WorldWideScience

Sample records for surface renewal sr

  1. Computational efficiency for the surface renewal method

    Science.gov (United States)

    Kelley, Jason; Higgins, Chad

    2018-04-01

    Measuring surface fluxes using the surface renewal (SR) method requires programmatic algorithms for tabulation, algebraic calculation, and data quality control. A number of different methods have been published describing automated calibration of SR parameters. Because the SR method utilizes high-frequency (10 Hz+) measurements, some steps in the flux calculation are computationally expensive, especially when automating SR to perform many iterations of these calculations. Several new algorithms were written that perform the required calculations more efficiently and rapidly, and that tested for sensitivity to length of flux averaging period, ability to measure over a large range of lag timescales, and overall computational efficiency. These algorithms utilize signal processing techniques and algebraic simplifications that demonstrate simple modifications that dramatically improve computational efficiency. The results here complement efforts by other authors to standardize a robust and accurate computational SR method. Increased speed of computation time grants flexibility to implementing the SR method, opening new avenues for SR to be used in research, for applied monitoring, and in novel field deployments.

  2. Surface Renewal Application for Estimating Evapotranspiration: A Review

    Directory of Open Access Journals (Sweden)

    Yongguang Hu

    2018-01-01

    Full Text Available The estimation of evapotranspiration (ET is essential for meteorological modeling of surface exchange processes, as well as for the agricultural practice of irrigation management. Hitherto, a number of methods for estimation of ET at different temporal scales and climatic conditions are constantly under investigation and improvement. One of these methods is surface renewal (SR. Therefore, the premise of this review is to present recent developments and applications of SR for ET measurements. The SR method is based on estimating the turbulent exchange of sensible heat flux between plant canopy and atmosphere caused by the instantaneous replacement of air parcels in contact with the surface. Additional measurements of net radiation and soil heat flux facilitate extracting ET using the shortened energy balance equation. The challenge, however, is the calibration of SR results against direct sensible heat flux measurements. For the classical SR method, only air temperature measured at high frequency is required. In addition, a new model suggests that the SR method could be exempted from calibration by measuring additional micrometeorological variables. However, further improvement of the SR method is required to provide improved results in the future.

  3. SURFACE ENERGY BALANCE OVER ORANGE ORCHARD USING SURFACE RENEWAL ANALYSIS

    Directory of Open Access Journals (Sweden)

    Salvatore Barbagallo

    2009-12-01

    Full Text Available Reliable estimation of surface sensible and latent heat flux is the most important process to appraise energy and mass exchange among atmosphere and biosphere. In this study the surface energy fluxes were measured over an irrigated orange orchard during 2005-2008 monitoring periods using a Surface Renewal- Energy Balance approach. The experimental area is located in a representative orchard growing area of eastern Sicily (Italy. The performance of Surface Renewal (SR analysis for estimating sensible heat flux (H was analysed and evaluated in terms of correlation with H fluxes from the eddy covariance (EC method. Study revealed that the mean available energy (RN- G and latent heat flux (LE were of about 300 W m-2 and 237 W m-2, respectively, during dry periods and unstable-case atmospheric conditions. The estimated crop coefficient Kc values for the orchard crop averaged close to 0.80, which is considerably higher than previous FAO studies that found the value to be 0.65 for citrus with 70% of ground cover. The intercepted photosynthetically active radiation (LI PAR by the crop was measured and relationships between LAI and crop coefficient (Kc were established.

  4. Electronic properties and surface reactivity of SrO-terminated SrTiO3 and SrO-terminated iron-doped SrTiO3.

    Science.gov (United States)

    Staykov, Aleksandar; Tellez, Helena; Druce, John; Wu, Ji; Ishihara, Tatsumi; Kilner, John

    2018-01-01

    Surface reactivity and near-surface electronic properties of SrO-terminated SrTiO 3 and iron doped SrTiO 3 were studied with first principle methods. We have investigated the density of states (DOS) of bulk SrTiO 3 and compared it to DOS of iron-doped SrTiO 3 with different oxidation states of iron corresponding to varying oxygen vacancy content within the bulk material. The obtained bulk DOS was compared to near-surface DOS, i.e. surface states, for both SrO-terminated surface of SrTiO 3 and iron-doped SrTiO 3 . Electron density plots and electron density distribution through the entire slab models were investigated in order to understand the origin of surface electrons that can participate in oxygen reduction reaction. Furthermore, we have compared oxygen reduction reactions at elevated temperatures for SrO surfaces with and without oxygen vacancies. Our calculations demonstrate that the conduction band, which is formed mainly by the d-states of Ti, and Fe-induced states within the band gap of SrTiO 3 , are accessible only on TiO 2 terminated SrTiO 3 surface while the SrO-terminated surface introduces a tunneling barrier for the electrons populating the conductance band. First principle molecular dynamics demonstrated that at elevated temperatures the surface oxygen vacancies are essential for the oxygen reduction reaction.

  5. Surface renewal as a significant mechanism for dust emission

    Directory of Open Access Journals (Sweden)

    J. Zhang

    2016-12-01

    Full Text Available Wind tunnel experiments of dust emissions from different soil surfaces are carried out to better understand dust emission mechanisms. The effects of surface renewal on aerodynamic entrainment and saltation bombardment are analyzed in detail. It is found that flow conditions, surface particle motions (saltation and creep, soil dust content and ground obstacles all strongly affect dust emission, causing its rate to vary over orders of magnitude. Aerodynamic entrainment is highly effective, if dust supply is unlimited, as in the first 2–3 min of our wind tunnel runs. While aerodynamic entrainment is suppressed by dust supply limits, surface renewal through the motion of surface particles appears to be an effective pathway to remove the supply limit. Surface renewal is also found to be important to the efficiency of saltation bombardment. We demonstrate that surface renewal is a significant mechanism affecting dust emission and recommend that this mechanism be included in future dust models.

  6. Surface modeling and chemical solution deposition of SrO(SrTiO3)n Ruddlesden-Popper phases

    International Nuclear Information System (INIS)

    Zschornak, M.; Gemming, S.; Gutmann, E.; Weissbach, T.; Stoecker, H.; Leisegang, T.; Riedl, T.; Traenkner, M.; Gemming, T.; Meyer, D.C.

    2010-01-01

    Strontium titanate (STO) is a preferred substrate material for functional oxide growth, whose surface properties can be adjusted through the presence of Ruddlesden-Popper (RP) phases. Here, density functional theory (DFT) is used to model the (1 0 0) and (0 0 1) surfaces of SrO(SrTiO 3 ) n RP phases. Relaxed surface structures, electronic properties and stability relations have been determined. In contrast to pure STO, the near-surface SrO-OSr stacking fault can be employed to control surface roughness by adjusting SrO and TiO 2 surface rumpling, to stabilize SrO termination in an SrO-rich surrounding or to increase the band gap in the case of TiO 2 termination. RP thin films have been epitaxially grown on (0 0 1) STO substrates by chemical solution deposition. In agreement with DFT results, the fraction of particular RP phases n = 1-3 changes with varying heating rate and molar ratio Sr:Ti. This is discussed in terms of bulk formation energy.

  7. Changes in local surface structure and Sr depletion in Fe-implanted SrTiO{sub 3} (001)

    Energy Technology Data Exchange (ETDEWEB)

    Lobacheva, O., E-mail: olobache@gmail.com [Department of Physics and Astronomy, Western University, London, ON N6A 5B7 (Canada); Yiu, Y.M. [Department of Chemistry, Western University, London, ON N6A 5B7 (Canada); Chen, N. [Canadian Light Source, Saskatoon, SK S7N 0X4 (Canada); Sham, T.K.; Goncharova, L.V. [Department of Physics and Astronomy, Western University, London, ON N6A 5B7 (Canada); Department of Chemistry, Western University, London, ON N6A 5B7 (Canada)

    2017-01-30

    Highlights: • Fe ion implantation of SrTiO{sub 3} and post-implantation results in formation of Sr{sub 1-y}Ti{sub 1-x}Fe{sub x+y}O{sub 3-δ} phase. • In Sr{sub 1-y}Ti{sub 1-x}Fe{sub x+y}O{sub 3-δ} phase, Fe assumes Fe{sup 3+} oxidation state in the bulk and Fe{sup 2+} oxidation state in the near surface area. • FEFF9 calculations indicate that Fe ions can substitute both Ti and Sr sites. • Formation of Sr{sub 1-y}Ti{sub 1-x}Fe{sub x+y}O{sub 3-δ} phase is accompanied by Sr depletion in the near surface region. - Abstract: Local surface structure of single crystal strontium titanate SrTiO{sub 3} (001) samples implanted with Fe in the range of concentrations between 2 × 10{sup 14} to 2 × 10{sup 16} Fe/cm{sup 2} at 30 keV has been investigated. In order to facilitate Fe substitution (doping), implanted samples were annealed in oxygen at 350 °C. Sr depletion was observed from the near-surface layers impacted by the ion-implantation process, as revealed by Rutherford Backscattering Spectrometry (RBS), X-ray photoelectron spectroscopy (XPS), X-ray Absorption Near Edge Spectroscopy (XANES), and Atomic Force Microscopy (AFM). Hydrocarbon contaminations on the surface may contribute to the mechanisms of Sr depletion, which have important implications for Sr(Ti{sub 1-x}Fe{sub x})O{sub 3-δ} materials in gas sensing applications.

  8. Advances in the Surface Renewal Flux Measurement Method

    Science.gov (United States)

    Shapland, T. M.; McElrone, A.; Paw U, K. T.; Snyder, R. L.

    2011-12-01

    The measurement of ecosystem-scale energy and mass fluxes between the planetary surface and the atmosphere is crucial for understanding geophysical processes. Surface renewal is a flux measurement technique based on analyzing the turbulent coherent structures that interact with the surface. It is a less expensive technique because it does not require fast-response velocity measurements, but only a fast-response scalar measurement. It is therefore also a useful tool for the study of the global cycling of trace gases. Currently, surface renewal requires calibration against another flux measurement technique, such as eddy covariance, to account for the linear bias of its measurements. We present two advances in the surface renewal theory and methodology that bring the technique closer to becoming a fully independent flux measurement method. The first advance develops the theory of turbulent coherent structure transport associated with the different scales of coherent structures. A novel method was developed for identifying the scalar change rate within structures at different scales. Our results suggest that for canopies less than one meter in height, the second smallest coherent structure scale dominates the energy and mass flux process. Using the method for resolving the scalar exchange rate of the second smallest coherent structure scale, calibration is unnecessary for surface renewal measurements over short canopies. This study forms the foundation for analysis over more complex surfaces. The second advance is a sensor frequency response correction for measuring the sensible heat flux via surface renewal. Inexpensive fine-wire thermocouples are frequently used to record high frequency temperature data in the surface renewal technique. The sensible heat flux is used in conjunction with net radiation and ground heat flux measurements to determine the latent heat flux as the energy balance residual. The robust thermocouples commonly used in field experiments

  9. The surface renewal method for better spatial resolution of evapotranspiration measurements

    Science.gov (United States)

    Suvocarev, K.; Fischer, M.; Massey, J. H.; Reba, M. L.; Runkle, B.

    2017-12-01

    Evaluating feasible irrigation strategies when water is scarce requires measurements or estimations of evapotranspiration (ET). Direct observations of ET from agricultural fields are preferred, and micrometeorological methods such as eddy covariance (EC) provide a high quality, continuous time series of ET. However, when replicates of the measurements are needed to compare irrigation strategies, the cost of such experiments is often prohibitive and limits experimental scope. An alternative micrometeorological approach to ET, the surface renewal (SR) method, may be reduced to a thermocouple and a propeller anemometer (Castellvi and Snyder, 2009). In this case, net radiation, soil and sensible heat flux (H) are measured and latent heat flux (an energy equivalent for ET) is estimated as the residual of the surface energy-balance equation. In our experiment, thermocouples (Type E Fine-Wire Thermocouple, FW3) were deployed next to the EC system and combined with mean horizontal wind speed measurements to obtain H using SR method for three weeks. After compensating the temperature signal for non-ideal frequency response in the wavelet half-plane and correcting the sonic anemometer for the flow distortion (Horst et al., 2015), the SR H fluxes compared well to those measured by EC (r2 = 0.9, slope = 0.92). This result encouraged us to install thermocouples over 16 rice fields under different irrigation treatments (continuous cascade flood, continuous multiple inlet rice irrigation, alternate wetting and drying, and furrow irrigation). The EC measurements with net radiometer and soil heat flux plates are deployed at three of these fields to provide a direct comparison. The measurement campaign will finish soon and the data will be processed to evaluate the SR approach for ET estimation. The results will be used to show better spatial resolution of ET measurements to support irrigation decisions in agricultural crops.

  10. Surface renewal method for estimating sensible heat flux | Mengistu ...

    African Journals Online (AJOL)

    There are 2 SR analysis approaches: the ideal SR analysis approach which ... canopy structure and stability conditions since it depends on the capability of the ... A combination approach using SR and either similarity theory, that requires ...

  11. A surface-renewal model of cross-flow microfiltration

    Directory of Open Access Journals (Sweden)

    A. Hasan

    2013-03-01

    Full Text Available A mathematical model using classical cake-filtration theory and the surface-renewal concept is formulated for describing cross-flow microfiltration under dynamic and steady-state conditions. The model can predict the permeate flux and cake buildup in the filter. The three basic parameters of the model are the membrane resistance, specific cake resistance and rate of surface renewal. The model is able to correlate experimental permeate flow rate data in the microfiltration of fermentation broths in laboratory- and pilot-scale units with an average root-mean-square (RMS error of 4.6%. The experimental data are also compared against the critical-flux model of cross-flow microfiltration, which has average RMS errors of 6.3, 5.5 and 6.1% for the cases of cake filtration, intermediate blocking and complete blocking mechanisms, respectively.

  12. Surface renewal analysis for estimating turbulent surface fluxes

    International Nuclear Information System (INIS)

    Castellvi, F.

    2009-01-01

    A decade ago, the need for a long-term surface monitoring was recognized to better understand the soil-vegetation-atmosphere scalar exchange and interaction processes. the AmeriFlux concept emerged in the IGBP workshop (La Thuile, IT, 1995). Continuous acquisition of surface fluxes for different species such as temperature, water vapour, CO x , halocarbon, ozone, etc.,) and momentum allows determination of the influence of local (canopy) exchanges, fossil fuel emission, large-scale biotic exchange on ambient concentrations which are crucial to take decisions for protecting natural environments and water resources, to develop new perspective for modern agriculture and forest management and to better understand the global climate change. (Author)

  13. Surface structural reconstruction of SrVO3 thin films on SrTiO3 (001)

    Science.gov (United States)

    Wang, Gaomin; Saghayezhian, Mohammad; Chen, Lina; Guo, Hangwen; Zhang, Jiandi

    Paramagnetic metallic oxide SrVO3>(SVO) is an itinerant system known to undergo thickness-induced metal-insulator-transition (MIT) in ultrathin film form, which makes it a prototype system for the study of the mechanism behind metal-insulator-transition like structure distortion, electron correlations and disorder-induced localization. We have grown SrVO3 thin film with atomically flat surface through the layer-by-layer deposition by laser Molecular Beam Epitaxy (laser-MBE) on SrTiO3 (001) surface. Low Energy Electron Diffraction (LEED) measurements reveal that there is a (√2X √2) R45°surface reconstruction independent of film thickness. By using LEED-I(V) structure refinement, we determine the surface structure. In combination with X-ray Photoelectron Spectroscopy (XPS) and Scanning Tunneling Microscopy (STM), we discuss the implication on the MIT in ultrathin films below 2-3 unit cell thickness. This work is supported by the National Science Foundation under the NSF EPSCoR Cooperative Agreement No. EPS-1003897 with additional support from the Louisiana Board of Regents.

  14. Biological response of Sr-containing coating with various surface treatments on titanium substrate for medical applications

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Shih-Ping [Department of Materials Science and Engineering, National Cheng Kung University, Tainan, Taiwan (China); Lee, Tzer-Min, E-mail: tmlee@mail.ncku.edu.tw [Institute of Oral Medicine, National Cheng Kung University, Tainan, Taiwan (China); School of Dentistry, Kaohsiung Medical University, Kaohsiung, Taiwan (China); Lui, Truan-Sheng [Department of Materials Science and Engineering, National Cheng Kung University, Tainan, Taiwan (China)

    2015-08-15

    Graphical abstract: - Highlights: • Sr-containing coating prepared by plasma spraying and micro-arc oxidation process, respectively. • MAO coating stimulated high ECM-like structures of cells on early stage. • Sr-containing specimens had high cell responses on late stage. • Sr-MAO coating is a desirable implant surface treatment for clinical applications. - Abstract: An implant requires a suitable surface to trigger osteointegration. The surface characteristics and chemical composition are important factors in this process. Plasma spraying and micro-arc oxidation can be used to fabricate rough and porous structures for medical applications. Strontium (Sr) has been shown to prevent osteoporosis in vitro and in vivo. However, few scientists have evaluated the biological response of Sr-containing coatings on different surface treatments. In this study, a sand-blasted (SB) surface (as the control), plasma-sprayed hydroxyapatite (HA) and Sr-substituted HA coatings (HAPS and SrHAPS, respectively), calcium phosphate and Sr-containing calcium phosphate micro-arc oxidation surface (CPM and SrCPM, respectively) were analyzed in terms of human osteoblastic cell (MG63) response. Sr was confirmed to be incorporated into the surface. SrHAPS and SrCPM specimens had higher cell responses than those of the HAPS and CPM groups, respectively. The cells cultured on SrCPM and SrHAPS specimens exhibited high proliferation and differentiation. However, CPM and SrCPM specimens stimulated more ECM-like structures than other specimens. The results show that Sr-containing coatings have good characteristics that enhance cell response. The SrCPM coating is a suitable implant surface treatment for clinical applications.

  15. Biological response of Sr-containing coating with various surface treatments on titanium substrate for medical applications

    International Nuclear Information System (INIS)

    Yang, Shih-Ping; Lee, Tzer-Min; Lui, Truan-Sheng

    2015-01-01

    Graphical abstract: - Highlights: • Sr-containing coating prepared by plasma spraying and micro-arc oxidation process, respectively. • MAO coating stimulated high ECM-like structures of cells on early stage. • Sr-containing specimens had high cell responses on late stage. • Sr-MAO coating is a desirable implant surface treatment for clinical applications. - Abstract: An implant requires a suitable surface to trigger osteointegration. The surface characteristics and chemical composition are important factors in this process. Plasma spraying and micro-arc oxidation can be used to fabricate rough and porous structures for medical applications. Strontium (Sr) has been shown to prevent osteoporosis in vitro and in vivo. However, few scientists have evaluated the biological response of Sr-containing coatings on different surface treatments. In this study, a sand-blasted (SB) surface (as the control), plasma-sprayed hydroxyapatite (HA) and Sr-substituted HA coatings (HAPS and SrHAPS, respectively), calcium phosphate and Sr-containing calcium phosphate micro-arc oxidation surface (CPM and SrCPM, respectively) were analyzed in terms of human osteoblastic cell (MG63) response. Sr was confirmed to be incorporated into the surface. SrHAPS and SrCPM specimens had higher cell responses than those of the HAPS and CPM groups, respectively. The cells cultured on SrCPM and SrHAPS specimens exhibited high proliferation and differentiation. However, CPM and SrCPM specimens stimulated more ECM-like structures than other specimens. The results show that Sr-containing coatings have good characteristics that enhance cell response. The SrCPM coating is a suitable implant surface treatment for clinical applications

  16. Hybrid HF-DFT comparative study of SrZrO{sub 3} and SrTiO{sub 3}(001) surface properties

    Energy Technology Data Exchange (ETDEWEB)

    Evarestov, R.A.; Bandura, A.V.; Alexandrov, V.E. [Department of Quantum Chemistry, St. Petersburg State University, 26 Universitetskii Prospekt, Stary Petergof, 198504 St. Petersburg (Russian Federation)

    2006-10-15

    Hybrid HF-DFT LCAO simulations of SrZrO{sub 3} and SrTiO{sub 3}(001) surface properties are performed in a single-slab model framework. The SrZrO{sub 3}(001) surface was studied by an ab initio method for the first time. Three slab models with different surface terminations including up to 8 atomic planes were used for calculation of the various surface characteristics (surface energies, atomic charges, density of electronic states). The dependence of the results on the chosen model and on the kind of d-element is analyzed. The dissimilarity in the surface oxygen atom contributions to the total density of states of two crystals is attributed to the more ionic nature of Zr-O bonds compared to Ti-O bonds. It is found that in the case of SrZrO{sub 3} the electronic density is biased towards the SrO-terminated surface and this surface should be more basic in nature than the SrO surface of SrTiO{sub 3} crystal. (copyright 2006 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  17. Sorption of U(VI) in surfaces of SrTiO3

    International Nuclear Information System (INIS)

    Ortiz O, H.B.; Ordonez R, E.; Fernandez V, S.M.

    2004-01-01

    In this work is presented the physico chemical characterization and evaluation of those surface properties and of sorption of U on the SrTiO 3 like possible candidate for contention barrier in the deep geological confinement. The made studies showed that the SrTiO 3 presents maximum levels of sorption of positive nature species (mainly UO 2 2+ and UO 2 NO 3 + ). (Author)

  18. Geochemical tracing of As pollution in the Orbiel Valley (southern France): 87Sr/86Sr as a tracer of the anthropogenic arsenic in surface and groundwater.

    Science.gov (United States)

    Khaska, Mahmoud; Le Gal La Salle, Corinnne; Lancelot, Joël; Verdoux, Patrick; Boutin, René

    2014-05-01

    The environmental impacts of arsenic mining activities and their effects on ecosystem and human health are observed in many stream waters and groundwater. The aim of this study is to identify the origin of As content in a mining environment using Sr isotopes. At the Salsigne gold mine, before the closure in 2004, high arsenic content has been observed in surface water and groundwater in the Orbiel valley. At the site, immobilization of As, in As rich leachate, is carried out by adding CaO. High contrast in 87Sr/86Sr between Arsenic rich minerals associated with Variscan metamorphic rocks (0.714888-0.718835), together with rich As waste water (0.713463-715477), and the CaO (0.707593) allows as to trace the origin of anthropogenic As. In 2012, Orbiel stream waters were sampled monthly upstream and downstream from the ancient ore processing site and once after an important rainy event (117mm). The upstream valley samples showed low and relatively constant As content with natural regional background of 3.6 and 5.6 μg/L. The rainy event induced only a slight increase in the As content up to 6.3 μg/L. High 87Sr/86Sr ratios suggested an influence of radiogenic Sr issued from the Variscan metamorphic basement. Downstream from the area, the As content was at least10 time as high. In the wet season, stream water As content clearly increased to 13.9-24 μg/L, reaching 120.5 μg/L during the rainy event. Associated 87Sr/86Sr ratio showed to be less radiogenic (0.712276-0.714002). The anti correlation observed between As and 87Sr/86Sr suggest that As issued from a natural origin is characterised by a high 87Sr/86Sr compared to As derived from the CaO treatement used on site and characterized by a low 87Sr/86Sr ratio. During the dry season, increase in As content was observed reaching 110 μg/L. These highlights the contribution of alluvial groundwater to base flow, probably associated with As reach leachate from the site. Contribution from the alluvial aquifer is confirmed by

  19. Surface Decontamination Studies of Cs-137 and Sr-85 Using Polymer Gel

    International Nuclear Information System (INIS)

    Pham, L.; Nguyen, C.; Nguyen, L.

    2015-01-01

    Strippable polymer coating is one of the methods for effective surface decontamination to remove isotopes on the contaminated surface. This method is applying in nuclear facilities on the World. In this paper, we present the results obtained in our laboratory from product the polymer coating to apply to remove radioisotopes of "1"3"7Cs and "8"5Sr from surface of glass, stainless steel, mild steel, ceramic, PVC plastic. This polymer gel solution consist of water soluble polymer preferably polyvinyl alcohol (PVA), plasticizing agent (glycerine) and chelating agents, (citric acid) which can be sprayed or pasted on to contaminated surface. After some hours, these gel solutions was dried to form a strong thin film and it was easily peeled off from a contaminated surface with the radioactive isotopes and can be disposed off as radioactive solid waste. In this study infrared spectrophotometry technique was used to examine the interaction of the cesium and strontium ions with polyvinyl alcohol (PVA), polymer gel and the results of the study were also presented. The results showed that decontamination efficiency of "1"3"7Cs and "8"5Sr strongly depended on property, porosity and smoothness of the contaminated surface and obtained from 95-99% on glass and stainless steel, ceramic and PVC plastic surfaces. The decontamination efficiency also depended on activity and coating thickness. Optimization of film thickness is around 0.2 mm. Decontamination efficiency of Polymer gel were compared with Decongel 1101 (product from USA) on surfaces. IR spectra studies indicated that Cs and Sr ions interacted with PVA and citric acid in Polymer gel through cacboxyl (C = O) group. Polymer gel could remove of "1"3"7Cs and "8"5Sr better than PVA gel does because of citric acid, which can form chelating complex with Cs and Sr ion. (author)

  20. Sorption of U(VI) in surfaces of SrTiO{sub 3}; Sorcion de U(VI) en superficies de SrTiO{sub 3}

    Energy Technology Data Exchange (ETDEWEB)

    Ortiz O, H.B.; Ordonez R, E.; Fernandez V, S.M. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)

    2004-07-01

    In this work is presented the physico chemical characterization and evaluation of those surface properties and of sorption of U on the SrTiO{sub 3} like possible candidate for contention barrier in the deep geological confinement. The made studies showed that the SrTiO{sub 3} presents maximum levels of sorption of positive nature species (mainly UO{sub 2}{sup 2+} and UO{sub 2}NO{sub 3}{sup +}). (Author)

  1. Estimation of sensible and latent heat flux from natural sparse vegetation surfaces using surface renewal

    Science.gov (United States)

    Zapata, N.; Martínez-Cob, A.

    2001-12-01

    This paper reports a study undertaken to evaluate the feasibility of the surface renewal method to accurately estimate long-term evaporation from the playa and margins of an endorreic salty lagoon (Gallocanta lagoon, Spain) under semiarid conditions. High-frequency temperature readings were taken for two time lags ( r) and three measurement heights ( z) in order to get surface renewal sensible heat flux ( HSR) values. These values were compared against eddy covariance sensible heat flux ( HEC) values for a calibration period (25-30 July 2000). Error analysis statistics (index of agreement, IA; root mean square error, RMSE; and systematic mean square error, MSEs) showed that the agreement between HSR and HEC improved as measurement height decreased and time lag increased. Calibration factors α were obtained for all analyzed cases. The best results were obtained for the z=0.9 m ( r=0.75 s) case for which α=1.0 was observed. In this case, uncertainty was about 10% in terms of relative error ( RE). Latent heat flux values were obtained by solving the energy balance equation for both the surface renewal ( LESR) and the eddy covariance ( LEEC) methods, using HSR and HEC, respectively, and measurements of net radiation and soil heat flux. For the calibration period, error analysis statistics for LESR were quite similar to those for HSR, although errors were mostly at random. LESR uncertainty was less than 9%. Calibration factors were applied for a validation data subset (30 July-4 August 2000) for which meteorological conditions were somewhat different (higher temperatures and wind speed and lower solar and net radiation). Error analysis statistics for both HSR and LESR were quite good for all cases showing the goodness of the calibration factors. Nevertheless, the results obtained for the z=0.9 m ( r=0.75 s) case were still the best ones.

  2. Sr/Ca-Sea surface temperature calibration in the branching Caribbean coral Acropora palmata

    Science.gov (United States)

    Gallup, Christina D.; Olson, Donna M.; Edwards, R. Lawrence; Gruhn, Leah M.; Winter, Amos; Taylor, Frederick W.

    2006-02-01

    We measured Sr/Ca ratios by thermal ionization mass spectrometry in radial and axial growth of modern Caribbean Acropora palmata corals. Comparison of our results with sea surface temperature (SST) allows radial and axial Sr/Ca-SST calibrations of Sr/Ca (mmol/mol) = 11.30 - 0.07072 × SST (°C) and Sr/Ca (mmol/mol) = 11.32 - 0.06281 x SST (°C), respectively. Application of the calibrations to fossil Acropora palmata from the last glacial maximum in Barbados (Guilderson et al., 1994) imply ~7°C cooler conditions than the present, much larger than the 1-1.5° cooling suggested by modern analog technique foraminifera-based estimates (Trend-Staid and Prell, 2002). If the foraminifera-based estimates are correct, then the excess cooling suggested by the Barbados corals could be explained by a 5% shift in the marine Sr/Ca ratio or an addition of ~20% abiotic secondary aragonite.

  3. Oxygen dosing the surface of SrTiO{sub 3}

    Energy Technology Data Exchange (ETDEWEB)

    Dudy, L.; Scheiderer, P.; Schuetz, P.; Gabel, J.; Buchwald, M.; Sing, M.; Claessen, R. [Physikalisches Institut, Universitaet Wuerzburg (Germany); Denlinger, J.D. [Advanced Light Source, Lawrence Berkeley National Laboratory, Berkeley, CA, 94270 (United States); Schlueter, C.; Lee, T.L. [Diamond Light Source Ltd., Didcot, Oxfordshire (United Kingdom)

    2015-07-01

    The highly mobile two-dimensional electron system (2DES) on the surface of the insulating SrTiO{sub 3}(STO) offers exciting perspectives for advanced material design. This 2DES resides in a depletion layer caused by oxygen deficiency of the surface. With photoemission spectroscopy, we monitor the appearance of quasi-particle weight (QP) at the Fermi energy and oxygen vacancy induced states in the band gap (IG). Both, QP and IG weight, increase and decrease respectively upon exposure to extreme ultraviolet (XUV) light and in-situ oxygen dosing. By a proper adjustment of oxygen dosing, any intermediate state can be stabilized providing full control over the charge carrier density. From a comparison of the charge carrier concentrations obtained from an analysis of core-level spectra and the Fermi-surface volume, we conclude on a spatially inhomogeneous surface electronic structure with at least two different phases.

  4. Effect of Cleaving Temperature on the Surface and Bulk Fermi Surface of Sr2RuO4 Investigated by High Resolution Angle-Resolved Photoemission

    International Nuclear Information System (INIS)

    Liu Shan-Yu; Zhang Wen-Tao; Weng Hong-Ming; Zhao Lin; Liu Hai-Yun; Jia Xiao-Wen; Liu Guo-Dong; Dong Xiao-Li; Zhang Jun; Dai Xi; Fang Zhong; Zhou Xing-Jiang; Mao Zhi-Qiang; Chen Chuang-Tian; Xu Zu-Yan

    2012-01-01

    High resolution angle-resolved photoemission measurements are carried out to systematically investigate the effect of cleaving temperature on the electronic structures and Fermi surfaces of Sr 2 RuO 4 . Unlike previous reports, which found that a high cleaving temperature can suppress the surface Fermi surface, we find that the surface Fermi surface remains obvious and strong in Sr 2 RuO 4 cleaved at high temperature, even at room temperature. This indicates that cleaving temperature is not a key effective factor in suppressing surface bands. On the other hand, the bulk bands can be enhanced in an aged surface of Sr 2 RuO 4 that has been cleaved and held for a long time. We have also carried out laser ARPES measurements on Sr 2 RuO 4 by using a vacuum ultra-violet laser (photon energy at 6.994 eV) and found an obvious enhancement of bulk bands even for samples cleaved at low temperature. This information is important for realizing an effective approach to manipulating and detecting the surface and bulk electronic structure of Sr 2 RuO 4 . In particular, the enhancement of bulk sensitivity, along with the super-high instrumental resolution of VUV laser ARPES, will be advantageous in investigating fine electronic structure and superconducting properties of Sr 2 RuO 4 in the future. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

  5. Luminescence and surface properties of Tb3+ doped Sr3(VO4)2 nanophosphors

    International Nuclear Information System (INIS)

    Bedyal, A.K.; Kumar, Vinay; Sharma, Vishal

    2013-01-01

    In this paper, we present a detailed investigation of the luminescence and surface properties of Tb 3+ doped Sr 3 (VO 4 ) 2 nanocrystalline phosphors, synthesized by the combustion method. X-ray diffraction (XRD) peaks in the patterns corresponding to the reflection of rhombohedral pure phase of Sr 3 (VO 4 ) 2 . The average particle sizes have been found in the range of 30-34 nm. Scanning electron microscopy (SEM) indicated that an agglomerated peanut like morphology was obtained. Photoluminescence (PL) spectroscopy has been utilized to investigate the spectral properties of the phosphor. Under 237 nm excitation, it shows several bands centered at 487, 544, 588 and 624 nm, which result from 5 D 4 → 7 F J (J = 6, 5, 4 and 3) transitions of Tb 3+ , and the green emission band ( 5 D 4 → 7 F 5 ) located at 544 nm is dominant. The chemical states and homogeneous dopants' distribution in the host were analyzed with X-ray photoelectron spectroscopy (XPS) and time of flight-secondary ion mass spectroscopy (TOF-SIMS), respectively. A ToF-SIMS imaging shows an uniform distribution of Tb 3+ in the Sr 3 (VO 4 ) 2 . (author)

  6. Critical current density of BiSrCaCuO superconductors: effect of surface barriers

    International Nuclear Information System (INIS)

    Konczykowski, M.; Chikumoto, N.

    1992-01-01

    Effects of surface barriers on vortex motion in BiSrCaCuO-2212 high-temperature superconducting crystals is summarized. Characteristic features of this phenomenon appear in the hysteresis loop (shape of its ascending and descending branches), in the effect of 2.5 MeV electron irradiation, and in flux creep measurements (magnetization dependence to the crystal lateral dimension, size of the flux-creep barrier and the crossover as a function of temperature and time persistent current density). (A.B.). 25 refs., 3 figs

  7. Detection of low activities 90Sr and 137Cs in surface, subsoil and sewage waters

    International Nuclear Information System (INIS)

    Babenko, V.; Isaev, A.; Kazymyrova, G.; Rudyk, O.; Khristenko, U.

    2004-01-01

    In this article the methodic of detection of volumetric activity of radionuclide 90 Sr in surface, subsoil and sewage waters on the basis of measurement of counting samples using beta-spectrometers SEB-01, produced by RPE 'Atom Komplex Prylad' (RPE 'AKP') and mathematical proceeding of spectra by software packages AKWin. At that, the time of receiving of result shortens, comparing to method of radiochemistry, from 14 days to 3 days. Activity measurement range of beta-spectrometers SEB-01 is 0.1-10 4 Bq/l, that by corresponding radionuclides concentration, allows providing control of water objects according to national norms of Ukraine (2 Bq/l). (authors)

  8. Microscopic characterization of Fe nanoparticles formed on SrTiO3(001 and SrTiO3(110 surfaces

    Directory of Open Access Journals (Sweden)

    Miyoko Tanaka

    2016-06-01

    Full Text Available Fe nanoparticles grown on SrTiO3 (STO {001} and {110} surfaces at room temperature have been studied in ultrahigh vacuum by means of transmission electron microscopy and scanning tunnelling microscopy. It was shown that some Fe nanoparticles grow epitaxially. They exhibit a modified Wulff shape: nanoparticles on STO {001} surfaces have truncated pyramid shapes while those on STO {110} surfaces have hexagonal shapes. From profile-view TEM images, approximate values of the adhesion energy of the nanoparticles for both shapes are obtained.

  9. Surface phonons on Bi2Sr2CaCu2O8+δ

    International Nuclear Information System (INIS)

    Phelps, R.B.; Akavoor, P.; Kesmodel, L.L.; Demuth, J.E.; Mitzi, D.B.

    1993-01-01

    We report measurements of surface optical phonons on Bi 2 Sr 2 CaCu 2 O 8+δ with high-resolution electron-energy-loss spectroscopy (HREELS). In addition to peaks near 50 and 80 meV (403 and 645 cm -1 ), which have been previously observed, our loss spectra exhibit a peak at 26 meV (210 cm -1 ). Loss spectra were measured at temperatures from 45 to 146 K, and the temperature dependence of the peaks was found to be weak. The 50 and 80 meV peaks shift to lower frequency by ∼1.5 meV over this temperature range. All three peaks are attributed to surface optical phonons. The identification of particular bulk modes corresponding to the surface modes observed with HREELS is discussed

  10. Surface phonons on Bi2Sr2CaCu2O8+δ

    Science.gov (United States)

    Phelps, R. B.; Akavoor, P.; Kesmodel, L. L.; Demuth, J. E.; Mitzi, D. B.

    1993-11-01

    We report measurements of surface optical phonons on Bi2Sr2CaCu2O8+δ with high-resolution electron-energy-loss spectroscopy (HREELS). In addition to peaks near 50 and 80 meV (403 and 645 cm-1), which have been previously observed, our loss spectra exhibit a peak at 26 meV (210 cm-1). Loss spectra were measured at temperatures from 45 to 146 K, and the temperature dependence of the peaks was found to be weak. The 50 and 80 meV peaks shift to lower frequency by ~1.5 meV over this temperature range. All three peaks are attributed to surface optical phonons. The identification of particular bulk modes corresponding to the surface modes observed with HREELS is discussed.

  11. Native SrTiO3 (001) surface layer from resonant Ti L2,3 reflectance spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Valvidares, Manuel; Huijben, Mark; Yu, Pu; Ramesh, Ramamoorthy; Kortright, Jeffrey

    2010-11-03

    We quantitatively model resonant Ti L2,3 reflectivity Rs,p(q, hn) from several SrTiO3 (001) single crystals having different initial surface preparations and stored in ambient conditions before and between measurements. All samples exhibit unexpected 300 K Rs(hn) - Rp(hn) anisotropy corresponding to weak linear dichroism and tetragonal distortion of the TiO6 octahedra indicating a surface layer with properties different from cubic SrTiO3. Oscillations in Rs(q) confirm a ubiquitous surface layer 2-3 nm thick that evolves over a range of time scales. Resonant optical constant spectra derived from Rs,p(hn) assuming a uniform sample are refined using a single surface layer to fit measured Rs(q). Differences in surface layer and bulk optical properties indicate that the surface is significantly depleted in Sr and enriched in Ti and O. While consistent with the tendency of SrTiO3 surfaces toward non-stoichiometry, this layer does not conform simply to existing models for the near surface region and apparently forms via room temperature surface reactions with the ambient. This new quantitative spectral modeling approach is generally applicable and has potential to study near-surface properties of a variety of systems with unique chemical and electronic sensitivities.

  12. Quantum Chemical Study of Water Adsorption on the Surfaces of SrTiO3 Nanotubes.

    Science.gov (United States)

    Bandura, Andrei V; Kuruch, Dmitry D; Evarestov, Robert A

    2015-07-20

    We have studied the adsorption of water molecules on the inner and outer surfaces of nanotubes generated by rolling (001) layers of SrTiO3 cubic crystals. The stability and the atomic and electronic structures of the adsorbed layers are determined by using hybrid density functional theory. The absorption energy and the preferred adsorbate structure are essentially governed by the nature of the surface of the nanotube. Dissociative adsorption prevails on the outer nanotube surfaces. The stability of the adsorbed layers on the inner surfaces is related to the possibility of the formation of hydrogen bonds between water molecules and surface oxygen atoms, and depends on the surface curvature. The presence of water molecules on the inner surface of the nanotubes leads to an increase of the electronic band gap. Externally TiO2 -terminated nanotubes could be used for the photocatalytic decomposition of water by ultraviolet radiation. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  13. Modification of SrTiO3 single-crystalline surface after plasma flow treatment

    Energy Technology Data Exchange (ETDEWEB)

    Levin, Alexandr A.; Weissbach, Torsten; Leisegang, Tilmann; Meyer, Dirk C. [Institut fuer Strukturphysik, Technische Universitaet Dresden, 01062 Dresden (Germany); Kulagin, Nikolay A. [Kharkiv National University for Radioelectronics, av. Shakespeare 6-48, 61045 Kharkiv (Ukraine); Langer, Enrico [Institut fuer Festkoerperphysik, Technische Universitaet Dresden, 01062 Dresden (Germany)

    2009-07-01

    Surface of pure and transition metal-doped SrTiO3(STO) single crystals before and after hydrogen plasma-flow treatment (energy of 5..20 J/cm2) is investigated by wide-angle X-ray diffraction (WAXRD), fluorescence X-ray absorption near edge structure (XANES) and scanning electron microscopy (SEM) techniques. Plasma treatment results in the formation of a textured polycrystalline layer at the surface of the single-crystalline samples with different orientation. The formation of the quasi-ordered structures consisting of nanoscale-sized pyramids is observed by SEM. XANES evidences the change of the valency of the part of Ti4+ to Ti3+ due to the plasma treatment. The data obtained together with results of X-ray spectroscopy measurements gives evidences of the change of stoichiometry of the STO samples resulting in a change of their physical properties after plasma treatment.

  14. The surface structure of SrTiO3 at high temperatures under influence of oxygen

    International Nuclear Information System (INIS)

    Hesselberth, M. B. S.; Molen, S. J. van der; Aarts, J.

    2014-01-01

    We use low energy electron microscopy to investigate the structure of the SrTiO 3 (001) surface at elevated temperatures and different oxygen pressures. Upon varying the temperature between 500 °C and 900 °C in oxygen pressures ranging from 10 −9 millibar to 10 −4 millibar, two surface transitions are found to be present. The lower temperature (1 × 1) → (2 × 1) transition that is known to occur in ultrahigh vacuum can be reversed by increasing the oxygen pressure. At higher temperatures, we observe a (2 × 1) → disordered (1 × 1) transition which is irreversible in the experimental parameter range. The observations are expected to have a strong bearing on the growth of interface structures

  15. Portable instrumentation for quantitatively measuring radioactive surface contaminations, including 90Sr

    International Nuclear Information System (INIS)

    Brodzinski, R.L.

    1983-10-01

    In order to measure the effectiveness of decontamination efforts, a quantitative analysis of the radiocontamination is necessary, both before and after decontamination. Since it is desirable to release the decontaminated material for unrestricted use or disposal, the assay equipment must provide adequate sensitivity to measure the radioactivity at or below the release limit. In addition, the instrumentation must be capable of measuring all kinds of radiocontaminants including fission products, activation products, and transuranic materials. Finally, the survey instrumentation must be extremely versatile in order to assay the wide variety of contaminated surfaces in many environments, some of which may be extremely hostile or remote. This communication describes the development and application of portable instrumentation capable of quantitatively measuring most transuranics, activation products, and fission products, including 90 Sr, on almost any contaminated surface in nearly any location

  16. The geographic distribution of Sr isotopes from surface waters and soil extracts over the island of Bornholm (Denmark) – A base for provenance studies in archaeology and agriculture

    DEFF Research Database (Denmark)

    Frei, Robert; Frei, Karin Margarita

    2013-01-01

    In this paper we report the Sr isotope signatures, and Sr, Al and Na concentrations of 30 surface waters (lakes/ponds and rivers/creeks) and 19 soil sample extracts from the island of Bornholm (Denmark) and present a categorized 87Sr/86Sr value distribution map that may serve as a base...... for provenance studies, including archaeological migration and authenticity proof for particular food products. The Sr isotopic compositions of surface waters range from 87Sr/86Sr = 0.7097–0.7281 (average 0.7175 ± 0.0049; 1σ), whereas 0.1 M HNO3, 0.05 M HNO3, and 0.01 M CaCl2 soil extracts range from 87Sr/86Sr...... Sr isotope composition vs. Sr, Na and Al concentration relationships of soil extracts imply that lowering of the isotopic composition of leachable Sr on Bornholm results as a consequence of significant admixture to this fraction of Sr deposited as marine salts (aerosols), and that rainwater only has...

  17. Adsorption of UO22+ in surfaces of SrTiO3

    International Nuclear Information System (INIS)

    Ortiz O, H.B.; Ordonez R, E.; Fernandez V, S.M.

    2005-01-01

    The internationally accepted solution in the administration of the high level radioactive residuals is the multi barrier deep geologic storage which should guarantee that do not exist flights neither transfer of residuals to the atmosphere in time periods of at least 10,000 years. In this confinement type exists the interest to study materials that can be used as engineering barriers as well as the diverse interaction phenomena between these and the radionuclides. In this work it is presented the physicochemical characterization and evaluation of the surface properties and of adsorption of U(VI) in form of UO 2 (NO 3 ) 2 on the SrTiO 3 like possible candidate for contention barrier in the deep geologic confinement. The made studies showed that the SrTiO 3 is stable to temperatures between 0 and 800 C. At the same time it could settle down that the maximum sorption percentages are reached to near pH to the isoelectric point, where chemical species prevail in solution of the type UO 2 (X) - . (Author)

  18. Advancing the Frontiers in Nanocatalysis, Biointerfaces, and Renewable Energy Conversion by Innovations of Surface Techniques

    Energy Technology Data Exchange (ETDEWEB)

    Somorjai, G.A.; Frei, H.; Park, J.Y.

    2009-07-23

    The challenge of chemistry in the 21st century is to achieve 100% selectivity of the desired product molecule in multipath reactions ('green chemistry') and develop renewable energy based processes. Surface chemistry and catalysis play key roles in this enterprise. Development of in situ surface techniques such as high-pressure scanning tunneling microscopy, sum frequency generation (SFG) vibrational spectroscopy, time-resolved Fourier transform infrared methods, and ambient pressure X-ray photoelectron spectroscopy enabled the rapid advancement of three fields: nanocatalysts, biointerfaces, and renewable energy conversion chemistry. In materials nanoscience, synthetic methods have been developed to produce monodisperse metal and oxide nanoparticles (NPs) in the 0.8-10 nm range with controlled shape, oxidation states, and composition; these NPs can be used as selective catalysts since chemical selectivity appears to be dependent on all of these experimental parameters. New spectroscopic and microscopic techniques have been developed that operate under reaction conditions and reveal the dynamic change of molecular structure of catalysts and adsorbed molecules as the reactions proceed with changes in reaction intermediates, catalyst composition, and oxidation states. SFG vibrational spectroscopy detects amino acids, peptides, and proteins adsorbed at hydrophobic and hydrophilic interfaces and monitors the change of surface structure and interactions with coadsorbed water. Exothermic reactions and photons generate hot electrons in metal NPs that may be utilized in chemical energy conversion. The photosplitting of water and carbon dioxide, an important research direction in renewable energy conversion, is discussed.

  19. Mechanisms of desorption of 134Cs and 85Sr aerosols deposited on urban surfaces

    International Nuclear Information System (INIS)

    Real, J.; Persin, F.; Camarasa-Claret, C.

    2002-01-01

    The radioactive isotopes of cesium and strontium may be deposited on urban surfaces in the case of an accidental atmospheric discharge from a nuclear facility and thus imply a health hazard. In order to handle the decontamination of these surfaces, we have carried out experiments under controlled conditions on tiles and concrete and we have studied the physical and chemical mechanisms at the solid-liquid interface. The deposition of radionuclides was carried out in the form of aerosols indicating an accidental source term. Their desorption by rainwater is low in all cases, of the order of 5-6% for cesium for any material and 29 and 12% for strontium on tile and concrete, respectively. The low desorption values of cesium may be explained by the strong bonding that occurs with the silicates constituting the tile due to virtually irreversible processes of exchange of ions and by the formation of insoluble complexes with the C-S-H gel of concrete. The strontium-tile bonds are weaker, while strontium precipitates with the carbonates of concrete in the form of SrCO 3 . In view of these characteristics, washing solutions with high concentrations of chloride and oxalate of ammonium chosen for their ion-exchanging and sequestering properties were tested on these surfaces. The desorption of cesium improved strongly since it reached 70% on tile and 90% on concrete after 24 h of contact, which is consistent with our knowledge of the bonds between this element and the surfaces. Strontium, given the greater complexity of physical and chemical forms that it may take is less well desorbed. The ammonium chloride improves the desorption (50% and 40%, for tile and concrete, respectively) but the oxalate, while it does not affect desorption on the tiles, decreases that on the concrete since by strongly etching the concrete, it causes the release of carbonate ions that precipitate with strontium

  20. Bomb-test 90Sr in Pacific and Indian Ocean surface water as recorded by banded corals

    International Nuclear Information System (INIS)

    Toggweiler, J.R.; Trumbore, S.

    1985-01-01

    We report here measurements of bomb-test 90 Sr activity in the CaCO 3 skeletons of banded head forming corals collected from nine locations in the tropical Pacific and Indian Oceans. Density variations in skeletal carbonate demarcate annual growth bands and allow one to section individual years. Measurements of 90 Sr activity in the annual bands reconstruct the activity of the water in which the coral grew. Our oldest records date to the early years of the nuclear era and record not only fallout deposition from the major U.S. and Soviet tests of 1958-1962, but also the huge, and largely unappreciated, localized inputs from the U.S. tests at Eniwetok and Bikini atolls during 1952-1958. In the 1960's the 90 Sr activity in Indian Ocean surface water was twice as high as activity levels in the South Pacific at comparable latitudes. We suggest that substantial amounts of northern hemisphere fallout moved west and south into the Indian Ocean via passages through the Indonesian archipelago. Equatorial Pacific 90 Sr levels have remained relatively constant from the mid 1960's through the end of 1970's in spite of 90 Sr decay, reflecting a large-scale transfer of water between the temperate and tropical North Pacific. Activity levels at Fanning Is. (4 0 N, 160 0 W) appear to vary in conjunction with the 3-4 year El Nino cycle. (orig.)

  1. Plasma-Assisted Synthesis and Surface Modification of Electrode Materials for Renewable Energy.

    Science.gov (United States)

    Dou, Shuo; Tao, Li; Wang, Ruilun; El Hankari, Samir; Chen, Ru; Wang, Shuangyin

    2018-02-14

    Renewable energy technology has been considered as a "MUST" option to lower the use of fossil fuels for industry and daily life. Designing critical and sophisticated materials is of great importance in order to realize high-performance energy technology. Typically, efficient synthesis and soft surface modification of nanomaterials are important for energy technology. Therefore, there are increasing demands on the rational design of efficient electrocatalysts or electrode materials, which are the key for scalable and practical electrochemical energy devices. Nevertheless, the development of versatile and cheap strategies is one of the main challenges to achieve the aforementioned goals. Accordingly, plasma technology has recently appeared as an extremely promising alternative for the synthesis and surface modification of nanomaterials for electrochemical devices. Here, the recent progress on the development of nonthermal plasma technology is highlighted for the synthesis and surface modification of advanced electrode materials for renewable energy technology including electrocatalysts for fuel cells, water splitting, metal-air batteries, and electrode materials for batteries and supercapacitors, etc. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  2. Surface properties and catalytic performance of Pt/LaSrCoO4 catalysts in the oxidation of hexane

    Directory of Open Access Journals (Sweden)

    Hua Zhong

    2007-08-01

    Full Text Available Perovskite-type La2 –xSrxCoO4 mixed oxides have been prepared by calcination at various temperatures of precipitates obtained from aqueous solutions in the presence of citric or ethylenediamintetraacetic (EDTA acids, and have been studied by X-ray diffraction (XRD, surface area (BET measurements, temperature programmed desorption (TPD, temperature programmed reduction (TPR and X-ray photoelectron spectroscopy (XPS. These oxides are catalysts for hexane oxidation, with the greatest activity for LaSrCoO4 calcined at 750 C. This has extensive oxygen vacancies and large internal surface area. Pt-modified LaSrCoO4 catalysts are significantly more active than the Pt-free system. Both surface and bulk phases of the preovskitetype oxides contribute to hexane oxidation.

  3. First-principles study of the (001) surface of cubic Ba{sub 0.5}Sr{sub 0.5}TiO{sub 3}

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Yuan Xu [Computational Materials Science Center, National Institute for Materials Science, Tsukuba 305-0044 (Japan); Institute for Computational Materials Science, School of Physics and Electronics, Henan University, Kaifeng 475004 (China)

    2008-06-15

    We have theoretically investigated basic properties of the (001) surface of cubic Ba{sub 0.5}Sr{sub 0.5}TiO{sub 3} (BST) by the plane-wave pseudopotential method within the local-density approximation. For the BaSrO{sub 2}-terminated surface, the surface-layer Sr atoms move inward and the surface-layer Ba atoms move outward. Moreover, the displacement of the surface-layer Sr atoms is much larger than the surface-layer Ba atoms. The rumpling of the BaSrO{sub 2}-terminated surface is much larger than that of the Ti{sub 2}O{sub 4}-terminated one. The surface state appears in the band structure of the Ti{sub 2}O{sub 4}-terminated surface of BST. Based on the results of the calculated grand thermodynamic potential, only the BaSrO{sub 2}-terminated surface can exist in the (001) surface of cubic BST. (copyright 2008 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  4. First-principles study of the (001) surface of cubic Ba0.5Sr0.5TiO3

    International Nuclear Information System (INIS)

    Wang, Yuan Xu

    2008-01-01

    We have theoretically investigated basic properties of the (001) surface of cubic Ba 0.5 Sr 0.5 TiO 3 (BST) by the plane-wave pseudopotential method within the local-density approximation. For the BaSrO 2 -terminated surface, the surface-layer Sr atoms move inward and the surface-layer Ba atoms move outward. Moreover, the displacement of the surface-layer Sr atoms is much larger than the surface-layer Ba atoms. The rumpling of the BaSrO 2 -terminated surface is much larger than that of the Ti 2 O 4 -terminated one. The surface state appears in the band structure of the Ti 2 O 4 -terminated surface of BST. Based on the results of the calculated grand thermodynamic potential, only the BaSrO 2 -terminated surface can exist in the (001) surface of cubic BST. (copyright 2008 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  5. Surface characterization, in vitro and in vivo biocompatibility of Mg-0.3Sr-0.3Ca for temporary cardiovascular implant

    Energy Technology Data Exchange (ETDEWEB)

    Bornapour, M., E-mail: mandana.bornapour@mail.mcgill.ca [Light Metals and Advanced Magnesium Materials, Mining and Materials Engineering, McGill University, Montreal, Qc, H3A 0C5 (Canada); Biointerface Lab, Mining and Materials Engineering, McGill University, Montreal, Qc H3A 0C5 (Canada); Mahjoubi, H. [Biointerface Lab, Mining and Materials Engineering, McGill University, Montreal, Qc H3A 0C5 (Canada); Vali, H. [Department of Anatomy and Cell Biology, McGill University, Montreal, Qc, H3A 0C7 (Canada); Shum-Tim, D. [Department of Cardiac Surgery and Surgical Research, McGill University, Montreal, Qc H3G 1A1 (Canada); Cerruti, M. [Biointerface Lab, Mining and Materials Engineering, McGill University, Montreal, Qc H3A 0C5 (Canada); Pekguleryuz, M. [Light Metals and Advanced Magnesium Materials, Mining and Materials Engineering, McGill University, Montreal, Qc, H3A 0C5 (Canada)

    2016-10-01

    Magnesium-based alloys are attractive candidate materials for medical applications. Our earlier work showed that the ternary Mg-0.3Sr-0.3Ca alloy exhibits slower degradation rates than both binary Mg-Sr and Mg-Ca alloys. The ternary alloy immersed in simulated body fluid (SBF) forms a compact surface layer of corrosion products that we hypothesized to be a Sr-substituted hydroxyapatite (HA). The main objectives of the current work are to understand the bio-degradation mechanism of Mg-0.3Sr-0.3Ca, to identify the exact nature of its protective layer and to evaluate the in vitro and in vivo biocompatibility of the alloy for cardiovascular applications. To better simulate the physiological environment, the alloy was immersed in SBF which was daily refreshed. Raman spectroscopy and X-Ray photoelectron spectroscopy (XPS) confirmed the formation of a thin, Sr-substituted HA layer at the interface between the alloy and the corrosion products. In vitro biocompatibility evaluated via indirect cytotoxicity assays using HUVECs showed no toxicity effect and ions extracted from Mg-0.3Sr-0.3Ca in fact increased the viability of HUVECs after one week. In vivo tests were performed by implanting a tubular Mg-0.3Sr-0.3Ca stent along with a WE43 control stent into the right and left femoral artery of a dog. Post implantation and histological analyses showed no thrombosis in the artery with Mg-0.3Sr-0.3Ca stent after 5 weeks of implantation while the artery implanted with WE43 stent was extensively occluded and thrombosed. Microscopic observation of the Mg-0.3Sr-0.3Ca implant-tissue interface confirmed the in situ formation of Sr-substituted HA on the surface during in vivo test. These results show that the interfacial layer protects the surface of the Mg-0.3Sr-0.3Ca alloy both in vitro and in vivo, and is the key factor in the bio-corrosion resistance of the alloy. - Highlights: • The surface active elements of Sr and Ca alter the corrosion of Mg alloy in SBF • Sr

  6. Surface characterization, in vitro and in vivo biocompatibility of Mg-0.3Sr-0.3Ca for temporary cardiovascular implant

    International Nuclear Information System (INIS)

    Bornapour, M.; Mahjoubi, H.; Vali, H.; Shum-Tim, D.; Cerruti, M.; Pekguleryuz, M.

    2016-01-01

    Magnesium-based alloys are attractive candidate materials for medical applications. Our earlier work showed that the ternary Mg-0.3Sr-0.3Ca alloy exhibits slower degradation rates than both binary Mg-Sr and Mg-Ca alloys. The ternary alloy immersed in simulated body fluid (SBF) forms a compact surface layer of corrosion products that we hypothesized to be a Sr-substituted hydroxyapatite (HA). The main objectives of the current work are to understand the bio-degradation mechanism of Mg-0.3Sr-0.3Ca, to identify the exact nature of its protective layer and to evaluate the in vitro and in vivo biocompatibility of the alloy for cardiovascular applications. To better simulate the physiological environment, the alloy was immersed in SBF which was daily refreshed. Raman spectroscopy and X-Ray photoelectron spectroscopy (XPS) confirmed the formation of a thin, Sr-substituted HA layer at the interface between the alloy and the corrosion products. In vitro biocompatibility evaluated via indirect cytotoxicity assays using HUVECs showed no toxicity effect and ions extracted from Mg-0.3Sr-0.3Ca in fact increased the viability of HUVECs after one week. In vivo tests were performed by implanting a tubular Mg-0.3Sr-0.3Ca stent along with a WE43 control stent into the right and left femoral artery of a dog. Post implantation and histological analyses showed no thrombosis in the artery with Mg-0.3Sr-0.3Ca stent after 5 weeks of implantation while the artery implanted with WE43 stent was extensively occluded and thrombosed. Microscopic observation of the Mg-0.3Sr-0.3Ca implant-tissue interface confirmed the in situ formation of Sr-substituted HA on the surface during in vivo test. These results show that the interfacial layer protects the surface of the Mg-0.3Sr-0.3Ca alloy both in vitro and in vivo, and is the key factor in the bio-corrosion resistance of the alloy. - Highlights: • The surface active elements of Sr and Ca alter the corrosion of Mg alloy in SBF • Sr

  7. Synthesis, surface structure and optical properties of double perovskite Sr{sub 2}NiMoO{sub 6} nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Lei; Wan, Yingpeng [State and Local Joint Engineering Laboratory for Novel Functional Polymeric Materials, College of Chemistry, Chemical Engineering and Materials Science, Soochow University, Suzhou, 215123 (China); Xie, Hongde, E-mail: xiehongde@suda.edu.cn [State and Local Joint Engineering Laboratory for Novel Functional Polymeric Materials, College of Chemistry, Chemical Engineering and Materials Science, Soochow University, Suzhou, 215123 (China); Huang, Yanlin; Yang, Li [State and Local Joint Engineering Laboratory for Novel Functional Polymeric Materials, College of Chemistry, Chemical Engineering and Materials Science, Soochow University, Suzhou, 215123 (China); Qin, Lin [Department of Physics and Interdisciplinary Program of Biomedical, Mechanical & Electrical Engineering, Pukyong National University, Busan, 608-737 (Korea, Republic of); Seo, Hyo Jin, E-mail: hjseo@pknu.ac.kr [Department of Physics and Interdisciplinary Program of Biomedical, Mechanical & Electrical Engineering, Pukyong National University, Busan, 608-737 (Korea, Republic of)

    2016-12-15

    Highlights: • Double perovskite Sr{sub 2}NiMoO{sub 6} nanoparticles were prepared via sol-gel route. • The nanoparticles have efficient optical absorption in visible light. • The band structure and energy positions were determined. • The perovskite has efficient photocatalytic on RhB photodegradation. • Multivalent Mo and Ni-ions on the surfaces were investigated. - Abstract: Double perovskite Sr{sub 2}NiMoO{sub 6} nanoparticles were synthesized via the chemical sol-gel route. The phase formation was investigated through X-ray polycrystalline diffraction (XRD) and Rietveld refinements. The perovskite crystallized in worm-like nano-grains with the diameter of 20–50 nm. The optical properties were measured by the optical absorption spectra. The nanoparticles present an indirect allowed transition with a narrow band gap of 2.1 eV. Sr{sub 2}NiMoO{sub 6} nanoparticles have obvious photocatalytic ability on the degradation of Rhodamine B (RhB) solutions under the irradiation of visible light. The transport behaviors of the excitons were investigated from the photoluminescence spectra and the corresponding decay lifetimes. Sr{sub 2}NiMoO{sub 6} nanoparticles present several advantages for photocatalysis such as the appropriate band energy positions, the quenched luminescence, and the coexistence of multivalent ions in the lattices.

  8. Sea Surface Temperature Records Using Sr/Ca Ratios in a Siderastrea siderea Coral from SE Cuba

    Science.gov (United States)

    Fargher, H. A.; Hughen, K. A.; Ossolinski, J. E.; Bretos, F.; Siciliano, D.; Gonzalez, P.

    2015-12-01

    Sea surface temperature (SST) variability from Cuba remains relatively unknown compared to the rest of the Caribbean. Cuba sits near an inflection point in the spatial pattern of SST from the North Atlantic Oscillation (NAO), and long SST records from the region could reveal changes in the influence of this climate system through time. A Siderastrea siderea coral from the Jardínes de la Reina in southern Cuba was drilled to obtain a 220 year long archive of environmental change. The genus Siderastrea has not been extensively studied as an SST archive, yet Sr/Ca ratios in the Cuban core show a clear seasonal signal and strong correlation to instrumental SST data (r2 = 0.86 and 0.36 for monthly and interannual (winter season) timescales, respectively). Annual growth rates (linear extension) of the coral are observed to have a minor influence on Sr/Ca variability, but do not show a direct correlation to SST on timescales from annual to multidecadal. Sr/Ca measurements from the Cuban coral are used to reconstruct monthly and seasonal (winter, summer) SST extending back more than two centuries. Wintertime SST in southern Cuba is compared to other coral Sr/Ca records of winter-season SST from locations sensitive to the NAO in order to investigate the stationarity of the NAO SST 'fingerprint' through time.

  9. Characterizing multiple sources and interaction in the critical zone through Sr-isotope tracing of surface and groundwater

    Science.gov (United States)

    Negrel, Philippe; Pauwels, Hélène

    2017-04-01

    The Critical Zone (CZ) is the lithosphere-atmosphere boundary where complex physical, chemical and biological processes occurs and control the transfer and storage of water and chemical elements. This is the place where life-sustaining resources are, where nutrients are being released from the rocks. Because it is the place where we are living, this is a fragile zone, a critical zone as a perturbed natural ecosystem. Water resources in hard-rocks commonly involve different hydrogeological compartments such as overlying sediments, weathered rock, the weathered-fissured zone, and fractured bedrock. Streams, lakes and wetlands that drain such environments can drain groundwater, recharge groundwater, or do both. Groundwater resources in many countries are increasingly threatened by growing demand, wasteful use, and contamination. Surface water and shallow groundwater are particularly vulnerable to pollution, while deeper resources are more protected from contamination. Here, we first report on Sr isotope data as well as major ions, from shallow and deep groundwater in several granite and schist areas over France with intensive agriculture covering large parts of these catchments. In three granite and Brioverian 'schist' areas of the Armorican Massif, the range in Sr contents in groundwater from different catchments agrees with previous work on groundwater sampled from granites in France. The Sr content is well correlated with Mg and both are partly related to agricultural practices and water rock interaction. The relationship between Sr- isotope and Mg/Sr ratios allow defining the different end-members, mainly rain, agricultural practice and water-rock interaction. The data from the Armorican Massif and other surface and groundwater for catchment draining silicate bedrocks (300-450Ma) like the Hérault, Seine, Moselle, Garonne, Morvan, Margeride, Cantal, Pyrénées and Vosges are scattered between at least three geochemical signatures. These include fertilizer and

  10. Conceptual and numerical modelling of radionuclide transport in near-surface systems at Forsmark. SR-Site Biosphere

    International Nuclear Information System (INIS)

    Pique, Angels; Grandia, Fidel; Sena, Clara; Arcos, David; Molinero, Jorge; Duro, Lara; Bruno, Jordi

    2010-11-01

    In the framework of the SR-Site safety assessment, a conceptual and numerical modelling of radionuclide reactive transport in near-surface systems (including till and clay systems) at Forsmark has been carried out. The objective was to evaluate the retention capacity of the near-surface systems, composed of Quaternary deposits, which would be the last natural barrier for an eventual radionuclide release from the deep repository prior to reaching the biosphere. The studied radionuclides are 14 C, 129 I, 36 Cl, 94 Nb, 59 Ni, 93 Mo, 79 Se, 99 Tc, 230 Th, 90 Sr, 226 Ra, 135 Cs and U. Conceptual description and numerical simulations of radionuclide reactive transport show that cation exchange and surface complexation on illite are active processes for the retention of several radionuclides (U, Th, Ni, Cs, Sr, Ra). Surface complexation on iron hydroxide is an active process in the till system, able to effectively retain U and Ni. Another retention process of importance is the incorporation of the radionuclides into mineral phases, either by the precipitation of pure phases or solid solutions. Quantitative modelling has been useful to illustrate the incorporation of C and Sr in the carbonate solid solution in the considered model domains (till and clay), as well as the precipitation of uraninite in the clay sediments and the precipitation of native selenium and radiobarite in the till. Other mineral phases that could, a priori, retain U, Se, Nb and Tc do not precipitate in the simulations, either due to the pH-Eh conditions and/or because the dissolved concentration of the element is not high enough under the considered simulation conditions. It is important to keep in mind that changes in these parameters and in the boundary conditions could modify the predicted behaviour of these elements. The radionuclides that are most significantly retarded are Th, Ni and Cs, mainly through sorption onto illite. Therefore, if the amount of illite (or available sorption sites

  11. Adsorption and Electronic Structure of Sr and Ag Atoms on Graphite Surfaces: a First-Principles Study

    Science.gov (United States)

    Luo, Xiao-Feng; Fang, Chao; Li, Xin; Lai, Wen-Sheng; Sun, Li-Feng; Liang, Tong-Xiang

    2013-06-01

    The adsorption behaviors of radioactive strontium and silver nuclides on the graphite surface in a high-temperature gas-cooled reactor are studied by first-principles theory using generalized gradient approximation (GGA) and local density approximation (LDA) pseudo-potentials. It turns out that Sr prefers to be absorbed at the hollow of the carbon hexagonal cell by 0.54 eV (GGA), while Ag likes to sit right above the carbon atom with an adsorption energy of almost zero (GGA) and 0.45 eV (LDA). Electronic structure analysis reveals that Sr donates its partial electrons of the 4p and 5s states to the graphite substrate, while Ag on graphite is a physical adsorption without any electron transfer.

