terossi de; Colucci, Vivian; Corona, Silmara Aparecida Milori; Catirse, Alma Blásida Concepción Elizaur Benitez

    2012-01-01

    The aim of this study was to determine the influence of mouthrinses on the surface roughness of a nanofilled composite resin after toothbrushing. One hundred nanofilled composite resin specimens were prepared and randomly distributed into two groups-brushed and non-brushed-and then assigned to five subgroups, according to the mouthrinse solutions (n = 10): Colgate Plax Fresh Mint, Oral B, Cepacol, Colgate Plax, and artificial saliva. Each sample was immersed in 20 mL of the mouthrinses for 1 minute, 5 days per week, twice a day, for a 3-week period. The control group used in the study was one in which the specimens were not subjected to brushing and remained only in artificial saliva. Toothbrushing was performed once a week for 1 minute, for 3 weeks. Surface roughness measurements (Ra) were performed after the immersion period and toothbrushing, by means of a profilometer. Data were analyzed by two-way ANOVA and Tukey's test. Analysis revealed that the association between toothbrushing and Colgate Plax Fresh Mint produced the lowest surface roughness (p toothbrushing or not (p toothbrushing.

  1. Changes in the surface roughness and friction coefficient of orthodontic bracket slots before and after treatment.

    Science.gov (United States)

    Liu, Xiaomo; Lin, Jiuxiang; Ding, Peng

    2013-01-01

    In this study, we tested the surface roughness of bracket slots and the friction coefficient between the bracket and the stainless steel archwire before and after orthodontic treatment. There were four experimental groups: groups 1 and 2 were 3M new and retrieved brackets, respectively, and groups 3 and 4 were BioQuick new and retrieved brackets, respectively. All retrieved brackets were taken from patients with the first premolar extraction and using sliding mechanics to close the extraction space. The surface roughness of specimens was evaluated using an optical interferometry profilometer, which is faster and nondestructive compared with a stylus profilometer, and provided a larger field, needing no sample preparation, compared with atomic force microscopy. Orthodontic treatment resulted in significant increases in surface roughness and coefficient of friction for both brands of brackets. However, there was no significant difference by brand for new or retrieved brackets. These retrieval analysis results highlight the necessity of reevaluating the properties and clinical behavior of brackets during treatment to make appropriate treatment decisions. © Wiley Periodicals, Inc.

  2. Bone response to immediate loading through titanium implants with different surface roughness in rats.

    Science.gov (United States)

    Sato, Naoko; Kuwana, Toshie; Yamamoto, Miou; Suenaga, Hanako; Anada, Takahisa; Koyama, Shigeto; Suzuki, Osamu; Sasaki, Keiichi

    2014-07-01

    Because of its high predictability of success, implant therapy is a reliable treatment for replacement of missing teeth. The concept of immediate implant loading has been widely accepted in terms of early esthetic and functional recovery. However, there is little biological evidence to support this concept. The objective of this study was to examine the interactive effects of mechanical loading and surface roughness of immediately loaded titanium implants on bone formation in rats. Screw-shaped anodized titanium implants were either untreated (smooth) or acid-etched. Two implants were inserted parallel to each other in the tibiae of rats, and a closed coil spring (2.0 N) was immediately applied. Trabecular and cortical bone around both implants was analyzed using microtomographic images, and a removal torque test was performed at weeks 1, 2, and 4. Immediate loading of acid-etched implants resulted in significant decreases in bone mineral density, contact surface area, and cortical bone thickness. These effects were not observed after immediate loading of smooth implants. Conversely, loading did not influence acid-etched implant fixation; however, smooth implant fixation at week 1 was significantly reduced. These results imply that surface roughness regulates bone response to mechanical stress and that immediate loading might not inhibit osseointegration for smooth and rough implants in the late healing stages.

  3. Measuring the surface roughness of geological rock surfaces in SAR data using fractal geometry

    Science.gov (United States)

    Ghafouri, Ali; Amini, Jalal; Dehmollaian, Mojtaba; Kavoosi, Mohammad Ali

    2017-05-01

    Determining surface morphology using synthetic aperture radar (SAR) data requires accurate topographic and microtopographic models. To distinguish different surface geometric patterns and to differentiate the formation of geological rock surfaces, it is necessary to model the smoothness and roughness of surfaces based on radar signal backscattering. Euclidean geometry is less able than fractal geometry to describe natural phenomena; however, in application to radar backscattering models, fractal geometry has never fully replaced Euclidean geometry. Using fractal geometry only, this paper attempts to improve the backscattering simulation generated by an Integral Equation Model to improve the description of geological rock surfaces. As the application of radar signal backscattering is a rarity in the domain of geology, the paper also discusses the efficiency of the method in improving the results of conventional geological mapping methods. The proposed method is applied to the Anaran geological formation (between Dehloran and Ilam in IRAN) using TerraSAR-X SAR data and in situ roughness measurements on pure sites with rough, intermediate, and smooth morphologies. This implementation shows fractal and diffractal behavior of geological morphologies under various conditions.

  4. Effects of 2 polishing techniques and reglazing on the surface roughness of dental porcelain.

    Science.gov (United States)

    Schneider, Jacqueline; Dias Frota, Bruna Marjorie; Passos, Vanara Florencio; Santiago, Sergio Lima; Freitas Pontes, Karina Matthes de

    2013-01-01

    The aim of this study was to compare the effect of 2 polishing systems and reglazing of dental porcelain through a quantitative and qualitative analysis of surface roughness using a stylus profilometer and scanning electron microscope. Fifteen porcelain specimens (10 x 3 x 3 mm) were used. On 1 surface of each block, a layer of glaze was applied, and surface roughness (Ra) was analyzed. All specimens were ground with aluminum oxide sandpaper until the shine was removed and the resulting Ra values were obtained. Afterwards, they were randomly divided into 3 treatment groups (n = 5): Group I (GI), polished with diamond-impregnated rubber wheels; Group II (GII), polished with silicon carbide-impregnated rubber wheels; and Group III (GIII), reglazed firing procedure alone. After the treatments, new Ra measurements were done. Data were submitted to analysis of variance (ANOVA), and Tukey tests at 5%. Comparisons between ground surface and treated surface were made by paired t-test. The ground and treated Ra values (µm) were determined as follows: GI: 0.66 ± 0.14, 0.35 ± 0.06; GII: 0.60 ± 0.04, 0.09 ± 0.03; and GIII: 0.67 ± 0.05, 0.75 ± 0.24. Significant differences were found between the ground and treated values for all groups. After the treatments, all groups differed statistically (P rubber or reglazing alone were not able to achieve a satisfactory smoothness.

  5. Effects of surface roughness and electrokinetic heterogeneity on electroosmotic flow in microchannel

    Energy Technology Data Exchange (ETDEWEB)

    Masilamani, Kannan; Ganguly, Suvankar; Feichtinger, Christian; Bartuschat, Dominik; Rüde, Ulrich, E-mail: suva_112@yahoo.co.in [Department of Computer Science 10 University of Erlangen-Nuremberg, Cauerstr.11 91058 Erlangen (Germany)

    2015-06-15

    In this paper, a hybrid lattice-Boltzmann and finite-difference (LB-FD) model is applied to simulate the effects of three-dimensional surface roughness and electrokinetic heterogeneity on electroosmotic flow (EOF) in a microchannel. The lattice-Boltzmann (LB) method has been employed to obtain the flow field and a finite-difference (FD) method is used to solve the Poisson-Boltzmann (PB) equation for the electrostatic potential distribution. Numerical simulation of flow through a square cross-section microchannel with designed roughness is conducted and the results are critically analysed. The effects of surface heterogeneity on the electroosmotic transport are investigated for different roughness height, width, roughness interval spacing, and roughness surface potential. Numerical simulations reveal that the presence of surface roughness changes the nature of electroosmotic transport through the microchannel. It is found that the electroosmotic velocity decreases with the increase in roughness height and the velocity profile becomes asymmetric. For the same height of the roughness elements, the EOF velocity rises with the increase in roughness width. For the heterogeneously charged rough channel, the velocity profile shows a distinct deviation from the conventional plug-like flow pattern. The simulation results also indicate locally induced flow vortices which can be utilized to enhance the flow and mixing within the microchannel. The present study has important implications towards electrokinetic flow control in the microchannel, and can provide an efficient way to design a microfluidic system of practical interest. (paper)

  6. In situ evaluation of surface roughness and micromorphology of temporary soft denture liner materials at different time intervals.

    Science.gov (United States)

    Araújo, Célio U; Basting, Roberta T

    2018-03-01

    To perform an in situ evaluation of surface roughness and micromorphology of two soft liner materials for dentures at different time intervals. The surface roughness of materials may influence the adhesion of micro-organisms and inflammation of the mucosal tissues. The in situ evaluation of surface roughness and the micromorphology of soft liner materials over the course of time may present results different from those of in vitro studies, considering the constant presence of saliva and food, the changes in temperature and the pH level in the oral cavity. Forty-eight rectangular specimens of each of the two soft liner materials were fabricated: a silicone-based material (Mucopren Soft) and an acrylic resin-based material (Trusoft). The specimens were placed in the dentures of 12 participants (n = 12), and the materials were evaluated for surface roughness and micromorphology at different time intervals: 0, 7, 30 and 60 days. Roughness (Ra) was evaluated by means of a roughness tester. Surface micromorphology was evaluated by scanning electron microscopy. Analysis of variance for randomised block design and Tukey's test showed that surface roughness values were lower in the groups using the silicone-based material at all the time intervals (P < .0001). The average surface roughness was higher at time interval 0 than at the other intervals, for both materials (P < .0001). The surface micromorphology showed that the silicone material presented a more regular and smoother surface than the acrylic resin-based material. The surface roughness of acrylic resin-based and silicone-based denture soft liner materials decreased after 7 days of evaluation, leading to a smoother surface over time. The silicone-based material showed lower roughness values and a smoother surface than the acrylic resin-based material, thereby making it preferred when selecting more appropriate material, due its tendency to promote less biofilm build-up. © 2017 John Wiley & Sons A/S and The

  7. Influence of surface roughness skewness on rolling contact fatigue life

    Science.gov (United States)

    Akamatsu, Yoshinobu; Tsushima, Noriyuki; Goto, Toshihide; Hibi, Kenji

    1992-10-01

    This paper evaluates the effects of randomly distributed small indentations, or pits, on the lubricating properties when operating under these mixed or boundary lubrication conditions. Rings and needle rollers were textured with randomly distributed small indentations, or pits, for evaluation. Skewness (Sk) was used as a measure of surface finish to characterize the degree to which the material of these modified parts was above the mean line, a positive value, or below the mean line, a negative value. Fatigue life tests were conducted on these rolling elements, whose skewness ranged from -1.2 to -2.0, under mixed or boundary lubrication conditions. Test results showed rolling bearing fatigue life to increase with a decrease in skewness as related to the depth, width, and distribution of the surface indentations, or pits, on the parts.

  8. An In Vitro Evaluation of Alumina, Zirconia, and Lithium Disilicate Surface Roughness Caused by Two Scaling Instruments.

    Science.gov (United States)

    Vigolo, Paolo; Buzzo, Ottavia; Buzzo, Maurizio; Mutinelli, Sabrina

    2017-02-01

    Plaque control is crucial for the prevention of inflammatory periodontal disease. Hand scaling instruments have been shown to be efficient for the removal of plaque; however, routine periodontal prophylactic procedures may modify the surface profile of restorative materials. The purpose of this study was to assess in vitro the changes in roughness of alumina, zirconia, and lithium disilicate surfaces treated by two hand scaling instruments. Forty-eight alumina specimens, 48 zirconia specimens, and 48 lithium disilicate specimens, were selected. All specimens were divided into three groups of 16 each; one group for each material was considered the control group and no scaling procedures were performed; the second group of each material was exposed to scaling with steel curettes simulating standard clinical conditions; the third group of each material was exposed to scaling with titanium curettes. After scaling, the surface roughness of the specimens was evaluated with a profilometer. First, a statistical test was carried out to evaluate the difference in surface roughness before the scaling procedure of the three materials was effected (Kruskal-Wallis test). Subsequently, the effect of curette material (steel and titanium) on roughness difference and roughness ratio was analyzed throughout the entire sample and within each material group, and a nonparametric test for dependent values was conducted (Wilcoxon signed-rank test). Finally, the roughness ratios of the three material groups were compared by means of a Kruskal-Wallis test and a Wilcoxon signed-rank test. Upon completion of profilometric evaluation, representative specimens from each group were prepared for SEM evaluation to evaluate the effects of the two scaling systems on the different surfaces qualitatively. After scaling procedure, the roughness profile value increased in all disks. Classifying the full sample according to curette used, the roughness of the disks treated with a steel curette reached a

  9. Impact of surface roughness on the debonding mechanism in concrete repairs

    NARCIS (Netherlands)

    Lukovic, M.; Schlangen, H.E.J.G.; Ye, G.; Savija, B.

    2013-01-01

    Surface roughness of the existing concrete substrate was considered to have the greatest impact on the bond strength in repair systems. However, the influence of this parameter has been subject for debates in recent years. The effect of concrete surface roughness is not quite clear, nor there exist

  10. USING MULTI-DIMENSIONAL MICROWAVE REMOTE SENSING INFORMATION FOR THE RETRIEVAL OF SOIL SURFACE ROUGHNESS

    Directory of Open Access Journals (Sweden)

    P. Marzahn

    2016-06-01

    Full Text Available In this Paper the potential of multi parametric polarimetric SAR (PolSAR data for soil surface roughness estimation is investigated and its potential for hydrological modeling is evaluated. The study utilizes microwave backscatter collected from the Demmin testsite in the North-East Germany during AgriSAR 2006 campaign using fully polarimetric L-Band airborne SAR data. For ground truthing extensive soil surface roughness in addition to various other soil physical properties measurements were carried out using photogrammetric image matching techniques. The correlation between ground truth roughness indices and three well established polarimetric roughness estimators showed only good results for Re[ρRRLL] and the RMS Height s. Results in form of multitemporal roughness maps showed only satisfying results due to the fact that the presence and development of particular plants affected the derivation. However roughness derivation for bare soil surfaces showed promising results.

  11. Effects of soil surface roughness on interrill erosion processes and sediment particle size distribution

    Science.gov (United States)

    Ding, Wenfeng; Huang, Chihua

    2017-10-01

    Soil surface roughness significantly impacts runoff and erosion under rainfall. Few previous studies on runoff generation focused on the effects of soil surface roughness on the sediment particle size distribution (PSD), which greatly affects interrill erosion and sedimentation processes. To address this issue, a rainfall-simulation experiment was conducted with treatments that included two different initial soil surface roughnesses and two rainfall intensities. Soil surface roughness was determined by using photogrammetric method. For each simulated event, runoff and sediment samples were collected at different experimental times. The effective (undispersed) PSD of each sediment sample and the ultimate (after dispersion) PSD were used to investigate the detachment and transport mechanisms involved in sediment movement. The results show that soil surface roughness significantly delayed runoff initiation, but had no significant effect on the steady runoff rate. However, a significant difference in the soil loss rate was observed between the smooth and rough soil surfaces. Sediments from smooth soil surfaces were more depleted in clay-size particles, but more enriched in sand-size particles than those from rough soil surfaces, suggesting that erosion was less selective on smooth than on rough soil surfaces. The ratio of different sizes of transported sediment to the soil matrix indicates that most of the clay was eroded in the form of aggregates, silt-size particles were transported mainly as primary particles, and sand-size particles were predominantly aggregates of finer particles. Soil surface roughness has a crucial effect on the sediment size distribution and erosion processes. Significant differences of the enrichment ratios for the effective PSD and the ultimate PSD were observed under the two soil surface roughness treatments. These findings demonstrate that we should consider each particle size separately rather than use only the total sediment discharge in

  12. A non-contact 3D method to characterize the surface roughness of castings

    DEFF Research Database (Denmark)

    Nwaogu, Ugochukwu Chibuzoh; Tiedje, Niels Skat; Hansen, Hans Nørgaard

    2013-01-01

    A non-contact technique using a 3D optical system was used to measure the surface roughness of two selected standard surface roughness comparators used in the foundry industry. Profile and areal analyses were performed using scanning probe image processor (SPIP) software. The results show that th...... and the surface roughness parameter (Sa) values were compared with those of the standards. Sa parameter suffices for the evaluation of casting surface texture. The S series comparators showed a better description of the surface of castings after shot blasting than the A series....

  13. Influence of polishing on surface roughness following toothbrushing wear of composite resins.

    Science.gov (United States)

    Dalla-Vecchia, Karine Battestin; Taborda, Talita Damas; Stona, Deborah; Pressi, Heloísa; Burnett Júnior, Luiz Henrique; Rodrigues-Junior, Sinval Adalberto

    2017-01-01

    This study aimed to evaluate the influence of different polishing systems on the surface roughness of composite resins following procedures to simulate the effects of toothbrushing over time. Four currently available commercial composites were used to make 128 cylindrical specimens. The specimens were randomly allocated to polishing with a 1-step polisher or 1 of 3 multistep polishers (n = 8 per group). The baseline surface roughness was measured, and the specimens were submitted to 5000, 10,000, and 20,000 brushing cycles to represent toothbrushing throughout 6, 12, and 24 months, respectively. Results showed that surface roughness was influenced by the type of composite and polishing system and was not influenced by the simulated toothbrushing time. However, the surface roughness, as challenged by toothbrushing wear, was affected by the interaction among the composite, the polisher, and the toothbrushing time. The 1-step polisher produced the highest surface roughness and influenced toothbrushing wear resistance of some composites.

  14. Surface roughness effects on plasma near a divertor plate and local impact angle

    Directory of Open Access Journals (Sweden)

    Wanpeng Hu

    2017-08-01

    Full Text Available The impact of rough surface topography on the electric potential and electric field is generally neglected due to the small scale of surface roughness compared to the width of the plasma sheath. However, the distributions of the electric potential and field on rough surfaces are expected to influence the characteristics of edge plasma and the local impact angle. The distributions of plasma sheath and local impact angle on rough surfaces are investigated by a two dimension-in-space and three dimension-in-velocity (2d3v Particle-In-Cell (PIC code. The influences of the plasma temperature andsurface morphology on the plasma sheath, local impact angle and resulting physical sputtering yield on rough surfaces are investigated.

  15. Separate effects of surface roughness, wettability and nano-porosity on the Leidenfrost point temperature of water

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Hyung Dae [Kyunghee University, Yongin (Korea, Republic of)

    2011-05-15

    Quenching phenomena play a key role in LWR safety, particularly in the reflood phase of a large-break LOCA. It is well known that quenching phenomena are affected by the physico-chemical characteristics of the hot surface, such as surface roughness, wettability and porosity. However, while some general qualitative trends are known, there is a lack of quantitative data on the relative importance and magnitude of these effects. Therefore, we conduct water-droplet Leidenfrost Point (LFP) tests using custom-fabricated surfaces for which roughness, wettability and porosity were controlled accurately and separately at the nanoscale

  16. Effects of surface roughness and film thickness on the adhesion of a bioinspired nanofilm

    Science.gov (United States)

    Peng, Z. L.; Chen, S. H.

    2011-05-01

    Inspired by the gecko's climbing ability, adhesion between an elastic nanofilm with finite length and a rough substrate with sinusoidal roughness is studied in the present paper, considering the effects of substrate roughness and film thickness. It demonstrates that the normal adhesion force of the nanofilm on a rough substrate depends significantly on the geometrical parameters of the substrate. When the film length is larger than the wavelength of the sinusoidal roughness of the substrate, the normal adhesion force decreases with increasing surface roughness, while the normal adhesion force initially decreases then increases if the wavelength of roughness is larger than the film length. This finding is qualitatively consistent with a previously interesting experimental observation in which the adhesion force of the gecko spatula is found to reduce significantly at an intermediate roughness. Furthermore, it is inferred that the gecko may achieve an optimal spatula thickness not only to follow rough surfaces, but also to saturate the adhesion force. The results in this paper may be helpful for understanding how geckos overcome the influence of natural surface roughness and possess such adhesion to support their weights.

  17. On the Concept of Electrode to Discharge Phenomena in Surface Roughness With Reference Strongly Electronegative Gases

    DEFF Research Database (Denmark)

    McAllister, Iain Wilson

    1986-01-01

    The use of geometrically well-defined protrusions in studies es of the effects of electrode surface roughness upon the insulation strength of strongly electronegative gases is discussed. It is argued that, with respect to the roughness associated with production processes, the dimensions of artif......The use of geometrically well-defined protrusions in studies es of the effects of electrode surface roughness upon the insulation strength of strongly electronegative gases is discussed. It is argued that, with respect to the roughness associated with production processes, the dimensions...

  18. Evaluation of surface roughness of three different composite resins with three different polishing systems.

    Science.gov (United States)

    Abzal, Mohammed S; Rathakrishnan, Mensudar; Prakash, Venkatachalam; Vivekanandhan, Paramasivam; Subbiya, Arunajatesan; Sukumaran, Vridhachalam Ganapathy

    2016-01-01

    The aim of this study was to evaluate the surface roughness of three composites with three different polishing systems. Composite specimens were made from the Teflon mold with a standardized cavity size (6 mm diameter and 3 mm height). Group I - Filtek Z350XT (Nano clusters), group II - T-Econom plus (Microhybrid), group III - G-aenial Flo (True Nano). The samples were cured for 30 s from both sides with the matrices in place. The 60 samples were divided into 3 groups (N = 20), which accounted for 40 surfaces, (n = 20 × 2 = 40) in each groups. Each group were subdivided into four subgroups based on the type polishing material, subgroup A - Control, subgroup B - Astrobrush, subgroup C - Astropol, and subgroup D - Soflex spiral wheel. The samples of all groups except group A (control) were finished and polished according to the manufacture's instruction. After polishing, the roughness (Ra) of the resin composite of all the specimens were measured using a profilometer. Soflex spiral wheel (group D) significantly had the least roughness (Ra) value as compared to the other groups. Among the three resin composites tested, G-aenial Flo exhibited least Ra value due to its reduced filler size and its uniform distribution.

  19. Minimal alterations on the enamel surface by micro-abrasion: in vitro roughness and wear assessments

    Directory of Open Access Journals (Sweden)

    Marcela Charantola Rodrigues

    2013-04-01

    Full Text Available Objective: To evaluate the in vitro changes on the enamel surface after a micro-abrasion treatment promoted by different products. Material and Methods: Fifty (50 fragments of bovine enamel (15 mm × 5 mm were randomly assigned to five groups (n=10 according to the product utilized: G1 (control= silicone polisher (TDV, G2= 37% phosphoric acid (3M/ESPE + pumice stone (SS White, G3= Micropol (DMC Equipment, G4= Opalustre (Ultradent and G5= Whiteness RM (FGM Dental Products. Roughness and wear were the responsible variables used to analyze these surfaces in four stages: baseline, 60 s and 120 s after the micro-abrasion and after polishing, using a Hommel Tester T1000 device. After the tests, a normal distribution of data was verified, with repeated ANOVA analyses (p≤0.05 which were used to compare each product in different stages. One-way ANOVA and Tukey tests were applied for individual comparisons between the products in each stage (p≤0.05. Results: Means and standard deviations of roughness and wear (µm after all the promoted stages were: G1=7.26(1.81/13.16(2.67, G2=2.02(0.62/37.44(3.33, G3=1.81(0.91/34.93(6.92, G4=1.92(0.29/38.42(0.65 and G5=1.98(0.53/33.45(2.66. At 60 seconds, all products tended to produce less surface roughness with a variable gradual decrease over time. After polishing, there were no statistically significant differences between the groups, except for G1. Independent of the product utilized, the enamel wear occurred after the micro-abrasion. Conclusions: In this in vitro study, enamel micro-abrasion presented itself as a conservative approach, regardless of the type of the paste compound utilized. These products promoted minor roughness alterations and minimal wear. The use of phosphoric acid and pumice stone showed similar results to commercial products for the micro-abrasion with regard to the surface roughness and wear.

  20. [Comparison of surface roughness of nanofilled and microhybrid composite resins after curing and polishing].

    Science.gov (United States)

    Jiang, Hong; Lv, Da; Liu, Kailei; Zhang, Weisheng; Yao, Yao; Liao, Chuhong

    2014-05-01

    To compare the surface roughness of nanofilled dental composite resin and microhybrid composite resins after curing and polishing. A nanofilled composite (Z350) and 4 microhybrid composites (P60, Z250, Spectrum, and AP-X) were fabricated from the lateral to the medial layers to prepare 8 mm×8 mm×5 mm cubical specimens. The 4 lateral surfaces of each specimens were polished with abrasive disks (Super-Snap). Profilometer was used to test the mean surface roughness (Ra) after polishing. P60 had the lowest Ra (0.125∓0.030 µm) followed by Z250 and Spectrum. The Ra of Z350 (0.205∓0.052 µm) was greater than that of the other 3 resins, and AP-X had the roughest surfaces. Under scanning electron microscope, the polished faces of P60 resin were characterized by minor, evenly distributed particles with fewer scratches; the polished faces of Z350 presented with scratches where defects of the filling material could be seen. The nanofilled composite Z350 has smooth surface after polishing by abrasive disks, but its smoothness remains inferior to that of other micro-hybrid composite resins.

  1. Effects of Delayed Finishing/Polishing on Surface Roughness, Hardness and Gloss of Tooth-Coloured Restorative Materials

    Science.gov (United States)

    Yazici, A. Ruya; Tuncer, Duygu; Antonson, Sibel; Onen, Alev; Kilinc, Evren

    2010-01-01

    Objectives: The aim of this study was to investigate the effect of delayed finishing/polishing on the surface roughness, hardness and gloss of tooth-coloured restorative materials. Methods: Four different tooth-coloured restoratives: a flowable resin composite- Tetric Flow, a hybrid resin composite- Venus, a nanohybrid resin composite- Grandio, and a polyacid modified resin composite- Dyract Extra were used. 30 specimens were made for each material and randomly assigned into three groups. The first group was finished/polished immediately and the second group was finished/polished after 24 hours. The remaining 10 specimens served as control. The surface roughness of each sample was recorded using a laser profilometer. Gloss measurements were performed using a small-area glossmeter. Vickers microhardness measurements were performed from three locations on each specimen surface under 100g load and 10s dwell time. Data for surface roughness and hardness were analyzed by Kruskal Wallis test and data for gloss were subjected to one-way ANOVA and Tukey test (P Grandio samples showed significantly higher roughness than the delayed polished samples (P .05). The lowest hardness values were found under Mylar strip. Delayed finishing/polishing significantly increased the hardness of all materials. Conclusions: The effect of delayed finishing/polishing on surface roughness, gloss and hardness appears to be material dependent. PMID:20046480

  2. FRACTURE BEHAVIOUR OF P/M Cr-V LEDEBURITIC STEEL WITH DIFFERENT SURFACE ROUGHNESS

    Directory of Open Access Journals (Sweden)

    Peter Jurči

    2011-07-01

    Full Text Available The samples made from the Vanadis 6 PM ledeburitic tool steel were surface machined to different quality and heat treated by standard regime of the processing. Three point bending tests were carried out on processed samples. It was found that the flexural strength decreased with decreasing surface quality. The lowering of flexural strength has been accompanied with the decrease of the plastic component of plastic straining preceeding to fracture initiation (work of fracture of the material. It indicates that the surface roughness leads to the crack initiation before a larger plastic deformation of the material can be developed. Based on the results it can be suggested that to prevent the cracking of tools in the practice it is essential to make a surface machining (grinding, lapping, polishing to as high quality as possible.

