WorldWideScience

Sample records for surface modifying agent

  1. Evaluation of Foaming Performance of Bitumen Modified with the Addition of Surface Active Agent

    Science.gov (United States)

    Chomicz-Kowalska, Anna; Mrugała, Justyna; Maciejewski, Krzysztof

    2017-10-01

    The article presents the analysis of the performance of foamed bitumen modified using surface active agents. Although, bitumen foaming permits production of asphalt concrete and other asphalt mix types without using chemical additives in significantly reduced temperatures, the decrease in processing temperatures still impacts the adhesion performance and bitumen coating of aggregates in final mixes. Therefore, in some cases it may be feasible to incorporate adhesion promoters and surface active agents into warm and half-warm mixes with foamed bitumen to increase their service life and resilience. Because of the various nature of the available surface active agents, varying bitumen compatibility and their possible impact on the rheological properties of bitumen, the introduction of surface active agents may significantly alter the bitumen foaming performance. The tests included basic performance tests of bitumen before and after foaming. The two tested bitumen were designated as 35/50 and 50/70 penetration grade binders, which were modified with a surface active agent widely used for improving mixture workability, compactibility and adhesion in a wide range of asphalt mixes and techniques, specifically Warm Mix Asphalt. Alongside to the reference unmodified bitumen, binders with 0.2%, 0.4% and 0.6% surface active agent concentration were tested. The analysis has shown a positive influence of the modifier on the foaming performance of both of the base bitumen increasing their maximum expansion ratio and bitumen foam halflife. In the investigations, it was found that the improvement was dependent on the bitumen type and modifier content. The improved expansion ratio and foam half-life has a positive impact on the aggregate coating and adhesion, which together with the adhesion promoting action of the modifier will have a combined positive effect on the quality of produced final asphalt mixes.

  2. Surface-modified sulfur nanoparticles: an effective antifungal agent against Aspergillus niger and Fusarium oxysporum.

    Science.gov (United States)

    Choudhury, Samrat Roy; Ghosh, Mahua; Mandal, Amrita; Chakravorty, Dipankar; Pal, Moumita; Pradhan, Saheli; Goswami, Arunava

    2011-04-01

    Surface-modified sulfur nanoparticles (SNPs) of two different sizes were prepared via a modified liquid-phase precipitation method, using sodium polysulfide and ammonium polysulfide as starting material and polyethylene glycol-400 (PEG-400) as the surface stabilizing agent. Surface topology, size distribution, surface modification of SNPs with PEG-400, quantitative analysis for the presence of sulfur in nanoformulations, and thermal stability of SNPs were determined by atomic force microscopy (AFM), dynamic light scattering (DLS) plus high-resolution transmission electron microscopy (HR-TEM), fourier transform infrared (FT-IR) spectroscopy, energy dispersive X-ray (EDX) spectroscopy, and thermogravimetric analysis (TGA), respectively. A simultaneous study with micron-sized sulfur (S(0)) and SNPs was carried out to evaluate their fungicidal efficacy against Aspergillus niger and Fusarium oxysporum in terms of radial growth, sporulation, ultrastructural modifications, and phospholipid content of the fungal strains using a modified poisoned food technique, spore-germination slide bioassay, environmental scanning electron microscopy (ESEM), and spectrometry. SNPs expressed promising inhibitory effect on fungal growth and sporulation and also significantly reduced phospholipid content. © Springer-Verlag 2011

  3. Chemical functionalization of ceramic tile surfaces by silane coupling agents: polymer modified mortar adhesion mechanism implications

    Directory of Open Access Journals (Sweden)

    Alexandra Ancelmo Piscitelli Mansur

    2008-09-01

    Full Text Available Adhesion between tiles and mortars are crucial to the stability of ceramic tile systems. From the chemical point of view, weak forces such as van der Waals forces and hydrophilic interactions are expected to be developed preferably at the tiles and polymer modified Portland cement mortar interface. The main goal of this paper was to use organosilanes as primers to modify ceramic tile hydrophilic properties to improve adhesion between ceramic tiles and polymer modified mortars. Glass tile surfaces were treated with several silane derivatives bearing specific functionalities. Contact angle measurements and Fourier Transform Infrared Spectroscopy (FTIR were used for evaluating the chemical changes on the tile surface. In addition, pull-off tests were conducted to assess the effect on adhesion properties between tile and poly(ethylene-co-vinyl acetate, EVA, modified mortar. The bond strength results have clearly shown the improvement of adherence at the tile-polymer modified mortar interface, reflecting the overall balance of silane, cement and polymer interactions.

  4. Effect of type and loading of surface-modifying agent on mechanical properties of modified geothermal scale powder/stereolithography polymer composite

    Science.gov (United States)

    Tilendo, A. C.; Pajarito, B. B.

    2017-05-01

    This study investigated the effect of stearic acid (SA), glycerol monostearate (GMS) and 3-trimethoxysilylpropyl methacrylate (TSPM) at varied loadings on the hardness and flexural properties of modified geothermal scale powder (GSP)/stereolithography (SLA) polymer composite. TSPM-modified GSP/SLA composite has the highest value of hardness due to increased filler dispersion and crystallinity. Hardness of GSP/SLA composite increases with loading of surface-modifying agent due to increase filler dispersion. Pronounced effect of surface modification to flexural modulus is observed. While low loading of SA and GMS leads to reduction of flexural modulus, increasing loading enhances the said property. Further increase of SA deteriorates the property. TSPM-modified GSP enhances the modulus due to increased crystalline phase of the system owing to TSPM copolymerization. Likewise, addition of SA and GMS increases flexural strength due to efficient reduction of filler agglomerates. However, unreacted TSPM produces weak interfaces and poor adhesion between GSP and SLA matrix.

  5. Dual-surface modified virus capsids for targeted delivery of photodynamic agents to cancer cells.

    Science.gov (United States)

    Stephanopoulos, Nicholas; Tong, Gary J; Hsiao, Sonny C; Francis, Matthew B

    2010-10-26

    Bacteriophage MS2 was used to construct a targeted, multivalent photodynamic therapy vehicle for the treatment of Jurkat leukemia T cells. The self-assembling spherical virus capsid was modified on the interior surface with up to 180 porphyrins capable of generating cytotoxic singlet oxygen upon illumination. The exterior of the capsid was modified with ∼20 copies of a Jurkat-specific aptamer using an oxidative coupling reaction targeting an unnatural amino acid. The capsids were able to target and selectively kill more than 76% of the Jurkat cells after only 20 min of illumination. Capsids modified with a control DNA strand did not target Jurkat cells, and capsids modified with the aptamer were found to be specific for Jurkat cells over U266 cells (a control B cell line). The doubly modified capsids were also able to kill Jurkat cells selectively even when mixed with erythrocytes, suggesting the possibility of using our system to target blood-borne cancers or other pathogens in the blood supply.

  6. Effect of Sb2O3 Modified by Various Surface Active Agents on Flame Retardant Properties of PVC Composite

    Directory of Open Access Journals (Sweden)

    XU Jian-lin

    2016-08-01

    Full Text Available Sb2O3 powders were prepared by high energy ball milling using polyethyleneglycol-6000,sodium dodecyl sulfate and OP-10 to modify the surface properties of the powder. The influence of Sb2O3 powders modified by various surface active agents on flame retardant properties of PVC composite materials was studied. The phase composition, morphology and the average particle size of the powders were characterized by XRD and TEM. The particle distribution and flame retardant properties of Sb2O3/PVC composite materials were studied by EDS, limiting oxygen index instrument and vertical burning test. The results show that nanometer Sb2O3 has good dispersion in the PVC matrix because of the higher space steric effect of organic film on the surface of nanometer Sb2O3 when polyethyleneglycol-6000 was used as the surface active agent. While the content of nanometer Sb2O3 is 1.26% in the PVC composite material, the oxygen index of the composite material is 27.1% and the composite material reaches fire retardant grade. Using sodium dodecyl sulfate and OP-10 as surface dispersants, the surface of Sb2O3 powders can not be coated completely. The particle size of Sb2O3 powders are 100nm and 150nm, respectively, The Sb2O3 powders have poor dispersion in the PVC matrix, and even some agglomerating phenomena took place. The oxygen index of Sb2O3/PVC composite materials are 24.7% and 25.3%, respectively, containing 1.26% Sb2O3 powders in Sb2O3/PVC composite material. The materials don't achieve flame retardant level.

  7. Surface modification agents for lithium batteries

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Zonghai; Amine, Khalil; Belharouak, Ilias

    2017-11-21

    An active material for an electrochemical device wherein a surface of the active material is modified by a surface modification agent, wherein the surface modification agent is an organometallic compound.

  8. Amphoteric surface active agents

    OpenAIRE

    Eissa, A.M. F.

    1995-01-01

    2-[trimethyl ammonium, triethyl ammonium, pyridinium and 2-amino pyridinium] alkanoates, four series of surface active agents containing carbon chain C12, C14, C16 and C18carbon atoms, were prepared. Their structures were characterized by microanalysis, infrared (IR) and nuclear magnetic resonance (NMR). Surface and interfacial tension, Krafft point, wetting time, emulsification power, foaming height a...

  9. Amphoteric surface active agents

    Directory of Open Access Journals (Sweden)

    Eissa, A.M. F.

    1995-10-01

    Full Text Available 2-[trimethyl ammonium, triethyl ammonium, pyridinium and 2-amino pyridinium] alkanoates, four series of surface active agents containing carbon chain C12, C14, C16 and C18carbon atoms, were prepared. Their structures were characterized by microanalysis, infrared (IR and nuclear magnetic resonance (NMR. Surface and interfacial tension, Krafft point, wetting time, emulsification power, foaming height and critical micelle concentration (cmc were determined and a comparative study was made between their chemical structure and surface active properties. Antimicrobial activity of these surfactants was also determined.

    Se prepararon cuatro series de agentes tensioactivos del tipo 2-[trimetil amonio, trietil amonio, piridinio y 2-amino piridinio] alcanoatos, que contienen cadenas carbonadas con C12, C14, C16 y C18 átomos de carbono.
    Se determinaron la tensión superficial e interfacial, el punto de Krafft, el tiempo humectante, el poder de emulsionamiento, la altura espumante y la concentración critica de miscela (cmc y se hizo un estudio comparativo entre la estructura química y sus propiedades tensioactivas. Se determinó también la actividad antimicrobiana de estos tensioactivos. Estas estructuras se caracterizaron por microanálisis, infrarrojo (IR y resonancia magnética nuclear (RMN.

  10. Disease Modifying Agents for Multiple Sclerosis

    OpenAIRE

    Hilas, Olga; Patel, Priti N; Lam, Sum

    2010-01-01

    Objective: To summarize major clinical trials which evaluate the efficacy and safety data of approved disease modifying agents for the treatment of various types of multiple sclerosis. Data Sources: A MEDLINE (1966 to August 2008) search of clinical trials using the terms multiple sclerosis, interferon, glatiramer, mitoxantrone and natalizumab was performed. A manual bibliographic search was also conducted. English-language articles identified from the searches were evaluated. New agents unde...

  11. Green Preparation of Epoxy/Graphene Oxide Nanocomposites Using a Glycidylamine Epoxy Resin as the Surface Modifier and Phase Transfer Agent of Graphene Oxide.

    Science.gov (United States)

    Tang, Xinlei; Zhou, Yang; Peng, Mao

    2016-01-27

    In studies of epoxy/graphene oxide (GO) nanocomposites, organic solvents are commonly used to disperse GO, and vigorous mechanical processes and complicated modification of GO are usually required, increasing the cost and hindering the development and application of epoxy nanocomposites. Here, we report a green, facile, and efficient method of preparing epoxy/GO nanocomposites. When triglycidyl para-aminophenol (TGPAP), a commercially available glycidyl amine epoxy resin with one tertiary amine group per molecule, is used as both the surface modifier and phase transfer agent of GO, GO can be directly and rapidly transferred from water to diglycidyl ether of bisphenol A and other types of epoxy resins by manual stirring under ambient conditions, whereas GO cannot be transferred to these epoxy resins in the absence of TGPAP. The interaction between TGPAP and GO and the effect of the TGPAP content on the dispersion of GO in the epoxy matrix were investigated systematically. Superior dispersion and exfoliation of GO nanosheets and remarkably improved mechanical properties, including tensile and flexural properties, toughness, storage modulus, and microhardness, of the epoxy/GO nanocomposites with a suitable amount of TGPAP were demonstrated. This method is organic-solvent-free and technically feasible for large-scale preparation of high-performance nanocomposites; it opens up new opportunities for exploiting the unique properties of graphene or even other nanofillers for a wide range of applications.

  12. Study of CaCl2 as an agent that modifies the surface of activated carbon used in sorption/treatment cycles for nitrate removal

    Directory of Open Access Journals (Sweden)

    O. Zanella

    2014-03-01

    Full Text Available The efficiency of the application of a chemically-modified activated carbon surface was investigated. The purpose of this study was to examine the effect of treatment with CaCl2 solution at a concentration of 2000 mg.L-1 on the sorption of nitrate ions from aqueous solutions in successive sorption/t reatment cycles. The sorbent was initially subjected to chemical treatment with CaCl2 and subsequently to the sorption process. Nine sorption cycles were performed. The concentrations of nitrate ions in the solution were measured by UV-Vis spectrophotometry before and after sorption. The results show that treatment with CaCl2 caused a significant increase in the percentage removal for each treatment step, reaching a removal rate of 80% of nitrate in the solution after nine cycles.

  13. Hydroxamic acid surface active agents

    Directory of Open Access Journals (Sweden)

    El-Sawy, A. A.

    2001-10-01

    Full Text Available p-Hydroxy phenyloctadecanol and p-hydroxy phenyloctadecanoic acid were used as new precursors for the preparation of surface active hydroxamic acid including different moles of propylene oxide. The hydroxamic acid was prepared by the reaction of propenoxylated products with sodium chloroacetate, followed by methyl esterification and the resultant product reacted with hydroxyl amine hydrochloride to give the hydroxamic acid. The structures of prepared hydroxamic acid were confirmed by spectroscopic study. The surface activity of prepared hydroxamic acid was studied; the results revealed that, the prepared hydroxamic acid has pronounced surface activity, the alcohol substrate shows a surface activity superior than the acid substrate.Se han utilizado el p-hidroxifeniloctadecanol y el ácido p-hidroxifeniloctadecanoico como nuevos precursores para la preparación de tensioactivos derivados del ácido hidroxámico, que incluyen diferentes moles de óxido de propileno. El ácido hidroxámico se preparó por reacción de los productos propenoxilados con cloroacetato sódico, seguido de la formación de ésteres metílicos, y los productos resultantes se hicieron reaccionar con clorhidrato de hidroxilamina para dar los derivados del ácido hidroxámico. Las estructuras de los derivados preparados del ácido hidroxámico, se confirmaron por técnicas espectroscópicas, estudiándose su actividad superficial cuyos resultados mostraron que dichos compuestos tenían un alto valor. La actividad superficial del sustrato alcohólico fue mayor que la del sustrato ácido.

  14. Surface modification of basalt with silane coupling agent on asphalt mixture moisture damage

    Energy Technology Data Exchange (ETDEWEB)

    Min, Yahong; Fang, Ying; Huang, Xiaojun; Zhu, Yinhui; Li, Wensheng [College of Chemistry and Chemical Engineering, Hunan University, Changsha, 410082 (China); Yuan, Jianmin [College of Materials Engineering, Hunan University, Changsha, 410082 (China); Tan, Ligang [College of Mechanical and Vehicle Engineering, Hunan University, Changsha, 410082 (China); Wang, Shuangyin [State Key Laboratory of Chem/Bio-Sensing and Chemometrics, College of Chemistry and Chemical Engineering, Hunan University, Changsha, 410082 (China); Wu, Zhenjun, E-mail: wooawt@163.com [College of Chemistry and Chemical Engineering, Hunan University, Changsha, 410082 (China)

    2015-08-15

    Graphical abstract: - Highlights: • A new silane coupling agent was synthesized based on KH570. • Basalt surface was modified using the new silane coupling agent. • Chemical bond between basalt and the new silane coupling agent was formed. • Asphalt mixture which used modified basalt show superior water stability. - Abstract: A new silane coupling agent was synthesized based on γ-(methacryloyloxy) propyltrimethoxysilane (KH570). The surface of basalt rocks was modified by KH570 and the new silane coupling agent (NSCA), and the interfacial interaction between silane coupling agent and basalt was also studied. Fourier transform infrared (FTIR) spectroscopy and X-ray photoelectron spectroscopy (XPS) analysis showed that the silane coupling agent molecule bound strongly with basalt rocks. Scanning electronic microscopy (SEM) observation showed that a thin layer of coupling agent was formed on the surface of modified basalt. The boiling test and immersion Marshall test confirmed that the moisture sensitivity of basalt modified with the new silane coupling agent increased more significantly than that untreated and treated with KH570. The Retained Marshall Strength of basalt modified with the new coupling agent increased from 71.74% to 87.79% compared with untreated basalt. The results indicated that the new silane coupling agent played an important role in improving the interfacial performance between basalt and asphalt.

  15. Surface treated fly ash filled modified epoxy composites

    Directory of Open Access Journals (Sweden)

    Uma Dharmalingam

    2015-01-01

    Full Text Available Abstract Fly ash, an inorganic alumino silicate has been used as filler in epoxy matrix, but it reduces the mechanical properties due to its poor dispersion and interfacial bonding with the epoxy matrix. To improve its interfacial bonding with epoxy matrix, surface treatment of fly ash was done using surfactant sodium lauryl sulfate and silane coupling agent glycidoxy propyl trimethoxy silane. An attempt is also made to reduce the particle size of fly ash using high pressure pulverizer. To improve fly ash dispersion in epoxy matrix, the epoxy was modified by mixing with amine containing liquid silicone rubber (ACS. The effect of surface treated fly ash with varying filler loadings from 10 to 40% weight on the mechanical, morphological and thermal properties of modified epoxy composites was investigated. The surface treated fly ash was characterized by particle size analyzer and FTIR spectra. Morphological studies of surface treated fly ash filled modified epoxy composites indicate good dispersion of fillers in the modified epoxy matrix and improves its mechanical properties. Impact strength of the surface treated fly ash filled modified epoxy composites show more improvement than unmodified composites.

  16. Protein surface shielding agents in protein crystallization

    International Nuclear Information System (INIS)

    Hašek, J.

    2011-01-01

    The crystallization process can be controlled by protein surface shielding agents blocking undesirable competitive adhesion modes during non-equilibrium processes of deposition of protein molecules on the surface of growing crystalline blocks. The hypothesis is based on a number of experimental proofs from diffraction experiments and also retrieved from the Protein Data Bank. The molecules adhering temporarily on the surface of protein molecules change the propensity of protein molecules to deposit on the crystal surface in a definite position and orientation. The concepts of competitive adhesion modes and protein surface shielding agents acting on the surface of molecules in a non-equilibrium process of protein crystallization provide a useful platform for the control of crystallization. The desirable goal, i.e. a transient preference of a single dominating adhesion mode between protein molecules during crystallization, leads to uniform deposition of proteins in a crystal. This condition is the most important factor for diffraction quality and thus also for the accuracy of protein structure determination. The presented hypothesis is a generalization of the experimentally well proven behaviour of hydrophilic polymers on the surface of protein molecules of other compounds

  17. Modifying glass surfaces via internal diffusion

    DEFF Research Database (Denmark)

    Smedskjaer, M.M.; Yue, Y.Z.; Deubener, J.

    2010-01-01

    The surface chemistry and structure of iron-bearing silicate glasses have been modified by means of heat-treatment around the glass transition temperature under different gaseous media at ambient pressure. When the glasses are heat-treated in atmospheric air, oxidation of Fe2+ to Fe3+ occurs, which......- ions in the network and their strong attraction to the modifying ions, whereas the latter is due to the requirement of the charge neutrality. The role of N3- in driving OD is verified by the composition profile of the surface layer of the glass treated in pure N-2 gas. The OD exerts pronounced impacts...

  18. Characterization of electrochemically modified polycrystalline platinum surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Krebs, L.C.; Ishida, Takanobu.

    1991-12-01

    The characterization of electrochemically modified polycrystalline platinum surfaces has been accomplished through the use of four major electrochemical techniques. These were chronoamperometry, chronopotentiommetry, cyclic voltammetry, and linear sweep voltammetry. A systematic study on the under-potential deposition of several transition metals has been performed. The most interesting of these were: Ag, Cu, Cd, and Pb. It was determined, by subjecting the platinum electrode surface to a single potential scan between {minus}0.24 and +1.25 V{sub SCE} while stirring the solution, that the electrocatalytic activity would be regenerated. As a consequence of this study, a much simpler method for producing ultra high purity water from acidic permanganate has been developed. This method results in water that surpasses the water produced by pyrocatalytic distillation. It has also been seen that the wettability of polycrystalline platinum surfaces is greatly dependent on the quantity of oxide present. Oxide-free platinum is hydrophobic and gives a contact angle in the range of 55 to 62 degrees. We have also modified polycrystalline platinum surface with the electrically conducting polymer poly-{rho}-phenylene. This polymer is very stable in dilute sulfuric acid solutions, even under applied oxidative potentials. It is also highly resistant to electrochemical hydrogenation. The wettability of the polymer modified platinum surface is severely dependent on the choice of supporting electrolyte chosen for the electrochemical polymerization. Tetraethylammonium tetrafluoroborate produces a film that is as hydrophobic as Teflon, whereas tetraethylammonium perchlorate produces a film that is more hydrophilic than oxide-free platinum.

  19. Characterization of electrochemically modified polycrystalline platinum surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Krebs, Leonard C. [State Univ. of New York (SUNY), Stony Brook, NY (United States); Ishida, Takanobu [State Univ. of New York (SUNY), Stony Brook, NY (United States)

    1991-12-01

    The characterization of electrochemically modified polycrystalline platinum surfaces has been accomplished through the use of four major electrochemical techniques. These were chronoamperometry, chronopotentiommetry, cyclic voltammetry, and linear sweep voltammetry. A systematic study on the under-potential deposition of several transition metals has been performed. The most interesting of these were: Ag, Cu, Cd, and Pb. It was determined, by subjecting the platinum electrode surface to a single potential scan between -0.24 and +1.25 VSCE while stirring the solution, that the electrocatalytic activity would be regenerated. As a consequence of this study, a much simpler method for producing ultra high purity water from acidic permanganate has been developed. This method results in water that surpasses the water produced by pyrocatalytic distillation. It has also been seen that the wettability of polycrystalline platinum surfaces is greatly dependent on the quantity of oxide present. Oxide-free platinum is hydrophobic and gives a contact angle in the range of 55 to 62 degrees. We have also modified polycrystalline platinum surface with the electrically conducting polymer poly-ρ-phenylene. This polymer is very stable in dilute sulfuric acid solutions, even under applied oxidative potentials. It is also highly resistant to electrochemical hydrogenation. The wettability of the polymer modified platinum surface is severely dependent on the choice of supporting electrolyte chosen for the electrochemical polymerization. Tetraethylammonium tetrafluoroborate produces a film that is as hydrophobic as Teflon, whereas tetraethylammonium perchlorate produces a film that is more hydrophilic than oxide-free platinum.

  20. Surface-modified nanocrystalline ceramics for drug delivery applications.

    Science.gov (United States)

    Kossovsky, N; Gelman, A; Sponsler, E E; Hnatyszyn, H J; Rajguru, S; Torres, M; Pham, M; Crowder, J; Zemanovich, J; Chung, A

    1994-12-01

    Drug delivery systems comprised of various types of carriers have long been the object of pharmacological investigation. The search has been stimulated by the belief that carriers will lead to reduced drug toxicity, dosage requirements, enhanced cellular targeting and improved shelf-life. Among the carriers investigated are complex polymeric carbohydrates, synthetic proteins and liposomal structures. For the past four years, we have been experimenting with a radically new class of carriers comprised of surface-modified nanocrystalline ceramics. While the ceramics provide the structural stability of a largely immutable solid, the surface modification creates a glassy molecular stabilization film to which pharmacological agents may be bound non-covalently from an aqueous phase with minimal structural denaturation. As a consequence of maintained structural integrity and owing to concentration effects afforded by the surfaces of the nanocrystalline materials, drug activity following surface immobilization is preserved. We have used successfully surface-modified nanocrystalline ceramics to deliver viral antigens for the purpose of evoking an immune response, oxygenated haemoglobin for cell respiration and insulin for carbohydrate metabolism. The theoretical principles, technical details and experimental results are reviewed. Surface-modified nanocrystalline materials offer an exciting new approach to the well-recognized challenges of drug delivery.

  1. Adsorption of hexavalent chromium on modified corn stalk using different cross-linking agents

    Science.gov (United States)

    Chen, Suhong; Zhu, Yi; Han, Zhijun; Feng, Gao; Jia, Yuling; Fu, Kaifang; Yue, Qinyan

    2017-12-01

    In this study, four different types of adsorbents modified from corn stalk were synthesized after the reaction with epichlorohydrin, N,N-dimethylformamide, triethylamine and different cross-linking agents. The surface functional groups and thermal stability of modified corn stalk (MCSs) were characterized using FTIR and TG analysis, respectively. The feasibility of using MCSs to remove Cr(VI) were evaluated. Adsorption isotherms were determined and modeled with Langmuir, Freundlich and Temkin equations. The experimental results showed that MCS modified using diethylenetriamine (DETA) had the best modification effect, and the adsorption capacity of Cr(VI) reached as high as 227.27 mg/g at 323 K. Thermodynamic study showed that the Cr(VI) adsorption onto MCSs was endothermic processes. As a result, MCS by using DETA as cross-linking agent has good potential for the removal of Cr(VI) from aqueous solutions.

  2. Osteoblastic cell behaviour on modified titanium surfaces.

    Science.gov (United States)

    Lukaszewska-Kuska, Magdalena; Wirstlein, Przemysław; Majchrowski, Radomir; Dorocka-Bobkowska, Barbara

    2018-02-01

    The surfaces of endoosseous dental implants have been subjected to numerous modifications in order to create a surface which can provide rapid bone healing and fast implant loading. Each modification has involved changes to the chemical composition and topography of the surfaces which have resulted in various biological reactions to the implanted material. The aim of this study was to evaluate the surface topography and chemistry of various modified titanium surfaces: (1) machined surface (MA), (2) alumina-blasted (Al2O3), (3) alumina-blasted and acid-etched (Al2O3 DE), (4) hydroxyapatite/tricalcium phosphate grit-blasted (HA/TCP) and (5) hydroxyapatite/tricalcium phosphate grit-blasted and acid-etched (HA/TCP DE) and to analyse the effects of surface roughness, and chemical composition on human osteoblast vitality, differentiation, morphology and orientation. The modified surfaces were subjected to topographic analysis using Scanning Electron Microscopy (SEM), optical profilometry, roughness analysis and chemical composition evaluation using Energy Dispersion Spectroscopy (EDS) analysis. The biological effects of the titanium modifications was analysed using human osteoblasts cell culture where the cell morphology, vitality (MTS assay) and differentiation (ALP activity) was analysed. The machined surfaces were classified as anisotropic, smooth and composed of titanium and oxygen. The blasted surface samples along with the blasted and etched samples were found to be isotropic and rough. The grit-blasting procedure resulted in the incorporation of components from the blasting material. In the case of the blasted and etched samples, etching decreased the surface development as indicated by the Sdr and also reduced the amount of chemical compounds incorporated into the surfaces during the blasting procedure. The attached NHOst cells, proliferated the surfaces. With regard to the MA samples, the cells spread close to the titanium surface, with expanded cytoplasmic

  3. Nonleaching antimicrobial films prepared from surface-modified microfibrillated cellulose.

    Science.gov (United States)

    Andresen, Martin; Stenstad, Per; Møretrø, Trond; Langsrud, Solveig; Syverud, Kristin; Johansson, Leena-Sisko; Stenius, Per

    2007-07-01

    We have prepared potentially permanent antimicrobial films based on surface-modified microfibrillated cellulose (MFC). MFC, obtained by disintegration of bleached softwood sulfite pulp in a homogenizer, was grafted with the quaternary ammonium compound octadecyldimethyl(3-trimethoxysilylpropyl)ammonium chloride (ODDMAC) by a simple adsorption-curing process. Films prepared from the ODDMAC-modified MFC were characterized by Fourier transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS) and tested for antibacterial activity against the Gram-positive bacterium Staphylococcus aureus and the Gram-negative bacteria Escherichia coli and Pseudomonas aeruginosa. The films showed substantial antibacterial capacity even at very low concentrations of antimicrobial agent immobilized on the surface. A zone of inhibition test demonstrated that no ODDMAC diffused into the surroundings, verifying that the films were indeed of the nonleaching type.

  4. Photocatalysis of Modified Transition Metal Oxide Surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Batzill, Matthias

    2018-02-28

    The goal of this project has been to establish a cause-effect relationship for photocatalytic activity variations of different structures of the same material; and furthermore gain fundamental understanding on modification of photocatalysts by compositional or surface modifications. The reasoning is that gaining atomic scale understanding of how surface and bulk modifications alter the photo reactivity will lead to design principles for next generation photocatalysts. As a prototypical photocatalyst the research focused on TiO2 synthesized in well-defined single crystalline form to enable fundamental characterizations.We have obtained results in the following areas: (a) Preparation of epitaxial anataseTiO2 samples by pulsed laser deposition. (b) Comparison of hydrogen diffusion on different crystallographic surface. (c) Determining the stability of the TiO2(011)-2x1 reconstruction upon interactions with adsorbates. (d) Characterization of adsorption and (thermal and photo) reaction of molecules with nitro-endgroups, (e) Exploring the possibility of modifying planar model photocatalyst surfaces with graphene to enable fundamental studies on reported enhanced photocatalytic activities of graphene modified transition metal oxides, (f) gained fundamental understanding on the role of crystallographic polymorphs of the same material for their photocatalytic activities.

  5. Adhesion of Aeromonas hydrophila to Glass Surfaces Modified with Organosilanes

    Directory of Open Access Journals (Sweden)

    Dorota Kregiel

    2013-01-01

    Full Text Available The aim of this research is to study the adhesive properties of Aeromonas hydrophila to glass surfaces modified using four silanes with different reactive groups, namely (3-glycidoxypropyl diethoxysilane, (3-N,N-dimethyl-3-N-n hexadecylammoniopropyltrimethoxysilane chloride, (3-N,N,N-triethanolammoniopropyltrimethoxysilane chloride, and (3-N,N-dimethyl- 3-N-n-octylammoniopropyltrimethoxysilane chloride. The strain used in the study was A. hydrophila LOCK0968, isolated from the unchlorinated communal water distribution system in Poland. The effect of glass modification after chemical treatment was analyzed using surface tension measurement. The adhesive properties of the bacteria were studied in a water environment with a low concentration of organic compounds, using luminometric and microscopic methods. Additionally, the viability of the adherent bacterial cells was evaluated by counting the colony-forming units. The presence of active compounds in the culture medium after incubation with a modified carrier was verified using the Kirby- -Bauer method. Half of the chemically modified glass surfaces exhibited better characteristics in comparison with native glass. Among the examined modifying agents, (3-N,N,N-triethanolammoniopropyl trimethoxysilane chloride and (3-N,N-dimethyl-3-N-n octylammoniopropyl trimethoxysilane chloride showed the best antiadhesive and antibacterial properties. The most effective glass modification, with (3-N,N,N triethanolammoniopropyltrimethoxysilane chloride, was able to reduce the bacterial cell count by more than three orders of magnitude. The carriers had no significant effect on the viability of the free bacterial cells in the culture medium. Therefore, it can be said that the modified glass surface alone accounts for the antibacterial activity of the active organosilanes.

  6. Environmentally responsive surface-modified silica nanoparticles for enhanced oil recovery

    International Nuclear Information System (INIS)

    Behzadi, Abed; Mohammadi, Aliasghar

    2016-01-01

    Environmentally responsive surface-modified nanoparticles are colloidal nanoparticles coated with, at least, two physicochemically distinct surface groups. Recent advances in the synthesis and production of nanoparticles have enabled the production of environmentally responsive surface-modified nanoparticles with both hydrophilic and hydrophobic surface groups. These nanoparticles act like colloidal surfactants. In this paper, environmentally responsive surface-modified silica nanoparticles are synthesized and used for enhancement of oil recovery. For this purpose, silica nanoparticles are coated with polyethylene glycol chains as hydrophilic agent and propyl chains as hydrophobic agent at various quantities, and their ability to modulate oil–water interface properties and oil recovery is examined. Oil–water interfacial tension and water surface tension are decreased by 50 % in the presence of silica nanoparticles coated with both agents. Measuring oil-drop contact angle on oil-wetted glass slides and carbonate rock sections, after aging in various surface-modified silica nanofluids, indicates that the wettability of various oil-wetted surfaces is modified from strongly oil-wet to water-wet. Flooding nanofluids to glass micro-models and pore-level investigations demonstrate that surface modification of silica nanoparticles, specially, with both hydrophilic and hydrophobic agents improves considerably their performance in increasing oil recovery and wettability alteration.

  7. Environmentally responsive surface-modified silica nanoparticles for enhanced oil recovery

    Energy Technology Data Exchange (ETDEWEB)

    Behzadi, Abed; Mohammadi, Aliasghar, E-mail: amohammadi@sharif.edu [Sharif University of Technology, Department of Chemical and Petroleum Engineering (Iran, Islamic Republic of)

    2016-09-15

    Environmentally responsive surface-modified nanoparticles are colloidal nanoparticles coated with, at least, two physicochemically distinct surface groups. Recent advances in the synthesis and production of nanoparticles have enabled the production of environmentally responsive surface-modified nanoparticles with both hydrophilic and hydrophobic surface groups. These nanoparticles act like colloidal surfactants. In this paper, environmentally responsive surface-modified silica nanoparticles are synthesized and used for enhancement of oil recovery. For this purpose, silica nanoparticles are coated with polyethylene glycol chains as hydrophilic agent and propyl chains as hydrophobic agent at various quantities, and their ability to modulate oil–water interface properties and oil recovery is examined. Oil–water interfacial tension and water surface tension are decreased by 50 % in the presence of silica nanoparticles coated with both agents. Measuring oil-drop contact angle on oil-wetted glass slides and carbonate rock sections, after aging in various surface-modified silica nanofluids, indicates that the wettability of various oil-wetted surfaces is modified from strongly oil-wet to water-wet. Flooding nanofluids to glass micro-models and pore-level investigations demonstrate that surface modification of silica nanoparticles, specially, with both hydrophilic and hydrophobic agents improves considerably their performance in increasing oil recovery and wettability alteration.

  8. Environmentally responsive surface-modified silica nanoparticles for enhanced oil recovery

    Science.gov (United States)

    Behzadi, Abed; Mohammadi, Aliasghar

    2016-09-01

    Environmentally responsive surface-modified nanoparticles are colloidal nanoparticles coated with, at least, two physicochemically distinct surface groups. Recent advances in the synthesis and production of nanoparticles have enabled the production of environmentally responsive surface-modified nanoparticles with both hydrophilic and hydrophobic surface groups. These nanoparticles act like colloidal surfactants. In this paper, environmentally responsive surface-modified silica nanoparticles are synthesized and used for enhancement of oil recovery. For this purpose, silica nanoparticles are coated with polyethylene glycol chains as hydrophilic agent and propyl chains as hydrophobic agent at various quantities, and their ability to modulate oil-water interface properties and oil recovery is examined. Oil-water interfacial tension and water surface tension are decreased by 50 % in the presence of silica nanoparticles coated with both agents. Measuring oil-drop contact angle on oil-wetted glass slides and carbonate rock sections, after aging in various surface-modified silica nanofluids, indicates that the wettability of various oil-wetted surfaces is modified from strongly oil-wet to water-wet. Flooding nanofluids to glass micro-models and pore-level investigations demonstrate that surface modification of silica nanoparticles, specially, with both hydrophilic and hydrophobic agents improves considerably their performance in increasing oil recovery and wettability alteration.

  9. Capsid Modified Bluetongue Virus 16 (BTV16 as a Virulytic Oncotherapy Agent

    Directory of Open Access Journals (Sweden)

    Taghi Naserpour Farivar

    2017-03-01

    Full Text Available Objective Using potential viruses to destroy cancer cells has a long history, but recent advances in molecular biology raised hopes for successful use of these viruses again. Methods Octreotate sequence was inserted into the neutralization region (R1& R2 in vp2 protein of capsid segment in 10 segmented genome of BTV in 304 - 368 position. T7 BTV RNA transcripts were extracted. Cancerous cultured cells were transfected with wild and modified BTV to recover BTV with cDNA-derived genome segments. Results The results of all the performed experiments revealed that treatment of AGS cell lines with VP2 modified BTV16, which targeted cell surface of cancerous cells, significantly increased apoptosis in cancer infected cells. Conclusions Modified VP2 BTV16 may be used as a potential virulytic oncotherapy agent in AGS cells.

  10. Modified Gadonanotubes as a promising novel MRI contrasting agent.

    Science.gov (United States)

    Jahanbakhsh, Rouzbeh; Atyabi, Fatemeh; Shanehsazzadeh, Saeed; Sobhani, Zahra; Adeli, Mohsen; Dinarvand, Rassoul

    2013-07-01

    Carbon nanotubes (CNTs) are emerging drug and imaging carrier systems which show significant versatility. One of the extraordinary characteristics of CNTs as Magnetic Resonance Imaging (MRI) contrasting agent is the extremely large proton relaxivities when loaded with gadolinium ion (Gdn3+) clusters. In this study equated Gdn3+ clusters were loaded in the sidewall defects of oxidized multiwalled (MW) CNTs. The amount of loaded gadolinium ion into the MWCNTs was quantified by inductively coupled plasma (ICP) method. To improve water solubility and biocompatibility of the system, the complexes were functionalized using diamine-terminated oligomeric poly (ethylene glycol) via a thermal reaction method. Gdn3+ loaded PEGylated oxidized CNTs (Gdn3+@CNTs-PEG) is freely soluble in water and stable in phosphate buffer saline having particle size of about 200 nm. Transmission electron microscopy (TEM) images clearly showed formation of PEGylated CNTs. MRI analysis showed that the prepared solution represents 10% more signal intensity even in half concentration of Gd3+ in comparison with commerciality available contrasting agent Magnevist®. In addition hydrophilic layer of PEG at the surface of CNTs could prepare stealth nanoparticles to escape RES. It was shown that Gdn3+@CNTs-PEG was capable to accumulate in tumors through enhanced permeability and retention effect. Moreover this system has a potential for early detection of diseases or tumors at the initial stages.

  11. Modified Gadonanotubes as a Promising Novel MRI Contrasting Agent

    Directory of Open Access Journals (Sweden)

    Rouzbeh Jahanbakhsh

    2013-07-01

    Full Text Available Background and purpose of the study:Carbon nanotubes (CNTs are emerging drug and imaging carrier systems which show significant versatility. One of the extraordinary characteristics of CNTs as Magnetic Resonance Imaging (MRI contrasting agent is the extremely large proton relaxivities when loaded with gadolinium ion (Gdn3+ clusters.Methods:In this study equated Gdn3+ clusters were loaded in the sidewall defects of oxidized multiwalled (MW CNTs. The amount of loaded gadolinium ion into the MWCNTs was quantified by inductively coupled plasma (ICP method. To improve water solubility and biocompatibility of the system, the complexes were functionalized using diamine-terminated oligomeric poly (ethylene glycol via a thermal reaction method.Results:Gdn3+ loaded PEGylated oxidized CNTs (Gdn3+@CNTs-PEG is freely soluble in water and stable in phosphate buffer saline having particle size of about 200 nm. Transmission electron microscopy (TEM images clearly showed formation of PEGylated CNTs. MRI analysis showed that the prepared solution represents 10% more signal intensity even in half concentration of Gd3+ in comparison with commerciality available contrasting agent Magnevist®. In addition hydrophilic layer of PEG at the surface of CNTs could prepare stealth nanoparticles to escape RES.Conclusion:It was shown that Gdn3+@CNTs-PEG was capable to accumulate in tumors through enhanced permeability and retention effect. Moreover this system has a potential for early detection of diseases or tumors at the initial stages.

  12. Modified natural nanoparticles as contrast agents for medical imaging

    NARCIS (Netherlands)

    Cormode, David P.; Jarzyna, Peter A.; Mulder, Willem J. M.; Fayad, Zahi A.

    2010-01-01

    The development of novel and effective contrast agents is one of the drivers of the ongoing improvement in medical imaging. Many of the new agents reported are nanoparticle-based. There are a variety of natural nanoparticles known, e.g. lipoproteins, viruses or ferritin. Natural nanoparticles have

  13. Effect of acidic agents on surface roughness of dental ceramics

    Directory of Open Access Journals (Sweden)

    Boonlert Kukiattrakoon

    2011-01-01

    Conclusion: Acidic agents used in this study negatively affected the surface of ceramic materials. This should be considered when restoring the eroded tooth with ceramic restorations in patients who have a high risk of erosive conditions.

  14. Effect of nano silica based modifying agent for hydrophobic coating application

    International Nuclear Information System (INIS)

    Nurul Huda Mudri; Nik Ghazali Nik Salleh; Mek Zah Salleh

    2016-01-01

    Hydrophobic coatings find wide application in industry due to their unique features such as water repellent and self-cleaning properties. In this study, modifying agent was synthesized by way of nano silica particles dispersion in polydimethyl siloxane with addition of surfactant, catalyst and stabilizer using high speed distemper. The modifying agent was added into coating formulation and cured under UV exposure. Scanning Electron Microscopy image of the film found that the nano silica particles were distributed well on substrate. Contact angle measurement gave the highest reading of 116 degree for 20 % wt of the modifying agent. The optical properties of the film were evaluated via transmission and haze test. (author)

  15. Osteoblast cell response to surface-modified carbon nanotubes

    International Nuclear Information System (INIS)

    Zhang Faming; Weidmann, Arne; Nebe, J. Barbara; Burkel, Eberhard

    2012-01-01

    In order to investigate the interaction of cells with modified multi-walled carbon nanotubes (MWCNTs) for their potential biomedical applications, the MWCNTs were chemically modified with carboxylic acid groups (–COOH), polyvinyl alcohol (PVA) polymer and biomimetic apatite on their surfaces. Additionally, human osteoblast MG-63 cells were cultured in the presence of the surface-modified MWCNTs. The metabolic activities of osteoblastic cells, cell proliferation properties, as well as cell morphology were studied. The surface modification of MWCNTs with biomimetic apatite exhibited a significant increase in the cell viability of osteoblasts, up to 67.23%. In the proliferation phases, there were many more cells in the biomimetic apatite-modified MWCNT samples than in the MWCNTs–COOH. There were no obvious changes in cell morphology in osteoblastic MG-63 cells cultured in the presence of these chemically-modified MWCNTs. The surface modification of MWCNTs with apatite achieves an effective enhancement of their biocompatibility.

  16. Pool boiling of nanoparticle-modified surface with interlaced wettability

    KAUST Repository

    Hsu, Chin-Chi

    2012-01-01

    This study investigated the pool boiling heat transfer under heating surfaces with various interlaced wettability. Nano-silica particles were used as the coating element to vary the interlaced wettability of the surface. The experimental results revealed that when the wettability of a surface is uniform, the critical heat flux increases with the more wettable surface; however, when the wettability of a surface is modified interlacedly, regardless of whether the modified region becomes more hydrophilic or hydrophobic, the critical heat flux is consistently higher than that of the isotropic surface. In addition, this study observed that critical heat flux was higher when the contact angle difference between the plain surface and the modified region was smaller. © 2012 Hsu et al.

  17. Antibacterial effect of silver nanofilm modified stainless steel surface

    Science.gov (United States)

    Fang, F.; Kennedy, J.; Dhillon, M.; Flint, S.

    2015-03-01

    Bacteria can attach to stainless steel surfaces, resulting in the colonization of the surface known as biofilms. The release of bacteria from biofilms can cause contamination of food such as dairy products in manufacturing plants. This study aimed to modify stainless steel surfaces with silver nanofilms and to examine the antibacterial effectiveness of the modified surface. Ion implantation was applied to produce silver nanofilms on stainless steel surfaces. 35 keV Ag ions were implanted with various fluences of 1 × 1015 to 1 × 1017 ions•cm-2 at room temperature. Representative atomic force microscopy characterizations of the modified stainless steel are presented. Rutherford backscattering spectrometry spectra revealed the implanted atoms were located in the near-surface region. Both unmodified and modified stainless steel coupons were then exposed to two types of bacteria, Pseudomonas fluorescens and Streptococcus thermophilus, to determine the effect of the surface modification on bacterial attachment and biofilm development. The silver modified coupon surface fluoresced red over most of the surface area implying that most bacteria on coupon surface were dead. This study indicates that the silver nanofilm fabricated by the ion implantation method is a promising way of reducing the attachment of bacteria and delay biofilm formation.

  18. Effects of bleaching agents on surface roughness of filling materials.

    Science.gov (United States)

    Markovic, Ljubisa; Jordan, Rainer Andreas; Glasser, Marie-Claire; Arnold, Wolfgang Hermann; Nebel, Jan; Tillmann, Wolfgang; Ostermann, Thomas; Zimmer, Stefan

    2014-01-01

    The aim of this study was to use a non-tactile optical measurement system to assess the effects of three bleaching agents' concentrations on the surface roughness of dental restoration materials. Two composites (Grandio, Venus) and one glass ionomer cement (Ketac Fil Plus) were used in this in vitro study. Specimens were treated with three different bleaching agents (16% and 22% carbamide peroxide (Polanight) and 38% hydrogen peroxide (Opalescence Boost)). Surface roughness was measured with an optical profilometer (Infinite Focus G3) before and after the bleaching treatment. Surface roughness increased in all tested specimens after bleaching treatment (p<0.05). Our in vitro study showed that dental bleaching agents influenced the surface roughness of different restoration materials, and the restoration material itself was shown to have an impact on alteration susceptibility. There seemed to be no clinical relevance in case of an optimal finish.

  19. Ammonia synthesis on Au modified Fe(111) and Ag and Cu modified Fe(100) surfaces

    DEFF Research Database (Denmark)

    Lytken, Ole; Waltenburg, Hanne Neergaard; Chorkendorff, Ib

    2003-01-01

    In order to investigate any influence of steps and possible positive effects of making surface alloys the ammonia synthesis has been investigated over Au modified Fe(111) and Ag and Cu modified Fe(100) single crystals in the temperature range 603-773 K, using a system combining ultra-high vacuum...... and a high-pressure cell. Ammonia was synthesized from a stoichiometric (N-2:3H(2)) gas mixture at a pressure of 2 bar. By deposition of small amounts of An, the ammonia production activity of the Fe(1 1 1) surface can be enhanced. More important, for the gold modified surface, the reaction order in ammonia...

  20. Adsorption of phospholipid bilayers onto pullulan-modified cellulose surfaces

    Science.gov (United States)

    Choi, Heejun; Liu, Zelin; Esker, Alan

    2009-03-01

    1,2-Dimyristoyl-sn-glycero-3-phosphocholine (DMPC) vesicle adsorption onto regenerated cellulose and pullulan 4-bromocinnamate (P4BC) modified cellulose surfaces was investigated via surface plasmon resonance (SPR) spectroscopy and quartz crystal microbalance with dissipation monitoring (QCM-D). P4BC with a degree of substitution (DS) of 0.061 ± 0.002 from UV measurements and 0.058 from ^1H NMR was synthesized from pullulan and 4-bromocinnamic acid to yield P4BC. The deduced thicknesses from SPR for DMPC layers were ˜3.7 nm (bilayer) on regenerated cellulose surfaces and ˜2.1 nm (monolayer) on P4BC modified cellulose surfaces. Qualitative analysis of the QCM-D data also indicated that the DMPC layers on P4BC modified cellulose surfaces were thinner than on regenerated cellulose surfaces.

  1. Silicalite-1 zeolite membranes on unmodified and modified surfaces

    Indian Academy of Sciences (India)

    Silicalite-1 zeolite membranes were prepared hydrothermally on the porous ceramic supports, both unmodified and modified with 3-aminopropyl triethoxysilane (APTES) as a coupling agent following ex situ (secondary) crystal growth process. The microstructure of the membranes was examined by scanning electron ...

  2. Evaluating the effect of different conditioning agents on the shear bond strength of resin-modified glass ionomers

    Directory of Open Access Journals (Sweden)

    Namith Rai

    2017-01-01

    Full Text Available Aim of the Study: This study aims to evaluate the effects three different conditioning agents on the shear bond strength of resin-modified glass ionomers to human dentin. Materials and Methods: One hundred and twenty recently extracted, caries-free premolars and molars will be cleaned of debris and disinfected in a 0.5% solution of sodium hypochlorite and sterile water for 30 min. The occlusal surface of each tooth will be reduced using conventional model trimmer with water to produce the dentin surface. Then, three different resin-modified glass ionomer cements (GICs were triturated and mixed according to the manufacturer's instructions, 10 specimens will be made of each group. The excess restorative material will be removed from matrix band dentin interface with a sharp number 25 bard parker blade. Samples were shear tested with Instron universal testing machine with a crosshead speed of 0.5 mm/min. A shearing bar beveled to a 1 mm thick contact surface area will be placed at the junction of dentin and plastic band matrix. The load required for the failure will be recorded in pounds and converted to megapascals. Results: Statistical analysis was done with analysis of variance and Tukey's test. Ketac primer as conditioning agent along with Fuji II LC as restorative material had the highest shear bond value whereas intact smear layer which was unmodified dentin had the least value. Conclusion: Within the limitations of the present study, it can be concluded that surface conditioning of dentin resulted significantly higher bond strength than unconditioned dentin surfaces. Clinical Significance: Resin-modified glass ionomers have several advantages compared to chemically cured GICs. The advantages include command cure, ease of handling, improved physical properties, and esthetics. Resin-modified glass ionomers have been marketed as direct restorative materials for Class V lesions as well as liners, bases, and luting agents. Several conditioning

  3. Improved efficiency of budesonide nebulization using surface-active agents

    NARCIS (Netherlands)

    Heijstra, M. P.; Schaefer, N. C.; Duiverman, E. J.; LeSouef, P. N.; Devadason, S. G.

    2006-01-01

    Our aim was to improve the efficiency of nebulised budesonide using surface-active agents. Cationic, anionic, and nonionic detergents were added to commercial budesonide suspension, and the particle size distribution during nebulization was measured using both cascade impaction and laser

  4. Effect of Material Composition on Cohesion Characteristics of Styrene-Butadiene-Styrene-Modified Asphalt Using Surface Free Energy

    Directory of Open Access Journals (Sweden)

    Xing-jun Zhang

    2017-01-01

    Full Text Available Styrene-butadiene-styrene- (SBS- modified asphalts were prepared by mixing different base asphalts, SBS modifier, extracting oil, and stabilizing agents. The contact angles between SBS-modified asphalt and distilled water, glycerol, and formamide were detected by the sessile drop method. Based on the surface energy theory, the surface free energy and cohesive power of SBS-modified asphalt were calculated. The influence of the raw materials composition, such as the virgin asphalt and SBS modifier types as well as the extracting oil and stabilizing agent contents, on the cohesive characteristics of SBS-modified asphalt was discussed. The results showed that virgin asphalt was compatible with SBS modifiers to improve cohesiveness. The cohesive power of branched SBS-modified asphalt was larger than that of linear SBS-modified asphalt. The cohesion of SBS-modified asphalt was improved as the SBS modifier and stabilizer contents increased but was reduced for excessive extraction oil contents. The cohesive characteristics of the SBS-modified asphalt were improved by the formation of stable three-dimensional network structures by cross-linking, winding, and grafting among different raw materials.

  5. Surface modification of self-healing poly(urea-formaldehyde) microcapsules using silane-coupling agent

    Energy Technology Data Exchange (ETDEWEB)

    Li Haiyan [Center for Composite Materials, Harbin Institute of Technology, Harbin 150001 (China)], E-mail: lhy06b@163.com; Wang Rongguo; Hu Honglin; Liu Wenbo [Center for Composite Materials, Harbin Institute of Technology, Harbin 150001 (China)

    2008-12-30

    Poly(urea-formaldehyde) (PUF) microcapsules, which are used as self-healing component of fibre reinforced resin matrix composites, were prepared by in situ polymerization method. The surface of PUF microcapsules was modified by using 3-aminopropyltriethoxy silane-coupling agent (KH550), and the interfacial interactions between PUF microcapsules and KH550 was also studied. Fourier transform infrared spectra (FT-IR) and X-ray photoelectron spectra (XPS) analyses showed that the silane-coupling agent molecular binds strongly to PUF microcapsules surface. Chemical bond (Si-O-C) was formed by the reaction between Si-OH and the hydroxyl group of PUF microcapsules, also there have chemical adsorption effect in the interface simultaneously because of the existence of hydrogen bond between Si-OH and the hydroxyl group of PUF microcapsules. Scanning electronic microscopy (SEM) observation showed that a thin layer was formed on the surface of modified PUF microcapsules. Additionally, fractured surface were observed under SEM to investigate the interfacial adhesion effect between PUF microcapsules and epoxy matrix. The result indicted that the silane-coupling agent play an important role in improving the interfacial performance between microcapsules and resin matrix.

  6. Surface modification of self-healing poly(urea-formaldehyde) microcapsules using silane-coupling agent

    Science.gov (United States)

    Li, Haiyan; Wang, Rongguo; Hu, Honglin; Liu, Wenbo

    2008-12-01

    Poly(urea-formaldehyde) (PUF) microcapsules, which are used as self-healing component of fibre reinforced resin matrix composites, were prepared by in situ polymerization method. The surface of PUF microcapsules was modified by using 3-aminopropyltriethoxy silane-coupling agent (KH550), and the interfacial interactions between PUF microcapsules and KH550 was also studied. Fourier transform infrared spectra (FT-IR) and X-ray photoelectron spectra (XPS) analyses showed that the silane-coupling agent molecular binds strongly to PUF microcapsules surface. Chemical bond (Si-O-C) was formed by the reaction between Si-OH and the hydroxyl group of PUF microcapsules, also there have chemical adsorption effect in the interface simultaneously because of the existence of hydrogen bond between Si-OH and the hydroxyl group of PUF microcapsules. Scanning electronic microscopy (SEM) observation showed that a thin layer was formed on the surface of modified PUF microcapsules. Additionally, fractured surface were observed under SEM to investigate the interfacial adhesion effect between PUF microcapsules and epoxy matrix. The result indicted that the silane-coupling agent play an important role in improving the interfacial performance between microcapsules and resin matrix.

  7. Polyimide modified with metal coupling agent for adhesion application

    Energy Technology Data Exchange (ETDEWEB)

    Tsai, Mei-Hui, E-mail: tsaimh@ncut.edu.t [Department of Chemical and Materials Engineering, National Chin-Yi University of Technology, Taichung 411, Taiwan (China); Lin, Yin-Kai [Department of Chemical and Materials Engineering, National Chin-Yi University of Technology, Taichung 411, Taiwan (China); Chang, Chi-Jung [Department of Chemical Engineering, Feng Chia University, Taichung 407, Taiwan (China); Chiang, Pei-Chun [Department of Materials Science and Engineering, Mingdao University, Changhua 523, Taiwan (China); Yeh, Jui-Ming [Department of Chemistry and Center for Nanotechnology, Chung-Yuan Christian University, Chung Li 320, Taiwan (China); Chiu, Wei-Ming; Huang, Shih-Liang; Ni, Sheng-Chung [Department of Chemical and Materials Engineering, National Chin-Yi University of Technology, Taichung 411, Taiwan (China)

    2009-07-01

    Polyimide hybrid metal oxide thin films used on flexible print circuit boards are prepared by the in situ sol-gel process. The precursor, poly (amic acid), containing 2,2'-bis[4-(4-aminophenoxy) phenyl]propane (p-BAPP), 3,3',4,4'-benzophenetetraacarboxylic anhydride (BTDA) and p-aminopropyltrimetoxysilane (APrTMOS), is synthesized, and then phenyltrimethoxysilane; PhSi(OCH{sub 3}){sub 3} and tris(2,4-pentanedionatio) aluminum(III); Al(C{sub 5}H{sub 7}O{sub 2}){sub 3} are added and mixed thoroughly. Following curing, the polyimide/PhSiOx/Al{sub 2}O{sub 3} hybrid films exhibit high transparency and flexibility. The adhesion improvement between copper and polyimides hybrid films is investigated by peel test and the X-ray photoelectron spectroscopy (XPS) measurements are made to demonstrate that the Si elements from APrTMOS and PhSiOx migrate from the surface to the bulk of polyimide hybrids. Dynamic mechanical analysis (DMA) indicates that the glass transition temperature (Tg) increases with the Al{sub 2}O{sub 3} content and the tan{delta} peak becomes broader and lower. The nano-sized Al{sub 2}O{sub 3} particles are highly dispersed in the hybrid film, as detected by high-resolution transmission electron microscopy (HRTEM). The polyimide/PhSiOx/Al{sub 2}O{sub 3} films show good peel strength with copper, as well as high Tg values. They may therefore have potential applications in flexible print circuits.

  8. Screening for new surface washing agents and mechanisms of action

    International Nuclear Information System (INIS)

    Zhang, Y.; Liu, H.

    1997-01-01

    Surface washing agents (SWAs) for oil spills were screened using the inclined through method developed by Environment Canada. There are two categories of SWAs, i.e. non-surfactant based solvents, and surface active agents (surfactants). Results showed that among the SWAs tested, the systems based on a normal alkane solvent, including POD20, BOD123, and BOD124, had the best performance and the lowest toxicity. The optimum hydrophilic/lipophilic (HLB) value of hydrocarbon-based SWAs was found to fall in the range of 11 and 13, which is the HLB range between dispersants and detergents. The importance of reducing the interfacial tension between oil and water, and of making solid substrate surface water-wettable was also identified. The use of low-concentration aqueous surfactant solutions as rinsing water was found to improve effectiveness under field conditions. 10 refs., 21 figs

  9. AFM surface morphology investigation of ion beam modified polyimide

    Science.gov (United States)

    Švorčík, V.; Arenholz, E.; Rybka, V.; Hnatowicz, V.

    1997-03-01

    Polyimide Upilex R was irradiated with 90 keV N + ions to the fluences of 1 × 10 14-2 × 10 17 cm -2. The surface morphology and the structure of the ion beam modified PI were examined using atomic force microscopy and X-ray difraction. Sheet resistance as a function of the ion fluence and the sample temperature was measured by standard two point technique. Significant changes of the surface morphology and production of graphitic phase in the sample surface layer modified by the ion irradiation were observed. Strong decrease of the sheet resistance (by 11 orders of magnitude) in the ion beam modified samples is connected with progressive carbonization and graphitization of the degraded polymer. Electrical charge transport is mediated by variable-range hopping mechanism. Drastic structural changes initiated by the ion irradiation to high fluences are similar to those observed in polymer pyrolysis.

  10. Inhibition of Sulfide Mineral Oxidation by Surface Coating Agents: Batch

    Science.gov (United States)

    Choi, J.; Ji, M. K.; Yun, H. S.; Park, Y. T.; Gee, E. D.; Lee, W. R.; Jeon, B.-H.

    2012-04-01

    Mining activities and mineral industries have impacted on rapid oxidation of sulfide minerals such as pyrite (FeS2) which leads to Acid Mine Drainage (AMD) formation. Some of the abandoned mines discharge polluted water without proper environmental remediation treatments, largely because of financial constraints in treating AMD. Magnitude of the problem is considerable, especially in countries with a long history of mining. As metal sulfides become oxidized during mining activities, the aqueous environment becomes acid and rich in many metals, including iron, lead, mercury, arsenic and many others. The toxic heavy metals are responsible for the environmental deterioration of stream, groundwater and soils. Several strategies to remediate AMD contaminated sites have been proposed. Among the source inhibition and prevention technologies, microencapsulation (coating) has been considered as a promising technology. The encapsulation is based on inhibition of O2 diffusion by surface coating agent and is expected to control the oxidation of pyrite for a long time. Potential of several surface coating agents for preventing oxidation of metal sulfide minerals from both Young-Dong coal mine and Il-Gwang gold mine were examined by conducting batch experiments and field tests. Powdered pyrite as a standard sulfide mineral and rock samples from two mine outcrops were mixed with six coating agents (KH2PO4, MgO and KMnO4 as chemical agents, and apatite, cement and manganite as mineral agents) and incubated with oxidizing agents (H2O2 or NaClO). Batch experiments with Young-Dong coal mine samples showed least SO42- production in presence of KMnO4 (16% sulfate production compared to no surface coating agents) or cement (4%) within 8 days. In the case of Il-Gwang mine samples, least SO42- production was observed in presence of KH2PO4 (8%) or cement (2%) within 8 days. Field-scale pilot tests at Il-Gwang site also showed that addition of KH2PO4 decreased sulfate production from 200 to

  11. Corrosion resistance of surface modified nickel titanium archwires.

    Science.gov (United States)

    Krishnan, Manu; Seema, Saraswathy; Kumar, A Vinod; Varthini, N Parvatha; Sukumaran, Kalathil; Pawar, Vasant R; Arora, Vimal

    2014-03-01

    To compare the corrosion behavior of commercially available surface modified nickel titanium (NiTi) arch wires with respect to a conventional NiTi and to evaluate its association with surface characteristics. Five types of surface modified arch wires and a conventional NiTi arch wire, all from different manufacturers, were evaluated for their corrosion resistance from breakdown potential in an anodic polarization scan in Ringer's solution. Surface characteristics were determined from scanning electron microscopy, atomic force microscopy, and energy dispersive analysis. One-way analysis of variance and post hoc Duncan's multiple range tests were used to evaluate statistical significance. Surface modified NiTi wires showed significant improvement in corrosion resistance and reduction in surface roughness values. Breakdown potentials increased in the order of group 6 (conventional; 204 mV) corrosion resistance and decreasing surface roughness. However, neither factor could maintain a direct, one-to-one relationship. It meant that the type and nature of coating material can effectively influence the anticorrosive features of NiTi wires, compared with its surface roughness values.

  12. Eutrophication management in surface waters using lanthanum modified bentonite

    DEFF Research Database (Denmark)

    Copetti, Diego; Finsterle, Karin; Marziali, Laura

    2016-01-01

    This paper reviews the scientific knowledge on the use of a lanthanum modified bentonite (LMB) to manage eutrophication in surface water. The LMB has been applied in around 200 environments worldwide and it has undergone extensive testing at laboratory, mesocosm, and whole lake scales. The availa......This paper reviews the scientific knowledge on the use of a lanthanum modified bentonite (LMB) to manage eutrophication in surface water. The LMB has been applied in around 200 environments worldwide and it has undergone extensive testing at laboratory, mesocosm, and whole lake scales...

  13. Comparative evaluation of bond strength of all-metal crowns with different luting agents after undergoing various modes of surface treatments: An in-vitro study

    Directory of Open Access Journals (Sweden)

    Shivam Singh Tomar

    2015-01-01

    Conclusion: Among all types of surface treatments used in this study, maximum bond strength was yielded by sandblasting with 110 µm alumina + ultrasonic cleaning and the best luting agent was resin-modified glass ionomer cement.

  14. Surface agents' influence on the flexural strength of bilaminated ceramics

    Directory of Open Access Journals (Sweden)

    Julia Magalhaes Costa Lima

    2013-07-01

    Full Text Available The objective of this study was to evaluate the influence of different surface agents on the flexural strength of a ceramic system. Eighty bar-shaped specimens of zirconia were divided into four groups according to the agent to be used: group Control - to be cleaned with alcohol; group VM9 - application of a fluid layer of porcelain; group Effect Bonder - application of a bonding agent; and group Coloring Liquid - application of coloring liquid. All specimens received the porcelain application by the layering technique and were then subjected to thermocycling. The four-point bending test was performed to calculate the strength values (σ, MPa and the failure modes were classified. ANOVA did not detect significant differences among the groups. The Weibull modulus were 5 (Control, VM9 and Effect Bonder and 6 (Coloring Liquid. The cracking of the porcelain ceramic toward the interface was the predominant failure mode. It was concluded that the surface agents tested had no effect on the flexural strength of the bilaminated ceramic specimens.

  15. Silicalite-1 zeolite membranes on unmodified and modified surfaces ...

    Indian Academy of Sciences (India)

    Administrator

    (Algieri et al 2003). However, a higher value i.e. 20 × 10. –7 mol m. –2 s. –1. Pa. –1 of N2 permeance was found for the membrane prepared on the unmodified support surface. It indicates that the membrane prepared by surface modifi- cation technique has higher interlocking of the crystals and hence a lower degree of ...

  16. Silicalite-1 zeolite membranes on unmodified and modified surfaces ...

    Indian Academy of Sciences (India)

    Administrator

    support was observed resulting in a relatively higher dense packing of the crystals during secondary crystal growth process compared to that obtained from the unmodified support. The membrane developed on surface modified support rendered lower permeance value i.e. 9 × 10. –7 mol m. –2 s. –1. Pa. –1 of N2 compared ...

  17. Listeria monocytogenes repellence by enzymatically modified PES surfaces

    NARCIS (Netherlands)

    Veen, van der S.; Nady, N.; Franssen, M.C.R.; Zuilhof, H.; Boom, R.M.; Abee, T.; Schroën, C.G.P.H.

    2015-01-01

    : The effect of enzyme-catalyzed modification of poly(ethersulfone) (PES) on the adhesion and biofilm formation of two Listeria monocytogenes strains is evaluated under static and dynamic flow conditions. PES has been modified with gallic acid, ferulic acid and 4-hydroxybenzoic acid. The surfaces

  18. Surface-modified magnetic nanoparticles for cell labeling

    Czech Academy of Sciences Publication Activity Database

    Zasońska, Beata Anna; Patsula, Vitalii; Stoika, R.; Horák, Daniel

    2014-01-01

    Roč. 13, č. 4 (2014), s. 63-73 ISSN 2305-7815 R&D Projects: GA MŠk(CZ) LH14318 Institutional support: RVO:61389013 Keywords : magnetic nanoparticles * surface-modified * cell labeling Subject RIV: CD - Macromolecular Chemistry

  19. Implication of surface modified NZVI particle retention in the porous ...

    Indian Academy of Sciences (India)

    Retention of surface-modified nanoscale zero-valent iron (NZVI) particles in the porous media near the point of injection has been reported in the recent studies. Retention of excess particles in porous media can alter the media properties. The main objectives of this study are, therefore, to evaluate the effect of particle ...

  20. Efficiency of surface modified Ti coated with copper nanoparticles to ...

    Indian Academy of Sciences (India)

    various fields like medical instruments and devices, water treatment and food processing. For better utilization of antimicrobial activity the metal nanoparticles may be com- bined with polymers to form composites [23]. Our pre- vious study also proved the anti-biofouling property of surface modified Ti coated with silver ...

  1. Enhanced biofouling resistance of polyethersulfone membrane surface modified with capsaicin derivative and itaconic acid

    International Nuclear Information System (INIS)

    Wang, Jian; Gao, Xueli; Wang, Qun; Sun, Haijing; Wang, Xiaojuan; Gao, Congjie

    2015-01-01

    Graphical abstract: - Highlights: • PES membrane was modified with a capsaicin derivative. • UV-assisted graft polymerization was carried out on membrane surface. • The capsaicin derivative modified membrane shows better antibiofouling property. - Abstract: The culprit of biofouling is the reproduction of viable microorganisms on the membrane surface. Recently, functionalization of membrane surface with natural antibacterial agents has drawn great attention. This work presents the fabrication of antibiofouling polyethersulfone (PES) ultrafiltration (UF) membranes by UV-assisted photo grafting of capsaicin derivative (N-(4-hydroxy-3-methoxy-benzyl)-acrylamide, HMBA) and itaconic acid (IA) on the surface of PES membrane. Results of FTIR-ATR, water static contact angle (WSCA) and atomic force microscopy (AFM) analysis confirmed the successful grafting of HMBA and IA on the membrane surface. We investigated the antifouling and antibacterial properties of these membranes using BSA and Escherichia coli as the test model, respectively. During a 150-min test, the modified membranes show much lower flux decline (42.7% for PES-g-1H0I, 22.2% for PES-g-1H1I and 7.7% for PES-g-1H5I) when compared with the pristine membrane (flux declined by 77%). The modified membranes exhibit excellent antibacterial activity (nearly 100%) when UV irradiation time was 6 min. The morphological study suggested that the E. coli on the pristine membrane showed a regular and smooth surface while that on the modified membrane was disrupted, which validated the antibacterial activity of the modified membranes.

  2. Enhanced biofouling resistance of polyethersulfone membrane surface modified with capsaicin derivative and itaconic acid

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Jian [Key Laboratory of Marine Chemistry Theory and Technology, Ministry of Education, Ocean University of China, Qingdao 266100 (China); College of Chemistry and Chemical Engineering, Ocean University of China, Qingdao 266100 (China); Gao, Xueli, E-mail: gxl_ouc@126.com [Key Laboratory of Marine Chemistry Theory and Technology, Ministry of Education, Ocean University of China, Qingdao 266100 (China); College of Chemistry and Chemical Engineering, Ocean University of China, Qingdao 266100 (China); Wang, Qun; Sun, Haijing; Wang, Xiaojuan [Key Laboratory of Marine Chemistry Theory and Technology, Ministry of Education, Ocean University of China, Qingdao 266100 (China); College of Chemistry and Chemical Engineering, Ocean University of China, Qingdao 266100 (China); Gao, Congjie, E-mail: gaocjie@ouc.edu.cn [Key Laboratory of Marine Chemistry Theory and Technology, Ministry of Education, Ocean University of China, Qingdao 266100 (China); College of Chemistry and Chemical Engineering, Ocean University of China, Qingdao 266100 (China)

    2015-11-30

    Graphical abstract: - Highlights: • PES membrane was modified with a capsaicin derivative. • UV-assisted graft polymerization was carried out on membrane surface. • The capsaicin derivative modified membrane shows better antibiofouling property. - Abstract: The culprit of biofouling is the reproduction of viable microorganisms on the membrane surface. Recently, functionalization of membrane surface with natural antibacterial agents has drawn great attention. This work presents the fabrication of antibiofouling polyethersulfone (PES) ultrafiltration (UF) membranes by UV-assisted photo grafting of capsaicin derivative (N-(4-hydroxy-3-methoxy-benzyl)-acrylamide, HMBA) and itaconic acid (IA) on the surface of PES membrane. Results of FTIR-ATR, water static contact angle (WSCA) and atomic force microscopy (AFM) analysis confirmed the successful grafting of HMBA and IA on the membrane surface. We investigated the antifouling and antibacterial properties of these membranes using BSA and Escherichia coli as the test model, respectively. During a 150-min test, the modified membranes show much lower flux decline (42.7% for PES-g-1H0I, 22.2% for PES-g-1H1I and 7.7% for PES-g-1H5I) when compared with the pristine membrane (flux declined by 77%). The modified membranes exhibit excellent antibacterial activity (nearly 100%) when UV irradiation time was 6 min. The morphological study suggested that the E. coli on the pristine membrane showed a regular and smooth surface while that on the modified membrane was disrupted, which validated the antibacterial activity of the modified membranes.

  3. Microstructure and electrochemical behavior of cerium conversion coating modified with silane agent on magnesium substrates

    Energy Technology Data Exchange (ETDEWEB)

    Lei, Li; Shi, Jing, E-mail: shijing@ouc.edu.cn; Wang, Xin, E-mail: wangxin.hd@163.com; Liu, Dan; Xu, Haigang

    2016-07-15

    Graphical abstract: The unmodified coating shows averaged static water contact angles of a little more than 50º, which is clearly hydrophilic for water solutions. With the silane concentration increases, the water contact angles show an increase tendency. Especially, when the silane addition is increased to 25 ml L-1, the coating surface presents a hydrophobic feature, with static water contact angle of more than 110º. - Highlights: • BTESPT modification can effectively improve the uniformity, hydrophobic performance, chemical stability and corrosion inhibition capability of traditional cerium conversion coating. • Si-O-Si linkage builds a robust structure to increase of the coating density. Si−O−Mg bonds strengthen the adhesion between the coating/substrate. • The system modified with 25 ml L{sup −1} BTESPT displays the optimum corrosion protection performance. - Abstract: The cerium conversion coating with and without different concentrations of silane agent bis-(γ-triethoxysilylpropyl)-tetrasulfide (BTESPT) modification is obtained on magnesium alloys. Detailed properties of the coatings and the role of BTESPT as an additive are studied and followed with careful discussion. The coating morphology, wettability, chemical composition and corrosion resistance are characterized by scanning electronic microscope (SEM), water contact-angle, X-ray photoelectron spectroscopy (XPS), potentiodynamic measurements and electrochemical impedance spectroscopy (EIS). The electrochemical behavior of the coatings is investigated using EIS. The results indicate that the coating morphology and composition can be controlled by changing silane concentration. The combination of cerium ions and silane molecules could promote the formation of more homogenous and higher hydrophobic coating. The coating turns to be more compact and the adhesive strength between the coating and the magnesium substrate are strongly improved with the formation of Si−O−Si and Si

  4. ELECTROCATALYSIS ON SURFACES MODIFIED BY METAL MONOLAYERS DEPOSITED AT UNDERPOTENTIALS.

    Energy Technology Data Exchange (ETDEWEB)

    ADZIC,R.

    2000-12-01

    The remarkable catalytic properties of electrode surfaces modified by monolayer amounts of metal adatoms obtained by underpotential deposition (UPD) have been the subject of a large number of studies during the last couple of decades. This interest stems from the possibility of implementing strictly surface modifications of electrocatalysts in an elegant, well-controlled way, and these bi-metallic surfaces can serve as models for the design of new catalysts. In addition, some of these systems may have potential for practical applications. The UPD of metals, which in general involves the deposition of up to a monolayer of metal on a foreign substrate at potentials positive to the reversible thermodynamic potential, facilitates this type of surface modification, which can be performed repeatedly by potential control. Recent studies of these surfaces and their catalytic properties by new in situ surface structure sensitive techniques have greatly improved the understanding of these systems.

  5. Optimized surface topography of thermoplastics blends modified by graphene

    Energy Technology Data Exchange (ETDEWEB)

    Joshi, Girish M., E-mail: varadgm@gmail.com, E-mail: girish.joshi@vit.ac.in; Sharma, Ajay; Pandey, Mayank; Khutia, Moumita [Polymer Nanocomposite Laboratory, Material Physics Division, School of Advanced Sciences, VIT University, Vellore-632014,Tamilnadu (India); Rao, N. Madhusudhana; Kaleemulla, S. [Thinfilm Laboratory, Material Physics Division, School of Advanced Sciences, VIT University, Vellore-632014,Tamilnadu (India); Kumar, Ramesh C. [Thermal and Automotive Division, School of Mechanical and Building Sciences, VIT University, Vellore-632014,Tamilnadu (India); Deshmukh, R. R. [Laboratory of Nanotechnology, University of Castilla-La Mancha, Plaza Manuel Meca 1, 13400 Almadén (Spain); Cuberes, M. Teresa [Department of Physics, Institute of Chemical Technology, Matunga, Mumbai-400 019 (India)

    2016-05-23

    Polyacrilonitrile (PAN)/ Polyvinylfloride (PVDF) blends were modified by loading the graphene (0.5 to 1.5 wt %). The presence of graphene reveals the interesting surface properties. The decrease in surface roughness as function of graphene loading was confirmed by the topographic method of recording (two and three dimensional images) with atomic force microscope (AFM). The blends become smoother in nature due to occupied smaller surface area of graphene. This property may be useful for several applications in the marine, naval, nuclear domain and engineering applications as barrier medium.

  6. Surface modification of cured cement pastes by silane coupling agents.

    Science.gov (United States)

    Stewart, Andrew; Schlosser, Brett; Douglas, Elliot P

    2013-02-01

    X-ray photoelectron spectroscopy (XPS) and static contact angle measurements were used to study the interaction between silane coupling agents and cured cement paste. Three different silane coupling agents were investigated: aminopropyltriethoxy silane (APTES), 3-glycidyloxypropyltrimethoxy silane (GPTMS), and methoxy-terminated polydimethxyl siloxane (PDMS). These silanes have different end groups, so the change in surface energy after undergoing a successful reaction between the silane and hydroxyls on the surface of the cement paste was demonstrated by a change in contact angle. Relative to untreated samples, APTES samples decreased the contact angle, PDMS samples increased the contact angle, and GPTMS did not show a significant change in contact angle. Samples with a water-to-cement ratio (w/c) of 0.5 showed a larger change in contact angle than 0.4 w/c ratio samples, because of a greater number of hydroxyl groups at the surface. Deconvolution of the O 1s and Si 2p XPS peaks were performed to determine contributions from bridging and nonbridging atoms. An increase in bridging silicon and oxygen atoms relative to untreated samples indicated successful silane condensation and that a covalent bond was formed between the cement paste and silanes.

  7. Perspective of surface active agents in baking industry: an overview.

    Science.gov (United States)

    Ahmad, Asif; Arshad, Nazish; Ahmed, Zaheer; Bhatti, Muhammad Shahbaz; Zahoor, Tahir; Anjum, Nomana; Ahmad, Hajra; Afreen, Asma

    2014-01-01

    Different researchers have previously used surfactants for improving bread qualities and revealed that these compounds result in improving the quality of dough and bread by influencing dough strength, tolerance, uniform crumb cell size, and improve slicing characteristics and gas retention. The objective of this review is to highlight the areas where surfactants are most widely used particularly in the bread industries, their role and mechanism of interaction and their contribution to the quality characteristics of the dough and bread. This review reveals some aspects of surface-active agents regarding its role physiochemical properties of dough that in turn affect the bread characteristics by improving its sensory quality and storage stability.

