WorldWideScience

Sample records for surface magnetometer employs

  1. Estimating Antarctic near-surface magnetic anomalies from Oersted and CHAMP satellite magnetometer observations

    Science.gov (United States)

    von Frese, R. R.; Kim, H.; Gaya-Pique, L. R.; Taylor, P. T.; Golynsky, A. V.; Kim, J.

    2004-12-01

    Significant improvement in predicting near-surface magnetic anomalies can result from the highly accurate magnetic observations of the CHAMP satellite that is orbiting at about 400 km altitude. In general, regional magnetic signals of the crust are strongly masked by the core field and its secular variations due to wavelength coupling in the spherical harmonic representation and thus are difficult to isolate in the satellite measurements. However, efforts to isolate the regional lithospheric from core field components can exploit the correlations between the CHAMP magnetic anomalies and the pseudo magnetic effects inferred from gravity-derived crustal thickness variations. In addition, we can use spectral correlation theory to filter the static lithospheric field components from the dynamic external field effects. Employing these procedures, we processed the CHAMP magnetic observations for an improved magnetic anomaly map of the Antarctic crust. Relative to the much higher altitude Oersted and noisier Magsat observations, CHAMP magnetic anomalies at 400 km altitude reveal new details on the effects of intra-crustal magnetic features and crustal thickness variations of the Antarctic. Moreover, these results greatly facilitate predicting magnetic anomalies in the regional coverage gaps of the ADMAP compilation of Antarctic magnetic anomalies from shipborne, airborne and ground surveys. Our analysis suggests that considerable new insights on the magnetic properties of the lithosphere may be revealed by a further order-of-magnitude improvement in the accuracy of the magnetometer measurements at minimum orbital altitude.

  2. Fluxgate vector magnetometers: Compensated multi-sensor devices for ground, UAV and airborne magnetic survey for various application in near surface geophysics

    Science.gov (United States)

    Gavazzi, Bruno; Le Maire, Pauline; Munschy, Marc; Dechamp, Aline

    2017-04-01

    Fluxgate 3-components magnetometer is the kind of magnetometer which offers the lightest weight and lowest power consumption for the measurement of the intensity of the magnetic field. Moreover, vector measurements make it the only kind of magnetometer allowing compensation of magnetic perturbations due to the equipment carried with it. Unfortunately, Fluxgate magnetometers are quite uncommon in near surface geophysics due to the difficulty to calibrate them precisely. The recent advances in calibration of the sensors and magnetic compensation of the devices from a simple process on the field led Institut de Physique du Globe de Strasbourg to develop instruments for georeferenced magnetic measurements at different scales - from submetric measurements on the ground to aircraft-conducted acquisition through the wide range offered by unmanned aerial vehicles (UAVs) - with a precision in the order of 1 nT. Such equipment is used for different kind of application: structural geology, pipes and UXO detection, archaeology.

  3. Atomic magnetometer

    Science.gov (United States)

    Schwindt, Peter [Albuquerque, NM; Johnson, Cort N [Albuquerque, NM

    2012-07-03

    An atomic magnetometer is disclosed which uses a pump light beam at a D1 or D2 transition of an alkali metal vapor to magnetically polarize the vapor in a heated cell, and a probe light beam at a different D2 or D1 transition to sense the magnetic field via a polarization rotation of the probe light beam. The pump and probe light beams are both directed along substantially the same optical path through an optical waveplate and through the heated cell to an optical filter which blocks the pump light beam while transmitting the probe light beam to one or more photodetectors which generate electrical signals to sense the magnetic field. The optical waveplate functions as a quarter waveplate to circularly polarize the pump light beam, and as a half waveplate to maintain the probe light beam linearly polarized.

  4. Surface-enhanced Raman scattering from magneto-metal nanoparticle assemblies.

    Science.gov (United States)

    Qu, Hua; Lai, Yuming; Niu, Dongzi; Sun, Shuqing

    2013-02-06

    Binary nanoparticles composed of a superparamagnetic Fe(3)O(4) core and an Au nanoshell (Fe(3)O(4)@Au) were prepared via a simple co-precipitation method followed by seed-mediated growth process. The nanoparticles exhibited functions of both fast magnetic response and local surface plasmon resonance. The Fe(3)O(4)@Au nanoparticles were used as probes for surface-enhanced Raman scattering (SERS) using p-thiocresol (p-TC) as reporter molecule. With the ability of analyte capture and concentration magnetically, the Fe(3)O(4)@Au nanoparticles showed significant SERS properties with excellent reproducibility. Under non-optimized conditions, detection limit as low as 4.55 pM of analyte can be reached using Fe(3)O(4)@Au nanoparticle assemblies, which excel remarkably the cases with traditional Au nanoprobes. Copyright © 2012 Elsevier B.V. All rights reserved.

  5. MOURA magnetometer for Mars MetNet Precursor Mission. Its potential for an in situ magnetic environment and surface characterization

    Energy Technology Data Exchange (ETDEWEB)

    Diaz Michelena, M.; Sanz, R.; Fernandez, A.B.; Manuel, V. de; Cerdan, M.F.; Apestigue, V.; Arruego, I.; Azcue, J.; Dominguez, J.A.; Gonzalez, M.; Guerrero, H.; Sabau, M.; Kilian, R.; Baeza, O.; Ros, F.; Vazquez, M.; Tordesillas, J.M.; Covisa, P.; Aguado, J.

    2016-07-01

    MOURA magnetometer and gradiometer is part of the scientific instrumentation for Mars MetNet Precursor mission. This work describes the objective of the investigation, summarizes the work done in the design and development of the sensor as well as its calibration, and shows the demonstration campaigns to show the potential of such instrument for planetary landers and rovers. (Author)

  6. Tuned optical cavity magnetometer

    Science.gov (United States)

    Okandan, Murat; Schwindt, Peter

    2010-11-02

    An atomic magnetometer is disclosed which utilizes an optical cavity formed from a grating and a mirror, with a vapor cell containing an alkali metal vapor located inside the optical cavity. Lasers are used to magnetically polarize the alkali metal vapor and to probe the vapor and generate a diffracted laser beam which can be used to sense a magnetic field. Electrostatic actuators can be used in the magnetometer for positioning of the mirror, or for modulation thereof. Another optical cavity can also be formed from the mirror and a second grating for sensing, adjusting, or stabilizing the position of the mirror.

  7. GOES Space Environment Monitor, Magnetometer

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Three orthogonal flux-gate magnetometer elements, (spinning twin fluxgate magnetometer prior to GOES-8) provide magnetic field measurements in three mutually...

  8. Choice of Magnetometers and Gradiometers after Signal Space Separation.

    Science.gov (United States)

    Garcés, Pilar; López-Sanz, David; Maestú, Fernando; Pereda, Ernesto

    2017-12-16

    Modern Elekta Neuromag MEG devices include 102 sensor triplets containing one magnetometer and two planar gradiometers. The first processing step is often a signal space separation (SSS), which provides a powerful noise reduction. A question commonly raised by researchers and reviewers relates to which data should be employed in analyses: (1) magnetometers only, (2) gradiometers only, (3) magnetometers and gradiometers together. The MEG community is currently divided with regard to the proper answer. First, we provide theoretical evidence that both gradiometers and magnetometers result from the backprojection of the same SSS components. Then, we compare resting state and task-related sensor and source estimations from magnetometers and gradiometers in real MEG recordings before and after SSS. SSS introduced a strong increase in the similarity between source time series derived from magnetometers and gradiometers (r² = 0.3-0.8 before SSS and r² > 0.80 after SSS). After SSS, resting state power spectrum and functional connectivity, as well as visual evoked responses, derived from both magnetometers and gradiometers were highly similar (Intraclass Correlation Coefficient > 0.8, r² > 0.8). After SSS, magnetometer and gradiometer data are estimated from a single set of SSS components (usually ≤ 80). Equivalent results can be obtained with both sensor types in typical MEG experiments.

  9. Optical atomic magnetometer

    Science.gov (United States)

    Budker, Dmitry; Higbie, James; Corsini, Eric P

    2013-11-19

    An optical atomic magnetometers is provided operating on the principles of nonlinear magneto-optical rotation. An atomic vapor is optically pumped using linearly polarized modulated light. The vapor is then probed using a non-modulated linearly polarized light beam. The resulting modulation in polarization angle of the probe light is detected and used in a feedback loop to induce self-oscillation at the resonant frequency.

  10. THOR Fluxgate Magnetometer (MAG)

    Science.gov (United States)

    Nakamura, Rumi; Eastwood, Jonathan; Magnes, Werner; Carr, Christopher, M.; O'Brien, Helen, L.; Narita, Yasuhito; K, Chen, Christopher H.; Berghofer, Gerhard; Valavanoglou, Aris; Delva, Magda; Plaschke, Ferdinand; Cupido, Emanuele; Soucek, Jan

    2017-04-01

    Turbulence Heating ObserveR (THOR) is the first mission ever flown in space dedicated to plasma turbulence. The fluxgate Magnetometer (MAG) measures the background to low frequency magnetic field. The high sensitivity measurements of MAG enable to characterize the nature of turbulent fluctuations as well as the large-scale context. MAG will provide the reference system for determining anisotropy of field fluctuations, pitch-angle and gyro-phase of particles. The design of the magnetometer consists of two tri-axial sensors and the related magnetometer electronics; the electronics are hosted on printed circuit boards in the common electronics box of the fields and wave processor (FWP). A fully redundant two- sensor system mounted on a common boom and the new miniaturized low noise design based on MMS and Solar Orbiter instruments enable accurate measurement throughout the region of interest for THOR science. The usage of the common electronics hosted by FWP guarantees to fulfill the required timing accuracy with other fields measurements. These improvements are important to obtain precise measurements of magnetic field, which is essential to estimate basic plasma parameters and correctly identify the spatial and temporal scales of the turbulence. Furthermore, THOR MAG provides high quality data with sufficient overlap with the Search Coil Magnetometer (SCM) in frequency space to obtain full coverage of the wave forms over all the frequencies necessary to obtain the full solar wind turbulence spectrum from MHD to kinetic range with sufficient accuracy. We discuss the role of MAG in THOR key science questions and present the new developments during Phase A such as the finalised instrument design, MAG relevant requirement, and new calibraion schemes.

  11. Scalar Calibration of Vector Magnetometers

    DEFF Research Database (Denmark)

    Merayo, José M.G.; Brauer, Peter; Primdahl, Fritz

    2000-01-01

    The calibration parameters of a vector magnetometer are estimated only by the use of a scalar reference magnetometer. The method presented in this paper differs from those previously reported in its linearized parametrization. This allows the determination of three offsets or signals in the absence...

  12. Scalar magnetometers for space applications

    DEFF Research Database (Denmark)

    Primdahl, Fritz

    magnetometer, offer stability and resolution well suited for the calibration purposes. Recent developments are discussed. The metastable Helium magnetometer also offers quasi-absolute scalar measurements, and the use of semiconductor tuned lasers replacing an RF-excited Helium lamp holds great promise...

  13. A ocean bottom vector magnetometer

    Science.gov (United States)

    Wang, Xiaomei; Teng, Yuntian; Wang, Chen; Ma, Jiemei

    2017-04-01

    The new development instrument with a compact spherical coil system and Overhauser magnetometer for measuring the total strength of the magnetic field and the vectors of strength, Delta inclination - Delta declination, meanwhile we also use a triaxial fluxgate instrument of the traditional instrument for geomagnetic vector filed measurement. The advantages of this method are be calibrated by each other and get good performances with automatic operation, good stability and high resolution. Firstly, a brief description of the instrument measurement principles and the key technologies are given. The instrument used a spherical coil system with 34 coils to product the homogeneous volume inside the coils which is large enough to accommodate the sensor of Overhauser total field sensor; the rest of the footlocker-sized ocean-bottom vector magnetometer consists of equipment to run the sensors and records its data (batteries and a data logger), weight to sink it to the sea floor, a remote-controlled acoustic release and flotation to bring the instrument back to the surface. Finally, the accuracy of the instrument was tested in the Geomagnetic station, and the measurement accuracies of total strength and components were better than 0.2nT and 1nT respectively. The figure 1 shows the development instrument structure. it includes six thick glass spheres which protect the sensor, data logger and batteries from the pressures of the deep sea, meanwhile they also provide recycling positive buoyancy; To cushion the glass, the spheres then go inside yellow plastic "hardhats". The triaxial fluxgate is inside No.1 glass spheres, data logger and batteries are inside No.2 glass spheres, the new vector sensor is inside No.3 glass spheres, acoustic communication unit is inside No.4 glass spheres, No.5 and No.6 glass spheres are empty which only provide recycling positive buoyancy. The figure 2 shows the development instrument Physical photo.

  14. Digitalisation of Fluxgate Magnetometer

    DEFF Research Database (Denmark)

    Pedersen, Erik Bøje

    1999-01-01

    The classical instrument for measuring magnetic fields has for a long period been the analogue fluxgate magnetometer.Based on the sensor technology developed at the Department of Automation, Technical University of Denmark, this kind of instrument has involved into a high precision and reliable...... in digital signal Processors. The basic properties behind the instrument are described and it is shown that the instrument works equally well as the analogue version. The first fully working instrument, based on digital signal processing for the Swedish micro-satellite Astrid-2, is described. Finally...... instrument.However, some problems are still present in the analogue electronics.In this thesis an instrument, based on digital signal processing, is presented. The instrument uses an early digitalisation of the fluxgate sensor signal and derives the magnetic field with mathematical algorithms implemented...

  15. Optically transduced MEMS magnetometer

    Science.gov (United States)

    Nielson, Gregory N; Langlois, Eric

    2014-03-18

    MEMS magnetometers with optically transduced resonator displacement are described herein. Improved sensitivity, crosstalk reduction, and extended dynamic range may be achieved with devices including a deflectable resonator suspended from the support, a first grating extending from the support and disposed over the resonator, a pair of drive electrodes to drive an alternating current through the resonator, and a second grating in the resonator overlapping the first grating to form a multi-layer grating having apertures that vary dimensionally in response to deflection occurring as the resonator mechanically resonates in a plane parallel to the first grating in the presence of a magnetic field as a function of the Lorentz force resulting from the alternating current. A plurality of such multi-layer gratings may be disposed across a length of the resonator to provide greater dynamic range and/or accommodate fabrication tolerances.

  16. Miniature Laser Magnetometer

    Science.gov (United States)

    Slocum, Robert; Brown, Andy

    2011-01-01

    A conceptual design has been developed for a miniature laser magnetometer (MLM) that will measure the scalar magnitude and vector components of near-Earth magnetic fields. The MLM incorporates a number of technical innovations to achieve high-accuracy and high-resolution performance while significantly reducing the size of the laser-pumped helium magnetometer for use on small satellites and unmanned aerial vehicles (UAVs). and electronics sections that has the capability of measuring both the scalar magnetic field magnitude and the vector magnetic field components. Further more, the high-accuracy scalar measurements are used to calibrate and correct the vector component measurements in order to achieve superior vector accuracy and stability. The correction algorithm applied to the vector components for calibration and the same cell for vector and scalar measurements are major innovations. The separate sensor and electronics section of the MLM instrument allow the sensor to be installed on a boom or otherwise located away from electronics and other noisy magnetic components. The MLM s miniaturization will be accomplished through the use of advanced miniaturized components and packaging methods for the MLM sensor and electronics. The MLM conceptual design includes three key innovations. The first is a new non-magnetic laser package that will allow the placement of the laser pump source near the helium cell sensing elements. The second innovation is the design of compact, nested, triaxial Braunbek coils used in the vector measurements that reduce the coil size by a factor of two compared to existing Helmholtz coils with similar field-generation performance. The third innovation is a compact sensor design that reduces the sensor volume by a factor of eight compared to MLM s predecessor.

  17. Alignment of a vector magnetometer to an optical prism

    Science.gov (United States)

    Dietrich, M. R.; Bailey, K. G.; O'Connor, T. P.

    2017-05-01

    A method for alignment of a vector magnetometer to a rigidly attached prism is presented. This enables optical comparison of the magnetometer axes to physical surfaces in the apparatus, and thus an absolute determination of the magnetic field direction in space. This is in contrast with more common techniques, which focus on precise determination of the relative angles between magnetometer axes, and so are more suited to measuring differences in the direction of magnetic fields. Here we demonstrate precision better than 500 μrad on a fluxgate magnetometer, which also gives the coil orthogonality errors to a similar precision. The relative sensitivity of the three axes is also determined, with a precision of about 5 ×10 -4 .

  18. High Accuracy Vector Helium Magnetometer

    Data.gov (United States)

    National Aeronautics and Space Administration — The proposed HAVHM instrument is a laser-pumped helium magnetometer with both triaxial vector and omnidirectional scalar measurement capabilities in a single...

  19. Optical Magnetometer Incorporating Photonic Crystals

    Science.gov (United States)

    Kulikov, Igor; Florescu, Lucia

    2007-01-01

    According to a proposal, photonic crystals would be used to greatly increase the sensitivities of optical magnetometers that are already regarded as ultrasensitive. The proposal applies, more specifically, to a state-of-the-art type of quantum coherent magnetometer that exploits the electromagnetically-induced-transparency (EIT) method for determining a small change in a magnetic field indirectly via measurement of the shift, induced by that change, in the hyperfine levels of resonant atoms exposed to the field.

  20. Magnetogama: an open schematic magnetometer

    Science.gov (United States)

    Wahyudi; Khakhim, Nurul; Kuntoro, Tri; Mardiatno, Djati; Rakhman, Afif; Setyo Handaru, Anas; Akhmad Mufaqih, Adien; Marwan Irnaka, Theodosius

    2017-09-01

    Magnetogama is an open schematic hand-assembled fluxgate magnetometer. Compared to another magnetometer, Magnetogama has more benefit concerning its price and its ease of use. Practically Magnetogama can be utilized either in land or attached to an unmanned aerial vehicle (UAV). Magnetogama was designed to give open access to a cheap and accurate alternative to magnetometer sensor. Therefore it can be used as a standard design which is directly applicable to the low-budget company or education purposes. Schematic, code and several verification tests were presented in this article ensuring its reproducibility. Magnetogama has been tested with two kind of tests: a comparison with two nearest observatories at Learmonth (LRM) and Kakadu (KDU) and the response of magnetic substance.

  1. Digital fluxgate magnetometer: design notes

    International Nuclear Information System (INIS)

    Belyayev, Serhiy; Ivchenko, Nickolay

    2015-01-01

    We presented an approach to understanding the performance of a fully digital fluxgate magnetometer. All elements of the design are important for the performance of the instrument, and the presence of the digital feed-back loop introduces certain peculiarities affecting the noise and dynamic performance of the instrument. Ultimately, the quantisation noise of the digital to analogue converter is found to dominate the noise of the current design, although noise shaping alleviates its effect to some extent. An example of magnetometer measurements on board a sounding rocket is presented, and ways to further improve the performance of the instrument are discussed. (paper)

  2. An improved proton magnetometer for Earth's magnetic field observation

    Science.gov (United States)

    Xiao, Chengyu; Zhang, Shuang; Guo, Xin; Fu, Haoyang

    2015-09-01

    As a precision instrument to measure the earth magnetic field, proton magnetometer is widely used in different fields such as geological survey, buried objects detection and earth field variations. Due to poor signal to noise ratio (SNR) of the system, proton magnetometer suffers from low sensitivity which directly affects the performance. In order to increase the sensitivity, we present an improved proton magnetometer. First, the effect of matching resistance on Q value is discussed to enhance SNR, and high matching resistance has been chosen to improve the Q value of the resonant circuit. Second, noise induced by pre-amplifier is investigated in order to obtain low noise signal, and we adopt the JFET with noise figure less than 0.5dB as the pre-amplifier. Third, by using band-pass filter, low-noise output signal is obtained. Fourth, the method of period measurement based on CPLD is employed to measure frequency of the square wave shaped from the output sinusoidal signal. High precision temperature compensate crystal oscillator (TCXO) has been used to improve the frequency measurement accuracy. Last, experimental data is obtained through field measurements. By calculating the standard deviation, the sensitivity of the improved proton magnetometer is 0.15nT for Earth's magnetic field observation. Experimental results show that the new magnetometer is sensitive to earth field measurement.

  3. An Arduino-Based Magnetometer

    Science.gov (United States)

    McCaughey, Mike

    2017-01-01

    An Arduino-based system with a triple axis magnetometer chip may be used to plot both the strength and direction of the magnetic field of a magnet directly on a sheet of paper. Before taking measurements, it is necessary either to correct for or to eliminate soft and hard iron effects. The same sensor may be used to determine the presence of soft…

  4. Rad-Hard Sigma-Delta 3-channel ADC for Fluxgate Magnetometers, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — The proposed project aims to develop a multi-channel analog to digital converter (ADC) required for a fluxgate magnetometer (EPD) employed on NASA's planetary...

  5. Magnetoresistive magnetometer for space science applications

    International Nuclear Information System (INIS)

    Brown, P; Beek, T; Carr, C; O’Brien, H; Cupido, E; Oddy, T; Horbury, T S

    2012-01-01

    Measurement of the in situ dc magnetic field on space science missions is most commonly achieved using instruments based on fluxgate sensors. Fluxgates are robust, reliable and have considerable space heritage; however, their mass and volume are not optimized for deployment on nano or picosats. We describe a new magnetometer design demonstrating science measurement capability featuring significantly lower mass, volume and to a lesser extent power than a typical fluxgate. The instrument employs a sensor based on anisotropic magnetoresistance (AMR) achieving a noise floor of less than 50 pT Hz −1/2 above 1 Hz on a 5 V bridge bias. The instrument range is scalable up to ±50 000 nT and the three-axis sensor mass and volume are less than 10 g and 10 cm 3 , respectively. The ability to switch the polarization of the sensor's easy axis and apply magnetic feedback is used to build a driven first harmonic closed loop system featuring improved linearity, gain stability and compensation of the sensor offset. A number of potential geospace applications based on the initial instrument results are discussed including attitude control systems and scientific measurement of waves and structures in the terrestrial magnetosphere. A flight version of the AMR magnetometer will fly on the TRIO-CINEMA mission due to be launched in 2012. (paper)

  6. Magnetometer with a miniature transducer and automatic scanning

    Science.gov (United States)

    Debnam, W. J. J.; Fales, C. L., Jr.; Breckenridge, R. A.; Pohm, A. V. (Inventor)

    1978-01-01

    The magnetometer is based on the time variation of the magnetic permeability in the magnetic material of its transducer; however, its operation is substantially different from the ordinary flux-gate magnetometer. The transducer uses 0.05 mm diameter plated magnetic wire and is made flat enabling it to make measurements of transverse magnetic fields as close as 0.08 mm from the surface, and it has very good spatial resolution because of its small active region of approximately 0.64 mm by 0.76 mm. The magnetometer uses an inexpensive clip-on millimeter for driving and processing the electrical signals and readout. It also utilizes an automatic scanning technique which is made possible by a specially designed transducer holding mechanism that replaces the ink pen on an X-Y recorder.

  7. Calibration of three-axis magnetometers with differential evolution algorithm

    Energy Technology Data Exchange (ETDEWEB)

    Pang, Hongfeng, E-mail: panghongfeng@126.com [College of Mechatronics Engineering and Automation, National University of Defense Technology, Changsha 410073 (China); Zhang, Qi [College of Mechatronics Engineering and Automation, National University of Defense Technology, Changsha 410073 (China); Wang, Wei [Northwest Institute of Nuclear Technology, Xian 710024 (China); Wang, Junya; Li, Ji; Luo, Shitu; Wan, Chengbiao; Chen, Dixiang; Pan, Mengchun; Luo, Feilu [College of Mechatronics Engineering and Automation, National University of Defense Technology, Changsha 410073 (China)

    2013-11-15

    The accuracy of three-axis magnetometers is influenced by different scale and bias of each axis and nonorthogonality between axes. One limitation of traditional iteration methods is that initial parameters influence the calibration, thus leading to the local optimal or wrong results. In this paper, a new method is proposed to calibrate three-axis magnetometers. To employ this method, a nonmagnetic rotation platform, a proton magnetometer, a DM-050 three-axis magnetometer and the differential evolution (DE) algorithm are used. The performance of this calibration method is analyzed with simulation and experiment. In simulation, the calibration results of DE, unscented Kalman filter (UKF), recursive least squares (RLS) and genetic algorithm (GA) are compared. RMS error using DE is least, which is reduced from 81.233 nT to 1.567 nT. Experimental results show that comparing with UKF, RLS and GA, the DE algorithm has not only the least calibration error but also the best robustness. After calibration, RMS error is reduced from 68.914 nT to 2.919 nT. In addition, the DE algorithm is not sensitive to initial parameters, which is an important advantage compared with traditional iteration algorithms. The proposed algorithm can avoid the troublesome procedure to select suitable initial parameters, thus it can improve the calibration performance of three-axis magnetometers. - Highlights: • The calibration results and robustness of UKF, GA, RLS and DE algorithm are analyzed. • Calibration error of DE is the least in simulation and experiment. • Comparing with traditional calibration algorithms, DE is not sensitive to initial parameters. • It can improve the calibration performance of three-axis magnetometers.

  8. Calibration of three-axis magnetometers with differential evolution algorithm

    International Nuclear Information System (INIS)

    Pang, Hongfeng; Zhang, Qi; Wang, Wei; Wang, Junya; Li, Ji; Luo, Shitu; Wan, Chengbiao; Chen, Dixiang; Pan, Mengchun; Luo, Feilu

    2013-01-01

    The accuracy of three-axis magnetometers is influenced by different scale and bias of each axis and nonorthogonality between axes. One limitation of traditional iteration methods is that initial parameters influence the calibration, thus leading to the local optimal or wrong results. In this paper, a new method is proposed to calibrate three-axis magnetometers. To employ this method, a nonmagnetic rotation platform, a proton magnetometer, a DM-050 three-axis magnetometer and the differential evolution (DE) algorithm are used. The performance of this calibration method is analyzed with simulation and experiment. In simulation, the calibration results of DE, unscented Kalman filter (UKF), recursive least squares (RLS) and genetic algorithm (GA) are compared. RMS error using DE is least, which is reduced from 81.233 nT to 1.567 nT. Experimental results show that comparing with UKF, RLS and GA, the DE algorithm has not only the least calibration error but also the best robustness. After calibration, RMS error is reduced from 68.914 nT to 2.919 nT. In addition, the DE algorithm is not sensitive to initial parameters, which is an important advantage compared with traditional iteration algorithms. The proposed algorithm can avoid the troublesome procedure to select suitable initial parameters, thus it can improve the calibration performance of three-axis magnetometers. - Highlights: • The calibration results and robustness of UKF, GA, RLS and DE algorithm are analyzed. • Calibration error of DE is the least in simulation and experiment. • Comparing with traditional calibration algorithms, DE is not sensitive to initial parameters. • It can improve the calibration performance of three-axis magnetometers

  9. Optical vibrating-sample magnetometer

    CERN Document Server

    Diaz-Michelena, M; López, E; Sanchez, M C; Aroca, C

    2000-01-01

    A highly sensitive method of detecting vibrations of a cantilever in atomic-force microscopy has been introduced as a detector in an alternating-gradient field magnetometer. Use of light is the success of this system as it is compatible with vacuum systems and closed-flux cryostats. The optical signal is electronically conditioned easily. Experimental results show that highly sensitive measurements can be achieved.

  10. Atomic magnetometer for human magnetoencephalograpy.

    Energy Technology Data Exchange (ETDEWEB)

    Schwindt, Peter; Johnson, Cort N.

    2010-12-01

    We have developed a high sensitivity (<5 fTesla/{radical}Hz), fiber-optically coupled magnetometer to detect magnetic fields produced by the human brain. This is the first demonstration of a noncryogenic sensor that could replace cryogenic superconducting quantum interference device (SQUID) magnetometers in magnetoencephalography (MEG) and is an important advance in realizing cost-effective MEG. Within the sensor, a rubidium vapor is optically pumped with 795 laser light while field-induced optical rotations are measured with 780 nm laser light. Both beams share a single optical axis to maximize simplicity and compactness. In collaboration with neuroscientists at The Mind Research Network in Albuquerque, NM, the evoked responses resulting from median nerve and auditory stimulation were recorded with the atomic magnetometer and a commercial SQUID-based MEG system with signals comparing favorably. Multi-sensor operation has been demonstrated with two AMs placed on opposite sides of the head. Straightforward miniaturization would enable high-density sensor arrays for whole-head magnetoencephalography.

  11. Search for plant biomagnetism with a sensitive atomic magnetometer

    OpenAIRE

    Corsini, Eric; Acosta, Victor; Baddour, Nicolas; Higbie, James; Lester, Brian; Licht, Paul; Patton, Brian; Prouty, Mark; Budker, Dmitry

    2010-01-01

    We report what we believe is the first experimental limit placed on plant biomagnetism. Measurements with a sensitive atomic magnetometer were performed on the Titan arum (Amorphophallus titanum) inflorescence, known for its fast bio-chemical processes while blooming. We find that the surface magnetic field from these processes, projected along the Earth's magnetic field, and measured at the surface of the plant, is less then ~0.6uG.

  12. A Complete Cubesat Magnetometer System Project

    Science.gov (United States)

    Zesta, Eftyhia

    2014-01-01

    The objective of this work is to provide the center with a fully tested, flexible, low cost, miniaturized science magnetometer system applicable to small satellite programs, like Cubesats, and to rides of opportunity that do not lend themselves to the high integration costs a science magnetometer on a boom necessitates.

  13. The Noise Level Optimization for Induction Magnetometer of SEP System

    Science.gov (United States)

    Zhu, W.; Fang, G.

    2011-12-01

    The Surface Electromagnetic Penetration (SEP) System, subsidized by the SinoProbe Plan in China, is designed for 3D conductivity imaging in geophysical mineral exploration, underground water distribution exploration, oil and gas reservoir exploration. Both the Controlled Source Audio Magnetotellurics (CSAMT) method and Magnetotellurics (MT) method can be surveyed by SEP system. In this article, an optimization design is introduced, which can minimize the noise level of the induction magnetometer for SEP system magnetic field's acquisition. The induction magnetometer transfers the rate of the magnetic field's change to voltage signal by induction coil, and amplified it by Low Noise Amplifier The noise parts contributed to the magnetometer are: the coil's thermal noise, the equivalent input voltage and current noise of the pre-amplifier. The coil's thermal noise is decided by coil's DC resistance. The equivalent input voltage and current noise of the pre-amplifier depend on the amplifier's type and DC operation condition. The design here optimized the DC operation point of pre-amplifier, adjusted the DC current source, and realized the minimum of total noise level of magnetometer. The calculation and test results show that: the total noise is about 1pT/√Hz, the thermal noise of coils is 1.7nV/√Hz, the preamplifier equivalent input voltage and current noise is 3nV/ √Hz and 0.1pA/√Hz, the weight of the magnetometer is 4.5kg and meet the requirement of SEP system.

  14. Search for plant biomagnetism with a sensitive atomic magnetometer

    Science.gov (United States)

    Corsini, Eric; Acosta, Victor; Baddour, Nicolas; Higbie, James; Lester, Brian; Licht, Paul; Patton, Brian; Prouty, Mark; Budker, Dmitry

    2011-04-01

    We report what we believe is the first experimental limit placed on plant biomagnetism. Measurements with a sensitive atomic magnetometer were performed on the Titan arum (Amorphophallus titanum) inflorescence, known for its fast biochemical processes while blooming. We find that the magnetic field from these processes, projected along the Earth's magnetic field, and measured at the surface of the plant, is ≲ 0.6 μG.

  15. Nuclear quantum-assisted magnetometer

    Science.gov (United States)

    Häberle, Thomas; Oeckinghaus, Thomas; Schmid-Lorch, Dominik; Pfender, Matthias; de Oliveira, Felipe Fávaro; Momenzadeh, Seyed Ali; Finkler, Amit; Wrachtrup, Jörg

    2017-01-01

    Magnetic sensing and imaging instruments are important tools in biological and material sciences. There is an increasing demand for attaining higher sensitivity and spatial resolution, with implementations using a single qubit offering potential improvements in both directions. In this article we describe a scanning magnetometer based on the nitrogen-vacancy center in diamond as the sensor. By means of a quantum-assisted readout scheme together with advances in photon collection efficiency, our device exhibits an enhancement in signal to noise ratio of close to an order of magnitude compared to the standard fluorescence readout of the nitrogen-vacancy center. This is demonstrated by comparing non-assisted and assisted methods in a T1 relaxation time measurement.

  16. Development of a nuclear precession magnetometer

    International Nuclear Information System (INIS)

    Virgens Alves, J.G. das.

    1983-12-01

    The objective of this thesis was to develop a proton precession magnetometer for geophysical prospecting and base stations. The proton procession magnetometer measures the total magnetic fields intensity. It operates on the basis of nuclear magnetic resonance by determining the processing frequency of protons of a non viscous liquid in the terrestrial magnetic fields. The instrument was tested in field to evaluate signal/noise ratio, supportable gradient and battery consumption. Application test was carried out to take diurnal variation data and, reconnaissance and detail surveys data on an archaeological site in the Marajo Island-Pa. The test results were confronted with two commercial magnetometers-GP-70, McPhar e G-816, Geometric - and, with data from Observatorio Magnetico Ilha de Tatuoca as well. For all cases, the data comparison showed a good performance of the magnetometer tested. (author)

  17. All optical vector magnetometer, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — This Phase I research project will investigate a novel method of operating an atomic magnetometer to simultaneously measure total magnetic fields and vector magnetic...

  18. CubeSat Magnetometer, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Sensitive magnetometers play a key role in exploring the near-Earth environment, other planets and moons. Measurements using a constellation of spacecraft can...

  19. Miniature Laser Magnetometer (MLM), Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — This 2009 NASA SBIR Phase 1 proposal for an innovative Miniature Laser Magnetometer (MLM) is a response to subtopic S1.06 Particles and Field Sensors and Instrument...

  20. GALILEO MAGNETOMETER CRUISE DATA (IRC COORDINATES)

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set contains data acquired by the Galileo Magnetometer during the Interplanetary Cruise to Jupiter. The data are at varying resolution depending on the...

  1. ICE MAGNETOMETER DATA V1.0

    Data.gov (United States)

    National Aeronautics and Space Administration — These data were obtained from the JPL magnetometer experiment on ICE (Principal Investigator: E.J. Smith produces three, high-accuracy, triaxial measurements per...

  2. Magnetometer Data recovered from 35mm film

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The L57 CDMP recovery project takes magnetometer data on 35mm film stored at the archive's climate controlled warehouse and digitizes them.

  3. Miniature Laser Magnetometer (MLM), Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — This 2009 NASA SBIR Phase 2 proposal for an innovative Miniature Laser Magnetometer (MLM) is a response to subtopic S1.06 Particles and Field Sensors and Instrument...

  4. Directly coupled YBCO dc SQUID magnetometers

    International Nuclear Information System (INIS)

    Petersen, P.R.E.; Shen, Y.Q.; Holst, T.; Larsen, B.H.; Sager, M.P.; Bindslev Hansen, J.

    1999-01-01

    YBa 2 Cu 3 O 7- x magnetometers have been made on 10mmx10mm MgO substrates by directly coupling the magnetometer pick-up loop to a dc SQUID with narrow strip lines. The dc SQUIDs were made with YBa 2 Cu 3 O 7-x step-edge Josephson junctions. The layout of the magnetometer pick-up loop was chosen as a compromise between maximizing the loop effective area and minimizing the loop inductance. The SQUID was designed to have L S ∼100 pH in order to obtain β L =2I 0 L S /Φ 0 approx.= 1 with the single-junction critical current I 0 ∼10 μA. We have made magnetometers with white noise levels down to 55 fT Hz -1/2 and a 1/f knee at 1 Hz (ac biased). Noise measurements were made on a field-cooled magnetometer. The noise measured at 1 Hz when cooled in 'zero field' was 175 fT Hz -1/2 . When cooled in magnetic fields of B = 50 μT and B = 100 μT we measured the noise at 1 Hz to be 430 fT Hz -1 2 and 1.3 pT Hz -1/2 , respectively. (author)

  5. Magnetometer for measuring planetary magnetic fields

    DEFF Research Database (Denmark)

    Merayo, José M.G.; Brauer, Peter

    . The mass, power and volume are important factors when designing planetary magnetometers. However, the performance must not be compromised. The DTU magnetometer consisting of a triaxial fluxgate sensor and controlling electronics is a miniaturized version of the instruments flown on the Oersted, Astrid-2......, CHAMP and SAC-C missions. It can produce vector measurements at a rate of 50 Hz and with a precision of more than 21 bits. The thermal and long term stability of the instrument is less than 0.5 nT. The power consumption of the instrument is less than 0.5W for continuous operation. For an orbiting...

  6. Developments in convective heat transfer models featuring seamless and selected detail surfaces, employing electroless plating

    Science.gov (United States)

    Stalmach, C. J., Jr.

    1975-01-01

    Several model/instrument concepts employing electroless metallic skin were considered for improvement of surface condition, accuracy, and cost of contoured-geometry convective heat transfer models. A plated semi-infinite slab approach was chosen for development and evaluation in a hypersonic wind tunnel. The plated slab model consists of an epoxy casting containing fine constantan wires accurately placed at specified surface locations. An electroless alloy was deposited on the plastic surface that provides a hard, uniformly thick, seamless skin. The chosen alloy forms a high-output thermocouple junction with each exposed constantan wire, providing means of determining heat transfer during tunnel testing of the model. A selective electroless plating procedure was used to deposit scaled heatshield tiles on the lower surface of a 0.0175-scale shuttle orbiter model. Twenty-five percent of the tiles were randomly selected and plated to a height of 0.001-inch. The purpose was to assess the heating effects of surface roughness simulating misalignment of tiles that may occur during manufacture of the spacecraft.

  7. A Visual Detection System for Determining Tritium Surface Deposition Employing Phosphor Coated Materials

    International Nuclear Information System (INIS)

    Gentile, C.A.; Skinner, C.H.; Young, K.M.; Zweben, S.J.

    1999-01-01

    A method for visually observing tritium deposition on the surface of the Tokamak Fusion Test Reactor (TFTR) deuterium-tritium (D-T) tiles is being investigated at the Princeton Plasma Physics Laboratory. A green phosphor (P31, zinc sulfide: copper) similar to that used in oscilloscope screens with a wavelength peak of 530 nm was positioned on the surface of a TFTR D-T tile. The approximately 600 gram tile, which contains approximately 1.5 Ci of tritium located on the top approximately 1-50 microns of the surface, was placed in a two liter lexan chamber at Standard Temperature and Pressure (STP). The phosphor plates and phosphor powder were placed on the surface of the tile which resulted in visible light being observed, the consequence of tritium betas interacting with the phosphor. This technique provides a method of visually observing varying concentrations of tritium on the surface of D-T carbon tiles, and may be employed (in a calibrated system) to obtain quantitative data

  8. Superconductive quantum interference magnetometer with high sensitivity achieved by an induced resonance

    Energy Technology Data Exchange (ETDEWEB)

    Vettoliere, A.; Granata, C., E-mail: c.granata@cib.na.cnr.it [Istituto di Cibernetica “E. Caianiello” del Consiglio Nazionale delle Ricerche, I-80078 Pozzuoli, Napoli (Italy)

    2014-08-15

    A fully integrated low noise superconducting quantum interference device (SQUID) in a magnetometer configuration is presented. An intrinsic high voltage responsivity as high as 500 μV/Φ{sub 0} has been obtained by introducing a resonance in the voltage – magnetic flux characteristic. This resonance is induced by an integrated superconducting coil surrounding the pick-up coil and connected to one end of the SQUID output. The SQUID magnetometer exhibits a spectral density of magnetic field noise as low as 3 fT/Hz{sup 1/2}. In order to verify the suitability of the magnetometer, measurements of bandwidth and slew rate have been performed and compared with those of the same device without the resonance and with additional positive feedback. Due to their good characteristics such devices can be employed in a large number of applications including biomagnetism.

  9. Superconductive quantum interference magnetometer with high sensitivity achieved by an induced resonance

    Science.gov (United States)

    Vettoliere, A.; Granata, C.

    2014-08-01

    A fully integrated low noise superconducting quantum interference device (SQUID) in a magnetometer configuration is presented. An intrinsic high voltage responsivity as high as 500 μV/Φ0 has been obtained by introducing a resonance in the voltage - magnetic flux characteristic. This resonance is induced by an integrated superconducting coil surrounding the pick-up coil and connected to one end of the SQUID output. The SQUID magnetometer exhibits a spectral density of magnetic field noise as low as 3 fT/Hz1/2. In order to verify the suitability of the magnetometer, measurements of bandwidth and slew rate have been performed and compared with those of the same device without the resonance and with additional positive feedback. Due to their good characteristics such devices can be employed in a large number of applications including biomagnetism.

  10. Calibration of the fluxgate CSC vector magnetometers

    DEFF Research Database (Denmark)

    Merayo, José M.G.; Risbo, Torben; Primdahl, Fritz

    1995-01-01

    This report shows the results of the calibration of the flight and flight spare CSC magnetometers for the Ørsted satellite. The instrument shows an outstanding behavior as regards of both constant temperature and temperature dependance. Neither transverse effects nor non-linear terms have been fo...

  11. Automated system for the calibration of magnetometers

    DEFF Research Database (Denmark)

    Petrucha, Vojtech; Kaspar, Petr; Ripka, Pavel

    2009-01-01

    A completely nonmagnetic calibration platform has been developed and constructed at DTU Space (Technical University of Denmark). It is intended for on-site scalar calibration of high-precise fluxgate magnetometers. An enhanced version of the same platform is being built at the Czech Technical Uni...

  12. Determination of the Overhauser magnetometer uncertainty

    Czech Academy of Sciences Publication Activity Database

    Ulvr, M.; Zikmund, A.; Kupec, J.; Janošek, M.; Vlk, Michal; Bayer, Tomáš

    2015-01-01

    Roč. 66, 7/s (2015), s. 26-29 ISSN 1335-3632 Institutional support: RVO:67985530 Keywords : Overhauser magnetometer * Earth`s magnetic field * comparison * uncertainty Subject RIV: DE - Earth Magnetism, Geodesy, Geography Impact factor: 0.407, year: 2015

  13. Digitalization of highly precise fluxgate magnetometers

    DEFF Research Database (Denmark)

    Cerman, Ales; Kuna, A.; Ripka, P.

    2005-01-01

    the Delta-Sigma ADCs are mostly used for the digitalization of the highly precise fluxgate magnetorneters. The relevant part of the paper demonstrates some pitfalls of their application studied during the design of the magnetometer for the new Czech scientific satellite MIMOSA. The part discussing...

  14. Vector Magnetometer Application with Moving Carriers

    Directory of Open Access Journals (Sweden)

    Andrii Prystai

    2016-12-01

    Full Text Available In magnetic prospecting the aeromagnetic survey is a widespread method used for research in large territories or in the areas with difficult access (forests, swamps, shallow waters. At present, a new type of mobile carriers – remotely piloted vehicles or drones – is becoming very common. The drones supplied by magnetometer can be also used for underground utility location (for example, steel and concrete constructions, buried power cables, to name a few. For aeromagnetic survey, obtaining of 3-component magnetic field data gives higher processing precision, so the fluxgate magnetometers (FGM seem to be the most preferable by reason of low weight, noise, power consumption and costs. During movement of FGM fixed to a drone practically permanent attitude changes in the Earth’s magnetic field arises with corresponding changes of its projection at FGM axes. Also the electromagnetic interference from the drone motor and uncontrolled oscillations of drone and suspension are the factors which limit the magnetometer sensitivity level. Aroused because of this, signals significantly exceed the expected signals from a studied object and so should be removed by proper interference filtration and use of stabilized towed construction, as well as at data processing. To find the necessary resolution threshold of a drone-portable FGM, the modeling was made to estimate magnetic field value from a small sphere about 1 cm radius at the minimal altitude of drone flight and it was shown that such a small object can be reliably detected if the FGM noise level is less than 0.15 nT. Next requirement is the necessity to decrease as much as possible the FGM power consumption with retention of low noise level. Finally, because of drone movement, the broadening of a frequency range should be done. The LEMI-026 magnetometer was developed satisfying all requirements to the drone-mounted device. The field tests were successfully performed using two of LEMI-026

  15. Midlatitude magnetometer chains during the IMS

    International Nuclear Information System (INIS)

    Mcpherron, R.L.

    1982-01-01

    The International Magnetospheric Study (IMS) is an international program to study global problems of magnetospheric dynamics. A key element of the U.S. participation in this program was the establishment of a ground magnetometer network. This network included a number of arrays at high and low latitudes. This report describes three chains established at midlatitudes, including the IMS Midlatitude Chain, the AFGL Magnetometer Network, and the Bell Lab Conjugate Array. Descriptions of the type of equipment, station locations, types of data display, and availability of data for each chain are presented in this report. A major problem of the data analysis phase of the IMS will be reducing selected subsets of these data to a common format. Currently, there are no plans to do this in a systematic manner

  16. A Web Server for MACCS Magnetometer Data

    Science.gov (United States)

    Engebretson, Mark J.

    1998-01-01

    NASA Grant NAG5-3719 was provided to Augsburg College to support the development of a web server for the Magnetometer Array for Cusp and Cleft Studies (MACCS), a two-dimensional array of fluxgate magnetometers located at cusp latitudes in Arctic Canada. MACCS was developed as part of the National Science Foundation's GEM (Geospace Environment Modeling) Program, which was designed in part to complement NASA's Global Geospace Science programs during the decade of the 1990s. This report describes the successful use of these grant funds to support a working web page that provides both daily plots and file access to any user accessing the worldwide web. The MACCS home page can be accessed at http://space.augsburg.edu/space/MaccsHome.html.

  17. A high-performance lab-on-a-chip liquid sensor employing surface acoustic wave resonance

    Science.gov (United States)

    Kustanovich, K.; Yantchev, V.; Kirejev, V.; Jeffries, G. D. M.; Lobovkina, T.; Jesorka, A.

    2017-11-01

    We demonstrate herein a new concept for lab-on-a-chip in-liquid sensing, through integration of surface acoustic wave resonance (SAR) in a one-port configuration with a soft polymer microfluidic delivery system. In this concept, the reflective gratings of a one-port surface acoustic wave (SAW) resonator are employed as mass loading-sensing elements, while the SAW transducer is protected from the measurement environment. We describe the design, fabrication, implementation, and characterization using liquid medium. The sensor operates at a frequency of 185 MHz and has demonstrated a comparable sensitivity to other SAW in-liquid sensors, while offering quality factor (Q) value in water of about 250, low impedance and fairly low susceptibility to viscous damping. For proof of principle, sensing performance was evaluated by means of binding 40 nm neutravidin-coated SiO2 nanoparticles to a biotin-labeled lipid bilayer deposited over the reflectors. Frequency shifts were determined for every step of the affinity assay. Demonstration of this integrated technology highlights the potential of SAR technology for in-liquid sensing.

  18. Calibration of Magnetometers with GNSS Receivers and Magnetometer-Aided GNSS Ambiguity Fixing.

    Science.gov (United States)

    Henkel, Patrick

    2017-06-08

    Magnetometers provide compass information, and are widely used for navigation, orientation and alignment of objects. As magnetometers are affected by sensor biases and eventually by systematic distortions of the Earth magnetic field, a calibration is needed. In this paper, a method for calibration of magnetometers with three Global Navigation Satellite System (GNSS) receivers is presented. We perform a least-squares estimation of the magnetic flux and sensor biases using GNSS-based attitude information. The attitude is obtained from the relative positions between the GNSS receivers in the North-East-Down coordinate frame and prior knowledge of these relative positions in the platform's coordinate frame. The relative positions and integer ambiguities of the periodic carrier phase measurements are determined with an integer least-squares estimation using an integer decorrelation and sequential tree search. Prior knowledge on the relative positions is used to increase the success rate of ambiguity fixing. We have validated the proposed method with low-cost magnetometers and GNSS receivers on a vehicle in a test drive. The calibration enabled a consistent heading determination with an accuracy of five degrees. This precise magnetometer-based attitude information allows an instantaneous GNSS integer ambiguity fixing.

  19. Development of autonomous magnetometer rotorcraft for wide area assessment

    Energy Technology Data Exchange (ETDEWEB)

    Roelof Versteeg; Matt Anderson; Les Beard; Eric Corban; Darryl Curley; Jeff Gamey; Ross Johnson; Dwight Junkin; Mark McKay; Jared Salzmann; Mikhail Tchernychev; Suraj Unnikrishnan; Scott Vinson

    2010-04-01

    Large areas across the United States are potentially contaminated with UXO, with some ranges encompassing tens to hundreds of thousands of acres. Technologies are needed which will allow for cost effective wide area scanning with 1) near 100 % coverage and 2) near 100 % detection of subsurface ordnance or features indicative of subsurface ordnance. The current approach to wide area assessment is a multi-level one, in which medium - altitude fixed wing optical imaging is used for an initial site assessment. This assessment is followed with low altitude manned helicopter based magnetometry. Subsequent to this wide area assessment targeted surface investigations are performed using either towed geophysical sensor arrays or man portable sensors. In order to be an effective tool for small UXO detection, the sensing altitude for magnetic site investigations needs to be on the order of 1 – 3 meters. These altitude requirements mean that manned helicopter surveys will generally only be feasible in large, open and relatively flat terrains. While such surveys are effective in mapping large areas relatively fast there are substantial mobilization/demobilization, staffing and equipment costs associated with these surveys (resulting in costs of approximately $100-$150/acre). In addition, due to the low altitude there are substantial risks to pilots and equipment. Surface towed arrays provide high resolution maps but have other limitations, e.g. in their ability to navigate rough terrain effectively. There is thus a need for other systems which can be used for effective data collection. An UAV (Unmanned Aerial Vehicle) magnetometer platform is an obvious alternative. The motivation behind such a system is that it reduces risk to operators, is lower in initial and Operational and Maintenance (O&M) costs (and can thus potentially be applied to smaller sites) and has the potential of being more effective in terms of detection and possibly characterization (through the use of

  20. Estimation of Aeolian Dune Migration Over Martian Surface Employing High Precision Photogrammetric Measurements

    Science.gov (United States)

    Kim, J.

    2017-07-01

    At the present time, arguments continue regarding the migration speeds of Martian dune fields and their correlation with atmospheric circulation. However, precisely measuring the spatial translation of Martian dunes has been rarely successful due to the technical difficulties to quantitatively observe expected small surface migrations. Therefore, we developed a generic procedure to measure the migration of dune fields employing a high-accuracy photogrammetric processor and sub-pixel image correlator on the 25-cm resolution High Resolution Imaging Science Experiment (HiRISE). The established algorithms have been tested over a few Martian dune fields. Consequently, migrations over well-known crater dune fields appeared to be almost static for the considerable temporal periods and were weakly correlated with wind directions estimated by the Mars Climate Database. Only over some Martian dune fields, such as Kaiser crater, meaningful migration speeds (> 1m/year) considering photogrammetric error residual have been detected. Currently a technically improved processor to compensate error residual using time series observation is under development and expected to produce the long term migration speed over Martian dune fields where constant HiRISE image acquisitions are available.

  1. ESTIMATION OF AEOLIAN DUNE MIGRATION OVER MARTIAN SURFACE EMPLOYING HIGH PRECISION PHOTOGRAMMETRIC MEASUREMENTS

    Directory of Open Access Journals (Sweden)

    J. Kim

    2017-07-01

    Full Text Available At the present time, arguments continue regarding the migration speeds of Martian dune fields and their correlation with atmospheric circulation. However, precisely measuring the spatial translation of Martian dunes has been rarely successful due to the technical difficulties to quantitatively observe expected small surface migrations. Therefore, we developed a generic procedure to measure the migration of dune fields employing a high-accuracy photogrammetric processor and sub-pixel image correlator on the 25-cm resolution High Resolution Imaging Science Experiment (HiRISE. The established algorithms have been tested over a few Martian dune fields. Consequently, migrations over well-known crater dune fields appeared to be almost static for the considerable temporal periods and were weakly correlated with wind directions estimated by the Mars Climate Database. Only over some Martian dune fields, such as Kaiser crater, meaningful migration speeds (> 1m/year considering photogrammetric error residual have been detected. Currently a technically improved processor to compensate error residual using time series observation is under development and expected to produce the long term migration speed over Martian dune fields where constant HiRISE image acquisitions are available.

  2. The atomic magnetometer: A new era in biomagnetism

    Energy Technology Data Exchange (ETDEWEB)

    Wakai, Ronald T., E-mail: rtwakai@wisc.edu [1005 Wisconsin Institutes for Medical Research, 1111 Highland Avenue, University of Wisconsin-Madison, Madison, Wisconsin 53705 (United States)

    2014-11-07

    The high cost and impracticality of SQUID (Superconducting QUantum Interference Device) magnetometers has limited the expansion of magnetoencephalography (MEG) and magnetocardiography (MCG), especially in countries where the cost of liquid helium is high. A recent breakthrough, however, has the potential to radically change this situation. In 2003, a group at Princeton University demonstrated an atomic magnetometer, known as the SERF (spin-exchange free relaxation) magnetometer, with unprecedented sensitivity. Since then, several research groups have utilized SERF magnetometers to record MEG, MCG, and fetal MCG signals. Despite some modest drawbacks, it now seems almost certain that SERF magnetometers can replace SQUIDs for many applications. With a price tag that is likely to be far less than that of SQUIDs, SERF magnetometers can propel the next wave of growth in biomagnetism.

  3. The atomic magnetometer: A new era in biomagnetism

    Science.gov (United States)

    Wakai, Ronald T.

    2014-11-01

    The high cost and impracticality of SQUID (Superconducting QUantum Interference Device) magnetometers has limited the expansion of magnetoencephalography (MEG) and magnetocardiography (MCG), especially in countries where the cost of liquid helium is high. A recent breakthrough, however, has the potential to radically change this situation. In 2003, a group at Princeton University demonstrated an atomic magnetometer, known as the SERF (spin-exchange free relaxation) magnetometer, with unprecedented sensitivity. Since then, several research groups have utilized SERF magnetometers to record MEG, MCG, and fetal MCG signals. Despite some modest drawbacks, it now seems almost certain that SERF magnetometers can replace SQUIDs for many applications. With a price tag that is likely to be far less than that of SQUIDs, SERF magnetometers can propel the next wave of growth in biomagnetism.

  4. Composite Rolled Magnetometer and Instrument Boom, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Magnetometers are the most common instrument flown on NASA science missions and interference from onboard electronics requires that these instruments be deployed...

  5. High Tc Josephson Junctions, SQUIDs and magnetometers

    International Nuclear Information System (INIS)

    Clarke, J.

    1991-01-01

    There has recently been considerable progress in the state-of-the-art of high-T c magnetometers based on dc SQUIDs (Superconducting Quantum Interference Devices). This progress is due partly to the development of more manufacturable Josephson junctions, making SQUIDs easier to fabricate, and partly to the development of multiturn flux transformers that convert the high sensitivity of SQUIDs to magnetic flux to a correspondingly high sensitivity to magnetic field. Needless to say, today's high-T c SQUIDs are still considerably less sensitive than their low-T c counterparts, particularly at low frequencies (f) where their level of 1/f noise remains high. Nonetheless, the performance of the high-T c devices has now reached the point where they are adequate for a number of the less demanding applications; furthermore, as we shall see, at least modest improvements in performance are expected in the near future. In this article, the author outlines these various developments. This is far from a comprehensive review of the field, however, and, apart from Sec. 2, he describes largely his own work. He begins in Sec. 2 with an overview of the various types of Josephson junctions that have been investigated, and in Sec. 3, he describes some of the SQUIDs that have been tested, and assess their performance. Section 4 discuss the development of the multilayer structures essential for an interconnect technology, and, in particular, for crossovers and vias. Section 5 shows how this technology enables one to fabricate multiturn flux transformers which, in turn, can be coupled to SQUIDs to make magnetometers. The performance and possible future improvements in these magnetometers are assessed, and some applications mentioned

  6. Performances and place of magnetometers based on amorphous wires compared to conventional magnetometers

    International Nuclear Information System (INIS)

    Robbes, D.; Dolabdjian, C.; Monfort, Y.

    2002-01-01

    We discuss and compare performances of various room temperature magnetometers. The work is directed towards the search of those magnetometers having a high sensitivity (>1000 V/T), a very low noise level (>1 pT/√Hz at white noise) attainable in a volume typically smaller than 1 cm 3 . The choice of this set of parameters is related to the useful comparison of room temperature magnetometers versus cryogenic ones, such as Superconducting Quantum Interferometer Devices (SQUIDs). The latter have highly degraded performances when their working operations needs an open unshielded environment as required for example in industrial application (non-destructive evaluation). SQUIDs have also a rather poor spatial resolution, and could be replaced by room temperature sensors in some magnetic imaging systems, which require a high spatial resolution. The paper is 'highlighted' in the field of magnetic sensors based on amorphous magnetic wires that were used to carry out wide bandwidth (>100 kHz), very low noise flux gate (∼pT/√Hz at white noise) and highly sensitive, low noise magnetometers (∼pT/√Hz at white noise) Colpitts oscillator configuration use by K. Bushida's

  7. Estimating the Geoelectric Field Using Precomputed EMTFs: Effect of Magnetometer Cadence

    Science.gov (United States)

    Grawe, M.; Butala, M.; Makela, J. J.; Kamalabadi, F.