  3. Soil surface roughness decay in contrasting climates, tillage types and management systems

    Science.gov (United States)

    Vidal Vázquez, Eva; Bertol, Ildegardis; Tondello Barbosa, Fabricio; Paz-Ferreiro, Jorge

    2014-05-01

    Soil surface roughness describes the variations in the elevation of the soil surface. Such variations define the soil surface microrelief, which is characterized by a high spatial variability. Soil surface roughness is a property affecting many processes such as depression storage, infiltration, sediment generation, storage and transport and runoff routing. Therefore the soil surface microrelief is a key element in hydrology and soil erosion processes at different spatial scales as for example at the plot, field or catchment scale. In agricultural land soil surface roughness is mainly created by tillage operations, which promote to different extent the formation of microdepressions and microelevations and increase infiltration and temporal retention of water. The decay of soil surface roughness has been demonstrated to be mainly driven by rain height and rain intensity, and to depend also on runoff, aggregate stability, soil reface porosity and soil surface density. Soil roughness formation and decay may be also influenced by antecedent soil moisture (either before tillage or rain), quantity and type of plant residues over the soil surface and soil composition. Characterization of the rate and intensity of soil surface roughness decay provides valuable information about the degradation of the upper most soil surface layer before soil erosion has been initiated or at the very beginning of soil runoff and erosion processes. We analyzed the rate of decay of soil surface roughness from several experiments conducted in two regions under temperate and subtropical climate and with contrasting land use systems. The data sets studied were obtained both under natural and simulated rainfall for various soil tillage and management types. Soil surface roughness decay was characterized bay several parameters, including classic and single parameters such as the random roughness or the tortuosity and parameters based on advanced geostatistical methods or on the fractal theory. Our

  4. Finite element method analysis of surface roughness transfer in micro flexible rolling

    Directory of Open Access Journals (Sweden)

    Qu Feijun

    2016-01-01

    Full Text Available Micro flexible rolling aims to fabricate submillimeter thick strips with varying thickness profile, where the surface quality of products is mainly determined by initial workpiece surface roughness and subsequent surface asperity flattening process, which is affected by process parameters during rolling. This paper shows a 3D finite element model for flexible rolling of a 250 μm thick workpiece with reduction of 20 to 50%, and rolling phase with thinner thickness indicates a better ability to decrease the surface roughness. Four types of initial workpiece surface roughness are studied in the simulation, and the influences of process parameters, such as friction coefficient, rolling speed and roll gap adjusting speed, on surface asperity flattening of workpieces with different initial surface roughness have been numerically investigated and analysed.

  5. Surface roughness of Ni/Ti multilayers made by magnetron sputtering

    International Nuclear Information System (INIS)

    Pan Lei; Zhu Jingtao; Wang Xiaoqiang; Jiang Li; Li Haochuan; Xu Jing; Zhang Zhong; Wang Zhanshan; Chen Lingyan

    2010-01-01

    Nickel/titanium multilayers with different period of 10, 30, 50 and 75 were fabricated by DC magnetron sputtering. Grazing incidence X-ray measured reflectivity was used to characterize the interfacial roughness of the multilayers. To study the evolution law of surface roughness of Ni/Ti multilayers with different period numbers, atomic force microscope (AFM) was used to characterize the surfaces of the multilayers. The results show that surface roughness of Ni/Ti multilayers increases with the number of periods of the multilayers. As the number of periods increases from 10 to 75, the roughness increases from 0.8 nm to 1.69 nm. Fitting results show that surface roughness mainly varies with the number of periods as a cubic function. (authors)

  6. Track sensitivity and the surface roughness measurements of CR-39 with atomic force microscope

    CERN Document Server

    Yasuda, N; Amemiya, K; Takahashi, H; Kyan, A; Ogura, K

    1999-01-01

    Atomic Force Microscope (AFM) has been applied to evaluate the surface roughness and the track sensitivity of CR-39 track detector. We experimentally confirmed the inverse correlation between the track sensitivity and the roughness of the detector surface after etching. The surface of CR-39 (CR-39 doped with antioxidant (HARZLAS (TD-1)) and copolymer of CR-39/NIPAAm (TNF-1)) with high sensitivity becomes rough by the etching, while the pure CR-39 (BARYOTRAK) with low sensitivity keeps its original surface clarity even for the long etching.

  7. The effect of brushing with nano calcium carbonate and calcium carbonate toothpaste on the surface roughness of nano-ionomer

    Science.gov (United States)

    Anisja, D. H.; Indrani, D. J.; Herda, E.

    2017-08-01

    Nanotechnology developments in dentistry have resulted in the development of nano-ionomer, a new restorative material. The surface roughness of restorative materials can increase bacteria adhesion and lead to poor oral hygiene. Abrasive agents in toothpaste can alter tooth and restorative material surfaces. The aim of this study is to identify the effect of brushing with nano calcium carbonate, and calcium carbonate toothpaste on surface roughness of nano-ionomer. Eighteen nano-ionomer specimens were brushed with Aquabidest (doubledistilled water), nano calcium carbonate and calcium carbonate toothpaste. Brushing lasted 30 minutes, and the roughness value (Ra) was measured after each 10 minute segment using a surface roughness tester. The data was analyzed using repeated ANOVA and one-way ANOVA test. The value of nano-ionomer surface roughness increased significantly (p<0.05) after 20 minutes of brushing with the nano calcium carbonate toothpaste. Brushing with calcium carbonate toothpaste leaves nano-ionomer surfaces more rugged than brushing with nano calcium carbonate toothpaste.

  8. The Effect of Hydrofluoric Acid Etching Duration on the Surface Micromorphology, Roughness, and Wettability of Dental Ceramics

    Directory of Open Access Journals (Sweden)

    Ravikumar Ramakrishnaiah

    2016-05-01

    Full Text Available The current laboratory study is evaluating the effect of hydrofluoric acid etching duration on the surface characteristics of five silica-based glass ceramics. Changes in the pore pattern, crystal structure, roughness, and wettability were compared and evaluated. Seventy-five rectangularly shaped specimens were cut from each material (IPS e-max™, Dentsply Celtra™, Vita Suprinity™, Vita mark II™, and Vita Suprinity FC™; the sectioned samples were finished, polished, and ultrasonically cleaned. Specimens were randomly assigned into study groups: control (no etching and four experimental groups (20, 40, 80 and 160 s of etching. The etched surfaces’ microstructure including crystal structure, pore pattern, pore depth, and pore width was studied under a scanning electron microscope, and the surface roughness and wettability were analyzed using a non-contact surface profilometer and a contact angle measuring device, respectively. The results were statistically analyzed using one-way analysis of variance (ANOVA and the post hoc Tukey’s test. The results showed a significant change in the pore number, pore pattern, crystal structure, surface roughness, and wettability with increased etching duration. Etching for a short time resulted in small pores, and etching for longer times resulted in wider, irregular grooves. A significant increase in the surface roughness and wettability was observed with an increase in the etching duration. The findings also suggested a strong association between the surface roughness and wettability.

  9. A general rough-surface inversion algorithm: Theory and application to SAR data

    Science.gov (United States)

    Moghaddam, M.

    1993-01-01

    Rough-surface inversion has significant applications in interpretation of SAR data obtained over bare soil surfaces and agricultural lands. Due to the sparsity of data and the large pixel size in SAR applications, it is not feasible to carry out inversions based on numerical scattering models. The alternative is to use parameter estimation techniques based on approximate analytical or empirical models. Hence, there are two issues to be addressed, namely, what model to choose and what estimation algorithm to apply. Here, a small perturbation model (SPM) is used to express the backscattering coefficients of the rough surface in terms of three surface parameters. The algorithm used to estimate these parameters is based on a nonlinear least-squares criterion. The least-squares optimization methods are widely used in estimation theory, but the distinguishing factor for SAR applications is incorporating the stochastic nature of both the unknown parameters and the data into formulation, which will be discussed in detail. The algorithm is tested with synthetic data, and several Newton-type least-squares minimization methods are discussed to compare their convergence characteristics. Finally, the algorithm is applied to multifrequency polarimetric SAR data obtained over some bare soil and agricultural fields. Results will be shown and compared to ground-truth measurements obtained from these areas. The strength of this general approach to inversion of SAR data is that it can be easily modified for use with any scattering model without changing any of the inversion steps. Note also that, for the same reason it is not limited to inversion of rough surfaces, and can be applied to any parameterized scattering process.

  10. Influence of ion beam bombardment on surface roughness of K9 glass substrate

    Science.gov (United States)

    Pan, Yongqiang; Huang, Guojun; Hang, Lingxia

    2010-10-01

    Ion beam bombardment optical substrate surface has become an important part of process of optical thin films deposition. In this work, the K9 optical glass is bombarded by the broad beam cold cathode ion source. The dependence of the K9 glass surface roughness on the ion beam bombardment time, the ion energy, the distance and incident angle are all investigated, respectively. Surface roughness of K9 glass is measured using Talysurf CCI. The experimental results show that when the ion energy is 800ev, the bombardment distance of 20cm, with the ion beam bombardment time increased, the K9 substrate surface roughness first increase and then decrease. When the ion beam bombardment distance is 20cm, bombardment time is 10min, with the bombardment energy increases, substrate surface roughness increase first and then decrease, especially in the ion energy greater than 1200ev, the optical substrate surface roughness rapidly increases. When the ion energy is 800 eV, bombardment time is 10min, with the bombardment distance increase, substrate surface roughness decrease gradually. Furthermore, the incident angle of ion beam plays an important role in improving the K9 glass surface roughness.

  11. Optimization of Surface Roughness and Wall Thickness in Dieless Incremental Forming Of Aluminum Sheet Using Taguchi

    Science.gov (United States)

    Hamedon, Zamzuri; Kuang, Shea Cheng; Jaafar, Hasnulhadi; Azhari, Azmir

    2018-03-01

    Incremental sheet forming is a versatile sheet metal forming process where a sheet metal is formed into its final shape by a series of localized deformation without a specialised die. However, it still has many shortcomings that need to be overcome such as geometric accuracy, surface roughness, formability, forming speed, and so on. This project focus on minimising the surface roughness of aluminium sheet and improving its thickness uniformity in incremental sheet forming via optimisation of wall angle, feed rate, and step size. Besides, the effect of wall angle, feed rate, and step size to the surface roughness and thickness uniformity of aluminium sheet was investigated in this project. From the results, it was observed that surface roughness and thickness uniformity were inversely varied due to the formation of surface waviness. Increase in feed rate and decrease in step size will produce a lower surface roughness, while uniform thickness reduction was obtained by reducing the wall angle and step size. By using Taguchi analysis, the optimum parameters for minimum surface roughness and uniform thickness reduction of aluminium sheet were determined. The finding of this project helps to reduce the time in optimising the surface roughness and thickness uniformity in incremental sheet forming.

  12. The interplay between surface charging and microscale roughness during plasma etching of polymeric substrates

    Science.gov (United States)

    Memos, George; Lidorikis, Elefterios; Kokkoris, George

    2018-02-01

    The surface roughness developed during plasma etching of polymeric substrates is critical for a variety of applications related to the wetting behavior and the interaction of surfaces with cells. Toward the understanding and, ultimately, the manipulation of plasma induced surface roughness, the interplay between surface charging and microscale roughness of polymeric substrates is investigated by a modeling framework consisting of a surface charging module, a surface etching model, and a profile evolution module. The evolution of initially rough profiles during plasma etching is calculated by taking into account as well as by neglecting charging. It is revealed, on the one hand, that the surface charging contributes to the suppression of root mean square roughness and, on the other hand, that the decrease of the surface roughness induces a decrease of the charging potential. The effect of charging on roughness is intense when the etching yield depends solely on the ion energy, and it is mitigated when the etching yield additionally depends on the angle of ion incidence. The charging time, i.e., the time required for reaching a steady state charging potential, is found to depend on the thickness of the polymeric substrate, and it is calculated in the order of milliseconds.

  13. Surface roughness of rock faces through the curvature of triangulated meshes

    Science.gov (United States)

    Lai, P.; Samson, C.; Bose, P.

    2014-09-01

    In this paper, we examine three different measures of roughness based on a geometric property of surfaces known as curvature. These methods were demonstrated using an image of a large rock face made up of a smooth blocky limestone in contact with a rough friable dolostone. The point cloud analysed contained 10,334,288 points and was acquired at a distance of 3 m from the rock face. The point cloud was first decimated using an epsilon-net and then meshed using the Poisson surface reconstruction method before the proposed measures of roughness were applied. The first measure of roughness is defined as the difference in curvature between a mesh and a smoothed version of the same mesh. The second measure of roughness is a voting system applied to each vertex which identifies the subset of vertices which represent rough regions within the mesh. The third measure of roughness uses a combination of spatial partitioning data structures and data clustering in order to define roughness for a region in the mesh. The spatial partitioning data structure allows for a hierarchy of roughness values which is related to the size of the region being considered. All of the proposed measures of roughness are visualised using colour-coded displays which allows for an intuitive interpretation.

  14. Friction and adhesion of gecko-inspired PDMS flaps on rough surfaces.

    Science.gov (United States)

    Yu, Jing; Chary, Sathya; Das, Saurabh; Tamelier, John; Turner, Kimberly L; Israelachvili, Jacob N

    2012-08-07

    Geckos have developed a unique hierarchical structure to maintain climbing ability on surfaces with different roughness, one of the extremely important parameters that affect the friction and adhesion forces between two surfaces. Although much attention has been paid on fabricating various structures that mimic the hierarchical structure of a gecko foot, yet no systematic effort, in experiment or theory, has been made to quantify the effect of surface roughness on the performance of the fabricated structures that mimic the hierarchical structure of geckos. Using a modified surface forces apparatus (SFA), we measured the adhesion and friction forces between microfabricated tilted PDMS flaps and optically smooth SiO(2) and rough SiO(2) surfaces created by plasma etching. Anisotropic adhesion and friction forces were measured when sliding the top glass surface along (+y) and against (-y) the tilted direction of the flaps. Increasing the surface roughness first increased the adhesion and friction forces measured between the flaps and the rough surface due to topological matching of the two surfaces but then led to a rapid decrease in both of these forces. Our results demonstrate that the surface roughness significantly affects the performance of gecko mimetic adhesives and that different surface textures can either increase or decrease the adhesion and friction forces of the fabricated adhesives.

  15. Dynamical structure of the turbulent boundary layer on rough surface

    Czech Academy of Sciences Publication Activity Database

    Uruba, Václav; Jonáš, Pavel; Hladík, Ondřej

    2011-01-01

    Roč. 11, č. 1 (2011), s. 603-604 ISSN 1617-7061 R&D Projects: GA ČR GA101/08/1112; GA ČR GAP101/10/1230 Institutional research plan: CEZ:AV0Z20760514 Keywords : turbulent boundary layer * rough wall * hairpin vortex Subject RIV: BK - Fluid Dynamics http://onlinelibrary.wiley.com/doi/10.1002/pamm.201110291/abstract

  16. Optical Roughness Measuring Instrument For Fine-Machined Surfaces

    Science.gov (United States)

    Brodmann, Rainer; Gerstorfer, Oskar; Thurn, Gerd

    1985-06-01

    The roughness measuring instrument described is based on light scattering and is suitable in a wide range of applications, especially in micro-machining. The most important properties are the sensitivity in the measuring range from below 0.005 i.im up to 2µm (Ra value), the independence of the reflection coefficient due to normalization, and the larger tolerance of measur-ing distance of +/-2 mm.

  17. Influence of graphite particles on surface roughness and chip formation studies in turning metal matrix composites

    Directory of Open Access Journals (Sweden)

    S. Basavarajappa

    2013-01-01

    Full Text Available This study presents an experimental investigation on surface roughness and chip formation in turning of Al 2219/15SiCp and Al 2219/15SiCp-3Gr (hybrid composites. Experiments were conducted with different cutting conditions using carbide, coated carbide and polycrystalline diamond (PCD tools. The results reveal that the surface roughness values are less for coated carbide tools compared to carbide and are minimum for PCD tools. The incorporation of graphite in Al 2219/15SiCp composite increases the surface roughness. This is due to smearing and removal of softer and amorphus graphite particles on the surface of the specimen, creates pits on the machined surface which increases the surface roughness values. The graphitic composite produced discontinuous chips leads to easy machining. PCD tool performs better than carbide and coated carbide tools.

  18. Degradation of unglazed rough graphite-aluminium solar absorber surfaces in simulated acid and neutral rain

    International Nuclear Information System (INIS)

    Konttinen, P.; Lund, P.D.; Salo, T.

    2005-01-01

    Degradation mechanisms of unglazed solar absorber surfaces based on aluminium substrate were studied. Rough graphite-aluminium surfaces were total-immersion subjected to aerated and de-aerated simulated neutral and acid rain. Test conditions were based on calculated absorber stagnation temperature and global rain acidity measurements. Changes in optical properties, elemental composition and sample mass were examined by spectrometry, energy dispersive X-ray spectrometry and thermogravimetry, respectively. The absorbers exhibited almost no degradation at pH value of 3.5. At pH 5.5 alumina on the surface hydrated significantly degrading the optical properties of the surfaces severely in most cases. Therefore these absorber surfaces can not be recommended to be used in non-glazed applications if they are exposed to rain with pH exceeding ∼ 3.5-4.5. The total-immersion test needs to be developed further as the test results exhibited poor temperature and time dependency thus preventing accurate service lifetime estimates. Still, these tests were useful in determining favourable and non-favourable operating conditions for the absorber surfaces based on aluminium substrate. (author)

  19. Study on the influence of helical milling parameters on surface roughness of titanium alloy

    Directory of Open Access Journals (Sweden)

    Chunhui JI

    2015-06-01

    Full Text Available As a new technology, helical milling has been widely used in hole-making of titanium alloy, and the surface roughness is an important indicator for evaluating the quality of titanium alloy hole. In this paper, the helical milling experiments are carried out to study the effect of machining parameters on the surface roughness with the model established in Matlab. It is proved that the model can well predict the influence of the helical milling parameters on surface roughness. With screw pitch increasing, the surface roughness of titanium hole firstly decreases and then increases in the range of 0.15~0.25 mm/rev. However, the surface roughness increases gradually at first and then decreases with the increasing of the feed per tooth in the range of 0.03~0.05 mm/tooth. Similarly, with the increasing of spindle speed, the surface roughness firstly increases, then decreases, and again gradually increases smoothly in the range of 2 500~3 500 r/min. The results in the work can provide experimental basis for optimizing cutting parameters and decreasing surface roughness in helical milling process.

  20. The effect of surface roughness on the turbulence structure of a plane wall jet

    Science.gov (United States)

    Rostamy, N.; Bergstrom, D. J.; Sumner, D.; Bugg, J. D.

    2011-08-01

    In this paper, an experimental investigation of the turbulence characteristics of a plane wall jet over smooth and rough surfaces, using laser Doppler anemometry (LDA), is reported. The Reynolds number based on the slot height and exit velocity of the jet was approximately Re = 7500. A 36-grit sheet was used as the rough surface, creating a transitionally rough flow regime (44surface roughness on the Reynolds stress profiles. Comparisons between the present results and other LDA and hot-wire anemometry studies for a smooth surface indicate a similar behavior for the Reynolds stress profiles. However, the magnitudes of the peak values of the Reynolds stress were higher than in most previous studies due to the lower slot Reynolds number. The present results indicate that surface roughness does not appear to significantly modify the Reynolds stress profiles in the outer region of the jet except for a reduction in the level. In contrast, surface roughness modifies both the shape and magnitudes of the Reynolds stress profiles in the inner layer. Due to the much higher friction velocity for a rough surface, the magnitudes of both the streamwise and wall-normal Reynolds stress decrease in the inner region when normalized using inner scales compared to the smooth-wall values.

  1. Surface roughness characterization of Al-doped zinc oxide thin films using rapid optical measurement

    Science.gov (United States)

    Kuo, Chil-Chyuan

    2011-07-01

    Transparent conductive oxide thin films have been widely investigated in photoelectric devices such as flat panel display (FPD) and solar cells. Al-doped zinc oxide (AZO) thin films have been widely employed in FPD. Measuring the surface roughness of AZO thin films is important before the manufacturing of photoelectric device using AZO thin films because surface roughness of AZO thin films will significantly affect the performance of photoelectric device. Traditional methods to measure surface roughness of AZO thin films are scanning electron microscopy and atomic force microscopy. The disadvantages of these approaches include long lead time and slow measurement speed. To solve this problem, an optical inspection system for rapid measurement of the surface roughness of AZO thin films is developed in this study. It is found that the incident angle of 60° is a good candidate to measure the surface roughness of AZO thin films. Based on the trend equation y=-3.6483 x+2.1409, the surface roughness of AZO thin films ( y) can be directly deduced from the peak power density ( x) using the optical inspection system developed. The maximum measurement-error rate of the optical inspection system developed is less than 8.7%.The saving in inspection time of the surface roughness of AZO thin films is up to 83%.

  2. Effect of implantoplasty on fracture resistance and surface roughness of standard diameter dental implants.

    Science.gov (United States)

    Costa-Berenguer, Xavier; García-García, Marta; Sánchez-Torres, Alba; Sanz-Alonso, Mariano; Figueiredo, Rui; Valmaseda-Castellón, Eduard

    2018-01-01

    To assess the effect of implantoplasty on the fracture resistance, surface roughness, and macroscopic morphology of standard diameter (4.1 mm) external connection dental implants. An in vitro study was conducted in 20 screw-shaped titanium dental implants with an external connection. In 10 implants, the threads and surface were removed and polished with high-speed burs (implantoplasty), while the remaining 10 implants were used as controls. The final implant dimensions were recorded. The newly polished surface quality was assessed by scanning electron microscopy (SEM) and by 3D surface roughness analysis using a confocal laser microscope. Finally, all the implants were subjected to a mechanical pressure resistance test. A descriptive analysis of the data was made. Also, Student's t tests were employed to detect differences regarding the compression tests. Implantoplasty was carried out for a mean time of 10 min and 48 s (standard deviation (SD) of 1 min 22 s). Macroscopically, the resulting surface had a smooth appearance, although small titanium shavings and silicon debris were present. The final surface roughness (S a values 0.1 ± 0.02 μm) was significantly lower than that of the original (0.75 ± 0.08 μm S a ) (p = .005). There was minimal reduction in the implant's inner body diameter (0.19 ± 0.03 mm), and no statistically significant differences were found between the test and control implants regarding the maximum resistance force (896 vs 880 N, respectively). Implantoplasty, although technically demanding and time-consuming, does not seem to significantly alter fracture resistance of standard diameter external connection implants. A smooth surface with S a values below 0.1 μm can be obtained through the use of silicon polishers. A larger sample is required to confirm that implantoplasty does not significantly affect the maximum resistance force of standard diameter external connection implants. © 2017 John Wiley & Sons A/S. Published

  3. Characterizing the Surface Roughness Length Scales of Lactose Carrier Particles in Dry Powder Inhalers.

    Science.gov (United States)

    Tan, Bernice Mei Jin; Chan, Lai Wah; Heng, Paul Wan Sia

    2018-03-06

    Surface roughness is well recognized as a critical physical property of particulate systems, particularly in relation to adhesion, friction, and flow. An example is the surface property of carrier particles in carrier-based dry powder inhaler (DPI) formulations. The numerical characterization of roughness remains rather unsatisfactory due to the lack of spatial (or length scale) information about surface features when a common amplitude parameter such as average roughness ( R a ) is used. An analysis of the roughness of lactose carrier particles at three different length scales, designed for specificity to the study of interactive mixtures in DPI, was explored in this study. Three R a parameters were used to represent the microscale, intermediate scale, and macroscale roughness of six types of surface-modified carriers. Coating of micronized lactose fines on coarse carrier particles increased their microroughness from 389 to 639 nm while the macroroughness was not affected. Roller compaction at higher roll forces led to very effective surface roughening, particularly at longer length scales. Changes in R a parameters corroborated the visual observations of particles under the scanning electron microscope. Roughness at the intermediate scale showed the best correlation with the fine particle fraction (FPF) of DPI formulations. From the range of 250 to 650 nm, every 100 nm increase in the intermediate roughness led to ∼8% increase in the FPF. However, the effect of surface roughness was greatly diminished when fine lactose (median size, 9 μm) of comparable amounts to the micronized drug were added to the formulation. The combination of roughness parameters at various length scales provided much discriminatory surface information, which then revealed the "quality" of roughness necessary for improving DPI performance.

  4. Caries management by risk assessment (CAMBRA) and its effect on the surface roughness of various restorative materials.

    Science.gov (United States)

    Bolding, Lauren M; Masri, Radi; Arola, Dwayne; Driscoll, Carl F; Romberg, Elaine

    2015-10-01

    Whether topical anticaries medicaments used in the oral environment will affect the surface integrity of restorative materials is uncertain. The purpose of this in vitro study was to investigate the effect of various anticaries agents on the surface roughness of 3 different restorative materials. Sixty-four specimens of each restorative material (feldspathic porcelain, Ni-Cr metal ceramic alloy, and Ti-6Al-4V titanium alloy) were prepared and separated into 4 equal groups for soaking in anticaries agents (Prevident Dental Rinse, ACT mouth wash, chlorhexidine gluconate, and water). A profilometer was used to measure surface roughness before and after soaking the materials for 2 years of simulated usage. The mean change in surface roughness for each specimen was calculated. Statistical analysis was performed with a 2-way ANOVA, followed by the Tukey HSD test (α=.05). A significant interaction was found between the materials and anticaries agents (F=2.64, P=.02). The significant interaction was between Prevident and chlorhexidine gluconate. Porcelain specimens soaked in Prevident produced a negative change (-0.072 ±0.35 μm) in surface roughness (smoother surface), while chlorhexidine gluconate produced a positive change (0.094 ±0.42 μm) in surface roughness (rougher surface). Within the limitations of this in vitro study, it can be concluded that Prevident Dental Rinse and chlorhexidine gluconate may cause a change in the surface roughness of feldspathic porcelain. Copyright © 2015 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

  5. The effect of scattered light sensor orientation on roughness measurement of curved polished surfaces

    DEFF Research Database (Denmark)

    Pilny, Lukas; Bissacco, Giuliano; De Chiffre, Leonardo

    2014-01-01

    Light scattering is a method for surface roughness measurements well suitable for use in a production environment thanks to its fast measurement rate, insensitivity to vibrations and to small misalignments. The method is however affected by several other factors. In this paper, the effect of angu...... of angular orientation of a commercial scattered light sensor on roughness measurements of polished cylindrical surfaces with crossed surface lay is investigated to document the robustness of the method....

