WorldWideScience

Sample records for surface morphology depends

  1. Magnetic-field-dependent morphology of self-organized Fe on stepped Si(111) surfaces

    International Nuclear Information System (INIS)

    Cougo dos Santos, M.; Geshev, J.; Pereira, L. G.; Schmidt, J. E.

    2009-01-01

    The present work reports on Fe thin films grown on vicinal Si(111) substrates via rf magnetron sputtering. The dependencies of the growth mode and magnetic properties of the obtained iron nanostructures on both crystallographic surface orientation and on the direction of the very weak stray magnetic field from the magnetron gun were studied. Scanning tunneling microscopy images showed strong dependence of the Fe grains' orientation on the stray field direction in relation to the substrate's steps demonstrating that, under appropriately directed magnetic field, Si surfaces can be used as templates for well-defined self-assembled iron nanostructures. Magneto-optical Kerr effect hysteresis loops showed an easy-axis coercivity almost one order of magnitude smaller for the film deposited with stray field applied along the steps, accompanied with a change in the magnetization reversal mode. Phenomenological models involving coherent rotation and/or domain-wall unpinning were used for the interpretation of these results.

  2. Surface morphology of polyethylene glycol films produced by matrix-assisted pulsed laser evaporation (MAPLE): Dependence on substrate temperature

    DEFF Research Database (Denmark)

    Rodrigo, K.; Czuba, P.; Toftmann, B.

    2006-01-01

    The dependence of the surface morphology on the substrate temperature during film deposition was investigated for polyethylene glycol (PEG) films by matrix-assisted pulsed laser evaporation (MAPLE). The surface structure was studied with a combined technique of optical imaging and AFM measurements....... There was a clear difference between the films produced below and above the melting point of PEG. For temperatures above the melting point, the polymer material was distributed non-uniformly over the substrate with growths areas, where cluster-like structures merge into large islands of micrometer size....... At these temperatures, the islands in the investigated growth areas cover most of the bottom layer which has a typical height of 50-150 nm. (c) 2005 Elsevier B.V. All rights reserved....

  3. From nanodroplets to continuous films: how the morphology of polyelectrolyte multilayers depends on the dielectric permittivity and the surface charge of the supporting substrate

    NARCIS (Netherlands)

    Guillaume-Gentil, Orane; Zahn, Raphael; Lindhoud, Saskia; Graf, Norma; Voros, Janos; Zambelli, Tomaso

    2011-01-01

    Using atomic force microscopy, we investigated how the morphology of layer-by-layer deposited polyelectrolyte multilayers is influenced by the physical properties of the supporting substrate. The surface coverage of the assembly and its topography were found to be dependent on the dielectric

  4. Observations of orientation dependence of surface morphology in tungsten implanted by low energy and high flux D plasma

    DEFF Research Database (Denmark)

    Xu, H.Y.; Zhang, Yubin; Yuan, Y.

    2013-01-01

    Surface modification by formation of blistering and nanostructures with pronounced orientation dependence has been observed on surfaces of rolled tungsten and recrystallized tungsten after exposure to a low energy (38 eV) deuterium (D) plasma with a high flux of 1024 m-2 s -1. The correlation bet...

  5. Growth morphologies of crystal surfaces

    Science.gov (United States)

    Xiao, Rong-Fu; Alexander, J. Iwan D.; Rosenberger, Franz

    1991-03-01

    We have expanded our earlier Monte Carlo model [Phys. Rev. A 38, 2447 (1988); J. Crystal Growth 100, 313 (1990)] to three dimensions and included reevaporation after accommodation and growth on dislocation-induced steps. We found again that, for a given set of growth parameters, the critical size, beyond which a crystal cannot retain its macroscopically faceted shape, scales linearly with the mean free path in the vapor. However, the three-dimensional (3D) the systems show increased shape stability compared to corresponding 2D cases. Extrapolation of the model results to mean-free-path conditions used in morphological stability experiments leads to order-of-magnitude agreement of the predicted critical size with experimental findings. The stability region for macroscopically smooth (faceted) surfaces in the parameter space of temperature and supersaturation depends on both the surface and bulk diffusion. While surface diffusion is seen to smooth the growth morphology on the scale of the surface diffusion length, bulk diffusion is always destabilizing. The atomic surface roughness increases with increase in growth temperature and supersaturation. That is, the tendency of surface kinetics anisotropies to stabilize the growth shape is reduced through thermal and kinetic roughening. It is also found that the solid-on-solid assumption, which can be advantageously used at low temperatures and supersaturations, is insufficient to describe the growth dynamics of atomically rough interfaces where bulk diffusion governs the process. For surfaces with an emerging screw dislocation, we find that the spiral growth mechanism dominates at low temperatures and supersaturations. The polygonization of a growth spiral decreases with increasing temperature or supersaturation. When the mean free path in the nutrient is comparable to the lattice constant, the combined effect of bulk and surface diffusion reduces the terrace width of a growth spiral in its center region. At elevated

  6. Morphology dependent catalysis and surface enhanced Raman scattering (SERS) studies using Pd nanostructures in DNA, CTAB and PVA scaffolds.

    Science.gov (United States)

    Kundu, Subrata; Yi, Su-In; Ma, Lian; Chen, Yunyun; Dai, Wei; Sinyukov, Alexander M; Liang, Hong

    2017-07-25

    Palladium nanoparticles (Pd NPs) of three different morphologies viz., nanocubes with cetyltrimethylammonium bromide (CTAB), nanowires with polyvinyl alcohol (PVA) and Pd NPs with deoxyribonucleic acid (DNA) scaffolds were synthesized by UV-irradiation. Catalysis and surface enhanced Raman scattering (SERS) studies were done with the synthesized morphologically distinct Pd nanostructures for the very first time. The catalytic rate was extremely high with Pd nanowires templated with PVA and the order of the catalytic rate was Pd nanowires in PVA > Pd nanocubes in CTAB > DNA-Pd wire-like assemblies. The highest catalytic rate was observed for PVA capped Pd nanowires which is a few hundred fold higher than other metal NP catalysts. Methylene blue (MB) was used as a Raman analyte for the SERS study and the largest EF of 1.9 × 10 5 at a peak position of 1391 cm -1 was observed with Pd nanowires in the DNA scaffold as a SERS substrate. The order of the SERS EF values was DNA-Pd wire-like assemblies > Pd nanocubes in CTAB > Pd nanowires in PVA. Beyond everything, the present synthesis route is easy, faster, candid, highly reproducible and cost-effective. In the near future, the same protocol could be applied to synthesize other materials for various applications.

  7. Dependence of Plant Uptake and Diffusion of Polycyclic Aromatic Hydrocarbons on the Leaf Surface Morphology and Micro-structures of Cuticular Waxes

    Science.gov (United States)

    Li, Qingqing; Li, Yungui; Zhu, Lizhong; Xing, Baoshan; Chen, Baoliang

    2017-04-01

    The uptake of organic chemicals by plants is considered of great significance as it impacts their environmental transport and fate and threatens crop growth and food safety. Herein, the dependence of the uptake, penetration, and distribution of sixteen polycyclic aromatic hydrocarbons (PAHs) on the morphology and micro-structures of cuticular waxes on leaf surfaces was investigated. Plant surface morphologies and wax micro-structures were examined by scanning emission microscopy, and hydrophobicities of plant surfaces were monitored through contact angle measurements. PAHs in the cuticles and inner tissues were distinguished by sequential extraction, and the cuticle was verified to be the dominant reservoir for the accumulation of lipophilic pollutants. The interspecies differences in PAH concentrations cannot be explained by normalizing them to the plant lipid content. PAHs in the inner tissues became concentrated with the increase of tissue lipid content, while a generally negative correlation between the PAH concentration in cuticles and the epicuticular wax content was found. PAHs on the adaxial and abaxial sides of a leaf were differentiated for the first time, and the divergence between these two sides can be ascribed to the variations in surface morphologies. The role of leaf lipids was redefined and differentiated.

  8. Morphology of ion-sputtered surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Makeev, Maxim A. E-mail: makeev@baton.phys.lsu.edu; Cuerno, Rodolfo; Barabasi, Albert-Laszlo

    2002-12-01

    We derive a stochastic nonlinear continuum equation to describe the morphological evolution of amorphous surfaces eroded by ion bombardment. Starting from Sigmund's theory of sputter erosion, we calculate the coefficients appearing in the continuum equation in terms of the physical parameters characterizing the sputtering process. We analyze the morphological features predicted by the continuum theory, comparing them with the experimentally reported morphologies. We show that for short time scales, where the effect of nonlinear terms is negligible, the continuum theory predicts ripple formation. We demonstrate that in addition to relaxation by thermal surface diffusion, the sputtering process can also contribute to the smoothing mechanisms shaping the surface morphology. We explicitly calculate an effective surface diffusion constant characterizing this smoothing effect and show that it is responsible for the low temperature ripple formation observed in various experiments. At long time scales the nonlinear terms dominate the evolution of the surface morphology. The nonlinear terms lead to the stabilization of the ripple wavelength and we show that, depending on the experimental parameters, such as angle of incidence and ion energy, different morphologies can be observed: asymptotically, sputter eroded surfaces could undergo kinetic roughening, or can display novel ordered structures with rotated ripples. Finally, we discuss in detail the existing experimental support for the proposed theory and uncover novel features of the surface morphology and evolution, that could be directly tested experimentally.

  9. Spectrophotometric evaluation of surface morphology dependent catalytic activity of biosynthesized silver and gold nanoparticles using UV–vis spectra: A comparative kinetic study

    International Nuclear Information System (INIS)

    Ankamwar, Balaprasad; Kamble, Vaishali; Sur, Ujjal Kumar; Santra, Chittaranjan

    2016-01-01

    Graphical abstract: - Highlights: • The biosynthesized silver nanoparticles were stable for 6 months and used as effective SERS active substrate. • They are effective catalyst in the chemical reduction of 4-nitrophenol to 4-aminophenol. • Comparative catalytic efficiency of both silver and gold nanoparticles was studied spectrophotometrically. • Our results demonstrate surface morphology dependent catalytic activity of both nanoparticles. - Abstract: The development of eco-friendly and cost-effective synthetic protocol for the preparation of nanomaterials, especially metal nanoparticles is an emerging area of research in nanotechnology. These metal nanoparticles, especially silver can play a crucial role in various catalytic reactions. The biosynthesized silver nanoparticles described here was very stable up to 6 months and can be further exploited as an effective catalyst in the chemical reduction of 4-nitrophenol to 4-aminophenol. The silver nanoparticles were utilized as an efficient surface-enhanced Raman scattering (SERS) active substrate using Rhodamine 6G as Raman probe molecule. We have also carried out systematic comparative studies on the catalytic efficiency of both silver and gold nanoparticles using UV–vis spectra to monitor the above reaction spectrophotometrically. We find that the reaction follows pseudo-first order kinetics and the catalytic activity can be explained by a simple model based on Langmuir–Hinshelwood mechanism for heterogeneous catalysis. We also find that silver nanoparticles are more efficient as a catalyst compare to gold nanoparticles in the reduction of 4-nitrophenol to 4-aminophenol, which can be explained by the morphology of the nanoparticles as determined by transmission electron microscopy.

  10. The surface of Mars: Morphology and process

    Science.gov (United States)

    Aharonson, Oded

    The goal of this work is a quantitative description of the morphology of the surface of Mars, in order to constrain the nature of processes acting during the ancient past through today. Emphasis is placed on linking geometric properties to physical mechanisms. Surface smoothness on Mars is distinctive in the vast northern hemisphere plains. Amazonis Planitia is remarkable in its smoothness, exhibiting an rms variation in topography of building tectonics and volcanics. The shallower long-wavelength portion of the lowlands' topographic power spectrum relative to the highlands' can be accounted for by a simple model of sedimentation such as might be expected at an ocean's floor, but the addition of another process such as cratering is necessary to explain the spectral slope in short wavelengths. Large drainage systems on Mars have geomorphic characteristics that are inconsistent with prolonged erosion by surface runoff. We find the topography has not evolved to an expected equilibrium terrain form, even in areas where runoff incision has been previously interpreted. We demonstrate that features known as slope streaks form exclusively in regions of low thermal inertia, steep slopes, and incredibly, only where daily peak temperatures exceed 275 K during the martian year. The results suggest that at least small amounts of water may be currently present and undergo phase transitions. We detect subtle changes of the polar surface height during the course of seasonal cycles. Using altimetric crossover residuals, we show that while zonally averaged data captures the global behavior of CO 2 exchange, there is a strong dependence of the pattern on longitude. Decomposition of the signal into harmonics in time shows the amplitudes are correlated with the polar cap deposits. (Copies available exclusively from MIT Libraries, Rm. 14-0551, Cambridge, MA 02139-4307. Ph. 617-253-5668; Fax 617-253-1690.)

  11. Surface morphology and corrosion resistance of electrodeposited ...

    Indian Academy of Sciences (India)

    Administrator

    Surface morphology and corrosion resistance of electrodeposited composite coatings containing polyethylene or polythiophene in. Ni–Mo base. J NIEDBAŁA. Institute of Materials Science, University of Silesia, 40-007 Katowice, ul. Bankowa 12, Poland. MS received 11 December 2009; revised 30 April 2010. Abstract.

  12. Effect of surface morphology on the sputtering yields. II. Ion sputtering from rippled surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Makeev, Maxim A. E-mail: makeev@usc.edu; Barabasi, Albert-Laszlo E-mail: alb@nd.edu

    2004-08-01

    Off-normal ion bombardment of solid targets with energetic particles often leads to development of periodically modulated structures on the surfaces of eroded materials. Ion-induced surface roughening, in its turn, causes sputtering yield changes. We report on a comprehensive theoretical study of the effect of rippled surface morphology on the sputtering yields. The yield is computed as a function of the parameters characterizing the surface morphology and the incident ion beam, using the Sigmund's theory of ion sputtering. We find that the surface morphology development may cause substantial variations in the sputter yields, depending on a complex interplay between the parameters characterizing the ripple structure and the incident ion beam. For certain realizations of the ripple structure, the surface morphology is found to induce enhanced, relative to the flat surface value, sputtering yields. On the other hand, there exist regimes in which the sputtering yield is suppressed by the surface roughness below the flat surface result. We confront the obtained theoretical results with available experimental data and find that our model provides an excellent qualitative and, in some cases, quantitative agreement with the results of experimental studies.

  13. The influence of fabric surface characteristics on satellite bloodstain morphology.

    Science.gov (United States)

    Miles, H F; Morgan, R M; Millington, J E

    2014-07-01

    Bloodstains on fabrics such as clothing, soft furnishings or carpets are often encountered in casework. These stains often have a distinctive morphology that includes satellite stains, thought to be a highly sensitive feature that is a function of surface roughness. This study presents the findings of experimental studies conducted with proxy blood on two fabrics, similar in labeled composition, to assess the influence of fabric type on satellite stain generation. The morphology of proxy blood stains on the two fabric types were found to be statistically distinguishable from one another, with the volume of satellite stains generated being dependent upon the surface roughness of the fabric. These findings provide an initial step that illustrates the viability of providing an empirical evidence base for the interpretation of satellite stains in forensic blood pattern analysis (BPA). Copyright © 2014 Forensic Science Society. Published by Elsevier Ireland Ltd. All rights reserved.

  14. Wetting morphologies on chemically nanopatterned surfaces

    Science.gov (United States)

    Checco, Antonio; Gang, Oleg; Ocko, Benjamin M.

    2007-03-01

    We study the wetting of simple, volatile liquids on model chemical nanopatterns created using Local Oxidation Nanolithography. This technique makes use of a biased, metallic AFM tip to locally oxidize the methyl-terminations of a self-assembled monolayer (octadecylthrichlorosilane) into carboxylic acid termination[1]. With this method we have realized parallel, 50 to 500 nm wide, wettable stripes (carboxylic) embedded into a non-wettable (methyl) surface. Several organic (polar, non-polar), volatile liquids have been condensed onto the wettable stripes and the resulting droplet morphologies have been studied in-situ by using an environmental AFM. We show that close to saturation and for droplet thickness less than 10 nm long-range forces are relevant to the nanoliquid shape. These results are well described by Density Functional Theory assuming dispersive molecular interactions. In addition, we explore the dynamics of condensation/evaporation of the liquid nanodrops.

  15. Effect of surface morphology on the sputtering yields. I. Ion sputtering from self-affine surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Makeev, Maxim A. E-mail: makeev@usc.edu; Barabasi, Albert-Laszlo E-mail: alb@nd.edu

    2004-08-01

    As extensive experimental studies have shown, under certain conditions, ion bombardment of solid targets induces a random (self-affine) morphology on the ion-eroded surfaces. The rough morphology development is known to cause substantial variations in the sputtering yields. In this article, we present a theoretical model describing the sputter yields from random, self-affine surfaces subject to energetic ion bombardment. We employ the Sigmund's theory of ion sputtering, modified for the case of self-affine surfaces, to compute the sputter yields. We find that the changes in the sputtering yield, associated with the non-planar surface morphology, are strongly dependent on the parameters characterizing the surface roughness (such as the saturation width and the correlation length) and the incident ion beam (such as the incident ion energy and the deposited energy widths). It is shown that, for certain ranges of the parameters variations, surface roughness leads to substantial enhancements in the yield, with magnitude of the effect being more than 100%, as compared to the flat surface value. Furthermore, we find that, depending on the interplay between these parameters, the surface roughness can both enhance and suppress the sputter yields.

  16. Robust surface roughness indices and morphological interpretation

    Science.gov (United States)

    Trevisani, Sebastiano; Rocca, Michele

    2016-04-01

    Geostatistical-based image/surface texture indices based on variogram (Atkison and Lewis, 2000; Herzfeld and Higginson, 1996; Trevisani et al., 2012) and on its robust variant MAD (median absolute differences, Trevisani and Rocca, 2015) offer powerful tools for the analysis and interpretation of surface morphology (potentially not limited to solid earth). In particular, the proposed robust index (Trevisani and Rocca, 2015) with its implementation based on local kernels permits the derivation of a wide set of robust and customizable geomorphometric indices capable to outline specific aspects of surface texture. The stability of MAD in presence of signal noise and abrupt changes in spatial variability is well suited for the analysis of high-resolution digital terrain models. Moreover, the implementation of MAD by means of a pixel-centered perspective based on local kernels, with some analogies to the local binary pattern approach (Lucieer and Stein, 2005; Ojala et al., 2002), permits to create custom roughness indices capable to outline different aspects of surface roughness (Grohmann et al., 2011; Smith, 2015). In the proposed poster, some potentialities of the new indices in the context of geomorphometry and landscape analysis will be presented. At same time, challenges and future developments related to the proposed indices will be outlined. Atkinson, P.M., Lewis, P., 2000. Geostatistical classification for remote sensing: an introduction. Computers & Geosciences 26, 361-371. Grohmann, C.H., Smith, M.J., Riccomini, C., 2011. Multiscale Analysis of Topographic Surface Roughness in the Midland Valley, Scotland. IEEE Transactions on Geoscience and Remote Sensing 49, 1220-1213. Herzfeld, U.C., Higginson, C.A., 1996. Automated geostatistical seafloor classification - Principles, parameters, feature vectors, and discrimination criteria. Computers and Geosciences, 22 (1), pp. 35-52. Lucieer, A., Stein, A., 2005. Texture-based landform segmentation of LiDAR imagery

  17. Size dependent phase and morphological transformation of alumina nanoparticles

    Science.gov (United States)

    Dommisa, D. B.; Dash, R. K.

    2018-03-01

    The size effect of the alumina nanoparticles on the phase and morphological transition by thermal treatment at various temperatures is investigated by choosing two different sizes alumina nanoparticles. Our experimental results revealed that phase and morphological transformation behavior is significantly different for smaller size alumina nanoparticles than that of larger size. The more stable alpha phase transformation occurs at a higher temperature for smaller size alumina nanoparticles in comparison to that of the larger size alumina nanoparticles. Moreover, the experimental facts also elucidated that the nucleation and growth process at the nanoscale for the phase transition is also size dependent. Our experimental result from the FESEM and TEM analysis also revealed that there is a direct correlation between phase and morphological transition of alumina nanoparticles size which is consistent with the XRD results. Therefore, we believe that our experimental findings can be extended to other complex nanomaterials for understanding the size-dependent phase and morphological transformation at the nanoscale.

  18. Surface morphology of some articulated corallines from India

    Digital Repository Service at National Institute of Oceanography (India)

    Kerkar, V.; Iyer, S.D.

    Surface structures of seven species belonging to four genera of subfamily Corallinoidae (Fly: Corallinaceae) were microscopically investigated Two distinct surface morphologies were revealed namely a 'Corallina type' (c-type) with round to irregular...

  19. Controlling morphology in swelling-induced wrinkled surfaces

    Science.gov (United States)

    Breid, Derek Ronald

    Wrinkles represent a pathway towards the spontaneous generation of ordered surface microstructure for applications in numerous fields. Examples of highly complex ordered wrinkle structures abound in Nature, but the ability to harness this potential for advanced material applications remains limited. This work focuses on understanding the relationship between the patterns on a wrinkled surface and the experimental conditions under which they form. Because wrinkles form in response to applied stresses, particular attention is given to the nature of the stresses in a wrinkling surface. The fundamental insight gained was then utilized to account for observed wrinkle formation phenomena within more complex geometric and kinetic settings. In order to carefully control and measure the applied stresses on a wrinkling film, a swelling-based system was developed using poly(dimethylsiloxane) (PDMS), surface-oxidized with a UV-ozone treatment. The swelling of the oxidized surface upon exposure to an ethanol vapor atmosphere was characterized using beam-bending experiments, allowing quantitative measurements of the applied stress. The wrinkle morphologies were characterized as a function of the overstress, defined as the ratio of the applied swelling stress to the critical buckling stress of the material. A transition in the dominant morphology of the wrinkled surfaces from dimple patterns to ridge patterns was observed at an overstress value of ˜2. The pattern dependence of wrinkles on the ratio of the principal stresses was examined by fabricating samples with a gradient prestress. When swollen, these samples exhibited a smooth morphological transition from non-equibiaxial to equibiaxial patterns, with prestrains as low as 2.5% exhibiting non-equibiaxial characteristics. This transition was seen both in samples with low and high overstresses. To explore the impact of these stress states in more complex geometries, wrinkling hemispherical surfaces with radii of curvature

  20. Modelling and simulation of surface morphology driven by ion bombardment

    Energy Technology Data Exchange (ETDEWEB)

    Yewande, E.O.

    2006-05-02

    Non-equilibrium surfaces, at nanometer length scales, externally driven via bombardment with energetic particles are known to exhibit well ordered patterns with a variety of applications in nano-technology. These patterns emerge at time scales on the order of minutes. Continuum theory has been quite successful in giving a general picture of the processes that interplay to give the observed patterns, as well as how such competition might determine the properties of the nanostructures. However, continuum theoretical descriptions are ideal only in the asymptotic limit. The only other theoretical alternative, which happens to be more suitable for the characteristic length-and time-scales of pattern formation, is Monte Carlo simulation. In this thesis, surface morphology is studied using discrete solid-on-solid Monte Carlo models of sputtering and surface diffusion. The simulations are performed in the context of the continuum theories and experiments. In agreement with the experiments, the ripples coarsen with time and the ripple velocity exhibits a power-law behaviour with the ripple wavelength, in addition, the exponent was found to depend on the simulation temperature, which suggests future experimental studies of flux dependence. Moreover, a detailed exploration of possible topographies, for different sputtering conditions, corresponding to different materials, was performed. And different surface topographies e.g. holes, ripples, and dots, were found at oblique incidence, without sample rotation. With sample rotation no new topography was found, its only role being to destroy any inherent anisotropy in the system. (orig.)

  1. Modelling and simulation of surface morphology driven by ion bombardment

    International Nuclear Information System (INIS)

    Yewande, E.O.

    2006-01-01

    Non-equilibrium surfaces, at nanometer length scales, externally driven via bombardment with energetic particles are known to exhibit well ordered patterns with a variety of applications in nano-technology. These patterns emerge at time scales on the order of minutes. Continuum theory has been quite successful in giving a general picture of the processes that interplay to give the observed patterns, as well as how such competition might determine the properties of the nanostructures. However, continuum theoretical descriptions are ideal only in the asymptotic limit. The only other theoretical alternative, which happens to be more suitable for the characteristic length-and time-scales of pattern formation, is Monte Carlo simulation. In this thesis, surface morphology is studied using discrete solid-on-solid Monte Carlo models of sputtering and surface diffusion. The simulations are performed in the context of the continuum theories and experiments. In agreement with the experiments, the ripples coarsen with time and the ripple velocity exhibits a power-law behaviour with the ripple wavelength, in addition, the exponent was found to depend on the simulation temperature, which suggests future experimental studies of flux dependence. Moreover, a detailed exploration of possible topographies, for different sputtering conditions, corresponding to different materials, was performed. And different surface topographies e.g. holes, ripples, and dots, were found at oblique incidence, without sample rotation. With sample rotation no new topography was found, its only role being to destroy any inherent anisotropy in the system. (orig.)

  2. Variation in buccal surface morphology of deciduous first molars.

    Science.gov (United States)

    Simratvir, M; Moghe, G; Singh, D; Dhillon, K

    2012-01-01

    The buccal bulge of the deciduous first molars has always been a restorative challenge to the pediatric dentist. Morphologically it may vary from a slight prominence to a well-developed cusp-like structure. This study was conducted to determine the variable buccal surface morphology of deciduous first molar and its clinical relevance. A prospective study was conducted whereby 2016 patients visiting the outpatient clinic of dental hospital over 1 year were evaluated. Any variation in buccal surface morphology of the deciduous first molars was recorded photographically or by replicating in dental stone. Varied morphological patterns on buccal surface were observed for which a new classification scheme has been proposed. The surface morphology of deciduous teeth crowns must be studied carefully as it may be indicative of pulpal extensions and accessory roots, requiring consideration during restorative treatment planning.

  3. Investigations of the Band Structure and Morphology of Nanostructured Surfaces

    Science.gov (United States)

    Knox, Kevin R.

    2011-12-01

    In this dissertation, I examine the electronic structure of two very different types of two-dimensional systems: valence band electrons in single layer graphene and electronic states created at the vacuum interface of single crystal copper surfaces. The characteristics of both electronic systems depend intimately on the morphology of the surfaces they inhabit. Thus, in addition to discussing the respective band structures of these systems, a significant portion of this dissertation will be devoted to measurements of the surface morphology of these systems. Free-standing exfoliated monolayer graphene is an ultra-thin flexible membrane and, as such, is known to exhibit large out-of-plane deformation due to substrate and adsorbate interaction as well as thermal vibrations and, possibly, intrinsic buckling. Such crystal deformation is known to limit mobility and increase local chemical reactivity. Additionally, deformations present a measurement challenge to researchers wishing to determine the band structure by angle-resolved photoemission since they limit electron coherence in such measurements. In this dissertation, I present low energy electron microscopy and micro probe diffraction measurements, which are used to image and characterize corrugation in SiO2-supported and suspended exfoliated graphene at nanometer length scales. Diffraction line-shape analysis reveals quantitative differences in surface roughness on length scales below 20 nm which depend on film thickness and interaction with the substrate. Corrugation decreases with increasing film thickness, reflecting the increased stiffness of multilayer films. Specifically, single-layer graphene shows a markedly larger short range roughness than multilayer graphene. Due to the absence of interactions with the substrate, suspended graphene displays a smoother morphology and texture than supported graphene. A specific feature of suspended single-layer films is the dependence of corrugation on both adsorbate load

  4. Tunable electrochemical preparation of cobalt micro/nanostructures and their morphology-dependent wettability property

    International Nuclear Information System (INIS)

    Qiu Ri; Zhang Dun; Wang Peng; Zhang Xiaoli; Kang, Young Soo

    2011-01-01

    Graphical abstract: Versatile cobalt micro/nanostructures are achieved via a facile electrochemical growth approach. Based on the structures grown at various potential, a morphology-dependent wettability fashion exhibits from hydrophilicity to superhydrophobicity and superhydrophilicity. Highlights: ► Versatile cobalt micro/nanostructures are prepared via electrochemical method. ► Cobalt crystal morphology is highly impacted by external potential. ► Morphology-dependent wettability of cobalt structures exhibits hydrophilicity, superhydrophobicity and superhydrophilicity. - Abstract: A versatile cobalt micro/nanostructure preparation method via a facile electrochemical growth approach is reported in this study. Based on the existing theoretical analysis, the various crystal growth parameters, including the potential, concentration and temperature, act as parameters to impact the metallic crystal growth rate and the resultant morphology. These parameters were varied to elucidate the growth rate and morphology changes. Electron microscopy technique was applied to reveal the corresponding crystal morphology, which demonstrates that the potential can consequently impact the crystal shapes formed, from bump to flower and dendrite shapes. However, in the current experiments, the morphology achieved by changing the concentration and temperature was a dendritic structure, which suggests that the growth conditions promoted a dendritic structure formation regime. Based on the structures grown at various potentials, without further surface modifications, a morphology-dependent wettability trend exhibited from the superhydrophobic to superhydrophilic structures. The superhydrophobicity stems from the small contact areas of the tips of the flower-like structure. Meanwhile, the superhydrophilicity is due to the nanometer-scale channels existing in the hierarchical structures of the dendritic crystals, in which the capillary effect draws water droplets to spread on the

  5. Effects of methamphetamine dependence and HIV infection on cerebral morphology

    DEFF Research Database (Denmark)

    Jernigan, Terry Lynne; Gamst, Abthony C; Archibald, Sarah L.

    2005-01-01

    OBJECTIVE: The authors examined the separate and combined effects of methamphetamine dependence and HIV infection on brain morphology. METHOD: Morphometric measures obtained from magnetic resonance imaging of methamphetamine-dependent and/or HIV-positive participants and their appropriate age......- and education-matched comparison groups were analyzed. Main effects of age, HIV infection, methamphetamine dependence, and the interactions of these factors were examined in analyses of cerebral gray matter structure volumes. RESULTS: Independent of the effect of age, HIV infection was associated with reduced...... volumes of cortical, limbic, and striatal structures. There was also some evidence of an interaction between age and HIV infection such that older HIV-positive participants suffered disproportionate loss. Methamphetamine dependence was surprisingly associated with basal ganglia and parietal cortex volume...

  6. Reactive solid surface morphology variation via ionic diffusion.

    Science.gov (United States)

    Sun, Zhenchao; Zhou, Qiang; Fan, Liang-Shih

    2012-08-14

    In gas-solid reactions, one of the most important factors that determine the overall reaction rate is the solid morphology, which can be characterized by a combination of smooth, convex and concave structures. Generally, the solid surface structure varies in the course of reactions, which is classically noted as being attributed to one or more of the following three mechanisms: mechanical interaction, molar volume change, and sintering. Here we show that if a gas-solid reaction involves the outward ionic diffusion of a solid-phase reactant then this outward ionic diffusion could eventually smooth the surface with an initial concave and/or convex structure. Specifically, the concave surface is filled via a larger outward diffusing surface pointing to the concave valley, whereas the height of the convex surface decreases via a lower outward diffusion flux in the vertical direction. A quantitative 2-D continuum diffusion model is established to analyze these two morphological variation processes, which shows consistent results with the experiments. This surface morphology variation by solid-phase ionic diffusion serves to provide a fourth mechanism that supplements the traditionally acknowledged solid morphology variation or, in general, porosity variation mechanisms in gas-solid reactions.

  7. The surface of Io - Geologic units, morphology, and tectonics

    Science.gov (United States)

    Schaber, G. G.

    1980-09-01

    The geologic units, morphology and tectonics evident on a preliminary geological map obtained from best-resolution Voyager 1 images and a preliminary pictorial map of the surface of Io are discussed. Nine volcanic units are identified on the surface which are composed of mountain materials, intervent, layered and eroded layered plains, and wall and floor, pit crater flow, shield crater flow, fissure flow and crater cone units associated with volcanic vents, along with seven types of structural features. The cumulative volcanic crater size distribution of 170 Ionian vents with craters greater than 14 km is similar to that of impact craters on other solar system bodies, with a surplus of small craters and a preponderance of volcanic vents in the Io equatorial zone. The observed surface morphologies provide evidence for a mixture of silicates and sulfur as the dominant surface material. Lineaments and grabens are also apparent on the surface, in a common planetary grid pattern.

  8. Cell behavior on microparticles with different surface morphology

    Energy Technology Data Exchange (ETDEWEB)

    Huang Sha [Wound Healing and Cell Biology Laboratory, Institute of Basic Medical Sciences, General Hospital of PLA, Beijing 100853 (China); Fu Xiaobing, E-mail: fuxiaobing@vip.sina.co [Wound Healing and Cell Biology Laboratory, Institute of Basic Medical Sciences, General Hospital of PLA, Beijing 100853 (China); Burns Institute, The First Affiliated Hospital, General Hospital of PLA, Trauma Center of Postgraduate Medical College, Beijing 100037 (China)

    2010-03-18

    Microparticles can serve as substrates for cell amplification and deliver the cell aggregation to the site of the defect for tissue regeneration. To develop favorable microparticles for cell delivery application, we fabricated and evaluated three types of microparticles that differ in surface properties. The microparticles with varied surface morphology (smooth, pitted and multicavity) were created from chemically crosslinked gelatin particles that underwent various drying treatments. Three types of microparticles were characterized and assessed in terms of the cell behavior of human keratinocytes and fibroblasts seeded on them. The cells could attach, spread and proliferate on all types of microparticles but spread and populated more slowly on the microparticles with smooth surfaces than on those with pitted or multicavity surfaces. Microparticles with a multicavity surface demonstrated the highest cell attachment and growth rate. Furthermore, cells tested on microparticles with a multicavity surface exhibited better morphology and induced the earlier formation of extracellular-based cell-microparticle aggregation than those on microparticles with other surface morphology (smooth and pitted). Thus, microparticles with a multicavity surface show promise for attachment and proliferation of cells in tissue engineering.

  9. Glucagon Amyloid-like Fibril Morphology Is Selected via Morphology-Dependent Growth Inhibition

    DEFF Research Database (Denmark)

    Andersen, C.B.; Otzen, D.; Christiansen, Gunna

    2007-01-01

    Protein Structure and Biophysics, Novo Nordisk A/S, Novo Nordisk Park, DK-2760 Malov, Denmark, Centre for Insoluble Protein Structures (inSPIN), Department of Life Sciences, Aalborg University, Sohngaardsholmsvej 49, DK-9000 Aalborg, Denmark, and Institute of Medical Microbiology and Immunology...... twisted fibril seeds cannot grow at high concentrations. We conclude that there exists a morphology-dependent mechanism for inhibition of glucagon fibril growth. Light scattering experiments indicate that glucagon is mainly monomeric below 1 mg/mL and increasingly trimeric above this concentration. We...

  10. Surface roughness and morphologic changes of zirconia: Effect of ...

    African Journals Online (AJOL)

    Purpose: The purpose of this study was to investigate the surface roughness and morphologic changes of pre.sintered ZrO2 after sandblasting and erbium, chromium: Yttrium, scandium, gallium, garnet (Er, Cr: YSGG) laser application of different intensities. Material and Methods: Eighty pre-sintered ZrO2 cylinders (7 mm ...

  11. Morphology of Myoepithelium and Basal Surface of the Glandular ...

    African Journals Online (AJOL)

    Broad Objective: To study the morphology of the myoepithelial cells and the basal surfaces of the glandular cells in the small and large lobes of the Harderian gland. Study Setting and Methodology: The study used the scanning electron and lesser confocal microscopes to observe the Harderian gland of the golden hamster.

  12. Influence of deposition rate on PL spectrum and surface morphology ...

    Indian Academy of Sciences (India)

    Influence of deposition rate on PL spectrum and surface morphology of ZnO nanolayers deposited on Si (100) substrate. A ZENDEHNAM. ∗. , M MIRZAEE and S MIRI. Thin Film Laboratory, Department of Physics, Faculty of Science, Arak University, Arak 38156-8-8349, Iran. MS received 26 March 2012; revised 5 May 2012.

  13. Surface morphology of amygdala is associated with trait anxiety.

    Directory of Open Access Journals (Sweden)

    Shuyu Li

    Full Text Available Previous neuroimaging studies have suggested a role of amygdala in trait anxiety level, in which amygdala was typically treated as a whole. To date, it remains unknown whether the morphology of specific subregions of amygdala are associated with trait anxiety. Here, we employed a shape analysis approach to locate the association between its morphology and trait anxiety on the surface of amygdala. 24 healthy young participants were included. The boundary of amygdala for each subject was first manually outlined using high-resolution magnetic resonance (MR image, followed by 3D surface reconstruction and parameterization using spherical harmonic description. Two point-wise metrics, direct displacement between the individual surface and atlas surface and its normal projection, were used to quantify the surface morphology of amygdala. Statistical analysis revealed significant correlations between the two surface metrics and trait anxiety levels, which were located around the lateral and central nucleus of right amygdala. Our results provided localized information for the association between amygdala and trait anxiety, and suggested a central role of the lateral and central nucleus of right amygdala on trait anxiety.

  14. Morphology-dependent enhancement of the pseudocapacitance of template-guided tunable polyaniline nanostructures

    KAUST Repository

    Chen, Wei

    2013-07-25

    Polyaniline is one of the most investigated conducting polymers as supercapacitor material for energy storage applications. The preparation of nanostructured polyaniline with well-controlled morphology is crucial to obtaining good supercapacitor performance. We present here a facile chemical process to produce polyaniline nanostructures with three different morphologies (i.e., nanofibers, nanospheres, and nanotubes) by utilizing the corresponding tunable morphology of MnO2 reactive templates. A growth mechanism is proposed to explain the evolution of polyaniline morphology based on the reactive templates. The morphology-induced improvement in the electrochemical performance of polyaniline pseudocapacitors is as large as 51% due to the much enhanced surface area and the porous nature of the template-guided polyaniline nanostructures. In addition, and for the first time, a redox-active electrolyte is applied to the polyaniline pseudocapacitors to achieve significant enhancement of pseudocapacitance. Compared to the conventional electrolyte, the enhancement of pseudocapacitance in the redox-active electrolyte is 49%-78%, depending on the specific polyaniline morphology, reaching the highest reported capacitance of 896 F/g for polyaniline full cells so far. © 2013 American Chemical Society.

  15. Tribological behaviors of UHMWPE composites with different counter surface morphologies

    Science.gov (United States)

    Wang, Yanzhen; Yin, Zhongwei; Li, Hulin; Gao, Gengyuan

    2017-12-01

    The influence of counter surface morphologies on hybrid glass fiber (GF) and carbon fiber (CF) filled ultrahigh molecular weight polyethylene (UHMWPE) were studied under various contact pressure and sliding speed against GCr15 steel in dry condition. The goals were to investigate the tribological behavior of GF/CF/UHMWPE composite as a kind of water lubricated journal bearing material. The friction and wear behavior of composites were examined using a pin-on-disc tribometer. The morphologies of the worn surface were examined by scanning electron microscopy (SEM) and laser 3D micro-imaging and profile measurement. Generally, the wear rate and friction coefficient of composites increase as the increment of counter surface roughness. The friction coefficient increases firstly and then decrease with an increase in sliding speed and contact pressure for counterface with Ra=0.2 and 3.5 μm, while the friction coefficient decreased for counterface with Ra=0.6 μm.

  16. AFM surface morphology investigation of ion beam modified polyimide

    Science.gov (United States)

    Švorčík, V.; Arenholz, E.; Rybka, V.; Hnatowicz, V.

    1997-03-01

    Polyimide Upilex R was irradiated with 90 keV N + ions to the fluences of 1 × 10 14-2 × 10 17 cm -2. The surface morphology and the structure of the ion beam modified PI were examined using atomic force microscopy and X-ray difraction. Sheet resistance as a function of the ion fluence and the sample temperature was measured by standard two point technique. Significant changes of the surface morphology and production of graphitic phase in the sample surface layer modified by the ion irradiation were observed. Strong decrease of the sheet resistance (by 11 orders of magnitude) in the ion beam modified samples is connected with progressive carbonization and graphitization of the degraded polymer. Electrical charge transport is mediated by variable-range hopping mechanism. Drastic structural changes initiated by the ion irradiation to high fluences are similar to those observed in polymer pyrolysis.

  17. Multiscale analysis of surface morphologies by curvelet and contourlet transforms

    International Nuclear Information System (INIS)

    Li, Linfu; Zhang, Xiangchao; Zhang, Hao; He, Xiaoying; Xu, Min

    2015-01-01

    The surface topographies of precision components are critical to their functionalities. However, it is challenging to characterize the topographies of complex surfaces, especially for structured surfaces. The wavelet families are promising for the multiscale geometry analysis of nonstochastic surfaces. The second-generation curvelet transform provides a sparse representation and good multiscale decomposition for curve singularities. However, the contourlet expansion, composed of bases oriented along various directions in multiple scales with smaller redundancy rates, has a remarkable capability of representing borderlines. In this paper they are both adopted for the characterization of surface topographies. Different components can be extracted according to their scales and morphological characteristics; as a result, the corresponding manufacturing processes and functionalities can be analyzed specifically. Numerical experiments are given to demonstrate the capabilities of these methods in sparse representation and effective extraction of geometry features of different nonstochastic surfaces. (paper)

  18. Morphology-dependent space charge polarization and dielectric relaxation of CdO nanomorphotypes

    Directory of Open Access Journals (Sweden)

    Paulose Thomas

    2016-12-01

    Full Text Available A versatile approach signifying the morphology-dependent dielectric polarization and relaxation mechanisms of cadmium oxide (CdO nanosphere, nanoflakes and nanoparallelepiped morphotypes as a function of frequency and temperature is presented. Variation of dielectric property is observed due to the changes of space charge/interfacial polarization resulting from the variations of surface to volume ratio of nanomorphology. Accordingly, colossal dielectric constant value has been observed in CdO nanosphere having larger surface to volume ratio. The order of dielectric constant (dc values observed for the present nanomorphologies is: dc of sphere > dc of flakes > dc of parallelepiped resembles the order of surface to volume ratios of the present morphologies respectively. The experimental data of complex impedance values are numerically fitted using theoretical models which provide the information of role of grain resistance on dielectric polarization and Cole–Cole type mechanism of dielectric relaxation process. The activation energies for electron transport are found to be 0.087eV for spheres, 0.074eV for flakes and 0.067 for parallelepiped nanomorphotypes of CdO. The dielectric and impedance spectroscopic analysis of the present material opens up wide scope for morphology-dependent tuning of nanomaterials for electrical applications.

  19. Surface dependency in thermodynamics of ideal gases

    International Nuclear Information System (INIS)

    Sisman, Altug

    2004-01-01

    The Casimir-like size effect rises in ideal gases confined in a finite domain due to the wave character of atoms. By considering this effect, thermodynamic properties of an ideal gas confined in spherical and cylindrical geometries are derived and compared with those in rectangular geometry. It is seen that an ideal gas exhibits an unavoidable quantum surface free energy and surface over volume ratio becomes a control variable on thermodynamic state functions in microscale. Thermodynamics turns into non-extensive thermodynamics and geometry difference becomes a driving force since the surface over volume ratio depends on the geometry

  20. Dynamic and reversible surface topography influences cell morphology.

    Science.gov (United States)

    Kiang, Jennifer D; Wen, Jessica H; del Álamo, Juan C; Engler, Adam J

    2013-08-01

    Microscale and nanoscale surface topography changes can influence cell functions, including morphology. Although in vitro responses to static topography are novel, cells in vivo constantly remodel topography. To better understand how cells respond to changes in topography over time, we developed a soft polyacrylamide hydrogel with magnetic nickel microwires randomly oriented in the surface of the material. Varying the magnetic field around the microwires reversibly induced their alignment with the direction of the field, causing the smooth hydrogel surface to develop small wrinkles; changes in surface roughness, ΔRRMS , ranged from 0.05 to 0.70 μm and could be oscillated without hydrogel creep. Vascular smooth muscle cell morphology was assessed when exposed to acute and dynamic topography changes. Area and shape changes occurred when an acute topographical change was imposed for substrates exceeding roughness of 0.2 μm, but longer-term oscillating topography did not produce significant changes in morphology irrespective of wire stiffness. These data imply that cells may be able to use topography changes to transmit signals as they respond immediately to changes in roughness. Copyright © 2013 Wiley Periodicals, Inc.

  1. Interaction of energetic particles with polymer surfaces: surface morphology development and sputtered polymer-fragment ion analysis

    International Nuclear Information System (INIS)

    Michael, R.S.

    1987-01-01

    The core of this thesis is based on a series of papers that have been published or will soon be published in which the various processes taking place in the energetic particle-polymer surface interaction scene is investigated. Results presented show different developments on polymer surfaces when compared to the vast experimental data on energetic particle-metal surface interactions. The surface morphology development depends on the physical characteristics of the polymer. Sputtering yields of fluoropolymers were several orders higher than the sputtering yields of aliphatic and aromatic polymers. Depending on the chemical nature of the polymer, the surface morphology development was dependent upon the extent of radiation-damage accumulation. Fast Atom Bombardment Mass Spectrometry at low and high resolution was applied to the characterization of sputtered polymer fragment ions. Fragment ions and their intensities were used to identify polymer samples, observe radiation damage accumulation and probe polymer-polymer interface of a polymer-polymer sandwich structure. A model was proposed which attempts to explain the nature of processes involved in the energetic particle-polymer surface interaction region

  2. Laser treatment of boron carbide surfaces: Metallurgical and morphological examinations

    Energy Technology Data Exchange (ETDEWEB)

    Yilbas, B.S., E-mail: bsilbas@kfupm.edu.sa; Karatas, C.

    2014-08-01

    Highlights: • Dense layer with fine grains is formed at surface. • Irregular shaped grains and dendrites are formed below dense layer. • Assisting gas forms nitride species (BN and BC{sub 2}N) at surface. • Fracture toughness of treated surface reduces because of high hardness. • Residual stress is compressive and the maximum residual stress is about 0.9 GPa. - Abstract: Laser treatment of B{sub 4}C tile surfaces is carried out under high pressure nitrogen assisting gas environment. Morphological and metallurgical changes in the laser treated layer are examined by incorporating scanning electron microscope, energy dispersive spectroscopy, and X-ray diffraction. Microhardness and fracture toughness of the laser treated surface are determined from the indentation data. Residual stress formed at the treated surface is obtained by using X-ray diffraction technique. It is found that laser treated surface is free from large scale asperities including cracks and voids; however, some locally scattered shallow cavities with 1.5–2 μm widths are formed at the surface because of high temperature processing. Dense layer, consisting of fine grains, and formation of nitride species (BN and BC{sub 2}N) enhance microhardness and lower fracture toughness at the surface. Residual stress formed in the treated layer is compressive and the maximum residual stress is in the order of −0.9 GPa.

  3. Effect of alkali treatment on surface morphology of titanium

    Energy Technology Data Exchange (ETDEWEB)

    Tan, K. J., E-mail: gd130056@siswa.uthm.edu.my; Wahab, M. A. A., E-mail: cd110006@siswa.uthm.edu.my; Mahmod, S., E-mail: cd110201@siswa.uthm.edu.my; Idris, M. I., E-mail: izwana@uthm.edu.my; Abdullah, H. Z., E-mail: hasan@uthm.edu.my [Faculty of Mechanical and Manufacturing Engineering, Universiti Tun Hussein Onn Malaysia, 86400 Parit Raja, Batu Pahat, Johor (Malaysia)

    2015-07-22

    Alkali and heat treatments were first introduced by Kim et al. to prepare a bioactive surface on titanium. This method has been proven very effective and widely used in other studies to promote titanium osteointegration. This study aims to investigate further the effect of alkali treatment on surface morphology of high purity titanium. High purity titanium foils were immersed in NaOH aqueous solutions of 0.5 M, 5 M and 15 M at 60°C and 80 °C for 1, 3 and 7 days. The surface morphology was examined using Field Emission Scanning Electron Microscope (FESEM). The obtained phases were analysed using Fourier Transform Infrared Spectroscopy (FTIR) in the spectra range of 4000-600 cm{sup −1} at 4 cm{sup −1} resolution and 50 scans. At the same soaking temperature and soaking time, a thicker porous network was observed with increasing concentration of NaOH. At the same soaking temperature, a much porous structure was observed with increasing soaking time. At constant alkali concentration, more homogenously distributed porous surface structure was observed with increasing soaking temperature.

  4. Problems of surface morphology and layer deposition during plasma etching processes. 2

    International Nuclear Information System (INIS)

    Tiller, H.-J.; Krausse, J.; Voigt, R.

    1982-01-01

    The plasma etching of Si in CF 4 -, CF 4 /O 2 - and CF 4 /H 2 plasmas was investigated in dependence on the etching gas, the plasma conditions (pressure, power density) and etching time in different reactors. A roughening of the surface and the formation of a 'semi-amorphous' surface layer with a powder-like morphology was detected by TEM-and RHEED methods. It is supposed that the surface layer has a fundamental consequence as an intermediate state in the etching mechanism. (author)

  5. IR and UV laser-induced morphological changes in silicon surface under oxygen atmosphere

    Energy Technology Data Exchange (ETDEWEB)

    Jimenez-Jarquin, J.; Fernandez-Guasti, M.; Haro-Poniatowski, E.; Hernandez-Pozos, J.L. [Laboratorio de Optica Cuantica, Departamento de Fisica, Universidad Autonoma Metropolitana-Iztapalapa, Av. San Rafael Atlixco No. 186, Col. Vicentina, C.P. 09340, Mexico D.F. (Mexico)

    2005-08-01

    We irradiated silicon (100) wafers with IR (1064 nm) and UV (355 nm) nanosecond laser pulses with energy densities within the ablation regime and used scanning electron microscopy to analyze the morphological changes induced on the Si surface. The changes in the wafer morphology depend both on the incident radiation wavelength and the environmental atmosphere. We have patterned Si surfaces with a single focused laser spot and, in doing the experiments with IR or UV this reveals significant differences in the initial surface cracking and pattern formation, however if the experiment is carried out in O{sub 2} the final result is an array of microcones. We also employed a random scanning technique to irradiate the silicon wafer over large areas, in this case the microstructure patterns consist of a ''semi-ordered'' array of micron-sized cones. (copyright 2005 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  6. The morphology of coconut fiber surface under chemical treatment

    OpenAIRE

    Arsyad, Muhammad; Wardana, I Nyoman Gede; Pratikto,; Irawan, Yudy Surya

    2015-01-01

    The objective of this study was to determine the effect of chemical treatment on the coconut fiber surface morphology. This study is divided into three stages, preparation of materials, treatment and testing of coconut fiber. The first treatment is coconut fiber soaked in a solution of NaOH for 3 hours with concentration, respectively 5%, 10%, 15%, and 20%. The second treatment is coconut fiber soaked in KMnO4 solution with a concentration of 0.25%, 0.5%, 0.75%, and 1% for 3 hours. The third ...

  7. Helium effects on tungsten surface morphology and deuterium retention

    International Nuclear Information System (INIS)

    Ueda, Y.; Peng, H.Y.; Lee, H.T.; Ohno, N.; Kajita, S.; Yoshida, N.; Doerner, R.; De Temmerman, G.; Alimov, V.; Wright, G.

    2013-01-01

    Recent experimental results on tungsten surface morphology, especially nano-structure (fuzz), induced by helium plasma exposure at temperatures between 1000 K and 2000 K are reviewed. This structure was firstly reported in 2006. In this review, most of experimental results reported so far including characteristics and formation conditions of the nano-structure in both linear plasma devices and magnetic confinement devices, erosion and arcing by steady-state plasma exposure and ELM-like pulsed heat or pulsed plasma exposure by a laser and a plasma gun are summarized. In addition, He effects on D retention under simultaneous D/He irradiation on tungsten are presented

  8. Surface morphology effects in a vibration based triboelectric energy harvester

    Science.gov (United States)

    Nafari, A.; Sodano, H. A.

    2018-01-01

    Despite the abundance of ambient mechanical energy in our environment, it is often neglected and left unused. However, recent studies have demonstrated that mechanical vibrations can be harvested and used to power small wireless electronic devices, such as micro electromechanical sensors (MEMS) and actuators. Most commonly, these energy harvesters convert vibration into electrical energy by utilizing piezoelectric, electromagnetic or electrostatic effects. Recently, triboelectric based energy harvesters have shown to be among the simplest and most cost-effective techniques for scavenging mechanical energy. The basis of triboelectric energy harvesters is the periodic contact and separation of two surfaces with opposite triboelectric properties which results in induced charge flow through an external load. Here, a vibration driven triboelectric nanogenerator (TENG) is fabricated and the effect of micro/nano scale surface modification is studied. The TENG produces electrical energy on the basis of periodic out-of-plane charge separation between gold and polydimethylsiloxane (PDMS) with opposite triboelectric charge polarities. By introducing micro/nano scale surface modifications to the PDMS and gold, the TENG’s power output is further enhanced. This work demonstrates that the morphology of the surfaces in a TENG device is important and by increasing the effective surface area through micro/nano scale modification, the power output of the device can increase by 118%. Moreover, it is shown that unlike many TENGs proposed in the literature, the fabricated device has a high RMS open circuit voltage and short circuit current and can perform for an extended period of time.

  9. Morphology and electronic properties of silicon carbide surfaces

    Science.gov (United States)

    Nie, Shu

    2007-12-01

    monitored using low-energy electron diffraction (LEED) and Auger electron spectroscopy, and the morphology of the graphitized surface is studied using AFM and STM. Use of H-etched SiC substrates enables a relatively flat surface morphology, although residual steps remain due to unintentional miscut of the wafers. Additionally, some surface roughness in the form of small pits is observed, possibly due to the fact that the surface treatments (H-etching and UHV annealing) having been performed in separate vacuum chambers with an intervening transfer through air. Field-effect transistors have been fabricated with our graphene layers; they show a relatively strong held effect at room temperature, with an electron mobility of 535 cm 2/Vs. This value is somewhat lower than that believed to be theoretically possible for this material, and one possible reason may be the nonideal morphology of the surface (i.e. because of the observed steps and pits). Tunneling spectra of the graphene reveal semi-metallic behavior, consistent with that theoretically expected for an isolated layer of graphene. However, additional discrete states are observed in the spectra, possibly arising from bonding at the graphene/SiC interface. The observation of these states provides important input towards an eventual determination of the complete interface structure, and additionally, such states may be relevant in determining the electron mobility of the graphene. Stepped vicinal SIC{0001} substrates are useful templates for epitaxial growth of various types of layers: thick layers of compound semiconductor (in which the steps help preserving the stacking arrangement in the overlayer), monolayers of graphene, or submonolayer semiconductor layers that form quantum wires along the step edges. Step array produced by H-etching of vicinal SiC (0001) and (0001¯) with various miscut angles have been studied by AFM. H-etching is found to produce full unit-cell-high steps on the (0001) Si-face surfaces, but half

  10. Tailorable Surface Morphology of 3D Scaffolds by Combining Additive Manufacturing with Thermally Induced Phase Separation.

    Science.gov (United States)

    Di Luca, Andrea; de Wijn, Joost R; van Blitterswijk, Clemens A; Camarero-Espinosa, Sandra; Moroni, Lorenzo

    2017-08-01

    The functionalization of biomaterials substrates used for cell culture is gearing towards an increasing control over cell activity. Although a number of biomaterials have been successfully modified by different strategies to display tailored physical and chemical surface properties, it is still challenging to step from 2D substrates to 3D scaffolds with instructive surface properties for cell culture and tissue regeneration. In this study, additive manufacturing and thermally induced phase separation are combined to create 3D scaffolds with tunable surface morphology from polymer gels. Surface features vary depending on the gel concentration, the exchanging temperature, and the nonsolvent used. When preosteoblasts (MC-3T3 cells) are cultured on these scaffolds, a significant increase in alkaline phosphatase activity is measured for submicron surface topography, suggesting a potential role on early cell differentiation. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  11. Couple of biomimetic surfaces with different morphologies for remanufacturing nonuniform wear rail surface

    Science.gov (United States)

    Sui, Qi; Zhou, Hong; Yang, Lin; Zhang, Haifeng; Feng, Li; Zhang, Peng

    2018-02-01

    In this work, biomimetic laser treatment was performed on repairing and remanufacturing the nonuniform worn rail surface. The wearing depth distribution of three work regions of a failure rail surface was discussed, and different thickness hardening layers with different microstructure, microhardness and wear resistances were detected from the worm surfaces. Varying wear resistances of the surfaces with different biomimetic morphologies were obtained by biomimetic laser treatments, and the corresponding effect on the lubrication sliding wear of treated and untreated surfaces were studied for comparative study. In addition, the relationship between wear resistance and the spacing of units was also provided, which can lay the important theoretical foundation for avoiding the wear resistance of the serious worn surface is less than that of the slight worn surface in the future practical applications.

  12. Controllable surface morphology and properties via mist polymerization on a plasma-treated polymethyl methacrylate surface.

    Science.gov (United States)

    Wan, S J; Wang, L; Xu, X J; Zhao, C H; Liu, X D

    2014-02-14

    Surface modification by grafting polymers on solid materials is an important strategy used to improve surface properties. This article reports that under appropriate conditions, very thin layers with desired morphologies may be constructed on a plasma-treated substrate by feeding a small quantity of a monomer with a mist stream carrying droplets produced from monomer solutions. We investigate the effects of process parameters that affect layer morphology, including exposure time to the mist stream, concentration of the monomer solution, and solvent selectivity. For a methyl methacrylate solution in ethanol, nanoparticles are uniformly grown with increasing monomer concentration or exposure time and finally form a porous layer at 3.65 mol L(-1) for 30 min. Decreasing solvent polarity not only affects surface morphology, but also increases hydrophobicity of the resulting surface. With 2,2,3,4,4,4-hexafluorobutyl methacrylate as the monomer, SEM and AFM micrographs indicated that mist polymerization results in numerous microspheres on the activated surface. These experimental results were interpreted by a mechanism in terms of an in situ polymerization accompanied by a phase transformation of the resulting polymer. Specifically, plasma treatment provides highly active cations and radicals to initiate very rapid polymerization, and the resulting polymers are consequently deposited from the liquid onto the surface under phase transition mechanisms.

  13. Modulation of structure, morphology and wettability of polytetrafluoroethylene surface by low energy ion beam irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Atta, Ali; Fawzy, Yasser H.A. [Radiation Physics Department, National Center for Radiation Research and Technology (NCRRT), Egyptian Atomic Energy Authority (EAEA) (Egypt); Bek, Alpan, E-mail: bek@metu.edu.tr [Physics Department, Middle East Technical University (METU), Ankara (Turkey); Abdel-Hamid, Hassan M. [Diagnostic Radiology Department, Applied Medical Sciences Faculty, Jazan University (Saudi Arabia); El-Oker, Mohamed M. [Physics Department, Faculty of Science, Al-Azhar University, Cairo (Egypt)

    2013-04-01

    Polytetrafluoroethylene (PTFE) films were irradiated under vacuum with 3 keV Argon ions (Ar{sup +}) and fluences ranging from 0.5 × 10{sup 18} to 2 × 10{sup 18} ions/cm{sup 2}. Ion induced PTFE surface modifications of structural, morphological and wettability nature were studied by means of Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy, atomic force microscopy and force spectroscopy, and contact angle measurements. FTIR analysis indicated defluorination of PTFE due to the rupture of C–C and C–F bonds. The values of droplet contact angle of the irradiated samples decreased gradually with the increasing ion flux, and were found to be very sensitive to the environmental humidity under which the measurements were made. The experimental results show that the surface chemical bond, morphology, and wettability of irradiated PTFE samples depend closely on the argon ion flux.

  14. MORPHOLOGICAL ADJUSTMENTS OF THE RADIAL NERVE ARE INTENSITY-DEPENDENT

    Directory of Open Access Journals (Sweden)

    Patrícia Oliva Carbone

    Full Text Available ABSTRACT Introduction: Peripheral nerve adaptation is critical for strength gains. However, information about intensity effects on nerve morphology is scarce. Objective: To compare the effects of different intensities of resistance training on radial nerve structures. Methods: Rats were divided into three groups: control (GC, training with 50% (GF1 and training 75% (GF2 of the animal’s body weight. The morphological analysis of the nerve was done by light and transmission electron microscopy. One-way ANOVA and the Tukey’s post hoc test were applied and the significance level was set at p≤0.05. Results: Training groups had an increase of strength compared to GC (p≤0.05. All measured nerve components (mean area and diameter of myelin fibers and axons, mean area and thickness of the myelin sheath, and of neurofilaments and microtubules were higher in GF2 compared to the other (p≤0.05. Conclusion: Results demonstrated greater morphological changes on radial nerve after heavier loads. This can be important for rehabilitation therapies, training, and progression.

  15. Surface and morphological features of laser-irradiated silicon under vacuum, nitrogen and ethanol

    Energy Technology Data Exchange (ETDEWEB)

    Hayat, Asma, E-mail: asmahayat@gcu.edu.pk; Bashir, Shazia; Akram, Mahreen; Mahmood, Khaliq; Iqbal, Muhammad Hassan

    2015-12-01

    dependent upon the laser fluence as well as environmental conditions. The difference in surface morphology is attributable to cooling, confinement and shielding effects as well as difference in plasma temperature, density and pressure of environmental media that corresponds to different energy deposition to the target surface. Raman spectroscopy shows that no new bands are identified in case of ablation in all three environments. However, a significant Raman shift is observed which is attributed to laser-induced stresses.

  16. Habitat preference of Zoantharia genera depends on host sponge morphology

    Directory of Open Access Journals (Sweden)

    Alberto Acosta

    2010-08-01

    Full Text Available Studies about sponge-zoanthid symbioses have been focused on understanding the specificity of the association, rather thantesting what are the characteristics that make the host suitable to be colonized. For the first time it is investigated whether the ZoanthariaParazoanthus and Epizoanthus preference is related to the host sponge morphology (shape and mechanical resistance. Materials andmethods. Sponges were categorized according to their shape and mechanical resistance. The presence/absence of zoanthids was recordedin 1,068 sponges at San Andres Island, and their habitat preference was evaluated using indices and confidence intervals. Results. 85Parazoanthus colonies (78% of the total associations and 24 Epizoanthus colonies (22% were associated to sponges (10.2% in total.Parazoanthus uses branched and compressible sponges although prefers encrusting and fragile sponges, while Epizoanthus showes theopposite pattern, it can inhabit encrusting and fragile sponges but prefers branched and compressible sponges. Conclusion. These resultsindicated that sponge morphology is an important trait in zoanthid habitat selection. On the other hand, the similarity in the habitat used byzoanthids suggests the possibility of inter-generic competition if common resources are limited in time and space, while the differentialhabitat preference allows the competitive coexistence of both genera.

  17. Might short term rockglacier surface morphological changes be attributed to permafrost degradation ?

    Science.gov (United States)

    Perrier, Romain; Cossart, Etienne; Fort, Monique

    2015-04-01

    kinematics data show that surface morphological changes are heterogeneously distributed despite rockglacier small area (0.1 km²); these changes seem to depend on ground ice nature and distribution. Two main behaviors can be highlighted: (i) Ice-cored rockglacier where ground massive ice has been identified is affected by an important surface lowering associated with thermokarst, depressions and melt furrows features. (ii) Ice-cemented rockglacier is characterized by less pronounced activity where both horizontal and vertical movement range within few centimeters. Significant surface morphological changes have not been observed. We interpret the observed short term surface morphological changes of the Lac Rouge rockglacier as the melting of massive ground ice - most likely inherited from the LIA period - rather than to permafrost degradation.

  18. Facet Model and Mathematical Morphology for Surface Characterization

    Energy Technology Data Exchange (ETDEWEB)

    Abidi, B.R.; Goddard, J.S.; Hunt, M.A.; Sari-Sarraf, H.

    1999-11-13

    This paper describes an algorithm for the automatic segmentation and representation of surface structures and non-uniformities in an industrial setting. The automatic image processing and analysis algorithm is developed as part of a complete on-line web characterization system of a papermaking process at the wet end. The goal is to: (1) link certain types of structures on the surface of the web to known machine parameter values, and (2) find the connection between detected structures at the beginning of the line and defects seen on the final product. Images of the pulp mixture (slurry), carried by a fast moving table, are obtained using a stroboscopic light and a CCD camera. This characterization algorithm succeeded where conventional contrast and edge detection techniques failed due to a poorly controlled environment. The images obtained have poor contrast and contain noise caused by a variety of sources. After a number of enhancement steps, conventional segmentation methods still f ailed to detect any structures and are consequently discarded. Techniques tried include the Canny edge detector, the Sobel, Roberts, and Prewitt's filters, as well as zero crossings. The facet model algorithm, is then applied to the images with various parameter settings and is found to be successful in detecting the various topographic characteristics of the surface of the slurry. Pertinent topographic elements are retained and a filtered image computed. Carefully tailored morphological operators are then applied to detect and segment regions of interest. Those regions are then selected according to their size, elongation, and orientation. Their bounding rectangles are computed and represented. Also addressed in this paper are aspects of the real time implementation of this algorithm for on-line use. The algorithm is tested on over 500 images of slurry and is found to segment and characterize nonuniformities on all 500 images.

  19. Surface-spin magnetism of antiferromagnetic NiO in nanoparticle and bulk morphology

    International Nuclear Information System (INIS)

    Jagodic, M; Jaglicic, Z; Jelen, A; Dolinsek, J; Lee, Jin Bae; Kim, Hae Jin; Kim, Young-Min

    2009-01-01

    The surface-spin magnetism of the antiferromagnetic (AFM) material NiO in nanoparticle and bulk morphology was investigated by magnetic measurements (temperature-dependent zero-field-cooled (zfc) and field-cooled (fc) dc susceptibility, ac susceptibility and zfc and fc hysteresis loops). We addressed the question of whether the multisublattice ordering of the uncompensated surface spins and the exchange bias (EB) effect are only present in the nanoparticles, originating from their high surface-to-volume ratio or if these surface phenomena are generally present in the AFM materials regardless of their bulky or nanoparticle morphology, but the effect is just too small to be detected experimentally in the bulk due to a very small surface magnetization. Performing experiments on the NiO nanoparticles of different sizes and bulk NiO grains, we show that coercivity enhancement and hysteresis loop shift in the fc experiments, considered to be the key experimental manifestations of multisublattice ordering and the EB effect, are true nanoscale phenomena only present in the nanoparticles and absent in the bulk.

  20. Effects of decontamination solutions on the surface of titanium: investigation of surface morphology, composition, and roughness.

    Science.gov (United States)

    Wheelis, Sutton E; Gindri, Izabelle M; Valderrama, Pilar; Wilson, Thomas G; Huang, Jessica; Rodrigues, Danieli C

    2016-03-01

    To investigate the impact of treatments used to detoxify dental implants on the oxide layer morphology and to infer how changes in morphology created by these treatments may impact re-osseointegration of an implant. Pure titanium (cpTi) and the alloy Ti6Al4V were subjected to a series of chemical treatments and mechanical abrasion simulating surface decontamination of dental implants. The morphology and roughness of the surface layer before and after treatment with these solutions were investigated with optical and atomic force microscopy (OM, AFM). The solutions employed are typically used for detoxification of dental implants. These included citric acid, 15% hydrogen peroxide, chlorhexidine gluconate, tetracycline, doxycycline, sodium fluoride, peroxyacetic acid, and treatment with carbon dioxide laser. The treatments consisted of both immersions of samples in solution and rubbing with cotton swabs soaked in solution for 1, 2, and 5 min. Cotton swabs used were analyzed with energy dispersive spectroscopy (EDS). The microscopy investigation showed that corrosion and pitting of the samples were present in both metal grades with immersion and rubbing methods when employing more acidic solutions, which had pH acidic solutions caused surface discoloration when coupled with rubbing but did not cause corrosion with immersion. Neutral or basic treatments resulted in no signs of corrosion with both methods. EDS results revealed the presence of titanium particles on all rubbing samples. It was demonstrated in this study that acidic environments coupled with rubbing are able to introduce noticeable morphological changes and corrosion on the surface of both titanium grades. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  1. Morphological characteristics of primary enamel surfaces versus permanent enamel surfaces: SEM digital analysis.

    Science.gov (United States)

    Lucchese, A; Storti, E

    2011-09-01

    The morphology of permanent and primary enamel surface merits further analysis. The objective of this study was to illustrate a method of SEM digital image processing able to quantify and discriminate between the morphological characteristics of primary and permanent tooth enamel. Sixteen extracted teeth, 8 primary teeth and 8 permanent teeth, kept in saline solution, were analysed. The teeth were observed under SEM. The SEM images were analysed by means of digitally processed algorithms. The two algorithms used were: Local standard deviation to measure surface roughness with the roughness index (RI); Hough's theorem to identify linear structures with the linear structure index (LSI). The SEM images of primary teeth enamel show smooth enamel with little areas of irregularity. No linear structures are apparent. The SEM images of permanent enamel show a not perfectly smooth surface; there are furrows and irregularities of variable depth and width. In the clinical practice a number of different situations require the removal of a thin layer of enamel. Only a good morphological knowledge of both permanent and primary tooth enamel gives the opportunity to identify and exploit the effects of rotary tools on enamel, thus allowing for a correct finishing technique.

  2. Effects of methamphetamine dependence and HIV infection on cerebral morphology

    DEFF Research Database (Denmark)

    Jernigan, Terry Lynne; Gamst, Abthony C; Archibald, Sarah L.

    2005-01-01

    - and education-matched comparison groups were analyzed. Main effects of age, HIV infection, methamphetamine dependence, and the interactions of these factors were examined in analyses of cerebral gray matter structure volumes. RESULTS: Independent of the effect of age, HIV infection was associated with reduced...... volumes of cortical, limbic, and striatal structures. There was also some evidence of an interaction between age and HIV infection such that older HIV-positive participants suffered disproportionate loss. Methamphetamine dependence was surprisingly associated with basal ganglia and parietal cortex volume...... increases, and in one of these structures-the nucleus accumbens-there appeared to be a larger effect in younger methamphetamine abusers. Neurocognitive impairment was associated with decreased cortical volumes in HIV-positive participants but with increased cortical volumes in methamphetamine...

  3. Effect of various tooth whitening modalities on microhardness, surface roughness and surface morphology of the enamel.

    Science.gov (United States)

    Kwon, So Ran; Kurti, Steven R; Oyoyo, Udochukwu; Li, Yiming

    2015-09-01

    The purpose of this study was to evaluate the effect of four whitening modalities on surface enamel as assessed with microhardness tester, profilometer, and scanning electron microscopy (SEM). Whitening was performed according to manufacturer's directions for over-the-counter (OTC), dentist dispensed for home use (HW) and in-office (OW) whitening. Do-it-yourself (DIY) whitening consisted of a strawberry and baking soda mix. Additionally, negative and positive controls were used. A total of 120 enamel specimens were used for microhardness testing at baseline and post-whitening. Following microhardness testing specimens were prepared for SEM observations. A total of 120 enamel specimens were used for surface roughness testing at baseline and post-whitening (n = 20 per group). Rank-based Analysis of Covariance was performed to compare microhardness and surface roughness changes. Tests of hypotheses were two-sided with α = 0.05. There was a significant difference in Knoop hardness changes (ΔKHN) among the groups (Kruskal-Wallis test, p < 0.0001). Significant hardness reduction was observed in the positive control and DIY group (p < 0.0001). Mean surface roughness changes (ΔRa) were significantly different among the groups (Kruskal-Wallis test, p < 0.0001). Surface roughness increased in the OTC group (p = 0.03) and in the positive control (p < 0.0001). The four whitening modalities-DIY, OTC, HW and OW induced minimal surface morphology changes when observed with SEM. It can be concluded that none of the four whitening modalities adversely affected enamel surface morphology. However, caution should be advised when using a DIY regimen as it may affect enamel microhardness and an OTC product as it has the potential to increase surface roughness.

  4. Morphological Dependence of Element Stoichiometry in the H. americanus Exoskeleton

    Science.gov (United States)

    Mergelsberg, S. T.; Ulrich, R. N.; Dove, P. M.

    2016-02-01

    The crustacean exoskeleton is a complex biocomposite of inorganic mineral and organic macromolecules that expresses highly divergent morphologies across different taxa. While the structures and compositions of the organic framework show complex links to environmental and developmental pressures, little is known about the mineral chemistry. Previous studies of the cuticle have assumed that magnesium, phosphorous, and other trace metals are largely contained in the inorganic mineral fraction. Due to analytical limitations of structural analyses and in situ spectroscopic methods, the stoichiometry of the organic and inorganic portions could not be resolved. For example, previous Raman and XRD studies conclude the higher concentrations of trace elements, such as P and Mg measured in reinforced structures, e.g. the claw and abdomen, are primarily determined by the mineral fraction. Using the American Lobster (Homarus americanus) as a model organism to establish relationships between body part function and cuticle composition, this study quantified the distributions of Mg and P in the mineral and organic fractions. The experiments were designed to dissolve the exoskeleton of 10 body parts using three types of solutions that were specific to extracting 1) the mineral phase, 2) protein, and 3) polysaccharide. Analysis of the solutions by ICP-OES shows the mineral phase contains magnesium and phosphorous at concentrations sufficient to support the formation of calcium-magnesium and phosphate minerals. The protein fraction of the body parts contains significantly more Mg and P than previously hypothesized, while the levels of P contained in the organic portion are fairly constant. The findings demonstrate the lobster cuticle contains a significant amount of non-mineralized P and Mg that is readily water-soluble in the protein component. However, for those body parts used for defense and food acquisition, such as the claw, the mineral component determines the overall

  5. Quantitative characterization of the influence of the nanoscale morphology of nanostructured surfaces on bacterial adhesion and biofilm formation.

    Directory of Open Access Journals (Sweden)

    Ajay Vikram Singh

    Full Text Available Bacterial infection of implants and prosthetic devices is one of the most common causes of implant failure. The nanostructured surface of biocompatible materials strongly influences the adhesion and proliferation of mammalian cells on solid substrates. The observation of this phenomenon has led to an increased effort to develop new strategies to prevent bacterial adhesion and biofilm formation, primarily through nanoengineering the topology of the materials used in implantable devices. While several studies have demonstrated the influence of nanoscale surface morphology on prokaryotic cell attachment, none have provided a quantitative understanding of this phenomenon. Using supersonic cluster beam deposition, we produced nanostructured titania thin films with controlled and reproducible nanoscale morphology respectively. We characterized the surface morphology; composition and wettability by means of atomic force microscopy, X-ray photoemission spectroscopy and contact angle measurements. We studied how protein adsorption is influenced by the physico-chemical surface parameters. Lastly, we characterized Escherichia coli and Staphylococcus aureus adhesion on nanostructured titania surfaces. Our results show that the increase in surface pore aspect ratio and volume, related to the increase of surface roughness, improves protein adsorption, which in turn downplays bacterial adhesion and biofilm formation. As roughness increases up to about 20 nm, bacterial adhesion and biofilm formation are enhanced; the further increase of roughness causes a significant decrease of bacterial adhesion and inhibits biofilm formation. We interpret the observed trend in bacterial adhesion as the combined effect of passivation and flattening effects induced by morphology-dependent protein adsorption. Our findings demonstrate that bacterial adhesion and biofilm formation on nanostructured titanium oxide surfaces are significantly influenced by nanoscale morphological

  6. Particle morphology dependent superhydrophobicity in treated diatomaceous earth/polystyrene coatings

    Science.gov (United States)

    Sedai, Bhishma R.; Alavi, S. Habib; Harimkar, Sandip P.; McCollum, Mark; Donoghue, Joseph F.; Blum, Frank D.