  12. Conceptual and numerical modelling of radionuclide transport in near-surface systems at Forsmark. SR-Site Biosphere

    Energy Technology Data Exchange (ETDEWEB)

    Pique, Angels; Grandia, Fidel; Sena, Clara; Arcos, David; Molinero, Jorge; Duro, Lara; Bruno, Jordi (Amphos21 Consulting S.L., Barcelona (Spain))

    2010-11-15

    In the framework of the SR-Site safety assessment, a conceptual and numerical modelling of radionuclide reactive transport in near-surface systems (including till and clay systems) at Forsmark has been carried out. The objective was to evaluate the retention capacity of the near-surface systems, composed of Quaternary deposits, which would be the last natural barrier for an eventual radionuclide release from the deep repository prior to reaching the biosphere. The studied radionuclides are 14C, 129I, 36Cl, 94Nb, 59Ni, 93Mo, 79Se, 99Tc, 230Th, 90Sr, 226Ra, 135Cs and U. Conceptual description and numerical simulations of radionuclide reactive transport show that cation exchange and surface complexation on illite are active processes for the retention of several radionuclides (U, Th, Ni, Cs, Sr, Ra). Surface complexation on iron hydroxide is an active process in the till system, able to effectively retain U and Ni. Another retention process of importance is the incorporation of the radionuclides into mineral phases, either by the precipitation of pure phases or solid solutions. Quantitative modelling has been useful to illustrate the incorporation of C and Sr in the carbonate solid solution in the considered model domains (till and clay), as well as the precipitation of uraninite in the clay sediments and the precipitation of native selenium and radiobarite in the till. Other mineral phases that could, a priori, retain U, Se, Nb and Tc do not precipitate in the simulations, either due to the pH-Eh conditions and/or because the dissolved concentration of the element is not high enough under the considered simulation conditions. It is important to keep in mind that changes in these parameters and in the boundary conditions could modify the predicted behaviour of these elements. The radionuclides that are most significantly retarded are Th, Ni and Cs, mainly through sorption onto illite. Therefore, if the amount of illite (or available sorption sites) decreases, the

  13. [Studies on a sequential injection renewable surface reflectance spectrophotometric system using a microchip flow cell].

    Science.gov (United States)

    Wang, Jian-ya; Fang, Zhao-lun

    2002-02-01

    A microchip flow cell was developed for flow injection renewable surface assay by reflectance spectrophotometry. The flow cell was coupled to a sequential injection system and optical fiber photometric detection system. The flow cell featured a three-layer structure. The flow channel was cut into a silicone rubber membrance which formed the middle layer, and a porous filter was inlayed across a widened section of the channel to trap microbeads introduced into the flow cell. The area of the detection window of the flow cell was approximately 3.6 mm2, the volume of the bead trapped in the flow cell was 2.2 microL, the depth of the bead layer was 600 microns. A multistrand bifurcated optical fiber was coupled with incident light, detector and flow cell. The chromogenic reaction of Cr(VI) with 1,5-diphenylcarbohydrazide (DPC) which was adsorbed on trapped Polysorb C-18 beads was used as a model reaction to optimize the flow cell design and the experimental system. The reflectance of the renewable reaction surface was monitored at 540 nm. With 100 microL sample loaded and 1.0 mL.min-1 carrier flow rate, the linear response range was 0-0.6 microgram.mL-1 Cr(VI). A detection limit (3 sigma) of 6 ng.mL-1, precision of 1.5% RSD(n = 11), and a throughput of 64 samples per hour were achieved. Considerations in system and flow cell design, the influence of depth of the bead layer, weight of beads used, and the flow rates of carrier stream on the performance were discussed.

  14. Electronic structure and topography of annealed SrTiO3(1 1 1) surfaces studied with MIES and STM

    International Nuclear Information System (INIS)

    Goemann, Anissa; Goemann, Karsten; Frerichs, Martin; Kempter, Volker; Borchardt, Guenter; Maus-Friedrichs, Wolfgang

    2005-01-01

    Perovskites of ABO 3 type like strontium titanate (SrTiO 3 ) are of great practical concern as materials for oxygen sensors operating at high temperatures. It is well known that the surface layer shows different properties compared to the bulk. Numerous studies exist for the SrTiO 3 (1 0 0) and (1 1 0) surfaces which have investigated the changes in the electronic structure and topography as a function of the preparation conditions. They have indicated a rather complex behaviour of the surface and the near surface region of SrTiO 3 at elevated temperatures. Up to now, the behaviour of the SrTiO 3 (1 1 1) surfaces under thermal treatment is not sufficiently known. This contribution is intended to work out the relation between alteration of the surface topography with respect to the preparation conditions and the simultaneous changes of the electronic structure. We applied scanning tunneling microscopy (STM) to investigate the surface topography and, additionally, metastable impact electron spectroscopy (MIES) to study the surface electronic structure of reconstructed SrTiO 3 (1 1 1) surfaces. The crystals were heated up to 1000 deg. C under reducing and oxidizing conditions. Both preparation conditions cause strong changes of the surface topography and electronic structure. A microfaceting of the topmost layers is found

  15. Surface characterization of colossal magnetoresistive manganites La1-xSr xMnO3 using photoelectron spectroscopy

    International Nuclear Information System (INIS)

    Mannella, N.; Rosenhahn, A.; Nambu, A.; Sell, B.C.; Mun, B.S.; Yang, S.-H.; Marchesini, S.; Watanabe, M.; Ibrahim, K.; Ritchey, S.B.; Tomioka, Y.; Fadley, C.S.

    2006-01-01

    We have studied the temperature and time dependence of Surface chemical composition and atomic structure of in situ fractured colossal magnetoresistive perovskites La 1-x Sr x MnO (x = 0.3, 0.4) using core-level photoelectron spectroscopy and diffraction, simultaneous with observing marked changes in both core and valence electronic structure on going above the Curie temperature [N. Mannella et al., Phys. Rev. Lett. 92 (2004) 166401]. Stoichiometric analyses via core-level intensity ratios show that the near-surface composition is very nearly the same as that of the nominal (bulk) stoichiometry and further show that, during duration of our experiments, the degree of surface stoichiometry alteration or contamination has been minimal. The effects of photoelectron diffraction on such analyses are also explored. We comment on the degree to which near-surface composition or atomic-structure alterations might influence spectroscopic investigations of these manganites, or other strongly correlated materials

  16. Intermediate surface structure between step bunching and step flow in SrRuO3 thin film growth

    Science.gov (United States)

    Bertino, Giulia; Gura, Anna; Dawber, Matthew

    We performed a systematic study of SrRuO3 thin films grown on TiO2 terminated SrTiO3 substrates using off-axis magnetron sputtering. We investigated the step bunching formation and the evolution of the SRO film morphology by varying the step size of the substrate, the growth temperature and the film thickness. The thin films were characterized using Atomic Force Microscopy and X-Ray Diffraction. We identified single and multiple step bunching and step flow growth regimes as a function of the growth parameters. Also, we clearly observe a stronger influence of the step size of the substrate on the evolution of the SRO film surface with respect to the other growth parameters. Remarkably, we observe the formation of a smooth, regular and uniform ``fish skin'' structure at the transition between one regime and another. We believe that the fish skin structure results from the merging of 2D flat islands predicted by previous models. The direct observation of this transition structure allows us to better understand how and when step bunching develops in the growth of SrRuO3 thin films.

  17. Biodegradable polyester films from renewable aleuritic acid: surface modifications induced by melt-polycondensation in air

    International Nuclear Information System (INIS)

    Benítez, José Jesús; De Vargas-Parody, María Inmaculada; Cruz-Carrillo, Miguel Antonio; Heredia-Guerrero, José Alejandro; Morales-Flórez, Victor; De la Rosa-Fox, Nicolás; Heredia, Antonio

    2016-01-01

    Good water barrier properties and biocompatibility of long-chain biopolyesters like cutin and suberin have inspired the design of synthetic mimetic materials. Most of these biopolymers are made from esterified mid-chain functionalized ω-long chain hydroxyacids. Aleuritic (9,10,16-trihydroxypalmitic) acid is such a polyhydroxylated fatty acid and is also the major constituent of natural lac resin, a relatively abundant and renewable resource. Insoluble and thermostable films have been prepared from aleuritic acid by melt-condensation polymerization in air without catalysts, an easy and attractive procedure for large scale production. Intended to be used as a protective coating, the barrier's performance is expected to be conditioned by physical and chemical modifications induced by oxygen on the air-exposed side. Hence, the chemical composition, texture, mechanical behavior, hydrophobicity, chemical resistance and biodegradation of the film surface have been studied by attenuated total reflection–Fourier transform infrared spectroscopy (ATR–FTIR), atomic force microscopy (AFM), nanoindentation and water contact angle (WCA). It has been demonstrated that the occurrence of side oxidation reactions conditions the surface physical and chemical properties of these polyhydroxyester films. Additionally, the addition of palmitic acid to reduce the presence of hydrophilic free hydroxyl groups was found to have a strong influence on these parameters. (paper)

  18. Fermi Surface of Sr_{2}RuO_{4}: Spin-Orbit and Anisotropic Coulomb Interaction Effects.

    Science.gov (United States)

    Zhang, Guoren; Gorelov, Evgeny; Sarvestani, Esmaeel; Pavarini, Eva

    2016-03-11

    The topology of the Fermi surface of Sr_{2}RuO_{4} is well described by local-density approximation calculations with spin-orbit interaction, but the relative size of its different sheets is not. By accounting for many-body effects via dynamical mean-field theory, we show that the standard isotropic Coulomb interaction alone worsens or does not correct this discrepancy. In order to reproduce experiments, it is essential to account for the Coulomb anisotropy. The latter is small but has strong effects; it competes with the Coulomb-enhanced spin-orbit coupling and the isotropic Coulomb term in determining the Fermi surface shape. Its effects are likely sizable in other correlated multiorbital systems. In addition, we find that the low-energy self-energy matrix-responsible for the reshaping of the Fermi surface-sizably differs from the static Hartree-Fock limit. Finally, we find a strong spin-orbital entanglement; this supports the view that the conventional description of Cooper pairs via factorized spin and orbital part might not apply to Sr_{2}RuO_{4}.

  19. Studies on Gas Sensing Performance of Pure and Surface Modified SrTiO3 Thick Film Resistors

    Directory of Open Access Journals (Sweden)

    V. B. Gaikwad

    2009-08-01

    Full Text Available Strontium Titanate (SrTiO3 (ST was prepared mechanochemically from Sr(OH2 and TiO2. XRD confirms the Perovskite phase of material. Thick films of ST were prepared by screen-printing technique. The gas sensing performances of thick films were tested for various gases. It showed maximum sensitivity to CO gas at 350 oC for 100 ppm gas concentration. To improve the sensitivity and selectivity of the film towards a particular gas, ST thick films were surface modified by dipping them in a solution of nano copper for different intervals of time. These surface modified ST films showed larger sensitivity to H2S gas (100 ppm at 300 oC than pure ST film. A systematic study, of sensing performance of the sensor, indicates the key role-played by the nano copper species on the surface .The sensitivity, selectivity, response and recovery time of the sensor were measured and presented.

  20. Spin polarized electronic states and spin textures at the surface of oxygen-deficient SrTiO3

    Science.gov (United States)

    Jeschke, Harald O.; Altmeyer, Michaela; Rozenberg, Marcelo; Gabay, Marc; Valenti, Roser

    We investigate the electronic structure and spin texture at the (001) surface of SrTiO3 in the presence of oxygen vacancies by means of ab initio density functional theory (DFT) calculations of slabs. Relativistic non-magnetic DFT calculations exhibit Rashba-like spin winding with a characteristic energy scale ~ 10 meV. However, when surface magnetism on the Ti ions is included, bands become spin-split with an energy difference ~ 100 meV at the Γ point. This energy scale is comparable to the observations in SARPES experiments performed on the two-dimensional electronic states confined near the (001) surface of SrTiO3. We find the spin polarized state to be the ground state of the system, and while magnetism tends to suppress the effects of the relativistic Rashba interaction, signatures of it are still clearly visible in terms of complex spin textures. We gratefully acknowledge financial support from the Deutsche Forschungsgemeinschaft through grants SFB/TR 49 and FOR 1346.

  1. Multi-species coral Sr/Ca-based sea-surface temperature reconstruction using Orbicella faveolata and Siderastrea siderea from the Florida Straits

    Science.gov (United States)

    Flannery, Jennifer A.; Richey, Julie N.; Thirumalai, Kaustubh; Poore, Richard Z.; DeLong, Kristine L.

    2017-01-01

    We present new, monthly-resolved Sr/Ca-based sea-surface temperature (SST) records from two species of massive coral, Orbicella faveolata and Siderastrea siderea, from the Dry Tortugas National Park, FL, USA (DTNP). We combine these new records with published data from three additional S. siderea coral colonies to generate a 278-year long multi-species stacked Sr/Ca-SST record from DTNP. The composite record of mean annual Sr/Ca-SST at DTNP shows pronounced decadal-scale variability with a range of 1 to 2°C. Notable cool intervals in the Sr/Ca-derived SST lasting about a decade centered at ~1845, ~1935, and ~1965 are associated with reduced summer Sr/Ca-SST (monthly maxima < 29°C), and imply a reduction in the spatial extent of the Atlantic Warm Pool (AWP). There is significant coherence between the composite DTNP Sr/Ca-SST record and the Atlantic Multidecadal Oscillation (AMO) index, with the AMO lagging Sr/Ca-SST at DTNP by 9 years. Low frequency variability in the Gulf Stream surface transport, which originates near DTNP, may provide a link for the lagged relationship between multidecadal variability at DTNP and the AMO.

  2. A heat transfer correlation based on a surface renewal model for molten core concrete interaction study

    International Nuclear Information System (INIS)

    Tourniaire, B. . E-mail bruno.tourniaire@cea.fr

    2006-01-01

    The prediction of heat transfer between corium pool and concrete basemat is of particular significance in the framework of the study of PWR's severe accident. Heat transfer directly governs the ablation velocity of concrete in case of molten core concrete interaction (MCCI) and, consequently, the time delay when the reactor cavity may fail. From a restricted hydrodynamic point of view, this issue is related to heat transfer between a heated bubbling pool and a porous wall with gas injection. Several experimental studies have been performed with simulant materials and many correlations have been provided to address this issue. The comparisons of the results of these correlations with the measurements and their extrapolation to reactor materials show that strong discrepancies between the results of these models are obtained which probably means that some phenomena are not well taken into account. The main purpose of this paper is to present an alternative heat transfer model which was originally developed for chemical engineering applications (bubble columns) by Deckwer. A part of this work is devoted to the presentation of this model, which is based on a surface renewal assumption. Comparison of the results of this model with available experimental data in different systems are presented and discussed. These comparisons clearly show that this model can be used to deal with the particular problem of MCCI. The analyses also lead to enrich the original model by taking into account the thermal resistance of the wall: a new formulation of the Deckwer's correlation is finally proposed

  3. The water adsorption on the surfaces of SrMO{sub 3} (M= Ti, Zr, and Hf) crystalline oxides: quantum and classical modelling

    Energy Technology Data Exchange (ETDEWEB)

    Evarestov, R A; Bandura, A V; Blokhin, E N [Department of Quantum Chemistry, St. Petersburg State University 26 University Ave., Petergoff, St. Petersburg, 198504 (Russian Federation)

    2007-12-15

    Hybrid HF-DFT LCAO simulations of (001) surface properties and water adsorption on cubic SrTiO{sub 3}, SrZrO{sub 3}, and SrHfO{sub 3} perovskites are performed in a single-slab model framework. The optimized atomic structures and water adsorption energies have been calculated for a single water molecule per the surface unit cell. The possibility of the water molecular dissociation was investigated. Basing on the experimental data and results of the ab initio calculations the new interatomic potentials have been developed to describe the bulk and surface properties of the binary and ternary titanium and zirconium oxides. The proposed force-field takes into account the polarization effects via the shell model. The force-field suggested was used in the molecular mechanics calculations with the extended unit cells to study the possible surface reconstruction upon relaxation and hydroxylation of cubic perovskites.

  4. The water adsorption on the surfaces of SrMO3 (M= Ti, Zr, and Hf) crystalline oxides: quantum and classical modelling

    International Nuclear Information System (INIS)

    Evarestov, R A; Bandura, A V; Blokhin, E N

    2007-01-01

    Hybrid HF-DFT LCAO simulations of (001) surface properties and water adsorption on cubic SrTiO 3 , SrZrO 3 , and SrHfO 3 perovskites are performed in a single-slab model framework. The optimized atomic structures and water adsorption energies have been calculated for a single water molecule per the surface unit cell. The possibility of the water molecular dissociation was investigated. Basing on the experimental data and results of the ab initio calculations the new interatomic potentials have been developed to describe the bulk and surface properties of the binary and ternary titanium and zirconium oxides. The proposed force-field takes into account the polarization effects via the shell model. The force-field suggested was used in the molecular mechanics calculations with the extended unit cells to study the possible surface reconstruction upon relaxation and hydroxylation of cubic perovskites

  5. Nonlinear acoustic effects in the propagation of surface acoustic waves in SrTiO3 near the structural phase transition

    International Nuclear Information System (INIS)

    Balashova, E.V.; Lemanov, V.V.; Sherman, A.B.

    1986-01-01

    Generation process of a surface acoustic wave with summarized frequency in collinear propagation of two surface acoustic waves in SrTiO 3 crystal near crystal-phase transition O n → D 4h (T c ≅ 105 K) is investigated. Anomalous increase of a nonlinear parameter Γ ∼ (T-T c ) -1 attributed to a fluctuation mechanism is observed. It is shown that the presence of a surface layer in SrTiO 3 having a higher, than in crystal volume, temperature of phase transition results in summarized frequency signal oscillation

  6. The surface structure of SrTiO{sub 3} at high temperatures under influence of oxygen

    Energy Technology Data Exchange (ETDEWEB)

    Hesselberth, M. B. S.; Molen, S. J. van der; Aarts, J. [Kamerlingh Onnes Laboratory, Leiden University, P.O. Box 9504, 2300 RA Leiden (Netherlands)

    2014-02-03

    We use low energy electron microscopy to investigate the structure of the SrTiO{sub 3} (001) surface at elevated temperatures and different oxygen pressures. Upon varying the temperature between 500 °C and 900 °C in oxygen pressures ranging from 10{sup −9} millibar to 10{sup −4} millibar, two surface transitions are found to be present. The lower temperature (1 × 1) → (2 × 1) transition that is known to occur in ultrahigh vacuum can be reversed by increasing the oxygen pressure. At higher temperatures, we observe a (2 × 1) → disordered (1 × 1) transition which is irreversible in the experimental parameter range. The observations are expected to have a strong bearing on the growth of interface structures.

  7. Surface Chemistry of La0.99Sr0.01NbO4-d and Its Implication for Proton Conduction.

    Science.gov (United States)

    Li, Cheng; Pramana, Stevin S; Ni, Na; Kilner, John; Skinner, Stephen J

    2017-09-06

    Acceptor-doped LaNbO 4 is a promising electrolyte material for proton-conducting fuel cell (PCFC) applications. As charge transfer processes govern device performance, the outermost surface of acceptor-doped LaNbO 4 will play an important role in determining the overall cell performance. However, the surface composition is poorly characterized, and the understanding of its impact on the proton exchange process is rudimentary. In this work, the surface chemistry of 1 atom % Sr-doped LaNbO 4 (La 0.99 Sr 0.01 NbO 4-d , denoted as LSNO) proton conductor is characterized using LEIS and SIMS. The implication of a surface layer on proton transport is studied using the isotopic exchange technique. It has shown that a Sr-enriched but La-deficient surface layer of about 6-7 nm thick forms after annealing the sample under static air at 1000 °C for 10 h. The onset of segregation is found to be between 600 and 800 °C, and an equilibrium surface layer forms after 10 h annealing. A phase separation mechanism, due to the low solubility of Sr in LaNbO 4 , has been proposed to explain the observed segregation behavior. The surface layer was concluded to impede the water incorporation process, leading to a reduced isotopic fraction after the D 2 16 O wet exchange process, highlighting the impact of surface chemistry on the proton exchange process.

  8. Surface characterization, in vitro and in vivo biocompatibility of Mg-0.3Sr-0.3Ca for temporary cardiovascular implant.

    Science.gov (United States)

    Bornapour, M; Mahjoubi, H; Vali, H; Shum-Tim, D; Cerruti, M; Pekguleryuz, M

    2016-10-01

    Magnesium-based alloys are attractive candidate materials for medical applications. Our earlier work showed that the ternary Mg-0.3Sr-0.3Ca alloy exhibits slower degradation rates than both binary Mg-Sr and Mg-Ca alloys. The ternary alloy immersed in simulated body fluid (SBF) forms a compact surface layer of corrosion products that we hypothesized to be a Sr-substituted hydroxyapatite (HA). The main objectives of the current work are to understand the bio-degradation mechanism of Mg-0.3Sr-0.3Ca, to identify the exact nature of its protective layer and to evaluate the in vitro and in vivo biocompatibility of the alloy for cardiovascular applications. To better simulate the physiological environment, the alloy was immersed in SBF which was daily refreshed. Raman spectroscopy and X-Ray photoelectron spectroscopy (XPS) confirmed the formation of a thin, Sr-substituted HA layer at the interface between the alloy and the corrosion products. In vitro biocompatibility evaluated via indirect cytotoxicity assays using HUVECs showed no toxicity effect and ions extracted from Mg-0.3Sr-0.3Ca in fact increased the viability of HUVECs after one week. In vivo tests were performed by implanting a tubular Mg-0.3Sr-0.3Ca stent along with a WE43 control stent into the right and left femoral artery of a dog. Post implantation and histological analyses showed no thrombosis in the artery with Mg-0.3Sr-0.3Ca stent after 5weeks of implantation while the artery implanted with WE43 stent was extensively occluded and thrombosed. Microscopic observation of the Mg-0.3Sr-0.3Ca implant-tissue interface confirmed the in situ formation of Sr-substituted HA on the surface during in vivo test. These results show that the interfacial layer protects the surface of the Mg-0.3Sr-0.3Ca alloy both in vitro and in vivo, and is the key factor in the bio-corrosion resistance of the alloy. Copyright © 2016 Elsevier B.V. All rights reserved.

  9. Measurements and removal of substrate effects on the microwave surface impedance of YBCO films on SrTiO{sub 3}

    Energy Technology Data Exchange (ETDEWEB)

    Pompeo, N [Dipartimento di Fisica ' E Amaldi' and Unita CNISM, Universita Roma Tre, Via dellaVasca Navale 84, 00146 Rome (Italy); Muzzi, L [Dipartimento di Fisica ' E Amaldi' and Unita CNISM, Universita Roma Tre, Via dellaVasca Navale 84, 00146 Rome (Italy); Galluzzi, V [ENEA-Frascati, Via Enrico Fermi 45, 00044 Frascati, Rome (Italy); Marcon, R [Dipartimento di Fisica ' E Amaldi' and Unita CNISM, Universita Roma Tre, Via dellaVasca Navale 84, 00146 Rome (Italy); Silva, E [Dipartimento di Fisica ' E Amaldi' and Unita CNISM, Universita Roma Tre, Via dellaVasca Navale 84, 00146 Rome (Italy)

    2007-10-15

    We reconsider the problem of the measurements of the microwave complex surface impedance in thin superconducting films deposited on SrTiO{sub 3} substrates. We perform measurements of the complex surface impedance Z{sub s}' = R{sub s}'+i{delta}X{sub s}' of thin YBa{sub 2}Cu{sub 3}O{sub 7-{delta}} films deposited by laser ablation on SrTiO{sub 3} substrates. The typical oscillations due to the strong temperature variation of the SrTiO{sub 3} permittivity are confirmed in R{sub s}' and observed in {delta}X{sub s}'. The effects of the SrTiO{sub 3} substrate are evident even well below the superconducting transition temperature of YBa{sub 2}Cu{sub 3}O{sub 7-{delta}}. Similarly to previous works, we describe the overall response in terms of impedance transformations. We extend the known results by (i) considering the measurements of the imaginary part (ii) comparing the measurements to the absolute dc resistivity measured on the same sample, and (iii) suggesting a method for measuring the intrinsic thin film surface impedance by adjusting the substrate impedance. To demonstrate the feasibility of microwave measurements of intrinsic properties of films grown onto SrTiO{sub 3} substrates, we check the proposed method by measuring the field dependent surface impedance before and after removal of the substrate resonance.

  10. The Role of Controlled Surface Topography and Chemistry on Mouse Embryonic Stem Cell Attachment, Growth and Self-Renewal.

    Science.gov (United States)

    Macgregor, Melanie; Williams, Rachel; Downes, Joni; Bachhuka, Akash; Vasilev, Krasimir

    2017-09-14

    The success of stem cell therapies relies heavily on our ability to control their fate in vitro during expansion to ensure an appropriate supply. The biophysical properties of the cell culture environment have been recognised as a potent stimuli influencing cellular behaviour. In this work we used advanced plasma-based techniques to generate model culture substrates with controlled nanotopographical features of 16 nm, 38 nm and 68 nm in magnitude, and three differently tailored surface chemical functionalities. The effect of these two surface properties on the adhesion, spreading, and self-renewal of mouse embryonic stem cells (mESCs) were assessed. The results demonstrated that physical and chemical cues influenced the behaviour of these stem cells in in vitro culture in different ways. The size of the nanotopographical features impacted on the cell adhesion, spreading and proliferation, while the chemistry influenced the cell self-renewal and differentiation.

  11. CFD simulation of direct contact condensation with ANSYS CFX using surface renewal theory based heat transfer coefficients

    Energy Technology Data Exchange (ETDEWEB)

    Wanninger, Andreas; Ceuca, Sabin Cristian; Macian-Juan, Rafael [Technische Univ. Muenchen, Garching (Germany). Dept. of Nuclear Engineering

    2013-07-01

    Different approaches for the calculation of Direct Contact Condensation (DCC) using Heat Transfer Coefficients (HTC) based on the Surface Renewal Theory (SRT) are tested using the CFD simulation tool ANSYS CFX. The present work constitutes a preliminary study of the flow patterns and conditions observed using different HTC models. A complex 3D flow pattern will be observed in the CFD simulations as well as a strong coupling between the condensation rate and the two-phase flow dynamics. (orig.)

  12. Surface renewal: an advanced micrometeorological method for measuring and processing field-scale energy flux density data.

    Science.gov (United States)

    McElrone, Andrew J; Shapland, Thomas M; Calderon, Arturo; Fitzmaurice, Li; Paw U, Kyaw Tha; Snyder, Richard L

    2013-12-12

    Advanced micrometeorological methods have become increasingly important in soil, crop, and environmental sciences. For many scientists without formal training in atmospheric science, these techniques are relatively inaccessible. Surface renewal and other flux measurement methods require an understanding of boundary layer meteorology and extensive training in instrumentation and multiple data management programs. To improve accessibility of these techniques, we describe the underlying theory of surface renewal measurements, demonstrate how to set up a field station for surface renewal with eddy covariance calibration, and utilize our open-source turnkey data logger program to perform flux data acquisition and processing. The new turnkey program returns to the user a simple data table with the corrected fluxes and quality control parameters, and eliminates the need for researchers to shuttle between multiple processing programs to obtain the final flux data. An example of data generated from these measurements demonstrates how crop water use is measured with this technique. The output information is useful to growers for making irrigation decisions in a variety of agricultural ecosystems. These stations are currently deployed in numerous field experiments by researchers in our group and the California Department of Water Resources in the following crops: rice, wine and raisin grape vineyards, alfalfa, almond, walnut, peach, lemon, avocado, and corn.

  13. Modular PbSrS/PbS mid-infrared vertical external cavity surface emitting laser on Si

    Science.gov (United States)

    Khiar, A.; Rahim, M.; Fill, M.; Felder, F.; Zogg, H.; Cao, D.; Kobayashi, S.; Yokoyama, T.; Ishida, A.

    2011-07-01

    A mid-infrared vertical external cavity surface emitting laser (VECSEL) based on undoped PbS is described herein. A 200 nm-thick PbS active layer embedded between PbSrS cladding layers forms a double heterostructure. The layers are grown on a lattice and thermal expansion mismatched Si-substrate. The substrate is placed onto a flat bottom Bragg mirror again grown on a Si substrate, and the VECSEL is completed with a curved top mirror. Pumping is done optically with a 1.55 μm laser diode. This leads to an extremely simple modular fabrication process. Lasing wavelengths range from 3-3.8 μm at 100-260 K heat sink temperature. The lowest threshold power is ˜210 mWp and highest output power is ˜250 mWp. The influence of the different recombination mechanism as well as free carrier absorption on the threshold power is modeled.

  14. Surface morphology analysis of nanostructured (Ba sub x , Sr sub 1 sub - sub x)TiO sub 3 thin films using fractal method

    CERN Document Server

    Hong, K J; Choi, W K; Cho, J C

    2003-01-01

    Based on the fractal theory, this paper uses scanning electron microscopy images to investigate the roughness characteristics of nanostructured (Ba Sr)TiO sub 3 thin films by sol-gel methods. The percentage grain area, surface fractal dimensions and 3D image are evaluated using image analysis methods. The thickness of the (Ba Sr)TiO sub 3 thin films was 260-280 nm. The surface fractal dimensions were increased with strontium doping, and grain area, were decreased with it. The fractal dimension and the grain areas of the (Ba sub 0 sub . sub 7 Sr sub 0 sub . sub 3)TiO sub 3 thin films were 1.81 and 81%. Based on the image analysis, the roughness height of 3D images as 256 levels was about 3 nm and its distribution was about 35-40% for the (Ba sub 0 sub . sub 8 Sr sub 0 sub . sub 2)TiO sub 3 and (Ba sub 0 sub . sub 7 Sr sub 0 sub . sub 3)TiO sub 3 thin films. The roughness height of the BST thin films was distributed from 35% to 40% ranging from 3 nm to 4 nm. By increasing the strontium doping, the roughness hei...

  15. Nanosecond laser ablated copper superhydrophobic surface with tunable ultrahigh adhesion and its renewability with low temperature annealing

    Science.gov (United States)

    He, An; Liu, Wenwen; Xue, Wei; Yang, Huan; Cao, Yu

    2018-03-01

    Recently, metallic superhydrophobic surfaces with ultrahigh adhesion have got plentiful attention on account of their significance in scientific researches and industrial applications like droplet transport, drug delivery and novel microfluidic devices. However, the long lead time and transience hindered its in-depth development and industrial application. In this work, nanosecond laser ablation was carried out to construct grid of micro-grooves on copper surface, whereafter, by applying fast ethanol assisted low-temperature annealing, we obtained surface with superhydrophobicity and ultrahigh adhesion within hours. And the ultrahigh adhesion force was found tunable by varying the groove spacing. Using ultrasonic cleaning as the simulation of natural wear and tear in service, the renewability of superhydrophobicity was also investigated, and the result shows that the contact angle can rehabilitate promptly by the processing of ethanol assisted low-temperature annealing, which gives a promising fast and cheap circuitous strategy to realize the long wish durable metallic superhydrophobic surfaces in practical applications.

  16. Microwave absorption properties of polypyrrole-SrFe12O19-TiO2-epoxy resin nanocomposites: Optimization using response surface methodology

    Science.gov (United States)

    Seyed Dorraji, M. S.; Rasoulifard, M. H.; Amani-Ghadim, A. R.; Khodabandeloo, M. H.; Felekari, M.; Khoshrou, M. R.; hajimiri, I.

    2016-10-01

    At a few works are discussed about formation of heterogeneous composites with different distribution of particle shape and size that are used for electromagnetic absorption purposes. In this study a novel heterogeneous nanocpmposites is investigated. The nanocomposite has been successfully prepared based on epoxy resin including various nano-metal oxides (TiO2, SrFe12O19) and polypyrrole (PPy) by sol-gel and the solution chemistry method, respectively. The performance of prepared nanocomposite in absorption of microwave in X-band range was investigated and transmission line method by X-band waveguide straight was used to measure EM parameters of nanocomposites. The Response surface methodology (RSM) with central composite design (CCD) was utilized to study the effects of the wt.% TiO2 in SrFe12O19, wt.% Tio2-SrFe12O19 in PPy and wt.% TiO2-SrFe12O19-PPy in epoxy resin, on the microwave absorption properties with the absorber thickness of only 2 mm. The proposed quadratic model was in accordance with the experimental results with correlation coefficient of 96.5%. The optimum condition for maximum microwave absorption efficiency were wt.% TiO2 in SrFe12O19 of 70, wt.% TiO2-SrFe12O19 in PPy of 10 and wt.% TiO2-SrFe12O19-PPy in epoxy of 25. The sample prepared in optimal conditions indicated reflection loss of -15 dB corresponding to 97% absorption, at the range of 9.2-10.8 GHz.

  17. The dynamics of ultraviolet-induced oxygen vacancy at the surface of insulating SrTiO{sub 3}(0 0 1)

    Energy Technology Data Exchange (ETDEWEB)

    Suwanwong, S. [School of Physics, Suranaree University of Technology, Nakhon Ratchasima 30000 (Thailand); Program in General Science Teaching, Faculty of Education, Vongchavalitkul University, Nakhon Ratchasima 30000 (Thailand); Eknapakul, T. [School of Physics, Suranaree University of Technology, Nakhon Ratchasima 30000 (Thailand); Rattanachai, Y. [Department of Applied Physics, Faculty of Sciences and Liberal Arts, Rajamangala University of Technology Isan, Nakhon Ratchasima 30000 (Thailand); Masingboon, C. [School of Physics, Suranaree University of Technology, Nakhon Ratchasima 30000 (Thailand); Faculty of Science and Engineering, Kasetsart University, Chalermphrakiat Sakon Nakhon Province Campus, Sakon Nakhon 47000 (Thailand); Rattanasuporn, S.; Phatthanakun, R.; Nakajima, H. [Synchrotron Light Research Institute, Nakhon Ratchasima 30000 (Thailand); King, P.D.C. [SUPA, School of Physics and Astronomy, University of St. Andrews, St. Andrews, Fife KY16 9SS (United Kingdom); Hodak, S.K. [Department of Physics, Faculty of Science, Chulalongkorn University, Bangkok 10330 (Thailand); Meevasana, W., E-mail: worawat@g.sut.ac.th [School of Physics, Suranaree University of Technology, Nakhon Ratchasima 30000 (Thailand); NANOTEC-SUT Center of Excellence on Advanced Functional Nanomaterials, Suranaree University of Technology, Nakhon Ratchasima 30000 (Thailand); Thailand Center of Excellence in Physics, CHE, Bangkok 10400 (Thailand)

    2015-11-15

    Highlights: • The dynamics of UV-induced oxygen vacancy is studied from the change of surface resistance. • The formation of 2DEG at the insulating surface of SrTiO{sub 3} is confirmed by ARPES. • The UV-induced change in resistance responds differently to oxygen/gas exposure. • The behavior of resistance recovery suggests an alternative method of low-pressure sensing. - Abstract: The effect of ultra-violet (UV) irradiation on the electronic structure and the surface resistance of an insulating SrTiO{sub 3}(0 0 1) crystal is studied in this work. Upon UV irradiation, we show that the two-dimensional electron gas (2DEG) emerges at the insulating SrTiO{sub 3} surface and there is a pronounced change in the surface resistance. By combining the observations of the change in valance band and the resistance change under different environments of gas pressure and gas species, we find that UV-induced oxygen vacancies at the surface plays a major role in the resistance change. The dynamic of the resistance change at different oxygen pressures also suggests an alternative method of low-pressure sensing.

  18. The dynamics of ultraviolet-induced oxygen vacancy at the surface of insulating SrTiO_3(0 0 1)

    International Nuclear Information System (INIS)

    Suwanwong, S.; Eknapakul, T.; Rattanachai, Y.; Masingboon, C.; Rattanasuporn, S.; Phatthanakun, R.; Nakajima, H.; King, P.D.C.; Hodak, S.K.; Meevasana, W.

    2015-01-01

    Highlights: • The dynamics of UV-induced oxygen vacancy is studied from the change of surface resistance. • The formation of 2DEG at the insulating surface of SrTiO_3 is confirmed by ARPES. • The UV-induced change in resistance responds differently to oxygen/gas exposure. • The behavior of resistance recovery suggests an alternative method of low-pressure sensing. - Abstract: The effect of ultra-violet (UV) irradiation on the electronic structure and the surface resistance of an insulating SrTiO_3(0 0 1) crystal is studied in this work. Upon UV irradiation, we show that the two-dimensional electron gas (2DEG) emerges at the insulating SrTiO_3 surface and there is a pronounced change in the surface resistance. By combining the observations of the change in valance band and the resistance change under different environments of gas pressure and gas species, we find that UV-induced oxygen vacancies at the surface plays a major role in the resistance change. The dynamic of the resistance change at different oxygen pressures also suggests an alternative method of low-pressure sensing.

  19. Modification of Ag nanoparticles on the surface of SrTiO3 particles and resultant influence on photoreduction of CO2

    Science.gov (United States)

    Shao, Kunjuan; Wang, Yanjie; Iqbal, Muzaffar; Lin, Lin; Wang, Kai; Zhang, Xuehua; He, Meng; He, Tao

    2018-03-01

    Modification of a wide-bandgap semiconductor with noble metals that can exhibit surface plasmon effect is an effective approach to make it responsive to the visible light. In this work, a series of cubic and all-edge-truncated SrTiO3 with and without thermal pretreatment in air are modified by Ag nanoparticles via photodeposition method. The crystal structure, morphology, loading amount of Ag nanoparticles, and optical properties of the obtained Ag-SrTiO3 nanomaterials are well characterized by powder X-ray diffraction, scanning microscope, transmission electron microscope, energy disperse X-ray spectroscopy, ICP-MS and UV-vis diffuse-reflection spectroscopy. The loading amount and size of the Ag nanoparticles can be controlled to some extent by tuning the photodeposition time via growth-dissolution mechanism. The Ag nanoparticles are inclined to deposit on different locations on the surface of cubic and truncated SrTiO3 with and without thermal pretreatment. The resultant SrTiO3 modified by Ag nanoparticles exhibits visible light activity for photocatalytic reduction of CO2, which is closely related to the oxygen vacancy induced by thermal pretreatment, size and amount of Ag nanoparticles. Accordingly, there is an optimized photodeposition time for the synthesis of the photocatalyst that exhibits the highest photocatalytic activity.

  20. Surface and bulk modifications of 1.5 mole % Sr/La{sub 2}O{sub 3} catalyst with different Co, Ni, and Cu amounts

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez Cortes, Sergio; Fontal, Bernardo [Universidad de los Andes, Merida (Venezuela); Moronta, Delfin [Universidad Central de Venezuela, Caracas (Venezuela)

    2001-08-01

    The effects of Co, Ni and Cu oxide content on the surface and bulk of the 1.5 mole % Sr/La{sub 2}O{sub 3} catalysts were studied. Series of M/Sr-La catalysts (MCo, Ni, Cu) were prepared by successive immersion impregnation. The solids were characterized by X-ray diffraction (XRD), infrared spectroscopy (FTIR), temperature-programmed reduction (TPR), electron paramagnetic resonance (EPR), specific surface area measurements (BET) and thermogravimetric analysis (TGA). The Sr/La{sub 2}O{sub 3} modified with different Co, Ni, and Cu loading shows a strong metal oxide interaction with La{sub 2}O{sub 3}. This probably begin over anionic vacancies or structure defects favoring LaSrMO{sub x} solid solution formation with island-like structures according to a Volmer-Weber growth. It is proposed that the growth mode of La-Co, La-Ni and La-Cu stoichiometric phases occur from solid solutions. The formation of only a La-M single phase, probably non-stoichiometric, increases the material porosity while different phases favor the agglomeration or sintering of the particles. [Spanish] En este trabajo se estudia el efecto de la cantidad de cobalto, niquel y cobre sobre las estructuras superficial y masica del sistema 1.5% molar Sr/La{sub 2}O{sub 3}. Los catalizadores M/Sr-La (M = Co, Ni, Cu) fueron preparados por el metodo de impregnacion con exceso de solucion. Los solidos se caracterizaron por difraccion de rayos-X, espectroscopia infrarroja con transformada de Fourier, reduccion a temperatura programada, resonancia paramagnetica del electron, medidas del area superficial especifica por el metodo de BET y analisis termogravimetrico. El catalizador Sr/La{sub 2}O{sub 3} modificado con diferentes cantidades de Co, Ni y Cu muestra una interaccion fuerte con el oxido del metal de transicion, probablemente sobre las vacancias anionicas o defectos estructurales que favorecen la formacion de la solucion solida LaSrMox en forma de isla, segun el mecanismo de crecimiento de fase de Volmer

  1. Probing chiral superconductivity in Sr_2RuO_4 underneath the surface by point contact measurements

    International Nuclear Information System (INIS)

    Wang, He; Luo, Jiawei; Lou, Weijian

    2017-01-01

    Sr2RuO4 (SRO) is the prime candidate for a chiral p-wave superconductor with critical temperature T_c(SRO)∼1.5 K. Chiral domains with opposite chiralities p_x±ip_y have been proposed, but are yet to be confirmed. We measure the field dependence of the point contact (PC) resistance between a tungsten tip and an SRO–Ru eutectic crystal, where micrometer-sized Ru inclusions are embedded in SRO with an atomically sharp interface. Ruthenium is an s-wave superconductor with T_c(Ru)∼0.5 K; flux pinned near the Ru inclusions can suppress its superconductivity, as reflected in the PC resistance and spectra. This flux pinning effect originates from SRO underneath the surface and is very strong once flux is introduced. To fully remove flux pinning, one needs to thermally cycle the sample above T_c(SRO) or apply alternating fields with decreasing amplitude. With alternating fields, the observed hysteresis in magnetoresistance can be explained by domain dynamics, providing support for the existence of chiral domains. The origin of the strong pinning could be the chiral domains themselves.

  2. Solid-gate control of insulator to 2D metal transition at SrTiO3 surface

    Science.gov (United States)

    Schulman, Alejandro; Stoliar, Pablo; Kitoh, Ai; Rozenberg, Marcelo; Inoue, Isao H.

    As miniaturization of the semiconductor transistor approaches its limit, semiconductor industries are facing a major challenge to extend information processing beyond what can be attainable by conventional Si-based transistors. Innovative combinations of new materials and new processing platforms are desired. Recent discovery of the 2D electron gas (2DEG) at the surface of SrTiO3 (STO) and its electrostatic control, have carried it to the top of promising materials to be utilized in innovative devices. We report an electrostatic control of the carrier density of the 2DEG formed at the channel of bilayer-gated STO field-effect devices. By applying a gate electric field at room temperature, its highly insulating channel exhibits a transition to metallic one. This transition is accompanied by non-monotonic voltage-gain transfer characteristic with both negative and positive slope regions and unexpected enhancement of the sheet carrier density. We will introduce a numerical model to rationalize the observed features in terms of the established physics of field-effect transistors and the physics of percolation. Furthermore, we have found a clear signature of a Kondo effect that arises due to the interaction between the dilute 2DEG and localized Ti 3d orbitals originated by oxygen vacancies near the channel. On leave from CIC nanoGUNE, Spain.

  3. Intrareef variations in Li/Mg and Sr/Ca sea surface temperature proxies in the Caribbean reef-building coral Siderastrea siderea

    Science.gov (United States)

    Fowell, Sara E.; Sandford, Kate; Stewart, Joseph A.; Castillo, Karl D.; Ries, Justin B.; Foster, Gavin L.

    2016-10-01

    Caribbean sea surface temperatures (SSTs) have increased at a rate of 0.2°C per decade since 1971, a rate double that of the mean global change. Recent investigations of the coral Siderastrea siderea on the Belize Mesoamerican Barrier Reef System (MBRS) have demonstrated that warming over the last 30 years has had a detrimental impact on calcification. Instrumental temperature records in this region are sparse, making it necessary to reconstruct longer SST records indirectly through geochemical temperature proxies. Here we investigate the skeletal Sr/Ca and Li/Mg ratios of S. siderea from two distinct reef zones (forereef and backreef) of the MBRS. Our field calibrations of S. siderea show that Li/Mg and Sr/Ca ratios are well correlated with temperature, although both ratios are 3 times more sensitive to temperature change in the forereef than in the backreef. These differences suggest that a secondary parameter also influences these SST proxies, highlighting the importance for site- and species-specific SST calibrations. Application of these paleothermometers to downcore samples reveals highly uncertain reconstructed temperatures in backreef coral, but well-matched reconstructed temperatures in forereef coral, both between Sr/Ca-SSTs and Li/Mg-SSTs, and in comparison to the Hadley Centre Sea Ice and Sea Surface Temperature record. Reconstructions generated from a combined Sr/Ca and Li/Mg multiproxy calibration improve the precision of these SST reconstructions. This result confirms that there are circumstances in which both Li/Mg and Sr/Ca are reliable as stand-alone and combined proxies of sea surface temperature. However, the results also highlight that high-precision, site-specific calibrations remain critical for reconstructing accurate SSTs from coral-based elemental proxies.

  4. Ultrahigh vacuum STM/STS studies of the Bi-O surface in Bi2Sr2CuOy single crystals

    International Nuclear Information System (INIS)

    Ikeda, Kazuto; Tomeno, Izumi; Takamuku, Kenshi; Yamaguchi, Koji; Itti, Rittaporn; Koshizuka, Naoki

    1992-01-01

    Scanning tunneling microscopic and spectroscopic studies were made on cleaved surfaces of Bi 2 Sr 2 CuO y single crystals using an ultrahigh-vacuum scanning tunneling microscope (UHV-STM). The modulation structures of the Bi-O surface were observed at room temperature with atomic resolution. The tunneling spectra showed electronic gap structures similar to those observed for the Bi-O surface of superconducting Bi-2212 single crystals. This suggests that superconductivity is not directly related to the electronic structure observed in the Bi-O plane. (orig.)

  5. Oxygen tracer diffusion and surface exchange kinetics in Ba0.5Sr0.5Co0.8Fe0.2O3-δ

    NARCIS (Netherlands)

    Berenov, A.; Atkinson, A.; Kilner, J.; Ananyev, M.; Eremin, V.; Porotnikova, N.; Farlenkov, A.; Kurumchin, E.; Bouwmeester, Henricus J.M.; Bucher, E.; Sitte, W.

    2014-01-01

    The oxygen tracer diffusion coefficient, Db⁎, and the oxygen tracer surface exchange coefficient, k, were measured in Ba0.5Sr0.5Co0.8Fe0.2O3 − δ (BSCF5582) over the temperature range of 310–800 °C and the oxygen partial pressure range of 1.3 × 10−3–0.21 bar. Several measurement techniques were used:

  6. The Fermi surface and band folding in La{sub 2-x}Sr{sub x}CuO{sub 4}, probed by angle-resolved photoemission

    Energy Technology Data Exchange (ETDEWEB)

    Razzoli, E; Radovic, M; Patthey, L; Shi, M [Swiss Light Source, Paul Scherrer Institut, CH-5232 Villigen PSI (Switzerland); Sassa, Y; Chang, J [Laboratory for Neutron Scattering, Paul Scherrer Institut, CH-5232 Villigen PSI (Switzerland); Drachuck, G; Keren, A; Shay, M [Department of Physics, Technion-Israel Institute of Technology, Haifa 32000 (Israel); Maansson, M; Mesot, J [Laboratory for Synchrotron and Neutron Spectroscopy, EPF Lausanne, CH-1015 Lausanne (Switzerland); Berntsen, M H; Tjernberg, O [Materials Physics, KTH Royal Institute of Technology, S-16440 Kista (Sweden); Pailhes, S [CEA, CNRS, CE Saclay, Laboratoire Leon Brillouin, F-91191 Gif Sur Yvette (France); Momono, N [Department of Applied Sciences, Muroran Institute of Technology, Muroran 050-8585 (Japan); Oda, M; Ido, M [Department of Physics, Hokkaido University, Sapporo 060-0810 (Japan); Lipscombe, O J; Hayden, S M, E-mail: ming.shi@psi.c [H H Wills Physics Laboratory, University of Bristol, Tyndall Avenue, Bristol BS8 1TL (United Kingdom)

    2010-12-15

    A systematic angle-resolved photoemission study of the electronic structure of La{sub 2-x}Sr{sub x}CuO{sub 4} in a wide doping range is presented in this paper. In addition to the main energy band, we observed a weaker additional band, the ({pi}, {pi}) folded band, which shows unusual doping dependence. The appearance of the folded band suggests that a Fermi surface reconstruction is doping dependent and could already occur at zero magnetic field.

  7. A Modern Sr/Ca-δ18O-Sea Surface Temperature Calibration for Isopora Corals in the Great Barrier Reef

    Science.gov (United States)

    Brenner, L. D.; Linsley, B. K.; Potts, D. C.

    2014-12-01

    Most coral-based paleoceanographic studies have used massive colonies of Porites or Faviidae, due to their long, continuously accreted skeletal records and sub-annual resolution, but other sub-massive corals provide an untapped resource. The genus Isopora is a dominant reef builder in some high-energy environments in the tropical western Pacific, and was a major component of cores recovered on IODP Leg 325 off the Great Barrier Reef (GBR). Despite its abundance, Isopora remains largely unexplored and hence underutilized in paleoceanographic studies. We present a modern Sr/Ca-δ18O-Sea Surface Temperature (SST) calibration of modern Isopora corals (n=3) collected from inner and outer reef locations ranging from 1-13m depth by Heron Island in the southern GBR in 2012. Pairing the Isopora Sr/Ca record with monthly SST yielded an average relationship of SST=-11.48×(Sr/Ca)+131.1 (r2 = 0.42-0.78). The Sr/Ca sensitivity of -0.087 mmol/mol/°C is similar to the sensitivity for Porites that was corrected for tissue layer smoothing effects determined by Gagan et al. (2012). The similarity between our Sr/Ca-SST sensitivity and the corrected sensitivity for Porites suggests tissue layer effects are minimal in Isopora. The mean annual SST amplitude recorded by the corals from 2008-2011 (full annual cycles) was 5.3°C and the average δ18O annual cycle of 1.1‰ approximates that expected if salinity had little effect on coral δ18O, assuming a previously established conversion of -0.23‰ (δ18O)/°C for biogenic aragonite. The average annual salinity amplitude of 0.3 in gridded data from around Heron Island supports our conclusion that δ18O variability is forced almost completely by SST. This modern Sr/Ca-SST calibration will expand the paleoceanographic utility of Isopora and, by assisting interpretation of Sr/Ca data from fossil corals collected during IODP 325, will better constrain the timing and magnitude of sea level changes and surface conditions since the Last

  8. Surface and spectral studies of green emitting Sr{sub 3}B{sub 2}O{sub 6}:Tb{sup 3+} phosphor

    Energy Technology Data Exchange (ETDEWEB)

    Neharika [School of Physics, Shri Mata Vaishno Devi University, Katra 182320, J& K (India); Kumar, Vinay, E-mail: vinaykumar@smvdu.ac.in [School of Physics, Shri Mata Vaishno Devi University, Katra 182320, J& K (India); Sharma, J.; Singh, Vivek K. [School of Physics, Shri Mata Vaishno Devi University, Katra 182320, J& K (India); Ntwaeaborwa, O.M.; Swart, H.C. [Department of Physics, University of the Free State, PO Box 339, Bloemfontein ZA9300 (South Africa)

    2016-01-15

    Highlights: • XPS technique has been used to study the surface composition of the phosphor. • The phosphor is synthesized by combustion method using urea as fuel. • Multipole–multipole interaction was found to play a key role for concentration quenching of Tb{sup 3+} doped Sr{sub 3}B{sub 2}O{sub 6} phosphor. - Abstract: In this paper, we report the synthesis of trivalent Tb{sup 3+} doped Sr{sub 3}B{sub 2}O{sub 6} phosphor by combustion method using urea as an organic fuel. The structure of the product has been verified by X-ray diffraction study which shows a rhombohedral phase with a space group of R-3c having lattice constants a = 9.064 Å, b = 9.064 Å, c = 12.611 Å. X-ray photoelectron spectroscopy has been used to study the elemental composition and electronic states of the Tb{sup 3+} doped Sr{sub 3}B{sub 2}O{sub 6} phosphor. Photoluminescence spectra showed that the phosphor emits in the greenish region (with the main peak at 544 nm) of color gamut under UV excitation. The diffuse reflectance spectra of the Sr{sub 3}B{sub 2}O{sub 6} phosphor were studied. Lifetime and band gap of the phosphors were calculated to be 2.55 ms and 5.25 ± 0.02 eV, respectively.

  9. Improving the surface structure of high quality Sr{sub 2}FeMoO{sub 6} thin films for multilayer structures

    Energy Technology Data Exchange (ETDEWEB)

    Angervo, I., E-mail: ijange@utu.fi [Wihuri Physical Laboratory, Department of Physics and Astronomy, FI-20014 University of Turku (Finland); University of Turku Graduate School (UTUGS), University of Turku, FI-20014 Turku (Finland); Saloaro, M. [Wihuri Physical Laboratory, Department of Physics and Astronomy, FI-20014 University of Turku (Finland); Tikkanen, J. [Wihuri Physical Laboratory, Department of Physics and Astronomy, FI-20014 University of Turku (Finland); University of Turku Graduate School (UTUGS), University of Turku, FI-20014 Turku (Finland); Huhtinen, H.; Paturi, P. [Wihuri Physical Laboratory, Department of Physics and Astronomy, FI-20014 University of Turku (Finland)

    2017-02-28

    Highlights: • The effects of PLD laser fluence and deposition temperature are investigated on SFMO thin films. • We focus on improving the surface structure of the SFMO thin films. • Both the surface structure and the Curie temperature can be improved by fabricating the films at 900 °C. - Abstract: Two sets of Sr{sub 2}FeMoO{sub 6} thin films were prepared with pulsed laser deposition and the effect of the laser fluence and the deposition temperature was investigated. The Sr{sub 2}FeMoO{sub 6} thin films showed clear evidence of impurity phases when the laser fluence was altered. Phase pure films resulted through the whole temperature range between 900 °C and 1050 °C when a proper laser fluence was used. Films fabricated at lower deposition temperatures resulted with smaller surface roughnesses around 5 nm, higher Curie temperatures and with relatively high saturation magnetization values. The Curie temperature was determined from the minimum of the first order derivative and results showed the highest values of 350 K and above. The films with the highest Curie temperature reached zero magnetization above 400 K. The results indicate that both high microstructural and high magnetic quality Sr{sub 2}FeMoO{sub 6} thin films can be obtained with a deposition temperature between 900 °C and 950 °C. This provides better fabrication parameters for the upcoming SFMO multilayer structures.

  10. Fermi surface investigation in the scanning tunneling microscopy of Bi2Sr2CaCu2O8

    International Nuclear Information System (INIS)

    Voo, K.K.; Wu, W.C.; Chen, H.Y.; Mou, C.Y.

    2004-01-01

    Within the ideal Fermi liquid picture, the impurity-induced spatial modulation of local density of states (LDOS) in the d-wave superconductor Bi 2 Sr 2 CaCu 2 O 8 is investigated at different superconducting (SC) gap sizes. These LDOS spectra are related to the finite-temperature dI/dV spectra in scanning tunneling microscopy (STM), when the Fermi distribution factor is deconvoluted away from dI/dV. We find stripe-like structures even in the zero gap case due to a local-nesting mechanism. This mechanism is different from the octet-scattering mechanism in the d-wave SC (dSC) state proposed by McElroy et al. [K. McElroy, R.W. Simmonds, J.E. Hoffman, D.H. Lee, J. Orenstein, H. Eisaki, S. Uchida, J.C. Davis, Nature 422 (2003) 592]. The zero gap LDOS is related to the normal state dI/dV. The zero gap spectra when Fourier-transformed into the reciprocal space, can reveal the information of the entire Fermi surface at a single measuring bias voltage, in contrast to the point-wise tracing out proposed by McElroy et al. This may serve as another way to check the reality of Landau quasiparticles in the normal state. We have also re-visited the octet-scattering mechanism in the dSC state and pointed out that, due to the Umklapp symmetry, there are additional peaks in the reciprocal space that experimentally yet to be found

  11. APPLICATION OF A SURFACE-RENEWAL MODEL TO PERMEATE-FLUX DATA FOR CONSTANTPRESSURE CROSS-FLOW MICROFILTRATION WITH DEAN VORTICES

    Directory of Open Access Journals (Sweden)

    G. Idan

    2015-06-01

    Full Text Available AbstractThe introduction of flow instabilities into a microfiltration process can dramatically change several elements such as the surface-renewal rate, permeate flux, specific cake resistance, and cake buildup on the membrane in a positive way. A recently developed surface-renewal model for constant-pressure, cross-flow microfiltration (Hasan et al., 2013 is applied to the permeate-flux data reported by Mallubhotla and Belfort (1997, one set of which included flow instabilities (Dean vortices while the other set did not. The surface-renewal model has two forms - the complete model and an approximate model. For the complete model, the introduction of vortices leads to a 53% increase in the surface-renewal rate, which increases the limiting (i.e., steady-state permeate flux by 30%, decreases the specific cake resistance by 14.5% and decreases the limiting cake mass by 15.5% compared to operation without vortices. For the approximate model, a 50% increase in the value of surface renewal rate is shown due to vortices, which increases the limiting permeate flux by 30%, decreases the specific cake resistance by 10.5% and decreases the limiting cake mass by 13.7%. The cake-filtration version of the critical-flux model of microfiltration (Field et al., 1995 is also compared against the experimental permeate-flux data of Mallubhotla and Belfort (1997. Although this model can represent the data, the quality of its fit is inferior compared to that of the surface-renewal model.

  12. First-principles investigations of electronic and magnetic properties of SrTiO3 (001) surfaces with adsorbed ethanol and acetone molecules

    Science.gov (United States)

    Adeagbo, Waheed A.; Fischer, Guntram; Hergert, Wolfram

    2011-05-01

    First-principles methods based on density functional theory are used to investigate the electronic and magnetic properties of molecular interaction of the TiO2 terminated SrTiO3 (100) surface with ethanol or acetone. Both the perfect surface and the surface with an oxygen or a titanium vacancy in the top layer are considered. Ethanol and acetone are preferentially adsorbed molecularly via their respective oxygen atom on top of the Ti atom on the perfect surface. In case of an oxygen vacancy the adsorption of ethanol or acetone occurs directly on top of the vacancy and does not significantly affect the magnetism caused by the vacancy. In the case of a titanium vacancy both adsorbates occupy positions above Ti atoms. During this adsorption process the ethanol molecule dissociates into a CH3CO radical and three hydrogen atoms. The latter form hydroxide bonds with three of the four dangling oxygen bonds around the Ti vacancy and any magnetic moment induced by the Ti vacancy is annihilated. Thus the ethanol and acetone have a different impact on the surface magnetism of the SrTiO3 (100) surface.

  13. Oxygen Electrode Kinetics and Surface Composition of Dense (La0.75Sr0.25)0.95MnO3 on YSZ

    DEFF Research Database (Denmark)

    Wu, Yuehua; Hansen, Karin Vels; Norrman, Kion

    2013-01-01

    in situ at temperatures from 660 to 860 C using a controlled atmosphere high temperature scanning probe microscope (CAHT-SPM) setup for measurements of impedance spectroscopy and potential sweep. The oxygen partial pressure, pO2, was varied. Further, ex situ surface analysis by time of flight secondary...... ion mass spectrometry (TOF-SIMS) and structure examination by scanning electron microscopy (SEM) were performed. Segregation of Sr and La oxides to LSM surfaces and Mn rich oxide to the three phase boundary (TPB) was observed. YSZ and LSM attract different oxides/impurities. The oxygen electrode...

  14. The new versatile general purpose surface-muon instrument (GPS) based on silicon photomultipliers for μSR measurements on a continuous-wave beam.

    Science.gov (United States)

    Amato, A; Luetkens, H; Sedlak, K; Stoykov, A; Scheuermann, R; Elender, M; Raselli, A; Graf, D

    2017-09-01

    We report on the design and commissioning of a new spectrometer for muon-spin relaxation/rotation studies installed at the Swiss Muon Source (SμS) of the Paul Scherrer Institute (PSI, Switzerland). This new instrument is essentially a new design and replaces the old general-purpose surface-muon (GPS) instrument that has been for long the workhorse of the μSR user facility at PSI. By making use of muon and positron detectors made of plastic scintillators read out by silicon photomultipliers, a time resolution of the complete instrument of about 160 ps (standard deviation) could be achieved. In addition, the absence of light guides, which are needed in traditionally built μSR instrument to deliver the scintillation light to photomultiplier tubes located outside magnetic fields applied, allowed us to design a compact instrument with a detector set covering an increased solid angle compared with the old GPS.

  15. Diffusion of I{sup -}, Cs{sup +}, and Sr{sup 2+} in compacted bentonite - Anion exclusion and surface diffusion

    Energy Technology Data Exchange (ETDEWEB)

    Eriksen, T.E.; Jansson, Mats [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Nuclear Chemistry

    1996-11-01

    The diffusion of I, Cs and Sr ions in bentonite compacted to a dry density of 1.8 gr/cm{sup 3} and saturated with two groundwaters of different ionic strength have been studied experimentally using the through diffusion technique. The I{sup -} diffusivity and diffusion porosity were found to be concentration independent in the concentration range exp(-8) to exp(-2) mol/dm{sup 3}. The diffusion porosity, being only a fraction of the water porosity for normal groundwaters, is strongly ionic strength dependent due to anion exclusion. The dependence of the diffusion of Cs{sup +} and Sr{sup 2+} on the sorption intensity is accommodated by a model encompassing diffusion of the sorbed cations within the electrical double layer next to the mineral surface in addition to diffusion in the pore water. 18 refs, 12 figs.

  16. Magnetic and electrical transport properties of LaBaCo2O(5.5+δ) thin films on vicinal (001) SrTiO3 surfaces.

    Science.gov (United States)

    Ma, Chunrui; Liu, Ming; Collins, Gregory; Wang, Haibin; Bao, Shanyong; Xu, Xing; Enriquez, Erik; Chen, Chonglin; Lin, Yuan; Whangbo, Myung-Hwan

    2013-01-23

    Highly epitaxial LaBaCo(2)O(5.5+δ) thin films were grown on the vicinal (001) SrTiO(3) substrates with miscut angles of 0.5°, 3.0°, and 5.0° to systemically study strain effect on its physical properties. The electronic transport properties and magnetic behaviors of these films are strongly dependent on the miscut angles. With increasing the miscut angle, the transport property of the film changes from semiconducting to semimetallic, which results most probably from the locally strained domains induced by the surface step terraces. In addition, a very large magnetoresistance (34% at 60 K) was achieved for the 0.5°-miscut film, which is ~30% larger than that for the film grown on the regular (001) SrTiO(3) substrates.

  17. The Fermi surface of Sr{sub 2}RuO{sub 4}: spin-orbit and anisotropic Coulomb interaction effects

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Guoren; Gorelov, Evgeny; Sarvestani, Esmaeel; Pavarini, Eva [Institute for Advanced Simulation, Forschungszentrum Juelich, D-52425 Juelich (Germany)

    2016-07-01

    The topology of the Fermi surface of Sr{sub 2}RuO{sub 4} is well described by local density approximation calculations with spin-orbit interaction, but the relative size of its different sheets is not. By accounting for many-body effects via dynamical mean-field theory, we show that the standard isotropic Coulomb interaction worsen or does not correct this discrepancy. In order to reproduce experiments, it is essential to include the Coulomb anisotropy. The latter is small but has strong effects; it competes with the Coulomb-enhanced spin-orbit coupling and with the isotropic Coulomb term. This mechanism is likely to be at work in other multi-orbital systems. Finally, we find a strong spin-orbital entanglement. This supports the view that the conventional description of Cooper pairs via factorized spin and orbital part might not apply to Sr{sub 2}RuO{sub 4}.

  18. Adsorption of UO{sub 2}{sup 2+} in surfaces of SrTiO{sub 3}; Adsorcion de UO{sub 2}{sup 2+} en superficies de SrTiO{sub 3}

    Energy Technology Data Exchange (ETDEWEB)

    Ortiz O, H.B.; Ordonez R, E.; Fernandez V, S.M. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)]. e-mail: huemantzin@prodigy.net.mx

    2005-07-01

    The internationally accepted solution in the administration of the high level radioactive residuals is the multi barrier deep geologic storage which should guarantee that do not exist flights neither transfer of residuals to the atmosphere in time periods of at least 10,000 years. In this confinement type exists the interest to study materials that can be used as engineering barriers as well as the diverse interaction phenomena between these and the radionuclides. In this work it is presented the physicochemical characterization and evaluation of the surface properties and of adsorption of U(VI) in form of UO{sub 2}(NO{sub 3}){sub 2} on the SrTiO{sub 3} like possible candidate for contention barrier in the deep geologic confinement. The made studies showed that the SrTiO{sub 3} is stable to temperatures between 0 and 800 C. At the same time it could settle down that the maximum sorption percentages are reached to near pH to the isoelectric point, where chemical species prevail in solution of the type UO{sub 2}(X){sup -}. (Author)

  19. Materials surface treatments by concentrated solar light: a renewable energy option

    International Nuclear Information System (INIS)

    Martinez, D.; Rodriguez, J.

    1998-01-01

    The possible applications of solar furnaces to materials surface treatment are explained in an illustrative manner. A brief description of these systems is exposed, as well as an overview of the feasible industrial or testing applications for which their validity has been proven. (Author) 5 refs

  20. Recent developments in automatic solid-phase extraction with renewable surfaces exploiting flow-based approaches

    DEFF Research Database (Denmark)

    Miró, Manuel; Hartwell, Supaporn Kradtap; Jakmunee, Jaroon

    2008-01-01

    ,on-line SPE assays performed in permanent mode lack sufficient reliability as a consequence of progressively tighter packing of the bead reactor, contamination of the solid surfaces and potential leakage of functional moieties. This article overviews the current state-of-the-art of an appealing tool...... chemical-derivatization reactions, and it pinpoints the most common instrumental detection techniques utilized. We present and discuss in detail relevant environmental and bioanalytical applications reported in the past few years....

  1. INFLUENCE OF RESIDENCE-TIME DISTRIBUTION ON A SURFACE-RENEWAL MODEL OF CONSTANT-PRESSURE CROSS-FLOW MICROFILTRATION

    Directory of Open Access Journals (Sweden)

    W. Zhang

    2015-03-01

    Full Text Available Abstract This work examines the influence of the residence-time distribution (RTD of surface elements on a model of cross-flow microfiltration that has been proposed recently (Hasan et al., 2013. Along with the RTD from the previous work (Case 1, two other RTD functions (Cases 2 and 3 are used to develop theoretical expressions for the permeate-flux decline and cake buildup in the filter as a function of process time. The three different RTDs correspond to three different startup conditions of the filtration process. The analytical expressions for the permeate flux, each of which contains three basic parameters (membrane resistance, specific cake resistance and rate of surface renewal, are fitted to experimental permeate flow rate data in the microfiltration of fermentation broths in laboratory- and pilot-scale units. All three expressions for the permeate flux fit the experimental data fairly well with average root-mean-square errors of 4.6% for Cases 1 and 2, and 4.2% for Case 3, respectively, which points towards the constructive nature of the model - a common feature of theoretical models used in science and engineering.

  2. Pair momentum distribution in Bi2Sr2CaCu2O8+δ measured by positron annihilation: Existence and nature of the Fermi surface

    International Nuclear Information System (INIS)

    Chan, L.P.; Harshman, D.R.; Lynn, K.G.; Massidda, S.; Mitzi, D.B.

    1991-01-01

    We report the first measurement of the positron-electron momentum density in superconducting single-crystal Bi 2 Sr 2 CaCu 2 O 8+δ (T c ∼90 K). The observed anisotropy exhibits a twofold (rather than fourfold) symmetry, which is attributed to the superlattice modulation along the b axis of the BiO 2 layers. Subtraction of the superlattice contribution also reveals a pair momentum distribution consistent with the CuO 2 and BiO 2 Fermi surfaces, and in reasonable agreement with the theoretical pair momentum density derived from band theory

  3. Pair momentum distribution in Bi2Sr2CaCu2O(8+delta) measured by positron annihilation - Existence and nature of the Fermi surface

    Science.gov (United States)

    Chan, L. P.; Lynn, K. G.; Harshman, D. R.; Massidda, S.; Mitzi, D. B.