    2017-12-01

    Studies that make use of electromagnetic transfer functions (EMTFs) to calculate the surface electric field from a specified surface magnetic field often use historical magnetometer information for validation and comparison purposes. Depending on the data source, the magnetometer cadence is typically between 1 and 60 seconds. It is often implied that a 60 (and sometimes 10) second cadence is acceptable for purposes of geoelectric field calculation using a geophysical model. Here, we quantitatively assess this claim under different geological settings and using models of varying complexity (using uniform/1D/3D EMTFs) across several different space weather events. Conclusions are made about sampling rate sufficiency as a function of local geology and the spectral content of the surface magnetic field.

  8. Automated system for the calibration of magnetometers

    Science.gov (United States)

    Petrucha, Vojtech; Kaspar, Petr; Ripka, Pavel; Merayo, Jose M. G.

    2009-04-01

    A completely nonmagnetic calibration platform has been developed and constructed at DTU Space (Technical University of Denmark). It is intended for on-site scalar calibration of high-precise fluxgate magnetometers. An enhanced version of the same platform is being built at the Czech Technical University. There are three axes of rotation in this design (compared to two axes in the previous version). The addition of the third axis allows us to calibrate more complex devices. An electronic compass based on a vector fluxgate magnetometer and micro electro mechanical systems (MEMS) accelerometer is one example. The new platform can also be used to evaluate the parameters of the compass in all possible variations in azimuth, pitch, and roll. The system is based on piezoelectric motors, which are placed on a platform made of aluminum, brass, plastic, and glass. Position sensing is accomplished through custom-made optical incremental sensors. The system is controlled by a microcontroller, which executes commands from a computer. The properties of the system as well as calibration and measurement results will be presented.

  9. Juno Magnetometer Observations in the Earth's Magnetosphere

    Science.gov (United States)

    Connerney, J. E.; Oliversen, R. J.; Espley, J. R.; MacDowall, R. J.; Schnurr, R.; Sheppard, D.; Odom, J.; Lawton, P.; Murphy, S.; Joergensen, J. L.; Joergensen, P. S.; Merayo, J. M.; Denver, T.; Bloxham, J.; Smith, E. J.; Murphy, N.

    2013-12-01

    The Juno spacecraft enjoyed a close encounter with Earth on October 9, 2013, en route to Jupiter Orbit Insertion (JOI) on July 5, 2016. The Earth Flyby (EFB) provided a unique opportunity for the Juno particles and fields instruments to sample mission relevant environments and exercise operations anticipated for orbital operations at Jupiter, particularly the period of intense activity around perijove. The magnetic field investigation onboard Juno is equipped with two magnetometer sensor suites, located at 10 and 12 m from the spacecraft body at the end of one of the three solar panel wings. Each contains a vector fluxgate magnetometer (FGM) sensor and a pair of co-located non-magnetic star tracker camera heads which provide accurate attitude determination for the FGM sensors. This very capable magnetic observatory sampled the Earth's magnetic field at 64 vector samples/second throughout passage through the Earth's magnetosphere. We present observations of the Earth's magnetic field and magnetosphere obtained throughout the encounter and compare these observations with those of other Earth-orbiting assets, as available, and with particles and fields observations acquired by other Juno instruments operated during EFB.

  10. Digital Fluxgate Magnetometer for Detection of Microvibration

    Directory of Open Access Journals (Sweden)

    Menghui Zhi

    2017-01-01

    Full Text Available In engineering practice, instruments, such as accelerometer and laser interferometer, are widely used in vibration measurement of structural parts. A method for using a triaxial fluxgate magnetometer as a microvibration sensor to measure low-frequency pendulum microvibration (not translational vibration is proposed in this paper, so as to detect vibration from low-frequency vibration sources, such as large rotating machine, large engineering structure, earthquake, and microtremor. This method provides vibration detection based on the environmental magnetic field signal to avoid increased measurement difficulty and error due to different relative positions of permanent magnet and magnetometer on the device under test (DUT when using the original magnetic measurement method. After fixedly connecting the fluxgate probe with the DUT during the test, the angular displacement due to vibration can be deduced by measuring the geomagnetic field’s magnetic induction intensity change on the orthogonal three components during the vibration. The test shows that the microvibration sensor has angular resolution of over 0.05° and maximum measuring frequency of 64 Hz. As an exploring test aimed to detect the microvibration of earth-orbiting satellite in the in-orbit process, the simulation experiment successfully provides the real-time microvibration information for attitude and orbit control subsystem.

  11. Calibration of the Ørsted vector magnetometer

    DEFF Research Database (Denmark)

    Olsen, Nils; Tøffner-Clausen, Lars; Sabaka, T.J.

    2003-01-01

    The vector fluxgate magnetometer of the Orsted satellite is routinely calibrated by comparing its output with measurements of the absolute magnetic intensity from the Overhauser instrument, which is the second magnetometer of the satellite. We describe the method used for and the result obtained...

  12. Analysing Harmonic Motions with an iPhone's Magnetometer

    Science.gov (United States)

    Yavuz, Ahmet; Temiz, Burak Kagan

    2016-01-01

    In this paper, we propose an experiment for analysing harmonic motion using an iPhone's (or iPad's) magnetometer. This experiment consists of the detection of magnetic field variations obtained from an iPhone's magnetometer sensor. A graph of harmonic motion is directly displayed on the iPhone's screen using the "Sensor Kinetics"…

  13. Digital fluxgate magnetometer for the "Astrid-2" satellite

    DEFF Research Database (Denmark)

    Pedersen, Erik Bøje; Primdahl, Fritz; Petersen, Jan Raagaard

    1999-01-01

    The design and performance of the Astrid-2 magnetometer are described. The magnetometer uses mathematical routines implemented by software for commercially available digital dignal processors to determine the magnetic field from the fluxgate sensor. The sensor is from the latest generation of amo...

  14. Effect of second harmonic in pulse-width-modulation-based DAC for feedback of digital fluxgate magnetometer

    Science.gov (United States)

    Belyayev, Serhiy; Ivchenko, Nickolay

    2018-04-01

    Digital fluxgate magnetometers employ processing of the measured pickup signal to produce the value of the compensation current. Using pulse-width modulation with filtering for digital to analog conversion is a convenient approach, but it can introduce an intrinsic source of nonlinearity, which we discuss in this design note. A code shift of one least significant bit changes the second harmonic content of the pulse train, which feeds into the pick-up signal chain despite the heavy filtering. This effect produces a code-dependent nonlinearity. This nonlinearity can be overcome by the specific design of the timing of the pulse train signal. The second harmonic is suppressed if the first and third quarters of the excitation period pulse train are repeated in the second and fourth quarters. We demonstrate this principle on a digital magnetometer, achieving a magnetometer noise level corresponding to that of the sensor itself.

  15. Modeling Geomagnetically Induced Currents From Magnetometer Measurements: Spatial Scale Assessed With Reference Measurements

    Science.gov (United States)

    Butala, Mark D.; Kazerooni, Maryam; Makela, Jonathan J.; Kamalabadi, Farzad; Gannon, Jennifer L.; Zhu, Hao; Overbye, Thomas J.

    2017-10-01

    Solar-driven disturbances generate geomagnetically induced currents (GICs) that can result in power grid instability and, in the most extreme cases, even failure. Magnetometers provide direct measurements of the geomagnetic disturbance (GMD) effect on the surface magnetic field and GIC response can be determined from the power grid topology and engineering parameters. This paper considers this chain of models: transforming surface magnetic field disturbance to induced surface electric field through an electromagnetic transfer function and, then, induced surface electric field to GIC using the PowerWorld simulator to model a realistic power grid topology. Comparisons are made to transformer neutral current reference measurements provided by the American Transmission Company. Three GMD intervals are studied, with the Kp index reaching 8- on 2 October 2013, 7 on 1 June 2013, and 6- on 9 October 2013. Ultimately, modeled to measured GIC correlations are analyzed as a function of magnetometer to GIC sensor distance. Results indicate that modeling fidelity during the three studied GMD intervals is strongly dependent on both magnetometer to substation transformer baseline distance and GMD intensity.

  16. An absolute nuclear magnetic resonance magnetometer

    International Nuclear Information System (INIS)

    Salvi, A.

    1961-10-01

    After an introduction in which the various work undertaken since the discovery of nuclear magnetic resonance is rapidly reviewed, the author describes briefly In the first chapter three types of NMR magnetometers, giving the advantages and disadvantages of each of them and deducing from this the design of the apparatus having the greatest number of qualities Chapter II is devoted to the crossed coil nuclear oscillator which operates continuously over a wide range (800 gamma). To avoid an error due to a carrying over the frequency, the measurement is carried out using bands of 1000 γ. Chapter III deals with frequency measurements. The author describes an original arrangement which makes possible the frequency-field conversion with an accuracy of ± 5 x 10 -6 , and the differential measurement between two nuclear oscillators. The report finishes with a conclusion and a few recordings. (author) [fr

  17. High transition-temperature SQUID magnetometers and practical applications

    International Nuclear Information System (INIS)

    Dantsker, E.; Lawrence Berkeley National Lab., CA

    1997-05-01

    The design, fabrication and performance of SQUID magnetometers based on thin films of the high-transition temperature superconductor YBa 2 Cu 3 O 7-x (YBCO) are described. Essential to the achieving high magnetic field resolution at low frequencies is the elimination of 1/f flux noise due to thermally activated hopping of flux vortices between pinning sites in the superconducting films. Through improvements in processing, 1/f noise in single layer YBCO thin films and YBCO-SrTiO 3 -YBCO trilayers was systematically reduced to allow fabrication of sensitive SQUID magnetometers. Both single-layer directly coupled SQUID magnetometers and multilayer magnetometers were fabricated, based on the dc SQUID with bicrystal grain boundary Josephson junctions. Multilayer magnetometers had a lower magnetic field noise for a given physical size due to greater effective sensing areas. A magnetometer consisting of a SQUID inductively coupled to the multiturn input coil of a flux transformer in a flip-chip arrangement had a field noise of 27 fT Hz -1/2 at 1 Hz and 8.5 fT Hz -1/2 at 1 kHz. A multiloop multilayer SQUID magnetometer had a field noise of 37 fT Hz -1/2 at 1 Hz and 18 fT Hz -1/2 at 1 kHz. A three-axis SQUID magnetometer for geophysical applications was constructed and operated in the field in the presence of 60 Hz and radiofrequency noise. Clinical quality magnetocardiograms were measured using multilayer SQUID magnetometers in a magnetically shielded room

  18. High transition-temperature SQUID magnetometers and practical applications

    Energy Technology Data Exchange (ETDEWEB)

    Dantsker, Eugene [Univ. of California, Berkeley, CA (United States). Dept. of Physics

    1997-05-01

    The design, fabrication and performance of SQUID magnetometers based on thin films of the high-transition temperature superconductor YBa2Cu3O7-x (YBCO) are described. Essential to the achieving high magnetic field resolution at low frequencies is the elimination of 1/f flux noise due to thermally activated hopping of flux vortices between pinning sites in the superconducting films. Through improvements in processing, 1/f noise in single layer YBCO thin films and YBCO-SrTiO3-YBCO trilayers was systematically reduced to allow fabrication of sensitive SQUID magnetometers. Both single-layer directly coupled SQUID magnetometers and multilayer magnetometers were fabricated, based on the dc SQUID with bicrystal grain boundary Josephson junctions. Multilayer magnetometers had a lower magnetic field noise for a given physical size due to greater effective sensing areas. A magnetometer consisting of a SQUID inductively coupled to the multiturn input coil of a flux transformer in a flip-chip arrangement had a field noise of 27 fT Hz-1/2 at 1 Hz and 8.5 fT Hz-1/2 at 1 kHz. A multiloop multilayer SQUID magnetometer had a field noise of 37 fT Hz-1/2 at 1 Hz and 18 fT Hz-1/2 at 1 kHz. A three-axis SQUID magnetometer for geophysical applications was constructed and operated in the field in the presence of 60 Hz and radiofrequency noise. Clinical quality magnetocardiograms were measured using multilayer SQUID magnetometers in a magnetically shielded room.

  19. Self-Compensating Excitation of Fluxgate Sensors for Space Magnetometers

    DEFF Research Database (Denmark)

    Cerman, Alec; Merayo, José M.G.; Brauer, Peter

    2008-01-01

    The paper presents design and implementation of the new self-compensating excitation circuitry to the new generation of high-precise space vector magnetometers. The application starts with complex study including design of new robust model of the non-linear inductor leading to investigation...... of the most crucial points, continuous by design of the self-compensating excitation unit and concludes with unit complex testing and application to the magnetometer. The application of the self-compensation of the excitation decreases temperature drift of the magnetometer offset caused by the temperature...

  20. Analysing harmonic motions with an iPhone’s magnetometer

    Science.gov (United States)

    Yavuz, Ahmet; Kağan Temiz, Burak

    2016-05-01

    In this paper, we propose an experiment for analysing harmonic motion using an iPhone’s (or iPad’s) magnetometer. This experiment consists of the detection of magnetic field variations obtained from an iPhone’s magnetometer sensor. A graph of harmonic motion is directly displayed on the iPhone’s screen using the Sensor Kinetics application. Data from this application was analysed with Eureqa software to establish the equation of the harmonic motion. Analyses show that the use of an iPhone’s magnetometer to analyse harmonic motion is a practical and effective method for small oscillations and frequencies less than 15-20 Hz.

  1. Motion analysis of sun salutation using magnetometer and accelerometer

    Directory of Open Access Journals (Sweden)

    Omkar S

    2009-01-01

    Full Text Available Background: Sun salutation is a part of yoga. It consists of a sequence of postures done with synchronized breathing. The practice of few cycles of sun salutation is known to help in maintaining good health and vigor. The practice of sun salutation does not need any extra gadgets. Also it is very much aerobic and invigorates the body and the mind. sun salutation, which comprises 10 postures, involves most of the joints of the body. Understanding the transition phase during motion is a challenging task, and thus, new convenient methods need to be employed. Aims: The purpose of this study was to get an insight into the motion analysis of sun salutation during the transition from each of the 10 postures. Materials and Methods: A device MicroStrain sensor 3DM-GX1, which is a combination of magnetometers, accelerometers, and gyroscopes was used to measure the inclination and the acceleration of the body along the three axes. The acceleration obtained was then separated into gravitational and kinematic components. Results and Conclusions: The value of the gravitational component helps us to understand the position of the body and the kinematic component helps us to analyze the grace of the motion.

  2. Suppression of vapor cell temperature error for spin-exchange-relaxation-free magnetometer

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Jixi, E-mail: lujixi@buaa.edu.cn; Qian, Zheng; Fang, Jiancheng; Quan, Wei [School of Instrument Science and Opto-Electronics Engineering, Beihang University, Beijing 100191 (China)

    2015-08-15

    This paper presents a method to reduce the vapor cell temperature error of the spin-exchange-relaxation-free (SERF) magnetometer. The fluctuation of cell temperature can induce variations of the optical rotation angle, resulting in a scale factor error of the SERF magnetometer. In order to suppress this error, we employ the variation of the probe beam absorption to offset the variation of the optical rotation angle. The theoretical discussion of our method indicates that the scale factor error introduced by the fluctuation of the cell temperature could be suppressed by setting the optical depth close to one. In our experiment, we adjust the probe frequency to obtain various optical depths and then measure the variation of scale factor with respect to the corresponding cell temperature changes. Our experimental results show a good agreement with our theoretical analysis. Under our experimental condition, the error has been reduced significantly compared with those when the probe wavelength is adjusted to maximize the probe signal. The cost of this method is the reduction of the scale factor of the magnetometer. However, according to our analysis, it only has minor effect on the sensitivity under proper operating parameters.

  3. Attitude Determination with Magnetometers and Accelerometers to Use in Satellite Simulator

    Directory of Open Access Journals (Sweden)

    Helio Koiti Kuga

    2013-01-01

    Full Text Available Attitude control of artificial satellites is dependent on information provided by its attitude determination process. This paper presents the implementation and tests of a fully self-contained algorithm for the attitude determination using magnetometers and accelerometers, for application on a satellite simulator based on frictionless air bearing tables. However, it is known that magnetometers and accelerometers need to be calibrated so as to allow that measurements are used to their ultimate accuracy. A calibration method is implemented which proves to be essential for improving attitude determination accuracy. For the stepwise real-time attitude determination, it was used the well-known QUEST algorithm which yields quick response with reduced computer resources. The algorithms are tested and qualified with actual data collected on the streets under controlled situations. For such street runaways, the experiment employs a solid-state magnetoresistive magnetometer and an IMU navigation block consisting of triads of accelerometers and gyros, with MEMS technology. A GPS receiver is used to record positional information. The collected measurements are processed through the developed algorithms, and comparisons are made for attitude determination using calibrated and noncalibrated data. The results show that the attitude accuracy reaches the requirements for real-time operation for satellite simulator platforms.

  4. Surface patterning with natural and synthetic polymers via an inverse electron demand Diels-Alder reaction employing microcontact chemistry.

    Science.gov (United States)

    Roling, Oliver; Mardyukov, Artur; Lamping, Sebastian; Vonhören, Benjamin; Rinnen, Stefan; Arlinghaus, Heinrich F; Studer, Armido; Ravoo, Bart Jan

    2014-10-21

    Bioorthogonal ligation methods are the focus of current research due to their versatile applications in biotechnology and materials science for post-functionalization and immobilization of biomolecules. Recently, inverse electron demand Diels-Alder (iEDDA) reactions employing 1,2,4,5-tetrazines as electron deficient dienes emerged as powerful tools in this field. We adapted iEDDA in microcontact chemistry (μCC) in order to create enhanced surface functions. μCC is a straightforward soft-lithography technique which enables fast and large area patterning with high pattern resolutions. In this work, tetrazine functionalized surfaces were reacted with carbohydrates conjugated with norbornene or cyclooctyne acting as strained electron rich dienophiles employing μCC. It was possible to create monofunctional as well as bifunctional substrates which were specifically addressable by proteins. Furthermore we structured glass supported alkene terminated self-assembled monolayers with a tetrazine conjugated atom transfer radical polymerization (ATRP) initiator enabling surface grafted polymerizations of poly(methylacrylate) brushes. The success of the surface initiated iEDDA via μCC as well as the functionalization with natural and synthetic polymers was verified via fluorescence and optical microscopy, X-ray photoelectron spectroscopy (XPS), time-of-flight secondary ion mass spectrometry (ToF-SIMS), atomic force microscopy (AFM) and attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR).

  5. Low-Fiend Vector Magnetometer (V-400-LF), Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — This 2010 NASA SBIR Phase 1 proposal for an innovative Low-Field Vector Magnetometer (V-400-LF) is a response to subtopic S1.06 Particles and Field Sensors and...

  6. Developement of a Fluxgate Magnetometer for the KITSAT-3 Satellite

    Directory of Open Access Journals (Sweden)

    S. H. Hwang

    1997-12-01

    Full Text Available The magnetometer is one of the most important payloads of scientific satellites to monitor the near-earth space environment. The electromagnetic variations of the space environment can be observed with the electric and magnetic field measurements. In practice, it is well known that the measurement of magnetic fields needs less technical complexities than that of electric fields in space. Therefore the magnetometer has long been recognized as one of the basic payloads for the scientific satellites. In this paper, we discuss the scientific fluxgate magnetometer which will be on board the KITSAT-3. The main circuit design of the present magnetometer is based on that of KISAT-1 and -2 but its facilities have been re-designed to improve the resolution to about 5nT for scientific purpose. The calibration and noise level test of this circuit have been performed at the laboratory of the Tierra Tecnica company in Japan.

  7. VOYAGER 1 SATURN MAGNETOMETER RESAMPLED DATA 9.60 SEC

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set includes Voyager 1 Saturn encounter magnetometer data that have been resampled at a 9.6 second sample rate. The data set is composed of 6 columns: 1)...

  8. VOYAGER 1 SATURN MAGNETOMETER RESAMPLED DATA 1.92 SEC

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set includes Voyager 1 Saturn encounter magnetometer data that have been resampled at a 1.92 second sample rate. The data set is composed of 6 columns: 1)...

  9. VOYAGER 1 JUPITER MAGNETOMETER RESAMPLED DATA 1.92 SEC

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set includes Voyager 1 Jupiter encounter magnetometer data that have been resampled at a 1.92 second sample rate. The data set is composed of 6 columns: 1)...

  10. VOYAGER 1 SATURN MAGNETOMETER RESAMPLED DATA 48.0 SEC

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set includes Voyager 1 Saturn encounter magnetometer data that have been resampled at a 48.0 second sample rate. The data set is composed of 6 columns: 1)...

  11. VOYAGER 1 JUPITER MAGNETOMETER RESAMPLED DATA 48.0 SEC

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set includes Voyager 1 Jupiter encounter magnetometer data that have been resampled at a 48.0 second sample rate. The data set is composed of 6 columns: 1)...

  12. VOYAGER 2 JUPITER MAGNETOMETER RESAMPLED DATA 9.60 SEC

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set includes Voyager 2 Jupiter encounter magnetometer data that have been resampled at a 9.6 second sample rate. The data set is composed of 6 columns: 1)...

  13. VOYAGER 2 SATURN MAGNETOMETER RESAMPLED DATA 1.92 SEC

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set includes Voyager 2 Saturn encounter magnetometer data that have been resampled at a 1.92 second sample rate. The data set is composed of 6 columns: 1)...

  14. VOYAGER 1 JUPITER MAGNETOMETER RESAMPLED DATA 9.60 SEC

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set includes Voyager 1 Jupiter encounter magnetometer data that have been resampled at a 9.6 second sample rate. The data set is composed of 6 columns: 1)...

  15. VOYAGER 2 SATURN MAGNETOMETER RESAMPLED DATA 48.0 SEC

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set includes Voyager 2 Saturn encounter magnetometer data that have been resampled at a 48.0 second sample rate. The data set is composed of 6 columns: 1)...

  16. VOYAGER 2 SATURN MAGNETOMETER RESAMPLED DATA 9.60 SEC

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set includes Voyager 2 Saturn encounter magnetometer data that have been resampled at a 9.6 second sample rate. The data set is composed of 6 columns: 1)...

  17. VOYAGER 2 JUPITER MAGNETOMETER RESAMPLED DATA 1.92 SEC

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set includes Voyager 2 Jupiter encounter magnetometer data that have been resampled at a 1.92 second sample rate. The data set is composed of 6 columns: 1)...

  18. Self-Calibrating Vector Helium Magnetometer (SVHM), Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — This Phase I SBIR proposal describes proposed development of a conceptual design for a Self-Calibrating Vector Helium Magnetometer (SVHM) for design and fabrication...

  19. VOYAGER 2 JUPITER MAGNETOMETER RESAMPLED DATA 48.0 SEC

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set includes Voyager 2 Jupiter encounter magnetometer data that have been resampled at a 48.0 second sample rate. The data set is composed of 6 columns: 1)...

  20. High-Range Scalar Helium Magnetometer (HSHM), Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — This SBIR Phase I proposal describes development of a conceptual design for a High-range Scalar Helium Magnetometer (HSHM) for the field range +/-16 Gauss. The HSHM...

  1. GIOTTO MAGNETOMETER 8 SECOND DATA V1.0

    Data.gov (United States)

    National Aeronautics and Space Administration — The main objective of the Giotto Magnetometer Experiment is the investigation of the interaction between Comet Halley and the solar wind at a distance of 0.9 AU from...

  2. Self-Calibrating Vector Helium Magnetometer (SVHM) Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This Phase 2 SBIR proposal describes the design, fabrication and calibration of a brass-board Self-Calibrating Vector Helium Magnetometer (SVHM). The SVHM instrument...

  3. GALILEO ORBITER JUPITER RAW MAGNETOMETER DATA V1.0

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set contains raw magnetic field data acquired by the Galileo Orbiter magnetometer at Jupiter. The data set covers the time period from 1995-11-06T00:21:30...

  4. Ultra-sensitive Magnetic Microscopy with an Atomic Magnetometer

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Young Jin [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-08-19

    The PowerPoint presentation focused on research goals, specific information about the atomic magnetometer, response and resolution factors of the SERF magnetometer, FC+AM systems, tests of field transfer and resolution on FC, gradient cancellation, testing of AM performance, ideas for a multi-channel AM, including preliminary sensitivity testing, and a description of a 6 channel DAQ system. A few ideas for future work ended the presentation.

  5. Magnetoencephalography with Optically Pumped Atomic Magnetometers

    Science.gov (United States)

    Schwindt, Peter; Colombo, Anthony; Jau, Yuan-Yu; Carter, Tony; Berry, Christopher; Young, Amber; McKay, Jim; Weisend, Michael

    2015-05-01

    We are working to develop a 36-channel array of optically pumped atomic magnetometers (AMs) to perform magnetoencephalography (MEG) with the goal of localizing magnetic sources within the human brain. The 36-channel array will consist of nine 4-channel sensor modules where the channels within each sensor will be spaced by 18 mm and each sensor will cover a 40 mm by 40 mm area of the head. In a previous 4-channel AM prototype, we demonstrated the measurement of evoked responses in both the auditory and somatosensory cortexes. This prototype had a 5 fT/Hz1/2 sensitivity. In the current version of the AM under development we are maintaining the previous sensitivity while implementing several improvements, including increasing the bandwidth from 20 Hz to more than 100 Hz, reducing the separation of the active volume of the AM from exterior of the sensor from 25 mm to 10 mm or less, and reducing the active sensor volume by a factor >10 to ~15 mm3. We will present results on the performance of our most recent AM prototype and progress toward developing a complete MEG system including a person-sized magnetic shield to provide a low-noise magnetic environment for MEG measurements.

  6. Ultrasensitive magnetometers based on rotational magnetic excitation

    International Nuclear Information System (INIS)

    Hristoforou, E.; Svec, P. Sr.

    2014-01-01

    Three new types of fluxgate magnetometers are presented in this paper, able to monitor the three components of the ambient field, all of them based on the principle of rotational excitation field. The first type is based on Yttrium- Iron Garnet (YIG) single crystal film, magnetized with rotational field on its plane, where the 2 nd , 4 th and 6 th harmonics offer the three components of the ambient field with sensitivity better than 1 pT at 0.2 Hz, its size being 25 cm 3 . The second type is based on permalloy film, where the rotational excitation field on its plane offers change of magnetoresistance with sensitivity better than 10 pT at 1 Hz, uncertainty of 1 ppm and size ∼ 8 cm 3 . The third type, is based on amorphous film, where the rotation field mode offer sensitivity better than 100 pT at 1 Hz, uncertainty of 10 ppm and size ∼ 10 mm 3 . (authors)

  7. The Search-Coil Magnetometer for MMS

    Science.gov (United States)

    Le Contel, O.; Leroy, P.; Roux, A.; Coillot, C.; Alison, D.; Bouabdellah, A.; Mirioni, L.; Meslier, L.; Galic, A.; Vassal, M. C.; Torbert, R. B.; Needell, J.; Rau, D.; Dors, I.; Ergun, R. E.; Westfall, J.; Summers, D.; Wallace, J.; Magnes, W.; Valavanoglou, A.; Olsson, G.; Chutter, M.; Macri, J.; Myers, S.; Turco, S.; Nolin, J.; Bodet, D.; Rowe, K.; Tanguy, M.; de la Porte, B.

    2016-03-01

    The tri-axial search-coil magnetometer (SCM) belongs to the FIELDS instrumentation suite on the Magnetospheric Multiscale (MMS) mission (Torbert et al. in Space Sci. Rev. (2014), this issue). It provides the three magnetic components of the waves from 1 Hz to 6 kHz in particular in the key regions of the Earth's magnetosphere namely the subsolar region and the magnetotail. Magnetospheric plasmas being collisionless, such a measurement is crucial as the electromagnetic waves are thought to provide a way to ensure the conversion from magnetic to thermal and kinetic energies allowing local or global reconfigurations of the Earth's magnetic field. The analog waveforms provided by the SCM are digitized and processed inside the digital signal processor (DSP), within the Central Electronics Box (CEB), together with the electric field data provided by the spin-plane double probe (SDP) and the axial double probe (ADP). On-board calibration signal provided by DSP allows the verification of the SCM transfer function once per orbit. Magnetic waveforms and on-board spectra computed by DSP are available at different time resolution depending on the selected mode. The SCM design is described in details as well as the different steps of the ground and in-flight calibrations.

  8. U.S. Navy Employment Options for Unmanned Surface Vehicles (USVs)

    Science.gov (United States)

    2013-01-01

    Savitz, Irv Blickstein, Peter Buryk, Robert W. Button, Paul DeLuca, James Dryden, Jason Mastbaum, Jan Osburg, Philip Padilla, Amy Potter, Carter C...VEHICLES (USVs) Scott Savitz, Irv Blickstein, Peter Buryk, Robert W. Button, Paul DeLuca, James Dryden, Jason Mastbaum, Jan Osburg, Philip Padilla, Amy...www.gdrs.com/about/profile/pdfs/UDTPacific2006_4A3_.pdf Bertram, Volker, “Unmanned Surface Vehicles: A Survey,” Brest , France: ENSIETA, 2008. As of

  9. Magnetometer and Gyroscope Calibration Method with Level Rotation

    Directory of Open Access Journals (Sweden)

    Zongkai Wu

    2018-03-01

    Full Text Available Micro electro mechanical system (MEMS gyroscopes and magnetometers are usually integrated into a sensor module or chip and widely used in a variety of applications. In existing integrated gyroscope and magnetometer calibration methods, rotation in all possible orientations is a necessary condition for a good calibration result. However, rotation around two or more axes is difficult to attain, as it is limited by the range of movement of vehicles such as cars, ships, or planes. To solve this problem, this paper proposes an integrated magnetometer and gyroscope calibration method with level rotation. The proposed method presents a redefined magnetometer output model using level attitude. New gyroscope and magnetometer calibration models are then deduced. In addition, a simplified cubature Kalman filter (CKF is established to estimate calibration parameters. This method possesses important value for application in actual systems, as it only needs level rotation for real-time calibration of gyroscopes and magnetometers. Theoretical analysis and test results verify the validity and feasibility of this method.

  10. Highly tunable hybrid metamaterials employing split-ring resonators strongly coupled to graphene surface plasmons

    Science.gov (United States)

    Liu, Peter Q.; Luxmoore, Isaac J.; Mikhailov, Sergey A.; Savostianova, Nadja A.; Valmorra, Federico; Faist, Jérôme; Nash, Geoffrey R.

    2015-01-01

    Metamaterials and plasmonics are powerful tools for unconventional manipulation and harnessing of light. Metamaterials can be engineered to possess intriguing properties lacking in natural materials, such as negative refractive index. Plasmonics offers capabilities of confining light in subwavelength dimensions and enhancing light–matter interactions. Recently, the technological potential of graphene-based plasmonics has been recognized as the latter features large tunability, higher field-confinement and lower loss compared with metal-based plasmonics. Here, we introduce hybrid structures comprising graphene plasmonic resonators coupled to conventional split-ring resonators, thus demonstrating a type of highly tunable metamaterial, where the interaction between the two resonances reaches the strong-coupling regime. Such hybrid metamaterials are employed as high-speed THz modulators, exhibiting ∼60% transmission modulation and operating speed in excess of 40 MHz. This device concept also provides a platform for exploring cavity-enhanced light–matter interactions and optical processes in graphene plasmonic structures for applications including sensing, photo-detection and nonlinear frequency generation. PMID:26584781

  11. Highly tunable hybrid metamaterials employing split-ring resonators strongly coupled to graphene surface plasmons

    Science.gov (United States)

    Liu, Peter Q.; Luxmoore, Isaac J.; Mikhailov, Sergey A.; Savostianova, Nadja A.; Valmorra, Federico; Faist, Jérôme; Nash, Geoffrey R.

    2015-11-01

    Metamaterials and plasmonics are powerful tools for unconventional manipulation and harnessing of light. Metamaterials can be engineered to possess intriguing properties lacking in natural materials, such as negative refractive index. Plasmonics offers capabilities of confining light in subwavelength dimensions and enhancing light-matter interactions. Recently, the technological potential of graphene-based plasmonics has been recognized as the latter features large tunability, higher field-confinement and lower loss compared with metal-based plasmonics. Here, we introduce hybrid structures comprising graphene plasmonic resonators coupled to conventional split-ring resonators, thus demonstrating a type of highly tunable metamaterial, where the interaction between the two resonances reaches the strong-coupling regime. Such hybrid metamaterials are employed as high-speed THz modulators, exhibiting ~60% transmission modulation and operating speed in excess of 40 MHz. This device concept also provides a platform for exploring cavity-enhanced light-matter interactions and optical processes in graphene plasmonic structures for applications including sensing, photo-detection and nonlinear frequency generation.

  12. Note: Commercial SQUID magnetometer-compatible NMR probe and its application for studying a quantum magnet

    Science.gov (United States)

    Vennemann, T.; Jeong, M.; Yoon, D.; Magrez, A.; Berger, H.; Yang, L.; Živković, I.; Babkevich, P.; Rønnow, H. M.

    2018-04-01

    We present a compact nuclear magnetic resonance (NMR) probe which is compatible with a magnet of a commercial superconducting quantum interference device magnetometer and demonstrate its application to the study of a quantum magnet. We employ trimmer chip capacitors to construct an NMR tank circuit for low temperature measurements. Using a magnetic insulator MoOPO4 with S = 1/2 (Mo5+) as an example, we show that the T-dependence of the circuit is weak enough to allow the ligand-ion NMR study of magnetic systems. Our 31P NMR results are compatible with previous bulk susceptibility and neutron scattering experiments and furthermore reveal unconventional spin dynamics.

  13. Employing response surface methodology (RSM) to improve methane production from cotton stalk.

    Science.gov (United States)

    Zhang, Han; Khalid, Habiba; Li, Wanwu; He, Yanfeng; Liu, Guangqing; Chen, Chang

    2018-03-01

    China is the largest cotton producer with the cotton output accounting for 25% of the total world's cotton production. A large quantity of cotton stalk (CS) waste is generated which is burned and causes environmental and ecological problems. This study investigated the anaerobic digestibility of CS by focusing on improving the methane yield by applying central composite design of response surface methodology (RSM). The purpose of this study was to determine the best level of factors to optimize the desired output of methane production from CS. Thus, it was necessary to describe the relationship of many individual variables with one or more response values for the effective utilization of CS. The influences of feed to inoculum (F/I) ratio and organic loading (OL) on methane production were investigated. Results showed that the experimental methane yield (EMY) and volatile solid (VS) removal were calculated to be 70.22 mL/gVS and 14.33% at F/I ratio of 0.79 and organic loading of 25.61 gVS/L, respectively. Characteristics of final effluent showed that the anaerobic system was stable. This research laid a foundation for future application of CS to alleviate the problems of waste pollution and energy output.

  14. Development of Autonomous Magnetometer Rotorcraft For Wide Area Assessment

    Energy Technology Data Exchange (ETDEWEB)

    Mark D. McKay; Matthew O. Anderson

    2011-08-01

    Large areas across the United States and internationally are potentially contaminated with unexploded ordinance (UXO), with some ranges encompassing tens to hundreds of thousands of acres. Technologies are needed which will allow for cost effective wide area scanning with (1) near 100% coverage and (2) near 100% detection of subsurface ordnance or features indicative of subsurface ordnance. The current approach to wide area assessment is a multi-level one, in which medium - altitude fixed wing optical imaging is used for an initial site assessment. This assessment is followed with low altitude manned helicopter based magnetometry. Subsequent to this wide area assessment targeted surface investigations are performed using either towed geophysical sensor arrays or man portable sensors. In order to be an effective tool for small UXO detection, the sensing altitude for magnetic site investigations needs to be on the order of 1 to 3 meters. These altitude requirements mean that manned helicopter surveys will generally only be feasible in large, open and relatively flat terrains. While such surveys are effective in mapping large areas relatively fast there are substantial mobilization/demobilization, staffing and equipment costs associated with these surveys, resulting in costs of approximately $100-$150/acre. In addition, due to the low altitude there are substantial risks to pilots and equipment. Surface towed arrays provide highresolution maps but have other limitations, e.g. in their ability to navigate rough terrain effectively. Thus there is a need for other systems, which can be used for effective data collection. An Unmanned Aerial Vehicle (UAV) magnetometer platform is an obvious alternative. The motivation behind such a system is that it reduces risk to operators, is lower in initial and Operational and Maintenance (O&M) costs (and can thus potentially be applied to smaller sites) and has the potential of being more effective in terms of detection and possibly

  15. A multichannel double relaxation oscillation SQUID magnetometer system for magnetoencephalogram

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Chan Seok [Biomagnetism Research Center, Korea Research Institute of Standards and Science, Yuseong, Daejeon 305-600 (Korea); Department of Applied Physics, Korea University, 208 Seochang-dong, Jochiwon, Chungnam 339-800 (Korea); Lee, Yong-Ho; Kwon, Hyukchan; Kim, Jin-Mok; Kim, Kiwoong; Park, Yong-Ki [Biomagnetism Research Center, Korea Research Institute of Standards and Science, Yuseong, Daejeon 305-600 (Korea); Lee, Soon Gul [Department of Applied Physics, Korea University, 208 Seochang-dong, Jochiwon, Chungnam 339-800 (Korea)

    2004-06-01

    We developed multichannel SQUID magnetometer and gradiometer systems based on double relaxation oscillation SQUIDs (DROS) for use in biomagnetic studies, such as magnetoencephalogram (MEG). DROS consists of two SQUIDs (signal SQUID and reference SQUID) in series, and a relaxation circuit of an inductor and a resistor. Specially, we used single reference junction instead of the reference SQUID. Since DROS magnetometer has about 10 times lager flux-to-voltage transfer coefficient than dc SQUID, we can use simple flux-locked loop electronics for SQUID operation. The measured noise at 100 Hz was 3 fT/{radical}(Hz) for the magnetometer and 4 fT/{radical}(Hz) for the planar gradiometer, which are low enough for neuromagnetic measurements. We also constructed two kinds of multichannel SQUID systems, 40-channel and 37-channel system. Using this system, we measured several MEG signals. (copyright 2004 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  16. Lunar physical properties from analysis of magnetometer data

    Science.gov (United States)

    Daily, W. D.

    1979-01-01

    The electromagnetic properties of the lunar interior are discussed with emphasis on (1) bulk, crustal, and local anomalous conductivity; (2) bulk magnetic permeability measurements, iron abundance estimates, and core size limits; (3) lunar ionosphere and atmosphere; and (4) crustal magnetic remanence: scale size measurements and constraints on remanence origin. Appendices treat the phase relationship between the energetic particle flux modulation and current disc penetrations in the Jovian magnetosphere (Pioneer 10 inbound) theories for the origin of lunar magnetism; electrical conductivity anomalies associated with circular lunar maria; electromagnetic properties of the Moon; Mare Serenitatis conductivity anomaly detected by Apollo 16 and Lunokhod 2 magnetometers; and lunar properties from magnetometer data: effects of data errors.

  17. Three-axis atomic magnetometer based on spin precession modulation

    Energy Technology Data Exchange (ETDEWEB)

    Huang, H. C.; Dong, H. F., E-mail: hfdong@buaa.edu.cn; Hu, X. Y.; Chen, L.; Gao, Y. [School of Instrumentation Science and Opto-Electronics Engineering, Beihang University, Beijing 100191 (China)

    2015-11-02

    We demonstrate a three-axis atomic magnetometer with one intensity-modulated pump beam and one orthogonal probe beam. The main field component is measured using the resonance of the pumping light, while the transverse field components are measured simultaneously using the optical rotation of the probe beam modulated by the spin precession. It is an all-optical magnetometer without using any modulation field or radio frequency field. Magnetic field sensitivity of 0.8 pT/Hz{sup 1∕2} is achieved under a bias field of 2 μT.

  18. Improved molecular fingerprint analysis employing multi-branched gold nanoparticles in conjunction with surface-enhanced Raman scattering

    Directory of Open Access Journals (Sweden)

    Johnston J

    2015-12-01

    Full Text Available Jencilin Johnston,1 Erik N Taylor,1,2 Richard J Gilbert,2 Thomas J Webster1,3 1Department of Chemical Engineering, 2Department of Chemistry and Chemical Biology, Northeastern University, Boston, MA, USA; 3Center of Excellence for Advanced Materials Research, King Abdulaziz University, Jeddah, Saudi Arabia Abstract: Vibrational spectroscopy is a powerful analytical tool that assesses molecular properties based on spectroscopic signatures. In this study, the effect of gold nanoparticle morphology (spherical vs multi-branched was assessed for the characterization of a Raman signal (ie, molecular fingerprint that may be helpful for numerous medical applications. Multi-branched gold nanoparticles (MBAuNPs were fabricated using a green chemistry method which employed the reduction of gold ion solute by 2-[4-(2-hydroxyethyl-1-piperazyl] ethane sulfonic acid. Two types of reporter dyes, indocyanine (IR820 and IR792 and carbocyanine (DTTC [3,3'-diethylthiatricarbocyanine iodide] and DTDC [3,3'-diethylthiadicarbocyanine iodide], were functionalized to the surface of the MBAuNPs and stabilized with denatured bovine serum albumin, thus forming the surface-enhanced Raman spectroscopy tag. Fluorescein isothiocyanate-conjugated anti-epidermal growth factor receptor to the surface-enhanced Raman spectroscopy tags and the properties of the resulting conjugates were assessed through determination of the Raman signal. Using the MBAuNP Raman probes synthesized in this manner, we demonstrated that MBAuNP provided significantly more surface-enhanced Raman scattering signal when compared with the associated spherical gold nanoparticle of similar size and concentration. MBAuNP enhancements were retained in the surface-enhanced Raman spectroscopy tags complexed to anti-epidermal growth factor receptor, providing evidence that this could be a useful biological probe for enhanced Raman molecular fingerprinting. Furthermore, while utilizing IR820 as a novel reporter dye

  19. Ionospheric travelling convection vortices observed by the Greenland magnetometer chain

    DEFF Research Database (Denmark)

    Kotsiaros, Stavros; Stolle, Claudia; Friis-Christensen, Eigil

    2013-01-01

    The Greenland magnetometer array continuously provides geomagnetic variometer data since the early eighties. With the polar cusp passing over it almost every day, the array is suitable to detect ionospheric traveling convection vortices (TCVs), which were rst detected by Friis-Christensen et al...

  20. Circuit of automatic modulating field control for nuclear magnetometer

    International Nuclear Information System (INIS)

    Ivashkevich, S.A.

    1996-01-01

    A circuit is suggested for automatic adjustment of the modulation amplitude of the magnetic field to be measured for nuclear magnetometers, and necessary range of this adjustment is determined. Depending on the measured field inhomogeneity, the circuit can smoothly vary the modulating field amplitude approximately by a factor of 30 stabilizing it at an optimal level. 5 refs., 1 fig

  1. Small Fluxgate Magnetometers: Development and Future Trends in Spain

    Directory of Open Access Journals (Sweden)

    Lucas Pérez

    2010-03-01

    Full Text Available In this paper, we give an overview of the research on fluxgate magnetometers carried out in Spain. In particular we focus in the development of the planar-type instruments. We summarize the fabrication processes and signal processing developments as well as their use in complex systems and space.

  2. Small Fluxgate Magnetometers: Development and Future Trends in Spain

    Science.gov (United States)

    Ciudad, David; Díaz-Michelena, Marina; Pérez, Lucas; Aroca, Claudio

    2010-01-01

    In this paper, we give an overview of the research on fluxgate magnetometers carried out in Spain. In particular we focus in the development of the planar-type instruments. We summarize the fabrication processes and signal processing developments as well as their use in complex systems and space. PMID:22294904

  3. On the Viability of Magnetometer-Based Projectile Orientation Measurements

    Science.gov (United States)

    2007-11-01

    1820 by Hans Christian Oersted . If any of these sources were to be close enough to a projectile-borne magne- tometer, the local magnetic field would...Harkins, T. Using Magnetometers for Roll Position Determination in a Spinning Projectile Control System: Theory and Flight Test Results; ARL-TR-3142; U.S

  4. Adaption of the Magnetometer Towed Array geophysical system to meet Department of Energy needs for hazardous waste site characterization

    International Nuclear Information System (INIS)

    Cochran, J.R.; McDonald, J.R.; Russell, R.J.; Robertson, R.; Hensel, E.

    1995-10-01

    This report documents US Department of Energy (DOE)-funded activities that have adapted the US Navy's Surface Towed Ordnance Locator System (STOLS) to meet DOE needs for a ''... better, faster, safer and cheaper ...'' system for characterizing inactive hazardous waste sites. These activities were undertaken by Sandia National Laboratories (Sandia), the Naval Research Laboratory, Geo-Centers Inc., New Mexico State University and others under the title of the Magnetometer Towed Array (MTA)

  5. Applications of modern high-precision Overhauser magnetometers

    Science.gov (United States)

    Narkhov, E. D.; Muravyev, L. A.; Sergeev, A. V.; Fedorov, A. L.; Denisov, A. Yu.; Shirokov, A. A.; Sapunov, V. A.

    2017-09-01

    Increased sensitivity and resolution of geophysical instruments significantly enhances the effectiveness of non- destructive investigation methods for standard geological problems and allows new experiments. We suggest to use modern highly sensitive scalar magnetometers for identification and study of geological and artificial low-contrast objects in a magnetic field. We present application results of a modern nuclear precession magnetometer POS based on the processor Overhauser sensor. The device is developed and produced by the Quantum Magnetometry Laboratory, Ural Federal University, Yekaterinburg, Russia. Experiments conducted in the laboratory and observatories allowed to determine the device absolute accuracy of 0.5 nT and sensitivity of 0.02 nT, and to confirm its operability in large magnetic field gradients. This sensitivity is sufficient for detection of magnetic field changes caused, for example, by tectonomagnetic, seismomagnetic, piezomagnetic effects and electrokinetic phenomena in the geological environment. We conducted field experiments comparing POS magnetometers metrological characteristics with similar instruments from Scintrex and Geometrics. The results confirm measurement high stability in long-term observations of the magnetic field change due to geodynamic processes. We tested POS instruments in various geophysical applications, including prospecting and exploration of minerals (placer and ore gold, hydrocarbons, kimberlites); identification of ferromagnetic objects in cover environments; archaeological sites mapping. Our latest experience adds to this list a magnetic survey for pipeline inspection purposes. In addition, we discuss application of a novel absolute 3-component magnetometer POS-4 based on a principle of bias field switching method. The device was tested at several INTERMAGNET geomagnetic observatories. Due to high absolute accuracy and stability, there is a good prospect of implementing these magnetometers at observation

  6. A theoretical and experimental investigation of the proton magnetometer

    International Nuclear Information System (INIS)

    Hancke, G.P.

    1987-01-01

    This study comprises the investigation of the properties of the proton magnetometer based on the free precession of protons. The basic principle of the free precession of protons in the earth's magnetic field is described and the most important factors affecting this free precession are examined. It is shown that very important parameters to keep in mind are the polarization time and the magnitude of the polarization field. A discussion of the errors of a proton magnetometer built on the periodometer principles is given and it is shown that the error in counting of the number of precession periods during the time of measurement contributes most to the total error. The magnitude of this error depends on the signal-to-noise ratio, the instability of the operating threshold of the discriminator of the period counter, it's operating time and the tuning accuracy of the sensor to the precession frequency. The penetration to a magnetometer input of variable magnetic and electric interferences, their influence on the phase of the useful signal, and the resulting measurement errors are examined and methods of reducing the effects of interferences are discussed. The optimization of sensor design is very important in the development of proton magnetometers. The coil geometry, physical size, the working substance and the polarization design are important parameters. The selection of a method for processing the precession signal of a proton magnetometer is examined, given a sensor and signal amplifier with fixed parameters. A method is proposed and compared with known methods. Measurement errors are computed for various signal-to-noise ratios and times of observation of the precession signal, and it is shown that the proposed method is superior to conventional methods found in commercial instruments

  7. Feasibility Study for an Autonomous UAV -Magnetometer System -- Final Report on SERDP SEED 1509:2206

    Energy Technology Data Exchange (ETDEWEB)

    Roelof Versteeg; Mark McKay; Matt Anderson; Ross Johnson; Bob Selfridge; Jay Bennett

    2007-09-01

    Large areas across the United States are potentially contaminated with UXO, with some ranges encompassing tens to hundreds of thousands of acres. Technologies are needed which will allow for cost effective wide area scanning with 1) near 100 % coverage and 2) near 100 % detection of subsurface ordnance or features indicative of subsurface ordnance. The current approach to wide area scanning is a multi-level one, in which medium altitude fixed wing optical imaging is used for an initial site assessment. This assessment is followed with low altitude manned helicopter based magnetometry followed by surface investigations using either towed geophysical sensor arrays or man portable sensors. In order to be effective for small UXO detection, the sensing altitude for magnetic site investigations needs to be on the order of 1 – 3 meters. These altitude requirements means that manned helicopter surveys will generally only be feasible in large, open and relatively flat terrains. While such surveys are effective in mapping large areas relatively fast there are substantial mobilization/demobilization, staffing and equipment costs associated with these surveys (resulting in costs of approximately $100-$150/acre). Surface towed arrays provide high resolution maps but have other limitations, e.g. in their ability to navigate rough terrain effectively. Thus, other systems are needed allowing for effective data collection. An UAV (Unmanned Aerial Vehicle) magnetometer platform is an obvious alternative. The motivation behind such a system is that it would be safer for the operators, cheaper in initial and O&M costs, and more effective in terms of site characterization. However, while UAV data acquisition from fixed wing platforms for large (> 200 feet) stand off distances is relatively straight forward, a host of challenges exist for low stand-off distance (~ 6 feet) UAV geophysical data acquisition. The objective of SERDP SEED 1509:2006 was to identify the primary challenges

  8. Plasma Distribution in Mercury's Magnetosphere Derived from MESSENGER Magnetometer and Fast Imaging Plasma Spectrometer Observations

    Science.gov (United States)

    Korth, Haje; Anderson, Brian J.; Gershman, Daniel J.; Raines, Jim M.; Slavin, James A.; Zurbuchen, Thomas H.; Solomon, Sean C.; McNutt, Ralph L.

    2014-01-01

    We assess the statistical spatial distribution of plasma in Mercury's magnetosphere from observations of magnetic pressure deficits and plasma characteristics by the MErcury Surface, Space ENvironment, GEochemistry, and Ranging (MESSENGER) spacecraft. The statistical distributions of proton flux and pressure were derived from 10months of Fast Imaging Plasma Spectrometer (FIPS) observations obtained during the orbital phase of the MESSENGER mission. The Magnetometer-derived pressure distributions compare favorably with those deduced from the FIPS observations at locations where depressions in the magnetic field associated with the presence of enhanced plasma pressures are discernible in the Magnetometer data. The magnitudes of the magnetic pressure deficit and the plasma pressure agree on average, although the two measures of plasma pressure may deviate for individual events by as much as a factor of approximately 3. The FIPS distributions provide better statistics in regions where the plasma is more tenuous and reveal an enhanced plasma population near the magnetopause flanks resulting from direct entry of magnetosheath plasma into the low-latitude boundary layer of the magnetosphere. The plasma observations also exhibit a pronounced north-south asymmetry on the nightside, with markedly lower fluxes at low altitudes in the northern hemisphere than at higher altitudes in the south on the same field line. This asymmetry is consistent with particle loss to the southern hemisphere surface during bounce motion in Mercury's offset dipole magnetic field.

  9. Machine Learning Based Localization and Classification with Atomic Magnetometers

    Science.gov (United States)

    Deans, Cameron; Griffin, Lewis D.; Marmugi, Luca; Renzoni, Ferruccio

    2018-01-01

    We demonstrate identification of position, material, orientation, and shape of objects imaged by a Rb 85 atomic magnetometer performing electromagnetic induction imaging supported by machine learning. Machine learning maximizes the information extracted from the images created by the magnetometer, demonstrating the use of hidden data. Localization 2.6 times better than the spatial resolution of the imaging system and successful classification up to 97% are obtained. This circumvents the need of solving the inverse problem and demonstrates the extension of machine learning to diffusive systems, such as low-frequency electrodynamics in media. Automated collection of task-relevant information from quantum-based electromagnetic imaging will have a relevant impact from biomedicine to security.

  10. Combined alternating gradient force magnetometer and susceptometer system

    International Nuclear Information System (INIS)

    Pérez, M.; Mendizábal Vázquez, I. de; Aroca, C.; Ranchal, R.; Cobos, P.

    2015-01-01

    We report the design, fabrication, and characterization of a new system that combines the performances of two different types of magnetic characterization systems, Alternating Gradient Force Magnetometers (AGFM) and susceptometers. The flexibility of our system is demonstrated by its capability to be used as any of them, AGFM or susceptometer, without any modification in the experimental set-up because of the electronics we have developed. Our system has a limit of sensitivity lower than 5 × 10 −7 emu. Moreover, its main advantage is demonstrated by the possibility of measuring small quantities of materials under DC or AC magnetic fields that cannot properly be measured with a commercial vibrating sample magnetometers or AGFM

  11. Three-dimensional analysis of magnetometer array data

    Science.gov (United States)

    Richmond, A. D.; Baumjohann, W.

    1984-01-01

    A technique is developed for mapping magnetic variation fields in three dimensions using data from an array of magnetometers, based on the theory of optimal linear estimation. The technique is applied to data from the Scandinavian Magnetometer Array. Estimates of the spatial power spectra for the internal and external magnetic variations are derived, which in turn provide estimates of the spatial autocorrelation functions of the three magnetic variation components. Statistical errors involved in mapping the external and internal fields are quantified and displayed over the mapping region. Examples of field mapping and of separation into external and internal components are presented. A comparison between the three-dimensional field separation and a two-dimensional separation from a single chain of stations shows that significant differences can arise in the inferred internal component.

  12. Combined alternating gradient force magnetometer and susceptometer system

    Energy Technology Data Exchange (ETDEWEB)

    Pérez, M.; Mendizábal Vázquez, I. de; Aroca, C. [Dpto. Física Aplicada, E.T.S.I. Telecomunicación, Universidad Politécnica de Madrid, Ciudad Universitaria s/n, Madrid 28040 (Spain); Ranchal, R. [Dpto. Física de Materiales, Facultad Ciencias Físicas, Universidad Complutense de Madrid, Ciudad Universitaria s/n, Madrid 28040 (Spain); Cobos, P. [ISOM, Universidad Politécnica de Madrid, Ciudad Universitaria s/n, Madrid 28040 (Spain)

    2015-01-15

    We report the design, fabrication, and characterization of a new system that combines the performances of two different types of magnetic characterization systems, Alternating Gradient Force Magnetometers (AGFM) and susceptometers. The flexibility of our system is demonstrated by its capability to be used as any of them, AGFM or susceptometer, without any modification in the experimental set-up because of the electronics we have developed. Our system has a limit of sensitivity lower than 5 × 10{sup −7} emu. Moreover, its main advantage is demonstrated by the possibility of measuring small quantities of materials under DC or AC magnetic fields that cannot properly be measured with a commercial vibrating sample magnetometers or AGFM.

  13. The Upgraded CARISMA Magnetometer Array in the THEMIS Era

    Science.gov (United States)

    Mann, I. R.; Milling, D. K.; Rae, I. J.; Ozeke, L. G.; Kale, A.; Kale, Z. C.; Murphy, K. R.; Parent, A.; Usanova, M.; Pahud, D. M.; Lee, E.-A.; Amalraj, V.; Wallis, D. D.; Angelopoulos, V.; Glassmeier, K.-H.; Russell, C. T.; Auster, H.-U.; Singer, H. J.

    2008-12-01

    This review describes the infrastructure and capabilities of the expanded and upgraded Canadian Array for Realtime InvestigationS of Magnetic Activity (CARISMA) magnetometer array in the era of the THEMIS mission. Formerly operated as the Canadian Auroral Network for the OPEN Program Unified Study (CANOPUS) magnetometer array until 2003, CARISMA capabilities have been extended with the deployment of additional fluxgate magnetometer stations (to a total of 28), the upgrading of the fluxgate magnetometer cadence to a standard data product of 1 sample/s (raw sampled 8 samples/s data stream available on request), and the deployment of a new network of 8 pairs of induction coils (100 samples per second). CARISMA data, GPS-timed and backed up at remote field stations, is collected using Very Small Aperture Terminal (VSAT) satellite internet in real-time providing a real-time monitor for magnetic activity on a continent-wide scale. Operating under the magnetic footprint of the THEMIS probes, data from 5 CARISMA stations at 29-30 samples/s also forms part of the formal THEMIS ground-based observatory (GBO) data-stream. In addition to technical details, in this review we also outline some of the scientific capabilities of the CARISMA array for addressing all three of the scientific objectives of the THEMIS mission, namely: 1. Onset and evolution of the macroscale substorm instability, 2. Production of storm-time MeV electrons, and 3. Control of the solar wind-magnetosphere coupling by the bow shock, magnetosheath, and magnetopause. We further discuss some of the compelling questions related to these three THEMIS mission science objectives which can be addressed with CARISMA.