    2017-09-01

    Superhydrophobic surfaces have been prepared from three different types of diatomaceous earth (DE) particles treated with 3-(heptafluoroisopropoxy)propyltrimethoxysilane (HFIP-TMS) and low molecular mass polystyrene. The untreated particles, consisting of CelTix DE (disk shape), DiaFil DE (rod shape) and EcoFlat DE (irregular), were studied using particle size analysis, bulk density, pore volume and surface area analysis (via Brunauer-Emmett-Teller, BET, methods). The treated particles were characterized with thermogravimetric analysis (TGA), contact angles, scanning electron microscopy, profilometry, and FTIR spectroscopy. The minimum amount of silane coupling agent on the DE surfaces required to obtain superhydrophobicity of the particles was determined and found to be dependent on the particle morphology. In the coatings made from different particles with 2.4 wt% HFIP-TMS, the minimum amounts of treated particles (loadings) for superhydrophobicity was determined with the less dense CelTix DE requiring about 30 wt%, DiaFil DE requiring about 40 wt%, and EcoFlat DE each requiring about 60 wt% loading of treated particles.

  7. Effects of surface morphology on the optical and electrical properties of Schottky diodes of CBD deposited ZnO nanostructures

    Science.gov (United States)

    Mwankemwa, Benard S.; Akinkuade, Shadrach; Maabong, Kelebogile; Nel, Jackie M.; Diale, Mmantsae

    2018-04-01

    We report on effect of surface morphology on the optical and electrical properties of chemical bath deposited Zinc oxide (ZnO) nanostructures. ZnO nanostructures were deposited on the seeded conducting indium doped tin oxide substrate positioned in three different directions in the growth solution. Field emission scanning electron microscopy was used to evaluate the morphological properties of the synthesized nanostructures and revealed that the positioning of the substrate in the growth solution affects the surface morphology of the nanostructures. The optical absorbance, photoluminescence and Raman spectroscopy of the resulting nanostructures are discussed. The electrical characterization of the Schottky diode such as barrier height, ideality factor, rectification ratios, reverse saturation current and series resistance were found to depend on the nanostructures morphology. In addition, current transport mechanism in the higher forward bias of the Schottky diode was studied and space charge limited current was found to be the dominant transport mechanism in all samples.

  8. Dependence of Bacterial Magnetosome Morphology on Chemical Conditions in Deep-sea Sediments

    Science.gov (United States)

    Yamazaki, T.; Suzuki, Y.; Kawamura, N.

    2016-12-01

    Magnetotactic bacteria (MTB) should play an important role for biogeochemical cycles of iron. MTB are considered to be microaerophilic and most commonly live near or below the oxic-anoxic transition zone (OATZ). However, common occurrence of magnetofossils in Pacific red clay (Yamazaki & Shimono, 2013), which contains abundant dissolved oxygen and does not have an OATZ, may conflict with the widespread interpretations of the ecology of MTB. For better understanding of the ecology in deep-sea sediments, we conducted rock-magnetic, biogeochemical, and microbiological analyses of Japan Sea surface sediments with an OATZ. Rock magnetic proxies and TEM images indicate that magnetofossils occur throughout the sediment columns regardless of the OATZ, even at the sediment-water interface. The proportion of magnetofossils with teardrop morphology increases near the OATZ. These suggest that some species producing teardrop magnetosomes prefer a chemical condition near the OATZ, whereas other species may live in microaerophilic microenvironments around organic particles near the sediment-water interface. The fact that morphology of magnetofossils in Pacific red clay is >90% octahedral suggests that even some species of MTB that yield octahedral magnetosomes might be aerotolerant and prefer oxic environments. To strengthen the notion above, pyrosequencing of 16S rRNA gene sequences was conducted for the corresponding sediments. Among diverse bacterial lineages known to produce magnetosomes, 16S rRNA gene sequences phylogenetically affiliated within the lineage of Nitrospirae known to produce teardrop magnetosomes were distributed only around the OATZ, whereas those affiliated within the family Rhodospirillaceae (α-Proteobacteria) and known to produce octahedral magnetosomes were distributed in all investigated Japan Sea sediments regardless of the OATZ. It is strongly suggested that the dependency on the OATZ is different among phylogenetically and morphologically diverse MTB.

  9. Assessment of bracket surface morphology and dimensional change

    Directory of Open Access Journals (Sweden)

    Pillai Devu Radhakrishnan

    2017-01-01

    Full Text Available Objective: The objective of this study was to compare the surface morphology and dimensional stability of the bracket slot at the onset of treatment and after 12 months of intraoral exposure. The study also compared the amount of calcium at the bracket base which indicates enamel loss among the three orthodontic brackets following debonding after 12 months of intraoral exposure. Materials and Methods: The sample consisted of 60 (0.022” MBT canine brackets. They were divided into three groups: self-ligating, ceramic bracket with metal slot, and stainless steel (SS brackets. The slot dimensions, micromorphologic characteristics of as-received and retrieved brackets were measured with a stereomicroscope and scanning electron microscope (SEM, respectively. The amount of calcium at the bracket base which indicates enamel damage was quantified using energy-dispersive X-ray spectrometry (EDX. Results: The results showed statistically significant alterations (P < 0.05 in the right vertical dimension, internal tie wing width (cervical, right and left depth of the slot (Kruskal–Wallis test. Multiple comparison using Mann–Whitney test showed that ceramic brackets underwent (P < 0.05 minimal alterations in the right vertical dimension, internal tie wing width (cervical, right and left depth of the slot (0.01 mm, −0.003 mm, 0.006 mm, −0.002 mm, respectively when compared with the changes seen in SS and self-ligating brackets. SEM analysis revealed an increase in the surface roughness of ceramic with metal slot brackets and self-ligating bracket showed the least irregularity. The presence of calcium was noted on all evaluated brackets under EDX, but ceramic with metal slot brackets showed a significantly greater amount of enamel loss (P = 0.001. Conclusion: Ceramic brackets were found to be dimensionally stable when compared to SS and self-ligating. Self-ligating bracket showed minimal surface irregularity. Ceramic with metal slot brackets showed a

  10. Surface Morphology and Hardness Analysis of TiCN Coated AA7075 Aluminium Alloy

    Science.gov (United States)

    Srinath, M. K.; Ganesha Prasad, M. S.

    2017-12-01

    Successful titanium carbonitride (TiCN) coating on AA7075 plates using the PVD technique depends upon many variables, including temperature, pressure, incident angle and energy of the reactive ions. Coated specimens have shown an increase in their surface hardness of 2.566 GPa. In this work, an attempt to further augment the surface hardness and understand its effects on the surface morphology was performed through heat treatments at 500°C for different duration of times. Specimen's heat treated at 500°C for 1 h exhibited a maximum surface hardness of 6.433 GPa, corresponding to an increase of 92.07%. The XRD results showed the presence of Al2Ti and AlTi3N and indicate the bond created between them. Unit cell lattice parameters in the XRD data are calculated using Bragg's law. The SEM images exhibit increasing crack sizes as the heat treatment time is increased. From the studies, the heat treatment duration can be optimized to 1 h, which exhibited an augmented surface hardness, as further increases in durations caused a drop in the surface hardness. The heat treatment effectively modified the surface hardness. Equations providing the relationships that temperature and time have with the reaction parameters are presented.

  11. Effect of lactic acid on nucleation morphology and surface ...

    Indian Academy of Sciences (India)

    Deposition process started at some initial priority growing centres independently distributed on the substrate. We found that the morphology and ... agent in the bath solution, morphology of initial deposition centres change from coniform ... control the rate of release of free metal ions for the reduction reaction. The chemical ...

  12. Hole mobility in thermally evaporated pentacene: Morphological and directional dependence

    Science.gov (United States)

    Günther, Alrun A.; Widmer, Johannes; Kasemann, Daniel; Leo, Karl

    2015-06-01

    Pentacene has been extensively studied as an active material for organic field-effect transistors as it shows very good charge carrier mobility along its preferred transport direction. In this contribution, we investigate the hole transport in pentacene thin films by measurement in conventional lateral organic field-effect transistors (OFETs), which yields the hole mobility along the a-b plane of pentacene, and by the recently published potential mapping (POEM) approach, which allows for direct extraction of the charge carrier mobility perpendicular to the substrate, in this case perpendicular to the a-b plane, without the assumption of a specific transport model. While the mobility along the a-b plane—determined from OFET measurements—is found to be in the region of 0.45 cm2/Vs, transport perpendicular to this plane shows an average mobility at least one order of magnitude lower. Investigating also how these effective mobility values depend on the deposition rate of the pentacene films, we find that the decrease in grain size for increasing deposition rate causes the mobility to decrease both parallel and perpendicular to the substrate due to the increased number of grain boundaries to be overcome. For the out-of-plane transport, this effect is found to saturate for deposition rates higher than 2.5 Å/s.

  13. Characterization of the Surface Morphology of Bacillus Spores by Atomic Force Microscopy

    National Research Council Canada - National Science Library

    Zolock, Ruth

    2002-01-01

    The surface morphology of Bacillus spores was resolved by atomic force microscopy in order to determine if characteristic surface features could be used to distinguish between closely related species...

  14. Bi-stage time evolution of nano-morphology on inductively coupled plasma etched fused silica surface caused by surface morphological transformation

    Science.gov (United States)

    Jiang, Xiaolong; Zhang, Lijuan; Bai, Yang; Liu, Ying; Liu, Zhengkun; Qiu, Keqiang; Liao, Wei; Zhang, Chuanchao; Yang, Ke; Chen, Jing; Jiang, Yilan; Yuan, Xiaodong

    2017-07-01

    In this work, we experimentally investigate the surface nano-roughness during the inductively coupled plasma etching of fused silica, and discover a novel bi-stage time evolution of surface nano-morphology. At the beginning, the rms roughness, correlation length and nano-mound dimensions increase linearly and rapidly with etching time. At the second stage, the roughening process slows down dramatically. The switch of evolution stage synchronizes with the morphological change from dual-scale roughness comprising long wavelength underlying surface and superimposed nano-mounds to one scale of nano-mounds. A theoretical model based on surface morphological change is proposed. The key idea is that at the beginning, etched surface is dual-scale, and both larger deposition rate of etch inhibitors and better plasma etching resistance at the surface peaks than surface valleys contribute to the roughness development. After surface morphology transforming into one-scale, the difference of plasma resistance between surface peaks and valleys vanishes, thus the roughening process slows down.

  15. Spatial and temporal changes in the morphology of preosteoblastic cells seeded on microstructured tantalum surfaces

    DEFF Research Database (Denmark)

    Justesen, Jørn; Lorentzen, M.; Andersen, L. K.

    2009-01-01

    It has been widely reported that surface morphology on the micrometer scale affects cell function as well as cell shape. In this study, we have systematically compared the influence of 13 topographically micropatterned tantalum surfaces on the temporal development of morphology, including spreadi...

  16. Decalin-assisted light emitting porous Si formation and its optical, surface and morphological properties

    Science.gov (United States)

    Karatutlu, Ali; Istengir, Sumeyra; Cosgun, Sedat; Seker, Isa; Unal, Bayram

    2017-11-01

    In this research paper, light emitting porous silicon (Lep-Si) samples were fabricated by a surfactant-mediated chemical stain etching solution in order to form homogenous luminescent nanostructures at room temperature. As an industrially important solvent, decalin (decahydronaphtalene) was used as a surfactant in the HF/HNO3 solutions in order to control the etching process. Morphological, surface and optical properties of the Lep-Si samples were examined using atomic force microscopy, X-ray photoelectron spectroscopy, photoluminescence (PL) spectroscopy, and laser scanning confocal microscopy (LSCM) techniques. These characterization techniques were correlated with the various etching times including depth dependent luminescence profiles for the first time. We report the optimum conditions for production of the most efficient Lep-Si using decalin (decahydronaphtalene) and possible structural origins of light emission using the depth dependent luminescence measurements.

  17. Effect of surface topography and morphology on space charge packets in polyethylene

    International Nuclear Information System (INIS)

    Zhou Yuanxiang; Wang Yunshan; Sun Qinghua; Wang Ninghua

    2009-01-01

    Polyethylene (PE) is a major kind of internal insulating material. With great progresses of space charge measurement technologies in the last three decades, lots of researches are focused on space charge in PE. The heat pressing and annealing condition of polyethylene affect its morphology obviously. During the heat pressing, the surface of PE forms different surface topographies because of different substrate materials. Surface topography has great relation to the epitaxial crystallization layer and influences the space charge characteristic of PE dramatically. This paper studied the formation process of different surface topographies and their micrographic characters in low density polyethylene (LDPE). pulsed electro-acoustic (PEA) method was used to measure the space charge distribution of samples with different surface topographies and morphologies in LDPE. The effect of surface topography and morphology to space charge packet were studied. The surface topography has great influence on space charge packet polarity and morphology has influence on both movement speed rate and polarity of space charge packet.

  18. The importance of three dimensional dune morphology on the time dependent flow field

    Science.gov (United States)

    Hardy, Richard; Parsons, Dan; Reesink, Arnold; Best, Jim

    2017-04-01

    The flow field over dunes has been extensively studied and there is general understanding of the nature of the flow over dunes formed over two dimensional dunes under equilibrium flow conditions. This model is typically used to explain flow fields over all dunes fields. However, fluvial systems typically experience unsteady flow and therefore the sediment-water interface is constantly reorganizing to form complex three-dimensional morphologies (ripples, dunes and bar forms). Here we investigate how flow over natural three dimensional dunes differs from the accepted model of flow of two dimensional dunes. A series of experiments were undertaken in a flume where fine sand was water worked under a range of unsteady hydraulic conditions to generate quasi-equilibrium three dimensional bed forms. On four occasions, the flume was drained and the bed topography measured with terrestrial LiDAR to create digital elevation models (DEM). Here to demonstrate the approach we choose the DEM with the greatest topographic variation and apply a new Large Eddy Simulation model with an wall-adapting local eddy-viscosity (WALE) turbulence model and a non-linear higher-order numerical differencing scheme. This provided a three dimensional time dependent prediction of the flow field over the static three-dimensional dune morphology at millimeter and hertz scale resolution. The numerically predicted flows were analyzed by standard Reynolds decomposition approaches and Eulerian and Lagrangian coherent flow structure identification methods. The results show that the superimposed bed forms can cause changes in the nature of the classical separated flow regions, in particularly the number of locations where vortices are shed and the points of flow reattachment. Coalescence of vortices generated downstream and can be seen to move to the free surface and form kolk signatures. These structures also correlate in space and time showing a clear flow morphology feedback. The modified flow field

  19. Morphology-dependent activity of Pt nanocatalysts for ethanol oxidation in acidic media: Nanowires versus nanoparticles

    International Nuclear Information System (INIS)

    Zhou Weiping; Li Meng; Koenigsmann, Christopher; Ma Chao; Wong, Stanislaus S.; Adzic, Radoslav R.

    2011-01-01

    Highlights: → We demonstrate the morphology effect of Pt catalysts in electrooxidation of ethanol and CO in an acidic solution. → Pt nanowires and nanoparticles were used as catalysts. → Pt nanowires display a higher catalytic activity by a factor of at least two relative to those nanoparticles for ethanol oxidation. → The rate for CO monolayer oxidation exhibits similar morphology-dependent behavior with a markedly enhanced rate on the Pt nanowires. - Abstract: The morphology of nanostructured Pt catalysts is known to affect significantly the kinetics of various reactions. Herein, we report on a pronounced morphology effect in the electrooxidation of ethanol and carbon monoxide (CO) on Pt nanowires and nanoparticles in an acidic solution. The high resolution transmission electron microscopy analysis showed the inherent morphology difference between these two nanostructured catalysts. Voltammetric and chronoamperometric studies of the ethanol electrooxidation revealed that these nanowires had a higher catalytic activity by a factor of two relative to these nanoparticles. The rate for CO monolayer oxidation exhibits similar morphology-dependent behavior with a markedly enhanced rate on the Pt nanowires. In situ infrared reflection-absorption spectroscopy measurements revealed a different trend for chemisorbed CO formation and CO 2 -to-acetic acid reaction product ratios on these two nanostructures. The morphology-induced change in catalytic activity and selectivity in ethanol electrocatalysis is discussed in detail.

  20. IDENTIFYING THE LOCAL SURFACE URBAN HEAT ISLAND THROUGH THE MORPHOLOGY OF THE LAND SURFACE TEMPERATURE

    Directory of Open Access Journals (Sweden)

    J. Wang

    2016-06-01

    Full Text Available Current characterization of the Land Surface Temperature (LST at city scale insufficiently supports efficient mitigations and adaptations of the Surface Urban Heat Island (SUHI at local scale. This research intends to delineate the LST variation at local scale where mitigations and adaptations are more feasible. At the local scale, the research helps to identify the local SUHI (LSUHI at different levels. The concept complies with the planning and design conventions that urban problems are treated with respect to hierarchies or priorities. Technically, the MODerate-resolution Imaging Spectroradiometer satellite image products are used. The continuous and smooth latent LST is first recovered from the raw images. The Multi-Scale Shape Index (MSSI is then applied to the latent LST to extract morphological indicators. The local scale variation of the LST is quantified by the indicators such that the LSUHI can be identified morphologically. The results are promising. It can potentially be extended to investigate the temporal dynamics of the LST and LSUHI. This research serves to the application of remote sensing, pattern analysis, urban microclimate study, and urban planning at least at 2 levels: (1 it extends the understanding of the SUHI to the local scale, and (2 the characterization at local scale facilitates problem identification and support mitigations and adaptations more efficiently.

  1. Effect of the surface temperature on surface morphology, deuterium retention and erosion of EUROFER steel exposed to low-energy, high-flux deuterium plasma

    Directory of Open Access Journals (Sweden)

    M. Balden

    2017-08-01

    Full Text Available Samples of EUFROFER, a reduced activation ferritic martensitic steel, were exposed in the linear plasma device Pilot-PSI to a deuterium (D plasma with incident ion energy of ∼40eV and incident D flux of 2–6×1023D/m2s to fluences up to 1027D/m2 at surface temperatures ranging from 400K to 950K. The main focus of the study lays on the surface morphology changes dependent on the surface temperature and the surface composition evolution, e.g., the enrichment in tungsten; but also the erosion and the D retention are studied. The created surface morphology varies strongly with surface temperature from needle-like to corral-like structures. The visible lateral length scale of the formed structures is in the range of tens of nanometres to above 1µm and exhibits two thermal activated regimes below and above ∼770K with activation energies of 0.2eV and 1.3eV, respectively. The lateral variation of the enrichment of heavy elements on the surface is correlated to this surface morphology at least in the high temperature regime, independent of the origin of the enrichment (intrinsic from the sample or deposited by the plasma. Also the erosion exhibits temperature dependence at least above ∼770K as well as a fluence dependence. The amount of deuterium retained in the top 500nm is almost independent of the exposure temperature and is of the order of 1018D/m2, which would correspond to a sub-monolayer D coverage on the surface. The retained D in the volume summing up over the complete samples exceeds the D retained close to the surface by one order of magnitude.

  2. Low energy oxygen ion beam modification of the surface morphology and chemical structure of polyurethane fibers

    International Nuclear Information System (INIS)

    Wong, K.H.; Zinke-Allmang, M.; Wan, W.K.; Zhang, J.Z.; Hu, P.

    2006-01-01

    Energetic O + ions were implanted into polyurethane (PU) fiber filaments, at 60 and 100 keV with doses of 5 x 10 14 and 1 x 10 15 ions/cm 2 , to modify the near-surface fiber morphology. The implantations were performed at room temperature and at -197 deg. C, a temperature well below the glass transition temperature for this system. At room temperature, the lower energy implantation heats the fibers primarily near their surface, causing the fiber surface to smoothen and to develop a flattened shape. At the higher energy, the ion beam deposits its energy closer to the fiber core, heating the fiber more uniformly and causing them to re-solidify slowly. This favors a cylindrical equilibrium shape with a smooth fiber surface and no crack lines. The average fiber diameter reduced during 100 keV implantation from 3.1 to 2.3 μm. At -197 deg. C, the ion implantation does not provide enough heat to cause notable physical modifications, but the fibers crack and break during subsequent warming to room temperature. The dose dependence of the crack formation along the fiber intersections is presented. The ion beams further cause near-surface chemical modifications in the fibers, particularly introducing two new chemical functional groups (C-(C=O)-C and C-N-C)

  3. Mechanism of action of pefloxacin on surface morphology, DNA ...

    African Journals Online (AJOL)

    work-group

    2011-11-16

    Nov 16, 2011 ... Department of Life Sciences, Applied Microbiology Laboratory, University of Mumbai, Vidyanagari, Santacruz (E),. Mumbai 400098 ... The MIC determined by broth dilution method and Hi-Comb method was 0.1 µg/ml. Morphological ... against Gram-negative bacteria involved in UTI, the quinolone class has ...

  4. Morphology, surface topography and optical studies on electron ...

    Indian Academy of Sciences (India)

    Home; Journals; Bulletin of Materials Science; Volume 29; Issue 5. Morphology ... Their AFM images exhibit columnar/pyramidal/truncated cone structure, providing support to the 3D Stranski–Krastanov model for film growth. Further, they ... Materials Science Programme, Indian Institute of Technology, Kanpur 208 016, India ...

  5. Influence of multi-wavelength laser irradiation of enamel and dentin surfaces on surface morphology and permeability

    Science.gov (United States)

    Chang, Nai-Yuan N.; Jew, Jamison; Simon, Jacob C.; Chan, Kenneth H.; Lee, Robert C.; Fried, William A.; Cho, Jinny; Darling, Cynthia L.; Fried, Daniel

    2017-02-01

    UV and IR lasers can be used to specifically target protein, water, and the mineral phase of dental hard tissues to produce varying changes in surface morphology. In this study, we irradiated enamel and dentin surfaces with various combinations of lasers operating at 0.355, 2.94, and 9.4 μm, exposed those surfaces to topical fluoride, and subsequently evaluated the influence of these changes on surface morphology and permeability. Digital microscopy and surface dehydration rate measurements were used to monitor changes in the samples overtime. The surface morphology and permeability (dehydration rate) varied markedly with the different laser treatments on enamel. On dentin, fluoride was most effective in reducing the permeability.

  6. Effect of surface diffusion on morphology and scaling properties during glancing angle deposition

    Science.gov (United States)

    Mukherjee, Srijit

    growth front of the nanorods as a function of diffusion length scale which effects the atomic shadowing. Analysis of shadowing by diffusion mediated surface roughness at the growth front of nanorods grown by GLAD indicates that self-shadowing plays an important role in determining the morphology of the layer. The growth exponent p is dependent on the nature of geometric shadowing interactions between the rods as well as due to self-inflicted shadowing by the islands at the growth fronts on the rods themselves. I propose an analytical model based on mean-field nucleation theory and non-linear chaos theory which predicts a linear dependence of p on the average island separation or the diffusion length scale of the adatoms on the growth front. The model explains the occurrence of anomalous scaling at 0.24 ≤ theta ≤ 0.34 with of a transition from 2D to a 3D island growth mechanism. A fit based on the model predicts a critical homologous deposition temperature thetac of 0.24 +/- 0.02 for all metallic systems (Al, Cr, Nb and Ta) under consideration.

  7. Disruption of the NADPH-dependent glutamate dehydrogenase affects the morphology of two industrial strains of Penicillium chrysogenum

    DEFF Research Database (Denmark)

    Thykær, Jette; Kildegaard, Kanchana Rueksomtawin; Noorman, H.

    2009-01-01

    New morphological aspects of Penicillium chrysogenum were found during physiological characterisation of two NADPH-dependent glutamate dehydrogenase mutant strains. A morphological characterisation of the previously constructed strains, together with the two beta-lactam producing industrial recip...

  8. Modeling three-dimensional surface morphology of biocake layer in a membrane bioreactor based on fractal geometry.

    Science.gov (United States)

    Zhao, Leihong; Yang, Lining; Lin, Hongjun; Zhang, Meijia; Yu, Haiying; Liao, Bao-Qiang; Wang, Fangyuan; Zhou, Xiaoling; Li, Renjie

    2016-12-01

    While the adsorptive fouling in membrane bioreactors (MBRs) is highly dependent of the surface morphology, little progress has been made on modeling biocake layer surface morphology. In this study, a novel method, which combined static light scattering method for fractal dimension (D f ) measurement with fractal method represented by the modified two-variable Weierstrass-Mandelbrot function, was proposed to model biocake layer surface in a MBR. Characterization by atomic force microscopy showed that the biocake surface was stochastic, disorder, self-similarity, and with non-integer dimension, illustrating obvious fractal features. Fractal dimension (D f ) of sludge suspension experienced a significant change with operation of the MBR. The constructed biocake layer surface by the proposed method was quite close to the real surface, showing the feasibility of the proposed method. It was found that D f was the critical factor affecting surface morphology, while other factors exerted moderate or minor effects on the roughness of biocake layer. Copyright © 2016 Elsevier Ltd. All rights reserved.

  9. Manipulating poly(lactic acid) surface morphology by solvent-induced crystallization

    Science.gov (United States)

    Gao, Jian; Duan, Lingyan; Yang, Guanghui; Zhang, Qin; Yang, Mingbo; Fu, Qiang

    2012-11-01

    Here, we report some unique crystalline morphologies of poly(lactic acid) (PLA) via organic solvent-induced crystallization. It was revealed that the surface morphology of PLA can be fine tuned by simply varying the volume ratio of a mixed solvent (acetone/ethanol). By increasing the ethanol content in the mixed solvent, we observed a morphological evolution of PLA surface from spherulite to shish-kebab and bamboo-cage-like structure. It was also interesting to find that the initial surface structure of PLA plays an important role to determine the final solvent-induced crystalline morphology. This work provides a new method for manipulating PLA crystal morphology through a simple solvent-induced crystallization.

  10. Effects of aluminium surface morphology and chemical modification on wettability

    DEFF Research Database (Denmark)

    Rahimi, Maral; Fojan, Peter; Gurevich, Leonid

    2014-01-01

    of a monolayer of fluorinated silane, and a combination of those. The effect of these surface modification techniques on roughness and wettability of the aluminium surfaces was elucidated by ellipsometry, contact angle measurements and atomic force microscopy. We demonstrated that by employing different types...... of surface modifications the contact angle of water droplets on aluminium samples can be varied from 12° to more than 120°. A crossover from Cassie–Baxter to Wenzel regime upon changing the surface roughness was also observed....

  11. High-surface-area silica nanospheres (KCC-1) with a fibrous morphology

    KAUST Repository

    Polshettiwar, Vivek

    2010-08-02

    Fibrous nanosilica: A new family of high-surface-area silica nanospheres (KCC-1) have been prepared (see picture). KCC-1 features excellent physical properties, including high surface area, unprecedented fibrous surface morphology, high thermal (up to 950 °C) and hydrothermal stabilities, and high mechanical stability. Copyright © 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  12. Ion-beam modifications of the surface morphology and conductivity ...

    Indian Academy of Sciences (India)

    Unknown

    Abstract. Studies on the surface micromorphology and surface conductivity in thin polymer films of poly vinyl alcohol (PVA) and poly ethylene oxide (PEO) in both as-grown and ion-implanted polymer films have been carried out to reveal certain specific features of the ordered state in these materials. Optical microscopic.

  13. Effect of surface morphology on atmospheric corrosion behaviour of ...

    Indian Academy of Sciences (India)

    Co18Si1B14 ribbon, was evaluated. The wheel side surface of the ribbon was more corroded than the air side surface, due to the higher density of air pockets present. The phases present in atmospheric rust were analysed by X-ray diffraction ...

  14. Ion-beam modifications of the surface morphology and conductivity ...

    Indian Academy of Sciences (India)

    Studies on the surface micromorphology and surface conductivity in thin polymer films of poly vinyl alcohol (PVA) and poly ethylene oxide (PEO) in both as-grown and ion-implanted polymer films have been carried out to reveal certain specific features of the ordered state in these materials. Optical microscopic ...

  15. The role of surface morphology in nanocatalyst engineering

    Energy Technology Data Exchange (ETDEWEB)

    Stamenkovic, V. [Argonne National Laboratory, Argonne, IL (United States). Material Science Div.

    2008-07-01

    This study investigated extended polycrystalline platinum (Pt) alloys and PtNi(hkl) and Pt(hkl) single crystalline surfaces for various catalytic reactions. The surfaces were treated in an ultra-high vacuum by sputtering and annealing cycles. Auger electron spectroscopy (AES), low energy ion spectroscopy (LEIS), and ultraviolet photoelectron spectroscopy (UPS) techniques were used to characterize the alloys before they were transferred into an electrochemical environment. The study showed that electronic effect was caused by changes in the metallic d-band centre position. Structural effects were caused by surface roughening. The sputtered surfaces formed a Pt-skeleton on the outermost layers as a result of the dissolution of transition metal atoms. A modification of Pt electronic properties altered the adsorption and catalytic properties of the corresponding bimetallic alloy. The most active systems for the oxygen reduction reaction (ORR) were observed in the Pt-skin near-surface formation. 3 refs.

  16. Time-kill profiles and cell-surface morphological effects of crude ...

    African Journals Online (AJOL)

    MK1201 mycelial extract on the viability and cell surface morphology of methicillin-susceptible Staphylococcus aureus (MSSA) and methicillin-resistant Staphylococcus aureus (MRSA). Methods: Time-kill assays were conducted by incubating test ...

  17. Influence of impurities on the surface morphology of the TIBr crystal semiconductor

    International Nuclear Information System (INIS)

    Santos, Robinson A. dos; Silva, Julio B. Rodrigues da; Martins, Joao F.T.; Ferraz, Caue de M.; Costa, Fabio E. da; Mesquita, Carlos H. de; Hamada, Margarida M.; Gennari, Roseli F.

    2013-01-01

    The impurity effect in the surface morphology quality of TlBr crystals was evaluated, aiming a future application of these crystals as room temperature radiation semiconductor detectors. The crystals were purified and grown by the Repeated Bridgman technique. Systematic measurements were carried out for determining the stoichiometry, structure orientation, surface morphology and impurity of the crystal. A significant difference in the crystals impurity concentration was observed for almost all impurities, compared to those found in the raw material. The crystals wafer grown twice showed a surface roughness and grains which may be due to the presence of impurities on the surface, while those obtained with crystals grown three times presented a more uniform surface: even though, a smaller roughness was still observed. It was demonstrated that the impurities affect strongly the surface morphology quality of crystals. (author)

  18. Surface roughness and morphology of three nanocomposites after two different polishing treatments by a multitechnique approach.

    Science.gov (United States)

    Janus, J; Fauxpoint, G; Arntz, Y; Pelletier, H; Etienne, O

    2010-05-01

    The purpose of this study was to assess the surface roughness and morphology of three nanocomposites polished with two different polishing systems. Specimens made of hybrid composite (Tetric Ceram [TC] as control) and nanocomposites: nanofilled (Filtek Supreme [FS]), nanofilled hybrid (Grandio [Gr]), complex nanofilled hybrid (Synergy D6 [Syn]) were polished with CompoSystem [CS] or Sof-Lex [SL] polishing discs. The average surface roughness (Ra) before and after polishing was measured using optical profilometry. Both AFM and SEM techniques were additionally used to analyze the surface morphology after polishing with the aim of relating the surface morphology and the surface roughness. Statistical analysis was done by ANOVA using a general linear model (alpha=0.05) with an adjustment for multiple comparisons. Within the same polishing system, FS exhibited the smoothest surface, followed by Syn, TC and Gr (p<0.0001). Sof-Lex polishing discs produced the smoothest surface compared to CompoSystem (p<0.0001). AFM and SEM observations confirmed that the surface roughness was related to the surface morphology and to the average filler size. Positive correlation between the average filler size and the surface roughness suggest that using nanoparticles in the formulation does not necessary improve the surface texture. The nanofilled composite FS, which contains only nanofillers, showed the best results when associated to Sof-Lex polishing discs. 2010 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  19. Morphology of ɛ-caprolactam crystals dependent on the crystallization conditions

    Science.gov (United States)

    Jansens, P. J.; Langen, Y. H. M.; van den Berg, E. P. G.; Geertman, R. M.

    1995-10-01

    The morphology of caprolactam crystals is an important property because it can affect their filterability. This study shows that the morphology of caprolactam crystals depends on the water content of the mother liquor and on the applied growth kinetics. Needle-like crystals were formed during single crystal experiments under two sets of conditions: (1) at high growth rates in a water rich mother liquor and (2) at low growth rates in the absence of water. Experiments were also performed in a lab-scale batch crystallizer and in a pilot-scale continuous crystallizer but did not yield exclusively needle-like crystals.

  20. Familial Risk for Alcohol Dependence and Brain Morphology: The Role of Cortical Thickness Across the Lifespan.

    Science.gov (United States)

    Hill, Shirley Y

    2018-03-12

    Henderson and colleagues have provided new data from a large cohort demonstrating that cortical thickness, as one index of brain morphology, differs between adolescents with and without a family history of alcohol dependence. Understanding the relationship between brain structure and cognitive ability that differ in those with a family history of alcohol use disorders and those without relatives with AUD may provide clues about the biological substrate of addiction. To date, most of the studies concerning brain morphological differences by familial risk have focused on volumetric differences. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

  1. Formation of biocompatible surface layers depending on the sputtering distance

    Science.gov (United States)

    Nasakina, E. O.; Seregin, A. V.; Baikin, A. S.; Kaplan, M. A.; Konushkin, S. V.; Sergiyenko, K. V.; Kovaleva, E. D.; Kolmakova, A. A.; Leonov, A. V.; Sevost'yanov, M. A.; Kolmakov, A. G.; Simakov, S. V.

    2017-05-01

    Nano- and micro-dimensional surface layers of silver and tantalum on flat and wire NiTi substrates by the method of magnetron sputtering in vacuum were produced. The structure and composition of the samples were determined using SEM and Auger spectroscopy. With an increase in the sputtering distance, the thickness of the surface layers decreases, and the thickness of the transition layer and the dependence of the thickness change as a whole depend on the nature of the sputtered substance.

  2. Self-Healing Thermal Annealing: Surface Morphological Restructuring Control of GaN Nanorods

    Energy Technology Data Exchange (ETDEWEB)

    Conroy, Michele; Li, Haoning; Zubialevich, Vitaly Z.; Kusch, Gunnar; Schmidt, Michael; Collins, Timothy; Glynn, Colm; Martin, Robert W.; O’Dwyer, Colm; Morris, Michael D.; Holmes, Justin D.; Parbrook, Peter J.

    2016-12-07

    With advances in nanolithography and dry etching, top-down methods of nanostructuring have become a widely used tool for improving the efficiency of optoelectronics. These nano dimensions can offer various benefits to the device performance in terms of light extraction and efficiency, but often at the expense of emission color quality. Broadening of the target emission peak and unwanted yellow luminescence are characteristic defect-related effects due to the ion beam etching damage, particularly for III–N based materials. In this article we focus on GaN based nanorods, showing that through thermal annealing the surface roughness and deformities of the crystal structure can be “self-healed”. Correlative electron microscopy and atomic force microscopy show the change from spherical nanorods to faceted hexagonal structures, revealing the temperature-dependent surface morphology faceting evolution. The faceted nanorods were shown to be strain- and defect-free by cathodoluminescence hyperspectral imaging, micro-Raman, and transmission electron microscopy (TEM). In-situ TEM thermal annealing experiments allowed for real time observation of dislocation movements and surface restructuring observed in ex-situ annealing TEM sampling. This thermal annealing investigation gives new insight into the redistribution path of GaN material and dislocation movement post growth, allowing for improved understanding and in turn advances in optoelectronic device processing of compound semiconductors.

  3. Segregation and morphology on the surface of ferritic stainless steel (0 0 1)

    International Nuclear Information System (INIS)

    Fujiyoshi, H.; Matsui, T.; Yuhara, J.

    2012-01-01

    The temperature dependence of the segregation and morphology of ferritic steel (0 0 1) surfaces has been examined by a combination of Auger electron spectroscopy, low-energy electron diffraction (LEED), scanning tunneling microscopy (STM), and low-energy electron loss spectroscopy. Upon annealing ferritic steel at 500 °C, the topmost layer was observed to be mainly composed of Fe-Cr alloy. Oxygen segregation was also detected locally in the STM images. LEED showed a (1 × 1) pattern and a weak (√5 × √5)R27° reconstruction corresponding to Fe and Cr 4 O 5 , respectively. Upon annealing at 600 °C, carbon and chromium co-segregated to the surface, forming two different regions composed of CrC and Cr-based steel, while the Cr 4 O 5 domains disappeared. Upon annealing at 700 °C, nitrogen segregated to the surface, and the topmost layer was observed to be mainly composed of CrN domains with local CrC domains.

  4. Surface chemistry and morphology in single particle optical imaging

    Science.gov (United States)

    Ekiz-Kanik, Fulya; Sevenler, Derin Deniz; Ünlü, Neşe Lortlar; Chiari, Marcella; Ünlü, M. Selim

    2017-05-01

    Biological nanoparticles such as viruses and exosomes are important biomarkers for a range of medical conditions, from infectious diseases to cancer. Biological sensors that detect whole viruses and exosomes with high specificity, yet without additional labeling, are promising because they reduce the complexity of sample preparation and may improve measurement quality by retaining information about nanoscale physical structure of the bio-nanoparticle (BNP). Towards this end, a variety of BNP biosensor technologies have been developed, several of which are capable of enumerating the precise number of detected viruses or exosomes and analyzing physical properties of each individual particle. Optical imaging techniques are promising candidates among broad range of label-free nanoparticle detectors. These imaging BNP sensors detect the binding of single nanoparticles on a flat surface functionalized with a specific capture molecule or an array of multiplexed capture probes. The functionalization step confers all molecular specificity for the sensor's target but can introduce an unforeseen problem; a rough and inhomogeneous surface coating can be a source of noise, as these sensors detect small local changes in optical refractive index. In this paper, we review several optical technologies for label-free BNP detectors with a focus on imaging systems. We compare the surface-imaging methods including dark-field, surface plasmon resonance imaging and interference reflectance imaging. We discuss the importance of ensuring consistently uniform and smooth surface coatings of capture molecules for these types of biosensors and finally summarize several methods that have been developed towards addressing this challenge.

  5. Surfactant assisted surface morphology and thermal properties of polythiophene composites

    Science.gov (United States)

    Vijeth, H.; Niranjana, M.; Yesappa, L.; Chapi, Sharanappa; Raghu, S.; Ashokkumar, S. P.; Devendrappa, H.

    2017-06-01

    Conducting polythiophene (PTH)/aluminium oxide (Al2O3) composites was prepared with camphor sulphonic acid (CSA) as s anionic surfactant by means of in situ chemical oxidation polymerization. The morphology and material phase of PTH/Al2O3 (PTHA) composites were investigated by Field-Emission Scanning Electron Microscopy (FESEM) and Energy-dispersive X-ray spectroscopy (EDX). The FESEM image shows alter the size of grain and EDX results consistent with the presence of Al2O3 and CSA chemical composition. Thermal stability of composites was characterized using TGA/DSC, the results indicate that the PTP/Al2O3 composites have higher thermal stability than that of PTP and decompose at higher temperatures due to addition of anionic surfactant.

  6. Oxygen reduction reaction over silver particles with various morphologies and surface chemical states

    Science.gov (United States)

    Ohyama, Junya; Okata, Yui; Watabe, Noriyuki; Katagiri, Makoto; Nakamura, Ayaka; Arikawa, Hidekazu; Shimizu, Ken-ichi; Takeguchi, Tatsuya; Ueda, Wataru; Satsuma, Atsushi

    2014-01-01

    The oxygen reduction reaction (ORR) in an alkaline solution was carried out using Ag powders having various particle morphologies and surface chemical states (Size: ca. 40-110 nm in crystalline size. Shape: spherical, worm like, and angular. Surface: smooth with easily reduced AgOx, defective with AgOx, and Ag2CO3 surface layer). The various Ag powders were well characterized by X-ray diffraction, X-ray photoelectron spectroscopy, N2 adsorption, scanning electron microscopy, Raman spectroscopy, cyclic voltammetry, and stripping voltammetry of underpotential-deposited lead. Defective and oxidized surfaces enhanced the Ag active surface area during the ORR. The ORR activity was affected by the morphology and surface chemical state: Ag particles with defective and angular surfaces showed smaller electron exchange number between three and four but showed higher specific activity compared to Ag particles with smooth surfaces.

  7. Effects of hydrogen peroxide bleaching strip gels on dental restorative materials in vitro: surface microhardness and surface morphology.

    Science.gov (United States)

    Duschner, Heinz; Götz, Hermann; White, Donald J; Kozak, Kathleen M; Zoladz, James R

    2004-01-01

    This study examined the effects of peroxide tooth bleaching, including Crest Whitestrips hydrogen peroxide gel treatments, on the surface hardness and morphology of common dental restorative treatments. American Dental Association (ADA) recommended dental restorative materials, including amalgam, dental gold, porcelain, glass ionomer, and composites, were prepared according to manufacturers' instructions. A cycling treatment methodology was employed which alternated ex vivo human salivary exposures with bleaching treatments under conditions of controlled temperature and durations of treatment. Bleaching treatments included commercial Crest Whitestrips bleaching gels, which utilize hydrogen peroxide as the in situ bleaching source, and several commercial carbamide peroxide bleaching gels. Control treatments included placebo gels and an untreated group. Crest Whitestrips bleaching included treatment exposures simulating recommended clinical exposures (14 hours), along with excess bleaching simulating exposure to five times suggested Crest Whitestrips use. At the conclusion of treatments, surface microhardness measures and surface morphological assessments with standard and variable pressure (VP-) SEMs were conducted to assess the effects of bleaching exposure on the surface morphology and structural integrity of the restoratives. Surface microhardness and SEM measures revealed no significant deleterious effects on the restoration surfaces from Whitestrips gels. These results confirm that tooth bleaching from the selected commercial hydrogen peroxide or carbamide peroxide bleaching systems does not produce changes in surface morphology or microhardness of common dental restorative materials. These results support the clinical safety of the selected commercial bleaching systems to the oral environment, matching results obtained from long-term use of these ingredients applied in dental offices and available in commercial formulations.

  8. Effect of surface morphology on atmospheric corrosion behaviour of ...

    Indian Academy of Sciences (India)

    Wintec

    adverse effect of quenched-in defects on the corrosion resistance of Fe34Ni36Cr10P14B6 amorphous alloy has been reported by some investigators (Gravano et al 1992). The inferior corrosion resistance of the wheel side surface has been attributed to higher concentration of quenched- in defects due to higher cooling rate ...

  9. Mechanism of action of pefloxacin on surface morphology, DNA ...

    African Journals Online (AJOL)

    It was observed that the site of pefloxacin action was intracellular and it caused surface alterations. The present investigation also showed the effect of Quinolone pefloxacin on DNA gyrase activity of K. aerogenes. DNA gyrase was purified by affinity chromatography and inhibition of pefloxacin on supercoiling activity of DNA ...

  10. Tailoring of morphology and surface properties of syndiotactic polystyrene aerogels.

    Science.gov (United States)

    Wang, Xiao; Jana, Sadhan C

    2013-05-07

    This study evaluates a method for rendering syndiotactic polystyrene (sPS) aerogels hydrophilic using polyethylene oxide (PEO) of different molecular weights. The highly porous sPS aerogels are inherently hydrophobic although applications involving absorption of moisture and removal of particulate solids may benefit from the high surface area of sPS aerogels provided some degree of hydrophilicity is induced in these materials. In this work, sPS gels are prepared by thermo-reversible gelation in tetrahydrofuran in the presence of PEO. The gels are dried under supercritical conditions to obtain aerogels. The aerogels are characterized by scanning electron microscopy, nitrogen-adsorption porosimetry, helium pycnometry, and contact angle measurements. The data reveal that the pore structures and surface energy can be controlled by varying the concentration and molecular weight of PEO and using different cooling rates during thermo-reversible gelation. In the first case, sPS aerogels, aerogels containing PEO of a low molecular weight or low concentration show superhydrophobic surface presenting the "lotus effect". In the second case, PEO at a higher concentration or with higher molecular weight forms phase-separated domains yielding new hydrophilic macropores (>10 μm) in the aerogel structures. These macropores contribute to the superhydrophobic surface with the "petal effect". The cooling rate during gelation shows a strong influence on these two cases.

  11. Surface roughness and morphologic changes of zirconia: Effect of ...

    African Journals Online (AJOL)

    10 MPa m1/2), high biocompatibility and natural appearance. ... perpendicularly to the surface at 10 mm distance and was moved in a sweeping fashion by hand during an exposure period of 20 s over the entire area. The energy parameters.

  12. Surface morphology of contact lenses probed with microscopy techniques

    Czech Academy of Sciences Publication Activity Database

    Guryča, Vilém; Hobzová, Radka; Přádný, Martin; Širc, Jakub; Michálek, Jiří

    2007-01-01

    Roč. 30, č. 4 (2007), s. 215-222 ISSN 1367-0484 R&D Projects: GA AV ČR 1QS400500558 Institutional research plan: CEZ:AV0Z40500505 Keywords : atomic force microscopy * scanning electron microscopy * surface roughness Subject RIV: CD - Macromolecular Chemistry

  13. Improvement in surface morphology of GaSb buffer layer by two-step high and low temperature growth

    Science.gov (United States)

    Okumura, Shigekazu; Tomabechi, Shuichi; Suzuki, Ryo; Matsukura, Yusuke; Tsunoda, Koji; Kon, Jun-ichi; Nishino, Hironori

    2017-11-01

    The surface morphology of GaSb was investigated by changing growth conditions such as thermal oxide desorption temperature, growth temperature, and growth step by solid source molecular beam epitaxy. At high temperature growth, the pits caused by the thermal oxide desorption remained in the GaSb buffer layer surface, while the surface was sufficiently flattened. At low temperature growth, the pits disappeared, while the surface was not enough flattened even in the case of step-flow mode growth. Since the pits disappeared at lower growth temperature regardless of the growth mode, this behavior might be explained by the Ga migration length depending on the growth temperature. By applying two-step high/low temperature growth, where both growth steps proceed in step-flow mode, flat, a pit-free GaSb buffer surface could be obtained.

  14. Shape-dependent Surface Energetics of Nanocrystalline TiO2

    Energy Technology Data Exchange (ETDEWEB)

    Park, T.J.; Wong, S.; Levchenko, A.A.; Zhou, H.; Navrotsky, A.

    2010-10-21

    We report the direct determination of surface enthalpies for nanophase TiO{sub 2} anatase with different morphologies derived from drop solution calorimetry in a molten sodium molybdate (3Na{sub 2}Ol{center_dot}4MoO{sub 3}) solvent at 702 C. The energetics of surface hydration has been measured using a Calvet microcalorimeter coupled with a gas dosing system. The surface enthalpies of hydrated surfaces for anatase TiO{sub 2} nanoparticles, nanowires and sea-urchin-like assemblies are 0.51 {+-} 0.05, 1.07 {+-} 0.28, and 1.29 {+-} 0.16 J m{sup -2}, respectively, whereas those of anhydrous surfaces are 0.74 {+-} 0.04, 1.24 {+-} 0.28, and 1.41 {+-} 0.16 J m{sup -2}, respectively. The trend in TiO{sub 2}, which shows higher surface enthalpies for more complex nanostructures, is consistent with that reported in ZnO. The shape-dependent surface enthalpy at the nanoscale level is discussed in terms of exposed surface structures. The enthalpies of hydration appear to be similar for all morphologies.

  15. Dependence of soot optical properties on particle morphology: measurements and model comparisons.

    Science.gov (United States)

    Radney, James G; You, Rian; Ma, Xiaofei; Conny, Joseph M; Zachariah, Michael R; Hodges, Joseph T; Zangmeister, Christopher D

    2014-03-18

    We report the first mass-specific absorption and extinction cross sections for size- and mass-selected laboratory-generated soot aerosol. Measurement biases associated with aerosols possessing multiple charges were eliminated using mass selection to isolate singly charged particles for a specified electrical mobility diameter. Aerosol absorption and extinction coefficients were measured using photoacoustic and cavity ring-down spectroscopy techniques, respectively, for lacey and compacted soot morphologies. The measurements show that the mass-specific absorption cross sections are proportional to particle mass and independent of morphology, with values between 5.7 and 6 m(2) g(-1). Mass-specific extinction cross sections were morphology dependent and ranged between 12 and 16 m(2) g(-1) for the lacey and compact morphologies, respectively. The resulting single-scattering albedos ranged from 0.5 to 0.6. Results are also compared to theoretical calculations of light absorption and scattering from simulated particle agglomerates. The observed absorption is relatively well modeled, with minimum differences between the calculated and measured mass absorption cross sections ranging from ∼ 5% (lacey soot) to 14% (compact soot). The model, however, was unable to satisfactorily reproduce the measured extinction, underestimating the single-scattering albedo for both particle morphologies. These discrepancies between calculations and measurements underscore the need for validation and refinement of existing models of light scattering and absorption by soot agglomerates.

  16. Inevitable surface dependence of some operator products and integrability

    International Nuclear Information System (INIS)

    Shigemoto, Kazuyasu; Tanaka, Azuma; Taguchi, Yukio; Yamamoto, Kunio.

    1976-01-01

    In general even in local theory the operator products at the same space-time point must be considered as a limit of non-local products. It is natural to confine non-locality on a space-like surface. In this case some operator products with three or more constituents possess an inevitable and purely quantum-mechanical surface dependence. Taking the pion-nucleon system as an example, we explicitly calculate in the order of g 2 this kind of the surface dependence of the interaction Hamiltonian. In order to obtain a consistent theory, this surface is required to be identified with the space-like surface in the Tomonaga-Schwinger equation. Then the interaction Hamiltonian needs an additional, non-canonical and surface-dependent term, which can be derived uniquely from the canonical Hamiltonian. The integrability of the Tomonaga-Schwinger equation is proved by taking account of this surface dependence together with the gradient term in the equal-time commutator. (auth.)

  17. Impact of morphology on diffusive dynamics on curved surfaces.

    Science.gov (United States)

    Kusters, Remy; Storm, Cornelis

    2014-03-01

    Diffusive processes on nonplanar substrates are deeply relevant for cellular function and transport and increasingly used to probe and characterize the behavior of proteins in membranes. We present analytical and numerical analyses of in-plane diffusion of discrete particles on curved geometries reflecting various generic motifs in biology and explore, in particular, the effect that the shape of the substrate has on the characteristic time scales of diffusive processes. To this end, we consider both collective measures (the relaxation of concentration profiles towards equilibrium) and single-particle measures (escape rates and first passage times of individual diffusing molecules): the first relevant for the correct interpretation of FRAP experiments in curved environments; the second, for single-particle tracking probes. Each of these measures is sensitively affected by the morphology of the substrate, and we find that the exit rate out of a domain is not uniquely set by the size of its boundary, illustrating the general principle we reveal: By varying the shape of a substrate, Nature can control the diffusive time scales in a microenvironment without changing the bare substrate properties.

  18. Impact of morphology on diffusive dynamics on curved surfaces

    Science.gov (United States)

    Kusters, Remy; Storm, Cornelis

    2014-03-01

    Diffusive processes on nonplanar substrates are deeply relevant for cellular function and transport and increasingly used to probe and characterize the behavior of proteins in membranes. We present analytical and numerical analyses of in-plane diffusion of discrete particles on curved geometries reflecting various generic motifs in biology and explore, in particular, the effect that the shape of the substrate has on the characteristic time scales of diffusive processes. To this end, we consider both collective measures (the relaxation of concentration profiles towards equilibrium) and single-particle measures (escape rates and first passage times of individual diffusing molecules): the first relevant for the correct interpretation of FRAP experiments in curved environments; the second, for single-particle tracking probes. Each of these measures is sensitively affected by the morphology of the substrate, and we find that the exit rate out of a domain is not uniquely set by the size of its boundary, illustrating the general principle we reveal: By varying the shape of a substrate, Nature can control the diffusive time scales in a microenvironment without changing the bare substrate properties.

  19. Antifreeze Glycoproteins Alter the Molecular Scale Surface Morphology of Ice

    Science.gov (United States)

    Zepeda, Salvador; Orme, Christine A.; Qiu, Roger; Yeh, Yin

    2003-03-01

    Trematomas borchgrevinki live in the harsh super-cooled waters of the Antarctic. Critical to their survival are antifreeze glycoproteins (AFGPs) that further suppress the freezing temperature of their blood serum in addition to the colligative action of salts found in the ocean. These proteins also modify ice crystal growth habits as well as inhibit recrystallization in polycrystalline ice. To date many other types of antifreeze proteins have been identified in cold weather insects, plants, and other fish, but the exact mechanism is not entirely understood. The mechanism is non-colligative since only a few mg/ml are required for ice crystal growth inhibition and a non-equilibrium melting/freezing point hysteresis is observed. Atomic force microscopy (AFM) can yield a wealth of surface information that can reveal molecular scale information of biomineralization processes. We use AFM to directly probe the surface of ice crystals grown from the vapor in the pure phase and in the presence of growth inhibitors/modifiers, AFGPs. Results show that the AFGPs heavily pin the surface of ice.

  20. Simultaneous formation of multiscale hierarchical surface morphologies through sequential wrinkling and folding

    Science.gov (United States)

    Wang, Yu; Sun, Qingyang; Xiao, Jianliang

    2018-02-01

    Highly organized hierarchical surface morphologies possess various intriguing properties that could find important potential applications. In this paper, we demonstrate a facile approach to simultaneously form multiscale hierarchical surface morphologies through sequential wrinkling. This method combines surface wrinkling induced by thermal expansion and mechanical strain on a three-layer structure composed of an aluminum film, a hard Polydimethylsiloxane (PDMS) film, and a soft PDMS substrate. Deposition of the aluminum film on hard PDMS induces biaxial wrinkling due to thermal expansion mismatch, and recovering the prestrain in the soft PDMS substrate leads to wrinkling of the hard PDMS film. In total, three orders of wrinkling patterns form in this process, with wavelength and amplitude spanning 3 orders of magnitude in length scale. By increasing the prestrain in the soft PDMS substrate, a hierarchical wrinkling-folding structure was also obtained. This approach can be easily extended to other thin films for fabrication of multiscale hierarchical surface morphologies with potential applications in different areas.

  1. Effect of Shot Peening in Different Shot Distance and Shot Angle on Surface Morphology, Surface Roughness and Surface Hardness of 316L Biomaterial

    Science.gov (United States)

    Umbu Kondi Maliwemu, Erich; Malau, Viktor; Iswanto, Priyo Tri

    2018-01-01

    Shot peening is a mechanical surface treatment with a beneficial effect to generate compressive residual stress caused by plastic deformation on the surface of material. This plastic deformation can improve the surface characteristics of metallic materials, such as modification of surface morphology, surface roughness, and surface hardness. The objective of this study is to investigate the effect of shot peening in different shot distance and shot angle on surface morphology, surface roughness, and surface hardness of 316L biomaterial. Shot distance was varied at 6, 8, 10, and 12 cm and shot angle at 30, 60, and 90°, working pressure at 7 kg/cm2, shot duration for 20 minutes, and using steel balls S-170 with diameter of 0.6 mm. The results present that the shot distance and shot angle of shot peening give the significant effect to improve the surface morphology, surface roughness, and surface hardness of 316 L biomaterial. Shot peening can increase the surface roughness by the increasing of shot distance and by the decreasing of shot angle. The nearest shot distance (6 cm) and the largest shot angle (90°) give the best results on the grain refinement with the surface roughness of 1.04 μm and surface hardness of 534 kg/mm2.

  2. Adsorption of Xyloglucan onto Cellulose Surfaces of Different Morphologies: An Entropy-Driven Process.

    Science.gov (United States)

    Benselfelt, Tobias; Cranston, Emily D; Ondaral, Sedat; Johansson, Erik; Brumer, Harry; Rutland, Mark W; Wågberg, Lars

    2016-09-12

    The temperature-dependence of xyloglucan (XG) adsorption onto smooth cellulose model films regenerated from N-methylmorpholine N-oxide (NMMO) was investigated using surface plasmon resonance spectroscopy, and it was found that the adsorbed amount increased with increasing temperature. This implies that the adsorption of XG to NMMO-regenerated cellulose is endothermic and supports the hypothesis that the adsorption of XG onto cellulose is an entropy-driven process. We suggest that XG adsorption is mainly driven by the release of water molecules from the highly hydrated cellulose surfaces and from the XG molecules, rather than through hydrogen bonding and van der Waals forces as previously suggested. To test this hypothesis, the adsorption of XG onto cellulose was studied using cellulose films with different morphologies prepared from cellulose nanocrystals (CNC), semicrystalline NMMO-regenerated cellulose, and amorphous cellulose regenerated from lithium chloride/dimethylacetamide. The total amount of high molecular weight xyloglucan (XGHMW) adsorbed was studied by quartz crystal microbalance and reflectometry measurements, and it was found that the adsorption was greatest on the amorphous cellulose followed by the CNC and NMMO-regenerated cellulose films. There was a significant correlation between the cellulose dry film thickness and the adsorbed XG amount, indicating that XG penetrated into the films. There was also a correlation between the swelling of the films and the adsorbed amounts and conformation of XG, which further strengthened the conclusion that the water content and the subsequent release of the water upon adsorption are important components of the adsorption process.

  3. Different methods to alter surface morphology of high aspect ratio structures

    Energy Technology Data Exchange (ETDEWEB)

    Leber, M., E-mail: moritz.leber@utah.edu [Department of Electrical and Computer Engineering, University of Utah, Salt Lake City, UT (United States); Shandhi, M.M.H. [Department of Electrical and Computer Engineering, University of Utah, Salt Lake City, UT (United States); Hogan, A. [Blackrock Microsystems, Salt Lake City, UT (United States); Solzbacher, F. [Department of Electrical and Computer Engineering, University of Utah, Salt Lake City, UT (United States); Bhandari, R.; Negi, S. [Department of Electrical and Computer Engineering, University of Utah, Salt Lake City, UT (United States); Blackrock Microsystems, Salt Lake City, UT (United States)

    2016-03-01

    Graphical abstract: Surface engineering of high aspect ratio silicon structures. - Highlights: • Multiple roughening techniques for high aspect ratio devices were investigated. • Modification of surface morphology of high aspect ratio silicon devices (1:15). • Decrease of 76% in impedance proves significant increase in surface area. - Abstract: In various applications such as neural prostheses or solar cells, there is a need to alter the surface morphology of high aspect ratio structures so that the real surface area is greater than geometrical area. The change in surface morphology enhances the devices functionality. One of the applications of altering the surface morphology is of neural implants such as the Utah electrode array (UEA) that communicate with single neurons by charge injection induced stimulation or by recording electrical neural signals. For high selectivity between single cells of the nervous system, the electrode surface area is required to be as small as possible, while the impedance is required to be as low as possible for good signal to noise ratios (SNR) during neural recording. For stimulation, high charge injection and charge transfer capacities of the electrodes are required, which increase with the electrode surface. Traditionally, researchers have worked with either increasing the roughness of the existing metallization (platinum grey, black) or other materials such as Iridium Oxide and PEDOT. All of these previously investigated methods lead to more complicated metal deposition processes that are difficult to control and often have a critical impact on the mechanical properties of the metal films. Therefore, a modification of the surface underneath the electrode's coating will increase its surface area while maintaining the standard and well controlled metal deposition process. In this work, the surfaces of the silicon micro-needles were engineered by creating a defined microstructure on the electrodes surface using several

  4. Influence of ultrasonic impact treatment and morphology of solid lubricant particles on its attachment to surfaces with different roughness

    Science.gov (United States)

    Fedorov, A. A.; Polonyankin, D. A.; Blesman, A. I.; Postnikov, D. V.; Linovsky, A. V.; Bobkov, N. V.

    2017-08-01

    The article considers the research results of the «friction surface-solid lubricant» system with molybdenum disulfide suspension before the ultrasonic impact treatment. An average particle's size detected in the molybdenum disulfide powder is 10.9 µm. The comparative analysis of MoS2 particle's distribution as per size and valleys' sizes on turned and ground surfaces allow us to make a conclusion regarding the comparability of these values and principal possibility of micro valley's filling with MoS2 particles. MoS2 attachment to the near-surface layer of steel AISI 321, subjected to the turning (Ra= 2.15 µm) or grinding (Ra= 0.36 µm), is implemented by means of the microasperities deformation by an ultrasonic tool depending on the initials surface morphology.

  5. Modeling the Excess Cell Surface Stored in a Complex Morphology of Bleb-Like Protrusions.

    Directory of Open Access Journals (Sweden)

    Maryna Kapustina

    2016-03-01

    Full Text Available Cells transition from spread to rounded morphologies in diverse physiological contexts including mitosis and mesenchymal-to-amoeboid transitions. When these drastic shape changes occur rapidly, cell volume and surface area are approximately conserved. Consequently, the rounded cells are suddenly presented with a several-fold excess of cell surface whose area far exceeds that of a smooth sphere enclosing the cell volume. This excess is stored in a population of bleb-like protrusions (BLiPs, whose size distribution is shown by electron micrographs to be skewed. We introduce three complementary models of rounded cell morphologies with a prescribed excess surface area. A 2D Hamiltonian model provides a mechanistic description of how discrete attachment points between the cell surface and cortex together with surface bending energy can generate a morphology that satisfies a prescribed excess area and BLiP number density. A 3D random seed-and-growth model simulates efficient packing of BLiPs over a primary rounded shape, demonstrating a pathway for skewed BLiP size distributions that recapitulate 3D morphologies. Finally, a phase field model (2D and 3D posits energy-based constitutive laws for the cell membrane, nematic F-actin cortex, interior cytosol, and external aqueous medium. The cell surface is equipped with a spontaneous curvature function, a proxy for the cell surface-cortex couple, that is a priori unknown, which the model "learns" from the thin section transmission electron micrograph image (2D or the "seed and growth" model image (3D. Converged phase field simulations predict self-consistent amplitudes and spatial localization of pressure and stress throughout the cell for any posited stationary morphology target and cell compartment constitutive properties. The models form a general framework for future studies of cell morphological dynamics in a variety of biological contexts.

  6. Effect of droplet morphology on growth dynamics and heat transfer during condensation on superhydrophobic nanostructured surfaces.

    Science.gov (United States)

    Miljkovic, Nenad; Enright, Ryan; Wang, Evelyn N

    2012-02-28

    Condensation on superhydrophobic nanostructured surfaces offers new opportunities for enhanced energy conversion, efficient water harvesting, and high performance thermal management. These surfaces are designed to be Cassie stable and favor the formation of suspended droplets on top of the nanostructures as compared to partially wetting droplets which locally wet the base of the nanostructures. These suspended droplets promise minimal contact line pinning and promote passive droplet shedding at sizes smaller than the characteristic capillary length. However, the gas films underneath such droplets may significantly hinder the overall heat and mass transfer performance. We investigated droplet growth dynamics on superhydrophobic nanostructured surfaces to elucidate the importance of droplet morphology on heat and mass transfer. By taking advantage of well-controlled functionalized silicon nanopillars, we observed the growth and shedding behavior of suspended and partially wetting droplets on the same surface during condensation. Environmental scanning electron microscopy was used to demonstrate that initial droplet growth rates of partially wetting droplets were 6× larger than that of suspended droplets. We subsequently developed a droplet growth model to explain the experimental results and showed that partially wetting droplets had 4-6× higher heat transfer rates than that of suspended droplets. On the basis of these findings, the overall performance enhancement created by surface nanostructuring was examined in comparison to a flat hydrophobic surface. We showed these nanostructured surfaces had 56% heat flux enhancement for partially wetting droplet morphologies and 71% heat flux degradation for suspended morphologies in comparison to flat hydrophobic surfaces. This study provides insights into the previously unidentified role of droplet wetting morphology on growth rate, as well as the need to design Cassie stable nanostructured surfaces with tailored droplet

  7. Silver nanocrystals of various morphologies deposited on silicon wafer and their applications in ultrasensitive surface-enhanced Raman scattering

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Limiao, E-mail: chenlimiao@csu.edu.cn; Jing, Qifeng; Chen, Jun; Wang, Bodong; Huang, Jianhan; Liu, Younian

    2013-11-15

    Silver nanostructures with dendritic, flower-like and irregular morphologies were controllably deposited on a silicon substrate in an aqueous hydrogen fluoride solution at room temperature. The morphology of the Ag nanostructures changed from dendritic to urchin-like, flowerlike and pinecone-like with increasing the concentration of polyvinyl pyrrolidone (MW = 55,000) from 2 to 10 mM. The Ag nanostructures were characterized by transmission electron microscopy, high-resolution transmission electron microscopy, scanning electron microscopy, energy-dispersive X-ray, and X-ray diffraction. Through a series of time-dependent morphological evolution studies, the growth processes of Ag nanostructures have been systematically investigated and the corresponding growth mechanisms have been discussed. In addition, the morphology-dependent surface-enhanced Raman scattering of as-synthesized Ag nanostructures were investigated. The results indicated that flower-like Ag nanostructure had the highest activity than the other Ag nanostructures for Rhodamine 6G probe molecules. Highlights: • A simple method was developed to prepare dendritic and flower-like Ag nanostructures. • The flower-like Ag nanoparticles exhibit highest SERS activity. • The SERS substrate based on flower-like Ag particles can be used to detect melamine.

  8. Microscopic Investigation of Reversible Nanoscale Surface Size Dependent Protein Conjugation

    Directory of Open Access Journals (Sweden)

    Michael A. Carpenter

    2009-05-01

    Full Text Available Aβ1-40 coated 20 nm gold colloidal nanoparticles exhibit a reversible color change as pH is externally altered between pH 4 and 10. This reversible process may contain important information on the initial reversible step reported for the fibrillogenesis of Aβ (a hallmark of Alzheimer’s disease. We examined this reversible color change by microscopic investigations. AFM images on graphite surfaces revealed the morphology of Aβ aggregates with gold colloids. TEM images clearly demonstrate the correspondence between spectroscopic features and conformational changes of the gold colloid.

  9. Temperature-dependent morphology of hybrid nanoflowers from elastin-like polypeptides

    Directory of Open Access Journals (Sweden)

    Koushik Ghosh

    2014-02-01

    Full Text Available We report a method for creating hybrid organic-inorganic “nanoflowers” using calcium or copper ions as the inorganic component and a recombinantly expressed elastin-like polypeptide (ELP as the organic component. Polypeptides provide binding sites for the dynamic coordination with metal ions, and then such noncovalent complexes become nucleation sites for primary crystals of metal phosphates. We have shown that the interaction between the stimuli-responsive ELP and Ca2+ or Cu2+, in the presence of phosphate, leads to the growth of micrometer-sized particles featuring nanoscale patterns shaped like flower petals. The morphology of these flower-like composite structures is dependent upon the temperature of growth and has been characterized by scanning electron microscopy. The composition of nanoflowers has also been analyzed by energy-dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy, and X-ray diffraction. The temperature-dependent morphologies of these hybrid nanostructures, which arise from the controllable phase transition of ELPs, hold potential for morphological control of biomaterials in emerging applications such as tissue engineering and biocatalysis.

  10. Temperature-dependent morphology of hybrid nanoflowers from elastin-like polypeptides

    Energy Technology Data Exchange (ETDEWEB)

    Ghosh, Koushik; Balog, Eva Rose M.; Sista, Prakash; Williams, Darrick J.; Martinez, Jennifer S., E-mail: jenm@lanl.gov, E-mail: rcrocha@lanl.gov; Rocha, Reginaldo C., E-mail: jenm@lanl.gov, E-mail: rcrocha@lanl.gov [Center for Integrated Nanotechnologies, Materials Physics and Applications Division, Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States); Kelly, Daniel [Chemistry Division, Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States)

    2014-02-01

    We report a method for creating hybrid organic-inorganic “nanoflowers” using calcium or copper ions as the inorganic component and a recombinantly expressed elastin-like polypeptide (ELP) as the organic component. Polypeptides provide binding sites for the dynamic coordination with metal ions, and then such noncovalent complexes become nucleation sites for primary crystals of metal phosphates. We have shown that the interaction between the stimuli-responsive ELP and Ca{sup 2+} or Cu{sup 2+}, in the presence of phosphate, leads to the growth of micrometer-sized particles featuring nanoscale patterns shaped like flower petals. The morphology of these flower-like composite structures is dependent upon the temperature of growth and has been characterized by scanning electron microscopy. The composition of nanoflowers has also been analyzed by energy-dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy, and X-ray diffraction. The temperature-dependent morphologies of these hybrid nanostructures, which arise from the controllable phase transition of ELPs, hold potential for morphological control of biomaterials in emerging applications such as tissue engineering and biocatalysis.

  11. An expert system to characterize the surface morphological properties according to their functionalities

    International Nuclear Information System (INIS)

    Bigerelle, M; Mathia, T; Iost, A; Correvits, T; Anselme, K

    2011-01-01

    In this paper we propose a new methodology to characterize the morphological properties of a surface in relation with its functionality (tribological properties, surface coating adhesion, brightness, wettability...). We create a software based on experimental design and surface profile recording. Using an appropriate database structure, the roughness parameters are automatically computed at different scales. The surface files are saved in a hard disk directory and roughness parameters are computed at different scales. Finally, a statistical analysis system proposes the roughness parameter (or the pair of roughness parameters) that better describe(s) the functionality of the surface and the spatial scales at which the parameter(s) is (are) the more relevant.

  12. An expert system to characterize the surface morphological properties according to their functionalities

    Energy Technology Data Exchange (ETDEWEB)

    Bigerelle, M [Laboratoire Roberval, UMR 6253, UTC/CNRS, UTC Centre de Recherches de Royallieu BP 20529, 60205 Compiegne France stol BS1 6BE (United Kingdom); Mathia, T [Laboratoire de Tribologie et Dynamique des Systemes, UMR 5513, Ecole Centrale de Lyon, 36 Av Guy de Collongue, 69134 Ecully Cedex (France); Iost, A [Laboratoire de Mecanique de Lille, UMR CNRS 8107, Arts et Metiers ParisTech - Lille, 8, boulevard Louis XIV 59046 Lille (France); Correvits, T [Laboratoire de Metrologie. Arts et Metiers ParisTech, ENSAM, 8 boulevard Louis XIV, 59046 LILLE Cedex (France); Anselme, K, E-mail: maxence.bigerelle@utc.fr [Institut De Sciences Des Materiaux De Mulhouse, CNRS LRC 7228, 15, rue Jean Starcky, Universite De Haute-Alsace, BP 2488, 68057 Mulhouse (France)

    2011-08-19

    In this paper we propose a new methodology to characterize the morphological properties of a surface in relation with its functionality (tribological properties, surface coating adhesion, brightness, wettability...). We create a software based on experimental design and surface profile recording. Using an appropriate database structure, the roughness parameters are automatically computed at different scales. The surface files are saved in a hard disk directory and roughness parameters are computed at different scales. Finally, a statistical analysis system proposes the roughness parameter (or the pair of roughness parameters) that better describe(s) the functionality of the surface and the spatial scales at which the parameter(s) is (are) the more relevant.

  13. In situ Raman spectroscopy of LiFePO4: size and morphology dependence during charge and self-discharge

    Science.gov (United States)

    Wu, Jing; Krishna Phani Dathar, Gopi; Sun, Chunwen; Theivanayagam, Murali G.; Applestone, Danielle; Dylla, Anthony G.; Manthiram, Arumugam; Henkelman, Graeme; Goodenough, John B.; Stevenson, Keith J.

    2013-10-01

    Previous studies of the size dependent properties of LiFePO4 have focused on the diffusion rate or phase transformation pathways by bulk analysis techniques such as x-ray diffraction (XRD), neutron diffraction and electrochemistry. In this work, in situ Raman spectroscopy was used to study the surface phase change during charge and self-discharge on a more localized scale for three morphologies of LiFePO4: (1) 25 ± 6 nm width nanorods, (2) 225 ± 6 nm width nanorods and (3) ˜2 μm porous microspheres. Both the large nanorod and microsphere geometries showed incomplete delithiation at the end of charge, which was most likely caused by anti-site defects along the 1D diffusion channels in the bulk of the larger particles. Based on the in situ Raman measurements, all of the morphologies studied exhibited self-discharge with time. Among them, the smallest FePO4 particles self-discharged (lithiated) the fastest. While nanostructuring LiFePO4 can offer advantages in terms of lowering anti-site defects within particles, it also creates new problems due to high surface energies that allow self-discharge. The in situ Raman spectroscopy also showed that carbon coating did not provide significant improvement to the stability of the lithiated particles.

  14. Molecular weight dependence of the morphology in P3HT:PCBM solar cells.

    Science.gov (United States)

    Liu, Feng; Chen, Dian; Wang, Cheng; Luo, Kaiyuan; Gu, Weiyin; Briseno, Alejandro L; Hsu, Julia W P; Russell, Thomas P

    2014-11-26

    In polymer-based photovoltaic devices, optimizing and controlling the active layer morphology is important to enhancing the device efficiency. Using poly(3-hexylthiophene) (P3HT) with well-defined molecular weights (MWs), synthesized by the Grignard metathesis (GRIM) method, we show that the morphology of the photovoltaic active layer and the absorption and crystal structure of P3HT are dependent on the MW. Differential scanning calorimetry showed that the crystallinity of P3HT reached a maximum for intermediate MWs. Grazing-incidence wide-angle X-ray diffraction showed that the spacing of the (100) planes of P3HT increased with increasing MW, while the crystal size decreased. Nonlinear crystal lattice expansions were found for both the (100) and (020) lattice planes, with an unusual π-π-stacking enhancement observed between 50 and 100 °C. The melting point depression for P3HT, when mixed with [6,6]-phenyl-C61-butyric acid methyl ester (PCBM), and, hence, the Flory-Huggins interaction parameter depended on the MW. PCBM was found to perturb the ordering of P3HT chains. In photovoltaic devices, P3HT with a MW of ∼20K showed the best device performance. The morphologies of these blends were studied by grazing-incidence small-angle X-ray scattering (GISAXS) and resonant soft X-ray scattering. In GISAXS, we observed that the low-molecular-weight P3HT more readily crystallizes, promoting a phase-separated morphology.

  15. Influences of chemical aging on the surface morphology and crystallization behavior of basaltic glass fibers

    DEFF Research Database (Denmark)

    Lund, Majbritt Deichgræber; Yue, Yuanzheng

    2008-01-01

    The impact of aging in high humidity and water on the surface morphology and crystallization behavior of basaltic glass fibers has been studied using scanning electron microscopy, transmission electron microscopy, calorimetry and X-ray diffraction. The results show that interaction between...... the fibers and the surrounding media (high humidity or water at 70 C) leads to chemical changes strongly affecting the surface morphology. The crystallization peak temperature of the basaltic glass fibers are increased without changing the onset temperature, this may be caused by a chemical depletion...

  16. Surface reactivity, cytotoxic, and morphological transforming effects of diatomaceous Earth products in Syrian hamster embryo cells.