  8. Molluscicidal properties and selective toxicity of surface-active agents

    Science.gov (United States)

    Visser, S. A.

    1965-01-01

    Of over 100 commercially produced surface-active agents tested against the bilharziasis vector snail Biomphalaria sudanica, 13 were found to possess considerable and highly selective molluscicidal properties at concentrations of less than 1 ppm for exposures of 48 hours. Against crustacea, fish, water plants, mosquito larvae, mice, and the eggs of B. sudanica, the toxicities of the 13 surfactants were slight. The chemicals did not appear to be absorbed by organic matter to any appreciable extent. It is thought that the toxicity to B. sudanica is of both a chemical and a physical nature. PMID:5294185

  9. Isolation, screening, and characterization of surface-active agent-producing, oil-degrading marine bacteria of Mumbai Harbor.

    Science.gov (United States)

    Mohanram, Rajamani; Jagtap, Chandrakant; Kumar, Pradeep

    2016-04-15

    Diverse marine bacterial species predominantly found in oil-polluted seawater produce diverse surface-active agents. Surface-active agents produced by bacteria are classified into two groups based on their molecular weights, namely biosurfactants and bioemulsifiers. In this study, surface-active agent-producing, oil-degrading marine bacteria were isolated using a modified Bushnell-Haas medium with high-speed diesel as a carbon source from three oil-polluted sites of Mumbai Harbor. Surface-active agent-producing bacterial strains were screened using nine widely used methods. The nineteen bacterial strains showed positive results for more than four surface-active agent screening methods; further, these strains were characterized using biochemical and nucleic acid sequencing methods. Based on the results, the organisms belonged to the genera Acinetobacter, Alcanivorax, Bacillus, Comamonas, Chryseomicrobium, Halomonas, Marinobacter, Nesterenkonia, Pseudomonas, and Serratia. The present study confirmed the prevalence of surface-active agent-producing bacteria in the oil-polluted waters of Mumbai Harbor. Copyright © 2016 Elsevier Ltd. All rights reserved.

  10. Bond Strength of Composite to Dentin using Resin-Modified Glass Ionomers as Bonding Agents

    Science.gov (United States)

    2016-03-02

    Vandewalle, Kraig Civ 59 DTS/ 59 DG/ SGDTG WHASC f. 9 h. I I 1 CERTIFY ANY HUMAN OR ANIMAL RESEARCH RELATED STUDIES WERE APPROVED AND PERFORMED IN STRICT...strength of composite to dentin using resin-modified glass ionomers (RMGI) as bonding agents. Methods: Sixty extracted human third molars were...59 MDW/SGVU SUBJECT: Professional Presentation Approval 2 MAR 20 16 l. Your paper, entitl ed Bond Strength of Composite to Dentin using Resin

  11. Osteogenic potential of laser modified and conditioned titanium zirconium surfaces

    Directory of Open Access Journals (Sweden)

    P David Charles

    2016-01-01

    Full Text Available Statement of Problem: The osseointegration of dental implant is related to their composition and surface treatment. Titanium zirconium (TiZr has been introduced as an alternative to the commercially pure titanium and its alloys as dental implant material, which is attributed to its superior mechanical and biological properties. Surface treatments of TiZr have been introduced to enhance their osseointegration ability; however, reliable, easy to use surface modification technique has not been established. Purpose: The purpose of this study was to evaluate and compare the effect of neodymium-doped yttrium aluminum garnet (Nd-YAG laser surface treatment of TiZr implant alloy on their osteogenic potential. Materials and Methods: Twenty disc-shaped samples of 5 mm diameter and 2 mm height were milled from the TiZr alloy ingot. The polished discs were ultrasonically cleaned in distilled water. Ten samples each were randomly selected as Group A control samples and Group B consisted of Nd-YAG laser surface etched and conditioned test samples. These were evaluated for cellular response. Cellular adhesion and proliferation were quantified, and the results were statistically analyzed using nonparametric analysis. Cellular morphology was observed using electron and epiflurosence microscopy. Results: Nd-YAG laser surface modified and conditioned TiZr samples increased the osteogenic potential. Conclusion: Nd-YAG laser surface modification of TiZr, improves the cellular activity, surface roughness, and wettability, thereby increasing the osteogenic potential.

  12. Surface modified carbon nanoparticle papers and applications on polymer composites

    Science.gov (United States)

    Ouyang, Xilian

    Free-standing paper like materials are usually employed as protective layers, chemical filters, components of electrical batteries or supercapacitors, adhesive layers, and electronic or optoelectric components. Free-standing papers made from carbon nanoparticles have drawn increased interest because they have a variety of superior chemical and physical characteristics, such as light weight, high intrinsic mechanical properties, and extraordinary high electrical conductivity. Nanopapers fabricated from 1- D shape carbon nanofibers (CNFs) and carbon nanotubes (CNTs) are promising reinforcing materials for polymer composites, because the highly porous CNF and CNT nanopapers (porosity ˜80% and ˜70% respectively) can be impregnated with matrix polymers. In the first part of this work, polyaniline (PANI) was used to functionalize the surface of CNFs, and the resultant carbon nanopapers presented impressive mechanical strength and electrical conductivity that it could be used in the in-mold coating (IMC)/ injection molding process to achieve high electromagnetic interference (EMI) shielding effectiveness. Aniline modified (AF) CNT nanopapers were used as a 3D network in gas separation membranes. The resultant composite membranes demonstrated better and stable CO2 permeance and CO 2/H2 selectivity in a high temperature (107°C) and high pressure (15-30 atm) gas separation process, not achievable by conventional polymer membranes. In the second part, we demonstrated that 2-D graphene (GP) or graphene oxide (GO) nanosheets could be tightly packed into a film which was impermeable to most gases and liquids. GP or GO nanopapers could be coated on polymer composites. In order to achieve well-dispersed single-layer graphene in aqueous medium, we developed a facile approach to synthesize functional GP bearing benzenesulfonic acid groups which allow the preparation of nanopapers by water based assembly. With the optimized processing conditions, our best GP nanopapers could reach

  13. Characterization of polymer-modified cement as a solidification agent for the radwaste

    International Nuclear Information System (INIS)

    Ji, Young-Yong; Kwak, Kyung-Kil; Hong, Dae-Seok; Ryu, Woo-Seog

    2012-01-01

    Highlights: ► Polymer-modified cement (PMC) by modification with water-based resins. ► Determination of the optimized polymer content. ► Evaluation of the improved chemical resistance of the PMC. ► Decrease of the amount of ions released into the demineralized water. ► Highly improved property for the nuclide diffusivity at the Co-60. - Abstract: Polymer-modified cement can be produced by partially replacing cement hydrate binders in ordinary Portland cement with polymeric compounds. It is known that the addition of the polymer to the cement paste leads to improved quality, which would be expected to have a high chemical resistance. In order to investigate the application as a solidification agent for the radwaste, polymer-modified cement specimens, by modification with water-based resins, were prepared according to the polymer content from 0% to 30%. The optimized polymer content in the cement pastes was then determined through the compressive strength and the porosity test. Finally, the improved chemical resistance of the polymer-modified cement with the optimized polymer content was evaluated by the thermal cycling, the immersion, and the leaching tests. From the test results, the amount of ions released into the water showed lower values of about 20% at the polymer-modified cement. Especially, a highly improved nuclide diffusivity of Co-60 was observed in the polymer-modified cement.

  14. Synthesis and Evaluation of Zeolite Surface-Modified Perlite

    Directory of Open Access Journals (Sweden)

    Kasai Makoto

    2017-01-01

    Full Text Available Perlite is volcanic glass mainly composed of amorphous aluminum silicate, mainly composed SiO2 and Al2O3 with less impurities such as heavy metals. Amorphous (glassy perlite is used in lightweight aggregate and insulation. In addition, it has also been used as a filter aid by grinding the expanded perlite. However, it has not been used as environmental cleanup materials, because the ion exchange capacity of the perlite is very low. In this study, we tried to synthesize the hybrid filter aid with chemical adsorption capacity by synthesizing the zeolite on the surface of the perlite. As a result, by using the hydrothermal synthesis method, zeolite surface modified perlite was synthesized in which the LTA type zeolites were generated on the surface of the perlite.

  15. Porous surface modified bioactive bone cement for enhanced bone bonding.

    Directory of Open Access Journals (Sweden)

    Qiang He

    Full Text Available Polymethylmethacrylate bone cement cannot provide an adhesive chemical bonding to form a stable cement-bone interface. Bioactive bone cements show bone bonding ability, but their clinical application is limited because bone resorption is observed after implantation. Porous polymethylmethacrylate can be achieved with the addition of carboxymethylcellulose, alginate and gelatin microparticles to promote bone ingrowth, but the mechanical properties are too low to be used in orthopedic applications. Bone ingrowth into cement could decrease the possibility of bone resorption and promote the formation of a stable interface. However, scarce literature is reported on bioactive bone cements that allow bone ingrowth. In this paper, we reported a porous surface modified bioactive bone cement with desired mechanical properties, which could allow for bone ingrowth.The porous surface modified bioactive bone cement was evaluated to determine its handling characteristics, mechanical properties and behavior in a simulated body fluid. The in vitro cellular responses of the samples were also investigated in terms of cell attachment, proliferation, and osteoblastic differentiation. Furthermore, bone ingrowth was examined in a rabbit femoral condyle defect model by using micro-CT imaging and histological analysis. The strength of the implant-bone interface was also investigated by push-out tests.The modified bone cement with a low content of bioactive fillers resulted in proper handling characteristics and adequate mechanical properties, but slightly affected its bioactivity. Moreover, the degree of attachment, proliferation and osteogenic differentiation of preosteoblast cells was also increased. The results of the push-out test revealed that higher interfacial bonding strength was achieved with the modified bone cement because of the formation of the apatite layer and the osseointegration after implantation in the bony defect.Our findings suggested a new bioactive

  16. Improved efficiency of budesonide nebulization using surface-active agents.

    Science.gov (United States)

    Bouwman, A M; Heijstra, M P; Schaefer, N C; Duiverman, E J; Lesouëf, P N; Devadason, S G

    2006-01-01

    Our aim was to improve the efficiency of nebulised budesonide using surface-active agents. Cationic, anionic, and nonionic detergents were added to commercial budesonide suspension, and the particle size distribution during nebulization was measured using both cascade impaction and laser diffraction. Our results showed that the emitted dose was increased after addition of cationic (p < 0.001) and nonionic detergents (p < 0.01) compared with the commercial formulation alone. The respirable fraction was increased for all detergent formulations (p < 0.001) compared with the commercial formulation. We concluded that cationic and nonionic detergent increased the total output of budesonide from the Sidestream. All detergent formulations increased the respirable fraction of nebulized budesonide.

  17. Modified Critical State Two-Surface Plasticity Model for Sands

    DEFF Research Database (Denmark)

    Sørensen, Kris Wessel; Nielsen, Søren Kjær; Shajarati, Amir

    This article describes the outline of a numerical integration scheme for a critical state two-surface plasticity model for sands. The model is slightly modified by LeBlanc (2008) compared to the original formulation presented by Manzari and Dafalias (1997) and has the ability to correctly model...... the stress-strain response of sands. The model is versatile and can be used to simulate drained and undrained conditions, due to the fact that the model can efficiently calculate change in void ratio as well as pore pressure. The objective of the constitutive model is to investigate if the numerical...

  18. Development of a Modified Vacuum Cleaner for Lunar Surface Systems

    Science.gov (United States)

    Toon, Katherine P.; Lee, Steve A.; Edgerly, Rachel D.

    2010-01-01

    The National Aeronautics and Space Administration (NASA) mission to expand space exploration will return humans to the Moon with the goal of maintaining a long-term presence. One challenge that NASA will face returning to the Moon is managing the lunar regolith found on the Moon's surface, which will collect on extravehicular activity (EVA) suits and other equipment. Based on the Apollo experience, the issues astronauts encountered with lunar regolith included eye/lung irritation, and various hardware failures (seals, screw threads, electrical connectors and fabric contamination), which were all related to inadequate lunar regolith mitigation. A vacuum cleaner capable of detaching, transferring, and efficiently capturing lunar regolith has been proposed as a method to mitigate the lunar regolith problem in the habitable environment on lunar surface. In order to develop this vacuum, a modified "off-the-shelf' vacuum cleaner will be used to determine detachment efficiency, vacuum requirements, and optimal cleaning techniques to ensure efficient dust removal in habitable lunar surfaces, EVA spacesuits, and air exchange volume. During the initial development of the Lunar Surface System vacuum cleaner, systematic testing was performed with varying flow rates on multiple surfaces (fabrics and metallics), atmospheric (14.7 psia) and reduced pressures (10.2 and 8.3 psia), different vacuum tool attachments, and several vacuum cleaning techniques in order to determine the performance requirements for the vacuum cleaner. The data recorded during testing was evaluated by calculating particulate removal, relative to the retained simulant on the tested surface. In addition, optical microscopy was used to determine particle size distribution retained on the surface. The scope of this paper is to explain the initial phase of vacuum cleaner development, including historical Apollo mission data, current state-of-the-art vacuum cleaner technology, and vacuum cleaner testing that has

  19. Synthesis of modified pyridine and bipyridine substituted coumarins as potent antimicrobial agents

    Directory of Open Access Journals (Sweden)

    Lad Hemali B.

    2015-01-01

    Full Text Available In search for new antimicrobial agents a series of new modified pyridine and bipyridine substituted coumarins 5a-y was designed and synthesized by adopting molecular hybridization strategy. All the synthesized compounds were evaluated for their in vitro antimicrobial activity using broth dilution method against selected bacterial (Gram-positive and Gram-negative and fungal strains. Compounds 5a, 5f, 5g, 5n, 5r, 5t, 5w, 5x and 5y demonstrated promising antibacterial activity while other derivatives showed comparable activity to standard drugs used as reference.

  20. Micellar solubilization of selected non-steroidal therapeutic agents by new surface-active agents of the class of the products of oxyethylation of ursodeoxycholic acid.

    Science.gov (United States)

    Zgoda, Marian Mikołaj; Lukosek, Marek; Nachajski, Michał Jakub

    2006-01-01

    A new class of non-ionic surface-active agents were synthesized by means of oxyethylation of ursodeoxycholic acid (UDOCh acid) with the application of modified generation of catalysts in the form of a model prodrug. Basic viscosity values ([eta], Meta, Ro, Robs., Omga) as well as the analytic level of hyrohilic-lipophilic balance HLB in the notation of Griffin, Davies and 'HNMR method were determined. In the state of equilibrium the solubilizing properties of aqueous solutions of the products of oxyetyenation of UDOCh acid x nTE were estimated with respect to non-steroidal therapeutic agents such as diclofenac, ibuprofen, ketoprofen, and naproxen. The surface activity of solubilizers of UDOCh acid > or = nTE = 30 type and the thermodynamic stability deltaGm of an adduct emerging in the state of equilibrium were determined.

  1. Interaction of surface-modified silica nanoparticles with clay minerals

    Directory of Open Access Journals (Sweden)

    Cigdem Omurlu

    2016-05-01

    Full Text Available Abstract In this study, the adsorption of 5-nm silica nanoparticles onto montmorillonite and illite is investigated. The effect of surface functionalization was evaluated for four different surfaces: unmodified, surface-modified with anionic (sulfonate, cationic (quaternary ammonium (quat, and nonionic (polyethylene glycol (PEG surfactant. We employed ultraviolet–visible spectroscopy to determine the concentration of adsorbed nanoparticles in conditions that are likely to be found in subsurface reservoir environments. PEG-coated and quat/PEG-coated silica nanoparticles were found to significantly adsorb onto the clay surfaces, and the effects of electrolyte type (NaCl, KCl and concentration, nanoparticle concentration, pH, temperature, and clay type on PEG-coated nanoparticle adsorption were studied. The type and concentration of electrolytes were found to influence the degree of adsorption, suggesting a relationship between the interlayer spacing of the clay and the adsorption ability of the nanoparticles. Under the experimental conditions reported in this paper, the isotherms for nanoparticle adsorption onto montmorillonite at 25 °C indicate that adsorption occurs less readily as the nanoparticle concentration increases.

  2. Modified Contact Line Dynamics about a Surface-Piercing Hydrofoil

    Science.gov (United States)

    Grivel, Morgane; Jeon, David; Gharib, Morteza

    2016-11-01

    The contact line around a surface-piercing hydrofoil is modified by introducing alternating hydrophobic and hydrophilic bands along one side of the body. These bands are either aligned perpendicular or parallel to the flow direction. The other side of the hydrofoil is un-patterned and retains its original, uniformly hydrophilic properties. The hydrofoil is mounted onto air bearings, such that it can freely move side-to-side in the water tunnel. A force sensor is attached to the setup via a universal joint in order to measure the forces acting on the body for several Reynolds numbers (ranging from 104 to 105) and angles of attack (ranging from -10o to 10o) . Cameras are also used to record the resulting flow structures and free surface elevation. The generation of wave trains and an altered free-surface elevation (also associated with the generation of surface waves) are observed over a wide range flow conditions. Force measurements elucidate how introducing these flow features impacts the forces acting on the hydrofoil, specifically with regards to the generation of lateral forces due to the asymmetric wetting conditions on either side of the hydrofoil. Work is funded by ONR Grant N00014-11-1-0031 and NSF GRFP Grant DGE-1144469.

  3. SURFACE-MODIFIED COALS FOR ENHANCED CATALYST DISPERSION AND LIQUEFACTION

    Energy Technology Data Exchange (ETDEWEB)

    Dr. Yaw D. Yeboah

    1999-09-01

    This is the final report of the Department of Energy Sponsored project DE-FGF22-95PC95229 entitled, surface modified coals for enhanced catalyst dispersion and liquefaction. The aims of the study were to enhance catalyst loading and dispersion in coal for improved liquefaction by preadsorption of surfactants and catalysts on the coal and to train and educate minority scientists in catalysts and separation science. Illinois No. 6 Coal (DEC-24) was selected for the study. The surfactants investigated included dodecyl dimethyl ethyl ammonium bromide (DDAB), a cationic surfactant, sodium dodecyl sulfate, an anionic surfactant, and Triton x-100, a neutral surfactant. Ammonium molybdate tetrahydrate was used as the molybdenum catalyst precursor. Zeta potential, BET, FTIR, AFM, UV-Vis and luminescence intensity measurements were undertaken to assess the surface properties and the liquefaction activities of the coal. The parent coal had a net negative surface charge over the pH range 2-12. However, in the presence of DDAB the negativity of the surface charge decreased. At higher concentrations of DDAB, a positive surface charge resulted. In contrast to the effect of DDAB, the zeta potential of the coal became more negative than the parent coal in the presence of SDS. Adsorption of Triton reduced the net negative charge density of the coal samples. The measured surface area of the coal surface was about 30 m{sup 2}/g compared to 77m{sup 2}/g after being washed with deionized water. Addition of the surfactants decreased the surface area of the samples. Adsorption of the molybdenum catalyst increased the surface area of the coal sample. The adsorption of molybdenum on the coal was significantly promoted by preadsorption of DDAB and SDS. Molybdenum adsorption showed that, over a wide range of concentrations and pH values, the DDAB treated coal adsorbed a higher amount of molybdenum than the samples treated with SDS. The infrared spectroscopy (FTIR) and the atomic force

  4. Surface modification of PCC with guar gum using organic titanium ionic crosslinking agent and its application as papermaking filler.

    Science.gov (United States)

    Xie, Wei; Song, Zhanqian; Liu, Zhenhua; Qian, Xueren

    2016-10-05

    Utilized the principles of guar gum (GG) gelation and crosslinking, a novel modified precipitated calcium carbonate (MPCC) papermaking filler was prepared by using organic titanium (OT) ionic crosslinking agent. The MPCC was characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). FTIR results confirmed that GG had been coated on the surface of PCC particles, XPS analysis indicated the presence of titanium atoms on MPCC particles, and SEM and XRD results showed that the modification treatment did change the surface morphology and crystal structure of PCC particles. The handsheet testing results showed that the strength properties of handsheets were obviously improved when using MPCC as papermaking filler, and the optimum preparation conditions of MPCC were obtained. This research suggests that the GG modified PCC by using OT as crosslinking agent can be used to manufacture high filler content paper products. Copyright © 2016 Elsevier Ltd. All rights reserved.

  5. A Multi-Agent System for Tracking the Intent of Surface Contacts in Ports and Waterways

    National Research Council Canada - National Science Library

    Tan, Kok S

    2005-01-01

    ...) and employ them to identify asymmetric maritime threats in port and waterways. Each surface track is monitored by a compound multi-agent system that comprise of the several intent models, each containing a nested multi-agent system...

  6. Ultraviolet Raman Spectral Signatures in Support of Lisa (Laser Interrogation of Surface Agents)

    National Research Council Canada - National Science Library

    Sedlacek, III, Arthur J; Finfrock, Charles C; Christesen, Steve; Chyba, Tom; Higdon, Scott

    2003-01-01

    ... (Laser Interrogation of Surface Agents). This engineering, testing and evaluation effort uses a novel mini-Raman lidar technique for on-the-move, short-range, non-contact detection and identification of chemical agents on the battlefield...

  7. Surface-modified low-temperature solid oxide fuel cell

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Young Beom; Holme, Timothy P. [Department of Mechanical Engineering, Stanford University, Stanford, CA 94305 (United States); Guer, Turgut M. [Department of Materials Science and Engineering, Stanford University, Stanford, CA 94305 (United States); Prinz, Fritz B. [Department of Mechanical Engineering, Stanford University, Stanford, CA 94305 (United States); Department of Materials Science and Engineering, Stanford University, Stanford, CA 94305 (United States)

    2011-12-20

    This paper reports both experimental and theoretical results of the role of surface modification on the oxygen reduction reaction in low-temperature solid oxide fuel cells (LT-SOFC). Epitaxial ultrathin films of yttria-doped ceria (YDC) cathode interlayers (<10-130 nm) are grown by pulsed laser deposition (PLD) on single-crystalline YSZ(100). Fuel cell current-voltage measurements and electrochemical impedance spectroscopy are performed in the temperature range of 350 C {approx} 450 C. Quantum mechanical simulations of oxygen incorporation energetics support the experimental results and indicate a low activation energy of only 0.07 eV for YDC, while the incorporation reaction on YSZ is activated by a significantly higher energy barrier of 0.38 eV. Due to enhanced oxygen incorporation at the modified Pt/YDC interface, the cathodic interface resistance is reduced by two-fold, while fuel cell performance shows more than a two-fold enhancement with the addition of an ultrathin YDC interlayer at the cathode side of an SOFC element. The results of this study open up opportunities for improving cell performance, particularly of LT-SOFCs by adopting surface modification of YSZ surface with catalytically superior, ultrathin cathodic interlayers. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  8. Onion-like surface design of upconverting nanophosphors modified with polyethylenimine: shielding toxicity versus keeping brightness?

    Science.gov (United States)

    Guller, Anna; Nadort, Annemarie; Generalova, Alla; Kornienko, Inna; Petersen, Elena; Qian, Yi; Shekhter, Anatoly; Goldys, Ewa; Zvyagin, Andrei

    2016-12-01

    Background: Upconverting nanoparticles (UCNPs) represent a unique class of nanomaterials, able to convert infrared excitation light into long lifetime visible and infrared photoluminescence, within the "optical transparency window" of biological tissues. This makes UCNPs an attractive contrast agent for background-free bioimaging. However, assynthesized UCNPs are hydrophobic and need additional surface coating for stability in water-based solutions and further functionalization. Polyethylenimine (PEI), a polycationic amphiphilic polymer, is a well-known transfection agent for gene delivery and a popular material for UCNPs surface hydrophilization. Combining the functional properties of UCNPs and PEI is extremely useful for precise visualization of genetic manipulations and intracellular drug delivery. At the same time, PEI is toxic to cells, while the photoluminescent properties of UCNPs are very sensitive to surface chemistry and environment. Then, creation of hydrophilic, biocompatible and simultaneously bright UCNPs, modified by PEI (UCNP-PEI), is a challenging task. Objectives: To analyze the effects of multilayer shielding coatings on cytotoxicity, cellular uptake and photoluminescent properties of UCNP-PEI. Methods and results: UCNP-PEI were modified with additional two or three layers of various polymers and characterized by size, surface charge and photophysical properties. HaCaT keratinocytes were exposed to the particles for 24 or 120 h to study the cytotoxicity and cellular uptake. The results show that onion-like coatings of UCNP-PEI simultaneously decrease cytotoxicity and relative luminescence of the particles, depending on structure and method of formation of multilayer coating. Conclusions: Rational design of UCNP-PEI using extra coatings layers can help to keep acceptable levels of biocompatibility and photoluminescence intensity.

  9. Research on the Preparation and Performance of Binary Modified Maltodextrin Water-Reducing Agent

    Directory of Open Access Journals (Sweden)

    Jingzhi Wu

    2016-01-01

    Full Text Available Using maltodextrin (MD of different dextrose equivalent (DE values, 1,3-propanesultone, and maleic anhydride as raw materials, a novel binary modified maltodextrin (BMMD was synthesized and further applied as a water-reducing agent. Its structure was characterized by Fourier transform infrared (FT-IR and UV. The rheological behavior of the sample solution and strengths for concrete were also determined and the adsorption was tested by TOC. The influence of the process parameters to degree of substitution (DS and the dosage on the fluidity of cement paste were investigated. The results show that the optimal conditions of sulfonation were the MD of DE 15, m (sulfonated agent/m (MD of 1.4, the catalyst amount of 1% by mass MD, and the reaction time of 12 h; the optimal conditions of esterification were m (esterified agent/m (SMD of 0.6, the reaction temperature of 90°C, and the reaction time of 4 h. The optimal dosages of sulfonated maltodextrin (SMD and BMMD were 0.475% and 0.45%, respectively. In this dosage, the main dispersion capacity of BMMD attributes to two kinds of anchoring groups (SO3-  &  COO- and the appropriate molecular weight of MD.

  10. Implications of Rheumatic Disease and Biological Response-Modifying Agents in Plastic Surgery.

    Science.gov (United States)

    Tsai, David M; Borah, Gregory L

    2015-12-01

    The preoperative evaluation for any reconstructive or aesthetic procedure requires a detailed history of existing medical conditions and current home medications. The prevalence of rheumatic diseases such as rheumatoid arthritis, gout, and psoriasis is high, but the impact of these chronic illnesses on surgical outcome and the side effects of the powerful medications used for treatment are often underappreciated. In this review, the authors highlight key perioperative considerations specific to rheumatologic diseases and their associated pharmacologic therapies. In particular, the authors discuss the perioperative management of biological response-modifying agents, which have largely become the new standard of therapy for many rheumatic diseases. The literature reveals three key perioperative concerns with biological therapy for rheumatic disease: infection, wound healing delays, and disease flare. However, data on specific perioperative complications are lacking, and it remains controversial whether withholding biological therapy before surgery is of benefit. The risk of these adverse events is influenced by several factors: age, sex, class of biological agent, duration of exposure, dosage, onset and severity of disease, and type of surgical procedure. Overall, it remains best to develop an individualized plan. In younger patients with recent onset of biological therapy, it is reasonable to withhold therapy based on 3 to 5 half-lives of the specific agent. In older patients with a substantial history of rheumatic disease, the decision to discontinue therapy must be weighed and decided carefully in conjunction with the rheumatologist.

  11. Morphology and optical properties of aluminum oxide formed into oxalic electrolyte with addition surface active agents

    International Nuclear Information System (INIS)

    Kazarkin, B; Stsiapanau, A; Smirnov, A; Zhilinski, V; Chernik, A; Bezborodov, V; Kozak, G; Danilovich, S

    2016-01-01

    The article discusses the results of investigations of porous films of alumina, formed into oxalic electrolyte with addition surface active agents, in particular, ordering structure, roughness of a surface, the optical transparency of the electrolyte concentration and surface active agents. Also discusses the features of the formation of porous films of temperature and IR radiation. (paper)

  12. Epoxy coatings electrodeposited on aluminium and modified aluminium surfaces

    Directory of Open Access Journals (Sweden)

    Lazarević Zorica Ž.

    2002-01-01

    Full Text Available The corrosion behaviour and thermal stability of epoxy coatings electrodeposited on modified aluminum surfaces (anodized, phosphatized and chromatized-phosphatized aluminium were monitored during exposure to 3% NaCl solution, using electrochemical impedance spectroscopy (EIS and thermogravimetric analysis (TGA. Better protective properties of the epoxy coatings on anodized and chromatized-phosphatized aluminum with respect to the same epoxy coatings on aluminum and phosphatized aluminum were obtained: higher values of Rp and Rct and smaller values of Cc and Cd, from EIS, and a smaller amount of absorbed water inside the coating, from TGA. On the other hand, a somewhat lower thermal stability of these coatings was obtained (smaller values of the ipdt temperature. This behavior can be explained by the less porous structure of epoxy coatings on anodized and chromatized-phosphatized aluminum, caused by a lower rate of H2 evolution and better wet ability.

  13. Occurrence of Surface Active Agents in the Environment

    Directory of Open Access Journals (Sweden)

    Ewa Olkowska

    2014-01-01

    Full Text Available Due to the specific structure of surfactants molecules they are applied in different areas of human activity (industry, household. After using and discharging from wastewater treatment plants as effluent stream, surface active agents (SAAs are emitted to various elements of the environment (atmosphere, waters, and solid phases, where they can undergo numerous physic-chemical processes (e.g., sorption, degradation and freely migrate. Additionally, SAAs present in the environment can be accumulated in living organisms (bioaccumulation, what can have a negative effect on biotic elements of ecosystems (e.g., toxicity, disturbance of endocrine equilibrium. They also cause increaseing solubility of organic pollutants in aqueous phase, their migration, and accumulation in different environmental compartments. Moreover, surfactants found in aerosols can affect formation and development of clouds, which is associated with cooling effect in the atmosphere and climate changes. The environmental fate of SAAs is still unknown and recognition of this problem will contribute to protection of living organisms as well as preservation of quality and balance of various ecosystems. This work contains basic information about surfactants and overview of pollution of different ecosystems caused by them (their classification and properties, areas of use, their presence, and behavior in the environment.

  14. Modified titanium surface with gelatin nano gold composite increases osteoblast cell biocompatibility

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Young-Hee; Bhattarai, Govinda [Department of Oral Biochemistry, School of Dentistry and Institute of Oral Bioscience, BK21 program, Chonbuk National University, Jeonju (Korea, Republic of); Aryal, Santosh [Department of Bionanosystem Engineering, Chonbuk National University, Jeonju (Korea, Republic of); Lee, Nan-Hee [Department of Oral Biochemistry, School of Dentistry and Institute of Oral Bioscience, BK21 program, Chonbuk National University, Jeonju (Korea, Republic of); Lee, Min-Ho [Department of Dental Biomaterials, School of Dentistry and Institute of Oral Bioscience, BK21 program, Chonbuk National University, Jeonju (Korea, Republic of); Kim, Tae-Gun [Department of Conservative Dentistry, School of Dentistry, Chonbuk National University, Jeonju (Korea, Republic of); Jhee, Eun-Chung [Department of Oral Biochemistry, School of Dentistry and Institute of Oral Bioscience, BK21 program, Chonbuk National University, Jeonju (Korea, Republic of); Kim, Hak-Yong [Department of Bionanosystem Engineering, Chonbuk National University, Jeonju (Korea, Republic of); Yi, Ho-Keun, E-mail: yihokn@chonbuk.ac.kr [Department of Oral Biochemistry, School of Dentistry and Institute of Oral Bioscience, BK21 program, Chonbuk National University, Jeonju (Korea, Republic of)

    2010-08-01

    This study examined the gelatin nano gold (GnG) composite for surface modification of titanium in addition to insure biocompatibility on dental implants or biomaterials. The GnG composite was constructed by gelatin and hydrogen tetrachloroaurate in presence of reducing agent, sodium borohydrate (NabH{sub 4}). The GnG composite was confirmed by UV-VIS spectroscopy and transmission electron microscopy (TEM). A dipping method was used to modify the titanium surface by GnG composite. Surface was characterized by scanning electron microscopy (SEM) and energy dispersive X-ray (EDX). The MC-3T3 E1 cell viability was assessed by trypan blue and the expression of proteins to biocompatibility were analyzed by Western blotting. The GnG composite showed well dispersed character, the strong absorption at 530 nm, roughness, regular crystal and clear C, Na, Cl, P, and Au signals onto titanium. Further, this composite allowed MC-3T3 E1 growth and viability compared to gelatin and pure titanium. It induced ERK activation and the expression of cell adherent molecules, FAK and SPARC, and growth factor, VEGF. However, GnG decreased the level of SAPK/JNK. This shows that GnG composite coated titanium surfaces have a good biocompatibility for osteoblast growth and attachment than in intact by simple and versatile dipping method. Furthermore, it offers good communication between cell and implant surfaces by regulating cell signaling and adherent molecules, which are useful to enhance the biocompatibility of titanium surfaces.

  15. Modified titanium surface with gelatin nano gold composite increases osteoblast cell biocompatibility

    Science.gov (United States)

    Lee, Young-Hee; Bhattarai, Govinda; Aryal, Santosh; Lee, Nan-Hee; Lee, Min-Ho; Kim, Tae-Gun; Jhee, Eun-Chung; Kim, Hak-Yong; Yi, Ho-Keun

    2010-08-01

    This study examined the gelatin nano gold (GnG) composite for surface modification of titanium in addition to insure biocompatibility on dental implants or biomaterials. The GnG composite was constructed by gelatin and hydrogen tetrachloroaurate in presence of reducing agent, sodium borohydrate (NabH 4). The GnG composite was confirmed by UV-VIS spectroscopy and transmission electron microscopy (TEM). A dipping method was used to modify the titanium surface by GnG composite. Surface was characterized by scanning electron microscopy (SEM) and energy dispersive X-ray (EDX). The MC-3T3 E1 cell viability was assessed by trypan blue and the expression of proteins to biocompatibility were analyzed by Western blotting. The GnG composite showed well dispersed character, the strong absorption at 530 nm, roughness, regular crystal and clear C, Na, Cl, P, and Au signals onto titanium. Further, this composite allowed MC-3T3 E1 growth and viability compared to gelatin and pure titanium. It induced ERK activation and the expression of cell adherent molecules, FAK and SPARC, and growth factor, VEGF. However, GnG decreased the level of SAPK/JNK. This shows that GnG composite coated titanium surfaces have a good biocompatibility for osteoblast growth and attachment than in intact by simple and versatile dipping method. Furthermore, it offers good communication between cell and implant surfaces by regulating cell signaling and adherent molecules, which are useful to enhance the biocompatibility of titanium surfaces.

  16. Influence of spacer length on heparin coupling efficiency and fibrinogen adsorption of modified titanium surfaces

    Directory of Open Access Journals (Sweden)

    Gbureck Uwe

    2007-07-01

    Full Text Available Abstract Background Chemical bonding of the drug onto surfaces by means of spacer molecules is accompanied with a reduction of the biological activity of the drug due to a constricted mobility since normally only short spacer molecule like aminopropyltrimethoxysilane (APMS are used for drug coupling. This work aimed to study covalent attachment of heparin to titanium(oxide surfaces by varying the length of the silane coupling agent, which should affect the biological potency of the drug due to a higher mobility with longer spacer chains. Methods Covalent attachment of heparin to titanium metal and TiO2 powder was carried out using the coupling agents 3-(Trimethoxysilyl-propylamine (APMS, N- [3-(Trimethoxysilylpropyl]ethylenediamine (Diamino-APMS and N1- [3-(Trimethoxy-silyl-propyl]diethylenetriamine (Triamino-APMS. The amount of bound coupling agent and heparin was quantified photometrically by the ninhydrin reaction and the tolidine-blue test. The biological potency of heparin was determined photometrically by the chromogenic substrate Chromozym TH and fibrinogen adsorption to the modified surfaces was researched using the QCM-D (Quartz Crystal Microbalance with Dissipation Monitoring technique. Results Zeta-potential measurements confirmed the successful coupling reaction; the potential of the unmodified anatase surface (approx. -26 mV shifted into the positive range (> + 40 mV after silanisation. Binding of heparin results in a strongly negatively charged surface with zeta-potentials of approx. -39 mV. The retaining biological activity of heparin was highest for the spacer molecule Triamino-APMS. QCM-D measurements showed a lower viscosity for adsorbed fibrinogen films on heparinised surfaces by means of Triamino-APMS. Conclusion The remaining activity of heparin was found to be highest for the covalent attachment with Triamino-APMS as coupling agent due to the long chain of this spacer molecule and therefore the highest mobility of the drug

  17. Nature of the Elimination of the Penicillinase Plasmid from Staphylococcus aureus by Surface-Active Agents

    Science.gov (United States)

    Sonstein, Stephen A.; Baldwin, J. N.

    1972-01-01

    Growth of Stapylococcus aureus in various ionic surface-active agents resulted in loss of the ability to produce penicillinase, whereas growth in nonionic surface-active agents had no effect on penicillinase production. The curing effect of various alkyl sulfates was found to be dependent upon the chain length. Curing by surface-active agents could be inhibited by magnesium. Reciprocal transduction experiments showed that curing by a surface-active agent was a property of the plasmid, not of the bacterial strain in which the plasmic resides. PMID:4204903

  18. Flavonoid-modified surfaces: multifunctional bioactive biomaterials with osteopromotive, anti-inflammatory, and anti-fibrotic potential.

    Science.gov (United States)

    Córdoba, Alba; Satué, María; Gómez-Florit, Manuel; Hierro-Oliva, Margarita; Petzold, Christiane; Lyngstadaas, Staale P; González-Martín, María Luisa; Monjo, Marta; Ramis, Joana M

    2015-03-11

    Flavonoids are small polyphenolic molecules of natural origin with antioxidant, anti-inflammatory, and antibacterial properties. Here, a bioactive surface based on the covalent immobilization of flavonoids taxifolin and quercitrin on titanium substrates is presented, using (3-aminopropyl)triethoxysilane (APTES) as coupling agent. FTIR and XPS measurements confirm the grafting of the flavonoids to the surfaces. Using 2-aminoethyl diphenylborinate (DPBA, a flavonoid-specific dye), the modified surfaces are imaged by fluorescence microscopy. The bioactivity of the flavonoid-modified surfaces is evaluated in vitro with human umbilical cord derived mesenchymal stem cells (hUC-MSCs) and human gingival fibroblasts (HGFs) and compared to that of simple flavonoid coatings prepared by drop casting. Flavonoid-modified surfaces show anti-inflammatory and anti-fibrotic potential on HGF. In addition, Ti surfaces covalently functionalized with flavonoids promote the differentiation of hUC-MSCs to osteoblasts--enhancing the expression of osteogenic markers, increasing alkaline phosphatase activity and calcium deposition; while drop-casted surfaces do not. These findings could have a high impact in the development of advanced implantable medical devices like bone implants. Given the broad range of bioactivities of flavonoid compounds, these surfaces are ready to be explored for other biomedical applications, e.g., as stent surface or tumor-targeted functionalized nanoparticles for cardiovascular or cancer therapies. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  19. Improved Composites Using Crosslinked, Surface-Modified Carbon Nanotube Materials

    Science.gov (United States)

    Baker, James Stewart

    2014-01-01

    Individual carbon nanotubes (CNTs) exhibit exceptional tensile strength and stiffness; however, these properties have not translated well to the macroscopic scale. Premature failure of bulk CNT materials under tensile loading occurs due to the relatively weak frictional forces between adjacent CNTs, leading to poor load transfer through the material. When used in polymer matrix composites (PMCs), the weak nanotube-matrix interaction leads to the CNTs providing less than optimal reinforcement.Our group is examining the use of covalent crosslinking and surface modification as a means to improve the tensile properties of PMCs containing carbon nanotubes. Sheet material comprised of unaligned multi-walled carbon nanotubes (MWCNT) was used as a drop-in replacement for carbon fiber in the composites. A variety of post-processing methods have been examined for covalently crosslinking the CNTs to overcome the weak inter-nanotube shear interactions, resulting in improved tensile strength and modulus for the bulk sheet material. Residual functional groups from the crosslinking chemistry may have the added benefit of improving the nanotube-matrix interaction. Composites prepared using these crosslinked, surface-modified nanotube sheet materials exhibit superior tensile properties to composites using the as received CNT sheet material.

  20. The Ice Nucleation Activity of Surface Modified Soot

    Science.gov (United States)

    Häusler, Thomas; Witek, Lorenz; Felgitsch, Laura; Hitzenberger, Regina; Grothe, Hinrich

    2017-04-01

    The ice nucleation efficiency of many important atmospheric particles remains poorly understood. Since soot is ubiquitous in the Earth's troposphere, they might have the potential to significantly impact the Earth's climate (Finlayson-Pitts and Pitts, 2000; Seinfeld and Pandis, 1998). Here we present the ice nucleation activity (INA) in immersion freezing mode of different types of soot. Therefor a CAST (combustion aerosol standard) generator was used to produce different kinds of soot samples. The CAST generator combusts a propane-air-mixture and deposits thereby produced soot on a polyvinyl fluoride filter. By varying the propane to air ratio, the amount of organic portion of the soot can be varied from black carbon (BC) with no organic content to brown carbon (BrC) with high organic content. To investigate the impact of functional sites of ice nuclei (IN), the soot samples were exposed to NO2 gas for a certain amount of time (30 to 360 minutes) to chemically modify the surface. Immersion freezing experiments were carried out in a unique reaction gadget. In this device a water-in-oil suspension (with the soot suspended in the aqueous phase) was cooled till the freezing point and was observed through a microscope (Pummer et al., 2012; Zolles et al., 2015) It was found that neither modified nor unmodified BC shows INA. On the contrary, unmodified BrC shows an INA at -32˚ C, which can be increased up to -20˚ C. The INA of BrC depends on the duration of NO2- exposure. To clarify the characteristics of the surface modifications, surface sensitive analysis like infrared spectroscopy and X-ray photoelectron spectroscopy were carried out. Finlayson-Pitts, B. J. and Pitts, J. N. J.: Chemistry of the Upper and Lower Atmosphere, Elsevier, New York, 2000. Pummer, B. G., Bauer, H., Bernardi, J., Bleicher, S., and Grothe, H.: Suspendable macromolecules are responsible for ice nucleation activity of birch and conifer pollen, Atmos Chem Phys, 12, 2541-2550, 2012. Seinfeld, J

  1. STUDY OF SURFACE MODIFIED POLYMERS IN THE MODIFICATION OF NANOMATERIALS

    Directory of Open Access Journals (Sweden)

    G. V. Popov

    2014-01-01

    Full Text Available The comparative study of change of surface tension of solutions of some commercial rubbers before and after thermal ageing technique du-Nui, analyzed the features of change of surface tension of solutions of various rubbers in the presence of a mixture of fullerenes. Calculations of the Gibbs energy and the analysis of the obtained data to predict the behavior of polymer systems when changes are made to mix of fullerenes in a wide concentration range. When comparing the results of changes in Gibbs energy and the surface tension in fluids rubbers shown that mentioned above in solutions of elastomers aged, than the control. This fact confirms the initial chapeau of physic-chemical interactions of molecules fullerenes by segments of the Kuna and end groups of the polymer chains, as it is known that when thermal-oxidative degradation of rubbers, respectively the number of segments of the Kuna and branched loose ends of macromolecules that are free to react with fullerenes in solution, free from spatial constraints. A comparative analysis of the interaction of rubbers with different chemical composition with double branches has shown that it is easier to just react and has minimum energy polibutadien interaction that has to do with lack of branching and no radicals in its structure and in the backbone chain. The maximum energy of interaction with Fullerenes have SBS rubber because it has large styrene blocks in the main polymer chain that causes the spatial constraints to direct contact with fullerene molecules, you can assume that the interaction is only low-molecular fraction of Fullerenes mixture, possessing the necessary dimensions. As a result of the study shows that the application of the method of separation ring (Du-Nui allows you to predict the properties of rubber with modified nanomaterial’s with minimal labor costs.

  2. Modified Titanium Surface-Mediated Effects on Human Bone Marrow Stromal Cell Response

    Science.gov (United States)

    Chaudhari, Amol; Duyck, Joke; Braem, Annabel; Vleugels, Jozef; Petite, Hervé; Logeart-Avramoglou, Delphine; Naert, Ignace; Martens, Johan A.; Vandamme, Katleen

    2013-01-01

    Surface modification of titanium implants is used to enhance osseointegration. The study objective was to evaluate five modified titanium surfaces in terms of cytocompatibility and pro-osteogenic/pro-angiogenic properties for human mesenchymal stromal cells: amorphous microporous silica (AMS), bone morphogenetic protein-2 immobilized on AMS (AMS + BMP), bio-active glass (BAG) and two titanium coatings with different porosity (T1; T2). Four surfaces served as controls: uncoated Ti (Ti), Ti functionalized with BMP-2 (Ti + BMP), Ti surface with a thickened titanium oxide layer (TiO2) and a tissue culture polystyrene surface (TCPS). The proliferation of eGFP-fLuc (enhanced green fluorescence protein-firefly luciferase) transfected cells was tracked non-invasively by fluorescence microscopy and bio-luminescence imaging. The implant surface-mediated effects on cell differentiation potential was tracked by determination of osteogenic and angiogenic parameters [alkaline phosphatase (ALP); osteocalcin (OC); osteoprotegerin (OPG); vascular endothelial growth factor-A (VEGF-A)]. Unrestrained cell proliferation was observed on (un)functionalized Ti and AMS surfaces, whereas BAG and porous titanium coatings T1 and T2 did not support cell proliferation. An important pro-osteogenic and pro-angiogenic potential of the AMS + BMP surface was observed. In contrast, coating the Ti surface with BMP did not affect the osteogenic differentiation of the progenitor cells. A significantly slower BMP-2 release from AMS compared to Ti supports these findings. In the unfunctionalized state, Ti was found to be superior to AMS in terms of OPG and VEGF-A production. AMS is suggested to be a promising implant coating material for bioactive agents delivery. PMID:28788407

  3. Modified Titanium Surface-Mediated Effects on Human Bone Marrow Stromal Cell Response

    Directory of Open Access Journals (Sweden)

    Amol Chaudhari

    2013-11-01

    Full Text Available Surface modification of titanium implants is used to enhance osseointegration. The study objective was to evaluate five modified titanium surfaces in terms of cytocompatibility and pro-osteogenic/pro-angiogenic properties for human mesenchymal stromal cells: amorphous microporous silica (AMS, bone morphogenetic protein-2 immobilized on AMS (AMS + BMP, bio-active glass (BAG and two titanium coatings with different porosity (T1; T2. Four surfaces served as controls: uncoated Ti (Ti, Ti functionalized with BMP-2 (Ti + BMP, Ti surface with a thickened titanium oxide layer (TiO2 and a tissue culture polystyrene surface (TCPS. The proliferation of eGFP-fLuc (enhanced green fluorescence protein-firefly luciferase transfected cells was tracked non-invasively by fluorescence microscopy and bio-luminescence imaging. The implant surface-mediated effects on cell differentiation potential was tracked by determination of osteogenic and angiogenic parameters [alkaline phosphatase (ALP; osteocalcin (OC; osteoprotegerin (OPG; vascular endothelial growth factor-A (VEGF-A]. Unrestrained cell proliferation was observed on (unfunctionalized Ti and AMS surfaces, whereas BAG and porous titanium coatings T1 and T2 did not support cell proliferation. An important pro-osteogenic and pro-angiogenic potential of the AMS + BMP surface was observed. In contrast, coating the Ti surface with BMP did not affect the osteogenic differentiation of the progenitor cells. A significantly slower BMP-2 release from AMS compared to Ti supports these findings. In the unfunctionalized state, Ti was found to be superior to AMS in terms of OPG and VEGF-A production. AMS is suggested to be a promising implant coating material for bioactive agents delivery.

  4. Surface characterization and stability of an epoxy resin surface modified with polyamines grafted on polydopamine

    Science.gov (United States)

    Schaubroeck, David; Vercammen, Yannick; Van Vaeck, Luc; Vanderleyden, Els; Dubruel, Peter; Vanfleteren, Jan

    2014-06-01

    This paper reports on polydopamine and polyamine surface modifications of an etched epoxy cresol novolac (ECN) resin using the 'grafting to' method. Three different polyamines are used for the grafting reactions: branched polyethyleneimine (B-PEI), linear polyethyleneimine (L-PEI) and diethylenetriamine (DETA). These modifications are compared to control materials prepared via direct deposition of polyamines. The stability of the modifications toward a concentrated hydrochloric acid (HCl) environment is evaluated. The modified surfaces are characterized with scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and time-of-flight static secondary ion mass spectroscopy (TOF-S-SIMS).

  5. Surface modification of silicon carbide with silane coupling agent and hexadecyl iodiele

    Energy Technology Data Exchange (ETDEWEB)

    Shang, Xujing, E-mail: shangxujing@tju.edu.cn; Zhu, Yumei, E-mail: zymtju@163.com; Li, Zhihong, E-mail: lzhtju@163.com

    2017-02-01

    Highlights: • A novel universal method was performed to enhance hydrophobicity of SiC powder. • The modification effects of KH550 and KH590 were compared and the optimum reaction parameters were established. • Hexadecyl iodiele was successfully grafted on the surface of SiC-KH590 powder. • Surface changes on SiC powder before and after modification were analyzed via FTIR, XPS, SEM. • The related reaction mechanisms were discussed. - Abstract: In this paper, two kinds of silane coupling agents, namely 3-aminopropyl triethoxysilane (KH550) and 3-mercaptopropyl trimethoxysilane (KH590), were adopted as preliminary modifiers to improve the hydrophobic surface properties of silicon carbide (SiC) powder for the first step. The factors that influence the modification effects were investigated by measuring the contact angle. The results showed that KH590 has a better effect than KH550 for the hydrophobic modification of SiC, and the contact angle improved most after SiC powder was reacted with 0.3 g KH590 at 75 °C in aqueous/alcohol solution for 4 h. On account of further enhancement of hydrophobicity, the study was focused on utilizing nucleophilic substitution between KH590 and hexadecyl iodiele to extend the length of alkyl chain. Compared with using KH590 alone, SiC powder modified by KH590 and hexadecyl iodiele showed better water resistance with an increase of contact angle from 106.8° to 127.5°. The Fourier transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectra (XPS) as well as X-ray diffraction (XRD) analysis results showed that KH550/KH590 and hexadecyl iodiele can be covalently bonded to the surface of SiC powder without altering its crystal configuration. This methodology may provide a new way of the modification of inorganic materials in further.

  6. Evaluation of the effect of home bleaching agents on surface microhardness of different glass-ionomer cements containing hydroxyapatite.

    Science.gov (United States)

    Sharafeddin, Farahnaz; Kowkabi, Mahsa; Shoale, Soodabe

    2017-09-01

    Home bleaching agents may exert some negative effects on surface hardness of restorative materials such as glass-ionomer cements (GICs). Since some studies have shown that some components such as hydroxyapatite (HA), as a bioactive glass, can improve the mechanical properties of dental materials, the effect of bleaching agents on surface hardness of GICs containing hydroxyapatite is questionable. This study was designed to evaluate the effect of home bleaching agents on the surface hardness of two different commercially available GICs containing hydroxyapatite. 80 disk-shaped specimens were made from two different GICs, including resin modified glass-ionomer and Zirconomer. Each material was divided into four groups (n=10): 1. control, 2. 20 %wt. hydroxyapatite-containing, 3. bleached and 4. bleached 20 %wt. hydroxyapatite-containing. Group 1 and 2 specimens were stored in distilled water for 2 weeks while group 3 and 4 specimens were treated with 15% carbamide peroxide in that period. Surface hardness was tested with Vickers surface hardness tester. Data were analyzed with 3-way ANOVA and mean comparison done by post hoc Tukey tests ( p Glass-ionomer cement, surface hardness, Zirconia-reinforced glass ionomer, hydroxyapatite.

  7. A Modified Dynamic Surface Controller for Delayed Neuromuscular Electrical Stimulation.

    Science.gov (United States)

    Alibeji, Naji; Kirsch, Nicholas; Dicianno, Brad E; Sharma, Nitin

    2017-08-01

    A widely accepted model of muscle force generation during neuromuscular electrical stimulation (NMES) is a second-order nonlinear musculoskeletal dynamics cascaded to a delayed first-order muscle activation dynamics. However, most nonlinear NMES control methods have either neglected the muscle activation dynamics or used an ad hoc strategies to tackle the muscle activation dynamics, which may not guarantee control stability. We hypothesized that a nonlinear control design that includes muscle activation dynamics can improve the control performance. In this paper, a dynamic surface control (DSC) approach was used to design a PID-based NMES controller that compensates for EMD in the activation dynamics. Because the muscle activation is unmeasurable, a model based estimator was used to estimate the muscle activation in realtime. The Lyapunov stability analysis confirmed that the newly developed controller achieves semi-global uniformly ultimately bounded (SGUUB) tracking for the musculoskeletal system. Experiments were performed on two able-bodied subjects and one spinal cord injury subject using a modified leg extension machine. These experiments illustrate the performance of the new controller and compare it to a previous PID-DC controller that did not consider muscle activation dynamics in the control design. These experiments support our hypothesis that a control design that includes muscle activation improves the NMES control performance.

  8. Estimated Chemical Warfare Agent Surface Clearance Goals for Remediation Pre-Planning

    Energy Technology Data Exchange (ETDEWEB)

    Dolislager, Frederick [University of Tennessee, Knoxville (UTK); Bansleben, Dr. Donald [U.S. Department of Homeland Security; Watson, Annetta Paule [ORNL

    2010-01-01

    Health-based surface clearance goals, in units of mg/cm2, have been developed for the persistent chemical warfare agents sulfur mustard (HD) and nerve agent VX as well as their principal degradation products. Selection of model parameters and critical receptor (toddler child) allow calculation of surface residue estimates protective for the toddler child, the general population and adult employees of a facilty that has undergone chemical warfare agent attack.

  9. Acute effects of vascular modifying agents in solid tumors assessed by noninvasive laser Doppler flowmetry and near infrared spectroscopy

    DEFF Research Database (Denmark)

    Kragh, Michael; Quistorff, Bjørn; Horsman, Michael R

    2002-01-01

    The potential of noninvasive laser Doppler flowmetry (LDF) and near infrared spectroscopy (NIRS) to detect acute effects of different vascular-modifying agents on perfusion and blood volume in tumors was evaluated. C3H mouse mammary carcinomas (approximately 200 mm(3)) in the rear foot of CDF1 mice...... that the mechanism of action of CA4DP was vascular shut down with the blood pool trapped in the tumor. NTA caused no change in either tumor perfusion or tumor blood volume. We conclude that noninvasive LDF and NIRS can determine acute effects of vascular modifying agents on tumor perfusion and blood volume....

  10. Surface chemical and biological characterization of flax fabrics modified with silver nanoparticles for biomedical applications

    International Nuclear Information System (INIS)

    Paladini, F.; Picca, R.A.; Sportelli, M.C.; Cioffi, N.; Sannino, A.; Pollini, M.

    2015-01-01

    Silver nanophases are increasingly used as effective antibacterial agent for biomedical applications and wound healing. This work aims to investigate the surface chemical composition and biological properties of silver nanoparticle-modified flax substrates. Silver coatings were deposited on textiles through the in situ photo-reduction of a silver solution, by means of a large-scale apparatus. The silver-coated materials were characterized through X-ray Photoelectron Spectroscopy (XPS), to assess the surface elemental composition of the coatings, and the chemical speciation of both the substrate and the antibacterial nanophases. A detailed investigation of XPS high resolution regions outlined that silver is mainly present on nanophases' surface as Ag 2 O. Scanning electron microscopy and energy dispersive X-ray spectroscopy were also carried out, in order to visualize the distribution of silver particles on the fibers. The materials were also characterized from a biological point of view in terms of antibacterial capability and cytotoxicity. Agar diffusion tests and bacterial enumeration tests were performed on Gram positive and Gram negative bacteria, namely Staphylococcus aureus and Escherichia coli. In vitro cytotoxicity tests were performed through the extract method on murine fibroblasts in order to verify if the presence of the silver coating affected the cellular viability and proliferation. Durability of the coating was also assessed, thus confirming the successful scaling up of the process, which will be therefore available for large-scale production. - Highlights: • Silver nanophases are increasingly used as effective antibacterial agent for biomedical applications. • Silver coatings were deposited on textiles through the in situ photo-reduction of a silver solution. • Flax fabrics were characterized from a biological and surface chemical point of view. • Scaling up of the process was confirmed

  11. Surface chemical and biological characterization of flax fabrics modified with silver nanoparticles for biomedical applications

    Energy Technology Data Exchange (ETDEWEB)

    Paladini, F., E-mail: federica.paladini@unisalento.it [Department of Engineering for Innovation, University of Salento, Via per Monteroni, 73100 Lecce (Italy); Picca, R.A.; Sportelli, M.C.; Cioffi, N. [Department of Chemistry, University of Bari “Aldo Moro”, Via Orabona 4, 70126 Bari (Italy); Sannino, A.; Pollini, M. [Department of Engineering for Innovation, University of Salento, Via per Monteroni, 73100 Lecce (Italy)

    2015-07-01

    Silver nanophases are increasingly used as effective antibacterial agent for biomedical applications and wound healing. This work aims to investigate the surface chemical composition and biological properties of silver nanoparticle-modified flax substrates. Silver coatings were deposited on textiles through the in situ photo-reduction of a silver solution, by means of a large-scale apparatus. The silver-coated materials were characterized through X-ray Photoelectron Spectroscopy (XPS), to assess the surface elemental composition of the coatings, and the chemical speciation of both the substrate and the antibacterial nanophases. A detailed investigation of XPS high resolution regions outlined that silver is mainly present on nanophases' surface as Ag{sub 2}O. Scanning electron microscopy and energy dispersive X-ray spectroscopy were also carried out, in order to visualize the distribution of silver particles on the fibers. The materials were also characterized from a biological point of view in terms of antibacterial capability and cytotoxicity. Agar diffusion tests and bacterial enumeration tests were performed on Gram positive and Gram negative bacteria, namely Staphylococcus aureus and Escherichia coli. In vitro cytotoxicity tests were performed through the extract method on murine fibroblasts in order to verify if the presence of the silver coating affected the cellular viability and proliferation. Durability of the coating was also assessed, thus confirming the successful scaling up of the process, which will be therefore available for large-scale production. - Highlights: • Silver nanophases are increasingly used as effective antibacterial agent for biomedical applications. • Silver coatings were deposited on textiles through the in situ photo-reduction of a silver solution. • Flax fabrics were characterized from a biological and surface chemical point of view. • Scaling up of the process was confirmed.

  12. Vancomycin-modified Fe3O4@SiO2@Ag microflowers as effective antimicrobial agents

    Directory of Open Access Journals (Sweden)

    Wang C

    2017-04-01

    Full Text Available Chongwen Wang,1,2,* Kehan Zhang,2,* Zhe Zhou,2,* Qingjun Li,2 Liting Shao,2 Rong Zhang Hao,3 Rui Xiao,2 Shengqi Wang1,2 1College of Life Sciences & Bio-Engineering, Beijing University of Technology, 2Beijing Key Laboratory of New Molecular Diagnosis Technologies for Infectious Diseases, Beijing Institute of Radiation Medicine, Beijing, 3Institute for Disease Control and Prevention, Academy of Military Medical Sciences, Beijing, People’s Republic of China *These authors contributed equally to this work Abstract: Nanomaterials combined with antibiotics exhibit synergistic effects and have gained increasing interest as promising antimicrobial agents. In this study, vancomycin-modified magnetic-based silver microflowers (Van/Fe3O4@SiO2@Ag microflowers were rationally designed and prepared to achieve strong bactericidal ability, a wide antimicrobial spectrum, and good recyclability. High-performance Fe3O4@SiO2@Ag microflowers served as a multifunction-supporting matrix and exhibited sufficient magnetic response property due to their 200 nm Fe3O4 core. The microflowers also possessed a highly branched flower-like Ag shell that provided a large surface area for effective Ag ion release and bacterial contact. The modified-vancomycin layer was effectively bound to the cell wall of bacteria to increase the permeability of the cell membrane and facilitate the entry of the Ag ions into the bacterium, resulting in cell death. As such, the fabricated Van/Fe3O4@SiO2@Ag microflowers were predicted to be an effective and environment-friendly antibacterial agent. This hypothesis was verified through sterilization of Gram-negative Escherichia coli and Gram-positive methicillin-resistant Staphylococcus aureus, with minimum inhibitory concentrations of 10 and 20 µg mL-1, respectively. The microflowers also showed enhanced effect compared with bare Fe3O4@SiO2@Ag microflowers and free-form vancomycin, confirming the synergistic effects of the combination of the

  13. Immunological detection and quantification of DNA components structurally modified by alkylating carcinogens, mutagens and chemotherapeutic agents

    International Nuclear Information System (INIS)

    Rajewsky, M.F.

    1983-01-01

    The detection and quantification of defined reaction products of chemical mutagens and carcinogens (and of many cancer chemotherapeutic agents) with DNA require highly sensitive analytical techniques. The exceptional capability of immunoglobulins to recognize subtle alterations of molecular structure (especially when monoclonal antibodies are used to maximize specificity), outstanding sensitivity of immunoanalysis by high-affinity antibodies, and the fact that radioactively-labelled agents are not required suggest the utility of a radioimmunoassay to recognize and quantitate alkylated DNA products. We have recently developed a set of high-affinity monoclonal antibodies (secreted by mouse x mouse as well as by rat x rat hybridomas; antibody affinity constants, 10 9 to > 10 10 lmol) specifically directed against several DNA alkylation products with possible relevance in relation to both mutagenesis and malignant transformation of mammalian cells. These alkylation products include 0 6 -N-butyldeoxyguanosine, and 0 4 -ethyldeoxythymidine. When used in a radioimmunassay, an antibody specific for 0 6 -ethyldeoxyguanosine, for example, will detect this product at an 0 6 -ethyldeoxyguanosine/deoxyguanosine molar ratio of approx. 3 x 10 -7 in a hydrolysate of 100 ug of DNA. The limit of detection can be lowered further if the respective alkyldeoxynucleosides are separated by HPLC from the DNA hydrolysate prior to the RIA. The anti-alkyldeoxynucleoside monoclonal antibodies can also be used to visualize, by immunostaining and fluorescence microscopy combined with electronic image intensification, specific alkylation products in the nuclear DNA of individual cells, and to localize structurally modified bases in double-stranded DNA molecules by transmission electron microscopy

  14. Investigation of surface properties of physico-chemically modified natural fibres using inverse gas chromatography

    CSIR Research Space (South Africa)

    Cordeiro, N

    2011-01-01

    Full Text Available Inverse gas chromatography (IGC) is a suitable method to determine surface energy of natural fibres when compared to wetting techniques. In the present study, the surface properties of raw and modified lignocellulosic fibres have been investigated...

  15. Surface chemical and biological characterization of flax fabrics modified with silver nanoparticles for biomedical applications.

    Science.gov (United States)

    Paladini, F; Picca, R A; Sportelli, M C; Cioffi, N; Sannino, A; Pollini, M

    2015-01-01

    Silver nanophases are increasingly used as effective antibacterial agent for biomedical applications and wound healing. This work aims to investigate the surface chemical composition and biological properties of silver nanoparticle-modified flax substrates. Silver coatings were deposited on textiles through the in situ photo-reduction of a silver solution, by means of a large-scale apparatus. The silver-coated materials were characterized through X-ray Photoelectron Spectroscopy (XPS), to assess the surface elemental composition of the coatings, and the chemical speciation of both the substrate and the antibacterial nanophases. A detailed investigation of XPS high resolution regions outlined that silver is mainly present on nanophases' surface as Ag2O. Scanning electron microscopy and energy dispersive X-ray spectroscopy were also carried out, in order to visualize the distribution of silver particles on the fibers. The materials were also characterized from a biological point of view in terms of antibacterial capability and cytotoxicity. Agar diffusion tests and bacterial enumeration tests were performed on Gram positive and Gram negative bacteria, namely Staphylococcus aureus and Escherichia coli. In vitro cytotoxicity tests were performed through the extract method on murine fibroblasts in order to verify if the presence of the silver coating affected the cellular viability and proliferation. Durability of the coating was also assessed, thus confirming the successful scaling up of the process, which will be therefore available for large-scale production. Copyright © 2015 Elsevier B.V. All rights reserved.

  16. Surface modification of TiO2 nanoparticles via photocataliticaly induced reaction: Influence of functionality of silane coupling agent

    International Nuclear Information System (INIS)

    Tomovska, Radmila; Daniloska, Vesna; Asua, Jose M.

    2013-01-01

    Highlights: ► TiO 2 nanoparticles were modified by photocatalytic induced surface reaction. ► TiO 2 nanoparticles were subjects of modification and catalysts for the reaction. ► No cleavage of Si-C bond in silane coupling agent 3-triethoxysilyl propyl isocianate. ► High influence of functional group in silane on the Si-C cleavage was determined. ► Different electronegativity of the functionalities in the silane determines reaction way. - Abstract: In the present work the surface modification of TiO 2 nanoparticles by photocatalyticaly induced reaction with silane coupling agent 3-triethoxysilyl propyl isocianate (PIC) has been presented. It was demonstrated establishing of covalent Ti-O-Si bond between the nanoparticles and the PIC molecule. In comparison with previous results, it was demonstrated the high influence of the functional group from the silane coupling agent on the reaction course during surface functionalziation of TiO 2 nanoparticles. Depending on the amount and type (electronegativity of the end-functionalities) of the silane compound, high control of the surface characteristics of TiO 2 nanoparticles could be achieved.

  17. Evaluation of the bond strength of different adhesive agents to a resin-modified calcium silicate material (TheraCal LC).

    Science.gov (United States)

    Karadas, Muhammed; Cantekin, Kenan; Gumus, Husniye; Ateş, Sabit Melih; Duymuş, Zeynep Yesil

    2016-09-01

    This study evaluated the bond strength of different adhesive agents to TheraCal LC and mineral trioxide aggregate (MTA) and examined the morphologic changes of these materials with different surface treatments. A total of 120 specimens, 60 of MTA Angelus (AMTA), and 60 of TheraCal LC, were prepared and divided into six subgroups according to the adhesive agent used; these agents included Scotchbond Multipurpose, Clearfil SE Bond, Clearfil Protect Bond, Clearfil S 3 Bond, OptiBond All-in-One, and G-aenial Bond. After application of adhesive agents, Filtek Z250 composite resin was placed onto the specimens. Shear bond strengths were measured using a universal testing machine, followed by examination of the fractured surfaces. The surface changes of the specimens were observed using scanning electron microscopy. Data were compared by two-way analysis of variance. Although no significant differences were found among the bond strengths of different adhesives to AMTA (p = 0.69), a significant difference was found in terms of bond strengths of different adhesives to the TheraCal LC surface (p TheraCal LC compared to the bond with other adhesives. TheraCal LC bonded significantly more strongly than AMTA regardless of the adhesive agents tested. Resin-modified calcium silicate showed higher bond strength than AMTA in terms of the composite bond to these materials with different bonding systems. On the other hand, the highest shear bond-strength values were found for composite bonds with the combination of TheraCal LC and the total-etch adhesive system. SCANNING 38:403-411, 2016. © 2015 Wiley Periodicals, Inc. © Wiley Periodicals, Inc.

  18. Influence of the surface structure on the filtration performance of UV-modified PES membranes

    DEFF Research Database (Denmark)

    Kæselev, Bozena Alicja; Kingshott, P.; Jonsson, Gunnar Eigil

    2002-01-01

    Poly (ether sulfone) (PES) 50 kDa membranes were surface modified by irradiation with UV light (254 nm) in the presence of N-vinyl-2-pyrrolidine (NVP), 2-acrylamidoglycolic acid monohydrate (AAG) and 2-acrylamido-2-methyl-1-propanesulfonic acid (AAP). The surfaces of the modified membranes were c...

  19. Profilometric analysis of root surfaces after using various polishing agents

    Directory of Open Access Journals (Sweden)

    Anjan Jana

    2016-01-01

    Full Text Available Background: Polishing is an important step in oral prophylaxis procedure which retards further accumulation of plaque on the root surfaces. Though polishing was done with various abrasive particles with different sizes over a long period of time, it was never been highlighted to evaluate the ideal polishing material and the particle size that would produce the ideal surface smoothness (Ra 5 μm are not able to produce the surface smoothness <0.2 μm. Only, submicron sized particles are able to produce the desired smoothness.

  20. Effects of surface active agents on DNAPL migration and distribution in saturated porous media.

    Science.gov (United States)

    Cheng, Zhou; Gao, Bin; Xu, Hongxia; Sun, Yuanyuan; Shi, Xiaoqing; Wu, Jichun

    2016-11-15

    Dissolved surface active agents such as surfactant and natural organic matter can affect the distribution and fate of dense nonaqueous liquids (DNAPLs) in soil and groundwater systems. This work investigated how two common groundwater surface active agents, humic acid (HA) and Tween 80, affected tetrachloroethylene (PCE) migration and source zone architecture in saturated porous media under environmentally relevant conditions. Batch experiments were first conducted to measure the contact angles and interfacial tensions (IFT) between PCE and quartz surface in water containing different amount of surface active agents. Results showed that the contact angle increased and IFT decreased with concentration of surface active agent increasing, and Tween 80 was much more effective than HA. Five 2-D flow cell experiments were then conducted. Correspondingly, Tween 80 showed strong effects on the migration and distribution of PCE in the porous media due to its ability to change the medium wettability from water-wet into intermediate/NAPL-wet. The downward migration velocities of the PCE in three Tween 80 cells were slower than those in the other two cells. In addition, the final saturation of the PCE in the cells containing surface active agents was higher than that in the water-only cell. Results from this work indicate that the presence of surface active agents in groundwater may strongly affect the fate and distribution of DNAPL through altering porous medium wettability. Copyright © 2016 Elsevier B.V. All rights reserved.

  1. Enhancing osseointegration using surface-modified titanium implants

    Science.gov (United States)

    Yang, Y.; Oh, N.; Liu, Y.; Chen, W.; Oh, S.; Appleford, M.; Kim, S.; Kim, K.; Park, S.; Bumgardner, J.; Haggard, W.; Ong, J.

    2006-07-01

    Osseointegrated dental implants are used to replace missing teeth. The success of implants is due to osseointegration or the direct contact of the implant surface and bone without a fibrous connective tissue interface. This review discusses the enhancement of osseointegration by means of anodized microporous titanium surfaces, functionally macroporous graded titanium coatings, nanoscale titanium surfaces, and different bioactive factors.

  2. Multi-scale cell/surface interaction on modified titanium aluminum vanadium surfaces

    Science.gov (United States)

    Chen, Jianbo

    This dissertation presents a series of experimental studies of the effects of multi-scale cell/surface interactions on modified Ti-6Al-4V surfaces. These include laser-grooved surfaces; porous structures and RGD-coated laser-grooved surfaces. A nano-second DPSS UV lasers with a Gaussian pulse energy profile was used to introduce the desired micro-groove geometries onto Ti-6Al-4V surfaces. This was done without inducing micro-cracks or significant changes in surface chemistry within the heat affected zones. The desired 8-12 mum groove depths and widths were achieved by the control of pulse frequency, scan speed, and the lens focal length that controls spot size. The interactions between human osteosarcoma (HOS) cells and laser-grooved Ti-6Al-4V surfaces were investigated after 48 hours of cell culture. The cell behavior, including cell spreading, alignment and adhesion, was elucidated using scanning electronic microscopy (SEM), immuno-fluorescence staining and enzymatic detachment. Contact guidance was shown to increase as grooved spacing decreased. For the range of micro-groove geometries studied, micro-grooves with groove spacings of 20 mum provided the best combination of cell orientation and adhesion. Short-term adhesion experiments (15 mins to 1 day) also revealed that there is a positive correlation between cell orientation and cell adhesion. Contact guidance on the micro-grooved surfaces is shown to be enhanced by nano- and micro-scale asperities that provide sites for the attachment of lamellopodia during cell locomotion and spreading. Contact guidance is also promoted by the geometrical confinement provided by laser grooves. An experimental study of initial cell spreading and ingrowth into Ti-6Al-4V porous structures was also carried out on porous structures with different pore sizes and geometries. A combination of SEM, the tetrazolium salt (MTT) colorimetric assay and enzymatic detachment were used to study cell spreading and adhesion. The extent of cell

  3. Quantitative and Qualitative Analysis of Surface Modified Cellulose Utilizing TGA-MS

    Directory of Open Access Journals (Sweden)

    Daniel Loof

    2016-05-01

    Full Text Available With the aim to enhance interfacial adhesion of a hydrophobic polymer matrix and cellulosic fibers and fillers, chemical surface modifications with silane coupling agents are performed. Thermogravimetric analysis (TGA could be used to determine the degree of surface functionalization. However, similar thermal properties of treated and untreated cellulose hamper a precise determination of silane loading. This contribution deals with quantitative determination of silane loading combining both TGA and elemental analysis. Firstly, silane modified celluloses were studied by FT-IR, Raman, solid state NMR spectroscopy, and polarized light microscopy in order to determine functional groups and to study the impact of chemical treatment on cellulose morphology. Secondly, thermal stability and pyrolysis processes were studied by TG-MS analysis. In order to determine the exact silane loading, the mass percentages of the appropriate elements were quantified by elemental analysis and correlated with the charred residues determined by TGA yielding a linear dependency. With that correlation, it was possible to determine silane loadings for additional samples utilizing simple TGA measurements. The main advantage of that approach is that only one calibration is necessary for routine analyses of further samples and TGA-MS coupling gives additional information on thermal stability and pyrolysis routes, simultaneously.

  4. Aspects of silane coupling agents and surface conditioning in dentistry: an overview.

    Science.gov (United States)

    Lung, Christie Ying Kei; Matinlinna, Jukka Pekka

    2012-05-01

    To give an overview of aspects of silane coupling agents and surface conditioning in dentistry. Currently, silane coupling agents are used as adhesion promoters. Silanes are effective in enhancing adhesion between resin composite and silica-based ceramics. They do not bond effectively to non-silica based dental restorative materials. Surface conditioning of non-silica based ceramics with silica coating improves the bonding. This current overview will focus on the silane coupling agents: their properties, limitations in adhesion promotion and the clinical problems with the use of silanes. It will also focus on the current surface conditioning methods as well as new surface conditioning techniques to enhance the bonding through conventional silanization approaches. Several surface conditioning methods are being used clinically to enhance the adhesion of resin composites to non-silica based restorative materials. Other approaches are under investigation. The clinical problem of using silanes in adhesion promotion is the bond degradation over time in oral environment. The current silane coupling agents are not ideal. The current silane coupling agents can fulfill the minimum requirements in clinical practice to enhance the bonding of resin composite to dental restorative materials. Developments of novel surface conditioning methods and silane coupling agents are required to address the bond durability problem. Copyright © 2012 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  5. Selected anionic and cationic surface active agents: case study on the Kłodnica sediments

    Directory of Open Access Journals (Sweden)

    Olkowska Ewa

    2017-03-01

    Full Text Available Surface active agents (surfactants are a group of chemical compounds, which are used as ingredients of detergents, cleaning products, cosmetics and functional products. After use, wastes containing surfactants or their degradation products are discharged to wastewater treatment plants or directly into surface waters. Due to their specific properties of SAAs, compounds are able to migrate between different environmental compartments such as soil, sediment, water or even living organisms and accumulate there. Surfactants can have a harmful effect on living organisms. They can connect with bioactive molecules and modify their function. Additionally, they have the ability to migrate into cells and cause their damage or death. For these reasons investigation of individual surfactants should be conducted. The presented research has been undertaken to obtain information about SAA contamination of sediment from the River Kłodnica catchment caused by selected anionic (linear alkylbenzene sulfonates (LAS C10-C13 and cationic (alkylbenzyldimethylammonium (BDMA-C12-16, alkyl trimethyl ammonium (DTMA, hexadecyl piridinium chloride (HP chlorides surfactants. This river flows through an area of the Upper Silesia Industrial Region where various companies and other institutions (e.g. coal mining, power plants, metallurgy, hospitals are located. To determine their concentration the following analytical tools have been applied: accelerated solvent extraction– solid phase extraction – high performance liquid chromatography – UV-Vis (anionic SAAs and conductivity (cationic SAAs detectors. In all sediments anionic SAAs have been detected. The concentrations of HTMA and BDMA-C16 in tested samples were higher than other cationic analytes. Generally, levels of surfactants with longer alkyl chains were higher and this observation can confirm their higher susceptibility to sorption on solid surfaces.