    1991-09-01

    The first measurement is reported of the position-electron momentum density in superconducting single-crystal Bi2Sr2CaCu2O(8+delta)(Tc roughly 90 K). The observed anisotropy exhibits a twofold (rather than fourfold) symmetry, which is attributed to the superlattice modulation along the b axis of the BiO2 layers. Subtraction of the superlattice contribution also reveals a pair momentum distribution consistent with the CuO2 and BiO2 Fermi surfaces, and in reasonable agreement with the theoretical pair momentum density derived from band theory.

  4. The dynamics of Cs-137 and Sr-90 pollution of surface water systems of Belarus of Chernobyl origin

    Energy Technology Data Exchange (ETDEWEB)

    Datskevich, P.O.; Dolgov, V.M.; Golikov, Yu.N.; Zemskov, V.N.; Komissarov, F.D.; Khvaley, O.D.

    1995-12-31

    The Belarus water ecosystems have been the object of investigation concerning currents and reservoirs affected by the Chernobyl APS catastrophe. The radio monitoring of samples of water systems components was implemented with the use of modern methods of radiochemistry and ionizing radiations registration. The factual material of water ecosystems sites observation presented its analysis is done and the regularities, tendencies and anomalies are revealed in the Cs-137 and Sr-90 distribution, transport and accumulation for water components.

  5. Surface structure of Bi2Sr2CaCu2O(8+delta) high-temperature superconductors studied using low-energy electron diffraction

    Science.gov (United States)

    Lindberg, P. A. P.; Shen, Z.-X.; Wells, B. O.; Mitzi, D. B.; Lindau, I.

    1988-12-01

    The surface structure of Bi2Sr2CaCu2O(8+delta) has been studied using low-energy electron diffraction (LEED). Sharp diffraction spots indicative of a well-ordered surface are observed. The LEED patterns unequivocally show that this type of material preferentially cleaves along the a-b planes of the nearly tetragonal unit cell. A superstructure extending along one of the axes in the a-b plane (b) is found to have a periodicity of 27 + or - 0.5 A, in good agreement with earlier studies of the three-dimensional crystal structure. The superstructure at the surface is nonlocal in character and reflects the long-range superlattice of the bulk along the b axis. Intensity modulations of the diffraction spots oriented along the b axis are also reported and discussed in terms of the cell dimension of the unit cell along the b axis.

  6. Surface structure of Bi2Sr2CaCu2O/sub 8+//sub δ high-temperature superconductors studied using low-energy electron diffraction

    International Nuclear Information System (INIS)

    Lindberg, P.A.P.; Shen, Z.; Wells, B.O.; Mitzi, D.B.; Lindau, I.; Spicer, W.E.; Kapitulnik, A.

    1988-01-01

    The surface structure of Bi 2 Sr 2 CaCu 2 O/sub 8+//sub δ has been studied using low-energy electron diffraction (LEED). Sharp diffraction spots indicative of a well-ordered surface are observed. The LEED patterns unequivocally show that this type of material preferentially cleaves along the a-b planes of the nearly tetragonal unit cell. A superstructure extending along one of the axes in the a-b plane (b) is found to have a periodicity of 27 +- 0.5 A, in good agreement with earlier studies of the three-dimensional crystal structure. We conclude that the superstructure at the surface is nonlocal in character and reflects the long-range superlattice of the bulk along the b axis. Intensity modulations of the diffraction spots oriented along the b axis are also reported and discussed in terms of the cell dimension of the unit cell along the b axis

  7. Enhancing photocatalysis in SrTiO3 by using Ag nanoparticles: A two-step excitation model for surface plasmon-enhanced photocatalysis

    International Nuclear Information System (INIS)

    Ma, Lei; Sun, Tao; Cai, Hua; Zhou, Zhi-Quan; Sun, Jian; Lu, Ming

    2015-01-01

    Surface plasmon (SP)-enhanced ultraviolet and visible photocatalytic activities of SrTiO 3 (STO) are observed after incorporating Ag nanoparticles (Ag-NPs) on STO surfaces. A two-step excitation model is proposed to explain the SP-enhanced photocatalysis. The point of the model is that an electron at the valence band of STO is first excited onto the Fermi level of Ag-NP by the SP field generated on the Ag-NP, and then injected into the conduction band of STO from the SP band, leaving a hole at the valence band of STO. A full redox catalytic reaction at the surface of STO is then available. For Ag-NP incorporated STO, up-converted and inter-band photoluminescence emissions of STO are observed, and nonlinear evolutions of photocatalytic activity with illumination light powers are found. Furthermore, near infrared photocatalysis is detected. These results support the proposed model

  8. Appendix to Health and Safety Laboratory environmental quarterly, March 1, 1976--June 1, 1976. [Tabulated data on content of lead in surface air and /sup 7/Be, /sup 95/Zr, /sup 137/Cs, /sup 144/Ce, and /sup 90/Sr in surface air, milk, drinking water, and foods sampled in USA

    Energy Technology Data Exchange (ETDEWEB)

    Hardy, E.P. Jr.

    1976-07-01

    Tabulated data are presented on: the monthly deposition of /sup 89/Sr and /sup 90/Sr at some 100 world land sites; the content of lead and /sup 7/Be, /sup 95/Zr, /sup 137/Cs, and /sup 144/Ce in samples of surface air from various world sites; and the content of /sup 90/Sr in samples of milk, drinking water, and animal and human diets collected at various locations throughout the USA. (CH)

  9. Understanding the influence of surface chemical states on the dielectric tunability of sputtered Ba0.5Sr0.5TiO3 thin films

    Science.gov (United States)

    Venkata Saravanan, K.; Raju, K. C. James

    2014-03-01

    The surface chemical states of RF-magnetron sputtered Ba0.5Sr0.5TiO3 (BST5) thin films deposited at different oxygen mixing percentage (OMP) was examined by x-ray photoelectron spectroscopy. The O1s XPS spectra indicate the existence of three kinds of oxygen species (dissociated oxygen ion O2 -, adsorbed oxide ion O- and lattice oxide ion O2-) on the films’ surface, which strongly depends on OMP. The presence of oxygen species other than lattice oxygen ion makes the films’ surface highly reactivity to atmospheric gases, resulting in the formation of undesired surface layers. The XPS results confirm the formation of surface nitrates for the films deposited under oxygen deficient atmosphere (OMP ≦̸ 25%), whereas the films deposited in oxygen rich atmosphere (OMP ≧̸ 75%) show the presence of metal-hydroxide. The influence of a surface dead layer on the tunable dielectric properties of BST5 films have been studied in detail and are reported. Furthermore, our observations indicate that an optimum ratio of Ar:O2 is essential for achieving desired material and dielectric properties in BST5 thin films. The films deposited at 50% OMP have the highest dielectric tunability of ~65% (@280 kV cm-1), with good ɛ r-E curve symmetry of 98% and low tan δ of 0.018. The figure of merit for these films is about 35, which is promising for frequency agile device applications.

  10. Ab initio hybrid DFT calculations of BaTiO{sub 3}, PbTiO{sub 3}, SrZrO{sub 3} and PbZrO{sub 3} (111) surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Eglitis, Roberts I., E-mail: rieglitis@gmail.com

    2015-12-15

    Highlights: • Surface energies for AO{sub 3}-term (111) surfaces are larger than for Ti (Zr)-term surfaces. • A increase of Ti−O (Zr−O) bond covalency near the ABO{sub 3} (111) surface relative to the bulk is observed. • The ABO{sub 3} (111) surface energy is larger than the earlier calculated (001) surface energy. • Band gap for PbTiO{sub 3}, SrZrO{sub 3} and PbZrO{sub 3} (111) surfaces becomes smaller, but for BaTiO{sub 3} (111) larger with respect to the bulk . - Abstract: The results of ab initio calculations for polar BaTiO{sub 3}, PbTiO{sub 3}, SrZrO{sub 3} and PbZrO{sub 3} (111) surfaces using the CRYSTAL code are presented. By means of the hybrid B3LYP approach, the surface relaxation has been calculated for two possible B (B = Ti or Zr) or AO{sub 3} (A = Ba, Pb or Sr) BaTiO{sub 3}, PbTiO{sub 3}, SrZrO{sub 3} and PbZrO{sub 3} (111) surface terminations. According to performed B3LYP calculations, all atoms of the first surface layer, for both terminations, relax inwards. The only exception is a small outward relaxation of the PbO{sub 3}-terminated PbTiO{sub 3} (111) surface upper layer Pb atom. B3LYP calculated surface energies for BaO{sub 3}, PbO{sub 3}, SrO{sub 3} and PbO{sub 3}-terminated BaTiO{sub 3}, PbTiO{sub 3}, SrZrO{sub 3} and PbZrO{sub 3} (111) surfaces are considerably larger than the surface energies for Ti (Zr)-terminated (111) surfaces. Performed B3LYP calculations indicate a considerable increase of Ti−O (Zr−O) chemical bond covalency near the BaTiO{sub 3}, PbTiO{sub 3}, SrZrO{sub 3} and PbZrO{sub 3} (111) surface relative to the BaTiO{sub 3}, PbTiO{sub 3}, SrZrO{sub 3} and PbZrO{sub 3} bulk. Calculated band gaps at the Γ-point near the PbTiO{sub 3}, SrZrO{sub 3} and PbZrO{sub 3} (111) surfaces are reduced, but near BaTiO{sub 3} (111) surfaces increased, with respect to the BaTiO{sub 3}, PbTiO{sub 3}, SrZrO{sub 3} and PbZrO{sub 3} bulk band gap at the Γ-point values.

  11. Crystal structure and surface characteristics of Sr-doped GdBaCo2O6−δ double perovskites: oxygen evolution reaction and conductivity

    KAUST Repository

    Pramana, Stevin S.

    2017-12-04

    A cheap and direct solution towards engineering better catalysts through identification of novel materials is required for a sustainable energy system. Perovskite oxides have emerged as potential candidates to replace the less economically attractive Pt and IrO2 water splitting catalysts. In this work, excellent electrical conductivity (980 S cm−1) was found for the double perovskite of composition GdBa0.6Sr0.4Co2O6−δ which is consistent with a better oxygen evolution reaction activity with the onset polarisation of 1.51 V with respect to a reversible hydrogen electrode (RHE). GdBa1−xSrxCo2O6−δ with increasing Sr content was found to crystallise in the higher symmetry tetragonal P4/mmm space group in comparison with the undoped GdBaCo2O6−δ which is orthorhombic (Pmmm), and yields higher oxygen uptake, accompanied by higher Co oxidation states. This outstanding electrochemical performance is explained by the wider carrier bandwidth, which is a function of Co–O–Co buckling angles and Co–O bond lengths. Furthermore the higher oxygen evolution activity was observed despite the formation of non-lattice oxides (mainly hydroxide species) and enrichment of alkaline earth ions on the surface.

  12. Crystal structure and surface characteristics of Sr-doped GdBaCo2O6−δ double perovskites: oxygen evolution reaction and conductivity

    KAUST Repository

    Pramana, Stevin S.; Cavallaro, Andrea; Li, Cheng; Handoko, Albertus D.; Chan, Kuang Wen; Walker, Robert J.; Regoutz, Anna; Herrin, Jason S.; Yeo, Boon Siang; Payne, David J.; Kilner, John A.; Ryan, Mary P.; Skinner, Stephen J.

    2017-01-01

    A cheap and direct solution towards engineering better catalysts through identification of novel materials is required for a sustainable energy system. Perovskite oxides have emerged as potential candidates to replace the less economically attractive Pt and IrO2 water splitting catalysts. In this work, excellent electrical conductivity (980 S cm−1) was found for the double perovskite of composition GdBa0.6Sr0.4Co2O6−δ which is consistent with a better oxygen evolution reaction activity with the onset polarisation of 1.51 V with respect to a reversible hydrogen electrode (RHE). GdBa1−xSrxCo2O6−δ with increasing Sr content was found to crystallise in the higher symmetry tetragonal P4/mmm space group in comparison with the undoped GdBaCo2O6−δ which is orthorhombic (Pmmm), and yields higher oxygen uptake, accompanied by higher Co oxidation states. This outstanding electrochemical performance is explained by the wider carrier bandwidth, which is a function of Co–O–Co buckling angles and Co–O bond lengths. Furthermore the higher oxygen evolution activity was observed despite the formation of non-lattice oxides (mainly hydroxide species) and enrichment of alkaline earth ions on the surface.

  13. Sequestration of Sr-90 Subsurface Contamination in the Hanford 100-N Area by Surface Infiltration of a Ca-Citrate-Phosphate Solution

    Energy Technology Data Exchange (ETDEWEB)

    Szecsody, James E.; Rockhold, Mark L.; Oostrom, Martinus; Moore, R. C.; Burns, Carolyn A.; Williams, Mark D.; Zhong, Lirong; Fruchter, Jonathan S.; McKinley, James P.; Vermeul, Vincent R.; Covert, Matthew A.; Wietsma, Thomas W.; Breshears, Andrew T.; Garcia, Ben J.

    2009-03-01

    The objective of this project is to develop a method to emplace apatite precipitate in the 100N vadose zone, which results in sorption and ultimately incorporation of Sr-90 into the apatite structure. The Ca-citrate-PO4 solution can be infiltrated into unsaturated sediments to result in apatite precipitate to provide effective treatment of Sr-90 contamination. Microbial redistribution during solution infiltration and a high rate of citrate biodegradation for river water microbes (water used for solution infiltration) results in a relatively even spatial distribution of the citrate biodegradation rate and ultimately apatite precipitate in the sediment. Manipulation of the Ca-citrate-PO4 solution infiltration strategy can be used to result in apatite precipitate in the lower half of the vadose zone (where most of the Sr-90 is located) and within low-K layers (which are hypothesized to have higher Sr-90 concentrations). The most effective infiltration strategy to precipitate apatite at depth (and with sufficient lateral spread) was to infiltrate a high concentration solution (6 mM Ca, 15 mM citrate, 60 mM PO4) at a rapid rate (near ponded conditions), followed by rapid, then slow water infiltration. Repeated infiltration events, with sufficient time between events to allow water drainage in the sediment profile can be used to buildup the mass of apatite precipitate at greater depth. Low-K heterogeneities were effectively treated, as the higher residual water content maintained in these zones resulted in higher apatite precipitate concentration. High-K zones did not receive sufficient treatment by infiltration, although an alternative strategy of air/surfactant (foam) was demonstrated effective for targeting high-K zones. The flow rate manipulation used in this study to treat specific depths and heterogeneities are not as easy to implement at field scale due to the lack of characterization of heterogeneities and difficulty tracking the wetting front over a large

  14. A modern Sr/Ca-δ18O-sea surface temperature calibration for Isopora corals on the Great Barrier Reef

    Science.gov (United States)

    Brenner, Logan D.; Linsley, Braddock K.; Potts, Donald C.

    2017-02-01

    Isopora (Acroporidae) is a genus of often encrusting, branching to submassive corals that are common in many shallow habitats on modern and fossil Indo-West Pacific reefs. Although abundant, Isopora is largely absent from paleoceanographic literature. The scarcity of large Porites and the abundance of Isopora retrieved from the Great Barrier Reef (GBR) on Integrated Ocean Drilling Program Expedition 325 focused paleoceanographic attention on Isopora. Here we provide the first independent high-resolution calibration of both Sr/Ca and δ18O for temperature analyses based on Isopora and demonstrate its consistency with Porites records. We developed modern skeletal Sr/Ca- and δ18O-sea surface temperature (SST) calibrations based on five modern Isopora colonies from Heron Island in the southern GBR. Pairing the coral Sr/Ca record with monthly SST data yielded Sr/Ca-SST sensitivities from -0.061 ± 0.004 (centered) to -0.083 ± 0.007 (raw) mmol/mol °C-1 based on reduced major axis regressions. These sensitivities are in the middle of the range of published Porites values and overlap most published values for Isopora, -0.075 ± 0.011 to -0.065 ± 0.011 mmol/mol °C-1. The δ18O-SST sensitivities range from -0.184 ± 0.014 (centered) to -0.185 ± 0.014 (raw) ‰ °C-1, assuming that all seasonal variation in δ18O was due to SST. These δ18O-SST sensitivities are smaller than the widely accepted value of -0.23‰ °C-1 for biogenic aragonite but are at the upper end of high-resolution Porites-defined sensitivities that are consistently less than the aforementioned established value. Our results validate the use of Isopora as an alternative source of paleoceanographic records in habitats where large massive Porites are scarce or absent.

  15. Investigations of surface related electronic properties in SmB6 and LaAlO3/SrTiO3 heterostructures

    Science.gov (United States)

    Adhikari, Sanjay

    This dissertation reports research performed on two types of two-dimensional. systems: SmB6 and LaAlO3/SrTiO3 (LAO/STO). SmB6 has been proposed to be. a topological Kondo insulator at low temperature. In order to understand carriers/. lattice dynamics and their interactions, femtosecond pump-probe spectroscopy. is performed in SmB6 single crystals and thin lms at variable temperatures. The. collective oscillation modes in GHz - THz and the change of carrier relaxations is. observed as a function of temperature. From the temperature dependent results. f 􀀀?d hybridization, opening of the hybridization gap, phonon bottleneck", and th. possible topological surface state formation is revealed. The topological surface state. should support helical Dirac dispersion with momentum-spin lockage. This dissertation. reports on current injection in SmB6 thin lm with circularly polarized light. at oblique incidence. This spin polarized photocurrent is concluded to be a direct. result of spin momentum lockage in SmB6. LAO/STO interface shows 2-dimensional electron gas (2DEG) at the interface. when the thickness of LAO is more than 3 unit cell. Carrier properties at the. LAO/STO interfaces are highly sensitive to the top surface termination of LAO. The spontaneous dissociation of water on LAO surface is systematically studied by. density functional theory and experimental surface characterizations. Extrinsic effects. from surface adsorbates were often ignored in the previous studies of the 2DEG. From the experiments, it is found that the dissociated water molecules, especially the. surface protons, strongly aect the interface density of states, electron distributions. and lattice distortions. The investigations also reveal the importance of additional. molecular water layers. These additional water layers, through hydrogen bonds, provide. an energetically feasible pathway for manipulating the surface-bonded protons. and thus, the interface electrical characteristics.

  16. Renewal processes

    CERN Document Server

    Mitov, Kosto V

    2014-01-01

    This monograph serves as an introductory text to classical renewal theory and some of its applications for graduate students and researchers in mathematics and probability theory. Renewal processes play an important part in modeling many phenomena in insurance, finance, queuing systems, inventory control and other areas. In this book, an overview of univariate renewal theory is given and renewal processes in the non-lattice and lattice case are discussed. A pre-requisite is a basic knowledge of probability theory.

  17. Oxygen surface exchange kinetics measurement by simultaneous optical transmission relaxation and impedance spectroscopy: Sr(Ti,Fe)O3-x thin film case study.

    Science.gov (United States)

    Perry, Nicola H; Kim, Jae Jin; Tuller, Harry L

    2018-01-01

    We compare approaches to measure oxygen surface exchange kinetics, by simultaneous optical transmission relaxation (OTR) and AC-impedance spectroscopy (AC-IS), on the same mixed conducting SrTi 0.65 Fe 0.35 O 3-x film. Surface exchange coefficients were evaluated as a function of oxygen activity in the film, controlled by gas partial pressure and/or DC bias applied across the ionically conducting yttria-stabilized zirconia substrate. Changes in measured light transmission through the film over time (relaxations) resulted from optical absorption changes in the film corresponding to changes in its oxygen and oxidized Fe (~Fe 4+ ) concentrations; such relaxation profiles were successfully described by the equation for surface exchange-limited kinetics appropriate for the film geometry. The k chem values obtained by OTR were significantly lower than the AC-IS derived k chem values and k q values multiplied by the thermodynamic factor (bulk or thin film), suggesting a possible enhancement in k by the metal current collectors (Pt, Au). Long-term degradation in k chem and k q values obtained by AC-IS was also attributed to deterioration of the porous Pt current collector, while no significant degradation was observed in the optically derived k chem values. The results suggest that, while the current collector might influence measurements by AC-IS, the OTR method offers a continuous, in situ , and contact-free method to measure oxygen exchange kinetics at the native surfaces of thin films.

  18. Oxygen surface exchange kinetics measurement by simultaneous optical transmission relaxation and impedance spectroscopy: Sr(Ti,Fe)O3-x thin film case study

    Science.gov (United States)

    Perry, Nicola H.; Kim, Jae Jin; Tuller, Harry L.

    2018-01-01

    Abstract We compare approaches to measure oxygen surface exchange kinetics, by simultaneous optical transmission relaxation (OTR) and AC-impedance spectroscopy (AC-IS), on the same mixed conducting SrTi0.65Fe0.35O3-x film. Surface exchange coefficients were evaluated as a function of oxygen activity in the film, controlled by gas partial pressure and/or DC bias applied across the ionically conducting yttria-stabilized zirconia substrate. Changes in measured light transmission through the film over time (relaxations) resulted from optical absorption changes in the film corresponding to changes in its oxygen and oxidized Fe (~Fe4+) concentrations; such relaxation profiles were successfully described by the equation for surface exchange-limited kinetics appropriate for the film geometry. The kchem values obtained by OTR were significantly lower than the AC-IS derived kchem values and kq values multiplied by the thermodynamic factor (bulk or thin film), suggesting a possible enhancement in k by the metal current collectors (Pt, Au). Long-term degradation in kchem and kq values obtained by AC-IS was also attributed to deterioration of the porous Pt current collector, while no significant degradation was observed in the optically derived kchem values. The results suggest that, while the current collector might influence measurements by AC-IS, the OTR method offers a continuous, in situ, and contact-free method to measure oxygen exchange kinetics at the native surfaces of thin films. PMID:29511391

  19. Temperature-dependent surface structure, composition, and electronic properties of the clean SrTiO3(111) crystal face: Low-energy-electron diffraction, Auger-electron spectroscopy, electron energy loss, and ultraviolet-photoelectron spectroscopy studies

    International Nuclear Information System (INIS)

    Lo, W.J.; Somorjai, G.A.

    1978-01-01

    Low-energy-electron diffraction, Auger-electron spectroscopy, electron-energy-loss, and ultraviolet-photoelectron spectroscopies were used to study the structure, composition, and electron energy distribution of a clean single-crystal (111) face of strontium titanate (perovskite). The dependence of the surface chemical composition on the temperature has been observed along with corresponding changes in the surface electronic properties. High-temperature Ar-ion bombardment causes an irreversible change in the surface structure, stoichiometry, and electron energy distribution. In contrast to the TiO 2 surface, there are always significant concentrations of Ti 3+ in an annealed ordered SrTiO 3 (111) surface. This stable active Ti 3+ monolayer on top of a substrate with large surface dipole potential makes SrTiO 3 superior to TiO 2 when used as a photoanode in the photoelectrochemical cell

  20. Chemistry data from surface ecosystems in Forsmark and Laxemar-Simpevarp. Site specific data used for estimation of CR and Kd values in SR-Site

    International Nuclear Information System (INIS)

    Troejbom, Mats; Norden, Sara

    2010-11-01

    This report is a background report for the biosphere analysis of the SR-Site Safety Assessment. This work aims to compile information from the Forsmark and Laxemar-Simpevarp sites in order to select and provide relevant site data for parameter sed in the Radionuclide Dose Model. This report contains an overview of all available chemistry data from the surface ecosystems at Forsmark and Laxemar-Simpevarp areas, comprising hydrochemistry of shallow groundwater, porewater, lake water, stream water and sea water as well as the chemical composition of the regolith and biota of the terrestrial, limnic and marine ecosystems. Detailed references to data reports are tabulated and all sampling points are shown in a large number of maps in Chapter 2. An explorative analysis in Chapter 3 is the basis for the final selection of site data described in Chapter 4

  1. Renewable energy

    DEFF Research Database (Denmark)

    Olsen, Birgitte Egelund

    2016-01-01

    Renewable energy projects are increasingly confronted by local opposition, which delays and sometimes even prevents their implementation. This reflects the frequent gap between support for the general idea of renewables as a strategy for reducing carbon emissions, and acceptance of renewable energy...

  2. Anomalous Interface and Surface Strontium Segregation in (La 1– y Sr y ) 2 CoO 4±δ /La 1– x Sr x CoO 3−δ Heterostructured Thin Films

    KAUST Repository

    Feng, Zhenxing

    2014-03-20

    Heterostructured oxides have shown unusual electrochemical properties including enhanced catalytic activity, ion transport, and stability. In particular, it has been shown recently that the activity of oxygen electrocatalysis on the Ruddlesden-Popper/perovskite (La1-ySr y)2CoO4±δ/La1-xSr xCoO3-δ heterostructure is remarkably enhanced relative to the Ruddlesden-Popper and perovskite constituents. Here we report the first atomic-scale structure and composition of (La1-ySr y)2CoO4±δ/La1-xSr xCoO3-δ grown on SrTiO3. We observe anomalous strontium segregation from the perovskite to the interface and the Ruddlesden-Popper phase using direct X-ray methods as well as with ab initio calculations. Such Sr segregation occurred during the film growth, and no significant changes were found upon subsequent annealing in O2. Our findings provide insights into the design of highly active catalysts for oxygen electrocatalysis. © 2014 American Chemical Society.

  3. Anomalous Interface and Surface Strontium Segregation in (La 1– y Sr y ) 2 CoO 4±δ /La 1– x Sr x CoO 3−δ Heterostructured Thin Films

    KAUST Repository

    Feng, Zhenxing; Yacoby, Yizhak; Gadre, Milind J.; Lee, Yueh-Lin; Hong, Wesley T.; Zhou, Hua; Biegalski, Michael D.; Christen, Hans M.; Adler, Stuart B.; Morgan, Dane; Shao-Horn, Yang

    2014-01-01

    Heterostructured oxides have shown unusual electrochemical properties including enhanced catalytic activity, ion transport, and stability. In particular, it has been shown recently that the activity of oxygen electrocatalysis on the Ruddlesden-Popper/perovskite (La1-ySr y)2CoO4±δ/La1-xSr xCoO3-δ heterostructure is remarkably enhanced relative to the Ruddlesden-Popper and perovskite constituents. Here we report the first atomic-scale structure and composition of (La1-ySr y)2CoO4±δ/La1-xSr xCoO3-δ grown on SrTiO3. We observe anomalous strontium segregation from the perovskite to the interface and the Ruddlesden-Popper phase using direct X-ray methods as well as with ab initio calculations. Such Sr segregation occurred during the film growth, and no significant changes were found upon subsequent annealing in O2. Our findings provide insights into the design of highly active catalysts for oxygen electrocatalysis. © 2014 American Chemical Society.

  4. Absence of Ni on the outer surface of Sr doped La 2 NiO 4 single crystals

    KAUST Repository

    Burriel, Mó nica; Wilkins, Stuart; Hill, John P.; Muñ oz-Má rquez, Miguel A.; Brongersma, Hidde H.; Kilner, John A.; Ryan, Mary P.; Skinner, Stephen J.

    2014-01-01

    A combination of surface sensitive techniques was used to determine the surface structure and chemistry of La2-xSrxNiO 4+δ. These measurements unequivocally showed that Ni is not present in the outermost atomic layer, suggesting that the accepted model with the B-site cations exposed to the environment is incorrect. © 2014 The Royal Society of Chemistry.

  5. Understanding the influence of surface chemical states on the dielectric tunability of sputtered Ba0.5Sr0.5TiO3 thin films

    International Nuclear Information System (INIS)

    Venkata Saravanan, K; James Raju, K C

    2014-01-01

    The surface chemical states of RF-magnetron sputtered Ba 0.5 Sr 0.5 TiO 3 (BST5) thin films deposited at different oxygen mixing percentage (OMP) was examined by x-ray photoelectron spectroscopy. The O1s XPS spectra indicate the existence of three kinds of oxygen species (dissociated oxygen ion O 2 − , adsorbed oxide ion O − and lattice oxide ion O 2− ) on the films’ surface, which strongly depends on OMP. The presence of oxygen species other than lattice oxygen ion makes the films’ surface highly reactivity to atmospheric gases, resulting in the formation of undesired surface layers. The XPS results confirm the formation of surface nitrates for the films deposited under oxygen deficient atmosphere (OMP not ≦ 25%), whereas the films deposited in oxygen rich atmosphere (OMP not ≧ 75%) show the presence of metal-hydroxide. The influence of a surface dead layer on the tunable dielectric properties of BST5 films have been studied in detail and are reported. Furthermore, our observations indicate that an optimum ratio of Ar:O 2 is essential for achieving desired material and dielectric properties in BST5 thin films. The films deposited at 50% OMP have the highest dielectric tunability of ∼65% (@280 kV cm −1 ), with good ϵ r -E curve symmetry of 98% and low tan δ of 0.018. The figure of merit for these films is about 35, which is promising for frequency agile device applications. (papers)

  6. Magnetism, Spin Texture, and In-Gap States: Atomic Specialization at the Surface of Oxygen-Deficient SrTiO_{3}.

    Science.gov (United States)

    Altmeyer, Michaela; Jeschke, Harald O; Hijano-Cubelos, Oliver; Martins, Cyril; Lechermann, Frank; Koepernik, Klaus; Santander-Syro, Andrés F; Rozenberg, Marcelo J; Valentí, Roser; Gabay, Marc

    2016-04-15

    Motivated by recent spin- and angular-resolved photoemission (SARPES) measurements of the two-dimensional electronic states confined near the (001) surface of oxygen-deficient SrTiO_{3}, we explore their spin structure by means of ab initio density functional theory (DFT) calculations of slabs. Relativistic nonmagnetic DFT calculations display Rashba-like spin winding with a splitting of a few meV and when surface magnetism on the Ti ions is included, bands become spin-split with an energy difference ∼100  meV at the Γ point, consistent with SARPES findings. While magnetism tends to suppress the effects of the relativistic Rashba interaction, signatures of it are still clearly visible in terms of complex spin textures. Furthermore, we observe an atomic specialization phenomenon, namely, two types of electronic contributions: one is from Ti atoms neighboring the oxygen vacancies that acquire rather large magnetic moments and mostly create in-gap states; another comes from the partly polarized t_{2g} itinerant electrons of Ti atoms lying further away from the oxygen vacancy, which form the two-dimensional electron system and are responsible for the Rashba spin winding and the spin splitting at the Fermi surface.

  7. Renewable enthusiasm

    International Nuclear Information System (INIS)

    Duffin, Tony

    2000-01-01

    A reduction in energy consumption by the energy intensive sectors will be rewarded by a tax credit. The advantages of renewable sources of energy in terms of reducing emissions of carbon dioxide are extolled. The Government will reward the use of renewables through exemption from the Climate Change Levy. Many major companies are now committed to renewables and Shell predict that 50% of world energy will come from renewables by 2050. World-wide there is now 10,000 MW of installed wind power and the annual rate of growth is more than 20%. Other renewables such as biomass, energy from waste, solar power, hydropower, wind power and tidal power are discussed. The Government would like to see 10% of the UK's electricity coming from renewables by 2010. (UK)

  8. Renewable energy

    International Nuclear Information System (INIS)

    Yoon, Cheon Seok

    2009-09-01

    This book tells of renewable energy giving description of environment problem, market of renewable energy and vision and economics of renewable energy. It also deals with solar light like solar cell, materials performance, system and merit of solar cell, solar thermal power such as solar cooker and solar collector, wind energy, geothermal energy, ocean energy like tidal power and ocean thermal energy conversion, fuel cell and biomass.

  9. Evolution of the SrTiO{sub 3} surface electronic state as a function of LaAlO{sub 3} overlayer thickness

    Energy Technology Data Exchange (ETDEWEB)

    Plumb, N.C.; Kobayashi, M. [Swiss Light Source, Paul Scherrer Insitut, CH-5232 Villigen PSI (Switzerland); Salluzzo, M. [CNR-SPIN, Complesso Universitario Monte S. Angelo, Via Cinthia, I-80126 Napoli (Italy); Razzoli, E.; Matt, C.E.; Strocov, V.N.; Zhou, K.J.; Shi, M. [Swiss Light Source, Paul Scherrer Insitut, CH-5232 Villigen PSI (Switzerland); Mesot, J. [Paul Scherrer Institut, CH-5232 Villigen PSI (Switzerland); Institut de la Matiere Complexe, EPF Lausanne, CH-1015 Lausanne (Switzerland); Laboratory for Solid State Physics, ETH Zürich, CH-8093 Zürich (Switzerland); Schmitt, T. [Swiss Light Source, Paul Scherrer Insitut, CH-5232 Villigen PSI (Switzerland); Patthey, L. [Swiss Light Source, Paul Scherrer Insitut, CH-5232 Villigen PSI (Switzerland); SwissFEL, Paul Scherrer Institut, CH-5232 Villigen PSI (Switzerland); Radović, M., E-mail: milan.radovic@psi.ch [Swiss Light Source, Paul Scherrer Insitut, CH-5232 Villigen PSI (Switzerland); Institut de la Matiere Complexe, EPF Lausanne, CH-1015 Lausanne (Switzerland); SwissFEL, Paul Scherrer Institut, CH-5232 Villigen PSI (Switzerland)

    2017-08-01

    Highlights: • The close similarities in the electronic structures of the metallic bare surface of STO and the buried interfaces (LAO/STO). • The similar spectroscopic responses of these systems to photon irradiation. • The emergence of 2 × 1 structural ordering in sufficiently thick LAO/STO interfaces. - Abstract: The novel electronic properties emerging at interfaces between transition metal oxides, and in particular the discovery of conductivity in heterostructures composed of LaAlO{sub 3} (LAO) and SrTiO{sub 3} (STO) band insulators, have generated new challenges and opportunities in condensed matter physics. Although the interface conductivity is stabilized when LAO matches or exceeds a critical thickness of 4 unit cells (uc), other phenomena such as a universal metallic state found on the bare surface of STO single crystals and persistent photon-triggered conductivity in otherwise insulating STO-based interfaces raise important questions about the role of the LAO overlayer and the possible relations between vacuum/STO and LAO/STO interfaces. Here, using angle-resolved photoemission spectroscopy (ARPES) on in situ prepared samples complemented by resonant inelastic X-ray scattering (RIXS), we study how the metallic STO surface state evolves during the growth of a crystalline LAO overlayer. In all the studied samples, the character of the conduction bands, their carrier densities, the Ti{sup 3+} crystal field, and the response to photon irradiation bear strong similarities. Nevertheless, we report here that studied LAO/STO interfaces exhibit an instability toward an apparent 2 × 1 folding of the Fermi surface at and above a 4 uc thickness threshold, which distinguishes these heterostructures from bare STO and sub-critical-thickness LAO/STO.

  10. License renewal

    International Nuclear Information System (INIS)

    Newberry, S.

    1993-01-01

    This article gives an overview of the process of license renewal for nuclear power plants. It explains what is meant by license renewal, the significance of license renewal, and goes over key elements involved in the process of license renewal. Those key elements are NRC requirements embodied in 10 CFR Part 54 (Reactor Safety) and 10 CFR Part 51 (Environmental Issues). In addition Industry Reports must be developed and reviewed. License renewal is essentially the process of applying for a 20 year extension to the original 40 year operating license granted for the plant. This is a very long term process, which involves a lot of preparation, and compliance with regulatory rules and guidelines. In general it is a process which is expected to begin when plants reach an operating lifetime of 20 years. It has provisions for allowing the public to become involved in the review process

  11. Renewable Energy

    DEFF Research Database (Denmark)

    Sørensen, Bent Erik

    Bent Sorensen’s Renewable Energy: Physics, Engineering, Environmental Impacts, Economics and Planning, Fifth Edition, continues the tradition by providing a thorough and current overview of the entire renewable energy sphere. Since its first edition, this standard reference source helped put...... renewable energy on the map of scientific agendas. Several renewable energy solutions no longer form just a marginal addition to energy supply, but have become major players, with the promise to become the backbone of an energy system suitable for life in the sustainability lane. This volume is a problem...... structured around three parts in order to assist readers in focusing on the issues that impact them the most for a given project or question. PART I covers the basic scientific principles behind all major renewable energy resources, such as solar, wind, and biomass. PART II provides in-depth information...

  12. In Situ Studies of the Temperature-Dependent Surface Structure and Chemistry of Single-Crystalline (001)-Oriented La 0.8 Sr 0.2 CoO 3−δ Perovskite Thin Films

    KAUST Repository

    Feng, Zhenxing; Crumlin, Ethan J.; Hong, Wesley T.; Lee, Dongkyu; Mutoro, Eva; Biegalski, Michael D.; Zhou, Hua; Bluhm, Hendrik; Christen, Hans M.; Shao-Horn, Yang

    2013-01-01

    Perovskites are used to promote the kinetics of oxygen electrocatalysis in solid oxide fuel cells and oxygen permeation membranes. Little is known about the surface structure and chemistry of perovskites at high temperatures and partial oxygen pressures. Combining in situ X-ray reflectivity (XRR) and in situ ambient pressure X-ray photoelectron spectroscopy (APXPS), we report, for the first time, the evolution of the surface structure and chemistry of (001)-oriented perovskite La0.8Sr0.2CoO 3-δ (LSC113) and (La0.5Sr 0.5)2CoO4+δ (LSC214)-decorated LSC113 (LSC113/214) thin films as a function of temperature. Heating the (001)-oriented LSC113 surface leads to the formation of surface LSC214-like particles, which is further confirmed by ex situ Auger electron spectroscopy (AES). In contrast, the LSC113/214 surface, with activities much higher than that of LSC 113, is stable upon heating. Combined in situ XRR and APXPS measurements support that Sr enrichment may occur at the LSC113 and LSC214 interface, which can be responsible for its markedly enhanced activities. © 2013 American Chemical Society.

  13. In Situ Studies of the Temperature-Dependent Surface Structure and Chemistry of Single-Crystalline (001)-Oriented La 0.8 Sr 0.2 CoO 3−δ Perovskite Thin Films

    KAUST Repository

    Feng, Zhenxing

    2013-05-02

    Perovskites are used to promote the kinetics of oxygen electrocatalysis in solid oxide fuel cells and oxygen permeation membranes. Little is known about the surface structure and chemistry of perovskites at high temperatures and partial oxygen pressures. Combining in situ X-ray reflectivity (XRR) and in situ ambient pressure X-ray photoelectron spectroscopy (APXPS), we report, for the first time, the evolution of the surface structure and chemistry of (001)-oriented perovskite La0.8Sr0.2CoO 3-δ (LSC113) and (La0.5Sr 0.5)2CoO4+δ (LSC214)-decorated LSC113 (LSC113/214) thin films as a function of temperature. Heating the (001)-oriented LSC113 surface leads to the formation of surface LSC214-like particles, which is further confirmed by ex situ Auger electron spectroscopy (AES). In contrast, the LSC113/214 surface, with activities much higher than that of LSC 113, is stable upon heating. Combined in situ XRR and APXPS measurements support that Sr enrichment may occur at the LSC113 and LSC214 interface, which can be responsible for its markedly enhanced activities. © 2013 American Chemical Society.

  14. Coral growth rings and the temporal history of nuclear 14C/C and 90Sr/Sr in the surface ocean: Final report, June 1, 1982-December 31, 1984

    International Nuclear Information System (INIS)

    Broecker, W.S.; Cember, R.P.; Toggweiler, J.R.; Trumbore, S.E.; White, J.

    1987-08-01

    This report summarizes the history and scientific results of the Lamont-Doherty Geological Observatory coral radioisotope project. The report includes abstracts of works in the literature or in preparation resulting from the coral project and a complete listing of the radiocarbon and 90 Sr data measured in the course of the project. Also, some possible future research directions for the coral project are suggested

  15. Renewable energy

    International Nuclear Information System (INIS)

    Berghmans, J.

    1994-01-01

    Renewable energy sources have a small environmental impact and can be easily integrated within existing structures. Moreover, the use of renewable energy sources can contribute to achieve a zero emission of carbon dioxide by 2100, provided an efficient environmental policy during the next 40 years. This includes a correct pricing policy of renewable energy sources with respect to nuclear energy and fossil fuel. The latter energy sources have been favoured in the past. In addition, an open market policy, the restructuring or conversion of existing international energy institutes, and international treaties for the protection of the natural environment are needed in view of achieving the zero carbon dioxide emission objective. (A.S.)

  16. Optimization of 90Sr/89Sr measurements

    Directory of Open Access Journals (Sweden)

    Legarda F.

    2012-04-01

    Full Text Available One of the key points in the double measurement method for the measurement of both, 89Sr and 90Sr, by using a proportional counter is the choice of the times at which the measurements should be done. In this paper, the formulae to calculate the 89Sr and 90Sr detection limits in conditions of radioactive equilibrium between 90Y and 90Sr are derived, and an analysis of them as a function of the time between the two measurements is done. The choice for the time of the second measurement is going to depend on the desired quality of the results to be obtained.

  17. Renewable energy.

    Science.gov (United States)

    Destouni, Georgia; Frank, Harry

    2010-01-01

    The Energy Committee of the Royal Swedish Academy of Sciences has in a series of projects gathered information and knowledge on renewable energy from various sources, both within and outside the academic world. In this article, we synthesize and summarize some of the main points on renewable energy from the various Energy Committee projects and the Committee's Energy 2050 symposium, regarding energy from water and wind, bioenergy, and solar energy. We further summarize the Energy Committee's scenario estimates of future renewable energy contributions to the global energy system, and other presentations given at the Energy 2050 symposium. In general, international coordination and investment in energy research and development is crucial to enable future reliance on renewable energy sources with minimal fossil fuel use.

  18. Chernobyl 90Sr in bilberries from Poland

    International Nuclear Information System (INIS)

    Mietelski, J.W.; Vajda, N.

    1997-01-01

    As part of a detailed survey on the contamination of Polish forests 90 Sr activity concentrations were determined in bilberries. Elevated 90 Sr levels were found in several samples from north-eastern Poland. The calculated maximum 90 Sr surface contamination was 2 kBq*m -2 . The correlation between 90 Sr and 137 Cs concentrations in bilberries was good for two sets of samples originating from two geographical areas of Poland indicating the local differences in radionuclide depositions from Chernobyl fallout. (author)

  19. Influence of ionic conductivity of the nano-particulate coating phase on oxygen surface exchange of La0.58Sr0.4Co0.2Fe0.8O3-δ

    NARCIS (Netherlands)

    Saher, S.; Naqash, S.; Boukamp, Bernard A.; Hu, Bobing; Xia, Changrong; Bouwmeester, Henricus J.M.

    2017-01-01

    The oxygen surface exchange kinetics of mixed-conducting perovskite La0.58Sr0.4Co0.2Fe0.8O3 d (LSCF) ceramics coated with a porous nano-particulate layer of either gadolinea (Gd2O3), ceria (CeO2) or 20 mol% Gd-doped ceria (GCO) was determined by electrical conductivity relaxation (ECR). The

  20. Renewable energy

    DEFF Research Database (Denmark)

    Olsen, Birgitte Egelund

    2016-01-01

    Renewable energy projects are increasingly confronted by local opposition, which delays and sometimes even prevents their implementation. This reflects the frequent gap between support for the general idea of renewables as a strategy for reducing carbon emissions, and acceptance of renewable energy...... installations in the local landscape. A number of countries have introduced financial incentives to promote community acceptance. The tool box of incentives is still limited but in recent years it has been expanded to address local concerns. Certain general characteristics can be identified, suggesting...... that there are at least three distinct categories of incentives: individual compensation, community benefits and ownership measures. Local opposition must be approached with caution, as financial incentives to promote local acceptance can be seen as buying consent or even ‘bribery’, stirring up further opposition....

  1. Plasma Glow Discharge as a Tool for Surface Modification of Catalytic Solid Oxides: A Case Study of La0.6Sr0.4Co0.2Fe0.8O3−δ Perovskite

    Directory of Open Access Journals (Sweden)

    Yanxiang Zhang

    2016-09-01

    Full Text Available Performance of solid oxide fuel cells (SOFCs is hindered by the sluggish catalytic kinetics on the surfaces of cathode materials. It has recently been reported that improved electrochemical activity of perovskite oxides can be obtained with the cations or the oxides of some metallic elements at the surface. Here, we used a cost-effective plasma glow charge method as a generic tool to deposit nano-size metallic particles onto the surface of SOFC materials. Ni nano-scale patterns were successfully coated on the La0.6Sr0.4Co0.2Fe0.8O3−δ (LSCF surface. The microstructure could be well controlled. The kinetics of oxygen exchange on the modified LSCF surface was promoted significantly, confirmed by electrical conductivity relaxation (ECR measurement.

  2. X-ray photoelectron spectroscopy study of the surface of solid electrolyte La0.88Sr0.12Ga0.82Mg0.18O3-α

    International Nuclear Information System (INIS)

    Shkerin, S.N.; Kalashnikova, N.A.; Kuznetsov, M.V.

    2003-01-01

    The composition and chemical state of elements on the surface of solid oxygen-conducting electrolyte La 0.88 Sr 0.12 Ga 0.82 Mg 0.18 O 3-α prior to and after high-temperature annealing (T = 973 K) in CO 2 atmosphere were studied by the method of X-ray photoelectron spectroscopy. It is shown that products of interaction between doped lanthanum gallate and carbon dioxide are localized in the surface layer 8-10 nm thick. Annealing in CO 2 atmosphere does not involve formation of carbon chemical compounds with metals on the electrolyte surface. Surface layers both in the initial electrolyte and after allowance to stay in CO 2 were enriched by strontium oxide, lanthanum hydroxide being present on the surface [ru

  3. Renewable Energy

    NARCIS (Netherlands)

    Turkenburg, W.C.; Arent, D.; Bertani, R.; Faaij, A.P.C.; Hand, M.; Krewitt, W.; Larson, E.D.; Lund, J.; Mehos, M.; Merrigan, T.; Mitchell, C.; Moreira, J.R.; Sinke, W.C.; Sonntag-O'Brien, V.; Thresher, B.; Sark, W.G.J.H.M. van; Usher, E.

    2012-01-01

    This chapter presents an in-depth examination of major renewable energy technologies, including their installed capacity and energy supply in 2009 , the current state of market and technology development, their economic and financial feasibility in 2009 and in the near future, as well as major

  4. Tuning the electronic properties of LaAlO3/SrTiO3 interfaces by irradiating the LaAlO3 surface with low-energy cluster ion beams

    Science.gov (United States)

    Ridier, Karl; Aureau, Damien; Bérini, Bruno; Dumont, Yves; Keller, Niels; Vigneron, Jackie; Etcheberry, Arnaud; Domengès, Bernadette; Fouchet, Arnaud

    2018-01-01

    We have investigated the effects of low-energy ion beam irradiations using argon clusters on the chemical and electronic properties of LaAlO3/SrTiO3 (LAO/STO) heterointerfaces by combining x-ray photoelectron spectroscopy (XPS) and electrical transport measurements. Due to its unique features, we demonstrate that a short-time cluster ion irradiation of the LAO surface induces significant modifications in the chemical properties of the buried STO substrate with (1) a lowering of Ti atoms oxidation states (from Ti4 + to Ti3 + and Ti2 +) correlated to the formation of oxygen vacancies at the LAO surface and (2) the creation of new surface states for Sr atoms. Contrary to what is generally observed by using higher energy ion beam techniques, this leads to an increase of the electrical conductivity at the LAO/STO interface. Our XPS data clearly reveal the existence of dynamical processes on the titanium and strontium atoms, which compete with the effect of the cluster ion beam irradiation. These relaxation effects are in part attributed to the diffusion of the ion-induced oxygen vacancies in the entire heterostructure since an increase of the interfacial metallicity is also evidenced far from the irradiated area. This paper highlights the possibility of tuning the electrical properties of LAO/STO interfaces by surface engineering, confirming experimentally the intimate connection between LAO chemistry and electronic properties of LAO/STO interfaces.

  5. Comparative Study on Assimilating Remote Sensing High Frequency Radar Surface Currents at an Atlantic Marine Renewable Energy Test Site

    Directory of Open Access Journals (Sweden)

    Lei Ren

    2017-12-01

    Full Text Available A variety of data assimilation approaches have been applied to enhance modelling capability and accuracy using observations from different sources. The algorithms have varying degrees of complexity of implementation, and they improve model results with varying degrees of success. Very little work has been carried out on comparing the implementation of different data assimilation algorithms using High Frequency radar (HFR data into models of complex inshore waters strongly influenced by both tides and wind dynamics, such as Galway Bay. This research entailed implementing four different data assimilation algorithms: Direct Insertion (DI, Optimal Interpolation (OI, Nudging and indirect data assimilation via correcting model forcing into a three-dimensional hydrodynamic model and carrying out detailed comparisons of model performances. This work will allow researchers to directly compare four of the most common data assimilation algorithms being used in operational coastal hydrodynamics. The suitability of practical data assimilation algorithms for hindcasting and forecasting in shallow coastal waters subjected to alternate wetting and drying using data collected from radars was assessed. Results indicated that a forecasting system of surface currents based on the three-dimensional model EFDC (Environmental Fluid Dynamics Code and the HFR data using a Nudging or DI algorithm was considered the most appropriate for Galway Bay. The largest averaged Data Assimilation Skill Score (DASS over the ≥6 h forecasting period from the best model NDA attained 26% and 31% for east–west and north–south surface velocity components respectively. Because of its ease of implementation and its accuracy, this data assimilation system can provide timely and useful information for various practical coastal hindcast and forecast operations.

  6. Near-surface effects of transient oxidation and reduction on Nb-doped SrTiO3 epitaxial thin films

    Science.gov (United States)

    Chang, C. F.; Chen, Q. Y.; Wadekar, P. V.; Lozano, O.; Wong, M. S.; Hsieh, W. C.; Lin, W. Y.; Ko, H. H.; Lin, Q. J.; Huang, H. C.; Ho, N. J.; Tu, L. W.; Liao, H. H.; Chinta, P. V.; Chu, W. K.; Seo, H. W.

    2014-03-01

    We studied the effects of transient oxidation and reduction of Nb-doped epitaxial thin films through variations of PAr and PO2. The samples were prepared by co-sputtering of Nb and SrTiO3 on LaAlO3 substrates. The Nb-content were varied from 0-33.7%, as determined by PIXE. Contact resistance, sheet resistance, and optical properties are used to discriminate the effects.

  7. Surface morphology and in-plane-epitaxy of SmBa2Cu3O7-δ films on SrTiO3 (001) substrates studied by STM and grazing incidence x-ray diffraction

    DEFF Research Database (Denmark)

    Jiang, Q.D.; Smilgies, D.M.; Feidenhans'l, R.

    1996-01-01

    The surface morphology and in-plane epitaxy of thin films of SmBa(2)Cu3O(7-delta) (Sm-BCO) grown on SrTiO3 (001) substrates with various thicknesses have been investigated by scanning tunneling microscopy (STM) and grazing incidence x-ray diffraction (GIXRD). As revealed by GIXRD, SmBCO films as ...... films above h(c2), introduction of screw dislocations leads to spiral growth.......The surface morphology and in-plane epitaxy of thin films of SmBa(2)Cu3O(7-delta) (Sm-BCO) grown on SrTiO3 (001) substrates with various thicknesses have been investigated by scanning tunneling microscopy (STM) and grazing incidence x-ray diffraction (GIXRD). As revealed by GIXRD, SmBCO films...... substrate. Three different types of surface morphology were observed by STM with increasing film thickness h: a) 2D growth for hh(c2). With GIXRD, a density modulation is observed in the films with a thickness below h(c2). For thicker...

  8. Metastable honeycomb SrTiO_3/SrIrO_3 heterostructures

    International Nuclear Information System (INIS)

    Anderson, T. J.; Ryu, S.; Podkaminer, J. P.; Ma, Y.; Eom, C. B.; Zhou, H.; Xie, L.; Irwin, J.; Rzchowski, M. S.; Pan, X. Q.

    2016-01-01

    Recent theory predictions of exotic band topologies in (111) honeycomb perovskite SrIrO_3 layers sandwiched between SrTiO_3 have garnered much attention in the condensed matter physics and materials communities. However, perovskite SrIrO_3 film growth in the (111) direction remains unreported, as efforts to synthesize pure SrIrO_3 on (111) perovskite substrates have yielded films with monoclinic symmetry rather than the perovskite structure required by theory predictions. In this study, we report the synthesis of ultra-thin metastable perovskite SrIrO_3 films capped with SrTiO_3 grown on (111) SrTiO_3 substrates by pulsed laser deposition. The atomic structure of the ultra-thin films was examined with scanning transmission electron microscopy (STEM), which suggests a perovskite layering distinct from the bulk SrIrO_3 monoclinic phase. In-plane 3-fold symmetry for the entire heterostructure was confirmed using synchrotron surface X-ray diffraction to measure symmetry equivalent crystal truncation rods. Our findings demonstrate the ability to stabilize (111) honeycomb perovskite SrIrO_3, which provides an experimental avenue to probe the phenomena predicted for this material system.

  9. The renewable alternative

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This chapter discusses renewable energy sources as an alternative to a fossil fuel based economy. The topics discussed in the chapter include the historic aspects and current status of use of renewable energy, status of the renewable energy industry, market barriers to renewable energy, research and development and commercialization of renewable energy, the environmental and social costs associated with renewable energy, valuing future costs and benefits of energy use, and the potential market of renewable energy

  10. Effect of atmospheric CO{sub 2} on surface segregation and phase formation in La{sub 0.6}Sr{sub 0.4}Co{sub 0.2}Fe{sub 0.8}O{sub 3−δ} thin films

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Yang [Division of Materials Science and Engineering, Boston University, Brookline, MA 02446 (United States); Luo, Heng [Department of Mechanical Engineering, Boston University, Boston, MA 02215 (United States); Cetin, Deniz [Division of Materials Science and Engineering, Boston University, Brookline, MA 02446 (United States); Lin, Xi [Division of Materials Science and Engineering, Boston University, Brookline, MA 02446 (United States); Department of Mechanical Engineering, Boston University, Boston, MA 02215 (United States); Ludwig, Karl [Division of Materials Science and Engineering, Boston University, Brookline, MA 02446 (United States); Department of Physics, Boston University, Boston, MA 02215 (United States); Pal, Uday; Gopalan, Srikanth [Division of Materials Science and Engineering, Boston University, Brookline, MA 02446 (United States); Department of Mechanical Engineering, Boston University, Boston, MA 02215 (United States); Basu, Soumendra, E-mail: basu@bu.edu [Division of Materials Science and Engineering, Boston University, Brookline, MA 02446 (United States); Department of Mechanical Engineering, Boston University, Boston, MA 02215 (United States)

    2014-12-30

    Highlights: • LSCF exhibits Sr surface segregation on high-temperature annealing. • The presence of atmospheric CO{sub 2} enhances the kinetics of Sr surface segregation. • At high-CO{sub 2} partial pressures, there is a significant coverage of the surface by Sr-rich phases. • The increase in kinetics is attributed to increased thermodynamic driving force for SrCO{sub 3} formation. - Abstract: The effects of atmospheric CO{sub 2} on surface segregation and phase formation in La{sub 0.6}Sr{sub 0.4}Co{sub 0.2}Fe{sub 0.8}O{sub 3−δ} (LSCF-6428) were investigated. (0 0 1)-oriented LSCF-6428 thin films were deposited on lattice matched (1 1 0)-oriented NdGaO{sub 3} (NGO) substrates by pulsed laser deposition (PLD). Using the synchrotron technique of total reflection X-ray fluorescence (TXRF), it was found that the kinetics of Sr surface segregation was enhanced when annealing at 800 °C in a high-CO{sub 2} partial pressure, as compared to a similar anneal in a CO{sub 2}-free atmosphere, with the oxygen partial pressure being constant in both cases. Hard X-ray photoelectron spectroscopy (HAXPES) measurements showed that the contribution of the surface carbonate to surface oxide phases increased significantly for the sample annealed in the high-CO{sub 2} atmosphere. Atomic force microscopy (AFM) studies showed enhanced surface phase formation during the high-CO{sub 2} partial pressure anneal. Density functional theory (DFT) calculations provide a thermodynamic basis for the enhanced kinetics of surface segregation in the presence of atmospheric CO{sub 2}.

  11. Critical Doping for the Onset of Fermi-Surface Reconstruction by Charge-Density-Wave Order in the Cuprate Superconductor La_{2-x}Sr_{x}CuO_{4}

    Directory of Open Access Journals (Sweden)

    S. Badoux

    2016-04-01

    Full Text Available The Seebeck coefficient S of the cuprate superconductor La_{2-x}Sr_{x}CuO_{4} (LSCO was measured in magnetic fields large enough to access the normal state at low temperatures, for a range of Sr concentrations from x=0.07 to x=0.15. For x=0.11, 0.12, 0.125, and 0.13, S/T decreases upon cooling to become negative at low temperatures. The same behavior is observed in the Hall coefficient R_{H}(T. In analogy with other hole-doped cuprates at similar hole concentrations p, the negative S and R_{H} show that the Fermi surface of LSCO undergoes a reconstruction caused by the onset of charge-density-wave modulations. Such modulations have indeed been detected in LSCO by x-ray diffraction in precisely the same doping range. Our data show that in LSCO this Fermi-surface reconstruction is confined to 0.085

  12. Kinetics and Mechanisms of Oxygen Surface Exchange on La0.6Sr0.4FeO3-delta Thin Films

    OpenAIRE

    Mosleh, Majid; Søgaard, Martin; Hendriksen, Peter Vang

    2009-01-01

    The thermodynamic properties as well as oxygen exchange kinetics were examined on mixed ionic and electronic conducting (La0.6Sr0.4)0.99FeO3− (LSF64) thin films deposited on MgO single crystals. It is found that thin films and bulk material have the same oxygen stoichiometry for a given temperature and oxygen partial pressure [i.e., the incorporation reaction has the same reaction enthalpy (H0=−105 KJ/mol) and entropy (S0=−75.5 J/mol/K) as found for bulk material]. The thin film shows smaller...

  13. Environmental 90Sr measurements

    Science.gov (United States)

    Paul, M.; Berkovits, D.; Cecil, L.D.; Feldstein, H.; Hershkowitz, A.; Kashiv, Y.; Vogt, S.

    1997-01-01

    90Sr (T1/2 = 28.5 years) is a long-lived radionuclide produced in nuclear fission. Fast radiochemical detection of 90Sr in environmental samples is not feasible using current analytical methods. Accelerator Mass Spectrometry (AMS) measurements of 90Sr were made with the Rehovot 14UD Pelletron accelerator at a terminal voltage of 11 or 12 MV using our standard detection system. Injection of hydride ions (SrH3-) was chosen owing to high beam intensity and low Coulomb explosion effects. 90Sr ions were identified and discriminated from isobaric 90Zr by measuring time of flight, total energy and three independent energy-loss signals in an ionization chamber. A reference sample and a ground-water sample were successfully measured. The detection limit determined for a laboratory blank by the residual counts in the 90Sr region is 90Sr/Sr = 3 ?? 10-13, corresponding in practice to (2-4) ?? 10790Sr atoms or about 0.5-1 pCi/L in environmental water samples.

  14. nomalous Interface and Surface Strontium Segregation in (La1-ySry)2CoO4 /La1-xSrxCoO3- Heterostructured Thin Films

    Energy Technology Data Exchange (ETDEWEB)

    Feng, Zhenxing [Massachusetts Institute of Technology (MIT); Yacoby, Yuzhak [Massachusetts Institute of Technology (MIT); Gadre, Milind [Massachusetts Institute of Technology (MIT); Lee, Yueh-Lin [Massachusetts Institute of Technology (MIT); Hong, W. [Harvard University; Zhou, Hua [Argonne National Laboratory (ANL); Biegalski, Michael D [ORNL; Christen, Hans M [ORNL; Adler, Stuart [University of Washington; Morgan, Dane [University of Wisconsin, Madison; Shao-Horn, Yang [Massachusetts Institute of Technology (MIT)

    2014-01-01

    Heterostructured materials have shown unusual physiochemical properties at the interfaces such as two dimensional electron gas systems, high-temperature superconductivity, and enhanced catalysis. Here we report the first atomic-scale evidence of the microscopic structure of a perovskite/Ruddlesden-Popper heterostructure (having La1-xSrxCoO3- /(La1-ySry)2CoO4 ), and anomalous strontium segregation at the interface and in the Ruddlesden-Popper structure using direct X-ray methods combined with ab initio calculations. The remarkably enhanced activity of such heterostructured surfaces relative to bulk perovskite and Ruddlesden-Popper oxides previously shown for oxygen electrocatalysis at elevated temperatures can be attributed to reduced thermodynamic penalty of oxygen vacancies in the oxide structure associated with Sr segregation observed in the heterostructure. Our findings provide insights for the design of highly active catalysts for energy conversion and storage applications.

  15. Spatiotemporal Co-variability of Surface Climate for Renewable Energy across the Contiguous United States: Role of the North Atlantic Subtropical High

    Science.gov (United States)

    Doering, K.; Steinschneider, S.

    2017-12-01

    The variability of renewable energy supply and drivers of demand across space and time largely determines the energy balance within power systems with a high penetration of renewable technologies. This study examines the joint spatiotemporal variability of summertime climate linked to renewable energy production (precipitation, wind speeds, insolation) and energy demand (temperature) across the contiguous United States (CONUS) between 1948 and 2015. Canonical correlation analysis is used to identify the major modes of joint variability between summer wind speeds and precipitation and related patterns of insolation and temperature. Canonical variates are then related to circulation anomalies to identify common drivers of the joint modes of climate variability. Results show that the first two modes of joint variability between summer wind speeds and precipitation exhibit pan-US dipole patterns with centers of action located in the eastern and central CONUS. Temperature and insolation also exhibit related US-wide dipoles. The relationship between canonical variates and lower-tropospheric geopotential height indicates that these modes are related to variability in the North Atlantic subtropical high (NASH). This insight can inform optimal strategies for siting renewables in an interconnected electric grid, and has implications for the impacts of climate variability and change on renewable energy systems.

  16. Influence of alkylphosphonic acid grafting on the electronic and magnetic properties of La{sub 2/3}Sr{sub 1/3}MnO{sub 3} surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Galbiati, Marta [Unité Mixte de Physique CNRS-Thales, 1 Av. A. Fresnel, 91767 Palaiseau (France); Université Paris-Sud, 91405 Orsay (France); Tatay, Sergio, E-mail: sergio.tatay@uv.es [Unité Mixte de Physique CNRS-Thales, 1 Av. A. Fresnel, 91767 Palaiseau (France); Université Paris-Sud, 91405 Orsay (France); Instituto de Ciencia Molecular (ICMol), Universitat de Valencia, C. Caterdratico Jose Beltran 2, 46980 Paterna (Spain); Delprat, Sophie [Unité Mixte de Physique CNRS-Thales, 1 Av. A. Fresnel, 91767 Palaiseau (France); Université Paris-Sud, 91405 Orsay (France); UPMC, Université Paris 06, 4 Place Jussieu, 75005 Paris (France); Barraud, Clément; Cros, Vincent; Jacquet, Eric [Unité Mixte de Physique CNRS-Thales, 1 Av. A. Fresnel, 91767 Palaiseau (France); Université Paris-Sud, 91405 Orsay (France); Coloma, Fernando [Servicios Técnicos de Investigación, Universidad de Alicante, E-03080 Alicante (Spain); Choueikani, Fadi; Otero, Edwige; Ohresser, Philippe [Synchrotron SOLEIL, L’Orme des Merisiers, Saint-Aubin, BP 48, FR-91192 Gif-sur-Yvette (France); Haag, Norman; Cinchetti, Mirko; Aeschlimann, Martin [Department of Physics and Research Center OPTIMAS, University of Kaiserslautern, Erwin-Schroedinger Strasse 46, 67663 Kaiserslautern (Germany); Seneor, Pierre, E-mail: pierre.seneor@thalesgroup.com [Unité Mixte de Physique CNRS-Thales, 1 Av. A. Fresnel, 91767 Palaiseau (France); Université Paris-Sud, 91405 Orsay (France); and others

    2015-10-30

    Highlights: • Probe the influence of alkylphosphonic acids-based SAMs on the electronic and magnetic properties of the LSMO. • Measure the modification of the Mn oxidation state of LSMO surface induced by the molecules grafting. • Evaluate the modification of the LSMO work function induced by the alkylphosphonic acids molecules. - Abstract: Self-assembled monolayers (SAMs) are highly promising materials for molecular engineering of electronic and spintronics devices thanks to their surface functionalization properties. In this direction, alkylphosphonic acids have been used to functionalize the most common ferromagnetic electrode in organic spintronics: La{sub 2/3}Sr{sub 1/3}MnO{sub 3} (LSMO). However, a study on the influence of SAMs grafting on LSMO electronic and magnetic properties is still missing. In this letter, we probe the influence of alkylphosphonic acids-based SAMs on the electronic and magnetic properties of the LSMO surface using different spectroscopies. We observe by X-ray photoemission and X-ray absorption that the grafting of the molecules on the LSMO surface induces a reduction of the Mn oxidation state. Ultraviolet photoelectron spectroscopy measurements also show that the LSMO work function can be modified by surface dipoles opening the door to both tune the charge and spin injection efficiencies in organic devices such as organic light-emitting diodes.

  17. Effect of pH values on surface modification and solubility of phosphate bioglass-ceramics in the CaO-P 2O 5-Na 2O-SrO-ZnO system

    Science.gov (United States)

    Li, Xudong; Cai, Shu; Zhang, Wenjuang; Xu, Guohua; Zhou, Wei

    2009-08-01

    The bioactive glass-ceramics in the CaO-P 2O 5-Na 2O-SrO-ZnO system were synthesized by the sol-gel technique, and then chemically treated at different pH values to study the solubility and surface modification. Samples sintered at 650 °C for 4 h consisted of the crystalline phase β-Ca 2P 2O 7 and the glass matrix. After soaking in the solution at pH 1.0, the residual glass matrix on the surface appeared entirely dissolved and no new phase could be detected. Whereas at pH 3.0, web-like layer exhibiting peaks corresponding to CaP 2O 6 was formed and covered the entire surface of the sample. When conducted at pH 10.0, only part of the glass matrix was dissolved and a new phase Ca 4P 6O 19 was precipitated, forming the petaline layer. The chemical treatment can easily change the surface morphologies and phase composition of this bioactive glass-ceramics. The higher level of surface roughness resulting from the new-formed layer would improve the interface bonding and benefit for cell adhesion.

  18. Renewing governance.

    Science.gov (United States)

    Loos, Gregory P

    2003-01-01

    Globalization's profound influence on social and political institutions need not be negative. Critics of globalization have often referred to the "Impossible Trinity" because decision-making must 1. respect national sovereignty, 2. develop and implement firm regulation, and 3. allow capital markets to be as free as possible. To many, such goals are mutually exclusive because history conditions us to view policy-making and governance in traditional molds. Thus, transnational governance merely appears impossible because current forms of governance were not designed to provide it. The world needs new tools for governing, and its citizens must seize the opportunity to help develop them. The rise of a global society requires a greater level of generality and inclusion than is found in most policy bodies today. Politicians need to re-examine key assumptions about government. States must develop ways to discharge their regulatory responsibilities across borders and collaborate with neighboring jurisdictions, multilateral bodies, and business. Concepts such as multilateralism and tripartism show great promise. Governments must engage civil society in the spirit of shared responsibility and democratic decision-making. Such changes will result in a renewal of the state's purpose and better use of international resources and expertise in governance.