    Science.gov (United States)

    Elias, Zoé; Poirot, Odile; Fenoglio, Ivana; Ghiazza, Mara; Danière, Marie-Céleste; Terzetti, Francine; Darne, Christian; Coulais, Catherine; Matekovits, Ildiko; Fubini, Bice

    2006-06-01

    In order to evaluate the effect of thermal treatments on the surface reactivity and carcinogenic potential of diatomaceous earth (DE) products, the physicochemical features of some specimens--derived by heating the same original material--were compared with their cytotoxic and transforming potency. The samples were an untreated DE (amorphous) progressively heated in the laboratory at 900 degrees C (DE 900) and 1200 degrees C (DE 1200) and a commercial product manufactured from the same DE (Chd) from which the finer fraction ( Chd > DE 900 > DE, suggesting that on heating, the surface acquires a higher potential for free radical release. Most of the silica samples generated COO* radicals from the formate ion, following homolytic rupture of the carbon-hydrogen bond, in the presence of ascorbic acid. A concentration-dependent decrease in cell proliferation and colony-forming efficiency was observed in SHE cultures treated with Chd-F, Chd, and DE. Heating abolished DE cytotoxicity but conferred a transforming ability to thermal treated particles. DE was the only sample that did not induce morphological transformation of cells. According to their transformation capacity, the samples were classified as follows: Chd-F > Chd, DE 1200 > DE 900 > DE. Taken together, the reported results suggest that (1) the transforming potential of a biogenic amorphous silica is related to the thermal treatment that transforms the original structure in cristobalite and generates surface active sites; (2) the reactivity of samples in releasing *OH radicals correlates to their transforming ability; (3) the finer fraction of the commercial product is significantly more toxic and transforming than the coarse dust; and (4) opposite to silica dusts of mineral origin, which loose both cytotoxicity and transforming ability upon heating, heated diatomite acquires a cell-transforming potency. DE products should be thus considered a set apart of silica-based potentially toxic materials.

  17. Inelastic surface vibrations versus energy-dependent nucleus ...

    Indian Academy of Sciences (India)

    Abstract. Limitations of the static Woods–Saxon potential and the applicability of the energy- dependent Woods–Saxon potential (EDWSP) model within the framework of one-dimensional. Wong formula to explore the sub-barrier fusion data are highlighted. The inelastic surface exci- tations of the fusing nuclei are found to ...

  18. Inelastic surface vibrations versus energy-dependent nucleus ...

    Indian Academy of Sciences (India)

    Limitations of the static Woods–Saxon potential and the applicability of the energy dependent Woods–Saxon potential (EDWSP) model within the framework of one-dimensional Wong formula to explore the sub-barrier fusion data are highlighted. The inelastic surface excitations of the fusing nuclei are found to be ...

  19. Rheology and Morphology of PP/ionomer/clay Nancomposites Depending on Selective Dispersion of Organoclays

    International Nuclear Information System (INIS)

    Kim, Doohyun; Ock, Hyun Geun; Ahn, Kyung Hyun; Lee, Seung Jong

    2015-01-01

    In this study, structural developments of polypropylene / ionomer / clay ternary composites were investigated depending on the dispersion and localization of clay. The changes in physical properties were observed adding organoclays 1-10wt% to 90% polypropylene and 10% ionomer blends. The organoclays were localized inside of the dispersed phase under the composition of 3wt%, however, over that composition, clay particles formed stiff network structure in the dispersed phase and additional clays were localized at the interface between two phases. According to the developments of microstructure, the interaction of ternary composites changed from polypropylene-ionomer to polypropylene- ionomer and ionomer-clay which affected rheological properties. The storage modulus (G') of the composites was similar to the blends when clays were localized inside of dispersed phase but increased when clays were localized at interface. Also, the fractured morphology of the composites showed phase boundary and growing radius of dispersed phase depending on addition of fillers when clays were found inside. However, when fillers found at the interface between blends, the radius of the dispersed phase decreased and compatibilized morphology were observed. The interfacial interaction of the ternary composite was quantified depending on the structural development of dispersed phase and localization of clay particles by the rheological properties. The interaction of composites at solid state which was measured through peel adhesion strength increased by growth of interfacial interaction of each component. Furthermore, the crystallinity of the composites was decreased when the clay particles were localized at the interface.

  20. Morphology-Dependent Resonances and Their Applications to Sensing in Aerospace Environments

    Science.gov (United States)

    Adamovsky, G.; Otugen, M.V.

    2009-01-01

    This paper reviews recent developments in Morphology-Dependent Resonance (MDR)-based sensors for aerospace applications. The sensor concept is based on the detection of small shifts of optical resonances (also called the whispering gallery modes or WGM) of dielectric spheres caused by external effects. Recent developments in MRD-based micro-optical sensors for temperature, force, pressure, and concentration are discussed. In addition to the experimental configurations used in each type of prototype sensor, a brief overview is also given for analytical approaches to describe the sensor principle.

  1. Optical properties and surface morphology studies of palladium contacts on mercuric iodide single crystals

    Energy Technology Data Exchange (ETDEWEB)

    George, M.A.; Azoulay, M.; Burger, A.; Biao, Y.; Silberman, E. [Fisk Univ., Nashville, TN (United States). Dept. of Physics; Nason, D. [EG and G Energy Measurements, Inc., Goleta, CA (United States). Santa Barbara Operations

    1993-05-01

    Palladium is chemically suitable for electric contacts on mercuric iodide detectors for photon and nuclear radiation detection, so the understanding of palladium contacts is important for fundamental and practical scientific purposes. A study has been conducted on the surface morphology of evaporated contacts using Atomic Force Microscopy (AFM) and optical transmission and reflection. Evaporated palladium coatings are typically nonuniform and may deposit selectively on mercuric iodide surface defects. Reflection measurements show that coating thickness and surface treatment affect intensity, position and shape of a reflected peak characteristic of the mercuric iodide structure. Results indicate that the band gap energy in the surface of the mercuric iodide is lowered by palladium contacts.

  2. [MORPHOLOGICAL CHANGES OF THE LIVER IN OBTURATION JAUNDICE, CAUSED BY CHOLEDOCHOLITHIASIS, DEPENDING ON ITS DURATION].

    Science.gov (United States)

    Sipliviy, V A; Yevtushenko, D V; Naumova, O V; Andreyeshchev, S A; Yevtushenko, A V

    2016-02-01

    Abstract The results of surgical treatment of 184 patients for obturation jaundice, caused by choledocholithiasis, were analyzed. Morphological changes of the liver were studied in 20 patients. There were three groups of patients delineated, depending on the obturation jaundice duration: up to 7 days, from 8 to 14 days, more than 15 days, and also a group of patients after the bile outflow restoration. The obturation jaundice occurrence in choledocholithiasis is accompanied by significant morphological changes in the liver, severity of which is enhancing while the obturation jaundice persistence increasing. While persistence of obturation jaundice through 8 days and more the connective tissue volume is enhancing, a relative volume of hepatocytes is reducing and a stromal-parenchymatous index is increasing. The bile outflow restoration secures significant reduction of intensity of alterative and inflammatory changes in hepatic parenchyma, as well as activation of reparative processes in the tissue. In cholangitis, caused by P. aeruginosa and E. coli, according to morphological investigations data, in the liver a diffuse purulent cholangitis on background of chronic changes in accordance to duration of the obturation jaundice persists.

  3. [DEVELOPMENT OF FUNCTIONAL AND MORPHOLOGICAL CHANGES OF A PANCREAS DEPENDING ON THE DURATION OF OBSTRUCTIVE CHOLESTASIS].

    Science.gov (United States)

    Belyaev, A N; Kostin, S V; Belyaev, S A

    2015-01-01

    To study the severity and timing of the development of functional (reversible) and morphological (irreversible) disturbances in the pancreas, depending on the duration of obstructive cholestasis. Obstructive jaundice in the experiment 18 dogs modeled by applying the loop stranglehold on the common bile duct, followed by observation for 30 days. We measured total bilirubin and fractions aspartate aminotransferase activity (AST) and alanine aminotransferase (ALT), the contents alpha-amylase, pancreatic lipase, glucose, histological examination of the pancreas (magnification of 100 times and 400). On day 3 the common bile duct obstruction bilirubin increased from 7.1 to 286.8 μmol/l, ALT--from 0.17 to 4.18 μmol*h/l, alpha-amylase from 89 to 186 U/L and lipase--to 68 to 179 U/L. Then there was a slight decrease in the parameters studied with repeated their increase to 15 hours. Morphological changes in the first three days were characterized by reversible (swelling), impaired organ that 14-16 days passed in organic (irreversible) changes. Dynamics of fluctuations in the level of liver enzymes in the pancreas and obstructive cholestasis correlates with morphological abnormalities in the pancreas and fit into the concept of general biological organism's reaction to injury.

  4. Effect of surface morphology on the fracture strength of silicon nanobeams

    Science.gov (United States)

    Alan, Tuncay; Hines, Melissa A.; Zehnder, Alan T.

    2006-08-01

    The effect of nanoscale surface morphology on the fracture strength of 190-nm-thick, doubly clamped Si beams was measured experimentally. The surface morphology was controlled through aqueous etching and characterized by atomic force microscopy. The beams fractured along the primary cleavage planes, {111}. Fracture strength was extracted using finite element simulations of the experiment. Nanobeams etched with relatively smooth morphologies (0.4nm rms) were able to sustain a tensile stress of 15.8GPa, close to theoretical strengths predicted by previous atomistic calculations. In contrast, nanobeams decorated with nanometer-high step bunches (1.5nm rms) had a 20% lower fracture strength, 12.8GPa, suggesting that careful attention to processing is necessary for maximum strength.

  5. [Morphology of cracks in enamel surface produced experimentally using high and low temperature].

    Science.gov (United States)

    Suárez Quintanilla, J; Segade, L A; González Bahillo, J

    1989-12-01

    A scanning electron microscope study was made to study the morphological changes in the human enamel surface produced by low and high temperatures. Cracked dental enamel was observed when the teeth were exposed at low and high temperatures. When the time of exposition was increased, there are more enamel cracks which may be considered as enamel fractures.

  6. Surface Morphology and Optical Properties of 3 Porphyrin/Au and Au/Porphyrin/Au Systems

    Czech Academy of Sciences Publication Activity Database

    Kalachyova, Y.; Lyutakov, O.; Solovyev, Andrey; Slepička, P.; Švorčík, V.

    2013-01-01

    Roč. 8, DEC 27 (2013), s. 547 ISSN 1931-7573 Grant - others:GA ČR(CZ) GPP108/11/P840; GA ČR(CZ) GAP108/12/1168 Program:GA Institutional support: RVO:67985858 Keywords : nanostructures * gold * porphyrin * luminescence * enhancement * surface morphology Subject RIV: JJ - Other Materials Impact factor: 2.524, year: 2012

  7. The theory of development of surface morphology by sputter erosion processes

    International Nuclear Information System (INIS)

    Carter, G.; Nobes, M.J.

    1984-01-01

    When a surface is bombarded by an energetic ion flux a rich variety of surface structures are observed to develop at the atomic, microscopic and macroscopic scales. Such structures include elevated, with respect to the surrounding surface, features such as mesas or plateaux, ridges, cones and pyramids and depressed features such as etch pits and cavities. These elementary features may be isolated or in profusion and frequently repetitive patterns of coordinated pyramidal structures, etch pits, surface ledges or facets and ripple or wave-like structures occur. The majority of the features arise rather directly from the erosion action of the sputtering process, particularly from differential erosion processes at different surface localities. The authors outline a general approach to sputter erosion induced surface morphology development based on the concept of the surface as an advancing wave. (Auth.)

  8. Study of the Effect of Nanoparticles and Surface Morphology on Reverse Osmosis and Nanofiltration Membrane Productivity

    Directory of Open Access Journals (Sweden)

    Steven J. Duranceau

    2013-08-01

    Full Text Available To evaluate the significance of reverse osmosis (RO and nanofiltration (NF surface morphology on membrane performance, productivity experiments were conducted using flat-sheet membranes and three different nanoparticles, which included SiO2, TiO2 and CeO2. In this study, the productivity rate was markedly influenced by membrane surface morphology. Atomic force microscopy (AFM analysis of membrane surfaces revealed that the higher productivity decline rates associated with polyamide RO membranes as compared to that of a cellulose acetate NF membrane was due to the inherent ridge-and-valley morphology of the active layer. The unique polyamide active layer morphology was directly related to the surface roughness, and was found to contribute to particle accumulation in the valleys causing a higher flux decline than in smoother membranes. Extended RO productivity experiments using laboratory grade water and diluted pretreated seawater were conducted to compare the effect that different nanoparticles had on membrane active layers. Membrane flux decline was not affected by particle type when the feed water was laboratory grade water. On the other hand, membrane productivity was affected by particle type when pretreated diluted seawater served as feed water. It was found that CeO2 addition resulted in the least observable flux decline, followed by SiO2 and TiO2. A productivity simulation was conducted by fitting the monitored flux data into a cake growth rate model, where the model was modified using a finite difference method to incorporate surface thickness variation into the analysis. The ratio of cake growth term (k1 and particle back diffusion term (k2 was compared in between different RO and NF membranes. Results indicated that k2 was less significant for surfaces that exhibited a higher roughness. It was concluded that the valley areas of thin-film membrane surfaces have the ability to capture particles, limiting particle back diffusion.

  9. Surface morphology changes of acrylic resins during finishing and polishing phases

    Directory of Open Access Journals (Sweden)

    Glaucio Serra

    2013-12-01

    Full Text Available INTRODUCTION: The finishing and polishing phases are essential to improve smoothness and shining on the surface of acrylic resins used to make removable orthodontic appliances. A good surface finishing reduces roughness, which facilitates hygiene, prevents staining and provides greater comfort to the patients. OBJECTIVE: The aim of this paper was to analyze the changes on surface morphology of acrylic resins during finishing and polishing phases. METHODS: Thirty discs (10 mm in diameter and 5 mm in length were made with acrylic resin and randomly divided into ten groups. The control group did not receive any treatment while the other groups received gradual finishing and polishing. The last group received the entire finishing and polishing procedures. Surface morphology was qualitatively analyzed through scanning electron microscopy and quantitatively analyzed through a laser profilometer test. RESULTS: The acrylic resin surfaces without treatment showed bubbles which were not observed in the subsequent phases. Wearing out with multilaminated burs, finishing with wood sandpaper and finishing with water sandpaper resulted in surfaces with decreasing irregularities. The surfaces that were polished with pumice and with low abrasive liquids showed high superficial smoothness. CONCLUSION: Highly smooth acrylic resin surfaces can be obtained after mechanical finishing and polishing performed with multilaminated burs, wood sandpaper, water sandpaper, pumice and low abrasive liquids.

  10. Surface topography during neural stem cell differentiation regulates cell migration and cell morphology.

    Science.gov (United States)

    Czeisler, Catherine; Short, Aaron; Nelson, Tyler; Gygli, Patrick; Ortiz, Cristina; Catacutan, Fay Patsy; Stocker, Ben; Cronin, James; Lannutti, John; Winter, Jessica; Otero, José Javier

    2016-12-01

    We sought to determine the contribution of scaffold topography to the migration and morphology of neural stem cells by mimicking anatomical features of scaffolds found in vivo. We mimicked two types of central nervous system scaffolds encountered by neural stem cells during development in vitro by constructing different diameter electrospun polycaprolactone (PCL) fiber mats, a substrate that we have shown to be topographically similar to brain scaffolds. We compared the effects of large fibers (made to mimic blood vessel topography) with those of small-diameter fibers (made to mimic radial glial process topography) on the migration and differentiation of neural stem cells. Neural stem cells showed differential migratory and morphological reactions with laminin in different topographical contexts. We demonstrate, for the first time, that neural stem cell biological responses to laminin are dependent on topographical context. Large-fiber topography without laminin prevented cell migration, which was partially reversed by treatment with rock inhibitor. Cell morphology complexity assayed by fractal dimension was inhibited in nocodazole- and cytochalasin-D-treated neural precursor cells in large-fiber topography, but was not changed in small-fiber topography with these inhibitors. These data indicate that cell morphology has different requirements on cytoskeletal proteins dependent on the topographical environment encountered by the cell. We propose that the physical structure of distinct scaffolds induces unique signaling cascades that regulate migration and morphology in embryonic neural precursor cells. J. Comp. Neurol. 524:3485-3502, 2016. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

  11. Dry Etching of Copper Phthalocyanine Thin Films: Effects on Morphology and Surface Stoichiometry

    Directory of Open Access Journals (Sweden)

    Michael J. Brett

    2012-08-01

    Full Text Available We investigate the evolution of copper phthalocyanine thin films as they are etched with argon plasma. Significant morphological changes occur as a result of the ion bombardment; a planar surface quickly becomes an array of nanopillars which are less than 20 nm in diameter. The changes in morphology are independent of plasma power, which controls the etch rate only. Analysis by X-ray photoelectron spectroscopy shows that surface concentrations of copper and oxygen increase with etch time, while carbon and nitrogen are depleted. Despite these changes in surface stoichiometry, we observe no effect on the work function. The absorbance and X-ray diffraction spectra show no changes other than the peaks diminishing with etch time. These findings have important implications for organic photovoltaic devices which seek nanopillar thin films of metal phthalocyanine materials as an optimal structure.

  12. Growth kinetics and morphology of a ballistic deposition model that incorporates surface diffusion for two species

    International Nuclear Information System (INIS)

    El-Nashar, H.F.; Cerdeira, H.A.

    1998-08-01

    We introduce a ballistic deposition model for two kinds of particles (active and inactive) in (2+1) dimensions upon introducing the surface diffusion for the inactive particles. A morphological structural transition is found as the probability of being the inactive particle increases. This transition is well defined by the change in the behavior of the surface width when it is plotted versus time and probability. The exponents α and β calculated for different values of probability show the same behavior. The presence of both types of particles issues three different processes that control the growing surface: overhanging, nonlocal growth and diffusion. It finally leads to a morphological structural transition where the universality changes away from that of Kardar-Parisi-Zhang, in (2+1) dimensions, but not into Edwards-Wilkinson's. (author)

  13. Surface Morphology and Tooth Adhesion of a Novel Nanostructured Dental Restorative Composite

    Directory of Open Access Journals (Sweden)

    Marco Salerno

    2016-03-01

    Full Text Available Recently, a novel dental restorative composite based on nanostructured micro-fillers of anodic porous alumina has been proposed. While its bulk properties are promising thanks to decreased aging and drug delivery capabilities, its surface properties are still unknown. Here we investigated the surface morphology and the adhesion to tooth dentin of this composite as prepared. For comparison, we used two commercial composites: Tetric EVO Flow (Ivoclar and Enamel HRi Plus (Micerium. The surface morphology was characterized by atomic force microscopy and the adhesion strength by tensile tests. The experimental composite is rougher than the commercial composites, with root mean square roughness of ~549 nm against 170–511 nm, and presents an adhesion strength of ~15 MPa against 19–21 MPa. These results show at the same time some proximity to the commercial composites, but also the need for optimization of the experimental material formulation.

  14. Characterization of the corroded surface morphology of a carbon steel piping elbow affected by flow-accelerated corrosion

    International Nuclear Information System (INIS)

    Abe, Hiroshi; Watanabe, Yutaka; Nakashima, Makoto; Tatsuki, Tadashi

    2017-01-01

    It has been widely recognized that the inner surface of carbon steel piping affected by relatively severe flow-accelerated corrosion (FAC) shows typical morphology in terms of roughness in many cases. Although hydrodynamic parameters would determine the characteristics of the rough surface developed in such cases, the detailed mechanism of the roughness formation is not fully known. In this study, the local FAC rate profile and morphology in terms of surface roughness for an entire 90-degree carbon steel piping elbow used in a fossil power plant have been investigated under two-phase flow in order to discuss the relationships between the FAC rate and characteristics of the inner surface morphology. For the axial direction, the FAC rate gradually increased with distance from the inlet, and it reaches the peak value in the downstream side, beyond which, the value kept decreasing slightly. Distributed horse-shoe pits and scalloped patterns were observed on the extrados side. The finding suggests that the extrados side of the pipe wall was covered with a continuous liquid film (single-phase). The result shows the possibility of the occurrence of FAC by a single-phase flow in the area where there is a sudden change in flow regime, even when the nominal phase state of the fluid is a two-phase flow regime. Both the local FAC rate and scallop coverage increase steeply near the middle parts of the elbow. There was a good correlation between the two, but it was not a one-to-one relationship because a significant decrease in FAC rate was observed in the downstream side; in contrast, the entire surface was covered with a fine scalloped pattern. The change in the morphology in terms of surface roughness clearly indicated that the overlapping of horse-shoe shaped pits gave a scalloped appearance. The results revealed that the inner surface shape affected by FAC is considered to essentially depend on the number density of nucleation sites for pit formation. (author)

  15. Activity-dependent myelination of parvalbumin interneurons mediated by axonal morphological plasticity.

    Science.gov (United States)

    Stedehouder, J; Brizee, D; Shpak, G; Kushner, S A

    2018-03-05

    Axonal myelination of neocortical pyramidal neurons is dynamically modulated by neuronal activity. Recent studies have shown that a substantial proportion of neocortical myelin content is contributed by fast-spiking, parvalbumin (PV)-positive interneurons. However, it remains unknown whether the myelination of PV + interneurons is also modulated by intrinsic activity. Here, we utilized cell-type specific Designer Receptors Exclusively Activated by Designer Drugs (DREADDs) in adult male and female mice to activate a sparse population of medial prefrontal cortex PV + interneurons. Using single-cell axonal reconstructions, we find that DREADD-stimulated PV + interneurons exhibit a nearly two-fold increase in total length of myelination, predominantly mediated by a parallel increase of axonal arborization and number of internodes. In contrast, the distribution of axonal inter-branch segment distance and myelin internode length were not significantly altered. Topographical analysis revealed that myelination of DREADD-stimulated cells extended to higher axonal branch orders, while retaining a similar inter-branch distance threshold for myelination. Together, our results demonstrate that chemogenetically-induced neuronal activity increases the myelination of neocortical PV + interneurons mediated at least in part by an elaboration of their axonal morphology. SIGNIFICANCE STATEMENT Myelination is the wrapping of an axon in order to optimize conduction velocity in an energy-efficient manner. Previous studies have shown that myelination of neocortical pyramidal neurons is experience and activity-dependent. We now show that activity-dependent myelin plasticity in the adult neocortex extends to parvalbumin-expressing fast-spiking interneurons. Specifically, chemogenetic stimulation of parvalbumin interneurons in the medial prefrontal cortex significantly enhanced axonal myelination, which was paralleled by an increase in axonal arborization. This suggests that activity-dependent

  16. Investigation of physical properties and surface morphology of Cu nanolayer deposited on glass and (Al, Fe) thin films by DC magnetron sputtering

    Energy Technology Data Exchange (ETDEWEB)

    Eslami, P.A. [Islamic Azad Univ., North Tehran (Iran, Islamic Republic of). Dept. of Chemistry; Islamic Azad Univ., Tabriz (Iran, Islamic Republic of). Dept. of Science-Applied Chemistry; Laheghi, S.N.; Ghoranneviss, M. [Islamic Azad Univ., Tehran (Iran, Islamic Republic of). Plasma Research Center; Moradi, S. [Islamic Azad Univ., Tehran (Iran, Islamic Republic of). Dept. of Chemistry; Aberumand, P. [Islamic Azad Univ., Tehran (Iran, Islamic Republic of). Science and Research Laboratory Complex

    2008-07-01

    The applications for copper (Cu) thin films with micro or nanostructural dimensions range from catalysis to microelectronic devices. This paper reported on a study in which DC magnetron sputtering was used to coat iron (Fe), copper (Cu) and aluminum (Al) on glass substrate under a particular voltage, time and optimized deposition pressure. The samples were then coated with Cu using the same technique in preparation of different multilayers. Physical properties such as transmission and reflection per cent, magnetic and electrical properties, size and surface morphology were analyzed using data from AFM, XRD, SEM, Four point probe, and magneto resistive spectrophotometers. The study showed that the size, surface morphology and some physical properties of Cu nanolayer depend on substrate materials, surface morphology and physical properties below the nanolayer. Future work will focus on chemical properties such as catalytic and electrochemical properties. Copper nanoparticles will also be synthesized on other materials such as ZnO. 14 refs., 1 tab., 3 figs.

  17. Effect of fast mold surface temperature evolution on iPP part morphology gradients

    Science.gov (United States)

    Liparoti, Sara; Sorrentino, Andrea; Guzman, Gustavo; Cakmak, Mukerrem; Titomanlio, Giuseppe

    2016-03-01

    The control of mold surface temperature is an important factor that affects the sample surface morphology as well as the structural gradients (orientation crystal size, and type) as well as cooling stresses. The frozen layer thickness formed during the filling stage also has a very significant effect on the flow resistance and thus on the resulting pressure drop and flow length in thin wall parts. The possibility to have a hot mold during filling and a quick cooling soon afterward is a significant process enhancement particularly for specialized applications such as micro injection molding and for the reproduction of micro structured surfaces. Up to now, several methods (electromagnetic, infrared, hot vapor fleshing etc,) were tried to achieve fast temperature evolution of the mold. Unfortunately, all these methods require a complex balance between thermal and mechanical problems, equipment cost, energy consumption, safety, molding cycle time and part quality achievable. In this work, a thin electrical resistance was designed and used to generate a fast and confined temperature variation on mold surface (by joule effect). Since the whole temperature evolution can take place in a few seconds, one can couple the advantages of a high surface temperature during filling with the advantages of a low mold temperature, fast cooling and low heating dissipation. Some experiments were performed with a commercial iPP resin. The effects of the surface temperature and of the heating time (under constant electric power) on surface finishing and on the final morphology (thickness and structure of the different layers) are explored and discussed.

  18. Identification card and codification of the chemical and morphological characteristics of 14 dental implant surfaces.

    Science.gov (United States)

    Dohan Ehrenfest, David M; Vazquez, Lydia; Park, Yeong-Joon; Sammartino, Gilberto; Bernard, Jean-Pierre

    2011-10-01

    Dental implants are commonly used in daily practice; however, most surgeons do not really know the characteristics of these biomedical devices they are placing in their patients. The objective of this work is to describe the chemical and morphological characteristics of 14 implant surfaces available on the market and to establish a simple and clear identification (ID) card for all of them, following the classification procedure developed in the Dohan Ehrenfest et al (2010) Codification (DEC) system. Fourteen implant surfaces were characterized: TiUnite (Nobel Biocare), Ospol (Ospol), Kohno HRPS (Sweden & Martina), Osseospeed (AstraTech), Ankylos (Dentsply Friadent), MTX (Zimmer), Promote (Camlog), BTI Interna (Biotechnology Institute), EVL Plus (SERF), Twinkon Ref (Tekka), Ossean (Intra-Lock), NanoTite (Biomet 3I), SLActive (ITI Straumann), Integra-CP/NanoTite (Bicon). Three samples of each implant were analyzed. Superficial chemical composition was analyzed using X-ray photoelectron spectroscopy/electron spectroscopy for chemical analysis, and the 100 nm in-depth profile was established using Auger electron spectroscopy. The microtopography was quantified using light interferometry. The general morphology and nanotopography were evaluated using a field emission-scanning electron microscope. Finally, the characterization code of each surface was established using the DEC system, and the main characteristics of each surface were summarized in a reader-friendly ID card. From a chemical standpoint, of the 14 different surfaces, 10 were based on a commercially pure titanium (grade 2 or 4), 3 on a titanium-aluminum alloy (grade 5 titanium), and one on a calcium phosphate core. Nine surfaces presented different forms of chemical impregnation or discontinuous coating of the titanium core, and 3 surfaces were covered with residual aluminablasting particles. Twelve surfaces presented different degrees of inorganic pollutions, and 2 presented a severe organic pollution

  19. Bio-Tribology Properties of Bionic Carp Scale Morphology on Ti6A14V Surface

    Science.gov (United States)

    Wang, W.; Y Wei, X.; Meng, K.; Zhong, L. H.; Wang, Y.; Yu, X. H.

    2017-12-01

    In order to improve the bio-tribology properties of Ti6A14V surface, the bionic carp scale appearance pattern on Ti6A14V surface was prepared by laser surface texturing technology. The ball-disc reciprocating linear tribological experiment under different lubricants with dry friction was carried out by MRTR multifunction friction and wear testing machine using ZrO2/Ti6A14V as friction pair. The wear scar morphology of the sample surface was observed by SEM. The results show that for dry friction, the friction factor of the bionic carp scale morphology Ti6A14V reduces by 0.23 than those without bionic carp scale morphology, a decline of 45%. Under different lubrication conditions, the friction factors of samples with the bionic carp scale are increased in varying degrees with the increase of size of bionic texturing. The friction factor with same specimen under different lubrication conditions according to the ascending order are 0.5g/dl of sodium hyaluronate +0.5g/dl-γglobulin and 0.5g/dl mixed aqueous solution of sodium hyaluronate solution and artificial saliva. The wear volume also showed a similar variation.

  20. Dwell time dependent morphological transition and sputtering yield of ion sputtered Sn

    International Nuclear Information System (INIS)

    Qian, H X; Zeng, X R; Zhou, W

    2010-01-01

    Self-organized nano-scale patterns may appear on a wide variety of materials irradiated with an ion beam. Good manipulation of these structures is important for application in nanostructure fabrication. In this paper, dwell time has been demonstrated to be able to control the ripple formation and sputtering yield on Sn surface. Ripples with a wavelength of 1.7 μm were observed for a dwell time in the range 3-20 μs, whereas much finer ripples with a wavelength of 540 nm and a different orientation were observed for a shorter dwell time in the range 0.1-2 μs. The sputtering yield increases with dwell time significantly. The results provide a new basis for further steps in the theoretical description of morphology evolution during ion beam sputtering.

  1. The effect of surface morphology on the primary fixation strength of uncemented femoral knee prosthesis: a cadaveric study

    NARCIS (Netherlands)

    Berahmani, S.; Janssen, D.W.; Wolfson, D.; Rivard, K.; Waal Malefijt, M.C. de; Verdonschot, N.J.

    2015-01-01

    We investigated the effect of surface morphology on the mechanical performance of uncemented femoral knee prosthesis. Eighteen implants were implanted on nine paired femurs and then pushed-off (left legs: a novel surface morphology; right legs: Porocoat as baseline). Bone mineral density (BMD) and

  2. Investigation on effects of surface morphologies on response of LPG sensor based on nanostructured copper ferrite system

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Satyendra [Nanomaterials and Sensors Research Laboratory, Department of Physics, University of Lucknow, Lucknow 226007, U.P. (India); Yadav, B.C., E-mail: balchandra_yadav@rediffmail.com [Nanomaterials and Sensors Research Laboratory, Department of Physics, University of Lucknow, Lucknow 226007, U.P. (India); Department of Applied Physics, School for Physical Sciences, Babasaheb Bhimrao Ambedkar University, Lucknow 226025, U.P. (India); Gupta, V.D. [Nanomaterials and Sensors Research Laboratory, Department of Physics, University of Lucknow, Lucknow 226007, U.P. (India); Dwivedi, Prabhat K. [DST Unit on Nanosciences, Department of Chemical Engineering, Indian Institute of Technology Kanpur, Kanpur, U.P. (India)

    2012-11-15

    Graphical abstract: Figure shows the variations in resistance with time for copper ferrite system synthesized in various molar ratio. A maximum variation in resistance was observed for copper ferrite prepared in 1:1 molar ratio. Highlights: ► Evaluation of structural, optical and surface morphologies. ► Significant variation in LPG sensing properties. ► Surface modification of ferric oxide pellet by copper ferrite. ► CuFe{sub 2}O{sub 4} pellets for LPG sensing at room temperature. -- Abstract: Synthesis of a copper ferrite system (CuFe{sub 2}O{sub 4}) via chemical co-precipitation method is characterized by X-ray diffraction, surface morphology (scanning electron microscope) and optical absorption spectroscopy. These characteristics show their dependence on the relative compositions of the two subsystems. They are further confirmed by the variation in the band gap. A study of gas sensing properties shows the spinel CuFe{sub 2}O{sub 4} synthesized in 1:1 molar ratio exhibit best response to LPG adsorption/resistance measurement. Thus resistance based LPG sensor is found robust, cheap and may be applied for kitchens and industrial applications.

  3. Anatomic - morphological features of qualified water polo players depending on game role

    Directory of Open Access Journals (Sweden)

    O. V. Poproshaev

    2014-01-01

    Full Text Available Purpose : to analyze the anatomic - morphological features of qualified water polo players depending on game role. Material : the study group consisted of 41 athlete. Assessing the level of physical development was carried out in terms of water polo in body size, body weight, chest excursion, lung capacity, power brush. Results : it was found that the central strikers - powerful players with significant muscle mass. They are the following indicators: length of the arm (22%, the length of the tibia (11%, foot length (7%, shoulder width (10% and vital capacity (11%. Central defenders - tall, sinewy athletes, which is characterized by long limbs. They highlighted the special role of the indicator arm's length (part of which is 34 % and vital capacity (10%. Midfielders or moving forwards - players of medium height and basic anthropometric indicators inferior players other roles, but exceed them in the values of the indicator lung capacity. Conclusion : these results relate to the functions that do the athletes on the field.

  4. Surface morphological, mechanical and thermal characterization of electron beam irradiated fibers

    International Nuclear Information System (INIS)

    Choi, Hae Young; Han, Seong Ok; Lee, Jung Soon

    2008-01-01

    The surface morphology of henequen irradiated by electron beam has been investigated by atomic force microscopy (AFM). Also, the extents to which electron beam irradiation affected the tensile and thermal properties of henequen fiber were investigated with Instron tensile tests and thermogravimetric analysis (TGA). The AFM studies showed that the pectin, waxy and primary layers (P) of henequen fiber, which have heterogeneous structures, were removed from the fiber surface by electron beam irradiation. The tensile strength and thermal stability of henequen fiber decreased with increasing dose of electron beam. At the irradiation of 10 kGy, the surface roughness increased because of the removal of the pectin, waxy and P layer, but the tensile strength of henequen irradiated with 10 kGy were maintained. It has been suggested that the use of a 10 kGy dose of electron beam to modify the henequen fiber surface can improve the surface properties and preserve the fibers' mechanical and thermal properties.

  5. CNTF induces dose-dependent alterations in retinal morphology in normal and rcd-1 canine retina.

    Science.gov (United States)

    Zeiss, Caroline J; Allore, Heather G; Towle, Virginia; Tao, Weng

    2006-03-01

    Ciliary neurotrophic factor (CNTF) provides morphologic preservation of rods in several animal models of retinitis pigmentosa (RP). However, CNTF may alter photoreceptor morphology and rod photoreceptor differentiation in vitro, as well as affecting normal retinal electrophysiology. In addition, the capacity of CNTF to support other cell types affected secondarily in RP (cones and ganglion cells) is unclear. The purposes of this study were to examine the effects of CNTF upon a canine model of RP, the rod-cone degeneration (rcd-1) dog. Archival tissue from a previous study assessing the capacity of CNTF to rescue photoreceptors in rcd-1 dogs was used. One eye was treated for 7 weeks before being explanted. The contralateral eye was untreated. A total of 23 rcd-1 dogs and seven control dogs (four untreated and three CNTF-treated) were used. Morphometric data describing outer and inner nuclear layer thickness, inner retinal thickness, cones and ganglion cells were collected at nine evenly spaced points along each retina and analysed using a mixed effects model. Immunohistochemistry was performed on a subset of 11 dogs for expression of rhodopsin, human cone arrestin (hCAR) and recoverin. CNTF protected the outer nuclear layer and increased inner retinal thickness in a dose-dependent manner (both were maximal at CNTF doses of 1-6 ng day-1). Significant cone loss or reduction of inner nuclear layer width in rcd-1 did not occur in this model, therefore we were unable to assess the protective effect of CNTF upon these parameters. CNTF did not afford significant ganglion cell protection. CNTF induced morphologic changes in rods and ganglion cells, as well as reducing expression of hCAR and rhodopsin, but not recoverin. The dose of CNTF which provided optimal outer nuclear layer protection also resulted in several other effects, including altered ganglion cell morphology, increased thickness of the entire retina, and reduced expression of some phototransduction proteins

  6. Multipulse nanosecond laser irradiation of silicon for the investigation of surface morphology and photoelectric properties

    Science.gov (United States)

    Sardar, Maryam; Chen, Jun; Ullah, Zaka; Jelani, Mohsan; Tabassum, Aasma; Cheng, Ju; Sun, Yuxiang; Lu, Jian

    2017-12-01

    We irradiate the single crystal boron-doped silicon (Si) with different number of laser pulses at constant fluence (7.5 J cm-2) in ambient air using Nd:YAG laser and examine its surface morphology and photoelectric properties in details. The results obtained from optical micrographs reveal the increase in heat affected zone (HAZ) and melted area of laser irradiated Si with increasing number of laser pulses. The SEM micrographs evidence the formation of various surface morphologies like laser induced periodic surface structures, crater, microcracks, clusters, cavities, pores, trapped bubbles, nucleation sites, micro-bumps, redeposited material and micro- and nano-particles on the surface of irradiated Si. The surface profilometry analysis informs that the depth of crater is increased with increase in number of incident laser pulses. The spectroscopic ellipsometry reveals that the multipulse irradiation of Si changes its optical properties (refractive index and extinction coefficient). The current-voltage (I-V) characteristic curves of laser irradiated Si show that although the multipulse laser irradiation produces considerable number of surface defects and damages, the electrical properties of Si are well sustained after the multipulse irradiation. The current findings suggest that the multipulse irradiation can be an effective way to tune the optical properties of Si for the fabrication of wide range of optoelectronic devices.

  7. Surface morphology and electronic structure of halogen etched InAs (1 1 1)

    Energy Technology Data Exchange (ETDEWEB)

    Eassa, N., E-mail: nashwa.eassa@nmmu.ac.za [Department of Physics, Nelson Mandela Metropolitan University, P.O. Box 77000, Port Elizabeth 6031 (South Africa); Murape, D.M. [Department of Physics, Nelson Mandela Metropolitan University, P.O. Box 77000, Port Elizabeth 6031 (South Africa); Betz, R. [Department of Chemistry, Nelson Mandela Metropolitan University (South Africa); Neethling, J.H.; Venter, A.; Botha, J.R. [Department of Physics, Nelson Mandela Metropolitan University, P.O. Box 77000, Port Elizabeth 6031 (South Africa)

    2012-05-15

    The reaction of halogen-based etchants with n-InAs (1 1 1)A and the resulting surface morphology and surface electronic structure are investigated using field emission scanning electron microscopy and Raman spectroscopy. Using the intensity ratio of the unscreened longitudinal optical (LO) phonon to the transverse optical (TO) phonon in the Raman spectrum, a significant reduction in band bending is deduced after exposure of the InAs surface to HCl:H{sub 2}O, Br-methanol and I-ethanol for moderate times and concentrations. These procedures also lead to smooth and defect-free InAs surfaces. The improvements in surface properties are reversed, however, if the concentrations of the etchants are increased or the etch time is too long. In the worst cases, pit formation and inverted pyramids with {l_brace}1 1 1{r_brace} side facets are observed. The influence of the etchant concentration and etch time on the morphological and electronic properties of the etched surfaces is reported.

  8. Surface Roughness and Morphology Customization of Additive Manufactured Open Porous Ti6Al4V Structures

    Science.gov (United States)

    Pyka, Grzegorz; Kerckhofs, Greet; Papantoniou, Ioannis; Speirs, Mathew; Schrooten, Jan; Wevers, Martine

    2013-01-01

    Additive manufacturing (AM) is a production method that enables the building of porous structures with a controlled geometry. However, there is a limited control over the final surface of the product. Hence, complementary surface engineering strategies are needed. In this work, design of experiments (DoE) was used to customize post AM surface treatment for 3D selective laser melted Ti6Al4V open porous structures for bone tissue engineering. A two-level three-factor full factorial design was employed to assess the individual and interactive effects of the surface treatment duration and the concentration of the chemical etching solution on the final surface roughness and beam thickness of the treated porous structures. It was observed that the concentration of the surface treatment solution was the most important factor influencing roughness reduction. The designed beam thickness decreased the effectiveness of the surface treatment. In this case study, the optimized processing conditions for AM production and the post-AM surface treatment were defined based on the DoE output and were validated experimentally. This allowed the production of customized 3D porous structures with controlled surface roughness and overall morphological properties, which can assist in more controlled evaluation of the effect of surface roughness on various functional properties. PMID:28788357

  9. Surface Roughness and Morphology Customization of Additive Manufactured Open Porous Ti6Al4V Structures

    Directory of Open Access Journals (Sweden)

    Martine Wevers

    2013-10-01

    Full Text Available Additive manufacturing (AM is a production method that enables the building of porous structures with a controlled geometry. However, there is a limited control over the final surface of the product. Hence, complementary surface engineering strategies are needed. In this work, design of experiments (DoE was used to customize post AM surface treatment for 3D selective laser melted Ti6Al4V open porous structures for bone tissue engineering. A two-level three-factor full factorial design was employed to assess the individual and interactive effects of the surface treatment duration and the concentration of the chemical etching solution on the final surface roughness and beam thickness of the treated porous structures. It was observed that the concentration of the surface treatment solution was the most important factor influencing roughness reduction. The designed beam thickness decreased the effectiveness of the surface treatment. In this case study, the optimized processing conditions for AM production and the post-AM surface treatment were defined based on the DoE output and were validated experimentally. This allowed the production of customized 3D porous structures with controlled surface roughness and overall morphological properties, which can assist in more controlled evaluation of the effect of surface roughness on various functional properties.

  10. Influence of Surface Morphology on the Antimicrobial Effect of Transition Metal Oxides in Polymer Surface.

    Science.gov (United States)

    Oh, Yoo Jin; Hubauer-Brenner, Michael; Hinterdorfer, Peter

    2015-10-01

    In this study, the physical properties of transition metal oxide surfaces were examined using scanning probe microscopic (SPM) techniques for elucidating the antimicrobial activity of molybdenum trioxide (MoO3), tungsten trioxide (WO3), and zinc oxide (ZnO) embedded into the polymers thermoplastic polyurethane (TPU) and polypropylene (PP). We utilized atomic force microscopy (AFM) in the contact imaging mode and its derivative single-pass Kelvin probe force microscopy for investigating samples that were presumably identical in their compositions, but showed different antimicrobial activity in bacterial adhesion tests. Our results revealed that surfaces with larger roughness and higher surface potential variation showed stronger antimicrobial activities compared to smoother and homogeneously charge-distributed surfaces. In addition, capacitance gradient (dC/dZ) measurements were performed to elucidate the antimicrobial activity arising from the different dielectric behavior of the transition metal oxides in this heterogeneous polymer surface. We found that the nano-scale exposure of transition metal oxides on polymer surfaces provided strong antimicrobial effects. Applications arising from our studies will be useful for public and healthcare environments.

  11. Morphological analysis of the left ventricular endocardial surface using a bag-of-features descriptor.

    Science.gov (United States)

    Mukhopadhyay, Anirban; Qian, Zhen; Bhandarkar, Suchendra M; Liu, Tianming; Voros, Szilard; Rinehart, Sarah

    2015-07-01

    The limitations of conventional imaging techniques have hitherto precluded a thorough and formal investigation of the complex morphology of the left ventricular (LV) endocardial surface and its relation to the severity of coronary artery disease (CAD). However, recent developments in high-resolution multirow-detector computed tomography (MDCT) scanner technology have enabled the imaging of the complex LV endocardial surface morphology in a single heartbeat. Analysis of high-resolution computed tomography images from a 320-MDCT scanner allows for the noninvasive study of the relationship between the percent diameter stenosis (DS) values of the major coronary arteries and localization of the cardiac segments affected by coronary arterial stenosis. In this paper, a novel approach for the analysis of the nonrigid LV endocardial surface from MDCT images, using a combination of rigid body transformation-invariant shape descriptors and a more generalized isometry-invariant Bag-of-Features descriptor, is proposed and implemented. The proposed approach is shown to be successful in identifying, localizing, and quantifying the incidence and extent of CAD and, thus, is seen to have a potentially significant clinical impact. Specifically, the association between the incidence and extent of CAD, determined via the percent DS measurements of the major coronary arteries, and the alterations in the endocardial surface morphology is formally quantified. The results of the proposed approach on 16 normal datasets and 16 abnormal datasets exhibiting CAD with varying levels of severity are presented. A multivariable regression test is employed to test the effectiveness of the proposed morphological analysis approach. Experiments performed on a strictly leave-one-out basis are shown to exhibit a distinct and interesting pattern in terms of the correlation coefficient values within the cardiac segments, where the incidence of coronary arterial stenosis is localized.

  12. Morphology-dependent photocatalytic activity of octahedral anatase particles prepared by ultrasonication-hydrothermal reaction of titanates.

    Science.gov (United States)

    Wei, Zhishun; Kowalska, Ewa; Verrett, Jonathan; Colbeau-Justin, Christophe; Remita, Hynd; Ohtani, Bunsho

    2015-08-07

    Octahedral anatase particles (OAPs) were prepared by an ultrasonication (US)-hydrothermal (HT) reaction of partially proton-exchanged potassium titanate nanowires (TNWs). The structural/physical properties of OAP-containing samples, including specific surface area, crystallinity, crystallite size, particle aspect ratio, composition and total OAP content, were analyzed. Photocatalytic activities of samples were measured under irradiation (>290 nm) for oxidative decomposition of acetic acid (CO2 system) and dehydrogenation of methanol (H2 system) under aerobic and deaerated conditions, respectively. Total density of electron traps (ETs) was measured by double-beam photoacoustic spectroscopy (DB-PAS). Mobility and lifetime of charge carriers (electrons) were investigated by the time-resolved microwave conductivity (TRMC) method. The effects of synthesis parameters, i.e., HT duration, HT temperature and US duration, on properties and photocatalytic activities of final products were examined in detail. The sample prepared with 1 h US duration and 6 h HT duration at 433 K using 267 mg of TNWs in 80 mL of Milli-Q water exhibited the highest photocatalytic activity. It was found that change in HT duration or HT temperature while keeping the other conditions the same resulted in changes in all properties and photocatalytic activity. On the other hand, duration of US treatment, before HT reaction, influenced the morphology of both the reagent (by TNWs breaking) and final products (change in total OAP content); samples prepared with various US durations exhibited almost the same structural/physical properties evaluated in this study but were different in morphology and photocatalytic activity. This enabled clarification of the correlation between morphology and photocatalytic activity, i.e., the higher the total OAP content was, the higher was the level of photocatalytic activity, especially in the CO2 system. Although the decay after maximum TRMC signal intensity (Imax) was

  13. Superhydrophobic Surfaces Developed by Mimicking Hierarchical Surface Morphology of Lotus Leaf

    Directory of Open Access Journals (Sweden)

    Sanjay S. Latthe

    2014-04-01

    Full Text Available The lotus plant is recognized as a ‘King plant’ among all the natural water repellent plants due to its excellent non-wettability. The superhydrophobic surfaces exhibiting the famous ‘Lotus Effect’, along with extremely high water contact angle (>150° and low sliding angle (<10°, have been broadly investigated and extensively applied on variety of substrates for potential self-cleaning and anti-corrosive applications. Since 1997, especially after the exploration of the surface micro/nanostructure and chemical composition of the lotus leaves by the two German botanists Barthlott and Neinhuis, many kinds of superhydrophobic surfaces mimicking the lotus leaf-like structure have been widely reported in the literature. This review article briefly describes the different wetting properties of the natural superhydrophobic lotus leaves and also provides a comprehensive state-of-the-art discussion on the extensive research carried out in the field of artificial superhydrophobic surfaces which are developed by mimicking the lotus leaf-like dual scale micro/nanostructure. This review article could be beneficial for both novice researchers in this area as well as the scientists who are currently working on non-wettable, superhydrophobic surfaces.

  14. Biofilm formation and Candida albicans morphology on the surface of denture base materials.

    Science.gov (United States)

    Susewind, Sabine; Lang, Reinhold; Hahnel, Sebastian

    2015-12-01

    Fungal biofilms may contribute to the occurrence of denture stomatitis. The objective of the study was to investigate the biofilm formation and morphology of Candida albicans in biofilms on the surface of denture base materials. Specimens were prepared from different denture base materials. After determination of surface properties and salivary pellicle formation, mono- and multispecies biofilm formation including Candida albicans ATCC 10231 was initiated. Relative amounts of adherent cells were determined after 20, 44, 68 and 188 h; C. albicans morphology was analysed employing selective fluorescence microscopic analysis. Significant differences were identified in the relative amount of cells adherent to the denture base materials. Highest blastospore/hyphae index suggesting an increased percentage of hyphae was observed in mono- and multispecies biofilms on the soft denture liner, which did not necessarily respond to the highest relative amount of adherent cells. For both biofilm models, lowest relative amount of adherent cells was identified on the methacrylate-based denture base material, which did not necessarily relate to a significantly lower blastospore/hyphae index. The results indicate that there are significant differences in both biofilm formation as well as the morphology of C. albicans cells in biofilms on the surface of different denture base materials. © 2015 Blackwell Verlag GmbH.

  15. Effect of interface on surface morphology and proton conduction of polymer electrolyte thin films.

    Science.gov (United States)

    Ohira, Akihiro; Kuroda, Seiichi; Mohamed, Hamdy F M; Tavernier, Bruno

    2013-07-21

    To understand the relationship between surface morphology and proton conduction of polymer electrolyte thin films, perfluorinated ionomer Nafion® thin films were prepared on different substrates such as glassy carbon (GC), hydrophilic-GC (H-GC), and platinum (Pt) as models for the ionomer film within a catalyst layer. Atomic force microscopy coupled with an electrochemical (e-AFM) technique revealed that proton conduction decreased with film thickness; an abrupt decrease in proton conductance was observed when the film thickness was less than ca. 10 nm on GC substrates in addition to a significant change in surface morphology. Furthermore, thin films prepared on H-GC substrates with UV-ozone treatment exhibited higher proton conduction than those on untreated GC substrates. However, Pt substrates exhibited proton conduction comparable to that of GCs for films thicker than 20 nm; a decrease in proton conduction was observed at ∼5 nm thick film but was still much higher than for carbon substrates. These results indicate that the number of active proton-conductive pathways and/or the connectivity of the proton path network changed with film thickness. The surface morphology of thinner films was significantly affected by the film/substrate interface and was fundamentally different from that of the bulk thick membrane.

  16. Swelling-induced morphology reconstruction in block copolymer nanorods: kinetics and impact of surface tension during solvent evaporation.

    Science.gov (United States)

    Wang, Yong; Tong, Ling; Steinhart, Martin

    2011-03-22

    Nanoscopic domain structures of BCP nanorods can be converted into well-defined mesopore systems by swelling the BCP minority component with a selective solvent at temperatures below the bulk glass transition temperature of the nonswelling matrix. The initial stage of this process involves rapid morphology reconstruction of the nonswelling majority domains to accommodate the increased volume of the swelling minority domains caused by rapid solvent uptake. Morphology reconstruction slows down once entropic restoring forces of the swelling chains impede further uptake of swelling agent. Upon evaporation of the swelling agent, mesopores form in place of the swollen domains as the swollen minority blocks undergo entropic relaxation while intermediate nonequilibrium morphologies in the BCP nanorods are fixated by the reconstructed majority component. The surface area of mesopores developing when swollen cylindrical minority domains collapse may be minimized by the growth of Rayleigh instabilities. Depending on swelling temperature, swelling agent, and BCP architecture, BCP nanorods with one or several cylindrical channels undulated or uniform in diameter running along their long axes, linear strings of spherical cavities, and continuous mesopore systems can be obtained.

  17. Superhydrophobic Polyimide via Ultraviolet Photooxidation: The Evolution of Surface Morphology and Hydrophobicity under Different Ultraviolet Intensities

    Directory of Open Access Journals (Sweden)

    Hongyu Gu

    2015-01-01

    Full Text Available Ultraviolet (UV photooxidation has recently been developed to fabricate superhydrophobic polyimide (PI films in combination with fluoroalkylsilane modification. However, it remains unclear whether the surface morphology and hydrophobicity are sensitive to technical parameters such as UV intensity and radiation environment. Herein, we focus on the effects of UV intensity on PI surface structure and wettability to gain comprehensive understanding and more effective control of this technology. Scanning electron microscopy (SEM and atomic force microscopy (AFM results showed that UV intensity governed the evolutionary pattern of surface morphology: lower UV intensity (5 mW/cm2 facilitated in-plane expansion of dendritic protrusions while stronger UV (10 and 15 mW/cm2 encouraged localized growth of protrusions in a piling-up manner. Surface roughness and hydrophobicity maximized at the intensity of 10 mW/cm2, as a consequence of the slowed horizontal expansion and preferred vertical growth of the protrusions when UV intensity increased. Based on these results, the mechanism that surface micro/nanostructures developed in distinct ways when exposed to different UV intensities was proposed. Though superhydrophobicity (water contact angle larger than 150° can be achieved at UV intensity not less than 10 mW/cm2, higher intensity decreased the effectiveness. Therefore, the UV photooxidation under 10 mW/cm2 for 72 h is recommended to fabricate superhydrophobic PI films.

  18. Coevolution of bed surface patchiness and channel morphology: 2. Numerical experiments

    Science.gov (United States)

    Nelson, Peter A.; McDonald, Richard R.; Nelson, Jonathan M.; Dietrich, William E.

    2015-01-01

    In gravel bed rivers, bed topography and the bed surface grain size distribution evolve simultaneously, but it is not clear how feedbacks between topography and grain sorting affect channel morphology. In this, the second of a pair of papers examining interactions between bed topography and bed surface sorting in gravel bed rivers, we use a two-dimensional morphodynamic model to perform numerical experiments designed to explore the coevolution of both free and forced bars and bed surface patches. Model runs were carried out on a computational grid simulating a 200 m long, 2.75 m wide, straight, rectangular channel, with an initially flat bed at a slope of 0.0137. Over five numerical experiments, we varied (a) whether an obstruction was present, (b) whether the sediment was a gravel mixture or a single size, and (c) whether the bed surface grain size feeds back on the hydraulic roughness field. Experiments with channel obstructions developed a train of alternate bars that became stationary and were connected to the obstruction. Freely migrating alternate bars formed in the experiments without channel obstructions. Simulations incorporating roughness feedbacks between the bed surface and flow field produced flatter, broader, and longer bars than simulations using constant roughness or uniform sediment. Our findings suggest that patches are not simply a by-product of bed topography, but they interact with the evolving bed and influence morphologic evolution.

  19. Effects of erosive challenge on the morphology and surface properties of luting cements

    Directory of Open Access Journals (Sweden)

    Brenna Louise Cavalcanti GONDIM

    Full Text Available Abstract Introduction Few studies investigated the surface properties of luting cements after erosive challenge. Objective To evaluate the surface roughness (Ra, Vickers hardness (VHN and morphology of 4 luting cements after erosive challenge. Material and method Twenty specimens of each cement were prepared (4×2mm and divided into experimental (erosive challenge and control (artificial saliva groups (n=10: Rely X U200 (U200; Rely X ARC (ARC; Ketac Cem Easy Mix (Ketac and Zinc phosphate (ZnP. The erosive challenge was performed by four daily erosive cycles (90s in a cola drink and 2 h in artificial saliva over 7 days. Ra and VHN readings were performed before and after erosion. The percentage of hardness loss (%VHN was obtained after erosion. The surface morphology was analyzed by scanning electron microscopy (SEM. ANOVA, Tukey and Student-T tests were used (α=0.05. Result After erosion, all luting cements had increase in Ra values and U200 and ZnP groups had the highest %VHN. After saliva immersion, only U200 and ZnP groups had significant increases in Ra values and there were no significant differences among the groups in %VHN. SEM analysis showed that Ketac and ZnP groups had rough and porous surfaces, and U200 group had higher resin matrix degradation than ARC group. Conclusion Erosive challenge with a cola drink affected the surface properties of all luting cements.

  20. The surface morphology of retinal breaks and lattice retinal degeneration. A scanning electron microscopic study.

    Science.gov (United States)

    Robinson, M R; Streeten, B W

    1986-02-01

    In 14 of 110 eye bank eyes, lesions characteristic of peripheral retinal surface pathology were examined by scanning electron microscopy (SEM). These included operculated and flap tears, trophic round holes, lattice degeneration with holes, and paravascular retinal "pitting" degeneration. By SEM, the edges of the retinal breaks were covered by smooth cellular membranes, merging peripherally with a meshwork of vitreous fibrils. The membrane cells had poorly defined borders, a pitted surface, and variable numbers of microvilli consistent with glia. Lattice surfaces and foci of paravascular retinal degeneration were covered by similar membrane, but showed characteristic differences. It appears that breaks in the internal limiting membrane always stimulate proliferation of preretinal glial membranes. Similar cellular morphology of the membranes associated with breaks is consistent with a common cell of origin. Limited proliferation of these membranes suggests that surface gliosis is normally inhibited when the cells contact either intact basement membrane or vitreous.

  1. Surface Morphology and Overlayer Formation Kinetics of OXYGEN/SILVER(110) Studied by Scanning Tunneling Microscopy

    Science.gov (United States)

    Pai, Woei Wu.

    1995-01-01

    I have applied scanning tunneling microscopy (STM) to study clean and oxygen-covered vicinal Ag(110) surfaces at room temperature. Experimental results of surface morphology/stability, surface mass transport and surface chemical reactivity are presented. On clean vicinal Ag(110) surfaces, the steps distribute under the influence of step-step interactions. The terrace width distributions indicate an additional oscillatory component besides an l^{-2} interaction term. If the surface is contaminated slightly (quasi-clean), isolated "pinning sites" impede the motion of steps. The interactions between steps push the steps across the pinning site, resulting in a curved step front. When oxygen atoms adsorb on stepped Ag(110), a dramatic change in surface morphology occurs. The surface separates into two distinct phases--step bunches and large terraces (facets). The orientational instability is closely related to the linear "added-row" structure of the oxygen overlayer, as the long O chains push steps into bunches. The O chains do not push the steps effectively when O chains orient perpendicular to steps, and the faceting proceeds through nucleation. If the O chains orient near parallel to steps, however, O chains push the steps easily and the faceting proceeds through spinodal decomposition. To understand the mass transport during faceting, I quantify the thermal step fluctuations by employing a Langevin statistical analysis. The mass transport mechanism at the step edge is shown to be by atomic exchange between steps and terraces, making the step an effective source or sink for Ag adatoms. This Ag source also proves essential in O overlayer formation, since both Ag and O atoms are incorporated into the "added -row" overlayer structure. Because an Ag source must be found during the adlayer formation, I show the surface morphology is sensitive to oxygen dosing pressure. Above a critical O pressure of 10^{-5} mbar, vacancy islands on terraces provide a second source of Ag

  2. Chemical analysis and surface morphology of enamel following ozone application with different concentrations and exposure times

    Directory of Open Access Journals (Sweden)

    Iman I. Elsayad

    2011-04-01

    Full Text Available This study aimed to determine the effect of different ozone concentrations applied with different exposure times on the chemical composition and the surface morphology of enamel. Twenty human mandibular molars were divided into four groups according to ozone concentration and exposure times. Group A received 90 μg of ozone/ml oxygen for 1 min, group B received 90 μg of ozone/ml oxygen for 2 min, group C received 120 μg of ozone/ml oxygen for 1 min and group D received 120 μg of ozone/ml oxygen for 2 min. The ozone source was from a medical ozone generator equipped with a device to adjust the concentration. Buccal surfaces of teeth were tested before and after ozone application so that each tooth served as a control for itself, using Environmental Scanning Electron Microscope (ESEM connected to an Electron Dispersive Analytical X-ray (EDAX. Changes in calcium and phosphorus percentage levels were recorded and the Ca/P ratio was calculated. The values were statistically analyzed using the one-way ANOVA test with a level of significance set at P ⩽ 0.05. No statistical significant difference was found between the control and the tested groups in minerals content or ratio as P > 0.05. ESEM images showed enamel surface roughness with 2 min ozone exposure times. High ozone concentration with prolonged exposure time does not change the chemical composition of enamel. Applying ozone for 2 min alters the surface morphology of enamel causing variable degrees of roughness. Using high ozone concentrations with prolonged exposure times for caries reversal or prevention and for bleaching may be contraindicated if this changes the surface morphology of enamel.

  3. Morphological correlates of corticosteroid-induced changes in prefrontal cortex-dependent behaviors.

    Science.gov (United States)

    Cerqueira, João J; Pêgo, José M; Taipa, Ricardo; Bessa, João M; Almeida, Osborne F X; Sousa, Nuno

    2005-08-24

    Imbalances in the corticosteroid milieu have been implicated in several neuropsychiatric disorders, including depression and schizophrenia. Prefrontal cortex (PFC) dysfunction is also a hallmark of these conditions, causing impairments in executive functions such as behavioral flexibility and working memory. Recent studies have suggested that the PFC might be influenced by corticosteroids released during stress. To test this possibility, we assessed spatial working memory and behavioral flexibility in rats submitted to chronic adrenalectomy or treatment with corticosterone (25 mg/kg) or the synthetic glucocorticoid dexamethasone (300 microg/kg); the behavioral analysis was complemented by stereological evaluation of the PFC (prelimbic, infralimbic, and anterior cingulate regions), the adjacent retrosplenial and motor cortices, and the hippocampal formation. Dexamethasone treatment resulted in a pronounced impairment in working memory and behavioral flexibility, effects that correlated with neuronal loss and atrophy of layer II of the infralimbic, prelimbic, and cingulate cortices. Exposure to corticosterone produced milder impairments in behavioral flexibility, but not in working memory, and reduced the volume of layer II of all prefrontal areas. Interestingly, adrenalectomy-induced deleterious effects only became apparent on the reverse learning task and were not associated with structural alterations in the PFC. None of the experimental procedures influenced the morphology of retrosplenial or motor cortices, but stereological measurements confirmed previously observed effects of corticosteroids on hippocampal structure. Our results describe, for the first time, that imbalances in the corticosteroid environment can induce degeneration of specific layers of the PFC; these changes appear to be the morphological correlate of corticosteroid-induced impairment of PFC-dependent behavior(s).

  4. Dependence of electrical properties of polypropylene isomers on morphology and chain conformation

    Energy Technology Data Exchange (ETDEWEB)

    Guadagno, Liberata; Raimondo, Marialuigia; Vittoria, Vittoria [Dipartimento di Ingegneria Chimica e Alimentare, Universita di Salerno, Via Ponte Don Melillo, 84084 Fisciano (Italy); Bartolomeo, Antonio Di [Dipartimento di Fisica ' E Caianiello' , Via S Allende, 84081 Baronissi (Italy); De Vivo, Biagio; Lamberti, Patrizia; Tucci, Vincenzo, E-mail: lguadagno@unisa.i [Dipartimento di Ingegneria dell' Informazione e Ingegneria Elettrica Universita di Salerno, Via Ponte Don Melillo, 84084 Fisciano (Saudi Arabia) (Italy)

    2009-07-07

    The electrical properties of polypropylene isomers were correlated with the morphology and chain conformation of differently obtained isotactic (iPP) and syndiotactic (sPP) samples. In the case of iPP, a crystallized and a smectic sample were prepared, whereas for sPP two crystalline helical samples and a mesophase with the chains in trans-planar conformation were considered. The phase composition was obtained for all the samples comparing x-ray diffractograms and transport properties of vapours, which give the crystallinity and the amorphous fraction, respectively. The fraction of mesophase was obtained by the difference of the previous values. The study of the morphology evidenced similarities and differences among the samples, which were discussed and correlated with the phase composition. The electrical conductivity was measured for all the samples, and the syndiotactic isomer showed the lowest value as well as a dependence on the structure. In contrast, the isotactic isomer showed the same behaviour for either polymorph. Based on the structural and electrical results, a phenomenological explanation of the conduction mechanisms taking place in the different forms has been proposed. In particular, the current in the iPP seems to be controlled by Schottky emission, i.e. by field-assisted thermo-ionic injection of carriers from the electrode into the polymer, whereas for the sPP more than one mechanism is likely to be effective, although the ionic transport appears as the predominant one. The experimental data confirm a different behaviour of the ionic conduction properties for the different polymorphs, highlighting the greater insulating characteristics of the mesomorphic structure of the syndiotactic isomer.

  5. Influence of surface remodelling using burs on the macro and micro surface morphology of anatomically formed fibre posts.

    Science.gov (United States)

    Plotino, G; Grande, N M; Pameijer, C H; Somma, F

    2008-04-01

    To evaluate the effect of modifying preformed fibre-reinforced composite (FRC) endodontic posts on their surface morphology and to determine how this procedure affects the integrity of the posts. Surfaces of 10 preformed glass-fibre posts (group 1) and carbon-fibre posts (group 2) were compared with those of individually formed glass-fibre posts (group 3). Ten FRC posts were modelled in order to give them a shape as close as possible to the anatomy of oval root canals. Starting from a preformed cylindrical fibre post 2.5 mm in diameter, it was modelled in such a way as to passively occupy the entire post-space length, using a cast previously created as a guide. Microscopic analyses (optical stereomicroscope and scanning electron microscope) of the post surfaces revealed similar features in all three groups. All posts had regular surfaces after cutting with a diamond bur. Smear layer mainly attributable to the cutting procedures covered the cut surface of some specimens. In conclusion, modulation of a fibre post using a diamond-coated bur did not show a loss of integrity of the post. *Because of the importance of micromechanical retention, the surface integrity of fibre posts may be important for adhesion between post and composite resin. *Modification of a fibre post using a diamond-coated bur did not damage the surface integrity of the posts. *Fibre posts can be ground to a different shape without losing their surface integrity, resulting in posts with a surface that is not visibly different from unmodified commercially available fibre posts.

  6. Annealing assisted structural and surface morphological changes in Langmuir–Blodgett films of nickel octabutoxy phthalocyanine

    Energy Technology Data Exchange (ETDEWEB)

    Shilpa Harish, T.; Viswanath, P., E-mail: viswanath@cnsms.res.in

    2016-01-01

    We report our studies on thin films of metallo-phthalocyanine (MPc), Nickel(II)1,4,8,11,15,18,22,25-octabutoxy-29H,31H-phthalocyanine (NiPc(OBu){sub 8}) transferred in a well defined thermodynamic state over a self assembled monolayer (octadecyl trichlorosilane)/SiO{sub 2}/Si substrate using the Langmuir–Blodgett (LB) method. The films are characterized using differential scanning calorimetry (DSC), grazing incidence X-ray diffraction (GIXD) and atomic force microscopy (AFM) techniques. DSC studies on powdered samples in the bulk indicate enantiotropic solid–solid phase transition. GIXD studies on the as-deposited LB film show a Bragg peak indicating crystallinity of the thin film. Annealing (373 K) results in reduction of lattice spacing (1.21 Å) signifying changes in molecular packing within the unit cell. At this stage, an additional Bragg peak is observed which grows at the expense of the former one and they coexist between 373 K and 423 K. A discontinuity in lattice spacing from 20.73 to 15.12 Å with annealing indicates clearly a structural change of the underlying crystalline lattice. Correspondingly, the surface morphology images obtained using AFM show, with annealing, a transformation from spherical granular morphology to elongated, flat crystallites suggesting asymmetric growth process. Statistical parameters of the grain extracted from the AFM images show that the size, fractal dimension and circularity are affected by annealing. Based on these studies, we infer the structural and surface morphological changes of the meta-stable phase (Form I) to the stable phase (Form II) in annealed LB films of phthalocyanine. - Highlights: • Langmuir–Blodgett (LB) films of phthalocyanine subjected to thermal annealing. • Structural transformation and coexistence of polymorphs in LB films • Surface morphology changes from nanoscale grains to elongated crystallites. • Reduction of fractal dimension and circularity index reveals asymmetric growth.

  7. Variability of Surface Reflection Amplitudes of GPR Horn Antenna Depending on Distance between Antenna and Surface

    Directory of Open Access Journals (Sweden)

    Komačka Jozef

    2016-05-01

    Full Text Available The study focused on variability of surface reflections amplitudes of GPR horn antenna in relation to distance between an antenna and a surface is presented in the paper. The air-coupled antenna with the central frequency of 1 GHz was used in the investigation. Four types of surfaces (dry pavement, wet pavement, metal plate and composite layer from gypsum and wood were tested. The distance of antenna above the surfaces was changed in the range from 37.5 cm to 53.5 cm. The amplitudes of negative and positive peaks and their variability were analysed in relation to the distance of antenna above the surfaces. Moreover, the influence of changes in the peaks of negative and positive amplitudes on the total amplitudes was assessed. It was found out the amplitudes of negative peaks for all investigated surfaces were relatively consistent in the range from 40.5 cm to 48.5 cm and the moderate decline was identified in the case of amplitudes of positive peaks in the range of distances from 37.5 cm to 51.5 cm. This decline influences the tendency of total amplitudes. Based on the results of analysis it can be stated the distance of air-coupled antenna above the surface can influence the value of total amplitude and the differences depend on the type of surface.

  8. In-situ spectroscopic erosion yield measurement with applications to sputtering and surface morphology alterations

    International Nuclear Information System (INIS)

    Leung, W.K.; Hirooka, Y.; Conn, R.W.; Goebel, D.M.; Labombard, B.; Nygren, R.

    1988-01-01

    An in-situ spectroscopic erosion yield measurement is developed and used to monitor material surface erosion during bombardment by a plasma. The experiments are performed in a plasma that has the characteristics of a fusion tokamak boundary plasma but the technique is applicable to many processes where plasma erosion is important. Erosion yield of materials bombarded in a high flux (up to 10 18 ion/cm 2 /s) plasma environment has been previously studies using weight loss measurements. In the present study, the sputtered flux from a material is monitored by the line emission intensities of atoms eroded from the surface. The line intensities can be used to infer erosion yields after proper calibration. The method agrees well with results from weight loss measurements. Earlier work established that the material surface structure can substantially influence the erosion yield. When a change of surface morphology (e.g., cone formation) occurs, weight loss methods cannot be used to determine the erosion yield. However, the in-situ erosion measurement is suitable and is used to investigate the relation between the on-set of morphology changes and alternations in erosion yield during plasma bombardment. Experiments are reported for copper, as an example of a pure material, and stainless steel, as an example of an alloy system. The formation of surface cones is observed only when both the sample temperature is above a critical value and surface impurities exist. If the source of impurities is removed, or the sample temperature is lowered below the critical value, a surface rough with cones will be returned to a smooth state

  9. An in-situ spectroscopic erosion yield measurement with applications to sputtering and surface morphology alterations

    International Nuclear Information System (INIS)

    Leung, W.K.; Hirooka, Y.; Conn, R.W.; Goebel, D.M.; LaBombard, B.; Nygren, R.

    1988-07-01

    An in-situ spectroscopic erosion yield measurement is developed and used to monitor material surface erosion during bombardment by a plasma. The experiments are performed in a plasma that has the characteristics of a fusion tokamak boundary plasma but the technique is applicable to many processes where plasma erosion is important. Erosion yield of materials bombarded in a high flux (up to 10 18 ion/cm 2 /s) plasma environment has been previously studied using weight loss measurements. In the present study, the sputtered flux from a material is monitored by the line emission intensities of atoms eroded from the surface. The line intensities can be used to infer erosion yields after proper calibration. The method agrees well with results from weight loss measurements. Earlier work established that the material surface structure can substantially influence the erosion yield. When a change of surface morphology (e.g. cone formation) occurs, weight loss methods cannot be used to determine the erosion yield. However, the in-situ erosion measurement is suitable and is used to investigate the relation between the on-set of morphology changes and alternations in erosion yield during plasma bombardment. Experiments are reported for copper, as an example of pure material, and stainless steel, as a example of an alloy system. The formation of surface cones is observed only when both the sample temperature is above a critical value and surface impurities exist. If the source of impurities is removed, or the sample temperature is lowered below the critical values, a surface rough with cones will be returned to smooth state. 20 refs., 10 figs

  10. In situ spectroscopic erosion yield measurement with applications to sputtering and surface morphology alterations

    International Nuclear Information System (INIS)

    Leung, W.K.; Hirooka, Y.; Conn, R.W.; Goebel, D.M.; Labombard, B.; Nygren, R.

    1989-01-01

    An in situ spectroscopic erosion yield measurement is developed and used to monitor material surface erosion during bombardment by a plasma. The experiments are performed in a plasma that has the characteristics of a fusion tokamak boundary plasma but the technique is applicable to many processes where plasma erosion is important. Erosion yield of materials bombarded in a high flux (up to 10 18 ion/cm 2 s) plasma environment has been previously studied using weight loss measurements. In the present study, the sputtered flux from a material is monitored by the line emission intensities of atoms eroded from the surface. The line intensities can be used to infer erosion yields after proper calibration. The method agrees well with results from weight loss measurements. Earlier work established that the material surface structure can substantially influence the erosion yield. When a change of surface morphology (e.g., cone formation) occurs, weight loss methods cannot be used to determine the erosion yield. However, the in situ erosion measurement is suitable and is used to investigate the relation between the onset of morphology changes and alternations in erosion yield during plasma bombardment. Experiments are reported for copper, as an example of a pure material, and stainless steel, as an example of an alloy system. The formation of surface cones is observed only when both the sample temperature is above a critical value and surface impurities exist. If the source of impurities is removed, or the sample temperature is lowered below the critical value, a surface rough with cones will be returned to a smooth state

  11. Morphology and Differentiation of MG63 Osteoblast Cells on Saliva Contaminated Implant Surfaces

    Directory of Open Access Journals (Sweden)

    Neda Shams

    2015-11-01

    Full Text Available Objectives: Osteoblasts are the most important cells in the osseointegration process. Despite years of study on dental Implants, limited studies have discussed the effect of saliva on the adhesion process of osteoblasts to implant surfaces. The aim of this in vitro study was to evaluate the effect of saliva on morphology and differentiation of osteoblasts attached to implant surfaces.Materials and Methods: Twelve Axiom dental implants were divided into two groups. Implants of the case group were placed in containers, containing saliva, for 40 minutes. Then, all the implants were separately stored in a medium containing MG63 human osteoblasts for a week. Cell morphology and differentiation were assessed using a scanning electron microscope and their alkaline phosphatase (ALP activity was determined. The t-test was used to compare the two groups.Results: Scanning electron microscopic observation of osteoblasts revealed round or square cells with fewer and shorter cellular processes in saliva contaminated samples, whereas elongated, fusiform and well-defined cell processes were seen in the control group. ALP level was significantly lower in case compared to control group (P<0.05.Conclusion: Saliva contamination alters osteoblast morphology and differentiation and may subsequently interfere with successful osseointegration. Thus, saliva contamination of bone and implant must be prevented or minimized.

  12. Three-dimensional shape variation of talar surface morphology in hominoid primates.

    Science.gov (United States)

    Parr, W C H; Soligo, C; Smaers, J; Chatterjee, H J; Ruto, A; Cornish, L; Wroe, S

    2014-07-01

    The hominoid foot is of particular interest to biological anthropologists, as changes in its anatomy through time reflect the adoption of terrestrial locomotion, particularly in species of Australopithecus and Homo. Understanding the osteological morphology associated with changes in whole foot function and the development of the plantar medial longitudinal foot arch are key to understanding the transition through habitual bipedalism in australopithecines to obligate bipedalism and long-distance running in Homo. The talus is ideal for studying relationships between morphology and function in this context, as it is a major contributor to the adduction-abduction, plantar-dorsal flexion and inversion-eversion of the foot, and transmits all forces encountered from the foot to the leg. The talar surface is predominantly covered by articular facets, which have different quantifiable morphological characters, including surface area, surface curvature and orientation. The talus also presents challenges to the investigator, as its globular shape is very difficult to quantify accurately and reproducibly. Here we apply a three-dimensional approach using type 3 landmarks (slid semilandmarks) that are geometrically homologous to determine overall talar shape variations in a range of living and fossil hominoid taxa. Additionally, we use novel approaches to quantify the relative orientations and curvatures of talar articular facets by determining the principal vectors of facet orientation and fitting spheres to articular facets. The resulting metrics are analysed using phylogenetic regressions and principal components analyses. Our results suggest that articular surface curvatures reflect locomotor specialisations with, in particular, orangutans having more highly curved facets in all but the calcaneal facet. Similarly, our approach to quantifying articular facet orientation appears to be effective in discriminating between extant hominoid species, and may therefore provide a

  13. The nucleus of Comet Borrelly: A study of morphology and surface brightness

    Science.gov (United States)

    Oberst, J.; Howington-Kraus, E.; Kirk, R.; Soderblom, L.; Buratti, B.; Hicks, M.; Nelson, R.; Britt, D.