  6. End-functional silicone coupling agent modified PEO/P(VDF-HFP)/SiO2 nanocomposite polymer electrolyte DSSC

    International Nuclear Information System (INIS)

    Zhang Jing; Yang Ying; Wu Sujuan; Xu Sheng; Zhou Conghua; Hu Hao; Chen Bolei; Xiong Xiaodong; Sebo, Bobby; Han Hongwei; Zhao Xingzhong

    2008-01-01

    The end-functional silicone coupling agent (dodecyl-trimethoxysilane, DTMS for short) was used to modify the PEO/P(VDF-HFP)/SiO 2 nanocomposite polymer electrolyte (CPE) and the different amounts of DTMS modification effects were studied. The experiments showed the silicone coupling agent with hydrophobic alkyl chains (-C 12 H 25 ) chemically engineered on the SiO 2 nanoparticles, and formed a Si-O-Si cross-linked network in the new nanocomposite polymer electrolyte. Proper content of DTMS modified CPE exhibited improved ionic conductivity and the connection with the photoanode and counter electrode. However, much higher content of the DTMS modification changed the conformation of the polymer network and reduced the ionic movement. Compared with the performance (3.84%) of the original DSSC, the DSSC with functional silicone coupling agent modified CPE (DTMS:SiO 2 = 2:1, mol ratio) exhibited improved J sc (7.94 mA cm -2 ), V oc (0.624 V) and optimal efficiency (5.2%) (measured at AM1.5, light intensity of 58.4 mW cm -2 ). The V oc of the silicone coupling agent modified polymer electrolyte DSSC is obviously improved, which is mainly due to that the hydrophobic alkyl chain end groups formed an insulating layer that retarded the electron recombination at the TiO 2 nanoporous photoanode/polymer electrolyte interface. The DTMS:SiO 2 = 2:1 modified CPE type DSSC exhibited a performance of 6.42% at a light intensity of 32.1 mW cm -2 and 4.94% at 99.2 mW cm -2

  7. Modified surface testing method for large convex aspheric surfaces based on diffraction optics.

    Science.gov (United States)

    Zhang, Haidong; Wang, Xiaokun; Xue, Donglin; Zhang, Xuejun

    2017-12-01

    Large convex aspheric optical elements have been widely applied in advanced optical systems, which have presented a challenging metrology problem. Conventional testing methods cannot satisfy the demand gradually with the change of definition of "large." A modified method is proposed in this paper, which utilizes a relatively small computer-generated hologram and an illumination lens with certain feasibility to measure the large convex aspherics. Two example systems are designed to demonstrate the applicability, and also, the sensitivity of this configuration is analyzed, which proves the accuracy of the configuration can be better than 6 nm with careful alignment and calibration of the illumination lens in advance. Design examples and analysis show that this configuration is applicable to measure the large convex aspheric surfaces.

  8. Influence of abutment height and surface roughness on in vitro retention of three luting agents.

    Science.gov (United States)

    Cano-Batalla, Jordi; Soliva-Garriga, Joan; Campillo-Funollet, Marc; Munoz-Viveros, Carlos A; Giner-Tarrida, Lluis

    2012-01-01

    This study evaluated the effects of abutment height, airborne-particle abrasion, and type of cement on the tensile resistance to dislodgement of cement-retained implant restorations. Three groups of 12 standardized abutments each were prepared with different heights (4 mm, 5 mm, and 6 mm) using a milling machine. Crowns were cast in cobalt-chrome using the lost-wax technique, airborne particle-abraded using 50-Μm aluminum oxide, and cleaned with acetone. Restorations were cemented using a noneugenol acrylic urethane cement, a resin-modified glass ionomer, or a zinc oxide-noneugenol cement. A 5-kg load was applied for 10 minutes. Samples were kept at 37°C and 100% humidity overnight. A tensile force was applied to the crown using a testing machine at a crosshead speed of 5 mm/minute until failure occurred. Next, the abutments were airborne particle-abraded with 50-Μm aluminum oxide, and the cementation and testing procedures were repeated. The effects of cement, abutment height, and surface treatment were evaluated statistically. There were significant differences among the cements. The resin-modified glass ionomer provided the greatest retention in all the tested conditions, while the zinc oxide-noneugenol cement produced the lowest retention values. Significant differences were also detected between 4-mm and 6-mm abutments, with the 6-mm abutments being more retentive. No differences were found between 4-mm and 5-mm abutments or between 5-mm and 6-mm abutments. The effect of airborne-particle abrasion was also found to be significant. A maximum increase of 90 N in retention force was observed after airborne-particle abrasion for the 5-mm abutments cemented with the acrylic urethane cement. Cement, airborne-particle abrasion, and abutment height can significantly influence retention of implant-supported crowns. Different parameters, including those specific to the patient, should be considered in the selection of a luting agent.

  9. Alignment of liquid crystals : on geometrically and chemically modified surfaces

    NARCIS (Netherlands)

    Zhang, J.

    2013-01-01

    This thesis consists of two main parts. The first part describes a new model to explain the complex role of surface materials and surface geometry in the liquid crystal (LC) alignment, which has been a subject of intensive debate over the last 40 years. The second part presents a potentially cost

  10. Bond strength of three luting agents to zirconia ceramic - influence of surface treatment and thermocycling

    Directory of Open Access Journals (Sweden)

    Ahmed Attia

    2011-08-01

    Full Text Available OBJECTIVE: This in vitro study aimed to evaluate the influence of different surface treatments, 3 luting agents and thermocycling on microtensile bond strength (µTBS to zirconia ceramic. Material and METHODS: A total of 18 blocks (5x5x4 mm were fabricated from zirconia ceramic (ICE Zirkonia and duplicated into composite blocks (Alphadent. Ceramic blocks were divided into 3 groups (n=6 according to the following surface treatments: airborne-particle abrasion (AA, silica-coating, (SC (CoJet and silica coating followed by silane application (SCSI (ESPE Sil. Each group was divided into 3 subgroups (n=2 according to the 3 luting agents used. Resin-modified glass-ionomer cement (RMGIC, Ketac Cem Plus, self-adhesive resin cement (UN, RelyX Unicem and adhesive resin cement (ML, MultiLink Automix were used for bonding composite and zirconia blocks. Each bonding assembly was cut into microbars (10 mm long and 1±0.1 mm². Seven specimens of each subgroup were stored in water bath at 37ºC for 1 week. The other 7 specimens were stored in water bath at 37ºC for 30 days then thermocycled (TC for 7,500 cycles. µTBS values were recorded for each specimen using a universal testing machine. Statistical analyses were performed using a 3-way ANOVA model followed by serial 1-way ANOVAs. Comparison of means was performed with Tukey's HSD test at (α=0.05. RESULTS: µTBS ranged from 16.8 to 31.8 MPa after 1 week and from 7.3 to 16.4 MPa after 30 days of storage in water and thermocycling. Artificial aging significantly decreased µTBS (p<0.05. Considering surface treatment, SCSI significantly increased µTBS (p<0.05 compared to SC and AA. Resin cements (UN and ML demonstrated significantly higher µTBS (p<0.05 compared to RMGIC cement. CONCLUSIONS: Silica coating followed by silane application together with adhesive resin cements significantly increased µTBS, while thermocycling significantly decreased µTBS.

  11. Bond strength of three luting agents to zirconia ceramic - Influence of surface treatment and thermocycling

    Science.gov (United States)

    ATTIA, Ahmed

    2011-01-01

    Objective This in vitro study aimed to evaluate the influence of different surface treatments, 3 luting agents and thermocycling on microtensile bond strength (µTBS) to zirconia ceramic. Material and Methods A total of 18 blocks (5x5x4 mm) were fabricated from zirconia ceramic (ICE Zirkonia) and duplicated into composite blocks (Alphadent). Ceramic blocks were divided into 3 groups (n=6) according to the following surface treatments: airborne-particle abrasion (AA), silica-coating, (SC) (CoJet) and silica coating followed by silane application (SCSI) (ESPE Sil). Each group was divided into 3 subgroups (n=2) according to the 3 luting agents used. Resin-modified glass-ionomer cement (RMGIC, Ketac Cem Plus), self-adhesive resin cement (UN, RelyX Unicem) and adhesive resin cement (ML, MultiLink Automix) were used for bonding composite and zirconia blocks. Each bonding assembly was cut into microbars (10 mm long and 1±0.1 mm2). Seven specimens of each subgroup were stored in water bath at 37ºC for 1 week. The o ther 7 specimens were stored in water bath at 37ºC for 30 days then thermocycled (TC) for 7,500 cycles. µTBS values were recorded for each specimen using a universal testing machine. Statistical analyses were performed using a 3-way ANOVA model followed by serial 1-way ANOVAs. Comparison of means was performed with Tukey's HSD test at (α=0.05). Results µTBS ranged from 16.8 to 31.8 MPa after 1 week and from 7.3 to 16.4 MPa after 30 days of storage in water and thermocycling. Artificial aging significantly decreased µTBS (p<0.05). Considering surface treatment, SCSI significantly increased µTBS (p<0.05) compared to SC and AA. Resin cements (UN and ML) demonstrated significantly higher µTBS (p<0.05) compared to RMGIC cement. Conclusions Silica coating followed by silane application together with adhesive resin cements significantly increased µTBS, while thermocycling significantly decreased µTBS. PMID:21710091

  12. Copper hexacyanoferrate formation on the modified silica surface with DAB-Am-16 dendrimer

    International Nuclear Information System (INIS)

    Carmo, Devaney R. do; Gabriel Junior, Suelino; Bicalho, Urquisa O.; Paim, Leonardo L.

    2009-01-01

    The dendrimer hexadecamine poly(propylene)imine (DAB-Am-16) of third generation (G-3) was anchored on the silica gel surface. The modified silica interact easily with Cu 2+ and then with hexacyanoferrate to form copper hexacyanoferrate. The modified silica was characterized by following techniques: nuclear magnetic resonance (NMR), infrared (FTIR), energy dispersive X-ray (EDX) and cyclic voltammetry. As application of the composite obtained, the modified silica containing copper hexacyanoferrate (CuHCFSD) was tested for a voltammetric determination of nitrite using a graphite paste modified electrode. The modified graphite paste electrode can be applied also to the determination of others biological substances with success. (author)

  13. Effect of laser modified surface microtopochemistry on endothelial cell growth.

    Science.gov (United States)

    Duncan, A C; Rouais, F; Lazare, S; Bordenave, L; Baquey, Ch

    2007-02-15

    The introduction of microelectronics technology in the area of biological sciences has brought forth previously unforeseeable applications such as DNA or protein biochips, miniaturized, multiparametric biosensors for high performance multianalyte assays, DNA sequencing, biocomputers, and substrates for controlled cell growth (i.e. tissue engineering). We developed and investigated a new method using "cold" excimer laser beam technology combined with microlithographical techniques to create surfaces with well defined 3D microdomains in order to delineate critical microscopic surface features governing cell-material interactions. Microfabricated surfaces with microgrooves 30-3 microm deep, 10 - 1 microm wide spaced 30 microm apart were obtained with micron resolution, by "microsculpturing" polymer model surfaces using a computer controlled laser KrF excimer beam coupled with a microlithographic projection technique. The laser beam after exiting a mask was focused onto the polymer target surface via an optical setup allowing for a 10-fold reduction of the mask pattern. Various 3D micropatterned features were obtained at the micron level. Reproducible submicron features could also be obtained using this method. Subsequently, model human umbilical endothelial cells (HUVEC) were cultured on the laser microfabricated surfaces in order to study the effects of specific microscopic surface features on cell deposition and orientation. Cell deposition patterns were found to be microstructure dependant, and showed cell orientation dependency for features in the cell range dimension, a behaviour significantly different from that of a previously studied cell model (osteoprogenitor cell). This model may be a promising in so far as it is very rapid (a time frame less than a second per square centimeter of micropatterned surface) and provides further insights into the effects of surface microtopography on cell response with possible applications in the field of biosensors

  14. MICROBIAL SURFACE-ACTIVE SUBSTANCES AS ANTIADHESIVE AGENTS

    Directory of Open Access Journals (Sweden)

    T. P. Pirog

    2016-06-01

    Full Text Available The literature data of recent years about capacity of biosurfactants synthesized by bacteria (Pseudomonas, Lactobacillus, Bacillus and fungi (Candida, Trichosporon, Saccharomyces not only to avert the adhesion of microorganisms on the different materials, but also to destroy formed biofilms on them were presented. The perspective of biosurfactants to prevent pathogens colonization on biotic and abiotic surfaces, that is known, can be a reason of cause and spread of infectious diseases was discussed. The data of our researches about antiadhesive properties of biosurfactants synthesized by Acinetobacter calcoaceticus IMV B-7241, Nocardia vaccinni IMV B-7405 and Rhodococcus erythropolis IMV Ac-5017 were presented.

  15. A Strontium-Modified Titanium Surface Produced by a New Method and Its Biocompatibility In Vitro.

    Directory of Open Access Journals (Sweden)

    Chundong Liu

    Full Text Available To present a new and effective method of producing titanium surfaces modified with strontium and to investigate the surface characteristics and in vitro biocompatibility of titanium (Ti surfaces modified with strontium (Sr for bone implant applications.Sr-modified Ti surfaces were produced by sequential treatments with NaOH, strontium acetate, heat and water. The surface characteristics and the concentration of the Sr ions released from the samples were examined. Cell adhesion, morphology and growth were investigated using osteoblasts isolated from the calvaria of neonatal Sprague-Dawley rats. Expression of osteogenesis-related genes and proteins was examined to assess the effect of the Sr-modified Ti surfaces on osteoblasts.The modified titanium surface had a mesh structure with significantly greater porosity, and approximately5.37±0.35at.% of Sr was incorporated into the surface. The hydrophilicity was enhanced by the incorporation of Sr ions and water treatment. The average amounts of Sr released from the Sr-modified plates subjected to water treatment were slight higher than the plates without water treatment. Sr promoted cellular adhesion, spreading and growth compared with untreated Ti surfaces. The Sr-modified Ti plates also promoted expression of osteogenesis-related genes,and expression of OPN and COL-І by osteoblasts. Ti plates heat treated at 700°C showed increased bioactivity in comparison with those treated at 600°C. Water treatment upregulated the expression of osteogenesis-related genes.These results show that Sr-modification of Ti surfaces may improve bioactivity in vitro. Water treatment has enhanced the response of osteoblasts. The Sr-modified Ti heat-treated at 700°C exhibited better bioactivity compared with that heated at 600°C.

  16. A Strontium-Modified Titanium Surface Produced by a New Method and Its Biocompatibility In Vitro.

    Science.gov (United States)

    Liu, Chundong; Zhang, Yanli; Wang, Lichao; Zhang, Xinhua; Chen, Qiuyue; Wu, Buling

    2015-01-01

    To present a new and effective method of producing titanium surfaces modified with strontium and to investigate the surface characteristics and in vitro biocompatibility of titanium (Ti) surfaces modified with strontium (Sr) for bone implant applications. Sr-modified Ti surfaces were produced by sequential treatments with NaOH, strontium acetate, heat and water. The surface characteristics and the concentration of the Sr ions released from the samples were examined. Cell adhesion, morphology and growth were investigated using osteoblasts isolated from the calvaria of neonatal Sprague-Dawley rats. Expression of osteogenesis-related genes and proteins was examined to assess the effect of the Sr-modified Ti surfaces on osteoblasts. The modified titanium surface had a mesh structure with significantly greater porosity, and approximately5.37±0.35at.% of Sr was incorporated into the surface. The hydrophilicity was enhanced by the incorporation of Sr ions and water treatment. The average amounts of Sr released from the Sr-modified plates subjected to water treatment were slight higher than the plates without water treatment. Sr promoted cellular adhesion, spreading and growth compared with untreated Ti surfaces. The Sr-modified Ti plates also promoted expression of osteogenesis-related genes,and expression of OPN and COL-І by osteoblasts. Ti plates heat treated at 700°C showed increased bioactivity in comparison with those treated at 600°C. Water treatment upregulated the expression of osteogenesis-related genes. These results show that Sr-modification of Ti surfaces may improve bioactivity in vitro. Water treatment has enhanced the response of osteoblasts. The Sr-modified Ti heat-treated at 700°C exhibited better bioactivity compared with that heated at 600°C.

  17. The constitution and microstructure of laser surface-modified metals

    Science.gov (United States)

    Singh, Jogender

    1992-09-01

    The applications oflasers in the processing of metals, ceramics, and semiconductors range from surface glazing of thin films on semiconductors to thick surface cladding on metals. Lasers have the unique capability of rapid heating, melting, and quenching of the substrate, which results in the formation of new engineering materials with metastable microstructures. This article describes the microstructural evolution of laser-glazed and laser-clad alloys treated with a pulse or continuous-wave CO2 laser.

  18. Blocked-micropores, surface functionalized, bio-compatible and silica-coated iron oxide nanocomposites as advanced MRI contrast agent

    International Nuclear Information System (INIS)

    Darbandi, Masih; Laurent, Sophie; Busch, Martin; Li Zian; Yuan Ying; Krüger, Michael; Farle, Michael; Winterer, Markus; Vander Elst, Luce; Muller, Robert N.; Wende, Heiko

    2013-01-01

    Biocompatible magnetic nanoparticles have been found promising in several biomedical applications for tagging, imaging, sensing and separation in recent years. In this article, a systematic study of the design and development of surface-modification schemes for silica-coated iron oxide nanoparticles (IONP) via a one-pot, in situ method at room temperature is presented. Silica-coated IONP were prepared in a water-in-oil microemulsion, and subsequently the surface was modified via addition of organosilane reagents to the microemulsion system. The structure and the morphology of the as synthesized nanoparticles have been investigated by means of transmission electron microscopy (TEM) and measurement of N 2 adsorption–desorption. Electron diffraction and high-resolution transmission electron microscopic (TEM) images of the nanoparticles showed the highly crystalline nature of the IONP structures. Nitrogen adsorption indicates microporous and blocked-microporous structures for the silica-coated and amine functionalized silica-coated IONP, respectively which could prove less cytotoxicity of the functionalized final product. Besides, the colloidal stability of the final product and the presence of the modified functional groups on top of surface layer have been proven by zeta-potential measurements. Owing to the benefit from the inner IONP core and the hydrophilic silica shell, the as-synthesized nanocomposites were exploited as an MRI contrast enhancement agent. Relaxometric results prove that the surface functionalized IONP have also signal enhancement properties. These surface functionalized nanocomposites are not only potential candidates for highly efficient contrast agents for MRI, but could also be used as ultrasensitive biological-magnetic labels, because they are in nanoscale size, having magnetic properties, blocked-microporous and are well dispersible in biological environment.

  19. Surface activity and molecular characteristics of cuttlefish skin gelatin modified by oxidized linoleic acid

    NARCIS (Netherlands)

    Aewsiri, T.; Benjakul, S.; Visessanguan, W.; Wierenga, P.A.; Gruppen, H.

    2011-01-01

    Surface activity and molecular changes of cuttlefish skin gelatin modified with oxidized linoleic acid (OLA) prepared at 60, 70 and 80 °C at different times were investigated. Modification of gelatin with OLA could improve surface activity of resulting gelatin as evidenced by the decreased surface

  20. Modulating Protein Adsorption on Oxygen Plasma Modified Polysiloxane Surfaces

    International Nuclear Information System (INIS)

    Marletta, G.

    2006-01-01

    In the present paper we report the study on the adsorption behaviour of three model globular proteins, Human Serum Albumin, Lactoferrin and Egg Chicken Lysozyme onto both unmodified surfaces of a silicon-based polymer and the corresponding plasma treated surfaces. In particular, thin films of hydrophobic polysiloxane (about 90 degree of static water contact angle, WCA) were converted by oxygen plasma treatment at reduced pressure into very hydrophilic phases of SiOx (WCA less than 5 degree). The kinetics of protein adsorption processes were investigated by QCM-D technique, while the chemical structure and topography of the protein adlayer have been studied by Angular resolved-XPS and AFM respectively. It turned out that Albumin and Lysozyme exhibited the opposite preferential adsorption respectively onto the hydrophobic and hydrophilic surfaces, while Lactoferrin did not exhibit significant differences. The observed protein behaviour are discussed both in terms of surface-dependent parameters, including surface free energy and chemical structure, and in terms of protein-dependent parameters, including charge as well as the average molecular orientation in the adlayers. Finally, some examples of differential adsorption behaviour of the investigated proteins are reported onto nanopatterned polysiloxane surfaces consisting of hydrophobic nanopores surrounded by hydrophilic (plasma-treated) matrix and the reverse

  1. Modeling of adsorption of toxic chromium on natural and surface modified lightweight expanded clay aggregate (LECA)

    Energy Technology Data Exchange (ETDEWEB)

    Kalhori, Ebrahim Mohammadi, E-mail: zarrabi62@yahoo.com [Department of Environmental Health Engineering, Faculty of Health, Alborz University of Medical Sciences, P.O. Box No: 31485/561, Alborz, Karaj (Iran, Islamic Republic of); Yetilmezsoy, Kaan, E-mail: yetilmez@yildiz.edu.tr [Department of Environmental Engineering, Faculty of Civil Engineering, Yildiz Technical University, 34220 Davutpasa, Esenler, Istanbul (Turkey); Uygur, Nihan, E-mail: uygur.n@gmail.com [Department of Environmental Engineering, Faculty of Engineering, Adiyaman University, 02040 Altinsehir, Adiyaman (Turkey); Zarrabi, Mansur, E-mail: mansor62@gmail.com [Department of Environmental Health Engineering, Faculty of Health, Alborz University of Medical Sciences, P.O. Box No: 31485/561, Alborz, Karaj (Iran, Islamic Republic of); Shmeis, Reham M. Abu, E-mail: r.abushmeis@yahoo.com [Department of Basic Pharmaceutical Sciences, Faculty of Pharmacy, Isra University, PO Box 140753, code 11814, Amman (Jordan)

    2013-12-15

    Lightweight Expanded Clay Aggregate (LECA) modified with an aqueous solution of magnesium chloride MgCl{sub 2} and hydrogen peroxide H{sub 2}O{sub 2} was used to remove Cr(VI) from aqueous solutions. The adsorption properties of the used adsorbents were investigated through batch studies, Scanning Electron Microscopy (SEM), X-ray Diffraction (XRD), X-ray Fluorescence Spectroscopy (XRF), and Fourier Transform Infrared (FTIR) spectroscopy. The effect created by magnesium chloride on the modification of the LECA surface was greater than that of hydrogen peroxide solution and showed a substantial increase in the specific surface area which has a value of 76.12 m{sup 2}/g for magnesium chloride modified LECA while the values of 53.72 m{sup 2}/g, and 11.53 m{sup 2}/g were found for hydrogen peroxide modified LECA and natural LECA, respectively. The extent of surface modification with enhanced porosity in modified LECA was apparent from the recorded SEM patterns. XRD and FTIR studies of themodified LECA surface did not show any structural distortion. The adsorption kinetics was found to follow the modified Freundlich kinetic model and the equilibrium data fitted the Sips and Dubinin-Radushkevich equations better than other models. Maximum sorption capacities were found to be 198.39, 218.29 and 236.24 mg/g for natural LECA, surface modified LECA with H{sub 2}O{sub 2} and surface modified LECA with MgCl{sub 2}, respectively. Adsorbents were found to have only a weak effect on conductivity and turbidity of aqueous solutions. Spent natural and surface modified LECA with MgCl{sub 2} was best regenerated with HCl solution, while LECA surface modified with H{sub 2}O{sub 2} was best regenerated with HNO{sub 3} concentrated solution. Thermal method showed a lower regeneration percentage for all spent adsorbents.

  2. Studies on a surface acoustic wave (SAW) dosimeter sensor for organophosphorous nerve agents

    NARCIS (Netherlands)

    Nieuwenhuizen, M.S.; Harteveld, J.L.N.

    1997-01-01

    As a follow-up of previous work on a Surface Acoustic Wave (SAW) sensor for nerve agents, irreversible response effects have been studied in more detail. Surface analytical studies indicated that degradation products are responsible for the effects observed. In addition it was tried to explore these

  3. Preparation and Evaluation of Surface Modified Lactose Particles for Improved Performance of Fluticasone Propionate Dry Powder Inhaler.

    Science.gov (United States)

    Singh, Deepak J; Jain, Rajesh R; Soni, P S; Abdul, Samad; Darshana, Hegde; Gaikwad, Rajiv V; Menon, Mala D

    2015-08-01

    Dry powder inhalers (DPI) are generally formulated by mixing micronized drug particles with coarse lactose carrier particles to assist powder handling during the manufacturing and powder aerosol delivery during patient use. In the present study, surface modified lactose (SML) particles were produced using force control agents, and their in vitro performance on dry powder inhaler (DPI) formulation of Fluticasone propionate was studied. With a view to reduce surface passivation of high surface free energy sites on the most commonly used DPI carrier, α- lactose monohydrate, effects of various force control agents such as Pluronic F-68, Cremophor RH 40, glyceryl monostearate, polyethylene glycol 6000, magnesium stearate, and soya lecithin were studied. DPI formulations prepared with SML showed improved flow properties, and atomic force microscopy (AFM) studies revealed decrease in surface roughness. The DSC and X-ray diffraction patterns of SML showed no change in the crystal structure and thermal behavior under the experimental conditions. The fine particle fraction (FPF) values of lactose modified with Pluronic F-68, Cremophor RH 40, glyceryl monostearate were improved, with increase in concentration up to 0.5%. Soya lecithin and PEG 6000 modified lactose showed decrease in FPF value with increase in concentration. Increase in FPF value was observed with increasing concentration of magnesium stearate. Two different DPI devices, Rotahaler(®) and Diskhaler(®), were compared to evaluate the performance of SML formulations. FPF value of all SML formulations were higher using both devices as compared to the same formulations prepared using untreated lactose. One month stability of SML formulations at 40°C/75% RH, in permeable polystyrene tubes did not reveal any significant changes in FPF values. SML particles can help in reducing product development hindrances and improve inhalational properties of DPI.

  4. Chemical switches and logic gates based on surface modified semiconductors

    Energy Technology Data Exchange (ETDEWEB)

    Konrad, Szacilowski; Wojciech, Macyk [Jagiellonian Univ., Dept. of Chemistry, Krakow (Poland)

    2006-02-15

    Photoelectrochemical properties of multicomponent photo-electrodes based on titanium dioxide and cadmium sulfide powders modified with hexacyanoferrate complexes have been examined. Photocurrent responses were recorded as functions of applied potential and photon energy. Surprisingly, the photocurrent can be switched between positive and negative values as a result of potential or photon energy changes. This new effect called Photo Electrochemical Photocurrent Switching (PEPS) opens a possibility of new chemical switches and logic gates construction. Boolean logic analysis and a tentative mechanism of the device are discussed. (authors)

  5. In Vitro Analysis of Fibronectin-Modified Titanium Surfaces

    Science.gov (United States)

    Chang, Yu-Chi; Lee, Wei-Fang; Feng, Sheng-Wei; Huang, Haw-Ming; Lin, Che-Tong; Teng, Nai-Chia; Chang, Wei Jen

    2016-01-01

    Background Glow discharge plasma (GDP) procedure is an effective method for grafting various proteins, including albumin, type I collagen, and fibronectin, onto a titanium surface. However, the behavior and impact of titanium (Ti) surface modification is yet to be unraveled. Purpose The purpose of this study is to evaluate and analyze the biological properties of fibronectin-grafted Ti surfaces treated by GDP. Materials and Methods Grade II Ti discs were initially cleaned and autoclaved to obtain original specimens. Subsequently, the specimens were GDP treated and grafted with fibronectin to form Ar-GDP (Argon GDP treatment only) and GDP-fib (fibronectin coating following GDP treatment) groups. Blood coagulation test and MG-63 cell culture were performed to evaluate the biological effects on the specimen. Results There was no significant difference between Ar-GDP and GDP-fib groups in blood compatibility analysis. While in the MTT test, cellular proliferation was benefited from the presence of fibronectin coating. The numbers of cells on Ar-GDP and GDP-fib specimens were greater than those in the original specimens after 24 h of culturing. Conclusions GDP treatment combined with fibronectin grafting favored MG-63 cell adhesion, migration, and proliferation on titanium surfaces, which could be attributed to the improved surface properties. PMID:26731536

  6. Chemical Warfare Agent Surface Adsorption: Hydrogen Bonding of Sarin and Soman to Amorphous Silica.

    Science.gov (United States)

    Davis, Erin Durke; Gordon, Wesley O; Wilmsmeyer, Amanda R; Troya, Diego; Morris, John R

    2014-04-17

    Sarin and soman are warfare nerve agents that represent some of the most toxic compounds ever synthesized. The extreme risk in handling such molecules has, until now, precluded detailed research into the surface chemistry of agents. We have developed a surface science approach to explore the fundamental nature of hydrogen bonding forces between these agents and a hydroxylated surface. Infrared spectroscopy revealed that both agents adsorb to amorphous silica through the formation of surprisingly strong hydrogen-bonding interactions with primarily isolated silanol groups (SiOH). Comparisons with previous theoretical results reveal that this bonding occurs almost exclusively through the phosphoryl oxygen (P═O) of the agent. Temperature-programmed desorption experiments determined that the activation energy for hydrogen bond rupture and desorption of sarin and soman was 50 ± 2 and 52 ± 2 kJ/mol, respectively. Together with results from previous studies involving other phosphoryl-containing molecules, we have constructed a detailed understanding of the structure-function relationship for nerve agent hydrogen bonding at the gas-surface interface.

  7. Novel surface display system for proteins on non-genetically modified gram-positive bacteria

    NARCIS (Netherlands)

    Bosma, T; Kanninga, R; Neef, J; Audouy, SAL; van Roosmalen, ML; Steen, A; Buist, G; Kok, J; Kuipers, OP; Robillard, G; Leenhouts, K

    A novel display system is described that allows highly efficient immobilization of heterologous proteins on bacterial surfaces in applications for which the use of genetically modified bacteria is less desirable. This system is based on nonliving and non-genetically modified gram-positive bacterial

  8. Physico-chemical characterisation of surface modified particles for inhalation.

    Science.gov (United States)

    Stank, Katharina; Steckel, Hartwig

    2013-05-01

    Surface modification of drugs for inhalation is a possibility to influence interparticulate forces. This can be necessary to achieve a sufficient aerosolisation during powder inhalation as the cohesiveness of the micronised drug can be reduced. In addition, the interaction with propellants in pressurised metered dose inhaler can be changed. This can be used to improve the physical stability of the suspension based formulations. A dry particle coating process was used for the alteration of particle surfaces. The blending of micronised salbutamol sulphate (SBS) with different concentrations of magnesium stearate (Mgst) or glycerol monostearate (GMS) was followed by co-milling with an air jet mill. The powder properties were characterised by SEM, EDX, laser diffraction, BET and inverse gas chromatography. Physical mixtures generated by Turbula blending were compared to co-milled samples. A slight particle size reduction was determined. The Mgst deposition on SBS particles was detected by EDX measurements. The dispersive surface energy of SBS is lowered and the energy distribution is more homogenous for the co-milled samples. This study proves the application of co-milling for surface modification in the inhalation area. Copyright © 2013 Elsevier B.V. All rights reserved.

  9. Efficiency of surface modified Ti coated with copper nanoparticles to ...

    Indian Academy of Sciences (India)

    Abstract. Titanium (Ti) used as condenser material in nuclear power plants encounter severe biofouling in marine environment which in turn affects the efficiency of the metal. To reduce the biofouling by marine microorganisms, surface modification of the Ti was carried out by anodization process to obtain nanotubes ...

  10. Surface characterization of silver and palladium modified glassy ...

    Indian Academy of Sciences (India)

    WINTEC

    Abstract. In this work, the influence of silver and palladium on the surface of undoped, boron doped and phosphorus doped glassy carbon has been studied. The silver and palladium concentrations in solution, after metal deposition, were measured by atomic absorption spectrophotometer. The morphology of metal coatings.

  11. Modified hot-conditioning of PHT system surfaces of PHWRs

    International Nuclear Information System (INIS)

    Venkateswaran, G.

    1997-01-01

    The increased awareness on the importance of controlling activity transport and radiation buildup on out-of-core surfaces of water cooled nuclear reactors is leading to a host of measures both from chemistry as well as engineering sides being undertaken. Passivation of the surfaces of structural materials is one such. Pressurised Heavy Water Reactors of CANDU design use large surface area of carbon steel alloy in the Primary Heat Transport System. Hot-conditioning of the PHT system with deoxygenated light water at temperatures ≅ 473 - 523 K during commissioning stage is done to form a protective magnetite film on the surfaces of carbon steel essentially to guard this material from corrosion during the intervening period between initial commissioning and first fuel loading and achieving nuclear heat. However, a need is felt to improve the quality of this magnetite film and control the crud release so that the twin objectives of controlling the corrosion of carbon steel and reducing a possible deposition of corrosion products on surfaces of fuel clad could be achieved. Laboratory static autoclave investigations have been carried out on the formation of protective magnetite film on carbon steel at 473 K, pH 10 (pH at 298 K) deoxygenated aqueous solutions of chelants like HEDTA, DTPA, NTA apart from EDTA. Additionally, influence of AVT chemicals like hydrazine, cyclohexylamine, morpholine and additives like glucose, boric acid has been studied. The data have been compared with the standard procedure of hot-conditioning namely with simple LiOH. It is found that chelants increase the base metal loss but the oxide formed is more protective than the one formed under simple LiOH treatment. The efficiency of passivation is greatly enhanced by hydrazine and boric acid while it is adversely affected by glucose. AVT chemicals acts as effective corrosion inhibitors. (author). 14 refs, 2 figs, 4 tabs

  12. Effect of EDTA with various surface active agents on the bond strength of an epoxy resin-based sealer to dentin: ex vivo

    Directory of Open Access Journals (Sweden)

    Mehmet Burak Güneşer

    2017-09-01

    Full Text Available Objective: The aim of this in vitro study was to evaluate the effect of addition of various surface-modifying agents to EDTA solution on the bond strength of an epoxy-based sealer to the root canal dentin. Materials and Method: Sixty single-rooted human mandibular premolars were decoronated and instrumented using rotary system. The specimens were then randomly divided into four groups (n=15 according to irrigation with different EDTA solution (Wizard, Rehber Kimya, Istanbul, Turkey combinations as follows: Group 1: 17% EDTA + 0.1% benzalkonium chloride; Group 2: 17% EDTA + 0.1% Tween 80; Group 3: 17% EDTA + 0.1% Triton X-100 and control group: 17% EDTA without any surface-modifying agents. Surface tensions of the EDTA solutions were controlled with a tensiometer. Final irrigation was with 5 mL of 5% sodium hypochlorite (Wizard for 1 min, followed by 5 mL of the mentioned EDTA solution for another minute. Roots were obturated with gutta-percha and AH Plus sealer (Dentsply DeTrey, Konstanz, Germany using cold lateral compaction technique. Horizontal root sections were obtained, and push-out test was used to measure the bond strength between the root canal dentin and sealer. Data were analyzed using the two-way analysis of variance and post hoc Tukey tests (p<0.05. Results: The bond strength of sealer in groups irrigated with EDTA in combination with surface modifying agents did not differ from that of the control (p=0.106. The coronal and middle third in all groups exhibited significantly greater bond strength values when compared with the apical third (p=0.004 and p=0.002, respectively. There was no statistical significant difference between the coronal and the middle thirds (p=0.979. Conclusion: The addition of surface modifying agents to EDTA solution did not affect the bond strength of the epoxy resin–based sealer.

  13. Characterization of Modified and Polymer Coated Alumina Surfaces by Infrared Spectroscopy

    Directory of Open Access Journals (Sweden)

    Ashraf Yehia El-Naggar

    2013-01-01

    Full Text Available The prepared, modified, and coated alumina surfaces were characterized by infrared spectroscopy (FTIR to investigate the surface properties of the individual and double modified samples. FTIR helps in reporting the changes occurred in hydroxyl groups as well as the structure changes as a result of thermal treating, hydrothermal treating, silylation treating, alkali metal treating, coating, and bonding with polymer. FTIR spectroscopy represents the strength and abundance of surface acidic OH which determine the adsorption properties of polar and nonpolar sorbents. Generally, all treated samples exhibit decrease of OH groups compared with those of parent ones producing alumina surfaces of different adsorptive powers.

  14. Imaging Analysis of Carbohydrate-Modified Surfaces Using ToF-SIMS and SPRi

    OpenAIRE

    Bolles, Kathryn M.; Cheng, Fang; Burk-Rafel, Jesse; Dubey, Manish; Ratner, Daniel M.

    2010-01-01

    Covalent modification of surfaces with carbohydrates (glycans) is a prerequisite for a variety of glycomics-based biomedical applications, including functional biomaterials, glycoarrays, and glycan-based biosensors. The chemistry of glycan immobilization plays an essential role in the bioavailability and function of the surface bound carbohydrate moiety. However, the scarcity of analytical methods to characterize carbohydrate-modified surfaces complicates efforts to optimize glycan surface ch...

  15. Modified expression of surface glyconjugates in stored human platelets

    International Nuclear Information System (INIS)

    Dhar, A.; Ganguly, P.

    1987-01-01

    Platelets are anucleated cells which play an important part in blood coagulation and thrombosis. These cells may be stored in the blood bank for only 4/5 days. In order to improve the storage of platelets, it is essential to first understand the changes in these cells due to storage. In this work, human platelets were stored in autologous plasma at 4 0 or 22 0 and their surface changes were monitored with three lectins - wheat germ afflutinin (WGA), concanavalin A (Con A) and lentil lectin (LL). Blood was drawn from healthy donors and platelet rich plasma (PRP) was collected by slow speed centrifugation. Platelets stored at either temperature for different times showed increased sensitivity to agglutination by WGA after 34-48 hrs. Lectins, Con A and LL, which were not agglutinating to fresh platelets readily caused agglutination after 48-72 hrs. The platelets stored for 25 hrs or longer period were insensitive to thrombin but showed enhanced aggregation with WGA. Labelling of surface glycoconjugates of stored platelets with 3 H-boro-hydride revealed progressive loss of a glycoprotein of Mr 150,000 (GPIb infinity) together with the appearance of components of Mr 69,000; Mr 60,000; Mr 25,000. New high molecular weight glycoproteins were also detected only in stored platelets. The author studies clearly indicate that modification or altered expression of platelets surface glycoproteins may be one factor of storage related dysfunction of platelets

  16. Growth of pentacene on clean and modified gold surfaces

    International Nuclear Information System (INIS)

    Kaefer, Daniel; Ruppel, Lars; Witte, Gregor

    2007-01-01

    The growth and evolution of pentacene films on gold substrates have been studied. By combining complementary techniques including scanning tunneling microscopy, atomic force microscopy, scanning electron microscopy, near-edge x-ray-absorption fine structure, and x-ray diffraction, the molecular orientation, crystalline structure, and morphology of the organic films were characterized as a function of film thickness and growth parameters (temperature and rate) for different gold substrates ranging from Au(111) single crystals to polycrystalline gold. Moreover, the influence of precoating the various gold substrates with self-assembled monolayers (SAM's) of organothiols with different chemical terminations has been studied. On bare gold the growth of pentacene films is characterized by a pronounced dewetting while the molecular orientation within the resulting crystalline three-dimensional islands depends distinctly on the roughness and cleanliness of the substrate surface. After completion of the first wetting layer where molecules adopt a planar orientation parallel to the surface the molecules continue to grow in a tilted fashion: on Au(111) the long molecular axis is oriented parallel to the surface while on polycrystalline gold it is upstanding oriented and thus parallels the crystalline orientation of pentacene films grown on SiO 2 . On SAM pretreated gold substrates the formation of a wetting layer is effectively suppressed and pentacene grows in a quasi-layer-by-layer fashion with an upstanding orientation leading to rather smooth films. The latter growth mode is observed independently of the chemical termination of the SAM's and the roughness of the gold substrate. Possible reasons for the different growth mechanism as well as consequences for the assignment of spectroscopic data of thin pentacene film are discussed

  17. Adhesion of MRC-5 and A549 cells on poly(dimethylsiloxane) surface modified by proteins.

    Science.gov (United States)

    Zuchowska, Agnieszka; Kwiatkowski, Piotr; Jastrzebska, Elzbieta; Chudy, Michal; Dybko, Artur; Brzozka, Zbigniew

    2016-02-01

    PDMS is a very popular material used for fabrication of Lab-on-a-Chip systems for biological applications. Although PDMS has numerous advantages, it is a highly hydrophobic material, which inhibits adhesion and proliferation of the cells. PDMS surface modifications are used to enrich growth of the cells. However, due to the fact that each cell type has specific adhesion, it is necessary to optimize the parameters of these modifications. In this paper, we present an investigation of normal (MRC-5) and carcinoma (A549) human lung cell adhesion and proliferation on modified PDMS surfaces. We have chosen these cell types because often they are used as models for basic cancer research. To the best of our knowledge, this is the first presentation of this type of investigation. The combination of a gas-phase processing (oxygen plasma or ultraviolet irradiation) and wet chemical methods based on proteins' adsorption was used in our experiments. Different proteins such as poly-l-lysine, fibronectin, laminin, gelatin, and collagen were incubated with the activated PDMS samples. To compare with other works, here, we also examined how ratio of prepolymer to curing agent (5:1, 10:1, and 20:1) influences PDMS hydrophilicity during further modifications. The highest adhesion of the tested cells was observed for the usage of collagen, regardless of PDMS ratio. However, the MRC-5 cell line demonstrated better adhesion than A549 cells. This is probably due to the difference in their morphology and type (normal/cancer). © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  18. Evaluation of Antibacterial Activity of Titanium Surface Modified by PVD/PACVD Process.

    Science.gov (United States)

    Ji, Min-Kyung; Lee, Min-Joo; Park, Sang-Won; Lee, Kwangmin; Yun, Kwi-Dug; Kim, Hyun-Seung; Oh, Gye-Jeong; Kim, Ji-Hyun; Lim, Hyun-Pil

    2016-02-01

    The aim of this study was to evaluate the response of Streptococcus mutans (S. mutans) via crystal violet staining assay on titanium surface modified by physical vapor deposition/plasma assisted chemical vapor deposition process. Specimens were divided into the following three groups: polished titanium (control group), titanium modified by DC magnetron sputtering (group TiN-Ti), and titanium modified by plasma nitriding (group N-Ti). Surface characteristics of specimens were observed by using nanosurface 3D optical profiler and field emission scanning electron microscope. Group TiN-Ti showed TiN layer of 1.2 microm in thickness. Group N-Ti was identified as plasma nitriding with X-ray photoelectron spectroscopy. Roughness average (Ra) of all specimens had values 0.05). Within the process condition of this study, modified titanium surfaces by DC magnetron sputtering and plasma nitriding did not influence the adhesion of S. mutans.

  19. Interfacial characterization and analytical applications of chemically-modified surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Jianhong [Iowa State Univ., Ames, IA (United States)

    1998-02-23

    The goal of this work is to explore several new strategies and approaches to the surface modification and the microscopic characterization of interfaces in the areas mainly targeting sensor technologies that are of interest to environmental control or monitoring, and scanning probe microscopies techniques that can monitor interfacial chemical reactions in real time. Centered on the main theme, four specific topics are presented as four chapters in this dissertation following the general introduction. Chapter 1 describes the development of two immobilization schemes for covalently immobilizing fluoresceinamine at cellulose acetate and its application as a pH sensing film. Chapter 2 investigates the applicability of SFM to following the base-hydrolysis of a dithio-bis(succinimidylundecanoate) monolayer at gold in situ. Chapter 3 studies the mechanism for the accelerated rate of hydrolysis of the dithio-bis(succinimidylundecanoate) monolayer at Au(111) surface. Chapter 4 focuses on the development of an electrochemical approach to the elimination of chloride interference in Chemical Oxygen Demand (COD) analysis of waste water. The procedures, results and conclusions are described in each chapter. This report contains the introduction, references, and general conclusions. Chapters have been processed separately for inclusion on the data base. 95 refs.

  20. Glass carbon surface modified by the fluorine ion irradiation

    International Nuclear Information System (INIS)

    Teranishi, Yoshikazu; Ishizuka, Masanori; Kobayashi, Tomohiro; Nakamura, Isao; Uematu, Takahiko; Yasuda, Takeshi; Mitsuo, Atsushi; Morikawa, Kazuo

    2012-01-01

    Application of nano and micro fabrication techniques in industry requires solution to some crucial problems. One of the significant problems is the sticking interface between mold surface and imprinted polymer. In this study, we report a solution to the sticking interface problem by modification of nano imprinting mold using fluorine ion implantation. After the fluorine implantation, anti sticking layer appeared on the nano imprinting mold surface. After the implantation, a mold made from glass like carbon was patterned by focused ion beam lithography. The pattern was made up of word “TIRI”. The line width was varied with 300 nm, 500 nm, and 1 μm. The line depth was about 200 ∼ 300 nm. The average depth of implanted fluorine was approximately 90 nm. After imprinting, the resin was removed from the mold by mechanical lift-off process. Transferred pattern was observed and confirmed by a scanning electron microscope (SEM) and an atomic force microscope (AFM). The pattern transferred from mold to resin was found to be successful.

  1. Modifying Thermal Transport in Colloidal Nanocrystal Solids with Surface Chemistry.

    Science.gov (United States)

    Liu, Minglu; Ma, Yuanyu; Wang, Robert Y

    2015-12-22

    We present a systematic study on the effect of surface chemistry on thermal transport in colloidal nanocrystal (NC) solids. Using PbS NCs as a model system, we vary ligand binding group (thiol, amine, and atomic halides), ligand length (ethanedithiol, butanedithiol, hexanedithiol, and octanedithiol), and NC diameter (3.3-8.2 nm). Our experiments reveal several findings: (i) The ligand choice can vary the NC solid thermal conductivity by up to a factor of 2.5. (ii) The ligand binding strength to the NC core does not significantly impact thermal conductivity. (iii) Reducing the ligand length can decrease the interparticle distance, which increases thermal conductivity. (iv) Increasing the NC diameter increases thermal conductivity. (v) The effect of surface chemistry can exceed the effect of NC diameter and becomes more pronounced as NC diameter decreases. By combining these trends, we demonstrate that the thermal conductivity of NC solids can be varied by an overall factor of 4, from ∼0.1-0.4 W/m-K. We complement these findings with effective medium approximation modeling and identify thermal transport in the ligand matrix as the rate-limiter for thermal transport. By combining these modeling results with our experimental observations, we conclude that future efforts to increase thermal conductivity in NC solids should focus on the ligand-ligand interface between neighboring NCs.

  2. Coupling of therapeutic molecules onto surface modified coralline hydroxyapatite.

    Science.gov (United States)

    Murugan, R; Ramakrishna, S

    2004-07-01

    Surface modification and coupling of therapeutic molecules, tetracycline, onto coralline hydroxyapatite (CHA) and their in vitro evaluations were described in this study. Initially, CHA was graft polymerized with glycidylmethacrylate (GMA) using redox initiators and subsequently coupled to tetracycline through epoxy groups. The CHA grafted with polyGMA (CHA-g-PGMA) was characterized by Fourier transform infrared spectroscopy and powder X-ray diffraction (XRD) for proof of grafting. The absorption peaks pertaining to epoxy and ester carbonyl groups were observed for the graft polymer due to PGMA grafting. The XRD results signified that there was no secondary phase in the apatite lattice and crystallinity was also not affected by grafting, which suggested that the PGMA chains were grafted only on the surface of CHA. Drug loading and releasing was evaluated and found that CHA-g-PGMA exhibited higher loading efficiency than CHA. The in vitro release of tetracycline was performed in phosphate buffered saline under physiological condition and the release profiles showed that the tetracycline-containing graft polymer releases the drug for prolonged period as compared to CHA. Based on the experimental results, CHA-g-PGMA appears to be a promising biomaterial for drug delivery.

  3. High Efficiency Acetylcholinesterase Immobilization on DNA Aptamer Modified Surfaces

    Directory of Open Access Journals (Sweden)

    Orada Chumphukam

    2014-04-01

    Full Text Available We report here the in vitro selection of DNA aptamers for electric eel acetylcholinesterase (AChE. One selected aptamer sequence (R15/19 has a high affinity towards the enzyme (Kd = 157 ± 42 pM. Characterization of the aptamer showed its binding is not affected by low ionic strength (~20 mM, however significant reduction in affinity occurred at high ionic strength (~1.2 M. In addition, this aptamer does not inhibit the catalytic activity of AChE that we exploit through immobilization of the DNA on a streptavidin-coated surface. Subsequent immobilization of AChE by the aptamer results in a 4-fold higher catalytic activity when compared to adsorption directly on to plastic.

  4. Effect of sealant agents on the color stability and surface roughness of nanohybrid composite resins.

    Science.gov (United States)

    Dede, Doğu Ömür; Şahin, Onur; Koroglu, Aysegül; Yilmaz, Burak

    2016-07-01

    The effect of sealant agents on the surface roughness and color stability of nanohybrid composite resins is unknown. The purpose of this in vitro study was to evaluate the effect of sealant agents on the surface roughness and color stability of 4 nanohybrid composite resin materials. Forty disks (10×2 mm) were fabricated for each nanohybrid composite resin material (Z-550, Tetric EvoCeram, Clearfill Majesty, Ice) (N=160) and divided into 4 surface treatment groups: 1 conventional polishing (control) and 3 different sealant agent (Palaseal, Optiglaze, BisCover) coupling groups (n=10). The specimens were thermocycled, and surface roughness (Ra) values were obtained with a profilometer. Scanning electron microscope images were also recorded. CIELab color parameters of each specimen were measured with a spectrophotometer before and after 7 days of storage in a coffee solution. Color differences were calculated by the CIEDE 2000 (ΔE00) formula. The data were statistically analyzed by 2-way ANOVA and by the Tukey HSD test (α=.05). The surface treatment technique significantly affected the Ra values of the composite resins tested (Pcomposite resin material was also significant for ΔE00 values (Pcomposite resin groups, significant decreases in Ra were observed only for the Palaseal agent coupled composite resin groups (except Ice) compared with the control groups (Pcomposite resin group, except for BisCover applied Clearfill Majesty (Pcomposite resin groups, significant differences were observed between the color change seen with BisCover and other sealants for Clearfill Majesty composite resin (Pcomposite resins except for Ice produced smoother surfaces. All surface sealant agents provided less discoloration of nanohybrid composite resins after coffee staining compared with conventional polishing except for BisCover applied Clearfill Majesty composite resin. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All

  5. Surface modification of magnesium hydroxide sulfate hydrate whiskers using a silane coupling agent by dry process

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Donghai, E-mail: zhudonghai-2001@163.com [Qinghai Institute of Salt Lakes, Chinese Academy of Sciences, Xining, 810008 (China); Key Laboratory of Comprehensive and Highly Efficient Utilization of Salt Lake Resources, Chinese Academy of Sciences, Xining, 810008 (China); Nai, Xueying [Qinghai Institute of Salt Lakes, Chinese Academy of Sciences, Xining, 810008 (China); Key Laboratory of Comprehensive and Highly Efficient Utilization of Salt Lake Resources, Chinese Academy of Sciences, Xining, 810008 (China); Lan, Shengjie; Bian, Shaoju [Qinghai Institute of Salt Lakes, Chinese Academy of Sciences, Xining, 810008 (China); Key Laboratory of Comprehensive and Highly Efficient Utilization of Salt Lake Resources, Chinese Academy of Sciences, Xining, 810008 (China); University of Chinese Academy of Sciences, Beijing, 100049 (China); Liu, Xin [Qinghai Institute of Salt Lakes, Chinese Academy of Sciences, Xining, 810008 (China); Key Laboratory of Comprehensive and Highly Efficient Utilization of Salt Lake Resources, Chinese Academy of Sciences, Xining, 810008 (China); Li, Wu, E-mail: driverlaoli@163.com [Qinghai Institute of Salt Lakes, Chinese Academy of Sciences, Xining, 810008 (China); Key Laboratory of Comprehensive and Highly Efficient Utilization of Salt Lake Resources, Chinese Academy of Sciences, Xining, 810008 (China)

    2016-12-30

    Highlights: • Dry process was adopted to modify the surface of MHSH whiskers using silane. • Si−O−Mg bonds were formed directly by the reaction between Si−OC{sub 2}H{sub 5} and −OH of MHSH. • Dispersibility and compatibility of modified whiskers greatly improved in organic phase. • Thermal stability of whiskers was enhanced after modified. - Abstract: In order to improve the compatibility of magnesium hydroxide sulfate hydrate (MHSH) whiskers with polymers, the surface of MHSH whiskers was modified using vinyltriethoxysilane (VTES) by dry process. The possible mechanism of the surface modification and the interfacial interactions between MHSH whiskers and VTES, as well as the effect of surface modification, were studied. Scanning electronic microscopy (SEM), transmission electron microscopy (TEM) and X-ray powder diffraction (XRD) analyses showed that the agglomerations were effectively separated and a thin layer was formed on the surface of the whiskers after modification. Fourier transform infrared (FT-IR) spectroscopy and X-ray photoelectron spectroscopy (XPS) analyses showed that the VTES molecules were bound to the surface of MHSH whiskers after modification. Chemical bonds (Si−O−Mg) were formed by the reaction between Si−OC{sub 2}H{sub 5} or Si−OH and the hydroxyl group of MHSH whiskers. The effect of surface modification was evaluated by sedimentation tests, contact angle measurements and thermogravimetric analysis (TGA). The results showed that the surface of MHSH whiskers was transformed from hydrophilic to hydrophobic, and the dispersibility and the compatibility of MHSH whiskers were significantly improved in the organic phase. Additionally, the thermal stability of the VTES-modified MHSH whiskers was improved significantly.

  6. Ligation-based mutation detection and RCA in surface un-modified OSTE+ polymer microfluidic chambers

    DEFF Research Database (Denmark)

    Saharil, Farizah; Ahlford, Annika; Kuhnemund, Malte

    2013-01-01

    For the first time, we demonstrate DNA mutation detection in surface un-modified polymeric microfluidic chambers without suffering from bubble trapping or bubble formation. Microfluidic devices were manufactured in off-stoichiometry thiol-ene epoxy (OSTE+) polymer using an uncomplicated and rapid...... during bio-operation at elevated temperatures. In contrast, PMMA, PDMS and COP microfluidic devices required specific surface treatment....

  7. Efficacy of liquid and foam decontamination technologies for chemical warfare agents on indoor surfaces.

    Science.gov (United States)

    Love, Adam H; Bailey, Christopher G; Hanna, M Leslie; Hok, Saphon; Vu, Alex K; Reutter, Dennis J; Raber, Ellen

    2011-11-30

    Bench-scale testing was used to evaluate the efficacy of four decontamination formulations on typical indoor surfaces following exposure to the liquid chemical warfare agents sarin (GB), soman (GD), sulfur mustard (HD), and VX. Residual surface contamination on coupons was periodically measured for up to 24h after applying one of four selected decontamination technologies [0.5% bleach solution with trisodium phosphate, Allen Vanguard Surface Decontamination Foam (SDF™), U.S. military Decon Green™, and Modec Inc. and EnviroFoam Technologies Sandia Decontamination Foam (DF-200)]. All decontamination technologies tested, except for the bleach solution, performed well on nonporous and nonpermeable glass and stainless-steel surfaces. However, chemical agent residual contamination typically remained on porous and permeable surfaces, especially for the more persistent agents, HD and VX. Solvent-based Decon Green™ performed better than aqueous-based bleach or foams on polymeric surfaces, possibly because the solvent is able to penetrate the polymer matrix. Bleach and foams out-performed Decon Green for penetrating the highly polar concrete surface. Results suggest that the different characteristics needed for an ideal and universal decontamination technology may be incompatible in a single formulation and a strategy for decontaminating a complex facility will require a range of technologies. Copyright © 2011 Elsevier B.V. All rights reserved.

  8. Mobile Agents: A Distributed Voice-Commanded Sensory and Robotic System for Surface EVA Assistance

    Science.gov (United States)

    Clancey, William J.; Sierhuis, Maarten; Alena, Rick; Crawford, Sekou; Dowding, John; Graham, Jeff; Kaskiris, Charis; Tyree, Kim S.; vanHoof, Ronnie

    2003-01-01

    A model-based, distributed architecture integrates diverse components in a system designed for lunar and planetary surface operations: spacesuit biosensors, cameras, GPS, and a robotic assistant. The system transmits data and assists communication between the extra-vehicular activity (EVA) astronauts, the crew in a local habitat, and a remote mission support team. Software processes ("agents"), implemented in a system called Brahms, run on multiple, mobile platforms, including the spacesuit backpacks, all-terrain vehicles, and robot. These "mobile agents" interpret and transform available data to help people and robotic systems coordinate their actions to make operations more safe and efficient. Different types of agents relate platforms to each other ("proxy agents"), devices to software ("comm agents"), and people to the system ("personal agents"). A state-of-the-art spoken dialogue interface enables people to communicate with their personal agents, supporting a speech-driven navigation and scheduling tool, field observation record, and rover command system. An important aspect of the engineering methodology involves first simulating the entire hardware and software system in Brahms, and then configuring the agents into a runtime system. Design of mobile agent functionality has been based on ethnographic observation of scientists working in Mars analog settings in the High Canadian Arctic on Devon Island and the southeast Utah desert. The Mobile Agents system is developed iteratively in the context of use, with people doing authentic work. This paper provides a brief introduction to the architecture and emphasizes the method of empirical requirements analysis, through which observation, modeling, design, and testing are integrated in simulated EVA operations.

  9. Cellular interactions of surface modified nanoporous silicon particles.

    Science.gov (United States)

    Bimbo, Luis M; Sarparanta, Mirkka; Mäkilä, Ermei; Laaksonen, Timo; Laaksonen, Päivi; Salonen, Jarno; Linder, Markus B; Hirvonen, Jouni; Airaksinen, Anu J; Santos, Hélder A

    2012-05-21

    In this study, the self-assembly of hydrophobin class II (HFBII) on the surface of thermally hydrocarbonized porous silicon (THCPSi) nanoparticles was investigated. The HFBII-coating converted the hydrophobic particles into more hydrophilic ones, improved the particles' cell viability in both HT-29 and Caco-2 cell lines compared to uncoated particles, and enhanced the particles' cellular association. The amount of HFBII adsorbed onto the particles was also successfully quantified by both the BCA assay and a HPLC method. Importantly, the permeation of a poorly water-soluble drug, indomethacin, loaded into THCPSi particles across Caco-2 monolayers was not affected by the protein coating. In addition, (125)I-radiolabelled HFBII did not extensively permeate the Caco-2 monolayer and was found to be stably adsorbed onto the THCPSi nanoparticles incubated in pH 7.4, which renders the particles the possibility for further track-imaging applications. The results highlight the potential of HFBII coating for improving wettability, increasing biocompatibility and possible intestinal association of PSi nanoparticulates for drug delivery applications.

  10. Surface modified alginate microcapsules for 3D cell culture

    Science.gov (United States)

    Chen, Yi-Wen; Kuo, Chiung Wen; Chueh, Di-Yen; Chen, Peilin

    2016-06-01

    Culture as three dimensional cell aggregates or spheroids can offer an ideal platform for tissue engineering applications and for pharmaceutical screening. Such 3D culture models, however, may suffer from the problems such as immune response and ineffective and cumbersome culture. This paper describes a simple method for producing microcapsules with alginate cores and a thin shell of poly(L-lysine)-graft-poly(ethylene glycol) (PLL-g-PEG) to encapsulate mouse induced pluripotent stem (miPS) cells, generating a non-fouling surface as an effective immunoisolation barrier. We demonstrated the trapping of the alginate microcapsules in a microwell array for the continuous observation and culture of a large number of encapsulated miPS cells in parallel. miPS cells cultured in the microcapsules survived well and proliferated to form a single cell aggregate. Droplet formation of monodisperse microcapsules with controlled size combined with flow cytometry provided an efficient way to quantitatively analyze the growth of encapsulated cells in a high-throughput manner. The simple and cost-effective coating technique employed to produce the core-shell microcapsules could be used in the emerging field of cell therapy. The microwell array would provide a convenient, user friendly and high-throughput platform for long-term cell culture and monitoring.

  11. Eco-friendly aqueous core surface-modified nanocapsules.

    Science.gov (United States)

    Carbone, C; Musumeci, T; Lauro, M R; Puglisi, G

    2015-01-01

    In this work, positively charged nanocapsules have been developed for potential ocular delivery exploiting the deposition of PLA onto the droplet surface of a W/O nanoemulsion prepared by the reversed procedure of the PIT method. PLA in combination with different amounts of various oils and surfactants have been studied in order to select the best formulation for polymeric nanocapsule preparation. The traditional visual observation together with the Turbiscan(®) technology were exploited in order to identify the best combination of polymer/oil for nanocapsule preparation. Two different primary surfactants (Span(®) 60 and Span(®) 80) have been tested to select their influence on the field of existence of the nanoemulsion by the construction of the pseudoternary phase diagrams. Cationic hybrid NC have been prepared by the addition of a coating layer of DDAB. The physico-chemical and morphological properties of all the prepared nanocapsules have been evaluated and compared by PCS, DSC and AFM. Therefore, positively charged nanocapsules can be easily prepared by a simple eco-friendly technique that exploits biocompatible materials avoiding a large input of mechanical energy as a potential ocular delivery systems for hydrophilic compounds or gene materials. Copyright © 2014 Elsevier B.V. All rights reserved.

  12. Immunoadjuvant activity of the nanoparticles’ surface modified with mannan

    Science.gov (United States)

    Haddadi, Azita; Hamdy, Samar; Ghotbi, Zahra; Samuel, John; Lavasanifar, Afsaneh

    2014-09-01

    Mannan (MN) is the natural ligand for mannose receptors, which are widely expressed on dendritic cells (DCs). The purpose of this study was to assess the effect of formulation parameters on the immunogenicity of MN-decorated poly (D, L-lactide-co-glycolide) (PLGA) nanoparticles (NPs) in terms of their ability to stimulate DC phenotypic as well as functional maturation. For this purpose, NPs were formulated from either ester-terminated or COOH-terminated PLGA. Incorporation of MN in NPs was achieved through encapsulation, physical adsorption or chemical conjugation. Murine bone marrow derived DCs (BMDCs) were treated with various NP formulations and assessed for their ability to up-regulate DC cell surface markers, secrete immunostimulatory cytokines and to activate allogenic T cell responses. DCs treated with COOH-terminated PLGA-NPs containing chemically conjugated MN (MN-Cov-COOH) have shown superior performance in improving DC biological functions, compared to the rest of the formulations tested. This may be attributed to the higher level of MN incorporation in the former formulation. Incorporation of MN in PLGA NPs through chemical conjugation can lead to enhanced DC maturation and stimulatory function. This strategy may be used to develop more effective PLGA-based vaccine formulations.

  13. Californium-252 plasma desorption mass analysis of proteins adsorbed on polymer and modified-polymer surfaces

    International Nuclear Information System (INIS)

    Hill, J.C.

    1987-01-01

    A new Cf-252 plasma desorption mass spectrometer has been built specifically for the analysis of large biomolecules. This mass spectrometer was used to investigate the interactions between proteins adsorbed onto polymer surfaces and how the chemical nature of the polymer surface influences the production of stable, gas-phase molecule ions. Chemical modification of the polymer surfaces was achieved by means of ultra-violet irradiation, resulting in the production of a more hydrophilic surface. Analysis of a series of model compounds adsorbed onto modified and non-modified polymer surfaces indicates that the wettability of the surface is an important influence in the production of stable molecular ions. This information was then utilized to aid in the analysis of lysozyme, myoglobin, and porcine trypsin

  14. A Functional Iron Oxide Nanoparticles Modified with PLA-PEG-DG as Tumor-Targeted MRI Contrast Agent.

    Science.gov (United States)

    Xiong, Fei; Hu, Ke; Yu, Haoli; Zhou, Lijun; Song, Lina; Zhang, Yu; Shan, Xiuhong; Liu, Jianping; Gu, Ning

    2017-08-01

    Tumor targeting could greatly promote the performance of magnetic nanomaterials as MRI (Magnetic Resonance Imaging) agent for tumor diagnosis. Herein, we reported a novel magnetic nanoparticle modified with PLA (poly lactic acid)-PEG (polyethylene glycol)-DG (D-glucosamine) as Tumor-targeted MRI Contrast Agent. In this work, we took use of the D-glucose passive targeting on tumor cells, combining it on PLA-PEG through amide reaction, and then wrapped the PLA-PEG-DG up to the Fe 3 O 4 @OA NPs. The stability and anti phagocytosis of Fe 3 O 4 @OA@PLA-PEG-DG was tested in vitro; the MRI efficiency and toxicity was also detected in vivo. These functional magnetic nanoparticles demonstrated good biocompatibility and stability both in vitro and in vivo. Cell experiments showed that Fe 3 O 4 @OA@PLA-PEG-DG nanoparticles exist good anti phagocytosis and high targetability. In vivo MRI images showed that the contrast effect of Fe 3 O 4 @OA@PLA-PEG-DG nanoparticles prevailed over the commercial non tumor-targeting magnetic nanomaterials MRI agent at a relatively low dose. The DG can validly enhance the tumor-targetting effect of Fe 3 O 4 @OA@PLA-PEG nanoparticle. Maybe MRI agents with DG can hold promise as tumor-targetting development in the future.

  15. High-relaxivity gadolinium-modified high-density lipoproteins as magnetic resonance imaging contrast agents

    NARCIS (Netherlands)

    Briley-Saebo, Karen C.; Geninatti-Crich, Simonetta; Cormode, David P.; Barazza, Alessandra; Mulder, Willem J. M.; Chen, Wei; Giovenzana, Giovanni B.; Fisher, Edward A.; Aime, Silvio; Fayad, Zahi A.

    2009-01-01

    There is an ongoing desire to produce high-relaxivity, Gd-based magnetic resonance imaging (MRI) contrast agents. These may allow for lower doses to be used, which is especially important in view of the current safety concerns surrounding Gd in patients. Here we report the synthesis of a

  16. Experimental gentamicin nephrotoxicity and agents that modify it: a mini-review of recent research.

    Science.gov (United States)

    Ali, Badreldin H; Al Za'abi, Mohammed; Blunden, Gerald; Nemmar, Abderrahim

    2011-10-01

    The aminoglycoside antibiotic gentamicin (GM) is still widely used against infections by Gram-positive and Gram-negative aerobic bacteria. Its therapeutic efficacy, however, is limited by renal impairment that occurs in up to 30% of treated patients. The drug may accumulate in epithelial tubular cells causing a range of effects starting with loss of the brush border in epithelial cells and ending in overt tubular necrosis, activation of apoptosis and massive proteolysis. GM also causes cell death by generation of free radicals, phospholipidosis, extracellular calcium-sensing receptor stimulation and energetic catastrophe, reduced renal blood flow and inflammation. Many drugs have been shown to either ameliorate or potentiate GM nephrotoxicity. This article aims at updating the literature that has been published in the past decade on the effects of agents that either ameliorate or augment the nephrotoxicity of this aminoglycoside. Notable among the new ameliorating procedures are gene therapy, such as intravenous cell therapy with serum amyloid A protein-programmed cells, and the use of some novel antioxidant agents and oils of natural origin. These include, for example, green tea, garlic saffron, grape seed extracts as well as sesame and oleanolic oils. Agents that may augment GM nephrotoxicity include indomethacin, cyclosporin, uric acid and the Ca(++) -channel blocker verapamil. Most of the nephroprotective agents mentioned here have not been tested in large controlled clinical trials. Because of their relative safety and effectiveness, antioxidant agents seem to be good candidates for testing in humans. © 2011 The Authors. Basic & Clinical Pharmacology & Toxicology © 2011 Nordic Pharmacological Society.

  17. Cytotoxicity of organic surface coating agents used for nanoparticles synthesis and stability.

    Science.gov (United States)

    Zhang, Ying; Newton, Brandon; Lewis, Eybriunna; Fu, Peter P; Kafoury, Ramzi; Ray, Paresh C; Yu, Hongtao

    2015-06-01

    Impact on health by nanomaterials has become a public concern with the great advances of nanomaterials for various applications. Surface coating agents are an integral part of nanoparticles, but not enough attention has been paid during toxicity tests of nanoparticles. As a result, there are inconsistent toxicity results for certain nanomaterials. In this study, we explored the cytotoxicity of eleven commonly used surface coating agents in two cell lines, human epidermal keratinocyte (HaCaT) and lung fibroblast (CRL-1490) cells, at surface coating agent concentrations of 3, 10, 30, and 100 μM. Two exposure time points, 2 h and 24 h, were employed for the study. Six of the eleven surface coating agents are cytotoxic, especially those surfactants with long aliphatic chains, both cationic (cetyltrimethylammonium bromide, oleylamine, tetraoctylammonium bromide, and hexadecylamine) and anionic (sodium dodecylsulfate). In addition, exposure time and the use of different cell lines also affect the cytotoxicity results. Therefore, factors such as cell lines used and exposure times must be considered when conducting toxicity tests or comparing cytotoxicity results. Copyright © 2015 Elsevier Ltd. All rights reserved.

  18. SUSTAINED HYPERLIPEMIA INDUCED IN RABBITS BY MEANS OF INTRAVENOUSLY INJECTED SURFACE-ACTIVE AGENTS

    Science.gov (United States)

    Kellner, Aaron; Correll, James W.; Ladd, Anthony T.

    1951-01-01

    The intravenous injection of the surface-active agents Tween 80 and Triton A20 into rabbits fed a normal diet resulted in marked and sustained elevations of the cholesterol, phospholipid, and total lipid content of their blood. The increase in phospholipid in general paralleled that of the blood cholesterol. The implications of the findings are briefly discussed. PMID:14824409

  19. Microstructure evolution and tribological properties of acrylonitrile-butadiene rubber surface modified by atmospheric plasma treatment

    Science.gov (United States)

    Shen, Ming-xue; Zhang, Zhao-xiang; Peng, Xu-dong; Lin, Xiu-zhou

    2017-09-01

    For the purpose of prolonging the service life for rubber sealing elements, the frictional behavior of acrylonitrile-butadiene rubber (NBR) surface by dielectric barrier discharge plasma treatments was investigated in this paper. Surface microstructure and chemical composition were measured by atomic force microscopy, field-emission scanning electron microscopy, and X-ray photoelectron spectroscopy, respectively. Water contact angles of the modified rubber surface were also measured to evaluate the correlation between surface wettability and tribological properties. The results show that plasma treatments can improve the properties of the NBR against friction and wear effectively, the surface microstructure and roughness of plasma-modified NBR surface had an important influence on the surface tribological behavior, and the wear depth first decreased and then increased along with the change of plasma treatment time. It was found that the wettability of the modified surface was gradually improved, which was mainly due to the change of the chemical composition after the treatment. This study suggests that the plasma treatment could effectively improve the tribological properties of the NBR surface, and also provides information for developing wear-resistant NBR for industrial applications.

  20. Freezing Damage to Isolated Tomato Fruit Mitochondria as Modified by Cryoprotective Agents and Storage Temperature 1

    Science.gov (United States)

    Dickinson, David B.; Misch, M. Joan; Drury, Robert E.

    1970-01-01

    Isolated tomato (Lycopersicon esculentum var. Kc 146) fruit mitochondria could be stored successfully in the frozen state without a cryoprotective agent if the mitochondria were frozen quickly by immersion in liquid nitrogen and later thawed quickly at 30 C. Criteria of freezing damage were rate of respiration, adenosine diphosphate to oxygen ratio, and respiratory control ratio. Marked reduction in respiration and loss of respiratory control occurred when mitochondria were transferred from liquid nitrogen to −5, −10, or −18 C for 15 minutes prior to thawing at 30 C. Dimethylsulfoxide (5%) prevented freezing damage when mitochondria were incubated at −5 C but did not prevent freezing damage at −10 or −18 C. Isolated tomato mitochondria show promise as a model system for studying the nature of freezing damage and the mode of action of cryo-protective agents. PMID:16657434

  1. Freezing damage to isolated tomato fruit mitochondria as modified by cryoprotective agents and storage temperature.

    Science.gov (United States)

    Dickinson, D B; Misch, M J; Drury, R E

    1970-08-01

    Isolated tomato (Lycopersicon esculentum var. Kc 146) fruit mitochondria could be stored successfully in the frozen state without a cryoprotective agent if the mitochondria were frozen quickly by immersion in liquid nitrogen and later thawed quickly at 30 C. Criteria of freezing damage were rate of respiration, adenosine diphosphate to oxygen ratio, and respiratory control ratio. Marked reduction in respiration and loss of respiratory control occurred when mitochondria were transferred from liquid nitrogen to -5, -10, or -18 C for 15 minutes prior to thawing at 30 C. Dimethylsulfoxide (5%) prevented freezing damage when mitochondria were incubated at -5 C but did not prevent freezing damage at -10 or -18 C. Isolated tomato mitochondria show promise as a model system for studying the nature of freezing damage and the mode of action of cryo-protective agents.

  2. Effects of surface treatment on bond strength between dental resin agent and zirconia ceramic

    International Nuclear Information System (INIS)

    Moradabadi, Ashkan; Roudsari, Sareh Esmaeily Sabet; Yekta, Bijan Eftekhari; Rahbar, Nima

    2014-01-01

    This paper presents the results of an experimental study to understand the dominant mechanism in bond strength between dental resin agent and zirconia ceramic by investigating the effects of different surface treatments. Effects of two major mechanisms of chemical and micromechanical adhesion were evaluated on bond strength of zirconia to luting agent. Specimens of yttrium-oxide-partially-stabilized zirconia blocks were fabricated. Seven groups of specimens with different surface treatment were prepared. 1) zirconia specimens after airborne particle abrasion (SZ), 2) zirconia specimens after etching (ZH), 3) zirconia specimens after airborne particle abrasion and simultaneous etching (HSZ), 4) zirconia specimens coated with a layer of a Fluorapatite-Leucite glaze (GZ), 5) GZ specimens with additional acid etching (HGZ), 6) zirconia specimens coated with a layer of salt glaze (SGZ) and 7) SGZ specimens after etching with 2% HCl (HSGZ). Composite cylinders were bonded to airborne-particle-abraded surfaces of ZirkonZahn specimens with Panavia F2 resin luting agent. Failure modes were examined under 30 × magnification and the effect of surface treatments was analyzed by scanning electron microscopy (SEM) and atomic force microscopy (AFM). SZ and HSZ groups had the highest and GZ and SGZ groups had the lowest mean shear bond strengths among all groups. Mean shear bond strengths were significantly decreased by applying a glaze layer on zirconia surfaces in GZ and SGZ groups. However, bond strengths were improved after etching process. Airborne particle abrasion resulted in higher shear bond strengths compared to etching treatment. Modes of failure varied among different groups. Finally, it is concluded that micromechanical adhesion was a more effective mechanism than chemical adhesion and airborne particle abrasion significantly increased mean shear bond strengths compared with another surface treatments. - Highlights: • Understanding the dominant mechanism of bonding

  3. Effects of surface treatment on bond strength between dental resin agent and zirconia ceramic

    Energy Technology Data Exchange (ETDEWEB)

    Moradabadi, Ashkan [Department of Electrochemistry, Universität Ulm, Ulm (Germany); Roudsari, Sareh Esmaeily Sabet [Department of Optoelectonics, Universität Ulm, Ulm (Germany); Yekta, Bijan Eftekhari [School of Materials Engineering, Iran University of Science and Technology, Tehran (Iran, Islamic Republic of); Rahbar, Nima, E-mail: nrahbar@wpi.edu [Department of Civil and Environmental Engineering, Worcester Polytechnic Institute, Worcester, MA 01609 (United States)

    2014-01-01

    This paper presents the results of an experimental study to understand the dominant mechanism in bond strength between dental resin agent and zirconia ceramic by investigating the effects of different surface treatments. Effects of two major mechanisms of chemical and micromechanical adhesion were evaluated on bond strength of zirconia to luting agent. Specimens of yttrium-oxide-partially-stabilized zirconia blocks were fabricated. Seven groups of specimens with different surface treatment were prepared. 1) zirconia specimens after airborne particle abrasion (SZ), 2) zirconia specimens after etching (ZH), 3) zirconia specimens after airborne particle abrasion and simultaneous etching (HSZ), 4) zirconia specimens coated with a layer of a Fluorapatite-Leucite glaze (GZ), 5) GZ specimens with additional acid etching (HGZ), 6) zirconia specimens coated with a layer of salt glaze (SGZ) and 7) SGZ specimens after etching with 2% HCl (HSGZ). Composite cylinders were bonded to airborne-particle-abraded surfaces of ZirkonZahn specimens with Panavia F2 resin luting agent. Failure modes were examined under 30 × magnification and the effect of surface treatments was analyzed by scanning electron microscopy (SEM) and atomic force microscopy (AFM). SZ and HSZ groups had the highest and GZ and SGZ groups had the lowest mean shear bond strengths among all groups. Mean shear bond strengths were significantly decreased by applying a glaze layer on zirconia surfaces in GZ and SGZ groups. However, bond strengths were improved after etching process. Airborne particle abrasion resulted in higher shear bond strengths compared to etching treatment. Modes of failure varied among different groups. Finally, it is concluded that micromechanical adhesion was a more effective mechanism than chemical adhesion and airborne particle abrasion significantly increased mean shear bond strengths compared with another surface treatments. - Highlights: • Understanding the dominant mechanism of bonding

  4. Reconfigurable modified surface layers using plasma capillaries around the neutral inclusion regime

    International Nuclear Information System (INIS)

    Varault, S.; Gabard, B.; Crépin, T.; Bolioli, S.; Sokoloff, J.