  6. Efficient Monte Carlo Simulation of Scattering from Rough Sea Surfaces with Objects via Transformation Electromagne

    OpenAIRE

    Özgün, Özlem

    2013-01-01

    Statistical properties of scattered fields (or radar cross section values) in electromagnetic scattering from objects (such as ship- and decoy-like objects) on or above random rough sea surfaces are predicted by using transformation electromagnetics, finite element method (FEM) and Monte Carlo technique. The rough sea surface is modeled as a random process and is randomly generated by using the Pierson-Moskowitz spectrum. For each realization of the sea surface, scattered fields and the radar...

  7. Multi-scale Analysis of Topographic Surface Roughness in the Midland Valley, Scotland

    OpenAIRE

    Grohmann, Carlos

    2017-01-01

    Surface roughness is an important geomorphological variable which has been used in the earth and planetary sciences to infer material properties, current/past processes and the time elapsed since formation. No single definition exists, however within the context of geomorphometry we use surface roughness as a expression of the variability of a topographic surface at a given scale, where the scale of analysis is determined by the size of the landforms or geomorphic features of interest. Six te...

  8. Surface properties of Ti-6Al-4V alloy part I: Surface roughness and apparent surface free energy.

    Science.gov (United States)

    Yan, Yingdi; Chibowski, Emil; Szcześ, Aleksandra

    2017-01-01

    Titanium (Ti) and its alloys are the most often used implants material in dental treatment and orthopedics. Topography and wettability of its surface play important role in film formation, protein adhesion, following osseointegration and even duration of inserted implant. In this paper, we prepared Ti-6Al-4V alloy samples using different smoothing and polishing materials as well the air plasma treatment, on which contact angles of water, formamide and diiodomethane were measured. Then the apparent surface free energy was calculated using four different approaches (CAH, LWAB, O-W and Neumann's Equation of State). From LWAB approach the components of surface free energy were obtained, which shed more light on the wetting properties of samples surface. The surface roughness of the prepared samples was investigated with the help of optical profilometer and AFM. It was interesting whether the surface roughness affects the apparent surface free energy. It was found that both polar interactions the electron donor parameter of the energy and the work of water adhesion increased with decreasing roughness of the surfaces. Moreover, short time plasma treatment (1min) caused decrease in the surface hydrophilic character, while longer time (10min) treatment caused significant increase in the polar interactions and the work of water adhesion. Although Ti-6Al-4V alloy has been investigated many times, to our knowledge, so far no paper has been published in which surface roughness and changes in the surface free energy of the alloy were compared in the quantitative way in such large extent. This novel approach deliver better knowledge about the surface properties of differently smoothed and polished samples which may be helpful to facilitate cell adhesion, proliferation and mineralization. Therefore the results obtained present also potentially practical meaning. Copyright © 2016 Elsevier B.V. All rights reserved.

  9. The Effect of Finishing and Polishing Techniques on the Surface Roughness and the Color of Nanocomposite Resin Restorative Materials.

    Science.gov (United States)

    Avsar, Aysun; Yuzbasioglu, Emir; Sarac, Duygu

    2015-01-01

    Rough, poorly polished surfaces contribute to staining, plaque accumulation, gingival irritation and recurrent caries. Finishing and polishing techniques are critical factors contributing to the longevity of the direct composite resin restorations. The aim of this in vitro study was to evaluate the effects of finishing and polishing systems on surface roughness of six nanocomposite restorative resins. Thirty specimens of each restorative material (n=180) were placed in a teflon mould (6 mm in diameter and 3 mm in depth) and cured with a LED curing unit. Six specimens from each of restorative material were randomly assigned to four groups for finishing and polishing (carbide burs, diamond burs, aluminium oxide discs, silicon rubber polisher) techniques. Mylar strip formed specimens were served as control group. After finishing and polishing procedures surface roughness was evaluated by a profilometer. The data was analyzed by 2-way analysis of variance and the Tukey HSD test (α=0.05). Significant differences were found between the groups in terms roughness (prestorative materials. Although mylar matrix strip formed surfaces presents lower surface roughness values, recountouring and polishing of resin restorations are often required in clinical situations. Aluminium oxide discs and carbide finishing burs are suitable for finishing and polishing procedures for nanocomposite restorative resins.

  10. Heat Transfer Enhancement By Three-Dimensional Surface Roughness Technique In Nuclear Fuel Rod Bundles

    Science.gov (United States)

    Najeeb, Umair

    This thesis experimentally investigates the enhancement of single-phase heat transfer, frictional loss and pressure drop characteristics in a Single Heater Element Loop Tester (SHELT). The heater element simulates a single fuel rod for Pressurized Nuclear reactor. In this experimental investigation, the effect of the outer surface roughness of a simulated nuclear rod bundle was studied. The outer surface of a simulated fuel rod was created with a three-dimensional (Diamond-shaped blocks) surface roughness. The angle of corrugation for each diamond was 45 degrees. The length of each side of a diamond block is 1 mm. The depth of each diamond block was 0.3 mm. The pitch of the pattern was 1.614 mm. The simulated fuel rod had an outside diameter of 9.5 mm and wall thickness of 1.5 mm and was placed in a test-section made of 38.1 mm inner diameter, wall thickness 6.35 mm aluminum pipe. The Simulated fuel rod was made of Nickel 200 and Inconel 625 materials. The fuel rod was connected to 10 KW DC power supply. The Inconel 625 material of the rod with an electrical resistance of 32.3 kO was used to generate heat inside the test-section. The heat energy dissipated from the Inconel tube due to the flow of electrical current flows into the working fluid across the rod at constant heat flux conditions. The DI water was employed as working fluid for this experimental investigation. The temperature and pressure readings for both smooth and rough regions of the fuel rod were recorded and compared later to find enhancement in heat transfer coefficient and increment in the pressure drops. Tests were conducted for Reynold's Numbers ranging from 10e4 to 10e5. Enhancement in heat transfer coefficient at all Re was recorded. The maximum heat transfer co-efficient enhancement recorded was 86% at Re = 4.18e5. It was also observed that the pressure drop and friction factor increased by 14.7% due to the increased surface roughness.

  11. Effects of thermal cycling on surface roughness, hardness and flexural strength of polymethylmethacrylate and polyamide denture base resins.

    Science.gov (United States)

    Ayaz, Elif Aydoğan; Bağış, Bora; Turgut, Sedanur

    2015-10-16

    The purpose of this study was to evaluate the effects of thermal cycling on the surface roughness, hardness and flexural strength of denture resins. Polyamide (PA; Deflex and Valplast) and polymethylmethacrylate (PMMA; QC-20 and Acron MC) denture materials were selected. A total of 180 specimens were fabricated and then divided into 3 groups. The first group (group 1) acted as a control and was not thermocycled. The second group (group 2) was subjected to thermocycling for 10,000 cycles in artificial saliva and 5,000 cycles in distilled water. The last group (group 3) was thermocycled for 20,000 cycles in artificial saliva and 10,000 cycles in distilled water. The surface roughness were measured with a profilometer. The hardness of the resins were measured with a Vickers Hardness Tester using a 100-gf load. The flexural strength test was performed using the universal test machine with a crosshead speed of 5 mm/min. Data were analyzed using statistical software. The results of the measurements in the 3 different tests were analyzed by Kruskal-Wallis test with Bonferroni correction. Multiple comparisons were made by Conover and Wilcoxon tests. There was a significant difference between the PMMA and PA groups in terms of surface roughness, hardness and transverse strength before and after thermal cycling (p<0.001). Thermal cycling did not change the surface roughness, hardness and flexural strength values of either the PMMA or PA group (p>0.001).

  12. Surface Roughness Attenuation in EHL Line and Point Contacts under Conditions of Starved Lubrication

    NARCIS (Netherlands)

    Venner, C.H.; Hooke, C.J.; Snidle, R.W.; Evans, H.P.

    2006-01-01

    The authors have previously examined the effect of surface roughness in line and point EHL contacts and have shown that it is the ratio of the wavelength to the inlet pressure sweep that determines the degree of roughness attenuation under the contact. Because of this a single curve can be used to

  13. Surface roughness and grain boundary scattering effects on the electrical conductivity of thin films

    NARCIS (Netherlands)

    Palasantzas, George

    1998-01-01

    In this work, we investigate surface/interface roughness and grain boundary scattering effects on the electrical conductivity of polycrystalline thin films in the Born approximation. We assume for simplicity a random Gaussian roughness convoluted with a domain size distribution ~e^-πr^2/ζ^2 to

  14. Study on the Light Scattering from Random Rough Surfaces by Kirrhoff Approximation

    Directory of Open Access Journals (Sweden)

    Keding Yan

    2014-07-01

    Full Text Available In order to study the space distribution characteristics of light scattering from random rough surfaces, the linear filtering method is used to generate a series of Gaussian randomly rough surfaces, and the Kirchhoff Approximation is used to calculate the scattered light intensity distribution from random metal and dielectric rough surfaces. The three characteristics of the scattered light intensity distribution peak, the intensity distribution width and the position of peak are reviewed. Numerical calculation results show that significant differences between scattering characteristics of metal surfaces and the dielectric surfaces exist. The light scattering characteristics are jointly influenced by the slope distribution and reflectance of surface element. The scattered light intensity distribution is affected by common influence of surface local slope distribution and surface local reflectivity. The results can provide a basis theory for the research to lidar target surface scattering characteristics.

  15. Original Research. Surface Roughness Changes of Different Restoration Materials after Tooth Brushing Simulation Using Different Toothpastes

    Directory of Open Access Journals (Sweden)

    Dudás Csaba

    2017-03-01

    Full Text Available Background: The need for the whitening effects of toothpastes became primary for most users. Changes in the surface roughness of restoration materials after tooth brushing are inevitable, and the abrasion is known to increase the possibility of dental plaque accumulation. Aim of the study: To evaluate in vitro surface roughness changes of different dental restorative materials after tooth brushing simulation. Material and methods: Fifty specimens of two composite materials (Evicrol, Super-Cor, two glass ionomer materials (Glassfill, Kavitan Cem and a silicate cement (Fritex were prepared according to the manufacturer’s instructions. Each group of specimens was divided in three subgroups for tooth brushing simulation: using two different types of toothpaste and without toothpaste. Before and after 153 hours of tooth brushing simulation with a custom-made device, the surface roughness was measured with a surface roughness tester. Statistical analysis was performed after collecting the data. Results: All materials exhibited changes in surface roughness after the use of both toothpastes. The self-curing composite showed the less change and glass ionomer materials showed the greatest changes in surface roughness. Conclusions: The surface changes of dental materials depended on their composition and the cleaning procedure. Although self-curing composite was the most resistant to surface changes, its surface roughness values were high. Light-curing composite presented the lowest surface roughness values, even after brushing with toothpastes. The “medium” labeled toothbrush caused significant changes without toothpaste on the surface of light-curing composite, glass ionomer and silicate cement materials.

  16. Evaluate the Effect of Commercially Available Denture Cleansers on Surface Hardness and Roughness of Denture Liners at Various Time Intervals

    Science.gov (United States)

    Mohammed, Hilal S.; Singh, Sumeet; Hari, Prasad A.; Amarnath, G. S.; Kundapur, Vinaya; Pasha, Naveed; Anand, M.

    2016-01-01

    Background and objective: Chemical cleansing by denture cleansers is first choice for denture plaque control. The most common problems while using denture cleansers are hardening, porosity, odor sorption, water sorption, solubility, and colour change, bacterial and fungal growth. Chemical cleansing procedures have been found to have an effect on the physical and mechanical properties of denture liners. Thus, this study was conducted to evaluate the effect of commercially available denture cleansers on surface hardness and roughness of acrylic and silicon based denture liners at various time interval. Method: Two autopolymerising denture liners Kooliner (acrylic) and GC reline soft (silicon) were tested with two commercially available denture cleansers, polident and efferdent plus. Total of 120 specimens were prepared and all the specimens were divided into six groups based on the relining materials and denture cleansers used. Surface hardness and surface roughness was tested using Shore A durometer and profilometer respectively at the end of day 1, day 7, day 30 and day 90. All the specimens were stored in artificial saliva throughout the study. Cleanser solution was prepared daily by adding Polident and Efferdent plus denture cleanser tablet into 250ml of enough very warm (not hot) water. Acrylic and silicon liner groups were cleansed in a solution of denture cleanser and water for 15 minutes daily, rinsed with water and stored in artificial saliva at room temperature. The data was analyzed with one way ANOVA and independent t-test. Result: The acrylic soft lining showed gradual hardening and increase in surface roughness after immersion in denture cleanser and also with time. Acrylic liner material showed maximum hardness and roughness with Polident followed by Efferdent plus and water (control group). Silicone lining material showed a slight difference in hardness and roughness between the test group and control group. There was a slight increase in hardness in

  17. Grasping Claws of Bionic Climbing Robot for Rough Wall Surface: Modeling and Analysis

    Directory of Open Access Journals (Sweden)

    Quansheng Jiang

    2017-12-01

    Full Text Available Aiming at the inspection of rough stone and concrete wall surfaces, a grasping module of cross-arranged claw is designed. It can attach onto rough wall surfaces by hooking or grasping walls. First, based on the interaction mechanism of hooks and rough wall surfaces, the hook structures in claw tips are developed. Then, the size of the hook tip is calculated and the failure mode is analyzed. The effectiveness and reliability of the mechanism are verified through simulation and finite element analysis. Afterwards, the prototype of the grasping module of claw is established to carry out grasping experiment on vibrating walls. Finally, the experimental results demonstrate that the proposed cross-arranged claw is able to stably grasp static wall surfaces and perform well in grasping vibrating walls, with certain anti-rollover capability. This research lays a foundation for future researches on wall climbing robots with vibrating rough wall surfaces.

  18. Analysis of WEDM Process Parameters on Surface Roughness and Kerf using Taguchi Method

    Directory of Open Access Journals (Sweden)

    Asfana Banu

    2017-12-01

    Full Text Available In obtaining the best quality of engineering parts, the quality of machined surface plays an essential role. The fatigue strength, wear resistance, and corrosion of workpiece are some of the aspects of the qualities that can be improved. This paper investigates the effect of wire electrical discharge machining (WEDM process parameters on surface roughness and kerf on stainless steel using distilled water as dielectric fluid and brass wire as tool electrode. The selected process parameters are voltage open, wire speed, wire tension, voltage gap, and off time. Empirical models using Taguchi method were developed for the estimation of surface roughness and kerf. The analysis revealed that off time has major influence on surface roughness and kerf. The optimum machining parameters for minimum surface roughness and kerf were found to be 10 V open voltage, 2.84 µs off time, 12 m/min wire speed, 6.3 N wire tension, and 54.91 V voltage gap.

  19. Influence of Wire Electrical Discharge Machining (WEDM) process parameters on surface roughness

    Science.gov (United States)

    Yeakub Ali, Mohammad; Banu, Asfana; Abu Bakar, Mazilah

    2018-01-01

    In obtaining the best quality of engineering components, the quality of machined parts surface plays an important role. It improves the fatigue strength, wear resistance, and corrosion of workpiece. This paper investigates the effects of wire electrical discharge machining (WEDM) process parameters on surface roughness of stainless steel using distilled water as dielectric fluid and brass wire as tool electrode. The parameters selected are voltage open, wire speed, wire tension, voltage gap, and off time. Empirical model was developed for the estimation of surface roughness. The analysis revealed that off time has a major influence on surface roughness. The optimum machining parameters for minimum surface roughness were found to be at a 10 V open voltage, 2.84 μs off time, 12 m/min wire speed, 6.3 N wire tension, and 54.91 V voltage gap.

  20. Effects of Surface Roughness, Oxidation, and Temperature on the Emissivity of Reactor Pressure Vessel Alloys

    Energy Technology Data Exchange (ETDEWEB)

    King, J. L. [University of Wisconsin–Madison, Department of Engineering Physics, Madison, Wisconsin; Jo, H. [University of Wisconsin–Madison, Department of Engineering Physics, Madison, Wisconsin; Tirawat, R. [National Renewable Energy Laboratory, Concentrating Solar Power Group, Golden, Colorado; Blomstrand, K. [University of Wisconsin–Madison, Department of Engineering Physics, Madison, Wisconsin; Sridharan, K. [University of Wisconsin–Madison, Department of Engineering Physics, Madison, Wisconsin

    2017-08-31

    Thermal radiation will be an important mode of heat transfer in future high-temperature reactors and in off-normal high-temperature scenarios in present reactors. In this work, spectral directional emissivities of two reactor pressure vessel (RPV) candidate materials were measured at room temperature after exposure to high-temperature air. In the case of SA508 steel, significant increases in emissivity were observed due to oxidation. In the case of Grade 91 steel, only very small increases were observed under the tested conditions. Effects of roughness were also investigated. To study the effects of roughening, unexposed samples of SA508 and Grade 91 steel were roughened via one of either grinding or shot-peening before being measured. Significant increases were observed only in samples having roughness exceeding the roughness expected of RPV surfaces. While the emissivity increases for SA508 from oxidation were indeed significant, the measured emissivity coefficients were below that of values commonly used in heat transfer models. Based on the observed experimental data, recommendations for emissivity inputs for heat transfer simulations are provided.

  1. Cement-base bearing pads mortar for connections in the precast concrete: study of surface roughness

    Directory of Open Access Journals (Sweden)

    M. K. El Debs

    Full Text Available Bearing pads are used in precast concrete connections to avoid concentrated stresses in the contact area between the precast elements. In the present research, the bearing pads are Portland cement mortar with styrene-butadiene latex (SB, lightweight aggregate (expanded vermiculite-term and short fibers (polypropylene, glass and PVA, in order to obtain a material with low modulus of elasticity and high tenacity, compared with normal Portland cement mortar. The objective of this paper is to analyze the influence of surface roughness on the pads and test other types of polypropylene fibers. Tests were carried out to characterize the composite and test on bearing pads. Characterization tests show compressive strength of 41MPa and modulus of elasticity of 12.8GPa. The bearing pads tests present 30% reduction of stiffness in relation to a reference mortar. The bearing pads with roughness on both sides present a reduction up to 30% in stiffness and an increase in accumulated deformation of more than 120%, regarding bearing pads with both sides smooth.

  2. Influence of Surface Roughness of Stainless steel on Microbial Adhesion

    DEFF Research Database (Denmark)

    Bagge, D.; Hilbert, Lisbeth Rischel; Gram, L.

    2002-01-01

    status of the surface; it is assumed that microorganisms hide in scratches and cracks. It is also believed that the smoother a surface the better. And a surface with a few microorganisms after cleaning and disinfection is more hygienic and has a lower risk for cross contamination than a surface with many...

  3. Spatial characteristics of secondary flow in a turbulent boundary layer over longitudinal surface roughness

    Science.gov (United States)

    Hwang, Hyeon Gyu; Lee, Jae Hwa

    2017-11-01

    Direct numerical simulations of turbulent boundary layers (TBLs) over spanwise heterogeneous surface roughness are performed to investigate the characteristics of secondary flow. The longitudinal surface roughness, which features lateral change in bed elevation, is described by immersed boundary method. The Reynolds number based on the momentum thickness is varied in the range of Reθ = 300-900. As the TBLs over the roughness elements spatially develop in the streamwise direction, a secondary flow emerges in a form of counter-rotating vortex pair. As the spanwise spacing between the roughness elements and roughness width vary, it is shown that the size of the secondary flow is determined by the valley width between the roughness elements. In addition, the strength of the secondary flow is mostly affected by the spanwise distance between the cores of the secondary flow. Analysis of the Reynolds-averaged turbulent kinetic energy transport equation reveals that the energy redistribution terms in the TBLs over-the ridge type roughness play an important role to derive low-momentum pathways with upward motion over the roughness crest, contrary to the previous observation with the strip-type roughness. This research was supported by the National Research Foundation of Korea (NRF) funded by the Ministry of Education (NRF-2017R1D1A1A09000537) and the Ministry of Science, ICT & Future Planning (NRF-2017R1A5A1015311).

  4. Influence of the surface roughness on the fatigue properties in ausferritic ductile irons (ADI

    Directory of Open Access Journals (Sweden)

    Svenningsson Roger

    2014-06-01

    Full Text Available Heat treatment of cast ductile iron (DI to ausferritic ductile iron (ADI is known to increase fatigue properties. However, the surface roughness of the cast material is also of significant importance. In this investigation, test rods with seven different surface qualities were cast from the same melt i.e. with same chemical composition. The surfaces of the test rods were varied by a number of parameters; grain size of the moulding sand, coated or non-coated mould surfaces, as-cast or machined and polished, shot peened or not. In addition, a reference material in conventional DI was cast and tested. All eight series were subjected to high-cycle fatigue bending tests. The results show that surface defects, such as micro porosity and minor inclusions drastically decrease the fatigue properties. For some ADI materials the stress amplitude limit was actually lower compared to the non-heat treated DI. The machined, polished and shot-peened material demonstrated the best fatigue properties, which is as expected.

  5. Three-dimensional evaluation of surface roughness of resin composites after finishing and polishing.

    Science.gov (United States)

    Nair, Veena S; Sainudeen, Shan; Padmanabhan, Prabeesh; Vijayashankar, L V; Sujathan, Unu; Pillai, Rajesh

    2016-01-01

    This study aims to investigate the effects of finishing and polishing procedures on four novel resin composites using three-dimensional optical profilometer. Four composites classified according to their filler size, were selected: Filtek™ Z350 XT/Nanofill (3M™ ESPE™), Esthet-X HD/Hybrid (Dentsply Caulk), Te Econom/Microfill (Ivoclar Vivadent(®)), Tetric EvoCeram(®) /Nanohybrid (Ivoclar Vivadent(®)). Composite specimens were made in Plexiglass mold and polished with Soflex (3M ESPE), Enhance + Pogo (Dentsply Caulk). Both the systems were used according to the manufacturers' instructions, and the polished surfaces were assessed with an optical profilometer. Kruskal-Wallis test and further pairwise comparison were performed by Mann-Whitney test. The smoothest surfaces for all the resin composites tested were obtained from the Mylar strip; statistically significant differences were observed among them (P = 0.001). The order of composites was ranked from the lowest to highest surface roughness; Filtek Z350 XT Econom < Tetric EvoCeram < Esthet XHD. Pairwise multiple comparison with Mann-Whitney test showed Filtek Z350 to have the smoothest surface and the least with Teric EvoCeram. Among the polishing systems, Soflex showed the smoothest surface and was significantly different from Pogo (P = 0.046). The effectiveness of the polishing systems seems to be dependent on the material used, treatment modality and also on the filler particle size.

  6. The effects of crushing surface roughness on the crushing characteristics of composite tubes

    Science.gov (United States)

    Farley, Gary L.; Wolterman, Richard L.; Kennedy, John M.

    1992-01-01

    The effects of crushing-surface roughness on the energy-absorption capability of graphite and glass-epoxy composite tubes were investigated. Fifty different combinations of fiber, matrix, and specimen ply orientation were evaluated. Two different crushing surface roughnesses were used in this investigation. Crushing surface significantly influences the energy-absorption capability only of tubes that crush in the lamina bending crushing mode; tubes that crush in other modes are not influenced because their lamina bundles do not slide against the crushing surface. Those tubes that crush in the lamina bending mode can achieve higher, lower, or no change in energy-absorption capability as crushing surface roughness increases. If the fiber failure strain of tubes that crush in the lamina bending crushing mode exceeds the matrix failure strain then the energy-absorption capability increases as crushing surface roughness increases. However, if the matrix failure strain exceeds the fiber failure strain then the energy-absorption capability increases as crushing surface roughness decreases. Energy-absorption capability is uninfluenced by crushing surface roughness for tubes that have equal fiber and matrix failure strains.

  7. Effects of surface roughness on plastic strain localization in polycrystalline aggregates

    Directory of Open Access Journals (Sweden)

    Guilhem Yoann

    2014-06-01

    Full Text Available The surface state of mechanical components differs according to applied loadings. Industrial processes may produce specific features at the surface, such as roughness, local hardening, residual stresses or recrystallization. Under fatigue loading, all these parameters will affect the component lifetime, but in different manner. A better understanding of each surface state parameter, separately first and then all combined, will provide a better prediction of fatigue life. The study focuses on the effect of surface roughness. Crystal plasticity finite element computations have been carried out on three-dimensional polycrystalline aggregates with different roughness levels. Local mechanical fields have been analyzed both at the surface and inside the bulk to highlight the competition between crystallography and roughness to impose localization patterns. As soon as surface roughness is strong enough, classical localization bands driven by grains orientation are replaced by localizations patterns driven by the local roughness topology. Nevertheless, this effect tends to decrease gradually under the surface, and it becomes usually negligible after the first layer of grains. The discussion allows us to characterize the influence of the surface state on the local mechanical fields.

  8. Surface roughness and morphology of three nanocomposites after two different polishing treatments by a multitechnique approach.

    Science.gov (United States)

    Janus, J; Fauxpoint, G; Arntz, Y; Pelletier, H; Etienne, O

    2010-05-01

    The purpose of this study was to assess the surface roughness and morphology of three nanocomposites polished with two different polishing systems. Specimens made of hybrid composite (Tetric Ceram [TC] as control) and nanocomposites: nanofilled (Filtek Supreme [FS]), nanofilled hybrid (Grandio [Gr]), complex nanofilled hybrid (Synergy D6 [Syn]) were polished with CompoSystem [CS] or Sof-Lex [SL] polishing discs. The average surface roughness (Ra) before and after polishing was measured using optical profilometry. Both AFM and SEM techniques were additionally used to analyze the surface morphology after polishing with the aim of relating the surface morphology and the surface roughness. Statistical analysis was done by ANOVA using a general linear model (alpha=0.05) with an adjustment for multiple comparisons. Within the same polishing system, FS exhibited the smoothest surface, followed by Syn, TC and Gr (p<0.0001). Sof-Lex polishing discs produced the smoothest surface compared to CompoSystem (p<0.0001). AFM and SEM observations confirmed that the surface roughness was related to the surface morphology and to the average filler size. Positive correlation between the average filler size and the surface roughness suggest that using nanoparticles in the formulation does not necessary improve the surface texture. The nanofilled composite FS, which contains only nanofillers, showed the best results when associated to Sof-Lex polishing discs. 2010 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  9. Beyond the lotus effect: roughness influences on wetting over a wide surface-energy range.