  14. Fiber Optic Magnetometers Using Planar And Cylindrical Magnetostrictive Transducers

    Science.gov (United States)

    Bucholtz, F.; Yurek, A. M.; Koo, K. P.; Dandridge, A.

    1987-04-01

    Fiber optic magnetometers which require high sensitivity at low frequencies (dc-10 Hz) rely on the nonlinear magnetostriction of materials such as amorphous metallic glass alloys. Typically, fiber is bonded to a magnetostrictive sample to convert strain in the sample to phase shift in a fiber interferometer. We present the results of measurements of the frequency dependence and dc and ac magnetic field sensitivity of both planar and cylindrical transducing elements, and discuss the practical advantages and disadvan-tages of each configuration.

  15. All-optical, Three-axis Fiber Laser Magnetometer

    Science.gov (United States)

    2012-04-16

    force acting on a current carrying bridge in the presence of a magnetic field, which drives its oscillation measured with a fiber laser strain sensor... strain between two cores as a function of rotation for difference inclinations and (b) reported inclination vs. actual inclination for a bend angle of...such as those based on SQUIDS, giant magnetoresistance (GMR), scalar resonance magnetometers, and flux-gates; however, a fiber optic sensor enables

  16. Athermal fiber laser for the SWARM absolute scalar magnetometer

    Science.gov (United States)

    Fourcault, W.; Léger, J.-M.; Costes, V.; Fratter, I.; Mondin, L.

    2017-11-01

    The Absolute Scalar Magnetometer (ASM) developed by CEA-LETI/CNES is an optically pumped 4He magnetic field sensor based on the Zeeman effect and an electronic magnetic resonance whose effects are amplified by a laser pumping process [1-2]. Consequently, the role of the laser is to pump the 4He atoms at the D0 transition as well as to allow the magnetic resonance signal detection. The ASM will be the scalar magnetic reference instrument of the three ESA Swarm satellites to be launched in 2012 in order to carry out the best ever survey of the Earth magnetic field and its temporal evolution. The sensitivity and accuracy of this magnetometer based on 4He optical pumping depend directly on the characteristics of its light source, which is the key sub-system of the sensor. We describe in this paper the selected fiber laser architecture and its wavelength stabilization scheme. Its main performance in terms of spectral emission, optical power at 1083 nm and intensity noise characteristics in the frequency bands used for the operation of the magnetometer, are then presented. Environmental testing results (thermal vacuum cycling, vibrations, shocks and ageing) are also reported at the end of this paper.

  17. Swarm Optimization-Based Magnetometer Calibration for Personal Handheld Devices

    Science.gov (United States)

    Ali, Abdelrahman; Siddharth, Siddharth; Syed, Zainab; El-Sheimy, Naser

    2012-01-01

    Inertial Navigation Systems (INS) consist of accelerometers, gyroscopes and a processor that generates position and orientation solutions by integrating the specific forces and rotation rates. In addition to the accelerometers and gyroscopes, magnetometers can be used to derive the user heading based on Earth's magnetic field. Unfortunately, the measurements of the magnetic field obtained with low cost sensors are usually corrupted by several errors, including manufacturing defects and external electro-magnetic fields. Consequently, proper calibration of the magnetometer is required to achieve high accuracy heading measurements. In this paper, a Particle Swarm Optimization (PSO)-based calibration algorithm is presented to estimate the values of the bias and scale factor of low cost magnetometers. The main advantage of this technique is the use of the artificial intelligence which does not need any error modeling or awareness of the nonlinearity. Furthermore, the proposed algorithm can help in the development of Pedestrian Navigation Devices (PNDs) when combined with inertial sensors and GPS/Wi-Fi for indoor navigation and Location Based Services (LBS) applications.

  18. Swarm Optimization-Based Magnetometer Calibration for Personal Handheld Devices

    Directory of Open Access Journals (Sweden)

    Naser El-Sheimy

    2012-09-01

    Full Text Available Inertial Navigation Systems (INS consist of accelerometers, gyroscopes and a processor that generates position and orientation solutions by integrating the specific forces and rotation rates. In addition to the accelerometers and gyroscopes, magnetometers can be used to derive the user heading based on Earth’s magnetic field. Unfortunately, the measurements of the magnetic field obtained with low cost sensors are usually corrupted by several errors, including manufacturing defects and external electro-magnetic fields. Consequently, proper calibration of the magnetometer is required to achieve high accuracy heading measurements. In this paper, a Particle Swarm Optimization (PSO-based calibration algorithm is presented to estimate the values of the bias and scale factor of low cost magnetometers. The main advantage of this technique is the use of the artificial intelligence which does not need any error modeling or awareness of the nonlinearity. Furthermore, the proposed algorithm can help in the development of Pedestrian Navigation Devices (PNDs when combined with inertial sensors and GPS/Wi-Fi for indoor navigation and Location Based Services (LBS applications.

  19. Detection Range of Airborne Magnetometers in Magnetic Anomaly Detection

    Directory of Open Access Journals (Sweden)

    Chengjing Li

    2015-11-01

    Full Text Available Airborne magnetometers are utilized for the small-range search, precise positioning, and identification of the ferromagnetic properties of underwater targets. As an important performance parameter of sensors, the detection range of airborne magnetometers is commonly set as a fixed value in references regardless of the influences of environment noise, target magnetic properties, and platform features in a classical model to detect airborne magnetic anomalies. As a consequence, deviation in detection ability analysis is observed. In this study, a novel detection range model is proposed on the basis of classic detection range models of airborne magnetometers. In this model, probability distribution is applied, and the magnetic properties of targets and the environment noise properties of a moving submarine are considered. The detection range model is also constructed by considering the distribution of the moving submarine during detection. A cell-averaging greatest-of-constant false alarm rate test method is also used to calculate the detection range of the model at a desired false alarm rate. The detection range model is then used to establish typical submarine search probabilistic models. Results show that the model can be used to evaluate not only the effects of ambient magnetic noise but also the moving and geomagnetic features of the target and airborne detection platform. The model can also be utilized to display the actual operating range of sensor systems.

  20. A modular, extendible and field-tolerant multichannel vector magnetometer based on current sensor SQUIDs

    Science.gov (United States)

    Storm, J.-H.; Drung, D.; Burghoff, M.; Körber, R.

    2016-09-01

    We present the prototype module of our extendible and robust multichannel SQUID magnetometer system. A large multi-module arrangement can be implemented by using up to 7 modules. The system is intended for high-precision measurements of biomagnetism and spin precession. Further demanding applications are magnetorelaxometry and ultra-low-field nuclear magnetic resonance (ULF NMR), where pulsed magnetic fields of up to 100 mT are typically applied. The system is operated inside the Berlin magnetically shielded room (BMSR-2) and equipped with 18 magnetometers consisting of niobium (Nb) wire-wound pick-up coils. A total of 16 small pick-up coils with 17.1 mm diameter form a regular grid with individual channels arranged to ensure system sensitivity covers all three orthogonal spatial directions. Two large hexagonal pick-up coils with an equivalent diameter of 74.5 mm sensitive in z-direction surround the grid at two different heights and are suitable for the detection of deep sources. Each pick-up coil is connected to the input of a thin-film Nb SQUID current sensor via a detachable superconducting contact. The SQUIDs are equipped with integrated input current limiters. Feedback into the pick-up coils is employed to minimise crosstalk between channels. The current sensor chip package includes a superconducting shield of Nb. The field distortion of the prototype and a multi-module arrangement was analysed by numerical simulation. The measured noise of the small magnetometers was between 0.6 and 1.5 fT {{Hz}}-1/2, and well below 1 fT {{Hz}}-1/2 for the large ones. Using a software gradiometer, we achieved a minimum noise level of 0.54 fT {{Hz}}-1/2. We performed ULF NMR experiments, verifying the system’s robustness against pulsed fields, and magnetoencephalographgy (MEG) on somatosensory evoked neuronal activity. The low noise performance of our 18-channel prototype enabled the detection of high-frequency components at around 1 kHz by MEG.

  1. New Magneto-Inductive DC Magnetometer for Space Missions

    Science.gov (United States)

    Moldwin, M.; Bronner, B.; Regoli, L.; Thoma, J.; Shen, A.; Jenkins, G.; Cutler, J.

    2017-12-01

    A new magneto-inductive DC magnetometer is being developed at the University of Michigan that provides fluxgate quality measurements in a low mass, volume, power and cost package. The magnetometer enables constellation-class missions not only due to its low-resource requirements, but also its potential for commercial integrated circuit fabrication. The magneto-inductive operating principle is based on a simple resistance-inductor (RL) circuit and involves measurement of the time it takes to charge and discharge the inductor between an upper and lower threshold by means of a Schmitt trigger oscillator. This time is proportional to the inductance that in turn is proportional to the field strength. We have modeled the operating principle in the circuit simulator SPICE and have built a proto-type using modified commercial sensors. The performance specifications include a dynamic range over the full-Earth's field, sampling rates up to 80 Hz, sensor and electronics mass of about 30 g, circuit board and sensor housing volume of < 100 cm3, and power consumption of about 5 mW. This system's noise levels are predicted to be about 100 pT /√Hz @ 1 Hz with a precision of about 100 pT. Due to the simple circuit design, lack of an analog-to-digital converter, and choice of oscillator, we anticipate that it will be extremely temperature stable and radiation tolerant. This presentation will describe the constellation mission enabling design, the development status and the testing results of this new magnetometer.

  2. Miniature scientific-grade induction magnetometer for cubesats

    Science.gov (United States)

    Pronenko, Vira

    2017-04-01

    One of the main areas of space research is the study and forecasting of space weather. The society is more and more depending nowadays on satellite technology and communications, so it is vital to understand the physical process in the solar-terrestrial system which may disturb them. Besides the solar radiation and Space Weather effects, the Earth's ionosphere is also modified by the ever increasing industrial activity. There have been also multiple reports relating VLF and ELF wave activity to atmospheric storms and geological processes, such as earthquakes and volcanic activity. For advancing in these fields, the AC magnetic field permanent monitoring is crucial. Using the cubesat technology would allow increasing the number of measuring points dramatically. It is necessary to mention that the cubesats use for scientific research requires the miniaturization of scientific sensors what is a serious problem because the reduction of their dimensions leads, as a rule, to the parameters degradation, especially of sensitivity threshold. Today, there is no basic model of a sensitive miniature induction magnetometer. Even the smallest one of the known - for the Bepi-Colombo mission to Mercury - is too big for cubesats. The goal of the present report is to introduce the new design of miniature three-component sensor for measurement of alternative vector magnetic fields - induction magnetometer (IM). The study directions were concentrated on the ways and possibilities to create the miniature magnetometer with best combination of parameters. For this a set of scientific and technological problems, mostly aimed at the sensor construction improvement, was solved. The most important parameter characterizing magnetometer quality is its own magnetic noise level (NL). The analysis of the NL influencing factors is made and the ways to decrease it are discussed in the report. Finally, the LEMI-151 IM was developed for the SEAM cubesat mission with optimal performances within the

  3. Magnetometer probe with low temperature rotation and optical fibers

    Energy Technology Data Exchange (ETDEWEB)

    Pajerowski, D M; Meisel, M W [Department of Physics and the National High Magnetic Field Laboratory, University of Florida, Gainesville, Florida 32611-8440 (United States)], E-mail: meisel@phys.ufl.edu

    2009-02-01

    A new probe has been developed that allows for both optical irradiation and uniaxial rotation, all in the low temperature environment of a commercial superconducting quantum interference device (SQUID) magnetometer. As part of the design process, various materials were investigated and characterized for their low temperature structural and magnetic properties, including nylon, Vespel, Delrin, Spiderwire monofilament, and PowerPro braided microfilament. Using this information, a prototype was built and operated. Characteristics of the probe will be presented along with a summary of the low temperature (T {>=} 2 K) and high magnetic field (H {<=} 7 T) properties of the construction materials.

  4. Magnetometer probe with low temperature rotation and optical fibers

    Science.gov (United States)

    Pajerowski, D. M.; Meisel, M. W.

    2009-02-01

    A new probe has been developed that allows for both optical irradiation and uniaxial rotation, all in the low temperature environment of a commercial superconducting quantum interference device (SQUID) magnetometer. As part of the design process, various materials were investigated and characterized for their low temperature structural and magnetic properties, including nylon, Vespel, Delrin, Spiderwire monofilament, and PowerPro braided microfilament. Using this information, a prototype was built and operated. Characteristics of the probe will be presented along with a summary of the low temperature (T >= 2 K) and high magnetic field (H <= 7 T) properties of the construction materials.

  5. Three axis vector atomic magnetometer utilizing polarimetric technique

    Energy Technology Data Exchange (ETDEWEB)

    Pradhan, Swarupananda, E-mail: spradhan@barc.gov.in, E-mail: pradhans75@gmail.com [Laser and Plasma Technology Division, Bhabha Atomic Research Centre, Mumbai 400085, India and Homi Bhabha National Institute, Department of Atomic Energy, Mumbai 400094 (India)

    2016-09-15

    The three axis vector magnetic field measurement based on the interaction of a single elliptically polarized light beam with an atomic system is described. The magnetic field direction dependent atomic responses are extracted by the polarimetric detection in combination with laser frequency modulation and magnetic field modulation techniques. The magnetometer geometry offers additional critical requirements like compact size and large dynamic range for space application. Further, the three axis magnetic field is measured using only the reflected signal (one polarization component) from the polarimeter and thus can be easily expanded to make spatial array of detectors and/or high sensitivity field gradient measurement as required for biomedical application.

  6. Effect of mobility devices on orientation sensors that contain magnetometers.

    Science.gov (United States)

    Kendell, Cynthia; Lemaire, Edward D

    2009-01-01

    Orientation sensors containing magnetometers use the earth's magnetic field as a reference. Ferromagnetic objects may distort this magnetic field, leading to inaccurate orientation output. We explored the viability of these orientation sensors for motion analysis in an assistive mobility device rehabilitative setting. We attached two MTx orientation sensors (XSens; Enschade, the Netherlands), connected to the XBus Master data collection unit (XSens), to a plastic frame such that the relative angle between sensors was constant. We then moved a series of mobility devices in proximity to the plastic frame: two knee-ankle-foot orthoses (aluminum, stainless steel), one ankle-foot orthosis, two transtibial prostheses (exoskeletal, endoskeletal), two walkers (standard, Challenger Low Wide [Evolution Technologies; Port Coquitlam, Canada]), and two wheelchairs (Tango [OrthoFab; Quebec City, Canada], GTi [Quickie; Phoenix, Arizona]). For each mobility device, we calculated the average difference in relative angle between the baseline and peak angles for each of five trials. Errors ranged from less than 0.10 to 35.29 degrees, depending on the mobility device and frame positioning near the device. This demonstrated the large errors that can occur when magnetometer-based orientation sensors with mobility devices are used. While strategic orientation sensor placement on some mobility devices can minimize these errors to an acceptable level, testing protocols should be implemented to verify orientation sensor accuracy for these applications.

  7. The absolute magnetometers on board Swarm, lessons learned from more than two years in space

    DEFF Research Database (Denmark)

    Hulot, Gauthier; Leger, Jean-Michel; Vigneron, Pierre

    ESA's Swarm satellites carry 4He absolute magnetometers (ASM), designed by CEA-Léti and developed in partnership with CNES. These instruments are the first-ever space-borne magnetometers to use a common sensor to simultaneously deliver 1Hz independent absolute scalar and vector readings of the ma...

  8. Quantum dynamical study of the O(1D)+HCl reaction employing three electronic state potential energy surfaces

    Science.gov (United States)

    Yang, Huan; Han, Ke-Li; Nanbu, Shinkoh; Nakamura, Hiroki; Balint-Kurti, Gabriel G.; Zhang, Hong; Smith, Sean C.; Hankel, Marlies

    2008-01-01

    Quantum dynamical calculations are reported for the title reaction, for both product arrangement channels and using potential energy surfaces corresponding to the three electronic states, 1A'1, 2A'1, and 1A″1, which correlate with both reactants and products. The calculations have been performed for J =0 using the time-dependent real wavepacket approach by Gray and Balint-Kurti [J. Chem. Phys. 108, 950 (1998)]. Reaction probabilities for both product arrangement channels on all three potential energy surfaces are presented for total energies between 0.1 and 1.1eV. Product vibrational state distributions at two total energies, 0.522 and 0.722eV, are also presented for both channels and all three electronic states. Product rotational quantum state distributions are presented for both product arrangement channels and all three electronic states for the first six product vibrational states.

  9. A 20-channel magnetoencephalography system based on optically pumped magnetometers

    Science.gov (United States)

    Borna, Amir; Carter, Tony R.; Goldberg, Josh D.; Colombo, Anthony P.; Jau, Yuan-Yu; Berry, Christopher; McKay, Jim; Stephen, Julia; Weisend, Michael; Schwindt, Peter D. D.

    2017-12-01

    We describe a multichannel magnetoencephalography (MEG) system that uses optically pumped magnetometers (OPMs) to sense the magnetic fields of the human brain. The system consists of an array of 20 OPM channels conforming to the human subject’s head, a person-sized magnetic shield containing the array and the human subject, a laser system to drive the OPM array, and various control and data acquisition systems. We conducted two MEG experiments: auditory evoked magnetic field and somatosensory evoked magnetic field, on three healthy male subjects, using both our OPM array and a 306-channel Elekta-Neuromag superconducting quantum interference device (SQUID) MEG system. The described OPM array measures the tangential components of the magnetic field as opposed to the radial component measured by most SQUID-based MEG systems. Herein, we compare the results of the OPM- and SQUID-based MEG systems on the auditory and somatosensory data recorded in the same individuals on both systems.

  10. Compact Atomic Magnetometer for Global Navigation (NAV-CAM)

    Science.gov (United States)

    Bulatowicz, Michael; Larsen, Michael

    2014-05-01

    Northrop Grumman Navigation Systems Division is developing an atom-based magnetometer technology that has the potential for providing a global position reference independent of GPS. The NAV-CAM sensor is a direct outgrowth of the Nuclear Magnetic Resonance Gyro under development by the same technical team. It will be the only known magnetic field sensor capable of providing all 3 axes of magnetic vector direction and magnitude simultaneously with a whole-field scalar measurement, all within a single multi-axis sensing element measuring 4mm cube or smaller, essentially eliminating many of the problems encountered when using physically separate sensors or sensing elements. According to information presented by Ariyur et al. at the 2010 American Control Conference [1], the anticipated accuracy of 10 pico-Tesla (pT) and precision of <0.5 pT of the NAV-CAM sensor will enable magnetic determination of position with 20 meter accuracy and 1 meter resolution.

  11. Associating ground magnetometer observations with current or voltage generators

    DEFF Research Database (Denmark)

    Hartinger, M. D.; Xu, Z.; Clauer, C. R.

    2017-01-01

    A circuit analogy for magnetosphere-ionosphere current systems has two extremes for driversof ionospheric currents: ionospheric elec tric fields/voltages constant while current/conductivity vary—the“voltage generator”—and current constant while electric field/conductivity vary—the “current generator.......”Statistical studies of ground magnetometer observations associated with dayside Transient High LatitudeCurrent Systems (THLCS) driven by similar mechanisms find contradictory results using this paradigm:some studies associate THLCS with voltage generators, others with current generators. We argue that mostof...... these two assumptions substantially alter expectations for magnetic perturbations associatedwith either a current or a voltage generator. Our results demonstrate that before interpreting groundmagnetometer observations of THLCS in the context of current/voltage generators, the location...

  12. The Search-coil Magnetometer for the THOR mission

    Science.gov (United States)

    Sahraoui, Fouad; Jannet, Guillaume; Pinçon, Jean-louis; Mansour, Malik; Chalumeau, Gilles; Chabassière, Michel; Hachemi, Tedjani; Jeandet, Alexis; Henri, Pierre; Le Contel, Olivier; Rezeau, Laurence

    2017-04-01

    Turbulence Heating ObserveR (THOR) is the first mission ever flown in space that is fully dedicated to plasma turbulence. The search-coil magnetometer (SCM) of THOR is a triaxial dual-band antenna dedicated to measuring the magnetic field fluctuations in the frequency range [1Hz,4kHz] and [1,200]kHz. THOR/SCM has a long heritage from earlier space missions such as Cluster, Themis, MMS, BepiColombo, Taranis, Solar orbiter and Solar Probe. In comparison to those missions, the SCM of THOR has a higher sensitivity level, which makes it capable of measuring very low amplitude magnetic fluctuations, in particular in the solar wind. Those measurements are crucial to address the problem of turbulence and energy dissipation at electron scales, a central goal of the THOR mission.

  13. Magnetometer-Augmented IMU Simulator: In-Depth Elaboration

    Directory of Open Access Journals (Sweden)

    Thomas Brunner

    2015-03-01

    Full Text Available The location of objects is a growing research topic due, for instance, to the expansion of civil drones or intelligent vehicles. This expansion was made possible through the development of microelectromechanical systems (MEMS, inexpensive and miniaturized inertial sensors. In this context, this article describes the development of a new simulator which generates sensor measurements, giving a specific input trajectory. This will allow the comparison of pose estimation algorithms. To develop this simulator, the measurement equations of every type of sensor have to be analytically determined. To achieve this objective, classical kinematic equations are used for the more common sensors, i.e., accelerometers and rate gyroscopes. As nowadays, the MEMS inertial measurement units (IMUs are generally magnetometer-augmented, an absolute world magnetic model is implemented. After the determination of the perfect measurement (through the error-free sensor models, realistic error models are developed to simulate real IMU behavior. Finally, the developed simulator is subjected to different validation tests.

  14. Magnetometer-augmented IMU simulator: in-depth elaboration.

    Science.gov (United States)

    Brunner, Thomas; Lauffenburger, Jean-Philippe; Changey, Sébastien; Basset, Michel

    2015-03-04

    The location of objects is a growing research topic due, for instance, to the expansion of civil drones or intelligent vehicles. This expansion was made possible through the development of microelectromechanical systems (MEMS), inexpensive and miniaturized inertial sensors. In this context, this article describes the development of a new simulator which generates sensor measurements, giving a specific input trajectory. This will allow the comparison of pose estimation algorithms. To develop this simulator, the measurement equations of every type of sensor have to be analytically determined. To achieve this objective, classical kinematic equations are used for the more common sensors, i.e., accelerometers and rate gyroscopes. As nowadays, the MEMS inertial measurement units (IMUs) are generally magnetometer-augmented, an absolute world magnetic model is implemented. After the determination of the perfect measurement (through the error-free sensor models), realistic error models are developed to simulate real IMU behavior. Finally, the developed simulator is subjected to different validation tests.

  15. Miniaturized digital fluxgate magnetometer for small spacecraft applications

    International Nuclear Information System (INIS)

    Forslund, Åke; Ivchenko, Nickolay; Olsson, Göran; Edberg, Terry; Belyayev, Serhiy; Marusenkov, Andriy

    2008-01-01

    A novel design of an Earth field digital fluxgate magnetometer is presented, the small magnetometer in low-mass experiment (SMILE). The combination of a number of new techniques results in significant miniaturization of both sensor and electronics. The design uses a sensor with volume compensation, combining three dual rod cores in a Macor® cube with the side dimension of 20 mm. Use of volume compensation provides high geometrical stability of the axes and improved performance compared to component compensated sensors. The sensor is operated at an excitation frequency of 8 kHz. Most of the instrument functionality is combined in a digital signal processing core, implemented in a field programmable gate array (FPGA). The pick-up signal is digitized after amplification and filtering, and values of compensation currents for each of the axes are determined by a digital correlation algorithm, equivalent to a matched filter, and are fed to a hybrid pulse-width modulation/delta-sigma digital-to-analogue converter driving the currents through the compensation coils. Using digital design makes the instrument very flexible, reduces power consumption and opens possibilities for the customization of the operation modes. The current implementation of the design is based on commercial off-the-shelf components. A calibration of the SMILE instrument was carried out at the Nurmijärvi Geophysical Observatory, showing high linearity (within 6 nT on the whole ±50 µT scale), good orthogonality (22 arcmin) and very good temperature stability of the axes

  16. The maize tapetum employs diverse mechanisms to synthesize and store proteins and flavonoids and transfer them to the pollen surface.

    Science.gov (United States)

    Li, Yubing; Suen, Der Fen; Huang, Chien-Yu; Kung, Shung-Yee; Huang, Anthony H C

    2012-04-01

    In anthers, the tapetum synthesizes and stores proteins and flavonoids, which will be transferred to the surface of adjacent microspores. The mechanism of synthesis, storage, and transfer of these pollen-coat materials in maize (Zea mays) differs completely from that reported in Arabidopsis (Arabidopsis thaliana), which stores major pollen-coat materials in tapetosomes and elaioplasts. On maize pollen, three proteins, glucanase, xylanase, and a novel protease, Zea mays pollen coat protease (ZmPCP), are predominant. During anther development, glucanase and xylanase transcripts appeared at a mid developmental stage, whereas protease transcript emerged at a late developmental stage. Protease and xylanase transcripts were present only in the anther tapetum of the plant, whereas glucanase transcript was distributed ubiquitously. ZmPCP belongs to the cysteine protease family but has no closely related paralogs. Its nascent polypeptide has a putative amino-terminal endoplasmic reticulum (ER)-targeting peptide and a propeptide. All three proteins were synthesized in the tapetum and were present on mature pollen after tapetum death. Electron microscopy of tapetum cells of mid to late developmental stages revealed small vacuoles distributed throughout the cytoplasm and numerous secretory vesicles concentrated near the locular side. Immunofluorescence microscopy and subcellular fractionation localized glucanase in ER-derived vesicles in the cytoplasm and the wall facing the locule, xylanase in the cytosol, protease in vacuoles, and flavonoids in subdomains of ER rather than in vacuoles. The nonoverlapping subcellular locations of the three proteins and flavonoids indicate distinct modes of their storage in tapetum cells and transfer to the pollen surface, which in turn reflect their respective functions in tapetum cells or the pollen surface.

  17. Development of Magnetometer Digital Circuit for KSR-3 Rocket and Analytical Study on Calibration Result

    Directory of Open Access Journals (Sweden)

    Eun-Seok Lee

    2002-12-01

    Full Text Available This paper describes the re-design and the calibration results of the MAG digital circuit onboard the KSR-3. We enhanced the sampling rate of magnetometer data. Also, we reduced noise and increased authoritativeness of data. We could confirm that AIM resolution was decreased less than 1nT of analog calibration by a digital calibration of magnetometer. Therefore, we used numerical-program to correct this problem. As a result, we could calculate correction and error of data. These corrections will be applied to magnetometer data after the launch of KSR-3.

  18. Swarm's absolute magnetometer experimental vector mode, an innovative capability for space magnetometry

    DEFF Research Database (Denmark)

    Hulot, Gauthier; Vigneron, Pierre; Leger, Jean-Michel

    2015-01-01

    ESA's Swarm satellites carry a new generation of 4He absolute magnetometers (ASM), designed by CEA-Leti and developed in partnership with CNES. These instruments are the rst-ever space-born magnetometers to use a common sensor to simultaneously deliver 1Hz independent absolute scalar and vector...... be monitored from space with such absolute vector magnetometers....... readings of the magnetic eld. Since launch, these ASMs provided very high accuracy scalar eld data, as nominally required for the mission, together with experimental vector eld data. Here, we compare geomagnetic eld models built from such ASM-only data with models built from the mission's nominal 1Hz data...

  19. Employing Response Surface Methodology for the Optimization of Ultrasound Assisted Extraction of Lutein and β-Carotene from Spinach

    Directory of Open Access Journals (Sweden)

    Ammar Altemimi

    2015-04-01

    Full Text Available The extraction of lutein and β-carotene from spinach (Spinacia oleracea L. leaves is important to the dietary supplement industry. A Box-Behnken design and response surface methodology (RSM were used to investigate the effect of process variables on the ultrasound-assisted extraction (UAE of lutein and β-carotene from spinach. Three independent variables, extraction temperature (°C, extraction power (% and extraction time (min were studied. Thin-layer chromatography (TLC followed by UV visualization and densitometry was used as a simple and rapid method for both identification and quantification of lutein and β-carotene during UAE. Methanol extracts of leaves from spinach and authentic standards of lutein and β-carotene were separated by normal-phase TLC with ethyl acetate-acetone (5:4 (v/v as the mobile phase. In this study, the combination of TLC, densitometry, and Box–Behnken with RSM methods were effective for the quantitative analysis of lutein and β-carotene from spinach extracts. The resulting quadratic polynomial models for optimizing lutein and β-carotene from spinach had high coefficients of determination of 0.96 and 0.94, respectively. The optimal UAE settings for output of lutein and β-carotene simultaneously from spinach extracts were an extraction temperature of 40 °C, extraction power of 40% (28 W/cm3 and extraction time of 16 min. The identity and purity of each TLC spot was measured using time-of-flight mass spectrometry. Therefore, UAE assisted extraction of carotenes from spinach can provide a source of lutein and β-carotene for the dietary supplement industry.

  20. The possibility of using magnetometers for surveying archaeological sites around power lines

    Czech Academy of Sciences Publication Activity Database

    Křivánek, Roman

    Issue 49, January (2017), s. 3-7 ISSN N Institutional support: RVO:67985912 Keywords : geophysical prospection * non-destructive archaeology * magnetometer survey * electricity disturbations Subject RIV: AC - Archeology, Anthropology, Ethnology

  1. IceBridge Scintrex CS-3 Cesium Magnetometer L0 Raw Magnetic Field

    Data.gov (United States)

    National Aeronautics and Space Administration — The NASA IceBridge Scintrex CS-3 Cesium Magnetometer L0 Raw Magnetic Field data set contains magnetic field readings and fluxgate values taken over Greenland using...

  2. Basic technical parameters of magnetometers with ferromagnetic transducers and a method to define them

    International Nuclear Information System (INIS)

    Nagiello, Z.

    1980-01-01

    The basic technical parameters of magnetometers with ferromagnetic transducers and measuring methods to define these parameters have been discussed. Special attention was paid to factors which essentially affect the inaccuracy of these measuring instruments. (author)

  3. Simplified High-Performance Roll Out Composite Magnetometer Boom, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — In response to NASA's need for compact, low-cost deployable magnetometer booms for CubeSats, Roccor proposes to develop a Simple High-performance Roll-Out Composite...

  4. Measuring In-Flight Angular Motion With a Low-Cost Magnetometer

    National Research Council Canada - National Science Library

    Harkins, Thomas E; Wilson, Michael J

    2007-01-01

    A technique for obtaining pitch, yaw, and roll rates of a projectile from a single, low-cost, commercial off-the-shelf magnetometer has been developed at the Advanced Munitions Concepts Branch of the U.S...

  5. IceBridge Flux Gate Magnetometer L0 Raw Magnetic Field

    Data.gov (United States)

    National Aeronautics and Space Administration — The NASA IceBridge Flux Gate Magnetometer L0 Raw Magnetic Field (IMFGM0) data set contains magnetic field readings taken over Antarctica using the Integrity...

  6. IceBridge Geometrics 823A Cesium Magnetometer L0 Raw Magnetic Field

    Data.gov (United States)

    National Aeronautics and Space Administration — The NASA IceBridge Geometrics 823A Cesium Magnetometer L0 Raw Magnetic Field (IMGEO0) data set contains magnetic field readings taken over Antarctica using the...

  7. Rad-Hard Sigma-Delta 3-Channel ADC for Fluxgate Magnetometers, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — The measurement of the magnetic field vector is of fundamental importance to space physics missions. The fluxgate magnetometer is a device developed for precise...

  8. Sensitivity optimization of Bell-Bloom magnetometers by manipulation of atomic spin synchronization

    Science.gov (United States)

    Ranjbaran, M.; Tehranchi, M. M.; Hamidi, S. M.; Khalkhali, S. M. H.

    2018-05-01

    Many efforts have been devoted to the developments of atomic magnetometers for achieving the high sensitivity required in biomagnetic applications. To reach the high sensitivity, many types of atomic magnetometers have been introduced for optimization of the creation and relaxation rates of atomic spin polarization. In this paper, regards to sensitivity optimization techniques in the Mx configuration, we have proposed a novelty approach for synchronization of the spin precession in the Bell-Bloom magnetometers. We have utilized the phenomenological Bloch equations to simulate the spin dynamics when modulation of pumping light and radio frequency magnetic field were both used for atomic spin synchronization. Our results showed that the synchronization process, improved the magnetometer sensitivity respect to the classical configurations.

  9. IceBridge Geometrics 823A Cesium Magnetometer L2 Geolocated Magnetic Anomalies

    Data.gov (United States)

    National Aeronautics and Space Administration — The NASA IceBridge Geometrics 823A Cesium Magnetometer L2 Geolocated Magnetic Anomalies (IMGEO2) data set contains magnetic anomaly measurements taken over...

  10. IceBridge Flux Gate Magnetometer L0 Raw Magnetic Field, Version 1

    Data.gov (United States)

    National Aeronautics and Space Administration — The NASA IceBridge Flux Gate Magnetometer L0 Raw Magnetic Field (IMFGM0) data set contains magnetic field readings taken over Antarctica using the Integrity...

  11. IceBridge Geometrics 823A Cesium Magnetometer L1B Time-Tagged Magnetic Field

    Data.gov (United States)

    National Aeronautics and Space Administration — The NASA IceBridge Geometrics 823A Cesium Magnetometer L1B Time-Tagged Magnetic Field (IMGEO1B) data set contains magnetic field strength measurements taken over...

  12. IceBridge Scintrex CS-3 Cesium Magnetometer L1B Geolocated Magnetic Anomalies, Version 1

    Data.gov (United States)

    National Aeronautics and Space Administration — The NASA IceBridge Scintrex CS-3 Cesium Magnetometer L1B Geolocated Magnetic Anomalies (IMCS31B) data set contains magnetic field readings taken over Greenland using...

  13. IceBridge Scintrex CS-3 Cesium Magnetometer L0 Raw Magnetic Field, Version 1

    Data.gov (United States)

    National Aeronautics and Space Administration — The NASA IceBridge Scintrex CS-3 Cesium Magnetometer L0 Raw Magnetic Field data set contains magnetic field readings and fluxgate values taken over Greenland using...

  14. IceBridge Scintrex CS-3 Cesium Magnetometer L1B Geolocated Magnetic Anomalies

    Data.gov (United States)

    National Aeronautics and Space Administration — The NASA IceBridge Scintrex CS-3 Cesium Magnetometer L1B Geolocated Magnetic Anomalies (IMCS31B) data set contains magnetic field readings taken over Antarctica...

  15. CubeSat Attitude Determination via Kalman Filtering of Magnetometer and Solar Cell Data

    OpenAIRE

    Babcock, Erik

    2011-01-01

    Attitude determination options are limited on a CubeSat due to power, mass, and volume constraints. This report documents the design and implementation of an extended Kalman filter (EKF) for attitude estimation using three-axis magnetometer and two-axis solar cell measurements. The motivation for such a system is to utilize sensors already present on most CubeSats, namely three-axis magnetometers for active magnetic detumbling and four faces of solar cell arrays for power generation. The syst...

  16. Integration of a MEMS Inertial Measuring Unit with a MEMS Magnetometer for 3D Orientation Estimation

    DEFF Research Database (Denmark)

    Cai, Junping; Malureanu, Christian; Andersen, Niels Lervad

    2011-01-01

    This paper presents an algorithm for combining the measurements of a MEMS Inertial Measurement Unit (IMU) and a MEMS magnetometer. The measurements are done using a special designed and customized miniature detecting system for 3D orientation estimation, and position tracking......This paper presents an algorithm for combining the measurements of a MEMS Inertial Measurement Unit (IMU) and a MEMS magnetometer. The measurements are done using a special designed and customized miniature detecting system for 3D orientation estimation, and position tracking...

  17. A xylophone bar magnetometer for micro/pico satellites

    Science.gov (United States)

    Lamy, Hervé; Niyonzima, Innocent; Rochus, Pierre; Rochus, Véronique

    2010-10-01

    The Belgian Institute of Space Aeronomy (BIRA-IASB), "Centre Spatial de Liège" (CSL), "Laboratoire de Techniques Aéronautiques et Spatiales" (LTAS) of University of Liège, and the Microwave Laboratory of University of Louvain-La-Neuve (UCL) are collaborating in order to develop a miniature version of a xylophone bar magnetometer (XBM) using Microelectromechanical Systems (MEMS) technology. The device is based on a classical resonating xylophone bar. A sinusoidal current is supplied to the bar oscillating at the fundamental transverse resonant mode of the bar. When an external magnetic field is present, the resulting Lorentz force causes the bar to vibrate at its fundamental frequency with an amplitude directly proportional to the vertical component of the ambient magnetic field. In this paper we illustrate the working principles of the XBM and the challenges to reach the required sensitivity in space applications (measuring magnetic fields with an accuracy of approximately of 0.1 nT). The optimal dimensions of the MEMS XBM are discussed as well as the constraints on the current flowing through the bar. Analytical calculations as well as simulations with finite element methods have been used. Prototypes have been built in the Microwave Laboratory using silicon on insulator (SOI) and bulk micromachining processes. Several methods to accurately measure the displacement of the bar are proposed.

  18. Ground pulsation magnetometer observations conjugated with relativistic electron precipitation

    Science.gov (United States)

    Yahnin, A. G.; Yahnina, T. A.; Raita, T.; Manninen, J.

    2017-09-01

    In this report, we investigate the role of electromagnetic ion cyclotron (EMIC) waves in production of relativistic electron precipitation (REP). Over a thousand REP events were detected from four NOAA Polar-orbiting Operational Environmental Satellites in July-December 2005. Of these, a total of 112 events were conjugated with a ground-based network of six Finnish induction coil magnetometers and one in Lovozero observatory at Kola Peninsula, Russia. The observation of geomagnetic pulsations during the conjugated events showed that about one third of them were accompanied by pulsations in the Pc1 range, which are the signature of EMIC waves. In fact, the sources of some of these EMIC waves were well outside the location of the REP event. This means that in such cases the REP events were not originated from scattering by EMIC waves. Finally, it is concluded that for this limited set of conjugated events only a quarter might be related to scattering by EMIC waves. The majority of the events are not correlated with EMIC wave signatures in ground-based observations; they were associated with either no pulsations or noise-like pulsations PiB and PiC.

  19. The low cost Proton Precession Magnetometer developed at the Indian Institute of Geomagnetism

    Science.gov (United States)

    Mahavarkar, P.; Singh, S.; Labde, S.; Dongre, V.; Patil, A.

    2017-05-01

    Proton magnetometers are the oldest scalar magnetometers. The first commercial units were produced in early 1960s as portable instruments. In continuation airborne instruments appeared with optimized speed of readings and sensitivity, large sensors etc. Later development of Overhauser and optically pumped magnetometers has eliminated Proton magnetometers from airborne surveys. However they remain very popular in various ground surveys and observatories. With this primary purpose of generating the ground based magnetic data, the Indian Institute of Geomagnetism (IIG) for the last 3 decades have been developing low cost Proton Precession Magnetometers (PPM). Beginning with the 1 nT PPM which has undergone several changes in design, the successor PM7 the advanced version has been successfully developed by the institute and is installed at various observatories of the institute. PM7 records the total field `F' with accuracy of 0.1 nT and a sampling rate of 10 seconds/sample. This article briefly discusses the design and development of this IIG make PM7 and compares the data recorded by this instrument with one of the commercially available Overhauser magnetometer in the world market. The quality of data recorded by PM7 is in excellent agreement with the Overhauser. With the available quality of data generated by this instrument, PM7 is an affordable PPM for scientific institutions, schools and colleges intending to carry out geomagnetic studies. The commercial cost of PM7 is ≈ 20% of the cost of Overhauser available in market.

  20. The low cost Proton Precession Magnetometer developed at the Indian Institute of Geomagnetism

    International Nuclear Information System (INIS)

    Mahavarkar, P.; Singh, S.; Labde, S.; Dongre, V.; Patil, A.

    2017-01-01

    Proton magnetometers are the oldest scalar magnetometers. The first commercial units were produced in early 1960s as portable instruments. In continuation airborne instruments appeared with optimized speed of readings and sensitivity, large sensors etc. Later development of Overhauser and optically pumped magnetometers has eliminated Proton magnetometers from airborne surveys. However they remain very popular in various ground surveys and observatories. With this primary purpose of generating the ground based magnetic data, the Indian Institute of Geomagnetism (IIG) for the last 3 decades have been developing low cost Proton Precession Magnetometers (PPM). Beginning with the 1 nT PPM which has undergone several changes in design, the successor PM7 the advanced version has been successfully developed by the institute and is installed at various observatories of the institute. PM7 records the total field 'F' with accuracy of 0.1 nT and a sampling rate of 10 seconds/sample. This article briefly discusses the design and development of this IIG make PM7 and compares the data recorded by this instrument with one of the commercially available Overhauser magnetometer in the world market. The quality of data recorded by PM7 is in excellent agreement with the Overhauser. With the available quality of data generated by this instrument, PM7 is an affordable PPM for scientific institutions, schools and colleges intending to carry out geomagnetic studies. The commercial cost of PM7 is ≈ 20% of the cost of Overhauser available in market.

  1. A Reduced SWAP+C DC Magnetometer for Geomagnetic and Space Physics Research

    Science.gov (United States)

    Moldwin, M.; Ojeda, L.; Rogacki, S.; Pelloni, M.; Regoli, L.

    2016-12-01

    A new small, low mass, low power consumption, and low cost (reduced SWaP+C or Size, Weight and Power + Cost) magnetometer is being developed for both ground-based and future CubeSat Constellation-class missions. The University of Michigan (UM) magnetometer is based on the PNI Induction magnetometer electronics. PNI 3100 magnetometers have flight heritage on Cubesat Missions (e.g., the UM RAXs mission), but they were used primarily for attitude control. This presentation describes the modifications and performance of the magnetometer and our strategies for continued improvement in performance and its environmental testing. A description of further development of this new magnetometer with regards to its ability to measure geophysical signals up to 10 Hz is also given. Current performance has noise levels of about 1 nT/root Hz at 1 Hz, temperature stability, inherent radiation tolerance, in a 3 x 5 cm package (electronics and sensors), draws 10s of mW and costs a few hundred dollars. We will also present several strategies to reduce the noise by a factor of 5-10 that are currently being pursued.

  2. A portable Hall magnetometer probe for characterization of magnetic iron oxide nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Araujo, Jefferson F.D.F.; Costa, Mateus C.; Louro, Sonia R.W.; Bruno, Antonio C., E-mail: acbruno@puc-rio.br

    2017-03-15

    We have built a portable Hall magnetometer probe, for measuring magnetic properties of iron oxide nanoparticles, that can be used for bulk materials and liquid samples as well. The magnetometer probe consists of four voltage-programmable commercial Hall sensors and a thin acrylic plate for positioning the sensors. In order to operate, it needs to be attached to a pole of an electromagnet and connected to an AD converter and a computer. It acquires a complete magnetization curve in a couple of minutes and has a magnetic moment sensitivity of 3.5×10{sup −7} Am{sup 2}. We tested its performance with magnetic nanoparticles containing an iron oxide core and having coating layers with different sizes. The magnetization results obtained were compared with measurements performed on commercial stand-alone magnetometers, and exhibited errors of about ±0.2 Am{sup 2}/kg (i.e 0.4%) at saturation and below 0.5 Am{sup 2}/kg (i.e. 10%) at remanence. - Highlights: • A low-cost portable Hall magnetometer probe has been built. • The Hall magnetometer probe can be attached to any electromagnet. • The Hall probe was calibrated and successfully compared to industry standard magnetometers. • The Hall probe was able to measure iron oxide nanoparticles with different coatings.

  3. Quantum Tunneling in Testosterone 6β-Hydroxylation by Cytochrome P450: Reaction Dynamics Calculations Employing Multiconfiguration Molecular-Mechanical Potential Energy Surfaces

    Science.gov (United States)

    Zhang, Yan; Lin, Hai

    2009-05-01

    Testosterone hydroxylation is a prototypical reaction of human cytochrome P450 3A4, which metabolizes about 50% of oral drugs on the market. Reaction dynamics calculations were carried out for the testosterone 6β-hydrogen abstraction and the 6β-d1-testosterone 6β-duterium abstraction employing a model that consists of the substrate and the active oxidant compound I. The calculations were performed at the level of canonical variational transition state theory with multidimensional tunneling and were based on a semiglobal full-dimensional potential energy surface generated by the multiconfiguration molecular mechanics technique. The tunneling coefficients were found to be around 3, indicating substantial contributions by quantum tunneling. However, the tunneling made only modest contributions to the kinetic isotope effects. The kinetic isotope effects were computed to be about 2 in the doublet spin state and about 5 in the quartet spin state.

  4. Employer branding

    OpenAIRE

    Mičková, Kateřina

    2008-01-01

    The demand for qualified employees is higher then the offering, both in Czech republic and internationally. Demand for specific skills, in addition to a greater demand for workforce generally, is making employee recruitment and retention much more difficult and expensive. Employer Branding claims to be an answer to this new challenge. This international concept focuses on developing an "employer brand" - mental image of a company as an employer. To achieve this, it is necessary to demonstrate...

  5. Industry Employment

    Science.gov (United States)

    Occupational Outlook Quarterly, 2012

    2012-01-01

    This article illustrates projected employment change by industry and industry sector over 2010-20 decade. Workers are grouped into an industry according to the type of good produced or service provided by the establishment for which they work. Industry employment projections are shown in terms of numeric change (growth or decline in the total…

  6. Quantifying the In-Flight Yaw, Pitch, and Roll of a Semi-Rigidly Mounted Potassium Vapour Magnetometer Suspended Under a Heavy-Lift Multi-Rotor UAV and its Impact on Data Quality

    Science.gov (United States)

    Walter, C. A.; Braun, A.; Fotopoulos, G.

    2017-12-01

    Research is being conducted to develop an Unmanned Aerial System (UAS) that is capable of reliably and efficiently collecting high resolution, industry standard magnetic data (magnetic data with a fourth difference of +/- 0.05 nT) via an optically pumped vapour magnetometer. The benefits of developing a UAS with these capabilities include improvements in the resolution of localized airborne surveys (2.5 km by 2.5 km) and the ability to conduct 3D magnetic gradiometry surveys in the observation gap evident between traditional terrestrial and manned airborne magnetic surveys (surface elevation up to 120 m). Quantifying the extent of an optically pumped vapour magnetometer's 3D orientation variations, while in-flight and suspended under a UAS, is a significant advancement to existing knowledge as optically pumped magnetometers have an orientation-dependent (to the primary magnetic field vector) process for measuring the magnetic field. This study investigates the orientation characteristics of a GEM Systems potassium vapour magnetometer, GSMP-35U, while semi-rigidly suspended 3 m under a DJI S900, heavy-lift multi-rotor UAV (Unmanned Aerial Vehicle) during an airborne surveying campaign conducted Northeast of Thunder Bay, Ontario, Canada. A nine degrees of freedom IMU (Inertial Measurement Unit), the Adafruit GY-80, was used to quantify the 3D orientation variations (yaw, pitch and roll) of the magnetic sensor during flight. The orientation and magnetic datasets were indexed and linked with a date and time stamp (within 1 ms) via a Raspberry Pi 2, acting as an on-board computer and data storage system. Analysing the two datasets allowed for the in-flight orientation variations of the potassium vapour magnetometer to be directly compared with the gathered magnetic and signal quality data of the magnetometer. The in-flight orientation characteristics of the magnetometer were also quantified for a range of air-speeds and flight maneuvers throughout the survey. Overall

  7. VIA Employability

    DEFF Research Database (Denmark)

    Andersen, Henrik Mariendal

    2017-01-01

    The fact that students develop employability during their education is a key point for educational institutions and the focus on this issue has never been greater. This project looks into personal experience from VIA-graduates of "developing their employability" during the education and how it......’s realized at the entrance to the labor market and in the future career. The purpose is to find opportunities to improve employability-developing activities and to adapt it to specific needs from the students. Based on a number of qualitative interviews and personality tests of the graduates, an increased...... personal approach is proposed in the agenda of employability. And ensure a wide range of offers, that appeal to multiple and differentiated personal and professional approaches to employability....

  8. The effect of winding and core support material on the thermal gain dependence of a fluxgate magnetometer sensor

    Science.gov (United States)

    Miles, David M.; Mann, Ian R.; Kale, Andy; Milling, David K.; Narod, Barry B.; Bennest, John R.; Barona, David; Unsworth, Martyn J.

    2017-10-01

    Fluxgate magnetometers are an important tool in geophysics and space physics but are typically sensitive to variations in sensor temperature. Changes in instrumental gain with temperature, thermal gain dependence, are thought to be predominantly due to changes in the geometry of the wire coils that sense the magnetic field and/or provide magnetic feedback. Scientific fluxgate magnetometers typically employ some form of temperature compensation and support and constrain wire sense coils with bobbins constructed from materials such as MACOR machinable ceramic (Corning Inc.) which are selected for their ultra-low thermal deformation rather than for robustness, cost, or ease of manufacturing. We present laboratory results comparing the performance of six geometrically and electrically matched fluxgate sensors in which the material used to support the windings and for the base of the sensor is varied. We use a novel, low-cost thermal calibration procedure based on a controlled sinusoidal magnetic source and quantitative spectral analysis to measure the thermal gain dependence of fluxgate magnetometer sensors at the ppm°C-1 level in a typical magnetically noisy university laboratory environment. We compare the thermal gain dependence of sensors built from MACOR, polyetheretherketone (PEEK) engineering plastic (virgin, 30 % glass filled and 30 % carbon filled), and acetal to examine the trade between the thermal properties of the material, the impact on the thermal gain dependence of the fluxgate, and the cost and ease of manufacture. We find that thermal gain dependence of the sensor varies as one half of the material properties of the bobbin supporting the wire sense coils rather than being directly related as has been historically thought. An experimental sensor constructed from 30 % glass-filled PEEK (21.6 ppm°C-1) had a thermal gain dependence within 5 ppm°C-1 of a traditional sensor constructed from MACOR ceramic (8.1 ppm°C-1). If a modest increase in thermal

  9. The effect of winding and core support material on the thermal gain dependence of a fluxgate magnetometer sensor

    Directory of Open Access Journals (Sweden)

    D. M. Miles

    2017-10-01

    Full Text Available Fluxgate magnetometers are an important tool in geophysics and space physics but are typically sensitive to variations in sensor temperature. Changes in instrumental gain with temperature, thermal gain dependence, are thought to be predominantly due to changes in the geometry of the wire coils that sense the magnetic field and/or provide magnetic feedback. Scientific fluxgate magnetometers typically employ some form of temperature compensation and support and constrain wire sense coils with bobbins constructed from materials such as MACOR machinable ceramic (Corning Inc. which are selected for their ultra-low thermal deformation rather than for robustness, cost, or ease of manufacturing. We present laboratory results comparing the performance of six geometrically and electrically matched fluxgate sensors in which the material used to support the windings and for the base of the sensor is varied. We use a novel, low-cost thermal calibration procedure based on a controlled sinusoidal magnetic source and quantitative spectral analysis to measure the thermal gain dependence of fluxgate magnetometer sensors at the ppm°C−1 level in a typical magnetically noisy university laboratory environment. We compare the thermal gain dependence of sensors built from MACOR, polyetheretherketone (PEEK engineering plastic (virgin, 30 % glass filled and 30 % carbon filled, and acetal to examine the trade between the thermal properties of the material, the impact on the thermal gain dependence of the fluxgate, and the cost and ease of manufacture. We find that thermal gain dependence of the sensor varies as one half of the material properties of the bobbin supporting the wire sense coils rather than being directly related as has been historically thought. An experimental sensor constructed from 30 % glass-filled PEEK (21.6 ppm°C−1 had a thermal gain dependence within 5 ppm°C−1 of a traditional sensor constructed from MACOR ceramic (8.1

  10. NetPICOmag: A low-cost networked magnetometer and its applications

    Science.gov (United States)

    Schofield, I.; Connors, M.; Russell, C. T.

    2012-03-01

    NetPICOmag (NPM) is the culmination of a design effort to build a compact, low-cost, laboratory-grade, networked magnetometer designed for remote autonomous operation, suited for research and education. NPM allows wide placement of magnetometers sensitive enough to detect auroral activity and the daily variation, and is suitable for education projects and a range of geophysical applications. The use of networked microcontrollers and GPS timing is applicable to other small instruments for field or local deployment, and an onboard data logging capability has also been demonstrated. We illustrate the value of the placement of low-cost magnetometers to increase coverage in an area through the study of a Pc 5 pulsation event which took place on September 4, 2010. By combining results with those from auroral zone magnetometers supporting the THEMIS project, we find that the phase velocity of these morning sector pulsations was northward on the ground. The event took place under very quiet solar wind conditions, and credible mapping associates it with the inner magnetosphere. Another aspect beyond increasing areal coverage is increasing density of coverage, which becomes feasible with instruments of very low cost. We examine aspects of the April 5, 2010 space weather event which are possible to deduce from closely spaced magnetometers.

  11. Ground based magnetometers: The workhorse of the magnetospheric-ionospheric community

    Science.gov (United States)

    Gjerloev, J. W.

    2011-12-01

    For decades ground based magnetometers have proven to be the workhorse of magnetosphere-ionosphere physics and their importance is indisputable. SuperMAG is the next logical step for the ground magnetometer community to take in the development of a user friendly data service enabling an understanding as well as monitoring of the global electric current system. The data set provided by the ground magnetometer community is truly unique since it provide continuous and nearly global measurement of a fundamental parameter - the ground level magnetic field perturbations. The very strength of this data set also resulted in painstaking and labor-intensive data-handling, which effectively limited research. Analysts faced several inherent complications: confusing or even unknown coordinate systems, a multitude of data artifacts and errors, unknown baselines, and even difficulties obtaining data. These problems have resulted in a serious underutilization of data from magnetometers. In this paper we present a solution to these complications (the SuperMAG initiative) which is a worldwide collaboration of organizations and national agencies that currently operate more than 300 ground based magnetometers. SuperMAG provides easy access to validated ground magnetic field perturbations in the same coordinate system, identical time resolution and with a common baseline removal approach. The purpose of SuperMAG it to help scientists, teachers, students and the general public have easy access to measurements of the Earth's magnetic field. The presentation will focus on current and future SuperMAG capabilities illustrating the potential for now-casting and eventually forecasting.

  12. Nonlinear temperature compensation of fluxgate magnetometers with a least-squares support vector machine

    International Nuclear Information System (INIS)

    Pang, Hongfeng; Chen, Dixiang; Pan, Mengchun; Luo, Shitu; Zhang, Qi; Luo, Feilu

    2012-01-01

    Fluxgate magnetometers are widely used for magnetic field measurement. However, their accuracy is influenced by temperature. In this paper, a new method was proposed to compensate the temperature drift of fluxgate magnetometers, in which a least-squares support vector machine (LSSVM) is utilized. The compensation performance was analyzed by simulation, which shows that the LSSVM has better performance and less training time than backpropagation and radical basis function neural networks. The temperature characteristics of a DM fluxgate magnetometer were measured with a temperature experiment box. Forty-five measured data under different magnetic fields and temperatures were obtained and divided into 36 training data and nine test data. The training data were used to obtain the parameters of the LSSVM model, and the compensation performance of the LSSVM model was verified by the test data. Experimental results show that the temperature drift of magnetometer is reduced from 109.3 to 3.3 nT after compensation, which suggests that this compensation method is effective for the accuracy improvement of fluxgate magnetometers. (paper)

  13. A dumbbell-shaped hybrid magnetometer operating in DC-10 kHz

    Science.gov (United States)

    Shi, Hongyu; Wang, Yanzhang; Chen, Siyu; Lin, Jun

    2017-12-01

    This study is motivated by the need to design a hybrid magnetometer operating in a wide-frequency band from DC to 10 kHz. To achieve this objective, a residence times difference fluxgate magnetometer (RTDFM) and an induction magnetometer (IM) have been integrated into a compact form. The hybrid magnetometer has a dumbbell-shaped structure in which the RTDFM transducer is partially inserted into the tube cores of the IM. Thus, the sensitivity of the RTDFM is significantly improved due to the flux amplification. The optimal structure, which has maximum sensitivity enhancement, was obtained through FEM analysis. To validate the theoretical analysis, the optimal hybrid magnetometer was manufactured, and its performance was evaluated. The device has a sensitivity of 45 mV/nT at 1 kHz in IM mode and 0.38 μs/nT in RTDFM mode, which is approximately 3.45 times as large as that of the single RTDFM structure. Furthermore, to obtain a lower noise performance in the entire frequency band, two operation modes switch at the cross frequency (0.16 Hz) of their noise levels. The noise level is 30 pT/√Hz in RTDFM mode and 0.07 pT/√Hz at 1 kHz in IM mode.