    2004-01-01

    Stereo images obtained during the DS1 flyby were analyzed to derive a topographic model for the nucleus of Comet 19P/Borrelly for morphologic and photometric studies. The elongated nucleus has an overall concave shape, resembling a peanut, with the lower end tilted towards the camera. The bimodal character of surface-slopes and curvatures support the idea that the nucleus is a gravitational aggregate, consisting of two fragments in contact. Our photometric modeling suggests that topographic shading effects on Borrelly's surface are very minor (the given resolution of the terrain model. Instead, albedo effects are thought to dominate Borrelly's large variations in surface brightness. With 90% of the visible surface having single scattering albedos between 0.008 and 0.024, Borrelly is confirmed to be among the darkest of the known Solar System objects. Photometrically corrected images emphasize that the nucleus has distinct, contiguous terrains covered with either bright or dark, smooth or mottled materials. Also, mapping of the changes in surface brightness with phase angle suggests that terrain roughness at subpixel scale is not uniform over the nucleus. High surface roughness is noted in particular near the transition between the upper and lower end of the nucleus, as well as near the presumed source region of Borrelly's main jets. Borrelly's surface is complex and characterized by distinct types of materials that have different compositional and/or physical properties. ?? 2003 Elsevier Inc. All rights reserved.

  14. Measurement of the surface morphology of plasma facing components on the EAST tokamak by a laser speckle interferometry approach

    Science.gov (United States)

    Hongbei, WANG; Xiaoqian, CUI; Yuanbo, LI; Mengge, ZHAO; Shuhua, LI; Guangnan, LUO; Hongbin, DING

    2018-03-01

    The laser speckle interferometry approach provides the possibility of an in situ optical non-contacted measurement for the surface morphology of plasma facing components (PFCs), and the reconstruction image of the PFC surface morphology is computed by a numerical model based on a phase unwrapping algorithm. A remote speckle interferometry measurement at a distance of three meters for real divertor tiles retired from EAST was carried out in the laboratory to simulate a real detection condition on EAST. The preliminary surface morphology of the divertor tiles was well reproduced by the reconstructed geometric image. The feasibility and reliability of this approach for the real-time measurement of PFCs have been demonstrated.

  15. Effect of annealing on the growth dynamics of ZnPc LB thin film and its surface morphology

    Energy Technology Data Exchange (ETDEWEB)

    Roy, Dhrubojyoti, E-mail: dhrubojyoti27@gmail.com; Das, Nayan Mani; Gupta, P. S. [Nanoscience and Thin Film Laboratory, Department of Applied Physics, Indian School of Mines, Dhanbad 826004, India. (India)

    2014-07-15

    The ZnPc molecules in the thin film prepared by Langmuir-Blodgett (LB) process in asdeposited state has been found to have an edge on orientation with average tilt angle of 64.3 ° as confirmed from the Pressure-Area (π-A) isotherm and X-ray diffraction (XRD) study. The ZnPc LB thin film has been observed to have abnormal growth mode at higher annealing temperature and it is mainly driven by minimization of surface free energy which lead to large increase in crystallinity of the film. Kinetically favored orientational and structural transitions of ZnPc thin film during annealing and their effect on the surface morphology of the thin film has been studied using scaling concepts. The scaling exponents 1) root mean square (RMS) roughness σ, 2) roughness exponent α and, 3) in plane correlation length ξ are calculated from the HDCF g(r) and ACF C(r). The RMS surface roughness σ is found to be dependent on the as defined short wavelength undulations (ρ) and long wavelength undulations (χ). Both ρ and χ are the function of all the three scaling exponents. σ has been observed to be maximum for the ZnPc thin film annealed at 290 °C, since the χ shoot to maximum value at this temperature due to the formation of small domains of ZnPc nanorods. The self affinity of the ZnPc thin film is found to decrease on annealing as obtained from both power spectral density (PSD) and HDCF g(R) and ACF C(R) study, which confirms that the dimension of surface morphology of the ZnPc LB thin film transform towards 2D with increase in annealing temperature.

  16. Effect of annealing on the growth dynamics of ZnPc LB thin film and its surface morphology

    Directory of Open Access Journals (Sweden)

    Dhrubojyoti Roy

    2014-07-01

    Full Text Available The ZnPc molecules in the thin film prepared by Langmuir-Blodgett (LB process in asdeposited state has been found to have an edge on orientation with average tilt angle of 64.3 ° as confirmed from the Pressure-Area (π-A isotherm and X-ray diffraction (XRD study. The ZnPc LB thin film has been observed to have abnormal growth mode at higher annealing temperature and it is mainly driven by minimization of surface free energy which lead to large increase in crystallinity of the film. Kinetically favored orientational and structural transitions of ZnPc thin film during annealing and their effect on the surface morphology of the thin film has been studied using scaling concepts. The scaling exponents 1 root mean square (RMS roughness σ, 2 roughness exponent α and, 3 in plane correlation length ξ are calculated from the HDCF g(r and ACF C(r. The RMS surface roughness σ is found to be dependent on the as defined short wavelength undulations (ρ and long wavelength undulations (χ. Both ρ and χ are the function of all the three scaling exponents. σ has been observed to be maximum for the ZnPc thin film annealed at 290 °C, since the χ shoot to maximum value at this temperature due to the formation of small domains of ZnPc nanorods. The self affinity of the ZnPc thin film is found to decrease on annealing as obtained from both power spectral density (PSD and HDCF g(R & ACF C(R study, which confirms that the dimension of surface morphology of the ZnPc LB thin film transform towards 2D with increase in annealing temperature.

  17. Morphological Specifications of the Bird Schistosome Cercariae and Surface Carbohydrates as Receptors for Lectins

    Directory of Open Access Journals (Sweden)

    I Moebedi

    2007-04-01

    Full Text Available Background: To determine the morphological specifications of the bird schistosomes cercaria from Lymnaea gedrosiana and to detect the surface carbohydrates as receptors for host lectins in the host-parasite relationship systems such as avian schistosomiasis and human cercarial dermatitis. Methods: One hundred ninety two snails collected from Dezful areas in Khuzestan Province, in the south west of Iran, during 2005-2006 were examined for cercariae using shedding and crushing methods. In addition, surface carbohydrates on the cercariae were detected by lentil (Lens culinaris lectins. Results: From the total number of Lymnaea gedrosiana, which examined for bird schistosomes cercaria, 9(4% snails were found to be infected with furcocercus cercaria of the bird schistosomes (probably Gigantobilharzia sp.. Mannose monosaccharide CH2OH (CHOH4CHO as surface carbohydrate was also detected on the cercariae. Conclusion: Mannose carbohydrate on these cercariae may be used as receptor by lectins.

  18. The Relationship Between the Surface Morphology and Chemical Composition of Gunshot Residue Particles.

    Science.gov (United States)

    Kara, Ilker; Lisesivdin, Sefer Bora; Kasap, Mehmet; Er, Elif; Uzek, Ugur

    2015-07-01

    In this study, chemical composition and morphology of gunshot residue (GSR) of 9 × 19 mm Parabellum-type MKE (Turkey)-brand ammunition were analyzed by scanning electron microscope and energy dispersive X-ray spectrometer. GSR samples were collected by "swab" technique from the shooter's right hand immediately after shooting. According to general principles of thermodynamics, it is likely that the structures will have a more regular (homogeneous) spherical form to minimize their surface area due to very high temperatures and pressures that occur during explosion. Studied samples were collected under the same conditions with the same original ammunition, from the same firearm and a single shooter. This is because many other variables may affect size, structure, and composition in addition to the concentrations of elements of the structure. Results indicated that the chemical compositions are effective in the formation of GSR morphological structures. © 2015 American Academy of Forensic Sciences.

  19. Nano hydroxyapatite-blasted titanium surface affects pre-osteoblast morphology by modulating critical intracellular pathways.

    Science.gov (United States)

    Bezerra, Fábio; Ferreira, Marcel R; Fontes, Giselle N; da Costa Fernandes, Célio Jr; Andia, Denise C; Cruz, Nilson C; da Silva, Rodrigo A; Zambuzzi, Willian F

    2017-08-01

    Although, intracellular signaling pathways are proposed to predict the quality of cell-surface relationship, this study addressed pre-osteoblast behavior in response to nano hydroxyapatite (HA)-blasted titanium (Ti) surface by exploring critical intracellular pathways and pre-osteoblast morphological change. Physicochemical properties were evaluated by atomic force microscopy (AFM) and wettability considering water contact angle of three differently texturized Ti surfaces: Machined (Mac), Dual acid-etching (DAE), and nano hydroxyapatite-blasted (nHA). The results revealed critical differences in surface topography, impacting the water contact angle and later the osteoblast performance. In order to evaluate the effect of those topographical characteristics on biological responses, we have seeded pre-osteoblast cells on the Ti discs for up to 4 h and subjected the cultures to biological analysis. First, we have observed pre-osteoblasts morphological changes resulting from the interaction with the Ti texturized surfaces whereas the cells cultured on nHA presented a more advanced spreading process when compared with the cells cultured on the other surfaces. These results argued us for analyzing the molecular machinery and thus, we have shown that nHA promoted a lower Bax/Bcl2 ratio, suggesting an interesting anti-apoptotic effect, maybe explained by the fact that HA is a natural element present in bone composition. Thereafter, we investigated the potential effect of those surfaces on promoting pre-osteoblast adhesion and survival signaling by performing crystal violet and immunoblotting approaches, respectively. Our results showed that nHA promoted a higher pre-osteoblast adhesion supported by up-modulating FAK and Src activations, both signaling transducers involved during eukaryotic cell adhesion. Also, we have shown Ras-Erk stimulation by the all evaluated surfaces. Finally, we showed that all Ti-texturing surfaces were able to promote osteoblast differentiation

  20. On the dependence of sea surface roughness on wind waves

    DEFF Research Database (Denmark)

    Johnson, H.K.; Højstrup, J.; Vested, H.J.

    1998-01-01

    The influence of wind waves on the momentum transfer (wind stress) between the atmosphere and sea surface was studied using new measured data from the RASEX experiment and other datasets compiled by Donelan et al. Results of the data analysis indicate that errors in wind friction velocity u...... that calculations of the wind friction velocities using the wave-spectra-dependent expression of Hansen and Larsen agrees quite well with measured values during RASEX. It also gives a trend in Charnock parameter consistent with that found by combining the field data. Last, calculations using a constant Charnock...... parameter (0.018) also give very good results for the wind friction velocities at the RASEX site....

  1. View-Dependent Tessellation and Simulation of Ocean Surfaces

    Directory of Open Access Journals (Sweden)

    Anna Puig-Centelles

    2014-01-01

    Full Text Available Modeling and rendering realistic ocean scenes have been thoroughly investigated for many years. Its appearance has been studied and it is possible to find very detailed simulations where a high degree of realism is achieved. Nevertheless, among the solutions to ocean rendering, real-time management of the huge heightmaps that are necessary for rendering an ocean scene is still not solved. We propose a new technique for simulating the ocean surface on GPU. This technique is capable of offering view-dependent approximations of the mesh while maintaining coherence among the extracted approximations. This feature is very important as most solutions previously presented must retessellate from the initial mesh. Our solution is able to use the latest extracted approximation when refining or coarsening the mesh.

  2. Time dependent effect of chronic embryonic exposure to ethanol on zebrafish: Morphology, biochemical and anxiety alterations.

    Science.gov (United States)

    Ramlan, Nurul Farhana; Sata, Nurul Syafida Asma Mohd; Hassan, Siti Norhidayah; Bakar, Noraini Abu; Ahmad, Syahida; Zulkifli, Syaizwan Zahmir; Abdullah, Che Azurahanim Che; Ibrahim, Wan Norhamidah Wan

    2017-08-14

    Exposure to ethanol during critical period of development can cause severe impairments in the central nervous system (CNS). This study was conducted to assess the neurotoxic effects of chronic embryonic exposure to ethanol in the zebrafish, taking into consideration the time dependent effect. Two types of exposure regimen were applied in this study. Withdrawal exposure group received daily exposure starting from gastrulation until hatching, while continuous exposure group received daily exposure from gastrulation until behavioural assessment at 6dpf (days post fertilization). Chronic embryonic exposure to ethanol decreased spontaneous tail coiling at 24hpf (hour post fertilization), heart rate at 48hpf and increased mortality rate at 72hpf. The number of apoptotic cells in the embryos treated with ethanol was significantly increased as compared to the control. We also measured the morphological abnormalities and the most prominent effects can be observed in the treated embryos exposed to 1.50% and 2.00%. The treated embryos showed shorter body length, larger egg yolk, smaller eye diameter and heart edema as compared to the control. Larvae received 0.75% continuous ethanol exposure exhibited decreased swimming activity and increased anxiety related behavior, while withdrawal ethanol exposure showed increased swimming activity and decreased anxiety related behavior as compared to the respective control. Biochemical analysis exhibited that ethanol exposure for both exposure regimens altered proteins, lipids, carbohydrates and nucleic acids of the zebrafish larvae. Our results indicated that time dependent effect of ethanol exposure during development could target the biochemical processes thus leading to induction of apoptosis and neurobehavioral deficits in the zebrafish larvae. Thus it raised our concern about the safe limit of alcohol consumption for pregnant mother especially during critical periods of vulnerability for developing nervous system. Copyright © 2017

  3. Three-dimensional morphological characterization of the skin surface micro-topography using a skin replica and changes with age.

    Science.gov (United States)

    Masuda, Y; Oguri, M; Morinaga, T; Hirao, T

    2014-08-01

    Skin surface micro-topography (SSMT), consisting of pores, ridges and furrows, reflects the skin condition and is an important factor determining the aesthetics of the skin. Most previous studies evaluating SSMT have employed two-dimensional image analysis of magnified pictures captured by a video microscope. To improve the accuracy of SSMT analysis, we established a three-dimensional (3D) analysis method for SSMT and developed various parameters including the skin ridge number, and applied the method to study the age-dependent change in skin. Confocal laser scanning microscopy was used for 3D measurement of the surface morphology of silicon replicas taken from the cheek. We then used these data to calculate the parameters that reflect the nature of SSTM including the skin ridge number using originally developed software. Employing a superscription technique, we investigated the variation in SSMT with age for replicas taken from the cheeks of 103 Japanese females (5-85 years old). The skin surface area and roughness, the area of pores, the area, length, depth and width of skin furrows and the number of skin ridges were examined. The surface roughness, the area of pores and the depth of skin furrows increased with age. The area and length of skin furrows and the number of skin ridges decreased with age. The method proposed to analyse SSMT three dimensionally is an effective tool with which to characterize the condition of the skin. © 2013 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  4. Patterns of morphological variation in enamel-dentin junction and outer enamel surface of human molars.

    Science.gov (United States)

    Morita, Wataru; Yano, Wataru; Nagaoka, Tomohito; Abe, Mikiko; Ohshima, Hayato; Nakatsukasa, Masato

    2014-06-01

    Tooth crown patterning is governed by the growth and folding of the inner enamel epithelium (IEE) and the following enamel deposition forms outer enamel surface (OES). We hypothesized that overall dental crown shape and covariation structure are determined by processes that configurate shape at the enamel-dentine junction (EDJ), the developmental vestige of IEE. This this hypothesis was tested by comparing patterns of morphological variation between EDJ and OES in human permanent maxillary first molar (UM1) and deciduous second molar (um2). Using geometric morphometric methods, we described morphological variation and covariation between EDJ and OES, and evaluated the strength of two components of phenotypic variability, canalization and morphological integration, in addition to the relevant evolutionary flexibility, i.e. the ability to respond to selective pressure. The strength of covariation between EDJ and OES was greater in um2 than in UM1, and the way that multiple traits covary between EDJ and OES was different between these teeth. The variability analyses showed that EDJ had less shape variation and a higher level of morphological integration than OES, which indicated that canalization and morphological integration acted as developmental constraints. These tendencies were greater in UM1 than in um2. On the other hand, EDJ and OES had a comparable level of evolvability in these teeth. Amelogenesis could play a significant role in tooth shape and covariation structure, and its influence was not constant among teeth, which may be responsible for the differences in the rate and/or period of enamel formation. © 2014 Anatomical Society.

  5. THE DEPENDENCE OF STAR FORMATION EFFICIENCY ON GAS SURFACE DENSITY

    International Nuclear Information System (INIS)

    Burkert, Andreas; Hartmann, Lee

    2013-01-01

    Studies by Lada et al. and Heiderman et al. have suggested that star formation mostly occurs above a threshold in gas surface density Σ of Σ c ∼ 120 M ☉ pc –2 (A K ∼ 0.8). Heiderman et al. infer a threshold by combining low-mass star-forming regions, which show a steep increase in the star formation rate per unit area Σ SFR with increasing Σ, and massive cores forming luminous stars which show a linear relation. We argue that these observations do not require a particular density threshold. The steep dependence of Σ SFR , approaching unity at protostellar core densities, is a natural result of the increasing importance of self-gravity at high densities along with the corresponding decrease in evolutionary timescales. The linear behavior of Σ SFR versus Σ in massive cores is consistent with probing dense gas in gravitational collapse, forming stars at a characteristic free-fall timescale given by the use of a particular molecular tracer. The low-mass and high-mass regions show different correlations between gas surface density and the area A spanned at that density, with A ∼ Σ –3 for low-mass regions and A ∼ Σ –1 for the massive cores; this difference, along with the use of differing techniques to measure gas surface density and star formation, suggests that connecting the low-mass regions with massive cores is problematic. We show that the approximately linear relationship between dense gas mass and stellar mass used by Lada et al. similarly does not demand a particular threshold for star formation and requires continuing formation of dense gas. Our results are consistent with molecular clouds forming by galactic hydrodynamic flows with subsequent gravitational collapse

  6. Surface morphology and physical properties of partially melt textured Mn doped Bi-2223

    Directory of Open Access Journals (Sweden)

    Indu Verma

    2011-09-01

    Full Text Available The samples of Bi2Sr2Ca2Cu3-xMnxO10+δ (x = 0.0 to 0.30 were prepared by the standard solid-state reaction method. The phase identification characteristics of synthesized (HTSC materials were explored through powder X-ray diffractometer reveals that all the samples crystallize in orthorhombic structure with lattice parameters a = 5.4053 Å, b = 5.4110 Å and c = 37.0642 Å up to Mn concentration of x = 0.30. The critical temperature (Tc measured by standard four probe method has been found to depress from 108 K to 70 K as Mn content (x increases from 0.00 to 0.30. The effects of sintering temperature on the surface morphology of Bi2Sr2Ca2Cu3-xMnxO10+δ have also been investigated. The surface morphology investigated through scanning electron microscope and atomic force microscopy (SEM & AFM results that voids are decreasing but grains size increases as the Mn concentration increases besides, nanosphere like structures on the surface of the Mn doped Bi2Sr2Ca2Cu3-xMnxO10+δ (Bi-2223 samples.

  7. The Effect of Laminin-1-Doped Nanoroughened Implant Surfaces: Gene Expression and Morphological Evaluation

    Directory of Open Access Journals (Sweden)

    Humberto Osvaldo Schwartz-Filho

    2012-01-01

    Full Text Available Aim. This study aimed to observe the morphological and molecular effect of laminin-1 doping to nanostructured implant surfaces in a rabbit model. Materials and Methods. Nanostructured implants were coated with laminin-1 (test; dilution, 100 μg/mL and inserted into the rabbit tibiae. Noncoated implants were used as controls. After 2 weeks of healing, the implants were removed and subjected to morphological analysis using scanning electron microscopy (SEM and gene expression analysis using the real-time reverse transcriptase-polymerase chain reaction (RT-PCR. Results. SEM revealed bony tissue attachment for both control and test implants. Real-time RT-PCR analysis showed that the expression of osteoblast markers RUNX-2, osteocalcin, alkaline phosphatase, and collagen I was higher (1.62-fold, 1.53-fold, 1.97-fold, and 1.04-fold, resp. for the implants modified by laminin-1 relative to the control. All osteoclast markers investigated in the study presented higher expression on the test implants than controls as follows: tartrate-resistant acid phosphatase (1.67-fold, calcitonin receptor (1.35-fold, and ATPase (1.25-fold. The test implants demonstrated higher expression of inflammatory markers interleukin-10 (1.53-fold and tumour necrosis factor-α (1.61-fold relative to controls. Conclusion. The protein-doped surface showed higher gene expression of typical genes involved in the osseointegration cascade than the control surface.

  8. Surface morphology of Saccinobaculus (Oxymonadida): implications for character evolution and function in oxymonads.

    Science.gov (United States)

    Carpenter, Kevin J; Waller, Ross F; Keeling, Patrick J

    2008-04-01

    Examination of surface morphology of the oxymonad genus Saccinobaculus from the gut of the wood-feeding cockroach Cryptocercus punctulatus with scanning and transmission electron microscopy reveals several new characters not observable with light microscopy. These include small concavities covering the external surface, a glycocalyx, coated pinocytotic vesicles, and, in one species, unidentified, membrane-bounded organelles with a granular matrix that may represent peroxisomal or mitochondrial derivatives. Unlike representatives of some other oxymonad families, Saccinobaculus lacks extracellular surface structures, a holdfast, and, generally, ectobiotic bacteria. We examined the evolution of these and other characters in light of previously published phylogenies of oxymonads based on molecular data. The presence of concavities in Saccinobaculus and families Pyrsonymphidae and Oxymonadidae strengthens support for a clade comprising these three families. A glycocalyx appears to be a synapomorphy of all oxymonads, and the presence of ectobiotic bacteria also appears to be ancestral to oxymonads, but lost in Saccinobaculus. A holdfast appears to have arisen multiple times. We hypothesize that concavities may play a role in a two-step mechanism for the accumulation and internalization of specific solutes, and that the highly motile and morphologically plastic nature of Saccinobaculus cells limits the possibility of retaining a covering of ectobiotic bacteria.

  9. Evaluation of ablation efficiency and surface morphology of human teeth upon irradiation with femtosecond laser pulses

    Science.gov (United States)

    Shaheen, M. E.; Gagnon, J. E.; Fryer, B. J.

    2014-11-01

    This study investigates changes in ablation efficiency and surface morphology induced in human dental enamel and dentin upon interaction with femtosecond laser pulses at variable energies and number of laser pulses. Craters were created using a Ti:sapphire femtosecond laser ablation system operating at a wavelength of 785 nm, pulse width of 130 fs, and repetition rate of 20 Hz. Various techniques, such as optical and scanning electron microscopy and inductively coupled plasma mass spectrometry (ICP-MS), were used to evaluate ablation depth, amount of material ablated, and surface morphology of the craters. Ablation rate (ablation depth per pulse) was found to be lower in enamel than dentin with the maximum rate occurring at fluence of 12.4 J cm-2 in both materials. A drop in ablation rate was observed for fluence greater than 12.4 J cm-2 and was attributed to attenuation of laser energy due to interaction with the laser-generated particles. Above this fluence, signs of thermal effects, such as melting and formation of droplets of molten material at the sample surface, were observed. The response of the ICP-MS indicated that the amount of ablated material removed from dentin is greater than that removed from enamel by a factor of 1.5 or more at all investigated fluence.

  10. Surface morphology of refractive-index waveguide gratings fabricated in polymer films

    Science.gov (United States)

    Dong, Yi; Song, Yan-fang; Ma, Lei; Gao, Fang-fang

    2016-09-01

    The characteristic modifications are reported on the surface of polymeric waveguide film in the process of volume- grating fabrication. The light from a mode-locked 76 MHz femtosecond laser with pulse duration of 200 fs and wavelength of 800 nm is focused normal to the surface of the sample. The surface morphology modifications are ascribed to a fact that surface swelling occurs during the process. Periodic micro-structure is inscribed with increasing incident power. The laser-induced swelling threshold on the grating, which is higher than that of two-photon initiated photo-polymerization (TPIP) (8 mW), is verified to be about 20 mW. It is feasible to enhance the surface smoothness of integrated optics devices for further encapsulation. The variation of modulation depth is studied for different values of incident power and scan spacing. Ablation accompanied with surface swelling appears when the power is higher. By optimizing the laser carving parameters, highly efficient grating devices can be fabricated.

  11. Meniscus matrix morphological composition: age-dependent evaluation in a swine model

    Directory of Open Access Journals (Sweden)

    Umberto Polito

    2017-06-01

    Full Text Available Menisci are fibro-cartilaginous structures interposed between femoral condyle and tibial plateau, which have multiple functions in the stifle joint: act as shock absorbers, bear loaders and allow joint stability, congruity and lubrication (Sweigart et al., 2004; Proffen et al., 2012. It is well known that meniscal injuries lead to osteoarthritis and for these reasons, menisci are considered important target of investigation. Their important role in the knee wellness is only equalled by their deficiency in proper self-repairing. Nowadays, the gold standard technique is not just to remove the damaged meniscus, but to rebuild it or to replace it. For these reasons, studies are necessary to increase the knowledge about these small but essential structures (Streuli, 1999; Deponti et al., 2013. Composition and morphology are basic fundamental information for the development of engineered meniscal substitutes (Di Giancamillo et al., 2014. The analysis of the morphological, structural and biochemical changes, which occur during growth of the normal menisci, represent the goal of the present study. For this purpose, menisci from adult (7-month old, young (1-month old, and neonates (stillbirths pigs were collected. Cellularity and glycosamiglycans (GAGs deposition were evaluated by ELISA, while Collagen-1 and Collagen-2 were investigated by immunohistochemistry and Western blot analyses. Cellularity (P<0.01, all comparisons and Collagen-1 (P<0.05, neonatal-young vs adult decreased from neonatal to adult stage while GAGs (P<0.01 neonatal vs young-adult and Collagen-2 (P<0.01 neonatal-young vs adult showed the opposite trend. Immunohistochemistry revealed similar changes occurring during animal growth thus revealing that cellular phenotype, cellularity and protein expression, as well as fibers aggregation in the matrix, are dissimilar in the three ages analysed categories. These changes reflect the progressive menisci maturation and hyper-specialisation. We

  12. Surface morphology of the endolymphatic duct in the rat. A scanning electron microscopy study

    DEFF Research Database (Denmark)

    Qvortrup, K; Rostgaard, Jørgen; Bretlau, P

    1995-01-01

    were identified with the scanning electron microscope. A polygonal and oblong epithelial cell was observed in the largest number throughout the duct, and in the juxtasaccular half of the duct, two additional types of epithelial cells were observed. The scanning electron microscopic observations...... microscopy was attained by coating of the specimens with osmium tetroxide and thiocarbohydrazide followed by a continuous dehydration procedure. This technique permitted, for the first time, an investigation of the surface morphology of the epithelial cells in the endolymphatic duct. Three types of cells...... are compared and discussed with reference to previous transmission electron microscopic studies of the endolymphatic duct....

  13. Surface morphology study of Zr-based amorphous alloys after immersion in boiling nitric acid medium

    Science.gov (United States)

    Sharma, Poonam; Dhawan, Anil; Sharma, S. K.

    2016-05-01

    Weight loss studies have been performed to determine the corrosion resistance of amorphous Zr60Nb2Al10Ni8Cu20 and Zr59Nb3Al10Ni8Cu20 alloys in aqueous HNO3 media at boiling temperature. The FESEM micrographs has been obtained to know the surface morphology of specimens after immersion in 11.5M boiling aqueous HNO3 media. Zr59Nb3Al10Ni8Cu20 alloy shows better corrosion resistance in nitric acid media than Zr60Nb2Al10Ni8Cu20 alloy.

  14. Prediction Surface Morphology of Nanostructure Fabricated by Nano-Oxidation Technology

    OpenAIRE

    Huang, Jen-Ching; Chang, Ho; Kuo, Chin-Guo; Li, Jeen-Fong; You, Yong-Chin

    2015-01-01

    Atomic force microscopy (AFM) was used for visualization of a nano-oxidation technique performed on diamond-like carbon (DLC) thin film. Experiments of the nano-oxidation technique of the DLC thin film include those on nano-oxidation points and nano-oxidation lines. The feature sizes of the DLC thin film, including surface morphology, depth, and width, were explored after application of a nano-oxidation technique to the DLC thin film under different process parameters. A databank for process ...

  15. Surface conductivity dependent dynamic behaviour of an ultrafine atmospheric pressure plasma jet for microscale surface processing

    Energy Technology Data Exchange (ETDEWEB)

    Abuzairi, Tomy [Graduate School of Science and Technology, Shizuoka University, Hamamatsu 432-8561 (Japan); Department of Electrical Engineering, Faculty of Engineering, Universitas Indonesia, Depok 16424 (Indonesia); Okada, Mitsuru [Department of Engineering, Shizuoka University, Hamamatsu 432-8561 (Japan); Bhattacharjee, Sudeep [Department of Physics, Indian Institute of Technology, Kanpur 208016 (India); Nagatsu, Masaaki, E-mail: nagatsu.masaaki@shizuoka.ac.jp [Graduate School of Science and Technology, Shizuoka University, Hamamatsu 432-8561 (Japan); Department of Engineering, Shizuoka University, Hamamatsu 432-8561 (Japan); Research Institute of Electronics, Shizuoka University, Hamamatsu 432-8561 (Japan)

    2016-12-30

    Highlights: • Spatio-temporal behaviors of capillary APPJs are studied for various substrates. • Plasma irradiation area depended on the substrate conductivity and permittivity. • Surface irradiation area was significantly broadened in polymer-like substrate. • Effect of applying a substrate bias on the APPJ irradiation area was investigated. - Abstract: An experimental study on the dynamic behaviour of microcapillary atmospheric pressure plasma jets (APPJs) with 5 μm tip size for surfaces of different conductivity is reported. Electrical and spatio-temporal characteristics of the APPJs are monitored using high voltage probe, current monitor and high speed intensified charge couple device camera. From these experimental results, we presented a simple model to understand the electrical discharge characteristics of the capillary APPJs with double electrodes, and estimated the velocity of the ionization fronts in the jet and the electron density to be 3.5–4.2 km/s and 2–7 × 10{sup 17} m{sup −3}. By analyzing the dynamics of the microcapillary APPJs for different substrate materials, it was found that the surface irradiation area strongly depended on the substrate conductivity and permittivity, especially in the case of polymer-like substrate, surface irradiation area was significantly broadened probably due to the repelling behaviour of the plasma jets from the accumulated electrical charges on the polymer surface. The effect of applying a substrate bias in the range from −900 V to +900 V on the plasma irradiation onto the substrates was also investigated. From the knowledge of the present results, it is helpful for choosing the substrate materials for microscale surface modification.

  16. Abnormal surface morphology of the central sulcus in children with attention-deficit/hyperactivity disorder

    Directory of Open Access Journals (Sweden)

    Shuyu eLi

    2015-08-01

    Full Text Available The central sulcus (CS divides the primary motor and somatosensory areas, and its three-dimensional (3D anatomy reveals the structural changes of the sensorimotor regions. Attention-deficit/hyperactivity disorder (ADHD is a neurodevelopmental disorder that is associated with sensorimotor and executive function deficits. However, it is largely unknown whether the morphology of the CS alters due to inappropriate development in the ADHD brain. Here, we employed the sulcus-based morphometry approach to investigate the 3D morphology of the CS in 42 children whose ages spanned from 8.8 to 13.5 years (21 with ADHD and 21 controls. After automatic labeling of each CS, we computed 7 regional shape metrics for each CS, including the global average length, average depth, maximum depth, average span, surface area, average cortical thickness and local sulcal profile. We found that the average depth and maximum depth of the left CS as well as the average cortical thickness of bilateral CS in the ADHD group were significantly larger than those in the healthy children. Moreover, significant between-group differences in the sulcal profile had been found in middle sections of the CSs bilaterally, and these changes were positively correlated with the hyperactivity-impulsivity scores in the children with ADHD. Altogether, our results provide evidence for the abnormity of the CS anatomical morphology in children with ADHD due to the structural changes in the motor cortex, which significantly contribute to the clinical symptomatology of the disorder.

  17. The ultrastructural surface morphology of oral cancer cells and keratinocytes after exposure to chitosan

    Science.gov (United States)

    Fatimah; Sarsito, A. S.; Wimardhani, Y. S.

    2017-08-01

    Low-molecular-weight chitosan (LMWC) has the same selective cytotoxic effects on oral cancer cells as cisplatin. The cell deaths caused by the anticancer characteristics of chitosan show that apoptosis is not the death pathway of the primary cells involved. The interactions between LMWC and the cells need to be explored. The objective of this study was to compare the ultrastructural morphology of oral Squamous Cell Carcinoma (SCC Ca)-922 and noncancer keratinocyte HaCaT cell lines after exposure to LMWC and cisplatin. The cells were treated with LMWC and cisplatin, and their ultrastructural morphology was analyzed using scanning electron micrographs. Features of early apoptosis, seen as the loss of microvilli, were detected in the LMWC-exposed Ca9-22 cells, and there was a material surrounding the cells. In contrast, the LMWC-exposed HaCaT cells showed no changes related to apoptosis. The results were the opposite when cisplatin was used. This study confirms that there are differences in the ultrastructural surface morphology of LMWC-exposed and cisplatin-exposed oral cancer cells and keratinocytes that could be correlated with their biological activity.

  18. Helium concentration in tungsten nano-tendril surface morphology using Elastic Recoil Detection

    International Nuclear Information System (INIS)

    Woller, K.B.; Whyte, D.G.; Wright, G.M.; Doerner, R.P.; De Temmerman, G.

    2013-01-01

    Helium (He) concentrations in tungsten nano-tendrils (W fuzz) have been measured for the first time using Elastic Recoil Detection (ERD). Fuzzy and non-fuzzy W surfaces were analyzed in order to illuminate the role of He in the transition in surface morphologies. Samples grown in the PISCES-A and PILOT-PSI experiments allowed a survey of surface temperature ranging from T s = 470–2595 K and of He fluence on the order of Φ He ∼ 10 24 –10 27 ions/m 2 . He concentrations measured in the bulk of W fuzz layers are roughly uniform with bulk He concentration 1–4 at.% while samples with just He in the near surface peaked at 1–2 at.%. This confirms that the nano-tendrils are filled with high pressure He bubbles since the solubility of He in W is ∼10 −5 at.%. This indicates that the ∼1000 K temperature fuzz-growth threshold is determined by the response of the W, not the near-surface He concentration

  19. Effect of surface morphology and densification on the infrared emissivity of C/SiC composites

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Fuyuan, E-mail: wangfy1986@gmail.com; Cheng, Laifei; Zhang, Qing, E-mail: zhangqing@nwpu.edu.cn; Zhang, Litong

    2014-09-15

    Highlights: • The cauliflower-like microstructure improved the infrared emissivity multiply. • The infrared emissivity decreased continually with the improving surface flatness. • The densification process boosted the infrared emissivity. - Abstract: The effects of surface morphology and densification on the infrared emissivity of 2D C/SiC composites were investigated in 6–16 μm from 1000 °C to 1600 °C. As the sample surface was polished, the reflection and scattering for the electromagnetic waves of thermal radiation were reduced, causing a sustained decrease in the infrared emissivity. The space-variant polarizations caused by the cauliflower-like microstructure were enervated in the smooth surface, which enhanced the reduction trendy in the infrared emissivity. In densification process, the increasing SiC content and the growing amount of the cauliflower-like microstructure on sample surface improved the infrared emissivity of C/SiC composites, while the decreasing porosity decreased it. Due to the greater positive effects on the thermal radiation during the densification process, the infrared emissivity of C/SiC composites increased successively with density.

  20. Nano-microsized modification of the surface morphology and composition of Ti-based dental implants

    Science.gov (United States)

    Joob, Arpad F.; Divinyi, T.; Fazekas, A.; Daroczi, C. S.; Karacs, A.; Peto, G.

    2001-11-01

    It can be concluded that surface treatment with high power Nd laser pulses induces unique morphology with sizes in ten micron and 50 nanometer ranges and being topologically isomorf with the plane. It is clear that the 1-10 micrometer elements do not change strongly the osseintegration compared to the flat surface. On the other hand this surface in 20-50 micrometer range already enhance the osseointegration indicating a strong size dependens. The effect of the nanosized elements can be suggested also because their density has been increased with laser intensity. These two effects can not be separated with available data. It is evident that several questions in connection with laser treatment of surfaces such as first of all the time course of bone formation await further studies. Namely, if microgeometry plays a role in bone formation then the process of osseointegration should be also studied in conjunction with the comparisons of the various surfaces. It is hoped that our future studies can give responses to more questions and the results will contribute to the implementation of novel clinically successful techniques to improve the reliability of dental implants.

  1. Evolution effects of the copper surface morphology on the nucleation density and growth of graphene domains at different growth pressures

    Energy Technology Data Exchange (ETDEWEB)

    Hedayat, Seyed Mahdi [Transport Phenomena & Nanotechnology Lab., School of Chemical Engineering, College of Engineering, University of Tehran (Iran, Islamic Republic of); Karimi-Sabet, Javad, E-mail: j_karimi@alum.sharif.edu [NFCRS, Nuclear Science and Technology Research Institute, Tehran (Iran, Islamic Republic of); Shariaty-Niassar, Mojtaba, E-mail: mshariat@ut.ac.ir [Transport Phenomena & Nanotechnology Lab., School of Chemical Engineering, College of Engineering, University of Tehran (Iran, Islamic Republic of)

    2017-03-31

    Highlights: • Manipulation of the Cu surface morphology in a wide range by electropolishing treatment. • Comparison of the nucleation density of graphene at low pressure and atmospheric pressure CVD processes. • Controlling the evolution of the Cu surface morphology inside a novel confined space. • Growth of large-size graphene domains. - Abstract: In this work, we study the influence of the surface morphology of the catalytic copper substrate on the nucleation density and the growth rate of graphene domains at low and atmospheric pressure chemical vapor deposition (LPCVD and APCVD) processes. In order to obtain a wide range of initial surface morphology, precisely controlled electropolishing methods were developed to manipulate the roughntreess value of the as-received Cu substrate (RMS = 30 nm) to ultra-rough (RMS = 130 nm) and ultra-smooth (RMS = 2 nm) surfaces. The nucleation and growth of graphene domains show obviously different trends at LPCVD and APCVD conditions. In contrast to APCVD condition, the nucleation density of graphene domains is almost equal in substrates with different initial roughness values at LPCVD condition. We show that this is due to the evolution of the surface morphology of the Cu substrate during the graphene growth steps. By stopping the surface sublimation of copper substrate in a confined space saturated with Cu atoms, the evolution of the Cu surface was impeded. This results in the reduction of the nucleation density of graphene domains up to 24 times in the pre-smoothed Cu substrates at LPCVD condition.

  2. Structure, composition and morphology of bioactive titanate layer on porous titanium surfaces

    Science.gov (United States)

    Li, Jinshan; Wang, Xiaohua; Hu, Rui; Kou, Hongchao

    2014-07-01

    A bioactive coating was produced on pore surfaces of porous titanium samples by an amendatory alkali-heat treatment method. Porous titanium was prepared by powder metallurgy and its porosity and average size were 45% and 135 μm, respectively. Coating morphology, coating structure and phase constituents were examined by SEM, XPS and XRD. It was found that a micro-network structure with sizes of bone-like carbonate-hydroxylapatite showing a good biocompatibility was detected on the coating surface. And the redundant Ca advanced the bioactivity of the coating. Thus, the present modification is expected to allow the use of the bioactive porous titanium as artificial bones even under load-bearing conditions.

  3. Surface morphology study on CdZnTe crystals by atomic force microscopy

    Energy Technology Data Exchange (ETDEWEB)

    Azoulay, M.; George, M.A.; Burger, A.; Collins, W.E.; Silberman, E. [Fisk Univ., Nashville, TN (United States)

    1993-03-01

    The study of the crystal surface morphology of CdZnTe is important for the understanding of the fundamentals of crystal growth in order to improve the crystal quality which is essential in applications such as substrates for epitaxy or performance of devices, i.e., room temperature nuclear spectrometers. We present a first atomic force microscopy study on CdZnTe. Cleaved (110) surfaces were imaged in the ambient and an atomic layer step structure was revealed. The effects of thermal annealing on the atomic steps together with Te precipitation along these steps are discussed in terms of deformation due to stress relief and the diffusion of tellurium precipitates. 12 refs., 3 figs.

  4. Relationship between surface structure and morphology of Fe3O4/silica composite nanospheres and nucleic acid extraction

    International Nuclear Information System (INIS)

    Zeng Wen; Xu Hong; Yang Yongzhe; Gu Hongchen

    2009-01-01

    Fe 3 O 4 /silica composite nanospheres with different surface structure and morphology were synthesized by changing reaction conditions. As-synthesized nanospheres were characterized by high performance particle sizer (HPPS), transmission electron microscopy (TEM), nitrogen adsorption and thermogravimetry (TGA). Besides thoroughly characterization, the particles were used for DNA extraction. We found that the particle surface structure and morphology affected the nucleic acid extraction efficiency. When comparing different samples with the same silanol density (10 18 ), the one with a surface area of 60.37 m 2 /g extracted DNA most effectively. Also, with increasing silanol density per surface area, DNA extraction efficiency increased.

  5. Morphology modification of gold nanoparticles from nanoshell to C-shape: Improved surface enhanced Raman scattering

    International Nuclear Information System (INIS)

    Xing, Ting-Yang; Zhu, Jian; Li, Jian-Jun; Zhao, Jun-Wu

    2016-01-01

    Morphology modification of nanostructures is of great interest, because it can be used to fabricate nanostructures which are hard to be done using other methods. Different from traditional lithographic technique which is slow and expensive, morphology modification is easy, cheap, and reproducible. In this paper, modification of the optical and morphological properties of a hollow gold nanoshell (HGNS) is achieved by using H 2 O 2 as an oxidizer. The reshaping of these nanostructures has been demonstrated as a consequence of an oxidation process in which HGNSs are dissolved by H 2 O 2 under the acidic conditions provided by HCl. We investigate the oxidation process by a transmission electron microscope and propose a reshaping model involving four different shapes (HGNS, HGNS with hole, gold nanoring, and C-shaped gold nanoparticle) which are corresponding to the oxidation products of HGNSs at different pH values. Besides, the surface enhanced Raman scattering (SERS) activity of each oxidation product has been evaluated by using rhodamine 6G as the Raman active probe. It has been observed that the C-shaped gold nanoparticles which are corresponding to the oxidation products at the minimum pH value have the highest SERS activity and this result can also be interpreted by discrete-dipole approximation simulations. We demonstrate that the morphology modification of HGNSs becomes possible in a controlled manner using wet chemistry and can be used in preparation of gold nanoparticles such as HGNS with hole, gold nanoring, and C-shaped gold nanoparticle with large SERS activity. These nanostructures must have potential use in many plasmonic areas, including sensing, catalysis, and biomedicine.

  6. Controlled surface morphology and hydrophilicity of polycaprolactone toward human retinal pigment epithelium cells

    International Nuclear Information System (INIS)

    Shahmoradi, Saleheh; Yazdian, Fatemeh; Tabandeh, Fatemeh; Soheili, Zahra-Soheila; Hatamian Zarami, Ashraf Sadat; Navaei-Nigjeh, Mona

    2017-01-01

    Applying scaffolds as a bed to enhance cell proliferation and even differentiation is one of the treatment of retina diseases such as age-related macular degeneration (AMD) which deteriorating photoreceptors and finally happening blindness. In this study, aligned polycaprolactone (PCL) nanofibers were electrospun and at different conditions and their characteristics were measured by scanning electron microscope (SEM) and contact angle. Response surface methodology (RSM) was used to optimize the diameter of fabricated nanofibers. Two factors as solution concentration and voltage value were considered as independent variables and their effects on nanofibers' diameters were evaluated by central composite design and the optimum conditions were obtained as 0.12 g/mL and 20 kV, respectively. In order to decrease the hydrophobicity of PCL, the surface of the fabricated scaffolds was modified by alkaline hydrolysis method. Contact time of the scaffolds and alkaline solution and concentration of alkaline solution were optimized using Box Behnken design and (120 min and 5 M were the optimal, respectively). Contact angle measurement showed the high hydrophilicity of treated scaffolds (with contact angle 7.48°). Plasma surface treatment was applied to compare the effect of using two kinds of surface modification methods simultaneously on hydrolyzed scaffolds. The RPE cells grown on scaffolds were examined by immunocytochemistry (ICC), MTT and continuous inspection of cellular morphology. Interestingly, Human RPE cells revealed their characteristic morphology on hydrolyzed scaffold well. As a result, we introduced a culture substrate with low diameter (185.8 nm), high porosity (82%) and suitable hydrophilicity (with contact angle 7.48 degree) which can be promising for hRPE cell transplantation. - Highlights: • Dimethylformamide (DMF) has significant effect on reduction of fibers' diameter. • Having high hydrophilicity by alkaline hydrolysis • Suitable

  7. Studies on the Optical Properties and Surface Morphology of Cobalt Phthalocyanine Thin Films

    Directory of Open Access Journals (Sweden)

    Benny Joseph

    2008-01-01

    Full Text Available Thin films of Cobalt Phthalocyanine (CoPc are fabricated at a base pressure of 10-5 m.bar using Hind-Hivac thermal evaporation plant. The films are deposited on to glass substrates at various temperatures 318, 363, 408 and 458K. The optical absorption spectra of these thin films are measured. The present studies reveal that the optical band gap energies of CoPc thin films are almost same on substrate temperature variation. The structure and surface morphology of the films deposited on glass substrates of temperatures 303, 363 and 458K are studied using X-ray diffractograms and Scanning Electron Micrographs (SEM, which show that there is a change in the crystallinity and surface morphology due to change in the substrate temperatures. Full width at half maximum (FWHM intensity of the diffraction peaks is also found reduced with increasing substrate temperatures. Scanning electron micrographs show that these crystals are needle like, which are interconnected at high substrate temperatures. The optical band gap energy is almost same on substrate temperature variation. Trap energy levels are also observed for these films.

  8. Surface morphology influence on deuterium retention in beryllium films prepared by thermionic vacuum arc method

    International Nuclear Information System (INIS)

    Anghel, A.; Porosnicu, C.; Badulescu, M.; Mustata, I.; Lungu, C.P.; Sugiyama, K.; Lindig, S.; Krieger, K.; Roth, J.; Nastuta, A.; Rusu, G.; Popa, G.

    2009-01-01

    In a plasma-confinement device, material eroded from plasma facing components will be transported and re-deposited at other locations inside the reaction chamber. Since beryllium from the first wall of the ITER fusion reactor will be eroded, ionized in the scrape-off layer plasma and finally re-deposited on divertor surfaces flowing along the magnetic field, it is important to study the properties of divertor armour materials (C, W) coated with beryllium. By applying different bias voltages (-200 V to +700 V) to the substrates during deposition, the morphology of the obtained films was modified. The films' morphology was characterized by means of AFM and SEM, and it was found that the coatings prepared using negative bias voltage at the substrate during deposition are more compact and have a smoother surface compared to the samples prepared with positive bias voltage. The thickness and composition of each film were measured using Rutherford backscattering spectrometry (RBS). A study of deuterium implantation and retention into the prepared films was performed at IPP Garching in the high current ion source.

  9. On the Morphology of the SDS Film on the Surface of Borosilicate Glass

    Directory of Open Access Journals (Sweden)

    Zih-Yao Shen

    2017-05-01

    Full Text Available Surfactant films on solid surfaces have attracted much attention because of their scientific interest and applications, such as surface treatment agent, or for micro- or nano-scale templates for microfluidic devices. In this study, anionic surfactant sodium dodecyl sulfate (SDS solutions with various charged inorganic salts was spread on a glass substrate and dried to form an SDS thin film. Atomic force microscopy (AFM was employed to observe the micro-structure of the SDS thin film. The effects of inorganic salts on the morphology of the SDS film were observed and discussed. The results of experiments demonstrated that pure SDS film formed patterns of long, parallel, highly-ordered stripes. The existence of the inorganic salt disturbed the structure of the SDS film due to the interaction between the cationic ion and the anionic head groups of SDS. The divalent ion has greater electrostatic interaction with anionic head groups than that of the monovalent ion, and causes a gross change in the morphology of the SDS film. The height of the SDS bilayer measured was consistent with the theoretical value, and the addition of the large-sized monovalent ion would lead to lowering the height of the adsorbed structures.

  10. Structure, morphology, and magnetic properties of Fe nanoparticles deposited onto single-crystalline surfaces

    Directory of Open Access Journals (Sweden)

    Armin Kleibert

    2011-01-01

    Full Text Available Background: Magnetic nanostructures and nanoparticles often show novel magnetic phenomena not known from the respective bulk materials. In the past, several methods to prepare such structures have been developed – ranging from wet chemistry-based to physical-based methods such as self-organization or cluster growth. The preparation method has a significant influence on the resulting properties of the generated nanostructures. Taking chemical approaches, this influence may arise from the chemical environment, reaction kinetics and the preparation route. Taking physical approaches, the thermodynamics and the kinetics of the growth mode or – when depositing preformed clusters/nanoparticles on a surface – the landing kinetics and subsequent relaxation processes have a strong impact and thus need to be considered when attempting to control magnetic and structural properties of supported clusters or nanoparticles.Results: In this contribution we focus on mass-filtered Fe nanoparticles in a size range from 4 nm to 10 nm that are generated in a cluster source and subsequently deposited onto two single crystalline substrates: fcc Ni(111/W(110 and bcc W(110. We use a combined approach of X-ray magnetic circular dichroism (XMCD, reflection high energy electron diffraction (RHEED and scanning tunneling microscopy (STM to shed light on the complex and size-dependent relation between magnetic properties, crystallographic structure, orientation and morphology. In particular XMCD reveals that Fe particles on Ni(111/W(110 have a significantly lower (higher magnetic spin (orbital moment compared to bulk iron. The reduced spin moments are attributed to the random particle orientation being confirmed by RHEED together with a competition of magnetic exchange energy at the interface and magnetic anisotropy energy in the particles. The RHEED data also show that the Fe particles on W(110 – despite of the large lattice mismatch between iron and tungsten – are

  11. Surface morphological modification of crosslinked hydrophilic co-polymers by nanosecond pulsed laser irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Primo, Gastón A.; Alvarez Igarzabal, Cecilia I. [IMBIV (CONICET), Departamento de Química Orgánica, Facultad de Ciencias Químicas, Universidad Nacional de Córdoba, Haya de la Torre y Medina Allende, Edificio de Ciencias II, Ciudad Universitaria, Córdoba X5000HUA (Argentina); Pino, Gustavo A.; Ferrero, Juan C. [INFIQC (CONICET), Departamento de Fisicoquímica, Facultad de Ciencias Químicas, and Centro Láser de Ciencias Moleculares, Universidad Nacional de Córdoba, Córdoba X5000IUS (Argentina); Rossa, Maximiliano, E-mail: mrossa@fcq.unc.edu.ar [INFIQC (CONICET), Departamento de Fisicoquímica, Facultad de Ciencias Químicas, and Centro Láser de Ciencias Moleculares, Universidad Nacional de Córdoba, Córdoba X5000IUS (Argentina)

    2016-04-30

    Graphical abstract: - Highlights: • Laser-induced surface modification of crosslinked hydrophilic co-polymers by ns pulses. • Formation of ablation craters observed under most of the single-pulse experimental conditions. • UV laser foaming of dried hydrogel samples resulting from single- and multiple-pulse experiments. • Threshold values of the incident laser fluence reported for the observed surface modifications. • Lower threshold fluences for acrylate-based, compared to acrylamide-based hydrogels. - Abstract: This work reports an investigation of the surface modifications induced by irradiation with nanosecond laser pulses of ultraviolet and visible wavelengths on crosslinked hydrophilic co-polymeric materials, which have been functionalized with 1-vinylimidazole as a co-monomer. A comparison is made between hydrogels differing in the base co-monomer (N,N-dimethylaminoethyl methacrylate and N-[3-(dimethylamino)propyl] methacrylamide) and in hydration state (both swollen and dried states). Formation of craters is the dominant morphological change observed by ablation in the visible at 532 nm, whereas additional, less aggressive surface modifications, chiefly microfoams and roughness, are developed in the ultraviolet at 266 nm. At both irradiation wavelengths, threshold values of the incident laser fluence for the observation of the various surface modifications are determined under single-pulse laser irradiation conditions. It is shown that multiple-pulse irradiation at 266 nm with a limited number of laser shots can be used alternatively for generating a regular microfoam layer at the surface of dried hydrogels based on N,N-dimethylaminoethyl methacrylate. The observations are rationalized on the basis of currently accepted mechanisms for laser-induced polymer surface modification, with a significant contribution of the laser foaming mechanism. Prospective applications of the laser-foamed hydrogel matrices in biomolecule immobilization are suggested.

  12. Comet 67P's morphological dichotomy and surface evolution from the Rosetta/OSIRIS camera

    Science.gov (United States)

    Ramy El-Maarry, M.; Thomas, Nicolas; Gracia-Berná, Antonio; Pajola, Maurizio; Groussin, Olivier; ROSETTA/OSIRIS

    2016-10-01

    The Rosetta mission orbited comet 67P/Churyumov-Gerasimenko from Aug, 2014 to Sep, 2016. During this time, it obtained the most comprehensive image dataset for a comet's nucleus in terms of resolution, as well as spatial and temporal coverage, using the OSIRIS camera. These images have shown the surface of the comet to be very diverse in its texture and geology. In particular, the 2-year duration of the mission permitted imaging of both hemispheres and the possibility to assess the morphology and surface evolution of comet's 67P's northern hemisphere before and after perihelion passage (in Aug, 2015). The northern hemisphere (NH) is morphologically diverse including regions of consolidated, often fractured materials, smooth terrains showing aeolian-like landforms and seasonal variations, dust-covered areas suggestive of an air-fall-like mechanism, and irregular large-scale depressions suggestive of massive outburst activities. On the other hand, the southern hemisphere (SH) shows a clear dichotomy with the North showing regionally rougher terrains with little or no smooth deposits. Similarly, dusty coatings that were observed in the northern hemisphere are generally lacking in addition to the absence of large depressions. Overall, the SH shows significantly less topographical variation in comparison to the NH. The difference in relief between the NH and SH may be explained by the differences in erosional extent between both hemispheres. The SH has a shorter yet more intensive summer (close to perihelion), which could result in levels of erosion in the SH that are up to a factor of 3 higher than that of the NH. Another notable difference between both hemispheres is the absence of smooth deposits and dust coatings in the SH. The absence of similar deposits in the south may suggest that activity in the SH occurs with much higher intensity leading to ejection of dust particles at velocities exceeding comet's escape velocity. During the meeting, we plan to summarize the

  13. Water-induced morphology changes in an ultrathin silver film studied by ultraviolet-visible, surface-enhanced Raman scattering spectroscopy and atomic force microscopy

    International Nuclear Information System (INIS)

    Li Xiaoling; Xu Weiqing; Jia Huiying; Wang Xu; Zhao Bing; Li Bofu; Ozaki, Yukihiro

    2005-01-01

    Water-induced changes in the morphology and optical properties of an ultrathin Ag film (3 nm thickness) have been studied by use of ultraviolet-visible (UV-Vis) spectroscopy, atomic force microscopy (AFM) and surface-enhanced Raman scattering (SERS) spectroscopy. A confocal micrograph shows that infinite regular Ag rings with almost uniform size (4 μm) emerge on the film surface after the ultrathin Ag film was immersed into water. The AFM measurement further confirms that the Ag rings consist of some metal holes with pillared edges. The UV-Vis spectrum shows that an absorption band at 486 nm of the Ag film after the immersion in water (I-Ag film) blue shifts by 66 nm with a significant decrease in absorbance, which is attributed to the macroscopic loss of some Ag atoms and the change in the morphology of the Ag film. The polarized UV-Vis spectra show that a band at 421 nm due to the normal component of the plasmon oscillation blue shifts after immersing the ultrathin Ag film into water. This band is found to be strongly angle-dependent for p-polarized light, indicating that the optical properties of the ultrathin Ag film are changed. The I-Ag film is SERS-active, and the SERS enhancement depends on different active sites on the film surface. Furthermore, it seems that the orientation of an adsorbate is related to the morphology of the I-Ag film

  14. Probing cluster surface morphology by cryo spectroscopy of N2 on cationic nickel clusters

    Science.gov (United States)

    Dillinger, Sebastian; Mohrbach, Jennifer; Niedner-Schatteburg, Gereon

    2017-11-01

    We present the cryogenic (26 K) IR spectra of selected [Nin(N2)m]+ (n = 5-20, m = 1 - mmax), which strongly reveal n- and m-dependent features in the N2 stretching region, in conjunction with density functional theory modeling of some of these findings. The observed spectral features allow us to refine the kinetic classification [cf. J. Mohrbach, S. Dillinger, and G. Niedner-Schatteburg, J. Chem. Phys. 147, 184304 (2017)] and to define four classes of structure related surface adsorption behavior: Class (1) of Ni6+, Ni13+, and Ni19+ are highly symmetrical clusters with all smooth surfaces of equally coordinated Ni atoms that entertain stepwise N2 adsorption up to stoichiometric N2:Nisurface saturation. Class (2) of Ni12+ and Ni18+ are highly symmetrical clusters minus one. Their relaxed smooth surfaces reorganize by enhanced N2 uptake toward some low coordinated Ni surface atoms with double N2 occupation. Class (3) of Ni5+ and Ni7+ through Ni11+ are small clusters of rough surfaces with low coordinated Ni surface atoms, and some reveal semi-internal Ni atoms of high next-neighbor coordination. Surface reorganization upon N2 uptake turns rough into rough surface by Ni atom migration and turns octahedral based structures into pentagonal bipyramidal structures. Class (4) of Ni14+ through Ni17+ and Ni20+ are large clusters with rough and smooth surface areas. They possess smooth icosahedral surfaces with some proximate capping atom(s) on one hemisphere of the icosahedron with the other one largely unaffected.

  15. Morphological and animal study of titanium dental implant surface induced by blasting and high intensity pulsed Nd-glass laser

    Energy Technology Data Exchange (ETDEWEB)

    Karacs, A.; Joob Fancsaly, A.; Divinyi, T.; Peto, G.; Kovach, G

    2003-03-03

    Machined dental implants of titanium were blasted with Al{sub 2}O{sub 3} powder of 250 {mu}m particle size. The surface was irradiated in vacuum with a Nd-glass pulsed laser at 1-3 J pulse energies. The morphology of these surfaces was investigated by optical and scanning electron microscopy. The low intensity laser treatment resulted in some new irregularities but we can observe the blasted elements and caves from the original blasted surface too. The blasted elements were washed out and a new surface morphology was induced by the high intensity laser treatment. The osseointegration was determined by measuring the removal torque in the rabbit experiments. The results were referred to the as machined surface. The blasting slightly increased the removal torque. The laser irradiation increased the removal torque significantly, more by a factor of 1.5 compared to the reference at high laser intensity. This shows the influence of the surface morphology on the osseointegration. The combination of the blasting with the laser irradiation is considered a method to determine the morphology optimal for the osseointegration because the pulsed laser irradiation caused modifications of the micrometer sized surface elements and decreases possible surface contamination.

  16. Morphological and animal study of titanium dental implant surface induced by blasting and high intensity pulsed Nd-glass laser

    International Nuclear Information System (INIS)

    Karacs, A.; Joob Fancsaly, A.; Divinyi, T.; Peto, G.; Kovach, G.

    2003-01-01

    Machined dental implants of titanium were blasted with Al 2 O 3 powder of 250 μm particle size. The surface was irradiated in vacuum with a Nd-glass pulsed laser at 1-3 J pulse energies. The morphology of these surfaces was investigated by optical and scanning electron microscopy. The low intensity laser treatment resulted in some new irregularities but we can observe the blasted elements and caves from the original blasted surface too. The blasted elements were washed out and a new surface morphology was induced by the high intensity laser treatment. The osseointegration was determined by measuring the removal torque in the rabbit experiments. The results were referred to the as machined surface. The blasting slightly increased the removal torque. The laser irradiation increased the removal torque significantly, more by a factor of 1.5 compared to the reference at high laser intensity. This shows the influence of the surface morphology on the osseointegration. The combination of the blasting with the laser irradiation is considered a method to determine the morphology optimal for the osseointegration because the pulsed laser irradiation caused modifications of the micrometer sized surface elements and decreases possible surface contamination

  17. Transparent thin films of indium tin oxide: Morphology-optical investigations, inter dependence analyzes

    Science.gov (United States)

    Prepelita, P.; Filipescu, M.; Stavarache, I.; Garoi, F.; Craciun, D.

    2017-12-01

    Using a fast and eco-friendly deposition method, ITO thin films with different thicknesses (0.5 μm-0.7 μm) were deposited on glass substrates by radio frequency magnetron sputtering technique. A comparative analysis of these oxide films was then carried out. AFM investigations showed that the deposited films were smooth, uniform and having a surface roughness smaller than 10 nm. X-ray diffraction investigations showed that all samples were polycrystalline and the grain sizes of the films, corresponding to (222) cubic reflection, were found to increase with the increasing film thickness. The optical properties, evaluated by UV-VIS-NIR (190-3000 nm) spectrophotometer, evidenced that the obtained thin films were highly transparent, with a transmission coefficient between 90 and 96%, depending on the film thickness. Various methods (Swanepoel and Drude) were employed to appreciate the optimal behaviour of transparent oxide films, in determining the dielectric optical parameters and refractive index dispersion for ITO films exhibiting interference patterns in the optical transmission spectra. The electrical conductivity also increased as the film thickness increased.

  18. Tailoring the morphology of raspberry-like carbon black/polystyrene composite microspheres for fabricating superhydrophobic surface

    International Nuclear Information System (INIS)

    Bao, Yubin; Li, Qiuying; Xue, Pengfei; Huang, Jianfeng; Wang, Jibin; Guo, Weihong; Wu, Chifei

    2011-01-01

    In our previous report, raspberry-like carbon black/polystyrene (CB/PS) composite microsphere was prepared through heterocoagulation process. Based on the previous study, in the present work, the morphology of raspberry-like CB/PS particle is tailored through adjusting the polarity and the concentration ratio of CB/PS colloidal suspension with the purpose to prepare particulate film for the fabrication of superhydrophobic surface. Scanning electron microscope (SEM) confirms the morphology of raspberry-like particle and the coverage of CB. Rough surfaces fabricated by raspberry-like particles with proper morphology are observed by SEM and clear evidence of superhydrophobic surface is shown. The structure of raspberry-like particle is analyzed by atom force microscope. The proposed relationship between the hydrophobicity and the structure of CB aggregates on the surface of PS microsphere is discussed in details.

  19. Morphology Dependent Flow Stress in Nickel-Based Superalloys in the Multi-Scale Crystal Plasticity Framework

    Directory of Open Access Journals (Sweden)

    Shahriyar Keshavarz

    2017-11-01

    Full Text Available This paper develops a framework to obtain the flow stress of nickel-based superalloys as a function of γ-γ’ morphology. The yield strength is a major factor in the design of these alloys. This work provides additional effects of γ’ morphology in the design scope that has been adopted for the model developed by authors. In general, the two-phase γ-γ’ morphology in nickel-based superalloys can be divided into three variables including γ’ shape, γ’ volume fraction and γ’ size in the sub-grain microstructure. In order to obtain the flow stress, non-Schmid crystal plasticity constitutive models at two length scales are employed and bridged through a homogenized multi-scale framework. The multi-scale framework includes two sub-grain and homogenized grain scales. For the sub-grain scale, a size-dependent, dislocation-density-based finite element model (FEM of the representative volume element (RVE with explicit depiction of the γ-γ’ morphology is developed as a building block for the homogenization. For the next scale, an activation-energy-based crystal plasticity model is developed for the homogenized single crystal of Ni-based superalloys. The constitutive models address the thermo-mechanical behavior of nickel-based superalloys for a large temperature range and include orientation dependencies and tension-compression asymmetry. This homogenized model is used to obtain the morphology dependence on the flow stress in nickel-based superalloys and can significantly expedite crystal plasticity FE simulations in polycrystalline microstructures, as well as higher scale FE models in order to cast and design superalloys.

  20. Study of structure and surface morphology of two-layer contact Ti/Al metallization

    Directory of Open Access Journals (Sweden)

    Kirill D. Vanyukhin

    2016-06-01

    Full Text Available Ti/Al/Ni/Au metallization widely used in the technology of GaN base devices have a very important imperfection i.e. rough surface. There are different opinions about the causes of this imperfection: balling-up of molten aluminum or the appearance of intermetallic melt phases in the Au–Al system. To check the effect of the former cause, we have studied the formation of rough surface after annealing of Ti/Al metallization which is used as a basis of many metallization systems for GaN. The substrates were made from silicon wafers covered with Si3N4 films (0.15 μm. On these substrates we deposited the Ti(12 nm/Al(135 nm metallization system. After the deposition the substrates were annealed in nitrogen for 30 s at 850 °С. The as-annealed specimens were tested for metallization sheet resistivity, appearance and surface morphology. We have shown that during annealing of the Ti/Al metallization system, mutual diffusion of the metals and their active interaction with the formation of intermetallic phases occur. This makes the metallization system more resistant to subsequent annealing, oxidation and chemical etching. After annealing the surface of the Ti/Al metallization system becomes gently matted. However, large hemispherical convex areas (as in the Ti/Al/Ni/Au metallization system do not form. Thus, the hypothesis on the balling-up of molten aluminum on the surface of the Ti/Al metallization system has not been confirmed.

  1. Effects of acid treatment on the clay palygorskite: XRD, surface area, morphological and chemical composition

    Energy Technology Data Exchange (ETDEWEB)

    Xavier, Katiane Cruz Magalhaes; Santos, Maria do Socorro Ferreira dos; Santos, Maria Rita Morais Chaves; Oliveira, Marilia Evelyn Rodrigues; Osajima, Josy Antevelli; Silva Filho, Edson Cavalcanti da [Universidade Federal do Piaui (UFPI), Teresina, PI (Brazil); Carvalho, Maria Wilma Nunes Cordeiro, E-mail: edsonfilho@ufpi.edu.br [Universidade Federal de Campina Grande (UFCG), PB (Brazil)

    2014-08-15

    The palygorskite is an aluminum-magnesium silicate that has a fibrous morphology. Their physicochemical characteristics are the result of high surface area, porosity and thermal resistance which make it an attractive adsorbent. Its adsorption capacity can be increased through chemical reactions and/or heat treatments. The objective of this work is to verify the effects of acid activation on the palygorskite, treated with HCl at 90 °C at concentrations of 2, 4 and 6 mol L{sup -1} in 2 and 4 hours, with clay/acid solution ratio 1 g 10 mL{sup -1} and characterized by techniques: XRF, XRD and surface area. A significant increase in specific surface area was observed in the sample treated with HCl at the concentration 6 mol L{sup -1}. The changes were more pronounced at stricter concentrations of acidity, with decreasing intensity of reflection of the clay indicated in the XRD. These changes were confirmed in the XRF with the leaching of some oxides and with increasing concentration of SiO{sub 2}. (author)

  2. Surfaces wettability and morphology modulation in a fluorene derivative self-assembly system

    Energy Technology Data Exchange (ETDEWEB)

    Cao, Xinhua, E-mail: caoxhchem@163.com; Gao, Aiping; Zhao, Na; Yuan, Fangyuan; Liu, Chenxi; Li, Ruru

    2016-04-15

    Graphical abstract: - Highlights: • The different structures could be obtained in this self-assembly system. • A water-drop could freely roll on the xerogel film with the sliding angle of 15.0. • The superhydrophobic surface can be obtained via supramolecular self-assembly. - Abstract: A new organogelator based on fluorene derivative (gelator 1) was designed and synthesized. Organogels could be obtained via the self-assembly of the derivative in acetone, toluene, ethyl acetate, hexane, DMSO and petroleum ether. The self-assembly process was thoroughly characterized using field-emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), UV–vis, FT-IR and the contact angle. Surfaces with different morphologies and wetting properties were formed via the self-assembly of gelator 1 in the six different solvents. Interestingly, a superhydrophobic surface with a contact angle of 150° was obtained from organogel 1 in DMSO and exhibited the lotus-effect. The sliding angle necessary for a water droplet to move on the glass was only 15°. Hydrogen bonding and van der Waals forces were attributed as the main driving forces for gel formation.

  3. Fracture Surface Morphology and Impact Strength of Cellulose/PLA Composites.

    Science.gov (United States)

    Gao, Honghong; Qiang, Tao

    2017-06-07

    Polylactide (PLA)-based composite materials reinforced with ball-milled celluloses were manufactured by extrusion blending followed by injection molding. Their surface morphology from impact fracture were imaged with scanning electron microscopy (SEM) and investigated by calculating their fractal dimensions. Then, linear regression was used to explore the relationship between fractal dimension and impact strength of the resultant cellulose/PLA composite materials. The results show that filling the ball-milled celluloses into PLA can improve the impact toughness of PLA by a minimum of 38%. It was demonstrated that the fracture pattern of the cellulose/PLA composite materials is different from that of pristine PLA. For the resultant composite materials, the fractal dimension of the impact fractured surfaces increased with increasing filling content and decreasing particle size of the ball-milled cellulose particles. There were highly positive correlations between fractal dimension of the fractured surfaces and impact strength of the cellulose/PLA composites. However, the linearity between fractal dimension and impact strength were different for the different methods, due to their different R-squared values. The approach presented in this work will help to understand the structure-property relationships of composite materials from a new perspective.

  4. Surface morphology evolution of amorphous Fe-Si layers upon thermal annealing

    Energy Technology Data Exchange (ETDEWEB)

    Sun, C M; Tsang, H K; Wong, S P; Ke, N [Department of Electronic Engineering, Chinese University of Hong Kong, Shatin, NT, Hong Kong (China); Hark, S K [Department of Physics, Chinese University of Hong Kong, Shatin, NT, Hong Kong (China)], E-mail: cmsun@ee.cuhk.edu.hk

    2008-04-21

    Changes in the surface morphology of ion-beam-synthesized amorphous Fe-Si layers after rapid thermal annealing (RTA) and furnace annealing (FA) were investigated using atomic force microscopy and transmission electron microscopy. Completely amorphous Fe-Si layers were formed by Fe implantation at a dosage of 5 x 10{sup 15} cm{sup -2} using a metal vapour vacuum arc ion source under 80 kV extraction voltage and cryogenic temperature. After RTA at 850 deg. C, {beta}-FeSi{sub 2} precipitates in Si are completely aggregated from this amorphous Fe-Si layer and the surface of the implanted layer remains flat. To date, no obvious photoluminescence (PL) spectrum has been reported from RTA treated {beta}-FeSi{sub 2} precipitates. However, after annealing at 850 deg. C for 40 s, high-quality {beta}-FeSi{sub 2} precipitates in Si are obtained which clearly show 1.5 {mu}m PL at 80 K for the first time. Even though additional long-term FA at 850 deg. C can enhance PL intensity to a limited extent, the longer thermal treatment induces the outdiffusion of {beta}-FeSi{sub 2} precipitates and degrades the surface flatness.

  5. Differential scanning calorimetry and surface morphology studies on coated pellets using aqueous dispersions.

    Science.gov (United States)

    Nisar-ur-Rahman; K H, Yuen; Jia Woei, Wong; Khan, Nurzalina A k

    2005-04-01

    The present study was conducted to examine the physicochemical changes during passage of drug through polymeric membranes and observe the surface morphology features of the coated pellets using scanning electron microscopy (SEM). Drug solution was first sprayed around inert pellets to form drug-layered pellets that were coated with two commercial aqueous dispersions namely, Eudragit NE30 and Kollicoat SR30 using bottom-spray fluidized bed technique. Differential scanning calorimetry (DSC) confirmed that no interactions existed between drug and polymers. Small peak of drug was observed in the DSC thermograms of Eudragit NE30 coated pellets indicating that small amount of drug was still present in the polymeric membrane after dissolution. Views of SEM revealed as the coating levels of two types of aqueous dispersions were increased the surface of the pellets become more uniform and compact. Therefore, the diffusion length for dissolution medium to enter the drug layer and dissolved drug to diffuse out would be increased at higher coating levels. The polymer surface of coated pellets after 12 hours dissolution testing seemed to be shrunk and size of the pellets were also reduced indicating the depletion of reservoir layer.

  6. Gum ghatti based novel electrically conductive biomaterials: A study of conductivity and surface morphology

    Directory of Open Access Journals (Sweden)

    S. Kalia

    2014-04-01

    Full Text Available Gum ghatti-cl-poly(acrylamide-aniline interpenetrating network (IPN was synthesized by a two-step aqueous polymerization method, in which aniline monomer was absorbed into the network of gum ghatti-cl-poly(acrylamide and followed by a polymerization reaction between aniline monomers. Initially, semi-IPN based on acrylamide and gum ghatti was prepared by free-radical copolymerization in aqueous media with optimized process parameters, using N,N'-methylenebis-acrylamide, as cross-linker and ammonium persulfate, as an initiator system. Optimum reaction conditions affording maximum percentage swelling were: solvent [mL] =12, Acrylamide (AAm [mol•L–1] = 1.971, Ammonium peroxydisulfate (APS [mol•L–1] = 0.131•10–1, N,N'-methylene-bis-acrylamide (MBA [mol•L–1] = 0.162•10–1, reaction time [min] = 210, temperature [°C] = 100 and pH = 7.0. The resulting IPN was doped with different protonic acids. The effect of the doping has been investigated on the conductivity and surface morphology of the IPN hydrogel. The maximum conductivity was observed with 1.5N HClO4 concentration. The morphological, structural and electrical properties of the candidate polymers were studied using scanning electron micrscopy (SEM, Fourier transform infrared spectroscopy FTIR and two-probe method, respectively.

  7. Prediction Surface Morphology of Nanostructure Fabricated by Nano-Oxidation Technology.

    Science.gov (United States)

    Huang, Jen-Ching; Chang, Ho; Kuo, Chin-Guo; Li, Jeen-Fong; You, Yong-Chin

    2015-12-04

    Atomic force microscopy (AFM) was used for visualization of a nano-oxidation technique performed on diamond-like carbon (DLC) thin film. Experiments of the nano-oxidation technique of the DLC thin film include those on nano-oxidation points and nano-oxidation lines. The feature sizes of the DLC thin film, including surface morphology, depth, and width, were explored after application of a nano-oxidation technique to the DLC thin film under different process parameters. A databank for process parameters and feature sizes of thin films was then established, and multiple regression analysis (MRA) and a back-propagation neural network (BPN) were used to carry out the algorithm. The algorithmic results are compared with the feature sizes acquired from experiments, thus obtaining a prediction model of the nano-oxidation technique of the DLC thin film. The comparative results show that the prediction accuracy of BPN is superior to that of MRA. When the BPN algorithm is used to predict nano-point machining, the mean absolute percentage errors (MAPE) of depth, left side, and right side are 8.02%, 9.68%, and 7.34%, respectively. When nano-line machining is being predicted, the MAPEs of depth, left side, and right side are 4.96%, 8.09%, and 6.77%, respectively. The obtained data can also be used to predict cross-sectional morphology in the DLC thin film treated with a nano-oxidation process.