    Science.gov (United States)

    Spori, Doris M; Drobek, Tanja; Zürcher, Stefan; Ochsner, Mirjam; Sprecher, Christoph; Mühlebach, Andreas; Spencer, Nicholas D

    2008-05-20

    To enhance our understanding of liquids in contact with rough surfaces, a systematic study has been carried out in which water contact angle measurements were performed on a wide variety of rough surfaces with precisely controlled surface chemistry. Surface morphologies consisted of sandblasted glass slides as well as replicas of acid-etched, sandblasted titanium, lotus leaves, and photolithographically manufactured golf-tee shaped micropillars (GTMs). The GTMs display an extraordinarily stable, Cassie-type hydrophobicity, even in the presence of hydrophilic surface chemistry. Due to pinning effects, contact angles on hydrophilic rough surfaces are shifted to more hydrophobic values, unless roughness or surface energy are such that capillary forces become significant, leading to complete wetting. The observed hydrophobicity is thus not consistent with the well-known Wenzel equation. We have shown that the pinning strength of a surface is independent of the surface chemistry, provided that neither capillary forces nor air enclosure are involved. In addition, pinning strength can be described by the axis intercept of the cosine-cosine plot of contact angles for rough versus flat surfaces with the same surface chemistries.

  10. The Effect of Prophylactic Polishing Pastes on Surface Roughness of Indirect Restorative Materials

    Directory of Open Access Journals (Sweden)

    Esra Can Say

    2014-01-01

    Full Text Available The purpose of this study was to evaluate the influence of prophylactic polishing pastes (PPP; Detartrine (DT, Topex (TP on surface roughness (Ra of indirect composites (IRC; Tescera (TES, Gradia (GRD, and Estenia C&B (EST, a glass ceramic (Empress 2 layering (E2, and a leucite reinforced glass ceramic (Empress Esthetic (EE with two different (glazed (G; polished (P surface preparations. A total of 90 IRC and 120 ceramic discs, 8 mm in diameter and 2 mm thick, were prepared. E2 and EE specimens were randomly divided into two groups (n=30. One group was glazed (GE2; GEE, while the other group was polished (PE2; PEE the same as the IRCs. The specimens in each group were subsequently divided into three subgroups: control (C, DT, and TP. Ra (μm was evaluated with a profilometer. Data were analyzed by Kruskal Wallis, followed by the Dunn's multiple comparison tests P0.05. PE2 and PEE were not affected by DT or TP P>0.05, while GE2 and GEE exhibited significant roughening after TP P<0.05. Surface roughness of IRCs and glazed ceramics can be affected by PPP applications.

  11. Effects of different polishing techniques on the surface roughness of dental porcelains

    Directory of Open Access Journals (Sweden)

    Işil Sarikaya

    2010-02-01

    Full Text Available OBJECTIVE: The purpose of this study was to evaluate the effects of different polishing techniques on the surface roughness of dental porcelains. MATERIAL AND METHODS: Fifty-five cylindirical specimens (15x2 mm were prepared for each feldspathic (Vita VMK 95, Ceramco III and low-fusing dental porcelain (Matchmaker. Fifty-five specimens of machinable feldspathic porcelain blocks (Vitablocs Mark II, (12x14x18 mm were cut into 2-mm-thick slices (12x14 mm with low speed saw. The prepared specimens were divided into 11 groups (n=5 representing different polishing techniques including control ((C no surface treatment, glaze (G and other 9 groups that were finished and polished with polishing discs (Sof-Lex (Sl, two porcelain polishing kits (NTI (Pk, Dialite II (Di, a diamond polishing paste (Sparkle (Sp, a zirconium silicate based cleaning and polishing prophy paste (Zircate (Zr, an aluminum oxide polishing paste (Prisma Gloss (Pg, and combinations of them. The surface roughness of all groups was measured with a profilometer. The data were analyzed with a 2-way analysis of variance, and the mean values were compared by the Tukey Honestly Significant Difference test (a=0.05. RESULTS: For all porcelain material groups, the lowest Ra values were observed in Group Gl, Group Sl, Group Pk, and Group Di, which were not significantly different from each other (p>0.05.When comparing the 4 different porcelain materials, the machinable feldspathic porcelain block group (Mark II demonstrated statistically significantly less Ra values than the other porcelain materials tested (p<0.05. No significant difference was observed between the VMK 95 and Ceramco III porcelain groups (p=0.919, also these groups demonstrated the highest Ra values. CONCLUSION: Subjected to surface roughness, the surfaces obtained with polishing and/or cleaning-prophy paste materials used alone were rougher compared to the surfaces finished using Sof-lex, Dialite, and NTI polishing kit

  12. Roughness characterization of EUV multilayer coatings and ultra-smooth surfaces by light scattering

    Science.gov (United States)

    Trost, M.; Schröder, S.; Lin, C. C.; Duparré, A.; Tünnermann, A.

    2012-09-01

    Optical components for the extreme ultraviolet (EUV) face stringent requirements for surface finish, because even small amounts of surface and interface roughness can cause significant scattering losses and impair image quality. In this paper, we investigate the roughness evolution of Mo/Si multilayers by analyzing the scattering behavior at a wavelength of 13.5 nm as well as taking atomic force microscopy (AFM) measurements before and after coating. Furthermore, a new approach to measure substrate roughness is presented, which is based on light scattering measurements at 405 nm. The high robustness and sensitivity to roughness of this method are illustrated using an EUV mask blank with a highspatial frequency roughness of as low as 0.04 nm.

  13. Effect of disinfection and sterilization on the tensile strength, surface roughness, and wettability of elastomers.

    Science.gov (United States)

    Kotha, Sunil Babu; Ramakrishnaiah, Ravikumar; Devang Divakar, Darshan; Celur, Sree Lalita; Qasim, Saad; Matinlinna, Jukka P

    2017-11-01

    The aim of the present study was to evaluate the effect of chemical disinfection, autoclave, and microwave sterilization on some of the key properties of elastomers. Five polyvinylsiloxane elastomeric impression materials were evaluated. Forty samples were fabricated from each material. The samples were randomly selected and assigned to four experimental groups with 50 samples each: group I, control; group II,chemical disinfection; group III, autoclave sterilization; and group IV, microwave sterilization. The differences in the mean values were contrasted and compared with the control group and analyzed using two-way analysis of variance (P autoclave sterilization had no significant effect on the tensile strength and surface roughness, whereas microwave sterilization showed a statistically-significant reduction in tensile strength, and an increase in surface roughness. None of the disinfection and sterilization techniques had a significant effect on wettability. However, autoclave and microwave sterilization resulted in an increase in hydrophilicity of all the materials tested. Chemical disinfection and autoclave sterilization had no statistically-significant effect on the tested properties of elastomers, thus autoclave sterilization can be considered as an alternative and an effective mode of disinfection and sterilization to eliminate all forms of disease causing microorganisms from dental impressions. © 2016 John Wiley & Sons Australia, Ltd.

  14. Fast, Statistical Model of Surface Roughness for Ion-Solid Interaction Simulations and Efficient Code Coupling

    Science.gov (United States)

    Drobny, Jon; Curreli, Davide; Ruzic, David; Lasa, Ane; Green, David; Canik, John; Younkin, Tim; Blondel, Sophie; Wirth, Brian

    2017-10-01

    Surface roughness greatly impacts material erosion, and thus plays an important role in Plasma-Surface Interactions. Developing strategies for efficiently introducing rough surfaces into ion-solid interaction codes will be an important step towards whole-device modeling of plasma devices and future fusion reactors such as ITER. Fractal TRIDYN (F-TRIDYN) is an upgraded version of the Monte Carlo, BCA program TRIDYN developed for this purpose that includes an explicit fractal model of surface roughness and extended input and output options for file-based code coupling. Code coupling with both plasma and material codes has been achieved and allows for multi-scale, whole-device modeling of plasma experiments. These code coupling results will be presented. F-TRIDYN has been further upgraded with an alternative, statistical model of surface roughness. The statistical model is significantly faster than and compares favorably to the fractal model. Additionally, the statistical model compares well to alternative computational surface roughness models and experiments. Theoretical links between the fractal and statistical models are made, and further connections to experimental measurements of surface roughness are explored. This work was supported by the PSI-SciDAC Project funded by the U.S. Department of Energy through contract DOE-DE-SC0008658.

  15. Asperity Interaction and Substrate Deformation in Statistical Summation Models of Contact Between Rough Surfaces

    NARCIS (Netherlands)

    Vakis, Antonis I.

    A method is proposed to account for asperity interaction and bulk substrate deformation in models that utilize statistical summation of asperity forces to characterize contact between rough surfaces. Interaction deformations of noncontacting asperities are calculated based on the probability that

  16. Comparison of the surface roughness of gypsum models constructed using various impression materials and gypsum products

    Directory of Open Access Journals (Sweden)

    Yi-Chih Chang

    2016-03-01

    Conclusion: The surface roughness of stone models was mainly determined by the type of alginate impression material, and was less affected by the type of silicone rubber impression material or gypsum product, or the storage time before repouring.

  17. Effect of surface roughness scattering on the transport properties of a 2DEG

    International Nuclear Information System (INIS)

    Yarar, Z.

    2004-01-01

    In this work surface roughness scattering of electrons in a two dimensional electron gas (2DEG) formed at heterojunction interfaces is investigated for various auto-correlation functions. Gaussian, exponential and Lorentzian auto-correlation functions are used to represent surface roughness. Poisson and Schrodinger equations are solved self consistently at the hetero interface to find the energy levels, the wave functions corresponding to each level and electron concentrations at each level. Using these wave functions and the auto-correlation functions mentioned above, the scattering rates due to surface roughness are calculated. Scattering rates resulting from acoustic and optical phonons are also calculated. These rates are used to study the transport properties of the two dimensional electrons using ensemble Monte Carlo method at various temperatures. Emphasis is given to the effect of surface roughness scattering on the transport properties of the electrons

  18. Surface roughness optimization in machining of AZ31 magnesium alloy using ABC algorithm

    Directory of Open Access Journals (Sweden)

    Abhijith

    2018-01-01

    Full Text Available Magnesium alloys serve as excellent substitutes for materials traditionally used for engine block heads in automobiles and gear housings in aircraft industries. AZ31 is a magnesium alloy finds its applications in orthopedic implants and cardiovascular stents. Surface roughness is an important parameter in the present manufacturing sector. In this work optimization techniques namely firefly algorithm (FA, particle swarm optimization (PSO and artificial bee colony algorithm (ABC which are based on swarm intelligence techniques, have been implemented to optimize the machining parameters namely cutting speed, feed rate and depth of cut in order to achieve minimum surface roughness. The parameter Ra has been considered for evaluating the surface roughness. Comparing the performance of ABC algorithm with FA and PSO algorithm, which is a widely used optimization algorithm in machining studies, the results conclude that ABC produces better optimization when compared to FA and PSO for optimizing surface roughness of AZ 31.

  19. Improvement of sidewall surface roughness in silicon-on-insulator rib waveguides

    Science.gov (United States)

    Gao, F.; Wang, Y.; Cao, G.; Jia, X.; Zhang, F.

    2005-09-01

    Silicon-on-insulator (SOI) rib waveguides with residual sidewall roughness were fabricated through inductive coupled plasma reactive ion etching (ICPRIE) process. The sidewall surface morphology was characterized by scan electron microscope (SEM), and the root mean square (rms) roughness of the sidewall surface was directly measured by atomic force microscope (AFM). Sidewall surface roughness is the dominant scattering loss source. The ripples on the sidewall surface could be eliminated by mixed ICPRIE, and the rms roughness could be low down to 0.3 nm after thermal oxidation and hf rinse. According to the scattering theory developed by Payne and Lacey, the scattering loss could be minimized to below 0.01 dB/cm. The results indicated that the scattering loss would be a sharp fall by the combination with these two techniques.

  20. Effects of process parameters on surface roughness in abrasive waterjet cutting of aluminium

    Science.gov (United States)

    Chithirai Pon Selvan, M.; Mohana Sundara Raju, N.; Sachidananda, H. K.

    2012-12-01

    Abrasive waterjet cutting is a novel machining process capable of processing wide range of hard-to-cut materials. Surface roughness of machined parts is one of the major machining characteristics that play an important role in determining the quality of engineering components. This paper shows the influence of process parameters on surface roughness ( R a) which is an important cutting performance measure in abrasive waterjet cutting of aluminium. Taguchi's design of experiments was carried out in order to collect surface roughness values. Experiments were conducted in varying water pressure, nozzle traverse speed, abrasive mass flow rate and standoff distance for cutting aluminium using abrasive waterjet cutting process. The effects of these parameters on surface roughness have been studied based on the experimental results.

  1. Analytic study of a rolling sphere on a rough surface

    Directory of Open Access Journals (Sweden)

    Olivia A. Florea

    2016-11-01

    Full Text Available In this paper it is realized an analytic study of the rolling’s sphere on a rough horizontal plane under the action of its own gravity. The necessities of integration of the system of dynamical equations of motion lead us to find a reference system where the motion equations should be transformed into simpler expressions and which, in the presence of some significant hypothesis to permit the application of some original methods of analytical integration. In technical applications, the bodies may have a free rolling motion or a motion constrained by geometrical relations in assemblies of parts and machine parts. This study involves a lot of investigations in the field of tribology and of applied dynamics accompanied by experiments. Multiple recordings of several trajectories of the sphere, as well as their treatment of images, also followed by statistical processing experimental data allowed highlighting a very good agreement between the theoretical findings and experimental results.

  2. Surface roughness and Candida albicans biofilm formation on a reline resin after long-term chemical disinfection and toothbrushing.

    Science.gov (United States)

    Izumida, Fernanda E; Jorge, Janaína H; Ribeiro, Roberta C; Pavarina, Ana C; Moffa, Eduardo B; Giampaolo, Eunice T

    2014-12-01

    Routine cleaning of a denture may increase the surface roughness of the material. The purpose of this study was to investigate the effect of denture cleansers and time on the roughness and Candida albicans biofilm formation on a reline resin. Specimens of Tokuyama Rebase Fast II (20 × 10 × 2 mm) were prepared and divided into 9 groups (n=15): Test groups were toothbrushed (30 cycles per day) in 1 of the following solutions: water, soap, or toothpaste. After toothbrushing, the specimens were immersed in solutions of water, sodium perborate, or chlorhexidine. These treatments were done once a day for 365 days. The surface roughness was evaluated at 0, 7, 15, 30, 90, 180, 270, and 365 days, and the C albicans biofilm formation was measured after 365 days. The roughness data were analyzed by 3-way repeated measures ANOVA and the Tukey test (α=.05), and the C albicans biofilm formation was analyzed by 2-way ANOVA. Significant differences were found in the toothbrush and time interaction and in the toothbrush, immersion, and time interaction (Ptoothbrush agent and chemical disinfection (P=.085) or between chemical disinfection and time interaction (P=.604). Brushing with dentifrice (PPb and PCh) showed a gradual decrease in surface roughness. The comparison among groups showed that PCh produced the lowest values of roughness. For C albicans biofilm formation, no significant differences were found among the experimental groups. The roughness values ranged from 0.31 to 0.69 μm for all evaluated groups. For all groups, no significant differences were found in the quantification of C albicans. Copyright © 2014 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

  3. How surface roughness affects the angular dependence of the sputtering yield

    International Nuclear Information System (INIS)

    Hu, A.; Hassanein, A.

    2012-01-01

    Comprehensive model is developed to study the impact of surface roughness on the angular dependence of sputtering yield. Instead of assuming surfaces to be flat or composed of exact self-similar fractals, we developed a new method to describe the surfaces. Random fractal surfaces generated by midpoint displacement algorithm in computer graphics area and Support vector machine algorithm in pattern recognition area are combined with the Monte Carlo ion bombardment simulation code, i.e., Ion Transport in Materials and Compounds (ITMC) code . With this new fractal version of ITMC-F, we successfully simulated the angular dependence of sputtering yield for various ion-target combinations. Examples are given for 5 keV Ar ions bombarding iron, graphite, and silicon surfaces, with the input surface roughness exponent directly depicted from experimental data. Comparison is made with previous models to account for surface roughness and recent experimental data. The ITMC-F code showed good agreement with the experimental data.

  4. Scanning near-field optical microscopy on rough surfaces: Applications in chemistry, biology, and medicine

    OpenAIRE

    Kaupp, Gerd

    2006-01-01

    Shear-force apertureless scanning near-field optical microscopy (SNOM) with very sharp uncoated tapered waveguides relies on the unexpected enhancement of reflection in the shear-force gap. It is the technique for obtaining chemical (materials) contrast in the optical image of “real world” surfaces that are rough and very rough without topographical artifacts, and it is by far less complicated than other SNOM techniques that can only be used for very flat surfaces. The ex...

  5. Soil surface roughness modeling: limit of global characterization in remote sensing

    Science.gov (United States)

    Chimi-Chiadjeu, O.; Vannier, E.; Dusséaux, R.; Taconet, O.

    2013-10-01

    Many scientists use a global characterization of bare soil surface random roughness. Surface roughness is often characterized by statistical parameters deduced from its autocorrelation function. Assuming an autocorrelation model and a Gaussian height distribution, some authors have developed algorithms for numerical generation of soil surfaces that have the same statistical properties. This approach is widespread and does not take into account morphological aspects of the soil surface micro-topography. Now a detail surface roughness analysis reveals that the micro-topography is structured by holes, aggregates and clods. In the present study, we clearly show that when describing surface roughness as a whole, some information related to morphological aspects is lost. Two Digital Elevation Model (DEM) of a same natural seedbed surface were recorded by stereo photogrammetry. After estimating global parameters of these natural surfaces, we generated numerical surfaces of the same average characteristics by linear filtering. Big aggregates and clods were then captured by a contour-based approach. We show that the two-dimensional autocorrelation functions of generated surfaces and of the two agricultural surfaces are close together. Nevertheless, the number and shape of segmented object contours change from generated surfaces to the natural surfaces. Generated surfaces show fewer and bigger segmented objects than in the natural case. Moreover, the shape of some segmented objects is unrealistic in comparison to real clods, which have to be convex and of low circularity.

  6. Gecko toe and lamellar shear adhesion on macroscopic, engineered rough surfaces.

    Science.gov (United States)

    Gillies, Andrew G; Henry, Amy; Lin, Hauwen; Ren, Angela; Shiuan, Kevin; Fearing, Ronald S; Full, Robert J

    2014-01-15

    The role in adhesion of the toes and lamellae - intermediate-sized structures - found on the gecko foot remains unclear. Insight into the function of these structures can lead to a more general understanding of the hierarchical nature of the gecko adhesive system, but in particular how environmental topology may relate to gecko foot morphology. We sought to discern the mechanics of the toes and lamellae by examining gecko adhesion on controlled, macroscopically rough surfaces. We used live Tokay geckos, Gekko gecko, to observe the maximum shear force a gecko foot can attain on an engineered substrate constructed with sinusoidal patterns of varying amplitudes and wavelengths in sizes similar to the dimensions of the toes and lamellae structures (0.5 to 6 mm). We found shear adhesion was significantly decreased on surfaces that had amplitudes and wavelengths approaching the lamella length and inter-lamella spacing, losing 95% of shear adhesion over the range tested. We discovered that the toes are capable of adhering to surfaces with amplitudes much larger than their dimensions even without engaging claws, maintaining 60% of shear adhesion on surfaces with amplitudes of 3 mm. Gecko adhesion can be predicted by the ratio of the lamella dimensions to surface feature dimensions. In addition to setae, remarkable macroscopic-scale features of gecko toes and lamellae that include compliance and passive conformation are necessary to maintain contact, and consequently, generate shear adhesion on macroscopically rough surfaces. Findings on the larger scale structures in the hierarchy of gecko foot function could provide the biological inspiration to drive the design of more effective and versatile synthetic fibrillar adhesives.

  7. Effects of Er:YAG laser treatments on surface roughness of base metal alloys.

    Science.gov (United States)

    Kunt, Göknil Ergün; Güler, Ahmet Umut; Ceylan, Gözlem; Duran, Ibrahim; Ozkan, Pelin; Kirtiloğlu, Tuğrul

    2012-01-01

    We investigated the effects of different Er:YAG laser treatments on the surface roughness of base metal alloys. A total of 36 specimens were prepared of two base metal alloys (Wiron 99, Bellabond plus). The surfaces of the specimens were standardized by gradual wet grinding with 320-, 600-, 800- and 1,000-grit silicon carbide paper for 10 s each on a grinding machine at 300 rpm. Specimens of each alloy were randomly divided into six groups (n = 6) comprising a control group (group C), a group sandblasted with Al(2)O(3) powder at 60 psi for 10 s through a nozzle at a distance of 10 mm (group S), and four Er:YAG laser (Fotona AT) treatment groups. The laser treatment groups were as follows: 500 mJ, 10 Hz, 100 μs (group 500MSP); 500 mJ, 10 Hz, 300 μs (group 500SP); 400 mJ, 10 Hz, 100 μs (group 400MSP); and 400 mJ, 10 Hz, 300 μs (group 400SP). Surface roughness measurements (Ra) were performed using a profilometer. The data were analysed by two-way ANOVA, and mean values were compared using Tukey's HSD test (α = 0.05). According to the two-way ANOVA results, the base metal alloys and interaction between base metal alloy and surface treatment were not statistically significant different (p > 0.05), the surface treatments were significantly different (p metal alloy groups, no significant differences were observed among the control, 400MSP, and 400SP groups (p = 0.912), and these groups demonstrated the lowest Ra values. The highest Ra value was observed in group S (p laser treatment at 400 and 500 mJ/10 Hz is not an alternative method for surface roughening of base metal alloys.

  8. The relationship between the particle properties, mechanical behavior, and surface roughness of some pharmaceutical excipient compacts

    International Nuclear Information System (INIS)

    Narayan, Padma; Hancock, Bruno C.

    2003-01-01

    Several common pharmaceutical excipient powders were compacted at a constant solid fraction (SF) in order to study the relationship between powder properties, compact surface roughness, and compact mechanical properties such as hardness, elasticity, and brittleness. The materials used in this study included microcrystalline cellulose (MCC), fumaric acid, mannitol, lactose monohydrate, spray dried lactose, sucrose, and dibasic calcium phosphate dihydrate. A slow consolidation process was used to make compacts at a SF of 0.85 (typical for most pharmaceutical tablets) from single excipient components. A model was proposed to describe the surface roughness of compacts based on the brittle or ductile deformation tendencies of the powder materials. The roughness profile would also be dependent upon the magnitude of the compression stress in relation to the yield stress (onset of irreversible deformation) values of the excipients. It was hypothesized that brittle materials would produce smooth compacts with high surface variability due to particle fracture, and the converse would apply for ductile materials. Compact surfaces should be smoother if the materials were compressed above their yield pressure values. Non-contact optical profilometry was used along with scanning electron microscopy to quantify and characterize the surface morphology of the excipient compacts. The roughness parameters R a (average roughness), R q (RMS roughness), R q /R a (ratio describing surface variability), and R sk (skewness) were found to correlate with the deformation properties of the excipients. Brittle materials such as lactose, sucrose, and calcium phosphate produced compacts with low values of R a and R q , high variability, and negative R sk . The opposite was found with plastic materials such as MCC, mannitol, and fumaric acid. The highly negative skewness values for brittle material compacts may indicate their propensity to be vulnerable to cracks or surface defects. These findings

  9. Influence of full-contour zirconia surface roughness on wear of glass-ceramics.

    Science.gov (United States)

    Luangruangrong, Palika; Cook, N Blaine; Sabrah, Alaa H; Hara, Anderson T; Bottino, Marco C

    2014-04-01

    The purpose of this study was to evaluate the influence of full-contour (Y-TZP) zirconia surface roughness (glazed vs. as-machined) on the wear behavior of glass-ceramics. Thirty-two full contour Y-TZP (Diazir®) specimens (hereafter referred to as zirconia sliders) (ϕ = 2 mm, 1.5 mm in height) were fabricated using CAD/CAM and sintered according to the manufacturer's instructions. Zirconia sliders were embedded in brass holders using acrylic resin and then randomly assigned (n = 16) according to the surface treatment received, that is, as-machined or glazed. Glass-ceramic antagonists, Empress/EMP and e.max/EX, were cut into tabs (13 × 13 × 2 mm(3) ), wet-finished, and similarly embedded in brass holders. Two-body pin-on-disk wear testing was performed at 1.2 Hz for 25,000 cycles under a 3 kg load. Noncontact profilometry was used to measure antagonist height (μm) and volume loss (mm(3) ). Qualitative data of the zirconia testing surfaces and wear tracks were obtained using SEM. Statistics were performed using ANOVA with a significance level of 0.05. As-machined yielded significantly higher mean roughness values (Ra = 0.83 μm, Rq = 1.09 μm) than glazed zirconia (Ra = 0.53 μm, Rq = 0.78 μm). Regarding glass-ceramic antagonist loss, as-machined zirconia caused significantly less mean height and volume loss (68.4 μm, 7.6 mm(3) ) for EMP than the glazed group (84.9 μm, 9.9 mm(3) ), while no significant differences were found for EX. Moreover, EMP showed significantly lower mean height and volume loss than EX (p glass-ceramics tested. e.max wear was not affected by zirconia surface roughness; however, Empress wear was greater when opposing glazed zirconia. Overall, surface glazing on full-contour zirconia did not minimize glass-ceramic wear when compared with as-machined zirconia. © 2013 by the American College of Prosthodontists.

  10. Effect of the surface roughness on interfacial properties of carbon fibers reinforced epoxy resin composites

    International Nuclear Information System (INIS)

    Song Wei; Gu Aijuan; Liang Guozheng; Yuan Li

    2011-01-01

    The effect of the surface roughness on interfacial properties of carbon fibers (CFs) reinforced epoxy (EP) resin composite is studied. Aqueous ammonia was applied to modify the surfaces of CFs. The morphologies and chemical compositions of original CFs and treated CFs (a-CFs) were characterized by Atomic Force Microscopy (AFM), and X-ray Photoelectron Spectroscopy (XPS). Compared with the smooth surface of original CF, the surface of a-CF has bigger roughness; moreover, the roughness increases with the increase of the treating time. On the other hand, no obvious change in chemical composition takes place, indicating that the treating mechanism of CFs by aqueous ammonia is to physically change the morphologies rather than chemical compositions. In order to investigate the effect of surface roughness on the interfacial properties of CF/EP composites, the wettability and Interfacial Shear Strength (IFSS) were measured. Results show that with the increase of the roughness, the wettabilities of CFs against both water and ethylene glycol improves; in addition, the IFSS value of composites also increases. These attractive phenomena prove that the surface roughness of CFs can effectively overcome the poor interfacial adhesions between CFs and organic matrix, and thus make it possible to fabricate advanced composites based on CFs.