  14. Sounding of the Plasmasphere by McMAC Magnetometers

    Science.gov (United States)

    Chi, P. J.; McMAC Team

    2012-04-01

    Properly positioned ground magnetometers can be used to detect resonance of magnetospheric field lines as a way to make unique observations of the plasma mass density of the magnetosphere. In this paper we describe the field line resonance (FLR) frequencies systematically observed by the Mid-continent MAgnetoseismic Chain (McMAC), which consists of 10 stations in the United States and Mexico along 300° magnetic longitude. With an average separation by 272 km between adjacent stations McMAC is well suited to remotely sensing the plasma density at L-values between 1.6 and 3.3 through the gradient method of FLR measurements. We analyzed a full year of McMAC observations spanning between July 2006 and June 2007, and FLR frequencies were automatically identified in cross-phase and cross-power spectrograms by a computer routine. In all of the FLR observations by pairs of McMAC stations, the occurrence rate of FLR can reach as high as 55% around local noon at L = 2.7. The occurrence rate drops at lower latitudes due to weaker FLR signals. At L = 3.3 the FLR occurrence is clearly reduced in afternoon hours, possibly because of occasional presence of the plasmapause that can obstruct FLR generation and/or detection. By examining the results from all possible pairs of McMAC stations, we find that, at L ≤ 2.5, FLR signatures can still be found even when the separation between two stations exceeds 1000 km. The fundamental mode FLR frequencies, in addition to the inferred equatorial plasma mass densities of the magnetosphere, are tabulated with respect to L-value and time. The most probable fundamental mode frequency is found to be approximately 75 mHz at L = 1.6 and decreases with increasing L-value. The distribution of the fundamental mode frequency at L = 3.3, however, exhibits two distinct groups: The lower frequencies centered at 10 mHz representing the measurements inside the plasmasphere whereas the higher frequencies centered at 39 mHz indicating the faster field

  15. Employer Branding

    DEFF Research Database (Denmark)

    Frimann, Søren; Mønsted, Bolette Rye

    2012-01-01

    Employer branding er både for den private og den offentlige sektor blevet en måde, de kan imødekomme ændrede arbejdsmarkedsvilkår og organisatoriske udfordringer i en postmoderne og globaliseret verden. Den aktuelle finanskrise har skabt nye udfordringer for organisationer i deres bestræbelser på...... at tiltrække- og fastholde attraktive medarbejdere. Men hvilken betydning har det, når Grundfos siger ”Mennesket er i fokus”, og hvad siger ”mangfoldighed” om Københavns Kommune som arbejdsplads i relation til employer branding? Er der egentlig sammenhæng mellem tankerne bag employer branding og de eksternt...... kommunikerede employer brandprodukter. Eller bliver det unikke ved arbejdspladserne ersattet af buzzwords uden substans og inddragelse af ansatte og interessenter? Artiklen har til formål at vurdere disse spørgsmål på baggrund af analyser af to cases med employer branding....

  16. Phase-sensitive dc magnetometer based on magnetic–electromagnetic–magnetostrictive–piezoelectric heterostructure

    Directory of Open Access Journals (Sweden)

    Mingji Zhang

    2017-05-01

    Full Text Available A phase-sensitive dc magnetometer is developed by combining a pair of permanent magnets, an electromagnetic coil, and a magnetostrictive–piezoelectric laminate in one direction to form a four-phase magnetic–electromagnetic–magnetostrictive–piezoelectric heterostructure. The dc magnetic field sensing in the magnetometer is based on the detection of the phase difference between the off-resonance magnetoelectric voltage manipulated by the dc magnetic field to be measured and the resonance electric current referenced at zero dc magnetic field, both under a preset bias magnetic field. The theoretical and experimental results confirm a high and linear dc magnetic field sensitivity of –0.21 °/Oe over a positive and negative dc magnetic field range of ±150 Oe with a small nonlinearity of 1.7%. The magnetometer has the ability to determine dc magnetic field direction and its sensitivity is independent of zero-field resonance electric current amplitude.

  17. Construction and calibration of a low cost and fully automated vibrating sample magnetometer

    Energy Technology Data Exchange (ETDEWEB)

    El-Alaily, T.M., E-mail: toson_alaily@yahoo.com [Physics Department, Faculty of Science, Tanta University, Tanta (Egypt); El-Nimr, M.K.; Saafan, S.A.; Kamel, M.M.; Meaz, T.M. [Physics Department, Faculty of Science, Tanta University, Tanta (Egypt); Assar, S.T. [Engineering Physics and Mathematics Department, Faculty of Engineering, Tanta University, Tanta (Egypt)

    2015-07-15

    A low cost vibrating sample magnetometer (VSM) has been constructed by using an electromagnet and an audio loud speaker; where both are controlled by a data acquisition device. The constructed VSM records the magnetic hysteresis loop up to 8.3 KG at room temperature. The apparatus has been calibrated and tested by using magnetic hysteresis data of some ferrite samples measured by two scientifically calibrated magnetometers; model (Lake Shore 7410) and model (LDJ Electronics Inc. Troy, MI). Our VSM lab-built new design proved success and reliability. - Highlights: • A low cost automated vibrating sample magnetometer VSM has been constructed. • The VSM records the magnetic hysteresis loop up to 8.3 KG at room temperature. • The VSM has been calibrated and tested by using some measured ferrite samples. • Our VSM lab-built new design proved success and reliability.

  18. Development, construction and analysis of the "Ørsted" fluxgate magnetometer

    DEFF Research Database (Denmark)

    Nielsen, Otto V; Petersen, Jan Raagaard; Primdahl, Fritz

    1995-01-01

    The experiments and theoretical considerations leading to the construction of a high-performance three-axis fluxgate magnetometer are described. The magnetometer will be used (1996) in the Earth's field mapping satellite named "Ørsted". The fluxgate sensors are based on stress-annealed metallic...... on the basis of nonlinear electrical circuitry. It is furthermore shown that the ring-core demagnetizing field obeys a simple cosine law which permits the calculation of the sensor sensitivity with high accuracy. The sensitivity, that is the signal-to-noise ratio, is ultimately determined by the sensor noise...... which is about 15 pT RMS (0.06-10 Hz), corresponding to a noise power density (1/f noise) of 6.2 pT Hz-1/2 at 1 Hz. The actual magnetometer operating range and sensitivity is determined by the 1 bit resolution of the Earth's field represented by the output from the 18 bit AD converter used...

  19. A magnetometer-free indoor human localization based on loosely coupled IMU/UWB fusion.

    Science.gov (United States)

    Zihajehzadeh, Shaghayegh; Yoon, Paul K; Park, Edward J

    2015-01-01

    The magnetic distortions in indoor environment affects the accuracy of yaw angle estimation using magnetometer. Thus, the accuracy of indoor localization based on inertial-magnetic sensors will be affected as well. To address this issue, this paper proposes a magnetometer-free solution for indoor human localization and yaw angle estimation. The proposed algorithm fuses a wearable inertial sensor consisting of MEMS-based accelerometer and gyroscope with a portable ultra-wideband (UWB) localization system in a cascaded two-step filter consisting of a tilt Kalman filter and a localization Kalman filter. By benchmarking against an optical motion capture system, the experimental results show that the proposed algorithm can accurately track position and velocity as well as the yaw angle without using magnetometer.

  20. Study of 3He Rabi nutations by optically-pumped cesium magnetometers

    Science.gov (United States)

    Koch, Hans-Christian; Bison, Georg; Grujić, Zoran Dragan; Heil, Werner; Kasprzak, Malgorzata; Knowles, Paul; Kraft, Andreas; Pazgalev, Anatoly; Schnabel, Allard; Voigt, Jens; Weis, Antoine

    2017-10-01

    We describe a method for recording the Rabi nutation of nuclear spin polarized 3He by optically pumped cesium magnetometers. The measurement is performed by detecting the time-dependent magnetic field produced by the 3He magnetization. The observed signals are compared to theoretical models and the results are used to precisely trace the evolution of the magnetization. This procedure represents a convenient way to control and measure the Rabi flip angle and the degree of spin polarization in experiments using 3He magnetometers. The method requires only very coarse knowledge of the applied magnetic field's magnitude.

  1. Real-time geomagnetic data from a Raspberry Pi magnetometer network in the UK

    OpenAIRE

    Beggan, Ciaran

    2017-01-01

    In 2014, BGS and the University of Lancaster won an STFC Public Engagement grant to build and deploy 10 Raspberry Pi magnetometers to secondary schools across the UK. The system uses a Raspberry Pi computer as a logging and data transfer device, connected to a set of three orthogonal miniature fluxgate magnetometers. The system has a nominal sensitivity of around 1 nanoTesla (nT), in each component direction (North, East and Down). This is around twenty times less sensitive than a current sci...

  2. A comparison of vector and radial magnetometer arrays for whole-head magnetoencephalography

    Energy Technology Data Exchange (ETDEWEB)

    Hughett, P. [Lawrence Berkeley National Lab., CA (United States); Miyauchi, S. [Ministry of Post and Telecommunications, Tokyo (Japan). Communications Research Lab.

    1996-02-01

    The number of detectors in magnetometer arrays for magnetoencephalography (MEG) has been steadily increasing, with systems containing or more detectors now possible. It is of considerable interest to know how best to configure such a large array. In particular, is it useful to measure all three components of the magnetic field, rather than just the radial component? This paper compares the information content provided by three different magnetometer arrays for whole-head measurements, using a definition of information content developed by Kemppainen and Ilmoniemi.

  3. Magnetic dichroism in photoemission: a new element-specific magnetometer with atomic-layer resolution

    International Nuclear Information System (INIS)

    Starke, K.; Arenholz, E.; Kaindl, G.

    1998-01-01

    Full text: Magnetic coupling in layered metallic structures has become a key issue in thin-film magnetism since the observation of oscillatory exchange coupling across non-ferromagnetic spacer layers. Although this phenomenon was discovered in rare earths (RE) superlattices, mostly transition-metal systems have been studied and are now applied in data-storage industry. An understanding of the coupling mechanisms has been reached after a fabrication of high-quality interfaces became possible. It allowed, in particular, the experimental finding of induced ferromagnetic order in 'nonmagnetic' atomic layers near an interface, using element-specific probes such as magnetic circular dichroism in x-ray absorption. - In layered RE systems, by contrast, the well known intermiscibility has prevented a preparation of atomically sharp interfaces, and all RE superlattices studied so far showed interdiffusion zones of several atomic layers. In the present overview, we report the first fabrication of atomically flat heteromagnetic RE interfaces, their structural characterization and their magnetic analysis using magnetic dichroism in photoemission (MDPE). This new tool gives access to the magnetization of individual atomic layers near interfaces in favourite cases. Merits of MDPE as a magnetometer are demonstrated at the example of Eu/Gd(0001), where chemical shifts of core-level photoemission lines allow to spectroscopically separate up to four different atomic layers. The high surface sensitivity of MDPE, together with the well known dependence of the core-level binding energies on the coordination number of the photo emitting atom, opens the door to future site-specific studies of magnetism in sub-monolayer systems such as 'nanowires'

  4. Student employment

    DEFF Research Database (Denmark)

    Jacob, Marita; Gerth, Maria; Weiss, Felix

    2018-01-01

    In this article, we examine social origin differences in employment patterns across different stages of higher education and compare these differences between vocational and academic fields of study. Using data from a large-scale German student survey, we study the development of inequality, acco...... decrease as students progress through higher education. While we find evidence for this hypothesis, we also show in multivariate models that the reduction of inequality in the student labour market is explained by prior differences between social origin groups.......In this article, we examine social origin differences in employment patterns across different stages of higher education and compare these differences between vocational and academic fields of study. Using data from a large-scale German student survey, we study the development of inequality...

  5. Illegal employment

    Directory of Open Access Journals (Sweden)

    Jana Mervartová

    2013-01-01

    Full Text Available Since 2007 Labour Code contains the definition of dependent work, which can be carried out only in labour-law relations. The Amendment to Labour Code from 2012 makes the definition more precise, when it stipulates essential elements of dependent work and designates the others as conditions, under which dependent work should be carried out. The Amendment to Employment Act changes the definition of illegal work. Illegal work is a performance of dependent work by natural person except for labour-law relation, or if natural person – foreigner carries out work in conflict with issued permission to employment or without this permission. Since 2012 sanctions for illegal work were increased. Labour inspection is entitled to impose sanctions, in case of foreigners it is Customs Office. For control purposes employer is obliged to have copies of documents at the workplace proving the existence of labour-law relation. Goal of controls and high fines is to limit illegal employment of citizens of Czech Republic and foreigners as well. Illegal work has unfavourable economic impact on state budget. It comes to extensive tax evasions and also to evasions within health insurance and social security. If a concluded commercial-law relation meets the attributes of dependent work, then it stands for a concealed legal relationship. Tax Office can subsequently assess an income tax to businessman. Labour-law relationship enjoys a higher legal protection than commercial-law relationship; nonetheless it is not suitable to limit liberty of contract in cases when it is not unambiguously a dependent activity.

  6. Two-channel recoder for magnetometer with energy-independent mass memory device

    International Nuclear Information System (INIS)

    Korzinin, V.N.; Selivanov, A.M.

    1993-01-01

    The paper describes a two-channel digit-to-analog recorder designed for converting the sequence of pulses from proton magnetometer (MMH-203) outlet; the device enables processing of the pulses and their recording in RAM and on the tape of the analog recorder. The availability of nonvolotile RAM allows to transmit digit information to a computer (BK-0010) for its further processing

  7. The Future of Ground Magnetometer Arrays in Support of Space Weather Monitoring and Research

    Science.gov (United States)

    Engebretson, Mark; Zesta, Eftyhia

    2017-11-01

    A community workshop was held in Greenbelt, Maryland, on 5-6 May 2016 to discuss recommendations for the future of ground magnetometer array research in space physics. The community reviewed findings contained in the 2016 Geospace Portfolio Review of the Geospace Section of the Division of Atmospheric and Geospace Science of the National Science Foundation and discussed the present state of ground magnetometer arrays and possible pathways for a more optimal, robust, and effective organization and scientific use of these ground arrays. This paper summarizes the report of that workshop to the National Science Foundation (Engebretson & Zesta, as well as conclusions from two follow-up meetings. It describes the current state of U.S.-funded ground magnetometer arrays and summarizes community recommendations for changes in both organizational and funding structures. It also outlines a variety of new and/or augmented regional and global data products and visualizations that can be facilitated by increased collaboration among arrays. Such products will enhance the value of ground-based magnetometer data to the community's effort for understanding of Earth's space environment and space weather effects.

  8. Analysis on common faults in G856 AX proton precession magnetometer

    International Nuclear Information System (INIS)

    Zhang Yungui; Zhang Biao; Wang Meili

    1995-01-01

    The authors mainly introduce common faults in G856 AX proton precession magnetometer in operation and their analysis so that the users can eliminate them, avoiding to repair blindly. In the mean time, it is a beneficial reference material for geophysicists and instrument designers

  9. Design Principles of A Sigma-delta Flux-gate Magnetometer

    Science.gov (United States)

    Magnes, W.; Valavanoglou, A.; Pierce, D.; Frank, A.; Schwingenschuh, K.

    A state-of-the-art flux-gate magnetometer is characterised by magnetic field resolution of several pT in a wide frequency range, low power consumption, low weight and high robustness. Therefore, flux-gate magnetometers are frequently used for ground-based Earth's field observation as well as for measurements aboard scientific space missions. But both traditional analogue and recently developed digital flux-gate magnetometers need low power and high-resolution analogue-to-digital converters for signal quan- tization. The disadvantage of such converters is the low radiation hardness. This fact has led to the idea of combining a traditional analogue flux-gate regulation circuit with that of a discretely realized sigma-delta converter in order to get a radiation hard and further miniaturized magnetometer. The name sigma-delta converter is derived from putting an integrator in front of a 1-bit delta modulator which forms the sigma-delta loop. It is followed by a digital decimation filter realized in a field-programmable gate array (FPGA). The flux-gate regulation and the sigma-delta loop are quite similar in the way of realizing the integrator and feedback circuit, which makes it easy to com- bine these two systems. The presented talk deals with the design principles and the results of a first bread board model.

  10. MgB2 magnetometer with directly coupled pick-up loop

    NARCIS (Netherlands)

    Portesi, C.; Mijatovic, D.; Veldhuis, Dick; Brinkman, Alexander; Monticone, E.; Gonnelli, R.S.

    2006-01-01

    magnetometer with a directly coupled pick-up loop. We used an all in situ technique for fabricating magnesium diboride films, which consists of the co-evaporation of B and Mg by means of an e-gun and a resistive heater respectively. Consequently, we realized the superconducting device, which

  11. Bundle of Hysteresis Loops at Temperature Sweep Measured by Vibrating Sample Magnetometer

    Czech Academy of Sciences Publication Activity Database

    Vondráček, Martin; Žák, Tomáš

    2002-01-01

    Roč. 53, 10/s (2002), s. 142-144 ISSN 1335-3632. [Magnetic Measurements 2002. Bratislava, 11.09.2002-13.09.2002] R&D Projects: GA ČR GA102/01/1335 Institutional research plan: CEZ:AV0Z2041904 Keywords : vibrating sample magnetometer * hysteresis loop- thermomagnetic curve Subject RIV: BM - Solid Matter Physics ; Magnetism

  12. Magnetogate: Using an iPhone Magnetometer for Measuring Kinematic Variables

    Science.gov (United States)

    Temiz, Burak Kagan; Yavuz, Ahmet

    2016-01-01

    This paper presents a method to measure the movement of an object from specific locations on a straight line using an iPhone's magnetometer. In this method, called "magnetogate," an iPhone is placed on a moving object (in this case a toy car) and small neodymium magnets are arranged at equal intervals on one side of a straight line. The…

  13. Performance Improvement of Inertial Navigation System by Using Magnetometer with Vehicle Dynamic Constraints

    Directory of Open Access Journals (Sweden)

    Daehee Won

    2015-01-01

    Full Text Available A navigation algorithm is proposed to increase the inertial navigation performance of a ground vehicle using magnetic measurements and dynamic constraints. The navigation solutions are estimated based on inertial measurements such as acceleration and angular velocity measurements. To improve the inertial navigation performance, a three-axis magnetometer is used to provide the heading angle, and nonholonomic constraints (NHCs are introduced to increase the correlation between the velocity and the attitude equation. The NHCs provide a velocity feedback to the attitude, which makes the navigation solution more robust. Additionally, an acceleration-based roll and pitch estimation is applied to decrease the drift when the acceleration is within certain boundaries. The magnetometer and NHCs are combined with an extended Kalman filter. An experimental test was conducted to verify the proposed method, and a comprehensive analysis of the performance in terms of the position, velocity, and attitude showed that the navigation performance could be improved by using the magnetometer and NHCs. Moreover, the proposed method could improve the estimation performance for the position, velocity, and attitude without any additional hardware except an inertial sensor and magnetometer. Therefore, this method would be effective for ground vehicles, indoor navigation, mobile robots, vehicle navigation in urban canyons, or navigation in any global navigation satellite system-denied environment.

  14. Magnetoencephalography with a Cs-based high-sensitivity compact atomic magnetometer

    Science.gov (United States)

    Sheng, Jingwei; Wan, Shuangai; Sun, Yifan; Dou, Rongshe; Guo, Yuhao; Wei, Kequan; He, Kaiyan; Qin, Jie; Gao, Jia-Hong

    2017-09-01

    In recent years, substantial progress has been made in developing a new generation of magnetoencephalography (MEG) with a spin-exchange relaxation free (SERF)-based atomic magnetometer (AM). An AM employs alkali atoms to detect weak magnetic fields. A compact AM array with high sensitivity is crucial to the design; however, most proposed compact AMs are potassium (K)- or rubidium (Rb)-based with single beam configurations. In the present study, a pump-probe two beam configuration with a Cesium (Cs)-based AM (Cs-AM) is introduced to detect human neuronal magnetic fields. The length of the vapor cell is 4 mm, which can fully satisfy the need of designing a compact sensor array. Compared with state-of-the-art compact AMs, our new Cs-AM has two advantages. First, it can be operated in a SERF regime, requiring much lower heating temperature, which benefits the sensor with a closer distance to scalp due to ease of thermal insulation and less electric heating noise interference. Second, the two-beam configuration in the design can achieve higher sensitivity. It is free of magnetic modulation, which is necessary in one-beam AMs; however, such modulation may cause other interference in multi-channel circumstances. In the frequency band between 10 Hz and 30 Hz, the noise level of the proposed Cs-AM is approximately 10 f T/Hz1/2, which is comparable with state-of-the-art K- or Rb-based compact AMs. The performance of the Cs-AM was verified by measuring human auditory evoked fields (AEFs) in reference to commercial superconducting quantum interference device (SQUID) channels. By using a Cs-AM, we observed a clear peak in AEFs around 100 ms (M100) with a much larger amplitude compared with that of a SQUID, and the temporal profiles of the two devices were in good agreement. The results indicate the possibility of using the compact Cs-AM for MEG recordings, and the current Cs-AM has the potential to be designed for multi-sensor arrays and gradiometers for future neuroscience

  15. Prevention of Post Transfusion Hepatitis Employing Sensitive Assay for Hepatitis B Surface Antigen Screening(Topics in Transfusion Medicine 1990 : Autologous Transfusion and Post-Transfusion Hepatitis)

    OpenAIRE

    小島, 秀男; 大竹, 幸子; 富樫, 和枝; 石口, 重子; 山田, 恵子; 品田, 章二; Kojima, Hideo; Ohtake, Sachiko; Togashi, Kazue; Ishiguchi, Shigeko; Yamada, Keiko; Shinada, Shoji

    1990-01-01

    Post transfusion Hepatitis (PTH) is one of serious side effects and some times lead to fulminant hepatic failure in case transfused blood contain very low level (under the sensitivity of usual screening method) of hepatitis B virus (HBV). Redcross blood center and blood transfusion devision of our hospital have been employed reverse passive hemmaglutination method (RPHA) for HBsAg screening. Authors employed EIA for sensitive HBsAg test system and compared with RPHA method. Of 2,255 sera from...

  16. Magnetorelaxometry of few Fe3O4 nanoparticles at 77 K employing a self-compensated SQUID magnetometer

    International Nuclear Information System (INIS)

    Guillaume, Alexander; Scholtyssek, Jan M.; Lak, Aidin; Kassner, Alexander; Ludwig, Frank; Schilling, Meinhard

    2016-01-01

    Magnetic nanoparticles (MNPs) are of great interest for industrial and medical applications. Therefore, the properties of the particles have to be well controlled. Several magnetic measurement schemes have been developed in order to determine particle parameters such as size distribution and structural properties. In general, systems are designed either for the analysis of large amounts of MNP (≫1000) or for single particle investigation. Up to now, the region in between has been less studied. However, small and well defined amounts of MNPs are of high interest, e.g. for the systematic investigation of particle–particle interactions. In this paper, we present a method using electron beam lithographic preparation of small amounts of MNPs directly on a self-compensating high-temperature superconducting quantum interference device (SQUID) with micrometer dimensions which is insensitive to homogeneous fields and first order gradients but very sensitive to internal magnetic dipole fields. Magnetorelaxometry (MRX) measurements were carried out at 77 K sample temperature in a magnetically shielded room in order to analyze the dynamic behavior of MNP samples and to evaluate the detection limit of our SQUID sensors. Calculations based on the magnetic moment superposition model (MSM) and finite element simulations (FEM) indicate that the MNP samples can be fabricated in a well-defined way by the presented method. Based on MRX measurements of a sample with 200 single-core magnetite MNPs with core diameters of 12 nm, we estimate the detection limit of our SQUID MRX setup as 70 MNPs. - Highlights: • Novel self-compensated superconducting quantum interference device (SQUID). • Electron-beam lithographical patterning of magnetic nanoparticles directly on SQUID. • Magnetorelaxometric detection of 200 nanoparticles with diameter of 12 nm at 77 K. • FEM simulations provide detection limit of less than 100 nanoparticles.

  17. Magnetorelaxometry of few Fe3O4 nanoparticles at 77 K employing a self-compensated SQUID magnetometer

    Science.gov (United States)

    Guillaume, Alexander; Scholtyssek, Jan M.; Lak, Aidin; Kassner, Alexander; Ludwig, Frank; Schilling, Meinhard

    2016-06-01

    Magnetic nanoparticles (MNPs) are of great interest for industrial and medical applications. Therefore, the properties of the particles have to be well controlled. Several magnetic measurement schemes have been developed in order to determine particle parameters such as size distribution and structural properties. In general, systems are designed either for the analysis of large amounts of MNP (≫1000) or for single particle investigation. Up to now, the region in between has been less studied. However, small and well defined amounts of MNPs are of high interest, e.g. for the systematic investigation of particle-particle interactions. In this paper, we present a method using electron beam lithographic preparation of small amounts of MNPs directly on a self-compensating high-temperature superconducting quantum interference device (SQUID) with micrometer dimensions which is insensitive to homogeneous fields and first order gradients but very sensitive to internal magnetic dipole fields. Magnetorelaxometry (MRX) measurements were carried out at 77 K sample temperature in a magnetically shielded room in order to analyze the dynamic behavior of MNP samples and to evaluate the detection limit of our SQUID sensors. Calculations based on the magnetic moment superposition model (MSM) and finite element simulations (FEM) indicate that the MNP samples can be fabricated in a well-defined way by the presented method. Based on MRX measurements of a sample with 200 single-core magnetite MNPs with core diameters of 12 nm, we estimate the detection limit of our SQUID MRX setup as 70 MNPs.

  18. Real-Time Hand-Held Magnetometer Array

    Science.gov (United States)

    2016-04-01

    disturbance, such as an automobile , surface vessel, or other metal objects, assuming they are not moving. To address this question, semi-numerical...Module connector details Pin Signal Description 1 CHASSIS Chassis ground 2 GND Power supply ground 3 Vin Power supply (9.5V to 16V) 4 Vin Power

  19. Development of Geomagnetic Monitoring System Using a Magnetometer for the Field

    Science.gov (United States)

    Lee, Young-Cheol; Kim, Sung-Wook; Choi, Eun-Kyeong; Kim, In-Soo

    2014-05-01

    Three institutes including KMA (Korea Meteorological Administration), KSWC (Korean Space Weather Center) of NRRA (National Radio Research Agency) and KIGAM (Korea Institute of Geoscience and Mineral Resources) are now operating magnetic observatories. Those observatories observe the total intensity and three components of geomagnetic element. This paper comes up with a magnetic monitoring system now under development that uses a magnetometer for field survey. In monitoring magnetic variations in areas (active faults or volcanic regions), more reliable results can be obtained when an array of several magnetometers are used rather than a single magnetometer. In order to establish and operate a magnetometer array, such factors as expenses, convenience of the establishment and operation of the array should be taken into account. This study has come up with a magnetic monitoring system complete with a magnetometer for the field survey of our own designing. A magnetic monitoring system, which is composed of two parts. The one is a field part and the other a data part. The field part is composed of a magnetometer, an external memory module, a power supply and a set of data transmission equipment. The data part is a data server which can store the data transmitted from the field part, analyze the data and provide service to the web. This study has developed an external memory module for ENVI-MAG (Scintrex Ltd.) using an embedded Cortex-M3 board, which can be programmed, attach other functional devices (SD memory cards, GPS antennas for time synchronization, ethernet cards and so forth). The board thus developed can store magnetic measurements up to 8 Gbytes, synchronize with the GPS time and transmit the magnetic measurements to the data server which is now under development. A monitoring system of our own developing was installed in Jeju island, taking measurements throughout Korea. Other parts including a data transfer module, a server and a power supply using solar

  20. Micromechanical torque magnetometer with sub-monolayer sensitivity

    International Nuclear Information System (INIS)

    Min, D.H.; McCallum, A.; Russek, Stephen E.; Moreland, John

    2005-01-01

    We have developed a micromechanical torque sensor with sub-monolayer sensitivity for in situ monitoring of the magnetic moment of thin films during deposition. The film is deposited onto a microcantilever. The torque on the film is determined by measuring the deflection of the cantilever due to a small AC magnetic field perpendicular to the surface of the film. The microcantilevers have a high mechanical quality factor, large surface area, low spring constant, and high resonance frequency to improve film sensitivity to thickness. A phase-locked loop minimizes the resonance frequency shift of the cantilever due to mass loading and temperature drift that would otherwise affect the measurement of magnetic torque. The demonstrated thickness sensitivity for a Ni 0.8 Fe 0.2 film and a Ni 0.8 Fe 0.2 /Cu multilayer film is less than 0.1 nm

  1. New Magnetic Field Model for Saturn From Cassini Radio and Magnetometers Observations: The Birotor Dipole

    Science.gov (United States)

    Galopeau, P. H. M.

    2017-12-01

    Since the insertion of Cassini in the Saturnian system in July 2004, the radio and plasma wave science (RPWS) experiment on board the spacecraft revealed the presence of two distinct and variable rotation periods in the Saturnian kilometric radiation (SKR) which were attributed to the northern and southern hemispheres respectively. The present study is based on the hypothesis that the periodic time modulations present in the SKR are mainly due to the rotation of Saturn's inner magnetic field. The existence of a double period implies that the inner field is not only limited to a simple rotation dipole but displays more complex structures having the same time periodicities than the radio emission. In order to build a model of this complex magnetic field, it is absolutely necessary to know the accurate phases of rotation linked with the two periods. The radio observations from the RPWS experiment allow a continuous and accurate follow-up of these rotation phases, since the SKR emission is permanently observable and produced very close to the planetary surface. A continuous wavelet transform analysis of the intensity of the SKR signal received at 290 kHz between July 2004 and June 2012 was performed in order to calculate in the same time the different periodicities and phases. The rotation phases associated to the main two periods allow us to define a North and South longitude system essential for such a study. In this context, a dipole model ("birotor dipole") was proposed for Saturn's inner magnetic field: this dipole presents the particularity to have North and South poles rotating around Saturn's axis at two different angular velocities; this dipole is tilted and not centered. 57 Cassini's revolutions, the periapsis of which is less than 5 Saturnian radii, have been selected for this study. For each of these chosen orbits, it is possible to fit with high precision the measurements of the MAG data experiment given by the magnetometers embarked on board Cassini. A

  2. A low-temperature high-sensitivity torsion balance magnetometer with in situ stator adjustment

    Science.gov (United States)

    Matthews, A. J.; Usher, A.; Williams, C. D. H.

    2004-08-01

    Torsion balance magnetometry can be used as a versatile probe of two-dimensional electron systems. We have developed a highly sensitive magnetometer, utilizing capacitive proximity detection of the rotor position, for use at temperatures below 10 mK. The instrument incorporates two piezo-electric linear motors to enable the stator positions to be adjusted in situ at base temperature. The magnetometer responsivity is inversely proportional to the square of the rotor-stator separation and the novel linear motor technique, accompanied by effective vibration isolation and optimized capacitance bridge electronics, achieves a resolution 6.5×10-12 N m Hz-1/2. This resolution, together with the low temperatures attainable, allows for experiments that probe the family of quantum fluid states responsible for the fractional quantum Hall effect, even at filling factors greater than one.

  3. On-orbit real-time magnetometer bias determination for micro-satellites without attitude information

    Directory of Open Access Journals (Sweden)

    Zhang Zhen

    2015-10-01

    Full Text Available Due to the disadvantages such as complex calculation, low accuracy of estimation, and being non real time in present methods, a new real-time algorithm is developed for on-orbit magnetometer bias determination of micro-satellites without attitude knowledge in this paper. This method uses the differential value approach. It avoids the impact of quartic nature and uses the iterative method to satisfy real-time applications. Simulation results indicate that the new real-time algorithm is more accurate compared with other methods, which are also tested by an experiment system using real noise data. With the new real-time algorithm, a magnetometer calibration can be taken on-orbit and will reduce the demand for computing power effectively.

  4. Searching for axion stars and Q -balls with a terrestrial magnetometer network

    Science.gov (United States)

    Jackson Kimball, D. F.; Budker, D.; Eby, J.; Pospelov, M.; Pustelny, S.; Scholtes, T.; Stadnik, Y. V.; Weis, A.; Wickenbrock, A.

    2018-02-01

    Light (pseudo-)scalar fields are promising candidates to be the dark matter in the Universe. Under certain initial conditions in the early Universe and/or with certain types of self-interactions, they can form compact dark-matter objects such as axion stars or Q -balls. Direct encounters with such objects can be searched for by using a global network of atomic magnetometers. It is shown that for a range of masses and radii not ruled out by existing observations, the terrestrial encounter rate with axion stars or Q -balls can be sufficiently high (at least once per year) for a detection. Furthermore, it is shown that a global network of atomic magnetometers is sufficiently sensitive to pseudoscalar couplings to atomic spins so that a transit through an axion star or Q -ball could be detected over a broad range of unexplored parameter space.

  5. A fast determination method for transverse relaxation of spin-exchange-relaxation-free magnetometer

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Jixi, E-mail: lujixi@buaa.edu.cn; Qian, Zheng; Fang, Jiancheng [School of Instrument Science and Opto-Electronics Engineering, Beihang University, Beijing 100191 (China)

    2015-04-15

    We propose a fast and accurate determination method for transverse relaxation of the spin-exchange-relaxation-free (SERF) magnetometer. This method is based on the measurement of magnetic resonance linewidth via a chirped magnetic field excitation and the amplitude spectrum analysis. Compared with the frequency sweeping via separate sinusoidal excitation, our method can realize linewidth determination within only few seconds and meanwhile obtain good frequency resolution. Therefore, it can avoid the drift error in long term measurement and improve the accuracy of the determination. As the magnetic resonance frequency of the SERF magnetometer is very low, we include the effect of the negative resonance frequency caused by the chirp and achieve the coefficient of determination of the fitting results better than 0.998 with 95% confidence bounds to the theoretical equation. The experimental results are in good agreement with our theoretical analysis.

  6. Research on Intelligent Control System of DC SQUID Magnetometer Parameters for Multi-channel System

    Science.gov (United States)

    Chen, Hua; Yang, Kang; Lu, Li; Kong, Xiangyan; Wang, Hai; Wu, Jun; Wang, Yongliang

    2018-03-01

    In a multi-channel SQUID measurement system, adjusting device parameters to optimal condition for all channels is time-consuming. In this paper, an intelligent control system is presented to determine the optimal working point of devices which is automatic and more efficient comparing to the manual one. An optimal working point searching algorithm is introduced as the core component of the control system. In this algorithm, the bias voltage V_bias is step scanned to obtain the maximal value of the peak-to-peak current value I_pp of the SQUID magnetometer modulation curve. We choose this point as the optimal one. Using the above control system, more than 30 weakly damped SQUID magnetometers with area of 5 × 5 mm^2 or 10 × 10 mm^2 are adjusted and a 36-channel magnetocardiography system perfectly worked in a magnetically shielded room. The average white flux noise is 15 μΦ_0/Hz^{1/2}.

  7. Searching for axion stars and Q-balls with a terrestrial magnetometer network

    Energy Technology Data Exchange (ETDEWEB)

    Jackson Kimball, D. F. [Cal State, East Bay; Budker, D. [UC, Berkeley; Eby, J. [Fermilab; Pospelov, M. [Perimeter Inst. Theor. Phys.; Pustelny, S. [Jagiellonian U.; Scholtes, T. [Fribourg U.; Stadnik, Y. V. [Helmholtz Inst., Mainz; Weis, A. [Fribourg U.; Wickenbrock, A. [Mainz U.

    2017-10-11

    Light (pseudo-)scalar fields are promising candidates to be the dark matter in the Universe. Under certain initial conditions in the early Universe and/or with certain types of self-interactions, they can form compact dark-matter objects such as axion stars or Q-balls. Direct encounters with such objects can be searched for by using a global network of atomic magnetometers. It is shown that for a range of masses and radii not ruled out by existing observations, the terrestrial encounter rate with axion stars or Q-balls can be sufficiently high (at least once per year) for a detection. Furthermore, it is shown that a global network of atomic magnetometers is sufficiently sensitive to pseudoscalar couplings to atomic spins so that a transit through an axion star or Q-ball could be detected over a broad range of unexplored parameter space.

  8. Study of the operation temperature in the spin-exchange relaxation free magnetometer

    International Nuclear Information System (INIS)

    Fang, Jiancheng; Li, Rujie; Duan, Lihong; Chen, Yao; Quan, Wei

    2015-01-01

    We study the influence of the cell temperature on the sensitivity of the spin-exchange relaxation free (SERF) magnetometer and analyze the possibility of operating at a low temperature. Utilizing a 25 × 25 × 25 mm 3 Cs vapor cell with a heating temperature of 85  ∘ C, which is almost half of the value of potassium, we obtain a linewidth of 1.37 Hz and achieve a magnetic field sensitivity of 55 fT/Hz 1/2 in a single channel. Theoretical analysis shows that fundamental sensitivity limits of this device with an active volume of 1 cm 3 could approach 1 fT/Hz 1/2 . Taking advantage of the higher saturated vapor pressure, SERF magnetometer based on Cs opens up the possibility for low cost and portable sensors and is particularly appropriate for lower temperature applications

  9. Study of the operation temperature in the spin-exchange relaxation free magnetometer

    Energy Technology Data Exchange (ETDEWEB)

    Fang, Jiancheng; Li, Rujie, E-mail: lirujie@buaa.edu.cn; Duan, Lihong; Chen, Yao; Quan, Wei [School of Instrument Science and Opto-Electronics Engineering, Beihang University, Beijing 100191 (China)

    2015-07-15

    We study the influence of the cell temperature on the sensitivity of the spin-exchange relaxation free (SERF) magnetometer and analyze the possibility of operating at a low temperature. Utilizing a 25 × 25 × 25 mm{sup 3} Cs vapor cell with a heating temperature of 85 {sup ∘}C, which is almost half of the value of potassium, we obtain a linewidth of 1.37 Hz and achieve a magnetic field sensitivity of 55 fT/Hz{sup 1/2} in a single channel. Theoretical analysis shows that fundamental sensitivity limits of this device with an active volume of 1 cm{sup 3} could approach 1 fT/Hz{sup 1/2}. Taking advantage of the higher saturated vapor pressure, SERF magnetometer based on Cs opens up the possibility for low cost and portable sensors and is particularly appropriate for lower temperature applications.

  10. Automatic torque magnetometer for vacuum-to-high-pressure hydrogen environments

    International Nuclear Information System (INIS)

    Larsen, J.W.; Livesay, B.R.

    1979-01-01

    An automatic torque magnetometer has been developed for use in high-pressure hydrogen. It will contain pressures ranging from vacuum to 200 atm of hydrogen gas at sample temperatures greater than 400 0 C. This magnetometer, which uses an optical lever postion sensor and a restoring force technique has an operating range of 2.0 x 10 3 dyn cm to l.6 x 10 -4 dyn cm. An accompanying digital data collection system extends the sensitivity to 1 x 10 -5 dyn cm as well as increasing the data handling capacity of the system. The magnetic properties of thin films in high-temperature and high-pressure hydrogen environments can be studied using this instruments

  11. Monitoring geomagnetic signals of groundwater movement using multiple underground SQUID magnetometers

    Directory of Open Access Journals (Sweden)

    Henry S.

    2014-01-01

    Full Text Available Groundwater can influence the geomagnetic field measured underground in at least two key ways. The water levels in rock will determine its electrical conductivity, and thus change the magnitude of the telluric currents induced in the rock by changing magnetic fields generated in the ionosphere. This can be studied by using multiple magnetometers at different underground locations. Secondly the flow of water through rock will generate a small magnetic signal, of unknown magnitude, through the electrokinetic effect. SQUID magnetometry has the potential to allow passive studies of groundwater changes in complex systems such as karst. We have monitored geomagnetic signals using two SQUID magnetometers at the LSBB underground laboratory, and set an initial limit on the magnitude of the electrokinetic signal. We now plan to carry out a longer term measurement using three SQUID systems as well as fluxgate sensors to track changes in the gradient of the magnetic field across the underground complex.

  12. Magnetometer-enhanced personal locator for tunnels and GPS-denied outdoor environments

    Science.gov (United States)

    Kwanmuang, Surat; Ojeda, Lauro; Borenstein, Johann

    2011-06-01

    This paper describes recent advances with our earlier developed Personal Dead-reckoning (PDR) system for GPS-denied environments. The PDR system uses a foot-mounted Inertial Measurement Unit (IMU) that also houses a three axismagnetometer. In earlier work we developed methods for correcting the drift errors in the accelerometers, thereby allowing very accurate measurements of distance traveled. In addition, we developed a powerful heuristic method for correcting heading errors caused by gyro drift. The heuristics exploit the rectilinear features found in almost all manmade structures and therefore limit this technology to indoor use only. Most recently we integrated a three-axis magnetometer with the IMU, using a Kalman Filter. While it is well known that the ubiquitous magnetic disturbances found in most modern buildings render magnetometers almost completely useless indoors, these sensors are nonetheless very effective in pristine outdoor environments as well as in some tunnels and caves. The present paper describes the integrated magnetometer/IMU system and presents detailed experimental results. Specifically, the paper reports results of an objective test conducted by Firefighters of California's CAL-FIRE. In this particular test, two firefighters in full operational gear and one civilian hiked up a two-mile long mountain trail over rocky, sometimes steeply inclined terrain, each wearing one of our magnetometer-enhanced PDR systems but not using any GPS. During the hour-long hike the average position error was about 20 meters and the maximum error was less than 45 meters, which is about 1.4% of distance traveled for all three PDR systems.

  13. Integrated high-transition temperature magnetometer with only two superconducting layers

    DEFF Research Database (Denmark)

    Kromann, R.; Kingston, J.J.; Miklich, A.H.

    1993-01-01

    are required, the SQUID body serving as the crossunder that completes the multiturn flux transformer. The highest temperature at which any of the magnetometers functioned was 76 K. At 60 K the magnetic field gain of this device was 63, and the magnetic field noise was 160 fT Hz-1/2 at 2 kHz, increasing to 3.4...... pT Hz-1/2 at 1 Hz....

  14. Accelerometer and Magnetometer Based Gyroscope Emulation on Smart Sensor for a Virtual Reality Application

    Directory of Open Access Journals (Sweden)

    Baptiste Delporte

    2012-03-01

    Full Text Available In this paper, we propose two methods based on quaternions to compute the angles of inclination and the angular velocity with 6 degrees of freedom using the measurements of a 3-axis accelerometer and a 3-axis magnetometer. Each method has singularities which occur during the computation of the orientation of the device in the 3-dimensional space. We propose solutions to avoid these singularities. Experimental results are given to compare our model with a real gyroscope.

  15. Diurnal and Seasonal Variations in Mid-Latitude Geomagnetic Field During International Quiet Days: BOH Magnetometer

    Directory of Open Access Journals (Sweden)

    Junga Hwang

    2012-12-01

    Full Text Available Korea Astronomy and Space Science Institute researchers have installed and operated magnetometers at Bohyunsan Observatory to measure the Earth's magnetic field variations in South Korea. In 2007, we installed a fluxgate magnetometer (RFP-523C to measure H, D, and Z components of the geomagnetic field. In addition, in 2009, we installed a Overhauser proton sensor to measure the absolute total magnetic field F and a three-axis magneto-impedance sensor for spectrum analysis. Currently three types of magnetometer data have been accumulated. In this paper, we use the H, D, Z components of fluxgate magnetometer data to investigate the characteristics of mid-latitude geomagnetic field variation. To remove the temporary changes in Earth’s geomagnetic filed by space weather, we use the international quiet days’ data only. In other words, we performed a superposed epoch analysis using five days per each month during 2008-2011. We find that daily variations of H, D, and Z shows similar tendency compared to previous results using all days. That is, H, D, Z all three components’ quiet intervals terminate near the sunrise and shows maximum 2-3 hours after the culmination and the quiet interval start from near the sunset. Seasonal variations show similar dependences to the Sun. As it becomes hot season, the geomagnetic field variation’s amplitude becomes large and the quiet interval becomes shortened. It is well-known that these variations are effects of Sq current system in the Earth’s atmosphere. We confirm that the typical mid-latitude geomagnetic field variations due to the Sq current system by excluding all possible association with the space weather.

  16. Magnetometer instrument team studies for the definition phase of the outer planets grand tour

    Science.gov (United States)

    Coleman, P. J., Jr.

    1973-01-01

    The work performed by the magnetic fields investigation team during the mission definition phases of the Outer Planets Grand Tour (OPGT) and the Mariner Jupiter Saturn (MJS) Missions is reported. This work involved three tasks: (1) defining the objectives of the magnetic fields investigations, (2) defining the magnetometer systems required to meet these objectives, and (3) developing and testing hardware elements in certain mission-specific areas.

  17. Identification of Mobile Phones Using the Built-In Magnetometers Stimulated by Motion Patterns.

    Science.gov (United States)

    Baldini, Gianmarco; Dimc, Franc; Kamnik, Roman; Steri, Gary; Giuliani, Raimondo; Gentile, Claudio

    2017-04-06

    We investigate the identification of mobile phones through their built-in magnetometers. These electronic components have started to be widely deployed in mass market phones in recent years, and they can be exploited to uniquely identify mobile phones due their physical differences, which appear in the digital output generated by them. This is similar to approaches reported in the literature for other components of the mobile phone, including the digital camera, the microphones or their RF transmission components. In this paper, the identification is performed through an inexpensive device made up of a platform that rotates the mobile phone under test and a fixed magnet positioned on the edge of the rotating platform. When the mobile phone passes in front of the fixed magnet, the built-in magnetometer is stimulated, and its digital output is recorded and analyzed. For each mobile phone, the experiment is repeated over six different days to ensure consistency in the results. A total of 10 phones of different brands and models or of the same model were used in our experiment. The digital output from the magnetometers is synchronized and correlated, and statistical features are extracted to generate a fingerprint of the built-in magnetometer and, consequently, of the mobile phone. A SVM machine learning algorithm is used to classify the mobile phones on the basis of the extracted statistical features. Our results show that inter-model classification (i.e., different models and brands classification) is possible with great accuracy, but intra-model (i.e., phones with different serial numbers and same model) classification is more challenging, the resulting accuracy being just slightly above random choice.

  18. CubeSat attitude estimation via AUKF using magnetometer measurements and MRPs.

    OpenAIRE

    Sanfedino, Francesco; Scardino, Marco; Chaix, Jeremie; Lizy-Destrez, Stéphanie

    2015-01-01

    In this article the Attitude and Control system of a CubeSat is presented. The attitude estimation design approach used is based on Adaptative Unscented Kalman Filter (AUKF) using three-axis magnetometer measurements. A set of modified Rodrigues Parameters (MRPs) is used to evaluate the attitude. Finally in order to have an complete ADCS system two control laws are introduced (Bdot and Sliding Mode) to best simulate a real CubeSat mission. The first one allows the spacecraft the cont...

  19. Determination of the plasmapause boundary using ground magnetometer field line resonances, satellite observations, and modeling

    Science.gov (United States)

    Zesta, E.; Boudouridis, A.; Jorgensen, A. M.; Yizengaw, E.; Chi, P. J.; Moldwin, M.; Carranza, T.; Mann, I. R.; Johnston, W. R.; Wilson, G. R.

    2012-12-01

    The plasmapause boundary layer (PBL) separates the cold and dense plasmaspheric plasma from the more tenuous and hot plasma sheet plasma and organizes the spatial distribution of ULF and VLF waves that can contribute to acceleration or loss processes of radiation belt particles through wave-particle interactions. The PBL has been traditionally determined by in situ observations and can be given by empirical models. Recent work has shown that a mid-latitude chain of well-spaced ground magnetometers can also determine the PBL boundary location. Spectral properties, like the cross-phase reversal between two stations closely aligned in latitude, have been shown to indicate the presence of a sharp PBL. We show here an example of such a PBL identification during the moderate storm of Nov 9-12, 2006. We combine observations from the SAMBA (South American Meridional B-field Array), MEASURE (Magnetometers along the Eastern Atlantic Seaboard for Undergraduate Research and Education), McMAC (Mid-continent Magnetoseismic Chain), and CARISMA ground magnetometer chains covering L values from L=2 to L=5 to statistically determine how commonly the PBL is determined from ground magnetometers. In our initial study we examine observations from June to December, 2006. We compare our PBL determinations with the determination of the same boundary from the Defense Meteorological Satellite Program (DMSP) satellites, based on the H+ density observations, which have been shown to accurately identify the PBL from a low-Earth orbiting satellite. We also compare our PBL identification with those determined from a global GPS TEC map and GPS TEC tomography technique used by a chain of ground GPS receivers. Finally, we compare our observations with results from the Dynamic Global Core Plasma Model (DGCPM), as well as existing empirical models based on in situ observations.

  20. Evaluation of High-resolution Geomagnetic Field Observation System Using HTS-SQUID Magnetometer and its Application.

    Science.gov (United States)

    Katori, Y.; Okubo, K.; Hato, T.; Tsukamoto, A.; Tanabe, K.; Onishi, N.; Furukawa; Isogami, S.; Takeuchi, N.

    2014-12-01

    Magnetic field changes associated with earthquakes have been investigated previously (1964 Stacey, 1994 Johnston et al.). Our research group also reported successful observation of "co-faulting" Earth's magnetic field changes due to piezomagnetic effects caused by earthquake rupturing in 2008 Iwate-Miyagi Nairiku earthquake of M7.2 (2011 Okubo et al.) using optoelectronic observation system with flux-gate magnetometers. This is an important finding; the electromagnetic fields originating from such sources satisfy the Maxwell equations and hence they propagate from the sources to the observation site at a speed of light in the crustal materials. Further efforts could lead us to a new system for super-early warning of destructive earthquakes with the magnetic measurements. On the other hand, the observed result in 2008 Iwate-Miyagi Nairiku earthquake was suggested that the geomagnetic variation signal accompanying fault movement, whose sources are the piezomagnetic effects, is very small; therefore development of a high-sensitive magnetometer system is very important. To solve this problem, we introduce long-term precise geomagnetic observations using high-temperature-superconductor based superconducting-quantum-interference-device (HTS-SQUID) magnetometer system. That is, our research group developed the HTS-SQUID magnetometer system for high-resolution observation of Earth's magnetic field. Since March 2012, we have observed the geomagnetic field using a HTS-SQUID magnetometer at Iwaki observation site (IWK) in Fukushima, Japan. The sampling interval of the magnetometer is 0.04 sec. The observation clock has been synchronized by use of GPS signals. An accelerometer is also installed at observation point. Additionally, in the next stage, we develop the HTS- SQUID magnetometer system Unit No.2 (mark II). In the present study, we show the results observed by our HTS-SQUID magnetometer system and make an evaluation of our geomagnetic field observation system.

  1. Implementation of a Data Handling System for a Scientific  Magnetometer on a CubeSat

    OpenAIRE

    Stana, Theodor-Adrian

    2012-01-01

    Since their invention in 1999, CubeSats have become a widespread standard for small picosatellite missions. CubeSats allow for quick development of satellite payloads and launch in space without the high costs of a normal satellite. Emphasis during the CubeSat design process is placed on use of commercialoff- the-shelf (COTS) components and reuse of previously-designed units. This report describes the interfacing of a scientific magnetometer, the Small Magnetometer in Low-Mass Experiment (SMI...

  2. Tracking geomagnetic fluctuations to picotesla accuracy using two superconducting quantum interference device vector magnetometers.

    Science.gov (United States)

    Henry, S; Pozzo di Borgo, E; Cavaillou, A

    2013-02-01

    SQUIDs can be used to monitor the three vector components of the geomagnetic field to a high precision at very low frequencies, yet as they are susceptible to external interference, the accuracy to which they can track changes in the dc field over long periods has been unclear. We have carried out simultaneous measurements of the geomagnetic field recorded using two independent 3-axis SQUID magnetometers at the Laboratoire Souterrain à Bas Bruit (LSBB). We demonstrate a technique to take the difference between a linear transform of the three signals from one magnetometer, and a reference signal from the other, in order to account for any difference in alignment and calibration, and track local signals at a sub-nT level. We confirmed that both systems tracked the same signal with an RMS difference as low as 56pT over a period of 72 h. To our knowledge this is the first such demonstration of the long term accuracy of SQUID magnetometers for monitoring geomagnetic fields.

  3. MgB{sub 2} magnetometer with a directly coupled pick-up loop

    Energy Technology Data Exchange (ETDEWEB)

    Portesi, C [Istituto Elettrotecnico Nazionale Galileo Ferraris, Strada delle Cacce 91, I-10135 Turin (Italy); Mijatovic, D [Low Temperature Division and Mesa Research Institute, University of Twente, PO Box 217, 7500 AE Enschede (Netherlands); Veldhuis, D [Low Temperature Division and Mesa Research Institute, University of Twente, PO Box 217, 7500 AE Enschede (Netherlands); Brinkman, A [Low Temperature Division and Mesa Research Institute, University of Twente, PO Box 217, 7500 AE Enschede (Netherlands); Monticone, E [Istituto Elettrotecnico Nazionale Galileo Ferraris, Strada delle Cacce 91, I-10135 Turin (Italy); Gonnelli, R S [INFM, Dipartimento di Fisica, Politecnico di Torino, Corso Duca degli Abruzzi 24, I-10129 Turin (Italy)

    2006-05-15

    In this work, we show the results obtained in the fabrication and characterization of an MgB{sub 2} magnetometer with a directly coupled pick-up loop. We used an all in situ technique for fabricating magnesium diboride films, which consists of the co-evaporation of B and Mg by means of an e-gun and a resistive heater respectively. Consequently, we realized the superconducting device, which incorporates two nanobridges as weak links in a superconducting loop. The nanobridges were realized by focused ion beam milling; they were 240 nm wide and had a critical current density of 10{sup 7} A cm{sup -2}. The magnetometer was characterized at different temperatures and also measurements of the noise levels have been performed. The device shows Josephson quantum interference up to 20 K and the calculated effective area at low temperatures was 0.24 mm{sup 2}. The transport properties of the magnetometer allow determining fundamental materials properties of the MgB{sub 2} thin films, such as the penetration depth.

  4. Study on modulation amplitude stabilization method for PEM based on FPGA in atomic magnetometer

    Science.gov (United States)

    Wang, Qinghua; Quan, Wei; Duan, Lihong

    2017-10-01

    Atomic magnetometer which uses atoms as sensitive elements have ultra-high precision and has wide applications in scientific researches. The photoelastic modulation method based on photoelastic modulator (PEM) is used in the atomic magnetometer to detect the small optical rotation angle of a linearly polarized light. However, the modulation amplitude of the PEM will drift due to the environmental factors, which reduces the precision and long-term stability of the atomic magnetometer. Consequently, stabilizing the PEM's modulation amplitude is essential to precision measurement. In this paper, a modulation amplitude stabilization method for PEM based on Field Programmable Gate Array (FPGA) is proposed. The designed control system contains an optical setup and an electrical part. The optical setup is used to measure the PEM's modulation amplitude. The FPGA chip, with the PID control algorithm implemented in it, is used as the electrical part's micro controller. The closed loop control method based on the photoelastic modulation detection system can directly measure the PEM's modulation amplitude in real time, without increasing the additional optical devices. In addition, the operating speed of the modulation amplitude stabilization control system can be greatly improved because of the FPGA's parallel computing feature, and the PID control algorithm ensures flexibility to meet different needs of the PEM's modulation amplitude set values. The Modelsim simulation results show the correctness of the PID control algorithm, and the long-term stability of the PEM's modulation amplitude reaches 0.35% in a 3-hour continuous measurement.

  5. The MAGIC of CINEMA: first in-flight science results from a miniaturised anisotropic magnetoresistive magnetometer

    Directory of Open Access Journals (Sweden)

    M. O. Archer

    2015-06-01

    Full Text Available We present the first in-flight results from a novel miniaturised anisotropic magnetoresistive space magnetometer, MAGIC (MAGnetometer from Imperial College, aboard the first CINEMA (CubeSat for Ions, Neutrals, Electrons and MAgnetic fields spacecraft in low Earth orbit. An attitude-independent calibration technique is detailed using the International Geomagnetic Reference Field (IGRF, which is temperature dependent in the case of the outboard sensor. We show that the sensors accurately measure the expected absolute field to within 2% in attitude mode and 1% in science mode. Using a simple method we are able to estimate the spacecraft's attitude using the magnetometer only, thus characterising CINEMA's spin, precession and nutation. Finally, we show that the outboard sensor is capable of detecting transient physical signals with amplitudes of ~ 20–60 nT. These include field-aligned currents at the auroral oval, qualitatively similar to previous observations, which agree in location with measurements from the DMSP (Defense Meteorological Satellite Program and POES (Polar-orbiting Operational Environmental Satellites spacecraft. Thus, we demonstrate and discuss the potential science capabilities of the MAGIC instrument onboard a CubeSat platform.

  6. The MAGIC of CINEMA: first in-flight science results from a miniaturised anisotropic magnetoresistive magnetometer

    Science.gov (United States)

    Archer, M. O.; Horbury, T. S.; Brown, P.; Eastwood, J. P.; Oddy, T. M.; Whiteside, B. J.; Sample, J. G.

    2015-06-01

    We present the first in-flight results from a novel miniaturised anisotropic magnetoresistive space magnetometer, MAGIC (MAGnetometer from Imperial College), aboard the first CINEMA (CubeSat for Ions, Neutrals, Electrons and MAgnetic fields) spacecraft in low Earth orbit. An attitude-independent calibration technique is detailed using the International Geomagnetic Reference Field (IGRF), which is temperature dependent in the case of the outboard sensor. We show that the sensors accurately measure the expected absolute field to within 2% in attitude mode and 1% in science mode. Using a simple method we are able to estimate the spacecraft's attitude using the magnetometer only, thus characterising CINEMA's spin, precession and nutation. Finally, we show that the outboard sensor is capable of detecting transient physical signals with amplitudes of ~ 20-60 nT. These include field-aligned currents at the auroral oval, qualitatively similar to previous observations, which agree in location with measurements from the DMSP (Defense Meteorological Satellite Program) and POES (Polar-orbiting Operational Environmental Satellites) spacecraft. Thus, we demonstrate and discuss the potential science capabilities of the MAGIC instrument onboard a CubeSat platform.