  19. Chemistry data from surface ecosystems in Forsmark and Laxemar-Simpevarp. Site specific data used for estimation of CR and K{sub d} values in SR-Site

    Energy Technology Data Exchange (ETDEWEB)

    Troejbom, Mats [Mats Troejbom Konsult AB (Sweden); Norden, Sara [Svensk Kaernbraenslehantering AB (Sweden)

    2010-11-15

    This report is a background report for the biosphere analysis of the SR-Site Safety Assessment. This work aims to compile information from the Forsmark and Laxemar-Simpevarp sites in order to select and provide relevant site data for parameter sed in the Radionuclide Dose Model. This report contains an overview of all available chemistry data from the surface ecosystems at Forsmark and Laxemar-Simpevarp areas, comprising hydrochemistry of shallow groundwater, porewater, lake water, stream water and sea water as well as the chemical composition of the regolith and biota of the terrestrial, limnic and marine ecosystems. Detailed references to data reports are tabulated and all sampling points are shown in a large number of maps in Chapter 2. An explorative analysis in Chapter 3 is the basis for the final selection of site data described in Chapter 4

  20. Strontium (Sr) separation from seawater using titanate adsorbents: Effects of seawater matrix ions on Sr sorption behavior

    Science.gov (United States)

    Ryu, Jungho; Hong, Hye-jin; Ryu, Taegong; Park, In-Su

    2017-04-01

    Strontium (Sr) which has many industrial applications such as ferrite magnet, ceramic, and fire works exists in seawater with the concentration of approximately 7 mg/L. In previous report estimating economic potential on recovery of various elements from seawater in terms of their commercial values and concentrations in seawater, Sr locates upper than approximate break-even line, which implies Sr recovery from seawater can be potentially profitable. Recently, Sr separation from seawater has received great attention in the environmental aspect after Fukushima Nuclear Power Plant (NPP) accident which released much amount of radioactive Sr and Cs. Accordingly, the efficient separation of radioactive elements released to seawater has become critical as an important technological need as well as their removal from radioactive wastes. So far, it has been introduced to separate Sr from aqueous media by various methods including solvent extraction, adsorption by solid materials, and ion exchange. Among them, the adsorption technique using solid adsorbents is of great interest for selectively separating Sr from seawater with respect to low concentration level of Sr. In this study, we synthesized titanate nanotube (TiNT) by simple hydrothermal reaction, characterized its physicochemical properties, and systematically evaluated Sr sorption behavior under various reaction conditions corresponding to seawater environment. The synthesized TiNT exhibited the fibril-type nanotube structure with high specific surface area of 260 m2/g. The adsorption of Sr on TiNT rapidly occurred following pseudo-second-order kinetic model, and was in good agreement with Langmuir isotherm model, indicating maximum adsorption capacity of 97 mg/g. Based on Sr uptake and Na release with stoichiometric balance, sorption mechanism of Sr on TiNT was found to be ion-exchange between Na in TiNT lattice and Sr in solution phase, which was also confirmed by XRD and Raman analysis. Among competitive ions, Ca

  1. Regional and interspecific variation in Sr, Ca, and Sr/Ca ratios in avian eggshells from the USA.

    Science.gov (United States)

    Mora, Miguel A; Brattin, Bryan; Baxter, Catherine; Rivers, James W

    2011-08-01

    To examine regional variation in strontium (Sr), which at high concentrations may reduce eggshell quality, increase egg breakage and reproductive failure, we analyzed Sr, and calcium (Ca) concentrations and Sr/Ca ratios in eggshells from 20 avian species from California, Texas, Idaho, Kansas, and Michigan. In addition, we included data previously reported from Arizona to expand the regional comparisons and to better establish patterns of Sr, and Sr/Ca ratios in bird species across the United States. We found Sr concentrations varied significantly among regions, among species, and among foraging guilds; this variability is strongly influenced by the Sr/Ca ratios in surface water from locations close to the region where the eggshells were collected. Sr concentrations and Sr/Ca ratios were significantly higher in bird eggshells from the Volta wildlife region in the San Joaquin Valley, California and in various locales from Arizona. Sr concentrations and Sr/Ca ratios in bird eggshells from other locations in the USA were lower than those detected in these two regions. Among foraging guilds, invertivores had the highest Sr concentrations and Sr/Ca ratios and carnivores had the lowest. In general, the Sr/Ca ratio increased strongly with increasing Sr concentrations (R(2) = 0.99, P eggshells suggesting that these values could be determined from Sr/Ca ratios in water. Eggshell thickness was poorly correlated with Sr (R(2) = 0.03) but had a significant and positive correlation with Ca and was more properly correlated by a quadratic equation (R(2) = 0.50, Thickness = 2.13 - 0.02Ca - 3.07 * 10(-5)Ca(2)). Our study provides further evidence that Sr accumulates significantly in the avian eggshell, in some regions at concentrations which could be of concern for potential negative effects on reproduction. We suggest that when assessing the effects of metals on avian reproduction in regions with high Sr deposits in rock and soil, Sr concentrations in the eggshell also should be

  2. Renewal characterization of Markov modulated Poisson processes

    Directory of Open Access Journals (Sweden)

    Marcel F. Neuts

    1989-01-01

    Full Text Available A Markov Modulated Poisson Process (MMPP M(t defined on a Markov chain J(t is a pure jump process where jumps of M(t occur according to a Poisson process with intensity λi whenever the Markov chain J(t is in state i. M(t is called strongly renewal (SR if M(t is a renewal process for an arbitrary initial probability vector of J(t with full support on P={i:λi>0}. M(t is called weakly renewal (WR if there exists an initial probability vector of J(t such that the resulting MMPP is a renewal process. The purpose of this paper is to develop general characterization theorems for the class SR and some sufficiency theorems for the class WR in terms of the first passage times of the bivariate Markov chain [J(t,M(t]. Relevance to the lumpability of J(t is also studied.

  3. Effect of SrO content on Zeolite Structure

    Science.gov (United States)

    Widiarti, N.; Sari, U. S.; Mahatmanti, F. W.; Harjito; Kurniawan, C.; Prasetyoko, D.; Suprapto

    2018-04-01

    The aims of current studies is to investigate the effect of strontium oxide content (SrO) on synthesized zeolite. Zeolite was synthesized from Tetraethyl orthosilicate (TEOS) as precursors of SiO2 and aluminum isopropoxide (AIP) precursors. The mixture was aged for 3 days and hydrothermally treated for 6 days. The SrO content was added by impregnation method. The products were then characterized using X-Ray Diffraction (XRD), Fourier Transform Infrared (FTIR), and Surface Area Analyzer (SAA). The diffractogram confirmed the formation of Faujasite-like zeolite. However, after the addition of SrO, the crystallinity of zeolite was deformed. The diffractograms shows the amorphous phase of zeolite were decrease as the SrO content is increase. The structural changes was also observed from FTIR spectra which shows the shifting and peak formation. The surface area analysis showed that the increasing loading of SrO/Zeolites reduced the catalyst surface area.

  4. Fusion fuel and renewables

    International Nuclear Information System (INIS)

    Entler, Slavomir

    2015-01-01

    It is shown that fusion fuel meets all aspects applied when defining renewables. A table of definitions of renewables is presented. The sections of the paper are as follows: An industrial renewable source; Nuclear fusion; Current situation in research; Definitions of renewable sources; Energy concept of nuclear fusion; Fusion fuel; Natural energy flow; Environmental impacts; Fusion fuel assessment; Sustainable power; and Energy mix from renewables. (P.A.)

  5. The surface evolution of La0.4Sr0.6TiO3+δ anode in solid oxide fuel cells: Understanding the sulfur-promotion effect

    Science.gov (United States)

    Yan, Ning; Zanna, Sandrine; Klein, Lorena H.; Roushanafshar, Milad; Amirkhiz, Babak S.; Zeng, Yimin; Rothenberg, Gadi; Marcus, Philippe; Luo, Jing-Li

    2017-03-01

    The ideal solid oxide fuel cells (SOFCs) can be powered by readily available hydrocarbon fuels containing impurities. While this is commonly recognized as a key advantage of SOFC, it also, together with the elevated operating temperature, becomes the main barrier impeding the in-situ or operando investigations of the anode surface chemistry. Here, using a well-designed quenching experiment, we managed to characterize the near-surface structure of La0.4Sr0.6TiO3+δ (LST) anode in SOFCs fuelled by H2S-containing methane. This new method enabled us to clearly observe the surface amorphization and sulfidation of LST under simulated SOFC operating conditions. The ∼1 nm-thick two dimensional sulfur-adsorbed layer was on top of the disordered LST, containing -S, -SH and elemental sulfur species. In SOFC test, such "poisoned" anode showed increased performances: a ten-fold enhanced power density enhancement (up to 30 mW cm-2) and an improved open circuit voltage (from 0.69 V to 1.17 V). Moreover, its anodic polarization resistance in methane decreased to 21.53 Ω cm2, a difference of 95% compared with the sulfur-free anode. Control experiments confirmed that once the adsorbed sulfur species were removed electrochemically, methane conversion slowed down simultaneously till full stop.

  6. Comparison of the Sr isotopic signatures in brines of the Canadian and Fennoscandian shields

    International Nuclear Information System (INIS)

    Negrel, Philippe; Casanova, Joel

    2005-01-01

    A synthesis of Sr isotope data from shallow and deep groundwaters, and brines from the Fennoscandian and Canadian Shields is presented. A salinity gradient is evident in the water with concentrations varying from approximately 1-75 g L -1 below 1500 m depth in the Fennoscandian Shield and from 10 up to 300 g L -1 below 650 m depth in the Canadian Shield. Strontium isotope ratios were measured to assess the origin of the salinity and evaluate the degree of water-rock interaction in the systems. In both shields, the Sr concentrations are enriched relative to Cl, defining a positive trend parallel to the seawater dilution line and indicative of Sr addition through weathering processes. The depth distribution for Sr concentration increases strongly with increasing depth in both shields although the variation in Sr-isotope composition does not mirror that of Sr concentrations. Strontium-isotope compositions are presented for surface waters, and groundwaters in several sites in the Fennoscandian and Canadian Shields. Numerous mixing lines can be drawn reflecting water-rock interaction. A series of calculated lines links the surface end-members (surface water and shallow groundwater) and the deep brines; these mixing lines define a range of 87 Sr/ 86 Sr ratios for the deep brines in different selected sites. All sites show a specific 87 Sr/ 86 Sr signature and the occurrence of large 87 Sr/ 86 Sr variations is site specific in both shields. In Canadian Shield brines, the Sr isotope ratios clearly highlight large water rock interaction that increases the 87 Sr/ 86 Sr ratio from water that could have been of marine origin. In contrast to the Canadian Shield, groundwater does not occur in closed pockets in the Fennoscandian, and the well-constrained 87 Sr/ 86 Sr signatures in deep brines should correspond to a large, well-mixed and homogeneous water reservoir, whose Sr isotope signature results from water-rock interaction

  7. Effect of Flowing Water on Sr Sorption Changes of Hydrous Sodium Titanate

    Directory of Open Access Journals (Sweden)

    Youko Takahatake

    2017-12-01

    Full Text Available Radioactive contaminated water has been generated at the Fukushima Daiichi Nuclear Power station (F1NPS. Hydrous sodium titanate (SrTreat® is able to remove radioactive Strontium (Sr from this water. Knowing the amount of radioactive nuclides in the used as-received SrTreat® is important for effective disposal and deposition of the F1NPS waste. This study investigated changes in the ability of SrTreat® to sorb Sr, and to understand the causes of changes in the sorbing. An investigation of the Sr sorption ability of SrTreat® is important for calculating the initial radioactive inventory of used SrTreat®. This study carries out Sr sorption studies with acid-base titrations and X-ray photoelectron spectroscopy (XPS to characterize the properties. After exposure to simulated treated water for 99 h, the surface structure of the SrTreat® was changed, and the percentage of sorbed Sr and the buffer capacity for protons decreased. When the amount of radioactive nuclides contained in the used SrTreat® is calculated from the sorption data of the as-received SrTreat®, the radioactive Sr content will be overestimated with a concomitant increase in the deposition and disposal costs of the used SrTreat®.

  8. Surface analysis monitoring of polyelectrolyte deposition on Ba0.5Sr0.5TiO3 thin films

    International Nuclear Information System (INIS)

    Morales-Cruz, Angel L.; Fachini, Estevao R.; Miranda, Felix A.; Cabrera, Carlos R.

    2007-01-01

    Thin films are currently gaining interest in many areas such as integrated optics, sensors, friction, reducing coatings, surface orientation layers, and general industrial applications. Recently, molecular self-assembling techniques have been applied for thin film deposition of electrically conducting polymers, conjugated polymers for light-emitting devices, nanoparticles, and noncentrosymmetric-ordered second order nonlinear optical (NOL) devices. Polyelectrolytes self-assemblies have been used to prepare thin films. The alternate immersion of a charged surface in polyannion and a polycation solution leads usually to the formation of films known as polyelectrolyte multilayers. These polyanion and polycation structures are not neutral. However, charge compensation appears on the surface. This constitutes the building driving force of the polyelectrolyte multilayer films. The present approach consists of two parts: (a) the chemisorption of 11-mercaptoundecylamine (MUA) to construct a self-assembled monolayer with the consequent protonation of the amine, and (b) the deposition of opposite charged polyelectrolytes in a sandwich fashion. The approach has the advantage that ionic attraction between opposite charges is the driving force for the multilayer buildup. For our purposes, the multilayer of polyelectrolytes depends on the quality of the surface needed for the application. In many cases, this approach will be used in a way that the roughness factor defects will be diminished. The polyelectrolytes selected for the study were: polystyrene sulfonate sodium salt (PSS), poly vinylsulfate potassium salt (PVS), and polyallylamine hydrochloride (PAH), as shown in . The deposition of polyelectrolytes was carried out by a dipping procedure with the corresponding polyelectrolyte. Monitoring of the alternate deposition of polyelectrolyte bilayers was done by surface analysis techniques such as X-ray photoelectron spectroscopy (XPS), specular reflectance infrared (IR), and

  9. Renewable target in sight

    International Nuclear Information System (INIS)

    Anon

    2000-01-01

    Australia's renewable energy industry is expecting several billion dollars of investment over the next 10 years following passage in December last year of the Renewable Energy Electricity) Act 2000 through Federal Parliament. The Act requires an additional 9500GWh of Australia's electricity production to be sourced from renewables by the year 2010. It also establishes a market for the 'green' component of the energy separate from the electricity itself, through a Renewable Energy Certificate (REC), whereby an accredited generator of renewable energy is able to issue one REC for each megawatt-hour of renewable energy generated

  10. Renewable energy annual 1996

    International Nuclear Information System (INIS)

    1997-03-01

    This report presents summary data on renewable energy consumption, the status of each of the primary renewable technologies, a profile of each of the associated industries, an analysis of topical issues related to renewable energy, and information on renewable energy projects worldwide. It is the second in a series of annual reports on renewable energy. The renewable energy resources included in the report are biomass (wood and ethanol); municipal solid waste, including waste-to-energy and landfill gas; geothermal; wind; and solar energy, including solar thermal and photovoltaic. The report also includes various appendices and a glossary

  11. Renewable energy annual 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This report presents summary data on renewable energy consumption, the status of each of the primary renewable technologies, a profile of each of the associated industries, an analysis of topical issues related to renewable energy, and information on renewable energy projects worldwide. It is the second in a series of annual reports on renewable energy. The renewable energy resources included in the report are biomass (wood and ethanol); municipal solid waste, including waste-to-energy and landfill gas; geothermal; wind; and solar energy, including solar thermal and photovoltaic. The report also includes various appendices and a glossary.

  12. LT-STM/STS observation of definite superconducting gap states on the multistage crystal surface of Bi2Sr2CaCu2O8+x

    International Nuclear Information System (INIS)

    Murakami, Hironaru; Aoki, Ryozo

    1996-01-01

    Low temperature STM/STS observations have been carried out on cleaved BSCCO crystal surfaces. The authors have succeeded in detection of a special layer, probably a CuO 2 or Ca layer exposed on the surface. The STS spectrum which was reproducibly observed on this special site shows a considerably anisotropic but distinct superconducting gap structure with a definite and flat gap bottom region. This gap structure shows significantly different characteristic from another gap structure observed on the BiO layer, which shows a rounded shape at the gap bottom region without any indication of a finite gap state

  13. The "AQUASCOPE" simplified model for predicting 89, 90Sr, 131l and 134, 137Cs in surface waters after a large-scale radioactive fallout

    NARCIS (Netherlands)

    Smith, J.T.; Belova, N.V.; Bulgakov, A.A.; Comans, R.N.J.; Konoplev, A.V.; Kudelsky, A.V.; Madruga, M.J.; Voitsekhovitch, O.V.; Zibolt, G.

    2005-01-01

    Simplified dynamic models have been developed for predicting the concentrations of radiocesium, radiostrontium, and 131I in surface waters and freshwater fish following a large-scale radioactive fallout. The models are intended to give averaged estimates for radionuclides in water bodies and in fish

  14. Real-time {sup 90}Sr Counter

    Energy Technology Data Exchange (ETDEWEB)

    Kaneko, Naomi; Kawai, Hideyuki; Kodama, Satoshi; Kobayashi, Atsushi; Tabata, Makoto; Ito, Hiroshi [Graduate School of Science, Chiba University, Chiba, (Japan); Han, Soorim [Graduate School of Science, Chiba University, Chiba, (Japan); National Institute of Radiological Science, Chiba, (Japan)

    2015-07-01

    Radioisotopes have been emitted around Japan due to a nuclear accident at the Fukushima Daiichi nuclear power station in March 2011. A problem is the contaminated water including the atomic nucleus which relatively has a long half- life time and soluble such as {sup 90}Sr, {sup 137}Cs. Internal exposures by {sup 90}Sr are more dangerous than {sup 137}Cs's because Sr has effective half-life time of 18 years and property of accumulation in a born. We have developed real-time {sup 90}Sr counter which is sensitive beta-ray of maximum kinematic energy of 2.28 MeV from {sup 90}Sr and insensitive of beta-ray of maximum kinematic energy of 1.17 MeV and gamma-ray from {sup 90}Sr by Cherenkov detection. This counter composes of Cerenkov counter, trigger scintillation counter and veto counter. Silica aerogel for Cherenkov counter can obtain refractive index between 1.017 and 1.049 easily. And wavelength shifting fiber (WLSF) is used as a light guide for extending effective area and producing lower cost. A mechanism of the identification of {sup 90}Sr is explained in following. In case of {sup 90}Sr, when the trigger counter reacts on the beta-ray from {sup 90}Sr, aerogel emits the Cherenkov light and WLSF reacts and read the Cherenkov light. On the other hand, in case of {sup 137}Cs, the trigger counter reacts on the beta-ray, aerogel stops the beta- ray and Cherenkov light is not emitted. Therefore, aerogel has a function as a radiator and shielding material. the gamma-ray is not reacted on the lower density detector. Cosmic rays would be also reacted by the veto counter. A prototype counter whose the effective area is 30 cm x 10 cm was obtained (2.0±1.2){sup 3} of mis-identification as {sup 137}Cs/{sup 90}Sr. Detection limit in the surface contamination inspection depends on measurement time and effective area mainly. The sensitivity of wide range, 10{sup -2} - 10{sup 4} Bq/cm{sup 2}, is obtained by adjustment of detection level in circuit of this counter. A lower

  15. Renewable Energy Certificates (RECs)

    Science.gov (United States)

    Renewable Energy Certificates (RECs), are tradable, non-tangible energy commodities in the United States that represent proof that 1 megawatt-hour (MWh) of electricity was generated from an eligible renewable energy resource.

  16. Online driver's license renewal.

    Science.gov (United States)

    2015-09-01

    The Kentucky Department of Vehicle Regulation is exploring the possibility of developing and implementing online : drivers license renewal. The objective of this project was to: 1) evaluate online drivers license and REAL ID renewal : programs ...

  17. Resilient Renewable Energy Microgrids

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, Katherine H [National Renewable Energy Laboratory (NREL), Golden, CO (United States); DiOrio, Nicholas A [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Butt, Robert S [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Cutler, Dylan S [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Richards, Allison [Unaffiliated

    2017-11-14

    This presentation for the Cable-Tec Expo 2017 offers information about how renewable microgrids can be used to increase resiliency. It includes information about why renewable energy battery diesel hybrids microgrids should be considered for backup power, how to estimate economic savings of microgrids, quantifying the resiliency gain of microgrids, and where renewable microgrids will be successful.

  18. Kinetics and Mechanisms of Oxygen Surface Exchange on La0.6Sr0.4FeO3-delta Thin Films

    DEFF Research Database (Denmark)

    Mosleh, Majid; Søgaard, Martin; Hendriksen, Peter Vang

    2009-01-01

    and oxygen partial pressure [i.e., the incorporation reaction has the same reaction enthalpy (H0=−105 KJ/mol) and entropy (S0=−75.5 J/mol/K) as found for bulk material]. The thin film shows smaller apparent electrical conductivity than reported for bulk. This is due to imperfections in the film, which...... is not totally dense and contains closed porosity. Electrical conductivity relaxation was used to determine the surface exchange coefficient and its dependence on the temperature and oxygen partial pressure. Relaxation curves showed a good fit to a simple exponential decay. The vacancy surface exchange...... coefficient (kV) determined from Kchem shows a slope (log kV vs log PO2) between 0.51 and 0.85. It is further found that kV is proportional to the product of the oxygen partial pressure and the vacancy concentration (kVPO2). Different reaction mechanisms that can account for the observed PO2 and -dependence...

  19. Mapping of renewable energies

    International Nuclear Information System (INIS)

    Boulanger, V.

    2013-01-01

    Germany is the champion of green energy in Europe: the contribution of renewable energies to electricity generation reached about 20% in 2011. This article describes the situation of renewable energies in Germany in 2011 with the help of 2 maps, the first one gives the installed electrical generation capacity for each region and for each renewable energy source (wind power, hydro-electricity, biomass, photovoltaic energy and biogas) and the second one details the total number of jobs (direct and indirect) for each renewable energy source and for each region. In 2011 about 372000 people worked in the renewable energy sector in Germany. (A.C.)

  20. Peculiarities of Sr-90 migration in the environment

    International Nuclear Information System (INIS)

    Romanov, G.N.; Stukin, D.A.; Aleksakhin, R.M.

    1991-01-01

    The Eastern Urals radioactive track which formed as a result of the Kyshtym accident constituted a natural experimental base for studying the dynamics of Sr-90 behaviour and migration in the environment. Sr-90 behaviour in soil depends on the processes involved in its physical migration horizontally (water runoff, wind transport) and vertically (effective diffusion), on the intensity with which the physico-chemical forms of strontium change, and primarily on Sr-90 incorporation into the soil-absorptive complex. Over 30 years the effective diffusion processes led to downward displacement of Sr-90 in undisturbed soil to a depth of 30 to 50 cm. In 1988 84-94% of the Sr-90 was located in the 10 cm layer as against 90% in the 2 cm layer in the initial 1 or 2 years. The amount of Sr-90 in mobile forms in leached chernozem and grey forest soil hardly changed over time, amounting to between 76 and 90%. In the first 5-10 years Sr-90 surface water runoff was about 0.2% (and Sr-90 wind resuspension 0.1-1.0%) per year of the Sr-90 inventory per unit area. Due to Sr-90 loss from the top soil layer the water runoff and wind resuspension processes decreased exponentially, halving every 4 to 5 years. In most cases, Sr-90 transfer from soil to plants via the roots does not involve discrimination of Sr-90 with regard to calcium, and therefore the Sr-90 accumulation level in various species of natural and agricultural plants depends on their calcium requirements and the amount of exchangeable calcium in the soil. This made it possible to work out quantitative indices for forecasting Sr-90 accumulation in various species of plants for given types of soil. As Sr-90 moves through the trophic chains (including the agricultural one) we find - depending on whether two adjoining links discriminate against it or not as regards calcium - that some organisms reject it while others concentrate it. When restoring farming on the contaminated territory the fact that cattle discriminated against Sr

  1. Renewable energy annual 1995

    International Nuclear Information System (INIS)

    1995-12-01

    The Renewable Energy Annual 1995 is the first in an expected series of annual reports the Energy Information Administration (EIA) intends to publish to provide a comprehensive assessment of renewable energy. This report presents the following information on the history, status, and prospects of renewable energy data: estimates of renewable resources; characterizations of renewable energy technologies; descriptions of industry infrastructures for individual technologies; evaluations of current market status; and assessments of near-term prospects for market growth. An international section is included, as well as two feature articles that discuss issues of importance for renewable energy as a whole. The report also contains a number of technical appendices and a glossary. The renewable energy sources included are biomass (wood), municipal solid waste, biomass-derived liquid fuels, geothermal, wind, and solar and photovoltaic

  2. Renewable energy annual 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-01

    The Renewable Energy Annual 1995 is the first in an expected series of annual reports the Energy Information Administration (EIA) intends to publish to provide a comprehensive assessment of renewable energy. This report presents the following information on the history, status, and prospects of renewable energy data: estimates of renewable resources; characterizations of renewable energy technologies; descriptions of industry infrastructures for individual technologies; evaluations of current market status; and assessments of near-term prospects for market growth. An international section is included, as well as two feature articles that discuss issues of importance for renewable energy as a whole. The report also contains a number of technical appendices and a glossary. The renewable energy sources included are biomass (wood), municipal solid waste, biomass-derived liquid fuels, geothermal, wind, and solar and photovoltaic.

  3. Renewable Energy: Policy Considerations for Deploying Renewables

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-07-01

    This information paper accompanies the IEA publication Deploying Renewables 2011: Best and Future Policy Practice (IEA, 2011a). It provides more detailed data and analysis on policies for Deploying Renewables, and is intended to complement the main publication. It provides an account of the strategic drivers underpinning renewable energy (RE) technology deployment (energy security, economic development and environment protection) and assesses RE technologies with respect to these drivers, including an estimate of GHG emissions reductions due to RE technologies. The paper also explores the different barriers to deploying renewables at a given stage of market maturity and discusses what tools policy makers can avail of to succeed in removing deployment barriers. An additional topical highlight explores the challenges associated with accelerating the diffusion of RE technologies in developing countries.

  4. VT Renewable Energy Sites - Renewable Energy Professionals

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The Renewable Energy Atlas of Vermont and this dataset were created to assist town energy committees, the Clean Energy Development Fund and other...

  5. Preparation of Sr adsorptive fiber by impregnating with crown ether derivative for 90Sr measurement

    International Nuclear Information System (INIS)

    Horita, Takuma; Asai, Shiho; Hanzawa, Yukiko; Kitatsuji, Yoshihiro; Konda, Miki; Saito, Kyoichi; Fujiwara, Kunio; Sugo, Takanobu

    2017-01-01

    A Sr adsorption fiber was prepared for rapid analysis of 90 Sr content in the fiber using radiation-induced emulsion graft polymerization and subsequent chemical modification. A polyethylene fiber with a diameter of 13 μm was first immersed in a methanol solution of an epoxy-group-containing vinyl monomer, glycidyl methacrylate (GMA), and polyoxyethylene sorbitol ester (Tween20) as a surfactant for the graft-polymerization of GMA. Octadecylamine was then bound to a polymer chain extending from the fiber surface, providing hydrophobicity to the polymer chain. Dicyclohexano-18-crown-6 (DCH18C6) was finally impregnated onto the polymer chain via a hydrophobic interaction between the octadecyl moiety of the polymer chain and the cyclohexyl moiety of DCH18C6. The fiber surface structure, characterized by DCH18C6 molecules loosely entangled with polymer chains, allowed for the rapid adsorption of Sr ions at an adsorption rate of approximately 100-times higher than that of a commercially available Sr-selective resin (Sr Resin ® ). (author)

  6. In-Situ Catalytic Surface Modification of Micro-Structured La0.6Sr0.4Co0.2Fe0.8O3-δ (LSCF Oxygen Permeable Membrane Using Vacuum-Assisted technique

    Directory of Open Access Journals (Sweden)

    Othman Nur Hidayati

    2016-01-01

    Full Text Available This paper aims at investigating the means to carry out in-situ surface modification of La0.6Sr0.4Co0.2Fe0.8O3-δ (LSCF oxygen permeable membrane by using vacuum assisted technique. The unique structure of the LSCF hollow fibre membrane used in this study, which consists of an outer dense oxygen separation layer and conical-shaped microchannels open at the inner surface has allowed the membrane to be used as oxygen separation membrane and as a structured substrate for where catalyst can be deposited. A catalyst solution of similar material, LSCF was prepared using sol-gel technique. Effects of calcination temperature and heating rate were investigated using XRD and TGA to ensure pure perovskites structure of LSCF was obtained. It was found that a lower calcination temperature can be used to obtain pure perovskite phase if slower heating rate is used. The SEM photograph shows that the distribution of catalyst onto the membrane microchannels using in-situ deposition technique was strongly related to the viscosity of LSCF catalytic sol. Interestingly, it was found that the amount of catalyst deposited using viscous solution was slightly higher than the less viscous sol. This might be due to the difficulty of catalyst sol to infiltrate the membrane and as a result, thicker catalyst layer was observed at the lumen rather than onto the conical-shaped microchannels. Therefore, the viscosity of catalyst solution and calcination process should be precisely controlled to ensure homogeneous catalyst layer deposition. Analysis of the elemental composition will be studied in the future using energy dispersive X-ray Spectroscopy (EDX to determine the elements deposited onto the membranes. Once the elemental analysis is confirmed, oxygen permeation analysis will be carried out.

  7. Review of SR 97

    International Nuclear Information System (INIS)

    Voss, C.I.

    2000-01-01

    The safety analysis conducted by SKB for SR 97 is impressive in terms of both scale and content. In addition to an eventual solution to Sweden's nuclear waste isolation question, much general scientific knowledge of real value in other applications will be created as a by-product of SKB's efforts. This review focuses on those geoscience aspects of SR 97 that have the most important effects on radionuclide release from each barrier. Indeed, SR 97 elucidates the most important geoscience parameters that control releases from the near field and the far field; these comprise mainly the transport resistance parameter, and the sorption coefficients for each nuclide, the matrix diffusion coefficient, and the Darcy flux. The Main Report is the most important document in SR 97 inasmuch as it is the only one that brings together all of the supporting work to answer the question of safety. Unfortunately pervading the good supporting work done is the impression that the Main Report is not balanced, that it emphasizes optimistic aspects and downplays the negative. SKB specifies 3 main requirements to guarantee proper repository function: a non-oxidizing subsurface environment, temperatures less than 100 C, and a mechanically stable low-permeability buffer surrounding the canisters. The first and third requirements are not thoroughly proven by SKB. One source of near-field doubt stems from the consequences of combinations of scenarios in which several negative events are linked, while the effect of each scenario is mainly evaluated only independently in SR 97. More pertinently, disastrous breakdown of complex systems may occur due to a chain of linked failures. For example, in the glacial scenario: high ground-water flow (possible ablation of buffer and high fluid transport), change in ground-water chemistry (even the possibility of oxidizing conditions), new flow paths, significant changes in mechanical stress and possible motion along faults (which may also generate new flow

  8. Renewable Substitutability Index: Maximizing Renewable Resource Use in Buildings

    OpenAIRE

    Srinivasan, Ravi; Campbell, Daniel; Wang, Wei

    2015-01-01

    In order to achieve a material and energy balance in buildings that is sustainable in the long run, there is an urgent need to assess the renewable and non-renewable resources used in the manufacturing process and to progressively replace non-renewable resources with renewables. Such progressive disinvestment in the non-renewable resources that may be substituted with renewable resources is referred to as “Renewable Substitutability” and if implemented, this process will lead to a paradigm sh...

  9. Laser ablation inductively coupled plasma mass spectrometry. An alternative technique for monitoring 90Sr

    International Nuclear Information System (INIS)

    TsingHai Wang; Yan-Chen Lai; Yi-Kong Hsieh; Chu-Fang Wang

    2017-01-01

    Developing a rapid detection method for monitoring released 90 Sr remains a challenge to analytical chemists, particularly considering its low concentration and significant interferences in environmental samples. We proposed a concept as an alternative to detect 90 Sr on the surface of fish scales using laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS). The high affinity of fish scales to Sr is capable of preconcentrating 90 Sr that minimizes isobaric interferences from 90 Zr + or 89 YH + , while tailing effect by abundant 88 Sr can be effectively reduced by adjusting the forward power of ICP-MS component. Adopting dried droplets of internal standards further allows a semiquantification of 90 Sr content on the surface of fish scales, which also arises an opportunity to monitoring the bioaccumulation of 90 Sr after Fukushima Daiichi nuclear disaster. (author)

  10. Policies for Renewable Heat

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-07-01

    This paper builds on IEA publications, Deploying Renewables, Principles for Effective Policies and Deploying Renewables, Best and Future Policy Practice, that discuss the 'integrated policy approach,' whereby renewable energy technologies require different support policies at different stages of their maturity pathways. The paper discusses how the integrated policy approach applies to renewable heat. It attempts to provide guidance for policy-makers on renewable heat throughout the different phases of the policy lifecycle, allowing for the specific challenges of renewable heat and needs of the many stakeholders involved. Stimulating a market for heat involves challenges that are different and, often, more difficult to overcome than in the electricity and transport sectors.

  11. Decay of 83Sr

    International Nuclear Information System (INIS)

    Yu Xiaohan; Shi Shuanghui; Gu Jiahui

    1997-01-01

    The decay of 83 Sr was reinvestigated using γ singles and γ-γ-t coincidence measurement. A new level scheme of Rb, which contains 41 excited levels and about 180 transitions, is constructed. 19 new levels were added to the old level scheme and 8 formerly adopted levels were denied. A new data set of branching ratio, log(ft) value and spin parity was obtained

  12. China's renewables law

    International Nuclear Information System (INIS)

    Zhu Li

    2005-01-01

    The paper discusses China's Renewable Energy Promotion Law which will come into force in January 2006. The law shows China's commitment to renewable energy sources. The target is to raise the country's energy consumption from renewables to 10% by 2020. Data for current capacity, and expected capacity by 2020, are given for wind power, solar power, biomass and hydroelectric power. The financial and technological hurdles which China must overcome are mentioned briefly

  13. Applicability of 87Sr/86Sr in examining return flow of irrigation water in highly agricultural watersheds in Japan

    Science.gov (United States)

    Yoshida, T.; Nakano, T.; Shin, K. C.; Tsuchihara, T.; Miyazu, S.; Kubota, T.

    2017-12-01

    Water flows in watersheds containing extensive areas of irrigated paddies are complex because of the substantial volumes involved and the repeated cycles of water diversion from, and return to, streams. For better management of low-flow conditions, numerous studies have attempted to quantify the return flow using the stable isotopes of water; however, the temporal variation in these isotopic compositions due to fractionation during evaporation from water surfaces hinders their application to watersheds with extensive irrigated paddies. In this study, we tested the applicability of the strontium isotopes (87Sr/86Sr, hereafter Sr ratio) for studying hydrological processes in a typical agricultural watershed located on the alluvial fan of the Kinu River, namely the Gogyo River, in central Japan. The Sr ratio of water changes only because of interactions with the porous media it flows through, or because of mixing with water that has different Sr ratios. We sampled water both at a single rice paddy, and on the watershed scale in the irrigated and non-irrigated periods. The soil water under the paddy decreased as sampling depth increased, and the soil water at a depth of 1.5 m showed a similar Sr ratio to the spring. The water sampled in the drainage channel with a concrete lined bottom showed a similar Sr ratio to the irrigation water, whereas that with a soil bottom was plotted between the plots of the irrigation water and shallow aquifer. These results suggest the Sr ratio decreases as it mixes with the soil water through percolation; whereas the Sr ratio will be less likely to change when water drains from paddies via surface pathways. The streamflow samples were plotted linearly on the Sr ratio and 1/Sr plot, indicating that the streamflow was composed of two end-members; the irrigation water and the shallow aquifer. The continuous decline in the Sr ratio along the stream suggests an exfiltration of water from the shallow aquifers. The stream water during the non

  14. Renewable energy resources

    CERN Document Server

    Twidell, John

    2015-01-01

    Renewable Energy Resources is a numerate and quantitative text covering the full range of renewable energy technologies and their implementation worldwide. Energy supplies from renewables (such as from biofuels, solar heat, photovoltaics, wind, hydro, wave, tidal, geothermal, and ocean-thermal) are essential components of every nation's energy strategy, not least because of concerns for the local and global environment, for energy security and for sustainability. Thus in the years between the first and this third edition, most renewable energy technologies have grown from fledgling impact to s

  15. The renewable chemicals industry

    DEFF Research Database (Denmark)

    Christensen, Claus H.; Rass-Hansen, J.; Marsden, Charlotte Clare

    2008-01-01

    per kilogram of desired product to illustrate in which processes the use of renewable resources lead to the most substantial reduction of CO2 emissions. The steps towards a renewable chemicals industry will most likely involve intimate integration of biocatalytic and conventional catalytic processes......The possibilities for establishing a renewable chemicals industry featuring renewable resources as the dominant feedstock rather than fossil resources are discussed in this Concept. Such use of biomass can potentially be interesting from both an economical and ecological perspective. Simple...

  16. Renewables. The clean advantage

    International Nuclear Information System (INIS)

    Klein, A.

    2006-01-01

    Europe's big utilities are increasingly seeing renewable energy as a viable alternative to conventional forms of power generation which at present have disadvantages in terms of cost and/or environment. Europe's biggest 20 utilities aim to double their renewables capacity in the next five years and nearly 20 billion US dollars have been earmarked for such projects. This report by Emerging Energy Research discusses the likely trends for the next five years. The various sources of renewable energy and how they might be developed are discussed. The companies leading exploitation of renewables and their market share are named

  17. SR-71 Pilot Stephen (Steve) D. Ishmael

    Science.gov (United States)

    1992-01-01

    sideslip, which are normally obtained with small tubes and vanes extending into the airstream. One of Dryden's SR-71s was used for the Linear Aerospike Rocket Engine, or LASRE Experiment. Another earlier project consisted of a series of flights using the SR-71 as a science camera platform for NASA's Jet Propulsion Laboratory in Pasadena, California. An upward-looking ultraviolet video camera placed in the SR-71's nosebay studied a variety of celestial objects in wavelengths that are blocked to ground-based astronomers. Earlier in its history, Dryden had a decade of past experience at sustained speeds above Mach 3. Two YF-12A aircraft and an SR-71 designated as a YF-12C were flown at the center between December 1969 and November 1979 in a joint NASA/USAF program to learn more about the capabilities and limitations of high-speed, high-altitude flight. The YF-12As were prototypes of a planned interceptor aircraft based on a design that later evolved into the SR-71 reconnaissance aircraft. Dave Lux was the NASA SR-71 project manger for much of the decade of the 1990s, followed by Steve Schmidt. Developed for the USAF as reconnaissance aircraft more than 30 years ago, SR-71s are still the world's fastest and highest-flying production aircraft. The aircraft can fly at speeds of more than 2,200 miles per hour (Mach 3+, or more than three times the speed of sound) and at altitudes of over 85,000 feet. The Lockheed Skunk Works (now Lockheed Martin) built the original SR-71 aircraft. Each aircraft is 107.4 feet long, has a wingspan of 55.6 feet, and is 18.5 feet high (from the ground to the top of the rudders, when parked). Gross takeoff weight is about 140,000 pounds, including a possible fuel weight of 80,280 pounds. The airframes are built almost entirely of titanium and titanium alloys to withstand heat generated by sustained Mach 3 flight. Aerodynamic control surfaces consist of all-moving vertical tail surfaces, ailerons on the outer wings, and elevators on the trailing edges

  18. Effects of packaging SrI{sub 2}(Eu) scintillator crystals

    Energy Technology Data Exchange (ETDEWEB)

    Sturm, Benjamin W., E-mail: sturm1@llnl.gov [Lawrence Livermore National Laboratory, Livermore, CA 94550 (United States); Cherepy, Nerine J.; Drury, Owen B.; Thelin, Peter A.; Fisher, Scott E.; Payne, Stephen A. [Lawrence Livermore National Laboratory, Livermore, CA 94550 (United States); Burger, Arnold [Fisk University, Nashville, TN 37201 (United States); Boatner, Lynn A.; Ramey, Joanne O. [Oak Ridge National Laboratory, Oak Ridge, TN 37830 (United States); Shah, Kanai S.; Hawrami, Rastgo [Radiation Monitoring Devices, Watertown, MA 02472 (United States)

    2011-10-01

    Recent renewed emphasis placed on gamma-ray detectors for national security purposes has motivated researchers to identify and develop new scintillator materials capable of high energy resolution and growable to large sizes. We have discovered that SrI{sub 2}(Eu) has many desirable properties for gamma-ray detection and spectroscopy, including high light yield of {approx}90,000 photons/MeV and excellent light yield proportionality. We have measured <2.7% FWHM at 662 keV with small detectors (<1 cm{sup 3}) in direct contact with a photomultiplier tube, and {approx}3% resolution at 662 keV is obtained for 1 in.{sup 3} crystals. Due to the hygroscopic nature of SrI{sub 2}(Eu), similar to NaI(Tl), proper packaging is required for field use. This work describes a systematic study performed to determine the key factors in the packaging process to optimize performance. These factors include proper polishing of the surface, the geometry of the crystal, reflector materials and windows. A technique based on use of a collimated {sup 137}Cs source was developed to examine light collection uniformity. Employing this technique, we found that when the crystal is packaged properly, the variation in the pulse height at 662 keV from events near the bottom of the crystal compared to those near the top of the crystal could be reduced to <1%. This paper describes the design and engineering of our detector package in order to improve energy resolution of 1 in.{sup 3}-scale SrI{sub 2}(Eu) crystals.

  19. Developing the use of renewable heat

    International Nuclear Information System (INIS)

    Nifenecker, Herve

    2013-01-01

    The author reports a study in which he shows that the heat production by means of renewable energies is an efficient method to reach the objective of 23 per cent of renewable energies in the French final energy consumption. He browses the different techniques of renewable heat production (solar heat, wood-fuel, surface geothermal) and indicates the associated potential resources. He proposes a cost analysis which compares the use of gas and electricity with three techniques of production of renewable heat: solar heat to produce hot water, biomass combustion (more particularly wood), solar heat extracted with fuel cells. He also assesses tariffs and CO 2 emissions. Then, he elaborates a strategy to phase out fossil energies: a modification of the RT 2012 thermal regulation, to give up the purchase obligation for electricity produced by wind and photovoltaic energy, to extend the CSPE calculation basis, to put oil-fuel and gas boilers out of the market, to support the development of renewable heat production, to improve the competitiveness of the different techniques of renewable heat production. He finally gives a brief overview of industrial perspectives created by such a development of renewable heat

  20. Marine Renewable Energies

    DEFF Research Database (Denmark)

    Azzellino, Arianna; Conley, Daniel; Vicinanza, Diego

    2013-01-01

    Countries with coastlines may have valuable renewable energy resources in the form of tides, currents, waves, and offshorewind.The potential to gather energy from the sea has recently gained interest in several nations, so Marine Renewable Energy Installations (hereinafter MREIs) will likely become...

  1. Renewable Resources in SA

    CSIR Research Space (South Africa)

    Mushwana, C

    2015-02-01

    Full Text Available Renewable energy is derived form natural resources that are replenished at a faster rate than they are consumed, and thus cannot be depleted. Solar, wind, geothermal, hydro, and some forms of biomass are common sources of renewable energy. Almost 90...

  2. Renewable Energy in Alaska

    Energy Technology Data Exchange (ETDEWEB)

    2013-03-01

    This report examines the opportunities, challenges, and costs associated with renewable energy implementation in Alaska and provides strategies that position Alaska's accumulating knowledge in renewable energy development for export to the rapidly growing energy/electric markets of the developing world.

  3. Renewable Energy Technology

    Science.gov (United States)

    Daugherty, Michael K.; Carter, Vinson R.

    2010-01-01

    In many ways the field of renewable energy technology is being introduced to a society that has little knowledge or background with anything beyond traditional exhaustible forms of energy and power. Dotson (2009) noted that the real challenge is to inform and educate the citizenry of the renewable energy potential through the development of…

  4. Renewable energy export network

    International Nuclear Information System (INIS)

    Anon

    2000-01-01

    A Renewable Energy Exporters Network (REEN) has recently been established, following a meeting of renewable energy exporters and government agencies on 30 October 2000. REEN will assist the Australian renewable energy industry to take advantage of the opportunities offered by the burgeoning global market for renewable energy goods and services. Recent estimates of the significant potential global growth is renewable energy demand have reinforced the industry and Government's view that, in the medium to long-term, growth in the Australian renewable energy industry will largely depend on capturing export market share. Expanding the export market was identified as a crucial component in the Renewable Energy Action Agenda, developed jointly by industry and Government and released in June 2000. It was estimated that, for the industry to achieve its vision of sales of $4 billion per year by 2010, exports would need to comprise approximately 50% of the forecast growth in sales. As such, the need for a specific export strategy for the Australian renewable energy industry was recognised in the Action Agenda, and the establishment of the REEN is one of the first initiatives undertaken as part of the Renewable Energy Export Strategy. The REEN comprises approximately 50 export-ready renewable energy companies, the Department of Industry, Science and Resources, Austrade, and Stage Government agencies such as NSW's Sustainable Energy Development Authority. The Export Network will operate electronically, with face-to-face meetings held as appropriate. The Department of Industry, Science and Resources will facilitate the Export Network and has published a website at www.isr.gov.au/industry/reen. The site includes: a members directory; a discussion forum; information on opportunities to showcase Australian renewable; energy products and services; and Iinks to sites containing information that may be useful to renewable energy exporters. Other actions that are being undertaken as

  5. Nuclear plant license renewal

    International Nuclear Information System (INIS)

    Gazda, P.A.; Bhatt, P.C.

    1991-01-01

    During the next 10 years, nuclear plant license renewal is expected to become a significant issue. Recent Electric Power Research Institute (EPRI) studies have shown license renewal to be technically and economically feasible. Filing an application for license renewal with the Nuclear Regulatory Commission (NRC) entails verifying that the systems, structures, and components essential for safety will continue to perform their safety functions throughout the license renewal period. This paper discusses the current proposed requirements for this verification and the current industry knowledge regarding age-related degradation of structures. Elements of a license renewal program incorporating NRC requirements and industry knowledge including a schedule are presented. Degradation mechanisms for structural components, their significance to nuclear plant structures, and industry-suggested age-related degradation management options are also reviewed

  6. New renewable energy sources

    International Nuclear Information System (INIS)

    2001-06-01

    This publication presents a review of the technological, economical and market status in the field of new renewable energy sources. It also deals briefly with the present use of energy, external conditions for new renewable energy sources and prospects for these energy sources in a future energy system. The renewable energy sources treated here are ''new'' in the sense that hydroelectric energy technology is excluded, being fully developed commercially. This publication updates a previous version, which was published in 1996. The main sections are: (1) Introduction, (2) Solar energy, (3) Bio energy, (4) Wind power, (5) Energy from the sea, (6) Hydrogen, (7) Other new renewable energy technologies and (8) New renewable s in the energy system of the future

  7. NRC's license renewal regulations

    International Nuclear Information System (INIS)

    Akstulewicz, Francis

    1991-01-01

    In order to provide for the continuity of the current generation of nuclear power plant operating licenses and at the same time ensure the health and safety of the public, and the quality of the environment, the US Nuclear Regulatory Commission (NRC) established a goal of developing and issuing regulations and regulatory guidance for license renewal in the early 1990s. This paper will discuss some of those activities underway to achieve this goal. More specifically, this paper will discuss the Commission's regulatory philosophy for license renewal and the two major license renewal rule makings currently underway. The first is the development of a new Part 54 to address procedural and technical requirements for license renewal; the second is a revision to existing Part 51 to exclude environmental issues and impacts from consideration during the license renewal process. (author)

  8. Renewable energy resources

    DEFF Research Database (Denmark)

    Ellabban, Omar S.; Abu-Rub, Haitham A.; Blaabjerg, Frede

    2014-01-01

    Electric energy security is essential, yet the high cost and limited sources of fossil fuels, in addition to the need to reduce greenhouse gasses emission, have made renewable resources attractive in world energy-based economies. The potential for renewable energy resources is enormous because...... they can, in principle, exponentially exceed the world's energy demand; therefore, these types of resources will have a significant share in the future global energy portfolio, much of which is now concentrating on advancing their pool of renewable energy resources. Accordingly, this paper presents how...... renewable energy resources are currently being used, scientific developments to improve their use, their future prospects, and their deployment. Additionally, the paper represents the impact of power electronics and smart grid technologies that can enable the proportionate share of renewable energy...

  9. Research of the value of linear distortion of renewable surface of part during rotary processing of bulky items without dismantling unit

    Science.gov (United States)

    Bondarenko, J. A.; Fedorenko, M. A.; Pogonin, A. A.

    2018-03-01

    The loading and unloading units and grinding mills of raw devices have internal cone type or pipe screw perceive load of incoming and outgoing material. The main part of the support assembly is a pin. Mounting seats for the pipe screws cone have traces of deformation and work hardening, while they themselves have wear of pins and deformation of the inner and outer cylindrical working surface. In the mill body, there are constantly acting dynamic forces causing vibration, which are transmitted to the stud and inner accelerating elements. Under the influence of stress and vibration, the housing spigot is in the stress-compressed state and stretched vertically and horizontally. As a result, the insertion element is deformed and weakened in the fixture. A moving element appears in the gap leading to the fact that it drops lfeedstock and under the influence of variable loads it is destroyed, as well as the seating surfaces of the insert pin member.

  10. Tradeoffs for Renewable Energy Projects: Environmental, Planning, and Mission Considerations

    Science.gov (United States)

    2010-04-01

    parabolic trough solar system for heating, cooling and hot water at Fort Huachuca, AZ from October 1979 (est.)  a solar pool heating system at Fort... collectors commercially applied Passive solar energy use Heat, cold, light, ventila- tion Demonstrations and applica- tions Artificial photosynthesis H2...the technologies that convert those energies into more usable forms is that renewable en- ERDC/CERL SR-10-2 36 ergy generally emits fewer compounds

  11. Case Studies on the Effectiveness of State Financial Incentives for Renewable Energy

    Energy Technology Data Exchange (ETDEWEB)

    None

    2002-09-01

    September 2002 · NREL/SR-620-32819 Case Studies on the Effectiveness of State Financial Incentives for Renewable Energy S. Gouchoe, V. Everette, and R. Haynes North Carolina State University Raleigh, North Carolina National Renewable Energy Laboratory 1617 Cole Boulevard Golden, Colorado 80401-3393 NREL is a U.S. Department of Energy Laboratory Operated by Midwest Research Institute · Battelle · Bechtel Contract No. DE-AC36-99-GO10337 September 2002 · NREL/SR-620-32819Case Studies on the Effecti

  12. Renewables in the Midwest

    International Nuclear Information System (INIS)

    Wager, J.S.

    1994-01-01

    Over the past three years, the Union of Concerned Scientists (UCS) has evaluated the potential for using renewable energy for electricity in the Midwest, and has been carrying out a multifaceted effort to expand the use of renewables in the region. The UCS study presents a strategy for developing renewable-electric technologies and resources in 12 midwestern states. UCS analysts used a geographic information system (GIS) to create data-bases of renewable resources, land uses, vegetation cover, terrain elevation and locations of utility transmission lines, and to analyze and present information on a .6 mi x .6 mi (1 km x 1 km) grid scale. In addition, UCS developed a model to calculate the net employment impact of renewable versus conventional electricity technologies on a state-by-state basis. In evaluating the costs and benefits of renewable energy sources, UCS analysts explored a cost assessment that accounted for the impact of pollution from fossil fuels on energy resource cost. Researchers also considered the risks associated with fuel-price volatility, environmental regulation, construction lead times and other uncertainties. Finally, UCS researchers suggested steps to remove the institutional, regulatory and legislative barriers that inhibit renewable energy development, and proposed policies to expand the use of the region's renewable resources. The UCS analysis showed that wind is currently the least expensive renewable resource. UCS also found numerous opportunities to expand biomass-electric generation in the near term, such as converting small coal-fired power plants to wood fuel, making greater use of logging residues and co-firing a small percentage of biomass with fossil fuel at large power plants

  13. Is the Modern Marine 87Sr/86Sr Cycle Balanced?

    Science.gov (United States)

    Peucker-Ehrenbrink, B.

    2017-12-01

    The marine 87Sr/86Sr record is one of the best-reconstructed isotope records with thousands of high quality measurements spanning the past 800 million years. It records a global signal of tectonic, biotic and climatic processes on Earth. Yet despite decades of research we still do not know whether the current marine Sr budget is in steady state. Studies of the marine 88Sr/86Sr record indicate that sources and sinks do not balance. The magnitude and isotope composition of the terrestrial inputs are being debated, and the magnitude and temporal variability of unradiogenic contributions are not well constrained. Here I provide a revised assessment of all continental sources of Sr to the ocean, including river runoff, submarine groundwater discharge (Beck et al., 2013), dissolution of riverine suspended matter in seawater and dissolution of volcanic ash deposited on the ocean (Jones et al., 2012). I contrast continental sources of Sr with estimates of marine sources of Sr to seawater, specifically high- and low-temperature submarine hydrothermal fluids, as well as diffusive diagenetic fluxes. Best current data imply that unradiogenic submarine hydrothermal inputs to seawater are insufficient to balance the flux of radiogenic continental Sr. The revised assessment of riverine contributions is based on Sr data for almost 230 rivers, an increasing amount of time-series data for such rivers, as well as river discharge and sediment flux data for more than 2000 rivers. Regional sampling biases have been corrected with the aid of digital bedrock maps, specifically along the western margin of North America, East Africa and the large drainage region of Arabia, India and SE Asia. Significant uncertainty in the chemical and isotopic compositions of runoff from Greenland and East Africa remains. The main uncertainty in the budget, however, is related to the possibility that modern rivers do not represent the pre-anthropogenic (natural) state of continental runoff (e.g. Ganges

  14. Damn renewable energies

    International Nuclear Information System (INIS)

    Gay, Michel

    2017-01-01

    In this book, the author describes how renewable energies have been developed in a way he considers as scandalous, whereas they are a technical, financial and ecological dead end. He also explains how ecologists (notably the ADEME) manipulate figures to make believe that these energies could be an answer to the needs of France, of Europe and of humanity. In a first chapter, he criticises the influence of a so-called green ideology on the design of energy transition. In the second one, he denounces twelve tales about energy transition. In the next chapters, he denounces the sham of renewable energies, and finally tells some unfortunate renewable experiments

  15. Renewable energies - Alain Chardon

    International Nuclear Information System (INIS)

    Anon.

    2012-01-01

    In an interview, the chairman of Cleantechs and Decarbonate, Capgemini Consulting, comments the challenge of the struggle against global warming, discusses the role of gas on the way towards a de-carbonated economy, the cost of renewable energies compared to that of fossil and nuclear energies. He outlines other brakes upon the development of renewable energies, discusses the political issues and the challenge of meeting European objectives with respect with the share of renewable energies in the energy mix and the electricity mix by 2020

  16. Renewable Energy Development in India

    Energy Technology Data Exchange (ETDEWEB)

    Gupta, K.M.

    2007-07-01

    India has done a significant progress in the power generation in the country. The installed generation capacity was 1300 megawatt (MW) at the time of Independence i.e. about 60 years back. The total generating capacity anticipated at the end of the Tenth Plan on 31-03-2007, is 1, 44,520 MW which includes the generation through various sectors like Hydro, Thermal and Nuclear. Emphasis is given to the renewable energy programme towards gradual commercialization. This programme is looked after by the Ministry of Non-Conventional Sources of energy. Since the availability of fossil fuel is on the decline therefore, in this backdrop the norms for conventional or renewable sources of energy (RSE) is given importance not only in India but has attracted the global attention. The main items under RSE are as follows: (i) Hydro Power (ii) Solar Power (iii) Wind Power (iv) Bio-mass Power (v) Energy from waste (vi) Ocean energy, and (vii) Alternative fuel for surface transportation. Evolution of power transformer technology in the country during the past five decades is quite impressive. There are manufacturers in the country with full access to the latest technology at the global level. Some of the manufacturers have impressive R&D set up to support the technology. Renewable energy is very much promoted by the Chinese Government. At the same time as the law was passed, the Chinese Government set a target for renewable energy to contribute 10% of the country's gross energy consumption by 2020, a huge increase from the current 1%. It has been felt that there is rising demand for energy, food and raw materials by a population of 2.5 billion Chinese and Indians. Both these countries have large coal dominated energy systems in the world and the use of fossil fuels such as coal and oil releases carbon dioxide (CO2) into the air which adds to the greenhouse gases which lead to global warming. (auth)

  17. The coprecipitation of Sr2+ with calcite at 250C and 1 atm

    International Nuclear Information System (INIS)

    Pingitore, N.E. Jr.; Eastman, M.P.

    1986-01-01

    The incorporation of Sr 2+ into calcite at earth surface aqueous conditions is affected by the absolute concentration of Sr 2+ , the presence of Ba 2+ and NaCl in the solution and the rate of precipitation. At solution ratios (molar) of Sr 2+ to Ca 2+ in the low 10 -3 range, which yield calcites with several hundred ppm Sr 2+ , kappasub(calcite) sup(Sr) typically assumes a value between 0.10 and 0.20. Above these concentrations the value of kappasub(calcite) sup(Sr) drops to approximately 0.06. Furthermore, if minor amounts of Ba 2+ or large amounts of Na + (0.48 M) are added to a dilute Sr 2+ solution, a value around 0.06 for kappasub(calcite)sup(Sr) is found. This 'strontium concentration effect' and the associated 'competitive cation effect' suggest that small amounts of Sr 2+ may be incorporated into a limited number of nonlattice sites in calcite. Incorporation of Sr 2+ into these sites, presumably defects, noticeably affects kappasub(calcite)sup(Sr) only at low Sr 2+ concentrations and in the absence of competition from other large cations. An increase in kappasub(calcite)sup(Sr) with rate of precipitation, qualitatively similar to that found in other studies, was observed only when precipitation times were decreased from days to hours. For many geologic settings a partition coefficient for Sr 2+ into calcite of 0.06 appears appropriate, but there are situations - very low Sr 2+ concentrations, the presence of Mg 2+ , and fast precipitation rates - in which a larger value might better approximate natural partitioning. (author)

  18. A study of cycling of 90Sr in a natural forest on the Canadian Shield

    International Nuclear Information System (INIS)

    Cooper, E.L.; Rahman, M.M.

    1994-01-01

    A study of the cycling of 90 Sr in a natural forest growing over a shallow zone of low-level 90 Sr-contaminated groundwater was carried out at the Chalk River Laboratories of AECL Research. The contamination is about 1 m below the surface under most of the site and evidence from earlier studies indicates that 90 Sr is being brought to the surface by deeper rooting trees. Once it is on the surface, the 90 Sr becomes available for uptake by other biota in the area. The study was initiated by taking an inventory of 90 Sr in various compartments including: soil, leaf litter, wood and foliage. Samples of leaf fall, stemflow and throughfall were also collected in order to estimate the relative importance of these mechanisms in cycling 90 Sr to the forest floor. Most of the 90 Sr on or near the surface is in the leaf litter and the top 8 cm of soil, as well as in the vegetation. Downward migration of 90 Sr through the unsaturated zone is slow. This may be due to strong retention by the soil; however, it could also be due to recycling of 90 Sr by the vegetation. The accumulated inventory in the leaf litter is about equal to the input from leaf fall over a period of 3 years

  19. Renewable energy in Taiwan

    International Nuclear Information System (INIS)

    Chen, Falin; Lu, Shyi-Min; Wang, Eric; Tseng, Kuo-Tung

    2010-01-01

    With limited indigenous conventional energy resources, Taiwan imports over 99% of its energy supply from foreign countries, mostly from the Middle East. Developing independent renewable energy resources is thus of priority concern for the Taiwanese government. A medium subtropical island surrounded by the Pacific Ocean, Taiwan has enormous potential to develop various renewable energies, such as solar energy, biomass energy, wind power, geothermal energy, hydropower, etc. However, owing to the importance of conventional fossil energy in generating exceptionally cheap electricity, renewable energy has not yet fully developed in Taiwan, resulting from a lack of market competition. Consequently, numerous promotional and subsidy programs have recently been proclaimed by the Taiwanese government, focused on the development of various renewables. This study reviews the achievements, polices and future plans in this area. (author)

  20. The value of renewables

    International Nuclear Information System (INIS)

    Koch, H.J.

    2001-01-01

    The article extols the virtues of renewable energy sources. Based largely on the outcome of an IAE meeting in May 2001, the author has outlined an approach for accelerating the development of renewables. The article quotes several statements made by the IAE with respect to the need for a secure supply of affordable energy, sustainable development, diversification, the value of renewables and challenges confronting developers of renewables. The article is presented under the sub-headings of: (i) harnessing energy market forces; (ii) understanding costs in the context of diversification; (iii) economic performance; (iv) environmental protection; (v) an IAE action plan and (vi) conclusions. The author was once the IAE's director for energy efficiency, technology and R and D

  1. Biotechnology for renewable chemicals

    DEFF Research Database (Denmark)

    Borodina, Irina; Kildegaard, Kanchana Rueksomtawin; Jensen, Niels Bjerg

    2014-01-01

    The majority of the industrial organic chemicals are derived from fossil sources. With the oil and gas resources becoming limiting, biotechnology offers a sustainable alternative for production ofchemicals from renewable feedstocks. Yeast is an attractive cell factory forsustainable production...

  2. Foundations for renewables

    Energy Technology Data Exchange (ETDEWEB)

    Neidlein, H.C. [German Agency Scherer Schnell Walser und Partner (Germany)

    2007-07-01

    In Germany, 77 foundations promote renewable energy technology with around Euro 25 million annually. The most important internationally active foundations, however, can be found in the Anglo-Saxon countries. (orig.)

  3. Renewable resources - future possibilities

    International Nuclear Information System (INIS)

    Thomas, Martin H.

    1998-01-01

    The paper describes the Australian Cooperative Research Centre for Renewable Energy and Related Greenhouse Gas Abatement Technologies (ACRE), its technologies, commercial relationships and markets. The relevance of ACRE to developing country communities which lack reliable, adequate power supplies, is discussed. The opportunities for mutual collaboration between Australia and the developing countries in the application of renewable energy have never been stronger. Renewable energy promises real advantages to those who deploy it wisely, as well as significant job creation. Education at all level together with operational training, public awareness of what is possible and increased system reliability, are also vital ingredients for acceptance of these new technologies. They underpin successful commercialisation. The author concludes with the hope for a united international cooperative approach to the development of the renewable energy industry. (author)

  4. Promoting renewable energy technologies

    International Nuclear Information System (INIS)

    Grenaa Jensen, S.

    2004-06-01

    Technologies using renewable energy sources are receiving increasing interest from both public authorities and power producing companies, mainly because of the environmental advantages they procure in comparison with conventional energy sources. These technologies can be substitution for conventional energy sources and limit damage to the environment. Furthermore, several of the renewable energy technologies satisfy an increasing political goal of self-sufficiency within energy production. The subject of this thesis is promotion of renewable technologies. The primary goal is to increase understanding on how technological development takes place, and establish a theoretical framework that can assist in the construction of policy strategies including instruments for promotion of renewable energy technologies. Technological development is analysed by through quantitative and qualitative methods. (BA)

  5. Renewable Heating And Cooling

    Science.gov (United States)

    Renewable heating and cooling is a set of alternative resources and technologies that can be used in place of conventional heating and cooling technologies for common applications such as water heating, space heating, space cooling and process heat.

  6. Renewable Energy Tracking Systems

    Science.gov (United States)

    Renewable energy generation ownership can be accounted through tracking systems. Tracking systems are highly automated, contain specific information about each MWh, and are accessible over the internet to market participants.

  7. Renewable energy in Taiwan

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Falin; Lu, Shyi-Min; Wang, Eric; Tseng, Kuo-Tung [Institute of Applied Mechanics, National Taiwan University, Taipei 10617 (China)

    2010-09-15

    With limited indigenous conventional energy resources, Taiwan imports over 99% of its energy supply from foreign countries, mostly from the Middle East. Developing independent renewable energy resources is thus of priority concern for the Taiwanese government. A medium subtropical island surrounded by the Pacific Ocean, Taiwan has enormous potential to develop various renewable energies, such as solar energy, biomass energy, wind power, geothermal energy, hydropower, etc. However, owing to the importance of conventional fossil energy in generating exceptionally cheap electricity, renewable energy has not yet fully developed in Taiwan, resulting from a lack of market competition. Consequently, numerous promotional and subsidy programs have recently been proclaimed by the Taiwanese government, focused on the development of various renewables. This study reviews the achievements, polices and future plans in this area. (author)

  8. Renewable Substitutability Index: Maximizing Renewable Resource Use in Buildings

    Science.gov (United States)

    In order to achieve a material and energy balance in buildings that is sustainable in the long run, there is an urgent need to assess the renewable and non-renewable resources used in the manufacturing process and to progressively replace non-renewable resources with renewables. ...

  9. License renewal process

    International Nuclear Information System (INIS)

    Fable, D.; Prah, M.; Vrankic, K.; Lebegner, J.

    2004-01-01

    The purpose of this paper is to provide information about license renewal process, as defined by Nuclear Regulatory Commission (NRC). The Atomic Energy Act and NRC regulations limit commercial power reactor licenses to an initial 40 years but also permit such licenses to be renewed. This original 40-year term for reactor licenses was based on economic and antitrust considerations not on limitations of nuclear technology. Due to this selected time period; however, some structures and components may have been engineered on the basis of an expected 40-year service life. The NRC has established a timely license renewal process and clear requirements codified in 10 CFR Part 51 and 10 CFR Part 54, that are needed to assure safe plant operation for extended plant life. The timely renewal of licenses for an additional 20 years, where appropriate to renew them, may be important to ensuring an adequate energy supply during the first half of the 21st Century. License renewal rests on the determination that currently operating plants continue to maintain adequate levels of safety, and over the plant's life, this level has been enhanced through maintenance of the licensing bases, with appropriate adjustments to address new information from industry operating experience. Additionally, NRC activities have provided ongoing assurance that the licensing bases will continue to provide an acceptable level of safety. This paper provides additional discussion of license renewal costs, as one of key elements in evaluation of license renewal justifiability. Including structure of costs, approximately value and two different approaches, conservative and typical. Current status and position of Nuclear Power Plant Krsko, related to license renewal process, will be briefly presented in this paper. NPP Krsko is designed based on NRC Regulations, so requirements from 10 CFR 51, and 10 CFR 54, are applicable to NPP Krsko, as well. Finally, this paper will give an overview of current status of

  10. Processes of Strategic Renewal,

    OpenAIRE

    Harald Aadne, John; Mahnke, Volker

    2010-01-01

    We discuss strategic renewal from a competence perspective. We argue that the management of speed and timing in this process is viewed distinctively when perceived through a cognitive lens. Managers need more firmly grounded process-understanding. The key idea of this paper is to dynamically conceptualize key activities of strategic renewal, and possible sources of break-down as they relate to the managment of speed and timing. Based on a case from the media industry, we identi...

  11. Promoting renewable energy technologies

    DEFF Research Database (Denmark)

    Olsen, O.J.; Skytte, K.

    2004-01-01

    % of its annual electricity production. In this paper, we present and discuss the Danish experience as a case of promoting renewable energy technologies. The development path of the two technologies has been very different. Wind power is considered an outright success with fast deployment to decreasing...... technology and its particular context, it is possible to formulate some general principles that can help to create an effective and efficient policy for promoting new renewable energy technologies....