    2014-01-01

    We show both theoretically and experimentally reconfigurable properties achieved by plasma inclusions placed in modified surface layers generally used to tailor the transmission and beaming properties of electromagnetic bandgap based waveguiding structures. A proper parametrization of the plasma capillaries allows to reach the neutral inclusion regime, where the inclusions appear to be electromagnetically transparent, letting the surface mode characteristics unaltered. Varying the electron density of the plasma inclusions provoques small perturbations around this peculiar regime, and we observe significant modifications of the transmission/beaming properties. This offers a way to dynamically select the enhanced transmission frequency or to modify the radiation pattern of the structure, depending on whether the modified surface layer is placed at the entrance/exit of the waveguide

  5. Reconfigurable modified surface layers using plasma capillaries around the neutral inclusion regime

    Energy Technology Data Exchange (ETDEWEB)

    Varault, S. [ONERA—The French Aerospace Lab 2, Avenue Edouard Belin, BP4025, 31055 Toulouse Cedex (France); Universite Paul Sabatier—CNRS-Laplace 118, Route de Narbonne, F-31062 Toulouse Cedex 9 (France); Gabard, B. [ONERA—The French Aerospace Lab 2, Avenue Edouard Belin, BP4025, 31055 Toulouse Cedex (France); STAE—4, Rue Emile Monso, BP84234, 31030 Toulouse Cedex 4 (France); Crépin, T.; Bolioli, S. [ONERA—The French Aerospace Lab 2, Avenue Edouard Belin, BP4025, 31055 Toulouse Cedex (France); Sokoloff, J. [Universite Paul Sabatier—CNRS-Laplace 118, Route de Narbonne, F-31062 Toulouse Cedex 9 (France)

    2014-02-28

    We show both theoretically and experimentally reconfigurable properties achieved by plasma inclusions placed in modified surface layers generally used to tailor the transmission and beaming properties of electromagnetic bandgap based waveguiding structures. A proper parametrization of the plasma capillaries allows to reach the neutral inclusion regime, where the inclusions appear to be electromagnetically transparent, letting the surface mode characteristics unaltered. Varying the electron density of the plasma inclusions provoques small perturbations around this peculiar regime, and we observe significant modifications of the transmission/beaming properties. This offers a way to dynamically select the enhanced transmission frequency or to modify the radiation pattern of the structure, depending on whether the modified surface layer is placed at the entrance/exit of the waveguide.

  6. SEM Analysis of Residual Dentin Surface in Primary Teeth Using Different Chemomechanical Caries Removal Agents.

    Science.gov (United States)

    Thakur, Rachna; Patil, Sandya Devi S; Kush, Anil; Madhu, K

    The purpose of this in vitro study was to analyze the residual dentinal surfaces following caries removal using two chemomechanical methods (Papacarie Duo and Carie Care), by scanning electron microscopy (SEM). Twenty extracted primary molars with active occlusal carious lesions were randomly assigned two groups depending on the CMCR agent used for the caries excavation - Group 1 - with Papacarie Duo and Group - 2 with Carie Care. After the caries excavation, the specimens were subjected to SEM analysis. Though both the agents showed the minimal smear layer with the patent dentinal tubules, Carie care showed patent dentinal tubules with a clearly exposed peritubular and intertubular collagen network. Carie Care treated surface exhibited better surface morphology of residual dentin.

  7. Preparation and Evaluation of Some Surface Active Sequestering Agents for Some Heavy Metals

    International Nuclear Information System (INIS)

    Badawi, A.M.; Mohamed, M.Z.; Mohamed, A.S.; Khowdry, M.M.; Bastway, A.F.

    2004-01-01

    A novel series of chelating agents has been synthesized by the reaction of ethylenediaminetetraacetic acid, citric acid and polyethylene glycol with different molecular weights and different number of moles. The unique structural features of these surfactants have been confirmed by FTIR spectra, elemental analysis and H 1 NMR spectrum. These surfactants exhibit excellent properties in sequestering heavy metal such as copper, lead and mercury. They show good surfactant properties, including surface tension, effectiveness, efficiency and emulsifying power. Critical micelle concentration, maximum surface excess and minimum surface area have been studied. Free energy of micellization and adsorption have been calculated

  8. Rheological properties of grouts with viscosity modifying agents as diutan gum and welan gum incorporating pulverised fly ash

    Energy Technology Data Exchange (ETDEWEB)

    Mohammed Sonebia [Queen' s University Belfast, Belfast (United Kingdom). School of Planning, Architecture and Civil Engineering

    2006-09-15

    This investigation was undertaken to evaluate the influence of the dosage of the second generation of viscosity modifying agent (diutan gum) on fluidity and rheological parameters of cement-based materials grout compared to welan gum. All grouts were made with 0.40 water-to-binder ratio (W/B). The fresh properties of control grouts made without any viscosity modifying agent (VMA) and with superplasticizer (SP) were compared to those of grouts made with 0.02, 0.04, 0.06 and 0.08% diutan gum by mass of binder. Similar mixes made with welan gum were compared to those containing diutan gums. The effect of admixtures on fluidity and rheological parameters are discussed in this paper. The effect of the replacement of cement by pulverised fly ash (PFA) was also investigated. Grouts with replacements of PFA of 5, 13 and 20% by mass were used with the same W/B. Similar control grouts and mixes incorporated different dosages of PFA made with welan gum were made in order to compare the fluidity and the rheological parameters to the previous grouts made with diutan gum.

  9. Antithrombotic agents stimulate the synthesis and modify the sulfation pattern of a heparan sulfate proteoglycan from endothelial cells.

    Science.gov (United States)

    Pinhal, M A; Walenga, J M; Jeske, W; Hoppensteadt, D; Dietrich, C P; Fareed, J; Nader, H B

    1994-04-15

    Low molecular weight heparins, namely CY 216 and CY 222 (Sanofi/Choay); OP 622 and OP 386 (Opocrin); PK 10169 (Pharmuka); an oligosaccharide prepared from heparin by heparitinase II digestion; chemically sulfated glycosaminoglycans and polysaccharide namely Suleparoid (Syntex), Aprosulate (Luitpold-Werk); chemically modified glycosaminoglycans GAGPS and MPS (Luitpold-Werk) as well as unmodified heparin stimulate two to three fold the synthesis of a heparan sulfate with antithrombotic activity secreted by endothelial cells in culture. The stimulation is concentration dependent and specific for the endothelial cell. The [35S]-heparan sulfate synthesized in the presence of heparin and/or the tested antithrombotic agents has shown a high degree of sulfation of the iduronic acid residues as revealed by the analyses of the disaccharide products formed from the heparan sulfate by the action of bacterial heparitinases. The features of the above compounds in common with heparin are their polymeric nature and a high change density, as well as their pharmacological activities as potent antithrombotic agents "in vivo". These combined observations reinforce the proposition that the antithrombotic activity of heparin, low molecular weight heparins and the chemically modified polysaccharides could be related to the increased production of this peculiar heparan sulfate by endothelial cells.

  10. Acrylic acid surface-modified contact lens for the culture of limbal stem cells.

    Science.gov (United States)

    Zhang, Hong; Brown, Karl David; Lowe, Sue Peng; Liu, Guei-Sheung; Steele, David; Abberton, Keren; Daniell, Mark

    2014-06-01

    Surface treatment to a biomaterial surface has been shown to modify and help cell growth. Our aim was to determine the best surface-modified system for the treatment of limbal stem cell deficiency (LSCD), which would facilitate expansion of autologous limbal epithelial cells, while maintaining cultivated epithelial cells in a less differentiated state. Commercially available contact lenses (CLs) were variously surface modified by plasma polymerization with ratios of acrylic acid to octadiene tested at 100% acrylic acid, 50:50% acrylic acid:octadiene, and 100% octadiene to produce high-, mid-, and no-acid. X-ray photoelectron spectroscopy was used to analyze the chemical composition of the plasma polymer deposited layer. Limbal explants cultured on high acid-modified CLs outgrew more cells. Immunofluorescence and RT2-PCR array results indicated that a higher acrylic acid content can also help maintain progenitor cells during ex vivo expansion of epithelial cells. This study provides the first evidence for the ability of high acid-modified CLs to preserve the stemness and to be used as substrates for the culture of limbal cells in the treatment of LSCD.

  11. Electrochemical immobilization of biomolecules on gold surface modified with monolayered L-cysteine

    International Nuclear Information System (INIS)

    Honda, Mitsunori; Baba, Yuji; Sekiguchi, Tetsuhiro; Shimoyama, Iwao; Hirao, Norie

    2014-01-01

    Immobilization of organic molecules on the top of a metal surface is not easy because of lattice mismatch between organic and metal crystals. Gold atoms bind to thiol groups through strong chemical bonds, and a self-assembled monolayer of sulfur-terminated organic molecules is formed on the gold surface. Herein, we suggested that a monolayer of L-cysteine deposited on a gold surface can act as a buffer layer to immobilize biomolecules on the metal surface. We selected lactic acid as the immobilized biomolecule because it is one of the simplest carboxyl-containing biomolecules. The immobilization of lactic acid on the metal surface was carried out by an electrochemical method in an aqueous environment under the potential range varying from − 0.6 to + 0.8 V. The surface chemical states before and after the electrochemical reaction were characterized using X-ray photoelectron spectroscopy (XPS). The N 1s and C 1s XPS spectra showed that the L-cysteine-modified gold surface can immobilize lactic acid via peptide bonds. This technique might enable the immobilization of large organic molecules and biomolecules. - Highlights: • Monolayer l-cysteine deposited on Au surface as a buffer layer to immobilize biomolecules. • Lactic acid as the immobilized biomolecule as it is simple carboxyl-containing biomolecule. • X-ray photoelectron spectroscopy (XPS) of surface chemical states, before and after. • L-cysteine-modified Au surface can immobilize lactic acid via peptide bonds

  12. Surface modification of apatite-wollastonite glass ceramic by synthetic coupling agent

    Science.gov (United States)

    Long, Qin; Zhou, Da-Li; Zhang, Xiang; Zhou, Jia-Bei

    2014-06-01

    In this study, lysine was introduced into the surface of apatite—wollastonite glass ceramic (AW-GC) to improve its cytocompatibility by two steps reaction procedure. Firstly, lysine connected to N-β-(aminoethyl)-γ-aminopropyl trimethoxy silane (A-1120) by covalent binding of amide group. Secondly, the lysine-functionalized A-1120 was deposited on the surface of AW-GC through a silanization reaction involving a covalent attachment. FTIR spectra indicated that lysine had been immobilized onto the surface of AW-GC successfully. Bioactivity of the surface modified AW-GC was investigated by simulated body fluid (SBF), and the in vitro cytocompatibility was evaluated by coculturing with human osteosarcoma cell MG63. The results showed that the process of hydroxyapatite layer formed on the modified material was similar to AW-GC while the mode of hydroxyapatite deposition was changed. The growth of MG63 cells showed that modifying the AW-GC surface with lysine enhances the cell adhesion and proliferation.

  13. Enhanced osteoblast responses to poly ether ether ketone surface modified by water plasma immersion ion implantation.

    Science.gov (United States)

    Wang, Heying; Lu, Tao; Meng, Fanhao; Zhu, Hongqin; Liu, Xuanyong

    2014-05-01

    Poly ether ether ketone (PEEK) offers a set of characteristics superior for human implants; however, its application is limited by the bio-inert surface property. In this work, PEEK surface was modified using single step plasma immersion ion implantation (PIII) treatment with a gas mixture of water vapor as a plasma resource and argon as an ionization assistant. Field emission scanning electron microscopy, atomic force microscopy and X-ray photoelectron spectroscopy were used to investigate the microstructure and composition of the modified PEEK surface. The water contact angle and zeta-potential of the surfaces were also measured. Osteoblast precursor cells MC3T3-E1 and rat bone mesenchymal stem cells were cultured on the PEEK samples to evaluate their cytocompatibility. The obtained results show that the hydroxyl groups as well as a "ravined structure" are constructed on water PIII modified PEEK. Compared with pristine PEEK, the water PIII treated PEEK is more favorable for osteoblast adhesion, spreading and proliferation, besides, early osteogenic differentiation indicated by the alkaline phosphatase activity is also up-regulated. Our study illustrates enhanced osteoblast responses to the PEEK surface modified by water PIII, which gives positive information in terms of future biomedical applications. Copyright © 2014 Elsevier B.V. All rights reserved.

  14. Study on electroactive and electrocatalytic surfaces of single walled carbon nanotube-modified electrodes

    International Nuclear Information System (INIS)

    Salinas-Torres, David; Huerta, Francisco; Montilla, Francisco; Morallon, Emilia

    2011-01-01

    An investigation of the electrocatalysis of single-walled carbon nanotubes modified electrodes has been performed in this work. Nanotube-modified electrodes present a surface area much higher than the bare glassy carbon surfaces as determined by capacitance measurements. Several redox probes were selected for checking the reactivity of specific sites at the carbon nanotube surface. The presence of carbon nanotubes on the electrode improves the kinetics for all the reactions studied compared with the bare glassy carbon electrode with variations of the heterogeneous electron transfer rate constant up to 5 orders of magnitude. The most important effects are observed for the benzoquinone/hydroquinone and ferrocene/ferricinium redox couples, which show a remarkable improvement of their electron transfer kinetics on SWCNT-modified electrodes, probably due to strong π-π interaction between the organic molecules and the walls of the carbon nanotubes. For many of the reactions studied, less than 1% of the nanotube-modified electrode surface is transferring charge to species in solution. This result suggests that only nanotube tips are active sites for the electron transfer in such cases. On the contrary, the electroactive surface for the reactions of ferrocene and quinone is higher indicating that the electron transfer is produced also from the nanotube walls.

  15. Surface science and electrochemical studies of metal-modified carbides for fuel cells and hydrogen production

    Science.gov (United States)

    Kelly, Thomas Glenn

    Carbides of the early transition metals have emerged as low-cost catalysts that are active for a wide range of reactions. The surface chemistry of carbides can be altered by modifying the surface with small amounts of admetals. These metal-modified carbides can be effective replacements for Pt-based bimetallic systems, which suffer from the drawbacks of high cost and low thermal stability. In this dissertation, metal-modified carbides were studied for reactions with applications to renewable energy technologies. It is demonstrated that metal-modified carbides possess high activity for alcohol reforming and electrochemical hydrogen production. First, the surface chemistry of carbides towards alcohol decomposition is studied using density functional theory (DFT) and surface science experiments. The Vienna Ab initio Simulation Package (VASP) was used to calculate the binding energies of alcohols and decomposition intermediates on metal-modified carbides. The calculated binding energies were then correlated to reforming activity determined experimentally using temperature programmed desorption (TPD). In the case of methanol decomposition, it was found that tungsten monocarbide (WC) selectively cleaved the C-O bond to produce methane. Upon modifying the surface with a single layer of metal such as Ni, Pt, or Rh, the selectivity shifted towards scission of the C-H bonds while leaving the C-O bond intact, producing carbon monoxide (CO) and H2. High resolution energy loss spectroscopy (HREELS) was used to examine the bond breaking sequence as a function of temperature. From HREELS, it was shown that the surfaces followed an activity trend of Rh > Ni > Pt. The Au-modified WC surface possessed too low of a methanol binding energy, and molecular desorption of methanol was the most favorable pathway on this surface. Next, the ability of Rh-modified WC to break the C-C bond of C2 and C3 alcohols was demonstrated. HREELS showed that ethanol decomposed through an acetaldehyde

  16. ROMP-based thermosetting polymers from modified castor oil with various cross-linking agents

    Science.gov (United States)

    Ding, Rui

    Polymers derived from bio-renewable resources are finding an increase in global demand. In addition, polymers with distinctive functionalities are required in certain advanced fields, such as aerospace and civil engineering. In an attempt to meet both these needs, the goal of this work aims to develop a range of bio-based thermosetting matrix polymers for potential applications in multifunctional composites. Ring-opening metathesis polymerization (ROMP), which recently has been explored as a powerful method in polymer chemistry, was employed as a unique pathway to polymerize agricultural oil-based reactants. Specifically, a novel norbornyl-functionalized castor oil alcohol (NCA) was investigated to polymerize different cross-linking agents using ROMP. The effects of incorporating dicyclopentadiene (DCPD) and a norbornene-based crosslinker (CL) were systematically evaluated with respect to curing behavior and thermal mechanical properties of the polymers. Isothermal differential scanning calorimetry (DSC) was used to investigate the conversion during cure. Dynamic DSC scans at multiple heating rates revealed conversion-dependent activation energy by Ozawa-Flynn-Wall analysis. The glass transition temperature, storage modulus, and loss modulus for NCA/DCPD and NCA/CL copolymers with different cross-linking agent loading were compared using dynamic mechanical analysis. Cross-link density was examined to explain the very different dynamic mechanical behavior. Mechanical stress-strain curves were developed through tensile test, and thermal stability of the cross-linked polymers was evaluated by thermogravimetric analysis to further investigate the structure-property relationships in these systems.

  17. Surface modified Al2O3 in fluorinated polyimide/Al2O3 ...

    Indian Academy of Sciences (India)

    agglomeration. One approach to decrease the aggregation of inorganic Al2O3 is surface modification of these nanoparti- cles with coupling agent which usually has a long alkyl tail and shows a good compatibility with polymer .... ture and spatial distribution of the various components, through direct visualization. Figure 5 ...

  18. Synthesis and evaluation of some surface active agents from long chain fatty amine

    Directory of Open Access Journals (Sweden)

    Eissa, A. M. F.

    2007-12-01

    Full Text Available This study continues our series of synthesis of surface active agents containing heterocyclic moiety. NHeptadecanoyl- 3-(4-oxo-4H-benzo[d][1,3]oxazin-2-yl- acrylamide (4 was used as a new starting material to synthesize propenoxylated nonionic surface active agents having heterocycles such as (thiazole, triazole, benzoxazine, quinazoline, triazine, and oxazine. The structures of the prepared compounds were elucidated by using spectroscopic tools (IR, 1H NMR and Mass spectroscopy. Physical properties such as surface and interfacial tension, cloud point, foaming height, wetting time, emulsification power and critical micelle concentration (CMC were determined. Antimicrobial and biodegradability properties were also screened. It was found that the produced novel groups of nonionic surface active agents have pronounced surface properties and good antimicrobial activities.Este estudio continua nuestra serie sobre la síntesis de agentes surfactantes que contienen grupos heterociclicos. N-Heptadecanoyl-3-(4-oxo-4H-benzo[d][1,3]oxazin-2-yl- acrylamida (4 se usa como nueva materia prima para sintetizar surfactantes noiónico propenoxilado conteniendo herociclos tales como thiazol, triazol, benzoxazina, quinazolina, triazina, y oxazina. Las estructuras de los compuestos preparados se dilucidan mediante herramientas espectroscópicas (IR, 1H NMR and espectroscopía de masas. Se determinan sus propiedades físicas, tensión superficial e interfacial, punto de nube, altura de espuma, poder de emulsificación y concentración micelar critica.También se revisan sus propiedades antimicrobianas y de biodegradabilidad Se encontró que los nuevos compuestos poseían destacadas propiedades superficiales y unas buenas actividades antimicrobianas.

  19. Imaging Analysis of Carbohydrate-Modified Surfaces Using ToF-SIMS and SPRi

    Directory of Open Access Journals (Sweden)

    Manish Dubey

    2010-07-01

    Full Text Available Covalent modification of surfaces with carbohydrates (glycans is a prerequisite for a variety of glycomics-based biomedical applications, including functional biomaterials, glycoarrays, and glycan-based biosensors. The chemistry of glycan immobilization plays an essential role in the bioavailability and function of the surface bound carbohydrate moiety. However, the scarcity of analytical methods to characterize carbohydrate-modified surfaces complicates efforts to optimize glycan surface chemistries for specific applications. Time-of-Flight Secondary Ion Mass Spectrometry (ToF-SIMS is a surface sensitive technique suited for probing molecular composition at the biomaterial interface. Expanding ToF-SIMS analysis to interrogate carbohydrate-modified materials would increase our understanding of glycan surface chemistries and advance novel tools in the nascent field of glycomics. In this study, a printed glycan microarray surface was fabricated and subsequently characterized by ToF-SIMS imaging analysis. A multivariate technique based on principal component analysis (PCA was used to analyze the ToF-SIMS dataset and reconstruct ToF-SIMS images of functionalized surfaces. These images reveal chemical species related to the immobilized glycan, underlying glycan-reactive chemistries, gold substrates, and outside contaminants. Printed glycoarray elements (spots were also interrogated to resolve the spatial distribution and spot homogeneity of immobilized glycan. The bioavailability of the surface-bound glycan was validated using a specific carbohydrate-binding protein (lectin as characterized by Surface Plasmon Resonance Imaging (SPRi. Our results demonstrate that ToF-SIMS is capable of characterizing chemical features of carbohydrate-modified surfaces and, when complemented with SPRi, can play an enabling role in optimizing glycan microarray fabrication and performance.

  20. Imaging Analysis of Carbohydrate-Modified Surfaces Using ToF-SIMS and SPRi.

    Science.gov (United States)

    Bolles, Kathryn M; Cheng, Fang; Burk-Rafel, Jesse; Dubey, Manish; Ratner, Daniel M

    2010-07-07

    Covalent modification of surfaces with carbohydrates (glycans) is a prerequisite for a variety of glycomics-based biomedical applications, including functional biomaterials, glycoarrays, and glycan-based biosensors. The chemistry of glycan immobilization plays an essential role in the bioavailability and function of the surface bound carbohydrate moiety. However, the scarcity of analytical methods to characterize carbohydrate-modified surfaces complicates efforts to optimize glycan surface chemistries for specific applications. Time-of-Flight Secondary Ion Mass Spectrometry (ToF-SIMS) is a surface sensitive technique suited for probing molecular composition at the biomaterial interface. Expanding ToF-SIMS analysis to interrogate carbohydrate-modified materials would increase our understanding of glycan surface chemistries and advance novel tools in the nascent field of glycomics. In this study, a printed glycan microarray surface was fabricated and subsequently characterized by ToF-SIMS imaging analysis. A multivariate technique based on principal component analysis (PCA) was used to analyze the ToF-SIMS dataset and reconstruct ToF-SIMS images of functionalized surfaces. These images reveal chemical species related to the immobilized glycan, underlying glycan-reactive chemistries, gold substrates, and outside contaminants. Printed glycoarray elements (spots) were also interrogated to resolve the spatial distribution and spot homogeneity of immobilized glycan. The bioavailability of the surface-bound glycan was validated using a specific carbohydrate-binding protein (lectin) as characterized by Surface Plasmon Resonance Imaging (SPRi). Our results demonstrate that ToF-SIMS is capable of characterizing chemical features of carbohydrate-modified surfaces and, when complemented with SPRi, can play an enabling role in optimizing glycan microarray fabrication and performance.

  1. Application of a modified electrochemical system for surface decontamination of radioactive metal waste

    International Nuclear Information System (INIS)

    Lee, J.H.; Lim, Y.K.; Yang, H.Y.; Shin, S.W.; Song, M.J.

    2003-01-01

    Conventional and modified electrolytic decontamination experiments were performed in a solution of sodium sulfate for the decontamination of carbon steel as the simulated metal wastes which are generated in large amounts from nuclear power plants. The effect of reaction time, current density and concentration of electrolytes in the modified electrolytic decontamination system were examined to remove the surface contamination of the simulated radioactive metal wastes. As for the results of this research, the modified electrochemical decontamination process can decontaminate more effectively than the conventional decontamination process by applying different anode material which causes higher induced electro-motive forces. When 0.5 M sodium sulfate, 0.4 A/cm 2 current density and 30 minutes reaction time were applied in the modified process, a 16 μm thickness change that is expected to remove most surface contamination in radioactive metal wastes was achieved on carbon steel which is the main material of radioactive metal waste in nuclear power plants. The decontamination efficiency of metal waste showed similar results with the small and large lab-scale modified electrochemical system. The application of this modified electrolytic decontamination system is expected to play a considerable role for decontamination of radioactive metal waste in nuclear power plants in the near future. (author)

  2. Carbon Textiles Modified with Copper-Based Reactive Adsorbents as Efficient Media for Detoxification of Chemical Warfare Agents.

    Science.gov (United States)

    Florent, Marc; Giannakoudakis, Dimitrios A; Wallace, Rajiv; Bandosz, Teresa J

    2017-08-16

    Carbon textile swatch was oxidized and impregnated with copper hydroxynitrate. A subsample was then further heated at 280 °C to form copper oxide. The swatches preserved their integrity through the treatments. As final products, they exhibited remarkable detoxification properties for the nerve agent surrogate dimethyl chlorophosphate (DMCP). Based on the amount of reactive copper phases deposited on the fibers, their adsorption capacities were higher than those of the bulk powders. After 1 day exposure to DMCP (1:1 weight ratio adsorbent/DMCP), 99% of the initial amount of DMCP was eliminated. A synergistic effect of the composite components was clearly seen. GC-MS results showed that the main surface reaction product was chloromethane. Its formation indicated hydrolysis as a detoxification path. Surface analyses showed phosphate bonding to the fibers and formation of copper chloride. The appearance of the latter species results in a clear textile color change, which suggests the application of these fabrics not only as catalytic protection agents but also as sensors of nerve agents.

  3. Modifying the photodetachment near a metal surface by a weak electric field

    OpenAIRE

    Yang, B. C.; Du, M. L.

    2009-01-01

    We show the photodetachment cross sections of H near a metal surface can be modified using a weak static electric field. The modification is possible because the oscillatory part of the cross section near a metal surface is directly connected with the transit-time and the action of the detached-electron closed-orbit which can be changed systematically by varying the static electric field strength. Photodetachment cross sections for various photon energies and electric field values are calcula...

  4. Surface Modification, Characterization and Photocatalytic Performance of Nano-Sized Titania Modified with Silver and Bentonite Clay

    Directory of Open Access Journals (Sweden)

    Neetu Divya

    2009-12-01

    Full Text Available In many textile industries dyes are used as coloring agents. Advanced oxidation processes are used for degrading or removing color from dye baths. Catalysts play a key role in these industries for the treatment of water. Solid catalysts are usually composed of metals that form supports onto the surface and create metal particles with high surface areas. TiO2 composites containing transition metal ions (silver and/or bentonite clay were prepared. Photocatalytic efficiencies have been investigated for the degradation of Orange G an azo dye. Various analytical techniques were used to characterize the surface properties of nano-sized titania modified using silver and/or bentonite clay. Scanning electron microscopy (SEM, Transmission electron microscopy (TEM, X-ray diffraction (XRD and FTIR analyses showed that TiO2 (10 ± 2 nm and Ag (2 to 3 nm particles were supported on the surface of the bentonite clay and the size was in the range of 100 ± 2 nm. The modified catalysts P-25 TiO2/Bentonite/Ag and P-25 TiO2/Ag were found to be very active for the photocatalytic decomposition of Orange G. The percent decolorization in 60 min was 98% with both P-25 TiO2/Ag and P-25 TiO2/Bentonite/Ag modified catalysts. Whereas mineralization achieved in 9 hr were 68% and 71% with P-25 TiO2/Bentonite/Ag and P-25 TiO2/Ag catalyst respectively. © 2009 BCREC UNDIP. All rights reserved[Received: 30 October 2009, Revised: 20 November 2009, Accepted: 21 November 2009][How to Cite: N. Divya, A. Bansal, A. K. Jana. (2009. Surface Modification, Characterization and Photocatalytic Performance of Nano-Sized Titania Modified with Silver and Bentonite Clay. Bulletin of Chemical Reaction Engineering and Catalysis, 4(2: 43-53.  doi:10.9767/bcrec.4.2.1249.43-53][How to Link/ DOI: http://dx.doi.org/10.9767/bcrec.4.2.1249.43-53 || or local: http://ejournal.undip.ac.id/index.php/bcrec/article/view/1249

  5. [Modified polyurethane foam as a local hemostatic agent after dental extractions].

    Science.gov (United States)

    Selten, M H A; Broekema, F I; Zuidema, J; van Oeveren, W; Bos, R R M

    2013-01-01

    In this split mouth experiment, the feasibility ofpolyurethane foam as a local hemostatic agent after dental extractions was studied. Ten healthy patients underwent 2 extractions ofa dental element in 1 treatment session. The 10 patients were subsequently randomly divided in a gelatin group and a collagen group. In the gelatin group, a polyurethane foam (PU) was applied in 1 extraction socket, while in the other socket a commercially available gelatin foam was applied. In the collagen group, a PU was applied in 1 socket, and a collagen wadding in the other. All hemostats were removed after 2 minutes, after which the degree of coagulation was measured using a thrombin/antithrombin test and a fibrinogen test. This study suggests that polyurethane foam has hemostatic capacity. Large scale clinical research is needed to confirm this finding, and should indicate whether this hemostatic capacity is clinically relevant.

  6. Optimization of Phospholipase A1 Immobilization on Plasma Surface Modified Chitosan Nanofibrous Mat

    Directory of Open Access Journals (Sweden)

    Zahra Beig Mohammadi

    2016-01-01

    Full Text Available Phospholipase A1 is known as an effective catalyst for hydrolysis of various phospholipids in enzymatic vegetable oil degumming. Immobilization is one of the most efficient strategies to improve its activity, recovery and functional properties. In this study, chitosan-co-polyethylene oxide (90:10 nanofibrous mat was successfully fabricated and modified with atmospheric plasma at different times (2, 6 and 10 min to interact with enzyme molecules. Scanning electron microscopy images revealed that the membranes retained uniform nanofibrous and open porous structures before and after the treatment. PLA1 was successfully immobilized onto the membrane surfaces via covalent bonds with the functional groups of chitosan nanofibrous mat. Response surface methodology was used to optimize the immobilization conditions for reaching the maximum immobilization efficiency. Enzyme concentration, pH, and immobilization time were found to be significant key factors. Under optimum conditions (5.03 h, pH 5.63, and enzyme dosage 654.36 UI, the atmospheric plasma surface modified chitosan nanofibers reached the highest immobilization efficiency (78.50%. Fourier transform infrared spectroscopy of the control and plasma surface-modified chitosan nanofibers revealed the functional groups of nanofibers and their reaction with the enzyme. The results indicated that surface modification by atmospheric plasma induced an increase in PLA1 loading on the membrane surfaces.

  7. Surface modified Al2O3 in fluorinated polyimide/Al2O3 ...

    Indian Academy of Sciences (India)

    the mechanical and thermal properties of polymers (Li et al. 2010). Herein, we wish to report the synthesis and characte- rization of fluorinated PI–Al2O3 nanocomposite films via in situ polymerization using different contents of surface modified Al2O3 nanoparticles as filler and fluorinated PI as the matrix. PI which was used ...

  8. Microgel-based surface modifying system for stimuli-responsive functional finishing of cotton

    NARCIS (Netherlands)

    Kulkarni, A.N.; Tourrette, A.; Warmoeskerken, Marinus; Jocic, D.

    2010-01-01

    An innovative strategy for functional finishing of textile materials is based on the incorporation of a thin layer of surface modifying systems (SMS) in the form of stimuli-sensitive microgels or hydrogels. Since the copolymerization of poly(N-isopropylacrylamide) with an ionizable polymer, such as

  9. Systematic screening of different surface modifiers for the production of physically stable nanosuspensions.

    Science.gov (United States)

    Lestari, Maria L A D; Müller, Rainer H; Möschwitzer, Jan P

    2015-03-01

    The role of a surface modifier is important in the formation of stable nanosuspensions. In this study, a simple and systematic screening method for selecting optimum surface modifiers was performed by utilizing a low-energy wet ball milling method. Nine surface modifiers from different classes with different stabilization mechanisms were applied on six different models of active pharmaceutical ingredients (API). Particle size analysis showed that at concentration five times higher than the critical micelle concentration, SDS and sodium cholate (anionic surfactant) showed the highest percent success to produce stable nanosuspensions with particle size smaller than 250 nm. Similar findings were also shown by poloxamer 188 (nonionic surfactant) and hydroxypropylmethylcellulose E5 (polymeric stabilizer) at concentration 1% (w/v) and 0.8% (w/v), respectively. In addition, combinations of anionic surfactant and nonionic surfactant as well as combinations of anionic surfactant and polymeric stabilizer showed high percent success in the formation of stable nanosuspensions. In general, no correlation can be found between the physicochemical characteristics of the model API (molecular weight, melting point, log P, pKa, and crystallinity) with its feasibility to be nanosized. The concentration and the principle of stabilization of surface modifier determine the formation of stable nanosuspensions. © 2015 Wiley Periodicals, Inc. and the American Pharmacists Association.

  10. Surface characterization of weathered wood-plastic composites produced from modified wood flour

    Science.gov (United States)

    James S. Fabiyi; Armando G. McDonald; Nicole M. Stark

    2007-01-01

    The effects of weathering on the surface properties of wood-plastic composites (WPC) were examined. High-density polyethylene (HDPE) based WPCs made from modified wood flour (untreated, extractives free, and holocellulose (delignified) fibers) were subjected to accelerated (xenon-arc) weathering. Colorimetry and Fourier-transform infrared spectroscopy were employed to...

  11. THE PATHOGENESIS OF HYPERLIPEMIA INDUCED BY MEANS OF SURFACE-ACTIVE AGENTS

    Science.gov (United States)

    Hirsch, Robert L.; Kellner, Aaron

    1956-01-01

    Rabbits subjected to subtotal hepatectomy failed to develop increased serum cholesterol levels following parenteral injection of triton WR 1339, the finding indicating that the liver is essential for the establishment of the hypercholesterolemia induced by surface-active agents. The cholesterol content of the livers of rabbits rendered hyperlipemic by means of triton remained unchanged both during the rapid rise of the serum cholesterol levels and during the return to normal values. By contrast, the cholesterol content of the livers of rabbits fed cholesterol rose progressively over a period of 5 weeks, concommittant with the increase in serum cholesterol levels. The findings provide support for the hypothesis that surface-active agents bring about hyperlipemia by altering the circulating lipoproteins in some manner so that they are retained in the circulating body fluids. PMID:13332177

  12. Interfacial effects of surface-active agents under zinc pressure leach conditions

    Science.gov (United States)

    Owusu, George; Dreisinger, David B.; Peters, Ernest

    1995-02-01

    Liquid sulfur-zinc sulfate solution interfacial tensions and liquid sulfur-zinc sulfate solution-zinc sulfide (marmatite) contact angles were measured in the absence and presence of surface-active agents. Interfacial tensions measured varied between 54 ± 1 mN/m in the surfactant-free system and 20 ± 1 mN/m in the presence of a surfactant. The liquid sulfur-zinc sulfide mineral-zinc sulfate solution contact angle varies between 80 ± 5 deg, in the absence of any surfactant, and 148 ± 5 deg, depending on the surfactant used. The surface-active agents were used as dispersants for sulfur in bench-scale zinc pressure-leaching experiments. The observed extent of zinc extraction depends on the surfactant and varies from 40 to 96 pct.

  13. In situ surface-enhanced raman spectroelectrochemical analysis system with a hemin modified nanostructured gold surface

    NARCIS (Netherlands)

    Yuan, Tao; Le Thi Ngoc, Loan; van Nieuwkasteele, Jan William; Odijk, Mathieu; van den Berg, Albert; Permentier, Hjalmar; Bischoff, Rainer; Carlen, Edwin

    2015-01-01

    An integrated surface-enhanced Raman scattering (SERS) spectroelectrochemical (SEC) analysis system is presented that combines a small volume microfluidic sample chamber (<100 mu L) with a compact three-electrode configuration for in situ surface-enhanced Raman spectroelectrochemistry. The SEC

  14. In situ surface-enhanced Raman spectroelectrochemical analysis system with a hemin modified nanostructured gold surface

    NARCIS (Netherlands)

    Yuan, Tao; Le Thi Ngoc, Loan; van Nieuwkasteele, Jan; Odijk, Mathieu; van den Berg, Albert; Permentier, Hjalmar; Bischoff, Rainer; Carlen, Edwin T

    2015-01-01

    An integrated surface-enhanced Raman scattering (SERS) spectroelectrochemical (SEC) analysis system is presented that combines a small volume microfluidic sample chamber (<100 μL) with a compact three-electrode configuration for in situ surface-enhanced Raman spectroelectrochemistry. The SEC system

  15. Effects of surface treatment on bond strength between dental resin agent and zirconia ceramic.

    Science.gov (United States)

    Moradabadi, Ashkan; Roudsari, Sareh Esmaeily Sabet; Yekta, Bijan Eftekhari; Rahbar, Nima

    2014-01-01

    This paper presents the results of an experimental study to understand the dominant mechanism in bond strength between dental resin agent and zirconia ceramic by investigating the effects of different surface treatments. Effects of two major mechanisms of chemical and micromechanical adhesion were evaluated on bond strength of zirconia to luting agent. Specimens of yttrium-oxide-partially-stabilized zirconia blocks were fabricated. Seven groups of specimens with different surface treatment were prepared. 1) zirconia specimens after airborne particle abrasion (SZ), 2) zirconia specimens after etching (ZH), 3) zirconia specimens after airborne particle abrasion and simultaneous etching (HSZ), 4) zirconia specimens coated with a layer of a Fluorapatite-Leucite glaze (GZ), 5) GZ specimens with additional acid etching (HGZ), 6) zirconia specimens coated with a layer of salt glaze (SGZ) and 7) SGZ specimens after etching with 2% HCl (HSGZ). Composite cylinders were bonded to airborne-particle-abraded surfaces of ZirkonZahn specimens with Panavia F2 resin luting agent. Failure modes were examined under 30× magnification and the effect of surface treatments was analyzed by scanning electron microscopy (SEM) and atomic force microscopy (AFM). SZ and HSZ groups had the highest and GZ and SGZ groups had the lowest mean shear bond strengths among all groups. Mean shear bond strengths were significantly decreased by applying a glaze layer on zirconia surfaces in GZ and SGZ groups. However, bond strengths were improved after etching process. Airborne particle abrasion resulted in higher shear bond strengths compared to etching treatment. Modes of failure varied among different groups. Finally, it is concluded that micromechanical adhesion was a more effective mechanism than chemical adhesion and airborne particle abrasion significantly increased mean shear bond strengths compared with another surface treatments. © 2013.

  16. NATURAL ANTIBIOFOULING AGENTS AS NEW CONTROL METHOD FOR PHOTOTROPHIC BIOFILMS DWELLING ON MONUMENTAL STONE SURFACES

    OpenAIRE

    Oana-Adriana CUZMAN; Mara CAMAITI; Barbara SACCHI; Piero TIANO

    2011-01-01

    Five natural antibiofoulants with terrestrial (capsaicine - CS, cinnamaldehyde - CI) and marine origin (zosteric acid - ZA, poly-alkylpyridinium salts - pAPS and Ceramium botryocarpum extract - CBE) have been selected and tested against phototrophic biofilm formation on the stone surfaces for their inhibitory properties. The antibiofouling agents (ABAs) were incorporated into two commercial silicone based coatings (Silres BS OH 100 - S and Silres BS 290 - W). In this work, phototrophic growth...

  17. Effect of surface treatments on the flexural properties and adhesion of glass fiber-reinforced composite post to self-adhesive luting agent and radicular dentin.

    Science.gov (United States)

    Elnaghy, Amr M; Elsaka, Shaymaa E

    2016-01-01

    This study evaluated the effect of different surface treatments on the flexural properties and adhesion of glass fiber post to self-adhesive luting agent and radicular dentin. Seventy-five single-rooted human teeth were prepared to receive a glass fiber post (Reblida). The posts were divided into five groups according to the surface treatment: Gr C (control; no treatment), Gr S (silanization for 60 s), Gr AP (airborne-particle abrasion), Gr HF (etching with 9 % hydrofluoric acid for 1 min), and Gr M10 (etching with CH2Cl2 for 10 min). Dual-cure self-adhesive luting agent (Rely X Unicem) was applied to each group for testing the adhesion using micropush-out test. Failure types were examined with stereomicroscope and surface morphology of the posts was characterized using a scanning electron microscopy (SEM). Flexural properties of posts were assessed using a three-point bending test. Data were analyzed using ANOVA and Tukey's HSD test. Statistical significance was set at the 0.05 probability level. Groups treated with M10 showed significantly higher bond strength than those obtained with other surface treatments (P C > S > AP > HF. Most failure modes were adhesive type of failures between dentin and luting agent (48.2%). SEM analysis revealed that the fiber post surfaces were modified after surface treatments. The surface treatments did not compromise the flexural properties of fiber posts. Application of M10 to the fiber post surfaces enhanced the adhesion to self-adhesive luting agent and radicular dentin.

  18. Response surface modeling of boron adsorption from aqueous solution by vermiculite using different adsorption agents: Box-Behnken experimental design.

    Science.gov (United States)

    Demirçivi, Pelin; Saygılı, Gülhayat Nasün

    2017-07-01

    In this study, a different method was applied for boron removal by using vermiculite as the adsorbent. Vermiculite, which was used in the experiments, was not modified with adsorption agents before boron adsorption using a separate process. Hexadecyltrimethylammonium bromide (HDTMA) and Gallic acid (GA) were used as adsorption agents for vermiculite by maintaining the solid/liquid ratio at 12.5 g/L. HDTMA/GA concentration, contact time, pH, initial boron concentration, inert electrolyte and temperature effects on boron adsorption were analyzed. A three-factor, three-level Box-Behnken design model combined with response surface method (RSM) was employed to examine and optimize process variables for boron adsorption from aqueous solution by vermiculite using HDTMA and GA. Solution pH (2-12), temperature (25-60 °C) and initial boron concentration (50-8,000 mg/L) were chosen as independent variables and coded x 1 , x 2 and x 3 at three levels (-1, 0 and 1). Analysis of variance was used to test the significance of variables and their interactions with 95% confidence limit (α = 0.05). According to the regression coefficients, a second-order empirical equation was evaluated between the adsorption capacity (q i ) and the coded variables tested (x i ). Optimum values of the variables were also evaluated for maximum boron adsorption by vermiculite-HDTMA (HDTMA-Verm) and vermiculite-GA (GA-Verm).

  19. Response to antiseptic agents of periodontal pathogens in in vitro biofilms on titanium and zirconium surfaces.

    Science.gov (United States)

    Sánchez, M C; Fernández, E; Llama-Palacios, A; Figuero, E; Herrera, D; Sanz, M

    2017-04-01

    The aim of this study was to develop in vitro biofilms on SLA titanium (Ti-SLA) and zirconium oxide (ZrO 2 ) surfaces and to evaluate the effect of antiseptic agents on the number of putative periodontal pathogenic species. An in vitro biofilm model was developed on sterile discs of Ti-SLA and ZrO 2 . Three antiseptic agents [chlorhexidine and cetyl-pyridinium-chloride (CHX/CPC), essential oils (EEOOs) and cetyl-peridinium-chloride (CPC)] were applied to 72-h biofilms, immersing discs during 1min in the antiseptic solution, either with or without mechanical disruption. Viable bacteria [colony forming units (CFU/mL)] were measured by quantitative polymerase chain reaction (qPCR) combined with propidium monoazide. A generalized lineal model was constructed to determine the effect of the agents on the viable bacterial counts of Aggregatibacter actinomycetemcomitans, Porphyromonas gingivalis and Fusobacterium nucleatum on each surface. The exposure to each antiseptic solution resulted in a statistically significant reductions in the number of viable target species included in the in vitro multi-species biofilm, on both Ti-SLA and ZrO 2 (pantiseptics when grown in multispecies biofilms on titanium and zirconium surfaces, in spite of the described structural differences between these bacterial communities. Copyright © 2017 The Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  20. Processing method and processing device for liquid waste containing surface active agent and radioactive material

    International Nuclear Information System (INIS)

    Nishi, Takashi; Matsuda, Masami; Baba, Tsutomu; Yoshikawa, Ryozo; Yukita, Atsushi.

    1998-01-01

    Washing liquid wastes containing surface active agents and radioactive materials are sent to a deaerating vessel. Ozone is blown into the deaerating vessel. The washing liquid wastes dissolved with ozone are introduced to a UV ray irradiation vessel. UV rays are irradiated to the washing liquid wastes, and hydroxy radicals generated by photodecomposition of dissolved ozone oxidatively decompose surface active agents contained in the washing liquid wastes. The washing liquid wastes discharged from the UV ray irradiation vessel are sent to an activated carbon mixing vessel and mixed with powdery activated carbon. The surface active agents not decomposed in the UV ray irradiation vessel are adsorbed to the activated carbon. Then, the activated carbon and washing liquid wastes are separated by an activated carbon separating/drying device. Radioactive materials (iron oxide and the like) contained in the washing liquid wastes are mostly granular, and they are separated and removed from the washing liquid wastes in the activated carbon separating/drying device. (I.N.)

  1. Boiling performance and material robustness of modified surfaces with multi scale structures for fuel cladding development

    International Nuclear Information System (INIS)

    Jo, HangJin; Kim, Jin Man; Yeom, Hwasung; Lee, Gi Cheol; Park, Hyun Sun; Kiyofumi, Moriyama; Kim, Moo Hwan; Sridharan, Kumar; Corradini, Michael

    2015-01-01

    Highlights: • We improved boiling performance and material robustness using surface modification. • We combined micro/millimeter post structures and nanoparticles with heat treatments. • Compactly-arranged micrometer posts had improved boiling performance. • CHF increased significantly due to capillary pumping by the deposited NP layers. • Sintering procedure increased mechanical strength of the NP coating surface. - Abstract: By regulating the geometrical characteristics of multi-scale structures and by adopting heat treatment for protective layer of nanoparticles (NPs), we improved critical heat flux (CHF), boiling heat transfer (BHT), and mechanical robustness of the modified surface. We fabricated 1-mm and 100-μm post structures and deposited NPs on the structured surface as a nano-scale structured layer and protective layer at the same time, then evaluated the CHF and BHT and material robustness of the modified surfaces. On the structured surfaces without NPs, the surface with compactly-arranged micrometer posts had improved CHF (118%) and BHT (41%). On the surface with structures on which NPs had been deposited, CHF increased significantly (172%) due to capillary pumping by the deposited NP layers. The heat treatment improved robustness of coating layer in comparison to the one of before heat treatment. In particular, low-temperature sintering increased the hardness of the modified surface by 140%. The increased mechanical strength of the NP coating is attributed to reduction in coating porosity during sintering. The combination of micrometer posts structures and sintered NP coating can increase the safety, efficiency and reliability of advanced nuclear fuel cladding

  2. Cd(II) removal on surface-modified activated carbon: equilibrium, kinetics and mechanism.

    Science.gov (United States)

    Liang, Jianjun; Liu, Meiling; Zhang, Yufei

    2016-10-01

    Commercial pulverous activated carbon (AC-0) was modified through two steps: oxidize AC-0 acid firstly, impregnate it with iron using ferric chloride secondly. Orthogonal experiment was conducted then to prepare modified activated carbon with high Cd(II) adsorption capacity (ACNF). Batch adsorption experiments were undertaken to determine the adsorption characteristics of Cd(II) from aqueous solution onto AC-0 and ACNF and the effect of pH, contact time and initial Cd(II) concentration. The results indicate that: the adsorption behavior of Cd(II) on ACNF can be well fitted with Langmuir model, and the maximum adsorption capacity of ACNF was 2.3 times higher than that of AC-0, supporting a monolayer coverage of Cd(II) on the surface. The kinetics of the adsorption process can be described by pseudo-second-order rate equation very well, and the adsorption capacity increased from 0.810 mg/g to 0.960 mg/g after modification. Compared with AC-0, the kinetic parameters of ACNF showed a higher adsorption rate through the aqueous solution to the solid surface and a lower intraparticle diffusion rate. Surface modification resulted in a lower Brunauer-Emmett-Teller (BET) surface area and pore size because of the collapse and blockage of pores, according to the X-ray diffraction (XRD) analysis, while the total number of surface oxygen acid groups increased, and this was supposed to contribute to the enhanced adsorption capacity of modified activated carbon.

  3. Recent Progress on C-4-Modified Podophyllotoxin Analogs as Potent Antitumor Agents

    Science.gov (United States)

    Liu, Ying-Qian; Tian, Jing; Qian, Keduo; Zhao, Xiao-Bo; Morris-Natschke, Susan L.; Yang, Liu; Nan, Xiang; Tian, Xuan; Lee, Kuo-Hsiung

    2015-01-01

    Podophyllotoxin (PPT), as well as its congeners and derivatives, exhibits pronounced biological activities, especially antineoplastic effects. Its strong inhibitory effect on tumor cell growth led to the development of three of the most highly prescribed anticancer drugs in the world, etoposide, teniposide, and the water-soluble prodrug etoposide phosphate. Their clinical success as well as intriguing mechanism of action stimulated great interest in further modification of PPT for better antitumor activity. The C-4 position has been a major target for structural derivatization aimed at either producing more potent compounds or overcoming drug resistance. Accordingly, numerous PPT derivatives have been prepared via hemisynthesis and important structure–activity relationship (SAR) correlations have been identified. Several resulting compounds, including GL-331, TOP-53, and NK611, reached clinical trials. Some excellent reviews on the distribution, sources, applications, synthesis, and SAR of PPT have been published. This review focuses on a second generation of new etoposide-related drugs and provides detailed coverage of the current status and recent development of C-4-modified PPT analogs as anticancer clinical trial candidates. PMID:24827545

  4. Acute Effects of Vascular Modifying Agents in Solid Tumors Assessed by Noninvasive Laser Doppler Flowmetry and Near Infrared Spectroscopy

    Directory of Open Access Journals (Sweden)

    Michael Kragh

    2002-01-01

    Full Text Available The potential of noninvasive laser Doppler flowmetry (LDF and near infrared spectroscopy (NIRS to detect acute effects of different vascular-modifying agents on perfusion and blood volume in tumors was evaluated. C3H mouse mammary carcinomas (∼200 mm3 in the rear foot of CDF1 mice were treated with flavone acetic acid (FAA, 150 mg/kg, 5,6-dimethylxanthenone-4acetic acid (DMXAA, 20 mg/kg, combretastatin A-4 disodium phosphate (CAMP, 250 mg/kg, hydralazine (HDZ, 5 mg/kg, or nicotinamide (NTA, 500 mg/kg. Tumor perfusion before and after treatment was evaluated by noninvasive LDF, using a 41°C heated custombuilt LDF probe with four integrated laser/receiver units, and tumor blood volume was estimated by MRS, using light guide coupled reflectance measurements at 800±10 nm. FAA, DMXAA, CAMP, and HDZ significantly decreased tumor perfusion by 50%, 47%, 73%, and 78%, respectively. In addition, FAA, DMXAA, and HDZ significantly reduced the blood volume within the tumor, indicating that these compounds to some degree shunted blood from the tumor to adjacent tissue, HDZ being most potent. CAMP caused no change in the tumor blood volume, indicating that the mechanism of action of CAMP was vascular shut down with the blood pool trapped in the tumor. NTA caused no change in either tumor perfusion or tumor blood volume. We conclude that noninvasive LDF and MRS can determine acute effects of vascular modifying agents on tumor perfusion and blood volume.

  5. Mesquite Gum as a Novel Reducing and Stabilizing Agent for Modified Tollens Synthesis of Highly Concentrated Ag Nanoparticles

    Directory of Open Access Journals (Sweden)

    Maira Berenice Moreno‐Trejo

    2016-10-01

    Full Text Available The synthesis that is described in this study is for the preparation of silver nanoparticles of sizes ranging from 10 nm to 30 nm with a defined shape (globular, confirmed by UV-vis, SEM, STEM and DLS analysis. This simple and favorable one-step modified Tollens reaction does not require any special equipment or other stabilizing or reducing agent except for a solution of purified mesquite gum, and it produces aqueous colloidal dispersions of silver nanoparticles with a stability thatexceeds three months, a relatively narrow size distribution, a low tendency to aggregate and a yield of at least 95% for all cases. Reaction times are between 15 min and 60 min to obtain silver nanoparticles in concentrations ranging from 0.1 g to 3 g of Ag per 100 g of reaction mixture. The proposed synthetic method presents a high potential for scale-up, since its production capacity is rather high and the methodology is simple.The synthesis that is described in this study is for the preparation of silver nanoparticles of sizes ranging from 10 nm to 30 nm with a defined shape (globular, confirmed by UV-vis, SEM, STEM and DLS analysis. This simple and favorable one-step modified Tollens reaction does not require any special equipment or other stabilizing or reducing agent except for a solution of purified mesquite gum, and it produces aqueous colloidal dispersions of silver nanoparticles with a stability thatexceeds three months, a relatively narrow size distribution, a low tendency to aggregate and a yield of at least 95% for all cases. Reaction times are between 15 min and 60 min to obtain silver nanoparticles in concentrations ranging from 0.1 g to 3 g of Ag per 100 g of reaction mixture. The proposed synthetic method presents a high potential for scale-up, since its production capacity is rather high and the methodology is simple.

  6. The Control of Mesenchymal Stromal Cell Osteogenic Differentiation through Modified Surfaces

    Directory of Open Access Journals (Sweden)

    Niall Logan

    2013-01-01

    Full Text Available Stem cells continue to receive widespread attention due to their potential to revolutionise treatments in the fields of both tissue engineering and regenerative medicine. Adult stem cells, specifically mesenchymal stromal cells (MSCs, play a vital role in the natural events surrounding bone healing and osseointegration through being stimulated to differentiate along their osteogenic lineage and in doing so, they form new cortical and trabecular bone tissue. Understanding how to control, manipulate, and enhance the intrinsic healing events modulated through osteogenic differentiation of MSCs by the use of modified surfaces and biomaterials could potentially advance the fields of both orthopaedics and dentistry. This could be by either using surface modification to generate greater implant stability and more rapid healing following implantation or the stimulation of MSCs ex vivo for reimplantation. This review aims to gather publications targeted at promoting, enhancing, and controlling the osteogenic differentiation of MSCs through biomaterials, nanotopographies, and modified surfaces for use in implant procedures.

  7. Surface analysis of gold nanoparticles functionalized with thiol-modified glucose SAMs for biosensor applications.

    Directory of Open Access Journals (Sweden)

    Valentina eSpampinato

    2016-02-01

    Full Text Available In this work, Time of Flight Secondary Ion Mass Spectrometry (ToF-SIMS, Principal Component Analysis (PCA and X-ray Photoelectron Spectroscopy (XPS have been used to characterize the surface chemistry of gold substrates before and after functionalization with thiol-modified glucose self-assembled monolayers and subsequent biochemical specific recognition of maltose binding protein (MBP.The results indicate that the surface functionalization is achieved both on flat and nanoparticles gold substrates thus showing the potential of the developed system as biodetection platform. Moreover, the method presented here has been found to be a sound and valid approach to characterize the surface chemistry of nanoparticles functionalized with large molecules.Both techniques were proved to be very useful tools for monitoring all the functionalization steps, including the investigation of the biological behaviour of the glucose-modified particles in presence of the maltose binding protein.

  8. Surface analysis of gold nanoparticles functionalized with thiol-modified glucose SAMs for biosensor applications.

    Science.gov (United States)

    Spampinato, Valentina; Parracino, Mariaantonietta; La Spina, Rita; Rossi, Francois; Ceccone, Giacomo

    2016-02-01

    In this work, Time of Flight Secondary Ion Mass Spectrometry (ToF-SIMS), Principal Component Analysis (PCA) and X-ray Photoelectron Spectroscopy (XPS) have been used to characterize the surface chemistry of gold substrates before and after functionalization with thiol-modified glucose self-assembled monolayers and subsequent biochemical specific recognition of maltose binding protein (MBP). The results indicate that the surface functionalization is achieved both on flat and nanoparticles gold substrates thus showing the potential of the developed system as biodetection platform. Moreover, the method presented here has been found to be a sound and valid approach to characterize the surface chemistry of nanoparticles functionalized with large molecules. Both techniques were proved to be very useful tools for monitoring all the functionalization steps, including the investigation of the biological behaviour of the glucose-modified particles in presence of the maltose binding protein.

  9. Numerical simulation of binary collisions using a modified surface tension model with particle method

    International Nuclear Information System (INIS)

    Sun Zhongguo; Xi Guang; Chen Xi

    2009-01-01

    The binary collision of liquid droplets is of both practical importance and fundamental value in computational fluid mechanics. We present a modified surface tension model within the moving particle semi-implicit (MPS) method, and carry out two-dimensional simulations to investigate the mechanisms of coalescence and separation of the droplets during binary collision. The modified surface tension model improves accuracy and convergence. A mechanism map is established for various possible deformation pathways encountered during binary collision, as the impact speed is varied; a new pathway is reported when the collision speed is critical. In addition, eccentric collisions are simulated and the effect of the rotation of coalesced particle is explored. The results qualitatively agree with experiments and the numerical protocol may find applications in studying free surface flows and interface deformation

  10. Bone Formation from Porcine Dental Germ Stem Cells on Surface Modified Polybutylene Succinate Scaffolds

    Directory of Open Access Journals (Sweden)

    Nergis Abay

    2016-01-01

    Full Text Available Designing and providing a scaffold are very important for the cells in tissue engineering. Polybutylene succinate (PBS has high potential as a scaffold for bone regeneration due to its capacity in cell proliferation and differentiation. Also, stem cells from 3rd molar tooth germs were favoured in this study due to their developmentally and replicatively immature nature. In this study, porcine dental germ stem cells (pDGSCs seeded PBS scaffolds were used to investigate the effects of surface modification with fibronectin or laminin on these scaffolds to improve cell attachment, proliferation, and osteogenic differentiation for tissue engineering applications. The osteogenic potentials of pDGSCs on these modified and unmodified foams were examined to heal bone defects and the effects of fibronectin or laminin modified PBS scaffolds on pDGSC differentiation into bone were compared for the first time. For this study, MTS assay was used to assess the cytotoxic effects of modified and unmodified surfaces. For the characterization of pDGSCs, flow cytometry analysis was carried out. Besides, alkaline phosphatase (ALP assay, von Kossa staining, real-time PCR, CM-Dil, and immunostaining were applied to analyze osteogenic potentials of pDGSCs. The results of these studies demonstrated that pDGSCs were differentiated into osteogenic cells on fibronectin modified PBS foams better than those on unmodified and laminin modified PBS foams.

  11. Synthesis and evaluation of modified chalcone based p53 stabilizing agents.

    Science.gov (United States)

    Iftikhar, Sunniya; Khan, Sardraz; Bilal, Aishah; Manzoor, Safia; Abdullah, Muhammad; Emwas, Abdel-Hamid; Sioud, Salim; Gao, Xin; Chotana, Ghayoor Abbas; Faisal, Amir; Saleem, Rahman Shah Zaib

    2017-09-01

    Tumor suppressor protein p53 induces cell cycle arrest and apoptotic cell death in response to various cellular stresses thereby preventing cancer development. Activation and stabilization of p53 through small organic molecules is, therefore, an attractive approach for the treatment of cancers retaining wild-type p53. In this context, a series of nineteen chalcones with various substitution patterns of functional groups including chloro, fluoro, methoxy, nitro, benzyloxy, 4-methyl benzyloxy was prepared using Claisen-Schmidt condensation. The compounds were characterized using NMR, HRMS, IR and melting points. Evaluation of synthesized compounds against human colorectal (HCT116) and breast (CAL-51) cancer cell lines revealed potent antiproliferative activities. Nine compounds displayed GI 50 values in the low micromolar to submicromolar range; for example (E)-1-phenyl-3-(3,4,5-trimethoxyphenyl)prop-2-en-1-one (SSE14108) showed GI 50 of 0.473±0.043µM against HCT116 cells. Further analysis of these compounds revealed that (E)-3-(4-chlorophenyl)-1-phenylprop-2-en-1-one (SSE14105) and (E)-3-(4-methoxyphenyl)-1-phenylprop-2-en-1-one (SSE14106) caused rapid (4 and 8-h post-treatment) accumulation of p53 in HCT116 cells similar to its induction by positive control, Nutlin-3. Such activities were absent in 3-(4-methoxyphenyl)propiophenone (SSE14106H2) demonstrating the importance of conjugated ketone for antiproliferative and p53 stabilizing activity of the chalcones. We further evaluated p53 levels in the presence of cycloheximide (CHX) and the results showed that the p53 stabilization was regulated at post-translational level through blockage of its degradation. These chalcones can, therefore, act as fragment leads for further structure optimization to obtain more potent p53 stabilizing agents with enhanced anti-proliferative activities. Copyright © 2017 Elsevier Ltd. All rights reserved.

  12. Synthesis and evaluation of modified chalcone based p53 stabilizing agents

    KAUST Repository

    Iftikhar, Sunniya

    2017-07-15

    Tumor suppressor protein p53 induces cell cycle arrest and apoptotic cell death in response to various cellular stresses thereby preventing cancer development. Activation and stabilization of p53 through small organic molecules is, therefore, an attractive approach for the treatment of cancers retaining wild-type p53. In this context, a series of nineteen chalcones with various substitution patterns of functional groups including chloro, fluoro, methoxy, nitro, benzyloxy, 4-methyl benzyloxy was prepared using Claisen-Schmidt condensation. The compounds were characterized using NMR, HRMS, IR and melting points. Evaluation of synthesized compounds against human colorectal (HCT116) and breast (Cal-51) cancer cell lines revealed potent antiproliferative activities. Nine compounds displayed GI50 values in the low micromolar to submicromolar range; for example (E)-1-phenyl-3-(3,4,5-trimethoxyphenyl)prop-2-en-1-one (SSE14108) showed GI50 of 0.473 ± 0.043 µM against HCT116 cells. Further analysis of these compounds revealed that (E)-3-(4-chlorophenyl)-1-phenylprop-2-en-1-one (SSE14105) and (E)-3-(4-methoxyphenyl)-1-phenylprop-2-en-1-one (SSE14106) caused rapid (4 and 8-hour post-treatment) accumulation of p53 in HCT116 cells similar to its induction by positive control, Nutlin-3. Such activities were absent in 3-(4-methoxyphenyl)propiophenone (SSE14106H2) demonstrating the importance of conjugated ketone for antiproliferative and p53 stabilizing activity of the chalcones. We further evaluated p53 levels in the presence of cycloheximide (CHX) and the results showed that the p53 stabilization was regulated at post-translational level through blockage of its degradation. These chalcones can, therefore, act as fragment leads for further structure optimization to obtain more potent p53 stabilizing agents with enhanced anti-proliferative activities.

  13. Biocompatible Chitosan Oligosaccharide Modified Gold Nanorods as Highly Effective Photothermal Agents for Ablation of Breast Cancer Cells

    Directory of Open Access Journals (Sweden)

    Panchanathan Manivasagan

    2018-02-01

    Full Text Available Photothermal therapy (PTT using biocompatible nanomaterials have recently attracted much attention as a novel candidate technique for cancer therapy. In this work we report the performance of newly synthesized multidentate chitosan oligosaccharide modified gold nanorods (AuNRs-LA-COS as novel agents for PTT of cancer cells due to their excellent biocompatibility, photothermal stability, and high absorption in the near-infrared (NIR region. The AuNRs-LA-COS exhibit a strong NIR absorption peak at 838 nm with a mean length of 26 ± 3.1 nm and diameter of 6.8 ± 1.7 nm, respectively. The temperature of AuNRs-LA-COS rapidly reached 52.6 °C for 5 min of NIR laser irradiation at 2 W/cm2. The AuNRs-LA-COS had very low cytotoxicity and exhibited high efficiency for the ablation of breast cancer cells in vitro. The tumor-bearing mice were completely ablated without tumor recurrence after photothermal treatment with AuNRs-LA-COS (25 µg/mL under laser irradiation. In summary, this study demonstrated that AuNRs-LA-COS with laser irradiation as novel agents pave an alternative way for breast cancer therapy and hold great promise for clinical trials in the near future.

  14. Effects of irradiation, antimicrobial agents and modified packaging on histamine production by Morganella morganii in mackerel fillets

    International Nuclear Information System (INIS)

    Aytac, S.A.; Ozbas, Z.Y.; Vural, H.

    2000-01-01

    The effects of gamma irradiation (0.5 and 2.0 kGy), antimicrobial agents (5% sodium chloride and 1% potassium sorbate) and modified atmosphere (100% CO2) packaging (MAP) on histamine production by Morganella morganii were examined in mackerel fillets during 8 days of cold storage. MAP combined with antimicrobial agents was also applied to the fillets. The changes in histamine levels, M. morganii and total aerobic bacterial counts were determined during the storage. All methods used in this study showed beneficial effect in controlling bacterial growth and histamine production on mackerel fillets during 2-3 days of storage. MAP combined with 5% sodium chloride has more retarding effect on production of histamine than the other methods. For M. morganii, maximum inhibition effect was found at the dose of 2.0 kGy. Irradiation with a dose of 2.0 kGy, MAP combined with sodium chloride and MAP were also found to have the most inhibiting effects on total aerobic bacterial count during the storage

  15. Nicotine–magnesium aluminum silicate microparticle surface modified with chitosan for mucosal delivery

    Energy Technology Data Exchange (ETDEWEB)

    Kanjanakawinkul, Watchara [Faculty of Pharmaceutical Sciences, Khon Kaen University, Khon Kaen 40002 (Thailand); Rades, Thomas [School of Pharmacy, University of Otago, Dunedin 9054 (New Zealand); Department of Pharmacy, Faculty of Health and Medical Sciences, University of Copenhagen, DK-2100 Copenhagen (Denmark); Puttipipatkhachorn, Satit [Department of Manufacturing Pharmacy, Faculty of Pharmacy, Mahidol University, Bangkok 10400 (Thailand); Pongjanyakul, Thaned, E-mail: thaned@kku.ac.th [Faculty of Pharmaceutical Sciences, Khon Kaen University, Khon Kaen 40002 (Thailand)

    2013-04-01

    Magnesium aluminum silicate (MAS), a negatively charged clay, and nicotine (NCT), a basic drug, can interact electrostatically to form microparticles. Chitosan (CS) was used for the surface modification of the microparticles, and a lyophilization method was used to preserve the original particle morphology. The microparticles were characterized in terms of their physicochemical properties, NCT content, mucoadhesive properties, and release and permeation across porcine esophageal mucosa. The results showed that the microparticles formed via electrostatic interaction between MAS and protonated NCT had an irregular shape and that their NCT content increased with increasing NCT ratios in the microparticle preparation solution. High molecular weight CS (800 kDa) adsorbed to the microparticle surface and induced a positive surface charge. CS molecules intercalated into the MAS silicate layers and decreased the crystallinity of the microparticles, leading to an increase in the release rate and diffusion coefficient of NCT from the microparticles. Moreover, the microparticle surface modified with CS was found to have higher NCT permeation fluxes and mucoadhesive properties, which indicated the significant role of CS for NCT mucosal delivery. However, the enhancement of NCT permeation and of mucoadhesive properties depended on the molecular weight and concentration of CS. These findings suggest that NCT-MAS microparticle surface modified with CS represents a promising mucosal delivery system for NCT. Highlights: ► Nicotine–magnesium aluminum silicate microparticles were prepared using electrostatic interaction. ► Lyophilization was used for drying and maintaining an original morphology of the microparticles. ► Chitosan (CS) was used for surface modification of the microparticles at acidic pH. ► Surface modification using CS caused an increase in release and permeation of nicotine. ► Microparticle surface-modified with CS presented better mucoadhesive properties.

  16. Evaluation of performance of modified sodium lignosulfonate additives as reinforcing agent in porcelain stoneware tiles

    Directory of Open Access Journals (Sweden)

    Rastelli, E.

    2010-10-01

    Full Text Available A sodium salt of a modified lignosulfonate at different percentages was added to a porcelain stoneware suspension and the effects on the rheological properties of slips and on the mechanical properties of prepared samples were investigated. As the presence of sulfonates groups can change the stability of dispersion, a rheological characterisation was necessary to find the critical concentration to obtain well dispersed suspensions and high MOR values. The suspensions stability was tested by oscillatory measurements and the increase of elastic modulus in the suspension corresponded to a MOR and to Young’s modulus increase as well. Finally, to explain the results obtained by the mechanical characterisation of the prepared samples, a model drawing on the composite materials experience, is suggested.

    Usando distintos porcentajes, se añadió sal de sodio de un lignosulfonato modificado, a una suspensión de gres porcelánico, y se investigaron los efectos sobre las propiedades reológicas de las suspensiones y sobre las propiedades mecánicas de las muestras preparadas. Debido a que la presencia de grupos de sulfonatos puede modificar la estabilidad de la dispersión, fue necesario realizar una caracterización reológica para averiguar la concentración crítica necesaria para la obtención de suspensiones bien dispersas y altos valores de MOR. Se analizó la estabilidad de las suspensiones por medio de mediciones oscilatorias y el incremento del módulo elástico en la suspensión que corresponde al incremento de un módulo MOR y de un módulo de Young también. Finalmente, para explicar los resultados obtenidos por medio de la caracterización mecánica de las muestras preparadas, se sugiere un modelo que parte de la experiencia con los materiales compuestos.

  17. Shear Resistance Properties of Modified Nano-SiO2/AA/AM Copolymer Oil Displacement Agent

    Directory of Open Access Journals (Sweden)

    Nanjun Lai

    2016-12-01

    Full Text Available To address the problem regarding poor shear resistance of commonly employed polymers for oil displacement, modified nano-SiO2/AA/AM copolymer (HPMNS oil displacement agents were synthesized using acrylic acid (AA, acrylamide (AM, and modified nano-SiO2 of different modification degrees as raw materials. HPMNS was characterized by means of infrared spectroscopy (IR, nuclear magnetic resonance (1H-NMR, 13C-NMR, dynamic/static light scattering, and scanning electron microscope. A comparative study of the shear resistance properties for partially hydrolyzed polyacrylamide (HPAM and HPMNS was conducted. Compared to HPAM, the introduced hyperbranched structure endowed HPMNS with good shear resistance, which was quantified from the viscosity retention ratio of the polymer solutions. From the perspective of rheological property, HPMNS also showed great shear stability after shearing by a Mixing Speed Governor and porous media shear model. Furthermore, with a higher degree of modification, HPMNS-2 had better shear stability in terms of viscosity and rheological property than HPMNS-1. The phenomena were due to its lower hydrodynamic radius, weight-average molecular weight, and better flexibility of its molecular chains. In addition, upon the indoor displacement test, the resistance factor and residual resistance factor values of HPMNS-2 were higher than those of HPAM. This behavior is beneficial for increasing oil recovery.

  18. Surface characterization and corrosion behavior of micro-arc oxidized Ti surface modified with hydrothermal treatment and chitosan coating

    International Nuclear Information System (INIS)

    Neupane, Madhav Prasad; Park, Il Song; Lee, Min Ho

    2014-01-01

    In the present work, we describe the surface modification of commercially pure titanium (CP-Ti) by a composite/multilayer coating approach for biomedical applications. CP-Ti samples were treated by micro-arc oxidation (MAO) and subsequently some of the samples were coated with chitosan (Chi) by dip coating method, while others were subjected to hydrothermal treatment (HT) followed by chitosan coating. The MAO, MAO/Chi, and MAO/HT/Chi coated Ti were characterized and their characteristics were compared with CP-Ti. X-ray diffraction and scanning electron microscopy were used to assess the structural and morphological characteristics. The average surface roughness was determined using a surface profilometer. The corrosion resistance of untreated and surface modified Ti in commercial saline at 298 K was evaluated by potentiodynamic polarization test. The results indicated that the chitosan coating is very well integrated with the MAO and MAO/HT coating by physically interlocking itself with the coated layer and almost sealed all the pores. The surface roughness of hydrothermally treated and chitosan coated MAO film was superior evidently to that with other sample groups. The corrosion studies demonstrated that the MAO, hydrothermally treated and chitosan coated sample enhanced the corrosion resistance of titanium. The result indicates that fabrication of hydrothermally treated MAO surface coatings with chitosan is a significant approach to protect the titanium from corrosion, hence enhancing the potential use of titanium as bio-implants. - Highlights: • Micro-arc oxidized (MAO) and hydrothermally treated (HT) Ti surfaces are coated with chitosan (Chi). • The MAO/HT/Chi surface exhibits pores sealing and enhanced the surface roughness. • The MAO/HT/Chi surface significantly increase the corrosion resistance. • The MAO/HT/Chi can be a potential surface of titanium for bio-implants

  19. Toxicity of surface-modified copper oxide nanoparticles in a mouse macrophage cell line: Interplay of particles, surface coating and particle dissolution.

    Science.gov (United States)

    Líbalová, Helena; Costa, Pedro M; Olsson, Magnus; Farcal, Lucian; Ortelli, Simona; Blosi, Magda; Topinka, Jan; Costa, Anna L; Fadeel, Bengt

    2018-04-01

    The rapid dissolution of copper oxide (CuO) nanoparticles (NPs) with release of ions is thought to be one of the main factors modulating their toxicity. Here we assessed the cytotoxicity of a panel of CuO NPs (12 nm ± 4 nm) with different surface modifications, i.e., anionic sodium citrate (CIT) and sodium ascorbate (ASC), neutral polyvinylpyrrolidone (PVP), and cationic polyethylenimine (PEI), versus the pristine (uncoated) NPs, using a murine macrophage cell line (RAW264.7). Cytotoxicity, reactive oxygen species (ROS) production, and cellular uptake were assessed. The cytotoxicity results were analyzed by the benchmark dose (BMD) method and the NPs were ranked based on BMD 20 values. The PEI-coated NPs were found to be the most cytotoxic. Despite the different properties of the coating agents, NP dissolution in cell medium was only marginally affected by surface modification. Furthermore, CuCl 2 (used as an ion control) elicited significantly less cytotoxicity when compared to the CuO NPs. We also observed that the antioxidant, N-acetylcysteine, failed to protect against the cytotoxicity of the uncoated CuO NPs. Indeed, the toxicity of the surface-modified CuO NPs was not directly linked to particle dissolution and subsequent Cu burden in cells, nor to cellular ROS production, although CuO-ASC NPs, which were found to be the least cytotoxic, yielded lower levels of ROS in comparison to pristine NPs. Hierarchical cluster analysis suggested, instead, that the toxicity in the current in vitro model could be explained by synergistic interactions between the NPs, their dissolution, and the toxicity of the coating agents. Copyright © 2017 Elsevier Ltd. All rights reserved.

  20. Interaction of insulin with colloidal ZnS quantum dots functionalized by various surface capping agents.

    Science.gov (United States)

    Hosseinzadeh, Ghader; Maghari, Ali; Farniya, Seyed Morteza Famil; Keihan, Amir Homayoun; Moosavi-Movahedi, Ali A

    2017-08-01

    Interaction of quantum dots (QDs) and proteins strongly influenced by the surface characteristics of the QDs at the protein-QD interface. For a precise control of these surface-related interactions, it is necessary to improve our understanding in this field. In this regard, in the present work, the interaction between the insulin and differently functionalized ZnS quantum dots (QDs) were studied. The ZnS QDs were functionalized with various functional groups of hydroxyl (OH), carboxyl (COOH), amine (NH 2 ), and amino acid (COOH and NH 2 ). The effect of surface hydrophobicity was also studied by changing the alkyl-chain lengths of mercaptocarboxylic acid capping agents. The interaction between insulin and the ZnS QDs were investigated by fluorescence quenching, synchronous fluorescence, circular dichroism (CD), and thermal aggregation techniques. The results reveal that among the studied QDs, mercaptosuccinic acid functionalized QDs has the strongest interaction (∆G ° =-51.50kJ/mol at 310K) with insulin, mercaptoethanol functionalized QDs destabilize insulin by increasing the beta-sheet contents, and only cysteine functionalized QDs improves the insulin stability by increasing the alpha-helix contents of the protein, and. Our results also indicate that by increasing the alkyl-chain length of capping agents, due to an increase in hydrophobicity of the QDs surface, the beta-sheet contents of insulin increase which results in the enhancement of insulin instability. Copyright © 2017 Elsevier B.V. All rights reserved.

  1. Electrochemical Biosensor Based on Boron-Doped Diamond Electrodes with Modified Surfaces

    Directory of Open Access Journals (Sweden)

    Yuan Yu

    2012-01-01

    Full Text Available Boron-doped diamond (BDD thin films, as one kind of electrode materials, are superior to conventional carbon-based materials including carbon paste, porous carbon, glassy carbon (GC, carbon nanotubes in terms of high stability, wide potential window, low background current, and good biocompatibility. Electrochemical biosensor based on BDD electrodes have attracted extensive interests due to the superior properties of BDD electrodes and the merits of biosensors, such as specificity, sensitivity, and fast response. Electrochemical reactions perform at the interface between electrolyte solutions and the electrodes surfaces, so the surface structures and properties of the BDD electrodes are important for electrochemical detection. In this paper, the recent advances of BDD electrodes with different surfaces including nanostructured surface and chemically modified surface, for the construction of various electrochemical biosensors, were described.

  2. Surface characteristics analysis of dry EDMed AISI D2 steel using modified tool design

    International Nuclear Information System (INIS)

    Pragadish, N.; Kumar, M. Pradeep

    2015-01-01

    A modified tool design is proposed which helps in drilling holes without any central core, and also enables the effective removal of the debris particles. Experiments were conducted on AISI D2 Steel using copper electrode as tool in both conventional EDM and dry EDM processes and the performance of both processes is compared. Experiments were designed using Taguchi's L27 orthogonal array. Discharge current (I), gap voltage (V), pulse on time (T ON ), gas pressure (P) and tool rotational speed (N) were chosen as the various input parameters, and their effect on the material removal rate (MRR), surface roughness (SR), surface morphology, microstructure and elemental composition of the machined surface is analyzed. The experimental results show better surface characteristics in the surface machined under dry EDM process.