  7. Attitude-independent magnetometer calibration for marine magnetic surveys: regularization issue

    International Nuclear Information System (INIS)

    Wu, Zhitian; Hu, Xiaoping; Wu, Meiping; Cao, Juliang

    2013-01-01

    We have developed an attitude-independent calibration method for a shipboard magnetometer to estimate the absolute strength of the geomagnetic field from a marine vessel. The three-axis magnetometer to be calibrated is fixed on a rigid aluminium boom ahead of the vessel to reduce the magnetic effect of the vessel. Due to the constrained manoeuvres of the vessel, a linear observational equation system for calibration parameter estimation is severely ill-posed. Consequently, if the issue is not mitigated, traditional calibration methods may result in unreliable or unsuccessful solutions. In this paper, the ill-posed problem is solved by using the truncated total least squares (TTLS) technique. This method takes advantage of simultaneously considering errors on both sides of the observation equation. Furthermore, the TTLS method suits strongly ill-posed problems. Simulations and experiments have been performed to assess the performance of the TTLS method and to compare it with the performance of conventional regularization approaches such as the Tikhonov method and truncated single value decomposition. The results show that the proposed algorithm can effectively mitigate the ill-posed problem and is more stable than the compared regularization methods for magnetometer calibration applications. (paper)

  8. State-to-state reactive differential cross sections for the H +H2→H2+H reaction on five different potential energy surfaces employing a new quantum wavepacket computer code: DIFFREALWAVE

    Science.gov (United States)

    Hankel, Marlies; Smith, Sean C.; Allan, Robert J.; Gray, Stephen K.; Balint-Kurti, Gabriel G.

    2006-10-01

    State-to-state differential cross sections have been calculated for the hydrogen exchange reaction, H +H2→H2+H, using five different high quality potential energy surfaces with the objective of examining the sensitivity of these detailed cross sections to the underlying potential energy surfaces. The calculations were performed using a new parallel computer code, DIFFREALWAVE. The code is based on the real wavepacket approach of Gray and Balint-Kurti [J. Chem. Phys. 108, 950 (1998)]. The calculations are parallelized over the helicity quantum number Ω' (i.e., the quantum number for the body-fixed z component of the total angular momentum) and wavepackets for each J,Ω' set are assigned to different processors, similar in spirit to the Coriolis-coupled processors approach of Goldfield and Gray [Comput. Phys. Commun. 84, 1 (1996)]. Calculations for J =0-24 have been performed to obtain converged state-to-state differential cross sections in the energy range from 0.4to1.2eV. The calculations employ five different potential energy surfaces, the BKMP2 surface and a hierarchical family of four new ab initio surfaces [S. L. Mielke, et al., J. Chem. Phys. 116, 4142 (2002)]. This family of four surfaces has been calculated using three different hierarchical sets of basis functions and also an extrapolation to the complete basis set limit, the so called CCI surface. The CCI surface is the most accurate surface for the H3 system reported to date. Our calculations of differential cross sections are the first to be reported for the A2, A3, A4, and CCI surfaces. They show that there are some small differences in the cross sections obtained from the five different surfaces, particularly at higher energies. The calculations also show that the BKMP2 performs well and gives cross sections in very good agreement with the results from the CCI surface, displaying only small divergences at higher energies.

  9. Optimizations of spin-exchange relaxation-free magnetometer based on potassium and rubidium hybrid optical pumping

    Energy Technology Data Exchange (ETDEWEB)

    Fang, Jiancheng; Wang, Tao, E-mail: wangtao@buaa.edu.cn; Li, Yang [School of Instrument Science and Opto-Electronics Engineering, Beihang University, Beijing 100191 (China); Zhang, Hong; Zou, Sheng [School of Instrument Science and Engineering, Southeast University, Nanjing 210096 (China)

    2014-12-15

    The hybrid optical pumping atomic magnetometers have not realized its theoretical sensitivity, the optimization is critical for optimal performance. The optimizations proposed in this paper are suitable for hybrid optical pumping atomic magnetometer, which contains two alkali species. To optimize the parameters, the dynamic equations of spin evolution with two alkali species were solved, whose steady-state solution is used to optimize the parameters. The demand of the power of the pump beam is large for hybrid optical pumping. Moreover, the sensitivity of the hybrid optical pumping magnetometer increases with the increase of the power density of the pump beam. The density ratio between the two alkali species is especially important for hybrid optical pumping magnetometer. A simple expression for optimizing the density ratio is proposed in this paper, which can help to determine the mole faction of the alkali atoms in fabricating the hybrid cell before the cell is sealed. The spin-exchange rate between the two alkali species is proportional to the saturated density of the alkali vapor, which is highly dependent on the temperature of the cell. Consequently, the sensitivity of the hybrid optical pumping magnetometer is dependent on the temperature of the cell. We proposed the thermal optimization of the hybrid cell for a hybrid optical pumping magnetometer, which can improve the sensitivity especially when the power of the pump beam is low. With these optimizations, a sensitivity of approximately 5 fT/Hz{sup 1/2} is achieved with gradiometer arrangement.

  10. Optimizations of spin-exchange relaxation-free magnetometer based on potassium and rubidium hybrid optical pumping

    International Nuclear Information System (INIS)

    Fang, Jiancheng; Wang, Tao; Li, Yang; Zhang, Hong; Zou, Sheng

    2014-01-01

    The hybrid optical pumping atomic magnetometers have not realized its theoretical sensitivity, the optimization is critical for optimal performance. The optimizations proposed in this paper are suitable for hybrid optical pumping atomic magnetometer, which contains two alkali species. To optimize the parameters, the dynamic equations of spin evolution with two alkali species were solved, whose steady-state solution is used to optimize the parameters. The demand of the power of the pump beam is large for hybrid optical pumping. Moreover, the sensitivity of the hybrid optical pumping magnetometer increases with the increase of the power density of the pump beam. The density ratio between the two alkali species is especially important for hybrid optical pumping magnetometer. A simple expression for optimizing the density ratio is proposed in this paper, which can help to determine the mole faction of the alkali atoms in fabricating the hybrid cell before the cell is sealed. The spin-exchange rate between the two alkali species is proportional to the saturated density of the alkali vapor, which is highly dependent on the temperature of the cell. Consequently, the sensitivity of the hybrid optical pumping magnetometer is dependent on the temperature of the cell. We proposed the thermal optimization of the hybrid cell for a hybrid optical pumping magnetometer, which can improve the sensitivity especially when the power of the pump beam is low. With these optimizations, a sensitivity of approximately 5 fT/Hz 1/2 is achieved with gradiometer arrangement

  11. The QuakeFinder Magnetometer Network - a Platform for Earth and Space Science Research

    Science.gov (United States)

    Bleier, T.; Kappler, K. N.; Schneider, D.

    2016-12-01

    QuakeFinder (QF) is a humanitarian research and development project attempting to characterize earth-emitting electromagnetic (EM) signals as potential precursors to earthquakes. Beginning in 2005, QF designed, built, deployed and now maintains an array of 165 remote monitoring stations in 6 countries (US/California, Taiwan, Greece, Indonesia, Peru and Chile). Having amassed approximately 70 TB of data and greater than 140 earthquakes (M4+), QF is focused on the data analysis and signal processing algorithms in our effort to enable a forecasting capability. QF's autonomous stations, located along major fault lines, collect and transmit electromagnetic readings from 3-axis induction magnetometers and positive/negative ion sensors, a geophone, as well as various station health status and local conditions. The induction magnetometers, oriented N-S,E-W and vertically, have a 40 nT range and 1 pT sensitivity. Data is continuously collected at 50 samples/sec (sps), GPS time-stamped and transmitted, primarily through cell phone networks, to our data center in Palo Alto, California. The induction magnetometers routinely detect subtle geomagnetic and ionospheric disturbances as observed worldwide. QF seeks to make available both historic data and the array platform to strategic partners in the EM-related research and operation fields. The QF system will be described in detail with examples of local and regional geomagnetic activity. The stations are robust and will be undergoing a system-level upgrade in the near future. Domestically, QF maintains a 98% `up time' among the 120 stations in California while internationally our metric is typically near 80%. Irregular cell phone reception is chief among the reasons for outages although little data has been lost as the stations can store up to 90 days of data. These data are retrieved by QF personnel or, when communication is reestablished, the QF data ingest process automatically updates the database. Planned station upgrades

  12. Magnetometer Data in the Classroom as a part of the NASA THEMIS Satellite Mission

    Science.gov (United States)

    Peticolas, L. M.; Bean, J.; Walker, A.

    2011-12-01

    The NASA-funded THEMIS mission was designed to determine the onset time and location of magnetic substorms of Earth's space environment, a prerequisite to understanding space weather. THEMIS is an acronym for Time History of Events and Macroscale Interactions during Substorms. he Geomagnetic Event Observation Network by Students (GEONS) project was the flagship, formal education component of the E/PO program. With the placement of magnetometers in the proximity of rural schools throughout the country, middle and high school teachers along with their students benefited from the opportunity to work with 'real-time' data and participated in hands-on space science activities. Particular attention was paid to placing the magnetometer stations at schools in rural communities whose students were traditionally underserved and underrepresented in the sciences. The project offered to the teachers of these students long-term professional development opportunities that centered around THEMIS-related space science and the magnetometer data. The THEMIS E/PO final evaluation report for the main phase of the THEMIS mission covered the period from 2003-2009, describing the impact of this program such as this program placed magnetometers sites at 13 rural, underserved schools/communities, two-fifths of which are on tribal lands; and provided intensive professional development for 20 teachers from 2004 through 2009. A core group of eight teachers estimated reaching more than 2,720 students with THEMIS-related materials/ideas. 75% of these students are minorities in science. Core teachers provided evidence of the project's positive impact on students' attitudes toward science and their choices for courses that position them for STEM-related careers. Core teachers reported sharing THEMIS-related materials/ideas with 275 colleagues. The NewsHour with Jim Lehrer featured the Petersburg, Alaska site potentially reaching more than 5 million viewers in two airings, according to Nielsen

  13. Terrestrial analogues models based on MOURA magnetometer data. Application to Gusev crater and Apollinaris volcano

    Science.gov (United States)

    Díaz-Michelena, Marina; Cerdán, Miguel Felipe; Ramírez-Nicolás, María; Sánchez-Cano, Beatríz; Sánchez-Bayton, Marina; Kilian, Rolf

    2014-05-01

    Sometimes it is a problem to determine whether a crater was formed by an explosive volcanic event or a meteorite impact. This issue is of interest even on Earth where geological features are often masked by erosion or vegetation and for the interpretation of ancient craters on other planets or moons, where the geological context is not clearly determined. Thus we propose a geophysical modelling approach to study the formation of such craters with potential application to Mars, whose surface is fully covered with craters. The evolution of this study might shed more light over the martian ancient geodynamo. The Earth provides many examples to develop models for the geological features of such craters since it is feasible to perform magnetic and gravity surveys at different altitudes, and therefore to have information on different surface scales. The models developed with real satellite, airborne and on ground data on Earth (Moar, 2004) can be extrapolated to other bodies, like Mars or the Moon, where only satellite and limited ground data are available. In the present study, surveys are mainly based on vector data from surveys with MOURA magnetometer developed by INTA for Mars MetNet mission. Since the ambient conditions of Mars are so extreme, MOURA is capable to withstand the extreme conditions of the terrestrial analogues. The models of craters are based on typical crater structures proposed by Lorenz (2003) and Grieve (2006), where distinct susceptibilities and remanent magnetization have been attributed to different volcanic or impact related rock units (bedded upper diatreme facies and unbedded lower diatreme facies, tephra rims and ejecta blankets, high pressures and temperature volumes, etc) and target rocks. The analysis of the scalar magnetic potential and its harmonics can help in the interpretation of the origin of these craters and their geological context by means of the magnetic signature. In this study, it will be presented the correlation between

  14. Robust pre-specified time synchronization of chaotic systems by employing time-varying switching surfaces in the sliding mode control scheme

    Science.gov (United States)

    Khanzadeh, Alireza; Pourgholi, Mahdi

    2016-08-01

    In the conventional chaos synchronization methods, the time at which two chaotic systems are synchronized, is usually unknown and depends on initial conditions. In this work based on Lyapunov stability theory a sliding mode controller with time-varying switching surfaces is proposed to achieve chaos synchronization at a pre-specified time for the first time. The proposed controller is able to synchronize chaotic systems precisely at any time when we want. Moreover, by choosing the time-varying switching surfaces in a way that the reaching phase is eliminated, the synchronization becomes robust to uncertainties and exogenous disturbances. Simulation results are presented to show the effectiveness of the proposed method of stabilizing and synchronizing chaotic systems with complete robustness to uncertainty and disturbances exactly at a pre-specified time.

  15. Robust pre-specified time synchronization of chaotic systems by employing time-varying switching surfaces in the sliding mode control scheme

    International Nuclear Information System (INIS)

    Khanzadeh, Alireza; Pourgholi, Mahdi

    2016-01-01

    In the conventional chaos synchronization methods, the time at which two chaotic systems are synchronized, is usually unknown and depends on initial conditions. In this work based on Lyapunov stability theory a sliding mode controller with time-varying switching surfaces is proposed to achieve chaos synchronization at a pre-specified time for the first time. The proposed controller is able to synchronize chaotic systems precisely at any time when we want. Moreover, by choosing the time-varying switching surfaces in a way that the reaching phase is eliminated, the synchronization becomes robust to uncertainties and exogenous disturbances. Simulation results are presented to show the effectiveness of the proposed method of stabilizing and synchronizing chaotic systems with complete robustness to uncertainty and disturbances exactly at a pre-specified time. (paper)

  16. A Near-real-time Data Transport System for Selected Stations in the Magnetometer Array for Cusp and Cleft Studies (MACCS)

    Science.gov (United States)

    Engebretson, M. J.; Valentic, T. A.; Stehle, R. H.; Hughes, W. J.

    2004-05-01

    The Magnetometer Array for Cusp and Cleft Studies (MACCS) is a two-dimensional array of eight fluxgate magnetometers that was established in 1992-1993 in the Eastern Canadian Arctic from 75° to over 80° MLAT to study electrodynamic interactions between the solar wind and Earth's magnetosphere and high-latitude ionosphere. A ninth site in Nain, Labrador, extends coverage down to 66° between existing Canadian and Greenland stations. Originally designed as part of NSF's GEM (Geospace Environment Modeling) Program, MACCS has contributed to the study of transients and waves at the magnetospheric boundary and in the near-cusp region as well as to large, cooperative, studies of ionospheric convection and substorm processes. Because of the limitations of existing telephone lines to each site, it has not been possible to economically access MACCS data promptly; instead, each month's collected data is recorded and mailed to the U.S. for processing and eventual posting on a publicly-accessible web site, http://space.augsburg.edu/space. As part of its recently renewed funding, NSF has supported the development of a near-real-time data transport system using the Iridium satellite network, which will be implemented at two MACCS sites in summer 2004. At the core of the new MACCS communications system is the Data Transport Network, software developed with NSF-ITR funding to automate the transfer of scientific data from remote field stations over unreliable, bandwidth-constrained network connections. The system utilizes a store-and-forward architecture based on sending data files as attachments to Usenet messages. This scheme not only isolates the instruments from network outages, but also provides a consistent framework for organizing and accessing multiple data feeds. Client programs are able to subscribe to data feeds to perform tasks such as system health monitoring, data processing, web page updates and e-mail alerts. The MACCS sites will employ the Data Transport Network

  17. Employers' Guide to the Employment Equity Act

    Directory of Open Access Journals (Sweden)

    Lesley-Anne Katz

    2001-12-01

    Full Text Available Employers' Guide to the Employment Equity Act is aimed, according to the author, at assisting those in the labour arena (employers, managers, labour relations practitioners, union officials, and students to develop a practical understanding of the Employment Equity Act (hereafter, the Act.

  18. Direct detection of additives and degradation products from polymers by liquid extraction surface analysis employing chip-based nanospray mass spectrometry.

    Science.gov (United States)

    Paine, Martin R L; Barker, Philip J; Maclauglin, Shane A; Mitchell, Todd W; Blanksby, Stephen J

    2012-02-29

    Polymer-based surface coatings in outdoor applications experience accelerated degradation due to exposure to solar radiation, oxygen and atmospheric pollutants. These deleterious agents cause undesirable changes to the aesthetic and mechanical properties of the polymer, reducing its lifetime. The use of antioxidants such as hindered amine light stabilisers (HALS) retards these degradative processes; however, mechanisms for HALS action and polymer degradation are poorly understood. Detection of the HALS TINUVIN®123 (bis(1-octyloxy-2,2,6,6-tetramethyl-4-piperidyl) sebacate) and the polymer degradation products directly from a polyester-based coil coating was achieved by liquid extraction surface analysis (LESA) coupled to a triple quadrupole QTRAP® 5500 mass spectrometer. The detection of TINUVIN®123 and melamine was confirmed by the characteristic fragmentation pattern observed in LESA-MS/MS spectra that was identical to that reported for authentic samples. Analysis of an unstabilised coil coating by LESA-MS after exposure to 4 years of outdoor field testing revealed the presence of melamine (1,3,5-triazine-2,4,6-triamine) as a polymer degradation product at elevated levels. Changes to the physical appearance of the coil coating, including powder-like deposits on the coating's surface, were observed to coincide with melamine deposits and are indicative of the phenomenon known as polymer 'blooming'. For the first time, in situ detection of analytes from a thermoset polymer coating was accomplished without any sample preparation, providing advantages over traditional extraction-analysis approaches and some contemporary ambient MS methods. Detection of HALS and polymer degradation products such as melamine provides insight into the mechanisms by which degradation occurs and suggests LESA-MS is a powerful new tool for polymer analysis. Copyright © 2012 John Wiley & Sons, Ltd.

  19. Magnetic profiling of the San Andreas Fault using a dual magnetometer UAV aerial survey system.

    Science.gov (United States)

    Abbate, J. A.; Angelopoulos, V.; Masongsong, E. V.; Yang, J.; Medina, H. R.; Moon, S.; Davis, P. M.

    2017-12-01

    Aeromagnetic survey methods using planes are more time-effective than hand-held methods, but can be far more expensive per unit area unless large areas are covered. The availability of low cost UAVs and low cost, lightweight fluxgate magnetometers (FGMs) allows, with proper offset determination and stray fields correction, for low-cost magnetic surveys. Towards that end, we have developed a custom multicopter UAV for magnetic mapping using a dual 3-axis fluxgate magnetometer system: the GEOphysical Drone Enhanced Survey Instrument (GEODESI). A high precision sensor measures the UAV's position and attitude (roll, pitch, and yaw) and is recorded using a custom Arduino data processing system. The two FGMs (in-board and out-board) are placed on two ends of a vertical 1m boom attached to the base of the UAV. The in-board FGM is most sensitive to stray fields from the UAV and its signal is used, after scaling, to clean the signal of the out-board FGM from the vehicle noise. The FGMs record three orthogonal components of the magnetic field in the UAV body coordinates which are then transformed into a north-east-down coordinate system using a rotation matrix determined from the roll-pitch-yaw attitude data. This ensures knowledge of the direction of all three field components enabling us to perform inverse modeling of magnetic anomalies with greater accuracy than total or vertical field measurements used in the past. Field tests were performed at Dragon's Back Pressure Ridge in the Carrizo Plain of California, where there is a known crossing of the San Andreas Fault. Our data and models were compared to previously acquired LiDAR and hand-held magnetometer measurements. Further tests will be carried out to solidify our results and streamline our processing for educational use in the classroom and student field training.

  20. The dynamics of the plasmasphere boundary layer as determined by ground magnetometers, satellite observations, and modeling

    Science.gov (United States)

    Zesta, E.; Boudouridis, A.; Yizengaw, E.; Jorgensen, A. M.; Carranza-fulmer, T. L.; Moldwin, M.; Mann, I. R.; Chi, P. J.

    2013-12-01

    The plasmasphere boundary layer (PBL) separates the cold and dense plasmaspheric plasma from the more tenuous and hot plasma sheet plasma and organizes the spatial distribution of ULF and VLF waves that can contribute to acceleration or loss processes of radiation belt particles through wave-particle interactions. The PBL has been traditionally determined by in situ observations and can be given by empirical models. Recent work has shown that a mid-latitude chain of well-spaced ground magnetometers can also determine the PBL location. Spectral properties, like the cross-phase reversal in the standard field-line resonance (FLR) determination between two stations closely aligned in latitude, have been shown to indicate the presence of a sharp PBL. We merge data from many ground magnetometer pairs from the SAMBA (South American Meridional B-field Array), McMAC (Mid continent Magnetoseismic Chain), and CARISMA (Canadian Array for Realtime Investigations of Magnetic Activity) chains to provide the best available spatial coverage in L values spanning the plasmasphere and PBL, for a range of dynamic states (L=1.6 to greater than 5). The PBL location is identified as the L value of the station pair for which a reverse phase difference is observed in the standard FLR determination. We compare the FLR determined PBL with the trough boundary determined by GPS Total Electron Content (TEC) analysis and with model PBL. Initial results demonstrate that the PBL as identified by the reverse phase differences is in general agreement with TEC identifications and reasonable agreement with models. Reverse Phase Differences are regularly observed at the L range of 2.7 to 3.7 and are highly correlated with Dst and Kp, as determined by daily correlations. We further examine the more detailed time sequence of the PBL dynamics by focusing on key periods around storms preceded by quiet periods, and by using the full L range of the ground magnetometer pairs.

  1. A magnetometer for the cryogen-free systems: extraction and integration method

    International Nuclear Information System (INIS)

    Tripathi, T.S.; Tewari, G.C.; Rastogi, A.K.

    2008-01-01

    We have developed a highly versatile low cost magnetometer that can be attached to the popular cryogen-free helium refrigerator systems for low temperature and high magnetic field measurements. The method of slow extraction of magnetized specimen and precise integration of voltages induced in the pickup coil assembly gives the magnetization. The drawing details of the various parts like extraction unit, pickup coil assembly, high quality integrator circuit and timing circuit will be presented and we shall demonstrate a bench top unit at the conference site. (author)

  2. Airborne gamma-ray spectrometer and magnetometer survey: Aberdeen quadrangle, South Dakota. Final report

    International Nuclear Information System (INIS)

    1981-04-01

    During the months of June through October, 1980, Aero Service Division Western Geophysical Company of America conducted an airborne high sensitivity gamma-ray spectrometer and magnetometer survey over eleven (11) 2 0 x 1 0 NTMS quadrangles located in the states of Minnesota and Wisconsin and seven (7) 2 0 x 1 0 NTMS quadrangles in North and South Dakota. This report discusses the results obtained over the Aberdeen, South Dakota map area. The final data are presented in four different forms: on magnetic tape; on microfiche; in graphic form as profiles and histograms; and in map form as anomaly maps, flight path maps, and computer printer maps

  3. Airborne gamma-ray spectrometer and magnetometer survey, Devils Lake quadrangle, North Dakota. Final report

    International Nuclear Information System (INIS)

    1981-05-01

    During the months of June through October, 1980, Aero Service Division Western Geophysical Company of America conducted an airborne high sensitivity gamma-ray spectrometer and magnetometer survey over eleven (11) 2 0 x 1 0 NTMS quadrangles located in the states of Minnesota and Wisconsin and seven (7) 2 0 x 1 0 NTMS quadrangles in North and South Dakota. This report discusses the results obtained over the Devil's Lake map area of North Dakota. The final data are presented in four different forms: on magnetic tape; on microfiche; in graphic form as profiles and histograms; and in map form as anomaly maps, flight path maps, and computer printer maps

  4. Is light narrowing possible with dense-vapor paraffin coated cells for atomic magnetometers?

    Science.gov (United States)

    Han, Runqi; Balabas, Mikhail; Hovde, Chris; Li, Wenhao; Roig, Hector Masia; Wang, Tao; Wickenbrock, Arne; Zhivun, Elena; You, Zheng; Budker, Dmitry

    2017-12-01

    We investigated the operation of an all-optical rubidium-87 atomic magnetometer with amplitude-modulated light. To study the suppression of spin-exchange relaxation, three schemes of pumping were implemented with room-temperature and heated paraffin coated vacuum cells. Efficient pumping and accumulation of atoms in the F=2 ground state were obtained. However, the sought-for narrowing of the resonance lines has not been achieved. A theoretical analysis of the polarization degree is presented to illustrate the absence of light narrowing due to radiation trapping at high temperature.

  5. Airborne gamma-ray spectrometer and magnetometer survey, Wainwright Quadrangle, Alaska. Final report

    International Nuclear Information System (INIS)

    1981-03-01

    The results obtained from a gamma-ray spectrometer and magnetometer survey over the Wainwright map area of Alaska are presented. Based on the criteria outlined in the general section of interpretation, a total of seven uranium anomalies have been outlined on the interpretation map. With the exception of Anomaly 1, all are located over the higher terrain of the foothills in the southern portion of the quadrangle. All seven anomalies are only weakly to moderately anomalous. There are no indications anywhere within the area of any significant preferential accumulations of uranium. None of the anomalies are thought to be of any economic importance. No follow-up work is recommended

  6. Airborne gamma-ray spectrometer and magnetometer survey, Utukok River Quadrangle, Alaska. Volume I. Final report

    International Nuclear Information System (INIS)

    1981-03-01

    The results obtained from an airborne high sensitivity gamma-ray spectrometer and magnetometer survey over the Utokok River map area of Alaska are presented. Based on the criteria outlined in the general section on interpretation, a total of six uranium anomalies have been outlined on the interpretation map. All of these areas are only weakly to moderately anomalous in uranium and the uranium ratios. None are thought to be indicative of local enrichment of apparent uranium concentrations up to economically significant levels. No follow-up work is recommended

  7. Borrelia recurrentis employs a novel multifunctional surface protein with anti-complement, anti-opsonic and invasive potential to escape innate immunity.

    Directory of Open Access Journals (Sweden)

    Sonja Grosskinsky

    Full Text Available Borrelia recurrentis, the etiologic agent of louse-borne relapsing fever in humans, has evolved strategies, including antigenic variation, to evade immune defence, thereby causing severe diseases with high mortality rates. Here we identify for the first time a multifunctional surface lipoprotein of B. recurrentis, termed HcpA, and demonstrate that it binds human complement regulators, Factor H, CFHR-1, and simultaneously, the host protease plasminogen. Cell surface bound factor H was found to retain its activity and to confer resistance to complement attack. Moreover, ectopic expression of HcpA in a B. burgdorferi B313 strain, deficient in Factor H binding proteins, protected the transformed spirochetes from complement-mediated killing. Furthermore, HcpA-bound plasminogen/plasmin endows B. recurrentis with the potential to resist opsonization and to degrade extracellular matrix components. Together, the present study underscores the high virulence potential of B. recurrentis. The elucidation of the molecular basis underlying the versatile strategies of B. recurrentis to escape innate immunity and to persist in human tissues, including the brain, may help to understand the pathological processes underlying louse-borne relapsing fever.

  8. A High-Sensitivity Tunable Two-Beam Fiber-Coupled High-Density Magnetometer with Laser Heating.

    Science.gov (United States)

    Savukov, Igor; Boshier, Malcolm G

    2016-10-13

    Atomic magnetometers (AM) are finding many applications in biomagnetism, national security, industry, and science. Fiber-coupled (FC) designs promise to make them compact and flexible for operation. Most FC designs are based on a single-beam configuration or electrical heating. Here, we demonstrate a two-beam FC AM with laser heating that has 5 fT/Hz 1/2 sensitivity at low frequency (50 Hz), which is higher than that of other fiber-coupled magnetometers and can be improved to the sub-femtotesla level. This magnetometer is widely tunable from DC to very high frequencies (as high as 100 MHz; the only issue might be the application of a suitable uniform and stable bias field) with a sensitivity under 10 fT/Hz 1/2 and can be used for magneto-encephalography (MEG), magneto-cardiography (MCG), underground communication, ultra-low MRI/NMR, NQR detection, and other applications.

  9. Effects of square-wave magnetic fields on synchronization of nonlinear spin precession for sensitivity improvement of MX magnetometers

    Science.gov (United States)

    Ranjbaran, M.; Tehranchi, M. M.; Hamidi, S. M.; Khalkhali, S. M. H.

    2017-11-01

    Optically pumped atomic magnetometers have found widespread application in biomagnetic studies. Most of the studies utilize MX gradiometers as sensitive and simple arrangements. One the sensitivity improvement methods in the MX configurations is detection of magnetic resonance at higher harmonics due to nonlinear precession of spin polarization. To enhance the harmonic components, we have proposed square wave RF magnetic fields with various duty cycles as substitute for sinusoidal fields. Our results revealed that detection of the 5th harmonic of a 10% duty cycle square wave magnetic field, improved the magnetometer sensitivity by a factor of 4.5 respect to the first harmonic which could be a reliable option to generate high sensitivity MX magnetometers in the MCG applications.

  10. A High-Sensitivity Tunable Two-Beam Fiber-Coupled High-Density Magnetometer with Laser Heating

    Directory of Open Access Journals (Sweden)

    Igor Savukov

    2016-10-01

    Full Text Available Atomic magnetometers (AM are finding many applications in biomagnetism, national security, industry, and science. Fiber-coupled (FC designs promise to make them compact and flexible for operation. Most FC designs are based on a single-beam configuration or electrical heating. Here, we demonstrate a two-beam FC AM with laser heating that has 5 fT/Hz1/2 sensitivity at low frequency (50 Hz, which is higher than that of other fiber-coupled magnetometers and can be improved to the sub-femtotesla level. This magnetometer is widely tunable from DC to very high frequencies (as high as 100 MHz; the only issue might be the application of a suitable uniform and stable bias field with a sensitivity under 10 fT/Hz1/2 and can be used for magneto-encephalography (MEG, magneto-cardiography (MCG, underground communication, ultra-low MRI/NMR, NQR detection, and other applications.

  11. Counter electrojet features in the Brazilian sector: simultaneous observation by radar, digital sounder and magnetometers

    Directory of Open Access Journals (Sweden)

    C. M. Denardini

    2009-04-01

    Full Text Available In the present work we show new results regarding equatorial counter electrojet (CEJ events in the Brazilian sector, based on the RESCO radar, two set of fluxgate magnetometer systems and a digital sounder. RESCO radar is a 50 MHz backscatter coherent radar installed in 1998 at São Luís (SLZ, 2.33° S, 44.60° W, an equatorial site. The Digital sounder routinely monitors the electron density profile at the radar site. The magnetometer systems are fluxgate-type installed at SLZ and Eusébio (EUS, 03.89° S, 38.44° W. From the difference between the horizontal component of magnetic field at SLZ station and the same component at EUS (EEJ ground strength several cases of westward morning electrojet and its normal inversion to the eastward equatorial electrojet (EEJ have been observed. Also, the EEJ ground strength has shown some cases of CEJ events, which been detected with the RESCO radar too. Detection of these events were investigated with respect to their time and height of occurrence, correlation with sporadic E (Es layers at the same time, and their spectral characteristics as well as the radar echo power intensity.

  12. Internal Field of Homogeneously Magnetized Toroid Sensor for Proton Free Precession Magnetometer

    DEFF Research Database (Denmark)

    Primdahl, Fritz; Merayo, José M.G.; Brauer, Peter

    2005-01-01

    The shift of the NMR spectral line frequency in a proton free precession absolute scalar magnetometer using the omni-directional toroid container for a proton-rich liquid depends on the magnetic susceptibility of the liquid and on the direction of the external field relative to the axis of the to......The shift of the NMR spectral line frequency in a proton free precession absolute scalar magnetometer using the omni-directional toroid container for a proton-rich liquid depends on the magnetic susceptibility of the liquid and on the direction of the external field relative to the axis...... of the toroid. The theoretical shift is estimated for water by computing the additional magnetic field from the magnetization of the liquid and comparing it to the theoretical field in a spherical container. Along the axis the estimated average shift is -0.08 nT and perpendicular to the axis the shift is +0.......08 nT relative to that of a spherical sensor. The field inhomogeneity introduced by the toroid shape amounts to 0.32 nT over the volume of the sensor and is not expected to significantly affect the signal decay time, when considering the typical water line width of about 2.5 InT....

  13. Demonstration of the SeptiStrand benthic microbial fuel cell powering a magnetometer for ship detection

    Science.gov (United States)

    Arias-Thode, Y. Meriah; Hsu, Lewis; Anderson, Greg; Babauta, Jerome; Fransham, Roy; Obraztsova, Anna; Tukeman, Gabriel; Chadwick, D. Bart

    2017-07-01

    The Navy has a need for monitoring conditions and gathering information in marine environments. Sensors can monitor and report environmental parameters and potential activities such as animal movements, ships, or personnel. However, there has to be a means to power these sensors. One promising enabling technology that has been shown to provide long-term power production in underwater environments is the benthic microbial fuel cells (BMFC). BMFCs are devices that generate energy by coupling bioanodes and biocathodes through an external energy harvester. Recent studies have demonstrated success for usage of BMFCs in powering small instruments and other devices on the seafloor over limited periods of time. In this effort, a seven-stranded BMFC linear array of 30 m was designed to power a seafloor magnetometer to detect passing ship movements through Pearl Harbor, Hawaii. The BMFC system was connected to a flyback energy harvesting circuit that charged the battery powering the magnetometer. The deployment was demonstrated the BMFC supplied power to the battery for approximately 38 days. This is the first large-scale demonstration system for usage of the SeptiStrand BMFC technology to power a relevant sensor.

  14. Remote sensing of the plasmasphere mass density using ground magnetometers and the FLIP model

    Science.gov (United States)

    Zesta, Eftyhia; Chi, Peter; Moldwin, Mark; Jorgensen, Anders; Richards, Phil; Boudouridis, Athanasios; Duffy, Jared

    2012-07-01

    The SAMBA (South American Meridional B-field Array) chain is a Southern Hemisphere meridional chain of 12 magnetometers, 11 of them at L=1.1 to L=2.5 along the coast of Chile and in the Antarctica peninsula, and one auroral station along the same meridian. SAMBA is ideal for low and mid-latitude studies of geophysical events and ULF waves. The MEASURE (Magnetometers along the Eastern Atlantic Seaboard for Undergraduate Research and Education) and McMAC (Mid-continent Magnetoseismic Chain) chains are Northern Hemisphere meridional chains in the same local time as SAMBA, but cover low to sub-auroral latitudes. SAMBA is partly conjugate to MEASURE and McMAC chains, offering unique opportunities for inter-hemispheric studies. We use 5 of the SAMBA stations and an even larger number of conjugate stations from the Northern hemisphere to determine the field line resonance (FLR) frequency of closely spaced flux tubes in the inner magnetosphere. Standard inversion techniques are used to derive the equatorial mass density of these flux tubes from the FLRs. We thus yield the mass density distribution of the plasmasphere for specific events and compare our results with results from the FLIP thermosphere-ionosphere model model. We find that for moderate activity the model determined FLR radial distribution is in excellent agreement with the observed distribution. During storm time observations indicate stronger depletion than predicted by the model initial runs.

  15. Differential magnetometer method applied to measurement of geomagnetically induced currents in Southern African power networks

    Science.gov (United States)

    Matandirotya, Electdom; Cilliers, Pierre. J.; Van Zyl, Robert R.; Oyedokun, David T.; de Villiers, Jean

    2016-03-01

    Geomagnetically induced currents (GICs) in conductors connected to the Earth are driven by an electric field produced by a time-varying magnetic field linked to magnetospheric-ionospheric current perturbations during geomagnetic storms. The GIC measurements are traditionally done on the neutral-to-ground connections of power transformers. A method of inferring the characteristics of GIC in power lines using differential magnetic field measurements is presented. Measurements of the GIC in the power lines connected to a particular power transformer are valuable in the verification of the modeling of GIC in the power transmission network. The differential magnetometer method (DMM) is an indirect method used to estimate the GIC in a power line. With the DMM, low-frequency GIC in the power line is estimated from the difference between magnetic field recordings made directly underneath the power line and at some distance away, where the magnetic field of the GIC in the transmission line has negligible effect. Results of the first application of the DMM to two selected sites of the Southern African power transmission network are presented. The results show that good quality GIC measurements are achieved through the DMM using Commercially-Off-The-Shelf magnetometers.

  16. Employment specialist competencies for supported employment programs

    NARCIS (Netherlands)

    Corbière, M.; Brouwers, E.P.M.; Lanctôt, N.; van Weeghel, J.

    2014-01-01

    Purpose Supported employment (SE) programs are evidence-based programs offered to people with severe mental illness to facilitate obtaining and keeping competitive work. However, significant variations in individuals’ vocational success may be partly explained by differences in their employment

  17. Development of an optically pumped atomic magnetometer using a K-Rb hybrid cell and its application to magnetocardiography

    Directory of Open Access Journals (Sweden)

    Yosuke Ito

    2012-09-01

    Full Text Available We have developed an optically pumped atomic magnetometer using a hybrid cell of K and Rb. The hybrid optical pumping technique can apply dense alkali-metal vapor to the sensor head and leads to high signal intensity. We use dense Rb vapor as probed atoms, and achieve a sensitivity of approximately 100 fTrms/Hz1/2 around 10 Hz. In this case, the sensitivity is limited by the system noise, and the magnetic linewidth is narrower than that for direct Rb optical pumping. We demonstrated magnetocardiography using the magnetometer and obtained clear human magnetocardiograms.

  18. 49 CFR 1014.140 - Employment.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 8 2010-10-01 2010-10-01 false Employment. 1014.140 Section 1014.140... HANDICAP IN PROGRAMS OR ACTIVITIES CONDUCTED BY THE SURFACE TRANSPORTATION BOARD § 1014.140 Employment. No qualified handicapped person shall, on the basis of handicap, be subjected to discrimination in employment...

  19. Variations of High-Latitude Geomagnetic Pulsation Frequencies: A Comparison of Time-of-Flight Estimates and IMAGE Magnetometer Observations

    Science.gov (United States)

    Sandhu, J. K.; Yeoman, T. K.; James, M. K.; Rae, I. J.; Fear, R. C.

    2018-01-01

    The fundamental eigenfrequencies of standing Alfvén waves on closed geomagnetic field lines are estimated for the region spanning 5.9≤L relatively simplistic mass density model. An assessment of the implications of using different mass density models in the time-of-flight calculations is presented. The calculated frequencies exhibit dependences on field line footprint magnetic latitude and MLT, which are attributed to both magnetic field configuration and spatial variations in mass density. In order to assess the validity of the time-of-flight calculated frequencies, the estimates are compared to observations of FLR (Field Line Resonance) frequencies. Using IMAGE (International Monitor for Auroral Geomagnetic Effects) ground magnetometer observations obtained between 2001 and 2012, an automated FLR identification method is developed, based on the cross-phase technique. The average FLR frequency is determined, including variations with footprint latitude and MLT, and compared to the time-of-flight analysis. The results show agreement in the latitudinal and local time dependences. Furthermore, with the use of the realistic mass density model in the time-of-flight calculations, closer agreement with the observed FLR frequencies is obtained. The study is limited by the latitudinal coverage of the IMAGE magnetometer array, and future work will aim to extend the ground magnetometer data used to include additional magnetometer arrays.

  20. Comparison between SuperDARN flow vectors and equivalent ionospheric currents from ground magnetometer arrays

    DEFF Research Database (Denmark)

    Weygand, J. M.; Amm, O.; Angelopoulos, V.

    2012-01-01

    seasons. This comparison is done over a range of spatial separations, magnetic latitudes, magnetic local times, and auroral electrojet activity to investigate under what conditions the vectors are anti-parallel to one another. Our results show that in general the equivalent ionospheric currents are anti...... that may influence the alignment include ionospheric conductivity gradients and quiet time backgrounds. Our results can be used to approximate the macroscopic (similar to 1000 km) ionospheric convection patterns. The SECS maps represent a value-added product from the raw magnetometer database and can...... be used for contextual interpretation; they can help with our understanding of magnetosphere-ionosphere coupling mechanisms using ground arrays and the magnetospheric spacecraft data, and they can be used as input for other techniques....

  1. Magnetic field `flyby' measurement using a smartphone's magnetometer and accelerometer simultaneously

    Science.gov (United States)

    Monteiro, Martín; Stari, Cecilia; Cabeza, Cecilia; Marti, Arturo C.

    2017-12-01

    The spatial dependence of magnetic fields in simple configurations is a common topic in introductory electromagnetism lessons, both in high school and in university courses. In typical experiments, magnetic fields and distances are obtained taking point-by-point values using a Hall sensor and a ruler, respectively. Here, we show how to take advantage of the smartphone capabilities to get simultaneous measures with the built-in accelerometer and magnetometer and to obtain the spatial dependence of magnetic fields. We consider a simple setup consisting of a smartphone mounted on a track whose direction coincides with the axis of a coil. While the smartphone is moving on the track, both the magnetic field and the distance from the center of the coil (integrated numerically from the acceleration values) are simultaneously obtained. This methodology can easily be extended to more complicated setups.

  2. Nuclear-Spin Gyroscope Based on an Atomic Co-Magnetometer

    Science.gov (United States)

    Romalis, Michael; Komack, Tom; Ghost, Rajat

    2008-01-01

    An experimental nuclear-spin gyroscope is based on an alkali-metal/noblegas co-magnetometer, which automatically cancels the effects of magnetic fields. Whereas the performances of prior nuclear-spin gyroscopes are limited by sensitivity to magnetic fields, this gyroscope is insensitive to magnetic fields and to other external perturbations. In addition, relative to prior nuclear-spin gyroscopes, this one exhibits greater sensitivity to rotation. There is commercial interest in development of small, highly sensitive gyroscopes. The present experimental device could be a prototype for development of nuclear spin gyroscopes suitable for navigation. In comparison with fiber-optic gyroscopes, these gyroscopes would draw less power and would be smaller, lighter, more sensitive, and less costly.

  3. Investigation of a low-cost magneto-inductive magnetometer for space science applications

    Science.gov (United States)

    Regoli, Leonardo H.; Moldwin, Mark B.; Pellioni, Matthew; Bronner, Bret; Hite, Kelsey; Sheinker, Arie; Ponder, Brandon M.

    2018-03-01

    A new sensor for measuring low-amplitude magnetic fields that is ideal for small spacecraft is presented. The novel measurement principle enables the fabrication of a low-cost sensor with low power consumption and with measuring capabilities that are comparable to recent developments for CubeSat applications. The current magnetometer, a software-modified version of a commercial sensor, is capable of detecting fields with amplitudes as low as 8.7 nT at 40 Hz and 2.7 nT at 1 Hz, with a noise floor of 4 pT/Hz at 1 Hz. The sensor has a linear response to less than 3 % over a range of ±100 000 nT. All of these features make the magneto-inductive principle a promising technology for the development of magnetic sensors for both space-borne and ground-based applications to study geomagnetic activity.

  4. Motor Bourn Magnetic Noise Filtering for Magnetometers in Micro-Rotary Aerial Vehicles

    Directory of Open Access Journals (Sweden)

    Nathan J. UNWIN

    2015-10-01

    Full Text Available Avionics systems of micro aerial vehicles (MAV pose unique problems in system design, sensor signal handling and control. This is evident in micro-rotary aircraft as their whole body rotates with the sensors of the flight control. The precise calculation of attitude and heading from magnetometer readings is complex due to the body rotation. It is made even more difficult by noise induced in the geomagnetic signal by fluctuating magnetic field of the closely positioned motors. Filtering that noise is challenging since the rotation speed of motors and the vehicle can be very close. This paper presents analysis of motor induced noise, based on experimental data of brushless micro motors. A novel time domain filter is proposed, designed, implemented in FPGA hardware, tested and compared to other filters. This filter provides good performance even when the rotational rate of the motor and vehicle are close and traditional frequency domain filters would perform poorly.

  5. Aeromagnetic Survey by Small Unmanned Aerial Vehicle with Magneto-Resistant Magnetometer at the northern Kalgoorlie area, Western Australia

    Science.gov (United States)

    Funaki, M.; Group, A.; Milligan, P.

    2006-12-01

    We have developed the technology of small drones (unmanned aerial vehicles (UAV)) and an onboard magnetometer focussed on the aeromagnetic surveys under the Ant-Plane project. We succeeded long distant flight to 500km with agnetometer by Ant-Plene4 drone collaborated with Geoscience, Australia, in March 2006. The survey was carried out in the area 10kmx10km around Mt. Vetters Station, Kalgoorlie, West Australian. The magnetic data are obtained from 41 courses (250m in interval) of EW dierction. The altitude of the flight was 900m from sea level and 500m from the runway. The Ant-Plane #4 consists of 2.6m span and 2.0m length with 2-cycles and 2-cylinder 85cc gasoline engine, GPS navigation system by microcomputer and radio telemeter system. The total weight is 25kg including 12.4 litter fuels and the coursing speed is 130. The magnetometer system consists of a 3-component magneto- resistant magnetometer (MR) sensor (Honeywell HMR2300), GPS and data logger. Three components of magnetic field, latitude, longitude, altitude, the number of satellite and time can be recorded in every second during 6 hours. The sensitivity of the magnetometer is 7 nT and we use a total magnetic field intensity for magnetic analysis due to unknown direction of heading of the plane. MR-magnetometer sensor was installed at the tip of a FRP pipe of 1m length, and the pipe was fixed to the head of the plane in order to reduce the plane magnetization. After 4 hours 14 minutes from the takeoff, the 500km flight was accomplished and the magnetic data were obtained from the data logger. The straight flight course was almost consistent with the way point course, but the course was drastically disturbed when the plane was turning. The magnetic noise level during the flight increased to 30nT, when the plane was flight in the tail wind. However, it is much higher when the plane flew in the head wind. The anomaly pattern obtained from Ant-Plane 4 was compared with the magnetic anomaly map published by

  6. Real-time Geomagnetic Data from a Raspberry Pi Magnetometer Network in the United Kingdom

    Science.gov (United States)

    Case, N.; Beggan, C.; Marple, S. R.

    2017-12-01

    In 2014, BGS and the University of Lancaster won an STFC Public Engagement grant to build and deploy 10 Raspberry Pi magnetometers to secondary schools across the UK to enable citizen science. The system uses a Raspberry Pi computer as a logging and data transfer device, connected to a set of three orthogonal miniature fluxgate magnetometers. The system has a nominal sensitivity of around 1 nanoTesla (nT), in each component direction (North, East and Down). This is around twenty times less sensitive than a current scientific-level instrument, but given its relatively low-cost, at about £250 ($325) per unit, this is an excellent price-to-performance ratio given we could not improve the sensitivity unless we spent a lot more money. The magnetic data are sampled at a 5 second cadence and sent to the AuroraWatch website at Lancaster University every 2 minutes. The data are freely available to view and download. The primary aim of the project is to encourage students from 14-18 years old to look at how sensors can be used to collect geophysical data and integrate it together to give a wider understanding of physical phenomena. A second aim is to provide useful data on the spatial variation of the magnetic field for analysis of geomagnetic storms, alongside data from the BGS observatory and University of Lancaster's SAMNET variometer network. We show results from the build, testing and running of the sensors including some recent storms and we reflect on our experiences in engaging schools and the general public with information about the magnetic field. The information to build the system and logging and analysis software for the Raspberry Pi is all freely available, allowing those interested to participate in the project as citizen scientists.

  7. Geophysical Surveying of Shallow Magnetic Anomalies Using the iPhone Magnetometer

    Science.gov (United States)

    Opdyke, P.; Dudley, C.; Louie, J. N.

    2012-12-01

    This investigation examined whether the 3-axis Hall-effect magnetometer in the Apple iPhone 3GS can function as an effective shallow magnetic survey instrument. The xSensor Pro app from Crossbow Systems allows recoding of all three sensor components along with the GPS location, at a frequency of 1.0, 4.0, 16.0, and 32.0 Hz. If the iPhone proves successful in collecting useful magnetic data, then geophysicists and especially educators would have a new tool for high-density geophysical mapping. No-contract iPhones that can connect with WiFi can be obtained for about $400, allowing deployment of large numbers of instruments. iPhones with the xSensor Pro app surveyed in parallel with an Overhauser GEM system magnetometer (1 nT sensitivity) to test this idea. Anderson Bay, located on the Pyramid Lake Paiute Reservation, provided a rural survey location free from cultural interference. xSensor Pro, logged each component's intensity and the GPS location at a frequency of four measurements per second. Two Overhauser units functioned as a base unit and a roving unit. The roving unit collected total field at set points located with a handheld GPS. Comparing the total field computed from the iPhone components against that collected by the Overhauser establishes the level of anomalies that the iPhone can detect. iPhone total-field measurements commonly vary by 200 nT from point to point, so a spatial-temporal average over 25 seconds produces a smoothed signal for comparison. Preliminary analysis of the iPhone results show that the data do not accurately correlate to the total field collected by the Overhauser for any anomaly of less than 200 nT.

  8. Quantum-limited biochemical magnetometers designed using the Fisher information and quantum reaction control

    Science.gov (United States)

    Vitalis, K. M.; Kominis, I. K.

    2017-03-01

    Radical-ion pairs and their reactions have triggered the study of quantum effects in biological systems. This is because they exhibit a number of effects best understood within quantum information science, and at the same time are central in understanding the avian magnetic compass and the spin transport dynamics in photosynthetic reaction centers. Here we address radical-pair reactions from the perspective of quantum metrology. Since the coherent spin motion of radical pairs is effected by an external magnetic field, these spin-dependent reactions essentially realize a biochemical magnetometer. Using the quantum Fisher information, we find the fundamental quantum limits to the magnetic sensitivity of radical-pair magnetometers, arriving at a sensitivity δ B =2 pT /τ [1 μ s] √{ν0[1012] } , given in terms of radical-pair lifetime τ and number of radical pairs ν0. We then explore how well the usual measurement scheme considered in radical-pair reactions, the measurement of reaction yields, approaches the fundamental limits. In doing so, we find the optimal hyperfine interaction Hamiltonian that leads to the best magnetic sensitivity as obtained from reaction yields. This is still an order of magnitude smaller than the absolute quantum limit. Finally, we demonstrate that with a realistic quantum reaction control reminding one of Ramsey interferometry, here presented as a quantum circuit involving the spin-exchange interaction and a recently proposed molecular switch, we can approach the fundamental quantum limit within a factor of 2. This work opens the application of well-advanced quantum metrology methods to biological systems.

  9. A 3-Axis Miniature Magnetic Sensor Based on a Planar Fluxgate Magnetometer with an Orthogonal Fluxguide

    Directory of Open Access Journals (Sweden)

    Chih-Cheng Lu

    2015-06-01

    Full Text Available A new class of tri-axial miniature magnetometer consisting of a planar fluxgate structure with an orthogonal ferromagnetic fluxguide centrally situated over the magnetic cores is presented. The magnetic sensor possesses a cruciform ferromagnetic core placed diagonally upon the square excitation coil under which two pairs of pick-up coils for in-plane field detection are allocated. Effective principles and analysis of the magnetometer for 3-D field vectors are described and verified by numerically electromagnetic simulation for the excitation and magnetization of the ferromagnetic cores. The sensor is operated by applying the second-harmonic detection technique that can verify V-B relationship and device responsivity. Experimental characterization of the miniature fluxgate device demonstrates satisfactory spatial magnetic field detection results in terms of responsivity and noise spectrum. As a result, at an excitation frequency of 50 kHz, a maximum in-plane responsivity of 122.4 V/T appears and a maximum out-of-plane responsivity of 11.6 V/T is obtained as well. The minimum field noise spectra are found to be 0.11 nT/√Hz and 6.29 nT/√Hz, respectively, in X- and Z-axis at 1 Hz under the same excitation frequency. Compared with the previous tri-axis fluxgate devices, this planar magnetic sensor with an orthogonal fluxguide provides beneficial enhancement in both sensory functionality and manufacturing simplicity. More importantly, this novel device concept is considered highly suitable for the extension to a silicon sensor made by the current CMOS-MEMS technologies, thus emphasizing its emerging applications of field detection in portable industrial electronics.

  10. High-sensitivity multifunctional spinner magnetometer using a magneto-impedance sensor

    Science.gov (United States)

    Kodama, Kazuto

    2017-01-01

    A novel spinner magnetometer was developed with a wide dynamic range from 10-10 to 10-4 Am2 and a resolution of 10-11 Am2. High sensitivity was achieved with the use of a magneto-impedance (MI) sensor, which is a compact, sensitive magnetic sensor used industrially. Its slow-spinning rate (5 Hz) and the incorporation of a unique mechanism for adjusting the spacing between the sensing unit and the spinning axis allows the measurement of fragile samples sized 10-50 mm. The sensor configuration, in which a pair of MI sensors is connected in opposite serial, along with an amplification circuit with a programmable low-pass filter, reduces the problems of external noise and sensor drift. The signal, with reference to the spinning frequency, is detected with a lock-in amplifier. The MI spinner has two selectable measurement modes: the fundamental mode (F mode) and the harmonic mode (H mode). Measurements in the F mode detect signals of the fundamental frequency (5 Hz), in the same way as conventional spinner magnetometers. In the H mode, the second (10 Hz) and the third (15 Hz) harmonic components are measured, in addition to the fundamental component. Tests in the H mode were performed using a small coil and a natural sample to simulate dipoles with various degrees of offset. The results revealed that the magnitude of the fundamental component of the offset dipole was systematically larger (by several percent) than that of the nonoffset dipole. These findings suggest that this novel MI spinner will be useful in estimating the inhomogeneity of the magnetization of a sample that can equivalently be described by an offset dipole.

  11. Magnetometer-inferred, Equatorial, Daytime Vertical ExB Drift Velocities Observed in the African Longitude Sector

    Science.gov (United States)

    Anderson, D. N.; Yizengaw, E.

    2011-12-01

    A recent paper has investigated the sharp longitude gradients in the dayside ExB drift velocities associated with the 4-cell, non-migrating structures thought to be connected with the eastward propagating, diurnal, non-migrating (DE3) tides. Observations of vertical ExB drift velocities obtained from the Ion Velocity Meter (IVM) on the Communication/Navigation Outage Forecast System (C/NOFS) satellite were obtained in the Western Pacific, Eastern Pacific, Peruvian and Atlantic sectors for a few days during the months of October, March and December, 2009. Respective ExB drift velocity gradients at the cell boundaries for these 4 longitude sectors were a.) -1.3m/sec/degree, b.) 3m/sec/degree, c.) -4m/sec/degree and d.) 1m/sec/degree and were observed on a day-to-day basis. In this talk, we estimate the longitude gradients in the dayside, vertical ExB drift velocities from magnetometer H-component observations in the African sector. We briefly describe the technique for obtaining realistic ExB drift velocities associated with the difference in the H-component values between a magnetometer on the magnetic equator and one off the magnetic equator at 6 to 9 degrees dip latitude (delta H). We present magnetometer-inferred, dayside ExB drift velocities obtained from the AMBER (African Meridian B-field Education and Research) magnetometer chain in the East Africa (Ethiopian) longitude sector and the West African (Nigerian) longitude sector. We compare the longitude gradients in ExB drift velocities in the African sector with the C/NOFS- observed longitude gradients mentioned above. We also discuss the advantages of using ground-based magnetometer observations to infer ExB drift velocities compared with the C/NOFS satellite observations.