  11. Modeling and optimization of surface roughness in single point incremental forming process

    Directory of Open Access Journals (Sweden)

    Suresh Kurra

    2015-07-01

    Full Text Available Single point incremental forming (SPIF is a novel and potential process for sheet metal prototyping and low volume production applications. This article is focuses on the development of predictive models for surface roughness estimation in SPIF process. Surface roughness in SPIF has been modeled using three different techniques namely, Artificial Neural Networks (ANN, Support Vector Regression (SVR and Genetic Programming (GP. In the development of these predictive models, tool diameter, step depth, wall angle, feed rate and lubricant type have been considered as model variables. Arithmetic mean surface roughness (Ra and maximum peak to valley height (Rz are used as response variables to assess the surface roughness of incrementally formed parts. The data required to generate, compare and evaluate the proposed models have been obtained from SPIF experiments performed on Computer Numerical Control (CNC milling machine using Box–Behnken design. The developed models are having satisfactory goodness of fit in predicting the surface roughness. Further, the GP model has been used for optimization of Ra and Rz using genetic algorithm. The optimum process parameters for minimum surface roughness in SPIF have been obtained and validated with the experiments and found highly satisfactory results within 10% error.

  12. Wind-Tunnel Investigations of Blunt-Body Drag Reduction Using Forebody Surface Roughness

    Science.gov (United States)

    Whitmore, Stephen A.; Sprague, Stephanie; Naughton, Jonathan W.; Curry, Robert E. (Technical Monitor)

    2001-01-01

    This paper presents results of wind-tunnel tests that demonstrate a novel drag reduction technique for blunt-based vehicles. For these tests, the forebody roughness of a blunt-based model was modified using micomachined surface overlays. As forebody roughness increases, boundary layer at the model aft thickens and reduces the shearing effect of external flow on the separated flow behind the base region, resulting in reduced base drag. For vehicle configurations with large base drag, existing data predict that a small increment in forebody friction drag will result in a relatively large decrease in base drag. If the added increment in forebody skin drag is optimized with respect to base drag, reducing the total drag of the configuration is possible. The wind-tunnel tests results conclusively demonstrate the existence of a forebody dragbase drag optimal point. The data demonstrate that the base drag coefficient corresponding to the drag minimum lies between 0.225 and 0.275, referenced to the base area. Most importantly, the data show a drag reduction of approximately 15% when the drag optimum is reached. When this drag reduction is scaled to the X-33 base area, drag savings approaching 45,000 N (10,000 lbf) can be realized.

  13. Influence of different staining beverages on color stability, surface roughness and microhardness of silorane and methacrylate-based composite resins.

    Science.gov (United States)

    Karaman, Emel; Tuncer, Duygu; Firat, Esra; Ozdemir, Oguz Suleyman; Karahan, Sevilay

    2014-05-01

    To investigate the influence of different staining beverages on color stability, surface roughness and microhardness of silorane and methacrylate-based composite resins. Three different composite resins (Filtek Silorane, Filtek P60, Filtek Supreme XT) were tested. Thirty cylindrical specimens (10 × 2 mm) per material were prepared and polished with a series of aluminum-oxide polishing disks. Each group was then randomly subdivided into three groups according to the test beverages: distilled water (control), cola and coffee. The samples were immersed into different beverages for 15 days. Color, surface roughness and microhardness values were measured by a spectrophotometer, prophylometer and Vickers hardness device respectively, at baseline and after 15 days. The data were subjected to statistical analysis. Immersion in coffee resulted in a significant discoloration for all the composites tested, although the color change was lower in Filtek Silorane than that of MBCs (p composites tested showed similar surface roughness changes after immersion in different beverages (p > 0.05). Besides coffee caused more roughness change than others. Immersion in coffee caused highest microhardness change in Filtek Supreme XT (p resin composites, depending on the characteristics of the materials.

  14. A computer-aided surface roughness measurement system

    International Nuclear Information System (INIS)

    Hughes, F.J.; Schankula, M.H.

    1983-11-01

    A diamond stylus profilometer with computer-based data acquisitions/analysis system is being used to characterize surfaces of reactor components and materials, and to examine the effects of surface topography on thermal contact conductance. The current system is described; measurement problems and system development are discussed in general terms and possible future improvements are outlined

  15. Comparison Between 2D And 3D Surface Roughness Parameters ...

    African Journals Online (AJOL)

    As part of a research programme, extensive electro discharge machining (EDM) was done so as to generate different spark eroded surfaces. Through surface texture measurements, it has been confirmed that the use of 2D parameters alone is indeed misleading. Thus, in order to comprehensively represent the topography ...

  16. Abrasive wear between rough surfaces in deep drawing

    NARCIS (Netherlands)

    Masen, Marc Arthur; de Rooij, Matthias B.

    2004-01-01

    In tribology, many surface contact models are based on the assumption that surfaces are composed of a collection of small asperities of which the tips are equally sized and spherically shaped and have some kind of statistical height distribution. This approach was used in 1966 by Greenwood and

  17. Over rough and smooth : Amputee gait on an irregular surface

    NARCIS (Netherlands)

    Curtze, Carolin; Hof, At L.; Postema, Klaas; Otten, Bert

    When negotiating irregular surfaces, the control of dynamic stability is challenged. In this study, we compared the adjustments in stepping behaviour and arm-swing of 18 unilateral transtibial amputees and 17 able-bodied participants when walking on flat and irregular surfaces. Experimental findings

  18. Enhancement of vortex induced forces and motion through surface roughness control

    Science.gov (United States)

    Bernitsas, Michael M [Saline, MI; Raghavan, Kamaldev [Houston, TX

    2011-11-01

    Roughness is added to the surface of a bluff body in a relative motion with respect to a fluid. The amount, size, and distribution of roughness on the body surface is controlled passively or actively to modify the flow around the body and subsequently the Vortex Induced Forces and Motion (VIFM). The added roughness, when designed and implemented appropriately, affects in a predetermined way the boundary layer, the separation of the boundary layer, the level of turbulence, the wake, the drag and lift forces, and consequently the Vortex Induced Motion (VIM), and the fluid-structure interaction. The goal of surface roughness control is to increase Vortex Induced Forces and Motion. Enhancement is needed in such applications as harnessing of clean and renewable energy from ocean/river currents using the ocean energy converter VIVACE (Vortex Induced Vibration for Aquatic Clean Energy).

  19. Reduction of vortex induced forces and motion through surface roughness control

    Science.gov (United States)

    Bernitsas, Michael M; Raghavan, Kamaldev

    2014-04-01

    Roughness is added to the surface of a bluff body in a relative motion with respect to a fluid. The amount, size, and distribution of roughness on the body surface is controlled passively or actively to modify the flow around the body and subsequently the Vortex Induced Forces and Motion (VIFM). The added roughness, when designed and implemented appropriately, affects in a predetermined way the boundary layer, the separation of the boundary layer, the level of turbulence, the wake, the drag and lift forces, and consequently the Vortex Induced Motion (VIM), and the fluid-structure interaction. The goal of surface roughness control is to decrease/suppress Vortex Induced Forces and Motion. Suppression is required when fluid-structure interaction becomes destructive as in VIM of flexible cylinders or rigid cylinders on elastic support, such as underwater pipelines, marine risers, tubes in heat exchangers, nuclear fuel rods, cooling towers, SPAR offshore platforms.

  20. Interactions of light with rough dielectric surfaces - Spectral reflectance and polarimetric properties

    Science.gov (United States)

    Yon, S. A.; Pieters, C. M.

    1988-01-01

    The nature of the interactions of visible and NIR radiation with the surfaces of rock and mineral samples was investigated by measuring the reflectance and the polarization properties of scattered and reflected light for slab samples of obsidian and fine-grained basalt, prepared to controlled surface roughness. It is shown that the degree to which radiation can penetrate a surface and then scatter back out, an essential criterion for mineralogic determinations based on reflectance spectra, depends not only upon the composition of the material, but also on its physical condition such as sample grain size and surface roughness. Comparison of the experimentally measured reflectance and polarization from smooth and rough slab materials with the predicted models indicates that single Fresnel reflections are responsible for the largest part of the reflected intensity resulting from interactions with the surfaces of dielectric materials; multiple Fresnel reflections are much less important for such surfaces.

  1. Wakes behind surface-mounted obstacles: Impact of aspect ratio, incident angle, and surface roughness

    Science.gov (United States)

    Tobin, Nicolas; Chamorro, Leonardo P.

    2018-03-01

    The so-called wake-moment coefficient C˜h and lateral wake deflection of three-dimensional windbreaks are explored in the near and far wake. Wind-tunnel experiments were performed to study the functional dependence of C˜h with windbreak aspect ratio, incidence angle, and the ratio of the windbreak height and surface roughness (h /z0 ). Supported with the data, we also propose basic models for the wake deflection of the windbreak in the near and far fields. The near-wake model is based on momentum conservation considering the drag on the windbreak, whereas the far-wake counterpart is based on existing models for wakes behind surface-mounted obstacles. Results show that C˜h does not change with windbreak aspect ratios of 10 or greater; however, it may be lower for an aspect ratio of 5. C˜h is found to change roughly with the cosine of the incidence angle, and to depend strongly on h /z0 . The data broadly support the proposed wake-deflection models, though better predictions could be made with improved knowledge of the windbreak drag coefficient.

  2. The improvement of surface roughness for OAP aluminum mirrors: from terahertz to ultraviolet

    Science.gov (United States)

    Peng, Jilong; Yu, Qian; Shao, Yajun; Wang, Dong; Yi, Zhong; Wang, Shanshan

    2018-01-01

    Aluminum reflector, especially OAP (Off-Axis Parabolic) reflector, has been widely used in terahertz and infrared systems for its low cost, lightweight, good machinability, small size, simple structure, and having the same thermal expansion and contraction with the system structure which makes it have a wide temperature adaptability. Thorlabs, Daheng and other large optical components companies even have Aluminum OAP sold on shelf. Most of the precision Aluminum OAP is fabricated by SPDT (single point diamond turing). Affected by intermittent shock, the roughness of aluminum OAP mirrors through conventional single-point diamond lathes is around 7 nm which limits the scope of application for aluminum mirrors, like in the high power density terahertz/infrared systems and visible/UV optical systems. In this paper, a continuous process frock is proposed, which effectively reduces the influence of turning impact on the mirror roughness. Using this process, an off-axis parabolic aluminum reflector with an effective diameter of 50 mm, off-axis angle of 90 degree is fabricated, and the performances are validated. Measurement by VEECO NT1100 optical profiler with 20× objects, the surface roughness achieves 2.3 nm, and the surface figure error is within λ/7 RMS (λ= 632.8 nm) tested by FISB Aμ Phase laser interferometer with the help of a standard flat mirror. All these technical specifications are close to the traditional glass-based reflectors, and make it possible for using Aluminum reflectors in the higher LIDT (laser induced damage threshold) systems and even for the micro sensor of ionospheric for vacuum ultraviolet micro nano satellites.

  3. Surface roughness characterization of cast components using 3D optical methods

    DEFF Research Database (Denmark)

    Nwaogu, Ugochukwu Chibuzoh; Tiedje, Niels Skat; Hansen, Hans Nørgaard

    made in green sand moulds and the surface roughness parameter (Sa) values were compared with those of the standards. Sa parameter suffices for the evaluation of casting surface texture. The S series comparators showed a better description of the surface of castings after shot blasting than the A series...

  4. Effect of surface mechanical attrition treatment (SMAT) on microhardness, surface roughness and wettability of AISI 316L

    NARCIS (Netherlands)

    Arifvianto, B.; Suyitno, [No Value; Mahardika, M.; Dewo, P.; Iswanto, P. T.; Salim, U. A.

    2011-01-01

    Surface roughness and wettability are among the surface properties which determine the service lifetime of materials. Mechanical treatments subjected to the surface layer of materials are often performed to obtain the desired surface properties and to enhance the mechanical strength of materials. In

  5. Effect of surface roughness on erosion rates of pure copper coupons in pulsed vacuum arc system

    International Nuclear Information System (INIS)

    Rao, Lakshminarayana; Munz, Richard J

    2007-01-01

    Vacuum arc erosion measurements were performed on copper cathodes having different surface roughness and surface patterns in 10 -5 Torr vacuum (1.3324 mPa), in an external magnetic field of 0.04 T. Different surface patterns and surface roughness were created by grit blasting with alumina grits (G-cathodes) and grinding with silicon carbide emery paper (E-cathodes). The erosion rates of these cathodes were obtained by measuring the weight loss of the electrode after igniting as many as 135 arc pulses, each of which was 500 μs long at an arc current of 125 A. The erosion rates measured indicate that erosion rates decrease with decreasing roughness levels. Results obtained indicate that both surface roughness and surface patterns affect the erosion rate. Having patterns perpendicular to the direction of cathode spot movement gives lower erosion rates than having patterns parallel to arc movement. Isotropic surfaces give lower erosion rates than patterned surfaces at the same roughness

  6. Root surface smoothness or roughness following open debridement. An in vivo study.

    Science.gov (United States)

    Schlageter, L; Rateitschak-Plüss, E M; Schwarz, J P

    1996-05-01

    Consensus has not been reached on the desired characteristics of the root surface following cleaning. It is also not clear what degree of roughness or smoothness results from use of different instruments. In the present human clinical study, various instruments for root surface cleaning were evaluated. 18 teeth destined for extraction for periodontal reasons were utilized. After reflection of soft tissue flaps, the 72 root surface aspects of the 18 teeth were uniformally treated with one of the following instruments: Gracey curette (GC), piezo ultrasonic scaler (PUS), Perioplaner curette (PPC), sonic scaler (SS), 75 microns diamond (75 D) and 15 microns diamond (15.D). The degree of roughness of each surface was measured after extraction. A planimetry apparatus was used to establish the average surface roughness (Ra) and the mean depth of the roughness profile (Rz). It was demonstrated that hand- and machine-driven curettes as well as very fine rotating diamonds created the smoothest root surfaces, while "vibrating" instruments such as sonic and ultrasonic scalers, as well as coarse diamonds, tended to roughen the root surface. Whether the root surface should be rough or smooth in order to enhance tissue healing remains an open question.

  7. Sub ablative Er: YAG laser irradiation on surface roughness of eroded dental enamel.

    Science.gov (United States)

    Curylofo-Zotti, Fabiana Almeida; Lepri, Taísa Penazzo; Colucci, Vivian; Turssi, Cecília Pedroso; Corona, Silmara Aparecida Milori

    2015-11-01

    This study evaluated the effects of Er:YAG laser irradiation applied at varying pulse repetition rate on the surface roughness of eroded enamel. Bovine enamel slabs (n = 10) were embedded in polyester resin, ground, and polished. To erosive challenges, specimens were immersed two times per day in 20mL of concentrated orange juice (pH = 3.84) under agitation, during a two-day period. Specimens were randomly assigned to irradiation with the Er:YAG laser (focused mode, pulse energy of 60 mJ and energy density of 3.79 J/cm(2) ) operating at 1, 2, 3, or 4 Hz. The control group was left nonirradiated. Surface roughness measurements were recorded post erosion-like formation and further erosive episodes by a profilometer and observed through atomic force microscopy (AFM). Analysis of variance revealed that the control group showed the lowest surface roughness, while laser-irradiated substrates did not differ from each other following post erosion-like lesion formation. According to analysis of covariance, at further erosive episodes, the control group demonstrated lower surface roughness (P > 0.05), than any of the irradiated groups (P laser did not affect roughness of dental enamel eroded. The AFM images showed that the specimens irradiated by the Er:YAG laser at 1 Hz presented a less rough surface than those irradiated at 2, 3, and 4 Hz. © 2015 Wiley Periodicals, Inc.

  8. Influence of surface roughness on mechanical properties of two computer-aided design/computer-aided manufacturing (CAD/CAM) ceramic materials.

    Science.gov (United States)

    Flury, S; Peutzfeldt, A; Lussi, A

    2012-01-01

    The aim of this study was to evaluate the influence of surface roughness on surface hardness (Vickers; VHN), elastic modulus (EM), and flexural strength (FLS) of two computer-aided design/computer-aided manufacturing (CAD/CAM) ceramic materials. One hundred sixty-two samples of VITABLOCS Mark II (VMII) and 162 samples of IPS Empress CAD (IPS) were ground according to six standardized protocols producing decreasing surface roughnesses (n=27/group): grinding with 1) silicon carbide (SiC) paper #80, 2) SiC paper #120, 3) SiC paper #220, 4) SiC paper #320, 5) SiC paper #500, and 6) SiC paper #1000. Surface roughness (Ra/Rz) was measured with a surface roughness meter, VHN and EM with a hardness indentation device, and FLS with a three-point bending test. To test for a correlation between surface roughness (Ra/Rz) and VHN, EM, or FLS, Spearman rank correlation coefficients were calculated. The decrease in surface roughness led to an increase in VHN from (VMII/IPS; medians) 263.7/256.5 VHN to 646.8/601.5 VHN, an increase in EM from 45.4/41.0 GPa to 66.8/58.4 GPa, and an increase in FLS from 49.5/44.3 MPa to 73.0/97.2 MPa. For both ceramic materials, Spearman rank correlation coefficients showed a strong negative correlation between surface roughness (Ra/Rz) and VHN or EM and a moderate negative correlation between Ra/Rz and FLS. In conclusion, a decrease in surface roughness generally improved the mechanical properties of the CAD/CAM ceramic materials tested. However, FLS was less influenced by surface roughness than expected.

  9. Anisotropic wetting characteristics versus roughness on machined surfaces of hydrophilic and hydrophobic materials

    International Nuclear Information System (INIS)

    Liang, Yande; Shu, Liming; Natsu, Wataru; He, Fuben

    2015-01-01

    Graphical abstract: - Highlights: • The aim is to investigate the influence of roughness on anisotropic wetting on machined surfaces. • The relationship between roughness and anisotropic wetting is modeled by thermodynamical analysis. • The effect of roughness on anisotropic wetting on hydrophilic materials is stronger than that on hydrophobic materials. • The energy barrier existing in the direction perpendicular to the lay is one of the main reasons for the anisotropic wetting. • The contact angle in the parallel direction is larger than that in the perpendicular direction. - Abstract: Anisotropic wetting of machined surfaces is widely applied in industries which can be greatly affected by roughness and solid's chemical properties. However, there has not been much work on it. A free-energy thermodynamic model is presented by analyzing geometry morphology of machined surfaces (2-D model surfaces), which demonstrates the influence of roughness on anisotropic wetting. It can be concluded that the energy barrier is one of the main reasons for the anisotropic wetting existing in the direction perpendicular to the lay. In addition, experiments in investigating anisotropic wetting, which was characterized by the static contact angle and droplet's distortion, were performed on machined surfaces with different roughness on hydrophilic and hydrophobic materials. The droplet's anisotropy found on machined surfaces increased with mean slope of roughness profile Kr. It indicates that roughness on anisotropic wetting on hydrophilic materials has a stronger effect than that on hydrophobic materials. Furthermore, the contact angles predicted by the model are basically consistent with the experimentally ones

  10. Parallel optical trap assisted nanopatterning on rough surfaces

    International Nuclear Information System (INIS)

    Tsai, Y-C; Fardel, R; Arnold, C B; Leitz, K-H; Schmidt, M; Otto, A

    2012-01-01

    There exist many optical lithography techniques for generating nanostructures on hard, flat surfaces over large areas. However, few techniques are able to create such patterns on soft materials or surfaces with pre-existing structure. To address this need, we demonstrate the use of parallel optical trap assisted nanopatterning (OTAN) to provide an efficient and robust direct-write method of producing nanoscale features without the need for focal plane adjustment. Parallel patterning on model surfaces of polyimide with vertical steps greater than 1.5 µm shows a feature size uncertainty better than 4% across the step and lateral positional accuracy of 25 nm. A Brownian motion model is used to describe the positional accuracy enabling one to predict how variation in system parameters will affect the nanopatterning results. These combined results suggest that OTAN is a viable technique for massively parallel direct-write nanolithography on non-traditional surfaces. (paper)

  11. Stoichiometry-Induced Roughness on Antimonide Growth Surfaces

    National Research Council Canada - National Science Library

    Bracker, A. S; Nosho, B. Z; Barvosa-Carter, W; Whitman, L. J; Bennett, B. R; Shanabrook, B. V; Culbertson, J. C

    2001-01-01

    Phase shifts in the intensity oscillation of reflection high-energy electron diffraction spots provide evidence for monolayer island formation on AlSb that is caused by sudden changes in surface stoichiometry...

  12. Effect of acidic agents on surface roughness of dental ceramics

    Directory of Open Access Journals (Sweden)

    Boonlert Kukiattrakoon

    2011-01-01

    Conclusion: Acidic agents used in this study negatively affected the surface of ceramic materials. This should be considered when restoring the eroded tooth with ceramic restorations in patients who have a high risk of erosive conditions.

  13. Contact mechanics for layered materials with randomly rough surfaces.

    Science.gov (United States)

    Persson, B N J

    2012-03-07

    The contact mechanics model of Persson is applied to layered materials. We calculate the M function, which relates the surface stress to the surface displacement, for a layered material, where the top layer (thickness d) has different elastic properties than the semi-infinite solid below. Numerical results for the contact area as a function of the magnification are presented for several cases. As an application, we calculate the fluid leak rate for laminated rubber seals.

  14. Impact of roughness, wettability and hydrodynamic conditions on the incrustation on stainless steel surfaces

    International Nuclear Information System (INIS)

    Bogacz, Wojciech; Lemanowicz, Marcin; Al-Rashed, Mohsen H.; Nakonieczny, Damian; Piotrowski, Tomasz; Wójcik, Janusz

    2017-01-01

    Highlights: • Steel plates (X5CrNi18-10) with different roughness and wettability were prepared. • Incrustation of MgSO 4 ·7H 2 O under laminar flow (Re = 59–178) was investigated. • Influence of surface properties and fluid velocity on incrustation was found. • Wettability and surface roughness cannot be considered separately. • Analysis of heat transfer and incrustation time-lapse videos are presented. - Abstract: The goal of this work was to investigate the influence of the stainless steel surface roughness and wettability on incrustation of MgSO 4 ·7H 2 O from aqueous solutions and resulting heat transfer resistance. The experiments were done for laminar flow (Re = 59–178) which is characteristic for regions of apparatus where fouling usually begin. A series of steel plates (X5CrNi18-10) were prepared and used as a heat transfer surfaces. Their properties, i.e. roughness, wettability and elementary composition of surfaces were determined. The experiments were done using specially designed flow cell equipped with Peltier element. Each incrustation measurement lasted for two hours, during which heat transfer resistance was measured as a function of time. After the experiments the mass of crystalline deposit was weighted. It was proved that wettability as well as surface roughness cannot be considered separately in the case of incrustation phenomenon. The knowledge of surface roughness is insufficient due to the fact, that it is possible to obtain surfaces with similar roughness but substantially different wettability for the same material.

  15. Evaluation of a Regression Prediction Model for Surface Roughness of Wood-Polyethylene Composite (wpc)

    Science.gov (United States)

    Shi, Wenyong; Ma, Yan; Yang, Chunmei; Jiang, Bin; Li, Zhe

    Milling processing is an important way to obtain wood-polyethylene composite (WPC) end products. In order to improve the processing efficiency and surface quality of WPC and meet the practical application requirements, this paper focussed on morphology and roughness of the WPC-milled surface and studied surface quality changes under different cutting parameters and milling methods through multi-parameters milling experiments. The milling surface morphology and roughness of WPC were analyzed and measured during cut-in, cutting and cut-out sections. It also revealed the affect rule of different cutting parameters and milling methods on milled surface morphology and roughness. The results show that the milling surface roughness of WPC products with wood powder content of 70% is significantly larger than the one whose wood powder content is 60%, and defects such as holes are also relatively more. Finally, a surface roughness prediction model was established based on the mathematical regression method and its multi-factor simulation was carried out. A comparative analysis of predictive and experimental values was performed to verify the reliability of the model. It could also provide theoretical guidance and technical guarantee for high processing quality of WPC milling and cutting.

  16. Comparative investigation of optical techniques for topography measurement of rough plastic surfaces

    DEFF Research Database (Denmark)

    Bariani, Paolo; Hansen, Hans Nørgaard; Arlø, Uffe Rolf

    2003-01-01

    An experimental assessment of three-dimensional surface topography characterisation methods for use with rough plastic parts has been carried out. Also, calibration methods and measuring procedures including optimal measuring conditions have been developed and applied. The study is based on rough...... polypropylene parts manufactured by injection moulding. The mould was equipped with inserts with EDM machined surfaces (Sa  3.5 µm) in order to represent a typical tool surface for injection moulding. A focus detection laser scanning profiler, a confocal scanning laser microscope, a white light interferometer...... and, in addition, a scanning electron microscope, have been used in the analysis of plastic surfaces. This investigation has shown that topography assessment of rough plastic surfaces is critical to both white light interference microscope and confocal microscope while the focus detection laser...

  17. Analysis and optimisation of vertical surface roughness in micro selective laser melting

    International Nuclear Information System (INIS)

    Abele, Eberhard; Kniepkamp, Michael

    2015-01-01

    Surface roughness is a major disadvantage of many additive manufacturing technologies like selective laser melting (SLM) compared to established processes like milling or drilling. With recent advancements the resolution of the SLM process could be increased to layer heights of less than 10 μm leading to a new process called micro selective laser melting (μSLM). The purpose of this paper is to analyze the influence of the μSLM process parameters and exposure strategies on the morphology of vertical surfaces. Contour scanning using varying process parameters was used to increase the surface quality. It is shown that it is possible to achieve average surface roughness of less than 1.7 μm using low scan speeds compared to 8–10 μm without contour scanning. Furthermore it is shown that a contour exposure prior to the core exposure leads to surface defects and thus increased roughness. (paper)

  18. Effects of polishing on surface roughness, gloss, and color of resin composites.

    Science.gov (United States)

    Hosoya, Yumiko; Shiraishi, Takanobu; Odatsu, Tetsuro; Nagafuji, Junichi; Kotaku, Mayumi; Miyazaki, Masashi; Powers, John M

    2011-09-01

    This study evaluated the effects of polishing on surface roughness, gloss, and color of regular, opaque, and enamel shades for each of three resin composites. Two-mm-thick resin disks made with Estelite Σ Quick, Clearfil Majesty, and Beautifil II were final polished with 180-, 1000-, and 3000-grit silicon carbide paper. Surface roughness, gloss, and color were measured one week after curing. Estelite Σ Quick had significantly lower roughness values and significantly higher gloss values as compared with Clearfil Majesty and Beautifil II. The effects of surface roughness and gloss on color (L*a*b*) differed among resin composites and by shade. Correlation coefficients between surface roughness and L*a*b* color factors were generally high for Clearfil Majesty, partially high (i.e., between roughness and L*) for Beautifil II, and low for Estelite Σ Quick. Correlation coefficients between gloss and L*a*b* color parameters were generally high for Beautifil II and low for Estelite Σ Quick and Clearfil Majesty. However, for all resin composites, the values of the color differences between 3000-grit and 180-grit polishing groups for all shades were imperceptible by the naked eye.