  12. Identifying the hotspots of non-renewable water use using HiGW-MAT: A new land surface model coupled with human interventions and ground water reservoir

    Science.gov (United States)

    Oki, T.; Pokhrel, Y. N.; Yeh, P. J.; Koirala, S.; Kanae, S.; Hanasaki, N.

    2011-12-01

    The real hydrological cycles on the Earth are not natural anymore. Global hydrological model simulations of the water cycle and available water resources should have an ability to consider the effects of human interventions on hydrological cycles. Anthropogenic activity modules (Hanasaki et al., 2008), such as reservoir operation, crop growth and water demand in crop lands, and environmental flows, were incorporated into a land surface model called MATSIRO (Takata et al., 2003), to form a new model, MAT-HI (Pokhrel et al., 2011). Total terrestrial water storages (TWS) in large river basins were estimated using the new model by off-line simulation, and compared with the TWS observed by GRACE for 2002-2007. The results showed MAT-HI has an advantage estimating TWS particularly in arid river basins compared with H08 (Hanasaki et al., 2008). MAT-HI was further coupled with a module representing the ground water level fluctuations (Yeh et al., 2005), and consists a new land surface scheme HiGW-MAT (Human Intervention and Ground Water coupled MATSIRO). HiGW-MAT is also associated with a scheme tracing the origin and flow path with the consideration on the sources of water withdrawal from stream flow, medium-size reservoirs and nonrenewable groundwater in addition to precipitation to croplands enabled the assessment of the origin of water producing major crops as Hanasaki et al. (2010). Areas highly dependent on nonrenewable groundwater are detected in the Pakistan, Bangladesh, western part of India, north and western parts of China, some regions in the Arabian Peninsula and the western part of the United States through Mexico. Cumulative nonrenewable groundwater withdrawals estimated by the model are corresponding fairly well with the country statistics of total groundwater withdrawals. Ground water table depletions in large aquifers in US estimated by HiGW-MAT were compared with in-situ observational data, and the correspondences are very good. Mean global exploitation

  13. Renewable energy in Europe

    International Nuclear Information System (INIS)

    Deshaies, M.

    2009-01-01

    Europe's increasing demand for energy and its environmental preoccupations are creating a favourable environment for the development of renewable energy sources. This article stated that although many European countries have adopted voluntary policies since the 1990s to increase the use of renewable energy sources, they have not been developed in an equal or consistent manner. A table was included to show the consumption of renewable energies by country; the percentage of renewable energies in 1995 as compared to 2006; and the consumption of primary energy resources. Combined, Germany, Spain and Denmark produce 75 per cent of wind energy in Europe, while 75 per cent of Europe's hydroelectricity is produced in Norway, Sweden, France, Italy, Austria and Switzerland. Germany has also made significant contributions in developing biomass energy. The article emphasized that the development of renewable energy sources is limited by the fact that it cannot keep up with growing energy demands. In addition, renewable energies cannot yet replace all fossil fuel consumption in Europe because of the variation in development from one country to another. 1 ref., 2 tabs., 4 figs.

  14. Metallic and Insulating Interfaces of Amorphous SrTiO3-Based Oxide Heterostructures

    DEFF Research Database (Denmark)

    Chen, Yunzhong; Pryds, Nini; Kleibeuker, Josée E.

    2011-01-01

    AlO3, SrTiO3, and yttria-stabilized zirconia films. On the other hand, samples of amorphous La7/8Sr1/8MnO3 films on SrTiO3 substrates remain insulating. The interfacial conductivity results from the formation of oxygen vacancies near the interface, suggesting that the redox reactions on the surface...

  15. Some advance on the comprehension of SR analysis for estimating the flux of a scalar

    Science.gov (United States)

    Castellví, Dr

    2009-04-01

    In agronomy, the eddy covariance, EC, method likely is the preferred for measuring surface scalar fluxes. For latent heat flux, however, weighing lysimeters maybe preferred in agriculture, but they are rarely affordable and not portable. The dissipation method, DM, is considered the most reliable technique for measuring scalar fluxes over open water because instrument motion contaminates the EC measurements. The main advantage of DM over EC is that it is less sensitive to low frequency instrument platform motions (such as ship and buoys), sensor alignment, precise orientation and stringent steadiness in the mean meteorological conditions (Fairall and Larsen, 1986; Kader, 1992; Edson and Fairall, 1998). Over land, keeping in mind that the EC and DM methods require the same measurements for scalar flux measurement, the DM has several disadvantages versus the EC. Direct measurement of the scalar variance dissipation rate, VDR, requires to capture eddies in the Kolmogorov's microscale (thus scalar time series measured at frequencies in the order of kHz are needed). Therefore, it is not practical. Indirect methods to estimate VDR (such as spectral analysis and second or third order structure functions) requires implementing iterative methods involving similarity relationships that are not well established (Hsieh and Katul, 1997; Castellvi and Snyder, 2008). Currently, there is ample evidence that the DM as explained in traditional micrometeorological books (such as, Panofsky and Dutton, 1984; Brutsaert, 1988; Kaimal and Finnigan; 1994) is, in general, not correct. Accordingly, it likely explains why DM is typically omitted in revisits of micrometeorological methods for estimating scalar fluxes in agronomy. Within the last decade, over some agricultural surfaces, evidence has been shown on the advantages over other micrometeorological methods and the reliability (i.e., close performance to the EC method) of Surface Renewal, SR, theory in conjunction with the Analysis of

  16. Dosimetry of Sr-90 ophthalmic applicators

    International Nuclear Information System (INIS)

    Reft, C.S.; Kuchnir, F.T.; Rosenberg, I.; Myrianthopoulos, L.C.

    1990-01-01

    Sr-90 ophthalmic applicators are commonly used for the treatment of superficial eye disorders. Although a variety of dosimetric devices such as film, thermoluminescent dosimeters (TLD's), ion chambers, and radiochromic foils have been used to measure the peak dose at the applicator surface, there is no internationally agreed upon calibration procedure. Recently, large discrepancies among calibrations of the same applicator at three institutions have been reported. Here we describe a technique to obtain the peak dose rate at the applicator surface using LiF TLD's. The technique can be used for the calibration of flat as well as curved surface applicators. Results for two flat and three concave applicators are presented. Our measurement of the surface dose rate for one of the flat applicators is compared with those obtained by four other institutions, each using different dosimetric devices

  17. 2016 Renewable Energy Data Book

    Energy Technology Data Exchange (ETDEWEB)

    2017-12-29

    The 2016 Renewable Energy Data Book provides facts and figures on energy and electricity use, renewable electricity in the United States, global renewable energy development, wind power, solar power, geothermal power, biopower, hydropower, marine and hydrokinetic power, hydrogen, renewable fuels, and clean energy investment.

  18. 2015 Renewable Energy Data Book

    Energy Technology Data Exchange (ETDEWEB)

    Beiter, Philipp [National Renewable Energy Lab. (NREL), Golden, CO (United States); Tian, Tian [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2016-11-01

    The Renewable Energy Data Book for 2015 provides facts and figures on energy and electricity use, renewable electricity in the United States, global renewable energy development, wind power, solar power, geothermal power, biopower, hydropower, marine and hydrokinetic power, hydrogen, renewable fuels, and clean energy investment.

  19. 2015 Renewable Energy Data Book

    Energy Technology Data Exchange (ETDEWEB)

    Beiter, Philipp; Tian, Tian

    2016-11-01

    The 2015 Renewable Energy Data Book provides facts and figures on energy and electricity use, renewable electricity in the United States, global renewable energy development, wind power, solar power, geothermal power, biopower, hydropower, marine and hydrokinetic power, hydrogen, renewable fuels, and clean energy investment.

  20. 2014 Renewable Energy Data Book

    Energy Technology Data Exchange (ETDEWEB)

    Beiter, Philipp

    2015-11-01

    The Renewable Energy Data Book for 2014 provides facts and figures on energy and electricity use, renewable electricity in the United States, global renewable energy development, wind power, solar power, geothermal power, biopower, hydropower, marine and hydrokinetic power, hydrogen, renewable fuels, and clean energy investment.

  1. Sr-containing hydroxyapatite: morphologies of HA crystals and bioactivity on osteoblast cells

    Energy Technology Data Exchange (ETDEWEB)

    Aina, Valentina [Department of Chemistry, Università degli Studi di Torino, Via P. Giuria 7, 10125 Torino (Italy); Centre of Excellence NIS (Nanostructured Interfaces and Surface) Università degli Studi di Torino (Italy); INSTM (Italian National Consortium for Materials Science and Technology), UdR Università di Torino (Italy); Bergandi, Loredana, E-mail: loredana.bergandi@unito.it [Department of Oncology, Università degli Studi di Torino, Via Santena 5/bis, 10126 Torino (Italy); Lusvardi, Gigliola; Malavasi, Gianluca [Department of Chemical and Geological Sciences, Università di Modena and Reggio Emilia, Via Campi 183, 41125 Modena (Italy); Imrie, Flora E.; Gibson, Iain R. [School of Medical Sciences, Institute of Medical Sciences, University of Aberdeen, Foresterhill, Aberdeen, AB25 2ZD (United Kingdom); Cerrato, Giuseppina [Department of Chemistry, Università degli Studi di Torino, Via P. Giuria 7, 10125 Torino (Italy); Centre of Excellence NIS (Nanostructured Interfaces and Surface) Università degli Studi di Torino (Italy); INSTM (Italian National Consortium for Materials Science and Technology), UdR Università di Torino (Italy); Ghigo, Dario [Department of Oncology, Università degli Studi di Torino, Via Santena 5/bis, 10126 Torino (Italy)

    2013-04-01

    A series of Sr-substituted hydroxyapatites (HA), of general formula Ca{sub (10−x)}Sr{sub x}(PO{sub 4}){sub 6}(OH){sub 2}, where x = 2 and 4, were synthesized by solid state methods and characterized extensively. The reactivity of these materials in cell culture medium was evaluated, and the behavior towards MG-63 osteoblast cells (in terms of cytotoxicity and proliferation assays) was studied. Future in vivo studies will give further insights into the behavior of the materials. A paper by Lagergren et al. (1975), concerning Sr-substituted HA prepared by a solid state method, reports that the presence of Sr in the apatite composition strongly influences the apatite diffraction patterns. Zeglinsky et al. (2012) investigated Sr-substituted HA by ab initio methods and Rietveld analyses and reported changes in the HA unit cell volume and shape due to the Sr addition. To further clarify the role played by the addition of Sr on the physico-chemical properties of these materials we prepared Sr-substituted HA compositions by a solid state method, using different reagents, thermal treatments and a multi-technique approach. Our results indicated that the introduction of Sr at the levels considered here does influence the structure of HA. There is also evidence of a decrease in the crystallinity degree of the materials upon Sr addition. The introduction of increasing amounts of Sr into the HA composition causes a decrease in the specific surface area and an enrichment of Sr-apatite phase at the surface of the samples. Bioactivity tests show that the presence of Sr causes changes in particle size and/or morphology during soaking in MEM solution; on the contrary the morphology of pure HA does not change after 14 days of reaction. The presence of Sr, as Sr-substituted HA and SrCl{sub 2,} in cultures of human MG-63 osteoblasts did not produce any cytotoxic effect. In fact, Sr-substituted HA increased the proliferation of osteoblast cells and enhanced cell differentiation: Sr in

  2. Sr-containing hydroxyapatite: morphologies of HA crystals and bioactivity on osteoblast cells

    International Nuclear Information System (INIS)

    Aina, Valentina; Bergandi, Loredana; Lusvardi, Gigliola; Malavasi, Gianluca; Imrie, Flora E.; Gibson, Iain R.; Cerrato, Giuseppina; Ghigo, Dario

    2013-01-01

    A series of Sr-substituted hydroxyapatites (HA), of general formula Ca (10−x) Sr x (PO 4 ) 6 (OH) 2 , where x = 2 and 4, were synthesized by solid state methods and characterized extensively. The reactivity of these materials in cell culture medium was evaluated, and the behavior towards MG-63 osteoblast cells (in terms of cytotoxicity and proliferation assays) was studied. Future in vivo studies will give further insights into the behavior of the materials. A paper by Lagergren et al. (1975), concerning Sr-substituted HA prepared by a solid state method, reports that the presence of Sr in the apatite composition strongly influences the apatite diffraction patterns. Zeglinsky et al. (2012) investigated Sr-substituted HA by ab initio methods and Rietveld analyses and reported changes in the HA unit cell volume and shape due to the Sr addition. To further clarify the role played by the addition of Sr on the physico-chemical properties of these materials we prepared Sr-substituted HA compositions by a solid state method, using different reagents, thermal treatments and a multi-technique approach. Our results indicated that the introduction of Sr at the levels considered here does influence the structure of HA. There is also evidence of a decrease in the crystallinity degree of the materials upon Sr addition. The introduction of increasing amounts of Sr into the HA composition causes a decrease in the specific surface area and an enrichment of Sr-apatite phase at the surface of the samples. Bioactivity tests show that the presence of Sr causes changes in particle size and/or morphology during soaking in MEM solution; on the contrary the morphology of pure HA does not change after 14 days of reaction. The presence of Sr, as Sr-substituted HA and SrCl 2, in cultures of human MG-63 osteoblasts did not produce any cytotoxic effect. In fact, Sr-substituted HA increased the proliferation of osteoblast cells and enhanced cell differentiation: Sr in HA has a positive effect

  3. Trace determination of 90Sr and 89Sr in environmental samples by collinear resonance ionization spectroscopy

    International Nuclear Information System (INIS)

    Lantzsch, J.; Bushaw, B. A.; Bystrow, V. A.; Herrmann, G.; Kluge, H.-J.; Niess, S.; Otten, E. W.; Passler, G.; Schwalbach, R.; Schwarz, M.; Stenner, J.; Trautmann, N.; Wendt, K.; Yushkevich, Y. V.; Zimmer, K.

    1995-01-01

    Collinear resonance ionization spectroscopy has been developed as a sensitive technique for fast trace detection of 90 Sr and 89 Sr in the environment. A detection limit for 90 Sr of 10 7 atoms in the presence of 10 17 atoms in the presence of 10 17 atoms of stable Strontium has been achieved, while the applicability of the method has been demonstrated on real world samples. After collection and chemical separation, strontium is surface ionized, accelerated to 33keV and mass separated. The ions are neutralized and the emerging fast atoms interact with an argon ion laser beam (γ=364 nm) in a quasi-collinear geometry. Optical excitation starts from the long-lived 5s4d 3 D2 state of strontium, which is populated in the charge exchange process, and the fast atoms are selectively excited into the high-lying 5s23f 3 F3 Rydberg state. The Rydberg-atoms are subsequently field-ionized and detected by a channeltron detector after energy selection. The described method was successfully used to determine the 90 Sr-content in air samples collected near Munich during the Chernobyl reactor accident in April 1986

  4. Sr isotope tracing of multiple water sources in a complex river system, Noteć River, central Poland

    Energy Technology Data Exchange (ETDEWEB)

    Zieliński, Mateusz, E-mail: mateusz.zielinski@amu.edu.pl [Institute of Geoecology and Geoinformation, Adam Mickiewicz University, Dzięgielowa 27, 61-680 Poznań (Poland); Dopieralska, Jolanta, E-mail: dopieralska@amu.edu.pl [Poznań Science and Technology Park, Adam Mickiewicz University Foundation, Rubież 46, 61-612 Poznań (Poland); Belka, Zdzislaw, E-mail: zbelka@amu.edu.pl [Isotope Laboratory, Adam Mickiewicz University, Dzięgielowa 27, 61-680 Poznań (Poland); Walczak, Aleksandra, E-mail: awalczak@amu.edu.pl [Isotope Laboratory, Adam Mickiewicz University, Dzięgielowa 27, 61-680 Poznań (Poland); Siepak, Marcin, E-mail: siep@amu.edu.pl [Institute of Geology, Adam Mickiewicz University, Maków Polnych 16, 61-606 Poznań (Poland); Jakubowicz, Michal, E-mail: mjakub@amu.edu.pl [Institute of Geoecology and Geoinformation, Adam Mickiewicz University, Dzięgielowa 27, 61-680 Poznań (Poland)

    2016-04-01

    Anthropogenic impact on surface waters and other elements in the environment was investigated in the Noteć River basin in central Poland. The approach was to trace changes in the Sr isotope composition ({sup 87}Sr/{sup 86}Sr) and concentration in space and time. Systematic sampling of the river water shows a very wide range of {sup 87}Sr/{sup 86}Sr ratios, from 0.7089 to 0.7127. This strong variation, however, is restricted to the upper course of the river, whereas the water in the lower course typically shows {sup 87}Sr/{sup 86}Sr values around 0.7104–0.7105. Variations in {sup 87}Sr/{sup 86}Sr are associated with a wide range of Sr concentrations, from 0.14 to 1.32 mg/L. We find that strong variations in {sup 87}Sr/{sup 86}Sr and Sr concentrations can be accounted for by mixing of two end-members: 1) atmospheric waters charged with Sr from the near-surface weathering and wash-out of Quaternary glaciogenic deposits, and 2) waters introduced into the river from an open pit lignite mine. The first reservoir is characterized by a low Sr content and high {sup 87}Sr/{sup 86}Sr ratios, whereas mine waters display opposite characteristics. Anthropogenic pollution is also induced by extensive use of fertilizers which constitute the third source of Sr in the environment. The study has an important implication for future archeological studies in the region. It shows that the present-day Sr isotope signatures of river water, flora and fauna cannot be used unambiguously to determine the “baseline” for bioavailable {sup 87}Sr/{sup 86}Sr in the past. - Highlights: • Sr isotopes fingerprint water sources and their interactions in a complex river system. • Mine waters and fertilizers are critical anthropogenic additions in the river water. • Limited usage of environmental isotopic data in archeological studies. • Sr budget of the river is dynamic and temporary.

  5. Nonlocal Coulomb correlations in pure and electron-doped Sr2IrO4 : Spectral functions, Fermi surface, and pseudo-gap-like spectral weight distributions from oriented cluster dynamical mean-field theory

    Science.gov (United States)

    Martins, Cyril; Lenz, Benjamin; Perfetti, Luca; Brouet, Veronique; Bertran, François; Biermann, Silke

    2018-03-01

    We address the role of nonlocal Coulomb correlations and short-range magnetic fluctuations in the high-temperature phase of Sr2IrO4 within state-of-the-art spectroscopic and first-principles theoretical methods. Introducing an "oriented-cluster dynamical mean-field scheme", we compute momentum-resolved spectral functions, which we find to be in excellent agreement with angle-resolved photoemission spectra. We show that while short-range antiferromagnetic fluctuations are crucial to accounting for the electronic properties of Sr2IrO4 even in the high-temperature paramagnetic phase, long-range magnetic order is not a necessary ingredient of the insulating state. Upon doping, an exotic metallic state is generated, exhibiting cuprate-like pseudo-gap spectral properties, for which we propose a surprisingly simple theoretical mechanism.

  6. Nature and Significance of the High-Sr Aleutian Lavas

    Science.gov (United States)

    Yogodzinski, G. M.; Arndt, S.; Turka, J. R.; Kelemen, P. B.; Vervoort, J. D.; Portnyagin, M.; Hoernle, K.

    2011-12-01

    Results of the Western Aleutian Volcano Expedition and German-Russian KALMAR cruises include the discovery of seafloor volcanism at the Ingenstrem Depression and at unnamed seamounts 300 km west of Buldir, the westernmost emergent volcano in the Aleutian arc. These discoveries indicate that the surface expression of active Aleutian volcanism goes below sea level just west of Buldir, but is otherwise continuous along the full length of the arc. Many lavas dredged from western Aleutian seamounts are basalts, geochemically similar to basalts from elsewhere in Aleutians and other arcs (La/Yb 4-8, Sr/Y700 ppm Sr), which are mostly plagioclase-hornblende andesites and dacites with low Y and middle-heavy rare-earth elements, fractionated trace element patterns (Sr/Y=50-200, La/Yb=9-25) and MORB-like isotopes (87Sr/86Sr 0.65) with 1250-1700 ppm Sr, 4-7 ppm Y, low abundances of all rare-earth elements (LaMexico. [1] Zimmer et al., 2010, J. Petrology, v. 51, p. 2411

  7. Renewable Energy in China

    Directory of Open Access Journals (Sweden)

    Valery I. Salygin

    2015-01-01

    Full Text Available China is the most densely populated country in the world with high rate of economic growth resulting in higher demand for energy resources and in strive to guarantee stable supply of these resources. Chinese annual GDP growth in 2012 and 2013 was down to 7.7% comparing to 10% in 2000-2011 [7]. In 2012 and 2013 economic growth stumbled because of slowdown in manufacturing and exports, taking into account that Chinese government was eager to cut inflation and excessive investments in some segments of the market. Speaking about energy sector Chinese government is aimed at promotion of market-based pricing systems, activities for advanced energy efficiency and higher competition between energy companies, and increased investment in renewable energy resources. Considering renewables as one of many ways to diversify energy supplies, lower dependence on coal and improve environmental situation Chinese government actively supports and develops programs aimed at support of renewable energy industry in China. Chinese economic development is tightly attached to five-year plans. It seems important to mention the fact that main energy goals for current 12-th "five-year plan" are to achieve 15% renewables consumption and CO2 sequestration up to 40-45% by2020 in order to lower dependency on coal and improve environmental situation. As a result of Chinese state policy to develop renewables China achieved certain results in wind energy, helioenergetics, hydroenergetics and energy from waste recycling.

  8. Renewable energy handbook

    Energy Technology Data Exchange (ETDEWEB)

    Fine, R

    1976-01-01

    The potential for renewable energy use in Canada is examined. It is pointed out that Canada can choose to begin to diversify its energy supply now, moving rapidly and smoothly towards an efficient energy society based on renewable energy sources; or, it can continue on its present course and face the possibility of being forced by necessity to make a later transition to renewable sources, probably with a great deal of economic and political disruption. The handbook begins with a discussion on major issues and options available. This second section deals with the technology, applications, and costs of direct solar energy utilization, solar thermal electricity generation, photovoltaic conversion, wind energy, biomass energy, tidal power, wave energy, ocean thermal energy, geothermal energy, heat pumps, and energy storage. Section three discusses how renewable energy might realistically supply Canada's energy requirements within a reasonable period of time. Some issues on how government, industry, and the individual may become involved to make this happen are suggested. A list of resource people and renewable energy businesses is provided in the last section. A recommended reading list and bibliography complete the handbook. (MCW)

  9. Art : accessible, renewable technology

    International Nuclear Information System (INIS)

    Middleton, C.D.

    2004-01-01

    This paper focuses on the role of non-governmental organization (NGO) citizen groups in Ontario in the use and production of electricity. NGOs have the potential to act both directly on their own accord, and indirectly by pressuring government and others. Current demand for electricity is divided between industrial, commercial and residential users. Citizens have an important role to play in reducing energy demand. On the supply side, there is a revival of interest in renewable energy based on wind, photovoltaic and local-hydro technologies as a result of the escalating environmental and economic costs of coal and nuclear generation. However, citizen groups have greater interest and enthusiasm than technical expertise, creating a mismatch between technological solutions and human need or use of them. This paper discusses how this mismatch applies to renewable-energy technologies, many of which are not especially user-friendly, or accessible. While alternative technologies are increasingly welcomed by government, industry is developing a large and growing array of technological devices. In between this is the citizen, who, despite keen interest, can be overwhelmed by the complexity of the situation. This paper links the theoretical perspective to the real world with a discussion of the dynamics between people and renewable energy in citizen groups and makes particular reference to one group, Citizens for Renewable Energy, that has been making renewable energy technology more accessible to its members for over a decade

  10. Subsidies for renewable energy?

    International Nuclear Information System (INIS)

    Skytte, K.; Grenaa Jensen, S.; Morthorst, P.E.; Olsen, O.J.

    2004-01-01

    Ambitious Danish and European energy and environment objectives make a point of using renewable energy sources in the electricity supply. Denmark has been leading country in successful development and commercialization of wind turbines and is as yet one of the leading manufacturers of the world. Danish governments have successfully invested a lot in this development. Other countries have spent more money without achieving a similar success. The questions are why things have gone so well in Denmark and if the Danish success can be repeated for other renewable energy technologies. The starting point of this book is that a political decision on subsidizing the developmental process of a specific technology not in itself guarantees that the technology will turn out reliable and efficient enough to compete successfully in a liberalized electricity market. An understanding of this development is necessary in order to affect a technological development. This book goes through the development of different renewable energy technologies and two theories used for discussing the technological development: experience curves and innovation theory. Based on the discussions and a description of causal relations, an analytical model for different phases of renewable energy technologies' developmental progress and technological life cycle is made. The model is used for evaluating the subsidies for chosen renewable technologies in Denmark. With wind energy as example an analysis of what went well or badly, what might be done and which actions might be efficient is made. (BA)

  11. The 90Sr, 137Cs, 3H and 131I content in surface water and sediments of the Danube, Olt and Arges river and in milk samples for the year 1972

    International Nuclear Information System (INIS)

    Podeanu, G.; Iancu, E.

    1975-01-01

    The radioactivity of the measured radionuclides in water decreased from their discharge into the Danube to the mouth of the river. The amounts of certain radioisotopes in water samples, sediments, and milk are far below the maximum permissible concentrations. With some exceptions, the radioactivity of 137 Cs is lower than that of 90 Sr. With some exceptions, the highest values for the radionuclides studied were measured during the summer months. (orig./RW) [de

  12. XPS study of surface state of novel perovskite system Dy{sub 0.5}Sr{sub 0.5}Co{sub 0.8}Fe{sub 0.2}O{sub 3-δ} as cathode for solid oxide fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Kautkar, Pranay R.; Acharya, Smita A., E-mail: saha275@yahoo.com; Tumram, Priya V. [Depatment of Physics, Rashtrasant Tukadoji Maharaj Nagpur University Campus, Nagpur-440033 (India); Deshpande, U. P. [UGC-DAE Consortium for scientific Research, University Campus, Khandwa Road, Indore-452001, Madhya Pradesh,India (India)

    2016-05-06

    In the present attempt,novel perovskite oxide Dy{sub 0.5}Sr{sub 0.5}Co{sub 0.8}Fe{sub 0.2}O{sub 3–δ} (DSCF) as cathode material has been synthesized by an Ethylene glycol-citrate combined sol-gel combustion route. Orthorhombic symmetry structure is confirmed by X-ray diffraction (XRD) and data is well fitted using Rietveld refinement by Full-Prof software suite. Chemical natureof surface of DSCF has been analyzed by using X-ray photoelectron spectroscopy (XPS). XPS result shows that Dy ions are in +3 oxidation state and Sr in +2 states. However Co2p and Fe2p spectra indicates partial change in oxidation state from Co3+/Fe3+ to Co4+/Fe4+. These attribute to develop active sites on the surface for oxygen ions. O1s XPS spectra shows two oxygen peaks relatedto lattice oxygen in perovskite and absorbed oxygen in oxygen vacancy are detected. O1s spectra demonstrate the existence of adsorbed oxygen species on the surface of DSCF oxide which is quite beneficial for intermediate temperature of Solid Oxide Fuel Cell.

  13. Tracing sediment sources in upstream agricultural catchments: contribution of elemental geochemistry, 87Sr/86Sr ratio and radionuclides measurements

    International Nuclear Information System (INIS)

    Le-Gall, Marion

    2016-01-01

    Soil erosion is recognized as one of the main processes of land degradation in agricultural environments. This study develops an original fingerprinting method to examine sediment source contributions in two contrasted agricultural catchments. Several properties were used to trace sediment lithological sources ( 87 Sr/ 86 Sr ratios, elemental concentrations), soil surface and subsurface sources ( 137 Cs) and to quantify their temporal dynamics ( 7 Be, 210 Pb xs ). In the Louroux catchment (24 km 2 , France), representative of drained areas of Northwestern Europe, results showed the dominant contribution of very fine particles (≤2 μm) transiting through the tile drainage system to suspended sediment. Sediment accumulated in the river channel was mainly exported during the two first floods investigated in 2013 whereas the next event was characterized by the transport of sediment eroded from the cultivated soil surface. Mixing models were used, and results indicated that surface sources contributed the majority of sediment deposited in the pond, at the outlet of the catchment. The two lithological sources, discriminated using 87 Sr/ 86 Sr ratios, contributed in similar proportions to downstream pond sediment. In contrast, significant variations were observed since the 1950's. These changes may be related to the progressive implementation of land consolidation schemes within the catchment. Results obtained in the Louroux catchment revealed the potential of 87 Sr/ 86 Sr ratios to trace sediment lithological sources. The methodology was then applied to the larger and steeper Guapore catchment (2000 km 2 , Brazil), exposed to a more erosive climate and characterized by contrasted laterite soils. 87 Sr/ 86 Sr ratios and elements that discriminated the five soil types found in the catchment were incorporated in mixing models. Results showed that the major part of sediment was supplied by soils located in lower catchment parts. This result suggests the higher

  14. 44/40Ca and 87Sr/86Sr isotopes as tracers of silicate weathering in small catchments of the Massif Central, France

    Science.gov (United States)

    Négrel, Philippe; Guerrot, Catherine; Millot, Romain; Petelet-Giraud, Emmanuelle; Bullen, Thomas

    2013-04-01

    We present calcium stable isotope and strontium radiogenic isotope data for soils and sediments developed on volcanic and igneous rocks forming small catchments in the Massif Central (France). Measurements of 44/40Ca isotope ratios (44/40Ca measured by the double spike method on TIMS and normalized to the value for seawater Ca in delta units) in rocks, sediments and soils from silicate catchments (e.g. granite and basalts) together with 87Sr/86Sr isotope ratios permit an examination of the relationships of these isotope systematics during weathering of silicate rocks. We have analysed the granite, weathered granite (arene) and saprolite, sediment and soil overlying the granite on one hand and the basanite, sediment and soil overlying the basanite on the other. The main bedrock in the volcanic zone (e.g. Allanche catchment) is 11 to 2.5 Ma basanite (nephelinitic to leucitic basalts) having SiO2 between 41-45 wt. %, Na2O + K2O bank have 87Sr/86Sr ratios greater than that of the arene with values increasing in the sediment from the surface down to soil. The 87Sr/86Sr vs. Rb/Sr variation observed in the volcanic area likewise confirms the weathering of low 87Sr/86Sr, low Rb/Sr phases in the bedrock, and there is a linear increase in 87Sr/86Sr and Rb/Sr ratios from those in the sediment up to the values observed in the soils. In the volcanic area, the basanite bedrock has 44/40Ca = -0.94 ± 0.05‰ (n = 7), while the soils and sediments have 44/40Ca of -0.75 to -1.13‰ and -0.79 to -1.01‰, respectively. These results suggest that Ca isotopes are not strongly fractionated during weathering of the basalt. The granite whole-rock has 44/40Ca of -1.29‰, while the soil and sediments have 44/40Ca of -1.93 to -2.07‰ and -1.98 to -2.81‰, respectively, with values decreasing as the Ca content decreases. The 44/40Ca ratios of arene, soil and sediment are similar to or less than that of K- feldspar, reflecting complete loss of the relatively heavy Ca from plagioclase and

  15. The influence of Sr on the microstructure, degradation and stress corrosion cracking of the Mg alloys - ZK40xSr.

    Science.gov (United States)

    Chen, Lianxi; Bin, Yuanhong; Zou, Wenqi; Wang, Xiaojian; Li, Wei

    2017-02-01

    In the present work, new magnesium (Mg) alloys (Mg-4Zn-0.6Zr-xSr, x=0, 0.4, 0.8, 1.2, 1.6wt%; ZK40xSr) were prepared and studied as potential biodegradable materials. The influence of strontium (Sr) addition on the properties of the new Mg alloys was investigated, which included microstructure, corrosion degradation, and the stress corrosion cracking (SCC) susceptibility. The average grain size of the ZK40Sr was approximately 100µm, which was significantly smaller than that of ZK40 alloy without Sr (402.3±40.2µm). The size of grain boundaries precipitates in the ZK40xSr alloys gradually increased with the increase of Sr content. The grain boundaries finally showed a continuously distribution and net-like shape. The degradation test showed that the average degradation rate of the ZK40xSr alloys increased with the increase of Sr addition. In the case of Mg-4Zn-0.6Zr, the degradation rate was 2.2mgcm -2 day -1 , which was lower than that of Mg-4Zn-0.6Zr-1.6Sr (4.93mgcm -2 day -1 ). When the ZK40xSr alloys were immersed in m-SBF, the rod-like Sr-contained hydroxyapatite (HA) substance was detected, which was known to enhance cell growth around bone implants. The fracture surfaces of the as-cast Mg-4Zn-0.6Zr-1.6Sr were shown intergranular stress corrosion cracking (IGSCC) patterns. The increase of SCC susceptibility of the higher Sr ZK40xSr alloys was attributed to the increase of micro-galvanic corrosion between the α-Mg and the grain boundaries precipitates. The SCC susceptibility values were ≈0.13 and ≈0.41 for the Mg-4Zn-0.6Zr-0.4Sr and the Mg-4Zn-0.6Zr-1.6Sr, respectively. Copyright © 2016 Elsevier Ltd. All rights reserved.

  16. Worldwide deposition of 90Sr through 1984

    International Nuclear Information System (INIS)

    Larsen, R.J.; Juzdan, Z.R.

    1986-10-01

    The deposition of 90 Sr in the Northern Hemisphere during 1984 was 0.3 PBq (0.008 MCi), while that of the Southern Hemisphere was 0.1 PBq (0.003 MCi). This resulted in a total deposition on the surface of the earth during 1984 of 0.4 PBq (0.011 MCi). This is the lowest total yearly deposit since the initiation of the Environmental Measurements Laboratory's global fallout program in the mid-1950's. The worldwide cumulative deposit decreased to 357 PBq (9.6 MCi)

  17. Atomic layer epitaxy of Ruddlesden-Popper SrO(SrTiO3)n films by means of metalorganic aerosol deposition

    International Nuclear Information System (INIS)

    Jungbauer, M.; Hühn, S.; Moshnyaga, V.; Egoavil, R.; Tan, H.; Verbeeck, J.; Van Tendeloo, G.

    2014-01-01

    We report an atomic layer epitaxial growth of Ruddlesden-Popper (RP) thin films of SrO(SrTiO 3 ) n (n = ∞, 2, 3, 4) by means of metalorganic aerosol deposition (MAD). The films are grown on SrTiO 3 (001) substrates by means of a sequential deposition of Sr-O/Ti-O 2 atomic monolayers, monitored in-situ by optical ellipsometry. X-ray diffraction and transmission electron microscopy (TEM) reveal the RP structure with n = 2–4 in accordance with the growth recipe. RP defects, observed by TEM in a good correlation with the in-situ ellipsometry, mainly result from the excess of SrO. Being maximal at the film/substrate interface, the SrO excess rapidly decreases and saturates after 5–6 repetitions of the SrO(SrTiO 3 ) 4 block at the level of 2.4%. This identifies the SrTiO 3 substrate surface as a source of RP defects under oxidizing conditions within MAD. Advantages and limitations of MAD as a solution-based and vacuum-free chemical deposition route were discussed in comparison with molecular beam epitaxy

  18. Atomic layer epitaxy of Ruddlesden-Popper SrO(SrTiO{sub 3}){sub n} films by means of metalorganic aerosol deposition

    Energy Technology Data Exchange (ETDEWEB)

    Jungbauer, M.; Hühn, S.; Moshnyaga, V. [Erstes Physikalisches Institut, Universität Göttingen, Friedrich-Hund-Platz 1, 37077 Göttingen (Germany); Egoavil, R.; Tan, H.; Verbeeck, J.; Van Tendeloo, G. [EMAT, University of Antwerp, Groenenborgerlaan 171, 2020 Antwerp (Belgium)

    2014-12-22

    We report an atomic layer epitaxial growth of Ruddlesden-Popper (RP) thin films of SrO(SrTiO{sub 3}){sub n} (n = ∞, 2, 3, 4) by means of metalorganic aerosol deposition (MAD). The films are grown on SrTiO{sub 3}(001) substrates by means of a sequential deposition of Sr-O/Ti-O{sub 2} atomic monolayers, monitored in-situ by optical ellipsometry. X-ray diffraction and transmission electron microscopy (TEM) reveal the RP structure with n = 2–4 in accordance with the growth recipe. RP defects, observed by TEM in a good correlation with the in-situ ellipsometry, mainly result from the excess of SrO. Being maximal at the film/substrate interface, the SrO excess rapidly decreases and saturates after 5–6 repetitions of the SrO(SrTiO{sub 3}){sub 4} block at the level of 2.4%. This identifies the SrTiO{sub 3} substrate surface as a source of RP defects under oxidizing conditions within MAD. Advantages and limitations of MAD as a solution-based and vacuum-free chemical deposition route were discussed in comparison with molecular beam epitaxy.

  19. EDITORIAL: Renewing energy technology Renewing energy technology

    Science.gov (United States)

    Demming, Anna

    2011-06-01

    Renewable energy is now a mainstream concern among businesses and governments across the world, and could be considered a characteristic preoccupation of our time. It is interesting to note that many of the energy technologies currently being developed date back to very different eras, and even predate the industrial revolution. The fuel cell was first invented as long ago as 1838 by the Swiss--German chemist Christian Friedrich Schönbein [1], and the idea of harnessing solar power dates back to ancient Greece [2]. The enduring fascination with new means of harnessing energy is no doubt linked to man's innate delight in expending it, whether it be to satisfy the drive of curiosity, or from a hunger for entertainment, or to power automated labour-saving devices. But this must be galvanized by the sustained ability to improve device performance, unearthing original science, and asking new questions, for example regarding the durability of photovoltaic devices [3]. As in so many fields, advances in hydrogen storage technology for fuel cells have benefited significantly from nanotechnology. The idea is that the kinetics of hydrogen uptake and release may be reduced by decreasing the particle size. An understanding of how effective this may be has been hampered by limited knowledge of the way the thermodynamics are affected by atom or molecule cluster size. Detailed calculations of individual atoms in clusters are limited by computational resources as to the number of atoms that can studied, and other innovative approaches that deal with force fields derived by extrapolating the difference between the properties of clusters and bulk matter require labour-intensive modifications when extending such studies to new materials. In [4], researchers in the US use an alternative approach, considering the nanoparticle as having the same crystal structure as the bulk but relaxing the few layers of atoms near the surface. The favourable features of nanostructures for catalysis

  20. Renewability of geothermal resources

    Energy Technology Data Exchange (ETDEWEB)

    O' Sullivan, Michael; Yeh, Angus [Department of Engineering Science, University of Auckland, Auckland (New Zealand); Mannington, Warren [Contact Energy Limited, Taupo (New Zealand)

    2010-12-15

    In almost all geothermal projects worldwide, the rate of extraction of heat energy exceeds the pre-exploitation rate of heat flow from depth. For example, current production of geothermal heat from the Wairakei-Tauhara system exceeds the natural recharge of heat by a factor of 4.75. Thus, the current rate of heat extraction from Wairakei-Tauhara is not sustainable on a continuous basis, and the same statement applies to most other geothermal projects. Nevertheless, geothermal energy resources are renewable in the long-term because they would fully recover to their pre-exploitation state after an extended shut-down period. The present paper considers the general issue of the renewability of geothermal resources and uses computer modeling to investigate the renewability of the Wairakei-Tauhara system. In particular, modeling is used to simulate the recovery of Wairakei-Tauhara after it is shut down in 2053 after a hundred years of production. (author)

  1. People and renewable energy

    International Nuclear Information System (INIS)

    Rosenvald, Avo

    2002-01-01

    The use of renewable energy is tightly connected to solving social problems in Estonia by creating more new jobs. It is essential that Estonia should increase the use of biofuels. One of the biofuels, firewood, has been used already for centuries. For wider use of renewable energy in Estonia, it is not enough to rely only on enterprices. Rather, before any serious progress can take place, the state should create the appropriate legal environment. Due to its many social and environmental aspects, renewable energy is more important to the state than a sole enterprice. Unfortunately, Estonian government has been delaying its duties. Estonia has two resources that should be taken advantage of, fertile spare land and people still used to the country life. The country people would get work by growing different energy crops on the spare land. (author)

  2. Understanding renewable energy systems

    Energy Technology Data Exchange (ETDEWEB)

    Quaschning, Volker

    2005-01-15

    Beginning with an overview of renewable energy sources including biomass, hydroelectricity, geothermal, tidal, wind and solar power, this book explores the fundamentals of different renewable energy systems. The main focus is on technologies with high development potential such as solar thermal systems, photovoltaics and wind power. This text not only describes technological aspects, but also deals consciously with problems of the energy industry. In this way, the topics are treated in a holistic manner, bringing together maths, engineering, climate studies and economics, and enabling readers to gain a broad understanding of renewable energy technologies and their potential. The book also contains a free CD-ROM resource, which includes a variety of specialist simulation software and detailed figures from the book. (Author)

  3. Renewables vs fossil fuels

    Energy Technology Data Exchange (ETDEWEB)

    Adams, K. (Energy Research and Development Corporation (Australia))

    1992-01-01

    The paper examines some of the factors which will influence the future mix of energy from fossil fuels and renewable sources in Australia. Aspects covered include: the present energy situation; impact of environmental issues; potential for renewable energy; motivators for change; and research and development. It is concluded that the future for fossil fuels and renewable energy is dependent on a number of complex factors, many of which are currently unknown. The key factor is economic viability and that will be influenced by a range of factors such as policies of the Australian and overseas governments in relation to pollution and environment protection (reflected in the cost of meeting such requirements), exploration and production costs (also influenced by government policies), availability of supply, rate of technological development and the size of export markets. 8 refs., 2 figs., 1 tab.

  4. The adsorption of Sr(II) and Cs(I) ions by irradiated Saccharomyces cerevisiae

    International Nuclear Information System (INIS)

    Yiming Tan; Jundong Feng; Liang Qiu; Zhentian Zhao; Xiaohong Zhang; Haiqian Zhang

    2017-01-01

    Adsorption behavior and mechanism of Sr(II) and Cs(I) in single and binary solutions using irradiated Saccharomyces cerevisiae was investigated. The effects of several environmental factors on Sr(II) and Cs(I) adsorption to irradiated Saccharomyces cerevisiae was determined. The equilibrium experimental data were simulated by different kinetic models and isotherm models. The combined effect of Sr(II) and Cs(I) on Saccharomyces cerevisiae is generally antagonistic. SEM and EDS analyses indicate that crystals formed on the cell surface are precipitate of Sr(II) and Cs(I), respectively. (author)

  5. Raw and renewable polymers

    CSIR Research Space (South Africa)

    Joseph, S

    2010-01-01

    Full Text Available in the permeability of the membrane and HO H3C H3C H2C H2C HO OH NH NH OH O OC C n O O O O Fig. 4 Structure of Chitin Raw and Renewable Polymers promoting internal osmotic imbalances. This results in leaching of electrolytes and proteins. 2... is often lost. In most cases this denaturation is not reversible. R-CH-COOH NH2 w Amino acid H2N COOHR a Amino acid Fig. 5 Structure of amino acid Raw and Renewable Polymers The solubilities of proteins vary considerably based on compositions...

  6. Renewable energy sources (promotion)

    International Nuclear Information System (INIS)

    Cook, F.

    1986-01-01

    Permission to present a Bill to establish an independent commission directly responsible for the research, development and demonstration of clean, renewable, alternative sources of energy (to nuclear energy) is requested. The paragraphs of the preamble to the Bill are summarized by the Member seeking permission. The main reason for promoting renewable energy sources is opposition to the nuclear industry. One objection was raised. However, permission was granted to present the Bill and it was read for the first time with a second reading ordered for 7 March 1986. The Bill itself is not reprinted but the permission and question are reported verbatim. (U.K.)

  7. Renewable Electricity Futures (Presentation)

    Energy Technology Data Exchange (ETDEWEB)

    Mai, T.

    2012-08-01

    This presentation library summarizes findings of NREL's Renewable Electricity Futures study, published in June 2012. RE Futures investigated the challenges and impacts of achieving very high renewable electricity generation levels in the contiguous United States by 2050. It was presented at the 2012 RE AMP Annual Meeting. RE-AMP is an active network of 144 nonprofits and foundations across eight Midwestern states working on climate change and energy policy with the goal of reducing global warming pollution economy-wide 80% by 2050.

  8. Coral Sr-U Thermometry

    Science.gov (United States)

    DeCarlo, T. M.; Gaetani, G. A.; Cohen, A. L.; Foster, G. L.; Alpert, A.; Stewart, J.

    2016-12-01

    Coral skeletons archive the past two millennia of climate variability in the oceans with unrivaled temporal resolution. However, extracting accurate temperature information from coral skeletons is confounded by "vital effects", which often override the temperature dependence of geochemical proxies. Here, we present a new approach to coral paleothermometry based on results of abiogenic precipitation experiments interpreted within a framework provided by a quantitative model of the coral biomineralization process. We conducted laboratory experiments to test the temperature and carbonate chemistry controls on abiogenic partitioning of Sr/Ca and U/Ca between aragonite and seawater, and we modeled the sensitivity of skeletal composition to processes occurring at the site of calcification. The model predicts that temperature can be accurately reconstructed from coral skeleton by combining Sr/Ca and U/Ca ratios into a new proxy, Sr-U. We tested the model predictions with measured Sr/Ca and U/Ca ratios of fourteen Porites sp. corals collected from the tropical Pacific Ocean and the Red Sea, with a subset also analyzed using the boron isotope (δ11B) pH proxy. Observed relationships among Sr/Ca, U/Ca, and δ11B agree with model predictions, indicating that the model accounts for the key features of the coral biomineralization process. We calibrated Sr-U to instrumental temperature records and found that it captures 93% of mean annual variability (26-30 °C) and predicts temperature within 0.5 °C (1 σ). Conversely, Sr/Ca alone has an error of prediction of 1 °C and often diverges from observed temperature by 3 °C or more. Many of the problems afflicting Sr/Ca - including offsets among neighboring corals and decouplings from temperature during coral stress events - are reconciled by Sr-U. By accounting for the influence of the coral biomineralization process, the Sr-U thermometer may offer significantly improved reliability for reconstructing ocean temperatures from coral

  9. Nontraditional renewable energy sources

    International Nuclear Information System (INIS)

    Shpil'rajn, Eh.Eh.

    1997-01-01

    The paper considers the application possibilities of nontraditional renewable energy sources to generate electricity, estimates the potential of nontraditional sources using energy of Sun, wind, biomass, as well as, geothermal energy and presents the results of economical analysis of cost of electricity generated by solar electrical power plants, geothermal and electrical plants and facilities for power reprocessing of biomass. 1 tab

  10. The wood, renewable energy

    International Nuclear Information System (INIS)

    Acket, C.

    2006-12-01

    This document evaluates the french forest situation and its future. Indeed, the wood energy constitutes in France the first renewable energy after the hydraulic. It presents the today situation of the french forest providing statistical data, evaluation of the energy estimation, the carbon fixation, the resources, the perspectives wood energy for 2050, the biofuels and an economic analysis. (A.L.B.)

  11. Information for Institutional Renewal.

    Science.gov (United States)

    Spencer, Richard L.

    1979-01-01

    Discusses a planning, management, and evaluation system, an objective-based planning process, research databases, analytical reports, and transactional data as state-of-the-art tools available to generate data which link research directly to planning for institutional renewal. (RC)

  12. Renewable Energies, Present & Future

    Institute of Scientific and Technical Information of China (English)

    X. S. Cai

    2005-01-01

    Fossil fuels are major cause of environmental destruction in pollutions. It has created much needed momentum for renewable energies, which are environmentally benign, generated locally, and can play a significant role in developing economy. As a sustainable energy sources, it can grow at a rapid pace to meet increasing demands for electricity in a cost-effective way.

  13. Renewable Energy for Microenterprise

    Energy Technology Data Exchange (ETDEWEB)

    Allderdice, A.; Rogers, J.H.

    2000-11-28

    This guide provides readers with a broad understanding of the potential benefits that current renewable energy technologies can offer rural microenterprises. It also introduces the institutional approaches that have been developed to make RE technologies accessible to microentrepreneurs and the challenges that these entrepreneurs have encountered.

  14. Renewable material resource potential

    NARCIS (Netherlands)

    van Weenen, H.; Wever, R.; Quist, J.; Tukker, A.; Woudstra, J.; Boons, F.A.A.; Beute, N.

    2010-01-01

    Renewable material resources, consist of complex systems and parts. Their sub-systems and sub-sub-systems, have unique, specific, general and common properties. The character of the use that is made of these resources, depends on the availability of knowledge, experience, methods, tools, machines

  15. Renewable Energy Essentials: Hydropower

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2010-07-01

    Hydropower is currently the most common form of renewable energy and plays an important part in global power generation. Worldwide hydropower produced 3 288 TWh, just over 16% of global electricity production in 2008, and the overall technical potential for hydropower is estimated to be more than 16 400 TWh/yr.

  16. Measurement of 90Sr in fresh water samples

    International Nuclear Information System (INIS)

    Belanova, A.; Meresova, J.; Svetlik, I.; Tomaskova, L.

    2008-01-01

    This preliminary study show new experimental approach to the determination of the radionuclide 90 Sr in water samples. The new method of dynamic windows utilizing liquid scintillation counting was applied on model and surface water samples. Our results show the demand of separation technique with significantly higher yields. (authors)

  17. Strontium (Sr) and silver (Ag) loaded nanotubular structures with combined osteoinductive and antimicrobial activities.

    Science.gov (United States)

    Cheng, Hao; Xiong, Wei; Fang, Zhong; Guan, Hanfeng; Wu, Wei; Li, Yong; Zhang, Yong; Alvarez, Mario Moisés; Gao, Biao; Huo, Kaifu; Xu, Jiangwen; Xu, Na; Zhang, Chengcheng; Fu, Jijiang; Khademhosseini, Ali; Li, Feng

    2016-02-01

    Two frequent problems are associated with the titanium surfaces of bone/dental implants: lack of native tissue integration and associated infection. These problems have prompted a significant body of research regarding the modification of these surfaces. The present study describes a hydrothermal treatment for the fabrication of strontium (Sr) and silver (Ag) loaded nanotubular structures with different tube diameters on titanium surfaces. The Sr loading from a Sr(OH)2 solution was regulated by the size of the inner diameter of the titanium nanotubes (NT) (30nm or 80nm, formed at 10V or 40V, respectively). The quantity of Ag was adjusted by immersing the samples in 1.5 or 2.0M AgNO3 solutions. Sr and Ag were released in a controllable and prolonged matter from the NT-Ag.Sr samples, with negligible cytotoxicity. Prominent antibacterial activity was observed due to the release of Ag. Sr incorporation enhanced the initial cell adhesion, migration, and proliferation of preosteoblast MC3T3-E1 cells. Sr release also up-regulated the expression of osteogenic genes and induced mineralization, as suggested by the presence of more mineralized calcium nodules in cells cultured on NT-Ag.Sr surfaces. In vivo experiments showed that the Sr-loaded samples accelerated the formation of new bone in both osteoporosis and bone defect models, as confirmed by X-ray, Micro-CT evaluation, and histomorphometric analysis of rats implanted with NT-Ag.Sr samples. The antibacterial activity and outstanding osteogenic properties of NT-Ag.Sr samples highlight their excellent potential for use in clinical applications. Two frequent problems associated with Ti surfaces, widely used in orthopedic and dental arenas, are their lack of native tissue integration and risk of infection. We describe a novel approach for the fabrication of strontium (Sr) and silver (Ag) loaded nanotubular structures on titanium surfaces. A relevant aspect of this work is the demonstration of long-lasting and controllable

  18. Renewable Substitutability Index: Maximizing Renewable Resource Use in Buildings

    Directory of Open Access Journals (Sweden)

    Ravi S. Srinivasan

    2015-05-01

    Full Text Available In order to achieve a material and energy balance in buildings that is sustainable in the long run, there is an urgent need to assess the renewable and non-renewable resources used in the manufacturing process and to progressively replace non-renewable resources with renewables. Such progressive disinvestment in the non-renewable resources that may be substituted with renewable resources is referred to as “Renewable Substitutability” and if implemented, this process will lead to a paradigm shift in the way building materials are manufactured. This paper discusses the development of a Renewable Substitutability Index (RSI that is designed to maximize the use of renewable resources in a building and quantifies the substitution process using solar emergy (i.e., the solar equivalent joules required for any item. The RSI of a building or a building component, i.e., floor or wall systems, etc., is the ratio of the renewable resources used during construction, including replacement and maintenance, to the building’s maximum renewable emergy potential. RSI values range between 0 and 1.0. A higher RSI achieves a low-energy building strategy promoting a higher order of sustainability by optimizing the use of renewables over a building’s lifetime from formation-extraction-manufacturing to maintenance, operation, demolition, and recycle.

  19. The Renewable Energy Data Explorer: Mapping Our Renewable Energy Future

    Energy Technology Data Exchange (ETDEWEB)

    2017-04-13

    The Renewable Energy (RE) Data Explorer, developed by the National Renewable Energy Laboratory, is an innovative web-based platform that allows users to visualize and analyze renewable energy potential. The RE Data Explorer informs prospecting, integrated planning, and policymaking to enable low emission development.

  20. New aragonite 87Sr/86Sr records of Mesozoic ammonoids and approach to the problem of N, O, C and Sr isotope cycles in the evolution of the Earth

    Science.gov (United States)

    Zakharov, Yuri D.; Dril, Sergei I.; Shigeta, Yasunari; Popov, Alexander M.; Baraboshkin, Eugenij Y.; Michailova, Irina A.; Safronov, Peter P.

    2018-02-01

    New Sr isotope data from well-preserved aragonite ammonoid shell material from the Mesozoic are compared with that from a living Nautilus shell. The prominent negative Sr isotope excursions known from the Middle Permian, Jurassic and Cretaceous probably have their origins in intensive plate tectonic activity, followed by enhanced hydrothermal activity at the mid-ocean ridges (mantle volcanism) which supplied low radiogenic Sr to seawater. The maximum positive (radiogenic) shift in the lower Mesozoic Sr isotope curve (Lower Triassic peak) was likely caused by a significant expansion of dry land surfaces (Dabie-Sulu Triassic orogeny) and their intensive silicate weathering in conditions of extreme warming and aridity in the very end of the Smithian, followed by warm and humid conditions in the late Spathian, which apparently resulted in a significant oceanic input of radiogenic Sr through riverine flux. The comparatively high 87Sr/86Sr ratio obtained from the living Nautilus shell is probably a function of both the Alpine orogeny, which was accompanied by significant continental weathering and input of radiogenic Sr to the oceans, and the weakening of mantle volcanism.

  1. Renewable Energy on Tribal Lands

    Science.gov (United States)

    This page contains presentations from the Brown to Green: Make the Connection to Renewable Energy workshop held in Santa Fe, New Mexico, during December 10-11, 2008 regarding Renewable Energy on Tribal Lands.

  2. Non-renewal of contracts

    CERN Multimedia

    Association du personnel

    2007-01-01

    A new illegal practice is appearing in certain sectors of the Organization: the non-renewal of renewable three-year limited-duration (LD) contracts, despite a more than satisfactory performance and an obvious commitment to the Organization.

  3. Samarium-Neodymium model age and Geochemical (Sr-Nd) signature of a bedrock inclusion from lake Vostok accretion ice.

    Science.gov (United States)

    Delmonte, B.; Petit, J. R.; Michard, A.; Basile-Doelsch, I.; Lipenkov, V.

    2003-04-01

    We investigated properties of the basal ice from Vostok ice core as well as the sediment inclusions within the accreted ice. The Vostok ice core preserves climatic information for the last 420 kyrs down to 3310m depth, but below this depth the horizontal layers of the climatic record are disrupted by the glacier dynamics. From 3450 m to 3538 m depth thin bedrock particles, as glacial flour, are entrapped. Glacial flour is released in the northern area lake, where glacier mostly melts and contributes to sediment accumulation. In the southern area, close to Vostok station, the lake water freezes and the upstream glacial flour does not contribute to sedimentation. The accreted ice contains visible sediment inclusions down to 3608 m (accretion ice 1), while below this depth and likely down to the water interface (˜3750 m), the ice is clear (accretion ice 2). The fine inclusions (1-2mm in diameter) from Accretion Ice 1 mostly consist of fine clays and quartz aggregates and we suggest they are entrained into ice as the glacier floats over shallow depth bay then it grounds against a relief rise. Afterward the glacier freely floats over the deep lake before reaching Vostok, and accreted ice 2 is clean. Sm-Nd dating of one of two inclusions at 3570 m depth gives 1.88 (+/-0.13)Ga (DM model age), corresponding to 1.47 Ga (TCHUR), suggesting a Precambrian origin. Also the isotopic signature of such inclusion (87Sr/86Sr= 0.8232 and eNd= -16) and that of a second one (87Sr/86Sr= 0.7999 and eNd= -15) are coherent with the nature of an old continental shield. Sediments that may initially accumulate in the shallow bay prior the Antarctic glaciation, should have been eroded and exported out of the lake by the glacier movement, this assuming processes for ice accretion and for sediment entrapping operate since a long time. As the glacial flour from upstream does not contribute to sedimentation, sediments need to be renewed at the surface of the bedrock rising question about the way

  4. Transesterification of soybean oil catalyzed by Sr-doped cinder

    International Nuclear Information System (INIS)

    Nasreen, Sadia; Liu, Hui; Khan, Romana; Zhu, Xiao-chan; Skala, Dejan

    2015-01-01

    Highlights: • Sr-doped cinder catalyst was prepared and used for biodiesel synthesis. • A 99% of triglycerides conversion was achieved under optimal reaction conditions. • SrAl 2 Si 2 O 8 and Sr 5 Al 8 O 1 are determined as dominant compounds which are responsible for high catalytic activity. • Catalyst exhibits high activity and can be easily recovered and regenerated. • The Sr-doped cinder catalyst is used in 14 repeated runs. - Abstract: The Strontium doped cinder was prepared using the wet impregnation method and analyzed as catalyst for biodiesel synthesis. Different procedure for cinder impregnation were investigated (temperature and duration of catalyst calcinations, the concentration of SrCl 2 solution) and optimal condition was established: impregnation 20 g of cinder 2–5 mm particles with 0.2 M SrCl 2 solution followed by calcinations at 1000 °C for 4 h. The Sr-cinder activity was tested at 90–200 °C using 1–5% mass of catalyst with different molar ratio of methanol to soybean oil (from 9 to 36). The maximum triglycerides (TG) conversion of 99.0% with the Fatty Acid Methyl Esters (FAME) yield of 97.1% was obtained by using 4% catalyst at 180 °C, for 1 h, and methanol/oil molar ratio 24:1. Influence of free fatty acid (FFA) and water in soybean oil on catalyst activity was analyzed, too. The catalyst could be used for 14 times with TG conversion and FAME yield above 90% and 80% respectively. The Sr-doped cinder catalysts before and after transesterification were characterized using BET surface area, basic strength, X-ray diffraction (XRD), scanning electron microscopy (SEM) and ICP-AAS. Results showed that the formation of SrAl 2 Si 2 O 8 and Sr 5 Al 8 O 17 complexes should be the main reason for the catalytic activity of prepared catalyst. Slow decrease of catalyst activity during its repeated use is result of Sr–Al-glycerolate formation in reaction between Sr–Al complexes and glycerol

  5. Rarotonga Sr/Ca and SST Reconstruction Data for 1726 to 1997

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — A 271 year record of Sr/Ca variability in a coral from Rarotonga in the South Pacific gyre. Calibration with monthly sea surface temperature (SST) from satellite and...

  6. LCAO calculations of SrTiO{sub 3} nanotubes

    Energy Technology Data Exchange (ETDEWEB)

    Evarestov, Robert; Bandura, Andrei, E-mail: re1973@re1973.spb.edu [Department of Quantum Chemistry, St. Petersburg State University, 26 Universitetsky Ave., 198504, Petrodvorets (Russian Federation)

    2011-06-23

    The large-scale first-principles simulation of the structure and stability of SrTiO{sub 3} nanotubes is performed for the first time using the periodic PBE0 LCAO method. The initial structures of the nanotubes have been obtained by the rolling up of the stoichiometric SrTiO{sub 3} slabs consisting of two or four alternating (001) SrO and TiO{sub 2} atomic planes. Nanotubes (NTs) with chiralities (n,0) and (n,n) have been studied. Two different NTs were constructed for each chirality: (I) with SrO outer shell, and (II) with TiO{sub 2} outer shell. Positions of all atoms have been optimized to obtain the most stable NT structure . In the majority of considered cases the inner or outer TiO{sub 2} shells of NT undergo a considerable reconstruction due to shrinkage or stretching of interatomic distances in the initial cubic perovskite structure. There were found two types of surface reconstruction: (1) breaking of Ti-O bonds with creating of Ti = O titanyl groups in outer surface; (2) inner surface folding due to Ti-O-Ti bending. Based on strain energy calculations the largest stability was found for (n,0) NTs with TiO{sub 2} outer shell.

  7. LCAO calculations of SrTiO3 nanotubes

    International Nuclear Information System (INIS)

    Evarestov, Robert; Bandura, Andrei

    2011-01-01

    The large-scale first-principles simulation of the structure and stability of SrTiO 3 nanotubes is performed for the first time using the periodic PBE0 LCAO method. The initial structures of the nanotubes have been obtained by the rolling up of the stoichiometric SrTiO 3 slabs consisting of two or four alternating (001) SrO and TiO 2 atomic planes. Nanotubes (NTs) with chiralities (n,0) and (n,n) have been studied. Two different NTs were constructed for each chirality: (I) with SrO outer shell, and (II) with TiO 2 outer shell. Positions of all atoms have been optimized to obtain the most stable NT structure . In the majority of considered cases the inner or outer TiO 2 shells of NT undergo a considerable reconstruction due to shrinkage or stretching of interatomic distances in the initial cubic perovskite structure. There were found two types of surface reconstruction: (1) breaking of Ti-O bonds with creating of Ti = O titanyl groups in outer surface; (2) inner surface folding due to Ti-O-Ti bending. Based on strain energy calculations the largest stability was found for (n,0) NTs with TiO 2 outer shell.

  8. Quantum Logic with Composite Pulse Sequences on Sr^+

    Science.gov (United States)

    Shewmon, Ruth; Labaziewicz, Jaroslaw; Ge, Yufei; Wang, Shannon; Chuang, Isaac L.

    2008-03-01

    The optical 5S1/2->4D1/2 transition in Sr^+ is an attractive qubit because it can be addressed by diode lasers, which are relatively inexpensive and easy to operate. We characterize single-qubit rotations as well as a CNOT gate on a Sr^+ ion in a surface electrode Paul trap. To improve these operations, the frequency of the clock laser is stabilized to a high-finesse optical cavity. The resulting linewidth of the laser is approximately 300Hz. Composite pulse sequences, a technique adapted from NMR, have been shown to reduce the effects of systematic errors in a variety of quantum systems. We demonstrate several composite sequences that improve the fidelity of quantum logic operations on Sr^+.

  9. Synthetic clay excels in 90Sr removal

    International Nuclear Information System (INIS)

    Komarneni, Sridhar; Kodama, Tatsuya; Paulus, William J.; Carlson, C.

    2000-01-01

    Tests with actual ground water from Hanford site, and fundamental studies of 2Na + →Sr 2+ exchange equilibria revealed that a synthetic clay is extremely selective for 90 Sr with a high capacity for uptake. Comparative studies with existing Sr selective ion exchangers clearly revealed that the present synthetic clay exhibited the best performance for 90 Sr removal from actual ground water collected from three different locations at Hanford. This novel Sr ion sieve is expected to be useful for the decontamination of the environment after accidental release and contamination with 90 Sr. (c) 2000 Materials Research Society

  10. 90Sr and 89Sr in seawater off Japan as a consequence of the Fukushima Dai-ichi nuclear accident

    Directory of Open Access Journals (Sweden)

    N. Casacuberta

    2013-06-01

    Full Text Available The impact of the earthquake and tsunami on the east coast of Japan on 11 March 2011 caused a loss of power at the Fukushima Dai-ichi nuclear power plant (NPP that resulted in one of the most important releases of artificial radioactivity into the environment. Although several works were devoted to evaluating the atmospheric dispersion of radionuclides, the impact of the discharges to the ocean has been less investigated. Here we evaluate the distribution of Fukushima-derived 90Sr (n = 57 and 89Sr (n = 19 throughout waters 30–600 km offshore in June 2011. Concentrations of 90Sr and 89Sr in both surface waters and shallow profiles ranged from 0.8 ± 0.2 to 85 ± 3 Bq m−3 and from 19 ± 6 to 265 ± 74 Bq m−3, respectively. Because of its short half-life, all measured 89Sr was due to the accident, while the 90Sr concentrations can be compared to the background levels in the Pacific Ocean of about 1.2 Bq m−3. Fukushima-derived radiostrontium was mainly detected north of Kuroshio Current, as this was acting as a southern boundary for transport. The highest activities were associated with near-shore eddies, and larger inventories were found in the closest stations to Fukushima NPP. The data evidence a major influence of direct liquid discharges of radiostrontium compared to the atmospheric deposition. Existing 137Cs data reported from the same samples allowed us to establish a 90Sr / 137Cs ratio of 0.0256 ± 0.0006 in seawater off Fukushima, being significantly different than that of the global atmospheric fallout (i.e., 0.63 and may be used in future studies to track waters coming from the east coast of Japan. Liquid discharges of 90Sr to the ocean were estimated, resulting in an inventory of 53 ± 1 TBq of 90Sr in the inshore study area in June 2011 and total releases of 90Sr ranging from 90 to 900 TBq, depending upon the reported estimates of 137Cs releases that are considered.

  11. RENEWABLE ENERGY IN TOURISM

    Directory of Open Access Journals (Sweden)

    MĂDĂLINA MIHĂILĂ

    2012-06-01

    Full Text Available Recent reports published by the International Energy Agency and U.S. Department of Energy, regarding the global energy outlook for the first three decades of the XXI century, warns of global trends on energy demand, increasing dependence on energy imports, coal use and volume emissions of greenhouse gases, torism industry being one of the biggest energy consumption industry. Uncertainties on different models of regional development and access of the world to traditional energy resources require a change of orientation towards long-term scenarios for assessing energy domain, increasing the share of energy from renewable resources beeing one of the solutions. Intourism the renewable energy is a solution for a positive impact on enviroment , reduced operational costs and even won an extra-profit.

  12. Renewables in Electricity Markets

    DEFF Research Database (Denmark)

    Ordoudis, Christos; Papakonstantinou, Athanasios; Pinson, Pierre

    2014-01-01

    Electricity is nowadays commonly exchanged through electricity markets, designed in a context where dispatchable generators, with non-negligible marginal costs, were dominating. By depending primarily on conventional (fossil, hydro and nuclear) power generation based on marginal pricing...... not designed to take into account the uncertainty brought by the substantial variability and limited predictability associated with stochastic sources, most notably wind power and solar energy. Due to these developments, the need for decision making models able to account for the uncertainty introduced by high...... from renewables, and on the adaption of electricity market designs and power system operations to the aforementioned characteristics of renewables. Additionally, the aim of the research group is supplemented by providing the appropriate frameworks for secure future investments in the field...

  13. Renewable Energy Systems

    DEFF Research Database (Denmark)

    Lund, Henrik; Mathiesen, Brian Vad; Connolly, David

    2014-01-01

    on the electricity sector, smart energy systems include the entire energy system in its approach to identifying suitable energy infrastructure designs and operation strategies. The typical smart grid sole focus on the electricity sector often leads to the conclusion that transmission lines, flexible electricity......This paper presents the learning of a series of studies that analyse the problems and perspectives of converting the present energy system into a 100 % renewable energy system using a smart energy systems approach. As opposed to, for instance, the smart grid concept, which takes a sole focus...... are to be found when the electricity sector is combined with the heating and cooling sectors and/or the transportation sector. Moreover, the combination of electricity and gas infrastructures may play an important role in the design of future renewable energy systems. The paper illustrates why electricity smart...