  12. The construction of prototype of vibrating sample magnetometer for analyzing the magnetic behaviours of TM/RE thin film

    International Nuclear Information System (INIS)

    Tri Mardji Atmono; Rita Prasetyowati; Angie Mega Rahayu Kartika

    2015-01-01

    This research is aimed to analyze the principles in the making of vibrating sample magnetometer (VSM), the influence of loudspeaker vibration frequency on the output voltage to get optimal result, the influence of the pick-up coil amplitude on voltage of induction signal of VSM prototype, and the magnetic characteristics of Ni bulk; the thin film of Co; as well as the thin film of RE/TM. The method of the sample preparation that will be tested, was done by using RF Sputtering to produce a thin film onto glass substrate. The VSM prototype was tested by optimizing the frequency, measuring the magnetization to the number of pick-up coil, and measuring the magnetization of the samples, which are Ni bulk, the thin film of Co, and the thin film of FeTb. The data analysis, in order to get the hysteresis curve which is the relation of M as function of B, used Microcal Origin 6.1 software. The calibration of voltage – magnetization was done by comparing the hysteresis curve of the Co-thin film, to the hysteresis curve measured by the commercial VSM made by Oxford. Based on the research outcome, a VSM prototype has been successful designed based on mechanical construction as its vibrator, which is composed of loudspeaker, rod holder, sample holder, and 2 parts of pick-up coil; also based on electronic construction having electromagnet, power supply, power amplifier, function generator, and lock-in amplifier. Then to obtain an optimal results, VSM prototype used loudspeaker with vibration frequency of 27 Hz and 2 pick-up coil for maximal induced voltage. After analyzing the magnetic characteristics of the sample, it is found that 3 × 10 -2 gram of Ni bulk has Ms = 6 × 10 -2 emu, Mr = 33 × 10 -3 emu, and Hc = 5 × 10 -3 T. The thin film of Co with surface area 4 mm × 4mm × 1,173 μm has Ms = 286 × 10 -4 emu, Mr = 25 × 10 -5 emu, and Hc = 5 × 10 -3 T. On the other hand, the thin film TbFe with surface area 7 mm × 18 mm has the characteristics of Ms =14 × 10 -4 emu

  13. Becoming Self-Employed.

    Science.gov (United States)

    Lee, Grant; Cochran, Larry

    1997-01-01

    Explored how persons become self-employed. In critical incident interviews with five self-employed persons the critical events that assisted or hindered progress toward self-employment were listed in chronological order. In general, becoming self-employed involved establishing conditions of action that enhanced a sense of agency, thus enabling…

  14. Electrodynamics of an omega-band as deduced from optical and magnetometer data

    Directory of Open Access Journals (Sweden)

    H. Vanhamäki

    2009-09-01

    Full Text Available We investigate an omega-band event that took place above northern Scandinavia around 02:00–02:30 UT on 9 March 1999. In our analysis we use ground based magnetometer, optical and riometer measurements together with satellite based optical images. The optical and riometer data are used to estimate the ionospheric Hall and Pedersen conductances, while ionospheric equivalent currents are obtained from the magnetometer measurements. These data sets are used as input in a local KRM calculation, which gives the ionospheric potential electric field as output, thus giving us a complete picture of the ionospheric electrodynamic state during the omega-band event. The overall structure of the electric field and field-aligned current (FAC provided by the local KRM method are in good agreement with previous studies. Also the E×B drift velocity calculated from the local KRM solution is in good qualitative agreement with the plasma velocity measured by the Finnish CUTLASS radar, giving further support for the new local KRM method. The high-resolution conductance estimates allow us to discern the detailed structure of the omega-band current system. The highest Hall and Pedersen conductances, ~50 and ~25 S, respectively, are found at the edges of the bright auroral tongue. Inside the tongue, conductances are somewhat smaller, but still significantly higher than typical background values. The electric field shows a converging pattern around the tongues, and the field strength drops from ~40 mV/m found at optically dark regions to ~10 mV/m inside the areas of enhanced conductivity. Downward FAC flow in the dark regions, while upward currents flow inside the auroral tongue. Additionally, sharp conductance gradients at the edge of an auroral tongue are associated with narrow strips of intense FACs, so that a strip of downward current flows at the eastern (leading edge and a similar strip of upward current is present at the western (trailing edge. The Joule

  15. Perspectives of employability skills

    OpenAIRE

    ANNE LOUISE NEWTON

    2017-01-01

    The study investigated the different perspectives held by young people, employers and policy makers around Employability Skills and it examined how young people learnt these skills. This study draws young peoples’ perspectives into the research around Employability Skills and highlights the way in which social and cultural capital mediate their development. The research points to a model to re-vision employability skills which recognises the many ways in which they are learnt, over time a...

  16. Study of turbulent spectra of the geomagnetic field using the data of the THEMIS satellite mission and ground magnetometers

    Science.gov (United States)

    Pinto, V. A.; Stepanova, M. V.; Valdivia, J. A.; Antonova, E. E.

    2010-12-01

    Turbulent fluctuations of the geomagnetic field have been studied using the data of the THEMIS satellite mission and and ground magnetometer data from auroral and sub-auroral station including of the SAMBA magnetometer chain, located in Chile and in the Antarctic peninsula. It was found that turbulent spectra obtained at the same geomagnetic field line on the ground level in both hemispheres and near the equatorial plane are generally similar. Using the Local Intermittency Measure technique it was also established that the observed turbulence has an intermittent behavior. The MLT and longitudinal dependence were found to be stronger near midnight inside the auroral zone, which corresponds to the satellite location at 12-18 Earth radii to the tail.

  17. Social innovation in employment

    NARCIS (Netherlands)

    Oeij, P.R.A.; Torre, W. van der; Santoclides, M.E

    2017-01-01

    This policy brief on Social Innovation of Employment informs on an inventory of challenges and policy recommendations based on the Case Study Report of Employment and on the Second Policy Foresight Workshop of Employment. A ‘paradigm shift’ is needed in the mind-set of policymakers. ‘Traditional’

  18. Youth employment in Egypt

    OpenAIRE

    Eekelen, Willem van; De Luca, Loretta; Ismail, Magwa

    2001-01-01

    Examines economic and social factors affecting youth employment in Egypt and describes three national programmes for the promotion of youth employment based on human resources development, direct job creation and support in self-employment and enterprise creation. Describes one public-private project in each case.

  19. Determining the direction of a geometrical/optical reference axis in the coordinate system of a triaxial magnetometer sensor

    DEFF Research Database (Denmark)

    Primdahl, Fritz; Brauer, Peter; Merayo, José M.G.

    2002-01-01

    The reference coordinate axes of a magnetic vector field sensor are related to the instrument digital output vector (U) over bar by the calibration matrix C and the offset vector (O) over bar. In addition, this reference coordinate system must be related to (at least) two externally accessible op...... for two different positions, rotated about a fixed reference axis; (2) in the Earth's field the magnetometer sensor is rotated about a fixed axis into a number of (at least three) positions....

  20. Airborne gamma-ray spectrometer and magnetometer survey: Huron quadrangle, South Dakota. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1981-04-01

    An airborne high sensitivity gamma-ray spectrometer and magnetometer survey was conducted over eleven (11) 2/sup 0/ x 1/sup 0/ NTMS quadrangles located in the states of Minnesota and Wisconsin and seven (7) 2/sup 0/ x 1/sup 0/ NTMS quadrangles in North and South Dakota. The quadrangles located within the North and South Dakota survey area include Devil's Lake, New Rockford, Jamestown, Aberdeen, Huron, Mitchell, and Sioux Falls. This report discusses the results obtained over the Huron map area. Traverse lines were flown in an east-west direction at a line spacing of six (6) miles. Tie lines were flown north-south approximately twenty-four (24) miles apart. A total of 21,481 line miles of geophysical data were acquired, compiled, and interpreted during the survey, of which 1459 line miles are in this quadrangle. The purpose of this study is to acquire and compile geologic and other information with which to assess the magnitude and distribution of uranium resources and to determine areas favorable for the occurrence of uranium in the United States.

  1. Airborne gamma-ray spectrometer and magnetometer survey: Chico quadrangle, California. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1981-05-01

    An airborne high sensitivity gamma-ray spectrometer and magnetometer survey was conducted over ten (10) areas over northern California and southwestern Oregon. These include the 2/sup 0/ x 1/sup 0/ NTMS quadrangles of Roseburg, Medford, Weed, Alturas, Redding, Susanville, Ukiah, and Chico along with the 1/sup 0/ x 2/sup 0/ areas of the Coos Bay quadrangle and the Crescent City/Eureka areas combined. This report discusses the results obtained over the Chico, California, map area. Traverse lines were flown in an east-west direction at a line spacing of three. Tie lines were flown north-south approximately twelve miles apart. A total of 16,880.5 line miles of geophysical data were acquired, compiled, and interpreted during the survey, of which 3026.4 line miles are in the quadrangle. The purpose of this study is to acquire and compile geologic and other information with which to assess the magnitude and distribution of uranium resources with which to assess the magnitude and distribution of uranium resources and to determine areas favorable for the occurrence of uranium in the United States.

  2. Airborne gamma-ray spectrometer and magnetometer survey: Chico quadrangle, California. Final report

    International Nuclear Information System (INIS)

    1981-05-01

    An airborne high sensitivity gamma-ray spectrometer and magnetometer survey was conducted over ten (10) areas over northern California and southwestern Oregon. These include the 2 0 x 1 0 NTMS quadrangles of Roseburg, Medford, Weed, Alturas, Redding, Susanville, Ukiah, and Chico along with the 1 0 x 2 0 areas of the Coos Bay quadrangle and the Crescent City/Eureka areas combined. This report discusses the results obtained over the Chico, California, map area. Traverse lines were flown in an east-west direction at a line spacing of three. Tie lines were flown north-south approximately twelve miles apart. A total of 16,880.5 line miles of geophysical data were acquired, compiled, and interpreted during the survey, of which 3026.4 line miles are in the quadrangle. The purpose of this study is to acquire and compile geologic and other information with which to assess the magnitude and distribution of uranium resources with which to assess the magnitude and distribution of uranium resources and to determine areas favorable for the occurrence of uranium in the United States

  3. Vector magnetometer based on synchronous manipulation of nitrogen-vacancy centers in all crystal directions

    Science.gov (United States)

    Zhang, Chen; Yuan, Heng; Zhang, Ning; Xu, Lixia; Zhang, Jixing; Li, Bo; Fang, Jiancheng

    2018-04-01

    Negatively charged nitrogen vacancy (NV‑) centers in diamond have been extensively studied as high-sensitivity magnetometers, showcasing a wide range of applications. This study experimentally demonstrates a vector magnetometry scheme based on synchronous manipulation of NV‑ center ensembles in all crystal directions using double frequency microwaves (MWs) and multi-coupled-strip-lines (mCSL) waveguide. The application of the mCSL waveguide ensures a high degree of synchrony (99%) for manipulating NV‑ centers in multiple orientations in a large volume. Manipulation with double frequency MWs makes NV‑ centers of all four crystal directions involved, and additionally leads to an enhancement of the manipulation field. In this work, by monitoring the changes in the slope of the resonance line consisting of multi-axes NV‑ centers, measurement of the direction of the external field vector was demonstrated with a sensitivity of {{10}\\prime}/\\sqrt{Hz} . Based on the scheme, the fluorescence signal contrast was improved by four times higher and the sensitivity to the magnetic field strength was improved by two times. The method provides a more practical way of achieving vector sensors based on NV‑ center ensembles in diamond.

  4. Airborne gamma-ray spectrometer and magnetometer survey Coos Bay, Oregon. Final report

    International Nuclear Information System (INIS)

    1981-05-01

    During the months of August, September, and October of 1980, Aero Service Division Western Geophysical Company of America conducted an airborne high sensitivity gamma-ray spectrometer and magnetometer survey over ten (10) areas over northern California and southwestern Oregon. These include the 2 0 x 1 0 NTMS quadrangles of Roseburg, Medford, Weed, Alturas, Redding, Susanville, Ukiah, and Chico along with the 1 0 x 2 0 areas of the Coos Bay quadrangle and the Crescent City/Eureka areas combined. This report discusses the results obtained over the Coos Bay, Oregon, map area. Line spacing was generally six miles for east/west traverses and eighteen miles for north/south tie lines over the northern one-half of the area. Traverses and tie lines were flown at three miles and twelve miles respectively over the southern one-half of the area. A total of 16,880.5 line miles of geophysical data were acquired, compiled, and interpreted during the survey, of which 863.8 line miles are in this quadrangle

  5. Signal Conditioning for the Kalman Filter: Application to Satellite Attitude Estimation with Magnetometer and Sun Sensors.

    Science.gov (United States)

    Esteban, Segundo; Girón-Sierra, Jose M; Polo, Óscar R; Angulo, Manuel

    2016-10-31

    Most satellites use an on-board attitude estimation system, based on available sensors. In the case of low-cost satellites, which are of increasing interest, it is usual to use magnetometers and Sun sensors. A Kalman filter is commonly recommended for the estimation, to simultaneously exploit the information from sensors and from a mathematical model of the satellite motion. It would be also convenient to adhere to a quaternion representation. This article focuses on some problems linked to this context. The state of the system should be represented in observable form. Singularities due to alignment of measured vectors cause estimation problems. Accommodation of the Kalman filter originates convergence difficulties. The article includes a new proposal that solves these problems, not needing changes in the Kalman filter algorithm. In addition, the article includes assessment of different errors, initialization values for the Kalman filter; and considers the influence of the magnetic dipole moment perturbation, showing how to handle it as part of the Kalman filter framework.

  6. Infrastructure-Less Indoor Localization Using the Microphone, Magnetometer and Light Sensor of a Smartphone

    Directory of Open Access Journals (Sweden)

    Carlos E. Galván-Tejada

    2015-08-01

    Full Text Available In this paper, we present the development of an infrastructure-less indoor location system (ILS, which relies on the use of a microphone, a magnetometer and a light sensor of a smartphone, all three of which are essentially passive sensors, relying on signals available practically in any building in the world, no matter how developed the region is. In our work, we merge the information from those sensors to estimate the user’s location in an indoor environment. A multivariate model is applied to find the user’s location, and we evaluate the quality of the resulting model in terms of sensitivity and specificity. Our experiments were carried out in an office environment during summer and winter, to take into account changes in light patterns, as well as changes in the Earth’s magnetic field irregularities. The experimental results clearly show the benefits of using the information fusion of multiple sensors when contrasted with the use of a single source of information.

  7. Investigation of a low-cost magneto-inductive magnetometer for space science applications

    Directory of Open Access Journals (Sweden)

    L. H. Regoli

    2018-03-01

    Full Text Available A new sensor for measuring low-amplitude magnetic fields that is ideal for small spacecraft is presented. The novel measurement principle enables the fabrication of a low-cost sensor with low power consumption and with measuring capabilities that are comparable to recent developments for CubeSat applications. The current magnetometer, a software-modified version of a commercial sensor, is capable of detecting fields with amplitudes as low as 8.7 nT at 40 Hz and 2.7 nT at 1 Hz, with a noise floor of 4 pT∕Hz at 1 Hz. The sensor has a linear response to less than 3 % over a range of ±100 000 nT. All of these features make the magneto-inductive principle a promising technology for the development of magnetic sensors for both space-borne and ground-based applications to study geomagnetic activity.

  8. Airborne gamma-ray spectrometer and magnetometer survey, New Rockford Quadrangle, North Dakota. Final report

    International Nuclear Information System (INIS)

    1981-04-01

    An airborne high sensitivity gamma-ray spectrometer and magnetometer survey was conducted over eleven (11) 2 0 x 1 0 NTMS quadrangles located in the states of Minnesota and Wisconsin and seven (7) 2 0 x 1 0 NTMS quadrangles in North and South Dakota. The quadrangles located within the North and South Dakota survey area include Devil's Lake, New Rockford, Jamestown, Aberdeen, Huron, Mitchell, and Sioux Falls. This report discusses the results obtained over the New Rockford map area. Traverse lines were flown in an east-west direction at a line spacing of six (6) miles. Tie lines were flown north-south approximately twenty-four (24) miles apart. A total of 21,481 line miles of geophysical data were acquired, compiled, and interpreted during the survey, of which 1397 line miles are in this quadrangle. The purpose of this study is to acquire and compile geologic and other information with which to assess the magnitude and distribution of uranium resources and to determine areas favorable for the occurrence of uranium in the United States

  9. In-Flight Calibration Methods for Temperature-Dependent Offsets in the MMS Fluxgate Magnetometers

    Science.gov (United States)

    Bromund, K. R.; Plaschke, F.; Strangeway, R. J.; Anderson, B. J.; Huang, B. G.; Magnes, W.; Fischer, D.; Nakamura, R.; Leinweber, H. K.; Russell, C. T.; hide

    2016-01-01

    During the first dayside season of the Magnetospheric Multiscale (MMS) mission, the in-flight calibration process for the Fluxgate magnetometers (FGM) implemented an algorithm that selected a constant offset (zero-level) for each sensor on each orbit. This method was generally able to reduce the amplitude of residual spin tone to less than 0.2 nT within the region of interest. However, there are times when the offsets do show significant short-term variations. These variations are most prominent in the nighttime season (phase 1X), when eclipses are accompanied by offset changes as large as 1 nT. Eclipses are followed by a recovery period as long as 12 hours where the offsets continue to change as temperatures stabilize. Understanding and compensating for these changes will become critical during Phase 2 of the mission in 2017, when the nightside will become the focus of MMS science. Although there is no direct correlation between offset and temperature, the offsets are seen for the period of any given week to be well-characterized as function of instrument temperature. Using this property, a new calibration method has been developed that has proven effective in compensating for temperature-dependent offsets during phase 1X of the MMS mission and also promises to further refine calibration quality during the dayside season.

  10. Airborne gamma-ray spectrometer and magnetometer survey: Huron quadrangle, South Dakota. Final report

    International Nuclear Information System (INIS)

    1981-04-01

    An airborne high sensitivity gamma-ray spectrometer and magnetometer survey was conducted over eleven (11) 2 0 x 1 0 NTMS quadrangles located in the states of Minnesota and Wisconsin and seven (7) 2 0 x 1 0 NTMS quadrangles in North and South Dakota. The quadrangles located within the North and South Dakota survey area include Devil's Lake, New Rockford, Jamestown, Aberdeen, Huron, Mitchell, and Sioux Falls. This report discusses the results obtained over the Huron map area. Traverse lines were flown in an east-west direction at a line spacing of six (6) miles. Tie lines were flown north-south approximately twenty-four (24) miles apart. A total of 21,481 line miles of geophysical data were acquired, compiled, and interpreted during the survey, of which 1459 line miles are in this quadrangle. The purpose of this study is to acquire and compile geologic and other information with which to assess the magnitude and distribution of uranium resources and to determine areas favorable for the occurrence of uranium in the United States

  11. Real-space imaging of non-collinear antiferromagnetic order with a single-spin magnetometer

    Science.gov (United States)

    Gross, I.; Akhtar, W.; Garcia, V.; Martínez, L. J.; Chouaieb, S.; Garcia, K.; Carrétéro, C.; Barthélémy, A.; Appel, P.; Maletinsky, P.; Kim, J.-V.; Chauleau, J. Y.; Jaouen, N.; Viret, M.; Bibes, M.; Fusil, S.; Jacques, V.

    2017-09-01

    Although ferromagnets have many applications, their large magnetization and the resulting energy cost for switching magnetic moments bring into question their suitability for reliable low-power spintronic devices. Non-collinear antiferromagnetic systems do not suffer from this problem, and often have extra functionalities: non-collinear spin order may break space-inversion symmetry and thus allow electric-field control of magnetism, or may produce emergent spin-orbit effects that enable efficient spin-charge interconversion. To harness these traits for next-generation spintronics, the nanoscale control and imaging capabilities that are now routine for ferromagnets must be developed for antiferromagnetic systems. Here, using a non-invasive, scanning single-spin magnetometer based on a nitrogen-vacancy defect in diamond, we demonstrate real-space visualization of non-collinear antiferromagnetic order in a magnetic thin film at room temperature. We image the spin cycloid of a multiferroic bismuth ferrite (BiFeO3) thin film and extract a period of about 70 nanometres, consistent with values determined by macroscopic diffraction. In addition, we take advantage of the magnetoelectric coupling present in BiFeO3 to manipulate the cycloid propagation direction by an electric field. Besides highlighting the potential of nitrogen-vacancy magnetometry for imaging complex antiferromagnetic orders at the nanoscale, these results demonstrate how BiFeO3 can be used in the design of reconfigurable nanoscale spin textures.

  12. Optimization of a digital SQUID magnetometer in terms of noise and distortion

    International Nuclear Information System (INIS)

    Haverkamp, I; Toepfer, H; Wetzstein, O; Kunert, J; Stolz, R; Meyer, H-G; Ortlepp, T

    2012-01-01

    The digital SQUID magnetometer takes advantage of flux quantization in a superconducting loop in order to measure magnetic fields. The core element of the digital SQUID is a Josephson comparator with a superconducting antenna loop attached to one of its junctions. Evaluation of the circuit from the system’s point of view requires an analysis in the frequency domain. In order to obtain a high-resolution fast Fourier transform, large datasets are necessary which are difficult to generate with transient simulation tools. In this work we derive a behavioural model for the digital SQUID in order to overcome restrictions imposed by transient simulation. By means of this model the influence of the comparator grey zone and the input loop inductance on the system performance was analysed. In order to assess the system, evaluation criteria based on the power spectral density were applied, which are commonly used for characterization of semiconductor analogue to digital converters. As a result of this study, design guidelines for an optimum antenna inductance depending on the comparator grey zone are derived, allowing us to achieve an optimum system performance in terms of noise and distortion. (paper)

  13. Swarm Deployable Boom Assembly (DBA) Development of a Deployable Magnetometer Boom for the Swarm Spacecraft

    Science.gov (United States)

    McMahon, Paul; Jung, Hans-Juergen; Edwards, Jeff

    2013-09-01

    The Swarm programme consists of 3 magnetically clean satellites flying in close formation designed to measure the Earth's magnetic field using 2 Magnetometers mounted on a 4.3m long deployable boom.Deployment is initiated by releasing 3 HDRMs, once released the boom oscillates back and forth on a pair of pivots, similar to a restaurant kitchen door hinge, for around 120 seconds before coming to rest on 3 kinematic mounts which are used to provide an accurate reference location in the deployed position. Motion of the boom is damped through a combination of friction, spring hysteresis and flexing of the 120+ cables crossing the hinge. Considerable development work and accurate numerical modelling of the hinge motion was required to predict performance across a wide temperature range and ensure that during the 1st overshoot the boom did not damage itself, the harness or the spacecraft.Due to the magnetic cleanliness requirements of the spacecraft no magnetic materials could be used in the design of the hardware.

  14. Airborne gamma-ray spectrometer and magnetometer survey, Mitchell Quadrangle, South Dakota. Final report

    International Nuclear Information System (INIS)

    1981-04-01

    An airborne high sensitivity gamma-ray spectrometer and magnetometer survey was conducted over eleven (11) 2 0 x 1 0 NTMS quadrangles located in the states of Minnesota and Wisconsin and seven (7) 2 0 x 1 0 NTMS quadrangles in North and South Dakota. The quadrangles located within the North and South Dakota survey area include Devil's Lake, New Rockford, Jamestown, Aberdeen, Huron, Mitchell, and Sioux Falls. This report discusses the results obtained over the Mitchell map area. The purpose of this program is to acquire and compile geologic and other information with which to assess the magnitude and distribution of uranium resources and to determine areas favorable for the occurrence of uranium in the United States. Traverse lines were flown in an east-west direction at a line spacing of six (6) miles. Tie lines were flown north-south approximately twenty-four (24) miles apart. A total of 21,481 line miles of geophysical data were acquired, compiled, and interpreted during the survey, of which 1479 line miles are in this quadrangle

  15. A LabVIEW software for Thellier paleointensity measurements with an automated three-component spinner magnetometer TSpin

    Science.gov (United States)

    Fukuma, Koji; Kono, Masaru

    2016-03-01

    The Thellier method is classical but is still regarded as the most reliable method for paleointensity determination. Recently, many types of additional protocols have been advocated to ensure reliability and make laboratory work more laborious and time-consuming. An automated system coupling a magnetometer and an electric furnace is now of prime importance to cope with the increasing demand. Here, we describe a graphics-based program for controlling a fully automatic system combining a spinner magnetometer and a thermal demagnetizer, and for acquiring and processing the magnetization data. A single fluxgate sensor, which can measure the vector magnetization by spinning and translating a standard-sized 1-in. specimen, was calibrated with a rotatable reference specimen that can make the magnetization parallel or perpendicular to the spinning axis. By placing a cooling chamber between the furnace and the sensor for the updated system, the specimen can be heated up more efficiently to ensure an identical thermal history for the double heatings of the Thellier method. The direction of the vector magnetization was precisely obtained as well as the intensity, the results being comparable with those from an ordinary spinner magnetometer. We present an application of the fully automatic system for a Thellier measurement on a recent lava flow, which took about 24 h for approximately ten-step double heatings without manual operation.

  16. Suppression of the Nonlinear Zeeman Effect and Heading Error in Earth-Field-Range Alkali-Vapor Magnetometers

    Science.gov (United States)

    Bao, Guzhi; Wickenbrock, Arne; Rochester, Simon; Zhang, Weiping; Budker, Dmitry

    2018-01-01

    The nonlinear Zeeman effect can induce splitting and asymmetries of magnetic-resonance lines in the geophysical magnetic-field range. This is a major source of "heading error" for scalar atomic magnetometers. We demonstrate a method to suppress the nonlinear Zeeman effect and heading error based on spin locking. In an all-optical synchronously pumped magnetometer with separate pump and probe beams, we apply a radio-frequency field which is in phase with the precessing magnetization. This results in the collapse of the multicomponent asymmetric magnetic-resonance line with ˜100 Hz width in the Earth-field range into a single peak with a width of 22 Hz, whose position is largely independent of the orientation of the sensor within a range of orientation angles. The technique is expected to be broadly applicable in practical magnetometry, potentially boosting the sensitivity and accuracy of Earth-surveying magnetometers by increasing the magnetic-resonance amplitude, decreasing its width, and removing the important and limiting heading-error systematic.

  17. Diamond Synthesis Employing Nanoparticle Seeds

    Science.gov (United States)

    Uppireddi, Kishore (Inventor); Morell, Gerardo (Inventor); Weiner, Brad R. (Inventor)

    2014-01-01

    Iron nanoparticles were employed to induce the synthesis of diamond on molybdenum, silicon, and quartz substrates. Diamond films were grown using conventional conditions for diamond synthesis by hot filament chemical vapor deposition, except that dispersed iron oxide nanoparticles replaced the seeding. This approach to diamond induction can be combined with dip pen nanolithography for the selective deposition of diamond and diamond patterning while avoiding surface damage associated to diamond-seeding methods.

  18. The Pulse Azimuth effect as seen in induction coil magnetometers located in California and Peru 2007–2010, and its possible association with earthquakes

    Directory of Open Access Journals (Sweden)

    J. C. Dunson

    2011-07-01

    Full Text Available The QuakeFinder network of magnetometers has recorded geomagnetic field activity in California since 2000. Established as an effort to follow up observations of ULF activity reported from before and after the M = 7.1 Loma Prieta earthquake in 1989 by Stanford University, the QuakeFinder network has over 50 sites, fifteen of which are high-resolution QF1005 and QF1007 systems. Pairs of high-resolution sites have also been installed in Peru and Taiwan.

    Increases in pulse activity preceding nearby seismic events are followed by decreases in activity afterwards in the three cases that are discussed here. In addition, longer term data is shown, revealing a rich signal structure not previously known in QuakeFinder data, or by many other authors who have reported on pre-seismic ULF phenomena. These pulses occur as separate ensembles, with demonstrable repeatability and uniqueness across a number of properties such as waveform, angle of arrival, amplitude, and duration. Yet they appear to arrive with exponentially distributed inter-arrival times, which indicates a Poisson process rather than a periodic, i.e., stationary process.

    These pulses were observed using three-axis induction coil magnetometers that are buried 1–2 m under the surface of the Earth. Our sites use a Nyquist frequency of 16 Hertz (25 Hertz for the new QF1007 units, and they record these pulses at amplitudes from 0.1 to 20 nano-Tesla with durations of 0.1 to 12 s. They are predominantly unipolar pulses, which may imply charge migration, and they are stronger in the two horizontal (north-south and east-west channels than they are in the vertical channels. Pulses have been seen to occur in bursts lasting many hours. The pulses have large amplitudes and study of the three-axis data shows that the amplitude ratios of the pulses taken from pairs of orthogonal coils is stable across the bursts, suggesting a similar source.

    This paper presents three

  19. Conjugate Observations of Field-Line Resonances in the Inner Magnetosphere from the MEASURE and SAMBA Magnetometer Chains

    Science.gov (United States)

    Zesta, E.; Boudouridis, A.; Berube, D.; Moldwin, M.

    2004-12-01

    The newly installed SAMBA (South American Meridional B-field Array) chain is a low latitude meridional chain of 11 magnetometers at L=1.1 to L=2.5 along the coast of Chile and in the Antarctica peninsula. Five of the SAMBA magnetometers at L=1.7 to L=2.5 are directly conjugate to an equivalent number of northern hemisphere magnetometers of the MEASURE (Magnetometers Along the Eastern Atlantic Seaboard for Undergraduate Research and Education) chain. A unique characteristic is that both the SAMBA and the MEASURE magnetometers are set up as pairs of stations making it possible to determine the local Field-Line Resonance (FLR) from conjugate points and thus testing the accuracy of the technique and the models used. An initial study of the local FLR from conjugate pairs of stations at L=1.6 and L=1.7 was done during the moderate storm of July 11, 2003. The frequency of the local resonance can be used to determine the equatorial mass density of the resonating flux tube. From our two conjugate pairs we found, surprisingly, that the difference between the derived mass density between these two very close L values does not agree with densities predicted by any of the existing models or from past observations. If this result is general and not an isolated or rare occurrence it indicates that our understanding of the inversion of FLRs to determine the equatorial mass density is not complete and existing models could be constrained by our observations. We have now isolated a period of approximately 60 days during 2003 with complete coverage from conjugate pairs of stations and we are extending the study of conjugate FLRs to a large amount of days in order to determine the generality, or not, of the results from the July 11, 2003 storm. Initial analysis indicates quite a number of asymmetries in the ULF wave power between the two hemispheres, which might be a contributing factor to the difference in the mass density derived from the conjugate pairs. We plan to investigate

  20. General Outside Employment

    Data.gov (United States)

    Montgomery County of Maryland — This dataset contains all outside employment requests held by employees of Montgomery County (excluding uniformed police officer) approved by the Ethics Commission...

  1. Meridian-scanning photometer, coherent HF radar, and magnetometer observations of the cusp: a case study

    Directory of Open Access Journals (Sweden)

    S. E. Milan

    1999-02-01

    Full Text Available The dynamics of the cusp region and post-noon sector for an interval of predominantly IMF By, Bz < 0 nT are studied with the CUTLASS Finland coherent HF radar, a meridian-scanning photometer located at Ny Ålesund, Svalbard, and a meridional network of magnetometers. The scanning mode of the radar is such that one beam is sampled every 14 s, and a 30° azimuthal sweep is completed every 2 minutes, all at 15 km range resolution. Both the radar backscatter and red line (630 nm optical observations are closely co-located, especially at their equatorward boundary. The optical and radar aurora reveal three different behaviours which can interchange on the scale of minutes, and which are believed to be related to the dynamic nature of energy and momentum transfer from the solar wind to the magnetosphere through transient dayside reconnection. Two interpretations of the observations are presented, based upon the assumed location of the open/closed field line boundary (OCFLB. In the first, the OCFLB is co-located with equatorward boundary of the optical and radar aurora, placing most of the observations on open field lines. In the second, the observed aurora are interpreted as the ionospheric footprint of the region 1 current system, and the OCFLB is placed near the poleward edge of the radar backscatter and visible aurora; in this interpretation, most of the observations are placed on closed field lines, though transient brightenings of the optical aurora occur on open field lines. The observations reveal several transient features, including poleward and equatorward steps in the observed boundaries, "braiding" of the backscatter power, and 2 minute quasi-periodic enhancements of the plasma drift and optical intensity, predominantly on closed field lines.Key words. Ionosphere (auroral ionosphere; plasma convection · Magnetospheric physics (magnetopause · cusp · and boundary layers

  2. Ground-based magnetometer arrays and geomagnetically induced currents in power grids: science and operations

    Science.gov (United States)

    Thomson, A. W.; Beggan, C.; Kelly, G.

    2012-12-01

    Space weather impacts on worldwide technological infrastructures are likely to be at their greatest between 2012 and 2015, during the peak and early descending phase of the current solar cycle. Examples of infrastructures at risk include power grids, pipelines, railways, communications, satellite operations, high latitude air travel and global navigation satellite systems. For example, severe magnetic storms in March 1989 and October 2003, near the peaks of recent solar cycles, were particularly significant in causing problems for a wide variety of technologies. Further back in time, severe storms in September 1859 and May 1921 are known to have been a problem for the more rudimentary technologies of the time. In this talk we will review how magnetic observatory data can best contribute to ongoing efforts to develop new space weather data products, particularly in aiding the management of electrical power transmission networks. Examples of existing and perhaps some suggestions for new data products and services will be given. Throughout, the need for near to real time data will be emphasised. We will also emphasise the importance of developing regional magnetometer networks and promoting magnetic data sharing to help turn research into operations. Developing research consortia, for example as in the European EURISGIC GIC project (www.eurisgic.eu), where magnetic and other data, as well as expertise, is pooled and shared is also recommended and adds to our ability to monitor the dynamic state of magnetospheric and ionospheric currents. We will discuss how industry currently perceives the space weather hazard, using recent examples from the power industry, where the concerns are with the risk to high voltage transformers and the safe and uninterrupted distribution of electrical power. Industry measurements of geomagnetic induced currents (GIC) are also vital for the validation of scientific models of the flow of GIC in power systems. Examples of GIC data sources and

  3. Observations of the Earth's polar cleft at large radial distances with the Hawkeye 1 magnetometer

    International Nuclear Information System (INIS)

    Farrell, W.M.; Van Allen, J.A.

    1990-01-01

    Based on 364-spacecraft passes through the dayside region, the position of the polar cleft at large redial distances was determined with the magnetometer flown on Hawkeye 1. This data set represents one of the largest to investigate the high-latitude region at large radial distances, making it ideal for the study of the cusp and cleft region. Identification of the cleft depended on noting strong negative deviations of the magnetic field strength in the region from that of the dipole field. In solar magnetic coordinates, cleft observations were found between 40 degree and 70 degree latitude and ±75 degree longitude, while in geocentric magnetospheric coordinates, these observations were found between 20 degree and 75 degree latitude and ± 75 degree longitude. The extreme longitudinal extent of 150 degree is larger than those reported in some previous studies. Large magnetic depressions associated with the cleft extend out to 12 R E . Beyond this point, low model dipole field strengths make the determination of the cleft based on magnetic depressions unreliable. The cleft occurrences fall within an oval in magnetic latitude and longitude, but this oval is of a statistical nature and cannot be interpreted as the shape of the region at a given moment. As reported in other studies, the cleft was observed to shift to lower latitudes as compared to its quiet time geometry during periods when Kp was large and when the interplanetary magnetic field (IMF) pointed in a southerly direction. A southerly shift was also observed when th solar wind bulk flow speed, V sw , was large (>450 km/s), and the region might have enlarged when solar wind pressure, P sw , was large. The variation of the cleft latitude with V sw and P sw has not been thoroughly examined in previous studies

  4. Youth-Education-Employment.

    Science.gov (United States)

    Wirtz, Willard; And Others

    The document presents the proceedings of an international symposium analyzing the relationship among youth, education, and employment, with emphasis on youth employment trends and the need to find solutions for unemployment problems. The objectives are to evaluate the existing relationship in the light of changing values and expectations of young…

  5. Homosexual Discrimination in Employment

    Science.gov (United States)

    Siniscalco, Gary R.

    1976-01-01

    Recent developments in homosexual activism regarding employment problems in both the public and private sector are analyzed. Focus is on the law governing private employment, where homosexuals are afforded the least legal protection against discrimination. Available from: the University of Santa Clara, Santa Clara, California 95053. (LBH)

  6. Maine's Employability Skills Program

    Science.gov (United States)

    McMahon, John M.; Wolffe, Karen E.; Wolfe, Judy; Brooker, Carrie

    2013-01-01

    This Practice Report describes the development and implementation of the "Maine Employability Skills Program," a model employment program developed by the Maine Division for the Blind and Visually Impaired (DBVI). The program was designed to support the efforts of the chronically unemployed or underemployed. These consumers were either…

  7. Employment Challenges in Kenya

    African Journals Online (AJOL)

    Dr Kazungu

    Key Words: Employment Challenge, Employment Policy, Kenya. 1.0 Context ... Fiscal Measures. √. ×. √. Source: own elaboration based on government documents. Key: √- policy measure present; ×- policy measure not present ..... are Republic of Korea (1960–2001); Malaysia (1967–1997); Malta (1963–1994); Oman.

  8. Dimensions of Adolescent Employment.

    Science.gov (United States)

    Mael, Fred A.; Morath, Ray A.; McLellan, Jeffrey A.

    1997-01-01

    Examines positive and negative correlates of adolescent work as a function of work dimensions. Results indicate that concurrent costs and benefits of adolescent employment may depend on dimensions of work as well as adolescent characteristics. Adolescent employment was generally related to subsequent work motivation and nonacademic performance.…

  9. Coupled-core fluxgate magnetometer: Novel configuration scheme and the effects of a noise-contaminated external signal

    Energy Technology Data Exchange (ETDEWEB)

    Palacios, Antonio [San Diego State University, Nonlinear Dynamical Systems Group, Department of Mathematics and Statistics, San Diego, CA 92182-7720 (United States)]. E-mail: palacios@euler.sdsu.edu; Aven, John [San Diego State University, Nonlinear Dynamical Systems Group, Department of Mathematics and Statistics, San Diego, CA 92182-7720 (United States); In, Visarath [Space and Naval Warfare Systems Center San Diego, Code 2363, 53560 Hull St, San Diego, CA 92152-5001 (United States)]. E-mail: visarath@spawar.navy.mil; Longhini, Patrick [Space and Naval Warfare Systems Center San Diego, Code 2363, 53560 Hull St, San Diego, CA 92152-5001 (United States); Kho, Andy [Space and Naval Warfare Systems Center San Diego, Code 2363, 53560 Hull St, San Diego, CA 92152-5001 (United States); Neff, Joseph D. [Space and Naval Warfare Systems Center San Diego, Code 2363, 53560 Hull St, San Diego, CA 92152-5001 (United States); Bulsara, Adi [Space and Naval Warfare Systems Center San Diego, Code 2363, 53560 Hull St, San Diego, CA 92152-5001 (United States)]. E-mail: bulsara@spawar.navy.mil

    2007-07-16

    Recent theoretical and experimental work has shown that unidirectional coupling can induce oscillations in overdamped and undriven nonlinear dynamical systems that are non-oscillatory when uncoupled; in turn, this has been shown to lead to new mechanisms for weak (compared to the energy barrier height) signal detection and amplification. The potential applications include fluxgate magnetometers, electric field sensors, and arrays of Superconducting Quantum Interference Device (SQUID) rings. In the particular case of the fluxgate magnetometer, we have developed a ''coupled-core fluxgate magnetometer'' (CCFM); this device has been realized in the laboratory and its dynamics used to quantify many properties that are generic to this class of systems and coupling. The CCFM operation is underpinned by the emergent oscillatory behavior in a unidirectionally coupled ring of wound ferromagnetic cores, each of which can be treated as an overdamped bistable dynamic system when uncoupled. In particular, one can determine the regimes of existence and stability of the (coupling-induced) oscillations, and the scaling behavior of the oscillation frequency. More recently, we studied the effects of a (Gaussian) magnetic noise floor on a CCFM system realized with N=3 coupled ferromagnetic cores. In this Letter, we first introduce a variation on the basic CCFM configuration that affords a path to enhanced device sensitivity, particularly for N>=3 coupled elements. We then analyze the response of the basic CCFM configuration as well as the new setup to a dc target signal that has a small noisy component (or ''contamination'')

  10. Development of Meandering Winding Magnetometer (MWM (Register Trademark)) Eddy Current Sensors for the Health Monitoring, Modeling and Damage Detection of High Temperature Composite Materials

    Science.gov (United States)

    Russell, Richard; Washabaugh, Andy; Sheiretov, Yanko; Martin, Christopher; Goldfine, Neil

    2011-01-01

    The increased use of high-temperature composite materials in modern and next generation aircraft and spacecraft have led to the need for improved nondestructive evaluation and health monitoring techniques. Such technologies are desirable to improve quality control, damage detection, stress evaluation and temperature measurement capabilities. Novel eddy current sensors and sensor arrays, such as Meandering Winding Magnetometers (MWMs) have provided alternate or complimentary techniques to ultrasound and thermography for both nondestructive evaluation (NDE) and structural health monitoring (SHM). This includes imaging of composite material quality, damage detection and .the monitoring of fiber temperatures and multidirectional stresses. Historically, implementation of MWM technology for the inspection of the Space Shuttle Orbiter Reinforced Carbon-Carbon Composite (RCC) leading edge panels was developed by JENTEK Sensors and was subsequently transitioned by NASA as an operational pre and post flight in-situ inspection at the Kennedy Space Center. A manual scanner, which conformed'automatically to the curvature of the RCC panels was developed and used as a secondary technique if a defect was found during an infrared thermography screening, During a recent proof of concept study on composite overwrapped pressure vessels (COPV's), three different MWM sensors were tested at three orientations to demonstrate the ability of the technology to measure stresses at various fiber orientations and depths. These results showed excellent correlation with actual surface strain gage measurements. Recent advancements of this technology have been made applying MWM sensor technology for scanning COPVs for mechanical damage. This presentation will outline the recent advance in the MWM.technology and the development of MWM techniques for NDE and SHM of carbon wraped composite overwrapped pressure vessels (COPVs) including the measurement of internal stresses via a surface mounted sensor

  11. Magnetorelaxometry of few Fe{sub 3}O{sub 4} nanoparticles at 77 K employing a self-compensated SQUID magnetometer

    Energy Technology Data Exchange (ETDEWEB)

    Guillaume, Alexander; Scholtyssek, Jan M.; Lak, Aidin; Kassner, Alexander; Ludwig, Frank; Schilling, Meinhard

    2016-06-15

    Magnetic nanoparticles (MNPs) are of great interest for industrial and medical applications. Therefore, the properties of the particles have to be well controlled. Several magnetic measurement schemes have been developed in order to determine particle parameters such as size distribution and structural properties. In general, systems are designed either for the analysis of large amounts of MNP (≫1000) or for single particle investigation. Up to now, the region in between has been less studied. However, small and well defined amounts of MNPs are of high interest, e.g. for the systematic investigation of particle–particle interactions. In this paper, we present a method using electron beam lithographic preparation of small amounts of MNPs directly on a self-compensating high-temperature superconducting quantum interference device (SQUID) with micrometer dimensions which is insensitive to homogeneous fields and first order gradients but very sensitive to internal magnetic dipole fields. Magnetorelaxometry (MRX) measurements were carried out at 77 K sample temperature in a magnetically shielded room in order to analyze the dynamic behavior of MNP samples and to evaluate the detection limit of our SQUID sensors. Calculations based on the magnetic moment superposition model (MSM) and finite element simulations (FEM) indicate that the MNP samples can be fabricated in a well-defined way by the presented method. Based on MRX measurements of a sample with 200 single-core magnetite MNPs with core diameters of 12 nm, we estimate the detection limit of our SQUID MRX setup as 70 MNPs. - Highlights: • Novel self-compensated superconducting quantum interference device (SQUID). • Electron-beam lithographical patterning of magnetic nanoparticles directly on SQUID. • Magnetorelaxometric detection of 200 nanoparticles with diameter of 12 nm at 77 K. • FEM simulations provide detection limit of less than 100 nanoparticles.

  12. Institutionalized Employer Collective Action

    DEFF Research Database (Denmark)

    Ibsen, Christian Lyhne; Navrbjerg, Steen Erik

    2016-01-01

    Recent studies show that employer associations continue to exist in new ways despite internationalisation of the economy, liberalisation of markets and the decline of trade unions. This paradox raises two questions regarding EOs in today’s labour markets: Which employers join employer associations...... and what kind of services do EOs offer employers? This article explores these questions using two comprehensive surveys on EOs in Denmark – a prominent case of coordinated market economies. The main finding of the analyses is that collective activities vis-à-vis trade unions and government are still...... important but that individual and selective goods are just as important for recruitment and retention of members. The most important predictor of EO-membership is the existence of a collective agreement. Local union power and representation is not significant which supports the idea that EOs...

  13. Youth Employment and Unemployment

    Science.gov (United States)

    OECD Observer, 1977

    1977-01-01

    Discusses youth employment and unemployment in Canada, France, Germany, Italy, Japan, United Kingdom, and the United States; the trends, causes, consequences, policy goals, and specific measures needed to resolve problems. (SL)

  14. On the control of magnetic perturbing field onboard landers: the Magnetometer Protection program for the ESA ExoMars/Humboldt MSMO magnetometer experiment

    DEFF Research Database (Denmark)

    Menvielle, M.; Primdahl, Fritz; Brauer, Peter

    as characterizing its sub-surface. Magnetic fields are generated by electric currents in the planetary space environment, induced currents in the planetary interior and possibly remanent magnetism. In consequence, hardly any other single physical quantity can be used in such a variety of studies related...

  15. Employers meet employees

    OpenAIRE

    Scheuer, Christian

    2009-01-01

    "Leaping into the future of labor economics: the research potential of linking employer and employee data" is the title of a paper by Daniel S Hammermesh published in Labour Economics in 1999. I quote it here, since it captures much of my motivation for the work included in this thesis. Considering applied micro econometrics and labor economics my main elds of interest, the development of linked employer-employee data that took place in Denmark around the time of the new mille...

  16. Deficiency of employability capacity

    Directory of Open Access Journals (Sweden)

    Pelse I.

    2012-10-01

    Full Text Available Young unemployed people have comprised one of the significantly largest groups of the unemployed people in Latvia in recent years. One of the reasons why young people have difficulty integrating into the labour market is the “expectation gap” that exists in the relations between employers and the new generation of workers. Employers focus on capacity-building for employability such individual factors as strength, patience, self-discipline, self-reliance, self-motivation, etc., which having a nature of habit and are developed in a long-term work socialization process, which begins even before the formal education and will continue throughout the life cycle. However, when the socialization is lost, these habits are depreciated faster than they can be restored. Currently a new generation is entering the labour market, which is missing the succession of work socialization. Factors, such as rising unemployment and poverty in the background over the past twenty years in Latvia have created a very unfavourable employability background of “personal circumstances” and “external factors”, which seriously have impaired formation of the skills and attitudes in a real work environment. The study reveals another paradox – the paradox of poverty. Common sense would want to argue that poverty can be overcome by the job. However, the real state of affairs shows that unfavourable coincidence of the individual, personal circumstances and external factors leads to deficit of employability capacity and possibility of marked social and employment deprivation.

  17. Reducing Employment Insecurity

    Directory of Open Access Journals (Sweden)

    Florence Lebert

    2016-10-01

    Full Text Available The perception of job insecurity is known to be a stressful condition for employees. Less is known about employment insecurity and the ways employees and their families deal with it. This study investigates whether participation in further training is a strategy that employees adopt to reduce perceived employment insecurity. As participation in further training is often costly and time-consuming, we assume that the family context is of importance for the decision to take part in further training. To take account of possible self-selection, we apply a propensity score matching procedure on longitudinal data from the Swiss Household Panel (2004-2013. Three main findings can be emphasized: first, participation in further training is not a strategy adopted particularly by employees who perceive high employment insecurity as they are less likely to train than their secure counterparts. Second, even though further training is not a strategy that is actively adopted, employees who train subsequently report lower levels of perceived employment insecurity. Third, the family context indeed influences the likelihood to train: partnered employees are more likely to train and preschool-aged children act as a constraint on women’s but enhance men’s participation in further training. Yet, in the context of high perceived employment insecurity, children generally reduce their parents’ likelihood to train as the parents may turn to other strategies that reduce perceived employment insecurity.

  18. Field Line Resonance conjugate studies in the dayside inner magnetosphere using SAMBA antarctic magnetometers and THEMIS mission probes

    Science.gov (United States)

    Pinto, V. A.; Stepanova, M. V.; Zesta, E.; Boudouridis, A.; Valdivia, J. A.

    2011-12-01

    To test the robustness of the automated Field Line Resonance (FLR) technique described by [Boudouridis and Zesta 2007], and commonly used for the estimation of the plasma density in the inner magnetosphere, conjugate studies between the SAMBA magnetometer array and the THEMIS satellite were performed. An excellent conjunction, with a duration of nearly 40 minutes, between Escudero (ESC) and O'Higgins (OHI) antarctic fluxgate magnetometers from SAMBA and three probes from THEMIS was found on June 16, 2007. It is shown that the amplitude ratio method for the estimation of the frequency of resonance is more reliable than the phase difference method. For the amplitude ratio method we found time intervals in which we have the same resonance frequency in both ground and space measurements. We also compared this estimation with the in-situ ion number density measurements from the THEMIS satellites. It was found that the plasma density obtained from the FLR frequency is more fluctuating than the ion number density observed by THEMIS ESA and SST instruments. The time intervals for wich the plasma density and the number density are strongly correlated are much shorter than the intervals of high correlation between ground and space field line resonance frequencies. We investigate if the difference can be attributed to the orbital and/or ion composition effects.

  19. An Improved PDR/Magnetometer/Floor Map Integration Algorithm for Ubiquitous Positioning Using the Adaptive Unscented Kalman Filter

    Directory of Open Access Journals (Sweden)

    Jian Wang

    2015-11-01

    Full Text Available In this paper, a scheme is presented for fusing a foot-mounted Inertial Measurement Unit (IMU and a floor map to provide ubiquitous positioning in a number of settings, such as in a supermarket as a shopping guide, in a fire emergency service for navigation, or with a hospital patient to be tracked. First, several Zero-Velocity Detection (ZDET algorithms are compared and discussed when used in the static detection of a pedestrian. By introducing information on the Zero Velocity of the pedestrian, fused with a magnetometer measurement, an improved Pedestrian Dead Reckoning (PDR model is developed to constrain the accumulating errors associated with the PDR positioning. Second, a Correlation Matching Algorithm based on map projection (CMAP is presented, and a zone division of a floor map is demonstrated for fusion of the PDR algorithm. Finally, in order to use the dynamic characteristics of a pedestrian’s trajectory, the Adaptive Unscented Kalman Filter (A-UKF is applied to tightly integrate the IMU, magnetometers and floor map for ubiquitous positioning. The results of a field experiment performed on the fourth floor of the School of Environmental Science and Spatial Informatics (SESSI building on the China University of Mining and Technology (CUMT campus confirm that the proposed scheme can reliably achieve meter-level positioning.

  20. Highly sensitive YBa2Cu3O7 dc SQUID magnetometer with thin-film flux transformer

    Science.gov (United States)

    Grundler, D.; David, B.; Eckart, R.; Dössel, O.

    1993-11-01

    We have designed and fabricated a thin-film flux transformer by a YBa2Cu3O7/SrTiO3 (YBCO/STO) multilayer process. The flux transformer consists of a 20-turn input coil of 10 μm linewidth and a single-turn pickup loop surrounding an area of 7.5 by 7.5 mm2. All device levels are patterned by standard photolithography and Ar-ion-beam etching. The flux transformer has been combined in flip-chip configuration with the square washer of a low-noise YBCO dc SQUID. The dc SQUID magnetometer exhibits a magnetic field sensitivity of 1.4 nT/Φ0. The intrinsic white flux noise level of 70μΦ0/√Hz at 77 K is mainly dominated by the SQUID corresponding to a magnetic field resolution of the magnetometer of 100 fT/√Hz for frequencies above 40 Hz. At 1 Hz we measured 200 fT/√Hz. Biomagnetic measurements were performed in a magnetically shielded chamber.

  1. The effect of body mass and sex on the accuracy of respiratory magnetometers for measurement of end-expiratory lung volumes.

    Science.gov (United States)

    Avraam, Joanne; Bourke, Rosie; Trinder, John; Nicholas, Christian L; Brazzale, Danny; O'Donoghue, Fergal J; Rochford, Peter D; Jordan, Amy S

    2016-11-01

    Respiratory magnetometers are increasingly being used in sleep studies to measure changes in end-expiratory lung volume (EELV), including in obese obstructive sleep apnea patients. Despite this, the accuracy of magnetometers has not been confirmed in obese patients nor compared between sexes. Thus we compared spirometer-measured and magnetometer-estimated lung volume and tidal volume changes during voluntary end-expiratory lung volume changes of 1.5, 1, and 0.5 l above and 0.5 l below functional respiratory capacity in supine normal-weight [body mass index (BMI) 30 kg/m) men and women. Two different magnetometer calibration techniques proposed by Banzett et al. [Banzett RB, Mahan ST, Garner DM, Brughera A, Loring SH. J Appl Physiol (1985) 79: 2169-2176, 1995] and Sackner et al. [Sackner MA, Watson H, Belsito AS, Feinerman D, Suarez M, Gonzalez G, Bizousky F, Krieger B. J Appl Physiol (1985) 66: 410-420, 1989] were assessed. Across all groups and target volumes, magnetometers overestimated spirometer-measured EELV by ~65 ml (women for all target volumes except +0.5 l, whereas no differences between mass or sex groups were observed for the Sackner technique. The variability of breath-to-breath measures of EELV was significantly higher for obese compared with nonobese subjects and was higher for the Sackner than Banzett technique. On the other hand, for tidal volume, both calibration techniques underestimated spirometer measurements (men than in women (0.003). These results indicate that both body mass and sex affect the accuracy of respiratory magnetometers in measuring EELV and tidal volume. Copyright © 2016 the American Physiological Society.

  2. Implementing public employment policy

    DEFF Research Database (Denmark)

    Larsen, Flemming; Bredgaard, Thomas

    . But there is an interesting question to investigate here: whether and if so how, NPM-inspired reforms are related to changes in employment policy towards a work-first approach? Are changes in public management systems created as deliberate policy changes, or do they bring about more indirect and unintended policy changes......Like most other areas within welfare policy, the employment and social policy areas are undergoing far-reaching changes in many countries. Partly in the shape of new forms of governance inspired by New Public Management (NPM), partly through new policies oriented towards activation and stronger...... disciplining of the unemployed (work first) (cf.Bredgaard & Larsen, 2005; Sol & Westerweld, 2005). It is, however, remarkable that in the research field there seems to be a division of labour so that changes in public administration and changes in the substance of employment policies are dealt with separately...

  3. Employment certificates on HRT

    CERN Multimedia

    HR Department

    2008-01-01

    As part of the ongoing drive to simplify and streamline administrative procedures and processes, the IT and HR Departments have made employment certificates available on a self-service basis on the HRT application, in the main menu under "My self services". All members of the personnel can thus obtain a certificate of employment or association, in French or in English, for the present or past contractual period. The HR Department’s Records Office remains responsible for issuing any special certificates that might be required. IT-AIS (Administrative Information Services) HR-SPS (Services, Procedures & Social) Records Office – Tel. 73700

  4. Policies for full employment

    DEFF Research Database (Denmark)

    de Koning, Jaap; Layard, Richard; Nickel, Stephen

    European unemployment is too high, and employment is too low. Over 7½ per cent of Europe's workforce is unemployed, and only two thirds of people aged 15-64 are in work. At the Lisbon summit two years ago the heads of government set the target that by 2010 the employment rate should rise from 64 ......, the Netherlands and Sweden). And seven of the 15 countries in the E.U already have lower unemployment than the United States (the previous four plus Austria, Ireland and Luxembourg)....

  5. Youth, family and employment.

    Science.gov (United States)

    Peters, J F

    1987-01-01

    Some of the functions and dysfunctions of youth employment in contemporary society are discussed. The focus then shifts to a third variable: family dynamics. The research indicates that youth unemployment prolongs residence with parents. The younger the youth, the more tolerant are the parents of the unemployment. It was also found that a daughter's lack of employment in the summer months is more acceptable than a son's; that debts are part of the lifestyle of youth after age 18; that males incur more debts than do females; and that parents are the major source of financial loans.

  6. Implementing the employability agenda

    DEFF Research Database (Denmark)

    Lee, Donna; Snaith, Holly Grace; Foster, Emma

    2014-01-01

    This article draws on research commissioned by the Higher Education Academy (HEA) and conducted during 2013. It interrogates the ways in which the employability agenda has been fed through to the level of individual politics departments. The project was particularly concerned with establishing...... whether, and how, colleagues in politics and international relations (IR) had taken ownership of student employability at the level of the curriculum. In the article, the key findings of the research are summarised. There is also discussion of the (sometimes troubling) professional implications...... of infusing concern for graduate outcomes within a pedagogic framework that emphasises critical engagement with the underpinning political structures of the labour market....

  7. Governing EU employment policy

    DEFF Research Database (Denmark)

    Sørensen, Eva; Triantafillou, Peter; Damgaard, Bodil

    2015-01-01

    In the European Union (EU), employment policy is a prerogative of the member states. Therefore the EU's ability to govern in this area depends on its capability to involve national governments and relevant stakeholders in a collaborative effort to formulate and implement shared policy objectives....... Drawing an analytical distinction between cooperation, coordination and collaboration, the article analyses the formulation and implementation of EU employment policies. It concludes that while the formulation of policy objectives and the discussion of national policy approaches do involve elements...... of collaboration, the implementation phase mainly consists in the less demanding forms of cooperation and coordination....

  8. Radiation protection - the employer

    International Nuclear Information System (INIS)

    Goldfinch, E.

    1983-01-01

    A brief report is given of a paper presented at the symposium on 'Radiation and the Worker - where do we go from here' in London 1983. The paper concerned the employers' viewpoint on the draft of the proposed Ionising Radiations Regulations in the Health and Safety Commission Consultative Document. It was concluded that there was already a very good standard of radiological protection in the UK and that any improvements could therefore only be fringe improvements, although the cost to the employer of introducing and implementing the new proposed Regulations was bound to be high. (U.K.)

  9. Declining Black Employment.

    Science.gov (United States)

    Vedder, Richard; Gallaway, Lowell

    1993-01-01

    Explores income inequality during declining African-American employment, examines current welfare systems, and suggests ways to improve the economic disadvantages of minority groups. Letting markets work can improve the economic status of African Americans. The present dual African-American economy, a market economy and an entitlement economy, is…

  10. Views of the employers

    International Nuclear Information System (INIS)

    Ishida, J.