  19. Photodesorption of Na atoms from rough Na surfaces

    DEFF Research Database (Denmark)

    Balzer, Frank; Gerlach, R.; Manson, J.R.

    1997-01-01

    We investigate the desorption of Na atoms from large Na clusters deposited on dielectric surfaces. High-resolution translational energy distributions of the desorbing atoms are determined by three independent methods, two-photon laser-induced fluorescence, as well as single-photon and resonance......-enhanced two-photon ionization techniques. Upon variation of surface temperature and for different substrates (mica vs lithium fluoride) clear non-Maxwellian time-of-flight distributions are observed with a cos θ angular dependence and most probable kinetic energies below that expected of atoms desorbing from...... atoms are scattered by surface vibrations. Recent experiments providing time constants for the decay of the optical excitations in the clusters support this model. The excellent agreement between experiment and theory indicates the importance of both absorption of the laser photons via direct excitation...

  20. Photodesorption of Na atoms from rough Na surfaces

    DEFF Research Database (Denmark)

    Balzer, Frank; Gerlach, R.; Manson, J.R.

    1997-01-01

    atoms are scattered by surface vibrations. Recent experiments providing time constants for the decay of the optical excitations in the clusters support this model. The excellent agreement between experiment and theory indicates the importance of both absorption of the laser photons via direct excitation......We investigate the desorption of Na atoms from large Na clusters deposited on dielectric surfaces. High-resolution translational energy distributions of the desorbing atoms are determined by three independent methods, two-photon laser-induced fluorescence, as well as single-photon and resonance......-enhanced two-photon ionization techniques. Upon variation of surface temperature and for different substrates (mica vs lithium fluoride) clear non-Maxwellian time-of-flight distributions are observed with a cos θ angular dependence and most probable kinetic energies below that expected of atoms desorbing from...

  1. Collisions of ideal gas molecules with a rough/fractal surface. A computational study.

    Science.gov (United States)

    Panczyk, Tomasz

    2007-02-01

    The frequency of collisions of ideal gas molecules (argon) with a rough surface has been studied. The rough/fractal surface was created using random deposition technique. By applying various depositions, the roughness of the surface was controlled and, as a measure of the irregularity, the fractal dimensions of the surfaces were determined. The surfaces were next immersed in argon (under pressures 2 x 10(3) to 2 x 10(5) Pa) and the numbers of collisions with these surfaces were counted. The calculations were carried out using a simplified molecular dynamics simulation technique (only hard core repulsions were assumed). As a result, it was stated that the frequency of collisions is a linear function of pressure for all fractal dimensions studied (D = 2, ..., 2.5). The frequency per unit pressure is quite complex function of the fractal dimension; however, the changes of that frequency with the fractal dimension are not strong. It was found that the frequency of collisions is controlled by the number of weakly folded sites on the surfaces and there is some mapping between the shape of adsorption energy distribution functions and this number of weakly folded sites. The results for the rough/fractal surfaces were compared with the prediction given by the Langmuir-Hertz equation (valid for smooth surface), generally the departure from the Langmuir-Hertz equation is not higher than 48% for the studied systems (i.e. for the surfaces created using the random deposition technique).

  2. Surface Roughness and Morphology Customization of Additive Manufactured Open Porous Ti6Al4V Structures

    Science.gov (United States)

    Pyka, Grzegorz; Kerckhofs, Greet; Papantoniou, Ioannis; Speirs, Mathew; Schrooten, Jan; Wevers, Martine

    2013-01-01

    Additive manufacturing (AM) is a production method that enables the building of porous structures with a controlled geometry. However, there is a limited control over the final surface of the product. Hence, complementary surface engineering strategies are needed. In this work, design of experiments (DoE) was used to customize post AM surface treatment for 3D selective laser melted Ti6Al4V open porous structures for bone tissue engineering. A two-level three-factor full factorial design was employed to assess the individual and interactive effects of the surface treatment duration and the concentration of the chemical etching solution on the final surface roughness and beam thickness of the treated porous structures. It was observed that the concentration of the surface treatment solution was the most important factor influencing roughness reduction. The designed beam thickness decreased the effectiveness of the surface treatment. In this case study, the optimized processing conditions for AM production and the post-AM surface treatment were defined based on the DoE output and were validated experimentally. This allowed the production of customized 3D porous structures with controlled surface roughness and overall morphological properties, which can assist in more controlled evaluation of the effect of surface roughness on various functional properties. PMID:28788357

  3. Surface Roughness and Morphology Customization of Additive Manufactured Open Porous Ti6Al4V Structures

    Directory of Open Access Journals (Sweden)

    Martine Wevers

    2013-10-01

    Full Text Available Additive manufacturing (AM is a production method that enables the building of porous structures with a controlled geometry. However, there is a limited control over the final surface of the product. Hence, complementary surface engineering strategies are needed. In this work, design of experiments (DoE was used to customize post AM surface treatment for 3D selective laser melted Ti6Al4V open porous structures for bone tissue engineering. A two-level three-factor full factorial design was employed to assess the individual and interactive effects of the surface treatment duration and the concentration of the chemical etching solution on the final surface roughness and beam thickness of the treated porous structures. It was observed that the concentration of the surface treatment solution was the most important factor influencing roughness reduction. The designed beam thickness decreased the effectiveness of the surface treatment. In this case study, the optimized processing conditions for AM production and the post-AM surface treatment were defined based on the DoE output and were validated experimentally. This allowed the production of customized 3D porous structures with controlled surface roughness and overall morphological properties, which can assist in more controlled evaluation of the effect of surface roughness on various functional properties.

  4. Light transmittance and surface roughness of a feldspathic ceramic CAD-CAM material as a function of different surface treatments.

    Science.gov (United States)

    Ural, Çağrı; Duran, İbrahim; Evmek, Betül; Kavut, İdris; Cengiz, Seda; Yuzbasioglu, Emir

    2016-07-15

    The aim of the present study was to determine the effect of different surface treatments on light transmission of aesthetic feldspathic ceramics used in CAD-CAM chairside restorations. Forty eight feldspatic ceramic test specimens were prepared from prefabricated CAD-CAM blocks by using a slow speed diamond saw. Test specimens were prepared and divided into 4 groups (n = 12). In the control group, no surface treatments were applied on the feldspathic ceramic surfaces. In the hydrofluoric acid group, the bonding surfaces of feldspathic ceramics were etched with 9.5 % hydrofluoric acid. In the sandblasting group the feldspathic ceramic surfaces were air-abraded with 30-μm alumium oxide (Al2O3) particles and Er:YAG laser was used to irradiate the ceramic surfaces. The incident light power given by the LED device and the transmitted light power through each ceramic sample was registered using a digital LED radiometer device. Each polymerization light had a light guide with 8-mm-diameter tips. Light transmission of feldspathic ceramic samples was determined by placing it on the radiometer and irradiating the specimen for 10 s at the highest setting for each light polymerization. All specimens were coated with gold using a sputter coater and examined under a field emission scanning electron microscope. Surface roughness measurement each group were evaluated with 3D optical surface and tactile profilometers. One-way ANOVA test results revealed that both surface conditioning method significantly affect the light transmittance (F:412.437; p ceramic material below the value of 400 mW/cm(2) which is critical limit for safe polymerization.

  5. Empirical model for estimating the surface roughness of machined ...

    African Journals Online (AJOL)

    The increasing importance of turning operations is gaining new dimensions in the present industrial age, in which the growing competition calls for all the efforts to be directed towards the economical manufacture of machined parts as well as surface finish is one of the most critical quality measure in mechanical products.

  6. Tribological influence of tool surface roughness within microforming

    DEFF Research Database (Denmark)

    Eriksen, Rasmus Solmer; Weidel, S.; Hansen, Hans Nørgaard

    2010-01-01

    A comparative friction study of tooling dies with a simple internal cylindrical geometry has been performed. The purpose of the experiment consist of studying the influence of the surface characteristics of tooling dies on the frictional behaviour in a micro bulk forming operation. This research ...

  7. Surface roughness and morphologic changes of zirconia: Effect of ...

    African Journals Online (AJOL)

    10 MPa m1/2), high biocompatibility and natural appearance. ... perpendicularly to the surface at 10 mm distance and was moved in a sweeping fashion by hand during an exposure period of 20 s over the entire area. The energy parameters.

  8. The Contribution of Antimonide Surface Reconstructions to Heterostructure Interface Roughness

    National Research Council Canada - National Science Library

    Bracker, A. S; Barvosa-Carter, W; Culbertson, J. C; Nosho, B. Z; Whitman, L. J; Shanabrook, B. V; Bennett, B. R; Yang, M. J

    1999-01-01

    ... for the 6.1 Angstrom family of compound semiconductors (InAs, GaSb, AlSb). The structure and stoichiometry of MBE-grown antimonide surfaces lead to growth and roughening mechanisms that are distinctly different from other III-V materials...

  9. Factors Affecting Optimal Surface Roughness of AISI 4140 Steel in Turning Operation Using Taguchi Experiment

    Science.gov (United States)

    Novareza, O.; Sulistiyarini, D. H.; Wiradmoko, R.

    2018-02-01

    This paper presents the result of using Taguchi method in turning process of medium carbon steel of AISI 4140. The primary concern is to find the optimal surface roughness after turning process. The taguchi method is used to get a combination of factors and factor levels in order to get the optimum surface roughness level. Four important factors with three levels were used in experiment based on Taguchi method. A number of 27 experiments were carried out during the research and analysed using analysis of variance (ANOVA) method. The result of surface finish was determined in Ra type surface roughness. The depth of cut was found to be the most important factors for reducing the surface roughness of AISI 4140 steel. On the contrary, the other important factors i.e. spindle speed and rake side angle of the tool were proven to be less factors that affecting the surface finish. It is interesting to see the effect of coolant composition that gained the second important factors to reduce the roughness. It may need further research to explain this result.

  10. In processing of a spheroidized medium carbon steel, modelling with regression analysis of cutting forces and surface roughness affected by cutting parameters

    Directory of Open Access Journals (Sweden)

    Hüdayim Başak

    2016-08-01

    Full Text Available In this study, different spheronization heat treatment applied on a mild carbon steel during the machining was created main cutting forces and surface roughness value, were modeled by using multiple linear regression analysis. Main cutting force and surface roughness value which are dependent variable are described respectively rate of 94.6% and 94.2% by independent variables. The ANOVA significance test were used to determine dependent and independent variables correlations. Also, processing parameters variations such as effects on the feed rate, depth of cut and cutting force changes effect on surface roughness and main cutting force general effects were plotted to discuss.

  11. Surface roughness effect on ultracold neutron interaction with a wall and implications for computer simulations

    OpenAIRE

    Steyerl, A.; Malik, S. S.; Desai, A. M.; Kaufman, C.

    2009-01-01

    We review the diffuse scattering and the loss coefficient in ultracold neutron reflection from slightly rough surfaces, report a surprising reduction in loss coefficient due to roughness, and discuss the possibility of transition from quantum treatment to ray optics. The results are used in a computer simulation of neutron storage in a recent neutron lifetime experiment that re-ported a large discrepancy of neutron lifetime with the current particle data value. Our partial re-analysis suggest...

  12. The influence of surface roughness on supersonic high Reynolds number turbulent boundary layer flow

    Science.gov (United States)

    Latin, Robert Michael

    A comprehensive study of rough-wall high-speed (M = 2.9) high Reynolds number (Re/m = 1.9e7) turbulent boundary layer flow was performed consisting of experimental, analytical, and numerical methods. Six wall topologies consisting of a smooth and five rough surfaces (two- and three-dimensional machined roughness plates; and 80, 36. and 20 grit sand-grain roughened plates) were studied. A confocal laser scan microscope was used to measure the topography of the sand-grain roughnesses. The experimental measurement techniques included a convention Pitot pressure probe, laser Doppler velocimetry, hot-wire anemometry, color schlieren and laser sheet Mie scattering images. Mean measurements included velocity, Mach number, density, and mass flux. Turbulent measurements included velocity and mass flux turbulence intensities, kinematic Reynolds shear stress, compressible Reynolds shear stress in two planes, and the traverse apparent mass flux. Kinematic turbulent flow statistical properties were found to scale by local mean quantities and displayed a weak dependence on surface roughness. Turbulent flow statistical properties with the explicit appearance of density did not scale by local mean quantities, and had a strong linear dependence on roughness. Surface roughness also had a significant effect on the flow structure size, angles, and energy spectra. A theoretical analysis was performed and a new integral method for the estimation of skin friction was developed. The skin friction estimates were within 4% of compressible semi-empirical relations. A numerical study was performed which used a parabolized Navier-Stokes solver with two algebraic turbulence models and the Rotta model for surface roughness. A new method for the estimation of momentum loss improved the numerical flow predictability. The algebraic turbulence models predicted qualitatively correct profile shapes and accurately predicted the kinematic and compressible Reynolds shear stress levels for all but the

  13. Solid-solid contacts due to surface roughness and their effects on suspension behaviour.

    Science.gov (United States)

    Davis, Robert H; Zhao, Yu; Galvin, Kevin P; Wilson, Helen J

    2003-05-15

    Solid-solid contacts due to microscopic surface roughness in viscous fluids were examined by observing the translational and rotational behaviours of a suspended sphere falling past a lighter sphere or down an inclined surface. In both cases, a roll-slip behaviour was observed, with the gravitational forces balanced by not only hydrodynamic forces but also normal and tangential solid-solid contact forces. Moreover, the nominal separation between the surfaces due to microscopic surface roughness elements is not constant but instead varies due to multiple roughness scales. By inverting the system, so that the heavy sphere fell away from the lighter sphere or the plane, it was found that the average nominal separation increases with increasing angle of inclination of the plane or the surface of the lighter sphere from horizontal; the larger asperities lift the sphere up from the opposing surface and then gravity at large angles of inclination is too weak to pull the sphere back down to the opposing surface before another large asperity is encountered. The existence of microscopic surface roughness and solid-solid contacts is shown to modify the rheological properties of suspensions. For example, the presence of compressive, but not tensile, contact forces removes the reversibility of sphere-sphere interactions and breaks the symmetry of the particle trajectories. As a result, suspensions of rough spheres exhibit normal stress differences that are absent for smooth spheres. For the conditions studied, surface roughness reduces the effective viscosity of a suspension by limiting the lubrication resistance during near-contact motion, and it also modifies the suspension microstructure and hydrodynamic diffusivity.

  14. The Effects of Surface Roughness on the Apparent Thermal and Optical Properties of the Moon

    Science.gov (United States)

    Rubanenko, L.; Hayne, P. O.; Paige, D. A.

    2017-12-01

    The thermal inertia and albedo of airless planetary bodies such as the Moon can be inferred by measuring the surface temperatures and solar reflectance. However, roughness below the instrument resolution can affect these measured parameters. Scattering and IR emission from warm slopes onto colder slopes change the surface cooling rate, while shadowing and directional scattering change the reflectance. The importance of these effects grows with increasing solar incidence and emission angles, and during solar eclipses during which the insolation decreases rapidly. The high-quality data gathered by the Lunar Reconnaissance Orbiter (LRO) mission during the last seven years provides us with a unique opportunity to study these effects. Previous works have either adopted a simplified roughness model composed of a single slope, or an illumination model that does not account for subsurface conduction. Our approach incorporates data with simulations conducted using a coupled thermal and illumination model. First, we model the surface temperature distribution below the instrument resolution, considering two realizations: a cratered surface and a Gaussian random surface. Then, we fit the rough surface brightness temperature distribution to that of a flat surface with effective thermal and optical properties to find they differ from the original properties by up to 20% due to the added surface roughness. In the future, this will help to better constrain the intrinsic physical properties of the surface on both the Moon and Mercury and also other airless bodies such as asteroids.

  15. Cell adhesion on Ti surface with controlled roughness

    Energy Technology Data Exchange (ETDEWEB)

    Burgos-Asperilla, L.; Garcia-Alonso, M. C.; Escudero, M. L.; Alonso, C.

    2015-07-01

    In this report, the in situ interaction between Saos-2 osteoblast cells and a smooth Ti surface was examined over time. The adhesion kinetics and mechanisms of cellular proliferation were monitored by quartz crystal microbalance (QCM) and electrochemical impedance spectroscopy (EIS). The rate of Saos-2 attachment on Ti surfaces, obtained from the measurements performed with the QCM, is a first-order reaction, with k=2.10{sup -}3 min{sup -}1. The impedance measurements indicate that in the absence of cells, the Ti resistance diminishes over time (7 days), due to the presence of amino acids and proteins from the culture medium that have been adsorbed, while in the presence of osteoblasts, this decrease is much greater because of the compounds generated by the cells that accelerate the dissolution of Ti. (Author)

  16. EFFECT OF SOIL TILLAGE AND PLANT RESIDUE ON SURFACE ROUGHNESS OF AN OXISOL UNDER SIMULATED RAIN

    Directory of Open Access Journals (Sweden)

    Elói Panachuki

    2015-02-01

    Full Text Available Surface roughness of the soil is formed by mechanical tillage and is also influenced by the kind and amount of plant residue, among other factors. Its persistence over time mainly depends on the fundamental characteristics of rain and soil type. However, few studies have been developed to evaluate these factors in Latossolos (Oxisols. In this study, we evaluated the effect of soil tillage and of amounts of plant residue on surface roughness of an Oxisol under simulated rain. Treatments consisted of the combination of the tillage systems of no-tillage (NT, conventional tillage (CT, and minimum tillage (MT with rates of plant residue of 0, 1, and 2 Mg ha-1 of oats (Avena strigosa Schreb and 0, 3, and 6 Mg ha-1 of maize (Zea mays L.. Seven simulated rains were applied on each experimental plot, with intensity of 60±2 mm h-1 and duration of 1 h at weekly intervals. The values of the random roughness index ranged from 2.94 to 17.71 mm in oats, and from 5.91 to 20.37 mm in maize, showing that CT and MT are effective in increasing soil surface roughness. It was seen that soil tillage operations carried out with the chisel plow and the leveling disk harrow are more effective in increasing soil roughness than those carried out with the heavy disk harrow and leveling disk harrow. The roughness index of the soil surface decreases exponentially with the increase in the rainfall volume applied under conditions of no tillage without soil cover, conventional tillage, and minimum tillage. The oat and maize crop residue present on the soil surface is effective in maintaining the roughness of the soil surface under no-tillage.

  17. Novel CNC Grinding Process Control for Nanometric Surface Roughness for Aspheric Space Optical Surfaces

    Directory of Open Access Journals (Sweden)

    Jeong-Yeol Han

    2004-06-01

    Full Text Available Optics fabrication process for precision space optical parts includes bound abrasive grinding, loose abrasive lapping and polishing. The traditional bound abrasive grinding with bronze bond cupped diamond wheel leaves the machine marks of about 20 μm rms in height and the subsurface damage of about 1 μm rms in height to be removed by subsequent loose abrasive lapping. We explored an efficient quantitative control of precision CNC grinding. The machining parameters such as grain size, work-piece rotation speed and feed rate were altered while grinding the work-piece surfaces of 20-100 mm in diameter. The input grinding variables and the resulting surface quality data were used to build grinding prediction models using empirical and multi-variable regression analysis. The effectiveness of such grinding prediction models was then examined by running a series of precision CNC grinding operation with a set of controlled input variables and predicted output surface quality indicators. The experiment achieved the predictability down to ±20 nm in height and the surface roughness down to 36 nm in height. This study contributed to improvement of the process efficiency reaching directly the polishing and figuring process without the need for the loose abrasive lapping stage.

  18. Influence of Sea Surface Roughness on the Electromagnetic Wave Propagation in the Duct Environment

    Directory of Open Access Journals (Sweden)

    X. Zhao

    2010-12-01

    Full Text Available This paper deals with a study of the influence of sea surface roughness on the electromagnetic wave propagation in the duct environment. The problem of electromagnetic wave propagation is modeled by using the parabolic equation method. The roughness of the sea surface is computed by modifying the smooth surface Fresnel reflection coefficient to account for the reduction in the specular reflection due to the roughness resulting from sea wind speed. The propagation model is solved by the mixed Fourier split-step algorithm. Numerical experiments indicate that wind-driven roughened sea surface has an impact on the electromagnetic wave propagation in the duct environment, and the strength is intensified along with the increment of sea wind speeds and/or the operating frequencies. In a fixed duct environment, however, proper disposition of the transmitter could reduce these impacts.

  19. Rough surface electrical contact resistance considering scale dependent properties and quantum effects

    International Nuclear Information System (INIS)

    Jackson, Robert L.; Crandall, Erika R.; Bozack, Michael J.

    2015-01-01

    The objective of this work is to evaluate the effect of scale dependent mechanical and electrical properties on electrical contact resistance (ECR) between rough surfaces. This work attempts to build on existing ECR models that neglect potentially important quantum- and size-dependent contact and electrical conduction mechanisms present due to the asperity sizes on typical surfaces. The electrical conductance at small scales can quantize or show a stepping trend as the contact area is varied in the range of the free electron Fermi wavelength squared. This work then evaluates if these effects remain important for the interface between rough surfaces, which may include many small scale contacts of varying sizes. The results suggest that these effects may be significant in some cases, while insignificant for others. It depends on the load and the multiscale structure of the surface roughness

  20. Effect of diameter and surface roughness on ultrasonic properties of GaAs nanowires

    Science.gov (United States)

    Dhawan, Punit Kumar; Wan, Meher; Verma, S. K.; Pandey, D. K.; Yadav, R. R.

    2015-02-01

    Second and third order elastic constants of GaAs Nanowires (NWs) are calculated using the many-body interaction potential model. The velocities of ultrasonic waves at different orientations of propagation with unique axis are evaluated using the second order elastic constants. The ultrasonic attenuation and thermal relaxation times of the single crystalline GaAs-NW are determined as a function of diameter and surface roughness by means of Mason theoretical approach using the thermal conductivity and higher order elastic constants. The diameter variation of ultrasonic attenuation and thermal relaxation exhibit second order polynomial function of diameter. It is also found that ultrasonic attenuation and thermal relaxation follow the exponential decay with the surface roughness for GaAs-NW due to reduction in thermal conductivity caused by dominance of surface asperities. Finally, the correlations among ultrasonic parameters, thermal conductivity, surface roughness, and diameter for GaAs-NWs are established leading towards potential applications.

  1. An in vitro investigation to compare the surface roughness of auto glazed, reglazed and chair side polished surfaces of Ivoclar and Vita feldspathic porcelain.

    Science.gov (United States)

    Sethi, Sumit; Kakade, Dilip; Jambhekar, Shantanu; Jain, Vinay

    2013-12-01

    The change in surface roughness after different surface finishing techniques has attracted the attention of several prosthodontists regarding wear of opposing teeth or restorative material and the strength; plaque retention and appearance of the restoration. However, there is considerable controversy concerning the best methods to achieve the smoothest and strongest porcelain restorations after chair side clinical adjustments. The purpose of this in vitro study was to compare the average surface roughness of a self-glazed surface, a chair side polished surface and a reglazed surface of ceramic. Two feldspathic porcelain, namely VITA VMK94 (Vita Zahnfabrik, Bad Sachingen, Germany) and IVOCLAR CLASSIC (Vivadent AG, FL-9494 Schaan, Liechtenstein) were selected to fabricate 20 specimens of each in the shape of shade guide tabs. A medium-grit diamond rotary cutting instrument was used to remove the glaze layer, and then the surface of half the specimens were re-glazed and the other half were polished using a well-defined sequence of polishing comprising of: Shofu porcelain polishing system, White gloss disc/polishing wheel, Silicone cone with diamond polishing paste and finally with small buff wheel with pumice slurry. The surface roughness (Ra) (μm) of the specimens was evaluated using a profilometer and scanning electron microscope. The data were statistically analyzed by using Student's t test. The results had shown that there is no statistically significant difference both quantitatively and qualitatively, between the surface roughness of reglazed and chair-side polished surface. In addition, both reglazed and chair-side polished surfaces are better than the autoglazed surface. Within all the groups, there is no significant difference between companies. Polishing an adjusted porcelain surface with the suggested sequence of polishing will lead to a finish similar to a re-glazed surface. Therefore chair-side polishing can be a good alternative to reglazing for

  2. 4He adsorption and third-sound propagation on rough CaF2 surfaces

    International Nuclear Information System (INIS)

    Herrmann, J.C.; Hallock, R.B.

    2003-01-01

    We have investigated the propagation of third sound on well characterized rough CaF 2 surfaces as a function of 4 He film thickness. In addition we have measured the adsorption of 4 He to the CaF 2 surfaces using quartz crystal microbalances. We report values for the superfluid depletion thickness D for the three surfaces examined here. A model for the reduction of the third-sound speed due to the increased helium adsorption on rough CaF 2 is explored

  3. Linear systems formulation of scattering theory for rough surfaces with arbitrary incident and scattering angles.

    Science.gov (United States)

    Krywonos, Andrey; Harvey, James E; Choi, Narak

    2011-06-01

    Scattering effects from microtopographic surface roughness are merely nonparaxial diffraction phenomena resulting from random phase variations in the reflected or transmitted wavefront. Rayleigh-Rice, Beckmann-Kirchhoff. or Harvey-Shack surface scatter theories are commonly used to predict surface scatter effects. Smooth-surface and/or paraxial approximations have severely limited the range of applicability of each of the above theoretical treatments. A recent linear systems formulation of nonparaxial scalar diffraction theory applied to surface scatter phenomena resulted first in an empirically modified Beckmann-Kirchhoff surface scatter model, then a generalized Harvey-Shack theory that produces accurate results for rougher surfaces than the Rayleigh-Rice theory and for larger incident and scattered angles than the classical Beckmann-Kirchhoff and the original Harvey-Shack theories. These new developments simplify the analysis and understanding of nonintuitive scattering behavior from rough surfaces illuminated at arbitrary incident angles.

  4. Non-Contact Surface Roughness Measurement by Implementation of a Spatial Light Modulator.

    Science.gov (United States)

    Aulbach, Laura; Salazar Bloise, Félix; Lu, Min; Koch, Alexander W

    2017-03-15

    The surface structure, especially the roughness, has a significant influence on numerous parameters, such as friction and wear, and therefore estimates the quality of technical systems. In the last decades, a broad variety of surface roughness measurement methods were developed. A destructive measurement procedure or the lack of feasibility of online monitoring are the crucial drawbacks of most of these methods. This article proposes a new non-contact method for measuring the surface roughness that is straightforward to implement and easy to extend to online monitoring processes. The key element is a liquid-crystal-based spatial light modulator, integrated in an interferometric setup. By varying the imprinted phase of the modulator, a correlation between the imprinted phase and the fringe visibility of an interferogram is measured, and the surface roughness can be derived. This paper presents the theoretical approach of the method and first simulation and experimental results for a set of surface roughnesses. The experimental results are compared with values obtained by an atomic force microscope and a stylus profiler.