  14. Bolivia renewable energy development

    Energy Technology Data Exchange (ETDEWEB)

    Smith, P.

    1997-12-01

    The author summarizes changes which have occurred in Bolivia in the past year which have had an impact on renewable energy source development. Political changes have included the privatization of power generation and power distribution, and resulted in a new role for state level government and participation by the individual. A National Rural Electrification Plan was adopted in 1996, which stresses the use of GIS analysis and emphasizes factors such as off grid, economic index, population density, maintenance risk, and local organizational structure. The USAID program has chosen to stress economic development, environmental programs, and health over village power programs. The national renewables program has adopted a new development direction, with state projects, geothermal projects, and private sector involvement stressed.

  15. Renewable Energy Symposium

    International Nuclear Information System (INIS)

    2016-01-01

    Representatives of state universities, public institutions and Costa Rican private sector, and American experts have exposed projects or experiences about the use and generation of renewable energy in different fields. The thematics presented have been about: development of smart grids and design of electrical energy production systems that allow money saving and reducing emissions to the environment; studies on the use of non-traditional plants and agricultural waste; sustainable energy model in the process of coffee production; experiments from biomass for the fabrication of biodiesel, biogas production and storage; and the use of non-conventional energy. Researches were presented at the Renewable Energy Symposium, organized by the Centro de Investigacion en Estructuras Microscopicas and support of the Vicerrectoria de Investigacion, both from the Universidad de Costa Rica [es

  16. Renewable energy project development

    Energy Technology Data Exchange (ETDEWEB)

    Ohi, J.

    1996-12-31

    The author presents this paper with three main thrusts. The first is to discuss the implementation of renewable energy options in China, the second is to identify the key project development steps necessary to implement such programs, and finally is to develop recommendations in the form of key issues which must be addressed in developing such a program, and key technical assistance needs which must be addressed to make such a program practical.

  17. Renewing Samsø

    DEFF Research Database (Denmark)

    Papazu, Irina

    2017-01-01

    and globally, I ask: if indeed such a process of renewal must be understood as a political process and the island’s energy transition as an inherently political event, what can Samsø teach us about the workings of politics and local democracy as enacted in practice? This is politics not as election result...... or ideological struggle over values, ideals and the distribution of goods, but as the down-to-earth but significant activity of creating something new together....

  18. Self-renewal molecular mechanisms of colorectal cancer stem cells.

    Science.gov (United States)

    Pan, Tianhui; Xu, Jinghong; Zhu, Yongliang

    2017-01-01

    Colorectal cancer stem cells (CCSCs) represent a small fraction of the colorectal cancer cell population that possess self-renewal and multi-lineage differentiation potential and drive tumorigenicity. Self-renewal is essential for the malignant biological behaviors of colorectal cancer stem cells. While the self-renewal molecular mechanisms of colorectal cancer stem cells are not yet fully understood, the aberrant activation of signaling pathways, such as Wnt, Notch, transforming growth factor-β (TGF-β)/bone morphogenetic protein (BMP) and Hedgehog-Gli (HH-GLI), specific roles mediated by cell surface markers and micro-environmental factors are involved in the regulation of self-renewal. The elucidation of the molecular mechanisms behind self-renewal may lead to the development of novel targeted interventions for the treatment of colorectal cancer.

  19. Renewable Energy in Latvia

    Energy Technology Data Exchange (ETDEWEB)

    Shipkovs, P.; Kashkarova, G. [Latvian Energy Agency, Riga (Latvia); Shipkovs, M. [Energy-R Ltd., Riga (Latvia)

    1997-12-31

    Latvia is among those countries that do not have gas, coal and, for the time being, also oil resources of its own. The amount of power produced in Latvia does not meet the demand, consequently a part of the power has to be purchased from neighbouring countries. Firewood, peat and hydro resources are the only significant domestic energy resources. Massive decrease of energy consumption has been observed since Latvia regained independence. Domestic and renewable energy resources have been examined and estimated. There are already 13 modern boiler houses operating in Latvia with total installed capacity 45 MW that are fired with wood chips. Latvian companies are involved in the production of equipment. 7 small HPPs have been renewed with the installed capacity 1.85 MW. Wind plant in Ainazi has started its operation, where two modern wind turbines with the capacity of 0.6 MW each have been installed. Mechanism of tariff setting is aligned. Favourable power energy purchasing prices are set for renewable energy sources and small cogeneration plants

  20. Market analysis. Renewable fuels

    International Nuclear Information System (INIS)

    2014-01-01

    The Agency for Renewable Resources (FNR) had on behalf of the Federal Ministry of Food and Agriculture created a study on the market development of renewable resources in Germany and published this in the year of 2006. The aim of that study was to identify of actual status and market performance of the individual market segments of the material and energetic use as a basis for policy recommendations for accelerated and long term successful market launch and market share expansion of renewable raw materials. On behalf of the FNR, a market analysis of mid-2011 was carried out until the beginning of 2013, the results of which are hereby resubmitted. This market analysis covers all markets of material and energetic use in the global context, taking account of possible competing uses. A market segmentation, which was based on the product classification of the Federal Statistical Office, formed the basis of the analysis. A total of ten markets have been defined, seven material and three energetic use. [de

  1. Renewable Energy in Latvia

    Energy Technology Data Exchange (ETDEWEB)

    Shipkovs, P; Kashkarova, G [Latvian Energy Agency, Riga (Latvia); Shipkovs, M [Energy-R Ltd., Riga (Latvia)

    1998-12-31

    Latvia is among those countries that do not have gas, coal and, for the time being, also oil resources of its own. The amount of power produced in Latvia does not meet the demand, consequently a part of the power has to be purchased from neighbouring countries. Firewood, peat and hydro resources are the only significant domestic energy resources. Massive decrease of energy consumption has been observed since Latvia regained independence. Domestic and renewable energy resources have been examined and estimated. There are already 13 modern boiler houses operating in Latvia with total installed capacity 45 MW that are fired with wood chips. Latvian companies are involved in the production of equipment. 7 small HPPs have been renewed with the installed capacity 1.85 MW. Wind plant in Ainazi has started its operation, where two modern wind turbines with the capacity of 0.6 MW each have been installed. Mechanism of tariff setting is aligned. Favourable power energy purchasing prices are set for renewable energy sources and small cogeneration plants

  2. Internal bremsstrahlung from 89Sr and 90Sr

    International Nuclear Information System (INIS)

    Sayibaba, T.; Narasimha Murity, K.; Rao, C.R.; Satyaprakash; Gubbi, G.K.

    1987-01-01

    The internal bremsstrahlung (IB) spectra emitted in the beta-decays of 89 Sr and 90 Sr were measured with a HPGe detector and a multichannel analyser along with a standard geometrical set-up. Sufficient care has been taken to avoid spurious effects. After making all the necessary corrections, the experimental results were compared with the corresponding theoretical distributions due to Knipp and Uhlenbeck and Bloch (KUB), Lewis and Ford, Nilsson, and also due to Ford and Martin (detour theory). The total IB yields of intensity and energy from each of the isotopes in the investigated energy regions are also determined and compared with the corresponding theoretical values. The present results of IB from 89 Sr are satisfactorily accounted for by the KUB theory. In the case of 90 Sr the experimental results of IB coincide with the Coulomb-corrected theoretical distibution due to Nilsson in the energy range from 60 keV to 110 keV and Beyond 110 keV, they are found to be in excess over Nilsson's theory as well as the detour theory due to Ford and Martin up to the maximum photon energy studied, namely 350 keV

  3. What drives renewable energy development?

    International Nuclear Information System (INIS)

    Alagappan, L.; Orans, R.; Woo, C.K.

    2011-01-01

    This viewpoint reviews renewable energy development in 14 markets that differ in market structure (restructured vs. not restructured), use of feed-in-tariff (FIT) (yes vs. no), transmission planning (anticipatory vs. reactive), and transmission interconnection cost allocated to a renewable generator (high vs. low). We find that market restructuring is not a primary driver of renewable energy development. Renewable generation has the highest percent of total installed capacity in markets that use a FIT, employ anticipatory transmission planning, and have loads or end-users paying for most, if not all, of the transmission interconnection costs. In contrast, renewable developers have been less successful in markets that do not use a FIT, employ reactive transmission planning, and have generators paying for most, if not all, of the transmission interconnection costs. While these policies can lead to higher penetration of renewable energy in the short run, their high cost to ratepayers can threaten the economic sustainability of renewable energy in the long-run. - Highlights: → Market structure seems to have little effect on renewable energy development. → Renewable energy development is more successful in markets that use a FIT. → Anticipatory transmission planning aids renewable energy development. → Low interconnection costs for developers also aids renewable energy development.

  4. Renewable energy education in Turkey

    Energy Technology Data Exchange (ETDEWEB)

    Acikgoz, Caglayan [Department of Chemical and Process Engineering, Faculty of Engineering, Bilecik University, P.O.11030, Bilecik (Turkey)

    2011-02-15

    Utilization of renewable energy sources and the application of environmentally sound energy technologies are essential to sustainable development and will help to secure the quality of living and the well-being of the future generations. Turkey presently has considerable renewable energy sources. The most important renewable sources are hydropower, wind, solar, geothermal, and biomass. The use of renewable energy as a topic to study energy and its forms permits a novel way to motivate students, particularly those who energy topics taking conscience with the environment. This paper presents the analysis and classification of renewable energy sources and how to find out their origin and a way to motivate students in energy topics related to renewable sources and also, the development of didactic competencies in special blended learning arrangements for educationalists, trainers and lecturers in adult education in the field of renewable energies in Turkey. (author)

  5. Epitaxial growth and thermodynamic stability of SrIrO3/SrTiO3 heterostructures

    Science.gov (United States)

    Groenendijk, D. J.; Manca, N.; Mattoni, G.; Kootstra, L.; Gariglio, S.; Huang, Y.; van Heumen, E.; Caviglia, A. D.

    2016-07-01

    Obtaining high-quality thin films of 5d transition metal oxides is essential to explore the exotic semimetallic and topological phases predicted to arise from the combination of strong electron correlations and spin-orbit coupling. Here, we show that the transport properties of SrIrO3 thin films, grown by pulsed laser deposition, can be optimized by considering the effect of laser-induced modification of the SrIrO3 target surface. We further demonstrate that bare SrIrO3 thin films are subject to degradation in air and are highly sensitive to lithographic processing. A crystalline SrTiO3 cap layer deposited in-situ is effective in preserving the film quality, allowing us to measure metallic transport behavior in films with thicknesses down to 4 unit cells. In addition, the SrTiO3 encapsulation enables the fabrication of devices such as Hall bars without altering the film properties, allowing precise (magneto)transport measurements on micro- and nanoscale devices.

  6. Fabrication and characterization of cubic Ba{sub 0.5}Sr{sub 0.5}Co{sub 0.8}Fe{sub 0.2}O{sub 3−δ} perovskite for a novel “star-shaped” oxygen membrane with a developed surface

    Energy Technology Data Exchange (ETDEWEB)

    Borhan, Adrian Iulian [Institute of Power Engineering, Ceramic Department CEREL, Research Institute, 1 Techniczna St., 36-040 Boguchwała (Poland); Gromada, Magdalena, E-mail: gromada@cerel.pl [Institute of Power Engineering, Ceramic Department CEREL, Research Institute, 1 Techniczna St., 36-040 Boguchwała (Poland); Samoila, Petrisor [Petru Poni Institute of Macromolecular Chemistry, 41A, Gr. Ghica Voda Alley, 700487 Iasi (Romania); Gherca, Daniel [Alexandru Ioan Cuza University of Iasi, Faculty of Chemistry, 11 Carol 1 Boulevard, R-700506 Iasi (Romania)

    2016-07-15

    Highlights: • Innovative fabrication technology was elaborated for BSCF membrane with developed surface. • The tool for membranes forming with developed surface was designed and executed. • As a result of forming process, membranes with “star shape” design were obtained. • Concentration of oxygen vacancies in BSCF increases considerably with temperature. • The small polaron hopping depends on the oxygen stoichiometry deviation. - Abstract: Ba{sub 0.5}Sr{sub 0.5}Co{sub 0.8}Fe{sub 0.2}O{sub 3−δ} (BSCF), a material which can be used for the fabrication of oxygen membranes with developed surfaces, was synthesized by a solid state method. The most important material properties which have influence on the oxygen membrane usability were investigated. An innovative fabrication technology was developed for the preparation of oxygen membranes with developed surfaces by using vacuum extrusion. The tool to form membranes on a vacuum worm press was designed and executed. These allowed the formation, for the first time, of a novel “star shaped” architecture for an oxygen membrane, enabling the use of a higher effective surface for oxygen production. Comprehensive studies on structural and microstructural properties, apparent density and porosity, water absorbability, oxygen stoichiometry, thermal expansion and electrical conductivity of the BSCF membrane were performed. The results obtained demonstrated the potential application of “star-shaped” oxygen membranes in oxy-fuel combustion technology.

  7. Boosting renewable energies

    International Nuclear Information System (INIS)

    Anon.

    2010-01-01

    Public policy and funding are basically different, but both are needed to develop the renewable energy market. Public policy creates incentives, but also obligations. The setting up of a 'repurchase rate' also called a 'feed-in tariff' or 'clean energy cash back scheme' obliges electric power companies to buy back energy of renewable origin at a fixed, guaranteed rate. The extra-cost generated, although usually low, is passed on to all customers and does not cost the State anything. Funding is characterized by its source, the manner in which it is obtained and who supplies it, whether it be banks, mutual funds, development agencies, electric power companies, local governments or the consumers themselves. Repurchasing yields regular cash flows over a given period at a lower risk and allows banks to provide funding. This is one of the reasons for its success. This solution is also very popular with political leaders because it does not weigh down public funding. Both these reasons explain why repurchasing is so appreciated in Europe and in a growing number of countries, more than seventy having adopted it in 2010. In addition, it is regularly discounted in relation to technological breakthroughs and lower costs. As is the case in Europe, the problem lies in maintaining an acceptable rate while avoiding excessive project profitability. In Europe, for instance, the number of renewable energy projects is such that consumers are starting to complain about seeing their electricity rates rise because of the famous feed-in tariff, even though the cost of renewable energies continues to drop on a regular basis. The United States and a few other countries, including China, prefer the quota system, or RPS (Renewable Portfolio Standards), which requires electric power companies to generate a minimal share of electric power by a renewable energy source. These companies consequently invest in renewable energy projects or purchase this energy from other suppliers. Like the

  8. 87Sr/86Sr in gypsic soils of hyperarid settings as an altitude proxy: results for northern Chile (19-22°S) and paleoaltimetry applications

    Science.gov (United States)

    Cosentino, N. J.; Jordan, T. E.; Derry, L. A.

    2012-12-01

    Quantification of uplift of a continental surface relative to sea level is still challenging. We have developed a new altimeter based on the 87Sr/86Sr ratio of modern accumulations of salts (incipient soils) in hyperarid settings like those present in northern Chile's Atacama Desert, which lies in the forearc of the Nazca-South America plate system. The proposed altimeter is based on the first order topographic control on the extent of coastal fog. Advective events bring offshore-generated stratocumulus clouds to the continent, generating fog between 400 and 1100 m.a.s.l.. In the hyperarid desert, thin layers of calcium sulfate, among other salts, accumulate on the surface. The main sources of the calcium sulfates are i) Pacific-sourced fog that transports aerosols and dissolved salts inland, which are precipitated upon evaporation, ii) wind that transports salts derived from the weathering of Andean magmatic arc rocks, which may be recycled through salars, and to a lesser extent, iii) salts derived from volcanic emissions. While the latter two have an average 87Sr/86Sr isotopic ratio of 0.70749, the fog source has a value corresponding to seawater (0.70917). Due to the high atomic weight of Sr and to the low relative mass difference of isotopes 87Sr and 86Sr, environmental isotopic fractionation is minimal. This makes 87Sr/86Sr an excellent proxy for the primary source of the calcium sulfates and the calcium sulfates' Sr. Samples from four E-W transects of the forearc between 19.75° to 23.75° S demonstrate variations in 87Sr/86Sr for altitudes between 200 and 2700 m.a.s.l.. There is a correlation between the modern salts' 87Sr/86Sr and its altitude of formation for altitudes between ~400 and ~800 m.a.s.l., above which the 87Sr/86Sr falls abruptly until reaching values similar to or lower than the Andean average. The fact that this correlation is observed for the whole dataset (including all four transects) suggests that the relationship is regional rather than

  9. Renewable energy education for 21st century

    International Nuclear Information System (INIS)

    Charters, W.W.S.

    2000-01-01

    The major technological developments in equipment, designed to harness new and renewable sources of energy, have only taken place in the last four decades of the twentieth century, although the principles involved have been previously known for many centuries and were clearly formulated in many of the ancient civilizations. The term renewable energy (RE) itself is of relatively recent origin and only came into widespread use worldwide in the eighties, after the United Nations Conference on New and Renewable Sources of Energy, held in Nairobi, Kenya in 1981, Ref 1. Currently, the term renewable s is extensively used to describe the full range of direct and indirect uses of solar radiation incident on the earth's surface, and is often extended to include energy resources, such as tidal power or geothermal energy, neither of which is strictly renewable in the true sense of the word. Energy extracted from biomass is also generally included under this heading, although biomass is truly renewable only if continuous plantation development and replanting is carried out as the biomass is harvested. On a global scale, relatively extensive teaching about renewable energy started in the late seventies and early eighties, after the first impact of the OPEC oil price shock. Up till this time, there were only a few centres around the world where individual dedicated researchers and university teachers were involved in such activity. The next impetus to course and teaching material development came with national movements for energy independence and finally, in the latter years of this century, considerable stimulation has been given due to the increasing realisation of global environmental factors such as global warming, ozone depletion in the upper atmosphere, acid rain formation, and many other environmental degradation effects due to the increasing use of fossil fuel reserves. Considerable attention has been focused in the last twenty years through the many national and

  10. The Rb-Sr system

    International Nuclear Information System (INIS)

    Graham, I.J.

    1983-11-01

    This manual is intended to serve as a guide to the chemical procedures involved in Rb-Sr isotopic analysis as conducted at the Institute of Nuclear Sciences. Included are notes on the experimental developments made over the last 2.5 years, especially those involving rock dissolution and cation exchange chromatography

  11. 90Sr in animal bones

    International Nuclear Information System (INIS)

    Kostadinov, K.

    1994-01-01

    90 Sr content in deer from Finland and Bulgaria, as well as cows and domestic pigs from Bulgaria has been investigated. The results obtained support an evaluation of the radioactive contamination of the biosphere in Bulgaria after the Chernobyl accident. (author)

  12. Strontium isotope fractionation during strontianite (SrCO3) dissolution, precipitation and at equilibrium

    Science.gov (United States)

    Mavromatis, Vasileios; Harrison, Anna L.; Eisenhauer, Anton; Dietzel, Martin

    2017-12-01

    In this study we examine the behavior of stable Sr isotopes between strontianite [SrCO3] and reactive fluid during mineral dissolution, precipitation, and at chemical equilibrium. Experiments were performed in batch reactors at 25 °C in 0.01 M NaCl solutions wherein the pH was adjusted by bubbling of a water saturated gas phase of pure CO2 or atmospheric air. The equilibrium Sr isotope fractionation between strontianite and fluid after dissolution of the solid under 1 atm CO2 atmosphere was estimated as Δ88/86SrSrCO3-fluid = δ88/86Sr SrCO3 - δ88/86Srfluid = -0.05 ± 0.01‰. On the other hand, during strontianite precipitation, an enrichment of the fluid phase in 88Sr, the heavy isotopomer, was observed. The evolution of the δ88/86Srfluid during strontianite precipitation can be modeled using a Rayleigh distillation approach and the estimated, kinetically driven, fractionation factor αSrCO3-fluid between solid and fluid is calculated to be 0.99985 ± 0.00003 corresponding to Δ88/86SrSrCO3-fluid = -0.15‰. The obtained results further support that under chemical equilibrium conditions between solid and fluid a continuous exchange of isotopes occurs until the system approaches isotopic equilibrium. This isotopic exchange is not limited to the outer surface layer of the strontianite crystal, but extends to ∼7-8 unit cells below the crystal surface. The behavior of Sr isotopes in this study is in excellent agreement with the concept of dynamic equilibrium and it suggests that the time needed for achievement of chemical equilibrium is generally shorter compared to that for isotopic equilibrium. Thus it is suggested that in natural Sr-bearing carbonates an isotopic change may still occur close to thermodynamic equilibrium, despite no observable change in aqueous elemental concentrations. As such, a secondary and ongoing change of Sr isotope signals in carbonate minerals caused by isotopic re-equilibration with fluids has to be considered in order to use Sr

  13. Vadose Zone Infiltration Rates from Sr isotope Measurements

    Science.gov (United States)

    Maher, K.; Maher, K.; DePaolo, D. J.; DePaolo, D. J.; Conrad, M.

    2001-12-01

    Predicting infiltration rates and recharge through the vadose zone in arid regions is difficult and hence developing methods for the measurement of infiltration rates is important. We have been investigating the use of Sr isotope measurements for determining infiltration at the 200 Area plateau on the Hanford reservation in central Washington. In this context, infiltration affects the transport of contaminants to the water table as well as recharge of the groundwater system. Using Sr isotopes for this purpose requires drill core and water samples from the vadose zone, although leaches of the cores can substitute for water samples. Complementary information, including some constraints on regional recharge, can also be obtained using water samples from groundwater monitoring wells. The VZ method is based on the fact that the Sr isotope ratio of soil water just below the surface is often set by dissolution of aeolian material including carbonate, and this ratio is different from the average value in the deeper underlying vadose zone rock matrix. As water infiltrates, the Sr isotopic composition of the water changes toward the rock values as a result of Sr released from the rocks by weathering reactions. The rate of change with depth of the Sr isotope ratio of the vadose zone water is a function ultimately of q/R; the ratio of the infiltration flux (q) to the bulk rock weathering rate (R). Where it is possible to evaluate R, q can be estimated. As data accumulate it may be possible to improve the calibration of the method. At Hanford the vadose zone rock material is mostly unconsolidated sand, silt, and gravel of broadly granitic composition, which constitute the Hanford and Ringold formations. Annual precipitation is about 160 mm/yr. Drilling and coring of a ca. 70m hole to the water table in 1999 as part of the Hanford groundwater monitoring program, in a relatively undisturbed area of the site, allowed us to generate a unique Sr isotope data set. The Sr isotope

  14. Renewables 2017 Global Status Report

    International Nuclear Information System (INIS)

    Sawin, Janet L.; Sverrisson, Freyr; Seyboth, Kristin; Adib, Rana; Murdock, Hannah E.; Lins, Christine; Edwards, Isobel; Hullin, Martin; Nguyen, Linh H.; Prillianto, Satrio S.; Satzinger, Katharina; Appavou, Fabiani; Brown, Adam; Chernyakhovskiy, Ilya; Logan, Jeffrey; Milligan, Michael; Zinaman, Owen; Epp, Baerbel; Huber, Lon; Lyons, Lorcan; Nowak, Thomas; Otte, Pia; Skeen, Jonathan; Sovacool, Benjamin; Witkamp, Bert; Musolino, Evan; Brown, Adam; Williamson, Laura E.; Ashworth, Lewis; Mastny, Lisa

    2017-01-01

    Renewable energy technologies increase their hold across developing and emerging economies throughout the year The year 2016 saw several developments and ongoing trends that all have a bearing on renewable energy, including the continuation of comparatively low global fossil fuel prices; dramatic price declines of several renewable energy technologies; and a continued increase in attention to energy storage. For the third consecutive year, global energy-related carbon dioxide emissions from fossil fuels and industry were nearly flat in 2016, due largely to declining coal use worldwide but also due to improvements in energy efficiency and to increasing use of renewable energy. As of 2015, renewable energy provided an estimated 19.3% of global final energy consumption, and growth in capacity and production continued in 2016. The power sector experienced the greatest increases in renewable energy capacity in 2016, whereas the growth of renewables in the heating and cooling and transport sectors was comparatively slow. Most new renewable energy capacity is installed in developing countries, and largely in China, the single largest developer of renewable power and heat over the past eight years. In 2016, renewable energy spread to a growing number of developing and emerging economies, some of which have become important markets. For the more than 1 billion people without access to electricity, distributed renewable energy projects, especially those in rural areas far from the centralised grid, offer important and often cost-effective options to provide such access. The renewable energy sector employed 9.8 million people in 2016, an increase of 1.1% over 2015. By technology, solar PV and biofuels provided the largest numbers of jobs. Employment shifted further towards Asia, which accounted for 62% of all renewable energy jobs (not including large-scale hydropower), led by China. The development of community renewable energy projects continued in 2016, but the pace of

  15. Management of development of renewable energy sources

    Directory of Open Access Journals (Sweden)

    Inić Branimir P.

    2014-01-01

    Full Text Available The aim of the paper: 'Management of development of renewable energy sources is to point out the possible solutions for neutralizing the threat of energy shortages. The paper outlines major short and long term energy problems facing humanity. The increase of world human population is, inevitably, accompanied by higher energy consumption. Reserves decrease of nonrenewable energy sources like oil, gas, and coal is a major threat to maintaining current living conditions, and thus requires solutions in order to neutralize the threat. This is why the management of development of renewable energy sources is an imperative for Serbia. The paper emphasizes the use of solar energy, because the annual average of solar radiation in Serbia is about 40% higher than the European average, however, the actual use of the sun's energy to generate electricity in Serbia is far behind the countries of the European Union. Solar energy is clean, renewable, and the fact that 4.2 kilowatt-hours are received daily per square meter averaged over the entire surface of the planet, makes it an almost unused energy source, Compared to EU countries, the price of non-renewable derived energy is, on average, higher in Serbia. Taking this into consideration, the use of solar energy, as an unused resource, imposes itself as indispensable.

  16. Polymeric materials from renewable resources

    Energy Technology Data Exchange (ETDEWEB)

    Frollini, Elisabete; Rodrigues, Bruno V. M.; Silva, Cristina G. da; Castro, Daniele O.; Ramires, Elaine C.; Oliveira, Fernando de; Santos, Rachel P. O. [Macromolecular Materials and Lignocellulosic Fibers Group, Center for Research on Science and Technology of BioResources, Institute of Chemistry of São Carlos, University of São Paulo, CP 780, 13560-970 São Carlos, São Paulo (Brazil)

    2016-05-18

    The goals of our studies have been the use of renewable raw materials in the preparation of polymeric materials with diversified properties. In this context, lignosulfonate, which is produced in large scale around the world, but not widely used in the production of polymeric materials, was used to replace phenol and polyols in the preparation of phenolic- (Ligno-PH) and polyurethane-type (Ligno-PU) polymers, respectively. These polymers were used to prepare composites reinforced with sisal lignocellulosic fibers. The use of lignosulfonate in the formulation of both types of polymers was beneficial, because in general composites with improved properties, specially impact strength, were obtained. Composites were also prepared from the so called “biopolyethylene” (HDPE), curaua lignocellulosic fiber, and castor oil (CO). All composites HDBPE/CO/Fiber exhibited higher impact strength, when compared to those of the corresponding HDBPE/Fiber. These results, combined with others (eg SEM images of the fractured surfaces) indicated that, in addition to acting as a plasticizer, this oil may have acted as a compatibilizer of the hydrophilic fiber with the hydrophobic polymer. The set of results indicated that (i) mats with nano (diameter ≤ 100nm) and/or ultrafine (submicron scale) fibers were produced, (ii) hybrid fibers were produced (bio-based mats composites), (iii) cellulosic pulp (CP) and/or lignin (Lig) can be combined with PET matrices to control properties such as stiffness and hydrophilicity of the respective mats. Materials with diversified properties were prepared from high content of renewable raw materials, thus fulfilling the proposed targets.

  17. Polymeric materials from renewable resources

    Science.gov (United States)

    Frollini, Elisabete; Rodrigues, Bruno V. M.; da Silva, Cristina G.; Castro, Daniele O.; Ramires, Elaine C.; de Oliveira, Fernando; Santos, Rachel P. O.

    2016-05-01

    The goals of our studies have been the use of renewable raw materials in the preparation of polymeric materials with diversified properties. In this context, lignosulfonate, which is produced in large scale around the world, but not widely used in the production of polymeric materials, was used to replace phenol and polyols in the preparation of phenolic- (Ligno-PH) and polyurethane-type (Ligno-PU) polymers, respectively. These polymers were used to prepare composites reinforced with sisal lignocellulosic fibers. The use of lignosulfonate in the formulation of both types of polymers was beneficial, because in general composites with improved properties, specially impact strength, were obtained. Composites were also prepared from the so called "biopolyethylene" (HDPE), curaua lignocellulosic fiber, and castor oil (CO). All composites HDBPE/CO/Fiber exhibited higher impact strength, when compared to those of the corresponding HDBPE/Fiber. These results, combined with others (eg SEM images of the fractured surfaces) indicated that, in addition to acting as a plasticizer, this oil may have acted as a compatibilizer of the hydrophilic fiber with the hydrophobic polymer. The set of results indicated that (i) mats with nano (diameter ≤ 100nm) and/or ultrafine (submicron scale) fibers were produced, (ii) hybrid fibers were produced (bio-based mats composites), (iii) cellulosic pulp (CP) and/or lignin (Lig) can be combined with PET matrices to control properties such as stiffness and hydrophilicity of the respective mats. Materials with diversified properties were prepared from high content of renewable raw materials, thus fulfilling the proposed targets.

  18. K-Ca and Rb-Sr Dating of Lunar Granite 14321 Revisited

    Science.gov (United States)

    Simon, Justin I.; Shih, C.-Y.; Nyquist, L. E.

    2011-01-01

    K-Ca and Rb-Sr age determinations were made for a bulk feldspar-rich portion of an Apollo rock fragment of the pristine lunar granite clast (14321,1062), an acid-leached split of the sample, and the leachate. K-Ca and Rb-Sr data were also obtained for a whole rock sample of Apollo ferroan anorthosite (FAN, 15415). The recent detection [1] of widespread intermediate composition plagioclase indicates that the generation of a diversity of evolved lunar magmas maybe more common and therefore more important to our understanding of crust formation than previously believed. Our new data strengthen the K-Ca and Rb-Sr internal isochrons of the well-studied Apollo sample 14321 [2], which along with a renewed effort to study evolved lunar magmas will provide an improved understanding of the petrogenetic history of evolved rocks on the Moon.

  19. Talking Renewables; A renewable energy primer for everyone

    Science.gov (United States)

    Singh, Anirudh

    2018-03-01

    This book provides a clear and factual picture of the status of renewable energy and its capabilities today. The book covers all areas of renewable energy, starting from biomass energy and hydropower and proceeding to wind, solar and geothermal energy before ending with an overview of ocean energy. The book also explores how the technologies are being implemented today and takes a look at the future of renewable energy.

  20. Renewable energy rebound effect?: Estimating the impact of state renewable energy financial incentives on residential electricity consumption

    Science.gov (United States)

    Stephenson, Beth A.

    Climate change is a well-documented phenomenon. If left unchecked greenhouse gas emissions will continue global surface warming, likely leading to severe and irreversible impacts. Generating renewable energy has become an increasingly salient topic in energy policy as it may mitigate the impact of climate change. State renewable energy financial incentives have been in place since the mid-1970s in some states and over 40 states have adopted one or more incentives at some point since then. Using multivariate linear and fixed effects regression for the years 2002 through 2012, I estimate the relationship between state renewable energy financial incentives and residential electricity consumption, along with the associated policy implications. My hypothesis is that a renewable energy rebound effect is present; therefore, states with renewable energy financial incentives have a higher rate of residential electricity consumption. I find a renewable energy rebound effect is present in varying degrees for each model, but the results do not definitively indicate how particular incentives influence consumer behavior. States should use caution when adopting and keeping renewable energy financial incentives as this may increase consumption in the short-term. The long-term impact is unclear, making it worthwhile for policymakers to continue studying the potential for renewable energy financial incentives to alter consumer behavior.

  1. Regional Renewable Energy Cooperatives

    Science.gov (United States)

    Hazendonk, P.; Brown, M. B.; Byrne, J. M.; Harrison, T.; Mueller, R.; Peacock, K.; Usher, J.; Yalamova, R.; Kroebel, R.; Larsen, J.; McNaughton, R.

    2014-12-01

    We are building a multidisciplinary research program linking researchers in agriculture, business, earth science, engineering, humanities and social science. Our goal is to match renewable energy supply and reformed energy demands. The program will be focused on (i) understanding and modifying energy demand, (ii) design and implementation of diverse renewable energy networks. Geomatics technology will be used to map existing energy and waste flows on a neighbourhood, municipal, and regional level. Optimal sites and combinations of sites for solar and wind electrical generation (ridges, rooftops, valley walls) will be identified. Geomatics based site and grid analyses will identify best locations for energy production based on efficient production and connectivity to regional grids and transportation. Design of networks for utilization of waste streams of heat, water, animal and human waste for energy production will be investigated. Agriculture, cities and industry produce many waste streams that are not well utilized. Therefore, establishing a renewable energy resource mapping and planning program for electrical generation, waste heat and energy recovery, biomass collection, and biochar, biodiesel and syngas production is critical to regional energy optimization. Electrical storage and demand management are two priorities that will be investigated. Regional scale cooperatives may use electric vehicle batteries and innovations such as pump storage and concentrated solar molten salt heat storage for steam turbine electrical generation. Energy demand management is poorly explored in Canada and elsewhere - our homes and businesses operate on an unrestricted demand. Simple monitoring and energy demand-ranking software can easily reduce peaks demands and move lower ranked uses to non-peak periods, thereby reducing the grid size needed to meet peak demands. Peak demand strains the current energy grid capacity and often requires demand balancing projects and

  2. Introduction to renewable energy

    CERN Document Server

    Nelson, Vaughn C

    2011-01-01

    IntroductionEnergy and SocietyTypes of EnergyRenewable EnergyAdvantages/DisadvantagesEconomicsGlobal WarmingOrder of Magnitude EstimatesGrowth (Exponential)SolutionsEnergyIntroductionDefinition of Energy and PowerHeatThermodynamicsEnergy Dilemma in Light of the Laws of ThermodynamicsUse of Fossil FuelsNuclearFinite ResourceSummarySunSolar PowerElectromagnetic SpectrumEnergy Balance of the EarthEarth-Sun MotionInsolationSolar ResourceGreenhouse EffectHeat Transfer and StorageIntroductionConductionConvectionRadiationThermal MassSeasonal Heating or CoolingThermal ComfortSolar Heating and CoolingB

  3. Renewable sources of energy

    International Nuclear Information System (INIS)

    Wojas, K.

    1996-01-01

    The author takes a look at causes of the present interest in the renewable, natural sources of energy. These are: the fuel deposits becoming exhausted, hazard to environment (especially carbon dioxide) and accessibility of these sources for under-developed countries. An interrelation is shown between these sources and the energy circulations connected with atmosphere and ocean systems. The chief ones from among them that are being used now are discussed, i.e. solar radiation, wind, water waves energy, tides, geothermal heat, and the like. Problems of conversion of the forms of these kinds of energy are also given a mention. (author)

  4. Renewable Energy Country Attractiveness Indices

    International Nuclear Information System (INIS)

    2011-02-01

    Since 2003 Ernst and Young team has been releasing quarterly data that ranks national renewable energy markets, and their suitability for individual technologies. The Country Attractiveness Indices now track the relative attractiveness of 30 countries' renewable energy markets across a selection of technologies each quarter. The Renewable Energy Country Attractiveness Indices publication scores and comments on various technologies, including: on-shore wind, off-shore wind, solar PV, solar CSP, biomass, and geothermal.

  5. Policies for a renewable future

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This chapter identifies changes needed in policies regarding the utilization of renewable energy sources. The topics of the chapter include financial and legal incentives, information needs, long range energy and economic policy, environmental issues as an impetus to commercialization of renewable energy sources, taxing use of fossil fuels, encouraging renewable energy use by electric utilities through least-cost planning, educating the public and providing technical assistance, research and development, and environmental regulation and monitoring

  6. Renewable energy development in China

    Energy Technology Data Exchange (ETDEWEB)

    Junfeng, Li

    1996-12-31

    This paper presents the resources availability, technologies development and their costs of renewable energies in China and introduces the programs of renewable energies technologies development and their adaptation for rural economic development in China. As the conclusion of this paper, renewable energies technologies are suitable for some rural areas, especially in the remote areas for both household energy and business activities energy demand. The paper looks at issues involving hydropower, wind energy, biomass combustion, geothermal energy, and solar energy.

  7. Visions of regulatory renewal

    International Nuclear Information System (INIS)

    Edgeworth, A.

    1998-01-01

    The economic contribution of the CEPA (Canadian Energy Pipeline Association) member companies to Canada's trade balance was discussed. CEPA member companies transport 95 per cent of the crude oil and natural gas produced in Canada to domestic and export markets. This represents a total of 5.6 Tcf of gas annually. Half of Canada's natural gas and oil production is exported to U.S. markets. All of these exports are transported by pipeline. CEPA member companies operate 90,000 km of pipeline from British Columbia to Quebec. Expansions are needed as a result of a significant increase in demand for natural gas and crude oil since 1990. Several issues exist for regulatory renewal. They include the need to create a level playing field, the overseeing of tolls and contract renewal terms, changing risk/reward trade-offs, the right to confidentiality of information and price discovery mechanism. The drivers for regulatory reform at Westcoast Energy are the need for pricing flexibility, customers desire for toll certainty, decontracting and opposition to rolled-in expansions for gathering and processing. An overview of Westcoast Energy's negotiated toll settlement, its implications, and the components of Westcoast Energy's 'light handed regulation' (LHR) was presented

  8. Renewable Energy Marketplace

    Science.gov (United States)

    Ghadimian, Vachik

    The renewable energy sector is evolving, and today, renewable energy has become a viable alternative for many facilities. Because this sector is in its infancy stage, lack of experience has resulted in failing solar projects. This project involves the design and implementation of a functioning web application that streamlines and automates the planning, risk assessment and financing of a solar development project. The three key stakeholders, the host facility, solar installer and financier are seamlessly integrated into a single marketplace. By designing a project development workflow, projects are vetted early on and terminated if deemed infeasible, saving time and resources. By risk assessing the project using the proposed scoring model, one can inherit more confident investors. The project scoring model also serves as a debt rating system, where investors can measure the risk/rewards. The platform will also serve as a communication medium between the three stakeholders. Besides storing documents like engineering drawings, permits, etc., the platform auto-generates all necessary transactional documents, legal documents and agreements among the three stakeholders.

  9. Mexican renewable electricity law

    Energy Technology Data Exchange (ETDEWEB)

    Ruiz-Mendoza, B.J.; Sheinbaum-Pardo, C. [Institute of Engineering of the National Autonomous University of Mexico, Circuito Exterior s/n, Edificio 12 Bernardo Quintana, Piso 3, Cubiculo 319, Ciudad Universitaria, Delegacion Coyoacan, CP 04510, Mexico D.F. (Mexico)

    2010-03-15

    Two renewable electricity bills have been proposed in Congress since 2005 in Mexico. The first one was rejected by the Senate and the second one was approved by both the House of Representatives and the Senate in October 2008. Our objective is to explain the nature of both bills and to analyze each of them bearing in mind the Mexican electricity sector management scheme. In the Mexican electricity sector single-buyer scheme, the state-owned companies (Comision Federal de Electricidad and Luz y Fuerza del Centro) are responsible of the public services and the private sector generates electricity under six modalities: self-supply, cogeneration, independent production, small production, export, and import, which are not considered a public service. This scheme has caused controversies related to the constitutionality of the 1992 Power Public Services Law that allowed this scheme to be implemented. Both bills, the rejected one and the approved one, were formulated and based on that controversial law and their objectives are linked precisely more to the controversial issues than to the promotion of renewable electricity technologies; consequently, the gap among environmental, economic and social issues related with sustainability notion is wider. (author)

  10. Mexican renewable electricity law

    International Nuclear Information System (INIS)

    Ruiz-Mendoza, B.J.; Sheinbaum-Pardo, C.

    2010-01-01

    Two renewable electricity bills have been proposed in Congress since 2005 in Mexico. The first one was rejected by the Senate and the second one was approved by both the House of Representatives and the Senate in October 2008. Our objective is to explain the nature of both bills and to analyze each of them bearing in mind the Mexican electricity sector management scheme. In the Mexican electricity sector single-buyer scheme, the state-owned companies (Comision Federal de Electricidad and Luz y Fuerza del Centro) are responsible of the public services and the private sector generates electricity under six modalities: self-supply, cogeneration, independent production, small production, export, and import, which are not considered a public service. This scheme has caused controversies related to the constitutionality of the 1992 Power Public Services Law that allowed this scheme to be implemented. Both bills, the rejected one and the approved one, were formulated and based on that controversial law and their objectives are linked precisely more to the controversial issues than to the promotion of renewable electricity technologies; consequently, the gap among environmental, economic and social issues related with sustainability notion is wider. (author)

  11. Rapid method for determining Sr-89 and Sr-90 using Cherenkov and proportional counting; Schnellmethode zur Bestimmung von SR-89 und SR-90 durch Cerenkov- und Proportionalzaehlermessungen

    Energy Technology Data Exchange (ETDEWEB)

    Lange, S.; Wende, C.; Schwokowski, R.; Alisch-Mark, M.; Abraham, A.; Heinrich, T. [Staatliche Betriebsgesellschaft fuer Umwelt und Landwirtschaft, Radebeul (Germany)

    2016-07-01

    A rapid method for determining Sr-89 and Sr-90 in water, milk and biological samples has been developed and tested. After sample preparation strontium is separated by extraction chromatography using Sr resin. Eluate is divided and transfered to LSC vial and filter paper by SrCO{sub 3} precipitation. A Hidex 300 SL TDCR liquid scintillation counter and Thermo Fisher low level proportional counter have been used. Chemical yield of Sr-85 tracer is determined by Gamma spectroscopy. Uncertainty budget, decision threshold and detection limit are calculated in accordance with GUM and ISO 11929.

  12. Comments on geochemical aspects of SR 97

    International Nuclear Information System (INIS)

    Arthur, R.C.; Wei Zhou

    2000-01-01

    The Swedish Government has asked SKB to carry out a safety assessment of the KBS-3 disposal concept for spent nuclear fuel 'to demonstrate that the KBS-3 method has good prospects of being able to meet the safety and radiation protection requirements which SKI and SSI have specified in recent years.' The results of that assessment, referred to as SR 97, have recently been published. The present report summarizes the results of a review of selected geochemical aspects of SR 97. These subjects include the hydrochemical evolution of a defective canister, thermodynamic data supporting estimates of radioelement solubilities, modeling of near-field chemistry and analyses of the effects of ice melting on propagation of an oxidizing front to repository depths. The primary focus of the review is on the canister-defect scenario, and, more specifically, on supporting analyses of the hydromechanical evolution of a defective canister. The results of these analyses figure prominently in the safety assessment because they suggest that even a defective canister will, in effect, remain dry for as long as 200,000 years. This is an important constraint because it is taken in SR 97 as the period of time required for a continuous water pathway to form in the near field. The transport of most radionuclides (i.e., those that do not exist as a gas) cannot occur until this pathway is formed. It is concluded that although SKBs hydromechanical models are sound, they may suffer from an over-simplification of the chemical processes involved. Analyses using the models do not acknowledge that the chemical system within the canister is open in all respects to the chemical system in the buffer. Instead, mass transfer across the defect at the canister-buffer interface is limited to liquid H 2 O and water vapor. Consideration of mass transfer of other gases [e.g., CO 2 and H 2 S] dissolved in buffer porewaters suggests that associated reactions involving the iron insert and inner surfaces of the

  13. Renewables 2007 - Global status report

    International Nuclear Information System (INIS)

    Martinot, Eric; Mastny, Lisa; Rosbotham, Lyle; Suding, Paul; Sonntag-O'Brien, Virginia; Lempp, Philippe

    2007-01-01

    In 2007, more than $100 billion was invested in new renewable energy capacity, manufacturing plants, and research and development-a true global milestone. Yet perceptions lag behind the reality of renewable energy because change has been so rapid in recent years. This report captures that reality and provides an overview of the status of renewable energy worldwide in 2007. The report covers trends in markets, investments, industries, policies, and rural (off-grid) renewable energy. (By design, the report does not provide analysis, discuss current issues, or forecast the future.) Many of the trends reflect increasing significance relative to conventional energy

  14. Integrating Renewables in Electricity Markets

    DEFF Research Database (Denmark)

    Morales González, Juan Miguel; Conejo, Antonio J.; Madsen, Henrik

    in the electricity market. • The development of procedures to enable demand response and to facilitate the integration of stochastic renewable units. This book is written in a modular and tutorial manner and includes many illustrative examples to facilitate its comprehension. It is intended for advanced...... such as: • The modeling and forecasting of stochastic renewable power production. • The characterization of the impact of renewable production on market outcomes. • The clearing of electricity markets with high penetration of stochastic renewable units. • The development of mechanisms to counteract...

  15. Economics of nuclear and renewables

    International Nuclear Information System (INIS)

    Khatib, Hisham; Difiglio, Carmine

    2016-01-01

    This paper provides an assessment of the economic challenges faced by both nuclear power and “new” renewable electricity technologies. The assessment reflects the need to incorporate new renewables into power grids and issues faced in dispatching power and their effect on traditional electricity technologies as well as the need for transmission extension and/or grid reinforcement. Wider introduction of smart grids and the likely demise of nuclear in some OECD countries are bound to enhance the future prospects for new renewables. However, their immediate future expansion will depend on continued subsidies, which are becoming difficult to sustain in present economic circumstances. Development of large energy storage facilities and carbon pricing could significantly enhance future renewable energy prospects. Correspondingly, expanding renewable energy, in spite of their popularity with some governments and sections of the public, is likely to face challenges which will slow their present rapid progress. Nuclear is now shied away from in many industrialized countries and having mixed prospects in developing economies. In many instances, it suffers from high initial costs, long lead times and often excessive construction delays. Nuclear power also faces challenging risks – investment as well as regulatory. In contrast to renewables, its share of global energy consumption is declining. - Highlights: •Renewables are increasing their energy share. •Renewables system cost is higher than their production cost. •Nuclear share is not increasing and their costs are not reduced. •Discount rate and subsidies are important in economics of renewables and nuclear.

  16. Regulatory guidance for license renewal

    International Nuclear Information System (INIS)

    Thoma, John A.

    1991-01-01

    The proposed 10 CFR Part 54 rule proceduralizes the process for license renewal by identifying both the administrative and technical requirements for a renewal application. To amplify and support this regulation, written guidance has been provided in the form of a draft Regulatory Guide (DG 1009) and a draft Standard Review Plan for License Renewal (NUREG 1299). This guidance is scheduled to be finalized in 1992. Similar guidance will be provided for the proposed revisions to 10 CFR Part 51 concerning the environmental aspects of license renewal. (author)

  17. Renewable Acrylonitrile Production

    Energy Technology Data Exchange (ETDEWEB)

    Beckham, Gregg T [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Karp, Eric M [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Eaton, Todd R [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Sanchez i Nogue, Violeta [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Vorotnikov, Vassili [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Biddy, Mary J [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Tan, Eric C [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Brandner, David [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Manker, Lorenz [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Michener, William E [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Vardon, Derek R [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Bratis, Adam D [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Liu, Rongming [University of Colorado; Gill, Ryan T. [University of Colorado; Gilhespy, Michelle [Johnson Matthey Technology Centre; Skoufa, Zinovia [Johnson Matthey Technology Centre; Watson, Michael J. [Johnson Matthey Technology Centre; Fruchey, O. Stanley [MATRIC; Cywar, Robin M. [Formerly NREL

    2017-12-08

    Acrylonitrile (ACN) is a petroleum-derived compound used in resins, polymers, acrylics, and carbon fiber. We present a process for renewable ACN production using 3-hydroxypropionic acid (3-HP), which can be produced microbially from sugars. The process achieves ACN molar yields exceeding 90% from ethyl 3-hydroxypropanoate (ethyl 3-HP) via dehydration and nitrilation with ammonia over an inexpensive titanium dioxide solid acid catalyst. We further describe an integrated process modeled at scale that is based on this chemistry and achieves near-quantitative ACN yields (98 +/- 2%) from ethyl acrylate. This endothermic approach eliminates runaway reaction hazards and achieves higher yields than the standard propylene ammoxidation process. Avoidance of hydrogen cyanide as a by-product also improves process safety and mitigates product handling requirements.

  18. Rewards of renewables

    Science.gov (United States)

    McNamee, Gregory

    2008-09-01

    In 1987 an American-style fridge freezer would use about 950 kWh of electricity and cost about 150 (£80) a year to run. Two decades on, a comparable appliance uses half the electricity and costs less than half as much to run. In 1975 there were about 3780 000 cars on the streets of Los Angeles, whereas today there are more than 5200 000 - yet air-pollution levels have fallen by half and an increasing number of those vehicles are hybrids or rely on renewable fuels like bio-diesel. Last year, half a million homes in Southern California were receiving direct solar power, either from solar electricity plants or from rooftop photovoltaic panels.

  19. Marine Renewable Energy Seascape

    Directory of Open Access Journals (Sweden)

    Alistair G.L. Borthwick

    2016-03-01

    Full Text Available Energy production based on fossil fuel reserves is largely responsible for carbon emissions, and hence global warming. The planet needs concerted action to reduce fossil fuel usage and to implement carbon mitigation measures. Ocean energy has huge potential, but there are major interdisciplinary problems to be overcome regarding technology, cost reduction, investment, environmental impact, governance, and so forth. This article briefly reviews ocean energy production from offshore wind, tidal stream, ocean current, tidal range, wave, thermal, salinity gradients, and biomass sources. Future areas of research and development are outlined that could make exploitation of the marine renewable energy (MRE seascape a viable proposition; these areas include energy storage, advanced materials, robotics, and informatics. The article concludes with a sustainability perspective on the MRE seascape encompassing ethics, legislation, the regulatory environment, governance and consenting, economic, social, and environmental constraints. A new generation of engineers is needed with the ingenuity and spirit of adventure to meet the global challenge posed by MRE.

  20. Resources: the renewable promises

    International Nuclear Information System (INIS)

    Bellin, I.; Damier, J.; Persiaux, R.

    2010-01-01

    A set of brief articles gives an overview of development perspectives and objectives for renewable energies in France (biomass, hydraulic, wind, geothermal, solar, and sea energies). The influence of public investments and subsidies, and possible technological developments are evoked for solar energy. The advances of various projects and ideas in the field of sea energy are discussed: sea current energy, wave and swell energy, offshore wind generators, ocean thermal energy. The objectives and impacts of the use of biomass and of the development of bio-refineries are discussed, as well as the challenge CO 2 capture and storage. The evolution of electricity networks is outlined in terms of electricity storage, demand management and energy saving

  1. Renewable Energy Certificate Program

    Energy Technology Data Exchange (ETDEWEB)

    Gwendolyn S. Andersen

    2012-07-17

    This project was primarily to develop and implement a curriculum which will train undergraduate and graduate students at the University seeking a degree as well as training for enrollees in a special certification program to prepare individuals to be employed in a broad range of occupations in the field of renewable energy and energy conservation. Curriculum development was by teams of Saint Francis University Faculty in the Business Administration and Science Departments and industry experts. Students seeking undergraduate and graduate degrees are able to enroll in courses offered within these departments which will combine theory and hands-on training in the various elements of wind power development. For example, the business department curriculum areas include economic modeling, finance, contracting, etc. The science areas include meteorology, energy conversion and projection, species identification, habitat protection, field data collection and analysis, etc.

  2. Participatory urban renewal

    Directory of Open Access Journals (Sweden)

    Drago Kos

    2005-01-01

    Full Text Available The article consists of two parts. The first deals with the theoretical framework of urban rehabilitation. Literature provides the basis for a conclusion, which is that the key issue in rehabilitation projects is legitimate negotiation of various interests between participating individuals and institutions. In the second part this presentation and analyses of events that took place at the urban design workshop organised within the framework of the research project Renewal of housing estates in Ljubljana, provide experiential confirmation of the starting thesis. We established that the directly involved residents were willing to actively participate in rehabilitation procedures, however the process is never triggered, because of insufficient capacities in institutional frameworks. In conclusion several real proposals are shown, namely, how to surmount obstacles in urban rehabilitation and especially in larger housing estates built after World War 2.

  3. Renewal of radiological equipment.

    Science.gov (United States)

    2014-10-01

    In this century, medical imaging is at the heart of medical practice. Besides providing fast and accurate diagnosis, advances in radiology equipment offer new and previously non-existing options for treatment guidance with quite low morbidity, resulting in the improvement of health outcomes and quality of life for the patients. Although rapid technological development created new medical imaging modalities and methods, the same progress speed resulted in accelerated technical and functional obsolescence of the same medical imaging equipment, consequently creating a need for renewal. Older equipment has a high risk of failures and breakdowns, which might cause delays in diagnosis and treatment of the patient, and safety problems both for the patient and the medical staff. The European Society of Radiology is promoting the use of up-to-date equipment, especially in the context of the EuroSafe Imaging Campaign, as the use of up-to-date equipment will improve quality and safety in medical imaging. Every healthcare institution or authority should have a plan for medical imaging equipment upgrade or renewal. This plan should look forward a minimum of 5 years, with annual updates. Teaching points • Radiological equipment has a definite life cycle span, resulting in unavoidable breakdown and decrease or loss of image quality which renders equipment useless after a certain time period.• Equipment older than 10 years is no longer state-of-the art equipment and replacement is essential. Operating costs of older equipment will be high when compared with new equipment, and sometimes maintenance will be impossible if no spare parts are available.• Older equipment has a high risk of failure and breakdown, causing delays in diagnosis and treatment of the patient and safety problems both for the patient and the medical staff.• Every healthcare institution or authority should have a plan for medical imaging equipment upgrade or replacement. This plan should look forward a

  4. Preparation of thin layers of BiSrCaCuO by method MOCVD

    International Nuclear Information System (INIS)

    Beran, P.; Stejskal, J.; Strejc, A.; Nevriva, M.; Sedmibudsky, D.; Leitner, J.

    1999-01-01

    Preparation of superconducting material on the basis mixed oxides of BiSrCaCuO by chemical vapour deposition (CVD) method is described. Surface morphology and concentration profiles of elements were analyzed by scanning electron microscope and microprobe. Phase of layers was analysed by X-ray diffraction (radiation of Cu kα ). Samples of thin layers were characterized by magnetic susceptibility in temperature interval 10 to 150 K. Obtained results confirm formation of superconducting phases Bi 2 Sr 2 Ca 1 Cu 2 O x and Bi 2 Sr 2 Xa 2 Cu 3 O x

  5. A Preliminary study of Sr/Ca thermometry in Chang Islands, Gulf of Thailand

    Directory of Open Access Journals (Sweden)

    Wararat Sirianansakul

    2014-10-01

    Full Text Available Variations in ratios of strontium-to-calcium (Sr/Ca for two Porites sp. coral specimens collected from Wai (PW and Loa Ya (PLY islands, part of Chang islands, Gulf of Thailand, were determined. Inductively coupled plasma optimal emission spectrometry (ICP-OES was used to analyze this ratio, which demonstrates annual cycles and the data is assumed to reflect the sea surface temperature (SST. Comparing the ratios with SST data, following Sr/Ca–SST relationships were determined PW: Sr/Ca (mmol/mol = 11.56–0.070×SST, PLY: Sr/Ca (mmol/mol = 11.89–0.081×SST. Our correlations are different from those previously reported; a discrepancy that may involve differences in analytical methods employed and abnormally low sea surface salinity (SSS (<30 psu in the Gulf of Thailand.

  6. Renewable Energy in European Regions

    NARCIS (Netherlands)

    Krozer, Yoram

    2012-01-01

    The regional dynamics of energy innovation, in particular the shift from fossil fuels to renewable energy in the EU, is discussed within the framework of neo-Schumpeterian theory. The EU’s 4.2% average annual growth in renewable energy production in the last decade has been accompanied by diverging

  7. Business development in renewable energy

    NARCIS (Netherlands)

    Krozer, Yoram; Visa, Ion

    2014-01-01

    This paper discusses how to foster development of renewable energy business. Factors that impede or enhance renewable energy in the EU 27 member states in the period 1998–2008 are analyzed. Nine factors are considered: population density, production output and energy sector output to indicate market

  8. PYRAMID LAKE RENEWEABLE ENERGY PLAN

    Energy Technology Data Exchange (ETDEWEB)

    HIGH DESERT GEOCULTURE, LLC

    2009-06-06

    The Pyramid Lake Renewable Energy Plan covers these areas: energy potential (primarily focusing on geothermal resource potential, but also more generally addressing wind energy potential); renewable energy market potential; transmission system development; geothermal direct use potential; and business structures to accomplish the development objectives of the Pyramid Lake Paiute Tribe.

  9. Renewal Processes and Repairable Systems

    NARCIS (Netherlands)

    2003-01-01

    In this thesis we discuss the following topics: 1. Renewal reward processes The marginal distributions of renewal reward processes and its version, which we call in this thesis instantaneous reward processes, are derived. Our approach is based on the theory of point processes, especially Poisson

  10. Renewable energies: public policy challenges

    International Nuclear Information System (INIS)

    Grazi, Laure; Souletie, Arthur

    2016-03-01

    Renewable energy sources (RES) are low-carbon energies available right within our borders, and as such can be of great value in addressing the challenges of climate change and energy security. In 2014, renewable energies accounted for 14.6% of France's gross final energy consumption. The French Energy Transition Act for Green Growth sets renewables targets of 23% and 32% as a share of gross final energy consumption by 2020 and 2030, respectively. However, renewable energies are still more costly than conventional energies. A significant share of this additional cost is borne by energy consumers, particularly in the form of energy taxation and biofuels blending obligations. Public aid is also provided to support heat production from renewable energy sources (RES-H). The two most significant aids available today are the Energy Transition Tax Credit (CITE) and the Heat Fund. Comparing the various types of renewable energies shows sharp disparities in terms of the cost of avoiding one tonne of CO 2 , which ranges from euros 59 to more than euros 500 for electricity production it follows that the cost of the energy transition is likely to vary significantly depending on which renewable energy sources are pushed to the fore. The combustion of biomass for heat production appears to offer an economically efficient way to reduce CO 2 emissions. Of the various renewable technologies available for the production of electricity (with the exception of hydropower, which was excluded from the scope of this study), onshore wind power is the least costly

  11. Renewable Energy Education in India

    Science.gov (United States)

    Bajpai, Shrish; Kidwai, Naimur Rahman

    2017-01-01

    The issue of renewable energy sources that have great potential to give solutions to the longstanding energy problems of India has been considered. It has been stated that renewable energy sources are an important part of India's plan to increase energy security and provide new generation with ample job opportunities. India's plans to move towards…

  12. 75 FR 26919 - Charter Renewals

    Science.gov (United States)

    2010-05-13

    ...: Notice of Renewal of the Advisory Committee on Commercial Remote Sensing Charter. SUMMARY: In accordance... Commercial Remote Sensing (ACCRES) is in the public interest in connection with the performance of duties imposed on the Department by law. The ACCRES Charter was renewed on April 1, 2010. SUPPLEMENTARY...

  13. Constricted double loop hysteresis and exchange bias attributed to the surface anisotropy in nanocrystalline La1/3Sr2/3Fe1−xCrxO3

    International Nuclear Information System (INIS)

    Sabyasachi, Sk.; Patra, M.; Majumdar, S.; Giri, S.

    2013-01-01

    We investigate magnetic properties of nanocrystalline ferrites with composition La 1/3 Sr 2/3 Fe 1−x Cr x O 3 (LSFCO) for x=0, 0.02, 0.04 and 0.06. Thermal variation of zero field cooled magnetization displays a weak signature close to the charge (T CO ) as well as antiferromagnetic ordering for x=0, 0.02 and 0.04. In addition, another disordered glassy magnetic transition (T g ) is noticed for all the compositions. T g is predominantly observed, although signature of charge ordering almost disappears for x=0.06. Interestingly, a constricted double loop type magnetic hysteresis loop is observed for x=0.02. This structure in the hysteresis loop disappears with further increase in Cr substitution. A systematic shift in the magnetic hysteresis loop is observed for all the compositions, while samples are cooled in a static magnetic field, which is the manifestation of exchange bias (EB) effect. The EB field (H E ) and magnetization (M E ) decrease remarkably due to minor Cr substitution at x=0.02 and then it reveals a sluggish increase with increasing x. For x=0.04 the EB effect emerges below ∼T CO , increases sluggishly with lowering of temperature and below ∼T g , it increases rapidly. The cooling field dependence exhibits significant increase of H E and M E for x=0.04, which is associated with the considerable increase of coercivity. Possible origin of EB correlated with the magnetic phase coexistence has been argued for nanocrystalline LSFCO. - Highlights: • Constricted double loop structure is observed for minor Cr substitution. • Exchange bias decreases significantly due to Cr substitution. • Intricate magnetic phase coexistence leads to the exchange bias effect

  14. Experimental probe into adsorption of Sr, Cs in the Soil

    International Nuclear Information System (INIS)

    Yuan Guangyu; Bai Qingzhong

    1987-12-01

    There are some obstacles in researching on the adsorption patterns of Sr and Cs in soil. One of them is that it is difficult to compare and to consult between various results and data for different types and sizes of soil. For this reason, it is neccesary to do further research into adsorption patterns of Sr and Cs in single particles of soil. By using scanning electromicroscope, the microcosmic phenomena of nuclides adsorption is observed, and a possible mechanism is proposed. A certain amount of diluvial soil from Shanxi Province and a certain amount of alluvial soil from western Beijing suburban were chosen as detected samples. After determining the distributions of adsorbed Sr and Cs in varied mineral particles, it is pointed out that the defference of chemical components of various size soils effects Kd value of Sr and Cs obviously. The method for calculating Kd value of mixing samples according to the particle distribution coefficients are derived under the condition of surface adsorption as main. The authors expound that it is favourable for accuracy to select and control the particle sizes in static adsorptional experiment

  15. Renewables in Global Energy Supply

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2007-07-01

    Renewable energies are essential contributors to the energy supply portfolio as they contribute to world energy supply security, reducing dependency on fossil fuel resources, and provide opportunities for mitigating greenhouse gases. Differences in definition and lack of adequate data complicated the discussion between participants on these key issues. The International Energy Agency believes that this fact sheet can be of use to all to facilitate the debate on the past, current and future place and role of renewables in total energy supply. Our goal is to present as objectively as possible the main elements of the current renewables energy situation. The definitions and coverage of national statistics vary between countries and organisations. In this fact sheet, the renewables definition includes combustible renewables and waste (CRW), hydro, geothermal, solar, wind, tide and wave energy.

  16. New renewables - a business challenge

    International Nuclear Information System (INIS)

    Jochum, G.

    2004-01-01

    This article takes a look at the increased use of renewable forms of energy and, in particular, the so-called 'new renewables' that are the subject of discussion in Europe and Switzerland. The wide divergence between the political and economical viewpoints concerning renewables is examined and the question is posed on how political desires and economical sense can be brought closer together. Questions concerning the public acceptance of various forms of energy are looked at and the expectations placed on renewable forms of energy are commented on. Criteria for models of promotion are listed including CO 2 emissions, technology and cost efficiency, marketing aspects and flexibility. Also, aspects concerning plausibility, fairness and responsibility are looked at. A model named 'Swiss Renewables Model' is proposed and its efficiency, functionality and financing are discussed

  17. The potential of renewable energies

    International Nuclear Information System (INIS)

    Glubrecht, H.

    1998-01-01

    If one compares the progress in research and development of renewable energy applications with the finding which has been granted to these activities during the 23 years after the first oil shock, one cannot but be very impressed. It is indicated in this paper hoe comprehensive the potential of renewable energy is. One should take into account that the methods described form a broad interdisciplinary field in contrast to fossil and nuclear technologies. From technical point of view the present and future energy demand can be met by the broad spectrum of renewable energies in combination with energy conservation. Many of these techniques are already economically competitive: solar architecture, wind energy, hydropower, low temperature heat production, photovoltaic for remote areas, various types of biomass application, geothermal energy although not exactly renewable. The future of renewable energies will depend on opening markets for these techniques

  18. Somerset County Renewable Energy Initiative

    Energy Technology Data Exchange (ETDEWEB)

    Katula, Denise [County of Somerset, Somervile, NJ (United States)

    2014-05-07

    The County of Somerset, New Jersey, through the Somerset County Improvement Authority (SCIA), applied Federal funding through the U.S. Department of Energy to will apply project funds to buy-down the capital costs of equipment associated with the installation of solar photovoltaic (PV) systems at two sites owned by the County. This Renewable Energy Initiative allows the County to take advantage of clean renewable energy, without any adverse debt impacts, and at a price that results in operating budget savings beyond what is presently available in the marketplace. This project addressed the objectives of the Office of Energy Efficiency and Renewable Energy by making the acquisition of renewable energy more affordable for the County, thereby, encouraging other counties and local units to develop similar programs and increase the deployment of solar energy technologies. The two sites that were funded by the DOE grant are part of a much larger, ambitious, and unique renewable energy project, described in the next section.

  19. Renewal-anomalous-heterogeneous files

    International Nuclear Information System (INIS)

    Flomenbom, Ophir

    2010-01-01

    Renewal-anomalous-heterogeneous files are solved. A simple file is made of Brownian hard spheres that diffuse stochastically in an effective 1D channel. Generally, Brownian files are heterogeneous: the spheres' diffusion coefficients are distributed and the initial spheres' density is non-uniform. In renewal-anomalous files, the distribution of waiting times for individual jumps is not exponential as in Brownian files, yet obeys: ψ α (t)∼t -1-α , 0 2 >, obeys, 2 >∼ 2 > nrml α , where 2 > nrml is the MSD in the corresponding Brownian file. This scaling is an outcome of an exact relation (derived here) connecting probability density functions of Brownian files and renewal-anomalous files. It is also shown that non-renewal-anomalous files are slower than the corresponding renewal ones.

  20. Modeling renewable energy company risk

    International Nuclear Information System (INIS)

    Sadorsky, Perry

    2012-01-01

    The renewable energy sector is one of the fastest growing components of the energy industry and along with this increased demand for renewable energy there has been an increase in investing and financing activities. The tradeoff between risk and return in the renewable energy sector is, however, precarious. Renewable energy companies are often among the riskiest types of companies to invest in and for this reason it is necessary to have a good understanding of the risk factors. This paper uses a variable beta model to investigate the determinants of renewable energy company risk. The empirical results show that company sales growth has a negative impact on company risk while oil price increases have a positive impact on company risk. When oil price returns are positive and moderate, increases in sales growth can offset the impact of oil price returns and this leads to lower systematic risk.

  1. Renewable energies for power generation

    International Nuclear Information System (INIS)

    Freris, L.; Infield, D.

    2009-01-01

    Power generation from renewable energy sources is different from power generation from classical energies (nuclear, thermal..). Therefore, the integration into the grid of the electricity supplied by renewable sources requires a deep thinking. The reason is that these power sources are controlled by variable elements, like wind, water and sun, which condition production. This book deals with the following aspects in detail: characteristics of classical and intermittent generators; grid balancing between supply and demand; conversion methods of renewable energies into electricity; power systems; privatizing of power generation and birth of new markets, in particular the 'green' power market; development of renewable energies thanks to technical advances. It gives a comprehensive overview of the present day available renewable energy sources for power generation. (J.S.)