  8. Nanoscale protein arrays of rich morphologies via self-assembly on chemically treated diblock copolymer surfaces

    International Nuclear Information System (INIS)

    Song Sheng; Milchak, Marissa; Zhou Hebing; Lee, Thomas; Hanscom, Mark; Hahm, Jong-in

    2013-01-01

    Well-controlled assembly of proteins on supramolecular templates of block copolymers can be extremely useful for high-throughput biodetection. We report the adsorption and assembly characteristics of a model antibody protein to various polystyrene-block-poly(4-vinylpyridine) templates whose distinctive nanoscale structures are obtained through time-regulated exposure to chloroform vapor. The strong adsorption preference of the protein to the polystyrene segment in the diblock copolymer templates leads to an easily predictable, controllable, rich set of nanoscale protein morphologies through self-assembly. We also demonstrate that the chemical identities of various subareas within individual nanostructures can be readily elucidated by investigating the corresponding protein adsorption behavior on each chemically distinct area of the template. In our approach, a rich set of intricate nanoscale morphologies of protein arrays that cannot be easily attained through other means can be generated straightforwardly via self-assembly of proteins on chemically treated diblock copolymer surfaces, without the use of clean-room-based fabrication tools. Our approach provides much-needed flexibility and versatility for the use of block copolymer-based protein arrays in biodetection. The ease of fabrication in producing well-defined and self-assembled templates can contribute to a high degree of versatility and simplicity in acquiring an intricate nanoscale geometry and spatial distribution of proteins in arrays. These advantages can be extremely beneficial both for fundamental research and biomedical detection, especially in the areas of solid-state-based, high-throughput protein sensing. (paper)

  9. Colour interceptions, thermal stability and surface morphology of polyester metal complexes

    International Nuclear Information System (INIS)

    Zohdy, M.H.

    2005-01-01

    Chelating copolymers via grafting of acrylic acid (AAc) and acrylamide (AAm/AAc) comonomer mixture onto polyester micro fiber fabrics (PETMF) using gamma-radiation technique were prepared. The prepared graft chains (PETMF-g-AAc) and (PETMF-g-PAAc/PAAm) acted as chelating sites for some selected transition metal ions. The prepared graft copolymers and their metal complexes were characterized using thermogravimetric analysis (TGA), colour parameters and surface morphology measurements. The colour interception and strength measurements showed that the metal complexation is homogeneously distributed. The results showed that the thermal stability of PETMF was improved after graft copolymerization and metal complexes. Moreover, the degree of grafting enhanced the thermal stability values of the grafted and complexed copolymers up to 25% of magnitude, on the other hand the activation energy of the grafted-copolymer with acrylic acid increased up to 80%. The SEM observation gives further supports to the homogenous distribution of grafting and metal complexation

  10. Structural Color Model Based on Surface Morphology of MORPHO Butterfly Wing Scale

    Science.gov (United States)

    Huang, Zhongjia; Cai, Congcong; Wang, Gang; Zhang, Hui; Huttula, Marko; Cao, Wei

    2016-05-01

    Color production through structural coloration is created by micrometer and sub-micrometer surface textures which interfere with visible light. The shiny blue of morpho menelaus is a typical example of structural coloring. Modified from morphology of the morpho scale, a structure of regular windows with two side offsets was constructed on glass substrates. Optical properties of the bioinspired structure were studied through numerical simulations of light scattering. Results show that the structure can generate monochromatic light scattering. Wavelength of scattered light is tunable via changing the spacing between window shelves. Compared to original butterfly model, the modified one possesses larger illumination scopes in azimuthal distributions despite being less in polar directions. Present bionic structure is periodically repeated and is easy to fabricate. It is hoped that the computational materials design work can inspire future experimental realizations of such a structure in photonics applications.

  11. Monitoring of temperature profiles and surface morphologies during laser sintering of alumina ceramics

    Directory of Open Access Journals (Sweden)

    Bin Qian

    2014-06-01

    Full Text Available Additive manufacturing of alumina by laser is a delicate process and small changes of processing parameters might cause less controlled and understood consequences. The real-time monitoring of temperature profiles, spectrum profiles and surface morphologies were evaluated in off-axial set-up for controlling the laser sintering of alumina ceramics. The real-time spectrometer and pyrometer were used for rapid monitoring of the thermal stability during the laser sintering process. An active illumination imaging system successfully recorded the high temperature melt pool and surrounding area simultaneously. The captured images also showed how the defects form and progress during the laser sintering process. All of these real-time monitoring methods have shown a great potential for on-line quality control during laser sintering of ceramics.

  12. Improving Morphological Quality and Uniformity of Hydrothermally Grown ZnO Nanowires by Surface Activation of Catalyst Layer.

    Science.gov (United States)

    Murillo, Gonzalo; Lozano, Helena; Cases-Utrera, Joana; Lee, Minbaek; Esteve, Jaume

    2017-12-01

    This paper presents a study about the dependence of the hydrothermal growth of ZnO nanowires (NWs) with the passivation level of the active surface of the Au catalyst layer. The hydrothermal method has many potential applications because of its low processing temperature, feasibility, and low cost. However, when a gold thin film is utilized as the seed material, the grown NWs often lack morphological homogeneity; their distribution is not uniform and the reproducibility of the growth is low. We hypothesize that the state or condition of the active surface of the Au catalyst layer has a critical effect on the uniformity of the NWs. Inspired by traditional electrochemistry experiments, in which Au electrodes are typically activated before the measurements, we demonstrate that such activation is a simple way to effectively assist and enhance NW growth. In addition, several cleaning processes are examined to find one that yields NWs with optimal quality, density, and vertical alignment. We find cyclic voltammetry measurements to be a reliable indicator of the seed-layer quality for subsequent NW growth. Therefore, we propose the use of this technique as a standard procedure prior to the hydrothermal synthesis of ZnO NWs to control the growth reproducibility and to allow high-yield wafer-level processing.

  13. Cu/ZnO nanocatalysts in response to environmental conditions: surface morphology, electronic structure, redox state and CO2 activation.

    Science.gov (United States)

    Martínez-Suárez, Luis; Frenzel, Johannes; Marx, Dominik

    2014-12-21

    Methanol synthesis is one of the landmarks of heterogeneous catalysis due to the great industrial significance of methanol as a clean liquid fuel and as a raw material for industry. Understanding in atomistic detail the properties of the underlying metal/oxide catalyst materials as a function of temperature and composition of the reactive gas phase is of utmost importance in order to eventually improve the production process. By performing extensive density functional theory based slab calculations in combination with a thermodynamic formalism we establish an atomistic understanding of gas phase-induced changes of surface morphology, redox properties and reactivity of ZnO supported Cu nanocatalysts. Extending our recent insights [Phys. Rev. Lett., 2013, 110, 086108], we explore surface stabilization mechanisms and site-dependent redox states of both catalyst components as well as the pronounced electronic charge transfer processes across the metal-support interface. Moreover, ab initio molecular dynamics simulations unveil the vital role played by dynamical shape fluctuations of the deposited Cu8 cluster. The pronounced structural flexibility of the metal nanoparticle is found to enhance CO2 activation over Cu8 at the elevated temperature conditions of the industrial methanol synthesis process, in addition to activation of CO2via electronic charge transfer from the ZnO support.

  14. Influence of surface morphology on the immersion mode ice nucleation efficiency of hematite particles

    Energy Technology Data Exchange (ETDEWEB)

    Hiranuma, N.; Hoffmann, N.; Kiselev, A.; Dreyer, A.; Zhang, K.; Kulkarni, G.; Koop, T.; Möhler, O.

    2014-01-01

    In this paper, the effect of the morphological modification of aerosol particles with respect to heterogeneous ice nucleation is comprehensively investigated for laboratory-generated hematite particles as a model substrate for atmospheric dust particles. The surface-area-scaled ice nucleation efficiencies of monodisperse cubic hematite particles and milled hematite particles were measured with a series of expansion cooling experiments using the Aerosol Interaction and Dynamics in the Atmosphere (AIDA) cloud simulation chamber. Complementary offline characterization of physico-chemical properties of both hematite subsets were also carried out with scanning electron microscopy (SEM), energy dispersive X-ray (EDX) spectroscopy, dynamic light scattering (DLS), and an electro-kinetic particle charge detector to further constrain droplet-freezing measurements of hematite particles. Additionally, an empirical parameterization derived from our laboratory measurements was implemented in the single-column version of the Community Atmospheric Model version 5 (CAM5) to investigate the model sensitivity in simulated ice crystal number concentration on different ice nucleation efficiencies. From an experimental perspective, our results show that the immersion mode ice nucleation efficiency of milled hematite particles is almost an order of magnitude higher at -35.2 °C < T < -33.5 °C than that of the cubic hematite particles, indicating a substantial effect of morphological irregularities on immersion mode freezing. Our modeling results similarly show that the increased droplet-freezing rates of milled hematite particles lead to about one order magnitude higher ice crystal number in the upper troposphere than cubic hematite particles. Finally and overall, our results suggest that the surface irregularities and associated active sites lead to greater ice activation through droplet freezing.

  15. Coevolution of bed surface patchiness and channel morphology: 1. Mechanisms of forced patch formation

    Science.gov (United States)

    Nelson, Peter A.; McDonald, Richard R.; Nelson, Jonathan M.; Dietrich, William E.

    2015-01-01

    Riverbeds frequently display a spatial structure where the sediment mixture composing the channel bed has been sorted into discrete patches of similar grain size. Even though patches are a fundamental feature in gravel bed rivers, we have little understanding of how patches form, evolve, and interact. Here we present a two-dimensional morphodynamic model that is used to examine in greater detail the mechanisms responsible for the development of forced bed surface patches and the coevolution of bed morphology and bed surface patchiness. The model computes the depth-averaged channel hydrodynamics, mixed-grain-size sediment transport, and bed evolution by coupling the river morphodynamic model Flow and Sediment Transport with Morphological Evolution of Channels (FaSTMECH) with a transport relation for gravel mixtures and the mixed-grain-size Exner equation using the active layer assumption. To test the model, we use it to simulate a flume experiment in which the bed developed a sequence of alternate bars and temporally and spatially persistent forced patches with a general pattern of coarse bar tops and fine pools. Cross-stream sediment flux causes sediment to be exported off of bars and imported into pools at a rate that balances downstream gradients in the streamwise sediment transport rate, allowing quasi-steady bar-pool topography to persist. The relative importance of lateral gravitational forces on the cross-stream component of sediment transport is a primary control on the amplitude of the bars. Because boundary shear stress declines as flow shoals over the bars, the lateral sediment transport is increasingly size selective and leads to the development of coarse bar tops and fine pools.

  16. A comparative study on surface morphological investigations of ferric oxide for LPG and opto-electronic humidity sensors

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Satyendra; Verma, Nidhi [Nanomaterials and Sensors Research Laboratory, Department of Physics, University of Lucknow, Lucknow 226007, U.P. (India); Yadav, B.C., E-mail: balchandra_yadav@rediffmail.com [Nanomaterials and Sensors Research Laboratory, Department of Physics, University of Lucknow, Lucknow 226007, U.P. (India); Department of Applied Physics, School for Physical Sciences, Babasaheb Bhimrao Ambedkar University, Lucknow 226025, U.P. (India); Prakash, Rajiv [School of Materials Science and Technology, Institute of Technology, Banaras Hindu University, Varanasi 221005 (India)

    2012-09-01

    Highlights: Black-Right-Pointing-Pointer Flower-like, elliptical and spherical shaped surface morphologies of Fe{sub 2}O{sub 3}. Black-Right-Pointing-Pointer The structural and surface morphological investigations. Black-Right-Pointing-Pointer The relationship between the surface morphology and sensing property. Black-Right-Pointing-Pointer Advancement in sensitivity of LPG sensor in comparison to prior work. - Abstract: In the present work nanostructured ferric oxides were synthesized via hydroxide precipitation method without using any surfactant and size selection medium. The surface morphologies and structure of samples were analyzed by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray diffraction (XRD). The structural analysis confirmed the formation of Fe{sub 2}O{sub 3} with {alpha}-phase and rhombohedral structure. Optical and thermal properties were investigated by using UV-visible absorption spectroscopy and differential scanning calorimetry (DSC) techniques. Pelletizations of materials were done using hydraulic press and these pellets were investigated with the exposition of liquefied petroleum gas. Variations in resistance of the pellet with time for different concentrations of LPG were recorded at room temperature (27 Degree-Sign C). The maximum value of average sensitivity was found {approx}5 for 5 vol.% of LPG. Our results show that the LPG sensing behavior was inspired by the different kinds of surface morphologies of Fe{sub 2}O{sub 3} and inferred that the spherical porous nanoparticles synthesized via hydroxide precipitation process (S-3) had best response to LPG.

  17. Influence of surface morphology and microstructure on performance of CVD tungsten coating under fusion transient thermal loads

    Energy Technology Data Exchange (ETDEWEB)

    Lian, Youyun, E-mail: lianyy@swip.ac.cn [Southwestern Institute of Physics, Chengdu (China); Liu, Xiang; Wang, Jianbao; Feng, Fan [Southwestern Institute of Physics, Chengdu (China); Lv, Yanwei; Song, Jiupeng [China National R& D Center for Tungsten Technology, Xiamen Tungsten Co. Ltd, 361026 Xiamen (China); Chen, Jiming [Southwestern Institute of Physics, Chengdu (China)

    2016-12-30

    Highlights: • Thick CVD-W coatingswere deposited at a rapid growth rate. • The polished CVD-W coatings have highly textured structure and exhibited a very strong preferred orientation. • The polished CVD tungsten coatings show superior thermal shock resistance as compared with that of the as-deposited coatings. • The crack formation of the polished CVD-W was almost suppressed at an elevated temperature. - Abstract: Thick tungsten coatings have been deposited by chemical vapor deposition (CVD) at a rapid growth rate. A series of tungsten coatings with different thickness and surface morphology were prepared. The surface morphology, microstructure and preferred orientation of the CVD tungsten coatings were investigated. Thermal shock analyses were performed by using an electron beam facility to study the influence of the surface morphology and the microstructure on the thermal shock resistance of the CVD tungsten coatings. Repetitive (100 pulses) ELMs-like thermal shock loads were applied at various temperatures between room temperature and 600 °C with pulse duration of 1 ms and an absorbed power density of up to 1 GW/m{sup 2}. The results of the tests demonstrated that the specific surface morphology and columnar crystal structure of the CVD tungsten have significant influence on the surface cracking threshold and crack propagation of the materials. The CVD tungsten coatings with a polished surface show superior thermal shock resistance as compared with that of the as-deposited coatings with a rough surface.

  18. Syndecan-2 regulation of morphology in breast carcinoma cells is dependent on RhoGTPases

    DEFF Research Database (Denmark)

    Lim, Hooi Ching; Couchman, John Robert

    2014-01-01

    While syndecan-2 is usually considered a mesenchymal transmembrane proteoglycan, it can be upregulated in some tumour cells, such as the malignant breast carcinoma cell line, MDA-MB231. Depletion of this syndecan by siRNA, but not other syndecans, has a marked effect on cell morphology, increasin...... spreading, microfilament bundle and focal adhesion formation, with reduced cell migration....

  19. Time Dependent Assessment of Morphological Changes: Leukodepleted Packed Red Blood Cells Stored in SAGM

    Directory of Open Access Journals (Sweden)

    Ibrahim Mustafa

    2016-01-01

    Full Text Available Usually packed red blood cells (pRBCs require specific conditions in storage procedures to ensure the maximum shelf life of up to 42 days in 2–6°C. However, molecular and biochemical consequences can affect the stored blood cells; these changes are collectively labeled as storage lesions. In this study, the effect of prolonged storage was assessed through investigating morphological changes and evaluating oxidative stress. Samples from leukodepleted pRBC in SAGM stored at 4°C for 42 days were withdrawn aseptically on day 0, day 14, day 28, and day 42. Morphological changes were observed using scanning electron microscopy and correlated with osmotic fragility and hematocrit. Oxidative injury was studied through assessing MDA level as a marker for lipid peroxidation. Osmotic fragility test showed that extended storage time caused increase in the osmotic fragility. The hematocrit increased by 6.6% from day 0 to day 42. The last 2 weeks show alteration in the morphology with the appearance of echinocytes and spherocytes. Storage lesions and morphological alterations appeared to affect RBCs during the storage period. Further studies should be performed to develop strategies that will aid in the improvement of stored pRBC quality and efficacy.

  20. Rate-Dependent Slip of Newtonian Liquid at Smooth Surfaces

    International Nuclear Information System (INIS)

    Zhu, Yingxi; Granick, Steve

    2001-01-01

    Newtonian fluids were placed between molecularly smooth surfaces whose spacing was vibrated at spacings where the fluid responded as a continuum. Hydrodynamic forces agreed with predictions from the no-slip boundary condition only provided that flow rate (peak velocity normalized by spacing) was low, but implied partial slip when it exceeded a critical level, different in different systems, correlated with contact angle (surface wettability). With increasing flow rate and partially wetted surfaces, hydrodynamic forces became up to 2--4 orders of magnitude less than expected by assuming the no-slip boundary condition that is commonly stated in textbooks

  1. Study of surfaces and morphologies of proteic sol–gel derived barium aluminate nanopowders: An experimental and computational study

    International Nuclear Information System (INIS)

    Rezende, M.V. dos S.; Arrouvel, C.; Parker, S.C.; Rey, J.F.Q.; Valerio, M.E.G.

    2012-01-01

    BaAl 2 O 4 nanoparticles samples were prepared by sol–gel proteic route. The preparation of the precursor mixture and the formation of the ceramic product were monitored using TG/DTA, X-ray diffraction (XRD), electron microscopy (SEM, TEM). The results show that sol–gel proteic route is a reliable method for the synthesis of pure BaAl 2 O 4 powders and that irregular hexagonal facetted nanoparticles are observed. Atomistic modeling was used to calculate the structures and energies of 24 (hkl) surfaces and to evaluate morphologies of BaAl 2 O 4 at the thermodynamic and pseudo-kinetic equilibrium. The calculations show that the two most stable surfaces are the (001) and (011) with a surface energy of 1.33 J m −2 and 1.36 J m −2 respectively and that the predicted morphologies are in accord with experiment. -- Highlights: ► Experimental and atomistic simulation techniques to study surfaces and morphologies of pure hexagonal BaAl 2 O 4 phase. ► The irregular hexagonal facetted nanoparticles are observed. ► The kinetic morphology is elongated with a hexagonal termination. ► The most stable surfaces are the (001) and (011) with a surface energy of 1.33 J m −2 .

  2. Surface morphology and chemical composition of TiTa-based surface alloy formed on TiNi by electron beam additive technologies

    Science.gov (United States)

    Gudimova, E. Yu.; Meisner, L. L.; Meisner, S. N.; Yakovlev, E. V.; Shabalina, O. I.

    2017-12-01

    This paper presents research results on the physiochemical and topographic surface properties of a NiTi alloy and their changes after different surface treatments: mechanical polishing, electron beam cleaning, and TiTa-based surface alloying. The possibility of using electron beam treatment for surface preparation with no additional methods is shown. Experiments demonstrate that the TiTa-based alloy surface formed by multiple magnetron deposition of TiTa film and subsequent pulsed electron beam melting of the film/substrate system is chemically and morphologically homogeneous.

  3. Synthesis of Mn3O4 nanoparticles via a facile gel formation route and study of their phase and structural transformation with distinct surface morphology upon heat treatment

    Directory of Open Access Journals (Sweden)

    A.K.M. Atique Ullah

    2017-11-01

    Full Text Available Mn3O4 nanoparticles (NPs were synthesized from the reduction of KMnO4 with glycerol at 80 °C in aqueous media via a gel formation route. In order to investigate the thermal stability and phase transformation, Mn3O4 NPs were subjected to heat treatment from 200 °C to 700 °C. The formation of different MnOx species observed by X-ray diffraction (XRD measurements showed temperature dependent phase transformation occurring during the heat treatment process. XRD patterns showed that Mn3O4 NPs were formed at a temperature of 80 °C and two new phases Mn5O8 and Mn2O3 were appeared at 350 °C and 700 °C respectively. The three different oxides having their distinct surface morphologies viz., spherical, rod and cube shape respectively, were observed. Detailed morphological and structural investigations using Field Emission Scanning Electron Microscopy (FESEM, XRD, Thermo Gravimetric Analysis (TGA and Differential Scanning Calorimetry (DSC revealed the temperature dependent phases, crystal structures, lattice constants, particle sizes and surface morphologies of the MnOx species.

  4. Surface Morphology and Growth of Anodic Titania Nanotubes Films: Photoelectrochemical Water Splitting Studies

    Directory of Open Access Journals (Sweden)

    Chin Wei Lai

    2015-01-01

    become the most studied material as they exhibit promising functional properties. In the present study, anodic TiO2 films with different surface morphologies can be synthesized in an organic electrolyte of ethylene glycol (EG by controlling an optimum content of ammonium fluoride (NH4F using electrochemical anodization technique. Based on the results obtained, well-aligned and bundle-free TiO2 nanotube arrays with diameter of 100 nm and length of 8 µm were successfully synthesized in EG electrolyte containing ≈5 wt% of NH4F for 1 h at 60 V. However, formation of nanoporous structure and compact oxide layer would be favored if the content of NH4F was less than 5 wt%. In the photoelectrochemical (PEC water splitting studies, well-aligned TiO2 nanotubular structure exhibited higher photocurrent density of ≈1 mA/cm2 with photoconversion efficiency of ≈2% as compared to the nanoporous and compact oxide layer due to the higher active surface area for the photon absorption to generate more photo-induced electrons during photoexcitation stage.

  5. Seed set, pollen morphology and pollen surface composition response to heat stress in field pea.

    Science.gov (United States)

    Jiang, Yunfei; Lahlali, Rachid; Karunakaran, Chithra; Kumar, Saroj; Davis, Arthur R; Bueckert, Rosalind A

    2015-11-01

    Pea (Pisum sativum L.) is a major legume crop grown in a semi-arid climate in Western Canada, where heat stress affects pollination, seed set and yield. Seed set and pod growth characteristics, along with in vitro percentage pollen germination, pollen tube growth and pollen surface composition, were measured in two pea cultivars (CDC Golden and CDC Sage) subjected to five maximum temperature regimes ranging from 24 to 36 °C. Heat stress reduced percentage pollen germination, pollen tube length, pod length, seed number per pod, and the seed-ovule ratio. Percentage pollen germination of CDC Sage was greater than CDC Golden at 36 °C. No visible morphological differences in pollen grains or the pollen surface were observed between the heat and control-treated pea. However, pollen wall (intine) thickness increased due to heat stress. Mid-infrared attenuated total reflectance (MIR-ATR) spectra revealed that the chemical composition (lipid, proteins and carbohydrates) of each cultivar's pollen grains responded differently to heat stress. The lipid region of the pollen coat and exine of CDC Sage was more stable compared with CDC Golden at 36 °C. Secondary derivatives of ATR spectra indicated the presence of two lipid types, with different amounts present in pollen grains from each cultivar. © 2015 John Wiley & Sons Ltd.

  6. Growth and morphology of sputtered aluminum thin films on P3HT surfaces.

    Science.gov (United States)

    Kaune, Gunar; Metwalli, Ezzeldin; Meier, Robert; Körstgens, Volker; Schlage, Kai; Couet, Sebastien; Röhlsberger, Ralf; Roth, Stephan V; Müller-Buschbaum, Peter

    2011-04-01

    Growth and morphology of an aluminum (Al) contact on a poly(3-hexylthiophene) (P3HT) thin film are investigated with X-ray methods and related to the interactions at the Al:P3HT interface. Grazing incidence small-angle scattering (GISAXS) is applied in situ during Al sputter deposition to monitor the growth of the layer. A growth mode is found, in which the polymer surface is wetted and rapidly covered with a continuous layer. This growth type results in a homogeneous film without voids and is explained by the strong chemical interaction between Al and P3HT, which suppresses the formation of three-dimensional cluster structures. A corresponding three stage growth model (surface bonding, agglomeration, and layer growth) is derived. X-ray reflectivity shows the penetration of Al atoms into the P3HT film during deposition and the presence of a 2 nm thick intermixing layer at the Al:P3HT interface. © 2011 American Chemical Society

  7. Controlled synthesis of CeO2 microstructures from 1D rod-like to 3D lotus-like and their morphology-dependent properties

    Science.gov (United States)

    Gong, Jinfeng; Meng, Fanming; Fan, Zhenghua; Li, Huijie

    2016-10-01

    Monodisperse 3D lotus-like CeO2 microstructures have been successfully synthesized via controlling the morphology of CeCO3OH precursors under hydrothermal condition as well as subsequent calcination. The reaction time was systematically investigated. XRD, FT-IR, SEM, TEM, XPS, Raman scattering and Photoluminescence (PL) spectra were employed to characterize the samples. The lotus-like CeO2 hierarchical structures with an average of 4-6 μm are composed of many nanoplates of 100-200 nm in thickness as the petals stacking together to form open flowers and have a fluorite cubic structure. Based on the time-dependent morphology evolution evidences, a nucleation-dissolution-recrystallization mechanism has been proposed to explain the transformation from rod-like structures to lotus-like CeO2 hierarchical structures with the increase of reaction time. It is found that there are Ce3+ ions and oxygen vacancies in surface of samples. The magnetic and photoluminescence measurements indicated that all CeO2 samples exhibit excellent ferromagnetism and optical properties at room temperature, and while increasing the reaction time, the ferromagnetism and optical properties increase more, which can be reasonably explained for the influences of the different morphology of the particles and the concentration of oxygen vacancies and Ce3+ ions. [Figure not available: see fulltext.

  8. Evaluation of the morphological alteration of the root surface radiated with a diode laser

    International Nuclear Information System (INIS)

    Gulin, Mauricio

    2003-01-01

    The diode laser has been studied for periodontal therapy, as much for removal of calculus as for microbial reduction of periodontal pockets, as well as the visible analgesic effects and biomodulation capacity. For this reason the purpose of this study was to evaluate the morphological alteration of the root surface after radiation with the diode laser, 808 nm through analysis by scanning electron microscopy (SEM). Besides this, to verify the temperature variations caused during the radiation, a thermometer put into the dentinal wall of the root canal was used. In all, 18 teeth were used, 15 of which for the SEM study, and the other 3 were used to temperature variation analysis. The 25 samples were scraped on the root surface and planed with manual instruments. The other 5 were not subjected to any type of treatment. This, 6 groups of 5 samples each were formed. Control Group C whose samples had not received any treatment; Control Group C 1 was only scraped and polished conventionally with Hu-Friedy Gracey curettes 5 and 6; the other samples groups L1, L2, L3, L4 were radiated by diode laser using parameters of power 1,0 W; 1,2 W; 1,4 W; and 1,6 W respectively, 2 times for 10 seconds with 20 seconds intervals between each radiation in continuous mode. The results with relation to the increase of temperature in the interior of the root canal demonstrated that there was an increase of more than 5 degree Celsius. The results of the scanning electron microscope analysis of Control Group C demonstrated great irregularity and ridges on the root surface, with the presence of a dentine layer. Control Group C1 presented a similar aspect to Group L 1's, smoother and more homogeneous surface. Groups L2, L3, and L4 presented scratches alternating with smoother areas showing that fiber contacted the surface of the sample. The results reconfirmed the necessity of further studies using diode laser, with a beam of light emitted in an interrupted mode to improve the control of the

  9. Damage morphology of Kr ion tracks in apatite: Dependence on dE/dX

    CERN Document Server

    Villa, F; Rebetez, M; Dubois, C; Chambaudet, A; Chevarier, A; Martin, P; Brossard, F; Blondiaux, G; Sauvage, T; Toulemonde, M

    1999-01-01

    With the aim of characterizing damage along nuclear tracks in apatite, Durango fluoroapatite monocrystals were irradiated under a high fluence sup 8 sup 6 Kr ion beam at the G.A.N.I.L. (Grand Accelerateur National d'Ions Lourds, Caen, France). The resulting irradiation damage was studied by associating CRBS spectrometry and chemical etching. By applying Poisson's law to the backscattering results, the nuclear track average effective radius R sub e was calculated for different steps along the ion path. On the other hand, the chemical etching experiments allowed us to deduce three different damaging morphologies in correspondence to the R sub e values. For the first time in apatite, it has been shown that a defect fragmentation produced along the ion paths may be detected by chemical etching. These results were also applied to fission tracks in order to quantify the damage rate and to describe the damage morphology evolution along fission fragment paths.

  10. 2.5D constructs for characterizing phase separated polymer blend surface morphology in tissue engineering scaffolds.

    Science.gov (United States)

    Marszalek, Jolanta E; Simon, Carl G; Thodeti, Charles; Adapala, Ravi Kumar; Murthy, Ananth; Karim, Alamgir

    2013-05-01

    Previously, we used 2D films to identify an annealed PCL-PDLLA phase-separated blend morphology which provided nanoscale surface texture and patterning that stimulated osteoblast differentiation. In order to translate these 2D surface nanopatterning effects to the walls of 3D salt-leached scaffolds, the blend phase morphology of scaffold walls must be characterized. For salt-leached scaffolds, NaCl is used as a porogen, which may affect phase separation in PCL-PDLLA blends. However, it is not possible to characterize the surface blend morphology of 3D scaffold walls using standard approaches such as AFM or optical microscopy, since scaffolds are too rough for AFM and do not transmit light for optical microscopy. We introduce a 2.5D approach that mimics the processing conditions of 3D salt-leached scaffolds, but has a geometry amenable to surface characterization by AFM and optical microscopy. For the 2.5D approach, PCL-PDLLA blend films were covered with NaCl crystals prior to annealing. The presence of NaCl significantly influenced blend morphology in PCL-PDLLA 2.5D constructs causing increased surface roughness, higher percent PCL area on the surface and a smaller PCL domain size. During cell culture on 2.5D constructs, osteoblast (MC3T3-E1) and dermal endothelial cell (MDEC) adhesion were enhanced on PCL-PDLLA blends that were annealed with NaCl while chondrogenic cell (ATDC5) adhesion was diminished. This work introduces a 2.5D approach that mimicked 3D salt-leached scaffold processing, but enabled characterization of scaffold surface properties by AFM and light microscopy, to demonstrate that the presence of NaCl during annealing strongly influenced polymer blend surface morphology and cell adhesion. Copyright © 2012 Wiley Periodicals, Inc.

  11. Surface composition of silver nanocubes and their influence on morphological stabilization and catalytic performance in ethylene epoxidation

    KAUST Repository

    Sangaru, Shiv

    2015-12-04

    Silver nanocubes with exposed (100) facets are reported to have improved selectivity with respect to their spherical counterparts for ethylene epoxidation. In the present study, we observe that the surface composition of the silver nanocubes have also a critical impact on activity. Detailed investigation of the surface composition of silver nanocubes has been carried out using HRTEM, SEM, EDS, EELS and EFTEM. Surfaces of silver nanocubes are “passivated” by chloride and its removal is essential to achieve any catalytic activity. However, the surface chloride is apparently essential for stabilizing the cubic morphology of the particles. Attempts were made to understand the competing effects of the surface species for retaining the morphology of the nanocubes and on their catalytic activity.

  12. Surface morphology of PMMA/boehmite hybrid nanostructures prepared via facile one-pot process

    Science.gov (United States)

    Ghamari, Misagh; Farzi, Gholamali

    2017-08-01

    In this study, we developed the novel aqueous-based PMMA/AlOOH hybrid by a one-pot process starting from their relevant precursors in a controlled manner. Starting chemical reactions directly from precursors and the sequence of adding reactants provide the possibility towards enhancing the homogeneity of the final product. Inorganic and organic segments were made compatible by means of oleic acid as a coupling agent. Boehmite to PMMA weight ratio as the main parameter was varied from 0 to 18% and the morphology, particle size, size distribution, and topography map of hybrids was shown to be composition dependent. Final PMMA/Bo nanohybrids were characterized using FTIR to confirm the chemical interactions between inorganic and organic segments. TEM analysis showed that nanohybrid particles with irregular shapes containing inorganic particles dispersed in the organic matrix are formed with an average diameter which depends on boehmite content. The presence of phase transformation of Bo makes PMMA/Bo hybrids significantly thermally stable. According to AFM topography map analysis and relevant Gaussian fit function, the roughness of nanocomposite, the size of hybrid nanoparticles and deviation from the mean value (size) were increased as Bo increases from 0 to 18.

  13. Hole-Transfer Dependence on Blend Morphology and Energy Level Alignment in Polymer: ITIC Photovoltaic Materials.

    Science.gov (United States)

    Eastham, Nicholas D; Logsdon, Jenna L; Manley, Eric F; Aldrich, Thomas J; Leonardi, Matthew J; Wang, Gang; Powers-Riggs, Natalia E; Young, Ryan M; Chen, Lin X; Wasielewski, Michael R; Melkonyan, Ferdinand S; Chang, Robert P H; Marks, Tobin J

    2018-01-01

    Bulk-heterojunction organic photovoltaic materials containing nonfullerene acceptors (NFAs) have seen remarkable advances in the past year, finally surpassing fullerenes in performance. Indeed, acceptors based on indacenodithiophene (IDT) have become synonymous with high power conversion efficiencies (PCEs). Nevertheless, NFAs have yet to achieve fill factors (FFs) comparable to those of the highest-performing fullerene-based materials. To address this seeming anomaly, this study examines a high efficiency IDT-based acceptor, ITIC, paired with three donor polymers known to achieve high FFs with fullerenes, PTPD3T, PBTI3T, and PBTSA3T. Excellent PCEs up to 8.43% are achieved from PTPD3T:ITIC blends, reflecting good charge transport, optimal morphology, and efficient ITIC to PTPD3T hole-transfer, as observed by femtosecond transient absorption spectroscopy. Hole-transfer is observed from ITIC to PBTI3T and PBTSA3T, but less efficiently, reflecting measurably inferior morphology and nonoptimal energy level alignment, resulting in PCEs of 5.34% and 4.65%, respectively. This work demonstrates the importance of proper morphology and kinetics of ITIC → donor polymer hole-transfer in boosting the performance of polymer:ITIC photovoltaic bulk heterojunction blends. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  14. Endoplasmic Reticulum Lipid Flux Influences Enterocyte Nuclear Morphology and Lipid-dependent Transcriptional Responses.

    Science.gov (United States)

    Zeituni, Erin M; Wilson, Meredith H; Zheng, Xiaobin; Iglesias, Pablo A; Sepanski, Michael A; Siddiqi, Mahmud A; Anderson, Jennifer L; Zheng, Yixian; Farber, Steven A

    2016-11-04

    Responding to a high-fat meal requires an interplay between multiple digestive tissues, sympathetic response pathways, and the gut microbiome. The epithelial enterocytes of the intestine are responsible for absorbing dietary nutrients and preparing them for circulation to distal tissues, which requires significant changes in cellular activity, including both morphological and transcriptional responses. Following a high-fat meal, we observe morphological changes in the enterocytes of larval zebrafish, including elongation of mitochondria, formation and expansion of lipid droplets, and the rapid and transient ruffling of the nuclear periphery. Dietary and pharmacological manipulation of zebrafish larvae demonstrated that these subcellular changes are specific to triglyceride absorption. The transcriptional changes that occur simultaneously with these morphological changes were determined using RNA sequencing, revealing a cohort of up-regulated genes associated with lipid droplet formation and lipid transport via lipoprotein particles. Using a microsomal triglyceride transfer protein (MTP) inhibitor to block β-lipoprotein particle formation, we demonstrate that the transcriptional response to a high-fat meal is associated with the transfer of ER triglyceride to nascent β-lipoproteins, possibly through the activation of Creb3l3/cyclic AMP-responsive element-binding protein. These data suggest that a transient increase in ER lipids is the likely mediator of the initial physiological response of intestinal enterocytes to dietary lipid. © 2016 by The American Society for Biochemistry and Molecular Biology, Inc.

  15. Endoplasmic Reticulum Lipid Flux Influences Enterocyte Nuclear Morphology and Lipid-dependent Transcriptional Responses*

    Science.gov (United States)

    Zeituni, Erin M.; Wilson, Meredith H.; Zheng, Xiaobin; Iglesias, Pablo A.; Sepanski, Michael A.; Siddiqi, Mahmud A.; Anderson, Jennifer L.; Zheng, Yixian; Farber, Steven A.

    2016-01-01

    Responding to a high-fat meal requires an interplay between multiple digestive tissues, sympathetic response pathways, and the gut microbiome. The epithelial enterocytes of the intestine are responsible for absorbing dietary nutrients and preparing them for circulation to distal tissues, which requires significant changes in cellular activity, including both morphological and transcriptional responses. Following a high-fat meal, we observe morphological changes in the enterocytes of larval zebrafish, including elongation of mitochondria, formation and expansion of lipid droplets, and the rapid and transient ruffling of the nuclear periphery. Dietary and pharmacological manipulation of zebrafish larvae demonstrated that these subcellular changes are specific to triglyceride absorption. The transcriptional changes that occur simultaneously with these morphological changes were determined using RNA sequencing, revealing a cohort of up-regulated genes associated with lipid droplet formation and lipid transport via lipoprotein particles. Using a microsomal triglyceride transfer protein (MTP) inhibitor to block β-lipoprotein particle formation, we demonstrate that the transcriptional response to a high-fat meal is associated with the transfer of ER triglyceride to nascent β-lipoproteins, possibly through the activation of Creb3l3/cyclic AMP-responsive element-binding protein. These data suggest that a transient increase in ER lipids is the likely mediator of the initial physiological response of intestinal enterocytes to dietary lipid. PMID:27655916

  16. Substrate dependent morphologies of self-assembled nanocrystalline manganite films: An atomic force microscopy study

    International Nuclear Information System (INIS)

    Kale, S.N.; Mona, J.; Ganesan, V.; Choudhary, R.J.; Phase, D.M.

    2009-06-01

    Thin films of La 0 .7Sr 0 .3MnO 3 (LSMO) have been deposited on different substrates: Si (001), Al 2 O 3 (AlO) (0001) and LaAlO 3 (LAO) (001), using a pulsed laser deposition system. 100 nm films have been deposited at substrate temperature of 700 deg C and oxygen partial pressure of 400 mTorr. X-Ray diffraction analysis shows a polycrystalline growth of both layers on Si and Al 2 O 3 substrates, while a c-axis oriented growth on LAO substrate. Atomic force microscopy images exhibit interesting island-like morphology of grain size ∼ 250 nm on Si substrate. Similar morphology with much smaller (∼ 150 nm), closely packed islands are seen to grow on AlO substrate. Films on LAO show comparatively a smooth morphology with the grains size less than 100 nm, decorated by characteristic depressions at the grain boundaries. The formation of self-assembled nanostructures can be understood on the basis of film-substrate lattice misfit, strains in the systems and eventual growth of the films to attain energy minimization (author)

  17. Morphology-dependent water budgets and nutrient fluxes in arctic thaw ponds

    Science.gov (United States)

    Koch, Joshua C.; Gurney, Kirsty; Wipfli, Mark S.

    2014-01-01

    Thaw ponds on the Arctic Coastal Plain of Alaska are productive ecosystems, providing habitat and food resources for many fish and bird species. Permafrost in this region creates unique pond morphologies: deep troughs, shallow low-centred polygons (LCPs) and larger coalescent ponds. By monitoring seasonal trends in pond volume and chemistry, we evaluated whether pond morphology and size affect water temperature and desiccation, and nitrogen (N) and phosphorus (P) fluxes. Evaporation was the largest early-summer water flux in all pond types. LCPs dried quickly and displayed high early-summer nutrient concentrations and losses. Troughs consistently received solute-rich subsurface inflows, which accounted for 12 to 42 per cent of their volume and may explain higher P in the troughs. N to P ratios increased and ammonium concentrations decreased with pond volume, suggesting that P and inorganic N availability may limit ecosystem productivity in older, larger ponds. Arctic summer temperatures will likely increase in the future, which may accelerate mid-summer desiccation. Given their morphology, troughs may remain wet, become warmer and derive greater nutrient loads from their thawing banks. Overall, seasonal- to decadal-scale warming may increase ecosystem productivity in troughs relative to other Arctic Coastal Plain ponds. 

  18. Mesomorphism of Newly Synthesized Mesogens and Surface Morphology of Chalcogenide Glass Thin Films

    Science.gov (United States)

    Sharpnack, Lewis Lee

    -ray reflectivity profiles to facilitate a comparison with other alignment layers that generate liquid crystal alignment primarily because of their anisotropic surface morphology. Our results reveal that As2S3 films develop anisotropic features under irradiation with polarized blue light that are consistent with the changes that occur in other alignment layers when they are "treated" either with mechanical buffing of polymer films or exposure to linearly polarized UV light. These studies also reveal the development of an extensive oxide layer and the ablation of the film under ambient conditions owing to the absorption of oxygen and moisture. This represents a significant barrier to their commercial applications.

  19. The maintenance of sperm variability: context-dependent selection on sperm morphology in a broadcast spawning invertebrate.

    Science.gov (United States)

    Johnson, Darren W; Monro, Keyne; Marshall, Dustin J

    2013-05-01

    Why are sperm so variable despite having a singular, critical function and an intimate relationship with fitness? A key to understanding the evolution of sperm morphology is identifying which traits enable sperm to be successful fertilizers. Several sperm traits (e.g., tail length, overall size) are implicated in sperm performance, but the benefits of these traits are likely to be highly context dependent. Here, we examined phenotypic selection on sperm morphology of a broadcast spawning tube worm (Galeolaria gemineoa). We conducted laboratory experiments to measure the relationship between average sperm morphology and relative fertilization success across a range of sperm environments that were designed to approximate the range of sperm concentrations and ages encountered by eggs in nature. We found that the strength and form of multivariate selection varied substantially across our environmental gradients. Sperm with long tails and small heads were favored in high-concentration environments, whereas sperm with long heads were favored at low concentrations and old ages. We suggest variation in the local fertilization environment and resulting differences in selection can preserve variability in sperm morphology both within and among males. © 2012 The Author(s). Evolution © 2012 The Society for the Study of Evolution.

  20. Energy dependent neutron sputtering and surface damage cross sections

    International Nuclear Information System (INIS)

    Odette, G.R.; Doiron, D.R.; Kennerley, R.J.

    1976-01-01

    The results clearly indicate that damage function analysis might be usefully applied to define both the neutron and primary recoil energy dependence of sputtering yields. Even with relatively large data errors, it appears that it is possible to both detect the existence and indicate the form of the deviation of sputtering yield from linear damage energy dependence (if such deviation exists). This information would be very useful in developing improved models of the sputtering phenomena

  1. Layer-dependent surface potential of phosphorene and anisotropic/layer-dependent charge transfer in phosphorene-gold hybrid systems.

    Science.gov (United States)

    Xu, Renjing; Yang, Jiong; Zhu, Yi; Yan, Han; Pei, Jiajie; Myint, Ye Win; Zhang, Shuang; Lu, Yuerui

    2016-01-07

    The surface potential and the efficiency of interfacial charge transfer are extremely important for designing future semiconductor devices based on the emerging two-dimensional (2D) phosphorene. Here, we directly measured the strong layer-dependent surface potential of mono- and few-layered phosphorene on gold, which is consistent with the reported theoretical prediction. At the same time, we used an optical way photoluminescence (PL) spectroscopy to probe charge transfer in the phosphorene-gold hybrid system. We firstly observed highly anisotropic and layer-dependent PL quenching in the phosphorene-gold hybrid system, which is attributed to the highly anisotropic/layer-dependent interfacial charge transfer.

  2. Data on the surface morphology of additively manufactured Ti-6Al-4V implants during processing by plasma electrolytic oxidation

    Directory of Open Access Journals (Sweden)

    Ingmar A.J. van Hengel

    2017-08-01

    Full Text Available Additively manufactured Ti-6Al-4V implants were biofunctionalized using plasma electrolytic oxidation. At various time points during this process scanning electron microscopy imaging was performed to analyze the surface morphology (van Hengel et al., 2017 [1]. This data shows the changes in surface morphology during plasma electrolytic oxidation. Data presented in this article are related to the research article “Selective laser melting porous metallic implants with immobilized silver nanoparticles kill and prevent biofilm formation by methicillin-resistant Staphylococcus aureus” (van Hengel et al., 2017 [1].

  3. Influence of thermal annealing on microstructural, morphological, optical properties and surface electronic structure of copper oxide thin films

    Energy Technology Data Exchange (ETDEWEB)

    Akgul, Funda Aksoy, E-mail: fundaaksoy01@gmail.com [Department of Physics, Nigde University, 51240 Nigde (Turkey); Center for Solar Energy Research and Applications, Middle East Technical University, 06800 Ankara (Turkey); Akgul, Guvenc, E-mail: guvencakgul@gmail.com [Bor Vocational School, Nigde University, 51700 Nigde (Turkey); Center for Solar Energy Research and Applications, Middle East Technical University, 06800 Ankara (Turkey); Yildirim, Nurcan [Department of Physics Engineering, Ankara University, 06100 Ankara (Turkey); Department of Metallurgical and Materials Engineering, Middle East Technical University, 06800 Ankara (Turkey); Unalan, Husnu Emrah [Department of Metallurgical and Materials Engineering, Middle East Technical University, 06800 Ankara (Turkey); Center for Solar Energy Research and Applications, Middle East Technical University, 06800 Ankara (Turkey); Turan, Rasit [Department of Physics, Middle East Technical University, 06800 Ankara (Turkey); Center for Solar Energy Research and Applications, Middle East Technical University, 06800 Ankara (Turkey)

    2014-10-15

    In this study, effect of the post-deposition thermal annealing on copper oxide thin films has been systemically investigated. The copper oxide thin films were chemically deposited on glass substrates by spin-coating. Samples were annealed in air at atmospheric pressure and at different temperatures ranging from 200 to 600°C. The microstructural, morphological, optical properties and surface electronic structure of the thin films have been studied by diagnostic techniques such as X-ray diffraction (XRD), Raman spectroscopy, ultraviolet–visible (UV–VIS) absorption spectroscopy, field emission scanning electron microscopy (FESEM), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS). The thickness of the films was about 520 nm. Crystallinity and grain size was found to improve with annealing temperature. The optical bandgap of the samples was found to be in between 1.93 and 2.08 eV. Cupric oxide (CuO), cuprous oxide (Cu{sub 2}O) and copper hydroxide (Cu(OH){sub 2}) phases were observed on the surface of as-deposited and 600 °C annealed thin films and relative concentrations of these three phases were found to depend on annealing temperature. A complete characterization reported herein allowed us to better understand the surface properties of copper oxide thin films which could then be used as active layers in optoelectronic devices such as solar cells and photodetectors. - Highlights: • Effect of post-deposition annealing on copper oxide thin films was investigated. • Structural, optical, and electronic properties of the thin films were determined. • Oxidation states of copper oxide thin films were confirmed by XPS analysis. • Mixed phases of CuO and Cu{sub 2}O were found to coexist in copper oxide thin films.

  4. Optical Properties and Surface Morphology of Nano-composite PMMA: TiO2 Thin Films

    International Nuclear Information System (INIS)

    Lyly Nyl Ismail; Ahmad Fairoz Aziz; Habibah Zulkefle

    2011-01-01

    There are two nano-composite PMMA: TiO 2 solutions were prepared in this research. First solution is nano-composite PMMA commercially available TiO 2 nanopowder and the second solution is nano-composite PMMA with self-prepared TiO 2 powder. The self-prepared TiO 2 powder is obtained by preparing the TiO 2 sol-gel. Solvo thermal method were used to dry the TiO 2 sol-gel and obtained TiO 2 crystal. Ball millers were used to grind the TiO 2 crystal in order to obtained nano sized powder. Triton-X was used as surfactant to stabilizer the composite between PMMA: TiO 2 . Besides comparing the nano-composite solution, we also studied the effect of the thin films thickness on the optical properties and surface morphology of the thin films. The thin films were deposited by sol-gel spin coating method on glass substrates. The optical properties and surface characterization were measured with UV-VIS spectrometer equipment and atomic force microscopy (AFM). The result showed that nano-composite PMMA with self prepared TiO 2 give high optical transparency than nano-composite PMMA with commercially available TiO 2 nano powder. The results also indicate as the thickness is increased the optical transparency are decreased. Both AFM images showed that the agglomerations of TiO 2 particles are occurred on the thin films and the surface roughness is increased when the thickness is increased. High agglomeration particles exist in the AFM images for nano-composite PMMA: TiO 2 with TiO 2 nano powder compare to the other nano-composite solution. (author)

  5. Surface morphology of silicone soft relining material after mechanical and chemical cleaning.

    Science.gov (United States)

    Ueda, Takayuki; Kubo, Keitaro; Saito, Takeshi; Obata, Tomokuni; Wada, Takeshi; Yanagisawa, Koichiro; Sakurai, Kaoru

    2018-04-07

    The objective was to investigate the influence of chemical and mechanical cleaning on the surface morphology of a silicone soft relining material. Three plate-shaped specimens were prepared for each group (Control, Hard and Soft) by laminating a 1.5-mm-thick silicone soft relining material. The Control group specimens were stored in water, and the Hard and Soft group specimens were cleaned with hard and soft bristle denture brushes, respectively. Abrasion testing with a toothbrush and immersion testing with an enzyme-containing peroxide denture cleanser were performed, simulating a period of approximately 4 months. The arithmetic mean roughness (Sa) and maximum height of the cross-section (Sz) were measured before and after abrasion and immersion testing. Sa was 4.9±0.9, 22.1±4.2 and 44.2±4.0μm in the Control, Soft and Hard groups, respectively. Sz was 257.5±31.7, 392.0±23.8 and 452.2±41.9μm in the Control, Soft and Hard groups, respectively. After abrasion testing, Sa and Sz differed significantly between the Soft and Control groups and between the Hard and Control groups. Sa was 2.2±1.2μm before and after immersion, and Sz was 142.1±81.4μm before and after immersion. No significant difference was noted in either Sa or Sz in the Control specimens before or after immersion. Surfaces cleaned using a soft bristle brush were less likely to roughen than those cleaned with a hard bristle brush under the conditions of this study. Additionally, chemical cleaning using the enzyme+neutral peroxide denture cleanser did not roughen the surface of the silicone soft relining material. Copyright © 2018 Japan Prosthodontic Society. Published by Elsevier Ltd. All rights reserved.

  6. Pronounced Size Dependence in Structure and Morphology of Gas-Phase Produced, Partially Oxidized Cobalt Nanoparticles under Catalytic Reaction Conditions.

    Science.gov (United States)

    Bartling, Stephan; Yin, Chunrong; Barke, Ingo; Oldenburg, Kevin; Hartmann, Hannes; von Oeynhausen, Viola; Pohl, Marga-Martina; Houben, Kelly; Tyo, Eric C; Seifert, Sönke; Lievens, Peter; Meiwes-Broer, Karl-Heinz; Vajda, Stefan

    2015-06-23

    It is generally accepted that optimal particle sizes are key for efficient nanocatalysis. Much less attention is paid to the role of morphology and atomic arrangement during catalytic reactions. Here, we unravel the structural, stoichiometric, and morphological evolution of gas-phase produced and partially oxidized cobalt nanoparticles in a broad size range. Particles with diameters between 1.4 and 22 nm generated in cluster sources are size selected and deposited on amorphous alumina (Al2O3) and ultrananocrystalline diamond (UNCD) films. A combination of different techniques is employed to monitor particle properties at the stages of production, exposure to ambient conditions, and catalytic reaction, in this case, the oxidative dehydrogenation of cyclohexane at elevated temperatures. A pronounced size dependence is found, naturally classifying the particles into three size regimes. While small and intermediate clusters essentially retain their compact morphology, large particles transform into hollow spheres due to the nanoscale Kirkendall effect. Depending on the substrate, an isotropic (Al2O3) or anisotropic (UNCD) Kirkendall effect is observed. The latter results in dramatic lateral size changes. Our results shed light on the interplay between chemical reactions and the catalyst's structure and provide an approach to tailor the cobalt oxide phase composition required for specific catalytic schemes.

  7. Pronounced Size Dependence in Structure and Morphology of Gas-Phase Produced, Partially Oxidized Cobalt Nanoparticles under Catalytic Reaction Conditions

    Energy Technology Data Exchange (ETDEWEB)

    Bartling, Stephan; Yin, Chunrong; Barke, Ingo; Oldenburg, Kevin; Hartmann, Hannes; von Oeynhausen, Viola; Pohl, Marga-Martina; Houben, Kelly; Tyo, Eric C.; Seifert, Sönke; Lievens, Peter; Meiwes-Broer, Karl-Heinz; Vajda, Stefan

    2015-06-23

    It is generally accepted that optimal particle sizes are key for efficient nanocatalysis. Much less attention is paid to the role of morphology and atomic arrangement during catalytic reactions. Here we unravel the structural, stoichiometric, and morphological evolution of gas-phase produced cobalt nanoparticles in a broad size range. Particles with diameters between 1.4 nm and 22nm generated in cluster sources are size selected and deposited on amorphous alumina (Al2O3) and ultrananocrystalline diamond (UNCD) films. A combination of different techniques is employed to monitor particle properties at the stages of production, exposure to ambient conditions, and catalytic reaction, in this case the oxidative dehydrogenation of cyclohexane at elevated temperatures. A pronounced size dependence is found, naturally classifying the particles into three size regimes. While small and intermediate clusters essentially retain their compact morphology, large particles transform into hollow spheres due to the nanoscale Kirkendall effect. Depending on the substrate an isotropic (Al2O3) or anisotropic (UNCD) Kirkendall effect is observed. The latter results in dramatic lateral size changes. Our results shed light on the interplay between chemical reactions and the catalyst's structure and provide an approach to tailor the cobalt oxide phase composition required for specific catalytic schemes.

  8. Dependence of metal-enhanced fluorescence on surface roughness

    Science.gov (United States)

    François, Alexandre; Sciacca, Beniamino; Zuber, Agnieszka; Klantsataya, Elizaveta; Monro, Tanya M.

    2014-03-01

    Metal Enhanced Fluorescence (MEF) takes advantage of the coupling between surface plasmons, in either a metallic thin film or metallic nanoparticles, and fluorophores located in proximity of the metal, yielding an increase of the fluorophore emission. While MEF has been widely studied on metallic nanoparticles with the emphasis on creating brighter fluorescent labels, planar surfaces have not benefitted from the same attention. Here we investigate the influence of the surface roughness of a thin metallic film on the fluorescence enhancement. 50nm thick silver films were deposited on glass slides using either thermal evaporation with different evaporation currents or an electroless plating method based on the Tollens reaction to vary the surface roughness. Multiple layers of positively and negatively charged polyelectrolytes were deposited on top of the metallic coating to map out the enhancement factor as function of the gap between the metallic coating and fluorophore molecules covalently bound to the last polyelectrolyte layer. We show that fluorescence is enhanced by the presence of the metallic film, and in particular that the enhancement increases by a factor 3 to 40 for roughness ranging from 3 nm to 8 nm. Although these enhancement factors are modest compared to the enhancement produced by complex metallic nanoparticles or nano-patterned metallic thin films, the thin films used here are capable of supporting a plasmonic wave and offer the possibility of combining different techniques, such as surface plasmon resonance (with its higher refractive index sensitivity compared to localized plasmons) and MEF within a single device.

  9. Three-dimensional morphological analysis of the human sacroiliac joint: influences on the degenerative changes of the auricular surfaces.

    Science.gov (United States)

    Nishi, Keita; Tsurumoto, Toshiyuki; Okamoto, Keishi; Ogami-Takamura, Keiko; Hasegawa, Takashi; Moriuchi, Takefumi; Sakamoto, Junya; Oyamada, Joichi; Higashi, Toshio; Manabe, Yoshitaka; Saiki, Kazunobu

    2018-02-01

    The sacroiliac joint (SIJ) is responsible for weight transmission between the spine and lower extremity. However, details of the structure and function of the SIJ remain unclear. In a previous study, we devised a method of quantitatively evaluating the level of degeneration of the SIJ using an age estimation procedure for the auricular surface of the ilium. Our results in that study suggested that the degree of degeneration of the joint surface may be associated with the morphology of the auricular surface of the ilium. In that study, however, the morphology of the auricular surface of the ilium was simplified for analysis, meaning that more detailed investigations were required in future. In the present study, we focused on individual differences in the shape of SIJ and carried out three-dimensional quantitative evaluation of the morphology of the auricular surface of the ilium to ascertain its association with joint degeneration. We produced three-dimensional images of the right auricular surfaces of the ilium of 100 modern Japanese men (age 19-83), and obtained the three-dimensional rectangular coordinates of 11 defined measurement points. We then calculated 16 parameters indicating the morphological characteristics of the auricular surfaces of the ilium from the three-dimensional rectangular coordinates of these measurement points, and used these to perform principal component analysis to investigate trends in the morphology of the auricular surface of the ilium. We found that the morphology of the auricular surface of the ilium could be characterized in terms of (i) size, (ii) concavity of the posterior border and (iii) amount of undulation. An investigation of the correlation between these parameters and age suggested that the amount of undulation of the auricular surface of the ilium tends to diminish with advancing age. In an investigation of the association between morphology of the auricular surface of the ilium and degeneration of the articular surface

  10. Porosity-dependent fractal nature of the porous silicon surface

    Energy Technology Data Exchange (ETDEWEB)

    Rahmani, N.; Dariani, R. S., E-mail: dariani@alzahra.ac.ir [Department of Physics, Alzahra University, Tehran, 1993893973 (Iran, Islamic Republic of)

    2015-07-15

    Porous silicon films with porosity ranging from 42% to 77% were fabricated by electrochemical anodization under different current density. We used atomic force microscopy and dynamic scaling theory for deriving the surface roughness profile and processing the topography of the porous silicon layers, respectively. We first compared the topography of bare silicon surface with porous silicon and then studied the effect of the porosity of porous silicon films on their scaling behavior by using their self-affinity nature. Our work demonstrated that silicon compared to the porous silicon films has the highest Hurst parameter, indicating that the formation of porous layer due to the anodization etching of silicon surface leads to an increase of its roughness. Fractal analysis revealed that the evolution of the nanocrystallites’ fractal dimension along with porosity. Also, we found that both interface width and Hurst parameter are affected by the increase of porosity.

  11. Surface morphology modelling for the resistivity analysis of low temperature sputtered indium tin oxide thin films on polymer substrates

    International Nuclear Information System (INIS)

    Yin Xuesong; Tang Wu; Weng Xiaolong; Deng Longjiang

    2009-01-01

    Amorphous or weakly crystalline indium tin oxide (ITO) thin film samples have been prepared on polymethylmethacrylate and polyethylene terephthalate substrates by RF-magnetron sputtering at a low substrate temperature. The surface morphological and electrical properties of the ITO layers were measured by atomic force microscopy (AFM) and a standard four-point probe measurement. The effect of surface morphology on the resistivity of ITO thin films was studied, which presented some different variations from crystalline films. Then, a simplified film system model, including the substrate, continuous ITO layer and ITO surface grain, was proposed to deal with these correlations. Based on this thin film model and the AFM images, a quadratic potential was introduced to simulate the characteristics of the ITO surface morphology, and the classical Kronig-Penney model, the semiconductor electrical theory and the modified Neugebauer-Webb model were used to expound the detailed experimental results. The modelling equation was highly in accord with the experimental variations of the resistivity on the characteristics of the surface morphology.

  12. Effects of polymer surface energy on morphology and properties of silver nanowire fabricated via nanoimprint and E-beam evaporation

    Science.gov (United States)

    Zhao, Zhi-Jun; Hwang, Soon Hyoung; Jeon, Sohee; Jung, Joo-Yun; Lee, Jihye; Choi, Dae-Geun; Choi, Jun-Hyuk; Park, Sang-Hu; Jeong, Jun-Ho

    2017-10-01

    In this paper, we demonstrate that use of different nanoimprint resins as a polymer pattern has a significant effect on the morphology of silver (Ag) nanowires deposited via an E-beam evaporator. RM-311 and Ormo-stamp resins are chosen as a polymer pattern to form a line with dimensions of width (100 nm) × space (100 nm) × height (120 nm) by using nanoimprint lithography (NIL). Their contact angles are then measured to evaluate their surface energies. In order to compare the properties of the Ag nanowires deposited on the various polymer patterns with different surface energies, hydrophobic surface treatment of the polymer pattern surface is implemented using self-assembled monolayers. In addition, gold and aluminum nanowires are fabricated for comparison with the Ag nanowires, with the differences in the nanowire morphologies being determined by the different atomic properties. The monocrystalline and polycrystalline structures of the various Ag nanowire formations are observed using transmission electron microscopy. In addition, the melting temperatures and optical properties of four kinds of Ag nanowire morphologies deposited on various polymer patterns are evaluated using a hot plate and an ultraviolet-visible (UV-vis) spectrometer, respectively. The results indicate that the morphology of the Ag nanowire determines the melting temperature and the transmission. We believe that these findings will greatly aid the development of NIL, along with physical evaporation and chemical deposition techniques, and will be widely employed in optics, biology, and surface wettability applications.

  13. Changes in surface morphology of enamel after Er:YAG laser irradiation

    Science.gov (United States)

    Rechmann, Peter; Goldin, Dan S.; Hennig, Thomas

    1998-04-01

    Aim of the study was to investigate the surface and subsurface structure of enamel after irradiation with an Er:YAG laser (wavelength 2.94 micrometer, pulse duration 250 - 500 microseconds, free running, beam profile close to tophead, focus diameter 600 micrometer, focus distance 13 mm, different power settings, air-water spray 2 ml/min; KAVO Key Laser 1242, Kavo Biberach, Germany). The surface of more than 40 freshly extracted wisdom teeth were irradiated using a standardized application protocol (pulse repetition rate 4 and 6 Hz, moving speed of the irradiation table 2 mm/sec and 3 mm/sec, respectively). On each surface between 3 and 5 tracks were irradiated at different laser energies (60 - 500 mJ/pulse) while each track was irradiated between one and ten times respectively. For the scanning electron microscope investigation teeth were dried in alcohol and sputtered with gold. For light microscopic examinations following laser impact, samples were fixed in formaldehyde, dried in alcohol and embedded in acrylic resin. Investigations revealed that at subsurface level cracks can not be observed even at application of highest energies. Borders of the irradiated tracks seem to be sharp while melted areas of different sizes are observed on the bottom of the tracks depending on applied energy. Small microcracks can be seen on the surface of these melted areas.

  14. In-Vitro Comparative Study of In-office and Home Bleaching Agents on Surface Micro-morphology of Enamel.

    Science.gov (United States)

    Fatima, Nazish

    2016-01-01

    To evaluate the effect of home-use bleaching agent containing 16% Carbamide Peroxide (CP) and in-office bleaching agent with 38% Hydrogen Peroxide (HP) on surface micro-morphology of enamel. An experimental study. The discs were prepared at Material Engineering Department of NED University of Engineering and Technology, Karachi, and surface morphology was analyzed at Centralized Science Laboratory of Karachi University, Pakistan. Duration of study was one year from January to December 2012. Forty five sound human third molar crowns, extracted for periodontal reason, were included in the study. Longitudinal sections were made using diamond disks (0.2 mm) under water lubrication to obtain enamel slabs measuring (3 mm x 3 mm). The slabs were embedded in polystyrene resin by using 2.0 cm diameter PVC molds, leaving the outer enamel surface uncovered by the resin. Ninety dental enamel slabs were prepared. The slabs were then randomly divided into 3 groups. Each group contained thirty specimens (n=30). Group 1 was kept in artificial saliva at 37°C in incubator (Memart, Germany) during whole experiment. Group 2 was treated with power whitening gel (White Smile 2011, Germany). Group 3 was treated with tooth whitening pen (White Smile 2011, Germany). The most central region or the region that was most representative of the entire surface area was used. The SEM (Jeol-Japan-JSM6380A, JAPAN) micrographs were examined to determine the type of surface presented. The enamel changes were classified as no or mild alteration, moderate alteration and severe altered surface. Regarding micro-morphology, the enamel surface of control groups showed smooth surface in general with some scattered clear scratches due to the polishing procedure. The specimens bleached in group 2 and group 3, represented areas of mild erosion. Bleaching with 38% Hydrogen Peroxide (HP) and 16% Carbamide Peroxide (CP) resulted in mild changes in surface micro-morphology of enamel.

  15. Does the hearing sensitivity in thorny catfishes depend on swim bladder morphology?

    Directory of Open Access Journals (Sweden)

    Angelika Zebedin

    Full Text Available BACKGROUND: Thorny catfishes exhibit large variations in swim bladder morphology. These organs are of different sizes, forms and may have simple or branched diverticula. The swim bladder plays an important role in otophysans because it enhances their hearing sensitivity by transmitting sound pressure fluctuations via ossicles to the inner ear. METHODOLOGY/PRINCIPAL FINDINGS: To investigate if a form-function relationship exists, the swim bladder morphology and hearing ability were analyzed in six species. The morphology was quantified by measuring the length, width and height and calculating a standardized swim bladder length (sSBL, which was then used to calculate the relative swim bladder length (rSBL. Hearing was measured using the auditory evoked potential (AEP recording technique. Two species had simple apple-shaped and four species heart-shaped (cordiform bladders. One of the latter species had short unbranched diverticula on the terminal margin, two had a secondary bladder and two had many long, branched diverticula. The rSBL differed significantly between most of the species. All species were able to detect frequencies between 70 Hz and 6 kHz, with lowest thresholds found between 0.5 and 1 kHz (60 dB re 1 µPa. Hearing curves were U-shaped except in Hemidoras morrisi in which it was ramp-like. Mean hearing thresholds of species possessing smaller rSBLs were slightly lower (maximum 8.5 dB than those of species having larger rSBLs. CONCLUSIONS/SIGNIFICANCE: The current findings reveal a relationship between swim bladder form and its function among thorny catfishes. Relatively smaller swim bladders resulted in relatively better hearing. This is in contrast to a prior inter-familial study on catfishes in which species with large unpaired bladders possessed higher sensitivity at higher frequencies than species having tiny paired and encapsulated bladders.

  16. Morphology, stresses, and surface reactivity of nanoporous gold synthesized from nanostructured precursor alloys

    Science.gov (United States)

    Rouya, Eric

    Nanoporous metallic materials (NMMs) are generally synthesized using dealloying, whereby the more reactive component is dissolved from a homogeneous alloy in a suitable electrolyte, and the more noble metal atoms simultaneously diffuse into 3-D clusters, forming a bi-continuous network of interconnected ligaments. Nanoporous gold (NPG) in particular is a well-known NMM; it is inert, bio-compatible, and capable of developing large surface areas with 1--100nm pores. While several studies have demonstrated its potential usefulness in fuel cell and sensing devices, its structural, mechanical, and electrocatalytic properties still require further investigation, particularly if NPG is synthesized from precursor alloy films exhibiting metastable nanostructures. In this dissertation, the electrodeposition (ECD) process, microstrucural characteristics, and metatstability of Au-Ni precursor alloys are investigated. The stresses evolved during Au-Ni alloy nucleation and growth are investigated in situ and correlated with microstructural and electrochemical data in order to identify the various stress-inducing mechanisms. In situ stresses generated during Au-Ni and Au-Ag dealloying were investigated, and additionally correlated with the growth stresses. Finally, the surface area and electrocatalytic properties of NPG are characterized using a variety of electrochemical techniques. Potentiostatically electrodeposited Au1-x-Nix (x: 0--90at%) films form a continuous series of metastable solid solutions and exhibit a nanocrystalline morphology, with ˜10--20 nm grains, the size of which decreases with increasing Ni content. The formation of a metastable structure was interpreted in terms of the limited surface diffusivities of adatoms at the growing interface and atomic volume differences (˜15%). Internal stresses generated during ECD of Ni-rich films can be explained assuming a 3-D Volmer-Weber growth mode, where the stress is initially compressive, then transitions into tension

  17. Effect of hydrolyzed whey protein on surface morphology, water sorption, and glass transition temperature of a model infant formula.

    Science.gov (United States)

    Kelly, Grace M; O'Mahony, James A; Kelly, Alan L; O'Callaghan, Donal J

    2016-09-01

    Physical properties of spray-dried dairy powders depend on their composition and physical characteristics. This study investigated the effect of hydrolyzed whey protein on the microstructure and physical stability of dried model infant formula. Model infant formulas were produced containing either intact (DH 0) or hydrolyzed (DH 12) whey protein, where DH=degree of hydrolysis (%). Before spray drying, apparent viscosities of liquid feeds (at 55°C) at a shear rate of 500 s(-1) were 3.02 and 3.85 mPa·s for intact and hydrolyzed infant formulas, respectively. On reconstitution, powders with hydrolyzed whey protein had a significantly higher fat globule size and lower emulsion stability than intact whey protein powder. Lactose crystallization in powders occurred at higher relative humidity for hydrolyzed formula. The Guggenheim-Anderson-de Boer equation, fitted to sorption isotherms, showed increased monolayer moisture when intact protein was present. As expected, glass transition decreased significantly with increasing water content. Partial hydrolysis of whey protein in model infant formula resulted in altered powder particle surface morphology, lactose crystallization properties, and storage stability. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

  18. Surface structural, morphological, and catalytic studies of homogeneously dispersed anisotropic Ag nanostructures within mesoporous silica

    Energy Technology Data Exchange (ETDEWEB)

    Sareen, Shweta [Thapar University, School of Chemistry and Biochemistry (India); Mutreja, Vishal [Maharishi Markandeshwar University, Department of Chemistry (India); Pal, Bonamali; Singh, Satnam, E-mail: ssingh@thapar.edu [Thapar University, School of Chemistry and Biochemistry (India)

    2016-11-15

    Highly dispersed anisotropic Ag nanostructures were synthesized within the channels of 3-aminopropyltrimethoxysilane (APTMS)-modified mesoporous SBA-15 for catalyzing the reduction of p-dinitrobenzene, p-nitrophenol, and p-nitroacetophenone, respectively. A green templating process without involving any reducing agent, by varying the amount (1–10 wt.%) of Ag loading followed by calcination at 350 °C under H{sub 2} led to change in the morphology of Ag nanoparticles from nanospheres (~7–8 nm) to nanorods (aspect ratio ~12–30 nm) without any deformation in mesoporous sieves. In comparison to white bare SBA-15, gray-colored samples were formed with Ag impregnation exhibiting absorption bands at 484 and 840 nm indicating the formation of anisotropic Ag nanostructures within mesoporous matrix. TEM and FE-SEM micrographs confirmed the presence of evenly dispersed Ag nanostructures within as well as on the surface of mesoporous matrix. AFM studies indicated a small decrease in the average roughness of SBA-15 from 20.59 to 19.21 nm for 4 wt.% Ag/m-SBA-15, illustrating the encapsulation of majority of Ag nanoparticles in the siliceous matrix and presence of small amount of Ag nanoparticles on the mesoporous support. Moreover, due to plugging of mesopores with Ag, a significant decrease in surface area from 680 m{sup 2}/g of SBA-15 to 385 m{sup 2}/g was observed. The Ag-impregnated SBA-15 catalyst displayed superior catalytic activity than did bare SBA-15 with 4 wt.% Ag-loaded catalyst exhibiting optimum activity for selective reduction of p-nitrophenol to p-aminophenol (100 %), p-nitroacetophenone to p-aminoacetophenone (100 %), and p-dinitrobenzene to p-nitroaniline (87 %), with a small amount of p-phenylenediamine formation.

  19. [Acetabular morphological analysis in patients with high dislocated DDH using three-dimensional surface reconstruction technique].

    Science.gov (United States)

    Zengy, Yi; Min, Li; Lai, Ou-jie; Shen, Bin; Yang, Jing; Zhou, Zong-ke; Kang, Peng-de; Pei, Fu-xing

    2015-03-01

    To simulate acetabular morphology and perform acetabular quantitative analysis in high dislocated developmental dysplasia of the hip (DDH) patients using three-dimensional (3D) surface reconstruction technique, in order to understand the acetabular anatomic features and develop operative strategies for acetabular reconstruction. 3D pelvic images were reconstructed by Mimics software from CT data of 13 patients (13 hips) with high developmental DDH and 13 normal persons (26 hips). True acetabular superior-inferior diameter, anterior-posterior diameter, acetabular depth, medial wall thickness, abduction angle and anteversion angle were measured and compared between the two groups of participants. Irregular acetabular shape was found in high dislocated group, showing a triangle with wide upper and narrow lower. The acetabular quantitative analysis revealed (38.29 +/- 2.71) mm superior-inferior diameter, (21.74 +/- 5.33) mm anterior-posterior diameter, (15.50 +/- 2.93) mm acetabular depth, (6.80 +/- 2.97) mm medial wall thickness, (49.29 +/- 7.40) degrees abduction angle and (23.82 +/- 11.21) degrees anteversion angle in high dislocated patients. The superior-inferior diameter, anterior-posterior diameter and acetabular depth of high dislocated patients were significantly smaller than those of the normal contirols (PDDH patients have acetabular features: irregular shape, lower opening, higher medial wall and bigger abduction and anteversion angles. Joint arthroplasty surgery in high dislocated DDH patients needs to look at these acetabular features.

  20. Heat treatment effects on the surface morphology and optical properties of ZnO nanostructures

    Energy Technology Data Exchange (ETDEWEB)

    Zainizan Sahdan, M. [Faculty of Electrical Engineering, Universiti Teknologi MARA, 40450 Shah Alam, Selangor (Malaysia); Faculty of Electrical and Electronics Engineering, Universiti Tun Hussein onn Malaysia, 86400 Batu Pahat, Johor (Malaysia); Hafiz Mamat, M.; Salina, M.; Noor, Uzer M.; Rusop, Mohamad [Faculty of Electrical Engineering, Universiti Teknologi MARA, 40450 Shah Alam, Selangor (Malaysia); Khusaimi, Zuraida [Faculty of Applied Sciences, Universiti Teknologi MARA, 40450 Shah Alam, Selangor (Malaysia)

    2010-09-15

    Zinc oxide (ZnO) nanostructures have received broad attention due to its wide applications especially for thin-film solar cells and transistors. In this paper, we report the effects of heat treatment on the structural and optical properties of ZnO nanostructures. Zinc oxide nanostructures were synthesized using thermal chemical vapour deposition (CVD) method on glass substrate. The surface morphologies which were observed by scanning electron microscope (SEM) show that ZnO nanostructures change its shape and size when the annealing temperature increases from 400 C to 600 C. Structural measurement using X-ray diffraction (XRD) has shown that ZnO nanostructures have the highest crystallinity and smallest crystallite size (20 nm) when annealed at 550 C. Furthermore, the samples were optically characterized using Photoluminescence (PL) spectrometer. The PL spectra indicate that ZnO nanostructures have the highest peak at UV wavelength when annealed at 550 C. The mechanism of the PL properties of ZnO nanostructures is also discussed. We conclude that ZnO nanostructures deposited using thermal CVD have the optimum structural and PL properties when annealed at 550 C. (copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  1. Determination of surface morphology of TiO2 nanostructure using synchrotron radiation

    Science.gov (United States)

    Das, Gangadhar; Kumar, Manoj; Biswas, A. K.; Khooha, Ajay; Mondal, Puspen; Tiwari, M. K.