  5. Improvement of surface roughness in silicon-on-insulator wafer fabrication using a neutral beam etching

    Science.gov (United States)

    Min, T. H.; Park, B. J.; Kang, S. K.; Gweon, G. H.; Kim, Y. Y.; Yeom, G. Y.

    2009-08-01

    Silicon-on-insulator (SOI) wafers were etched by an energetic chlorine neutral beam obtained by the low-angle forward reflection of an ion beam, and the surface roughness of the etched wafers was compared with that of the SOI wafers etched by an energetic chlorine ion beam. When the ion beam was used to etch the silicon layer of the SOI wafers, the surface roughness was not significantly changed even though the use of higher ion bombardment energy slightly decreased the surface roughness of the SOI wafer. However, when the chlorine neutral beam was used instead of the chlorine ion beam having a similar beam energy, the surface roughness of the SOI wafer was significantly improved compared with that etched by the chlorine ion beam. By etching about 150 nm silicon from the SOI wafer having a 300 nm-thick top silicon layer with the chlorine neutral beam at the energy of 500 eV, the rms surface roughness of 1.5 Å could be obtained with the etch rate of about 750 Å min-1.

  6. Mesoscopic surface roughness of ice crystals pervasive across a wide range of ice crystal conditions

    Science.gov (United States)

    Magee, N. B.; Miller, A.; Amaral, M.; Cumiskey, A.

    2014-11-01

    Here we show high-magnification images of hexagonal ice crystals acquired by environmental scanning electron microscopy (ESEM). Most ice crystals were grown and sublimated in the water vapor environment of an FEI-Quanta-200 ESEM, but crystals grown in a laboratory diffusion chamber were also transferred intact and imaged via ESEM. All of these images display prominent mesoscopic topography including linear striations, ridges, islands, steps, peaks, pits, and crevasses; the roughness is not observed to be confined to prism facets. The observations represent the most highly magnified images of ice surfaces yet reported and expand the range of conditions in which rough surface features are known to be conspicuous. Microscale surface topography is seen to be ubiquitously present at temperatures ranging from -10 °C to -40 °C, in supersaturated and subsaturated conditions, on all crystal facets, and irrespective of substrate. Despite the constant presence of surface roughness, the patterns of roughness are observed to be dramatically different between growing and sublimating crystals, and transferred crystals also display qualitatively different patterns of roughness. Crystals are also demonstrated to sometimes exhibit inhibited growth in moderately supersaturated conditions following exposure to near-equilibrium conditions, a phenomenon interpreted as evidence of 2-D nucleation. New knowledge about the characteristics of these features could affect the fundamental understanding of ice surfaces and their physical parameterization in the context of satellite retrievals and cloud modeling. Links to supplemental videos of ice growth and sublimation are provided.

  7. Comparison of different polishing methods on the surface roughness of microhybrid, microfill, and nanofill composite resins.

    Science.gov (United States)

    Moda, Mariana D; Godas, André Gustavo de L; Fernandes, Juliana C; Suzuki, Thaís Y U; Guedes, Ana Paula A; Briso, André L F; Bedran-Russo, Ana Karina; Dos Santos, Paulo H

    2018-02-01

    The aim of the present study was to evaluate the effect of different polishing methods on the surface roughness of resin-based composites subjected to a thermocycling procedure. A total of 192 specimens were divided into 24 groups, according to composite materials (Filtek Z250, Point 4, Renamel Nanofill, Filtek Supreme Plus, Renamel Microfill, and Premise) and finishing and polishing systems (Sof-Lex Pop On, Super Snap, Flexidisc, and Flexidisc+Enamelize). The specimens were subjected to thermocycling (5000 cycles). Filtek Supreme Plus showed the lowest surface roughness values before thermocycling. After thermocycling, Filtek Supreme Plus continued to have the lowest surface roughness, with a statistically-significant difference for the other materials. After thermocycling, there was no statistically-significant difference among all the polishing techniques studied. The thermocycling was concluded as being able to change composite resins' surface roughness, whereas different finishing and polishing methods did not result in surface roughness changes after thermocycling. © 2017 John Wiley & Sons Australia, Ltd.

  8. Influence of surface roughness of stainless steel on microbial adhesion and corrosion resistance

    DEFF Research Database (Denmark)

    Hilbert, Lisbeth Rischel; Bagge-Ravn, Dorthe; Kold, John

    2003-01-01

    was evaluated in a commercial disinfectant and in 1 M NaCl. Electropolished and grit 4000 polished steel proved more corrosion resistant as opposed to grit 80 and 120 polished surfaces. In conclusion, the surface finish did not influence bacterial attachment, colonisation, or removal, but is an important...... was not affected by surface roughness (Ra) ranging from grit 4000 polished stainless steel (Ra resistance...... parameter for the corrosion resistance of the surface....

  9. Surface roughness prediction model in end milling of Al/SiC p MMC ...

    African Journals Online (AJOL)

    This research focuses on study and analyses of surface quality improvement in end milling operation of Al/SiCp metal matrix composite. These materials are selected as they are most widely used in automobile and aerospace industry. This research paper develops an improved mathematical model for surface roughness ...

  10. Parameterization of rain induced surface roughness and its validation study using a third generation wave model

    Science.gov (United States)

    Rajesh Kumar, R.; Prasad Kumar, B.; Bala Subrahamanyam, D.

    2009-09-01

    The effect of raindrops striking water surface and their role in modifying the prevailing sea-surface roughness is investigated. The work presents a new theoretical formulation developed to study rain-induced stress on sea-surface based on dimensional analysis. Rain parameters include drop size, rain intensity and rain duration. The influences of these rain parameters on young and mature waves were studied separately under varying wind speeds, rain intensity and rain duration. Contrary to popular belief that rain only attenuates surface waves, this study also points out rain duration under certain condition can contribute to wave growth at high wind speeds. Strong winds in conjunction with high rain intensity enhance the horizontal stress component on the sea-surface, leading to wave growth. Previous studies based on laboratory experiments and dimensional analysis do not account for rain duration when attempting to parameterize sea-surface roughness. This study signifies the importance of rain duration as an important parameter modifying sea-surface roughness. Qualitative as well quantitative support for the developed formulation is established through critical validation with reports of several researchers and satellite measurements for an extreme cyclonic event in the Indian Ocean. Based on skill assessment, it is suggested that the present formulation is superior to prior studies. Numerical experiments and validation performed by incorporating in state-of-art WAM wave model show the importance of treating rain-induced surface roughness as an essential pre-requisite for ocean wave modeling studies.

  11. Efficacy of polishing kits on the surface roughness and color stability ...

    African Journals Online (AJOL)

    Objective: Different polishing kits may have different effects on the composite resin surfaces. The aim of this study was to evaluate the surface roughness and color stability of four different composites which was applied different polishing technique. Materials and Methods: Thirty specimens were made for each composite ...

  12. Surface-Roughness-Based Virtual Textiles: Evaluation Using a Multi-Contactor Display.

    Science.gov (United States)

    Philpott, Matthew; Summers, Ian R

    2015-01-01

    Virtual textiles, generated in response to exploratory movements, are presented to the fingertip via a 24-contactor vibrotactile array. Software models are based on surface-roughness profiles from real textiles. Results suggest that distinguishable "textile-like" surfaces are produced, but these lack the necessary accuracy for reliable matching to real textiles.

  13. Effective aerodynamic roughness estimated from airborne laser altimeter measurements of surface features

    NARCIS (Netherlands)

    De Vries, AC; Kustas, WP; Ritchie, JC; Klaassen, W; Menenti, M; Rango, A; Prueger, JH

    2003-01-01

    Aerodynamic roughness length (z(0)) and displacement height (d(0)) are important surface parameters for estimating surface fluxes in numerical models. These parameters are generally determined from wind flow characteristics using logarithmic wind profiles measured at a meteorological tower or by

  14. A numerical assessment of rough surface scattering theories. I - Horizontal polarization. II - Vertical polarization

    Science.gov (United States)

    Rodriguez, Ernesto; Kim, Yunjin; Durden, Stephen L.

    1992-01-01

    A numerical evaluation is presented of the regime of validity for various rough surface scattering theories against numerical results obtained by employing the method of moments. The contribution of each theory is considered up to second order in the perturbation expansion for the surface current. Considering both vertical and horizontal polarizations, the unified perturbation method provides best results among all theories weighed.

  15. Surface roughness prediction model in end milling of Al/SiCp MMC ...

    African Journals Online (AJOL)

    user

    Keywords: Surface roughness (Ra), Response surface method (RSM), End milling, Metal matrix composites. DOI: http://dx.doi.org/10.4314/ijest.v3i6.7. 1. Introduction. The recent advancements in the CNC machine tool technology and the wide availability in manufacturing of mechanical components made it possible to ...

  16. Effect of alloy type and surface conditioning on roughness and bond strength of metal brackets

    NARCIS (Netherlands)

    Nergiz, I.; Schmage, P.; Herrmann, W.; Ozcan, M.; Nergiz, [No Value

    2004-01-01

    The effect of 5 different surface conditioning methods on bonding of metal brackets to cast dental alloys was examined. The surface conditioning methods were fine (30-µm) or rough (125-µm) diamond bur, sandblasting (50-µm or 110-µm aluminum oxide [Al2O3]), and silica coating (30-µm silica). Fifty

  17. On the dependence of sea surface roughness on wind waves

    DEFF Research Database (Denmark)

    Johnson, H.K.; Højstrup, J.; Vested, H.J.

    1998-01-01

    The influence of wind waves on the momentum transfer (wind stress) between the atmosphere and sea surface was studied using new measured data from the RASEX experiment and other datasets compiled by Donelan et al. Results of the data analysis indicate that errors in wind friction velocity u...... that calculations of the wind friction velocities using the wave-spectra-dependent expression of Hansen and Larsen agrees quite well with measured values during RASEX. It also gives a trend in Charnock parameter consistent with that found by combining the field data. Last, calculations using a constant Charnock...... parameter (0.018) also give very good results for the wind friction velocities at the RASEX site....

  18. Parameterization of albedo, thermal inertia, and surface roughness of desert scrub/sandy soil surface

    Science.gov (United States)

    Otterman, J.; Mccumber, M.

    1986-01-01

    Spectral albedo, A sub n, for the direct solar beam is defined as A sub n (r sub i,s, theta sub 0) = r sub i exp(-s tan theta sub 0)1-I(s) where I(s) is the integral over all reflection angles describing the interception by the absorbing plants of the flux reflected from the soil, r sub i soil reflectance, assumed Lambertian, S the projection on a vertical plane of plants per unit surface area, and theta sub 0 is the solar zenith angle. Hemispheric reflectance for the direct solar beam equals 1-I(s) times the reflectance to the zenith. The values of s of 0.1, 0.2, and 0.3 respectively quantify sparse, moderately dense, and very dense desert scrub. Thin plants are assumed to be of negligible thermal inertia, and thus directly yield the absorbed insolation to the atmosphere. Surface thermal inertia is therefore effectively reduced. The ratio of surface roughness height to plant height is parameterized for sparse, moderately dense, and very dense desert-scrub as a function of s based on data expressing the dependence of this ratio on plant silhouette.

  19. Surface roughness of polyvinyl siloxane impression materials following chemical disinfection, autoclave and microwave sterilization.

    Science.gov (United States)

    Al Kheraif, Abdulaziz Abdullah

    2013-05-01

    Autoclave sterilization and microwave sterilization has been suggested as the effective methods for the disinfection of elastomeric impressions, but subjecting elastomeric impressions to extreme temperature may have adverse effects on critical properties of the elastomers. To evaluate the effect of chemical disinfection as well as autoclave and microwave sterilization on the surface roughness of elastomeric impression materials. The surface roughness of five commercially available polyvinyl siloxane impression materials (Coltene President, Affinis Perfect impression, Aquasil, 3M ESPE Express and GC Exafast) were evaluated after subjecting them to chemical disinfection, autoclaving and microwave sterilization using a Talysurf Intra 50 instrument. Twenty specimens from each material were fabricated and divided into four equal groups, three experimental and one control (n=25). The differences in the mean surface roughness between the treatment groups were recorded and statistically analyzed. No statistically significant increase in the surface roughness was observed when the specimens were subjected to chemical disinfection and autoclave sterilization, increase in roughness and discoloration was observed in all the materials when specimens were subjected to microwave sterilization. Chemical disinfection did not have a significant effect but, since it is less effective, autoclave sterilization can be considered effective and autoclaving did not show any specimen discoloration as in microwave sterilization. Microwave sterilization may be considered when impressions are used to make diagnostic casts. A significant increase in surface roughness may produce rougher casts, resulting in rougher tissue surfaces for denture and cast restorations. Autoclave sterilization of vinyl polysiloxane elastomeric impressions for 5 minutes at 134°C at 20 psi may be considered an effective method over chemical disinfection and microwave sterilization, because chemical disinfection does

  20. Influence of Cooling Lubricants on the Surface Roughness and Energy Efficiency of the Cutting Machine Tools

    Science.gov (United States)

    Jersák, J.; Simon, S.

    2017-08-01

    The Technical University of Liberec and Brandenburg University of Technology Cottbus-Senftenberg investigated the influence of cooling lubricants on the surface roughness and energy efficiency of cutting machine tools. After summarizing the achieved experimental results, the authors conclude that cooling lubricants extensively influence the cutting temperature, cutting forces and energy consumption. Also, it is recognizable that cooling lubricants affect the cutting tools lifetime and the workpiece surface quality as well. Furthermore, costs of these cooling lubricants and the related environmental burden need to be considered. A current trend is to reduce the amount of lubricants that are used, e.g., when the Minimum Quantity Lubrication (MQL) technique is applied. The lubricant or process liquid is thereby transported by the compressed air in the form of an aerosol to the contact area between the tool and workpiece. The cutting process was monitored during testing by the three following techniques: lubricant-free cutting, cutting with the use of a lubricant with the MQL technique, and only utilizing finish-turning and finish-face milling. The research allowed the authors to monitor the cutting power and mark the achieved surface quality in relation to the electrical power consumption of the cutting machine. In conclusions, the coherence between energy efficiency of the cutting machine and the workpiece surface quality regarding the used cooling lubricant is described.

  1. Influence of Cooling Lubricants on the Surface Roughness and Energy Efficiency of the Cutting Machine Tools

    Directory of Open Access Journals (Sweden)

    Jersák J.

    2017-08-01

    Full Text Available The Technical University of Liberec and Brandenburg University of Technology Cottbus-Senftenberg investigated the influence of cooling lubricants on the surface roughness and energy efficiency of cutting machine tools. After summarizing the achieved experimental results, the authors conclude that cooling lubricants extensively influence the cutting temperature, cutting forces and energy consumption. Also, it is recognizable that cooling lubricants affect the cutting tools lifetime and the workpiece surface quality as well. Furthermore, costs of these cooling lubricants and the related environmental burden need to be considered. A current trend is to reduce the amount of lubricants that are used, e.g., when the Minimum Quantity Lubrication (MQL technique is applied. The lubricant or process liquid is thereby transported by the compressed air in the form of an aerosol to the contact area between the tool and workpiece. The cutting process was monitored during testing by the three following techniques: lubricant-free cutting, cutting with the use of a lubricant with the MQL technique, and only utilizing finish-turning and finish-face milling. The research allowed the authors to monitor the cutting power and mark the achieved surface quality in relation to the electrical power consumption of the cutting machine. In conclusions, the coherence between energy efficiency of the cutting machine and the workpiece surface quality regarding the used cooling lubricant is described.

  2. Effect of a glaze/composite sealant on the 3-D surface roughness of esthetic restorative materials.

    Science.gov (United States)

    Perez, Cesar dos Reis; Hirata, Raphael Júnior; da Silva, Antonio Henrique Monteiro da Fonseca Thomé; Sampaio, Eduardo Martins; de Miranda, Mauro Sayão

    2009-01-01

    The main goal of the current study was to evaluate the surface roughness of tooth-colored restorative materials after different finishing/polishing protocols, including a liquid polisher (BisCover, BISCO, Schaumburg, IL, USA). The restorative materials tested included two nanofilled resin composites (Filtek Supreme, 3M Dental Products, St Paul, MN, USA and Grandio, Voco, Cuxhaven, Germany), one resin-modified glass ionomer cement (Vitremer, 3M Dental Products) and one conventional glass ionomer cement (Meron Molar ART, Voco). The finishing/polishing methods were divided into five groups: G1 (compression with Mylar matrix), G2 (finishing with diamond burs), G3 (Sof-Lex, 3M Dental Products), G4 (BisCover, BISCO, after diamond burs) and G5 (BisCover after Sof-Lex). Five cylindrical specimens of each material were prepared for each group according to the manufacturer's instructions. The finishing/polishing methods were performed by a single operator in one direction to avoid variations at low speed (15,000 RPM). The surface roughness was evaluated using a 3-D scanning instrument with two parameters considered (Ra and Rz). The data was analyzed using one-way ANOVA followed by a multiple comparison Tukey's test. The results showed that BisCover (BISCO) was capable of reducing surface roughness and provided polished surfaces for all materials, enhancing smoothness over already polished surfaces (Sof-Lex, 3M Dental Products) and achieving polishing after finishing with diamond burs.

  3. Role of roughness parameters on the tribology of randomly nano-textured silicon surface.

    Science.gov (United States)

    Gualtieri, E; Pugno, N; Rota, A; Spagni, A; Lepore, E; Valeri, S

    2011-10-01

    This experimental work is oriented to give a contribution to the knowledge of the relationship among surface roughness parameters and tribological properties of lubricated surfaces; it is well known that these surface properties are strictly related, but a complete comprehension of such correlations is still far to be reached. For this purpose, a mechanical polishing procedure was optimized in order to induce different, but well controlled, morphologies on Si(100) surfaces. The use of different abrasive papers and slurries enabled the formation of a wide spectrum of topographical irregularities (from the submicro- to the nano-scale) and a broad range of surface profiles. An AFM-based morphological and topographical campaign was carried out to characterize each silicon rough surface through a set of parameters. Samples were subsequently water lubricated and tribologically characterized through ball-on-disk tribometer measurements. Indeed, the wettability of each surface was investigated by measuring the water droplet contact angle, that revealed a hydrophilic character for all the surfaces, even if no clear correlation with roughness emerged. Nevertheless, this observation brings input to the purpose, as it allows to exclude that the differences in surface profile affect lubrication. So it is possible to link the dynamic friction coefficient of rough Si samples exclusively to the opportune set of surface roughness parameters that can exhaustively describe both height amplitude variations (Ra, Rdq) and profile periodicity (Rsk, Rku, Ic) that influence asperity-asperity interactions and hydrodynamic lift in different ways. For this main reason they cannot be treated separately, but with dependent approach through which it was possible to explain even counter intuitive results: the unexpected decreasing of friction coefficient with increasing Ra is justifiable by a more consistent increasing of kurtosis Rku.

  4. Effects of fractal roughness of membrane surfaces on interfacial interactions associated with membrane fouling in a membrane bioreactor.

    Science.gov (United States)

    Feng, Shushu; Yu, Genying; Cai, Xiang; Eulade, Mahoro; Lin, Hongjun; Chen, Jianrong; Liu, Yong; Liao, Bao-Qiang

    2017-11-01

    Fractal roughness is one of the most important properties of a fractal surface. In this study, it was found that, randomly rough membrane surface was a fractal surface, which could be digitally modeled by a modified two-variable Weierstrass-Mandelbrot (WM) function. Fractal roughness of membrane surfaces has a typical power function relation with the statistical roughness of the modeled surface. Assessment of interfacial interactions showed that an increase in fractal roughness of membrane surfaces will strengthen and prolong the interfacial interactions between membranes and foulants, and under conditions in this study, will significantly increase the adhesion propensity of a foulant particle on membrane surface. This interesting result can be attributed to that increase in fractal roughness simultaneously improves separation distance and interaction surface area for adhesion of a foulant particle. This study gives deep insights into interfacial interactions and membrane fouling in MBRs. Copyright © 2017 Elsevier Ltd. All rights reserved.

  5. Cell adhesion on Ti surface with controlled roughness

    Directory of Open Access Journals (Sweden)

    Burgos-Asperilla, Laura

    2015-06-01

    Full Text Available In this report, the in situ interaction between Saos-2 osteoblast cells and a smooth Ti surface was examined over time. The adhesion kinetics and mechanisms of cellular proliferation were monitored by quartz crystal microbalance (QCM and electrochemical impedance spectroscopy (EIS. The rate of Saos-2 attachment on Ti surfaces, obtained from the measurements performed with the QCM, is a first-order reaction, with k=2.10−3 min−1. The impedance measurements indicate that in the absence of cells, the Ti resistance diminishes over time (7 days, due to the presence of amino acids and proteins from the culture medium that have been a dsorbed, while in the presence of osteoblasts, this decrease is much greater because of the compounds generated by the cells that accelerate the dissolution of Ti.En este trabajo, se ha estudiado la interacción in situ entre células osteoblásticas Saos-2 y una superficie de Ti de rugosidad controlada a lo largo del tiempo. El estudio de la cinética y los mecanismos de proliferación celular de adhesión se ha realizado a través de la microbalanza de cristal de cuarzo (QCM y espectroscopía de impedancia electroquímica (EIS. La velocidad de adhesión de los osteoblastos sobre la superficie de Ti obtenida a través de medidas con la QCM, sigue una reacción de primer orden, con k=2×10−3 min−1. Los ensayos de impedancia indican que, en ausencia de las células, la resistencia del Ti disminuye con el tiempo (7 días, debido a la presencia de aminoácidos y proteínas del medio de cultivo que se han adsorbido, mientras que en presencia de células, esta disminución es mucho mayor debido a los productos metabólicos generados por las células que aceleran la disolución del Ti.

  6. Functionalized PDMS with versatile and scalable surface roughness gradients for cell culture

    KAUST Repository

    Zhou, Bingpu

    2015-07-21

    This manuscript describes a simple and versatile approach to engineering surface roughness gradients via combination of microfluidics and photo-polymerization. Through UV-mediated polymerization, N-isopropylacrylamide with concentration gradients are successfully grafted onto PDMS surface, leading to diverse roughness degrees on the obtained PDMS substrate. Furthermore, the extent of surface roughness can be controllably regulated via tuning the flow rate ratio between the monomer solution and deionized water. Average roughness ranging from 8.050 nm to 151.68 nm has well been achieved in this work. Such PDMS samples are also demonstrated to be capable of working as supporting substrates for controlling cell adhesion or detachment. Due to the different degrees of surface roughness on a single substrate, our method provides an effective approach for designing advanced surafecs for cell culture. Finally, the thermosensitive property of N-isopropylacrylamide makes our sample furnish as another means for controlling the cell detachment from the substrates with correspondence to the surrounding temperature.

  7. Bone regeneration at implants with turned or rough surfaces in self-contained defects. An experimental study in the dog.

    Science.gov (United States)

    Botticelli, Daniele; Berglundh, Tord; Persson, Leif G; Lindhe, Jan

    2005-05-01

    Marginal hard tissue defects present at implants with a rough surface can heal with a high degree of bone fill and osseointegration. The healing of similar defects adjacent to implants with a smooth surface appears to be less predictable. The aim was to compare bone healing at implants with turned or rough surface topographies placed in self-contained defects using either a submerged or non-submerged installation technique. Six dogs were used. Three months after tooth extraction four experimental sites were prepared for implant installation in both sides of the mandible. The marginal 5 mm of the canal prepared for the implant was widened. Thus, following implant placement a circumferential gap occurred between the bone tissue and the implant surface that was between 1 and 1.25 mm wide. In each side of the mandible two implants with a turned surface and two implants with a rough surface were installed. The implants in the right side were fully submerged, while a non-submerged technique was applied in the left side. The animals were sacrificed 4 months later, block biopsies of each implant site were dissected and ground as well as paraffin sections were prepared. The marginal defects around rough surface implants exhibited after 4 months of healing substantial bone fill and a high degree of osseointegration following either the submerged or the non-submerged installation technique. Healing at turned implants was characterized by incomplete bone fill and the presence of a connective tissue zone between the implant and the newly formed bone. The distance between the implant margin (M) and the most coronal level of bone-to-implant contact (B) at implants with a rough surface was 0.84+/-0.37 mm at submerged and 0.90+/-0.39 mm at non-submerged sites. The distance M-B at implants with a turned surface was 3.39+/-0.52 mm at submerged and 3.23+/-0.68 mm at non-submerged sites. The differences between the rough and turned implants regarding the length of distance M-B were

  8. Surface-roughness driven segregation in a granular slurry under shear

    Science.gov (United States)

    Plantard, G.; Saadaoui, H.; Snabre, P.; Pouligny, B.

    2006-07-01

    "Shear-induced segregation" (SIS) means that different species of particles in a granular material or a concentrated suspension tend to unmix under flow. In principle, any kind of difference (size, density, shape and even surface state) may lead to SIS. We report the first direct experimental evidence of SIS between spheres which only differ by surface characteristics. The effect is observed with a "slurry" made of solid spheres immersed in a viscous fluid, inside a parallel-plate shear device. We show that: i) A mixture of smooth and rough spheres of same size shows considerable SIS. ii) Rough spheres (radius aR) behave similarly to smooth but larger spheres (radius aS > aR). iii) Segregation cancels out for a particular value of the size ratio, aS/aR < 1. These findings can be qualitatively understood from available theories about the role of surface roughness on two-sphere interactions in Stokes regime.

  9. The influence of vibrations on surface roughness formed during precision boring

    Directory of Open Access Journals (Sweden)

    Korzeniewski Dariusz

    2017-01-01

    Full Text Available In this paper, the analysis of vibrations on surface roughness generated during boring with the application of the conventional boring tool and one with the damper is presented. The experiments included the measurement of vibration accelerations carried out with the piezoelectric sensor, as well as the evaluation of surface roughness parameters after each machining pass. The obtained results reveal that in the investigated range, no stability loss was found. Furthermore, the growth of the rotational speed induces the increase of vibration level, as well as the growth of the differences between the vibration values generated during boring with the conventional tool and one equipped with damper. Vibrations have also the direct influence on the machined surface roughness. In case of the tool equipped with the damper, the tool’s overhang L had more intense influence than rotational speed n. However, for the conventional boring tool this dependency was unequivocal.

  10. General contact mechanics theory for randomly rough surfaces with application to rubber friction

    Science.gov (United States)

    Scaraggi, M.; Persson, B. N. J.

    2015-12-01

    We generalize the Persson contact mechanics and rubber friction theory to the case where both surfaces have surface roughness. The solids can be rigid, elastic, or viscoelastic and can be homogeneous or layered. We calculate the contact area, the viscoelastic contribution to the friction force, and the average interface separation as a function of the sliding speed and the nominal contact pressure. We illustrate the theory with numerical results for the classical case of a rubber block sliding on a road surface. We find that with increasing sliding speed, the influence of the roughness on the rubber block decreases to the extent that only the roughness of the stiff counter face needs to be considered.

  11. Models for Surface Roughness Scattering of Electrons in a 2DEG

    International Nuclear Information System (INIS)

    Yarar, Z.