  3. Effects of modified surfaces produced at plasma-facing surface on hydrogen release behavior in the LHD

    Directory of Open Access Journals (Sweden)

    Y. Nobuta

    2017-08-01

    Full Text Available In the present study, an additional deuterium (D ion irradiation was performed against long-term samples mounted on the helical coil can and in the outer private region in the LHD during the 17th experimental campaign. Based on the release behavior of the D and hydrogen (H retained during the experimental campaign, the difference of release behavior at the top surface and in bulk of modified surfaces is discussed. Almost all samples on the helical coil can were erosion-dominant and some samples were covered with boron or carbon, while a very thick carbon films were formed in the outer private region. In the erosion-dominant area, the D desorbed at much lower temperatures compared to that of H retained during the LHD plasma operation. For the samples covered with boron, the D tended to desorb at lower temperatures compared to H. For the carbon deposition samples, the D desorbed at much higher temperatures compared to no deposition and boron-covered samples, which was very similar to that of H. The D retention capabilities at the top surface of carbon and boron films were 2–3 times higher than no deposition area. The results indicate that the retention and release behavior at the top surface of the modified layer can be different from that of bulk substrate material.

  4. Surface-modified silica colloidal crystals: nanoporous films and membranes with controlled ionic and molecular transport.

    Science.gov (United States)

    Zharov, Ilya; Khabibullin, Amir

    2014-02-18

    Nanoporous membranes are important for the study of the transport of small molecules and macromolecules through confined spaces and in applications ranging from separation of biomacromolecules and pharmaceuticals to sensing and controlled release of drugs. For many of these applications, chemists need to gate the ionic and molecular flux through the nanopores, which in turn depends on the ability to control the nanopore geometry and surface chemistry. Most commonly used nanoporous membrane materials are based on polymers. However, the nanostructure of polymeric membranes is not well-defined, and their surface is hard to modify. Inorganic nanoporous materials are attractive alternatives for polymers in the preparation of nanoporous membranes. In this Account, we describe the preparation and surface modification of inorganic nanoporous films and membranes self-assembled from silica colloidal spheres. These spheres form colloidal crystals with close-packed face centered cubic lattices upon vertical deposition from colloidal solutions. Silica colloidal crystals contain ordered arrays of interconnected three dimensional voids, which function as nanopores. We can prepare silica colloidal crystals as supported thin films on various flat solid surfaces or obtain free-standing silica colloidal membranes by sintering the colloidal crystals above 1000 °C. Unmodified silica colloidal membranes are capable of size-selective separation of macromolecules, and we can surface-modify them in a well-defined and controlled manner with small molecules and polymers. For the surface modification with small molecules, we use silanol chemistry. We grow polymer brushes with narrow molecular weight distribution and controlled length on the colloidal nanopore surface using atom transfer radical polymerization or ring-opening polymerization. We can control the flux in the resulting surface-modified nanoporous films and membranes by pH and ionic strength, temperature, light, and small molecule

  5. [Effects of tooth whitening agents and acidic drinks on the surface properties of dental enamel].

    Science.gov (United States)

    Chen, Xiaoling; Chen, Zhiqun; Lin, Yao; Shao, Jinquan; Yin, Lu

    2013-10-01

    Using tooth whitening agents (bleaching clip) in vitro and acidic drinks, we conducted a comparative study of the changes in enamel surface morphology, Ca/P content, and hardness. Tooth whitening glue pieces, cola, and orange juice were used to soak teeth in artificial saliva in vitro. Physiological saline was used as a control treatment. The morphology of the four groups was observed under a scanning electron microscope (SEM) immediately after the teeth were soaked for 7 and 14 d. The changes in Ca/P content and microhardness were analyzed. The enamel surfaces of the teeth in the three test groups were demineralized. The Ca/P ratio and the average microhardness were significantly lower than those of the control group immediately after the teeth were soaked (P 0.05). Bleaching agents caused transient demineralization of human enamel, but these agents could induce re-mineralization and repair of enamel over time. Demineralization caused by bleaching covered a relatively normal range compared with acidic drinks and daily drinking.

  6. Surface Modified Characteristics of the Tetracalcium Phosphate as Light-Cured Composite Resin Fillers

    Directory of Open Access Journals (Sweden)

    Wen-Cheng Chen

    2014-01-01

    Full Text Available The objectives of this study are to characterize the properties of light-cured composite resins that are reinforced with whisker surface-modified particles of tetracalcium phosphate (TTCP and to investigate the influence of thermal cycling on the reinforced composites properties. The characteristics of ultimate diametral tensile strength (DTS, moduli, pH values, and fracture surfaces of the samples with different amounts of surface-modified TTCP (30%–60% were determined before and after thermal cycling between 5°C and 55°C in deionized water for 600 cycles. The trends of all groups were ductile prior to thermal cycling and the moduli of all groups increased after thermal cycling. The ductile property of the control group without filler was not significantly affected. Larger amounts of fillers caused the particles to aggregate, subsequently decreasing the resin’s ability to disperse external forces and leading to brittleness after thermal cycling. Therefore, the trend of composite resins with larger amounts of filler would become more brittle and exhibited higher moduli after thermal cycling. This developed composite resin with surface modified-TTCP fillers has the potential to be successful dental restorative materials.

  7. Protein arrangement on modified diamond-like carbon surfaces – An ARXPS study

    International Nuclear Information System (INIS)

    Oosterbeek, Reece N.; Seal, Christopher K.; Hyland, Margaret M.

    2014-01-01

    Highlights: • DLC coatings were modified by Ar + ion sputtering and laser graphitisation. • The surface properties of the coatings were measured, and it was found that the above methods increased sp 2 content and altered surface energy. • ARXPS was used to observe protein arrangement on the surface. • Polar CO/CN groups were seen to be segregated towards the interface, indicating they play an important role in bonding. • This segregation increased with increasing polar surface energy, indicating an increased net attraction between polar groups. - Abstract: Understanding the nature of the interface between a biomaterial implant and the biological fluid is an essential step towards creating improved implant materials. This study examined a diamond-like carbon coating biomaterial, the surface energy of which was modified by Ar + ion sputtering and laser graphitisation. The arrangement of proteins was analysed by angle resolved X-ray photoelectron spectroscopy, and the effects of the polar component of surface energy on this arrangement were observed. It was seen that polar groups (such as CN, CO) are more attracted to the coating surface due to the stronger polar interactions. This results in a segregation of these groups to the DLC–protein interface; at increasing takeoff angle (further from to DLC–protein interface) fewer of these polar groups are seen. Correspondingly, groups that interact mainly by dispersive forces (CC, CH) were found to increase in intensity as takeoff angle increased, indicating they are segregated away from the DLC–protein interface. The magnitude of the segregation was seen to increase with increasing polar surface energy, this was attributed to an increased net attraction between the solid surface and polar groups at higher polar surface energy (γ S p )

  8. Protein arrangement on modified diamond-like carbon surfaces – An ARXPS study

    Energy Technology Data Exchange (ETDEWEB)

    Oosterbeek, Reece N., E-mail: reece.oosterbeek@auckland.ac.nz [Department of Chemical and Materials Engineering, The University of Auckland, Private Bag 92019 (New Zealand); Seal, Christopher K. [Light Metals Research Centre, The University of Auckland, Private Bag 92019 (New Zealand); Hyland, Margaret M. [Department of Chemical and Materials Engineering, The University of Auckland, Private Bag 92019 (New Zealand)

    2014-12-01

    Highlights: • DLC coatings were modified by Ar{sup +} ion sputtering and laser graphitisation. • The surface properties of the coatings were measured, and it was found that the above methods increased sp{sup 2} content and altered surface energy. • ARXPS was used to observe protein arrangement on the surface. • Polar CO/CN groups were seen to be segregated towards the interface, indicating they play an important role in bonding. • This segregation increased with increasing polar surface energy, indicating an increased net attraction between polar groups. - Abstract: Understanding the nature of the interface between a biomaterial implant and the biological fluid is an essential step towards creating improved implant materials. This study examined a diamond-like carbon coating biomaterial, the surface energy of which was modified by Ar{sup +} ion sputtering and laser graphitisation. The arrangement of proteins was analysed by angle resolved X-ray photoelectron spectroscopy, and the effects of the polar component of surface energy on this arrangement were observed. It was seen that polar groups (such as CN, CO) are more attracted to the coating surface due to the stronger polar interactions. This results in a segregation of these groups to the DLC–protein interface; at increasing takeoff angle (further from to DLC–protein interface) fewer of these polar groups are seen. Correspondingly, groups that interact mainly by dispersive forces (CC, CH) were found to increase in intensity as takeoff angle increased, indicating they are segregated away from the DLC–protein interface. The magnitude of the segregation was seen to increase with increasing polar surface energy, this was attributed to an increased net attraction between the solid surface and polar groups at higher polar surface energy (γ{sub S}{sup p})

  9. Development of the removal technology for toxic heavy metal ions by surface-modified activated carbon

    Energy Technology Data Exchange (ETDEWEB)

    Park, Geun Il; Song, Kee Chan; Kim, Kwang Wook; Kim, In Tae; Cho, Il Hoon; Kim, Joon Hyung

    2001-01-01

    Adsorption capacities of both radionuclides(uranium, cobalt) and toxic heavy metals (lead, cadmium and chromium) using double surface-modified activated carbon in wide pH ranges are extensively evaluated. Surface-modified activated carbons are classified as AC(as-received carbon), OAC(single surface-modified carbon with nitric acid solution) and OAC-Na(double surface-modified carbon with various alkali solutions). It is established that optimal condition for the second surface modification of OAC is to use the mixed solution of both NaOH and NaCl with total concentration of 0.1 N based on adsorption efficiencies of uranium and cobalt. Variations of adsorption efficiencies in pH ranges of 2{approx}10 and the adsorption capacities in batch adsorber and fixed bed for removal of both radionuclides and toxic heavy metals using OAC-Na were shown to be superior to that of the AC and OAC even in a low pH range. Capacity factors of OAC-Na for the removal of various metal ions are also excellent to that of AC or OAC. Quantitative analysis of capacity factors for each ions showed that adsorption capacity of OAC-Na increased by 30 times for uranium, 60 times for cobalt, 9 times for lead, 30 times for cadmium, 3 times for chromium compared to that of AC at pH 5, respectively. Adsorption capacity of OAC-Na is comparable to that of XAD-16-TAR used as commercial ion exchange resin.

  10. Structure–Property Relationships of Inorganically Surface-Modified Zeolite Molecular Sieves for Nanocomposite Membrane Fabrication

    KAUST Repository

    Lydon, Megan E.

    2012-05-03

    A multiscale experimental study of the structural, compositional, and morphological characteristics of aluminosilicate (LTA) and pure-silica (MFI) zeolite materials surface-modified with MgO xH y nanostructures is presented. These characteristics are correlated with the suitability of such materials in the fabrication of LTA/Matrimid mixed-matrix membranes (MMMs) for CO 2/CH 4 separations. The four functionalization methods studied in this work produce surface nanostructures that may appear superficially similar under SEM observation but in fact differ considerably in shape, size, surface coverage, surface area/roughness, degree of attachment to the zeolite surface, and degree of zeolite pore blocking. The evaluation of these characteristics by a combination of TEM, HRTEM, N 2 physisorption, multiscale compositional analysis (XPS, EDX, and ICP-AES elemental analysis), and diffraction (ED and XRD) allows improved understanding of the origin of disparate gas permeation properties observed in MMMs made with four types of surface-modified zeolite LTA materials, as well as a rational selection of the method expected to result in the best enhancement of the desired properties (in the present case, CO 2/CH 4 selectivity increase without sacrificing permeability). A method based on ion exchange of the LTA with Mg 2+, followed by base-induced precipitation and growth of MgO xH y nanostructures, deemed "ion exchange functionalization" here, offers modified particles with the best overall characteristics resulting in the most effective MMMs. LTA/Matrimid MMMs containing ion exchange functionalized particles had a considerably higher CO 2/CH 4 selectivity (∼40) than could be obtained with the other functionalization techniques (∼30), while maintaining a CO 2 permeability of ∼10 barrers. A parallel study on pure silica MFI surface nanostructures is also presented to compare and contrast with the zeolite LTA case. © 2012 American Chemical Society.

  11. Controlled release study of an anti-carcinogenic agent, gallate from the surface of magnetite nanoparticles

    Science.gov (United States)

    Ghotbi, Mohammad Yeganeh; bin Hussein, Mohd Zobir

    2012-07-01

    Immobilization of gallate anion, an anti-carcinogenic, anti-mutagenic, and anti-microbial agent on the surface of magnetite nanoparticles was accomplished by adsorption technique for the formation of a core-shell nanocomposite. A simple co-precipitation technique in the presence of poly vinyl pyrrolidone was successfully applied for the preparation of magnetite nanoparticles as core beads with narrow size distribution. The powders were characterized by X-ray diffraction, particle size analysis, magnetic measurements, atomic force microscope and also infrared spectroscopy. FTIR and CHNS results indicated that the gallate anion was actually adsorbed onto the surface of the magnetite nanoparticles. The release of the anion from the surface of the nanocomposite was found to be controllable by the selection of the release media.

  12. Hydrolytic Stability of 3-Aminopropylsilane Coupling Agent on Silica and Silicate Surfaces at Elevated Temperatures

    DEFF Research Database (Denmark)

    Okhrimenko, Denis; Budi, Akin; Ceccato, Marcel

    2017-01-01

    in coupling efficiency, thus decreasing the product quality and the mechanical strength of the polymer-inorganic material interface. Therefore, a better understanding of the chemical state and stability of APS on inorganic surfaces is needed. In this work, we investigated APS adhesion on silica wafers...... and compared its properties with those on complex silicate surfaces such as those used by industry (mineral fibers and fiber melt wafers). The APS was deposited from aqueous and organic (toluene) solutions and studied with surface sensitive techniques, including X-ray photoelectron spectroscopy (XPS), atomic......- and laboratory-scale APS deposition methods and increasing adhesion and stability, thus increasing the quality and effectiveness of materials where APS is used as a coupling agent....

  13. The structural and surface properties of natural and modified coal gangue.

    Science.gov (United States)

    Jabłońska, Beata; Kityk, Andriy V; Busch, Mark; Huber, Patrick

    2017-04-01

    A novel application of coal gangue as inexpensive adsorbents is considered in this study. The structural and surface properties of natural and modified gangue were studied via nitrogen adsorption. Four types of samples were studied: natural, modified with H 2 NO 3 and H 2 O 2 and calcined at 250 °C and 600 °C. The specific surface area and porosity of the samples were determined using various methods. The raw material is mainly mesoporous with relatively small specific surface area. The chemical modification enlarged the total pore volume and the specific surface area. The calcination at 250 °C enlarged slightly the pore volume and lowered the specific surface area, but did not cause significant changes in the structural properties. The calcination at 600 °C resulted in a significant increase in pore volume and a decrease in specific surface area. These results suggest that the coal gangue studied here could be used as inexpensive adsorbent in industrial wastewater pretreatment. Copyright © 2016 Elsevier Ltd. All rights reserved.

  14. Plaque formation on surface modified dental implants. An in vitro study.

    Science.gov (United States)

    Grössner-Schreiber, B; Griepentrog, M; Haustein, I; Müller, W D; Lange, K P; Briedigkeit, H; Göbel, U B

    2001-12-01

    Bacterial adhesion on titanium implant surfaces has a strong influence on healing and long-term outcome of dental implants. Parameters like surface roughness and chemical composition of the implant surface were found to have a significant impact on plaque formation. The purpose of this study was to evaluate the influence of two physical hard coatings on bacterial adhesion in comparison with control surfaces of equivalent roughness. Two members of the oral microflora, Streptococcus mutans and Streptococcus sanguis were used. Commercially pure titanium discs were modified using four different surface treatments: physical vapour deposition (PVD) with either titanium nitride (TiN) or zirconium nitride (ZrN), thermal oxidation and structuring with laser radiation. Polished titanium surfaces were used as controls. Surface topography was examined by SEM and estimation of surface roughness was done using a contact stylus profilometer. Contact angle measurements were carried out to calculate surface energy. Titanium discs were incubated in the respective bacterial cell suspension for one hour and single colonies formed by adhering bacteria were counted by fluorescence microscopy. Contact angle measurements showed no significant differences between the surface modifications. The surface roughness (Ra) of all surfaces examined was between 0.14 and 1.00 microm. A significant reduction of the number of adherent bacteria was observed on inherently stable titanium hard materials such as TiN and ZrN and thermically oxidated titanium surfaces compared to polished titanium. In conclusion, physical modification of titanium implant surfaces such as coating with TiN or ZrN may reduce bacterial adherence and hence improve clinical results.

  15. Research on None Uniform Rational B-spline Surface and Agent for Numerically Controlled Layout Design

    Directory of Open Access Journals (Sweden)

    Zhigang XU

    2014-07-01

    Full Text Available Research on the integrated NC conceptual layout design (I-NCC concerned with a broader area of interests. The key issues of I-NCC system are associated with NURBS and agent. Firstly, formulas for the derivatives and normal vectors of non-rational B-spline and NURBS are proved based on de BOOR’s recursive formula. Compared with the existing approaches targeting at the non-rational B- spline basis functions, these equations are directly targeted at the controlling points, so the algorithms and programs for NURBS curve and surface can also be applied to the derivatives and normals, the calculating performance is increased. A simplified equation is also proved in this paper. Secondly, the NC conceptual configuration design is transformed into a 3D cuboids layout problem by the introduction of three typical modules: translation module, rotation module and base module based on the analysis of the normal unit vector of work piece surface (in NURBS format. 3D cuboids layout problem is viewed as a generalization of the quadratic assignment problem and therefore belongs to the class of NP hard problems. Apart from the complexity and variety of 3D layout optimization algorithms, this paper introduces agent oriented cooperative design system. Agent models and the corresponding design management systems are put forward to deal with the creative NC layout design. Though the key theoretical issues are now applied to the NC system design, there should be more industrial applications because of the prevalent proliferation nature of NURBS and agent.

  16. In situ surface-enhanced Raman spectroelectrochemical analysis system with a hemin modified nanostructured gold surface.

    Science.gov (United States)

    Yuan, Tao; Le Thi Ngoc, Loan; van Nieuwkasteele, Jan; Odijk, Mathieu; van den Berg, Albert; Permentier, Hjalmar; Bischoff, Rainer; Carlen, Edwin T

    2015-03-03

    An integrated surface-enhanced Raman scattering (SERS) spectroelectrochemical (SEC) analysis system is presented that combines a small volume microfluidic sample chamber (Raman spectroelectrochemistry. The SEC system includes a nanostructured Au surface that serves dual roles as the electrochemical working electrode (WE) and SERS substrate, a microfabricated Pt counter electrode (CE), and an external Ag/AgCl reference electrode (RE). The nanostructured Au WE enables highly sensitive in situ SERS spectroscopy through large and reproducible SERS enhancements, which eliminates the need for resonant wavelength matching of the laser excitation source with the electronic absorption of the target molecule. The new SEC analysis system has the merits of wide applicability to target molecules, small sample volume, and a low detection limit. We demonstrate in situ SERS spectroelectrochemistry measurements of the metalloporphyrin hemin showing shifts of the iron oxidation marker band ν4 with the nanostructured Au working electrode under precise potential control.

  17. Acute and subchronic toxicity analysis of surface modified paclitaxel attached hydroxyapatite and titanium dioxide nanoparticles.

    Science.gov (United States)

    Venkatasubbu, Gopinath Devanand; Ramasamy, S; Gaddam, Pramod Reddy; Kumar, J

    2015-01-01

    Nanoparticles are widely used for targeted drug delivery applications. Surface modification with appropriate polymer and ligands is carried out to target the drug to the affected area. Toxicity analysis is carried out to evaluate the safety of the surface modified nanoparticles. In this study, paclitaxel attached, folic acid functionalized, polyethylene glycol modified hydroxyapatite and titanium dioxide nanoparticles were used for targeted drug delivery system. The toxicological behavior of the system was studied in vivo in rats and mice. Acute and subchronic studies were carried out. Biochemical, hematological, and histopathological analysis was also done. There were no significant alterations in the biochemical parameters at a low dosage. There was a small change in alkaline phosphatase (ALP) level at a high dosage. The results indicate a safe toxicological profile.

  18. Surface and protein analyses of normal human cell attachment on PIII-modified chitosan membranes

    Energy Technology Data Exchange (ETDEWEB)

    Saranwong, N. [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Inthanon, K. [Human and Animal Cell Technology Research Laboratory, Department of Biology, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Wongkham, W., E-mail: weerah@chiangmai.ac.th [Human and Animal Cell Technology Research Laboratory, Department of Biology, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Wanichapichart, P. [Nanotechnology Center of Excellence and Membrane Science and Technology Research Center, Department of Physics, Faculty of Science, Prince of Songkla University, Hat Yai, Songkla 90110 (Thailand); Suwannakachorn, D. [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Yu, L.D., E-mail: yuld@fnrf.science.cmu.ac.th [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Thailand Center of Excellence in Physics, Commission on Higher Education, 328 Si Ayutthaya Road, Bangkok 10400 (Thailand)

    2012-02-01

    Surface of chitosan membrane was modified with argon (Ar) and nitrogen (N) plasma immersion ion implantation (PIII) for human skin fibroblasts F1544 cell attachment. The modified surfaces were characterized by Fourier transform infrared spectroscopy (FTIR) and atomic force microscopy (AFM). Cell attachment patterns were evaluated by scanning electron microscopy (SEM). The enzyme-linked immunosorbent assay (ELISA) was used to quantify levels of focal adhesion kinase (FAK). The results showed that Ar PIII had an enhancement effect on the cell attachment while N-PIII had an inhibition effect. Filopodial analysis revealed more microfilament cytoplasmic spreading on the edge of cells attached on the Ar-treated membranes than N-treated membranes. Higher level FAK was found in Ar-treated membranes than that in N-treated membranes.

  19. Acute and subchronic toxicity analysis of surface modified paclitaxel attached hydroxyapatite and titanium dioxide nanoparticles

    Science.gov (United States)

    Venkatasubbu, Gopinath Devanand; Ramasamy, S; Gaddam, Pramod Reddy; Kumar, J

    2015-01-01

    Nanoparticles are widely used for targeted drug delivery applications. Surface modification with appropriate polymer and ligands is carried out to target the drug to the affected area. Toxicity analysis is carried out to evaluate the safety of the surface modified nanoparticles. In this study, paclitaxel attached, folic acid functionalized, polyethylene glycol modified hydroxyapatite and titanium dioxide nanoparticles were used for targeted drug delivery system. The toxicological behavior of the system was studied in vivo in rats and mice. Acute and subchronic studies were carried out. Biochemical, hematological, and histopathological analysis was also done. There were no significant alterations in the biochemical parameters at a low dosage. There was a small change in alkaline phosphatase (ALP) level at a high dosage. The results indicate a safe toxicological profile. PMID:26491315

  20. Synthesis and surface active properties of cationic surface active agents from crude rice bran oil

    Directory of Open Access Journals (Sweden)

    El-Dougdoug, W. I. A.

    1999-10-01

    Full Text Available Cationic surfactants of 2-hidroxy-3-(2- alkylamidopolyethyl amino propane-1-triethylammonium hydroxides (ix-xuia-d were prepared from fatty acids (ia-d [palmitic, stearic, oleic, linoleic acid] and mixed fatty acids of crude rice bran oil ie [RBO]. The reaction of these acids with ethylenediamine, diethylenetriamine, triethylenetetramine andletraethylenepentamine (iia-d produced (iii-viia-d. The produced amidopolyethylamine (iii-viia-d reacted with 2-epoxypropylenetriethylammonium chloride (viii to give the cationic surfactants (ix-xiiia-d . The produced derivatives were purified and characterized by microanalysis, molecular weight determination, infra-red (IR, and proton nuclear magnetic resonance (1H NMR spectra. The surface active properties and inhibition efficiency of the prepared cationic surfactants were determined.

    Se han preparado tensioactivos catiónicos de hidróxidos de! 2-hidroxi-3-(2-alquilamidopolietilamino propano-1;trietilamonio (ix-xiiia-d a partir de los ácidos grasos (ia-d [ácido palmítico, esteárico, oleico y linoleico] y mezclas de ácidos grasos de aceite de germen de arroz crudo ie [RBO]. La reacción de estos ácidos con etilenodiamina, dietilenotriamina, trietilenotetramina y tetraetilenopentamina (iia-d produjo los compuestos (iv-viia-d . Los amidopolietilaminos producidos (iii-viia-d reaccionaron con el cloruro de 2-epoxipropilenotrietilamonio (viii para dar los tensioactivos catiónicos (ix-xiiia-d. Los derivados producidos se purificaron y caracterizaron por microanálisis, determinación del peso molecular, espectros de infrarrojo (IR y resonancia magnética nuclear de protón (1H NMR. Se determinaron las propiedades tensioactivas y la eficacia de inhibición de los tensioactivos cati

  1. A Modified Critical State Two-surface Plasticity Model for Sand

    DEFF Research Database (Denmark)

    Bakmar, Christian LeBlanc; Hededal, O.; Ibsen, Lars Bo

    This paper provides background information and documentation for the implementation of a robust plasticity model as a user-subroutine in the commercial finite difference code, FLAC3D by Itasca. The plasticity model presented is equal to the 3 dimensional critical state two-surface plasticity model...... for sands by Manzari et al., but uses a modified multi-axial surface formulation based on a versatile shape function prescribing a family of smooth and convex contours in the π-plane. The model is formulated within the framework of critical state soil mechanics and is capable of accurately simulating...

  2. XPS study of PBO fiber surface modified by incorporation of hydroxyl polar groups in main chains

    Energy Technology Data Exchange (ETDEWEB)

    Zhang Tao; Hu Dayong; Jin Junhong; Yang Shenglin [State Key Laboratory for Modification of Chemical Fibers and Polymer Materials, College of Material Science and Engineering, Donghua University, Shanghai 201620 (China); Li Guang, E-mail: lig@dhu.edu.cn [State Key Laboratory for Modification of Chemical Fibers and Polymer Materials, College of Material Science and Engineering, Donghua University, Shanghai 201620 (China); Jiang Jianming [State Key Laboratory for Modification of Chemical Fibers and Polymer Materials, College of Material Science and Engineering, Donghua University, Shanghai 201620 (China)

    2010-01-15

    Dihydroxy poly(p-phenylene benzobisoxazole) (DHPBO), a modified poly(p-phenylene benzoxazole) (PBO) polymer containing double hydroxyl groups in polymer chains, was synthesized by copolymerization of 4,6-diamino resorcinol dihydrochloride (DAR), purified terephthalic acid (TA) and 2,5-dihydroxyterephthalic acid (DHTA). DHPBO fibers were prepared by dry-jet wet-spinning method. The effects of hydroxyl polar groups on the surface elemental compositions of PBO fiber were investigated by X-ray photoelectron spectroscopy (XPS). The results show that the ratio of oxygen/carbon on the surface of DHPBO fibers is higher than that on the surface of PBO fibers, which indicates the content of polar groups on the surface of DHPBO fiber increase compared with PBO fiber.

  3. Titania nanotube arrays surface-modified with ZnO for enhanced photocatalytic applications

    Energy Technology Data Exchange (ETDEWEB)

    Nageri, Manoj; Kalarivalappil, Vijila; Vijayan, Baiju K.; Kumar, Viswanathan, E-mail: vkumar10@yahoo.co.in

    2016-05-15

    Highlights: • Heterostructures of TNA/ZnO synthesised through potentiostatic anodisation followed by hydrothermal method. • Evaluation of morphological features of the heterostructure with hydrothermal processing time. • Correlation of photocatalytic activity of the hetrostructure with its morphology and surface texture. - Abstract: Well ordered titanium dioxide nanotube arrays (TNA) of average diameter 129 nm and wall thickness of 25 nm were fabricated through potentiostatic anodisation of titanium (Ti) metal substrates. Such TNA were subsequently surface-modified with various amounts of zinc oxide (ZnO) nanopowders using hydrothermal technique to obtain heterogeneous TNA/ZnO nanostructures. The crystalline phase and surface microstructure of the heterostructures were determined by X-ray diffraction, Raman spectroscopy and scanning electron microscopy respectively. The morphology of the heterostructures strongly depended on the hydrothermal conditions employed. The photocatalytic activity of the heterostructures have also been investigated and correlated with their surface morphology and texture.

  4. Surface Properties of PAN-based Carbon Fibers Modified by Electrochemical Oxidization in Organic Electrolyte Systems

    Directory of Open Access Journals (Sweden)

    WU Bo

    2016-09-01

    Full Text Available PAN-based carbon fibers were modified by electrochemical oxidization using fatty alcohol polyoxyethylene ether phosphate (O3P, triethanolamine (TEOA and fatty alcohol polyoxyethylene ether ammonium phosphate (O3PNH4 as organic electrolyte respectively. Titration analysis, single fiber fracture strength measurement and field emission scanning electron microscopy (FE-SEM were used to evaluate the content of acidic functional group on the surface, mechanical properties and surface morphology of carbon fiber. The optimum process of electrochemical treatment obtained is at 50℃ for 2min and O3PNH4 (5%, mass fraction as the electrolyte with current density of 2A/g. In addition, the surface properties of modified carbon fibers were characterized by X-ray photoelectron spectroscopy (XPS and single fiber contact angle test. The results show that the hydrophilic acidic functional groups on the surface of carbon fiber which can enhance the surface energy are increased by the electrochemical oxidation using O3PNH4 as electrolyte, almost without any weakening to the mechanical properties of carbon fiber.

  5. Sol-gel network silica/modified montmorillonite clay hybrid nanocomposites for hydrophobic surface coatings.

    Science.gov (United States)

    Meera, Kamal Mohamed Seeni; Sankar, Rajavelu Murali; Murali, Adhigan; Jaisankar, Sellamuthu N; Mandal, Asit Baran

    2012-02-01

    Sol-gel silica/nanoclay composites were prepared through sol-gel polymerization technique using tetraethylorthosilicate precursor and montmorillonite (MMT) clay in aqueous media. In this study, both montmorillonite-K(+) and organically modified MMT (OMMT) clays were used. The prepared composites were coated on glass substrate by making 1 wt% solution in ethyltrichlorosilane. The incorporation of nanoclay does not alter the intensity of characteristic Si-O-Si peak of silica network. Thermogravimetric studies show that increasing clay content increased the degradation temperature of the composites. Differential scanning calorimetry (DSC) results of organically modified MMT nanoclay incorporated composite show a shift in the melting behavior up to 38°C. From DSC thermograms, we observed that the ΔH value decreased with increasing clay loading. X-ray diffraction patterns prove the presence of nanoclay in the composite and increase in the concentration of organically modified nanoclay from 3 to 5 wt% increases the intensity of the peak at 2θ=8° corresponds to OMMT. Morphology of the control silica gel composite was greatly influenced by the incorporation of OMMT. The presence of nanoclay changed the surface of control silica gel composite into cleaved surface with brittle in nature. Contact angle measurements were done for the coatings to study their surface behavior. These hybrid coatings on glass substrate may have applications for hydrophobic coatings on leather substrate. Copyright © 2011 Elsevier B.V. All rights reserved.

  6. Interaction between Palladium Nanoparticles and Surface-Modified Carbon Nanotubes: Role of Surface Functionalities

    DEFF Research Database (Denmark)

    Zhang, Bingsen; Shao, Lidong; Zhang, Wei

    2014-01-01

    degrees C. We focus on probing the effects of oxygen and nitrogen-containing functional groups on supported palladium nanoparticles (NPs) in the model catalytic system. The stability of palladium NPs supported on CNTs depends strongly on the surface properties of CNTs. Moreover, the oxygen...... feature, instability, and subtle response of the components upon application of an external field. Herein, we use insitu TEM, electron energy loss spectroscopy, and X-ray photoelectron spectroscopy techniques to record the interaction in palladium on carbon nanotubes (CNTs) from room temperature to 600...

  7. [Optimization of biocontrol agent Burkholderia pyrrocinia strain JK-SH007 fermentation by response surface methodology].

    Science.gov (United States)

    Li, Hao; Ren, Jiahong; Ye, Jianren

    2013-02-01

    In order to improve ferment efficiency of biocontrol agent Burkholderia pyrrocinia JK-SH007, the fermentation conditions of this strain were optimized. The optimal fermentation conditions were corn steep liquor (13.88 g/L) and glucose (3.37 g/L) by screening test, steepest ascent experiments and response surface analysis. The results showed that the cell density of JK-SH007 (1.18 x 10(9) CFU/mL) increased 1.35 times than before, and there was a 28.84% increase in antifungal activity.

  8. Intraoperative Evaluation of Body Surface Improvement by an Augmented Reality System That a Clinician Can Modify.

    Science.gov (United States)

    Mitsuno, Daisuke; Ueda, Koichi; Itamiya, Tomoki; Nuri, Takashi; Otsuki, Yuki

    2017-08-01

    Augmented reality (AR) technology that can combine computer-generated images with a real scene has been reported in the medical field recently. We devised the AR system for evaluation of improvements of the body surface, which is important for plastic surgery. We constructed an AR system that is easy to modify by combining existing devices and free software. We superimposed the 3-dimensional images of the body surface and the bone (obtained from VECTRA H1 and CT) onto the actual surgical field by Moverio BT-200 smart glasses and evaluated improvements of the body surface in 8 cases. In all cases, the 3D image was successfully projected on the surgical field. Improvement of the display method of the 3D image made it easier to distinguish the different shapes in the 3D image and surgical field, making comparison easier. In a patient with fibrous dysplasia, the symmetrized body surface image was useful for confirming improvement of the real body surface. In a patient with complex facial fracture, the simulated bone image was useful as a reference for reduction. In a patient with an osteoma of the forehead, simultaneously displayed images of the body surface and the bone made it easier to understand these positional relationships. This study confirmed that AR technology is helpful for evaluation of the body surface in several clinical applications. Our findings are not only useful for body surface evaluation but also for effective utilization of AR technology in the field of plastic surgery.

  9. Induced superhydrophobic and antimicrobial character of zinc metal modified ceramic wall tile surfaces

    Science.gov (United States)

    Özcan, Selçuk; Açıkbaş, Gökhan; Çalış Açıkbaş, Nurcan

    2018-04-01

    Hydrophobic surfaces are also known to have antimicrobial effect by restricting the adherence of microorganisms. However, ceramic products are produced by high temperature processes resulting in a hydrophilic surface. In this study, an industrial ceramic wall tile glaze composition was modified by the inclusion of metallic zinc powder in the glaze suspension applied on the pre-sintered wall tile bodies by spraying. The glazed tiles were gloss fired at industrially applicable peak temperatures ranging from 980 °C to 1100 °C. The fired tile surfaces were coated with a commercial fluoropolymer avoiding water absorption. The surfaces were characterized with SEM, EDS, XRD techniques, roughness, sessile water drop contact angle, surface energy measurements, and standard antimicrobial tests. The surface hydrophobicity and the antimicrobial activity results were compared with that of unmodified, uncoated gloss fired wall tiles. A superhydrophobic contact angle of 150° was achieved at 1000 °C peak temperature due to the formation of micro-structured nanocrystalline zinc oxide granules providing a specific surface topography. At higher peak temperatures the hydrophobicity was lost as the specific granular surface topography deteriorated with the conversion of zinc oxide granules to the ubiquitous willemite crystals embedded in the glassy matrix. The antimicrobial efficacy also correlated with the hydrophobic character.

  10. Surface Hardness of Dental Composite Resin Restorations in Response to Preventive Agents.

    Science.gov (United States)

    Al-Samadani, Khalid H

    2016-12-01

    To assess the impact of using preventive mouthwash agents on the surface hardness of various resins composites. Hundred specimens were prepared from five types of composite resin material in a Teflon mold. Five specimens from each type of restorative materials (Herculite XRV Ultra, Estelite Σ Quick, Z Hermack, Versa Comp Sultan, and Empress Direct IPS) were evaluated posttreatment with immersion in four types of preventive mouthwashes gels and rinses - group 1: Flocare gel (0.4% stannous fluoride), group 2: Pascal gel (topical APF fluoride), group 3: Pro-relief mouthwash (Na fluoride), and group 4: Plax Soin mouthwash (Na fluoride) - at 37°C in a dark glass container at 24, 48, and 72 hours. Surface hardness measurement was made for each tested material. Statistically, we analyzed the mean values with one-way analysis of variance (ANOVA) and Tukey's test, with significance level of p surface hardness with the time elapsed (24, 48, and 72 hours) postimmersion in the preventive mouthwashes and gels except the Herculite XRV Ultra and Versa Comp Sultan materials. Flocare gel group showed increase in the surface hardness after 48 hours of immersion than the other periods and in Estelite Σ Quick after 72 hours. There was significant differences in all materials tested with the immersion in the preventive mouthwashes and gels, such as Flocare gel (0.4% stannous fluoride), Pro-relief mouthwash (Na fluoride), and Plax Soin mouthwash (Na fluoride) except Pascal gel (topical APF fluoride) (p > 0.05), at time intervals mentioned earlier (p surface hardness with the time elapse of immersion for all materials except the Flocare gel group, which contains 0.4% stannous fluoride as a preventive ingredient increases the surface hardness after 48 h for Herculite XRV Ultra and Versa Comp Sultan and Estelite Σ Quick after 72 hours. The preventive agents in the form of mouthwash and gel are used to prevent oral diseases that affect the surface hardness of composite resin, and this

  11. Some Surface-Active Agents and Their Virucidal Effect on Foot-and-Mouth Disease Virus

    Science.gov (United States)

    Fellowes, O. N.

    1965-01-01

    Selected cationic and anionic surface-active compounds were tested to determine their virucidal effect on the foot-and-mouth disease virus, type O, strain M11, propagated in primary calf kidney cells. The chemical inactivation of the virus was tested with 0.5, 1.0, 2.0, and 5.0% concentrations of the selected compounds. Virus controls with pH adjusted to cover the expected range of the mixtures of the chemicals and virus were also tested. The absence of virus from the mixtures of chemical and virus after reaction at 28 C for 2 hr was assayed by inoculating suckling mice with the mixtures. One cationic compound, alkyl methyl isoquinilinium chloride, showed considerable antiviral activity due largely to pH effect. The use of the surface-active agents investigated in this study, in the presence of organic material, would not be recommended as virucides. PMID:4286396

  12. Antibacterial and microstructure properties of titanium surfaces modified with Ag-incorporated nanotube arrays

    Energy Technology Data Exchange (ETDEWEB)

    Li, Guangzhong; Cheng, Li [State Key Laboratory of Porous Metal Materials, Northwest Institute for Nonferrous Metal Research (China); Yang, Hui-lin [Department of Orthopaedics, Wuxi People' s Hospital, Nanjing Medical University, Jiangsu Province (China); Zhao, Quan-ming, E-mail: abc8385@163.com [Department of Orthopaedics, The First Affiliated Hospital of Soochow University, Suzhou (China)

    2016-07-15

    Although titanium (Ti) and its alloys have been widely used as implants in clinical settings, failures still occur mainly due to poor bioactivity and implant-associated infections. Here, we coated Ti implants with TiO{sub 2} nanotubes (TNTs) incorporated with the antibacterial agent Ag to produce Ag-TNTs, through anodization in AgNO{sub 3} and xenon light irradiation. We characterized surface morphology and composition of the coating with scanning electron microscopy (SEM) and X-ray diffraction (XRD), respectively. We investigated surface topography of the coatings by atomic force microscopy (AFM) operated in the tapping mode. The results indicate that Ag was successfully doped onto the TNTs, and that the nanoparticles were mainly distributed on the surface of TNTs. Finally, our antibacterial experiments reveal that Ag-TNTs on Ti implants exhibit excellent antibacterial activities, which promises to have significant clinical applications as implants. (author)

  13. Cotton textiles modified with citric acid as efficient anti-bacterial agent for prevention of nosocomial infections

    Science.gov (United States)

    Bischof Vukušić, Sandra; Flinčec Grgac, Sandra; Budimir, Ana; Kalenić, Smilja

    2011-01-01

    Aim To study the antimicrobial activity of citric acid (CA) and sodium hypophosphite monohydrate (SHP) against gram-positive and gram-negative bacteria, and to determine the influence of conventional and microwave thermal treatments on the effectiveness of antimicrobial treatment of cotton textiles. Method Textile material was impregnated with CA and SHP solution and thermally treated by either conventional or microwave drying/curing treatment. Antibacterial effectiveness was tested according to the ISO 20743:2009 standard, using absorption method. The surfaces were morphologically observed by scanning electron microscopy, while physical characteristics were determined by wrinkle recovery angles method (DIN 53 891), tensile strength (DIN 53 837), and whiteness degree method (AATCC 110-2000). Results Cotton fabric treated with CA and SHP showed significant antibacterial activity against MRSA (6.38 log10 treated by conventional drying and 6.46 log10 treated by microwave drying before washing, and 6.90 log10 and 7.86 log10, respectively, after 1 cycle of home domestic laundering washing [HDLW]). Antibacterial activity was also remarkable against S. aureus (4.25 log10 by conventional drying, 4.58 log10 by microwave drying) and against P. aeruginosa (1.93 log10 by conventional and 4.66 log10 by microwave drying). Antibacterial activity against P. aeruginosa was higher in samples subjected to microwave drying/curing than in those subjected to conventional drying/curing. As expected, antibacterial activity was reduced after 10 HDLW cycles but the compound was still effective. The surface of the untreated cotton polymer was smooth, while minor erosion stripes appeared on the surfaces treated with antimicrobial agent, and long and deep stripes were found on the surface of the washed sample. Conclusion CA can be used both for the disposable (non-durable) materials (gowns, masks, and cuffs for blood pressure measurement) and the materials that require durability to laundering

  14. Thermally controlled growth of surface nanostructures on ion-modified AIII-BV semiconductor crystals

    Science.gov (United States)

    Trynkiewicz, Elzbieta; Jany, Benedykt R.; Wrana, Dominik; Krok, Franciszek

    2018-01-01

    The primary motivation for our systematic study is to provide a comprehensive overview of the role of sample temperature on the pattern evolution of several AIII-BV semiconductor crystal (001) surfaces (i.e., InSb, InP, InAs, GaSb) in terms of their response to low-energy Ar+ ion irradiation conditions. The surface morphology and the chemical diversity of such ion-modified binary materials has been characterized by means of scanning electron microscopy (SEM). In general, all surface textures following ion irradiation exhibit transitional behavior from small islands, via vertically oriented 3D nanostructures, to smoothened surface when the sample temperature is increased. This result reinforces our conviction that the mass redistribution of adatoms along the surface plays a vital role during the formation and growth process of surface nanostructures. We would like to emphasize that this paper addresses in detail for the first time the topic of the growth kinetics of the nanostructures with regard to thermal surface diffusion, while simultaneously offering some possible approaches to supplementing previous studies and therein gaining a new insight into this complex issue. The experimental results are discussed with reference to models of the pillars growth, abutting on preferential sputtering, the self-sustained etch masking effect and the redeposition process recently proposed to elucidate the observed nanostructuring mechanism.

  15. Methodology for calculating the volume of condensate droplets on topographically modified, microgrooved surfaces.

    Science.gov (United States)

    Sommers, A D

    2011-05-03

    Liquid droplets on micropatterned surfaces consisting of parallel grooves tens of micrometers in width and depth are considered, and a method for calculating the droplet volume on these surfaces is presented. This model, which utilizes the elongated and parallel-sided nature of droplets condensed on these microgrooved surfaces, requires inputs from two droplet images at ϕ = 0° and ϕ = 90°--namely, the droplet major axis, minor axis, height, and two contact angles. In this method, a circular cross-sectional area is extruded the length of the droplet where the chord of the extruded circle is fixed by the width of the droplet. The maximum apparent contact angle is assumed to occur along the side of the droplet because of the surface energy barrier to wetting imposed by the grooves--a behavior that was observed experimentally. When applied to water droplets condensed onto a microgrooved aluminum surface, this method was shown to calculate the actual droplet volume to within 10% for 88% of the droplets analyzed. This method is useful for estimating the volume of retained droplets on topographically modified, anisotropic surfaces where both heat and mass transfer occur and the surface microchannels are aligned parallel to gravity to assist in condensate drainage.

  16. Optical properties study of silicone polymer PDMS substrate surfaces modified by plasma treatment

    Science.gov (United States)

    Zahid, A.; Dai, B.; Hong, R.; Zhang, D.

    2017-10-01

    In this study, PDMS (polydimethylsiloxane) substrates with a half-plain, half-rough surface were prepared on a plain and rough fused silica glass substrate using a molding technique. The molded PDMS surface morphology was changed into a half-smooth and half-rough surface after peeling. The modified PDMS surfaces’ optical properties were inspected with and without treatment. The treatment is exposed by oxygen plasma (15 W) for 3 min in a vacuum, down to a pressure of six torr, using a vacuum pump. An atomic force microscope (AMF) and interferometer (white light) indicated that the plasma O2 treatment increased the formation of the plain surface and decreased the formation of the rough surface. The optical properties via a spectrophotometer (lambda) show the resonance from 300 nm to 1200 nm on the rough surface, which is considered to be a faithful reproduction for transmittance and reflectance. The Raman spectra and FDTD simulation results are in excellent agreement; not to be confused with metal local surface plasmon resonances (LSPRs). The Raman spectra peaks and hotspot are the results of the PDMS Si-O backbone. The PDMS substrate presented the diversity of the optical properties, which makes the substrate complementary to various optical applications.

  17. Surface-modified polymeric pads for enhanced performance during chemical mechanical planarization

    International Nuclear Information System (INIS)

    Deshpande, S.; Dakshinamurthy, S.; Kuiry, S.C.; Vaidyanathan, R.; Obeng, Y.S.; Seal, S.

    2005-01-01

    The chemical mechanical planarization (CMP) process occurs at an atomic level at the slurry/wafer interface and hence slurries and polishing pads play a critical role in their successful implementation. Polyurethane is a commonly used polymer in the manufacturing of CMP pads. These pads are incompatible with some chemicals present in the CMP slurries, such as hydrogen peroxide. To overcome these problems, Psiloquest has developed new Application Specific Pads (ASP). Surface of such pads has been modified by depositing a thin film of tetraethyl orthosilicate using plasma-enhanced chemical vapor deposition (PECVD) process. In the present study, mechanical properties of such coated pads have been investigated using nanoindentation. The surface morphology and the chemistry of the ASP were studied using scanning electron microcopy, X-ray photoelectron spectroscopy, and Fourier transform infrared spectroscopy techniques. It was observed that mechanical and chemical properties of the pad top surface are a function of the PECVD coating time. Such PECVD-treated pads are found to be hydrophilic and do not require storage in aqueous media during the not-in-use period. The metal removal rate using such surface-modified polishing pads was found to increase linearly with the PECVD coating time

  18. Decreased fibrous encapsulation and enhanced osseointegration in vitro by decorin-modified titanium surface.

    Science.gov (United States)

    He, Ronghan; Lu, Yunxiang; Ren, Jianhua; Wang, Zhe; Huang, Junqi; Zhu, Lei; Wang, Kun

    2017-07-01

    Orthopedic implants, using materials such as titanium, are extensively used in clinical surgeries. Despite its popularity, titanium is still inadequate to reliable osseointegration due to aseptic loosing. Fibrous encapsulation on the titanium implant interface prevents osseointegration and leads to the loosing of orthopedic implant. In this study, decorin was loaded on titanium surface by polydopamine film to examine fibrous encapsulation inhibition and bone growth acceleration. The coating of decorin was evaluated by X-ray photoelectron spectroscopy (XPS) and fluorescence microscopy. Quantitative analysis showed increased decorin coating on titanium surface when decorin in the loading solution increases. To test the effect of decorin modification, fibroblast and osteoblast cultures were utilized in vitro. The results showed that the functions of fibroblasts (proliferation, migration and collagen synthesis) were significantly attenuated on the decorin-modified surfaces and this anti-fibrous effect could be due to fibrotic gene suppression by decorin. In contrast, osteoblastic activities, such as calcium deposition and alkaline phosphatase (ALP) activity, were enhanced by the modified decorin. These results suggest that decorin coating on titanium surface inhibited proliferation and function of fibroblasts and improved that of osteoblasts. Therefore, this study is potentially useful for enhancing orthopedic implant. Copyright © 2017 Elsevier B.V. All rights reserved.

  19. Modified SIMPLE algorithm for the numerical analysis of incompressible flows with free surface

    International Nuclear Information System (INIS)

    Mok, Jin Ho; Hong, Chun Pyo; Lee, Jin Ho

    2005-01-01

    While the SIMPLE algorithm is most widely used for the simulations of flow phenomena that take place in the industrial equipment or the manufacturing processes, it is less adopted for the simulations of the free surface flow. Though the SIMPLE algorithm is free from the limitation of time step, the free surface behavior imposes the restriction on the time step. As a result, the explicit schemes are faster than the implicit scheme in terms of computation time when the same time step is applied to, since the implicit scheme includes the numerical method to solve the simultaneous equations in its procedure. If the computation time of SIMPLE algorithm can be reduced when it is applied to the unsteady free surface flow problems, the calculation can be carried out in the more stable way and, in the design process, the process variables can be controlled based on the more accurate data base. In this study, a modified SIMPLE algorithm is presented for the free surface flow. The broken water column problem is adopted for the validation of the modified algorithm (MoSIMPLE) and for comparison to the conventional SIMPLE algorithm

  20. Surface Decontamination of Chemical Agent Surrogates Using an Atmospheric Pressure Air Flow Plasma Jet

    Science.gov (United States)

    Li, Zhanguo; Li, Ying; Cao, Peng; Zhao, Hongjie

    2013-07-01

    An atmospheric pressure dielectric barrier discharge (DBD) plasma jet generator using air flow as the feedstock gas was applied to decontaminate the chemical agent surrogates on the surface of aluminum, stainless steel or iron plate painted with alkyd or PVC. The experimental results of material decontamination show that the residual chemical agent on the material is lower than the permissible value of the National Military Standard of China. In order to test the corrosion effect of the plasma jet on different material surfaces in the decontamination process, corrosion tests for the materials of polymethyl methacrylate, neoprene, polyvinyl chloride (PVC), polyethylene (PE), phenolic resin, iron plate painted with alkyd, stainless steel, aluminum, etc. were carried out, and relevant parameters were examined, including etiolation index, chromatism, loss of gloss, corrosion form, etc. The results show that the plasma jet is slightly corrosive for part of the materials, but their performances are not affected. A portable calculator, computer display, mainboard, circuit board of radiogram, and a hygrometer could work normally after being treated by the plasma jet.

  1. Surface Decontamination of Chemical Agent Surrogates Using an Atmospheric Pressure Air Flow Plasma Jet

    International Nuclear Information System (INIS)

    Li Zhanguo; Li Ying; Cao Peng; Zhao Hongjie

    2013-01-01

    An atmospheric pressure dielectric barrier discharge (DBD) plasma jet generator using air flow as the feedstock gas was applied to decontaminate the chemical agent surrogates on the surface of aluminum, stainless steel or iron plate painted with alkyd or PVC. The experimental results of material decontamination show that the residual chemical agent on the material is lower than the permissible value of the National Military Standard of China. In order to test the corrosion effect of the plasma jet on different material surfaces in the decontamination process, corrosion tests for the materials of polymethyl methacrylate, neoprene, polyvinyl chloride (PVC), polyethylene (PE), phenolic resin, iron plate painted with alkyd, stainless steel, aluminum, etc. were carried out, and relevant parameters were examined, including etiolation index, chromatism, loss of gloss, corrosion form, etc. The results show that the plasma jet is slightly corrosive for part of the materials, but their performances are not affected. A portable calculator, computer display, mainboard, circuit board of radiogram, and a hygrometer could work normally after being treated by the plasma jet

  2. Inactivation of bacterial and viral biothreat agents on metallic copper surfaces.

    Science.gov (United States)

    Bleichert, Pauline; Espírito Santo, Christophe; Hanczaruk, Matthias; Meyer, Hermann; Grass, Gregor

    2014-12-01

    In recent years several studies in laboratory settings and in hospital environments have demonstrated that surfaces of massive metallic copper have intrinsic antibacterial and antiviral properties. Microbes are rapidly inactivated by a quick, sharp shock known as contact killing. The underlying mechanism is not yet fully understood; however, in this process the cytoplasmic membrane is severely damaged. Pathogenic bacterial and viral high-consequence species able to evade the host immune system are among the most serious lethal microbial challenges to human health. Here, we investigated contact-killing mediated by copper surfaces of Gram-negative bacteria (Brucella melitensis, Burkholderia mallei, Burkholderia pseudomallei, Francisella tularensis tularensis and Yersinia pestis) and of Gram-positive endospore-forming Bacillus anthracis. Additionally, we also tested inactivation of monkeypox virus and vaccinia virus on copper. This group of pathogens comprises biothreat species (or their close relatives) classified by the Center for Disease and Control and Prevention (CDC) as microbial select agents posing severe threats to public health and having the potential to be deliberately released. All agents were rapidly inactivated on copper between 30 s and 5 min with the exception of B. anthracis endospores. For vegetative bacterial cells prolonged contact to metallic copper resulted in the destruction of cell structure.

  3. Synthesis of nano-hydroxyapatite and its rapid mediated surface functionalization by silane coupling agent.

    Science.gov (United States)

    Rehman, Sarish; Khan, Kishwar; Mujahid, Mohammad; Nosheen, Shaneela

    2016-01-01

    In this work, hydroxyapatite (HA) nanorods were synthesized by simple one step wet precipitation method followed by their rapid surface functionalization via aminopropyltriethoxysilane (APTS) to give modified (HA-APTS) product. Functionalized hydroxyapatite (HA-APTS) holds amino groups on their surface that can be further functionalized with other bioactive molecules. The extent of functionalization of HA was studied under three different processing conditions; at room temperature, at 80 °C and under microwave condition (600 W). Three different temperatures have been use for the purpose of comparison between the functionalized products so that we can judge that whether there is any effect of temperature on the final products. In the last we conclude that temperature has no effect. So microwave condition is best to carried out the functionalization in just 5 min. Copyright © 2015 Elsevier B.V. All rights reserved.

  4. On the PEEK composites reinforced by surface-modified nano-silica

    International Nuclear Information System (INIS)

    Lai, Y.H.; Kuo, M.C.; Huang, J.C.; Chen, M.

    2007-01-01

    The nano-sized silica fillers reinforced poly(ether ether ketone) (PEEK) composites were fabricated by means of compression molding technique. The nano-sized silica, measuring 30 nm in size, was firstly modified by surface pretreatment with stearic acid. The performances and properties of the resulting PEEK/SiO 2 nanocomposites were examined in terms of tensile loading, hardness, dynamic mechanical analysis (DMA), thermomechanical analysis (TMA), thermogravimetry analysis (TGA), differential scanning calorimetry (DSC), X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The modified nano-silica was seen to disperse more uniformly than the unmodified counterpart. The XRD patterns of the modified silica reinforced PEEK composites reveal a systematic shift toward higher angles, suggesting the smaller d-spacing of the PEEK crystallites. The coefficient of thermal expansion (CTE) becomes lowered when the content of the nano-silica increases. Furthermore, the CTE of the modified silica filled PEEK nanocomposites shows the higher CTE values. A logic model is proposed. The increment of the dynamic modulus for the PEEK nanocomposites is up to 40% at elevated temperatures from 100 to 250 deg. C, indicating the apparent improvement of elevated temperature mechanical properties

  5. Corrosion resistance of the AISI 304, 316 and 321 stainless steel surfaces modified by laser

    Science.gov (United States)

    Szubzda, B.; Antończak, A.; Kozioł, P.; Łazarek, Ł.; Stępak, B.; Łęcka, K.; Szmaja, A.; Ozimek, M.

    2016-02-01

    The article presents the analysis results of the influence of laser fluence on physical and chemical structure and corrosion resistance of stainless steel surfaces modified by irradiating with nanosecond-pulsed laser. The study was carried out for AISI 304, AISI 316 and AISI 321 substrates using Yb:glass fiber laser. All measurements were made for samples irradiated in a broad range of accumulated fluence (10÷400 J/cm2). The electrochemical composition (by EDX) and surface morphology (by SEM) of the prepared surfaces were carried out. Finally, corrosion resistance was analyzed by a potentiodynamic electrochemical test. The obtained results showed very high corrosion resistance for samples made by fluency of values lower than 100 J/cm2. In this case, higher values of corrosion potentials and breakdown potentials were observed. A correlation between corrosion phenomena, the range of laser power (fluence) and the results of chemical and structural tests were also found.

  6. Observation of modified radiative properties of cold atoms in vacuum near a dielectric surface

    International Nuclear Information System (INIS)

    Ivanov, V V; Cornelussen, R A; Heuvell, H B van Linden van den; Spreeuw, R J C

    2004-01-01

    We have observed a distance-dependent absorption linewidth of cold 87 Rb atoms close to a dielectric-vacuum interface. This is the first observation of modified radiative properties in vacuum near a dielectric surface. A cloud of cold atoms was created using a magneto-optical trap (MOT) and optical molasses cooling. Evanescent waves (EW) were used to observe the behaviour of the atoms near the surface. We observed an increase of the absorption linewidth by up to 25% with respect to the free-space value. Approximately half the broadening can be explained by cavity quantum electrodynamics (CQED) as an increase of the natural linewidth and inhomogeneous broadening. The remainder we attribute to local Stark shifts near the surface. By varying the characteristic EW length we have observed a distance dependence characteristic for CQED

  7. Surface-modified yeast cells: A novel eukaryotic carrier for oral application.

    Science.gov (United States)

    Kenngott, Elisabeth E; Kiefer, Ruth; Schneider-Daum, Nicole; Hamann, Alf; Schneider, Marc; Schmitt, Manfred J; Breinig, Frank

    2016-02-28

    The effective targeting and subsequent binding of particulate carriers to M cells in Peyer's patches of the gut is a prerequisite for the development of oral delivery systems. We have established a novel carrier system based on cell surface expression of the β1-integrin binding domain of invasins derived from Yersinia enterocolitica and Yersinia pseudotuberculosis on the yeast Saccharomyces cerevisiae. All invasin derivatives were shown to be effectively expressed on the cell surface and recombinant yeast cells showed improved binding to both human HEp-2 cells and M-like cells in vitro. Among the different derivatives tested, the integrin-binding domain of Y. enterocolitica invasin proved to be the most effective and was able to target Peyer's patches in vivo. In conclusion, cell surface-modified yeasts might provide a novel bioadhesive, eukaryotic carrier system for efficient and targeted delivery of either antigens or drugs via the oral route. Copyright © 2015 Elsevier B.V. All rights reserved.

  8. Polydopamine/Cysteine surface modified isoporous membranes with self-cleaning properties

    KAUST Repository

    Shevate, Rahul

    2017-02-03

    The major challenge in membrane filtration is fouling which reduces the membrane performance. Fouling is mainly due to the adhesion of foulants on the membrane surfaces. In this work, we studied the fouling behaviour of polystyrene-b-poly(4-vinylpyridine) (PS-b-P4VP) isoporous membrane and the mussel inspired polydopamine/L-cysteine isoporous zwitterionic membrane. Polystyrene-b-poly(4-vinylpyridine) (PS-b-P4VP) isoporous membranes were fabricated via self-assembly and non-solvent induced phase separation method. Subsequently, the isoporous membrane was modified by a mild mussel-inspired polydopamine (PDA) coating; the isoporous surface structure and the water flux was retained. Zwitterionic L-cysteine was further anchored on the PDA coated membranes via Michael addition reaction at pH 7 and 50 °C to alleviate their antifouling ability with foulants solution. The membranes were thoroughly characterized using X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), atomic force microscopy (AFM) and zeta potential measurements. Contact angle and dynamic scanning calorimetry (DSC) measurements were carried out to examine the hydrophilicity. The pH-responsive behaviour of the modified membrane remains unchanged and antifouling ability after PDA/L-cysteine functionalization was improved. The modified and unmodified isoporous membranes were tested using humic acid and natural organic matter model solutions at 0.5 bar feed pressure.

  9. Aflatoxin Toxicity Reduction in Feed by Enhanced Binding to Surface-Modified Clay Additives

    Science.gov (United States)

    Jaynes, William F.; Zartman, Richard E.

    2011-01-01

    Animal feeding studies have demonstrated that clay additives, such as bentonites, can bind aflatoxins in ingested feed and reduce or eliminate the toxicity. Bentonite deposits are found throughout the world and mostly consist of expandable smectite minerals, such as montmorillonite. The surfaces of smectite minerals can be treated with organic compounds to create surface-modified clays that more readily bind some contaminants than the untreated clay. Montmorillonites treated with organic cations, such as hexadecyltrimethylammonium (HDTMA) and phenyltrimethylammonium (PTMA), more effectively remove organic contaminants, such as benzene and toluene, from water than untreated clay. Similarly, montmorillonite treated with PTMA (Kd = 24,100) retained more aflatoxin B1 (AfB1) from aqueous corn flour than untreated montmorillonite (Kd = 944). Feed additives that reduced aflatoxin toxicity in animal feeding studies adsorbed more AfB1 from aqueous corn flour than feed additives that were less effective. The organic cations HDTMA and PTMA are considered toxic and would not be suitable for clay additives used in feed or food, but other non-toxic or nutrient compounds can be used to prepare surface-modified clays. Montmorillonite (SWy) treated with choline (Kd = 13,800) and carnitine (Kd = 3960) adsorbed much more AfB1 from aqueous corn flour than the untreated clay (Kd = 944). A choline-treated clay prepared from a reduced-charge, high-charge montmorillonite (Kd = 20,100) adsorbed more AfB1 than the choline-treated high-charge montmorillonite (Kd = 1340) or the untreated montmorillonite (Kd = 293). Surface-modified clay additives prepared using low-charge smectites and nutrient or non-toxic organic compounds might be used to more effectively bind aflatoxins in contaminated feed or food and prevent toxicity. PMID:22069725

  10. Effect of Surface Modification by Chelating Agents on Fischer- Tropsch Performance of Co/SiO{sub 2} Catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Bambal, Ashish S.; Kugler, Edwin L.; Gardner, Todd H.; Dadyburjor, Dady B.

    2013-11-14

    The silica support of a Co-based catalyst for Fischer-Tropsch (FT) synthesis was modified by the chelating agents (CAs) nitrilotriacetic acid (NTA) and ethylenediaminetetraacetic acid (EDTA). After the modification, characterization of the fresh and spent catalysts show reduced crystallite sizes, a better-dispersed Co₃O₄ phase on the calcined samples, and increased metal dispersions for the reduced samples. The CA-modified catalysts display higher CO conversions, product yields, reaction rates and rate constants. The improved FT performance of CA-modified catalysts is attributed to the formation of stable complexes with Co. The superior performance of the EDTA-modified catalyst in comparison to the NTA-modified catalyst is due to the higher affinity of the former for complex formation with Co ions.

  11. Explaining electrostatic charging and flow of surface-modified acetaminophen powders as a function of relative humidity through surface energetics.

    Science.gov (United States)

    Jallo, Laila J; Dave, Rajesh N

    2015-07-01

    Powder flow involves particle-particle and particle-vessel contacts and separation resulting in electrostatic charging. This important phenomenon was studied for uncoated and dry-coated micronized acetaminophen (MAPAP) as a function of relative humidity. The main hypothesis is that by modifying powder surface energy via dry coating of MAPAP performed using magnetically assisted impaction coating, its charging tendency, flow can be controlled. The examination of the relationship between electrostatic charging, powder flow, and the surface energies of the powders revealed that an improvement in flow because of dry coating corresponded to a decrease in the charging of the particles. A general trend of reduction in both electrostatic charging and dispersive surface energy with dry coating and relative humidity were also observed, except that a divergent behavior was observed at higher relative humidities (≥55% RH). The uncoated powder was found to have strong electron acceptor characteristic as compared with the dry coated. The adhesion energy between the particles and the tubes used for the electrostatic charging qualitatively predicted the decreasing trend in electrostatic charging from plastic tubes to stainless steel. In summary, the surface energies of the powders and the vessel could explain the electrostatic charging behavior and charge reduction because of dry coating. © 2015 Wiley Periodicals, Inc. and the American Pharmacists Association.

  12. Study on the structure-properties relationship of natural rubber/SiO2 composites modified by a novel multi-functional rubber agent

    Directory of Open Access Journals (Sweden)

    S. Y. Yang

    2014-06-01

    Full Text Available Vulcanization property and structure-properties relationship of natural rubber (NR/silica (SiO2 composites modified by a novel multi-functional rubber agent, N-phenyl- N'-(γ-triethoxysilane-propyl thiourea (STU, are investigated in detail. Results from the infrared spectroscopy (IR and X-ray photoelectron spectroscopy (XPS show that STU can graft to the surface of SiO2 under heating, resulting in a fine-dispersed structure in the rubber matrix without the connectivity of SiO2 particles as revealed by transmission electron microscopy (TEM. This modification effect reduces the block vulcanization effect of SiO2 for NR/SiO2/STU compounds under vulcanization process evidently. The 400% modulus and tensile strength of NR/SiO2/STU composites are much higher than that of NR/SiO2/TU composites, although the crystal index at the stretching ratio of 4 and crosslinking densities of NR/SiO2 composites are almost the same at the same dosage of SiO2. Consequently, a structure-property relationship of NR/SiO2/STU composites is proposed that the silane chain of STU can entangle with NR molecular chains to form an interfacial region, which is in accordance with the experimental observations quite well.

  13. Surface decontamination for blister agents Lewisite, sulfur mustard and agent yellow, a Lewisite and sulfur mustard mixture.

    Science.gov (United States)

    Stone, Harry; See, David; Smiley, Autumn; Ellingson, Anthony; Schimmoeller, Jessica; Oudejans, Lukas

    2016-08-15

    Sulfur mustard (HD) and Lewisite (L) are blister agents that have a high potential for terrorist use; Agent Yellow (HL) is the eutectic mixture of HD and L. Bench-scale testing was used to determine the residual amount of these chemical warfare agents remaining on three building materials (wood, metal and glass) after application of various decontaminants (household bleach, full strength and dilute; hydrogen peroxide 3% solution; and EasyDECON(®) DF200). All decontaminants reduced the amount of L recovered from coupons. Application of dilute bleach showed little or no difference compared to natural attenuation in the amount of HD recovered from coupons. Full-strength bleach was the most effective of four decontaminants at reducing the amount of HD from coupons. Hydrogen peroxide (3% solution) and DF200 did decrease the amount of HD recovered from coupons more than natural attenuation (except DF200 against HD on metal), but substantial amounts of HD remained on some materials. Toxic HD by-products were generated by hydrogen peroxide treatment. The effectiveness of decontaminants was found to depend on agent, material, and decontaminant. Increased decontaminant reaction time (60min rather than 30min) did not significantly increase effectiveness. Published by Elsevier B.V.

  14. Protein arrangement on modified diamond-like carbon surfaces - An ARXPS study

    Science.gov (United States)

    Oosterbeek, Reece N.; Seal, Christopher K.; Hyland, Margaret M.

    2014-12-01

    Understanding the nature of the interface between a biomaterial implant and the biological fluid is an essential step towards creating improved implant materials. This study examined a diamond-like carbon coating biomaterial, the surface energy of which was modified by Ar+ ion sputtering and laser graphitisation. The arrangement of proteins was analysed by angle resolved X-ray photoelectron spectroscopy, and the effects of the polar component of surface energy on this arrangement were observed. It was seen that polar groups (such as CN, CO) are more attracted to the coating surface due to the stronger polar interactions. This results in a segregation of these groups to the DLC-protein interface; at increasing takeoff angle (further from to DLC-protein interface) fewer of these polar groups are seen. Correspondingly, groups that interact mainly by dispersive forces (CC, CH) were found to increase in intensity as takeoff angle increased, indicating they are segregated away from the DLC-protein interface. The magnitude of the segregation was seen to increase with increasing polar surface energy, this was attributed to an increased net attraction between the solid surface and polar groups at higher polar surface energy (γSp).

  15. A probabilistic approach to measure the strength of bone cell adhesion to chemically modified surfaces.

    Science.gov (United States)

    Rezania, A; Thomas, C H; Healy, K E

    1997-01-01

    Patterned surfaces with alternating regions of amino silanes [N-(2-aminoethyl)-3-aminopropyl-trimethoxysilane (EDS)] and alkyl silanes [dimethyldichlorosilane (DMS)] have been used to alter the kinetics of spatial distribution of cells in vitro. In particular, we have previously observed the preferential spatial distribution of bone cells on the EDS regions of EDS/ DMS patterned surfaces (10). In this study, we examined whether the mechanism of spatial distribution of cells on the EDS regions was adhesion mediated. Homogeneous layers of EDS and DMS were immobilized on quartz substrates and characterized by contact angle. X-ray photoelectron spectroscopy, and spectroscopic ellipsometry. The strength of bone cell attachment to the modified substrates was examined using a radial flow apparatus, within either 20 min or 2 hr of cell incubation in the presence of serum. A Weibull distribution was chosen to characterize the strength of cell-substratum adhesion. Within 20 min of cell exposure, the strength of adhesion was significantly larger on EDS and clean surfaces, compared with DMS surfaces (p < 0.001). Within 2 hr of cell incubation, there was no statistical difference between the strength of cell adhesion to EDS, DMS, and clean surfaces. The results of this study suggest that the surface chemistry mediates adhesion-based spatial cell arrangement through a layer of adsorbed serum proteins.

  16. Improvement of in vitro corrosion and cytocompatibility of biodegradable Fe surface modified by Zn ion implantation

    Science.gov (United States)

    Wang, Henan; Zheng, Yang; Li, Yan; Jiang, Chengbao

    2017-05-01

    Pure Fe was surface-modified by Zn ion implantation to improve the biodegradable behavior and cytocompatibility. Surface topography, chemical composition, corrosion resistance and cytocompatibility were investigated. Atomic force microscopy, auger electron spectroscopy and X-ray photoelectron spectroscopy results showed that Zn was implanted into the surface of pure Fe in the depth of 40-60 nm and Fe2O3/ZnO oxides were formed on the outmost surface. Electrochemical measurements and immersion tests revealed an improved degradable behavior for the Zn-implanted Fe samples. An approximately 12% reduction in the corrosion potential (Ecorr) and a 10-fold increase in the corrosion current density (icorr) were obtained after Zn ion implantation with a moderate incident ion dose, which was attributed to the enhanced pitting corrosion. The surface free energy of pure Fe was decreased by Zn ion implantation. The results of direct cell culture indicated that the short-term (4 h) cytocompatibility of MC3T3-E1 cells was promoted by the implanted Zn on the surface.

  17. Corrosive characteristics of surface-modified stainless steel bipolar plate in solid polymer fuel cell

    Science.gov (United States)

    Zhang, Xiaowen; Wang, Lixia; Sun, Juncai

    2015-03-01

    In this paper, corrosion behavior of an AISI 304 stainless steel modified by niobium or niobium nitride (denoted as niobized 304 SS and Nb-N 304 SS, respectively) is investigated in simulated solid polymer fuel cell (SPFC) operating conditions. Potentiodynamic polarizations show that the corrosion potentials of surface modified 304 SS shift to positive direction while the corrosion current densities decrease greatly comparing with the bare 304 SS in simulated anodic SPFC environments. The order of corrosive resistance in corrosive potential, corrosive current density and pitting potential is: Nb-N 304 SS > niobized 304 SS > bare 304 SS. In the methanol-fueled SPFC operating conditions, the results show that the corrosion resistance of bare and niobized 304 SS increases with the methanol concentration increasing in the test solutions.

  18. Surface Photochemistry: Benzophenone as a Probe for the Study of Modified Cellulose Fibres

    Directory of Open Access Journals (Sweden)

    L. F. Vieira Ferreira

    2007-01-01

    Full Text Available This work reports the use of benzophenone, a very well characterized probe, to study new hosts (i.e., modified celluloses grafted with alkyl chains bearing 12 carbon atoms by surface esterification. Laser-induced room temperature luminescence of air-equilibrated or argon-purged solid powdered samples of benzophenone adsorbed onto the two modified celluloses, which will be named C12-1500 and C12-1700, revealed the existence of a vibrationally structured phosphorescence emission of benzophenone in the case where ethanol was used for sample preparation, while a nonstructured emission of benzophenone exists when water was used instead of ethanol. The decay times of the benzophenone emission vary greatly with the solvent used for sample preparation and do not change with the alkylation degree in the range of 1500–1700 micromoles of alkyl chains per gram of cellulose. When water was used as a solvent for sample preparation, the shortest lifetime for the benzophenone emission was observed; this result is similar to the case of benzophenone adsorbed onto the “normal” microcrystalline cellulose surface, with this latter case previously reported by Vieira Ferreira et al. in 1995. This is due to the more efficient hydrogen abstraction reaction from the glycoside rings of cellulose when compared with hydrogen abstraction from the alkyl chains of the modified celluloses. Triplet-triplet transient absorption of benzophenone was obtained in both cases and is the predominant absorption immediately after laser pulse, while benzophenone ketyl radical formation occurs in a microsecond time scale both for normal and modified celluloses.

  19. Surface pH of resin-modified glass polyalkenoate (ionomer) cements.

    Science.gov (United States)

    Woolford, M J; Chadwick, R G

    1992-12-01

    The recently developed group of materials known as light-activated, or resin-modified, glass polyalkenoate (ionomer) cements have been produced in response to clinical demands for a command set cavity base material. This study monitored the surface pH of three commercially available resin-modified glass ionomer cements over a 60-min period following either mixing alone or mixing followed by a 30-s exposure to a curing lamp. The results indicate that each material behaves in a unique manner. For all materials and conditions the pH reached after a 60-min period was significantly (P pH of two of the materials (Baseline VLC and Vitrebond) as compared to the same materials in the uncured state. In the case of XR-Ionomer, however, no significant (P > 0.05) effect of light curing upon the surface pH was apparent. The precise clinical consequences of a low surface pH are unclear but may be an aetiological factor in postoperative pulpal sensitivity. It is therefore recommended that a sublining of a proprietary calcium hydroxide lining material should be placed routinely beneath these materials and every effort made to ensure effective light curing.

  20. The electrochemical behavior and surface structure of titanium electrodes modified by ion beams

    International Nuclear Information System (INIS)

    Huang, G.F.; Xie, Z.; Huang, W.Q.; Yang, S.B.; Zhao, L.H.

    2004-01-01

    Industrial grade titanium modified by ion implantation and sputtering was used as electrodes. The effect of ion beam modification on the electrochemical behavior and surface structure of electrodes was investigated. Also discussed is the hydrogen evolution process of the electrode in acidic solution. Several ions such as Fe + , C + , W + , Ni + and others, were implanted into the electrode. The electrochemical tests were carried out in 1N H 2 SO 4 solution at 30±1 deg. C. The electrode potential was measured versus a saturate calomel electrode as a function of immersion time. The cathodic polarization curves were measured by the stable potential static method. The surface layer composition and the chemical state of the electrodes were also investigated by Auger electron spectrometer (AES) and X-ray photoelectron spectroscopy (XPS) technique. The results show that: (1) the stability of modified electrodes depends on the active elements introduced by ion implantation and sputtering deposition. (2) The hydrogen evolution activity of industrial grade titanium may be improved greatly by ion beam modification. (3) Ion beam modification changed the composition and the surface state of electrodes over a certain depth range and forms an activity layer having catalytic hydrogen evolution, which inhibited the absorption of hydrogen and formation of titanium hydride. Thus promoted hydrogen evolution and improved the hydrogen evolution catalytic activity in industrial grade titanium

  1. Investigation of the biofouling properties of several algae on different textured chemical modified silicone surfaces

    International Nuclear Information System (INIS)

    Xu, Jihai; Zhao, Wenjie; Peng, Shusen; Zeng, Zhixiang; Zhang, Xin; Wu, Xuedong; Xue, Qunji

    2014-01-01

    Highlights: • Engineered pillars, pits and grooves spaced 3–12 μm apart were fabricated on siloxane modified acrylic resin films. • The effect of feature size, geometry, and wettability on the settlement of different algae was evaluated. • The feature size and geometry displayed a substantial correlation with the antifouling properties. • A comparatively physical fouling deterrent mechanism was analyzed. - Abstract: Engineered pillars, pits and grooves spaced 3, 6, 9 and 12 μm apart were fabricated on siloxane modified acrylic resin films. The effect of feature size, geometry, and wettability on the settlement of different algae was evaluated. These films showed various antifouling performances to Ulothrix, Closterium and Navicula. For Navicula (length: 10–12 μm), the feature size and geometry displayed a substantial correlation with the antifouling properties. The film with pillars spaced 3 μm reduced Navicula settlement by 73% compared to the control surface. For Closterium (length: 45–55 μm), their responses were governed by the same underlying thermodynamic principles as wettability, the largest reduction in Closterium, 81%, was obtained on the surface with grooves spaced 12 μm apart. For Ulothrix (length: 5–8 mm), the surface also showed the best antifouling performance, the reduction ratio of the settlement on the surface with grooves spaced 12 μm apart could even reach 92%. At last, physical fouling deterrent mechanisms for the films with various textures were analyzed in detail. The feature size and geometry display a substantial correlation with the antifouling properties when the size of fouling algae is close to the textures. With the increasing size for algae, antifouling performance was getting better on surface with pillars or grooves because the algae are bridged between two or more features other than stabilizing its entire mass on one single feature or able to settle between features

  2. Effects of various surfactants on the dispersion stability and electrical conductivity of surface modified graphene

    Energy Technology Data Exchange (ETDEWEB)

    Uddin, Md. Elias [WCU Program, Department of BIN Fusion Technology, Chonbuk National University, Jeonju, Jeonbuk 561-756 (Korea, Republic of); Kuila, Tapas [Surface Engineering and Tribology, CSIR – Central Mechanical Engineering Research Institute, Durgapur 721 302 (India); Nayak, Ganesh Chandra [Department of Applied Chemistry, ISM Dhanbad, Dhanbad 826 004, Jharkhand (India); Kim, Nam Hoon [Department of Hydrogen and Fuel Cell Engineering, Chonbuk National University, Jeonju, Jeonbuk 561-756 (Korea, Republic of); Ku, Bon-Cheol [Institute of Advanced Composite Materials, Korea Institute of Science and Technology, Dunsan-ri, Bongdong-eup, Wanju-gun, Jeollabuk-do 864-9 (Korea, Republic of); Lee, Joong Hee, E-mail: jhl@chonbuk.ac.kr [WCU Program, Department of BIN Fusion Technology, Chonbuk National University, Jeonju, Jeonbuk 561-756 (Korea, Republic of); Department of Hydrogen and Fuel Cell Engineering, Chonbuk National University, Jeonju, Jeonbuk 561-756 (Korea, Republic of)

    2013-06-15

    Highlights: ► Water dispersible graphene has been prepared using ionic and non-ionic surfactants. ► XPS and FTIR spectra analysis confirm surface modification and reduction of GO. ► The highest water dispersibility is observed in the graphene modified with of SDBS. ► The best properties of modified graphene is achieved with GO/surfactant ratio of two. -- Abstract: Ionic and non-ionic surfactant functionalized, water dispersible graphene were prepared to investigate the effects on the dispersion stability and electrical conductivity of graphene. In this study, sodium dodecyl benzene sulfonate (SDBS), sodium dodecyl sulfate and 4-(1,1,3,3-tetramethylbutyl) phenyl-polyethylene glycol (Triton X-100) were used as ionic and non-ionic surfactants. The effects of surfactant concentrations on the dispersibility and electrical conductivity of the surface modified graphene were investigated. The dispersion stability of SDBS functionalized graphene (SDBS-G) was found to be best in water at 1.5 mg ml{sup −1}. X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy analysis indicate that the presence of surfactants does not prevent the reduction of graphene oxide (GO). These measurements also demonstrated that the surfactants were present on the surface of graphene, resulting in the formation of functionalized graphene. The thickness of different functionalized graphene was measured by Atomic force microscopy and varied significantly with different surfactants. The thermal properties of the functionalized graphene were also found to be dependent on the nature of the surfactants. The electrical conductivity of SDBS-G (108 S m{sup −1}) was comparatively higher than SDS and Triton X-100 functionalized graphene.