  2. Electrochemical Approaches to Renewable Energy

    Science.gov (United States)

    Lobaccaro, Peter

    Renewable energy is becoming an increasingly important component of the world's energy supply as the threat of global warming continues to rise. There is a need to reduce the cost of this renewable energy and a future challenge to deal with the strain intermittent power sources like renewables place on the power grid. In this dissertation, electrochemistry is harnessed to address possible solutions to both of these issues. First, it is used to develop a low cost alternative photovoltaic material. Then, it is used to investigate the production of chemical fuel stocks which can be used for energy storage. In chapter 2, advances are made in the electrochemical deposition of indium (In) on molybdenum foil which enables the deposition of electronic-grade purity, continuous films with thicknesses in the micron range. As an example application, the electrodeposited In films are phosphorized via the thin-film vapor-liquid-solid growth method. The resulting poly-crystalline InP films display excellent optoelectronic quality, comparable to films grown from more standard vacuum deposition techniques. This demonstrates the versatility of the developed electrochemical deposition procedure. In the remaining chapters, renewable fuel production is investigated. First in chapter 3, molybdenum disulfide (MoS2) is examined as a catalyst for the hydrogen evolution reaction (HER). Typically, high-cost synthesized MoS2 is used as the catalyst because the pristine MoS 2 mineral is known to be a poor catalyst. The fundamental challenge with pristine MoS2 is the inert HER activity of the predominant (0001) basal surface plane. Here, we report a general thermal process in which the basal plane is texturized to increase the density of HER-active edge sites. The process generates high HER catalytic performance in pristine MoS 2 across various morphologies such as the bulk mineral, films composed of micron-scale flakes, and even films of a commercially-available spray of nanoflake MoS2. In

  3. Polymer biocomposites with renewable sources

    Directory of Open Access Journals (Sweden)

    S. Kuciel

    2010-07-01

    Full Text Available Nowadays production of natural biodegradable polymer composites is an important research topic on the stage of renewable sourcesimplementation instead of petrochemical sources. In this work, possibilities of processing biocomposites on the base on different types of biopolymers – polylactide (PLA, thermoplastic starch (TPS, polyhydroxybutyrate (PHB, cellulose acetate (CA - filled with natural fibers such as wood, kenaf, horse hair and nettle are presented. Large variety of natural fibers and their developed surface which increases adhesion to matrix makes them an attractive filler material. The fibers serve as reinforcement by giving strength and stiffness to the structure while the polymer matrix holds the fibers in place so that suitable structural composites can be made. Main physic-mechanical properties of natural fibers and biopolymers are presented. Modulus of elasticity and tensile strength increased with rising content of natural fibers in composite. The results show that biocomposites based on starch or PHB filled with kenaf fibers has the best mechanical properties. Modulus of elasticity achieves 10-12 GPa and tensile strength 50 MPa. This property can be interesting for packaging especially for fresh food like fruits or vegetables and for technical products with short-time life cycles. In future prospects, biocomposites based on biopolymers with a long time of decomposition can be interesting alternative as a construction material in automotive sectors.

  4. The influence of SrO and CaO in silicate and phosphate bioactive glasses on human gingival fibroblasts.

    Science.gov (United States)

    Massera, J; Kokkari, A; Närhi, T; Hupa, L

    2015-06-01

    In this paper, we investigate the effect of substituting SrO for CaO in silicate and phosphate bioactive glasses on the human gingival fibroblast activity. In both materials the presence of SrO led to the formation of a CaP layer with partial Sr substitution for Ca. The layer at the surface of the silicate glass consisted of HAP whereas at the phosphate glasses it was close to the DCPD composition. In silicate glasses, SrO gave a faster initial dissolution and a thinner reaction layer probably allowing for a continuous ion release into the solution. In phosphate glasses, SrO decreased the dissolution process and gave a more strongly bonded reaction layer. Overall, the SrO-containing silicate glass led to a slight enhancement in the activity of the gingival fibroblasts cells when compared to the SrO-free reference glass, S53P4. The cell activity decreased up to 3 days of culturing for all phosphate glasses containing SrO. Whereas culturing together with the SrO-free phosphate glass led to complete cell death at 7 days. The glasses containing SrO showed rapid cell proliferation and growth between 7 and 14 days, reaching similar activity than glass S53P4. The addition of SrO in both silicate and phosphate glasses was assumed beneficial for proliferation and growth of human gingival fibroblasts due to Sr incorporation in the reaction layer at the glass surface and released in the cell culture medium.

  5. Bioactive SrO-SiO2 glass with well-ordered mesopores: characterization, physiochemistry and biological properties.

    Science.gov (United States)

    Wu, Chengtie; Fan, Wei; Gelinsky, Michael; Xiao, Yin; Simon, Paul; Schulze, Renate; Doert, Thomas; Luo, Yongxiang; Cuniberti, Gianaurelio

    2011-04-01

    For a biomaterial to be considered suitable for bone repair it should ideally be both bioactive and have a capacity for controllable drug delivery; as such, mesoporous SiO(2) glass has been proposed as a new class of bone regeneration material by virtue of its high drug-loading ability and generally good biocompatibility. It does, however, have less than optimum bioactivity and controllable drug delivery properties. In this study, we incorporated strontium (Sr) into mesoporous SiO(2) in an effort to develop a bioactive mesoporous SrO-SiO(2) (Sr-Si) glass with the capacity to deliver Sr(2+) ions, as well as a drug, at a controlled rate, thereby producing a material better suited for bone repair. The effects of Sr(2+) on the structure, physiochemistry, drug delivery and biological properties of mesoporous Sr-Si glass were investigated. The prepared mesoporous Sr-Si glass was found to have an excellent release profile of bioactive Sr(2+) ions and dexamethasone, and the incorporation of Sr(2+) improved structural properties, such as mesopore size, pore volume and specific surface area, as well as rate of dissolution and protein adsorption. The mesoporous Sr-Si glass had no cytotoxic effects and its release of Sr(2+) and SiO(4)(4-) ions enhanced alkaline phosphatase activity - a marker of osteogenic cell differentiation - in human bone mesenchymal stem cells. Mesoporous Sr-Si glasses can be prepared to porous scaffolds which show a more sustained drug release. This study suggests that incorporating Sr(2+) into mesoporous SiO(2) glass produces a material with a more optimal drug delivery profile coupled with improved bioactivity, making it an excellent material for bone repair applications. Copyright © 2010 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

  6. Capital renewal as a real option

    NARCIS (Netherlands)

    Reindorp, M.J.; Fu, M.C.

    2011-01-01

    We consider the timing of replacement of obsolete subsystems within an extensive, complex infrastructure. Such replacement action, known as capital renewal, must balance uncertainty about future profitability against uncertainty about future renewal costs. Treating renewal investments as real

  7. Battery storage for supplementing renewable energy systems

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2009-01-18

    The battery storage for renewable energy systems section of the Renewable Energy Technology Characterizations describes structures and models to support the technical and economic status of emerging renewable energy options for electricity supply.

  8. Building a sustainable market for renewables

    Energy Technology Data Exchange (ETDEWEB)

    Rader, N.

    1996-12-31

    Opinions regarding marketing approaches for electricity generation from renewable resources are presented in the paper. The Renewables Portfolio Standard of the California Public Utilities Commission is described. This system is based on renewable energy credits. Other marketing approaches, including surcharges, auctioned renewables credit, green pricing, and green marketing are also assessed. It is concluded that the Renewables Portfolio Standard creates a stable economic environment for the renewable energy industries.

  9. Rapid determination of 90Sr in seawater

    International Nuclear Information System (INIS)

    Pavlotskaya, F.I.; Moskin, A.I.

    1994-01-01

    A method for determining 90 Sr in seawater that is based on direct isolation and radiochemical purification of daughter 90 Y is proposed. The analysis time is 6-8 h. The chemical yield of the Y-carrier during the 90 Sr determination from 35 liters of seawater varies in the range 37-69%. The analysis uncertainty is 90 Sr from seawater and subsequent isolation of 90 Y

  10. Renewables 2013. Global Status Report

    Energy Technology Data Exchange (ETDEWEB)

    Sawin, J. L. [and others

    2013-07-01

    Renewable energy markets, industries, and policy frameworks have evolved rapidly in recent years. The Renewables Global Status Report provides a comprehensive and timely overview of renewable energy market, industry, investment, and policy developments worldwide. It relies on the most recent data available, provided by many contributors and researchers from around the world, all of which is brought together by a multi-disciplinary authoring team. The report covers recent developments, current status, and key trends; by design, it does not provide analysis or forecasts. This latest Renewables Global Status Report saw: a shift in investment patterns that led to a global decrease in clean energy investment; continuing growth in installed capacity due to significant technology cost reductions and increased investment in developing countries; renewables progressively supplementing established electricity systems, demonstrating that the implementation of suitable policies can enable the successful integration of higher shares of variable renewables; and the emergence of integrated policy approaches that link energy efficiency measures with the implementation of renewable energy technologies.

  11. Developing Government Renewable Energy Projects

    Energy Technology Data Exchange (ETDEWEB)

    Kurt S. Myers; Thomas L. Baldwin; Jason W. Bush; Jake P. Gentle

    2012-07-01

    The US Army Corps of Engineers has retained Idaho National Laboratory (INL) to conduct a study of past INL experiences and complete a report that identifies the processes that are needed for the development of renewable energy projects on government properties. The INL has always maintained expertise in power systems and applied engineering and INL’s renewable energy experiences date back to the 1980’s when our engineers began performing US Air Force wind energy feasibility studies and development projects. Over the last 20+ years of working with Department of Defense and other government agencies to study, design, and build government renewable projects, INL has experienced the do’s and don’ts for being successful with a project. These compiled guidelines for government renewable energy projects could include wind, hydro, geothermal, solar, biomass, or a variety of hybrid systems; however, for the purpose of narrowing the focus of this report, wind projects are the main topic discussed throughout this report. It is our thought that a lot of what is discussed could be applied, possibly with some modifications, to other areas of renewable energy. It is also important to note that individual projects (regardless the type) vary to some degree depending on location, size, and need but in general these concepts and directions can be carried over to the majority of government renewable energy projects. This report focuses on the initial development that needs to occur for any project to be a successful government renewable energy project.

  12. renewables 2011 - Global status report

    International Nuclear Information System (INIS)

    Sawin, Janet L.; Martinot, Eric; Barnes, Douglas; Martinot, Eric; McCrone, Angus; Roussell, Jodie; Sawin, Janet L.; Sims, Ralph; Sonntag-O'Brien, Virginia; Adib, Rana; Skeen, Jonathan; Musolino, Evan; Riahi, Lily; Mastny, Lisa

    2011-01-01

    Changes in renewable energy markets, investments, industries, and policies have been so rapid in recent years that perceptions of the status of renewable energy can lag years behind the reality. This report captures that reality and provides a unique overview of renewable energy worldwide as of early 2011. The report covers both current status and key trends; by design, it does not provide analysis or forecast the future. Global energy consumption rebounded in 2010 after an overall downturn in 2009. Renewable energy, which experienced no downturn in 2009, continued to grow strongly in all end-use sectors - power, heat and transport - and supplied an estimated 16% of global final energy consumption. Renewable energy accounted for approximately half of the estimated 194 gigawatts (GW) of new electric capacity added globally during the year. Renewables delivered close to 20% of global electricity supply in 2010, and by early 2011 they comprised one quarter of global power capacity from all sources. In several countries, renewables represent a rapidly growing share of total energy supply, including heat and transport

  13. Mitigation of global warming through renewable biomass

    International Nuclear Information System (INIS)

    Dhillon, R.S.; Wuehlisch, George von

    2013-01-01

    Rising level of atmospheric CO 2 and consequent global warming is evident. Global surface temperature have already increased by 0.8 °C over the 20th century and is projected to increase by 1.4–5.8 °C during the twenty-first century. The global warming will continue till atmospheric concentrations of the major greenhouse gases are stabilized. Among them, CO 2 is mainly responsible and is expected to account for about 60% of the warming over the next century. This study reviews advances on causes and consequences of global climate change and its impact on nature and society. Renewable biomass has tremendous potential to mitigate the global warming. Renewable biomass is expected to play a multifunctional role including food production, source of energy and fodder, biodiversity conservation, yield of goods and services to the society as well as mitigation of the impact of climate change. The review highlights the different management and research strategies in forestry, agriculture, agroforestry and grasslands to mitigate the global warming. -- Highlights: ► Rising level of atmospheric CO 2 and consequent global warming is evident. ► CO 2 is mainly responsible for global warming. ► Global temperature is predicted to increase by 1.4–5.8 °C during 21st century. ► Renewable biomass has great potential to mitigate the global warming

  14. Measurement of resonance integral of the 90Sr(n,γ)91Sr reaction

    International Nuclear Information System (INIS)

    Nakamura, Shoji; Furutaka, Kazuyoshi; Wada, Hiroaki; Katoh, Toshio; Harada, Hideo; Fujii, Toshiyuki; Yamana, Hajimu

    2001-01-01

    To obtain fundamental data for research on nuclear transmutation method of radioactive wastes, the resonance integral (I 0 ) of the 90 Sr(n,γ) 91 Sr reaction was measured with an activation method. (author)

  15. Isotope ratio 87Sr/86Sr in limestones from Bambui group, Brazil (MG)

    International Nuclear Information System (INIS)

    Kawashita, K.; Mizusaki, A.M.P.; Kiang, C.H.

    1987-01-01

    The Sr composition of ancient seawater can be estimated from the analysis of carbonate rocks and, in some cases, used to estimate the age of the analyzed carbonate. The normalized 87Sr/86Sr ratios in calcium carbonate fractions from 14 core samples in the Bambui Group near Montalvania, MG, were found to range between .7077 and .7280. The higher values are attributable to Sr isotopic exchange between silicate and carbonate phases during diagenesis. The ratio of .7077 obtained in two pure calcium carbonate samples is here suggested as the best aproximation for the 87Sr/86Sr value for the Bambui sea. This ratio is compatible with an age of about 700 Ma., estimated from the published 87Sr/86Sr curve of Veizer and others, an age in accordance with Quadros recent (1987, in preparation) identification of marine acritarchs from the latest Precambrian (Vendian). (author) [pt

  16. Preparation of 90Sr-90Y generator

    International Nuclear Information System (INIS)

    Jin Xiaohai; Yu Haibin; Zhang Jinming; Zhang Peixin; Lin Qiongfang

    1990-01-01

    In recent years, 90 Y has been considered as one of the best radionuclides for tumor radioimmunotherapy when chelated to tumor-associated antibodies. This evaluation is based on the superior properties of this radionuclide (suitable half-life, pure β-ray emitter of intermediate energy, stable daughters, and suitable chemical properties) and because it is available as a radionuclide generator product by decay of its 28a parent 90 Sr. The experimental conditions of 90 Sr- 90 Y generator are described. The elution efficiency of 90 Sr- 90 Y generator reaches 98%. One of the most important problems is the 90 Sr contamination breakthrough from the generator. The level of 90 Sr contamination must be controlled to the clinical standard. The cation exchange resin 732 (100-150 mesh) was successfully used for the separation of 90 Y from 90 Sr. The method used by the authors provides a 90 Y-HAc solution which is very simple and safe for administration to the patients. 90 Y was separated from 90 Sr almost completely, the level of the 90 Sr contamination per 740 MBq 90 Y product was only 0.74 kBq. However the toxicity of 90 Sr is extremely high, the human life-time permissible dose is 74 kBq, then 740 MBq of 90 Y is allowed to be administrated to a patient for 50-100 times

  17. Experiences with the determination of Sr-89 and Sr-90 using fast methods; Erfahrungen bei der Bestimmung von {sup 89}Sr und {sup 90}Sr mittels Schnellmethoden

    Energy Technology Data Exchange (ETDEWEB)

    Kowalik, C.; Fueger, J. [Thueringer Landesanstalt fuer Umwelt und Geologie, Jena (Germany). Landesmessstelle fuer Umweltradioaktivaet

    2014-01-20

    Quick methods of the measurement of {sup 89}Sr and {sup 90}Sr have a great importance in the supervision of the environmental radioactivity. It is necessary to receive in short time dependable analytical data to be able to carry out suitable assessments or to give recommendations. The aim of the investigations was to be guaranteed the demands for these methods (test preparation, measurement and evaluation). The use of the solid phase extraction by means of commercial Sr Resin trademark columns (4.4' (5')-Di-tert-butylcyclohexanol-18-kronen-6-aether) (Triskem) to the radiochemical separation of the Sr isotopes was suitable. The measurements occurred to the FHT 770 T12 - Multi Low Level Alpha/Beta Sample Counter (Thermo Scientific). The results contain the summary activities of all available Sr isotopes, as for example {sup 89}Sr and {sup 90}Sr. The calculations of the single activities occur about the mathematical algorithm of the linear development on the basis of the works of G. Kanisch. The first results show, this method is suitable for the analysis of {sup 89}Sr and {sup 90}Sr and is used therefore in future in Thuringia.

  18. Marine Renewable Energy Center

    Energy Technology Data Exchange (ETDEWEB)

    Vigeant, Paul [Univ. of Massachusetts, Dartmouth, MA (United States); Miller, John [Univ. of Massachusetts, Dartmouth, MA (United States); Howes, Brian [Univ. of Massachusetts, Dartmouth, MA (United States); McGowan, Jon G. [Univ. of Massachusetts, Amherst, MA (United States); Baldwin, Kenneth [Univ. of New Hampshire, Durham, NH (United States); Grilli, Annette [Univ. of Rhode Island, Kingston, RI (United States); Terray, Eugene [Woods Hole Oceanographic Inst., Woods Hole, MA (United States)

    2013-10-08

    Project Goals: The funding provided by this contract supported the following activities: A) Test Site Development; B) Seed Grant Funded Technology Development; C) Stakeholder Activities The first year of funding was dedicated to the formation of the NE MREC University Consortium which was comprised of University of Massachusetts Dartmouth (UMD) and Amherst (UMA), Massachusetts Institute of Technology (MIT), Woods Hole Oceanographic Institution (WHOI), University of New Hampshire (UNH), and the University of Rhode Island (URI). The consortium worked together to encourage research and promote benefits of obtaining energy from ocean wind, waves, tides and currents. In addition, NE MREC’s goal was to fund projects aimed at potential test sites with the first year funding going to studies of the potential for tidal device testing in Muskeget Channel, at the General Sullivan Bridge in New Hampshire, and for wave device testing at the proposed National Offshore Renewable Energy Innovation Zone (NOREIZ) located off the Massachusetts coast. The project spanned 4.5 years and addressed three specific tasks that are interrelated but also served as independent investigations.

  19. Renewables 2005. Global status report

    International Nuclear Information System (INIS)

    2005-01-01

    This report provides an overview of the status of renewable energy worldwide in 2005. It covers markets, investments, industries, policies, and rural (off-grid) renewable energy in developing countries. By design, the report does not provide analysis, recommendations, or conclusions. An extensive research and review process over several months involving more than 100 researchers and contributors has kept inaccuracies to a minimum. REN21 sees this report as the beginning of an active exchange of views and information. This report reveals some surprising facts about renewable energy, many reflecting strong growth trends and increasing significance relative to conventional energy. (au)

  20. Renewables 2005. Global status report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2005-07-01

    This report provides an overview of the status of renewable energy worldwide in 2005. It covers markets, investments, industries, policies, and rural (off-grid) renewable energy in developing countries. By design, the report does not provide analysis, recommendations, or conclusions. An extensive research and review process over several months involving more than 100 researchers and contributors has kept inaccuracies to a minimum. REN21 sees this report as the beginning of an active exchange of views and information. This report reveals some surprising facts about renewable energy, many reflecting strong growth trends and increasing significance relative to conventional energy. (au)

  1. Renewables 2005 - Global status report

    International Nuclear Information System (INIS)

    Martinot, Eric

    2005-01-01

    This report provides an overview of the status of renewable energy worldwide in 2005. It covers markets, investments, industries, policies, and rural (off-grid) renewable energy in developing countries. By design, the report does not provide analysis, recommendations, or conclusions. An extensive research and review process over several months involving more than 100 researchers and contributors has kept inaccuracies to a minimum. REN21 sees this report as the beginning of an active exchange of views and information. This report reveals some surprising facts about renewable energy, many reflecting strong growth trends and increasing significance relative to conventional energy

  2. Renewable, ethical? Assessing the energy justice potential of renewable electricity

    Directory of Open Access Journals (Sweden)

    Aparajita Banerjee

    2017-08-01

    Full Text Available Energy justice is increasingly being used as a framework to conceptualize the impacts of energy decision making in more holistic ways and to consider the social implications in terms of existing ethical values. Similarly, renewable energy technologies are increasingly being promoted for their environmental and social benefits. However, little work has been done to systematically examine the extent to which, in what ways and in what contexts, renewable energy technologies can contribute to achieving energy justice. This paper assesses the potential of renewable electricity technologies to address energy justice in various global contexts via a systematic review of existing studies analyzed in terms of the principles and dimensions of energy justice. Based on publications including peer reviewed academic literature, books, and in some cases reports by government or international organizations, we assess renewable electricity technologies in both grid integrated and off-grid use contexts. We conduct our investigation through the rubric of the affirmative and prohibitive principles of energy justice and in terms of its temporal, geographic, socio-political, economic, and technological dimensions. Renewable electricity technology development has and continue to have different impacts in different social contexts, and by considering the different impacts explicitly across global contexts, including differences between rural and urban contexts, this paper contributes to identifying and understanding how, in what ways, and in what particular conditions and circumstances renewable electricity technologies may correspond with or work to promote energy justice.

  3. SR-B1 Is a Silica Receptor that Mediates Canonical Inflammasome Activation

    Directory of Open Access Journals (Sweden)

    Misato Tsugita

    2017-01-01

    Full Text Available The inhalation of silica dust is associated with fibrosis and lung cancer, which are triggered by macrophage inflammatory responses; however, how macrophages recognize silica remains largely unknown. Here, we identify by functional expression cloning the class B scavenger receptor SR-B1 as a silica receptor. Through an extracellular α-helix, both mouse and human SR-B1 specifically recognized amorphous and crystalline silica, but not titanium dioxide nanoparticles, latex nanoparticles, or monosodium urate crystals, although all particles exhibited negative surface potentials. Genetic deletion of SR-B1 and masking of SR-B1 by monoclonal antibodies showed that SR-B1-mediated recognition of silica is associated with caspase-1-mediated inflammatory responses in mouse macrophages and human peripheral blood monocytes. Furthermore, SR-B1 was involved in silica-induced pulmonary inflammation in mice. These results indicate that SR-B1 is a silica receptor associated with canonical inflammasome activation.

  4. Electrostatic analysis of n-doped SrTiO3 metal-insulator-semiconductor systems

    International Nuclear Information System (INIS)

    Kamerbeek, A. M.; Banerjee, T.; Hueting, R. J. E.

    2015-01-01

    Electron doped SrTiO 3 , a complex-oxide semiconductor, possesses novel electronic properties due to its strong temperature and electric-field dependent permittivity. Due to the high permittivity, metal/n-SrTiO 3 systems show reasonably strong rectification even when SrTiO 3 is degenerately doped. Our experiments show that the insertion of a sub nanometer layer of AlO x in between the metal and n-SrTiO 3 interface leads to a dramatic reduction of the Schottky barrier height (from around 0.90 V to 0.25 V). This reduces the interface resistivity by 4 orders of magnitude. The derived electrostatic analysis of the metal-insulator-semiconductor (n-SrTiO 3 ) system is consistent with this trend. When compared with a Si based MIS system, the change is much larger and mainly governed by the high permittivity of SrTiO 3 . The non-linear permittivity of n-SrTiO 3 leads to unconventional properties such as a temperature dependent surface potential non-existent for semiconductors with linear permittivity such as Si. This allows tuning of the interfacial band alignment, and consequently the Schottky barrier height, in a much more drastic way than in conventional semiconductors

  5. Effect of Wood Aging on Wine Mineral Composition and 87Sr/86Sr Isotopic Ratio.

    Science.gov (United States)

    Kaya, Ayse D; Bruno de Sousa, Raúl; Curvelo-Garcia, António S; Ricardo-da-Silva, Jorge M; Catarino, Sofia

    2017-06-14

    The evolution of mineral composition and wine strontium isotopic ratio 87 Sr/ 86 Sr (Sr IR) during wood aging were investigated. A red wine was aged in stainless steel tanks with French oak staves (Quercus sessiliflora Salisb.), with three industrial scale replicates. Sampling was carried out after 30, 60, and 90 days of aging, and the wines were evaluated in terms of general analysis, phenolic composition, total polysaccharides, multielement composition, and Sr IR. Li, Be, Mg, Al, Sc, Ti, V, Mn, Co, Ni, Cu, Zn, Ga, Ge, As, Rb, Sr, Y, Zr, Mo, Sb, Cs, Ba, Pr, Nd, Sm, Eu, Dy, Ho, Er, Yb, Lu, Tl, and Pb elements and 87 Sr/ 86 Sr were determined by quadrupole inductively coupled plasma mass spectrometry (Q-ICP-MS) and Na, K, Ca, and Fe by flame atomic absorption spectrometry (FAAS). Two-way ANOVA was applied to assess wood aging and time effect on Sr IR and mineral composition. Wood aging resulted in significantly higher concentrations of Mg, V, Co, Ni, and Sr. At the end of the aging period, wine exhibited statistically identical Sr IR compared to control. Study suggests that wood aging does not affect 87 Sr/ 86 Sr, not precluding the use of this parameter for wine traceability purposes.

  6. Renewables 2010 - Global status report

    International Nuclear Information System (INIS)

    Sawin, Janet L.; Martinot, Eric; Sonntag-O'Brien, Virginia; McCrone, Angus; Roussell, Jodie; Barnes, Douglas; Flavin, Christopher; Mastny, Lisa; Kraft, Diana; Wang, Shannon; Ellenbeck, Saskia; Ilieva, Lili; Griebenow, Christof; Adib, Rana; Lempp, Philippe; Welker, Bettina

    2010-01-01

    Changes in renewable energy markets, investments, industries, and policies have been so rapid in recent years that perceptions of the status of renewable energy can lag years behind the reality. This report captures that reality and provides a unique overview of renewable energy worldwide as of early 2010. The report covers both current status and key trends. By design, the report does not provide analysis, discuss current issues, or forecast the future. Many of the trends reflect the increasing significance of renewable energy relative to conventional energy sources (including coal, gas, oil, and nuclear). By 2010, renewable energy had reached a clear tipping point in the context of global energy supply. Renewables comprised fully one quarter of global power capacity from all sources and delivered 18 percent of global electricity supply in 2009. In a number of countries, renewables represent a rapidly growing share of total energy supply-including heat and transport. The share of households worldwide employing solar hot water heating continues to increase and is now estimated at 70 million households. And investment in new renewable power capacity in both 2008 and 2009 represented over half of total global investment in new power generation. Trends reflect strong growth and investment across all market sectors-power generation, heating and cooling, and transport fuels. Grid-connected solar PV has grown by an average of 60 percent every year for the past decade, increasing 100-fold since 2000. During the past five years from 2005 to 2009, consistent high growth year-after-year marked virtually every other renewable technology. During those five years, wind power capacity grew an average of 27 percent annually, solar hot water by 19 percent annually, and ethanol production by 20 percent annually. Biomass and geothermal for power and heat also grew strongly. Much more active policy development during the past several years culminated in a significant policy milestone

  7. Phase transformation of the brownmillerite SrCoO{sub 2.5} thin film through alkaline water electrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Tambunan, Octolia Togibasa; Lee, Min Young; Kim, Deok Hyeon; Parwanta, Kadek Juliana; Jung, Chang Uk [Hankuk University of Foreign Studies, Yongin (Korea, Republic of)

    2014-06-15

    A phase transformation from insulating brownmillerite SrCoO{sub 2.5} to conducting perovskite SrCoO{sub 3} through electrochemical oxidation has been demonstrated for thin films of SrCoO{sub x} on a SrTiO{sub 3} (001) substrate. The cobalt-oxide film strongly favors the brownmillerite phase of SrCoO{sub 2.5} instead of the perovskite phase of SrCoO{sub 3} on a SrTiO{sub 3} (001) substrate due to its low lattice mismatch. Therefore, the phase transformation has its own retention. The alkaline water electrolysis occurs between the copper cathode and the SrCoO{sub 2.5} film anode. The H{sup +} ions are attracted to the cathode and generate H{sub 2} gas. The OH{sup -} ions are attracted to the film's surface and generate a rich amount of oxygen to fill the oxygen vacancy channel of brownmillerite SrCoO{sub 2.5}. The phase transformation was verified from the change in the out-of-plane lattice constant and the change in the resistivity of the electrolyzed film.

  8. Financing of Renewable Energy Projects

    International Nuclear Information System (INIS)

    Santizo, Rodolfo; Berganza, Jose

    2000-01-01

    The paper describes the role of the Banco Centroamericano de Integracion Economica in financing renewable energy projects in Central America. Also decribes the different financing modes to the goverment and private sectors

  9. Nuclear energy and renewable energies

    International Nuclear Information System (INIS)

    1994-01-01

    The nuclear energy and the renewable energies namely: solar energy, wind energy, geothermal energy and biomass are complementary. They are not polluting and they are expected to develop in the future to replace the fossil fuels

  10. VT Renewable Energy Sites - Hydroelectric

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The Renewable Energy Atlas of Vermont and this dataset were created to assist town energy committees, the Clean Energy Development Fund and other...

  11. VT Renewable Energy Sites - Geothermal

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The Renewable Energy Atlas of Vermont and this dataset were created to assist town energy committees, the Clean Energy Development Fund and other...

  12. VT Renewable Energy Sites - Landfills

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The Renewable Energy Atlas of Vermont and this dataset were created to assist town energy committees, the Clean Energy Development Fund and other...

  13. VT Renewable Energy Sites - Wind

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The Renewable Energy Atlas of Vermont and this dataset were created to assist town energy committees, the Clean Energy Development Fund and other...

  14. Renewable energies in United Kingdom

    International Nuclear Information System (INIS)

    Baize, T.

    1993-01-01

    An evaluation of research and development policy in United Kingdom on renewable energy sources is presented with economical studies (short or long term profitability), engaged programs and electric production. (A.B.). refs. tabs

  15. Which leadership for renewable energies?

    International Nuclear Information System (INIS)

    Chaumien, Marielle

    2016-02-01

    This publication first outlines that France is late in deploying renewable energies by 2020. It comments the application of the Energy multi-year plan (PPE), evokes the content of a report by the French Court of Auditors about costs and means of implementation of transition (with notably the issue of maintenance of nuclear plants). It also shows that European Union is not a leader in renewable energies any more, that some European countries are changing sides, that figures and trends must be carefully compared with those in the field of fossil and nuclear energies, that all energies are not all the same, that jobs and system integration are also important, that investments and attractiveness of countries in renewable energies must be assessed, and that a mobilisation on small scale and consumer-based renewable energies is required. Ten recommendations are made for France to support the EU leadership development

  16. VT Renewable Energy Sites - Solar

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The Renewable Energy Atlas of Vermont and this dataset were created to assist town energy committees, the Clean Energy Development Fund and other...

  17. Renewable energy in the EU

    International Nuclear Information System (INIS)

    Lambert, Allan; Myers, Stephen; Trow, Stuart

    1998-05-01

    Contains Executive Summary and Chapters on: Overview of European Renewable Energy; Austria; Belgium; Denmark; Finland; France; Germany; Greece; Ireland; Italy; Luxembourg; The Netherlands; Portugal; Spain; Sweden; The United Kingdom. (Author)

  18. Nanostructured Materials for Renewable Energy

    Energy Technology Data Exchange (ETDEWEB)

    None

    2009-11-01

    This factsheet describes a research project whose overall objective is to advance the fundamental understanding of novel photoelectronic organic device structures integrated with inorganic nanostructures, while also expanding the general field of nanomaterials for renewable energy devices and systems.

  19. Renewables Global Futures Report: Great debates towards 100% renewable energy

    International Nuclear Information System (INIS)

    Teske, Sven; Fattal, Alex; Lins, Christine; Hullin, Martin; Williamson, Laura E.

    2017-01-01

    The first version of REN21's Renewables Global Futures Report (GFR) published in January 2013 identified a panorama of likely future debates related to the renewable energy transition. As a reflection of the wide range of contemporary thinking by the many experts interviewed for the report, it did not present just one vision of the future but rather a 'mosaic' of insights. Given the positive feedback in response to the first edition, a new edition has been prepared, continuing where the last one left off. The objective of this report is to gather opinions about the feasibility of a 100% renewable energy future, and the macro-economic impacts it would entail. In so doing, the report reflects on the debates of 2013, and tracks their evolution to the present time. Some remain, some have changed, some have been overtaken by progress, and new ones have arisen. They are summarised here as the Great Debates in renewable energy. The questionnaire for the survey was developed in close cooperation between the REN21 Secretariat, the Institute for Sustainable Future (ISF) of the University of Technology Sydney/Australia (UTS) and the Institute for Advanced Sustainability Studies (IASS) in Potsdam/Germany. It covered the following topics: 1. How much renewables?; 2. Power sector; 3. Heating and cooling; 4. Transport; 5. Storage; 6. Demand-side management and energy efficiency; 7. Integration of sectors; 8. Macro-economic considerations; 9. Technology and costs; 10. Policy; 11. Cities; 12. Distributed renewable energy/energy access; 13. Barriers/challenges/enablers. 114 experts were interviewed in total; the average interview time was approximately one hour. The interviews were conducted between May and October 2016. The questionnaire was also mirrored in an online version and used both by interviewers and interviewees to record the interview process. Interviewees were selected from the following regions: Africa, Australia and Oceania, China, Europe, India, Japan, Latin America

  20. Sorption-scintillation determination of 90Sr in natural water

    International Nuclear Information System (INIS)

    Andryushchenko, A.Yu.; Blank, A.B.; Budakovsky, S.V.; Tarasenko, O.A.; Shevtsov, N.I.

    2003-01-01

    A porous composite material is described for determination of radionuclides in aquatic objects of the environment. Possibilities have been studied for the use of this material in monitoring of 90 Sr content in natural waters. The composite is a scintillator with through pores, the surface of which is impregnated by a sorbent that is selective with respect to strontium. The structure of the material allows combination of two processes--concentrating the radionuclide and measuring its activity. Studies were carried out using both model systems based on reference radioactive solutions and samples of natural water contaminated with radionuclides. It is shown that the use of the proposed method for analysis of natural water allows determination in water of 4x10 -2 Bq l -1 of 90 Sr, which is by two orders of magnitude lower than its maximum acceptable concentration

  1. Panorama 2011: Ocean renewable energies

    International Nuclear Information System (INIS)

    Demoulin, P.; Vinot, S.

    2011-01-01

    Our society is looking increasingly to renewable energy sources in the face of the energy and environmental challenges with which it is grappling. As far as ocean renewable energies are concerned, a wide range of technologies is currently being experimented with, including wind power and energy derived from waves and tidal currents. They are all at varying levels of maturity, and bring with them very different technical and economic challenges. (author)

  2. GRENADA. Renewables Readiness Assessment 2012

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-07-01

    Grenada, like many Caribbean islands, is dependent on costly oil imports for its energy needs, including the generation of electricity. The transition to renewable energy could potentially support price reductions and improve the overall competitiveness of key sectors of the economy, particularly tourism. This report provides facts and analysis to support the country's discussion on ways to move forward with the renewable energy agenda. IRENA is ready to provide support in the implementation of the actions identified in this report.

  3. The renewable energies: the landscape

    International Nuclear Information System (INIS)

    Acket, C.; Bacher, P.

    2005-03-01

    If one takes into account the hydroelectric power, the France is the first european country in the renewable energies domain. The position is also honorable concerning the wood energy. Meanwhile, for the solar and wind energy, France is late. To discuss this debate, the authors bring together today data on the renewable energies, offer some proposals for the next 50 years taking into account the reduction of greenhouse gases emission for 2050. (A.L.B.)

  4. Renewable Energy Education in India

    OpenAIRE

    Bajpai Shrish; Kidwai Naimur Rahman

    2017-01-01

    The issue of renewable energy sources that have great potential to give solutions to the longstanding energy problems of India has been considered. It has been stated that renewable energy sources are an important part of India’s plan to increase energy security and provide new generation with ample job opportunities. India’s plans to move towards green technology and address environmental concerns associated with the country and the world have been characterized. The peculiarities of the ren...

  5. Local investment in renewable energies

    International Nuclear Information System (INIS)

    2003-11-01

    Although the vast majority of renewable energies projects are established by commercial developers, some of them are financed by ''ordinary citizens'' pooling together through different schemes. This is particularly frequent in Denmark and Germany, possibly a key reason for the continuous and so successful growth of various renewable energies sources in these countries. This guideline aims to define the term of local investment and provides examples of development and recommendations. (A.L.B.)

  6. Regional Integration of Renewable Energies

    International Nuclear Information System (INIS)

    Amador Guerra, J.; Dominguez Bravo, J.

    2000-01-01

    The aim of this report is to show how Energetic Planning and Territorial Policy should be working together for a better integration of Renewable Energies into Region. This Integration should to contemplate social, economic and environmental aspects of the territory. The report has been classified into 7 items: planning, energetic scenarios, technology transfer for Renewable Energies dissemination, barriers for this dissemination, environmental aspects, European Union Policy and Decision Support Systems (and specially GIS). (Author) 54 refs

  7. Renewable energies in the EU

    International Nuclear Information System (INIS)

    Heller, W.

    2008-01-01

    On January 23, 2008, the European Commission presented proposals in the form of a directive in an effort to give more specific shape to the objective adopted in the spring, i.e. to increase to 20% by 2020 the share of renewable energies in energy consumption in the Community. The proposal was to include legally binding goals for the overall share of renewable energy sources and the share of biofuels in the transport sector. The proposed directive on 'promoting the use of energy from renewable sources' calls upon each member state to ensure that its share of energy from renewable sources in the total energy consumption in 2020 at least corresponds to the target mentioned in Annex I Part A. In addition to the targets, the EU Commission charted a tentative course towards a minimum increase in the share of renewable energies in the period between 2011 and 2020. Finally, the member states are obliged to adopt national action plans. Unfortunately, the EU is missing an important target in its proposed directive: It should establish a framework for harmonized conditions promoting the use of renewable energies. One aspect to be welcomed is the introduction of a system of certificates of origin. It represents the entry, in principle, into a trading system with certificates of origin. The Green Package incorporates a wealth of new approaches. They will have to be tested and, if necessary, supplemented. Something else is evident, however: The directive established the foundations of a vast number of new regulations and red tape. (orig.)

  8. Renewable Energy Country Profiles. Pacific

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-09-15

    The IRENA Renewable Energy Country Profiles take stock of the latest development of renewable energy in two regions where renewable energy can make a significant contribution to combat climate change and bring modern energy services to everyone: Africa and the Pacific. These two regions are presented separately in this volume and its sister publication. The country profiles combine elements of IRENA analysis with the latest information available from a vast array of sources in order to give a brief yet comprehensive and up-to-date picture of the situation of renewable energy that includes energy supply, electrical capacity, energy access, policies, targets, investment climate, projects and endowment in renewable energy resources. Because of the different timelines of these sources, data presented here refer to years between 2008 and 2012. Data availability also differs from country to country, which makes comparison with a wider regional group possible only for the year for which figures are available for all the members of the group; while this may not be the most recent year, the differences between countries, regions and the world remain striking. The current country profiles are just a starting point; they will be extended upon with new indicators to make them more informative, and maintained as a live product on the IRENA website as a key source of information on renewable energy.

  9. Renewable energy islands in Europe

    Energy Technology Data Exchange (ETDEWEB)

    Oestergaard, Iben [ed.

    1998-12-31

    This publication includes a compiled presentation of various aspects concerning the possible transformation of some European islands into renewable energy communities and these projects were presented by a selection of pioneer islands at the first European Seminar on Renewable Energy Islands, held on the Danish island of Samsoee, 29-30 June 1998. This issue has increased in importance with the presentation of the ambitious EU-White Paper: `Energy for the future: Renewable Sources of Energy` which was adopted in 1998. One of the key elements of the strategy for an accelerated implementation of renewable energy is to transform 100 localities within Europe into communities which are to be 100% self-sufficient with renewable energy before 2010. In line with this strategy, the Danish Government appointed the island of Samsoe towards the end of 1997 to be the first `official` Danish, renewable energy island. This is to serve as a demonstration project for other local communities, both in Denmark as well as in the rest Europe. Gothland, Madeira, Canary Islands, Cape Verde, Arki, Crete, Minorca and Orkney Islands were represented. Environmental advantages of wind, solar and wave power for distant island communities were indicated. Serious savings would be achieved by limitation of fossil fuel import and utilization of local resources. (EG)

  10. Renewable Energy Country Profiles. Africa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-02-15

    The IRENA Renewable Energy Country Profiles take stock of the latest development of renewable energy in two regions where renewable energy can make a significant contribution to combat climate change and bring modern energy services to everyone: Africa and the Pacific. These two regions are presented separately in this volume and its sister publication. The country profiles combine elements of IRENA analysis with the latest information available from a vast array of sources in order to give a brief yet comprehensive and up-to-date picture of the situation of renewable energy that includes energy supply, electrical capacity, energy access, policies, targets, investment climate, projects and endowment in renewable energy resources. Because of the different timelines of these sources, data presented here refer to years between 2008 and 2012. Data availability also differs from country to country, which makes comparison with a wider regional group possible only for the year for which figures are available for all the members of the group; while this may not be the most recent year, the differences between countries, regions and the world remain striking. The current country profiles are just a starting point; they will be extended upon with new indicators to make them more informative, and maintained as a live product on the IRENA website as a key source of information on renewable energy.

  11. Vadose Zone Infiltration Rate at Hanford, Washington, Inferred from Sr Isotope Measurements

    International Nuclear Information System (INIS)

    Maher, Katharine; DePaolo, Donald J.; Conrad, Mark E.; Serne, R. Jeffrey

    2003-01-01

    Sr isotope ratios were measured in the pore water, acid extracts, and sediments of a 70-m vadose zone core to obtain estimates of the long-term infiltration flux for a site in the Hanford/DOE complex in eastern Washington State. The 87Sr/86Sr values of the pore waters decrease systematically with depth, from a high value of 0.721 near the surface toward the bulk sediment average value of 0.711. Estimates of the bulk weathering rate combined with Sr isotopic data were used to constrain the long-term (century to millenial scale) natural diffuse infiltration flux for the site given both steady state and nonsteady state conditions. The models suggest that the infiltration fluc for the site is 7+- 3 mm/yr. The method shows potential for providing long-term in situ estimates of infiltration rates for deep heterogeneous vadose zones

  12. Measurement of Ca, Zn and Sr in enamel of human teeth by XRF

    Energy Technology Data Exchange (ETDEWEB)

    Wielopolski, L.; Featherstone, J.D.B.; Cohn, S.H.

    1984-01-01

    Energy dispersive x-ray fluorescence (EDXRF) has been employed to measure Ca, Zn, and Sr in enamel of human teeth. The calibration of the EDXRF system was performed by comparing Sr/Ca ratios with values obtained by atomic absorption analysis of acid etched biopsies of the enamel surface. Two calibration lines were obtained, one line for untreated teeth and the second line for teeth immersed (treated) in solutions containing Sr. A simple analytical model demonstrated that the two calibration lines were the result of the difference in the depth of the enamel sampled by EDXRF and by the acid-etched biopsy. The multi-elemental, non-destructive and quantitative aspects of EDXRF permit the sequential monitoring of the effects of Sr and Zn ions on the mineralization and demineralization processes in human enamel. The portability of the system and adaptability to non-invasive measurements makes it suitable for field studies. 26 references, 4 figures.

  13. Measurement of Ca, Zn and Sr in enamel of human teeth by XRF

    International Nuclear Information System (INIS)

    Wielopolski, L.; Featherstone, J.D.B.; Cohn, S.H.

    1984-01-01

    Energy dispersive x-ray fluorescence (EDXRF) has been employed to measure Ca, Zn, and Sr in enamel of human teeth. The calibration of the EDXRF system was performed by comparing Sr/Ca ratios with values obtained by atomic absorption analysis of acid etched biopsies of the enamel surface. Two calibration lines were obtained, one line for untreated teeth and the second line for teeth immersed (treated) in solutions containing Sr. A simple analytical model demonstrated that the two calibration lines were the result of the difference in the depth of the enamel sampled by EDXRF and by the acid-etched biopsy. The multi-elemental, non-destructive and quantitative aspects of EDXRF permit the sequential monitoring of the effects of Sr and Zn ions on the mineralization and demineralization processes in human enamel. The portability of the system and adaptability to non-invasive measurements makes it suitable for field studies. 26 references, 4 figures

  14. Measurement of Ca, Zn, and Sr in enamel of human teeth by XRF

    International Nuclear Information System (INIS)

    Wielopolski, L.; Featherstone, J.D.b.; Cohn, S.H.

    1984-01-01

    Energy dispersive x-ray fluorescence (EDXRF) has been employed to measure Ca, Zn, and Sr in enamel of human teeth. The calibration of the EDXRF system was performed by comparing Sr/Ca ratios with values obtained by atomic absorption analysis of acid etched biopsies of the enamel surface. Two calibration lines were obtained, one line for untreated teeth and the second line for teeth immersed (treated) in solutions containing Sr. A simple analytical model demonstrated that the two calibration lines were the result of the difference in the depth of the enamel sampled by EDXRF and by the acid-etched biopsy. The multi-elemental, non-destructive and quantitative aspects of EDXRF permit the sequential monitoring of the effects of Sr and Zn ions on the mineralization and demineralization processes in human enamel. The portability of the system and adaptability to non-invasive measurements makes it suitable for field studies. 26 references, 4 figures

  15. Review of SR 97 performance assessment

    International Nuclear Information System (INIS)

    Glynn, P.D.

    2000-01-01

    This review has identified many technical problems in the SR 97 performance assessment. The general impression of this reviewer is that SKB has been disingenuous in its performance assessment effort. It has not cited important differences of opinion with its own views. Furthermore, there are many inconsistencies in the SR 97 report that all together leave the impression that there are many more uncertainties in the SR 97 performance assessment than SKB would perhaps care to admit. Additionally, despite SKB's statements to the contrary, many of the analyses conducted for the SR 97 performance assessment can be clearly shown not to have been based on 'conservative' assumptions. Finally, SKB has made little effort to consider possible coupling effects between their different scenarios in SR 97. This is a serious flaw in the SR 97 performance assessment. The comments in this review should not be taken to imply that the KBS-3 nuclear waste disposal method will not be able to meet the safety and radiation protection requirements which SKI and SSI have specified in recent years. Instead, my conclusion is simply that the SR 97 performance assessment of the KBS-3 method would have been more believable had it been based on a forthright and comprehensive discussion of facts, uncertainties and opinions, and on a more conservative choice of assumptions. As it stands, the SR 97 performance assessment is not very credible

  16. Revealing the atomic structure and strontium distribution in nanometer-thick La0.8Sr0.2CoO3−δ grown on (001)-oriented SrTiO3

    KAUST Repository

    Feng, Zhenxing; Yacoby, Yizhak; Hong, Wesley T.; Zhou, Hua; Biegalski, Michael D.; Christen, Hans M.; Shao-Horn, Yang

    2014-01-01

    Surface segregation in metal oxides can greatly influence the oxygen transport and surface oxygen exchange kinetics critical to the performance of solid-state devices such as oxygen permeation membranes and solid oxide fuel/electrolytic cell electrodes. Unfortunately detecting elemental distributions at the atomic scale near the surface remains challenging, which hampers the understanding of underpinning mechanisms and control of surface segregation for the design of high-performance materials. Using the coherent Bragg rod analysis (COBRA) method, we report the first direct 3D atomic imaging of a 4 nm-thick "La0.8Sr0.2CoO 3-δ"/SrTiO3 epitaxial film. Of significance, energy differential COBRA revealed pronounced Sr segregation (La 1-xSrxCoO3-δ, x ∼ 0.4) in the four unit cells from the top surface while complete Sr depletion was detected in the five unit cells from the "La0.8Sr0.2CoO 3-δ"/SrTiO3 interface. The drastic strontium compositional changes in the film were associated with large changes in the atomic positions of apical oxygen sites in the perovskite structure. Such Sr segregation tendencies toward the surface were also found in nominal "La0.6Sr0.4CoO3-δ" thin films, which can greatly enhance the surface oxygen exchange properties of oxides. The results presented here show that COBRA and the differential COBRA methods can be used to investigate a variety of electrochemically active systems providing atomic scale structural and chemical information that can help understand the physical and chemical properties of these systems and serve as a basis for comparison with DFT calculations. © 2014 The Royal Society of Chemistry.

  17. Interactions between renewable energy policy and renewable energy industrial policy: A critical analysis of China's policy approach to renewable energies

    International Nuclear Information System (INIS)

    Zhang, Sufang; Andrews-Speed, Philip; Zhao, Xiaoli; He, Yongxiu

    2013-01-01

    This paper analyzes China's policy approach to renewable energies and assesses how effectively China has met the ideal of appropriate interactions between renewable energy policy and renewable energy industrial policy. First we briefly discuss the interactions between these two policies. Then we outline China's key renewable energy and renewable industrial policies and find that China's government has well recognized the need for this policy interaction. After that, we study the achievements and problems in China's wind and solar PV sector during 2005–2012 and argue that China's policy approach to renewable energies has placed priority first on developing a renewable energy manufacturing industry and only second on renewable energy itself, and it has not effectively met the ideal of appropriate interactions between renewable energy policy and renewable energy industrial policy. Lastly, we make an in-depth analysis of the three ideas underlying this policy approach, that is, the green development idea, the low-carbon leadership idea and indigenous innovation idea. We conclude that Chinas' policy approach to renewable energies needs to enhance the interactions between renewable energy policy and renewable energy industrial policy. The paper contributes to a deeper understanding of China's policy strategy toward renewable energies. -- Highlights: •Interactions between renewable energy policy and renewable energy industrial policy are discussed. •China's key renewable energy and renewable energy industrial policies are outlined. •Two empirical cases illustrate China's policy approach to renewable energies. •We argue that China needs to enhance the interactions between the two policies. •Three ideas underlie China's policy approach to renewable energies

  18. 48 CFR 570.401 - Renewal options.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 4 2010-10-01 2010-10-01 false Renewal options. 570.401... Requirements 570.401 Renewal options. (a) Exercise of options. Before exercising an option to renew, follow the... survey. Before exercising an option to renew a lease, review current market information to ensure the...

  19. 2012 Renewable Energy Data Book (Book)

    Energy Technology Data Exchange (ETDEWEB)

    Gelman, R.

    2013-10-01

    This Renewable Energy Data Book for 2012 provides facts and figures in a graphical format on energy in general, renewable electricity in the United States, global renewable energy development, wind power, solar power, geothermal power, biopower, hydropower, advanced water power, hydrogen, renewable fuels, and clean energy investment.

  20. 2011 Renewable Energy Data Book (Book)

    Energy Technology Data Exchange (ETDEWEB)

    Gelman, R.

    2012-10-01

    This Renewable Energy Data Book for 2011 provides facts and figures on energy in general, renewable electricity in the United States, global renewable energy development, wind power, solar energy, geothermal power, biopower, hydropower, advanced water power, hydrogen, renewable fuels, and clean energy investments.

  1. 2010 Renewable Energy Data Book (Book)

    Energy Technology Data Exchange (ETDEWEB)

    Gelman, R.

    2011-10-01

    This Renewable Energy Data Book for 2010 provides facts and figures on energy in general, renewable electricity in the United States, global renewable energy development, wind power, solar energy, geothermal power, biopower, hydropower, advanced water power, hydrogen, renewable fuels, and clean energy investments.

  2. 2013 Renewable Energy Data Book (Book)

    Energy Technology Data Exchange (ETDEWEB)

    Esterly, S.

    2014-12-01

    This Renewable Energy Data Book for 2013 provides facts and figures on energy in general, renewable electricity in the United States, global renewable energy development, wind power, solar power, geothermal power, biopower, hydropower, advanced water power, hydrogen, renewable fuels, and clean energy investment.

  3. Renewal processes with costs and rewards

    NARCIS (Netherlands)

    Vlasiou, M.; Cochran, J.J.; Cox, L.A.; Keskinocak, P.; Kharoufeh, J.P.; Smith, J.C.

    2011-01-01

    We review the theory of renewal reward processes, which describes renewal processes that have some cost or reward associated with each cycle. We present a new simplified proof of the renewal reward theorem that mimics the proof of the Elementary Renewal Theorem and avoids the technicalities in the

  4. Surface Roughness and Grain Size Characterization of Annealing Temperature Effect For Growth Gallium and Tantalum Doped Ba0.5 Sr0.5TiO3Thin Film

    Directory of Open Access Journals (Sweden)

    Irzaman

    2009-01-01

    Full Text Available Thin films 10 % gallium oxide doped barium strontium titanate (BGST and 10 % tantalum oxide doped barium strontium titanate (BTST were prepared on p-type Si (100 substrates using chemical solution deposition (CSD method with 1.00 M precursor. The films were deposited by spin coating method with spinning speed at 3000 rpm for 30 seconds. The post deposition annealing of the films were carried out in a furnace at 200oC, 240oC, 280oC (low temperature for 1 hour in oxygen gas atmosphere. The surface roughness and grain size analysis of the grown thin films are described by atomic force microscope (AFM method at 5000 nm x 5000 nm area. The rms surface roughness BGST thin films at 5000 nm x 5000 nm area are 0.632 nm, 0.564 nm, 0.487 nm for temperature 200oC, 240oC, 280oC, respectively, whereas the grain size (mean diameter are 238.4 nm, 219.0 nm, 185.1 nm for temperature 200oC, 240oC, 280oC, respectively. In fact, to increase annealing temperature from 200oC to 280oC would result in decreasing the rms roughness and grain size. Therefore, rms roughness and grain size would have the strong correlation annealing temperature.

  5. Thermodynamic Modeling of Sr/TRU Removal

    International Nuclear Information System (INIS)

    Felmy, A.R.

    2000-01-01

    This report summarizes the development and application of a thermodynamic modeling capability designed to treat the Envelope C wastes containing organic complexants. A complete description of the model development is presented. In addition, the model was utilized to help gain insight into the chemical processes responsible for the observed levels of Sr, TRU, Fe, and Cr removal from the diluted feed from tank 241-AN-107 which had been treated with Sr and permanganate. Modeling results are presented for Sr, Nd(III)/Eu(III), Fe, Cr, Mn, and the major electrolyte components of the waste (i.e. NO 3 , NO 2 , F,...). On an overall basis the added Sr is predicted to precipitate as SrCO 3 (c) and the MnO 4 - reduced by the NO 2 - and precipitated as a Mn oxide. These effects result in only minor changes to the bulk electrolyte chemistry, specifically, decreases in NO 2 - and CO 3 2- , and increases in NO 3 - and OH - . All of these predictions are in agreement with the experimental observations. The modeling also indicates that the majority of the Sr, TRU's (or Nd(III)/Eu(III)) analogs, and Fe are tied up with the organic complexants. The Sr and permanganate additions are not predicted to effect these chelate complexes significantly owing to the precipitation of insoluble Mn oxides or SrCO 3 . These insoluble phases maintain low dissolved concentrations of Mn and Sr which do not affect any of the other components tied up with the complexants. It appears that the removal of the Fe and TRU'S during the treatment process is most likely as a result of adsorption or occlusion on/into the Mn oxides or SrCO 3 , not as direct displacement from the complexants into precipitates. Recommendations are made for further studies that are needed to help resolve these issues

  6. Mirror decay of $^{75}$Sr

    CERN Document Server

    Huikari, J; Algora, A; Cederkäll, J; Courtin, S; Dessagne, P; Fraile-Prieto, L M; Franchoo, S; Fynbo, H O U; Huang Wan Xia; Jokinen, A; Knipper, A; Maréchal, F; Miehé, C; Nácher, E; Peräjärvi, K; Poirier, E; Weissman, L; Äystö, J

    2003-01-01

    The beta -decay of /sup 75/Sr to its mirror nucleus /sup 75/Rb was studied at the ISOLDE PSB facility at CERN by means of beta -delayed gamma and proton spectroscopy. The decay Q-value and beta -delayed gamma intensity were measured for the first time. These results, 10.60+or-0.22 MeV and 4.5/sub -0.7//sup +1.9/%, together with accurate measurements of the beta -decay half-life and beta -delayed proton branching ratio yielded the Gamow-Teller strength 0.35+or-0.05 for the mirror transition. Implications of the results on studies of deformation effects and on the path of the rapid proton capture process are discussed. (24 refs).

  7. Neodymium-doped Sr5(PO4)3F and Sr5(VO4)3F

    International Nuclear Information System (INIS)

    Corker, D.L.; Nicholls, J.; Loutts, G.B.

    1995-01-01

    Neodymium-doped Sr 5 (PO 4 ) 3 F [neodymium strontium fluoride phosphate, (Nd,Sr) 5 (PO 4 ) 3 F] and neodymium-doped Sr 5 (VO 4 ) 3 F [neodymium strontium fluoride vanadate, (Nd,Sr) 5 (VO 4 ) 3 F] crystallize in space group P6 3 /m and are isostructural with calcium fluorophosphate, Ca 5 (PO 4 ) 3 F. There are two different Sr sites in Sr 5 (XO 4 ) 3 F, denoted Sr(1) and Sr(2). Using single-crystal X-ray diffraction the two structures were refined to R factors of 2.3 and 2.2%, respectively, showing that Nd is present at both Sr sites in (Sr,Nd) 5 (VO 4 ) 3 F but only at the Sr(2) site in (Sr,Nd) 5 (PO 4 ) 3 F. (orig.)

  8. Distributions of 137Cs and 90Sr in the soil of Uljin, South Korea

    International Nuclear Information System (INIS)

    Song, Ji Yeon; Kim, Wan; Maeng, Seong Jin; Lee, Sang Hoon

    2016-01-01

    For the purpose of baseline data collection and enhancement of environmental monitoring the distribution studies of 137 Cs and 90 Sr in the soil of Uljin province was performed and the relation between surface soil activities and soil properties (pH, TOC and median of the surface soil) was analyzed. For 14 spots within 10 km from the NPP surface soil samples were collected and soils for depth profile were sampled for 3 spots in April 2011. Using γ-ray spectrometry with HPGe detector, the concentrations of 137 Cs were determined and the concentrations of 90 Sr were measured by counting β-activity of 90 Y (in equilibrium with 90 Sr) in a gas flow proportional counter. The concentration ranges of 137 Cs and 90 Sr were <0.479-39.6 Bq (kg-dry)-1 (avg. 7.51 Bq·(kg-dry)-1) and 0.209-1.85 Bq·(kg-dry)-1 (avg. 0.74 Bq·(kg-dry)-1) which were similar to the reported values from other regions in Korea. The activity ratio of 137 Cs to 90 Sr in surface soils was around 9.67, which is much bigger than the initial value of 1.75 for worldwide fallouts because of faster downward movement of 90 Sr after fall-out than that of 137 Cs. For depth profile studies soils were collected down to 40 cm depth for the locations of Deokgu, Hujeong and Maehwa. The 137 Cs concentration distribution of the first two showed maximum values at top soils and decreased rapidly in exponential manner, while 90 Sr showed two local maximum values for soils near top and about 30 cm depth. Through linear fittings between the 137 Cs and 90 Sr concentrations of surface soil and pH, TOC and median of the surface soil, the only probable relationship obtained was between 137 Cs and TOC (determination coefficient R2=0.6). The concentration ranges of 137 Cs and 90 Sr in Uljin were similar to the reported values from other regions in Korea. The only probable relationship obtained between activities and soil properties was between 137 Cs and TOC

  9. Distributions of {sup 137}Cs and {sup 90}Sr in the soil of Uljin, South Korea

    Energy Technology Data Exchange (ETDEWEB)

    Song, Ji Yeon; Kim, Wan; Maeng, Seong Jin; Lee, Sang Hoon [Kyungpook National University, Daegu (Korea, Republic of)

    2016-05-15

    For the purpose of baseline data collection and enhancement of environmental monitoring the distribution studies of {sup 137}Cs and {sup 90}Sr in the soil of Uljin province was performed and the relation between surface soil activities and soil properties (pH, TOC and median of the surface soil) was analyzed. For 14 spots within 10 km from the NPP surface soil samples were collected and soils for depth profile were sampled for 3 spots in April 2011. Using γ-ray spectrometry with HPGe detector, the concentrations of {sup 137}Cs were determined and the concentrations of {sup 90}Sr were measured by counting β-activity of {sup 90}Y (in equilibrium with {sup 90}Sr) in a gas flow proportional counter. The concentration ranges of {sup 137}Cs and {sup 90}Sr were <0.479-39.6 Bq (kg-dry)-1 (avg. 7.51 Bq·(kg-dry)-1) and 0.209-1.85 Bq·(kg-dry)-1 (avg. 0.74 Bq·(kg-dry)-1) which were similar to the reported values from other regions in Korea. The activity ratio of {sup 137}Cs to {sup 90}Sr in surface soils was around 9.67, which is much bigger than the initial value of 1.75 for worldwide fallouts because of faster downward movement of {sup 90}Sr after fall-out than that of {sup 137}Cs. For depth profile studies soils were collected down to 40 cm depth for the locations of Deokgu, Hujeong and Maehwa. The {sup 137}Cs concentration distribution of the first two showed maximum values at top soils and decreased rapidly in exponential manner, while {sup 90}Sr showed two local maximum values for soils near top and about 30 cm depth. Through linear fittings between the {sup 137}Cs and {sup 90}Sr concentrations of surface soil and pH, TOC and median of the surface soil, the only probable relationship obtained was between {sup 137}Cs and TOC (determination coefficient R2=0.6). The concentration ranges of {sup 137}Cs and {sup 90}Sr in Uljin were similar to the reported values from other regions in Korea. The only probable relationship obtained between activities and soil properties

  10. Proceedings of World Renewable Energy Congress '99

    International Nuclear Information System (INIS)

    Kamaruzzaman Sopian; Mohd Yusof Othman; Baharuddin Yatim

    2000-01-01

    The congress discussed the following subjects, 1. The role of renewable energy in the next millenium; 2. Challenges in the commercialization of renewable energy; 3. The role and agenda for renewable energy towards sustainable development. Topics covered in the technical session were biomass conversion; solar thermal technologies and systems; solar photovoltaic s; renewable energy economics, financing and policy; renewable energy education; climate and the environment; energy and architecture; energy management; wind and hydro technologies and systems; hydrogen and fuel cell

  11. Renewable Energy Policy Fact sheet - Romania

    International Nuclear Information System (INIS)

    2017-07-01

    The EurObserv'ER policy profiles give a snapshot of the renewable energy policy in the EU Member States. The promotion of renewable electricity in Romania relies primarily on a renewable quota scheme. Since 2017 the scheme has been closed for new projects. Renewable heating and cooling is promoted through investment subsidies. Renewable energy sources in the transport sector are promoted by a bio-fuels quota scheme and indirectly through a subsidy scheme for the purchase of electric vehicles

  12. Distribution of 127Cs and 90Sr in southern part of Pyajyanne lake and in its catchment area

    International Nuclear Information System (INIS)

    Saksen, R.; Rantavaara, A.; Yaakkola, T.

    1998-01-01

    Slight increase in 90 Sr content from river discharges was observed in the near-the-surface layers og the Asikkalanselk bay of the Pyajanne lake in the years directly following the Chernobyl accident; later it remained almost runchanged, whereas 137 Cs concentration is decreasing. 90 Sr was identified in the bottoms at greater depth than 137 Cs. Radionuclides transport by small rivers from water catchment zones to Asikkalanselsk was studied in 1995-1997. It is established that greater part of 137 Cs is leached into the surface waters from swamped areas. The swamped soils are also characterized by higher degree of 90 Sr washing out. The role of 137 Cs and 90 Sr surface discharges from catchment as compared to radionuclide exchange with other parts of the lake, containing greater water volumes

  13. Renewable energy policy and landscape management in Andalusia, Spain: The facts

    International Nuclear Information System (INIS)

    Prados, Maria-Jose

    2010-01-01

    Renewable energy has developed spectacularly in Spain since the European Union started a process of energy policy reform. A review of Spanish State legislation on renewable energies confirms that the success in installing renewable energy is attributable to public aid. Andalusia is one of the autonomous communities, which has simultaneously developed the legal framework and very successfully implemented the introduction of renewable power. When implementing the central government's policy, the Andalusian regional government prioritised increases in both surface cover by wind and solar plants (thermal and photovoltaic energy) and in the number of companies involved. However, this development of renewable energies took place without any proper integration into regional spatial and landscape planning. This paper explores renewable power implementation in Andalusia through regulatory measures put in place over the last decade to develop renewable energy systems and the way they can be managed alongside planning issues. The location of large-scale renewable plants has had consequences for territory in the socio-political context of renewable energy promotion. The main findings focus on renewable energy plant sprawl throughout rural areas in Andalusia with no clear effect on landscape management and no firm backing from the local population.

  14. Continuously renewed wall for a thermonuclear reactor

    International Nuclear Information System (INIS)

    Livshits, A.I.; Pustovojt, YU.M.; Samartsev, A.A.; Gosudarstvennyj Komitet po Ispol'zovaniyu Atomnoj Ehnergii SSSR, Moscow. Inst. Atomnoj Ehnergii)

    1982-01-01

    The possibility of creating a continuously renewed first wall of a thermonuclear reactor is experimentally investigated. The following variants of the wall are considered: the wall is double, its part turned to plasma is made of comparatively thin material. The external part separated from it by a small gap appears to be protected from interaction with plasma and performs structural functions. The gap contains the mixture of light helium and hydrogen and carbon-containing gas. The light gas transfers heat from internal part of the wall to the external part. Carbon-containing gas provides continuous renewal of carbon coating of the operating surface. The experiment is performed with palladium membrane 20 μm thick. Carbon is introduced into the membrane by benzol pyrolysis on one of the surfaces at the membrane temperature of 900 K. Carbon removal from the operating side of the wall due to its spraying by fast particles is modelled by chemical itching with oxygen given to the operating membrane wall. Observation of the carbon release on the operating surface is performed mass-spectrometrically according to the observation over O 2 transformation into CO and CO 2 . It is shown that in cases of benzol pressure of 5x10 -7 torr, carbon current on the opposite surface is not less than 3x10 12 atoms/sm 2 s and corresponds to the expected wall spraying rate in CF thermonuclear reactors. It is also shown that under definite conditions the formation and maintaining of a through protective carbon coating in the form of a monolayer or volumetric phase is possible

  15. Renewal and Change (Editorial

    Directory of Open Access Journals (Sweden)

    Denise Koufogiannakis

    2011-01-01

    Full Text Available The end of yet another calendar year leads to a time of new beginnings and new challenges. For me, this is the end of my three year term as Editor-in-Chief of EBLIP, which has been a very rewarding challenge personally and professionally. I would like to thank each and every person who has contributed to the success of the journal. EBLIP relies on the talented and professional people who regularly give of their time and expertise. I particularly want to thank the Editorial Team who has worked so closely with me over the past three years: Alison Brettle, Lorie Kloda, Katrine Mallan, Jonathan Eldredge, Michelle Dunaway, and our former intern Andrea Baer. Thank you!In the past three years, EBLIP has continued to grow and thrive. We currently have more than 3400 registered readers, and an Editorial Advisory Board comprised of 70 people from 11 countries. Several of our papers have had more than 5000 pdf downloads, and the average number of downloads is 1308. I am also pleased to let you know that we have recently been accepted for inclusion in Scopus.In looking back and reflecting on the past three years, we have continued to build a strong open access journal that is relevant to LIS practitioners. We have increased the number of articles being published, and the overall number of submissions. Content is wide ranging, including multiple sectors within library and information studies. Our evidence summaries continue to be the heart of our journal, with more and more research from our field being critically appraised in this way. We have also added new sections such as Using Evidence in Practice, in which authors reflect on incorporating evidence into practice.And now it is time yet again for renewal and change. I am very pleased to welcome Alison Brettle of the University of Salford, as she begins her three year term as Editor-in-Chief. Alison has been the Associate Editor (Articles since the very early days of publication and brings extensive

  16. MENA Renewables Status Report 2013

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-06-15

    The MENA Renewables Status Report is an outcome of ADIREC, the Abu Dhabi International Renewable Energy Conference. The report provides a status overview of renewable energy markets, industry, policy and investment trends in the region, drawing on the most recent data available. It is produced in cooperation with over 50 contributors and researchers in the region and reveals massive growth in the renewable energy markets of the Middle East and North Africa (MENA). Regional investment topped US$2.9 billion in 2012, up 40% from 2011 and 650% from 2004. With over 100 projects under development, the region could see a 450% increase in non-hydro renewable energy generating capacity in the next few years. For the report, the 21 MENA countries were clustered into two sub-groups: Net Oil-Exporting Countries (NOEC) -- Algeria, Bahrain, Egypt, Iran, Iraq, Kuwait, Libya, Oman, Qatar, Saudi Arabia, Syria, United Arab Emirates, and Yemen; and Net Oil-Importing Countries (NOIC) -- Djibouti, Israel, Jordan, Lebanon, Malta, Morocco, Palestine, and Tunisia.