    2004-01-01

    In this work surface roughness scattering of electrons in a two dimensional electron gas (2DEG) formed at heterojunction interfaces is investigated for different auto-correlation tions and potential forms. Gaussian, exponentiaI and lorentsian auto-correlation tions are used to represent surface roughness. Both an infinitely deep triangular potential model and the potential that is found from the numerical solution of Poisson Shrodinger equations self consistently are used as the potential that holds 2DEG at the hetero Interface. Using the wave functions appropriate for the potentials just mentioned and the auto-correlation functions indicated above, the scattering rates due to surface roughness are calculated. The calculations were repeated when the effect of screening is also included for the case of triangular potential

  12. Virtual rough samples to test 3D nanometer-scale scanning electron microscopy stereo photogrammetry.

    Science.gov (United States)

    Villarrubia, J S; Tondare, V N; Vladár, A E

    2016-01-01

    The combination of scanning electron microscopy for high spatial resolution, images from multiple angles to provide 3D information, and commercially available stereo photogrammetry software for 3D reconstruction offers promise for nanometer-scale dimensional metrology in 3D. A method is described to test 3D photogrammetry software by the use of virtual samples-mathematical samples from which simulated images are made for use as inputs to the software under test. The virtual sample is constructed by wrapping a rough skin with any desired power spectral density around a smooth near-trapezoidal line with rounded top corners. Reconstruction is performed with images simulated from different angular viewpoints. The software's reconstructed 3D model is then compared to the known geometry of the virtual sample. Three commercial photogrammetry software packages were tested. Two of them produced results for line height and width that were within close to 1 nm of the correct values. All of the packages exhibited some difficulty in reconstructing details of the surface roughness.

  13. Influence of the ferritic-pearlitic steel microstructure on surface roughness in broaching of automotive steels

    Science.gov (United States)

    Arrieta, I.; Courbon, C.; Cabanettes, F.; Arrazola, P.-J.; Rech, J.

    2017-10-01

    The aim of this work is to characterize the effect of microstructural parameters on surface roughness in dry broaching with a special emphasis on the ferrite-pearlite (FP) ratio. An experimental approach combining cutting and tribological tests has been developed on three grades 27MnCr5, C45, C60 covering a wide range of FP ratio. Fundamental broaching tests have been performed with a single tooth to analyse the resulting surface quality with uncoated M35 HSS tools. A specially designed open tribometer has been used to characterize the friction coefficient at the tool-chip-workpiece interface under appropriate conditions. Specific phenomena have been observed depending on the FP ratio and an interesting correlation with the tribological tests has been found. This clearly shows that friction has an important contribution in broaching and that phase distribution has to be highly considered when cutting a FP steel at a microscopic scale. This work also provides quantitative data of the friction coefficient depending on the sliding velocity and FP content which can be implemented in any analytical or numerical model of a broaching operation.

  14. Increased Surface Roughness in Polydimethylsiloxane Films by Physical and Chemical Methods

    Directory of Open Access Journals (Sweden)

    Jorge Nicolás Cabrera

    2017-08-01

    Full Text Available Two methods, the first physical and the other chemical, were investigated to modify the surface roughness of polydimethylsiloxane (PDMS films. The physical method consisted of dispersing multi-walled carbon nanotubes (MWCNTs and magnetic cobalt ferrites (CoFe2O4 prior to thermal cross-linking, and curing the composite system in the presence of a uniform magnetic field H. The chemical method was based on exposing the films to bromine vapours and then UV-irradiating. The characterizing techniques included scanning electron microscopy (SEM, energy-dispersive spectroscopy (EDS, Fourier transform infrared (FTIR spectroscopy, optical microscopy, atomic force microscopy (AFM and magnetic force microscopy (MFM. The surface roughness was quantitatively analyzed by AFM. In the physical method, the random dispersion of MWCNTs (1% w/w and magnetic nanoparticles (2% w/w generated a roughness increase of about 200% (with respect to PDMS films without any treatment, but that change was 400% for films cured in the presence of H perpendicular to the surface. SEM, AFM and MFM showed that the magnetic particles always remained attached to the carbon nanotubes, and the effect on the roughness was interpreted as being due to a rupture of dispersion randomness and a possible induction of structuring in the direction of H. In the chemical method, the increase in roughness was even greater (1000%. Wells were generated with surface areas that were close to 100 μm2 and depths of up to 500 nm. The observations of AFM images and FTIR spectra were in agreement with the hypothesis of etching by Br radicals generated by UV on the polymer chains. Both methods induced important changes in the surface roughness (the chemical method generated the greatest changes due to the formation of surface wells, which are of great importance in superficial technological processes.

  15. Surface Roughness, Microhardness, and Microleakage of a Silorane-Based Composite Resin after Immediate or Delayed Finishing/Polishing

    Directory of Open Access Journals (Sweden)

    Fernanda Carvalho Rezende Lins

    2016-01-01

    Full Text Available Objective. This study evaluated the effect of immediate or delayed finishing/polishing using different systems on the surface roughness, hardness, and microleakage of a silorane-based composite. Material and Methods. Specimens were made with silorane-based composite (Filtek P90, 3M ESPE and assigned to the treatments: control (light-cured; aluminum oxide discs (Sof-Lex, 3M ESPE; diamond-impregnated silicone tips (Astropol, Ivoclar Vivadent; aluminum oxide-impregnated silicone tips (Enhance, Dentsply. Half of the specimens were finished/polished immediately and the rest after 7 days. Surface roughness (Ra, μm; n=20 and Vickers microhardness (50 g; 45 s; n=10 were measured. Cavities were prepared in bovine incisors and filled with Filtek P90. The fillings received immediate or delayed finishing/polishing (n=10 and were subjected to dye penetration test (0.5% basic fuchsin, 24 h. Data were analyzed by ANOVA and Scheffe, Kruskal-Wallis, and Mann-Whitney tests (p<0.05. Results. The finishing/polishing system significantly influenced roughness and microhardness (p<0.0001. For enamel, microleakage was not affected by the finishing/polishing system (p=0.309. For dentin, Sof-Lex discs and Astropol points promoted greater microleakage than Enhance points (p=0.033. Conclusion. Considering roughness, microhardness, and microleakage together, immediate finishing/polishing of a silorane-based composite using aluminum oxide discs may be recommended.

  16. Hardness and surface roughness of enamel and base layers of resin denture teeth after long-term repeated chemical disinfection.

    Science.gov (United States)

    Neppelenbroek, Karin Hermana; Kurokawa, Luciana Ayumi; Procópio, Andréa Lemos Falcão; Pegoraro, Thiago Amadei; Hotta, Juliana; Mello Lima, Jozely Francisca; Urban, Vanessa Migliorini

    2015-01-01

    To evaluate the effect of successive cycles of disinfection in different denture cleansers on the surface roughness and the Vickers hardness of two layers of acrylic resin (base-BL and enamel-EL) of two commercial cross-linked artificial teeth. The occlusal surfaces of 60 acrylic resin denture posterior teeth (Trilux-TLX and SR Orthosit PE-SRO) embedded in autopolymerizing acrylic resin were ground fat with 1200-grit silicon carbide paper. Specimens were stored in distilled water at 37°C and then submitted to the microhardness (VHN) and roughness (μm) tests. Specimens were stored in distilled water at 37°C for 90 days and submitted to 720 disinfection cycles in sodium hypochlorite at 0.5%, 30% vinegar solution or distilled water (control). Afterward, micro-hardness and roughness tests were again performed. Data were analyzed using two-way ANOVA and Tukey's test (α=0.05). Hypochlorite immersion decreased the hardness of BL and EL of SRO teeth, with an average reduction of 10.11% (p0.37). Hypochlorite promoted deleterious effects on the hardness of both layers of the artificial teeth tested. Immersion in vinegar and water also resulted in reduction of hardness of TLX teeth. The surface hardness of the different layers of cross-linked artificial teeth can be altered by daily disinfection in denture cleansers commonly indicated for removable dentures.

  17. Influence of matrix type on surface roughness of three resins for provisional crowns and fixed partial dentures.

    Science.gov (United States)

    Ayuso-Montero, Raul; Martinez-Gomis, Jordi; Lujan-Climent, Mar; Salsench, Juan; Peraire, Maria

    2009-02-01

    This study evaluated the effect of matrix type on the surface roughness of resins for provisional crowns and fixed partial dentures. Ninety specimens of two acrylic resins (Trim II, Tab2000) and one bis-acryl composite (Protemp II Garant) were fabricated using one of three matrices: irreversible hydrocolloid (Cavex CA37), poly(vinyl siloxane) (Aquasil) or vacuum-formed matrix (Bio-flow Hard). The sample size for each resin-matrix combination was 10. The vestibular face of one natural maxillary central incisor was used as a model to fabricate all the specimens, following the custom fabrication technique. The average roughness measurements, Ra (mum), were obtained using a profilometer, and the data were analyzed using Kruskal-Wallis and Mann-Whitney U-tests. The results were contrasted against the surface roughness of the tooth using a one-sample t-test. Aquasil and vacuum-formed matrix had a smoother surface than Cavex CA37 regardless of the resin tested (p < 0.05). Protemp II Garant had the smoothest surface regardless of the matrix used, with no significant differences when polymerized against the three different matrices. Trim II polymerized against Cavex CA37 had a rougher (p < 0.05) surface than Aquasil or vacuum-formed matrix. Tab2000 had the smoothest surface (p < 0.05) when polymerized against a vacuum-formed matrix. There is no universal matrix that produces the smoothest surface: this depends on the compatibility between the resin and the matrix. Protemp II Garant polymerized against Cavex CA37 matrix yields a surface that is smooth enough not to require polishing unless this surface is adjusted.

  18. Influence of skin surface roughness degree on energy characteristics of light scattered by a biological tissue

    Science.gov (United States)

    Barun, V. V.; Ivanov, A. P.

    2017-05-01

    We present the results of modelling of photometric characteristics of light in soft tissues illuminated by a parallel beam along the normal to the surface, obtained with allowance for the skin roughness parameters and the angular structure of radiation approaching the surface from within the tissue. The depth structure of the fluence rate and the spectra of the diffuse reflection of light by the tissue in the interval of wavelengths 300 - 1000 nm are considered. We discuss the influence of the tilt angle variance of rough surface microelements and light refraction on the studied characteristics. It is shown that these factors lead to the reduction of the radiation flux only in the near-surface tissue layer and practically do not affect the depth of light penetration into the tissue. On the other hand, the degree of the surface roughness and the conditions of its illumination from within the tissue essentially affect the coefficient of diffuse reflection of light and lead to its considerable growth compared to the cases of a smooth interface and completely diffuse illumination, often considered to simplify the theoretical problem solution. The role of the roughness of skin surface is assessed in application to the solution of different direct and inverse problems of biomedical optics.

  19. Roughness modification of surfaces treated by a pulsed dielectric barrier discharge

    CERN Document Server

    Dumitrascu, N; Apetroaei, N; Popa, G

    2002-01-01

    Local modifications of surface roughness are very important in many applications, as this surface property is able to generate new mechano-physical characteristics of a large category of materials. Roughness is one of the most important parameters used to characterize and control the surface morphology, and techniques that allow modifying and controlling the surface roughness present increasing interest. In this respect we propose the dielectric barrier discharge (DBD) as a simple and low cost method that can be used to induce controlled roughness on various surfaces in the nanoscale range. DBD is produced in helium, at atmospheric pressure, by a pulsed high voltage, 28 kV peak to peak, 13.5 kHz frequency and 40 W power. This type of discharge is a source of energy capable of modifying the physico-chemical properties of the surfaces without affecting their bulk properties. The discharge is characterized by means of electrical probes and, in order to analyse the heat transfer rate from the discharge to the tre...

  20. A contact mechanics model for ankle implants with inclusion of surface roughness effects

    International Nuclear Information System (INIS)

    Hodaei, M; Farhang, K; Maani, N

    2014-01-01

    Total ankle replacement is recognized as one of the best procedures to treat painful arthritic ankles. Even though this method can relieve patients from pain and reproduce the physiological functions of the ankle, an improper design can cause an excessive amount of metal debris due to wear, causing toxicity in implant recipient. This paper develops a contact model to treat the interaction of tibia and talus implants in an ankle joint. The contact model describes the interaction of implant rough surfaces including both elastic and plastic deformations. In the model, the tibia and the talus surfaces are viewed as macroscopically conforming cylinders or conforming multi-cylinders containing micrometre-scale roughness. The derived equations relate contact force on the implant and the minimum mean surface separation of the rough surfaces. The force is expressed as a statistical integral function of asperity heights over the possible region of interaction of the roughness of the tibia and the talus implant surfaces. A closed-form approximate equation relating contact force and minimum separation is used to obtain energy loss per cycle in a load–unload sequence applied to the implant. In this way implant surface statistics are related to energy loss in the implant that is responsible for internal void formation and subsequent wear and its harmful toxicity to the implant recipient. (paper)

  1. Roughness Length of Water Vapor over Land Surfaces and Its Influence on Latent Heat Flux

    Directory of Open Access Journals (Sweden)

    Sang-Jong Park

    2010-01-01

    Full Text Available Latent heat flux at the surface is largely dependent on the roughness length for water vapor (z0q. The determination of z0q is still uncertain because of its multifaceted characteristics of surface properties, atmospheric conditions and insufficient observations. In this study, observed values from the Fluxes Over Snow Surface II field experiment (FLOSS-II from November 2002 to March 2003 were utilized to estimate z0q over various land surfaces: bare soil, snow, and senescent grass. The present results indicate that the estimated z0q over bare soil is much smaller than the roughness length of momentum (z0m; thus, the ratio z0m/z0q is larger than those of previous studies by a factor of 20 - 150 for the available flow regime of the roughness Reynolds number, Re* > 0.1. On the snow surface, the ratio is comparable to a previous estimation for the rough flow (Re* > 1, but smaller by a factor of 10 - 50 as the flow became smooth (Re* < 1. Using the estimated ratio, an optimal regression equation of z0m/z0q is determined as a function of Re* for each surface type. The present parameterization of the ratio is found to greatly reduce biases of latent heat flux estimation compared with that estimated by the conventional method, suggesting the usefulness of current parameterization for numerical modeling.

  2. Reflection of diffuse light from dielectric one-dimensional rough surfaces.

    Science.gov (United States)

    González-Alcalde, Alma K; Méndez, Eugenio R; Terán, Emiliano; Cuppo, Fabio L S; Olivares, J A; García-Valenzuela, Augusto

    2016-03-01

    We study the reflection of diffuse light from 1D randomly rough dielectric interfaces. Results for the reflectance under diffuse illumination are obtained by rigorous numerical simulations and then contrasted with those obtained for flat surfaces. We also explore the possibility of using perturbation theories and conclude that they are limited for this type of study. Numerical techniques based on Kirchhoff approximation and reduced Rayleigh equations yield better results. We find that, depending on the refractive index contrast and nature of the irregularities, the roughness can increase or decrease the diffuse reflectance of the surface.

  3. An experimental result of surface roughness machining performance in deep hole drilling

    Directory of Open Access Journals (Sweden)

    Mohamad Azizah

    2016-01-01

    Full Text Available This study presents an experimental result of a deep hole drilling process for Steel material at different machining parameters which are feed rate (f, spindle speed (s, the depth of the hole (d and MQL, number of drops (m on surface roughness, Ra. The experiment was designed using two level full factorial design of experiment (DoE with centre points to collect surface roughness, Ra values. The signal to noise (S/N ratio analysis was used to discover the optimum level for each machining parameters in the experiment.

  4. Development of Fractal Dimension and Characteristic Roughness Models for Turned Surface of Carbon Steels

    Science.gov (United States)

    Zuo, Xue; Zhu, Hua; Zhou, Yuankai; Ding, Cong; Sun, Guodong

    2016-08-01

    Relationships between material hardness, turning parameters (spindle speed and feed rate) and surface parameters (surface roughness Ra, fractal dimension D and characteristic roughness τ∗) are studied and modeled using response surface methodology (RSM). The experiments are carried out on a CNC lathe for six carbon steel material AISI 1010, AISI 1020, AISI 1030, AISI 1045, AISI 1050 and AISI 1060. The profile of turned surface and the surface roughness value are measured by a JB-5C profilometer. Based on the profile data, D and τ∗ are computed through the root-mean-square method. The analysis of variance (ANOVA) reveals that spindle speed is the most significant factors affecting Ra, while material hardness is the most dominant parameter affecting τ∗. Material hardness and spindle speed have the same influence on D. Feed rate has less effect on three surface parameters than spindle speed and material hardness. The second-order models of RSM are established for estimating Ra, D and τ∗. The validity of the developed models is approximately 80%. The response surfaces show that a surface with small Ra and large D and τ∗ can be obtained by selecting a high speed and a large hardness material. According to the established models, Ra, D and τ∗ of six carbon steels surfaces can be predicted under cutting conditions studied in this paper. The results have an instructive meaning to estimate the surface quality before turning.

  5. Fabrication and quantitative roughness analysis of hierarchical multiscale polymer surface structures

    Science.gov (United States)

    Huovinen, Eero; Takkunen, Laura; Suvanto, Mika; Pakkanen, Tapani A.

    2014-05-01

    Nature's functional surfaces are typically hierarchical multiscale structures. There are several techniques for producing such artificial structures on polymers but their mass production is not straightforward. We present here a simple and versatile method for manufacturing hierarchical multiscale polymer surface patterns. The microroughening technique permits the single-step production of multilevel three-dimensional surface architectures in a mechanically durable nickel mold. The molding technique is suitable for area-controlled fabrication of structures with various geometrical shapes on smooth and curved surfaces. The mold structures were transferred to polypropylene surfaces by means of injection molding. The fabricated surface structures were characterized by using a filtered power spectral density method which facilitated a quantitative study of the roughness distributions at different length scales of structure periodicities. Analysis showed that the microroughening technique is an appropriate tool for controlled production of surface roughness at a micro-nanometer scale. Roughness distribution values can be used for predicting surface structure-related properties such as wetting, and the distributions can also be simulated without an experimental preparation process. The work presents a suitable approach for mass production of hierarchical polymer surfaces at different length scales and provides a new route for designing surface structures with tunable wetting properties.

  6. Effect of brushing and thermocycling on the shade and surface roughness of CAD-CAM ceramic restorations.

    Science.gov (United States)

    Yuan, Judy Chia-Chun; Barão, Valentim Adelino Ricardo; Wee, Alvin G; Alfaro, Maria F; Afshari, Fatemeh S; Sukotjo, Cortino

    2017-09-29

    The effects of toothbrushing (B) and thermocycling (TC) on the surface texture of different materials with various fabrication processes have been investigated. However, studies of computer-aided design and computer-aided manufacturing (CAD-CAM) ceramic restorations are limited. The purpose of this in vitro study was to evaluate the effect of B and TC on the color stability and surface roughness of extrinsically characterized and glazed CAD-CAM ceramic restorations. Lithium disilicate CAD ceramic (n=90) and zirconia ceramic (n=90) were studied. All specimens were crystallized/sintered, characterized, and glazed following the manufacturer's recommendation. The specimens were divided into 9 different groups: B, TC, and a combination of B plus TC (B+TC). Brushing was performed at 50 000, 100 000, and 150 000 cycles, simulating an oral environment of 5, 10, and 15 years. Thermocycling was performed at 6000, 12 000, and 18 000 cycles, simulating an oral environment of 5, 10, and 15 years. Brushing plus TC was performed with the combination of the 50 000 cycles of B, then 6000 cycles of TC, and 10 000 cycles of B, then 12 000 cycles of TC, and 15 000 cycles of B, then 18 000 cycles of TC. The color and surface roughness of each specimen were measured before and after all interventions with simulated cycles. Color differences (ΔE) and surface roughness (ΔR a ) data were analyzed using 2-way ANOVA, followed by the least significant difference test (α=.05). The correlation between ΔE and ΔR a was statistically analyzed using the Pearson correlation analysis. Within the lithium disilicate CAD groups, intervention did not result in any significant differences in color change (P>.05). Within the zirconia groups, a 15-year clinical simulation revealed significantly higher ΔE values than a simulated 5-year exposure (P=.017). Increased simulated cycles showed significantly higher R a values for all groups. Within the zirconia groups, B revealed

  7. Effects of decontamination solutions on the surface of titanium: investigation of surface morphology, composition, and roughness.

    Science.gov (United States)

    Wheelis, Sutton E; Gindri, Izabelle M; Valderrama, Pilar; Wilson, Thomas G; Huang, Jessica; Rodrigues, Danieli C

    2016-03-01

    To investigate the impact of treatments used to detoxify dental implants on the oxide layer morphology and to infer how changes in morphology created by these treatments may impact re-osseointegration of an implant. Pure titanium (cpTi) and the alloy Ti6Al4V were subjected to a series of chemical treatments and mechanical abrasion simulating surface decontamination of dental implants. The morphology and roughness of the surface layer before and after treatment with these solutions were investigated with optical and atomic force microscopy (OM, AFM). The solutions employed are typically used for detoxification of dental implants. These included citric acid, 15% hydrogen peroxide, chlorhexidine gluconate, tetracycline, doxycycline, sodium fluoride, peroxyacetic acid, and treatment with carbon dioxide laser. The treatments consisted of both immersions of samples in solution and rubbing with cotton swabs soaked in solution for 1, 2, and 5 min. Cotton swabs used were analyzed with energy dispersive spectroscopy (EDS). The microscopy investigation showed that corrosion and pitting of the samples were present in both metal grades with immersion and rubbing methods when employing more acidic solutions, which had pH acidic solutions caused surface discoloration when coupled with rubbing but did not cause corrosion with immersion. Neutral or basic treatments resulted in no signs of corrosion with both methods. EDS results revealed the presence of titanium particles on all rubbing samples. It was demonstrated in this study that acidic environments coupled with rubbing are able to introduce noticeable morphological changes and corrosion on the surface of both titanium grades. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  8. Robust design optimization method for centrifugal impellers under surface roughness uncertainties due to blade fouling

    Science.gov (United States)

    Ju, Yaping; Zhang, Chuhua

    2016-03-01

    Blade fouling has been proved to be a great threat to compressor performance in operating stage. The current researches on fouling-induced performance degradations of centrifugal compressors are based mainly on simplified roughness models without taking into account the realistic factors such as spatial non-uniformity and randomness of the fouling-induced surface roughness. Moreover, little attention has been paid to the robust design optimization of centrifugal compressor impellers with considerations of blade fouling. In this paper, a multi-objective robust design optimization method is developed for centrifugal impellers under surface roughness uncertainties due to blade fouling. A three-dimensional surface roughness map is proposed to describe the nonuniformity and randomness of realistic fouling accumulations on blades. To lower computational cost in robust design optimization, the support vector regression (SVR) metamodel is combined with the Monte Carlo simulation (MCS) method to conduct the uncertainty analysis of fouled impeller performance. The analyzed results show that the critical fouled region associated with impeller performance degradations lies at the leading edge of blade tip. The SVR metamodel has been proved to be an efficient and accurate means in the detection of impeller performance variations caused by roughness uncertainties. After design optimization, the robust optimal design is found to be more efficient and less sensitive to fouling uncertainties while maintaining good impeller performance in the clean condition. This research proposes a systematic design optimization method for centrifugal compressors with considerations of blade fouling, providing a practical guidance to the design of advanced centrifugal compressors.

  9. Study on surface roughness evolvement of Nd-doped phosphate glass after IBF

    Science.gov (United States)

    Li, Furen; Xie, Xuhui; Zhou, Lin; Tie, Guipeng; Hu, Hao

    2016-10-01

    Nd doped phosphate glass is widely used as gain media in high power laser system. It is traditionally polished with the annular polishing technology. The edge effect is inevitable in annular polishing process and it results in the low manufacturing efficiency. Ion Beam Figuring (IBF) is a highly deterministic, non-contact method for the ultra-precision optics fabrication. So the edge effect is avoided. Nanometer and sub-nanometer precision is realizable in IBF. In this paper, Nd doped phosphate glass was polished with IBF, and the evolvement of surface roughness was emphasized. The roughness of surface polished with ion beam at normal and oblique incidence was researched. The oblique incident angle was 45°. The surface roughness was measured with the white light interferometer. No evident change was observed. This means that the pre-finish roughness can be preserved in IBF. The results denote that IBF is a feasible method to correct the contour errors of Nd doped phosphate glass, and the roughness will not be coarsened.

  10. Finite element method analysis of surface roughness transfer in micro flexible rolling

    OpenAIRE

    Qu Feijun; Xie Haibo; Jiang Zhengyi

    2016-01-01

    Micro flexible rolling aims to fabricate submillimeter thick strips with varying thickness profile, where the surface quality of products is mainly determined by initial workpiece surface roughness and subsequent surface asperity flattening process, which is affected by process parameters during rolling. This paper shows a 3D finite element model for flexible rolling of a 250 μm thick workpiece with reduction of 20 to 50%, and rolling phase with thinner thickness indicates a better ability to...

  11. General contact mechanics theory for randomly rough surfaces with application to rubber friction

    OpenAIRE

    Scaraggi, Michele; Persson, Bo N. J.

    2015-01-01

    We generalize the Persson contact mechanics and rubber friction theory to the case where both surfaces have surface roughness. The solids can be rigid, elastic or viscoelastic, and can be homogeneous or layered. We calculate the contact area, the viscoelastic contribution to the friction force, and the average interfacial separation as a function of the sliding speed and the nominal contact pressure. We illustrate the theory with numerical results for a rubber block sliding on a road surface....

  12. The effects of surface roughness on low haze ultrathin nanocomposite films

    Energy Technology Data Exchange (ETDEWEB)

    Kanniah, Vinod [Chemical and Materials Engineering, 177 F. Paul Anderson Tower, University of Kentucky, Lexington, KY 40506 (United States); Tru Vue, Inc. 9400 West, 55th St, McCook, IL 60525 (United States); Grulke, Eric A., E-mail: eric.grulke@uky.edu [Chemical and Materials Engineering, 177 F. Paul Anderson Tower, University of Kentucky, Lexington, KY 40506 (United States); Druffel, Thad [Vision Dynamics LLC, 1950 Production Court, Louisville, KY 40299 (United States); Conn Center for Renewable Energy Research, University of Louisville, Ernst Hall Room 102A, Louisville, KY 40292 (United States)

    2013-07-31

    Control of surface roughness in optical applications can have a large impact on haze. This work compares surface roughness and haze for self-assembled experimental surface structures as well as simulated surface structures for ultrathin nanocomposite films. Ultrathin nanocomposite films were synthesized from an acrylate monomer as the continuous phase with monodisperse or bidisperse mixtures of silica nanoparticles as the dispersed phase. An in-house spin coating deposition technique was used to make thin nanocomposite films on hydrophilic (glass) and hydrophobic (polycarbonate) substrates. Manipulating the size ratios of the silica nan