  3. Effects of various surfactants on the dispersion stability and electrical conductivity of surface modified graphene

    International Nuclear Information System (INIS)

    Uddin, Md. Elias; Kuila, Tapas; Nayak, Ganesh Chandra; Kim, Nam Hoon; Ku, Bon-Cheol; Lee, Joong Hee

    2013-01-01

    Highlights: ► Water dispersible graphene has been prepared using ionic and non-ionic surfactants. ► XPS and FTIR spectra analysis confirm surface modification and reduction of GO. ► The highest water dispersibility is observed in the graphene modified with of SDBS. ► The best properties of modified graphene is achieved with GO/surfactant ratio of two. -- Abstract: Ionic and non-ionic surfactant functionalized, water dispersible graphene were prepared to investigate the effects on the dispersion stability and electrical conductivity of graphene. In this study, sodium dodecyl benzene sulfonate (SDBS), sodium dodecyl sulfate and 4-(1,1,3,3-tetramethylbutyl) phenyl-polyethylene glycol (Triton X-100) were used as ionic and non-ionic surfactants. The effects of surfactant concentrations on the dispersibility and electrical conductivity of the surface modified graphene were investigated. The dispersion stability of SDBS functionalized graphene (SDBS-G) was found to be best in water at 1.5 mg ml −1 . X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy analysis indicate that the presence of surfactants does not prevent the reduction of graphene oxide (GO). These measurements also demonstrated that the surfactants were present on the surface of graphene, resulting in the formation of functionalized graphene. The thickness of different functionalized graphene was measured by Atomic force microscopy and varied significantly with different surfactants. The thermal properties of the functionalized graphene were also found to be dependent on the nature of the surfactants. The electrical conductivity of SDBS-G (108 S m −1 ) was comparatively higher than SDS and Triton X-100 functionalized graphene

  4. The effect of salivary pH on diametral tensile strength of resin modified glass ionomer cement coated with coating agent

    Science.gov (United States)

    Ismayanti, D.; Triaminingsih, S.; Eriwati, Y. K.

    2017-08-01

    The aim of this study was to evaluate the effect of artificial saliva with different acidities on the diametral tensile strength of Resin Modified Glass Ionomer Cement (RMGIC) coated with varnish and nanofilled coating agent. The specimens coated with coating agents were immersed in artificial saliva with pH of 4.5, 5.5, and 7 for 24 hours in an incubatorat 37°C. The diametral tensile strength of the specimens was tested with Universal Testing Machine. There were no significant differences on the diametral tensile strength of all specimens that were put into groups based on the acidity of the saliva and the type of coating agent (p>0.05). Both varnish and nanofilled coating agent stayed on the RMGIC in the acidic condition that simulated the true condition of oral cavity in people with high caries risk for the 24 hours of maturation.

  5. Effect of antibacterial agents on the surface hardness of a conventional glass-ionomer cement

    Science.gov (United States)

    TÜZÜNER, Tamer; ULUSU, Tezer

    2012-01-01

    In atraumatic restorative treatment (ART), caries removal with hand excavation instruments is not as efficient as that with rotary burs in eliminating bacteria under the glass ionomer cements (GICs). Thus, different antibacterial agents have been used in recent studies to enhance the antibacterial properties of the GICs, without jeopardizing their basic physical properties. Objective The objective of this study was to evaluate the effect of antibacterial agents on the surface hardness of a conventional GIC (Fuji IX) using Vickers microhardness [Vickers hardness number (VHN)] test. Material and Methods Cetrimide (CT), cetylpyridinium chloride (CPC) and chlorhexidine (CHX) were added to the powder and benzalkonium chloride (BC) was added to the liquid of Fuji IX in concentrations of 1% and 2%, and served as the experimental groups. A control group containing no additive was also prepared. After the completion of setting reaction, VHN measurements were recorded at 1, 7, 15, 30, 60, and 90 days after storage in 37ºC distilled water. A one-way ANOVA was performed followed by a Dunnett t test and Tamhane T2 tests and also repeated measurements ANOVA was used for multiple comparisons in 95% confidence interval. Results VHN results showed significant differences between the control and the experimental groups at all time periods (phardness of set cements. Conclusions Despite the decreased microhardness values in all experimental groups compared to the controls after 7 up to 90 days, incorporating certain antibacterial agents into Fuji IX GIC showed tolerable microhardness alterations within the limitations of this in vitro study. PMID:22437677

  6. Surface-Active Agents for Isolation of the Core Component of Avian Myeloblastosis Virus 1

    Science.gov (United States)

    Stromberg, Kurt

    1972-01-01

    Sixty-one surface-active agents were evaluated in a procedure designed to assess their ability to remove the envelope from the core component of avian myeloblastosis virus (AMV). The procedure consisted of centrifugation of intact AMV through a series of sucrose gradients each containing an upper layer of agent at one of eight concentrations between 0.01 and 10%. The effectiveness of an agent in producing AMV cores was indicated by (i) the appearance of light-scattering bands in the region of core buoyant density in gradient tubes; (ii) the range of surfactant concentration over which these bands appeared; and (iii) an electron microscopy assessment by the negative-staining technique of the relative proportion of core to non-core material in each of these bands. Six nonionic surfactants were selected by this screening method for comparison in regard to recovery of core protein and endogenous ribonucleic acid (RNA)-dependent deoxyribonucleic acid (DNA) polymerase activity, as well as further morphologic evaluation by electron microscopy. The nonionic surfactants of the polyoxyethylene alcohol class (particularly, Sterox SL) were most effective. Nonionic surfactants of the polyoxyethylene alkylphenol class (particularly, Nonidet P-40) were also effective. Sterox SL and Nonidet P-40 each gave a more than fivefold increase in specific activity of endogenous RNA-dependent DNA polymerase, and each gave a low recovery of core protein. Sterox SL did not interfere to the extent that Nonidet P-40 did in procedures which involved spectrophotometric assay at 260 nm. The use of Sterox SL resulted in the least envelope contamination of core preparations by electron microscopy examination, the most recovery of protein and endogenous RNA-dependent DNA polymerase activity, and a core buoyant density in sucrose of 1.27 g/ml. Images PMID:4112071

  7. XPS analysis of the carbon fibers surface modified via HMDSO to carbon nanotube growth

    Energy Technology Data Exchange (ETDEWEB)

    Cardoso, L.D.R.; Gomes, M.C.B.; Trava-Airoldi, V.J.; Corat, E.J.; Lugo, D.C. [Instituto Nacional de Pesquisas Espaciais (INPE), Sao Jose dos Campos, SP (Brazil)

    2016-07-01

    Full text: Carbon fibers (CF) have been widely used to reinforce structural composites. Due to their strength-to-weight properties, CF composites are finding increased structural uses in areas such as aerospace, aeronautical, automobile and others. The strength of the fiber-resin interface bond has been found to be the limiting factor to the mechanical properties of CF-epoxy materials, due to their non-polar nature that limit the affinity of CF to bind chemically to any matrix. The growth of carbon nanotubes (CNTs) on the surface of CF is a promising approach for improving mechanical, electrical and thermal properties of structural composites. However growing CNTs on CF presents some obstacles, such as diffusion of metal catalyst particles on CF, uneven CNT growth and loss of mechanical properties of CF. To avoid the diffusion of catalyst particles we modified the CF surface with hexamethyldisiloxane (HMDSO) at low temperature (400 °C), also preventing the loss of mechanical properties and allowing uniform CNTs growth. We deposited CNTs via floating catalyst method, with ferrocene providing the catalyst particle and the oxidative dehydrogenation reaction of acetylene providing the carbon. The CF surface modification was analyzed via X-ray photoelectron spectroscopy (XPS) and CNTs growth via scanning electron microscopy with field emission gun. The XPS analysis showed that HMDSO promotes the binding of oxygen to carbon and silicon present on CF surface, the chemical modification of the surface of the CF enables the uniform growth of carbon nanotubes. (author)

  8. XPS analysis of the carbon fibers surface modified via HMDSO to carbon nanotube growth

    International Nuclear Information System (INIS)

    Cardoso, L.D.R.; Gomes, M.C.B.; Trava-Airoldi, V.J.; Corat, E.J.; Lugo, D.C.

    2016-01-01

    Full text: Carbon fibers (CF) have been widely used to reinforce structural composites. Due to their strength-to-weight properties, CF composites are finding increased structural uses in areas such as aerospace, aeronautical, automobile and others. The strength of the fiber-resin interface bond has been found to be the limiting factor to the mechanical properties of CF-epoxy materials, due to their non-polar nature that limit the affinity of CF to bind chemically to any matrix. The growth of carbon nanotubes (CNTs) on the surface of CF is a promising approach for improving mechanical, electrical and thermal properties of structural composites. However growing CNTs on CF presents some obstacles, such as diffusion of metal catalyst particles on CF, uneven CNT growth and loss of mechanical properties of CF. To avoid the diffusion of catalyst particles we modified the CF surface with hexamethyldisiloxane (HMDSO) at low temperature (400 °C), also preventing the loss of mechanical properties and allowing uniform CNTs growth. We deposited CNTs via floating catalyst method, with ferrocene providing the catalyst particle and the oxidative dehydrogenation reaction of acetylene providing the carbon. The CF surface modification was analyzed via X-ray photoelectron spectroscopy (XPS) and CNTs growth via scanning electron microscopy with field emission gun. The XPS analysis showed that HMDSO promotes the binding of oxygen to carbon and silicon present on CF surface, the chemical modification of the surface of the CF enables the uniform growth of carbon nanotubes. (author)

  9. Nanostructured lipid carrier surface modified with Eudragit RS 100 and its potential ophthalmic functions

    Science.gov (United States)

    Zhang, Wenji; Li, Xuedong; Ye, Tiantian; Chen, Fen; Yu, Shihui; Chen, Jianting; Yang, Xinggang; Yang, Na; Zhang, Jinsong; Liu, Jinlu; Pan, Weisan; Kong, Jun

    2014-01-01

    This study was carried out to evaluate the ocular performance of a cationic Eudragit (EDU) RS 100-coated nanostructured lipid carrier (NLC). The genistein encapsulated NLC (GEN-NLC) was produced using the melt-emulsification technique followed by surface absorption of EDU RS 100. The EDU RS 100 increased the surface zeta potential from −7.46 mV to +13.60 mV, by uniformly forming a spherical coating outside the NLC surface, as shown by transmission electron microscopy images. The EDU RS 100 on the NLC surface effectively improved the NLC stability by inhibiting particle size growth. The obtained EDU RS 100-GEN-NLC showed extended precorneal clearance and a 1.22-fold increase in AUC (area under the curve) compared with the bare NLC in a Gamma scintigraphic evaluation. The EDU RS 100 modification also significantly increased corneal penetration producing a 3.3-fold increase in apparent permeability coefficients (Papp) compared with references. Draize and cytotoxicity testing confirmed that the developed EDU RS 100-GEN-NLC was nonirritant to ocular tissues and nontoxic to corneal cells. These results indicate that the NLC surface modified by EDU RS 100 significantly improves the NLC properties and exhibits many advantages for ocular use. PMID:25246787

  10. Retention of in-situ surface modified silica nanoparticles for carbon dioxide foam stabilization in sandpack

    Science.gov (United States)

    Adil, Muhammad

    2014-10-01

    Nanoparticle-stabilized CO2 foams have been used for mobility control for CO2 flooding; however, raw nanosilica particles which are hydrophilic in nature tend to develop unstable CO2 foam under certain reservoir conditions. The unstable foam leads to particles aggregation resulting in complete retention while propagating in a long distance, deep into the reservoir. This can be avoided by the application of a particular coating of a specific surfactant, polymer or their combination to the surface of the nanoparticles. The in-situ surface activation of unmodified SiO2 nanoparticles by interaction with mixed surfactant (TX100:SDBS) in aqueous media has been studied with extensive experiments using variable volumetric ratios. The retention of in-situ surface-modified nanoparticles was evaluated by the injection of the dispersion of nanoparticles through a sandpack. The loading of nanoparticles in dispersion was ranging from concentrated (5 wt %) to dilute (0.1 wt %). Effluent nanoparticles concentration histories were measured to determine the retained particles in the sandpack. Little retention (injected over two pore volumes) was attained for 0.5% SiO2 and volumetric ratio of 2:1 (TX100:SDBS). These results were concluded in terms of surface charges, adsorption isotherm, surface adsorption, and DLVO theory between particles and rock.

  11. Relationship between leukotriene-modifying agent prescriptions dispensed and rate of suicide deaths by county in the US

    Directory of Open Access Journals (Sweden)

    Schumock GT

    2011-09-01

    Full Text Available Glen T Schumock1, Robert D Gibbons2, Todd A Lee1,3,4,6, Min J Joo4, Robert J Valuck5, Leslie T Stayner61Center for Pharmacoeconomic Research, and Department of Pharmacy Practice, College of Pharmacy, University of Illinois at Chicago, Chicago, IL, USA; 2Center for Health Statistics, and Departments of Medicine and Health Studies, Pritzker School of Medicine, University of Chicago, Chicago, IL, USA; 3Center for Management of Complex Chronic Care, Hines VA Hospital, Hines, IL, USA; 4Section of Pulmonary, Critical Care, Sleep and Allergy, Department of Medicine, College of Medicine, University of Illinois at Chicago, Chicago, IL, USA; 5Department of Clinical Pharmacy, School of Pharmacy, University of Colorado, Aurora, CO, USA; 6Division of Epidemiology and Biostatistics, School of Public Health, University of Illinois at Chicago, Chicago, IL, USABackground: The US Food and Drug Administration has issued warnings about a potential link between leukotriene receptor-modifying agents (LTMA and suicide. These warnings are based on case reports and there is controversy about the association. While spontaneous reporting of suicide-related events attributed to LTMA has risen dramatically, these data may be biased by the warnings. The objective of this study was to explore the relationship between LTMA and suicide deaths using event data preceding the Food and Drug Administration warnings.Methods: We conducted a mixed-effects Poisson regression analysis of the association between LTMA prescriptions dispensed and suicide deaths at the county level. Counts of suicide deaths in each US county, stratified by race, age group, gender, and year were obtained from the National Center for Health Statistics for the period January 1, 1999 to December 31, 2006. Counts of LTMA prescriptions dispensed in each US county were obtained from IMS Health Incorporated. The model estimated the overall suicide rate conditional on LTMA use, adjusted for age, gender, race, year

  12. Tensile bond strength of hydroxyethyl methacrylate dentin bonding agent on dentin surface at various drying techniques

    Directory of Open Access Journals (Sweden)

    Kun Ismiyatin

    2010-06-01

    Full Text Available Background: There are several dentin surface drying techniques to provide a perfect resin penetration on dentin. There are two techniques which will be compared in this study. The first technique was by rubbing dentin surface gently using cotton pellet twice, this technique is called blot dry technique. The second technique is by air blowing dentin surface for one second and continued by rubbing dentin surface gently using moist cotton. Purpose: This experiment was aimed to examine the best dentin surface drying techniques after 37% phosphoric acid etching to obtain the optimum tensile bond strength between hydroxyethyl methacrylate (HEMA and dentin surface. Method: Bovine teeth was prepared flat to obtain the dentin surface and than was etched using 37% phosphoric acid for 15 seconds. After etching the dentin was cleaned using 20 cc plain water and dried with blot dry techniques (group I, or dried with air blow for one second (group II, or dried with air blow for one second, and continued with rubbing gently using moist cotton pellet (group III, and without any drying as control group (group IV. After these drying, the dentin surfaces were applied with resin dentin bonding agent and put into plunger facing the composite mould. The antagonist plunger was filled with composite resin. After 24 hours, therefore bond strength was measured using Autograph. Result: Data obtained was analyzed using One-Way ANOVA with 95% confidence level and continued with LSD test on p≤0.05. The result showed that the highest tensile bond strength was on group I, while the lowest on group IV. Group II and IV, III and IV, II and III did not show signigicant difference (p>0.05. Conclusion: Dentin surface drying techniques through gentle rubbing using cotton pellet twice (blot dry technique gave the greatest tensile bond strength.Latar belakang masalah: Tehnik pengeringan permukaan dentin agar resin dapat penetrasi dengan sempurna adalah dengan cara pengusapan secara

  13. Surface modification of TiO2 nanotubes by grafting with APTS coupling agents

    Science.gov (United States)

    Phan Duong, Hong; Le, Minh Duc; Dao, Hung Cuong; Chen, Chia-Yun

    2017-10-01

    Titanium dioxide nanotubes (TNTs) have been considered the promising nanostructures employed for many practical applications such as biomedical, photonic and optoelectronic devices. Nevertheless, strong aggregation of TNTs within various aqueous media significantly hindered their practical utilizations and the capability of dispersing TNTs in the desired solvents are urgent to be improved. Therefore, in this study, the methodic investigations have been performed on the grafted modification of 3-aminopropyl triethoxysilane (APTS) on the surfaces of synthesized TNTs. A preliminary study was carried out to evaluate the influences of key parameters, including the concentrations of coupling agents, temperatures and the reaction durations, on the grafting efficiency of the aminosilane using Statistical design of experiments (DoE) methodology. TNTs with approximately 10–20 nm in diameter were prepared with the controlled hydrothermal treatment of commercialized P25 particles. The obtained products were revealed by the modern physicochemical systems including x-ray diffraction (XRD), transmission electron microscopy (TEM) and Brunauer-Emmett-Teller (BET) analysis. The additions of silane agent, reaction temperature and time have been adjusted to reveal the influences of the grafting efficiency (from 2.5 to 7.8 wt %) by thermal gravimetric analysis (TGA). Analysis of Fourier transform infrared spectroscopy (FTIR) has confirmed the successful link of Ti–O–Si chemical bonds on the grafted TNTs.

  14. Silicon and germanium nanoparticles with tailored surface chemistry as novel inorganic fiber brightening agents.

    Science.gov (United States)

    Deb-Choudhury, Santanu; Prabakar, Sujay; Krsinic, Gail; Dyer, Jolon M; Tilley, Richard D

    2013-07-31

    Low-molecular-weight organic molecules, such as coumarins and stilbenes, are used commercially as fluorescent whitening agents (FWAs) to mask photoyellowing and to brighten colors in fabrics. FWAs achieve this by radiating extra blue light, thus changing the hue and also adding to the brightness. However, organic FWAs can rapidly photodegrade in the presence of ultraviolet (UV) radiation, exacerbating the yellowing process through a reaction involving singlet oxygen species. Inorganic nanoparticles, on the other hand, can provide a similar brightening effect with the added advantage of photostability. We report a targeted approach in designing new inorganic silicon- and germanium-based nanoparticles, functionalized with hydrophilic (amine) surface terminations as novel inorganic FWAs. When applied on wool, by incorporation in a sol-gel Si matrix, the inorganic FWAs improved brightness properties, demonstrated enhanced photostability toward UV radiation, especially the germanium nanoparticles, and also generated considerably lower levels of reactive oxygen species compared to a commercial stilbene-based organic FWA, Uvitex NFW.

  15. Modified polarimetric bidirectional reflectance distribution function with diffuse scattering: surface parameter estimation

    Science.gov (United States)

    Zhan, Hanyu; Voelz, David G.

    2016-12-01

    The polarimetric bidirectional reflectance distribution function (pBRDF) describes the relationships between incident and scattered Stokes parameters, but the familiar surface-only microfacet pBRDF cannot capture diffuse scattering contributions and depolarization phenomena. We propose a modified pBRDF model with a diffuse scattering component developed from the Kubelka-Munk and Le Hors et al. theories, and apply it in the development of a method to jointly estimate refractive index, slope variance, and diffuse scattering parameters from a series of Stokes parameter measurements of a surface. An application of the model and estimation approach to experimental data published by Priest and Meier shows improved correspondence with measurements of normalized Mueller matrix elements. By converting the Stokes/Mueller calculus formulation of the model to a degree of polarization (DOP) description, the estimation results of the parameters from measured DOP values are found to be consistent with a previous DOP model and results.

  16. Investigation of Streptococcus mutans biofilm growth on modified Au(111)-surfaces using AFM and electrochemistry

    DEFF Research Database (Denmark)

    Hu, Yifan; Zhang, Jingdong; Ulstrup, Jens

    2011-01-01

    Biofilms of the bacterium Streptococcus mutans constitute perhaps the most important direct cause of human dental caries formation. We have studied S. mutans biofilm formation and properties on Au(111)-surfaces modified by self-assembled molecular monolayers (SAMs) of different thiol...... (hexadecanethiol, MHD) or hydrophilic (mercapto-hexadecanoic acid, MHDA) end groups. The voltammetric reductive desorption (RD) peaks of the thiol-based SAMs in the absence and presence of biofilms and growth medium was in focus as a sensitive probe of the SAM local environment.AFM showed that S. mutans had grown...... with growth medium or of the growth medium alone. The RD peak potential of the hydrophilic MHDA surface remained, further largely unaffected but the RD peak of the hydrophobic MHD SAM is distinctly shifted compared to the MHD SAM alone. The shifts were further in different directions for the S. mutans biofilm...

  17. Evaluation of the susceptibility to pitting corrosion of structural steels, including steels with modified surface

    International Nuclear Information System (INIS)

    Lunarska, E.; Nikiforow, K.

    2001-01-01

    Although the low alloy ferrite-perlite and bainite-martensite steels mostly undergo the general corrosion, pitting corrosion occurring under certain conditions jeopardizes the safety of installations, causing perforation of walls or initiation of crack. On the basis of electrochemical, corrosion and microscopic examinations, the conditions simulating typical industrial corrosion environments, containing Cl - ions have been selected, to which the parts of machines, devices and installation are subjected. The test parameters provide the preferential pitting corrosion without prevailing general corrosion, and provide the similar type of corrosion of different kinds of ferrite-perlite and bainite-martensite steels, including steels with modified surface layer. The proposed express method allows to evaluate the susceptibility to pitting corrosion and to evaluate the effect of surface modification on susceptibility to pitting corrosion in environments containing Cl - ions. The method may be applied for the proper selection of materials exploited under pitting corrosion conditions and for preparation of precorroded samples for mechanical testing. (author)

  18. High-Throughput Fabrication of Quality Nanofibers Using a Modified Free Surface Electrospinning

    Science.gov (United States)

    Shao, Zhongbiao; Yu, Liang; Xu, Lan; Wang, Mingdi

    2017-07-01

    Based on bubble electrospinning (BE), a modified free surface electrospinning (MFSE) using a cone-shaped air nozzle combined with a solution reservoir made of copper tubes was presented to increase the production of quality nanofibers. In the MFSE process, sodium dodecyl benzene sulfonates (SDBS) were added in the electrospun solution to generate bubbles on a liquid surface. The effects of applied voltage and generated bubbles on the morphology and production of nanofibers were investigated experimentally and theoretically. The theoretical analysis results of the electric field were in good agreement with the experimental data and showed that the quality and production of nanofibers were improved with the increase of applied voltage, and the generated bubbles would decrease the quality and production of nanofibers.

  19. PERFORMANCE OF CEMENT COMPOSITES REINFORCED WITH SURFACE-MODIFIED POLYPROPYLENE MICRO- AND MACRO-FIBERS

    Directory of Open Access Journals (Sweden)

    Jakub Antoš

    2017-11-01

    Full Text Available This paper focuses on the mechanical properties investigation of cement pastes reinforced with surface treated polymer fibers. The cement matrix was composed of Portland cement (CEM I 42.5 R, w/c ratio equal to 0.4. Two polypropylene fiber types (micro- and macro-fibers were used as randomly distributed and oriented reinforcement in volume amount of 2 %. The fibers were modified in the low-pressure inductively coupled cold oxygen plasma in order to enhance their surface interaction with the cement matrix. The investigated composite mechanical properties (load bearing capacity and response during loading were examined indirectly by means of four-point bending mechanical destructive tests. A response of loaded samples containing treated fibers were compared to samples with reference fibers. Moreover, cracking behavior development was monitored using digital image correlation (DIC. This method enabled to record the micro-cracks system evaluation of both fiber reinforced samples.

  20. Iron carbide on titania surface modified with group VA oxides as Fischer-Tropsch catalysts

    International Nuclear Information System (INIS)

    Wachs, I.E.; Fiato, R.A.; Chersich, C.C.

    1986-01-01

    A catalyst is described comprising iron carbide supported on a surface modified titania wherein the support comprises an oxide of a metal selected form the group consisting of niobium, vanadium, tantalum or mixture thereof supported on the titania wherein at least a portion of the supported oxide of niobium, vanandium, tantalum or mixture is in a non-crystalline form. The amount of the supported oxide ranges from about 0.5 to 25 weight percent metal oxide on the titania support based on the total support composition and the catalyst contains at least about 2 milligrams of iron, calculated as Fe/sub 2/O/sub 3/, per square meter of support surface

  1. Potential dependent adhesion forces on bare and underpotential deposition modified electrode surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Serafin, J.M.; Hsieh, S.J.; Monahan, J.; Gewirth, A.A. [Univ. of Illinois, Urbana, IL (United States)

    1998-12-03

    Adhesion force measurements are used to determine the potential dependence of the force of adhesion between a Si{sub 3}N{sub 4} cantilever and a Au(111) surface modified by the underpotential deposition (upd) of Bi or Cu in acid solution or by oxide formation. The measured work of adhesion is near zero for most of the potential region examined in Bi upd but rises after the formation of a full Bi monolayer. The work of adhesion is high at positive potentials for Cu upd but then decreases as the Cu partial and full monolayers are formed. The work of adhesion is low in the oxide region on Au(111) but rises following the sulfate disordering transition at 1.1 V vs NHE. These results are interpreted in terms of the degree of solvent order on the electrode surface.

  2. Dithiocarbamate Self-Assembled Monolayers as Efficient Surface Modifiers for Low Work Function Noble Metals

    Energy Technology Data Exchange (ETDEWEB)

    Meyer, Dominik; Schäfer, Tobias; Schulz, Philip; Jung, Sebastian; Rittich, Julia; Mokros, Daniel; Segger, Ingolf; Maercks, Franziska; Effertz, Christian; Mazzarello, Riccardo; Wuttig, Matthias

    2016-09-06

    Tuning the work function of the electrode is one of the crucial steps to improve charge extraction in organic electronic devices. Here, we show that N,N-dialkyl dithiocarbamates (DTC) can be effectively employed to produce low work function noble metal electrodes. Work functions between 3.1 and 3.5 eV are observed for all metals investigated (Cu, Ag, and Au). Ultraviolet photoemission spectroscopy (UPS) reveals a maximum decrease in work function by 2.1 eV as compared to the bare metal surface. Electronic structure calculations elucidate how the complex interplay between intrinsic dipoles and dipoles induced by bond formation generates such large work function shifts. Subsequently, we quantify the improvement in contact resistance of organic thin film transistor devices with DTC coated source and drain electrodes. These findings demonstrate that DTC molecules can be employed as universal surface modifiers to produce stable electrodes for electron injection in high performance hybrid organic optoelectronics.

  3. Immobilization of Phosphomolybdate Anions on the Surface of Magnetite Nanoparticles Modified with Quaternary Phosphonium Cations

    Directory of Open Access Journals (Sweden)

    M. Masteri-Farahani

    2013-06-01

    Full Text Available A new hybrid nanomaterial was developed by immobilization of phosphomolybdate anions on the surface of modified magnetite nanoparticles with quaternary phosphonium cations. Silica coated magnetic nanoparticles supported phosphonium cations, Ph3P+-SCMNPs, were prepared by covalent attachment of chloropropylsilyl groups on the surface of silica coated magnetite nanoparticles and next reaction with triphenylphosphine. Then, reaction of the prepared Ph3P+-SCMNPs nanomaterial with H3PMo12O40 resulted in the preparation of PMo-Ph3P+-SCMNPs hybrid nanomaterial. The PMo-Ph3P+-SCMNPs hybrid nanomaterial was characterized with different physicochemical methods such as FT-IR and ICP-AES spectroscopies, XRD, VSM, SEM, and TEM analyses. VSM analysis showed superparamagnetic properties of the prepared nanomaterial. TEM and SEM analyses indicated the aggregated nanoparticles with about 15 nm average size.

  4. Improved Performance of Dye-Sensitized Solar Cells Using a Diethyldithiocarbamate-Modified Surface

    Directory of Open Access Journals (Sweden)

    D. M. B. P. Ariyasinghe

    2013-01-01

    Full Text Available The surface modification of a TiO2 electrode with diethyldithiocarbamate (DEDTC in dye-sensitized solar cells (DSSCs was studied. Results from X-ray photoelectron spectroscopy (XPS indicate that over half of the sulfur atoms become positively charged after the DEDTC treatment of the TiO2 surface. DSSCs were fabricated with TiO2 electrodes modified by adsorbing DEDTC using a simple dip-coating process. The conversion efficiency of the DSSCs has been optimized to 6.6% through the enhancement of the short-circuit current density ( mA/cm2. This is substantially higher compared to the efficiency of 5.9% ( mA/cm2 for the DSSCs made with untreated TiO2 electrodes.

  5. Enhanced Group Delay of the Pulse Reflection with Graphene Surface Plasmon via Modified Otto Configuration

    Directory of Open Access Journals (Sweden)

    Guimei Li

    2017-01-01

    Full Text Available In this paper, the group delay of the transverse magnetic (TM polarized wave reflected from a modified Otto configuration with graphene surface plasmon is investigated theoretically. The findings show that the optical group delay in this structure can be enhanced negatively and can be switched from negative to positive due to the excitation of surface plasmon by graphene. It is clear that the negative group delay can be actively tuned through the Fermi energy of the graphene. Furthermore, the delay properties can also be manipulated by changing either the relaxation time of graphene or the distance between the coupling prism and the graphene. These tunable delay characteristics are promising for fabricating grapheme-based optical delay devices and other applications in the terahertz regime.

  6. High-Throughput Fabrication of Quality Nanofibers Using a Modified Free Surface Electrospinning.

    Science.gov (United States)

    Shao, Zhongbiao; Yu, Liang; Xu, Lan; Wang, Mingdi

    2017-12-01

    Based on bubble electrospinning (BE), a modified free surface electrospinning (MFSE) using a cone-shaped air nozzle combined with a solution reservoir made of copper tubes was presented to increase the production of quality nanofibers. In the MFSE process, sodium dodecyl benzene sulfonates (SDBS) were added in the electrospun solution to generate bubbles on a liquid surface. The effects of applied voltage and generated bubbles on the morphology and production of nanofibers were investigated experimentally and theoretically. The theoretical analysis results of the electric field were in good agreement with the experimental data and showed that the quality and production of nanofibers were improved with the increase of applied voltage, and the generated bubbles would decrease the quality and production of nanofibers.

  7. Impact of the Ageing on Viscoelastic Properties of Bitumen with the Liquid Surface Active Agent at Operating Temperatures

    Science.gov (United States)

    Iwański, Marek; Cholewińska, Malgorzata; Mazurek, Grzegorz

    2017-10-01

    The paper presents the influence of the ageing on viscoelastic properties of the bitumen at road pavement operating temperatures. The ageing process of bituminous binders causes changes in physical and mechanical properties of the bitumen. This phenomenon takes place in all stages of bituminous mixtures manufacturing, namely: mixing, storage, transport, placing. Nevertheless, during the service life it occurs the increase in stiffness of asphalt binder that is caused by the physical hardening of bitumen as well as the influence of oxidation. Therefore, it is important to identify the binder properties at a high and low operating temperatures of asphalt pavement after simulation of an ageing process. In the experiment as a reference bitumen, the polymer modified bitumen PMB 45/80-65 was used. The liquid surface active agent FA (fatty amine) was used as a bitumen viscosity-reducing modifier. It was added in the amount of 0,2%, 0,4% and 0,6% by the bitumen mass. All binder properties have been determined before ageing (NEAT) and after long-term ageing simulated by the Pressure Ageing Vessel method (PAV). To determine the binder properties at high temperatures the dynamic viscosity at 60°C was tested. On the basis of test results coming from the dynamic viscosity test it was calculated the binder hardening index. The properties at a low temperature were determined by measuring the creep modulus using Bending Beam Rheometer (BBR) at four temperatures: -10°C, -16°C, -22°C and -28°C. The stiffness creep modulus “S” and parameter “m” were determined. On the basis of dynamic viscosity test it was found that the ageing process caused a slight decrease in a dynamic viscosity. The level of a hardening index considerably increased at 0.6% fatty amine content. The long-term ageing process had a minor effect on stiffening of a polymer modified bitumen with FA additive regardless of a low temperature and an amount of fatty amine content.

  8. New heterocycles having double characters; as antimicrobial and surface active agents.

    Directory of Open Access Journals (Sweden)

    El-Sayed, R.

    2004-12-01

    Full Text Available Fatty acids isothiocyanate (1 was used as a starting material to synthesize some important heterocycles such as triazoles, oxazoles, thiazoles, benzoxazoles and quinazolines by treating with different types of nucleophiles such as nitrogen nucleophiles, oxygen nucleophiles, and sulfur nucleophiles. The produced compounds were subjected to propylene oxide in different moles (n = 3, 5 and 7 to produce novel groups of nonionic compounds having the double function as antimicrobial and surface active agents which can be used in the manufacturing of drugs, cosmetics, pesticides or can be used as antibacterial and/or antifungal. The physical properties as surface and interfacial tension, cloud point, foaming height, wetting time, emulsification power and the critical micelle concentration (CMC were determined, antimicrobial and biodegradability were also determined.Isocianatos de acidos grasos se utilizaron como material de partida para la síntesis de importantes heterociclos tales como triazoles, oxazoles, thoazoles, benzoxazoles y quinazolinas mediante el tratamiento de los mismos con diferentes tipos de nucleofilos tales como nucleofilos nitrogenados, oxigenados, o azufrados. Los compuestos producidos se trataron con oxido de propileno a diferentes concentraciones molares (n = 3, 5 y 7 para producir nuevos grupos de compuestos no iónicos que tuvieran la doble función de ser compuestos antimicrobianos y agentes de superficie, que se pudieran usar en la fabricación de medicinas, cosméticos, pesticidas o como antibacterianos o antifúngicos. Se determinaron sus propiedades tales como tensión superficial e interfacial, punto de turbidez, altura de espuma, tiempo de mojado, poder de emulsificación y concentración micelar crítica (CMC, asi como sus propiedades antimicrobianas y de degradabilidad.

  9. Non-Fouling Character of Poly[2-(methacryloyloxy)ethyl Phosphorylcholine]-Modified Gold Surfaces Fabricated by the 'Grafting to' Method: Comparison of its Protein Resistance with Poly(ethylene glycol)-Modified Gold Surfaces.

    Science.gov (United States)

    Yoshimoto, Keitaro; Hirase, Takumi; Madsen, Jeppe; Armes, Steven P; Nagasaki, Yukio

    2009-12-16

    Poly[2-(methacryloyloxy)ethyl phosphorylcholine] -modified gold surfaces, which have been newly prepared by a 'grafting to' method using a series of monosulfanyl-terminated PMPC, are characterized by protein adsorption experiments based on surface plasmon resonance spectroscopy and ellipsometry measurements. The extent of BSA adsorption on PMPC-modified surfaces was systematically reduced for thicker PMPC layers, thus the number of MPC units on the gold surface appears to be an important factor for the excellent protein resistance offered by PMPC-modified gold surfaces fabricated by the 'grafting to' method, which is sharp contrast to that of PEG tethered chains. Copyright © 2009 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. Fabrication of endothelial progenitor cell capture surface via DNA aptamer modifying dopamine/polyethyleneimine copolymer film

    Energy Technology Data Exchange (ETDEWEB)

    Li, Xin; Deng, Jinchuan; Yuan, Shuheng; Wang, Juan; Luo, Rifang; Chen, Si [Key Lab. of Advanced Technology for Materials of Education Ministry, Southwest Jiaotong University, Chengdu 610031 (China); School of Material Science and Engineering, Southwest Jiaotong University, Chengdu 610031 (China); Wang, Jin, E-mail: jinxxwang@263.net [Key Lab. of Advanced Technology for Materials of Education Ministry, Southwest Jiaotong University, Chengdu 610031 (China); Huang, Nan [Key Lab. of Advanced Technology for Materials of Education Ministry, Southwest Jiaotong University, Chengdu 610031 (China); School of Material Science and Engineering, Southwest Jiaotong University, Chengdu 610031 (China)

    2016-11-15

    Highlights: • The dopamine/PEI film with controlled amine density was successfully prepared. • The DNA aptamer was assembled onto the film via electrostatic incorporation. • The A@DPfilmscanspecificallyandeffectivelycaptureEPCs. • The A@DP film can support the survival of ECs, control the hyperplasia of SMCs. • The dynamic/co-culture models are useful for studying cells competitive adhesion. - Abstract: Endothelial progenitor cells (EPCs) are mainly located in bone marrow and circulate, and play a crucial role in repairmen of injury endothelium. One of the most promising strategies of stents designs were considered to make in-situ endothelialization in vivo via EPC-capture biomolecules on a vascular graft to capture EPCs directly from circulatory blood. In this work, an EPC specific aptamer with a 34 bases single strand DNA sequence was conjugated onto the stent surface via dopamine/polyethyleneimine copolymer film as a platform and linker. The assembled density of DNA aptamer could be regulated by controlling dopamine percentage in this copolymer film. X-ray photoelectron spectroscopy (XPS), water contact angle (WCA) and fluorescence test confirmed the successful immobilization of DNA aptamer. To confirm its biofunctionality and cytocompatibility, the capturing cells ability of the aptamer modified surface and the effects on the growth behavior of human umbilical vein endothelial cells (HUVECs), smooth muscle cells (SMCs) were investigated. The aptamer functionalized sample revealed a good EPC-capture ability, and had a cellular friendly feature for both EPC and EC growth, while not stimulated the hyperplasia of SMCs. And, the co-culture experiment of three types of cells confirmed the specificity capturing of EPCs to aptamer modified surface, rather than ECs and SMCs. These data suggested that this aptamer functionalized surface may have a large potentiality for the application of vascular grafts with targeted endothelialization.

  11. Fabrication of endothelial progenitor cell capture surface via DNA aptamer modifying dopamine/polyethyleneimine copolymer film

    International Nuclear Information System (INIS)

    Li, Xin; Deng, Jinchuan; Yuan, Shuheng; Wang, Juan; Luo, Rifang; Chen, Si; Wang, Jin; Huang, Nan

    2016-01-01

    Highlights: • The dopamine/PEI film with controlled amine density was successfully prepared. • The DNA aptamer was assembled onto the film via electrostatic incorporation. • The A@DPfilmscanspecificallyandeffectivelycaptureEPCs. • The A@DP film can support the survival of ECs, control the hyperplasia of SMCs. • The dynamic/co-culture models are useful for studying cells competitive adhesion. - Abstract: Endothelial progenitor cells (EPCs) are mainly located in bone marrow and circulate, and play a crucial role in repairmen of injury endothelium. One of the most promising strategies of stents designs were considered to make in-situ endothelialization in vivo via EPC-capture biomolecules on a vascular graft to capture EPCs directly from circulatory blood. In this work, an EPC specific aptamer with a 34 bases single strand DNA sequence was conjugated onto the stent surface via dopamine/polyethyleneimine copolymer film as a platform and linker. The assembled density of DNA aptamer could be regulated by controlling dopamine percentage in this copolymer film. X-ray photoelectron spectroscopy (XPS), water contact angle (WCA) and fluorescence test confirmed the successful immobilization of DNA aptamer. To confirm its biofunctionality and cytocompatibility, the capturing cells ability of the aptamer modified surface and the effects on the growth behavior of human umbilical vein endothelial cells (HUVECs), smooth muscle cells (SMCs) were investigated. The aptamer functionalized sample revealed a good EPC-capture ability, and had a cellular friendly feature for both EPC and EC growth, while not stimulated the hyperplasia of SMCs. And, the co-culture experiment of three types of cells confirmed the specificity capturing of EPCs to aptamer modified surface, rather than ECs and SMCs. These data suggested that this aptamer functionalized surface may have a large potentiality for the application of vascular grafts with targeted endothelialization.

  12. Multifunctional ultra-high vacuum apparatus for studies of the interactions of chemical warfare agents on complex surfaces.

    Science.gov (United States)

    Wilmsmeyer, Amanda R; Gordon, Wesley O; Davis, Erin Durke; Mantooth, Brent A; Lalain, Teri A; Morris, John R

    2014-01-01

    A fundamental understanding of the surface chemistry of chemical warfare agents is needed to fully predict the interaction of these toxic molecules with militarily relevant materials, catalysts, and environmental surfaces. For example, rules for predicting the surface chemistry of agents can be applied to the creation of next generation decontaminants, reactive coatings, and protective materials for the warfighter. Here, we describe a multifunctional ultra-high vacuum instrument for conducting comprehensive studies of the adsorption, desorption, and surface chemistry of chemical warfare agents on model and militarily relevant surfaces. The system applies reflection-absorption infrared spectroscopy, x-ray photoelectron spectroscopy, and mass spectrometry to study adsorption and surface reactions of chemical warfare agents. Several novel components have been developed to address the unique safety and sample exposure challenges that accompany the research of these toxic, often very low vapor pressure, compounds. While results of vacuum-based surface science techniques may not necessarily translate directly to environmental processes, learning about the fundamental chemistry will begin to inform scientists about the critical aspects that impact real-world applications.

  13. Similar effects of disease-modifying antirheumatic drugs, glucocorticoids, and biologic agents on radiographic progression in rheumatoid arthritis: meta-analysis of 70 randomized placebo-controlled or drug-controlled studies, including 112 comparisons

    DEFF Research Database (Denmark)

    Graudal, Niels; Jürgens, Gesche

    2010-01-01

    To define the differences in effects on joint destruction in rheumatoid arthritis (RA) patients between therapy with single and combination disease-modifying antirheumatic drugs (DMARDs), glucocorticoids, and biologic agents.......To define the differences in effects on joint destruction in rheumatoid arthritis (RA) patients between therapy with single and combination disease-modifying antirheumatic drugs (DMARDs), glucocorticoids, and biologic agents....

  14. The biomedical properties of polyethylene terephthalate surface modified by silver ion implantation

    International Nuclear Information System (INIS)

    Wang Jin; Li Jianxin; Shen Liru; Ling Ren; Xu Zejin; Zhao Ansha; Leng Yongxiang; Huang Nan

    2007-01-01

    Polyethylene terephthalate (PET) film is modified by Ag ion implantation with a fluence 1 x 10 16 ions/cm 2 . The results of X-Ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) indicate that silver has been successfully implanted into the surface of PET. The PET samples modified by silver ion implantation have significantly bactericidal property. The capacity of the staphylococcus epidermidis (SE) adhered on the Ag + implanted PET surface is 5.3 x 10 6 CFU/ml, but the capacity of the SE adhered on the untreated PET film is 2.23 x 10 7 CFU/ml. The thromboembolic property is evaluated by in vitro platelet adhesion test, and there is not statistically difference between the untreated PET and the Ag + implanted PET for the number of adhered and activated platelets. The PET implanted by silver ion has not acute toxicity to endothelial cell (EC) which was evaluated by the release of lactate dehydrogenase (LDH) test

  15. Uniform surface-to-line integral reduction of physical optics for curved surfaces by modified edge representation with higher-order correction

    Science.gov (United States)

    Lyu, Pengfei; Ando, Makoto

    2017-09-01

    The modified edge representation is one of the equivalent edge currents approximation methods for calculating the physical optics surface radiation integrals in diffraction analysis. The Stokes' theorem is used in the derivation of the modified edge representation from the physical optics for the planar scatterer case, which implies that the surface integral is rigorously reduced into the line integral of the modified edge representation equivalent edge currents, defined in terms of the local shape of the edge. On the contrary, for curved surfaces, the results of radiation integrals depend upon the global shape of the scatterer. The physical optics surface integral consists of two components, from the inner stationary phase point and the edge. The modified edge representation is defined independently from the orientation of the actual edge, and therefore, it could be available not only at the edge but also at the arbitrary points on the scatterer except the stationary phase point where the modified edge representation equivalent edge currents becomes infinite. If stationary phase point exists inside the illuminated region, the physical optics surface integration is reduced into two kinds of the modified edge representation line integrations, along the edge and infinitesimally small integration around the inner stationary phase point, the former and the latter give the diffraction and reflection components, respectively. The accuracy of the latter has been discussed for the curved surfaces and published. This paper focuses on the errors of the former and discusses its correction. It has been numerically observed that the modified edge representation works well for the physical optics diffraction in flat and concave surfaces; errors appear especially for the observer near the reflection shadow boundary if the frequency is low for the convex scatterer. This paper gives the explicit expression of the higher-order correction for the modified edge representation.

  16. Modifying a dynamic global vegetation model for simulating large spatial scale land surface water balances

    Directory of Open Access Journals (Sweden)

    G. Tang

    2012-08-01

    Full Text Available Satellite-based data, such as vegetation type and fractional vegetation cover, are widely used in hydrologic models to prescribe the vegetation state in a study region. Dynamic global vegetation models (DGVM simulate land surface hydrology. Incorporation of satellite-based data into a DGVM may enhance a model's ability to simulate land surface hydrology by reducing the task of model parameterization and providing distributed information on land characteristics. The objectives of this study are to (i modify a DGVM for simulating land surface water balances; (ii evaluate the modified model in simulating actual evapotranspiration (ET, soil moisture, and surface runoff at regional or watershed scales; and (iii gain insight into the ability of both the original and modified model to simulate large spatial scale land surface hydrology. To achieve these objectives, we introduce the "LPJ-hydrology" (LH model which incorporates satellite-based data into the Lund-Potsdam-Jena (LPJ DGVM. To evaluate the model we ran LH using historical (1981–2006 climate data and satellite-based land covers at 2.5 arc-min grid cells for the conterminous US and for the entire world using coarser climate and land cover data. We evaluated the simulated ET, soil moisture, and surface runoff using a set of observed or simulated data at different spatial scales. Our results demonstrate that spatial patterns of LH-simulated annual ET and surface runoff are in accordance with previously published data for the US; LH-modeled monthly stream flow for 12 major rivers in the US was consistent with observed values respectively during the years 1981–2006 (R2 > 0.46, p < 0.01; Nash-Sutcliffe Coefficient > 0.52. The modeled mean annual discharges for 10 major rivers worldwide also agreed well (differences < 15% with observed values for these rivers. Compared to a degree-day method for snowmelt computation, the addition of the solar radiation effect on snowmelt

  17. Dispersing surface-modified imogolite nanotubes in polar and non-polar solvents

    Science.gov (United States)

    Li, Ming; Brant, Jonathan A.

    2018-02-01

    Furthering the development of nanocomposite structures, namely membranes for water treatment applications, requires that methods be developed to ensure nanoparticle dispersion in polar and non-polar solvents, as both are widely used in associated synthesis techniques. Here, we report on a two-step method to graft polyvinylpyrrolidone (PVP), and a one-step method for octadecylphosphonic acid (OPA), onto the outer surfaces of imogolite nanotubes. The goal of these approaches was to improve and maintain nanotube dispersion in polymer compatible polar and non-polar solvents. The PVP coating modified the imogolite surface charge from positive to weakly negative at pH ≤ 9; the OPA made it weakly positive at acidic pH values to negative at pH ≥ 7. The PVP surface coating stabilized the nanotubes through steric hindrance in polar protic, dipolar aprotic, and chloroform. In difference to the PVP, the OPA surface coating allowed the nanotubes to be dispersed in n-hexane and chloroform, but not in the polar solvents. The lack of miscibility in the polar solvents, as well as the better dispersion in n-hexane, was attributed to the stronger hydrophobicity of the OPA polymer relative to the PVP. [Figure not available: see fulltext.

  18. Influence of surface modified dental implant abutments on connective tissue attachment: A systematic review.

    Science.gov (United States)

    Blázquez-Hinarejos, Mónica; Ayuso-Montero, Raúl; Jané-Salas, Enric; López-López, José

    2017-08-01

    Determine whether surface modified prosthetic abutments for dental implants influence connective tissue attachment to the implant-abutment system. A systematic review was conducted using the MEDLINE-PubMed database, with two independent reviewers filtering the titles and abstracts. Two reviewers assessed all potentially relevant articles. An assessment was carried out on the level of evidence of the research according to the guidelines of the Oxford Centre for Evidence-Based Medicine (OCEBM). After an initial search, 109 potentially relevant articles were found. After reading the titles and abstracts, 99 articles were excluded because the surface treatment was limited to the implant and not to the abutment, or because different materials were analysed instead of surface treatments; 28 were also duplicate articles. An additional 6 research studies were included that were of interest and were found by reading the references of the included articles. The studies included are: 7 in vitro studies, 5 experimental studies in animals, 2 clinical trials in humans and 2 clinical cases. Surface modification for prosthetic abutments on dental implants can achieve connective tissue attachment to the abutment; however, more studies should be conducted in humans to obtain more and better evidence of these results. Copyright © 2017 Elsevier Ltd. All rights reserved.

  19. Mechanical, Thermal Degradation, and Flammability Studies on Surface Modified Sisal Fiber Reinforced Recycled Polypropylene Composites

    Directory of Open Access Journals (Sweden)

    Arun Kumar Gupta

    2012-01-01

    Full Text Available The effect of surface treated sisal fiber on the mechanical, thermal, flammability, and morphological properties of sisal fiber (SF reinforced recycled polypropylene (RPP composites was investigated. The surface of sisal fiber was modified with different chemical reagent such as silane, glycidyl methacrylate (GMA, and O-hydroxybenzene diazonium chloride (OBDC to improve the compatibility with the matrix polymer. The experimental results revealed an improvement in the tensile strength to 11%, 20%, and 31.36% and impact strength to 78.72%, 77%, and 81% for silane, GMA, and OBDC treated sisal fiber reinforced recycled Polypropylene (RPP/SF composites, respectively, as compared to RPP. The thermogravimetric analysis (TGA, differential scanning calorimeter (DSC, and heat deflection temperature (HDT results revealed improved thermal stability as compared with RPP. The flammability behaviour of silane, GMA, and OBDC treated SF/RPP composites was studied by the horizontal burning rate by UL-94. The morphological analysis through scanning electron micrograph (SEM supports improves surface interaction between fiber surface and polymer matrix.

  20. In vitro cytotoxicity and phototoxicity of surface-modified gold nanoparticles associated with neutral red as a potential drug delivery system in phototherapy

    Energy Technology Data Exchange (ETDEWEB)

    Verissimo, Tanira V. [School of Health Sciences, University of Brasilia, Brasilia (Brazil); Laboratory of Photochemistry and Nanobiotechnology, Faculty of Ceilandia, University of Brasilia, Brasilia (Brazil); Santos, Naiara T. [School of Health Sciences, University of Brasilia, Brasilia (Brazil); Silva, Jaqueline R.; Azevedo, Ricardo B. [Institute of Biological Sciences, University of Brasilia, Brasilia (Brazil); Gomes, Anderson J., E-mail: ajgomes@unb.br [School of Health Sciences, University of Brasilia, Brasilia (Brazil); Laboratory of Photochemistry and Nanobiotechnology, Faculty of Ceilandia, University of Brasilia, Brasilia (Brazil); Lunardi, Claure N., E-mail: clunardi@unb.br [School of Health Sciences, University of Brasilia, Brasilia (Brazil); Laboratory of Photochemistry and Nanobiotechnology, Faculty of Ceilandia, University of Brasilia, Brasilia (Brazil)

    2016-08-01

    The surface of gold nanoparticles (AuNP) was modified, improving their interaction with neutral red (NR), by using sodium thioglycolate (TGA) as a covering agent. The resulting NR-AuNPTGA system was evaluated as a potential drug delivery system for photodynamic therapy (PDT). The associations of NR with the gold nanoparticles were evaluated using UV-vis spectrometry and measurement of their zeta potential and size distribution. The toxicity and phototoxicity of NR, AuNPTGA and NR-AuNPTGA were evaluated in NIH-3T3 fibroblast and 4T1 tumor cell lines. The compounds NR and NR-AuNPTGA induced toxicity in 4T1 tumor cells and NIH-3T3 fibroblasts under visible light irradiation. Modification of the surface of AuNP with TGA prevented nanoparticle aggregation and allowed greater association with NR molecules than for naked AuNP. The photosensitizer (PS) characteristics were not affected by its association with the modified surface of the gold nanoparticles, leading to a reduction of cell viability in both cell lines assayed. This NR-AuNPTGA system is a promising drug delivery system for photodynamic cancer therapy. - Highlights: • Modified gold nanoparticle (AuNP) by sodium thioglicolate (TGA) prevents aggregation. • Neutral red (NR) adsorbed on the surface of modified gold nanoparticles (AuNPTGA). • AuNPTGA is suitable as a platform to deliver the NR under irradiation process. • Photodamage of 90% was achieved by NR added to AuNPTGA in 4T1 and NIH-3T3 cells.

  1. Immobilization of simulated reducing agent at the surface of SiO2 fillers in dental composite resins.

    Science.gov (United States)

    Shibata, Satoki; Hirata, Isao; Nomura, Yuji; Shirai, Kenichi; Fujitani, Morioki; Shintani, Hideaki; Okazaki, Masayuki

    2007-07-01

    To reduce the leachability of reducing agents from composite resins, immobilization of a simulated reducing agent at the surface of SiO2 fillers was examined. SiO2 plates were immersed in 2% 3-aminopropyltriethoxy silane/ethanol solution, and then immersed in dimethyl sulfoxide with 0.25 wt% 4-dimethyl amino benzoic acid (DMABA), 2.0 wt% 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide hydrochloride, and 0.5 wt% N-hydroxysuccinimide. Wide-scan spectrum of X-ray photoelectron spectroscopy did not detect carbon contamination. However, narrow scan detected an O=C-N peak at 399.8 eV, suggesting that DMABA could be immobilized on silane-coupled SiO2 plates. Further, surface plasmon resonance analysis indicated the adsorption of MMA at the surface of reducing agent-immobilized plate.

  2. Synthesis of nano-hydroxyapatite and its rapid mediated surface functionalization by silane coupling agent

    Energy Technology Data Exchange (ETDEWEB)

    Rehman, Sarish, E-mail: kknano@hotmail.com; Khan, Kishwar; Mujahid, Mohammad; Nosheen, Shaneela

    2016-01-01

    In this work, hydroxyapatite (HA) nanorods were synthesized by simple one step wet precipitation method followed by their rapid surface functionalization via aminopropyltriethoxysilane (APTS) to give modified (HA-APTS) product. Functionalized hydroxyapatite (HA-APTS) holds amino groups on their surface that can be further functionalized with other bioactive molecules. The extent of functionalization of HA was studied under three different processing conditions; at room temperature, at 80 °C and under microwave condition (600 W). Three different temperatures have been use for the purpose of comparison between the functionalized products so that we can judge that whether there is any effect of temperature on the final products. In the last we conclude that temperature has no effect. So microwave condition is best to carried out the functionalization in just 5 min. - Highlights: • Extent of functionalization of HA was studied. • Characterized using FTIR spectroscopy, SEM, FESEM, HRTEM, XRD & NMR • n-HA particles were covalently linked with APTS under microwave radiation. • Beneficial from biomedical point of view.

  3. The use of surface-active agents in the preparation and assembly of quantum-sized nanoparticles.

    Science.gov (United States)

    Bognolo, G

    2003-12-01

    This overview summarises the use of surface-active agents for preparation of nanoparticles. It starts with description of the nanotechnology vision. Nanoparticle products are exemplified by using solid-state processes, e.g. for the production of ceramics or catalysts, as well as colloidal processes whereby the use of surface-active agents plays a major role. Several examples are given in the review, e.g. use of coordination ligands and nanoparticle self-assembly. The process of control of nanoparticle shape and its modulation is briefly described and examples are given to demonstrate such control.

  4. Surface Characterization and in situ Protein Adsorption Studies on Carbene-Modified Polymers.

    Science.gov (United States)

    Nelson, Geoffrey W; Parker, Emily M; Singh, Kulveer; Blanford, Christopher F; Moloney, Mark G; Foord, John S

    2015-10-13

    Polystyrene thin films were functionalized using a facile two-step chemical protocol involving carbene insertion followed by azo-coupling, permitting the introduction of a range of chemical functional groups, including aniline, hexyl, amine, carboxyl, phenyl, phosphonate diester, and ethylene glycol. X-ray photoelectron spectroscopy (XPS) confirmed the success of the two-step chemical modification with a grafting density of at least 1/10th of the typical loading density (10(14)-10(15)) of a self-assembled monolayer (SAM). In situ, real-time quartz crystal microbalance with dissipation (QCM-D) studies show that the dynamics of binding of bovine serum albumin (BSA) are different at each modified surface. Mass, viscoelastic, and kinetic data were analyzed, and compared to cheminformatic descriptors (i.e., c log P, polar surface area) typically used for drug discovery. Results show that functionalities may either resist or adsorb BSA, and uniquely influence its adsorption dynamics. It is concluded that carbene-based surface modification can usefully influence BSA binding dynamics in a manner consistent with, and more robust than, traditional systems based on SAM chemistry.

  5. Surface attachment induced production of antimicrobial compounds by marine epiphytic bacteria using modified roller bottle cultivation.

    Science.gov (United States)

    Yan, Liming; Boyd, Kenneth G; Grant Burgess, J

    2002-09-01

    A modified roller bottle culture method elicited the production of antimicrobial compounds from 2 epibiotic marine bacterial strains, EI-34-6 and II-111-5, isolated from the surface of the marine alga Palmaria palmata. These isolates, tentatively identified as Bacillus species, were grown as a biofilm on the surface of nutrient glycerol ferric agar (NGFA) and marine Columbia glycerol agar (MCGA) on the inside of a rolling bottle. The biofilm was shown to be stable, and the cells were difficult to remove from the agar surface. The culture supernatant exhibited a different antibiotic spectrum when the strains were grown using the agar roller bottle method compared with shake flask cultures or nonagar roller bottle cultures. These results suggest that biofilm formation is an important factor in the production of antimicrobial compounds by these 2 strains, and roller bottle cultivation also allowed production of these compounds to be increased. The methodology used here has the potential to allow increased production of useful secondary metabolites such as antibiotics from marine epibiotic bacteria.

  6. The Wear behavior of UHMWPE against Surface Modified CP-Titanium by Thermal Oxidation

    Directory of Open Access Journals (Sweden)

    B.T. Prayoga

    2016-12-01

    Full Text Available The effects of thermal oxidation duration on hardness, roughness, and wettability of the CP-titanium surfaces were investigated in this paper. The thermal oxidation treatment was done at 700 oC for 12-36 hours in an air atmosphere. The wear behavior of the UHMWPE sliding against treated thermal oxidation of the CP-titanium was tested by a pin-on-plate tribometer under lubrication of the solution of 75 % distilled water and 25 % bovine serum. The results showed that the layer of the oxide titanium was formed on the surface after being treated by the thermal oxidation for 12-36 hours. The oxide titanium layer was dominated by rutile form of TiO2, that offers an improvement of hardness and wettability of the CP-titanium surfaces. The average wear factor of the UHMWPE reduced significantly when the sliding against of the CP-titanium was modified by the thermal oxidation, and the lowest average wear factor was reached when the sliding against the 12 hour oxidized CP-titanium counterfaces.

  7. Development of a surface modified silicone-keratoprosthesis with scleral fixation.

    Science.gov (United States)

    von Fischern, T; Langefeld, S; Yuan, L; Völcker, N; Reim, M; Kirchhof, B; Schrage, N F

    1998-01-01

    Many attempts have been made to create artificial corneas. The keratoprostheses currently available do not allow measurements of the intraocular pressure (IOP) and restrict the visual field. The main problem is extrusion due to an insufficient connection between implant and surrounding tissue. It is our aim to create a flexible keratoprosthesis with a wide field optic allowing measurements of the IOP. Surface modification will improve cell adhesion and therefore stability between implant and tissue. The keratoprosthesis is made of silicone rubber. The optical zone is 11 mm in diameter with a thickness of 0.3 mm. The surface modified haptic consists of a scleral rim and 8 branches for scleral fixation. Optical and mechanical qualities were tested by tensile tests, spectrophotometry and topography. A method to produce one-piece silicone keratoprostheses was established. Submicron lathing of the mould led to an excellent optical quality. Spectrophotometry showed high degree of visible and ultraviolet light transmission of the silicone. Mechanical tests revealed high tensile strength and elongation at break which were not impaired by surface modification. The production of a flexible silicone keratoprosthesis with high optical and mechanical properties was accomplished, with possible use as both permanent and temporary keratoprosthesis.

  8. Global land surface climate analysis based on the calculation of a modified Bowen ratio

    Science.gov (United States)

    Han, Bo; Lü, Shihua; Li, Ruiqing; Wang, Xin; Zhao, Lin; Zhao, Cailing; Wang, Danyun; Meng, Xianhong

    2017-05-01

    A modified Bowen ratio (BRm), the sign of which is determined by the direction of the surface sensible heat flux, was used to represent the major divisions in climate across the globe, and the usefulness of this approach was evaluated. Five reanalysis datasets and the results of an offline land surface model were investigated. We divided the global continents into five major BRm zones using the climatological means of the sensible and latent heat fluxes during the period 1980-2010: extremely cold, extremely wet, semi-wet, semi-arid and extremely arid. These zones had BRm ranges of (-∞, 0), (0, 0.5), (0.5, 2), (2, 10) and (10, +∞), respectively. The climatological mean distribution of the Bowen ratio zones corresponded well with the K¨oppen-like climate classification, and it reflected well the seasonal variation for each subdivision of climate classification. The features of climate change over the mean climatological BRm zones were also investigated. In addition to giving a map-like classification of climate, the BRm also reflects temporal variations in different climatic zones based on land surface processes. An investigation of the coverage of the BRm zones showed that the extremely wet and extremely arid regions expanded, whereas a reduction in area was seen for the semi-wet and semi-arid regions in boreal spring during the period 1980-2010. This indicates that the arid regions may have become drier and the wet regions wetter over this period of time.

  9. Primordial germ cell differentiation of nuclear transfer embryonic stem cells using surface modified electroconductive scaffolds.

    Science.gov (United States)

    Eslami-Arshaghi, Tarlan; Vakilian, Saeid; Seyedjafari, Ehsan; Ardeshirylajimi, Abdolreza; Soleimani, Masoud; Salehi, Mohammad

    2017-04-01

    A combination of nanotopographical cues and surface modification of collagen and fibronectin is a potential platform in primordial germ cells (PGCs) differentiation. In the present study, the synergistic effect of nanotopography and surface modification on differentiation of nuclear transfer embryonic stem cells (nt-ESCs) toward PGC lineage was investigated. In order to achieve this goal, poly-anyline (PANi) was mix within poly-L-lactic acid (PLLA). Afterward, the random composite mats were fabricated using PLLA and PANi mix solution. The nanofiber topography notably upregulated the expressions of prdm14, mvh and c-kit compared with tissue culture polystyrene (TCP). Moreover, the combination of nanofiber topography and surface modification resulted in more enhancement of PGCs differentiation compared with non-modified nanofibrous scaffold. Additionally, gene expression results showed that mvh and c-kit were expressed at higher intensity in cells exposed to collagen and fibronectin rather than collagen or fibronectin solitary. These results demonstrated the importance of combined effect of collagen and fibronectin in order to develop a functional extracellular matrix (ECM) mimic in directing stem cell fate and the potential of such biofunctional scaffolds for treatment of infertility.

  10. Electrochemical behaviour and surface conductivity of niobium carbide-modified austenitic stainless steel bipolar plate

    Science.gov (United States)

    Wang, Lixia; Sun, Juncai; Kang, Bin; Li, Song; Ji, Shijun; Wen, Zhongsheng; Wang, Xiaochun

    2014-01-01

    A niobium carbide diffusion layer with a cubic NbC phase surface layer (∼6 μm) and a Nb and C diffusion subsurface layer (∼1 μm) is fabricated on the surface of AISI 304 stainless steel (304 SS) bipolar plate in a proton exchange membrane fuel cell (PEMFC) using plasma surface diffusion alloying. The electrochemical behaviour of the niobium carbide diffusion-modified 304 SS (Nb-C 304 SS) is investigated in simulated PEMFC environments (0.5 M H2SO4 and 2 ppm HF solution at 80 °C). Potentiodynamic, potentiostatic polarisation and electrochemical impedance spectroscopy measurements reveal that the niobium carbide diffusion layer considerably improves the corrosion resistance of 304 SS compared with untreated samples. The corrosion current density of Nb-C 304 SS is maintained at 0.058 μA cm-2 and 0.051 μA cm-2 under simulated anodic and cathodic conditions, respectively. The interfacial contact resistance of Nb-C 304 SS is 8.47 mΩ cm2 at a compaction force of 140 N cm-2, which is significantly lower than that of the untreated sample (100.98 mΩ cm2). Moreover, only a minor increase in the ICR of Nb-C 304 SS occurs after 10 h potentiostatic tests in both cathodic and anodic environments.

  11. Supersmooth and modified surface of sapphire crystals: Formation, characterization, and applications in nanotechnologies

    International Nuclear Information System (INIS)

    Muslimov, A. E.; Asadchikov, V. E.; Butashin, A. V.; Vlasov, V. P.; Deryabin, A. N.; Roshchin, B. S.; Sulyanov, S. N.; Kanevsky, V. M.

    2016-01-01

    The results of studying the state of the surface of sapphire crystals by a complex of methods in different stages of crystal treatment are considered by an example of preparing sapphire substrates with a supersmooth surface. The possibility of purposefully forming regular micro- and nanoreliefs and thin transition layers using thermal and thermochemical impacts are considered. The advantages of sapphire substrates with a modified surface for forming heteroepitaxial CdTe and ZnO semiconductor films and ordered ensembles of gold nanoparticles are described. The results of the experiments on the application of crystalline sapphire as a material for X-ray optical elements are reported. These elements include total external reflection mirrors and substrates for multilayer mirrors, output windows for synchrotron radiation, and monochromators working in the reflection geometry in X-ray spectrometers. In the latter case, the problems of the defect structure of bulk crystals sapphire and the choice of a method for growing sapphire crystals of the highest structural quality are considered.

  12. Study on surface adhesion of Plasma modified Polytetrafluoroethylene hollow fiber membrane

    Science.gov (United States)

    Chen, Jiangrong; Zhang, Huifeng; Liu, Guochang; Guo, Chungang; Lv, Jinglie; Zhangb, Yushan

    2018-01-01

    Polytetrafluoroethylene (PTFE) is popular membrane material because of its excellent thermal stability, chemical stability and mechanical stability. However, the low surface energy and non-sticky property of PTFE present challenges for modification. In the present study, plasma treatment was performed to improve the surface adhesion of PTFE hollow fiber membrane. The effect of discharge voltage, treatment time on the adhesion of PTFE hollow fiber membrane was symmetrically evaluated. Results showed that the plasma treatment method contributed to improve the surface activity and roughness of PTFE hollow fiber membrane, and the adhesion strength depend significantly on discharge voltage, which was beneficial to seepage pressure of PTFE hollow fiber membrane module. The adhesion strength of PTFE membrane by plasma treated at 220V for 3min reached as high as 86.2 N, far surpassing the adhesion strength 12.7 N of pristine membrane. Furthermore, improvement of content of free radical and composition analysis changes of the plasma modified PTFE membrane were investigated. The seepage pressure of PTFE membrane by plasma treated at 220V for 3min was 0.375 MPa, which means that the plasma treatment is an effective technique to improve the adhesion strength of membrane.

  13. Supersmooth and modified surface of sapphire crystals: Formation, characterization, and applications in nanotechnologies

    Science.gov (United States)

    Muslimov, A. E.; Asadchikov, V. E.; Butashin, A. V.; Vlasov, V. P.; Deryabin, A. N.; Roshchin, B. S.; Sulyanov, S. N.; Kanevsky, V. M.

    2016-09-01

    The results of studying the state of the surface of sapphire crystals by a complex of methods in different stages of crystal treatment are considered by an example of preparing sapphire substrates with a supersmooth surface. The possibility of purposefully forming regular micro- and nanoreliefs and thin transition layers using thermal and thermochemical impacts are considered. The advantages of sapphire substrates with a modified surface for forming heteroepitaxial CdTe and ZnO semiconductor films and ordered ensembles of gold nanoparticles are described. The results of the experiments on the application of crystalline sapphire as a material for X-ray optical elements are reported. These elements include total external reflection mirrors and substrates for multilayer mirrors, output windows for synchrotron radiation, and monochromators working in the reflection geometry in X-ray spectrometers. In the latter case, the problems of the defect structure of bulk crystals sapphire and the choice of a method for growing sapphire crystals of the highest structural quality are considered.

  14. Experimental investigation of surface modified EOF steel slag as coarse aggregate in concrete

    Directory of Open Access Journals (Sweden)

    Y.K. Sabapathy

    2017-10-01

    Full Text Available An experimental work was carried out to study the effect of Energy Optimizing Furnace (EOF steel slag as coarse aggregate replacement in concrete. Surface modification of slag was carried out to seal the surface voids of raw slag aggregates. Quarry dust obtained as an extractive waste from the granite stone quarries has been used as a blending material in this work. After several trials, it was found that a mix proportion of 1:6:14 (cement:quarry dust:slag aggregate was the most suitable mix ratio for the surface modification of the slag aggregates. Various mixes of concrete were prepared with different proportions of modified slag (ranging from 0% to 100% as replacements for aggregates. Three grades of concrete (20 MPa, 30 MPa and 40 MPa were used in the investigation and the concrete mixes were evaluated for compressive strength and splitting tensile strength. It was found that the compressive strength improved for 25 percent replacement of natural coarse aggregates. The splitting tensile strength was found to peak at 25 percent replacement of natural aggregates.

  15. Modified PAMAM dendrimer with 4-carbomethoxypyrrolidone surface groups reveals negligible toxicity against three rodent cell-lines

    DEFF Research Database (Denmark)

    Janaszewska, Anna; Ciolkowski, Michal; Wróbel, Dominika

    2013-01-01

    Modification of the surface groups of dendrimers is one of the methods to improve their biocompatibility. This article presents results of experiments related to the toxicity of a modified polyamidoamine (PAMAM) dendrimer of the fourth generation with 4-carbomethoxypyrrolidone surface groups (PAM...

  16. Ligand-Modified Aminobisphosphonate for Linking Proteins to Hydroxyapatite and Bone Surface

    Science.gov (United States)

    Ehrick, Robin S.; Capaccio, Marcello; Puleo, David A.; Bachas, Leonidas G.

    2011-01-01

    An increase in bone resorption is one of the main symptoms of osteoporosis, a disease that affects more and more individuals every day. Bisphosphonates are known to inhibit bone resorption, and thus are being used as a treatment for osteoporosis. Aminobisphosphonates present a functionality that can be easily used for conjugation to other molecules, such as peptides, proteins, and ligands for protein recognition. In this study, an aminobisphosphonate conjugated with biotin was used as a model linker for protein attachment to bone. With this system, the interaction of biotinylated aminobisphosphonate with hydroxyapatite, a major mineral component of bone, was investigated. Quantification of the binding of aminobisphosphonate to hydroxyapatite was performed using a fluorescently labeled antibody for biotin. Additionally, the interaction of the biotinylated aminobisphosphonate with multiple treatments of cortical bone from the mid-shaft of a cow femur was studied. It was demonstrated that modified aminobisphosphonate reagents can bind hydroxyapatite and bone at high levels, while the biotin functionality is free to be recognized by the fluorescently labeled anti-biotin antibody, suggesting that modified aminobisphosphonates could be used to link other peptides or proteins to the bone surface. PMID:18001076

  17. Modified neural dynamic surface approach to output feedback of MIMO nonlinear systems.

    Science.gov (United States)

    Sun, Guofa; Li, Dongwu; Ren, Xuemei

    2015-02-01

    We report an adaptive output feedback dynamic surface control (DSC), maintaining the prescribed performance, for a class of uncertain nonlinear systems with multiinput and multioutput. Designing neural network observers and modifying the DSC method achieves several control objectives. First, to achieve output feedback control, the finite-time echo state networks (ESN) observer with fast convergence is designed to obtain the online system states. Thus, the immeasurable states in traditional state feedback control are estimated and the unknown functions are approximated by ESN. Then, a modified DSC approach is developed by introducing a high-order sliding mode differentiator to replace the first-order filter in each step. Thus, the effect of filter performance on closed-loop stability is reduced. Furthermore, the input to state stability guarantees that all signals of the whole closed-loop system are semiglobally uniformly ultimately bounded. Specifically, the performance functions make the tracking errors converge to a compact set around equilibrium. Two numerical examples illustrated the proposed control scheme with satisfactory results.

  18. Combined slurry and cavitation erosion resistance of surface modified SS410 stainless steel

    Science.gov (United States)

    Amarendra, H. J.; Pratap, M. S.; Karthik, S.; Punitha Kumara, M. S.; Rajath, H. C.; Ranjith, H.; Shubhatunga, S. V.

    2018-03-01

    Slurry erosion and combined slurry and cavitation erosion resistance of thermal spray coatings are studied and compared with the as-received martensitic stainless steel material. 70Ni-Cr coatings are deposited on SS 410 material through plasma thermal spray process. The synergy effect of the combined slurry and cavitation erosion resistance of plasma thermal spray coatings were investigated in a slurry pot tester in the presence of bluff bodies known as Cavitation Inducers. Results showed the combined slurry and cavitation erosion resistance of martensitic stainless steel - 410 can be improved by plasma thermal spray coating. It is observed that the plasma spray coated specimens are better erosion resistant than the as- received material, subjected to erosion test under similar conditions. As-received and the surface modified steels are mechanically characterized for its hardness, bending. Morphological studies are conducted through scanning electron microscope.

  19. A modified Poisson-Boltzmann surface excess calculation with a field dependent dielectric constant

    International Nuclear Information System (INIS)

    Gordillo, G.J.; Molina, F.V.; Posadas, D.