    2017-05-01

    Nanostructures of Titanium oxide (TiO2) are being studied for many promising applications, e.g., solar photovoltaics, solar water splitting for H2 fuel generation etc., due to their excellent photo-catalytic properties. We have synthesized low-dimensional TiO2 nanoparticles by gas phase CW CO2 laser pyrolysis. The laser synthesis process has been optimized for the deposition of highly pure, nearly mono-dispersed TiO2 nanoparticles on silicon substrates. Hard x-ray standing wave-field (XSW) measurements in total reflection geometry were carried out on the BL-16 beamline of Indus-2 synchrotron radiation facility in combination with x-ray reflectivity and grazing incidence x-ray fluorescence measurements for the determination of surface morphology of the deposited TiO2 nanostructures. The average particle size of TiO2 nanostructure estimated using transmission electron microscopy (TEM) was found to closely agree with the XSW and grazing incidence x-ray diffraction (GIXRD) results.

  2. Role of nanoclay shape and surface characteristics on the morphology and thermal properties of polystyrene nanocomposites synthesized via emulsion polymerization

    CSIR Research Space (South Africa)

    Greesh, N

    2013-10-01

    Full Text Available This work evaluates the role of the surface properties and shape of clay type on the morphology, thermal, and thermo-mechanical properties of the polystyrene (PS)/clay nanocomposites prepared via free-radical emulsion polymerization. Attapulgite...

  3. Micro-morphology of single crystalline silicon surfaces during anisotropic wet chemical etching in KOH: velocity source forests

    NARCIS (Netherlands)

    van Veenendaal, E.; Sato, K.; Shikida, M.; Shikida, M.; Nijdam, A.J.; van Suchtelen, J.

    2001-01-01

    For silicon etched in KOH the micro-morphology of any surface, no matter the crystallographic orientation, is defined by some sort of persistent corrugations. As a matter of principle, the occurrence of these corrugations is incompatible with the classical kinematic wave theory for the evolution of

  4. SU-F-T-661: Dependence of Gold Nano Particles Cluster Morphology On Dose Enhancement of Photon Radiation Therapy Apply for Radiation Biology Effect

    Energy Technology Data Exchange (ETDEWEB)

    Ahn, S [Department of Health Sciences and Technology, Samsung Advanced Institute for Health Sciences and Technology, Sungkyunkwan University (Korea, Republic of); Chung, K; Han, Y; Park, H [Samsung Medical Center, Sungkyunkwan University School of Medicine radiation oncology (Korea, Republic of)

    2016-06-15

    Purpose: Injected gold nano particles (GNPs) to a body for dose enhancement are known to form in the tumorcell cluster morphology. We investigated the dependence of dose enhancement on the morphology characteristic with an approximated morphology model by using Monte Carlo simulations. Methods: For MC simulation, TOPAS version 2.0P-03 was used. GNP cluster morphology was approximated as a body center cubic(BCC) model by placing 8 GNPs at the corner and one at the center of cube with length from 2.59 µm to 0.25 µm located in a 4 µm length water filled cube phantom. 4 µm length square shaped beams of poly-energetic 50, 260 kVp photons were irradiated to the water filled cube phantom with 100 nm diameter GNPs in it. Dose enhancement ratio(DER) was computed as a function of distance from the surface of the GNP at the cube center for 18 cubes geometries. For scoring particles, 10 nm width of concentric shell shaped detector was constructed up to 100 nm from the center. Total dose in a sphere of 100 nm radius of detector were normalized to 2.59 µm length cube morphology. To verified biological effect of BCC model applied to cell survival curve fitting. Results: DER increase as the distance of the GNPs reduces. DER was largest for 0.25 µm length cube. Dependence of GNP distance DER increment was 1.73, 1.60 for 50 kVp, 260 kVp photons, respectively. Also, Using BCC model applied to cell survival curve was well prediction. Conclusion: DER with GNPs was larger when they are closely packed in the phantom. Therefore, better therapeutic effects can be expected with close-packed GNPs. This research was supported by the NRF funded by the Ministry of Science, ICT & Future Planning (2012M3A9B6055201 and 2012R1A1A2042414), Samsung Medical Center grant[GFO1130081].

  5. Surface morphology evolution with fabrication parameters of ZnO nanowires toward emission properties enhancement

    Science.gov (United States)

    Belhaj, Marwa; Dridi, Cherif; Habba, Yamina Ghozlene; Capo-Chichi, Martine; Leprince-Wang, Yamin

    2017-12-01

    ZnO nanowire (NW) arrays were successfully grown on pre-seeded indium Tin oxide (ITO)-coated glass substrate using hydrothermal synthesis. Herein, the effects of ZnO seed layer density on the performance of ZnO NWs were investigated in details. The orientation and the dimension of ZnO NWs were found to depend on seeded substrate density as shown by scanning electron microscopy (SEM) micrographs which revealed that the typical morphology with the most uniform size can be obtained. From the X-ray diffraction (XRD) measurement, it can be seen that hexagonal c -axis oriented NWs were grown. The resonant Raman scattering was also investigated in details. It confirmed the wurtzite structure of the NW arrays and expected for good optical properties. The optical band gaps of synthesized ZnO NWs were found to decrease comparing to bulk ZnO and as function of seed layer. The photoluminescence (PL) spectra at room temperature have shown strong UV excitonic emission and weak deep-level emissions which reveal that the as-grown NW arrays have good optical properties with limited deep-level defects.

  6. Use of digital image analysis combined with fractal theory to determine particle morphology and surface texture of quartz sands

    Directory of Open Access Journals (Sweden)

    Georgia S. Araujo

    2017-12-01

    Full Text Available The particle morphology and surface texture play a major role in influencing mechanical and hydraulic behaviors of sandy soils. This paper presents the use of digital image analysis combined with fractal theory as a tool to quantify the particle morphology and surface texture of two types of quartz sands widely used in the region of Vitória, Espírito Santo, southeast of Brazil. The two investigated sands are sampled from different locations. The purpose of this paper is to present a simple, straightforward, reliable and reproducible methodology that can identify representative sandy soil texture parameters. The test results of the soil samples of the two sands separated by sieving into six size fractions are presented and discussed. The main advantages of the adopted methodology are its simplicity, reliability of the results, and relatively low cost. The results show that sands from the coastal spit (BS have a greater degree of roundness and a smoother surface texture than river sands (RS. The values obtained in the test are statistically analyzed, and again it is confirmed that the BS sand has a slightly greater degree of sphericity than that of the RS sand. Moreover, the RS sand with rough surface texture has larger specific surface area values than the similar BS sand, which agree with the obtained roughness fractal dimensions. The consistent experimental results demonstrate that image analysis combined with fractal theory is an accurate and efficient method to quantify the differences in particle morphology and surface texture of quartz sands.

  7. Evolution effects of the copper surface morphology on the nucleation density and growth of graphene domains at different growth pressures

    Science.gov (United States)

    Hedayat, Seyed Mahdi; Karimi-Sabet, Javad; Shariaty-Niassar, Mojtaba

    2017-03-01

    In this work, we study the influence of the surface morphology of the catalytic copper substrate on the nucleation density and the growth rate of graphene domains at low and atmospheric pressure chemical vapor deposition (LPCVD and APCVD) processes. In order to obtain a wide range of initial surface morphology, precisely controlled electropolishing methods were developed to manipulate the roughntreess value of the as-received Cu substrate (RMS = 30 nm) to ultra-rough (RMS = 130 nm) and ultra-smooth (RMS = 2 nm) surfaces. The nucleation and growth of graphene domains show obviously different trends at LPCVD and APCVD conditions. In contrast to APCVD condition, the nucleation density of graphene domains is almost equal in substrates with different initial roughness values at LPCVD condition. We show that this is due to the evolution of the surface morphology of the Cu substrate during the graphene growth steps. By stopping the surface sublimation of copper substrate in a confined space saturated with Cu atoms, the evolution of the Cu surface was impeded. This results in the reduction of the nucleation density of graphene domains up to 24 times in the pre-smoothed Cu substrates at LPCVD condition.

  8. Morphology of the occlusal surfaces of premolar and molar teeth as an indicator of age in the horse.

    Science.gov (United States)

    Carmalt, J L; Allen, A L

    2008-09-01

    The purpose of this study was to investigate the use of cheek tooth occlusal surface morphology as an indicator of age in the horse using a blinded cross-sectional design. Twenty horses of varying age, breed and sex were used. Horses of known age (foaling date) were euthanized for reasons other than dental disease. Following disarticulation of the head and sectioning of the mandibles, cheek teeth were cleaned using running water and photographs were taken of each arcade. Using a computer-based program, the total surface area of each premolar and molar, the outer enamel ridge perimeter distance, infundibular surface areas and perimeter distances were measured. Further anatomical data were calculated from these measurements and a statistical analysis of the relationship between horse age and cheek tooth occlusal morphology was performed. Results indicated that multiple anatomical regions within the occlusal surface of the equine cheek tooth can be used as an indicator of age. There are important differences between mandibular and maxillary teeth as well as between teeth in the same dental arcade. Horse size is also of significance. The mesial infundibular surface area as a percentage of the total surface area of tooth 111, and the mesiodistal length of 1/2/3/4 09 teeth, most closely approximates age within our mathematical model. Cheek tooth morphological data can be used to predict age in horses that possess all their permanent dentition. In cases in which the age of horses cannot be accurately determined from incisor examination, cheek teeth may be used.

  9. Physical and morphological properties of z ~ 3 Lyman break galaxies: dependence on Lyα line emission

    Science.gov (United States)

    Pentericci, L.; Grazian, A.; Scarlata, C.; Fontana, A.; Castellano, M.; Giallongo, E.; Vanzella, E.

    2010-05-01

    Aims: We investigate the physical and morphological properties of Lyman break galaxies (LBGs) at redshift ~2.5 to ~3.5, to determine if and how they depend on the nature and strength of the Lyα emission. Methods: We selected U-dropout galaxies from the z-detected GOODS-MUSIC catalog by adapting the classical Lyman break criteria on the GOODS filter set. We kept only those galaxies with spectroscopic confirmation, mainly from VIMOS and FORS public observations. Using the full multi-wavelength 14-bands information (U to IRAC), we determined the physical properties of the galaxies through a standard spectral energy distribution fitting procedure with the updated Charlot & Bruzual (2009) templates. We also added other relevant observations of the GOODS field, i.e. the 24 μm observations from Spitzer/MIPS and the 2 MSec Chandra X-ray observations. Finally, using non parametric diagnostics (Gini, Concentration, Asymmetry, M20 and ellipticity), we characterized the rest-frame UV morphologies of the galaxies. We then analyzed how these physical and morphological properties correlate with the presence of the Lyα emission line in the optical spectra. Results: We find that unlike at higher redshift, the dependence of physical properties on the Lyα line is milder: galaxies without Lyα in emission tend to be more massive and dustier than the rest of the sample, but all other parameters, ages, star formation rates (SFR), X-ray emission and UV morphology do not depend strongly on the presence of the Lyα emission. A simple scenario where all LBGs have intrinsically high Lyα emission, but where the dust and neutral hydrogen content (which shapes the final appearance of the Lyα) depend on the mass of the galaxies, is able to reproduce the majority of the observed properties at z˜3. Some modification might be needed to account for the observed evolution of these properties with cosmic epoch, which is also discussed.

  10. Rheology, Morphology and Temperature Dependency of Nanotube Networks in Polycarbonate/Multiwalled Carbon Nanotube Composites

    International Nuclear Information System (INIS)

    Abbasi, Samaneh; Carreau, Pierre J.; Derdouri, Abdessalem

    2008-01-01

    We present several issues related to the state of dispersion and rheological behavior of polycarbonate/multiwalled carbon nanotube (MWCNT) composites. The composites were prepared by diluting a commercial masterbatch containing 15 wt% nanotubes using optimized melt-mixing conditions. The state of dispersion was then analyzed by scanning and transmission electron microscopy (SEM, TEM). Rheological characterization was also used to assess the final morphology. Further, it was found that the rheological percolation threshold decreased significantly with increasing temperature and finally reached a constant value. This is described in terms of the Brownian motion, which increases with temperature. However, by increasing the nanotube content, the temperature effects on the complex viscosity at low frequency decreased significantly. Finally, the percolation thresholds were found to be approximately equal to 0.3 and 2 wt% for rheological and electrical conductivity measurements, respectively

  11. Quantitative study of temperature-dependent order in thin films of cylindrical morphology block copolymer

    Science.gov (United States)

    Mishra, Vindhya; Kramer, Edward

    2010-03-01

    Disordering and defect generation in block copolymer systems at high temperatures is of significance to get a better understanding of the physics governing these systems, which can also direct efforts to minimize them. We have studied the smectic-nematic-isotropic transition in confined monolayers and bilayers of cylindrical morphology poly (styrene-b-2vinyl pyridine) diblock copolymer. Previous studies of melting phenomena in block copolymer thin films have relied on quantitative AFM studies alone. We have supplemented AFM studies with grazing incidence small angle X-ray diffraction lineshape analysis to quantify the decay of translational and orientational order with increasing temperature. The results have been interpreted in the context of the Toner-Nelson theory of melting for layered systems.

  12. On the Emittance dependence on anode morphology of laser induced ion beams

    International Nuclear Information System (INIS)

    Velardi, L; Delle Side, D; Nassisi, V

    2014-01-01

    In this work, we studied the characteristics of ion beams generated by PLATONE accelerator in different anode configurations. The accelerator is a laser ion source with two gaps which accelerate the ions in cascade. The laser is an excimer KrF able to work at irradiances of 10 8 -10 10 W/cm 2 . The target ablated was disk of Cu. The accelerating voltage applied in this work was 60 kV. The emittance evaluation was performed by the pepper pot method utilising radio-chromic films, EBT Gafchromic, as sensible targets. The study was performed by varying the geometric configuration of the anode (the extracting electrode), modifying the hole morphology. A plane and curved grids were mounted in order to change the extraction configuration. The results were compared with the ones obtained with the extraction hole without any grid. For the normalized emittance the lowest value found was 0.20 π mm mrad.

  13. Effects of scaffold surface morphology on cell adhesion and survival rate in vitreous cryopreservation of tenocyte-scaffold constructs

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Zhi [State Key Laboratory of Biotherapy, West China Hospital of Sichuan University, Chengdu 610041 (China); Department of Bone and Joint Surgery, The affiliated hospital of Luzhou Medical College, Luzhou 646000 (China); Qing, Quan [Sichuan College of Traditional Chinese Medicine, Mianyang 621000 (China); Regenerative Medicine Research Center, West China Hospital of Sichuan University, Chengdu 610041 (China); Chen, Xi; Liu, Cheng-Jun; Luo, Jing-Cong [State Key Laboratory of Biotherapy, West China Hospital of Sichuan University, Chengdu 610041 (China); Hu, Jin-Lian [Institute of Textiles and Clothing, The Hong Kong Polytechnic University, Hong Kong (China); Qin, Ting-Wu, E-mail: tingwuqin@hotmail.com [State Key Laboratory of Biotherapy, West China Hospital of Sichuan University, Chengdu 610041 (China)

    2016-12-01

    Highlights: • The shapes of tenocytes varied when seeded on different surface of scaffolds. • Tenocytes were flat on smooth surface and spindle on micro-grooved surface. • Tenocytes were ellipse or spindle on porous surface. • Tenocytes got varying adhesion shape and elongation index on varying surfaces. • The tenocyte survival on porous surface was superior to the other two groups. - Abstract: The purpose of this study was to investigate the effects of scaffold surface morphology on cell adhesion and survival rate in vitreous cryopreservation of tenocyte-scaffold constructs. Tenocytes were obtained from tail tendons of rats. Polydimethylsiloxane (PDMS) was used to fabricate three types of scaffolds with varying surface morphological characteristics, i.e., smooth, micro-grooved, and porous surfaces, respectively. The tenocytes were seeded on the surfaces of the scaffolds to form tenocyte-scaffold constructs. The constructs were cryopreserved in a vitreous cryoprotectant (CPA) with a multi-step protocol. The cell adhesion to scaffolds was observed with electronic scanning microscopy (SEM). The elongation index of the living tenocytes and ratio of live/dead cell number were examined based on a live/dead dual fluorescent staining technique, and the survival rate of tenocytes was studied with flow cytometry (FC). The results showed the shapes of tenocytes varied between the different groups: flat or polygonal (on smooth surface), spindle (on micro-grooved surface), and spindle or ellipse (on porous surface). After thawing, the porous surface got the most living tenocytes and a higher survival rate, suggesting its potential application for vitreous cryopreservation of engineered tendon constructs.

  14. Gas morphology and energetics at the surface of PDRs : New insights with Herschel observations of NGC 7023

    NARCIS (Netherlands)

    Joblin, C.; Pilleri, P.; Montillaud, J.; Fuente, A.; Gerin, M.; Berne, O.; Ossenkopf, V.; Le Bourlot, J.; Teyssier, D.; Goicoechea, J. R.; Le Petit, F.; Roellig, M.; Akyilmaz, M.; Benz, A. O.; Boulanger, F.; Bruderer, S.; Dedes, C.; France, K.; Guesten, R.; Harris, A.; Klein, T.; Kramer, C.; Lord, S. D.; Martin, P. G.; Martin-Pintado, J.; Mookerjea, B.; Okada, Y.; Phillips, T. G.; Rizzo, J. R.; Simon, R.; Stutzki, J.; van der Tak, F.; Yorke, H. W.; Steinmetz, E.; Jarchow, C.; Hartogh, P.; Honingh, C. E.; Siebertz, O.; Caux, E.; Colin, B.

    2010-01-01

    Context. We investigate the physics and chemistry of the gas and dust in dense photon-dominated regions (PDRs), along with their dependence on the illuminating UV field. Aims: Using Herschel/HIFI observations, we study the gas energetics in NGC 7023 in relation to the morphology of this nebula. NGC

  15. Rat-strain dependent changes of dendritic and spine morphology in the hippocampus after cocaine self-administration.

    Science.gov (United States)

    Selvas, Abraham; Coria, Santiago M; Kastanauskaite, Asta; Fernaud-Espinosa, Isabel; DeFelipe, Javier; Ambrosio, Emilio; Miguéns, Miguel

    2017-01-01

    We previously showed that cocaine self-administration increases spine density in CA1 hippocampal neurons in Lewis (LEW) but not in Fischer 344 (F344) rats. Dendritic spine morphology is intimately related to its function. Thus, we conducted a 3D morphological analysis of CA1 dendrites and dendritic spines in these two strains of rats. Strain-specific differences were observed prior to cocaine self-administration: LEW rats had significantly larger dendritic diameters but lower spine density than the F344 strain. After cocaine self-administration, proximal dendritic volume, dendritic surface area and spine density were increased in LEW rats, where a higher percentage of larger spines were also observed. In addition, we found a strong positive correlation between dendritic volume and spine morphology, and a moderate correlation between dendritic volume and spine density in cocaine self-administered LEW rats, an effect that was not evident in any other condition. By contrast, after cocaine self-administration, F334 rats showed decreased spine head volumes. Our findings suggest that genetic differences could play a key role in the structural plasticity induced by cocaine in CA1 pyramidal neurons. These cocaine-induced alterations could be related to differences in the memory processing of drug reward cues that could potentially explain differential individual vulnerability to cocaine addiction. © 2015 Society for the Study of Addiction.

  16. Quantification of morphological properties of terrace surface using digital elevation model and its application to stratigraphic correlation of terraces

    International Nuclear Information System (INIS)

    Yamamoto, Shinya; Hataya, Ryuta; Hamada, Takaomi

    2008-01-01

    Uplift estimation during late Quaternary is required for site selection of geological disposal facility of high level radioactive waste (NUMO, 2004). Terrace level and/or difference in elevation of terraces are good indicators of uplift. Therefore, a reliable method of terrace correlation and chronology is a key issues. Air-photograph interpretation is generally carried out in the early stage of a terrace investigation. However, a terrace classification often depends on the observer's qualitative interpretation. In order to improve objectivity of geomorphic investigation with air-photograph interpretation, we examine to quantify the morphological properties of terrace surface by some morphometric variables that are computed from Digital Elevation Model (DEM). In this study, four morphometric variables (average slope, average laplacian, remaining ratio of a terrace surface, and average depth of erosion) were calculated using data sets of terraces of which chronological data are clearly described. The relationship between these variables and terrace ages shows constant tendencies respond to the geomorphological process caused by the erosion. To examine capability of morphometric variables as an index of terrace correlation, regression analyses were carried out. The regression age estimated from morphometric variables allows to classify terraces in correct sequence, and the error with the observed age falls up to 100,000 years. In addition, to discuss appropriate quantities of DEM for terrace correlation, we used three different elevation data to create DEM: 1) aerial photogrammetry data; 2) airborne laser scanner data; 3) 1:25000-scale contour map. By comparing analysis results of each DEMs, we show suitable qualities of elevation data and DEM grid size to represent the degree of erosion correctly. (author)

  17. The dependence of lipid monolayer lipolysis on surface pressure.

    OpenAIRE

    Hall, D G

    1992-01-01

    Brönsted-Bjerrum theory [Brönsted (1922) Z. Phys. Chem. 102, 169-207; (1925) Z. Phys. Chem. 115, 337-364; Bjerrum (1924) Z. Phys. Chem. 108, 82-100] as applied to reactions at interfaces is used to interpret published data on the lipolysis of dinonanoyl phosphatidylcholine monolayers by pancreatic phospholipase A2. Reasonable quantitative agreement between theoretical and experimental results occurs when the reported effects of surface pressure on the amount of adsorbed enzyme are used togeth...

  18. The Tangent Conoids Family Which Depends on the Ruled Surface

    OpenAIRE

    Özyılmaz, E.

    1998-01-01

    In this study, a new congruence[A••] has been definedby putting a tangent right conoid on each line of a ruled surface (A1(s)) of a line congruence [A]. Then, by considering special case of the congruence [A••] which has been defined in the previous part, the concepts of tangent congruence, drall and the relation among Blaschke vectors of Blaschke trihedrons, having common line Ao has been examined for this special case. At the end of this study, the concept of tangent congruence for some spe...

  19. Field dependent surface resistance of niobium on copper cavities

    Directory of Open Access Journals (Sweden)

    T. Junginger

    2015-07-01

    Full Text Available The surface resistance R_{S} of superconducting cavities prepared by sputter coating a niobium film on a copper substrate increases significantly stronger with the applied rf field compared to cavities of bulk material. A possible cause is that the thermal boundary resistance between the copper substrate and the niobium film induces heating of the inner cavity wall, resulting in a higher R_{S}. Introducing helium gas in the cavity, and measuring its pressure as a function of applied field allowed to conclude that the inner surface of the cavity is heated up by less than 120 mK when R_{S} increases with E_{acc} by 100  nΩ. This is more than one order of magnitude less than what one would expect from global heating. Additionally, the effects of cooldown speed and low temperature baking have been investigated in the framework of these experiments. It is shown that for the current state of the art niobium on copper cavities there is only a detrimental effect of low temperature baking. A fast cooldown results in a lowered R_{S}.

  20. Observation on Surface Change of Fragile Glass: Temperature - Time Dependence Studied by X-Ray Reflectivity

    International Nuclear Information System (INIS)

    Kikkawa, Hiroyuki; Kitahara, Amane; Takahashi, Isao

    2004-01-01

    The structural change of a fragile glass surface close to the glass transition temperature Tg is studied by using X-ray reflectivity. Measurements were performed on surfaces of maltitol, which is a typical polyalcohol fragile glass with Tg = 320K. Upon both heating and cooling, we find the following features which are also noticed in silicate glass surfaces: (i) On heating, the surface morphology indicates a variation at temperatures below Tg; (ii) A drastic increase in surface roughness occurs at a temperature about 333K on heating, which is 13K higher than Tg; (iii) During the cooling of the sample, formation of a low-density surface layer (3nm at 293K) is observed. Prior to the crystallization, nm - μm sized domains were grown at the surface, which might not be reported for other glasses

  1. Nitrogen-induced changes in morphological development and bacterial susceptibility of belgian endive (Cichorium intybus L.) are genotype-dependent

    Science.gov (United States)

    Richard-Molard; Wuilleme; Scheel; Gresshoff; Morot-Gaudry; Limami

    1999-10-01

    Nitrogen is known to modulate plant development and resistance to pathogens. Four selected lines (Alg, NS1, NR1 and NR2) of chicory (Cichorium intybus L.) were grown on low (0.6 mM) and high (3 mM) NO(-)(3) nutrition in order to study the effect of N on the expression of three traits, namely, shoot/root ratio, chicon morphology and resistance to soft rot caused by Erwinia sp. For all genotypes, increasing N supply led to a higher shoot/root ratio, resulting from an increased shoot biomass but with no effect on root growth. In contrast, the effect of N on chicon morphology and resistance to bacteria was genotype-dependent and we distinguished two groups of lines according to their phenotypic characteristics. In the group consisting of NR1 and NR2, increasing NO(-)(3) supply during the vegetative phase made the chicon morphology switch from an opened to a closed type while resistance to bacteria was not affected by N supply. In the NS1 and Alg group, the effect of N on chicon morphology was the opposite to that observed in the NR1-NR2 group while NS1 and Alg exhibited a partial resistance to Erwinia sp. , only expressing soft-rot disease when the N supply reached 3 mM. Characterization by DNA amplification fingerprinting (DAF) allowed the generation of 110 polymorphic bands and confirmed that the lines NR1 and NR2, on the one hand, and NS1 and Alg, on the other hand, belong to two distinct genetic groups. The DAF results indicate that chicon morphology and partial resistance to Erwinia sp. are complex traits which would be amenable to quantitative trait loci analysis. The split growth phase of chicory means that any changes in chicon related to N supply during vegetative growth were mediated by a root-originating signal. No variation in root carbon content among genotypes and NO(-)(3) treatments was observed. In contrast, differences in root N content revealed the same grouping of the chicory lines, NR1 and NR2 being systematically richer in amino acids and NO(-)(3

  2. He-ion and self-atom induced damage and surface-morphology changes of a hot W target

    International Nuclear Information System (INIS)

    Meyer, F W; Hijazi, H; Bannister, M E; Dadras, J; Krstic, P S; Meyer, H M III; Parish, C M

    2014-01-01

    We report results of measurements on the evolution of the surface morphology of a hot tungsten surface due to impacting low-energy (80–12 000 eV) He ions and of simulations of damage caused by cumulative bombardment of 1 and 10 keV W self-atoms. The measurements were performed at the ORNL Multicharged Ion Research Facility, while the simulations were done at the Kraken supercomputing facility of the University of Tennessee. At 1 keV, the simulations show strong defect-recombination effects that lead to a saturation of the total defect number after a few hundred impacts, while sputtering leads to an imbalance of the vacancy and interstitial number. On the experimental side, surface morphology changes were investigated over a broad range of fluences, energies and temperatures for both virgin and pre-damaged W-targets. At the lowest accumulated fluences, small surface-grain features and near-surface He bubbles are observed. At the largest fluences, individual grain characteristics disappear in focused ion beam/scanning electron microscopy (FIB/SEM) scans, and the entire surface is covered by a multitude of near-surface bubbles with a broad range of sizes, and disordered whisker growth, while in top-down SEM imaging the surface is virtually indistinguishable from the nano-fuzz produced on linear plasma devices. These features are evident at progressively lower fluences as the He-ion energy is increased. (paper)

  3. Linking the operating parameters of chemical vapor deposition reactors with film conformality and surface nano-morphology.

    Science.gov (United States)

    Cheimarios, Nikolaos; Garnelis, Sokratis; Kokkoris, George; Boudouvis, Andreas G

    2011-09-01

    A multiscale modeling framework is used to couple the co-existing scales, i.e., macro-, micro- and nano-scale, in chemical vapor deposition (CVD) processes. The framework consists of a reactor scale model (RSM) for the description of the transport phenomena in the bulk phase (macro-scale) of a CVD reactor and two models for the micro- and nano-scale: (a) A feature scale model (FSM) describing the deposition of a film inside features on a predefined micro-topography on the wafer and (b) a nano-morphology model (NMM) describing the surface morphology evolution during thin film deposition on an initially flat surface. The FSM is deterministic and consists of three sub-models: A ballistic model for the species' transport inside features, a surface chemistry model, and a profile evolution algorithm based on the level set method. The NMM is stochastic and is based on the kinetic Monte Carlo method. The coupling of RSM with FSM is performed through a correction of the species consumption on the wafer. The linking of RSM with NMM is performed through "feeding" of the deposition rate calculated by RSM to the NMM. The case study is CVD of Silicon (Si) from Silane. The effect of the reactor's operating parameters on the Si film conformality inside trenches is investigated by the coupling of RSM with FSM. The formation of dimmers on an initially flat Si (001) surface as well as the periodic change of the surface nano-morphology is predicted.

  4. Effects of etching time on the bottom surface morphology of ultrathin porous alumina membranes for use as masks

    Science.gov (United States)

    Yang, Sun A.; Choi, Yong Chan; Bu, Sang Don

    2012-11-01

    We investigated the effect of etching time on the bottom surface morphologies of ultrathin porous alumina membranes (UT-PAMs) anodized in oxalic and phosphoric acid. The morphology of the bottom surface clearly changed and a unique surface undulation was observed during the etching process. Such an undulation regarding the bottom surface is attributed to the different etching rates between the dome-shaped barrier layer and the hexagonal cell walls. The results suggest that the bottom morphology of UT-PAMs formed after the barrier layer is opened significantly affects the contact area of the bottom side with the substrate. During the initial stage of the opening process for the barrier layer, the porous section will contact the substrate rather than the walls. However, as the etching time increases, the height of the porous section becomes considerably lower than that of the walls, which means that the walls will contact the substrate with a gap between the pores and the substrate. Based on our experimental results, we propose a possible schematic diagram describing the effects of UT-PAMs with differently-shaped bottom surfaces on the shapes of fabricated nanodots when the UT-PAMs are used as masks.

  5. Affecting the morphology of silver deposition on carbon nanotube surface: From nanoparticles to dendritic (tree-like) nanostructures

    Energy Technology Data Exchange (ETDEWEB)

    Forati-Nezhad, Mohsen [Department of Polymer Engineering and Color Technology, Amirkabir University of Technology, Tehran (Iran, Islamic Republic of); Mir Mohamad Sadeghi, Gity, E-mail: gsadeghi@aut.ac.ir [Department of Polymer Engineering and Color Technology, Amirkabir University of Technology, Tehran (Iran, Islamic Republic of); Yaghmaie, Frank [Northern California Nanotechnology Center, University of California, Davis, CA 95616 (United States); Alimohammadi, Farbod [Young Researchers and Elite Club, South Tehran Branch, Islamic Azad University, Tehran (Iran, Islamic Republic of)

    2015-01-01

    Chemical reduction was used to synthesize silver crystals on the surface of multiwall carbon nanotubes (MWCNTs) in the presence of acetone, N,N-dimethylformamide (DMF), N-methyl-2-pyrrolidone, and isopropyl alcohol as solvent. DMF and sodium dodecyl sulfate were used as a reducing and a stabilizing agent, respectively. The structure and nature of hybrid MWCNT/silver were characterized by Raman spectroscopy, FTIR spectroscopy, transmission electron microscopy (TEM), and field emission scanning electron microscope (FESEM). The presence of silver crystals on the nanotubes was confirmed by XRD. The results show the formation of silver crystals on the MWCNT surface and indicate that the morphology of silver crystals can be control by changing the solvent. The type of solvent is an effective parameter that affects the particle size and morphological transition from nanoparticles to silver trees. - Highlights: • The silver crystals are grown on the CNT surface by chemical reduction method. • The morphology of silver crystals is controlled by changing the solvent. • Silver nanoparticles and dendritic nanostructures on CNT surface are achieved. • Any change in structure and surface defects by synthesis condition is investigated.

  6. Surface Morphology and Corrosion Behavior of Hydroxyapatite-Coated Co-Cr Implant: Effect of Sintering Conditions

    Science.gov (United States)

    Shirdar, Mostafa Rezazadeh; Taheri, Mohammad Mahdi

    2017-12-01

    The surface morphology and corrosion behavior of a hydroxyapatite (HA)-coated cobalt-chromium (Co-Cr) implant after sintering posttreatment using different times and temperatures were investigated. The substrates were electrophoretically coated with calcium phosphate in solution of Ca(NO3)·4H2O and NH4H2PO4. Sintering at four different conditions was then performed on the as-deposited samples. Scanning electron microscopy, contact angle measurement, and potentiodynamic polarization studies were employed to investigate the surface morphology, porosity, wettability, and corrosion behavior of the coated samples. The results revealed that the HA-coated substrate sintered at temperature of 600°C for 20 min showed fairly uniform microstructure with the highest density and corrosion resistance compared with the other conditions. Moreover, the highest wettability was exhibited by the HA surface sintered at temperature of 500°C for 60 min.

  7. Tubular lysosome morphology and distribution within macrophages depend on the integrity of cytoplasmic microtubules

    International Nuclear Information System (INIS)

    Swanson, J.; Bushnell, A.; Silverstein, S.C.

    1987-01-01

    Pinocytosis of the fluorescent dye lucifer yellow labels elongated, membrane-bound tubular organelles in several cell types, including cultured human monocytes, thioglycolate-elicited mouse peritoneal macrophages, and the macrophage-like cell line J774.2. These tubular structures can be identified as lysosomes by acid phosphatase histochemistry and immunofluorescence localization of cathepsin L. The abundance of tubular lysosomes is markedly increased by treatment with phorbol 12-myristate 13-acetate. When labeled by pinocytosis of microperoxidase and examined by electron microscopic histochemistry, the tubular lysosomes have an outside diameter of ≅ 75 nm and a length of several micrometers; they radiate from the cell's centrosphere in alignment with cytoplasmic microtubules and intermediate filaments. Incubation of phorbol myristate acetate-treated macrophages at 4 0 C or in medium containing 5 μM colchicine or nocodazole at 37 0 C leads to disassembly of microtubules and fragmentation of the tubular lysosomes. Return of the cultures to 37 0 C or removal of nocodazole from the medium leads to reassembly of microtubules and the reappearance of tubular lysosomes within 10-20 min. The authors conclude that microtubules are essential for the maintenance of tubular lysosome morphology and that, in macrophages, a significant proportion of the lysosomal compartment is contained within these tubular structures

  8. VOPcPhO:P3HT composite micro-structures with nano-porous surface morphology

    Energy Technology Data Exchange (ETDEWEB)

    Azmer, Mohamad Izzat [Low Dimensional Materials Research Centre (LDMRC), Department of Physics, Faculty of Science, University of Malaya, 50603 Kuala Lumpur (Malaysia); Ahmad, Zubair, E-mail: zubairtarar@qu.edu.qa [Center for Advanced Materials (CAM), Qatar University, P. O. Box 2713, Doha (Qatar); Sulaiman, Khaulah, E-mail: khaulah@um.edu.my [Low Dimensional Materials Research Centre (LDMRC), Department of Physics, Faculty of Science, University of Malaya, 50603 Kuala Lumpur (Malaysia); Touati, Farid [Department of Electrical Engineering, College of Engineering, Qatar University, P. O. Box 2713, Doha (Qatar); Bawazeer, Tahani M. [Department of Chemistry, Faculty of Applied Science, Umm Al-Qura University, Makkah (Saudi Arabia); Alsoufi, Mohammad S. [Mechanical Engineering Department, College of Engineering and Islamic Architecture, Umm Al-Qura University, Makkah (Saudi Arabia)

    2017-03-31

    Highlights: • VOPcPhO:P3HT micro-structures with nano-porous surface morphology have been formed. • Multidimensional structures have been formed by electro-spraying technique. • The electro-sprayed films are very promising for the humidity sensors. - Abstract: In this paper, composite micro-structures of Vanadyl 2,9,16,23-tetraphenoxy-29H,31H-phthalocyanine) (VOPcPhO) and Poly (3-hexylthiophene-2,5-diyl) (P3HT) complex with nano-porous surface morphology have been developed by electro-spraying technique. The structural and morphological characteristics of the VOPcPhO:P3HT composite films have been studied by field emission scanning electron microscopy (FESEM) and atomic force microscopy (AFM). The multidimensional VOPcPhO:P3HT micro-structures formed by electro-spraying with nano-porous surface morphology are very promising for the humidity sensors due to the pore sizes in the range of micro to nano-meters scale. The performance of the VOPcPhO:P3HT electro-sprayed sensor is superior in term of sensitivity, hysteresis and response/recovery times as compared to the spin-coated one. The electro-sprayed humidity sensor exhibits ∼3 times and 0.19 times lower hysteresis in capacitive and resistive mode, respectively, as compared to the spin-coated humidity sensor.

  9. Otolith morphology and hearing abilities in cave- and surface-dwelling ecotypes of the Atlantic molly, Poecilia mexicana (Teleostei: Poeciliidae)

    Science.gov (United States)

    Schulz-Mirbach, Tanja; Ladich, Friedrich; Riesch, Rüdiger; Plath, Martin

    2010-01-01

    Cave fish have rarely been investigated with regard to their inner ear morphology, hearing abilities, and acoustic communication. Based on a previous study that revealed morphological differences in the saccular otolith between a cave and two surface populations of Poecilia mexicana, we checked for additional differences in utricular and lagenar otoliths and tested whether different populations have similar hearing sensitivities. We found pronounced differences in the shape of all three otoliths. Otoliths of the saccule and lagena from cave fish differed from those of surface fish in the features of the face oriented towards the sensory epithelium. In addition, otoliths of the utricle and lagena were significantly heavier in cave fish. Auditory sensitivities were measured between 100 and 1500 Hz, utilizing the auditory evoked potential recording technique. We found similar hearing abilities in cave and surface fish, with greatest sensitivity between 200 and 300 Hz. An acoustic survey revealed that neither ecotype produced species-specific sounds. Our data indicate that cave dwelling altered the otolith morphology in Atlantic mollies, probably due to metabolic differences. Different otolith morphology, however, did not affect general auditory sensitivity or acoustic behavior. PMID:20430090

  10. Dynamic Morphological Changes Induced By GM1 and Protein Interactions on the Surface of Cell-Sized Liposomes

    Directory of Open Access Journals (Sweden)

    Masahiro Takagi

    2013-06-01

    Full Text Available It is important to understand the physicochemical mechanisms that are responsible for the morphological changes in the cell membrane in the presence of various stimuli such as osmotic pressure. Lipid rafts are believed to play a crucial role in various cellular processes. It is well established that Ctb (Cholera toxin B subunit recognizes and binds to GM1 (monosialotetrahexosylganglioside on the cell surface with high specificity and affinity. Taking advantage of Ctb-GM1 interaction, we examined how Ctb and GM1 molecules affect the dynamic movement of liposomes. GM1 a natural ligand for cholera toxin, was incorporated into liposome and the interaction between fluorescent Ctb and the liposome was analyzed. The interaction plays an important role in determining the various surface interaction phenomena. Incorporation of GM1 into membrane leads to an increase of the line tension leading to either rupture of liposome membrane or change in the morphology of the membrane. This change in morphology was found to be GM1 concentration specific. The interaction between Ctb-GM1 leads to fast and easy rupture or to morphological changes of the liposome. The interactions of Ctb and the glycosyl chain are believed to affect the surface and the curvature of the membrane. Thus, the results are highly beneficial in the study of signal transduction processes.

  11. Study Of Morphological Changes Of Uterine Horn Of Surri Mouse Depended To Morphine Before Puberty And DuringPuberty

    Directory of Open Access Journals (Sweden)

    Shadkhast M

    2003-11-01

    Full Text Available : Morphine is the most important alkaloid of opium family which is found as much as ten percent in opium, and is in two types the sulfate morphine and the hydrochloride morphine."nMaterials and Methods: In this study morphological changes of uterus of surri mice due to oral consumption of sulfate morphine were studied. It was shown that, female surri mice following gradually increasing of morphine to water (0.1 and 0.01 mg/ml were depended to morphine. Female surri mice were classified in two age groups before puberty and depended to morphine during puberty. Each age group took morphine for 21 days. After finishing the period, the mice anesthetizing were weighted, then were anesthetizing and uterus was studied the length, width and apparent features."nResults&ConcIusion: In this study it was distinguished that length and width of uterine horn, between experimental and control groups, were significant (P< 0.01. Morphological changes such as anemia, the thinness and fragitidily walls of uterus and filiformity of uterine horns were observed."n"n"n"n"n"n 

  12. Effect of Deposition Rate on Structure and Surface Morphology of Thin Evaporated Al Films on Dielectrics and Semiconductors

    DEFF Research Database (Denmark)

    Bordo, K.; Rubahn, H. G.

    2012-01-01

    . The structure and surface morphology of the as-deposited Al films were studied using scanning electron microscopy (SEM) and atomic force microscopy (AFM). SEM imaging of the films showed that the mean grain size of thin Al films on all of the substrates increased from 20 nm - 30 nm to 50 nm - 70 nm...... with increase of the deposition rate. Quantitative AFM characterization showed that for all substrates the root mean square surface roughness increases monotonically with increasing the deposition rate from 0.1 nm/s to 2 nm/s. The observed effects of the deposition rate on the grain size and surface roughness...

  13. Crystallographic Textures and Morphologies of Solution Cast Ibuprofen Composite Films at Solid Surfaces

    Science.gov (United States)

    2014-01-01

    The preparation of thin composite layers has promising advantages in a variety of applications like transdermal, buccal, or sublingual patches. Within this model study the impact of the matrix material on the film forming properties of ibuprofen–matrix composite films is investigated. As matrix materials polystyrene, methyl cellulose, or hydroxyl-ethyl cellulose were used. The film properties were either varied by the preparation route, i.e., spin coating or drop casting, or via changes in the relative ratio of the ibuprofen and the matrix material. The resulting films were investigated via X-ray diffraction and atomic force microscope experiments. The results show that preferred (100) textures can be induced via spin coating with respect to the glass surface, while the drop casting results in a powder-like behavior. The morphologies of the films are strongly impacted by the ibuprofen amount rather than the preparation method. A comparison of the various matrix materials in terms of their impact on the dissolution properties show a two times faster zero order release from methyl cellulose matrix compared to a polystyrene matrix. The slowest rate was observed within the hydroxyl ethyl cellulose as the active pharmaceutical ingredients (APIs) release is limited by diffusion through a swollen matrix. The investigation reveals that the ibuprofen crystallization and film formation is only little effected by the selected matrix material than that compared to the dissolution. A similar experimental approach using other matrix materials may therefore allow to find an optimized composite layer useful for a defined application. PMID:25275801

  14. Size-dependent surface plasmon resonance in silver silica nanocomposites

    International Nuclear Information System (INIS)

    Thomas, Senoy; Nair, Saritha K; Jamal, E Muhammad Abdul; Anantharaman, M R; Al-Harthi, S H; Varma, Manoj Raama

    2008-01-01

    Silver silica nanocomposites were obtained by the sol-gel technique using tetraethyl orthosilicate (TEOS) and silver nitrate (AgNO 3 ) as precursors. The silver nitrate concentration was varied for obtaining composites with different nanoparticle sizes. The structural and microstructural properties were determined by x-ray diffractometry (XRD), Fourier transform infrared spectroscopy (FTIR) and transmission electron microscopy (TEM). X-ray photoelectron spectroscopic (XPS) studies were done for determining the chemical states of silver in the silica matrix. For the lowest AgNO 3 concentration, monodispersed and spherical Ag crystallites, with an average diameter of 5 nm, were obtained. Grain growth and an increase in size distribution was observed for higher concentrations. The occurrence of surface plasmon resonance (SPR) bands and their evolution in the size range 5-10 nm is studied. For decreasing nanoparticle size, a redshift and broadening of the plasmon-related absorption peak was observed. The observed redshift and broadening of the SPR band was explained using modified Mie scattering theory

  15. Investigating the time-dependent zeta potential of wood surfaces.

    Science.gov (United States)

    Muff, Livius F; Luxbacher, Thomas; Burgert, Ingo; Michen, Benjamin

    2018-05-15

    This work reports on streaming potential measurements through natural capillaries in wood and investigates the cause of a time-dependent zeta potential measured during the equilibration of wood cell-walls with an electrolyte solution. For the biomaterial, this equilibration phase takes several hours, which is much longer than for many other materials that have been characterized by electrokinetic measurements. During this equilibration phase the zeta potential magnitude is decaying due to two parallel mechanisms: (i) the swelling of the cell-wall which causes a dimensional change reducing the charge density at the capillary interface; (ii) the transport of ions from the electrolyte solution into the permeable cell-wall which alters the electrical potential at the interface by internal charge compensation. The obtained results demonstrate the importance of equilibration kinetics for an accurate determination of the zeta potential, especially for materials that interact strongly with the measurement electrolyte. Moreover, the change in zeta potential with time can be correlated with the bulk swelling of wood if the effect of electrolyte ion diffusion is excluded. This study shows the potential of streaming potential measurements of wood, and possibly of other hygroscopic and nanoporous materials, to reveal kinetic information about their interaction with liquids, such as swelling and ion uptake. Copyright © 2018 Elsevier Inc. All rights reserved.

  16. Influence of residual stress on the adhesion and surface morphology of PECVD-coated polypropylene

    Science.gov (United States)

    Jaritz, Montgomery; Hopmann, Christian; Behm, Henrik; Kirchheim, Dennis; Wilski, Stefan; Grochla, Dario; Banko, Lars; Ludwig, Alfred; Böke, Marc; Winter, Jörg; Bahre, Hendrik; Dahlmann, Rainer

    2017-11-01

    The properties of plasma-enhanced chemical vapour deposition (PECVD) coatings on polymer materials depend to some extent on the surface and material properties of the substrate. Here, isotactic polypropylene (PP) substrates are coated with silicon oxide (SiO x ) films. Plasmas for the deposition of SiO x are energetic and oxidative due to the high amount of oxygen in the gas mixture. Residual stress measurements using single Si cantilever stress sensors showed that these coatings contain high compressive stress. To investigate the influence of the plasma and the coatings, residual stress, silicon organic (SiOCH) coatings with different thicknesses between the PP and the SiO x coating are used as a means to protect the substrate from the oxidative SiO x coating process. Pull-off tests are performed to analyse differences in the adhesion of these coating systems. It could be shown that the adhesion of the PECVD coatings on PP depends on the coatings’ residual stress. In a PP/SiOCH/SiO x -multilayer system the residual stress can be significantly reduced by increasing the thickness of the SiOCH coating, resulting in enhanced adhesion.

  17. Surface morphology and dewettability of self-organized thermosets involving epoxy and POSS-capped poly(ethylene oxide) telechelics

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Lei [Department of Polymer Science and Engineering and the State Key Laboratory of Metal Matrix Composites, Shanghai Jiao Tong University, Shanghai 200240 (China); Zheng, Sixun, E-mail: szheng@sjtu.edu.cn [Department of Polymer Science and Engineering and the State Key Laboratory of Metal Matrix Composites, Shanghai Jiao Tong University, Shanghai 200240 (China)

    2012-10-15

    A heptaphenyl polyhedral oligomeric silsesquioxane-capped poly(ethylene oxide) (POSS-capped PEO) telechelics was synthesized via the Huisgen 1,3-dipolar cycloaddition between 3-azidopropylheptaphenyl POSS and {alpha},{omega}-dialkynyl-terminated poly(ethylene oxide). The organic-inorganic amphiphile was incorporated into epoxy to obtain the organic-inorganic nanocomposites. The morphology of the nanocomposites was investigated by means of atomic force microscopy (AFM) and dynamic mechanical thermal analysis (DMTA). It was found that the epoxy thermosets containing POSS-capped PEO telechelics were microphase-separated. The formation of the nanophases in the thermosets followed a self-assembly mechanism. The static contact angle measurements show that the nanocomposites displayed a significant enhancement in surface hydrophobicity as well as reduction in surface free energy. The improvement in surface dewettability was ascribed to the enrichment of POSS cages at the surface of the nanocomposites and the formation of the specific surface morphology as evidenced by X-ray photoelectron spectroscopy (XPS) and surface atomic force microscopy (AFM). -- Highlights: Black-Right-Pointing-Pointer POSS-capped PEO telechelics was synthesized via click chemistry approach. Black-Right-Pointing-Pointer The organic-inorganic amphiphile can be self-assembled into the nanophases in epoxy. Black-Right-Pointing-Pointer The hybrid nanocomposites were successfully prepared via a self-assembly approach. Black-Right-Pointing-Pointer The nanocomposites displayed a significant enhancement in surface hydrophobicity.

  18. Surface morphology and dewettability of self-organized thermosets involving epoxy and POSS-capped poly(ethylene oxide) telechelics

    International Nuclear Information System (INIS)

    Wang, Lei; Zheng, Sixun

    2012-01-01

    A heptaphenyl polyhedral oligomeric silsesquioxane-capped poly(ethylene oxide) (POSS-capped PEO) telechelics was synthesized via the Huisgen 1,3-dipolar cycloaddition between 3-azidopropylheptaphenyl POSS and α,ω-dialkynyl-terminated poly(ethylene oxide). The organic–inorganic amphiphile was incorporated into epoxy to obtain the organic–inorganic nanocomposites. The morphology of the nanocomposites was investigated by means of atomic force microscopy (AFM) and dynamic mechanical thermal analysis (DMTA). It was found that the epoxy thermosets containing POSS-capped PEO telechelics were microphase-separated. The formation of the nanophases in the thermosets followed a self-assembly mechanism. The static contact angle measurements show that the nanocomposites displayed a significant enhancement in surface hydrophobicity as well as reduction in surface free energy. The improvement in surface dewettability was ascribed to the enrichment of POSS cages at the surface of the nanocomposites and the formation of the specific surface morphology as evidenced by X-ray photoelectron spectroscopy (XPS) and surface atomic force microscopy (AFM). -- Highlights: ► POSS-capped PEO telechelics was synthesized via click chemistry approach. ► The organic–inorganic amphiphile can be self-assembled into the nanophases in epoxy. ► The hybrid nanocomposites were successfully prepared via a self-assembly approach. ► The nanocomposites displayed a significant enhancement in surface hydrophobicity.

  19. The effect of amorphous silicon surface hydrogenation on morphology, wettability and its implication on the adsorption of proteins

    International Nuclear Information System (INIS)

    Filali, Larbi; Brahmi, Yamina; Sib, Jamal Dine; Bouhekka, Ahmed; Benlakehal, Djamel; Bouizem, Yahya; Kebab, Aissa; Chahed, Larbi

    2016-01-01

    Highlights: • Hydrogenation of the surfaces had the effect of reducing the roughness by way of shadow etching. • Roughness was the driving factor affecting the wettability of the hydrogenated surfaces. • Bovine Serum Albumin proteins favored the surfaces with highest hydrogen content. • Surface modification induced secondary structure change of adsorbed proteins. - Abstract: We study the effect of amorphous silicon (a-Si) surface hydrogenation on Bovine Serum Albumin (BSA) adsorption. A set of (a-Si) films was prepared by radio frequency magnetron sputtering (RFMS) and after deposition; they were treated in molecular hydrogen ambient at different pressures (1–3 Pa). Fourier transform infrared attenuated total reflection (FTIR-ATR) spectroscopy and spectroscopic ellipsometry (SE) were used to study the hydrogenation effect and BSA adsorption. Atomic force microscopy (AFM) was used to evaluate morphological changes caused by hydrogenation. The wettability of the films was measured using contact angle measurement, and in the case of the hydrogenated surfaces, it was found to be driven by surface roughness. FTIR-ATR spectroscopy and SE measurements show that proteins had the strongest affinity toward the surfaces with the highest hydrogen content and their secondary structure was affected by a significant decrease of the α-helix component (-27%) compared with the proteins adsorbed on the un-treated surface, which had a predominantly α-helix (45%) structure. The adsorbed protein layer was found to be densely packed with a large thickness (30.9 nm) on the hydrogen-rich surfaces. The most important result is that the surface hydrogen content was the dominant factor, compared to wettability and morphology, for protein adsorption.

  20. The effect of amorphous silicon surface hydrogenation on morphology, wettability and its implication on the adsorption of proteins

    Energy Technology Data Exchange (ETDEWEB)

    Filali, Larbi, E-mail: larbifilali5@gmail.com [Laboratoire de Physique des Couches Minces et Matériaux pour l' Electronique, Université d' Oran 1, Ahmed Ben Bella, BP 1524, El M' naouar 31100 Oran (Algeria); Brahmi, Yamina; Sib, Jamal Dine [Laboratoire de Physique des Couches Minces et Matériaux pour l' Electronique, Université d' Oran 1, Ahmed Ben Bella, BP 1524, El M' naouar 31100 Oran (Algeria); Bouhekka, Ahmed [Laboratoire de Physique des Couches Minces et Matériaux pour l' Electronique, Université d' Oran 1, Ahmed Ben Bella, BP 1524, El M' naouar 31100 Oran (Algeria); Département de Physique, Université Hassiba Ben Bouali, 02000 Chlef (Algeria); Benlakehal, Djamel; Bouizem, Yahya; Kebab, Aissa; Chahed, Larbi [Laboratoire de Physique des Couches Minces et Matériaux pour l' Electronique, Université d' Oran 1, Ahmed Ben Bella, BP 1524, El M' naouar 31100 Oran (Algeria)

    2016-10-30

    Highlights: • Hydrogenation of the surfaces had the effect of reducing the roughness by way of shadow etching. • Roughness was the driving factor affecting the wettability of the hydrogenated surfaces. • Bovine Serum Albumin proteins favored the surfaces with highest hydrogen content. • Surface modification induced secondary structure change of adsorbed proteins. - Abstract: We study the effect of amorphous silicon (a-Si) surface hydrogenation on Bovine Serum Albumin (BSA) adsorption. A set of (a-Si) films was prepared by radio frequency magnetron sputtering (RFMS) and after deposition; they were treated in molecular hydrogen ambient at different pressures (1–3 Pa). Fourier transform infrared attenuated total reflection (FTIR-ATR) spectroscopy and spectroscopic ellipsometry (SE) were used to study the hydrogenation effect and BSA adsorption. Atomic force microscopy (AFM) was used to evaluate morphological changes caused by hydrogenation. The wettability of the films was measured using contact angle measurement, and in the case of the hydrogenated surfaces, it was found to be driven by surface roughness. FTIR-ATR spectroscopy and SE measurements show that proteins had the strongest affinity toward the surfaces with the highest hydrogen content and their secondary structure was affected by a significant decrease of the α-helix component (-27%) compared with the proteins adsorbed on the un-treated surface, which had a predominantly α-helix (45%) structure. The adsorbed protein layer was found to be densely packed with a large thickness (30.9 nm) on the hydrogen-rich surfaces. The most important result is that the surface hydrogen content was the dominant factor, compared to wettability and morphology, for protein adsorption.

  1. Morphological development of surface scales during long term oxidation of a low Al-substituted β'-sialon

    International Nuclear Information System (INIS)

    Pomeroy, M.J.; Ramesh, R.; Hampshire, S.

    1994-01-01

    The morphological development of oxide scales formed on a low Al substituted β-sialon (z=0.2) oxidised for time periods up to 1024h at 1350 C is discussed in relation to oxidation kinetics. The oxidation process is observed to be accompanied by changes in both the phase assemblage of the external layers and their morphology. Thus as the time of oxidation increases beyond 64h the cristobalite-β-yttrium disilicate phase assemblage changes to cristobalite plus β- and γ-yttrium disilicate. In addition to the changes observed for the surface layers, differences are observed in the morphologies of the polished cross-sections. These changes are consistent with an order of magnitude decrease in oxidation rate. (orig.)

  2. The effect of the NMDA receptor-dependent signaling pathway on cell morphology and melanosome transfer in melanocytes.

    Science.gov (United States)

    Ni, Jing; Wang, Nan; Gao, Lili; Li, Lili; Zheng, Siwen; Liu, Yuejian; Ozukum, Molu; Nikiforova, Anna; Zhao, Guangming; Song, Zhiqi

    2016-12-01

    The pigmentation of skin and hair in mammals is driven by the intercellular transfer of melanosome from the melanocyte to surrounding keratinocytes However, the detailed molecular mechanism is still a subject of investigation. To investigate the effects of N-methyl-d-aspartate (NMDA) receptor-dependent signaling pathway on melanocyte morphologic change and melanosome transfer between melanocytes and keratinocytes. The expression and the intracellular distribution of NMDA receptor in human melanocyte were analyzed by Western blot and immunofluorescence staining. Melanocytes were treated with 100μM NMDA receptor antagonist MK-801 [(+)-5-methyl-10,11-dihydro-5H-dibenzo[a,d] cyclohepten-5,10-imine maleate] and 100μM NMDA receptor agonist NMDA, after which the morphological change of melanocyte dendrites and filopodias were observed by scanning electron microscope. The β-tubulin distribution and intracellular calcium concentration ([Ca 2+ ] i ) were observed by immunofluorescence staining and flow cytometry under the same treatment respectively. In addition, melanocytes and keratinocytes were co-cultured with or without treatment of MK-801, and the melanosome transfer efficacy were analyzed by flow cytometry. We show that human epidermal melanocytes expresses NMDA receptor 1, one subtype of the ionotropic glutamate receptors (iGluRs). Stimulation with agonist of NMDA receptor increased the number of melanocyte filopodia. In contrast, blockage of NMDA receptor with antagonist decreased the number of melanocyte filopodia and this morphological change was accompanied by the disorganization of β-tubulin microfilaments in the intracellular cytoskeleton. In melanocyte-keratinocyte co-cultures, numerous melanocyte filopodia connect to keratinocyte plasma membranes; agonist of NMDA receptor exhibited an increased number of melanocyte filopodia attachments to keratinocyte, while antagonist of NMDA receptor led to a decreased. Moreover, antagonist of NMDA receptor decreased

  3. In situ regulating of surface morphologies, anti-corrosion and tribological properties of epoxy resin coatings by heat treatment

    Science.gov (United States)

    Liu, Dan; Zhao, Wenjie; Liu, Shuan; Cen, Qihong; Xue, Qunji

    2017-06-01

    A simple and in situ formation method through controlling curing temperature was used to regulate the surface morphology of epoxy resin (EP) coating. Multi-functional tribology test equipment and an electrochemistry workstation were used to evaluate the tribological and anti-corrosion properties of the EP coating cured with diethylenetriamine at room temperature, 80 °C, 100 °C and 120 °C, respectively. The results indicated that the diameter and depth of pores or pits existing on the surface of EP coatings decreased significantly with the increase of curing temperature. The EP coating cured at 120 °C exhibited the best tribological performance, the friction coefficient and wear trace area were 0.56 and 0.003 02 mm2 under dry conditions, 0.18 and 1.873  ×  10-5 mm2 under seawater conditions, respectively. The excellent tribological performance could be attributed to the surface morphologies and high hardness of EP coatings. The EP coating cured at 80 °C exhibited the best anti-corrosion performance that the impedance modulus at 0.01 Hz was close to 5.0 KΩ cm2 even after being immersed in 3.5 wt% NaCl solution for 24 h, which was closely related to its hydrophobic behavior and surface morphology.

  4. A dynamic monitoring approach for the surface morphology evolution measurement of plasma facing components by means of speckle interferometry

    Science.gov (United States)

    Wang, Hongbei; Cui, Xiaoqian; Feng, Chunlei; Li, Yuanbo; Zhao, Mengge; Luo, Guangnan; Ding, Hongbin

    2017-11-01

    Plasma Facing Components (PFCs) in a magnetically confined fusion plasma device will be exposed to high heat load and particle fluxes, and it would cause PFCs' surface morphology to change due to material erosion and redeposition from plasma wall interactions. The state of PFCs' surface condition will seriously affect the performance of long-pulse or steady state plasma discharge in a tokamak; it will even constitute an enormous threat to the operation and the safety of fusion plasma devices. The PFCs' surface morphology evolution measurement could provide important information about PFCs' real-time status or damage situation and it would help to a better understanding of the plasma wall interaction process and mechanism. Meanwhile through monitoring the distribution of dust deposition in a tokamak and providing an upper limit on the amount of loose dust, the PFCs' surface morphology measurement could indirectly contribute to keep fusion operational limits and fusion device safety. Aiming at in situ dynamic monitoring PFCs' surface morphology evolution, a laboratory experimental platform DUT-SIEP (Dalian University of Technology-speckle interferometry experimental platform) based on the speckle interferometry technique has been constructed at Dalian University of Technology (DUT) in China. With directional specific designing and focusing on the real detection condition of EAST (Experimental Advanced Superconducting Tokamak), the DUT-SIEP could realize a variable measurement range, widely increased from 0.1 μm to 300 μm, with high spatial resolution (adopted from EAST has been measured, and the feasibility and reliability of this new experimental platform have been demonstrated.

  5. Effects of Surface Morphology ZnAl2O4 of Ceramic Materials on Osteoblastic Cells Responses

    International Nuclear Information System (INIS)

    Suarez-Franco, J.L.; Fernandez-Pedrero, J.A.; Ivarez-Perez, M.A.; Garcia-Hipolito, M.; Surarez-Rosales, M.; Fregoso, O.; Juarez-Islas, J.A.; Ivarez-Perez, M.A.

    2013-01-01

    Ceramic scaffolds are widely studied in the tissue engineering field due to their potential in medical applications as bone substitutes or as bone-filling materials. The purpose of this study was to investigate the effect of surface morphology of nano structure thin films of ZnAl 2 O 4 prepared by spray pyrolysis and bulk pellets of polycrystalline ZnAl 2 O 4 prepared by chemical coprecipitation reaction on the in vitro cell adhesion, viability, and cell-material interactions of osteoblastic cells. Our result showed that cell attachment was significantly enhanced from 60 to 80% on the ZnAl 2 O 4 nano structured material surface when compared with bulk ceramic surfaces. Moreover, our results showed that the balance of morphological properties of the thin film nano structure ceramic improves cell-material interaction with enhanced spreading and filopodia with multiple cellular extensions on the surface of the ceramic and enhancing cell viability/proliferation in comparison with bulk ceramic surfaces used as control. Altogether, these results suggest that zinc aluminate nano structured materials have a great potential to be used in dental implant and bone substitute applications.Ceramic scaffolds are widely studied in the tissue engineering field due to their potential in medical applications as bone substitutes or as bone-filling materials. The purpose of this study was to investigate the effect of surface morphology of nano structure thin films of ZnAl 2 O 4 prepared by spray pyrolysis and bulk pellets of polycrystalline ZnAl 2 O 4 prepared by chemical coprecipitation reaction on the in vitro cell adhesion, viability, and cell-material interactions of osteoblastic cells. Our result showed that cell attachment was significantly enhanced from 60 to 80% on the ZnAl 2 O 4 nano structured material surface when compared with bulk ceramic surfaces. Moreover, our results showed that the balance of morphological properties of the thin film nano structure ceramic improves

  6. Growth Mechanism of Strain-Dependent Morphological Change in PEDOT:PSS Films.

    Science.gov (United States)

    Lee, Yoo-Yong; Choi, Gwang Mook; Lim, Seung-Min; Cho, Ju-Young; Choi, In-Suk; Nam, Ki Tae; Joo, Young-Chang

    2016-04-29

    Understanding the mechanism of the strain-dependent conductivity change in polymers in stretched conditions is important. We observed a strain-induced growth of the conductive regions of PSS films, induced by a coalescence of conductive PEDOT-rich cores. This growth due to coalescence leads to a gradual decrease in the electrical resistivity up to 95%, independent of the thickness of the PSS films. The primary mechanism for the evolution of the PEDOT-rich cores proceeds by the cores growing larger as they consuming relatively smaller cores. This process is caused by a strain-induced local rearrangement of PEDOT segments in the vicinity of PSS shells around the cores and also changes the chemical environment in PEDOT, induced by the electron-withdrawing effects around the PEDOT chains. The strain-induced growth mechanism is beneficial to understanding the phenomenon of polymeric chain rearrangement in mechanical deformation and to modulating the electrical conductivity for practical applications.

  7. Surface morphology of caldera-forming eruption deposits revealed by lidar mapping of Crater Lake National Park, Oregon - Implications for deposition and surface modification

    Science.gov (United States)

    Robinson, Joel E.; Bacon, Charles R.; Major, Jon J.; Wright, Heather M.; Vallance, James W.

    2017-08-01

    Large explosive eruptions of silicic magma can produce widespread pumice fall, extensive ignimbrite sheets, and collapse calderas. The surfaces of voluminous ignimbrites are rarely preserved or documented because most terrestrial examples are heavily vegetated, or severely modified by post-depositional processes. Much research addresses the internal sedimentary characteristics, flow processes, and depositional mechanisms of ignimbrites, however, surface features of ignimbrites are less well documented and understood, except for comparatively small-volume deposits of historical eruptions. The 7700 calendar year B.P. climactic eruption of Mount Manama, USA, vented 50 km3 of magma, deposited first as rhyodacite pumice fall and then as a zoned rhyodacite-to-andesite ignimbrite as Crater Lake caldera collapsed. Lidar collected during summer 2010 reveals the remarkably well-preserved surface of the Manama ignimbrite and related deposits surrounding Crater Lake caldera in unprecedented detail despite forest cover. The ± 1 m lateral and ± 4 cm vertical resolution lidar allows surface morphologies to be classified. Surface morphologies are created by internal depositional processes and can point to the processes at work when pyroclastic flows come to rest. We describe nine surface features including furrow-ridge sets and wedge-shaped mounds in pumice fall eroded by high-energy pyroclastic surges, flow-parallel ridges that record the passage of multiple pyroclastic flows, perched benches of marginal deposits stranded by more-mobile pyroclastic-flow cores, hummocks of dense clasts interpreted as lag deposit, transverse ridges that mark the compression and imbrication of flows as they came to rest, scarps indicating ignimbrite remobilization, fields of closely spaced pits caused by phreatic explosions, fractures and cracks due to extensional processes resulting from ignimbrite volume loss, and stream channels eroded in the newly formed surface. The nine morphologies

  8. Reversible and irreversible changes of surface morphology by order-disorder transition in CuAu alloy

    Energy Technology Data Exchange (ETDEWEB)

    Sachl, Jindrich; Sima, Vladimir; Pfeiler, Wolfgang

    2004-09-22

    The change of symmetry from the disordered fcc structure to tetragonal or orthorhombic structure is accompanied in CuAu alloy by anisotropy of lattice parameters and also by local generation of c-variants of structural antiphase domains. Macroscopic results of these processes can be observed as a dynamic change of the surface morphology. Some surface changes are reversible, on the other hand the internal stresses connected with the order-disorder transformation are also responsible for irreversible surface deformation effects. The domain structure formation can be influenced by external load and a shape memory effect can be observed at special conditions in CuAu. A combination of in-situ microscopic video cinematography and post-mortem 3-D atomic force microscopy (AFM) has been used for the surface study. The AFM images have enabled a detailed analysis of the surface morphology and the cinematography has given an in-situ information dealing with conditions and kinetics of observed surface changes. Measurements on CuAu single- and poly-crystalline samples have been made for a wide variety of experimental conditions (heating/cooling rates, external load, thermal history of the sample)

  9. Reversible and irreversible changes of surface morphology by order-disorder transition in CuAu alloy

    International Nuclear Information System (INIS)

    Sachl, Jindrich; Sima, Vladimir; Pfeiler, Wolfgang

    2004-01-01

    The change of symmetry from the disordered fcc structure to tetragonal or orthorhombic structure is accompanied in CuAu alloy by anisotropy of lattice parameters and also by local generation of c-variants of structural antiphase domains. Macroscopic results of these processes can be observed as a dynamic change of the surface morphology. Some surface changes are reversible, on the other hand the internal stresses connected with the order-disorder transformation are also responsible for irreversible surface deformation effects. The domain structure formation can be influenced by external load and a shape memory effect can be observed at special conditions in CuAu. A combination of in-situ microscopic video cinematography and post-mortem 3-D atomic force microscopy (AFM) has been used for the surface study. The AFM images have enabled a detailed analysis of the surface morphology and the cinematography has given an in-situ information dealing with conditions and kinetics of observed surface changes. Measurements on CuAu single- and poly-crystalline samples have been made for a wide variety of experimental conditions (heating/cooling rates, external load, thermal history of the sample)

  10. Surface adhesion and its dependence on surface roughness and humidity measured with a flat AFM tip

    NARCIS (Netherlands)

    Colak, A.; Wormeester, Herbert; Zandvliet, Henricus J.W.; Poelsema, Bene

    2012-01-01

    The adhesion force between a surface and the tip of an atomic force microscope cantilever has been determined by recording force–distance curves with an atomic force microscope. Flat tips with a diameter of 2 μm were used to mimic the adhesion between two parallel surfaces. In such a configuration,

  11. CANDELS OBSERVATIONS OF THE ENVIRONMENTAL DEPENDENCE OF THE COLOR-MASS-MORPHOLOGY RELATION AT z = 1.6

    Energy Technology Data Exchange (ETDEWEB)

    Bassett, Robert; Papovich, Casey; Tran, Kim-Vy [George P. and Cynthia Woods Mitchell Institute for Fundamental Physics and Astronomy, College Station, TX 77843-4242 (United States); Lotz, Jennifer M.; Ferguson, Henry C.; Koekemoer, Anton M. [Space Telescope Science Institute, 3700 San Martin Dr., Baltimore, MD 21218 (United States); Bell, Eric F. [Department of Astronomy, University of Michigan, Ann Arbor, MI 48109 (United States); Finkelstein, Steven L. [Department of Astronomy, University of Texas, Austin, TX 78712 (United States); Newman, Jeffrey A. [Department of Physics and Astronomy, University of Pittsburgh, Pittsburgh, PA 15260 (United States); Almaini, Omar; Lani, Caterina [School of Physics and Astronomy, University of Nottingham, Nottingham (United Kingdom); Cooper, Michael [Center for Galaxy Evolution, Department of Physics and Astronomy, University of California, Irvine, 4129 Frederick Reines Hall, Irvine, CA 92697 (United States); Croton, Darren [Centre for Astrophysics and Supercomputing, Swinburne University of Technology, Hawthorn (Australia); Dekel, Avishai [Racah Institute of Physics, The Hebrew University, Jerusalem 91904 (Israel); Kocevski, Dale D.; Koo, David C.; McGrath, Elizabeth J. [UCO/Lick Observatory, Department of Astronomy and Astrophysics, University of California, Santa Cruz, CA 95064 (United States); McIntosh, Daniel H. [Department of Physics, University of Missouri-Kansas City, 5110 Rockhill Road, Kansas City, MO 64110 (United States); Wechsler, Risa [Kavli Institute for Particle Astrophysics and Cosmology, Physics Department, and SLAC National Accelerator Laboratory, Stanford University, Stanford, CA 94305 (United States)

    2013-06-10

    We study the environmental dependence of color, stellar mass, and morphology by comparing galaxies in a forming cluster to those in the field at z = 1.6 with Hubble Space Telescope near-infrared imaging in the CANDELS/UDS field. We quantify the morphology of the galaxies using the effective radius, r{sub eff}, and Sersic index, n. In both the cluster and field, approximately half of the bulge-dominated galaxies (n > 2) reside on the red sequence of the color-magnitude diagram, and most disk-dominated galaxies (n < 2) have colors expected for star-forming galaxies. There is weak evidence that cluster galaxies have redder rest-frame U - B colors and higher stellar masses compared to the field. Star-forming galaxies in both the cluster and field show no significant differences in their morphologies. In contrast, there is evidence that quiescent galaxies in the cluster have larger median effective radii and smaller Sersic indices compared to the field with a significance of 2{sigma}. These differences are most pronounced for galaxies at clustercentric distances 1 Mpc

  12. In-Vitro Comparative Study of In-office and Home Bleaching Agents on Surface Micro-morphology of Enamel

    International Nuclear Information System (INIS)

    Fatima, N.

    2016-01-01

    Objective: To evaluate the effect of home-use bleaching agent containing 16 percent Carbamide Peroxide (CP) and in-office bleaching agent with 38 percentage Hydrogen Peroxide (HP) on surface micro-morphology of enamel. Study Design: An experimental study. Place and Duration of Study: The discs were prepared at Material Engineering Department of NED University of Engineering and Technology, Karachi, and surface morphology was analyzed at Centralized Science Laboratory of Karachi University, Pakistan. Duration of study was one year from January to December 2012. Methodology: Forty five sound human third molar crowns, extracted for periodontal reason, were included in the study. Longitudinal sections were made using diamond disks (0.2 mm) under water lubrication to obtain enamel slabs measuring (3 mm x 3 mm). The slabs were embedded in polystyrene resin by using 2.0 cm diameter PVC molds, leaving the outer enamel surface uncovered by the resin. Ninety dental enamel slabs were prepared. The slabs were then randomly divided into 3 groups. Each group contained thirty specimens (n=30). Group 1 was kept in artificial saliva at 37 degree C in incubator (Memart, Germany) during whole experiment. Group 2 was treated with power whitening gel (White Smile 2011, Germany). Group 3 was treated with tooth whitening pen (White Smile 2011, Germany). The most central region or the region that was most representative of the entire surface area was used. The SEM (Jeol-Japan-JSM6380A, JAPAN) micrographs were examined to determine the type of surface presented. The enamel changes were classified as no or mild alteration, moderate alteration and severe altered surface. Results: Regarding micro-morphology, the enamel surface of control groups showed smooth surface in general with some scattered clear scratches due to the polishing procedure. The specimens bleached in group 2 and group 3, represented areas of mild erosion. Conclusion: Bleaching with 38 percentage Hydrogen Peroxide (HP) and

  13. Morphology-dependent Electrochemical Enhancements of Porous Carbon as Sensitive Determination Platform for Ascorbic Acid, Dopamine and Uric Acid

    Science.gov (United States)

    Cheng, Qin; Ji, Liudi; Wu, Kangbing; Zhang, Weikang

    2016-02-01

    Using starch as the carbon precursor and different-sized ZnO naoparticles as the hard template, a series of porous carbon materials for electrochemical sensing were prepared. Experiments of scanning electron microscopy, transmission electron microscopy and Nitrogen adsorption-desorption isotherms reveal that the particle size of ZnO has big impacts on the porous morphology and surface area of the resulting carbon materials. Through ultrasonic dispersion of porous carbon and subsequent solvent evaporation, different sensing interfaces were constructed on the surface of glassy carbon electrode (GCE). The electrochemical behaviors of ascorbic acid (AA), dopamine (DA) and uric acid (UA) were studied. On the surface of porous carbon materials, the accumulation efficiency and electron transfer ability of AA, DA and UA are improved, and consequently their oxidation signals enhance greatly. Moreover, the interface enhancement effects of porous carbon are also controlled by the particle size of hard template. The constructed porous carbon interface displays strong signal amplification ability and holds great promise in constructing a sensitive platform for the simultaneous determination of AA, DA and UA.