    2003-01-01

    The employer shall establish and maintain a safety management system, which is a part of the overall management system that facilitates the management of the occupational health and safety risks associated with the business of the organization. In addition to meeting its legal responsibilities, the employer should aim to improve its occupational health and safety performance, and its safety management system, effectively and efficiently, to meet changing business and regulatory needs. Occupational radiation protection is also a part of its activities. The concept of 'as low as reasonably achievable' (ALARA) presumes that any increment of radiation dose may produce a proportionate incremental risk, and that all radiation doses shall be kept ALARA, taking into account social and economic factors. Up to now, by implementing various activities in accordance with the principle of ALARA, employers have been minimizing the exposure dose of plant workers. Owing to improvements in hardware and administrative control, the exposure dose of workers has followed a remarkable downward trend, and now the number of workers exceeding 20 mSv/a is nearly zero. By implementing more thorough radiation protection and safety programmes, as well as by promoting safety consciousness among individual workers, the employers are continuing their efforts, respecting ALARA, to prevent workers from being exposed to radiation unnecessarily. As a consequence, the average individual dose of workers has dropped to 1 mSv/a or so. There may no longer be a discernible decrease in doses received at most of nuclear facilities

  11. Employment without Growth

    DEFF Research Database (Denmark)

    Nørgaard, Jørgen

    Employment is a central argument for economic growth in the Western world. But environmental problems like global warming points towards limits to growth. The presentation outlines the history of what has lead to this dilemma. Fortunately citizens attitudes now points towards a preference for less...

  12. Should Universities Promote Employability?

    Science.gov (United States)

    McCowan, Tristan

    2015-01-01

    Employability is becoming increasingly central to the mission and functioning of universities, spurred on by national and supranational agencies, and the demands of marketisation. This article provides a response to the normative dimensions of the question, progressing through four stages: first, there is a brief consideration of the meaning and…

  13. Employment Relations in Denmark

    DEFF Research Database (Denmark)

    Madsen, Jørgen Steen; Due, Jesper Jørgen; Andersen, Søren Kaj

    2011-01-01

    Jørgen Steen Madsen, Jesper Due og Søren Kaj Andersen har skrevet et kapitel om udviklingen i dansk arbejdsmarkedsregulering til bogen International and Comparative Employment Relations, redigeret af Greg Bamber, Russell Lansbury og Nick Wailes. Bogen indeholder bidrag, der præsenterer og...

  14. Shifting employment revisited

    NARCIS (Netherlands)

    Cremers, J.; Gramuglia, A.

    2014-01-01

    The CLR-network examined in 2006 the phenomenon of undeclared labour, with specific regard to the construction sector. The resulting study, Shifting Employment: undeclared labour in construction, gave evidence that this is an area particularly affected by undeclared activities with one of the

  15. Shifting employment revisited

    NARCIS (Netherlands)

    Cremers, Jan; Gramuglia, Alessia

    2014-01-01

    The CLR-network examined in 2006 the phenomenon of undeclared labour, with specific regard to the construction sector. The resulting study, Shifting Employment: undeclared labour in construction (Shifting-study hereafter), gave evidence that this is an area particularly affected by undeclared

  16. A Stochastic Employment Problem

    Science.gov (United States)

    Wu, Teng

    2013-01-01

    The Stochastic Employment Problem(SEP) is a variation of the Stochastic Assignment Problem which analyzes the scenario that one assigns balls into boxes. Balls arrive sequentially with each one having a binary vector X = (X[subscript 1], X[subscript 2],...,X[subscript n]) attached, with the interpretation being that if X[subscript i] = 1 the ball…

  17. The Employment Mismatch

    Science.gov (United States)

    Fischer, Karin

    2013-01-01

    Employers value a four-year college degree, many of them more than ever. Yet half of those surveyed recently by "The Chronicle" and American Public Media's "Marketplace" said they had trouble finding recent graduates qualified to fill positions at their company or organization. Nearly a third gave colleges just fair to poor marks for producing…

  18. An Exploration of Employer Perceptions of Graduate Student Employability

    Science.gov (United States)

    Chhinzer, Nita; Russo, Anna Maria

    2018-01-01

    Purpose: The purpose of this paper is to explore employer perceptions of graduate student employability. This study is novel since existing research focused on employability is largely theoretic, remains focused on defining employability of undergraduates and largely fails to determine employer perceptions of factors that increase or decrease…

  19. Energy levy and employment

    International Nuclear Information System (INIS)

    De Mooij, R.A.

    1993-01-01

    The employment in the Netherlands seems to be relatively vulnerable for an energy levy compared to other European countries. Therefore, implementation of an energy levy because of the environment demands a supporting policy for the employment. This can be realized by using the yield of the levy totally for the decrease of the tax burden on labour. An unbalanced distribution of incomes between the working population and the unemployed population must be taken for granted. Based on the general equilibrium model ENTAX (ENvironmental TAXation) for a small economy a number of factors, which can impact the cost effectiveness of a regulating energy levy, are discussed. Six countries (Netherlands, Belgium, Denmark, Germany, France and the United Kingdom) are compared regarding these factors. 4 tabs., 15 refs

  20. Employment and winter construction

    DEFF Research Database (Denmark)

    Hansen, Ernst Jan de Place; Larsen, Jacob Norvig

    2011-01-01

    Reduced seasonal building activity in the construction sector is often assumed to be related to hard winter conditions for building activities and poor working conditions for construction workers, resulting in higher costs and poor quality of building products, particularly in the northern...... hemisphere. Can climatic conditions alone explain the sizeable difference in reduction in building activity in the construction sector in European countries in the winter months, or are other factors such as technology, economic cycles and schemes for financial compensation influential as well? What...... possibilities exist for reducing seasonal variation in employment? In addition to a literature review related to winter construction, European and national employment and meteorological data were studied. Finally, ministerial acts, ministerial orders or other public policy documents related to winter...

  1. Entrepreneurship and Employment Stability

    DEFF Research Database (Denmark)

    Failla, Virgilio; Melillo, Francesca; Reichstein, Toke

    2017-01-01

    are identified and empirically explored: (i) job matching, (ii) labour market value, and (iii) personal commitment. Entrepreneurs appear to be more productive and thus better matched compared to wageworkers. However, they also appear to be locked in entrepreneurship because of their anticipated lower value......This paper challenges the conventional belief that entrepreneurship is an unstable career path. Using longitudinal matched employer–employee data from Denmark, the analysis reveals that a transition to entrepreneurship decreases individual's employment turnover tendency. Three explanations...... in the labour market and because of their personal attachment to the venture. The counter-intuitive finding – entrepreneurship yields greater employment stability – only holds with respect to subsequent transitions to wagework and not for new venture founding. The results have implications for our understanding...

  2. Liability in Employment Law

    OpenAIRE

    Lang, Roman

    2006-01-01

    97 Liability in labour law Summary This diploma paper analyzes liability in labour law with focus on liability for damage. At first the diploma paper introduces conception of liability in general and idea of liability in labour law considering different position of employee and employer in labour relations. The diploma paper then enumerates the types of labour-law liability. The next chapter concentrates on liability for damage. This chapter describes characteristic features of liability for ...

  3. Work and Employment

    OpenAIRE

    De Poorter, Mathieu

    2012-01-01

    The social and solidarity economy (SSE) and its ties to the questions of employment and work are discussed here from the perspective of enterprises and organisations of the SSE and their efforts to create decent work, as defined by the International Labour Organisation. Enterprises and organisations of the SSE are analysed under the four dimensions that define decent work, namely: The guarantee of labour rights, and the promotion of the application and respect for the (fundamental) working st...

  4. Soldiers’ employment attitude and employability: An exploratory study

    Directory of Open Access Journals (Sweden)

    Peng Gao

    2015-04-01

    Full Text Available Purpose: Nowadays it is very difficult for Chinese retired soldiers to find proper jobs, and the primary reason is the significant gap between job requirements and soldiers owned job skills. Therefore, it is very important to improve the soldiers’ job skills and enhance their understanding of employment.Design/methodology/approach: This paper expands the study scope from the soldiers’ job skills to the employability, initiatively introduces the employment attitude which has obvious impact on the employment of soldiers, and analyses the influence that employment attitude can play on employability. At last, this paper develops statistical method to find the relationship between soldiers’ employment attitude and employability.Findings: The empirical analysis shows that soldiers’ employment attitude has the positive linkage with employability, which makes the employment attitude a measurable variable for the employability rather than an absolute standard.Research limitations/implications: According to the research purpose, more variables should be considered in the model, consequently, there are only three indicators to describe solders’ employment attitude and four indicators to describe solders’ employability.Originality/value: This paper takes research on soldiers’ employability in a new perspective. The soldiers’ employment attitude is served as the entry point, showing the influence that soldiers’ employment attitude has on employability.

  5. Environment, employment and development

    International Nuclear Information System (INIS)

    Bhalla, A.S.

    1992-01-01

    It is generally recognised that the question of sustainable development is a global problem, emphasizing the increasingly interdependent nature of relationships among nations. Solutions to the problem are as much political as they are economic and technological. Notwithstanding the deepening and widening of the debate on sustainable development, its implications for employment - a major concern of the ILO under its World Employment Programme - have remained largely unexplored. This volume, therefore, has a very modest objective, namely to place the employment question on the policy agenda in the context of the current debate on environment and development. The design of environmental policies should allow for the differences that exist between countries with a high level of development and technological dynamism and those with a low level of development and low technological capability. One must also recognize the costs imposed by adjustment and the consequent distributional impact. In the long term, technology choice plays a crucial role in promoting sustainable development in both industrialized and developing countries. It is not only environment-friendly technologies that need to be developed and diffused; in the case of the least developed countries, technological transformation needs to be accelerated in order to minimise their dependence on natural resources for economic growth. Refs, figs and tabs

  6. Energy investments and employment

    International Nuclear Information System (INIS)

    1993-08-01

    A study was conducted to assess the effect that different energy options would have on provincial and regional employment prospects in British Columbia. Current and future economic and employment patterns were examined to develop a more detailed understanding of the skills, age, gender, location, and other characteristics of British Columbia workers. Over 40 previous studies examining the energy/employment relationship were also reviewed. Based on this review and an analysis of the province's economic and labor conditions, the following conclusions are drawn. Investment in non-energy sectors offers better prospects for reducing unemployment than investment in the energy sector, whether for new supply or improving efficiency. Investments in the energy sector provide fewer jobs than investments in most other sectors of the economy. Among the available electricity supply options, large hydroelectric projects tend to produce the fewest jobs per investment dollar. Smaller thermal projects such as wood residue plants produce the most jobs. If and when more energy is needed in British Columbia, the most cost-effective combination of energy supply and efficiency options will also create the most jobs. Compared to traditional energy supply options, investments in energy efficiency would create about twice as many total jobs, create jobs that better match the skills of the province's unemployed and its population distribution, and create jobs that last longer on the average. Construction-related measures such as improved insulation tend to produce more jobs per investment dollar than the substitution of more energy-efficient equipment. 69 refs., 9 tabs

  7. The Global Network of Optical Magnetometers for Exotic physics (GNOME): A novel scheme to search for physics beyond the Standard Model

    International Nuclear Information System (INIS)

    Pustelny, Szymon; Jackson Kimball, Derek F.; Pankow, Chris; Ledbetter, Micah P.; Wlodarczyk, Przemyslaw; Wcislo, Piotr; Pospelov, Maxim; Smith, Joshua R.; Read, Jocelyn; Gawlik, Wojciech; Budker, Dmitry

    2013-01-01

    A novel experimental scheme enabling the investigation of transient exotic spin couplings is discussed. The scheme is based on synchronous measurements of optical-magnetometer signals from several devices operating in magnetically shielded environments in distant locations (>or similar 100 km). Although signatures of such exotic couplings may be present in the signal from a single magnetometer, it would be challenging to distinguish them from noise. By analyzing the correlation between signals from multiple, geographically separated magnetometers, it is not only possible to identify the exotic transient but also to investigate its nature. The ability of the network to probe presently unconstrained physics beyond the Standard Model is examined by considering the spin coupling to stable topological defects (e.g., domain walls) of axion-like fields. In the spirit of this research, a brief (∝2 hours) demonstration experiment involving two magnetometers located in Krakow and Berkeley (∝9000 km separation) is presented and discussion of the data-analysis approaches that may allow identification of transient signals is provided. The prospects of the network are outlined in the last part of the paper. (copyright 2013 by WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  8. Setup and taking into operation of a highly sensitive 3He magnetometer for a future experiment for the determination of an electric dipole moment of the free neutron

    International Nuclear Information System (INIS)

    Kraft, Andreas

    2012-01-01

    The measurement of the electric dipole moment of the free neutron is directly linked to the question on the accurate determination of the magnetic field conditions inside the nEDM spectrometer. Using in-situ the spin-precession of polarized 3 He, monitored by optically pumped Cs-magnetometers a sensitivity on the femto-tesla-scale can be obtained. At the institute of physics of the University Mainz a 3 He/Cs-test facility was built to investigate the readout of 3 He-spin-precession with a lamp-pumped Cs-magnetometer. Additionally, an ultra-compact and transportable polarizer unit was developed and installed in Mainz, which polarizes 3 He gas up to 55 % of polarization before the compressed gas is delivered to two sandwich magnetometer cells inside the EDM chamber. This theses will present some results of the first successful test of the polarizer unit in January 2012. 3 He was polarized in the ultra compact polarizer unit and transferred via guiding fields into a 4 layer mu-metal shield, where the free spin precession was detected with a lamp pumped Cs-magnetometer.

  9. Employment opportunities for the disabled

    NARCIS (Netherlands)

    Delsen, L.W.M.

    1996-01-01

    Policy makers in the OECD Member States have developed quite different programmes and institutional arrangements to create and promote employment opportunities for the disabled. These policy approaches include legal interventions, employment support services, financial support of open employment and

  10. Effect of low-frequency ambient magnetic fields on the control unit and RF head of a commercial SQUID magnetometer

    Science.gov (United States)

    Marcus, C. M.

    1984-01-01

    The control unit and RF head of the SHE model 330XRFSQUID system are shown to be sensitive to ambient ac magnetic fields below 1 HZ, which cause the appearance of false signals corresponding to a magnetometer signal of 0.000001 phi(0) per gauss of field applied. The control unit shows a sensitivity that is linear with frequency, suggesting that the signal is generated by Faraday induction. In contrast, the RF head response is independent of frequency and shows a strong second-harmonic coversion. This response may be due to the magnetic field sensitivity of the ferrite core inductor in the tuned amplifier of the RF head. These signals induced by ambient fields are a potential source of error in Stanford's Relativity Gyroscope experiment, which uses SQUID's on board a rolling satellite as part of the gyroscope readout system. The extent of the magnetic field sensitivity in these components necessitates the use of additional magnetic shielding aboard the satellite.

  11. Remote sensing of the plasmasphere mass density using conjugate magnetometer chains SAMBA, MEASURE, and McMAC

    Science.gov (United States)

    Zesta, E.; Boudouridis, A.; Moldwin, M.; Chi, P. J.; Jorgensen, A. M.; McCarthy, N. M.

    2010-12-01

    The SAMBA (South American Meridional B-field Array) chain is a Southern Hemisphere meridional chain of 12 magnetometers, 11 of them at L=1.1 to L=2.5 along the coast of Chile and in the Antarctica peninsula, and one auroral station along the same meridian. SAMBA is ideal for low and mid-latitude studies of geophysical events and ULF waves. The MEASURE (Magnetometers along the Eastern Atlantic Seaboard for Undergraduate Research and Education) and McMAC (Mid-continent Magnetoseismic Chain) chains are Northern Hemisphere meridional chains in the same local time as SAMBA, but cover low to sub-auroral latitudes. SAMBA is partly conjugate to MEASURE and McMAC chains, offering unique opportunities for inter-hemispheric studies. We use 5 of the SAMBA stations and an even larger number of conjugate stations from the Northern hemisphere to determine the field line resonance (FLR) frequency of closely spaced flux tubes in the inner magnetosphere. Standard inversion techniques are used to derive the equatorial mass density of these flux tubes from the FLRs. We thus yield the mass density distribution of the plasmasphere for specific events and compare our results with the empirical model of Berube and Moldwin [2005]. Limited prior results have shown that the derived mass density of closely spaced flux tubes, from L=1.6 to L=2.5, drops at a rate that cannot be predicted by any of the existing models or agree with past observations. We now assemble a much larger latitude range with better latitudinal spacing, that allow for more accurate comparisons. We also compare our derived mass density distribution with that predicted by the FLIP thermosphere-ionosphere model. We find that for moderate activity the model determined FLR radial distribution is in excellent agreement with the observed distribution.

  12. In situ magnetic compensation for potassium spin-exchange relaxation-free magnetometer considering probe beam pumping effect

    Energy Technology Data Exchange (ETDEWEB)

    Fang, Jiancheng; Wang, Tao, E-mail: wangtaowt@aspe.buaa.edu.cn; Quan, Wei; Yuan, Heng; Li, Yang [School of Instrument Science and Opto-Electronics Engineering, Beihang University, Beijing 100191 (China); Zhang, Hong; Zou, Sheng [School of Instrument Science and Engineering, Southeast University, Nanjing 210096 (China)

    2014-06-15

    A novel method to compensate the residual magnetic field for an atomic magnetometer consisting of two perpendicular beams of polarizations was demonstrated in this paper. The method can realize magnetic compensation in the case where the pumping rate of the probe beam cannot be ignored. In the experiment, the probe beam is always linearly polarized, whereas, the probe beam contains a residual circular component due to the imperfection of the polarizer, which leads to the pumping effect of the probe beam. A simulation of the probe beam's optical rotation and pumping rate was demonstrated. At the optimized points, the wavelength of the probe beam was optimized to achieve the largest optical rotation. Although, there is a small circular component in the linearly polarized probe beam, the pumping rate of the probe beam was non-negligible at the optimized wavelength which if ignored would lead to inaccuracies in the magnetic field compensation. Therefore, the dynamic equation of spin evolution was solved by considering the pumping effect of the probe beam. Based on the quasi-static solution, a novel magnetic compensation method was proposed, which contains two main steps: (1) the non-pumping compensation and (2) the sequence compensation with a very specific sequence. After these two main steps, a three-axis in situ magnetic compensation was achieved. The compensation method was suitable to design closed-loop spin-exchange relaxation-free magnetometer. By a combination of the magnetic compensation and the optimization, the magnetic field sensitivity was approximately 4 fT/Hz{sup 1/2}, which was mainly dominated by the noise of the magnetic shield.

  13. Compact, ultra-low vibration, closed-cycle helium recycler for uninterrupted operation of MEG with SQUID magnetometers

    Science.gov (United States)

    Wang, Chao; Sun, Limin; Lichtenwalter, Ben; Zerkle, Brent; Okada, Yoshio

    2016-06-01

    A closed-cycle helium recycler was developed for continuous uninterrupted operation for magnetometer-based whole-head magnetoencephalography (MEG) systems. The recycler consists of a two stage 4 K pulse-tube cryocooler and is mounted on the roof of a magnetically shielded room (MSR). A flexible liquid helium (LHe) return line on the recycler is inserted into the fill port of the MEG system in the MSR through a slotted opening in the ceiling. The helium vapor is captured through a line that returns the gas to the top of the recycler assembly. A high-purity helium gas cylinder connected to the recycler assembly supplies the gas, which, after it is liquefied, increases the level of LHe in the MEG system during the start-up phase. No storage tank for evaporated helium gas nor a helium gas purifier is used. The recycler is capable of liquefying helium with a rate of ∼17 L/d after precooling the MEG system. It has provided a fully maintenance-free operation under computer control for 7 months without refill of helium. Although the recycler is used for single-orientation operation at this initial testing site, it is designed to operate at ±20° orientations, allowing the MEG system to be tilted for supine and reclining positions. Vibration of the recycler is dampened to an ultra-low level by using several vibration isolation methods, which enables uninterrupted operation during MEG measurements. Recyclers similar to this system may be quite useful even for MEG systems with 100% magnetometers.

  14. Development of Search-Coil Magnetometer for Ultra Low Frequency (ULF) Wave Observations at Jang Bogo Station in Antarctica

    Science.gov (United States)

    Lee, J. K.; Shin, J.; Kim, K. H.; Jin, H.; Kim, H.; Kwon, J.; Lee, S.; Jee, G.; Lessard, M.

    2016-12-01

    A ground-based bi-axial search-coil magnetometer (SCM) has been devloped for observation of time-varying magnetic fields (dB/dt) in the Ultra Low Frequency (ULF) range (a few mHz up to 5 Hz) to understand magnetosphere-ionosphere coupling processes. The SCM consists of magnetic sensors, analog electronics, cables and data acquisition system (DAQ). The bi-axial magnetic sensor has coils of wire wound around a mu-metal cores, each of which measures magnetic field pulsations in the horizontal components, geomagnetic north-south and east-west, respectively. The analog electronics is designed to control the cut-off frequency of the instrument and to amplify detected signals. The DAQ has a 16 bit analog to digital converter (ADC) at the user defined rate of 10 Hz. It is also equipped with the Global Positioning System (GPS) and Network Time Protocol (NTP) for time synchronization and accuracy. We have carried out in-lab performance tests (e.g., frequency response, noise level, etc) using a magnetically shielded case and a field-test in a magnetically quiet location in South Korea. During the field test, a ULF Pi 2 event has been observed clearly. We also confirmed that it was a substorm activity from a fluxgate magnetometer data at Mineyama (35°57.3'N, 135°05'E, geographic). The SCM will be installed and operated at Jang Bogo Antarctic Research Station (74°37.4'S, 164°13.7'E, geographic) on Dec. 2016. The geomagnetic latitude of the station is similar to that of the US McMurdo station (77°51'S, 166°40'E, geographic), both of which are typically near the cusp region. Thus, we expect that the SCM can provide useful information to understand ULF wave propagation characteristics.

  15. Leaving Employment to Entrepreneurship

    DEFF Research Database (Denmark)

    Rocha, Vera; Carneiro, Anabela; Varum, Celeste

    : the relative inattention paid to other human resources beyond the founder, and the hetero-geneous context where employee startups may be established. We use a rich matched employer-employee dataset for Portugal, and estimate a multi-stage model addressing the issues of self-selection in entrepreneurship...... outcomes of arrival fi rms, and also for developing theories on labor markets for entrepreneurship. It also constitutes an important step towards unpacking the mechanisms through which mobile human capital affects the performance of receiving firms....

  16. Challenging Scandinavian employment relations

    DEFF Research Database (Denmark)

    Ibsen, Christian Lyhne; Larsen, Trine Pernille; Madsen, Jørgen Steen

    2011-01-01

    and employment relations in the Danish, Norwegian and Swedish public sector. In this paper, we argue that although differences exist across the Scandinavian countries, it is evident that they have managed to adopt and implement NPM-inspired reforms without dismantling their universal welfare services and strong......Building on the convergence/divergence approach, this paper examines whether recent new public management (NPM) inspired reforms entailing inter alia cutbacks in the public sector, marketisation and management by performance measures have had significant implications for service provision...... traditions of collective bargaining in the public sector. However, this restructuring is taking its toll on the work environment....

  17. Graduate Employability: A Conceptual Framework for Understanding Employers' Perceptions

    Science.gov (United States)

    Cai, Yuzhuo

    2013-01-01

    This study provides a conceptual framework for understanding what employers think about the value of graduates with similar educational credentials in the workplace (their employability), using insights from the new institutionalism. In this framework, the development of employers' beliefs about graduates' employability is broken into a number of…

  18. 10. The surface and interior of venus

    Science.gov (United States)

    Masursky, H.; Kaula, W.M.; McGill, G.E.; Pettengill, G.H.; Phillips, R.J.; Russell, C.T.; Schubert, G.; Shapiro, I.I.

    1977-01-01

    Present ideas about the surface and interior of Venus are based on data obtained from (1) Earth-based radio and radar: temperature, rotation, shape, and topography; (2) fly-by and orbiting spacecraft: gravity and magnetic fields; and (3) landers: winds, local structure, gamma radiation. Surface features, including large basins, crater-like depressions, and a linear valley, have been recognized from recent ground-based radar images. Pictures of the surface acquired by the USSR's Venera 9 and 10 show abundant boulders and apparent wind erosion. On the Pioneer Venus 1978 Orbiter mission, the radar mapper experiment will determine surface heights, dielectric constant values and small-scale slope values along the sub-orbital track between 50??S and 75??N. This experiment will also estimate the global shape and provide coarse radar images (40-80 km identification resolution) of part of the surface. Gravity data will be obtained by radio tracking. Maps combining radar altimetry with spacecraft and ground-based images will be made. A fluxgate magnetometer will measure the magnetic fields around Venus. The radar and gravity data will provide clues to the level of crustal differentiation and tectonic activity. The magnetometer will determine the field variations accurately. Data from the combined experiments may constrain the dynamo mechanism; if so, a deeper understanding of both Venus and Earth will be gained. ?? 1977 D. Reidel Publishing Company.

  19. Life Sciences and employability

    Directory of Open Access Journals (Sweden)

    Wynand J. Boshoff

    2012-03-01

    Full Text Available This article addresses unemployment in rural areas. South Africa is also characterised by skills shortage and high unemployment figures, especially in rural areas as compared to urban areas. The institutional reality of education is that every rural village hosts a high school which is primarily engaged in preparing learners for further studies, whilst the Further Training Colleges (previously known as technical colleges are mainly located in the larger centres. It is with this scenario as a backdrop that the possible role of high schools to alleviate the problem is being argued. It is clear that rural employers do not expect from school leavers to be in possession of applicable knowledge, but rather to be in possession of the ability as well as certain personal characteristics that would make them employable. Unfortunately, however, this is not always found in young persons who have completed their schooling successfully. Life Sciences educators can render a valuable service should certain nontraditional approaches be incorporated into the teaching practice. This will enable them to contribute to solving one of South Africa’s serious problems.

  20. Employment funding under review.

    Science.gov (United States)

    1998-01-01

    In February 1998, the Vietnam Women's Union (VWU) hosted a conference to review experience with the National Employment Program (NEP) that was instituted in 1993 to fund projects that create jobs. The 1.5 billion VND in funding distributed by the VWU that year has increased to 21 billion VND in 1997 and has supported 559 projects in 61 provinces and cities, creating 139,162 jobs. The 14 mountainous provinces have benefitted from 140 projects implemented with 4 billion VND in loans to ethnic minorities. In one case, a revolving loan fund of 100 million VND recovered most of the principle loaned as well as 54 million VND in interest. In another, investment of 70 million VND generated 48 million VND in income in a single year. The availability of the loans has allowed families to rise from chronic poverty as women have generated employment and income for their families. In order to expand, however, the program needs more funding and more cooperation from the State Treasury, and VWU members need training in order to be able to manage large projects.

  1. Maternal employment and birth outcomes

    DEFF Research Database (Denmark)

    Wüst, Miriam

    I use Danish survey and administrative data to examine the impact of maternal employment during pregnancy on birth outcomes. As healthier mothers are more likely to work and health shocks to mothers may impact employment and birth outcomes, I combine two strategies: First, I control extensively f...... explanation, namely, that exclusion from employment may stress mothers in countries with high-female employment rates....

  2. Employability Skills Assessment Tool Development

    Science.gov (United States)

    Rasul, Mohamad Sattar; Rauf, Rose Amnah Abd; Mansor, Azlin Norhaini; Puvanasvaran, A. P.

    2012-01-01

    Research nationally and internationally found that technical graduates are lacking in employability skills. As employability skills are crucial in outcome-based education, the main goal of this research is to develop an Employability Skill Assessment Tool to help students and lecturers produce competent graduates in employability skills needed by…

  3. Authenticity in Employment Relations

    DEFF Research Database (Denmark)

    Tackney, Charles Thomas

    analysis should complement and support corporate social responsibility, management spirituality, authentic leadership / authentic follower, and other secular research by offering a research methods bridge between empirically grounded theology and secular studies, with the common goal of improving workplace...... of the concept in Western culture, philosophy, and management studies, Religious Society of Friends (Quaker) and Roman Catholic social teachings are investigated for positively correlative data to help develop the criterion variable. From the literature review of concept and historical data in both traditions......This research takes up the concept of authenticity as a criterion variable for theology of the workplace analysis, a domain which explores employment parameters in light of religious teaching on the social question at national, organizational or firm-specific levels. Following a review...

  4. Fixed term employment

    International Nuclear Information System (INIS)

    Durant, B.W.; Schonberner, M.J.

    1999-01-01

    A series of brief notes were included with this presentation which highlighted certain aspects of contract management. Several petroleum companies have realized the benefits of taking advantage of contract personnel to control fixed G and A, manage the impacts on their organization, contain costs, to manage termination costs, and to fill gaps in lean personnel rosters. An independent contractor was described as being someone who is self employed, often with a variety of work experiences. The tax benefits and flexibility of contractor personnel were also described. Some liability aspects of hiring an independent contractor were also reviewed. The courts have developed the following 4 tests to help determine whether an individual is an employee or an independent contractor: (1) the control test, (2) the business integration test, (3) specific result test, and (4) the economic reality test

  5. Authenticity in Employment Relations

    DEFF Research Database (Denmark)

    Tackney, Charles Thomas

    2018-01-01

    Authenticity is developed and deployed as a criterion variable for a theology of the workplace inquiry that combines theory and methodological development with data analysis. The goal is to show that social science method can offer an empirically valid, prophetic dimension to the study of employm......Authenticity is developed and deployed as a criterion variable for a theology of the workplace inquiry that combines theory and methodological development with data analysis. The goal is to show that social science method can offer an empirically valid, prophetic dimension to the study...... of employment and work parameters in light of religious teachings on the social question at national, organizational, or firm-specific levels. The function of a criterion variable is described, noting that the switch from a dependent variable approach introduces an open-system dynamism to social science...... theology and allied fields for the common cause of assessing authenticity in firm, organization, and higher system functions....

  6. Authenticity in Employment Relations

    DEFF Research Database (Denmark)

    Tackney, Charles Thomas

    analysis should complement and support corporate social responsibility, management spirituality, authentic leadership / authentic follower, and other secular research by offering a research methods bridge between empirically grounded theology and secular studies, with the common goal of improving workplace......This research takes up the concept of authenticity as a criterion variable for theology of the workplace analysis, a domain which explores employment parameters in light of religious teaching on the social question at national, organizational or firm-specific levels. Following a review...... of the concept in Western culture, philosophy, and management studies, Religious Society of Friends (Quaker) and Roman Catholic social teachings are investigated for positively correlative data to help develop the criterion variable. From the literature review of concept and historical data in both traditions...

  7. Development of Next-Generation Borehole Magnetometer and Its Potential Application in Constraining the Magnetic Declination of Oman Samail Ophiolite at ICDP Drill Sites

    Science.gov (United States)

    Lee, S. M.; Parq, J. H.; Kim, H.; Moe, K.; Lee, C. S.; Kanamatsu, T.; Kim, K. J.; Bahk, K. S.

    2017-12-01

    Determining the azimuthal orientation of core samples obtained from deep drilling is extremely difficult because the core itself could have rotated during drilling operations. Several indirect methods have been devised to address this issue, but have certain limitations. Thus it is still a challenge to determine the azimuthal orientation consistently over the entire length of the hole. Provided that the recovery rate is high and thus all the other magnetic properties such as magnetization intensity and inclination are measured from the recovered cores, one possible method for ascertaining magnetic declination information is to measure the magnetic field inside the empty borehole and invert for the best fitting declination. However, there are two major problems: one is that present-day borehole magnetometers are not precise enough to resolve changes in direction of magnetization, and the other is that in most rock drilling experiments the rate of recovery is low. To overcome the first major problem which is technical, scientists from Korea and Japan jointly conducted the development for the next-generation borehole magnetometer, namely 3GBM (3rd Generation Borehole Magnetometer). The borehole magnetometer which uses fiber-optic laser gyro promises to provide accurate information on not only the magnetic field itself but also the orientation of the instrument inside the borehole. Our goal is to deploy this borehole magnetometer in the ICDP Oman Drilling Project Phase 2 drilling experiment early 2018. The site may be suitable for the investigation because, as recent Phase 1 of the Oman Samail Ophiolite drilling has demonstrated, the recovery rate was very high. Also the post-drilling measurements onboard DV Chikyu have shown that much of the recovered samples has moderate magnetization intensity on the order of 0.1 and 1 A/m. Here, we present the results of numerical simulation of magnetic field inside the borehole using finite element method to show that magnetic

  8. Employment relations, flexibility and risk

    DEFF Research Database (Denmark)

    Jensen, Carsten Strøby

    Employment relations literature often distinguishes between social democratic/corporatist models of employment relations and liberal models of employment relations as they are seen as opposite or at least different ways of organizing labor markets. They are often characterized as having very...... different risk profiles in terms of relationships between employees, employers, and the state. Low levels of labor market regulation very often characterize the liberal models of employment relations as we know them from, for instance, the USA and the UK. This means that employment conditions are very often...

  9. 29 CFR 779.19 - Employer, employee, and employ.

    Science.gov (United States)

    2010-07-01

    ... RETAILERS OF GOODS OR SERVICES General Some Basic Definitions § 779.19 Employer, employee, and employ. The... of oppressive child labor. The Act provides its own definitions of “employer,” “employee”, and... particular employee. It should also be noted that “employer”, “enterprise”, and “establishment” are not...

  10. A Conceptual Understanding of Employability: The Employers' View in Rwanda

    Science.gov (United States)

    Bamwesiga, Penelope Mbabazi

    2013-01-01

    Many governments believe that investing in human capital should increase citizens' employability, which is why it is often presented as a solution to the problems of knowledge-based economies and societies, rising unemployment rates and economic competiveness. The aim of this study is to understand employers' views regarding the employability of…

  11. Consumer and Employer Strategies for Overcoming Employment Barriers. Technical Report.

    Science.gov (United States)

    Crudden, Adele; Williams, Wendy; McBroom, Lynn W.; Moore, J. Elton

    This report on strategies for overcoming employment barriers for persons with visual impairments summarizes comments and suggestions of 7 focus groups comprised of either consumers (n=49) or employers (n=19). The report first reviews the literature concerning employment barriers and how consumers in previous studies suggested these barriers be…

  12. Low-frequency noise in high-Tc superconductor Josephson junctions, SQUIDs, and magnetometers

    Energy Technology Data Exchange (ETDEWEB)

    Miklich, Andrew Hostetler [Univ. of California, Berkeley, CA (United States)

    1994-05-01

    Design and performance of high-Tc dc superconducting quantum interference devices (SQUEDs), junctions that comprise them, and magnetometers made from them are described, with attention to sources of 1/f noise. Biepitaxial junctions are found to have large levels of critical current fluctuations which make them unsuitable for low-noise SQUIDS; this suggests a poorly connected interface at the grain boundary junction. SQUIDs from bicrystal junctions have levels of critical current noise controllable using bias current reversal techniques which leave the noise white down to frequencies of a few Hz. A SQUID with an energy resolution of 1.5 x 10-30 J Hz-1 at 1 Hz is reported. Magnetometers in which a (9 mm)2 pickup loop is directly coupled to a SQUID body have achieved field resolutions of 93 fT Hz-1/2 down to frequencies below I Hz, improving to 39 fT Hz-1/2 at 1 Hz with the addition of a 50mm-diameter single-turn flux transformer. Poor coupling to pickup loop makes it difficult to satisfy competing goals of high field resolution and small detector size necessary for multichannel biomagnetic imaging. Improved coupling is demonstrated by the use of multiturn-input-coil flux transformers, and a resolution of 35 fT Hz-1/2 in the white noise region is reported with a (10 mm)2 pickup loop. However, additional 1/f noise from processed multilayer structures in the transformer limits the resolution at 1 Hz to 114 fT Hz-1/2. High-Tc SQUIDs exhibit additional 1/f noise when cooled in a nonzero static magnetic field because of additional flux vortices trapped in the film, with the noise power at 1 Hz typically increasing by a factor of 10--20 in a field of 0.05mT (0.5 G). Finally, a SQUID-based voltmeter with a resolution of 9.2 pV.Hz-1/2 at 10 Hz (24 pV Hz-1/2 at 1 Hz) is described.

  13. Employment challenges in the future

    DEFF Research Database (Denmark)

    Rimmer, Nina Roehr

    2011-01-01

    Discussion of challenges in employment challenges in Europe and a brief discription of the Danish flexicurity system......Discussion of challenges in employment challenges in Europe and a brief discription of the Danish flexicurity system...

  14. Veterans' Employment and Training Service

    Science.gov (United States)

    ... Engage Facebook Twitter Instagram RSS Email Share Veterans' Employment and Training Service (VETS) Menu About VETS Who ... Tweets about from:@VETS_DOL Tweets by @USDOL Employment Initiatives Contact your local American Job Center for ...

  15. Single-employer Pension Plans

    Data.gov (United States)

    Pension Benefit Guaranty Corporation — This spreadsheet lists the active single-employer pensions plans insured by PBGC. Plans are identified by name, employer identification number (EIN) and plan number...

  16. An atomic spin precession detection method based on electro-optic modulation in an all-optical K–Rb hybrid atomic magnetometer

    International Nuclear Information System (INIS)

    Hu, Yanhui; Liu, Xuejing; Li, Yang; Yao, Han; Dai, Lingling; Yang, Biyao; Ding, Ming

    2017-01-01

    We present an ultrahigh-sensitivity electro-optic modulator (EOM) detection method for detecting the atomic Larmor precession in an all-optical K–Rb hybrid atomic magnetometer operating in the spin-exchange relaxation-free regime. A magnetic field sensitivity of ∼10 f T Hz −1/2 has been achieved by optimizing the probe laser parameters and the EOM modulation conditions, which is comparable to that with the Faraday modulation method and has a better performance than the balanced polarimetry method in the low frequency range. The EOM detection method in the atomic magnetometer presents several advantages, such as simple structure, no extra magnetic noise, moderate thermal effect, high measurement sensitivity and reliable stability. It is demonstrated to be feasible for the improved compactness and simplicity of atomic magnetic field measurement devices in the future. (paper)

  17. Daytime, low latitude, vertical ExB drift velocities, inferred from ground-based magnetometer observations in the Peruvian, Philippine and Indian longitude sectors under quiet and disturbed conditions

    CERN Document Server

    Anderson, D; Chau, J; Yumoto, K; Bhattacharya, A; Alex, S

    2006-01-01

    Daytime, low latitude, vertical ExB drift velocities, inferred from ground-based magnetometer observations in the Peruvian, Philippine and Indian longitude sectors under quiet and disturbed conditions

  18. Employment Impact of Electronic Business.

    Science.gov (United States)

    Hecker, Daniel E.

    2001-01-01

    Electronic business is stimulating employment in some sectors across industries, such as computer-related and customer service occupations, and diminishing employment in others, such as administrative support and marketing/sales. Similarly, employment impacts will vary by industry. (Contains 56 notes and references.) (SK)

  19. Analysis of initial Juno magnetometer data using a new method of magnetic field analysis

    Science.gov (United States)

    Moore, Kimberly; Bloxham, Jeremy; Connerney, John; Jørgensen, John; Merayo, José

    2017-04-01

    Data from the first perijove pass (PJ1) of Juno at Jupiter suggests that Jupiter's magnetic field is both much stronger and more spatially complex than indicated by previous models such as VIP4 [Connerney et al., 1998]. Here we apply a new method of magnetic field analysis in order to gain an indication of what magnetic field structures may explain these intriguing observations. Our method cosnsists of three steps: first, we remove VIP4 from the Juno observations to create a residual dataset; second, we use an elastic net [Zou and Hastie, 2004] to fit a set of magnetic pixels on a spherical surface at a given radius to this residual dataset; and finally, we add the resulting magnetic pixels back onto VIP4, creating an enhanced VIP. The set of magnetic pixels consists of approximately 10,000 nearly uniform and mostly hexagonal elements on a spherical surface (at say r= 1.0 Rj or 0.85 Rj). Crucially in this method, the elastic net, which is a combination of L1 and L2 regularizations, ensures that magnetic pixels, or groups of correlated magnetic pixels, will only be nonzero if required by the data. The structure we obtain suggests the possible presence of both equatorial spots, as might result from flux expulsion, and low polar flux, as might result from the effect of a tangent cylinder.

  20. Setup and taking into operation of a highly sensitive {sup 3}He magnetometer for a future experiment for the determination of an electric dipole moment of the free neutron; Aufbau und Inbetriebnahme eines hochsensitiven {sup 3}He-Magnetometers fuer ein zukuenftiges Experiment zur Bestimmung eines elektrischen Dipolmoments des freien Neutrons

    Energy Technology Data Exchange (ETDEWEB)

    Kraft, Andreas

    2012-12-20

    The measurement of the electric dipole moment of the free neutron is directly linked to the question on the accurate determination of the magnetic field conditions inside the nEDM spectrometer. Using in-situ the spin-precession of polarized {sup 3}He, monitored by optically pumped Cs-magnetometers a sensitivity on the femto-tesla-scale can be obtained. At the institute of physics of the University Mainz a {sup 3}He/Cs-test facility was built to investigate the readout of {sup 3}He-spin-precession with a lamp-pumped Cs-magnetometer. Additionally, an ultra-compact and transportable polarizer unit was developed and installed in Mainz, which polarizes {sup 3}He gas up to 55 % of polarization before the compressed gas is delivered to two sandwich magnetometer cells inside the EDM chamber. This theses will present some results of the first successful test of the polarizer unit in January 2012. {sup 3}He was polarized in the ultra compact polarizer unit and transferred via guiding fields into a 4 layer mu-metal shield, where the free spin precession was detected with a lamp pumped Cs-magnetometer.

  1. Measurement of g using a magnetic pendulum and a smartphone magnetometer

    Science.gov (United States)

    Pili, Unofre; Violanda, Renante; Ceniza, Claude

    2018-04-01

    The internal sensors in smartphones for their advanced add-in functions have also paved the way for these gadgets becoming multifunctional tools in elementary experimental physics. For instance, the acceleration sensor has been used to analyze free-falling motion and to study the oscillations of a spring-mass system. The ambient light sensor on the other hand has been proven to be a capable tool in studying an astronomical phenomenon as well as in measuring speed and acceleration. In this paper we present an accurate, convenient, and engaging use of the smartphone magnetic field sensor to measure the acceleration due to gravity via measurement of the period of oscillations (simply called "period" in what follows) of a simple pendulum. Measurement of the gravitational acceleration via the simple pendulum is a standard elementary physics laboratory activity, but the employment of the magnetic field sensor of a smartphone device in measuring the period is quite new and the use of it is seen as fascinating among students. The setup and procedure are rather simple and can easily be replicated as a classroom demonstration or as a regular laboratory activity.

  2. Employment status, employment functioning, and barriers to employment among VA primary care patients.

    Science.gov (United States)

    Zivin, Kara; Yosef, Matheos; Levine, Debra S; Abraham, Kristen M; Miller, Erin M; Henry, Jennifer; Nelson, C Beau; Pfeiffer, Paul N; Sripada, Rebecca K; Harrod, Molly; Valenstein, Marcia

    2016-03-15

    Prior research found lower employment rates among working-aged patients who use the VA than among non-Veterans or Veterans who do not use the VA, with the lowest reported employment rates among VA patients with mental disorders. This study assessed employment status, employment functioning, and barriers to employment among VA patients treated in primary care settings, and examined how depression and anxiety were associated with these outcomes. The sample included 287 VA patients treated in primary care in a large Midwestern VA Medical Center. Bivariate and multivariable analyses were conducted examining associations between socio-demographic and clinical predictors of six employment domains, including: employment status, job search self-efficacy, work performance, concerns about job loss among employed Veterans, and employment barriers and likelihood of job seeking among not employed Veterans. 54% of respondents were employed, 36% were not employed, and 10% were economically inactive. In adjusted analyses, participants with depression or anxiety (43%) were less likely to be employed, had lower job search self-efficacy, had lower levels of work performance, and reported more employment barriers. Depression and anxiety were not associated with perceived likelihood of job loss among employed or likelihood of job seeking among not employed. Single VA primary care clinic; cross-sectional study. Employment rates are low among working-aged VA primary care patients, particularly those with mental health conditions. Offering primary care interventions to patients that address mental health issues, job search self-efficacy, and work performance may be important in improving health, work, and economic outcomes. Published by Elsevier B.V.

  3. Accuracy enhancement of magnetic field distribution measurements within a large cell spin-exchange relaxation-free magnetometer

    Science.gov (United States)

    Gusarov, Alexander; Ben-Amar Baranga, Andrei; Levron, David; Shuker, Reuben

    2018-04-01

    The factorial design technique is implemented to achieve greater accuracy in the determination of magnetic field distribution within a single cell of spin-exchange relaxation-free atomic magnetometer. Three-dimensional magnetic field distribution within a single vapor cell can be found by consecutively pumping, layer by layer, all the cell volumes perpendicular to the probe laser beam, detected by a photodiode array. Thus each element of the array collects information about the magnetic field in the small volume (voxel) which forms when the corresponding part of the probe beam and optically pumped layer cross. One of the most effective ways to enhance measurement accuracy is repeated pumping of the layers and averaging the measured results. However, the measurement time is multiplied several times due to the repeated scanning of the cell volume. The suggested technique enables increased measurement accuracy of each voxel while preserving the number of measurements. Magnetic field distribution is determined by the illumination of the cell layers one by one or simultaneously, according to a special algorithm, with subsequent multifactorial analysis of the obtained results.

  4. Penggunaan Accelerometer dan Magnetometer pada Sistem Real Time Tracking Indoor Position untuk Studi Kasus Pada Gedung Teknik Informatika ITS

    Directory of Open Access Journals (Sweden)

    Dinar Winia Mahandhira

    2017-01-01

    Full Text Available Indoor Positioning System (IPS menggunakan perangkat mobile seperti smartphone masih menjadi permasalahan yang menantang. Seperti GPS yang tidak bekerja secara akurat di dalam gedung, IPS juga memiliki kelemahan yaitu sangat bergantung pada infrastruktur gedung seperti sinyal WiFi yang terkadang tidak tersebar secara merata di seluruh bagian gedung, sehingga membuat sistem ini terkadang tidak dapat bekerja secara optimal dan real time di setiap bagian gedung. Untuk itulah dikembangkan IPS yang menggunakan sensor gerak seperti accelerometer dan magnetometer sebagai tambahan untuk melakukan update posisi secara real time dengan mendeteksi langkah dan arah hadap pengguna saat berjalan. Pertama, posisi awal pengguna harus ditentukan terlebih dahulu misalnya menggunakan sinyal WiFi yang diproses melalui klasifikasi. Setelah posisi pengguna telah ditentukan, sistem akan mendeteksi pergerakan pengguna secara real time menggunakan sensor gerak. Uji coba dilakukan menggunakan studi kasus gedung Teknik Informatika lantai tiga. Hasil yang diberikan pada saat pengujian memberikan performa yang cukup baik dengan rata-rata persentase akurasi untuk pendeteksian langkah dan estimasi arah hadap pengguna adalah sebesar 94,8% dan 94,48%.

  5. Paleomagnetic inclination and declination from three-component borehole magnetometer data—New insights from logging in the Louisville seamounts

    Science.gov (United States)

    Ehmann, S.; Hördt, A.; Leven, M.; Virgil, C.

    2015-01-01

    We carried out measurements of the magnetic field vector at two sites during Integrated Ocean Drilling Program (IODP) Expedition 330 to the Louisville Seamount Chain. The aim was to impose constraints on the magnetization direction and to contribute to the reconstruction of possible hot spot motion. The measurements were conducted using the Göttingen Borehole Magnetometer (GBM). It comprises three fiber optic gyros (FOG) that can be used to reorient the magnetic field data. To improve accuracy, we are using a new algorithm that combines FOG data and data of two inclinometers. As can be evaluated by comparing downlog and uplog of the measurements, the three-dimensional magnetic field data obtained is of good quality. An interpretation of the magnetic field data using a state of the art method based on horizontal layers yields results inconsistent with measurements of the natural remanent magnetization (NRM) of drill core samples. In the following, we define the magnetization from the horizontal layer as apparent magnetization and develop a new interpretation method based on dipping layers. Our method includes a new approximate forward modeling algorithm and considerably improves the consistency of the borehole measurements and the NRM data. We show that a priori information about the geometry of a layer is required to constrain the inclination and declination of magnetization. Especially the azimuth of a layer and the declination of magnetization cannot be determined separately. Using azimuth and layer dip information from borehole images, we obtain constraints on inclination and declination for one particular layer.

  6. ULTIMA: Array of ground-based magnetometer arrays for monitoring magnetospheric and ionospheric perturbations on a global scale

    Science.gov (United States)

    Yumoto, K.; Chi, P. J.; Angelopoulos, V.; Connors, M. G.; Engebretson, M. J.; Fraser, B. J.; Mann, I. R.; Milling, D. K.; Moldwin, M. B.; Russell, C. T.; Stolle, C.; Tanskanen, E.; Vallante, M.; Yizengaw, E.; Zesta, E.

    2012-12-01

    ULTIMA (Ultra Large Terrestrial International Magnetic Array) is an international consortium that aims at promoting collaborative research on the magnetosphere, ionosphere, and upper atmosphere through the use of ground-based magnetic field observatories. ULTIMA is joined by individual magnetometer arrays in different countries/regions, and the current regular-member arrays are Australian, AUTUMN, CARISMA, DTU Space, Falcon, IGPP-LANL, IMAGE, MACCS, MAGDAS, McMAC, MEASURE, THEMIS, and SAMBA. The Chair of ULTIMA has been K. Yumoto (MAGDAS), and its Secretary has been P. Chi (McMAC, Falcon). In this paper we perform case studies in which we estimate the global patterns of (1) near-Earth currents and (2) magnetic pulsations; these phenomena are observed over wide areas on the ground, thus suitable for the aims of ULTIMA. We analyze these two phenomena during (a) quiet period and (b) magnetic storm period. We compare the differences between these two periods by drawing the global maps of the ionospheric equivalent currents (which include the effects of all the near-Earth currents) and pulsation amplitudes. For ionospheric Sq currents at low latitudes during quiet periods, MAGDAS data covering an entire solar cycle has yielded a detailed statistical model, and we can use it as a reference for the aforementioned comparison. We also estimate the azimuthal wave numbers of pulsations and compare the amplitude distribution of pulsations with the distribution of highly energetic (in MeV range) particles simultaneously observed at geosynchronous satellites.

  7. Natural remanent magnetization and rock magnetic parameters from the North-East Atlantic continental margin : Insights from a new, automated cryogenic magnetometer at the Geological Survey of Norway

    Science.gov (United States)

    Klug, Martin; Fabian, Karl; Knies, Jochen; Sauer, Simone

    2017-04-01

    Natural remanent magnetization (NRM) and rock magnetic parameters from two locations, West Barents Sea ( 71.6°N,16.2°E) and Vestnesa Ridge, NW Svalbard ( 79.0°N, 6.9°E), were acquired using a new, automatically operating cryogenic magnetometer system at the Geological Survey of Norway. The magnetometer setup comprises an automated robot sample feeding, dynamic operation and measurement monitoring, and customised output-to-database data handling. The setup is designed to dynamically enable a variety of parallel measurements with several coupled devices (e.g. balance, MS2B) to effectively use dead-time in between the otherwise time-consuming measurements with the cryogen magnetometer. Web-based access allows remote quality control and interaction 24/7 and enables high sample throughput. The magnetic properties are combined with geophysical, geochemical measurements and optical imaging, both radiographic and colour images, from high-resolution core-logging. The multidisciplinary approach enables determination and interpretation of content and formation of the magnetic fraction, and its development during diagenetic processes. Besides palaeomagnetic age determination the results offer the opportunity to study sediment transformation processes that have implications for the burial and degradation of organic matter. The results also help to understand long and short-term variability of sediment accumulation. Chemical sediment stability is directly linked to environmental and climate variability in the polar marine environment during the recent past.

  8. Concept of self-employment

    OpenAIRE

    Startienė, Gražina; Remeikienė, Rita; Dumčiuvienė, Daiva

    2010-01-01

    The article deals with the theories that explain the growth of self-employment and help to determine the presumptions of the self-employment growth. Self-employment theories are classified to several groups, i.e. the economic and sociological-psychological as well as the “push” and “pull” theories. Economic theories of self-employment interpret financial motives of the person to pursue own business, while sociologicalpsychological theories of self-employment determine non-financial objectives...

  9. Growth, Employment and Structural Change

    DEFF Research Database (Denmark)

    Aggarwal, Aradhna

    2016-01-01

    This paper studies the decomposition of GSDP growth per capita in Punjab via-a-vis 15 other states in India during 1993–94 and 2011–12 in terms of employment and productivity growth. Specifically, it focuses on the role of employment growth and structural change in employment on economic growth...... but structural shifts have paid off well in terms of diversification of the economy and their contribution to labour productivity especially for manufacturing. Overall employment effect had been negative but this was essentially due to contraction in the labour force; the employment rate effect turned out...

  10. The analysis of initial Juno magnetometer data using a sparse magnetic field representation

    DEFF Research Database (Denmark)

    Moore, Kimberly M.; Bloxham, Jeremy; Connerney, John E. P.

    2017-01-01

    Juno's first perijove pass (PJ1; to within 1.06 RJ of Jupiter's center). We calculate the residuals between the vector magnetic field observations and that calculated using the VIP4 spherical harmonic model and fit these residuals using an elastic net regression. The resulting model demonstrates how...... effective Juno's near-surface observations are in improving the spatial resolution of the magnetic field within the immediate vicinity of the orbit track. We identify two features resulting from our analyses: the presence of strong, oppositely signed pairs of flux patches near the equator and weak, possibly...... reversed-polarity patches of magnetic field over the polar regions. Additional orbits will be required to assess how robust these intriguing features are....

  11. The Employer Perspective on Sustainable Employability in the Construction Industry.

    Science.gov (United States)

    Tonnon, Susanne C; van der Veen, Rozan; Westerman, Marjan J; Robroek, Suzan J W; van der Ploeg, Hidde P; van der Beek, Allard J; Proper, Karin I

    2017-01-01

    To determine the measures employers in the construction industry take to promote sustainable employability, the barriers and facilitators that influence implementation and employer needs. Questionnaire among 499 employers and interviews with 17 employers. Employers expressed a need for alternative jobs for workers who can no longer perform physically demanding tasks, as well as means to stimulate proactive employee behavior. Measures frequently targeted the work environment (95%) and employee health (79%), less frequently personal development (63%) and organization (65%). Implementation was influenced by economic factors, rules and regulations, client demands, employee demands, company vision, company culture, and time/manpower/expertise. Implementation of measures aimed at reducing physical load and the promotion of personal development are needed.

  12. Monitoring geospace disturbances through coordinated space-borne and ground-based magnetometer observations

    Science.gov (United States)

    Balasis, Georgios

    2014-05-01

    Recently automated methods of deriving the characteristics of ultra low frequency (ULF) waves in the magnetosphere have been developed (Balasis et al., 2012, 2013), which can be effectively applied to the huge datasets from the new ESA Swarm mission, in order to retrieve, on an operational basis, new information about the near-Earth electromagnetic environment. Processing Swarm measurements with these methods will help to elucidate the processes influencing the generation and propagation of ULF waves, which in turn play a crucial role in magnetospheric dynamics. Moreover, a useful platform based on a combination of wavelet transforms and artificial neural networks has been developed to monitor the wave evolution from the outer boundaries of Earth's magnetosphere through the topside ionosphere down to the surface. Data from a Low Earth Orbit (LEO) satellite (CHAMP) and two magnetospheric missions (Cluster and Geotail) along with three ground-based magnetic networks (CARISMA, GIMA and IMAGE), during the Halloween 2003 magnetic superstorm when the Cluster and CHAMP spacecraft were in good local time (LT) conjunction, are used to demonstrate the potential of the analysis technique in studying wave evolution in detail.

  13. Employment strategy of the Russians

    Directory of Open Access Journals (Sweden)

    Vladimir Borisovich Toreev

    2015-05-01

    Full Text Available During the crisis it is especially important to choose a correct employment strategy. Every employee uses an employment strategy, as he/she selects the direction of long-term employment consciously or intuitively. The choice of strategy is determined by a number of factors shaping the person’s attitudes: health, character, upbringing, education, social environment, institutional environment. The employment strategies of the young people newly entering the labor market differ from lab our strategies of workers. Young people do not have such experience and can plan their life “from scratch”. The Soviet specialists, people who started their career in the planned economy, have their own features of employment strategies. The article describes employment strategies of the Russians

  14. Epilepsy and employment: literature review.

    Science.gov (United States)

    Smeets, Vivian M J; van Lierop, Brigitte A G; Vanhoutvin, Jos P G; Aldenkamp, Albert P; Nijhuis, Frans J N

    2007-05-01

    The aim of this review is to increase understanding of the factors that affect the regular employment positions of people with epilepsy by means of the World Health Organization International Classification of Functioning, Disability, and Health (ICF) model. Thirty-four primary research articles describing factors associated with employment for people with epilepsy are reviewed. People with epilepsy may face a number of complex and interacting problems in finding and maintaining employment. Stigma, seizure severity, and psychosocial variables such as low self-esteem, passive coping style, and low self-efficacy have been implicated as factors that play an important role in predicting employment. Findings demonstrate the need for specific employment training programs. We recommend specific training interventions that focus on increasing the self-efficacy and coping skills of people with epilepsy so that these individuals will be able to accept their disorder and make personal and health-related choices that help them to achieve better employment positions in society.