    1990-01-01

    The Unequal Radius Modified Gouy-Chapman (URMGC) was applied to mixtures of electrolytes. It was considered that the two anions, (1) and (2), have different radius, r 1 and r 2 , being r 2 smaller than r 1 . The dielectric constant was taken as a function of the electric field, using the theoretical Booth equation, or as a linear dependence varying between 6 and 78 when r 2 1 . The results show that the surface excess of anion 2 is much greater than the one predicted by Gouy-Chapman theory when the proportion of 2 increases in the mixture, while both the other anion and the cation show negative deviation. This effect is more evident in mixtures than in the case of single electrolytes, and has a maximum for a composition that depends on the chosen parameters for the model. (Author) [es

  20. Preparation and characterization of gadolinium-loaded PLGA particles surface modified with RGDS for the detection of thrombus

    Directory of Open Access Journals (Sweden)

    Zhang Y

    2013-10-01

    Full Text Available Yu Zhang,1 Jun Zhou,1 Dajing Guo,1 Meng Ao,2 Yuanyi Zheng,2 Zhigang Wang21Department of Radiology, the Second Affiliated Hospital of Chongqing Medical University, Chongqing, People’s Republic of China; 2Institute of Ultrasound Imaging, Department of Ultrasound, the Second Affiliated Hospital of Chongqing Medical University, Chongqing, People’s Republic of ChinaAbstract: Thrombotic disease is a leading cause of death and disability worldwide. The development of magnetic resonance molecular imaging provides potential promise for early disease diagnosis. In this study, we explore the preparation and characterization of gadolinium (Gd-loaded poly (lactic-co-glycolic acid (PLGA particles surface modified with the Arg-Gly-Asp-Ser (RGDS peptide for the detection of thrombus. PLGA was employed as the carrier-delivery system, and a double emulsion solvent-evaporation method (water in oil in water was used to prepare PLGA particles encapsulating the magnetic resonance contrast agent Gd diethylenetriaminepentaacetic acid (DTPA. To synthesize the Gd-PLGA/chitosan (CS-RGDS particles, carbodiimide-mediated amide bond formation was used to graft the RGDS peptide to CS to form a CS-RGDS film that coated the surface of the PLGA particles. Blank PLGA, Gd-PLGA, and Gd-PLGA/CS particles were fabricated using the same water in oil in water method. Our results indicated that the RGDS peptide successfully coated the surface of the Gd-PLGA/CS-RGDS particles. The particles had a regular shape, smooth surface, relatively uniform size, and did not aggregate. The high electron density of the Gd-loaded particles and a translucent film around the particles coated with the CS and CS-RGDS films could be observed by transmission electron microscopy. In vitro experiments demonstrated that the Gd-PLGA/CS-RGDS particles could target thrombi and could be imaged using a clinical magnetic resonance scanner. Compared with the Gd-DTPA solution, the longitudinal relaxation time of

  1. Surface modified natural zeolite as a carrier for sustained diclofenac release: A preliminary feasibility study.

    Science.gov (United States)

    de Gennaro, Bruno; Catalanotti, Lilia; Cappelletti, Piergiulio; Langella, Alessio; Mercurio, Mariano; Serri, Carla; Biondi, Marco; Mayol, Laura

    2015-06-01

    In view of zeolite potentiality as a carrier for sustained drug release, a clinoptilolite-rich rock from California (CLI_CA) was superficially modified with cetylpyridinium chloride and loaded with diclofenac sodium (DS). The obtained surface modified natural zeolites (SMNZ) were characterized by confocal scanning laser microscopy (CLSM), powder X-ray diffraction (XRPD) and laser light scattering (LS). Their flowability properties, drug adsorption and in vitro release kinetics in simulated intestinal fluid (SIF) were also investigated. CLI_CA is a Na- and K-rich clinoptilolite with a cationic exchange ability that fits well with its zeolite content (clinoptilolite=80 wt%); the external cationic exchange capacity is independent of the cationic surfactant used. LS and CLSM analyses have shown a wide distribution of volume diameters of SMNZ particles that, along with their irregular shape, make them cohesive with scarce flow properties. CLSM observation has revealed the localization of different molecules in/on SMNZ by virtue of their chemical nature. In particular, cationic and polar probes prevalently localize in SMNZ bulk, whereas anionic probes preferentially arrange themselves on SMNZ surface and the loading of a nonpolar molecule in/on SMNZ is discouraged. The adsorption rate of DS onto SMNZ was shown by different kinetic models highlighting the fact that DS adsorption is a pseudo-second order reaction and that the diffusion through the boundary layer is the rate-controlling step of the process. DS release in an ionic medium, such as SIF, can be sustained for about 5h through a mechanism prevalently governed by anionic exchange with a rapid final phase. Copyright © 2015 Elsevier B.V. All rights reserved.

  2. The surface characteristics of hyperbranched polyamide modified corncob and its adsorption property for Cr(VI)

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Hai, E-mail: linhai@ces.ustb.edu.cn [School of Energy and Environmental Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Beijing Key Laboratory on Resource-oriented Treatment of Industrial Pollutants, Beijing 100083 (China); Han, Shaoke; Dong, Yingbo; He, Yinhai [School of Energy and Environmental Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Beijing Key Laboratory on Resource-oriented Treatment of Industrial Pollutants, Beijing 100083 (China)

    2017-08-01

    Highlights: • An anion adsorbent was synthesized by hyperbranched polyamide modified corncob (HPMC). • The surface characteristics of samples (RCC, HPMC, HPMC-Cr) were studied. • Langmuir isotherm provided more fit and maximum adsorption capacity was 131.6 mg/g. • The adsorption process was chemisorption, controlled by intra-particle diffusion and film diffusion. • Adsorption is fast, stable, spontaneous and endothermic. - Abstract: A low-cost anion adsorbent for Cr(VI) effectively removing was synthesized by hyperbranched polyamide modified corncob (HPMC). Samples were characterized by Brunauer–Emmett–Teller (BET) surface area analysis, field-emission scanning electron microscopy (FE-SEM) with energy-dispersive X-ray spectroscopy, Fourier transform infrared (FTIR) and zeta potential analysis. Kinetics, isotherms and thermodynamics studies of HPMC for Cr(VI) adsorption were investigated in batch static experiments, in the temperature range of 25–45 °C, pH = 2.0. Results showed that the adsorption was rapid and stable, with the uptake capacity higher than 80% after 30 min. Adsorption behavior and rate-controlling mechanisms were analyzed using three kinetic models (pseudo-first order, pseudo-second order, intra-particle kinetic model). Kinetic studies showed that the adsorption of HPMC to Cr(VI) relied the pseudo-second-order model, and controlled both by the intra-particle diffusion and film diffusion. Equilibrium data was tested by Langmuir and Freundlich adsorption isotherm models. Langmuir model was more suitable to indicate a homogeneous distribution of active sites on HPMC and monolayer adsorption. The maximum adsorption capacity from the Langmuir model, q{sub max}, was 131.6 mg/g at pH 2.0 and 45 °C for HPMC. Thermodynamic parameters revealed spontaneous and endothermic nature of the Cr(VI) adsorption onto HPMC.

  3. Modifying surface properties of KIT-6 zeolite with Ni and V for enhancing catalytic CO methanation

    Science.gov (United States)

    Cao, Hong-Xia; Zhang, Jun; Guo, Cheng-Long; Chen, Jingguang G.; Ren, Xiang-Kun

    2017-12-01

    The surface of the KIT-6 zeolite was modified with different amounts of Ni and V to promote the catalytic properties for CO methanation. A series of xNi-yV/KIT-6 with various Ni and V contents were prepared by the incipient-wetness impregnation method. The modified surfaces were characterized using N2 adsorption-desorption, Brunauer-Emmett-Teller (BET), X-ray diffraction (XRD), hydrogen temperature-programmed reduction (H2-TPR), Fourier transformed infrared spectroscopy (FT-IR), Raman, X-ray photoelectron spectroscopy (XPS), transmission electron microscope (TEM), and energy-dispersive X-ray spectroscopy (EDX), respectively. The characterization results illustrated that the modification of V species was able to significantly promote low-temperature catalytic performance below 350 °C compared to that of unmodified Ni/KIT-6, which was likely due to an increase in the H2 uptake accompanied by enhanced CO dissociation derived from stronger electron transfer from V species to Ni0. Correspondingly, the xNi-yV/KIT-6 catalysts exhibited a distinct enhancement in CO conversion, CH4 selectivity and CH4 yield over unmodified Ni/KIT-6. Among all catalysts, 20Ni-2V/KIT-6 showed the best catalytic performance, corresponding to nearly 100% CO conversion and 85% CH4 yield at a low temperature of 300 °C. Furthermore, 20Ni-2V/KIT-6 presented enhanced coking-resistant and anti-sintering properties during a 60h-lifetime test at 500 °C and 1 atm with a high weight hourly space velocity (WHSV) of 60000 ml/g/h.

  4. Improvement of epoxy resin properties by incorporation of TiO2 nanoparticles surface modified with gallic acid esters

    International Nuclear Information System (INIS)

    Radoman, Tijana S.; Džunuzović, Jasna V.; Jeremić, Katarina B.; Grgur, Branimir N.; Miličević, Dejan S.; Popović, Ivanka G.; Džunuzović, Enis S.

    2014-01-01

    Highlights: • Nanocomposites of epoxy resin and TiO 2 nanoparticles surface modified with gallates. • The T g of epoxy resin was increased by incorporation of surface modified TiO 2 . • WVTR of epoxy resin decreased in the presence of surface modified TiO 2 nanoparticles. • WVTR of nanocomposites was reduced with increasing gallates hydrophobic chain length. • Modified TiO 2 nanoparticles react as oxygen scavengers, inhibiting steel corrosion. - Abstract: Epoxy resin/titanium dioxide (epoxy/TiO 2 ) nanocomposites were obtained by incorporation of TiO 2 nanoparticles surface modified with gallic acid esters in epoxy resin. TiO 2 nanoparticles were obtained by acid catalyzed hydrolysis of titanium isopropoxide and their structural characterization was performed by X-ray diffraction and transmission electron microscopy. Three gallic acid esters, having different hydrophobic part, were used for surface modification of the synthesized TiO 2 nanoparticles: propyl, hexyl and lauryl gallate. The gallate chemisorption onto surface of TiO 2 nanoparticles was confirmed by Fourier transform infrared and ultraviolet–visible spectroscopy, while the amount of surface-bonded gallates was determined using thermogravimetric analysis. The influence of the surface modified TiO 2 nanoparticles, as well as the length of hydrophobic part of the gallate used for surface modification of TiO 2 nanoparticles, on glass transition temperature, barrier, dielectric and anticorrosive properties of epoxy resin was investigated by differential scanning calorimetry, water vapor transmission test, dielectric spectroscopy, electrochemical impedance spectroscopy and polarization measurements. Incorporation of surface modified TiO 2 nanoparticles in epoxy resin caused increase of glass transition temperature and decrease of the water vapor permeability of epoxy resin. The water vapor transmission rate of epoxy/TiO 2 nanocomposites was reduced with increasing hydrophobic part chain length of

  5. Role of surface chemistry in modified ACF (activated carbon fiber)-catalyzed peroxymonosulfate oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Shiying, E-mail: ysy@ouc.edu.cn [Key Laboratory of Marine Environment and Ecology, Ministry of Education, Qingdao 266100 (China); College of Environmental Science and Engineering, Ocean University of China, Qingdao 266100 (China); Shandong Provincial Key Laboratory of Marine Environment and Geological Engineering (MEGE), Qingdao 266100 (China); Li, Lei [College of Environmental Science and Engineering, Ocean University of China, Qingdao 266100 (China); Xiao, Tuo [College of Environmental Science and Engineering, Ocean University of China, Qingdao 266100 (China); China City Environment Protection Engineering Limited Company, Wuhan 430071 (China); Zheng, Di; Zhang, Yitao [College of Environmental Science and Engineering, Ocean University of China, Qingdao 266100 (China)

    2016-10-15

    Highlights: • ACF can efficiently activate peroxymonosulfate to degrade organic pollutants. • Basic functional groups may mainly increase the adsorption capacity of ACF. • C1, N1, N2 have promoting effect on the ACF catalyzed PMS oxidation. • Modification by heat after nitric acid is also a way of ACF regeneration. - Abstract: A commercial activated carbon fiber (ACF-0) was modified by three different methods: nitration treatment (ACF-N), heat treatment (ACF-H) and heat treatment after nitration (ACF-NH), and the effects of textural and chemical properties on the ability of the metal-free ACF-catalyzed peroxymonosulfate (PMS) oxidation of Reactive Black 5 (RB5), an azo dye being difficultly adsorbed onto ACF, in aqueous solution were investigated in this work. Surface density of functional groups, surface area changes, surface morphology and the chemical state inside ACF samples were characterized by Boehm titration, N{sub 2} adsorption, scanning electron microscopy in couple with energy dispersive spectroscopy (SEM-EDS) and X-ray photoelectron spectroscopy (XPS), respectively. XPS spectra deconvolution was applied to figure out the importance of surface nitrogen-containing function groups. We found that π-π, pyridine and amine have promoting effect on the catalytic oxidation while the −NO{sub 2} has inhibitory effect on the ACF/PMS systems for RB5 destroy. Sustainability and renewability of the typical ACF-NH for catalytic oxidation of RB5 were also discussed in detail. Information about our conclusions are useful to control and improve the performance of ACF-catalyzed PMS oxidation for organic pollutants in wastewater treatment.

  6. Biological responses to M13 bacteriophage modified titanium surfaces in vitro.

    Science.gov (United States)

    Sun, Yuhua; Li, Yiting; Wu, Baohua; Wang, Jianxin; Lu, Xiong; Qu, Shuxin; Weng, Jie; Feng, Bo

    2017-08-01

    Phage-based materials have showed great potential in tissue engineering application. However, it is unknown what inflammation response will happen to this kind of materials. This work is to explore the biological responses to M13 bacteriophage (phage) modified titanium surfaces in vitro from the aspects of their interaction with macrophages, osteoblasts and mineralization behavior. Pretreated Ti surface, Ti surfaces with noncrosslinked phage film (APP) and crosslinked phage film (APPG) were compared. Phage films could limit the macrophage adhesion and activity due to inducing adherent-cell apoptosis. The initial inflammatory activity (24h) caused by phage films was relatively high with more production of TNF-α, but in the later stage (7-10days) inflammatory response was reduced with lower TNF-α, IL-6 and higher IL-10. In addition, phage films improved osteoblast adhesion, differentiation, and hydroapatite (HA)-forming via a combination of topographical and biochemcial cues. The noncrosslinked phage film displayed the best immunomodulatory property, osteogenic activity and HA mineralization ability. This work provides better understanding of inflammatory and osteogenetic activity of phage-based materials and contributes to their future application in tissue engineering. In vivo, the bone and immune cells share a common microenvironment, and are being affected by similar cytokines, signaling molecules, transcription factors and membrane receptors. Ideal implants should cause positive biological response, including adequate and appropriate inflammatory reaction, well-balanced bone formation and absorption. Phage-based materials have showed great potential in tissue engineering application. However, at present it is unknown what inflammation response will happen to this kind of materials. A good understanding of the immune response possibly induced by phage-based materials is needed. This work studied the osteoimmunomodulation property of phage films on titanium

  7. Solubilizing properties of new surface-active agents, products of catalytic oxyethylation of cholic acid.

    Science.gov (United States)

    Kołodziejczyk, Michał Krzysztof; Nachajski, Michal Jakub; Lukosek, Marek; Zgoda, Marian Mikołaj

    2013-01-01

    Solubilizing properties of aqueous solutions of a series of surface-active agents, products of oxyethylation of cholic acid, were examined in the present study. The content of oxyethylated segments determined by means of the 1H NMR method enabled the verification of the molecular mass of surfactants along with the calculation of the structural hydrophilic-lipophilic balance (HLB), the solubility parameter delta1/2, and the required solubility level of balance HLB(R). Viscosimetric measurements enabled the calculation of the limiting viscosity number, the content-average molecular mass, the effective volume, the hydrodynamic radius of the surfactant micelle and their equilibrium adducts with rutin, diclofenac and loratadine (BCS Class II and III). By means of the spectrophotometric method (UV) the amount of the solubilized diclofenac, loratadine and rutin (rutoside) was determined in the equilibrium system (saturated solution) in the environment of aqueous solutions of cholic acid derivatives of n(TE) = 20-70. The obtained results serve as a basis for determining the solubilization mechanism of lipophilic therapeutic products and indirectly for estimating the influence of the above process on pharmaceutical as well as biological availability of a micellar adduct from model drug forms (Lindbladt lithogenolitic index).

  8. Reusable ultrasonic tissue mimicking hydrogels containing nonionic surface-active agents for visualizing thermal lesions.

    Science.gov (United States)

    Park, Seong Keun; Guntur, S R Anjaneya Reddy; Lee, Kang Il; Paeng, Dong-Guk; Choi, Min Joo

    2010-01-01

    The present study aims to identify a new recipe for reusable tissue mimicking phantoms that allows the optical visualization of thermal lesions produced in various applications of therapeutic ultrasound where thermal mechanisms are important. The phantom was made of polyacrylamide hydrogel containing a nonionic surface-active agent (NiSAA) as a temperature-sensitive indicator. Threshold temperature above which a thermal lesion is regarded to be formed in the phantom is controlled by selecting an NiSAA. In the present study, three NiSAAs of polyoxyethylene alkyl ether series with nominal clouding points of 66 ( degrees )C, 70 ( degrees )C, and 80 ( degrees ) C were chosen. Test phantoms were prepared with polyacrylamide hydrogel, corn syrup and NiSAAs [5% (w/v)]. Key acoustic properties of the three NiSAA hydrogels were found to be similar to those of human liver. The phantoms were optically transparent at room temperature (25 ( degrees ) C) and became opaque after exceeding the clouding points. The transparency was recovered on cooling, although the system demonstrated hysteresis. The phantoms were tested both in their ability to provide visualization of thermal lesions produced by high-intensity focused ultrasound and also to examine any characteristic differences in the shape of the lesions formed at different threshold temperatures. The present study suggests that the NiSAA polyacrylamide hydrogel will be of a practical use in quality assurance in various applications of therapeutic ultrasound where thermal mechanisms are important.

  9. DNA microarrays on ultraviolet-modified surfaces for speciation of bacteria.

    Science.gov (United States)

    Liu, Yanyang; He, Jianzhong; Yang, Kun-Lin

    2014-02-15

    In this study, we report an approach to activate inert hydrocarbon monolayers with ultraviolet (UV) light to fabricate DNA microarrays. Unlike traditional microarrays that require reactive functional groups on the surface, our DNA microarray is built on an inert layer of N,N-dimethyl-N-octadecyl(3-aminopropyl)trimethoxysilyl chloride silane (DMOAP). This layer is activated by UV (254 nm) just prior to the immobilization of oligonucleotide probes. Our X-ray photoelectron spectroscopy (XPS) results show that new functional groups such as alcohol (C--O), aldehyde (C=O), and carboxylic acid (O--C=O) form on the surface after the UV exposure. Among them, aldehyde groups are responsible for the immobilization of amine-label oligonucleotides. By using this approach, we further optimize UV exposure time and oligonucleotide concentration and also reduce agent concentration to achieve a high density of immobilized oligonucleotides up to 0.16 pmol/mm². As a proof of concept, we demonstrate that this microarray can be used for differentiation of different Clostridium species such as Clostridium acetobutylicum, Clostridium butylicum, and Clostridium beijerinkii. Copyright © 2013 Elsevier Inc. All rights reserved.

  10. Growth and Functionality of Cells Cultured on Conducting and Semi-Conducting Surfaces Modified with Self-Assembled Monolayers (SAMs

    Directory of Open Access Journals (Sweden)

    Rajendra K. Aithal

    2016-02-01

    Full Text Available Bioengineering of dermal and epidermal cells on surface modified substrates is an active area of research. The cytotoxicity, maintenance of cell phenotype and long-term functionality of human dermal fibroblast (HDF cells on conducting indium tin oxide (ITO and semi-conducting, silicon (Si and gallium arsenide (GaAs, surfaces modified with self-assembled monolayers (SAMs containing amino (–NH2 and methyl (–CH3 end groups have been investigated. Contact angle measurements and infrared spectroscopic studies show that the monolayers are conformal and preserve their functional end groups. Morphological analyses indicate that HDFs grow well on all substrates except GaAs, exhibiting their normal spindle-shaped morphology and exhibit no visible signs of stress or cytoplasmic vacuolation. Cell viability analyses indicate little cell death after one week in culture on all substrates except GaAs, where cells died within 6 h. Cells on all surfaces proliferate except on GaAs and GaAs-ODT. Cell growth is observed to be greater on SAM modified ITO and Si-substrates. Preservation of cellular phenotype assessed through type I collagen immunostaining and positive staining of HDF cells were observed on all modified surfaces except that on GaAs. These results suggest that conducting and semi-conducting SAM-modified surfaces support HDF growth and functionality and represent a promising area of bioengineering research.

  11. Use of Adjuvant Bisphosphonates and Other Bone-Modifying Agents in Breast Cancer: A Cancer Care Ontario and American Society of Clinical Oncology Clinical Practice Guideline.

    Science.gov (United States)

    Dhesy-Thind, Sukhbinder; Fletcher, Glenn G; Blanchette, Phillip S; Clemons, Mark J; Dillmon, Melissa S; Frank, Elizabeth S; Gandhi, Sonal; Gupta, Rasna; Mates, Mihaela; Moy, Beverly; Vandenberg, Ted; Van Poznak, Catherine H

    2017-06-20

    Purpose To make recommendations regarding the use of bisphosphonates and other bone-modifying agents as adjuvant therapy for patients with breast cancer. Methods Cancer Care Ontario and ASCO convened a Working Group and Expert Panel to develop evidence-based recommendations informed by a systematic review of the literature. Results Adjuvant bisphosphonates were found to reduce bone recurrence and improve survival in postmenopausal patients with nonmetastatic breast cancer. In this guideline, postmenopausal includes patients with natural menopause or that induced by ovarian suppression or ablation. Absolute benefit is greater in patients who are at higher risk of recurrence, and almost all trials were conducted in patients who also received systemic therapy. Most studies evaluated zoledronic acid or clodronate, and data are extremely limited for other bisphosphonates. While denosumab was found to reduce fractures, long-term survival data are still required. Recommendations It is recommended that, if available, zoledronic acid (4 mg intravenously every 6 months) or clodronate (1,600 mg/d orally) be considered as adjuvant therapy for postmenopausal patients with breast cancer who are deemed candidates for adjuvant systemic therapy. Further research comparing different bone-modifying agents, doses, dosing intervals, and durations is required. Risk factors for osteonecrosis of the jaw and renal impairment should be assessed, and any pending dental or oral health problems should be dealt with prior to starting treatment. Data for adjuvant denosumab look promising but are currently insufficient to make any recommendation. Use of these agents to reduce fragility fractures in patients with low bone mineral density is beyond the scope of the guideline. Recommendations are not meant to restrict such use of bone-modifying agents in these situations. Additional information at www.asco.org/breast-cancer-adjuvant-bisphosphonates-guideline , www.asco.org/guidelineswiki , https://www.cancercareontario.ca/guidelines-advice/types-of-cancer/breast .

  12. Dynamic shear rheology of colloidal suspensions of surface-modified silica nanoparticles in PEG

    Science.gov (United States)

    Swarna; Pattanayek, Sudip Kumar; Ghosh, Anup Kumar

    2018-03-01

    The present work illustrates the effect of surface modification of silica nanoparticles (500 nm) with 3-(glycidoxypropyl)trimethoxy silane which was carried out at different reaction times. The suspensions prepared from modified and unmodified silica nanoparticles were evaluated for their shear rate-dependent viscosity and strain-frequency-dependent modulus. The linear viscoelastic moduli, viz., storage modulus and loss modulus, were compared with those of nonlinear moduli. The shear-thickened suspensions displayed strain thinning at low-frequency smaller strains and a strong strain overshoot at higher strains, characteristics of a continuous shear thickening fluids. The shear-thinned suspension, conversely, exhibited a strong elastic dominance at smaller strains, but at higher strains, its strain softened observed in the steady shear viscosity plot indicating characteristics of yielding material. Considering higher order harmonic components, the decomposed elastic and viscous stress revealed a pronounced elastic response up to 10% strain and a high viscous damping at larger strains. The current work is one of a kind in demonstrating the effect of silica surface functionalization on the linear and nonlinear viscoelasticity of suspensions showing a unique rheological fingerprint. The suspensions can thus be predicted through rheological studies for their applicability in energy absorbing and damping materials with respect to their mechanical properties.

  13. Surface modified zeolite-based granulates for the sustained release of diclofenac sodium.

    Science.gov (United States)

    Serri, Carla; de Gennaro, Bruno; Quagliariello, Vincenzo; Iaffaioli, Rosario Vincenzo; De Rosa, Giuseppe; Catalanotti, Lilia; Biondi, Marco; Mayol, Laura

    2017-03-01

    In this study, a granulate for the oral controlled delivery of diclofenac sodium (DS), an anionic sparingly soluble nonsteroidal anti-inflammatory drug, has been realized by wet granulation, using a surface modified natural zeolite (SMNZ) as an excipient. The surface modification of the zeolite has been achieved by means of a cationic surfactant, so as to allow the loading of DS through ionic interaction and bestow a control over the drug release mechanism. The granules possessed a satisfactory dosage uniformity, a flowability suitable for an oral dosage form manufacturing, along with a sustained drug release up to 9h, driven by both ion exchange and transport kinetics. Furthermore, the obtained granulate did not elicit a significant cytotoxicity and could also induce a prolonged anti-inflammatory effect on RAW264.7 cells. Taking also into account that natural zeolites are generally abundant and economic, SMNZ can be considered as an attracting alternative excipient for the production of granules with sustained release features. Copyright © 2016 Elsevier B.V. All rights reserved.

  14. Surface Layers of Zr-18%Nb Alloy Modified by Ultrasonic Impact Treatment: Microstructure, Hardness and Corrosion

    Science.gov (United States)

    Khripta, N. I.; Karasevska, O. P.; Mordyuk, B. N.

    2017-11-01

    Near-surface layers in Zr-18%Nb alloy were modified using ultrasonic impact treatment (UIT). The effects of the UIT processing time on a microstructural formation, omega/alpha precipitations, microhardness and corrosion are analyzed. XRD analysis, TEM and SEM observations and EDX characterization allow establishing the links between the microstructure, microhardness and corrosion behavior of the surface layers formed. At the strain extent up to e ≈ 0.3, structural formation occurs under influence of deformation induced heating, which facilitates omega precipitation in beta phase and mechanically induced oxygen transport and oxide formation. XRD analysis reveals moderate compressive residual stresses (- 160 MPa) and pronounced {110} texture after the UIT process. Generation of dislocations and hindering of their movement by nanoscale omega precipitates manifest themselves as the broadening of diffraction peaks occurred mainly owing to the lattice microstrains, and they provide marked strain hardening. The enhanced anticorrosion properties of Zr-18%Nb alloy in saline solution were concluded to be a result of the formation of a protective oxide film, {110} texture and compressive stresses.

  15. Polysiloxane surface modified with bipyrazolic tripodal receptor for quantitative lead adsorption

    Energy Technology Data Exchange (ETDEWEB)

    Radi, Smaail, E-mail: radi_smaail@yahoo.fr [Laboratoire de Chimie Organique, Macromoleculaire et Produits Naturels, Equipe de Chimie Bio-organique et Macromoleculaire, Unite Associee au CNRST URAC 25, Departement de Chimie, Faculte des Sciences, Universite Med I, BP 524, 60 000 Oujda (Morocco); Tighadouini, Said; Toubi, Yahya [Laboratoire de Chimie Organique, Macromoleculaire et Produits Naturels, Equipe de Chimie Bio-organique et Macromoleculaire, Unite Associee au CNRST URAC 25, Departement de Chimie, Faculte des Sciences, Universite Med I, BP 524, 60 000 Oujda (Morocco); Bacquet, Maryse [Universite des Sciences et Technologies de Lille, UMET: Unite Materiaux et Transformations UMR8207, Equipe Ingenierie des Systemes Polymeres, Batiment C6 salle 119-59655 Villeneuve d' Ascq (France)

    2011-01-15

    A new silica gel compound modified N,N-bis(3,5-dimethylpyrazol-1-ylmethyl) amine (SiN{sub 2}Pz) was synthesized and characterized by elemental analysis, FT-IR, {sup 13}C NMR of the solid state, nitrogen adsorption-desorption isotherm, BET surface area and BJH pore sizes. The new surface exhibits good chemical and thermal stability determined by thermogravimetry curves (TGA). The effect of pH and stirring time on the adsorption of Pb(II) were studied. The process of metal retention was followed by batch method and the optimum pH value for the quantitative adsorption of this toxic metal ion was 7. At this pH value, the new functionalized polysiloxane presents further improvements and shows higher affinity (123 mg of Pb{sup 2+}/g of silica) for the effective adsorption of Pb(II) compared to others described sorbents. The extracted amounts of Pb(II) were determined by atomic absorption measurements.

  16. Polymer chain length effects on fibroblast attachment on nylon-3-modified surfaces.

    Science.gov (United States)

    Liu, Runhui; Masters, Kristyn S; Gellman, Samuel H

    2012-04-09

    Nylon-3 polymers have a polyamide backbone reminiscent of that found in proteins (β- vs α-amino acid residues, respectively), which makes these materials interesting for biological applications. Because of the versatility of the ring-opening polymerization process and the variety of β-lactam starting materials available, the structure of nylon-3 copolymers is highly amenable to alteration. A previous study showed that relatively subtle changes in the structure or ratio of hydrophobic and cationic subunits that comprise these polymers can result in significant changes in the ability of nylon-3-bearing surfaces to support cell adhesion and spreading. In the present study, we have exploited the highly tailorable nature of these polymers to synthesize new versions possessing a wide range of chain lengths, with the intent of optimizing these materials for use as cell-supportive substrates. We find that longer nylon-3 chains lead to better fibroblast attachment on modified surfaces and that at the optimal chain lengths less hydrophobic subunits are superior. The best polymers we identified are comparable to an RGD-containing peptide in supporting fibroblast attachment. The results described here will help to focus future efforts aimed at refining nylon-3 copolymer substrates for specific tissue engineering applications.

  17. Characterization of a surface modified carbon cryogel and a carbon supported Pt catalyst

    Directory of Open Access Journals (Sweden)

    BILJANA M. BABIĆ

    2007-08-01

    Full Text Available A carbon cryogel, synthesized by carbonization of a resorcinol/formaldehyde cryogel and oxidized in nitric acid, was used as catalyst support for Pt nano-particles. The Pt/C catalyst was prepared by a modified polyol synthesis method in an ethylene glycol (EG solution. Characterization by nitrogen adsorption showed that the carbon cryogel support and the Pt/C catalyst were mesoporous materials with high specific surface areas (SBET > 400 m2 g-1 and large mesoporous volumes. X-Ray diffraction of the catalyst demonstrated the successful reduction of the Pt precursor to metallic form. TEM Images of the Pt/C catalyst and Pt particle size distribution showed that the mean Pt particle size was about 3.3 nm. Cyclic voltammetry (CV experiments at various scan rates (from 2 to 200 mV s-1 were performed in 0.5 mol dm-3 HClO4 solution. The large capacitance of the oxidized carbon cryogel electrode, which arises from a combination of the double-layer capacitance and pseudocapacitance, associated with the participation of surface redox-type reactions was demonstrated. For the oxidized carbon cryogel, the total specific capacitance determined by 1/C vs. ν0.5 extrapolation method was found to be 386 F g-1. The hydrogen oxidation reaction at the investigated Pt/C catalyst proceeded as an electrochemically reversible, two-electron direct discharge reaction.

  18. Effect of temperature, viscosity and surface tension on gelatine structures produced by modified 3D printer

    Science.gov (United States)

    Kalkandelen, C.; Ozbek, B.; Ergul, N. M.; Akyol, S.; Moukbil, Y.; Oktar, F. N.; Ekren, N.; Kılıc, O.; Kılıc, B.; Gunduz, O.

    2017-12-01

    In the present study, gelatine scaffolds were manufactured by using modified 3D (3 Dimensional) printing machine and the effect of different parameters on scaffold structure were investigated. Such as; temperature, viscosity and surface tension of the gelatine solutions. The varying of gelatine solutions (1, 3, 5, 10, 15 and 20 wt.%) were prepared and characterized. It has been detected that, viscosity of those solutions were highly influenced by temperature and gelatine concentration. Specific CAD (Computer Assistant Design) model which has 67% porosity and original design were created via computer software. However, at high temperatures gelatine solutions caused like liquid but at the lower temperatures were observed the opposite behaviour. In addition to that, viscosity of 1,3,5 wt.% solutions were not enough to build a structure and 20 wt.% gelatine solution too hard to handle, because of the sudden viscosity changes with temperature. Even though, scaffold of the 20 wt.% gelatine solution printed hardly but it was observed the best printed solutions, which were 10 and 15 wt.% gelatine solutions. As a result, 3D printing of gelatine were found the values of the best temperature, viscosity, surface tension and gelatine concentration such as 25-35 °C, 36-163 cP, 46-59 mN/m and 15 wt.% gelatine concentration respectively.

  19. Application of acid modified polyurethane foam surface for detection and removing of organochlorine pesticides from wastewater.

    Science.gov (United States)

    Moawed, E A; Radwan, A M

    2017-02-15

    The commercial polyurethane foam was acid modified to get an inexpensive adsorbent (AM-PUF) has highly surface polarity and sorption capacity. The elemental analysis, scanning electron microscopy, thermal analysis, ultraviolet/visible/infrared spectroscopies and X-ray diffraction were used for characterization of AM-PUF. The surface of AM-PUF has amorphous character (broadband at 2θ, 21.75°) and contains several active sites e.g. NH, OH, CO, CC and COC groups. The electrical conductivity (σ), iodine value and methylene blue index of AM-PUF are 1.7×10 -5 Ω -1 m -1 , 208mg/g and 107mg/g. The AM-PUF has a high efficiency for completely removing (99-100%) of Aldrin, DDT, Endrin, Heptachlor, Heptachlor epoxide and Lindane pesticides in both acidic and alkaline solutions. The removing rates of the organochlorine pesticides from wastewater are very rapid (t 1/2 =22s). The negative value of ΔG (-10.9kJ/mol) for removing of OCPs using AM-PUF showed that the feasibility of the removing process and its spontaneous nature. Copyright © 2017 Elsevier B.V. All rights reserved.

  20. Peptide-modified liposomes for selective targeting of bombesin receptors overexpressed by cancer cells: a potential theranostic agent

    Science.gov (United States)

    Accardo, Antonella; Salsano, Giuseppina; Morisco, Anna; Aurilio, Michela; Parisi, Antonio; Maione, Francesco; Cicala, Carla; Tesauro, Diego; Aloj, Luigi; De Rosa, Giuseppe; Morelli, Giancarlo

    2012-01-01

    Objectives Drug delivery systems consisting of liposomes displaying a cell surface receptor-targeting peptide are being developed to specifically deliver chemotherapeutic drugs to tumors overexpressing a target receptor. This study addresses novel liposome composition approaches to specifically target tissues overexpressing bombesin (BN) receptors. Methods A new amphiphilic peptide derivative (MonY-BN) containing the BN(7–14) peptide, the DTPA (diethylenetriaminepentaacetate) chelating agent, a hydrophobic moiety with two C18 alkyl chains, and polyethylene glycol spacers, has been synthesized by solid-phase methods. Liposomes have been generated by co-aggregation of MonY-BN with 1,2-distearoyl-sn-glycero-3-phosphocholine (DSPC). The structural and biological properties of these new target-selective drug-delivery systems have been characterized. Results Liposomes with a DSPC/MonY-BN (97/3 molar ratio) composition showed a diameter of 145.5 ± 31.5 nm and a polydispersity index of 0.20 ± 0.05. High doxorubicin (Dox) loading was obtained with the remote pH gradient method using citrate as the inner buffer. Specific binding to PC-3 cells of DSPC/MonY-BN liposomes was obtained (2.7% ± 0.3%, at 37°C), compared with peptide-free DSPC liposomes (1.4% ± 0.2% at 37°C). Incubation of cells with DSPC/ MonY-BN/Dox showed significantly lower cell survival compared with DSPC/Dox-treated cells, in the presence of 100 ng/mL and 300 ng/mL drug amounts, in cytotoxicity experiments. Intravenous treatment of PC-3 xenograft-bearing mice with DSPC/MonY-BN/Dox at 10 mg/kg Dox dose produced higher tumour growth inhibition (60%) compared with nonspecific DSPC/ Dox liposomes (36%) relative to control animals. Conclusion The structural and loading properties of DSPC/MonY-BN liposomes along with the observed in-vitro and in-vivo activity are encouraging for further development of this approach for target-specific cancer chemotherapy. PMID:22619538

  1. Occurrence and profiles of organic sun-blocking agents in surface waters and sediments in Japanese rivers and lakes

    Energy Technology Data Exchange (ETDEWEB)

    Kameda, Yutaka, E-mail: kameda.yutaka@pref.saitama.lg.jp [Center for Environmental Science in Saitama, Kamitanadare 914, Kazo 347-0115 (Japan); Kimura, Kumiko; Miyazaki, Motonobu [Saitama City Institute of Health Science and Research, Suzuya 7-5-12, Chuo-ku, Saitama 338-0013 (Japan)

    2011-06-15

    Sun-blocking agents including eight UV filters (UVF) and 10 UV light stabilizers (UVLS) were measured in water and sediment collected from 22 rivers, four sewage treatment plant effluents (STPE) and three lakes in Japan. Total sun blocking agents levels ranged from N.D. to 4928 ng/L and from 2.0 to 3422 {mu}g/kg dry wt in surface water and in sediment, respectively. Benzyl salicylate, benzophenone-3, 2-ethyl hexyl-4-methoxycinnamte (EHMC) and octyl salicylate were dominant in surface water receiving wastewater effluents and STPE, although UV-328, benzophenone and EHMC were dominant in other surface water except background sites. Three UVF and nine UVLS were observed from all sediment and their compositions showed similar patterns with UV-328 and UV-234 as the most prevalent compounds. Homosalate, octocrylene, UV-326, UV-327, UV-328 and UV-234 were significantly correlated with Galaxolide in sediments. Concentrations of UV-327 and UV-328 also had strong correlation between those of UV-326 in sediment. - Highlights: > Total sun-blocking agents levels ranged from N.D. to 4928 ng/L in surface water from 29 sampling sites. > The maximum concentration of total sun-blocking agents was 3422 {mu}g/kg dry wt. in sediment. > Residential wastewaters and STPE were considered to be potential sources of UVLS in river and lakes. > Most of sun-blocking agents in sediment were significantly correlated with HHCB. > UV-326 had a strong linear correlation between UV-327 as well as UV-328 in all sediment. - Occurrence of eight UV filters and 10 UV light stabilizers in surface water and sediment were investigated and characterized their compositions in water and sediment.

  2. Speciation of uranium in surface-modified, hydrothermally treated, (UO2)2+-exchanged smectite clays

    International Nuclear Information System (INIS)

    Giaquinta, D.M.; Soderholm, L.; Yuchs, S.E.; Wasserman, S.R.

    1997-01-01

    A successful solution to the problem of disposal and permanent storage of water soluble radioactive species must address two issues: exclusion of the radionuclides from the environment and the prevention of leaching from the storage media into the environment. Immobilization of radionuclides in clay minerals has been studied. In addition to the use of clays as potential waste forms, information about the interactions of radionuclides with clays and how such interactions affect their speciations is crucial for successful modeling of actinide-migration. X-ray absorption spectroscopy (XAS) is used to determine the uranium speciation in exchanged and surface-modified clays. The XAS data from uranyl-loaded bentonite clay are compared with those obtained after the particle surfaces have been coated with alkylsilanes. These silane films, which render the surface of the clay hydrophobic, are added in order to minimize the ability of external water to exchange with the water in the clay interlayer, thereby decreasing the release rate of the exchanged-uranium species. Mild hydrothermal conditions are used in an effort to mimic potential geologic conditions that may occur during long-term radioactive waste storage. The XAS spectra indicate that the uranyl monomer species remain unchanged in most samples, except in those samples that were both coated with an alkylsilane and hydrothermally treated. When the clay was coated with an organic film, formed by the acidic deposition of octadecyltrimethoxysilane, hydrothermal treatment results in the formation of aggregated uranium species in which the uranium is reduced from U VI to U IV

  3. Adsorption of ibuprofen from aqueous solution on chemically surface-modified activated carbon cloths

    Directory of Open Access Journals (Sweden)

    Hanen Guedidi

    2017-05-01

    Full Text Available This study aims to investigate the performance of an activated carbon cloth for adsorption of ibuprofen. The cloth was oxidized by a NaOCl solution (0.13 mol L−1 or thermally treated under N2 (700 °C for 1 hour. The raw and modified cloths were characterized by N2 adsorption–desorption measurement at 77 K, CO2 adsorption at 273 K, Boehm titrations, pHPZC measurements, X-ray Photoelectron Spectroscopy analysis, and by infrared spectroscopy. The NaOCl treatment increases the acidic sites, mostly creating phenolic and carboxylic groups and decreases both the specific surface area and slightly the micropore volume. However, the thermal treatment at 700 °C under N2 induced a slight increase in the BET specific surface area and yielded to the only increase in the carbonyl group content. Ibuprofen adsorption studies of kinetics and isotherms were carried out at pH = 3 and 7. The adsorption properties were correlated to the cloth porous textures, surface chemistry and pH conditions. The isotherms of adsorption were better reproduced by Langmuir–Freundlich models at 298, 313 and 328 K. The adsorption of ibuprofen on the studied activated carbon cloths at pH 3 was an endothermic process. The pore size distributions of all studied ibuprofen-loaded fabrics were determined by DFT method to investigate the accessible porosity of the adsorbate. Both treatments do not influence the kind of micropores where the adsorption of ibuprofen occurred.

  4. In vitro and in vivo anticancer activity of surface modified paclitaxel attached hydroxyapatite and titanium dioxide nanoparticles.

    Science.gov (United States)

    Venkatasubbu, G Devanand; Ramasamy, S; Reddy, G Pramod; Kumar, J

    2013-08-01

    Targeted drug delivery using nanocrystalline materials delivers the drug at the diseased site. This increases the efficacy of the drug in killing the cancer cells. Surface modifications were done to target the drug to a particular receptor on the cell surface. This paper reports synthesis of hydroxyapatite and titanium dioxide nanoparticles and modification of their surface with polyethylene glycol (PEG) followed by folic acid (FA). Paclitaxel, an anticancer drug, is attached to functionalized hydroxyapatite and titanium dioxide nanoparticles. The pure and functionalised nanoparticles are characterised with XRD, TEM and UV spectroscopy. Anticancer analysis was carried out in DEN induced hepatocarcinoma animals. Biochemical, hematological and histopathological analysis show that the surface modified paclitaxel attached nanoparticles have an higher anticancer activity than the pure paclitaxel and surface modified nanoparticles without paclitaxel. This is due to the targeting of the drug to the folate receptor in the cancer cells.

  5. Synthesis and Characterization of Surface Modified, Fluorescent and Biocompatible ZnS Nanoparticles with a Hydrophobic Chitosan Derivative.

    Science.gov (United States)

    Jothimani, B; Sureshkumar, S; Venkatachalapathy, B

    2017-07-01

    The introduction of a hydrophobic moiety on chitosan enhances the self-assembling properties, mucoadhesion, the permeability of the macromolecule and aids in target specific delivery. Our group synthesized a hydrophobic trans N-(6,6-Dimethyl-2-hepten-4-ynyl)chitosan derivative (CSD) and studied the surface modification of ZnS nanoparticles in a single pot reaction. X-ray diffraction studies and FESEM imaging confirms the nano size and morphology of the surface modified Zinc sulfide nanoparticles (ZnS-CSD NPs). The proposed ZnS-CSD NPs showed excellent emission at 457 nm. Photostability studies indicate that the surface modified ZnS-CSD NPs possess better photostability than Rhodamine B and FITC. Cell viability tests confirmed the biocompatibility of the modified nanoparticles. All these features of ZnS- CSD NPs makes these candidates an excellent choice in a wide range of in vitro or in vivo studies as fluorescent biological labels.

  6. Laser-Modified Surface Enhances Osseointegration and Biomechanical Anchorage of Commercially Pure Titanium Implants for Bone-Anchored Hearing Systems

    Science.gov (United States)

    Omar, Omar; Simonsson, Hanna; Palmquist, Anders; Thomsen, Peter

    2016-01-01

    Osseointegrated implants inserted in the temporal bone are a vital component of bone-anchored hearing systems (BAHS). Despite low implant failure levels, early loading protocols and simplified procedures necessitate the application of implants which promote bone formation, bone bonding and biomechanical stability. Here, screw-shaped, commercially pure titanium implants were selectively laser ablated within the thread valley using an Nd:YAG laser to produce a microtopography with a superimposed nanotexture and a thickened surface oxide layer. State-of-the-art machined implants served as controls. After eight weeks’ implantation in rabbit tibiae, resonance frequency analysis (RFA) values increased from insertion to retrieval for both implant types, while removal torque (RTQ) measurements showed 153% higher biomechanical anchorage of the laser-modified implants. Comparably high bone area (BA) and bone-implant contact (BIC) were recorded for both implant types but with distinctly different failure patterns following biomechanical testing. Fracture lines appeared within the bone ~30–50 μm from the laser-modified surface, while separation occurred at the bone-implant interface for the machined surface. Strong correlations were found between RTQ and BIC and between RFA at retrieval and BA. In the endosteal threads, where all the bone had formed de novo, the extracellular matrix composition, the mineralised bone area and osteocyte densities were comparable for the two types of implant. Using resin cast etching, osteocyte canaliculi were observed directly approaching the laser-modified implant surface. Transmission electron microscopy showed canaliculi in close proximity to the laser-modified surface, in addition to a highly ordered arrangement of collagen fibrils aligned parallel to the implant surface contour. It is concluded that the physico-chemical surface properties of laser-modified surfaces (thicker oxide, micro- and nanoscale texture) promote bone bonding

  7. The comparison of provisional luting agents and abutment surface roughness on the retention of provisional implant-supported crowns.

    Science.gov (United States)

    Kim, Yongsik; Yamashita, Junro; Shotwell, Jeffrey L; Chong, Kok-Heng; Wang, Hom-Lay

    2006-06-01

    In immediate implant loading, it is important to keep provisional restorations in place during early-phase healing. Current luting agents for provisional restorations may provide inadequate retention, creating a clinical challenge. This study compared the retention of provisional autopolymerizing acrylic resin implant-supported single restorations with combinations of different implant abutment surface conditions and provisional luting agents. Thirty solid titanium implant abutments (ITI), 4 mm high, were divided into 3 groups. Ten abutments were unaltered, 10 were airborne-particle abraded with 50-microm aluminum oxide, and 10 were roughened with a medium-roughness diamond rotary cutting instrument. Thirty implant analogs (ITI) were mounted in autopolymerizing acrylic resin blocks. A solid titanium implant abutment was placed in each implant analog and torqued to 35 N.cm. After fabrication of 4 provisional acrylic resin crowns for each abutment, provisional luting agents TempBond, TempBond NE, Life, and Zone were used to secure the provisional crowns to the respective abutments. All specimens were luted with one of the provisional luting agents for a given test. After ultrasonic cleaning of the abutments, another provisional crown was luted with another luting agent. All specimens were stored in 100% humidity environment for 1 day at 37 degrees C prior to testing. Each provisional acrylic resin crown was pulled from the abutment with a 500-kg load cell in a universal testing machine at a crosshead speed of 0.5 cm/minute, and tensile strength was recorded (N). Data were analyzed using analysis of variance (ANOVA) and the Scheffe test (alpha=.05). Tensile strength was significantly higher for Life and TempBond NE than for TempBond and Zone, regardless of the surface conditions (P=.0001). The result of the 2-way ANOVA indicated that a significant interaction existed between the provisional luting agents and surface conditions (P=.0039). TempBond NE showed

  8. Development of genetically modified eliminable human dermal fibroblast feeder cells for ocular surface regeneration medicine.

    Science.gov (United States)

    Li, Yingli; Inoue, Tomoyuki; Takamatsu, Fumihiko; Maeda, Naoyuki; Ohashi, Yuichi; Nishida, Kohji

    2013-11-15

    Cultured human corneal limbal stem/progenitor cells are usually established and maintained on feeder layers. However, animal feeder cells are associated with viral infection, pathogen transmission, and xenogenic contamination. All feeder cells also can be mixed easily into cell-sheet production, causing self-contamination. We developed a line of labeled, immortalized, eliminable human dermal fibroblast cells to eliminate these problems. The enhanced green fluorescent protein gene, human-derived telomerase reverse transcriptase gene, and herpes simplex virus thymidine kinase gene were transfected into human dermal fibroblast cells to establish labeled, immortalized, eliminable feeder cells. Established eliminable dermal fibroblasts (TERT+TK-D) were treated with mitomycin, cocultured with human limbal stem/progenitor cells to regenerate epithelium sheets, and compared with 3T3 feeder cells. Established TERT+TK-D feeder cells maintained immortalization, visualization, and eliminable characteristics during 6 months of continuous passages. The colony-forming efficiency of limbal stem/progenitor cells was similar in the TERT+TK-D group (11.77 ± 0.21%) and the 3T3 group (12.8 ± 1.61%) (P = 0.332). All cell sheets were well stratified into 4 to 5 layers. The TERT+TK-D group colonies and epithelial cell sheets showed weaker staining of corneal epithelium differentiation marker K3 than the 3T3 group and quantitative analysis of mRNA transcripts. Moreover, PCR analysis against the long terminal repeat sequence of the lentiviral vector integrated into the genetically modified feeder cells showed no contamination of ganciclovir-treated regeneration epithelial sheets. Genetically modified, labeled, immortalized, eliminable human dermal feeder cells are promising substitutes for 3T3 feeder cells for xenogeny-free ocular surface regeneration.

  9. Nanocomposite fibers and film containing polyolefin and surface-modified carbon nanotubes

    Science.gov (United States)

    Chu,Benjamin; Hsiao, Benjamin S.

    2010-01-26

    Methods for modifying carbon nanotubes with organic compounds are disclosed. The modified carbon nanotubes have enhanced compatibility with polyolefins. Nanocomposites of the organo-modified carbon nanotubes and polyolefins can be used to produce both fibers and films having enhanced mechanical and electrical properties, especially the elongation-to-break ratio and the toughness of the fibers and/or films.

  10. Nanoparticle coating on the silane-modified surface of magnesium for local drug delivery and controlled corrosion.

    Science.gov (United States)

    Lee, Won Seok; Park, Min; Kim, Myung Hun; Park, Chun Gwon; Huh, Beom Kang; Seok, Hyun Kwang; Choy, Young Bin

    2016-01-01

    In this study, we proposed a potential method for the preparation of a magnesium-based medical device for local drug delivery and controlled corrosion. A magnesium surface was modified with 3-aminopropyltrimethoxy silane, and the resulting surface was then coated with drug-loaded nanoparticles made of poly (lactic-co-glycolic acid) via electrophoretic deposition. The drug-loaded nanoparticles (i.e., Tr_NP) exhibited a size of 250 ± 67 nm and a negative zeta potential of -20.9 ± 2.75 mV. The drug was released from the nanoparticles in a sustained manner for 21 days, and this did not change after their coating on the silane-modified magnesium. The silane-modified surface suppressed magnesium corrosion. When immersed in phosphate buffered saline at pH 7.4, the average rate of hydrogen gas generation was 0.41-0.45 ml/cm(2)/day, compared to 0.58-0.6 ml/cm(2)/day from a bare magnesium surface. This corrosion profile was not significantly changed after nanoparticle coating under the conditions employed in this work. The in vitro cell test revealed that the drug released from the coating was effective during the whole release period of 21 days, and both the silane-modified surface and carrier nanoparticles herein were not cytotoxic. © The Author(s) 2015.

  11. A Choline Oxidase Amperometric Bioassay for the Detection of Mustard Agents Based on Screen-Printed Electrodes Modified with Prussian Blue Nanoparticles

    Directory of Open Access Journals (Sweden)

    Fabiana Arduini

    2015-02-01

    Full Text Available In this work a novel bioassay for mustard agent detection was proposed. The bioassay is based on the capability of these compounds to inhibit the enzyme choline oxidase. The enzymatic activity, which is correlated to the mustard agents, was electrochemically monitored measuring the enzymatic product, hydrogen peroxide, by means of a screen-printed electrode modified with Prussian Blue nanoparticles. Prussian Blue nanoparticles are able to electrocatalyse the hydrogen peroxide concentration reduction at low applied potential (−50 mV vs. Ag/AgCl, thus allowing the detection of the mustard agents with no electrochemical interferences. The suitability of this novel bioassay was tested with the nitrogen mustard simulant bis(2-chloroethylamine and the sulfur mustard simulants 2-chloroethyl ethyl sulfide and 2-chloroethyl phenyl sulfide. The bioassay proposed in this work allowed the detection of mustard agent simulants with good sensitivity and fast response, which are excellent premises for the development of a miniaturised sensor well suited for an alarm system in case of terrorist attacks.

  12. Relationship between the structure of polymer network using glutaraldehyde crosslinking agent and physico-mechanical properties of biopolymer membrane based on polyvinyl alcohol (PVA) modified with cassava starch

    International Nuclear Information System (INIS)

    Nguyen Huong Hao; Pham The Trinh; Mai Van Tien; Nguyen Huy Tung; Nguyen Thi Thanh Nhan

    2015-01-01

    The relationship between network structure and the properties of starch modified PVA membrane, such as the relationship between the crosslinking density (n), the average molecular weight of crosslink (M c ), the mesh size (ξ) to the crystallinity were investigated. The increasing of glutaraldehyde crosslinking agent decreases the molecular weight between crosslink (M c ) rapidly from 8985 g/mol to 1950 g/mol and the mesh size from 613 Å to 227 Å. Salicylic diffusion coefficient of the membrane was determined to be 4.15 x 10 cm 2 /s. This was proven that PVA/TBS membrane was able to have permeable molecules that contained bulky functional groups. (author)

  13. Performance of Poly(lactic acid) Surface Modified Films for Food Packaging Application

    Science.gov (United States)

    Dalla Rosa, Marco; Iordanskii, Alexey L.

    2017-01-01

    Five Poly(lactic acid) (PLA) film samples were analyzed to study the gas barrier behavior, thermal stability and mechanical performance for food packaging application. O2, CO2, N2, N2O, and C2H4 pure gases; Air; and Modified Atmosphere (MA, 79% N2O/21% O2) were used to analyze the influence of the chemical structure, storage temperature and crystalline phase on the gas barrier behavior. The kinetic of the permeation process was investigated at different temperatures, ranging from 5 °C to 40 °C. Annealing thermal treatment on the samples led to the crystalline percentage, influencing especially the gas solubility process. Thermal properties such as Tg and χc, and mechanical properties such as tensile strength and modulus were remarkably improved with surface PLA modification. A more pronounced reinforcing effect was noted in the case of metallization, as well as improved gas barrier performance. Tensile testing and tensile cycling tests confirmed the rigidity of the films, with about a 20% loss of elasticity after 25 cycles loading. PMID:28773210

  14. Modified colloidal primitive model as a homogeneous surface charge distribution: ζ-potential.

    Science.gov (United States)

    Manzanilla-Granados, Héctor M; Lozada-Cassou, Marcelo

    2013-10-03

    An integral equations theory is derived and applied to a modified colloidal primitive model (MCPM), for finite concentration colloidal dispersions. In MCPM, the charge on the colloidal particle is assumed to be smeared on its surface. We find important quantitative and qualitative differences of the ζ-potential, induced charge, and the colloid-colloid electric effective force, calculated in the MCPM, with those obtained from the colloidal primitive model (CPM), where the colloidal charge is assumed to be in the center of the particle, in spite of the fact that, due to Gauss's law, both models have the same particle distribution function. In particular, for the same parameters, while the ζ-potential is positive in MCPM, is negative in the CPM, implying opposite electrophoretic mobilities, μ. An inverse μ has been theoretically predicted in the past, for infinite dilution colloidal dispersions. The MCPM could be a better model for some colloidal particles. In both models, the CPM and the MCPM, it is found a very long-range colloid-colloid correlation, in accordance with previous Monte Carlo simulations. The electrostatic, as well as entropic, like-charged colloid-colloid forces are oscillatory, implying a long-range attraction.

  15. Formation of biodegradable microcapsules utilizing 3D, selectively surface-modified PDMS microfluidic devices.

    Science.gov (United States)

    Liao, Chung-Yu; Su, Yu-Chuan

    2010-02-01

    We have successfully demonstrated the formation of biodegradable microcapsules utilizing PDMS double-emulsification devices. Specially designed 3D PDMS microchannels with surfaces selectively modified by a self-aligned photografting process are employed to generate monodisperse water-in-organic-solvent-in-water (W/O/W) emulsions in a controlled manner. Mainly by varying the outer and inner fluid flow-rates, the dimensions of resulting double emulsions can be adjusted as desired. Meanwhile, biodegradable materials are dissolved in the middle organic solvent (in this work ethyl acetate is used), and solidified into microcapsules once the solvent is extracted. In the prototype demonstration, microcapsules made up of poly(L-lactic acid), trilaurin, and phosphocholine were successfully fabricated. In addition, it was also demonstrated that gamma-Fe(2)O(3) nanoparticles can be simultaneously embedded into the microcapsules, which consequently become responsive to electromagnetic stimulation. As such, the presented PDMS microfluidic devices could potentially serve as versatile encapsulation apparatus, and the fabricated biodegradable microcapsules could function as controlled delivery systems, which are desired for a variety of biological and pharmaceutical applications.

  16. Zinc-modified titanium surface enhances osteoblast differentiation of dental pulp stem cells in vitro.

    Science.gov (United States)

    Yusa, Kazuyuki; Yamamoto, Osamu; Takano, Hiroshi; Fukuda, Masayuki; Iino, Mitsuyoshi

    2016-07-08

    Zinc is an essential trace element that plays an important role in differentiation of osteoblasts and bone modeling. This in vitro study aimed to evaluate the osteoblast differentiation of human dental pulp stem cells (DPSCs) on zinc-modified titanium (Zn-Ti) that releases zinc ions from its surface. Based on real-time PCR, alkaline phosphatase (ALP) activity and Western blot analysis data, we investigated osteoblast differentiation of DPSCs cultured on Zn-Ti and controls. DPSCs cultured on Zn-Ti exhibited significantly up-regulated gene expression levels of osteoblast-related genes of type I collagen (Col I), bone morphogenetic protein 2 (BMP2), ALP, runt-related transcription factor 2 (Runx2), osteopontin (OPN), and vascular endothelial growth factor A (VEGF A), as compared with controls. We also investigated extracellular matrix (ECM) mineralization by Alizarin Red S (ARS) staining and found that Zn-Ti significantly promoted ECM mineralization when compared with controls. These findings suggest that the combination of Zn-Ti and DPSCs provides a novel approach for bone regeneration therapy.

  17. Artificial Intelligence Mechanisms on Interactive Modified Simplex Method with Desirability Function for Optimising Surface Lapping Process

    Directory of Open Access Journals (Sweden)

    Pongchanun Luangpaiboon

    2014-01-01

    Full Text Available A study has been made to optimise the influential parameters of surface lapping process. Lapping time, lapping speed, downward pressure, and charging pressure were chosen from the preliminary studies as parameters to determine process performances in terms of material removal, lap width, and clamp force. The desirability functions of the-nominal-the-best were used to compromise multiple responses into the overall desirability function level or D response. The conventional modified simplex or Nelder-Mead simplex method and the interactive desirability function are performed to optimise online the parameter levels in order to maximise the D response. In order to determine the lapping process parameters effectively, this research then applies two powerful artificial intelligence optimisation mechanisms from harmony search and firefly algorithms. The recommended condition of (lapping time, lapping speed, downward pressure, and charging pressure at (33, 35, 6.0, and 5.0 has been verified by performing confirmation experiments. It showed that the D response level increased to 0.96. When compared with the current operating condition, there is a decrease of the material removal and lap width with the improved process performance indices of 2.01 and 1.14, respectively. Similarly, there is an increase of the clamp force with the improved process performance index of 1.58.

  18. Structural, electronic and mechanical properties of inner surface modified imogolite nanotubes

    Directory of Open Access Journals (Sweden)

    Maurício Chagas Da Silva

    2015-03-01

    Full Text Available The electronic, structural and mechanical properties of the modified imogolites have been investigated using self consistent charge-density functional-tight binding method with a posteriori treatment of the dispersion interaction (SCC-DFTB-D. The zigzag (12,0 imogolite has been used as the initial structure for the calculations. The functionalization of the interior (12,0 imogolite nanotubes by organosilanes and by heat treatment leading to the dehydroxylation of the silanols were investigated. The reaction of the silanols with the trimethylmethoxysilanes is favored and the arrangement of the different substitutions that leads to the most symmetrical structures are preferred. The Young moduli and band gaps are slightly decreased. However, the dehydroxylation of the silanol groups in the inner surface of the imogolite leads to the increase of the Young moduli and a drastic decrease of the band gap of about 4.4 eV. It has been shown that the degree of the dehydroxylation can be controlled by heat treatment and tune the band gap, eventually, leading to a semiconductor material with well defined nanotube structure.

  19. Colloid properties of hydrophobic modified alginate: Surface tension, ζ-potential, viscosity and emulsification.

    Science.gov (United States)

    Wu, Zongmei; Wu, Jie; Zhang, Ruling; Yuan, Shichao; Lu, Qingliang; Yu, Yueqin

    2018-02-01

    Micelle properties of hydrophobic modified alginate (HM-alginate) in various dispersion media have been studied by surface tension, ζ-potential, and viscosity measurements. Effect of salt on micelle properties showed that the presence of counter ion weakened the repulsive interaction between surfactant ions, decreased the critical micelle concentration (CMC) value of the HM-alginate, reduced the effective volume dimensions of HM-alginate and hence viscosity, which coincide with the corresponding ζ-potential values. Soy oil-in-water emulsions, stabilized solely by HM-alginate, were produced in high speed homogenization conditions and their stability properties were studied by visual inspection, optical microscopy and droplet size measurements. The results showed that emulsions (oil-water ratio was 1:7) containing 15mg/mL HM-alginate presented better stability during 15days storage, which stating clearly that HM-alginate is an effective emulsifier to stabilize oil-in-water emulsions. The herein presented homogeneous method for preparation of emulsion has the potential to be used in food industry. Copyright © 2017 Elsevier Ltd. All rights reserved.

  20. TiO₂ Films Modified with Au Nanoclusters as Self-Cleaning Surfaces under Visible Light.

    Science.gov (United States)

    Liao, Ting-Wei; Verbruggen, Sammy W; Claes, Nathalie; Yadav, Anupam; Grandjean, Didier; Bals, Sara; Lievens, Peter

    2018-01-08

    In this study, we applied cluster beam deposition (CBD) as a new approach for fabricating efficient plasmon-based photocatalytic materials. Au nanoclusters (AuNCs) produced in the gas phase were deposited on TiO₂ P25-coated silicon wafers with coverage ranging from 2 to 8 atomic monolayer (ML) equivalents. Scanning Electron Microscopy (SEM) images of the AuNCs modified TiO₂ P25 films show that the surface is uniformly covered by the AuNCs that remain isolated at low coverage (2 ML, 4 ML) and aggregate at higher coverage (8 ML). A clear relationship between AuNCs coverage and photocatalytic activity towards stearic acid photo-oxidation was measured, both under ultraviolet and green light illumination. TiO₂ P25 covered with 4 ML AuNCs showed the best stearic acid photo-oxidation performance under green light illumination (Formal Quantum Efficiency 1.6 × 10 -6 over a period of 93 h). These results demonstrate the large potential of gas-phase AuNCs beam deposition technology for the fabrication of visible light active plasmonic photocatalysts.

  1. Polypropylene nonwoven surface modified through introducing porous microspheres: Preparation, characterization and adsorption

    Science.gov (United States)

    Du, Xiao; Wei, Junfu; Liu, Wei; Zhou, Xiangyu; Dai, Danyang

    2016-01-01

    A new porous fabric adsorbent (PM/PP nonwoven) was prepared by hydrogen bonding self-assembly method, in which poly(divinylbenzene-co-4-vinylpyridine) microspheres were introduced onto the surface of PP-g-AA (polypropylene grafted acrylic acid) nonwoven. The effects of the main conditions for self-assembly reaction such as mass ratio of microsphere to nonwoven, pH and the grafting degree of acrylic acid were studied. In addition, the adsorption mechanisms and interactions for three VOCs (styrene, cyclohexane, acetone) were systematically elucidated. The resulting 28.2% PM/PP nonwoven obtained a higher adsorption amount (52.8 mg/g) of styrene vapor, which was 88 times greater than that of original PP nonwoven. Meanwhile, the kinetic studies suggested that the Yoon and Nelson model is suitable to describe the adsorption mechanism of styrene over the modified nonwovens. Adsorption and pressure drop data showed that PM/PP nonwoven had good adsorption ability and air permeability due to its abundant functional groups and porous structures. Taken together, it is expected that PM/PP nonwoven would be a promising adsorbent for removal of VOCs from the gas streams.

  2. Constructing Fluorine-Free and Cost-Effective Superhydrophobic Surface with Normal-Alcohol-Modified Hydrophobic SiO2 Nanoparticles.

    Science.gov (United States)

    Ye, Hui; Zhu, Liqun; Li, Weiping; Liu, Huicong; Chen, Haining

    2017-01-11

    Superhydrophobic coatings have drawn much attention in recent years for their wide potential applications. However, a simple, cost-effective, and environmentally friendly approach is still lacked. Herein, a promising approach using nonhazardous chemicals was proposed, in which multiple hydrophobic functionalized silica nanoparticles (SiO 2 NPs) were first prepared as core component, through the efficient reaction between amino group containing SiO 2 NPs and the isocyanate containing hydrophobic surface modifiers synthesized by normal alcohols, followed by simply spraying onto various substrates for superhydrophobic functionalization. Furthermore, to further improve the mechanical durability, an organic-inorganic composite superhydrophobic coating was fabricated by incorporating cross-linking agent (polyisocyanate) into the mixture of hydrophobic-functionalized SiO 2 NPs and hydroxyl acrylic resin. The hybrid coating with cross-linked network structures is very stable with excellent mechanical durability, self-cleaning property and corrosion resistance.

  3. The influence of surface modified poly(L-lactic acid) films on the differentiation of human monocytes into macrophages

    OpenAIRE

    Correia, Clara R.; Gaifem, Joana; Oliveira, Mariana Braga; Silvestre, Ricardo Jorge Leal; Mano, J. F.

    2017-01-01

    Macrophages play a crucial role in the biological performance of biomaterials, as key factors in defining the optimal inflammation-healing balance towards tissue regeneration and implant integration. Here, we investigate how different surface modifications performed on poly(L-lactic acid) (PLLA) films would influence the differentiation of human monocytes into macrophages. We tested PLLA films without modification, surface-modified by plasma treatment (pPLLA) or by combining plasma treatment ...

  4. Evaluation of antimicrobial and physical properties of orthodontic composite resin modified by addition of antimicrobial agents--an in-vitro study.

    Science.gov (United States)

    Sehgal, Vikas; Shetty, V Surendra; Mogra, Subraya; Bhat, Gopalkrishna; Eipe, Montu; Jacob, Shery; Prabu, Laxman

    2007-04-01

    This study was designed to investigate the antimicrobial and physical properties of orthodontic composite resin modified by the addition of antimicrobial agents. Unite bonding adhesive (3M Unitek, Monrovia, Calif), a chemically cured composite resin, modified by the addition of benzalkonium chloride (BAC), chlorhexidine, and triclosan in concentrations of 0.1 wt%, 0.2 wt%, and 0.3 wt%, respectively, was formed into tablets for testing. The tablets of each group and a control group were subjected to the agar plate diffusion test to measure the zone of bacterial inhibition. In addition, they were incubated for 24 hours in tryptic soy broth inoculated with Streptococcus mutans and examined for bacterial growth. A total of 80 extracted premolars were collected and divided into 2 sets of 40 teeth each. Stainless steel Begg brackets were bonded by using control and experimental composites. A universal testing machine was used to determine shear bond strength. The first set of teeth was tested after 24 hours and the second set after 25 days of storage in distilled water. Time-dependent release of antimicrobial agents from the modified composites was monitored spectrophotometrically. The findings indicated that (1) addition of BAC to the orthodontic composite resin enhanced its antimicrobial properties, (2) there was no significant difference in the bond strengths of the control and the experimental resin tested after 24 hours and 25 days, and (3) maximum release of BAC from the modified resin was higher than that of chlorhexidine or triclosan, and was much higher than the minimum inhibitory concentration level.

  5. Strengthening and toughening of poly(L-lactide) composites by surface modified MgO whiskers

    Energy Technology Data Exchange (ETDEWEB)

    Wen, Wei [Biomaterial Research Laboratory, Department of Material Science and Engineering, College of Science and Engineering, Jinan University, Guangzhou 510632 (China); Luo, Binghong, E-mail: tluobh@jnu.edu.cn [Biomaterial Research Laboratory, Department of Material Science and Engineering, College of Science and Engineering, Jinan University, Guangzhou 510632 (China); Engineering Research Center of Artificial Organs and Materials, Ministry of Education, Guangzhou 510632 (China); Qin, Xiaopeng; Li, Cairong [Biomaterial Research Laboratory, Department of Material Science and Engineering, College of Science and Engineering, Jinan University, Guangzhou 510632 (China); Liu, Mingxian; Ding, Shan [Biomaterial Research Laboratory, Department of Material Science and Engineering, College of Science and Engineering, Jinan University, Guangzhou 510632 (China); Engineering Research Center of Artificial Organs and Materials, Ministry of Education, Guangzhou 510632 (China); Zhou, Changren, E-mail: tcrz9@jnu.edu.cn [Biomaterial Research Laboratory, Department of Material Science and Engineering, College of Science and Engineering, Jinan University, Guangzhou 510632 (China); Engineering Research Center of Artificial Organs and Materials, Ministry of Education, Guangzhou 510632 (China)

    2015-03-30

    Highlights: • The grafted PLLA chain on the surface of g-MgO whisker was ruled out by FTIR spectroscopy and TG/DTG analyses. • The excellent dispersion of g-MgO whiskers and the strong interfacial adhesion of g-MgO whiskers/PLLA composite were proved by FSEM. • Comparing to MgO particles and MgO whiskers, fibrous-like g-MgO whiskers are the most effective reinforcing and toughening fillers for PLLA. - Abstract: To improve both the strength and toughness of poly(L-lactide) (PLLA), fibrous-like MgO whiskers with diameters of 0.15–1 μm and lengths of 15–110 μm were prepared, and subsequently surface modified with L-lactide to obtain grafted MgO whiskers (g-MgO whiskers). The structures and properties of MgO whiskers and g-MgO whiskers were studied. Then, a series of MgO whiskers/PLLA and g-MgO whiskers/PLLA composites were prepared by solution casting method, for comparison, MgO particles/PLLA composite was prepared too. The resulting composites were evaluated in terms of hydrophilicity, crystallinity, dispersion of whiskers, interfacial adhesion and mechanical performance by means of polarized optical microscopy (POM), contact angle measurement, field emission scanning electron microscope (FSEM), transmission electron microscopy (TEM) and tensile testing. The results revealed that the crystallization rate and hydrophilicity of PLLA were improved by the introduction of MgO whiskers and g-MgO whiskers. The g-MgO whiskers can disperse more uniformly in and show stronger interfacial adhesion with the matrix than MgO whiskers as a result of the surface modification. Due to the bridge effect of the whiskers and the excellent interfacial adhesion between g-MgO whiskers and PLLA, g-MgO whiskers/PLLA composites exhibited remarkably higher strength, modulus and toughness compared to the pristine PLLA, MgO particles/PLLA and MgO whiskers/PLLA composites.

  6. Surface-modified nanoparticles as a new, versatile, and mechanically robust nonadhesive coating : Suppression of protein adsorption and bacterial adhesion

    NARCIS (Netherlands)

    Holmes, P. F.; Currie, E. P. K.; Thies, J. C.; van der Mei, H. C.; Busscher, H. J.; Norde, W.

    2009-01-01

    The synthesis of surface-modified silica nanoparticles, chemically grafted with acrylate and poly(ethylene glycol) (PEG) groups, and the ability of the resulting crosslinked coatings to inhibit protein adsorption and bacterial adhesion are explored. Water contact angles, nanoindentation, and atomic

  7. Surface Structure and Photocatalytic Properties of Bi2WO6 Nanolatelets Modified by Molybdena Islands from Chemical Vapor Deposition

    NARCIS (Netherlands)

    Dittmer, A.; Menze, J.; Mei, Bastian Timo; Strunk, J.; Luftman, H.S.; Gutkowski, R.; Wachs, I.E.; Schuhmann, W.; Muhler, M.

    2016-01-01

    We report on a novel route of preparing molybdena-modified bismuth tungstates and their successful application in the photocatalytic oxygen evolution reaction and the oxidation of glycerol. Hierarchically assembled monocrystalline Bi2WO6 nanoplatelets with a specific surface area of 10 m2/g were

  8. An investigation of the electrochemical action of the epoxy zinc-rich coatings containing surface modified aluminum nanoparticle

    Energy Technology Data Exchange (ETDEWEB)

    Jalili, M. [Nanomaterials and Nanocoatings Department, Institute for Color Science and Technology (ICST), PO 16765-654, Tehran (Iran, Islamic Republic of); Surface Coatings and Corrosion Department, Institute for Color Science and Technology (ICST), PO 16765-654, Tehran (Iran, Islamic Republic of); Rostami, M. [Nanomaterials and Nanocoatings Department, Institute for Color Science and Technology (ICST), PO 16765-654, Tehran (Iran, Islamic Republic of); Ramezanzadeh, B., E-mail: ramezanzadeh-bh@icrc.ac.ir [Surface Coatings and Corrosion Department, Institute for Color Science and Technology (ICST), PO 16765-654, Tehran (Iran, Islamic Republic of)

    2015-02-15

    Highlights: • Aluminum nanoparticle was modified with amino trimethylene phosphonic acid. • 2 wt% of zinc dust in zinc-rich paint was substituted by aluminum nanoparticles. • Surface modified aluminum nanoparticle improved the cathodic period of protection. • Aluminum nanoparticles enhanced the corrosion protection of the zinc-rich coating. - Abstract: Aluminum nanoparticle was modified with amino trimethylene phosphonic acid (ATMP). The surface characterization of the nanoparticles was done by X-ray photo electron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR) and thermal gravimetric analysis. The influence of the replacement of 2 wt% of zinc dust in the standard zinc-rich epoxy coating by nanoparticles on the electrochemical action of the coating was studied by electrochemical impedance spectroscopy (EIS) and salt spray tests. The morphology and phase composition of the zinc rich paints were evaluated by X-ray diffraction (XRD) and filed-emission scanning electron microscopy (FE-SEM). Results showed that the ATMP molecules successfully adsorbed on the surface of Al nanoparticles. Results obtained from salt spray and electrochemical measurements revealed that the addition of surface modified nanoparticles to the zinc rich coating enhanced its galvanic action and corrosion protection properties.

  9. An investigation of the electrochemical action of the epoxy zinc-rich coatings containing surface modified aluminum nanoparticle

    International Nuclear Information System (INIS)

    Jalili, M.; Rostami, M.; Ramezanzadeh, B.

    2015-01-01

    Highlights: • Aluminum nanoparticle was modified with amino trimethylene phosphonic acid. • 2 wt% of zinc dust in zinc-rich paint was substituted by aluminum nanoparticles. • Surface modified aluminum nanoparticle improved the cathodic period of protection. • Aluminum nanoparticles enhanced the corrosion protection of the zinc-rich coating. - Abstract: Aluminum nanoparticle was modified with amino trimethylene phosphonic acid (ATMP). The surface characterization of the nanoparticles was done by X-ray photo electron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR) and thermal gravimetric analysis. The influence of the replacement of 2 wt% of zinc dust in the standard zinc-rich epoxy coating by nanoparticles on the electrochemical action of the coating was studied by electrochemical impedance spectroscopy (EIS) and salt spray tests. The morphology and phase composition of the zinc rich paints were evaluated by X-ray diffraction (XRD) and filed-emission scanning electron microscopy (FE-SEM). Results showed that the ATMP molecules successfully adsorbed on the surface of Al nanoparticles. Results obtained from salt spray and electrochemical measurements revealed that the addition of surface modified nanoparticles to the zinc rich coating enhanced its galvanic action and corrosion protection properties

  10. Control of Surface Modified Layer on Metallic Biomaterials by AN Advanced Elid Grinding System Eg-X

    Science.gov (United States)

    Mizutani, Masayoshi; Komotori, Jun; Katahira, Kazutoshi; Ohmori, Hitoshi

    The biocompatibility of titanium implants with different surface properties is investigated. We prepared three types of specimens, one ground by the newly developed ELID grinding system, another ground by conventional ELID grinding, and the other polished by SiO2 powder. These surfaces were characterized and, the number of cell and cytotoxicity in in-vitro were measured. Energy Dispersive X-ray Spectroscopy (EDS), X-ray Photoelectron Spectroscopy (XPS) and Transmission Electron Microscope (TEM) revealed that the modified ELID system can create a significantly thick oxide layer and a diffused oxide layer, and also can control the thickness of a modified layer. The results of cell number and cytotoxicity showed that the sample ground by the modified system had the highest biocompatibility. This may have been caused by improvement of chemical properties due to a surface modified layer. The above results suggest that this newly developed ELID grinding system can create the desirable surface properties. Consequently, this system appears to offer significant future promise for use in biomaterials and other engineering components.

  11. In-Vitro Comparative Study of In-office and Home Bleaching Agents on Surface Micro-morphology of Enamel.

    Science.gov (United States)

    Fatima, Nazish

    2016-01-01

    To evaluate the effect of home-use bleaching agent containing 16% Carbamide Peroxide (CP) and in-office bleaching agent with 38% Hydrogen Peroxide (HP) on surface micro-morphology of enamel. An experimental study. The discs were prepared at Material Engineering Department of NED University of Engineering and Technology, Karachi, and surface morphology was analyzed at Centralized Science Laboratory of Karachi University, Pakistan. Duration of study was one year from January to December 2012. Forty five sound human third molar crowns, extracted for periodontal reason, were included in the study. Longitudinal sections were made using diamond disks (0.2 mm) under water lubrication to obtain enamel slabs measuring (3 mm x 3 mm). The slabs were embedded in polystyrene resin by using 2.0 cm diameter PVC molds, leaving the outer enamel surface uncovered by the resin. Ninety dental enamel slabs were prepared. The slabs were then randomly divided into 3 groups. Each group contained thirty specimens (n=30). Group 1 was kept in artificial saliva at 37°C in incubator (Memart, Germany) during whole experiment. Group 2 was treated with power whitening gel (White Smile 2011, Germany). Group 3 was treated with tooth whitening pen (White Smile 2011, Germany). The most central region or the region that was most representative of the entire surface area was used. The SEM (Jeol-Japan-JSM6380A, JAPAN) micrographs were examined to determine the type of surface presented. The enamel changes were classified as no or mild alteration, moderate alteration and severe altered surface. Regarding micro-morphology, the enamel surface of control groups showed smooth surface in general with some scattered clear scratches due to the polishing procedure. The specimens bleached in group 2 and group 3, represented areas of mild erosion. Bleaching with 38% Hydrogen Peroxide (HP) and 16% Carbamide Peroxide (CP) resulted in mild changes in surface micro-morphology of enamel.