  17. Adsorption of Sr(II) and Eu(III) on Na-rectorite. Effect of pH, ionic strength, concentration and modelling

    Energy Technology Data Exchange (ETDEWEB)

    Hu, J.; Wang, X.K. [School of Nuclear Science and Engineering, North China Electric Power Univ., BJ (China); Key Lab. of Novel Thin Film Solar Cells, Inst. of Plasma Physics, Chinese Academy of Sciences, Hefei (China); Chen, C.L.; Sheng, G.D.; Li, J.X. [Key Lab. of Novel Thin Film Solar Cells, Inst. of Plasma Physics, Chinese Academy of Sciences, Hefei (China); Chen, Y.X. [School of Nuclear Science and Engineering, North China Electric Power Univ., BJ (China)

    2010-07-01

    The surface charge characteristics of Na-rectorite (NaAl{sub 4}[Si,Al]{sub 8}O{sub 20}(OH){sub 4}.nH{sub 2}O;) were studied by potentiometric acid-base titrations. Sr(II) and Eu(III) adsorptions on Na-rectorite as a function of pH, ionic strength, and Sr(II)/Eu(III) concentrations were carried out to investigate the surface interactions between Sr(II)/Eu(III) with Na-rectorite. The results indicated that the adsorptions of Sr(II) and Eu(III) on Na-rectorite increased with increasing pH and decreased with increasing ionic strength and initial Sr(II)/Eu(III) concentrations, and that the affinity of Na-rectorite for Eu(III) was much higher than for Sr(II). The experimental data of Sr(II)/Eu(III) adsorption were simulated by the diffuse-layer model (DLM) well with the aid of FITEQL 3.2. Simultaneous adsorptions of Sr(II) and Eu(III) on Na-rectorite were also modeled using the DLM. The adsorption mechanisms of Sr(II) and Eu(III) on Na-rectorite may be dominated by ion exchange interaction at low pH or moderate pH, and by surface complexation interaction at high pH. (orig.)

  18. Autoradiography of 90Sr in developing rats

    International Nuclear Information System (INIS)

    Olsen, I.; Jonsen, J.

    1979-01-01

    The distribution patterns of 90 Sr in five littermate, 8-day-old Wistar rats were studied by whole body autoradiography. Rats were killed 15 min, 1, 4, 24, and 72 h after a single intraperitoneal injection of the isotope. Immediately after administration, 90 Sr was distributed throughout most of the soft tissues of the body. The soft tissue deposits had practically disappeared after 4 h. In the hard tissues of the body 90 Sr accumulated up to 24-72 h. Fifteen minutes after injection the uptake of 90 Sr in the enamel of the teeth was highest in the occlusal and incisal regions. 90 Sr gradually accumulated throughout the enamel and after 72 h its distribution in this layer was fairly uniform. Immediately after injection a narrow zone of radioactivity appeared in the dentin near the pulp. This zone broadened with time towards the dentinoenamel junction and included the intire dentin layer 72 h after injection. Initially, the uptake of 90 Sr was higher in the dentin than in the enamel, particularly in the cervical areas of the crown. This difference became less apparent with time. There was good correlation between the uptake in the teeth and bones, supporting the use of teeth as indicators of the 90 Sr body burden. (author)

  19. Maxdose-SR and popdose-SR routine release atmospheric dose models used at SRS

    Energy Technology Data Exchange (ETDEWEB)

    Jannik, G. T. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Trimor, P. P. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2017-07-28

    MAXDOSE-SR and POPDOSE-SR are used to calculate dose to the offsite Reference Person and to the surrounding Savannah River Site (SRS) population respectively following routine releases of atmospheric radioactivity. These models are currently accessed through the Dose Model Version 2014 graphical user interface (GUI). MAXDOSE-SR and POPDOSE-SR are personal computer (PC) versions of MAXIGASP and POPGASP, which both resided on the SRS IBM Mainframe. These two codes follow U.S. Nuclear Regulatory Commission (USNRC) Regulatory Guides 1.109 and 1.111 (1977a, 1977b). The basis for MAXDOSE-SR and POPDOSE-SR are USNRC developed codes XOQDOQ (Sagendorf et. al 1982) and GASPAR (Eckerman et. al 1980). Both of these codes have previously been verified for use at SRS (Simpkins 1999 and 2000). The revisions incorporated into MAXDOSE-SR and POPDOSE-SR Version 2014 (hereafter referred to as MAXDOSE-SR and POPDOSE-SR unless otherwise noted) were made per Computer Program Modification Tracker (CPMT) number Q-CMT-A-00016 (Appendix D). Version 2014 was verified for use at SRS in Dixon (2014).

  20. Optimization of control parameters for SR in EDM injection flushing type on stainless steel 304 workpiece

    International Nuclear Information System (INIS)

    Reza, M S; Yusoff, A R; Shaharun, M A

    2012-01-01

    The operating control parameters of injection flushing type of electrical discharge machining process on stainless steel 304 workpiece with copper tools are being optimized according to its individual machining characteristic i.e. surface roughness (SR). Higher SR during EDM machining process results for poor surface integrity of the workpiece. Hence, the quality characteristic for SR is set to lower-the-better to achieve the optimum surface integrity. Taguchi method has been used for the construction, layout and analysis of the experiment for each of the machining characteristic for the SR. The use of Taguchi method in the experiment saves a lot of time and cost of machining the experiment samples. Therefore, an L18 Orthogonal array which was the fundamental component in the statistical design of experiments has been used to plan the experiments and Analysis of Variance (ANOVA) is used to determine the optimum machining parameters for this machining characteristic. The control parameters selected for this optimization experiments are polarity, pulse on duration, discharge current, discharge voltage, machining depth, machining diameter and dielectric liquid pressure. The result had shown that the lower the machining diameter, the lower will be the SR.

  1. Contributions of conduction band offset to the enhanced separation efficiency of photoinduced charges for SrTiO3/Bi2O3 heterojunction semiconductor

    International Nuclear Information System (INIS)

    Zhang, Zhenlong; Zhu, Jichun; Li, Shengjun; Mao, Yanli

    2014-01-01

    SrTiO 3 /Bi 2 O 3 heterojunction semiconductor was prepared and characterized by X-ray diffraction, UV–vis absorption spectrum, and scanning electron microscope, surface photovoltage spectroscopy, and photoluminescence spectroscopy. The surface photovoltage spectra indicate that the separation efficiency of photoinduced charges for SrTiO 3 /Bi 2 O 3 was enhanced compared with that of SrTiO 3 or Bi 2 O 3 . The energy band diagram of SrTiO 3 /Bi 2 O 3 heterojunction was directly determined with X-ray photoelectron spectroscopy, and the conduction band offset between SrTiO 3 and Bi 2 O 3 was quantified to be 0.28±0.03 eV. The photoluminescence spectra display that the recombination rate of photoinduced carriers for SrTiO 3 /Bi 2 O 3 decreases compared with that of SrTiO 3 or Bi 2 O 3 , which is mainly due to the energy levels matching between them. Therefore the enhanced separation efficiency of photoinduced charges is resulting from the energy difference between the conduction band edges of SrTiO 3 and Bi 2 O 3 . -- Graphical abstract: Enhanced separation efficiency for SrTiO 3 /Bi 2 O 3 is resulting from the energy difference between the conduction band edges. Highlights: ●Heterojunction semiconductor of SrTiO 3 /Bi 2 O 3 was prepared. ●SrTiO 3 /Bi 2 O 3 presents enhanced separation efficiency. ●Conduction band offset between SrTiO 3 and Bi 2 O 3 is quantified. ●Recombination rate of SrTiO 3 /Bi 2 O 3 decreases compared with single phases

  2. Introduction to Renewable Energy Systems

    DEFF Research Database (Denmark)

    Ma, Ke; Yang, Yongheng; Blaabjerg, Frede

    2014-01-01

    . It is concluded that as the quick development of renewable energy, wind power and PV power both show great potential to be largely integrated into the power grid. Power electronics is playing essential role in both of the systems to achieve more controllable, efficient, and reliable energy production......In this chapter, the state-of-the-arts developments of renewable energy are reviewed in respect to the installed power and market share, where wind power and photovoltaic power generation are the main focuses due to the fast growing speed and large share of installed capacity. Some basic principles...... of operation, mission profiles, as well as power electronics solutions and corresponding controls are discussed respectively in the case of wind power and photovoltaic power systems. Finally a few development trends for renewable energy conversions are also given from a power electronics point of view...

  3. Renewable Energy CSOPs in Germany

    Directory of Open Access Journals (Sweden)

    Jens Lowitzsch

    2013-01-01

    Full Text Available The Energy-CSOP facilitates broad equity participation of citizens without assets or savings in a regulated public energy utility. As the CSOP is designed for regulated markets with guaranteed prices, regulated market access and long-term relationships between producer and consumer, the energy market is predestined. A CSOP trust can be set up for a renewable energy plant (e.g., a biogas reactor, a solar panel, a windmill or a geothermic drill. European states have set an ambitious target to reach 20% share of energy from renewable sources by 2020. Germany as Europe’s green energy leader could become a pioneer in CSOP implementation. Small communities in Europe would benefit from the increased share of renewable energy resources.

  4. Renewable Energy Devices and Systems

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Ionel, Dan M.

    2015-01-01

    In this paper, essential statistics demonstrating the increasing role of renewable energy generation are firstly discussed. A state of the art review section covers fundamentals of wind turbines and PV systems. Included are schematic diagrams illustrating the main components and system topologies...... and the fundamental and increasing role of power electronics as an enabler for renewable energy integration, and for the future power system and smart grid. Recent examples of research and development, including new devices and system installations for utility power plants, as well for as residential and commercial......, fuel cells, and storage with batteries and hydrogen, respectively. Recommended further readings on topics of electric power engineering for renewable energy are included in a final section. This paper also represents an editorial introduction for two special issues of the Electric Power Component...

  5. Renewable energy market overview 2000

    International Nuclear Information System (INIS)

    Mahoney, Nicholas

    2001-01-01

    The article discusses the findings of a recent survey on the renewable energy market carried out in 164 countries and across a wide range of sectors of industry. The survey found almost unanimous optimism regarding the growth of the renewable energy market over the coming year. Tables show (i) the survey sample (in terms of continents, database population and responses); (ii) subsidiaries and locations of parent companies; (iii) expectations of sales next year (by continent) and (iv) expectations of sales in the coming year by sector. Figures show (a) regional distribution of companies (by continent); (b) companies' activities and (c) index of expectations of sales, by continent. The survey is intended for inclusion in the World Directory of Renewable Energy Suppliers and Services

  6. Project financing renewable energy schemes

    International Nuclear Information System (INIS)

    Brandler, A.

    1993-01-01

    The viability of many Renewable Energy projects is critically dependent upon the ability of these projects to secure the necessary financing on acceptable terms. The principal objective of the study was to provide an overview to project developers of project financing techniques and the conditions under which project finance for Renewable Energy schemes could be raised, focussing on the potential sources of finance, the typical project financing structures that could be utilised for Renewable Energy schemes and the risk/return and security requirements of lenders, investors and other potential sources of financing. A second objective is to describe the appropriate strategy and tactics for developers to adopt in approaching the financing markets for such projects. (author)

  7. Renewable energy market overview 2000

    Energy Technology Data Exchange (ETDEWEB)

    Mahoney, Nicholas

    2001-02-01

    The article discusses the findings of a recent survey on the renewable energy market carried out in 164 countries and across a wide range of sectors of industry. The survey found almost unanimous optimism regarding the growth of the renewable energy market over the coming year. Tables show (i) the survey sample (in terms of continents, database population and responses); (ii) subsidiaries and locations of parent companies; (iii) expectations of sales next year (by continent) and (iv) expectations of sales in the coming year by sector. Figures show (a) regional distribution of companies (by continent); (b) companies' activities and (c) index of expectations of sales, by continent. The survey is intended for inclusion in the World Directory of Renewable Energy Suppliers and Services.

  8. Renewable energies. Italy is mobilizing

    International Nuclear Information System (INIS)

    Marante, W.

    2005-01-01

    About 3 quarter of the Italian electric power comes from fossil fuel power plants. The rest is generated from hydropower, few comes from biomass and wind energy and a very few from geothermal energy (2% of the national production). However, the situation is changing and geothermal energy, with only 5 TWh, makes Italy the European leader in this domain and the world number 4 behind USA, Philippines and Mexico. The renewable sources represent 18.5% of the total Italian energy production. During the last five years, the renewable energy sources have developed rapidly: +80% per year for the wind energy, +32% per year for biomass and about +3% per year for geothermal energy. Moreover, the Italian government is implementing incentives for the development of renewable energy sources. This article gives an overview of the situation. (J.S.)

  9. Report on nuclear energy in SR Slovenia

    International Nuclear Information System (INIS)

    1987-01-01

    Currently Yugoslavia has one 632 MWe nuclear power plant (NPP) of PWR design, located at Krsko in the Socialist Republic (SR) of Slovenia. Krsko NPP, which is a two-loop plant, started power operation in 1981. In general, reactor safety activities in the SR of Slovenia are mostly related to upgrading the safety of our Krsko NPP and to developing capabilities for use in future units. This report presents the nuclear safety related legislation and organization of the corresponding regulatory body, and the activities related to nuclear safety of the participating organizations in the SR of Slovenia in 1987.

  10. Beta dosimetry in teeth from SR-90 exposed subjects

    International Nuclear Information System (INIS)

    Fattibene, P.; De Coste, V.; Onori, S.; Veronese, I.; Giussani, A.; Cantone, M.C.; Shishkina, E.

    2006-01-01

    Tooth enamel is a well recognized dosimeter for retrospective dose reconstruction of individuals accidentally exposed to ionizing radiation. The measurements of the absorbed dose in tooth enamel is conventionally carried out with the Electron Paramagnetic Resonance technique. Tooth enamel is sensitive to all kind of ionizing radiation. Its response to photons has been widely investigated. For application to contaminated teeth with 90 Sr, one of the most common osteo tropic radionuclides, the effectiveness of tooth enamel response to the β spectrum needs be evaluated. The response function to 90 Sr of the EPR/tooth enamel systems, its linearity and reproducibility have been investigated under a controlled geometry, and the results will be presented and compared to those obtained with photons. When the subject has been exposed to both external and internal radiation, a combined EPR/T.L. method can be used to distinguish the internal from the external contribution to the cumulative dose in tooth (Gosku et al., 2002;=Veronese et al. 2004, Shishkina et al. 2005). The T.L. measurement, performed putting thin ± Al 2 O 3 :C dosimeters at contact with the tooth surfaces, enables to estimate the beta dose rate due to the radionuclides present in tooth. The combination of this information with that coming from EPR allows, under specific assumptions, to evaluate separately the internal and external contribution to the tooth dose. In a previous work (Veronese et al., 2004) the dose in enamel measured by EPR in a tooth contaminated with 90 Sr of a Techa River resident was compared to the dose rate measured by TLDs. The test has been extended to a larger number of 90 Sr contaminated teeth. EPR measurements have been also performed in other portions of the teeth, i.e. tooth dentin and root. The correlation between the results, obtained from EPR and TLD measurements, and the evaluation of the relative proportion of internal and external dose are presented and discussed. (authors)

  11. China's renewable energy policy: Commitments and challenges

    International Nuclear Information System (INIS)

    Wang Feng; Yin Haitao; Li Shoude

    2010-01-01

    The passing of the Renewable Energy Law (REL) in 2005 demonstrated China's commitment to renewable energy development. In the 3 years after the REL, China's renewable electricity capacity grew rapidly. From 2006 to 2008, China's wind capacity installation more than doubled every year for 3 years in a row. However, three facts prevent us from being optimistic about China's renewable electricity future. First, considered as a share of total capacity, renewable electricity capacity is decreasing instead of increasing. This is due simply to the rapid growth of fossil fuel capacity. Second, a significant amount of renewable generation capacity is wasted because it is not connected to the electricity grid. Finally, renewable electricity plants are running at a low level of efficiency. Based on an in-depth analysis of China's existing renewable energy policy, we suggest that these challenges should be dealt with by introducing a market-based mandatory renewable portfolio requirement coupled with strong regulatory monitoring of grid enterprises.

  12. Renewable energy technology acceptance in Peninsular Malaysia

    International Nuclear Information System (INIS)

    Kardooni, Roozbeh; Yusoff, Sumiani Binti; Kari, Fatimah Binti

    2016-01-01

    Despite various policies, renewable energy resources have not been developed in Malaysia. This study investigates the factors that influence renewable energy technology acceptance in Peninsular Malaysia and attempts to show the impact of cost and knowledge on the perceived ease of use and perceived usefulness of renewable energy technology. The results show that cost of renewable energy has an indirect effect on attitudes towards using renewable energy through the associated impact on the perceived ease of use and perceived usefulness. The results also indicate that public knowledge in Peninsular Malaysia does not affect perceived ease of use, although the positive impact of knowledge on perceived usefulness is supported. Furthermore, our results show that the current business environment in Peninsular Malaysia does not support the adoption of renewable energy technology, and thus, renewable energy technology is not commercially viable in Peninsular Malaysia. Additionally, the population of Peninsular Malaysia associates the use of renewable energy with a high level of effort and therefore has a negative attitude towards the use of renewable energy technology. There is, therefore, a definite need to pay more attention to the role of public perception and awareness in the successes and failures of renewable energy policy. - Highlights: • Public acceptance is an essential element in the diffusion of renewable energy. • Perceived ease of use and perceived usefulness affect intention to use renewables. • It is important to reduce the cost of renewable energy, particularly for end users. • Renewable energy policies should address issues of public perception and awareness.

  13. World potential of renewable energies

    Energy Technology Data Exchange (ETDEWEB)

    Dessus, B; Devin, B; Pharabod, F

    1991-07-01

    A comprehensive analysis, region by region, of the actually accessible renewable energies at a given horizon, is presented. The same methodology as the one employed to derive ``proven fossil energy reserves`` from ``energy resources`` is adopted, in which resources are defined by quantitative information on physical potential, while reserves take into account technical and economical accessibility. As renewable resources are fluctuating with time and are diluted in space and not readily transportable or storeable, it is necessary to consider the presence of populations or activities near enough to be able to profit by these diluted and volatile energies.

  14. Renewables 2012. Global Status Report

    Energy Technology Data Exchange (ETDEWEB)

    Sawin, J. L. [and others

    2012-08-15

    Renewable energy markets and policy frameworks have evolved rapidly in recent years. This report provides a comprehensive and timely overview of renewable energy market, industry, investment, and policy developments worldwide. It relies on the most recent data available, provided by a network of more than 400 contributors and researchers from around the world, all of which is brought together by a multi-disciplinary authoring team. The report covers recent developments, current status, and key trends; by design, it does not provide analysis or forecast the future.

  15. Renewable energy prospects for implementation

    CERN Document Server

    Jackson, Tim

    1993-01-01

    Renewable Energy: Prospects for Implementation contains papers that were originally commissioned by the journal Energy Policy for a series on renewable energy appearing between January 1991 to September 1992. In view of the fast-changing demands on conventional energy supply to meet environmental imperatives, it seemed timely to reproduce here a selection of those papers with a new introduction and a revised concluding chapter by the Editor of the series, Dr Tim Jackson, a research fellow with the Stockholm Environment Institute. The book is organized into four parts. The papers in Part I

  16. Renewable energy sources. Erneuerbare Energien

    Energy Technology Data Exchange (ETDEWEB)

    1988-01-01

    To judge future trends in work on the exploitation of renewable energy sources for overall energy supply, it is necessary to know the following: the rules that nature abides by, the principles of technical exploitation of these energies, and the basic data for the current state of development. The above information is compiled in this publication for those renewable energy sources on which topical discussion centres: solar radiation and wind. For the remaining renowable energy sources (e.g. biomass, tidal power, geothermal energy), some examples of use are mentioned and advanced literature is indicated. (orig./HSCH).

  17. Renewable energies: the Spanish assets

    International Nuclear Information System (INIS)

    Petit-Pez, Ch.; Molenat, G.

    2009-01-01

    Even though Spain is far away from the Kyoto protocol objectives, this country possesses numerous assets in terms of renewable energies. This report presents overviews of the present situation and of innovation and research activities in the different fields of renewable energies: wind energy, solar energy (thermal, thermoelectric and photovoltaic), hydraulic energy (dams, tide and wave energy), biomass (wood, bio-fuels, biogas). Along with these presentations, the authors propose tables and graphs of quantitative data concerning these different energy productions, at the national as well as at the regional level, with comparison with data for other European countries

  18. Renewable energies - Situation and perspectives

    International Nuclear Information System (INIS)

    Acket, Claude; Vaillant, Jacques

    2011-01-01

    The world has to face increasing energy needs while it is today dependent of fossil fuels at 80%. Getting out of the fossil fuels dependence model requires an important effort to promote the energy saving and the carbon-free energies as well, and in particular the renewable energy sources. Taking all this information into account, the authors evaluate the global share that renewable energies could represent in the energy mix, in France and in the entire world. This share represents today only 10% of the energy consumed, but will it remain marginal or will it become important and eventually prominent? (J.S.)

  19. Comment: The Economics of Interdependent Renewable and Non-renewable Resources revisited.

    OpenAIRE

    Viktoria Kahui; Claire W. Armstrong

    2009-01-01

    This work expands upon Swallow's theoretical analysis of interactions between renewable and non-renewable resources. In this comment the interaction is such that the renewable resource prefers the non-renewable environment, as opposed to SwallowÕs (op cit) case of the non-renewable environment being essential to the renewable resource. We find that this difference strongly affects the results, and makes the resources change from being complements to being substitutes, i.e. in the essential ca...

  20. Equilibrium Transitions from Non Renewable Energy to Renewable Energy under Capacity Constraints

    OpenAIRE

    Amigues, Jean-Pierre; Ayong Le Kama, Alain; Moreaux, Michel

    2013-01-01

    We study the transition between non-renewable and renewable energy sources with adjustment costs over the production capacity of renewable energy. Assuming constant variable marginal costs for both energy sources, convex adjustment costs and a more expensive renewable energy, we show the following. With sufficiently abundant non-renewable energy endowments, the dynamic equilibrium path is composed of a first time phase of only non-renewable energy use followed by a transition phase substituti...

  1. 90Sr specific activity of teeth of abandoned cattle after the Fukushima accident - teeth as an indicator of environmental pollution.

    Science.gov (United States)

    Koarai, Kazuma; Kino, Yasushi; Takahashi, Atsushi; Suzuki, Toshihiko; Shimizu, Yoshinaka; Chiba, Mirei; Osaka, Ken; Sasaki, Keiichi; Urushihara, Yusuke; Fukuda, Tomokazu; Isogai, Emiko; Yamashiro, Hideaki; Oka, Toshitaka; Sekine, Tsutomu; Fukumoto, Manabu; Shinoda, Hisashi

    2018-03-01

    90 Sr specific activity in the teeth of young cattle that were abandoned in Kawauchi village and Okuma town located in the former evacuation areas of the Fukushima-Daiichi Nuclear Power Plant (FNPP) accident were measured. Additionally, specific activity in contaminated surface soils sampled from the same area was measured. (1) All cattle teeth examined were contaminated with 90 Sr. The specific activity, however, varied depending on the developmental stage of the teeth during the FNPP accident; teeth that had started development before the accident exhibited comparatively lower values, while teeth developed mainly after the accident showed higher values. (2) Values of 90 Sr-specific activity in teeth formed after the FNPP accident were higher than those of the bulk soil but similar to those in the exchangeable fraction (water and CH 3 COONH 4 soluble fractions) of the soil. The findings suggest that 90 Sr was incorporated into the teeth during the process of development, and that 90 Sr in the soluble and/or leachable fractions of the soil might migrate into teeth and contribute to the amount of 90 Sr in the teeth. Thus, the concentration of 90 Sr in teeth formed after the FNPP accident might reflect the extent of 90 Sr pollution in the environment. Copyright © 2017 Elsevier Ltd. All rights reserved.

  2. Migration of 90Sr in the cooling basin of the Ignalina atomic power plant and the Baltic sea ecosystems

    International Nuclear Information System (INIS)

    Dushauskiene-Duzh, R.

    1992-01-01

    On the basis of a long-time radiation monitoring of the Ignalina APP and the Baltic sea ecosystems determined regularities of the 90 Sr distribution in the main components of the ecosystems (water, bottom sediments, biota). It was established that 90 Sr accumulation coefficient in the aquatic plants of the warmed up water zone of the Ignalina APP is 2.6 lower than that of the stable water suction zone. The accumulation of 90 Sr in molluscs is higher in the warmed up water zone than in the stable water zone. It was determined that the mean concentration of 90 Sr in surface water of near-shore areas of the Baltic sea are higher than that in the open Baltic. Concentration of the 90 Sr in the biota in the Baltic sea is about 300-500 times higher than in the water. The accumulation level of 90 Sr in zoobenthos varies in different species being in organs and tissues of fishes consuming actively calcium for building up their skeletons. 90 Sr levels in bottom sediments of bays are higher than those in sediments of the open sea. Accumulation of 90 Sr in muds is about 11 times higher than in sands. (author). 5 figs., 3 refs

  3. The renewable energy field is gaining power

    Energy Technology Data Exchange (ETDEWEB)

    Fuller, D.B.

    1984-01-01

    For about 25 years, Basic Resources Corp. in New York has been growing on the strength of operations ranging from oil and gas exploration and printing to computer leasing and the manufacture of highway toll-collecting equipment. But since early 1982, when it received an Energy Department grant, a new subsidiary has been working on a project with scant resemblance to any other of the multimillion-dollar firm's operations: the preliminary research for an ocean thermal energy plant that would convert heat on the ocean's surface to power at a site in the Hawaiian islands. Renewable energy -- once largely the domain of dreamers and urban dropouts -- has moved into the corporate mainstream, and more and more companies in the United States and abroad are trying to stake a claim to a piece of its future. Basic Resources is not the only renewable energy source firm doing well. Several hundred exhibitors and other participants -- including a number of foreign visitors -- turned out for the 3-day event. Arco, which has been working on photovoltaics since the late 1970s, is considered the world's largest manufacturer of photovoltaics -- solar cells that convert the sun's energy directly into electricity. But, despite tax credits, worldwide sales and dramatic strides in reducing the cost of the technology, the operation still isn't profitable after the costs of research and other costreduction efforts are included. Nonetheless, Arco has no plans to abandon the field, and its attitude explains why so many firms are bucking the odds and pursuing renewable energy.

  4. Comparison study of different coatings on degradation performance and cell response of Mg-Sr alloy

    Energy Technology Data Exchange (ETDEWEB)

    Shangguan, Yongming [Department of Materials Science and Engineering, Nanjing University of Science and Technology, Nanjing 210094 (China); Institute of Metal Research, Chinese Academy of Sciences, 72 Wenhua Road, Shenyang 110016 (China); Sun, Lina [Jinzhou Medical University, Jinzhou 121000 (China); Wan, Peng, E-mail: pwan@imr.ac.cn [Institute of Metal Research, Chinese Academy of Sciences, 72 Wenhua Road, Shenyang 110016 (China); Department of Orthopaedics and Traumatology, The Chinese University of Hong Kong, Hong Kong SAR (China); Tan, Lili [Institute of Metal Research, Chinese Academy of Sciences, 72 Wenhua Road, Shenyang 110016 (China); Wang, Chengyue [Jinzhou Medical University, Jinzhou 121000 (China); Fan, Xinmin [Department of Materials Science and Engineering, Nanjing University of Science and Technology, Nanjing 210094 (China); Qin, Ling [Department of Orthopaedics and Traumatology, The Chinese University of Hong Kong, Hong Kong SAR (China); Yang, Ke, E-mail: kyang@imr.ac.cn [Institute of Metal Research, Chinese Academy of Sciences, 72 Wenhua Road, Shenyang 110016 (China)

    2016-12-01

    To solve the problem of rapid degradation for magnesium-based implants, surface modification especially coating method is widely studied and showed the great potential for clinical application. However, as concerned to the further application and medical translation for biodegradable magnesium alloys, there are still lack of data and comparisons among different coatings on their degradation and biological properties. This work studied three commonly used coatings on Mg-Sr alloy, including micro-arc oxidation coating, electrodeposition coating and chemical conversion coating, and compared these coatings for requirements of favorable degradation and biological performances, how each of these coating systems has performed. Finally the mechanism for the discrepancy between these coatings is proposed. The results indicate that the micro-arc oxidation coating on Mg-Sr alloy exhibited the best corrosion resistance and cell response among these coatings, and is proved to be more suitable for the orthopedic application. - Highlights: • The MAO, PED and Sr-P coating were fabricated on Mg-Sr alloy to evaluate the degradation. • The MAO coating showed the greatest degradation performance among these three coatings. • The PED coating exhibited worse corrosion resistance even than Mg-Sr substrate. • The value of cell proliferation and ALP activity were ranked in the following order: MAO > Sr-P > PED.

  5. Comparison study of different coatings on degradation performance and cell response of Mg-Sr alloy

    International Nuclear Information System (INIS)

    Shangguan, Yongming; Sun, Lina; Wan, Peng; Tan, Lili; Wang, Chengyue; Fan, Xinmin; Qin, Ling; Yang, Ke

    2016-01-01

    To solve the problem of rapid degradation for magnesium-based implants, surface modification especially coating method is widely studied and showed the great potential for clinical application. However, as concerned to the further application and medical translation for biodegradable magnesium alloys, there are still lack of data and comparisons among different coatings on their degradation and biological properties. This work studied three commonly used coatings on Mg-Sr alloy, including micro-arc oxidation coating, electrodeposition coating and chemical conversion coating, and compared these coatings for requirements of favorable degradation and biological performances, how each of these coating systems has performed. Finally the mechanism for the discrepancy between these coatings is proposed. The results indicate that the micro-arc oxidation coating on Mg-Sr alloy exhibited the best corrosion resistance and cell response among these coatings, and is proved to be more suitable for the orthopedic application. - Highlights: • The MAO, PED and Sr-P coating were fabricated on Mg-Sr alloy to evaluate the degradation. • The MAO coating showed the greatest degradation performance among these three coatings. • The PED coating exhibited worse corrosion resistance even than Mg-Sr substrate. • The value of cell proliferation and ALP activity were ranked in the following order: MAO > Sr-P > PED.

  6. Distribution of {sup 90}Sr activities in the environmental radiation samples of Jeju Island, Korea

    Energy Technology Data Exchange (ETDEWEB)

    Han, Chung Hun; Park, Youn Hyun; Lee, Young Gyu; Park, Jae Woo [Jeju National University, Jeju (Korea, Republic of)

    2016-12-15

    This work was to get information about {sup 90}Sr contamination of the environment by using soil and moss from selected areas in Jeju Island, Korea. The activities of {sup 90}Sr in soil and moss samples were investigated at nine locations of Jeju island, Korea. The soil samples have been collected at 4 sites of Jeju island during June to August of 2013, analyzed for vertical distribution of {sup 90}Sr activities. The moss samples have been collected at 5 sites of Jeju island during November of 2011 to June of 2012, and analyzed for radioactive {sup 90}Sr. The {sup 90}Sr vertical concentrations in the investigated soil samples were 2.77 to 18.24 Bq·kg{sup -1} in eastern part, 1.69 to 18.27 Bq·kg{sup -1} in northern part, 3.76 to 13.46 Bq·kg{sup -1} in the western part and 1.09 to 8.70 Bq·kg{sup -1} in the southern part of the Mt. Halla in Jeju island, respectively. Activities of {sup 90}Sr show the highest value at the surface soil and decrease with depth. The activity concentration measured was in the range of 79.6 to 363 Bq·kg{sup -1} -dry moss. This material is expected to be basis reference for survey of environmental radioactivity in Jeju Island.

  7. Ag loading induced visible light photocatalytic activity for pervoskite SrTiO3 nanofibers

    Science.gov (United States)

    Wu, Yeqiu; He, Tao

    2018-06-01

    The synthesis and photocatalytic activities of Ag-SrTiO3 nanofibers were reported in this work. The fabricated Ag-SrTiO3 nanofibers were characterized by TG-DSC, XRD, IR, XPS, SEM, TEM, DRS and ESR techniques. The XRD and IR results show that Ag-SrTiO3 nanofibers have a perovskite structure after the heat treatment at 700 °C. The XPS result shows that Ag element exists as Ag0 in the fabricated Ag-SrTiO3 nanofibers. The SEM and TEM images indicate the obtaining of nanofibers with porous structure. The photocatalytic activity of Ag-SrTiO3 nanofibers was evaluated by degrading RhB and MB under visible light irradiation. The Ag-SrTiO3 nanofibers show excellent photocatalytic activity under visible light irradiation because of the surface plasmon resonance effect of Ag0. In the photocatalysis process of RhB and MB, lots of hydroxyl radicals were generated, which plays the key role in the decomposition of organic pollutants.

  8. Alaska's renewable energy potential.

    Energy Technology Data Exchange (ETDEWEB)

    2009-02-01

    This paper delivers a brief survey of renewable energy technologies applicable to Alaska's climate, latitude, geography, and geology. We first identify Alaska's natural renewable energy resources and which renewable energy technologies would be most productive. e survey the current state of renewable energy technologies and research efforts within the U.S. and, where appropriate, internationally. We also present information on the current state of Alaska's renewable energy assets, incentives, and commercial enterprises. Finally, we escribe places where research efforts at Sandia National Laboratories could assist the state of Alaska with its renewable energy technology investment efforts.

  9. Renewable energy policy. Into the mainstream

    International Nuclear Information System (INIS)

    2003-01-01

    Renewable energy today is at a critical stage of development: renewable technologies are maturing, and costs for some technologies are in the competitive range. Beyond the energy they produce, renewable energy technologies offer a variety of other benefits towards the achievement of sustainable development goals. This promise has led to all IEA governments to support their greater development. But, while renewables markets are growing strongly, additional steps must be taken to accelerate the achievement of sustainable, large-scale markets. This report by the IEA's Renewable Energy Working Party outlines those steps, and the benefits of moving renewable energy into the mainstream

  10. Ion microprobe Sr isotope analysis of carbonates with about 5 {mu}m spatial resolution: An example from an ayu otolith

    Energy Technology Data Exchange (ETDEWEB)

    Sano, Yuji [Center for Advanced Marine Research, Ocean Research Institute, University of Tokyo, Nakano-ku, Tokyo 164-8639 (Japan)], E-mail: ysano@ori.u-tokyo.ac.jp; Shirai, Kotaro [International Coastal Research Center, Ocean Research Institute, University of Tokyo, Otsuchi, Iwate 028-1102 (Japan); Takahata, Naoto; Amakawa, Hiroshi [Center for Advanced Marine Research, Ocean Research Institute, University of Tokyo, Nakano-ku, Tokyo 164-8639 (Japan); Otake, Tsuguo [International Coastal Research Center, Ocean Research Institute, University of Tokyo, Otsuchi, Iwate 028-1102 (Japan)

    2008-08-15

    A high lateral resolution secondary ion mass spectrometer (NanoSIMS NS50 ion microprobe) has been used to measure {sup 87}Sr/{sup 86}Sr ratios in natural CaCO{sub 3} samples. A {approx}2 nA O{sup -} primary beam was used to sputter a 5-7-{mu}m diameter crater on the sample surface and secondary positive ions were extracted for mass analysis using an accelerating voltage of 8 kV and a Mattauch-Herzog geometry. The multi-collector system was adjusted to detect {sup 43}Ca{sup +} (by a detector EM2), {sup 80}Ca{sub 2}{sup +} (EM3), {sup 86}Sr{sup +} (EM4), and {sup 87}Sr{sup +} (EM4b) ions at the same time. Then the magnetic field was scanned for the EM4 to detect {sup 85}Rb{sup +}, {sup 86}Sr{sup +} and {sup 87}Sr{sup +}, while the EM4b can measure {sup 86}Sr{sup +}, {sup 87}Sr{sup +} and {sup 88}Sr{sup +}, respectively. A mass resolution of 3600 at 10% peak height was attained with a flat peak top, while the sensitivity of Sr was about 10 cps/nA/ppm. An aragonite sample (coral skeleton standard; JCp-1) was used as a reference for Sr isotope ratio calibration. Repeated analyses of the JCp-1 show that the {sup 87}Sr/{sup 86}Sr ratio agrees well with the seawater signature within a precision of 0.3 per mille at 2{sigma}, after the series of corrections such as the Ca dimer, {sup 87}Rb, and a mass bias estimated by the {sup 88}Sr/{sup 86}Sr ratio. The method was applied to an otolith (ear-stone) from ayu (Plecoglossus altivelis altivelis) collected from the Yodo river, Japan. Although experimental errors are relatively large, up to 3 per mille at 2{sigma}, the ratios of the core region are higher than the seawater signature while more distal values agree well with seawater. The very outermost part again shows the relatively higher {sup 87}Sr/{sup 86}Sr ratios. The spatial variation of {sup 87}Sr/{sup 86}Sr ratios was consistent with amphidromous migration of the fish, namely, born in the lake and grown in the coastal sea and finally collected in a river.

  11. Ion microprobe Sr isotope analysis of carbonates with about 5 μm spatial resolution: An example from an ayu otolith

    International Nuclear Information System (INIS)

    Sano, Yuji; Shirai, Kotaro; Takahata, Naoto; Amakawa, Hiroshi; Otake, Tsuguo

    2008-01-01

    A high lateral resolution secondary ion mass spectrometer (NanoSIMS NS50 ion microprobe) has been used to measure 87 Sr/ 86 Sr ratios in natural CaCO 3 samples. A ∼2 nA O - primary beam was used to sputter a 5-7-μm diameter crater on the sample surface and secondary positive ions were extracted for mass analysis using an accelerating voltage of 8 kV and a Mattauch-Herzog geometry. The multi-collector system was adjusted to detect 43 Ca + (by a detector EM2), 80 Ca 2 + (EM3), 86 Sr + (EM4), and 87 Sr + (EM4b) ions at the same time. Then the magnetic field was scanned for the EM4 to detect 85 Rb + , 86 Sr + and 87 Sr + , while the EM4b can measure 86 Sr + , 87 Sr + and 88 Sr + , respectively. A mass resolution of 3600 at 10% peak height was attained with a flat peak top, while the sensitivity of Sr was about 10 cps/nA/ppm. An aragonite sample (coral skeleton standard; JCp-1) was used as a reference for Sr isotope ratio calibration. Repeated analyses of the JCp-1 show that the 87 Sr/ 86 Sr ratio agrees well with the seawater signature within a precision of 0.3 per mille at 2σ, after the series of corrections such as the Ca dimer, 87 Rb, and a mass bias estimated by the 88 Sr/ 86 Sr ratio. The method was applied to an otolith (ear-stone) from ayu (Plecoglossus altivelis altivelis) collected from the Yodo river, Japan. Although experimental errors are relatively large, up to 3 per mille at 2σ, the ratios of the core region are higher than the seawater signature while more distal values agree well with seawater. The very outermost part again shows the relatively higher 87 Sr/ 86 Sr ratios. The spatial variation of 87 Sr/ 86 Sr ratios was consistent with amphidromous migration of the fish, namely, born in the lake and grown in the coastal sea and finally collected in a river

  12. 89Sr and 90Sr in atmospheric precipitations in May 1986 in Bucharest-Magurele area

    International Nuclear Information System (INIS)

    Paunescu, N.; Vata, I.

    1987-08-01

    Sr-89 and Sr-90 were determined in the fallout of May 1986. The maximum values of 335 Bq/(m 2 * 6 hours) and 110 Bq/(m 2 * 6 hours) were observed at May 2 and 5. Throughout May 1986 a quantity of 860 Bq/m 2 of Sr-90 deposited from the fallout in the Bucharest -Magurele area was determined. (authors)

  13. Results of field studies on 90SR and stable SR soil-to-plant transfer

    International Nuclear Information System (INIS)

    Gerzabek, M.H.; Artner, C.; Horak, O.; Mueck, K.

    1992-01-01

    In 1987 and 1988 at 35 sites plants ready to harvest and the corresponding soils (0 - 20 cm) were collected for 90 Sr and stable strontium analyses. Sample preparation and measurement led to a detection limit of 0.008 Bq 90 Sr kg -1 . The 90 Sr-contamination of Austrian soils ranged from 396 to 1998 Bq m -2 . Known from literature the contribution of the Chernobyl fallout amounted to app. 25 % of the total contamination. Stable strontium contents of the soils were between 6 and 62.5 mg kg -1 . Bariumtriethanolamine extracted 17.7 to 62.3 % of the total stable Sr in soil. 90 Sr-concentrations in cereal grains ranged from 0.03 to 0.67 Bq kg -1 (fresh wight) for maize and barley, respectively. The values for other foodstuff were between 0.15 (white cabbage) and 0.91 Bq kg -1 (spinach). Stable strontium contents were between 0.079 mg kg -1 (maize) and 72.5 mg kg -1 (celery shoot). The following mean 90 Sr soil-to-plant transfer factors for cereal grains were obtained: 0.010 (maize), 0.097 (rye), 0.049 (wheat), 0.095 (barley). Transfer factors for straw were up to 50 times higher (maize). The transfer of 90 Sr into vegetables and potatoes reached the same order of magnitude compared to the cereals. In all cases soil-to-plant transfer of stable Sr was clearly lower up to 60 % of the respective values for 90 Sr. Thus natural stable strontium is less plant available than 90 Sr. The influence of soil parameters on the 90 Sr transfer into plants was examinated by correlation analyses. Increasing exchangeable calcium contents of the soils resulted in a significant reduction of Sr soil-to-barley straw transfer. (authors)

  14. Addition to the analysis of the Sr VI and Sr VII spectra

    International Nuclear Information System (INIS)

    Wyart, J.F.

    1989-01-01

    Fifty-six lines of multicharged strontium are measured with an improved wavelength accuracy, or interpreted for the first time. They are 4p-4s, 4p-5s and 4p-4d transitions in Sr VII and 4p-5s transitions in Sr VI. The revision of the singlet-triplet connection in Sr VII is supported by theoretical survey of the ground configuration in Ge-like ions. (orig.)

  15. Catalytic surface promotion of highly active La0.85Sr0.15Cr0.8Ni0.2O3-δ anodes for La5.6WO11.4-δ based proton conducting fuel cells

    DEFF Research Database (Denmark)

    Solis, C.; Balaguer, M.; Bozza, Francesco

    2014-01-01

    La0.85Sr0.15CrO3-delta (LSC), La0.85Sr0.15Cr0.8Ni0.2O3-delta (LSCN) and LSCN infiltrated with Ni nanoparticles were tested as anodes for symmetrical cells based on La5.6WO11.4-delta (LWO) protonic electrolyte. These chromite-based electrode materials are compatible with LWO material, in contrast ...

  16. 82Sr--82Rb radioisotope generator

    International Nuclear Information System (INIS)

    Grant, P.M.; Erdal, B.R.; O'Brien, H.A.

    1976-01-01

    An improved 82 Sr- 82 Rb radioisotope generator system, based upon the complexing ion exchange resin Chelex-100, has been developed. Columns of this material can be easily and rapidly milked, and the Rb-Sr separation factor for a fresh generator was found to be greater than 10 7 . Approximately 80 percent of the 82 Rb present was delivered in a 15-ml volume of aqueous 0.2 M NH 4 Cl solution. After more than 6 liters of eluant had been put through the generator, the Rb-Sr separation factor was still observed to be greater than 10 5 , and no unusual strontium breakthrough behavior was seen in the system over nearly three 82 Sr half lives. 2 claims, no drawings

  17. CHARACTERIZATION OF THE PARTIALLY PURIFIED PLANTARCIN SR18 PRODUCED BY LACTOBACILLUS PLANTARUM SR18

    Directory of Open Access Journals (Sweden)

    Wagih El-Shouny

    2013-04-01

    Full Text Available The bacteriocin bound to the cells and that secreted into the culture filtrate of Lactobacillus plantarum SR18 were precipitated by 75% ammomium sulphate, dialysed and further purified by Gel filtration on Sephadex G-100. Bacteriocins were purified from proteins bound to the cell of L. plantarum SR18 (plantarcin SR18 a and culture filtrate proteins (plantarcin SR18 b, respectively. The SDS-PAGE of partially purified Plantarcin SR18a showed a molecular weight of 3.5 KDa. While, plantarcin SR18 b had a molecular weight of 10.3 KDa. The antibacterial activity of the tested plantarcin SR18 preparations suffered no measurable loss after 45 min at 80ºC. Whereas, At 100ºC, significant decrease in the activity of bacteriocin preparations (60- 80 % took place by the end of 45 min. At pH ranged from 5-8, the activity of the plantarcin SR18 preparations suffered no measurable loss. Dissociating agents significantly affected the bacteriocin activity. Thus, tween 80 and mercaptoethanol increased the activity of bacteriocin preparations to 1.2-1.4 fold. Sodium dodecyl sulphate (SDS increased the activity of the tested bacteriocin preparations by about 20%.The lowest residual activity (60% was recorded after treatment with Triton X100 for 45 min. Protease completely inhibited the activities of all forms of plantarcin SR18 after 45 min at 37ºC.

  18. Characterization of Sr2+ uptake on natural minerals of kaolinite and magnesite using XRPD, SEM/EDS, XPS, and DRIFT

    International Nuclear Information System (INIS)

    Shahwan, T.; Erten, H.N.

    2005-01-01

    The sorption behavior of Sr 2+ ions on natural minerals rich in kaolinite and magnesite was studied using SEM/EDS, XPS, XRPD, AAS/AES and DRIFT techniques. Quantitative analysis of the XPS data shows that magnesite is more effective in Sr 2+ uptake than kaolinite. DRIFT spectra and XRPD patterns indicate that the structures of both minerals were not affected upon Sr 2+ sorption. Intercalation of DMSO in kaolinite lamellae aiming at increasing the interlayer space did not significantly enhance the sorption capacity of the clay towards Sr 2+ probably due to the lack of a negative charge on the accessible sites. EDS mapping indicated that while the sorbed Sr is equally distributed on surface of natural kaolinite, it was associated - to a larger extent - with the regions richer in Mg in the case of natural magnesite. Comparing the uptake mechanisms of natural magnesite with that of pure MgCO 3 , it was seen that while natural magnesite sorbed Sr 2+ mainly through an ion exchange type mechanism, the formation of SrCO 3 coprecipitate was detected on the surface of the MgCO 3 at higher loadings. (orig.)

  19. BiCaSrCuO superconductors

    International Nuclear Information System (INIS)

    Polvi, V.M.; Niemi, K.J.

    1989-01-01

    BiCaSrCuO and BiPbCaSrCuO powders have been synthesized. Different research methods (SEM,EDS,XRF,SRD,DTA) have been used to characterize the bulk specimen and wires. Resistance and current density measured as a function of temperature are reported. The ceramic products contained several phases. Lead containing specimen gave the best results and the synthesis was easily reproducible

  20. Renewable Energy Country Profiles. Caribbean

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-09-15

    IRENA Renewable Energy Country Profiles take stock of the latest developments in the field of renewables at country level around the world. Each profile combines analysis by IRENA's specialists with the latest available country data and additional information from a wide array of sources. The resulting reports provide a brief yet comprehensive picture of the situation with regard to renewable energy, including energy supply, electrical generation and grid capacity, and access. Energy policies, targets and projects are also considered, along with each country's investment climate and endowment with renewable energy resources. The energy statistics presented here span the period from 2009 until 2012, reflecting varying timelines in the source material. Since data availability differs from country to country, wider regional comparisons are possible only for the latest year with figures available for every country included. Despite the time lag in some cases, the evident differences and disparities between countries and regions around the world remain striking. The current package of country profiles is just a starting point. The geographic scope will continue to expand, and existing profiles will be enhanced with new indicators, with the whole series maintained as a live product on the IRENA website (www.irena.org)

  1. The USNCR license renewal process

    International Nuclear Information System (INIS)

    Kuo, Pao-Tsin

    2002-01-01

    The US Congress promulgated a law in 1954, entitled 'Atomic Energy Act'. This Act states that operating licenses for commercial nuclear power plants are limited to a fixed term of 40 years, but they may be renewed for a period not to exceed 20 years. The terms were established mainly for economic considerations, not based on technical limitations. The U.S. Nuclear Regulatory Commission (USNRC) published the license renewal rule, Title 10 of the Code of Federal Regulations, Part 54 (10 CFR Part 54), in December, 1991. The rule has since been amended in May, 1995. The underlying principle of the rule is that the regulatory process is adequate for ensuring safety of operating plants. The regulatory process includes NRC's issuance of Orders, Bulletins, Generic Letters, and Information Notices, as well as a number of special inspections in addition to the continuous oversight and routine inspection activities performed by on-site inspectors. Because of this comprehensive regulatory process, compilation of the current license basis or re-verification of the current licensing basis is not considered necessary for a license renewal review. The USNRC also determined on the basis of the findings of its research programs that active structures and components are well maintained by the existing programs. Therefore, the focus of the license renewal review is on passive, long-lived structures and components and on time-limited ageing analyses. The time-limited ageing analyses are for those structures and components which were originally designed to a 40 year service life

  2. The potential of renewable energy

    Energy Technology Data Exchange (ETDEWEB)

    1990-03-01

    On June 27 and 28, 1989, the US Department of Energy (DOE) national laboratories were convened to discuss plans for the development of a National Energy Strategy (NES) and, in particular, the analytic needs in support of NES that could be addressed by the laboratories. As a result of that meeting, interlaboratory teams were formed to produce analytic white papers on key topics, and a lead laboratory was designated for each core laboratory team. The broad-ranging renewables assignment is summarized by the following issue statement from the Office of Policy, Planning and Analysis: to what extent can renewable energy technologies contribute to diversifying sources of energy supply What are the major barriers to greater renewable energy use and what is the potential timing of widespread commercialization for various categories of applications This report presents the results of the intensive activity initiated by the June 1989 meeting to produce a white paper on renewable energy. Scores of scientists, analysts, and engineers in the five core laboratories gave generously of their time over the past eight months to produce this document. Their generous, constructive efforts are hereby gratefully acknowledged. 126 refs., 44 figs., 32 tabs.

  3. Shapes of a Renewable Society.

    Science.gov (United States)

    Deudney, Daniel; Flavin, Christopher

    1983-01-01

    To rely on coal and nuclear power as sources of energy is to narrow society's future options and to present numerous problems. Renewable solar energy, on the other hand, can preserve rather than reduce options. More jobs, rising self-reliance, and new equalities between nations will be the result. (RM)

  4. Innovative biofibers from renewable resources

    CERN Document Server

    Reddy, Narendra

    2015-01-01

    This book will be a one-stop-shop for readers seeking information on biofibers that are sustainable and environmentally friendly and those that can replace the non-renewable synthetic polymer based fibers. Emphasis will be on fibers that are derived from agricultural byproducts and coproducts without the need for additional natural resources.

  5. Solar Renewable Energy. Teaching Unit.

    Science.gov (United States)

    Buchanan, Marion; And Others

    This unit develops the concept of solar energy as a renewable resource. It includes: (1) an introductory section (developing understandings of photosynthesis and impact of solar energy); (2) information on solar energy use (including applications and geographic limitations of solar energy use); and (3) future considerations of solar energy…

  6. Analysis of renewable portfolio standards

    Energy Technology Data Exchange (ETDEWEB)

    Bernow, S.; Dougherty, W.; Duckworth, M.

    1997-12-31

    A national RPS would increase the fraction of U.S. electricity generation from renewable technologies at least cost. It would help ensure that the cost and performance of these technologies would improve with manufacturing experience, scale economies, and learning-by-doing from their integration into electric systems. Thus, their economic, environmental, energy security, and sustainability benefits would be realized.

  7. Legal framework: Renewables in Honduras

    International Nuclear Information System (INIS)

    Matute, Leonardo

    2000-01-01

    The paper describes the framework (organic structure and legislation) in promotion of renewables in Honduras, the policies for promotion of the free market of energy, laws on environmental protection and law of electricity. Also describes treties and agreements suscribed by Honduras in these matters

  8. Renewables 2012 - Global status report

    International Nuclear Information System (INIS)

    Sawin, Janet L.; Bhattacharya, Sribas Chandra; Galan, Ernesto Macias; McCrone, Angus; Moomaw, William R.; Sims, Ralph; Sonntag-O'Brien, Virginia; Sverrisson, Freyr; Chawla, Kanika; Adib, Rana; Musolino, Evan; Mastny, Lisa; Skeen, Jonathan; Martinot, Eric; Hinrichs-Rahlwes, Rainer

    2012-01-01

    Renewable energy markets and policy frameworks have evolved rapidly in recent years. This report provides a comprehensive and timely overview of renewable energy market, industry, investment, and policy developments worldwide. It relies on the most recent data available, provided by a network of more than 400 contributors and researchers from around the world, all of which is brought together by a multi-disciplinary authoring team. The report covers recent developments, current status, and key trends; by design, it does not provide analysis or forecast the future. As such, this report and subsequent editions will serve as a benchmark for measuring global progress in the deployment of renewable energy, which is of particular interest in this International Year of Sustainable Energy for All. UN Secretary-General Ban Ki-moon has marked the occasion with a new global initiative, Sustainable Energy for All, which seeks to mobilise global action on three inter-linked objectives to be achieved by 2030: universal access to modern energy services, improved rates of energy efficiency, and expanded use of renewable energy sources

  9. Power marketing and renewable energy

    International Nuclear Information System (INIS)

    Fang, J.M.

    1997-01-01

    Power marketing refers to wholesale and retail transactions of electric power made by companies other than public power entities and the regulated utilities that own the generation and distribution lines. The growth in power marketing has been a major development in the electric power industry during the last few years, and power marketers are expected to realize even more market opportunities as electric industry deregulation proceeds from wholesale competition to retail competition. This Topical Issues Brief examines the nature of the power marketing business and its relationship with renewable power. The information presented is based on interviews conducted with nine power marketing companies, which accounted for almost 54% of total power sales by power marketers in 1995. These interviews provided information on various viewpoints of power marketers, their experience with renewables, and their respective outlooks for including renewables in their resource portfolios. Some basic differences exist between wholesale and retail competition that should be recognized when discussing power marketing and renewable power. At the wholesale level, the majority of power marketers stress the commodity nature of electricity. The primary criteria for developing resource portfolios are the same as those of their wholesale customers: the cost and reliability of power supplies. At the retail level, electricity may be viewed as a product that includes value-added characteristics or services determined by customer preferences

  10. Renewable energies and public policies

    International Nuclear Information System (INIS)

    Cochet, Y.; Pierret, Ch.; Lienemann, M.N.

    2002-04-01

    This document presents the interventions of political personalities on the topic of the renewable energies development policies and the necessity of financial incentives which have been discussed during the colloquium of thursday 4 april 2002 at Paris. (A.L.B.)

  11. The renewable energies in Uruguay

    International Nuclear Information System (INIS)

    2011-01-01

    This report is about the energetic politc and its strong commitment with the incorporation of autochthonous sources and renewable energy. The objective and the main lines of action in Uruguay are: provide electric power, wind, biomass, bioethanol, biodiesel, solar and hydroelectric power

  12. Conservation and Renewable Energy Program

    Energy Technology Data Exchange (ETDEWEB)

    Vaughan, K.H.

    1991-05-01

    This bibliography lists reports and selected papers published under the Oak Ridge National Laboratory Conservation and Renewable Energy Program from 1986 through February 1991. Information on documents published prior to 1986 can be obtained from ORNL. Most of the documents in the bibliography are available from Oak Ridge National Laboratory.

  13. Heliodromus : Renewable energy from space

    NARCIS (Netherlands)

    Kuiper, J.M.

    2010-01-01

    Climate change and the related running out of fossil fuel reserves drive the development of renewable energy sources. To contribute to a solution of these problems, we present the results of a BSc student design synthesis exercise project on Space Based Solar Power (SBSP). A SBSP system generates

  14. New Quebec renewable energy organization

    Energy Technology Data Exchange (ETDEWEB)

    McArthur, D.; Salaff, S.

    1998-04-01

    The recent formation of the Quebec Association for the Production of Renewable Energy (l`Association quebecoise de la production d`energie renouvelable - AQPER) was announced. The Association is becoming the centre of the Quebec private electricity generation industry. By communicating the industry`s message to the public the organization gives much needed visibility to renewable resources, new forms of energy and sustainable development. The new group is an outgrowth of the former Quebec Association of Private Hydroelectricity Producers. In its new reincarnation, the organization represents all forms of renewables, small and medium hydro, wind, solar, forest and agricultural biomass and urban waste. With deregulation of the electricity market, specifically the creation of the Regie de l`energie` in Quebec, the wider role is a welcome boost for renewable energy development in the province. In one of its first actions the AQPER recommended that all hydroelectric sites up to 50 MW be reserved for development exclusively by the private sector, in conformity with the Quebec energy policy announced in 1996.

  15. Renewable electricity in the Netherlands

    International Nuclear Information System (INIS)

    Junginger, M.; Agterbosch, S.; Faaij, A.; Turkenburg, W.

    2004-01-01

    The Dutch policy goal is to achieve a share of 17% renewable electricity in the domestic demand in 2020, corresponding to 18-24 TWh. It is uncertain whether and under which conditions this aim can be achieved. This paper aims to explore the feasible deployment of renewable electricity production in the Netherlands until 2020 by evaluating different images representing policies and societal preferences. Simultaneously, the most promising technologies for different settings are investigated and identified. First Dutch policy goals, governmental policy measures and definitions of renewable electricity are discussed. Second, a comparison is made of four existing studies that analyze the possible developments of renewable electricity production in the coming decades. Finally, three images are set up with emphasis on the different key factors that influence the maximum realizable potential. Results indicate onshore wind, offshore wind and large-scale biomass plants as most promising, robust options in terms of economical performance, ecological sustainability and high technical implementation rate. In the image with high implementation rates, an annual production of 42 TWh may be achieved in 2020, while under stringent economical or ecological criteria, about 25 TWh may be reached. When only the robust options are considered, 9-22 TWh can be realized. The analysis illustrates the importance of taking the different key factors mentioned influencing implementation into account. Doing so allows for identification of robust and less robust technological options under different conditions

  16. Modification of Sr on 4004 Aluminum Alloy

    Science.gov (United States)

    Guo, Erjun; Cao, Guojian; Feng, Yicheng; Wang, Liping; Wang, Guojun; Lv, Xinyu

    2013-05-01

    As a brazing foil, 4004 Al alloy has good welding performance. However, the high Si content decreases the plasticity of the alloy. To improve the plasticity of 4004 Al alloy and subsequently improve the productivity of 4004 Al foil or 434 composite foil, 4004 Al alloy was modified by Al-10%Sr master alloy. Modification effects of an additional amount of Sr, modification temperature, and holding time on 4004 aluminum alloy were studied by orthogonal design. The results showed that the greatest impact parameter of 4004 aluminum alloy modification was the additional amount of Sr, followed by holding time and modification temperature. The optimum modification parameters obtained by orthogonal design were as follows: Sr addition of 0.04%, holding time of 60 min, and modification temperature of 760°C. The effect of Sr addition on modification was analyzed in detail based on orthogonal results. With increasing of Sr addition, elongation of 4004 alloy increased at first, and decreased after reaching the maximum value.

  17. A multi-scaled hybrid orthopedic implant: bone ECM-shaped Sr-HA nanofibers on the microporous walls of a macroporous titanium scaffold

    Energy Technology Data Exchange (ETDEWEB)

    Han Yong; Zhou Jianhong; Zhang Lan; Xu Kewei, E-mail: yonghan@mail.xjtu.edu.cn [State Key Laboratory for Mechanical Behavior of Materials, Xi' an Jiaotong University, Xi' an 710049 (China)

    2011-07-08

    We report here, for the first time, a novel multi-scaled hybrid orthopedic implant material consisting of a macroporous Ti scaffold, whose macropores' walls have a microporous titania layer which is fully covered with nanofibers of Sr-doped hydroxyapatite (Sr-HA). The microporous titania layer is formed on and within the Ti scaffold by micro-arc oxidation, which firmly binds to the Ti substrate and contains Ca{sup 2+}, Sr{sup 2+} and PO{sub 4}{sup 3-} ions. It is then hydrothermally treated to form Sr-HA nanofibers. During the hydrothermal treatment, Sr-HA nanoprisms nucleate from Ca{sub 0.5}Sr{sub 0.5}TiO{sub 3} pre-formed on the TiO{sub 2} and grow in length to nanofibers at the expense of Ca{sup 2+}, Sr{sup 2+} and PO{sub 4}{sup 3-} ions that migrate from the TiO{sub 2}. These Sr-HA nanofibers construct a network structure similar to the hierarchical organization of bone extracellular matrix (ECM), and the resulting nanofibrous surface displays a firm adhesion to substrate, superhydrophilicity and apatite-inducing ability. The induced apatite prefers to nucleate on the basal-faceted surfaces of Sr-HA nanofibers. The nanofiber-walled scaffold has a great potential for load-bearing orthotopic use.

  18. A multi-scaled hybrid orthopedic implant: bone ECM-shaped Sr-HA nanofibers on the microporous walls of a macroporous titanium scaffold.

    Science.gov (United States)

    Han, Yong; Zhou, Jianhong; Zhang, Lan; Xu, Kewei

    2011-07-08

    We report here, for the first time, a novel multi-scaled hybrid orthopedic implant material consisting of a macroporous Ti scaffold, whose macropores' walls have a microporous titania layer which is fully covered with nanofibers of Sr-doped hydroxyapatite (Sr-HA). The microporous titania layer is formed on and within the Ti scaffold by micro-arc oxidation, which firmly binds to the Ti substrate and contains Ca2+, Sr2+ and PO4(3-) ions. It is then hydrothermally treated to form Sr-HA nanofibers. During the hydrothermal treatment, Sr-HA nanoprisms nucleate from Ca0.5Sr0.5TiO3 pre-formed on the TiO2 and grow in length to nanofibers at the expense of Ca2+, Sr2+ and PO4(3-) ions that migrate from the TiO2. These Sr-HA nanofibers construct a network structure similar to the hierarchical organization of bone extracellular matrix (ECM), and the resulting nanofibrous surface displays a firm adhesion to substrate, superhydrophilicity and apatite-inducing ability. The induced apatite prefers to nucleate on the basal-faceted surfaces of Sr-HA nanofibers. The nanofiber-walled scaffold has a great potential for load-bearing orthotopic use.

  19. Christmas Valley Renewable Energy Assessment

    Energy Technology Data Exchange (ETDEWEB)

    Del Mar, Robert [Oregon Department of Energy, Salem, OR (United States)

    2017-05-22

    In partnership with the Oregon Military Department, the Department of Energy used the award to assess and evaluate renewable resources in a 2,622-acre location in Lake County, central Oregon, leading to future development of up to 200 MW of solar electricity. In partnership with the Oregon Military Department, the Department of Energy used the award to assess and evaluate renewable resources in a 2,622-acre location in Lake County, central Oregon, leading to future development of up to 200 MW of solar electricity. The Oregon Military Department (Military) acquired a large parcel of land located in south central Oregon. The land was previously owned by the US Air Force and developed for an Over-the-Horizon Backscatter Radar Transmitter Facility, located about 10 miles east of the town of Christmas Valley. The Military is investigating a number of uses for the site, including Research and Development (R&D) laboratory, emergency response, military operations, developing renewable energy and related educational programs. One of the key potential uses would be for a large scale solar photovoltaic power plant. This is an attractive use because the site has excellent solar exposure; an existing strong electrical interconnection to the power grid; and a secure location at a moderate cost per acre. The project objectives include: 1. Site evaluation 2. Research and Development (R&D) facility analysis 3. Utility interconnection studies and agreements 4. Additional on-site renewable energy resources analysis 5. Community education, outreach and mitigation 6. Renewable energy and emergency readiness training program for veterans

  20. Renewable energy resources; Erneuerbare Energien

    Energy Technology Data Exchange (ETDEWEB)

    Lenz, Volker; Naumann, Karin [DBFZ Deutsches Biomasseforschungszentrum gemeinnuetzige GmbH, Leipzig (Germany); Kaltschmitt, Martin; Janczik, Sebastian [Technische Univ. Hamburg-Harburg (Germany). Inst. fuer Umwelttechnik und Energiewirtschaft

    2015-07-01

    Although the need to decarbonise our global economy and thus in particular the supply of energy to limit the global temperature increase is internationally undisputed the German politics in 2014 has significantly contributed less compared to previous years in order to attain this objective. The expansion of renewable energies in the electricity sector has decelerated significantly; and in the heating and mobility area no new impulses were set in relation to renewable energies. In addition, a dramatic fallen oil price makes it difficult to increase the use of renewable energy supply. Based on these deteriorated framework conditions compared to conditions of the previous years, the developments in Germany of 2014 are shown in the electricity, heat and transport sector in the field of renewable energy. For this purpose - in addition to a discussion of the current energy economic framework - for each option to use renewable energies the state and looming trends are analyzed. [German] Obwohl die Notwendigkeit zur Dekarbonisierung unserer globalen Wirtschaft und damit insbesondere der Energiebereitstellung zur Begrenzung des globalen Temperaturanstiegs international unstrittig ist, hat die deutsche Politik im Jahr 2014 im Vergleich zu den Vorjahren deutlich weniger zur Erreichung dieses Zieles beigetragen. Der Ausbau der Stromerzeugung aus erneuerbaren Energien im Stromsektor wurde deutlich verlangsamt; und im Waerme- und Mobilitaetsbereich wurden keine neuen Impulse in Bezug auf regenerative Energien gesetzt. Zusaetzlich erschwert ein drastisch gefallener Rohoelpreis die verstaerkte Nutzung des erneuerbaren Energieangebots. Ausgehend von diesen im Vergleich zu den Vorjahren verschlechterten Rahmenbedingungen werden nachfolgend die Entwicklungen in Deutschland des Jahres 2014 im Strom-, Waerme- und Transportsektor fuer den Bereich der erneuerbaren Energien aufgezeigt. Dazu werden - neben einer Diskussion des derzeitigen energiewirtschaftlichen Rahmens - fuer die