  14. Growth Temperature Dependence of Morphology of GaN Single Crystals in the Na-Li-Ca Flux Method

    Science.gov (United States)

    Wu, Xi; Hao, Hangfei; Li, Zhenrong; Fan, Shiji; Xu, Zhuo

    2018-02-01

    In this paper, the effect of growth temperature on the morphology and transparency of the GaN crystals obtained by the Li-Ca-added Na Flux method was studied. Addition of Li-Ca was attempted to control the growth habit and further improve transparency of GaN crystals. The samples with wurtzite structure of GaN were confirmed by the x-ray powder diffraction analysis. GaN single crystal with maximum size of about 6 mm was grown at 750°C. As the growth temperature was increased from 700°C to 850°C, the morphology of the crystals changed from pyramid to prism, and their surfaces became smooth. It was found that high growth temperature was beneficial to obtain a transparent crystal, but the evaporation of sodium would suppress its further growth. The E 2 (high) mode in the Raman spectra was at 568 cm-1, and the full-width at half-maximum values of this peak for the crystals obtained at 700°C, 750°C, 800°C, and 850°C were 7.5 cm-1, 10.3 cm-1, 4.4 cm-1, and 4.0 cm-1, respectively. It indicates that all the crystals are stress free and the transparent crystal grown at high temperature has high structural quality or low impurity concentrations.

  15. Screen-printed carbon electrode modified on its surface with amorphous carbon nitride thin film: Electrochemical and morphological study

    Energy Technology Data Exchange (ETDEWEB)

    Ghamouss, F. [Universite de Nantes, UMR 6006-CNRS, FR-2465-CNRS, Laboratoire d' Analyse isotopique et Electrochimique de Metabolismes (LAIEM) (France); Tessier, P.-Y. [Universite de Nantes, UMR CNRS 6502, Institut des Materiaux Jean Rouxel - IMN Faculte des Sciences and des Techniques de Nantes, 2 rue de la Houssiniere, 44322 Nantes Cedex 3 (France); Djouadi, A. [Universite de Nantes, UMR CNRS 6502, Institut des Materiaux Jean Rouxel - IMN Faculte des Sciences and des Techniques de Nantes, 2 rue de la Houssiniere, 44322 Nantes Cedex 3 (France); Besland, M.-P. [Universite de Nantes, UMR CNRS 6502, Institut des Materiaux Jean Rouxel - IMN Faculte des Sciences and des Techniques de Nantes, 2 rue de la Houssiniere, 44322 Nantes Cedex 3 (France); Boujtita, M. [Universite de Nantes, UMR 6006-CNRS, FR-2465-CNRS, Laboratoire d' Analyse isotopique et Electrochimique de Metabolismes (LAIEM) (France)]. E-mail: mohammed.boujtita@univ-nantes.fr

    2007-04-20

    The surface of a screen-printed carbon electrode (SPCE) was modified by using amorphous carbon nitride (a-CN {sub x}) thin film deposited by reactive magnetron sputtering. Scanning electron microscopy and photoelectron spectroscopy measurements were used to characterise respectively the morphology and the chemical structure of the a-CN {sub x} modified electrodes. The incorporation of nitrogen in the amorphous carbon network was demonstrated by X ray photoelectron spectroscopy. The a-CN {sub x} layers were deposited on both carbon screen-printed electrode (SPCE) and silicon (Si) substrates. A comparative study showed that the nature of substrate, i.e. SPCE and Si, has a significant effect on both the surface morphology of deposited a-CN {sub x} film and their electrochemical properties. The improvement of the electrochemical reactivity of SPCE after a-CN {sub x} film deposition was highlighted both by comparing the shapes of voltammograms and calculating the apparent heterogeneous electron transfer rate constant.

  16. Mechanism of surface morphology in electron beam melting of Ti6Al4V based on computational flow patterns

    Science.gov (United States)

    Ge, Wenjun; Han, Sangwoo; Fang, Yuchao; Cheon, Jason; Na, Suck Joo

    2017-10-01

    In this study, a 3D numerical model was proposed that uses the computational fluid dynamics (CFD) method to investigate molten pool formation in electron beam melting under different process parameters. Electron beam ray tracking was used to determine energy deposition in the powder bed model. The melt tracks obtained in this study can be divided into three categories: a balling pattern, distortion pattern and straight pattern. The 3D mesoscale model revealed that it is possible to obtain different molten pool temperature distributions, flow patterns and top surface morphologies using different process parameters. Detailed analysis was performed on the formation mechanism of both the balling defect and distortion pattern. The simulation results of the top surface morphology were also compared with experimental results and showed good agreement.

  17. How surface roughness affects the angular dependence of the sputtering yield

    International Nuclear Information System (INIS)

    Hu, A.; Hassanein, A.

    2012-01-01

    Comprehensive model is developed to study the impact of surface roughness on the angular dependence of sputtering yield. Instead of assuming surfaces to be flat or composed of exact self-similar fractals, we developed a new method to describe the surfaces. Random fractal surfaces generated by midpoint displacement algorithm in computer graphics area and Support vector machine algorithm in pattern recognition area are combined with the Monte Carlo ion bombardment simulation code, i.e., Ion Transport in Materials and Compounds (ITMC) code . With this new fractal version of ITMC-F, we successfully simulated the angular dependence of sputtering yield for various ion-target combinations. Examples are given for 5 keV Ar ions bombarding iron, graphite, and silicon surfaces, with the input surface roughness exponent directly depicted from experimental data. Comparison is made with previous models to account for surface roughness and recent experimental data. The ITMC-F code showed good agreement with the experimental data.

  18. Pressure-dependent surface viscosity and its surprising consequences in interfacial lubrication flows

    Science.gov (United States)

    Manikantan, Harishankar; Squires, Todd M.

    2017-02-01

    The surface shear rheology of many insoluble surfactants depends strongly on the surface pressure (or concentration) of that surfactant. Here we highlight the dramatic consequences that surface-pressure-dependent surface viscosities have on interfacially dominant flows, by considering lubrication-style geometries within high Boussinesq (Bo) number flows. As with three-dimensional lubrication, high-Bo surfactant flows through thin gaps give high surface pressures, which in turn increase the local surface viscosity, further amplifying lubrication stresses and surface pressures. Despite their strong nonlinearity, the governing equations are separable, so that results from two-dimensional Newtonian lubrication analyses may be immediately adapted to treat surfactant monolayers with a general functional form of ηs(Π ) . Three paradigmatic systems are analyzed to reveal qualitatively new features: a maximum, self-limiting value for surfactant fluxes and particle migration velocities appears for Π -thickening surfactants, and kinematic reversibility is broken for the journal bearing and for suspensions more generally.

  19. Time dependency of morphological remodeling of endothelial cells in response to substrate stiffness

    Science.gov (United States)

    Goli-Malekabadi, Zahra; Tafazzoli-shadpour, Mohammad; Tamayol, Ali; Seyedjafari, Ehsan

    2017-01-01

    Introduction: Substrate stiffness regulates cellular behavior as cells experience different stiffness values of tissues in the body. For example, endothelial cells (ECs) covering the inner layer of blood vessels are exposed to different stiffness values due to various pathologic and physiologic conditions. Despite numerous studies, cells by time span sense mechanical properties of the substrate, but the response is not well understood. We hypothesized that time is a major determinant influencing the behavior of cells seeded on substrates of varying stiffness. Methods: We monitored cell spreading, internal structure, 3D topography, and the viability of ECs over 24 hours of culture on polydimethylsiloxane (PDMS) substrates with two different degrees of elastic modulus. Results: Despite significant differences in cell spreading after cell seeding, cells showed a similar shape and internal structure after 24 hours of culture on both soft and stiff substrates. However, 3D topographical images confirmed existence of rich lamellipodia and filopodia around the cells cultured on stiffer PDMS substrates. Conclusion: It was concluded that the response of ECs to the substrate stiffness was time dependent with initial enhanced cellular spreading and viability on stiffer substrates. Results can provide a better comprehension of cell mechanotransduction for tissue engineering applications. PMID:28546952

  20. Cell cycle-dependent alteration in NAC1 nuclear body dynamics and morphology

    International Nuclear Information System (INIS)

    Wu, Pei-Hsun; Hung, Shen-Hsiu; Ren, Tina; Tseng, Yiider; Shih, Ie-Ming

    2011-01-01

    NAC1, a BTB/POZ family member, has been suggested to participate in maintaining the stemness of embryonic stem cells and has been implicated in the pathogenesis of human cancer. In ovarian cancer, NAC1 upregulation is associated with disease aggressiveness and with the development of chemoresistance. Like other BTB/POZ proteins, NAC1 forms discrete nuclear bodies in non-dividing cells. To investigate the biological role of NAC1 nuclear bodies, we characterized the expression dynamics of NAC1 nuclear bodies during different phases of the cell cycle. Fluorescence recovery after photobleaching assays revealed that NAC1 was rapidly exchanged between the nucleoplasm and NAC1 nuclear bodies in interphase cells. The number of NAC1 bodies significantly increased and their size decreased in the S phase as compared to the G 0 /G 1 and G 2 phases. NAC1 nuclear bodies disappeared and NAC1 became diffuse during mitosis. NAC1 nuclear bodies reappeared immediately after completion of mitosis. These results indicate that a cell cycle-dependent regulatory mechanism controls NAC1 body formation in the nucleus and suggest that NAC1 body dynamics are associated with mitosis or cytokinesis

  1. Morphological and physiological changes induced by contact-dependent interaction between Candida albicans and Fusobacterium nucleatum

    Science.gov (United States)

    Bor, Batbileg; Cen, Lujia; Agnello, Melissa; Shi, Wenyuan; He, Xuesong

    2016-01-01

    Candida albicans and Fusobacterium nucleatum are well-studied oral commensal microbes with pathogenic potential that are involved in various oral polymicrobial infectious diseases. Recently, we demonstrated that F. nucleatum ATCC 23726 coaggregates with C. albicans SN152, a process mainly mediated by fusobacterial membrane protein RadD and Candida cell wall protein Flo9. The aim of this study was to investigate the potential biological impact of this inter-kingdom interaction. We found that F. nucleatum ATCC 23726 inhibits growth and hyphal morphogenesis of C. albicans SN152 in a contact-dependent manner. Further analysis revealed that the inhibition of Candida hyphal morphogenesis is mediated via RadD and Flo9 protein pair. Using a murine macrophage cell line, we showed that the F. nucleatum-induced inhibition of Candida hyphal morphogenesis promotes C. albicans survival and negatively impacts the macrophage-killing capability of C. albicans. Furthermore, the yeast form of C. albicans repressed F. nucleatum-induced MCP-1 and TNFα production in macrophages. Our study suggests that the interaction between C. albicans and F. nucleatum leads to a mutual attenuation of virulence, which may function to promote a long-term commensal lifestyle within the oral cavity. This finding has significant implications for our understanding of inter-kingdom interaction and may impact clinical treatment strategies. PMID:27295972

  2. Modification of Semiconductor Surfaces through Si-N Linkages by Wet-Chemistry Approaches and Modular Functionalization of Zinc Oxide Surfaces for Chemical Protection of Material Morphology

    Science.gov (United States)

    Gao, Fei

    -functionalized carbon nanotubes. 3) Designing a universal method for the modular functionalization of zinc oxide surface for the chemical protection of material morphology.. This project involves surface modification of zinc oxide nanopowder under vacuum condition with propiolic acid, followed by "click" reaction. A combination of spectroscopy and microscopy techniques was utilized to study the surface functionalization and assembly processes. Fourier-transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS) and time of fight secondary ion mass spectroscopy (ToF-SIMS) were employed to elucidate the chemical structure of the modified surface. Atomic force microscopy (AFM), transmission electron microscopy (TEM) and scanning electron microscopy (SEM) were combined to obtain the surface morphological information. Density functional theory (DFT) calculations were applied to confirm the experimental results and to suggest plausible reaction mechanisms. Other complementary techniques for these projects also include nuclear magnetic resonance (NMR) spectroscopy to identify the chemical species on the surface and charge-carrier lifetime measurements to evaluate the electronic property of C60-modified silicon surface.

  3. Morphology-dependent bactericidal activities of Ag/CeO2 catalysts against Escherichia coli.

    Science.gov (United States)

    Wang, Lian; He, Hong; Yu, Yunbo; Sun, Li; Liu, Sijin; Zhang, Changbin; He, Lian

    2014-06-01

    Silver-loaded CeO2 nanomaterials (Ag/CeO2) including Ag/CeO2 nanorods, nanocubes, nanoparticles were prepared with hydrothermal and impregnation methods. Catalytic inactivation of Escherichia coli with Ag/CeO2 catalysts through the formation of reactive oxygen species (ROS) was investigated. For comparison purposes, the bactericidal activities of CeO2 nanorods, nanocubes and nanoparticles were also studied. There was a 3-4 log order improvement in the inactivation of E. coli with Ag/CeO2 catalysts compared with CeO2 catalysts. Temperature-programmed reduction of H2 showed that Ag/CeO2 catalysts had higher catalytic oxidation ability than CeO2 catalysts, which was the reason for that Ag/CeO2 catalysts exhibited stronger bactericidal activities than CeO2 catalysts. Further, the bactericidal activities of CeO2 and Ag/CeO2 depend on their shapes. Results of 5,5-dimethyl-1-pyrroline-N-oxide spin-trapping measurements by electron spin resonance and addition of catalase as a scavenger indicated the formation of OH, O2(-), and H2O2, which caused the obvious bactericidal activity of catalysts. The stronger chemical bond between Ag and CeO2 nanorods led to lower Ag(+) elution concentrations. The toxicity of Ag(+) eluted from the catalysts did not play an important role during the bactericidal process. Experimental results also indicated that Ag/CeO2 induced the production of intracellular ROS and disruption of the cell wall and cell membrane. A possible production mechanism of ROS and bactericidal mechanism of catalytic oxidation were proposed. Copyright © 2014 Elsevier Inc. All rights reserved.

  4. Structure and function of Vibrio cholerae accessory cholera enterotoxin in presence of gold nanoparticles: Dependence on morphology.

    Science.gov (United States)

    Chatterjee, Tanaya; Chatterjee, Barun K; Saha, Tultul; Hoque, Kazi Mirajul; Chakrabarti, Pinak

    2017-05-01

    Accessory cholera enterotoxin (Ace) is a classical enterotoxin produced by Vibrio cholerae, the causative agent for cholera. Considering the crucial role of Ace in pathogenesis of cholera, we explored the modulation of structure/function of Ace using gold nanoparticles (AuNPs) of different size and shape - spherical (AuNS10 and AuNS100, the number indicating the diameter in nm) and rod (AuNR10). Biophysical techniques have been used to find out structural modulation of Ace by AuNPs. Effect of AuNP on Ace conformation was monitored by far-UV CD; urea-induced unfolding and binding of Ace to various AuNPs were studied by tryptophan fluorescence. In vivo experiments using mouse ileal loop and Ussing chamber were carried out to corroborate biophysical data. Biophysical data revealed degradation of Ace by AuNR10 and AuNS100, not by AuNS10. The feature of AuNR10 having high aspect ratio, but with the same transverse diameter as that of AuNS10 enabled us to explore the importance of morphology on modulation of protein structure/function. The equilibration time for adsorption shows dependence on the radius of curvature, being largest for AuNR10. In vivo experiments revealed the efficacy of AuNR10 and AuNS100 for reduced fluid accumulation, indicative of the loss of activity of Ace. We show how biophysical studies and in vivo experiments go hand-in-hand in establishing the efficacy and role of size/shape of AuNPs on a toxin structure. The effect of AuNP on toxin depends on its morphology. The targeted modulation of Ace could be of therapeutic benefit for gastrointestinal disorders. Copyright © 2017 Elsevier B.V. All rights reserved.

  5. Saturn's dayside ultraviolet auroras: Evidence for morphological dependence on the direction of the upstream interplanetary magnetic field

    Science.gov (United States)

    Meredith, C J; Alexeev, I I; Badman, S V; Belenkaya, E S; Cowley, S W H; Dougherty, M K; Kalegaev, V V; Lewis, G R; Nichols, J D

    2014-01-01

    We examine a unique data set from seven Hubble Space Telescope (HST) “visits” that imaged Saturn's northern dayside ultraviolet emissions exhibiting usual circumpolar “auroral oval” morphologies, during which Cassini measured the interplanetary magnetic field (IMF) upstream of Saturn's bow shock over intervals of several hours. The auroras generally consist of a dawn arc extending toward noon centered near ∼15° colatitude, together with intermittent patchy forms at ∼10° colatitude and poleward thereof, located between noon and dusk. The dawn arc is a persistent feature, but exhibits variations in position, width, and intensity, which have no clear relationship with the concurrent IMF. However, the patchy postnoon auroras are found to relate to the (suitably lagged and averaged) IMF Bz, being present during all four visits with positive Bz and absent during all three visits with negative Bz. The most continuous such forms occur in the case of strongest positive Bz. These results suggest that the postnoon forms are associated with reconnection and open flux production at Saturn's magnetopause, related to the similarly interpreted bifurcated auroral arc structures previously observed in this local time sector in Cassini Ultraviolet Imaging Spectrograph data, whose details remain unresolved in these HST images. One of the intervals with negative IMF Bz however exhibits a prenoon patch of very high latitude emission extending poleward of the dawn arc to the magnetic/spin pole, suggestive of the occurrence of lobe reconnection. Overall, these data provide evidence of significant IMF dependence in the morphology of Saturn's dayside auroras. Key Points We examine seven cases of joint HST Saturn auroral images and Cassini IMF data The persistent but variable dawn arc shows no obvious IMF dependence Patchy postnoon auroras are present for northward IMF but not for southward IMF PMID:26167441

  6. The size prediction of potential inclusions embedded in the sub-surface of fused silica by damage morphology

    Directory of Open Access Journals (Sweden)

    Gao Xiang

    2017-04-01

    Full Text Available A model for predicting the size ranges of different potential inclusions initiating damage on the surface of fused silica has been presented. This accounts for the heating of nanometric inclusions whose absorptivity is described based on Mie Theory. The depth profile of impurities has been measured by ICP-OES. By the measured temporal pulse profile on the surface of fused silica, the temperature and thermal stress has been calculated. Furthermore, considering the limit conditions of temperature and thermal stress strength for different damage morphologies, the size range of potential inclusions for fused silica is discussed.

  7. The size prediction of potential inclusions embedded in the sub-surface of fused silica by damage morphology

    Science.gov (United States)

    Gao, Xiang; Qiu, Rong; Wang, Kunpeng; Zhang, Jiangmei; Zhou, Guorui; Yao, Ke; Jiang, Yong; Zhou, Qiang

    2017-04-01

    A model for predicting the size ranges of different potential inclusions initiating damage on the surface of fused silica has been presented. This accounts for the heating of nanometric inclusions whose absorptivity is described based on Mie Theory. The depth profile of impurities has been measured by ICP-OES. By the measured temporal pulse profile on the surface of fused silica, the temperature and thermal stress has been calculated. Furthermore, considering the limit conditions of temperature and thermal stress strength for different damage morphologies, the size range of potential inclusions for fused silica is discussed.

  8. Morphology and phase behavior of ethanol nanodrops condensed on chemically patterned surfaces

    Science.gov (United States)

    Checco, Antonio; Ocko, Benjamin M.

    2008-06-01

    Equilibrium wetting of ethanol onto chemically patterned nanostripes has been investigated using environmental atomic force microscopy (AFM) in noncontact mode. The chemical patterns are composed of COOH-terminated “wetting” regions and CH3 -terminated “nonwetting” regions. A specially designed environmental AFM chamber allowed for accurate measurements of droplet height as a function of the temperature offset between the substrate and a macroscopic ethanol reservoir. At saturation, the height dependence scales with droplet width according to w1/2 , in excellent agreement with the augmented Young equation (AYE) modeled with dispersive, nonretarded surface potentials. At small under- and oversaturations, the AYE model accurately fits the data if an effective ΔT is used as a fitting parameter. There is a systematic difference between the measured ΔT and the values extracted from the fits to the data. In addition to static measurements, we present time-resolved measurements of the droplet height which enable the study of condensation-evaporation dynamics of nanometer-scale drops.

  9. Chloride ion-dependent surface-enhanced Raman scattering study of biotin on the silver surface

    International Nuclear Information System (INIS)

    Liu Fangfang; Gu Huaimin; Yuan Xiaojuan; Dong Xiao; Lin Yue

    2011-01-01

    In the present paper, the surface enhanced Raman scattering (SERS) technique was employed to study the SERS spectra of biotin molecules formed on the silver surface. The adsorption geometries of biotin molecules on the silver surface were analyzed based on the SERS data. It can be found that most vibration modes show a Raman shift in silver sol after the addition of sodium chloride solution. In addition, The Raman signals of biotin become weaker and weaker with the increase of the concentration of sodium chloride. This may be due to that the interaction between chloride ions and silver particles is stronger than the interaction between biotin molecules and silver particles. When the concentration of sodium chloride in silver colloid is higher than 0.05mol/L, superfluous chloride ions may form an absorption layer so that biotin can not be adsorbed on silver surface directly. The changes in intensity and profile shape in the SERS spectra suggest different adsorption behavior and surface-coverage of biotin on silver surface. The SERS spectra of biotin suggest that the contribution of the charge transfer mechanism to SERS may be dominant.

  10. Effects of Surface Morphology of ZnAl2O4 Ceramic Materials on Osteoblastic Cells Responses

    Directory of Open Access Journals (Sweden)

    José Luis Suárez-Franco

    2013-01-01

    Full Text Available Ceramic scaffolds are widely studied in the tissue engineering field due to their potential in medical applications as bone substitutes or as bone-filling materials. The purpose of this study was to investigate the effect of surface morphology of nanostructure thin films of ZnAl2O4 prepared by spray pyrolysis and bulk pellets of polycrystalline ZnAl2O4 prepared by chemical coprecipitation reaction on the in vitro cell adhesion, viability, and cell-material interactions of osteoblastic cells. Our result showed that cell attachment was significantly enhanced from 60 to 80% on the ZnAl2O4 nanostructured material surface when compared with bulk ceramic surfaces. Moreover, our results showed that the balance of morphological properties of the thin film nanostructure ceramic improves cell-material interaction with enhanced spreading and filopodia with multiple cellular extensions on the surface of the ceramic and enhancing cell viability/proliferation in comparison with bulk ceramic surfaces used as control. Altogether, these results suggest that zinc aluminate nanostructured materials have a great potential to be used in dental implant and bone substitute applications.

  11. The use of an ion-beam source to alter the surface morphology of biological implant materials

    Science.gov (United States)

    Weigand, A. J.

    1978-01-01

    An electron-bombardment ion-thruster was used as a neutralized-ion-beam sputtering source to texture the surfaces of biological implant materials. The materials investigated included 316 stainless steel; titanium-6% aluminum, 4% vanadium; cobalt-20% chromium, 15% tungsten; cobalt-35% nickel, 20% chromium, 10% molybdenum; polytetrafluoroethylene; polyoxymethylene; silicone and polyurethane copolymer; 32%-carbon-impregnated polyolefin; segmented polyurethane; silicone rubber; and alumina. Scanning electron microscopy was used to determine surface morphology changes of all materials after ion-texturing. Electron spectroscopy for chemical analysis was used to determine the effects of ion-texturing on the surface chemical composition of some polymers. Liquid contact angle data were obtained for ion-textured and untextured polymer samples. Results of tensile and fatigue tests of ion-textured metal alloys are presented. Preliminary data of tissue response to ion-textured surfaces of some metals, polytetrafluoroethylene, alumina, and segmented polyurethane have been obtained.

  12. Ion beam sputter modification of the surface morphology of biological implants

    Science.gov (United States)

    Weigand, A. J.; Banks, B. A.

    1976-01-01

    The surface chemistry and texture of materials used for biological implants may significantly influence their performance and biocompatibility. Recent interest in the microscopic control of implant surface texture has led to the evaluation of ion beam sputtering as a potentially useful surface roughening technique. Ion sources, similar to electron bombardment ion thrusters designed for propulsive applications, are used to roughen the surfaces of various biocompatible alloys or polymer materials. These materials are typically used for dental implants, orthopedic prostheses, vascular prostheses, and artificial heart components. Masking techniques and resulting surface textures are described along with progress concerning evaluation of the biological response to the ion beam sputtered surfaces.

  13. Morphological and Molecular Identification of Acanthamoeba Spp from Surface Waters in Birjand, Iran, During 2014-2015

    Directory of Open Access Journals (Sweden)

    Mahmoodreza Behravan

    2016-04-01

    Full Text Available Background & Aims of the Study: Free-living amoebae (FLA are opportunistic and ubiquitous protozoa that are widely found in various environmental sources. They are known to cause serious human infections including a fatal encephalitis, a blinding keratitis, and pneumonia. So, due to their medical importance, the identification of free living amoeba in water resources, as a source of human infection, is necessary. The objective of this study was to isolate the Acanthamoebaspp from the surface waters of Birjand, Iran, during 2014-2015 by Morphological and molecular method. Materials and Methods:  In a cross-sectional study, 50 samples were collected from different localities of Birjand city including the surface waters, pools and fountains in parks,squares and water stations from the October 2014 to the January 2015.Each sample was filtered through a nitrocellulose membrane filters and cultured on non-nutrient agar (NNA with Escherichia coli suspension and incubated for 1 week to 2 months at room temperature.The plates were examined by the microscopy to morphologically identify Acanthamoeba species. Following DNA extraction, PCR specific primers was used to confirm the identification morphologically. Results:  Out of 50 water samples, 19 (38% were positive for Acanthamoebatrophozoites and cysts according to the morphological criteria. In addition, Acanthamoebaspp was identified by PCR method, using genus specific primers pairs in 15 (78.9% cases of positive cultures, showing anearly 500bp band. Conclusion: According to the prevalent of Acanthamoebaspp in the surface stagnant waters of Birjand, more attention to the potential role of such waters in transmission of infection by the regional clinicians and health practitioners is necessary.

  14. Bulk and surface morphologies of ABC miktoarm star terpolymers comprised of PDMS, PI and PMMA arms

    DEFF Research Database (Denmark)

    Chernyy, Sergey; Kirkensgaard, Jacob Judas Kain; Mahalik, Jyoti P.

    2018-01-01

    . The thin film morphologies, which differ from those found in the bulk, were identified by scanning electron microscopy, coupled with oxygen plasma etching. Square arrays of the PDMS nanodots and empty core cylinders were formed on silica after oxygen plasma removal of the poly(1,4-isoprene) and poly...

  15. Dry- and Swollen-State Morphology of Novel High Surface Area Polymers

    Czech Academy of Sciences Publication Activity Database

    Sterchele, S.; Centomo, P.; Zecca, M.; Hanková, Libuše; Jeřábek, Karel

    2014-01-01

    Roč. 185, FEB 1 (2014), s. 26-29 ISSN 1387-1811 R&D Projects: GA MŠk LH12194 Institutional support: RVO:67985858 Keywords : porous polymers * morphology * swollen state Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 3.453, year: 2014

  16. Tracking changes of river morphology in Ayeyarwady River in Myanmar using earth observations and surface water mapping tool

    Science.gov (United States)

    Piman, T.; Schellekens, J.; Haag, A.; Donchyts, G.; Apirumanekul, C.; Hlaing, K. T.

    2017-12-01

    River morphology changes is one of the key issues in Ayeyarwady River in Myanmar which cause impacts on navigation, riverine habitats, agriculture lands, communities and livelihoods near the bank of the river. This study is aimed to track the changes in river morphology in the middle reach of Ayeyarwady River over last 30 years from 1984-2014 to improve understanding of riverbank dynamic, erosion and deposition procress. Earth observations including LandSat-7, LandSat-8, Digital Elevation Model from SRTM Plus and, ASTER-2 GoogleMap and Open Street Map were obtained for the study. GIS and remote sensing tools were used to analyze changes in river morphology while surface water mapping tool was applied to determine how the dynamic behaviour of the surface river and effect of river morphology changes. The tool consists of two components: (1) a Google Earth Engine (GEE) javascript or python application that performs image analysis and (2) a user-friendly site/app using Google's appspot.com that exposes the application to the users. The results of this study shown that the fluvial morphology in the middle reach of Ayeyarwady River is continuously changing under the influence of high water flows in particularly from extreme flood events and land use change from mining and deforestation. It was observed that some meandering sections of the riverbank were straightened, which results in the movement of sediment downstream and created new sections of meandering riverbank. Several large islands have formed due to the stabilization by vegetation and is enforced by sedimentation while many small bars were formed and migrated dynamically due to changes in water levels and flow velocity in the wet and dry seasons. The main channel was changed to secondary channel in some sections of the river. This results a constant shift of the navigation route. We also found that some villages were facing riverbank erosion which can force villagers to relocate. The study results demonstrated

  17. Morphology and optical properties of aluminum oxide formed into oxalic electrolyte with addition surface active agents

    International Nuclear Information System (INIS)

    Kazarkin, B; Stsiapanau, A; Smirnov, A; Zhilinski, V; Chernik, A; Bezborodov, V; Kozak, G; Danilovich, S

    2016-01-01

    The article discusses the results of investigations of porous films of alumina, formed into oxalic electrolyte with addition surface active agents, in particular, ordering structure, roughness of a surface, the optical transparency of the electrolyte concentration and surface active agents. Also discusses the features of the formation of porous films of temperature and IR radiation. (paper)

  18. Morphological evaluation of cavity preparation surface after duraphat and Er:YAG laser treatment by scanning electronic microscopy

    International Nuclear Information System (INIS)

    Rodrigues, Luciane Borelli

    2002-01-01

    The treatment of dental surface using different lasers to prevent dental caries has been studied for several on last years. The purpose of this in vitro study was to evaluate the morphological changes on dentin surface from pulpal wall of cavity preparations performed by high-speed drill, treated with 2,26% fluoride varnish (Duraphat) and Er:YAG laser, and then submitted after receiving or not to EDTA 15% treatment. Twenty Class V cavities were performed on ten humans molars. The specimens were randomly divided in to 4 groups: group 1- treatment with Duraphat followed by Er:YAG laser irradiation (120 mJ/ 4 Hz); group 2: Er:YAG laser irradiation, same parameters, followed by Duraphat treatment; group 3- same group 1 followed by immersion in EDTA (5 min); group 4 - same as group 2 followed by immersion in EDTA (5 min). The specimens were processed for SEM analysis. The micrographs showed that Duraphat treatment promoted morphological changes on dentin, closing dentinal tubules; the specimens treated by Duraphat and Er:YAG laser and immersed in EDTA (group 3) showed homogeneous surface, closed and protected dentinal tubules, maintenance of the fluoride varnish on the dentin surface and around the dentinal tubules, showing feasible and efficiency of these therapies the feasibility.(author)

  19. Morphology of the lingual surface of South American fur seal (Arctocephalus australis) and sea lion (Otaria flavescens).

    Science.gov (United States)

    Erdoğan, Serkan; Villar Arias, Silvia; Pérez, William

    2015-02-01

    In this study, we aimed to describe the morphological characteristics of the lingual papillae in two species of Otariidae family by stereomicroscopy and scanning electron microscopy. We used tongues of two South American Otariidae species. The tongues were elongated and terminated in bifid apex and there was no median sulcus on the dorsal lingual surface. The most numerous type of lingual papilla was filiform in the South American fur seal (SASL) and entire dorsal lingual surface was covered by these filiform papillae but the dorsal surface of the tongue of the South American sea lion was covered by numerous polygonal projections, which were different in size. Fungiform papillae were detected in only SASL and they randomly distributed on the lingual apex and body, and some fungiform papillae were collected into twosome or threesome groups on the posterior part of the lingual body. Circumvallate papilla was found in the center of the lingual radix of South American sea lion. Thread-like conical papillae were common for both species and they located on the lingual radix. We determined that lingual surface morphology was completely different in each species, although they were members of the same family, Otariidae. © 2014 Wiley Periodicals, Inc.

  20. Rough surface electrical contact resistance considering scale dependent properties and quantum effects

    International Nuclear Information System (INIS)

    Jackson, Robert L.; Crandall, Erika R.; Bozack, Michael J.

    2015-01-01

    The objective of this work is to evaluate the effect of scale dependent mechanical and electrical properties on electrical contact resistance (ECR) between rough surfaces. This work attempts to build on existing ECR models that neglect potentially important quantum- and size-dependent contact and electrical conduction mechanisms present due to the asperity sizes on typical surfaces. The electrical conductance at small scales can quantize or show a stepping trend as the contact area is varied in the range of the free electron Fermi wavelength squared. This work then evaluates if these effects remain important for the interface between rough surfaces, which may include many small scale contacts of varying sizes. The results suggest that these effects may be significant in some cases, while insignificant for others. It depends on the load and the multiscale structure of the surface roughness

  1. Dependence of surface distribution of self-assembled InSb nanodots on surface morphology and spacer layer thickness

    International Nuclear Information System (INIS)

    Godbole, M.; Olivier, E.J.; Coetsee, E.; Swart, H.C.; Neethling, J.H.; Botha, J.R.

    2012-01-01

    Self-assembled InSb nanodots (NDs) were grown on a GaSb (1 0 0) substrate using metal-organic vapour phase epitaxy (MOVPE). The effects of etching depth of the substrate and thickness of the GaSb buffer layer on the density and size distribution of single and double layer dots were studied for detector applications. The etch depth of the substrate was varied up to 30 μm. In this particular study, the dots were grown at 450 °C and the GaSb spacer thickness was varied between 50 nm and 200 nm. The optimum substrate etch depth was found to be 30 μm while the best spacer thickness was found to be 200 nm.

  2. Surface dependent behaviour of CdS LO-phonon mode

    International Nuclear Information System (INIS)

    Molina-Contreras, J R; Medina-Gutierrez, C; Frausto-Reyes, C; Trejo-Vazquez, R; Villalobos-Pina, F J; Romo-Luevano, G; Calixto, S

    2007-01-01

    In this paper, we develop a sensitive optical method to monitor the surface roughness in the investigation of surfaces. By applying this method to measure the RMS surface roughness of various surfaces, we found RMS values which are comparable to those obtained by atomic force microscopy measurements. In addition, we present a simple empirical model to calculate the RMS surface roughness which shows very good agreement with the surface roughness measurements taken by the method reported in this paper. Finally, the application of our method to the study of the LO-phonon mode of CdS suggests that its intensity is dominated by the surface roughness. This roughness dependent behaviour of the CdS LO-phonon mode is experimentally confirmed by using an excitation wavelength near its E 0 transition

  3. Surface dependent behaviour of CdS LO-phonon mode

    Energy Technology Data Exchange (ETDEWEB)

    Molina-Contreras, J R [Departamento de IngenierIa Electrica y Electronica, Instituto Tecnologico de Aguascalientes, Av. Lopez Mateos 1081 Oriente, Fracc. Bonna Gens, CP 20256. Aguascalientes, Ags. (Mexico); Medina-Gutierrez, C [Universidad de Guadalajara, Centro Universitario de los Lagos, Av. Enrique DIaz de Leon s/n, Fracc. Paseos de la Montana, CP 47460, Lagos de Moreno, Jal. (Mexico); Frausto-Reyes, C [Centro de Investigaciones en Optica AC, Unidad Aguascalientes, Prolong., Constitucion 607, Fracc. Reserva Loma Bonita, CP 20200, Apartado Postal 507, Ags. (Mexico); Trejo-Vazquez, R [Departamento de IngenierIa Electrica y Electronica, Instituto Tecnologico de Aguascalientes, Av. Lopez Mateos 1081 Oriente, Fracc. Bonna Gens, CP 20256. Aguascalientes, Ags. (Mexico); Villalobos-Pina, F J [Departamento de IngenierIa Electrica y Electronica, Instituto Tecnologico de Aguascalientes, Av. Lopez Mateos 1081 Oriente, Fracc. Bonna Gens, CP 20256. Aguascalientes, Ags. (Mexico); Romo-Luevano, G [Intel TecnologIa de Mexico, SA de CV, Systems Research Center-Mexico, Parque Industrial Tecnologico II, Periferico Sur 7980, edificio 4-E, 45600 Tlaquepaque, Jalisco (Mexico); Calixto, S [Centro de Investigaciones en Optica, AC, Loma del Bosque 115, Colonia Lomas del Campestre, CP 37150 Leon, Guanajuato (Mexico)

    2007-08-21

    In this paper, we develop a sensitive optical method to monitor the surface roughness in the investigation of surfaces. By applying this method to measure the RMS surface roughness of various surfaces, we found RMS values which are comparable to those obtained by atomic force microscopy measurements. In addition, we present a simple empirical model to calculate the RMS surface roughness which shows very good agreement with the surface roughness measurements taken by the method reported in this paper. Finally, the application of our method to the study of the LO-phonon mode of CdS suggests that its intensity is dominated by the surface roughness. This roughness dependent behaviour of the CdS LO-phonon mode is experimentally confirmed by using an excitation wavelength near its E{sub 0} transition.

  4. Influence of GaAs Substrate Orientation on InAs Quantum Dots: Surface Morphology, Critical Thickness, and Optical Properties

    Directory of Open Access Journals (Sweden)

    Liang BL

    2007-01-01

    Full Text Available AbstractInAs/GaAs heterostructures have been simultaneously grown by molecular beam epitaxy on GaAs (100, GaAs (100 with a 2° misorientation angle towards [01−1], and GaAs (n11B (n = 9, 7, 5 substrates. While the substrate misorientation angle increased from 0° to 15.8°, a clear evolution from quantum dots to quantum well was evident by the surface morphology, the photoluminescence, and the time-resolved photoluminescence, respectively. This evolution revealed an increased critical thickness and a delayed formation of InAs quantum dots as the surface orientation departed from GaAs (100, which was explained by the thermal-equilibrium model due to the less efficient of strain relaxation on misoriented substrate surfaces.

  5. Solvent-induced synthesis of nitrogen-doped hollow carbon spheres with tunable surface morphology for supercapacitors

    Science.gov (United States)

    Liu, Feng; Yuan, Ren-Lu; Zhang, Ning; Ke, Chang-Ce; Ma, Shao-Xia; Zhang, Ru-Liang; Liu, Lei

    2018-04-01

    Nitrogen doped hollow carbon spheres (NHCSs) with tunable surface morphology have been prepared through one-pot carbonization method by using melamine-formaldehyde spheres as template and resorcinol-based resin as carbon precursor in ethanol-water solution. Well-dispersed NHCSs with particle size of 800 nm were obtained and the surface of NHCSs turn from smooth to tough, wrinkled, and finally concave by increasing the ethanol concentration. The fabricated NHCSs possessed high nitrogen content (3.99-4.83%) and hierarchical micro-dual mesoporous structure with surface area range of 265-405 m2 g-1 and total pore volume of 0.18-0.29 cm3 g-1, which contributed to high specific capacitance, excellent rate capability and long cycle life.

  6. Influence of surface physicochemistry and morphology of TA6V substrates on the mechanical resistance of thin layers of alumina

    International Nuclear Information System (INIS)

    Abgrall, E.; Desmaison, J.; Haure, T.; Tixier, C.; Jonnard, P.

    2004-01-01

    Substrate surface preparation before chemical vapor deposition is an important step for the adhesion. This study describes the influence of the temperature and the RF bias during in-situ argon plasma treatment on TA6V substrates just before plasma enhanced chemical vapor deposition (PECVD) of alumina. Substrates were treated under oxygen plasma without introducing aluminum precursor during 90 seconds under process PECVD conditions that were later used for coatings development. The surface of the samples is analyzed by electron induced X-ray emission spectroscopy to study the physicochemical environment around the aluminum atoms. Atomic force microscopy (AFM) allowed to show the treatment impact on the surface morphology of the substrates. Coatings were characterized by the multicracking 4-point bending test. The results pointed out that the polarization value has a minor effect, whereas the temperature has a major influence. (orig.)

  7. On geometry-dependent vortex stability and topological spin excitations on curved surfaces with cylindrical symmetry

    Energy Technology Data Exchange (ETDEWEB)

    Carvalho-Santos, V.L., E-mail: vagson.santos@bonfim.ifbaiano.edu.br [Instituto Federal de Educação, Ciência e Tecnologia Baiano – Senhor do Bonfim, 48970-000 Senhor do Bonfim, Bahia (Brazil); Apolonio, F.A. [Departamento de Física, Universidade Federal de Viçosa, 36570-000 Viçosa, Minas Gerais (Brazil); Oliveira-Neto, N.M. [Departamento de Química e Exatas, Universidade Estadual do Sudoeste da Bahia, 45206-190 Jequié, Bahia (Brazil)

    2013-08-01

    We study the Heisenberg model on cylindrically symmetric curved surfaces. Two kinds of excitations are considered. The first is given by the isotropic regime, yielding the sine-Gordon equation and π solitons are predicted. The second one is given by the XY model, leading to a vortex turning around the surface. Helical states are also considered, however, topological arguments cannot be used to ensure its stability. The energy and the anisotropy parameter which stabilizes the vortex state are explicitly calculated for two surfaces: catenoid and hyperboloid. The results show that the anisotropy and the vortex energy depends on the underlying geometry. -- Highlights: •Applying the anisotropic Heisenberg model on curved surfaces. •Appearance of topological solitons on curved surfaces with cylindrical symmetry. •Calculus of the vortex energy, which depends on curvature. •Discussion on features of non-topological helical-like states. •Vortex stability ensured by the anisotropy parameter value.

  8. [Possible Involvement of Surface Antigen Protein 2 in the Morphological Transition and Biofilm Formation of Candida albicans].

    Science.gov (United States)

    Okamoto-Shibayama, Kazuko; Kikuchi, Yuichiro; Kokubu, Eitoyo; Ishihara, Kazuyuki

    2017-01-01

    Surface antigen protein 2 (Csa2) is a member of the Candida albicans Common in Fungal Extracellular Membranes (CFEM) protein superfamily. We previously established its role in iron acquisition in C. albicans. However, the other roles of Csa2 remain unknown. Here, we compared growth, morphological transition, and biofilm formation among wild-type, Csa2-mutant, and complemented strains of C. albicans. Deletion of the Csa2 gene resulted in smaller and reduced colony growth, significant attenuation of the dimorphic transition under serum-inducing conditions, and reduced biofilm formation; complementation restored these levels to those of the wild-type. Our findings demonstrated that Csa2 participated in yeast-to-hyphae morphological switching under serum-inducing conditions and contributed to the biofilm formation of C. albicans. This work, therefore, provides novel insights into the potential roles of Csa2 in virulence of C. albicans.

  9. Morphology and grain structure evolution during epitaxial growth of Ag films on native-oxide-covered Si surface

    International Nuclear Information System (INIS)

    Hur, Tae-Bong; Kim, Hong Koo; Perello, David; Yun, Minhee; Kulovits, Andreas; Wiezorek, Joerg

    2008-01-01

    Epitaxial nanocrystalline Ag films were grown on initially native-oxide-covered Si(001) substrates using radio-frequency magnetron sputtering. Mechanisms of grain growth and morphology evolution were investigated. An epitaxially oriented Ag layer (∼5 nm thick) formed on the oxide-desorbed Si surface during the initial growth phase. After a period of growth instability, characterized as kinetic roughening, grain growth stagnation, and increase of step-edge density, a layer of nanocrystalline Ag grains with a uniform size distribution appeared on the quasi-two-dimensional layer. This hierarchical process of film formation is attributed to the dynamic interplay between incoming energetic Ag particles and native oxide. The cyclic interaction (desorption and migration) of the oxide with the growing Ag film is found to play a crucial role in the characteristic evolution of grain growth and morphology change involving an interval of grain growth stagnation

  10. Surface roughness and morphology of dental nanocomposites polished by four different procedures evaluated by a multifractal approach

    Energy Technology Data Exchange (ETDEWEB)

    Ţălu, Ştefan, E-mail: stefan_ta@yahoo.com [Technical University of Cluj-Napoca, Faculty of Mechanical Engineering, Department of AET, Discipline of Descriptive Geometry and Engineering Graphics, 103-105 B-dul Muncii St., Cluj-Napoca 400641, Cluj (Romania); Stach, Sebastian, E-mail: sebastian.stach@us.edu.pl [University of Silesia, Faculty of Computer Science and Materials Science, Institute of Informatics, Department of Biomedical Computer Systems, Będzińska 39, 41-205 Sosnowiec (Poland); Lainović, Tijana, E-mail: tijana.lainovic@gmail.com [University of Novi Sad, Faculty of Medicine, School of Dentistry, Hajduk Veljkova 3, 21000 Novi Sad (Serbia); Vilotić, Marko, E-mail: markovil@uns.ac.rs [University of Novi Sad, Faculty of Technical Sciences, Department for Production Engineering, Trg Dositeja Obradovića 6, 21000 Novi Sad (Serbia); Blažić, Larisa, E-mail: larisa.blazic@gmail.com [University of Novi Sad, Faculty of Medicine, School of Dentistry, Clinic of Dentistry of Vojvodina, Department of Restorative Dentistry and Endodontics, Hajduk Veljkova 3, 21000 Novi Sad (Serbia); Alb, Sandu Florin, E-mail: albflorin@yahoo.com [“Iuliu Haţieganu” University of Medicine and Pharmacy, Faculty of Dentistry, Department of Periodontology, 8 Victor Babeş St., 400012 Cluj-Napoca (Romania); Kakaš, Damir, E-mail: kakasdam@uns.ac.rs [University of Novi Sad, Faculty of Technical Sciences, Department for Production Engineering, Trg Dositeja Obradovića 6, 21000 Novi Sad (Serbia)

    2015-03-01

    Graphical abstract: - Highlights: • Multifractals are good indicators of polished dental composites 3-D surface structure. • The nanofilled composite had superior 3-D surface properties than the nanohybrid one. • Composite polishing with diamond paste created improved 3-D multifractal structure. • Recommendation: polish the composite with diamond paste if using the one-step tool. • Multifractal analysis could become essential in designing new dental surfaces. - Abstract: The objective of this study was to determine the effect of different dental polishing methods on surface texture parameters of dental nanocomposites. The 3-D surface morphology was investigated by atomic force microscopy (AFM) and multifractal analysis. Two representative dental resin-based nanocomposites were investigated: a nanofilled and a nanohybrid composite. The samples were polished by two dental polishing protocols using multi-step and one-step system. Both protocols were then followed by diamond paste polishing. The 3-D surface roughness of samples was studied by AFM on square areas of topography on the 80 × 80 μm{sup 2} scanning area. The multifractal spectrum theory based on computational algorithms was applied for AFM data and multifractal spectra were calculated. The generalized dimension D{sub q} and the singularity spectrum f(α) provided quantitative values that characterize the local scale properties of dental nanocomposites polished by four different dental polishing protocols at nanometer scale. The results showed that the larger the spectrum width Δα (Δα = α{sub max} − α{sub min}) of the multifractal spectra f(α), the more non-uniform was the surface morphology. Also, the 3-D surface topography was described by statistical parameters, according to ISO 25178-2:2012. The 3-D surface of samples had a multifractal nature. Nanofilled composite had lower values of height parameters than nanohybrid composites, due to its composition. Multi-step polishing protocol

  11. Synthesis and processing of ELISA polymer substitute: The influence of surface chemistry and morphology on detection sensitivity

    International Nuclear Information System (INIS)

    Hosseini, Samira; Ibrahim, Fatimah; Djordjevic, Ivan; Rothan, Hussin A.; Yusof, Rohana; Marel, Cees van der; Koole, Leo H.

    2014-01-01

    Highlights: • Polyacrylate coatings with controlled surface functionalities. • Impact of surface chemistry and morphology on dengue antibody immobilization. • Enhancement of detection signal as a result of bio-activation of polymer surface. - Abstract: Despite the known drawbacks of enzyme-linked immunosorbent assay (ELISA), one of the deficiencies that have relatively been ignored is the performance of ELISA substrate itself. Polystyrene (PS), as the cost effective material of choice for mass production of ELISA well-plates, has shown obvious lacks of suitable physical and chemical properties for protein attachment. The general concept of this work was to develop a potential substrate that can be suggested as a material of choice for production of a new generation of ELISA analytical kits. Spin-coated thin films of polymethyl methacrylate-co-methacrylic acid (PMMA-co-MAA) on silicon surfaces were designed and processed for detection of dengue virus. Coated surfaces of different molar ratios have been investigated as carboxyl-functionalized layers for obtaining platform for biomolecule immobilization with high level of protein activity. To improve the sensitivity of detection, we have used amine functional “spacers”, hexamethylenediamine (HMDA) and polyethyleneimine (PEI), which were covalently bonded to the surfaces of PMMA-co-MAA coatings. Results demonstrate that the variation of surface concentration of carboxyl groups of PMMA-co-MAA can be used to control the amine surface concentration after carbodiimide coupling with HMDA and PEI spacers. The presence of amine spacers increases hydrophilicity of the coatings and significantly impacts the polymer surface morphology. In particular, protein immobilization via amine-bearing spacers has been achieved in two effective steps: (1) carbodiimide bonding between amine spacer molecules and PMMA-co-MAA polymer coatings; and (2) covalent immobilization of antibody via glutaraldehyde reaction with amine groups

  12. Synthesis and processing of ELISA polymer substitute: The influence of surface chemistry and morphology on detection sensitivity

    Energy Technology Data Exchange (ETDEWEB)

    Hosseini, Samira; Ibrahim, Fatimah [Department of Biomedical Engineering, Faculty of Engineering, University of Malaya, Kuala Lumpur 50603 (Malaysia); Center for Innovation in Medical Engineering, Faculty of Engineering, University of Malaya, Kuala Lumpur 50603 (Malaysia); Djordjevic, Ivan, E-mail: ivan.djordjevic@um.edu.my [Department of Biomedical Engineering, Faculty of Engineering, University of Malaya, Kuala Lumpur 50603 (Malaysia); Center for Innovation in Medical Engineering, Faculty of Engineering, University of Malaya, Kuala Lumpur 50603 (Malaysia); Rothan, Hussin A.; Yusof, Rohana [Department of Molecular Medicine, Faculty of Medicine, University of Malaya, 50603 Kuala Lumpur (Malaysia); Marel, Cees van der [Philips Materials Analysis, High Tech Campus 11, 5656 AE Eindhoven (Netherlands); Koole, Leo H. [Department of Biomedical Engineering, Faculty of Engineering, University of Malaya, Kuala Lumpur 50603 (Malaysia); Center for Innovation in Medical Engineering, Faculty of Engineering, University of Malaya, Kuala Lumpur 50603 (Malaysia); Faculty of Health, Medicine and Life Sciences, Maastricht University (Netherlands)

    2014-10-30

    Highlights: • Polyacrylate coatings with controlled surface functionalities. • Impact of surface chemistry and morphology on dengue antibody immobilization. • Enhancement of detection signal as a result of bio-activation of polymer surface. - Abstract: Despite the known drawbacks of enzyme-linked immunosorbent assay (ELISA), one of the deficiencies that have relatively been ignored is the performance of ELISA substrate itself. Polystyrene (PS), as the cost effective material of choice for mass production of ELISA well-plates, has shown obvious lacks of suitable physical and chemical properties for protein attachment. The general concept of this work was to develop a potential substrate that can be suggested as a material of choice for production of a new generation of ELISA analytical kits. Spin-coated thin films of polymethyl methacrylate-co-methacrylic acid (PMMA-co-MAA) on silicon surfaces were designed and processed for detection of dengue virus. Coated surfaces of different molar ratios have been investigated as carboxyl-functionalized layers for obtaining platform for biomolecule immobilization with high level of protein activity. To improve the sensitivity of detection, we have used amine functional “spacers”, hexamethylenediamine (HMDA) and polyethyleneimine (PEI), which were covalently bonded to the surfaces of PMMA-co-MAA coatings. Results demonstrate that the variation of surface concentration of carboxyl groups of PMMA-co-MAA can be used to control the amine surface concentration after carbodiimide coupling with HMDA and PEI spacers. The presence of amine spacers increases hydrophilicity of the coatings and significantly impacts the polymer surface morphology. In particular, protein immobilization via amine-bearing spacers has been achieved in two effective steps: (1) carbodiimide bonding between amine spacer molecules and PMMA-co-MAA polymer coatings; and (2) covalent immobilization of antibody via glutaraldehyde reaction with amine groups

  13. Optical properties and surface morphology of ZnTe thin films prepared by multiple potential steps

    Energy Technology Data Exchange (ETDEWEB)

    Gromboni, Murilo F.; Lucas, Francisco W. S.; Mascaro, Lucia H., E-mail: lmascaro@ufscar.br [Universidade de Federal de Sao Carlos (LIEC/UFSCar), SP (Brazil). Departamento de Quimica. Lab. de Eletroquimica e Ceramica

    2014-03-15

    In this work, the ZnTe thin films were electrodeposited using potentiostatic steps, on Pt substrate. The effect of steps number, the deposition time for each element (Zn or Te) and layer order (Zn/Te or Te/Zn) in the morphology, composition, band gap energy and photocurrent was evaluated. Microanalysis data showed that the ratio Zn/Te ranged from 0.12 and 0.30 and the film was not stoichiometric. However, the band-gap value obtained from in all experimental conditions used in this work was 2.28 eV, indicating film growth of ZnTe. The samples with higher Zn showed higher photocurrent, which was of the order of 2.64 μA cm{sup -2} and dendritic morphology (author)

  14. METABOLIC AND MORPHOLOGICAL OBSERVATIONS ON THE EFFECT OF SURFACE-ACTIVE AGENTS ON LEUKOCYTES

    Science.gov (United States)

    Graham, R. C.; Karnovsky, M. J.; Shafer, A. W.; Glass, E. A.; Karnovsky, Manfred L.

    1967-01-01

    Morphological and metabolic observations have been made on the effects of endotoxin, deoxycholate, and digitonin (at less than 50 µg/ml) on polymorphonuclear leukocytes and mononuclear cells. The agents stimulate the respiration and glucose oxidation of these cells in a manner similar to that seen during phagocytosis. Electron microscopy revealed no morphological changes with the first two agents, but dramatic membrane changes were seen in the case of digitonin. Here tubular projections of characteristic size and shape formed on and split off the membrane. All the agents stimulated uptake of inulin, but efforts to demonstrate increased pinocytosis by electron microscopy have not so far succeeded, probably due to limitations in present experimental techniques. PMID:6034482

  15. The effects of deposition parameters on surface morphology and crystallographic orientation of electroless Ni-B coatings

    Science.gov (United States)

    Bulbul, Ferhat

    2011-02-01

    Electroless Ni-B coatings were deposited on AISI 304 stainless steels by electroless deposition method, which was performed for nine different test conditions at various levels of temperature, concentration of NaBH4, concentration of NiCl2, and time, using the Taguchi L9(34) experimental method. The effects of deposition parameters on the crystallographic orientation of electroless Ni-B coatings were investigated using SEM and XRD equipment. SEM analysis revealed that the Ni-B coatings developed six types (pea-like, maize-like, primary nodular, blackberry-like or grapes-like, broccoli-like, and cauliflower-like) of morphological structures depending on the deposition parameters. XRD results also showed that these structures exhibited different levels of amorphous character. The concentration of NaBH4 had the most dominant effect on the morphological and crystallographic development of electroless Ni-B coatings.

  16. Hot-electron-assisted femtochemistry at surfaces: A time-dependent density functional theory approach

    DEFF Research Database (Denmark)

    Gavnholt, Jeppe; Rubio, Angel; Olsen, Thomas

    2009-01-01

    Using time-evolution time-dependent density functional theory (TDDFT) within the adiabatic local-density approximation, we study the interactions between single electrons and molecular resonances at surfaces. Our system is a nitrogen molecule adsorbed on a ruthenium surface. The surface is modeled...... at two levels of approximation, first as a simple external potential and later as a 20-atom cluster. We perform a number of calculations on an electron hitting the adsorbed molecule from inside the surface and establish a picture, where the resonance is being probed by the hot electron. This enables us...

  17. Incident energy dependence of scattering behavior of water molecules on Si (100) and graphite surfaces

    Science.gov (United States)

    Kihara, G.; Kotsubo, Y.; Yoshimoto, Y.; Kinefuchi, I.; Takagi, S.

    2016-11-01

    The interaction between water molecules and solid surfaces has a great impact on water vapor flows in nanostructures. We conduct molecular beam scattering experiments covering the incident energy range corresponding to the thermal energy at room temperature to investigate the scattering behavior of water molecules on silicon and graphite surfaces. The incident energy dependence of the scattering distributions exhibits opposite trends on these surfaces. Molecular dynamics simulations reveal that the difference is caused by the inertia effect of the incident molecules and the surface corrugations.

  18. Atomic layer deposition TiO2 coated porous silicon surface: Structural characterization and morphological features

    International Nuclear Information System (INIS)

    Iatsunskyi, Igor; Jancelewicz, Mariusz; Nowaczyk, Grzegorz; Kempiński, Mateusz; Peplińska, Barbara; Jarek, Marcin; Załęski, Karol; Jurga, Stefan; Smyntyna, Valentyn

    2015-01-01

    TiO 2 thin films were grown on highly-doped p-Si (100) macro- and mesoporous structures by atomic layer deposition (ALD) using TiCl 4 and deionized water as precursors at 300 °C. The crystalline structure, chemical composition, and morphology of the deposited films and initial silicon nanostructures were investigated by scanning electron microscopy, transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy, micro-Raman spectroscopy and X-ray diffraction (XRD). The mean size of TiO 2 crystallites was determined by TEM, XRD and Raman spectroscopy. It was shown that the mean crystallite size and the crystallinity of the TiO 2 are influenced dramatically by the morphology of the porous silicon, with the mesoporous silicon resulting in a much finer grain size and amorphous structure than the macroporous silicon having a partially crystal anatase phase. A simple model of the ALD layer growth inside the pores was presented. - Highlights: • The morphology and chemical composition of TiO 2 and porous Si were established. • The approximate size of TiO 2 nanocrystals was estimated. • The model of the atomic layer deposition coating in the porous Si was presented

  19. Cortical thickness, surface area, and volume of the brain reward system in alcohol dependence: relationships to relapse and extended abstinence.

    Science.gov (United States)

    Durazzo, Timothy C; Tosun, Duygu; Buckley, Shannon; Gazdzinski, Stefan; Mon, Anderson; Fryer, Susanna L; Meyerhoff, Dieter J

    2011-06-01

    At least 60% of those treated for an alcohol use disorder will relapse. Empirical study of the integrity of the brain reward system (BRS) is critical to understanding the mechanisms of relapse as this collection of circuits is implicated in the development and maintenance of all forms of addictive disorders. This study compared thickness, surface area, and volume in neocortical components of the BRS among nonsmoking light-drinking controls (controls), individuals who remained abstinent and those who relapsed after treatment. Seventy-five treatment-seeking alcohol-dependent individuals (abstinent for 7±3 days) and 43 controls completed 1.5T proton magnetic resonance imaging studies. Parcellated morphological data were obtained for following bilateral components of the BRS: rostral and caudal anterior cingulate cortex, insula, medial and lateral orbitofrontal cortex (OFC), rostral and caudal middle and superior frontal gyri, amygdala and hippocampus as well as for 26 other bilateral neocortical regions. Alcohol-dependent participants were followed over 12-months after baseline study and were classified as abstainers (no alcohol consumption; n=24) and relapsers (any alcohol consumption; n=51) at follow-up. Relapsers and abstainers demonstrated lower cortical thickness in the vast majority of BRS regions as well as lower global thickness compared to controls. Relapsers had lower total BRS surface area than both controls and abstainers, but abstainers were not significantly different from controls on any surface area measure. Relapsers demonstrated lower volumes than controls in the majority of regions, while abstainers showed lower volumes than controls in the superior frontal gyrus, insula, amygdala, and hippocampus, bilaterally. Relapsers exhibited smaller volumes than abstainers in the right rostral middle and caudal middle frontal gyri and the lateral OFC, bilaterally. In relapsers, lower baseline volumes and surface areas in multiple regions were associated with

  20. The Size and Shape dependence of the Surface Free Energy of Nanocrystals

    Science.gov (United States)

    Abdul-Hafidh, Esam

    Based on many recent reports, it became possible to control the synthesis of nanomaterials with certain sizes and shapes. A theoretical model to investigate the effect of size and shape on the surface free energy of nanocrystals is worked out in this research. The model is applied to a general shape and size nanocrsytal designated by a shape factor. The model considers all nanocrystals with different morphologies (but with the same shape factor) to be the same. The results were tested for gold and silver. The surface free energy was found to decrease with size for spherical nanocrystals. On the other hand, the surface free energy is enhanced for non-spherical nanocrystals. These findings are in qualitative agreement with previous experimental and theoretical predictions. The results pave the road to manufacture controlled- mechanical properties materials.

  1. Topochip: technology for instructing cell fate and morphology via designed surface topography

    NARCIS (Netherlands)

    Hulshof, G.F.B.

    2016-01-01

    The control of biomaterial surface topography is emerging as a tool to influence cells and tissues. Due to a lack a theoretical framework of the underlying molecular mechanisms, high-throughput screening (HTS) technology is valuable to identify and study bioactive surface topographies. To identify

  2. The Morphology, Dynamics and Potential Hotspots of Land Surface Temperature at a Local Scale in Urban Areas

    Directory of Open Access Journals (Sweden)

    Jiong Wang

    2015-12-01

    Full Text Available Current characterization of the Urban Heat Island (UHI remains insufficient to support the effective mitigation and adaptation of increasing temperatures in urban areas. Planning and design strategies are restricted to the investigation of temperature anomalies at a city scale. By focusing on Land Surface Temperature of Wuhan, China, this research examines the temperature variations locally where mitigation and adaptation would be more feasible. It shows how local temperature anomalies can be identified morphologically. Technically, the MODerate-resolution Imaging Spectroradiometer satellite image products are used. They are first considered as noisy observations of the latent temperature patterns. The continuous latent patterns of the temperature are then recovered from these discrete observations by using the non-parametric Multi-Task Gaussian Process Modeling. The Multi-Scale Shape Index is then applied in the area of focus to extract the local morphological features. A triplet of shape, curvedness and temperature is formed as the criteria to extract local heat islands. The behavior of the local heat islands can thus be quantified morphologically. The places with critical deformations are identified as hotpots. The hotspots with certain yearly behavior are further associated with land surface composition to determine effective mitigation and adaptation strategies. This research can assist in the temperature and planning field on two levels: (1 the local land surface temperature patterns are characterized by decomposing the variations into fundamental deformation modes to allow a process-based understanding of the dynamics; and (2 the characterization at local scale conforms to planning and design conventions where mitigation and adaptation strategies are supposed to be more practical. The weaknesses and limitations of the study are addressed in the closing section.

  3. The effects of processing conditions on the surface morphology and hydrophobicity of polyvinylidene fluoride membranes prepared via vapor-induced phase separation

    Science.gov (United States)

    Peng, Yuelian; Fan, Hongwei; Ge, Ju; Wang, Shaobin; Chen, Ping; Jiang, Qi

    2012-12-01

    The present investigation reveals how the surface morphology and the hydrophobicity of polyvinylidene fluoride (PVDF) membranes, which were prepared via a vapor-induced phase separation method, were affected by the initial PVDF content in the casting solution and the air temperature. The surface morphology was characterized with scanning electron microscopy. A ternary phase diagram of PVDF/N, N-dimethylacetamide/water was constructed to explain the formation mechanism of the different morphologies. The results show that different membrane morphologies and hydrophobicities can be obtained by changing the processing conditions. Low air temperature and high PVDF contents facilitate the crystallization process, resulting in the formation of a porous skin and particle morphology, which increases the hydrophobicity of the surface. High air temperature and low PVDF contents are favorable for the formation of a net-like surface morphology via spinodal decomposition and lead to a superhydrophobic surface. Theoretical calculations were performed to testify that the net-like surface was more favorable for superhydrophobicity than the particle-based surface.

  4. Role of carbon impurities on the surface morphology evolution of tungsten under high dose helium ion irradiation

    International Nuclear Information System (INIS)

    Al-Ajlony, A.; Tripathi, J.K.; Hassanein, A.

    2015-01-01

    The effect of carbon impurities on the surface evolution (e.g., fuzz formation) of tungsten (W) surface during 300 eV He ions irradiation was studied. Several tungsten samples were irradiated by He ion beam with a various carbon ions percentage. The presence of minute carbon contamination within the He ion beam was found to be effective in preventing the fuzz formation. At higher carbon concentration, the W surface was found to be fully covered with a thick graphitic layer on the top of tungsten carbide (WC) layer that cover the sample surface. Lowering the ion beam carbon percentage was effective in a significant reduction in the thickness of the surface graphite layer. Under these conditions the W surface was also found to be immune for the fuzz formation. The effect of W fuzz prevention by the WC formation on the sample surface was more noticeable when the He ion beam had much lower carbon (C) ions content (0.01% C). In this case, the fuzz formation was prevented on the vast majority of the W sample surface, while W fuzz was found in limited and isolated areas. The W surface also shows good resistance to morphology evolution when bombarded by high flux of pure H ions at 900 °C. - Highlights: • Reporting formation of W nanostructure (fuzz) due to low energy He ion beam irradiation. • The effect of adding various percentage of carbon impurity to the He ion beam on the trend of W fuzz formation was studied. • Mitigation of W fuzz formation due to addition of small percentage of carbon to the He ion beam is reported. • The formation of long W nanowires due to He ion beam irradiation mixed with 0.01% carbon ions is reported.

  5. The thumb carpometacarpal joint: curvature morphology of the articulating surfaces, mathematical description and mechanical functioning.

    Science.gov (United States)

    Dathe, Henning; Dumont, Clemens; Perplies, Rainer; Fanghänel, Jochen; Kubein-Meesenburg, Dietmar; Nägerl, Hans; Wachowski, Martin M

    2016-01-01

    The purpose is to present a mathematical model of the function of the thumb carpometacarpal joint (TCMCJ) based on measurements of human joints. In the TCMCJ both articulating surfaces are saddle-shaped. The aim was to geometrically survey the shapes of the articulating surfaces using precise replicas of 28 TCMCJs. None of these 56 articulating surfaces did mathematically extend the differential geometrical neighbourhood around the main saddle point so that each surface could be characterised by three main parameters: the two extreme radii of curvature in the main saddle point and the angle between the saddles' asymptotics (straight lines). The articulating surfaces, when contacting at the respective main saddle points, are incongruent. Hence, the TCMCJ has functionally five kinematical degrees of freedom (DOF); two DOF belong to flexion/extension, two to ab-/adduction. These four DOF are controlled by the muscular apparatus. The fifth DOF, axial rotation, cannot be adjusted but stabilized by the muscular apparatus so that physiologically under compressive load axial rotation does not exceed an angle of approximately ±3°. The TCMCJ can be stimulated by the muscular apparatus to circumduct. The mechanisms are traced back to the curvature incongruity of the saddle surfaces. Hence we mathematically proved that none of the individual saddle surfaces can be described by a quadratic saddle surface as is often assumed in literature. We derived an algebraic formula with which the articulating surfaces in the TCMCJ can be quantitatively described. This formula can be used to shape the articulating surfaces in physiologically equivalent TCMCJ-prostheses.

  6. Morphology dependent change in photovoltage generation using dye-Cu doped ZnO nanoparticle mixed system

    International Nuclear Information System (INIS)

    Bandyopadhyay, Poonam; Nandy, Papiya; Basu, Ruma; Das, Sukhen

    2015-01-01

    The present report deals with the studies on hybrid photoelectrochemical cell containing a commonly used dye, phenosafranine and Cu doped ZnO nanoparticles/nanoflakes for conversion of solar energy to electrical energy. The cell consisting nanoflakes yielded voltage of high magnitude (∼784 mV), good storage duration (∼60 h) and better energy conversion efficiency (3.82%) compared to other similar cells. The particle size and morphology of the nanomaterials were determined with X-ray diffraction and electron microscopy studies. Absorption spectra of the dye-nanomaterial mixed system indicated that the absorbance of dye molecules increased with addition of nanomaterials due to adsorption of dye molecules on the surface of nanomaterials, which facilitated incident photon absorption. Presence of planar lipid membrane hindered the back recombination of photoexcited charges causing radical increase in voltage generation, efficiency and storage duration. - Highlights: • Generation of photovoltage of ∼784 mV by using Cu doped ZnO nanoflakes in PEC cell. • High storage duration of ∼60 h observed using planar lipid membrane. • Energy conversion efficiency of 3.82% obtained

  7. Effect of Irradiation Parameters on Morphology of Polishing DF2 (AISI-O1 Surface by Nd:YAG Laser

    Directory of Open Access Journals (Sweden)

    Wei Guo

    2007-01-01

    Full Text Available Pulse Nd:YAG laser was used to polish DF2 cold work steel. Influence of irradiation parameters on the 3D surface morphology was studied by 3D profilometer, scanning electron microscopy (SEM, and atomic force microscope (AFM. Results among the tests showed when DF2 specimens were irradiated with parameters of (i laser input energy P=1 J, (ii pulse feedrate=300 mm/min, (iii pulse duration (PD =3 milliseconds, and (iv pulse frequency f=20∼25 Hz, laser polishing of DF2 cold work steel seemed to be successful.

  8. The effect of deposition temperature on the surface coverage and morphology of iron-phosphate coatings on low carbon steel

    Energy Technology Data Exchange (ETDEWEB)

    Popic, J.P. [ICTM-Department of Electrochemistry, University of Belgrade, Njegoseva 12, Belgrade (Serbia); Jegdic, B.V., E-mail: borejegdic@yahoo.com [Institute GOSA, Milana Rakica 35, 11000 Belgrade (Serbia); Bajat, J.B.; Veljovic, D. [Faculty of Technology and Metallurgy, University of Belgrade, Karnegijeva 4, P.O. Box 3503, 11120 Belgrade (Serbia); Stevanovic, S.I. [ICTM-Department of Electrochemistry, University of Belgrade, Njegoseva 12, Belgrade (Serbia); Miskovic-Stankovic, V.B. [Faculty of Technology and Metallurgy, University of Belgrade, Karnegijeva 4, P.O. Box 3503, 11120 Belgrade (Serbia)

    2011-10-01

    The influence of deposition temperature and concentration of NaNO{sub 2} in the phosphating bath on the surface morphology and coverage of iron-phosphate coatings on low carbon steel was investigated. The phosphate coatings were chemically deposited on steel from phosphate bath at different temperatures (30-70 deg. C) and with the addition of different amounts of accelerator, NaNO{sub 2} (0.1, 0.5 and 1.0 g dm{sup -3}). The morphology of phosphate coatings was investigated using scanning electron microscopy (SEM) and atomic force microscopy (AFM). The composition of iron-phosphate coatings was determined using energy dispersive X-ray spectroscopy (EDS) and X-ray diffraction (XRD). Surface coverage was evaluated by the voltammetric anodic dissolution (VAD) technique. It was shown that the increase in temperature of the NaNO{sub 2}-free phosphating bath up to 70 deg. C caused an increase in surface coverage. The addition of NaNO{sub 2} in the phosphating bath significantly increased the surface coverage of phosphate coatings deposited at temperatures lower than 50 deg. C. The phosphate crystals were of laminated and needle-like structures for deposits obtained at temperatures lower than 50 deg. C, while at higher temperatures needle-like structure was transformed to laminated structure. The increase in NaNO{sub 2} concentration in the phosphating bath from 0.1 to 1.0 g dm{sup -3} did not significantly increase the surface coverage, but decreased the crystals size, consequently favouring the phosphate nucleation and better packing of the crystals.

  9. Strain-Dependent Solid Surface Stress and the Stiffness of Soft Contacts

    Science.gov (United States)

    Jensen, Katharine E.; Style, Robert W.; Xu, Qin; Dufresne, Eric R.

    2017-10-01

    Surface stresses have recently emerged as a key player in the mechanics of highly compliant solids. The classic theories of contact mechanics describe adhesion with a compliant substrate as a competition between surface energies driving deformation to establish contact and bulk elasticity resisting this. However, it has recently been shown that surface stresses provide an additional restoring force that can compete with and even dominate over elasticity in highly compliant materials, especially when length scales are small compared to the ratio of the surface stress to the elastic modulus, ϒ /E . Here, we investigate experimentally the contribution of surface stresses to the total force of adhesion. We find that the elastic and capillary contributions to the adhesive force are of similar magnitude and that both are required to account for measured adhesive forces between rigid silica spheres and compliant, silicone gels. Notably, the strain dependence of the solid surface stress contributes to the stiffness of soft solid contacts at leading order.

  10. Surface Morphologies of Ti and Ti-Al-V Bombarded by 1.0-MeV Au+ Ions

    Science.gov (United States)

    Garcia, M. A.; Rickards, J.; Cuerno, R.; Trejo-Luna, R.; Cañetas-Ortega, J.; de la Vega, L. R.; Rodríguez-Fernández, L.

    2017-12-01

    Ion implantation is known to enhance the mechanical properties of biomaterials such as, e.g., the wear resistance of orthopedic joints. Increasing the surface area of implants may likewise improve their integration with, e.g., bone tissue, which requires surface features with sizes in the micron range. Ion implantation of biocompatible metals has recently been demonstrated to induce surface ripples with wavelengths of a few microns. However, the physical mechanisms controlling the formation and characteristics of these patterns are yet to be understood. We bombard Ti and Ti-6Al-4V surfaces with 1.0-MeV Au+ ions. Analysis by scanning electron and atomic force microscopies shows the formation of surface ripples with typical dimensions in the micron range, with potential indeed for biomedical applications. Under the present specific experimental conditions, the ripple properties are seen to strongly depend on the fluence of the implanted ions while being weakly dependent on the target material. Moreover, by examining experiments performed for incidence angle values θ =8 ° , 23°, 49°, and 67°, we confirm the existence of a threshold incidence angle for (ripple) pattern formation. Surface indentation is also used to study surface features under additional values of θ , agreeing with our single-angle experiments. All properties of the surface structuring process are very similar to those found in the production of surface nanopatterns under low-energy ion bombardment of semiconductor targets, in which the stopping power is dominated by nuclear contributions, as in our experiments. We consider a continuum model that combines the effects of various physical processes as originally developed in that context, with parameters that we estimate under a binary-collision approximation. Notably, reasonable agreement with our experimental observations is achieved, even under our high-energy conditions. Accordingly, in our system, ripple formation is determined by mass

  11. Revision of Gangesia (Cestoda: Proteocephalidea) in the Indomalayan Region: Morphology, Molecules and Surface Ultrastructure

    Czech Academy of Sciences Publication Activity Database

    Ash, Anirban; Scholz, Tomáš; de Chambrier, A.; Brabec, Jan; Oros, M.; Kar, P. K.; Chavan, S. P.; Mariaux, J.

    2012-01-01

    Roč. 7, č. 10 (2012), e46421 E-ISSN 1932-6203 R&D Projects: GA ČR GA524/08/0885; GA ČR GD206/09/H026; GA ČR GBP505/12/G112 Institutional support: RVO:60077344 Keywords : PHYLOGENETIC TREE SELECTION * APEWORMS PLATYHELMINTHES * SCOLEX MORPHOLOGY * CARYOPHYLLIDEA * EUCESTODA * SILURIFORMES * EVOLUTION Subject RIV: EB - Genetics ; Molecular Biology Impact factor: 3.730, year: 2012 http://www.plosone.org/article/info%3Adoi%2F10.1371%2Fjournal.pone.0046421

  12. USING Hα MORPHOLOGY AND SURFACE BRIGHTNESS FLUCTUATIONS TO AGE-DATE STAR CLUSTERS IN M83

    International Nuclear Information System (INIS)

    Whitmore, Bradley C.; Mutchler, Max; Stankiewicz, Matt; Bond, Howard E.; Chandar, Rupali; Kim, Hwihyun; Kaleida, Catherine; Calzetti, Daniela; Saha, Abhijit; O'Connell, Robert; Balick, Bruce; Carollo, Marcella; Disney, Michael J.; Dopita, Michael A.; Frogel, Jay A.; Hall, Donald N. B.; Holtzman, Jon A.; Kimble, Randy A.; McCarthy, Patrick J.; Paresce, Francesco

    2011-01-01

    We use new WFC3 observations of the nearby grand-design spiral galaxy M83 to develop two independent methods for estimating the ages of young star clusters. The first method uses the physical extent and morphology of Hα emission to estimate the ages of clusters younger than τ ∼ 10 Myr. It is based on the simple premise that the gas in very young (τ V 10 Myr) clusters. A by-product of this study is the identification of 22 'single-star' H II regions in M83, with central stars having ages ∼4 Myr.