  12. INFLUENCE OF SURFACE-ACTIVE AGENT CONCENTRATION ON THE SPECTROPHOTOMETRIC BIOMASS ESTIMATION DURING SUBMERGED GROWTH OF Mycobacterium bovis

    Directory of Open Access Journals (Sweden)

    Sakai M.C.

    1997-01-01

    Full Text Available The influence of the surface-active agent Tween 80 (polyoxyethylene 20 sorbitan monoleate on the dispersed growth of Mycobacterium bovis - BCG - was studied. The slopes of the bacterial dry mass / absorbance curves, were significantly reduced, by the increase of the Tween 80 concentration in the medium. Such an influence was probably due to the effect Tween 80 had on the average size of bacterial clumps during the culture carried out in a bench fermenter

  13. A radiobiological approach to cancer treatment. Possible chemical and physical agents modifying radiosensitivity in comparison with high LET radiations

    International Nuclear Information System (INIS)

    Sugahara, T.

    1982-01-01

    Biological characteristics of high LET radiations are summarized to be low oxygen enhancement ratio, high RBE, low repair and low cell cycle dependency of radiosensitivity. Various chemical modifiers of radiosensitivity and radiological effect of hyperthermia are classified into these four properties. It is evident that we have now various means to mimic high LET radiations as far as biological response is concerned though some of them are still in experimental stage. Among them, the means to cope with hypoxia and repair which are assumed to be the most important causes of radioresistance of human tumors are discussed in some detail. It is expected that through the present seminar we would have consensus to concentrate our effort of development for new modifying means available and useful in developing countries. (author)

  14. Use of Modified Phenolic Thyme Extracts (Thymus vulgaris) with Reduced Polyphenol Oxidase Substrates as Anthocyanin Color and Stability Enhancing Agents.

    Science.gov (United States)

    Aguilar, Oscar; Hernández-Brenes, Carmen

    2015-12-14

    Residual enzymatic activity in certain foods, particularly of polyphenoloxidase (PPO), is responsible for the majority of anthocyanin degradation in food systems, causing also parallel losses of other relevant nutrients. The present work explored the feasibility of modifying phenolic profiles of thyme extracts, by use of chromatographic resins, to obtain phenolic extracts capable of enhancing anthocyanin colour and stability in the presence of PPO activity. Results indicated that pretreatment of thyme extracts with strong-anion exchange resins (SAE) enhanced their copigmentation abilities with strawberry juice anthocyanins. Phenolic chromatographic profiles, by HPLC-PDA, also demonstrated that thyme extracts subjected to SAE treatments had significantly lower concentrations of certain phenolic compounds, but extracts retained their colour enhancing and anthocyanin stabilization capacities though copigmentation. Additional testing also indicated that SAE modified extract had a lower ability (73% decrease) to serve as PPO substrate, when compared to the unmodified extract. Phenolic profile modification process, reported herein, could be potentially used to manufacture modified anthocyanin-copigmentation food and cosmetic additives for colour-stabilizing applications with lower secondary degradation reactions in matrixes that contain PPO activity.

  15. Use of Modified Phenolic Thyme Extracts (Thymus vulgaris with Reduced Polyphenol Oxidase Substrates as Anthocyanin Color and Stability Enhancing Agents

    Directory of Open Access Journals (Sweden)

    Oscar Aguilar

    2015-12-01

    Full Text Available Residual enzymatic activity in certain foods, particularly of polyphenoloxidase (PPO, is responsible for the majority of anthocyanin degradation in food systems, causing also parallel losses of other relevant nutrients. The present work explored the feasibility of modifying phenolic profiles of thyme extracts, by use of chromatographic resins, to obtain phenolic extracts capable of enhancing anthocyanin colour and stability in the presence of PPO activity. Results indicated that pretreatment of thyme extracts with strong-anion exchange resins (SAE enhanced their copigmentation abilities with strawberry juice anthocyanins. Phenolic chromatographic profiles, by HPLC-PDA, also demonstrated that thyme extracts subjected to SAE treatments had significantly lower concentrations of certain phenolic compounds, but extracts retained their colour enhancing and anthocyanin stabilization capacities though copigmentation. Additional testing also indicated that SAE modified extract had a lower ability (73% decrease to serve as PPO substrate, when compared to the unmodified extract. Phenolic profile modification process, reported herein, could be potentially used to manufacture modified anthocyanin-copigmentation food and cosmetic additives for colour-stabilizing applications with lower secondary degradation reactions in matrixes that contain PPO activity.

  16. Study of removing a peat-layer from surface active agents; Deitanso ni yoru kaimen kasseizai no jokyo

    Energy Technology Data Exchange (ETDEWEB)

    Umemiya, H.; Kitamura, K. [Yamagata University, Yamagata (Japan)

    1996-10-27

    An experiment was performed on a system for recycling water resources by using a peat-layer. A laboratory device was also made in order to examine the effects of a peat-layer on surface active agents. In the experiment, a water examination was carried out in which a mixture of water and kitchen detergent at the rate of 15,000 to 1 was filtered through a peat-layer of 2-3cm thick, as was a mixture of water, kitchen detergent and oil at the rate of 15,000 to 1 to 2. In the water examination, various measurements were done such as the measurement of COD by potassium permanganate acid process, measurement of pH by a pH meter with glass electrodes and measurement of coefficient of permeability by a variable water level permeability test. As a result of the experiment, it was revealed that a peat-layer had ability to remove surface active agents, that injection water tended to increase acidity in a peat-layer and that a peat-layer had ability to remove foaming of surface active agents. The COD of domestic waste water decreased from 12mg/l to 0.16mg/l in the system for recycling water resources using a peat-layer. 3 refs., 10 figs., 1 tab.

  17. Electrochemical Cathodic Polarization, a Simplified Method That Can Modified and Increase the Biological Activity of Titanium Surfaces: A Systematic Review.

    Directory of Open Access Journals (Sweden)

    Jose Carlos Bernedo Alcazar

    Full Text Available The cathodic polarization seems to be an electrochemical method capable of modifying and coat biomolecules on titanium surfaces, improving the surface activity and promoting better biological responses.The aim of the systematic review is to assess the scientific literature to evaluate the cellular response produced by treatment of titanium surfaces by applying the cathodic polarization technique.The literature search was performed in several databases including PubMed, Web of Science, Scopus, Science Direct, Scielo and EBSCO Host, until June 2016, with no limits used. Eligibility criteria were used and quality assessment was performed following slightly modified ARRIVE and SYRCLE guidelines for cellular studies and animal research.Thirteen studies accomplished the inclusion criteria and were considered in the review. The quality of reporting studies in animal models was low and for the in vitro studies it was high. The in vitro and in vivo results reported that the use of cathodic polarization promoted hydride surfaces, effective deposition, and adhesion of the coated biomolecules. In the experimental groups that used the electrochemical method, cellular viability, proliferation, adhesion, differentiation, or bone growth were better or comparable with the control groups.The use of the cathodic polarization method to modify titanium surfaces seems to be an interesting method that could produce active layers and consequently enhance cellular response, in vitro and in vivo animal model studies.

  18. A Simple, Cost-Efficient Method to Separate Microalgal Lipids from Wet Biomass Using Surface Energy-Modified Membranes.

    Science.gov (United States)

    Kwak, Moo Jin; Yoo, Youngmin; Lee, Han Sol; Kim, Jiyeon; Yang, Ji-Won; Han, Jong-In; Im, Sung Gap; Kwon, Jong-Hee

    2016-01-13

    For the efficient separation of lipid extracted from microalgae cells, a novel membrane was devised by introducing a functional polymer coating onto a membrane surface by means of an initiated chemical vapor deposition (iCVD) process. To this end, a steel-use-stainless (SUS) membrane was modified in a way that its surface energy was systemically modified. The surface modification by conformal coating of functional polymer film allowed for selective separation of oil-water mixture, by harnessing the tuned interfacial energy between each liquid phase and the membrane surface. The surface-modified membrane, when used with chloroform-based solvent, exhibited superb permeate flux, breakthrough pressure, and also separation yield: it allowed separation of 95.5 ± 1.2% of converted lipid (FAME) in the chloroform phase from the water/MeOH phase with microalgal debris. This result clearly supported that the membrane-based lipid separation is indeed facilitated by way of membrane being functionalized, enabling us to simplify the whole downstream process of microalgae-derived biodiesel production.

  19. Understanding long-term silver release from surface modified porous titanium implants.

    Science.gov (United States)

    Shivaram, Anish; Bose, Susmita; Bandyopadhyay, Amit

    2017-08-01

    Prevention of orthopedic device related infection (ODRI) using antibiotics has met with limited amount of success and is still a big concern during post-surgery. As an alternative, use of silver as an antibiotic treatment to prevent surgical infections is being used due to the well-established antimicrobial properties of silver. However, in most cases silver is used in particulate form with wound dressings or with short-term devices such as catheters but not with load-bearing implants. We hypothesize that strongly adherent silver to load-bearing implants can offer longer term solution to infection in vivo. Keeping that in mind, the focus of this study was to understand the long term release study of silver ions for a period of minimum 6months from silver coated surface modified porous titanium implants. Implants were fabricated using a LENS™ system, a powder based additive manufacturing technique, with at least 25% volume porosity, with and without TiO 2 nanotubes in phosphate buffer saline (pH 7.4) to see if the total release of silver ions is within the toxic limit for human cells. Considering the fact that infection sites may reduce the local pH, silver release was also studied in acetate buffer (pH 5.0) for a period of 4weeks. Along with that, the osseointegrative properties as well as cytotoxicity of porous titanium implants were assessed in vivo for a period of 12weeks using a rat distal femur model. In vivo results indicate that porous titanium implants with silver coating show comparable, if not better, biocompatibility and bonding at the bone-implant interface negating any concerns related to toxicity related to silver to normal cells. The current research is based on our recently patented technology, however focused on understanding longer-term silver release to mitigate infection related problems in load-bearing implants that can even arise several months after the surgery. Prevention of orthopedic device related infection using antibiotics has met

  20. An investigation of the electrochemical action of the epoxy zinc-rich coatings containing surface modified aluminum nanoparticle

    Science.gov (United States)

    Jalili, M.; Rostami, M.; Ramezanzadeh, B.

    2015-02-01

    Aluminum nanoparticle was modified with amino trimethylene phosphonic acid (ATMP). The surface characterization of the nanoparticles was done by X-ray photo electron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR) and thermal gravimetric analysis. The influence of the replacement of 2 wt% of zinc dust in the standard zinc-rich epoxy coating by nanoparticles on the electrochemical action of the coating was studied by electrochemical impedance spectroscopy (EIS) and salt spray tests. The morphology and phase composition of the zinc rich paints were evaluated by X-ray diffraction (XRD) and filed-emission scanning electron microscopy (FE-SEM). Results showed that the ATMP molecules successfully adsorbed on the surface of Al nanoparticles. Results obtained from salt spray and electrochemical measurements revealed that the addition of surface modified nanoparticles to the zinc rich coating enhanced its galvanic action and corrosion protection properties.

  1. METABOLIC AND MORPHOLOGICAL OBSERVATIONS ON THE EFFECT OF SURFACE-ACTIVE AGENTS ON LEUKOCYTES

    Science.gov (United States)

    Graham, R. C.; Karnovsky, M. J.; Shafer, A. W.; Glass, E. A.; Karnovsky, Manfred L.

    1967-01-01

    Morphological and metabolic observations have been made on the effects of endotoxin, deoxycholate, and digitonin (at less than 50 µg/ml) on polymorphonuclear leukocytes and mononuclear cells. The agents stimulate the respiration and glucose oxidation of these cells in a manner similar to that seen during phagocytosis. Electron microscopy revealed no morphological changes with the first two agents, but dramatic membrane changes were seen in the case of digitonin. Here tubular projections of characteristic size and shape formed on and split off the membrane. All the agents stimulated uptake of inulin, but efforts to demonstrate increased pinocytosis by electron microscopy have not so far succeeded, probably due to limitations in present experimental techniques. PMID:6034482

  2. Surface with two paint strips for detection and warning of chemical warfare and radiological agents

    Science.gov (United States)

    Farmer, Joseph C.

    2013-04-02

    A system for warning of corrosion, chemical, or radiological substances. The system comprises painting a surface with a paint or coating that includes an indicator material and monitoring the surface for indications of the corrosion, chemical, or radiological substances.

  3. Surface modification of halloysite nanotubes by vulcanization accelerator and properties of styrene-butadiene rubber nanocomposites with modified halloysite nanotubes

    Energy Technology Data Exchange (ETDEWEB)

    Zhong, Bangchao; Jia, Zhixin, E-mail: zxjia@scut.edu.cn; Hu, Dechao; Luo, Yuanfang; Guo, Baochun; Jia, Demin

    2016-03-15

    Graphical abstract: - Highlights: • Vulcanization accelerant was used to modify halloysite nanotubes (HNTs). • The modified HNTs reduced the activation energy of vulcanization. • Strong filler–rubber interaction was achieved in rubber/modified HNTs composites. • The modified HNTs exhibited excellent reinforcement effect on rubber. - Abstract: Vulcanization accelerant N-cyclohexyl-2-benzothiazole sulfenamide (CZ) was used as a surface modifier and chemically grafted on the surface of halloysite nanotubes (HNTs) to obtain CZ-functionalized HNTs (HNTs-s-CZ). It was found that HNTs-s-CZ could be homogeneously dispersed into styrene-butadiene rubber (SBR). The grafted CZ molecules, exactly located at the filler-rubber interface, reduced the activation energy of vulcanization of SBR/HNTs-s-CZ compounds. Besides, the density of chain segments introduced by the interfacial phase of SBR/HNTs-s-CZ nanocomposites was higher than the other nanocomposites with silane-modified HNTs (m-HNTs) or pristine HNTs, manifesting an indication of enhanced filler-rubber interfacial interaction in SBR/HNTs-s-CZ nanocomposites. Consequently, SBR/HNTs-s-CZ nanocomposites showed excellent mechanical properties. The tensile strength could be enhanced by as much as 38.6% and 102.5% compared to those of SBR/m-HNTs and SBR/HNTs nanocomposites, respectively, though containing equivalent accelerant component. The value of this work lies in the fact that apparent properties improvement of elastomer composites has been achieved by the incorporation of vulcanization accelerant-functionalized HNTs, which may be fruitful for the rational design of filler surface treatment and offer new scientific and technological opportunities for the preparation of high performance elastomer composites.

  4. Kenaf-polypropylene composites: effect of amphiphilic coupling agent on surface properties of fibres and composites

    CSIR Research Space (South Africa)

    Jacob John, Maya

    2010-10-01

    Full Text Available of Science, Nelson Mandela Metropolitan University, P.O. 9 Box 1600, Port Elizabeth 6000, South Africa, 10 E-mail: ranandi@csir.co.za,Rajesh.Anandjiwala@nmmu.ac.za 11 3 Leibniz Institut of Polymer Research Dresden, Department Polymer Interfaces, D-01069... Dresden, 12 Germany 13 14 Abstract 15 This paper presents an experimental study on the use of zein as a coupling agent in 16 natural fibre composites. Kenaf nonwovens were treated with zein coupling agent, 17 which is a protein extracted from corn...

  5. Construction of multi-agent mobile robots control system in the problem of persecution with using a modified reinforcement learning method based on neural networks

    Science.gov (United States)

    Patkin, M. L.; Rogachev, G. N.

    2018-02-01

    A method for constructing a multi-agent control system for mobile robots based on training with reinforcement using deep neural networks is considered. Synthesis of the management system is proposed to be carried out with reinforcement training and the modified Actor-Critic method, in which the Actor module is divided into Action Actor and Communication Actor in order to simultaneously manage mobile robots and communicate with partners. Communication is carried out by sending partners at each step a vector of real numbers that are added to the observation vector and affect the behaviour. Functions of Actors and Critic are approximated by deep neural networks. The Critics value function is trained by using the TD-error method and the Actor’s function by using DDPG. The Communication Actor’s neural network is trained through gradients received from partner agents. An environment in which a cooperative multi-agent interaction is present was developed, computer simulation of the application of this method in the control problem of two robots pursuing two goals was carried out.

  6. Comparison between silver- and copper-modified zeolite-rich tuffs as microbicide agents for Escherichia coli and Candida albicans.

    Science.gov (United States)

    Rossainz-Castro, L G; De-La-Rosa-Gómez, I; Olguín, M T; Alcántara-Díaz, D

    2016-12-01

    Zeolite-rich tuff from the State of Chihuahua was modified with silver or copper ions (ZChAg and ZChCu) to evaluate its microbicidal effect against Escherichia coli (E. coli) and Candida albicans (C. albicans) suspended in an aqueous solution in order to compare the microbial disinfection kinetics between bacteria and yeast. The zeolite-rich tuff was treated with AgNO 3 or CuCl 2 solutions. The materials obtained were characterized using scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD) and the textural properties were also determined by BET-analyses. The concentration of Ag and Cu was verified in the zeolitic materials using neutron activation analysis. The experimental data were adjusted to both Chick and Chik-Watson models to describe the kinetic behavior of the process. It was found that when the mass of ZChAg increased, the survival microorganisms notably decreased. The E. coli and C. albicans showed higher resistance in contact with ZChCu even when the mass of such material was 10-20 times higher than the mass of ZChAg. Chick and Chik-Watson constants showed that the kinetics of the disinfection process depended on the desorption of the exchange ion that modified the structure of the zeolitic material, its concentration in aqueous medium, its oligodynamic properties, and each microorganism's characteristics (Gram-negative bacteria and yeast). The kinetic desorption of Ag and Cu from the corresponding modified-zeolite-rich tuffs was also considered in this work. In this case, the Higuchi and Korsmeyer-Peppas models were applied. Copyright © 2016 Elsevier Ltd. All rights reserved.

  7. Biology of human skin transplanted to the nude mouse: I. Response to agents which modify epidermal proliferation.

    Science.gov (United States)

    Krueger, G G; Shelby, J

    1981-06-01

    To accept human skin transplanted to the congenitally athymic (nude) mouse as a system to study human skin and its physiologic and pathologic states, it must be demonstrated that skin so maintained retains its function as a biologic unit. We have found that responses of grafted human skin and nude mouse skin to various agents differ. This difference in response has been utilized to assess barrier function and proliferative capacity of human skin grafts. Human skin grafts undergo a proliferative response when 10 ng of the tumor promoter, 12-O-tetradecanoyl phorbol 13-acetate (TPA) is applied. Nudes do not respond to this dose. Increasing the dose to 100 ng of TPA evokes a response in both. However, only in the human skin grafts can this response be blocked with betamethasone valerate (BV). In that human skin grafts do not take on their hosts' responsiveness, and the response of domestic pig skin to these agents before and after grafting is identical, the conclusion is reached that human skin appears to retain its inherent biologic unit function. The data also demonstrate some of the potential of this system to study kinetics of the epidermis of human skin.

  8. Heterogeneous freezing of droplets with immersed surface modified mineral dust particles

    Science.gov (United States)

    Hartmann, Susan

    2010-05-01

    In the framework of the international measurement campaign FROST II (FReezing Of duST), the heterogeneous freezing of droplets with an immersed surface modified size-segregated mineral dust particles was investigated at LACIS (Leipzig Aerosol Cloud Interaction Simulator, Stratmann et al. 2004). The following measurements were done: LACIS, CFDC (Continuous Flow thermal gradient Diffusion Chamber, Rogers (1988)) and FINCH (Fast Ice Nucleus Chamber Counter, Bundke et al (2008)) were used to analyze the immersion freezing behavior of the treated Arizona Test Dust (ATD) particles at different temperature regimes. The ability to act as IN (Ice Nucleus) in the deposition nucleation mode was quantified by the PINC (Portable Ice Nucleation Chamber) and the CFDC instrument. AMS (Aerosol Mass Spectrometers, e.g. Schneider et al. (2005)) and ATOFMS (Aerosol Time-Of-Flight Mass Spectrometer) measurements were applied to determine particle composition. The hygroscopic growth and the critical super-saturations needed for droplet activation were determined by means of an H-TDMA (Humidity-Tandem Differential Mobility Analyzer) and CCN counter (Cloud Condensation Nucleus counter, Droplet Measurement Technologies, Roberts and Nenes (2005)). The 300 nm ATD particles were chemically and physically treated by coating with sulphuric acid (H2SO4, three different coating thicknesses) and ammonium sulphate ((NH4)2SO4) or by thermal treatment with a thermodenuder operating at 250°C. The H2SO4 coating modified the particles by reacting with particle material, forming soluble sulfates and therefore changing surface properties. AMS showed free H2SO4 only for thick H2SO4 coatings. In the heated section of the thermodenuder coating materials were evaporated partly and the surface properties of the particles were additionally altered. Uncoated particles and those coated with thin coatings of H2SO4, showed almost no hygroscopic growth. Particles coated with thicker coatings of H2SO4 and of (NH4

  9. Effect on Concrete Surface Water Absorption upon Addition of Lactate Derived Agent

    NARCIS (Netherlands)

    Mors, R.M.; Jonkers, H.M.

    2017-01-01

    Water tightness of a concrete cover layer is important, as it is typically used as a protective coating of the steel reinforcement. Water tightness can be impaired by crack formation or by permeability. A bacteria-based lactate-derived healing agent (HA) can be added to concrete to enhance the

  10. Use of silane coupling agent for surface modification of zinc oxide as ...

    Indian Academy of Sciences (India)

    contain phenylalanine amino acid and ZnO, they are expected to be biocompatible as well as biodegradable. Keywords. Poly(amide–imide); nanocomposite; coupling agent;γ-aminopropyltriethoxysilane; ZnO nanoparticles. 1. Introduction. Nanocomposites of nanoscale inorganic semiconductors and organic host polymers ...

  11. Two component silicone modified epoxy foul release coatings: Effect of modulus, surface energy and surface restructuring on pseudobarnacle and macrofouling behavior

    International Nuclear Information System (INIS)

    Rath, S.K.; Chavan, J.G.; Sasane, Savita; Jagannath; Patri, M.; Samui, A.B.; Chakraborty, B.C.

    2010-01-01

    Two component silicone modified epoxy resin based low surface energy and non-toxic foul release coatings were developed. Silicone modified epoxy resin with 15 and 30% silicone content was used as component A and a polyether diamine (Jeffamine-500) was used as the component B. Free standing films were prepared by casting a mixture of components A and B in stoichiometric proportions. The surface composition, surface topography and wetting properties of the coatings were studied by angle resolved X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM) and contact angle goniometry respectively. The mechanical properties of the cured films were evaluated by tensile measurements as well as dynamic mechanical analysis. Pseudobarnacles made of aluminium studs were attached to the coated panels and adhesion tests were carried out by a pseudobarnacle tester. Coated panels were exposed in Mumbai harbor for fouling studies for a period of 90 days. Surface restructuring studies of the coatings upon immersion in seawater were carried out by measuring the changes in advancing and receding contact angles by contact angle goniometry. The effect of surface energy, modulus and surface restructuring of the coatings on the macrofouling and pseudobarnacle adhesion properties has been discussed in detail.

  12. Characteristics of surface modified Ti-6Al-4V alloy by a series of YAG laser irradiation

    Science.gov (United States)

    Zeng, Xian; Wang, Wenqin; Yamaguchi, Tomiko; Nishio, Kazumasa

    2018-01-01

    In this study, a double-layer Ti (C, N) film was successfully prepared on Ti-6Al-4V alloy by a series of YAG laser irradiation in nitrogen atmosphere, aiming at improving the wear resistance. The effects of laser irradiation pass upon surface chemical composition, microstructures and hardness were investigated. The results showed that the surface chemicals were independent from laser irradiation pass, which the up layer of film was a mixture of TiN and TiC0.3N0.7, and the down layer was nitrogen-rich α-Ti. Both the surface roughness and hardness increased as raising the irradiation passes. However, surface deformation and cracks happened in the case above 3 passes' irradiation. The wear resistance of laser modified sample by 3 passes was improved approximately by 37 times compared to the as received substrate. Moreover, the cytotoxic V ion released from laser modified sample was less than that of as received Ti-6Al-4V alloy in SBF, suggesting the potentiality of a new try to modify the sliding part of Ti-based hard tissue implants in future biomedical application.

  13. The influence of the addition of dye surface modifier on the performance of transparent dye sensitized solar cells

    Science.gov (United States)

    Rosa, Erlyta Septa; Shobih, Retnaningsih, Lilis; Muliani, Lia; Hidayat, Jojo

    2017-11-01

    The light-harvesting properties and charge injection kinetics of dye molecules play a significant role to improve the performance of dye-sensitized solar cells (DSSC). Dyes based on metal complexes with ruthenium complexes also a variety of metal-organic dyes such as Zn-porphyrin derivatives have been used. The requirements for dye to function as a photosensitizer in DSSC are the absorption in the visible or near-infrared regions of the solar spectrum and the binding to the semiconductor TiO2. In order to interact with the TiO2 surface it is preferable that the dye has a functional group as anchoring group such as carboxylic or other peripheral acidic. The carboxylic group is the most frequently used anchoring group, as in ruthenium-complex based dyes. However, carboxylic acid as an anchoring group is still not enough for conducting in electron injection to TiO2. In this research, 0.87 mg phosphonic acid is added to N719 and Z907 ruthenium-complex based dyes, rspectively, as a surface modifier to strengthen the anchoring group. The addition of dyes surface modifier on the transparent DSSC device performance is investigated. Under illumination of 500 Wm-2, the power conversion efficiency (PCE) of DSSC using N719 ruthenium increases from 2.09 % to 3.22 % by the addition of surface modifier. However, different results are obtained on Z907 dye, where efficiency decreases from 2.02 % to 1.58 %.

  14. Polymer films with surfaces unmodified and modified by non-thermal plasma as new substrates for cell adhesion

    Energy Technology Data Exchange (ETDEWEB)

    Borges, A.M.G.; Benetoli, L.O. [Department of Chemistry, Federal University of Santa Catarina, 88040-900 Florianopolis (Brazil); Licínio, M.A. [Department of Clinical Analysis, Federal University of Santa Catarina, 88040-900 Florianopolis (Brazil); Zoldan, V.C. [Department of Physical, Federal University of Santa Catarina, 88040-900 Florianopolis (Brazil); Santos-Silva, M.C. [Department of Clinical Analysis, Federal University of Santa Catarina, 88040-900 Florianopolis (Brazil); Assreuy, J. [Department of Pharmacology, Federal University of Santa Catarina, 88040-900 Florianopolis (Brazil); Pasa, A.A. [Department of Physical, Federal University of Santa Catarina, 88040-900 Florianopolis (Brazil); Debacher, N.A. [Department of Chemistry, Federal University of Santa Catarina, 88040-900 Florianopolis (Brazil); Soldi, V., E-mail: vsoldi@pq.cnpq.br [Department of Chemistry, Federal University of Santa Catarina, 88040-900 Florianopolis (Brazil)

    2013-04-01

    The surface properties of biomaterials, such as wettability, polar group distribution, and topography, play important roles in the behavior of cell adhesion and proliferation. Gaseous plasma discharges are among the most common means to modify the surface of a polymer without affecting its properties. Herein, we describe the surface modification of poly(styrene) (PS) and poly(methyl methacrylate) (PMMA) films using atmospheric pressure plasma processing through exposure to a dielectric barrier discharge (DBD). After treatment the film surface showed significant changes from hydrophobic to hydrophilic as the water contact angle decreasing from 95° to 37°. All plasma-treated films developed more hydrophilic surfaces compared to untreated films, although the reasons for the change in the surface properties of PS and PMMA differed, that is, the PS showed chemical changes and in the case of PMMA they were topographical. Excellent adhesion and cell proliferation were observed in all films. In vitro studies employing flow cytometry showed that the proliferation of L929 cells was higher in the film formed by a 1:1 mixture of PS/PMMA, which is consistent with the results of a previous study. These findings suggest better adhesion of L929 onto the 1:1 PS/PMMA modified film, indicating that this system is a new candidate biomaterial for tissue engineering. Highlights: ► The PS/PMMA films showed hydrophilic surface after DBD-treatment. ► The 1:1 PS/PMMA modified film is a new substrate for L929 cell proliferation. ► The 1:1 PS/PMMA blend film showed additional 170 × 10{sup 3} cells after treatment. ► The proliferation of cells in the blend film triplicated when compared to control. ► Synergistic effect improves cell proliferation in the blend film.

  15. Visual detection of a nerve agent simulant using chemically modified paper strips and dye-assembled inorganic nanocomposite.

    Science.gov (United States)

    Dey, Nilanjan; Jha, Satadru; Bhattacharya, Santanu

    2018-01-15

    Chromogenic probe with oxidized bis-indolyl scaffold has been synthesized for the detection of a nerve gas mimicking agent, DCNP (diethyl cyanophosphonate) at pH 8.0 in water. The mechanism of interaction was proposed as the release of cyanide ion through the indole group mediating the hydrolysis of phosphorous-hetero atom bond and, thereafter, the Michael addition of the liberated CN - ion to the electron deficient C[double bond, length as m-dash]C bond of the bis-indolyl moiety. The reaction featured a remarkable change in color from red to colorless at ambient condition. Then, low-cost and portable paper strips were designed for a rapid and on-site vapor phase detection of DCNP without involving any sophisticated instrument or skilled personnel. Finally, a dye assembled inorganic nanocomposite material was devised to achieve a more sensitive 'turn-on' detection of DCNP in water.

  16. Reciprocating Sliding Behaviour of Solid Lubricant Coating over Modified Titanium Alloy Surfaces

    Science.gov (United States)

    Jothi Prakash, V. M.; Sathish, S.; Gopalakrishnan, T.; Venugopal, S.

    2017-03-01

    Tribological behaviour of contacting surfaces rigid sphere is using flat plate the with influence of normal and tangential loading (shear traction) is analysed using FEA model and surfaces being coated on flat plate by Titanium Alloy, Aluminium Alloy Molybdenum Di-sulphide. The finite element model facilitates to Evaluating the surface variables like contact stress distribution with the surface level and surface, contact pressure, shear stress and displacement. The finite element solution is validated through the hertz solution and on the successful verification.

  17. The effect of surface modification of glass fiber on the performance of poly(lactic acid) composites: Graphene oxide vs. silane coupling agents

    Science.gov (United States)

    Jing, Mengfan; Che, Junjin; Xu, Shuman; Liu, Zhenwei; Fu, Qiang

    2018-03-01

    In this work, a comparison study was carried out to investigate the efficacy of glass fiber (GF) in reinforcing poly(lactic acid) (PLA) by using traditional silane coupling agents (GF-S) and novel graphene oxide (GF-GO) as surface modifiers. The crystallization behavior of the PLA matrix was investigated by differential scanning calorimetry. The mechanical performances and the thermomechanical properties of the composites were evaluated by uniaxial tensile testing and dynamic mechanical analysis, respectively. For neat GF without any treatment, the poor interfacial adhesion and the sharp shortening of the GF length result in the relatively poor mechanical performances of PLA/GF composites. However, the incorporation of GF-S significantly improves the mechanical strength and keeps relatively good toughness of the composites, while GF-GO exhibits excellent nucleation ability for PLA and could moderately increase the modulus of the composites. The thermomechanical properties of the composites are improved markedly resulting from the crystallinity increase. The different surface modification of glass fiber influences the crystallinity of matrix, the interfacial interaction and the length of fiber, which altogether affect the mechanical performances of the prepared PLA/GF composites.

  18. Annual Report 2013-2014: Theoretical Studies of Nerve Agents Adsorbed on Surfaces

    Science.gov (United States)

    2014-07-08

    Photoassisted removal of sarin vapor in air under UV light irradiation. Journal of Photochemistry and Photobiology a- Chemistry 2007, 188, 143-148...with an ester linkage to an aliphatic group. Coloring scheme as follows: C (gray), H (white), O (red), P (orange), F ( blue ). Most nerve agents act...magnesium oxide. Journal of Physical Chemistry B 2004, 108, 5294-5303. 7. Michalkova, A.; Paukku, Y .; Majumdar, D.; Leszczynski, J., Theoretical study

  19. Screen-printed carbon electrode modified on its surface with amorphous carbon nitride thin film: Electrochemical and morphological study

    Energy Technology Data Exchange (ETDEWEB)

    Ghamouss, F. [Universite de Nantes, UMR 6006-CNRS, FR-2465-CNRS, Laboratoire d' Analyse isotopique et Electrochimique de Metabolismes (LAIEM) (France); Tessier, P.-Y. [Universite de Nantes, UMR CNRS 6502, Institut des Materiaux Jean Rouxel - IMN Faculte des Sciences and des Techniques de Nantes, 2 rue de la Houssiniere, 44322 Nantes Cedex 3 (France); Djouadi, A. [Universite de Nantes, UMR CNRS 6502, Institut des Materiaux Jean Rouxel - IMN Faculte des Sciences and des Techniques de Nantes, 2 rue de la Houssiniere, 44322 Nantes Cedex 3 (France); Besland, M.-P. [Universite de Nantes, UMR CNRS 6502, Institut des Materiaux Jean Rouxel - IMN Faculte des Sciences and des Techniques de Nantes, 2 rue de la Houssiniere, 44322 Nantes Cedex 3 (France); Boujtita, M. [Universite de Nantes, UMR 6006-CNRS, FR-2465-CNRS, Laboratoire d' Analyse isotopique et Electrochimique de Metabolismes (LAIEM) (France)]. E-mail: mohammed.boujtita@univ-nantes.fr

    2007-04-20

    The surface of a screen-printed carbon electrode (SPCE) was modified by using amorphous carbon nitride (a-CN {sub x}) thin film deposited by reactive magnetron sputtering. Scanning electron microscopy and photoelectron spectroscopy measurements were used to characterise respectively the morphology and the chemical structure of the a-CN {sub x} modified electrodes. The incorporation of nitrogen in the amorphous carbon network was demonstrated by X ray photoelectron spectroscopy. The a-CN {sub x} layers were deposited on both carbon screen-printed electrode (SPCE) and silicon (Si) substrates. A comparative study showed that the nature of substrate, i.e. SPCE and Si, has a significant effect on both the surface morphology of deposited a-CN {sub x} film and their electrochemical properties. The improvement of the electrochemical reactivity of SPCE after a-CN {sub x} film deposition was highlighted both by comparing the shapes of voltammograms and calculating the apparent heterogeneous electron transfer rate constant.

  20. Poly(vinyl chloride) catheters modified with pH-responsive poly(methacrylic acid) with affinity for antimicrobial agents

    Science.gov (United States)

    Zuñiga-Zamorano, Ivette; Meléndez-Ortiz, H. Iván; Costoya, Alejandro; Alvarez-Lorenzo, Carmen; Concheiro, Angel; Bucio, Emilio

    2018-01-01

    Radiation-grafting of pH-responsive methacrylic acid (MAA) onto poly(vinyl chloride) (PVC) was carried out by the pre-irradiation method using gamma rays, which demonstrated to be an efficient and fast procedure for obtaining PVC-g-MAA copolymers. The influence of preparation conditions, such as absorbed dose, monomer concentration, reaction time, and reaction temperature on the grafting yield was studied. The grafting of MAA onto PVC catheters was confirmed by means of Fourier transform infrared spectroscopy (FT-IR), thermogravimetry analysis (TGA), and differential scanning calorimetry (DSC). The pH-responsiveness of the grafted copolymers (critical point 8.5) was measured by swelling under cyclic changes in the pH of the medium. Interestingly, PVC-g-MAA showed enhanced capability to immobilize benzalkonium chloride and, particularly, ciprofloxacin and to sustain the release this antimicrobial agent at both acid and alkaline pH. Tests carried out with Escherichia coli, Pseudomonas aeruginosa, and Staphylococcus aureus point out that the developed functionalized catheters may play a role in the prevention/management of urinary tract infections.

  1. Surface modification of BMN particles with silane coupling agent for composites with PTFE

    Science.gov (United States)

    Qi, Yanyuan; Luo, Qing; Shen, Jie; Zheng, Liu; Zhou, Jing; Chen, Wen

    2017-08-01

    Polymer-ceramic dielectric composites, which possess better dielectric properties, flexibility, ease in processing and shaping since they combine the advantages of polymers and dielectric ceramics, are widely used in microwave substrate applications. In order to optimize the properties of the composites, it is necessary to enhance the compatibility between the polymer matrix and ceramic filler because of their tremendous difference. In this paper, the vinyltrimethoxysilane (VTMS) is used to modify the Ba(Mg1/3Nb2/3)O3 (BMN) ceramic particles which can improve the compatibility between BMN ceramics and PTFE and the distribution of BMN in polytetrafluoroethylene (PTFE). The modification of VTMS has no influence on the crystal structure of BMN ceramics and the compact VTMS modified BMN/PTFE composites with satisfactory uniformity and less cavities are obtained. The relative permittivity (εr) of VTMS modified BMN/PTFE composite substrate is 5.84 while the loss tangent reaches 1.5 × 10-3 at microwave frequencies (around 10 GHz).

  2. Functionalization of poly(ε-caprolactone) surface with lactose-modified chitosan via alkaline hydrolysis: ToF-SIMS characterization.

    Science.gov (United States)

    Tortora, Luca; Concolato, Sofia; Urbini, Marco; Giannitelli, Sara Maria; Basoli, Francesco; Rainer, Alberto; Trombetta, Marcella; Orsini, Monica; Mozetic, Pamela

    2016-06-23

    Functionalization of poly(ε-caprolactone) (PCL) was performed via hydrolysis and subsequent grafting of lactose-modified chitosan (chitlac) at two different degrees of derivatization (9% and 64%). Time of flight secondary ion mass spectrometry (ToF-SIMS) and multivariate analysis (principal component analysis) were successfully applied to the characterization of PCL surface chemistry, evidencing changes in the biopolymer surface following base-catalyzed hydrolysis treatment. ToF-SIMS analysis also confirmed positive EDC/NHS-catalyzed (EDC: N-ethyl-N'-(3-(dimethylamino)propyl)carbodiimide; NHS: N-hydroxysuccinimide) immobilization of chitlac onto activated PCL surface, with formation of amide bonds between PCL surface carboxyl groups and amine residues of chitlac. Yield of grafting reaction was also shown to be dependent upon the lactosilation degree of chitlac.

  3. Au nanoparticle-modified DNA sensor based on simultaneous electrochemical impedance spectroscopy and localized surface plasmon resonance.

    Science.gov (United States)

    Cheng, Xin R; Hau, Ben Y H; Endo, Tatsuro; Kerman, Kagan

    2014-03-15

    Electrochemical impedance spectroscopy (EIS) and localized surface plasmon resonance (LSPR) were performed on the same Au nanoparticle (AuNP)-modified indium tin oxide (ITO) coated glass surfaces. Cyclic voltammetry was applied to electrodeposit AuNPs on ITO surface directly. The surface plasmon band characterization of AuNPs was initially studied by controlling the electrodeposition conditions. It was found that the size of AuNP clusters was significantly affected by the applied potential and KCl concentration in solution. The dual-detection platform was applied to detect DNA hybridization related to a specific point mutation in apolipoprotein E gene (ApoE), which was related to the progression of Alzheimer's disease. The preliminary results facilitate the development of a versatile biosensor that can be easily miniaturized and integrated into a high-throughput diagnostic device. © 2013 Elsevier B.V. All rights reserved.

  4. Competitive Adsorption of Plasma Proteins on Polysaccharide-Modified Silicon Surfaces

    National Research Council Canada - National Science Library

    Ombelli, Michela; Costello, Lauren B; Meng, Qing C; Composto, Russell J; Eckmann, David M

    2005-01-01

    .... Competitive protein adsorption plays a key role in the hemocompatibility of the surface. The synthesis of nonfouling surfaces is therefore one of the major prerequisites for devices for biomedical applications...

  5. D-Glucose as a modifying agent in gelatin/collagen matrix and reservoir nanoparticles for Calendula officinalis delivery.

    Science.gov (United States)

    Lam, P-L; Kok, S H-L; Bian, Z-X; Lam, K-H; Tang, J C-O; Lee, K K-H; Gambari, R; Chui, C-H

    2014-05-01

    Gelatin/Collagen-based matrix and reservoir nanoparticles require crosslinkers to stabilize the formed nanosuspensions, considering that physical instability is the main challenge of nanoparticulate systems. The use of crosslinkers improves the physical integrity of nanoformulations under the-host environment. Aldehyde-based fixatives, such as formaldehyde and glutaraldehyde, have been widely applied to the crosslinking process of polymeric nanoparticles. However, their potential toxicity towards human beings has been demonstrated in many previous studies. In order to tackle this problem, D-glucose was used during nanoparticle formation to stabilize the gelatin/collagen-based matrix wall and reservoir wall for the deliveries of Calendula officinalis powder and oil, respectively. In addition, therapeutic selectivity between malignant and normal cells could be observed. The C. officinalis powder loaded nanoparticles significantly strengthened the anti-cancer effect towards human breast adenocarcinoma MCF7 cells and human hepatoma SKHep1 cells when compared with the free powder. On the contrary, the nanoparticles did not show significant cytotoxicity towards normal esophageal epithelial NE3 cells and human skin keratinocyte HaCaT cells. On the basis of these evidences, D-glucose modified gelatin/collagen matrix nanoparticles containing C. officinalis powder might be proposed as a safer alternative vehicle for anti-cancer treatments. Copyright © 2014 Elsevier B.V. All rights reserved.

  6. Enhancement of Osteoblastic-Like Cell Activity by Glow Discharge Plasma Surface Modified Hydroxyapatite/β-Tricalcium Phosphate Bone Substitute

    Directory of Open Access Journals (Sweden)

    Eisner Salamanca

    2017-11-01

    Full Text Available Glow discharge plasma (GDP treatments of biomaterials, such as hydroxyapatite/β-tricalcium phosphate (HA/β-TCP composites, produce surfaces with fewer contaminants and may facilitate cell attachment and enhance bone regeneration. Thus, in this study we used argon glow discharge plasma (Ar-GDP treatments to modify HA/β-TCP particle surfaces and investigated the physical and chemical properties of the resulting particles (HA/β-TCP + Ar-GDP. The HA/β-TCP particles were treated with GDP for 15 min in argon gas at room temperature under the following conditions: power: 80 W; frequency: 13.56 MHz; pressure: 100 mTorr. Scanning electron microscope (SEM observations showed similar rough surfaces of HA/β-TCP + Ar-GDP HA/β-TCP particles, and energy dispersive spectrometry analyses showed that HA/β-TCP surfaces had more contaminants than HA/β-TCP + Ar-GDP surfaces. Ca/P mole ratios in HA/β-TCP and HA/β-TCP + Ar-GDP were 1.34 and 1.58, respectively. Both biomaterials presented maximal intensities of X-ray diffraction patterns at 27° with 600 a.u. At 25° and 40°, HA/β-TCP + Ar-GDP and HA/β-TCP particles had peaks of 200 a.u., which are similar to XRD intensities of human bone. In subsequent comparisons, MG-63 cell viability and differentiation into osteoblast-like cells were assessed on HA/β-TCP and HA/β-TCP + Ar-GDP surfaces, and Ar-GDP treatments led to improved cell growth and alkaline phosphatase activities. The present data indicate that GDP surface treatment modified HA/β-TCP surfaces by eliminating contaminants, and the resulting graft material enhanced bone regeneration.

  7. In-Vitro Comparative Study of In-office and Home Bleaching Agents on Surface Micro-morphology of Enamel

    International Nuclear Information System (INIS)

    Fatima, N.

    2016-01-01

    Objective: To evaluate the effect of home-use bleaching agent containing 16 percent Carbamide Peroxide (CP) and in-office bleaching agent with 38 percentage Hydrogen Peroxide (HP) on surface micro-morphology of enamel. Study Design: An experimental study. Place and Duration of Study: The discs were prepared at Material Engineering Department of NED University of Engineering and Technology, Karachi, and surface morphology was analyzed at Centralized Science Laboratory of Karachi University, Pakistan. Duration of study was one year from January to December 2012. Methodology: Forty five sound human third molar crowns, extracted for periodontal reason, were included in the study. Longitudinal sections were made using diamond disks (0.2 mm) under water lubrication to obtain enamel slabs measuring (3 mm x 3 mm). The slabs were embedded in polystyrene resin by using 2.0 cm diameter PVC molds, leaving the outer enamel surface uncovered by the resin. Ninety dental enamel slabs were prepared. The slabs were then randomly divided into 3 groups. Each group contained thirty specimens (n=30). Group 1 was kept in artificial saliva at 37 degree C in incubator (Memart, Germany) during whole experiment. Group 2 was treated with power whitening gel (White Smile 2011, Germany). Group 3 was treated with tooth whitening pen (White Smile 2011, Germany). The most central region or the region that was most representative of the entire surface area was used. The SEM (Jeol-Japan-JSM6380A, JAPAN) micrographs were examined to determine the type of surface presented. The enamel changes were classified as no or mild alteration, moderate alteration and severe altered surface. Results: Regarding micro-morphology, the enamel surface of control groups showed smooth surface in general with some scattered clear scratches due to the polishing procedure. The specimens bleached in group 2 and group 3, represented areas of mild erosion. Conclusion: Bleaching with 38 percentage Hydrogen Peroxide (HP) and

  8. The mid-IR spectral effects of darkening agents and porosity on the silicate surface features of airless bodies

    Science.gov (United States)

    Young, C. L.; Wray, J. J.; Poston, M.; Hand, K. P.; Carlson, R. W.

    2017-12-01

    The surfaces of airless bodies present opportunities to investigate the physical processes acting on planetary systems over time, without the need to account for surface-atmosphere interactions. Silicate surfaces mixed with fine-grained optically dark material with varying degrees of porosity are ubiquitous on many airless bodies (e.g., Earth's Moon, Deimos, Phobos, asteroids, meteorites, and moons of the outer solar system). Although the mid-IR is rich in emissivity features of important minerals and molecular groups, including organics [e.g., 1], it is less studied for airless conditions and presents challenges in signal-to-noise ratio, especially for the colder outer solar system bodies with fined-grained surfaces [2, 3]. We systematically measured the mid-IR spectra of different mixtures of three silicates (antigorite, lizardite, and pure silica) with varying porosities and amounts of darkening agent (iron oxide and carbon). Serpentines, such as antigorite and lizardite, are common to airless surfaces, and their mid-IR spectra in the presence of darkening agents and different surface porosities would be typical for those measured by spacecraft. Although pure silica has only been measured in the plumes of Enceladus, it presents exciting possibilities for other Saturn-system surfaces due to long range transport [4], and it is therefore important to investigate how its spectral signature would be manifested in the mid-IR. Overall, this work provides a library of mineral mixtures to facilitate dealing with current and future mid-IR datasets of airless bodies. These results are also applicable to the development of future missions to airless bodies, and our continuing efforts will help determine if mid-IR spectrometry is worthwhile for surface compositional studies of icy bodies. The mixtures presented here could be useful for testing future mid-IR instruments by confirming detectability of spectral features for typical materials on the surfaces of interest. [1

  9. The effect of home bleaching agents on the surface roughness of five different composite resins: A SEM evaluation.

    Science.gov (United States)

    Cengiz, Esra; Kurtulmus-Yilmaz, Sevcan; Ulusoy, Nuran; Deniz, Sule Tugba; Yuksel-Devrim, Ece

    2016-05-01

    The aim of this study was to investigate the effect of hydrogen peroxide (HP) and carbamide peroxide (CP) on the surface roughness of five different composite resins using profilometer and scanning electron microscope (SEM). Thirty-six specimens (1 mm thick, 10 mm in diameter) of five composite resins were fabricated. Each composite group was equally divided into three subgroups as control, CP and HP. In control group, specimens were stored in daily refreshed distilled water during the 14-day testing period. In other groups, 10% HP (Opalescence Treswhite) and 10% CP (Opalescence PF) were applied and surface roughness values (Ra) of each specimen were measured with a profilometer at the end of 14 days. Additionally, SEM analysis was performed to evaluate the surface deformations of composite resins. Data were analyzed with Kruskal-Wallis and Mann-Whitney U tests. Ra values of composite groups exposed to bleaching agents were statistically higher than control group (p composite group while SEM micrographs showed higher surface alterations at HP group compared to CP. Among the composite resins tested, Ceram-X Mono revealed the lowest Ra values after CP and HP applications as seen at SEM images. Home bleaching agents increased the surface roughness of all composites. Except CP applied Ceram-X mono specimens, Ra values of all composite resins evaluated in this study exceeded the critical limit of 0.2 μm. Ceram-X mono was the least affected composite material after bleaching application. SCANNING 38:277-283, 2016. © 2016 Wiley Periodicals, Inc. © Wiley Periodicals, Inc.

  10. Topographic assessment of human enamel surface treated with different topical sodium fluoride agents: Scanning electron microscope consideration

    Directory of Open Access Journals (Sweden)

    Gurlal Singh Brar

    2017-01-01

    Full Text Available Introduction: Continuous balanced demineralization and remineralization are natural dynamic processes in enamel. If the balance is interrupted and demineralization process dominates, it may eventually lead to the development of carious lesions in enamel and dentine. Fluoride helps control decay by enhancing remineralization and altering the structure of the tooth, making the surface less soluble. Methodology: One hundred and twenty sound human permanent incisors randomly and equally distributed into six groups as follows: Group I - Control, II - Sodium fluoride solution, III - Sodium fluoride gel, IV - Sodium fluoride varnish, V - Clinpro Tooth Crème (3M ESPE, and VI-GC Tooth Mousse Plus or MI Paste Plus. The samples were kept in artificial saliva for 12 months, and the topical fluoride agents were applied to the respective sample groups as per the manufacturer instructions. Scanning electron microscope (SEM evaluation of all the samples after 6 and 12 months was made. Results: Morphological changes on the enamel surface after application of fluoride in SEM revealed the presence of globular precipitate in all treated samples. Amorphous, globular, and crystalline structures were seen on the enamel surface of the treated samples. Clear differences were observed between the treated and untreated samples. Conclusion: Globular structures consisting of amorphous CaF2precipitates, which acted as a fluoride reservoir, were observed on the enamel surface after action of different sodium fluoride agents. CPP-ACPF (Tooth Mousse and Tricalcium phosphate with fluoride (Clinpro tooth crème are excellent delivery vehicles available in a slow release amorphous form to localize fluoride at the tooth surface.

  11. The effect of disinfectant agents on dimensional stability and surface roughness of a tissue conditioner material

    Directory of Open Access Journals (Sweden)

    Amiralireza Khaledi

    2011-01-01

    Conclusion: The results showed that the disinfectant solutions used in this study did not have a significant effect on the surface quality and dimensional accuracy of Visco-gel as a functional impression material.

  12. The surface pH of glass ionomer cavity lining agents.

    Science.gov (United States)

    Woolford, M J

    1989-12-01

    It is considered that acid release from the surface of glass ionomer (polyalkenoate) cements may be associated with early pulpal sensitivity following the use of these materials. This study was carried out to examine the surface pH of different types of glass ionomer lining cements using a flat-ended pH electrode. It was found that the surface pH remains low for this group of materials during the first hour of setting. Different types of glass ionomer lining cement were also shown to behave differently when considering acid release from the surface. Conclusions regarding the behaviour of glass ionomers should only be made with reference to the specific material tested.

  13. Mercapto-based coupling agent for improved thermophotovoltaic device back surface reflector adhesion and reflectance

    Energy Technology Data Exchange (ETDEWEB)

    Wernsman, Bernard; Fiedor, Joseph N.; Irr, Lawrence G.; Palmisiano, Marc N.

    2016-10-04

    A back surface reflector (BSR) is described. The BSR includes a reflecting layer, a substrate and an adhesion layer between the reflecting layer and the substrate. The adhesion layer includes 3-mercaptopropyl (trimethoxy) silane (a.k.a. Merc).

  14. Bactericidal effects of plasma-modified surface chemistry of silicon nanograss

    Science.gov (United States)

    Ostrikov, Kola; Macgregor-Ramiasa, Melanie; Cavallaro, Alex; (Ken Ostrikov, Kostya; Vasilev, Krasimir

    2016-08-01

    The surface chemistry and topography of biomaterials regulate the adhesion and growth of microorganisms in ways that are still poorly understood. Silicon nanograss structures prepared via inductively coupled plasma etching were coated with plasma deposited nanometer-thin polymeric films to produce substrates with controlled topography and defined surface chemistry. The influence of surface properties on Staphylococcus aureus proliferation is demonstrated and explained in terms of nanograss substrate wetting behaviour. With the combination of the nanograss topography; hydrophilic plasma polymer coatings enhanced antimicrobial activity while hydrophobic coatings reduced it. This study advances the understanding of the effects of surface wettability on the bactericidal properties of reactive nano-engineered surfaces.

  15. Bactericidal effects of plasma-modified surface chemistry of silicon nanograss

    International Nuclear Information System (INIS)

    Ostrikov, Kola; Macgregor-Ramiasa, Melanie; Cavallaro, Alex; Ostrikov, Kostya; Vasilev, Krasimir

    2016-01-01

    The surface chemistry and topography of biomaterials regulate the adhesion and growth of microorganisms in ways that are still poorly understood. Silicon nanograss structures prepared via inductively coupled plasma etching were coated with plasma deposited nanometer-thin polymeric films to produce substrates with controlled topography and defined surface chemistry. The influence of surface properties on Staphylococcus aureus proliferation is demonstrated and explained in terms of nanograss substrate wetting behaviour. With the combination of the nanograss topography; hydrophilic plasma polymer coatings enhanced antimicrobial activity while hydrophobic coatings reduced it. This study advances the understanding of the effects of surface wettability on the bactericidal properties of reactive nano-engineered surfaces. (paper)

  16. Effect of Collagen Matrix Saturation on the Surface Free Energy of Dentin using Different Agents.

    Science.gov (United States)

    de Almeida, Leopoldina de Fátima Dantas; Souza, Samilly Evangelista; Sampaio, Aline Araújo; Cavalcanti, Yuri Wanderley; da Silva, Wander José; Del Bel Cur, Altair A; Hebling, Josimeri

    2015-07-01

    The surface free energy of conditioned-dentin is one of the factors that interfere with monomeric infiltration of the interfibrillar spaces. Saturation of the tooth matrix with different substances may modulate this energy and, consequently, the wettability of the dentin. To evaluate the influence of different substances used to saturate conditioned-dentin on surface free energy (SFE) of this substrate. Dentin blocks (4 × 7 × 1 mm, n = 6/ group), obtained from the roots of bovine incisors, were etched using phosphoric acid for 15 seconds, rinsed and gently dried. The surfaces were treated for 60 seconds with: ultra-purified water (H20-control); ethanol (EtOH), acetone (ACT), chlorhexidine (CHX), ethylenediaminetetraacetic acid (EDTA); or sodium hypochlorite (NaOCl). The tooth surfaces were once again dried with absorbent paper and prepared for SFE evaluation using three standards: water, formamide and bromonaphthalene. Analysis of variance (ANOVA) and Dunnet's tests (a = 0.05) were applied to the data. Ethylenediaminetetraacetic acid was the only substance that caused a change to the contact angle for the standards water and formamide, while only EtOH influenced the angles formed between formamide and the dentin surface. None of the substances exerted a significant effect for bromonaphtha-lene. In comparison to the control, only EDTA and NaOCl altered both polar components of the SFE. Total SFE was increased by saturation of the collagen matrix by EDTA and reduced when NaOCl was used. Saturation of the collagen matrix by EDTA and EtOH changed the surface free energy of the dentin. In addition, the use of NaOCl negatively interfered with the properties evaluated. The increase of surface free energy and wettability of the dentin surface would allow higher penetration of the the adhesive system, which would be of importance to the clinical success of resin-dentin union.

  17. Surface-modified CdSe quantum dots for the sensitive and selective determination of Cu(II) in aqueous solutions by luminescent measurements

    International Nuclear Information System (INIS)

    Fernandez-Argueelles, Maria Teresa; Jin, Wei Jun; Costa-Fernandez, Jose M.; Pereiro, Rosario; Sanz-Medel, Alfredo

    2005-01-01

    The use of water-soluble luminescent CdSe quantum dots (QDs), whose surface was modified either with 2-mercaptoethane sulphonic acid or with 2-mercaptoacetic acid, was investigated for the sensitive and selective determination of copper(II) ions in aqueous solutions. A pH 5.5 was selected for measurement. Also, the effect of the presence of different surfactant agents in the sample solution, in order to stabilize the fluorescent signals of the QDs in water, has been investigated. A 10 -3 M of dodecyltrimethylammonium chloride final concentration was selected. Fluorescence signals were found to be stable for at least several days in such conditions. Higher sensitivity was obtained for the sulphonic-modified CdSe QDs. Detection limits for Cu(II) of 0.2 μg l -1 , a dynamic range up to 30 μg l -1 , and a R.S.D. of ±2.8% for 10 replicates of a 2.5 μg l -1 Cu(II) solution were obtained as analytical performance characteristics. Besides, the influence on the fluorescence signal of foreign cations, including Na + , K + , Ca 2+ , Mg 2+ , Zn 2+ , Mn 2+ , Co 3+ , Ag + , Hg 2+ and Fe 3+ was studied (to avoid inner filter effect, the colourless complex FeF 6 3- was investigated instead of Fe 3+ ). Results showed a high selectivity of the sulphonic-modified QDs towards Cu(II) ions. The proposed method demonstrated improved sensitivity and selectivity characteristics for Cu(II) determinations as compared to other already described luminescence QDs-based analytical methods for metal ions determinations. Analytical applicability of the QDs has been demonstrated by tap and fountain water analysis. Results of Cu(II) determinations were in good agreement to those obtained by using an alternative analytical method

  18. In vitro osteoinduction of human mesenchymal stem cells in biomimetic surface modified titanium alloy implants.

    Science.gov (United States)

    Santander, Sonia; Alcaine, Clara; Lyahyai, Jaber; Pérez, Maria Angeles; Rodellar, Clementina; Doblaré, Manuel; Ochoa, Ignacio

    2014-01-01

    Interaction between cells and implant surface is crucial for clinical success. This interaction and the associated surface treatment are essential for achieving a fast osseointegration process. Several studies of different topographical or chemical surface modifications have been proposed previously in literature. The Biomimetic Advanced Surface (BAS) topography is a combination of a shot blasting and anodizing procedure. Macroroughness, microporosity of titanium oxide and Calcium/Phosphate ion deposition is obtained. Human mesenchymal stem cells (hMCSs) response in vitro to this treatment has been evaluated. The results obtained show an improved adhesion capacity and a higher proliferation rate when hMSCs are cultured on treated surfaces. This biomimetic modification of the titanium surface induces the expression of osteblastic differentiation markers (RUNX2 and Osteopontin) in the absence of any externally provided differentiation factor. As a main conclusion, our biomimetic surface modification could lead to a substantial improvement in osteoinduction in titanium alloy implants.

  19. Surface free energy of ultra-high molecular weight polyethylene modified by electron and gamma irradiation

    International Nuclear Information System (INIS)

    Abdul-Kader, A.M.; Turos, A.; Radwan, R.M.; Kelany, A.M.

    2009-01-01

    Surface free energy of biocompatible polymers is important factor which affects the surface properties such as wetting, adhesion and biocompatibility. In the present work, the change in the surface free energy of ultra-high molecular weight polyethylene (UHMWPE) samples, which is produced by electron beam and gamma ray irradiation were, investigated. Mechanism of the changes in surface free energy induced by irradiations of doses ranging from 25 to 500 kGy was studied. FTIR technique was applied for sample analysis. Contact angle measurements showed that wettability and surface free energy of samples have increased with increasing the irradiation dose, where the values of droplet contact angle of the samples decrease gradually with increasing the radiation dose. The increase in the wettability and surface free energy of the irradiated samples are attributed to formation of hydrophilic groups on the polymer surface by the oxidation, which apparently occurs by exposure of irradiated samples to the air.

  20. Synthesis and quantitative structure-activity relationship (QSAR) study of novel 4-acyloxypodophyllotoxin derivatives modified in the A and C rings as insecticidal agents.

    Science.gov (United States)

    He, Shuzhen; Shao, Yonghua; Fan, Lingling; Che, Zhiping; Xu, Hui; Zhi, Xiaoyan; Wang, Juanjuan; Yao, Xiaojun; Qu, Huan

    2013-01-23

    In continuation of our program aimed at the discovery and development of natural-product-based insecticidal agents, we have synthesized three series of novel 4-acyloxy compounds derived from podophyllotoxin modified in the A and C rings, which is isolated as the main secondary metabolite from the roots and rhizomes of Podophyllum hexandrum . Their insecticidal activity was preliminarily evaluated against the pre-third-instar larvae of Mythimna separata in vivo. Compound 9g displayed the best promising insecticidal activity. It revealed that cleavage of the 6,7-methylenedioxy group of podophyllotoxin will lead to a less active compound and that the C-4 position of podophyllotoxin was the important modification location. A quantitative structure-activity relationship (QSAR) model was developed by genetic algorithm combined with multiple linear regression (GA-MLR). For this model, the squared correlation coefficient (R(2)) is 0.914, the leave-one-out cross-validation correlation coefficient (Q(2)(LOO)) is 0.881, and the root-mean-square error (RMSE) is 0.024. Five descriptors, BEHm2, Mor14v, Wap, G1v, and RDF020e, are likely to influence the biological activity of these compounds. Among them, two important ones are BEHm2 and Mor14v. This study will pave the way for further design, structural modification, and development of podophyllotoxin derivatives as insecticidal agents.

  1. Surface-Modified Membrane as A Separator for Lithium-Ion Polymer Battery

    Directory of Open Access Journals (Sweden)

    Jun Young Kim

    2010-04-01

    Full Text Available This paper describes the fabrication of novel modified polyethylene (PE membranes using plasma technology to create high-performance and cost-effective separator membranes for practical applications in lithium-ion polymer batteries. The modified PE membrane via plasma modification process plays a critical role in improving wettability and electrolyte retention, interfacial adhesion between separators and electrodes, and cycle performance of lithium-ion polymer batteries. This paper suggests that the performance of lithium-ion polymer batteries can be greatly enhanced by the plasma modification of commercial separators with proper functional materials for targeted application.

  2. Biological Evaluation of Double Point Modified Analogues of 1,25-Dihydroxyvitamin D2 as Potential Anti-Leukemic Agents

    Science.gov (United States)

    Corcoran, Aoife; Nadkarni, Sharmin; Yasuda, Kaori; Sakaki, Toshiyuki; Brown, Geoffrey; Kutner, Andrzej; Marcinkowska, Ewa

    2016-01-01

    Structurally similar double-point modified analogues of 1,25-dihydroxyvitamin D2 (1,25D2) were screened in vitro for their pro-differentiating activity against the promyeloid cell line HL60. Their affinities towards human full length vitamin D receptor (VDR) and metabolic stability against human vitamin D 24-hydroxylase (CYP24A1) were also tested. The analogues (PRI-1730, PRI-1731, PRI-1732, PRI-1733 and PRI-1734) contained 5,6-trans modification of the A-ring and of the triene system, additional hydroxyl or unsaturation at C-22 in the side chain and reversed absolute configuration (24-epi) at C-24 of 1,25D2. As presented in this paper, introduction of selected structural modifications simultaneously in two distinct parts of the vitamin D molecule resulted in a divergent group of analogues. Analogues showed lower VDR affinity in comparison to that of the parent hormones, 1,25D2 and 1,25D3, and they caused effective HL60 cell differentiation only at high concentrations of 100 nM and above. Unexpectedly, introducing of a 5,6-trans modification combined with C-22 hydroxyl and 24-epi configuration switched off entirely the cell differentiation activity of the analogue (PRI-1734). However, this analogue remained a moderate substrate for CYP24A1, as it was metabolized at 22%, compared to 35% for 1,25D2. Other analogues from this series were either less (12% for PRI-1731 and PRI-1733) or more (52% for PRI-1732) resistant to the enzymatic deactivation. Although the inactive analogue PRI-1734 failed to show VDR antagonism, when tested in HL60 cells, its structure might be a good starting point for our design of a vitamin D antagonist. PMID:26840307

  3. Biological Evaluation of Double Point Modified Analogues of 1,25-Dihydroxyvitamin D2 as Potential Anti-Leukemic Agents

    Directory of Open Access Journals (Sweden)

    Aoife Corcoran

    2016-02-01

    Full Text Available Structurally similar double-point modified analogues of 1,25-dihydroxyvitamin D2 (1,25D2 were screened in vitro for their pro-differentiating activity against the promyeloid cell line HL60. Their affinities towards human full length vitamin D receptor (VDR and metabolic stability against human vitamin D 24-hydroxylase (CYP24A1 were also tested. The analogues (PRI-1730, PRI-1731, PRI-1732, PRI-1733 and PRI-1734 contained 5,6-trans modification of the A-ring and of the triene system, additional hydroxyl or unsaturation at C-22 in the side chain and reversed absolute configuration (24-epi at C-24 of 1,25D2. As presented in this paper, introduction of selected structural modifications simultaneously in two distinct parts of the vitamin D molecule resulted in a divergent group of analogues. Analogues showed lower VDR affinity in comparison to that of the parent hormones, 1,25D2 and 1,25D3, and they caused effective HL60 cell differentiation only at high concentrations of 100 nM and above. Unexpectedly, introducing of a 5,6-trans modification combined with C-22 hydroxyl and 24-epi configuration switched off entirely the cell differentiation activity of the analogue (PRI-1734. However, this analogue remained a moderate substrate for CYP24A1, as it was metabolized at 22%, compared to 35% for 1,25D2. Other analogues from this series were either less (12% for PRI-1731 and PRI-1733 or more (52% for PRI-1732 resistant to the enzymatic deactivation. Although the inactive analogue PRI-1734 failed to show VDR antagonism, when tested in HL60 cells, its structure might be a good starting point for our design of a vitamin D antagonist.

  4. A tannin-blocking agent does not modify the preference of sheep towards tannin-containing plants.

    Science.gov (United States)

    Hernández-Orduño, G; Torres-Acosta, J F J; Sandoval-Castro, C A; Capetillo-Leal, C M; Aguilar-Caballero, A J; Alonso-Díaz, M A

    2015-06-01

    Sheep have been suggested to use their senses to perceive plant properties and associate their intake with consequences after ingestion. However, sheep with browsing experience do not seem to select against tannin-rich browsing materials in cafeteria trials. Thus, the objective of the present study was to evaluate the relationship between the chemical composition, selectivity index (SI), preference and intake rate (IR) of tannin-containing forage trees offered to sheep in cafeteria experiments. Four trees were selected for their condensed tannin content and their varying biological activities. Havardia albicans (high biological activity), Leucaena leucocephala (medium biological activity), Acacia gaumeri (low biological activity) and Brosimum alicastrum (very low biological activity) were used in this study. Ten hair sheep (23.7kg±1.43LW) with eight months of browsing experience in native vegetation were used in this study. Polyethylene glycol (PEG 3600MW) was administered to five sheep during all experiments. In experiment 1, fresh foliage from all trees was offered ad libitum for 4h. In experiment 2, B. alicastrum was withdrawn and the preference was determined again. The forage preference in experiment 1 was A. gaumeri (14.77gDM/kgLW)>B. alicastrum (11.77gDM/kgLW)>H. albicans (3.71gDM/kgLW)=L. leucocephala (1.87gDM/kgLW) (PH. albicans=L. leucocephala. PEG administration had no effect on the preference or IR. The intake rate seemed to have been affected by the plant density. Moreover, fiber compounds were found to be better predictors of DM intake than polyphenolic compounds at levels typically found in the evaluated forages. It was concluded that tannins and PEG did not modify the preferences of sheep in cafeteria trials. Thus, tannins are not involved in the preference regulation of animals with browsing experience. Copyright © 2015 Elsevier Inc. All rights reserved.

  5. Study on Synthesis of Thoreau-modified 3, 5-Dimethyl-Thioltoluenediamine Used as Epoxy Resin Curing Agent and Its Performance

    Science.gov (United States)

    Peng, Yongli; Xiao, Wenzheng

    2017-06-01

    A novel curing agent Thoreau modified 3, 5-Dimethyl-thioltoluenediamine was synthesized and its molecular structure was characterized by FTIR and DSC. The curing kinetics of a high toughness and low volume shrinkage ratio epoxy system (modified DMTDA/DGEBA) was studied by differential scanning calorimetry (DSC) under noni so thermal conditions. The data were fitted to an order model and autocatalytic model respectively. The results indicate that in order model deviates significantly from experimental data. Malik’s method was used to prove that the curing kinetics of the system concerned follow single-step autocatalytic model, and a “single-point model-free” approach was employed to calculate meaningful kinetic parameters. The DSC curves derived from autocatalytic model gave satisfactory agreement with that of experiment in the range 5K/min∼25K/min. As the heating rate increased, the predicted DSC curves deviated from experimental curves, and the total exothermic enthalpy declined owing to the transition of competition relationship between kinetics control and diffusion control.

  6. Characterization of dentin surface after application of desensitizing agents: SEM analysis

    Directory of Open Access Journals (Sweden)

    Sandra Kiss Moura

    2016-04-01

    Full Text Available Objective: To analyze the morphology of dentin after application of desensitizing agents. Materials and Methods: Ten third molars were sectioned to obtain 2mm thick dentin disks and divided into 4 groups (n = 5: G0 – cut with a diamond disk, G1 – Colgate® Sensitive Pro-relief™ toothpaste; G2 – Du­raflur® Fluoride varnish; G3 – biosilicate aqueous solution (Biosilicato®. After storage in dehydrated silica-gel (37°C/24h, the samples were placed on aluminum supports, coated with gold-palladium and observed under a scanning electron microscope. Post-treatment photomicrographs were obtained of the dentin. Results: In the G1 group the smear layer was observed; in the G2 and G4 groups, both the desensitizing agents and the smear layer and in the G3 group, a film of varnish. Conclusions: Different morphologies of dentin were observed after the proposed treatments for dentin hypersensitivity.

  7. Application of phosphating techniques to aluminium and carbon steel surfaces using nitro guanidine as oxidizing agent

    International Nuclear Information System (INIS)

    Briseno M, S.A.

    1995-01-01

    Phosphate coatings are inorganic crystalline deposits laid down uniformly on properly prepared surfaces by a chemical reaction with the treated base metal. The reaction consists in dissolving some surface metal by acid attack and then causing surface neutralization of the phosphate solution with consequent precipitation of the phosphate coating. Phosphate coatings do not provide appreciable corrosion protection in themselves. They are useful mainly as a base for paints, ensuring good adherence of paint to steel and decreasing the tendency for corrosion to under cut the paint film at scratches or other defects. In this work firstly were realized phosphate on standard carbon steel, employing technical of cold phosphate (at 40 Centigrade degrees and with a treatment time of 30 minutes) and hot phosphate (at 88 Centigrade degrees and with a treatment time of 15 minutes), where with this last were obtained the best results. Both methods used phosphate solutions of Zn/Mn and using as catalyst Nitro guanidine. Aluminium surfaces were phosphate used solutions of Cr and as catalyst Sodium bi fluoride. The phosphating on this surface were realized at temperature of 50 Centigrade degrees and with a treatment time of 10 minutes. In this work were obtained a new phosphate coatings on steel surfaces, these coatings were realized with a phosphate solution manufactured with the precipitates gathered during the hot phosphating on carbon steel. These coatings show excellent physical characteristics and of corrosion resistance. Were determined the physical testings of the coatings phosphate obtained on carbon steel and aluminium surfaces. These testing were: roughness, thickness, microhardness and adhesion. The best results were showed in carbon steel phosphate with precipitated solutions. The technical of analysis for activation with thermic neutrons was used to determine the phosphate coatings composition. Finally, corrosion testings were realized by means of two methods

  8. Ascorbic acid surface modified TiO₂-thin layers as a fully integrated analysis system for visual simultaneous detection of organophosphorus pesticides.

    Science.gov (United States)

    Li, Shunxing; Liang, Wenjie; Zheng, Fengying; Lin, Xiaofeng; Cai, Jiabai

    2014-11-06

    TiO₂ photocatalysis and colorimetric detection are coupled with thin layer chromatography (TLC) for the first time to develop a fully integrated analysis system. Titania@polystyrene hybrid microspheres were surface modified with ascorbic acid, denoted AA-TiO₂@PS, and used as the stationary phase for TLC. Because the affinity between AA-TiO₂@PS and organophosphorus pesticides (OPs) was different for different species of OPs (including chlopyrifos, malathion, parathion, parathion-methyl, and methamidophos), OPs could be separated simultaneously by the mobile phase in 12.0 min with different Rf values. After surface modification, the UV-vis wavelength response range of AA-TiO₂@PS was expanded to 650 nm. Under visible-light irradiation, all of the OPs could be photodegraded to PO₄(3-) in 25.0 min. Based on the chromogenic reaction between PO₄(3-) and chromogenic agents (ammonium molybdate and ascorbic acid), OPs were quantified from color intensity images using a scanner in conjunction with image processing software. So, AA-TiO₂@PS was respectively used as the stationary phase of TLC for efficient separation of OPs, as a photocatalyst for species transformation of phosphorus, and as a colorimetric probe for on-field simultaneous visual detection of OPs in natural water. Linear calibration curves for each OP ranged from 19.3 nmol P L(-1) to 2.30 μmol P L(-1). This integrated analysis system was simple, inexpensive, easy to operate, and sensitive.

  9. Toxicology Studies on Lewisite and Sulfur Mustard Agents: Modified Dominant Lethal Study of Sulfur Mustard in Rats Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Sasser, L. B.; Cushing, J. A.; Kalkwarf, D. R.; Buschbom, R. L.

    1989-05-01

    Occupational health standards have not been established for sulfur mustard (HD) [bis{2-chloroethyl)-sulfide) ' a strong alkylating agent with known mutagenic properties. Little, however, is known about the mutagenic activity of HD in mammalian species and data regarding the dominant lethal effects of HD are ambiguous. The purpose of this study was to determine the dominant lethal effect in male and female rats orally exposed to HD. The study was conducted in two phases; a female dominant lethal phase and a male dominant lethal phase. Sprague-Dawley rats of each sex were administered 0.08, 0.20, or 0.50 mg/kg HD in sesame oil 5 days/week for 10 weeks. For the female phase, treated or untreated males were mated with treated females and their fetuses were evaluated at approximately 14 days after copulation. For the male dominant lethal phase, treated males cohabited with untreated femal (during 5 days of each week for 10 weeks) and females were sacrificed for fetal evaluation 14 days after the midweek of cohabitation during each of the 10 weeks. The appearance and behavior of the rats were unremarkable throughout the experiment and there were no treatment-related deaths. Growth rates were reduced in both female and male rats treated with 0.50 mg/kg HD. Indicators of reproductive performance did not demonstrate significant female dominant lethal effects, although significant male dominant lethal effects were observed at 2 and 3 week post-exposure. These effects included increases of early fetal resorptions and preimplantation losses and decreases of total live embryo implants. These effects were most consistently observed at a dose of 0.50 mg/kg, but frequently occurred at the lower doses. Although no treatment-related effects on male reproductive organ weights or sperm motility were found, a significant increase in the percentage of abnormal sperm was detected in males exposed to 0. 50 mg/kg HD. The timing of these effects is consistent with an effect during the

  10. Evaluation of glycodendron and synthetically modified dextran clearing agents for multistep targeting of radioisotopes for molecular imaging and radioimmunotherapy.

    Science.gov (United States)

    Cheal, Sarah M; Yoo, Barney; Boughdad, Sarah; Punzalan, Blesida; Yang, Guangbin; Dilhas, Anna; Torchon, Geralda; Pu, Jun; Axworthy, Don B; Zanzonico, Pat; Ouerfelli, Ouathek; Larson, Steven M

    2014-02-03

    A series of N-acetylgalactosamine-dendrons (NAG-dendrons) and dextrans bearing biotin moieties were compared for their ability to complex with and sequester circulating bispecific antitumor antibody streptavidin fusion protein (scFv4-SA) in vivo, to improve tumor-to-normal tissue concentration ratios for multistep targeted (MST) radioimmunotherapy and diagnosis. Specifically, a total of five NAG-dendrons employing a common synthetic scaffold structure containing 4, 8, 16, or 32 carbohydrate residues and a single biotin moiety were prepared (NAGB), and for comparative purposes, a biotinylated-dextran with an average molecular weight of 500 kD was synthesized from amino-dextran (DEXB). One of the NAGB compounds, CA16, has been investigated in humans; our aim was to determine if other NAGB analogues (e.g., CA8 or CA4) were bioequivalent to CA16 and/or better suited as MST reagents. In vivo studies included dynamic positron-emission tomography (PET) imaging of (124)I-labeled-scFv4-SA clearance and dual-label biodistr