  15. Business/Employers Influenza Toolkit

    Centers for Disease Control (CDC) Podcasts

    2011-09-06

    This podcast promotes the "Make It Your Business To Fight The Flu" toolkit for Businesses and Employers. The toolkit provides information and recommended strategies to help businesses and employers promote the seasonal flu vaccine. Additionally, employers will find flyers, posters, and other materials to post and distribute in the workplace.  Created: 9/6/2011 by Office of Infectious Diseases, Office of the Director (OD).   Date Released: 9/7/2011.

  16. Caseworker Behavior and Clients' Employability

    DEFF Research Database (Denmark)

    Weatherall, Cecilie Dohlmann; Markwardt, Kristoffer

    empirically looked at the link between caseworker behavior and clients’ employability. A very rich survey dataset on caseworker behavior combined with informative panel data on the caseworker’s client—the unemployed—makes it possible to study the link between caseworker behavior and clients’ job possibilities....... Results show that there is a relationship between caseworker behavior and employment among the unemployed. Especially the employability among the insured unemployed is related to the concepts of coping, and professional distance....

  17. Employer-sponsored pension plans

    OpenAIRE

    Rakonjac-Antić Tatjana N.

    2004-01-01

    Apart from pension plans within social insurance, in developed pension systems there are also available to individuals schemes which may to a large extent ensure a significant part of their total pension. Among them are the following: employer-sponsored pension plans or individual pension plans. The most widely used employer-sponsored pension plan in the USA is 401(k), in which both the employer and the employee contribute to the financing of the pension. These contributions as well as the re...

  18. Employer Branding: an Islamic Perspective

    OpenAIRE

    Norasyikin binti Shaikh Ibrahim

    2016-01-01

    This paper discusses employer branding from an Islamic perspective. Islam is away of life and so do the employer and employee relationship, which strengthensemployer branding in an organization. The definition, importance and processrelated to employer branding are discussed in the context of human resource management, such as job satisfaction and work environment. In addition to that, related human resource management practices such as recruitment andselection were discussed in an ...

  19. Conceptualizing Learning and Employability "Learning and Employability Framework"

    Science.gov (United States)

    Sumanasiri, Erabaddage Gishan Tharanga; Yajid, Mohd Shukri Ab; Khatibi, Ali

    2015-01-01

    Extensive studies have been done on employability and the factors that lead to employability. Previous studies have focused on career development programs, internships, work experience programs, soft-skill development programs, and even university admission criteria which can be considered external factors to university student learning…

  20. University Graduates' Employability, Employment Status, and Job Quality

    Science.gov (United States)

    González-Romá, Vicente; Gamboa, Juan Pablo; Peiró, José M.

    2018-01-01

    We investigated whether a set of indicators of the employability dimensions proposed by Fugate, Kinicki, and Asforth (i.e., career identity, personal adaptability, and human and social capital) are related to university graduates' employment status and five indicators of the quality of their jobs (pay, hierarchical level, vertical and horizontal…

  1. Employment effects of foreign acquisition

    DEFF Research Database (Denmark)

    Bandick, Roger; Karpaty, Patrik

    2011-01-01

    This paper investigates the employment effects of foreign acquisitions in acquired firms in Swedish manufacturing during the 1990s; a period characterized by a dramatic increase in foreign ownership. We find some evidence of positive employment effects in acquired firms and it seems that the empl......This paper investigates the employment effects of foreign acquisitions in acquired firms in Swedish manufacturing during the 1990s; a period characterized by a dramatic increase in foreign ownership. We find some evidence of positive employment effects in acquired firms and it seems...

  2. THE BANGLADESHI EMPLOYMENT SECTOR: EMPLOYER PERSPECTIVES CONCERNING ENGLISH PROFICIENCY

    Directory of Open Access Journals (Sweden)

    Rubina Khan

    2012-07-01

    Full Text Available Abstract: This paper presents a brief summary of a study which was carried out to investigate how employers representing major employment sectors in the Bangladeshi Industry view the skills and English proficiency level of the current employees. Opinions were also solicited on what skills are required for fresh recruits. Semi-structured interviews were conducted with 30 employers representing the major employment sectors in Bangladeshi Industry. Results revealed the importance of English as an indispensible means of communication in the Bangladeshi corporate sector and showed that the business enterprises use extensive amounts of English. It also highlighted that the existent English proficiency of the employees was far below the required proficiency level. Recommendations were made to address the gap and prepare the youth to meet the demands of the global market. Keywords: English proficiency, competency, employability skills, global literacy skills

  3. 20 CFR 404.1003 - Employment.

    Science.gov (United States)

    2010-04-01

    ... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false Employment. 404.1003 Section 404.1003...- ) Employment, Wages, Self-Employment, and Self-Employment Income Employment § 404.1003 Employment. Employment....1010. Section 404.1004 states the general rule on the kinds of work covered as employment. Exceptions...

  4. Conjugate Studies of Pc3-5 ULF Waves Using SAMBA, MEASURE, and McMAC Magnetometer Chains

    Science.gov (United States)

    Sterner, N. L.; Zesta, E.; Boudouridis, A.; Moldwin, M.; Chi, P. J.

    2009-12-01

    The Antarctic continent, the only landmass in the southern polar region, offers the unique opportunity for observations that geomagnetically range from polar latitudes to well into the inner magnetosphere, thus enabling conjugate observations in a wide range of geomagnetic latitudes. The SAMBA (South American Meridional B-field Array) chain is a meridional chain of 12 magnetometers, 11 of them at L=1.1 to L=2.5 along the coast of Chile and in the Antarctica peninsula, and one auroral station along the same meridian. SAMBA is ideal for low and mid-latitude studies of geophysical events and ULF waves. It is conjugate to the northern hemisphere MEASURE and McMAC chains, offering unique opportunities for inter-hemispheric studies. In particular, we study asymmetries in the power of ULF waves. Initial studies with a single pair of conjugate stations at L=1.7 and only for Pc3 waves have found that there is a clear seasonal dependence in the Pc3 power at the conjugate stations. The station at summer solstice always experiences higher Pc3 power. However, a permanent asymmetry between the two hemispheres is also seen with the northern station having predominately higher power throughout the year than the southern station. This pattern was also observed in the conjugate TEC measurements indicating that the two ionospheres are clearly different in the same fashion as the wave power. While the initial study was done for 2 full years, we now extend to cover a longer time period. We are also studying the Pc3 power between other pairs of conjugate stations to determine the latitudinal distribution of the asymmetries. Finally, we extend our inter-hemispheric study to Pc 4-5 ULF waves.

  5. Identification and classification of transient pulses observed in magnetometer array data by time-domain principal component analysis filtering

    Science.gov (United States)

    Kappler, Karl N.; Schneider, Daniel D.; MacLean, Laura S.; Bleier, Thomas E.

    2017-08-01

    A method for identification of pulsations in time series of magnetic field data which are simultaneously present in multiple channels of data at one or more sensor locations is described. Candidate pulsations of interest are first identified in geomagnetic time series by inspection. Time series of these "training events" are represented in matrix form and transpose-multiplied to generate time-domain covariance matrices. The ranked eigenvectors of this matrix are stored as a feature of the pulsation. In the second stage of the algorithm, a sliding window (approximately the width of the training event) is moved across the vector-valued time-series comprising the channels on which the training event was observed. At each window position, the data covariance matrix and associated eigenvectors are calculated. We compare the orientation of the dominant eigenvectors of the training data to those from the windowed data and flag windows where the dominant eigenvectors directions are similar. This was successful in automatically identifying pulses which share polarization and appear to be from the same source process. We apply the method to a case study of continuously sampled (50 Hz) data from six observatories, each equipped with three-component induction coil magnetometers. We examine a 90-day interval of data associated with a cluster of four observatories located within 50 km of Napa, California, together with two remote reference stations-one 100 km to the north of the cluster and the other 350 km south. When the training data contains signals present in the remote reference observatories, we are reliably able to identify and extract global geomagnetic signals such as solar-generated noise. When training data contains pulsations only observed in the cluster of local observatories, we identify several types of non-plane wave signals having similar polarization.

  6. Validity and reliability of smartphone magnetometer-based goniometer evaluation of shoulder abduction--A pilot study.

    Science.gov (United States)

    Johnson, Linda B; Sumner, Sean; Duong, Tina; Yan, Posu; Bajcsy, Ruzena; Abresch, R Ted; de Bie, Evan; Han, Jay J

    2015-12-01

    Goniometers are commonly used by physical therapists to measure range-of-motion (ROM) in the musculoskeletal system. These measurements are used to assist in diagnosis and to help monitor treatment efficacy. With newly emerging technologies, smartphone-based applications are being explored for measuring joint angles and movement. This pilot study investigates the intra- and inter-rater reliability as well as concurrent validity of a newly-developed smartphone magnetometer-based goniometer (MG) application for measuring passive shoulder abduction in both sitting and supine positions, and compare against the traditional universal goniometer (UG). This is a comparative study with repeated measurement design. Three physical therapists utilized both the smartphone MG and a traditional UG to measure various angles of passive shoulder abduction in a healthy subject, whose shoulder was positioned in eight different positions with pre-determined degree of abduction while seated or supine. Each therapist was blinded to the measured angles. Concordance correlation coefficients (CCCs), Bland-Altman plotting methods, and Analysis of Variance (ANOVA) were used for statistical analyses. Both traditional UG and smartphone MG were reliable in repeated measures of standardized joint angle positions (average CCC > 0.997) with similar variability in both measurement tools (standard deviation (SD) ± 4°). Agreement between the UG and MG measurements was greater than 0.99 in all positions. Our results show that the smartphone MG has equivalent reliability compared to the traditional UG when measuring passive shoulder abduction ROM. With concordant measures and comparable reliability to the UG, the newly developed MG application shows potential as a useful tool to assess joint angles. Published by Elsevier Ltd.

  7. Research Award: Employment and Growth

    International Development Research Centre (IDRC) Digital Library (Canada)

    Office 2004 Test Drive User

    IDRC's Employment and Growth program supports policy-oriented research that generates new insights and options for promoting policies that facilitate inclusive growth. This is growth that enhances access of the poor to opportunities and reduces inequalities. Women's economic empowerment and youth employment are ...

  8. Innovation, Industry Evoluation and Employment

    NARCIS (Netherlands)

    D.B. Audretsch (David); A.R. Thurik (Roy)

    1999-01-01

    textabstractThe purpose of this paper is to introduce a series of articles on the links between innovation, the evolution of industry and employment. These relations provide the building blocks of a new industrial policy. The articles are included in Innovation, Industry Evolution and Employment

  9. Employer Demands from Business Graduates

    Science.gov (United States)

    McMurray, Stephen; Dutton, Matthew; McQuaid, Ronald; Richard, Alec

    2016-01-01

    Purpose: The purpose of this paper is to report on research carried out with employers to determine demand for business and management skills in the Scottish workforce. Design/methodology/approach: The research used a questionnaire in which employers were interviewed (either telephone or face to face), completed themselves and returned by e-mail,…

  10. Sensor employing internal reference electrode

    DEFF Research Database (Denmark)

    2013-01-01

    The present invention concerns a novel internal reference electrode as well as a novel sensing electrode for an improved internal reference oxygen sensor and the sensor employing same.......The present invention concerns a novel internal reference electrode as well as a novel sensing electrode for an improved internal reference oxygen sensor and the sensor employing same....

  11. Employability: Review and Research Prospects

    Science.gov (United States)

    Guilbert, Laure; Bernaud, Jean-Luc; Gouvernet, Brice; Rossier, Jérôme

    2016-01-01

    Professional transition, employment, and reemployment are major concerns for nations facing adverse economic situations. The employability construct represents a scientific challenge in order to better understand the relationship between the job seekers' issues and the expectations of the world of work. This paper presents a review of the concept…

  12. The Employable Woman Conference Report.

    Science.gov (United States)

    DeAngelo, Lois; Garcia, Bernice

    The conference proceedings relating to employment status and employment-related problems of women in general, and Montgomery County, Maryland, specifically, are highlighted in this report. The purpose of the conference was to establish a solid base for an on-going dialogue with educators, personnel experts, and affirmative action officers in the…

  13. Opening Doors: Employing the Disabled.

    Science.gov (United States)

    Maurer, Lydia

    The handbook is intended to help employers understand barriers to employment of disabled people. Barriers are examined, including attitudinal, physical (architectural, transportation, site, and equipment), policy and practice barriers (interviewing and recruiting), and communication barriers. Suggestions and guidelines for dealing with the…

  14. The measurement of employment benefits

    International Nuclear Information System (INIS)

    Burtraw, D.

    1994-01-01

    The consideration of employment effects and so-called 'hidden employment benefits' is one of the most confused and contentious issues in benefit-cost analysis and applied welfare economics generally. New investments create new employment opportunities, and often advocates for specific investments cite these employment opportunities as alleged benefits associated with the project. Indeed, from the local perspective, such employment opportunities may appear to be beneficial because they appear to come for free. If there is unemployment in the local area, then new investments create valuable employment opportunities for those in the local community. Even if there is full employment in the local area then new investments create incentives for immigrant from other locations that may have pecuniary benefits locally through increased property values, business revenues, etc. The focus in this study is on net economic benefits from a broad national perspective. From this perspective, many of the alleged employment benefits at the local level are offset by lost benefits at other locales, and do not count as benefits according to economic theory. This paper outlines a methodology for testing this rebuttable presumption with empirical data pertaining to labor markets that would be affected by a specific new investment. The theoretical question that is relevant is whether the social opportunity cost of new employment is less than the market wage. This would be the case, for example, if one expects unemployment or underemployment to persist in a specific region of the economy or occupational category affected by the new investment. In this case, new employment opportunities produce a net increase in social wealth rather than just a transfer of income

  15. Magnetic Zn (II) ion-imprinted polymer prepared by the surface imprinting technique and its adsorption properties.

    Science.gov (United States)

    Zhang, Hui-xin; Dou, Qian; Jin, Xiu-hong; Zhang, Jie; Yang, Ting-ru; Han, Xu; Wang, Dong-dong

    2015-01-01

    A novel magnetic Zn (II) ion-imprinted polymer was prepared by the surface ion-imprinted technique by using magnetic Fe3O4@SiO2 microspheres as supporter, methacrylic acid and salicylaldoxime as monomers, ethylene glycol dimethacrylate as the crosslinker. The products were characterized by Fourier transform infrared, X-ray photoelectron spectrometer, vibrating sample magnetometer and scanning electron microscope. The adsorption experiments showed that the imprinted polymer was employed successfully in comparison with non-imprinted polymer. When the temperature was in a range of 291-297 K, the maximum adsorption was about 52.69 mg g(-1) with an optimal pH 6.0 for an equilibrium time of 40 min. The imprinted polymer possessed high selectivity and specific recognition towards Zn (II). The Langmuir adsorption model was more favourable than the Freundlich or the Temkin adsorption model. Thermodynamic experiment showed that the adsorption was a spontaneous and endothermic process for Zn (II). The mechanism for Zn (II) adsorption on the imprinted polymer was investigated.

  16. EMPLOYMENT HISTORY AND OFF-FARM EMPLOYMENT OF FARM OPERATORS

    OpenAIRE

    Stallmann, Judith I.; Nelson, James H.

    1995-01-01

    Employment history affects subsequent choices. Based on their original job choice, operators are divided into farmers and workers. Equations are estimated to determine their probabilities of working off-the-farm. Education increased the probability that workers work off-the-farm, whereas vocational training increases farmers' probability. The probability of working off-the-farm decreases as unearned income increases, and its impact on workers is larger than on farmers. An employed spouse incr...

  17. Additional employer and employee obligations of the contract of employment

    OpenAIRE

    Jankauskaitė, Vaida

    2009-01-01

    Economic growth since 2001 till 2008 start leaded to higher incomes for both employers and employees, many new jobs were created. The unemployment rate in Lithuania was particularly low, moreover, according to official statistics, nearly half a million people emigrated from Lithuania. Labor market challenges and economic patterns determined the principles of the labor law and the content of the norms, public social and political conditions. Employers, through businesses, noticed that it has b...

  18. A Sensitive, Multifunctional Spinner Magnetometer Using Magneto-impedance Sensor: a Rapid and Convenient Tool for the Quantification of Inhomogeneity of Magnetization

    Science.gov (United States)

    Kodama, K.

    2016-12-01

    A new type of spinner magnetometer with wide dynamic range from 10-7 mAm2 to 10-1 mAm2 and the resolution of 10-8 mAm2 was developed. The high sensitivity was achieved by using magneto-impedance (MI) sensor, a compact, high-performance magnetic sensor used in industrial fields. The slow spinning speed (5 Hz) and the unique mechanism enabling the adjustment of the sample-sensor distance allow measurements of fragile samples in any shape and size. A differential arrangement connecting a pair of the MI sensors in opposite serial reduces external noise and temperature drift. The differential sensor output is transferred to an amplification circuit associated with a programmable low-pass filter. The signal with reference to the spinning frequency is detected with a digital lock-in amplifier. The spinner magnetometer has two selectable measurement modes, the fundamental-mode (F-mode) and the harmonic-mode (H-mode). Measurements in the F-mode detect signals oscillating at the fundamental frequency (5 Hz) as conventional spinner magnetometers do. In the H-mode, additionally, the second (10 Hz) and the third (15 Hz) harmonic components can be measured. Tests in the H-mode were performed using a small coil and changing its position to simulate an offset-dipole. The results demonstrate that the dipole moment of the fundamental component is systematically biased by both quadrupole and octupole components arising in practice from inhomogeneity of magnetization or irregularity of sample shape. This study proposes, combined with theoretical and numerical analyses, quantification of such non-dipole effects and associated errors in the determination of dipole moment of a sample, as well as their correction that may be necessary, for example, when measuring irregular-shaped samples in the proximity of the sensor.

  19. Employment Discrimination against LGBT Utahns

    OpenAIRE

    Rosky, Clifford; Mallory, Christy; Smith, Jenni; Badgett, M.V. Lee

    2011-01-01

    This study analyzes data from a 2010 survey on the employment experiences of 939 LGBT people living in Utah.  The study found that 44% of LGB people and 66% of transgender people in Utah have experienced employment discrimination.  The data showed that employment discrimination based on sexual orientation and gender identity currently occurs in Utah, with close to 30% of LGB respondents and 45% of transgender respondents reporting that they experienced some form of workplace harassment on a w...

  20. Employability of Nursing Care Graduates

    Directory of Open Access Journals (Sweden)

    Donik Barbara

    2015-12-01

    Full Text Available Starting points: In Slovenia, the higher education institution for nursing started exploring employability opportunities in nursing care in connection with the achievement of competencies from students’ and employers’ point of view. This article highlights the importance of monitoring nursing graduates’ employability. Its aim is to examine the employability of nursing care graduates based on the self-evaluation of competences obtained during the last study year and to establish a link between the self-evaluation of competences and students’ academic performance.

  1. Magnetic field fluctuations measurement onboard ESA/JUICE mission by search-coil magnetometer: SCM instrument as a part of RPWI consortium

    Science.gov (United States)

    Retinò, A.; Chust, T.; Mansour, M.; Canu, P.; Sahraoui, F.; Le Contel, O.; Alison, D.; Sou, G.; Varizat, L.; Techer, J.-D.; Jeandet, A.; Geyskens, N.; Chariet, M.; Cecconi, B.; Bergman, J.; Wahlund, J.-E.; Santolik, O.; Soucek, J.; Dougherty, M.

    2017-09-01

    The JUpiter ICy moons Explorer (JUICE) mission is planned for launch in 2022 with arrival at Jupiter in 2029 and will spend at least three years making detailed observations of Jupiter's system. The Radio and Plasma Wave Investigation (RPWI) consortium will carry the most advanced set of electric and magnetic fields sensors ever flown therein, which will allow to characterize the plasma wave environment and the radio emission of Jupiter and its icy moons in great detail. The Search Coil Magnetometer (SCM) will provide high-quality measurements of the magnetic field fluctuations' vector for RPWI. Here we present the technical features of the SCM instrument and we discuss its scientific objectives.

  2. 45 CFR 400.76 - Criteria for exemption from registration for employment services, participation in employability...

    Science.gov (United States)

    2010-10-01

    ... employment services, participation in employability service programs, and acceptance of appropriate offers of... RESETTLEMENT PROGRAM Requirements for Employability Services and Employment General Requirements § 400.76 Criteria for exemption from registration for employment services, participation in employability service...

  3. Maternal Employment and Childhood Obesity

    DEFF Research Database (Denmark)

    Gwozdz, Wencke; Sousa-Poza, Alfonso; Reisch, Lucia

    The substantial increase in female employment rates in Europe over the past two decades has often been linked in political and public rhetoric to negative effects on child development, including obesity. We analyse this association between maternal employment and childhood obesity using rich...... objective reports of various anthropometric and other measures of fatness from the IDEFICS study of children aged 2-9 in 16 regions of eight European countries. Based on such data as accelerometer measures and information from nutritional diaries, we also investigate the effects of maternal employment...... on obesity's main drivers: calorie intake and physical activity. Our analysis provides little evidence for any association between maternal employment and childhood obesity, diet or physical activity....

  4. Maternal Employment and Childhood Obesity

    DEFF Research Database (Denmark)

    Gwozdz, Wencke; Sousa-Poza, Alfonso; Reisch, Lucia

    2013-01-01

    The substantial increase in female employment rates in Europe over the past two decades has often been linked in political and public rhetoric to negative effects on child development, including obesity. We analyse this association between maternal employment and childhood obesity using rich...... objective reports of various anthropometric and other measures of fatness from the IDEFICS study of children aged 2-9 in 16 regions of eight European countries. Based on such data as accelerometer measures and information from nutritional diaries, we also investigate the effects of maternal employment...... on obesity's main drivers: calorie intake and physical activity. Our analysis provides little evidence for any association between maternal employment and childhood obesity, diet or physical activity....

  5. Analysing race inequality in employment

    OpenAIRE

    Griffiths, Elisabeth

    2016-01-01

    Elisabeth Griffiths, principal lecturer at Northumbria Law School at Northumbria University, explores employment issues in the recent review by the Equality and Human Rights Commission (EHRC) of prejudice and unlawful behaviour because of race.

  6. Employment growth and regional development

    DEFF Research Database (Denmark)

    Eriksson, Rikard; Hansen, Høgni Kalsø; Winther, Lars

    2017-01-01

    This paper explores the potential drivers behind uneven regional development in the context of employment growth in Denmark and Sweden. In particular, we are interested in the roles of urbanization, industrial change and the rise of the new economy as manifested in the growth of the two economies...... in 2002–2007. The aim of this paper is, therefore, to analyse the impact of a number of key industrial sectors on regional employment growth in the two countries. The empirical analysis is based on longitudinal matched employer–employee data retrieved from official registers in each economy from 2002...... to 2007, a period of strong national growth following the crisis of early 2000. Our findings indicate that the two economies follow a similar pattern in addressing total employment growth; but looking at changes in employment levels across the national borders of these two relatively similar open...

  7. New Office Technology and Employment.

    Science.gov (United States)

    Cockroft, David

    1980-01-01

    Shows that there are potential problems associated with technological change which demand both serious analytical treatment and the development of sophisticated industrial and social policies. Discusses the office sector, office technology, employment, and trade unions. (CT)

  8. Consultation Services for the Employer

    National Research Council Canada - National Science Library

    1997-01-01

    The Occupational Safety and Health Administration (OSHA) is sensitive to the difficulties faced by employers who are genuinely concerned with their employees' safety and health and who wish to comply with OSHA regulations...

  9. Employer-sponsored pension plans

    Directory of Open Access Journals (Sweden)

    Rakonjac-Antić Tatjana N.

    2004-01-01

    Full Text Available Apart from pension plans within social insurance, in developed pension systems there are also available to individuals schemes which may to a large extent ensure a significant part of their total pension. Among them are the following: employer-sponsored pension plans or individual pension plans. The most widely used employer-sponsored pension plan in the USA is 401(k, in which both the employer and the employee contribute to the financing of the pension. These contributions as well as the return to their investment have a preferential tax treatment, i.e. do not enter a tax base. The funds are taxed only when drawn from the account in the form of a pension. This paper aims to present the functioning of 401(k pension plan as the most widely used employer sponsored pension plan in the USA, which is likely, in a modified form, to have an important place within our future reformed pension insurance system.

  10. Employer Branding: An Islamic Perspective

    Directory of Open Access Journals (Sweden)

    Norasyikin binti Shaikh Ibrahim

    2017-05-01

    Full Text Available This paper discusses employer branding from an Islamic perspective. Islam is away of life and so do the employer and employee relationship, which strengthensemployer branding in an organization. The definition, importance and processrelated to employer branding are discussed in the context of human resource management, such as job satisfaction and work environment. In addition to that, related human resource management practices such as recruitment andselection were discussed in an Islamic context. Related concepts such as employeevalue proposition (EVP, ethics and Islamic values were discussed with referencefrom Al-Quran and Hadith. The paper concludes with a few suggestions andrecommendations on instilling Islamic values for effective employer branding.

  11. Employment protection legislation in Croatia

    Directory of Open Access Journals (Sweden)

    Marina Kunovac

    2014-06-01

    Full Text Available According to business climate and competitiveness indicators published by international organisations, Croatia is a country with a rigid labour market and a high level of the legal protection of employees. Given that an Act on Amendments to the Labour Act (OG 73/13 entered into force in Croatia in June 2013, this paper examines changes in employment protection legislation in Croatia and Central and Eastern European (CEE countries, as well as in Croatia's main trading partners during the period between 2008 and 2013. A cross-country comparison shows a strong downward trend in legal employment protection in most CEE countries during the observed period, primarily as concerns individual dismissal in the cases of regular employment contracts, while in the case of temporary employment the protection strengthened slightly. On the other hand, despite the adoption of amendments to the Labour Act (LA, Croatian labour legislation governing employment protection for regular employment contracts remains relatively inflexible compared to that in other countries.

  12. Employer attractiveness from a generational perspective: Implications for employer branding

    Directory of Open Access Journals (Sweden)

    Germano Glufke Reis

    2016-03-01

    Full Text Available ABSTRACT This study aimed to identify the employer attractiveness factors prioritized by different generations: Baby Boomers, Generation X, and Generation Y. The survey was conducted with a sample of 937 professionals, working in various areas and companies, most of them were managers and had a high education level. The Employer Attractiveness Scale proposed by Berthon et al. (2005 was adopted and the results indicate that, when choosing a company, the generations under study have specific features regarding the attractiveness attributes they prioritize. It was also observed that Generation Y discriminates and ranks such attributes more clearly than the others. Possible implications for employer branding and research limitations are discussed at the end of the article.

  13. Employee to employer communication skills: balancing cancer treatment and employment.

    Science.gov (United States)

    Brown, Richard F; Owens, Myra; Bradley, Cathy

    2013-02-01

    Cancer patients face difficulties in accessing legally mandated benefits and accommodations when they return to the workplace. Poor employer-employee communication inflates these difficulties. Although proven methods to facilitate physician-patient communication exist, these have not been applied to the workplace. Thus, we aimed to assess the feasibility and utility of applying these methods to educate patients about their workplace rights and provide them with communication skills training to aid their conversations with their employers. A DVD was produced to educate patients and facilitate workplace communication. Participants consisted of 28 solid tumor cancer patients (14 women and 14 men) who completed primary cancer treatment in the past 12 months and were employed at the time of diagnosis. Participants watched a communication skills training DVD and completed a telephone interview. The interview elicited information about workplace experiences and evaluation of the DVD training program. The physician-patient communication skills training model utilized was successfully translated to the employer-employee setting. All but one participant found the DVD useful and easy to understand and indicated a high degree of confidence in using the communication skills to help them ask for workplace accommodations. All participants agreed that it would help newly diagnosed patients in discussions with their employers. Our data provides promising preliminary evidence that patient communication skills training can be applied to the workplace setting and is a welcomed aid to newly diagnosed cancer patients in their discussions with employers regarding the impact of treatment on their work performance and needs for accommodations. Copyright © 2011 John Wiley & Sons, Ltd.

  14. Monitoring of the mass density profile along the 0° geomagnetic longitude during magnetic storms with the use of ground magnetometers.

    Science.gov (United States)

    Romanova, N.; Stepanova, M. V.; Kozyreva, O. V.; Pilipenko, V.; Zesta, E.

    2015-12-01

    Ground magnetometers offer a very cheap and robust means of globally monitoring the magnetospheric mass density, by determining the ULF field line resonant frequency. ULF waves are almost always present in near-Earth environment and are generated by the solar wind interaction with the terrestrial magnetosphere. These waves from the magnetopause propagate through the magnetosphere. When they encounter a field line that resonates at the same frequency, coupling to the Alfven field line oscillations occurs and the resonance can be detected on the ground at that particular latitude. There are different methods for determining resonant frequencies from ground ULF waves. the density profiles along the 0° geomagnetic longitude were obtained using both the gradient and the amplitude-phase methods for the analysis of the magnetic field data from the magnetometer arrays: SAMBA (South American Meridional B-field Array), MAGDAS and American Antarctic bases (Palmer, WAIS-D). We compared the density profiles during quiet magnetic conditions and during strong magnetic storms (recovery phase). It is shown that in the recovery phase of strong magnetic storms (Dst <-150 nT) profile of the equatorial mass density varies greatly in comparison with the density distribution in quiet days.

  15. A dead-zone free ⁴He atomic magnetometer with intensity-modulated linearly polarized light and a liquid crystal polarization rotator.

    Science.gov (United States)

    Wu, T; Peng, X; Lin, Z; Guo, H

    2015-10-01

    We demonstrate an all-optical (4)He atomic magnetometer experimental scheme based on an original Bell-Bloom configuration. A single intensity-modulated linearly polarized laser beam is used both for generating spin polarization within a single (4)He vapor and probing the spin precessing under a static magnetic field. The transmitted light signal from the vapor is then phase-sensitively detected at the modulation frequency and its harmonics, which lead to the atomic magnetic resonance signals. Based on this structure, a liquid crystal is added in our magnetometer system and constitutes a polarization rotator. By controlling the voltage applied on the liquid crystal, the light linear polarization vector can be kept perpendicular with the ambient magnetic field direction, which in turn provides the maximum resonance signal amplitude. Moreover, the system exhibits a magnetic-field noise floor of about 2pT/√Hz, which is not degraded due to the presence of the liquid crystal and varying magnetic field direction. The experiment results prove that our method can eliminate the dead-zone effect, improve the system spatial isotropy, and thus be suitable in mobile applications.

  16. Low-noise YBa2Cu3O7-x single layer dc superconducting quantum interference device (SQUID) magnetometer based on bicrystal junctions with 30° misorientation angle

    Science.gov (United States)

    Beyer, J.; Drung, D.; Ludwig, F.; Minotani, T.; Enpuku, K.

    1998-01-01

    We have fabricated and characterized a low-noise direct-coupled magnetometer based on a 100 pH YBa2Cu3O7-x dc superconducting quantum interference device (SQUID) on a 10 mm×10 mm SrTiO3 bicrystal substrate with 30° misorientation angle. The thin films were deposited by hollow cathode discharge sputtering and patterned using conventional photolithography and Ar ion beam etching. The SQUID magnetometer was operated using direct-coupled flux-locked-loop electronics with bias reversal. The sensor had a usable voltage swing of 39 μV and a white magnetic field noise of 32 fTHz-1/2 with a 1/f corner at 2 Hz, including electronics and environmental noise. The voltage versus flux (V-Φ) characteristic showed a pronounced distortion on the negative slope. Numerical simulations were performed to explain the distorted V-Φ characteristic. Measurements of magnetocardiograms demonstrate the suitability of this sensor for biomagnetic applications.

  17. Employability and Employment Outcomes of No-Fee Preservice Students

    Science.gov (United States)

    Jin, Yule; Li, Ling; Ding, Shujing; Li, Zhichao

    2013-01-01

    This study used interviews and questionnaires to survey 770 no-fee preservice students. Its findings were as follows: (1) Their employability encompasses five dimensions: teaching skills, ability to learn specialized knowledge, ability to grasp elementary and secondary teaching materials and methods, communication skills, and ability to apply for…

  18. Graduates' Employability: What Do Graduates and Employers Think?

    Science.gov (United States)

    Matsouka, Kyriaki; Mihail, Dimitrios M.

    2016-01-01

    The purpose of this article is to investigate the views of university graduates and human resource managers (HRMs) on graduates' employability in terms of the soft skills required by the labour market. Soft skills (personal attributes that enhance an individual's interactions, job performance and career prospects) are necessary in the labour…

  19. International employment policies: employment and stabilisation in Mexico.

    OpenAIRE

    Mertens L

    1986-01-01

    ILO pub-WEP pub. Working paper on the impact of stabilization and adjustment policies (economic policy) on employment, Mexico, prospects for the 1980s - examines the transition from import substitution industrialization to an economic model based on export oriented industry, structural changes and subsequent financial collapse (financial policy), economic growth performance, 1978-1981, the external debt crisis, etc. Bibliography, statistical tables.

  20. Making sense of employer collectivism

    DEFF Research Database (Denmark)

    Ibsen, Christian Lyhne

    2016-01-01

    This conceptual article argues that preferences of employers for collective action cannot be reduced to rational actors making decisions based on market structures or institutional logics. Both markets and institutions are inherently ambiguous and employers therefore have to settle for plausible...... – rather than accurate – rational strategies among many alternatives through so-called sensemaking. Sensemaking refers to the process by which employers continuously make sense of their competitive environment by building causal stories of competitive advantages. The article therefore tries to provide...... that allude to the ambiguous role of markets and institutions but do not study how actors deal with this ambiguity. The sensemaking concept is illustrated with an analysis of wage bargaining in Denmark during the recent recession when Danish labour cost competitiveness was in a deplorable state. However...

  1. Global Employer and Business Associations

    DEFF Research Database (Denmark)

    Ronit, Karsten

    2016-01-01

    Global employer and business associations at the peak level are neglected in research, but this paper argues that it is possible to develop collective action and represent interests in many policy fields through these encompassing entities, and they add to other forms of global business...... coordination. This study analyses all the global peak associations (International Chamber of Commerce, International Organisation of Employers, World Chambers Federation, Business and Industry Advisory Committee to the OECD, B20 Coalition, World Economic Forum and World Business Council for Sustainable...... implications for our understanding of global politics where new approaches are needed to analyse the institutionalisation of business interests....

  2. Employment Growth and International Trade

    DEFF Research Database (Denmark)

    Ibsen, Rikke; Warzynski, Frederic; Westergård-Nielsen, Niels Chr.

    In this paper, we use a detailed dataset containing information about all international trade transactions of the population of Danish ?rms over more than a decade to analyze the relationship between export and import decisions and employment growth. We further distinguish between imports of ?nal...... goods and imports of intermedi­ate products. We ?nd that both imports and exports decisions are positively related to employment growth. Interestingly, both ?nished goods and intermediate goods imports have a positive link. We also control for the re-exporting process, i.e. ?rms importing ?nal goods...

  3. Technological Innovation and Employment Reallocation

    OpenAIRE

    Greenan, Nathalie; Guellec, Dominique

    2000-01-01

    ; International audience; The paper describes the dynamics of employment at a firm and sector level in the French industry and examines how far technological innovation can give account of it. We use a firm sample of 15,186 firms, over the 1986-1990 period. The two facts we want to explain at a firm level and a sector level are the net change in employment and the micro turmoil (transfers between competing firms). Innovating firms and sectors create jobs more than others over medium run (5 ye...

  4. Higher Education, Employability and Competitiveness

    Science.gov (United States)

    Pavlin, Samo; Svetlicic, Marjan

    2012-01-01

    This paper studies the relationship between competitiveness and higher education systems in Europe. It explores whether more competitive countries have developed more labour-market-oriented systems of higher education (HE) that thereby give their graduates greater short term employability potential. Based on and a large-scale survey among 45.000…

  5. Transnational Education and Employability Development

    Science.gov (United States)

    Mellors-Bourne, Robin; Jones, Elspeth; Woodfield, Steve

    2015-01-01

    Internationalisation and employability development are important themes for UK higher education (HE) and the Higher Education Academy (HEA). One aspect of many UK HE institutions' internationalisation strategies has been to increase the number and range of UK programmes delivered "offshore" as transnational education (TNE)--through…

  6. Youth Employment and Job Creation.

    Science.gov (United States)

    Connors, Tad

    A policy that addresses youth unemployment with monetary expansion for similar fiscal policies is criticized as compounding the problem, and alternative solutions are offered. Accordingly, a brief look at youth labor market characteristics, pertinent labor market theory, and the present industrial distribution of employed youth is offered. A…

  7. EMPLOYABILITY van UM-afgestudeerden

    NARCIS (Netherlands)

    van Eldert, Peter; Künn, Annemarie; Mommers, Ardi

    2017-01-01

    De voor u liggende studie is een weerslag van het project ‘Employability onder UM afgestudeerden’. Het rapport geeft eerst een samenvatting van de uitgevoerde literatuurstudie op het gebied van ‘employability’ in het hoger onderwijs. Vervolgens wordt de ‘employability’ van UM afgestudeerden vijf

  8. Patient advocacy versus employer protection.

    Science.gov (United States)

    Deubner, David; Sturm, Richard E

    2002-01-01

    In a departure from the usual Occupational Medicine: State of the Art Reviews article, this piece comprises responses from two occupational physicians to the question of how balance is achieved between employer and patient interests in occupational medicine. The authors discuss the ethical dilemmas that may arise in such relationships, negotiation of confrontations, physician responsibilities, and conflict resolution.

  9. Employment status and working conditions

    NARCIS (Netherlands)

    Goudswaard, A.; Andries, F.

    2002-01-01

    In the 1990s an increasing number of employees were engaged in non-permanent contract work in the European Union. This can, to a large extent, be explained by an active labour market policy where job creation was the focus, and this type of employment provided a way of meeting the increased demand

  10. Employment and Unemployment in Lagos

    NARCIS (Netherlands)

    O. Fapohunda (Olanrewaju)

    1977-01-01

    textabstractWage-earning employment was non-existent in Nigeria before the advent of the white man and the British administration. The average Nigerian engaged in subsistence agriculture or some cottage industry like weaving, pottery or carving. The first wage earners in Nigeria were probably the

  11. Employers' Perspectives of Online Education

    Science.gov (United States)

    Linardopoulos, Nikolaos

    2012-01-01

    Purpose: The purpose of this paper is to describe the strengths and weaknesses of seven representative studies pertaining to the employers' perceptions of online education. Design/methodology/approach: The paper retrieved and analysed representative studies on the subject from two scholarly databases and Google. Findings: The results indicate that…

  12. Job satisfaction and contingent employment

    NARCIS (Netherlands)

    de Graaf-Zijl, M.

    2012-01-01

    This paper analyses job satisfaction as an aggregate of satisfaction with several job aspects, with special focus on the influence of contingent-employment contracts. Fixed-effect analysis is applied on a longitudinal sample of Dutch employees in four work arrangements: regular, fixed-term, on-call

  13. Teaching Soft Skills Employers Need

    Science.gov (United States)

    Ellis, Maureen; Kisling, Eric; Hackworth, Robbie G.

    2014-01-01

    This study identifies the soft skills community colleges teach in an office technology course and determines whether the skills taught are congruent with the soft skills employers require in today's entry-level office work. A qualitative content analysis of a community college office technology soft skills course was performed using 23 soft skills…

  14. Employment effects of biofuels development

    International Nuclear Information System (INIS)

    Danielsson, B.O.; Hektor, B.

    1992-01-01

    Effects on employment - national and regional - from an expanding market for biofuels in Sweden are estimated in this article. The fuels considered are: Peat, straw, energy crops, silviculture, forestry waste, wood waste, by-products from paper/wood industry and processed fuels from these sources. (22 refs., tabs.)

  15. Employment and Urban Native Canadians.

    Science.gov (United States)

    Abrahams-Maclachlan, Caryl; And Others

    1982-01-01

    Measured differences in employment issues between native Canadian Indians and a nonnative comparison group in Toronto. Given similar circumstances, found Native Canadians less formally educated and skill trained than nonnatives of comparable age, sex, and education. Respondents under 25 and over 50 earned substantially less. (Author)

  16. Sex Discrimination in Employment Practices.

    Science.gov (United States)

    California Univ., Los Angeles. Univ. Extension.

    The conference on sex discrimination in employment practices was held at the University of California at Los Angeles in cooperation with the Women's Bureau of the Department of Labor. Speeches included: (1) "New Legislation--New Action" by Rosalind K. Loring and William Foster, (2) "Compliance Policies and Procedures for Business and Industry" by…

  17. Income, employment and suicidal behavior.

    Science.gov (United States)

    Kalist, David E; Molinari, Noelle-Angelique M; Siahaan, Freddy

    2007-12-01

    Little is known about the labor market outcomes of people who have attempted suicide or thought about suicide. We used micro-level data from the first wave of the National Epidemiologic Survey on Alcohol and Related Conditions 2001-2002 to examine the effects of suicidal behavior on income and employment. The data provide a representative sample of the U.S. population, with its primary purpose to provide information on alcohol use disorders for the civilian non-institutionalized population aged 18 and over. The data include employment, income, and other socioeconomic and demographic information on respondents. Since the survey included 43,093 people, the data include a large number of respondents who attempted suicide or thought about committing suicide. We estimated earnings regressions and logit and ordered logit employment regressions. We used methods of IV estimation as well as two stage linear probability models to address potential endogeneity of suicidal behavior while estimating regressions separately by sex, since there are significant differences in suicide rates, suicide attempts, and suicidal ideation between men and women. We find that suicide attempts and suicidal ideation are negatively related to personal income and the probability of employment. The effects differ by sex. Men and women who attempted suicide had mean earnings lower by 16 and 13 percent, respectively. This amount reflects the combined effect of suicidal behavior and mental illness. With instrumental variable regression, the magnitude of the effects becomes larger-for example, as much as 50 percent decrease in the income of males who attempted suicide. Thoughts of suicide negatively affect income but to a smaller extent. Logit and ordered logit regressions indicate that attempted suicide reduces the probability of fulltime employment by over 20 percentage points for men and approximately 17 percentage points for women. People who engaged in suicidal behavior reported significantly

  18. 45 CFR 400.75 - Registration for employment services, participation in employability service programs and...

    Science.gov (United States)

    2010-10-01

    ..., participation in employability service programs and targeted assistance programs, going to job interviews, and... HEALTH AND HUMAN SERVICES REFUGEE RESETTLEMENT PROGRAM Requirements for Employability Services and Employment General Requirements § 400.75 Registration for employment services, participation in employability...

  19. Employment, Social Networks and Undocumented Migrants: The Employer Perspective

    Science.gov (United States)

    Bloch, Alice; McKay, Sonia

    2015-01-01

    This article draws on data from qualitative interviews with ethnic enclave and ethnic economy business entrepreneurs from Chinese, Bangladeshi and Turkish-speaking communities in London. Routes into business and worker recruitment practices are explored, demonstrating the centrality of social capital in the form of family and other social networks within these processes. The article investigates what employers consider the desirable characteristics of workers: trust, kinship, gender, social networks, language compatibility and the needs of the business intersect with racialised notions of workers’ strengths and characteristics. Finally, we consider changing practices in relation to the employment of undocumented migrants, in the context of an increasingly punitive legislative regime. The complex and variable impact of policy alongside the ways in which other obligations and positions outweigh the fear and risks of sanctions associated with non-compliance is revealed. PMID:25866421

  20. Employment, Social Networks and Undocumented Migrants: The Employer Perspective.

    Science.gov (United States)

    Bloch, Alice; McKay, Sonia

    2015-02-01

    This article draws on data from qualitative interviews with ethnic enclave and ethnic economy business entrepreneurs from Chinese, Bangladeshi and Turkish-speaking communities in London. Routes into business and worker recruitment practices are explored, demonstrating the centrality of social capital in the form of family and other social networks within these processes. The article investigates what employers consider the desirable characteristics of workers: trust, kinship, gender, social networks, language compatibility and the needs of the business intersect with racialised notions of workers' strengths and characteristics. Finally, we consider changing practices in relation to the employment of undocumented migrants, in the context of an increasingly punitive legislative regime. The complex and variable impact of policy alongside the ways in which other obligations and positions outweigh the fear and risks of sanctions associated with non-compliance is revealed.

  1. EEO Review : youth employment measures, 2010 - Malta

    OpenAIRE

    Debono, Manwel

    2010-01-01

    This report explores youth employment measures in Malta. It outlines the trends in youth employment. Then it examines measures taken to promote youth employment, focusing on school education and training policies, labour market and employment-related policies, and access to benefits. Finally, the report focuses on the roles of labour market actors in the promotion of youth employment.

  2. Artificial Intelligence, Employment, and Income

    OpenAIRE

    Nilsson, Nils J.

    1984-01-01

    Artificial intelligence (AI) will have profound societal effects. It promises potential benefits (and may also pose risks) in education, defense, business, law and science. In this article we explore how AI is likely to affect employment and the distribution of income. We argue that AI will indeed reduce drastically the need of human toil. We also note that some people fear the automation of work by machines and the resulting of unemployment. Yet, since the majority of us probably would rathe...

  3. Ghana Youth Employment Program Inventory

    OpenAIRE

    Ulzen-Appiah, Ato; Avura, Francis Babongte

    2016-01-01

    This youth employment inventory has been compiled to improve the evidence base for making decisions about how to address the problem of youth unemployment or youth who are not in education and not participating in the labor market in Ghana. Policy makers who are considering measures to help young people make the transition into the labor market and obtain decent work are hampered by a lack ...

  4. Population and Employment in China

    OpenAIRE

    Keyfitz, N.

    1982-01-01

    China's effectiveness in population control can be credited to the direct line of command through party and administrative cadres that extends from the leadership in Beijing down to the production team in a distant rural commune. The reason that the administrative machine has devoted so much attention to population control is twofold: the perceived limits of the natural environment, as indicated by slowness of growth of food supplies, and the difficulty of arranging productive employment for ...

  5. Achieving and sustaining full employment.

    Science.gov (United States)

    Rosen, S M

    1995-01-01

    Human rights and public health considerations provide strong support for policies that maximize employment. Ample historical and conceptual evidence supports the feasibility of full employment policies. New factors affecting the labor force, the rate of technological change, and the globalization of economic activity require appropriate policies--international as well as national--but do not invalidate the ability of modern states to apply the measures needed. Among these the most important include: (I) systematic reduction in working time with no loss of income, (2) active labor market policies, (3) use of fiscal and monetary measures to sustain the needed level of aggregate demand, (4) restoration of equal bargaining power between labor and capital, (5) social investment in neglected and outmoded infrastructure, (6) accountability of corporations for decisions to shift or reduce capital investment, (7) major reductions in military spending, to be replaced by socially needed and economically productive expenditures, (8) direct public sector job creation, (9) reform of monetary policy to restore emphasis on minimizing unemployment and promoting full employment. None are without precedent in modern economies. The obstacles are ideological and political. To overcome them will require intellectual clarity and effective advocacy.

  6. 38 CFR 21.58 - Redetermination of employment handicap and serious employment handicap.

    Science.gov (United States)

    2010-07-01

    ... employment handicap and serious employment handicap. 21.58 Section 21.58 Pensions, Bonuses, and Veterans... of employment handicap and serious employment handicap. (a) Prior to induction into a program. A determination as to employment handicap, serious employment handicap, or eligibility for a program of employment...

  7. The mechanism of mid-latitude Pi2 waves in the upper ionosphere as revealed by combined Doppler and magnetometer observations

    Directory of Open Access Journals (Sweden)

    V. A. Pilipenko

    2013-04-01

    Full Text Available The interpretation of simultaneous ionospheric Doppler sounding and ground magnetometer observations of low-latitude Pi2 waves is revised. We compare the theoretical estimates of the ionospheric Doppler velocity for the same amplitude of the ground magnetic disturbances produced by a large-scale compressional mode and an Alfvén mode. The plasma vertical displacement caused by the wave electric field is shown to be the dominating effect. Taking into account the correction of the previous paper, the observations of low-latitude Pi2 in the F layer ionosphere by Doppler sounding and SuperDARN (Super Dual Auroral Radar Network radars give consistent results. We suggest that the Doppler response to Pi2 waves is produced by the Alfvén wave component, but not the fast-mode component, whereas the ground magnetic signal is composed from both Alfvén and fast magnetosonic modes.

  8. Influence of the dynamic Stark effect on long-term frequency stability of a self-oscillating magnetometer with laser-pumped alkali atoms

    Science.gov (United States)

    Baranov, A. A.; Ermak, S. V.; Kulachenkov, N. K.; Petrenko, M. V.; Sagitov, E. A.; Semenov, V. V.

    2017-11-01

    This paper presents the results of investigation Stark shift effect influence on the long-term stability of a dual scheme of quantum magnetometers. Such scheme allows suppressing Stark shift components when a certain pumping light polarization is applied. As a result, long-term stability of a quantum sensor increases. However, when low-frequency (LF) and microwave fields are attached to a single vapor cell a coherence circulation in hyperfine structure of alkali atoms takes place. Physical origin of this effect is associated with the so called “dressed” atom theory, when atom is “dressed” by LF field. It yields in multiphoton absorption and resonance frequency shift. First estimates for this shift based on density matrix evolution formalism are provided in the paper.

  9. Report on gravity measurements and replacement of an unmanned magnetometer in the Sor Rondane Mountains, Eastern Dronning Maud Land, 2013 (JARE-55

    Directory of Open Access Journals (Sweden)

    Yusuke Suganuma

    2014-11-01

    Full Text Available Gravity measurements, replacement of the unmanned magnetometer, and a reconnaissance flight to the Belgica Mountains were carried out in the Sor Rondane Mountains as a part of the 55 th Japanese Antarctic Research Expedition (JARE-55. The field party comprised two geodesists, one geomorphologists, and one magnetospheric scientist. The Belgian Antarctic Research Expedition (BELARE and International Polar Foundation (IPF supported this field expedition. Dronning Maud Land Air Network (DROMLAN provided airborne access from Cape Town, South Africa to the Sor Rondane Mountains via Novolazarevskaya Airbase. The survey areas of this field expedition are the central parts of the Sor Rondane Mountains and the Belgica Mountains. This report summarizes the field expedition in terms of operations, logistics, and weather observations.

  10. Employer`s contributions to the training of professional statisticians

    Energy Technology Data Exchange (ETDEWEB)

    Rustagi, J.S. [Ohio State Univ., Columbus, OH (United States). Statistics Dept.; Wright, T. [Oak Ridge National Lab., TN (United States). Mathematical Sciences Section]|[Bureau of the Census, Washington, DC (United States)

    1995-07-01

    Statistical science provides important techniques for decision making in a large variety of fields of human endeavor mainly through statistical practice. According to Deming (1965), ``Statistical practice is mostly a collaborative venture between (professional) statisticians and experts in subject-matter (area).`` The professional statistician must be properly trained in areas of statistical science most suited to the discipline in which the applications are made. Due to a large variety of applications. The education of a professional statistician by universities can only be very general. Higher education provides the theoretical basis of statistical science whereas the specific expertise needed by the professional statistician is given by the application areas. In this paper, the authors review the approach of academic programs which are geared towards applications and discuss some of the innovative strategies for preparing statisticians as consultants in industry and business. A survey (census) of statisticians at the national laboratories of the US Department of Energy was made to assess their training by universities and to get a broad view of additional training which has brought them to their present professional status. A particular interest is the extent to which employers have contributed to the training of statisticians. A few recommendations are made which may serve to improve the future training of statisticians for applied collaborative work by universities and employers.

  11. Youth employment problems in Latvia

    OpenAIRE

    Mičule, Madara

    2014-01-01

    Unemployment to which young people are also subjected, is one of the main economical problems nowadays. The issue is actual also for Latvian youth. Therefore the theme of the Bachelor’s work is „Youth unemployment problems in Latvia”. The aim of the Bachelor’s work is to find out the current situation in the unemployment sphere, young people’s employment in Latvia as well as to work out solutions which could be used to solve the problem. The unemployment term, its types, causes and ef...

  12. Total employment effect of biofuels

    International Nuclear Information System (INIS)

    Stridsberg, S.

    1998-08-01

    The study examined the total employment effect of both direct production of biofuel and energy conversion to heat and electricity, as well as the indirect employment effect arising from investments and other activities in conjunction with the production organization. A secondary effect depending on the increased capital flow is also included in the final result. The scenarios are based on two periods, 1993-2005 and 2005-2020. In the present study, the different fuels and the different applications have been analyzed individually with regard to direct and indirect employment within each separate sector. The greatest employment effect in the production chain is shown for logging residues with 290 full-time jobs/TWh, whereas other biofuels range between 80 and 280 full-time jobs/TWh. In the processing chain, the corresponding range is 200-300 full-time jobs per each additional TWh. Additionally and finally, there are secondary effects that give a total of 650 full-time jobs/TWh. Together with the predicted increase, this suggests that unprocessed fuel will provide an additional 16 000 annual full-time jobs, and that fuel processing will contribute with a further 5 000 full-time jobs. The energy production from the fuels will provide an additional 13 000 full-time jobs. The total figure of 34 000 annual full-time jobs must then be reduced by about 4000 on account of lost jobs, mainly in the oil sector and to some extent in imports of biofuel. In addition, the anticipated increase in capital turnover that occurs within the biofuel sector, will increase full-time jobs up to year 2020. Finally, a discussion is given of the accomplishment of the programmes anticipated by the scenario, where it is noted that processing of biofuel to wafers, pellets or powder places major demands on access to raw material of good quality and that agrarian fuels must be given priority if they are to enter the system sufficiently fast. Straw is already a resource but is still not accepted by

  13. Employability Skills, Personal Qualities, and Early Employment Problems of Entry-Level Auditors: Perspectives from Employers, Lecturers, Auditors, and Students

    Science.gov (United States)

    Lim, Yet-Mee; Lee, Teck Heang; Yap, Ching Seng; Ling, Chui Ching

    2016-01-01

    The authors examine the issue of employability of university accounting students from the perspectives of accounting firm employers, junior auditors, accounting lecturers, and accounting students. Areas of investigation include perceived importance of employability skills and desirable personal qualities; and early employment problems encountered…

  14. Building Employer Capacity to Support Meaningful Employment for Persons with Developmental Disabilities: A Grounded Theory Study of Employment Support Perspectives.

    Science.gov (United States)

    Rashid, Marghalara; Hodgetts, Sandra; Nicholas, David

    2017-11-01

    To explore strategies to build employer capacity to support people with DD in meaningful employment from perspective of employment support workers. A grounded theory study was conducted with 34 employment support individuals. A theoretical sampling approach was used to identify and recruit participants from multiple sites in Ontario and Alberta. Three main themes, with seven sub-themes, emerged: (1) experiences of supporting employment finding for people with DD, (2) institutional influences on employee experiences, and (3) attitudes, assumptions and stigma. Several recommendations related to building employer capacity were offered. Our findings provide insight on specific elements and strategies that can support building employer capacity for persons with DD.

  15. 34 CFR 104.13 - Employment criteria.

    Science.gov (United States)

    2010-07-01

    ... 34 Education 1 2010-07-01 2010-07-01 false Employment criteria. 104.13 Section 104.13 Education Regulations of the Offices of the Department of Education OFFICE FOR CIVIL RIGHTS, DEPARTMENT OF EDUCATION... Employment Practices § 104.13 Employment criteria. (a) A recipient may not make use of any employment test or...

  16. 28 CFR 54.500 - Employment.

    Science.gov (United States)

    2010-07-01

    ... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Employment. 54.500 Section 54.500... in Employment in Education Programs or Activities Prohibited § 54.500 Employment. (a) General. (1) No... subjected to discrimination in employment, or recruitment, consideration, or selection therefor, whether...

  17. 41 CFR 101-4.500 - Employment.

    Science.gov (United States)

    2010-07-01

    ... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Employment. 101-4.500... Employment in Education Programs or Activities Prohibited § 101-4.500 Employment. (a) General. (1) No person... subjected to discrimination in employment, or recruitment, consideration, or selection therefor, whether...

  18. 14 CFR 1253.500 - Employment.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 5 2010-01-01 2010-01-01 false Employment. 1253.500 Section 1253.500... in Employment in Education Programs or Activities Prohibited § 1253.500 Employment. (a) General. (1..., or be subjected to discrimination in employment, or recruitment, consideration, or selection therefor...

  19. 15 CFR 8a.500 - Employment.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false Employment. 8a.500 Section 8a.500... in Employment in Education Programs or Activities Prohibited § 8a.500 Employment. (a) General. (1) No... subjected to discrimination in employment, or recruitment, consideration, or selection therefor, whether...

  20. 45 CFR 86.51 - Employment.

    Science.gov (United States)

    2010-10-01

    ... 45 Public Welfare 1 2010-10-01 2010-10-01 false Employment. 86.51 Section 86.51 Public Welfare... in Employment in Education Programs or Activities Prohibited § 86.51 Employment. (a) General. (1) No... subjected to discrimination in employment, or recruitment, consideration, or selection therefor, whether...