  13. Effect of mineral trioxide aggregate surface treatments on morphology and bond strength to composite resin.

    Science.gov (United States)

    Shin, Joo-Hee; Jang, Ji-Hyun; Park, Sang Hyuk; Kim, Euiseong

    2014-08-01

    The aim of this study was to evaluate the micromorphologic changes that accompany different surface treatments on mineral trioxide aggregate (MTA) and their effect on the bond strength to the composite resin with 4 adhesive systems. Three types of MTA cement, ProRoot MTA (WMTA) (Dentsply, Tulsa, OK), MTA Angelus (AMTA) (Angelus, Londrina, PR, Brazil), and Endocem MTA (EMTA) (Maruchi, Wonju, Korea), were prepared and stored for a week to encourage setting. Surface treatment was performed using phosphoric acid or self-etch primer, and an untreated MTA surface was prepared as a control. The surface changes were observed using scanning electron microscopy. MTA surfaces were bonded with 4 adhesive systems, including Scotchbond Multipurpose (3M ESPE, St Paul, MN), Single Bond 2 (3M ESPE), Clearfil SE BOND (Kuraray, Osaka, Japan), and AdheSE One F (Ivoclar Vivadent, Schaan, Liechtenstein), to evaluate the adhesive effectiveness of MTA followed by composite resin restoration. The shear bond strength of the polymerized specimens was tested. For WMTA and AMTA, untreated surfaces showed an irregular crystalline plate with clusters of globular aggregate particles. For EMTA, the untreated surface presented a reticular matrix with acicular crystals. After surface treatment, superficial crystalline structures were eroded regardless of the MTA cement and adhesive system used. WMTA bonded significantly more strongly than AMTA and EMTA, regardless of the adhesive system used. In the WMTA and AMTA groups, AdheSE One F showed the highest bond strength to the composite. For EMTA, no significant differences were found across adhesive systems. Acidic treatment of the MTA surface affected the micromorphology and the bond strength to the composite. Within the limitations of this study, using a 1-step self-etch adhesive system might result in a strong bond to WMTA when the composite resin restoration is required over MTA cement. Copyright © 2014 American Association of Endodontists

  14. Irreversible particle motion in surfactant-laden interfaces due to pressure-dependent surface viscosity

    Science.gov (United States)

    Manikantan, Harishankar; Squires, Todd M.

    2017-09-01

    The surface shear viscosity of an insoluble surfactant monolayer often depends strongly on its surface pressure. Here, we show that a particle moving within a bounded monolayer breaks the kinematic reversibility of low-Reynolds-number flows. The Lorentz reciprocal theorem allows such irreversibilities to be computed without solving the full nonlinear equations, giving the leading-order contribution of surface pressure-dependent surface viscosity. In particular, we show that a disc translating or rotating near an interfacial boundary experiences a force in the direction perpendicular to that boundary. In unbounded monolayers, coupled modes of motion can also lead to non-intuitive trajectories, which we illustrate using an interfacial analogue of the Magnus effect. This perturbative approach can be extended to more complex geometries, and to two-dimensional suspensions more generally.

  15. Obtaining time-dependent multi-dimensional dividing surfaces using Lagrangian descriptors

    Science.gov (United States)

    Feldmaier, Matthias; Junginger, Andrej; Main, Jörg; Wunner, Günter; Hernandez, Rigoberto

    2017-11-01

    Dynamics between reactants and products are often mediated by a rate-determining barrier and an associated dividing surface leading to the transition state theory rate. This framework is challenged when the barrier is time-dependent because its motion can give rise to recrossings across the fixed dividing surface. A non-recrossing time-dependent dividing surface can nevertheless be attached to the TS trajectory resulting in recrossing-free dynamics. We extend the formalism-constructed using Lagrangian Descriptors-to systems with additional bath degrees of freedom. The propagation of reactant ensembles provides a numerical demonstration that our dividing surface is recrossing-free and leads to exact TST rates.

  16. Temperature-dependent surface density of alkylthiol monolayers on gold nanocrystals

    Science.gov (United States)

    Liu, Xuepeng; Lu, Pin; Zhai, Hua; Wu, Yucheng

    2018-03-01

    Atomistic molecular dynamics (MD) simulations are performed to study the surface density of passivating monolayers of alkylthiol chains on gold nanocrystals at temperatures ranging from 1 to 800 K. The results show that the surface density of alkylthiol monolayer reaches a maximum value at near room temperature (200-300 K), while significantly decreases with increasing temperature in the higher temperature region (> 300 {{K}}), and slightly decreases with decreasing temperature at low temperature (< 200 {{K}}). We find that the temperature dependence of surface ligand density in the higher temperature region is attributed to the substantial ligand desorption induced by the thermal fluctuation, while that at low temperature results from the reduction in entropy caused by the change in the ordering of passivating monolayer. These results are expected helpful to understand the temperature-dependent surface coverage of gold nanocrystals.

  17. Marine Phages As Tracers: Effects of Size, Morphology, and Physico-Chemical Surface Properties on Transport in a Porous Medium.

    Science.gov (United States)

    Ghanem, Nawras; Kiesel, Bärbel; Kallies, René; Harms, Hauke; Chatzinotas, Antonis; Wick, Lukas Y

    2016-12-06

    Although several studies examined the transport of viruses in terrestrial systems only few studies exist on the use of marine phages (i.e., nonterrestrial viruses infecting marine host bacteria) as sensitively detectable microbial tracers for subsurface colloid transport and water flow. Here, we systematically quantified and compared for the first time the effects of size, morphology and physicochemical surface properties of six marine phages and two coliphages (MS2, T4) on transport in sand-filled percolated columns. Phage-sand interactions were described by colloidal filtration theory and the extended Derjaguin-Landau-Verwey-Overbeek approach (XDLVO), respectively. The phages belonged to different families and comprised four phages never used in transport studies (i.e., PSA-HM1, PSA-HP1, PSA-HS2, and H3/49). Phage transport was influenced by size, morphology and hydrophobicity in an approximate order of size > hydrophobicity ≥ morphology. Two phages PSA-HP1, PSA-HS2 (Podoviridae and Siphoviridae) exhibited similar mass recovery as commonly used coliphage MS2 and were 7-fold better transported than known marine phage vB_PSPS-H40/1. Differing properties of the marine phages may be used to trace transport of indigenous viruses, natural colloids or anthropogenic nanomaterials and, hence, contribute to better risk analysis. Our results underpin the potential role of marine phages as microbial tracer for transport of colloidal particles and water flow.

  18. Mucosal surface morphology and histological changes in the duodenum of the rat following administration of cysteamine

    DEFF Research Database (Denmark)

    Poulsen, Steen Seier; Szabo, S

    1977-01-01

    Acute duodenal ulcer can be produced in the rat by subcutaneous or oral administration of cysteamine. Development of this ulcer on the intestinal mucosal surface was followed from precursory stages to perforation using low power semimacroscopical and conventional histological techniques. The proc......Acute duodenal ulcer can be produced in the rat by subcutaneous or oral administration of cysteamine. Development of this ulcer on the intestinal mucosal surface was followed from precursory stages to perforation using low power semimacroscopical and conventional histological techniques....... The process started in the epithelium of the apical parts of the villi where segments of surface epithelial cells exfoliated and the lamina propria seemed to retract. As the process continued the villi gradually became lower eventually forming an avillous surface. Subsequently defects in the epithelium...

  19. Analysis of Surface and Subsurface Damage Morphology in Rotary Ultrasonic Machining of BK7 Glass

    Science.gov (United States)

    Hong-xiang, Wang; Chu, Wang; Jun-liang, Liu; Shi, Gao; Wen-Jie, Zhai

    2017-11-01

    This paper investigates the formation process of surface/subsurface damage in the rotary ultrasonic machining of BK7 glass. The results show that during the milling using the end face of the tool, the cutting depth and the residual height between the abrasive grains constantly change with the high-frequency vibration, generating lots of cracks on both sides of the scratches. The high-frequency vibration accelerates the chips falling from the surface, so that the chips and thermal damage are reduced, causing the grinding surface quality better. A plastic deformation area is formed during the grinding, due to the non-uniform cutting force on the material surface, and the residual stress is produced in the deformation area, inducing the median/lateral cracks.

  20. Influence of ZnSe:Te substrate's surface morphology on their optical properties

    Directory of Open Access Journals (Sweden)

    Makhniy V. P.

    2016-12-01

    Full Text Available The authors have experimentally established, that etching of ZnSe:Te substrates in CrO3:HCl=2:1 and H2SO4:H2O2=3:1 solutions leads to formation of mirror and matte surfaces. Analysis of the topogram obtained by an atomic power microscope showed that matte surface is a set of equally oriented pyramids with basis size 2-5 μm and each of them is association of nanopyramids with 10-100 nm lateral size. In such samples wide photoluminescence band at 2.7-3.8 eV is a result of dimensional quantization in smaller nanocrystals. The latter also causes an observed decrease of transmission coefficient of substrates with matte surface in comparison to those with mirror surface owing to increase of light scattering processes.

  1. Cell-surface metalloprotease ADAM12 is internalized by a clathrin- and Grb2-dependent mechanism

    DEFF Research Database (Denmark)

    Hansen, Dorte Stautz; Leyme, Anthony; Grandal, Michael Vibo

    2012-01-01

    ADAM12 (A Disintegrin And Metalloprotease 12), a member of the ADAMs family of transmembrane proteins, is involved in ectodomain shedding, cell-adhesion and signaling, with important implications in cancer. Therefore, mechanisms that regulate the levels and activity of ADAM12 at the cell...... that regulates ADAM cell surface levels and show that ADAM12 internalization involves the clathrin-dependent pathway and Grb2.......-surface are possibly crucial in these contexts. We here investigated internalization and subsequent recycling or degradation of ADAM12 as a potentially important regulatory mechanism. Our results show that ADAM12 is constitutively internalized primarily via the clathrin-dependent pathway and is subsequently detected...

  2. Temperature Dependence of Arn + Cluster Backscattering from Polymer Surfaces: a New Method to Determine the Surface Glass Transition Temperature

    Science.gov (United States)

    Poleunis, Claude; Cristaudo, Vanina; Delcorte, Arnaud

    2018-01-01

    In this work, time-of-flight secondary ion mass spectrometry (ToF-SIMS) was used to study the intensity variations of the backscattered Arn + clusters as a function of temperature for several amorphous polymer surfaces (polyolefins, polystyrene, and polymethyl methacrylate). For all these investigated polymers, our results show a transition of the ratio Ar2 +/(Ar2 + + Ar3 +) when the temperature is scanned from -120 °C to +125 °C (the exact limits depend on the studied polymer). This transition generally spans over a few tens of degrees and the temperature of the inflection point of each curve is always lower than the bulk glass transition temperature (Tg) reported for the considered polymer. Due to the surface sensitivity of the cluster backscattering process (several nanometers), the presented analysis could provide a new method to specifically evaluate a surface transition temperature of polymers, with the same lateral resolution as the gas cluster beam. [Figure not available: see fulltext.

  3. Temperature Dependence of Arn+ Cluster Backscattering from Polymer Surfaces: a New Method to Determine the Surface Glass Transition Temperature.

    Science.gov (United States)

    Poleunis, Claude; Cristaudo, Vanina; Delcorte, Arnaud

    2018-01-01

    In this work, time-of-flight secondary ion mass spectrometry (ToF-SIMS) was used to study the intensity variations of the backscattered Ar n + clusters as a function of temperature for several amorphous polymer surfaces (polyolefins, polystyrene, and polymethyl methacrylate). For all these investigated polymers, our results show a transition of the ratio Ar 2 + /(Ar 2 + + Ar 3 + ) when the temperature is scanned from -120 °C to +125 °C (the exact limits depend on the studied polymer). This transition generally spans over a few tens of degrees and the temperature of the inflection point of each curve is always lower than the bulk glass transition temperature (T g ) reported for the considered polymer. Due to the surface sensitivity of the cluster backscattering process (several nanometers), the presented analysis could provide a new method to specifically evaluate a surface transition temperature of polymers, with the same lateral resolution as the gas cluster beam. Graphical abstract ᅟ.

  4. Synthesis and processing of ELISA polymer substitute: The influence of surface chemistry and morphology on detection sensitivity

    Science.gov (United States)

    Hosseini, Samira; Ibrahim, Fatimah; Djordjevic, Ivan; Rothan, Hussin A.; Yusof, Rohana; van der Marel, Cees; Koole, Leo H.

    2014-10-01

    Despite the known drawbacks of enzyme-linked immunosorbent assay (ELISA), one of the deficiencies that have relatively been ignored is the performance of ELISA substrate itself. Polystyrene (PS), as the cost effective material of choice for mass production of ELISA well-plates, has shown obvious lacks of suitable physical and chemical properties for protein attachment. The general concept of this work was to develop a potential substrate that can be suggested as a material of choice for production of a new generation of ELISA analytical kits. Spin-coated thin films of polymethyl methacrylate-co-methacrylic acid (PMMA-co-MAA) on silicon surfaces were designed and processed for detection of dengue virus. Coated surfaces of different molar ratios have been investigated as carboxyl-functionalized layers for obtaining platform for biomolecule immobilization with high level of protein activity. To improve the sensitivity of detection, we have used amine functional "spacers", hexamethylenediamine (HMDA) and polyethyleneimine (PEI), which were covalently bonded to the surfaces of PMMA-co-MAA coatings. Results demonstrate that the variation of surface concentration of carboxyl groups of PMMA-co-MAA can be used to control the amine surface concentration after carbodiimide coupling with HMDA and PEI spacers. The presence of amine spacers increases hydrophilicity of the coatings and significantly impacts the polymer surface morphology. In particular, protein immobilization via amine-bearing spacers has been achieved in two effective steps: (1) carbodiimide bonding between amine spacer molecules and PMMA-co-MAA polymer coatings; and (2) covalent immobilization of antibody via glutaraldehyde reaction with amine groups from amine-treated surfaces. The application of PEI spacer in comparison to HMDA has shown much higher intensity of detection signal in ELISA experiment, indicating better immobilization efficiency and preservation of antibody activity upon attachment to the

  5. In vitro effect of meconium on the physical surface properties and morphology of exogenous pulmonary surfactant.

    Science.gov (United States)

    Park, K. H.; Bae, C. W.; Chung, S. J.

    1996-01-01

    The pathophysiology of meconium aspiration syndrome(MAS) is related to mechanical obstruction of the airways and to chemical pneumonitis. Meconium is also suggested to cause functional deterioration of pulmonary surfactant. Recent studies have reported that meconium inhibits the physical surface properties of pulmonary surfactant, and that administration of exogenous surfactant may provide therapeutic benefits in animal models or infants with respiratory distress due to MAS. To assess the effects of meconium on physical surface properties, especially the changes on the air-liquid interface and hypophase of pulmonary surfactant in vitro, we studied the following findings; a) the surface spreading rate(SSR) and the surface adsorption rate(SAR), b) the viscosity, c) the electron microscopic changes, on a series of mixtures with various concentrations of lyophilized human meconium and Surfactant-TA(SurfactenTM). The human meconium has significantly increased the surface tension of SSR and the viscosity of pulmonary surfactant, but had decreased the surface pressure of SAR of surfactant, and changed the electron microscopic findings of surfactant. We have concluded that these findings support the concept that meconium-induced surfactant dysfunction may play a role in the pathophysiology of MAS. PMID:8934399

  6. Infrared optical responses of wurtzite In{sub x}Ga{sub 1−x}N thin films with porous surface morphology

    Energy Technology Data Exchange (ETDEWEB)

    Yew, P., E-mail: paulinevcu@hotmail.com [Institute of Nano-Optoelectronics Research and Technology (INOR), Universiti Sains Malaysia, 11800 Minden, Penang (Malaysia); School of Physics, Universiti Sains Malaysia, 11800 Minden, Penang (Malaysia); Lee, S.C. [School of Physics, Universiti Sains Malaysia, 11800 Minden, Penang (Malaysia); Centre of Excellence for Pre-University Studies, INTI International College Penang, Laureate International University, 1-Z, Lebuh Bukit Jambul, 11900 Penang (Malaysia); Ng, S.S. [Institute of Nano-Optoelectronics Research and Technology (INOR), Universiti Sains Malaysia, 11800 Minden, Penang (Malaysia); Hassan, H. Abu [School of Physics, Universiti Sains Malaysia, 11800 Minden, Penang (Malaysia); Chen, W.L. [Department of Electronic Engineering, National Changhua University of Education, 500, Taiwan, ROC (China); Osipowicz, T.; Ren, M.Q. [Centre for Ion Beam Applications (CIBA), Department of Physics, National University of Singapore, Singapore 119260 (Singapore)

    2016-03-31

    Room temperature infrared (IR) optical responses of wurtzite indium gallium nitride (In{sub x}Ga{sub 1−x}N) in the composition range of 0.174 ≤ x ≤ 0.883 were investigated by the polarized IR reflectance spectroscopy. Analyses of the amplitudes of oscillation fringes in the non-reststrahlen region revealed that the high frequency dielectric constants of the samples were unusually smaller than the values predicted from the Clausius–Mossotti relation. This odd behavior was attributed to the porous surface morphology of the In{sub x}Ga{sub 1−x}N samples. The E{sub 1} optical phonon modes of the In{sub x}Ga{sub 1−x}N were deduced from the composition dependent reststrahlen features. The obtained values were compared to those calculated through the modified random element iso-displacement (MREI) model. The deviation between the measured data and the MREI model prediction were explained in detail from the aspects of strain, thermal expansion and anharmonic phonon-coupling. Finally, it was found that the large discrepancy of the E{sub 1}(LO) mode is mainly attributed to the effects of the longitudinal phonon–plasmon coupling. - Highlights: • Composition dependence of E{sub 1} modes of In{sub x}Ga{sub 1−x}N alloys (x = 0.174 to 0.883) • Dependence of porous morphology on infrared (IR) optical properties • Longitudinal phonon–plasmon coupling obscures determination of E{sub 1}(LO) mode.

  7. The Wafer and Diffusion Lot Dependence of Surface Effects Resulting from Ionizing Radiation,

    Science.gov (United States)

    An investigation of the wafer and diffusion lot dependence of surface effects resulting from ionizing radiation was conducted by irradiating samples...of transistors. The transistors were selected by the wafer and diffusion lot from which they were produced. Both NPN and PNP transistors were...the diffusion lot . With the PNP’s which were not effected to the same extent as the NPN’s the dependence on the wafer or diffusion lot was not

  8. Surface morphology and dislocation characteristics near the surface of 4H-SiC wafer using multi-directional scanning transmission electron microscopy.

    Science.gov (United States)

    Sato, Takahiro; Orai, Yoshihisa; Suzuki, Yuya; Ito, Hiroyuki; Isshiki, Toshiyuki; Fukui, Munetoshi; Nakamura, Kuniyasu; Schamp, C T

    2017-10-01

    To improve the reliability of silicon carbide (SiC) electronic power devices, the characteristics of various kinds of crystal defects should be precisely understood. Of particular importance is understanding the correlation between the surface morphology and the near surface dislocations. In order to analyze the dislocations near the surface of 4H-SiC wafers, a dislocation analysis protocol has been developed. This protocol consists of the following process: (1) inspection of surface defects using low energy scanning electron microscopy (LESEM), (2) identification of small and shallow etch pits using KOH low temperature etching, (3) classification of etch pits using LESEM, (4) specimen preparation of several hundred nanometer thick sample using the in-situ focused ion beam micro-sampling® technique, (5) crystallographic analysis using the selected diffraction mode of the scanning transmission electron microscope (STEM), and (6) determination of the Burgers vector using multi-directional STEM (MD-STEM). The results show a correlation between the triangular terrace shaped surface defects and an hexagonal etch pit arising from threading dislocations, linear shaped surface defects and elliptical shaped etch pits arising from basal plane dislocations. Through the observation of the sample from two orthogonal directions via the MD-STEM technique, a basal plane dislocation is found to dissociate into an extended dislocation bound by two partial dislocations. A protocol developed and presented in this paper enables one to correlate near surface defects of a 4H-SiC wafer with the root cause dislocations giving rise to those surface defects. © The Author 2017. Published by Oxford University Press on behalf of The Japanese Society of Microscopy. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  9. Multidendritic sensory neurons in the adult Drosophila abdomen: origins, dendritic morphology, and segment- and age-dependent programmed cell death

    Directory of Open Access Journals (Sweden)

    Sugimura Kaoru

    2009-10-01

    Full Text Available Abstract Background For the establishment of functional neural circuits that support a wide range of animal behaviors, initial circuits formed in early development have to be reorganized. One way to achieve this is local remodeling of the circuitry hardwiring. To genetically investigate the underlying mechanisms of this remodeling, one model system employs a major group of Drosophila multidendritic sensory neurons - the dendritic arborization (da neurons - which exhibit dramatic dendritic pruning and subsequent growth during metamorphosis. The 15 da neurons are identified in each larval abdominal hemisegment and are classified into four categories - classes I to IV - in order of increasing size of their receptive fields and/or arbor complexity at the mature larval stage. Our knowledge regarding the anatomy and developmental basis of adult da neurons is still fragmentary. Results We identified multidendritic neurons in the adult Drosophila abdomen, visualized the dendritic arbors of the individual neurons, and traced the origins of those cells back to the larval stage. There were six da neurons in abdominal hemisegment 3 or 4 (A3/4 of the pharate adult and the adult just after eclosion, five of which were persistent larval da neurons. We quantitatively analyzed dendritic arbors of three of the six adult neurons and examined expression in the pharate adult of key transcription factors that result in the larval class-selective dendritic morphologies. The 'baseline design' of A3/4 in the adult was further modified in a segment-dependent and age-dependent manner. One of our notable findings is that a larval class I neuron, ddaE, completed dendritic remodeling in A2 to A4 and then underwent caspase-dependent cell death within 1 week after eclosion, while homologous neurons in A5 and in more posterior segments degenerated at pupal stages. Another finding is that the dendritic arbor of a class IV neuron, v'ada, was immediately reshaped during post

  10. Effect of Water Vapor and Surface Morphology on the Low Temperature Response of Metal Oxide Semiconductor Gas Sensors.

    Science.gov (United States)

    Maier, Konrad; Helwig, Andreas; Müller, Gerhard; Hille, Pascal; Eickhoff, Martin

    2015-09-23

    In this work the low temperature response of metal oxide semiconductor gas sensors is analyzed. Important characteristics of this low-temperature response are a pronounced selectivity to acid- and base-forming gases and a large disparity of response and recovery time constants which often leads to an integrator-type of gas response. We show that this kind of sensor performance is related to the trend of semiconductor gas sensors to adsorb water vapor in multi-layer form and that this ability is sensitively influenced by the surface morphology. In particular we show that surface roughness in the nanometer range enhances desorption of water from multi-layer adsorbates, enabling them to respond more swiftly to changes in the ambient humidity. Further experiments reveal that reactive gases, such as NO₂ and NH₃, which are easily absorbed in the water adsorbate layers, are more easily exchanged across the liquid/air interface when the humidity in the ambient air is high.

  11. Morphology of ablation craters generated by ultra-short laser pulses in dentin surfaces: AFM and ESEM evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Daskalova, A., E-mail: a_daskalova@code.bg [Institute of Electronics, Bulgarian Academy of Sciences, 72, Tsarigradsko Chaussee Blvd., 1784 Sofia (Bulgaria); Bashir, S.; Husinsky, W. [IAP, Vienna University of Technology, Wiedner Hauptstrasse 8-10, 1040 Vienna (Austria)

    2010-11-15

    In this study, the surface morphology and structure of dentin after ablation by ultra-short pulses were evaluated using environmental scanning electron microscopy (ESEM) and atomic force microscopy (AFM). The dentin specimens examined were irradiated by a chirped-pulse-amplification (CPA) Ti:sapphire laser (800 nm) and the optimal conditions for producing various nanostructures were determined. Based on the ESEM results, it was possible to identify an energy density range as the ablation threshold for dentin. The laser-induced damage was characterized over the fluence range 1.3-2.1 J/cm{sup 2}. The results demonstrate that by selecting suitable parameters one can obtain efficient dentin surface preparation without evidence of thermal damage, i.e., with minimized heat affected zones and reduced collateral damage, the latter being normally characterized by formation of microcracks, grain growth and recrystallization in the heat affected zones.

  12. Tailoring the morphology and electrocatalytic properties of electrochemically formed Ag/TiO2 composite deposits on titanium surfaces

    Directory of Open Access Journals (Sweden)

    S. V. MENTUS

    2007-12-01

    Full Text Available Three different forms of Ag/TiO2 composite layers, which have whisker-, dot- and island-like distribution of silver were obtained on a mechanically polished titanium surface by adjusting the conditions of silver deposition from an aqueous AgNO3 solution. The deposit morphology was the result of both the program of electrode polarization and the template action of the simultaneously formed TiO2 layer. The catalytic activity of the composite layers toward the oxygen reduction reaction was studied in aqueous 0.1 M NaOH solutions and found to be a function of both the surface loading of silver and the type of silver distribution within the Ag/TiO2 composite layers. The reaction path of oxygen reduction on the composite layers was found to be always a 4e- one, characteristic otherwise of polycrystalline silver electrodes.

  13. A comparative study on surface morphological investigations of ferric oxide for LPG and opto-electronic humidity sensors

    Science.gov (United States)

    Singh, Satyendra; Verma, Nidhi; Yadav, B. C.; Prakash, Rajiv

    2012-09-01

    In the present work nanostructured ferric oxides were synthesized via hydroxide precipitation method without using any surfactant and size selection medium. The surface morphologies and structure of samples were analyzed by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray diffraction (XRD). The structural analysis confirmed the formation of Fe2O3 with α-phase and rhombohedral structure. Optical and thermal properties were investigated by using UV-visible absorption spectroscopy and differential scanning calorimetry (DSC) techniques. Pelletizations of materials were done using hydraulic press and these pellets were investigated with the exposition of liquefied petroleum gas. Variations in resistance of the pellet with time for different concentrations of LPG were recorded at room temperature (27 °C). The maximum value of average sensitivity was found ˜5 for 5 vol.% of LPG. Our results show that the LPG sensing behavior was inspired by the different kinds of surface morphologies of Fe2O3 and inferred that the spherical porous nanoparticles synthesized via hydroxide precipitation process (S-3) had best response to LPG.

  14. Modeling Bone Surface Morphology: A Fully Quantitative Method for Age-at-Death Estimation Using the Pubic Symphysis.

    Science.gov (United States)

    Slice, Dennis E; Algee-Hewitt, Bridget F B

    2015-07-01

    The pubic symphysis is widely used in age estimation for the adult skeleton. Standard practice requires the visual comparison of surface morphology against criteria representing predefined phases and the estimation of case-specific age from an age range associated with the chosen phase. Known problems of method and observer error necessitate alternative tools to quantify age-related change in pubic morphology. This paper presents an objective, fully quantitative method for estimating age-at-death from the skeleton, which exploits a variance-based score of surface complexity computed from vertices obtained from a scanner sampling the pubic symphysis. For laser scans from 41 modern American male skeletons, this method produces results that are significantly associated with known age-at-death (RMSE = 17.15 years). Chronological age is predicted, therefore, equally well, if not, better, with this robust, objective, and fully quantitative method than with prevailing phase-aging systems. This method contributes to forensic casework by responding to medico-legal expectations for evidence standards. © 2015 American Academy of Forensic Sciences.

  15. Fractal analysis as a potential tool for surface morphology of thin films

    Science.gov (United States)

    Soumya, S.; Swapna, M. S.; Raj, Vimal; Mahadevan Pillai, V. P.; Sankararaman, S.

    2017-12-01

    Fractal geometry developed by Mandelbrot has emerged as a potential tool for analyzing complex systems in the diversified fields of science, social science, and technology. Self-similar objects having the same details in different scales are referred to as fractals and are analyzed using the mathematics of non-Euclidean geometry. The present work is an attempt to correlate fractal dimension for surface characterization by Atomic Force Microscopy (AFM). Taking the AFM images of zinc sulphide (ZnS) thin films prepared by pulsed laser deposition (PLD) technique, under different annealing temperatures, the effect of annealing temperature and surface roughness on fractal dimension is studied. The annealing temperature and surface roughness show a strong correlation with fractal dimension. From the regression equation set, the surface roughness at a given annealing temperature can be calculated from the fractal dimension. The AFM images are processed using Photoshop and fractal dimension is calculated by box-counting method. The fractal dimension decreases from 1.986 to 1.633 while the surface roughness increases from 1.110 to 3.427, for a change of annealing temperature 30 ° C to 600 ° C. The images are also analyzed by power spectrum method to find the fractal dimension. The study reveals that the box-counting method gives better results compared to the power spectrum method.

  16. Is Morphological Priming Stronger for Transparent than Opaque Words? It Depends on Individual Differences in Spelling and Vocabulary

    Science.gov (United States)

    Andrews, Sally; Lo, Steson

    2013-01-01

    This experiment used the masked priming lexical decision task to address previous contradictory evidence about the relative strength of priming for (i) transparent pairs (e.g., "worker" "WORK") which are morphologically and semantically related; (ii) opaque pairs (e.g., "corner" "CORN") which appear to be morphological relatives but are not…

  17. NIZAMS: THE HIDDEN SYNTAX UNDER THE SURFACE. URBAN MORPHOLOGY IN TRADITIONAL ISLAMIC CITIES

    Directory of Open Access Journals (Sweden)

    Somaiyeh Falahat

    2012-03-01

    Full Text Available The reasons behind the urban form of traditional ‘Islamic cities’ are still disputable themes among authors. As a step forward, the city should be observed by taking into consideration the indigenous structures and concepts. This article, after reviewing the earlier ideas and efforts in this regard, suggests that the city is the result of interaction of various Niams and the major reason underlying the urban morphology is the simultaneous presence of these Niams and the fact that their hierarchy of importance was flat and horizontal. It defines the Nizams as interlinked frameworks including various dimensions which make the syntax of the city’s order

  18. Potential dependence of surface crystal structure of iron passive films in borate buffer solution

    International Nuclear Information System (INIS)

    Deng, Huihua; Nanjo, Hiroshi; Qian, Pu; Santosa, Arifin; Ishikawa, Ikuo; Kurata, Yoshiaki

    2007-01-01

    The effect of passivation potential on surface crystal structure, apparent thickness and passivity of oxide films formed on pure iron prepared by plasma sputter deposition was investigated. The crystallinity was improved with passivation potential and the width of atomically flat terraces was expanded to 6 nm when passivating at 750 mV for 15 min, as observed by ex situ scanning tunneling microscopy (STM) after aging in air (<30% RH). Apparent thickness and passivity are linearly dependent on passivation potential. The former weakly depends on passivation duration, the latter strongly depends on passivation duration. This is well explained by the correlation between crystal structure and passivity

  19. The relationship between the incisor position and lingual surface morphology in normal occlusion.

    Science.gov (United States)

    Hasegawa, Yuh; Ezura, Akira; Nomintsetseg, Batbayar

    2017-01-01

    This study aimed to investigate the relationship between the morphological characteristics of maxillary incisors and the anterior occlusion. The study materials comprised dental casts and lateral cephalograms of 26 modern Mongolian females with Angle Class I normal occlusion (mean age, 21 years 5 months). Computed tomography (CT) images of the dental casts were taken with an X-ray micro-CT system (SMX-100CT, Shimadzu, Kyoto Japan). The thickness of the marginal ridges and incisal edges, and the overjet and overbite, was measured on the three-dimensional images of the dental casts. On the lateral cephalogram, maxillary incisor to sella-nasion plane angle (U1 to SN angle), maxillary incisor to nasion-point A plane distance (U1 to NA distance), mandibular incisor to nasion-point B plane distance (L1 to NB distance), incisor mandibular plane angle, and interincisal angle were measured by tracing the left incisors of the maxilla and mandible. Spearman's single rank correlation coefficients were used to investigate any correlation between measurement items for each maxillary incisor. The thickness of the marginal ridges and incisal edges was positively correlated with the overbite. The thickness of the incisal edges was positively correlated with the irregularity index of the maxilla. There were significant negative correlations between overbite and U1 to SN angle, U1 to NA distance, and L1 to NB distance. Significant positive correlations were noted between the overbite and the overjet. In conclusion, there was no strong relationship between the morphological characteristics of maxillary incisors and the anterior occlusion.

  20. Molecular-dynamics theory of the temperature-dependent surface phonons of W(001)

    International Nuclear Information System (INIS)

    Wang, C.Z.; Fasolino, A.; Tosatti, E.

    1987-04-01

    We study the temperature-dependent zone-boundary surface phonons across the c(2x2)→1x1 reconstruction phase transition of the clean W(001) surface. Velocity-velocity correlations and hence the phonon spectral densities are calculated by molecular dynamics for the surface atoms of a finite thickness (001) slab, with interatomic potentials established in a previous study of the surface statics. Our calculated k = (1/2,1/2)(2π/a) surface phonon are dominated by three main low-frequency modes. Of these, the longitudinal and the shear horizontal are reconstruction-related and display critical broadening and softening at the phase transition, while the third, the shear vertical, is basically unaffected. The reconstruction phase mode, shear horizontal, appears to be responsible for the phase fluctuations which destroy long-range order at the transition. (author). 30 refs, 12 figs

  1. In vitro sliding-driven morphological changes in representative esthetic NiTi archwire surfaces.

    Science.gov (United States)

    Choi, Samjin; Park, Dong-Jin; Kim, Kyung-A; Park, Ki-Ho; Park, Hun-Kuk; Park, Young-Guk

    2015-10-01

    This study investigated the effects of sliding on the ultrastructure of three representative esthetic superelastic 0.014 inch nickel-titanium (NiTi) archwires. Atomic force microscopy, scanning electron microscopy, and light microscopy were used to estimate the surface roughness of archwires and bracket systems. Energy-dispersive X-ray spectroscopy was used to estimate the molecular differences between coated and uncoated areas. A combination of four different types of 0.014 inch metallic wires and two different types of 0.022 inch × 0.028 inch conventional brackets were evaluated by in vitro sliding tests using a novel self-made tensile-strength tester with a miniature load cell and syringe pump. The NiTi wires included an uncoated NiTi archwire (CO group), epoxy resin-coated NiTi archwire (ER group), Teflon(®) -coated NiTi archwire (TF group), and Ag/biopolymer-coated NiTi archwire (AG group). The brackets included contained stainless steel (SS) and ceramic (CE) brackets. Both ER and TF wire groups exhibited less surface roughness than CO wire groups. The AG group showed the highest surface roughness compared with the others because of its silver particles (Ptest). In vitro sliding tests led to a significant increase (P test) in the surface roughness of all 0.014 inch NiTi wires regardless of bracket type. The wire groups combined with SS brackets were rougher than those of CE brackets regardless of the coating materials because of exfoliation of the coating materials. The TF-SS group showed the highest increase (fivefold) in surface roughness compared to the others, while the ER groups showed the lowest increase (1.4-fold) in surface roughness compared with the others (P test). The results suggested that the sliding-driven surface roughness of superelastic NiTi archwires is directly affected by coating materials. Although the efficiency of orthodontic treatment was affected by various factors, epoxy resin-coated archwires were best for both esthetics and

  2. Dependence of the runaway greenhouse threshold on the surface water distribution for Earth-like planets

    Science.gov (United States)

    Kodama, T.; Nitta, A.; Genda, H.; Oishi, R.; Abe-Ouchi, A.; Abe, Y.

    2017-12-01

    Liquid water is one of the important materials that affect the climate and habitability on a terrestrial planet. Liquid water entirely vaporizes when planets receive insolation above a certain critical value, which is called the runaway greenhouse threshold. This threshold forms the inner most limit of the habitable zone. In general, it is assumed that an Earth-like planet with oceans is a potentially habitable planet. Such a planet is implicitly assumed to be a planet whose surface is covered with oceans. Thus, most of previous studies estimated the runaway greenhouse threshold for such planets. Abe et al. (2011) suggest that the runaway greenhouse threshold significantly depends on the distribution of water on the surface. The distribution of the surface water is determined by the surface topography, the surface water flow and the transport of water vapor in the atmosphere. Here, we investigate the effects of the distribution of surface water on the runaway greenhouse threshold for Earth-sized planets using a three-dimensional dynamic atmosphere model. We recognized two climate regimes: the land planet regime, which has dry low latitude and wet high latitude regions, and the aqua planet regime, which is globally wet. We showed that each regime is controlled by the width of the Hadley circulation, the amount of surface water, and the planetary topography. We found that the runaway greenhouse threshold continuously varies with the surface water distribution from about 130% (an aqua planet) to 180% (the extreme case of a land planet) of the present insolation at Earth's orbit. Our results indicate that the inner edge of the habitable zone is not a single sharp boundary, but a border whose location varies depending on planetary surface condition, such as the amount of surface water.

  3. Dependence of the textural properties and surface species of ZnO ...

    Indian Academy of Sciences (India)

    Home; Journals; Bulletin of Materials Science; Volume 40; Issue 3. Dependence of the textural properties and surface species of ZnO photocatalytic materials on the type of precipitating agent used in the hydrothermal synthesis. I STAMBOLOVA V BLASKOV D STOYANOVA I AVRAMOVA L DIMITROV K MILENOVA K ...

  4. Surface-Dependent Transitions during Self-Assembly of Phospholipid Membranes on Mica, Silica, and Glass

    Czech Academy of Sciences Publication Activity Database

    Beneš, Martin; Billy, D.; Benda, Aleš; Speijer, H.; Hof, Martin; Hermens, W. T.

    2004-01-01

    Roč. 20, č. 23 (2004), s. 10129-10137 ISSN 0743-7463 R&D Projects: GA MŠk LN00A032 Institutional research plan: CEZ:AV0Z4040901 Keywords : silica and glass * phospholipid * surface-dependent Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 3.295, year: 2004

  5. A method for calculating the time-dependent surface temperature of a cylinder containing radioactive waste

    International Nuclear Information System (INIS)

    Fynbo, P.B.

    1981-02-01

    A method is described by which the surface temperature of a steel cylinder containing radioactive waste can be calculated. The method assumes a time-dependent continuous line source in cylindrical symmetry and it applies Laplace transformation. The resultant laplace transform is approximated and then inverted (by convolution). The method is computationally fast and future generalisations to similar problems are suggested. (author)

  6. Hyaluronic acid-coated chitosan nanoparticles: molecular weight-dependent effects on morphology and hyaluronic acid presentation.

    Science.gov (United States)

    Almalik, Abdulaziz; Donno, Roberto; Cadman, Christopher J; Cellesi, Francesco; Day, Philip J; Tirelli, Nicola

    2013-12-28

    Chitosan nanoparticles are popular carriers for the delivery of macromolecular payloads, e.g. nucleic acids. In this study, nanoparticles were prepared via complexation with triphosphate (TPP) anions and were successively coated with hyaluronic acid (HA). Key variables of the preparative process (e.g. chitosan and HA molecular weight) were optimised in view of the maximisation of loading with DNA, of the Zeta potential and of the dimensional stability, and the resulting particles showed excellent storage stability. We have focused on the influence of chitosan molecular weight on nanoparticle properties. Larger molecular weight increased their porosity (=decreased cross-link density), and this caused also larger dimensional changes in response to variations in osmotic pressure or upon drying. The dependency of nanoparticle porosity on chitosan molecular weight had a profound effect on the adsorption of HA on the nanoparticles; HA was apparently able to penetrate deeply into the more porous high molecular weight (684 kDa) chitosan nanoparticles, while it formed a corona around those composed of more densely cross-linked low molecular weight (25 kDa) chitosan. Atomic Force Microscopy (AFM) allowed not only to highlight the presence of this corona, but also to estimate its apparent thickness to about 20-30 nm (in a dry state). The different morphology has a significant effect on the way HA is presented to biomolecules, and this has specific relevance in relation to interactions with HA receptors (e.g. CD44) that influence kinetics and mechanism of nanoparticle uptake. Finally, it is worth to mention that chitosan molecular weight did not appear to greatly affect the efficiency of nanoparticle loading with DNA, but significantly influenced its chitosanase-triggered release, with high molecular chitosan nanoparticles seemingly more prone to degradation by this enzyme. © 2013.

  7. Marine Biofouling of Surfaces: Morphology, and Nanomechanics of Barnacle Cyprid Adhesion Proteins by AFM

    NARCIS (Netherlands)

    Phang, In Yee

    2008-01-01

    The understanding of biointerfaces in contact with seawater is crucially important in tackling the problems of marine biofouling. Such biointerfaces involve the bioadhesives used by marine organisms to attach temporary or permanently to the surfaces immersed in water. The aim of this Thesis is to

  8. Surface morphology of thin lysozyme films produced by matrix-assisted pulsed laser evaporation (MAPLE)

    DEFF Research Database (Denmark)

    Purice, Andreea; Schou, Jørgen; Pryds, Nini

    2007-01-01

    Thin films of the protein, lysozyme, have been deposited by the matrix-assisted pulsed laser evaporation (MAPLE) technique. Frozen targets of 0.3-1.0 wt.% lysozyme dissolved in ultrapure water were irradiated by laser light at 355 mn with a fluence of 2 J/cm(2). The surface quality of the thin...

  9. Morphology, proliferation, and osteogenic differentiation of mesenchymal stem cells cultured on titanium, tantalum, and chromium surfaces

    DEFF Research Database (Denmark)

    Stiehler, Maik; Lind, M.; Mygind, Tina

    2007-01-01

    the interactions between human mesenchymal stem cells (MSCs) and smooth surfaces of titanium (Ti), tantalum (Ta), and chromium (Cr). Mean cellular area was quantified using fluorescence microscopy (4 h). Cellular proliferation was assessed by (3)H-thymidine incorporation and methylene blue cell counting assays (4...

  10. Ultra-morphology of root surface subsequent to periodontal instrumentation: A scanning electron microscope study

    Directory of Open Access Journals (Sweden)

    Parveen Dahiya

    2012-01-01

    Full Text Available Background: The aim of this study was to compare root surface characteristic following root planing with various hand and power driven instruments. Materials and Methods: A total of 20 single rooted teeth were used in this study, of which two specimens were used as control (no instrumentation done and remaining 18 specimens were equally divided into three groups. Specimens from each group were then subjected to root planing by one of the following instruments: (1 a Gracey curette (2 Ultrasonic tip and (3 a Rotary bur. In each case, the time required for scaling and root planing was measured. After treatment, the specimens were observed under scanning electron microscope and surface roughness was measured by using Roughness and loss of tooth substance index (RLTSI. Results: The mean RLTSI scores for Gracey curette, ultrasonic and rotary instrument group were 2.5, 2.0 and 0.667 respectively. The mean scores of time spent for scaling and root planing by Gracey curette, ultrasonic and rotary instrument group in seconds were 42.50, 35.83 and 54.50. Conclusion: All the three instruments namely Gracey curette, Ultrasonic tip and Rotary bur were effective in mechanical debridement of root surface. The results favoured the use of rotary instruments for root planing to achieve smooth clean root surface; however, the use of rotary instrument was more time consuming which might limit its use in clinical practice.

  11. Effects of morphology parameters on anti-icing performance in superhydrophobic surfaces

    Science.gov (United States)

    Nguyen, Thanh-Binh; Park, Seungchul; Lim, Hyuneui

    2018-03-01

    In this paper, we report the contributions of actual ice-substrate contact area and nanopillar height to passive anti-icing performance in terms of adhesion force and freezing time. Well-textured nanopillars with various parameters were fabricated via colloidal lithography and a dry etching process. The nanostructured quartz surface was coated with low-energy material to confer water-repellent properties. These superhydrophobic surfaces were investigated to determine the parameters essential for reducing adhesion strength and delaying freezing time. A well-textured surface with nanopillars of very small top diameter, regardless of height, could reduce adhesion force and delay freezing time in a subsequent de-icing process. Small top diameters of nanopillars also ensured the metastable Cassie-Baxter state based on energy barrier calculations. The results demonstrated the important role of areal fraction in anti-icing efficiency, and the negligible contribution of texture height. This insight into icing phenomena should lead to design of improved ice-phobic surfaces in the future.

  12. Structural and Morphological Evaluation of Presintered Zirconia following Different Surface Treatments.

    Science.gov (United States)

    Skienhe, Hasan; Habchi, Roland; Ounsi, Hani F; Ferrari, Marco; Salameh, Ziad

    2018-02-01

    The aim of this study was to evaluate the effect of different surface treatments on roughness, grain size, and phase transformation of presintered zirconia. Surface treatments included airborne particle abrasion (APA) before and after sintering with different particles shape, size, and pressure (50 μm Al 2 O 3 , 50 μm glass beads, and ceramic powder). Thirty-five square-shaped presin-tered yttrium-stabilized tetragonal zirconia polycrystal (Y-TZP) ceramic slabs (Zenostar ZR bridge, Wieland) were prepared (4 mm height × 10 mm width × 10 mm length) and polished with silicon carbide grit papers #800, 1000, 1200, 1500, and 2000 to ensure identical initial roughness. Specimens were divided into five groups according to surface treatment: group I (control): no surface treatment; group II: APA 50 μm Al 2 O 3 after sintering; group III: APA 50 μm Al 2 O 3 particles before sintering; group IV: APA 50 μm glass bead particles before sintering; and group V: APA ceramic powder before sintering. Specimens were analyzed using scanning electron microscopy (SEM), atomic force microscopy (AFM), X-ray diffraction (XRD) analyses, and tested for shear bond strength (SBS). Data were statistically analyzed using one-way analysis of variance (ANOVA) followed by post hoc tests for multiple comparisons Tukey's test (a > 0.05). Air abrasion before sintering significantly increased the surface roughness when compared with groups I and III. The highest tetragonal to monoclinic (t-m) phase transformation (0.07%) was observed in group III, and a reverse transformation was observed in presintered groups (0.01%). Regarding bond strength, there was a significant difference between APA procedures pre- and postsintering. Air abrasion before sintering is a valuable method for increasing surface roughness and SBS. The abrasive particles' size and type used before sintering had a little effect on phase transformation. Air abrasion before sintering could be supposed to be an alternative surface

  13. Morphological change study on root surfaces treated with curettes, sonic instruments or Er:YAG laser

    International Nuclear Information System (INIS)

    Guimaraes Filho, Arlindo Lopes

    2004-01-01

    Periodontal disease is caused by dental plaque and dental calculus on roots surfaces, specially on cervical areas. As dental plaque is the main cause and dental calculus a secondary one, it is practically impossible to separate one factor to the other one. In order to get periodontal tissue health it is necessary to eliminate dental plaque and calculus from root surfaces. In this sense, Er:YAG laser comes in as an excellent way to control periodontal disease, not only, by removing calculus and dental plaque but also for its bacteria reduction. The aim of this study is to compare, by S.E.M., root surfaces changing when they are treated with curettes and ultrasonic scaling or Er:YAG laser irradiation with two different energy levels of 60 mJ/pulse and 100 mJ/pulse and repetition tax of 10 Hz (in the display). It is also objective of this study to check a possible thermic damage to pulp tissue when the roots surfaces are irradiated with Er:YAG laser. We used for this study, five human dental roots, each one of them were cut into four samples, giving us a total of twenty samples, which were divided in five groups of four samples each one. The control group, we did not indicated any kind of treatment. The first group, the roots samples were scaled and planned with Gracey curettes 5/6 and 7/8. The second group, the roots samples were treated with ultrasonic instruments. The third group was irradiated with Er:YAG laser using 60 mJ/pulse , 10 Hz and energy density of 4 J/cm 2 (approximated). The fourth group was irradiated with Er:YAG laser using 100 mJ/pulse, 10 Hz and energy density of 7 J/cm 2 (approximated). The results analysis showed that roots scaling either with Gracey curettes or with ultrasonic instruments created smear layer covering roots surfaces; roots surfaces irradiated with Er:YAG laser showed few roughness in the third group; roots surfaces irradiated with Er:YAG laser showed no smear layer and the Er:YAG laser irradiation did not bring any thermic damage

  14. A scanning electron microscopic study of the surface morphology of nuptial pads in male amphibians (Genus: Bombina, Pelophylax, Rana

    Directory of Open Access Journals (Sweden)

    Pasqualina Kyriakopoulou-Sklavounou

    2012-07-01

    Full Text Available The fine structure of nuptial pad surface of the anuran amphibians Bombina variegata, Pelophylax epeiroticus, Pelophylax ridibundus and Rana dalmatina, was examined by scanning electron microscopy. Nuptial pads are cutaneous secondary sexual characters of males that appear during the breeding season and disappear afterwards following an annual cycle. In males of P. epeiroticus, P. ridibundus and R. dalmatina, nuptial pads were observed on the ventrolateral aspect of the first digit (the thumb as darkish and remarkably keratinized papillae. In males of B. variegata nuptial pads were almost black and very visible on the thumb, the second and the third digit of the front legs. They also extended on the ventral surface of the forearms. Under scanning electron microscope numerous small papillae were observed rising above pad’s surface. In P. epeiroticus, P. ridibundus and R. dalmatina, these papillae were almost rounded at the base while at the dome shaped top they had many microprocesses organised in groups, thus assuming the shape of a “flower” which differed slightly among these three ranid species. In B. variegata the protuberances were conical with heavily keratinized hooks without microprocesses. Our results show that surface morphology of nuptial pads is unique for each species and could be considered as a species-specific character.

  15. Insight of DFT and ab initio atomistic thermodynamics on the surface stability and morphology of In2O3

    Science.gov (United States)

    Zhang, Minhua; Wang, Wenyi; Chen, Yifei

    2018-03-01

    In2O3 catalysts show remarkable activity and selectivity in methanol synthesis from CO2 hydrogenation. In order to get insight into the surface stability of this catalyst, density functional theory and ab initio atomistic thermodynamics method were used to investigate the surface free energies of various facets as a function of oxygen chemical potential, as well as the influences of temperature, pressure and gas compositions. The results show that the (111) facet presents lowest surface free energy under oxygen-rich condition, while the indium-terminated (100) facet is the most stable one under oxygen-lean condition. Moreover, we applied Wulff construction to determine the equilibrium shape of In2O3 with different oxygen chemical potentials. The equilibrium shape under oxygen-lean condition is cubic, which only expose (100) facet, while, the equilibrium shape under oxygen-rich condition is octahedron, which only expose (111) facet. Meanwhile, the results agree well with what is observed experimentally. It is further predicted that Wulff shape of In2O3 exists in a truncated octahedron morphology in which the (100) surface becomes predominant plane under CO2 hydrogenation reaction conditions.

  16. Evaluation of the effect of three mouthwashes on the mechanical properties and surface morphology of several orthodontic wires: Anin vitrostudy.

    Science.gov (United States)

    Aghili, Hossein; Yassaei, Sogra; Eslami, Farzaneh

    2017-01-01

    The aim of this study was to evaluate and compare the changes in the mechanical properties and surface morphology of different orthodontic wires after immersion in three mouthwash solutions. In this in vitro study, five specimens of each of 0.016 inch nickel titanium (NiTi), coated NiTi, and stainless steel orthodontic wires were selected. The specimens were immersed in 0.05% sodium fluoride (NaF), 0.2% chlorhexidine, Zataria multiflora extract, and distilled water (control) for 1.5 h at 37°C. After immersion, loading and unloading forces at 0.5 mm intervals and the elastic modulus (E) of the wires were measured using a three-point bending test. Surface changes were observed with a scanning electron microscope (SEM). Two-way analysis of variance and Bonferroni tests were used to compare the properties of the wires. The level of significance was set at 0.05. Statistically significant changes in loading and unloading forces and E of the orthodontic wires were observed after immersion in different mouthwash solutions ( P wires ( P > 0.05). SEM images showed surface changes in some types ofthe orthodontic wires. The mouthwashes used in this study seemed to change the mechanical properties and surface quality of the orthodontic wires.

  17. [Effect of hydrofluoric acid concentration on the surface morphology and bonding effectiveness of lithium disilicate glass ceramics to resin composites].

    Science.gov (United States)

    Hailan, Qian; Lingyan, Ren; Rongrong, Nie; Xiangfeng, Meng

    2017-12-01

    This study aimed at determining the influence of hydrofluoric acid (HF) in varied concentrations on the surface morphology of lithium disilicate glass ceramics and bond durability between resin composites and post-treated lithium disilicate glass ceramics. After being sintered, ground, and washed, 72 as-prepared specimens of lithium disilicate glass ceramics with dimensions of 11 mm×13 mm×2 mm were randomly divided into three groups. Each group was treated with acid solution [32% phosphoric acid (PA) or 4% or 9.5% HF] for 20 s. Then, four acidified specimens from each group were randomly selected. One of the specimens was used to observe the surface morphology using scanning electron microscopy, and the others were used to observe the surface roughness using a surface roughness meter (including Ra, Rz, and Rmax). After treatment with different acid solutions in each group, 20 samples were further treated with silane coupling agent/resin adhesive/resin cement (Monobond S/Multilink Primer A&B/Multilink N), followed by bonding to a composite resin column (Filtek™ Z350) with a diameter of 3 mm. A total of 20 specimens in each group were randomly divided into two subgroups, which were used for measuring the microshear bond strength, with one of them subjected to cool-thermal cycle for 20 000 times. The surface roughness (Ra, Rz, and Rmax) of lithium disilicate glass ceramics treated with 4% or 9.5% HF was significantly higher than that of the ceramic treated with PA (Pglass ceramics treated with 9.5% HF also demonstrated better surface roughness (Rz and Rmax) than that of the ceramics treated with 4% HF. Cool-thermal cycle treatment reduced the bond strength of lithium disilicate glass ceramics in all groups (Pglass ceramics treated with HF had higher bond strength than that of the ceramics treated with PA. The lithium disilicate glass ceramics treated with 4% HF had higher bond strength than that of the ceramics treated with 9.5% HF (Pglass ceramics treated with 4

  18. Morphological and chemical optimization of microcantilever surfaces for thyroid system biosensing and beyond

    Energy Technology Data Exchange (ETDEWEB)

    Hill, Kasey [University of Tennessee, Knoxville, Tennessee 37996-1600 (United States)], E-mail: klhill2823@yahoo.com; Dutta, Pampa; Zareba, Adelajda; Eldridge, Melanie L. [University of Tennessee, Knoxville, Tennessee 37996-1600 (United States); Sepaniak, Michael J. [University of Tennessee, Knoxville, Tennessee 37996-1600 (United States)], E-mail: msepaniak@utk.edu

    2008-09-05

    The development of biosensors is vital in many areas of biotechnology and biomedical research. A prominent new class of label-free biosensors are those based on ligand-induced nanomechanical responses of microcantilevers (MCs). The interaction between biologically significant ligands with bioreceptors (e.g., antibodies or nuclear receptor proteins) immobilized on one side of the MC surface causes an apparent surface stress, resulting in static bending of the MC, which can be detected by an optical beam bending technique. The three key performance metrics of sensitivity, selectivity, and reversibility are foci of the work reported herein. The nature of the MC surface and the method by which the bioreceptor is immobilized influence these performance metrics and, hence, optimization studies involving these were conducted. In our work, the gold surface on one side of the MC is first activated via self-assembled monolayer formation with amino ethane thiol (AET) then reacted with glutaraldehyde (GA) as a crosslinker before finally functionalizing with the protein receptor. We report the effect of concentration, reaction time, and pH for these reagents on the magnitude of the nanomechanical responses using an anti-immunoglobulin G (anti-IgG) receptor: IgG ligand test system. By vapor depositing an alloy of silver and gold and then etching away the former, a nanostructured 'dealloyed' MC surface is created that outperforms a smooth gold MC in terms of nanomechanical responses. Optimization of the dealloying parameters (thickness, metal ratio) is also reported herein using the aforementioned anti-IgG-IgG system. Maximum response was obtained with these conditions: 150 nm dealloyed surface, 1 mM aqueous solution of AET-incubation time 1 h, 1% GA solution in 10 mM pH 8 phosphate buffered saline (PBS)-incubation time 3 h, and 0.5 mg mL{sup -1} of receptor protein solution in 10 mM pH 7 PBS-incubation time 1 h. Additionally, surprising results are reported when

  19. Morphological features of the copper surface layer under sliding with high density electric current

    Energy Technology Data Exchange (ETDEWEB)

    Fadin, V. V., E-mail: fvv@ispms.ru [Institute of Strength Physics and Materials Science SB RAS, Tomsk, 634055 (Russian Federation); Aleutdinova, M. I., E-mail: aleut@ispms.ru [Institute of Strength Physics and Materials Science SB RAS, Tomsk, 634055 (Russian Federation); Seversk Technological Institute, Branch of State Autonomous Educational Institution of Higher Professional Education “National Research Nuclear University “MEPhI”, Seversk, 636036 (Russian Federation); Rubtsov, V. Ye., E-mail: rvy@ispms.ru [Institute of Strength Physics and Materials Science SB RAS, Tomsk, 634055 (Russian Federation); National Research Tomsk Polytechnic University, Tomsk, 634050 (Russian Federation); Aleutdinova, V. A., E-mail: valery-aleut@yandex.ru [National Research St. Petersburg State Polytechnical University, St. Petersburg, 195251 (Russian Federation)

    2015-10-27

    Conductivity and wear intensity of copper under the influence of dry friction and electric current with contact density higher 100 A/cm{sup 2} are presented. It is shown that an increase in hardness and heat outflow from a friction zone leads to the reduction of wear intensity and current contact density increase corresponding to the beginning of catastrophic wear. Structural changes, such as the formation of FeO oxide and α-Fe particles in the copper surface layer, have also been found. It is observed that a worn surface is deformed according to a viscous liquid mechanism. Such singularity is explained in terms of appearance of high-excited atomic states in deforming micro-volumes near contact spots that lead to easy stress relaxation by local plastic shears in the vicinity of stress concentrators. In common this effect allows to achieve high wear resistance.

  20. Morphological Analysis (SEM) of the Surface of a Non-Noble Dental Alloy Subjected to Electrocorrosion

    Science.gov (United States)

    Baciu, E. R.; Grădinaru, I.; Baciu, M.; Vasluianu, R. I.; Cimpoesu, R.; Baciu, C.; Bejinariu, C.

    2017-06-01

    Corrosion consists in the degradation of a material under the chemical or electrochemical action of the environment where it is placed. The investigations carried out aimed to show the structural modifications produced in Co-Cr-Mo alloy, Robur 400 (Eisenbacher Dental - Waren ED GmbH, Germany) subjected to electrocorrosion in Fusayama-Mayer artificial saliva. The specimens prepared by mechanical polishing were analysed structurally by using a scanning electron microscope. During the tests run we could notice a general corrosion of the surfaces of the specimens made from Robur alloy. Through 2D and 3D microscopy and qualitative determinations of the luminous variation we could notice the effects of electrocorrosion tests on the surface of the metal material.

  1. Synthesis, Characterization, Electrochemical and Surface Morphologies of Polyazomethines Containing Silane and Phosphazene Units.

    Science.gov (United States)

    Temizkan, Kevser; Kaya, İsmet

    2017-09-01

    Polyazomethines containing silane and phosphazene groups were synthesized via elimination reactions of dihydroxy compounds containing imine bonding with phosphazane and silane dichloride. The structures of monomers and polymers containing phosphazane and silane groups were supported by 1 H-NMR, 13 C-NMR, FT-IR and UV-Vis techniques. Electrochemical properties of the prepared Schiff bases and polymers were given by cyclic voltammetric (CV) analysis. Thermal properties of synthesized monomers and polymers were determined by TG-DTA and TG-DTA, DMA and DSC techniques, respectively. Molecular mass distributions of polymers are determined with gel permeation chromatography (GPC) measurement. Morphologic images of polymers containing heteroatom (silane/phosphazene) and azomethine linkage in the main chain were investigated by SEM techniques. The electrochemical band gap values of SB-1, SB-2, P-1, P-2 and P-3 compounds were found as 3.09, 3.30, 2.63, 3.07 and 3.04 eV, respectively.

  2. THE IMPACT OF THE SURFACE MORPHOLOGY ON ENERGY CHARACTERISTICS OF NANOPOROUS CARBON MATERIAL

    Directory of Open Access Journals (Sweden)

    B.K. Ostafiychuk

    2014-05-01

    Full Text Available The impact of nanoporous carbon material (PCM morphology on its electrochemical behavior in aqueous electrolyte has been studied. The optimum concentration of aqueous lithium sulfate which provides the maximum specific energy characteristics of capacitor-type systems C/Li2SO4/C is determined. Capacitive parameters of electrochemical capacitors (EC in aqueous so­lutions of lithium, sodium and potassium sulfate which have different molar ratio have been stu­died by comparative analysis. Cyclic voltammograms at different scan rates show that the PCM ca­pacitive behavior in three electrolytes increases in the following order Li2SO4

  3. Periodic morphological modification developed on the surface of polyethersulfone by XeCl excimer laser photoablation

    International Nuclear Information System (INIS)

    Niino, H.; Nakano, M.; Nagano, S.; Yabe, A.; Miki, T.; Center for Structure Analyses, Teijin Limited, Asahigaoka, Hino, Tokyo, 191 Japan)

    1989-01-01

    Periodic and stable micropatterns appeared on the surface of amorphous polyethersulfone etched with an excimer laser at 308 nm in ambient air and a vacuum. The control of such radiative conditions as fluence and incident angle enables us to modify the spacing and pattern of the microstructures. A topographical investigation with scanning electron microscopy and an experiment with x-ray photoelectron spectroscopy to determine its composition is reported

  4. Investigation of antimicrobial activity and morphological properties of metal coated textile surfaces

    International Nuclear Information System (INIS)

    Aslan, Necdet; Sen, Tuba; Senturk, Kenan; Corukhlu, Turgay; Varturk, Ipek; Seker, S.; Shahidi, S.; Korachi, May; Dobrovolskiy, A.M.; Tsiolko, V.V.; Matsevich, S.V.; Keskin, S.S.

    2014-01-01

    The results of investigation antimicrobial and surface properties of the textiles metal coated by means of magnetron or the cleaning-deposition system, which is based on sequentially arranged DC anode layer accelerator and hollow cathode, are presented. The antimicrobial properties against bacteria E. coli and S. aureus of cotton and polyester/cotton textiles coated by Cu, Ti and Ag with the use of two different systems were examined and compared.

  5. Effects of NaOCl or Combination of NaOCl and Various Acids on Dentin Surface Morphology: A SEM Study

    Directory of Open Access Journals (Sweden)

    Gökçe Kağan

    2014-03-01

    Full Text Available The aim of this study was to evaluate by SEM morphological changes of dentin surfaces under the use of 5% NaOCl before applying different acids for etching. In the study, dentin surfaces were prepared from the middle third of 20 non-carious human third molars. Samples were divided into 2 groups with 3 subgroups each. In the first group, no application was performed on dentin surfaces. In the second group, 5% NaOCl was applied for 60 seconds on the dentin surfaces then rinsed with distilled water for 5 seconds. In all of the subgroups, dentin surfaces were etched by different conditioning agents for 15 seconds then rinsed for 30 seconds. After surface applications, all of the specimens were placed in distilled water. Morphological changes of dentin surfaces were determined by SEM. The results were evaluated by the scoring system based on Brannström et al.

  6. Hydrology and surface morphology of the Bonneville Salt Flats and Pilot Valley Playa, Utah

    Science.gov (United States)

    Lines, Gregory C.

    1979-01-01

    The Bonneville Salt Flats and Pilot Valley are in the western part of the Great Salt Lake Desert in northwest Utah. The areas are separate, though similar, hydrologic basins, and both contain a salt crust. The Bonneville salt crust covered about 40 square miles in the fall of 1976, and the salt crust in Pilot Valley covered 7 square miles. Both areas lack any noticeable surface relief (in 1976, 1.3 feet on the Bonneville salt crust and 0.3 foot on the Pilot Valley salt crust).The salt crust on the Salt Flats has been used for many years for automobile racing, and brines from shallow lacustrine deposits have been used for the production of potash. In recent years, there has been an apparent conflict between these two major uses of the area as the salt crust has diminished in both thickness and extent. Much of the Bonneville Racetrack has become rougher, and there has also been an increase in the amount of sediment on the south end of the racetrack. The Pilot Valley salt crust and surrounding playa have been largely unused.Evaporite minerals on the Salt Flats and the Pilot Valley playa are concentrated in three zones: (1) a carbonate zone composed mainly of authigenic clay-size carbonate minerals, (2) a sulfate zone composed mainly of authigenic gypsum, and (3) a chloride zone composed of crystalline halite (the salt crust). Five major types of salt crust were recognized on the Salt Flats, but only one type was observed in Pilot Valley. Geomorphic differences in the salt crust are caused by differences in their hydrologic environments. The salt crusts are dynamic features that are subject to change because of climatic factors and man's activities.Ground water occurs in three distinct aquifers in much of the western Great Salt Lake Desert: (1) the basin-fill aquifer, which yields water from conglomerate in the lower part of the basin fill, (2) the alluvial-fan aquifer, which yields water from sand and gravel along the western margins of both playas, and (3) the

  7. Morphological Analysis of Dentin Surface after Conditioning with Two Different methods: Chemical and Mechanical.

    Science.gov (United States)

    Rafael, Caroline Freitas; Quinelato, Valquíria; Morsch, Carolina Schaffer; DeDeus, Gustavo; Reis, Claudia Mendonca

    2016-01-01

    Alternative pretreatment strategies of dentin and adhesionare constantly being developed and studied with the goal of improving the adhesion of resin restorative materials with this tissue. The objectives of the present study were to evaluate the ability of airborne-particle abrasion (APA) with aluminum oxide on dentin to remove the smear layer and the effects produced on the dentin microstructure. The phosphoric acid (PA) was used for a comparison. For that, 20 human third molars were randomly allocated into two experimental groups, according to the dentin pretreatment method used: G1 (N = 10) - PA, G2 (N = 10) -APA. For dentin surface analyses, an environmental scanning electron microscope (ESEM) was employed to observe dentin surfaces before and after the procedures. Before pretreatment, the specimens of both groups were smear covered. After pretreatment, the G1 images revealed dentin tubule orifices opened, enlarged and some erosive effects. (G2) exposed tubule orifices without enlargement, but crack-like alterations were observed on the surfaces. In this way, APA with aluminum oxide was able to remove the smear layer. The influences of the dentin roughness on adhesion and the consequences on dentin integrity and hardness need further investigations. A good conditioning of the dentin before cementation is necessary in order to obtain a satisfactory rehabilitation in adhesive dentistry. So, it is necessary to know all methods to do it.

  8. The Effect of Growth Temperature and V/III Flux Ratio of MOCVD Antimony Based Semiconductors on Growth Rate and Surface Morphology

    Directory of Open Access Journals (Sweden)

    Ramelan Ari Handono

    2017-01-01

    Full Text Available Epitaxial Alx Ga1-x Sb layers on GaSb and GaAs substrates have been grown by atmospheric pressure metalorganic chemical vapor deposition using TMAl, TMGa and TMSb. Nomarski microscope and a profiler were employed to examine the surface morphology and growth rate of the samples. We report the effect of growth temperature and V/III flux ratio on growth rate and surface morphology. Growth temperatures in the range of 520°C and 680°C and V/III ratios from 1 to 5 have been investigated. A growth rate activation energy of 0.73 eV was found. At low growth temperatures between 520 and 540°C, the surface morphology is poor due to antimonide precipitates associated with incomplete decomposition of the TMSb. For layers grown on GaAs at 580°C and 600°C with a V/III ratio of 3 a high quality surface morphology is typical, with a mirror-like surface and good composition control. It was found that a suitable growth temperature and V/III flux ratio was beneficial for producing good AlGaSb layers. Undoped AlGaSb grown at 580°C with a V/III flux ratio of 3 at the rate of 3.5 μm/hour shows p-type conductivity with smooth surface morphology

  9. Internal Energy Dependence of Molecular Condensation Coefficients Determined from Molecular Beam Surface Scattering Experiments

    Science.gov (United States)

    Sibener, S. J.; Lee, Y. T.

    1978-05-01

    An experiment was performed which confirms the existence of an internal mode dependence of molecular sticking probabilities for collisions of molecules with a cold surface. The scattering of a velocity selected effusive beam of CCl{sub 4} from a 90 K CC1{sub 4} ice surface has been studied at five translational velocities and for two different internal temperatures. At a surface temperature of 90 K (approx. 99% sticking probability) a four fold increase in reflected intensity was observed for the internally excited (560 K) CC1{sub 4} relative to the room temperature (298 K) CC1{sub 4} at a translational velocity of 2.5 X 10{sup 4} cm/sec. For a surface temperature of 90 K all angular distributions were found to peak 15{sup 0} superspecularly independent of incident velocity.

  10. Dependence of Ideality Factor in Lateral PNP Transistors on Surface Carrier Concentration

    Science.gov (United States)

    Li, Xingji; Yang, Jianqun; Barnaby, Hugh J.; Galloway, Kenneth F.; Schrimpf, Ronald D.; Fleetwood, Daniel M.; Liu, Chaoming

    2017-06-01

    The influence of surface carrier concentration on the ideality factor of excess base current (ΔIB) in gated lateral PNP (GLPNP) bipolar junction transistors (BJTs) induced by 1-MeV electrons is investigated. ΔIB in LPNP BJTs is impacted by the surface carrier density and radiation-induced interface traps. In GLPNP BJTs, the surface carrier concentration can be controlled by the voltage applied to a gate over the base region. The ideality factor changes after irradiation, and its dependence on emitter-base voltage (VEB) is a function of gate voltage. For the irradiated devices, as the gate voltage decreases from +20 to -5 V, the ideality factor for excess base current changes from a single slope to two-slope behavior. The majority carrier concentration at the surface of the base, controlled by the gate voltage, impacts the excess base current and its ideality factor.

  11. Fast algorithm for Morphological Filters

    International Nuclear Information System (INIS)

    Lou Shan; Jiang Xiangqian; Scott, Paul J

    2011-01-01

    In surface metrology, morphological filters, which evolved from the envelope filtering system (E-system) work well for functional prediction of surface finish in the analysis of surfaces in contact. The naive algorithms are time consuming, especially for areal data, and not generally adopted in real practice. A fast algorithm is proposed based on the alpha shape. The hull obtained by rolling the alpha ball is equivalent to the morphological opening/closing in theory. The algorithm depends on Delaunay triangulation with time complexity O(nlogn). In comparison to the naive algorithms it generates the opening and closing envelope without combining dilation and erosion. Edge distortion is corrected by reflective padding for open profiles/surfaces. Spikes in the sample data are detected and points interpolated to prevent singularities. The proposed algorithm works well both for morphological profile and area filters. Examples are presented to demonstrate the validity and superiority on efficiency of this algorithm over the naive algorithm.

  12. Turbulent flows over superhydrophobic surfaces with shear-dependent slip length

    Science.gov (United States)

    Khosh Aghdam, Sohrab; Seddighi, Mehdi; Ricco, Pierre

    2015-11-01

    Motivated by recent experimental evidence, shear-dependent slip length superhydrophobic surfaces are studied. Lyapunov stability analysis is applied in a 3D turbulent channel flow and extended to the shear-dependent slip-length case. The feedback law extracted is recognized for the first time to coincide with the constant-slip-length model widely used in simulations of hydrophobic surfaces. The condition for the slip parameters is found to be consistent with the experimental data and with values from DNS. The theoretical approach by Fukagata (PoF 18.5: 051703) is employed to model the drag-reduction effect engendered by the shear-dependent slip-length surfaces. The estimated drag-reduction values are in very good agreement with our DNS data. For slip parameters and flow conditions which are potentially realizable in the lab, the maximum computed drag reduction reaches 50%. The power spent by the turbulent flow on the walls is computed, thereby recognizing the hydrophobic surfaces as a passive-absorbing drag-reduction method, as opposed to geometrically-modifying techniques that do not consume energy, e.g. riblets, hence named passive-neutral. The flow is investigated by visualizations, statistical analysis of vorticity and strain rates, and quadrants of the Reynolds stresses. Part of this work was funded by Airbus Group. Simulations were performed on the ARCHER Supercomputer (UKTC Grant).

  13. Spectrally adjusted surface reflectance and its dependence with NDVI for Landsat and Sentinel 2

    Science.gov (United States)

    Villaescusa, J. L.; Franch, B.; Roger, J. C.; Vermote, E.; Justice, C. O.

    2017-12-01

    Cross-calibration between sensors is necessary to bring measurements to a common radiometric scale; it allows a more complete monitoring of land surface processes and enhances data continuity and harmonization. However, differences in the Relative Spectral Response (RSR) of sensors generate uncertainties in the process (Teillet et al., 2004). For this reason, compensating for these differences is of great importance and can be achieved by using a spectral band adjustment factor (SBAF), which establishes a relationship between two spectrally adjusted bands. Nonetheless, this relationship has been shown to depend greatly on the surface's NDVI (Trishchenko et al., 2002) and therefore needs to be corrected. In this work, we use the Sentinel 2 and Landsat sensor's RSRs for both the Red and NIR bands to find the most accurate metric towards performing said relationship, and use surface reflectance spectral libraries with a wide variety of classes that include NDVI values ranging from -0.1 to 1 to analyze its dependence. We compute a quadratic fit of the metric used vs the surface's NDVI and propose an adjusted correction equation dependent on the NDVI value for both bands of all Landsat and Sentinel 2 sensors. Key words: Radiometric calibration, RSR, Spectral Adjustment, Landsat, Sentinel 2.

  14. Unusual surface morphology from digital elevation models of the Greenland ice sheet

    DEFF Research Database (Denmark)

    Ekholm, Simon; Keller, K.; Bamber, J.L.

    1998-01-01

    In this study of the North Greenland ice sheet, we have used digital elevation models to investigate the topographic signatures of a large ice flow feature discovered in 1993 and a unique surface anomaly which we believe has not been observed previously. The small scale topography of the flow...... feature is revealed in striking detail in a high-pass filtered elevation model. Furthermore, ice penetrating radar show that the sub-stream bed is rough with undulation amplitude increasing downstream. The new feature consists of two large depressions in the ice sheet connected by a long curving trench...

  15. Polarization Dependence of Surface Enhanced Raman Scattering on a Single Dielectric Nanowire

    Directory of Open Access Journals (Sweden)

    Hua Qi

    2012-01-01

    Full Text Available Our measurements of surface enhanced Raman scattering (SERS on Ga2O3 dielectric nanowires (NWs core/silver composites indicate that the SERS enhancement is highly dependent on the polarization direction of the incident laser light. The polarization dependence of the SERS signal with respect to the direction of a single NW was studied by changing the incident light angle. Further investigations demonstrate that the SERS intensity is not only dependent on the direction and wavelength of the incident light, but also on the species of the SERS active molecule. The largest signals were observed on an NW when the incident 514.5 nm light was polarized perpendicular to the length of the NW, while the opposite phenomenon was observed at the wavelength of 785 nm. Our theoretical simulations of the polarization dependence at 514.5 nm and 785 nm are in good agreement with the experimental results.

  16. The Fungal Pathogen Candida glabrata Does Not Depend on Surface Ferric Reductases for Iron Acquisition

    Directory of Open Access Journals (Sweden)

    Franziska Gerwi